WorldWideScience
1

Evaluation of a solid hydrophone cable  

Energy Technology Data Exchange (ETDEWEB)

In marine seismic exploration, an approximately two-mile long hydrophone cable is towed behind the ship. The commonly employed cable consists of a kerosene-filled hose enclosing hydrophones, electrical wires, and steel ropes. The kerosene provides buoyancy while the steel ropes are for structural support. For deep-water operations, the cable is pulled through the water at a depth of 20-40 feet. For shallow water, a bottom reference configuration is used and the cable is dragged. This paper presents a comparison of electroacoustic properties between a newly designed, buoyant solid cable and those of the conventional kerosene-filled hose. The emphasis is on drag cable operations. Cable maintenance is a major problem. Jacket cuts occur because of improper handling or collisions with other ships, subsea structures, and debris. Kerosene leakage causes buoyancy loss and the need for immediate replacement. ...

1982-07-01

2

Using fiber optic sensors to protect intake, outflow, and other environmentally exposed openings  

Energy Technology Data Exchange (ETDEWEB)

This paper reports on the protection of opening that are exposed to the environment in nuclear facilities which presents an almost overwhelming engineering challenge. Intakes and outflows must permit the passage of large volumes of air or water without impeding their flow, and they are often exposed to corrosive salt and chemicals. An intrusion detection sensor that is intended to protect these openings must be capable of operating reliably under environmentally harsh conditions, and at the same time either provide a physical delay barrier or attach to an existing barrier. A new fiber optic sensor technology has now been developed specifically for protecting environmentally exposed openings. This sensor uses a fiber optic cable embedded in a neoprene rubber frame which is reinforced with Kevlar threads or braided steel cable. The sensor is configured in a mesh pattern with openings sufficiently large to permit air or ...

1991-01-01

3

Development and testing of a technology for insulating influx of stratum waters into producing wells with the use of a copolymer of methacrylic acid and diethyl ammonium salt  

Energy Technology Data Exchange (ETDEWEB)

Cited are the results of physico-chemical studies and industrial tests of a copolymer of methacrylic acid and diethylammonium salt, used for limiting the influx of stratum waters into a well.

1981-01-01

4

SALT WATER CORROSION TEST OF ROLLING SURFACE ...  

Science.gov (United States)

... by the Bureau. A canvas of supply sources produced only one other, the Flexo roller bearing swivel. Accordingly, only the ...

1955-04-04

6

Anomalous zones in Gulf Coast Salt domes with special reference to Big Hill, TX, and Weeks Island, LA  

Energy Technology Data Exchange (ETDEWEB)

Anomalous features in Gulf Coast Salt domes exhibit deviations from normally pure salt and vary widely in form from one dome to the next, ranging considerably in length and width. They have affected both conventional and solution mining in several ways. Gas outbursts, insolubles, and potash (especially carnallite) have led to the breakage of tubing in a number of caverns, and caused irregular shapes of many caverns through preferential leaching. Such anomalous features essentially have limited the lateral extent of conventional mining at several salt mines, and led to accidents and even the closing of several other mines. Such anomalous features, are often aligned in anomalous zones, and appear to be related to diapiric processes of salt dome development. Evidence indicates that anomalous zones are found between salt spines, where the differential salt ...

1993-07-01

7

FEBEX II Project Final report on thermo-hydro-mechanical laboratory tests  

International Nuclear Information System (INIS)

The results of the thermo-hydro-mechanical (THM) study of the FEBEX bentonite performed during FEBEX II are presented. The laboratory test program continued in part with the works carried out during FEBEX I, particularly in activities related to tests aimed to the calibration of the models, the acquisition of parameters by back-analysis and the improvement of the knowledge on the behaviour of expansive clays. But the program has also included tests on new areas: investigations about the influence of the microstructure changes in bentonite, of temperature and of the solute concentration on the behaviour of clay. Besides, several tests were proposed in order to understand the unexpected behaviour observed in the mock-up test, towards the end of year 2. Temperature effects on water retention curves in confined and unconfined conditions were determined, and swelling pressure, hydraulic conductivity and swelling and consolidation strains as a function of temperature ...

8

Development of engineering technology basis for pyrometallurgical reprocessing: development of transport technology and pyro-process equipments  

International Nuclear Information System (INIS)

Development of the engineering technology basis of pyrometallurgical reprocessing is a key issue for industrialization. For development of the transport technologies of molten salt and liquid cadmium at around 773 K, a salt transport test rig and a metal transport test rig were newly installed in an Ar glove box. Function of the salt transport test rig was confirmed with LiCl-KCl molten salt, and the transport behaviour of molten salt was found to follow that of water. The molten salt/liquid metal contactor for Ln/An separation was newly designed and installed. The test with a single-stage contactor was successful with simulated elements, and a three-stage contactor is now under development. A large-scale electro-refiner with a function to transport molten salt and liquid cadmium were newly designed, and to be installed ...

2006-09-25

9

Adsorption of di-2-ethylhexylphosphoric acid from toluene at interface with inorganic salt aqueous solutions  

International Nuclear Information System (INIS)

Interfacial tension at the aqueous solution of di-2-ethylhexylphosphoric acid or its copper salts/water solutions has been measured by the drop volume method.

10

Production of tetrazolium salts under conditions of phase-transfer catalysis  

Energy Technology Data Exchange (ETDEWEB)

Recently the authors showed that tetrazolium salts can be obtained during the oxidation of substituted 1,3,5-triarylformazans with potassium permanganate in a two-phase organic solvent-water system. The role of phase-transfer catalyst in this reaction is played by the tetrazolium salt, which is formed in a small amount as the result of oxidation of the formazan at the phase boundary. The method is distinguished by its extreme simplicity. However, the yield of the tetrazolium salts fluctuates within wide limits and does not exceed 62%. This is due to the fact that as the reaction proceeds the pH of the aqueous phase increases from 6 to 12. At the same time it is known that tetrazolium salts are unstable in aqueous alkaline solutions. They found that if the aqueous phase is replaced by aqueous hydrochloric acid (5 wt. %) the yields of the tetrazolium salts (Ia-g) ...

1988-06-20

11

Cloud-point measurement for (sulphate salts + polyethylene glycol 15000 + water) systems by the particle counting method  

International Nuclear Information System (INIS)

The phase separation of (water + salt + polyethylene glycol 15000) systems was studied by cloud-point measurements using the particle counting method. The effect of three kinds of sulphate salt (Na2SO4, K2SO4, (NH4)2SO4) concentration, polyethylene glycol 15000 concentration, mass ratio of polymer to salt on the cloud-point temperature of these systems have been investigated. The results obtained indicate that the cloud-point temperatures decrease linearly with increase in polyethylene glycol concentrations for different salts. Also, the cloud points decrease with an increase in mass ratio of salt to polymer.

2009-07-01

13

Network Security Defense Tools  

Science.gov (United States)

Lecturo on Firewalls, VPNs, Intrusion Detection, and filters

2009-02-11

14

Ambient water-quality criteria for ammonia (salt water)-1989  

Energy Technology Data Exchange (ETDEWEB)

Ammonia is a common and highly toxic pollutant which, in sufficient quantities, will adversely affect aquatic organisms. This ammonia criteria document for salt water will allow establishment of regulatory standards for ammonia discharge into estuaries, near coastal zones and oceans. Possible adverse impacts in highly sensitive and abundant ecosystems such as estuaries make regulation particularly important.

1989-04-01

15

Thermal gradient humidification-dehumidification desalination system  

Energy Technology Data Exchange (ETDEWEB)

A solar energy desalination process utilizing solar radiation directly for the evaporation of salt water is described. Ambient air takes on water vapor as the air passes through an evaporative medium. It is then directed between a saline water-covered, solar absorbing surface and a solar collecting housing. The resulting heated and moisture-saturated air is cooled in a heat exchange means where condensation of fresh water occurs. Simultaneously, cool salt water is utilized as the cooling water in the heat exchange means, and takes on the heat of condensation given up by the condensing vapor. The heated salt water from the heat exchange means is partially directed over the solar absorbing surface, and at least a portion of it is also directed to wet the evaporative medium. Several ...

1982-12-14

16

In situ monitoring of grouted electrolytes  

Energy Technology Data Exchange (ETDEWEB)

Cement-based composites are widely used in applications which demand long-term service life. One important example is in immobilization matrices for low-level radioactive and other hazardous wastes, which demands long-term retention and durability. The authors describe conductivity measurements of grouts flooded with water and in contact with a sink that consists of pure water. The conductivity measurements were designed and carried out in parallel with present quality verification methods and standard leach tests of the nuclear waste management industry. For the first time, the authors show that the method of replacing intrusive chemical analysis with conductivity measurements of the leaching samples yields equivalent results.

1996-04-01

17

Nomographs for the rapid prediction of salt quality and influent water quality impacts on hardness leakage in steamflood water  

Energy Technology Data Exchange (ETDEWEB)

Counter-current regeneration of 2-stage sodium zeolite softeners has been employed in reducing hardness leakage level of steamflooding water to less than 1 ppm when raw water contains as much as 5,000 ppm of the total dissolved solids. Hardness leakage is caused by sodium displacement of calcium and magnesium from the bottom of the exchanger bed. This study presents nomographs providing for rapid calculations to be made, for which a convenient operational mode does not already exist. The nomographs relate the hardness leakage as a function of salt quality and influent water quality and present solutions for predicting the leakage level, salt quality requirement or the treatability of raw water required for steamflooding projects.

1982-08-01

18

Origin of water salinity in the coastal Sarafand aquifer (South-Lebanon)  

International Nuclear Information System (INIS)

Author.The geochemical and isotopic study, based on the analysis of twenty water samples from well in the coastal plain of Sarafand (South-Lebanon), permit to eliminate the hypothesis of marine intrusion in this aquifer. The increase of salinity observed in certain wells is due to the contamination of cretaceous aquifer water by the quaternary formations. The two poles of mixing are respectively characterized: by weak tritium contents (between 2 and 3 UT) and a value of stable isotopes (-5,9<0,18<-5,5) corresponding to the appearance of cretaceous formation area; by the high tritium contents and enrichment relative to heavy isotope in the mineralized water of superficial formations. On the other hand, the isotope contents permit the set a rapid renewal of the cretaceous aquifer water due to quick circulation in the Karstic system

19

Effect of secondary circuit materials and water regime on steam generator reliability  

International Nuclear Information System (INIS)

The mechanism of the salt concentration increase in pits and crevices formed in a steam generator due to its imperfect manufacture or to its design features is described. The probability of corrosion can be reduced by choosing a suitable steel and by securing low concentrations of salts (chlorides in particular) and corrosion products in the feedwater. Attention is paid to the distribution of salts in the water-steam circuit and to the conditions of erosion corrosion as the principal source of corrosion products in feedwater. Experience with the suppression of erosion corrosion at nuclear power plants abroad is described. (E.J.).

1989-05-01

20

Integrating Phytoextraction and Biofortification: Fungal Accumulation of Selenium in Plant Materials from Phytoremediation of Agricultural Drainage  

Science.gov (United States)

The phytomanagement of Se-polluted soil and water is one strategy that may be environmentally sustainable and cost-effective for soils and waters enriched with natural-occurring Se. Several plant species, including Indian mustard (Brassica juncea), pickleweed (Salicornia bigelovii), and other salt/S...

21

Sodium monocarboxylates as inhibitors of AZ31 alloy corrosion in a synthetic cooling water  

Energy Technology Data Exchange (ETDEWEB)

This research investigated the inhibiting effects that sodium salts of linear monocarboxylic acids displayed towards the corrosion process of AZ31 Mg alloy in ASTM D 1387 saline solution (a synthetic industrial cooling water). The length of the aliphatic chain of the acids ranged between 7 and 15 carbon atoms. The inhibiting action of these salts can be related to the precipitation of an insoluble magnesium salt, which mainly affected the anodic reaction. The aliphatic chain length controlled the anion solubility and the reaction rate of magnesium carboxylate formation. For all the salts, an optimum concentration was experienced: 10{sup -2} M for sodium decanoate (caprate), 10{sup -3} M for sodium dodecanoate (laurate), 10{sup -4} M for sodium tetradecanoate (myristate); when this concentration was exceeded, a diminution (even a disappearance) in the inhibiting action was found. ...

2009-03-15

22

Water demand management in areas of ground water over-exploitation  

Environmental Research Database

SummaryIntended Outputs: Identification and evaluation, using participatory approaches, of demand management options:*Technical*Allocative and market based*Impact on target beneficiariesSupporting measures required when introducing water demand management options above:*Extension services & training*Water licences/rights*Institutional changes*Legal measures and regulation*Education*Support in diversifying to less water demanding activities*S [continued...]ObjectivesIdentification of the most appropriate demand management strategies for ground water abstraction, where aquifiers are being over-exploited, ensuring sustainable livelihoods of the vulnerable and poor are safeguarded. Poverty reduction strategies for areas where groundwater is being over-exploited.DescriptionProject Background: Groundwater is the principal source of both irrigation and domestic water supplies in many ...

2006-01-15

23

In situ corrosion studies on selected high level waste packaging materials under simulated disposal conditions in rock salt formations  

International Nuclear Information System (INIS)

This paper reports about in-situ corrosion studies on selected materials for long-term resistant high-level waste (HLW) packagings acting as a barrier in a rock salt repository. The materials (Ti 99.8-Pd, Hastelloy C4 and five iron-base materials) were investigated in heated boreholes in the Asse salt mine under simulated HLW disposal conditions prevailing in normal operation of repository and in certain accident scenarios. The experiments under normal operating conditions were performed at temperatures of 120 deg. C to 210 deg. C (vertical temperature profile in the boreholes) without and with gamma irradiation (3#centre dot#10"2 Gy/h, Co-60 source) within the framework of the German/US Brine Migration Test. In these experiments only small amounts of migrated brine inclusions (NaCl-rich) from the rock salt were present as corrosion medium. In the experiments carried out under simulated accident conditions with ...

1993-02-01

24

Rapid and continuous hydrothermal crystallization of metal oxide particles in supercritical water  

Energy Technology Data Exchange (ETDEWEB)

This paper reports on hydrolysis of 10 metal salt aqueous solutions of 6 metal oxides that was conducted in supercritical water. Continuous and rapid production of metal oxide fine particles was achieved by mixing a metal salt aqueous solution with preheated water fed from another line. The reaction time required was less than 2 min. Particle size, morphology, and crystal structure of the obtained metal (hydrous) oxides were examined. Particle size (20 to 600 nm) was different among the system but the size range was relatively narrow in all the cases.

1992-04-01

25

LiNO3 molten salt assisted synthesis of spherical nano-sized YSZ powders in a reverse microemulsion system  

British Library Electronic Table of Contents (United Kingdom)

Spherical nano-sized YSZ (yttria stabilized ZrO2) powders were successfully synthesized via a reverse microemulsion system. The water droplets in the microemulsion system of yclohexane/water/span85/Triton X-100/hexyl alcohol can act as the nano-reactors which solubilize zirconium oxychloride and ammonia water separately. The minute original reactors are favor to the formation of nano-sized spherical YSZ powders and the dispersibility of the powders can be controlled effectually by adjusting the weight ratio of the LiNO3 molten salt to the precursor. The phase transformation from cubic to monoclinic starts at and 500??C and finally monoclinic and cubic phase with increased crytallinity coexist at 800??C. The effect of LiNO3 molten salt in the formation of YSZ powders was also discussed.

2008-01-01

26

Quartz ceramics alloying  

International Nuclear Information System (INIS)

The following methods of quartz ceramics alloying were considered: alloying of initial quartz glass; introduction of alloying additive into water slip of quartz glass; porous materials impregnation with salt aqueous solutions and subsequent salt thermal decomposition with formation of stable oxides in pores of ceramics. Oxygen free compounds BN, SiB_4, SiC, Si_3N_4, REM oxides and transition metal oxides were used as alloying additives. Main properties of the materials and compositions obtained are presented.

27

Effect of water content on the activity of lipase-hydrolysis of olive oil in reverse micelles. Gyakuso micelle nai ni okeru lipase no olive oil kasui bunkai hanno no gansuiritsu izonsei  

Energy Technology Data Exchange (ETDEWEB)

Hydrolysis of olive oil by Chromobacterium viscosum lipase was studied in a reverse micellar system of a anionic surfactant Aerosol OT (AOT) and isooctane. Different methods of solubilization of the micellar system afford specific dependence of enzymatic activity of the lipase on the water content in the micelles. In an injection method, water content is controlled by the amount of injected water, which determines the micelle size and hydrophobicity of the micelle without salt addition and changes reversibly the conformation of lipase corresponding to the change of lipase activity. The activity reaches the maximum at a water content (water/AOT)of 7. In a phase transfer method, water content is determined by salt concentration in the aqueous phase in contact with micelles and the water content ...

1992-01-10

28

Vapor fraction measurements in a steam-water duct at atmospheric pressure using neutron radiography  

Energy Technology Data Exchange (ETDEWEB)

Real-time neutron radiography has been used to study the dynamic behavior of two-phase flow and measure vapor fractions in a steam-water duct at atmospheric pressure. This unique experimental technique offers one the opportunity to observe and record on videotape now Patterns and transient behavior of two-phase flow inside opaque containers without perturbing the environment. The neutron radiographic technique is non-intrusive and requires no special transparent window region. Data are recorded simultaneously over a large area of interest. Image processing of the video data can be employed to measure bubble velocities and time-averaged and Instantaneous vapor fractions.

1994-11-11

29

Monitoring Coastal Marshes for Persistent Saltwater Intrusion  

Science.gov (United States)

Primary goal: Provide resource managers with remote sensing products that support ecosystem

2009-01-01

30

Coastal Marsh Monitoring for Persistent Saltwater Intrusion  

Science.gov (United States)

This viewgraph presentation reviews NASA's work on the project that supports the Gulf of Mexico

2008-01-01

31

Reinfusion of ascites during hemodialysis as a treatment of massive refractory ascites and acute renal failure  

UK PubMed Central (United Kingdom)

Refractory ascites can occur in patients with various conditions. Although several procedures based on the reinfusion of ascitic fluid have been reported after the failure of bed rest, salt and water...Full Text Available

32

LITERATURE SURVEY OF THE CORROSION BEHAVIOR OF TANTALUM, ZIRCONIUM, AND TITANIUM  

Science.gov (United States)

The corrosion behavior of Ta, Ti, and Zr in inorganic acids, bases, chlorides and miscellaneous salts, waters and gases, and organic acids and miscellaneous organic chemicals is summarized. (W.L.H)

1955-02-23

33

Hydrogeochemistry of seasonal variation of Urmia Salt Lake, Iran  

UK PubMed Central (United Kingdom)

Urmia Lake has been designated as an international park by the United Nations. The lake occupies a 5700 km2 depression in northwestern Iran. Thirteen permanent rivers flow into the lake. Water level...Full Text Available

34

Chalk Point Cooling Tower Project: Drift Salinity Experiments.  

Science.gov (United States)

Results of feasibility experiments for determining the mineral content of individual stains on special Sensitized Paper are presented. The stains were formed on the paper by the impaction of laboratory generated salt water droplets. Of the techniques exam...

1979-01-01

35

The characteristics of a hydroxyapatite-chitosan-PMMA bone cement.  

Science.gov (United States)

In this study, we propose a new bioactive bone cement (BBC), composed of natural bone powder (hydroxyapatite; HA), chitosan powder, and the currently available polymethylmethacrylate (PMMA) bone cement, for use in orthopedic surgeries such as vertebroplasty or as bone filler. Three types of BBCs (BBC I, BBC II, and BBC III) were prepared with different composition ratios. In vitro tests and animal studies were performed with the new BBCs, and with a currently available commercial PMMA bone cement. Surface morphology, chemical composition, changes in pH over time, exothermic temperatures, intrusion, and cellular responses were investigated in vitro. Scanning electron microscopy (SEM) and radiological and histological examinations were performed in animal studies. The results showed that the major components of the BBCs were C, O, Ca, P, Cl, Si, S, Ba, and Mg. The pH values of the BBCs decreased after 1 day, but eventually recovered to 7.2-7.4. The ...

2004-11-01

36

On-farm water management in saline groundwater area under scarce canal water supply condition in the Northwest India  

British Library Electronic Table of Contents (United Kingdom)

The study investigates the possibility of enhancing crop water productivity in the parts of Northwest India where groundwater quality is marginal and canal water supply is severely scarce. Soil, Water, Atmosphere and Plant (SWAP) model was calibrated and validated in three farmers' fields with varying canal water availability and groundwater quality in the Kaithal Irrigation Circle of the Bhakra Canal system, Haryana. On the basis of predicted and observed soil water content, pressure heads, salt concentration at 2 week intervals and crop yields, the model was found suitable for use in the region. A few nomographs were prepared to provide a graphical method to predict the effect of different combinations of water quality and depth of water application on crop yield and soil salinity and to...

2008-01-01

37

An overview of physical and biogeochemical processes and ecosystem dynamics in the Taiwan Strait  

British Library Electronic Table of Contents (United Kingdom)

The Taiwan Strait is an important channel in the west Pacific Ocean transporting water and chemical constituents between the East China Sea and the South China Sea. Due to its complex bottom topography, alternating monsoon forcing and conjunction of several current systems [such as the Zhejiang-Fujian (Zhe-Min) Coastal Current, the Kuroshio intrusion and the extension of the South China Sea Warm Current], the physical and biogeochemical processes and ecosystem dynamics in the Taiwan Strait vary significantly both in space and in time. Our recent interdisciplinary studies, combining in situ and remote sensing observations with numerical modeling, allow us to address several important issues concerning the Taiwan Strait. The temporal and spatial variation of circulation in the Taiwan Strait ...

2011-01-01

38

Long term mineralogical changes in salt formations due to water and brine interactions  

International Nuclear Information System (INIS)

Four very common long term mineralogical changes in salt formations are discussed in the view of the safety considerations for underground repositories. Two of these processes, the 'Hartsalz' and 'Carnallite' dissolution were studied in two scale in situ experiments. The results are presented and compared with the results of the geochemical modelling with the computer code EQ3/6. Furthermore the reactions leading to the formation of the gypsum cap rock on the top of the Zechstein salt formations and to the polyhalitization of anhydrite are discussed. Geological field observations and mineral assemblages agree well with the results of the geochemical modelling employing the Pitzer formalism along with the Harvie, Moller and Weare database. We conclude that once the mechanisms of the chemical reactions are well understood it becomes possible to evaluate realistically whether such processes, when encountered in the repository, are still active or ...

1994-09-01

39

Improved salt tolerance and seed cotton yield in cotton (Gossypium hirsutum L.) by transformation with betA gene for glycinebetaine synthesis  

British Library Electronic Table of Contents (United Kingdom)

Homozygous transgenic cotton (Gossypium hirsutum L.) plants that accumulated glycinebetaine (GB) in larger quantities were more tolerant to salt than wild-type (WT) plants. Four transgenic lines, namely 1, 3, 4, and 5, accumulated significantly higher levels of GB than WT plants did both before and after salt stress. At 175 and 275?mM NaCl, seeds of all the transgenic lines germinated earlier and recorded a higher final germination percentage, and the seedlings grew better, than those of the WT. Under salt stress, all the lines showed some characteristic features of salt tolerance, such as higher leaf relative water content (RWC), higher photosynthesis, better osmotic adjustment (OA), lower percentage of ion leakage, and lower peroxidation of the lipid membrane. Levels of endogenous GB in ...

2011-01-01

40

Investigation of the removal efficiency of gasborne particles in a scrubber column  

Energy Technology Data Exchange (ETDEWEB)

Tests on the scrubbing column have led to the following results: Use of a scrubbing column with Raschig rings is only meaningful for the sedimentation of particles exceeding diameters of 0.5 ..mu..m; drops of diameter size 1.5 ..mu..m are formed in the column; more efficient drop precipitators in the column air flow ease the load on subsequent suspended material filters thereby contributing to a longer life of these filters even at higher sodium ion concentrations in the washing water; with distillate of an 8% rather than 0.8% salt solution a decontamination factor greater than 10 can be calculated since larger particles precipitate more readily. This only applies, however, under the condition that the washing water is renewed regularly, if necessary daily where higher aerosol concentrations are present. If not, the decontamination factor will be reduced through the salt-containing secondary aerosols ...

1983-01-01

41

Investigation of the removal efficiency of gasborne particles in a scrubber column  

International Nuclear Information System (INIS)

Tests on the scrubbing column have led to the following results: Use of a scrubbing column with Raschig rings is only meaningful for the sedimentation of particles exceeding diameters of 0.5 #mu#m; drops of diameter size 1.5 #mu#m are formed in the column; more efficient drop precipitators in the column air flow ease the load on subsequent suspended material filters thereby contributing to a longer life of these filters even at higher sodium ion concentrations in the washing water; with distillate of an 8% rather than 0.8% salt solution a decontamination factor greater than 10 can be calculated since larger particles precipitate more readily. This only applies, however, under the condition that the washing water is renewed regularly, if necessary daily where higher aerosol concentrations are present. If not, the decontamination factor will be reduced through the salt-containing secondary aerosols from ...

42

Luminescence of terbium(III) chloride in porous glass  

International Nuclear Information System (INIS)

Capsulation of terbium(III) chloride in porous glass in the amount of 1.5-150 #mu#mole g"-"1 was carried out by impregnation of the glass substrate with variable concentrations of the salt aqueous solutions. Maximum luminosity of terbium(III) chloride in porous glass is found at its concentration of 120 #mu#mole g"-"1, that is close to the corresponding monolayer surface filling. Concentration dependences of terbium(III) luminescence and its quenching by adsorbed water are in agreement with the ideas of molecular fragmentation and uniform distribution of capsulated salt on the substrate surface

2007-03-01

43

Kinetics of salt concentration in heated crevices  

International Nuclear Information System (INIS)

In PWR steam-generators, the crevice between tube and tube-support plate tends to fill with porous deposits during operation and acts as a concentration site for chemicals in the boiler water, which may lead to corrosion of the tube and tube-support-plate. The rate of concentration, the magnitude of the concentration factor and the rate of release of solute when conditions change are important parameters for devising strategies to minimize corrosion. Values of these parameters for salt concentration have therefore been measured in a laboratory simulation of the crevice and are used to formulate a model of the concentrating process.

1985-03-01

44

Hazard Evaluation for the Saltwell Chempump and a Saltwell Centrifugal Pump Design using Service Water for Lubrication and Cooling  

Energy Technology Data Exchange (ETDEWEB)

This report documents results of a preliminary hazard analysis (PHA) covering the existing Crane Chempump and the new salt well pumping design. Three hazardous conditions were identified for the Chempump and ten hazardous conditions were identified for the new salt well pump design. This report also presents the results of the control decision/allocation process. A backflow preventer and associated limiting condition for operation were assigned to one hazardous condition with the new design.

2000-11-16

45

W1045 environment surf drip shield and waste package outer barrier  

Energy Technology Data Exchange (ETDEWEB)

The environments on the drip shield and waste package outer barrier are controlled by the compositions of the waters that contact these components. the temperature (T) of these components, and the effective relative humidity (RH) at these components. Because the composition of the waters that are expected to enter the emplacement drifts (either by seepage flow or by episodic flow) have not been specified: well J13 water was chosen as the reference water (Harrar 1990). Section 6.2 discusses the accessible RH for the temperatures of interest at the repository horizon. Section 6.3 discusses the adsorption of water on metal alloys in the absence of hygroscopic salts. Because the temperatures of the DSs and the WPOBs are higher than those of the surrounding near-field environment, the relative humidity at the DSs and the WPOBs will be lower than that of the ...

1999-07-14

46

The preparation of highly absorbing cellulosic copolymers -the cellulose acetate/propionate-g. co-acrylic acid system  

Energy Technology Data Exchange (ETDEWEB)

A series of copolymers based on the cellulose acetate/propionate-g.co-acrylic acid system has been prepared under radiation-induced control. These copolymers have been assessed for their water-retention capacity both in an unmodified state and after ''decrystallization'' or ''neutralization'' treatments. The grafting of acrylic acid onto the cellulose acetate/propionate had little effect on the water retention power of the cellulose acetate/propionate. However, improvements to the water retentivity was obtained after ''decrystallization'' procedures had been carried out on the copolymers using selected alkali metal salts with methanol as the continuous medium. The water-retentivity of the copolymers increased with increase in the extent of grafting, though the effect is less ...

1990-01-01

47

Formulation and make-up of simulate dilute water, low ionic content aqueous solution  

Energy Technology Data Exchange (ETDEWEB)

This procedure describes the formulation and make-up of Simulated Dilute Water (SOW), a low-ionic-content water to be used for Activity E-20-50, Long-Term Corrosion Studies. This water has an ionic content which is nominally a factor of ten higher than that of representative waters at or near Yucca Mountain. Representative waters were chosen as J-13 well water [Harrar, 1990] and perched water at Yucca Mountain [Glassley, 1996]. J-13 well water is obtained from ground water that is in contact with the Topopah Spring tuff, which is the repository horizon rock. The perched water is located in the Topopah Spring tuff, but below the repository horizon and above the water table. A nominal times ten higher ionic content was chosen to simulate the effect of ionic ...

1997-04-04

48

The Modeling of Boattail Intrusion in a Lumped Parameter ...  

Science.gov (United States)

... characteristics of combustible cartridge cases (Robbins, Koszoru, and Minor 1986), interior ballistic simulations using XNOVAKTC ...

1993-08-01

49

Brochure 1 - NASA  

Science.gov (United States)

exposed to persistent saltwater intrusion, a major factor in the decline of marsh ecosystems. The resulting increase in salinity from persistent flooding due to ...

50

Use of the River Saale cascade in terms of energy supply and water control. Energetische und wasserwirtchaftliche Nutzung der Saale-Kaskade  

Energy Technology Data Exchange (ETDEWEB)

The river Saale cascade consists of seven reservoirs with a total capacity of approx. 415 Mio. m[sup 3]. The entire reservoir system covers a catchment area of 1665 km[sup 2]. The water management tasks extend to the following main fields: flood protection upkeep of minimum water stock, salt load control and power generation. The energy supply capacity of the cascade is mainly used by pumped storage plants. The last of these plants, Hohenwarte II, was put into service in 1963. (orig.)

1993-01-01

51

Transcriptome analysis reveals salt-stress-regulated biological processes and key pathways in roots of cotton (Gossypium hirsutum L.).  

Science.gov (United States)

High salinity is one of the main factors limiting cotton growth and productivity. The genes that regulate salt stress in TM-1 upland cotton were monitored using microarray and real-time PCR (RT-PCR) with samples taken from roots. Microarray analysis showed that 1503 probe sets were up-regulated and 1490 probe sets were down-regulated in plants exposed for 3h to 100mM NaCl, and RT-PCR analysis validated 42 relevant/related genes. The distribution of enriched gene ontology terms showed such important processes as the response to water stress and pathways of hormone metabolism and signal transduction were induced by the NaCl treatment. Some key regulatory gene families involved in abiotic and biotic sources of stress such as WRKY, ERF, and JAZ were differentially expressed. Our transcriptome analysis might provide some useful insights into salt-mediated signal transduction pathways in cotton and offer a number of candidate ...

2011-04-30

52

Development of engineering technology basis for industrialization of pyrometallurgical reprocessing  

International Nuclear Information System (INIS)

Development of the engineering technology basis of pyrometallurgical reprocessing is a key issue for industrialization. For development of the transport technologies of molten salt and liquid cadmium at around 500 deg. C, a salt transport test rig and a metal transport test rig were installed in Ar glove box. Function of centrifugal pump and 1/2'' declined tubing were confirmed with LiCl- KCl molten salt. The transport behavior of molten salt was found to follow that of water. Function of centrifugal pump, vacuum sucking and 1/2'' declined tubing were confirmed with liquid Cd. With employing the transport technologies, industrialization applicable electro-refiner was newly designed and engineering-scale model was fabricated in Ar glove box. The electro-refiner has semi-continuous liquid Cd cathode instead of conventional one used in small-scale tests. With using actinide-simulating ...

2007-09-09

53

Study of age hardening behavior of Al-4.5wt%Cu/zircon sand composite in different quenching media - A comparative study  

British Library Electronic Table of Contents (United Kingdom)

The age hardening behavior of Al-4.5%Cu alloy composite reinforced with zircon sand particulates and produced by stir casting route has been investigated in different quenching media viz, water, oil, and salt brine solution (7wt%). Optical microscopy of the as cast alloy composite indicates that the matrix of the composite has the cellular structure. Copper rich CuAl2 precipitates have been found near particle matrix interface. The results of ageing demonstrate that the microhardness of age hardenable Al-Cu based alloy composites depend on the quenching medium in which they are heat treated. Salt brine quenching is faster as compared to water and oil, even if higher strength is obtained but cannot be used for complex shapes and thin sections where oil quenching is the alternative due to mi...

2009-01-01

54

Development of ultrafiltration and adsorbents: October 1979-March 1980  

Energy Technology Data Exchange (ETDEWEB)

Tests on a sample of trench water from the Maxey Flats burial ground effectively demonstrated the new Reverse Osmosis Pilot Plant. The effluent from the 50% salt-rejection membrane was decontaminated well enough with the exception of tritium to be discharged to the environment. The performance of the 97% salt-rejection membrane was superior to that of the 50% membrane. A breakthrough and capacity experiment was conducted with Durasil 10 on a simulated Three Mile Island solution. The maximum decontamination factor was extrapolated to be 10/sup 6/, which would reduce the cesium level of TMI water to below the discard limit. Capacity (1/DF = 0.5) was reached at 1260 column volumes. Several adsorbents were tested in the engineering columns for decontamination of cesium-bearing solutions. Under the conditions of the experiment, these adsorbents were ineffective in removing cesium from the solution.

1980-07-02

57

Configurable Middleware-Level Intrusion Detection for Embedded Systems  

Energy Technology Data Exchange (ETDEWEB)

Embedded systems have become integral parts of a diverse range of systems from automobiles to critical infrastructure applications such as gas and electric power distribution. Unfortunately, research on computer security in general and intrusion detection in particular, has not kept pace. Furthermore, embedded systems, by their very nature, are application specific and therefore frameworks for developing application-specific intrusion detection systems for distributed embedded systems must be researched, designed, and implemented. In this paper, we present a configurable middleware-based intrusion detection framework. In particular, this paper presents a system model and a concrete implementation of a highly configurable intrusion detection framework that is integrated into MicroQoSCORBA, a highly configurable middleware framework developed for embedded systems. By exploiting the application-specific ...

2005-06-20

58

Session 1: Geothermal Pumping Systems and Two-Phase Flow Studies  

Energy Technology Data Exchange (ETDEWEB)

Improvements in electric submersible pumping systems have resulted in a demonstrated downhole running life of one year for low horsepower units operating in 180 C brine. The implementation of a prototype pressurized lubrication system to prevent brine intrusion and loss of lubricating oil from the motor and protector sections has been successfully tested. Second generation pressurized lubrication systems have been designed and fabricated and will be utilized in downhole production pumping tests during FY84. Pumping system lifetime is currently limited by available power cable designs that are degraded by high-temperature brine. A prototype metal-sheathed power cable has been designed and fabricated and is currently undergoing destructive and nondestructive laboratory testing. This cable design has the potential for eliminating brine intrusion into the power delivery system through the use of a hermatically sealed cable from the surface to the ...

1983-12-01

59

Real-time management of water quality in the San Joaquin River Basin, California.  

Energy Technology Data Exchange (ETDEWEB)

In the San Joaquin River Basin, California, a realtime water quality forecasting model was developed to help improve the management of saline agricultural and wetland drainage to meet water quality objectives. Predicted salt loads from the water quality forecasting model, SJRIODAY, were consistently within +- 11 percent of actual, within +- 14 percent for seven-day forecasts, and with in +- 26 percent for 14-day forecasts for the 16-month trial period. When the 48 days dominated by rainfall/runoff events were eliminated from the data set, the error bar decreased to +- 9 percent for the model and +- 11 percent and +- 17 percent for the seven-day and 14-day forecasts, respectively. Constraints on the use of the model for salinity management on the San Joaquin River include the number of entities that control or influence water quality and the lack of a centralized authority to direct ...

1997-09-01

60

Soil water retention at varying matric potentials following repeated wetting with modestly saline-sodic water and subsequent air drying  

Energy Technology Data Exchange (ETDEWEB)

Coal bed natural gas (CBNG) development in the Powder River (PR) Basin produces modestly saline, highly sodic wastewater. This study assessed impacts of wetting four textural groups (0-11%, 12-22%, 23 -33%, and > 33% clay (g clay/100 g soil) x 100%))with simulated PR or CBNG water on water retention. Soils received the following treatments with each water quality: a single wetting event, five wetting and drying events, or five wetting and drying events followed by leaching with salt-free water. Treated samples were then resaturated with the final treatment water and equilibrated to -10, -33, -100, -500, or -1,500 kPa. At all potentials, soil water retention increased significantly with increasing clay content. Drought-prone soils lost water-holding capacity between saturation and field capacity with repeated ...

2007-07-01

61

dmoc0a4.PDF  

Wastenet

Sprat Sprat in the Southwestern Baltic Sea (including Sound and Belt Sea) ...episodic salt water inflows which occur during autumn to spring.The last major inflow to the Baltic Proper ...The small inflows in spring 1986 and fall 1988 have had only effects on salinity and temperature

62

Stress Corrosion Cracking Susceptibility of Beta Titanium Alloy 38-6-44: Candidate Alloy for Scout Torsion Bar.  

Science.gov (United States)

The threshold stress itensities for stress corrosion crack propagation in beta titanium alloy 38-6-44, Ti-3Al-8V-6Cr-4Mo-4Zr, has been determined in salt water and methanolic solutions. The alloy was immune to stress corrosion cracking in aqueous sodium c...

1974-01-01

63

Sorption of gold by activated charcoal from cyan-containing solutions of complex salt composition  

Energy Technology Data Exchange (ETDEWEB)

An evaluation was made of the effectiveness of the action of reagents used for cleaning cyan-containing waste water for conditioning of the overflow of copper concentrate thickners of the Belousovskiy enrichment before sorption extraction of gold by activated charcoal. It was established that conditioning of the overflow by iron sulfates (II), copper and zinc diminshes, and by hypochlorite increases the capacitance of the activated charcoal for gold.

1982-01-01

64

On the calculation of the electrolyte aqueous solution freezing temperature  

International Nuclear Information System (INIS)

Analytical expression of the dependence of freezing temperature of electrolyte (CdCl_2, CdSO_4, BeSO_4) aqueous solutions on their composition was found. Three different methods were suggested were suggested for calculation of water activity in multicomponent solution. It was established that sublinear extrapolation of freezing temperature of salt aqueous solutions was possible not up to -5 deg C, but up to -15 deg C, independently of their composition. 6 refs.; 2 figs.

65

Laboratory evaluation of the feasibility of chemical oxidation processes for treatment of contaminated groundwaters. Final report  

Energy Technology Data Exchange (ETDEWEB)

Chemical oxidation is a treatment technology that uses powertul chemical oxidizers to destroy organic contaminants. Typical oxidizers used in chemical oxidation processes include ozone, hydrogen peroxide, chlorine, and potassium permanganate. The chemical reaction products are usually simple organic compounds, such as carboxylic acids, and/or inorganic compounds, such as carbon dioxide, water, and simple inorganic complexes (e.g., chloride salts, in the case of chemical oxidation treatment of chlorinated solvents).

1995-09-01

66

Inland wetlands legislation and management. (Latest citations from the NTIS data base). Published Search  

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning Federal and state laws and management programs for the protection and use of inland wetlands. Utilization of wetlands to control highway runoff and community wastewater is discussed. Wetlands protection programs, restoration projects, resource planning, and wetlands identification methods are cited. References to coastal and salt water wetlands are not included in this bibliography. (Contains 250 citations and includes a subject term index and title list.)

1992-05-01

67

Effect of hydrogen on structure and properties of #beta#-titanium alloy VT-15 during bending tests in various media  

International Nuclear Information System (INIS)

It is shown that bending tests on microsamples can be used to study the conditions in which hydrogen brittleness develops. In such tests hydrogen brittleness develops in the VTI5 alloy within the temperature range +5 to -20"0C. The tendency of VTI5 to develop hydrogen brittleness is enhanced with bending in salt water. (author).

68

All the Spent Nuclear Wastes to Low and Intermediate Level Wastes: PyroGreen  

International Nuclear Information System (INIS)

Spent nuclear wastes are inevitable issues to use nuclear power as a sustainable energy. Therefore, every country has their fuel cycles which are best for their environmental and/or political circumstances for the use of nuclear energy. These days agreements are made that spent nuclear fuels should be recycled to minimize waste volume and its toxicity all around the world. Republic of Korea also has a plan to recycle the spent nuclear fuels by using Gen-IV concept burner reactors and pyro-process plants. Not many options of national nuclear strategies are exist because Korea has too many people for its limited land space. KAERI already has been proposing a national fuel cycle concept called 'KIEP-21' that encompasses all the requirements of the advanced nuclear fuel cycle such as reduction of volume, toxicity, HLW heat load and so on. Authors suggest non-national fuel cycle concept called 'PyroGreen' for the sustainable nuclear energy system. PyroGreen is also comprised of ...

2009-06-01

69

The Polish Nuclear Society on the energy situation in Poland  

Energy Technology Data Exchange (ETDEWEB)

Discusses the resolution of the 2. Congress of the Polish Nuclear Society on the energy situation in Poland and recommendations for energy policy. Recommendations for use of nuclear power plants in Poland are made considering environmental pollution from coal combustion (air pollution by sulfur dioxide, nitrogen oxides and carbon dioxide as well as water pollution by salt from mine water discharged to rivers), development of the Polish economy, forecast increase in energy consumption and the role of nuclear energy in other European countries. Research on nuclear power plants, safety and environmental aspects as well as comparative efficiency of coal-fired power plants and nuclear power plants is evaluated.

1993-10-01

70

Studies on technology improvement in the production of iodine and bromine  

International Nuclear Information System (INIS)

Results of studies dealing with improvement of the currently employed technology of iodine and bromine production by processing iodine- and bromine-containing borehole effluent water were considered. Potentiality of selective oxidation of iodide-ions in the presence of bromide-ions in acidified borehole effluent water with addition of ozone for initiating oxidation of iodide-ions and iron(2) salt to prevent bromine evolution was confirmed experimentally. Conditions were determined that rule out bromine formation in the solution, but simultaneously permit varying the yield of iodine within 70-100%

2001-07-01

71

Inland wetlands legislation and management. January 1970-September 1989 (Citations from the NTIS data base). Report for January 1970-September 1989  

Energy Technology Data Exchange (ETDEWEB)

This bibliography contains citations concerning Federal and state laws and management programs for the protection and use of inland wetlands. Utilization of wetlands to control highway runoff and community waste water is discussed. Wetlands protection programs, restoration projects, resource planning, and wetlands identification methods are cited. References to coastal and salt-water wetlands are excluded from this bibliography. (This updated bibliography contains 219 citations, 37 of which are new entries to the previous edition.)

1989-10-01

72

Anaerobic oxidation of carbon steel in granitic groundwaters: A review of the relevant literature  

International Nuclear Information System (INIS)

This report reviews the published literature on the anaerobic oxidation of iron in aqueous solutions which are of particular relevance to Swedish granitic groundwaters. The thermodynamics of iron corrosion in water are briefly considered. Following this the experimental data found in the literature are presented and discussed. Results were found for corrosion of iron in both pure water and solutions containing mineral salts. The literature work in the nature of the films formed on iron surfaces under anaerobic conditions is reviewed and the possible mechanisms of film formation are discussed. Conclusions are drawn on the factors most likely to influence and control film growth. 32 refs.

2010-02-01

73

Use of sodium aluminate in waste water treatment plants: wishes of saving money and innovating; Uso del aluminato sodico en las EDAR: una propuesta para innovar y economizar costes de explotacion  

Energy Technology Data Exchange (ETDEWEB)

Most waste water treatment plants have processes to remove nutrients in order to avoid eutrophication in water receiving bodies. Regarding phosphorus removal. the most common option is chemical precipitation with ferric or aluminical precipitation with ferric or aluminium salts. We show here the successful experience carried out by the WWTP of Blanes and the company Safloc. A method ato remove phosphorus from waste water was developed by adding sodium aluminate. The use of this compound has turned out to be a sustainable way for this purpose in terms of costs, reliability and minimization of sludge production. (Author)

2006-07-01

74

Changes in water qualities and human activities at the urban coastal areas; Toshienganiki niokeru suishitsuhenkann to ningen katsudo  

Energy Technology Data Exchange (ETDEWEB)

The population masses in many coastal zones in Japan, and human activities are greatly effected. The representative water area is the Tokyo Bay. The population of the Tokyo Bay reaches 26 million at present, and a mass of organic substance and nutrient salt flow into it through rivers and sewage-treatment plants, etc. With the improvement of pollution source countermeasure and sewerage in the area, the inflow load to the Bay gradually decreases, but in the inner bay, red tide is generating in the summertime mainly. And, the anoxic water areas observed in bottom layer in summertime make large effects on the seafood. It is a large theme to clarify formation process of the anoxic water area and to solve this problem for the Tokyo Bay in the twenty-first century. In this paper, changes in water qualities and human activities and fundamental approach of water quality ...

2000-01-05

75

Surface modification on magnesium alloys by coating with magnesium fluorides  

Energy Technology Data Exchange (ETDEWEB)

A new technique has been developed for improving corrosion resistance on magnesium alloys. Specimens of AZ31 magnesium alloy were dipped into molten salt of NaBF{sub 4} at 723 K for various times, and then cooled, rinsed with water, and dried in air. Corrosion resistance in the surface treated specimens was evaluated by salt immersion test using 1% NaCl solution as a time for occurring filiform corrosion. On an un-treated AZ31 alloy, the time for starting the filiform corrosion was about 1.2 ks, while on the surface treated specimen, the time was prolonged into about 1300 ks. Moreover, the surface treated specimen showed corrosion resistance in low pH solutions, such as 1% HNO{sub 3} and HCl solutions. (orig.)

2005-07-01

76

Workshop Agenda - Applied Science and Technology Project Office - NASA  

Science.gov (United States)

Purpose: Assess the feasibility of using NASA satellite data to monitor persistent saltwater intrusion in coastal marshes. End User: USGS National Wetlands ...

77

UNIX Security Guideline v1.0 - NASA Headquarters  

Science.gov (United States)

5.2 Network Security. The features listed below can be used to help safeguard UNIX ...... The LaRCSCAN non-intrusive network security scanner package, ...

78

Non-Intrusive, Laser-Based Imaging of Jet-A Fuel Injection and Combustion Species in High Pressure, Subsonic Flows  

Science.gov (United States)

The emphasis of combustion research efforts at NASA Glenn Research Center (GRC) is on collaborating

2000-01-01

79

Single-Electrode Capacitance and Charged State in Interfacial Region within Nano-Porous Carbon Electrode for Electric Double Layer Capacitor; Kasseitan denki 2jyuso kyapasita no tankyoku seiden yoryo to koeki kaimen chikuden jyotai  

Energy Technology Data Exchange (ETDEWEB)

The single-electrode capacitance of a nano-porous carbon electrode used as an electric double layer capacitor was measured. The charged state of the electrolyte ion was discussed from the results. Single-electrode capacitance was not proportional to the specific surface area of the electrode. This implies that the whole surface of the electrode is not effective for the formation of an electric double layer. It is considered that edge orientation of the carbon structure would give a dominant contribution to capacitance. For measurements with aqueous solutions of various electrolytes, capacitance was about the same value for each salt compound. For aqueous acid solution, on the other hand, capacitance was twice to three times as large as that for salt compounds. This difference, however, became negligibly small if the concentration of electrolyte solution was lowered. Taking account of the hydrated ionic radius of each ion, it was considered that ...

1997-07-10

80

Influence of temperature on strength of cemented surrogate nitrate salt waste  

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste form increased with brine temperature, and waste forms from brine at the boiling ...

1993-01-01

81

Influence of temperature on strength of cemented surrogate nitrate salt waste  

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste form increased with brine temperature, and waste forms from brine at the boiling ...

1993-03-01

82

Vapor fraction measurements in a steam-water tube at up to 15 bar using neutron radiography techniques  

Energy Technology Data Exchange (ETDEWEB)

Real time neutron radiography has been used to study the dynamic behavior of two phase flow and measure the time averaged vapor fraction in a heated metal tube containing boiling steam water operating at up to 15 bar pressure. The neutron radiographic technique is non-intrusive and requires no special transparent window region. This is the first time this technique has been used in an electrically heated pressurized flow loop. This unique experimental method offers the opportunity to observe and record on videotape, flow patterns and transient behavior of two phase flow inside opaque containers without disturbing the environment. In this study the test sections consisted of stainless steel tubes with a 1.27 cm outer diameter and wall thicknesses of 0.084 cm and 0.124 cm. The experiments were carried out at the Pennsylvania State University 1 megawatt TRIGA reactor facility utilizing a Precise Optics neutron radiography camera. The inlet ...

1998-02-01

83

Vapor fraction measurements in a steam-water tube at up to 15 bar using neutron radiography techniques  

International Nuclear Information System (INIS)

Real-time neutron radiography has been used to study the dynamic behavior of two-phase flow and measure the time averaged vapor fraction in a heated metal tube containing boiling steam-water operating at up to 15 bar pressure. The neutron radiographic technique is non-intrusive and requires no special transparent window region. This is the first time this technique has been used in an electrically heated pressurized flow loop. This unique experimental method offers the opportunity to observe and record on videotape, flow patterns and transient behavior of two-phase flow inside opaque containers without disturbing the environment. In this study the test sections consisted of stainless steel tubes with a 1.27 cm outer diameter and wall thicknesses of 0.084 and 0.124 cm. The experiments were carried out at the Pennsylvania State University 1 MW TRIGA reactor facility utilizing a Precise Optics neutron radiography camera. The inlet ...

1999-11-03

84

Vapor fraction measurements in a steam-water tube at up to 15 bar using neutron radiography techniques  

International Nuclear Information System (INIS)

Real time neutron radiography has been used to study the dynamic behavior of two phase flow and measure the time averaged vapor fraction in a heated metal tube containing boiling steam water operating at up to 15 bar pressure. The neutron radiographic technique is non-intrusive and requires no special transparent window region. This is the first time this technique has been used in an electrically heated pressurized flow loop. This unique experimental method offers the opportunity to observe and record on videotape, flow patterns and transient behavior of two phase flow inside opaque containers without disturbing the environment. In this study the test sections consisted of stainless steel tubes with a 1.27 cm outer diameter and wall thicknesses of 0.084 cm and 0.124 cm. The experiments were carried out at the Pennsylvania State University 1 megawatt TRIGA reactor facility utilizing a Precise Optics neutron radiography camera. The inlet ...

1998-03-16

85

Nonlinear stability analysis of a reduced order model of nuclear reactors: A parametric study relevant to the advanced heavy water reactor  

International Nuclear Information System (INIS)

Research highlights: ? We model power oscillations in boiling water reactors using a lumped parameter model. ? The nature and amplitudes of oscillations is obtained using a nonlinear analysis. ? The method of multiple scales has been used for the analytical treatment. ? Fuel temperature coefficient of reactivity determines the nature of oscillations. ? The presented systematic method of analysis useful for reduced order reactor models. - Abstract: In this paper, we perform a parametric study of the nonlinear dynamics of a reduced order model for boiling water reactors (BWR) near the Hopf bifurcation point using the method of multiple scales (MMS). Analysis has been performed for general values of the parameters, but the results are demonstrated for parameter values of the model corresponding to the advanced heavy water reactor (AHWR). The neutronics of the AHWR is modeled using point reactor kinetic equations while a ...

2011-01-01

86

Lead uptake and lead loss in the fresh water field crab, Barytelphusa guerini, on exposure to organic and inorganic lead  

Energy Technology Data Exchange (ETDEWEB)

Lead is a heavy metal which is widely used in paint industry, pigments, dyes, electrical components and electronics, plastic chemicals and in various other things. Since some of the lead salts are soluble in water, lead presents a potential threat to aquatic organisms. Studies dealing with invertebrates include those on mortality, growth and lead uptake in Lymnaea palustris and bioaccumulation of heavy metals in oysters and mussels. Little information exists regarding the effect of lead on the fresh water crustaceans. Hence the present investigation has been undertaken to study the uptake and loss of lead on exposure to subtoxic levels or organic and inorganic lead.

1987-07-01

87

Alkylaldehyde-bisulfite adducts as cleavable surfactants  

British Library Electronic Table of Contents (United Kingdom)

Alkylaldehyde-bisulfite adducts with octyl, decyl, and dodecyl groups (CnS: n=8,10,12) were synthesized and the surface-active properties of the water-soluble compounds were compared. Exchange of the counter anions of C10S and C12S from sodium to tetramethylammonium solubilized them in water. The latter ammonium salt (C12S-QA) had surface activities as good as a classical surfactant, sodium dodecylsulfate, and dissociated promptly in weakly basic solution at room temperature to be a non-surfactant. It was also found that C12S-QA solubilized a hydrophobic substrate (solid), N,N-dimethyl-3-nitroaniline, in water and then separated it as a precipitate after alkali treatment.

2007-01-01

88

Conductivity and Viscosity Measurements for Binary Lysozyme Chloride Aqueous Solution and Ternary Lysozyme-Salt-Water Solution  

CERN Document Server

We use the conductimetric method, adequate to electrolytes, to determine the lysozyme charge in lys-water and ternary lys-salt-water systems. We measured also the viscosities for the above binary and ternary systems in the same conditions at pH$=4.5$ and T$=298$ K, measurements that allow us to see any effect of viscosity on cations mobilities and implicitly on the lysozyme charge. The method is illustrated for the lysozyme chloride aqueous solution system at 25$^o$ C, using the data reported here for pH$=4.5$ at 0.15, 0.6, 0.8, 1., 1.5, 2., 2.5, 3., 3.5 mM (mg/mL) lysozyme chloride concentrations. The method was also applied to ternary lys-salt-water systems in the same conditions at pH$=4.5$ and T$=25^o$ C. Ternary conductivities are reported for a mean concentration 0.6 mM of lysozyme chloride in all systems and a mean concentration 0.01, 0.025, 0.05, 0.1, 0.175, 0.2, 0.5, 0.7, 0.9, 1.2, 1.3 and 1.4 M for NaCl; 0.005, ...

2004-01-01

89

Effect of water activity on the lipase catalyzed esterification of geraniol in ionic liquid [bmim]PF6.  

Science.gov (United States)

Enzymatic reactions in non-aqueous media have been shown to be effective in carrying out chemical transformation where the reactants are insoluble in water or water is a byproduct limiting conversion. Ionic liquids, liquid organic salts with infinitesimal vapor pressure, are potentially useful alternatives to organic solvents. It is known that the thermodynamic water activity is an important variable affecting the activity of enzymes in non-aqueous solvents. This study investigated the influence of water activity on the esterification of geraniol with acetic acid in ionic liquid [bmim]PF6 catalyzed by immobilized Candida antarctica lipase B. The conversion of geraniol in [bmim]PF6 was significant although the reaction rate was slower than in organic solvents. The profile of initial reaction rate-water activity was determined experimentally, and differed from the ...

2006-02-01

90

Thermal stability of carnallite under deposit conditions  

Energy Technology Data Exchange (ETDEWEB)

Experimental investigations have been shown that the thermal stability of carnallite shows a clear change to hogher temperature with increasing pressure if the decomposition atmosphere is not removed. Around 40 bar, constitutional water is released from the carnallite lattice at 139/sup 0/C, around 100 bar at 145/sup 0/C. The available temeprature data on thermal release of constitutional water in carnallite (80 to 110/sup 0/C) are not relevant to the possible heat load in a final-storage salt done as all investigations have been carried out in vacuum or in open systems under atmospheric conditions. The author's investigations show the decomposition temeprature of carnallite will be much higher under in-situ conditions with blocked or delayed removal of decomposition atmosphere. However, this applies only to carnallite as isolated mineral phase. Final statements cannot be made until the pressure-temperature ...

1980-12-01

91

Costs for off-site disposal of nonhazardous oil field wastes: Salt caverns versus other disposal methods  

Energy Technology Data Exchange (ETDEWEB)

According to an American Petroleum Institute production waste survey reported on by P.G. Wakim in 1987 and 1988, the exploration and production segment of the US oil and gas industry generated more than 360 million barrels (bbl) of drilling wastes, more than 20 billion bbl of produced water, and nearly 12 million bbl of associated wastes in 1985. Current exploration and production activities are believed to be generating comparable quantities of these oil field wastes. Wakim estimates that 28% of drilling wastes, less than 2% of produced water, and 52% of associated wastes are disposed of in off-site commercial facilities. In recent years, interest in disposing of oil field wastes in solution-mined salt caverns has been growing. This report provides information on the availability of commercial disposal companies in oil-and gas-producing states, the treatment and disposal methods they employ, and the amounts they charge. It ...

1997-09-01

92

Titanate nanotubes as superior adsorbents for removal of lead(II) ions from water  

British Library Electronic Table of Contents (United Kingdom)

Titanate nanotubes were hydrothermally synthesized and their adsorption performances for lead(II) ion removal were studied. The results showed that titanate nanotubes ruptured in the adsorption process resulting in two distinct adsorption stages, thus achieving a maximum adsorption capacity of 3.752mmolg^-^1 of lead(II). Furthermore, it was found that the regeneration of titanate nanotubes loaded with the lead(II) ions can be readily achieved using the saturated EDTA disodium salt aqueous solution, thereby avoiding the trouble of disposal of adsorbent. The adsorption mechanism was also discussed in detail.

2010-01-01

93

Thermally cleavable surfactants  

Energy Technology Data Exchange (ETDEWEB)

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

2009-09-29

94

Thermally cleavable surfactants  

Energy Technology Data Exchange (ETDEWEB)

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

2009-11-24

95

Thermally cleavable surfactants  

Energy Technology Data Exchange (ETDEWEB)

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments and the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

2006-04-04

96

Stress corrosion cracking susceptibility of #beta# titanium alloy 38-6-44  

International Nuclear Information System (INIS)

The threshold stress intensities for stress corrosion crack propagation in beta titanium alloy 38-6-44, Ti3Al-8V-6Cr-4Mo-4Zr, has been determined in salt water and methanolic solutions. The alloy was immune to stress corrosion cracking (SCC) in aqueous sodium chloride solutions (marine atmosphere). However, in methanolic solutions, the alloy was very susceptible to SCC. This marked susceptibility in methanolic solutions can be mitigated by the addition of an inhibitor: sodium nitrate. Crack extension in the alloy was transgranular and failure occurred by brittle quasi-cleavage in methanolic solutions.

97

Ion-Specific Hydration Effects: Extending the Poisson-Boltzmann Theory  

CERN Document Server

In aqueous solutions, dissolved ions interact strongly with the surrounding water, thereby modifying the solution properties in an ion-specific manner. These ion-hydration interactions can be accounted for theoretically on a mean-field level by including phenomenological terms in the free energy that correspond to the most dominant ion-specific interactions. Minimizing this free energy leads to modified Poisson-Boltzmann equations with appropriate boundary conditions. Here, we review how this strategy has been used to predict some of the ways ion-specific effects can modify the forces acting within and between charged interfaces immersed in salt solutions.

2011-01-01

98

Aqueous drilling fluids containing fluid loss additives  

Energy Technology Data Exchange (ETDEWEB)

This patent describes an aqueous clay containing drilling fluid having present in an amount sufficient to reduce fluid loss of the drilling fluid, a copolymer of (1) from about 80% to about 98% by weight of acrylic acid and (2) from about 2% to about 20% by weight of itaconic acid. The copolymer has a weight average molecular weight of between about 50,000 to about 1,000,000, being in its free acid or partially or completely neutralized salt form and being at least water dispersible.

1987-03-03

100

Regulation of agricultural drainage to San Joaquin River  

Science.gov (United States)

A technical committee reported on: (1) proposed water quality objectives for the San Joaquin River Basin; (2) proposed effluent limitations for agricultural drainage discharges in the basin to achieve these objectives; and (3) a proposal to regulate these discharges. The costs and economic impact of achieving various alternative water quality objectives were also evaluated. The information gathered by the technical committee will be used by the Regional Board along with other information in their review of the San Joaquin River Basin Water Quality Control Plan and their actions to regulate agricultural drainage in the San Joaquin Valley. The results of the Technical Committee's efforts as reported in Regulation of Agricultural Drainage to the San Joaquin River, August 1987. Based on the available information, the improvement in water quality resulting from implementation of the interim selenium ...

1989-02-01

101

Influence of fly ash on soil physical properties and turfgrass establishment  

Energy Technology Data Exchange (ETDEWEB)

A field study (1993-96) assessed the benefits of applying unusually high rates of coal fly ash from power plants as a soil amendment to enhance water retention of soils without adversely affecting growth and marketability of the turf species, centipedegrass (Eremochloa ophiuroides (Munro) Hack.) A Latin Square plot design was employed that included 0 (control, no fly ash applied), 280, 560 and 1120 MgHa {sup -1} application rates of unweathered precipitator fly ash. The fly ash was spread evenly over each plot area, rototilled, and allowed to weather under natural conditions for 8 months before seeding. High levels of soluble salts, indicated by the electrical conductivity of soil extracts, in tandem with an apparent phytotoxic effect from boron, apparently inhibited initial plant establishment as shown by substantially lower germination counts in treated soil. However, plant height and rooting depth were not adversely affected, as were the dry ...

2001-04-01

102

The volumetric and thermochemical properties of Y(ClO_4)_3 (aq), Yb(ClO_4)_3 (aq), Dy(ClO_4)_3 (aq), and Sm(ClO_4)_3 (aq) at T=(288.15,298.15,313.15, and 328.15) K and p=0.1 MPa  

International Nuclear Information System (INIS)

Relative densities and relative massic heat capacities have been measured for aqueous solutions of Y(ClO_4)_3, Yb(ClO_4)_3, Dy(ClO_4)_3, and Sm(ClO_4)_3 at T=(288.15,298.15,313.15, and 328.15) K and p=0.1 MPa. These measurements were made in the concentration range 0.01624#<=#m/(mol#centre dot#kg"-"1)#<=#0.41822 using a Sodev 02D Vibrating Tube Densimeter and a Picker Microflow Calorimeter, respectively. To counter the potential effects of hydrolysis, aqueous solutions of the investigated salts were acidified with perchloric acid. After correcting for the presence of the acid, the measured properties were used to calculate apparent molar volumes and apparent molar heat capacities for solutions of the perchlorate salts in water. The calculated apparent molar properties were modeled at each investigated temperature using Pitzer ion interaction equations to produce estimates of apparent molar volumes and heat capacities ...

2003-05-01

103

Geochemical History of the Dead Sea  

British Library Electronic Table of Contents (United Kingdom)

Graphical Abstract A Southward view of the Dead Sea western coast. The steep western escarpment of the Dead Sea basin, composed mainly of Upper Cretaceous limestone and dolomite, can be seen on the right. Beach terraces left by the shrinking lake run parallel to the shore. The larger part of the area between the present water line and the mountains was still under Dead Sea water just 50?60?years ago. The current fall of the lake?s stand is around 1?m?year?1. Three on-shore sinkholes can be seen in the front of the photo, as well as two submerged ones near its lower left corner. These were caused by dissolution of a Holocene salt layer located tens of meters below the surface, resulting in the collapse of the overlying sediments. The retreat of the Dead Sea in recent years was followed by e...

2009-01-01

104

Beverage iodine levels in Germany  

British Library Electronic Table of Contents (United Kingdom)

Sales of iodized table salt (household use, bulk containers) have been flat in Germany since 1996/1997. Nevertheless, the amount of iodide excreted with the urine has been steadily increasing in the German population since 1993. We investigated the beverage iodine levels as possible source of the increased input of iodine into the food chain. No systematic studies on this topic have yet been carried out in Germany. A total of 510 samples were drawn from large grocery discounters who supply all German states with their products (35% fruit and vegetable juices, 35% beers, 10% pooled milk and yoghurt drinks, 10% mineral water, 10% soda). (1) Water-based beverage samples are prepared by solid-phase extraction and iodine concentration is determined by HPLC and electrochemical detection, (2) the...

2009-01-01

105

A system for distributed intrusion detection  

Energy Technology Data Exchange (ETDEWEB)

The study of providing security in computer networks is a rapidly growing area of interest because the network is the medium over which most attacks or intrusions on computer systems are launched. One approach to solving this problem is the intrusion-detection concept, whose basic premise is that not only abandoning the existing and huge infrastructure of possibly-insecure computer and network systems is impossible, but also replacing them by totally-secure systems may not be feasible or cost effective. Previous work on intrusion-detection systems were performed on stand-alone hosts and on a broadcast local area network (LAN) environment. The focus of our present research is to extend our network intrusion-detection concept from the LAN environment to arbitarily wider areas with the network topology being arbitrary as well. The generalized distributed environment is heterogeneous, i.e., the network ...

1991-01-01

106

Network Security Alerts Management Architecture for Signature-Based Intrusions Detection Systems within a NAT Environment  

British Library Electronic Table of Contents (United Kingdom)

Internet is providing essential communication between an infinite number of people and is being increasingly used as a tool for commerce. At the same time, security is becoming a tremendously important issue to deal with. Different network security solutions exist and contribute to enhanced security. From these solutions, Intrusion detection systems (IDS) have become one of the most common countermeasures for monitoring safety in computer systems and networks. The purpose of IDSs is distinguishing between intruders and normal users. However, IDSs report a massive number of isolated alerts. These isolated alerts represent low-level security-related events. Many of these isolated alerts are logically involved in a single multi-stage intrusion incident and a security officer often wants to an...

2011-01-01

107

Formation and stabilization of anionic metal complexes in concentrated aqueous quaternary ammonium salt solutions  

Energy Technology Data Exchange (ETDEWEB)

Anionic complexes of transition metals were stabilized in aqueous solutions containing high concentrations of various short-chain quaternary ammonium salts. Compounds with longer paraffin chains were effective in much less concentrated solution. Complex ions were detected spectrophotometrically. FeCl/sub 4//sup -/, which is usually formed in concentrated HCl, was the predominant Fe(III) complex in 30 m choline chloride containing only 0.12 M HCl. A yellow transitory Tc(VII) chloro-addition intermediate, formed in the reduction of TcO/sub 4//sup -/ by concentrated HCl, was stabilized when the solution also contained 25 m choline chloride. Its spectrum, as well as the isolation of an already known Tc(VII) bipyridyl complex, is reported. Concentrated organic electrolytes also stabilized Tc(V) oxide halides against disproportionation and Tc(IV) hexahalides against hydrolysis. Halochromates of Cr(VI) were formed and stabilized in dilute acid containing quaternary ...

1985-02-04

108

Micropolarities of lipid bilayers and micelles. 3. Effect of monovalent ions on the dielectric constant of the water-membrane interface of unilamellar phosphatidylcholine vesicles  

Energy Technology Data Exchange (ETDEWEB)

A study was undertaken of the effect of monovalent cations (Li/sup +/, Na/sup +/, K/sup +/) on the dielectric constant (epsilon) of the water-lipid interface of unilamellar phosphatidylcholine (PC) vesicles, i.e., the ester carbonyl oxygen region of the PC molecules or the neighborhood of the oxygen atoms of the phosphorylcholine moiety. epsilon was determined by reacting the free radical 1,1-diphenyl-2-picrylhydrazyl with ..cap alpha..-tocopherol incorporated in the lipid vesicles. The results are consistent with a decrease of epsilon (LiCl: 35.5 to 29.5; NaCl: 34 to 29; KCl: 33 to 29) as the concentration of the salts in the solvent media increases from 0.025 to 0.5 M. These effects can be rationalized in terms of dielectric saturation at the water-lipid interface brought about by ion-induced local electric fields. In the unilamellar PC vesicles the effect of the ions on epsilon follows the sequence K/sup +/ > Na/sup ...

1986-02-27

109

Extension of the EQ3/6 computer codes to geochemical modeling of brines  

Energy Technology Data Exchange (ETDEWEB)

Recent modifications to the EQ3/6 geochemical modeling software package provide for the use of Pitzer's equations to calculate the activity coefficients of aqueous species and the activity of water. These changes extend the range of solute concentrations over which the codes can be used to dependably calculate equilibria in geochemical systems, and permit the inclusion of ion pairs, complexes, and undissociated acids and bases as explicit component species in the Pitzer model. Comparisons of calculations made by the EQ3NR and EQ6 compuer codes with experimental data confirm that the modifications not only allow the codes to accurately evaluate activity coefficients in concentrated solutions, but also permit prediction of solubility limits of evaporite minerals in brines at 25/sup 0/C and elevated temperatures. Calculations for a few salts can be made at temperatures up to approx. 300/sup 0/C, but the temperature range for most ...

1984-10-23

110

Mass transfer model for two-layer TBP oxidation reactions  

Energy Technology Data Exchange (ETDEWEB)

To prove that two-layer, TBP-nitric acid mixtures can be safely stored in the canyon evaporators, it must be demonstrated that a runaway reaction between TBP and nitric acid will not occur. Previous bench-scale experiments showed that, at typical evaporator temperatures, this reaction is endothermic and therefore cannot run away, due to the loss of heat from evaporation of water in the organic layer. However, the reaction would be exothermic and could run away if the small amount of water in the organic layer evaporates before the nitric acid in this layer is consumed by the reaction. Provided that there is enough water in the aqueous layer, this would occur if the organic layer is sufficiently thick so that the rate of loss of water by evaporation exceeds the rate of replenishment due to mixing with the aqueous layer. This report presents measurements of mass transfer rates for the mixing of ...

1994-09-28

111

A field demonstration of the microbial treatment of sour produced water  

Energy Technology Data Exchange (ETDEWEB)

The potential for detoxification and deodorization of sulfide-laden water (sour water) by microbial treatment was evaluated at a petroleum production site under field conditions. A sulfide-tolerant strain of the chemautotroph and facultative anaerobe, Thiobacillus denitrificans, was introduced into an oil-skimming pit of the Amoco Production Company LACT 10 Unit of the Salt Creek Field, Wyoming. Field-produced water enters this pit from the oil/water separation treatment train at an average flowrate of 5,000 bbl/D (795 m{sup 3}/D) with a potential maximum of 98,000 bbl/D (15,580 m{sup 3}/D). Water conditions at the pit inlet are 4,800 mg/l TDS, 100 mg/l sulfide, pH 7.8, and 107{degrees}F. To this water an aqueous solution of ammonium nitrate and diphosphorous pentoxide was added to provide required nutrients for the bacteria. The first 20% ...

1995-12-31

112

Study of superficial films and of electrochemical behaviour of some nickel base alloys and titanium base alloys in solution representation of granitic, argillaceous and salted ground waters  

Energy Technology Data Exchange (ETDEWEB)

The corrosion behaviour of the stainless steels 304, 316 Ti, 25Cr-20Ni-Mo-Ti, nickel base alloys Hastelloy C4, Inconel 625, Incoloy 800, Ti and Ti-0.2% Pd alloy has been studied in the aerated or deaerated solutions at 20/sup 0/C and 90/sup 0/C whose compositions are representative of interstitial ground waters: granitic or clay waters or salt brine. The electrochemical techniques used are voltametry, polarization resistance and complexe impedance measurements. Electrochemical data show the respective influence of the parameters such as temperature, solution composition and dissolved oxygen, addition of soluble species chloride, fluoride, sulfide and carbonates, on which depend the corrosion current density, the passivation and the pitting potential. The inhibition efficiency of carbonate and bicarbonate activities against pitting corrosion is determined. In clay water at 90/sup 0/C, Ti and Ti-Pd show ...

1985-01-01

113

Performance assessment for the disposal of low-level waste in the 200 east area burial grounds  

Energy Technology Data Exchange (ETDEWEB)

A performance assessment analysis was completed for the 200 East Area Low-Level Burial Grounds (LLBG) to satisfy compliance requirements in DOE Order 5820.2A. In the analysis, scenarios of radionuclide release from the 200 East Area Low-Level waste facility was evaluated. The analysis focused on two primary scenarios leading to exposure. The first was inadvertent intrusion. In this scenario, it was assumed that institutional control of the site and knowledge of the disposal facility has been lost. Waste is subsequently exhumed and dose from exposure is received. The second scenario was groundwater contamination.In this scenario, radionuclides are leached from the waste by infiltrating precipitation and transported through the soil column to the underlying unconfined aquifer. The contaminated water is pumped from a well 100 m downstream and consumed,causing dose. Estimates of potential contamination of the surrounding environment were developed ...

1996-08-15

114

Late Archean intrusive charnockites from the west-central Wind River Mountains, Wyoming  

Energy Technology Data Exchange (ETDEWEB)

Late Archean (ca. 2.5Ga) porphyritic granites to comprise about 25% of the crystalline rocks of the Wind River uplift. In most localities, they are typical biotite-hornblende granites but on the western margin of the range there is evidence that portions of at least one pluton were emplaced as charnockite. In the Burnt Lake area homogenous charnockite crops out over an area of at least 3km while in the Boulder Creek Canyon, 8km to the S.E. charnockite occurs locally as blotches in porphyritic biotite granite. One sample from Boulder Creek, 15 cm in the longest dimension, shows a complete transition from charnockite to biotite granite. Textures indicate that the transition occurred as subsolidus hydration, with hornblende and biotite replacing augite and orthopyroxene, respectively. Pryoxene geothermometry from this sample yields maximum temperatures of around 900/sup 0/C, with a cooling trend to 600/sup 0/. Fluid inclusion of both CO/sub 2/ (p = .85 to .95) and H/sub 2/O (rho = .8 - ...

1985-01-01

115

Development of a tool to collect insulation oil in a cable connection box without interrupting power supply; Muteiden ni yoru cable setsuzokubakonai zetsuen`yu saishu kogu no kaihatsu  

Energy Technology Data Exchange (ETDEWEB)

While underground power transmission lines have become to use CV cables as the mainstream, existing facilities still use OF cables. Factors of OF cable deterioration include heat cycles during operation and surge intrusion. As a method to diagnose this deterioration in insulation, characteristics tests are performed by collecting insulation oil in a cable connection box. The insulation oil collection work has been done conventionally with the power line stopped to prevent danger from induction voltage. A power uninterruptible oil collection tool was developed recently. The tool consists mainly of an insulator made of epoxy resin, wherein a connection box connector is rotated and loosened by operating an insulating operation rod, with the structure not contacted directly with metallic sheath, so that insulation oil can go through the oil collecting tool and gets collected. Discussions were given on the tool to be capable of collecting samples for analyzing ...

1999-02-10

116

Ten-nanometer surface intrusions in room temperature silicon  

CERN Document Server

Defects ~10 nm in size, with number densities ~10^{10} cm^{-2}, form spontaneously beneath ion-milled, etched, or HF-dipped silicon surfaces examined in our Ti-ion getter-pumped transmission electron microscope (TEM) after exposure to air. They appear as weakly-strained non-crystalline intrusions into silicon bulk, that show up best in the TEM under conditions of strong edge or bend contrast. If ambient air exposure is <10 minutes, defect nucleation and growth can be monitored {\\em in situ}. Possible mechanisms of formation are discussed.

2002-01-01

117

Sustainable water resources management in Pakistan  

International Nuclear Information System (INIS)

Total river discharge in Pakistan in summer season vary from 3 thousand to 34 thousand cusses (100 thousand Cusses to 1,200 thousand Cusses) and can cause tremendous loss to human lives, crops and property, this causes the loss of most of the flood water in the lower Indus plains to the sea. Due to limited capacity of storage at Tarbela and Mangla Dams on river Indus and Jhelum, with virtually no control on Chenab, Ravi and Sutlej, devastating problems are faced between July and October in the event of excessive rainfall in the catchments. Due to enormous amounts of sediments brought in by the feeding rivers, the three major reservoirs -Tarbela, Mangla and Chashma will lose their storage capacity, by 25 % by the end of the year 2010, which will further aggravate the water-availability situation in Pakistan. The quality of water is also deteriorating due to urbanization and industrialization and agricultural developments. On ...

2004-06-07

118

Modeling of hydrologic conditions and solute movement in processed oil shale waste embankments under simulated climatic conditions  

Energy Technology Data Exchange (ETDEWEB)

Commercial development of oil shale resources will produce vast quantities of processed shale waste. The presence of potentially toxic trace elements, inorganic salts, and potentially toxic residual organic constitutents make the disposal of vast quantities of processed shale a potential environmental problem. To be environmentally acceptable, processed shale disposal must: result in a physically stable structure, prevent or minimize release of potentially toxic compounds, and provide an economically acceptable post-land use. Water is the common element underlying all factors important to the environmental stability of disposed solid waste. The leaching and transport of solubles by water in processed shale embankments may result in degradation of local surface and groundwater quality. The major purpose of this research is to physically model, study, and describe the redistribution and movement of water ...

1990-07-01

119

Experience on resin pyrolysis  

International Nuclear Information System (INIS)

The Swedish State Power Board has together with Nukem, Hanau, West-Germany carried out pyrolysis o powder resins in a pilot plant with a capacity of about 30 kg/hr. The pyrolysis reactor with its afterburner and offgas scrubber system has been operated under steady state condition. About 2200 kg resins have been pyrolysed under November-December 1983 and the decontamination factor for Cs has been measured. Solidification of the residues from the pyrolysis reactor and scrubber water solutions has been carried out and various recipes with cement have been tested. The pyrolysis process has high decontamination factors and no offgas problems as the operating temperature of the reactor is Low. The residues from the reactor are chemically dead and can not cause swelling problems. Compared with a normal cementation process the final waste volume will be reduced with a factor of 4 if also the scrubber water after neutralization is solidified. The ...

120

A new porous-layer activated-charcoal-coated fused silica fiber: application for determination of BTEX compounds in water samples using headspace solid-phase microextraction and capillary gas chromatography  

Energy Technology Data Exchange (ETDEWEB)

Extra-fine powdered activated charcoal has been used as stationary phase (coating layer) in solid-phase microextraction (SPME). The efficiency and reliability of the prepared device have been investigated for the extraction of some volatile organic compounds such as benzene, toluene, ethylbenzene and xylene isomers (BTEX) from the headspace of water samples. Monitoring of the extracted compounds and further quantitative analysis of the real samples have been performed by capillary GC-FID. Effects of several factors such as temperature, addition of salt, and stirring speed on extraction efficiency and exposure time have been studied. Under optimum conditions, extraction recoveries for these compounds from 50 mL water were >95%. The calibration graphs were linear in the range 5 to 10{sup 4} pg mL{sup -1} and the detection limit for each BTEX compound was 1.5-2 pg mL{sup -1}. The results obtained by use of this porous layer ...

1997-12-31

121

Role of bile salt in regulating Mcl-1 phosphorylation and chemoresistance in hepatocellular carcinoma cells  

UK PubMed Central (United Kingdom)

BackgroundGlycochenodeoxycholate (GCDA) is one of the major human bile salts. Bile salts stimulate cell survival and proliferation through the mitogen-activated protein kinase, but...Full Text Available

122

Patch Clamp Studies on Root Cell Vacuoles of a Salt-Tolerant and a Salt-Sensitive Plantago Species 1  

UK PubMed Central (United Kingdom)

Plantago media L. and Plantago maritima L. differ in their strategy toward salt stress, a major difference being the uptake and distribution of ions. Patch clamp techniques...Full Text Available

1990-01-01

123

Solar energy desalination for arid coastal regions: development of a humidification-dehumidification seawater greenhouse  

Energy Technology Data Exchange (ETDEWEB)

The long-term aim of our research is to develop humidification-dehumidification desalination technology for farms in arid coastal regions that are suffering from salt-infected soils and shortages of potable groundwater. The specific aim of our current study was to determine the influence of greenhouse-related parameters on a process, called Seawater Greenhouse, which combines fresh water production with growth of crops in a greenhouse system. A thermodynamic model was used based on heat and mass balances. The dimension of the greenhouse had the greatest overall effect on the water production and energy consumption. A wide shallow greenhouse, 200 m wide by 50 m deep gave 125 m{sup 3} d{sup -1} of fresh water. This was greater than a factor of two compared to the worst-case scenario with the same area (50 m wide by 200 m deep), which gave 58 m{sup 3} d{sup -1}. Low power consumption went hand-in-hand with ...

2003-11-01

124

Study on polyamide thin-film composite nanofiltration membrane by interfacial polymerization of polyvinylamine (PVAm) and isophthaloyl chloride (IPC)  

British Library Electronic Table of Contents (United Kingdom)

A novel thin-film composite polyamide nanofiltration membrane was prepared through interfacial polymerization of polymeric polyamine polyvinylamine (PVAm) with isophthaloyl chloride (IPC) on a polysulfone supporting film. The composite membranes were prepared under different conditions and characterized in terms of chemical and morphological structures, surface zeta potential, pure water permeability, and rejection to different solutes including electrolytes and sucrose. The results showed that the membrane performance was significantly affected by the content of amine units of PVAm and the concentrations of PVAm and IPC. The increase of the content of amine units of PVAm and the concentration of IPC resulted in an augment in salt rejection and a decrease in permeability, while the increas...

2011-01-01

125

Redox conditions and heavy metals distribution in mangrove forests receiving effluents from shrimp farms (Teremba Bay, New Caledonia)  

British Library Electronic Table of Contents (United Kingdom)

Purpose The mangroves of New Caledonia, in the south Pacific, act as a buffer between a lagoon of more than 20,000?km2 and the island, which is characterized by ultramafic rocks and lateritic soils that are exploited for their richness in heavy metals. We will provide a better understanding of the redox conditions, and of heavy metal distributions in mangroves receiving shrimp farm effluents. Materials and methods Samples were collected from four areas defined in terms of vegetation composition: a salt flat, an Avicennia marina forest, in which effluents are released; a Rhizophora stylosa forest, and a dead Rhizophora forest. They were collected during times of maximum effluent release. Some measurements on pore water were also done during a period without effluent. Cores (70?cm deep) were...

2011-01-01

126

Preparation and evaluation of a novel glass-ionomer cement with antibacterial functions  

British Library Electronic Table of Contents (United Kingdom)

Objective.The objective of this study was to use the newly synthesized poly(quaternary ammonium salt) (PQAS)-containing polyacid to formulate the light-curable glass-ionomer cements and study the effect of the PQAS on the compressive strength and antibacterial activity of the formed cements.Materials and methods.The functional QAS and their constructed PQAS were synthesized, characterized and formulated into the experimental high-strength cements. Compressive strength (CS) and Streptococcus mutans viability were used to evaluate the mechanical strength and antibacterial activity of the cements. Fuji II LC cement was used as control. The specimens were conditioned in distilled water at 37 degrees C for 24 h prior to testing. The effects of the substitute chain length, loading as well as gra...

2011-01-01

127

K S Krishnan and the early experimental evidences for the Jahn-Teller Theorem  

CERN Document Server

Jahn-Teller theorem, proposed in 1937, predicts a distortional instability for a molecule that has symmetry based degenerate electronic states. In 1939 Krishnan emphasized the importance of this theorem for the arrangement of water molecules around the transition metal or rare earth ions in aqueous solutions and hydrated saltes, in a short and interesting paper published in Nature by pointing out atleast four existing experimental results in support of the theorem. This paper of Krishnan has remained essentially unknown to the practitioners of Jahn-Teller effect, eventhough it pointed to the best experimental results that were available, in the 30's and 40's, in support of Jahn-Teller theorem. Some of the modern day experiments are also in conformity with some specific suggestions of Krishnan.

1998-01-01

128

Investigation and analytical use of rare earth ionic associates with benzilic acid and rhodamine B  

International Nuclear Information System (INIS)

Ions of rare earth elements (r.e.e.) have been found to form with benzilic acid and rhodamine B precipitates hardly soluble in water and extractable by toluene. The conditions of La and Pr determination by extraction-spectrophotometry method are studied. Relative square deviation does not exceed 0.027 and 0.034 respectively. The method can be used for determination of other cerium sub-group r.e.e. in their salts and cannot be employed for determination of lighter r.e.e. in the presence of heavier r.e.e., because the latter form low soluble precipitates capturing the r.e.e. situated in the beginninq of the r.e.e. series.

1977-01-01

129

Controlled Synthesis of Water-Dispersible Faceted Crystalline Copper Nanoparticles and Their Catalytic Properties  

British Library Electronic Table of Contents (United Kingdom)

We report a solution-phase synthetic route to copper nanoparticles with controllable size and shape. The synthesis of the nanoparticles is achieved by the reduction of copper(II) salt in aqueous solution with hydrazine under air atmosphere in the presence of poly(acrylic acid) (PAA) as capping agent. The results suggest that the pH plays a key role for the formation of pure copper nanoparticles, whereas the concentration of PAA is important for controlling the size and geometric shape of the nanoparticles. The average size of the copper nanoparticles can be varied from 30 to 80 nm, depending on the concentration of PAA. With a moderate amount of PAA, faceted crystalline copper nanoparticles are obtained. The as-synthesized copper nanoparticles appear red in color and are stable for weeks, ...

2010-01-01

130

A new approach to the isolation and characterization of wheat flour allergens  

British Library Electronic Table of Contents (United Kingdom)

Summary Background The incidence of food allergy to wheat is increasing. Its diagnosis depends on the purity of major allergens and their inclusion in tests. Isolation and characterization of wheat allergens are therefore of utmost importance. Objective To purify and identify wheat flour allergens most frequently recognized by patients' IgE antibodies and to study their allergenicity. Methods Water/salt-soluble extracts from wheat flour were prepared and separated using a combination of ultrafiltration, isoelectric focusing and liquid chromatography. Purified proteins were analysed by immunoblotting using pooled sera from patients with atopic dermatitis who possessed IgE specific to wheat. Wheat proteins found to bind IgE were subsequently identified by matrix-assisted laser desorption/ion...

2011-01-01

131

Mass transfer model for two-layer TBP oxidation reactions: Revision 1  

Energy Technology Data Exchange (ETDEWEB)

To prove that two-layer, TBP-nitric acid mixtures can be safely stored in the Canyon evaporators, it must be demonstrated that a runaway reaction between TBP and nitric acid will not occur. Previous bench-scale experiments showed that, at typical evaporator temperatures, this reaction is endothermic and therefore cannot run away, due to the loss of heat from evaporation of water in the organic layer. However, the reaction would be exothermic and could run away if the small amount of water in the organic layer evaporates before the nitric acid in this layer is consumed by the reaction. Provided that there is enough water in the aqueous layer, this would occur if the organic layer is sufficiently thick so that the rate of loss of water by evaporation exceeds the rate of replenishment due to mixing with the aqueous layer. Bubbles containing reaction products enhance the rate of transfer of ...

1994-11-04

132

Aerosol composition, chemistry, and source characterization during the 2008 VOCALS Experiment  

Energy Technology Data Exchange (ETDEWEB)

Chemical composition of fine aerosol particles over the northern Chilean coastal waters was determined onboard the U.S. DOE G-1 aircraft during the VOCALS (VAMOS Ocean-Cloud-Atmosphere-Land Study) field campaign between October 16 and November 15, 2008. SO42-, NO3-, NH4+, and total organics (Org) were determined using an Aerodyne Aerosol Mass Spectrometer, and SO42-, NO3-, NH4+, Na+, Cl-, CH3SO3-, Mg2+, Ca2+, and K+ were determined using a particle-into-liquid sampler-ion chromatography technique. The results show the marine boundary layer (MBL) aerosol mass was dominated by non- sea-salt SO42- followed by Na+, Cl-, Org, NO3-, and NH4+, in decreasing importance; CH3SO3-, Ca2+, and K+ rarely exceeded their respective limits of detection. The SO42- aerosols were strongly acidic as the equivalent NH4+ to SO42- ratio was only ~0.25 on average. NaCl particles, presumably of sea-salt origin, showed chloride deficits but retained ...

2010-03-15

133

Degradation of malathion by salt-marsh microorganisms.  

UK PubMed Central (United Kingdom)

Numerous bacteria from a salt-marsh environment are capable of degrading malathion, an organophosphate insecticide, when supplied with additional nutrients as energy and carbon sources. Seven isolates...Full Text Available

1977-02-01

134

Bitumen immobilization of aqueous radwaste by thin-film evaporation  

International Nuclear Information System (INIS)

In the early 1980s, AECL built a Waste Treatment Centre (WTC) for managing low-level solid and aqueous liquid wastes for converting CANDU wastes. At present, two liquid waste streams are being treated at the WTC. The liquid waste streams are volume-reduced by a combination of continuous crossflow microfiltration (MF), spiral wound reverse osmosis (SWRO) and tubular reverse osmosis (TRO) membrane technologies. The concentrate produced from the TRO system and the volume-reduced MF backwash solutions are evaporated while simultaneously adding bitumen in a thin-film evaporator. A water-free product of chemical and radiochemical salts and bitumen is removed in 200-L galvanized steel drums for storage. The radiation field of product drums on contact typically has a value of 0.5 to 3 R/h depending upon the feed concentration of radioactivity to the evaporator. The total solids content in the 200-L drum ranges from 25 to 35%. Encapsulated in the ...

1996-02-25

135

Water-soluble cis-[(NHC)PdBr2(TPPTS)] catalysts and their applications in Suzuki-Miyaura coupling of aryl chlorides  

British Library Electronic Table of Contents (United Kingdom)

New palladium(II) complexes (2), bearing NHC/TPPTS ligands, (NHC=benzimidazol-2-ylidene; TPPTS=triphenylphosphine-3,3',3''-trisulfonic acid trisodium salt) have been prepared and characterized by elemental analyses and spectroscopic methods. Their ability to catalyze the Suzuki-Miyaura reaction in neat water has been studied at 100^oC. Very high activities have been observed in the coupling of phenylboronic acid with aryl chlorides in the presence of 1% of the catalyst. We have compared the electronic properties of cis-[PdBr2(NHC)(TPPTS)] with the related complexes, [PdX2(NHC)]2 and [trans-PdBr2(NHC)(pdca)] (pdca=pyridine-2,6-dicarboxyic acid) (3) via three different techniques: cyclic voltammetry, thermogravimetric analysis and ^1^3C NMR spectroscopy.

2011-01-01

136

Solidification of DOE problem wastes  

Energy Technology Data Exchange (ETDEWEB)

Sodium nitrate waste has been successfully solidified in two types of polymeric materials: polyethylene, a thermoplastic material, and polyester styrene (PES), a thermosetting material. Waste form property evaluation tests such as ANS 16.1 leaching test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. A single-screw extruder was employed for incorporating dry waste into polyethylene at its melt temperature of 120/sup 0/C to produce a homogenous mixture. Results of the leaching test for polyethylene waste forms containing 30, 50, 60 and 70 wt% sodium nitrate are presented as cumulative fraction leached and leaching indices ranging from 11 to 7.8. Two PES systems are discussed. The first is for solidification of dry salt wastes and the second is a water extendible system that is compatible with wet waste streams. Leaching data for PES and water extendible ...

1986-01-01

137

Operating experience with solidification of radioactive waste by a thin-film evaporator  

Energy Technology Data Exchange (ETDEWEB)

In the nuclear power stations of GDR the rough radioactive waste includes borat-containing evaporator bottoms and spent ion exchanger resins. For its final disposal in deep geological formations (rock salt mines) this waste has to be solidified. The experience of one year lasting operation of a steam heated thin-film evaporator (heating surface 2 m{sup 3}) for evaporator bottoms to be solidified with a solid content of 200-250 g/l are reported on. In short time such amount of water is abstracted from the rough waste that due to the borate content a hot high-viscous product passes from evaporator to waste drum and there solidifies like glass to monolith. The product quality depends on the adjustment of the flow-equilibrium in the evaporator. Boric acid is used as matrix for the radioactive residues. The residual water content of the solidified waste product was about 15-20%, the volume reduction was V{sub f}=5...6. In order ...

1990-01-01

138

Operating experience with solidification of radioactive waste by a thin-film evaporator  

International Nuclear Information System (INIS)

In the nuclear power stations of GDR the rough radioactive waste includes borat-containing evaporator bottoms and spent ion exchanger resins. For its final disposal in deep geological formations (rock salt mines) this waste has to be solidified. The experience of one year lasting operation of a steam heated thin-film evaporator (heating surface 2 m"3) for evaporator bottoms to be solidified with a solid content of 200-250 g/l are reported on. In short time such amount of water is abstracted from the rough waste that due to the borate content a hot high-viscous product passes from evaporator to waste drum and there solidifies like glass to monolith. The product quality depends on the adjustment of the flow-equilibrium in the evaporator. Boric acid is used as matrix for the radioactive residues. The residual water content of the solidified waste product was about 15-20%, the volume reduction was V_f=5...6. In order to be sure ...

1990-06-01

139

Nature of arrangement of buried reefs and bioherms in the Lower Permian deposits of the Dnieper Donets Basin  

Energy Technology Data Exchange (ETDEWEB)

In the Assel'skiy and Sakmarskiy time of the lower Permian epoch, on the territory of the modern Dnieper and Donets, and Pripyatskiy Basins, there was a gulf which stretched in a northwest direction. The latter connected to the open sea in the east through the CisDonets trough. Transverse tectonic elevations divided the gulf into 5 semi-isolated reservoirs. In the Assel'skiy time, in the period of carbonate sedimentation, the development of algae, crinoids, corals and other organisms occurred. They created reef, bioherm and biostroma reconstructions. The most favorable sections for their settlement were the coastal zones of the gulf, consedimentation positive structures and transverse tectonic elevations. It is assumed that the formation of reefs, bioherms and biostromas, on the one hand, and sedimentation of evaporites on the other hand, are interrelated processes. The first after the next marine transgression during their growth was a greater impairment to the ...

1981-01-01

145

Investigation of the evaporation of rare earth chlorides in a LiCl-KCl molten salt  

International Nuclear Information System (INIS)

Uranium dendrites which were deposited at a solid cathode of an electrorefiner contained a certain amount of salts. These salts should be removed for the recovery of pure metal using a cathode processor. In the uranium deposits from the electrorefining process, there are actinide chlorides and rare earth chlorides in addition to uranium chloride in the LiCl-KCl eutectic salt. The evaporation behaviors of the actinides and rare earth chlorides in the salts should be investigated for the removal of salts in the deposits. Experiments on the salt evaporation of rare earth chlorides in a LiCl-KCl eutectic salt were carried out. Though the vapor pressures of the rare earth chlorides were lower than those of the LiCl and KCl, the rare earth chlorides were co-evaporized with the LiCl-KCl eutectic salt. The Hertz-Langmuir ...

2011-02-01

146

Compaction of salt by means of explosives  

Energy Technology Data Exchange (ETDEWEB)

One of the concerns with locating radioactive waste storage sites in salt deposits is how to permanently seal the underground storage areas once they have reached their storage capacity. The compaction of salt using explosives has been identified as a potential method of producing permanent seals in both entryways and shafts to storage areas. This paper describes the test procedure and results of a preliminary investigation to determine the feasibility of utilizing explosives in the compaction of salt. Three simple tests were carried out to measure the degree to which loose salt could be compacted.

1996-12-01

147

Characterization of Metal Oxide and Silica-Based Electrodes  

Energy Technology Data Exchange (ETDEWEB)

Objective of the project is characterization of electrode reactions in molten salt by using metal oxides and silica-based electrode. The scope of project are characterization of metal oxide properties in molten salt and miniaturization of 3-electrode electrochemical test cell. Electrochemical micro-cell for actinide-LiCl-KCl molten salt was newly designed. Electroless and electrochemical deposition technique was applied to Mo coating on quartz tube. From the design of electrode and 3-electrode electrochemical cell suitable for the tests in molten salt electrolyte, so it is anticipated to get the information on the electrochemical behavior of metallic electrode in molten salt and to secure the information on oxidation/reduction behavior of actinide

2010-05-15

148

Rb-Sr ages and palaeomagnetic data for some Angolan alkaline intrusives  

International Nuclear Information System (INIS)

New Rb-Sr age measurements are reported for a number of intrusives from Angola. Data for the Njoio and Tchivira nepheline syenite bodies yield mineral isochrons indicating ages of 104,3+-0,8 Ma and 130,8+-1,4 Ma respectively. Palaeomagnetic studies on the same occurrences gave marginal and scattered results respectively. Micas from the Camafuca crater-facies kimberlite yielded and apparent age of 1 822+-151 Ma, a result that is far in excess of the Tertiary (or younger) age inferred for this pipe. Similarly conflicting data were obtained for the Nova Lisboa kimberlite. It is likely that older crustal micas incorporated in the kimberlite breccias are responsible for the anomalous ages reported on the kimberlites. Satisfactory palaeomagnetic data are reported for the Zenza and Bailundu occurrences, not dated by the Rb-Sr method. A convenient K-Ar age of 80+-0,8 Ma was obtainable for Zenza.

149

Idaho National Laboratory Supervisory Control and Data Acquisition Intrusion Detection System (SCADA IDS)  

Energy Technology Data Exchange (ETDEWEB)

Current Intrusion Detection System (IDS) technology is not suited to be widely deployed inside a Supervisory, Control and Data Acquisition (SCADA) environment. Anomaly- and signature-based IDS technologies have developed methods to cover information technology-based networks activity and protocols effectively. However, these IDS technologies do not include the fine protocol granularity required to ensure network security inside an environment with weak protocols lacking authentication and encryption. By implementing a more specific and more intelligent packet inspection mechanism, tailored traffic flow analysis, and unique packet tampering detection, IDS technology developed specifically for SCADA environments can be deployed with confidence in detecting malicious activity.

2008-05-01

150

Geochemistry and petrogenesis of Neoproterozoic Mylliem granitoids, Meghalaya Plateau, northeastern India  

British Library Electronic Table of Contents (United Kingdom)

The Mylliem granitoids of the Meghalaya Plateau, northeastern India, represent one of the disharmonic Neoproterozoic igneous plutons, which are intrusive into low-grade Shillong Group of metasediments. Field studies indicate that the Mylliem granitoids cover an area of about 40 km2 and is characterized by development of variable attitude of primary foliations mostly marked along the margin of the pluton. Xenoliths of both Shillong Group of metasediments and mafic rocks have been found to occur within Mylliem granitoids. Structural study of the primary foliation is suggestive of funnel-shaped intrusion of Mylliem granitoids with no appreciable evidence of shearing. Petrographically, Mylliem granitoids are characterized by pink to white phenocrysts of prismatic microcline/perthite and lath-s...

2011-01-01

151

Enzymatic catalysis in cosolvent modified pressurized organic solvents.  

Science.gov (United States)

An important advantage of carrying out enzymatic catalysis in organic media is the increased solubility of hydrophobic substrates. This study compares a model lipase catalyzed esterification of cholesterol using vinyl acetate (VA) in two such nontraditional media: high-pressure hexane and supercritical (SCF) ethane. The effect of using one of the reactants (VA) as a cosolvent to increase the solubility of the other reactant (cholesterol) in SCF ethane has been investigated. The thermodynamic activity of water (a(w)) in the reaction media was controlled by the direct addition of the salt hydrate pair Na(4)P(2)O(7)/Na(4)P(2)O(7).10H(2)O. The a(w) of the salt hydrate system is shown to be a function of pressure and its variation over the pressure range 104-173 bar has been estimated. The initial reaction rate in pressurized hexane was found to vary linearly with the cholesterol concentration. The reaction rate was also a ...

1999-11-01

152

DIVALENT ION EXCHANGE WITH ALKALI  

Energy Technology Data Exchange (ETDEWEB)

Exchange of hardness ions is important in enhanced oil recovery with chemical additives. In both micellar-polymer and caustic flooding processes, multivalent ions released from rock surfaces can interact with anionic surfactants, rendering them preferentially oil soluble and/or insoluble in water. Because hardness cations are sparingly soluble and precipitate in alkaline solutions, such solutions may be more efficient as surfactant flood preflushes than are softened brines. Multivalent ion precipitation may also occur in alkaline waterflooding. To permit design of such processes, this paper presents a chromatographic theory for simultaneous ion exchange with precipitation of divalent ions. Theoretical effluent histories and concentration profiles are presented for the cases of finite pulses and continuous injection of hydroxide ions into linear cores. Complete capture of the insoluble salt particles is assumed. Results are given for the case of ...

1980-05-01

153

Characterization of pore structure in cement-based materials using pressurization-depressurization cycling mercury intrusion porosimetry (PDC-MIP)  

International Nuclear Information System (INIS)

Numerous mercury intrusion porosimetry (MIP) studies have been carried out to investigate the pore structure in cement-based materials. However, the standard MIP often results in an underestimation of large pores and an overestimation of small pores because of its intrinsic limitation. In this paper, an innovative MIP method is developed in order to provide a more accurate estimation of pore size distribution. The new MIP measurements are conducted following a unique mercury intrusion procedure, in which the applied pressure is increased from the minimum to the maximum by repeating pressurization-depressurization cycles instead of a continuous pressurization followed by a continuous depressurization. Accordingly, this method is called pressurization-depressurization cycling MIP (PDC-MIP). By following the PDC-MIP testing sequence, the volumes of the throat pores and the corresponding ink-bottle pores can be determined at every pore size. These ...

2010-07-01

154

Buried Paleo-Phreatic Playa is the Primary Source of Salinity in the Rio Grande and Rio Grande Aquifer, El Paso-Juarez Valley  

Science.gov (United States)

The Rio Grande alluvial floodplain aquifer between El Paso/Juarez and Fort Quitman, Texas has been intensively tilled and irrigated since 1910. Almost since that time, the Rio Grande and its interconnected alluvial aquifer in this stream reach have been affected by excessive salinity problems. Presently, salinity of surface water and groundwater increases from 800 to 2000 mg/L total dissolved solids (TDS) near El Paso, Texas to 2500 to 5500 mg/L TDS near Fort Quitman, Texas, approximately 115 km downstream. Chloride (Cl) and Chloride/Bromide (Cl/Br) ratios increase downstream, with a marked increase in salinity beginning about 45 km below El Paso. Groundwater sampling in an intensively investigated reach of the floodplain aquifer, extending from 35 to 60 km below El Paso identified two distinct water types. The first water type (17 samples) is a relatively dilute groundwater containing 1000 to 2000 mg/L TDS, 250 to 600 ...

2005-12-01

155

Use of clays as liners in solar ponds  

Energy Technology Data Exchange (ETDEWEB)

An alternative to synthetic materials for use in solar pond liners is to select clayey soils as hydraulic barriers. This option reduces the cost of construction and the risk of contamination of subsoil and groundwater by hot brines. This paper deals with the physical, chemical and hydraulic properties of different soils tested mainly as compacted clay liners. The underdeveloped nations have the option to use this type of liner, but before doing so several tests are recommended, including those for soil and water composition, permeability, plasticity and X-ray diffraction analysis. In this investigation the following samples are analyzed: native clayey soils with illite, montmorillonite and halloysite, treated and non-treated bentonites in powder and granulated form, a mixture of zeolite and sodium bentonite, and industrial minerals composed largely of halloysite, kaolinite and attapulgite selected clays. Neutral salt aqueous solutions (NaCl and ...

2009-06-15

156

The next wave : kaleidoscope project aims to break the sound barrier of seismic imaging  

Energy Technology Data Exchange (ETDEWEB)

This article discussed a project formed to develop innovative seismic imaging technologies. The Kaleidoscope project aims to accelerate the processing of seismic sound waves by several orders of magnitude using advanced computer-based techniques to reveal oil and gas deposits buried deep in the earth in a manner that is both cost-effective and efficient. It is expected that the technology will be used in deep water applications with massive untapped reserves. The seismic technology will be used to locate hydrocarbons and oil reserves buried 20,000 feet beneath the seabed. It is estimated that the Gulf of Mexico contains 56 billion barrels of oil equivalent worth nearly $6 trillion. However, the reserves are difficult to locate due to the interbedded salt bodies in the subsurface. The project is simultaneously working on both hardware and software applications, and are currently writing the first petascale set of seismic imaging applications. ...

2008-05-15

157

Laboratory Evaluation of an Electrochemical Noise System for Detection of Localized and General Corrosion of Natural Gas Transmission Pipelines  

Energy Technology Data Exchange (ETDEWEB)

Gas transmission pipelines are susceptible to both internal (gas side) and external (soil side) corrosion attack. Internal corrosion is caused by the presence of salt laden moisture, CO{sub 2}, H{sub 2}S, and perhaps O{sub 2} in the natural gas. Internal corrosion usually manifests itself as general corrosion. However, the presence of chlorides in entrained water also can lead to pitting corrosion damage. The electrochemical noise technique can differentiate general from localized corrosion and provide estimates of corrosion rates without external perturbation of the corroding system. It is increasingly being applied to field and industrial installations for in situ corrosion monitoring. It has been used here to determine its suitability for monitoring internal and external corrosion damage on gas transmission pipelines. Corrosion measurements were made in three types of environments: (1) aqueous solutions typical of those found within gas ...

2003-03-16

158

Ecology of microorganisms in desert soil environment. Sabaku dojo kankyo ni okeru biseibutsu seitai  

Energy Technology Data Exchange (ETDEWEB)

This paper indicates first that the base content in desert soil is by far much higher than that in soils in moist areas, that salts with the higher solubility to water have their deposition depth greater, and that the organic content is extremely low. The paper also describes the experiments to verify that the desert soil contains soil lumps with a diameter of about several millimeters, which function effectively to form the long term survival locations for microorganisms. Desert soil containing soil lumps and the one removed of lumps by pulverizing them into powder were prepared as test specimens, which were left submerged. It was confirmed that the velocity of decomposing the organics and the mechanical strength in the latter soil are obviously inferior to those in the former soil. Additional remarks are given that when the desert soil environment is changed the microorganisms get more active appreciably and that certain kinds of mold fungi ...

1991-11-01

159

Dodecanuclear rhenium cluster complexes with an interstitial carbon atom: Synthesis, structures and properties of two new compounds K6[Re12CS17(OH)6]?4H2O and Na12Re12CS17(SO3)6?48.5H2O  

British Library Electronic Table of Contents (United Kingdom)

The dodecanuclear rhenium anionic complex with terminal hydroxo ligands [Re12CS17(OH)6]6? was obtained by the reaction of K6[Re12CS17(CN)6]?20H2O with molten KOH at 300 ?C. The cluster complex was crystallized as a potassium salt from aqueous solution. The reaction between K6[Re12CS17(OH)6]?4H2O and Na2S2O4 in water under reflux results in the formation of the complex Na12[Re12CS17(SO3)6]?48.5H2O. Both new compounds were characterized by single-crystal X-ray diffraction, elemental analyses and IR spectroscopy. The electronic structure of [Re12CS17(OH)6]6? was also elucidated by DFT calculation

2010-01-01

160

Chalk Point cooling tower project native vegetation study. Final report 1979  

Science.gov (United States)

The Potomac Electric Power Company generating station at Chalk Point, MD, utilizes brackish water in its natural draft cooling tower and, consequently, releases saline aerosol into the atmosphere. A research and monitoring project was established in 1974 to evaluate the effects of this drift on native perennial vegetation. Leaf samples have been collected form dogwood, Cornys florida, Virginia pine, Pinus virginiana, black locust, Robinia pseudoacacia, and sassafras, Sassafras albidum, located at 12 different sites in the vicinity of the power plant. Sampling was begun prior to the operation of the cooling tower, 1974, and continued through 1978. Complete results from monthly monitoring of foliar chloride in the four native tree species is documented for May through September 1978. Results from salt spray experiments indicate chloride and sodium concentrations in the wood of dogwood trees increases with increased spraying levels.

1979-06-01

161

Behavior at under-film corrosion tips of Zn-Fe alloy coated steel sheets. Zn-Fe gokin mekki koban no tomakushita fushoku ni okeru fushoku sentanbu no kyodo  

Energy Technology Data Exchange (ETDEWEB)

From a macroscopic point of view, corrosion of Zn alloy coated steel sheet occurs by the coating preceding corrosion mechanism; microscopically, however, the coated layer corrosion velocity in the tip of corrosion is different. In order to find the main factors of under-film corrosion of Zn and Zn-Fe alloy coatings in the salt water spray atmospheric exposure test, the correlation between point inflation-exfoliation width and chlorine penetration behavior, point adhesion, and the difference in chlorine penetration behavior due to alloy coating components were investigated. Consequently, the following results were obtained: 1. The better correlation was observed between chlorine penetration distance and point inflation-point exfoliation width. 2. The durability of coating against chlorine penetration improved by increase in point adhesion and Zn content in the coating layer. 3. Zn-Fe (10-20%) alloy coating showed better durability against ...

1990-09-01

162

Adsorption based processes as alternative to common gas conditioning at underground storage facilities using Sorbead; Procedes bases sur l'adsorption comme solution de rechange dans le conditionnement du gaz dans des lieux de stockage souterrains a l'aide de Sorbead  

Energy Technology Data Exchange (ETDEWEB)

The European gas market is continuing to expand due to increased industrial, domestic and power generation demand. As a result of this demand, and the trend toward liberalization of the market, the need for storage of gas is also increasing. One key segment of the large scale storage of gas is underground storage, either in partially depleted gas or oil fields, naturally occurring caverns, aquifers and salt cavities. In most cases the gas produced after storage requires conditioning to meet the water of hydrocarbon dew point specification of the gas transmission system. For that reason export gas from storage will require gas conditioning in order to meet pipeline specifications. Adsorption as a feasible and reliable process will be presented in detail and especially in regards to hydrocarbon dew-pointing compared with other process options. (author)

2000-07-01

163

System Requirements Document for the Molten Salt Reactor Experiment  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the conversion process is to convert the {sup 233}U fluoride compounds that are being extracted from the Molten Salt Reactor Experiment (MSRE) equipment to a stable oxide for long-term storage at Bldg. 3019.

2000-04-01

164

Role of Conserved Salt Bridges in Homeodomain Stability and DNA Binding*  

UK PubMed Central (United Kingdom)

The sequence information available for homeodomains reveals that salt bridges connecting pairs 19/30, 31/42, and 17/52 are frequent, whereas aliphatic residues at these sites are rare and mainly restricted...Full Text Available

2009-08-28

165

Non-contiguous regions of Z-DNA in a DNA dodecamer.  

UK PubMed Central (United Kingdom)

The conformation of the self-complimentary DNA dodecamer d(br5CGbr5CGAATTbr5CGbr5CG) has been investigated in a variety of salt and solvent conditions by one and two-dimensional 1H NMR. In low salt...Full Text Available

1989-10-11

166

Electrolytic Reduction: Modification of Proteins Occurring in Isoelectric Focusing Electrophoresis and in Electrolytic Reactions in the Presence of High Salts  

UK PubMed Central (United Kingdom)

Artifacts in two-dimensional electrophoresis (2-DE) caused by the presence of salts in isoelectric focusing (IEF) have been previously described as a result of increasing conductivity and inducing electroosmosis....Full Text Available

2009-05-15

167

Effect of association processes on polymerization of N-[3-(dimethylamino)propyl]methacrylamide salts in aqueous solutions  

British Library Electronic Table of Contents (United Kingdom)

The effect of associative interactions of monomers and propagating macroradicals in homopolymerization of N-[3-(dimethylamino)propyl]methacrylamide salts and their copolymerization with acrylonitrile and acrylamide in aqueous solution was studied.

2010-01-01

168

Crushed Salt Constitutive Model  

Energy Technology Data Exchange (ETDEWEB)

The constitutive model used to describe the deformation of crushed salt is presented in this report. Two mechanisms -- dislocation creep and grain boundary diffusional pressure solution -- are combined to form the basis for the constitutive model governing the deformation of crushed salt. The constitutive model is generalized to represent three-dimensional states of stress. Upon complete consolidation, the crushed-salt model reproduces the Multimechanism Deformation (M-D) model typically used for the Waste Isolation Pilot Plant (WIPP) host geological formation salt. New shear consolidation tests are combined with an existing database that includes hydrostatic consolidation and shear consolidation tests conducted on WIPP and southeastern New Mexico salt. Nonlinear least-squares model fitting to the database produced two sets of material parameter values for the model -- one for the ...

1999-02-01

169

Conformational stability of alternating d (CG) oligomers in high salt solution.  

UK PubMed Central (United Kingdom)

The conformation of d (CG)n oligomers with n = 2,3 has been studied in aqueous solution in the presence of high salt concentration. A minimum n value of three is necessary to obtain a left-handed Z-helix....Full Text Available

1981-05-11

170

Chromosome substitution reveals the genetic basis of Dahl salt-sensitive hypertension and renal disease  

UK PubMed Central (United Kingdom)

This study examined the genetic basis of hypertension and renal disease in Dahl SS/Mcwi (Dahl Salt-Sensitive) rats using a complete chromosome substitution panel of consomic rats in which each of the...Full Text Available

2008-09-01

171

Sc"4"5 NMR of scandium(3) salt aqueous solutions  

International Nuclear Information System (INIS)

Russian (Jul 1974). USSR Buslaev, Yu.A. Petrosyants, SP Tarasov,

172

Analysis of salt creep for a nuclear waste repository  

International Nuclear Information System (INIS)

(1981). United States Kadar, I. Li, WT Todeschini, R. Wu, CL Bechtel, Downey,

173

Enrichment of trace cadmium by soybean protein for the analysis by atomic absorption method  

International Nuclear Information System (INIS)

A method for enrichment of the ppb level of cadmium in water by using the coagulation of soybean protein by adding acids or its complex-forming character with heavy metal ions was investigated. After adding fixed amounts of soybean milk and 2% sodium diethyldithiocarbamate(DDTC) aqueous solution and a suitable amount of delta-gluconic lactone (delta-GL) to a sample solution, the mixture was heated to boiling in order to coagulate the protein. The coagulum(soybean curd) was separated from the suspension by centrifugation and burned to ashes with a low temperature plasma asher. Then the cadmium enriched in it was determined by atomic absorption spectrometry. Various factors such as the pH of the sample solution, the amounts of soybean milk and the collection additives, and the concentration of NaCl in the sample solution on the recovery of cadmium were examined systematically. The best recovery was obtained under the following conditions: To a certain amount of ...

1975-01-01

174

Principles of the coprecipitation of thorium and yttrium with organicinorganic salts of molybdenum polyacids  

Energy Technology Data Exchange (ETDEWEB)

This paper advances hypotheses on the chemistry of the interaction of thorium and yttrium with organic-inorganic salts of molybdenum polyacids. On the basis of an analysis of the data of an adsorption experiment and the quantitative relationships that follow from the law of mass action, it is shown that thorium is absorbed by the solid phase by coprecipitation with the participation of complex formation, while the coprecipitation of yttrium with salts of polyacids is due to a reaction of ion exchange chemisorption.

1986-03-01

175

Catalytic hydrothermal gasification of biomass for the production of synthetic natural gas[Dissertation 17100  

Energy Technology Data Exchange (ETDEWEB)

Energy from biomass is a CO{sub 2} neutral, sustainable form of energy. Anaerobic digestion is an established technology for converting biomass to biogas, which contains around 60% methane, besides CO{sub 2} and various contaminants. Most types of biomass contain material that cannot be digested; in woody biomass, this portion is particularly high. Therefore, conventional anaerobic digestion is not suited for the production of biogas from woody biomass. While wood is already being converted to energy by conventional thermal methods (gasification with subsequent methanation), dung, manure, and sewage sludge represent types of biomass whose energy potential remains largely untapped (present energetic use of manure in Switzerland: 0.4%). Conventional gas phase processes suffer from a low efficiency due to the high water content of the feed (enthalpy of vaporization). An alternative technology is the hydrothermal gasification: the water contained ...

2007-07-01

176

Proceedings of the workshop on molten salts technology and computer simulation  

Energy Technology Data Exchange (ETDEWEB)

Applications of molten salts technology to separation and synthesis of materials have been studied eagerly, which would develop new fields of materials science. Research Group for Actinides Science, Department of Materials Science, Japan Atomic Energy Research Institute (JAERI), together with Reprocessing and Recycle Technology Division, Atomic Energy Society of Japan, organized the Workshop on Molten Salts Technology and Computer Simulation at Tokai Research Establishment, JAERI on July 18, 2001. In the workshop eleven lectures were made and lively discussions were there on the fundamentals and applications of the molten salts technology that covered the structure and basic properties of molten salts, the pyrochemical reprocessing technology and the relevant computer simulation. The 10 of the presented papers are indexed individually. (J.P.N.)

2001-12-01

177

Physiological and antioxidant responses of Mentha pulegium (Pennyroyal) to salt stress  

British Library Electronic Table of Contents (United Kingdom)

Mentha pulegium L. is a medicinal and aromatic plant belonging to the Labiatae family present in the humid to the arid bioclimatic regions of Tunisia. We studied the effect of different salt concentrations on plant growth, mineral composition and antioxidant responses. Physiological and biochemical parameters were assessed in the plant organs after 2?weeks of salt treatment with 25, 50, 75 and 100?mM NaCl. Results showed that, growth was reduced even by 25?mM, and salt effect was more pronounced in shoots (leaves and stems) than in roots. This growth decrease was accompanied by a restriction in tissue hydration and K+ uptake, as well as an increase in Na+ levels in all organs. Considering the response of antioxidant enzymes to salt, leaves and roots reacted differently to saline conditions...

2010-01-01

178

Detection of Fluorescence for Lanthanides in LiCl-KCl Molten Salt Medium  

Energy Technology Data Exchange (ETDEWEB)

In the electrorefining step of the pyrochemical process, actinide ions dissolved in the LiCl-KCl eutectic salt are recovered as pure actinide metals at a cathode for a re-use as a nuclear fuel from the aspect of its nonproliferation of the nuclear fuel cycles. The lanthanide species dissolved in the LiCl-KCl eutectic salt play an important role in an effective metal purification during the electrorefining step, so it is necessary to understand the chemical and physical behaviors of lanthanides in molten salt. The in situ spectroscopic measurement system and studies according to temperature changes are essential for better understandable information. To our knowledge, the absorption studies of lanthanides at high temperatures have been reported before, but the fluorescence studies of those at high temperature are not reported yet. We will discuss here the fluorescence behaviors of lanthanides in LiCl-KCl molten ...

2007-10-15

179

Detection of Fluorescence for Lanthanides in LiCl-KCl Molten Salt Medium  

International Nuclear Information System (INIS)

In the electrorefining step of the pyrochemical process, actinide ions dissolved in the LiCl-KCl eutectic salt are recovered as pure actinide metals at a cathode for a re-use as a nuclear fuel from the aspect of its nonproliferation of the nuclear fuel cycles. The lanthanide species dissolved in the LiCl-KCl eutectic salt play an important role in an effective metal purification during the electrorefining step, so it is necessary to understand the chemical and physical behaviors of lanthanides in molten salt. The in situ spectroscopic measurement system and studies according to temperature changes are essential for better understandable information. To our knowledge, the absorption studies of lanthanides at high temperatures have been reported before, but the fluorescence studies of those at high temperature are not reported yet. We will discuss here the fluorescence behaviors of lanthanides in LiCl-KCl molten ...

2007-10-01

180

Surface activity at the planar interface in relation to the thermodynamics of intermolecular interactions in the ternary system: maltodextrin-small-molecule surfactant-legumin.  

Science.gov (United States)

We report on the effect of potato maltodextrins with variable dextrose equivalent (Paselli SA-2, SA-6 and SA-10) on the surface behavior at the air-water interface of the mixture: legumin+small-molecule surfactant. Distinct in nature small-molecule surfactants (model: sodium salt of capric acid, Na-caprate; and commercially important: a citric acid ester of monoglyceride, CITREM) have been under our consideration. The role of the structure of both of the maltodextrins and the small-molecule surfactants in the effect studied has been elucidated by measurements in a bulk aqueous medium of the enthalpy of their interaction from mixing calorimetry, value of weight average molecular weight of the maltodextrins and the thermodynamics of the pair maltodextrin-solvent and maltodextrin-protein interactions from laser static light scattering. The combined data of mixing calorimetry and light scattering suggest some complex formation between the ...

2001-07-01

181

Structural definition of the active site and catalytic mechanism of 3,4-dihydroxy-2-butanone 4-phosphate synthase  

Energy Technology Data Exchange (ETDEWEB)

X-ray crystal structures of L-3,4-dihydroxy-2-butanone-4-phosphate synthase from Magnaporthe grisea are reported for the E-SO{sub 4}{sup 2-}, E-{sub 4}{sup 2-}-Mg{sup 2+}, E-SO{sub 4}{sup 2-}-Mn{sup 2+}, E-SO{sub 4}{sup 2-}-Mn{sup 2+}-glycerol, and E-SO{sub 4}{sup 2-}-Zn{sup 2+} complexes with resolutions that extend to 1.55, 0.98, 1.60, 1.16, and 1.00 {angstrom}, respectively. Active-site residues of the homodimer are fully defined. The structures were used to model the substrate ribulose 5-phosphate in the active site with the phosphate group anchored at the sulfate site and the placement of the ribulose group guided by the glycerol site. The model includes two Mg{sup 2+} cations that bind to the oxygen substituents of the C2, C3, C4, and phosphate groups of the substrate, the side chains of Glu37 and His153, and water molecules. The position of the metal cofactors and the substrate's phosphate group are further stabilized by an extensive hydrogen-bond ...

2010-03-08

182

Modeling microbial spoilage and quality of gilthead seabream fillets: combined effect of osmotic pretreatment, modified atmosphere packaging, and nisin on shelf life.  

Science.gov (United States)

The objective of the study was the kinetic modeling of the effect of storage temperature on the quality and shelf life of chilled fish, modified atmosphere-packed (MAP), and osmotically pretreated with the addition of nisin as antimicrobial agent. Fresh gilthead seabream (Sparus aurata) fillets were osmotically treated with 50% high dextrose equivalent maltodextrin (DE 47) plus 5% NaCl. Water loss, solid gain, salt content, and water activity were monitored throughout treatment and treatment conditions were selected for the shelf life study. Untreated and osmotically pretreated slices with and without nisin (2 x 10(4) IU/100 g osmotic solution), packed in air or modified atmosphere (50% CO(2)-50% air), and stored at controlled isothermal conditions (0, 5, 10, and 15 degrees C) were studied. Quality assessment and modeling were based on growth of several microbial indices, total volatile nitrogen, trimethylamine nitrogen, ...

2010-05-01

183

Further development of the RTFE technique for the comprehensive management of liquid radioactive wastes from Russian NPP in Comecon countries. Final report; Weiterentwicklung der RDA-Technologie fuer die umfassende Entsorgung von in den RGW-Laendern anfallenden radioaktiven Fluessigkeiten aus KKW sowjetischen Typs. Schlussbericht  

Energy Technology Data Exchange (ETDEWEB)

The composition of alkaline and neutral boric acid containing evaporator concentrates resulting from the treatment of radioactive waste water in nuclear power plants with WWER reactors is described as well as the processing of these concentrates to a product suitable for final disposal. Tests with mock solutions of these evaporator concentrates have been performed at the laboratory and teststand scale to produce a dry residue by continuous thickening, which can be processed into a highly leach resistant product, suitable for final disposal, by cementation. Ca-compounds must be added to the evaporator concentrates prior to the drying in an rotary thin-film evaporator (RTFE). The tests showed that neutral evaporator concentrates can be dried in a RTFE with addition of small amounts of Ca-compounds. The alkaline evaporator concentrates with high boric acid and total salt load require a multiple amount of Ca-compounds and diluting ...

1992-04-01

184

Formation of silk fibroin nanoparticles in water-miscible organic solvent and their characterization  

Energy Technology Data Exchange (ETDEWEB)

When Silk fibre derived from Bombyx mori, a native biopolymer, was dissolved in highly concentrated neutral salts such as CaCl{sub 2}, the regenerated liquid silk, a gradually degraded peptide mixture of silk fibroin, could be obtained. The silk fibroin nanoparticles were prepared rapidly from the liquid silk by using water-miscible protonic and polar aprotonic organic solvents. The nanoparticles are insoluble but well dispersed and stable in aqueous solution and are globular particles with a range of 35-125 nm in diameter by means of TEM, SEM, AFM and laser sizer. Over one half of the {epsilon}-amino groups exist around the protein nanoparticles by using a trinitrobenzenesulfonic acid (TNBS) method. Raman spectra shows the tyrosine residues on the surface of the globules are more exposed than those on native silk fibers. The crystalline polymorph and conformation transition of the silk nanoparticles from random-coil and {alpha}-helix form ...

2007-10-15

185

Site characterization and petroleum hydrocarbon plume mapping  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a case study of site characterization and hydrocarbon contamination plume mapping/delineation in a gas processing plant in southern Mexico. The paper describes innovative and cost-effective use of passive (non-intrusive) and active (intrusive) techniques, including the use of compound-specific analytical methods for site characterization. The techniques used, on a demonstrative basis, include geophysical, geochemical, and borehole drilling. Geochemical techniques used to delineate the horizontal extent of hydrocarbon contamination at the site include soil gas surveys. The borehole drilling technique used to assess the vertical extent of contamination and confirm geophysical and geochemical data combines conventional hollow-stem auguring with direct push-probe using Geoprobe. Compound-specific analytical methods, such as hydrocarbon fingerprinting and a modified method for gasoline range organics, demonstrate the inherent ...

1996-12-31

186

Network security: a survey of modern approaches  

International Nuclear Information System (INIS)

Security is an essential element of information technology (IT) infrastructure and applications. Concerns about security of networks and information systems have been growing along with the rapid increase in the number of network users and the value of their transactions. The hasty security threats have driven the development of security products known as Intrusion Detection Systems (IDS) and Intrusion Prevention Systems (IPS) to detect and protect the network, server and desktop infrastructure ahead of the threat. Authentication and signing techniques are used to prevent integrity threats. Users, devices, and applications should always be authenticated and authorized before they are allowed to access networking resources. Though a lot of information is available on the internet about IDS and IPS but it all is spread on so many sites and one has to spend a considerable part of his precious time to search it. In this regard a thorough survey has ...

2008-01-01

187

Network security: a survey of modern approaches  

International Nuclear Information System (INIS)

Security is an essential element of information technology (IT) infrastructure and applications. Concerns about security of networks and information systems have been growing along with the rapid increase in the number of network users and the value of their transactions. The hasty security threats have driven the development of security products known as Intrusion Detection Systems (IDS) and Intrusion Prevention Systems (IPS) to detect and protect the network, server and desktop infrastructure ahead of the threat. Authentication and signing techniques are used to prevent integrity threats. Users, devices, and applications should always be authenticated and authorized before they are allowed to access networking resources. Though a lot of information is available on the internet about IDS and IPS but it all is spread on so many sites and one has to spend a considerable part of his precious time to search it. In this regard a thorough survey has ...

188

Rb-Sr age of the Sundsta granite in the Western Pregothian tectonic mega-unit, south-western Sweden  

Energy Technology Data Exchange (ETDEWEB)

The Sundsta granite is a reddish, acidic granite, situated in the Western Pregothian mega-unit in Vaermland, south-western Sweden. Its Rb-Sr whole-rock age is 1566+-39 Ma with an initial ratio 0f 0.705 +-0.003. The region is dominated by grey, migmatized granitoids presumably belonging to the Aamaal-I group which has ages of 1650-1700 Ma. The marked difference in degree of migmatization between these two rock-units may indicate that the intrusion of the Sundsta granite post-dates the main migmatization phase of the Aamaal-I granitoid in this region.

1982-10-25

189

Correction of skeletal Class II-anterior deep bite and prominent chin by forced surgical rotation of the mandible  

British Library Electronic Table of Contents (United Kingdom)

The purpose of this paper is to describe a technique of forced surgical rotation of the mandible used in skeletal Class II patients with deep bite and prominent chin. Posterior occlusal composite onlays combined with preoperative orthodontic treatment without anterior intrusion increase the posterior rotational component of the surgical mandibular advancement, when removed during operation. This manoeuvre allows for the surgical closure of the posterior open bite, while anteriorly the deep bite is opened. This technique avoids bimaxillary rotation surgery with dorsal impaction in mild to moderate cases. In any case, a chin setback osteotomy with compromised aesthetics can be avoided.

2010-01-01

190

Broadband Local Area Network security monitoring--Magnovox CATV Systems Inc. Digital System Sentry product evaluation  

Energy Technology Data Exchange (ETDEWEB)

Use of a broadband Local Area Network (LAN) for transmission of classified and secure unclassified information requires monitoring capabilities which are sensitive to discrete segments of the network frequency spectrum. A viable monitoring system must be capable of detecting possible intrusion attempts or network malfunctions and alerting operating and security personnel. This report documents the results of an evaluation of the Magnavox CATV Systems Inc. Digital System Sentry software for network monitoring. Recommendations are made on its possible future role in broadband LAN security monitoring throughout the Nuclear Weapons Complex.

1991-01-01

191

Treatment of a waste salt delivered from an electrorefining process by an oxidative precipitation of the rare earth elements  

Energy Technology Data Exchange (ETDEWEB)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO{sub 2}, PrO{sub 2}), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion efficiencies of the rare earth elements ...

2009-02-28

192

Treatment of a waste salt delivered from an electrorefining process by an oxidative precipitation of the rare earth elements  

International Nuclear Information System (INIS)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion efficiencies of the rare earth elements to their ...

2009-02-28

193

Method for preparing drilling solutions that are resistant in Zechstein deposits  

Energy Technology Data Exchange (ETDEWEB)

The patent is for a method of preparing drilling muds that are notable for their chemical resistance to Zechstein deposits, especially to magnesium, carbonate and carboxylic acid ions. To achieve chemical resistance of the drilling mud to Zechstein deposits, it is suggested to saturate them with salt (the amount of added salt depends on the absorption properties of the solution), and then to process them with caustic soda or potassium oxide hydrate and lime in proportions that would cause filtrate alkalinity not to exceed 0.5. For example, to prepare drilling solution to bore through mediums containing magnesium salts, potassium salts, rock salt, anhydrate, dolomite, limestone, red salt clay: add 340 kg potassium chloride into 1 m/sup 3/ drilling solution with weighed bentonic clay, 10 kg. ferro-chromate lignosulfite, 7 kg. unslaked lime, 2 kg. sodium hydroxide, ...

1980-05-31

194

Evaluation of static thermophysical properties of the ternary molten salt system Li, Na and Be/F based on the modified Peng-Robinson equation  

International Nuclear Information System (INIS)

The static thermophysical properties of the molten salt system like LiF-NaF-BeF_2 influence the design and construction of the fuel salt and coolant in the Molten Salt Reactor for the new generation. In this paper, the equation of state of the ternary system 0.15LiF-0.58NaF-0.27BeF_2, over the temperature range from 873.15K to 1073.15K at one atmosphere pressure, is described by using modified Peng-Robinson equation. The density of the ternary system is evaluated by this equation directly, and compared with the experimental data. Base on the equation of state, the other static thermophysical properties such as the enthalpy, entropy and heat capacity at constant pressure are evaluated by the fugacity coefficient and residual function methods respectively. The density calculated by Peng-Robinson equation is in highly agreement with the experimental data, and the enthalpy, entropy and heat capacity evaluated by such two ...

2008-03-01

195

Evaluation of static thermodynamic properties of the ternary molten salt system Li,Na,Be/F, based on the modified Peng-Robinson equation  

International Nuclear Information System (INIS)

The static thermodynamic properties of the molten salt system like LiF-NaF-BeF_2 influence the design and construction of the fuel salt and coolant in the Molten Salt Reactor for the new generation. In this paper, the equation of state of the ternary system 15%LiF-58%NaF-27%BeF_2, over the temperature range of 873.15K to 1073.15K at one atmosphere pressure, is described using Peng-Robinson equation modified by us. And the density of the ternary system is evaluated by this equation directly, and compared with the experimental data. Base on the equation of state, the other static thermodynamic properties such as the enthalpy, entropy and heat capacity at constant pressure are estimated by the residual function method and the fugacity coefficient method respectively. The density calculated by Peng-Robinson equation is in highly agreement with the experimental data, and the enthalpy, entropy and heat capacity evaluated by such ...

2007-04-22

196

Evaluation of Static Thermophysical Properties of the Ternary Molten Salt System Li, Na and Be/F Based on the Modified Peng-Robinson Equation  

Science.gov (United States)

The static thermophysical properties of the molten salt system like LiF-NaF-BeF2 influence the design and construction of the fuel salt and coolant in the Molten Salt Reactor for the new generation. In this paper, the equation of state of the ternary system 0.15LiF-0.58NaF-0.27BeF2, over the temperature range from 873.15K to 1073.15K at one atmosphere pressure, is described by using modified Peng-Robinson equation. The density of the ternary system is evaluated by this equation directly, and compared with the experimental data. Base on the equation of state, the other static thermophysical properties such as the enthalpy, entropy and heat capacity at constant pressure are evaluated by the fugacity coefficient and residual function methods respectively. The density calculated by Peng-Robinson equation is in highly agreement with the experimental data, and the enthalpy, entropy and heat capacity evaluated by such two ...

2008-01-01

197

Crack tip oxidation of a superalloy in molten nitrate salt  

Energy Technology Data Exchange (ETDEWEB)

Alloy 800 has been proposed for use in the receiver tube panel arrays of advanced solar central receiver (SCR) designs. In this application the alloy will be exposed to a molten mixture of sodium and potassium nitrate salts at temperatures ranging up to approximately 600/sup 0/C While these salts are routinely used in a variety of applications including metal heat treating and process heat transfer, common industrial experience has been limited to maximum temperatures of 400/sup 0/C - 450/sup 0/C. There is, therefore, considerable interest in the compatibility of these salts with containment alloys at the higher temperatures associated with SCR designs. Additionally, the containment alloy may be subject to thermally induced fatigue damage resulting from intermittent cloud cover and diurnal cycling. Previous work has found that slower near-threshold fatigue crack growth rates (FCGR) in Alloy 800 result when it is tested in ...

1983-04-01

198

Water Quality and 401 Certification | Clean Water Act | US EPA  

Science.gov (United States)

Clean Water Act You are here: Water Laws & Regulations Policy & Guidance Clean Water Act Water Quality and 401 Certification Water Quality and 401 Certification Water Quality...

2011-08-28

199

WASTE SOLIDIFICATION BUILDING BENCH SCALE HIGH ACTIVITY WASTE SIMULANT VARIABILITY STUDY FY2008  

Energy Technology Data Exchange (ETDEWEB)

The primary objective of this task was to perform a variability study of the high activity waste (HAW) acidic feed to determine the impact of feed variability on the quality of the final grout and on the mixability of the salt solution into the dry powders. The HAW acidic feeds were processed through the neutralization/pH process, targeting a final pH of 12. These fluids were then blended with the dry materials to make the final waste forms. A secondary objective was to determine if elemental substitution for cost prohibitive or toxic elements in the simulant affects the mixing response, thus providing a more economical simulant for use in full scale tests. Though not an objective, the HAW simulant used in the full scale tests was also tested and compared to the results from this task. A statistically designed test matrix was developed based on the maximum molarity inputs used to make the acidic solutions. The maximum molarity inputs were: 7.39 HNO{sub 3}, 0.11618 ...

2009-03-20

200

Technical report for fabrication and performance test of electrochemical/spectroscopic measurement system  

International Nuclear Information System (INIS)

Development of evaluation technology of electrochemical reactions is very essential to understand chemical behavior of actinides and lanthanides in molten salt media in relation to the development of Pyrochemical process. The on-line electrochemical/spectroscopic measurement system is to produce electrochemical parameters and thermodynamic parameters of actinides and lanthanides in molten salts by using spectroscopic techniques such as UV-VIS absorption as well as electrochemical in-situ measurement techniques. The on-line electrochemical/spectroscopic measurement system can be applied to understand the chemical reactions and oxidation states of actinides and lanthanides in molten salts eventually for the Pyrochemical process

2006-09-01

201

Performance of the gas bubble column in molten salt systems  

Energy Technology Data Exchange (ETDEWEB)

Experimental data on the gas holdup and the mean bubble size in a bubble column with a single nozzle was obtained for gas-molten salt systems of a eutectic mixture of LiCl (58 mol %)-KCl (42 mol %) and molten NaNO/sub 3/. The liquid-phase mass transfer coefficient K /SUB L/ was evaluated from the specific surface area a and the volumetric coefficient K /SUB L/ a data for oxygen and carbon dioxide absorption into molten NaNO/sub 3/. The dimensionless correlations of the performance of bubble columns for aqueous solutions can be extended to the gas-molten salt systems.

1984-01-01

202

Materials compatibility during the chlorination of molten CaCl/sub 2/. CaO salts. [CaCl/sub 2/. CaO salt  

Energy Technology Data Exchange (ETDEWEB)

As part of our effort to develop a semicontinuous PuO/sub 2/ reduction process, we are investigating promising materials for containing a 900/sup 0/C molten CaCl/sub 2/ . CaO chlorination reaction. We want the material to contain this reaction and to be reusable. We tested candidate materials in a simulated salt (no plutonium) using anhydrous HCl as the chlorinating agent. Data are presented on the performance of 36 metals and alloys, 9 ceramics, and 3 coatings.

1987-01-01

203

Extraction of lithium from neutral salt solutions with fluorinated #beta#-diketones  

International Nuclear Information System (INIS)

Lithium was selectively extracted from near-neutral aqueous solutions of alkali metal salts. The mechanism by which this was achieved involves the formation of the trioctylphosphine oxide adduct of a lithium chelate of a fluorinated #beta#-diketone, which is then readily extractable into an organic diluent. High separation factors were obtained from sodium, potassium, rubidium, and cesium. The selectivity of the fluorinated #beta#-diketones for lithium over the alkaline earths was found to be poor. A suggested general flowsheet for the recovery of lithium from a salt brine concentrate is included. (author).

204

Computational Analysis of the SRS Phase III Salt Disposition Alternatives  

Energy Technology Data Exchange (ETDEWEB)

Completion of the Phase III evaluation and comparison of salt disposition alternatives was supported with enhanced computer models and analysis for each case on the ''short list'' of four options. SPEEDUP(TM) models and special purpose models describing mass and energy balances and flow rates were developed and used to predict performance and production characteristics for each of the options. Results from the computational analysis were a key part of the input used to select a primary and an alternate salt disposition alternative.

1999-10-07

205

Treatment of a waste salt delivered from an electrorefining process by an oxidative precipitation of the rare earth elements  

British Library Electronic Table of Contents (United Kingdom)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two sha...

2009-01-01

206

Treatment of LiCl-KCl eutectic waste salt delivered from pyroprocessing of spent oxide fuel  

Energy Technology Data Exchange (ETDEWEB)

An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements.

2008-08-15

207

Treatment of LiCl-KCl eutectic waste salt delivered from pyroprocessing of spent oxide fuel  

International Nuclear Information System (INIS)

An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements

2008-08-01

208

Thermal modeling of solar central receiver cavities  

Energy Technology Data Exchange (ETDEWEB)

Results are presented from a numerical model of the steady-state energy transfer in molten-salt-in-tube solar cavity receivers that includes convective energy transfer at a local (spatially resolved) level. Molten salt energy absorption and gray radiative transfer between all cavity surfaces are also included. This model is applied to the Molten Salt Subsystem Component Test Experiment (MSS/CTE) cavity receiver. Results for this receiver indicate the global (entire cavity) receiver thermal efficiency is invariant within a few percent to most parameters investigated, although front surface temperatures of the nonabsorbing walls vary considerably, and are particularly sensitive to the type of convective submodel used. Absorption efficiencies indicate the effects of the cavity enclosure environment. For all conditions investigated, tube inner wall temperatures remain under 855 K, ensuring that the salt ...

1989-05-01

209

Thermal model and thermodynamic performance of molten salt cavity receiver  

British Library Electronic Table of Contents (United Kingdom)

The design of a global steady-state thermal model of a 100kWt molten salt cavity receiver was developed as part of the key project of the Ministry of Science and Technology of People's Republic of China (MOST). In the design process, the following factors were analyzed: receiver area, heat loss (convective, emissive, reflective and conductive), number of tubes in the receiver panel, tube diameter and receiver surface temperature. The model was also used to calculate the receiver performance of the Sandia National Laboratories' molten salt electric experiment (MSEE). In addition, the thermal performance of the designed molten salt cavity receiver is presented for a fixed outlet flow rate and a fixed output temperature.

2010-01-01

210

Salt modulates the stability and lipid binding affinity of the adipocyte lipid-binding proteins  

Science.gov (United States)

Adipocyte lipid-binding protein (ALBP or aP2) is an intracellular fatty acid-binding protein that is

2003-01-01

211

Salt Lake City shows hot and cold spots - NASA ... - Science@NASA  

Science.gov (United States)

Jul 21, 1998 ... Additional roof surface temperatures were taken with a handheld "heat spy," an infrared thermometer to help calibrate the ATLAS thermal ...

212

Research on Actinides in Nuclear Fuel Cycles  

International Nuclear Information System (INIS)

The electrochemical/spectroscopic integrated measurement system was designed and set up for spectro-electrochemical measurements of lanthanide and actinide ions in high temperature molten salt media. A compact electrochemical cell and electrode system was also developed for the minimization of reactants, and consequently minimization of radioactive waste generation. By applying these equipment, oxidation and reduction behavior of lanthanide and actinide ions in molten salt media have been made. Also, thermodynamic parameter values are determined by interpreting the results obtained from electrochemical measurements. Several lanthanide ions exhibited fluorescence properties in molten salt. Also, UV-VIS measurement provided the detailed information regarding the oxidation states of lanthanide and actinide ions in high temperature molten salt media

2007-04-01

214

Observation of Fluorescence for some lanthanides in LiCl-KCl molten salt media at high temperature  

Energy Technology Data Exchange (ETDEWEB)

To our knowledge, the fluorescence studies of lanthanides in LiCl-KCl eutectic molten salt at a high temperature are not reported yet. The fluorescence of the lanthanide-ions was generally decreased when the temperature was increased. Moreover, the fluorescence of the lanthanides was strong when the sample was solidified to or from the melt. The temperature, where the fluorescence was decreased, was identified to be different depending on the species of the lanthanides and the substrates was considered to possibly be from quenching of the fluorescence due to either the collisions of melted samples induced by high temperature media or the re-absorption of fluorescence by the samples. Several comparison experiments were performed to explain and understand this phenomenon and improve the fluorescence. In this way, an on-line monitoring of chemical species and the concentration for lanthanides elements in molten salt media of pyrochemical process ...

2008-08-15

215

Micro-analysis of ?salt weathering? on cement paste  

British Library Electronic Table of Contents (United Kingdom)

Normally, concrete technologists attribute salt weathering, salt crystallization or physical attack to the deterioration of concrete that is partially exposed to sulfate environment. However, there are few convincing evidences supporting this view. The purpose of this paper is to check by means of extensive micro-analysis if traces of sulfate crystals are present in the paste. This would enable to verify in a direct way whether salt weathering really causes cement paste damage or not.In this research, cement paste and cement?fly ash paste specimens were partially exposed to sodium sulfate and magnesium sulfates solution under a constant storage condition (20 ? 2 ?C, and 60 ? 5% RH) and a sharply fluctuating environment (40 ? 2 ?C and 35 ? 5% RH for 24 h, then 10 ? 1 ?C and 85 ? 5% RH, also...

2011-01-01

216

Influence of salt and elevated-temperature exposure on the maximum ...  

Science.gov (United States)

Ultimate Compressive Strength of Short Sheet - Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and Stringer ...

217

Identification of Metal Ion Chloro Complexes in an Ambient ...  

Science.gov (United States)

... a given ternary molten salt system under conditions which are greatly " different than the normal method of potentiometric titration, that is, high ...

1985-05-25

218

Harmonized Tariff Schedule Codes Flagged with Prior Notice ...  

Science.gov (United States)

... 3004505040***, MEDICAMENTS, DOSED, VITAMINS, MULTIPLE, OTHER COMBINATIONS, FD3***. 3104100000**, CARNALLITE, SYLVITE AND OTHER CRUDE POTASSIUM SALTS, FD3**. ...

219

Estimation of thermodynamic properties of the ternary molten salt system, LiF-NaF-BeF2, by the modified Peng-Robinson equation  

British Library Electronic Table of Contents (United Kingdom)

The molten salt reactor (MSR), which is one of the generation IV reactors, can meet the demand of transmutation and breeding. The thermodynamic properties of the molten salt system like LiF-NaF-BeF2 influence the design and construction of the fuel salt and coolant in the MSR for the new generation. In this paper, the equation of state of the ternary system 15%LiF-58%NaF-27%BeF2, over the temperature range from 873.15 to 1 073.15 K at one atmosphere pressure, is described using a modified Peng-Robinson (PR) equation. The densities of the ternary system and its components are estimated by this equation directly, and compared with the experimental data. Based on the equation of state, the other thermodynamic properties such as the enthalpy, entropy and heat capacity at constant pressure are ...

2007-01-01

220

Diffusivity and Absorptivity of EuCl3 in a LiCl-KCl Molten Salt  

Energy Technology Data Exchange (ETDEWEB)

Pyrochemical processing of nuclear fuels using molten salts has attracted much attention because of its potential to be applied for a future spent nuclear fuel management. In the pyrochemical processing, there are a number of steps to electro-refine and electro-win each element of lanthanides and actinides, commonly called trans-uranic elements (TRU). In order to materialize the pyrochemical processing in the nuclear power plant environments, qualitatively and quantitatively monitoring of each elements is necessary. Thus, we have undertaken to develop an on-line observing system of the TRU in LiCl-KCl molten salt media by using electrochemical and spectroscopic methods. In this work, the electrochemical and spectroscopic behaviors of europium as a proxy material for TRU were investigated simultaneously in the LiCl-KCl molten salt.

2009-05-15

221

Diffusivity and Absorptivity of EuCl3 in a LiCl-KCl Molten Salt  

International Nuclear Information System (INIS)

Pyrochemical processing of nuclear fuels using molten salts has attracted much attention because of its potential to be applied for a future spent nuclear fuel management. In the pyrochemical processing, there are a number of steps to electro-refine and electro-win each element of lanthanides and actinides, commonly called trans-uranic elements (TRU). In order to materialize the pyrochemical processing in the nuclear power plant environments, qualitatively and quantitatively monitoring of each elements is necessary. Thus, we have undertaken to develop an on-line observing system of the TRU in LiCl-KCl molten salt media by using electrochemical and spectroscopic methods. In this work, the electrochemical and spectroscopic behaviors of europium as a proxy material for TRU were investigated simultaneously in the LiCl-KCl molten salt

2009-05-01

222

Diagnostics of Radionuclides Effects Results  

International Science & Technology Center (ISTC)

Development of New Methods and Means of Assessing of Consequences of Radionuclide and Heavy Metal Salt Effect, Criteria of Forecasting Physiological State and Productivity of the Farm Animals under Conditions of Ecological Pollution of Environment

223

DOE - Office of Nuclear Energy  

Science.gov (United States)

Interactions (FCCI) University of Wisconsin, Madison Thermal Properties of LiCl-KCl Molten Salt for Nuclear Waste Separation University of Wisconsin, Madison Next Generation...

2011-03-23

224

A novel electrochemical alkylation of aniline with methanol over Zn/Cu salts modified kaolin  

British Library Electronic Table of Contents (United Kingdom)

A novel liquid phase alkylation of aniline with methanol over Zn/Cu salts modified kaolin assisted with a pair of porous carbon electrode in slurry-bed reactor under constant current intensity, room temperature and atmospheric pressure was reported. The Zn/Cu salts modified kaolin catalysts were synthesized and characterized by infrared spectrometer (IR), powder X-ray diffraction (XRD) and scanning electron microscopy (SEM), which showed that the transition metals were completely supported on kaolins structure and formed a pored one. The effect parameters, such as initial pH, electrolysis time, metal ratio with kaolin and salts composition in this electrochemical catalytic system, were studied. The procedure was inspected by ultraviolet-visible spectrum (UV-vis), and the product distributi...

2008-01-01

225

Snow Survey & Water Supply | NRCS  

Science.gov (United States)

Programs & Services Technical Resources Land Use Soils Water Snow Survey & Water Supply Water Management Water Quality Watersheds Wetlands Air Plants & Animals Energy Climate...

2011-08-21

226

Use of microbes for paraffin cleanup at Naval Petroleum Reserve No. 3  

Energy Technology Data Exchange (ETDEWEB)

Naval Petroleum Reserve No. 3 (NPR-3), also known as Teapot Dome, is a government-owned oil field in Natrona County, Wyoming. It is an asymmetrical anticline located on the western edge of the Powder River Basin, just south of the Salt Creek Anticline. Production started in 1922, and today the field is a marginally economic stripper field with average production of less than 3 BOPD (0.5 m{sup 3}/D) per well. Total field production is about 1,800 BOPD (286 m{sup 3}/D). The Second Wall Creek Formation was waterflooded from 1979 until June 1992 with poor results due to the extensive natural fracture system in this sandstone unit. Since water injection ceased, reservoir pressure has declined to very low levels. Liquids extraction and reinjection of the gas produced from high-GOR wells along the gas-oil contact continues, but the average gas cap pressure has fallen to approximately 150 psi (1.03 MPa) from an original pressure of 1,120 psi (7.72 ...

1995-12-31

227

The Structure of the Amyloid-[beta] Peptide High-Affinity Copper II Binding Site in Alzheimer Disease  

Energy Technology Data Exchange (ETDEWEB)

Neurodegeneration observed in Alzheimer disease (AD) is believed to be related to the toxicity from reactive oxygen species (ROS) produced in the brain by the amyloid-{beta} (A{beta}) protein bound primarily to copper ions. The evidence for an oxidative stress role of A{beta}-Cu redox chemistry is still incomplete. Details of the copper binding site in A{beta} may be critical to the etiology of AD. Here we present the structure determined by combining x-ray absorption spectroscopy (XAS) and density functional theory analysis of A{beta} peptides complexed with Cu{sup 2+} in solution under a range of buffer conditions. Phosphate-buffered saline buffer salt (NaCl) concentration does not affect the high-affinity copper binding mode but alters the second coordination sphere. The XAS spectra for truncated and full-length A{beta}-Cu{sup 2+} peptides are similar. The novel distorted six-coordinated (3N3O) geometry around copper in the A{beta}-Cu{sup 2+} complexes include ...

2008-11-03

228

Technical description of parameters influencing the pH value of suspension absorbent used in flue gas desulfurization systems.  

Science.gov (United States)

As a result of the large limestone deposits available in Poland, the low cost of reagent acquisition for the largescale technological use and relatively well-documented processes of flue gas desulfurization (FGD) technologies based on limestone sorbent slurry, wet scrubbing desulfurization is a method of choice in Poland for flue gas treatment in energy production facilities, including power plants and industrial systems. The efficiency of FGD using the above method depends on several technological and kinetic parameters, particularly on the pH value of the sorbent (i.e., ground limestone suspended in water). Consequently, many studies in Poland and abroad address the impact of various parameters on the pH value of the sorbent suspension, such as the average diameter of sorbent particles (related to the limestone pulverization degree), sorbent quality (in terms of pure calcium carbonate [CaCO3] content of the sorbent material), stoichiometric surfeit of CaCO3 in ...

2010-08-01

229

Off-gas behavior in the HARVEST pot vitrification process  

Energy Technology Data Exchange (ETDEWEB)

A summary of the off-gas behavior in the HARVEST pot vitrification process is presented. Experimental runs were carried out on 3 representative wastes (MAGNOX - thermal reactor, metal fuel, THORP - thermal oxide fuel and PFR - fast reactor oxide fuel) using 2 methods of feeding the glass-formers (slurry and crizzle). Materials were carried over from the vitrification vessel into the off-gas system by entrainment supplemented by volatilization. The main volatile elements were Ru, B, Cs. Some volatility was also shown by Na and Li. The overall behavior of the off-gas was consistent with the presence in it of 5 separate aerosols of particulate matter. Sources of entrainment gave rise to 3 aerosols, and a further 2 aerosols were formed as a result of chemical reaction (Ru) and condensation (Cs) proceses involving the volatile species. Entrainment was enhanced when the feed contained free alkali nitrate. The Ru volatility correlated directly with the amount of salt ...

1983-06-01

230

Near-real time infrared observations of acidic sulfates in /open quotes/clean/close quotes/ air at Mauna Loa, Hawaii  

Energy Technology Data Exchange (ETDEWEB)

Sulfuric acid and its partially or completely neutralized salts with ammonia are believed to result from the oxidation of sulfur dioxide in cloud water and in other heterogeneous media present in the atmosphere. Due to the natural abundance of ammonia and the ubiquitous presence of sulfur in the atmosphere, (NH/sub 4/)/sub 2/SO/sub 4/ is commonly the dominant chemical species in the ambient aerosol. The amounts of ammonium sulfates are expected to be very low in areas far removed from anthropogenic emissions of sulfur dioxide. The chemical composition of submicrometer aerosol particles was determined at the Mauna Loa Observatory (MLO) on Mauna Loa in Hawaii during an eight-day period in August 1986. The MLO site was selected for this measurement because it is the only ground-based aerosol observatory in the remote Pacific Ocean that allows extended sampling of aerosols in the free troposphere. Measurements were made using an attenuated total ...

1988-01-01

231

Influences of species of metals and supports on the hydrogenation activity of carbon-supported metal sulfides catalysts; Tanso biryushi tanji shokubai no suisoka kassei ni taisuru kassei kinzoku oyobi tantaishu no eikyo  

Energy Technology Data Exchange (ETDEWEB)

In order to design catalysts suitable for primary liquefaction stage and secondary upgrading stage respectively in the multi-stage liquefaction process, various carbon-supported catalysts were prepared. Catalytic activities of them were investigated for the hydrogenation of 1-methylnaphthalene, to discuss the influences of metals and carbon species on the catalytic activity. Various water soluble and oil soluble Mo and Ni salts were used for NiMo supported catalysts. Among various carbon supports, Ketjen Black (KB) was effective for preparing the catalyst showing the most excellent hydrogenation activity. The KB and Black Pearl 2000 (BP2000) showing high hydrogenation activity were fine particles having high specific surface area more than 1000 m{sup 2}/g and primary particle diameter around 30 nm. This was inferred to contribute to the high dispersion support of active metals. Since such fine particles of carbon exhibited hydrophobic surface, ...

1996-10-28

232

Depositional setting of the Upper Jurassic Hith Anhydrite of the Arabian Gulf: An analog to holocene evaporites of the United Arab Emirates and Lake MacLeod of Western Australia  

Energy Technology Data Exchange (ETDEWEB)

The Upper Jurassic Hith Anhydrite is a major hydrocarbon seal in the Arabian Gulf region. Outcrops, core samples from the subsurface, and the literature indicate that the Hith Formation is composed mainly of anhydrite. In most locations where a section of the Hith Formation has been measured, this unit contains less than 20% carbonate much of which is in the form of thin laminations. This lack of carbonate, locally thick layers of salt, and the predominance of anhydrite favor a playa for the setting in which this sediment was accumulated. In fact, much of the Hith has the sedimentary characteristics of the Holocene Lake MacLeod playa of Western Australia, which is dominated by layers of gypsum and halite (what little carbonate that occurs is found in layers at the base of the section). Locally the Hith appears to have accumulated in a sabkha setting, particularly toward central Abu Dhabi where it pinches out into shallow-water, and peritidal ...

1994-07-01

233

WASTE DISPOSAL IN SALT. I. THE HNO$sub 3$-NaCl REACTION  

Science.gov (United States)

The chemical reaction between nitric acid and sodium chloride was investigated in onder to provide preliminary information for subsequent studies on the interaction between simulated Purex waste solution and salt. The reaction is characterized by the production of chlorine and nitrosyl chloride and can be considered to be the same as the aqua regia reaction. Within the limits of the conditions imposed by the projected field studies, the acid concentration and temperature are the two parameters which control the extent of the interaction. (auth)

1960-10-01

234

Use of alkali nitrate molten salts as electrolytes in intermediate temperature lithium batteries  

Energy Technology Data Exchange (ETDEWEB)

Advanced lithium batteries presently under development operate either at the high temperatures associated with the LiCl-KCl molten salt (350-450/degree/C), or at ambient temperatures employing organic solvent based electrolytes. An intermediate temperature lithium battery is proposed as an alternative if it reduces corrosion problems present at high temperatures and improved kinetic performance with respect to ambient temperature cells. 17 refs.

1981-01-01

235

Phosphorus-containing catalyst and catalytic cracking process utilizing the same  

Energy Technology Data Exchange (ETDEWEB)

A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with an anion such as a dihydrogen phosphate anion or a dihydrogen phosphite anion and additionally with an ammonium salt other than a salt of an inorganic acid of phosphorus. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.

1985-03-12

236

Multi-mode wavepath depth imaging for the SEG/EAGE salt model  

Energy Technology Data Exchange (ETDEWEB)

Elastic depth imaging of both P-wave and S-wave prestack seismic reflection data is formulated as a degraded form of Kirchhoff migration known as Wavepath Migration (WM). Applications to the SEG/EAGE salt model show that the method is sufficiently versatile anti relaitively inexpensive. It handles S-wave data with at least the same accuracy as Pwave data when local mode conversions are removed. WM also provides an understanding of multi-mode illumination.

2003-01-01

237

Hydrocarbon cracking catalysts and processes for utilizing the same  

Energy Technology Data Exchange (ETDEWEB)

This patent describes a catalyst comprising: (a) a non-zeolitic inorganic oxide matrix, and (b) an ultrastable Y-type crystalline zeolite, the ziolite having been pretreated by contacting the zeolite with a phosphorus compound selected from the group consisting of phosphoric acid, phosphorous acid, a salt of phosphoric acid, a salt of phosphorous acid, and mixtures thereof for a time sufficient to composite an effective amount of phosphorus with the zeolite.

1989-06-13

238

Dispersed alkali elements in minerals and products of natural salts processing  

International Nuclear Information System (INIS)

Distribution of scattered elements in basic minerals of salt-rocks is studied. It is shown that rubidium and cesium are accumulated mainly in carnallites and are contained in small quantities halites. These elements are accumulated primarily in the carnallite production products, wherein their content in a number of cases exceeds by dozens and hundred times their content in source rocks. It is noted that only carnallites may be considered in the list of actual sources for rubidium and cesium separation

1995-06-01

239

Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes  

Energy Technology Data Exchange (ETDEWEB)

Molten salt oxidation (MSO) is proposed as a {sup 238}Pu waste treatment technology that should be developed for volume reduction and recovery of {sup 238}Pu and as an alternative to the transport and permanent disposal of {sup 238}Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious {sup 238}Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums ...

1998-05-01

240

Adsorption of di-2-ethylhexylphosphoric acid from toluene the interface with inorganic salt aqueous solutions  

International Nuclear Information System (INIS)

Interfacial tension in the system toluene solution of di-2-ethylhexylphosphoric acid HDEHP-aqueous solutions of inorganic salts has been measured by the drop volume method. The ion-exchange constants in the monolayers formed by HDEHP and alkaline-earth metals have been measured.

241

Surface modification, organometallic and polyaryl polymer coatings, and flame spray technologies for preventing corrosion of metals. Final report  

Energy Technology Data Exchange (ETDEWEB)

To improve adherent properties of electrogalvanized steel (EGS) to polymeric topcoats, the surfaces of EGS were modified by polyelectrolyte-modified zinc phosphating solution. The electrochemical reaction between phosphating solution and EGS led to the complete coverage with fully grown hopeite crystals after only 5 sec treatment, thereby improving adhesion to topcoating and providing protection of EGS against corrosion. To evaluate the ability of polyphenylene sulfide (PPS) polyaryl thermoplastic coatings to protect zinc phosphate (Zn{center_dot}Ph)treated steels from corrosion in a wet, harsh environment ( 1.0 wt % H{sub 2}SO{sub 4}, 3.0 wt % NaCl and 96.0 wt % water at temperatures from 25{degrees} to 200{degree}C), we exposed them in an autoclave to attempt heating-cooling cyclic fatigue tests (1 cycle = 12 hr at 200{degrees}C + 12 hr at 25{degrees}C) up to 90 times. The major chemical reaction at the interface between the PPS and Zn in the Zn-Ph layer during ...

1995-07-01

242

Synthesis of alkylated deoxyno irimycin and 1,5-dideoxy-1,5-iminoxylitol analogues: : Polar side-chain modification, sulfonium and selenonium heteroatom variants, conformational analysis, and evaluation as glycosidase inhibitors  

DEFF Research Database (Denmark)

The syntheses of N-alkylated deoxynojirimycin and 1,5-dideoxy-1,5-iminoxylitol derivatives having either a D- or an L-erythritol-3-sulfate functionalized N-substituent are reported. The alkylating agent used was a cyclic sulfate derivative, whereby selective attack of the nitrogen atom at the least hindered primary center afforded the desired ammonium salt. In aqueous solution, these salts were configurationally labile at the ammonium center. Sulfonium and/or selenonium analogues of the ammonium salts were prepared by analogous reactions. The chalcogen salts were obtained as mixtures of diastereomers, separable in some cases, differing only in the stereochemistry at the configurationally stable sulfur or selenium atoms. Proof of configuration and conformation of each compound was obtained by detailed NMR experiments. The compounds are six-membered ring analogues of salacinol, a known ...

2004-01-01

243

Salt repository project closeout status report  

Energy Technology Data Exchange (ETDEWEB)

This report provides an overview of the scope and status of the US Department of Energy (DOE`s) Salt Repository Project (SRP) at the time when the project was terminated by the Nuclear Waste Policy Amendments Act of 1987. The report reviews the 10-year program of siting a geologic repository for high-level nuclear waste in rock salt formations. Its purpose is to aid persons interested in the information developed during the course of this effort. Each area is briefly described and the major items of information are noted. This report, the three salt Environmental Assessments, and the Site Characterization Plan are the suggested starting points for any search of the literature and information developed by the program participants. Prior to termination, DOE was preparing to characterize three candidate sites for the first mined geologic repository for the permanent disposal of high-level nuclear waste. The sites were in ...

1988-06-01

244

Organic-inorganic mixtures for solar energy storage systems  

Energy Technology Data Exchange (ETDEWEB)

Mixtures of organic-inorganic substances are studied for their performance as energy storage media. Use is made of the fact that organic substances give higher amounts of energy but within a wide range of temperature on the one side and the fact that inorganic substances give lower amounts of energy at constant temperature on the other side. Mixtures of both types of substances, in different ratios, are investigated for the object of determining that optimum composition which stores a higher amount of energy and, meanwhile, releases it at a constant temperature or within a narrow range of temperature. The mixtures used are composed of Glauber`s salt (Na{sub 2}SO{sub 4}.10H{sub 2}O) and stearic acid in different proportions. The effect of cooling fluid flow rate and ambient temperature as well as the effect of addition of a nucleating agent is studied. The results showed that the highest amount of energy stored could be obtained from a mixture containing 40% stearic ...

1995-10-01

245

Measurements of radio propagation in rock salt for the detection of high-energy neutrinos  

CERN Document Server

We present measurements of the transmission of radio/microwave pulses through salt in the Cote Blanche salt mine operated by the North American Salt Company in St. Mary Parish, Louisiana. These results are from data taken in the southwestern region of the 1500 ft. (457 m) deep level of the mine on our third and most recent visit to the mine. We transmitted and received a fast, high-power, broadband pulse from within three vertical boreholes that were drilled to depths of 100 ft. (30 m) and 200 ft. below the 1500 ft. level using three different pairs of dipole antennas whose bandwidths span 125 to 900 MHz. By measuring the relative strength of the received pulses between boreholes with separations of 50 m and 169 m, we deduce the attenuation of the signal attributed to the salt medium. We fit the frequency dependence of the attenuation to a power law and find the best fit field attenuation lengths to be ...

2008-01-01

246

Electrometallurgical treatment of aluminum-matrix fuels  

Energy Technology Data Exchange (ETDEWEB)

The electrometallurgical treatment process described in this paper builds on our experience in treating spent fuel from the Experimental Breeder Reactor (EBR-II). The work is also to some degree, a spin-off from applying electrometallurgical treatment to spent fuel from the Hanford single pass reactors (SPRs) and fuel and flush salt from the Molten Salt Reactor Experiment (MSRE) in treating EBR-II fuel, we recover the actinides from a uranium-zirconium fuel by electrorefining the uranium out of the chopped fuel. With SPR fuel, uranium is electrorefined out of the aluminum cladding. Both of these processes are conducted in a LiCl-KCl molten-salt electrolyte. In the case of the MSRE, which used a fluoride salt-based fuel, uranium in this salt is recovered through a series of electrochemical reductions. Recovering high-purity uranium from an aluminum-matrix fuel is more challenging ...

1996-08-01

247

Comparative study of seed germination and growth of Kochia prostrata and Kochia scoparia (Chenopodiaceae) under salinity  

British Library Electronic Table of Contents (United Kingdom)

Soils of arid regions of Central Asia contain salts of different types that may differentially affect seed germination and plant development. We studied effect of NaCl, Na2SO4, 2NaCl + KCl + CaCl2 and 2Na2SO4+K2SO4+MgSO4 on germination of Kochia prostrata and Kochia scoparia seeds under a range of concentrations from 0.5 to 5% and at two constant temperature regimes +22 degrees C and +6 degrees C. The observed salt tolerance limit of germination at constant temperature +22 degrees C for both species was 5-6%, while at low temperature (+6 degrees C) this limit was 2%. The salt tolerance of young plants (before flowering) was 3% for NaCl. Low concentrations of sulfuric and mixed salts had a stimulating effect on seed germination in K. prostrata. Despite similarity of salt-tolerance limits...

2011-01-01

248

Uranium-lead zircon ages from the Median Tectonic Zone, New Zealand  

International Nuclear Information System (INIS)

The Median Tectonic Zone (MTZ) of New Zealand is a generally north trending belt of Mesozoic subduction related I-type plutonic, volcanic, and sedimentary rocks in South Island and Stewart Island that separates Permian strata of the Eastern Province Brook Street Terrane from lower to mid Gondwana margin assemblages of the Western Province. High precision isotope dilution U/Pb ages of zircons from 30 rocks are reported. Pre-digestion leaching of zircon in hydrofluoric acid yielded significantly more concordant residues by removing common Pb and dissolving more soluble high-U domains that have been more affected by relatively recent Pb loss. The results show that MTZ magmatism ranges in age from at least Early Triassic to Early Cretaceous (247-131 Ma), with a pronounced gap in the Middle Jurassic. Triassic plutons tend to occur on the eastern side of the MTZ, and they intrude volcanic/sedimentary sequences of the MTZ in Nelson and eastern Fiordland. These sequences are in turn intruded ...

249

Thrust faults and associated structures in the Deep River Basin: Evidence for post-extensional compression  

Energy Technology Data Exchange (ETDEWEB)

Thrust faulting, folding, and penetrative compressional fabrics (e.g. spaced cleavage, pencils, and coal cleats) have been found in several outcrops within the central Deep River Basin (the southern Durham subbasin to the northern Wadesboro subbasin). The trend of these structures is nearly parallel to the basin, and may locally control the present geometry of the basin boundaries. These features are distributed throughout the stratigraphic section and across the entire width of the basin. In outcrops where relative timing can be determined, the compressional structures post-date all extensional and intrusive features associated with basin formation. In particular, thrusts cut across and displace basin-parallel normal faults and basin-normal cross-faults. All thrusts found to date verge northwest, and displacements of cross-fault boundaries indicate that transport was approximately 325[degree].

1994-03-01

250

Supporting Dynamic Ad hoc Collaboration Capabilities  

CERN Document Server

Modern HENP experiments such as CMS and Atlas involve as many as 2000 collaborators around the world. Collaborations this large will be unable to meet often enough to support working closely together. Many of the tools currently available for collaboration focus on heavy-weight applications such as videoconferencing tools. While these are important, there is a more basic need for tools that support connecting physicists to work together on an ad hoc or continuous basis. Tools that support the day-to-day connectivity and underlying needs of a group of collaborators are important for providing light-weight, non-intrusive, and flexible ways to work collaboratively. Some example tools include messaging, file-sharing, and shared plot viewers. An important component of the environment is a scalable underlying communication framework. In this paper we will describe our current progress on building a dynamic and ad hoc collaboration environment and our vision for its ...

2003-01-01

251

Sea-level rise and coastal zone management  

Energy Technology Data Exchange (ETDEWEB)

Greenhouse-effect induced climate change repercussions will, via the catchment areas of big rivers, eventually arrive in amplified form at the far downstream coastal zones of the world. In the coastal zone these imported problems will add to the locally exerted climate change effects, while the climate change induced sea-level rise will attack the coastal zone from the other side, both by flooding and by saline groundwater intrusion. These multiple problems will hit the coastal zone, which is already under increasing stress. The combined threats require fast and massive support for national Coastal Zone Management capabilities, which could help to limit the damage and to support planning for sustainable development. Recommendations are presented to facilitate implementation of Coastal Zone Management units in all coastal countries by the year 2000.

1992-09-01

252

Recycling and ?re-hydration? of degassed magma inducing transient dissolution/crystallization events at Stromboli (Italy)  

British Library Electronic Table of Contents (United Kingdom)

Intrusive degassing and recycling of degassed and dense magma at depth have been proposed for a long time at Stromboli. The brief explosive event that occurred at the summit craters on 9 January 2005 threw out bombs and lapilli that could be good candidates to illustrate recycling of shallow degassed magma at depth. We present an extensive data set on both the textures and the mineral, bulk rock and glassy matrix chemistry of the ?9 Jan? products. The latter have the common shoshonitic?basaltic bulk composition of lavas and scoriae issued from typical strombolian activity. In contrast they differ by the heterogeneous chemistry of their matrix glasses and their crystal textures that testify to crystal dissolution event(s) just prior magma crystallization upon ascent and eruption. Comparison...

2008-01-01

253

Proterozoic kimberlites and lamproites and a preliminary age for the Argyle lamproite pipe, Western Australia  

International Nuclear Information System (INIS)

The Argyle pipe occurring in the East Kimberley Province of Western Australia is a unique, highly-diamondiferous lamproite. Although it resembles other lamproites located in the West Kimberley Province with respect to its setting, structure, petrography and geochemistry, it is probably Proterozoic in age and hence substantially older than Tertiary occurrences of the West Kimberley Province. Rb-Sr measurements on whole rock and phlogopite samples from magmatic olivine-phlogopite lamproite, reveals a two point model age of 1126 +- 9 Ma for the Argyle pipe. This age is consistent with ages of other, similar volcanic igneous rocks occurring in several localities worldwide. The widespread occurrence of Proterozoic kimberlites and lamproites suggests that this was an important period of worldwide alkalic intrusive activity.

254

High resolution gamma-ray spectrometry of culverts containing transuranic waste at the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

A number of concrete culverts used to retrievably store drummed, dry, radioactive waste at the Savannah River Site (SRS), were suspected of containing ambiguous quantities of transuranic (TRU) nuclides. These culverts were assayed in place for Pu-239 content using thermal and fast neutron counting techniques. High resolution gamma-ray spectroscopy on 17 culverts, having neutron emission rates several times higher than expected, showed characteristic gamma-ray signatures of neutron emitters other than Pu-239 (e.g., Pu-238, Pu/Be, or Am/Be neutron sources). This study confirmed the Pu-239 content of the culverts with anomalous neutron rates and established limits on the Pu-239 mass in each of the 17 suspect culverts by in-field, non-intrusive gamma-ray measurements.

1990-01-01

255

High resolution gamma-ray spectrometry of culverts containing transuranic waste at the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

A number of concrete culverts used to retrievably store drummed, dry, radioactive waste at the Savannah River Site (SRS), were suspected of containing ambiguous quantities of transuranic (TRU) nuclides. These culverts were assayed in place for Pu-239 content using thermal and fast neutron counting techniques. High resolution gamma-ray spectroscopy on 17 culverts, having neutron emission rates several times higher than expected, showed characteristic gamma-ray signatures of neutron emitters other than Pu-239 (e.g., Pu-238, Pu/Be, or Am/Be neutron sources). This study confirmed the Pu-239 content of the culverts with anomalous neutron rates and established limits on the Pu-239 mass in each of the 17 suspect culverts by in-field, non-intrusive gamma-ray measurements.

1990-12-31

256

Development of a waterjet system for direct delivery of granular iron and activated carbon to remediate contaminated aqueous sediments  

British Library Electronic Table of Contents (United Kingdom)

Abstract While the techniques and technologies associated with contaminated sediment remediation are relatively mature, there are several issues associated with these practices that make them unattractive. The inability of currently used mechanical mixing implements to place amendments in aqueous environments and their intrusive behavior toward benthic communities are just two examples of a necessity for an improved delivery method. Waterjets may be a viable option for placement of particulate remediation amendments, such as activated carbon and granular iron, at depth. A custom waterjet nozzle and injection system has been fabricated by the authors to examine this delivery concept. The developed injection system's performance was tested by characterizing the waterjet-delivered amendment (...

2011-01-01

257

Characteristics of oxidation reaction of rare-earth chlorides for precipitation in LiCl-KCl molten salt by oxygen sparging  

International Nuclear Information System (INIS)

The precipitation reaction of some rare earth chlorides (La/Ce/Nd/GdCl3) in a LiCl-KCl molten salt has been carried out by using the oxygen sparging method. In this study, regardless of the oxygen sparging time and the molten salt temperature, oxychlorides (REOCl) for LaCl3, NdCl3 and GdCl3, and an oxide (REO2) for CeCl3 are formed as a precipitate. The conversion of rare-earth chlorides into insoluble precipitates was described by using a conversion ratio. The conversion ratio increased exponentially with the oxygen sparging time and finally showed asymptotic value at 1,023K of the molten salt temperature condition. The conversion ratios of LaCl3, NdCl3 and GdCl3 were increased with the molten salt temperature, however, even though the conversion ratio was increased from 0.660 to 0.995 with increasing molten salt temperature from 823 to 923 K at 60 min of a sparging time, the ...

2006-10-01

258

Water Quality Criteria | Water Quality Criteria | US EPA  

Science.gov (United States)

for? Learn the Issues Science & Technology Laws & Regulations About EPA Contact Us Water: Water Quality Criteria You are here: Water Science & Technology Surface Water Standards &...

2011-08-28

259

Characterization of the deviation of the ideality of concentrated electrolytic solutions: plutonium 4 and uranium 4 nitrate salts study; Contribution a la caracterisation de l'ecart a l'idealite des solutions concentrees d'electrolytes: application aux cas de nitrates de plutonium (4) et d'uranium (4)  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work was to establish a new binary data base by compiling the activity coefficients of plutonium and uranium at oxidation state +IV to better account for media effects in the liquid-liquid extraction operations implemented to reprocess spent nuclear fuel. Chapter 1: first reviews the basic thermodynamic concepts before describing the issues involved in acquiring binary data for the tetravalent actinides. The difficulties arise from two characteristics of this type of electrolyte: its radioactive properties (high specific activity requiring nuclearization of the experimental instrumentation) and its physicochemical properties (strong hydrolysis). After defining the notion of fictive binary data, an approach based on the thermodynamic concept of simple solutions is described in which the activity coefficient of an aqueous phase constituent is dependent on two parameters: the water activity of the system and the total concentration of dissolved ...

2000-07-01

262

The solubilities of significant organic compounds in HLW tank supernate solutions  

International Nuclear Information System (INIS)

Large quantities of organic chemicals used in reprocessing spent nuclear-fuels at the Hanford Site have accumulated in underground high-level radioactive waste tanks. The organic content of these tanks must he known so that the potential for hazardous reactions between organic components and sodium nitrate/nitrite salts in the waste can he evaluated. The solubilities of organic compounds described in this report will help determine if they are present in the solid phases (salt cake and sludges) as well as the liquid phase (interstitial liquor/supernate) in the tanks. The solubilities of five significant sodium salts of carboxylic acids and aminocarboxylic acids [sodium oxalate, formate, citrate, nitrilotriacetate (NTA) and ethylendiaminetetraacetate (EDTA)] were measured in a simulated supernate solution at 25 degrees C, 30 degrees C, 40 degrees C, and 50 degrees C.

1994-08-21

263

Neutron powder diffraction and solid-state deuterium NMR studies of Ca{sub 2}RuD{sub 6} and the stability of transition metal hexahydride salts  

Energy Technology Data Exchange (ETDEWEB)

The crystal structure of Ca{sub 2}RuD{sub 6} has been determined by neutron powder diffraction: space group Fm3m, K{sub 2}PtCl{sub 6} structure, as found for other hexahydride salts of group 8 metals with alkaline earth or lanthanide counter ions. No structural phase transition was observed between 340 K and 50 K. The deuterium nuclear quadrupole coupling constant, 54.7 kHz, leads to an ionic character of the Ru-D bond of 76%. The known trends in the behaviour of A{sub 2}MH{sub 6} salts are interpreted in terms of the ionization energies of the cation and the central metal atom.

2008-07-28

264

Neutron powder diffraction and solid-state deuterium NMR studies of Ca2RuD6 and the stability of transition metal hexahydride salts  

British Library Electronic Table of Contents (United Kingdom)

The crystal structure of Ca2RuD6 has been determined by neutron powder diffraction: space group Fm3m, K2PtCl6 structure, as found for other hexahydride salts of group 8 metals with alkaline earth or lanthanide counter ions. No structural phase transition was observed between 340K and 50K. The deuterium nuclear quadrupole coupling constant, 54.7kHz, leads to an ionic character of the Ru-D bond of 76%. The known trends in the behaviour of A2MH6 salts are interpreted in terms of the ionization energies of the cation and the central metal atom.

2008-01-01

265

EPR and luminescence studies of Eu(II) magnetically diluted in LiCl-KCl salt  

Energy Technology Data Exchange (ETDEWEB)

High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723 K by using Eu{sub 2}O{sub 3} as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723 K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.

2007-12-15

266

EPR and luminescence studies of Eu(II) magnetically diluted in LiCl-KCl salt  

International Nuclear Information System (INIS)

High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723 K by using Eu_2O_3 as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723 K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.

2007-12-01

267

EPR and luminescence studies of Eu(II) magnetically diluted in LiCl-KCl salt  

British Library Electronic Table of Contents (United Kingdom)

High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723K by using Eu2O3 as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.

2007-01-01

268

Chemical aspects of the trapping and recovery of uranium hexafluoride and fluorine during remediation activities  

Energy Technology Data Exchange (ETDEWEB)

Decontamination and decommission activities related to the Molten Salt Reactor Experiment (MSRE) involve the trapping and recovery of radiolitically generated uranium hexafluoride and fluorine. Although fission product radiolysis was known to generate F{sub 2}, the formation of UF{sub 6} and its transport from the fuel salt was unexpected. Some of these gaseous radiolysis products have been moving through the gas piping to a charcoal bed since the reactor was shut down in 1969. Current and planned remediation and clean-up activities involve the trapping of the gaseous products, deactivation and treatment of the activated charcoal bed, stabilization and reconditioning of the fuel salt, and recovery of the uranium. The chemical aspects of these processes, including radiolytic generation mechanisms, reactions between uranium hexafluoride and fluorine and trapping materials such as activated charcoal, activated alumina, and ...

1996-10-01

269

Adsorption Kinetics of Surfactants at Fluid-Fluid Interfaces  

CERN Document Server

We review a new theoretical approach to the kinetics of surfactant adsorption at fluid-fluid interfaces. It yields a more complete description of the kinetics both in the aqueous solution and at the interface, deriving all equations from a free-energy functional. It also provides a general method to calculate dynamic surface tensions. For non-ionic surfactants the results coincide with previous models. Common non-ionic surfactants are shown to undergo diffusion-limited adsorption, in agreement with experiments. Strong electrostatic interactions in salt-free ionic surfactant solutions are found to lead to kinetically limited adsorption. In this case the theory accounts for unusual experimental results which could not be understood using previous approaches. Added salt screens the electrostatic interactions and makes the ionic surfactant adsorption similar to the non-ionic case. The departure from the non-ionic behavior as the ...

1997-01-01

270

A method for preventing cathodic deposition of molybdenum subchloride in LiCl-KCl molten salt  

Energy Technology Data Exchange (ETDEWEB)

Effects of ions of Group IA, IIA, IIIB, and VIIB elements on the cathodic deposition of a molybdenum were investigated in a KCl-LiCl (eutectic)-MoCl/sub 3/ molten salt at 773 K (500/degree/C). The results can be summarized as follows: The addition of potassium, rubidium, cesium, and barium cations and fluorine anions to the KCl-LiCl (eutectic)-MoCl/sub 3/ molten salt is effective in depressing the cathodic deposition of the molybdenum subchloride, which hinders the smooth, flat electrodeposition of molybdenum. The addition of lithium, sodium, magnesium, calcium, strontium, and aluminum cations and bromine and iodine anions promotes the undesirable cathodic deposition of the molybdenum subchloride.

1989-01-01

271

Photocatalytic oxidation and reduction chemistry and a new process for treatment of pink water and related contaminated water  

Energy Technology Data Exchange (ETDEWEB)

The objective of this project was to develop new photocatalytic or other innovative process chemistry for the treatment of pink water and related contaminated water.

1996-10-01

272

Reintrusion of silicic magma chambers by mafic dike complex: evidence from the northern Semail ophiolite  

Energy Technology Data Exchange (ETDEWEB)

Late plagiogranite bodies in the Semail ophiolite have been previously suggested to represent late stage fractionates within an episodic spreading center magma chamber or the roots of seamount chains. Field and lab observations suggest that these late silicic magma chambers represent zones of repeated injection by dikes of intermediate to mafic composition. Multiple generations of intrusion, partial resorption and reintrusion are preserved in the plagiogranite as 1) relict phantom xenoliths, 2) angular xenoliths with quartz-rich margins, 3) deformed fine-grained dikes with distinct chilled margins, and 4) planes of rectangular blocks with cuspate margins or ellipsoids of similar fine grained mafic materials. The blocks and ellipsoids are actually dismembered mafic dikes that chilled by intruding a cooler silicic liquid and were either thermally fractured or pinched out. All of the dikes are hydrothermally altered to assemblages including amph., qtz., epi., preh., ...

1985-01-01

273

Lithology and evolution of the crust-mantle boundary region in the southwestern Basin and Range province  

Energy Technology Data Exchange (ETDEWEB)

Seismic transects in this area show a strongly reflective Moho of generally low relief, which, in the area of modern transects, consists of a thin zone (< 2 km thick) of short reflectors. The upper mantle is transparent and has a P{sub n} of 7.8-8.0 km/s similar to much of the western US. A lower crustal zone, 2-13 km thick, has variable internal reflectivity and a relatively low velocity of 6.6-6.8 km/s. Upper mantle peridotite xenoliths show both ductile and brittle deformational features and have structures and composition affected by magmatic intrusion; intrusions form complex dike systems and extensive zones of grain boundary infiltration in peridotite xenoliths. Whereas melt infiltration preceded and followed ductile deformation, brittle deformation, represented by closely spaced joint systems and faults, followed ductile deformation and is related to the youngest magmatic episodes. Lower crustal xenoliths are dominantly ...

1990-01-10

274

Ground penetrating radar and direct current resistivity evaluation of the desiccation test cap, Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) has a variety of waste units that may be temporarily or permanently stabilized by closure using an impermeable cover to prevent groundwater infiltration. The placement of an engineered kaolin clay layer over a waste unit is an accepted and economical technique for providing an impermeable cover but the long term stability and integrity of the clay in non-arid conditions is unknown. A simulated kaolin cap has been constructed at the SRA adjacent to the Burial Ground Complex. The cap is designed to evaluate the effects of desiccation on clay integrity, therefore half of the cap is covered with native soil to prevent drying, while the remainder of the cap is exposed. Measurements of the continuing impermeability of a clay cap are difficult because intrusive techniques may locally compromise the structure. Point measurements made to evaluate clay integrity, such as those from grid sampling or coring and made through a soil cover, may miss ...

1996-04-01

275

Granitoid formation is ineffective in isotopically homogenizing continental crust: Evidence from archean rocks of the Wind River Mountains, Wyoming  

Energy Technology Data Exchange (ETDEWEB)

The Archean core of the Laramide Wind River uplift records evidence of at least three major granitoid-forming episodes. The oldest, the Dry Creek gneiss (DCG), was emplaced by 2.8 Ga and occupies the northeastern part of the range. Mafic, pelitic and ultramafic inclusions occur in the DCG. Elsewhere in the Wind River Mountains there is evidence for crustal components as old as 3.8 Ga. The Bridger batholith (BB), intruded at 2.67 Ga, is found in the west-central Wind River Mountains. The Wind River batholith (WRB) refers to the youngest Late Archean granodiorites and granites which are found throughout the range and includes granitoids previously name the Louis Lake, Bears Ears, Popo Agie, and Middle Mountain intrusions. Although granitoids of the Wind River batholith have been dated at 2.63 and 2.55 Ga, they are considered together here because there is a complete gradation in rock type and because definite intrusive contacts are scarce. The ...

1992-01-01

276

Dike Propagation Near Drifts  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this Analysis and Model Report (AMR) supporting the Site Recommendation/License Application (SR/LA) for the Yucca Mountain Project is the development of elementary analyses of the interactions of a hypothetical dike with a repository drift (i.e., tunnel) and with the drift contents at the potential Yucca Mountain repository. This effort is intended to support the analysis of disruptive events for Total System Performance Assessment (TSPA). This AMR supports the Process Model Report (PMR) on disruptive events (CRWMS M&O 2000a). This purpose is documented in the development plan (DP) ''Coordinate Modeling of Dike Propagation Near Drifts Consequences for TSPA-SR/LA'' (CRWMS M&O 2000b). Evaluation of that Development Plan and the work to be conducted to prepare Interim Change Notice (ICN) 1 of this report, which now includes the design option of ''Open'' drifts, indicated that no revision ...

2002-03-04

277

Characterization of crystalline rocks in the Lake Superior region, USA: implications for nuclear waste isolation. [Wisconsin, Upper Peninsula of Michigan and Minnesota  

Energy Technology Data Exchange (ETDEWEB)

The Lake Superior region (Wisconsin, the Upper Peninsula of Michigan, and Minnesota) contains 41 Precambrian crystalline rock complexes comprising 64 individual but related rock bodies with known surface exposures. Each complex has a map area greater than 78 km/sup 2/. About 54% of the rock complexes have areas of up to 500 km/sup 2/, 15% fall between 500 km/sup 2/ and 1000 km/sup 2/, 19% lie between 1000 km/sup 2/ and 2500 km/sup 2/, and 12% are over 2500 km/sup 2/. Crystalline rocks of the region vary widely in composition, but they are predominantly granitic. Repeated thermo-tectonic events have produced early Archean gneisses, migmatites, and amphibolites with highly tectonized fabrics that impart a heterogeneous and anisotropic character to the rocks. Late Archean rocks are usually but not invariably gneissose and migmatitic. Proterozoic rocks of the region include synorogenic (foliated) granitic rocks, anorogenic (non-foliated) granites, and the layered ...

1984-01-01

278

Low-pH injection grout for deep repositories. Summary report from a co-operation project between NUMO (Japan), Posiva (Finland) and SKB (Sweden)  

Energy Technology Data Exchange (ETDEWEB)

The use of standard cementitious material creates pulses of pH in the magnitude of 12-13 in the leachates and release alkalis. Such a high pH is detrimental and also unnecessarily complicates the safety analysis of the repository. As no reliable pH-plume models exist, the use of products giving a pH below 11 in the leachates facilitates the safety analysis. Also, according to current understanding, the use of low-pH cement (pH = 11) will not disturb the functioning of the bentonite, although limiting the amount of low-pH cement is recommended. A result of the project is that there are both low-pH cementitious material for grouting larger fractures (= 100 {mu}m) and non-cementitious material for grouting smaller fractures (< 100 {mu}m) that will, after further optimisation work, be recommended for grouting of deep repositories. This project concentrated on the technical development of properties for the low pH grouts. Long-term safety and environmental aspects and durability of ...

2005-06-01

279

Water resources data for Oklahoma, water year 1992. Volume 2. Red River Basin. Water-data report (Annual), 1 October 1991-30 September 1992  

Energy Technology Data Exchange (ETDEWEB)

Volume 2 of the water resources data for the 1992 water year for Oklahoma consists of record of stage, discharge, and water quality of streams; stage, contents, and water quality of lakes or reservoirs; and water levels of ground-water well. The report contains discharge records for 136 gaging stations; stage and contents for 31 lakes or reservoirs; water quality for 50 gaging stations. Also included are 61 partial-record or miscellaneous streamflow stations and 28 ground-water sites.

1993-04-01

280

The influence of salt aerosol on alpha radiation detection by WIPP continuous air monitors  

Energy Technology Data Exchange (ETDEWEB)

Alpha continuous air monitors (CAMs) will be used at the Waste Isolation Pilot Plant (WIPP) to measure airborne transuranic radioactivity that might be present in air exhaust or in work-place areas. WIPP CAMs are important to health and safety because they are used to alert workers to airborne radioactivity, to actuate air-effluent filtration systems, and to detect airborne radioactivity so that the radioactivity can be confined in a limited area. In 1993, the Environmental Evaluation Group (EEG) reported that CAM operational performance was affected by salt aerosol, and subsequently, the WIPP CAM design and usage were modified. In this report, operational data and current theories on aerosol collection were reviewed to determine CAM quantitative performance limitations. Since 1993, the overall CAM performance appears to have improved, but anomalous alpha spectra are present when sampling-filter salt deposits are at normal to high levels. This ...

1996-01-01

281

The Mammalian Neuroendocrine Hormone Norepinephrine Supplies Iron for Bacterial Growth in the Presence of Transferrin or Lactoferrin  

UK PubMed Central (United Kingdom)

Norepinephrine stimulates the growth of a range of bacterial species in nutritionally poor SAPI minimal salts medium containing 30% serum. Addition of size-fractionated serum components to SAPI...Full Text Available

2000-11-01

282

The Effects of Temperature on the Labellar Chemoreceptors of the Blowfly  

UK PubMed Central (United Kingdom)

In the labellar chemosensory hairs of the blowfly, Phormia regina Meigen, stationary amplitudes of the slow potentials induced by salt and sugar stimulations were decreased to 50–80%...Full Text Available

1972-02-01

283

Sulphur petroleum coke as a highly effective reducing agent in the production of barite salts  

Science.gov (United States)

Describes laboratory and industrial tests on the use of lowasash sulphurous petroleum coke during reduction of barite. Shows the potential of substituting blast furnace coke with petroleum/coke fines in this process.

1980-01-01

284

Structural aspects of lithium ions hydration in aqueous solutions of electrolytes  

International Nuclear Information System (INIS)

Analysis of results of an investigation into the structure of lithium salt aqueous solutions is presented. An anomaly in lithium ion behaviour in solutions at the structural level is noted. 40 refs., 3 tabs.

285

Simulation tools and new developments of the molten salt fast reactor  

International Nuclear Information System (INIS)

Starting from the Molten Salt Breeder Reactor project of Oak-Ridge, we have performed parametric studies in terms of safety coefficients, reprocessing requirements and breeding capabilities. In the frame of this major re-evaluation of the molten salt reactor (MSR), we have developed a new concept called Molten Salt Fast Reactor or MSFR, based on the Thorium fuel cycle and a fast neutron spectrum. This concept has been selected for further studies by the MSR steering committee of the Generation IV International Forum in 2009. Our reactor's studies of the MSFR concept rely on numerical simulations making use of the MCNP neutron transport code coupled with a code for materials evolution which resolves the Bateman's equations giving the population of each nucleus inside each part of the reactor at each moment. Because of MSR's fundamental characteristics compared to classical solid-fuelled reactors, the classical Bateman ...

286

Reduction in blood pressure with a low sodium, high potassium, high magnesium salt in older subjects with mild to moderate hypertension.  

UK PubMed Central (United Kingdom)

OBJECTIVE--To examine the effect of a reduced sodium and increased potassium and magnesium intake on blood pressure. DESIGN--Randomised double blind placebo controlled trial. SETTING--General population...Full Text Available

1994-08-13

287

Proline Betaine Accumulation and Metabolism in Alfalfa Plants under Sodium Chloride Stress. Exploring Its Compartmentalization in Nodules1  

UK PubMed Central (United Kingdom)

The osmoprotectant Pro betaine is the main betaine identified in alfalfa (Medicago sativa). We have investigated the long-term responses of nodulated alfalfa plants to salt stress,...Full Text Available

2004-07-01

288

Preparation of internally labelled rat pituitary somatotropin (growth hormone).  

UK PubMed Central (United Kingdom)

Rat somatotropin (growth hormone) was labelled biosynthetically by incubating anterior pituitary lobes with radioactive amino acids for 24 h in a simple buffered salts medium containing glucose. The...Full Text Available

1978-03-01

289

Mild salinity stimulates a stress-induced morphogenic response in Arabidopsis thaliana roots  

UK PubMed Central (United Kingdom)

Plant roots exhibit remarkable developmental plasticity in response to local soil conditions. It is shown here that mild salt stress stimulates a stress-induced morphogenic response (SIMR) in Arabidopsis...Full Text Available

2010-01-01

290

Mean distance of closest approach of alkaline-earth metals ions in aqueous solutions: Experimental and theoretical calculations  

British Library Electronic Table of Contents (United Kingdom)

The estimation of numerical values of the mean distance of closest approach of ions, a, of alkaline-earth metal ion salts in aqueous solutions, determined from activity coefficients, as well as from different theoretical approaches, is presented and discussed.

2010-01-01

291

Ionic conductivity enhancement for lithium solid electrolyte; Lithium ion dodensei kotai denkaishitsu no dodensei kojo kiko no kaimei  

Energy Technology Data Exchange (ETDEWEB)

For the development of high ionic conductive solid electrolyte, LiTi2(PO4)3 (LTP), one of the promising inorganic solid electrolyte, was synthesized to investigate an effect of additional lithium salt on the ion conductivity. Lithium salt added LTP composite electrolyte sintered at 900{degree}C exhibited highest conductivity, which was two order magnitude higher than pure LTP. Effects of lithium salt addition are as follows. Conductivity of the composite electrolyte provided larger sintering temperature dependence than the pure LTP. From X-ray diffraction analysis, structures and compositions were resemble between two composite electrolytes. Byproducts except LTP provided rather low conductivity. It was suggested that melted constitution in the composite can affect the sintering improvement by the additional lithium salt at temperatures over 800 {degree}C. From the observation of ruptured surface of ...

1996-08-01

292

Intestinal accumulation of lead salts and milk lead by suckling rats  

International Nuclear Information System (INIS)

Absorption of lead is known to be enhanced during infancy. In this study, the sites of intestinal accumulation of Pb by suckling rats have been determined under various conditions using "2"0"3Pb as a tracer. When "2"0"3Pb was administered intragastrically (IG) as a soluble salt, accumulation occurred primarily in the duodenum, regardless of dose and vehicle. In contrast, when rat pups suckled from a dam which had received "2"0"3Pb, the only region of the small intestine showing accumulation of radioactivity was the ileum. To confirm that these differences were not related to the route of administration, rat milk was labeled with "2"0"3Pb and was then used for IG administration. Once again, accumulation (4 hr post-administration) was confined to the ileum. When the dose was increased 10-fold, milk Pb displayed some accumulation in duodenal tissue, but very much less than that of soluble Pb at the same time and dosage. At 20 hr postadministration, there was ...

293

Fissile solubility and monosodium titanate loading tests  

Energy Technology Data Exchange (ETDEWEB)

The solubilities of plutonium and uranium have been determined for alkaline salt solutions having compositions which bound those which will be processed in the In-Tank Precipitation (ITP) process. Loadings of plutonium and uranium onto monosodium titanate (MST) have been determined at temperatures bounding those expected to occur during ITP and using a salt solution which was determined to have the maximum solubility for uranium and plutonium. Fissile loadings increase with decreasing amounts of MST in contact with the salt solutions saturated in plutonium and uranium. At MST concentrations bounding those which are planned for the ITP process, expressions for the maximum loadings (wt %) are determined to be 0.29 - 0.20x[MST] for plutonium and 1.8 - 0.29x[MST] for uranium, where [MST] is the concentration of MST in grams/liter. These expressions are valid over the range of MST concentrations from 0.05 to 0.51 g/L and ...

1993-02-12

294

Evaluation of a New Chromogenic Medium, MRSA Select, for Detection of Methicillin-Resistant Staphylococcus aureus?  

UK PubMed Central (United Kingdom)

We compared MRSA Select to mannitol-salt agar with 8 μg/ml cefoxitin for the detection of methicillin-resistant Staphylococcus aureus (MRSA) from 6,199 clinical...Full Text Available

2006-12-01

295

Efficacy of standard glucose-based and reduced-osmolarity maltodextrin-based oral rehydration solutions: effect of sugar malabsorption.  

UK PubMed Central (United Kingdom)

Previously we reported that standard oral rehydration salts (ORS) solution is not as effective as a reduced-osmolarity glucose-based ORS for the treatment of children with acute noncholera diarrhoea:...Full Text Available

1996-01-01

296

Effects of NaCl on Proline Synthesis and Utilization in Excised Barley Leaves 1  

UK PubMed Central (United Kingdom)

Proline accumulation in NaCl-treated excised barley (Hordeum vulgare var Larker) leaves was studied. Leaves were treated by placing the cut end in NaCl solutions and allowing the salt...Full Text Available

1983-07-01

297

Effect of Anionic Salt and Highly Fermentable Carbohydrate Supplementations on Urine pH and on Experimentally Induced Hypocalcaemia in Cows  

UK PubMed Central (United Kingdom)

The objective of this experiment was to determine the effect of dietary grain on calcium homeostasis. Six rumen-fistulated dairy cows with 3 or more previous lactations and no history of parturient...Full Text Available

2004-01-01

298

Capture of genomic DNA on glass microscope slides  

UK PubMed Central (United Kingdom)

It is well known that DNA strands bind to silica surfaces in the presence of high concentrations of chaotropic salts. We developed simple methods to evaluate binding and recovery of DNA on flat...Full Text Available

2007-06-15

299

CO-DEVELOPMENT OF WETLANDS SOILS AND BENTHIC INVERTEBRATE COMMUNITIES FOLLOWING SALT MARSH CREATION. (R826111)  

Science.gov (United States)

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

300

Breakdowns of high-voltage transmission lines due to sea-salt deposits on insulators  

Energy Technology Data Exchange (ETDEWEB)

Until 1990, in Tuscany, salt pollution of anti-salt insulators installed on high-tension transmission lines had led to rare breakdowns. On the contrary, in the last months of 1990, in most of Tuscany, following a strong libeccio wind coming from the Tyrrhenian Sea, and due to a long period of drought, salt deposits accumulated on the insulators of the high-voltage transmission lines (380 kV, 220 kV and 132 kV). This phenomenon not only took place in the coastal areas near Livorno, Pisa and Grosseto, but also in areas far away from the sea such as Florence, Prato, Arezzo and Siena. Following this, several high-tension lines, and whole sections of 380 kV electric stations went out of order, damaging the stations' equipment, insulators on the lines, and in particular porcelain insulators. The maintenance operations that were immediately undertaken consisted in washing operations, first focussed on stations, and then ...

1992-03-01

301

Breakdowns of high-voltage transmission lines due to sea-salt deposits on insulators  

International Nuclear Information System (INIS)

Until 1990, in Tuscany, salt pollution of anti-salt insulators installed on high-tension transmission lines had led to rare breakdowns. On the contrary, in the last months of 1990, in most of Tuscany, following a strong libeccio wind coming from the Tyrrhenian Sea, and due to a long period of drought, salt deposits accumulated on the insulators of the high-voltage transmission lines (380 kV, 220 kV and 132 kV). This phenomenon not only took place in the coastal areas near Livorno, Pisa and Grosseto, but also in areas far away from the sea such as Florence, Prato, Arezzo and Siena. Following this, several high-tension lines, and whole sections of 380 kV electric stations went out of order, damaging the stations' equipment, insulators on the lines, and in particular porcelain insulators. The maintenance operations that were immediately undertaken consisted in washing operations, first focussed on stations, and then on lines. ...

1992-01-01

302

Adverse Effect of Ammonium Salts on the Antibacterial Activity of Paraformaldehyde Solutions  

UK PubMed Central (United Kingdom)

The antibacterial activity of aqueous solutions of paraformaldehyde in concentrations from 0.1 to 0.4% (w/v) is bacteriostatic rather than bactericidal in the presence or absence of ammonium chloride....Full Text Available

1963-07-01

303

A rationale for stabilization of oxygen-labile enzymes: application to a clostridial hydrogenase.  

UK PubMed Central (United Kingdom)

A general procedure for stabilization of O2-labile enzymes exploiting "salting out" of oxygen from the microenvironment in the molecular layers immediately adjacent to charged surfaces of polyionic...Full Text Available

1978-08-01

304

46 CFR 160.171-17 - Approval testing for adult size immersion suit.  

Science.gov (United States)

...visible damage. (k) Corrosion resistance. Each metal part of a...evidence of salt-spray corrosion resistance equal to or greater than...sample of test metal must show corrosion resistance equal to or better than...

2010-10-01

305

Zonal, provincial, lithological, and geomorphic features of soil salinization in the Southern federal okrug of Russia  

British Library Electronic Table of Contents (United Kingdom)

The relationships between soil salinization and the zonal and provincial bioclimatic conditions, the lithological composition of the sediments, and the geomorphic features of the territory have been analyzed for the Southern federal okrug of Russia. It is shown that the lithological and geomorphic conditions (relief, salinity of parent materials, degree of drainage, and the depth of saline groundwater) play an important role in the distribution of salt-affected soils against the background of the more general regularities specified by the climate. The participation of salt-affected soils in the soil cover of the Southern federal okrug increases in the eastward direction from the forest-steppe zone to the semidesert zone in agreement with an increase in the aridity and continentality of the...

2011-01-01

306

Thermodynamics of potassium diclofenac salt aqueous solutions at various temperatures  

British Library Electronic Table of Contents (United Kingdom)

Solution and dilution enthalpies of aqueous solutions of potassium diclofenac salt (K_DC) were measured by an isoperibolic calorimeter at 298.15 and 318.5?K. Heat capacities of the solutions with concentrations 0.002?0.09?mol?kg?1 were obtained at the temperature interval of 288.15?318.15?K using a scanning adiabatic microcalorimeter. The virial coefficients were derived from Pitzer?s model, and the excess thermodynamic functions of both the solvent and the solute of the solution were calculated. The concentration and temperature dependencies of thermodynamic characteristics of the solution were analyzed and discussed.

2011-01-01

307

Preparation of poly (aryl ether ketones) in the presence of an alkali, alkaline earth of lanthanide metal salt  

Energy Technology Data Exchange (ETDEWEB)

This patent describes a process for preparing poly(aryl ether ketones) by nucleophilic displacement polymerization in the presence of at least one alkali metal base selected from potassium, rubidium or cesium, and fluoride ions, which comprises adding to the polymerization: (a) an effective amount of at least one metal salt selected from lithium, sodium, alkaline earth or lanthanide chloride, bromide, iodide, sulfate, alkyl or aryl carboxylate, cyanide, borate or phosphate to slow or stop advancement of molecular weight and (b) an end-capping agent.

1988-09-27

308

Polythermal study of the M(ClO_4)_2-H_2O systems, where M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+  

International Nuclear Information System (INIS)

Crystallization points of aqueous solution of the systems M(ClO_4)_2-H_2O (M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+), depending on the salt concentration, were identified by visual-polythermal method. Relying on model notions on the structure of the electrolyte solutions, specific features of strontium perchlorate solubility polytherm and concentration dependence of the relative dynamic viscosity of the salt aqueous solutions are discussed

2005-03-01

309

Development of detection methods for irradiated foods; development of immunological identification of irradiated foods  

Energy Technology Data Exchange (ETDEWEB)

Enzyme-linked Immunosorbent assay systems for the identification of irradiated egg, pork and chicken was developed. Eggs were irradiated in their shells to 0.5{approx}7kGy. Pork was irradiated to 0.5{approx}3kGy and chicken irradiated to 0.5kGy{approx}5kGy. The most sensitive proteins to irradiation were screened by SDS-PAGE and purified. Ovalbumin from egg, salt soluble protein(p) from pork, and salt soluble protein(c) from chicken showed the most sensitivity to irradiation. To investigate for a practical use in identifying of irradiated egg, pork and chicken, competitive ELISA was performed. The binding activity of ovalbumin to anti-ovalbumin IgG was reduced in a dose-dependent manner by irradiating up to 7kGy, and considerably lowered after irradiating at 7kGy. The concentration of 50% inhibition of ovalbumin to IgG was increased to 1.5(0.5kGy){approx}3.7(7kGy) times in an dose-dependent relationship. The binding activity of ...

2002-04-01

310

Corrosion and protection of magnesium alloy AZ31D by a new conversion coating  

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

2003-07-01

311

Slow strain-rate testing of Alloy 800 in molten-nitrate salts  

Energy Technology Data Exchange (ETDEWEB)

An experimental technique has been developed to examine the interaction between deformation and the exposure of certain high temperature structural alloys to oxidizing molten salt environments. The experimental program involved performing a series of long-term tensile tests over a wide range of strain rates. Fracture strain reduction in area and ultimate strength (UTS) were monitored as parameters indicative of an alloy's susceptibility to environmental degradation. For Incoloy Alloy 800 tested at 600/sup 0/C in the salt medium and at initial strain rates between 2 x 10/sup -7/ sec/sup -1/ and 1 x 10/sup -5/ sec/sup -/1 no appreciable loss of ductility, as measured by reduction in area, was observed relative to control specimens tested in air at the same temperature and strain rates. Similarly, fracture strain and UTS were essentially unaffected by exposure to the oxidizing environment. The structure of the oxide film formed by contact ...

1982-01-01

312

Quaternary faults near the proposed Eagle Flat low-level radioactive waste repository, Trans-Pecos Texas  

Science.gov (United States)

The Eagle Flat basin, an intermontane basin in Trans-Pecos Texas, is being considered as a possible site for the Texas repository of low-level radioactive wastes. Intermontane basins and associated normal faults formed in response to Basin and Range tectonism that began about 24 Ma ago. The most active late Tertiary and Quaternary faults occur within the Hueco Bolson (HB) and the Salt Basin/Salt Flat/Lobo Valley, west and east, respectively, of the proposed repository. Several faults of the southeast HB which are within 50 km of the site, displace middle Pleistocene deposits 10 to 24 m. The most recent surface rupture in the southeast HB probably occurred on the Amargosa fault during the Holocene. Upper Pleistocene deposits are offset 2.5 to 4.5 m, and middle Pleistocene deposits are displaced 24 m. Fault scarps within 50 km east of the proposed repository are associated with faults bounding the Salt ...

1992-01-01

313

Investigation of amine amino acid salts for carbon dioxide absorption  

Energy Technology Data Exchange (ETDEWEB)

The carbon dioxide capture potential of amine amino acid salts (AAAS), formed by mixing equinormal amounts of amino acids; e.g. glycine. B-alanine and sarcosine, with an organic base; 3-(methylamino)propylamine (MAPA), was assessed by comparison with monoethanolamine (MEA), and with amino acid salt (AAS) from amino acid neutralized with an inorganic base; potassium hydroxide (KOH). Carbon dioxide absorption and desorption experiments were carried out on the solvent systems at 40{sup o}C and 80{sup o}C respectively. Experimental results showed that amine amino acid salts have similar CO{sub 2} absorption properties to MEA of the same concentration. They also showed good signs of stability during the experiments. Amino acid salt from an inorganic base, KOH, showed lower performance in CO{sub 2} absorption than the amine amino acid salts (AAAS) mainly due to a lower equilibrium ...

2010-09-15

314

Interaction between high levels of applied heavy metals and indigenous soil manganese  

Energy Technology Data Exchange (ETDEWEB)

The importance of indigenous soil Mn level on plant Mn uptake from metal salt or sewage sludge amended soils was investigated. Twelve soil materials, six surface and six subsurface, were amended with either varying rates of a composite of Cd, Cu, Ni, and Zn sulfate salts, equivalent to the total of these metals present in a digested sewage sludge (Washington, DC) at rates of 0 to 896 dry metric tons/ha or with the sludge itself, at 224 dry metric tons/ha. Corn (Zea mays L.) was grown in the greenhouse for 30 days, 1 year after amendment application. Two pH levels of about 5.5 and 6.5 were maintained during the experiment on the metal salt amended soil materials. Plant tissue Mn levels increased with the application of Cd, Cu, Ni, and Zn (in combination) as metal salts or as sewage sludge over the range of soil materials used. The amount of increase with a given increase in applied metals was greater for ...

1981-01-01

315

Safe Water in an Emergency  

Medline Plus

English - Safe Water in an Emergency Click to Stop Video Click to Start Video To Listen to ...

316

Vulnerability Analysis of Physical Protection System at Wolsung Nuclear Power Plant  

Energy Technology Data Exchange (ETDEWEB)

The 9/11 event in the U.S.A has increased international terror possibilities against nuclear facilities including nuclear power plants(NPPs). It is necessary to assess the performance of an existing physical protection system(PPS) at nuclear facilities based on such malevolent acts. A PPS is a complex configuration of detection, delay, and response elements. Several methods are available to analyze a PPS and evaluate its effectiveness. Sandia National Laboratory(SNL) in the USA was developed a System Analysis of Vulnerability to Intrusion (SAVI) computer code for this purpose. It is powerful software for evaluating the effectiveness of PPS against outsider threats. This study presents the performance assessment of the PPS at Wolsung NPP using SAVI code. First, the site-specific Adversary Sequence Diagrams(ASDs) of the PPS is constructed. It helps to understand the functions of the existing PPS composed of physical areas and Protection Elements(PEs) at Wolsung NPP. ...

2006-07-01

317

Vulnerability Analysis of Physical Protection System at Wolsung Nuclear Power Plant  

International Nuclear Information System (INIS)

The 9/11 event in the U.S.A has increased international terror possibilities against nuclear facilities including nuclear power plants(NPPs). It is necessary to assess the performance of an existing physical protection system(PPS) at nuclear facilities based on such malevolent acts. A PPS is a complex configuration of detection, delay, and response elements. Several methods are available to analyze a PPS and evaluate its effectiveness. Sandia National Laboratory(SNL) in the USA was developed a System Analysis of Vulnerability to Intrusion (SAVI) computer code for this purpose. It is powerful software for evaluating the effectiveness of PPS against outsider threats. This study presents the performance assessment of the PPS at Wolsung NPP using SAVI code. First, the site-specific Adversary Sequence Diagrams(ASDs) of the PPS is constructed. It helps to understand the functions of the existing PPS composed of physical areas and Protection Elements(PEs) at Wolsung NPP. ...

2006-05-25

318

Strontium isotope ratios and the origin of anorthosites  

Energy Technology Data Exchange (ETDEWEB)

Anorthosites are rocks consisting almost completely of calcic plagioclase, usually from andesine to labradorite. They are not widespread, and until recently were of no economic interest. However, with the advance of the new global tectonics, which has excited considerable interest in the structure and composition of upper-mantle rocks, interest in the anorthosites has grown. This has particularly been the case since the discovery of anorthosites on the moon, where they appear to be more widespread than on the earth. Data have recently been obtained on the strontium isotope compositions of anorthosite intrusions in the Dzhugdzhur-Stanovoy zone and in the rocks surrounding them, which have revealed some unexpected features. The paper describes the geological features of anorthosites, initial concepts on strontium isotope geochemistry, strontium isotope compositions of this region, and discusses some genetic consequences from the isotope data. Although the data of ...

1986-01-01

319

Pore size distribution, strength, and microstructure of portland cement paste containing metal hydroxide waste  

Energy Technology Data Exchange (ETDEWEB)

Stabilization/solidification of hazardous wastes is used to convert hazardous metal hydroxide waste sludge into a solid mass with better handling properties. This study investigated the pore size development of ordinary portland cement pastes containing metal hydroxide waste sludge and rice husk ash using mercury intrusion porosimetry. The effects of acre and the addition of rice husk ash on pore size development and strength were studied. It was found that the pore structures of mixes changed significantly with curing acre. The pore size shifted from 1,204 to 324 {angstrom} for 3-day old cement paste, and from 956 to 263 {angstrom} for a 7-day old sample. A reduction in pore size distribution for different curing ages was also observed in the other mixtures. From this limited study, no conclusion could be made as to any correlation between strength development and porosity. 10 refs., 6 figs., 3 tabs.

1996-12-31

320

Performance Assessment of Physical Protection System at Wolsong Nuclear Power Plant using SAVI code  

Energy Technology Data Exchange (ETDEWEB)

The 9/11 event in the U.S.A has increased international terror possibilities against nuclear facilities including nuclear power plants(NPPs). It is necessary to assess the performance of existing physical protection system(PPS) at nuclear facilities based on such malevolent acts. A PPS is a complex configuration of detection, delay, and response elements. Several techniques are available to analyze a PPS and evaluate its effectiveness. Sandia National Laboratory(SNL) in the USA was developed a System Analysis of Vulnerability to Intrusion (SAVI) computer code for this purpose. It is powerful software for evaluating the effectiveness of PPS against outsider threats. This study presents the performance assessment of the PPS at Wolsong NPP using SAVI code. The first is that the SAVI constructs the site-specific Adversary Sequence Diagram (ASD) of the PPS. This provides a methods of graphically representing the PPS composed of physical areas and Protection ...

2005-07-01

321

Oklo. A review and critical evaluation of literature  

Energy Technology Data Exchange (ETDEWEB)

The Oklo natural fossil fission reactors in Gabon, Equatorial Africa, have been studied as a natural analogue for spent nuclear fuel in a geological environment. For these studies, it is important to know what has happened to these reactors since they formed. This review is focussed on existing geological and geochronological information concerning the Oklo reactors and the surrounding ore. A sequence of geological and geochemical events in the Oklo area, as described in the literature, is given. The data and the studies behind this established geochronology are discussed and evaluated. Of the regional geology, special attention is given to the dating of the Francevillian sediments, and the intrusion of a dolerite dyke swarm. The processes that led to the mineralisation at Oklo, the subsequent formation of the nuclear reactors and later migration of fission products are described. Further discussion concerns the studies of the dolerite dyke swarm, since this ...

2000-10-01

322

ORNL results for Test Case 1 of the International Atomic Energy Agency`s research program on the safety assessment of Near-Surface Radioactive Waste Disposal Facilities  

Energy Technology Data Exchange (ETDEWEB)

The International Atomic Energy Agency (IAEA) started the Coordinated Research Program entitled ```The Safety Assessment of Near-Surface Radioactive Waste Disposal Facilities.`` The program is aimed at improving the confidence in the modeling results for safety assessments of waste disposal facilities. The program has been given the acronym NSARS (Near-Surface Radioactive Waste Disposal Safety Assessment Reliability Study) for ease of reference. The purpose of this report is to present the ORNL modeling results for the first test case (i.e., Test Case 1) of the IAEA NSARS program. Test Case 1 is based on near-surface disposal of radionuclides that are subsequently leached to a saturated-sand aquifer. Exposure to radionuclides results from use of a well screened in the aquifer and from intrusion into the repository. Two repository concepts were defined in Test Case 1: a simple earth trench and an engineered vault.

1993-07-01

323

Mixed waste landfill corrective measures study final report Sandia National Laboratories, Albuquerque, New Mexico.  

Energy Technology Data Exchange (ETDEWEB)

The Mixed Waste Landfill occupies 2.6 acres in the north-central portion of Technical Area 3 at Sandia National Laboratories, Albuquerque, New Mexico. The landfill accepted low-level radioactive and mixed waste from March 1959 to December 1988. This report represents the Corrective Measures Study that has been conducted for the Mixed Waste Landfill. The purpose of the study was to identify, develop, and evaluate corrective measures alternatives and recommend the corrective measure(s) to be taken at the site. Based upon detailed evaluation and risk assessment using guidance provided by the U.S. Environmental Protection Agency and the New Mexico Environment Department, the U.S. Department of Energy and Sandia National Laboratories recommend that a vegetative soil cover be deployed as the preferred corrective measure for the Mixed Waste Landfill. The cover would be of sufficient thickness to store precipitation, minimize infiltration and deep percolation, support a healthy vegetative ...

2004-03-01

324

In situ isotopic analyses of U and Pb in zircon by remotely operated SHRIMP II, and Hf by LA-ICP-MS: an example of dating and genetic evolution of zircon by 176Hf/177Hf from the Ita Quarry in the Atuba Complex, SE, Brazil  

International Nuclear Information System (INIS)

Remotely-operated SHRIMP dating of zircon is an interesting alternative for dating of zircon crystals. Although it does not represent any technical progress of the geochronological method using the U-Pb system in zircon it is a very useful and cheap facility. The procedure was first used for mass spectrometric analyses involving two international laboratories in Sao Paulo, Brazil and Beijing, China. It was applied to samples of three gneiss-migmatitic rocks from the Ita quarry in the Atuba Complex (located between the Luis Alves and the Apiai Domain) to test previous controversial hypotheses about its evolution. The presence of important archaean and paleo proterozoic components in the complex is confirmed by analyses of zircon found in probably neo proterozoic leucosomes. Diorite intrusion also occurred during the neo proterozoic, associated with the 0.6Ga continental collisions involved in the assembly of Gondwana. The determination of Hf isotope ratios by ...

2009-10-01

325

Hierarchical Kohonenen net for anomaly detection in network security.  

Science.gov (United States)

A novel multilevel hierarchical Kohonen Net (K-Map) for an intrusion detection system is presented. Each level of the hierarchical map is modeled as a simple winner-take-all K-Map. One significant advantage of this multilevel hierarchical K-Map is its computational efficiency. Unlike other statistical anomaly detection methods such as nearest neighbor approach, K-means clustering or probabilistic analysis that employ distance computation in the feature space to identify the outliers, our approach does not involve costly point-to-point computation in organizing the data into clusters. Another advantage is the reduced network size. We use the classification capability of the K-Map on selected dimensions of data set in detecting anomalies. Randomly selected subsets that contain both attacks and normal records from the KDD Cup 1999 benchmark data are used to train the hierarchical net. We use a confidence measure to label the clusters. Then we use the test set from the ...

2005-04-01

326

Collection and analysis of particulate from the DIII-D Tokamak  

International Nuclear Information System (INIS)

Particulate (i.e. tokamak dust) has been collected from the DIII-D tokamak located at General Atomics in San Diego, CA, USA. Two methods were used to collect particulate with the goal of preserving the particle size distribution and physical characteristics of the particulate. Vacuum collection on substrates and adhesion removal with metallurgical replicating tape were chosen as non-intrusive sampling methods. Sampling was completed in four toroidal locations of the machine; the 0-90 area, the 90-180 area, the 180-270 area, and the 270-360 area. The 0 direction designates the north side of the DIII-D machine. Four tiles in each area were sampled; the first vertical tile above the floor on the centerpost, a floor tile next to the center post, a tile on the isolated ring, and the first tile up from the isolated ring on the divertor. In addition, samples were collected from underneath the floor tiles at the 275 and the 75 locations. The count median diameter of the ...

1998-09-01

327

Aerial gamma ray and magnetic survey: Idaho Project, Idaho Falls quadrangle, Idaho. Final report  

International Nuclear Information System (INIS)

The Idaho Falls quadrangle in southeastern Idaho lies at the juncture of the Snake River Plain, the Northern Rocky Mountains, and the Basin-Range Province. Quaternary basalts of the Snake River Plain occupy 70% of the quadrangle. The rest of the area is covered by uplifted Paleozoic, Mesozoic, and Cenozoic rocks of the Pre-Late Cenozoic Orogenic Complex. Magnetic data apparently show contributions from both shallow and deep sources. The apparent expression of intrusive and extrusive rocks of late Mesozoic and Cenozoic age tends to mask the underlying structural downtrap thought to exist under the Snake River Plain. The Idaho Falls quadrangle has been unproductive in terms of uranium mining. A single claim exists in the Sawtooth Mountains, but no information was found concerning its present status at the time of this study. A total of 169 anomalies are valid according to the criteria set forth in Volume I of this report. These anomalies are scattered throughout the ...

328

Acceptable requirement of decontamination factor for LLW disposal of PEACER pyro-processing wastes  

International Nuclear Information System (INIS)

A pyrochemical process has been introduced and utilized so that the transmutation of spent PWR fuel in PEACER can produce mainly low and intermediate level waste for near surface disposal. Major radioactive nuclides from PEACER pyro-processing are composed of TRU and LLFP. In this study, the requirement for the final waste from PEACER is evaluated based on the methodology for establishment of waste acceptance criteria. Also, sensitivity analysis for several input parameters is conducted in order to determine acceptable decontamination factor (DF) and LLFP removal efficiency and to find out input parameter that extremely have an effect on DF. As a result of the study, LLFP removal efficiency, especially Sr-90 and Tc-99, is proved to be a major nuclide which contributes to annual dose by human intrusion scenario rather than TRU DF. More than 98.5% of LLFP have to be removed to meet below dose constraint within the DF more than 5.0E+03. Besides, because of the ...

2007-09-09

329

Acceptable decontamination factor for near-surface disposal of PEACER wastes  

Energy Technology Data Exchange (ETDEWEB)

A pyrochemical process has been introduced and utilized so that the transmutation of spent PWR fuel in PEACER can produce mainly low and intermediate level waste for near surface disposal. Major radioactive nuclides from PEACER pyroprocessing are composed of TRU and LLFP. In this study, the requirement for the final waste from PEACER is evaluated based on the methodology for establishment of waste acceptance criteria. Also, sensitivity analysis for several input parameters is conducted in order to determine acceptable decontamination factor (DF) and LLFP removal efficiency and to find out input parameter that extremely have an effect on DF. As a result of the study, LLFP removal efficiency, especially Sr-90 and Tc-99, is proved to be a major nuclide which contributes to annual dose by human intrusion scenario rather than TRU DF. More than 98.5% of LLFP have to be removed to meet below dose constraint within the DF more than 5.0E + 03. Besides, because of the ...

2005-11-15

330

Acceptable decontamination factor for near-surface disposal of PEACER wastes  

International Nuclear Information System (INIS)

A pyrochemical process has been introduced and utilized so that the transmutation of spent PWR fuel in PEACER can produce mainly low and intermediate level waste for near surface disposal. Major radioactive nuclides from PEACER pyroprocessing are composed of TRU and LLFP. In this study, the requirement for the final waste from PEACER is evaluated based on the methodology for establishment of waste acceptance criteria. Also, sensitivity analysis for several input parameters is conducted in order to determine acceptable decontamination factor (DF) and LLFP removal efficiency and to find out input parameter that extremely have an effect on DF. As a result of the study, LLFP removal efficiency, especially Sr-90 and Tc-99, is proved to be a major nuclide which contributes to annual dose by human intrusion scenario rather than TRU DF. More than 98.5% of LLFP have to be removed to meet below dose constraint within the DF more than 5.0E + 03. Besides, because of the ...

2005-11-01

331

Water resources data for Minnesota, water year 1993. Volume 2. Upper Mississippi and Missouri River basins. Water-data report (Annual), 1 October 1992-30 September 1993  

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1993 water year for Minnesota consists of records of stage, discharge and water quality of streams; stage, contents, and water quality of lakes and reservoirs; and water levels and water quality in wells and springs. This volume contains discharge records for 58 gaging stations; stage and contents for 9 lakes and reservoirs; water quality 15 stream stations, 1 lakes station, 1 precipitation station, and water levels for 15 observation wells. Also included are 61 high-flow partial-record stations. Additional water data were collected at various sites, not part of the systematic data collection program and are pulished as miscellaneous measurements.

1994-07-01

332

Water resources data for Minnesota, water year 1991. Volume 2. Upper Mississippi and Missouri River Basins. Water-data report (Annual), 1 October 1990-30 September 1991  

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1991 water year for Minnesota consist of records of stage, discharge and water quality of streams; stage, contents, and water quality of lakes and reservoirs; and water levels and water quality in wells and springs. The volume contains discharge records for 60 gaging stations; stage and contents for 9 lakes and reservoirs; water quality for 18 stream stations, 1 lake station, 22 partial-record sites, 1 precipitation station, 108 wells; and water levels for 119 observation wells. Also included are 59 high-flow partial-record stations. Additional water data were collected at various sites, not part of the systematic data collection program and are published as miscellaneous measurements or low-flow investigations.

1992-09-01

333

National Water Plan draft  

International Nuclear Information System (INIS)

In the National Water Plan it is described which measures must be taken to keep the Netherlands safe and livable for future generations and to make use of the chances offered by water.

334

CDC Data & Statistics | Feature: Drowning Risks in Natural Water...  

Science.gov (United States)

swimmers in or around the water. Designate a responsible adult who can swim and knows CPR to watch swimmers in or around water. The supervisor should not be involved in any...

2011-09-24

335

Salt decontamination demonstration test results  

International Nuclear Information System (INIS)

The Salt Decontamination Demonstration confirmed that the precipitation process could be used for large-scale decontamination of radioactive waste sale solution. Although a number of refinements are necessary to safely process the long-term requirement of 5 million gallons of waste salt solution per year, there were no observations to suggest that any fundamentals of the process require re-evaluation. Major accomplishments were: (1) 518,000 gallons of decontaminated filtrate were produced from 427,000 gallons of waste salt solution from tank 24H. The demonstration goal was to produce a minimum of 200,000 gallons of decontaminated salt solution; (2) cesium activity in the filtrate was reduced by a factor of 43,000 below the cesium activity in the tank 24 solution. This decontamination factor (DF) exceeded the demonstration goal of a DF greater than 10,000; (3) average strontium-90 activity in the ...

336

New molten salt systems for high temperature molten salt batteries: Ternary and quaternary molten salt systems based on LiF-LiCl, LiF-LiBr, and LiCl-LiBr  

British Library Electronic Table of Contents (United Kingdom)

Using a new simulative technique developed by us, we systematically investigated new ternary or quaternary molten salt systems, which are based on LiF-LiCl, LiF-LiBr, and LiCl-LiBr binary systems, for use as electrolytes in thermal batteries, and evaluated their ionic conductivities and melting points experimentally. It was confirmed experimentally that LiF-LiBr-KF (melting point: 425^oC, ionic conductivity at 500^oC: 2.52Scm^-^1), LiCl-LiBr-KF (405^oC, 2.56Scm^-^1), LiCl-LiBr-NaF-KF (425^oC, 3.11Scm^-^1), LiCl-LiBr-NaCl-KCl (420^oC, 2.73Scm^-^1), and LiCl-LiBr-NaBr-KBr (420^oC, 2.76Scm^-^1) meet our targets for both melting point (350-430^oC) and ionic conductivity (2.0Scm^-^1 and higher at 500^oC). A single cell using the newly developed LiCl-LiBr-NaCl-KCl molten salt as an electrolyte w...

2011-01-01

337

Immobilization of chloride-rich radioactive wastes produced by pyrochemical operations  

Energy Technology Data Exchange (ETDEWEB)

A a result of its former role as a producer of nuclear weapons components, the Rocky Flats Environmental Technology Site (RFETS), Golden, Colorado accumulated a variety of plutonium-contaminated materials. When the level of contamination exceeded a predetermined level (the economic discard limit), the materials were classified as residues rather than waste and were stored for later recovery of the plutonium. Although large quantities of residues were processed, others, primarily those more difficult to process, remain in storage at the site. It is planned for the residues with lower concentrations of plutonium to be disposed of as wastes at an appropriate disposal facility, probably the Waste Isolation Pilot Plant (WIPP). Because the plutonium concentration is too high or because the physical or chemical form would be difficult to get into a form acceptable to WIPP, it may not be possible to dispose of a portion of the residues at WIPP. The pyrochemical salts are ...

1997-08-01

338

Formation of double hafnium sulfates in the systems HfO"2-H"2SO"4-Me"2SO"4-H"2O (Me-Na, K, Rb, Cs and NH"4)  

International Nuclear Information System (INIS)

Influence of alkali elements on formation, composition, solubility and region of stability of complex hafnium sulfates, separated in the HfO"2-H"2SO"4-Me"2SO"4-H"2O (Me-Na, K, Rb, Cs and NH"4 group) systems is studied. In all cases hafnium forms the complex sulfates of three types differing by basicity or ratio HfO"2:SO"3 1:1, 1:1.5, 1:2. Three basic and three medium sulfates are crystallized in the systems with sodium; with rubidium, cesium and ammonium - two basic and two medium sulfates and with potassium - two basic and one medium salts. Anhydrous salts do not form in the investigated systems. Potassium salt approximately 0.3% according to HfO"2 is characterized by minimum solubility from the salts of 2HfOSO"4x(1-3)Me"2SO"4x(4-6)xH"2O while solubility of the same salts with rubidium, cesium and sodium increases from (0.25-1.0); (0.5-1.5) till (1.0-5)% according to HfO"2 ...

1982-01-01

339

Use of the parmbsc0 force field and trajectory analysis to study the binding of netropsin to the DNA fragment (5'CCAATTGG)2 in the presence of excess NaCl salt in aqueous solution  

British Library Electronic Table of Contents (United Kingdom)

The parmbsc0 force field was applied to study in detail the binding of netropsin, at a salt concentration of 0.28M Na^+, to the minor groove of an 8-mer (5'CCAATTGG)2 DNA duplex forming a netropsin.DNA complex which previously has been characterized by X-ray crystallography, albeit with the use of closely related DNA duplexes. The X-ray structure revealed that the terminal guanidinium and amidinium groups of netropsin interact with the extreme ends of the palindromic AATT sequence of the receptor DNA. The parmbsc0 parameters of B-DNA and AMBER v9 parameters of netropsin generated a stable 6ns molecular dynamics (MD) trajectory for a 1:1 class I binding motif of this complex. Trajectory analysis for the salt and hydration effects on the binding of netropsin to the 8-mer DNA duplex revealed ...

2011-01-01

340

Steady-state Ab Initio Laser Theory: Generalizations and Analytic Results  

CERN Document Server

We improve the steady-state ab initio laser theory (SALT) of Tureci et al. by expressing its fundamental self-consistent equation in a basis set of threshold constant flux states that contains the exact threshold lasing mode. For cavities with non-uniform index and/or non-uniform gain, the new basis set allows the steady-state lasing properties to be computed with much greater efficiency. This formulation of the SALT can be solved in the single-pole approximation, which gives the intensities and thresholds, including the effects of nonlinear hole-burning interactions to all orders, with negligible computational effort. The approximation yields a number of analytic predictions, including a "gain-clamping" transition at which strong modal interactions suppress all higher modes. We show that the single-pole approximation agrees well with exact SALT calculations, particularly for high-Q cavities. Within this range of validity, ...

2010-01-01

341

Simulation study using 3-D wavefield modeling for oil and gas exploration; Sanjigen hadoba modeling wo mochiita sekiyu tanko no simulation study  

Energy Technology Data Exchange (ETDEWEB)

As the surroundings of objects of oil exploration grow more complicated, seismic survey methods have turned 3-dimensional and, in this report, several models are examined using the 3-dimensional simulation technology. The result obtained by the conventional wave tracking method is different from actual wavefields, and is unrealistic. The difference method among the fullwave modelling methods demands an exorbitantly long computation time and high cost. A pseudospectral method has been developed which is superior to the difference method, and has been put to practical use thanks to the advent of parallel computers. It is found that a 3-dimensional survey is mandatory in describing faults. After examining the SEG/EAGE Salt model, it is learned that the salt is well-developed and that 3-dimensional depth migration is required for sub-salt exploration. It is also found through simulation of the EAGE/S Overthrust model, which is ...

1997-05-27

342

Recovery of uranium from uranium and lanthanides in LiCl-KCl molten salt by electrowinning including Cd-Li anode  

Energy Technology Data Exchange (ETDEWEB)

A trans-uranium (TRU) fuel should be manufactured and loaded in transmutation systems in order to transmute the long-lived TRU nuclides into short-lived ones. However, since all of the TRU nuclides are not completely transmuted in one cycle lifetime in transmutation systems, the spent TRU fuel has to be treated to recover the long-lived radionuclides or fuel matrix materials. One concept to manufacture TRU fuel for transmutation is to recover uranium from TRU and molten salt. If this type of fuel is adopted for transmutation, uranium could also be an objective material to be recovered and recycled. Since electrowinning is a promising technology to be employed for the recovery of uranium from fuel materials, some experimental work of electrowinning using anode of Cd-Li alloy was carried out in this study. The basic salt chosen was a mixture of LiCl-KCl which has an eutectic point at 357 .deg. C.

2005-07-01

343

Recovery of uranium from uranium and lanthanides in LiCl-KCl molten salt by electrowinning including Cd-Li anode  

International Nuclear Information System (INIS)

A trans-uranium (TRU) fuel should be manufactured and loaded in transmutation systems in order to transmute the long-lived TRU nuclides into short-lived ones. However, since all of the TRU nuclides are not completely transmuted in one cycle lifetime in transmutation systems, the spent TRU fuel has to be treated to recover the long-lived radionuclides or fuel matrix materials. One concept to manufacture TRU fuel for transmutation is to recover uranium from TRU and molten salt. If this type of fuel is adopted for transmutation, uranium could also be an objective material to be recovered and recycled. Since electrowinning is a promising technology to be employed for the recovery of uranium from fuel materials, some experimental work of electrowinning using anode of Cd-Li alloy was carried out in this study. The basic salt chosen was a mixture of LiCl-KCl which has an eutectic point at 357 .deg. C

2005-05-26

344

Processing and characterization of polyethylene/Brazilian clay nanocomposites  

Energy Technology Data Exchange (ETDEWEB)

Nanocomposites containing polyethylene (PE) and montmorillonite clay organically modified (OMMT) with quaternary ammonium salts were obtained via direct melt intercalation. A montmorillonite sample from the Brazilian state of Paraiba was treated with four different types of quaternary ammonium salts. After the treatment, the powder was characterized by X-ray diffraction and scanning electron microscopy. The dispersion and morphologies of OMMT within PE were investigated by X-ray diffraction and transmission electron microscopy. The results revealed the formation of intercalated montmorillonite layers in the PE matrix. The thermal stability and flammability of the PE/montmorillonite clay nanocomposites were measured by thermogravimetry and horizontal burning tests for HB classification, Underwrites Laboratories (UL 94), respectively. It was shown that the samples do not degrade at the processing temperature. By adding only 3 wt.% ...

2007-02-15

345

New facility design and work method for the quantitative fit testing laboratory. Master's thesis  

Energy Technology Data Exchange (ETDEWEB)

The United States Air Force School of Aerospace Medicine (USAFSAM) tests the quantitative fit of masks which are worn by military personnel during nuclear, biological, and chemical warfare. Subjects are placed in a Dynatech-Frontier Fit Testing Chamber, salt air is fed into the chamber, and samples of air are drawn from the mask and the chamber. The ratio of salt air outside the mask to salt air inside the mask is called the quantitative fit factor. A motion-time study was conducted to evaluate the efficiency of the layout and work method presently used in the laboratory. A link analysis was done to determine equipment priorities, and the link data and design guidelines were used to develop three proposed laboratory designs. The proposals were evaluated by projecting the time and motion efficiency, and the energy expended working in each design. Also evaluated were the lengths of the equipment links for each proposal, and ...

1989-05-01

346

Influence of composite LiCl-KCl molten salt on microstructure and electrochemical performance of spinel Li4Ti5O12  

International Nuclear Information System (INIS)

A series of spinel Li4Ti5O12 samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li4Ti5O12. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li4Ti5O12 with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li4Ti5O12 with L = 1.5 has an initial discharge capacity of 169 mAh g-1 and an initial charge-discharge efficiency of 94% at 0.2 C rate, and achieves good ...

2008-12-30

347

Influence of composite LiCl-KCl molten salt on microstructure and electrochemical performance of spinel Li4Ti5O12  

British Library Electronic Table of Contents (United Kingdom)

A series of spinel Li4Ti5O12 samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li4Ti5O12. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li4Ti5O12 with L=1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized...

2008-01-01

348

Fluctuation of lithium isotopic ratios induced by salt concentrations in a liquid-liquid extraction system  

International Nuclear Information System (INIS)

Liquid-liquid extractive separation of lithium isotopes was carried out in order to investigate the fluctuation of separation factors (a) as a function of salt concentrations in an aqueous phase. Two equations for separation factor (a_o_b_s) as a function of the concentration were introduced; one for the diluted region, and another for the concentrated region. In the former solution where hydrated lithium ions are predominant, 1n a_o_b_s = Ac + B, and in the latter where ion-pairs with anions are predominant, 1n a_o_b_s = Dc + E(c - F)"1"/"3 + G. Some guidelines are derived from the salt-specific constants A, B, D, E, F and G. The heavier isotopes are inclined to be in the more hydrated state in the diluted solution, while the lighter isotopes tend to be in a less hydrated state. In the concentrated solution, heavier isotopes are more likely to be in ion-pair form. Ionic association occurs from the lower concentration in the order of LiI < ...

349

Effect of pH on the phase separation in the ternary aqueous system containing the hydrophilic ionic liquid 1-butyl-3-methylimidazolium bromide and the kosmotropic salt potassium citrate at T=298.15K  

British Library Electronic Table of Contents (United Kingdom)

The goal of this work is to study the effect of the aqueous medium pH on the two-phase equilibrium behaviour of the aqueous {1-butyl-3-methylimidazolium bromide ([C4mim]Br)+potassium citrate} system in order to obtain further information about the salting-out effect produced by the addition of a kosmotropic salt to an aqueous solution of a hydrophilic ionic liquid (IL). For this purpose the phase diagrams and the liquid-liquid equilibrium (LLE) data of the {[C4mim]Br+potassium citrate} aqueous two-phase system (ATPS) were determined experimentally at different pH values. Four medium pH values (5.00, 6.00, 7.00 and 8.00) were assayed at T=298.15K. The effect of pH on the ATPS-promoting capability of citrate anions in the aqueous [C4mim]Br solutions was explained based on the structural hydr...

2011-01-01

350

Development of pyro-separation technology based on molten salt electrolysis  

International Nuclear Information System (INIS)

In order to effectively recover uranium, rotation speed of solid cathode was examined, and effect of uranium concentration and current density on electrodeposition were confirmed. And the potentiostatic and galvanostatic electrorefining experiments were conducted. Element used in the experiments were Zr, Nd, La chlorides. The reduction potentials of chlorides metals on liquid Cd cathode were measured by cyclic voltammetry experiments. The electrowinning experiments were performed in order to recover small amounts of uranium in salt. Experimental set-up for the batch type reductive extraction experiments were developed and installed. On the base of experimental results of batch type, multi-stage extraction equipment was set-up, and optimum number of stage and recover yield were measured. In the oxidative extraction study is examine selective separation behavior of the rare earth metals from alloy composed of actinide and lanthanide metals to determine the effective ...

2010-10-01

351

Current and Future Costs for Parabolic Trough and Power Tower Systems in the US Market: Preprint  

Energy Technology Data Exchange (ETDEWEB)

NREL's Solar Advisor Model (SAM) is employed to estimate the current and future costs for parabolic trough and molten salt power towers in the US market. Future troughs are assumed to achieve higher field temperatures via the successful deployment of low melting-point, molten-salt heat transfer fluids by 2015-2020. Similarly, it is assumed that molten salt power towers are successfully deployed at 100MW scale over the same time period, increasing to 200MW by 2025. The levelized cost of electricity for both technologies is predicted to drop below 11 cents/kWh (assuming a 10% investment tax credit and other financial inputs outlined in the paper), making the technologies competitive in the marketplace as benchmarked by the California MPR. Both technologies can be deployed with large amounts of thermal energy storage, yielding capacity factors as high as 65% while maintaining an optimum LCOE.

2010-10-01

352

Crystalline and Liquid Crystalline Organic-Inorganic Hybrid Salts with Cation-Sensitized Hexanuclear Molybdenum Cluster Complex Anion Luminescence  

British Library Electronic Table of Contents (United Kingdom)

Abstract The salts [Cnmim]2[Mo6Cl14] (mim = methylimidazolium; n = 4, 6, 12, 16, 18) have been obtained by reaction of CnmimCl with MoCl2. Thermal analysis shows the melting point decreases with increasing alkyl chain length of the cation. The imidazolium chloromolybdates(II) with n = 6-18 decompose above 340 C; [C18mim]2[Mo6Cl14] is thermally stable up to 390 C. All compounds are insensititve to the constituents of the atmosphere. Of the higher melting salts [Cnmim]2[Mo6Cl14] (n = 4, 6), high-quality single crystals could be obtained. Single-crystal X-ray structural analyses clearly show that the cluster complex anion [Mo6Cl14]2- has an electron-precise octahedral {Mo6} cluster. For [C4mim]2[Mo6Cl14], two polymorphs differing in the cation alkyl-side-chain conformation were obtained. The ...

2011-01-01

353

Correlations for the yearly or seasonally optimum salt-gradient solar pond in Greece  

Energy Technology Data Exchange (ETDEWEB)

Simple correlations and corresponding nomographs are presented, which express the maximum useful heat received from salt-gradient solar ponds throughout the year or during a specified season of the year, and the corresponding optimum depth of the nonconvective zone in terms of the thickness of the upper convective zone and the temperature under which the maximum useful heat is received. The correlations are valid for the Athens (Greece) area or for regions with a similar climate, because solar radiation and ambient temperature values for Athens have been employed, obtained by a statistical process of hourly measurements over a period of about 20 years. For other climates, it is easy to develop similar correlations using the same methodology, Development of the proposed correlations is based on a method, which simulates the transient operation of the salt-gradient pond using finite-differences, and calculates the useful heat received hourly ...

1993-05-01

358

/sup 18/O isotope effect in carbon-13 nuclear magnetic resonance spectroscopy. Part 8. Oxygen exchange of 2,4,6-trimethylpyrylium cation  

Energy Technology Data Exchange (ETDEWEB)

The rate of the oxygen-exchange reaction in an aqueous solution of a heterocyclic oxygen compound, 2,4,6-trimethylpyrylium perchlorate, was quantitated. The /sup 18/O isotope effect in /sup 13/C NMR spectroscopy affords a direct, continuous, and relatively simple analysis of the reaction and was used to obtain data on the incorporation of /sup 18/O from solvent H/sub 2//sup 18/O into the pyrylium salt. Due to the low solubility of this salt in aqueous solutions, 2,4,6-trimethyl(2-/sup 13/C)pyrylium perchlorate and 2,4,6-trimethyl(2,6-/sup 13/C/sub 2/)pyrylium perchlorate were synthesized to facilitate the acquisition of the data on an NTC-200 spectrometer operating at 50.31 MHz. Upon incorporation of /sup 18/O into the pyrylium salt, the /sup 13/C NMR signal of the directly bonded carbon atom is shifted upfield 0.038 ppm. A /sup 13/C isotope effect is also detected in the doubly /sup 13/C-enriched pyrylium ...

1984-12-12

359

Turbidimetric determination of sulfite ion in inhibited ethylene glycol-water solutions  

Science.gov (United States)

Turbidimetric method for determining sulfite in inhibited ethylene glycol-water solutions

1970-01-01

360
361

REPORT NO. 853  

Science.gov (United States)

water and of the ethylene glycol-water solutions are shown as functions of temperature in figures 4 and 5, respectively. (data from reference 4). ...

362

Process for reducing the water content of coal containing bound water  

Energy Technology Data Exchange (ETDEWEB)

An improved process is disclosed for reducing the water content of coal containing bound water by releasing at least a portion of the bound water by maintaining the coal at a temperature from about 220/sup 0/ to about 500/sup 0/ F. in the presence of water at a pressure sufficient to maintain at least portion of the water in a liquid phase for a time sufficient to release at least a portion of the bound water wherein the improvement comprises contacting the coal during such treatment with an active material selected from the group consisting of carboxylic organic acids containing up to about 6 carbon atoms, phenol, phenolic acids and inorganic acids.

1983-08-23

363

Implementation of the national desalination and water purification technology roadmap : structuring and directing the development of water supply solutions.  

Energy Technology Data Exchange (ETDEWEB)

In the United States, economic growth increasingly requires that greater volumes of freshwater be made available for new users, yet supplies of freshwater are already allocated to existing users. Currently, water for new users is made available through re-allocation of xisting water supplies-for example, by cities purchasing agricultural water rights. Water may also be made available through conservation efforts and, in some locales, through the development of ''new'' water from non-traditional sources such as the oceans, deep aquifer rackish groundwater, and water reuse.

2006-06-01

364

Energy and Water Conservation  

Science.gov (United States)

Jet Propulsion Laboratory. California Institute of Technology. Pasadena, California. Energy and Water Conservation. Steve Rigdon. Facilities Energy Manager ...

365

Combustible Water Repellent Coating.  

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Water repellents, *Protective coatings, *Patents, Silica gel, Aluminum compounds, Binders ...

1973-07-24

366

Tetrazine explosives  

Energy Technology Data Exchange (ETDEWEB)

The synthesis and properties of various 1,2,4,5-tetrazine explosives and energetic materials are described. These are the nitrate and perchlorate salts of 3,6-diguanidino-1,2,4,5-tetrazine, the nitrate and perchlorate salts of 3,6-diguanidino-1,2,4,5-tetrazine-1,4-di-N-oxide, 3,6-bis(1H-1,2,3,4-tetrazol-5-ylamino)-1,2,4,5-tetrazine and its 1,4-di-N-oxide derivative, 3,3'-azobis(6-amino-1,2,4,5-tetrazine) and its oxidation products. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

2004-08-01

367

Status and progress in sludge washing: A pivotal pretreatment method  

Energy Technology Data Exchange (ETDEWEB)

Separation of the bulk soluble chemical salts from the insoluble metal hydroxides and radionuclides is central to the strategy of disposing Hanford tank waste. Sludge washing and caustic leaching have been selected as the primary methods for processing the 230 million L (61,000,000 gal) of Hanford tank waste. These processes are very similar to those selected for processing waste at the West Valley Site in New York and the Savannah River Site in South Carolina. The purpose of sludge washing is to dissolve and remove the soluble salts in the waste. Leaching of the insoluble solids with caustic will be used to dissolve aluminum hydroxide and chromium hydroxide, and convert insoluble bismuth phosphate to soluble phosphate. The waste will be separated into a high-level solids fraction and a liquid fraction that can be disposed of as low-level waste after cesium removal. The washing and leaching operations involve batchwise mixing, settling, and ...

1995-01-01

368

SAXS studies on added-salt species dependence of conformation of fully-charged poly(L-glutamate) in aqueous solutions  

Energy Technology Data Exchange (ETDEWEB)

The effect of counter-ion species on the local conformation of fully-charged poly(L-glutamate) in added-salt aqueous solutions were studied by small-angle X-ray scattering(SAXS). In the case of presence of monovalent counter-ion, the scattering behaviour could be explained by taking into consideration the excluded volume effect and intermolecular-interface interaction on the scattering function of wormlike chain. On the other hand, since SAXS profile of the solution in the presence of divalent counter-ion well fitted to the scattering function of dendrimer, it suggested that the conformation of polymer chain in such solution would be more compact conformation than that of presence of monovalent ion.

2010-10-01

369

Radioactive waste isolation in salt: peer review of Westinghouse Electric Corporation's report on reference conceptual designs for a repository waste package  

Energy Technology Data Exchange (ETDEWEB)

This report documents the findings of the peer panel constituted by Argonne National Laboratory to review Region A of Westinghouse Electric Corporation's report entitled Waste Package Reference Conceptual Designs for a Repository in Salt. The panel determined that the reviewed report does not provide reasonable assurance that US Nuclear Regulatory Commission (NRC) requirements for waste packages will be met by the proposed design. It also found that it is premature to call the design a ''reference design,'' or even a ''reference conceptual design.'' This review report provides guidance for the preparation of a more acceptable design document.

1985-10-01

370

Polymer-metal complex as gel electrolyte for quasi-solid-state dye-sensitized solar cells  

International Nuclear Information System (INIS)

A kind of polymer-metal complex gel electrolyte is successfully prepared and is used in dye-sensitized solar cells. Raman and X-ray photoelectron spectroscopy confirm the structure of this complex and is found that the metal ion reacts with nitrogen in the polymer. This novel electrolyte shows apparent diffusion coefficient of iodide of 8.37 x 10-7 cm2 s-1 and the energy conversion efficiency of 6.10% when the amount of ZnI2 is 0.04 M. By studying the dissociation active energy of the inorganic salt in electrolytes, we find that the metal salts can dissociate more easily after reacting with polymer and as a result can provide extra free iodide ion. The cell maintains ca. 93% of its initial efficiency after 20 d without further sealing, which shows good long-time stability.

2011-01-01

371

Mechanism of solubilization in detergent solutions  

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the solubilization of lauric acid, palmitic acid, stearic acid, and monopalmitin have been studied in detergent solutions as a function of concentration, temperature, and fluid flow. The detergents used were sodium dodecyl sulfate (an anionic surfactant), decyltrimethylammonium bromide (a cationic surfactant), sodium taurocholate (a trihydroxy bile salt), sodium taurodeoxycholate (a dihydroxy bile salt), and triton X-100 (a nonionic surfactant). At low temperature, solubilization can be described by a five-step mechanism is which micelle desorption and diffusion are rate controlling. At temperatures above the fatty acid penetration temperature, solubilization is governed by formation of a liquid crystalline phase at the fatty acid-detergent solution interface.

1981-11-01

372

Laboratory studies of the sensitivity of tropospheric ozone to the chemistry of sea salt aerosol. Final report, September 15, 1993--September 14, 1994  

Energy Technology Data Exchange (ETDEWEB)

Ozone plays a critical role in both the chemistry and radiation balance of the troposphere. Understanding the factors controlling tropospheric ozone levels is critical to our understanding of a variety of issues in global chemistry and climate change. Chlorine atoms have the potential to contribute significantly to the ozone balance in the free troposphere. They can react directly with ozone or alternately, with organics and may actually lead to the formation of ozone in the presence of sufficient NO. Reactions of alkali halides in sea salt particles are a potential source of atomic chlorine, hence reactions of these alkali halides, especially those producing precursors to atomic chlorine, are of great interest. Finally, the mechanisms, intermediates and products of the Cl-biogenic reactions are unknown; these could serve as unique markers of chlorine atom chemistry in the troposphere, and hence are important to define.

1994-11-15

373

Kinetics of spherulite formation and growth: Salt and protein concentration dependence on proteins b-lactoglobulin and insulin  

British Library Electronic Table of Contents (United Kingdom)

Proteins aggregated into spherulite structures of amyloid fibrils have been observed in patients with certain brain diseases such as Alzheimers and Parkinsons. The conditions under which these protein spherulites form and grow are not currently known. In order to illuminate the role of environmental factors on protein spherulites, this research aims to explore the kinetics and mechanisms of spherulite formation and growth, as monitored by optical microscopy, in a range of salt concentrations, and initial protein concentrations for two model proteins: bovine b-lactoglobulin and insulin. These two proteins are significantly different in their size and fibril growth rate, but both of these proteins have been shown previously to form amyloid fibrils and spherulites under low pH conditions. The...

2009-01-01

374

Ionic conduction in polyether-based lithium arylfluorosulfonimide ionic melt electrolytes  

Energy Technology Data Exchange (ETDEWEB)

We report synthesis, characterization and ion transport in polyether-based ionic melt electrolytes consisting of Li salts of low-basicity anions covalently attached to polyether oligomers. Purity of the materials was investigated by HPLC analysis and electrospray ionization mass spectrometry. The highest ionic conductivity of 7.1 x 10{sup -6} S/cm at 30 deg. C was obtained for the sample consisting of a lithium salt of an arylfluorosulfonimide anion attached to a polyether oligomer with an ethyleneoxide (EO) to lithium ratio of 12. The conductivity order of various ionic melts having different polyether chain lengths suggests that at higher EO:Li ratios the conductivity of the electrolytes at room temperature is determined in part by the amount of crystallization of the polyether portion of the ionic melt.

2009-10-01

375

Ionic conduction in polyether-based lithium arylfluorosulfonimide ionic melt electrolytes  

International Nuclear Information System (INIS)

We report synthesis, characterization and ion transport in polyether-based ionic melt electrolytes consisting of Li salts of low-basicity anions covalently attached to polyether oligomers. Purity of the materials was investigated by HPLC analysis and electrospray ionization mass spectrometry. The highest ionic conductivity of 7.1 x 10-6 S/cm at 30 deg. C was obtained for the sample consisting of a lithium salt of an arylfluorosulfonimide anion attached to a polyether oligomer with an ethyleneoxide (EO) to lithium ratio of 12. The conductivity order of various ionic melts having different polyether chain lengths suggests that at higher EO:Li ratios the conductivity of the electrolytes at room temperature is determined in part by the amount of crystallization of the polyether portion of the ionic melt.

2009-10-01

376

Impacts of membrane properties on reactive dye removal from dye/salt mixtures by asymmetric cellulose acetate and composite polyamide nanofiltration membranes  

British Library Electronic Table of Contents (United Kingdom)

This paper aims to study fundamentally the impacts of membrane properties on the reactive dye removal from dye/salt mixtures by nanofiltration membranes. To begin with, two types of nanofiltration membranes of similar pore size, namely asymmetric cellulose acetate membrane and thin-film composite polyamide membrane were fabricated, and their key physical, chemical and performance properties were characterized. After that, these resultant membranes were employed to perform dye removal experiments with aqueous solutions of reactive black 5 and NaCl under different operational parameters. The dye removal rate and steady permeate flux were determined and correlated with the measured membrane properties. It was found that there were significant differences between the dye removal performances o...

2010-01-01

377

DEGRADED TBP SOLVENT REGENERATION TECHNOLOGY USING BUTYLAMINE AS A SOLVENT WASHING TO REDUCE SOLID SALT WASTE  

Energy Technology Data Exchange (ETDEWEB)

Normal butylamine compounds are studied as salt-free wash reagents for degraded solvent used in PUREX process in spent fuel reprocessing. The solvent wash tests were carried out with two types of butylamine compounds, n-butylamine oxalate and n-butylamine bicarbonate, by counter-current mode using a small size mixer-settler composed of two 4-stage wash steps. Di-n-butyl phosphoric acid (HDBP), the main degradation product from TBP, was removed from real degraded solvent with decontamination factor of 2.5 {approx} 7.9. The study on electrolytic decomposition of butylamine compounds was also conducted for waste treatment.

2003-02-27

378

Converting hcp Mg-Al-Zn alloy into bcc Mg-Li-Al-Zn alloy by electrolytic deposition and diffusion of reduced lithium atoms in a molten salt electrolyte LiCl-KCl  

Energy Technology Data Exchange (ETDEWEB)

A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500 deg. C. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12 wt.% Li and only 0.264 wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.

2007-04-15

379

Converting hcp Mg-Al-Zn alloy into bcc Mg-Li-Al-Zn alloy by electrolytic deposition and diffusion of reduced lithium atoms in a molten salt electrolyte LiCl-KCl  

British Library Electronic Table of Contents (United Kingdom)

A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500degreeC. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12wt.% Li and only 0.264wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.

2007-01-01

380

Characteristics of lanthanides in pyrochemical systems observed by electrochemical and spectrophotometric measurements  

Energy Technology Data Exchange (ETDEWEB)

As research for the chemical properties of lanthanide molecules in the dry system, electrochemical and ultraviolet-visible optical measurements on the chloride molten salt system have been conducted at Research Reactor Institute, Kyoto University. The reduction behavior of Ln(III)-Ln(0) and Ln(II) are measured on La, Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, and Yb by the cyclic voltammetry. The molar absorption coefficients of the f-f transition are measured by the measurement of ultraviolet-visible absorption spectra on Pr, Nd, Ho and Gd. From the comparison of the optical data between wet and dry systems, the characteristics of photon absorption are discussed in the molten salt. (H. Katsuta)

2001-12-01

381

Aerial dispersal plasticity under different wind velocities in a salt marsh wolf spider  

British Library Electronic Table of Contents (United Kingdom)

Dispersal can be regarded as a process operating both between and within patches of suitable habitat. For uncontrolled dispersal processes, the risk of crossing the borders of the habitat patch and arriving in the unsuitable landscape matrix will increase with decreasing patch area, in particular when the distance between isolated habitat patches is larger than the species' average dispersal capacity. Ballooning dispersal in spiders can be considered as a passive dispersal process, in which dispersed distances depend on the prevalent wind velocity. We executed a reaction norm analysis to analyze how dispersal propensity of the salt marsh wolf spider Pardosa purbeckensis depended on population characteristics (patch size) and the environment (wind velocity). Dispersal propensity was affecte...

2007-01-01

382

/sup 109/Ag NMR spectra of aqueous silver ions coordinated with nitroxide radical. Silver-TANOL complex and TANOL as a doping agent  

Energy Technology Data Exchange (ETDEWEB)

The effects of TANOL radical have been examined on chemical shifts and relaxation rates of /sup 109/Ag NMR in aqueous solution of silver salts. The silver ion in aqueous solution is found to coordinate with TANOL radical. A small amount of TANOL is added as a doping agent(0.020M), since /sup 109/Ag signals are obtained for (1.0M) silver ion within 30 minutes. The /sup 109/Ag chemical shifts of silver salt in aqueous solutions were found within the range of 0 to -1000 ppm relative to that of 1.0M AgNo/sub 3/.

1982-09-01

383

Water chemistry and corrosion in water-steam circuits of nuclear power plants  

Energy Technology Data Exchange (ETDEWEB)

The water and steam circuits of steam generators in pressurized-water nuclear power plants are described together with the mechanism of denting, and the corrosion of spacer plates that leads to cracks in tubes by constriction. The different chemical specifications applicable to the water of the secondary circuit of the generators in normal operation and on first commissioning are listed. The results obtained and the measurements of chemical values taken in operation on the water in the secondary circuits of steam generators at Fessenheim and Bugey are presented.

1981-05-01

384

Water chemistry and corrosion in water-steam circuits of nuclear power plants  

International Nuclear Information System (INIS)

The water and steam circuits of steam generators in pressurized-water nuclear power plants are described together with the mechanism of denting, and the corrosion of spacer plates that leads to cracks in tubes by constriction. The different chemical specifications applicable to the water of the secondary circuit of the generators in normal operation and on first commissioning are listed. The results obtained and the measurements of chemical values taken in operation on the water in the secondary circuits of steam generators at Fessenheim and Bugey are presented.

385

Cooling facility for reactor container  

International Nuclear Information System (INIS)

Cooling water is sprayed on the outer surface of an upper portion of a container, and a pool is formed by the cooling water flowing down while cooling the container. Further, the cooling water stored in the cooling water pool is recycled by a pump for spraying the cooling water on the outer surface of the upper portion of the container. Sufficient amount of cooling water is supplied for spraying the cooling water to the outer surface of the upper portion of the container so that the outer surface of the container is free from drying and a liquid membrane is formed on the entire surface. The amount of the cooling water is made greater than that of the cooling water evaporated when the entire amount of the heat generate in the reactor core of the reactor is transferred to the cooling ...

1993-05-07

386

Water resources data for Texas, water year 1993. Volume 3. Colorado River basin, Lavaca River basin, Guadalupe River basin, Nueces River basin, Rio Grande basin, and intervening coastal basins. Water-data report (Annual), 1 October 1992-30 September 1993  

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1993 water year for Texas are presented in four volumes, and consist of records of stage, discharge, and water quality of streams and canals; and stage, contents, and water quality of lakes and reservoirs; and water levels and water quality of ground-water wells. Volume 3 contains records for water discharge at 134 gaging stations; stage only at 1 gaging stations; stage and contents at 13 lakes and reservoirs; water quality at 81 gaging stations; and data for 30 partial-record and 4 flood-hydrograph partial-record stations. Also included are lists of discontinued surface-water discharge or stage-only stations and discontinued surface-water-quality stations; crest-stage and flood-hydrograph partial-record stations, reconnaissance ...

1994-03-01

387

Thorium different-ligand complexes with morin as analytic form for extraction-photometric determination of thorium microamounts  

International Nuclear Information System (INIS)

Consideration is given to results of investigation into thorium complexing with morin (H_2Mor) in extraction systems containing different carboxylic acids as well as different salt background. The obtained data enabled to suggest the method of photometric determination of thorium in the form of Th(HMor)_2Benz_2 different-ligand complex (where Benz-anion of benzilic acid) with 0.25 #mu#g/ml detection limit.

1989-01-01

388

Synthesis and physicochemical properties of iron (2) perrhenates  

Energy Technology Data Exchange (ETDEWEB)

By dissolution of iron (2) carbonate in rhenium acid iron (2) perrhenate of the Fe(ReO/sub 4/)/sub 2/x4H/sub 2/O composition is obtained. By the method of thermal analysis the limits of tetra-, dihydrate and anhydrous iron (2) perrhenate stability are revealed. By means of X ray phase and IR spectroscopic analysis methods modification of structure in the process of synthesized salt dehydration is shown.

1983-01-01

389

Report of the Government Industrial Research Institute, Osaka, No. 388, February 1993. High lithium ion conductive solid electrolytes  

Energy Technology Data Exchange (ETDEWEB)

Research investigating applicability of lithium salts for solid electrolyte batteries was described. The studies included determinations of lithium ion conductivities in solid electrolyte systems based on Li4SiO4, LiTi2(PO4)3, and ceramic materials. Research on all solid state lithium cells utilizing TiS2 NiPS3 electrodes was also reported.

1993-01-01

390

Polymer electrolytes based on aromatic lithium sulfonyl-imide compounds; Electrolytes polymeres a base de sulfonylimidures de lithium aromatiques  

Energy Technology Data Exchange (ETDEWEB)

This paper presents ionic conductivity results obtained with polymer electrolytes and also with propylene carbonate solutions. The domain of electrochemical activity of this salt has been determined using cycle volt-amperometry in propylene carbonate. Preliminary experiments on the stability of the polymer electrolyte with respect to the lithium electrode have been carried out for a possible subsequent use in lithium batteries. (J.S.) 4 refs.

1996-12-31

391

Nuclear forensics in law enforcement applications  

International Nuclear Information System (INIS)

Over the past several years, the Livermore Forensic Science Center has conducted analyses of nuclear-related samples in conjunction with domestic and international criminal investigations. Law enforcement officials have sought conventional and nuclear-forensic analyses of questioned specimens that have typically consisted of miscellaneous metal species or actinide salts. The investigated activities have included nuclear smuggling and the proliferation of alleged fissionable materials, nonradioactive hoaxes such as 'Red Mercury', and the interdiction of illegal laboratories engaged in methamphetamine synthesis. (author)

1998-09-01

392

Novel procedure for an efficient and sparing cleaning procedure of turbines; Neues chemisches On-site-Reinigungsverfahren zur Wirkungsgraderhoehung von Dampfturbinen  

Energy Technology Data Exchange (ETDEWEB)

A new procedure for an efficient and sparing cleaning procedure of turbines was developed. The procedure uses cleaning and passivation chemicals that solve effectively and homogeneously salt and ferrous oxide coatings from turbines, avoiding attacks from corrosion, plugging and unbalances. In several high-pressure and condensation turbines the cleaning procedure has been already put into practice. (orig.)

2004-07-01

393

Mo"5 and W"5 complexing with tri-tret-butyl phenyl ether of 1.2-naphthoquinonediazide-(2)-5-sulfochloride  

International Nuclear Information System (INIS)

The complexing of paramagnetic salts of molybdenum and tungsten with tri-tert-butylphenyl ester of 1,2-naphthoquinone-diazide-(2)-5-sulfochloride is studied by PMR and EPR methods. From the changes of half-widths of lines in PMR spectra and analysis of g-factor in EPR spectra, the kinetic and thermodynamic parameters of the complexing are determined, and the composition of the complexes formed is established, and the schemes of their formation are suggested.

394

Metallic aggregate synthesis by radiolysis of simple or complex salt aqueous solutions. Study by electron microscope of aggregate grafting on carbon membranes  

International Nuclear Information System (INIS)

French ... Title Synthese d'agregats metalliques par radiolyse de solutions aqueuses de sels simples ou complexes. Etude par M. E. du greffage des agregats sur membranes de carbone.

1987-05-20

395

Highly efficient ion source for analysis of transuranium elements  

Energy Technology Data Exchange (ETDEWEB)

Results are described of the study of the analytical applicability of a highly efficient ion source developed for a mass spectrometer. Its ionizer is in the form of a partially closed cavity with a small aperture for leading out ions, heated to a high temperature. The new ion source increases the sensitivity of the apparatus in operations with transuranium elements by almost two orders of magnitude. It is possible to perform isotopic analyses with a high salt content in the sample, and to study the characteristics of nuclear fuel, even without chemical separation of the sample elements.

1987-01-01

396

Final report on low-cycle fatigue and creep-fatigue testing of salt-filled alloy 800 specimens  

Energy Technology Data Exchange (ETDEWEB)

Uniaxial low-cycle fatigue and creep-fatigue tests have been carried out on hollow alloy 800 specimens that were either filled with air or with a molten mixture of sodium nitrate, potassium nitrate and an oxidizer. Low-cycle fatigue tests were carried out at 1200/sup 0/F and 650/sup 0/F by cycling the strain continuously between equal mangitude of tensile and compressive values at a rate of 4 x 10/sup -3/sec/sup -1/ until failure. The creep-fatigue tests were carried out at 1200/sup 0/F. The loading cycle differed from that of low-cycle fatigue testing only in the imposition of a hold at the peak compressive strain in each cycle. Cracks always initiated on the inner surface of the hollow specimen, and therefore, corrosive effects on crack propagation and initiation were controlled by the environment within the specimen cavity. In common with tests carried out earlier on steam-filled alloy 800 specimens, at 1200/sup 0/F in the presence of molten salt the heat of ...

1982-05-01

397

Estimation of the mean distance of closest approach of some heavy metal ions in aqueous solutions: some experimental and theoretical calculations  

British Library Electronic Table of Contents (United Kingdom)

The estimation of numerical values of the mean distance of closest approach of ions, a, of heavy metal ion salts in aqueous solutions, determined from activity coefficients, as well as from different theoretical approaches, is presented and discussed.

2011-01-01

398

EFFECT OF DISSOLVED SOLIDS ON LIMESTONE FGD (FLUE GAS DESULFURIZATION) SCRUBBING CHEMISTRY  

Science.gov (United States)

The paper gives results of experiments in a 0.1 MW pilot plant to determine the effects of high concentrations of chloride ions and dissolved salts on flue gas desulfurization (FGD) scrubbing chemistry, both in the natural and forced oxidation modes of operation. (Note: The tight...

399

Determination of cesium and selenium in cultivated mushrooms using radionuclide X-ray fluorescence technique  

International Nuclear Information System (INIS)

Cesium and selenium intake of cultivated mushrooms (Agaricus bisporus), with these elements previously added to culture medium, has been examined from the viewpoint of health- and environmental protection. The process of measuring has been carried out by the radionuclide X-ray fluorescence technique. Treatments of the elementary substance with Se salt appears to influence the Se content of the mushrooms to a significant extent. Cs intake is of considerable importance, as this element is accumulated by mushrooms. (author)

2000-09-01

400

Densities and molar volumes of molten alkaline earth bromide - alkali bromide salt mixtures  

International Nuclear Information System (INIS)

The temperature and concentration dependence of the densities of binary CaBr_2-(Li, Na, K, Rb, Cs)Br, NaBr-(Sr, Ba)Br_2 and KBr-SrBr_2 mixtures have been measured using the method of hydrostatic weighing. With exception of the systems LiBr-CaBr_2 and NaBr-(Sr, Ba)Br_2 the calculated molar excess volumes are positiv in the investigated mixtures. (author).

1980-01-01

401

Catalysis over activated zeolites  

Science.gov (United States)

A process is provided for conducting organic compound conversion over a catalyst composition comprising a supported crystalline zeolite having a high initial silica-to-alumina mole ratio, said supported zeolite being prepared by compositing said crystalline zeolite with alumina, reacting the composite with a particular hydrogen fluoride solution in a specified way, drying the hydrogen fluoride reacted composite, treating the dried composite by hydrolysis, ammonolysis and/or by contact with an ammonium salt solution, and calcining the resulting material.

1985-02-19

402

Absorption of 308-nm excimer laser radiation by balanced salt solution, sodium hyaluronate, and human cadaver eyes  

Energy Technology Data Exchange (ETDEWEB)

Absorption of the excimer laser radiations of 193-nm argon fluorine and 308-nm xenon chloride in balanced salt solution, sodium hyaluronate, and human cadaver eyes was measured. The absorption of these materials as considerably different for the two wavelengths; we found that 308-nm light experienced much less absorption than the 193-nm light. The extinction coefficient (k) for 308 nm was k = 0.19/cm for balanced salt solution and k = 0.22/cm for sodium hyaluronate. In contrast to this, the extinction coefficient for 193 nm was k = 140/cm for balanced salt solution and k = 540/cm for sodium hyaluronate. Two 1-day-old human phakic cadaver eyes showed complete absorption with both wavelengths. Using aphakic eyes, incomplete absorption was noted at the posterior pole with 308 nm and complete absorption was noted with 193 nm. The extinction in the anterior part of aphakic eyes (the first 6 mm) was 4.2/cm for 308 nm, meaning ...

1990-11-01

403

Interaction of water with epoxy.  

Energy Technology Data Exchange (ETDEWEB)

The chemistries of reactants, plasticizers, solvents and additives in an epoxy paint are discussed. Polyamide additives may play an important role in the absorption of molecular iodine by epoxy paints. It is recommended that the unsaturation of the polyamide additive in the epoxy cure be determined. Experimental studies of water absorption by epoxy resins are discussed. These studies show that absorption can disrupt hydrogen bonds among segments of the polymers and cause swelling of the polymer. The water absorption increases the diffusion coefficient of water within the polymer. Permanent damage to the polymer can result if water causes hydrolysis of ether linkages. Water desorption studies are recommended to ascertain how water absorption affects epoxy paint.

2009-07-01

404

European Commission - Environment  

Wastenet

...Species - see CITES Trade of Dangerous Chemicals Transport and Environment U Urban Environment Use of natural resources V Volatile Organic Compounds W Waste Landfills Waste electrical and electronic equipment - see WEEE Waste incineration Waste legislation - reporting Waste management planning Waste oils Waste shipments Waste water - see Urban waste water Water Bathing Water Drinking water Floods Marine environment Urban waste water Water Framework Directive WEEE - Waste Electric and Electronic Equipment Wildlife ...

405

Phosphorus and nitrogen in the eutrophication of waters. Fosfori ja typpi vesien rehevoeittaejinae - vaikutusten arviointi  

Energy Technology Data Exchange (ETDEWEB)

This report is a summary of the contribution of nitrogen and phosphorus in the eutrophication process of inland and coastal waters. Special attention was paid to the mechanisms of these nutrients in regulating biological processes and to the methods available in estimating their effects in the eutrophication of water bodies. The report includes five chapters which are entitled: Introduction, which is a general background to the subject with special attention to the requirements of the Finnish Water Act. Phosphorus and nitrogen as factors regulating biological processes. The topics included are: definition of eutrophication, forms of phosphorus and nitrogen and their sources to inland and coastal waters, effects of these nutrients as growth factors of phytoplankton and macrophytes and consequences of eutrophication. Estimation of the effects of phosphorus and nitrogen. The topics discussed from the point ...

1992-01-01

406

Major roles of water chemistry for safe and reliable nuclear power plant operation. Research committee on water chemistry standard  

International Nuclear Information System (INIS)

The research committee of the Atomic Energy Society of Japan on water chemistry standard aims at establishing the private standard of water chemistry of nuclear power plants. The committee gathers up 'BWR water chemistry management manual', 'PWR primary system water chemistry management manual' and 'PWR water chemical analysis standard method', and furthermore aims at the standardization of those in future. Looking back on the committee's activities for the past four years, latest results of research of water chemistry mainly contributing to safe and reliable nuclear power plants were described with the future perspective of water chemistry and a demanded break-through. (T.T.)

2007-05-01

407

Laser-fluorescence determination of trace uranium in hot spring water, geothermal water and tap water in Xi'an Lishan region  

International Nuclear Information System (INIS)

Using the Laser-Fluorescence technique, an investigation was made, adopting the standard mix method, on trace uranium concentrations in hot spring water and geothermal water from Lishan region, and in tap water from some major cities in Shanxi province. Totally 40 samples from 27 sites were investigated. Measurement showed that the tap water contains around 10"-"6 g/L of uranium, whose concentrations in both hot spring water and geothermal water are 10"-"5 g/L. Most of samples are at normal radioactive background level, some higher contents were determined in a few samples

2002-03-01

408

Corrosion behavior of iron and nickel base alloys in high temperature and pressure water  

International Nuclear Information System (INIS)

In equipment industries, the equipments handling industrial water and pure water are numerous. In power generation including nuclear power generation, water serves as a working medium. Review is made on the experiences in the corrosion of iron and nickel base alloys in high temperature, high pressure water and the results of researches derived from them. Under high temperature and high pressure, carbon steel, low alloy steel, stainless steel and high nickel alloy cause corrosion even in pure water. But in the case of serious corrosion, chlorine, oxygen, alkali and others in water take part. The following matters are described: corrosion by steam; stress corrosion cracking in pure water; corrosion by impurities in high temperature, high pressure pure water, i.e. chlorine ions, dissolved oxygen, and alkali; corrosion under ...

409

AquaMagna Water Conditioner and Descaler  

Wastenet

...AquaMagna Water Conditioner and Descaler OCETA Environmental Technology & Business Profiles AQUAMAGNA WATER CONDITIONER AND DESCALER CAT. #03-018 CONTACT: Magna-Tek ...removal high-strength ceramic magnet no energy input The AquaMagna Water Conditioner and Descaler is a non-chemical method of water treatment. The technology uses ... Figure 1: The AquaMagna Water Conditioner and Descaler PROCESS/ PRODUCT APPLICATION: hard water domestic water process water reverse osmosis heat exchangers cooling ... For once-through or recirculating heating or cooling equipment, the AquaMagna descaler improves thermal efficiencies and reduces downtime. Figure 2 illustrates a cross-section ...

410

A novel domestic electric water heater model for a multi-objective demand side management program  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a novel domestic hot water heater model to be used in a multi-objective demand side management program. The model incorporates both the thermal losses and the water usage to determine the temperature of the water in the tank. Water heater loads are extracted from household load data and then used to determine the household water usage patterns. The benefits of the model are: (1) the on/off state of the water heater and temperature of the water in the tank can be accurately predicted, and (2) it enables the development of water usage profiles so that users can be classified based on usage behaviour. As a result, the amount of ancillary services and peak shaving that can be achieved are accurately predictable and can be maximized without adversely affecting users. (author)

2010-12-15

411

Water | Editorial Board  

Wastenet

...Tota-MaharajE-Mail: Interests: water and wastewater treatment, environmental engineering and sustainable systems; sustainable water management; sustainable urban drainage systems (SUDS); combined renewable energy applications with reverse osmosis desalination; microbial fuel cells for bioenergy production and treatment of urban wastewater; solar photocatalytic treatment and disinfection of water/wastewater Dr. Simon Toze CSIRO Land and Water, Queensland Bioscience Precinct - St Lucia, 306 Carmody Road, St Lucia QLD 4067,...

412

Changes in water dependence of Russian economy  

British Library Electronic Table of Contents (United Kingdom)

Indicators of source water use in different economic branches, water consumption in recycling and recycling-successive water supply in 1980?2006 are analyzed. Trends were identified in variations in specific water consumption in industry, agriculture, and municipal economy. Territorial differentiation of wetness indicators of regional product over federal districts and constituent territories of the RF is shown. Wetness values of gross domestic product in different economies are compared.

2010-01-01

413

USGS Arkansas Water Science Center  

Science.gov (United States)

number Fax (501) 228-3600 (501) 228-3601 Surface Water Data Information Requests Bill Baldwin (501) 228-3602 Surface Water General Information Jaysson Funkhouser (501) 228-3663...

2011-09-23

414

The BEACHES Study: health effects and exposures from non-point source microbial contaminants in subtropical recreational marine waters  

UK PubMed Central (United Kingdom)

Background Microbial water-quality indicators, in high concentrations in sewage, are used to determine whether water is safe for recreational purposes. Recently, the use of these indicators...Full Text Available

2010-10-01

415

Study on the separation characteristics of tritiated water vapor adsorption.  

Science.gov (United States)

In order to reduce the air concentration of (sup 3)H in the reactor buiIding of Wolsung Heavy Water Reactor, a computer code for estimation of adsorption behavior was programmed based on an equation derived for analysis of water vapor adsorption, and a ba...

1991-01-01

416

Rational protection of the quality of coastal waters by means of integrated, real-time management of the water environment; Proteccion racional de la calidad de las aguas costeras mediante la gestion integrada y en tiempo real del medio hidrico  

Energy Technology Data Exchange (ETDEWEB)

Before the implementation Water Framework directive, it was usual to forget that a good environment protection of the receiving waters needs a correct and coordinated operation of the subsystems of the water cycle, specially sewerage system, WWTP and receiving waters. This explains that most of the countries have focused their efforts in the treatment of dry weather flows forgetting the management of wet weather flows. Actually the idea that a sewerage system or a WWTP can not be planned or managed independently without considering the effects on the receiving waters is commonly accepted because not only each one of these systems must work correctly but also it is required a minimum impact in the receiving waters of the sewerage and WWTP overflows in dry and wet weather. All these links will affect the management strategy of the sewerage system (storm ...

2005-07-01

417

On the water-chemical regime in steam generators at NPP  

British Library Electronic Table of Contents (United Kingdom)

The effect of the water-chemical regime (WCR) on damage sustained by heating surfaces of steam generators at NPP is analyzed. It is indicated that phosphate treatment with minimal excesses of phosphates in the steamgenerator water is the most optimal method of managing the WCR regime of horizontal steam generators.

2006-01-01

418

Nodule and Leaf Nitrate Reductases and Nitrogen Fixation in Medicago sativa L. under Water Stress  

UK PubMed Central (United Kingdom)

The effect of water stress on patterns of nitrate reductase activity in the leaves and nodules and on nitrogen fixation were investigated in Medicago sativa L. plants watered 1 week...Full Text Available

1982-02-01

419

Monte Carlo modeling of 60Co HDR brachytherapy source in water and in different solid water phantom materials  

UK PubMed Central (United Kingdom)

The reference medium for brachytherapy dose measurements is water. Accuracy of dose measurements of brachytherapy sources is critically dependent on precise measurement of the source–detector...Full Text Available

2010-01-01

420

Modeling of soluble impurities distribution in the steam generator secondary water  

Energy Technology Data Exchange (ETDEWEB)

A model was developed to compute concentration of impurities in the WWER 440 steam generator (SG) secondary water along the tube bundle. Calculated values were verified by concentration values obtained from secondary water sample chemical analysis. (orig.). 2 refs.

1997-12-31

421

Measurement of the Water Potential of Stored Potato Tubers 1  

UK PubMed Central (United Kingdom)

A method of measuring the water potential of stored potato tubers (Solanum tuberosum L.) was needed to investigate the relationship of bacterial soft rot in tubers to water potential....Full Text Available

1985-11-01

422

Invasion and control of water hyacinth (Eichhornia crassipes) in China*  

UK PubMed Central (United Kingdom)

By the time of primary 21st century, water hyacinth had become a serious environmental problem in China. Water hyacinth contributes to the major part of ecological hazards from the invasion of foreign...Full Text Available

2006-08-01

423

In vivo Visualization of the Water-refilling Process in Xylem Vessels Using X-ray Micro-imaging  

UK PubMed Central (United Kingdom)

Background and AimsXylem vessels containing gases (embolized) must be refilled with water if they are to resume transport of water through the plant, so refilling is of great importance...Full Text Available

2008-03-01

424

Heat-transfer analysis of the plum brook reactor - NASA Technical ...  

Science.gov (United States)

average bulk water temper ature rise, OF bulk water temperature at elevation z, OF bulk water temperature in channels 0 and 1, O F film temperature, OF ...

425

Device for controlling water supply to nuclear reactor  

International Nuclear Information System (INIS)

Object: To smoothly control automatic water supply for realizing stable operation of a nuclear reactor by providing a flow rate limiting signal selection circuit and a preferential circuit in a water supply control device for a nuclear reactor wherein the speed of a recirculation pump may be changed in two-steps. Structure: Opening angle signals for a water supply regulating valve are controlled by a nuclear reactor water level signal, a vapor flow rate signal and a supplied water flow rate signal through an adder and an adjuster in response to a predetermined water level setting signal. When the water in the reactor is maintained at a predetermined level, a selection circuit receives a water pump condition signal for selecting one of the signals from a supplied water rate limiting signal generator ...

427

Bacterial indicators of risk of diarrhoeal disease from drinking-water in the Philippines.  

UK PubMed Central (United Kingdom)

Inadequate measures of water quality have been used in many studies of the health effects associated with water supplies in developing countries. The present 1-year epidemiological-microbiological study...Full Text Available

1991-01-01

428

Increasing concentrations of trihalomethanes (THMs) in a drinking water distribution network; Trihalometanos (THMs) en una red de distribucion de agua potable en alta  

Energy Technology Data Exchange (ETDEWEB)

THMs are disinfection by-products (DBPs) generated during water chlorination. Concentration of individual and total THMs, depends on treatment process and THMs precursors level. ATLL water utility has two DWTP (Llobregar and Ter) that produce and supply drinking water to Barcelona and regional area. This work studies the levels of THMs along the ATLL distribution system (450 km). Although, no differences were observed along water pipes system, changes of water resource and mix procedures were related. (Author) 12 refs.

1999-07-01

429

Fundamental R and D program on water chemistry of supercritical pressure water under radiation field  

International Nuclear Information System (INIS)

In a supercritical water-cooled reactor, property of water changes significantly around the critical point. It is expected that irradiation and change of water property will affect the chemistry and material corrosion. Deep understanding of interactions between supercritical water and materials under irradiation is important. However, comprehensive data on radiolysis, kinetics, corrosion and thermodynamics have not been obtained due to the severe experimental condition. To get such data by experiments and computer simulations, a national program funded by Ministry of Education, Culture, Sports, Science and Technology (MEXT) has been started since December 2002. (author)

2003-09-15

430

Evaluation of tritiated water retention capacity of fusion reactor concrete building  

Energy Technology Data Exchange (ETDEWEB)

In this paper the diffusion of tritiated water vapor into concrete walls is studied to evaluate tritiated water retention capacity of a fusion reactor concrete building. Using a model of the tritiated water diffusion determined form experimental results, depth profiles of tritiated water in concrete are calculated in the case of being exposed to air containing tritiated water vapor during the normal operational condition of a fusion reactor. A 0.5-m-thick concrete is sufficient for reactor hall walls from a viewpoint of the tritium containment.

1992-03-01

431

Evaluation of tritiated water retention capacity of fusion reactor concrete building  

International Nuclear Information System (INIS)

In this paper the diffusion of tritiated water vapor into concrete walls is studied to evaluate tritiated water retention capacity of a fusion reactor concrete building. Using a model of the tritiated water diffusion determined form experimental results, depth profiles of tritiated water in concrete are calculated in the case of being exposed to air containing tritiated water vapor during the normal operational condition of a fusion reactor. A 0.5-m-thick concrete is sufficient for reactor hall walls from a viewpoint of the tritium containment.

432

Water management studies in PEM fuel cells, part III: Dynamic breakthrough and intermittent drainage characteristics from GDLs with and without MPLs  

British Library Electronic Table of Contents (United Kingdom)

The transport of liquid water and gaseous reactants through a gas diffusion layer (GDL) is one of the most important water management issues in a proton exchange membrane fuel cell (PEMFC). In this work, the liquid water breakthrough dynamics, characterized by the capillary pressure and water saturation, across GDLs with and without a microporous layer (MPL) are studied in an ex-situ setup which closely simulates a real fuel cell configuration and operating conditions. The results reveal that recurrent breakthroughs are observed for all of the GDL samples tested, indicating the presence of an intermittent water drainage mechanism in the GDL. This is accounted for by the breakdown and redevelopment of the continuous water paths during water drainage as demonstrated by Haines jumps. For GDL ...

2010-01-01

433

Water You Engineering? An Activity to Develop Water-Quality Awareness  

Science.gov (United States)

Water is one of our most precious resources. However, for many in the United States, having fresh, safe drinking water is taken for granted, and due to this perceived lack of relevance, students may not fully appreciate the luxury of having safe running water--in the home. One approach to resolving water-quality issues in the United States may reside in providing education that presents accurate information in a meaningful way. Accordingly, this article describes a unit designed to emphasize the importance of water-quality testing and purification and to introduce students to local water-quality issues. The engineering-based module of this eighth-grade science activity is particularly important due to the design-build-test component. (Contains 5 figures.)

2009-04-01

434

Thermal- and radiation-induced interactions of water on U02 surfaces.  

Energy Technology Data Exchange (ETDEWEB)

Most plans for the disposition of surplus nuclear materials involve storage in sealed containers where the evolution of gases from reactions of adsorbed water could present both pressure and flammability hazards[l] . Despite efforts such as calcining the material to minimize the water content prior to packaging, both residual moisture and readsorbed water may be present in the final containers . Given the anticipated temperature excursions during transportation and storage, this water may thermally desorb, increasing the pressure, and/or thermally dissociate to produce H2 gas, increasing flammability hazards . In addition, the radiation from the nuclear material may induce radiolysis of the water with the likely products being water vapor, H2, 02 and H2O2. In order to better understand the relative importance of the thermal- and radiationinduced chemistry, we ...

2003-01-01

435

Simulation of ground-water flow in the basin-fill aquifer of the Tularosa Basin, south-central New Mexico, ...  

Science.gov (United States)

... percent by interbasin ground-water flow into the Hueco Bolson, and 2 percent by flow into creeks and ... ...

436

Radon concentration measurements at water reservoirs  

International Nuclear Information System (INIS)

Ground water is treated in the Czech Republic so that small water tanks are built above each water source to serve the primary ground water treatment; water so pretreated is then concentrated in large basins for subsequent treatment. Some water tanks where the first contact of the ground water with air takes place were selected as sites predisposed to radon accumulation. The examination was carried out near the town of Jihlava, where the bedrock contains slightly elevated radium concentrations. The average radon concentrations lay within the region of 2-4 kBq/m"3; the instantaneous values, however, exhibited appreciable periodical variations during the day. The relatively high radon concentrations will not pose a marked hazard for the personnel because the employees only reside at the sites in question for 10 to 15 minutes within 2 days, not ...

1998-09-09

438

Pipe Freeze Prevention for Passive Solar Water Heaters Using a Room-Air Natural Convection Loop: Preprint  

Energy Technology Data Exchange (ETDEWEB)

Conference paper regarding research in the use of freeze prevention for passive solar domestic water heating systems.

2006-05-01

439

Performance of single cylinder, direct injection diesel engine using water fuel emulsions  

Energy Technology Data Exchange (ETDEWEB)

A single cylinder diesel engine study of water-in-diesel emulsions was conducted to investigate the effect of water emulsification on the engine performance and gases exhaust temperature. Emulsified Diesel fuels of 0, 5, 10, 15 and 20 water/diesel ratios by volume were used in a single cylinder, direct injection diesel engine, operating at 1200-3300 rpm. The results indicate that the addition of water in the form of emulsion improves combustion efficiency. The engine torque, power and brake thermal efficiency increase as the water percentage in the emulsion increases. The average increase in the brake thermal efficiency for 20% water emulsion is approximately 3.5% over the use of diesel for the engine speed range studied. The proper brake specific fuel consumption and gases exhaust temperature decrease as the percentage of water in the ...

2004-03-01

440

Oreochromis lepidurus  

Science.gov (United States)

... Marine transport and oil disposal by boats and Matadi pose threats in the region. When the water ... Marine transport and oil disposal by boats and Matadi pose threats in the region. When the water ... ...

441

Oceanographic Processes and Marine Productivity in Waters Offshore ...  

Science.gov (United States)

Jun 16, 2011 ... Title: Chapter 21: Oceanographic Processes and Marine Productivity in Waters Offshore of Marbled Murrelet Breeding Habitat ...

442

Ocean Water: Density  

Science.gov (United States)

This site explains how temperature, pressure, and salinity work together to determine the density of ocean water. The three density layers of the ocean are described by means of text description and a graphic illustration.

443

NASA 11x:/,3 '/t.z- - NASA Technical Reports Server  

Science.gov (United States)

_! Packaging, Cleanlines_, Preparation j Handling ..... 35. 'I. 40. WATER ................ , ......... Sterile, High Purity, Ethylene Glycol-Water Solutions. Requirement For . ...

444

N. Mariana Islands Wildlife Action Plan  

Science.gov (United States)

... will utilize man-made habitats, including artificial wetlands, waste water ponds, water hazards on golf courses, and an abandoned ... ...

445

Mathematical modeling of a direct contact humidification?dehumidification desalination process  

British Library Electronic Table of Contents (United Kingdom)

Using air as a carrier gas is common in humidification?dehumidification desalination processes. A computer program was written using mass and energy balances for modeling the process behavior. The parameters considered in this work were inlet air and fresh water recycle temperatures, inlet air flow rate, saline water and fresh water recycle flow rates, and saline water to air flow ratio. Results of simulation showed that increasing inlet air and fresh water recycle flow rate increases fresh water production. It was also found that heating the inlet air to humidification column or cooling the inlet water to dehumidification column increases the production rate but increasing water to air flow ratio in a humidifier leads to a lower production rate. The predicted effects of the parameters on ...

2009-01-01

446

Managing a large outbreak of cryptosporidiosis: how to investigate and when to decide to lift a 'boil water' notice.  

Science.gov (United States)

The largest outbreak of cryptosporidiosis reported in the United Kingdom, involving 575 confirmed cases (of which 474 met an agreed case definition), occurred in the county of Devon during August and September of 1995. The descriptive epidemiology supports the hypothesis that the outbreak was associated with the consumption of cold tap water in the area served by a particular water treatment works. Cryptosporidium oocysts were detected in treated water samples at the time of the outbreak. Although the epidemiological analysis provided strong circumstantial evidence of a waterborne outbreak, the data were not recorded in a manner that made them admissible in criminal proceedings taken by the Drinking Water Inspectorate against the water company involved. The need to carry out an analytical study in conjunction with the identification and characterisation of the pathogen in the ...

2002-09-01

447

MTF ' MISSISSIPPI SOUND REMOTE SENSING STUDY I 19 SEPTEMBER 1972  

Science.gov (United States)

metric temperatures has been prepared showing the surface water temper- ... occasion, gray levels show different densities for similar water temper- ...

448

JPRS Report, Science & Technology, China: Energy  

Science.gov (United States)

... should give full con- As for the effects of the Three Gorges on the mouth of sideration to the rising water process and water temper- the river, the ...

1991-08-23

450

Ground-Water Data for the Suck Creek Area of Walden Ridge ...  

Science.gov (United States)

... Where Suck Creek enters the river, a formidable whirlpool and 2 Ground-water data for the Suck Creek area of Walden Ridge, Southern ...

2011-05-14

451

Fetal cardiotocography before and after water aerobics during pregnancy  

UK PubMed Central (United Kingdom)

ObjectiveTo evaluate the effect of moderate aerobic physical activity in water on fetal cardiotocography patterns in sedentary pregnant women.MethodIn...Full Text Available

452

Equipment for a central heating system with expansion tank, pressure control, water loss supply, de-aeration, recording and control; Apparaat t.b.v. C.V.-installatie met expansievat, drukregeling, waterverliessuppletie, ontluchting, registratie en controle  

Energy Technology Data Exchange (ETDEWEB)

The very low-pressure expansion tank of the title invention is connected to the water in the central heating installation via a connecting pipe with a pump and valves on one side, and on the other side the tank is connected via a connecting pipe with valve to the tap water mains, so that the supply of water can be regulated automatically. Within the expansion tank contact with the outside air is not possible because of an air/water separating floater. By means of recording and control (also remote) of the contents of the expansion tank, the installation pressure and the quantity of supplied water from the expansion tank and the tap water mains, failures and water damage are prevented. 4 figs.

1995-09-01

453

Ecology of Vibrio mimicus in aquatic environments.  

UK PubMed Central (United Kingdom)

An environmental study was done to examine the prevalence of Vibrio mimicus in some aquatic environments of Dhaka, Bangladesh, and of Okayama, Japan. Water samples from Dhaka environments and water...Full Text Available

1989-08-01

454

Density: Sea Water Mixing and Sinking - Aquarius - NASA  

Science.gov (United States)

density is slightly higher, its electrical conductivity is much higher, and it is slightly ... Sea water has characteristic properties (e.g. density) that are independent of ...

455

Assessing vineyard water status using the reflectance based Water Index  

British Library Electronic Table of Contents (United Kingdom)

In the Mediterranean arc, vines for wine production are mainly grown without the support of irrigation. Under such conditions, site variables affecting the extent and seasonal timing of water deficits are the dominant environmental constraints for grape production. Moreover, water availability and vine water status are the factors most comprehensively determining fruit composition and, thus, wine quality. Therefore, monitoring the extent of water stress in vines might be a valuable tool for the optimisation of grape yield and quality. The objective of this study was to evaluate the feasibility of using the reflectance based Water Index (WI) to estimate vine water status at the leaf and canopy levels. The study was conducted on Vitis vinifera cv. Chardonnay potted plants submitted to contra...

2010-01-01

456

Aqueous water-soluble soap lubricant concentrates and aqueous lubricants containing same  

Energy Technology Data Exchange (ETDEWEB)

The inclusion of neodecanoic acid in aqueous water-soluble soap lubricants reduces viscosity, and improves lubricity effectiveness.

1981-06-23

457

Anesthetic stimulation of insect water receptors.  

UK PubMed Central (United Kingdom)

Halothane, chloroform, and carbon tetrachloride, in the vapor and liquid phases, stimulate the water receptor of the blowfly Phormia regina. There are three successive phases of response to long-lasting...Full Text Available

1976-09-01

458

Understanding and predicting soot generation in turbulent non-premixed jet flames.  

Energy Technology Data Exchange (ETDEWEB)

This report documents the results of a project funded by DoD's Strategic Environmental Research and Development Program (SERDP) on the science behind development of predictive models for soot emission from gas turbine engines. Measurements of soot formation were performed in laminar flat premixed flames and turbulent non-premixed jet flames at 1 atm pressure and in turbulent liquid spray flames under representative conditions for takeoff in a gas turbine engine. The laminar flames and open jet flames used both ethylene and a prevaporized JP-8 surrogate fuel composed of n-dodecane and m-xylene. The pressurized turbulent jet flame measurements used the JP-8 surrogate fuel and compared its combustion and sooting characteristics to a world-average JP-8 fuel sample. The pressurized jet flame measurements demonstrated that the surrogate was representative of JP-8, with a somewhat higher tendency to soot formation. The premixed flame measurements revealed that flame temperature has a ...

2010-10-01

459

Thermal and tectonic history of the Ordos Basin, China: Evidence from apatite fission track analysis, vitrinite reflectance, and K-Ar dating  

Energy Technology Data Exchange (ETDEWEB)

Apatite fission track analysis, vitrinite reflectance data, and K-Ar dating of Permian-Carboniferous and Mesozoic core samples have been successfully integrated to reconstruct the thermal and tectonic history of the Ordos basin, China. Apatite fission track ages of Carboniferous-Jurassic sedimentary rocks range between 3 and 137 Ma, and are significantly younger than the stratigraphic ages. Confined fission track lengths demonstrate exclusively mixed length distribution, indicating complex thermal history. The data suggest that the samples must have all experienced higher paleotemperatures in the past. Mean virtinite reflectance values (R{sub o}) of the Triassic rocks range from 0.61 to 1.06%, giving a high coalification gradient of 0.36%/km and suggesting a high paleothermal gradient of 57{degrees}C/km. Permian-Carboniferous rocks have R{sub o} values on the order of 1.0-3.0%, and locally up to 4.0-6.0%. Some high R{sub o} values coincide with positive gravity and magnetic anomalies. ...

1996-07-01

460

Strategy and management of network security at KEK  

International Nuclear Information System (INIS)

Recently the troubles related to the network security have often occurred at KEK. According to their security policy, the authors have started the strategy against the daily attacks. It consists of two fundamental things; the monitoring and the access control. To monitor the network, the authors have installed the intrusion detection system and have managed it since 1998. For the second thing, the authors arranged three categories to classify all hosts (about 5000 hosts) at KEK according to their security level. To realize these three categories, the authors filter the incoming packet from outside KEK whether it has a SYN flag or not. The network monitoring and the access control produced good effects in keeping the security level high. Since 2000 the authors have started the transition of LAN from shared-media network to switched network. Now almost part of LAN was re-configured and in this new LAN 10 Mbps 100 Mbps/1Gbps Ethernet are supported. Currently the ...

2001-09-03

461

START: An essential step in a new era  

Energy Technology Data Exchange (ETDEWEB)

After more than nine years of negotiations, the US and the Soviet Union signed the Strategic Arms Reduction Treaty (START) in Moscow on July 31, 1991. While the world has changed dramatically since 1982 when the START negotiations began, the treaty remains very much in the US interest. START exacts deep cuts in the most destabilizing and dangerous US and Soviet strategic weapons, and will lead to substantial overall reductions in the strategic nuclear forces of both sides. Moreover, the agreement will create a formal, structured, and predictable strategic environment. It will also impose on the Soviet Union or its successors a legally binding set of obligations that will be in effect for many years, regardless of changes in leadership or form of government. START, with its extensive series of intrusive, cooperative, and technical verification measures, will greatly enhance US knowledge about Soviet strategic nuclear forces and activities. The force reductions, ...

1991-11-01

462

Precious metal enrichment in the Platreef, Bushveld Complex, South Africa: evidence from homogenized magmatic sulfide melt inclusions  

Science.gov (United States)

Magmatic sulfide deposits are the most significant source of platinum-group elements (PGE) in the world. Key to understanding their genesis is determining the processes and timing of sulfide saturation, metal enrichment and crustal contamination. In this study, we have identified droplets of magmatic sulfide from the Platreef, South Africa, where droplets of sulfide have been trapped in the earliest crystallising phase, chromite. Due to their early entrapment at high temperatures, metal concentrations and ratios that they display are indicative of a very early-stage sulfide liquid in the system, as they will have cooled and fractionated within an essentially closed system, unlike interstitial blebs that crystallise in an open system as the magma cools. Analysis of these droplets in an opaque mineral like chromite by LA-ICP-MS is problematic as some of the fractionated inclusion is necessarily lost during cutting and polishing to initially identify the inclusion. This particularly ...

2011-06-01

463

Physical Modelling of Axisymmetric Turbulent Impinging Jets as used within the Nuclear Industry for Mobilisation of Sludges  

Energy Technology Data Exchange (ETDEWEB)

The impingement of a fluid jet onto a surface has broad applications across many industries. Within the UK nuclear industry, during the final stages of fuel reprocessing, impinging fluid jets are utilised to mobilise settled sludge material within storage tanks and ponds in preparation for transfer and ultimate immobilisation through vitrification. Despite the extensive applications of impinging jets within the nuclear and other industries, the study of two-phase, solid loaded, impinging jets is limited, and generally restricted to computational modelling. Surprisingly, very little fundamental understanding of the turbulence structure within such fluid flows through experimental investigation is found within the literature. The physical modelling of impinging jet systems could successfully serve to aid computer model validation, determine operating requirements, evaluate plant throughput requirements, optimise process operations and support design. Within this project a method is ...

2008-07-01

464

Host based internet protocol (IP) packet analysis to enhance network security  

International Nuclear Information System (INIS)

Data communication in a computer network environment is facing serious security threats from numerous sources such as viruses, worms, Zombies etc. These threats can be broadly characterized as internal or external security threats. Internal threats are mainly attributed to sneaker-nets, utility modems and unauthorized users, which can be minimized by skillful network administration, password management and optimum usage policy definition. The external threats need more serious attention as these attacks are mostly coming from public networks such as Internet. Frequency and complexity of such attacks is much higher as compared to internal attacks. This paper presents a host based network layer screening of external and internal IP packets for logging, analyzing and real-time detection of possible IP spoofing and Denial of Service attacks. This work can also be used in tuning security rules definition for gateway firewalls. Software has been developed which intercepts IP traffic and ...

2007-01-01

465

Assessing the internal mechanical integrity of power transformers using vibration tests  

Energy Technology Data Exchange (ETDEWEB)

Machine condition monitoring (MCM) has the capability to predict equipment maintenance needs which can reduce forced down-time and facilitate the avoidance of catastrophic failures and the consequential secondary damage. It can be used to allow confident deferral of routine maintenance, and improve equipment performance, availability, reliability and safety. In order to capitalize on the potential benefits of MCM directed toward power transformers two types of vibration tests were conducted on transformers owned and operated by Cargill Inc. and IES Utilities at the Bridgeport corn plant in Eddyville, Iowa. These tests involved collecting vibration signals from the transformer tank walls during transformer energization at no-load and during steady state operation at various loads. These vibration signals were then used to detect deterioration of internal mechanical integrity. Both types of tests conducted on the transformers at the Eddyville plant show considerable potential for use as ...

1996-12-31

466

The numerical simulation on low-level radioactive waste water, low-temperature cooling water drained effect of implement from the Daya Bay Nuclear Power Plant  

International Nuclear Information System (INIS)

In this paper, we calculated the radioactive concentration distribution of radioactive waste water, the temperature distribution of drained cooling water and the effect of implement from the Daya Bay Nuclear Power Plant on nearby waters range, discussed and analysed some problems of computational results and computation with Alternating Direction Implicit Method (ADI). The contents of the article included: the establishment of two-dimension tidal current equation, radioactive waste water pollutant dispersion equation and cooling water heat convection diffusion equation, the numerical difference calculation model of tidal current field, concentration field as well as temperature field, effect impingement with ADI method, numerical calculation results. The result of research showed that: when the Daya Bay Nuclear Power Plant is on normal operation and after the low level radioactive ...

467

High quality water supply system; Joshitsusui kyokyu system  

Energy Technology Data Exchange (ETDEWEB)

This paper, firstly, introduces the background in developing a high quality water supply system, in which the drinking water system is isolated inside a building. Results of questionnaire on the high quality service water are illustrated. The results of questionnaire have revealed that the high quality service water is extremely interested. Then, are described the target quality of high quality water, the constitution of high quality water supply system, the treatment process, the measures to secure safety and sanitary, and the method of maintenance. The high quality water is produced through the activated charcoal absorption treatment, membrane treatment, ozonation, cooling, mineral addition, and disinfection of city water. Furthermore, application examples of this system adopted to a department store and a bachelor ...

1995-01-15

468

Environmental levels of tritium, 2  

International Nuclear Information System (INIS)

In an attempt to obtain basic data for evaluation of exposure doses in Niigata Prefecture, the concentrations of tritium in atmospheric water, precipitation, river water, and tap water were measured. Samples of atmospheric water, river water, and tap water were collected once for 2 weeks; and precipitation collected for one week was used as sample. The concentration of atmospheric tritium depended on the concentration of tritium in moisture and the content of water in atmosphere. Tritium levels were high in May, November and March, and low in September. Regarding tritium concentrations, there was a good correlation between atmospheric water and precipitation. Tritium concentrations in both of them varied from sample to sample. The concentrations of tritium in river and tap water tended to be high ...

469

Treatment of Difficult Wastes with Molten Salt Oxidation  

Energy Technology Data Exchange (ETDEWEB)

Molten salt oxidation (MSO) is a good alternative to incineration for the treatment of a variety of organic wastes such as explosives, low-level mixed waste streams, PCB contaminated oils, spent resins and carbon. Since mid-1990s, the U.S. Army Defense Ammunition Center (DAC) and the Department of Energy (DOE) have jointly invested in MSO development at the Lawrence Livermore National Laboratory (LLNL). LLNL first demonstrated the MSO process for the effective destruction of explosives, explosives-contaminated materials, and other wastes on a 1.5-kg/hr bench-scale unit, and then in an integrated MSO facility capable of treating 8 kg/hr of low-level radioactive mixed wastes. Several MSO systems have been built with sizes up to 10 ft in height and 16 inches in diameter. LLNL in 2001 completed a MSO plant for DAC for the destruction of explosives-contaminated sludge and explosives-contaminated carbon. We will present in this paper our latest demonstration data and our ...

2003-02-21

470

Three-dimensional multispecies current density simulation of molten-salt electrorefining  

Energy Technology Data Exchange (ETDEWEB)

This study presents three-dimensional simulation results of multispecies and multi-reaction electrorefining for spent nuclear waste treatment. Fluid-dynamic behavior of electrorefining is analyzed by commercial computational fluid-dynamics code. The results of local fluid dynamics are coupled with one-dimensional electrochemical reaction analysis code in order to predict local current density distribution. The new approach shows current distribution patterns over the cathode surface in LiCl-KCl molten-salt electrolyte. The current density distribution patterns are analyzed for various electrode rotational speeds and diverse applied currents and the results show a good agreement with general principle of mass transfer observations. Spatially periodic and vertically striped pattern of current density is predicted at the cathode side due to mass transfer depression at separation points. These slow mass transfer regions are vulnerable to be contaminated by transuranic ...

2010-07-30

471

The role and impact of rubber in poly(methyl methacrylate)/lithium triflate electrolyte  

British Library Electronic Table of Contents (United Kingdom)

In this research, new thin freestanding films of poly(methyl methacrylate) (PMMA)/50% epoxidised natural rubber (ENR 50) were doped with lithium triflate, LiCF3SO3 salt was prepared by a solvent casting method. The incorporation of ENR 50 is found to increase the conductivity of PMMA/LiCF3SO3 by two orders of magnitude at room temperature. The highest conductivity achieved was 5.09x10-5Scm-1 at room temperature when 60% of LiCF3SO3 salt was introduced into the PMMA blend containing 10% ENR 50. The formation of excessive hydrogen bonds and interchain crosslinking limit the performance of the blend at higher concentrations of ENR 50. The ionic conduction mechanisms in PMMA/ENR 50/LiCF3SO3 electrolytes obey the Arrhenius rule in which the ion transport in these materials is thermally assisted...

2006-01-01

472

The NIR Upgrade to the SALT Robert Stobie Spectrograph  

CERN Document Server

The near infrared (NIR) upgrade to the Robert Stobie Spectrograph (RSS) on the Southern African Large Telescope (SALT), RSS/NIR, extends the spectral coverage of all modes of the visible arm. The RSS/NIR is a low to medium resolution spectrograph with broadband imaging, spectropolarimetric, and Fabry-Perot imaging capabilities. The visible and NIR arms can be used simultaneously to extend spectral coverage from approximately 3200 A to 1.6 um. Both arms utilize high efficiency volume phase holographic gratings via articulating gratings and cameras. The NIR camera is designed around a 2048x2048 HAWAII-2RG detector housed in a cryogenic dewar. The Epps optical design of the camera consists of 6 spherical elements, providing sub-pixel rms image sizes of 7.5 +/- 1.0 um over all wavelengths and field angles. The exact long wavelength cutoff is yet to be determined in a detailed thermal analysis and will depend on the semi-warm instrument cooling scheme. Initial estimates ...

2006-01-01

473

Synthesis of Poly (D L-lactide-co-dl-3,6 dimethyl-morpholine, 2,5 - dione)  

International Nuclear Information System (INIS)

Polypeptides, copolymers of #alpha#-amino acids and #alpha#-hydroxy acids, could prove to be a valuable new class of synthetic biodegradable polymers. In this paper. steps in synthesis of poly (dl-lactide-co-3, 6-dimethylmorpholine-2,5-dione) from dl-lactide and dl-3,6-dimethylmorpholine-2,5-dione was explained. dl-Lactide was synthesized from lactic acid. In the reaction of 2-bromopropionyl chloride and dl-alanine, N-(2-bromopropionyl)-dl-alanine was prepared and this material was converted to its salt and finally this salt was converted to 3,6-dimethylmorpholine-2,5-dione in a sublime r. These two monomers, that is d l-lactide and dl-3,6-dimethylmorpholine-2,5-dione was polymerized by ring-opening polymerization. F T-IR, "1H NMR, "1"3C NMR Spectra were used for structure elucidation of all intermediate compounds and final product.

2001-09-01

474

Synthesis and characterization of Al{sub 2}O{sub 3}/ZrO{sub 2}, Al{sub 2}O{sub 3}/TiO{sub 2} and Al{sub 2}O{sub 3}/ZrO{sub 2}/TiO{sub 2} ceramic composite particles prepared by ultrasonic spray pyrolysis  

Energy Technology Data Exchange (ETDEWEB)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the various composite particle synthesis have been proposed.

2002-08-01

475

Synthesis and characterization of Al_2O_3/ZrO_2, Al_2O_3/TiO_2 and Al_2O_3/ZrO_2/TiO_2 ceramic composite particles prepared by ultrasonic spray pyrolysis  

International Nuclear Information System (INIS)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the various composite particle synthesis have been proposed.

2002-08-01

476

Study on a recovery of rare earth oxides from a LiCl-KCl-RECl3 system  

British Library Electronic Table of Contents (United Kingdom)

Radioactive rare earth chlorides in waste LiCl-KCl molten salts have to be separated as a stable form to minimize waste volume and to achieve stable solidification. In this work, thermal behavior of rare earth chlorides (CeCl3, GdCl3, NdCl3, PrCl3) was investigated in an oxygen condition to recover rare earth oxides from a LiCl-KCl-RECl3 system. The rare earth chlorides in the LiCl-KCl molten salts were smoothly converted to an oxychloride form at a higher temperature than 650degreeC, except for CeCl3. CeCl3 was totally converted to an oxide from at a higher temperature than 450degreeC. The rare earth oxychlorides (GdOCl, NdOCl, PrOCl) were effectively converted to oxide forms at a higher temperature than 1100degreeC. It was confirmed that rare earth oxides can be recovered from a LiCl-KCl...

2011-01-01

477

Study of the carbon material / electrolyte interface; Etude de l`interface materiau carbone / electrolyte  

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is the comparative study of the properties of the natural graphite/liquid organic electrolyte interface by impedance spectroscopy with respect to different lithium salts (LiX with X = ClO{sub 4}{sup -}, BF{sub 4}{sup -}, CF{sub 3}SO{sub 3}{sup -}, N(CF{sub 3}SO{sub 2}){sub 2}{sup -}, PF{sub 6}{sup -}). The evolution of the interface properties during the first electrochemical reduction suggests different mechanisms of formation of passivation films. A more stable, thin and homogenous film seems to develop when the LiN(CF{sub 3}SO{sub 2}){sub 2} or LiPF{sub 6} lithium salts are used. The chemical diffusion coefficient of lithium in graphite has been determined by impedance spectroscopy. (J.S.) 16 refs.

1996-12-31

478

Steric Effects in Ionic Pairing and Polyelectrolyte Interdiffusion within Multilayered Films: A Neutron Reflectometry Study  

Energy Technology Data Exchange (ETDEWEB)

Using a series of polycations synthesized by atom transfer radical polymerization (ATRP), we investigate the effects of the polymer charge density and hydrophobicity on salt-induced interdiffusion of polymer layers within polyelectrolyte multilayer (PEM) films. Polycations with two distinct hydrophobicities and various quaternization degrees (QPDMA and QPDEA) were derived from parent polymers of matched molecular weights poly(2-(dimethylamino)ethyl methacrylate) (PDMA) and poly(2-(diethylamino)ethyl methacrylate) (PDEA) by quaternization with either methyl or ethyl sulfate. Multilayers of these polycations with polystyrene sulfonate (PSS) were assembled in low-salt conditions, and annealed in NaCl solutions to induce layer intermixing. As revealed by neutron reflectometry (NR), polycations with lower charge density resulted in a faster decay of film structure with distance from the substrate. Interestingly, when comparing polymer mobility in ...

2011-01-01

479

Separation and recovery method for depleted uranium from spent fuel  

Energy Technology Data Exchange (ETDEWEB)

Spent oxide fuels are reduced in a molten salt of CaCl[sub 2]-CaF[sub 2] to convert them into metals, then melted in an Fe-U bath disposed in an electrolytic refining vessel and brought into contact with molten Mg, to extract transuranium elements and rare earth elements contained in the Fe-U bath as metals in the molten Mg. Then molten Mg is removed and the residue is brought into contact with KCl-LiCl molten salt and electrolyzed using the Fe-U as an anode. Then, uranium is recovered by deposition on an iron cathode disposed in chloride electrolytes of the electrolytic refining vessel. Uranium and transuranium elements can be thus separated and, for example, depleted uranium for use in blanket fuels can be recovered easily. This can greatly reduce the temporary storage amount of depleted uranium, to eliminate requirement for a large-scaled facility used exclusively for storing uranium and long time management for uranium. (T.M.).

1993-07-30

480

Separation and recovery method for depleted uranium from spent fuel  

International Nuclear Information System (INIS)

Spent oxide fuels are reduced in a molten salt of CaCl_2-CaF_2 to convert them into metals, then melted in an Fe-U bath disposed in an electrolytic refining vessel and brought into contact with molten Mg, to extract transuranium elements and rare earth elements contained in the Fe-U bath as metals in the molten Mg. Then molten Mg is removed and the residue is brought into contact with KCl-LiCl molten salt and electrolyzed using the Fe-U as an anode. Then, uranium is recovered by deposition on an iron cathode disposed in chloride electrolytes of the electrolytic refining vessel. Uranium and transuranium elements can be thus separated and, for example, depleted uranium for use in blanket fuels can be recovered easily. This can greatly reduce the temporary storage amount of depleted uranium, to eliminate requirement for a large-scaled facility used exclusively for storing uranium and long time management for uranium. (T.M.).

1992-01-14

481

Radiation-induced reduction of ditetrazolium salt in aqueous solutions  

Energy Technology Data Exchange (ETDEWEB)

Color formation in aqueous solutions of the ditetrazolium salt blue tetrazolium (BT{sup 2+}) in the absence or presence of oxygen is a complex radiation chemical reaction. The final stable product is the poorly soluble diformazan violet to blue pigment having a broad spectral absorption band ({lambda}{sub max}=552 nm). The reaction of BT{sup 2+} with the hydrated electron proceeds by rapid reduction of BT{sup 2+} followed by protonation at the nitrogen closest to the unsubstituted phenyl group, via the two intermediate tetrazolinyl radicals shared by the ditetrazole ring nitrogens. The effect of solution pH, N{sub 2}O saturation, and the presence of the reducing agent dextrose are examined. The system serves as a radiochromic sensor and a dosimeter of ionizing radiations. Solutions of 5 mmol l{sup -1} BT{sup 2+} at pH 7.3 serve as dosimeters over an absorbed-dose range of approximately 0.2-6 kGy (dearated, with a range of 1-8 mmol l{sup -1} dextrose) and of about ...

2002-04-01

482

Pyrochemical Processing for Low-Level Waste Production in PEACER  

Science.gov (United States)

A pyrochemical partitioning process has been conceptually designed so that the transmutation of spent LWR fuels in PEACER can produce mainly low-level waste (Class C waste) for near-surface burial. Chloride salt technology developed for IFR has been employed as the baseline. Electrorefining, reductive extraction and salt recycling steps are used to construct overall flowsheet in order to support PEACER operation. The decontamination factor for transuranic elements was estimated based on both thermodynamic models and reported experimental data. It is expected that overall decontamination factor can be as high as 10{sup 5} for transuranic elements. Final wastes from pyrochemical processing for PEACER are noble metals, alkaline earth metal, and lanthanides. The final wastes are stabilized by mixing with zeolite and glass-frits such that concentration limit for class C waste can be met. The volume of Class C waste is estimated to be small enough to ...

2002-07-01

483

Pyrochemical Processing for Low-Level Waste Production in PEACER  

International Nuclear Information System (INIS)

A pyrochemical partitioning process has been conceptually designed so that the transmutation of spent LWR fuels in PEACER can produce mainly low-level waste (Class C waste) for near-surface burial. Chloride salt technology developed for IFR has been employed as the baseline. Electrorefining, reductive extraction and salt recycling steps are used to construct overall flowsheet in order to support PEACER operation. The decontamination factor for transuranic elements was estimated based on both thermodynamic models and reported experimental data. It is expected that overall decontamination factor can be as high as 10"5 for transuranic elements. Final wastes from pyrochemical processing for PEACER are noble metals, alkaline earth metal, and lanthanides. The final wastes are stabilized by mixing with zeolite and glass-frits such that concentration limit for class C waste can be met. The volume of Class C waste is estimated to be small enough to make ...

2002-06-09

484

Layer-by-layer self-assembly of polyimide precursor/layered double hydroxide ultrathin films  

International Nuclear Information System (INIS)

The layer-by-layer (LBL) self-assembly has been extensively used as a simple and effective method for the preparation of polyelectrolyte multilayer films. In this work, we utilized this unique method to prepare polyimide precursor/layered double hydroxide (LDH) ultrathin films. Well-crystallized Co-Al-CO_3 LDH and subsequent anion exchanged Co-Al-NO_3 LDH were prepared and characterized by scanning electron microscopy and X-ray diffraction (XRD). By vigorous shaking of the as-prepared Co-Al-NO_3 LDH, positively charged and exfoliated LDH nanosheets were obtained. Atomic force microscopy and XRD investigations indicated the delamination of LDH nanosheets. The precursor of polyimide, poly(amic acid) tertiary amine salt (PAS) was prepared by the polycondensation of dianhydride and diamine, and subsequent amine salt formation. By using the LBL method, heterogeneous ultrathin films of PAS and LDH were prepared. The formation of the ordered ...

2010-09-30

485

Ion transport properties of lithium ionic liquids and their ion gels  

International Nuclear Information System (INIS)

A new series of lithium ionic liquids were prepared by introducing of two electron-withdrawing trifluoroacetyl groups in borate salts containing two methoxy-oligo(ethylene oxide) groups in the structures. Successive substitution reactions of oligo-ethylene glycol monomethyl ether and trifluroacetic acid from LiBH_4 yielded the lithium salts, which were clear and colorless liquids at room temperature. The fundamental physicochemical properties, such as density, thermal property, viscosity, ionic conductivity, self-diffusion coefficients, and electrochemical stability, were measured. The lithium ionic liquids had self-dissociation ability and conducted ions even in the absence of organic solvents. New polymer electrolytes, named 'ion gels', were prepared by radical cross-linking reactions of a poly(ethylene oxide-co-propylene oxide)tri-acrylate macromonomer in the presence the lithium ionic liquid. An increase in the glass transition temperatures ...

2005-06-30

486

Inhibition of corrosion resistant alloys in hot hydrochloric acid solutions  

Energy Technology Data Exchange (ETDEWEB)

Weight loss measurements were performed in 20% and 28% hydrochloric acid at 90/sup 0/C on carbon steel, 22Cr5Ni duplex stainless steel, and two superaustenitic steels - 27Cr31Ni3Mo and 19Cr25Ni4Mo -, in presence of organic substances used singly or mixed. The organic substances examined were quaternary ammonium salts (1-4-pyridyl)-pyridinium chloride hydrochloride, dodecylpyridiniumchloride, benzyldimethylstearylammonium chloride, and dodecyltrimethylammonium bromide), alkynols (1-octyn-3-ol, propargyl alcohol) and trans-cinnamaldehyde. The synergistic effect of potassium iodide on the inhibitive efficiency of the organic substances was studied. The variations of corrosion rate during the test time (normally six hours) were recorded by means of polarization resistance measurements. Polarization curves were also recorded. The results showed that the corrosion rates of the four steels examined can be reduced to less than 1 mg/cm/sup -2/ . h/sup -1/ using ternary ...

1988-12-01

487

Histamine Molecule and Dianion Oxalate are Efficient Blocks for Building 2D Supramolecular Networks  

British Library Electronic Table of Contents (United Kingdom)

One salt and two Cu(II) complexes (H2hsm)(ox), 1, [Cu(hsm)(ox)], 2, and [Cu(hsm)(ox)H2O], 3, have been synthesized and X-ray characterized (hsm is histamine and ox2? is the oxalate dianion). Starting from the prochiral tetracoordinated complex 2, pentacoordinated complex 3 crystallizes as a racemic mixture of the enantiomeric ? and ? isomers, in space group P21/c. In all cases, the side chain of the hsm group is gauche, allowing the formation of strong hydrogen bonds in the salt 1, and to chelate the metal center in complexes 2 and 3. The combination hsm/ox seems to favor the formation of 2D supramolecular structures (planes or wavy planes), through efficient networks of N?H???O hydrogen bonds. Cell parameters: 1, P21/c, a?=?6.260 (2) ?, b?=?11.500 (4) ?, c?=?12.525 (4) ?, ??=?104.047 (17)...

2011-01-01

488

Highly reliable contacts for lead-salt diode lasers  

Energy Technology Data Exchange (ETDEWEB)

In order to improve the long term reliability of lead-salt diode lasers, ohmic contacts of multilayer, thin-film structures consisting of In plus Au, Pt, Ni, and Pd have been studied. Diode lasers of PbSnTe fabricated with a variety of contacts were tested during room-temperature storage and during accelerated aging tests. The results show that contact reliablility can be improved when multiple overlapping films are used. After 4500 h of baking at 60 /sup 0/C, lasers with In-Au-Pd-Au contacts on both sides showed the least resistance increase (10%). For lasers with In-Au-Pt-Au contacts, 1 h of baking at 60 /sup 0/C is equivalent to 2 d storage at room temperature. Extrapolating these results, a 70% increase in contact resistance is expected for this type of laser after 9000 d of storage at room temperture. Our data also suggests that a smaller increase in contact resistance can be expected for lasers fabricated with In-Au-Ni-Au and In-Au-Pd-Au contacts.

1981-02-01

489

Electrochemical behavior of zirconium in the LiCl-KCl molten salt at Mo electrode  

British Library Electronic Table of Contents (United Kingdom)

The electroreduction process of Zr(IV) was studied at molybdenum electrode in LiCl-KCl-K2ZrF6 molten salt. The transient electrochemical techniques, such as cyclic voltammetry and chronopotenimetry were used. The experimental results showed that the electrochemical reduction of Zr(II)/Zr and Zr(IV)/Zr(II) were both diffusion-controlled process. In the 773-973K range, the diffusion coefficients of Zr(ii) and Zr(IV) were determined: DZr(II)=0.15567exp{-69.65x10^3RT(K)}cm^2/s, DZr(IV)=1.09x10^-^4exp{-44.39x10^3RT(K)}cm^2/s. The activation energy values for the diffusion process were 69.65kJ/mol and 44.39kJ/mol, respectively.

2011-01-01

490

Elastic modeling and steep dips: unraveling the reflected wavefield  

Energy Technology Data Exchange (ETDEWEB)

As part of a larger elastic numerical modeling project, we have been investigating how energy reflected from steeply dipping interfaces is recorded using typical multicomponent acquisition geometries. Specifically, we have been interpreting how rcflection events from the flanks of salt dome structures are distributed on 3C and 4C phones for vertical seismic profiles (VSPs) and ocean bottom seismic (OBS) or land surface surveys. The ultimate goal of this investigation is to improve the structural imaging of steeply dipping interfaces and eventually to evaluate the usc of the recorded elastic wavefield for fluid description near these interfaces. In the current work, we focus on a common assumption used when processing converted wave reflection seismic data that most PP energy is recorded on the vertical geophone and/or the hydrophone and that most PS energy is recorded on the horizontal geophones. This is a useful assumption when it is valid, because it eliminates ...

2003-01-01

491

Development of pyrometallurgical partitioning of transuranium elements from high-level liquid waste. Improvement to pyrometallurgical partitioning process and process demonstration  

Energy Technology Data Exchange (ETDEWEB)

The partitioning of transuranium elements (TRUs) from high-level liquid waste (HLLW) through the use of pyrometallurgical technology has been underway since 1986, for the purpose of the improving the safety and public acceptance of the disposal of high-level vitrified waste. Prior to the pyrometallurgical partitioning process, the alkali metals can be separated at the denitration process for oxide conversion of HLLW, chlorination in a chloride salt bath can be used to effectively convert oxides to chlorides, and evaporated chlorides can be captured with high efficiency in another adopted chloride salt bath. The higher separation factors between actinides and rare earths are obtained in a LiCl-KCl/Bi system than in a LiCl-KCl/Cd system. Based on the results, we propose a practical process flow for partitioning TRUs from HLLW by pyrometallurgical technology. This process was demonstrated successfully using simulated purex waste. Each element of ...

1998-10-01

492

Development of a process for the disposal of evaporation residues from NPP by precipitation/flocculation and solidification of the precipitation products. Final report  

International Nuclear Information System (INIS)

To reduce the volume of radioactive wastes after evaporation, activity carriers can be separated from the inactive salt load. Boric acid separation from PWR concentrates was considered a preliminary stage for nuclide precipitation. In connection with the precipitation process, the reaction conditions for boric acid separation were determined by bench-scale experiments. After evaluating the known purification processes, crystallization was suggested as a practicable method. After inactive bench-scale experiments, mixed crystal formation with iron hexacyanoferrate for Cs removal was chosen. The disturbing effect of the complexing agents was neutralized by a pre-dose of iron-III-salts. By specifying the precipitation conditions, for Cs-134 an activity separation from 3,0 E + 06 Bg/l to 1,9 E + 02 Bg/l, and for Cs-137 from 5,9 E + 06 Bg/l to 1,2 E + 02 Bg/l was achieved. Accordingly, the decontamination factor for Cs-134 was 16000, and for Cs-137 ...

493

Alteration of alpha 1 Na+,K(+)-ATPase "8"6Rb"+ influx by a single amino acid substitution  

International Nuclear Information System (INIS)

The sodium- and potassium-dependent adenosine triphosphatase (Na+,K(+)-ATPase) maintains the transmembrane Na+ gradient to which is coupled all active cellular transport systems. The R and S alleles of the gene encoding the Na+,K(+)-ATPase alpha 1 subunit isoform were identified in Dahl salt-resistant (DR) and Dahl salt-sensitive (DS) rats, respectively. Characterization of the S allele-specific Na+,K(+)-ATPase alpha 1 complementary DNA identified a leucine substitution of glutamine at position 276. This mutation alters the hydropathy profile of a region in proximity to T3(Na), the trypsin-sensitive site that is only detected in the presence of Na+. This mutation causes a decrease in the rubidium-86 influx of S allele-specific sodium pumps, thus marking a domain in the Na+,K(+)-ATPase alpha subunit important for K+ transport, and supporting the hypothesis of a putative role of these pumps in hypertension.

494

A novel high temperature stable lithium salt (Li{sub 2}B{sub 12}F{sub 12}) for lithium ion batteries  

Energy Technology Data Exchange (ETDEWEB)

Basic properties and battery performances of the novel high temperature stable lithium salt (Li{sub 2}B{sub 12}F{sub 12}, Dilithium Dodecafluorododecaborate; Li{sub 2}DFB) were studied using a Mn-based cathode and anode composed of a hard carbon and graphite mixture. The effect of co-solvents (mainly linear carbonate in electrolyte formulation of PC/EC/co-solvent (5/30/65 vol% mixture)) on conductivity, viscosity, charge-discharge capacities, rate performance, temperature performance, cycle life and storage life at 60 C was investigated. Conductivity of Li{sub 2}DFB electrolyte increased with reducing its viscosity by changing co-solvent and increasing the volume of the higher dielectric solvent. Li{sub 2}DFB electrolytes showed comparable discharge capacity and columbic efficiency against LiPF{sub 6} electrolyte. Li{sub 2}DFB electrolytes improved the storage life and cycle life of a Mn-based cell at 60 C. (author)

2009-09-05

495

A dip-dependent divergence correction  

Energy Technology Data Exchange (ETDEWEB)

A divergence correction is conventionally applied to zero-offset data in an effort to preserved amplitude information. The conventional divergence correction compensates for the geometrical spreading of a point source in a horizontally layered medium where velocity varies with depth only. The dip-dependent divergence correction extends the conventional correction for improved amplitude processing of dipping beds. The dip-dependent divergence correction is computed by dynamic ray tracing, and applied to stacked data using a dip decomposition technique. This correction decreases amplitudes relative to the conventional correction for steep dips and late times. In a data example from the Gulf of Mexico, the conventional correction over- amplified the reflection off a salt dome flank by a factor of 1.6. High amplitudes near salt flanks are also associated with the presence of hydrocarbons. Applying the dip-dependent divergence correction ensures ...

1992-01-01

496

A dip-dependent divergence correction  

Energy Technology Data Exchange (ETDEWEB)

A divergence correction is conventionally applied to zero-offset data in an effort to preserved amplitude information. The conventional divergence correction compensates for the geometrical spreading of a point source in a horizontally layered medium where velocity varies with depth only. The dip-dependent divergence correction extends the conventional correction for improved amplitude processing of dipping beds. The dip-dependent divergence correction is computed by dynamic ray tracing, and applied to stacked data using a dip decomposition technique. This correction decreases amplitudes relative to the conventional correction for steep dips and late times. In a data example from the Gulf of Mexico, the conventional correction over- amplified the reflection off a salt dome flank by a factor of 1.6. High amplitudes near salt flanks are also associated with the presence of hydrocarbons. Applying the dip-dependent divergence correction ensures ...

1992-07-01

497

Phytic acid doped nanoparticles for green anticorrosion coatings  

British Library Electronic Table of Contents (United Kingdom)

In this paper, an environmentally friendly metal corrosion inhibitor, phytic acid, was assembled into the walls of silica nanoparticles via layer-by-layer self-assembly technique (LbL) with poly(allylamine hydrochloride). Such functionalized nanoparticles were uniformly distributed into sol-gel films for metal anticorrosion. The films showed very pronounced and lasting protective efficiency in concentrated salt aqueous solutions as indicated by electrochemical impedance spectroscopy (EIS) measurement. These results may provide a new route for the preparation of environment-friendly anticorrosion coatings.

2010-01-01

498

Emulsans. [Acinetobacter sp. ATCC 31012  

Energy Technology Data Exchange (ETDEWEB)

The production and uses are described for extracellular microbial polysaccharides (generically called emulsans) and for a new class of extracellular microbial protein-associated lipopolysaccharides (collectively called alpha-emulsans) produced by Acinetobacter Sp. ATCC 31012, its mutants or recombinants. Also included are the deproteinized lipopolysaccharides (collectively called apoemulsans) obtained from such emulsans, as well as to the divalent metal, ammonium, and quaternary ammonium salts of such emulsans and apoemulsans. The materials can be used (1) in cleaning oil-contaminated vessels used to transport or store crude oil or petroleum fractions in such a manner that the residual oil may be recovered for fuel value or for refining and (2) in enhanced oil recovery.

1983-07-05

499

Design, synthesis and evaluation of redox radiopharmaceuticals: a potential new approach for the development of brain imaging agents  

International Nuclear Information System (INIS)

The goals of this paper are to describe the fabrication and complete evaluation of a dihydropyridine <- -> pyridinium salt type redox system for the delivery of radioiodinated agents to the brain. Tissue distribution studies of "1"2"5I-labeled 4-iodoaniline and the redox agents were performed in rats. ["1"2"5I]Iodoaniline initially showed moderate brain uptake with subsequent release of the radioactivity from the brain. ["1"2"5I]Iodoaniline, however, when coupled to a dihydropyridine carrier showed significantly higher uptake and retention in the brain. (author).