Sample records for chromium 59

  1. Chromium

    ... health risks of too much chromium? Chromium and medication interactions Supplemental sources of chromium Chromium and Healthful Diets References Disclaimer What foods provide chromium? Chromium is widely distributed in the ...

  2. Microstructural characterization of 5-9% chromium reduced-activation steels

    The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M23C6 and small spherical MC. The two lower-chromium steels contained blocky M7C3 and small needle-shaped carbonitrides in addition to M23C6. AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations

  3. Microstructural characterization of 5-9% chromium reduced-activation steels

    Jayaram, R. [Univ. of Pittsburgh, PA (United States); Klueh, R.L. [Oak Ridge National Lab., TN (United States)


    The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M{sub 23}C{sub 6} and small spherical MC. The two lower-chromium steels contained blocky M{sub 7}C{sub 3} and small needle-shaped carbonitrides in addition to M{sub 23}C{sub 6}. AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations.

  4. Effect of chromium, tungsten, tantalum, and boron on mechanical properties of 5-9Cr-WVTaB steels

    The Cr-W-V-Ta reduced-activation ferritic/martensitic steels use tungsten and tantalum as substitutes for molybdenum and niobium in the Cr-Mo-V-Nb steels that the reduced-activation steels replaced as candidate materials for fusion applications. Studies were made to determine the effect of W, Ta, and Cr composition on the tensile and Charpy properties of the Cr-W-V-Ta; steels with 5%, 7%, and 9% Cr with 2% or 3% W and 0%, 0.05%, or 0.10% Ta were examined. Boron has a long history of use in steels to improve properties, and the effect of boron was also examined. Regardless of the chromium concentration, the steels with 2% W and 0.05-0.1% Ta generally had a better combination of tensile and Charpy properties than steels with 3% W. Boron had a negative effect on properties for the 5% and 7% Cr steels, but had a positive effect on the 9% Cr steel. When the 5, 7, and 9Cr steels containing 2% W and 0.05% Ta were compared, the tensile and Charpy properties of the 5 and 9Cr steels were better than those of the 7Cr steel, and overall, the properties of the 5Cr steel were better than those of the 9Cr steel. Such information will be useful if the properties of the reduced-activation steels are to be optimized

  5. Heterogeneous chromium catalysts


    The present invention relates to a heterogeneous chromium catalyst system for the polymerisation of ethylene and/or alpha olefins prepared by the steps of: (a) providing a silica-containing support, (b) treating the silica-containing support with a chromium compound to form a chromium-based silica-containing support, (c) activating the chromium-based silica-containing support, (d) chemically reducing the activated chromium-based silica-containing support to produce a precursor catalyst, (e) r...

  6. Hexavalent Chromium Workshop

    EPA is developing an updated IRIS assessment of hexavalent chromium. This assessment will evaluate the potential health effects of hexavalent chromium from oral and inhalation exposures. An important component of determining the cancer causing potential of ingested hexavalent chr...

  7. Chromium and Genomic Stability

    Wise, Sandra S.; Wise, John Pierce


    Many metals serve as micronutrients which protect against genomic instability. Chromium is most abundant in its trivalent and hexavalent forms. Trivalent chromium has historically been considered an essential element, though recent data indicate that while it can have pharmacological effects and value, it is not essential. There are no data indicating that trivalent chromium promotes genomic stability and, instead may promote genomic instability. Hexavalent chromium is widely accepted as high...

  8. Serum chromium levels in gestational diabetes mellitus

    P G Sundararaman


    Full Text Available Objective: To measure serum chromium level in women with gestational diabetes mellitus (GDM from Chennai, South India. Materials and Methods: Thirty women with gestational diabetes, 60 age matched controls. Inclusion criteria: Gestational age 22-28 weeks, age group 20-35 years. Exclusion Criteria: Gestational age beyond 28 weeks, malnutrition or presence of infection. Serum chromium was measured using inductive couple plasma emission spectrometer. Results: Serum chromium levels of women with GDM, 1.59+/-0.02 ng/ml (range: 0.16-4.0 ng/ml were lower than in controls (4.58+/-0.62 ng/ml; range 0.82-5.33 ng/ml (P < 0.001. However, there were no significant differences among cases and controls when subdivided by parity. Conclusions: Women with GDM from a South Indian city had lower levels of serum chromium compared to pregnant women without GDM. Studies may be done whether chromium supplementation is useful in this group of women.

  9. Oxidation of chromium telluride

    The authors study the interaction between chromium telluride and oxygen at elevated temperatures in view of its application in semiconductor technology. Thermodynamic analysis of the oxidation process and experimental data showed that the alloys of chromium telluride suffer oxidation in the presence of even traces of oxygen in a gaseous medium. Chromium telluride oxidation is a complex process that gives rise to various oxides and is accompanied by partial sublimation

  10. Oxidation of chromium telluride

    Pakhomovskaya, N.S.; Iorga, E.V.; Sheveleva, T.F.; Solov' eva, A.E.


    The authors study the interaction between chromium telluride and oxygen at elevated temperatures in view of its application in semiconductor technology. Thermodynamic analysis of the oxidation process and experimental data showed that the alloys of chromium telluride suffer oxidation in the presence of even traces of oxygen in a gaseous medium. Chromium telluride oxidation is a complex process that gives rise to various oxides and is accompanied by partial sublimation.

  11. Hair chromium concentration and chromium excretion in tannery workers.

    Saner, G; Yüzbasiyan, V; Cigdem, S


    Hair and urine samples were collected from 34 male tannery workers and from 12 normal adults. Eighteen of the workers dealt directly with chromium and the remaining 16 (controls) worked in the offices and kitchen of the same factory. All were found to be clinically healthy. Chromium was determined by flameless atomic absorption spectroscopy. When compared with normal adult values, urinary chromium concentration, Cr/Creatinine ratio, daily chromium excretion, and hair chromium, concentrations ...

  12. High-Purity Chromium Targets

    Rudoy, A.; Milman, Yu.; Korzhova, N.


    A procedure for producing large-scale chromium ingots by means of induction-arc melting was developed. From the high-purity, low-alloyed chromium ingots obtained, chromium targets were produced by of thermoplastic treatment techniques. The method of electron-beam evaporation of high-purity chromium was also used for production of targets.

  13. Microstructural characterisation of chromium slags

    Burja, J.; F. Tehovnik; Vode, F.; Arh, B.


    In this chromium slags that form during melting of chromium alloyed steels are examined. During melting and oxidation of these steel grades a considerable amount of chromium is lost, and gained back with slag reduction. Laboratory experiments were performed to study the mechanism of chromium oxide reduction by silicon. Slags chemistry and phase composition have a strong effect on the steelmaking process. Phase analysis revealed two types of chromium oxides, calcium chromites and chromite spin...

  14. Substoichiometric extraction of chromium

    Substoichiometric extraction of chromium with tetraphenylarsonium chloride (TPACl), tri-n-octylamine (TNOA), diethylammonium diethyldithiocarbamate (DDDC) and ammonium pyrrolidinedithiocarbamate (APDC) was examined in detail. Chromium can be extracted substoichiometrically in a pH range, which is 1.1-2.6 for the TPACl compound, 0.6-2.3 for the TNOA compound, 5.1-6.4 for the DDDC chelate and 3.9-4.9 for the APDC chelate. Chromium in high-purity calcium carbonate, Orchard Leaves (NBS SRM-1571) and Brewers Yeast (NBS SRM-1569) was determined by neutron activation analysis combined with substoichiometric extraction by DDDC and APDC. The values of 2.0+-0.02 ppm and 2.6+-0.2 ppm were obtained for Brewers Yeast and Orchard Leaves, respectively. These values were in good agreement with those reported by NBS. The reaction mechanism and the reaction ratio between hexavalent chromium and dithiocarbamate are also discussed. (author)

  15. Chromium in diet

    ... Chromium deficiency may be seen as impaired glucose tolerance. It occurs in older people with type 2 ... PhD, and the A.D.A.M. Editorial team. Related MedlinePlus Health Topics Minerals Browse the Encyclopedia ...

  16. The carcinogenicity of chromium

    Norseth, Tor


    The carcinogenicity of chromium compounds is reviewed with specific attention to the gaps in knowledge for risk estimation and research needs. The most important problems at present are whether trivalent chromium compounds cause cancer, and whether there is a difference in cancer causing effects between the soluble and the slightly soluble hexavalent compounds in the practical exposure situation. Dose estimates for risk estimation based on epidemiological investigations are also lacking. Pres...

  17. STS-59 crew insignia


    The STS-59 insignia is dominated by Earth, reflecting the focus of the first Space Radar Laboratory (SRL-1) mission upon our planet's surface and atmosphere. The golden symbol of the astronaut corps emblem sweeps over Earth's surface from the Space Shuttle Endeavour, representing the operation of the SIR-C/Synthetic Aperture Radar (X-SAR) and the Measurement of Air Pollution from Space (MAPS) sensors. The astronaut emblem also signals the importance of the human element in space exploration and in the study of our planet. The star field visible below Earth represents the many talents and skill of the international SRL-1 team.

  18. STS-59 Insignia


    The STS-59 insignia is dominated by Earth, reflecting the focus of the first Space Radar Laboratory (SRL-1) mission upon our planet's surface and atmosphere. The golden symbol of the astronaut corps emblem sweeps over Earth's surface from the Space Shuttle Endeavour, representing the operation of the SIR-C/Synthetic Aperture Radar (X-SAR) and the Measurement of Air Pollution from Space (MAPS) sensors. The astronaut emblem also signals the importance of the human element in space exploration and in the study of our planet. The star field visible below Earth represents the many talents and skill of the international SRL-1 team.

  19. Obtaining decorative chromium plating from trivalent chromium solutions

    Óscar Javier Suárez García


    The present work was aimed at a qualitative evaluation, in the laboratory, of different alternatives for assembling and operating a trivalent chromium bath for decorative chromium plating. Different chromium concentration solutions and different complexing agents were used. The initial result of this analysis was that chloride, formate and acetate solutions produced the best results. Solution preparation conditions were evaluated: temperature, chromium III complex formation time and also ...

  20. The analytical biochemistry of chromium.

    Katz, S A


    The essentiality and carcinogenicity of chromium depend on its chemical form. Oxidation state and solubility are particularly important in determining the biological effects of chromium compounds. For this reason, total chromium measurements are of little value in assessing its nutritional benefits or its toxicological hazards. Aqueous sodium carbonate-sodium hydroxide solutions have been successfully used for extracting hexavalent chromium from a variety of environmental and biological matri...

  1. Chromium in potatoes

    Chromium concentration in potatoes was determined, and tubes were labeled either intrinsically or extrinsically with radioactive chromate (51Cr). A labeled chromium complex was isolated from preparations of raw, baked, or fried potatoes and chromatographed on gel permeation media. Potato pulp and peel contained 1.63 and 2.70 μg of Cr/g tissue, respectively. There was no correlation between the two, nor did they respond similarly to changes of variety or locations. No significant differences were apparent in relative migration of the isolated complexes except between raw and cooked extrinsically labeled preparations

  2. Chromium and aging

    Aging is associated with increased blood glucose, insulin, blood lipids, and fat mass, and decreased lean body mass leading to increased incidences of diabetes and cardiovascular diseases. Improved chromium nutrition is associated with improvements in all of these variables. Insulin sensitivity de...

  3. Studies of chromium gettering

    Preliminary results have shown that hydrogen pumping by chromium is a surface effect. Unlike with titanium, the getter material used in many present day tokamaks, there is no significant diffusion into the bulk. Additional experiments have been carried out to measure the basic characteristics of chromium films for gases of interest in tokamak research. These gases include deuterium, oxygen and nitrogen. A vacuum system is described which allowed precise control of the test gas, a constant wall temperature and determination of the projected getter surface area. A quadrupole mass spectrometer, rather than simply a total pressure gauge, was utilized to measure the partial pressure of the test gas as well as the residual gas composition in the system. A quartz crystal monitor was used to measure film thickness. Pumping speeds and sticking coefficients are given as a function of surface coverage for each test gas. A comparison will be made with titanium films deposited in the same vacuum system and under similar conditions

  4. Catalytic Spectrophotometric Determination of Chromium

    STOYANOVA, Angelina Miltcheva


    The catalytic effect of chromium(III) and chromium(VI) on the oxidation of sulfanilic acid by hydrogen peroxide was studied. The reaction was followed spectrophotometrically by measuring the absorbance of the reaction product at 360 nm. Under the optimum conditions 2 calibration graphs (for chromium(III) up to 100 ng mL-1, and for chromium(VI) up to 200 ng mL-1) were obtained, using the ``fixed time'' method with detection limits of 4.9 ng mL-1 and 3.8 ng mL-1, respectively...


    Suboptimal intakes of the essential nutrient, chromium, are characterized by elevated blood glucose, insulin resistance, obesity, hypertriglyceridemia, and low HDL. These are also signs and symptoms of the metabolic syndrome. Improvements due to increased intake of chromium are related to the degr...

  6. Groundwater contaminant by hexavalent chromium

    Parsons, C. [Univ. of Texas, Austin, TX (United States)


    Oxidation of trivalent chromium to hexavalent chromium has been investigated as a function of total manganese in soils as well as various incubation conditions. Chromium and manganese contents were analyzed by atomic absorption (graphite furnace and flame emission respectively) following acid digestion. Total hexavalent chromium generation capacity was determined by addition of 0.001 M CrCL3, incubation, and analysis by s-diphenyl carbazide. Samples were then leached with CaSO{sub 4} and MgSO{sub 4} and incubated in various environments (oven, freeze-drier, field moist, ultrafreeze) to test for geogenic generation of Cr(IV). The degree of geogenic generation of hexavalent chromium was compared with total Mn and Cr content as well as hexavalent generational capacity.

  7. Role of paramagnetic chromium in chromium(VI)-induced damage in cultured mammalian cells.

    Sugiyama, M


    Chromium(VI) compounds are known to be potent toxic and carcinogenic agents. Because chromium(VI) is easily taken up by cells and is subsequently reduced to chromium(III), the formation of paramagnetic chromium such as chromium(V) and chromium(III) is believed to play a role in the adverse biological effects of chromium(VI) compounds. The present report, uses electron spin resonance (ESR) spectroscopy; the importance of the role of paramagnetic chromium in chromium(VI)-induced damage in intac...

  8. The determination of chromium-50 in human blood and its utilization for blood volume measurements

    Possible relationships between insufficient blood volume increases during pregnancy and infant mortality could be established with an adequate measurement procedure. An accurate and precise technique for blood volume measurements has been found in the isotope dilution technique using chromium-51 as a label for red blood cells. However, in a study involving pregnant women, only stable isotopes can be used for labeling. Stable chromium-50 can be determined in total blood samples before and after dilution experiments by neutron activation analysis (NAA) or mass spectrometry. However, both techniques may be affected by insufficient sensitivity and contamination problems at the inherently low natural chromium concentrations to be measured in the blood. NAA procedures involving irradiations with highly thermalized neutrons at a fluence rate of 2x1013 n/cm2xs and low background gamma spectrometry are applied to the analysis of total blood. Natural levels of chromium-50 in human and animal blood have been found to be <0.1 ng/mL; i.e., total chromium levels of <3 ng/mL. Based on the NAA procedure, a new approach to the blood volume measurement via chromium-50 isotope dilution has been developed which utilizes the ratio of the induced activities of chromium-51 to the iron-59 in three blood samples taken from each individual, namely blank, labeled and diluted labeled blood. (author)

  9. Fate and transport of chromium through soil

    Chromium chemistry relevant to the problem facing state of New Jersey (Usa) was examined. Transport of chromium through soil depends on its chemical forms. Transformation of chromium within bulk of soil depends on soil constituents, soil condition, such as pH, Eh and organic compounds applied onto soil or present in soil. Total chromium in soil can be determined. Speciation of chromium based on ionization, hydrolysis, complex formation, redox reactions and adsorption is predicted using MINIQ program

  10. Release of Chromium from Orthopaedic Arthroplasties

    Afolaranmi, G.A.; Tettey, J; Meek, R.M.D; Grant, M.H


    Many orthopaedic implants are composed of alloys containing chromium. Of particular relevance is the increasing number of Cobalt Chromium bearing arthroplasies being inserted into young patients with osteoarthritis. Such implants will release chromium ions. These patients will be exposed to the released chromium for over 50 years in some cases. The subsequent chromium ion metabolism and redistribution in fluid and tissue compartments is complex. In addition, the potential biological effects o...

  11. Chromium isotope variations

    D'Arcy, Joan Mary

    Chromium (Cr) stable isotopes are a useful tracer of changes in redox conditions because changes in its oxidation state are accompanied by an isotopic fractionation. For this reason the Cr isotope system is being developed as a potential tool for paleo-redox reconstruction. Dissolved Cr in seawater...... is incorporated into carbonates. Hence, ancient carbonates can potentially record the Cr isotopic composition (δ53Cr ‰) of seawater in the geological past. Reliable application and interpretation of this proxy requires a detailed knowledge about processes that fractionate Cr on the Earth’s surface......, and the quantification the Cr isotope composition of major Cr fluxes into and out of ocean. This thesis adds to the current knowledge of the Cr isotope system and is divided into two studies. The focus of the first study was to determine what processes control the Cr isotopic compositionof river...

  12. Chromium reduction in Pseudomonas putida.

    Ishibashi, Y.; Cervantes, C; Silver, S


    Reduction of hexavalent chromium (chromate) to less-toxic trivalent chromium was studied by using cell suspensions and cell-free supernatant fluids from Pseudomonas putida PRS2000. Chromate reductase activity was associated with soluble protein and not with the membrane fraction. The crude enzyme activity was heat labile and showed a Km of 40 microM CrO4(2-). Neither sulfate nor nitrate affected chromate reduction either in vitro or with intact cells.

  13. Chromium reduction in Pseudomonas putida.

    Ishibashi, Y; Cervantes, C; Silver, S


    Reduction of hexavalent chromium (chromate) to less-toxic trivalent chromium was studied by using cell suspensions and cell-free supernatant fluids from Pseudomonas putida PRS2000. Chromate reductase activity was associated with soluble protein and not with the membrane fraction. The crude enzyme activity was heat labile and showed a Km of 40 microM CrO4(2-). Neither sulfate nor nitrate affected chromate reduction either in vitro or with intact cells. PMID:2389940

  14. Hydrogen permeation through chromium

    Steady state and non-steady state measurements of hydrogen permeation through metallic chromium are reported. The experiments have been conducted by use of hydrogen and deuterium within a pressure range of 10-8 - 1 bar and temperatures between 600 - 8000C. Numerical values for the physical quantities permeability, diffusion constant and solubility could be derived. At an upstream pressure above around 10-3 bar classical Sieverts-low was found (permeation rate proportional √p) with activation energies Qsub(perm) = 65 kJoule/mole, Qsub(Diff) = 4-8 kJoule/mole, Qsub(Sol) = 57-61 kJoule/mole for the respective processes involved. The isotopic effect between H and D of the permeabilities could be represented by a factor of 1,5 independence on temperature. All non steady-state measurements could be approximated reasonably well by classical diffusion kinetics. Below up-stream pressures of approx.= 10-7 bar the kinetics was no longer diffusion controlled, the dependence on up-stream pressure changed from √p -> p, the activation energy for permetation increased to 127 kJoule/mole and the isotopic factor resulted in about 2-3. (orig.)

  15. Trivalent chromium sorption on alginate beads

    Araújo, M. Manuela; Teixeira, J.A.


    The applicability of trivalent chromium removal from aqueous solutions using calcium alginate beads was studied. The equilibrium isotherms were plotted at two temperatures. The relationship between the chromium sorbed and the calcium released was determined as well as the effect of alginate amount and initial pH on the equilibrium results. Chromium sorption kinetics were evaluated as a function of chromium initial concentration and temperature. Transport properties of trival...

  16. On texture formation of chromium electrodeposits

    Nielsen, Christian Bergenstof; Leisner, Peter; Horsewell, Andy


    The microstructure, texture and hardness of electrodeposited hard, direct current (DC) chromium and pulsed reversed chromium has been investigated. These investigations suggest that the growth and texture of hard chromium is controlled by inhibition processes and reactions. Further, it has been...

  17. Chromium Salen Mediated Alkene Epoxidation

    Petersen, Kaare Brandt; Norrby, Per-Ola; Daly, Adrian M.; Gilheany, Declan G.


    The mechanism of alkene epoxidation by chromium(v) oxo salen complexes has been studied by DFT and experimental methods. The reaction is compared to the closely related Mn-catalyzed process in an attempt to understand the dramatic difference in selectivity between the two systems. Overall, the......-spin surface. The low-spin addition of metal oxo species to an alkene leads to an intermediate which forms epoxide either with a barrier on the low-spin surface or without a barrier after spin inversion. Supporting evidence for this intermediate was obtained by using vinylcyclopropane traps. The chromium...

  18. Magnetic Moment of $^{59}$Cu


    Experiment IS358 uses the intense and pure beams of copper isotopes provided by the ISOLDE RILIS (resonance ionization laser ion source). The isotopes are implanted and oriented in the low temperature nuclear orientation set-up NICOLE. Magnetic moments are measured by $\\beta$-NMR. Copper (Z=29), with a single proton above the proton-magic nickel isotopes provides an ideal testground for precise shell model calculations of magnetic moments and their experimental verification. In the course of our experiments we already determined the magnetic moments of $^{67}$Ni, $^{67}$Cu, $^{68g}$Cu, $^{69}$Cu and $^{71}$Cu which provide important information on the magicity of the N=40 subshell closure. In 2001 we plan to conclude our systematic investigations by measuring the magnetic moment of the neutron-deficient isotope $^{59}$Cu. This will pave the way for a subsequent study of the magnetic moment of $^{57}$Cu with a complementary method.

  19. Activity determination of 59Fe

    Iron-59 was measured in three commercial and two custom-built liquid scintillation counters. The counting efficiencies were determined using CIEMAT/NIST efficiency tracing and the triple-to-double coincidence ratio (TDCR) method, respectively. The efficiency computation for the TDCR method was realized by means of the MICELLE2 program, applying a stochastic model for the computation of electron emission spectra. The program was extended to make calculations of spectra originating from complex decay schemes possible. In addition, a new parameterization of electron stopping powers for 10 commercial liquid scintillation cocktails was included in the software. The activities determined with the two methods were in very good agreement; the relative standard uncertainty of the combined result was found to be 0.16%. It was used to calibrate a 4π ionization chamber at PTB for future calibrations of this isotope which is used for investigations of iron metabolism. A standardized solution was submitted to the Bureau International des Poids et Mesures (BIPM) to be measured in the ionization chambers of the International Reference System (SIR) for comparison purposes. The liquid scintillation samples were also measured in a new portable TDCR system with three channel photomultipliers. Although this system has a much lower counting efficiency, the activity was in satisfactory agreement with the conventional TDCR system. The usage of the portable TDCR system, thus, provides an important test of the free parameter model. - Highlights: • Iron-59 was measured by means of liquid scintillation counters. • CIEMAT/NIST efficiency tracing and the TDCR method were applied. • The models were extended for complex decay schemes. • The relative standard uncertainty was found to be 0.16%

  20. Chromium content of selected Greek foods.

    Bratakos, Michael S; Lazos, Evangelos S; Bratakos, Sotirios M


    The total chromium content of a wide variety of Greek foods was determined by graphite furnace atomic absorption spectroscopy (GFAAS). Meat, fish and seafood, cereals and pulses were rich sources of chromium (>0.100 microg/g). Fruits, milk, oils and fats and sugar were poor sources. Differences in chromium content were found between different food classes from Greece and those from some other countries. Based on available food consumption data and chromium levels in this study, it was estimated that the chromium intake of Greeks is 143 microg/day, with vegetables, cereals and meat being the main contributors. PMID:12083715

  1. Determination of chromium combined with DNA, RNA and protein in chromium-rich brewer's yeast

    The contents of chromium in the DNA, RNA and protein fractions separated from chromium-rich and normal brewer's yeast were determined with the neutron activation analysis in order to study the combination of Cr with DNA, RNA and protein in chromium-rich brewer's yeast. The results showed that the extracting rats and concentrations of DNA, RNA and protein had no significant difference in two types of yeast, but the chromium contents of DNA, RNA and protein in the chromium-rich yeast were significantly higher than those in the normal. In addition, the content of chromium in DNA was much higher than that in RNA and protein, which indicated that the inorganic chromium compounds entered into the yeast cell, during the yeast cultivation in the culture medium containing chromium were converted into organic chromium compounds combined with DNA, RNA and protein

  2. 28 CFR 59.1 - Introduction.


    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Introduction. 59.1 Section 59.1 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) GUIDELINES ON METHODS OF OBTAINING DOCUMENTARY MATERIALS HELD BY THIRD PARTIES § 59.1 Introduction. (a) A search for documentary materials necessarily...

  3. 29 CFR 1926.59 - Hazard communication.


    ... 29 Labor 8 2010-07-01 2010-07-01 false Hazard communication. 1926.59 Section 1926.59 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... § 1926.59 Hazard communication. Note: The requirements applicable to construction work under this...

  4. 49 CFR 192.59 - Plastic pipe.


    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  5. 40 CFR 59.207 - Test methods.


    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Test methods. 59.207 Section 59.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL... Compound Emission Standards for Consumer Products § 59.207 Test methods. Each manufacturer or...

  6. 31 CFR 103.59 - Criminal penalty.


    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Criminal penalty. 103.59 Section 103.59 Money and Finance: Treasury Regulations Relating to Money and Finance FINANCIAL RECORDKEEPING AND REPORTING OF CURRENCY AND FOREIGN TRANSACTIONS General Provisions § 103.59 Criminal penalty. (a) Any...

  7. 49 CFR 801.59 - Geological records.


    ... 49 Transportation 7 2010-10-01 2010-10-01 false Geological records. 801.59 Section 801.59... PUBLIC AVAILABILITY OF INFORMATION Exemption From Public Disclosure § 801.59 Geological records. Pursuant to 5 U.S.C. 552(b)(9), records concerning geological wells are exempt from public disclosure....

  8. 40 CFR 59.106 - Variance.


    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Variance. 59.106 Section 59.106... Compound Emission Standards for Automobile Refinish Coatings § 59.106 Variance. (a) Any regulated entity... control may apply in writing to the Administrator for a temporary variance. The variance application...

  9. 40 CFR 59.206 - Variances.


    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Variances. 59.206 Section 59.206... Compound Emission Standards for Consumer Products § 59.206 Variances. (a) Any regulated entity who cannot... control may apply in writing to the Administrator for a variance. The variance application shall...

  10. 40 CFR 59.102 - Standards.


    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Standards. 59.102 Section 59.102... VOLATILE ORGANIC COMPOUND EMISSION STANDARDS FOR CONSUMER AND COMMERCIAL PRODUCTS National Volatile Organic Compound Emission Standards for Automobile Refinish Coatings § 59.102 Standards. (a) Except as provided...

  11. 14 CFR 65.59 - Skill requirements.


    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Skill requirements. 65.59 Section 65.59 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Aircraft Dispatchers § 65.59 Skill requirements....

  12. 25 CFR 700.59 - Displaced person.


    ... 25 Indians 2 2010-04-01 2010-04-01 false Displaced person. 700.59 Section 700.59 Indians THE... Policies and Instructions Definitions § 700.59 Displaced person. Displaced person means a member of the... residing within the area partitioned to the Hopi Tribe who must be relocated pursuant to the Act. This...

  13. 50 CFR 32.59 - Rhode Island.


    ... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Rhode Island. 32.59 Section 32.59 Wildlife... § 32.59 Rhode Island. The following refuge units have been opened for hunting and/or fishing and are listed in alphabetical order with applicable refuge-specific regulations. Block Island National...

  14. 42 CFR 59.213 - [Reserved


    ... 42 Public Health 1 2010-10-01 2010-10-01 false 59.213 Section 59.213 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Grants for Family Planning Service Training § 59.213...

  15. 33 CFR 401.59 - Pollution.


    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Pollution. 401.59 Section 401.59 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT CORPORATION, DEPARTMENT OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.59 Pollution. (a) No vessel shall:...

  16. 42 CFR 59.209 - Civil rights.


    ... issued by the Secretary of Health and Human Services with the approval of the President (45 CFR part 80). ... 42 Public Health 1 2010-10-01 2010-10-01 false Civil rights. 59.209 Section 59.209 Public Health... Grants for Family Planning Service Training § 59.209 Civil rights. Attention is called to...

  17. 14 CFR 13.59 - Evidence.


    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Evidence. 13.59 Section 13.59 Aeronautics... AND ENFORCEMENT PROCEDURES Rules of Practice for FAA Hearings § 13.59 Evidence. (a) Each party to a hearing may present the party's case or defense by oral or documentary evidence, submit evidence...

  18. 42 CFR 59.207 - Payments.


    ... 42 Public Health 1 2010-10-01 2010-10-01 false Payments. 59.207 Section 59.207 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Grants for Family Planning Service Training § 59.207 Payments. The Secretary shall from time to time...

  19. 42 CFR 59.12 - Additional conditions.


    ... 42 Public Health 1 2010-10-01 2010-10-01 false Additional conditions. 59.12 Section 59.12 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Project Grants for Family Planning Services § 59.12 Additional conditions. The Secretary may,...

  20. Tissues and urinary chromium concentrations in rats fed high-chromium diets

    Complete text of publication follows. Chromium is an essential trace elements and enhances the function of insulin as a form of chromodulin. In the subjects with a certain type of diabetics, 200 to 1,000 μg/d of chromium is administered to reduced the symptoms of diabetics. However, although there are not any health-promotive effects of chromium-administration in healthy subjects, various types of chromium supplements are commercially available in many countries; the adverse effects caused by an excessive chromium intake are feared. In the present study, to clarify the tolerable upper limit of chromium, tissue and urinary chromium concentrations, liver function and iron status were examined in rats fed high-chromium diets. Thirty-six male 4-weeks Wistar rats were divided into six groups and fed casein-based diets containing 1, 10 or 100 μg/g of chromium as chromium chloride (CrCl3) or chromium picolinate (CrPic) for 4 weeks. After the feeding, chromium concentrations in liver, kidney, small intestine and tibia were determined by inductively coupled plasma-mass spectrometry. In addition, urine samples were collected on 3rd to 4th week and their chromium concentrations were also determined. Chromium concentrations in liver, kidney, small intestine and tibia were elevated with increase of dietary chromium concentration. Urinary chromium excretion was also elevated with the increase of dietary chromium and the rate of urinary chromium excretion was less than 2% to dietary chromium intake in all the experimental groups. In the administration of 100 μg/g of chromium, rats given CrCl3 showed significantly higher tibia chromium concentration and lower urinary chromium excretion than those given CrPic. There were not any differences in iron status among the experimental groups. Activities of serum aspartate aminotransferase and alanine aminotransferase in rats fed diet containing 100 μg/g of chromium as CrPic were significantly higher than those in rats fed other diets.

  1. Food Chromium Contents, Chromium Dietary Intakes And Related Biological Variables In French Free-Living Elderly

    Chromium (Cr III), an essential trace element, functions in potentiating insulin sensitivity, regulating glucose homeostasis, improving lipid profile, and maintaining lean body mass. Glucose intolerance and chromium deficiency increase with age, and could be aggravating factors of the metabolic synd...

  2. Soils contaminated with hexavalent chromium

    Fonseca, Bruna Catarina da Silva


    Tese de doutoramento em Engenharia Química e Biológica The interest in environmental soil science has been growing in the last years due to the continuous degradation of this major natural resource. With this in mind, and because chromium and lead are two of the most toxic heavy metals frequently detected as soil contaminants in the Portuguese territory, the study and development of few remediation techniques and the indissociable description of the sorption and migration of...

  3. Carbon, chromium and molybdenum contents

    This work describes solidification experiments on white cast iron, with 15 and 20% of chromium, 2.3, 3.0 and 3.6 % of carbon and 0.0, 1.5 and 2.5 % of molybdenum in test de samples with 30 mm diameter. Measurements were performed on the austenite and eutectic formation arrests, the number of the eutectic carbide particles relative to the total and the eutectic volumes, and the volume fraction of the primary austenite

  4. Preparation and Characterization of Nanocrystalline Hard Chromium Coatings Using Eco-Friendly Trivalent Chromium Bath

    V. S. Protsenko; V. O Gordiienko; Danilov, F. I.; Kwon, S.C.


    A new aqueous sulfate trivalent chromium bath is described. The chromium bath contains formic acid and carbamide as complexing agents. Chromium was deposited at a temperature of 30÷40 oC and a cathode current density of 10÷25 A dm-2. The bath allows obtaining thick (up to several hundred micrometers) hard chromium coatings with nanocrystalline structure. The electrodeposition rate reaches 0.8÷0.9 µm min-1.


    A. R. Asgari ، F. Vaezi ، S. Nasseri ، O. Dördelmann ، A. H. Mahvi ، E. Dehghani Fard


    Removal of chromium can be accomplished by various methods but none of them is cost-effective in meeting drinking water standards. For this study, granular ferric hydroxide was used as adsorbent for removal of hexavalent chromium. Besides, the effects of changing contact time, pH and concentrations of competitive anions were determined for different amounts of granular ferric hydroxide. It was found that granular ferric hydroxide has a high capacity for adsorption of hexavalent chromium from ...

  6. Inoculation of chromium white cast iron

    D. Kopyciński


    Full Text Available It has been proved that an addition of boron carbide introduced as an inoculant to the chromium white cast iron changes the structureof castings. Castings after inoculation revealed a different structure with numerous grains. Primary precipitates of chromium carbide also appeared, reducing the mechanical properties of as-cast parts. Properly established heat treatment regime makes chromium iron castings regain their, originally high, mechanical properties.

  7. Inoculation of chromium white cast iron

    D. Kopyciński


    It has been proved that an addition of boron carbide introduced as an inoculant to the chromium white cast iron changes the structureof castings. Castings after inoculation revealed a different structure with numerous grains. Primary precipitates of chromium carbide also appeared, reducing the mechanical properties of as-cast parts. Properly established heat treatment regime makes chromium iron castings regain their, originally high, mechanical properties.

  8. 10 CFR 50.59 Evaluation

    10 CFR 50.59 evaluations are scrutinized from a PRA perspective. In this paper strengths and weaknesses of PRA (both as a process and a product) and 50.59 evaluations are considered. The essential elements for performing an effective management of plant changes are discussed. Recommendations on activities that the NRC and the Utility can take to facilitate the effective 50.59 evaluations and management of plant changes are made

  9. Permeation of chromium salts through human skin in vitro

    Gammelgaard, Bente; Fullerton, A; Avnstorp, C;


    of the dichromate solution. Chromium skin levels increased with increasing concentrations of applied chromium salts up to 0.034 M Cr. The amount of chromium in recipient phase and skin layers increased with increasing pH when the applied solution contained potassium dichromate. This was ascribed to a decreased skin...... barrier function of the skin. The amount of chromium found in all skin layers after application of chromium chloride decreased with increasing pH due to lower solubility of the salt. The % of chromium found in the recipient phase as chromium(VI) increased with increasing total chromium concentration...... indicating a limited reduction ability of the skin in vitro....

  10. 28 CFR 59.4 - Procedures. 1


    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Procedures. 1 59.4 Section 59.4 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) GUIDELINES ON METHODS OF OBTAINING DOCUMENTARY MATERIALS HELD BY... importance to the investigation or prosecution for which they are sought; and (iii) The application for...

  11. 38 CFR 59.30 - Documentation.


    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Documentation. 59.30... STATES FOR CONSTRUCTION OR ACQUISITION OF STATE HOMES § 59.30 Documentation. For a State to obtain a grant and grant funds under this part, the State must submit to VA documentation that the site of...

  12. 28 CFR 59.3 - Applicability.


    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Applicability. 59.3 Section 59.3 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) GUIDELINES ON METHODS OF OBTAINING DOCUMENTARY MATERIALS HELD BY... through subpoena or request because they are in the possession of a person whose identity is unknown...

  13. 44 CFR 59.4 - References.


    ... 1954, as amended by the Housing and Community Development Act of 1974 (24 CFR 600.72). (12) Executive... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false References. 59.4 Section 59.4... References. (a) The following are statutory references for the National Flood Insurance Program, under...

  14. 34 CFR 106.59 - Advertising.


    ... 34 Education 1 2010-07-01 2010-07-01 false Advertising. 106.59 Section 106.59 Education Regulations of the Offices of the Department of Education OFFICE FOR CIVIL RIGHTS, DEPARTMENT OF EDUCATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL...

  15. 7 CFR 15a.59 - Advertising.


    ... 7 Agriculture 1 2010-01-01 2010-01-01 false Advertising. 15a.59 Section 15a.59 Agriculture Office of the Secretary of Agriculture EDUCATION PROGRAMS OR ACTIVITIES RECEIVING OR BENEFITTING FROM FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs...

  16. 45 CFR 86.59 - Advertising.



  17. Chromium in aqueous nitrate plutonium process streams: Corrosion of 316 stainless steel and chromium speciation

    This study was undertaken to determine if chromium(+6) could exist in plutonium process solutions under normal operating conditions. Four individual reactions were studied: the rate of dissolution of stainless steel, which is the principal source of chromium in process solutions; the rate of oxidation of chromium(+3) to chromium(+6) by nitric acid; and the reduction of chromium(+6) back to chromium(+3) by reaction with stainless steel and with oxalic acid. The stainless steel corrosion rate was found to increase with increasing nitric acid concentration, increasing hydrofluoric acid concentration, and increasing temperature. Oxidation of chromium(+3) to chromium(+6) was negligible at room temperature and only became significant in hot concentrated nitric acid. The rate of reduction of chromium(+6) back to chromium(+3) by reaction with stainless steel or oxalic acid was found to be much greater than the rate of the reverse oxidation reaction. Based on these findings and taking into account normal operating conditions, it was determined that although there would be considerable chromium in plutonium process streams it would rarely be found in the (+6) oxidation state and would not exist in the (+6) state in the final process waste solutions

  18. C59N Peapods Sensing the Temperature

    Toshiro Kaneko


    Full Text Available We report the novel photoresponse of nanodevices made from azafullerene (C59N-encapsulated single-walled carbon nanotubes (C59N@SWNTs, so called peapods. The photoconducting properties of a C59N@SWNT are measured over a temperature range of 10 to 300 K under a field-effect transistor configuration. It is found that the photosensitivity of C59N@SWNTs depends very sensitively on the temperature, making them an attractive candidate as a component of nanothermometers covering a wide temperature range. Our results indicate that it is possible to read the temperature by monitoring the optoelectronics signal of C59N@SWNTs. In particular, sensing low temperatures would become more convenient and easy by giving a simple light pulse.

  19. Alkane dehydrogenation over supported chromium oxide catalysts

    Weckhuysen, B.M.; Schoonheydt, R.A.


    The dehydrogenation of alkanes over supported chromium oxide catalysts in the absence of oxygen is of high interest for the industrial production of propene and isobutene. In this review, a critical overview is given of the current knowledge nowadays available about chromium-based dehydrogenation ca

  20. Hardness, elastic, and electronic properties of chromium monoboride

    Han, Lei [Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); College of Construction Engineering, Jilin University, Changchun, Jilin 130061 (China); Wang, Shanmin; Zhu, Jinlong [HiPSEC and Department of Physics, University of Nevada, Las Vegas, Nevada 89154 (United States); Han, Songbai [Neutron Scattering Laboratory, China Institute of Atomic Energy, Beijing 102413 (China); Li, Wenmin; Chen, Bijuan; Wang, Xiancheng; Yu, Xiaohui, E-mail:, E-mail:, E-mail:; Long, Youwen; Cheng, Jinguang; Jin, Changqing [Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Liu, Baochang, E-mail:, E-mail:, E-mail: [College of Construction Engineering, Jilin University, Changchun, Jilin 130061 (China); Zhang, Ruifeng, E-mail:, E-mail:, E-mail: [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Zhang, Jianzhong [LANSCE Division, Los Alamos National Lab, Los Alamos, New Mexico 87545 (United States); Zhao, Yusheng [Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); HiPSEC and Department of Physics, University of Nevada, Las Vegas, Nevada 89154 (United States)


    We report high-pressure synthesis of chromium monoboride (CrB) at 6 GPa and 1400 K. The elastic and plastic behaviors have been investigated by hydrostatic compression experiment and micro-indentation measurement. CrB is elastically incompressible with a high bulk modulus of 269.0 (5.9) GPa and exhibits a high Vickers hardness of 19.6 (0.7) GPa under the load of 1 kg force. Based on first principles calculations, the observed mechanical properties are attributed to the polar covalent Cr-B bonds interconnected with strong zigzag B-B covalent bonding network. The presence of metallic Cr bilayers is presumably responsible for the weakest paths in shear deformation.

  1. Neutron scattering and models: Chromium

    Differential neutron elastic-scattering cross sections of elemental chromium are measured from 4.5 ∼ 10 MeV in steps of ∼ 0.5 MeV and at ≥ 40 scattering angles distributed between ∼ 17 degree--160 degree. Concurrently differential cross sections for the inelastic neutron excitation of the yrast 2+ (1.434 MeV) level in d52Cr are determined. In addition, broad inelastically-scattered neutron groups are observed corresponding to composite excitation of levels up to ∼ 5.5 MeV in the various chromium isotopes. These experimental results are combined with low-energy values previously reported from this laboratory, with recent ∼ 8 → 15 MeV data measured at the Physikalisch-Technische Bundesanstalt and with a 21.6 MeV result from the literature to form an extensive neutron-scattering data base which is interpreted in the context of spherical-optical and coupled-channels (rotational and vibrational) models. These models reasonably describe the observables but indicate rather large energy-dependent parameter trends at low energies similar to those previously reported near the peak of the So strength function in studies at this laboratory. The physical implications of the measurements and models are discussed including deformation, coupling, dispersive and asymmetry effects

  2. Chemical Stability of Chromium Carbide and Chromium Nitride Powders Compared with Chromium Metal in Synthetic Biological Solutions

    Tao Jiang; Inger Odnevall Wallinder; Gunilla Herting


    Chromium carbide (Cr-C) and chromium nitride (Cr-N) powders were compared with a chromium metal powder (Cr-metal) to evaluate their chemical stability in solution. All three powders were exposed in five different synthetic biological solutions of varying pH and chemical composition simulating selected human exposure conditions. Characterisation of the powders, using GI-XRD, revealed that the predominant bulk crystalline phases were Cr7C3 and Cr2N for Cr-C and Cr-N respectively. The outermost ...

  3. Low-chromium reduced-activation chromium-tungsten steels

    Klueh, R.L.; Alexander, D.J.; Maziasz, P.J. [Oak Ridge National Lab., TN (United States)


    Bainitic microstructures formed during continuous cooling can differ from classical upper and lower bainite formed during isothermal transformation. Two types of non-classical bainite were observed depending on the cooling rate: carbide-free acicular bainite at rapid cooling rates and granular bainite at slower cooling rates. The Charpy impact toughness of the acicular ferrite was found to be considerably better than for the granular bainite. It was postulated that alloying to improve the hardenability of the steel would promote the formation of acicular bainite, just as increasing the cooling rate does. To test this, chromium and tungsten were added to the 2 1/4Cr-2W and 2 1/4Cr-2WV steel compositions to increase their hardenability, and the microstructures and mechanical properties were examined.

  4. 40 CFR 59.514 - Circumvention.


    ... Compound Emission Standards for Aerosol Coatings § 59.514 Circumvention. Each manufacturer, distributor, and importer of an aerosol coating or component subject to the provisions of this subpart must...

  5. Bainitic chromium-tungsten steels with 3 pct chromium

    Previous work on 3Cr-1.5MoV (nominally Fe-3Cr-2.5Mo-0.25V-0.1C), 2.25Cr-2W (Fe-2.25Cr-2W-0.1C), and 2.25Cr-2WV (Fe-2.25Cr-2W-0.25V-0.1C) steels indicated that the impact toughness of these steels depended on the microstructure of the bainite formed during continuous cooling from the austenization temperature. Microstructures formed during continuous cooling can differ from classical upper and lower bainite formed during isothermal transformation. Two types of nonclassical microstructures were observed depending on the cooling rate: carbide-free acicular bainite at rapid cooling rates and granular bainite at slower cooling rates. The Charpy impact toughness of the acicular ferrite was considerably better than for the granular bainite. It was postulated that alloying to improve the hardenability of the steel would promote the formation of acicular bainite, just as increasing the cooling rate does. To test this, chromium and tungsten were added to the 2.25Cr-2W and 2.25Cr-2WV steel compositions to increase their hardenability. Charpy testing indicated that the new 3Cr-W and 3Cr-WV steels had improved impact toughness, as demonstrated by lower ductile-brittle transition temperatures and higher upper-shelf energies. This improvement occurred with less tempering than was necessary to achieve similar toughness for the 2.25Cr steels and for high-chromium (9 to 12 pct Cr) Cr-W and Cr-Mo steels

  6. Reproductive toxicological aspects of chromium in males

    To expand our present understanding of the effects of chromium on male fertility a number of studies were designed to achieve this through the use of chromium intoxicated experimental animals and through investigation of sexual hormones and sperm quality in welders. Also in view of the lack of an experimental model for effects of noxious substance on the epididymal spermatozoa the main objectives of the series of studies reviewed here were: A. To establish a model for evaluation of epididymal sperm count and motility in the rat. B. To investigate and compare the effects of tri- and hexavalent chromium on epididymal spermatozoa. Further to describe the effects of low-dose long-time exposure of rats to the most toxicological interesting chromium oxidative state - hexavalent chromium. C. By the use of autoradiography and γ-countinuing to expand the present knowledge on the distribution of chromium in the body with special reference to the male reproductive organs. D. To describe the effects of exposure to hexavalent chromium in welding fume on levels of sexual hormones and semen parameters in welders. (EG)

  7. A59 waste repackaging database (AWARD)

    This paper sets out the requirements for AWARD (the A59 Waste Repackaging Database); a computer-based system to record LLW sorting and repacking information from the North Cave Line in A59. A solution will be developed on the basis of this document. AWARD will record and store details entered from waste sorting and LLW repackaging operations. This document will be used as the basis of the development of the host computer system. (Author)

  8. Synthesis of Chromium (Ⅲ) 5-aminosalicylate

    LI Wei; HAO Er-jun; JIANG Yu-qin


    As we all known that diabetes is a chronic disease with major health consequences.Research has revealed that the occurrence of diabetes have great thing to do with the chromium deficient. Almost 40 years after the first report of glucose tolerance factor(GTF) [1], no conclusive evidence for an isolable ,biologically active form of chromium exited. Three materials have been proposed to be the biologically active form of chromium: "glucose tolerance factor", chromium Picolinate and low-molecular-weight chromium-binding substance (LWMCr) [2] . So there is potential for the design of new chromium drugs .5-Aminosalicylic acid (5-ASA) is identified as an active component in the therapy of inflammatory bowel disease (IBD) such as Crohn's disease and ulcerative colitis . The therapeutic action of 5-ASA is believed to be coupled to its ability to act as a free radical scavenger [3-4],acting locally on the inflamed colonic mucosa [5-7]. However, the clinical use of 5-ASA is limited, since orally administered 5-ASA is rapidly and completely absorbed from the upper gastrointestinal tract and therefore the local therapeutic effects of 5-ASA in the colon is hardly expected.In this paper, we report the synthesis of chromium(Ⅲ)5-aminosalicylate from 5-ASA and CrCl3. 6H2O.The synthesis route is as follow:The complex has been characterized by elemental analysis, IR spectra, X-ray powder diffractionand TG-DTA . They indicate that the structure is tris(5-ASA) Chromium . Experiments show that thecomplex has a good activity for supplement tiny dietary chromium, lowering blood glucose levels,lowering serum lipid levels and in creasing lean body mass .

  9. Chromium in leather footwear-risk assessment of chromium allergy and dermatitis

    Thyssen, Jacob P; Strandesen, Maria; Poulsen, Pia B;


    Background. Chromium-tanned leather footwear, which releases >3 ppm hexavalent Cr(VI), may pose a risk of sensitizing and eliciting allergic dermatitis. Objectives. To determine the content and potential release of chromium in leather footwear and to discuss the prevention of chromium contact...... allergy and dermatitis. Methods. Sixty pairs of leather shoes, sandals and boots (20 children's, 20 men's, and 20 women's) were purchased in Copenhagen and examined with X-ray fluorescence spectroscopy. Chromium was extracted according to the International Standard, ISO 17075. The detection level for Cr......(VI) was 3 ppm. Results. Chromium was identified in 95% of leather footwear products, the median content being 1.7% (range 0-3.3%). No association with store category or footwear category was found. A tendency for there to be a higher chromium content in footwear with high prices was shown (p(trend) = 0...

  10. Characteristics of chromium-allergic dermatitis patients prior to regulatory intervention for chromium in leather

    Bregnbak, David; Thyssen, Jacob P; Zachariae, Claus;


    BACKGROUND: Chromium-tanned leather articles currently constitute the most important cause of contact allergy to chromium in Denmark. A regulation on the content of hexavalent chromium in leather was adopted in November 2013 by the EU member states. OBJECTIVES: To characterize patients with...... chromium allergy and their disease, to serve as a baseline for future studies on the potential effect of the new regulation on chromium in leather. METHODS: A questionnaire case-control study was performed on 155 dermatitis patients with positive patch test reactions to potassium dichromate and a matched...... control group of 621 dermatitis patients. Comparisons were made by use of a χ(2) -test and the Mann-Whitney U-test. Logistic regression analyses were used to test for associations. RESULTS: Sixty-six per cent of chromium-allergic patients had a positive history of contact dermatitis caused by leather...

  11. Chromium intensification of a processed dental radiograph

    This study was undertaken to determine (1) the usefulness of chromium intensifier to improve the diagnostic quality of light radiograph; (2) the effect of chromium intensifier on density contrast; and (3) the effect of various chemical concentrations on density. The following results obtained: 1. CHROMIUM INTENSIFIER is useful for intensifying and improving the diagnostic quality of a light dental radiograph. 2. The degree of intensification can be controlled by varying bleaching time, repeating the processing, varying the proportions of the potassium bicarbonate and hydrochloric acid solutions. 3. The image produced is black and permanent. 4. The intensifier increases density and contrast

  12. Chromium (VI) adsorption on boehmite

    Granados-Correa, F. [Instituto Nacional de Investigaciones Nucleares, Apartado Postal 18-1027 Col., Escandon, Delegacion Miguel Hidalgo, C.P. 11801 Mexico, D.F. (Mexico)], E-mail:; Jimenez-Becerril, J. [Instituto Nacional de Investigaciones Nucleares, Apartado Postal 18-1027 Col., Escandon, Delegacion Miguel Hidalgo, C.P. 11801 Mexico, D.F. (Mexico)


    Boehmite was synthesized and characterized in order to study the adsorption behavior and the removal of Cr(VI) ions from aqueous solutions as a function of contact time, initial pH solution, amount of adsorbent and initial metal ion concentration, using batch technique. Adsorption data of Cr(VI) on the boehmite were analyzed according to Freundlich, Langmuir and Dubinin-Radushkevich (D-R) adsorption models. Thermodynamic parameters for the adsorption system were determinated at 293, 303, 313 and 323 K temperatures. The kinetic values and thermodynamic parameters from the adsorption process show that the Cr(VI) ions adsorption on boehmite is an endothermic and spontaneous process. These results show that the boehmite could be considered as a potential adsorbent for chromium ions in aqueous solutions.

  13. Chromium – An essential mineral

    Merlin D Lindemann


    Full Text Available The status of chromium (Cr is not a new question. Cr is clearly an essential nutrient; this is a position that has been held for over three decades by individual scientists, groups of scientists, and governmental committees. The most uniform response across species with regard to Cr deficiency symptoms that are responsive to Cr supplementation are alterations in glucose metabolism with special reference to peripheral tissue sensitivity to insulin. Because the body’s ability to control blood glucose is critical to many life functions, and loss of ability to adequately control blood glucose can lead to many health debilitations, a consequence of Cr supplementation can be improved health and reproductive outcomes as well as improved survival rate or life span.

  14. Occupational asthma due to chromium.

    Leroyer, C; Dewitte, J D; Bassanets, A; Boutoux, M; Daniel, C; Clavier, J


    We describe a 28-year-old subject employed as a roofer in a construction company since the age of 19, who developed work-related symptoms of a cough, shortness of breath, wheezing, rhinitis and headaches. A description of a usual day at work suggested that the symptoms worsened while he was sawing corrugated fiber cement. Baseline spirometry was normal, and there was a mild bronchial hyperresponsiveness to carbachol. A skin patch test to chromium was negative. A specific inhalation challenge showed a boderline fall in forced expiratory volume in 1 s (FEV1) after exposure to fiber cement dust. Exposure to nebulization of potassium dichromate (K2Cr2O7), at 0.1 for 30 min, was followed by an immediate fall by 20% FEV1. Simultaneously, a significant increase in bronchial hyperresponsiveness was demonstrated. PMID:9782225

  15. Chromium isotope uptake in carbonates

    Rodler, Alexandra

    Chromium (Cr) is a redox sensitive element potentially capable of tracing fine-scale fluctuations of the oxygenation of Earth’s early surface environments and seawater. The Cr isotope composition of carbonates could perhaps be used as paleo-redox proxy to elucidate changes in the geological past....... Processes that potentially fractionate Cr isotopes, perhaps during deposition, burial and alteration need to be constrained.Previous studies have shown that Cr isotopes are fractionated during oxidative weathering on land, where heavy Cr isotopes are preferentially removed with Cr(VI) while residual soils...... retain an isotopically light Cr signature. Cr(VI) enriched in heavy Cr isotopes is then transported via river waters to the oceans and sequestered into marine sediments. Marine chemical sediments such asbanded iron formations and modern marine carbonates have proven useful in recording the Cr isotope...

  16. Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection

    Gammelgaard, Bente; Jøns, O; Nielsen, B


    A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both sp....... The detection limit was 0.5 micrograms l-1 for both species. Data were in agreement with Zeeman-effect background corrected atomic absorption spectrometry measurements....


    Suyuan Yu


    Cr2O3 is considered as the dominant incineration product during the combustion disposal of chromium waste. A hydrogen/air diffusion flame was employed to simulate the industrial process of incineration. Cr2O3 aerosols were generated inside the flame by the gas phase reaction of chromium and oxygen. Chromium came from the rapid decomposition of chromium hexacarbonyl (Cr(CO)6) at room temperature and was carried into the combustion chamber by hydrogen. Aerosol and clusters can then be easily formed in the flame by nucleation and coagulation. A two dimensional Discrete-Sectional Model (DSM) was adopted to calculate the Cr2O3 aerosol behavior. The experimental measurement method was Dynamic Light Scattering. The numerically predicted results agreed well with those of the experimental measurement. Both results show that the Cr2O3 aerosol size reached about 70 nanometers at the flame top.

  18. Potentiometry: A Chromium (III) -- EDTA Complex

    Hoppe, J. I.; Howell, P. J.


    Describes an experiment that involves the preparation of a chromium (III)-EDTA compound, a study of its infrared spectrum, and the potentiometric determination of two successive acid dissociation constants. (Author/GS)

  19. Kinetics of Voluminal Reduction of Chromium Ore Fines Containing Coal by Microwave Heating

    CHEN Jin; WANG She-bin; ZHANG Meng; LIU Jin-ying; ZHOU Jian-xiong


    The kinetics of voluminal reduction of chromium ore fines containing coal(COFCC)by microwave heating was studied.When the molar ratio of carbon to oxygen was 0.84 and that of CaO to SiO2 was 0.39 in COFCC,the temperature-rising rate of COFCC by microwave heating was 62.5℃/min,68.75℃/min,70.59℃/rain,and 72.22℃/min at 1 000℃,1100℃,1200℃,and 1300℃,respectively.The results show that the voluminal reduction of COFCC by microwave heating at solid-solid phase is first order reaction,with the apparent activation energy of 51.480 kJ/mol.The limiting step of reaction rate for the overall reaction is the mass transfer of CO in the reduced product layer between dielectric particles of chromium ore and coal.


    Roman-Zuniga, C. G. [Instituto de Astronomia, Universidad Nacional Autonoma de Mexico, Km 103 Carr. Tijuana-Ensenada, Ensenada BC 22860 (Mexico); Frau, P.; Girart, J. M. [Institut de Ciencies de l' Espai (CSIC-IEEC), Campus UAB, Facultat de Ciencies, Torre C-5p, 08193 Bellaterra, Catalunya (Spain); Alves, Joao F., E-mail: [Institute of Astronomy, University of Vienna, Tuerkenschanzstr. 17, 1180 Vienna (Austria)


    The dense molecular clump at the center of the Barnard 59 (B59) complex is the only region in the Pipe Nebula that has formed a small, stellar cluster. The previous analysis of a high-resolution near-IR dust extinction map revealed that the nuclear region in B59 is a massive, mostly quiescent clump of 18.9 M{sub Sun }. The clump shows a monolithic profile, possibly indicating that the clump is on the way to collapse, with no evident fragmentation that could lead to another group of star systems. In this paper, we present new analysis that compares the dust extinction map with a new dust emission radio-continuum map of higher spatial resolution. We confirm that the clump does not show any significant evidence for prestellar fragmentation at scales smaller than those probed previously.

  1. Bioremediation of chromium solutions and chromium containing wastewaters.

    Malaviya, Piyush; Singh, Asha


    Cr(VI) represents a serious threat to human health, living resources and ecological system as it is persistent, carcinogenic and toxic, whereas, Cr(III), another stable oxidation state of Cr, is less toxic and can be readily precipitated out of solution. The conventional methods of Cr(VI) removal from wastewaters comprise of chemical reduction followed by chemical precipitation. However, these methods utilize large amounts of chemicals and generate toxic sludge. This necessitates the need for devising an eco-technological strategy that would use the untapped potential of the biological world for remediation of Cr(VI) containing wastewaters. Among several viable approaches, biotransformation of Cr(VI) to relatively non-toxic Cr(III) by chromium resistant bacteria offers an economical- and environment-friendly option for its detoxification. Various studies on use of Cr(VI) tolerant viable bacterial isolates for treatment of Cr(VI) containing solutions and wastewater have been reported. Therefore, a detailed account of mechanisms and processes involved in bioreduction of Cr(VI) from solutions and wastewaters by bacterial isolates are the focus of this review article in addition to a discussion on toxicity of Cr(VI) on bacterial strains and various factors affecting Cr(VI) bioreduction. PMID:25358056

  2. Dietary chromium and nickel enhance UV-carcinogenesis in skin of hairless mice

    The skin cancer enhancing effect of chromium (in male mice) and nickel in UVR-irradiated female Skh1 mice was investigated. The dietary vitamin E and selenomethionine were tested for prevention of chromium-enhanced skin carcinogenesis. The mice were exposed to UVR (1.0 kJ/m2 3x weekly) for 26 weeks either alone, or combined with 2.5 or 5.0 ppm potassium chromate, or with 20, 100 or 500 ppm nickel chloride in drinking water. Vitamin E or selenomethionine was added to the lab chow for 29 weeks beginning 3 weeks before the start of UVR exposure. Both chromium and nickel significantly increased the UVR-induced skin cancer yield in mice. In male Skh1 mice, UVR alone induced 1.9 ± 0.4 cancers/mouse, and 2.5 or 5.0 ppm potassium chromate added to drinking water increased the yields to 5.9 ± 0.8 and 8.6 ± 0.9 cancers/mouse, respectively. In female Skh1 mice, UVR alone induced 1.7 ± 0.4 cancers/mouse, and the addition of 20, 100 or 500 ppm nickel chloride increased the yields to 2.8 ± 0.9, 5.6 ± 0.7 and 4.2 ± 1.0 cancers/mouse, respectively. Neither vitamin E nor selenomethionine reduced the cancer yield enhancement by chromium. These results confirm that chromium and nickel, while not good skin carcinogens per se, are enhancers of UVR-induced skin cancers in Skh1 mice. Data also suggest that the enhancement of UVR-induced skin cancers by chromate may not be oxidatively mediated since the antioxidant vitamin E as well as selenomethionine, found to prevent arsenite-enhanced skin carcinogenesis, failed to suppress enhancement by chromate

  3. Diminishing Chromium Use on Combined Chromium-Gambier Tanning Process Upon the Characteristics of Tanned Leather

    A. Kasim


    Full Text Available The research was aimed to investigate the influence of minimizing chromium use on combined chromium-gambier process upon the characteristics of tanned leather. At the first stage of tanning process, chromium was used and in the second stage it was replaced by gambier. The raw material used was dried saline-preserved goat skin. The treatments applied on the tanning process were the different concentrations of chromium ranging from the highest level of 6% to the lowest level of 1% which was then re-tanned by using 8% concentration of gambier. The examination parameters included chemical and physical properties as well as visual investigation on the tanned leather in accordance with SNI-06-0463-1989-A. The result showed that the tanning process by using 2% chromium in the first step and 8% gambier in the second step was a treatment combination producing tanned leather that met the standard. The examination on tanned leather resulted from such treatment showed 56.33% rawhide, 17.45% of bound tannin, 31.22% of tanning level, tensile strength 386.30 kg/cm2, flexibility 31.91%, leather width 1.3 mm, density 0.75 g/cm3, the leather was quite elastic with light brownish color. In conclusion, minimizing the use of chromium in the combined tanning process of chromium and gambier can be implemented to the lowest of 2% chromium concentration and 8% gambier in the first and second step, respectively.

  4. 40 CFR 59.513 - State authority.


    ..., distributor or importer of aerosol coatings or components in addition to the requirements of this subpart. (b) Requiring the manufacturer, distributor or importer of aerosol coatings or components to obtain permits... Compound Emission Standards for Aerosol Coatings § 59.513 State authority. The provisions in...

  5. 44 CFR 59.1 - Definitions.


    ...: For Federal Register citations affecting § 59.1, see the List of CFR Sections Affected, which appears... instrumentality responsible for the supervision, approval, regulation, or insuring of banks, savings and loan... definition and are akin to a river of liquid and flowing mud on the surfaces of normally dry land areas,...

  6. 38 CFR 3.59 - Parent.


    ... child if the usual family relationship existed), mother or father through adoption, or a person who for a period of not less than 1 year stood in the relationship of a parent to a veteran at any time..., and Dependency and Indemnity Compensation Relationship § 3.59 Parent. (a) The term parent means...

  7. 42 CFR 59.2 - Definitions.


    ... HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Project Grants for Family Planning Services § 59.2 Definitions. As used in this subpart: Act means the Public Health Service Act, as amended. Family means a social unit composed of one person, or two or...

  8. 42 CFR 59.11 - Confidentiality.


    ... PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Project Grants for Family Planning Services § 59.11 Confidentiality. All information as to personal facts and circumstances obtained by the project staff about individuals receiving services must be...

  9. 44 CFR 59.3 - Emergency program.


    ... insurance to be sold before a study is conducted to determine risk premium rates for the community. The program still requires upon the effective date of a FIRM the charging of risk premium rates for all new... General § 59.3 Emergency program. The 1968 Act required a risk study to be undertaken for each...

  10. 46 CFR 59.10-5 - Cracks.


    ... than 2 inches beyond the centerline of the rivet holes. (f) Cracks may be welded between tube holes in... CFR 59.01-2). For thicknesses exceeding three-fourths inch, suitable U grooves should be employed. A... from the calking edge of plates to the rivet holes of circumferential joints may be welded provided...

  11. 42 CFR 59.203 - Eligibility.


    ... PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Grants for Family Planning Service Training § 59.203 Eligibility. (a) Eligible applicants. Any public or... the effective delivery of family planning services: Provided, That the Secretary may in...

  12. 42 CFR 59.202 - Definitions.


    ... PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Grants for Family Planning Service Training § 59.202 Definitions. As used in this subpart: (a) Act means... development, the purpose of which is to promote and improve the delivery of family planning services....

  13. 42 CFR 59.205 - Project requirements.


    ... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Grants for Family Planning Service Training § 59.205 Project requirements. An approvable... to train personnel for programs where abortion is a method of family planning. (2) No portion of...

  14. 42 CFR 59.201 - Applicability.


    ... PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Grants for Family Planning Service Training § 59.201 Applicability. The regulations in this subpart are...) to provide the training for personnel to carry out family planning service programs described...

  15. Lateral stress evolution in chromium sulfide cermets with varying excess chromium

    Petel, O. E.; Appleby-Thomas, G. J.; Wood, D. C.; Capozzi, A.; Nabavi, A.; Goroshin, S.; Frost, D. L.; Hazell, P. J.


    The shock response of chromium sulfide-chromium, a cermet of potential interest as a matrix material for ballistic applications, has been investigated at two molar ratios. Using a combustion synthesis technique allowed for control of the molar ratio of the material, which was investigated under near-stoichiometric (cermet) and excess chromium (interpenetrating composite) conditions, representing chromium:sulfur molar ratios of 1.15:1 and 4:1, respectively. The compacts were investigated via the plate-impact technique, which allowed the material to be loaded under a one-dimensional state of strain. Embedded manganin stress gauges were employed to monitor the temporal evolution of longitudinal and lateral components of stress in both materials. Comparison of these two components has allowed assessment of the variation of material shear strength both with impact pressure/strain-rate and time for the two molar ratio conditions. The two materials exhibited identical material strength despite variations in their excess chromium contents.

  16. The enriched chromium neutrino source for GALLEX

    The preparation and study of an intense source of neutrinos in the form of neutron irradiated materials which are enriched in Cr-50 for use in the GALLEX solar neutrino experiment are discussed. Chromyl fluoride gas is enriched in the Cr-50 isotope by gas centrifugation and subsequently converted to a very stable form of chromium oxide. The results of neutron activation analyses of such chromium samples indicate low levels of any long-lived activities, but show that short-lived activities, in particular Na-24, may be of concern. These results show that irradiating chromium oxide enriched in Cr-50 is preferable to irradiating either natural chromium or argon gas as a means of producing a neutrino source to calibrate the GALLEX detector. These results of the impurity level analysis of the enriched chromyl fluoride gas and its conversion to the oxide are also of interest to work in progress by other members of the Collaboration investigating an alternative conversion of the enriched gas to chromium metal. 35 refs., 12 figs., 5 tabs

  17. Occupational exposure to chromium(VI compounds

    Jolanta Skowroń


    Full Text Available This article discusses the effect of chromium(VI (Cr(VI on human health under conditions of acute and chronic exposure in the workplace. Chromium(VI compounds as carcinogens and/or mutagens pose a direct danger to people exposed to them. If carcinogens cannot be eliminated from the work and living environments, their exposure should be reduced to a minimum. In the European Union the proposed binding occupational exposure limit value (BOELV for chromium(VI of 0.025 mg/m³ is still associated with high cancer risk. Based on the Scientific Commitee of Occupational Exposure Limits (SCOEL document chromium(VI concentrations at 0.025 mg/m³ increases the risk of lung cancer in 2–14 cases per 1000 exposed workers. Exposure to chromium(VI compounds expressed in Cr(VI of 0.01 mg Cr(VI/m3 is responsible for the increased number of lung cancer cases in 1–6 per 1000 people employed in this condition for the whole period of professional activity. Med Pr 2015;66(3:407–427

  18. [Occupational exposure to chromium(VI) compounds].

    Skowroń, Jolanta; Konieczko, Katarzyna


    This article discusses the effect of chromium(VI) (Cr(VI)) on human health under conditions of acute and chronic exposure in the workplace. Chromium(VI) compounds as carcinogens and/or mutagens pose a direct danger to people exposed to them. If carcinogens cannot be eliminated from the work and living environments, their exposure should be reduced to a minimum. In the European Union the proposed binding occupational exposure limit value (BOELV) for chromium(VI) of 0.025 mg/m³ is still associated with high cancer risk. Based on the Scientific Commitee of Occupational Exposure Limits (SCOEL) document chromium(VI) concentrations at 0.025 mg/m³ increases the risk of lung cancer in 2-14 cases per 1000 exposed workers. Exposure to chromium(VI) compounds expressed in Cr(VI) of 0.01 mg Cr(VI)/m3; is responsible for the increased number of lung cancer cases in 1-6 per 1000 people employed in this condition for the whole period of professional activity. PMID:26325053

  19. Flashlamp-pumped lasing of chromium-doped GSG garnet

    The implications for the practical use of chromium:GSGG in lamp-pumped tunable lasers are discussed in this paper. The authors report here some major improvements in the performance of the flashlamp-pumped chromium:GSGG laser

  20. Surface Chemistry and Spectroscopy of Chromium in Inorganic Oxides

    Weckhuysen, B. M.; Wachs, I.E.; Schoonheydt, R. A.


    Focuses on the surface chemistry and spectroscopy of chromium in inorganic oxides. Characterization of the molecular structures of chromium; Mechanics of hydrogenation-dehydrogenation reactions; Mobility and reactivity on oxidic surfaces.

  1. Studies of Some Novel Chromium Pyridine Dicarboxylate Complexes

    Chauhan Jayprakash S; Patel Rameshchandra P; Pandya Ajit V


    Chromium pyridine di-carboxylate complexes are synthesized from Chromium (III) with pyridine 2, 6- dicarboxylic acid, pyridine 2, 3 and 2, 5- dicarboxylic acids. Chromium forms colored complexes. Chromium (III) forms a violate complex with pyridine 2, 6- dicarboxylic acid and purple violate complex with pyridine 2, 3 and 2, 5- dicarboxylic acids. The job’s method indicates metal ligand ratio to be 1:2. The interpretation of UV-VIS spectra indicates octahedral geometry and IR spectra give clue...

  2. Determination of chromium combined with DNA, RNA and proteins in chromium-rich brewer's yeast by NAA

    The content of chromium in the DNA, RNA and protein fractions separated from chromium-rich and normal brewer's yeast was determined by neutron activation analysis (NAA). Our results show that the extracted relative amounts and concentrations of DNA, RNA and proteins have no significant difference for two types of yeast, but the chromium content in DNA, RNA and proteins fractions extracted from the chromium-rich yeast are substantially higher than those from the normal. In addition, the concentration of chromium in DNA is much higher than that in RNA and proteins. It is evident that the inorganic chromium compounds can enter the yeast cell during the yeast cultivation in the chromium-containing culture medium and are converted into organic chromium species, which are combined with DNA, RNA and proteins. (author)

  3. Chromium allergy and dermatitis: prevalence and main findings

    Bregnbak, David; Johansen, Jeanne D.; Jellesen, Morten Stendahl;


    The history of chromium as an allergen goes back more than a century, and includesan interventional success with national legislation that led to significant changes inthe epidemiology of chromium allergy in construction workers. The 2015 EU Leather Regulation once again put a focus on chromium...

  4. 21 CFR 73.1326 - Chromium hydroxide green.


    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.1326 Section 73.1326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1326 Chromium hydroxide green. (a) Identity. (1) The color additive chromium hydroxide green is principally hydrated chromic sesquioxide...

  5. 21 CFR 73.2326 - Chromium hydroxide green.


    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.2326 Section 73.2326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2326 Chromium hydroxide green. (a) Identity and specifications.The color additive chromium hydroxide green shall conform in identity and specifications to...

  6. Thermodynamic properties of chromium bearing slags and minerals. A review

    Xiao Yanping; Holappa, L.


    In this report, the thermodynamic properties of chromium bearing slags and minerals were reviewed based on the available information in the literature. It includes the analysing methods for oxidation state of chromium in slags, oxidation state of chromium and activities of chromium oxides in slags and minerals. The phase diagrams of chromium oxide systems and chromium distributions between slag and metal phases are also covered ill this review. Concerning the analysing methods, it was found that most of the available approaches are limited to iron free slag systems and the sample preparation is very sensitive to the analysing results. In silicate slags under reducing atmosphere, divalent and trivalent chromium co-exist in the slags. It is agreed that the fraction of divalent chromium to total chromium increases with higher temperature, lower slag basicity and oxygen potential. For the slags under oxidising atmosphere, trivalent, pentavalent and hexavalent states were reported to be stable. The activities of CrO and CrO{sub 1.5} were concluded to have positive deviation from ideal solution. Slag basicity has a positive effect and temperature has a negative effect on the activities of chromium oxides. The phase diagrams of the Cr-O, binary, and ternary chromium containing oxide systems have been examined systematically. The analysis shows that the data on the quaternary and quinary systems are insufficient, and require further investigation. The most important features of the chromium containing silicate slags are the large miscibility gaps and the stability of the chromite spinel. (orig.) (76 refs.)

  7. 21 CFR 73.1015 - Chromium-cobalt-aluminum oxide.


    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.1015 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1015 Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide is a blue-green pigment obtained by calcining...

  8. Hexavalent and trivalent chromium in leather: What should be done?

    Moretto, Angelo


    Trivalent chromium compounds are used for leather tanning, and chromium may be released during use of leather goods. In certain instances, small amounts of hexavalent chromium can be formed and released. Both trivalent and hexavalent chromium can elicit allergic skin reaction in chromium sensitised subjects, the latter being significantly more potent. Induction of sensitisation only occurs after exposure to hexavalent chromium. A minority of subjects are sensitised to chromium, and in a fraction of these subjects allergic skin reaction have been described after wearing leather shoes or, less frequently, other leather goods. The evidence that in all these cases the reaction is related to hexavalent chromium is not always strong. The content of hexavalent chromium in leather is regulated in European Union, but rate of release rather than content is relevant for allergic skin reaction. The role of trivalent chromium appear much less relevant if at all. Modern tanning procedure do not pose significant risk due to either hexavalent or trivalent chromium. Dismissing bad quality and worn-off leather goods is relevant in reducing or eliminating the skin reaction. It should also be pointed out that shoe components or substances other than chromium in leather may cause allergic/irritative skin reactions. PMID:26361854


    Toxicity studies regarding trivalent chromium have often been completed under conditions that are not designed to reflect conditions that would be encountered under normal physiological conditions. We have shown that the incorporation of chromium into tissues of rats from chromium chloride and chro...

  10. Strategies for chromium bioremediation of tannery effluent.

    Garg, Satyendra Kumar; Tripathi, Manikant; Srinath, Thiruneelakantan


    Bioremediation offers the possibility of using living organisms (bacteria, fungi, algae,or plants), but primarily microorganisms, to degrade or remove environmental contaminants, and transform them into nontoxic or less-toxic forms. The major advantages of bioremediation over conventional physicochemical and biological treatment methods include low cost, good efficiency, minimization of chemicals, reduced quantity of secondary sludge, regeneration of cell biomass, and the possibility of recover-ing pollutant metals. Leather industries, which extensively employ chromium compounds in the tanning process, discharge spent-chromium-laden effluent into nearby water bodies. Worldwide, chromium is known to be one of the most common inorganic contaminants of groundwater at pollutant hazardous sites. Hexavalent chromium poses a health risk to all forms of life. Bioremediation of chromium extant in tannery waste involves different strategies that include biosorption, bioaccumulation,bioreduction, and immobilization of biomaterial(s). Biosorption is a nondirected physiochemical interaction that occurs between metal species and the cellular components of biological species. It is metabolism-dependent when living biomass is employed, and metabolism-independent in dead cell biomass. Dead cell biomass is much more effective than living cell biomass at biosorping heavy metals, including chromium. Bioaccumulation is a metabolically active process in living organisms that works through adsorption, intracellular accumulation, and bioprecipitation mechanisms. In bioreduction processes, microorganisms alter the oxidation/reduction state of toxic metals through direct or indirect biological and chemical process(es).Bioreduction of Cr6+ to Cr3+ not only decreases the chromium toxicity to living organisms, but also helps precipitate chromium at a neutral pH for further physical removal,thus offering promise as a bioremediation strategy. However, biosorption, bioaccumulation, and

  11. Collisional properties of trapped cold chromium atoms

    Pavlovich, Z; Côté, R; Sadeghpour, H R; Pavlovic, Zoran; Roos, Bjoern O.; Côté, Robin


    We report on calculations of the elastic cross section and thermalization rate for collision between two maximally spin-polarized chromium atoms in the cold and ultracold regimes, relevant to buffer-gas and magneto-optical cooling of chromium atoms. We calculate ab initio potential energy curves for Cr2 and the van der Waals coefficient C6, and construct interaction potentials between two colliding Cr atoms. We explore the effect of shape resonances on elastic cross section, and find that they dramatically affect the thermalization rate. Our calculated value for the s-wave scattering length is compared in magnitude with a recent measurement at ultracold temperatures.

  12. Influence of nitrogen on the structure and properties of chromium, chromium-molybdenum and chromium-manganese steels

    Phase transformations, precipitation processes and properties of the chromium, chromium-molybdenum and chromium-manganese steels with a high content of nitrogen as the dependence on thermal treatment were investigated. In case of Fe-0.08C-18Cr-18Mn-N and Fe-0.08C-18Cr-18Mn-2Mo-N steels the samples in the state after solution at temperature 1050oC and 1150oC and 1250oC and after subsequent annealing in 600oC and 800oC were investigated. heat treatment of the Fe-0.5C-10Cr-N and Fe-0.5C-10Cr-1Mo-N steels included austenitizment from 1000oC with air cooling and hardening from 1000oC with oil cooling and tempering in 650oC and 750oC in two hours with cooling in the air. These investigations show that the influence of nitrogen as an alloy element on the phase transformations, precipitation processes, mechanical and corrosion properties is connected with the presence of molybdenum and chromium in the steel. Nitrogen with these elements creates complex ions with the coordinate number 6. This statement is formed on the base of both calculations and investigation results. (author)

  13. Electrodeposition of black chromium thin films from trivalent chromium-ionic liquid solution

    Eugénio, S.; Vilar, Rui; C. M. Rangel; Baskaran, I.


    In the present study, black chromium thin films were electrodeposited from a solution of 1-butyl-3- methylimidazolium tetrafluoroborate ([BMIm][BF4] ionic liquid containing trivalent chromium (Cr(III)). Homogeneous and well adherent coatings have been obtained on nickel, copper and stainless steel substrates. The nucleation and growth of the films were investigated by cyclic voltammetry and current-density/time transient techniques. SEM/EDS, XPS and XRD were used to study the morphology, chem...

  14. Reduction of Hexavalent Chromium by Viable Cells of Chromium Resistant Bacteria Isolated from Chromite Mining Environment

    Satarupa Dey; Baishali Pandit; A. K. Paul


    Environmental contamination of hexavalent chromium [Cr(VI)] is of serious concern for its toxicity as well as mutagenic and carcinogenic effects. Bacterial chromate reduction is a cost-effective technology for detoxification as well as removal of Cr(VI) from polluted environment. Chromium resistant and reducing bacteria, belonging to Arthrobacter, Pseudomonas, and Corynebacterium isolated from chromite mine overburden and seepage samples of Orissa, India, were found to tolerate 12–18 mM Cr(VI...

  15. Reduction of Chromium-VI by Chromium Resistant Lactobacilli: A Prospective Bacterium for Bioremediation

    Mishra, Ritesh; Sinha, Vartika; Kannan, Ambrose; Upreti, Raj K.


    Chromium is a toxic heavy metal, which primarily exists in two inorganic forms, Cr (VI) and Cr (III). Highly soluble hexavalent chromium is carcinogenic due to its oxidizing nature. It is well established that the intestinal bacteria including Lactobacilli have regulatory effect on intestinal homeostasis and a breakdown in the relationship between intestinal cells and bacteria results in the manifestation of gastrointestinal (GI) disorders. In this study Cr (VI) resistance was developed in La...

  16. Mechanical properties of metal-ceramic systems from nickel-chromium and cobalt-chromium alloys

    Mirković Nemanja


    Background/Aim. Metal-ceramic bond strength and alloys' elastic modulus clearly determine the potential of alloy application, because the ceramic integrity during mastication depends on these two characteristics. The aim of this study was to evaluate metal-ceramic bond strength and elastic modulus of cobalt-chromium alloys in making porcelainfused- to-metal restorations, regarding the application of the most frequent nickel-chromium alloy. Methods. The research was performed as an experimenta...

  17. Chromium-manganese steels of transition class

    Possibilities of nickel replacing by manganese and preparing the same level of mechanical properties as in chromium-nickel steels due to γ-α transformations taking place during property tests, are studied. Chromium-manganese steels with the composition of 0.05-0.1%C, 13-14%Cr, 5.0-6.5%Mn, 0.2-0.5%Si, 0.03-0.13%N, 0.05-0.01%Al and additionally alloyed 0.3-2.0%Cu, 0.05-0.6%V, 0.3-1.0%Mo, 0.02-0.05%Ca in various combinations have been melted. It is shown, that using alloying and heat treatment one can control the phase composition, austenite resistance to martensite transformation during loading and mechanical properties of chromium-manganese steels of the transition class. The use of the phase transformation in the process of testing determines the level of mechanical properties. The optimum development of the transformation accompanied by a sufficient development of processes of hardening and microstresses relaxation permits to obtain a high level of mechanical properties: σsub(B)=1500 MPa, σsub(0.2)-1130MPa, delta=15%, psi=37%, asub(H)=1000 kJ/msup(2) which exceeds the level for chromium-nickel steels. Steels have a lower cost and do not require any complecated heat treatment regime

  18. Defect structure of electrodeposited chromium layers

    Positron annihilation spectroscopy was applied to study the effects of pre-treatment and composition of substrates on the quality and defect structure of electrodeposited thick chromium coatings. The results show that both parameters are important, and a scenario is proposed why the mechanically polished substrate gives more defective film than the electro polished one.

  19. Defect structure of electrodeposited chromium layers

    Marek, T; Vertes, A; El-Sharif, M; McDougall, J; Chisolm, C U


    Positron annihilation spectroscopy was applied to study the effects of pre-treatment and composition of substrates on the quality and defect structure of electrodeposited thick chromium coatings. The results show that both parameters are important, and a scenario is proposed why the mechanically polished substrate gives more defective film than the electro polished one.

  20. Flashlamp-pumped lasing of chromium: GSGG

    Lasing action in chromium-doped gadolinium scandium gallium garnet (Cr:GSGG) is well established for both CW/sup (1)/ and flashlamp/sup (2)/ pumping. This paper describes an investigation of flashlamp-pumped Cr:GSGG lasers and indicates some of the factors which limit performance

  1. Trace Elements Excluding Iron - Chromium and Zinc

    The percentage of middle-aged US adults who are participating in leisure-time physical activities is growing. These adults also seek credible information about specific supplements that the public press routinely describes as necessary to enable increases in physical performance. Chromium and zinc a...


    The full document represents a comprehensive data base that considers all sources of chromium in the environment, the likelihood for its exposure to humans, and the possible consequences to man and lower organisms from its absorption. This information is integrated into a format ...

  3. 29 CFR 1926.1126 - Chromium (VI).


    ... CFR 1926.51 Where skin contact with chromium (VI) occurs, the employer shall provide washing facilities in conformance with 29 CFR 1926.51. Eating and drinking areas provided by the employer shall also... requirements of the Hazard Communication Standard, 29 CFR 1910.1200. (3) Cleaning and replacement. (i)...

  4. 29 CFR 1910.1026 - Chromium (VI).


    ... CFR 1910.141. Where skin contact with chromium (VI) occurs, the employer shall provide washing facilities in conformance with 29 CFR 1910.141. Eating and drinking areas provided by the employer shall also... requirements of the Hazard Communication Standard, 29 CFR 1910.1200. (3) Cleaning and replacement. (i)...

  5. 29 CFR 1915.1026 - Chromium (VI).


    ... CFR 1910.141. Where skin contact with chromium (VI) occurs, the employer shall provide washing facilities in conformance with 29 CFR 1915.97. Eating and drinking areas provided by the employer shall also... requirements of the Hazard Communication Standard, 29 CFR 1910.1200. (3) Cleaning and replacement. (i)...

  6. Chromium(III) and chromium(VI) surface treated galvanized steel for outdoor constructions: environmental aspects.

    Lindström, David; Hedberg, Yolanda; Odnevall Wallinder, Inger


    The long-term degradation of chromium(III) (Zn-Cr(III)) and chromium(VI)-based (Zn-Cr(VI)) surface treatments on galvanized steel and their capacities to hinder the release of zinc induced by atmospheric corrosion at nonsheltered urban and marine exposure conditions for 2 years are investigated. Compared to bare zinc sheet, both surface treatments revealed high corrosion protection abilities and capacities to hinder the release of zinc, still evident after 2 years of exposure. The zinc barrier properties of the thinner Zn-Cr(VI) (10 nm) treatment were during the first 100 days of urban exposure slightly improved compared with Zn-Cr(III) (35 nm). However, their long-term protection capacities were inverse. Released concentrations of total chromium correspond to annual release rates less than 0.000032 (Zn-Cr(III)) and 0.00014 g Cr m(-2) yr(-1) (Zn-Cr(VI)) after 1 year of urban exposure. Aging by indoor storage of the surface treatments prior to outdoor exposure reduced the released Cr concentrations from the surface treatments. No Cr(VI) was released from the aged surfaces but from the freshly exposed Zn-Cr(VI). Marine exposure conditions resulted in a faster reduction of chromate to chromium(III)oxide compared with urban conditions, and a significantly lower amount of both chromium(III) and chromium(VI) released from Zn-Cr(VI) at the marine site compared with the urban site. PMID:20462267

  7. Biological groundwater treatment for chromium removal at low hexavalent chromium concentrations.

    Mamais, Daniel; Noutsopoulos, Constantinos; Kavallari, Ioanna; Nyktari, Eleni; Kaldis, Apostolos; Panousi, Eleni; Nikitopoulos, George; Antoniou, Kornilia; Nasioka, Maria


    The objective of this work is to develop and evaluate biological groundwater treatment systems that will achieve hexavalent chromium reduction and total chromium removal from groundwater at hexavalent chromium (Cr(VI)) groundwater concentrations in the 0-200 μg/L range. Three lab-scale units operated, as sequencing batch reactors (SBR) under aerobic, anaerobic and anaerobic-aerobic conditions. All systems received groundwater with a Cr(VI) content of 200 μg/L. In order to support biological growth, groundwater was supplemented with milk, liquid cheese whey or a mixture of sugar and milk to achieve a COD concentration of 200 mg/L. The results demonstrate that a fully anaerobic system or an anaerobic-aerobic system dosed with simple or complex external organic carbon sources can lead to practically complete Cr(VI) reduction to Cr(III). The temperature dependency of maximum Cr(VI) removal rates can be described by the Arrhenius relationship. Total chromium removal in the biological treatment systems was not complete because a significant portion of Cr(III) remained in solution. An integrated system comprising of an anaerobic SBR followed by a sand filter achieved more than 95% total chromium removal thus resulting in average effluent total and dissolved chromium concentrations of 7 μg/L and 3 μg/L, respectively. PMID:26971177

  8. Nephrotoxic and hepatotoxic effects of chromium compounds in rats

    Laborda, R.; Diaz-Mayans, J.; Nunez, A.


    The nephrotoxic, hepatotoxic and cardiotoxic actions of hexavalent chromium compounds, as well as their effects on lung, blood and circulation may contribute to the fatal outcome of chromium intoxication. Although trivalent chromium have been regarded as relatively biologically inert, there are a few salts of chromium III that have been found to be carcinogenic when inhaled, ingested or brought in contact with the tissues. Sensitive persons and industry workers have been subjects of dermatitis, respiratory tract injuries and digestive ulcers due to chromium compounds. In this work, the authors have studied the effect of trivalent and hexavalent chromium compounds on rats measuring the transaminases (GOT and GPT), urea and creatinine levels in serum of chromium poisoned animals at different times.

  9. A Kinetic Model of Chromium in a Flame


    Chromium has been identified as a carcinogenic metal.Incineration is the useful method for disposal of toxic chromium hazard waste and a chromium kinetic model in a flame is very important to study chromium oxidation.Chromium chemical kinetics over a range of temperatures of a hydrogen/air flame is proposed.Nine chromium compounds and fifty-eight reversible chemical reactions were considered The forward reaction rates are calculated based on the molecular collision approach for unknown ones and Arrhenius's Law for known ones.The backward reaction rates were calculated according to forward reaction rates, the equilibrium constants and chemical thermodynamics.It is verified by several equilibrium cases and is tested by a hydrogen/air diffusion flame.The results show that the kinetic model could be used in cases in which the chromium kinetics play an important role in a flame

  10. The Chromium is an essential element in the human

    The Chromium is an essential element for human and animals, because it a preponderant function in the insulin metabolism as a glucose tolerance factor (GTF). The deficiency of chromium engenders a deterioration in the glucose metabolism due to bad efficiency of insulin. Because the importance of this element an exhaustive reference review was made and this presents some studies realized in laboratory animals and in human beings where it is prove with resuits the effect of chromium over the improvement of patients with non-insulin dependant diabetes. Three substances are presented as chromium active biological forms: a material rich in chromium known as glucose tolerance factor, chromium picolinate and a substance of low molecular weight LMWCr in its forms of apo and holo that contains chromium and it links the insulin receptor and improves its activity. Also this paper presents information about the condition of diabetes in Costa Rica. (Author)

  11. Reaction of chromium(VI) with glutathione or with hydrogen peroxide: identification of reactive intermediates and their role in chromium(VI)-induced DNA damage.

    Aiyar, J; Berkovits, H J; Floyd, R A; Wetterhahn, K E


    The types of reactive intermediates generated upon reduction of chromium(VI) by glutathione or hydrogen peroxide and the resulting DNA damage have been determined. In vitro, reaction of chromium(VI) with glutathione led to formation of two chromium(V) complexes and the glutathione thiyl radical. When chromium(VI) was reacted with DNA in the presence of glutathione, chromium-DNA adducts were obtained, with no DNA strand breakage. The level of chromium-DNA adduct formation correlated with chrom...

  12. Design and performance of chromium mist generator

    Tirgar Aram


    Full Text Available Chromium mist generator is an essential tool for conducting researches and making science-based recommendations to evaluate air pollution and its control systems. The purpose of this research was to design and construct a homogenous chromium mist generator and the study of some effective factors including sampling height and distances between samplers in side-by-side sampling on chromium mist sampling method. A mist generator was constructed, using a chromium electroplating bath in pilot scale. Concentration of CrO3 and sulfuric acid in plating solution was 125 g L-1 and 1.25 g L-1, respectively. In order to create permanent air sampling locations, a Plexiglas cylindrical chamber (75 cm height, 55 cm i.d was installed the bath overhead. Sixty holes were produced on the chamber in 3 rows (each 20. The distance between rows and holes was 15 and 7.5 cm, respectively. Homogeneity and effective factors were studied via side-by-side air sampling method. So, 48 clusters of samples were collected on polyvinyl chloride (PVC filters housed in sampling cassettes. Cassettes were located in 35, 50, and 65 cm above the solution surface with less than 7.5 and/or 7.5-15 cm distance between heads. All samples were analyzed according to the NIOSH method 7600. According to the ANOVA test, no significant differences were observed between different sampling locations in side-by-side sampling (P=0.82 and between sampling heights and different samplers distances (P=0.86 and 0.86, respectively. However, there were notable differences between means of coefficient of variations (CV in various heights and distances. It is concluded that the most chromium mist homogeneity could be obtained at height 50 cm from the bath solution surface and samplers distance of < 7.5 cm.

  13. Biodistribution of /sup 59/Fe-thiosemicarbazones

    Hanson, R.N.; Davis, M.A.


    The /sup 59/Fe-iron(II) chelates of 2-formylpyridine thiosemicarbazone (I), 5-dimethylamino-2-formylpyridine thiosemicarbazone (II), and 5-hydroxy-2-formylpyridine thiosemicarbazone (III) were prepared and their biodistribution determined in normal rats. Early accumulation of these complexes occurred in the liver, muscle and pelt with lesser amounts in the blood, kidneys and other organs. The tissue levels decreased with a 1 to 2-h half-life with the exception of the liver and intestines. The liver level tended to remain constant over the 2-h period. Accumulation in the gut resulting from hepatobiliary excretion increased over the first 60 min and then leveled off. In rats bearing a subcutaneous glioblastoma the uptake of compound I increased during the first 24 h after administration, and tumor to normal tissue ratios of 2 to 3.3 were obtained.

  14. Chromium supplementation improved post-stroke brain infarction and hyperglycemia.

    Chen, Wen-Ying; Mao, Frank Chiahung; Liu, Chia-Hsin; Kuan, Yu-Hsiang; Lai, Nai-Wei; Wu, Chih-Cheng; Chen, Chun-Jung


    Hyperglycemia is common after acute stroke and is associated with a worse outcome of stroke. Thus, a better understanding of stress hyperglycemia is helpful to the prevention and therapeutic treatment of stroke. Chromium is an essential nutrient required for optimal insulin activity and normal carbohydrate and lipid metabolism. Beyond its nutritional effects, dietary supplement of chromium causes beneficial outcomes against several diseases, in particular diabetes-associated complications. In this study, we investigated whether post-stroke hyperglycemia involved chromium dynamic mobilization in a rat model of permanent focal cerebral ischemia and whether dietary supplement of chromium improved post-stroke injury and alterations. Stroke rats developed brain infarction, hyperglycemia, hyperinsulinemia, glucose intolerance, and insulin resistance. Post-stroke hyperglycemia was accompanied by elevated secretion of counter-regulatory hormones including glucagon, corticosterone, and norepinephrine, decreased insulin signaling in skeletal muscles, and increased hepatic gluconeogenesis. Correlation studies revealed that counter-regulatory hormone secretion showed a positive correlation with chromium loss and blood glucose increased together with chromium loss. Daily chromium supplementation increased tissue chromium levels, attenuated brain infarction, improved hyperglycemia, and decreased plasma levels of glucagon and corticosterone in stroke rats. Our findings suggest that stroke rats show disturbance of tissue chromium homeostasis with a net loss through urinary excretion and chromium mobilization and loss might be an alternative mechanism responsible for post-stroke hyperglycemia. PMID:26477944

  15. Femtosecond laser surface structuring and oxidation of chromium thin coatings: Black chromium

    Kotsedi, L., E-mail: [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Nuru, Z.Y. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Mthunzi, P. [National Laser Centre, Council for Scientific and Industrial Research, 0001 Pretoria (South Africa); Muller, T.F.G. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Eaton, S.M. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Julies, B. [University of the Western Cape, Physics Department, Bellville, 7535 Cape Town (South Africa); Manikandan, E. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa); Ramponi, R. [Physics Department, Politecnico di Milano, Piazza Leonardo Da Vinci, 32, 20133 Milano (Italy); Maaza, M. [UNESCO-UNISA Africa Chair in Nanosciences-Nanotechnology, College of Graduate Studies, University of South Africa, Muckleneuk Ridge, P.O. Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), iThemba LABS-National Research Foundation, 1 Old Faure Road, Somerset West 7129, P.O. Box 722, Somerset West, Western Cape (South Africa)


    Highlights: • Oxidation of the chromium thin film to chromium oxide by femtosecond laser with a fundamental wavelength of 1064 nm. • Solar absorber from chromium oxide that low percentage reflectance. • Femtosecond laser oxidation, with a de-focused laser. • Chromium oxide formation by femtosecond laser in normal ambient. - Abstract: In view of their potential applications as selective solar absorbers, chromium coatings on float glass substrates were nano/micro structured by femtosecond laser in air. Raman and X-rays diffraction investigations confirmed the formation of an ultra-porous α-Cr{sub 2}O{sub 3} layer at the surface; higher is the input laser power, enhanced is the crystallinity of the α-Cr{sub 2}O{sub 3} layer. The α-Cr{sub 2}O{sub 3} layer with the Cr underneath it in addition to the photo-induced porosity acted as a classical ceramic–metal nano-composite making the reflectance to decrease significantly within the spectral range of 190–1100 nm. The average reflectance decreased from 70 to 2%.

  16. Femtosecond laser surface structuring and oxidation of chromium thin coatings: Black chromium

    Highlights: • Oxidation of the chromium thin film to chromium oxide by femtosecond laser with a fundamental wavelength of 1064 nm. • Solar absorber from chromium oxide that low percentage reflectance. • Femtosecond laser oxidation, with a de-focused laser. • Chromium oxide formation by femtosecond laser in normal ambient. - Abstract: In view of their potential applications as selective solar absorbers, chromium coatings on float glass substrates were nano/micro structured by femtosecond laser in air. Raman and X-rays diffraction investigations confirmed the formation of an ultra-porous α-Cr2O3 layer at the surface; higher is the input laser power, enhanced is the crystallinity of the α-Cr2O3 layer. The α-Cr2O3 layer with the Cr underneath it in addition to the photo-induced porosity acted as a classical ceramic–metal nano-composite making the reflectance to decrease significantly within the spectral range of 190–1100 nm. The average reflectance decreased from 70 to 2%

  17. Production of basic chromium sulfate by using recovered chromium from ashes of thermally treated leather.

    Dettmer, Aline; Nunes, Keila Guerra Pacheco; Gutterres, Mariliz; Marcílio, Nilson Romeu


    Leather wastes tanned with chromium are generated during the production process of leather, hence the wastes from hand crafted goods and footwear industries are a serious environmental problem. The thermal treatment of leather wastes can be one of the treatment options because the wastes are rich in chromium and can be used as a raw material for sodium chromate production and further to obtain several chromium compounds. The objective of this study was to utilize the chromium from leather wastes via basic chromium sulfate production to be subsequently applied in a hide tanning. The obtained results have shown that this is the first successful attempt to achieve desired base properties of the product. The result was achieved when the following conditions were applied: a molar ratio between sodium sulfite and sodium dichromate equal to 6; reaction time equal to 5 min before addition of sulfuric acid; pH of sodium dichromate solution equal to 2. Summarizing, there is an opportunity to utilize the dangerous wastes and reused them in the production scheme by minimizing or annulling the environmental impact and to attend a sustainable process development concept. PMID:20031309

  18. In patients with HIV-infection, chromium supplementation improves insulin resistance and other metabolic abnormalities: a randomized, double-blind, placebo controlled trial.

    Aghdassi, Elaheh; Arendt, Bianca M; Salit, Irving E; Mohammed, Saira S; Jalali, Pegah; Bondar, Helena; Allard, Johane P


    Chromium is an essential micronutrient; chromium deficiency has been reported to cause insulin resistance, hyperglycemia and hyperlipidemia. The aim was to investigate the effect of chromium supplementation on insulin-resistance, other metabolic abnormalities, and body composition in people living with HIV. This was a randomized, double-blind, placebo-controlled trial. Fifty-two HIV-positive subjects with elevated glucose, lipids, or evidence of body fat redistribution, and who had insulin-resistance based on the calculation of homeostasis model of assessment (HOMA-IR > or = 2.5) were assessed. Subjects who were on insulin or hypoglycemic medications were excluded. Subjects were randomized to receive either 400 microg/day chromium-nicotinate or placebo for 16 weeks. Forty-six subjects, 23 in each group, completed the study. Fasting blood insulin, glucose, lipid profile and body composition were measured before and after intervention. Chromium was tolerated without side effects and resulted in a significant decrease in HOMA-IR (median (IQR) (pre:4.09 (3.02-8.79); post: 3.66 (2.40-5.46), p=0.004), insulin (pre: 102 (85-226); post: 99 (59-131) pmol/L, p=0.003), triglycerides, total body fat mass (mean+/-SEM) (pre: 17.3+/-1.7; post: 16.3+/-1.7 kg; p=0.002) and trunk fat mass (pre: 23.8+/-1.9; post: 22.7+/-2.0 %; p=0.008). Blood glucose, C-peptide, total, HDL and LDL cholesterol, and hemoglobin A1c remained unchanged. Biochemical parameters did not change in the placebo group except for LDL cholesterol which increased significantly. Body weight and medication profile remained stable throughout the study for both groups. In summary, chromium improved insulin resistance, metabolic abnormalities, and body composition in HIV+ patients. This suggests that chromium supplements alleviate some of the antiretroviral-associated metabolic abnormalities. PMID:20163347

  19. 21 CFR 7.59 - General industry guidance.


    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false General industry guidance. 7.59 Section 7.59 Food... POLICY Recalls (Including Product Corrections)-Guidance on Policy, Procedures, and Industry Responsibilities § 7.59 General industry guidance. A recall can be disruptive of a firm's operation and...

  20. 29 CFR 531.59 - The tip wage credit.


    ... 29 Labor 3 2010-07-01 2010-07-01 false The tip wage credit. 531.59 Section 531.59 Labor... § 531.59 The tip wage credit. In determining compliance with the wage payment requirements of the Act... such employee in the workweek for which the wage payment is made. This credit is in addition to...

  1. 40 CFR 59.509 - Can I get a variance?


    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Can I get a variance? 59.509 Section 59... Volatile Organic Compound Emission Standards for Aerosol Coatings § 59.509 Can I get a variance? (a) Any... its reasonable control may apply in writing to the Administrator for a temporary variance....

  2. 25 CFR 141.59 - Customer complaint procedures.


    ... 25 Indians 1 2010-04-01 2010-04-01 false Customer complaint procedures. 141.59 Section 141.59... THE NAVAJO, HOPI AND ZUNI RESERVATIONS Enforcement Powers, Procedures and Remedies § 141.59 Customer complaint procedures. (a) Any customer of a licensee may file a complaint with the Commissioner...

  3. 29 CFR 4003.59 - Decision by the Appeals Board.


    ... of the facts or legal conclusions supporting the decision, and state that the appellant has exhausted... 29 Labor 9 2010-07-01 2010-07-01 false Decision by the Appeals Board. 4003.59 Section 4003.59... ADMINISTRATIVE REVIEW OF AGENCY DECISIONS Administrative Appeals § 4003.59 Decision by the Appeals Board. (a)...

  4. 33 CFR 173.59 - Where to submit report.


    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Where to submit report. 173.59 Section 173.59 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED....59 Where to submit report. A report required by § 173.55 must be submitted to: (a) The...

  5. 46 CFR 64.59 - Spring loaded pressure relief valve.


    ... 46 Shipping 2 2010-10-01 2010-10-01 false Spring loaded pressure relief valve. 64.59 Section 64.59... AND CARGO HANDLING SYSTEMS Pressure Relief Devices and Vacuum Relief Devices for MPTs § 64.59 Spring loaded pressure relief valve. A spring loaded pressure relief valve must— (a) Be set at a...

  6. 46 CFR 111.59-3 - No mechanical cooling.


    ... 46 Shipping 4 2010-10-01 2010-10-01 false No mechanical cooling. 111.59-3 Section 111.59-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Busways § 111.59-3 No mechanical cooling. A busway must not need mechanical...

  7. 49 CFR 236.59 - Insulated rail joints.


    ... 49 Transportation 4 2010-10-01 2010-10-01 false Insulated rail joints. 236.59 Section 236.59..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.59 Insulated rail joints. Insulated rail joints shall be...

  8. 46 CFR 59.10-30 - Seal welding.


    ... 46 Shipping 2 2010-10-01 2010-10-01 false Seal welding. 59.10-30 Section 59.10-30 Shipping COAST... VESSELS AND APPURTENANCES Welding Repairs to Boilers and Pressure Vessels in -Service § 59.10-30 Seal welding. Where leaks occur in riveted joints or connections, they shall be carefully investigated...

  9. 14 CFR 1260.59 - Choice of law.


    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Choice of law. 1260.59 Section 1260.59... Special Conditions § 1260.59 Choice of law. Choice of Law October 2000 The rights and obligations of the parties to the grant (or cooperative agreement) shall be ascertainable by recourse to the laws of...

  10. 42 CFR 59.8 - How is a grant awarded?


    ... 42 Public Health 1 2010-10-01 2010-10-01 false How is a grant awarded? 59.8 Section 59.8 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS GRANTS FOR FAMILY PLANNING SERVICES Project Grants for Family Planning Services § 59.8 How is a grant awarded? (a) The notice of...

  11. Inelastic Scattering of Neutrons in Chromium

    The phonon spectrum of chromium has been studied by neutron inelastic scattering. The dispersion curves are very similar, in form to those of tungsten and molybdenum, indicating similar interionic force constants. The neutron groups broaden but do not shift appreciably when the temperature is raised. No effect has been observed which can be attributed to the interaction between the phonons and the crystal magnetization in the antiferromagnetic phase. (author)

  12. Observational Approach to Chromium Site Remediation - 13266

    Production reactors at the U.S. Department of Energy's (DOE) Hanford Site in Richland, Washington, required massive quantities of water for reactor cooling and material processing. To reduce corrosion and the build-up of scale in pipelines and cooling systems, sodium dichromate was added to the water feedstock. Spills and other releases at the makeup facilities, as well as leaks from miles of pipelines, have led to numerous areas with chromium-contaminated soil and groundwater, threatening fish populations in the nearby Columbia River. Pump-and-treat systems have been installed to remove chromium from the groundwater, but significant contamination remain in the soil column and poses a continuing threat to groundwater and the Columbia River. Washington Closure Hanford, DOE, and regulators are working on a team approach that implements the observational approach, a strategy for effectively dealing with the uncertainties inherent in subsurface conditions. Remediation of large, complex waste sites at a federal facility is a daunting effort. It is particularly difficult to perform the work in an environment of rapid response to changing field and contamination conditions. The observational approach, developed by geotechnical engineers to accommodate the inherent uncertainties in subsurface conditions, is a powerful and appropriate method for site remediation. It offers a structured means of quickly moving into full remediation and responding to the variations and changing conditions inherent in waste site cleanups. A number of significant factors, however, complicate the application of the observational approach for chromium site remediation. Conceptual models of contamination and site conditions are difficult to establish and get consensus on. Mid-stream revisions to the design of large excavations are time-consuming and costly. And regulatory constraints and contract performance incentives can be impediments to the flexible responses required under the observational

  13. Stainless chromium-nickel steels. Chapter I

    The chemical composition is tabulated of 90 chromium-nickel stainless steels and alloys given in volume %. The values are also given of the corrosion resistance of the steels and alloys. The tables show data on the surface condition or the methods of material working, types and chemical composition of the medium where corrosion resistance tests were carried out, temperature, pressure, time of tests, corrosion rates, corrosion types, and literature references. A total of 35 references is given. (J.B.)

  14. Loading chromium atoms in a magnetic guide

    Greiner, A; Sebastian, J.; Rehme, P.; Aghajani-Talesh, A.; Griesmaier, A.; Pfau, T.


    We have realized a magnetic guide for ultracold chromium atoms by continuously loading atoms directly from a Zeeman slower into a horizontal guide. We observe an atomic flux of $2 \\cdot 10^7$ atoms/s and are able to control the mean velocity of the guided atoms between 0 m/s and 3 m/s. We present our experimental results on loading and controlling the mean velocity of the guided atoms and discuss the experimental techniques that are used.

  15. X-616 Chromium Sludge Lagoons pictorial overview, Piketon, Ohio

    The Portsmouth Gaseous Diffusion Plant uses large quantities of water for process cooling. The X-616 Liquid Effluent Control Facility was placed in operation in December 1976 to treat recirculation cooling water blowdown from the process cooling system. A chromium-based corrosion inhibitor was used in the cooling water system. A chromium sludge was produced in a clarifier to control chromium levels in the water. Chromium sludge produced by this process was stored in two surface impoundments called the X-616 Chromium Sludge Lagoons. The sludge was toxic due to its chromium concentration and therefore required treatment. The sludge was treated, turning it into a sanitary waste, and buried in an Ohio EPA approved landfill. The plant's process cooling water system has changed to a more environmentally acceptable phosphate-based inhibitor. Closure activities at X-616 began in August 1990, with all construction activities completed in June 1991, at a total cost of $8.0 million

  16. Chromium oxidation state mapping in human cells

    Ortega, R.; Fayard, B.; Salomé, M.; Devès, G.; Susini, J.


    The widespread use of chromium in industrial applications such as chemical production of pigments, refractory brick production, tanning, metallurgy, electroplating, and combustion of fuels has lead to human occupational exposure and to its increased introduction into the environment. Hexavalent chromium compounds are established carcinogens but their mechanism of cell transformation is not known. Up to now, no microanalytical technique was sensitive enough to allow the observation of chromium distribution, and oxidation state identification, within isolated cells at carcinogenic concentrations. In this experiment, we used successfully the ID-21 X-ray microscope to map Cr(VI) and total Cr distributions in cells exposed in vitro to soluble, and insoluble, Cr(VI) compounds. Exposure to soluble compounds, weak carcinogens, resulted in a homogeneous intracellular distribution of Cr, confirming by in situ measurement that Cr is present in the cell nucleus. Cr(VI) was never detected in cells which suggests a mechanism of rapid intracellular reducticn. On the other hand, exposure to insoluble compounds, strong carcinogens, also resulted in a homogeneous distribution of reduced forms of Cr in cells, and their nucleus. However, in this case, Cr(VI)-rich structures were observed into the cells suggesting that carcinogenicity is enhanced when oxidation reactions due to Cr(VI) chronic exposure are associated to Cr-DNA alterations.

  17. Dimensionally Controlled Lithiation of Chromium Oxide

    Fister, Tim T. [Argonne National Lab. (ANL), Argonne, IL (United States); Hu, Xianyi [Northwestern Univ., Evanston, IL (United States); Esbenshade, Jennifer [Univ. of Illinois, Urbana-Champaign, IL (United States); Chen, Xiao [Northwestern Univ., Evanston, IL (United States); Wu, Jinsong [Northwestern Univ., Evanston, IL (United States); Dravid, Vinayak [Northwestern Univ., Evanston, IL (United States); Bedzyk, Michael [Northwestern Univ., Evanston, IL (United States); Long, Brandon [Argonne National Lab. (ANL), Argonne, IL (United States); Gewirth, Andrew A. [Univ. of Illinois, Urbana-Champaign, IL (United States); Shi, Bing [Argonne National Lab. (ANL), Argonne, IL (United States); Schlepütz, Christian M. [Argonne National Lab. (ANL), Argonne, IL (United States); Fenter, Paul [Argonne National Lab. (ANL), Argonne, IL (United States)


    Oxide conversion reactions are an alternative approach for high capacity lithium ion batteries but are known to suffer from structural irreversibility associated with the phase separation and reconstitution of reduced metal species and Li2O. In particular, the morphology of the reduced metal species is thought to play a critical role in the electrochemical properties of a conversion material. Here we use a model electrode with alternating layers of chromium and chromium oxide to better understand and control these phase changes in real-time and at molecular length scales. Despite lacking crystallinity at the atomic scale, this superstructure is observed (with X-ray reflectivity, XR) to lithiate and delithiate in a purely one-dimensional manner, preserving the layered structure. The XR data show that the metal layers act as nucleation sites for the reduction of chromium in the conversion reaction. Irreversibility during delithiation is due to the formation of a ternary phase, LiCrO2, which can be further delithiated at higher potentials. The results reveal that the combination of confining lithiation to nanoscale sheets of Li2O and the availability of reaction sites in the metal layers in the layered structure is a strategy for improving the reversibility and mass transport properties that can be used in a wide range of conversion materials.

  18. Chromium--a material for fusion technology

    Due to their low neutron-induced radioactivity chromium based materials are considered to be candidates for structure materials in fusion technology. In this paper investigations are presented of unirradiated chromium with a purity of 99.96% (DUCROPUR) and a dispersion strengthened chromium alloy Cr5Fe1Y2O3 (DUCROLLOY). Both materials have been produced in a powder metallurgical route. Mechanical tests of smooth and pre-cracked specimens have been performed in a wide temperature range. Below 280 deg. C the fracture toughness values of DUCROPUR are very low (1/2), above the transition temperature they exceed 500 MPa m1/2. Large plastic deformations have been observed. DUCROLLOY does not indicate such a significant increase of fracture toughness in the tested temperature range. But above 400 deg. C large plastic deformations can be obtained in bending samples, too. The fatigue crack propagation behaviour of DUCROPUR at 300 deg. C is similar to that of a ductile metal


    Inga Zinicovscaia


    Due to its widespread industrial use, chromium has become a serious pollutant in diverse environmental settings. The main source of chromium pollution including the Republic o Moldova is industry. It is a great need to develop new eco-friendly methods of chromium removal. Biosorption of heavy metals is a most promising technology involved in the removal of toxic metals from industrial waste streams and natural waters. This article is an extended abstract of a communication presented at the...


    A. Chidambaram ، P. Sundaramoorthy ، A. Murugan ، K. Sankar Ganesh ، L. Baskaran


    Chromium is known to be highly toxic to biological systems. This study was designed to determine the mutagenic effects of different concentrations (0, 10, 25, 50, 100 and 200 mg/L) of hexavalent chromium on root tip cells of blackgram (Vigna mungo L. Hepper). The blackgram seeds were equi-spacially arranged in sterilized petriplates lined with filter paper and they were treated with different concentrations of chromium solution. In germination studies, the morphological growth parameters such...

  1. Processes affecting the remediation of chromium-contaminated sites.

    Palmer, C.D.; Wittbrodt, P R


    The remediation of chromium-contaminated sites requires knowledge of the processes that control the migration and transformation of chromium. Advection, dispersion, and diffusion are physical processes affecting the rate at which contaminants can migrate in the subsurface. Heterogeneity is an important factor that affects the contribution of each of these mechanisms to the migration of chromium-laden waters. Redox reactions, chemical speciation, adsorption/desorption phenomena, and precipitat...

  2. Analysis of molybdenum, chromium, vanadium and iron by polarographic techniques

    The application of direct current Tast polarograph, differential pulse polarography and phase-selective alternative current Tast polarography to the problem of determining molybdenum, chromium, vanadium and iron in various supporting electrolytes is reported. The effect of the supporting electrolyte on the wave/peak potential and sensitivity of the metal ion have been examined. The polarographic methods were applied for simultaneous determination of chromium (3)/chromium (6), vanadium (4), vanadium (5) and iron (2)/iron (3) in different supporting electrolytes

  3. Production of a chromium Bose-Einstein condensate

    Griesmaier, Axel; Stuhler, Jürgen; Pfau, Tilman


    The recent achievement of Bose-Einstein condensation of chromium atoms [1] has opened longed-for experimental access to a degenerate quantum gas with long-range and anisotropic interaction. Due to the large magnetic moment of chromium atoms of 6 {$\\mu$}B, in contrast to other Bose- Einstein condensates (BECs), magnetic dipole-dipole interaction plays an important role in a chromium BEC. Many new physical properties of degenerate gases arising from these magnetic forces have been predicted in ...

  4. Removal of chromium(VI) from saline wastewaters by

    AKSU, Zümriye


    Some industrial wastewaters contain higher quantities of salts besides chromium(VI) ions so the effect of these salts on the biosorption of chromium(VI) should be investigated. The biosorption of chromium (VI) from saline solutions on two strains of living Dunaliella algae were tested under laboratory conditions as a function of pH, initial metal ion and salt (NaCl) concentrations in a batch system. The biosorption capacity of both Dunaliella strains strongly de...

  5. Increase of chromium utilization in stainless steel melting

    The processes of deoxidizing when melting stainless 18-10 steels in electric are furnaces by the method of remelting with wastes are investigated. The dependences of amount of reduced chromium on silicon consumption are made more precise. It is shown that it is useful to apply aluminium for deoxidation of acid high-chromium slags. Based on the data on pilot melts the extent to which aluminium can be used as a reducing agent for chromium is estimated. 3 refs., 2 figs

  6. Scientific Opinion on ChromoPrecise® cellular bound chromium yeast added for nutritional purposes as a source of chromium in food supplements and the bioavailability of chromium from this source

    EFSA Panel on Food Additives and Nutrient Sources added to Food (ANS)


    The Panel on Food Additives and Nutrient Sources added to Food (ANS) provides a scientific opinion re-evaluating the safety of ChromoPrecise® cellular bound chromium yeast added for nutritional purposes as a source of chromium in food supplements and the bioavailability of chromium from this source. ChromoPrecise® is a yeast preparation with an enriched trivalent chromium content, obtained by culture of Saccharomyces cerevisiae in the presence of chromium chloride. A daily intake of 100 µg ch...

  7. Chromium depletion from stainless steels during vacuum annealing

    The behaviour of chromium during selective evaporation by high temperature vacuum annealing has been investigated by means of energy dispersive X-ray analysis and by neutron activation analysis. It was established that the rate of chromium loss from austenitic stainless steels 316 and 321 is controlled by chromium inter-diffusion rather than tracer diffusion in the alloy. Two important parameters in selective removal of chromium from alloy steels are the variation in the chromium surface concentration with time and the depletion profile in the alloy. The present work gives support for the model in which loss of chromium is dependent on its diffusivity in the alloy and on an interface transfer coefficient. The results showed that the surface concentration of chromium decreased with increasing vacuum annealing time. The chromium depletion profile in the metal was in accord with the previous derived model, apart from an anomalous near surface region. Here the higher resolution of a neutron activation technique indicated a region within approximately 2 microns of the surface where the chromium concentration decreased more steeply than expected. (author)

  8. Stabilization and solidification of chromium-contaminated soil

    Cherne, C.A.; Thomson, B.M. [Univ. of New Mexico, Albuquerque, NM (United States). Civil Engineering Dept.; Conway, R. [Sandia National Labs., Albuquerque, NM (United States)


    Chromium-contaminated soil is a common environmental problem in the United States as a result of numerous industrial processes involving chromium. Hexavalent chromium [Cr(VI)] is the species of most concern because of its toxicity and mobility in groundwater. One method of diminishing the environmental impact of chromium is to reduce it to a trivalent oxidation state [Cr(III)], in which it is relatively insoluble and nontoxic. This study investigated a stabilization and solidification process to minimize the chromium concentration in the Toxicity Characteristic Leaching Procedure (TCLP) extract and to produce a solidified waste form with a compressive strength in the range of 150 to 300 pounds per square inch (psi). To minimize the chromium in the TCLP extract, the chromium had to be reduced to the trivalent oxidation state. The average used in this study was an alluvium contaminated with chromic and sulfuric acid solutions. The chromium concentration in the in the in situ soil was 1212 milligrams per kilogram (mg/kg) total chromium and 275 mg/kg Cr(VI). The effectiveness of iron, ferrous sulfate to reduce Cr(VI) was tested in batch experiments.

  9. Method of trivalent chromium concentration determination by atomic spectrometry

    Reheulishvili, Aleksandre N.; Tsibakhashvili, Neli Ya.


    A method is disclosed for determining the concentration of trivalent chromium Cr(III) in a sample. The addition of perchloric acid has been found to increase the atomic chromium spectrometric signal due to Cr(III), while leaving the signal due to hexavalent chromium Cr(VI) unchanged. This enables determination of the Cr(III) concentration without pre-concentration or pre-separation from chromium of other valences. The Cr(III) concentration may be measured using atomic absorption spectrometry, atomic emission spectrometry or atomic fluorescence spectrometry.

  10. Tribological Characteristics of Chromium-active Carbon Electroplated Composite Coatings

    GUKa-fi; HUAMeng; Yi-min


    A process of chromium electroplating using a standard bath with additives and active carbon particles was reported, and the tribological behaviors of the composite coatings using the pin-on-disk tester and the table wear tester were i nvestig(aed. Experimental results indicate that the electroplated chromium-active carbon composite coatings exhibited the low friction coefficient anti excellent anti-wear properties whets coffered with the normal chromium electroplated ones. The formation of active carbon particles within the chromium matrices can be explained by SEM analysis and the mechanis of wear resistance of the composite coatings were studied.

  11. Defect transformation in GSGG crystals during chromium ion activation

    Absorption and induced absorption spectra, dose dependence of induced absorption, thermoluminescence of GSGG crystals, nominally pure and activated with chromium and neodymium ions in different concentrations, are investigated. It is shown that it is chromium ion presence in large concentration that decreases the induced coloration in GSGG crystals after γ-irradiation at 300 K. Optimum concentration of chromium ions for the minimum of induced coloration are found. The mechanism of decrease of induced coloration consisting in Fermi level displacement by chromium ion activation is established. Defect concentration and localization and recombination possibilities of electrons and holes in GSGG crystals are estimated by computer simulation

  12. Oral bioavailability of chromium from a specific site.

    Witmer, C M; Harris, R.; Shupack, S I


    Analysis of soil from a specific site in New Jersey indicated a low level of sodium and chromium present as a calcium compound. Chromium was then administered orally to young, mature male rats at a level of 240 micrograms/kg for 14 days as chromium-contaminated soil, as CaCrO4, and as an equimolar mixture of the soil and calcium salts for 14 days. The rats were sacrificed 24 hr after the last dosing, and tissues were taken immediately for chromium analysis. Blood, muscle, and liver contained ...


    Igata, N.; Sato, S; ANDO, T.; H. Doi; Nishikawa, O.; Shibata, M.


    The objective of this investigation is to clarify the behavior of chromium atoms in iron-5at.% chromium alloy. When the specimens were quenched after soultion annealing at 1150°C for 1hr, FIM image was only a bright area, but when they were tempered from 450°C to 650°C, both bright areas and dark areas were observed in the FIM image. In these quenched specimens there was microsegregation of chromium atoms : In bright areas the chromium concentration was lower, and in dark areas it was higher ...

  14. Influence of Chelating Agents on Chromium Fate in Sediment



    A laboratory investigation on reaction between chelating agents and chromium was conducted to evaluate the effect of chelating agents on the adsorption and desorption of chromium in sediment.The amount of adsorbed chromium(VI) in sediment decreased slightly by 5%-10% because of addition of chelating agents.Chelating agents inhibited the removal of Cr(Ⅲ)by sediment from solutions and the inhibiting effect was in the order:citric acid>tartaric acid>EDTA,Salicylic acid.No effect of chelating agents on desorption of chromium in sediment was observed.

  15. Analysing the chromium-chromium multiple bond using multiconfigurational quantum chemistry

    Brynda, Marcin; Gagliardi, Laura; Roos, Björn O.


    This Letter discusses the nature of the chemical bond between two chromium atoms in different di-chromium complexes with the metal atoms in different oxidation states. Starting with the Cr diatom, with its formally sextuple bond and oxidation number zero, we proceed to analyse the bonding in some Cr(I)–Cr(I) XCrCrX complexes with X varying from F, to Phenyl, and Aryl. The bond distance in these complexes varies over a large range: 1.65–1.83 Å and we suggest explanations for these variations. ...

  16. Assessing and influencing the fractional contribution of erythrocyte-bound 59Fe to individual 59Fe tissue content in murine 59Fe distribution studies

    Background: Murine proteins of iron homoeostasis are frequently manipulated to investigate the mechanisms of iron-distribution and their toxicological consequences. Beyond subtracting erythrocyte-bound 59Fe of the residual blood content determined for each tissue (subtraction method), procedures are needed to determine 59Fe distribution in murine models of, e.g. inflammation or diabetes that cause local hyperaemia and changes in microcirculation. Aim: Two new methods were developed to correct total 59Fe tissue content individually for erythrocyte-bound 59Fe-labelled haem iron. Methods: Iron-deficiency and iron-overload was induced in male C57BL6 mice by feeding of respective diets. Distribution of 59Fe between different tissues was determined 24 h, 14, and 28 days after intravenous injection of 59Fe trace amounts. Haem-bound 59Fe was separated from non-haem 59Fe in homogenates from all tissues by dispersion in a mix of lipophilic cyclohexanone and hydrophilic H3PO4 (separation method). Moreover, the reduction of 59Fe-labelled tissue blood content was determined in all organs after in vivo saline perfusion via the left ventricle (perfusion method). Results and discussion: 59Fe-labelled non-haem iron determined by the separation method was not significantly different from values determined by the subtraction method, except for the iron-deficient spleen 14 and 28 days after 59Fe injection when the separation method yielded ∼20% higher values. Approximately 20% of 59Fe-labelled haem iron spilled over into the hydrophilic phase. The impact of this error decreases in parallel to 59Fe radioactivity in the residual tissue blood content: thus, it is higher in iron-deficient mice which accumulate more 59Fe in their erythrocytes than iron-adequate and iron-rich mice. For the same reason this type of error is more marked after long distribution periods and in organs with high residual blood content. Saline perfusion via the left ventricle reduced total blood content in mice

  17. The effect of chromium picolinate on serum cholesterol and apolipoprotein fractions in human subjects.

    Press, R. I.; Geller, J.; Evans, G. W.


    Chromium has been implicated as a cofactor in the maintenance of normal lipid and carbohydrate metabolism. A deficiency of chromium results from diets low in biologically available chromium. Picolinic acid, a metabolite of tryptophan, forms stable complexes with transitional metal ions, which results in an improved bioavailability of the metal ion chromium. To determine whether or not chromium picolinate is effective in humans, 28 volunteer subjects were given either chromium tripicolinate (3...

  18. The Effect of Chromium Added into Basal Diet on Serum Total Protein, Urea, Triglyceride, Cholesterol and Serum and Tissue Chromium, Zinc, Copper Levels in Rabbits

    *, Kâzim ŞAHİN; *, Talat GÜLER; +, N. ŞAHİN; *, O. N. ERTAS; +, N. ERKAL


    This study was conducted to determine the effect of supplemantal dietary chromium on serum total protein, urea, triglycerides, cholesterol, and serum and tissue chromium, zinc, and copper contents of pregnant rabbits, their offspring and their young rabbits. Treatment groups consisted of chromium level as follows: Control Group no supplementation chromium into basal diet, Treatment I (200 ppb Group) contained 200 ppb of supplemental chromium into basal diet, and Treatment II (400 ppb Group...


    Increased intake of chromium has been shown to lead to improvements in glucose, insulin, lipids, and related variables in studies involving humans, experimental and farm animals. However, the results are often variable depending not only upon the selection of subjects, but also dietary conditions a...

  20. Chromium and Polyphenols From Cinnamon Improve Insulin Sensitivity

    Naturally occurring compounds that have been shown to improve insulin sensitivity include chromium and polyphenols found in cinnamon. These compounds also have similar effects on insulin signaling and glucose control. The signs of chromium deficiency are similar to those for the metabolic syndrome ...

  1. IRIS Toxicological Review of Hexavalent Chromium (2010 External Review Draft)

    [UPDATE] New Schedule for IRIS Hexavalent Chromium Assessment In Feb 2012, EPA developed a new schedule for completing the IRIS hexavalent chromium assessment. Based on the recommendations of the external peer review panel, which met in May 2011 to review the dra...

  2. Composition and structure of plasma sprayed chromium steel powders

    Schneeweiss, O.; Voleník, Karel; Kolman, Blahoslav Jan

    Praha, 2005, s. 105-111. ISBN 1899072 18 7. [EURO Powder Metallurgy Congress & Exhibition. Prague (CZ), 02.10.2005-05.10.2005] Institutional research plan: CEZ:AV0Z20430508 Keywords : chromium steel * plasma spraying * chromium depletion * Mössbauer spectroscopy Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass

  3. Safety, absorption, and antioxidant effects of chromium histidine

    Supplemental chromium has been shown to be involved in the alleviation of the metabolic syndrome, glucose intolerance, polycystic ovary syndrome, depression, excess body fat, and gestational, steroid-induced, and type 2 diabetes. Chromium amino acid complexes that contained histidine displayed cons...

  4. Toxicity and adaptation of Dictyosphaerium chlorelloides to extreme chromium contamination.

    Sánchez-Fortún, Sebastián; López-Rodas, Victoria; Navarro, Macarena; Marvá, Fernando; D'ors, Ana; Rouco, Mónica; Haigh-Florez, David; Costas, Eduardo


    Metals are often spilled by industries into inland water environments, with adverse consequences. Numerous papers have reported that heavy metals produce massive destruction of algae. Nevertheless, algal populations seem to become tolerant when they have had previous exposures to heavy metals. Because the mechanisms allowing heavy metal tolerance of algae are not yet known, the present study analyzed the effect of hexavalent chromium on growth and photosynthetic performance of Dictyosphaerium chlorelloides, stressing on the adaptation mechanisms to chromium contamination. Growth and photosynthetic performance of algal cells were inhibited by Cr(VI) at 10 mg/L, and the 72-h median inhibition concentration was established as 1.64 and 1.54 mg/L, respectively. However, after further incubation for a three month period in an environment with 25 mg/L of chromium, some rare, chromium-resistant cells occasionally were found. A Luria-Delbrück fluctuation analysis was performed to distinguish between resistant algae arising from rare, spontaneous mutations and resistant algae arising from physiological adaptation and other adaptive mechanisms. Resistant cells arose only by spontaneous mutations before the addition of chromium, with a rate of 1.77 x 10(-6) mutants per cell division. From a practical point of view, the use of both chromium-sensitive and chromium-resistant genotypes could make possible a specific algal biosensor for chromium. PMID:19323601

  5. Residual Chromium in Leather by Instrumental Neutron Activation Analysis

    S. Okoh


    Full Text Available Problem statement: Most tanning processes employ the use of chromium sulphate. For chromium tanned leather, finished products may contain high amount of residual chromium. This may pose some health hazards, since chromium is known to be toxic at elevated concentration. This justifies the need for the study. Approach: Various samples of leather were collected from a tannery, a leather crafts market, a leather dump site and from local tanners all in Kano, Nigeria in 2009. The samples were irradiated for 6 h in the inner site of the Nigerian Research Reactor (NIRR-1 at a flux of 5×1011 ncm-2 sec-1. Results: After evaluating the spectrum, the mean results for chromium in the samples were determined as 2.33±0.3, 2.23±0.3 and 2.93±0.4% for samples from the tannery, leather crafts market and leather dump sites respectively. Chromium concentration in samples collected from local tanners who use tannins from Acacia nilotica as tanning agent was below the detection limit of Instrumental Neutron Activation Analysis (INAA technique used in the study. Conclusion: Although, the concentrations of chromium in the analysed samples were not much higher than what were obtained in literature, they may be enough to sensitize the population that is allergic to chromium.


    Hard chromium coatings (0.25 to10 mil thick) are used extensively for imparting wear and erosion resistance to components in both industrial and military applications. The most common means of depositing hard chromium has been through the use of chromic acid baths containing ...




    At the Hanford Site, chromium was used as a corrosion inhibitor in the reactor cooling water and was introduced into the groundwater as a result of planned and unplanned discharges from reactors during plutonium production since 1944. Beginning in 1995, groundwater treatment methods were evaluated leading to the use of pump and treat facilities with ion exchange using Dowex 21 K, a regenerable strong base anion exchange resin. This required regeneration of the resin, which is currently performed offsite. Resin was installed in a 4 vessel train, with resin removal required from the lead vessel approximately once a month. In 2007, there were 8 trains (32 vessels) in operation. In 2008, DOE recognized that regulatory agreements would require significant expansion in the groundwater chromium treatment capacity. Previous experience from one of the DOE project managers led to identification of a possible alternative resin, and the contractor was requested to evaluate alternative resins for both cost and programmatic risk reductions. Testing was performed onsite in 2009 and 2010, using a variety of potential resins in two separate facilities with groundwater from specific remediation sites to demonstrate resin performance in the specific groundwater chemistry at each site. The testing demonstrated that a weak base anion single-use resin, ResinTech SIR-700, was effective at removing chromium, had a significantly higher capacity, could be disposed of efficiently on site, and would eliminate the complexities and programmatic risks from sampling, packaging, transportation and return of resin for regeneration. This resin was installed in Hanford's newest groundwater treatment facility, called 100-DX, which began operations in November, 2010, and used in a sister facility, 100-HX, which started up in September of 2011. This increased chromium treatment capacity to 25 trains (100 vessels). The resin is also being tested in existing facilities that utilize Dowex 21 K for

  8. Chromium-Makes stainless steel stainless

    Kropschot, S.J.; Doebrich, Jeff


    Chromium, a steely-gray, lustrous, hard metal that takes a high polish and has a high melting point, is a silvery white, hard, and bright metal plating on steel and other material. Commonly known as chrome, it is one of the most important and indispensable industrial metals because of its hardness and resistance to corrosion. But it is used for more than the production of stainless steel and nonferrous alloys; it is also used to create pigments and chemicals used to process leather.

  9. The electronic structure of antiferromagnetic chromium

    Skriver, Hans Lomholt


    The author has used the local spin density formalism to perform self-consistent calculations of the electronic structure of chromium in the non-magnetic and commensurate antiferromagnetic phases, as a function of the lattice parameter. A change of a few per cent in the atomic radius brings...... the calculated ground state properties into agreement with experiment. The magnetisation is studied as function of volume in several models, and it is shown that a Stoner picture provides an extremely accurate description of the full calculation provided the sp-d hybridisation is taken into account. It is found...

  10. Developing AMS measurement of $^{59}$Ni at CIAE

    Ming, He; Wei, Wang; Xiangdong, Ruan; Chaoli, Li; Kejun, Dong; liang, Du; Bo, Xie Lin; Zhenyu, Li; Guowen, Zhen; Hao, Hu; J., Liu


    Accelerator mass spectrometry (AMS) measurement of $^{59}$Ni has been established at CIAE with the HI-13 tandem accelerator and the recently developed $\\Delta E$-Q3D detection system. $^{59}$Ni standard and commercial NiO samples were measured to check the performance of the $\\Delta E$-Q3D detection system on $^{59}$Ni isobar separation and suppression. An overall suppression factor of about 10$^{7}$ for the interfering isobar $^{59}$Co resulting in detection sensitivity as low as 3.8$\\times ...

  11. 32 CFR 516.59 - Duties and procedures.


    ... PUBLIC RELATIONS LITIGATION Remedies in Procurement Fraud and Corruption § 516.59 Duties and procedures... agencies; contracting officers; inspectors general of the executive branch; correspondence from the...

  12. Effects of UV light and chromium ions on wood flavonoids

    The individual and simultaneous effect of UV light and chromium ions was investigated by spectrophotometric methods on inert surfaces impregnated with quercetin or robinetin. The UV-VIS spectra of the silica gel plates impregnated with these flavonoids were modified characteristically after irradiating ultraviolet light. Even a half an hour of irradiation has caused irreversible changes in the molecule structure. A certain chemical - presumably complexation - was concluded from the change of spectral bands assigned to flavonoids when impregnated with chromic ions. Hexavalent chromium caused more complex changes in the absorption spectra. The differences in the spectra could indicate either the oxidation and decomposition of flavonoids, or some kind of coordination process and the reduction of hexavalent chromium. The simultaneous application of UV light and chromium ions caused more pronounced effects. The complexation process between chromium(III) and flavonoid was completed


    Krzysztof GONDEK


    Full Text Available Storage of waste substances is not indifferent to ecological equilibrium in the environment therefore should not be the ultimate way to limit waste arduousness. Therefore, the conducted investigations aimed to determine the effect of tannery composts and vermicomposts loaded with chromium on this element bioaccumulation in earthworm bodies and biomass of selected plants. Chromium in composts and vermicomposts based on tannery sludges occurred in small quantities and easily soluble compounds. Chromium concentrations in redworm biomass points to this metal accumulation in Eisenia fetida body tissues. This element content in redworm biomass was signifi cantly positively correlated with its content in composts. Chromium content in plants was diversifi ed and on treatments was generally smaller than on mineral treatment or farmyard manure. Chromium absorbed by plants was stored mainly in the root systems, and over the norm content of this element found in vermicomposts did not cause its excessive accumulation in plant biomass.

  14. Biosorption potency of Aspergillus niger for removal of chromium (VI).

    Srivastava, Shaili; Thakur, Indu Shekhar


    Aspergillus niger isolated from soil and effluent of leather tanning mills had higher activity to remove chromium. The potency of Aspergillus niger was evaluated in shake flask culture by absorption of chromium at pH 6 and temperature 30 degrees C. The results of the study indicated removal of more than 75% chromium by Aspergillus niger determined by diphenylcarbazide colorimetric assay and atomic absorption spectrophotometry after 7 days. Study of microbial Cr(VI) reduction and identification of reduction intermediates has been hindered by the lack of analytical techniques that can identify the oxidation state with subcellular spatial resolution. Therefore, removal of chromium was further substantiated by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX), which indicated an accumulation of chromium in the fungal mycelium. PMID:16874547

  15. Specific features of the electrocrystallization of chromium together with molybdenum

    A study was made on molybdenum effect on surface structure and some physicomechanical properties of electrolytic chromium during Cr-Mo electrodeposition from CrO3 solutions with additions of SO42- and SiFe62- anions. Cr-Mo deposition was conducted at 55 deg C and 0.5 A/cm2 current density which corresponds to conditions of hard chromizing. It is shown that the change hardness, hydridation and internal stresses of chromium coatings during their alloying with molybdenum is conditioned by structure change. Mo introduction into chromium is not manifested clearly in these characteristics. The change of chromium structure during deposition with molybdenum is probably related both with change of anion relation in cathode film (decrease of catalytic anion content in it) and peculiarities of chromium electrocrystallization. This requires special study with application of methods for investigation into fine and surface structure

  16. Effect of chromium on growth attributes in sunflower (Helianthus annuus L.)

    FOZIA Andaleeb; MUHAMMAD Anjum Zia; MUHAMMAD Ashraf; ZAFAR Mahmood Khalid


    Heavy metal soil pollution takes place when the metal concentration of soil exceeds natural background level and causes ecological destruction and deterioration of the environment. In the present study, a pot experiment was conducted to evaluate the effect of chromium-contaminated soil in sunflower (Helianthus annuus L.) growth attributes. Three different levels of chromium (Cr) i.e., 20, 40, and 60 mg/kg were applied to three varieties of sunflower (G-3, G-9, and G-59). The results of morphological, chemical, and yield parameters were recorded at crop maturity. The result showed that germination, root, and shoot lengths were decreased with increase in Cr concentrations. A gradual decrease was observed for various morphological parameters like root fresh and dry weights, shoot fresh and dry weights, and plant height with increase in Cr levels. A comparison among Cr treatments obtained a significant decrease in yield parameters as achenes/capitulum, acheues/plant, and 100 achenes weight in three varieties. Cr was significantly absorbed by roots but its transport to other parts of plants was slow, and uptake in seeds was much lower than in roots and shoots.

  17. Selenium protection from cadmium and chromium poisoning

    The interaction of selenium with cadmium and chromium was studied in 168 chicken-broilers (DWCxWR) divided into four equal groups. Eight-week old control animals received an intravenous dose of /sup 115m/Cd Chloride 370 KBq/Kg (Group I), or 51Cr Chloride 370 KBq/Kg (Group II). The kinetics of these isotopes were studied by scintillation spectrometry (NaI/TI) carried out for whole blood, plasma, plasma proteins, urine, feces and homogenates of all organs at various time intervals. Animals in Groups III and IV received eight subcutaneous doses of sodium selenate (5ug) at 8-week intervals prior to /sup 115m/Cd or 51Cr. The kinetics of these elements were studied as in the previous two groups. It was found that selenium affected those kinetics in two ways: (a) by increasing the excretion of Cd by 11 +/- 3% (P < 0.001) and that of Cr by 7 +/- 1% (P < 0.001); and (b) by favoring redistribution of those elements, with significant (P < 0.001) reductions in liver, endocrine glands and kidney and increases (P < 0.01) in bone. The study suggests that selenium protects the animals' vital organs from environmental pollutants, such as cadmium and chromium

  18. The hydrogen anode in chromium electrowinning

    The use of a hydrogen anode for electrowinning of chromium from an ammonium chromium sulfate electrolyte (chrome alum process) was investigated in a laboratory-scale cell equipped with a diaphragm. The composition of the solution and the temperature followed industrial practice. Current density, pH, and anolyte flow rate through the diaphragm were varied and optimized for the cell. For a cathodic current density of 915 A/m2 at 50oC, the optimum initial pH was 2.37. The hydrogen anode was made of a platinized Toray carbon paper (0.35 mg Pt per cm2) supplied by E-TEK. The hydrogen pressure was maintained at 2 cm H20 above ambient atmosphere. The potential of the hydrogen anode was about 1 V lower than that of a Pb-Ag anode (1%Ag) in a similar cell. As expected, no Cr+6 was generated in the anolyte. The cathodic current efficiency was slightly lower with the hydrogen anode than with the Pb-Ag anode. (author)

  19. Biliary excretion of chromium in the rat

    The relative amount of chromium excreted in rat bile after injection of Cr-III is much less than after injection of Cr-VI, about 0.1% and from 6-8% during 5 hours respectively, for corresponding dose levels. The liver to bile ratio was 50-100 for Cr-III injection for Cr-VI the ratio was 2-3. With doses up to 18 μmol Cr/kg, only Cr-III was found in bile even after injection of CR-VI.Glutathione depletion of the liver with cyclohexene oxide decreased chromium excretion in bile. Such treatment also decresed the reduction of Cr-VI to Cr-III in the liver cell as only Cr-VI was found in bile. A different distribution of Cr-III in the liver dependent on whether derived from Cr-VI or taken up by the liver as such must be assumed. Taking into account the usual low penetration of biological membranes by Cr-III, a possible active transport mechanism or a specific diffusable Cr-III compound must be postulated. (author)

  20. 46 CFR 188.10-59 - Recognized classification society.


    ... 46 Shipping 7 2010-10-01 2010-10-01 false Recognized classification society. 188.10-59 Section 188.10-59 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH... classification society. This term means the American Bureau of Shipping or other classification...

  1. 47 CFR 76.59 - Modification of television markets.


    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Modification of television markets. 76.59... MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE Carriage of Television Broadcast Signals § 76.59 Modification of television markets. (a) The Commission, following a written request from a broadcast station or...

  2. 36 CFR 902.59 - Geological and geophysical information.


    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Geological and geophysical information. 902.59 Section 902.59 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT... Geological and geophysical information. Any geological or geophysical information and data (including...

  3. 27 CFR 21.59 - Formula No. 32.


    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Formula No. 32. 21.59... OF THE TREASURY LIQUORS FORMULAS FOR DENATURED ALCOHOL AND RUM Specially Denatured Spirits Formulas and Authorized Uses § 21.59 Formula No. 32. (a) Formula. To every 100 gallons of alcohol add:...

  4. 36 CFR 251.59 - Transfer of authorized improvements.


    ..., voluntary sale, transfer, or through enforcement of a valid legal proceeding or operation of law, ceases to... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Transfer of authorized improvements. 251.59 Section 251.59 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT...

  5. Workshop on effects of chromium coating on Nb3Sn superconductor strand: Proceedings

    This report discusses the following topics: Chromium coating on superconductor strand -- an overview; technology of chromium plating; comparison of wires plated by different platers; search for chromium in copper; strand manufactures' presentations; chromium plating at the Lawrence Livermore National Laboratory; a first look at a chromium plating process development project tailored for T.P.X. and I.T.E.R. strand; and influence of chromium diffusion and related phenomena on the reference ratios of bare and chromium plated Nb3Sn strand

  6. Stabilization of chromium salt in ordinary portland cement

    Damir Barbir; Pero Dabić; Petar Krolo


    Ordinary Portland cement (OPC) samples containing the chromium salt have been investigated using differential microcalorimetry, conductometry and Fourier transform infrared spectroscopic analysis. The effect of chromium on OPC hydration was evaluated by continuous observing of early hydration. The microcalorimetrical results show that with increasing the share of chromium salt, heat maximums assume lower values and the occurrence of the maximum registered in the earlier hydration times. Conductometrical measurements show that with increasing addition of chromium salt, curve did not show any specific shape, immediate drop in specific conductivity is noticed and the maximum is reached earlier. This coincides with microcalorimetrical results. It can be concluded that the addition of chromium does not affect the mechanism of the hydration process, but it does affect the kinetic parameters and dynamics of the cement hydration process. It was found that chromium salt addition to the cement–water system is acceptable up to 2 wt.%. According to standard EN 196-3 for OPC, the beginning of binding time should occur after 60 minutes. Increased amount of chromium over 2 wt.% significantly accelerate the beginning of binding time and for the system it is not acceptable.

  7. Chromium speciation in rainwater: temporal variability and atmospheric deposition

    Kieber, R.J.; Willey, J.D.; Zvalaren, S.D. [University of North Carolina at Wilmington, Wilmington, NC (United States). Dept. of Chemistry


    Chromium is released into the atmosphere by a variety of anthropogenic activities which include steel manufacturing, leather tanning, wood presentation and fossil fuel combustion. The concentrations of the various chromium species were determined in 89 rainwater samples collected in Wilmington, NC from October 1, 1999 to December 31, 2001. Volume weighted annual average concentrations of Cr{sub total}, particulate Cr, Cr(III)(aq), and Cr(VI)(aq) were 4.6, 2.2, 0.8 and 1.2 nM, respectively. There was distinct seasonal and diurnal variability in the concentrations of the various chromium species. Chromium emissions to the global atmosphere by both natural and anthropogenic sources are estimated to be 2.2 x 10{sup 9} mol/yr. Using rainwater concentration data along with other published rainwater Cr concentrations and an estimate for total global annual rain, the total global flux of chromium removed from the atmosphere via wet deposition is 2.1 x 10{sup 9} mol/yr. This represents complete removal of Cr and indicates that essentially all chromium released into the global atmosphere is removed via rain. About half this chromium is dissolved with roughly equal concentrations of toxic Cr(VI) and relatively harmless Cr(III) species. 48 refs., 4 figs., 3 tabs.

  8. Bioavailability of a potato chromium complex to the laboratory rat

    Research objectives were to study the effect of food source, preparation method and chemical form on bioavailability of chromium. Chromium concentration in potatoes was determined and tubers labeled either intrinsically or extrinsically with radioactive chromate. A labeled chromium complexes was isolated from preparations of raw, baked or fried potatoes and chromatographed on gel permeation media. Availability of the potato chromium complex to the rat was examined in three feeding studies. Animals were dosed with radioactive extrinsically or intrinsically labeled potato extract or with chromate. A labeled chromium complex was isolated from gastrointestinal contents of rats and chromatographed. Potato pulp and peel contained 1.63 and 2.70 μg Cr/g tissue respectively. True and apparent absorption from extrinsically labeled feedings were 33.4 +/- 4.7 and 29.8 +/- 11.2% respectively, and no differences existed between absorption from raw and cooked potatoes. Absorption from the extrinsic labeled potatoes differed significantly from absorption of inorganic chromatium. Apparent absorption of raw (11.1 +/- 7.9%) and cooked (-0.7 +/- 2.8%) intrinsically labeled feedings differed significantly. Absorption of inorganic chromium was 17.8% (true) and 11.5% (apparent). Examination of the chromium complex isolated from gastrointestinal tract contents showed enlargement of the complex in the stomach after consumption

  9. Chromium-induced membrane damage: protective role of ascorbic acid


    Importance of chromium as environmental toxicant is largely due to impact on the body to produce cellular toxicity. The impact of chromium and their supplementation with ascorbic acid was studied on plasma membrane of liver and kidney in male Wistar rats (80 - 100gbody weight). It has been observed that the intoxication with chromium ( i. p. ) at the dose of 0.8 mg/100g body weight per day for a period of 28 days causes significant increase in the level of cholesterol and decrease in the level of phospbolipid of both liver and kidney. The alkaline pbosphatase, total ATPase and Na + -K + -ATPase activities were significantly decreased in both liver and kidney after chromium treatment,except total ATPase activity of kidney. It is suggested that chromium exposure at the present dose and duration induce for the alterations of structure and function of both liver and kidney plasma membrane. Ascorbic acid ( i.p. at the dose of 0.5 mg,/100g body weight per day for period of 28 days) supplementation can reduce these structural changes in the plasma membrane of liver and kidney. But the functional changes can not be completely replenished by the ascorbic acid supplementation in response to chromium exposure. So it is also suggested that ascorbic acid (nutritional antioxidant) is useful free radical scavenger to restrain the chromium-induced membrane damage.

  10. Fertilizers and Mixed Crop Cultivation of Chromium Tolerant and Sensitive Plants under Chromium Toxicity

    B. Dheeba; Sampathkumar, P; Kannan, K.


    Zea mays (maize) and Vigna radiata (green gram) are found to be the chromium (Cr) tolerant and sensitive plants, respectively. In the present paper, we investigate the reduction of the toxicity of Cr in the sensitive plants by the mixed crop cultivation in the field using various amendments. Further, the potassium dichromate was used as the source of hexavalent Cr. The results indicated that Cr adversely affects both the growth and yield of plants. The soil properties vary with Cr and differe...

  11. Microbial Diversity of Chromium-Contaminated Soils and Characterization of Six Chromium-Removing Bacteria

    He, Zhiguo; Hu, Yuting; Yin, Zhen; Hu, Yuehua; Zhong, Hui


    Three soil samples obtained from different sites adjacent to a chromium slag heap in a steel alloy factory were taken to examine the effect of chromium contamination on soil bacterial diversity as determined by construction of 16S rDNA clone libraries and sequencing of selected clones based on restriction fragment length polymorphism (RFLP) analysis. Results revealed that Betaproteobacteria, Gammaproteobacteria, Firmicutes, and Alphaproteobacteria occurred in all three soil samples, although the three samples differed in their total diversity. Sample 1 had the highest microbial diversity covering 12 different classes, while Sample 3 had the lowest microbial diversity. Strains of six different species were successfully isolated, one of which was identified as Zobellella denitrificans. To our knowledge, this is the first report of a strain belonging to the genus Zobellella able to resist and reduce chromium. Among all isolates studied, Bacillus odysseyi YH2 exhibited the highest Cr(VI)-reducing capability, with a total removal of 23.5 % of an initial Cr(VI) concentration of 350 mg L-1.

  12. Chromium removal from tannery wastewater by using of flying ash

    A simple and economic method to chromium removal from tannery wastewater by means of flying ash is presented. The chromium removal operation is a discontinuous process that involve the mass of flying ash, time of contact and temperature or ph as variables, their which are optimized through Box-Wilson type experimental design. The results were successful: From an initial fluid whit chromium concentration of 1850m ppm, final concentrations of 0.008 ppm and 0.5 ppm of Cr+3 and Cr+6 respectively were achieved. These post-treatment concentrations are into the approved range definite by Government's Laws to this waste type


    Inga Zinicovscaia


    Full Text Available Due to its widespread industrial use, chromium has become a serious pollutant in diverse environmental settings. The main source of chromium pollution including the Republic o Moldova is industry. It is a great need to develop new eco-friendly methods of chromium removal. Biosorption of heavy metals is a most promising technology involved in the removal of toxic metals from industrial waste streams and natural waters. This article is an extended abstract of a communication presented at the Conference Ecological Chemistry 2012

  14. Thermal incorporation behavior during the reduction and stabilization of chromium wastes

    Yang, Jun; 楊駿


    The possibility of employing periclase to stabilize chromium in chromium wastes into spinel-based ceramics through thermal method was investigated by heating mixture of simulated chromium waste and magnesium oxide. Different types of magnesium oxide precursors were introduced to incorporate chromium oxide into magnesiochromite (MgCr2O4) ranging from 550 ºC to 1350 ºC. Magnesium oxide precursors of both types can effectively incorporate chromium oxide but via different mechanisms. Three main f...

  15. Effects of Supplemental Dietary Chromium on Yield and Nutrient Digestibility of Laying Hens Under Low Temperature

    ŞAHİN, Kazım; ERTAŞ, O. Nihat; GÜLER, Talat; ÇİFTÇİ, Mehmet


    This study was conducted to determine the effects of chromium picolinate (CrPi) added into diet containing 710.3 ppb chromium on yield and nutrient digestibility of laying hens at low temperature. Forty-six-week-old laying hens were randomly assigned to four groups of 30 hens per group. Treatment groups were fed different supplemental dietary chromium levels. Thus, hens were fed diets with no supplemental chromium (Control Group), 100 ppb of supplemental chromium (100 Group), 200 ppb of s...

  16. Evaluation of the comprehensiveness and reliability of the chromium composition of foods in the literature ☆

    Thor, Mayly Y.; Harnack, Lisa; King, Denise; Jasthi, Bhaskarani; Pettit, Janet


    In the early 1960s, trivalent chromium Cr3+ became recognized as an essential trace element due to its potential metabolic and cardiovascular benefits. No comprehensive chromium database currently exists; thus a thorough review of the literature was conducted to examine the availability and reliability of chromium data for foods. A number of key issues were identified that challenge the feasibility of adding chromium to a food and nutrient database. Foremost, dietary chromium data reported in...

  17. Chromium(III) complexation to natural organic matter : Mechanisms and modeling

    Gustafsson, Jon Petter; Persson, I.; Oromieh, A. G.; Van Schaik, J. W. J.; Sjöstedt, Carin; Kleja, D. B.


    Chromium is a common soil contaminant, and it often exists as chromium(III). However, limited information exists on the coordination chemistry and stability of chromium(III) complexes with natural organic matter (NOM). Here, the complexation of chromium(III) to mor layer material and to Suwannee River Fulvic Acid (SRFA) was investigated using EXAFS spectroscopy and batch experiments. The EXAFS results showed a predominance of monomeric chromium(III)-NOM complexes at low pH (<5), in which o...

  18. Abatement of Chromium Emissions from Steelmaking Slags - Cr Stabilization by Phase Separation

    Albertsson, Galina


    Chromium is an important alloying element in stainless steel but also environmentally harmful element. A number of mineralogical phases present in the slag matrix can contain chromium and lead to chromium leaching. Chromium in slag if not stabilized, could oxidize to the cancerogenic hexavalent state, and leach out if exposed to acidic and oxygen rich environment. Other environmental concerns are slag dusting and chromium escape to the atmosphere. Despite the fact that there is a certain risk...

  19. The oxidation and reduction of chromium of stainless steels in an eletric arc furnace

    Arh, B.; F. Tehovnik


    The oxidation of chromium during the elaboration of stainless steels occurs with oxygen in solution blown inthe melt and with oxides in the slag. A higher content of silicon in the furnace charge decreases the extent of oxidation of chromium, however, the efficient reduction of chromium from the slag is of essential importance for a minimal loss of chromium. In this survey, the theory of the oxidation of chromium, its reduction from the slag and the conditions for the formation of foaming sla...

  20. Chromium accumulation, microorganism population and enzyme activities in soils around chromium-containing slag heap of steel alloy factory

    HUANG Shun-hong; PENG Bing; YANG Zhi-hui; CHAI Li-yuan; ZHOU Li-cheng


    The environmental risk of chromium pollution is pronounced in soils adjacent to chromate industry. It is important to investigate the functioning of soil microorganisms in ecosystems exposed to long-term contamination by chromium. 45 soil samples obtained from different places of the slag heap in a steel alloy factory were analyzed for chromium contamination level and its effect on soil microorganisms and enzyme activities. The results show that the average concentrations of total Cr in the soil under the slag heap, adjacent to the slag heap and outside the factory exceed the threshold of Secondary Environmental Quality Standard for Soil in China by 354%, 540% and 184%, respectively, and are 15, 21 and 9 times higher than the local background value, respectively. Elevated chromium loadings result in changes in the activity of the soil microbe, as indicated by the negative correlations between soil microbial population and chromium contents. Dehydrogenase activity is greatly depressed by chromium in the soil. The results imply that dehydrogenase activity can be used as an indicator for the chromium pollution level in the area of the steel alloy factory.

  1. Evaluation of chromium in red blood cells as an indicator of exposure to hexavalent chromium: An in vitro study.

    Devoy, Jérôme; Géhin, Antoine; Müller, Samuel; Melczer, Mathieu; Remy, Aurélie; Antoine, Guillaume; Sponne, Isabelle


    Chromium(VI) compounds are classified as carcinogenic to humans. Whereas chromium measurements in urine and whole blood (i.e., including plasma) are indicative of recent exposure, chromium in red blood cells (RBC) is attributable specifically to Cr(VI) exposure. Before recommending Cr in RBC as a biological indicator of Cr(VI) exposure, in-vitro studies must be undertaken to assess its reliability. The present study examines the relationship between the chromium added to a blood sample and that subsequently found in the RBC. After incubation of total blood with chromium, RBC were isolated, counted and their viability assessed. Direct analysis of chromium in RBC was conducted using Atomic Absorption Spectrometry. Hexavalent, but not trivalent Cr, was seen to accumulate in the RBC and we found a strong correlation between the Cr(VI) concentration added to a blood sample and the amount of Cr in RBC. This relationship appears to be independent of the chemical properties of the human blood samples (e.g., different blood donors or different reducing capacities). Even though in-vivo studies are still needed to integrate our understanding of Cr(VI) toxicokinetics, our findings reinforce the idea that a single determination of the chromium concentration in RBC would enable biomonitoring of critical cases of Cr(VI) exposure. PMID:27178267

  2. The fate of chromium during tropical weathering

    Berger, Alfons; Frei, Robert


    We performed a mineral, geochemical and Cr–Sr–Pb isotope study on a laterite profile developed on ca. 540 Ma old tonalitic bedrock in Madagascar with special emphasis on the behavior of chromium during tropical weathering. The observed strong depletions of Ca, Si, and P, and enrichment of Fe and Al...... weathering profile. The negatively fractionated δ53Cr values measured in the weathering profile relative to the unaltered tonalitic bedrock characterized by a high temperature magmatic inventory Cr isotope signature are consistent with loss of a positively fractionated Cr(VI) pool formed during weathering...... highly oxidative conditions, which in well drained sulfide-bearing parent bedrocks potentially lead to both, acid dissolution of sulfide-hosted Cr and redox-promoted mobilization of Cr(VI) from silicates during later stages of weathering under basic pH conditions....

  3. Neutron capture by the chromium isotopes

    Capture cross sections of the chromium isotopes have been measured at neutron energies up to 350 keV using the capture cross section facility at the 40 m station of the Oak Ridge Electron Linear Accelerator. Parameters have been derived for 180 resonances. A moderate correlation [rho(gamma-n-0,gamma-gamma) approximately 0.45] is observed between reduced neutron widths and radiative widths for s-wave resonances. Calculations of valence widths show that valence capture can only account for the correlated component of the observed radiative widths. An additional mechanism such as a 2p-1h doorway state must therefore be occurring to explain the uncorrelated component. (author)

  4. The chromium isotope composition of reducing and oxic marine sediments

    Gueguen, Bleuenn; Reinhard, Christopher T.; Algeo, Thomas J.; Peterson, Larry C.; Nielsen, Sune G.; Wang, Xiangli; Rowe, Harry; Planavsky, Noah J.


    The chromium (Cr) isotope composition of marine sediments has the potential to provide new insights into the evolution of Earth-surface redox conditions. There are significant but poorly constrained isotope fractionations associated with oxidative subaerial weathering and riverine transport, the major source of seawater Cr, and with partial Cr reduction during burial in marine sediments, the major sink for seawater Cr. A more comprehensive understanding of these processes is needed to establish global Cr isotope mass balance and to gauge the utility of Cr isotopes as a paleoredox proxy. For these purposes, we investigated the Cr isotope composition of reducing sediments from the upwelling zone of the Peru Margin and the deep Cariaco Basin. Chromium is present in marine sediments in both detrital and authigenic phases, and to estimate the isotopic composition of the authigenic fraction, we measured δ53Cr on a weakly acid-leached fraction in addition to the bulk sediment. In an effort to examine potential variability in the Cr isotope composition of the detrital fraction, we also measured δ53Cr on a variety of oxic marine sediments that contain minimal authigenic Cr. The average δ53Cr value of the oxic sediments examined here is -0.05 ± 0.10‰ (2σ, n = 25), which is within the range of δ53Cr values characteristic of the bulk silicate Earth. This implies that uncertainty in estimates of authigenic δ53Cr values based on bulk sediment analyses is mainly linked to estimation of the ratio of Cr in detrital versus authigenic phases, rather than to the Cr-isotopic composition of the detrital pool. Leaches of Cariaco Basin sediments have an average δ53Cr value of +0.38 ± 0.10‰ (2σ, n = 7), which shows no dependency on sample location within the basin and is close to that of Atlantic deepwater Cr (∼+0.5‰). This suggests that authigenic Cr in anoxic sediments may reliably reflect the first-order Cr isotope composition of deepwaters. For Peru Margin samples

  5. Chromium and Polyphenols from Cinnamon and Insulin Sensitivity

    Factors that improve insulin sensitivity usually lead to improvements in risk factors associated with the metabolic syndrome, diabetes, and cardiovascular diseases. Naturally occurring bioactive compounds that have been shown to improve insulin sensitivity include chromium and polyphenols found in ...

  6. Contingency plans for chromium utilization. Publication NMAB-335

    The United States depends entirely on foreign sources for the critical material, chromium, making it very vulnerable to supply disruptions. This vulnerability results because chromium is essential for the fabrication of corrosion-resisting steels and high-temperature, oxidation-resisting alloys in applications that are vital to the nation's technological well-being; because no substitutes are known for these materials in those applications; and because the known, substantial deposits of chromite ore are only in a few geographical locations that could become inaccessible to the United States as a result of political actions. The effectiveness of programs such as stockpiling, conservation, and research and development for substitutes to reduce the impact of disruption of imports of chromite and ferrochromium are discussed. Alternatives for decreasing chromium consumption also are identified for chromium-containing materials in the areas of design, processing, and substitution

  7. Synthesis and characterization of novel chromium pillared clays

    New chromium pillared clays of basal spacing 2.45 nm were synthesized and characterized. The chromium oligomers used for intercalation were prepared by quick addition of base and acid to Cr(III) monomeric solutions followed by reflux. The synthesized clays exhibit increased BET surface area and higher micropore volume compared to clays with lower galleries, pillared either by smaller Cr(III) oligomers or by Cr(III) monomers. Important parameters affecting the d001 basal spacing were studied, e.g. the pH of the pillaring solution, the intercalation time, the chromium concentration and the counter-anion present in the chromium solutions. Scanning electron micrographs were acquired to demonstrate changes of the clay texture before and after pillaring. The thermal behavior of the synthesized clays was also examined

  8. Adsorption Properties of Chromium (VI by Chitosan Coated Montmorillonite

    Dahe Fan


    Full Text Available The adsorption of chromium (VI by Chitosan Coated Montmorillonite (CCM from aqueous solution was studied. To evaluate the adsorption capacity, the effects of pH, initial concentration and temperature on the adsorption were investigated. The isothermal data was applied to Langmuir linear and the Freundlich linear isotherm equation and the thermodynamic parameters (ΔH, ΔG, ΔS were calculated according to the values of binding Langmuir constant, KL. Results indicated that the adsorption between CCM and chromium (VI was significantly physical, the negative ΔH constant at lower temperature confirmed that the more chromium (VI was adsorbed by chitosan coated montmorillonite at lower temperature. The kinetics of the sorption process of chromium (VI on chitosan coated montmorillonite were investigated using the pseudo-first order and pseudo-second order kinetics, results showed that the pseudo-second order equation model provided the best correlation with the experimental results.

  9. IRIS Toxicological Review of Hexavalent Chromium (Peer Review Plan)

    EPA is conducting a peer review of the scientific basis supporting the human health hazard and dose-response assessment of hexavalent chromium that will appear on the Integrated Risk Information System (IRIS) database.

  10. Fabrication of high rate chromium getter sources for fusion applications

    Design and fabrication techniques are described for the manufacture of large-capacity chromium getter sources, analogous to the commercially available titanium getter source known as Ti-Ball, manufactured by Varian Associates