Study of the analytic quality in the determinations of Cr, Fe, Mn, Cu, Zn, Pb and Hg through conventional and nuclear analytical techniques in mosses of the MATV

International Nuclear Information System (INIS)

Caballero S, B.

2013-01-01

To evaluate the environmental risks of air pollution and to facilitate the decision-making for control, is necessary to have the capacity to generate data with analytical quality. A comparison between nuclear (Neutron activation analysis and total reflection X-ray fluorescence spectrometry) and no nuclear analytical techniques (atomic absorption spectrometry and inductively coupled plasma optical emission spectrometry) for simultaneous determination of metal content (Cr, Cu, Fe, Hg, Mn, Pb and Zn) in mosses from Metropolitan Area of the Toluca Valley (MATV) was performed. Epiphytic mosses (Fabriona ciliaris and Leskea angustata) were sampled in two campaigns, 16 sites (urban, transition and natural) and were prepared for each technique. The biological certified reference materials were used for the quality control and to evaluate accuracy, precision, linearity, detection and quantification limits. Results show that nuclear analytical techniques and no nuclear applied in chemical analysis of Cr, Cu, Fe, Hg, Mn, Pb and Zn in moss from MATV are comparable and therefore all of these can potentially be used for this purpose. However, if its considered both, the performance parameters and economic/operational characteristics is widely recommended inductively coupled plasma optical emission spectrometry, conventional analytical technique, which showed the highest analytical grade quality. Also were observed spatial and temporal variations in the concentrations of Cr, Cu, Fe, Hg, Mn, Pb and Zn in mosses from MATV and was discussed its potential origin. The urban sites had the highest concentration of anthropogenic elements as Cr, Cu, Fe, Hg, Pb and Zn because are strongly impacted by roads with high vehicle traffic. (Author)

Evaluation of the heavy metals Cr, Mn, Fe, Cu, Zn and Pb in water penny wort (Hydrocotyle ranunculoides) from the upper course of the Lerma River, Mexico

International Nuclear Information System (INIS)

Zarazua, G.; Avila P, P.; Tejeda, S.; Valdivia B, M.; Macedo M, G.; Zepeda G, C.

2013-01-01

The Lerma river is one of the most polluted water bodies in Mexico, it presents low biodiversity and lets grow up aquatic plants resistant to the pollution. The aim of this work was to evaluate the concentration and bioaccumulation factors of Cr, Mn, Fe, Cu, Zn and Pb in aerial and submerged structures of water penny wort (Hydrocotyle ranunculoides) from the upper course of the Lerma river. Inductively coupled plasma-optical emission spectrometry was used to determine the concentration of heavy metals in water and H. ranunculoides. Results show that the bioaccumulation factors of Fe and Zn were higher than those of Cu, Mn, Cr and Pb; with the exception of Zn, bioaccumulation factors were higher in the submerged structures of the plant, which shows low mobility of analyzed metals. As a result of this study H. ranunculoides can be considered as good indicator of metal pollution in water bodies. (Author)

Mechanism of formation of perovskite phase and dielectric properties of Pb(Zn,Mg)1/3Nb2/3O3 ceramics prepared by columbite precursor routes

International Nuclear Information System (INIS)

Jang, H.M.; Cho, S.R.; Lee, K.M.

1995-01-01

The mechanism of formation of the perovskite phase and the dielectric properties of Pb(Zn,Mg) 1/3 Nb 2/3 O 3 (PZMN) ceramics were examined using two different types of columbite precursors, (Mg,Zn)Nb 2 O 6 (MZN) and MgNb 2 O 6 + ZnNb 2 O 6 (MN + ZN). The formation of perovskite phase in the PbO + MN + ZN system is characterized by an initial rapid formation of Mg-rich perovskite phase, followed by a sluggish formation of Zn-rich perovskite phase. On the other hand, due to the formation of pyrochlore phase of mixed divalent cations Pb 2-x (Zn,Mg) y Nb 2-y O 7-x-3y/2 , the pyrochlore/perovskite transformation in the PbO + MZN system proceeded uniformly with a spatial homogeneity. Further analysis suggested that the formation of perovskite phase is a diffusion-controlled process. The degree of diffuseness of the rhombohedral/cubic phase transition (DPT) is higher in the PbO + MN + ZN system than in the PbO + MZN specimen for T > T max (temperature of the dielectric permittivity maximum), indicating a broadened compositional distribution of the B-site cations in the PbO + MN + ZN system

Determination of Mn, Fe, Ni, Cu, Zn and Pb contents in samples in samples of apple trees by radionuclide X-ray fluorescence analysis

International Nuclear Information System (INIS)

Bumbalova, A.; Havranek, E.; Harangozo, M.

1982-01-01

The applicability of the radionuclide X-ray fluorescence analysis (RXFA) for qualitative and quantitative evaluation of environmental plant samples is discussed and examples of determination of Mn, Fe, Ni, Cu, Zn, Pb in samples of apple trees are given. The instrumentation, the standard and sample preparation are also presented. (author)

Optical properties of Mn doped ZnO films and wires synthesized by thermal oxidation of ZnMn alloy

International Nuclear Information System (INIS)

Sima, M.; Mihut, L.; Vasile, E.; Sima, Ma.; Logofatu, C.

2015-01-01

Mn doped ZnO films and wires, having different manganese concentrations were synthesized by thermal oxidation of the corresponding ZnMn alloy films and wires electrodeposited on a gold substrate. Structural and optical properties were addressed with scanning electron microscopy, X-ray diffraction (XRD), Raman scattering and photoluminescence (PL). To estimate the manganese concentration in Mn doped ZnO films, X-ray photoelectron spectroscopy was used. XRD patterns indicate that the incorporation of Mn 2+ ions into the Zn 2+ site of ZnO lattice takes place. Quenching of the ZnO PL appears due to Mn 2+ ions in the ZnO lattice. Moreover, a significant decrease in the green emission of ZnO is reported in the case of the Mn doped ZnO wire array with a Mn concentration of 1.45%. The wurtzite ZnO has a total of 12 phonon modes, namely, one longitudinal acoustic (LA), two transverse acoustic (TA), three longitudinal optical (LO), and six transverse optical branches. Compared to the undoped ZnO, a gradual up-shift of the Raman lines assigned to the 2LA and A 1 (LO) vibrational modes, from 482 and 567 cm −1 to 532 and 580 cm −1 , respectively, takes place for the Mn doped ZnO films having a Mn concentration between 2 and 15%. Additionally, in the case of the Mn doped ZnO films with 7 and 15% Mn concentration, Raman spectra show the appearance and increase in the relative intensity of the ZnO Raman line assigned to the TA + LO vibrational mode in the 600–750 cm −1 spectral range. For the Mn-doped ZnO wires, the presence of the Raman line peaking at 527 cm −1 confirms the insertion of Mn 2+ ions in ZnO lattice. - Highlights: • Mn doped ZnO films and wires grown by thermal oxidation of ZnMn alloy • Incorporation of Mn 2+ ions into Zn 2+ site of ZnO lattice • Appearance of a strong Raman line in the spectral range 600–800 cm −1 at high Mn concentration • Compensation of the oxygen vacancy at higher Mn concentration in ZnO lattice

Optical properties of Mn doped ZnO films and wires synthesized by thermal oxidation of ZnMn alloy

Energy Technology Data Exchange (ETDEWEB)

Sima, M., E-mail: msima@infim.ro [National Institute of Materials Physics, 105bis Atomistilor Street, 077125 Magurele (Romania); Mihut, L. [National Institute of Materials Physics, 105bis Atomistilor Street, 077125 Magurele (Romania); Vasile, E. [University “Politehnica”of Bucharest, Faculty of Applied Chemistry and Material Science, Department of Oxide Materials and Nanomaterials, No. 1-7 Gh. Polizu Street, 011061 Bucharest (Romania); Sima, Ma.; Logofatu, C. [National Institute of Materials Physics, 105bis Atomistilor Street, 077125 Magurele (Romania)

2015-09-01

Mn doped ZnO films and wires, having different manganese concentrations were synthesized by thermal oxidation of the corresponding ZnMn alloy films and wires electrodeposited on a gold substrate. Structural and optical properties were addressed with scanning electron microscopy, X-ray diffraction (XRD), Raman scattering and photoluminescence (PL). To estimate the manganese concentration in Mn doped ZnO films, X-ray photoelectron spectroscopy was used. XRD patterns indicate that the incorporation of Mn{sup 2+} ions into the Zn{sup 2+} site of ZnO lattice takes place. Quenching of the ZnO PL appears due to Mn{sup 2+} ions in the ZnO lattice. Moreover, a significant decrease in the green emission of ZnO is reported in the case of the Mn doped ZnO wire array with a Mn concentration of 1.45%. The wurtzite ZnO has a total of 12 phonon modes, namely, one longitudinal acoustic (LA), two transverse acoustic (TA), three longitudinal optical (LO), and six transverse optical branches. Compared to the undoped ZnO, a gradual up-shift of the Raman lines assigned to the 2LA and A{sub 1} (LO) vibrational modes, from 482 and 567 cm{sup −1} to 532 and 580 cm{sup −1}, respectively, takes place for the Mn doped ZnO films having a Mn concentration between 2 and 15%. Additionally, in the case of the Mn doped ZnO films with 7 and 15% Mn concentration, Raman spectra show the appearance and increase in the relative intensity of the ZnO Raman line assigned to the TA + LO vibrational mode in the 600–750 cm{sup −1} spectral range. For the Mn-doped ZnO wires, the presence of the Raman line peaking at 527 cm{sup −1} confirms the insertion of Mn{sup 2+} ions in ZnO lattice. - Highlights: • Mn doped ZnO films and wires grown by thermal oxidation of ZnMn alloy • Incorporation of Mn{sup 2+} ions into Zn{sup 2+} site of ZnO lattice • Appearance of a strong Raman line in the spectral range 600–800 cm{sup −1} at high Mn concentration • Compensation of the oxygen vacancy at higher

Radionuclide X-ray fluorescence determination of Mn, Fe, Cu, Zn and Pb in wastewaters and sludges from wastewater treatment plants in Bratislava (SR)

International Nuclear Information System (INIS)

Harangozo, M.; Toelgyessy, J.

1997-01-01

Radiometric X-ray fluorescence analysis was used for the determination of Mn, Fe, Cu, Zn and Pb in wastewater and sludges from three wastewater treatment plants in Bratislava (SR). Metals were determined in wastewaters after preconcentration by 8-hydroxyquinoline and in sludges by drying and pressing to pellets. 238 Pu and 109 Cd was used for excitation of fluorescence radiation. (author)

The accumulation of elements in plants growing spontaneously on small heaps left by the historical Zn-Pb ore mining.

Science.gov (United States)

Stefanowicz, Anna M; Stanek, Małgorzata; Woch, Marcin W; Kapusta, Paweł

2016-04-01

The study evaluated the levels of nine metals, namely Ca, Cd, Fe, K, Mg, Mn, Pb, Tl, and Zn, in soils and tissues of ten plant species growing spontaneously on heaps left by historical mining for Zn-Pb ores. The concentrations of Cd, Pb, Tl, and Zn in heap soils were much higher than in control soils. Plants growing on heaps accumulated excessive amounts of these elements in tissues, on average 1.3-52 mg Cd kg(-1), 9.4-254 mg Pb kg(-1), 0.06-23 mg Tl kg(-1) and 134-1479 mg Zn kg(-1) in comparison to 0.5-1.1 mg Cd kg(-1), 2.1-11 mg Pb kg(-1), 0.02-0.06 mg Tl kg(-1), and 23-124 mg Zn kg(-1) in control plants. The highest concentrations of Cd, Pb, and Zn were found in the roots of Euphorbia cyparissias, Fragaria vesca, and Potentilla arenaria, and Tl in Plantago lanceolata. Many species growing on heaps were enriched in K and Mg, and depleted in Ca, Fe, and Mn. The concentrations of all elements in plant tissues were dependent on species, organ (root vs. shoot), and species-organ interactions. Average concentrations of Ca, K, and Mg were generally higher in shoots than in roots or similar in the two organs, whereas Cd, Fe, Pb, Tl, and Zn were accumulated predominantly in the roots. Our results imply that heaps left by historical mining for Zn-Pb ores may pose a potential threat to the environment and human health.

Efeito da adição de fontes de matéria orgânica como amenizantes do efeito tóxico de B, Zn, Cu, Mn e Pb no cultivo de Brassica juncea Effect of sources of organic matter in the alleviation of the toxic effects of B, Zn, Cu, Mn and Pb to Brassica Juncea

Directory of Open Access Journals (Sweden)

Glaucia Cecília Grabrielli dos Santos

2007-08-01

Full Text Available Atividades humanas como mineração, siderurgia e aplicação de fertilizantes tornam a poluição por metais sério problema ambiental na atualidade. A fitorremediação - uso de plantas e da microbiota, associada ou não a adições de amenizantes de solo, para extrair, seqüestrar e, ou, reduzir a toxicidade dos poluentes - tem sido descrita como uma tecnologia efetiva, não-destrutiva, econômica e socialmente aceita para remediar solos poluídos. O objetivo deste trabalho foi avaliar a eficiência da mostarda na remoção de Zn, Cu, Mn, Pb e B de um solo contaminado e o efeito da adição de materiais orgânicos na redução da disponibilidade de metais pesados e B para essa planta. O trabalho foi realizado em casa de vegetação, com delineamento inteiramente casualizado em esquema fatorial 3 x 5 com quatro repetições, utilizando 0, 7, 14, 21 e 28 g kg-1 de C no solo. Os materiais orgânicos utilizados foram: solomax, turfa e concentrado húmico mineral (CHM. A adição de turfa e concentrado húmico mineral reduziu os teores de Zn, Cu, Pb e B extraíveis do solo e na parte aérea da mostarda; contudo, essa redução não foi suficiente para impedir os efeitos fitotóxicos dos elementos. A adição dos materiais orgânicos promoveu aumento nos teores de Mn no solo, entretanto apenas o solomax proporcionou aumento na concentração do elemento na parte aérea das plantas. Os efeitos da turfa e do CHM sobre a disponibilidade de Zn, Cu, Mn, Pb e B no solo, a concentração na parte aérea e o crescimento das plantas indicaram o potencial desses materiais como agentes amenizantes de toxicidade e do solomax como auxiliar em programas de fitoextração induzida.As a result of anthropogenic activities such as mining, metal industry and agricultural fertilizer application, metal pollution has become one of the most serious environmental problems of today. Phytoremediation denotes the use of plants and micro-biota, together or without soil

Pb(II), Cd(II) and Zn(II) adsorption on low grade manganese ore ...

African Journals Online (AJOL)

Low grade manganese ore (LMO) of Orissa containing 58.37% SiO2, 25.05% MnO2, 8.8% Al2O3, and 5.03% Fe2O3 as the main constituents was taken to study its adsorption behaviour for Pb(II), Cd(II) and Zn(II) from aqueous solutions. The XRD studies showed the crystalline phases to be quartz, ß-MnO2, d-MnO2 and ...

Synthesis of highly luminescent Mn:ZnSe/ZnS nanocrystals in aqueous media

International Nuclear Information System (INIS)

Fang Zheng; Wu Ping; Zhong Xinhua; Yang Yongji

2010-01-01

High-quality water-dispersible Mn 2+ -doped ZnSe core/ZnS shell (Mn:ZnSe/ZnS) nanocrystals have been synthesized directly in aqueous media. Overcoating a high bandgap ZnS shell around the Mn:ZnSe cores can bring forward an efficient energy transfer from the ZnSe host nanocrystals to the dopant Mn. The quantum yields of the dopant Mn photoluminescence in the as-prepared water-soluble Mn:ZnSe/ZnS core/shell nanocrystals can be up to 35 ± 5%. The optical features and structure of the obtained Mn:ZnSe/ZnS core/shell nanocrystals have been characterized by UV-vis, PL spectroscopy, TEM, XRD and ICP elementary analysis. The influences of various experimental variables, including the Mn concentration, the Se/Zn molar ratio as well as the kind and amount of capping ligand used in the core production and shell deposition process, on the luminescent properties of the obtained Mn:ZnSe/ZnS nanocrystals have been systematically investigated.

Heavy metals and health risk assessment of arable soils and food crops around Pb-Zn mining localities in Enyigba, southeastern Nigeria

Science.gov (United States)

Obiora, Smart C.; Chukwu, Anthony; Davies, Theophilus C.

2016-04-01

This study determined the heavy metals concentration in arable soils and associated food crops around the Pb-Zn mines in Enyigba, Nigeria, and metal transfer factors were calculated. Air-dried samples of the soils and food crops were analyzed for 8 known nutritional and toxic heavy metals by Inductively Coupled Plasma - Mass Spectrometer (ICP-MS) method. Eighty seven percent of all the 20 sampled soils contain Pb in excess of the maximum allowable concentration (MAC) set by Canadian Environmental Quality Guideline (CCME) and European Union (EU) Standard, while Zn in thirty-one percent of the samples exceeded the CCME for MAC of 200 mg/kg. All the food crops, with the exception of yam tuber, contain Pb which exceeded the 0.43 mg/kg and 0.3 mg/kg MAC standards of EU and WHO/FAO respectively, with the leafy vegetables accumulating more Pb than the tubers. The metal transfer factors in the tubers and the leafy vegetables were in the order: Mo > Cu > Zn > Mn > As > Cd > Cr > Ni > Pb and Cd > Cu > Zn > Mn > Mo > As > Ni > Pb > Cr, respectively. Risk assessment studies revealed no health risk in surrounding populations for most of the heavy metals. However, Pb had a high health risk index (HRI) of 1.1 and 1.3, in adults and children, respectively for cassava tuber; Pb had HRI > 1 in lemon grass while Mn also had HRI > 1 in all the leafy vegetables for both adult and children. This high level of HRI for Pb and Mn is an indication that consumers of the food crops contaminated by these metals are at risk of health problems such as Alzheimers' disease and Manganism, associated with excessive intake of these metals. Further systematic monitoring of heavy metal fluxes in cultivable soils around the area of these mines is recommended.

Interface charge transfer process in ZnO:Mn/ZnS nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Stefan, M.; Toloman, D., E-mail: dana.toloman@itim-cj.ro; Popa, A. [National Institute for R & D of Isotopic and Molecular Technology (Romania); Mesaros, A. [Technical University of Cluj-Napoca, Superconductivity, Spintronics and Surface Science Center – C4S (Romania); Vasile, O. R. [University “Politehnica” from Bucharest, Faculty of Applied Chemistry and Material Science (Romania); Leostean, C.; Pana, O. [National Institute for R & D of Isotopic and Molecular Technology (Romania)

2016-03-15

ZnO:Mn/ZnS nanocomposites were prepared by seed-mediated growth of ZnS QDs onto the preformed ZnO:Mn nanoparticles. The formation of the nanocomposite structure has been evidenced by XRD, HRTEM, and XPS. The architecture of the nanocomposite with outer ZnS QDs around ZnO:Mn cores is sustained by the sulfur and oxygen depth profiles resulted from XPS. When the two components are brought together, the band gap of ZnS component decreases while that of ZnO:Mn increases. It is the result of interface charge transfer from ZnO:Mn to ZnS QDs. Here ZnO:Mn valence states are extended through the interface into unoccupied gap states of ZnS. The energy band setup is modified from a type II into a type I band alignment. The process is accompanied by enhancement of composite UV emission of PL spectra as compared to its counterparts. The charge transfer from valence band also determines the increase of the core-polarization effect of sshell electrons at Mn{sup 2+} nucleus, thus determining the increase of the hyperfine field through the reduction of the covalency degree of Zn(Mn)–O bonds. The quantum confinement in ZnS QDs promotes the ferromagnetic coupling of singly occupied states due to Zn vacancies determining a superparamagnetic behavior of the ensemble. When the nanocomposites are formed, due to interface charge transfer effects, an increased number of filled cation vacancies in ZnS QDs develop, thus disrupting the pre-existing ferromagnetic coupling between spins resulting in a significant reduction of the overall saturation magnetization. The possibility to modulate nanocomposite properties by controlling the interface interactions may be foreseen in these types of materials.

Solubility limit of Mn{sup 2+} ions in Zn{sub 1−x}Mn{sub x}Te nanocrystals grown within an ultraviolet-transparent glass template

Energy Technology Data Exchange (ETDEWEB)

Silva, Alessandra dos Santos, E-mail: alemestrado@gmail.com [Universidade Federal de Uberlândia, Laboratório de Novos Materiais Isolantes e Semicondutores (LNMIS), Instituto de Física (Brazil); Silva, Sebastião William da; Morais, Paulo Cesar de [Universidade de Brasília, Núcleo de Física Aplicada, Instituto de Física (Brazil); Dantas, Noelio Oliveira [Universidade Federal de Uberlândia, Laboratório de Novos Materiais Isolantes e Semicondutores (LNMIS), Instituto de Física (Brazil)

2016-05-15

This paper reports on the synthesis of Zn{sub 1−x}Mn{sub x}Te nanocrystals (NCs) (with 0 ≤ x ≤ 0.800) within a PZABP glass system (P{sub 2}O{sub 5}–ZnO–Al{sub 2}O{sub 3}–BaO–PbO) using the fusion method. The as-grown samples were investigated by optical absorption measurements, atomic force microscopy, X-ray diffraction, and Raman spectroscopy. The mean radius of the as-produced NCs (around R ≈ 2.2 nm) was well below the exciton Bohr radius of the bulk ZnTe (5.2 nm). All the characterization techniques employed in this report confirmed the successful inclusion of Mn{sup 2+} ions in the ZnTe-based NCs (Zn{sub 1−x}Mn{sub x}Te NCs) up to the nominal solubility limit of x = 0.100. Above this solubility limit (around x = 0.100), one can observe the formation of MnO and α-MnO{sub 2} NCs, since the nucleation rate for the formation of these NCs is greater than that of Zn{sub 1−x}Mn{sub x}Te NCs, at high x concentrations.Graphical abstract.

Li(Zn,Co,MnAs: A bulk form diluted magnetic semiconductor with Co and Mn co-doping at Zn sites

Directory of Open Access Journals (Sweden)

Bijuan Chen

2016-11-01

Full Text Available We report the synthesis and characterization of a series of bulk forms of diluted magnetic semiconductors Li(Zn1-x-yCoxMnyAs with a crystal structure close to that of III-V diluted magnetic semiconductor (Ga,MnAs. No ferromagnetic order occurs with single (Zn,Co or (Zn, Mn substitution in the parent compound LiZnAs. Only with co-doped Co and Mn ferromagnetic ordering can occur at the Curie temperature ∼40 K. The maximum saturation moment of the this system reached to 2.17μB/Mn, which is comparable to that of Li (Zn,MnAs. It is the first time that a diluted magnetic semiconductor with co-doping Co and Mn into Zn sites is achieved in “111” LiZnAs system, which could be utilized to investigate the basic science of ferromagnetism in diluted magnetic semiconductors. In addition, ferromagnetic Li(Zn,Co,MnAs, antiferromagnetic LiMnAs, and superconducting LiFeAs share square lattice at As layers, which may enable the development of novel heterojunction devices in the future.

Luminescence of nanocrystalline ZnSe:Mn2+

NARCIS (Netherlands)

Suyver, J.F.; Wuister, S.F.; Kelly, J.J.; Meijerink, A.

2000-01-01

The luminescence properties of nanocrystalline ZnSe:Mn^(2+) prepared via an inorganic chemical synthesis are described. Photoluminescence spectra show distinct ZnSe and Mn^(2+) related emissions, both of which are excited via the ZnSe host lattice. The Mn^(2+) emission wavelength and the

High Br- Content CsPb(Cl yBr1- y)3 Perovskite Nanocrystals with Strong Mn2+ Emission through Diverse Cation/Anion Exchange Engineering.

Science.gov (United States)

Li, Fei; Xia, Zhiguo; Pan, Caofeng; Gong, Yue; Gu, Lin; Liu, Quanlin; Zhang, Jin Z

2018-04-11

The unification of tunable band edge (BE) emission and strong Mn 2+ doping luminescence in all-inorganic cesium lead halide perovskite nanocrystals (NCs) CsPbX 3 (X = Cl and Br) is of fundamental importance in fine tuning their optical properties. Herein, we demonstrate that benefiting from the differentiation of the cation/anion exchange rate, ZnBr 2 and preformed CsPb 1- x Cl 3 : xMn 2+ NCs can be used to obtain high Br - content Cs(Pb 1- x- z Zn z )(Cl y Br 1- y ) 3 : xMn 2+ perovskite NCs with strong Mn 2+ emission, and the Mn 2+ substitution ratio can reach about 22%. More specifically, the fast anion exchange could be realized by the soluble halide precursors, leading to anion exchange within a few seconds as observed from the strong BE emission evolution, whereas the cation exchange instead generally required at least a few hours; moreover, their exchange mechanism and dynamics process have been evaluated. The Mn 2+ emission intensity could be further varied by controlling the replacement of Mn 2+ by Zn 2+ with prolonged ion exchange reaction time. White light emission of the doped perovskite NCs via this cation/anion synergistic exchange strategy has been realized, which was also successfully demonstrated in a prototype white light-emitting diode (LED) device based on a commercially available 365 nm LED chip.

Extremely High Phosphate Sorption Capacity in Cu-Pb-Zn Mine Tailings.

Science.gov (United States)

Huang, Longbin; Li, Xiaofang; Nguyen, Tuan A H

2015-01-01

Elevated inorganic phosphate (Pi) concentrations in pore water of amended tailings under direct revegetation may cause toxicity in some native woody species but not native forbs or herb species, all of which are key constituents in target native plant communities for phytostabilizing base metal mine tailings. As a result, Pi sorption capacity has been quantified by a conventional batch procedure in three types of base metal mine tailings sampled from two copper (Cu)-lead (Pb)-zinc (Zn) mines, as the basis for Pi-fertiliser addition. It was found that the Pi-sorption capacity in the tailings and local soil was extremely high, far higher than highly weathered agricultural soils in literature, but similar to those of volcanic ash soils. The Langmuir P-sorption maximum was up to 7.72, 4.12, 4.02 and 3.62 mg P g-1 tailings, in the fresh tailings of mixed Cu-Pb-Zn streams (MIMTD7), the weathered tailings of mixed Cu-Pb-Zn streams (MIMTD5), EHM-TD (fresh Cu-stream, high magnetite content) and local soil (weathered shale and schist), respectively. Physicochemical factors highly correlated with the high Pi-sorption in the tailings were fine particle distribution, oxalate and dithionite-citrate-bicarbonate extractable Fe (FeO and Fed), oxalate-extractable Al and Mn, and the levels of soluble Cd and Zn, and total S and Fe. Large amounts of amorphous Fe oxides and oxyhydroxides may have been formed from the oxidation of pyritic materials and redox cycles of Fe-minerals (such as pyrite (FeS2), ankerite (Ca(Fe Mg)(CO3)2 and siderite (FeCO3), as indicated by the extractable FeO values. The likely formation of sparingly soluble Zn-phosphate in the Pb-Zn tailings containing high levels of Zn (from sphalerite ((Zn,Fe)S, ZnS, (Zn,Cd)S)) may substantially lower soluble Zn levels in the tailings through high rates of Pi-fertiliser addition. As a result, the possibility of P-toxicity in native plant species caused by the addition of soluble phosphate fertilizers would be minimal.

Atomic absorption spectrophotometric determination of microgram levels of Co, Ni, Cu, Pb, and Zn in soil and sediment extracts containing large amounts of Mn and Fe

Science.gov (United States)

Chao, T.T.; Sanzolone, R.F.

1973-01-01

An atomic absorption spectrophotometric method has been developed for the determination of seven metal ions in the hydroxylamine extract of soils and sediments. Mn, Fe, and Zn are directly determined in the aqueous extract upon dilution. Co, Ni, Cu, and Pb in a separate aliquot of the extract are chelated with APDC (ammonium pyrrolidine dithiocarbamate) and extracted into MIBK (methyl isobutyl ketone) before determination. Data are presented to show the quantitative recovery of microgram levels of Co, Ni, Cu, and Pb by APDC-MIBK chelation-extraction from synthetic solutions containing as much as 2,000 ug/ml (micrograms per milliliter) Mn or 50 ug/ml Fe. Recovery of known amounts of the metal ions from sample solutions is equally satisfactory. Reproducible results are obtained by replicate analyses of two sediment samples for the seven metals.

Photoluminescence study of ZnS and ZnS:Pb nanoparticles

International Nuclear Information System (INIS)

Virpal,; Hastir, Anita; Kaur, Jasmeet; Singh, Gurpreet; Singh, Ravi Chand

2015-01-01

Photoluminescence (PL) study of pure and 5wt. % lead doped ZnS prepared by co-precipitation method was conducted at room temperature. The prepared nanoparticles were characterized by X-ray Diffraction (XRD), UV-Visible (UV-Vis) spectrophotometer, Photoluminescence (PL) and Raman spectroscopy. XRD patterns confirm cubic structure of ZnS and PbS in doped sample. The band gap energy value increased in case of Pb doped ZnS nanoparticles. The PL spectrum of pure ZnS was de-convoluted into two peaks centered at 399nm and 441nm which were attributed to defect states of ZnS. In doped sample, a shoulder peak at 389nm and a broad peak centered at 505nm were observed. This broad green emission peak originated due to Pb activated ZnS states

Extremely High Phosphate Sorption Capacity in Cu-Pb-Zn Mine Tailings.

Directory of Open Access Journals (Sweden)

Longbin Huang

Full Text Available Elevated inorganic phosphate (Pi concentrations in pore water of amended tailings under direct revegetation may cause toxicity in some native woody species but not native forbs or herb species, all of which are key constituents in target native plant communities for phytostabilizing base metal mine tailings. As a result, Pi sorption capacity has been quantified by a conventional batch procedure in three types of base metal mine tailings sampled from two copper (Cu-lead (Pb-zinc (Zn mines, as the basis for Pi-fertiliser addition. It was found that the Pi-sorption capacity in the tailings and local soil was extremely high, far higher than highly weathered agricultural soils in literature, but similar to those of volcanic ash soils. The Langmuir P-sorption maximum was up to 7.72, 4.12, 4.02 and 3.62 mg P g-1 tailings, in the fresh tailings of mixed Cu-Pb-Zn streams (MIMTD7, the weathered tailings of mixed Cu-Pb-Zn streams (MIMTD5, EHM-TD (fresh Cu-stream, high magnetite content and local soil (weathered shale and schist, respectively. Physicochemical factors highly correlated with the high Pi-sorption in the tailings were fine particle distribution, oxalate and dithionite-citrate-bicarbonate extractable Fe (FeO and Fed, oxalate-extractable Al and Mn, and the levels of soluble Cd and Zn, and total S and Fe. Large amounts of amorphous Fe oxides and oxyhydroxides may have been formed from the oxidation of pyritic materials and redox cycles of Fe-minerals (such as pyrite (FeS2, ankerite (Ca(Fe Mg(CO32 and siderite (FeCO3, as indicated by the extractable FeO values. The likely formation of sparingly soluble Zn-phosphate in the Pb-Zn tailings containing high levels of Zn (from sphalerite ((Zn,FeS, ZnS, (Zn,CdS may substantially lower soluble Zn levels in the tailings through high rates of Pi-fertiliser addition. As a result, the possibility of P-toxicity in native plant species caused by the addition of soluble phosphate fertilizers would be minimal.

Application of atomic absorption spectrophotometry to determine Cd, Cu, Pb, Zn,...in vegetable samples in Dalat

Energy Technology Data Exchange (ETDEWEB)

Giang, Nguyen; Tam, Nguyen Thanh; Ngoc Trinh, Le Thi; Mai, Truong Phuong; Minh, Nguyen Van [Nuclear Research Institute, Dalat (Viet Nam)

2004-08-01

Nowadays atomic absorption spectrometry has become valuable method for trace element analysis because high specificity; low detection litmus, easy to use; easy sample preparation, low investment and running costs... atomic absorption spectrometry is generally accepted as one the most suitable method for single - element analysis of trace elements in various kinds of materiel. In 2003, we applied flame - atomic absorption spectrometry for analyzing Ca, Cd, Cu, Pb, Zn...in vegetables and their extracted juices were collected form 11 locations of Dalat, including two kinds of vegetables (goods and safety) in both the summer and winter. Average concentration of Ca = 240 mg/kg wet, Cd = 0.035 mg/kg wet, Cu = 0.67 mg/kg wet, Mg = 131 mg/kg wet, Fe = 8.1/kg wet, Mn = 3.1/kg wet, Na = 3266 mg/kg wet, Pb = 0.345 mg/kg wet and Zn = 3.3 mg wet. In their extracted juices: Ca = 89 mg/kg wet, Cd = 0.008 mg/kg wet, Cu = 0.19 mg/kg wet, Mg = 43 mg/kg wet, Fe = 2.3 mg/kg wet, Mn = 0.61 mg/kg wet, Na = 971 mg/kg wet, Pb = 0.107 mg/kg wet and Zn = 0.65 mg/kg wet. (author)

Application of atomic absorption spectrophotometry to determine Cd, Cu, Pb, Zn,...in vegetable samples in Dalat

International Nuclear Information System (INIS)

Nguyen Giang; Nguyen Thanh Tam; Le Thi Ngoc Trinh; Truong Phuong Mai; Nguyen Van Minh

2004-01-01

Nowadays atomic absorption spectrometry has become valuable method for trace element analysis because high specificity; low detection litmus, easy to use; easy sample preparation, low investment and running costs... atomic absorption spectrometry is generally accepted as one the most suitable method for single - element analysis of trace elements in various kinds of materiel. In 2003, we applied flame - atomic absorption spectrometry for analyzing Ca, Cd, Cu, Pb, Zn...in vegetables and their extracted juices were collected form 11 locations of Dalat, including two kinds of vegetables (goods and safety) in both the summer and winter. Average concentration of Ca = 240 mg/kg wet, Cd = 0.035 mg/kg wet, Cu = 0.67 mg/kg wet, Mg = 131 mg/kg wet, Fe = 8.1/kg wet, Mn = 3.1/kg wet, Na = 3266 mg/kg wet, Pb = 0.345 mg/kg wet and Zn = 3.3 mg wet. In their extracted juices: Ca = 89 mg/kg wet, Cd = 0.008 mg/kg wet, Cu = 0.19 mg/kg wet, Mg = 43 mg/kg wet, Fe = 2.3 mg/kg wet, Mn = 0.61 mg/kg wet, Na = 971 mg/kg wet, Pb = 0.107 mg/kg wet and Zn = 0.65 mg/kg wet. (author)

Preparation of Mn-Zn nanoferrite by mechanical alloying

International Nuclear Information System (INIS)

Nasresfahani, M.

2007-01-01

Full text: In this research Mn-Zn nanoferrite (Mn x Zn 1-x Fe 2 O 4 ;X=0.3,0.5,0.7)were prepared by mechanical alloying of a mixture of 2 single phase ferrites, MnFe 2 O 4 and ZnFe 2 O 4 . First, ZnFe 2 O 4 and MnFe 2 O 4 were obtained by conventional ceramic technique. In this technique a mixture of related raw materials(ZnO and MnO 2 from merck company and Fe 2 O 3 domestic source) was first mixed and calcined at 1100 C for 3h in air. The starting materials used to prepare Mn-Zn nanoferrite were MnFe 2 O 4 and ZnFe 2 O 4 mixed in the ratio appropriate for the reaction: xMnFe 2 O 4+(1-x) ZnFe 2 O 4 MnxZn 1-x Fe 2 O 4 and milled at different times in SPEX8000M mixer/mill. XRD investigations was used to study the phase formation of the as-milled mixed ferrite. Using XRD patterns and Scherrer's formula, mean crystallite size of the single phase samples were calculated and were in the 10-20 nm. Saturation magnetization(Ms) of the powders was measured at room temperature by a very sensitive home made permeameter. The measured Ms values show that they are smaller than the Ms values associated with the same compound prepared by conventional ceramic technique. The decrease is due to the surface effect in nanoparticles, which can be explained on core-sell model. (authors)

Assessment Of Heavy Metal Contamination Of Water Sources From Enyigba Pb-Zn District South Eastern Nigeria

Directory of Open Access Journals (Sweden)

Nnabo Paulinus N

2015-08-01

Full Text Available Abstract A total of thirty 30 water samples were collected from the Enyigba PbZn mining district to assess the contamination of the water sources as a result of mining of lead and zinc minerals in the area. This comprises of 12 samples of surface water 14 from mine ponds and 4 from underground borehole water. The samples were acidified to stabilize the metals for periods more than four days without the use of refrigeration. The acidified water samples were analysed by a commercial laboratory at Projects Development Institute PRODA Enugu using Atomic Absorption Spectroscopy AAS. The elements determined by this method are lead Pb zinc Zn copper Cu arsenic As cadmium Cd nickel Ni manganese Mn and cobalt Co. The result and analysis of contamination factor showed that in surface water Cd had the highest concentration followed by As and Pb while Ni had the lowest. In mine ponds Cd also had the highest concentration and followed by Pb and As and Ni the lowest. In borehole water Cd has the highest concentration followed by Pb and As while Ni had the lowest concentration. Compared to WHO permissible limits the contamination of the heavy metals in all water sources are in order CdAsPbNiZnCu. In surface water the order is CdAsPbNiZnCu in mine ponds it is CdPbAsNiZnCu and in borehole water the order is CdAsPbZnNiCu. The calculated contamination factors show very high contamination status for Cd Pb and As. These levels of contamination and values indicate that under the prevailing conditions and environmental regulations in Nigeria the mining district would face major and hazardous discharges of these metals to the water sources.

Metal speciation in agricultural soils adjacent to the Irankuh Pb-Zn mining area, central Iran

Science.gov (United States)

Mokhtari, Ahmad Reza; Roshani Rodsari, Parisa; Cohen, David R.; Emami, Adel; Dehghanzadeh Bafghi, Ali Akbar; Khodaian Ghegeni, Ziba

2015-01-01

Mining activities are a significant potential source of metal contamination of soils in surrounding areas, with particular concern for metals dispersed into agricultural area in forms that are bioavailable and which may affect human health. Soils in agricultural land adjacent to Pb-Zn mining operations in the southern part of the Irankuh Mountains contain elevated concentrations for a range of metals associated with the mineralization (including Pb, Zn and As). Total and partial geochemical extraction data from a suite of 137 soil samples is used to establish mineralogical controls on ore-related trace elements and help differentiate spatial patterns that can be related to the effects of mining on the agricultural land soils from general geological and environmental controls. Whereas the patterns for Pb, Zn and As are spatially related to the mining operations they display little correlation with the distribution of secondary Fe + Mn oxyhydroxides or carbonates, suggesting dispersion as dust and in forms with limited bioavailability.

Evolution of electrical properties and domain configuration of Mn modified Pb(In1/2Nb1/2)O3-PbTiO3 single crystals

Science.gov (United States)

Qiao, Huimin; He, Chao; Yuan, Feifei; Wang, Zujian; Li, Xiuzhi; Liu, Ying; Guo, Haiyan; Long, Xifa

2018-04-01

The acceptor doped relaxor-based ferroelectric materials are useful for high power applications such as probes in ultrasound-guided high intensity focused ultrasound therapy. In addition, a high Curie temperature is desired because of wider temperature usage and improved temperature stability. Previous investigations have focused on Pb(Mg1/3Nb2/3)O3-PbTiO3 and Pb(Zn1/3Nb2/3)O3-PbTiO3 systems, which have a ultrahigh piezoelectric coefficient and dielectric constant, but a relatively low Curie temperature. It is desirable to study the binary relaxor-based system with a high Curie temperature. Therefore, Pb(In1/2Nb1/2)O3-PbTiO3 (PINT) single crystals were chosen to study the Mn-doped influence on their electrical properties and domain configuration. The evolution of ferroelectric hysteresis loops for doped and virgin samples exhibit the pinning effect in Mn-doped PINT crystals. The relaxation behaviors of doped and virgin samples are studied by fit of the modified Curie-Weiss law and Volgel-Fucher relation. In addition, a short-range correlation length was fitted to study the behavior of polar nanoregions based on the domain configuration obtained by piezoresponse force microscopy. Complex domain structures and smaller short-range correlation lengths (100-150 nm for Mn-doped PINT and >400 nm for pure PINT) were obtained in the Mn-doped PINT single crystals.

Associations between standardized school performance tests and mixtures of Pb, Zn, Cd, Ni, Mn, Cu, Cr, Co, and V in community soils of New Orleans

International Nuclear Information System (INIS)

Zahran, Sammy; Mielke, Howard W.; Weiler, Stephan; Hempel, Lynn; Berry, Kenneth J.; Gonzales, Christopher R.

2012-01-01

In New Orleans a strong inverse association was previously identified between community soil lead and 4th grade school performance. This study extends the association to zinc, cadmium, nickel, manganese, copper, chromium, cobalt, and vanadium in community soil and their comparative effects on 4th grade school performance. Adjusting for poverty, food security, racial composition, and teacher-student ratios, regression results show that soil metals variously reduce and compress student scores. Soil metals account for 22%–24% while food insecurity accounts for 29%–37% of variation in school performance. The impact on grade point averages were Ni > Co > Mn > Cu ∼Cr ∼ Cd > Zn > Pb, but metals are mixtures in soils. The quantities of soil metal mixtures vary widely across the city with the largest totals in the inner city and smallest totals in the outer city. School grade point averages are lowest where the soil metal mixtures and food insecurity are highest. - Highlights: ► Mixtures of metals vary; largest totals in the inner city and lowest in the outer city. ► An inverse association between soil Pb and 4th grade school performance is known. ► Assuming the same exposure pathway, multiple metals are compared to performance. ► Soil metals account for 22%–24% of variation in school test performance. ► Soil metal plus food insecurity accounts for 54% of explained variance. - Controlling for potential confounding variables, the accumulation of metals (Pb, Zn, Cd, Ni, Mn, Cu, Cr, and Co) in neighborhood soils is significantly negatively associated with 4th grade school performance on standardized tests in New Orleans.

The Enrichment and Transfer of Heavy Metals for Two Ferns in Pb-Zn Tailing

Directory of Open Access Journals (Sweden)

Mai Jiajie

2017-01-01

Full Text Available The enrichment and transfer of 8 heavy metals of Equisetum ramosissimum and Pteris vittata growing naturally close to edge of the sewage pool in Bencun Pb-Zn Tailing, Eastern Guangdong were investigated. The results indicated that the pollution of Cd, Pb, Hg, Zn was very severe in this tailing, followed by Cu and Mn. The potential ecological risk of heavy metals was assessed to be very strong based on soil background values of Guangdong Province and at high risk according to criteria of the second grade State Soil Environmental Quality Standard, and Cd, Hg, Pb were the main factors leading to potential ecological risk. The content of 8 heavy metals in the two ferns did not reach critical content of hyperaccumulator, so neither of them was typical hyperaccumulator, but both had a certain tolerance to these heavy metal pollution. Underground parts of Pteris vittata had an enrichment coefficient above 1 and that of Equisetum ramosissimum had a value near 1, therefore the two ferns could be utilized as potential enrichment plants. The two ferns have strong adaptability to the tailing habitat and can be used as pioneers in ecological restoration of Pb-Zn tailings.

Solvent extraction of Ca2+, Ba2+, Cu2+, Zn2+, Cd2+, Pb2+, UO22+, Mn2+, Co2+ and Ni2+ into nitrobenzene using strontium dicarbol-lylcobaltate and tetra-tert-butyl p-tert-butylcalix[4]arene tetraacetate

Directory of Open Access Journals (Sweden)

E. MAKRLÍK

2008-12-01

Full Text Available The exchange extraction constants corresponding to the general equilibrium M2+(aq + SrL2+(nb D ML2+ (nb + Sr2+ (aq occurring in the two-phase water–nitrobenzene system (M2+ = Ca2+, Ba2+, Cu2+, Zn2+, Cd2+, Pb2+, UO22+, Mn2+, Co2+ or Ni2+; L = tetra-tert-butyl p-tert-butylcalix[4]arene tetraacetate; aq = aqueous phase; nb = nitrobenzene phase were evaluated from extraction experiments and -activity measurements. Furthermore, the stability constants of the ML2+ complexes in water saturated nitrobenzene were calculated; they were found to increase in the cation order Ba2+ < Mn2+ < Pb2+, Co2+ < Cu2+, Zn2+ < Cd2+, Ni2+ < UO22+ < Ca2+.

Synthesis and characterization of ZnO/ZnSe NWs/PbS QDs solar cell

Science.gov (United States)

Kamruzzaman, M.; Zapien, J. A.

2017-04-01

The capture of solar energy has gained the attention for the next generation solar cell. ZnO/ZnSe NW arrays were synthesized on an FTO glass substrate using a simple and facile hydrothermal and ion-exchange approaches. The lead sulfide (PbS) QDs was infiltrated into ZnO/ZnSe NWs via SILAR method for making inorganic quantum dot sensitized ZnO/ZnSe/PbS QDs solar cell. The surface morphology, structural, optical, and J-V characteristics have been investigated. The ZnO/ZnSe NW is a core-shell like structure, and the absorption edge shifted from the UV region (ZnO NWs) to the near infrared region for ZnO/ZnSe NWs/PbS QDs. For PbS QDs-sensitized solar cell, the obtained value of η = 1.1%, J sc = 20.60 mA/cm2, V oc = 155 mV, and FF = 34.7%, respectively. The photovoltaic performance of the device in this study is still inferior. However, it is the first report regarding to ZnO/ZnZe NWs/PbS QDs solar cell. The achieving high absorption and large short circuit current density may interest in further improvement of the device performance by suppressing surface defects, optimizing the quality of ZnO/ZnSe NWs and PbS QDs.

Synthesis and characterization of ZnO/ZnSe NWs/PbS QDs solar cell

Energy Technology Data Exchange (ETDEWEB)

Kamruzzaman, M, E-mail: kzaman.phy11@gmail.com; Zapien, J A, E-mail: apjazs@cityu.edu.hk [City University of Hong Kong, Department of Physics and Materials Science and Center Of Super-Diamond and Advanced Films (COSDAF) (China)

2017-04-15

The capture of solar energy has gained the attention for the next generation solar cell. ZnO/ZnSe NW arrays were synthesized on an FTO glass substrate using a simple and facile hydrothermal and ion-exchange approaches. The lead sulfide (PbS) QDs was infiltrated into ZnO/ZnSe NWs via SILAR method for making inorganic quantum dot sensitized ZnO/ZnSe/PbS QDs solar cell. The surface morphology, structural, optical, and J-V characteristics have been investigated. The ZnO/ZnSe NW is a core–shell like structure, and the absorption edge shifted from the UV region (ZnO NWs) to the near infrared region for ZnO/ZnSe NWs/PbS QDs. For PbS QDs-sensitized solar cell, the obtained value of η = 1.1%, J{sub sc} = 20.60 mA/cm{sup 2}, V{sub oc} = 155 mV, and FF = 34.7%, respectively. The photovoltaic performance of the device in this study is still inferior. However, it is the first report regarding to ZnO/ZnZe NWs/PbS QDs solar cell. The achieving high absorption and large short circuit current density may interest in further improvement of the device performance by suppressing surface defects, optimizing the quality of ZnO/ZnSe NWs and PbS QDs.

Synthesis and characterization of Mn-doped ZnO column arrays

International Nuclear Information System (INIS)

Yang Mei; Guo Zhixing; Qiu Kehui; Long Jianping; Yin Guangfu; Guan Denggao; Liu Sutian; Zhou Shijie

2010-01-01

Mn-doped ZnO column arrays were successfully synthesized by conventional sol-gel process. Effect of Mn/Zn atomic ratio and reaction time were investigated, and the morphology, tropism and optical properties of Mn-doped ZnO column arrays were characterized by SEM, XRD and photoluminescence (PL) spectroscopy. The result shows that a Mn/Zn atomic ratio of 0.1 and growth time of 12 h are the optimal condition for the preparation of densely distributed ZnO column arrays. XRD analysis shows that Mn-doped ZnO column arrays are highly c-axis oriented. As for Mn-doped ZnO column arrays, obvious increase of photoluminescence intensity is observed at the wavelength of ∼395 nm and ∼413 nm, compared to pure ZnO column arrays.

Synthesis and characterization of Mn-doped ZnO diluted magnetic semiconductors

Energy Technology Data Exchange (ETDEWEB)

Abdel-Galil, A. [Solid State Physics and Accelerators Department, NCRRT, Atomic Energy Authority, Cairo (Egypt); Balboul, M.R., E-mail: m_balboul@yahoo.com [Solid State Physics and Accelerators Department, NCRRT, Atomic Energy Authority, Cairo (Egypt); Sharaf, A. [Radiation Engineering Department, NCRRT, Atomic Energy Authority, Cairo (Egypt)

2015-11-15

In the present work undoped and Mn doped ZnO nanoparticles (ZnO:Mn), diluted magnetic semiconductors, were successfully synthesized by the sol–gel method at room temperature. The morphology of ZnO nanoparticles constituted by flower-like structures with hexagonal morphologies that changed significantly after the incorporation of Mn. Rietveld refinements results showed that Mn ions are successfully doped into ZnO matrix without altering its wurtzite phase. Meanwhile, Raman spectroscopy analyses confirm the wurtzite structure of undoped ZnO and ZnO:Mn nanoparticles. The lattice parameters increase with increasing Mn content due to the large ionic radius of Mn{sup 2+} compared to that of Zn{sup 2+}. Electron spin resonance measurements were performed to gain information about oxidation state and site occupancy of the magnetic Mn ions in the ZnO lattice. Moreover, UV–vis absorption spectra have been utilized to calculate the optical band gap of the undoped ZnO and ZnO:Mn nanoparticles before and after different γ-irradiation doses. The band gap of ZnO:Mn (2%) is 2.62 eV which is noticeably smaller than the 3.26 eV of undoped ZnO. The thermal decomposition properties of the prepared nanoparticle samples were also studied using simultaneous Thermogravimetric analysis in temperature range from 30 to 500 °C.

Characterization of Mn doped ZnO nanopowder

Energy Technology Data Exchange (ETDEWEB)

Schlenker, Eva; Bakin, Andrey; Al-Suleiman, Mohamed; Wehmann, Hergo-Heinrich; Waag, Andreas [Institute of Semiconductor Technology, TU Braunschweig (Germany); Schmid, Herbert; Mader, Werner [Institute for Inorganic Chemistry, University Bonn (Germany); Bremers, Heiko; Hangleiter, Andreas [Institute of Applied Physics, TU Braunschweig (Germany)

2008-07-01

In the quest of materials for spintronic applications, diluted magnetic semiconductors recently attracted much attention. The main challenge is finding a ferromagnetic material with Curie temperature T{sub c}>300 K whose magnetic properties can be controlled electrically. The interest was particularly focused on Zn(TM)O since theoretical calculations predict that ZnO containing Mn could exhibit ferromagnetism with T{sub c} above room temperature. In the present study, the structural and magnetic properties of Mn doped ZnO nanopowder are investigated and compared to undoped ZnO crystals. Doping of ZnO with Mn results in increased lattice constants as revealed by XRD. However, an inhomogeneous distribution of the Mn dopants within the nanopowder was revealed by energy-dispersive X-ray and electron energy-loss spectroscopy. Magnetic properties are investigated by means of SQUID measurements on aggregates of powder particles as well as by MFM to study the behavior of single grains. The MFM image differs significantly from the topography as imaged by AFM and suggests the existence of long-ranging magnetic signals emerging from the sample.

Magnetic behavior of Co–Mn co-doped ZnO nanoparticles

International Nuclear Information System (INIS)

Li, Hengda; Liu, Xinzhong; Zheng, Zhigong

2014-01-01

Here, we report on systematic studies of the magnetic properties of Co and Mn co-doped ZnO nanoparticles prepared by a sol–gel technique. The effect of the concentration of the doping ions on the magnetic properties of Co and Mn co-doped ZnO nanoparticles is presented. X-ray diffraction characterizations (XRD) of co-doped ZnO nanoparticles are all wurtzite structure. The Zn 0.96 Co 0.02 Mn 0.02 O nanoparticles and Zn 0.94 Co 0.02 Mn 0.04 O nanoparticles display ferromagnetic behavior at room temperature. Superconducting quantum interference device (SQUID) magnetometer figures show that with the concentration of the Mn ions increased, the saturation magnetic moment (M s ) increased, and the magnetic is probably due to the co-doping of the Mn ions. Our results demonstrate that the Mn ions doping concentration play an important role in the ferromagnetic properties of Co–Mn co-doped ZnO nanoparticles at room temperature. - Highlights: • The effect of the doping ions on the magnetic properties is presented. • The magnetic is probably due to the co-doping of the Mn ions. • The Mn ions concentration play an important role in the ferromagnetic properties

Photoluminescence of ZnS: Mn quantum dot by hydrothermal method

Directory of Open Access Journals (Sweden)

Yun Hu

2018-01-01

Full Text Available ZnS: Mn quantum dots (QDs with the average grain size from 4.2 to 7.2 nm were synthesized by a hydrothermal method. All samples were cubic zinc blende structure (β-ZnS measured using X-ray diffraction (XRD. And the main diffraction peaks of ZnS: Mn shifted slightly towards higher angle in comparison with the intrinsic ZnS because of the substitution of Mn2+ for Zn2+. Due to the small grain size (4-7 nm effect, the poor dispersion and serious reunion phenomenon for the samples were observed from transmission electron microscopy (TEM. ZnS: Mn QDs had four peaks centered at 466, 495, 522, and 554 nm, respectively, in the photoluminescence (PL spectra, in which the band at 554 nm absent in the intrinsic ZnS: Mn is attributed to the doping of Mn2+ in the lattice sites. As the concentration of Mn2+ increasing from 0% to 0.6 at%, the intensity of the PL emission also increased. But the concentration reached 0.9 at%, quenching of PL emission occurred. The peak in ZnS: Mn QDs observed at 490 cm-1 was originated from the stretching vibration of the Mn–O bonds in the Fourier transform infrared (FTIR spectra. And the small changes about this peak compared with the previous reports at 500 cm-1 can be attributed to the formation of quantum dots. This method we utilized to synthesize ZnS: Mn QDs is very simple, low cost, and applicable for other semiconductor QD materials.

Effects of EDTA on phytoextraction of heavy metals (Zn, Mn and Pb) from sludge-amended soil with Brassica napus.

Science.gov (United States)

Zaier, Hanen; Ghnaya, Tahar; Ben Rejeb, Kilani; Lakhdar, Abdelbasset; Rejeb, Salwa; Jemal, Fatima

2010-06-01

Sludge application is a reliable practice to ameliorate soil fertility. However, repetitive sludge addition represents a potential soil contamination source with heavy metals, which must be extracted. The aim of this study was to evaluate the capacity of Brassica napus to remove metals from soils amended with sludge, and to study the effect of EDTA on this process. Seedlings were cultivated in presence of sludge combined or not with EDTA. Results showed that sludge ameliorate significantly biomass production. This effect was accompanied with an increase in Pb, Zn and Mn shoot concentrations. EDTA application does not affect significantly plant growth. However, this chelator enhances shoot metals accumulation. It's therefore concluded that sludge has a beneficial effect on soil fertility, B. napus can be used for the decontamination of affected soils and that the EDTA addition increases the ability of B. napus to accumulate heavy metals. Published by Elsevier Ltd.

Resonantly enhanced spin-lattice relaxation of Mn2 + ions in diluted magnetic (Zn,Mn)Se/(Zn,Be)Se quantum wells

Science.gov (United States)

Debus, J.; Ivanov, V. Yu.; Ryabchenko, S. M.; Yakovlev, D. R.; Maksimov, A. A.; Semenov, Yu. G.; Braukmann, D.; Rautert, J.; Löw, U.; Godlewski, M.; Waag, A.; Bayer, M.

2016-05-01

The dynamics of spin-lattice relaxation in the magnetic Mn2 + ion system of (Zn,Mn)Se/(Zn,Be)Se quantum-well structures are studied using optical methods. Pronounced cusps are found in the giant Zeeman shift of the quantum-well exciton photoluminescence at specific magnetic fields below 10 T, when the Mn spin system is heated by photogenerated carriers. The spin-lattice relaxation time of the Mn ions is resonantly accelerated at the cusp magnetic fields. Our theoretical analysis demonstrates that a cusp occurs at a spin-level mixing of single Mn2 + ions and a quick-relaxing cluster of nearest-neighbor Mn ions, which can be described as intrinsic cross-relaxation resonance within the Mn spin system.

Strong sp-d exchange coupling in ZnMnTe/ZnMgTe core/shell nanowires

Energy Technology Data Exchange (ETDEWEB)

Wojnar, Piotr; Janik, Elzbieta; Szymura, Malgorzata; Zaleszczyk, Wojciech; Kret, Slawomir; Klopotowski, Lukasz; Wojciechowski, Tomasz; Baczewski, Lech T.; Wiater, Maciej; Karczewski, Grzegorz; Wojtowicz, Tomasz; Kossut, Jacek [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, 02-668 Warsaw (Poland); Suffczynski, Jan; Papierska, Joanna [Institute of Experimental Physics, Warsaw University, ul. Hoza 69, 00-681 Warsaw (Poland)

2014-07-15

In this work, our recent progress in the growth and optical studies of telluride nanowire heterostructures containing a small molar fraction of magnetic Mn-ions of only a few percent is overviewed. ZnMnTe/ZnMgTe core/shell nanowires (NWs) are grown by molecular beam epitaxy by employing the vapor-liquid-solid growth mechanism assisted with gold catalyst. The structures are studied by means of photoluminescence and microphotoluminescence in an external magnetic field. In the first step, however, an activation of the near band edge emission from ZnTe and ZnMnTe nanowires is described, which is achieved by coating the nanowires with shells made of ZnMgTe. The role of these shells is to passivate Zn(Mn)Te surface states. The incorporation of Mn ions into the crystalline lattice of ZnMnTe nanowires is manifested as a considerable blue shift of near band edge emission with increasing Mn concentration inside the nanowire cores, which reflects directly the increase of their energy gap. In an external magnetic field the near band edge emission exhibits a giant spectral redshift accompanied by an increase of the circular polarization of the emitted light. Both effect are fingerprints of giant Zeeman splitting of the band edges due to sp-d exchange interaction between the band carriers and magnetic Mn-ions. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

One-pot synthesis of stable water soluble Mn:ZnSe/ZnS core/shell quantum dots

Energy Technology Data Exchange (ETDEWEB)

Zhang Hao; Gao Xue; Liu Siyu; Su Xingguang, E-mail: suxg@jlu.edu.cn [College of Chemistry, Jilin University, Department of Analytical Chemistry (China)

2013-06-15

In this paper, Mn:ZnSe/ZnS core/shell-doped quantum dots (d-dots) with 3-mercaptopropionic acid as the stabilizer are successfully synthesized through a simple one-pot synthesis procedure in aqueous solution. The average diameter of Mn:ZnSe/ZnS core/shell d-dots is about 2.9 nm, which is lager than that of Mn:ZnSe cores (about 1.9 nm). The optical features and structure of the obtained Mn:ZnSe/ZnS core/shell quantum dots have been characterized by UV-Vis and fluorescence spectroscopy, X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy. The photostability against UV irradiation and chemical stability against H{sub 2}O{sub 2} etching have been studied, and the results showed that the prepared Mn:ZnSe/ZnS core/shell d-dots are more stable than CdTe quantum dots prepared in aqueous solution. Finally, the resulting core/shell quantum dots are used as fluorescent label in human osteoblast-like HepG2 cell imaging.

Certification of trace element contents (As, Cd, Co, Cu, Fe, Mn, Hg, Na, Pb and Zn) in a fly ash obtained from the combustion of pulverised coal

International Nuclear Information System (INIS)

Griepink, B.; Colinet, E.; Guzzi, G.; Haemers, L.; Muntau, H.

1983-01-01

The element contents of As, Cd, Co, Cu, Fe, Mn, Hg, Na, Pb and Zn of a fly ash from pulverised coal are certified. The procedures and their results for the homogenisation, the contamination and homogeneity checks and the analytical campaign are reported. The certified mass fractions and indicative values for Cr, Ni, Th, V and water soluble sulphate are given. The work was carried out within the framework of the activities of the Community Bureau of Reference (BCR) of the Commission of the European Communities. (orig.) [de

Magnetic phase change in Mn-doped ZnSnAs2 thin films depending on Mn concentration

Science.gov (United States)

Uchitomi, Naotaka; Hidaka, Shiro; Saito, Shin; Asubar, Joel T.; Toyota, Hideyuki

2018-04-01

The relationship between Mn concentration and Curie temperature (TC) is studied for Mn-doped ZnSnAs2 ferromagnetic semiconductors, epitaxially grown on InP substrates by molecular beam epitaxy. In the ferromagnetic phase, Mn distributions in a (Zn,Mn,Sn)As2 thin film with 7.2 cation percent (cat. %) Mn are investigated using three-dimensional atom probe tomography. The results indicate an inhomogeneous distribution which spreads to a relatively high Mn concentration of 9.0 at. % (at. %). In the paramagnetic phase, it is found that the paramagnetic to ferromagnetic transition takes place sharply with a TC of 334 K when the Mn doping concentration increases to about 4 cat. % Mn, which corresponds to a magnetic percolation threshold for ferromagnetism in (Zn,Mn,Sn)As2. An effective Curie temperature ⟨TC⟩ is considered to bridge the Curie temperatures obtained experimentally to those calculated theoretically in inhomogeneous magnetic semiconductors. The behavior of magnetism in Mn-doped ZnSnAs2 can be explained by three different phases within the present framework.

Effect of ZnO and PbO/ZnO on structural and thermal properties of tellurite glasses

International Nuclear Information System (INIS)

Ramamoorthy, Raj Kumar; Bhatnagar, Anil K

2015-01-01

Highlights: • Structural units/linkages variation of TeO 2 -ZnO and TeO 2 -ZnO-PbO glasses was studied. • Structural arrangements of TeO 2 -ZnO glasses are rich in Te-O-Te network. • A mixture of Te-O-Te and Te-O-Pb networks is identified in TeO 2 -ZnO-PbO glasses. • Changes in thermal parameters T g and T o are correlated with the structural variations. • 15PbO and 20PbO samples of TeO 2 -ZnO-PbO glasses show large thermal stability. - Abstract: Two series of glasses, (100 − x)TeO 2 -xZnO (x = 20, 25, 30, 35) and 70TeO 2 -(30 − y)ZnO-yPbO (y = 5, 10, 15, 20), referred as TZ and TZP, respectively, were prepared by a melt quenching technique and characterized by X-ray diffraction (XRD), density, refractive index, Raman scattering and differential scanning calorimetry (DSC) to observe the changes in their properties as a function of ZnO and PbO/ZnO. Variations in individual structural units/linkages in these glasses are derived from the de-convoluted Raman spectra. The glass transition (T g ) and onset of crystallization (T o ) temperatures are determined from DSC isothermal scans. It is observed that the thermal stability (ΔT = T o − T g ) decreases for TZ glasses with increase in x, while it increases for TZP glasses with increase in y. Changes in thermal parameters of these glasses are correlated with the structural variation as a function of ZnO and PbO/ZnO ratio to determine the effect of substitution/addition of metal oxide, ZnO and PbO, to TeO 2 and TeO 2 -ZnO glasses

Magnetic properties in (Mn,Fe)-codoped ZnO nanowire

International Nuclear Information System (INIS)

Cao, Huawei; Lu, Pengfei; Cong, Zixiang; Yu, Zhongyuan; Cai, Ningning; Zhang, Xianlong; Gao, Tao; Wang, Shumin

2013-01-01

Using the first-principles density functional theory, we have studied the electronic structures and magnetic properties of Mn/Fe codoped ZnO nanowires systematically. The calculated results of formation energy indicate that the configuration of the lowest energy where Mn and Fe atoms form nearest neighbors on the outer cylindrical surface layer along the [0001] direction, will be determined. The magnetic coupling of 8 types of Mn/Fe codoped ZnO nanowires was investigated and ferromagnetic state was found in certain configurations. The mechanism is from the fierce hybridization between 3d of Mn and Fe with O 2p near the Fermi level. The relative energy difference for configuration VIII is 0.221 eV, which indicates that room temperature ferromagnetism could be obtained in such a system and Mn/Fe codoped ZnO nanowires are a promising nanoscale spintronic material. - Highlights: • The stable structure prefers that Mn/Fe form nearest neighbors on the outer surface. • The fierce p–d hybridization is responsible for ferromagnetic (FM) coupling. • Mn/Fe codoped ZnO nanowire is a promising FM semiconductor material

Magnetic properties in (Mn,Fe)-codoped ZnO nanowire

Energy Technology Data Exchange (ETDEWEB)

Cao, Huawei [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, Beijing 100876 (China); Lu, Pengfei, E-mail: photon.bupt@gmail.com [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, Beijing 100876 (China); Cong, Zixiang [School of Information and Communication Engineering, Beijing University of Posts and Telecommunications, Beijing 100976 (China); Yu, Zhongyuan; Cai, Ningning; Zhang, Xianlong [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, Beijing 100876 (China); Gao, Tao [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); Wang, Shumin [Photonics Laboratory, Department of Microtechnology and Nanoscience, Chalmers University of Technology, 41296 Gothenburg (Sweden); State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China)

2013-12-02

Using the first-principles density functional theory, we have studied the electronic structures and magnetic properties of Mn/Fe codoped ZnO nanowires systematically. The calculated results of formation energy indicate that the configuration of the lowest energy where Mn and Fe atoms form nearest neighbors on the outer cylindrical surface layer along the [0001] direction, will be determined. The magnetic coupling of 8 types of Mn/Fe codoped ZnO nanowires was investigated and ferromagnetic state was found in certain configurations. The mechanism is from the fierce hybridization between 3d of Mn and Fe with O 2p near the Fermi level. The relative energy difference for configuration VIII is 0.221 eV, which indicates that room temperature ferromagnetism could be obtained in such a system and Mn/Fe codoped ZnO nanowires are a promising nanoscale spintronic material. - Highlights: • The stable structure prefers that Mn/Fe form nearest neighbors on the outer surface. • The fierce p–d hybridization is responsible for ferromagnetic (FM) coupling. • Mn/Fe codoped ZnO nanowire is a promising FM semiconductor material.

Adsorpsi Pb2+ dan Zn2+ pada Biomassa Imperata cylindrica

Directory of Open Access Journals (Sweden)

Noer Komari

2017-03-01

Full Text Available Metode alternatif untuk mengatasi pencemaran logam berat adalah biosorpsi menggunakan biomassa sebagai adsorben. Telah dilakukan penelitian kajian adsorpsi campuran Pb2+ dan Zn2+ pada biomassa Imperata cylindrica sebagai adsorben. Tujuan penelitian adalah mengetahui kemampuan biomassa mengadsorpsi Pb2+ dan Zn2+. Preparasi biomassa dilakukan dengan aktivasi menggunakan asam nitrat dan amonium hidroksida. Adsorpsi dilakukan dengan sistem batch. Parameter yang diukur adalah pH optimum, waktu kontak optimum, kapasitas adsorpsi dan recovery ion logam. Analisis kadar logam dilakukan dengan menggunakan Spektrofotometer Serapan Atom (AAS. Hasil penelitian menunjukkan pH optimum adsorpsi Pb2+ dan Zn2+ masing-masing pada pH 5 dan pH 6. Waktu kontak optimum adsorpsi Pb2+ dan Zn2+ masing masing pada 40 menit dan 30 pertama. Kapasitas adsorpsi Pb2+ dan Zn2+ pada konsentrasi awal 10 ppm masing-masing adalah 90,95% dan 43,60%. Recovery Pb2+ dan Zn2+ masing-masing 84,45% dan 57,13%.

Contamination assessment of heavy metals in the soils around Khouzestan Steel Company (KSC (Ni, Mn, Pb, Fe, Zn, Cr

Directory of Open Access Journals (Sweden)

Fatemeh hormozi Nejad

2017-02-01

Full Text Available Introduction Soil plays a vital role in human life as the very survival of mankind is tied to the preservation of soil productivity (Kabata- Pendies and Mukherjee, 2007. The purpose of this study is the assessment of heavy metal contamination (Zn, Mn, Pb, Fe, Ni, Cr of the soil around the Khuzestan Steel Complex. Materials and methods For this purpose, 13 surface soil samples (0-10 cm were taken. Also a control sample was taken from an area away from the steel complex. The coordinates of each point were recorded by Global Positioning System (GPS. The samples were transferred to the laboratory and then were air dried at room temperature for 72 hours. Then they were sieved through a 2mm sieve for determining physical and chemical parameters (soil texture, pH, OC, and a 63-micron sieve for measurement of heavy metal concentration. pH was measured using a calibrated pH meter at a 2: 1 mixture (soil: water, and soil texture was determined using a hydrometer. The amount of organic matter was measured using the Valkey black method (Chopin and Alloway, 2007. After preparation of the samples in the laboratory, the samples were analyzed using the ICP-OES method to assess concentration of heavy metals. Measurement of heavy metals concentration was carried out at the Zar azma laboratory in Tehran. To ensure the accuracy of the analysis of soil samples, replicate samples were also sent to the laboratory. In order to assess the heavy metal pollution in the soil samples, different indices including contamination factor (CF, contamination degree (Cd, anthropogenic enrichment percent (An%, and saturation degree of metals (SDM were calculated. Discussion In addition, the mean concentrations of heavy metals in soil samples were compared to the concentration of these metals in Control Sample and unpolluted soil standard. Measurement of soil pH showed that the soil has a tendency to alkalinity. Also, soil texture is sandy loam (Moyes, 2011. The results showed that

Properties of Mn-doped ZnO nanopowder

Energy Technology Data Exchange (ETDEWEB)

Schlenker, E.; Bakin, A.; Wehmann, H.H.; Al-Suleiman, M.; Waag, A. [Technical University Braunschweig, Institute of Semiconductor Technology, Braunschweig (Germany); Schmid, H.; Mader, W. [Universitaet Bonn, Institut fuer Anorganische Chemie, Bonn (Germany); Bremers, H.; Hangleiter, A. [Technical University Braunschweig, Institute of Applied Physics, Braunschweig (Germany); Luedke, J.; Albrecht, M. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany)

2008-06-15

The structural and magnetic properties of Mn-doped ZnO nanopowder are investigated and compared to undoped ZnO crystals. Mn incorporation leads to an increase in the lattice constants as revealed by X-ray diffraction measurements. An inhomogeneous distribution of the Mn atoms within the nanopowder was detected by energy-dispersive X-ray and electron-energy-loss spectroscopy measurements. Magnetic features are investigated by means of SQUID magnetometry on ensembles of powder particles as well as by magnetic force microscopy to study the behavior of single grains. (orig.)

Moessbauer study of Mn-Zn and Mn ferrites prepared by wet method

International Nuclear Information System (INIS)

Michalk, C.

1985-01-01

Moessbauer spectroscopy was employed to study Mn-Zn ferrites before and after low-temperature annealing. The unannealed Mn-Zn ferrite prepared by a wet method and also the sintered material after annealing at 400 deg C in air show the presence of paramagnetic clusters. These findings are explained as being due to nonrandom ordering of Fe 3+ and Zn 2+ ions caused by local charge compensation in the neighbourhood of cation vacancies. A change of cation distribution after annealing at relatively low temperatures was observed. 10 refs., 3 figs. (author)

Facile fabrication and electrochemical behaviors of Mn:ZnS nanocrystals

International Nuclear Information System (INIS)

Xie, Ruishi; Li, Yuanli; Liu, Haifeng; Guo, Baogang

2016-01-01

Here, we demonstrate the rational design and synthesis of Mn:ZnS nanocrystals with adjustable doping concentrations utilizing a facile, cost effective, and environmentally benign chemical protocol. These nanostructures were investigated as electrode materials for lithium-ion batteries. Compared with pristine ZnS nanocrystals, the Mn:ZnS nanocrystals exhibit significantly improved electrochemical performances in terms of specific capacity and cycling performance. The Mn:ZnS nanocrystal sample with doping concentration of 1 at% displays second discharge capacity of 789.9 mA h g"−"1 at a current density of 24 mA g"−"1, about 2.39 times higher than that of the pure ZnS nanocrystal. Furthermore, the Mn:ZnS nanocrystal electrodes represent much better capacity retention than that of the undoped one. The greatly improved electrochemical performances of the Mn:ZnS nanocrystal samples could be attributed to the following factors. The large specific surface area can significantly enhance structural integrity by acting as mechanical buffer, effectively alleviating the volume changes generated during the lithiation/delithiation process. The incorporation of Mn into the lattice of ZnS improves charge transfer kinetics and results in a faster Li"+ diffusion rate during the charge–discharge process. It is of great significance to incorporate guest metal ions into nanostructured materials to display especial electrochemical characteristics triggering an effective approach to improve the electrochemical properties.

Facile fabrication and electrochemical behaviors of Mn:ZnS nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Xie, Ruishi [Analytical and Testing Center, Southwest University of Science and Technology, Mianyang, 621010 (China); Li, Yuanli, E-mail: yuanlyl@foxmail.com [Department of Materials, Southwest University of Science and Technology, Mianyang, 621010 (China); Liu, Haifeng; Guo, Baogang [Analytical and Testing Center, Southwest University of Science and Technology, Mianyang, 621010 (China)

2016-07-05

Here, we demonstrate the rational design and synthesis of Mn:ZnS nanocrystals with adjustable doping concentrations utilizing a facile, cost effective, and environmentally benign chemical protocol. These nanostructures were investigated as electrode materials for lithium-ion batteries. Compared with pristine ZnS nanocrystals, the Mn:ZnS nanocrystals exhibit significantly improved electrochemical performances in terms of specific capacity and cycling performance. The Mn:ZnS nanocrystal sample with doping concentration of 1 at% displays second discharge capacity of 789.9 mA h g{sup −1} at a current density of 24 mA g{sup −1}, about 2.39 times higher than that of the pure ZnS nanocrystal. Furthermore, the Mn:ZnS nanocrystal electrodes represent much better capacity retention than that of the undoped one. The greatly improved electrochemical performances of the Mn:ZnS nanocrystal samples could be attributed to the following factors. The large specific surface area can significantly enhance structural integrity by acting as mechanical buffer, effectively alleviating the volume changes generated during the lithiation/delithiation process. The incorporation of Mn into the lattice of ZnS improves charge transfer kinetics and results in a faster Li{sup +} diffusion rate during the charge–discharge process. It is of great significance to incorporate guest metal ions into nanostructured materials to display especial electrochemical characteristics triggering an effective approach to improve the electrochemical properties.

Mn{sup 2+} ions distribution in doped sol–gel deposited ZnO films

Energy Technology Data Exchange (ETDEWEB)

Stefan, Mariana, E-mail: mstefan@infim.ro [National Institute of Materials Physics, P.O. Box MG-7, 077125 Magurele (Romania); Ghica, Daniela; Nistor, Sergiu V.; Maraloiu, Adrian V. [National Institute of Materials Physics, P.O. Box MG-7, 077125 Magurele (Romania); Plugaru, Rodica [National Institute for R & D in Microtechnologies (IMT), Erou Iancu Nicolae Str. 126A, 077190 Bucharest (Romania)

2017-02-28

Highlights: • Several Mn{sup 2+} centers observed by EPR in sol–gel ZnO films. • Mn{sup 2+} ions localized at Zn{sup 2+} sites in ZnO grains and disordered ZnO phase. • Sixfold coordinated Mn{sup 2+} ions localized in inter-grain region. • Aggregated Mn in insular-like regions between ZnO grains in the ZnO:5%Mn film. • Aggregated Mn phase presence and distribution observed by EPR and EDX-STEM. - Abstract: The localization and distribution of the Mn{sup 2+} ions in two sol–gel deposited ZnO films doped with different manganese concentrations were investigated by electron paramagnetic resonance spectroscopy and analytical transmission electron microscopy. In the lightly doped sample the Mn{sup 2+} ions are mainly localized substitutionally at isolated tetrahedrally coordinated Zn{sup 2+} sites in both crystalline ZnO nanograins (34%) and surrounding disordered ZnO (52%). In the highly doped ZnO film, a much smaller proportion of manganese substitutes Zn{sup 2+} in the crystalline and disordered ZnO (10%). The main amount (85%) of manganese aggregates in a secondary phase as an insular-like distribution between the ZnO nanograins. The remaining Mn{sup 2+} ions (14% and 5% at low and high doping levels, respectively) are localized at isolated, six-fold coordinated sites, very likely in the disordered intergrain region. Annealing at 600 °C induced changes in the Mn{sup 2+} ions distribution, reflecting the increase of the ZnO crystallization degree, better observed in the lightly doped sample.

Magnetic exchange interactions in Mn doped ZnSnAs{sub 2} chalcopyrite

Energy Technology Data Exchange (ETDEWEB)

Bouhani-Benziane, H.; Sahnoun, O. [Laboratoire de Physique Quantique de la Matière et Modélisation Mathématique (LPQ3M), University of Mascara (Algeria); Sahnoun, M., E-mail: sahnoun_cum@yahoo.fr [Laboratoire de Physique Quantique de la Matière et Modélisation Mathématique (LPQ3M), University of Mascara (Algeria); Department of Chemistry, University of Fribourg (Switzerland); Driz, M. [Laboratoire de Sciences des Matériaux (LSM), University of Sidi Bel Abbes (Algeria); Daul, C. [Department of Chemistry, University of Fribourg (Switzerland)

2015-12-15

Accurate ab initio full-potential augmented plane wave (FP-LAPW) electronic calculations within generalized gradient approximation have been performed for Mn doped ZnSnAs{sub 2} chalcopyrites, focusing on their electronic and magnetic properties as a function of the geometry related to low Mn-impurity concentration and the spin magnetic alignment (i.e., ferromagnetic vs antiferromagnetic). As expected, Mn is found to be a source of holes and localized magnetic moments of about 4 µ{sub B} per Mn atom are calculated which are sufficiently large. The defect calculations are firstly performed by replacing a single cation (namely Zn and Sn) with a single Mn atom in the pure chalcopyrite ZnSnAs{sub 2} supercell, and their corresponding formation energies show that the substitution of a Sn atom (rather than Zn) by Mn is strongly favored. Thereafter, a comparison of total energy differences between ferromagnetic (FM) and antiferromagnetic (AFM) are given. Surprisingly, the exchange interaction between a Mn pairs is found to oscillate with the distance between them. Consequently, the AFM alignment is energetically favored in Mn-doped ZnSnAs{sub 2} compounds, except for low impurity concentration associated with lower distances between neighboring Mn impurities, in this case the stabilization of FM increases. Moreover, the ferromagnetic alignment in the Mn-doped ZnSnAs{sub 2} systems behaves half-metallic; the valence band for majority spin orientation is partially filled while there is a gap in the density of states for the minority spin orientation. This semiconducting gap of ~1 eV opened up in the minority channel and is due to the large bonding–antibonding splitting from the p–d hybridization. Our findings suggest that the Mn-doped ZnSnAs{sub 2} chalcopyrites could be a different class of ferromagnetic semiconductors. - Highlights: • ab initio calculations were performed on Mn doped ZnSnAs{sub 2} chalcopyrite. • Substitution of a Sn atom (rather than Zn) by Mn

New perovskite-based manganite Pb2Mn2O5

International Nuclear Information System (INIS)

Hadermann, Joke; Abakumov, Artem M.; Perkisas, Tyche; D'Hondt, Hans; Tan Haiyan; Verbeeck, Johan; Filonenko, Vladimir P.; Antipov, Evgeny V.; Van Tendeloo, Gustaaf

2010-01-01

A new perovskite based compound Pb 2 Mn 2 O 5 has been synthesized using a high pressure high temperature technique. The structure model of Pb 2 Mn 2 O 5 is proposed based on electron diffraction, high angle annular dark field scanning transmission electron microscopy and high resolution transmission electron microscopy. The compound crystallizes in an orthorhombic unit cell with parameters a=5.736(1) A∼√2a p , b=3.800(1) A∼a p , c=21.562(6) A∼4√2a p (a p -the parameter of the perovskite subcell) and space group Pnma. The Pb 2 Mn 2 O 5 structure consists of quasi two-dimensional perovskite blocks separated by 1/2[110] p (101) p crystallographic shear planes. The blocks are connected to each other by chains of edge-sharing MnO 5 distorted tetragonal pyramids. The chains of MnO 5 pyramids and the MnO 6 octahedra of the perovskite blocks delimit six-sided tunnels accommodating double chains of Pb atoms. The tunnels and pyramidal chains adopt two mirror-related configurations ('left' L and 'right' R) and layers consisting of chains and tunnels of the same configuration alternate in the structure according to an -L-R-L-R-sequence. The sequence is sometimes locally violated by the appearance of -L-L- or -R-R-fragments. A scheme is proposed with a Jahn-Teller distortion of the MnO 6 octahedra with two long and two short bonds lying in the a-c plane, along two perpendicular orientations within this plane, forming a d-type pattern. - Graphical abstract: Order of the Jahn-Teller distorted MnO 6 octahedra in Pb 2 Mn 2 O 5 . Two long and two short bonds lie in the a-c plane, along two perpendicular orientations within this plane, forming a d-type pattern.

Mixed Zn and O substitution of Co and Mn in ZnO

CERN Document Server

Pereira, Lino Miguel da Costa; Decoster, Stefan; Correia, João Guilherme; Amorim, Lígia Marina; da Silva, Manuel Ribeiro; Araújo, João Pedro; Vantomme, André

2011-01-01

The physical properties of an impurity atom in a semiconductor are primarily determined by the lattice site it occupies. In general, this occupancy can be correctly predicted based on chemical intuition, but not always. We report on one such exception in the dilute magnetic semiconductors Co- and Mn-doped ZnO, experimentally determining the lattice location of Co and Mn using $\\beta$-emission channeling from the decay of radioactive $^{61}$Co and $^{56}$Mn implanted at the ISOLDE facility at CERN. Surprisingly, in addition to the majority substituting for Zn, we find up to 18% (27%) of the Co (Mn) atoms in O sites, which is virtually unaffected by thermal annealing up to 900 °C. We discuss how this anion site configuration, which had never been considered before for any transition metal in any metal oxide material, may in fact have a low formation energy. This suggests a change in paradigm regarding transition-metal incorporation in ZnO and possibly other oxides and wide-gap semiconductors.

Mechanical, spectral, and luminescence properties of ZnS:Mn doped PDMS

Energy Technology Data Exchange (ETDEWEB)

Fontenot, Ross S. [University of Louisiana at Lafayette, Department of Physics, PO Box 44210, Lafayette, LA 70504 (United States); Allison, Stephen W., E-mail: steve.allison@emergingmeasurements.com [Emerging Measurements, Collierville, TN 38017 (United States); Lynch, Kyle J, E-mail: kjlynch@memphis.edu [Department of Physics, University of Memphis, Memphis, TN 38152 (United States); Hollerman, William A. [University of Louisiana at Lafayette, Department of Physics, PO Box 44210, Lafayette, LA 70504 (United States); Sabri, Firouzeh, E-mail: fsabri@memphis.edu [Department of Physics, University of Memphis, Memphis, TN 38152 (United States)

2016-02-15

Zinc sulfide doped with manganese (ZnS:Mn) is one of the brightest triboluminescent materials known and has been studied for a variety of applications. The powder form of this material restricts its safe handling and utilization, which limits the range of applications that can take advantage of its unique properties. In this study, the tribo- and photo-luminescent properties as well as the mechanical properties of ZnS:Mn encapsulated in an inert and optically transparent elastomer – Sylgard 184, have been investigated and fully characterized. ZnS:Mn particles of 8.5 µm diameter were incorporated into the Sylgard 184 polymer matrix prior to the curing stage with increasing amounts targeting a final (mass) concentration of 5%, 15%, and 50%. Additionally, the effect of the ZnS:Mn particles on the overall surface properties of the encapsulating elastomer was investigated and reported here. It was observed that the triboluminescent emission from impact scales with phosphor concentration and was not affected by the encapsulating medium. - Highlights: • Polymer encapsulation effects on the luminescent properties of ZnS:Mn was investigated. • Sylgard 184 encapsulated with ZnS:Mn (5, 15, 50 wt%) were characterized. • The triboluminescent emission from impact, scales with phosphor concentration. • Effect of the elastomeric medium on luminescent properties of ZnS:Mn was determined. • The work presented here demonstrates the feasibility of ZnS:Mn-based flexible sensors.

MnZn-ferrites: Targeted Material Design for New Emerging Application Products

OpenAIRE

Zaspalis V. T.; Tsakaloudi V.; Kogias G.

2014-01-01

In this article the main characteristics for emerging MnZn-ferrite applications are described on the basis of the new demands they possess on the ferrite material development. A number of recently developed MnZn-ferrite materials is presented together with the main scientific principles lying behind their development. These include: (i) high saturation flux density MnZn-ferrites (i.e. Bsat=550 mT at 10 kHz, 1200 A/m, 100°C), (ii) low power losses MnZn-ferrites (i.e. Pv~210 mW cm-3 at 100 kHz,...

Growth and electrical properties of (Mn,F) co-doped 0.92Pb(Zn 1/3Nb 2/3)O 3-0.08PbTiO 3 single crystal

Science.gov (United States)

Zhang, Shujun; Lebrun, Laurent; Randall, Clive A.; Shrout, Thomas R.

2004-06-01

The growth and characterization of (Mn,F) doped Pb(Zn 1/3Nb 2/3)O 3-PbTiO 3 (PZNT) single crystals are reported in this paper. The typical single crystal obtained is up to 30 mm size with dark brown color. The crystal lattice parameters of doped PZNT crystal are slightly decreased compared to the pure one. The room temperature dielectric permittivity along direction is about 6000, which is lower than that of the pure PZNT8 because of the dopants. The Curie temperature of the doped crystal is about 180°C while the ferroelectric phase transition temperature is around 100°C, which are higher than those of the pure PZNT8 single crystal. The remnant polarization and coercive field of oriented doped crystal measured at 1 Hz and 10 kV/cm field are about 27 μC/cm 2 and 4.2 kV/cm, respectively. The room temperature mechanical quality factor is ˜300. Piezoelectric coefficient of oriented doped crystal is higher than 3500 pC/N and the longitudinal electromechanical coupling factor is larger than 93%. The piezoelectric properties of doped PZNT single crystal with temperature and orientations are also reported in this paper. The valence state of the manganese dopant was determined by electron spin resonance, indicating no Mn 4+ in the crystals, suggesting the valence of manganese ions in PZNT crystals may be 2+, which acts as a hardener, stabilizes the domain wall and pins the domain wall motion, on the other hand, the dopant will enter Ti 4+ position, shifting the crystal composition to higher PT content.

Soil-plant abstract of heavy metals in Pb-Zn mining sites from Alcudia Valley (South Spain)

Science.gov (United States)

López-Berdonces, Miguel; Higueras, Pablo; Esbrí, Jose Maria; González-Corrochano, Beatríz; García-Noguero, Eva Mª; Martínez-Coronado, Alba; Fernandez-Calderón, Sergio; García-Noguero, Carolina

2013-04-01

Soil-plant transfer of heavy metals in Pb-Zn mining sites from Alcudia Valley (South Spain). Authors: Miguel A. López-Berdonces¹; Pablo Higueras¹; Jose María Esbrí¹; Beatriz González-Corrochano¹; Eva Mª García- Noguero¹; Alba Martínez Coronado¹; Sergio Fernández-Calderón¹; Carolina García-Noguero¹ ¹Instituto de Geología Aplicada, Universidad Castilla la Mancha, Pza. Manuel Meca, 1. 13400 Almadén, Spain. Alcudia Valley is a vast territory recently declared Natural Park, located in South of Spain. It is an area rich in mineral deposits of Zn and Pb and mining exists since the first millennium BC., having its highest ore production between mid-nineteenth century and the middle of the twentieth. This area has been selected because has more than 120 abandoned mines without remediation actions, with dumps and tailings with high contents of zinc and lead sulfides, and Cu, Ag, Cd, As, Sb in minor concentrations. In this study we determinate the transfer rate of these metals from soils to plants represented by oak leaves (Quercus ilex), because this specie is common within the selected area. To evaluate the soil-plant transfer were studied the correlation of contents, total and extractable, in soil-leaves. Extractable fraction was done by for different methods in water, EPA 1312 sulfuric acid: nitric acid 60:40 v., Ammonium Acetate and EDTA. To establish the correlation between heavy metals from soils to plants is necessary to know the contents of these and bioavailable content in soil. Three areas (S. Quintín, Romanilla, Bombita) were selected, taking 24 samples of soils and leaves. Analyzed leaves by XRF showed that Mn, Pb, Zn and Mo in S.Quintin and Romanilla, Mn, Pb in Bombita, exceeded the toxicity threshold. The same samples analyzed by ICP show us the toxicity threshold is exceeded Pb, Zn and Hg in S.Quintin, and Pb in Romanilla. The heavy metal content in leaves compared between two techniques analytical gives an acceptable correlation Zn - Pb

Magnetic properties of Mn-doped ZnO diluted magnetic semiconductors

International Nuclear Information System (INIS)

Liu Xuechao; Zhang Huawei; Zhang Tao; Chen Boyuan; Chen Zhizhan; Song Lixin; Shi Erwei

2008-01-01

A series of Mn-doped ZnO films have been prepared in different sputtering plasmas by using the inductively coupled plasma enhanced physical vapour deposition. The films show paramagnetic behaviour when they are deposited in an argon plasma. The Hall measurement indicates that ferromagnetism cannot be realized by increasing the electron concentration. However, the room-temperature ferromagnetism is obtained when the films are deposited in a mixed argon-nitrogen plasma. The first-principles calculations reveal that antiferromagnetic ordering is favoured in the case of the substitution of Mn 2+ for Zn 2+ without additional acceptor doping. The substitution of N for O (N O −) is necessary to induce ferromagnetic couplings in the Zn-Mn-O system. The hybridization between N 2p and Mn 3d provides an empty orbit around the Fermi level. The hopping of Mn 3d electrons through the empty orbit can induce the ferromagnetic coupling. The ferromagnetism in the N-doped Zn-Mn-O system possibly originates from the charge transfer between Mn 2+ and Mn 3+ via N O − . The key factor is the empty orbit provided by substituting N for O, rather than the conductivity type or the carrier concentration

HYDROTALSIT Zn-Al-EDTA SEBAGAI ADSORBEN UNTUK POLUTAN ION Pb(II DI LINGKUNGAN Zn-Al-EDTA Hydrotalcite as Adsorbent for Pb(II Ion Pollutant in The Environment

Directory of Open Access Journals (Sweden)

Roto Roto

2015-07-01

Full Text Available ABSTRAK Polusi ion Pb(II di dalam lingkungan perairan cenderung naik seiring peningkatan jumlah industri smelter dan daur ulang aki bekas. Penelitian ini bertujuan untuk menguji kemampuan hidrotalsit Zn-Al-EDTA sebagai adsorben ion Pb(II dalam air secara mendalam. Hidrotalsit Zn-Al-NO3 disintesis dengan metode kopresipitasi dan hidrotermal pada temperatur 100 °C selama 15 jam. Hidrotalsit Zn-Al-EDTA diperoleh dengan penukaran ion. Keasaman larutan, kinetika dan kapasitas adsorpsi diteliti. Hidrotalsit Zn-Al-EDTA memiliki d003 sebesar 14,52 Å sementara Zn-Al-NO3 sebesar 8,90 Å. Spektra FTIR menunjukkan keberadaan serapan gugus C=O pada bilangan gelombang 1684,77 cm-1. Kondisi optimum adsorpsi ion Pb(II terjadi pada pH 4, waktu kontak 60 menit dan kapasitas adsorpsi diperoleh 2,07 mg/g pada konsentrasi awal 10 mg/L dengan berat adsorben 0,100 g. Adsorpsi ion Pb(II oleh hidrotalsit Zn-Al-EDTA mengikuti reaksi pseudo orde dua dengan tetapan laju adsorpsi sebesar 8,90 g mmol-1min-1. Adsorpsi ion Pb(II oleh Zn-Al-EDTA terjadi karena  pembentukan khelat Pb-EDTA di dalam struktur hidrotalsit. Hasil ini diharapkan mampu memberikan kontribusi yang lebih luas di dalam pengendalian konsentrasi Pb(II di lingkungan. ABSTRACT Polution by Pb(II ion in the water environment tends to increase due the increase in the number of lead smelter and lead acid battery recycling industries. This work aims at studying in details the ability of Zn-Al-EDTA hydrotalcite as adsorbent for Pb(II ion in the environment. The Zn-Al-NO3 hydrotalcite was synthesized first by coprecipitation method followed by hydrothermal treatment at 100 °C for 15 h. The Zn-Al-EDTA hydrotalcite was later obtained by ion exchange process. The solution pH, kinetics and adsorption capacity were studied. The XRD data showed that Zn-Al-EDTA and Zn-Al-NO3 hydrotalcites have d003 of 14.52 and 8.90 Å, respectively. The FTIR spectra suggested that C=O group was observed with absorption band at 1684

Effects of the ZnO layer on the structure and white light emission properties of a ZnS:Mn/GaN nanocomposite system.

Science.gov (United States)

Wang, Cai-Feng; Hu, Bo

2017-10-01

ZnO films were inserted between the ZnS:Mn films and GaN substrates by pulsed laser deposition (PLD). The structure, morphology, and optical properties of the ZnS:Mn/ZnO/GaN nanocomposite systems have been investigated. X-ray diffraction results show that there are three diffraction peaks located at 28.4°, 34.4°, and 34.1°, which correspond to the β-ZnS(111), ZnO(002), and GaN(002) planes, respectively. Due to the insertion of ZnO films, the diffraction peak intensity of ZnS:Mn in ZnS:Mn/ZnO/GaN is stronger than that of ZnS:Mn in ZnS:Mn/GaN, and the full width at half-maximum is smaller. Though the transmittance of ZnS:Mn/ZnO films is slightly lower than that of ZnS:Mn films, the transmittance is still higher than 80%. Compared with ZnS:Mn/GaN, an ultraviolet (UV) emission at 387 nm (originated from the near-band emission of ZnO) and a green light emission at about 520 nm appeared in the photoluminescence (PL) spectra of ZnS:Mn/ZnO/GaN, in addition to the blue emission at 435 nm and the orange-red emission at 580 nm. The emission at 520 nm may be related to the deep-level emission from ZnO and the interface of ZnS:Mn/ZnO. The PL spectrum of ZnS:Mn/ZnO/GaN covers the visible region from the blue light to the red light (400-700 nm), and its color coordinate and color temperature are (0.3103,0.3063) and 6869 K, respectively, presenting strong white light emission.

One-step synthesis of PbSe-ZnSe composite thin film

Directory of Open Access Journals (Sweden)

Abe Seishi

2011-01-01

Full Text Available Abstract This study investigates the preparation of PbSe-ZnSe composite thin films by simultaneous hot-wall deposition (HWD from multiple resources. The XRD result reveals that the solubility limit of Pb in ZnSe is quite narrow, less than 1 mol%, with obvious phase-separation in the composite thin films. A nanoscale elemental mapping of the film containing 5 mol% PbSe indicates that isolated PbSe nanocrystals are dispersed in the ZnSe matrix. The optical absorption edge of the composite thin films shifts toward the low-photon-energy region as the PbSe content increases. The use of a phase-separating PbSe-ZnSe system and HWD techniques enables simple production of the composite package.

Materials for spintronic: Room temperature ferromagnetism in Zn-Mn-O interfaces

International Nuclear Information System (INIS)

Quesada, A.; Garcia, M.A.; Crespo, P.; Hernando, A.

2006-01-01

In this paper we study the room temperature ferromagnetism reported on Mn-doped ZnO and ascribed to spin polarization of conduction electrons. We experimentally show that the ferromagnetic behaviour is associated to the coexistence of Mn 3+ and Mn +4 in MnO 2 grains where diffusion of Zn promotes the Mn 4+→ Mn 3+ reduction. Potential uses of this material in spintronic devices are analysed

Thermally stimulated properties in ZnSe:Tb and ZnSe:(Mn, Tb) phosphors

Science.gov (United States)

Mishra, A. K.; Mishra, S. K.; Pandey, S. P.; Lakshmi Mishra, Kshama

2018-02-01

Thermoluminescence studies were performed of ZnSe:Tb and ZnSe:(Mn, Tb) phosphors. A method of preparation for ZnSe phosphors doped with Tb and (Mn, Tb) has been discussed. The thermoluminescence (TL) properties of these phosphors have been studied from 100 to 370 K temperature after exciting by UV radiation (365 nm) at three uniform heating rates 0.4, 0.6 and 0.9 K/s. The trapping parameters like trap depth, lifetime of electrons and capture cross-section have also been determined using various methods.

Succulent species differ substantially in their tolerance and phytoextraction potential when grown in the presence of Cd, Cr, Cu, Mn, Ni, Pb, and Zn.

Science.gov (United States)

Zhang, Chengjun; Sale, Peter W G; Clark, Gary J; Liu, Wuxing; Doronila, Augustine I; Kolev, Spas D; Tang, Caixian

2015-12-01

Plants for the phytoextraction of heavy metals should have the ability to accumulate high concentrations of such metals and exhibit multiple tolerance traits to cope with adverse conditions such as coexistence of multiple heavy metals, high salinity, and drought which are the characteristics of many contaminated soils. This study compared 14 succulent species for their phytoextraction potential of Cd, Cr, Cu, Mn, Ni, Pb, and Zn. There were species variations in metal tolerance and accumulation. Among the 14 succulent species, an Australian native halophyte Carpobrotus rossii exhibited the highest relative growth rate (20.6-26.6 mg plant(-1) day(-1)) and highest tolerance index (78-93%), whilst Sedum "Autumn Joy" had the lowest relative growth rate (8.3-13.6 mg plant(-1) day(-1)), and Crassula multicava showed the lowest tolerance indices (phytoextraction of these heavy metals than other species. These findings suggest that Carpobrotus rossii is a promising candidate for phytoextraction of multiple heavy metals, and the aquatic or semiterrestrial Crassula helmsii is suitable for phytoextraction of Cd and Zn from polluted waters or wetlands.

Quenching and blue shift of UV emission intensity of hydrothermally grown ZnO:Mn nanorods

Energy Technology Data Exchange (ETDEWEB)

Vinod, R. [Department of Physics, Cochin University of Science and Technology, Kochi 682022, Kerala (India); Junaid Bushiri, M., E-mail: junaidbushiri@gmail.com [Department of Physics, Cochin University of Science and Technology, Kochi 682022, Kerala (India); Achary, Sreekumar Rajappan; Muñoz-Sanjosé, Vicente [Departamento de FisicaAplicada y Electromagnetismo, Universitat de Valencia, c/Dr. Moliner 50, Burjassot, Valencia 46100 (Spain)

2015-01-15

Highlights: • Single crystalline ZnO:Mn nanorods. • Reduced optical active defects. • Quenching and blue shift of UV emission. - Abstract: ZnO:Mn alloyed nanorods (Mn nominal concentration – 3–5 wt%) were synthesized by using hydrothermal process at an optimized growth temperature of 200 °C and a growth time of 3 h. The XRD, SEM and Raman, FTIR investigations reveal that ZnO:Mn (Mn – 3–5 wt%) retained hexagonal wurtzite crystal structure with nanorod morphology. The HRTEM and SAED analysis confirm the single crystalline nature of hydrothermally grown ZnO and ZnO:Mn (5 wt%) nanorods. The ZnO:Mn nanorods (Mn – 0–5 wt%) displayed optical band gap in the range 3.23–3.28 eV. The blue shift of UV emission peak (PL) from 393 (ZnO) to 386 nm and quenching of photoluminescence emission in ZnO:Mn is due to the Mn incorporation in ZnO lattice. Relative increase in intensity of Raman band at 660 cm{sup −1} with nominal doping of Mn 3–5 wt% in ZnO indicate that defects are introduced in ZnO:Mn system as a result of doping that leads to the quenching of photoluminescence emission at 393 nm.

Mn-doped ZnO nanocrystals synthesized by sonochemical method: Structural, photoluminescence, and magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Othman, A.A., E-mail: aaelho@yahoo.com [Assiut University, Faculty of Science, Department of Physics, Assiut 71516 (Egypt); Osman, M.A. [Assiut University, Faculty of Science, Department of Physics, Assiut 71516 (Egypt); Ibrahim, E.M.M. [Sohag University, Faculty of Science, Department of Physics, Sohag 82524 (Egypt); Ali, Manar A.; Abd-Elrahim, A.G. [Assiut University, Faculty of Science, Department of Physics, Assiut 71516 (Egypt)

2017-05-15

Highlights: • Mn-doped ZnO nanostructures were synthesized by the sonochemical method. • Structural, morphological, optical, photoluminescence and magnetic properties were investigated. • Mn-doped ZnO nanostructures reveal a blue shift of the optical band gap. • Photoluminescence spectra of Mn-doped ZnO nanostructures show quenching in the emission intensity. • Mn-doped ZnO nanostructures exhibit ferromagnetic ordering at room temperature. - Abstract: This work reports the synthesis of Mn-doped ZnO nanostructures using ice-bath assisted sonochemical technique. The impact of Mn-doping on structural, morphological, optical, and magnetic properties of ZnO nanostructures is studied. The morphological study shows that the lower doped samples possess mixtures of nanosheets and nanorods while the increase in Mn content leads to improvement of an anisotropic growth in a preferable orientation to form well-defined edge rods at Mn content of 0.04. UV–vis absorption spectra show that the exciton peak in the UV region is blue shifted due to Mn incorporation into the ZnO lattice. Doping ZnO with Mn ions leads to a reduction in the PL intensity due to a creation of more non-radiative recombination centers. The magnetic measurements show that the Mn-doped ZnO nanostructures exhibit ferromagnetic ordering at room temperature, as well as variation of the Mn content can significantly affect the ferromagnetic behavior of the samples.

Electron lucky-drift impact ionization coefficients of ZnS : Mn

Indian Academy of Sciences (India)

can also be used to calculate the impact ionization coefficients of high electron energy of. ZnS:Mn without ... Electroluminescent devices (ZnS:Mn) recently are of great interest in industry as well as in information technology [1–4]. Understanding .... data in the case of electron in ZnS from two sources, which were reported by.

Studies of the interaction of CS@ZnS:Mn with bovine serum albumin under illumination

Energy Technology Data Exchange (ETDEWEB)

Liu, Li, E-mail: 2476625723@qq.com [Institute of Agricultural Quality Standards and Testing Technology Research, Hubei Academy of Agricultural Science, Wuhan 430064 (China); Xiao, Ling [School of Resource and Environmental Science, Hubei Biomass-Resource Chemistry and Environmental Biotechnology Key Laboratory, Wuhan University, Wuhan 430072 (China)

2015-09-15

Highlights: • The interaction and illumination damages of CS@ZnS:Mn D-dots to BSA were studied. • The quenching mechanism of CS@ZnS:Mn D-dots with BSA belongs to dynamic quenching. • The hydrophobic interaction plays a major role; the binding processes are spontaneous. • The FL enhancement of CS@ZnS:Mn D-dots by BSA under UV illumination was observed. • The probable mechanism is mainly a photo-induced free radical procedure. - Abstract: In this study, chitosan coated Mn-doped ZnS quantum dots (CS@ZnS:Mn D-dots) were obtained in aqueous media under ambient pressure. The interaction and illumination damages of CS@ZnS:Mn D-dots with bovine serum albumin (BSA) were studied by means of ultraviolet–visible (UV–vis) and fluorescence (FL) spectra. It was found that the FL of BSA was quenched by CS@ZnS:Mn D-dots. The dominating quenching mechanism of CS@ZnS:Mn D-dots with BSA belongs to dynamic quenching. Hydrophobic interaction plays a major role in the CS@ZnS:Mn–BSA interaction; binding processes are spontaneous. Influencing factors such as illumination time and CS@ZnS:Mn D-dots concentrations were considered. The FL quenching effect of BSA by CS@ZnS:Mn D-dots is enhanced with the increase of illumination time and CS@ZnS:Mn D-dots concentration. The FL enhancement of CS@ZnS:Mn D-dots by BSA under UV illumination was also observed. It was proved that, the interaction of CS@ZnS:Mn D-dots with BSA under UV illumination is mainly a result of a photo-induced free radical procedure. CS@ZnS:Mn D-dots may be used as photosensitizers in photodynamic therapy.

Studies of the interaction of CS@ZnS:Mn with bovine serum albumin under illumination

International Nuclear Information System (INIS)

Liu, Li; Xiao, Ling

2015-01-01

Highlights: • The interaction and illumination damages of CS@ZnS:Mn D-dots to BSA were studied. • The quenching mechanism of CS@ZnS:Mn D-dots with BSA belongs to dynamic quenching. • The hydrophobic interaction plays a major role; the binding processes are spontaneous. • The FL enhancement of CS@ZnS:Mn D-dots by BSA under UV illumination was observed. • The probable mechanism is mainly a photo-induced free radical procedure. - Abstract: In this study, chitosan coated Mn-doped ZnS quantum dots (CS@ZnS:Mn D-dots) were obtained in aqueous media under ambient pressure. The interaction and illumination damages of CS@ZnS:Mn D-dots with bovine serum albumin (BSA) were studied by means of ultraviolet–visible (UV–vis) and fluorescence (FL) spectra. It was found that the FL of BSA was quenched by CS@ZnS:Mn D-dots. The dominating quenching mechanism of CS@ZnS:Mn D-dots with BSA belongs to dynamic quenching. Hydrophobic interaction plays a major role in the CS@ZnS:Mn–BSA interaction; binding processes are spontaneous. Influencing factors such as illumination time and CS@ZnS:Mn D-dots concentrations were considered. The FL quenching effect of BSA by CS@ZnS:Mn D-dots is enhanced with the increase of illumination time and CS@ZnS:Mn D-dots concentration. The FL enhancement of CS@ZnS:Mn D-dots by BSA under UV illumination was also observed. It was proved that, the interaction of CS@ZnS:Mn D-dots with BSA under UV illumination is mainly a result of a photo-induced free radical procedure. CS@ZnS:Mn D-dots may be used as photosensitizers in photodynamic therapy

A Hollow-Structured Manganese Oxide Cathode for Stable Zn-MnO₂ Batteries.

Science.gov (United States)

Guo, Xiaotong; Li, Jianming; Jin, Xu; Han, Yehu; Lin, Yue; Lei, Zhanwu; Wang, Shiyang; Qin, Lianjie; Jiao, Shuhong; Cao, Ruiguo

2018-05-05

Aqueous rechargeable zinc-manganese dioxide (Zn-MnO₂) batteries are considered as one of the most promising energy storage devices for large scale-energy storage systems due to their low cost, high safety, and environmental friendliness. However, only a few cathode materials have been demonstrated to achieve stable cycling for aqueous rechargeable Zn-MnO₂ batteries. Here, we report a new material consisting of hollow MnO₂ nanospheres, which can be used for aqueous Zn-MnO₂ batteries. The hollow MnO₂ nanospheres can achieve high specific capacity up to ~405 mAh g −1 at 0.5 C. More importantly, the hollow structure of birnessite-type MnO₂ enables long-term cycling stability for the aqueous Zn-MnO₂ batteries. The excellent performance of the hollow MnO₂ nanospheres should be due to their unique structural properties that enable the easy intercalation of zinc ions.

A new insight of recycling of spent Zn-Mn alkaline batteries: Synthesis of Zn{sub x}Mn{sub 1−x}O nanoparticles and solar light driven photocatalytic degradation of bisphenol A using them

Energy Technology Data Exchange (ETDEWEB)

Qu, Jiao, E-mail: qujiao@bhu.edu.cn [School of Chemistry and Chemical Engineering, Bohai University, Jinzhou, Liaoning 121013 (China); School of Urban and Environmental Sciences, Northeast Normal University, Changchun, Jilin 130024 (China); Feng, Yue; Zhang, Qian [School of Chemistry and Chemical Engineering, Bohai University, Jinzhou, Liaoning 121013 (China); Cong, Qiao [School of Chemistry and Chemical Engineering, Bohai University, Jinzhou, Liaoning 121013 (China); School of Urban and Environmental Sciences, Northeast Normal University, Changchun, Jilin 130024 (China); Luo, Chunqiu [School of Chemistry and Chemical Engineering, Bohai University, Jinzhou, Liaoning 121013 (China); Yuan, Xing [School of Urban and Environmental Sciences, Northeast Normal University, Changchun, Jilin 130024 (China)

2015-02-15

Highlights: • Zn{sub 0.5}Mn{sub 0.5}O nanoparticles synthesized using SABs were cylinder with 60 nm diameter. • Adsorption equilibrium of BPA on Zn{sub x}Mn{sub 1−x}O nanoparticles were achieved in 40 min. • Decomposition yields of BPA were increased with light irradiation and Zn{sub x}Mn{sub 1−x}O nanoparticles. • The findings have positive effects on solving the recycling of SABs. - Abstract: This work focuses on the synthesis of Zn{sub 0.1}Mn{sub 0.9}O, Zn{sub 0.3}Mn{sub 0.7}O, and Zn{sub 0.5}Mn{sub 0.5}O nanoparticles using Zn-Mn spent alkaline batteries (SABs) as raw materials and their applications for photocatalytic degradation of bisphenol A in water. Zn-Mn SABs were manually dismantled into scrap (including plastics, copper cap, zinc crust, and carbon rod) and powder. The mashed zinc crust and pretreated powder were successively added into H{sub 2}SO{sub 4} and NH{sub 3}⋅H{sub 2}O, and the formed precipitates were characterized. The yield (wt) of synthesis of Zn{sub 0.5}Mn{sub 0.5}O (ZnMnO{sub 3}) nanoparticles was 57.1%. The synthesized Zn{sub 0.5}Mn{sub 0.5}O nanoparticles were cylinder, with a length of 60 nm. Afterwards, the removal efficiencies of bisphenol A (BPA) under solar light irradiation with the recovered Zn{sub x}Mn{sub 1−x}O nanoparticles were investigated: (1) the adsorption equilibrium of BPA on Zn{sub x}Mn{sub 1−x}O nanoparticles could be achieved after approximate 40 min. The saturation absorbance of BPA was about 32.40 ± 4.76 mg g{sup −1}, 20.40 ± 3.60 mg g{sup −1}, and 14.50 ± 4.55 mg g{sup −1} by Zn{sub 0.1}Mn{sub 0.9}O, Zn{sub 0.3}Mn{sub 0.7}O, and Zn{sub 0.5}Mn{sub 0.5}O nanoparticles, respectively; (2) compared with the 21.7 ± 1.6% degradation of BPA (only solar light irradiation for 180 min), the combination of solar light irradiation and Zn{sub 0.1}Mn{sub 0.9}O, Zn{sub 0.3}Mn{sub 0.7}O, and Zn{sub 0.5}Mn{sub 0.5}O nanoparticles could lead to 59.41 ± 4.32%, 83.43 ± 2.73%, and 71.22 ± 4

Obtainment of Hg-free Mn/Zn solutions from spent alkaline batteries; Obtencion de soluciones de Mn/Zn libres de Hg provenientes de pilas alcalinas gastadas

Energy Technology Data Exchange (ETDEWEB)

Perez-Nicolas, L.; Espinosa-Ramirez, I. [Instituto Politecnico Nacional, UPALM, Mexico, D.F. (Mexico)]. E-mail: lepeni@hotmail.com; Aguilar, M. [Instituto de Fisica, UNAM, Mexico, D.F. (Mexico); Palacios-Beas, E. [Instituto Politecnico Nacional, UPALM, Mexico, D.F. (Mexico)

2009-09-15

As in many other countries, the excessive consumption of alkaline batteries in Mexico has generated highly contaminating wastes, with heavy metal contents such as Mn, Zn, Fe, Hg, Cu and Ni, among others. This has caused a large degree of environmental degradation with repercussions for the health of living beings. Because there are no regulations regarding the disposal of spent batteries, they are thrown out with the rest of the domestic wastes or directly into nature, ending up in open-air landfills or containers where they are incinerated, thereby contaminating the planet's environment, soil and springs. The present work studies the obtainment of solutions of Hg-free Mn and Zn (Mn/Zn {>=} 1) from spent alkaline batteries for use in synthesis of (Mn,Zn)Fe{sub 2}O{sub 4} ferrite by a wet method. The effect is analyzed of the dissolution medium (H{sub 2}SO{sub 4}/H{sub 2}O{sub 2}, HCl and HCl/NO{sub 3}) temperature and time on the percentage of dissolution of the metals present in the electrode material, characterized by atomic absorption (AA) spectroscopy and x-ray diffraction (XRD). The results of the investigation indicate that the best dissolution conditions are MD=H{sub 2}SO{sub 4}/H{sub 2}O{sub 2}, T=50 degrees Celsius and t =30 min, where 94.1 and 90.7 % (w/w) of Mn and Zn are obtained, respectively, with Mn/Zn = 1.51. The mercury content was determined to be 3.91%, higher than that stated by the battery specifications, which is recovered by dissolving with HCl/HNO{sub 3} in the residual solid. [Spanish] En Mexico como en muchos otros paises, el consumo excesivo de pilas alcalinas ha generado desechos altamente contaminantes, con contenidos de metales pesados como Mn, Zn, Fe, Hg, Cu y Ni entre otros, que han provocado un gran deterioro en el medio ambiente repercutiendo en la salud de los seres vivos. Dado que no se tiene una regulacion en cuanto a la disposicion de pilas gastadas, estas se desechan con el resto de las residuos domesticos o directamente

[Stabilization Treatment of Pb and Zn in Contaminated Soils and Mechanism Studies].

Science.gov (United States)

Xie, Wei-qiang; Li, Xiao-mingi; Chen, Can; Chen, Xun-feng; Zhong, Yu; Zhong, Zhen-yu; Wan, Yong; Wang, Yan

2015-12-01

In the present work, the combined application of potassium dihydrogen phosphate, quick lime and potassium chloride was used to immobilize the Pb and Zn in contaminated soils. The efficiency of the process was evaluated through leaching tests and Tessier sequential extraction procedure. The mechanism of stabilization was analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM) to reveal the mechanism of stabilization. The results showed that the stabilizing efficiency of Pb contaminated soils was above 80% and the leaching concentrations of Pb, Zn were far below the threshold when the ratio of exogenous P and soil (mol · mol⁻¹) was 2:1-4: 1, the dosing ratio of CaO was 0.1%-0.5% ( mass fraction) and the dosage of potassium chloride was 0.02-0. 04 mol. Meanwhile, Pb and Zn in soil were transformed from the exchangeable fraction into residual fraction, which implied that the migration of Pb, Zn in soil could be confined by the stabilization treatment. XRD and SEM analysis revealed that Ca-P-Pb precipitation, lead orthophosphate [PbHP0₄, Pb₃ (PO₄)₂], pyromorphite (Pb-PO₄-Cl/OH) and mixed heavy metal deposits (Fe-PO₄- Ca-Pb-Zn-OH) could be formed after solidification/stabilization in which Pb and Zn could be wrapped up to form a solidified composition and to prevent leaching.

Structure and photoluminescence of Mn-passivated nanocrystalline ZnO:S thin films

International Nuclear Information System (INIS)

Tong, Y.H.; Tang, Q.X.; Liu, Y.C.; Shao, C.L.; Xu, C.S.; Liu, Y.X.

2005-01-01

Mn-passivated nanocrystalline ZnO:S thin films were fabricated by thermally oxidizing Mn-doped ZnS (ZnS:Mn) films prepared by electron beam evaporation. Mn was introduced to passivate the surface defects of ZnO and to improve the optical properties. X-ray diffraction (XRD) and photoluminescence (PL) spectra at 81.9 K indicated the S content in ZnO thin film gradually decreased with increasing annealing temperature. The fitted result of the temperature-dependent PL spectra in the range from 81.9 to 302.2 K showed that S dopant could broaden the optical band gap energy of ZnO. Room temperature PL spectra confirmed that the ultraviolet peak shifted to lower energy with the decrease of S content in the thin film because of the Burstein-Moss effect

Efficient photocatalytic degradation of malachite green dye under visible irradiation by water soluble ZnS:Mn/ZnS core/shell nanoparticles

Science.gov (United States)

Khaparde, Rohini A.; Acharya, Smita A.

2018-05-01

ZnS:Mn/ ZnS core/shell nanoparticles was prepared by two step synthesis method. In first step, oleic acid - coated Mn doped ZnS core nanoparticles were prepared which were charged through ligand exchange. Shell of ZnS NPs was finally deposited upon the surface of charged Mn doped ZnS core. Scanning electron microscopy (SEM) image exhibit morphological confirmation of ZnS:Mn/ZnS core/shell. As Nano ZnS are the most suitable candidates for photocatalyst that extensively involved in degradation and complete mineralization of various toxic organic pollutants owing to its high efficiency, strong oxidizing power, non-toxicity, high photochemical and biological stability, corrosive resistance and low cost. Photodegradation of malachite green is systematically investigated by adding different molar proportional of ZnS:Mn/ZnS core/shell in the dye. The rate of de-coloration of dye is detected by UV-VIS absorption spectroscopy. Efficient detoriation in the colour of dye is attributed to the core /shell morphology of the particles.

Absence of intrinsic ferromagnetism in Zn{sub 1-x}Mn{sub x}O alloys

Energy Technology Data Exchange (ETDEWEB)

Zhang Huawei [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Shi Erwei [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Chen Zhizhan [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Liu Xuechao [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Xiao Bing [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

2006-10-04

Zn{sub 1-x}Mn{sub x}O alloys, with different Mn concentrations, were prepared by the hydrothermal method. X-ray diffraction and electron paramagnetic resonance spectra demonstrate that Zn{sup 2+} ions are homogeneously substituted by Mn{sup 2+} ions without changing the ZnO wurtzite structure. The x = 0.02 and 0.04 samples are paramagnetic. When the Mn concentrations are increased to x = 0.08 and 0.10, the samples exhibit some ferromagnetism due to a secondary phase (Zn,Mn)Mn{sub 2}O{sub 4}. (letter to the editor)

Hydrothermal synthesis and magnetic properties of Mn doped ZnS nanoparticles

Science.gov (United States)

Rashad, M. M.; Rayan, D. A.; El-Barawy, K.

2010-01-01

Nanocrystallite Mn doped Zn1-XS (X = 0 to 0.4) powders have been synthesized through a hydrothermal route. The effect of the hydrothermal temperature and Mn2+ ions substitution on the crystal structure, crystallite size, microstructure and magnetic properties were investigated using (XRD), (SEM) and (VSM). The results revealed that wurtzite zinc sulfide phase was formed using thiourea as a sulfur source at temperature 150- 200oC for 24 h. The crystallite size was (7.9-15.1 nm) was obtained at the same conditions. The doping of Mn2+ ions decreased the crystallite size of the formed ZnS wurtzite phase was in the range between 7.9 and 3.8 nm. SEM micrographs showed that the produced ZnS and Mn doped ZnS particles were appeared as spherical shape. The magnetic properties were improved by substitution of Mn2+ ions up to 0.2.

Hydrothermal synthesis and magnetic properties of Mn doped ZnS nanoparticles

International Nuclear Information System (INIS)

Rashad, M M; Rayan, D A; El-Barawy, K

2010-01-01

Nanocrystallite Mn doped Zn 1-X S (X = 0 to 0.4) powders have been synthesized through a hydrothermal route. The effect of the hydrothermal temperature and Mn 2+ ions substitution on the crystal structure, crystallite size, microstructure and magnetic properties were investigated using (XRD), (SEM) and (VSM). The results revealed that wurtzite zinc sulfide phase was formed using thiourea as a sulfur source at temperature 150- 200 o C for 24 h. The crystallite size was (7.9-15.1 nm) was obtained at the same conditions. The doping of Mn 2+ ions decreased the crystallite size of the formed ZnS wurtzite phase was in the range between 7.9 and 3.8 nm. SEM micrographs showed that the produced ZnS and Mn doped ZnS particles were appeared as spherical shape. The magnetic properties were improved by substitution of Mn 2+ ions up to 0.2.

Structural refinement, photoluminescence and Raman spectroscopy of wurtzite Mn-doped Zn O pellets

Energy Technology Data Exchange (ETDEWEB)

Marquina, J.; Martin, J.; Luengo, J.; Vera, F.; Roa, L. [Centro de Estudios Avanzados en Optica, Universidad de los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Gonzalez, J. [Centro de Estudios de Semiconductores, Universidad de los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Rodriguez, F.; Renero L, C.; Valiente, R. [Malta-Consolider Team, CITIMAC, Facultad de Ciencias, Universidad de Cantabria, Santander 69005 (Spain); Delgado, G. E., E-mail: marquinajesus@gmail.com [Laboratorio de Cristalografia, Facultad de Ciencias, Universidad de los Andes, Merida 5101 (Venezuela, Bolivarian Republic of)

2017-11-01

We report the results of the Rietveld refinement, photoluminescence and Raman spectroscopy of Mn-doped Zn O ceramic pellets. Rietveld refinement shows that samples crystallize in the wurtzite structure and for the Mn-doped sample indicated that the Mn atoms substitute the Zn tetrahedral crystallographic sites in the Zn O host lattice. The emission and absorption spectra of Mn-doped Zn O have been investigated in the visible-UV region and the data have been interpreted in terms of the wurtzite Zn O electronic structure. Two broad bands, one due to superposition between donor bound excitons (DX) and free excitons (FX) and other due free-to bond excitonic recombination (FB) dominates the low-temperature photoluminescence spectra of Mn-doped Zn O bulk. In the Raman spectrum, an extra mode at ∼520 cm{sup -1} has been observed in agreement with earlier works, and it is an indicator for the incorporation of Mn{sup +2} ions into the Zn O host matrix since it is not is observed in Zn O pristine. Rietveld refinement of the X-ray diffraction patterns, energy-dispersive X-ray spectroscopy (EDS) technique, and Raman spectroscopies were performed to study these effects. (Author)

Properties of Mn0.4Zn0.6Fe2O4 and Mn0.6Zn0.4Fe2O4 as Nanocatalyst for Ammonia Production

Directory of Open Access Journals (Sweden)

Puspitasari Poppy

2017-01-01

Full Text Available Ammonia synthesis requires high pressure and high temperature process. Unfortunately, the capital intensive cost resulting low yield of ammonia by using recent catalyst which is iron oxide. Therefore, manganese zinc ferrite as a soft ferrite material will be introduced as a new nanocatalyst to enhance the ammonia yield. As a new nanocatalyst for ammonia production, study of comparasion two different concentration of MnZn Ferrite is very important. This paper will compare the yield of ammonia by using two different nanocatalyst which are Mn0.4Zn0.6Fe2O4 and Mn0.6Zn0.4Fe2O4. Both were synthesized by sol-gel method and has been characterize by using FESEM (morphology, XRD (phase identification, EDX (elemental analysis and TPR (oxide reduction. The ammonia was produce with and without magnetic field applied. The result shows that the ammonia yield is higher for Mn0.4Zn0.6Fe2O4 nanocatalyst than Mn0.6Zn0.4Fe2O4 by using magnetic field applied. 67.2% of yield has been achieved by using new nanocatalyst Mn0.6Zn0.4Fe2O4 and magnetic field applied at ambient environment.

Preparation of nanometer sized Mn doped Zn based oxides powder for DMS applications

CSIR Research Space (South Africa)

Das, J

2009-01-01

Full Text Available In order to study the size dependent DMS (Diluted Magnetic Semiconductor) behavior of Mn doped ZnO, the authors have systematically prepared a series of nanosized green powder based on Mn doped ZnO (Zn 1-x Mn x O, where x=0.02 - 0.1) materials using...

Energy-dispersive X-ray fluorescence analysis of traces of heavy metals (Mn, Fe, Co, Ni, Cu, Zn, Ta, Pb, U) in mineral waters after separation on the cellulose-exchanger Hyphan

International Nuclear Information System (INIS)

Burba, P.; Lieser, K.H.

1979-01-01

Trace elements in mineral water are separated in small columns on the cellulose-exchanger Hyphan, eluted by diluted hydrochloric acid, bound on 100 mg of Hyphan by shaking and determined by energy-dispersive X-ray fluorescence. The following heavy metals can be analysed quantitatively if present in water in concentrations >= 1 ppb: Mn, Fe, Co, Ni, Cu, Zn, Ta, Pb and U. Several commercial mineral waters, a sodium chloride spring and seawater were analyzed for trace elements. The results obtained by X-ray fluorescence and by atomic absorption agree within the limits of error. (orig.) [de

Synthesis and characterization of Mn2+-doped ZnS nanoparticles

Indian Academy of Sciences (India)

Keywords. Nanoparticles; nanocomposite; Mn2+-doped ZnS; annealing; X-ray diffrac- tion; FTIR; ultra violet. ... is an important wide band gap semiconductor, has attracted much attention owing to its wide applications ... semiconductor nanoparticles ZnS : Mn2+ is used as phosphors and also in thin film electroluminescent ...

Hydrothermal synthesis and magnetic properties of Mn doped ZnS nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Rashad, M M; Rayan, D A; El-Barawy, K [Central Metallurgical Research and Development Institute PO Box: 87 Helwan, Cairo (Egypt)

2010-01-01

Nanocrystallite Mn doped Zn{sub 1-X}S (X = 0 to 0.4) powders have been synthesized through a hydrothermal route. The effect of the hydrothermal temperature and Mn{sup 2+} ions substitution on the crystal structure, crystallite size, microstructure and magnetic properties were investigated using (XRD), (SEM) and (VSM). The results revealed that wurtzite zinc sulfide phase was formed using thiourea as a sulfur source at temperature 150- 200{sup o}C for 24 h. The crystallite size was (7.9-15.1 nm) was obtained at the same conditions. The doping of Mn{sup 2+} ions decreased the crystallite size of the formed ZnS wurtzite phase was in the range between 7.9 and 3.8 nm. SEM micrographs showed that the produced ZnS and Mn doped ZnS particles were appeared as spherical shape. The magnetic properties were improved by substitution of Mn{sup 2+} ions up to 0.2.

Qualitative aspects of biomonitoring: Sphagnum auriculatum response vs. aerosol metal concentrations (Pb, Ca, Cr, Cu, Fe, Mn, Ni and Zn) in the Porto urban atmosphere

International Nuclear Information System (INIS)

Teresa, M.; Vasconcelos, S.D.; Tavares Laquipai, H.M.F.

2000-01-01

and Zn were also biomonitored and monitored in parallel. For all the heavy metals, the rate of metal uptake by moss was significantly correlated with the metal concentration in atmospheric aerosols. The results indicated that moss bags of S. auriculatum can provide quantitative estimation of the concentration of different heavy metals in urban atmosphere since the present methodology is used. S. auriculatum showed not to be a good quantitative bioindicator for Ca. The mean aerosol metal concentrations found in Porto atmosphere were similar to those observed in other urban atmospheres in different countries. The relative order of the mean metal concentrations was Fe (1.8 μg/m 3 ) > Ca > Zn > Pb > Cu > Cr > Mn > Ni (20 μg/m 3 ). (author)

Bioleaching mechanism of Zn, Pb, In, Ag, Cd and As from Pb/Zn smelting slag by autotrophic bacteria.

Science.gov (United States)

Wang, Jia; Huang, Qifei; Li, Ting; Xin, Baoping; Chen, Shi; Guo, Xingming; Liu, Changhao; Li, Yuping

2015-08-15

A few studies have focused on release of valuable/toxic metals from Pb/Zn smelting slag by heterotrophic bioleaching using expensive yeast extract as an energy source. The high leaching cost greatly limits the practical potential of the method. In this work, autotrophic bioleaching using cheap sulfur or/and pyrite as energy matter was firstly applied to tackle the smelting slag and the bioleaching mechanisms were explained. The results indicated autotrophic bioleaching can solubilize valuable/toxic metals from slag, yielding maximum extraction efficiencies of 90% for Zn, 86% for Cd and 71% for In, although the extraction efficiencies of Pb, As and Ag were poor. The bioleaching performance of Zn, Cd and Pb was independent of leaching system, and leaching mechanism was acid dissolution. A maximum efficiency of 25% for As was achieved by acid dissolution in sulfursulfur oxidizing bacteria (S-SOB), but the formation of FeAsO4 reduced extraction efficiency in mixed energy source - mixed culture (MS-MC). Combined works of acid dissolution and Fe(3+) oxidation in MS-MC was responsible for the highest extraction efficiency of 71% for In. Ag was present in the slag as refractory AgPb4(AsO4)3 and AgFe2S3, so extraction did not occur. Copyright © 2015 Elsevier Ltd. All rights reserved.

Synthesis and Fluorescence Property of Mn-Doped ZnSe Nanowires

Directory of Open Access Journals (Sweden)

Dongmei Han

2010-01-01

Full Text Available Water-soluble Mn-doped ZnSe luminescent nanowires were successfully prepared by hydrothermal method without any heavy metal ions and toxic reagents. The morphology, composition, and property of the products were investigated. The experimental results showed that the Mn-doped ZnSe nanowires were single well crystallized and had a zinc blende structure. The average length of the nanowires was about 2-3 μm, and the diameter was 80 nm. With the increase of Mn2+-doped concentration, the absorbance peak showed large difference. The UV-vis absorbance spectrum showed that the Mn-doped ZnSe nanowires had a sharp absorption band appearing at 360 nm. The PL spectrum revealed that the nanowires had two distinct emission bands centered at 432 and 580 nm.

Microwave firing of MnZn-ferrites

International Nuclear Information System (INIS)

Tsakaloudi, V.; Papazoglou, E.; Zaspalis, V.T.

2004-01-01

Microwave firing is evaluated in comparison to conventional firing for MnZn-ferrites. For otherwise identical conditions, microwave firing results to higher densities and coarser microstructures. Initial magnetic permeability values (25 kHz, 25 deg. C, <0.1 mT) after conventional firing are approximately 5000, but the corresponding values after microwave firing are approximately 6000. Unlike the conventional firing process, the final density after microwave firing is increased by increasing the prefiring temperature. As appears from the results of this study, microwave firing could be in principle a promising MnZn-ferrite firing technology for materials to be used in high magnetic permeability applications. No advantages of microwave firing are evident for materials intended to be used in high field power applications

Synthesis and characterization of single-phase Mn-doped ZnO

Science.gov (United States)

Chattopadhyay, S.; Dutta, S.; Banerjee, A.; Jana, D.; Bandyopadhyay, S.; Chattopadhyay, S.; Sarkar, A.

2009-05-01

Different samples of Zn 1-xMn xO series have been prepared using conventional solid-state sintering method. We identified up to what extent doping will enable us to synthesize single-phase polycrystalline Mn-doped ZnO sample, which is one of the prerequisites for dilute magnetic semiconductor, and we have analyzed its some other physical aspects. In synthesizing the samples, proportion of Mn varies from 1 to 5 at%. However, the milling time varied (6, 12, 24, 48 and 96 h) only for 2 at% Mn-doped samples while for other samples (1, 3, 4 and 5 at% Mn doped) the milling time has been fixed to 96 h. Room-temperature X-ray diffraction (XRD) data reveal that all of the prepared samples up to 3 at% of Mn doping exhibit wurtzite-type structure, and no segregation of Mn and/or its oxides has been found. The 4 at% Mn-doped samples show a weak peak of ZnMn 2O 4 apart from the other usual peaks of ZnO and the intensity of this impurity peak has been further increased for 5 at% of Mn doping. So beyond 3 at% doping, single-phase behavior is destroyed. Band gap for all the 2 at% Mn-doped samples has been estimated to be between 3.21 and 3.19 eV and the reason for this low band gap values has been explained through the grain boundary trapping model. The room-temperature resistivity measurement shows an increase of resistivity up to 48 h of milling and with further milling it saturates. The defect state of these samples has been investigated using the positron annihilation lifetime (PAL) spectroscopy technique. Here all the relevant lifetime parameters of positron i.e. free annihilation ( τ1) at defect site ( τ2) and average ( τav) increases with milling time.

Synthesis and characterization of single-phase Mn-doped ZnO

International Nuclear Information System (INIS)

Chattopadhyay, S.; Dutta, S.; Banerjee, A.; Jana, D.; Bandyopadhyay, S.; Chattopadhyay, S.; Sarkar, A.

2009-01-01

Different samples of Zn 1-x Mn x O series have been prepared using conventional solid-state sintering method. We identified up to what extent doping will enable us to synthesize single-phase polycrystalline Mn-doped ZnO sample, which is one of the prerequisites for dilute magnetic semiconductor, and we have analyzed its some other physical aspects. In synthesizing the samples, proportion of Mn varies from 1 to 5 at%. However, the milling time varied (6, 12, 24, 48 and 96 h) only for 2 at% Mn-doped samples while for other samples (1, 3, 4 and 5 at% Mn doped) the milling time has been fixed to 96 h. Room-temperature X-ray diffraction (XRD) data reveal that all of the prepared samples up to 3 at% of Mn doping exhibit wurtzite-type structure, and no segregation of Mn and/or its oxides has been found. The 4 at% Mn-doped samples show a weak peak of ZnMn 2 O 4 apart from the other usual peaks of ZnO and the intensity of this impurity peak has been further increased for 5 at% of Mn doping. So beyond 3 at% doping, single-phase behavior is destroyed. Band gap for all the 2 at% Mn-doped samples has been estimated to be between 3.21 and 3.19 eV and the reason for this low band gap values has been explained through the grain boundary trapping model. The room-temperature resistivity measurement shows an increase of resistivity up to 48 h of milling and with further milling it saturates. The defect state of these samples has been investigated using the positron annihilation lifetime (PAL) spectroscopy technique. Here all the relevant lifetime parameters of positron i.e. free annihilation (τ 1 ) at defect site (τ 2 ) and average (τ av ) increases with milling time.

Photoluminescence characteristics of Pb-doped, molecular-beam-epitaxy grown ZnSe crystal layers

International Nuclear Information System (INIS)

Mita, Yoh; Kuronuma, Ryoichi; Inoue, Masanori; Sasaki, Shoichiro; Miyamoto, Yoshinobu

2004-01-01

The characteristic green photoluminescence emission and related phenomena in Pb-doped, molecular-beam-epitaxy (MBE)-grown ZnSe crystal layers were investigated to explore the nature of the center responsible for the green emission. The intensity of the green emission showed a distinct nonlinear dependence on excitation intensity. Pb-diffused polycrystalline ZnSe was similarly examined for comparison. The characteristic green emission has been observed only in MBE-grown ZnSe crystal layers with moderate Pb doping. The results of the investigations on the growth conditions, luminescence, and related properties of the ZnSe crystal layers suggest that the green emission is due to isolated Pb replacing Zn and surrounded with regular ZnSe lattice with a high perfection

Facile Synthesis of Porous ZnMnO3 Spherulites with a High Lithium Storage Capability

International Nuclear Information System (INIS)

Liu, Xinru; Zhao, Chenhao; Zhang, He; Shen, Qiang

2015-01-01

Graphical abstract: Porous ZnMnO 3 spherulites show an enhanced high lithium storage capability when potentially applied as a lithium-ion battery anode for the first time. - Highlights: • Composite Zn 0.5 Mn 0.5 CO 3 microspheres are facilely co-precipitated. • Porous ZnMnO 3 spherulites can be used as a lithium-ion battery anode. • Porous ZnMnO 3 spherulites show superior electrochemical properties. • A synergistic effect of Zn-O and Mn-O components in cubic ZnMnO 3 is proposed. - Abstract: In this paper, pure-phase ZnMnO 3 porous spherulites are uniquely synthesized through the thermal decomposition of Zn-Mn binary carbonate precursors facilely co-precipitated at room temperature, possessing an average diameter of 1.2 ± 0.3 μm and acquiring porosity with a specific surface area of 24.3 m 2 g −1 . When tentatively applied as lithium-ion battery anodes for the first time, these porous spherulites deliver an initial discharge capacity of 1294 mAh g −1 at 500 mA g −1 and retain an reversible value of 879 mAh g −1 over 150 cycles. By comparison, the equimolar powder mixture of nano-sized ZnO and MnO 2 synergistically shows a higher lithium storage capability than the two unary transition metal oxides, but lower than anode material ZnMnO 3 . Aside from its nanostructured characteristics, an inner atomic synergistic effect within the cubic lattices may account for the superior electrochemical performance of well-crystallized ZnMnO 3

Manufacturing of Mn-Zn ferrite transformer cores

International Nuclear Information System (INIS)

Waqas, H.; Qureshi, A.H.; Hussain, N.; Ahmed, N.

2012-01-01

The present work is related to the development of soft ferrite transformer cores, which are extensively used in electronic devices such as switch mode power supplies, electromagnetic devices, computers, amplifiers etc. Mn-Zn Ferrite (soft ferrite) powders were prepared by conventional mixed oxide and auto combustion routes. These powders were calcined and then pressed in toroid shapes. Sintering was done at different temperatures to develop desired magnetic phase. Impedance resistance of sintered toroid cores was measured at different frequencies. Results revealed that Mn-Zn Ferrite cores synthesized by auto combustion route worked more efficiently in a high frequency range i.e. > 2MHz than the cores developed by conventional mixed oxide method. It was noticed that compact size, light weight and high impedance resistance are the prime advantages of auto combustion process which supported the performance of core in MHz frequency range. Furthermore, these compact size cores were successfully tested in linear pulse amplifier circuit of Pakistan Atomic Research Reactor-I. The fabrication of soft ferrite (Mn-Zn Ferrite) cores by different processing routes is an encouraging step towards indigenization of ferrite technology. (Orig./A.B.)

Effect of foliar applied (Zn, Fe, Cu and Mn) in citrus production

International Nuclear Information System (INIS)

Khurshid, F.; Sarwar, S.; Khattak, R.A.

2008-01-01

A study was conducted to evaluate the impact of micronutrients (Zn, Fe, Cu and Mn) on sweet orange (Citrus Sinensis L.), blood red var., on farmer's orchard at Khanpur, district Haripur, NWFP, during 2002-03. Micronutrients were applied in foliar sprays over the canopy of each tree. The main effects and interactions of Zinc sulphate (Zn), iron sulphate (Fe), Copper Sulphate (Cu) and Manganese Sulphate (Mn) were studied in factorial combinations. A basal dose of nitrogen, phosphorus and potassium was applied at the rate 1.5, 1 and 1 kg tree/sup -1/. Zn, Fe, Cu and Mn were applied alone and in various combinations at the rate 0.115, 0.057, 0.05 and 0.13 kg in 100 liters of water. Application of micronutrients significantly increased Zn, Fe, Cu and Mn concentrations in leaves, compared with control. Zn treatments significantly increased the yield, number of fruit and total sugar. Manganese treatments significantly increased the total soluble solids and reduced the acidity of fruit juice. Other quality parameters, including fruit size, percent peel, percent pulp, sugar as well as total soluble solids, were improved with the application of Zn, Fe, Cu and Mn. (author)

Characterization of nanostructures of ZnO and ZnMnO films deposited by successive ionic layer adsorption and reaction method

Energy Technology Data Exchange (ETDEWEB)

Jimenez-Garcia, F.N. [Departamento de Fisica y Matematicas, Universidad Autonoma de Manizales, Antigua Estacion del Ferrocarril, Manizales, Caldas (Colombia); Departamento de Fisica y Quimica, Universidad Nacional de Colombia, Sede Manizales, Campus la Nubia, Manizales, Caldas (Colombia); Espinosa-Arbelaez, D.G. [Departamento de Nanotecnologia, Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, Blv. Juriquilla 3001, Juriquilla, Queretaro, C.P. 76230 (Mexico); Posgrado en Ciencia e Ingenieria Materiales, Instituto de Investigacion en Materiales, Universidad Nacional Autonoma de Mexico, Mexico DF (Mexico); Vargas-Hernandez, C. [Departamento de Fisica y Quimica, Universidad Nacional de Colombia, Sede Manizales, Campus la Nubia, Manizales, Caldas (Colombia); Real, A. del [Departamento de Nanotecnologia, Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, Blv. Juriquilla 3001, Juriquilla, Queretaro, C.P. 76230 (Mexico); Rodriguez-Garcia, M.E., E-mail: marioga@fata.unam.mx [Departamento de Nanotecnologia, Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, Blv. Juriquilla 3001, Juriquilla, Queretaro, C.P. 76230 (Mexico)

2011-09-01

ZnO and ZnMnO thin films were obtained by the successive ionic layer adsorption and reaction (SILAR) method. All thin films were deposited on glass microscope slide. A precursor solution of 0.1 M of ZnCl{sub 2} complexed with ammonium hydroxide and water close to boiling point (92 deg. C) as a second solution was used for the ZnO films. An uncomplexed bath comprised of 0.1 M ZnCl{sub 2}, 0.1 M MnCl{sub 2,} and a second solution of 0.1 ml of NH{sub 4}OH with water close to boiling point was used for the ZnMnO films. The film samples were deposited by the SILAR method and annealed at 200 deg. C for 15 min. These samples were characterized using X-Ray Diffraction (XRD), Scanning Electron Microscopy with Energy Dispersive Spectroscopy (EDS), and Atomic Force Microscope. Atomic absorption was used to determine quantitatively the amount of Mn incorporated into the films. According to the XRD patterns these films were polycrystalline with wurtzite hexagonal structure. The morphology of the ZnO films constituted by rice-like and flower-like structures changed significantly to nanosheet structures with the Mn incorporation. The Mn inclusion in a ZnO structure was less than 4% according to the results from EDS, XRD, and atomic absorption.

Characterization of nanostructures of ZnO and ZnMnO films deposited by successive ionic layer adsorption and reaction method

International Nuclear Information System (INIS)

Jimenez-Garcia, F.N.; Espinosa-Arbelaez, D.G.; Vargas-Hernandez, C.; Real, A. del; Rodriguez-Garcia, M.E.

2011-01-01

ZnO and ZnMnO thin films were obtained by the successive ionic layer adsorption and reaction (SILAR) method. All thin films were deposited on glass microscope slide. A precursor solution of 0.1 M of ZnCl 2 complexed with ammonium hydroxide and water close to boiling point (92 deg. C) as a second solution was used for the ZnO films. An uncomplexed bath comprised of 0.1 M ZnCl 2 , 0.1 M MnCl 2, and a second solution of 0.1 ml of NH 4 OH with water close to boiling point was used for the ZnMnO films. The film samples were deposited by the SILAR method and annealed at 200 deg. C for 15 min. These samples were characterized using X-Ray Diffraction (XRD), Scanning Electron Microscopy with Energy Dispersive Spectroscopy (EDS), and Atomic Force Microscope. Atomic absorption was used to determine quantitatively the amount of Mn incorporated into the films. According to the XRD patterns these films were polycrystalline with wurtzite hexagonal structure. The morphology of the ZnO films constituted by rice-like and flower-like structures changed significantly to nanosheet structures with the Mn incorporation. The Mn inclusion in a ZnO structure was less than 4% according to the results from EDS, XRD, and atomic absorption.

Mechanical responses of Zn{sub 1-x}Mn{sub x}O epitaxial thin films

Energy Technology Data Exchange (ETDEWEB)

Chang, Teng-Ruey [Department of Industrial Engineering and Management, Nan Kai University of Techonology, Nantou 54243, Taiwan (China); Tsai, Chien-Huang, E-mail: chtsai12@gmail.com [Department of Automation Engineering, Nan Kai University of Techonology, Nantou 54243, Taiwan (China)

2011-10-15

In this study, we used nanoindentation to investigate the effect of the doping of Mn into ZnO buffer layers on the epitaxial growth of ZnO through plasma-assisted molecular beam epitaxy on c-plane sapphire substrates. We characterized the variation of the mechanical properties of Zn{sub 1-x}Mn{sub x}O alloys as a function of the Mn content in the range (x) from 0 to 0.16, as well as analyzing their microstructures using high-resolution transmission electron microscopy. The presence of the Mn-doped ZnO buffer layer enhanced the nanomechanical properties of the ZnO epilayers significantly. From their Berkovich indenter responses, plots of the Young's modulus (E) and hardness (H) of these films revealed that the value of E increased relatively steadily upon increasing the Mn composition, whereas the value of H reached its maximum when x was equal to 0.16. This discrepancy suggests that Zn{sub 1-x}Mn{sub x}O epilayers of higher Mn contents had higher shear resistances.

Optical and structural properties of Mn-doped ZnO nanorods grown by aqueous chemical growth for spintronic applications

Energy Technology Data Exchange (ETDEWEB)

Strelchuk, V.V. [V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine, 45 Nauky pr., 03028 Kyiv (Ukraine); Nikolenko, A.S., E-mail: nikolenko_mail@ukr.net [V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine, 45 Nauky pr., 03028 Kyiv (Ukraine); Kolomys, O.F.; Rarata, S.V.; Avramenko, K.A.; Lytvyn, P.M. [V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine, 45 Nauky pr., 03028 Kyiv (Ukraine); Tronc, P. [Centre National de la Recherche Scientifique, Ecole Superieure de Physique et de Chimie Industrielles de la Ville de Paris, 10 rue Vauquelin, 75005 Paris (France); Chey, Chan Oeurn; Nur, Omer; Willander, Magnus [Department of Science and Technology, Linköping University, 601 74 Norrköping (Sweden)

2016-02-29

The effect of Mn-doping on the structural, morphological, optical and magnetic properties of the ZnO:Mn nanorods (NRs) synthesized by aqueous chemical process is reported. Grown ZnO:Mn NRs are shown to have hexagonal end facets and the diameters increasing with nominal Mn content. Optical absorption measurements show a decrease in optical band gap with increase of Mn concentration. Raman spectroscopy revealed significant modification of the lattice vibrational properties of the ZnO matrix upon Mn doping. The additional Mn-related vibrational mode, intensity of which increases with amount of Mn can be regarded as an evidence of Mn incorporation into the host lattice of the ZnO. At high Mn concentrations, coexistence of hexagonal Zn{sub 1−x}Mn{sub x}O phase along with the secondary phases of ZnMn{sub 2}O{sub 4} cubic spinel is revealed. Magnetic properties of ZnO:Mn NRs are studied by combinatorial atomic force microscopy and magnetic force microscopy imaging, and obtained clear magnetic contrast at room temperature provides a strong evidence of ferromagnetic behavior. - Highlights: • Synthesis of Mn-doped ZnO nanorods by hydrothermal method is demonstrated. • Doping with Mn significantly changes the morphology of ZnO nanorods. • Additional Mn-induced Raman modes evidence incorporation of Mn into ZnO matrix. • Formation of secondary ZnMn{sub 2}O{sub 4} spinel phase is found at high Mn concentrations. • Contrast MFM images of ZnO:Mn nanorods indicate ferromagnetism at room temperature.

Electrodeposition and Characterization of Mn-Cu-Zn Alloys for Corrosion Protection Coating

Science.gov (United States)

Tsurtsumia, Gigla; Gogoli, David; Koiava, Nana; Kakhniashvili, Izolda; Jokhadze, Nunu; Lezhava, Tinatin; Nioradze, Nikoloz; Tatishvili, Dimitri

2017-12-01

Mn-Cu-Zn alloys were electrodeposited from sulphate bath, containing citrate or EDTA and their mixtures as complexing ligands. The influence of bath composition and deposition parameters on alloys composition, cathodic current efficiency and structural and electrochemical properties were studied. At a higher current density (≥ 37.5 A dm-2) a uniform surface deposit of Mn-Cu-Zn was obtained. Optimal pH of electrolyte (0.3 mol/dm3Mn2+ + 0.6 mol/dm3 (NH4)2SO4 +0.1 mol/dm3Zn2++0.005 mol/dm3 Cu2++ 0.05mol/dm3Na3Cit + 0.15mol/dm3 EDTA; t=300C; τ=20 min) for silvery, nonporous coating of Mn-Cu-Zn alloy was within 6.5-7.5; coating composition: 71-83% Mn, 6-7.8% Cu, 11.5-20% Zn, current efficiency up to 40%. XRD patterns revealed BCT (body centred tetragonal) γ-Mn solid phase solution (lattice constants a=2.68 Å c=3.59 Å). Corrosion measurements of deposited alloys were performed in aerated 3.5% NaCl solution. The corrosion current density (icorr) of the electrodeposited alloys on carbon steel was 10 times lower than corrosion rate of pure zinc and manganese coatings. Triple alloy coatings corrosion potential (Ecorr = -1140 mV vs. Ag/AgCl) preserved negative potential value longer (more than three months) compared to carbon steel substrate (Ecorr = -670 mV vs. Ag/AgCl). Tafel polarization curves taken on Mn-Cu-Zn alloy coating in aerated 3.5% NaCl solution did not show a typical passivation behaviour which can be explained by formation oflow solubility of adherent corrosion products on the alloy surface. Corrosion test of Mn-Cu-Zn electrocoating in chlorine environment shows that it is the best cathodic protective coating for a steel product.

Genesis of the Bangbule Pb-Zn-Cu polymetallic deposit in Tibet, western China: Evidence from zircon U-Pb geochronology and S-Pb isotopes

Science.gov (United States)

Kan, Tian; Zheng, Youye; Gao, Shunbao

2016-04-01

The Banbule Pb-Zn-Cu skarn deposit is located in the Longger-Gongbujiangda volcanic magma arc in the Gangdese-Nyainqentanglha Plate. It is the only lead-zinc polymetallic deposit discovered in the westernmost Nyainqentanglha metallogenic belt. The measured and indicated resources include 0.9 Mt of Pb+Zn (4.77% Pb and 4.74% Zn, respectively), 6499 t of Cu, and 178 t of Ag (18.75g/t Ag). The orebodies mainly occur as lenses, veins and irregular shapes in the contact zone between the quartz-porphyry and limestone of the Upper Permian Xiala Formation, or in the boundaries between limestone and sandstone. Pb-Zn-Cu mineralization in the Banbule deposit is closely associated with skarns. The ore minerals are dominated by galena, sphalerite, chalcopyrite, bornite, and magnetite, with subordinate pyrite, malachite, and azurite. The gangue minerals are mainly garnet, actinolite, diopside, quartz, and calcite. The ore-related quartz-porphyry displays LA-ICP-MS zircon U-Pb age of 77.31±0.74 Ma. The δ34S values of sulfides define a narrow range of -0.8 to 4.7‰ indicating a magmatic source for the ore-forming materials. Lead isotopic systematics yield 206Pb/204Pb of 18.698 to 18.752, 207Pb/204Pb of 15.696 to 15.760, and 208Pb/204Pb of 39.097 to 39.320. The data points are constrained around the growth curves of upper crust and orogenic belt according to the tectonic discrimination diagrams. The calculated Δβ - Δγ values plot within the magmatic field according to the discrimination diagram of Zhu et al. (1995). The S-Pb isotopic data suggest that Bangbule is a typical skarn deposit, and the Pb-Zn-Cu mineralization is genetically related to the quartz-porphyry in the mining district. The discovery of the Bangbule deposit indicates that there is metallogenic potential in the westernmost Nyainqentanglha belt, which is of great importance for the exploration work in this area.

EPR and FTIR spectroscopic studies of MO-Al2O3-Bi2O3-B2O3-MnO2(M = Pb, Zn and Cd) glasses

Science.gov (United States)

Lalitha Phani, A. V.; Sekhar, K. Chandra; Chakradhar, R. P. S.; Narasimha Chary, M.; Shareefuddin, Md

2018-03-01

Glasses of the system (30-x)MO-xAl2O3-15Bi2O3-54.5B2O3-0.5MnO2 [M = Pb, Zn & Cd] (x = 0, 5, 10 & 15 mol%) were prepared by the normal melt quenching method. The amorphous nature of the prepared glasses was confirmed by the XRD studies. The EPR and FTIR studies were carried out at room temperature (RT). The EPR spectra exhibited three resonance signals at g ≈ 2.0 with a hyperfine structure, an absorption around g = 4.3 and a distinct shoulder at g = 3.3. Deconvoluted spectra were drawn for g ≈ 2.0 to resolve the six hyperfine lines. The electron paramagnetic resonance signal at g ≈ 2.0 indicates that the Mn2+ ions are in nearly perfectly octahedral symmetry. The low field signals at g = 3.3 and g = 4.3 are attributed to the Mn2+ ion which are in distorted rhombic symmetries. The hyperfine (HF) splitting constant (A) values suggested that the bonding between Mn2+ ions and its ligands is ionic in nature. The presence of BO3 and BO4 borate units, metal oxide cation units, Mn2+ and Bi-O bond vibrations in BiO3 units were noticed from the FTIR spectra.

Synthesis of Mn doped ZnO nanoparticles with biocompatible capping

International Nuclear Information System (INIS)

Sharda; Jayanthi, K.; Chawla, Santa

2010-01-01

Free standing nanoparticles of ZnO doped with transition metal ion Mn have been prepared by solid state reaction method at 500 deg. C. X-ray diffraction (XRD) analysis confirmed high quality monophasic wurtzite hexagonal structure with particle size of 50 nm and no signature of dopant as separate phase. Incorporation of Mn has been confirmed with EDS. Bio-inorganic interface was created by capping the nanoparticles with heteromultifunctional organic stabilizer mercaptosuccinic acid (MSA). The surface morphological studies by scanning electron microscopy (SEM) showed formation of spherical particles and the nanoballs grow in size uniformly with MSA capping. MSA capping has been confirmed with thermo gravimetric analysis (TGA) and FTIR. Photoluminescence (PL) studies show that the ZnO:Mn 2+ particles are excitable by blue light and emits in orange and red. Occurrence of room temperature ferromagnetism in Mn doped ZnO makes such biocompatible luminescent magnetic nanoparticles very promising material.

Synthesis and characterization of single-phase Mn-doped ZnO

Energy Technology Data Exchange (ETDEWEB)

Chattopadhyay, S.; Dutta, S.; Banerjee, A.; Jana, D. [Department of Physics, University of Calcutta, 92 Acharya Prafulla Chandra Road, Kolkata 700 009, West Bengal (India); Bandyopadhyay, S., E-mail: sbaphy@caluniv.ac.i [Department of Physics, University of Calcutta, 92 Acharya Prafulla Chandra Road, Kolkata 700 009, West Bengal (India); Chattopadhyay, S. [Department of Physics, Taki Government College, Taki 743 429, West Bengal (India); Sarkar, A. [Department of Physics, Bangabasi Morning College, 19 Rajkumar Chakraborty Sarani, Kolkata 700 009, West Bengal (India)

2009-05-01

Different samples of Zn{sub 1-x}Mn{sub x}O series have been prepared using conventional solid-state sintering method. We identified up to what extent doping will enable us to synthesize single-phase polycrystalline Mn-doped ZnO sample, which is one of the prerequisites for dilute magnetic semiconductor, and we have analyzed its some other physical aspects. In synthesizing the samples, proportion of Mn varies from 1 to 5 at%. However, the milling time varied (6, 12, 24, 48 and 96 h) only for 2 at% Mn-doped samples while for other samples (1, 3, 4 and 5 at% Mn doped) the milling time has been fixed to 96 h. Room-temperature X-ray diffraction (XRD) data reveal that all of the prepared samples up to 3 at% of Mn doping exhibit wurtzite-type structure, and no segregation of Mn and/or its oxides has been found. The 4 at% Mn-doped samples show a weak peak of ZnMn{sub 2}O{sub 4} apart from the other usual peaks of ZnO and the intensity of this impurity peak has been further increased for 5 at% of Mn doping. So beyond 3 at% doping, single-phase behavior is destroyed. Band gap for all the 2 at% Mn-doped samples has been estimated to be between 3.21 and 3.19 eV and the reason for this low band gap values has been explained through the grain boundary trapping model. The room-temperature resistivity measurement shows an increase of resistivity up to 48 h of milling and with further milling it saturates. The defect state of these samples has been investigated using the positron annihilation lifetime (PAL) spectroscopy technique. Here all the relevant lifetime parameters of positron i.e. free annihilation (tau{sub 1}) at defect site (tau{sub 2}) and average (tau{sub av}) increases with milling time.

Distribution of As, Cd, Pb, and Zn in redox features of mine-waste impacted wetland soils

Energy Technology Data Exchange (ETDEWEB)

Strawn, Daniel G.; Hickey, Patrick J.; McDaniel, Paul A.; Baker, Leslie L. [Idaho Univ., Moscow (United States). Soil and Land Resources Div.

2012-08-15

Purpose: Wetland soils of the Coeur d'Alene (CdA) River Basin of northern Idaho, USA are contaminated with toxic elements released during mining activities. In this paper, we report results from a multi-scale investigation of total As, Cd, Pb, and Zn distributions along a transect of these contaminated soils. Materials and methods: Four sites along an 80-m transect were established at the Black Rock Slough wetland in CdA River Basin. The elevation difference between the upslope and lowland site was 1.1 m. Soils were sampled from three depths, down to 45 cm. Redoximorphic features were isolated from the soils and categorized into five types of cemented particles, and Fe-enriched and depleted soil masses. Soils and isolated soil separates were analyzed for total elemental concentration. Results and discussion: Within soil profiles, contaminants are enriched in surface horizons as compared to the original depositional profiles. Enrichment was more dramatic in the upland sites than the lowland sites. Fe-enriched masses that ranged in size from a few millimeters to several centimeters were also enriched in As, Pb, and Zn. At the smallest scale investigated, five different soil aggregate types ranging in size from 1 to 2 mm in diameter had distinct contaminant associations: Fe-cemented aggregates were elevated in As and Zn; Mn-cemented aggregates had more than five times as much Pb as the bulk soil; root channels were elevated in As; and charcoal particles were elevated in all contaminants, particularly Pb and Cd. Conclusions: Results show that in wetland soils pedogenic processes differentially distribute contaminants amongst the redoximorphic features. The distribution is affected by landscape position and water table influence. At the pedon scale, there is an enrichment of As, Cd, Pb, and Zn in surface horizons, suggesting that upward flux of contaminants is occurring. This contaminant redistribution should be considered in design of management and remediation

Metallic ions catalysis for improving bioleaching yield of Zn and Mn from spent Zn-Mn batteries at high pulp density of 10.

Science.gov (United States)

Niu, Zhirui; Huang, Qifei; Wang, Jia; Yang, Yiran; Xin, Baoping; Chen, Shi

2015-11-15

Bioleaching of spent batteries was often conducted at pulp density of 1.0% or lower. In this work, metallic ions catalytic bioleaching was used for release Zn and Mn from spent ZMBs at 10% of pulp density. The results showed only Cu(2+) improved mobilization of Zn and Mn from the spent batteries among tested four metallic ions. When Cu(2+) content increased from 0 to 0.8 g/L, the maximum release efficiency elevated from 47.7% to 62.5% for Zn and from 30.9% to 62.4% for Mn, respectively. The Cu(2+) catalysis boosted bioleaching of resistant hetaerolite through forming a possible intermediate CuMn2O4 which was subject to be attacked by Fe(3+) based on a cycle of Fe(3+)/Fe(2+). However, poor growth of cells, formation of KFe3(SO4)2(OH)6 and its possible blockage between cells and energy matters destroyed the cycle of Fe(3+)/Fe(2+), stopping bioleaching of hetaerolite. The chemical reaction controlled model fitted best for describing Cu(2+) catalytic bioleaching of spent ZMBs. Copyright © 2015 Elsevier B.V. All rights reserved.

Complex impedance spectra of chip inductor using Li-Zn-Cu-Mn ferrite

International Nuclear Information System (INIS)

Nakamura, Tatsuya; Naoe, Masayuki; Yamada, Yoshihiro

2006-01-01

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li-Zn-Cu-Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni-Zn-Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li-Zn-Cu-Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li-Zn-Cu-Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li-Zn-Cu-Mn ferrite enabled us to easily design the complex impedance of MCI component

Raman spectroscopy of ZnMnO thin films grown by pulsed laser deposition

Science.gov (United States)

Orozco, S.; Riascos, H.; Duque, S.

2016-02-01

ZnMnO thin films were grown by Pulsed Laser Deposition (PLD) technique onto Silicon (100) substrates at different growth conditions. Thin films were deposited varying Mn concentration, substrate temperature and oxygen pressure. ZnMnO samples were analysed by using Raman Spectroscopy that shows a red shift for all vibration modes. Raman spectra revealed that nanostructure of thin films was the same of ZnO bulk, wurzite hexagonal structure. The structural disorder was manifested in the line width and shape variations of E2(high) and E2(low) modes located in 99 and 434cm-1 respectively, which may be due to the incorporation of Mn ions inside the ZnO crystal lattice. Around 570cm-1 was found a peak associated to E1(LO) vibration mode of ZnO. 272cm-1 suggest intrinsic host lattice defects. Additional mode centred at about 520cm-1 can be overlap of Si and Mn modes.

Competition of the self-activated and Mn-related luminescence in ZnS single crystals

Science.gov (United States)

Bacherikov, Yu. Yu.; Vorona, I. P.; Markevich, I. V.; Korsunska, N. O.; Kurichka, R. V.

2018-06-01

The photoluminescence (PL) and photoluminescence excitation (PLE) spectra of ZnS single crystals thermally doped from ZnS/MnS mixture were studied at 300 and 77 K. PL spectra exhibit bands caused by Mn-related centers and centers of self-activated (SA) emission. Besides intrinsic maximum, a number of narrow peaks corresponded to Mn-related absorption are found in the PLE spectra of both SA and Mn-related emission. A redistribution of SA and Mn-related emission intensities is observed with temperature change. The mechanism of this phenomenon involving free hole trapping by MnZn and the possible position of a ground energy level of substitutional Mn are discussed.

The first report of Pb and Zn accumulation in some native plants from the Peruvian Andes

Science.gov (United States)

Bech, Jaume; Duran, Paola; Poma, Wilfredo; Sánchez, Isidoro; Barceló, Juan; Roca, Núria; Boluda, Rafael; Roca-Pérez, Luís.; Poschenrieder, Charlotte

2010-05-01

Until recent decades little has been known about the remediation of mining sites using metalophytes in Latin America. Metal mining has helped to create severe and diverse environmental problems. The present study proposed to identify and characterize spontaneously growing heavy metal tolerant plant species in the area around the polimetalic mine in Hualgayoc (Cajamarca, Peru). These species are potentially useful for phytorremediation. Plant and soils from their rhizosphere were sampled and analized for concentration of As, Fe, Mn, Pb and Zn. Translocation Factor (TF) defined the metals concentrations ratio between shoots and root biomass and Shoot Accumulation Factor (SAF) the metal concentration ratio between shoot and soil concentration were determined and used to measure the effectiveness of a plant in concentrating metals into its biomass. The soils were neutral pH (7,4±0,5) with variable content of organic carbon (2,4±1,1) and loam texture: sand (42,9±10,8) and clay (16,7±4,6). According to the total metals, all samples exceeded toxicity thresholds, high Pb (20016 ± 32559 mg•kg-1) and Zn (22512 ± 13056 mg•kg-1) concentrations were detected. High shoot Pb and Zn concentrations were found in Plantaginaceae Plantago orbignyana (6998 and 9617 μg/g); Brassicaceae Lepidium bipinnatifidum (6886 and 5034 mg•kg-1) and Asteraceae Senecio sp (4253 and 3870 mg•kg-1) and Baccharis latifolia (2554 and 1284 mg•kg-1 respectively). The high values of TFs indicates that the plants effectively traslocated metales. Lepidium bipinnatifidum shows the highest TFs values (143 in Pb and 21,5 in Zn). The SAF values were much lower than those reported for other species such as Paspalum sp in the Peruvian copper mine, which may be due to a high top soil Pb and Zn concentrations. These species can surely be considered as interesting for phytoextraction, due not only to its accumulative capacity but also since they showed an elevated transfer factor and grew in the

Effects of Mn addition on the microstructure and indentation creep behavior of the hot dip Zn coating

International Nuclear Information System (INIS)

Wang, Youbin; Zeng, Jianmin

2015-01-01

Highlights: • Mn addition could significantly refine the grain of the Zn coating. • Twins could be observed in the Zn coatings. • The stress exponent of the Zn coating increases with Mn addition. • The creep process of the Zn coating is dominated by dislocation climb and twins. - Abstract: The Zn coatings with different Mn additions were prepared by hot dip process, and the effects of the Mn addition on the microstructure and indentation creep behavior of the coatings were investigated through scanning electron microscope and constant-load holding indentation technique at the room temperature. Some twins can be observed in the microstructure of Zn coating, which may account for the formation of the large thermal misfit stress between the zinc coating and the steel substrate. The amount of twin microstructure in the Zn coating decreases with the Mn addition. It is also found that Mn addition could induce MnZn 13 phases to precipitate along the grain boundary and significantly refine the grains of Zn coatings. The steady-state stress of the Zn coating could be improved by Mn addition. The creep stress exponent values are in the range of 14–46 and increases with Mn addition. The creep process of the Zn coating is dominated by dislocation climb and twin formation

Synthesis and property of spinel porous ZnMn2O4 microspheres

Science.gov (United States)

Guo, N.; Wei, X. Q.; Deng, X. L.; Xu, X. J.

2015-11-01

Mesoporous ternary zinc manganese oxides on the Ti sheet substrate are prepared by easy and fast hydrothermal method for the first time. The obtained ZnMn2O4 materials with homogenously distributed pores have been characterized by XRD, SEM and Raman spectra, which show the good crystal phase and particles for improving supercapacitive performance. XRD and SEM images show that the as-prepared samples have good crystallinity, and ZnMn2O4 microsphere has an average diameter of 10 μm. In addition, ZnMn2O4 are also characterized in 2 M KOH solution using three-electrode system. In the work, we study that different substrates (Ti, carbon and nickel foam) have an important effect on the electrochemical performance of the samples. The research of cyclic voltammogram (CV) indicates that the obtained specific capacitance (155 F g-1) values on nickel foam substrate for the ZnMn2O4 microspheres are higher than the values reported for some inexpensive oxides. However, the specific capacitance of all ZnMn2O4 samples has almost no change at two different scan rates which shows good long-term cycling stability. The electrochemical impedance spectroscopy with a small resistance reveals that the as-synthesized samples have good frequency response characteristics. These results indicate that the unique ZnMn2O4 electrode would be a promising electrode for high-performance supercapacitor applications.

Structural, optical and magnetic properties of Mn doped ZnO thin films prepared by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Aravind, Arun, E-mail: aruncusat@gmail.com [Nanophotonic and Optoelectronic Devices Laboratory, Department of Physics, Cochin University of Science and Technology, Kochi 682 022, Kerala (India); Jayaraj, M.K., E-mail: mkj@cusat.ac.in [Nanophotonic and Optoelectronic Devices Laboratory, Department of Physics, Cochin University of Science and Technology, Kochi 682 022, Kerala (India); Kumar, Mukesh; Chandra, Ramesh [Nano Science Laboratory, Institute Instrumentation Centre, IIT Roorkee, Roorkee 247 667, Uttarakhand (India)

2012-08-01

Highlights: Black-Right-Pointing-Pointer Defect induced Raman active modes in Mn doped ZnO thin films. Black-Right-Pointing-Pointer Room temperature ferromagnetism. Black-Right-Pointing-Pointer Morphological variations of ZnO thin films with Mn doping. Black-Right-Pointing-Pointer Variation of refractive index of ZnO thin films with Mn doping. - Abstract: Zn{sub 1-x}Mn{sub x}O thin films were grown by pulsed laser deposition. The phase purity and the structure were confirmed by X-ray diffraction studies. The films have a transmittance more than 80% in the visible region. The refractive index of Zn{sub 0.90}Mn{sub 0.10}O films is found to be 1.77 at 550 nm. The presence of non-polar E{sub 2}{sup high} and E{sub 2}{sup low} Raman modes in thin films indicates that 'Mn' doping does not change the wurtzite structure of ZnO. Apart from the normal modes of ZnO the Zn{sub 1-x}Mn{sub x}O ceramic targets show two additional modes at 332 cm{sup -1} (I{sub 1}) and 524 cm{sup -1} (I{sub 2}). The broad Raman peaks (340-600 cm{sup -1}) observed Zn{sub 0.90}Mn{sub 0.10}O thin films can be deconvoluted into five peaks, denoted as P{sub 1}-P{sub 5}. The possible origins of Raman peaks in Zn{sub 1-x}Mn{sub x}O films are the structural disorder and morphological change caused by the Mn dopant. The B{sub 1}{sup low}, {sup 2}B{sub 1}{sup low}, B{sub 1}{sup high} and A{sub 1}{sup LO} modes as well as the surface phonon mode have been observed in heavily Mn-doped ZnO films. Zn{sub 0.98}Mn{sub 0.02}O thin film shows room temperature ferromagnetism. The saturation magnetic moment of the Zn{sub 0.98}Mn{sub 0.02}O thin film is 0.42{mu}{sub B}/Mn atom. The undoped ZnO film prepared under the same condition shows diamagnetic nature. At higher doping concentrations the formation of Mn clusters suppress the room temperature ferromagnetism in Zn{sub 1-x}Mn{sub x}O thin films and shows paramagnetism. XPS confirms the incorporation of Mn{sup 2+} into the ZnO lattice.

Lead, Zn, and Cd in slags, stream sediments, and soils in an abandoned Zn smelting region, southwest of China, and Pb and S isotopes as source tracers

Energy Technology Data Exchange (ETDEWEB)

Yang, Yuangen; Li, Sun; Bi, Xiangyang; Wu, Pan; Liu, Taozhe; Li, Feili; Liu, Congqiang [Chinese Academy of Sciences, Guiyang City (China). Inst. of Geochemistry

2010-12-15

-normalized enrichment factors for Pb, Zn, and Cd were in 40.6-1,066, 11.6-382, and 128-647 in sediments, and in 58.0-1,771, 10.1-450, and 88.6-1,035 in soils. Greater Pb/Cd and Zn/Cd ratios in slags (241 and 386 in median) than in soils (uncultivated (187 and 267 in median) > cultivated) or sediments (106 and 260 in median) were observed, indicating extra atmospheric borne Cd in soils and sediments from smelting dust emission. Pb, Zn, and Cd were mainly associated with Fe/Mn oxides/hydroxides in soils and sediments, with their mobile fractions varying with land use in soils that had a close relation to pH (r = -0.569, p < 0.01). In {sup 206}Pb/{sup 207}Pb{proportional_to} {sup 208}Pb/{sup 206}Pb diagram, plots of soils and sediments constructed a satisfactory linear model (p < 0.01) with wall rock, coal, and ore samples. Four different domains can be identified in the {delta}{sup 34}S-{sup 206}Pb/{sup 207}Pb diagram, in which soils and sediments formed a domain with middle {delta}{sup 34}(-2.79{proportional_to}+10.3 permille) and {sup 206}Pb/{sup 207}Pb ratios (1.1823 {proportional_to} 1.1853). Smelting activities result in great enrichments of Pb, Zn, and Cd in surveyed soils and sediment. Mobile fraction of these metals was controlled by land use type as well as soil pH, which is informative for land use management to prevent toxic substance from potentially menacing human health. Bean cultivation and low pH can result in more Cd of mobile fraction in soils, therefore, alternative cultivation and pH elevation are recommended for the studied region. This would help reduce the remobilization and uptake of Cd from the polluted soils. (orig.)

Superparamagnetic and ferrimagnetic behavior of nanocrystalline ZnO(MnO)

Science.gov (United States)

Kuryliszyn-Kudelska, I.; Dobrowolski, W.; Arciszewska, M.; Romčević, N.; Romčević, M.; Hadžić, B.; Sibera, D.; Narkiewicz, U.

2018-04-01

We have studied the magnetic properties of nanocrystals of ZnO:MnO prepared by traditional wet chemistry method. The detailed structural and morphological characterization was performed. The results of systematic measurements of AC magnetic susceptibility as a function of temperature and frequency as well as DC magnetization are reported. We observed two different types of magnetic behavior depending on the concentration doping. For samples with low nominal content (up to 30 wt% of MnO), superparamagnetic behavior was observed. We attribute the observed superparamagnetism to the presence of nanosized ZnMnO3 phase. For nanocrystals doped above nominal 60 wt% of MnO ferrimagnetism was detected with TC at around 42 K. This magnetic behavior we assign to the presence of nanosized Mn3O4 phase.

Constructing MnO{sub 2}/single crystalline ZnO nanorod hybrids with enhanced photocatalytic and antibacterial activity

Energy Technology Data Exchange (ETDEWEB)

Yu, Weiwei [College of Physics and Electronic Science, Changsha University of Science and Technology, Changsha 410114 (China); Liu, Tiangui, E-mail: tianguiliu@gmail.com [College of Physics and Microelectronics Science, Hunan University, Changsha 410082 (China); Cao, Shiyi; Wang, Chen [College of Physics and Electronic Science, Changsha University of Science and Technology, Changsha 410114 (China); Chen, Chuansheng, E-mail: 1666423158@qq.com [College of Physics and Electronic Science, Changsha University of Science and Technology, Changsha 410114 (China)

2016-07-15

In order to improve the photocatalytic and antibacterial activity of ZnO nanorods, ZnO nanorods decorated with MnO{sub 2} nanoparticles (MnO{sub 2}/ZnO nanorod hybrids) were prepared by using microwave assisted coprecipitation method under the influence of hydrogen peroxide, and the structure, photocatalytic activity and antibacterial property of the products were studied. Experimental results indicated that MnO{sub 2} nanoparticles are decorated on the surface of single crystalline ZnO nanorods. Moreover, the resultant MnO{sub 2}/ZnO nanorod hybrids have been proven to possess good photocatalytic and antibacterial activity, which their degradated efficiency for Rhodamin B (RhB) is twice as the pure ZnO nanorods. Enhancement for photocatalytic and antibacterial activity is mainly attributed to the low band gap energy and excellent electrochemical properties of MnO{sub 2} nanoparticles. - Graphical abstract: The MnO{sub 2}/single crystalline ZnO nanorods hybrids, which MnO{sub 2} nanoparticles are loaded on the surface of ZnO nanorods, were prepared by the step-by-step precipitation method under the assistance of ammonia and hydrogen peroxide. Display Omitted - Highlights: • MnO{sub 2}/ZnO nanorod hybrids were prepared by the step-by-step assembly method. • Single crystalline ZnO nanorods can be decorated by MnO{sub 2} nanoparticles. • MnO{sub 2}/ZnO nanorod hybrids possess good photocatalytic and antibacterial activity. • MnO{sub 2} can improve the photocatalytic activity of ZnO nanorods under visible light.

On the state of Mn in Mn{sub x}Zn{sub 1−x}O nanoparticles and their surface modification with isonipecotic acid

Energy Technology Data Exchange (ETDEWEB)

Jiménez-Hernández, L.; Estévez-Hernández, O. [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología de Avanzada, Unidad Legaria, Ciudad México, México (Mexico); Instituto de Ciencia y Tecnología de Materiales (IMRE), Universidad de La Habana (Cuba); Hernández, M.P. [Instituto de Ciencia y Tecnología de Materiales (IMRE), Universidad de La Habana (Cuba); Universidad Nacional Autónoma de México (UNAM), Centro de Nanociencias y Nanotecnología (CNyN), Ensenada, Baja California, México (Mexico); Díaz, J.A.; Farías, M.F. [Universidad Nacional Autónoma de México (UNAM), Centro de Nanociencias y Nanotecnología (CNyN), Ensenada, Baja California, México (Mexico); Reguera, E., E-mail: edilso.reguera@gmail.com [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología de Avanzada, Unidad Legaria, Ciudad México, México (Mexico)

2017-03-15

Mn-doped ZnO (Mn{sub x}Zn{sub 1−x}O) nanoparticles were synthesized by the co-precipitation method and coated with isonipecotic acid as capping ligand. The structure, composition and morphology of the resulting nanomaterial were investigated by energy disperse X-ray analysis, X-ray diffraction, and transmission electron microscopy data. Such measurements showed that the solid obtained contains 6 at% of Mn and it is formed by a highly crystalline material with 3–5 nm range of crystallite size, and only a small elongation of its cell parameter with respect to undoped ZnO wurtzite unit cell. Information on the state of manganese atom in the Mn{sub x}Zn{sub 1−x}O nanostructures formed was obtained from X-ray photoelectron (XPS) and electron energy loss (EELS) spectroscopies. XPS and EELS spectra are composed of four peaks, corresponding to two species of Mn(II) and signals from Mn(III) and Mn(IV). Such spectral data on the state of Mn in the material studied is consistent with the mapping of Mn distribution observed in recorded transmission electron microscopy images, which reveal presence of clusters of Mn atoms. Only a fraction of doping Mn atoms were found forming a solid solution with the host ZnO structure. The functionalization of the nanoparticles system with Isonipecotic acid shows that this molecule remains anchored to the nanoparticles surface mainly through its N basic site. The availability of free carboxylate groups in the capping molecule was tested by conjugation to type IV horseradish peroxidase. - Graphical abstract: State of Mn atoms in Mn-doped ZnO nanostructures prepared by the precipitation method, their capping with isonipecotic acid and subsequent conjugation to peroxidase. - Highlights: • State of manganese in manganese-doped zinc oxide nanoparticles. • Isonipecotic acid as surface modifier of ZnO nanoparticles. • Peroxidase conjugation to ZnO nanoparticles modified with isonipecotic acid.

EDTA-assisted hydrothermal synthesis, characterization and photoluminescent properties of Mn{sup 2+}-doped ZnS

Energy Technology Data Exchange (ETDEWEB)

Viswanath, R. [Department of Studies and Research in Industrial Chemistry, School of Chemical Sciences, Kuvempu University, Shankaraghatta-577 451 (India); Bhojya Naik, H.S., E-mail: hsb_naik@rediffmail.com [Department of Studies and Research in Industrial Chemistry, School of Chemical Sciences, Kuvempu University, Shankaraghatta-577 451 (India); Yashavanth Kumar, G.S.; Prashanth Kumar, P.N.; Arun Kumar, G. [Department of Studies and Research in Industrial Chemistry, School of Chemical Sciences, Kuvempu University, Shankaraghatta-577 451 (India); Praveen, R. [Department of Technical Education, Automobile Technology Branch HMS Polytechnic (Government Aided), Tumkur-572102 (India)

2014-09-15

In this paper, undoped ZnS and Mn{sup 2+}-doped ZnS nanocrystals were synthesized through a facile EDTA-assisted hydrothermal method. The as-synthesized powder samples were systematically characterized by employing the following characterization technique such as X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), UV–visible optical absorption and photoluminescence (PL) spectroscopy. X-ray diffraction pattern revealed the presence of material in single phase with average crystallite size of about 3 nm and the material remained cubic over the whole Mn solid solution range. Formation of ultrafine, spherical and homogeneous dispersed nanoparticles with size 4 nm was confirmed by HRTEM analysis. Absorption shoulders of the samples were blue-shifted as compared to bulk ZnS (3.6 eV) with decrease in the energy band gap as the Mn concentration increases. The room temperature photoluminescence (PL) spectra of Mn{sup 2+}-doped ZnS nanocrystalline showed extra peaks in yellow–orange and red region in comparison of pure ZnS. Mn induced PL was suggested with the significant enhancement of the PL intensity in ZnS:Mn nanocrystalline due to Mn incorporation. The red shift in the yellow–orange emission peak can be attributed to the change in band structure due to the formation of ZnS:Mn alloy with increase in Mn{sup 2+} concentration. The yellow–orange emission peak corresponds to the {sup 4}T{sub 1}(excited)–{sup 6}A{sub 1}(ground) transition of Mn{sup 2+} ion in Td symmetry in the ZnS host lattice. The emission peak in the red region may be due to Mn{sup 2+} d–d transitions in (Zn Mn)S matrix as some of the nearest neighbors of Mn{sup 2+} are now predominantly S atoms due to their random positioning nature in the nanocrystallite and Mn–Mn interaction at high Mn{sup 2+} concentration. This type of doped semiconductors with multi-band emission can be made bioactive when they are

Nanoparticles of ZnO doped with Mn: structural and morphological characteristics

Energy Technology Data Exchange (ETDEWEB)

Bonifacio, Maria Aparecida Ribeiro; Lira, Helio de Lucena; Gama, Lucianna, E-mail: m_aparecidaribeiro@yahoo.com.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais; Neiva, Laedna Souto [Universidade Federal do Cariri (UFCA), Juazeiro do Norte, CE (Brazil). Unidade Academica de Materiais; Kiminami, Ruth H. G. A. [Universidade Federal de Sao Carlos (USCar), SP (Brazil). Departamento de Engenharia de Materiais

2017-07-15

In this study, the effects of dopant concentrations on the structural and morphological characteristics of Zn{sub 1-x}Mn{sub x} O powders (x= 0.025, 0.05, 0.075, and 0.1 mole) synthesized by the Pechini method has been investigated. The powder was characterized by X-ray diffraction (XRD), Brunauer-Emmet-Teller (BET) specific surface, energy dispersive X-ray (EDX), scanning electron microscopy (SEM) and Spectroscopy with Fourier transform (FTIR). An XRD analysis of the powder showed the formation of ZnO phase with a typical single phase wurtzite structure. The EDX analysis revealed Mn incorporated in the ZnO structure. The particle size calculated by BET ranged from 24 to 63 nm, confirming the nanometric size of the powder particles. The SEM analysis revealed irregular shaped particle agglomerates and the presence of nanosheets. From FTIR it was confirmed the wurtzite structure in ZnO and ZnO nanoparticles doped with Mn. (author)

Boron-doped MnTe semiconductor-sensitized ZnO solar cells

Indian Academy of Sciences (India)

Administrator

The B-doped MnTe semiconductor was grown on ZnO using two stages of the ... nanoparticles (NPs), i.e. MnTe and MnTe2 were observed with a diameter range of approximately ..... Kongkanand A, Tvrdy K, Takechi K, Kuno M and Kamat P.

Some clues about the interphase reaction between ZnO and MnO2 oxides

International Nuclear Information System (INIS)

Rubio-Marcos, F.; Quesada, A.; Garcia, M.A.; Banares, M.A.; Fierro, J.L.G.; Martin-Gonzalez, M.S.; Costa-Kraemer, J.L.; Fernandez, J.F.

2009-01-01

Raman spectroscopy is used to evidence both the nature of the interphase reaction between ZnO and MnO 2 particles and its kinetic evolution. Zn cations migrate from the ZnO grains during oxygen vacancies formation process and diffuse into the MnO 2 particles leading to an interphase region with an intermediate valence Mn +3 -O-Mn +4 . Large amounts of desorbed Zn cations promote the formation of ZnMn 2 O 4 structure, in addition to the intermediate valence state. The system evolves towards complete formation of the spinel phase at higher thermal treatment times. The reactivity of the ZnO plays an important role in the formation of this interphase. Low-reactivity ZnO powder, in which the oxygen vacancies are previously produced, shows a stabilization of the intermediate valence state with very limited formation of the spinel phase. A clear correlation between the amount of the intermediate state interphase and the magnetic properties has been established. - Graphical abstract: Recently new room temperature interphase magnetism has been reported to appear in ZnO-MnO 2 system. Raman spectroscopy is used to evidence both the nature of the interphase reaction and the kinetic. The interphase evolved towards complete formation of the spinel phase. The reactivity of the ZnO plays an important role in the formation of this interphase. Finally, a clear correlation between the amount of the intermediate valence state and the interphase magnetic properties has been established.

Thermoluminescent properties of ZnS:Mn nanocrystalline powders

International Nuclear Information System (INIS)

Ortiz-Hernández, Arturo Agustín; Méndez García, Víctor Hugo; Pérez Arrieta, María Leticia; Ortega Sígala, José Juan

2015-01-01

Thermoluminescent ZnS nanocrystals doped with Mn 2+ ions were synthesized by chemical co-precipitation method. From X-ray diffraction studies it was observed that the synthesized nanoparticles have cubic zinc blende structure with average sizes of about 40–50 nm. Morphology was analyzed by TEM. Photoluminescence studies showed two transitions, one of them close to 396 nm and other close to 598 nm, which is enhanced with increasing dopant concentration, this behavior was also observed in the cathodoluminescence spectrum. The thermoluminescence gamma dose-response has linear behavior over dose range 5–100 mGy, the glow curve structure shows two glow peaks at 436 K and at 518 K that were taken into account to calculate the kinetic parameters using the Computerized Glow Curve Deconvolution procedure. - Highlights: • Nanocrystals in powder of ZnS:Mn were synthesized using the co-precipitation method. • The integrated TL spectra has a linear behavior on the dose range 5–100 mGy of γ-radiation. • The kinetic parameters were obtained by the CGCD procedure. • Results support the possible use of nanocrystalline ZnS:Mn as a new γ-dose nanoTLD

A test of the stability of Cd, Cu, Hg, Pb and Zn profiles over two decades in lake sediments near the Flin Flon Smelter, Manitoba, Canada

Energy Technology Data Exchange (ETDEWEB)

Percival, J.B.; Outridge, P.M., E-mail: outridge@nrcan.gc.ca

2013-06-01

Lake sediments are valuable archives of atmospheric metal deposition, but the stability of some element profiles may possibly be affected by diagenetic changes over time. In this extensive case study, the stability of sedimentary Cd, Cu, Hg, Pb and Zn profiles was assessed in dated sediment cores that were collected in 2004 from four smelter-affected lakes near Flin Flon, Manitoba, which had previously been cored in 1985. Metal profiles determined in 1985 were in most cases clearly reproduced in the corresponding sediment layers in 2004, although small-scale spatial heterogeneity in metal distribution complicated the temporal comparisons. Pre-smelter (i.e. pre-1930) increases in metal profiles were likely the result of long-range atmospheric metal pollution, coupled with particle mixing at the 1930s sediment surface. However, the close agreement between key inflection points in the metal profiles sampled two decades apart suggests that metals in most of the lakes, and Hg and Zn in the most contaminated lake (Meridian), were stable once the sediments were buried below the surface mixed layer. Cadmium, Cu and Pb profiles in Meridian Lake did not agree as well between studies, showing evidence of upward remobilization over time. Profiles of redox-indicator elements (Fe, Mn, Mo and U) suggested that the rate of Mn oxyhydroxide recycling within sediment was more rapid in Meridian Lake, which may have caused the Cd, Cu and Pb redistribution. - Highlights: • Sedimentary Cd, Cu, Hg, Pb and Zn profiles in four lakes were mostly unchanged over 19 years. • In one lake, Cd, Cu and Pb profiles were offset relative to the originals. • The offset could indicate diagenetic upcore dispersal of these metals.

Synthesis and electrochemical properties of ZnMn_2O_4 anode for lithium-ion batteries

International Nuclear Information System (INIS)

Feng, Chuanqi; Wang, Wei; Chen, Xiao; Wang, Shiquan; Guo, Zaiping

2015-01-01

Graphical abstract: ZnMn_2O_4 nanoparticles were prepared through the rheological phase reaction method (R-ZMO) or the mixed solvothermal method(M-ZMO). The particles of M-ZMO were clustered together to form uniform microspheres morphology. The M-ZMO behaved higher reversible capacity and better cycle performance than that of R-ZMO. - Highlights: • ZnMn_2O_4 nanoparticles were prepared through the rheological phase reaction method (R-ZMO) or the mixed solvothermal method (M-ZMO). • The M-ZMO behaved higher reversible capacity and better cycle performance than that of R-ZMO. • The morphology and cell parameters of ZnMn_2O_4 are important effects on its electrochemical properties. • The diffusion coefficient of Li"+ in M-ZMO is beneficial for M-ZMO to be used an anode. - Abstract: The precursors of ZnMn_2O_4 were synthesized by different methods (the rheological phase reaction method or the mixed solvothermal method). The precursors were heat-treated at a suitable temperature to obtain the expected product (ZnMn_2O_4). The synthesized samples were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical properties of the samples were also investigated. The results show that ZnMn_2O_4 was synthesized successfully. The particles of ZnMn_2O_4 were irregular quasi-spheres with sizes of about 50 nm. The ZnMn_2O_4 nanoparticles synthesized through the mixed solvothermal method were clustered together to form microspheres about 1 μm in diameter. The electrochemical testing results showed that the ZnMn_2O_4 synthesized through the mixed solvothermal method featured higher reversible capacity and better cycling performance than the sample synthesized by the rheological phase reaction method. The ZnMn_2O_4 synthesized through the mixed solvothermal method could be a promising anode material for lithium ion battery application.

Emission properties of Mn doped ZnO nanoparticles prepared by mechanochemical processing

Energy Technology Data Exchange (ETDEWEB)

Sabri, Nurul Syahidah; Yahya, Ahmad Kamal [Faculty of Applied Sciences, Universiti Teknologi MARA, Shah Alam, Selangor 40450 (Malaysia); Talari, Mahesh Kumar, E-mail: talari@gmail.com [Faculty of Applied Sciences, Universiti Teknologi MARA, Shah Alam, Selangor 40450 (Malaysia)

2012-07-15

Mechanochemical processing was reported to introduce lot of crystal defects which can significantly influence emission properties. Nevertheless, to the best of our knowledge, there are no reports on effect of mechanochemical processing on emission properties of transition metal ion doped ZnO. In this study, Zn{sub 1-x}Mn{sub x}O nanoparticles with different Mn content (x=0, 0.02, 0.04, 0.06, 0.08, and 0.1) were prepared by mechanochemical processing to study the effect of Mn doping and processing on emission properties. Confirmation of nanoparticles size and nanocrystalline nature of hexagonal wurtzite ZnO structure is carried out using transmission electron microscopy (TEM) and selected area electron diffraction (SAED), respectively. The samples were also characterized using Fluorescence Spectroscope before and after heat-treatment. The emission studies revealed that blue emission intensity is stronger compared to UV and green emission in contrast to the earlier reports, where other synthesis routes were employed for the ZnO nanoparticles' preparation. The blue emission originates from the zinc interstitial (Zn{sub i}) and oxygen interstitial (O{sub i}) defects, which indicate that the mechanochemical route resulted in more interstitial defects compared to oxygen substitution (O{sub Zn}) and oxygen vacancy (V{sub o}) defects which otherwise would give green emission. Mn doping resulted in shifting of near-band-edge (NBE) emission and the reduction in the intensities of NBE, blue and green emissions. The initial red shift at lower Mn content could be due to s-d and p-d exchange interactions as well as band tailing effect where as the blue shift at higher Mn content can be attributed to the Burstein-Moss shift. The reduction in emission intensity could be due to non-radiative recombination processes promoted by Mn ions with increasing Mn content. - Highlights: Black-Right-Pointing-Pointer Zn{sub 1-x}Mn{sub x}O nanoparticles were prepared by mechanochemical

Photoluminescence study of Mn doped ZnS nanoparticles prepared by co-precipitation method

Energy Technology Data Exchange (ETDEWEB)

Deshpande, M. P., E-mail: vishwadeshpande@yahoo.co.in; Patel, Kamakshi, E-mail: kamphysics@gmail.com; Gujarati, Vivek P.; Chaki, S. H. [Department of Physics, Sardar Patel University, VallabhVidyanagr-388120,Anand, Gujarat, India. (India)

2016-05-06

ZnS nanoparticles co-doped with different concentration (5,10,15%) of Mn were synthesized using polyvinylpyrrolidone (PVP) as a capping agent under microwave irradiation. We confirmed doping of Mn in the host ZnS by EDAX whereas powder X-ray diffractogram showed the cubic zinc blende structure of all these samples. TEM images did showed agglomeration of particles and SAED pattern obtained indicated polycrystalline nature. From SAED pattern we calculated lattice parameter of the samples which have close resemblance from that obtained from XRD pattern. The band gap values of pure and doped ZnS nanoparticles were calculated from UV-Visible absorption spectra. ZnS itself is a luminescence material but when we dope it with transition metal ion such as Mn, Co, and Cu they exhibits strong and intense luminescence in the particular region. The photoluminescence spectra of pure ZnS nanoparticles showed an emission at 421 and 485nm which is blue emission which was originated from the defect sites of ZnS itself and also sulfur deficiency and when doped with Mn{sup 2+} an extra peak with high intensity was observed at 530nm which is nearly yellow-orange emission which isrelated to the presence of Mn in the host lattice.

Magnetism in V-/Mn-doped ZnO layers fabricated on sapphire

Energy Technology Data Exchange (ETDEWEB)

Mofor, A.C.; El-Shaer, A.; Schlenker, E.; Bakin, A.; Waag, A. [Technical University Braunschweig, Institute of Semiconductor Technology, Braunschweig (Germany); Reuss, F.; Kling, R.; Schoch, W.; Limmer, W. [University Ulm, Department of Semiconductor Physics, Ulm (Germany); Ahlers, H.; Siegner, U.; Sievers, S.; Albrecht, M. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany); Eisenmenger, J.; Mueller, T.; Ziemann, P. [University Ulm, Department of Solid State Physics, Ulm (Germany); Huebel, A.; Denninger, G. [Universitaet Stuttgart, 2. Physkalisches Institut, Stuttgart (Germany)

2007-07-15

Doping ZnO with transition metals (TM) is an obvious approach to produce diluted magnetic semiconductors for magnetoelectronic and spintronic applications. We have carried out experimental studies on the fabrication and characterisation of Mn-doped ZnO layers and V-doped ZnO layers and nanorods, the results of which are reviewed in this paper. From SQUID measurements, both epitaxial and implanted ZnMnO layers show paramagnetic behaviour. Epitaxial ZnVO layers show ferromagnetic SQUID signals, but the presence of any secondary phases in the ZnVO layers may not be ruled out. We also show that the used Al{sub 2}O{sub 3} substrates produce a ferromagnetic SQUID signal, that complicates the analysis of magnetisation data and hence the confirmation of ferromagnetism only from SQUID results. (orig.)

Magnetic and photocatalytic properties of nanocrystalline ZnMn2 O4

Indian Academy of Sciences (India)

Decomposition of oxalate precursors at low temperature (∼ 450°C) yielded phase pure ZnMn2O4 nanoparticles. The size of the nanoparticles of ZnMn2O4 obtained from reverse micellar method is relatively much smaller (20–30 nm) as compared to those made by the co-precipitation (40–50 nm) method. Magnetic studies ...

Distribution of P, K, Ca, Mg, Cd, Cu, Fe, Mn, Pb and Zn in wood and bark age classes of willows and poplars used for phytoextraction on soils contaminated by risk elements.

Science.gov (United States)

Zárubová, Pavla; Hejcman, Michal; Vondráčková, Stanislava; Mrnka, Libor; Száková, Jiřina; Tlustoš, Pavel

2015-12-01

Fast-growing clones of Salix and Populus have been studied for remediation of soils contaminated by risk elements (RE) using short-rotation coppice plantations. Our aim was to assess biomass yield and distributions of elements in wood and bark of highly productive willow (S1--[Salix schwerinii × Salix viminalis] × S. viminalis, S2--Salix × smithiana clone S-218) and poplar (P1--Populus maximowiczii × Populus nigra, P2--P. nigra) clones with respect to aging. The field experiment was established in April 2008 on moderately Cd-, Pb- and Zn- contaminated soil. Shoots were harvested after four seasons (February 2012) and separated into annual classes of wood and bark. All tested clones grew on contaminated soils, with highest biomass production and lowest mortality exhibited by P1 and S2. Concentrations of elements, with exception of Ca and Pb, decreased with age and were higher in bark than in wood. The Salix clones were characterised by higher removal of Cd, Mn and Zn compared to the Populus clones. Despite generally higher RE content in young shoots, partly due to lower wood/bark ratios and higher RE concentrations in bark, the overall removal of RE was higher in older wood classes due to higher biomass yield. Thus, longer rotations seem to be more effective when phytoextraction strategy is considered. Of the four selected clones, S1 exhibited the best removal of Cd and Zn and is a good candidate for phytoextraction.

Controlled fabrication and tunable photoluminescence properties of Mn2+ doped graphene–ZnO composite

International Nuclear Information System (INIS)

Luan, Xinglong; Zhang, Yihe; Tong, Wangshu; Shang, Jiwu; An, Qi; Huang, Hongwei

2014-01-01

Highlights: • Graphene–ZnO composites were synthesized by a mixed solvothermal method. • ZnO quantum dots are distributed uniformly on the graphene sheets. • A possible hypothesis is raised for the influence of graphene oxide on the nucleation of ZnO. • Mn 2+ doped graphene–ZnO composites were fabricated and the emission spectra can be tuned by doping. - Abstract: Graphene–ZnO composites (G–ZnO) with controlled morphology and photoluminescence property were synthesized by a mixed solvothermal method. Mixed solvent were composed by dimethyl sulfoxide and ethylene glycol. Fourier transform infrared spectroscopy, transmission electron microscopy and photoluminescence spectra were used to characterize G–ZnO. Graphene as a substrate can help the distribution and the dispersity of ZnO, and a possible model of the interaction between graphene oxide and ZnO particles is proposed. At the same time, graphene also reduce the size of ZnO particles to about 5 nm. Furthermore, Mn 2+ ions dopes G–ZnO successfully by the mixed solvothermal synthesis and the doping of Mn 2+ makes G–ZnO shift red from 465 nm to 548 nm and 554 nm in the emission spectrum. The changes of the emission spectrum by the adding of Mn 2+ make G–ZnO have tunable photoluminescence spectrum which is desirable for practical applications

Defects induced ferromagnetism in Mn doped ZnO

Energy Technology Data Exchange (ETDEWEB)

Chattopadhyay, S.; Neogi, S.K. [Department of Physics, University of Calcutta, 92A P C Road, Kolkata 700009 (India); Sarkar, A. [Department of Physics, Bangabasi Morning College, Kolkata 700009 (India); Mukadam, M.D.; Yusuf, S.M. [Solid State Physics Division, Bhaba Atomic Research Centre, Mumbai 400085 (India); Banerjee, A. [Department of Physics, University of Calcutta, 92A P C Road, Kolkata 700009 (India); Bandyopadhyay, S., E-mail: sbaphy@caluniv.ac.i [Department of Physics, University of Calcutta, 92A P C Road, Kolkata 700009 (India)

2011-02-15

Single phase Mn doped (2 at%) ZnO samples have been synthesized by the solid-state reaction technique. Before the final sintering at 500 {sup o}C, the mixed powders have been milled for different milling periods (6, 24, 48 and 96 h). The grain sizes of the samples are very close to each other ({approx}32{+-}4 nm). However, the defective state of the samples is different from each other as manifested from the variation of magnetic properties and electrical resistivity with milling time. All the samples have been found to be ferromagnetic with clear hysteresis loops at room temperature. The maximum value for saturation magnetization (0.11 {mu}{sub B}/Mn atom) was achieved for 96 h milled sample. Electrical resistivity has been found to increase with increase in milling time. The most resistive sample bears the largest saturation magnetization. Variation of average positron lifetime with milling time bears a close similarity with that of the saturation magnetization. This indicates the key role played by open volume vacancy defects, presumably zinc vacancies near grain surfaces, in inducing ferromagnetic order in Mn doped ZnO. To attain optimum defect configuration favorable for ferromagnetism in this kind of samples proper choice of milling period and annealing conditions is required. - Research highlights: 2 at% Mn doped ZnO samples are single phase. All the samples exhibit ferromagnetism at room temperature. Correlation between saturation magnetization and positron annihilation lifetime established.

Defects induced ferromagnetism in Mn doped ZnO

International Nuclear Information System (INIS)

Chattopadhyay, S.; Neogi, S.K.; Sarkar, A.; Mukadam, M.D.; Yusuf, S.M.; Banerjee, A.; Bandyopadhyay, S.

2011-01-01

Single phase Mn doped (2 at%) ZnO samples have been synthesized by the solid-state reaction technique. Before the final sintering at 500 o C, the mixed powders have been milled for different milling periods (6, 24, 48 and 96 h). The grain sizes of the samples are very close to each other (∼32±4 nm). However, the defective state of the samples is different from each other as manifested from the variation of magnetic properties and electrical resistivity with milling time. All the samples have been found to be ferromagnetic with clear hysteresis loops at room temperature. The maximum value for saturation magnetization (0.11 μ B /Mn atom) was achieved for 96 h milled sample. Electrical resistivity has been found to increase with increase in milling time. The most resistive sample bears the largest saturation magnetization. Variation of average positron lifetime with milling time bears a close similarity with that of the saturation magnetization. This indicates the key role played by open volume vacancy defects, presumably zinc vacancies near grain surfaces, in inducing ferromagnetic order in Mn doped ZnO. To attain optimum defect configuration favorable for ferromagnetism in this kind of samples proper choice of milling period and annealing conditions is required. - Research highlights: → 2 at% Mn doped ZnO samples are single phase. → All the samples exhibit ferromagnetism at room temperature. → Correlation between saturation magnetization and positron annihilation lifetime established.

Aqueous synthesis of highly luminescent glutathione-capped Mn{sup 2+}-doped ZnS quantum dots

Energy Technology Data Exchange (ETDEWEB)

Kolmykov, Oleksii [Université de Lorraine, Laboratoire Réactions et Génie des Procédés (LRGP), UMR 7274, CNRS, 1 rue Grandville, BP 20451, 54001 Nancy Cedex (France); Coulon, Joël [Université de Lorraine, Laboratoire de Chimie Physique et Microbiologie pour l' Environnement (LCPME), UMR 7564, CNRS, Faculté de Pharmacie, 5 rue Albert Lebrun, 54000 Nancy (France); Lalevée, Jacques [Institut de Science des Matériaux de Mulhouse (IS2M), UMR 7361, CNRS, 15 rue Jean Starcky, 68093 Mulhouse (France); Alem, Halima; Medjahdi, Ghouti [Université de Lorraine, Institut Jean Lamour (IJL), UMR 7198, CNRS, BP 70239, 54506 Vandoeuvre-lès-Nancy Cedex (France); Schneider, Raphaël, E-mail: raphael.schneider@univ-lorraine.fr [Université de Lorraine, Laboratoire Réactions et Génie des Procédés (LRGP), UMR 7274, CNRS, 1 rue Grandville, BP 20451, 54001 Nancy Cedex (France)

2014-11-01

In this paper, an aqueous-based route has been developed to prepare highly luminescent glutathione (GSH)-capped Mn-doped ZnS quantum dots (QDs). The dots obtained have an average diameter of 4.3 nm and exhibit the Mn{sup 2+}-related orange luminescence with very low surface defect density. The highest photoluminescence was observed for a Mn{sup 2+} to Zn{sup 2+} molar ratio of 3%. Consecutive overcoating of the Mn:ZnS@GSH QDs by a ZnS shell was done, and the core/shell structured QDs exhibit a PL quantum yield of 23%. Transmission electron microscopy, X-ray powder diffraction, electron spin resonance, X-ray photoelectron spectroscopy, UV–visible spectroscopy and spectrofluorometry have been used to characterize the crystal structure, the doping status, and the optical properties of the doped-QDs. Our systematic investigation shows that Mn:ZnS/ZnS@GSH QDs are highly promising fluorescent labels in biological applications.

Synthesis of metal-doped Mn-Zn ferrite from the leaching solutions of vanadium slag using hydrothermal method

Science.gov (United States)

Liu, Shiyuan; Wang, Lijun; Chou, Kuochih

2018-03-01

Using vanadium slag as raw material, Metal-doped Mn-Zn ferrites were synthesized by multi-step processes including chlorination of iron and manganese by NH4Cl, selective oxidation of Fe cation, and hydrothermal synthesis. The phase composition and magnetic properties of synthesized metal-doped Mn-Zn ferrite were characterized by X-ray powder diffraction, Raman spectroscopy, transmission electron microscopy (TEM), X-ray photon spectra (XPS) and physical property measurement. It was found that Mn/Zn mole ratio significantly affected the magnetic properties and ZnCl2 content significantly influenced the purity of the phase of ferrite. Synthesized metal-doped Mn-Zn ferrite, exhibiting a larger saturation magnetization (Ms = 60.01 emu/g) and lower coercivity (Hc = 8.9 Oe), was obtained when the hydrothermal temperature was controlled at 200 °C for 12 h with a Mn/Zn mole ratio of 4. The effect of ZnCl2 content, Mn/Zn mole ratio and temperature on magnetic properties of the synthesized metal-doped Mn-Zn ferrite were systemically investigated. This process provided a new insight to utilize resources in the aim of obtaining functional materials.

Fabrication and Raman scattering of a core–shell structure based on Mn doped ZnO and barium titanate

International Nuclear Information System (INIS)

Sima, M.; Baibarac, M.; Vasile, E.; Sima, Ma.; Mihut, L.

2015-01-01

Graphical abstract: - Highlights: • ZnO/Zn_1_−_xMn_xO/BaTiO_3 nanorod array on FTO substrate. • Oxygen vacancies in the ZnO/Zn_1_−_xMn_xO nanostructure. • The interface between the ZnO/Zn_1_−_xMn_xO core and the BaTiO_3 shell without unwanted phases. - Abstract: A combination of chemical and thermal annealing techniques was used to prepare an array of ZnO/Zn_1_−_xMn_xO/BaTiO_3 nanorods. ZnO nanorod arrays were obtained by hydrothermal–electrochemical processes. The precursors for Zn_1_−_xMn_xO and BaTiO_3, prepared by sol–gel technique were deposited by spin coating on the surface of ZnO nanorods. Each deposition stage was accompanied by thermal treatment stages. Scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectroscopy reveal the presence of a film of Zn_1_−_xMn_xO with wurtzite structure on the surface of ZnO nanorods. Transmission electron microscopy images demonstrate that a layer of BaTiO_3 is deposited on the surface of each ZnO/Zn_1_−_xMn_xO core shell nanorod. BaTiO_3 film onto the ZnO/Zn_1_−_xMn_xO core shell nanorods is also evidenced in Raman scattering by broadening of the Raman band situated in the spectral range 500–750 cm"−"1.

One-step fabrication of biocompatible chitosan-coated ZnS and ZnS:Mn2+ quantum dots via a γ-radiation route

Science.gov (United States)

Chang, Shu-Quan; Kang, Bin; Dai, Yao-Dong; Zhang, Hong-Xu; Chen, Da

2011-11-01

Biocompatible chitosan-coated ZnS quantum dots [CS-ZnS QDs] and chitosan-coated ZnS:Mn2+ quantum dots [CS-ZnS:Mn2+ QDs] were successfully fabricated via a convenient one-step γ-radiation route. The as-obtained QDs were around 5 nm in diameter with excellent water-solubility. These QDs emitting strong visible blue or orange light under UV excitation were successfully used as labels for PANC-1 cells. The cell experiments revealed that CS-ZnS and CS-ZnS:Mn2+ QDs showed low cytotoxicity and good biocompatibility, which offered possibilities for further biomedical applications. Moreover, this convenient synthesis strategy could be extended to fabricate other nanoparticles coated with chitosan. PACS: 81.07.Ta; 78.67.Hc; 82.35.Np; 87.85.Rs.

Chemical bath deposited PbS thin films on ZnO nanowires for photovoltaic applications

Energy Technology Data Exchange (ETDEWEB)

Gertman, Ronen [Dept of Chemistry, Ben Gurion University of the Negev, Be' er Sheva 84105 (Israel); Ilse Katz Institute for Nanoscale Science and Technology, Ben Gurion University of the Negev, Be' er Sheva 84105 (Israel); Osherov, Anna; Golan, Yuval [Dept of Materials Engineering, Ben Gurion University of the Negev, Be' er Sheva 84105 (Israel); Ilse Katz Institute for Nanoscale Science and Technology, Ben Gurion University of the Negev, Be' er Sheva 84105 (Israel); Visoly-Fisher, Iris, E-mail: irisvf@bgu.ac.il [Ilse Katz Institute for Nanoscale Science and Technology, Ben Gurion University of the Negev, Be' er Sheva 84105 (Israel); Department of Solar Energy and Environmental Physics, Swiss Institute for Dryland Environmental and Energy Research, Jacob Blaustein Institutes for Desert Research, Ben Gurion University of the Negev, Sede Boqer Campus 84990 (Israel)

2014-01-01

Photovoltaic devices usually exploit mid-range band-gap semiconductors which absorb in the visible range of the solar spectrum. However, much energy is lost in the IR and near-IR range. We combined the advantages of small band-gap, bulk-like PbS deposited by facile, cheap and direct chemical bath deposition (CBD), with the good electronic properties of ZnO and the large surface area of nanowires, towards low cost photovoltaic devices utilizing IR and near-IR light. Surprisingly, CBD of PbS on ZnO, and particularly on ZnO nanowires, was not studied hitherto. Therefore, the mechanism of PbS growth by chemical bath deposition on ZnO nanowires was studied in details. A visible proof is shown for a growth mechanism starting from amorphous Pb(OH){sub 2} layer, that evolved into the ‘ion-by-ion’ growth mechanism. The growth mechanism and the resulting morphology at low temperatures were controlled by the thiourea concentration. The grain size affected the magnitude of the band-gap and was controlled by the deposition temperatures. Deposition above 40 °C resulted in bulk-like PbS with an optical band-gap of 0.4 eV. Methods were demonstrated for achieving complete PbS coverage of the complex ZnO NW architecture, a crucial requirement in optoelectronic devices to prevent shorts. Measurements of photocurrents under white and near-IR (784 nm) illumination showed that despite a 200 meV barrier for electron transfer at the PbS/ZnO interface, extraction of photo-electrons from PbS to the ZnO was feasible. The ability to harvest electrons from a narrow band-gap semiconductor deposited on a large surface-area electrode can advance the field towards high efficiency, low cost IR and near-IR sensors and third generation solar cells. - Highlights: • PbS was deposited on ZnO nanowires using chemical bath deposition. • At 50 °C the growth mechanism starts from an amorphous Pb(OH){sub 2} layer. • At 5 °C the growth mechanism of PbS can be controlled by thiourea concentrations

Optical studies on Zn-doped lead chalcogenide (PbSe){sub 100−x}Zn{sub x} thin films composed of nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Ashraf, Md. Tanweer [Department of Applied Sciences and Humanities, Jamia Millia Islamia (JMI), New Delhi-25 (India); Salah, Numan A. [Center of Nanotechnology, King Abdulaziz University, Jeddah (Saudi Arabia); Rafat, M. [Department of Applied Sciences and Humanities, Jamia Millia Islamia (JMI), New Delhi-25 (India); Zulfequar, M. [Department of Physics, Jamia Millia Islamia, New Delhi-25 (India); Khan, Zishan H., E-mail: zishan_hk@yahoo.co.in [Department of Applied Sciences and Humanities, Jamia Millia Islamia (JMI), New Delhi-25 (India)

2016-08-01

The effect of laser-Irradiation on the optical properties of Zn-doped PbSe thin films composed of nanoparticles has been studied. Scanning electron microscope (SEM) investigations suggest the formation of nanoparticles of average size of 50 nm for all the studied Zn compositions. XRD studies show that the as-prepared thin films are polycrystalline in nature. The formation of nanoparticles of Zn-doped PbSe has been confirmed by indexing the crystal planes as observed in the XRD spectra. The addition of Zn in (PbSe){sub 100−x}Zn{sub x} thin films result in the blue shift in photoluminescence spectra, this blue shift is associated with the narrowing of the band gap. Optical absorption measurements reveal a direct band gap for the present samples, which decreases on increasing the Zn content. The same trend has also been observed for the samples irradiated with laser. Further, the calculated values of Urbach energy are found to increase with the increase in Zn contents for the as-prepared as well as laser-irradiated samples. All the above observations agree well with the results of optical band gap and suggest that the decrease in band gap may be due to increase in band tails, defects and particle size. - Highlights: • Nanoparticles of Zn doped (PbSe){sub 100−x}Zn{sub x} lead chalcogenides have been synthesized. • Effect of laser irradiation on optical properties of (PbSe){sub 100−x}Zn{sub x} has been studied. • A blue shift in PL spectra is obtained on Zn incorporation.

Enhanced electrochemical performance of a ZnO-MnO composite as an anode material for lithium ion batteries.

Science.gov (United States)

Song, Min Seob; Nahm, Sahn; Cho, Won Il; Lee, Chongmok

2015-09-28

A ZnO-MnO composite was synthesized using a simple solvothermal method combined with a high-temperature treatment. To observe the phase change during the heating process, in situ high-temperature XRD analysis was performed under vacuum conditions. The results indicated that ZnMn2O4 transformed into the ZnO-MnO composite phase starting from 500 °C and that this composite structure was retained until 700 °C. The electrochemical performances of the ZnO-MnO composite electrode were evaluated through galvanostatic discharge-charge tests and cyclic voltammetry analysis. Its initial coulombic efficiency was significantly improved to 68.3% compared to that of ZnMn2O4 at 54.7%. Furthermore, the ZnO-MnO composite exhibited improved cycling performance and enhanced rate capability compared with untreated ZnMn2O4. To clarify the discharge-charge mechanism of the ZnO-MnO composite electrode, the structural changes during the charge and discharge processes were also investigated using ex situ XRD and TEM.

Biocompatible ZnS:Mn quantum dots for reactive oxygen generation and detection in aqueous media

International Nuclear Information System (INIS)

Diaz-Diestra, Daysi; Beltran-Huarac, Juan; Bracho-Rincon, Dina P.; González-Feliciano, José A.; González, Carlos I.; Weiner, Brad R.; Morell, Gerardo

2015-01-01

We report here the versatility of Mn-doped ZnS quantum dots (ZnS:Mn QDs) synthesized in aqueous medium for generating reactive oxygen species and for detecting cells. Our experiments provide evidence leading to the elimination of Cd-based cores in CdSe/ZnS systems by substitution of Mn-doped ZnS. Advanced electron microscopy, X-ray diffraction, and optical spectroscopy were applied to elucidate the formation, morphology, and dispersion of the products. We study for the first time the ability of ZnS:Mn QDs to act as immobilizing agents for Tyrosinase (Tyr) enzyme. It was found that ZnS:Mn QDs show no deactivation of Tyr enzyme, which efficiently catalyzed the hydrogen peroxide (H 2 O 2 ) oxidation and its eventual reduction (−0.063 V vs. Ag/AgCl) on the biosensor surface. The biosensor showed a linear response in the range of 12 μmol/L–0.1 mmol/L at low operation potential. Our observations are explained in terms of a catalase-cycled kinetic mechanism based on the binding of H 2 O 2 to the axial position of one of the active copper sites of the oxy-Tyr during the catalase cycle to produce deoxy-Tyr. A singlet oxygen quantum yield of 0.62 in buffer and 0.54 in water was found when ZnS:Mn QDs were employed as a photosensitizer in the presence of a chemical scavenger and a standard dye. These results are consistent with a chemical trapping energy transfer mechanism. Our results also indicate that ZnS:Mn QDs are well tolerated by HeLa Cells reaching cell viabilities as high as 88 % at 300 µg/mL of QDs for 24 h of incubation. The ability of ZnS:Mn QDs as luminescent nanoprobes for bioimaging is also discussed.Graphical Abstract

Biocompatible ZnS:Mn quantum dots for reactive oxygen generation and detection in aqueous media

Science.gov (United States)

Diaz-Diestra, Daysi; Beltran-Huarac, Juan; Bracho-Rincon, Dina P.; González-Feliciano, José A.; González, Carlos I.; Weiner, Brad R.; Morell, Gerardo

2015-12-01

We report here the versatility of Mn-doped ZnS quantum dots (ZnS:Mn QDs) synthesized in aqueous medium for generating reactive oxygen species and for detecting cells. Our experiments provide evidence leading to the elimination of Cd-based cores in CdSe/ZnS systems by substitution of Mn-doped ZnS. Advanced electron microscopy, X-ray diffraction, and optical spectroscopy were applied to elucidate the formation, morphology, and dispersion of the products. We study for the first time the ability of ZnS:Mn QDs to act as immobilizing agents for Tyrosinase (Tyr) enzyme. It was found that ZnS:Mn QDs show no deactivation of Tyr enzyme, which efficiently catalyzed the hydrogen peroxide (H2O2) oxidation and its eventual reduction (-0.063 V vs. Ag/AgCl) on the biosensor surface. The biosensor showed a linear response in the range of 12 μmol/L-0.1 mmol/L at low operation potential. Our observations are explained in terms of a catalase-cycled kinetic mechanism based on the binding of H2O2 to the axial position of one of the active copper sites of the oxy-Tyr during the catalase cycle to produce deoxy-Tyr. A singlet oxygen quantum yield of 0.62 in buffer and 0.54 in water was found when ZnS:Mn QDs were employed as a photosensitizer in the presence of a chemical scavenger and a standard dye. These results are consistent with a chemical trapping energy transfer mechanism. Our results also indicate that ZnS:Mn QDs are well tolerated by HeLa Cells reaching cell viabilities as high as 88 % at 300 µg/mL of QDs for 24 h of incubation. The ability of ZnS:Mn QDs as luminescent nanoprobes for bioimaging is also discussed.

Microstructure and in vitro degradation performance of Mg-Zn-Mn alloys for biomedical application.

Science.gov (United States)

Rosalbino, F; De Negri, S; Scavino, G; Saccone, A

2013-03-01

Manganese and zinc were selected as alloying elements to develop a Mg-based ternary alloy for biomedical applications, taking into account the good biocompatibility of these metals. The microstructures of Mg-Zn-Mn alloys containing 0.5 or 1.0 mass% of manganese and 1.0 or 1.5 mass% of zinc were investigated by scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. Their corrosion properties were assessed by means of potentiodynamic polarization and electrochemical impedance spectroscopy measurements performed in Ringer's physiological solution that simulates bodily fluids. All tested samples are two-phase alloys formed by a Mg-based matrix, consisting of a Mg-Zn-Mn solid solution, and a Mg-Zn binary phase. The electrochemical results show an improvement of the corrosion behavior of the investigated alloys with increasing Zn and Mn content. This is attributed to the formation of a partially protective Mg(OH)(2) surface film whose protective capabilities are increased by the alloying elements. The reduced influence of the Mg-Zn intermetallic compound on the corrosion rate of Mg-Zn-Mn alloys in the presence of a partially protective surface layer can be ascribed to an increasing resistance between the Mg-Zn-Mn solid solution and the second phase, thereby decreasing the effective driving force for microgalvanic corrosion. Owing to its highest corrosion protective ability, the Mg-1.5Zn-1Mn alloy is a promising candidate for the development of degradable implants, such as screws, plates, and rods. Copyright © 2012 Wiley Periodicals, Inc.

Piezoelectric properties and temperature stability of Mn-doped Pb(Mg1/3Nb2/3)-PbZrO3-PbTiO3 textured ceramics

OpenAIRE

Yan, Yongke; Cho, Kyung-Hoon; Priya, Shashank

2012-01-01

In this letter, we report the electromechanical properties of textured 0.4Pb(Mg1/3Nb2/3) O-3-0.25PbZrO(3)-0.35PbTiO(3) (PMN-PZT) composition which has relatively high rhombohedral to tetragonal (R-T) transition temperature (TR-T of 160 degrees C) and Curie temperature (T-C of 234 degrees C) and explore the effect of Mn-doping on this composition. It was found that MnO2-doped textured PMN-PZT ceramics with 5 vol.% BaTiO3 template (T-5BT) exhibited inferior temperature stability. The coupling f...

Effect of small addition of Mn on the passivation of Zn in 0.1 M NaOH solution

International Nuclear Information System (INIS)

Shang Xiuling; Zhang Bo; Han Enhou; Ke Wei

2011-01-01

The passivation of pure Zn (99.995 wt%) and Zn-0.4Mn (0.4 wt% Mn) alloy in a deaerated 0.1 M NaOH solution (pH 12.9) was investigated by electrochemical measurements, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The potentiodynamic polarization and electrochemical impedance measurements show that addition of 0.4 wt% Mn can decrease the passive current density of Zn in the passive region. XPS surface analysis indicates that there is approximately 1.0-2.0 at% Mn 2+ being incorporated into the passive film on Zn-0.4Mn alloy with Mn content being higher in the outer layers. Mott-Schottky analysis shows that the incorporated Mn can decrease concentration of defects in the film. AFM observations disclose that Mn can decrease the grain size of the film. The mechanism by which Mn additions improve the passivity of Zn is that the incorporated Mn can inhibit ions transportation in the film and inhibit its growth. Meanwhile, Mn can also promote the nucleation of Zn oxides and decrease film porosity.

The Survey and Measurement of Ni, Pb, Cu, Mn, Zn, Cd and V Content in Green Vegetables of South Area of Tehran Refinery

International Nuclear Information System (INIS)

Kazemzadeh Khoyi, J.; Noori, A. S.; Pourang, N.; Alizadeh, M.; Ghoreishi, H.; Padash, A.

2013-01-01

Oil pollution is one of the most critical soil and water pollutant. Areas which are subjected to oil industry may have this kind of pollution by different ways such as extraction, transformation and refining. The example of these areas is south east of Tehran refinery which is surrounded by agricultural fields and are subjected by pollution via Tehran refinery, oil transforming lines, waste water and industrial activities. Since the crops from this area is providing the needs of neighbor cities like Tehran, to realize their oil pollution, the content of some heavy metals like Ni, V, Cu, Cd, Zn, Pb and Mn has been measured. The results analyzed by analytical method include SPSS and MVSP. Finally the relation between elements and pollution has been recognized. The result of this survey showed the high heavy metal content in most plants which were higher than similar research. Onion had the highest amount of most heavy metals. Ni and Pd content were high in plants which are indicator of oil pollution.

Highly efficient transparent Zn2SiO4:Mn2+ phosphor film on quartz glass

International Nuclear Information System (INIS)

Seo, K.I.; Park, J.H.; Kim, J.S.; Kim, G.C.; Yoo, J.H.

2009-01-01

Highly efficient transparent Zn 2 SiO 4 :Mn 2+ film phosphors on quartz substrates were deposited by the thermal diffusion of sputtered ZnO:Mn film. They show a textured structure with some preferred orientations. Our film phosphor shows, for the best photoluminescence (PL) brightness, a green PL brightness of about 20% of a commercial Zn 2 SiO 4 :Mn 2+ powder phosphor screen. The film shows a high transmittance of more than 10% at the red-color region. The excellence in PL brightness and transmittance can be explained in terms of the textured crystal growth with a continuous gradient of Zn 2 SiO 4 : Mn 2+ crystals.

Effect of Mn content on structural, optical, opto-thermal and electrical properties of ZnO:Mn sprayed thin films compounds

International Nuclear Information System (INIS)

Mimouni, R.; Kamoun, O.; Yumak, A.; Mhamdi, A.; Boubaker, K.; Petkova, P.; Amlouk, M.

2015-01-01

Highlights: • Proposing an original explanation to the difference between manganese-doped zinc oxide and undoped behavior. • Presenting an original effective electrical and fluorescence-related calculation scheme. • Outlining original AC–DC investigation protocol. - Abstract: Manganese-doped zinc oxide thin films (ZnO:Mn) at different percentages (0–3%) were deposited on glass substrates using a chemical spray technique. The effects of manganese element content on structural, optical, opto-thermal and electrical conductivity of ZnO:Mn thin films were investigated by means of X-ray diffraction, optical measurement, Photoluminescence spectroscopy and impedance spectroscopy. XRD analysis revealed that all films consist of single phase ZnO and were well crystallized in würtzite phase with the crystallites preferentially oriented towards (0 0 2) direction parallel to c-axis. Doping manganese resulted in a slight decrease in the optical band gap energy of the films and a noticeably change in optical constants. The UV peak positions for ZnO:Mn samples slightly red shift to the longer wavelength in comparison with the pure ZnO which can be attributed to the change in the acceptor level induced by the substitutional Mn 2+ and the band-gap narrowing of ZnO with the Mn dopant. We have performed original AC and DC conductivity studies inspired from Jonscher and small polaron models. These studies helped establishing significant correlation between temperature and activation energy and Mn content. From the spectroscopy impedance analysis we investigated the frequency relaxation phenomenon and the circuit equivalent circuit of such thin films. Finally, all results have been discussed, as an objective of the actual work, in terms of the manganese doping concentration

Fabrication and Raman scattering of a core–shell structure based on Mn doped ZnO and barium titanate

Energy Technology Data Exchange (ETDEWEB)

Sima, M., E-mail: msima@infim.ro [National Institute of Materials Physics, 105 bis Atomistilor Street, PO Box MG 7, 077125 Magurele (Romania); Baibarac, M. [National Institute of Materials Physics, 105 bis Atomistilor Street, PO Box MG 7, 077125 Magurele (Romania); Vasile, E. [University “Politehnica” of Bucharest, Faculty of Applied Chemistry and Material Science, Department of Oxide Materials and Nanomaterials, No. 1-7 Gh. Polizu Street, 011061 Bucharest (Romania); Sima, Ma.; Mihut, L. [National Institute of Materials Physics, 105 bis Atomistilor Street, PO Box MG 7, 077125 Magurele (Romania)

2015-11-15

Graphical abstract: - Highlights: • ZnO/Zn{sub 1−x}Mn{sub x}O/BaTiO{sub 3} nanorod array on FTO substrate. • Oxygen vacancies in the ZnO/Zn{sub 1−x}Mn{sub x}O nanostructure. • The interface between the ZnO/Zn{sub 1−x}Mn{sub x}O core and the BaTiO{sub 3} shell without unwanted phases. - Abstract: A combination of chemical and thermal annealing techniques was used to prepare an array of ZnO/Zn{sub 1−x}Mn{sub x}O/BaTiO{sub 3} nanorods. ZnO nanorod arrays were obtained by hydrothermal–electrochemical processes. The precursors for Zn{sub 1−x}Mn{sub x}O and BaTiO{sub 3}, prepared by sol–gel technique were deposited by spin coating on the surface of ZnO nanorods. Each deposition stage was accompanied by thermal treatment stages. Scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectroscopy reveal the presence of a film of Zn{sub 1−x}Mn{sub x}O with wurtzite structure on the surface of ZnO nanorods. Transmission electron microscopy images demonstrate that a layer of BaTiO{sub 3} is deposited on the surface of each ZnO/Zn{sub 1−x}Mn{sub x}O core shell nanorod. BaTiO{sub 3} film onto the ZnO/Zn{sub 1−x}Mn{sub x}O core shell nanorods is also evidenced in Raman scattering by broadening of the Raman band situated in the spectral range 500–750 cm{sup −1}.

Band alignment of type I at (100ZnTe/PbSe interface

Directory of Open Access Journals (Sweden)

Igor Konovalov

2016-06-01

Full Text Available A junction of lattice-matched cubic semiconductors ZnTe and PbSe results in a band alignment of type I so that the narrow band gap of PbSe is completely within the wider band gap of ZnTe. The valence band offset of 0.27 eV was found, representing a minor barrier during injection of holes from PbSe into ZnTe. Simple linear extrapolation of the valence band edge results in a smaller calculated band offset, but a more elaborate square root approximation was used instead, which accounts for parabolic bands. PbSe was electrodeposited at room temperature with and without Cd2+ ions in the electrolyte. Although Cd adsorbs at the surface, the presence of Cd in the electrolyte does not influence the band offset.

Thallium transformation and partitioning during Pb-Zn smelting and environmental implications.

Science.gov (United States)

Liu, Juan; Wang, Jin; Chen, Yongheng; Xie, Xiaofan; Qi, Jianying; Lippold, Holger; Luo, Dinggui; Wang, Chunlin; Su, Longxiao; He, Lucheng; Wu, Qiwei

2016-05-01

Thallium (Tl) is a toxic and non-essential heavy metal. Raw Pb-Zn ores and solid smelting wastes from a large Pb-Zn smelting plant - a typical thallium (Tl) pollution source in South China, were investigated in terms of Tl distribution and fractionation. A modified IRMM (Institute for Reference Materials and Measurement, Europe) sequential extraction scheme was applied on the samples, in order to uncover the geochemical behavior and transformation of Tl during Pb-Zn smelting and to assess the potential environmental risk of Tl arising from this plant. Results showed that the Pb-Zn ore materials were relatively enriched with Tl (15.1-87.7 mg kg(-1)), while even higher accumulation existed in the electrostatic dust (3280-4050 mg kg(-1)) and acidic waste (13,300 mg kg(-1)). A comparison of Tl concentration and fraction distribution in different samples clearly demonstrated the significant role of the ore roasting in Tl transformation and mobilization, probably as a result of alteration/decomposition of related minerals followed by Tl release and subsequent deposition/co-precipitation on fine surface particles of the electrostatic dust and acidic waste. While only 10-30% of total Tl amounts was associated with the exchangeable/acid-extractable fraction of the Pb-Zn ore materials, up to 90% of total Tl was found in this fraction of the electrostatic dust and acidic waste. Taking into account the mobility and bioavailability of this fraction, these waste forms may pose significant environmental risk. Copyright © 2016 Elsevier Ltd. All rights reserved.

Elucidation of the enhanced ferromagnetic origin in Mn-doped ZnO nanocrystals embedded into a SiO₂ matrix

Energy Technology Data Exchange (ETDEWEB)

Lee, Sejoon; Lee, Youngmin; Kim, Deukyoung [Dongguk University, Seoul (Korea, Republic of)

2013-01-01

The origin of the enhanced room temperature ferromagnetism in Mn-doped ZnO (ZnO:Mn) nanocrystals is investigated. ZnO:Mn nanocrystals, which were fabricated by using a laser irradiation method with a 248-nm KrF excimer laser, exhibited two-times increase in the spontaneous magnetization (∼0.4 emu/cm³ at 300 K) compared to the ZnO:Mn thin film (∼0.2 emu/cm³ at 300 K). The increased exchange integral of J₁/k{sub B} = 51.6 K in ZnO:Mn nanocrystals, in comparison with the ZnO:Mn thin film (J₁/k{sub B} = 46.9 K), is indicative of the enhanced ferromagnetic exchange interaction. This is attributed to the large number of acceptor defects in the SiO₂-capped ZnO:Mn nanocrystals. Namely, the holes bound to the acceptor defects form microscopic bound-magnetic-polarons with Mn ions; hence, long-range ferromagnetic coupling is enhanced. The results suggest that ferromagnetism in ZnO-based dilute magnetic semiconductors can be controlled by modulating the density of native point defects, which can be chemically and thermodynamically modified during the material synthesis or preparation.

Single-layer ZnMN2 (M = Si, Ge, Sn) zinc nitrides as promising photocatalysts.

Science.gov (United States)

Bai, Yujie; Luo, Gaixia; Meng, Lijuan; Zhang, Qinfang; Xu, Ning; Zhang, Haiyang; Wu, Xiuqiang; Kong, Fanjie; Wang, Baolin

2018-05-30

Searching for two-dimensional semiconductor materials that are suitable for visible-light photocatalytic water splitting provides a sustainable solution to deal with the future energy crisis and environmental problems. Herein, based on first-principles calculations, single-layer ZnMN2 (M = Si, Ge, Sn) zinc nitrides are proposed as efficient photocatalysts for water splitting. Stability analyses show that the single-layer ZnMN2 zinc nitrides exhibit energetic and dynamical stability. The electronic properties reveal that all of the single-layer ZnMN2 zinc nitrides are semiconductors. Interestingly, single-layer ZnSnN2 is a direct band gap semiconductor with a desirable band gap (1.74 eV), and the optical adsorption spectrum confirms its optical absorption in the visible light region. The hydrogen evolution reaction (HER) calculations show that the catalytic activity for single-layer ZnMN2 (M = Ge, Sn) is better than that of single-layer ZnSiN2. Furthermore, the band gaps and band edge positions for the single-layer ZnMN2 zinc nitrides can be effectively tuned by biaxial strain. Especially, single-layer ZnGeN2 can be effectively tuned to match better with the redox potentials of water and enhance the light absorption in the visible light region at a tensile strain of 5%, which is confirmed by the corresponding optical absorption spectrum. Our results provide guidance for experimental synthesis efforts and future searches for single-layer materials suitable for photocatalytic water splitting.

Convenient synthesis of Mn-doped Zn (O,S) nanoparticle photocatalyst for 4-nitrophenol reduction

Science.gov (United States)

Susanto Gultom, Noto; Abdullah, Hairus; Kuo, Dong-Hau

2018-04-01

The conversion of 4-nitrophenol as a toxic and waste pollutant to 4-aminophenol as a non-toxic and useful compound by photocatalytic reduction is highly important. In this work, the solid-solution concept by doping was involved to synthesis earth-abundant and green material of Mn-doped Zn(O,S). Zn(O,S) with different Mn doping contents was easily synthesized at low temperature 90°C for 4-NP reduction without using the reducing agent of NaBH4. The Mn-doped Zn(O,S) catalyst exhibited the enhancements in optical and electrochemical properties compared to un-doped Zn(O,S).It was found that 10% Mn-doped Zn(O,S) had the best properties and it could totally reduce 4-NP after 2h photoreactions under low UV illumination. The hydrogen ion was proposed to involve the 4-NP reduction to 4-AP, which is hydrogen ion and electron replaced the oxygen in amino (NO2) group of 4-NP to form the nitro (NH2) group. We alsoproposed the incorporation of Mn in Zn site in the Zn(O,S) host lattice could make the oxygen surface bonding weak for easily forming the oxygen vacancy. The more oxygen vacancy for more hydrogen ion would be generated to consume for 4-NP reduction.

First-principles study on electronic and magnetic properties of (Mn,Fe)-codoped ZnO

International Nuclear Information System (INIS)

Cao, Huawei; Lu, Pengfei; Cai, Ningning; Zhang, Xianlong; Yu, Zhongyuan; Gao, Tao; Wang, Shumin

2014-01-01

First-principle calculations have been performed to investigate the electronic and magnetic properties of (Mn,Fe)-codoped ZnO within the generalized gradient approximation (GGA) and GGA+U schemes. The formation energy of five different configurations is investigated and the ground state is demonstrated to be ferromagnetic ordering. By applying the U correction, the band gap energy of pure ZnO is close to the experimental values, while the ferromagnetic ordering of the ground state remains unchanged. The ferromagnetic stabilization is mediated by double exchange mechanism. In addition, defects corresponding to Zn-vacancy and O-vacancy cannot enhance the ferromagnetism obviously. These results indicate that (Mn,Fe)-codoped ZnO are promising magneto-electronic and spintronic materials. - Highlights: • We have considered 5 different configurations of Mn/Fe codoped bulk ZnO. • The formation energy is calculated to investigate the structural stability. • The double exchange mechanism is responsible for the ferromagnetic behavior. • Defects are not effective method to get room temperature ferromagnetism. • Mn/Fe codoped ZnO are promising ferromagnetic semiconductor materials

First-principles study on electronic and magnetic properties of (Mn,Fe)-codoped ZnO

Energy Technology Data Exchange (ETDEWEB)

Cao, Huawei [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, Beijing 100876 (China); Lu, Pengfei, E-mail: photon.bupt@gmail.com [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, Beijing 100876 (China); Cai, Ningning; Zhang, Xianlong; Yu, Zhongyuan [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, Beijing 100876 (China); Gao, Tao [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); Wang, Shumin [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Photonics Laboratory, Department of Microtechnology and Nanoscience, Chalmers University of Technology, 41296 Gothenburg (Sweden)

2014-02-15

First-principle calculations have been performed to investigate the electronic and magnetic properties of (Mn,Fe)-codoped ZnO within the generalized gradient approximation (GGA) and GGA+U schemes. The formation energy of five different configurations is investigated and the ground state is demonstrated to be ferromagnetic ordering. By applying the U correction, the band gap energy of pure ZnO is close to the experimental values, while the ferromagnetic ordering of the ground state remains unchanged. The ferromagnetic stabilization is mediated by double exchange mechanism. In addition, defects corresponding to Zn-vacancy and O-vacancy cannot enhance the ferromagnetism obviously. These results indicate that (Mn,Fe)-codoped ZnO are promising magneto-electronic and spintronic materials. - Highlights: • We have considered 5 different configurations of Mn/Fe codoped bulk ZnO. • The formation energy is calculated to investigate the structural stability. • The double exchange mechanism is responsible for the ferromagnetic behavior. • Defects are not effective method to get room temperature ferromagnetism. • Mn/Fe codoped ZnO are promising ferromagnetic semiconductor materials.

Synthesis, characterization and physicochemical properties of nanosized Zn/Mn oxides system

International Nuclear Information System (INIS)

Selim, M.M.; Deraz, N.M.; Elshafey, O.I.; El-Asmy, A.A.

2010-01-01

A series of pure and doped Li 2 O-zinc/manganese mixed oxides was prepared by ceramic route at 400-1000 o C. The obtained solids have been characterized by the thermo-gravimetric analyzer (TGA), differential scanning calorimetry (DSC), X-ray powder diffractogram (XRD), infrared (IR), transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) techniques. The catalytic behavior of pure and doped mixed solids was investigated using the decomposition reaction of H 2 O 2 at 30-50 o C. The obtained results revealed that the solid state reaction between ZnO and Mn 2 O 3 started at 500 o C yielding zinc manganite (ZnMn 2 O 4 ) nanoparticles. The augmentation in the calcination temperature of the investigated solids up to 1000 o C for 4 h brought about complete conversion of unreacted oxides yielding ZnMn 2 O 4 crystallites. By doping the system with Li 2 O at different calcination temperatures, an enhancement of the formation of zinc manganite was observed. The products obtained by doping with Li 2 O at different temperatures had less catalytic activity than the pure solids. The catalytic activity of pure and Li 2 O-doped Zn/Mn mixed oxides system decreased by increasing the calcination temperature.

Effect of tellurium on machinability and mechanical property of CuAlMnZn shape memory alloy

International Nuclear Information System (INIS)

Liu Na; Li Zhou; Xu Genying; Feng Ze; Gong Shu; Zhu Lilong; Liang Shuquan

2011-01-01

Highlights: → A novel free-machining Cu-7.5Al-9.7Mn-3.4Zn-0.3Te (wt.%) shape memory alloy has been developed. → The size of dispersed particles with richer Te is 2-5 μm. → The CuAlMnZnTe alloy has good machinability which approached that of BZn15-24-1.5 due to the addition of Te. → Its shape memory property keeps the same as that of CuAlMnZn alloy with free Te. → The CuAlMnZn shape memory alloy with and without Te both have good ductile as annealed at 700 deg. C for 15 min. - Abstract: The microstructure transition, shape memory effect, machinability and mechanical property of the CuAlMnZn alloy with and without Te have been studied using X-ray diffraction analysis, chips observation and scanning electron microscopy (SEM), tensile strength test and differential scanning calorimeter (DSC), and semi-quantitative shape memory effect (SME) test. The particles with richer Te dispersedly distributed in grain interior and boundary with size of 2-5 μm. After the addition of Te, the CuAlMnZnTe alloy machinability has been effectively increased to approach that of BZn15-24-1.5 and its shape memory property remains the same as the one of CuAlMnZn alloy. The CuAlMnZn shape memory alloys with and without Te both have good ductility as annealed at 700 deg. C for 15 min.

Synthesis and inkjet printing of aqueous ZnS:Mn nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Angelo, Peter D., E-mail: peter.angelo@mail.utoronto.ca [Department of Chemical Engineering and Applied Chemistry, Pulp and Paper Centre, University of Toronto, 200 College Street, Toronto, Canada M5G3A1 (Canada); Kronfli, Rosanna; Farnood, Ramin R. [Department of Chemical Engineering and Applied Chemistry, Pulp and Paper Centre, University of Toronto, 200 College Street, Toronto, Canada M5G3A1 (Canada)

2013-04-15

Nanoparticles of ZnS doped with Mn, a common photo- and electro-luminescent species, were synthesized in water using a competitive precipitation method. Particle size was controlled by selection of an appropriate stabilizer added during synthesis, 3-mercaptopropionic acid, which also rendered the particles water-dispersible after synthesis and isolation. Primary particle size was ∼3 nm, with small agglomerates of 10–20 nm in size. The particles were stably dispersed into water at a loading of 2.5 w/w%. This dispersion formed the basis for an aqueous inkjet ink, containing 1 w/w% ZnS:Mn. The small particle size allowed the nanoparticles to be successfully delivered to several substrates without loss during filtration or jetting. Bright photoluminescence was observed in the printed patterns on some substrates (glass, photo-paper, foil, etc.) but was quenched on other substrates where the ink penetrated into the surface (uncoated paper). The small drop volume (10 pL) allowed for reasonably high-resolution printed patterns to be deposited, albeit with significant surface roughness due to the “coffee-ring” effect. -- Highlights: ► Highly monodisperse ZnS:Mn nanoparticles were prepared in aqueous solution. ► ZnS:Mn incorporated into a fluid with suitable properties for inkjet printing. ► Photoluminescence was bright on impermeable substrates but quenched on paper. ► Film smoothness was compromised by high solids loading, and high viscosity of ink.

Defect induced activation of Raman silent modes in rf co-sputtered Mn doped ZnO thin films

Energy Technology Data Exchange (ETDEWEB)

Yadav, Harish Kumar [Department of Physics and Astrophysics, University of Delhi, Delhi-110007 (India); Sreenivas, K [Department of Physics and Astrophysics, University of Delhi, Delhi-110007 (India); Katiyar, R S [Department of Physics, University of Puerto Rico, San Juan, PR 00931-3343 (Puerto Rico); Gupta, Vinay [Department of Physics and Astrophysics, University of Delhi, Delhi-110007 (India)

2007-10-07

We study the influence of Mn doping on the vibrational properties of rf sputtered ZnO thin films. Raman spectra of the Mn doped ZnO samples reveal two additional vibrational modes, in addition to the host phonon modes, at 252 and 524 cm{sup -1}. The intensity of the additional modes increases continuously with Mn concentration in ZnO and can be used as an indication of Mn incorporation in ZnO. The modes are assigned to the activation of ZnO silent modes due to relaxation of Raman selection rules produced by the breakdown of the translational symmetry of the crystal lattice with the incorporation of Mn at the Zn site. Furthermore, the A{sub 1} (LO) mode is observed with very high intensity in the Raman spectra of undoped ZnO thin film and is attributed to the built-in electric field at the grain boundaries.

Defect induced activation of Raman silent modes in rf co-sputtered Mn doped ZnO thin films

International Nuclear Information System (INIS)

Yadav, Harish Kumar; Sreenivas, K; Katiyar, R S; Gupta, Vinay

2007-01-01

We study the influence of Mn doping on the vibrational properties of rf sputtered ZnO thin films. Raman spectra of the Mn doped ZnO samples reveal two additional vibrational modes, in addition to the host phonon modes, at 252 and 524 cm -1 . The intensity of the additional modes increases continuously with Mn concentration in ZnO and can be used as an indication of Mn incorporation in ZnO. The modes are assigned to the activation of ZnO silent modes due to relaxation of Raman selection rules produced by the breakdown of the translational symmetry of the crystal lattice with the incorporation of Mn at the Zn site. Furthermore, the A 1 (LO) mode is observed with very high intensity in the Raman spectra of undoped ZnO thin film and is attributed to the built-in electric field at the grain boundaries

Optical properties of oxide magnetic ZnO, Zn{sub 0.95}Mn{sub 0.05}O and Cu{sub 2}O nanopowders

Energy Technology Data Exchange (ETDEWEB)

Sokolov, V.I., E-mail: visokolov@imp.uran.r [Institute of Metal Physics UD RAS, S.Kovalevskaya Str. 18, 620041 Yekaterinburg (Russian Federation); Yermakov, A.Ye.; Uimin, M.A.; Mysik, A.A. [Institute of Metal Physics UD RAS, S.Kovalevskaya Str. 18, 620041 Yekaterinburg (Russian Federation); Pustovarov, V.A. [Ural State Technical University, Mira Street 19, 620002 Yekaterinburg (Russian Federation); Chukichev, M.V. [M.V. Lomonosov Moscow State University, Physics Faculty, 119991 Moscow (Russian Federation); Gruzdev, N.B. [Institute of Metal Physics UD RAS, S.Kovalevskaya Str. 18, 620041 Yekaterinburg (Russian Federation)

2009-12-15

ZnO, Zn{sub 0.95}Mn{sub 0.05}O and Cu{sub 2}O nanocrystals are synthesized. Excitonic lines in absorption spectra of these materials are detected. In photoluminescence and photoluminescence excitation spectra of Zn{sub 0.95}Mn{sub 0.05}O the dangling bond hybrid (DBH) state is found. It has splitted out from the top of the valence band due to the hybridization between d-states of the Mn impurity and the p-states of oxygen.

Stabilization of lead (Pb) and zinc (Zn) in contaminated rice paddy soil using starfish: A preliminary study.

Science.gov (United States)

Moon, Deok Hyun; Hwang, Inseong; Koutsospyros, Agamemnon; Cheong, Kyung Hoon; Ok, Yong Sik; Ji, Won Hyun; Park, Jeong-Hun

2018-05-01

Lead (Pb) and zinc (Zn) contaminated rice paddy soil was stabilized using natural (NSF) and calcined starfish (CSF). Contaminated soil was treated with NSF in the range of 0-10 wt% and CSF in the range of 0-5 wt% and cured for 28 days. Toxicity characteristic leaching procedure (TCLP) test was used to evaluate effectiveness of starfish treatment. Scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) analyses were conducted to investigate the mechanism responsible for effective immobilization of Pb and Zn. Experimental results suggest that NSF and CSF treatments effectively immobilize Pb and Zn in treated rice paddy soil. TCLP levels for Pb and Zn were reduced with increasing NSF and CSF dosage. Comparison of the two treatment methods reveals that CSF treatment is more effective than NSF treatment. Leachability of the two metals is reduced approximately 58% for Pb and 51% for Zn, upon 10 wt% NSF treatment. More pronounced leachability reductions, 93% for Pb and 76% for Zn, are achieved upon treatment with 5 wt% CSF. Sequential extraction results reveal that NSF and CSF treatments of contaminated soil generated decrease in exchangeable/weak acid Pb and Zn soluble fractions, and increase of residual Pb and Zn fractions. Results for the SEM-EDX sample treated with 5 wt% CSF indicate that effective Pb and Zn immobilization is most probably associated with calcium silicate hydrates (CSHs) and calcium aluminum hydrates (CAHs). Copyright © 2018 Elsevier Ltd. All rights reserved.

First-principle study on magnetic properties of Mn/Fe codoped ZnS

Energy Technology Data Exchange (ETDEWEB)

Chen Hongxia, E-mail: chenhongxia1@sina.com [College of Physical Science and Electronic Techniques, Yancheng Teachers University, Yancheng 224002 (China); Department of Physics, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China)

2012-07-15

We studied the magnetic properties of Mn/Fe codoped ZnS comparatively with and without defects using first-principle calculation. The calculated results indicate that the Mn/Fe codoped ZnS system tends to stabilize in a ferrimagnetic (FiM) configuration. To obtain a ferromagnetic (FM) configuration, we consider the doped system with defects, such as S or Zn vacancy. The calculated results indicate that the doped system with Zn vacancy favors FiM states. Although the FM states of the doped system with S vacancy are more stable than the FiM states in negative charge states, the FM states are not stable enough to exist. Finally, we replaced an S atom by a C atom in the doped system. The C atom prefers to substitute the S atom connecting Mn and Fe atoms. The formation energy of this defect is -0.40 eV, showing that Mn/Fe/C codoped ZnS can be fabricated easily by experiments. Furthermore, the FM state was lower in energy than the FiM state by 114 meV. Such a large energy difference between the FM and FiM states implies that room temperature ferromagnetism could be expected in such a system. - Highlights: Black-Right-Pointing-Pointer Mn/Fe codoped ZnS system tends to stabilize in a ferrimagnetic configuration with or without defects. Black-Right-Pointing-Pointer By additional C codoping, the doped system tends to stabilize in a ferromagnetic configuration. Black-Right-Pointing-Pointer Energy difference between ferrimagnetic and ferromagnetic states is 114 meV. Black-Right-Pointing-Pointer This indicates room temperature ferromagnetism can be likely in such a system.

Magnetic properties and loss separation in FeSi/MnZnFe2O4 soft magnetic composites

International Nuclear Information System (INIS)

Lauda, M.; Füzer, J.; Kollár, P.; Strečková, M.; Bureš, R.; Kováč, J.; Baťková, M.; Baťko, I.

2016-01-01

We investigated composites that have been prepared from FeSi powders covered with MnZnFe 2 O 4 (MnZn ferrite), which was prepared by sol–gel synthesis accompanied with the auto-combustion process. The aim of this paper is to analyze the complex permeability and core losses of prepared samples with different amount of MnZn ferrite. The microstructure and the powder morphology were examined by scanning electron microscopy. Magnetic measurements on bulk samples were carried out using a vibrating sample magnetometer, an impedance analyzer and hysteresisgraphs. The results indicate that the composites with 2.6 wt% MnZn ferrite show better soft magnetic properties than the composites with about 6 wt% MnZn ferrite. - Highlights: • Successful preparation of soft magnetic composite FeSi/MnZnFe 2 O 4 . • Study of the complex magnetic permeability. • Comparison of different compositions of prepared SMC's. • Determination of parts of magnetic losses.

Removal of aqueous Pb(II) by adsorption on Al{sub 2}O{sub 3}-pillared layered MnO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Haipeng; Gu, Liqin; Zhang, Ling; Zheng, Shourong; Wan, Haiqin; Sun, Jingya [State Key Laboratory of Pollution Control and Resource Reuse, Jiangsu Key Laboratory of Vehicle Emissions Control, School of the Environment, Nanjing University, Nanjing 210023 (China); Zhu, Dongqiang [School of Urban and Environmental Sciences, Peking University, Beijing 100871 (China); Xu, Zhaoyi, E-mail: zhaoyixu@nju.edu.cn [State Key Laboratory of Pollution Control and Resource Reuse, Jiangsu Key Laboratory of Vehicle Emissions Control, School of the Environment, Nanjing University, Nanjing 210023 (China)

2017-06-01

Highlights: • Al{sub 2}O{sub 3}-pillared layered MnO{sub 2} (p-MnO{sub 2}) was prepared from δ-MnO{sub 2} precursor. • p-MnO{sub 2} showed markedly higher Pb(II) adsorption capacity than pristine δ-MnO{sub 2.}. • Pillaring of Al{sub 2}O{sub 3} into the layer of δ-MnO{sub 2} enhanced the Pb(II) adsorption. - Abstract: In the present study, Al{sub 2}O{sub 3}-pillared layered MnO{sub 2} (p-MnO{sub 2}) was synthesized using δ-MnO{sub 2} as precursor and Pb(II) adsorption on p-MnO{sub 2} and δ-MnO{sub 2} was investigated. To clarify the adsorption mechanism, Al{sub 2}O{sub 3} was also prepared as an additional sorbent. The adsorbents were characterized by X-ray fluorescence analysis, powder X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy and N{sub 2} adsorption-desorption. Results showed that in comparison with pristine δ-MnO{sub 2}, Al{sub 2}O{sub 3} pillaring led to increased BET surface area of 166.3 m{sup 2} g{sup −1} and enlarged basal spacing of 0.85 nm. Accordingly, p-MnO{sub 2} exhibited a higher adsorption capacity of Pb(II) than δ-MnO{sub 2}. The adsorption isotherms of Pb(II) on δ-MnO{sub 2} and Al{sub 2}O{sub 3} pillar fitted well to the Freundlich model, while the adsorption isotherm of Pb(II) on p-MnO{sub 2} could be well described using a dual-adsorption model, attributed to Pb(II) adsorption on both δ-MnO{sub 2} and Al{sub 2}O{sub 3}. Additionally, Pb(II) adsorption on δ-MnO{sub 2} and p-MnO{sub 2} followed the pseudo second-order kinetics, and a lower adsorption rate was observed on p-MnO{sub 2} than δ-MnO{sub 2}. The Pb(II) adsorption capacity of p-MnO{sub 2} increased with solution pH and co-existing cation concentration, and the presence of dissolved humic acid (10.2 mg L{sup −1}) did not markedly impact Pb(II) adsorption. p-MnO{sub 2} also displayed good adsorption capacities for aqueous Cu(II) and Cd(II). Findings in this study indicate that p-MnO{sub 2} could be used as a highly effective

Highly stabilized and photoluminescence enhancement of ZnS:Mn2+ nanoparticles in biotin matrix

International Nuclear Information System (INIS)

Keshari, Ashish K.; Pandey, Avinash C.

2009-01-01

We synthesized the ZnS:Mn 2+ nanoparticles passivated by biocompatible layer, namely, biotin by chemical precipitation route and studied their temporal evolution for size, structure, optical, and photoluminescence stability. To monitor the structural and optoelectronic properties of the nanoparticles with time, we have characterized the grown product by x-ray diffraction, small angle x-ray scattering, UV visible, and photoluminescence spectroscopic techniques at a regular interval for a period of three months. Results showed that the properties of nanophosphors capped with biotin are remaining the same even after 3 months. Energy dispersive x-ray analysis of 3 month aged sample shows long time compatibility between ZnS:Mn 2+ nanoparticles and the biotin. This is also confirmed by electron microscopy that the growth of the nanoparticles is strongly arrested by the biotin. X-ray photoelectron spectra were also recorded to show the chemical state of the elements. Enhanced ratio of Zn 2p to Mn 2p peaks in the x-ray photoelectron spectra of ZnS:Mn 2+ nanoparticles shows that the Mn 2+ ions are incorporated within ZnS host matrix. We found that biotin capping will enhance the luminescence from ZnS:Mn 2+ nanoparticles as compared to without capped particles. Absence of biotin will gradually degrade the luminescence upon aging while drastic degradation in luminescence intensity was observed after annealing. Properties show that biotin also protected the nanoparticles from any environmental attack

Biocompatible ZnS:Mn quantum dots for reactive oxygen generation and detection in aqueous media

Energy Technology Data Exchange (ETDEWEB)

Diaz-Diestra, Daysi; Beltran-Huarac, Juan, E-mail: juan.beltran1@upr.edu; Bracho-Rincon, Dina P.; González-Feliciano, José A.; González, Carlos I.; Weiner, Brad R.; Morell, Gerardo [University of Puerto Rico, Molecular Sciences Research Center (United States)

2015-12-15

We report here the versatility of Mn-doped ZnS quantum dots (ZnS:Mn QDs) synthesized in aqueous medium for generating reactive oxygen species and for detecting cells. Our experiments provide evidence leading to the elimination of Cd-based cores in CdSe/ZnS systems by substitution of Mn-doped ZnS. Advanced electron microscopy, X-ray diffraction, and optical spectroscopy were applied to elucidate the formation, morphology, and dispersion of the products. We study for the first time the ability of ZnS:Mn QDs to act as immobilizing agents for Tyrosinase (Tyr) enzyme. It was found that ZnS:Mn QDs show no deactivation of Tyr enzyme, which efficiently catalyzed the hydrogen peroxide (H{sub 2}O{sub 2}) oxidation and its eventual reduction (−0.063 V vs. Ag/AgCl) on the biosensor surface. The biosensor showed a linear response in the range of 12 μmol/L–0.1 mmol/L at low operation potential. Our observations are explained in terms of a catalase-cycled kinetic mechanism based on the binding of H{sub 2}O{sub 2} to the axial position of one of the active copper sites of the oxy-Tyr during the catalase cycle to produce deoxy-Tyr. A singlet oxygen quantum yield of 0.62 in buffer and 0.54 in water was found when ZnS:Mn QDs were employed as a photosensitizer in the presence of a chemical scavenger and a standard dye. These results are consistent with a chemical trapping energy transfer mechanism. Our results also indicate that ZnS:Mn QDs are well tolerated by HeLa Cells reaching cell viabilities as high as 88 % at 300 µg/mL of QDs for 24 h of incubation. The ability of ZnS:Mn QDs as luminescent nanoprobes for bioimaging is also discussed.Graphical Abstract.

Kinetics of physico-chemical processes during intensive mechanical processing of ZnO-MnO2 powder mixture

International Nuclear Information System (INIS)

Kakazey, M.; Vlasova, M.; Dominguez-Patino, M.; Juarez-Arellano, E.A.; Bykov, A.; Leon, I.; Siqueiros-Diaz, A.

2011-01-01

Experimental results of electron paramagnetic resonance spectra, X-ray diffraction, scanning electron microscopy and infrared spectroscopy demonstrate that the kinetic of the physical and chemical processes that takes place during prolonged intensive mechanical processing (MP, 0 MP >3120min) of powder mixtures of 50%wt ZnO+50%wt MnO 2 can be described as a three stage process. (1) 0 MP >30min, particles destruction, formation of superficial defects, fast increment of sample average temperature (from 290 to ∼600K) and annealing of defects with the lowest energy of activation E ac . (2) 30 MP >390min, further particle destruction, slow increment of sample average temperature (from ∼600 to ∼700K), formation and growth of a very disordered layer of β-MnO 2 around ZnO particles, dehydration of MnO 2 , formation of solid solution of Mn 2+ ions in ZnO, formation of nano-quasiamorphous states in the ZnO-MnO 2 mixture and onset of the formation of the ZnMnO 3 phase. (3) 390 MP >3120min, the sample average temperature remains constant (∼700K), the reaction is completed and the spinel ZnMnO 3 phase with a unit cell a=8.431(1) A and space group Fd3-barm is the only phase present in the sample. No ferromagnetism at room temperature was detected in this study. - Highlights: → The kinetics during mechanical processing of ZnO-MnO 2 samples is a three stage process. → First stage, reduction of crystallites size and accumulation of defects. → Second stage, nano-quasiamorphous states formation and onset of the ZnMnO 3 phase. → Third stage, complete reaction to the spinel ZnMnO 3 phase.

Local fields in Co and Mn Co-doped ZnO

Energy Technology Data Exchange (ETDEWEB)

Sato, W., E-mail: wsato@se.kanazawa-u.ac.jp [Kanazawa University, Institute of Science and Engineering (Japan); Kano, Y.; Suzuki, T.; Nakagawa, M. [Kanazawa University, Graduate School of Natural Science and Technology (Japan); Kobayashi, Y. [The University of Electro-Communications, Department of Engineering Science (Japan)

2016-12-15

The magnetic properties of ZnO co-doped with 5 at. % Co and 5 at. % Mn(Zn{sub 0.90}Co{sub 0.05}Mn{sub 0.05}O) synthesized by a solid-state reaction were investigated by means of {sup 57}Co emission Mössbauer spectroscopy. The majority of the probe ions (80 %) residing in defect-free substitutional Zn sites take the oxidation state of {sup 57}Fe {sup 2+}, and the others presumably form local defects taking the state of {sup 57}Fe {sup 3+} at room temperature. Both components show doublets, and RT ferromagnetism was thus absent in the sample. For the measurement at 10 K, spectral broadening was observed, implying a possible presence of a weak magnetic component.

Effects of Cu, Zn and Pb Combined Pollution on Soil Hydrolase Activities

Directory of Open Access Journals (Sweden)

FENG Dan

2015-08-01

Full Text Available To study the relations between soil enzyme activities and heavy metal pollution, the combined effects of Cu, Zn and Pb on the three hydrolase activities, including invertase(IN, urease(Uand alkaline phosphatase(ALPwere investigated via an orthogonal experiment. Results showed as the following: When the concentration of Cu was 400 mg·kg-1, the U and ALP activities were decreased 51% and 44%, separately; When Zn was at 500 mg·kg-1, IN and ALP activities were only decreased 3% and 9%, while U activity was increased; When Pb was at 500 mg·kg-1, IN and U activities were increased, while ALP activity was decreased 13%. As a whole, Cu was considered as the most remarkable influence factor for IN, U and ALP activity regardless of interactions among the heavy metals, Zn came second, and Pb mainly showed activation. Considering interactions, Cu×Zn could significantly influence U activity(P<0.05, effects of Cu×Pb and Cu×Zn on ALP activity were remarkable(95% confidence interval. The response of ALP activity was more sensitive than the other two enzymes. Soil ALP activity might be a sensitive tool for assessing the pollution degree of Cu.

Structural and magnetic properties in Mn-doped ZnO films prepared by pulsed-laser deposition

International Nuclear Information System (INIS)

Li, Qiang; Wang, Yuyin; Liu, Jiandang; Kong, Wei; Ye, Bangjiao

2014-01-01

We investigated the structural and magnetic properties of Zn 0.95 Mn 0.05 O films prepared on sapphire substrates by pulsed-laser deposition. Only low temperature ferromagnetism (Curie temperature lower than 50 K) was observed in Mn-doped samples, while pure ZnO film shows a typical paramagnetic behavior. Structural analyses indicate that the substitutional Mn 2+ ions play a significant role for the low temperature ferromagnetism. Lattice defects such as V O and V Zn were not proven to be effective factors for the origin of ferromagnetism in the films. The low temperature ferromagnetism might be interpreted as p–d hybridization from indirect coupling of Mn ions (Mn–O–Mn).

[Adsorption of heavy metals on the surface of birnessite relationship with its Mn average oxidation state and adsorption sites].

Science.gov (United States)

Wang, Yan; Tan, Wen-Feng; Feng, Xiong-Han; Qiu, Guo-Hong; Liu, Fan

2011-10-01

Adsorption characteristics of mineral surface for heavy metal ions are largely determined by the type and amount of surface adsorption sites. However, the effects of substructure variance in manganese oxide on the adsorption sites and adsorption characteristics remain unclear. Adsorption experiments and powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) were combined to examine the adsorption characteristics of Pb2+, Cu2+, Zn2+ and Cd2+ sequestration by birnessites with different Mn average oxidation state (AOS), and the Mn AOS dependent adsorption sites and adsorption characteristics. The results show that the maximum adsorption capacity of Pb2+, Cu2+, Zn2+ and Cd2+ increased with increasing birnessite Mn AOS. The adsorption capacity followed the order of Pb2+ > Cu2+ > Zn2+ > Cd2+. The observations suggest that there exist two sites on the surface of birnessite, i. e., high-binding-energy site (HBE site) and low-binding-energy site (LBE site). With the increase of Mn AOS for birnessites, the amount of HBE sites for heavy metal ions adsorption remarkably increased. On the other hand, variation in the amount of LBE sites was insignificant. The amount of LBE sites is much more than those of HBE sites on the surface of birnessite with low Mn AOS. Nevertheless, both amounts on the surface of birnessite with high Mn AOS are very close to each other. Therefore, the heavy metal ions adsorption capacity on birnessite is largely determined by the amount of HBE sites. On birnessite surface, adsorption of Cu2+, Zn2+, and Cd2+ mostly occurred at HBE sites. In comparison with Zn2+ and Cd2+, more Cu2+ adsorbed on the LBW sites. Pb2+ adsorption maybe occupy at both LBE sites and HBE sites simultaneously.

Contamination of the soil along the river Zletovska by metals as by products of economic production of Pb-Zn

OpenAIRE

Boev, Blazo; Lepitkova, Sonja

1996-01-01

This paper shows the results constraining the degree of contamination of soil along the course of the River Zletovska by some mewls. These are by- products of economic production of lead-zinc ores which are common in this area. Contamination of soils by some metals, first of all by Pb, Zn, Cu, Cd, As, Fe, Al, Mn, Na, K is an important issue for the quality of the environment in which we live from several aspects: accumulation of waters under river alluvions; agricultural produ...

Structure, composition, morphology, photoluminescence and cathodoluminescence properties of ZnGeN{sub 2} and ZnGeN{sub 2}:Mn{sup 2+} for field emission displays

Energy Technology Data Exchange (ETDEWEB)

Zhang, Q.-H. [MOE Key Laboratory of Bioinorganic and Synthetic Chemistry, State Key Laboratory of Optoelectronic Materials and Technologies, School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou, Guangdong 510275 (China); Guangzhou Research Institute of Non-ferrous Metals, Guangzhou, Guangdong 510651 (China); Wang, J., E-mail: ceswj@mail.sysu.edu.cn [MOE Key Laboratory of Bioinorganic and Synthetic Chemistry, State Key Laboratory of Optoelectronic Materials and Technologies, School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou, Guangdong 510275 (China); Yeh, C.-W.; Ke, W.-C.; Liu, R.-S. [Department of Chemistry, National Taiwan University, Taipei 106, Taiwan (China); Tang, J.-K. [Department of Physics and Astronomy, University of Wyoming, Laramie, WY 82071 (United States); Xie, M.-B.; Liang, H.-B.; Su, Q. [MOE Key Laboratory of Bioinorganic and Synthetic Chemistry, State Key Laboratory of Optoelectronic Materials and Technologies, School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou, Guangdong 510275 (China)

2010-12-15

Yellowish-orange-emitting ZnGeN{sub 2} and orange-red-emitting ZnGeN{sub 2}:Mn were synthesized by a facile and mild gas-reduction-nitridation reaction at 1153 K under NH{sub 3} flow with air-stable raw materials ZnO, GeO{sub 2} and MnCO{sub 3}. The structure, composition, morphology, photoluminescence and cathodoluminescence properties of ZnGeN{sub 2} doped with or without Mn{sup 2+} were systematically investigated. Rietveld refinements show that the as-synthesized samples are obtained as single-phase compounds and crystallize as an orthorhombic structure with a space group of Pna2{sub 1}. The actual chemical composition of the as-prepared ZnGeN{sub 2} determined by energy dispersive X-ray spectroscopy suggests that the Ge vacancy defects probably exist in the host. The SEM image reveals that the Zn{sub 0.99}Mn{sub 0.01}GeN{sub 2} particles form aggregates {approx}500-600 nm in size. The diffuse reflection spectrum and photoluminescence excitation spectrum confirm that the band edge absorption of ZnGeN{sub 2} at low energy is 3.3 eV ({approx}376 nm). Upon UV light excitation and electron beam excitation, ZnGeN{sub 2} gives an intense yellowish-orange emission around 580-600 nm, associated with a deep defect level due to the Ge vacancy defects, and ZnGeN{sub 2}:Mn shows an intense red emission at 610 nm due to the {sup 4}T{sub 1g}({sup 4}G) {yields} 6A{sub 1g}({sup 6}S) of Mn{sup 2+}. The unusual red emission of Mn{sup 2+} in tetrahedral Zn{sup 2+} sites is attributed to the strong nephelauxetic effect between Mn{sup 2+} and the surrounding tetrahedrally coordinated nitrogen. The photoluminescence and cathodoluminescence emission colors of ZnGeN{sub 2}:Mn have a high color purity of {approx}93-98%. These results demonstrate that ZnGeN{sub 2}:Mn is a novel, promising red-emitting nitride, potentially applicable to field emission displays with brilliant color-rendering properties and a large color gamut.

Leaching behavior of U, Mn, Sr, and Pb from different particle-size fractions of uranium mill tailings.

Science.gov (United States)

Liu, Bo; Peng, Tongjiang; Sun, Hongjuan

2017-06-01

Pollution by the release of heavy metals from tailings constitutes a potential threat to the environment. To characterize the processes governing the release of Mn, Sr, Pb, and U from the uranium mill tailings, a dynamic leaching test was applied for different size of uranium mill tailings samples. Inductively coupled plasma atomic emission spectroscopy (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS) were performed to determine the content of Mn, Sr, Pb, and U in the leachates. The release of mobile Mn, Sr, Pb, and U fraction was slow, being faster in the initial stage and then attained a near steady-state condition. The experimental results demonstrate that the release of Mn, Sr, Pb, and U from uranium mill tailings with different size fractions is controlled by a variety of mechanisms. Surface wash-off is the release mechanism for Mn. The main release mechanism of Sr and Pb is the dissolution in the initial leaching stage. For U, a mixed process of wash-off and diffusion is the controlling mechanism.

Use of cattails in treating wastewater from a Pb/Zn mine

Science.gov (United States)

Lan, Chongyu; Chen, Guizhu; Li, Liuchun; Wong, M. H.

1992-01-01

This article describes the use of a combined treatment system, which includes an aquatic treatment pond with Typha latifolia Linn. (Typhaceae) as the dominant species and a stabilization pond, to treat the wastewater from a Pn/Zn mine at Shaoguan, Guangdong Province, China. In 1983, it was noted that T. latifolia bloomed in areas affected by the wastewater emitted from the mine, hence a combined purification system was subsequently built. The influent contained high levels of total suspended solids (4635 mg/liter), chemical oxygen demand (14.5 mg/liter) as well as Pb (1.6 mg/liter) and Zn (1.9 mg/liter). The results of the effluent after treatment showed that the total suspended solids, chemical oxygen demand, Pb, and Zn had been reduced by 99%, 55%, 95%, and 80% respectively. The results of plant tissue analysis indicled that T. latifolia assimilated significant amounts of Pb and Zn, especially in the root portion. During 1986 several species of algae and fish were present in the pond, usually with a higher density in areas containing lower metal concentrations in the water.

Fate of Heavy Metals Pb and Zn in the West Season at Jeneberang Estuary, Makassar

Directory of Open Access Journals (Sweden)

Najamuddin .

2017-08-01

Full Text Available The pollutant quantity of heavy metals entering water environment does not give complete answer toward the generated effect and risk, however it needs thoroughly study related to the pollutant dynamic. The aim of this research was to investigate the fate of Pb and Zn in water, such as: distribution, behavior, and reactivity (case study: Jeneberang Estuary, Makassar. Pb and Zn concentrations were determined using Atomic Absorption Spectrophotometry (AAS. The distribution of dissolved Pb and Zn showed a pattern that the lowest concentration was in the fresh water (the river zone, whereas the highest concentration was in the salt water (the marine zone. The distribution pattern of particulate Pb and Zn showed that the highest concentration was in the fresh water (the river zone and the salt water (the marine zone, whereas the lowest concentration was in the estuary zone. The behavior of dissolved Pb and Zn tended to increase the concentration (desorption along the increased salinity gradient. The residual fraction was the dominant component of geochemical fractions in the sediment that indicated the sources of Pb and Zn mainly derived from a natural process and the reactivity was low in the water.   Keywords: distribution, behavior, reactivity, lead, zinc, pollution

Elucidation of the enhanced ferromagnetic origin in Mn-doped ZnO nanocrystals embedded into a SiO2 matrix

International Nuclear Information System (INIS)

Lee, Sejoon; Lee, Youngmin; Kim, Deukyoung

2013-01-01

The origin of the enhanced room temperature ferromagnetism in Mn-doped ZnO (ZnO:Mn) nanocrystals is investigated. ZnO:Mn nanocrystals, which were fabricated by using a laser irradiation method with a 248-nm KrF excimer laser, exhibited two-times increase in the spontaneous magnetization (∼0.4 emu/cm 3 at 300 K) compared to the ZnO:Mn thin film (∼0.2 emu/cm 3 at 300 K). The increased exchange integral of J 1 /k B = 51.6 K in ZnO:Mn nanocrystals, in comparison with the ZnO:Mn thin film (J 1 /k B = 46.9 K), is indicative of the enhanced ferromagnetic exchange interaction. This is attributed to the large number of acceptor defects in the SiO 2 -capped ZnO:Mn nanocrystals. Namely, the holes bound to the acceptor defects form microscopic bound-magnetic-polarons with Mn ions; hence, long-range ferromagnetic coupling is enhanced. The results suggest that ferromagnetism in ZnO-based dilute magnetic semiconductors can be controlled by modulating the density of native point defects, which can be chemically and thermodynamically modified during the material synthesis or preparation.

Super-bright and short-lived photoluminescence of textured Zn2SiO4:Mn2+ phosphor film on quartz glass

Science.gov (United States)

Park, Jehong; Park, Kwangwon; Lee, Jaebum; Kim, Jongsu; Seo, Kwangil; Kwon, Kevin; Kung, Patrick; Kim, Seongsin M.

2010-02-01

Green-emissive textured Zn2SiO4:Mn2+ phosphor film was fabricated by a thermal diffusion of ZnO:Mn on quartz glass. The characterization has been performed in terms of Mn2+ ions concentration (Mn/Zn=1~9 mol %). As an increase of Mn2+ ions concentration in the Zn2SiO4:Mn2+ phosphor film, the emission peak was red shifted from 519 nm to 526 nm, and the decay time to 10% of the maximum intensity was shorter from 20 ms to 0.5 ms. All annealed Zn2SiO4:Mn2+ phosphor films became textured along some hexagonal directions on the amorphous quartz glass. The brightest Zn2SiO4:Mn2+ film at optimal Mn2+ concentration of 5 % showed the photoluminescence brightness of 65 % and the shortened decay time of 4.4 ms in comparison with a commercially Zn2SiO4: Mn2+ powder phosphor screen. The excellencies can be attributed to a unique textured structure.

Photoluminescence study of epitaxially grown ZnSnAs2:Mn thin films

International Nuclear Information System (INIS)

Mammadov, E; Haneta, M; Toyota, H; Uchitomi, N

2011-01-01

The photoluminescence (PL) properties of heavily Mn-doped ZnSnAs 2 layers epitaxially grown on nearly lattice-matched semi-insulating InP substrates are studied. PL spectra are obtained for samples with Mn concentrations of 5, 12 and 24 mol% relative to the combined concentrations of Zn and Sn. A broad emission band centered at ∼ 1 eV is detected for Mn-doped layers at room temperature. The emission is a intense broad asymmetric line at low temperatures. The line is reconstructed by superposition of two bands with peak energies of ∼ 0.99 and 1.07 eV, similar to those reported for InP. These bands are superimposed onto a 1.14 eV band with well-resolved phonon structure for the layer doped with 12 % Mn. Recombination mechanism involving the split-off band of the ZnSnAs 2 is suggested. Temperature dependence of integrated intensities of the PL bands indicates to thermally activated emission with activation energies somewhat different from those found for InP. Mn substitution at cationic sites increases the concentration of holes which may act as recombination centers. Recombination to the holes bound to Mn ions with the ground state located below the top of the valence band has been proposed as a possible PL mechanism.

An electroluminescence device for printable electronics using coprecipitated ZnS:Mn nanocrystal ink

International Nuclear Information System (INIS)

Toyama, T; Hama, T; Adachi, D; Nakashizu, Y; Okamoto, H

2009-01-01

Electroluminescence (EL) devices for printable electronics using coprecipitated ZnS:Mn nanocrystal (NC) ink are demonstrated. The EL properties of these devices were investigated along with the structural and optical properties of ZnS:Mn NCs with an emphasis on their dependence on crystal size. Transmission electron microscopy and x-ray diffraction studies revealed that the NCs, with a crystal size of 3-4 nm, are nearly monodisperse; the crystal size can be controlled by the Zn 2+ concentration in the starting solution for coprecipitation. The results of optical studies indicate the presence of quantum confinement effects; in addition, the NC surfaces are well passivated, regardless of the crystal size. Finally, an increase in the luminance of EL devices with a decrease in crystal size is observed, which suggests the excitation mechanism of ZnS:Mn NC EL devices.

Hydrothermal synthesis of Mn-doped ZnCo2O4 electrode material for high-performance supercapacitor

Science.gov (United States)

Mary, A. Juliet Christina; Bose, A. Chandra

2017-12-01

Mn-doped ZnCo2O4 nanoparticle has been synthesized by hydrothermal method without adding any surfactants. Structural, morphological and electrochemical performances have been studied for the pure and various concentration of Mn-doped ZnCo2O4 nanoparticles. XRD and Raman studies demonstrate the crystalline structure of the material. Specific capacitance of the 10 wt% Mn doped ZnCo2O4 nanomaterial is analysed using the three-electrode system. 10 wt% Mn-doped ZnCo2O4 has a maximum capacitance of 707.4 F g-1 at a current density of 0.5 A g-1. Coulombic efficiency of the material is 96.3% for 500 cycles in the KOH electrolyte medium. A two-electrode device using 10 wt% Mn-doped ZnCo2O4 exhibits the highest specific capacitance of 6.5 F g-1 at a current density of 0.03 A g-1 which is the suitable material for supercapacitor application.

Low-temperature synthesis of Zn{sub 2}SiO{sub 4}:Mn green photoluminescence phosphor

Energy Technology Data Exchange (ETDEWEB)

Sivakumar, V. [Saveetha Engineering College, Thandalam, Chennai 602105 (India); Lakshmanan, Arunachalam, E-mail: arunachalamlakshmanan@yahoo.com [Saveetha Engineering College, Thandalam, Chennai 602105 (India); Kalpana, S.; Sangeetha Rani, R.; Satheesh Kumar, R. [Saveetha Engineering College, Thandalam, Chennai 602105 (India); Jose, M.T. [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)

2012-08-15

Zn{sub 2}SiO{sub 4}:Mn green phosphor having comparable photoluminescence (PL) efficiency with commercial phosphor has been synthesized at 1000 Degree-Sign C using solid state reactions involving ZnO, silicic acid and manganese acetate. The water of crystallization attached to SiO{sub 2} in silicic acid whose dissociation at 1000 Degree-Sign C seem to promote the sintering efficiency of Zn{sub 2}SiO{sub 4}:Mn. Incremental ZnO addition and re-firing at 1000 Degree-Sign C promote the diffusion rate of ZnO and SiO{sub 2}. The formation of a single crystalline phase of willemite structure in the samples was confirmed by powder XRD measurements. The phosphor exhibit an intense excitation band centered around 275 nm and a relatively weak excitation centered around 380 nm while the broad band green emission peaks at 524 nm. Other parameters studied include PL spectra, grain morphology, ZnO/SiO{sub 2} molar ratio, Mn concentration, co-dopant/flux and the effect of chemical forms of Mn dopant as well as silica on the PL efficiency. - Highlights: Black-Right-Pointing-Pointer Synthesis of Zn{sub 2}SiO{sub 4}:Mn by solid state sintering at a low temperature of 1000 Degree-Sign C in air. Black-Right-Pointing-Pointer Dissociation of water of crystallization in silicic acid promote sintering efficiency. Black-Right-Pointing-Pointer Photoluminescence efficiency comparable with that of the commercial phosphor. Black-Right-Pointing-Pointer Enhancement in luminescence with MgCO{sub 3} co-doping and refiring as well as ZnO addition. Black-Right-Pointing-Pointer XRD confirm single phase willemite structure (rhombohedral) of Zn{sub 2}SiO{sub 4}:Mn.

Bio-corrosion characterization of Mg-Zn-X (X = Ca, Mn, Si) alloys for biomedical applications.

Science.gov (United States)

Rosalbino, F; De Negri, S; Saccone, A; Angelini, E; Delfino, S

2010-04-01

The successful applications of magnesium-based alloys as biodegradable orthopedic implants are mainly inhibited due to their high degradation rates in physiological environment. This study examines the bio-corrosion behaviour of Mg-2Zn-0.2X (X = Ca, Mn, Si) alloys in Ringer's physiological solution that simulates bodily fluids, and compares it with that of AZ91 magnesium alloy. Potentiodynamic polarization and electrochemical impedance spectroscopy results showed a better corrosion behaviour of AZ91 alloy with respect to Mg-2Zn-0.2Ca and Mg-2Zn-0.2Si alloys. On the contrary, enhanced corrosion resistance was observed for Mg-2Zn-0.2Mn alloy compared to the AZ91 one: Mg-2Zn-0.2Mn alloy exhibited a four-fold increase in the polarization resistance than AZ91 alloy after 168 h exposure to the Ringer's physiological solution. The improved corrosion behaviour of the Mg-2Zn-0.2Mn alloy with respect to the AZ91 one can be ascribed to enhanced protective properties of the Mg(OH)(2) surface layer. The present study suggests the Mg-2Zn-0.2Mn alloy as a promising candidate for its applications in degradable orthopedic implants, and is worthwhile to further investigate the in vivo corrosion behaviour as well as assessed the mechanical properties of this alloy.

Estudo de metais pesados (Co, Cu, Fe, Cr, Ni, Mn, Pb e Zn na Bacia do Tarumã-Açu Manaus (AM Heavy metal (Co, Cu, Fe, Cr, Ni, Mn, Pb e Zn study in the Tarumã-Açu Basin Manaus (AM

Directory of Open Access Journals (Sweden)

Genilson Pereira Santana

2007-01-01

Full Text Available Os resíduos gerados em domicílios incluem diversos produtos, como pesticidas, produtos farmacêuticos, detergentes, óleos de cozinha, metais pesados contidos em baterias e outros utensílios. Esses resíduos são lançados continuamente em aterro sanitário ou lixões em cidades como Manaus. O chorume produzido nesses aterros, quando não tratados, contamina recursos hídricos superficiais e subterrâneos. Neste estudo foi feita uma avaliação das conseqüências da liberação do chorume no sistema hídrico da bacia do Tarumã-Açu. Amostras de água e sedimento foram coletadas nos igarapés Matrinxã, Acará, Bolívia, bacia do Tarumã-Açu e dentro do aterro sanitário (Manaus - Amazonas - Brasil em março 2001. As amostras de água foram filtradas em filtro Milipore (0,45 mm de poro e, em seguida, tratadas com HNO3 concentrado. As amostras de sedimento foram peneiradas em malha de 0,053 mm e digeridas com HCl:HNO3 (1:3 a 150ºC. As concentrações de alguns metais pesados (Co, Cu, Fe, Cr, Ni, Mn, Pb e Zn foram determinadas nas amostras de água e sedimento por espectrometria de absorção atômica de chama. Os resultados revelaram que a concentração dos metais pesados é muito acima dos permitidos pela resolução 357/2005 do CONAMA em praticamente todos os locais amostrados, mostrando que o Aterro Sanitário é um dos principais responsáveis pelo impacto ambiental observado nos corpos hídricos estudados. As análises dos componentes principais (PCA e hierárquica de cluster (HCA, revelam que os pontos de coleta localizados dentro do aterro sanitário apresentam características diferentes dos outros locais amostrados. Além disso, o HCA e PCA mostraram que existe uma similaridade entre os pontos de coleta localizados fora do aterro o que permite afirmar que o chorume do aterro se dissolve por todo corpo hídrico estudado.Domestic sewage involves several products, such as pesticides, pharmaceutics products, detergents, soybean oil

Evidence for microbial activity in the formation of carbonate-hosted Zn-Pb deposits

Science.gov (United States)

Kucha, H.; Raith, J.

2009-04-01

*Kucha H **Raith J *University of Mining and Metallurgy, Faculty of Geology, Geophysics and Environmental Protection, Mickiewicza 30, PL-30-059 Krakow, Poland. ** University of Leoben, Department of Applied Geosciences and Geophysics, A-8700 Leoben, Peter Tunner Str. 5, Austria Evidence for microbial activity in the formation of carbonate-hosted Zn-Pb deposits To date evaluation of bacterial processes in the formation of carbonate-hosted Zn-Pb deposits is largely based on sulphur isotope evidence. However, during a past few years, textural criteria, have been established, which support the bacterial origin of many of these deposits. This has received a strong support from micro-, and nano-textures of naturally growing bacterial films in a flooded tunnel within carbonates that host the Piquette Zn-Pb deposit (Druschel et al., 2002). Bacterial textures, micro- and nano textures found in carbonate-hosted Zn-Pb deposits are: i)wavy bacterial films up to a few mm thick to up to a few cm long composed of peloids, ii)semimassive agglomeration of peloids in the carbonate matrix, and iii)solitary peloids dispersed in the carbonate matrix. Peloids are usually composed of a distinct 50-90um core most often made up of Zn-bearing calcite surrounded by 30-60um thick dentate rim composed of ZnS. Etching of Zn-carbonate cores reveals 1 - 2um ZnS filaments, and numerous 15 to 90nm large ZnS nano-spheres (Kucha et al., 2005). In massive ore composite Zn-calcite - sphalerite peloids are entirely replaced by zinc sulphide, and form peloids ghosts within banded sulphide layers. Bacterially derived micro- and nano-textures have been observed in the following carbonate-hosted Zn-Pb deposits: 1)Irish-type Zn-Pb deposits. In the Navan deposit the basic sulphur is isotopically light bacteriogenic S (Fallick at al., 2001). This is corroborated by semimassive agglomerations of composite peloids (Zn-calcite-ZnS corona or ZnS core-melnikovite corona). Etching of Zn-calcite core reveals globular

Physical properties of antiferromagnetic Mn doped ZnO samples: Role of impurity phase

International Nuclear Information System (INIS)

Neogi, S.K.; Karmakar, R.; Misra, A.K.; Banerjee, A.; Das, D.; Bandyopadhyay, S.

2013-01-01

Structural, morphological, optical, and magnetic properties of nanocrystalline Zn 1−x Mn x O samples (x=0.01, 0.02, 0.04, 0.06, 0.08 and 0.10) prepared by the sol–gel route are studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV–visible absorption spectroscopy, Superconducting quantum interference device (SQUID) magnetometry and positron annihilation lifetime spectroscopy (PALS). XRD confirms formation of wurzite structure in all the Mn-substituted samples. A systematic increase in lattice constants and decrease in grain size have been observed with increase in manganese doping concentration up to 6 at% in the ZnO structure. An impurity phase (ZnMnO 3 ) has been detected when percentage of Mn concentration is 6 at% or higher. The optical band gap of the Mn-substituted ZnO samples decrease with increase in doping concentration of manganese whereas the width of the localized states increases. The antiferromagnetic exchange interaction is strong in the samples for 2 and 4 at% of Mn doping but it reduces when the doping level increases from 6 at% and further. Positron life time components τ 1 and τ 2 are found to decrease when concentration of the dopant exceeds 6 at%. The changes in magnetic properties as well as positron annihilation parameters at higher manganese concentration have been assigned as due to the formation of impurity phase. - highlights: • Single phase structure has been observed up to 6 at% of Mn doping. • Impurity phase has been developed above 6 at% of Mn doping. • Antiferromagnetic and paramagnetic interactions are present in the samples. • Defect parameters show sharp fall as Mn concentration above 6 at%. • The magnetic and defect properties are modified by the formation of impurity phase

Physical properties of antiferromagnetic Mn doped ZnO samples: Role of impurity phase

Energy Technology Data Exchange (ETDEWEB)

Neogi, S.K.; Karmakar, R. [Department of Physics, University of Calcutta, 92 A.P.C. Road, Kolkata 700009 (India); Misra, A.K. [UGC DAE Consortium for Scientific Research, Salt Lake, Kolkata 700064 (India); Banerjee, A. [Department of Physics, University of Calcutta, 92 A.P.C. Road, Kolkata 700009 (India); CRNN, University of Calcutta, JD 2, Sector III, Salt Lake, Kolkata 700098 (India); Das, D. [UGC DAE Consortium for Scientific Research, Salt Lake, Kolkata 700064 (India); Bandyopadhyay, S., E-mail: sbaphy@caluniv.ac.in [Department of Physics, University of Calcutta, 92 A.P.C. Road, Kolkata 700009 (India); CRNN, University of Calcutta, JD 2, Sector III, Salt Lake, Kolkata 700098 (India)

2013-11-15

Structural, morphological, optical, and magnetic properties of nanocrystalline Zn{sub 1−x}Mn{sub x}O samples (x=0.01, 0.02, 0.04, 0.06, 0.08 and 0.10) prepared by the sol–gel route are studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV–visible absorption spectroscopy, Superconducting quantum interference device (SQUID) magnetometry and positron annihilation lifetime spectroscopy (PALS). XRD confirms formation of wurzite structure in all the Mn-substituted samples. A systematic increase in lattice constants and decrease in grain size have been observed with increase in manganese doping concentration up to 6 at% in the ZnO structure. An impurity phase (ZnMnO{sub 3}) has been detected when percentage of Mn concentration is 6 at% or higher. The optical band gap of the Mn-substituted ZnO samples decrease with increase in doping concentration of manganese whereas the width of the localized states increases. The antiferromagnetic exchange interaction is strong in the samples for 2 and 4 at% of Mn doping but it reduces when the doping level increases from 6 at% and further. Positron life time components τ{sub 1} and τ{sub 2} are found to decrease when concentration of the dopant exceeds 6 at%. The changes in magnetic properties as well as positron annihilation parameters at higher manganese concentration have been assigned as due to the formation of impurity phase. - highlights: • Single phase structure has been observed up to 6 at% of Mn doping. • Impurity phase has been developed above 6 at% of Mn doping. • Antiferromagnetic and paramagnetic interactions are present in the samples. • Defect parameters show sharp fall as Mn concentration above 6 at%. • The magnetic and defect properties are modified by the formation of impurity phase.

Kinetics of physico-chemical processes during intensive mechanical processing of ZnO-MnO{sub 2} powder mixture

Energy Technology Data Exchange (ETDEWEB)

Kakazey, M.; Vlasova, M.; Dominguez-Patino, M. [CIICAp-Universidad Autonoma del Estado de Morelos, Cuernavaca (Mexico); Juarez-Arellano, E.A., E-mail: eajuarez@unpa.edu.mx [Universidad del Papaloapan, Tuxtepec, Oaxaca (Mexico); Bykov, A. [Institute for Problems of Materials Science of NASU, Kyiv (Ukraine); Leon, I. [CIQ-Universidad Autonoma del Estado de Morelos, Cuernavaca (Mexico); Siqueiros-Diaz, A. [FCQI-Universidad Autonoma del Estado de Morelos, Cuernavaca (Mexico)

2011-10-15

Experimental results of electron paramagnetic resonance spectra, X-ray diffraction, scanning electron microscopy and infrared spectroscopy demonstrate that the kinetic of the physical and chemical processes that takes place during prolonged intensive mechanical processing (MP, 03120min) of powder mixtures of 50%wt ZnO+50%wt MnO{sub 2} can be described as a three stage process. (1) 030min, particles destruction, formation of superficial defects, fast increment of sample average temperature (from 290 to {approx}600K) and annealing of defects with the lowest energy of activation E{sub ac}. (2) 30390min, further particle destruction, slow increment of sample average temperature (from {approx}600 to {approx}700K), formation and growth of a very disordered layer of {beta}-MnO{sub 2} around ZnO particles, dehydration of MnO{sub 2}, formation of solid solution of Mn{sup 2+} ions in ZnO, formation of nano-quasiamorphous states in the ZnO-MnO{sub 2} mixture and onset of the formation of the ZnMnO{sub 3} phase. (3) 3903120min, the sample average temperature remains constant ({approx}700K), the reaction is completed and the spinel ZnMnO{sub 3} phase with a unit cell a=8.431(1) A and space group Fd3-barm is the only phase present in the sample. No ferromagnetism at room temperature was detected in this study. - Highlights: > The kinetics during mechanical processing of ZnO-MnO{sub 2} samples is a three stage process. > First stage, reduction of crystallites size and accumulation of defects. > Second stage, nano-quasiamorphous states formation and onset of the ZnMnO{sub 3} phase. > Third stage, complete reaction to the spinel ZnMnO{sub 3} phase.

Excellent Brightness with Shortening Lifetime of Textured Zn2SiO4:Mn2+ Phosphor Films on Quartz Glass

Science.gov (United States)

Park, Jehong; Park, Kwangwon; Lee, Jaebum; Kim, Jongsu; Kim, Seongsin Margaret; Kung, Patrick

2010-04-01

Green-emissive textured Zn2SiO4:Mn2+ phosphor films were fabricated by the thermal diffusion of ZnO:Mn on quartz glass. The Zn2SiO4:Mn2+ phosphor films became textured along several hexagonal directions and their chemical composition was continuously graded at the interface. The decay time of Mn2+ was as short as 4.4 ms, and the optical transition probability of the films defined as the inverse of decay time showed a strong correlation with film texture degree as a function of annealing temperature. The brightest Zn2SiO4:Mn2+ film showed a photoluminescent brightness as high as 65% compared with a commercial Zn2SiO4:Mn2+ phosphor powder screen and a maximum absolute transparency of 70%. These excellent optical properties are explained by the combination of the unique textured structure and continuous grading of the Zn2SiO4:Mn2+ chemical composition at the interface.

Defect luminescence and lattice strain in Mn{sup 2+} doped ZnGa{sub 2}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Somasundaram, K.; Abhilash, K.P. [Department of Physics, Nallamuthu Gounder Mahalingam College, Pollachi, 642001 Coimbatore (India); Sudarsan, V., E-mail: vsudar@barc.gov.in [Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Christopher Selvin, P., E-mail: pcsphyngmc@rediffmail.com [Department of Physics, Nallamuthu Gounder Mahalingam College, Pollachi, 642001 Coimbatore (India); Kadam, R.M. [Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2016-06-15

Undoped and Mn{sup 2+} doped ZnGa{sub 2}O{sub 4} phosphors were prepared by solution combustion method and characterized by XRD, SEM, luminescence and electron paramagnetic resonance (EPR) techniques. Based on XRD results, it is inferred that, strain in ZnGa{sub 2}O{sub 4} host lattice increases with incorporation of Mn{sup 2+} ions in the lattice. Mn{sup 2+} doping at concentration levels investigated, lead to significant reduction in the defect emission and this has been attributed to the formation of higher oxidation states of Mn ions in the lattice. Electron Paramagnetic Resonance studies confirmed that majority of Mn ions exist as Mn{sup 2+} species and they occupy tetrahedral Zn{sup 2+} site in ZnGa{sub 2}O{sub 4} lattice with an average hyperfine coupling constant, A{sub iso}∼82 G.

Iron-based soft magnetic composites with Mn-Zn ferrite nanoparticles coating obtained by sol-gel method

Science.gov (United States)

Wu, Shen; Sun, Aizhi; Xu, Wenhuan; Zhang, Qian; Zhai, Fuqiang; Logan, Philip; Volinsky, Alex A.

2012-11-01

This paper focuses on iron-based soft magnetic composites which were synthesized by utilizing Mn-Zn ferrite nanoparticles to coat iron powder. The nanocrystalline iron powders, with an average particle diameter of 20 nm, were obtained via the sol-gel method. Scanning electron microscopy, energy dispersive X-ray spectroscopy and distribution maps show that the iron particle surface is covered with a thin layer of Mn-Zn ferrites. Mn-Zn ferrite uniformly coated the surface of the powder particles, resulting in a reduced imaginary permeability, increased electrical resistivity and a higher operating frequency of the synthesized magnets. Mn-Zn ferrite coated samples have higher permeability and lower magnetic loss when compared with the non-magnetic epoxy resin coated compacts. The real part of permeability increases by 33.5% when compared with the epoxy resin coated samples at 10 kHz. The effects of heat treatment temperature on crystalline phase formation and on the magnetic properties of the Mn-Zn ferrite were investigated via X-ray diffraction and a vibrating sample magnetometer. Ferrites decomposed to FeO and MnO after annealing above 400 °C in nitrogen; thus it is the optimum annealing temperature to attain the desired permeability.

Charge transport mechanisms and density of interface traps in MnZnO/p-Si diodes

International Nuclear Information System (INIS)

Taşçıoğlu, İlke; Farooq, W.A.; Turan, Raşit; Altındal, Şemsettin; Yakuphanoglu, Fahrettin

2014-01-01

Highlights: • The undoped and Mn doped ZnO films were deposited on p-Si substrates by sol–gel method. • The effect of Mn incorporation into ZnO on the electrical properties of ZnO/p-Si diodes were investigated. • The leakage current decreases and the rectification ratio increases with Mn doping. • The D it value was lowered by Mn dopant. -- Abstract: MnZnO films were grown onto p-Si substrate by sol–gel spin coating method. The electrical properties of the diodes were investigated at room temperature via the current–voltage (I–V), capacitance–voltage–frequency (C–V–f), and conductance—voltage–frequency (G–V–f) methods by considering the effect of the interface trap density (D it ) and series resistance (R s ) of the diodes. The rectifying ratio (RR) values of undoped and Mn-doped ZnO/p-Si diodes (at ±4 V) were found to be 275 and 2031, respectively. Mn doping decreases leakage current and increases shunt resistance (R sh ). Also, the reasons of discrepancies in barrier height values determined from different methods were discussed. The C–V and G–V measurements were performed at various frequencies. We observe additional contribution to the capacitance at low frequencies due to interface traps which can follow the ac test signal easily. The density of interface traps (D it ) determined from Hill–Coleman method was also presented for making comparison. The D it values vary from 9.24 × 10 11 to 1.67 × 10 13 eV −1 cm −2 and 2.06 × 10 11 to 2.54 × 10 12 eV −1 cm −2 for undoped and Mn-doped ZnO/p-Si diodes, respectively

Structural and magnetic Properties of Mn, Co, Ni doped ZnO ...

African Journals Online (AJOL)

It is abundant, cost effective, non-toxic and also it is used in many bio-medical applications. ... The XRD of Mn-doped ZnO nanocrystals shows hexagonal structure. ... The TM doped ZnO nanocrystals shows weak ferromagnetic properties at ...

Optical and magnetic resonance investigations of Zn1-x Mn x O magnetic semiconductors

International Nuclear Information System (INIS)

Zhang Huawei; Shi Erwei; Chen Zhizhan; Liu Xuechao; Xiao Bing; Song Lixin

2006-01-01

Zn 1- x Mn x O crystallites were synthesized by hydrothermal method. X-ray diffraction, UV-Vis absorption spectroscopy, and electron paramagnetic resonance (EPR) spectra confirm the substitution of Zn site by Mn 2+ ion. The nonmonotonic variation of band gap exhibits that the short-ranged interactions between the d electrons of Mn and the s and p electrons of the host bands are dominated at lower Mn concentration (x). EPR spectra show that Mn 2+ is in exchange interaction at higher x. By using a Curie-Weiss equation on the EPR data, it is found that the dominant magnetic property is antiferromagnetic for higher x, and paramagnetic for lower x

Facile hydrothermal synthesis of mn doped ZnO nanopencils for development of amperometric glucose biosensors

Science.gov (United States)

Shukla, Mayoorika; Pramila; Agrawal, Jitesh; Dixit, Tejendra; Palani, I. A.; Singh, Vipul

2018-05-01

Mn doped ZnO nanopencils were synthesized via low temperature hydrothermal process for fabrication of enzymatic electrochemical glucose biosensor. The KMnO4 was found to play a dual role in modifying morphology and inducing Mn doping. Interestingly, two different types of morphologies viz nanorods and nanopencils along with Mn doping in the later were obtained. Incorporation of Mn has shown a tremendous effect on the morphological variations, repression of defects and electrochemical charge transfer at electrode electrolyte interface. The possible reason behind obtained morphological changes has been proposed which in turn were responsible for the improvement in the different figure of merits of as fabricated enzymatic electrochemical biosensor. There has been a 17 fold enhancement in the sensitivity of the as fabricated glucose biosensor from ZnO nanorods to Mn doped ZnO nanopencils which can be attributed to morphological variation and Mn doping.

Structural, optical and electrical characterization of Mn2+ and Cd2+ doped/co-doped PbS nanocrystals

International Nuclear Information System (INIS)

Sakthi Sudar Saravanan, R.; Meena, M.; Pukazhselvan, D.; Mahadevan, C.K.

2015-01-01

Highlights: • Mn and Cd doped/codoped nano PbS was synthesized by SMI method. • The observed stress is ∼90% lower, and the strain is only in the order of 10 −6 . • Band gap value can be enhanced from 0.5 eV to 2.025–2.235 eV (±0.012 eV). • Role of two conduction activation barriers was observed. - Abstract: The strain and stress minimized nanoparticles of PbS, Pb 0.95 Mn 0.05 S, Pb 0.95 Cd 0.05 S and Pb 0.90 Mn 0.05 Cd 0.05 S were successfully synthesized using solvothermal microwave irradiation (SMI) method. The quality/performance of the materials was found to be in the series Pb 0.90 Mn 0.05 Cd 0.05 S > Pb 0.95 Cd 0.05 S > Pb 0.95 Mn 0.05 S > PbS. The average crystallite size in the best material Pb 0.90 Mn 0.05 Cd 0.05 S was found to be ∼18 nm where the particles are distributed within the range 20–60 nm. Optical studies reveals the existence of direct band gap in the range of 2.025–2.235 eV (±0.012 eV). This is one of the widest E g values reported for this system. Electrical measurements were performed on compacts of nanoparticles in the temperature range 313–433 K and frequency range 100 Hz–1 MHz. The conductivity profile exhibits two components; in which the activation energy (ΔE) values obtained for the temperature range 373–433 K is almost twice as compared to the ΔE value obtained for 313–373 K. Nonetheless, the conductivity at the higher temperatures was always higher than at the low temperatures and interestingly, the nanoparticles exhibits higher conductivity than their bulk counterpart. The feasible mechanism of conduction is discussed

Magnetic study of nanocrystalline 0.95MnO/0.05ZnO

International Nuclear Information System (INIS)

Guskos, N.; Dudek, M.; Zolnierkiewicz, G.; Typek, J.; Berczynski, P.; Lendzion-Bielun, Z.; Sibera, D.; Narkiewicz, U.

2013-01-01

Nanocrystalline 0.95MnO/0.05ZnO sample has been prepared by coprecipitation and calcination processes. X-ray diffraction showed the presence of Mn 3 O 4 nanocrystallites with an average size of 43 nm. Magnetic properties of the 0.95MnO/0.05ZnO sample have been investigated by dc magnetization and magnetic resonances (electron paramagnetic resonance (EPR), ferromagnetic resonance (FMR)) methods. The magnetization study has shown the presence of dominating Mn 3 O 4 paramagnetic and ferrimagnetic (below 46 K) phases. The blocking temperature determined from magnetization measurements was 41 K. An FMR study has shown the evidence of the spread of nanoparticles sizes. An EPR signal from paramagnetic phase of Mn 3 O 4 was observed at temperatures above 45 K and from defects/spurious phases in the low temperature range (T<16 K). Magnetic anisotropies of the sample in the FMR spectra were taken into account by fitting the observed spectra by two lines corresponding to parallel and perpendicular orientations of nanoparticles in an applied magnetic field. - Highlights: ► Magnetic properties of 0.95MnO/0.05ZnO have been studied by dc magnetization and magnetic resonance. ► FMR and EPR spectra were identified and attributed to various spin systems. ► From the spread of blocking temperatures obtained from magnetic resonance the spread of nanoparticles sizes was estimated.

Adsorption of Pb, Cd, Zn, Cu and Hg ions on Formaldehyde and ...

African Journals Online (AJOL)

Adsorption of Pb(II), Cd(II), Zn(II), Cu(II) and Hg(II) ions on formaldehyde and Pyridine modified bean husks were determined. The adsorption capacity of formaldehyde modified bean husks (mg/g) was: Pb2+, 5.01; Cd2+, 3.63; Zn2+, 2.18; Hg2+, 1.82; Cu2+, 1.58 and that of pyridine modified bean husk was: Hg2+, 6.92; Cd2+ ...

Impacts of MnZn doping on the structural and magnetic properties of M-type SrCaLa hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Yang, Yujie; Shao, Juxiang; Wang, Fanhou; Huang, Duohui [Yibin University, Computational Physics Key Laboratory of Sichuan Province, School of Physics and Electronic Engineering, Yibin (China); Liu, Xiansong [Anhui University, Engineering Technology Research Center of Magnetic Materials, Anhui Province, School of Physics and Materials Science, Hefei (China)

2017-05-15

M-type hexaferrites with chemical compositions of Sr{sub 0.5}Ca{sub 0.2}La{sub 0.3}Fe{sub 12.0-2x} (MnZn){sub x} O{sub 19} (0.0 ≤ x ≤ 0.5) were synthesized by the traditional ceramic method. The crystal structure of M-type hexaferrite samples was examined by X-ray diffraction. The structural analyses reveal that all samples are in single M-type hexagonal phase and no secondary phase is present. A physical property measurement system-vibrating sample magnetometer was used to measure the magnetic properties of M-type hexaferrite samples. The saturation magnetization (M{sub s}), remanent magnetization (M{sub r}) and coercivity (H{sub c}) were calculated from magnetic hysteresis loops. M{sub s} first increases with MnZn content (x) from 0.0 to 0.1, and then decreases with MnZn content (x) from 0.1 to 0.5. While, M{sub r} decreases with MnZn content (x) from 0.0 to 0.2, and then increases with MnZn content (x) from 0.2 to 0.5. H{sub c} first decreases with MnZn content (x) from 0.0 to 0.2, and then increase with MnZn content (x) from 0.2 to 0.5. (orig.)

Characteristic of total suspended particulate (TSP) containing Pb and Zn at solid waste landfill

Science.gov (United States)

Budihardjo, M. A.; Noveandra, K.; Samadikun, B. P.

2018-05-01

Activities conducted at municipal solid waste landfills (MSWLs) potentially cause air pollution. Heavy vehicles in MSWLs release various pollutants that can have negative impacts for humans. One noticeable pollutant at MSWLs is airborne total suspended particulate (TSP) which may contain heavy metals such as Pb and Zn and can cause disease when inhaled by humans. In this study, TSP from a landfill in Semarang, Indonesia was collected and characterized to quantify the concentration of Pb and Zn. Meteorological factors (i.e. temperature, humidity and wind velocity) and landfill activities were considered as factors affecting pollutant concentrations. TSP was sampled using dust samplers while the concentrations of heavy metals in TSP were analyzed using an Atomic Absorption Spectrophotometer (AAS). Pb concentration ranged from 0.84 to 1.78 µg/m3 while Zn concentration was from 7.87 to 8.76 µg/m3. The levels of Pb were below the threshold specified by the Indonesian Government. Meanwhile, the threshold for Zn has not yet been determined.

First principles density functional theory study of Pb doped α-MnO2 catalytic materials

Science.gov (United States)

Song, Zilin; Yan, Zhiguo; Yang, Xiaojun; Bai, Hang; Duan, Yuhua; Yang, Bin; Leng, Li

2018-03-01

The impact of Pb in the tunnels of manganese oxide octahedral molecular sieves on chemical state of Mn species and lattice oxygen were investigated utilizing density functional theory calculations. The results show that the Pb dopant in the tunnels of OMS-2 could reduce the average valence states of Mn. The lower energy required for bulk oxygen defects formation in Pb-OMS-2 validates the activation of lattice oxygen by inclusion of tunnel dopant. The inclusion of Pb promotes the catalytic oxidation activity of OMS-2 by reducing the energy required for the surface lattice oxygen migration during the Mars - van Krevelen oxidation process.

Physical properties of antiferromagnetic Mn doped ZnO samples: Role of impurity phase

Science.gov (United States)

Neogi, S. K.; Karmakar, R.; Misra, A. K.; Banerjee, A.; Das, D.; Bandyopadhyay, S.

2013-11-01

Structural, morphological, optical, and magnetic properties of nanocrystalline Zn1-xMnxO samples (x=0.01, 0.02, 0.04, 0.06, 0.08 and 0.10) prepared by the sol-gel route are studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV-visible absorption spectroscopy, Superconducting quantum interference device (SQUID) magnetometry and positron annihilation lifetime spectroscopy (PALS). XRD confirms formation of wurzite structure in all the Mn-substituted samples. A systematic increase in lattice constants and decrease in grain size have been observed with increase in manganese doping concentration up to 6 at% in the ZnO structure. An impurity phase (ZnMnO3) has been detected when percentage of Mn concentration is 6 at% or higher. The optical band gap of the Mn-substituted ZnO samples decrease with increase in doping concentration of manganese whereas the width of the localized states increases. The antiferromagnetic exchange interaction is strong in the samples for 2 and 4 at% of Mn doping but it reduces when the doping level increases from 6 at% and further. Positron life time components τ1 and τ2 are found to decrease when concentration of the dopant exceeds 6 at%. The changes in magnetic properties as well as positron annihilation parameters at higher manganese concentration have been assigned as due to the formation of impurity phase. Single phase structure has been observed up to 6 at% of Mn doping. Impurity phase has been developed above 6 at% of Mn doping. Antiferromagnetic and paramagnetic interactions are present in the samples. Defect parameters show sharp fall as Mn concentration above 6 at%. The magnetic and defect properties are modified by the formation of impurity phase.

Bismuth zinc vanadate, BiZn2VO6: New crystal structure type and electronic structure

International Nuclear Information System (INIS)

Eliziario Nunes, Sayonara; Wang, Chun-Hai; So, Karwei; Evans, John S.O.; Evans, Ivana Radosavljević

2015-01-01

We report a combined experimental and computational study of the crystal structure and electronic properties of bismuth zinc vanadate, BiZn 2 VO 6 , known for its visible light photocatalytic activity. The crystal structure has been solved from laboratory powder X-ray diffraction data using the repeated minimisations from random starting values method. BiZn 2 VO 6 adopts a new structure type, based on the following building blocks: corner- and edge-sharing ZnO 4 tetrahedra, ZnO 6 octahedra and VO 4 tetrahedra, and Bi 2 O 12 dimers. It is the only known member of the BiM 2 AO 6 (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family which does not appear to be structurally closely related to others. The electronic structure of BiZn 2 VO 6 , calculated by DFT methods, shows that it is an indirect gap semiconductor with a calculated band gap of 1.6 eV, which compares favourably to the experimentally measured value of 2.4 eV. - Graphical abstract: The crystal structure of BiZn 2 VO 6 , a new structure type in the BiM 2 AO 6 (M=Mg, Ca, Cd, Cu, Pb, Mn, Zn; A=V, P, As) family. - Highlights: • Structure solution from PXRD data by repeated minimisations from random starting values. • New structure type in the BiM 2 AO 6 (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family. • Electronic structure calculation

Effect of 50 MeV Li3+ irradiation on structural and electrical properties of Mn-doped ZnO

International Nuclear Information System (INIS)

Neogi, S K; Chattopadhyay, S; Banerjee, Aritra; Bandyopadhyay, S; Sarkar, A; Kumar, Ravi

2011-01-01

The present work aims to study the effect of ion irradiation on structural and electrical properties and their correlation with the defects in the Zn 1-x Mn x O-type system. Zn 1-x Mn x O (x = 0.02, 0.04) samples have been synthesized by the solid-state reaction method and have been irradiated with 50 MeV Li 3+ ions. The concomitant changes have been probed by x-ray diffraction (XRD), temperature-dependent electrical resistivity and positron annihilation lifetime (PAL) spectroscopy. The XRD result shows a single-phase wurtzite structure for Zn 0.98 Mn 0.02 O, whereas for the Zn 0.96 Mn 0.04 O sample an impurity phase has been found, apart from the usual peaks of ZnO. Ion irradiation removes this impurity peak. The grain size of the samples is found to be uniform. For Zn 0.98 Mn 0.02 O, the observed sharp decrease in room temperature resistivity (ρ RT ) with irradiation is consistent with the lowering of the full width at half maximum of the XRD peaks. However, for Zn 0.96 Mn 0.04 O, ρ RT decreases for the initial fluence but increases for a further increase in fluence. All the irradiated Zn 0.98 Mn 0.02 O samples show a metal-semiconductor transition in temperature-dependent resistivity measurements at low temperature. But all the irradiated Zn 0.96 Mn 0.04 O samples show a semiconducting nature in the whole range of temperatures. Results of room temperature resistivity, XRD and PAL measurements are consistent with each other.

Magnetic susceptibility of MnZn and NiZn soft ferrites using Laplace transform and the Routh-Hurwitz criterion

International Nuclear Information System (INIS)

Fano, Walter Gustavo; Boggi, Silvina; Razzitte, Adrian Cesar

2011-01-01

This paper is devoted to study the Routh-Hurwitz stability criterion from the MnZn and NiZn soft ferrites using a phenomenological model with the gyromagnetic spin contribution and domain wall contribution. The magnetodynamic equation and the harmonic oscillator equation have been used to obtain the domain walls and the spin contribution of the magnetic susceptibility. The ferrite materials have been considered as linear, time invariant, isotropic and homogeneous, and the magnetization vector is proportional to the magnetic field vector. The resulting expression of the magnetization in time domain of both ferrites under study has been obtained by mean of the inverse Laplace transformation applying the residue method. The poles of the magnetic susceptibility have negative real parts, which ensures that the response decays exponentially to zero as the time increase. The degree of the numerator's polynomial of the magnetic susceptibility is less than the degree of denominator's polynomial in the magnetic susceptibility function: and the poles are located in the half left s-plane. Then the system is bounded-input, bounded-output (BIBO), and the results agree with the Routh-Hurwitz stability criterion for the MnZn and NiZn soft ferrites. - Research Highlights: → Laplace transform of the magnetic susceptibility of the MnZn and NiZn soft ferrites. → Routh-Hurwitz stability criterion of magnetic materials. → Bode plot of magnetic susceptibility. → Inverse Laplace transform using residue theorem.

Tolerance of Portulaca grandiflora to individual and combined application of Ni, Pb and Zn.

Science.gov (United States)

Mihailovic, N; Andrejić, G; Dželetović, Ž

2015-01-01

In the present study, metal accumulation capacity and tolerance of Portulaca grandiflora were investigated. Plants were grown under greenhouse conditions in pots on soil amended with Ni, Pb and Zn to the final concentration of 2 mmol kg(-1) for each metal. Results show considerable accumulating capacity and translocation of Ni and Zn, as well as significant accumulation of Pb in roots. A slight decrease of biomass with Zn and of chlorophyll content with Zn and Ni were observed, as well as an increase of proline content with each of the metals. Combinations of metals revealed mutual interference affecting both the uptake and translocation of the metals and their impact on physiological parameters. Results suggest that Portulaca grandiflora, although not a hyperaccumulator, shows a good tolerance and accumulation capacity for Ni, Pb and Zn, but, for the purposes of remediation, interference of the metals must be taken into account.

Thermodynamics of Pb(ii) and Zn(ii) binding to MT-3, a neurologically important metallothionein.

Science.gov (United States)

Carpenter, M C; Shami Shah, A; DeSilva, S; Gleaton, A; Su, A; Goundie, B; Croteau, M L; Stevenson, M J; Wilcox, D E; Austin, R N

2016-06-01

Isothermal titration calorimetry (ITC) was used to quantify the thermodynamics of Pb(2+) and Zn(2+) binding to metallothionein-3 (MT-3). Pb(2+) binds to zinc-replete Zn7MT-3 displacing each zinc ion with a similar change in free energy (ΔG) and enthalpy (ΔH). EDTA chelation measurements of Zn7MT-3 and Pb7MT-3 reveal that both metal ions are extracted in a tri-phasic process, indicating that they bind to the protein in three populations with different binding thermodynamics. Metal binding is entropically favoured, with an enthalpic penalty that reflects the enthalpic cost of cysteine deprotonation accompanying thiolate ligation of the metal ions. These data indicate that Pb(2+) binding to both apo MT-3 and Zn7MT-3 is thermodynamically favourable, and implicate MT-3 in neuronal lead biochemistry.

Magnetic properties and loss separation in FeSi/MnZnFe{sub 2}O{sub 4} soft magnetic composites

Energy Technology Data Exchange (ETDEWEB)

Lauda, M. [Institute of Physics, Faculty of Science, Pavol Jozef Šafárik Univesity, Park Angelinum 9, 04154 Košice (Slovakia); Füzer, J., E-mail: jan.fuzer@upjs.sk [Institute of Physics, Faculty of Science, Pavol Jozef Šafárik Univesity, Park Angelinum 9, 04154 Košice (Slovakia); Kollár, P. [Institute of Physics, Faculty of Science, Pavol Jozef Šafárik Univesity, Park Angelinum 9, 04154 Košice (Slovakia); Strečková, M.; Bureš, R. [Institute of Materials Research, Slovak Academy of Sciences, Watsonova 47, 04001 Košice (Slovakia); Kováč, J.; Baťková, M.; Baťko, I. [Institute of Experimental Physics, Slovak Academy of Sciences, Watsonova 47, 04001 Košice (Slovakia)

2016-08-01

We investigated composites that have been prepared from FeSi powders covered with MnZnFe{sub 2}O{sub 4} (MnZn ferrite), which was prepared by sol–gel synthesis accompanied with the auto-combustion process. The aim of this paper is to analyze the complex permeability and core losses of prepared samples with different amount of MnZn ferrite. The microstructure and the powder morphology were examined by scanning electron microscopy. Magnetic measurements on bulk samples were carried out using a vibrating sample magnetometer, an impedance analyzer and hysteresisgraphs. The results indicate that the composites with 2.6 wt% MnZn ferrite show better soft magnetic properties than the composites with about 6 wt% MnZn ferrite. - Highlights: • Successful preparation of soft magnetic composite FeSi/MnZnFe{sub 2}O{sub 4}. • Study of the complex magnetic permeability. • Comparison of different compositions of prepared SMC's. • Determination of parts of magnetic losses.

Elastocaloric effect in CuAlZn and CuAlMn shape memory alloys under compression

OpenAIRE

Qian, Suxin; Geng, Yunlong; Wang, Yi; Pillsbury, Thomas E.; Hada, Yoshiharu; Yamaguchi, Yuki; Fujimoto, Kenjiro; Hwang, Yunho; Radermacher, Reinhard; Cui, Jun; Yuki, Yoji; Toyotake, Koutaro; Takeuchi, Ichiro

2016-01-01

This paper reports the elastocaloric effect of two Cu-based shape memory alloys: Cu68Al16Zn16 (CuAlZn) and Cu73Al15Mn12 (CuAlMn), under compression at ambient temperature. The compression tests were conducted at two different rates to approach isothermal and adiabatic conditions. Upon unloading at a strain rate of 0.1 s−1 (adiabatic condition) from 4% strain, the highest adiabatic temperature changes (ΔTad) of 4.0 K for CuAlZn and 3.9 K for CuAlMn were obtained. The maximum stress and hystere...

Far-infrared phonon spectroscopy of Pb1-xMn xTe layers grown by molecular beam epitaxy

International Nuclear Information System (INIS)

Romcevic, N.; Nadolny, A.J.; Romcevic, M.; Story, T.; Taliashvili, B.; Milutinovic, A.; Trajic, J.; Lusakowska, E.; Vasiljevic-Radovic, D.; Domukhovski, V.; Osinniy, V.; Hadzic, B.; Dziawa, P.

2007-01-01

In this paper we used far-infrared spectroscopy, reflection high energy electron diffraction (RHEED), X-ray diffraction and atomic force microscopy (AFM) to investigate structural and optical properties of Pb 1-x Mn x Te layers grown by molecular beam epitaxy (MBE). A numerical model for calculating the reflectivity coefficient for complex systems which include films, buffer layer and substrate has been applied. The infrared reflectivity spectra consist of Pb 1-x Mn x Te phonons, which exhibit intermediate one-two mode behavior, and MnTe phonons. A good agreement between calculated and experimental spectra is achieved. We registered the local distribution of Mn impurities depending on substrate type. For films growth on BaF 2 substrate we registered the orthorhombic local structure of MnTe clusters, while in the case of KCl substrate this structure is cubic. The Pb 1-x Mn x Te long wavelength optical phonons were described by the modified Genzel's model

Discovery of Wolitu Pb-Zn deposit through geochemical prospecting under loess cover in Inner Mongolia, China

Directory of Open Access Journals (Sweden)

Fan Yang

2017-09-01

Full Text Available We report the finding of the Wolitu Pb-Zn deposit in Inner Mongolia, China, through a series of geochemical surveys. The Wolitu area, located in the loess-cover area in the Hure Banner, Tongliao City, Inner Mongolia, and neighboring the Horqin Sandy Land to the north, had no previous history of Pb-Zn mining or record of Pb-Zn mineralization. Our study identified a large Pb-Zn anomaly with potential zones of mineralization by stream sediment survey. Random rock sampling reveals limonitization at sporadic outcrops in the gullies. The high concentrations of Pb in the residual debris provided guidelines to fix the position for exploratory trench. Oxidized concealed orebodies were identified by trenching. Blind orebodies in veins hosted within the structural zone between slates and marbles of the upper Carboniferous Shizuizi Formation and the Permian granite were discovered by drilling. It is computed that the ore reserve may reach up to 540,000 tones with Pb grade of 1.27% and Zn of 1.9%. This case study is an excellent example for identifying potential polymetallic deposits in loess covered terrains using geochemical exploration.

Adsorption of Cu, As, Pb and Zn by Banana Trunk

International Nuclear Information System (INIS)

Nurzulaifa Shaheera Erne Mohd Yasim; Zitty Sarah Ismail; Suhanom Mohd Zaki; Mohd Fahmi Abd Azis

2016-01-01

The purpose of this study is to investigate the effectiveness of banana trunk as an adsorbent in removal of heavy metals in aqueous solution. Functional groups of adsorbent were determined using Fourier Transform Infrared spectroscopy (FTIR). Batch experiments were conducted to determine the adsorption percentage of heavy metals (Cu, As, Pb and Zn). The optimum adsorption using banana trunk was based on pH difference, contact time and dosage. Adsorption percentage was found to be proportional to pH, contact time and dosage. Maximum adsorption percentage of Cu, As, Pb and Zn at pH 6, 100 minutes and 8 gram of dosage are 95.80 %, 75.40 %, 99.36 % and 97.24 %, respectively. Langmuir and Freundlich isotherms were used to determine the equilibrium state for heavy metals ion adsorption experiments. All equilibrium heavy metals were well explained by the Freundlich isotherm model with R"2= 0.9441, R"2= 0.8671, R"2= 0.9489 and R"2= 0.9375 for Cu, As, Pb and Zn respectively. It is concluded that banana trunk has considerable potential for the removal of heavy metals from aqueous solution. (author)

Synthesis and characterization of sol–gel derived ZnS : Mn ...

Indian Academy of Sciences (India)

Unknown

The films were then (in less than ~ 10 s) transferred to an oven preset at the ... (5 at.%) nanocrystalline ZnS film. Figure 3. d{ln(αhν)}/d(hν) vs hν plots for (a) undoped and. (b) Mn2+ doped nanocrystalline ZnS film (α in cm–1, hν in eV). Figure 1. .... 2⋅8 nm and 2⋅12 nm in case of undoped and doped ZnS nanocrystalline ...

Thermal analysis and prediction of phase equilibria in ternary Pb-Zn-Ag system

Directory of Open Access Journals (Sweden)

Živković D.

2011-01-01

Full Text Available Ternary Pb-Zn-Ag system is typical for some physicochemical processes going on in refining phase in the extractive metallurgy of lead. Therefore, investigation of mentioned system is important from both theoretical and practical research of the phenomena occurring during the lead desilverizing process. The results of experimental investigation using differential thermal analysis (DTA and thermodynamic calculation of phase equilibria in Pb-Zn-Ag system according to CALPHAD method, in the sections with Zn:Ag mass ratio equal to 90:10, 70:30 and 50:50, are presented in this paper.

ZnO@MnO2 Core-Shell Nanofiber Cathodes for High Performance Asymmetric Supercapacitors.

Science.gov (United States)

Radhamani, A V; Shareef, K M; Rao, M S Ramachandra

2016-11-09

Asymmetric supercapacitors (ASCs) with aqueous electrolyte medium have recently become the focus of increasing research. For high performance ASCs, selection of cathode materials play a crucial role, and core-shell nanostructures are found to be a good choice. We successfully synthesized, ZnO@MnO 2 core-shell nanofibers (NFs) by modification of high-aspect-ratio-electrospun ZnO NFs hydrothermally with MnO 2 nanoflakes. High conductivity of the ZnO NFs and the exceptionally high pseudocapacitive nature of MnO 2 nanoflakes coating delivered a specific capacitance of 907 Fg -1 at 0.6 Ag -1 for the core-shell NFs. A simple and cost-effective ASC construction was demonstrated with ZnO@MnO 2 NFs as a battery-type cathode material and a commercial-quality activated carbon as a capacitor-type anode material. The fabricated device functioned very well in a voltage window of 0-2.0 V, and a red-LED was illuminated using a single-celled fabricated ASC device. It was found to deliver a maximum energy density of 17 Whkg -1 and a power density of 6.5 kWkg -1 with capacitance retention of 94% and Coulombic efficiency of 100%. The novel architecture of the ZnO@MnO 2 core-shell nanofibrous material implies the importance of using simple design of fiber-based electrode material by mere changes of core and shell counterparts.

Structural and Magnetic Properties of Mn doped ZnO Thin Film Deposited by Pulsed Laser Deposition

KAUST Repository

Baras, Abdulaziz

2011-07-01

Diluted magnetic oxide (DMO) research is a growing field of interdisciplinary study like spintronic devices and medical imaging. A definite agreement among researchers concerning the origin of ferromagnetism in DMO has yet to be reached. This thesis presents a study on the structural and magnetic properties of DMO thin films. It attempts to contribute to the understanding of ferromagnetism (FM) origin in DMO. Pure ZnO and Mn doped ZnO thin films have been deposited by pulsed laser deposition (PLD) using different deposition conditions. This was conducted in order to correlate the change between structural and magnetic properties. Structural properties of the films were characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM). The superconducting quantum interference device (SQUID) was used to investigate the magnetic properties of these films. The structural characterizations showed that the quality of pure ZnO and Mn doped ZnO films increased as oxygen pressure (PO) increased during deposition. All samples were insulators. In Mn doped films, Mn concentration decreased as PO increased. The Mn doped ZnO samples were deposited at 600˚C and oxygen pressure from 50-500mTorr. All Mn doped films displayed room temperature ferromagnetism (RTFM). However, at 5 K a superparamagnetic (SPM) behavior was observed in these samples. This result was accounted for by the supposition that there were secondary phase(s) causing the superparamagnetic behavior. Our findings hope to strengthen existing research on DMO origins and suggest that secondary phases are the core components that suppress the ferromagnetism. Although RTFM and SPM at low temperature has been observed in other systems (e.g., Co doped ZnO), we are the first to report this behavior in Mn doped ZnO. Future research might extend the characterization and exploration of ferromagnetism in this system.

Concentrations of Se, Ba, Zn and Mn in Brazil nuts

Energy Technology Data Exchange (ETDEWEB)

Armelin, Maria José A.; Maihara, Vera A.; Cardoso, Paulo S.; Saiki, Mitiko [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Cozollino, Silvia M.F., E-mail: marmelin@ipen.br, E-mail: vmaihara@ipen.br, E-mail: msaiki@ipen.br, E-mail: pscsilva@ipen.br, E-mail: smfcozzo@usp.br [Universidade de São Paulo (USP), SP (Brazil). Faculdade de Ciências Farmacêuticas

2017-07-01

The concentrations of Se, Ba, Zn and Mn were determined in samples of Brazil nuts collected in two ways: a) in a production farm predominantly for export and, b) in various points of sale from different regions of Brazil. Instrumental neutron activation analysis was the analytical technique used in this study. Results indicate that the concentrations of Se and Ba varied greatly among the Brazil nut samples analyzed. This large variability may be related to the soil characteristics from which the nuts were produced. An inverse correlation was observed between the concentrations of Se and Ba. On the other hand, the concentrations of Zn and Mn did not show significant differences among these samples. (author)

Concentrations of Se, Ba, Zn and Mn in Brazil nuts

International Nuclear Information System (INIS)

Armelin, Maria José A.; Maihara, Vera A.; Cardoso, Paulo S.; Saiki, Mitiko; Cozollino, Silvia M.F.

2017-01-01

The concentrations of Se, Ba, Zn and Mn were determined in samples of Brazil nuts collected in two ways: a) in a production farm predominantly for export and, b) in various points of sale from different regions of Brazil. Instrumental neutron activation analysis was the analytical technique used in this study. Results indicate that the concentrations of Se and Ba varied greatly among the Brazil nut samples analyzed. This large variability may be related to the soil characteristics from which the nuts were produced. An inverse correlation was observed between the concentrations of Se and Ba. On the other hand, the concentrations of Zn and Mn did not show significant differences among these samples. (author)

Effect of Cu(II), Cd(II) and Zn(II) on Pb(II) biosorption by algae Gelidium-derived materials.

Science.gov (United States)

Vilar, Vítor J P; Botelho, Cidália M S; Boaventura, Rui A R

2008-06-15

Biosorption of Pb(II), Cu(II), Cd(II) and Zn(II) from binary metal solutions onto the algae Gelidium sesquipedale, an algal industrial waste and a waste-based composite material was investigated at pH 5.3, in a batch system. Binary Pb(II)/Cu(II), Pb(II)/Cd(II) and Pb(II)/Zn(II) solutions have been tested. For the same equilibrium concentrations of both metal ions (1 mmol l(-1)), approximately 66, 85 and 86% of the total uptake capacity of the biosorbents is taken by lead ions in the systems Pb(II)/Cu(II), Pb(II)/Cd(II) and Pb(II)/Zn(II), respectively. Two-metal results were fitted to a discrete and a continuous model, showing the inhibition of the primary metal biosorption by the co-cation. The model parameters suggest that Cd(II) and Zn(II) have the same decreasing effect on the Pb(II) uptake capacity. The uptake of Pb(II) was highly sensitive to the presence of Cu(II). From the discrete model it was possible to obtain the Langmuir affinity constant for Pb(II) biosorption. The presence of the co-cations decreases the apparent affinity of Pb(II). The experimental results were successfully fitted by the continuous model, at different pH values, for each biosorbent. The following sequence for the equilibrium affinity constants was found: Pb>Cu>Cd approximately Zn.

Detection of DNA via the fluorescence quenching of Mn-doped ZnSe D-dots/doxorubicin/DNA ternary complexes system.

Science.gov (United States)

Gao, Xue; Niu, Lu; Su, Xingguang

2012-01-01

This manuscript reports a method for the detection of double-stranded DNA, based on Mn:ZnSe d-dots and intercalating agent doxorubicin (DOX). DOX can quench the photoluminescence (PL) of Mn:ZnSe d-dots through photoinduced electron transfer process, after binding with Mn:ZnSe d-dots. The addition of DNA can result in the formation of the Mn:ZnSe d-dots-DOX-DNA ternary complexes, the fluorescence of the Mn:ZnSe d-dots-DOX complexes would be further quenched by the addition of DNA, thus allowing the detection of DNA. The formation mechanism of the Mn:ZnSe d-dots-DOX-DNA ternary complexes was studied in detail in this paper. Under optimal conditions, the quenched fluorescence intensity of Mn:ZnSe d-dots-DOX system are perfectly described by Stern-Volmer equation with the concentration of hsDNA ranging from 0.006 μg mL(-1) to 6.4 μg mL(-1). The detection limit (S/N = 3) for hsDNA is 0.5 ng mL(-1). The proposed method was successfully applied to the detection of DNA in synthetic samples and the results were satisfactory.

Synthesis and electrochemical performances of ZnO/MnO2 sea urchin-like sleeve array as anode materials for lithium-ion batteries

International Nuclear Information System (INIS)

Fang, J.; Yuan, Y.F.; Wang, L.K.; Ni, H.L.; Zhu, H.L.; Yang, J.L.; Gui, J.S.; Chen, Y.B.; Guo, S.Y.

2013-01-01

MnO 2 is electrodeposited onto ZnO nanorod array grown on Ni foil, forming a binder-free ZnO/MnO 2 composited electrode. XRD, EDS, SEM and TEM are used to analyze the phase and microstructure of this composite. Burr-like MnO 2 nanoflakes grows on ZnO nanorod array, the top of the composite is hollow and at the bottom exists ZnO large block core as an internal support, forming ZnO/MnO 2 sea urchin-like sleeve array. As anode material for lithium ion batteries, ZnO/MnO 2 sleeve array exhibits higher discharge capacity and coulombic efficiency, better rate performance and cycling stability than single ZnO nanorod array or directly electrodepsited MnO 2 , and the composite effect is very remarkable. After 100 cycles, the discharge capacity of ZnO/MnO 2 still reaches 1259 mA h g −1 , and coulombic efficiency surpasses 98%, higher than those of ZnO nanorod array (111 mA h g −1 ) and directly electrodeposited MnO 2 (507 mA h g −1 ). The improvement of the electrochemical performances is due to the unique sea urchin-like sleeve array architecture. MnO 2 burr tube shell structure leads to high electrochemical activity while the internal ZnO core support ensures good structure stability. The gradually opening of sea urchin-like sleeve during the cycling further enhances the electrochemical activity of MnO 2 , stabilizing and increasing electrochemical performances of the ZnO/MnO 2 composite

Application of Zn isotopes in environmental impact assessment of Zn–Pb metallurgical industries: A mini review

International Nuclear Information System (INIS)

Yin, Nang-Htay; Sivry, Yann; Benedetti, Marc F.; Lens, Piet N.L.; Hullebusch, Eric D. van

2016-01-01

Zn and Pb smelters are the major contributors to Zn and Pb emissions among all anthropogenic sources, thus, it is essential to understand Zn isotopic variations within the context of metallurgical industries, as well as its fractionation in different environments impacted by smelting activities. This mini review outlines the current state of knowledge on Zn isotopic fractionation during the high-temperature roasting process in Zn and Pb refineries; δ"6"6Zn values variations in air emissions, slags and effluents from the smelters in comparison to the geogenic Zn isotopic signature of ores formation and weathering. In order to assess the environmental impact of these smelters, the available and measured δ"6"6Zn values are compiled for smelter impacted natural water bodies (groundwater, stream and river water), sediments (lake and reservoir) and soils (peat bog soil, inland soil). Finally, the discussion is extended to the fractionation induced during numerous physicochemical reactions and transformations, i.e. adsorption, precipitation as well as both inorganic and organic surface complexation. - Highlights: • Zn and Pb smelters are the major contributors to Zn emissions among all anthropogenic sources. • Zn isotopic variations in this context has been widely studied over the last 15 years. • Zn isotopic fractionation during the high-temperature roasting process and electroplating process is summarize. • Subsequent δ"6"6Zn values variations in air emissions, slags and effluents from the smelters are compared to the geogenic one. • The usefulness of δ"6"6Zn values to trace environmental impact of these smelters is discussed.

Use of ZnO:Mn particles for degradation of methylene blue by photocatalysis process; Utilizacao de particulas de ZnO:Mn para a degradacao do azul de metileno por processo de fotocatalise

Energy Technology Data Exchange (ETDEWEB)

Giraldi, T. R.; Swerts, J. P.; Vicente, M. A., E-mail: tania.giraldi@unifal-mg.edu.br, E-mail: jefersonps21@hotmail.com, E-mail: maquelyaspr@oi.com.br [Universidade Federal de Alfenas (UNIFAL), Pocos de Caldas, MG (Brazil). Instituto de Ciencia e Tecnologia; Mendonca, V.R. de, E-mail: vrm@ifsp.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia de Sao Paulo (IFSP), Itapetininga, SP (Brazil); Paris, E.C.; Ribeiro, C., E-mail: elaine.paris@embrapa.br, E-mail: caue.ribeiro@embrapa.br [Embrapa Instrumentacao, Sao Carlos, SP (Brazil)

2016-10-15

The management of water use in the agricultural environment is a key factor to build new environmentally sustainable productive methods. Photocatalysis is a promising method for water decontamination. This research paper aimed to evaluate the photocatalytic potential of pure and Mn-doped ZnO particles. The materials were obtained by the polymeric precursor method, and characterized by X-ray diffraction, N{sub 2} adsorption in low temperature, infrared and ultraviolet spectroscopy, and photoluminescence. In order to evaluate ZnO:Mn particles photo efficiency, experiments were carried out by applying the methylene blue dye solution to photodegradation under UVC exposure. The particles had ZnO single-phase, but low specific surface area. The sample ZnO:0.25% Mn presented higher efficiency in the methylene blue photocatalytic degradation test. This efficiency was related to a higher band gap energy value and a lower rate of electron recombination, which allows greater formation of hydroxyl radicals, which are responsible for dye degradation. (author)

Long afterglow properties of Eu2+/Mn2+ doped Zn2GeO4

International Nuclear Information System (INIS)

Wan, Minhua; Wang, Yinhai; Wang, Xiansheng; Zhao, Hui; Li, Hailing; Wang, Cheng

2014-01-01

Zn 2 GeO 4 :Eu 2+ 0.01 and Zn 2 GeO 4 :Mn 2+ 0.01 long afterglow phosphors were synthesized via a high temperature solid state reaction. X-ray diffraction (XRD), afterglow spectra, decay curves and thermoluminescence curves were utilized to characterize the samples. The X-ray diffraction phases indicate that the doping of small amount of transition metal ions or rare earth ions has no significant influence on the crystal structure of Zn 2 GeO 4 . According to the afterglow spectra, we found that the Zn 2 GeO 4 :Eu 2+ 0.01 exhibits a broad band emission with a peak at 474 nm, which could be ascribed to Eu 2+ transition between 4f 6 5d 1 and 4f 7 electron configurations. The Zn 2 GeO 4 :Mn 2+ 0.01 shows a narrow band emission peaking at 532 nm corresponding to the characteristic transition of Mn 2+ ( 4 T 1 → 6 A 1 ). The thermoluminescence (TL) curves above room temperature are employed for the discussion of the origin of the traps and the mechanism of the persistent luminescence. The results indicate that Zn 2 GeO 4 may be an excellent host material for the rare earth ions or transition metal ions long afterglows. -- Highlights: • Zn 2 GeO 4 :Eu 2+ 0.01 and Zn 2 GeO 4 :Mn 2+ 0.01 long afterglow phosphors were synthesized. • Found that these phosphors possess a persistent luminescence property. • The long afterglow spectra were measured. • Found that these phosphors possess a trap level by thermoluminescence

Synthesis and Optical Properties of MnS–ZnS and MnS–CdS Nanoparticles in Montmorillonite.

Science.gov (United States)

Kabilaphat, Jirabhorn; Poosimma, Poonsuk; Khaorapapong, Nithima; Intachai, Sonchai; Ogawa, Makoto

2017-02-01

The incorporation of metal sulfide mixture, manganese sulfide and zinc sulfide (MnS–ZnS) or manganese sulfide and cadmium sulfide (MnS–CdS), in two types of montmorillonites (sodium montmorillonite and cetyltrimethylammonium modified montmorillonite) was investigated. The hybrids were characterized by powder X-ray diffraction, thermogravimetric-differential thermal analysis, transmission electron microscopy (TEM), and Raman, UV-visible and photoluminescence spectroscopies. The experimental evidences such as the expansion of the interlayer spaces and the presence of the absorption and photoluminescence due to MnS, ZnS and/or CdS revealed that the mixed metal sulfides formed in the interlayer space of montmorillonites. TEM images of the hybrids showed diskor plate-shaped nanoparticles with a mean diameter of ca. 2 nm. The increase of the luminescence intensities of the hybrids was assumed to be caused by quantum confinement effect in the interlayer space of montmorillonite.

Quantitative trait loci controlling Cu, Ca, Zn, Mn and Fe content in ...

Indian Academy of Sciences (India)

of essential minerals (such as Fe, Zn etc), breeding mineral- efficient crops that produce .... and seven digenic interactions were identified for Cu, Ca,. Zn, Mn and Fe, .... Eva P. 1993 Cadmium, copper and lead in wild rice from central. Canada.

Bioaccessibility of Ba, Cu, Pb, and Zn in urban garden and orchard soils

International Nuclear Information System (INIS)

Cai, Meifang; McBride, Murray B.; Li, Kaiming

2016-01-01

Exposure of young children to toxic metals in urban environments is largely due to soil and dust ingestion. Soil particle size distribution and concentrations of toxic metals in different particle sizes are important risk factors in addition to bioaccessibility of these metals in the particles. Analysis of particle size distribution and metals concentrations for 13 soils, 12 sampled from urban gardens and 1 from orchard found that fine particles (<105 μm) comprised from 22 to 66% by weight of the tested soils, with Ba, Cu, Pb and Zn generally at higher concentrations in the finer particles. However, metal bioaccessibility was generally lower in finer particles, a trend most pronounced for Ba and Pb. Gastric was higher than gastrointestinal bioaccessibility for all metals except Cu. The lower bioaccessibility of Pb in urban garden soils compared to orchard soil is attributable to the higher organic matter content of the garden soils. - Highlights: • The bioaccessibility of metals in urban garden and orchard soils was measured. • Ba, Cu, Pb, Zn were concentrated in fine particles of the soils. • Bioaccessibilities of Ba and Pb were generally lower in fine particles of soils. • Pb bioaccessibility was generally lower in soils with higher organic matter content. • Pb bioaccessibility was lower in urban garden soils than in an orchard soil. - Pb and other trace metals (Ba, Cu, Zn) were concentrated in fine particles of urban and orchard soils, but the bioaccessibility of Ba and Pb was generally lower in finer particles.

Photoluminescence and Raman studies for the confirmation of oxygen vacancies to induce ferromagnetism in Fe doped Mn:ZnO compound

Energy Technology Data Exchange (ETDEWEB)

Das, J., E-mail: jayashree304@gmail.com [Department of Physics, Silicon Institute of Technology, Bhubaneswar 751024, Odisha (India); Department of Physics, College of Science, Engineering and Technology, University of South Africa, Johannesburg 1710 (South Africa); Mishra, D.K. [Department of Physics, College of Science, Engineering and Technology, University of South Africa, Johannesburg 1710 (South Africa); Department of Physics, Institute of Technical Education and Research, Siksha ‘O’ Anusandhan University, Khandagiri Square, Bhubaneswar 751030, Odisha (India); Srinivasu, V.V. [Department of Physics, College of Science, Engineering and Technology, University of South Africa, Johannesburg 1710 (South Africa); Sahu, D.R. [Amity Institute of Nanotechnology, Amity University, Noida (India); Roul, B.K. [Institute of Materials Science, Planetarium Building, Acharya Vihar, Bhubaneswar, Odisha (India)

2015-05-15

With a motivation to compare the magnetic property, we synthesised undoped, transition metal (TM) Mn doped and (Mn:Fe) co-doped ZnO ceramics in the compositions ZnO, Zn{sub 0.98}Mn{sub 0.02}O and Zn{sub 0.96}(Mn{sub 0.02}Fe{sub 0.02})O. Systematic investigations on the structural, microstructural, defect structure and magnetic properties of the samples were performed. Low temperature as well as room temperature ferromagnetism has been observed for all our samples, however, enhanced magnetisation at room temperature has been noticed when ZnO is co-doped with Fe along with Mn. Particularly the sample with the composition Zn{sub 0.96}Mn{sub 0.02}Fe{sub 0.02}O showed a magnetisation value more than double of the sample with composition Zn{sub 0.98}Mn{sub 0.02}O, indicating long range strong interaction between the magnetic impurities leading to higher ferromagnetic ordering. Raman and PL studies reveal presence of higher defects in form of oxygen vacancy clusters created in the sample due to Fe co doping. PL study also reveals enhanced luminescence efficiency in the co doped sample. Temperature dependent magnetisation study of this sample shows the spin freezing temperature around 39 K indicating the presence of small impurity phase of Mn{sub 2−x}Zn{sub x}O{sub 3} type. Electron Spin Resonance signal obtained supports ferromagnetic state in the co doped sample. Enhancement of magnetisation is attributed to interactions mediated by magnetic impurities through large number of oxygen vacancies created by Fe{sup 3+} ions forming bound magnetic polarons (BMP) and facilitating long range ferromagnetic ordering in the co- doped system. - Highlights: • Comparison of magnetic property of ZnO, Zn{sub 0.98}Mn {sub 0.02}O and Zn{sub 0.96}(Mn{sub 0.02}Fe{sub 0.02})O. • Observation of enhanced magnetisation at room temperature in (Mn,Fe) doped ZnO. • Raman and PL studies reveal presence of higher oxygen vacancy clusters. • Electron Spin Resonance signal supports

Porous quasi three-dimensional nano-Mn3O4 + PbO2 composite as supercapacitor electrode material

International Nuclear Information System (INIS)

Dan Yuanyuan; Lin Haibo; Liu Xiaolei; Lu Haiyan; Zhao Jingzhe; Shi Zhan; Guo Yupeng

2012-01-01

Highlights: ► We prepare nano-PbO 2 + Mn 3 O 4 composite material by composite deposition method. ► The nano-PbO 2 + Mn 3 O 4 composite has porous quasi three-dimensional structure. ► Maximum electrochemically effective area (R F ) of the composite is 72. ► The composite shows high specific capacitance up to ∼340 F g −1 . ► A general knowledge of the pesudocapacitance behavior of the composite is acquired. - Abstract: Nano-Mn 3 O 4 + PbO 2 composite electrode materials with different compositions are prepared by anodic composite electrodeposition in Pb 2+ plating solution containing suspended nano-Mn 3 O 4 particles (40–60 nm). The particles are synthesized via one-step homogeneous precipitation at low temperature. The composite materials are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) analyses. The results indicate that the composite composed of γ-Mn 3 O 4 and β-PbO 2 is porous and quasi three-dimensional (3D), and its maximum electrochemically effective area ratio (R F ) is 72. The capacitance performance of the composite is determined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge–discharge test. The composite shows a high specific capacitance up to 338 F g −1 .

Teores de Fe, Mn, Zn, Cu, Ni E Co em solos de referência de Pernambuco Concentrations of Fe, Mn, Zn, Cu, Ni and Co in benchmark soils of Pernambuco, Brazil

Directory of Open Access Journals (Sweden)

Caroline Miranda Biondi

2011-06-01

Full Text Available Metais pesados formam um grupo de elementos com particularidades relevantes e de ocorrência natural no ambiente, como elementos acessórios na constituição de rochas. Esses elementos, apesar de associados à toxidez, exigem tratamento diferenciado em relação aos xenobióticos, uma vez que diversos metais possuem essencialidade (Fe, Mn, Cu, Zn e Ni e benefício (Co comprovados para as plantas. Nesse contexto, o objetivo deste trabalho foi determinar os teores naturais dos metais Fe, Mn, Zn, Ni, Cu e Co nos solos de referência de Pernambuco. Foram coletadas amostras de solo nas três regiões fisiográficas (Zona da Mata, Agreste e Sertão, dos dois primeiros horizontes dos 35 solos de referência do Estado de Pernambuco. A digestão das amostras baseou-se no método 3051A (USEPA, 1998, e a determinação foi efetuada em ICP-OES. Correlações significativas foram estabelecidas entre os metais e entre estes e a fração argila do solo, em ambos os horizontes, indicando a associação comum da maioria dos metais com solos mais argilosos. A maioria dos solos apresentou teores de Fe, Mn, Zn, Cu, Ni e Co menores que os de solos de outras regiões do País, com litologia mais máfica, o que corrobora o fato de que os teores desses elementos são mais diretamente relacionados aos minerais Fe-magnesianos. Os resultados indicam baixo potencial dos solos de Pernambuco em liberar Cu, Co e Ni para plantas, enquanto deficiências de Zn, Fe e Mn são menos prováveis. Os teores naturais de Fe, Mn, Zn, Cu, Ni e Co determinados podem ser utilizados como base para definição dos Valores de Referência de Qualidade para os solos de Pernambuco, de acordo com o preconizado pela legislação nacional.Heavy metals are a group of elements with specific features and natural occurrence in the environment, representing an accessory in the formation of rocks. These elements, although associated with toxicity, must be treated different from xenobiotics, since many

Comparative of Quercus spp. and Salix spp. for phytoremediation of Pb/Zn mine tailings.

Science.gov (United States)

Shi, Xiang; Wang, Shufeng; Sun, Haijing; Chen, Yitai; Wang, Dongxue; Pan, Hongwei; Zou, Yazhu; Liu, Jianfeng; Zheng, Linyu; Zhao, Xiulian; Jiang, Zeping

2017-02-01

A pot experiment was conducted to evaluate the feasibility of using tree seedlings for the phytoremediation of lead/zinc (Pb/Zn) mine tailings. Seedlings of three Quercus spp. (Q. shumardii, Q. phellos, and Q. virginiana) and rooted cuttings of two Salix spp. (S. matsudana and S. integra) were transplanted into pots containing 50 and 100 % Pb/Zn mine tailings to evaluate their tolerance of heavy metals. The five species showed different tolerance levels to the Pb/Zn tailings treatments. Q. virginiana was highly tolerant to heavy metals and grew normally in the Pb/Zn tailings. The root systems showed marked differences between the Quercus spp. and Salix spp., indicating that different mechanisms operated to confer tolerance of heavy metals. The maximum efficiency of photosystem II photochemistry value of the five species showed no differences among the treatments, except for Q. shumardii. All species showed low metal translocation factors (TFs). However, S. integra had significantly higher TF values for Zn (1.42-2.18) and cadmium (1.03-1.45) than did the other species. In this respect, Q. virginiana showed the highest tolerance and a low TF, implying that it is a candidate for phytostabilization of mine tailings in southern China. S. integra may be useful for phytoextraction of tailings in temperate regions.

Effect of 50 MeV Li3 + irradiation on structural and electrical properties of Mn-doped ZnO

Science.gov (United States)

Neogi, S. K.; Chattopadhyay, S.; Banerjee, Aritra; Bandyopadhyay, S.; Sarkar, A.; Kumar, Ravi

2011-05-01

The present work aims to study the effect of ion irradiation on structural and electrical properties and their correlation with the defects in the Zn1 - xMnxO-type system. Zn1 - xMnxO (x = 0.02, 0.04) samples have been synthesized by the solid-state reaction method and have been irradiated with 50 MeV Li3 + ions. The concomitant changes have been probed by x-ray diffraction (XRD), temperature-dependent electrical resistivity and positron annihilation lifetime (PAL) spectroscopy. The XRD result shows a single-phase wurtzite structure for Zn0.98Mn0.02O, whereas for the Zn0.96Mn0.04O sample an impurity phase has been found, apart from the usual peaks of ZnO. Ion irradiation removes this impurity peak. The grain size of the samples is found to be uniform. For Zn0.98Mn0.02O, the observed sharp decrease in room temperature resistivity (ρRT) with irradiation is consistent with the lowering of the full width at half maximum of the XRD peaks. However, for Zn0.96Mn0.04O, ρRT decreases for the initial fluence but increases for a further increase in fluence. All the irradiated Zn0.98Mn0.02O samples show a metal-semiconductor transition in temperature-dependent resistivity measurements at low temperature. But all the irradiated Zn0.96Mn0.04O samples show a semiconducting nature in the whole range of temperatures. Results of room temperature resistivity, XRD and PAL measurements are consistent with each other.

Use of ZnO:Mn particles for degradation of methylene blue by photocatalysis process

International Nuclear Information System (INIS)

Giraldi, T. R.; Swerts, J. P.; Vicente, M. A.; Paris, E.C.; Ribeiro, C.

2016-01-01

The management of water use in the agricultural environment is a key factor to build new environmentally sustainable productive methods. Photocatalysis is a promising method for water decontamination. This research paper aimed to evaluate the photocatalytic potential of pure and Mn-doped ZnO particles. The materials were obtained by the polymeric precursor method, and characterized by X-ray diffraction, N_2 adsorption in low temperature, infrared and ultraviolet spectroscopy, and photoluminescence. In order to evaluate ZnO:Mn particles photo efficiency, experiments were carried out by applying the methylene blue dye solution to photodegradation under UVC exposure. The particles had ZnO single-phase, but low specific surface area. The sample ZnO:0.25% Mn presented higher efficiency in the methylene blue photocatalytic degradation test. This efficiency was related to a higher band gap energy value and a lower rate of electron recombination, which allows greater formation of hydroxyl radicals, which are responsible for dye degradation. (author)

Transfer factors of some selected radionuclides (radioactive Cs, Sr, Mn, Co and Zn) from soil to leaf vegetables

International Nuclear Information System (INIS)

Ban-nai, Tadaaki; Muramatsu, Yasuyuki; Yanagisawa, Kei

1995-01-01

Transfer factors of radionuclides from soil to leaf vegetables (cabbage, Chinese cabbage, komatsuna, spinach and lettuce) have been studied by radiotracer experiments using Andosol as a representative of Japanese soils. The transfer factors of radioactive Cs, Sr, Mn, Co and Zn for edible parts of vegetables (average of five vegetables) were 0.11, 0.24, 0.61, 0.05 and 0.52, respectively. These values should be used in safety assessment for Japanese agricultural environment. The transfer factors of Mn, Co and Zn for spinach were higher than those for the other vegetables. The transfer factors of Cs for different organs of the leaf vegetables were rather homogeneous. The transfer factors of Sr and Mn were higher for older (outer) leaves than younger (inner) ones. In contrast to Sr and Mn, transfer factors of Zn for younger leaves were higher than those for older ones. The distribution ratios of the elements between soil-solution and soil were in the order Sr>Mn>Cs>Co>Zn, whereas the distribution ratios of the elements between plant and soil-solution were in the order Zn>Cs>Mn>Co>Sr. These results indicate that the selectivity for Sr by plants from the soil-solution was low and that for Zn was very high. (author)

Microstructural analysis nanoferritas Mn_0_,_5Zn_0_,_5Fe_2O_4 e Mn_0_,_6_5Zn_0_,_3_5Fe_2O_4 synthesized by combustion reaction

International Nuclear Information System (INIS)

Diniz, V.C.S.; Figueiredo, A.R.; Costa Junior, A.D.S.; Diniz, H.M.; Vieira, D.A.; Costa, A.C.F.M.

2014-01-01

The MnZn ferrites are ferrimagnetic materials that have been studied and used in various technological fields. In this work investigated the microstructural characteristics of ferrites and Mn_0_,_5Zn_0_,_5Fe_2O_4 Mn_0_,_6_5Zn_0_,_3_5Fe_2O_4 synthesized by combustion reaction in 200g scale production. The samples were characterized by XRD, crystallinity, crystallite size, X-ray fluorescence and scanning electron microscopy. Given the results it was observed that for both samples the synthesis combustion reaction was efficient for the production of single-phase ferrites with high crystallinity. With respect to the analysis of X-ray fluorescence was noted that the experimental values composition were consistent with the theoretical values calculated for both samples. Regarding morphology for both samples, the formation of the porous powders with feature consisting of dense clumps in the form of irregular foam was observed. (author)

Dynamical control of Mn spin-system cooling by photogenerated carriers in a (Zn,Mn)Se/BeTe heterostructure

Science.gov (United States)

Debus, J.; Maksimov, A. A.; Dunker, D.; Yakovlev, D. R.; Tartakovskii, I. I.; Waag, A.; Bayer, M.

2010-08-01

The magnetization dynamics of the Mn spin system in an undoped (Zn,Mn)Se/BeTe type-II quantum well was studied by a time-resolved pump-probe photoluminescence technique. The Mn spin temperature was evaluated from the giant Zeeman shift of the exciton line in an external magnetic field of 3 T. The relaxation dynamics of the Mn spin temperature to the equilibrium temperature of the phonon bath after the pump-laser-pulse heating can be accelerated by the presence of free electrons. These electrons, generated by a control laser pulse, mediate the spin and energy transfer from the Mn spin system to the lattice and bypass the relatively slow direct spin-lattice relaxation of the Mn ions.

Effect of 50 MeV Li{sup 3+} irradiation on structural and electrical properties of Mn-doped ZnO

Energy Technology Data Exchange (ETDEWEB)

Neogi, S K; Chattopadhyay, S; Banerjee, Aritra; Bandyopadhyay, S [Department of Physics, University of Calcutta, 92 Acharya Prafulla Chandra Road, Kolkata 700009, West Bengal (India); Sarkar, A [Department of Physics, Bangabasi Morning College, 19 Rajkumar Chakraborty Sarani, Kolkata 700009, West Bengal (India); Kumar, Ravi, E-mail: arbphy@caluniv.ac.in [Department of Material Science and Engineering, NIT, Hamirpur-177005, Himachal Pradesh (India)

2011-05-25

The present work aims to study the effect of ion irradiation on structural and electrical properties and their correlation with the defects in the Zn{sub 1-x}Mn{sub x}O-type system. Zn{sub 1-x}Mn{sub x}O (x = 0.02, 0.04) samples have been synthesized by the solid-state reaction method and have been irradiated with 50 MeV Li{sup 3+} ions. The concomitant changes have been probed by x-ray diffraction (XRD), temperature-dependent electrical resistivity and positron annihilation lifetime (PAL) spectroscopy. The XRD result shows a single-phase wurtzite structure for Zn{sub 0.98}Mn{sub 0.02}O, whereas for the Zn{sub 0.96}Mn{sub 0.04}O sample an impurity phase has been found, apart from the usual peaks of ZnO. Ion irradiation removes this impurity peak. The grain size of the samples is found to be uniform. For Zn{sub 0.98}Mn{sub 0.02}O, the observed sharp decrease in room temperature resistivity ({rho}{sub RT}) with irradiation is consistent with the lowering of the full width at half maximum of the XRD peaks. However, for Zn{sub 0.96}Mn{sub 0.04}O, {rho}{sub RT} decreases for the initial fluence but increases for a further increase in fluence. All the irradiated Zn{sub 0.98}Mn{sub 0.02}O samples show a metal-semiconductor transition in temperature-dependent resistivity measurements at low temperature. But all the irradiated Zn{sub 0.96}Mn{sub 0.04}O samples show a semiconducting nature in the whole range of temperatures. Results of room temperature resistivity, XRD and PAL measurements are consistent with each other.

Hierarchical porous ZnMn_2O_4 microspheres architectured with sub-nanoparticles as a high performance anode for lithium ion batteries

International Nuclear Information System (INIS)

Rong, Haibo; Xie, Guiting; Cheng, Si; Zhen, Zihao; Jiang, Zhongqing; Huang, Jianlin; Jiang, Yu; Chen, Bohong; Jiang, Zhong-Jie

2016-01-01

A simple two-step procedure, which involves the synthesis of the Zn_0_._3_3Mn_0_._6_7CO_3 microspheres through a hydrothermal process and the subsequent calcination, has been used to synthesize the ZnMn_2O_4 microspheres with a hierarchical porous morphology consisting of the ZnMn_2O_4 sub-nanoparticles. When evaluated as anode materials for lithium ion batteries (LIBs), these hierarchical porous ZnMn_2O_4 microspheres could exhibit a stable reversible capability of ∼723.7 mAh g"−"1 at the current density of 400 mA g"−"1, which is much higher than those of the ZnMn_2O_4 based materials reported previously, indicating the great potential of using them as the anode for the LIBs. This is further supported by their better rate capability and higher cycling stability. Careful analysis has shown that the unique porous structure of the hierarchical porous ZnMn_2O_4 microspheres which consists of the ZnMn_2O_4 sub-nanoparticles plays an important role in their higher electrochemical performance, since it allows the accommodation of the volume expansion during the repeated discharge–charge cycles, preventing them from the structural destruction, and increase the accessibility of the electrode material to the Li"+ storage, making a better utilization of active materials and an easy diffusion of electrolytes in and out of the electrode material. - Graphical abstract: The ZnMn_2O_4 microspheres with a hierarchical porous morphology consisting of the ZnMn_2O_4 sub-nanoparticles have been synthesized by the calcination of the Zn_0_._3_3Mn_0_._6_7CO_3 microspheres and could exhibit superior electrochemical performance when used as anode materials for lithium ion batteries. - Highlights: • A simple procedure has been used to synthesize the ZnMn_2O_4 microspheres. • The ZnMn_2O_4 microspheres exhibit excellent performance when used in LIBs. • The porous structure plays a crucial role in their high performance. • These spheres exhibit a good morphology retention

Mn(II), Zn(II) and VO(II) Schiff

Indian Academy of Sciences (India)

Home; Journals; Journal of Chemical Sciences; Volume 113; Issue 3. Synthesis and characterisation of Cu(II), Ni(II), Mn(II), Zn(II) and VO(II) Schiff base complexes derived from o-phenylenediamine and acetoacetanilide. N Raman Y Pitchaikani Raja A Kulandaisamy. Inorganic Volume 113 Issue 3 June 2001 pp 183-189 ...

The Crystal Structure of Micro- and Nanopowders of ZnS Studied by EPR of Mn2+ and XRD.

Science.gov (United States)

Nosenko, Valentyna; Vorona, Igor; Grachev, Valentyn; Ishchenko, Stanislav; Baran, Nikolai; Becherikov, Yurii; Zhuk, Anton; Polishchuk, Yuliya; Kladko, Vasyl; Selishchev, Alexander

2016-12-01

The crystal structure of micro- and nanopowders of ZnS doped with different impurities was analyzed by the electron paramagnetic resonance (EPR) of Mn 2+ and XRD methods. The powders of ZnS:Cu, ZnS:Mn, ZnS:Co, and ZnS:Eu with the particle sizes of 5-7 μm, 50-200 nm, 7-10 μm, and 5-7 nm, respectively, were studied. Manganese was incorporated in the crystal lattice of all the samples as uncontrolled impurity or by doping. The Mn 2+ ions were used as EPR structural probes. It is found that the ZnS:Cu has the cubic structure, the ZnS:Mn has the hexagonal structure with a rhombic distortion, the ZnS:Co is the mixture of the cubic and hexagonal phases in the ratio of 1:10, and the ZnS:Eu has the cubic structure and a distorted cubic structure with stacking defects in the ratio 3:1. The EPR technique is shown to be a powerful tool in the determination of the crystal structure for mixed-polytype ZnS powders and powders with small nanoparticles. It allows observation of the stacking defects, which is revealed in the XRD spectra.

Magnetocapacitance effects in MnZn ferrites

Directory of Open Access Journals (Sweden)

Y. M. Xu

2015-11-01

Full Text Available The magnetocapacitance effects of MnZn ferrites with different initial permeabilities have been studied systematically. Both intrinsic effect associated with magnetoelectric coupling and extrinsic effect, which means the combined contribution of magnetoresistance and the Maxwell-Wagner effect, have been observed simultaneously. Analysis shows that the relationship between the origins of both is in competitive equilibrium. Either of both mechanisms plays a dominant role in magnetocapacitance effects under different conditions, respectively, such as permeability and frequency of applied signals.

The single crystal structure determination of Ln{sub 6}MnSb{sub 15} (Ln=La, Ce), Ln{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} (x∝0.5), and Ln{sub 6}ZnSb{sub 15} (Ln=La-Pr)

Energy Technology Data Exchange (ETDEWEB)

Benavides, Katherine A.; McCandless, Gregory T.; Chan, Julia Y. [Texas Univ., Dallas, Richardson, TX (United States). Dept. of Chemistry and Biochemistry

2017-09-01

Single crystals of Ln{sub 6}MnSb{sub 15} (Ln=La, Ce), Ln{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} (x∝0.5), and Ln{sub 6}ZnSb{sub 15} (Ln=La-Pr) have been successfully grown and the compounds adopt the orthorhombic Ln{sub 6}MnSb{sub 15} structure type (space group Immm), with a∝4.3 Aa, b∝15 Aa, and c∝19 Aa. This structure is comprised of antimony nets and antimony ribbons which exhibit positional disorder at connecting points between antimony substructures, in addition to two partially occupied transition metal sites. The unit cell volumes of the La analogs displayed a systematic decrease upon Zn substitution. However, for the Ce{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} and Pr{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} (x∝0.5), the volumes deviate from linearity as observed in the parent compounds.

Pathways of Pb and Mn observed in a 5-year longitudinal investigation in young children and environmental measures from an urban setting

International Nuclear Information System (INIS)

Gulson, Brian; Mizon, Karen; Taylor, Alan; Korsch, Michael; Davis, J. Michael; Louie, Honway; Wu, Michael; Gomez, Laura; Antin, Luminita

2014-01-01

We monitored 108 children ≤5 years on a 6-month basis for up to 5 years in a major urban setting. Samples (n ∼ 7000) included blood, urine, handwipes (interior, and after exterior playing), 6-day duplicate diet, drinking water, interior house and day care dust-fall accumulation using petri dishes, exterior dust-fall accumulation, exterior dust sweepings, paint, soil and urban air. The geometric mean blood Pb (PbB) was 2.1 μg/dL and blood Mn (MnB) was 10.0 μg/L. Following a path modelling approach, mixed model analyses for a fully adjusted model showed the strongest associations for PbB were with interior house dust and soil; for MnB there were no significant associations with any predictors. Predictor variables only explained 9% of the variance for Pb and 0.7% for Mn. Relationships between environmental measures and PbB in children are not straightforward; soil and dust sweepings contribute only about 1/5th of the amounts to PbB found in other studies. - Highlights: • 5-year longitudinal study of young children in urban setting. • Samples analysed for Pb and Mn in blood and environmental samples. • Modified structural equation modelling. • Strongest associations for blood Pb with house dust and soil. • Soil and dust contribute very small amounts to blood Pb. - This study provides useful insights about the environmental pathways leading to Pb and Mn exposure in young children

Fractal structures in two-metal electrodeposition systems I: Pb and Zn

International Nuclear Information System (INIS)

Nakouzi, Elias; Sultan, Rabih

2011-01-01

Pattern formation in two-metal electrochemical deposition has been scarcely explored in the chemical literature. In this paper, we report new experiments on zinc-lead fractal co-deposition. Electrodeposits are grown in special cells at a fixed large value of the zinc ion concentration, while that of the lead ion is increased gradually. A very wide diversity of morphologies are obtained and classified. Most of the deposited domains are almost exclusively Pb or Zn. But certain regions originating at the base cathode, ranging from a short grass alley to dense, grown-up bushes or shrubs, manifest a combined Pb-Zn composition. Composition is determined using scanning electron microscopy/energy dispersive x ray measurements as well atomic absorption spectroscopy. Pb domains are characterized by shiny leaf-like and dense deposits as well as flowers with round, balloon-like corollas. The Zn zones display a greater variety of morphologies such as thick trunks and thin and fine branching, in addition to minute ''cigar flower'' structures. The various morphologies are analyzed and classified from the viewpoint of fractal nature, characterized by the box-count fractal dimension. Finally, macroscopic spatial alternation between two different characteristic morphologies is observed under certain conditions.

Fabrication of electrospun ZnMn2O4 nanofibers as anode material for lithium-ion batteries

International Nuclear Information System (INIS)

Luo, Lei; Qiao, Hui; Chen, Ke; Fei, Yaqian; Wei, Qufu

2015-01-01

Highlights: • ZnMn 2 O 4 nanofibers were successfully synthesized by a facile electrospinning and calcination method for lithium-ion batteries. • The as-prepared ZnMn 2 O 4 nanofibers, containing PVP and PAN with ratio of 1:9, exhibited a high initial discharge capacity of 1274 mAh g −1 , and the stabilized capacity was as high as 603 mAh g −1 after 60 cycles at a current density of 50 mA g −1 . • The as-prepared ZnMn 2 O 4 anode material showed good lithium storage performances and excellent rate capability and can be a promising electrode material for lithium-ion batteries in the future. - Abstract: In this paper, ZnMn 2 O 4 nanofibers were synthesized by a facile electrospinning and calcination method. Electrochemical properties of the nanofiber anode material for lithium-ion batteries were investigated. The as-prepared ZnMn 2 O 4 nanofibers, containing PVP and PAN with ratio of 1:9, exhibited a high initial discharge capacity of 1274 mAh g −1 , and the stabilized capacity was as high as 603 mAh g −1 after 60 cycles at a current density of 50 mA g −1 . Besides the high specific capacity and good cyclability, the electrode also showed good rate capability. Even at 2000 mA g −1 , the electrode could deliver a capacity of as high as 352 mAh g −1 . The results suggest a promising application of the electrospun ZnMn 2 O 4 nanofibers as anode material for lithium-ion batteries

Laser induced adjustment of the conductivity of rare earth doped Mn-Zn nanoferrite

Directory of Open Access Journals (Sweden)

El-Dek S. I.

2017-10-01

Full Text Available Two series of Mn-Zn nanoferrites (namely Mn1-xZnxFe2O4 and Mn1-xZnxFe2-yRyO4 were synthesized using standard ceramic technique. X-ray diffraction and FT-IR were employed in the chacterization of the nanopowder. The X-ray density for each sample increased after laser irradiation which was correlated with the decrease in the unit cell volume. The study involved the thermal and frequency variation of the dielectric constant and AC conductivity of the investigated samples before and after laser irradiation. The later altered the conductivity by decreasing its value for the rare earth doped samples except for the Sm3+ doped one. The results suggested the exploitation of Mn-Zn doped rare earth nanoferrites in many technological applications demanding high resistivity.

Characterization of Aerosols Containing Zn, Pb, and Cl from an Industrial Region of Mexico City

International Nuclear Information System (INIS)

Moffet, Ryan C.; Desyaterik, Yury; Hopkins, Rebecca J.; Tivanski, Alexei V.; Gilles, Marry K.; Wang, Yan A.; Shutthanandan, V.; Molina, Luisa T.; Abraham, Rodrigo G.; Johnson, Kirsten S.; Mugica, Violeta; Molina, Mario J.; Laskin, Alexander; Prather, Kimberly A.

2008-01-01

During the March, 2006 MILAGRO campaign, measurements in the Northern Mexico City Metropolitan Area revealed the frequent appearance of particles with a characteristically high content of internally mixed Zn, Pb, Cl, and P. A comprehensive study of the chemical and physical properties of these particles was performed using a complementary combination of aerosol measurement techniques. Individual particles were analyzed using Aerosol Time-of-Flight Mass Spectrometry (ATOFMS) and Computer Controlled Scanning Electron Microscopy/Energy Dispersive X-Ray spectroscopy (CCSEM/EDX). Proton Induced X-Ray Emission (PIXE) analysis of bulk aerosol samples provided time-resolved mass concentrations of individual elements. The PIXE measurements indicated that Zn is more strongly correlated with Cl than with any other element and that Zn concentrations are higher than other non-ferrous transition metals. The Zn- and Pb-containing particles have both spherical and non-spherical morphologies. Many metal rich particles had needle-like structures and were found to be composed of ZnO and/or Zn(NO3)2 6H2O as indicated by scanning transmission x-ray microscopy/near edge X-ray absorption spectroscopy (STXM/NEXAFS). The Zn and Pb rich particles were primarily in the submicron size range and internally mixed with elemental carbon. The unique chemical associations most closely match signatures acquired for garbage incineration. This unique combination of complementary analytical techniques has allowed for a comprehensive evaluation of Zn- and Pb- containing particles in a complex urban environment, highlighting unique characteristics that give powerful insight into their origin

A review of Pb-Sb(As-S, Cu(Ag-Fe(Zn-Sb(As-S, Ag(Pb-Bi(Sb-S and Pb-Bi-S(Te sulfosalt systems from the Boranja orefield, West Serbia

Directory of Open Access Journals (Sweden)

Radosavljević Slobodan A.

2016-01-01

Full Text Available Recent mineralogical, chemical, physical, and crystallographic investigations of the Boranja orefield showed very complex mineral associations and assemblages where sulfosalts have significant role. The sulfosalts of the Boranja orefield can be divided in four main groups: (i Pb-Sb(As-S system with ±Fe and ±Cu; (ii Cu(Ag-Fe(Zn-Sb(As-S system; (iii Ag(Pb-Bi(Sb-S; (iv and Pb-Bi-S(Te system. Spatially, these sulfosalts are widely spread, however, they are the most abundant in the following polymetallic deposits and ore zones: Cu(Bi-FeS Kram-Mlakva; Pb(Ag-Zn-FeS2 Veliki Majdan (Kolarica-Centralni revir-Kojići; Sb-Zn-Pb-As Rujevac; and Pb-Zn-FeS2-BaSO4 Bobija. The multi stage formation of minerals, from skarnhydrothermal to complex hydrothermal with various stages and sub-stages has been determined. All hydrothermal stages and sub-stages of various polymetallic deposits and ore zones within the Boranja orefield are followed by a variety of sulfosalts. [Projekat Ministarstva nauke Republike Srbije, br. OI-176016: Magmatism and geodynamics of the Balkan Peninsula from Mesozoic to present day: Significance for the formation of metallic and non-metallic mineral deposits

Mn-doped ZnFe{sub 2}O{sub 4} nanoparticles with enhanced performances as anode materials for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Tang, Xiaoqin [Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Hou, Xianhua, E-mail: houxh5697@163.com [Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Engineering Research Center of Materials and Technology for Electrochemical Energy Storage, Guangzhou 510006 (China); Yao, Lingmin [Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Hu, Shejun [Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Engineering Research Center of Materials and Technology for Electrochemical Energy Storage, Guangzhou 510006 (China); Liu, Xiang, E-mail: iamxliu@njtech.edu.cn [Institute of Advanced Materials, Nanjing University of Technology, Nanjing 210009 (China); Xiang, Liangzhong [Department of Radiation Physics, Stanford University, Arastradero, PA 1070 (United States)

2014-09-15

Highlights: • Mn-doped ZnFe{sub 2}O{sub 4} nanoparticles have been synthesized by hydrothermal method. • Zn{sub 0.96}Mn{sub 0.04}Fe{sub 2}O{sub 4} electrode shows the highest reversible capacity of 1157 mA h g{sup −1}. • The Zn{sub 0.96}Mn{sub 0.04}Fe{sub 2}O{sub 4} electrode shows promising cycling stability. - Abstract: Nanocrystalline Zn{sub 1−x}Mn{sub x}Fe{sub 2}O{sub 4} (x = 0, 0.02, 0.04, 0.06, 0.08, 0.1) have been successfully synthesized by one-step hydrothermal method. The morphologies and electrochemical performance of Mn-doped ZnFe{sub 2}O{sub 4} in various proportions were investigated at room temperature, respectively. The Zn{sub 1−x}Mn{sub x}Fe{sub 2}O{sub 4} (x = 0.04) electrode in the as-synthesized samples showed the highest specific capacity of 1547 mA h g{sup −1} and 1157 mA h g{sup −1} in the initial discharge/charge process, with a coulombic efficiency of 74.8%. Additionally, excellent cycling stability was performed with a 1214 mA h g{sup −1} capacity retention at a current density of 100 mA g{sup −1} after 50 cycles. The corresponding mechanism was proposed which indicated that the Mn-doped ZnFe{sub 2}O{sub 4} nanoparticles experienced an aggregation thermochemical reaction among ZnO, MnO and Fe{sub 2}O{sub 3} subparticles.

Influence of pH on luminescence from water-soluble colloidal Mn-doped ZnSe quantum dots capped with different mercaptoacids

International Nuclear Information System (INIS)

Hardzei, Maryia; Artemyev, Mikhail

2012-01-01

Water-soluble ZnSe/ZnS core–shell quantum dots with ZnSe core doped by manganese ions show different luminescence response to pH changes in aqueous solutions depending on the type of solubilizing agents (thioglycolic acid, mercaptoundecanoic acid, sodium mercaptopropylsulfonate). In the case of long-chain mercaptoundecanoic acid only excitonic emission is affected by pH changes. Short-chain thioglycolic acid brings about equal excitonic/Mn emission variations with pH, while mercaptopropylsulfonate-stabilized quantum dots are insensitive to pH. The mechanism discussed here is based on the competition between different relaxation channels for excited excitons in ZnSe: excitonic radiative recombination, energy transfer to Mn ion and the photogenerated electron trapping due to the presence of protonated carboxyl group. ZnSe:Mn/ZnS quantum dots stabilized with long-chain mercaptoacids may be used as a new type of fluorescence ratiometric pH-sensor or indicator. - Highlights: ► Prepared ZnSe:Mn/ZnS quantum dots capped with different mercaptoacids in water. ► Photoluminescence intensity of ZnSe:Mn/ZnS quantum dots varied with pH. ► Character of luminescence variations depends on the sort of mercaptoacid capping. ► Competition between different excitonic relaxation channels for different caps.

Influence of hydrology on heavy metal speciation and mobility in a Pb-Zn mine tailing

International Nuclear Information System (INIS)

Kovacs, Elza; Dubbin, William E.; Tamas, Janos

2006-01-01

Among the inorganic toxicants of greatest concern in mine tailings, Pb, Zn, Cu, Cd and As figure prominently due to their abundance and potential toxicity. Here we report on their biolability and solid-phase speciation in two sediment cores subject to variable hydrological regimes at an abandoned pyritic mine tailing. The oxic conditions of well-drained sediments induced pyrite oxidation and the subsequent liberation of H + , SO 4 2- and considerable quantities of Fe(III), which precipitated as goethite. Solubility of Pb, Zn, Cu and Cd was closely coupled to pH and goethite presence. Metal lability was particularly low in zones of neutralization, formed by the accumulation of calcite, first carried then deposited by percolating waters in both saturated and unsaturated cores. We conclude that differential hydrology induces variable heavy metal speciation and biolability in Pb-Zn mine tailings, and suggest that site-specific risk assessments must account for past and present hydrological regimes. - Variable hydrology influences heavy metal speciation and mobility, and the formation of neutralization zones, in a Pb-Zn mine tailing

CL from ZnO nanowires and microneedles Co-doped with N and Mn

International Nuclear Information System (INIS)

Herrera, M; Morales, A; Díaz, J A

2014-01-01

Cathodoluminescence (CL) was used to study the luminescence emission of ZnO : N, Mn nanowires and microneedles grown by thermal evaporation. CL spectra acquired at room temperature showed the presence of near band edge and defect-related emissions. The defect related emission comprised two bands centered at 2.28 and 2.5 eV. The first component was attributed to the formation of spinel ZnMn 2 O 4  and the second to the well-known ZnO green emission. CL spectra acquired at 100 K showed two emissions centered at 3.22 and 3.25 eV that were attributed to donor–acceptor pair (DAP) and FA transitions, respectively. It was proposed that substitutional nitrogen (N O ) and zinc interstitial (Zn i ) were acceptor and shallow-donor centers in the DAP transition. (paper)

Remediation of a historically Pb contaminated soil using a model natural Mn oxide waste.

Science.gov (United States)

McCann, Clare M; Gray, Neil D; Tourney, Janette; Davenport, Russell J; Wade, Matthew; Finlay, Nina; Hudson-Edwards, Karen A; Johnson, Karen L

2015-11-01

A natural Mn oxide (NMO) waste was assessed as an in situ remediation amendment for Pb contaminated sites. The viability of this was investigated using a 10 month lysimeter trial, wherein a historically Pb contaminated soil was amended with a 10% by weight model NMO. The model NMO was found to have a large Pb adsorption capacity (qmax 346±14 mg g(-1)). However, due to the heterogeneous nature of the Pb contamination in the soils (3650.54-9299.79 mg kg(-1)), no treatment related difference in Pb via geochemistry could be detected. To overcome difficulties in traditional geochemical techniques due to pollutant heterogeneity we present a new method for unequivocally proving metal sorption to in situ remediation amendments. The method combines two spectroscopic techniques; namely electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS). Using this we showed Pb immobilisation on NMO, which were Pb free prior to their addition to the soils. Amendment of the soil with exogenous Mn oxide had no effect on microbial functioning, nor did it perturb the composition of the dominant phyla. We conclude that NMOs show excellent potential as remediation amendments. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Bismuth zinc vanadate, BiZn{sub 2}VO{sub 6}: New crystal structure type and electronic structure

Energy Technology Data Exchange (ETDEWEB)

Eliziario Nunes, Sayonara [Department of Chemistry, Durham University, South Road, Durham DH1 3LE (United Kingdom); Department of Materials Engineering, Federal University of São Carlos, 13565-905 São Carlos, SP (Brazil); Wang, Chun-Hai; So, Karwei; Evans, John S.O. [Department of Chemistry, Durham University, South Road, Durham DH1 3LE (United Kingdom); Evans, Ivana Radosavljević, E-mail: ivana.radosavljevic@durham.ac.uk [Department of Chemistry, Durham University, South Road, Durham DH1 3LE (United Kingdom)

2015-02-15

We report a combined experimental and computational study of the crystal structure and electronic properties of bismuth zinc vanadate, BiZn{sub 2}VO{sub 6}, known for its visible light photocatalytic activity. The crystal structure has been solved from laboratory powder X-ray diffraction data using the repeated minimisations from random starting values method. BiZn{sub 2}VO{sub 6} adopts a new structure type, based on the following building blocks: corner- and edge-sharing ZnO{sub 4} tetrahedra, ZnO{sub 6} octahedra and VO{sub 4} tetrahedra, and Bi{sub 2}O{sub 12} dimers. It is the only known member of the BiM{sub 2}AO{sub 6} (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family which does not appear to be structurally closely related to others. The electronic structure of BiZn{sub 2}VO{sub 6}, calculated by DFT methods, shows that it is an indirect gap semiconductor with a calculated band gap of 1.6 eV, which compares favourably to the experimentally measured value of 2.4 eV. - Graphical abstract: The crystal structure of BiZn{sub 2}VO{sub 6}, a new structure type in the BiM{sub 2}AO{sub 6} (M=Mg, Ca, Cd, Cu, Pb, Mn, Zn; A=V, P, As) family. - Highlights: • Structure solution from PXRD data by repeated minimisations from random starting values. • New structure type in the BiM{sub 2}AO{sub 6} (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family. • Electronic structure calculation.

Mn doping in ZnO nanoparticles: effects investigated by positron lifetime and Doppler broadening studies

Energy Technology Data Exchange (ETDEWEB)

Roy, B.; Karmakar, B.; Pal, M. [Department of Physics, University of Burdwan, Golapbag, Burdwan (India); Nambissan, P.M.G. [Saha Institute of Nuclear Physics, Kolkata (India)

2009-11-15

Positron lifetime and Doppler broadening measurements in nanocrystalline zinc oxide (ZnO) indicated the negatively charged trivacancy-type defects V{sub Zn+O+Zn} as the predominant positron trapping sites within the nanocrystallites. They got converted to neutral divacancies (V{sub Zn+O}) on doping with manganese (Mn). Further doping resulted in the reduction of the size of the nanocrystallites. At still increased doping concentrations, a new phase ZnMn{sub 2}O{sub 4} was formed. It had a normal spinel structure with positron trapping centers at some of the tetrahedral and octahedral sites. X-ray diffraction and transmission electron micro-scopy studies confirmed these findings. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

MODEL ADSORPSI TIMBAL (PB DAN SENG (ZN DALAM SISTEM AIR-SEDIMEN DI WADUK RIAM KANAN KALIMANTAN SELATAN

Directory of Open Access Journals (Sweden)

Chatimatun Nisa

2013-04-01

Full Text Available Heavy metals are often considered as main contaminant in water pollution and its highly dangerous for living organisms in the contaminated area. The aim of this research is to predict the movement pattern of Pb and Zn metal ions from water onto sediment in the Riam Kanan Reservoir, Aranio Sub-district, Banjar District. In addition, this study is expected to give information on the initial condition of Riam Kanan reservoir; dynamics; and the fate of Pb and Zn ions from upstream to downstream. The samples were analysed using AAS (Atomic Absorption Spectrophotometer based on the Indonesian National Standard (SNI. Result of laboratory analysis showed that in the water, contents of metal Pb were 0.0494 ppm – 0.2582 ppm, Zn 0.0002 ppm – 0.0370 ppm. In the sediment, contents of Pb were 0.8311 mg/kg – 21.1756 mg/kg and Zn 3.3778 mg/kg – 28.3522 mg/kg. Based on the experimental data, it was found that the displacement of Pb and Zn onto sediment complies with Langmuir adsorption model where the determination coefficient (R2 were 0.8167 and 0.8801 respectively.

(Zn, Mg)2GeO4:Mn2+ submicrorods as promising green phosphors for field emission displays: hydrothermal synthesis and luminescence properties.

Science.gov (United States)

Shang, Mengmeng; Li, Guogang; Yang, Dongmei; Kang, Xiaojiao; Peng, Chong; Cheng, Ziyong; Lin, Jun

2011-10-07

(Zn(1-x-y)Mg(y))(2)GeO(4): xMn(2+) (y = 0-0.30; x = 0-0.035) phosphors with uniform submicrorod morphology were synthesized through a facile hydrothermal process. X-Ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), photoluminescence (PL), and cathodoluminescence (CL) spectroscopy were utilized to characterize the samples. SEM and TEM images indicate that Zn(2)GeO(4):Mn(2+) samples consist of submicrorods with lengths around 1-2 μm and diameters around 200-250 nm, respectively. The possible formation mechanism for Zn(2)GeO(4) submicrorods has been presented. PL and CL spectroscopic characterizations show that pure Zn(2)GeO(4) sample shows a blue emission due to defects, while Zn(2)GeO(4):Mn(2+) phosphors exhibit a green emission corresponding to the characteristic transition of Mn(2+) ((4)T(1)→(6)A(1)) under the excitation of UV and low-voltage electron beam. Compared with Zn(2)GeO(4):Mn(2+) sample prepared by solid-state reaction, Zn(2)GeO(4):Mn(2+) phosphors obtained by hydrothermal process followed by high temperature annealing show better luminescence properties. In addition, codoping Mg(2+) ions into the lattice to substitute for Zn(2+) ions can enhance both the PL and CL intensity of Zn(2)GeO(4):Mn(2+) phosphors. Furthermore, Zn(2)GeO(4):Mn(2+) phosphors exhibit more saturated green emission than the commercial FEDs phosphor ZnO:Zn, and it is expected that these phosphors are promising for application in field-emission displays.

Magnetic and optical properties of Mn-doped ZnO vertically aligned nanorods synthesized by hydrothermal technique

Energy Technology Data Exchange (ETDEWEB)

Panda, J.; Sasmal, I.; Nath, T. K., E-mail: tnath@phy.iitkgp.ernet.in, E-mail: tapnath@gmail.com [Department of Physics, Indian Institute Technology Kharagpur, West Bengal, 721302 (India)

2016-03-15

In this paper we have reported the synthesis of high quality vertically aligned undoped and Mn-doped ZnO single crystalline nanorods arrays on Si (100) substrates using two steps process, namely, initial slow seed layer formation followed by solution growth employing wet chemical hydrothermal method. The shapes of the as grown single crystalline nanorods are hexagonal. The diameter and length of the as grown undoped ZnO nanorods varies in the range of 80-150 nm and 1.0 - 1.4 μm, respectively. Along with the lattice parameters of the hexagonal crystal structure, the diameter and length of Mn doped ZnO nanorods are found to increase slightly as compared to the undoped ZnO nanorods. The X-ray photoelectron spectroscopy confirms the presence of Mn atoms in Mn{sup 2+} state in the single crystalline ZnO nanorods. The recorded photoluminescence spectrum contains two emissions peaks having UV exciton emissions along with a green-yellow emission. The green-yellow emissions provide the evidence of singly ionized oxygen vacancies. The magnetic field dependent magnetization measurements [M (H)] and zero field cooled (ZFC) and field cooled (FC) magnetization [M(T)] measurements have been carried out at different isothermal conditions in the temperature range of 5-300 K. The Mn doped ZnO nanorods clearly show room temperature ferromagnetic ordering near room temperature down to 5 K. The observed magnetization may be attributed to the long range ferromagnetic interaction between bound magnetic polarons led by singly charged oxygen vacancies.

Determination of toxicity limiting values of Zn, Cu, and Pb for oat and red clover

Energy Technology Data Exchange (ETDEWEB)

Hodenberg, A V; Finck, A

1975-01-01

Toxicity limiting values of Zn, Cu and Pb are determined in order to investigate the causes of growth damages in certain fields. Since the true toxicity limit is difficult to estimate, a somewhat higher content is called the toxicity limiting value resulting after the subtraction of a significant yield difference. The pot experiments with increasing fertilization of Zn, Cu and Pb in soil cultures gave the following results. For Zn, the toxicity limit is 410 ppm in oats at the beginning of tilling. In red clover six weeks of age, it is only 290 ppm of Zn and therefore much lower. For Cu, the toxicity limit is 20 ppm in oats at the beginning of tilling and 18 ppm in six weeks old red clover. For Pb, a toxic effect could be observed above 50 ppm, but this does not seem to be the true limit because of disturbing salt effects.

Performance of Zn-Fe-Mn/MCM-48 sorbents for high temperature H2S removal and analysis of regeneration process

Science.gov (United States)

Huang, Z. B.; Liu, B. S.; Wang, F.; Amin, R.

2015-10-01

MCM-48 was synthesized using a rapid and facile process at room temperature. A series of 50%Zn-Fe-Mn/MCM-48 sorbents were prepared and their performance of hot coal gas desulfurization was investigated. High breakthrough sulfur capacity (13.2 g-S/100 g sorbent) and utilization (66.1%) of 50%1Zn2Fe2Mn/MCM-48 sorbent at 550 °C was achieved. The characterization results of XRD, BET, TPR and FT-IR revealed that MCM-48 had excellent thermal stability at less than 700 °C, ZnMn2O4 and (Mn, Zn)Fe2O4 were mainly active particles in fresh sorbents which were highly dispersed on support. The MCM-48 mesoporous structure remained intact after eight successive desulfurization/regeneration cycles. The regeneration process of 50%1Zn2Fe2Mn/MCM-48 sorbent was analyzed, it indicated that the breakthrough sulfur capacity decline of sorbent was due to the migration of Zn onto the sorbent surface and Zn accumulated on the surface and vaporized to the exterior from the surface. In the TPO test, the oxidation of Zn was different for 50%Zn/MCM-48 at 700 °C. It revealed that the temperature of regeneration for ZnO sorbent should be higher than 700 °C.

Determination of Fe, Hg, Mn, and Pb in three-rings of poplar (Populus alba L.) by U-shaped DC arc

Science.gov (United States)

Marković, D. M.; Novović, I.; Vilotić, D.; Ignjatović, Lj.

2007-09-01

The U-shaped DC arc with aerosol supply was applied for the determination of Fe, Hg, Mn, and Pb in poplar (Populus alba L.) tree-rings. By optimization of the operating parameters and by selection of the most appropriate signal integration time (20 s for Fe, Mn, and Pb and 30 s for Hg), the obtained limits of detection for Fe, Hg, Mn, and Pb are 5.8, 2.6, 1.6, and 2.0 ng/ml, respectively. The detection limits achieved by this method for Fe, Hg, Mn, and Pb are comparable with the detection limits obtained for these elements by such methods as inductively coupled plasma-atomic emission spectrometry (ICP-AES), direct coupled plasmatomic emission spectrometry (DCP-AES), and microwave-induced plasma-atomic emission spectrometry (MIP-AES). We used the tree-rings of poplar from two different locations. The first one is in the area close to the power plant “Nikola Tesla” TENT A, Obrenovac, while the other one is in the urban area of Novi Sad. In almost all cases, samples from the location at Obrenovac registered elevated average concentrations of Fe, Hg, Mn, and Pb in the tree-rings of poplar.

High temperature superconductivity in Zn and Mn substituted (Tl,Cr)Sr2CaCu2O7

International Nuclear Information System (INIS)

Lo, S.V.; Abd Shukor, R.

1999-01-01

Samples with nominal starting composition (TICr 0 .15)Sr 2 (Ca 1-x M x )Cu 2 O 7 (TI-1212) for x=0 - 0.7 with M= Zn and Mn have been prepared and investigated by powder X-ray diffraction (XRD) and electrical resistance measurements. All sample showed a mixed phase of 1212 and 1201. Dominant 1212-phase was observed for x=0.0-0.5 and x=0.0-0.4, for Zn and Mn series, respectively. The superconducting transition temperature was suppressed when Zn and Mn are substituted at the Ca site. For the Zn series the normal state behavior is metallic throughout the doping range. For the Mn series the normal state behavior is metallic for 0.1≤x≥0.3 and semiconducting like x>0.3. The suppression of T c and formation of the TI-1212 phase are discussed in terms of the ionic radius and valence state of the substituted elements. (author)

Aqueous-phase synthesis and color-tuning of core/shell/shell inorganic nanocrystals consisting of ZnSe, (Cu, Mn)-doped ZnS, and ZnS

Energy Technology Data Exchange (ETDEWEB)

Choi, Jongwan; Yoon, Sujin [Department of Chemistry and Research Institute for Natural Science, Hanyang University, Seoul, 133-791 (Korea, Republic of); Kim, Felix Sunjoo, E-mail: fskim@cau.ac.kr [School of Chemical Engineering and Materials Science, Chung-Ang University, Seoul, 156-756 (Korea, Republic of); Kim, Nakjoong, E-mail: kimnj@hanyang.ac.kr [Department of Chemistry and Research Institute for Natural Science, Hanyang University, Seoul, 133-791 (Korea, Republic of)

2016-06-25

We report synthesis of colloidal nanocrystals based on ZnSe core, (Cu,Mn)-doped ZnS inner-shell, and ZnS outer-shell by using an eco-friendly method and their optical properties. Synthesis of core/shell/shell nanocrystals was performed by using a one-pot/three-step colloidal method with 3-mercaptopropionic acid as a stabilizer in aqueous phase at low temperature. A double-shell structure was employed with inner-shell as a host for doping and outer-shell as a passivation layer for covering surface defects. Copper and manganese were introduced as single- or co-dopants during inner-shell formation, providing an effective means to control the emission color of the nanocrystals. The synthesized nanocrystals showed fluorescent emission ranging from blue to green, to white, and to orange, adjusted by doping components, amounts, and ratios. The photoluminescence quantum yields of the core/doped-shell/shell nanocrystals approached 36%. - Highlights: • ZnSe/ZnS:(Cu,Ms)/ZnS core/(doped)shell/shell nanocrystals were synthesized in an aqueous phase. • Emission color of nanocrystals was controlled from blue to white to orange by adjusting the atomic ratio of Cu and Mn co-dopants. • Photoluminescence quantum yields of the colloidal nanocrystals approached 36%.

UV Light-Driven Photodegradation of Methylene Blue by Using Mn0.5Zn0.5Fe2O4/SiO2 Nanocomposites

Science.gov (United States)

Indrayana, I. P. T.; Julian, T.; Suharyadi, E.

2018-04-01

The photodegradation activity of nanocomposites for 20 ppm methylene blue solution has been investigated in this work. Nanocomposites Mn0.5Zn0.5Fe2O4/SiO2 have been synthesized using coprecipitation method. The X-ray diffraction (XRD) pattern confirmed the formation of three phases in sample Mn0.5Zn0.5Fe2O4/SiO2 i.e., Mn0.5Zn0.5Fe2O4, Zn(OH)2, and SiO2. The appearance of SiO2 phase showed that the encapsulation process has been carried out. The calculated particles size of Mn0.5Zn0.5Fe2O4/SiO2 is greater than Mn0.5Zn0.5Fe2O4. Bonding analysis via vibrational spectra for Mn0.5Zn0.5Fe2O4/SiO2 confirmed the formation of bonds Me-O-Si stretching (2854.65 cm-1) and Si-O-Si asymmetric stretching (1026.13 cm-1). The optical gap energy of Mn0.5Zn0.5Fe2O4/SiO2 was smaller (2.70 eV) than Mn0.5Zn0.5Fe2O4 (3.04 eV) due to smaller lattice dislocation and microstrain that affect their electronic structure. The Mn0.5Zn0.5Fe2O4/SiO2 showed high photodegradation ability due to smaller optical gap energy and the appearance of SiO2 ligand that can easily attract dye molecules. The Mn0.5Zn0.5Fe2O4/SiO2 also showed high degradation activity even without UV light radiation. The result showed that photodegradation reaction doesn’t follow pseudo-first order kinetics.

Solvothermal synthesis of Zn{sub 2}GeO{sub 4}:Mn{sup 2+} nanophosphor in water/diethylene glycol system

Energy Technology Data Exchange (ETDEWEB)

Takeshita, Satoru; Honda, Joji [Department of Applied Chemistry, Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan); Isobe, Tetsuhiko, E-mail: isobe@applc.keio.ac.jp [Department of Applied Chemistry, Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan); Sawayama, Tomohiro; Niikura, Seiji [SINLOIHI Company, Limited, 2-19-12 Dai, Kamakura 247-8550 (Japan)

2012-05-15

The influence of aging of the suspension containing the amorphous precusors on structural, compositional and photoluminescent properties is studied to understand the mechanism on the formation of Zn{sub 2}GeO{sub 4}:Mn{sup 2+} nanoparticles during the solvothermal reaction in the water/diethylene glycol mixed solvent. Aging at 200 Degree-Sign C for 20 min forms the crystalline Zn{sub 2}GeO{sub 4} nanorods and then they grow up to {approx} 50 nm in mean length after aging for 240 min. Their interplanar spacing of (410) increases with increasing the aging time. The photoluminescence intensity corresponding to the d-d transition of Mn{sup 2+} increases with increasing the aging time up to 120 min, and then decreases after aging for 240 min. The photoluminescence lifetime decreases with increasing the aging time, indicating the locally concentrated Mn{sup 2+} ions. These results reveal that Mn{sup 2+} ions gradually replace Zn{sup 2+} ions near surface through repeating dissolusion and precipitation processes during prolonged aging after the complete crystallization of Zn{sub 2}GeO{sub 4}. - Graphical abstract: TEM images of Zn{sub 2}GeO{sub 4}:Mn{sup 2+} nanoparticles aged at 200 Degree-Sign C for different aging times in the mixed solvent of water and diethylene glycol. Highlights: Black-Right-Pointing-Pointer Mechanism on formation of Zn{sub 2}GeO{sub 4}:Mn{sup 2+} nanophosphor under solvothermal condition. Black-Right-Pointing-Pointer Zn{sub 2}GeO{sub 4} nanorods crystallize via amorphous precursors. Black-Right-Pointing-Pointer Gradual substitution of Mn{sup 2+} during prolonged aging. Black-Right-Pointing-Pointer Such an inhomogeneous Mn{sup 2+} doping process results in concentration quenching.

Behaviors of heavy metals (Cd, Cu, Ni, Pb and Zn) in soil amended with composts.

Science.gov (United States)

Gusiatin, Zygmunt Mariusz; Kulikowska, Dorota

2016-09-01

This study investigated how amendment with sewage sludge compost of different maturation times (3, 6, 12 months) affected metal (Cd, Cu, Ni, Pb, Zn) bioavailability, fractionation and redistribution in highly contaminated sandy clay soil. Metal transformations during long-term soil stabilization (35 months) were determined. In the contaminated soil, Cd, Ni and Zn were predominately in the exchangeable and reducible fractions, Pb in the reducible fraction and Cu in the reducible, exchangeable and oxidizable fractions. All composts decreased the bioavailability of Cd, Ni and Zn for up to 24 months, which indicates that cyclic amendment with compost is necessary. The bioavailability of Pb and Cu was not affected by compost amendment. Based on the reduced partition index (IR), metal stability in amended soil after 35 months of stabilization was in the following order: Cu > Ni = Pb > Zn > Cd. All composts were more effective in decreasing Cd, Ni and Zn bioavailability than in redistributing the metals, and increasing Cu redistribution more than that of Pb. Thus, sewage sludge compost of as little as 3 months maturation can be used for cyclic amendment of multi-metal-contaminated soil.

Simple and greener synthesis of highly photoluminescence Mn{sup 2+}-doped ZnS quantum dots and its surface passivation mechanism

Energy Technology Data Exchange (ETDEWEB)

Wang, Yongbo; Liang, Xuhua; Ma, Xuan; Hu, Yahong [School of Chemical Engineering, Northwest University, No. 229 Taibai North Road, Xi’an, Shannxi, 710069 (China); Hu, Xiaoyun; Li, Xinghua [Department of Physics, Northwest University, No. 229 Taibai North Road, Xi’an, Shannxi, 710069 (China); Fan, Jun, E-mail: fanjun@nwu.edu.cn [School of Chemical Engineering, Northwest University, No. 229 Taibai North Road, Xi’an, Shannxi, 710069 (China)

2014-10-15

Graphical abstract: TEM and HRTEM (inset) images of the as-prepared Mn{sup 2+}-doped ZnS QDs and the passivation mechanism model of GSH-capped ZnS QDs (b). - Highlights: • Highly photoluminescent Mn{sup 2+}-doped ZnS quantum dots were synthesized by a simple synthetic method. • The effects of Mn{sup 2+} doping concentration, reaction time and temperature on PL intensity were investigated. • The mechanism of surface passivation was described. - Abstract: In this paper, we reported a simple synthetic method of highly photoluminescent (PL) and stable Mn{sup 2+}-doped ZnS quantum dots (QDs) with glutathione (GSH) as the capping molecule and focused on mechanism of the surface passivation of QDs. The Mn{sup 2+}-doped ZnS QDs that was synthesized in basic solution (pH 10) at 120 °C for 5 h exhibited blue trap-state emission around 418 nm and a strong orange-red emission at about 580 nm with an excitation wavelength of 330 nm. The optimum doping concentration is determined to be 1.5 at.%, and the present Mn{sup 2+}-doped ZnS QDs synthesized under the optimal reaction condition exhibited a quantum yield of 48%. High resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD) indicated that the Mn{sup 2+}-doped ZnS QDs were 3–5 nm in size with a zinc blend structure. More importantly, the PL intensity and chemical stability can be improved using organic ligand modification strategies, it was found that GSH could passivate surface defects very efficiently by comparing and analyzing the results of the different organic ligands modification. The cadmium-free Mn{sup 2+}-doped ZnS QDs well-passivated with GSH as capping molecule acquired the advantages of strong PL and excellent chemical stability, which are important to QD applications.

Magnetization of correlated electron systems. MnSi thin films, CrB2 single crystals and two-dimensional electron systems in MgZnO/ZnO

International Nuclear Information System (INIS)

Brasse, Matthias

2014-01-01

Torque magnetometry at low temperature is performed to investigate the magnetic properties of MnSi thin films, of a CrB 2 single crystal and of a two-dimensional electron system (2DESs) formed at the interface of MgZnO/ZnO. The magnetic anisotropy and phase diagram of MnSi as well as information on the electronic structure of CrB 2 are obtained. The MgZnO/ZnO 2DESs exhibits the de Haas-van Alphen effect and non-equilibrium currents which are analyzed in order to determine ground state properties and excited states, respectively.

Study of defects and vacancies in structural properties of Mn, co-doped oxides: ZnO

Science.gov (United States)

Kumar, Harish; Kaushik, A.; Alvi, P. A.; Dalela, B.; Dalela, S.

2018-05-01

The paper deals with the Structural properties on Mn, Co doped oxides ZnO samples using XRD, Positron Annihilation Lifetime (PAL) Spectra and Raman Spectra. The Mn, Co doped ZnO samples crystallize in a wurtzite structure without any impurity phases in XRD Spectra. The defect state of these samples has been investigated by using positron annihilation lifetime (PAL) spectroscopy technique in which all the relevant lifetime parameters are measured for all the spectra. The results are explained in the direction of doping concentration in these samples in terms of defects structure on Zn lattice site VZn and oxygen defects Vo.

Modelling equilibrium adsorption of single, binary, and ternary combinations of Cu, Pb, and Zn onto granular activated carbon.

Science.gov (United States)

Loganathan, Paripurnanda; Shim, Wang Geun; Sounthararajah, Danious Pratheep; Kalaruban, Mahatheva; Nur, Tanjina; Vigneswaran, Saravanamuthu

2018-03-30

Elevated concentrations of heavy metals in water can be toxic to humans, animals, and aquatic organisms. A study was conducted on the removal of Cu, Pb, and Zn by a commonly used water treatment adsorbent, granular activated carbon (GAC), from three single, three binary (Cu-Pb, Cu-Zn, Pb-Zn), and one ternary (Cu-Pb-Zn) combination of metals. It also investigated seven mathematical models on their suitability to predict the metals adsorption capacities. Adsorption of Cu, Pb, and Zn increased with pH with an abrupt increase in adsorption at around pH 5.5, 4.5, and 6.0, respectively. At all pHs tested (2.5-7.0), the adsorption capacity followed the order Pb > Cu > Zn. The Langmuir and Sips models fitted better than the Freundlich model to the data in the single-metal system at pH 5. The Langmuir maximum adsorption capacities of Pb, Cu, and Zn (mmol/g) obtained from the model's fits were 0.142, 0.094, and 0.058, respectively. The adsorption capacities (mmol/g) for these metals at 0.01 mmol/L equilibrium liquid concentration were 0.130, 0.085, and 0.040, respectively. Ideal Adsorbed Solution (IAS)-Langmuir and IAS-Sips models fitted well to the binary and ternary metals adsorption data, whereas the Extended Langmuir and Extended Sips models' fits to the data were poor. The selectivity of adsorption followed the same order as the metals' capacities and affinities of adsorption in the single-metal systems.

X-ray fluorescence analysis of Pb, Fe and Zn in kohl

Directory of Open Access Journals (Sweden)

Eman Daar

Full Text Available Kohl, a facial salve used in ancient times as a symbol of affluence, now enjoys more widespread traditional followings, for cosmetic, religious and supposed medicinal purposes. Popularly used by women and men of all ages, particularly those of North African, Middle Eastern, Southern Asia, Japanese and Chinese origins, it is also known to be used on neonates and children from such populations. With small-scale producers of kohl possessing a growing awareness of the adverse market impact of products that contain (lead Pb and other toxicity related elements, some claim their products to be Pb-free, offering an apparent change from the more traditional galena-based (lead sulphide media. Among the published physiological effects of exposure to Pb is that it replaces Ca in bones and teeth, making them weak and fragile, other impacts including nephrotoxicity, also linked with increased Pb blood levels in studies in Oman, Canada, Saudi Arabia, India and Pakistan. Current study involves XRF analysis of Pb, Fe and Zn concentrations in 135 samples of kohl from nine randomly selected suppliers (15 samples of each brand being represented. In pursuit of this, use was made of an in-house assembled facility comprising compact high-performance components, the arrangement offering sufficient sensitivity for the purposes of present study. In most of the samples investigated in the present study observation has been made of concentrations of Pb at elevated levels, quantification of those levels also demonstrating a need to address self-attenuation by the Pb itself. Significant concentration of Fe have also been found in several of the samples. Keywords: X-ray florescence, Pb, Fe and Zn contamination, Kohl

Leaching potential of pervious concrete and immobilization of Cu, Pb and Zn using pervious concrete.

Science.gov (United States)

Solpuker, U; Sheets, J; Kim, Y; Schwartz, F W

2014-06-01

This paper investigates the leaching potential of pervious concrete and its capacity for immobilizing Cu, Pb and Zn, which are common contaminants in urban runoff. Batch experiments showed that the leachability of Cu, Pb and Zn increased when pHconcrete might function to attenuate contaminant migration. A porous concrete block was sprayed with low pH water (pH=4.3±0.1) for 190 h. The effluent was highly alkaline (pH~10 to 12). In the first 50 h, specific conductance and trace-metal were high but declined towards steady state values. PHREEQC modeling showed that mixing of interstitial alkaline matrix waters with capillary pore water was required in order to produce the observed water chemistry. The interstitial pore solutions seem responsible for the high pH values and relatively high concentrations of trace metals and major cations in the early stages of the experiment. Finally, pervious concrete was sprayed with a synthetic contaminated urban runoff (10 ppb Cu, Pb and Zn) with a pH of 4.3±0.1 for 135 h. It was found that Pb immobilization was greater than either Cu or Zn. Zn is the most mobile among three and also has the highest variation in the observed degree of immobilization. Copyright © 2014 Elsevier B.V. All rights reserved.

Synthesis of Mn-doped ZnS architectures in ternary solution and their optical properties

Energy Technology Data Exchange (ETDEWEB)

Wang Xinjuan, E-mail: wangxj@hnu.edu.cn [State Key lab of CBSC, Micronano Research Center, Hunan University, Changsha 410082 (China); Zhang Qinglin [State Key lab of CBSC, Micronano Research Center, Hunan University, Changsha 410082 (China); Zou Bingsuo, E-mail: zoubs@bit.edu.cn [State Key lab of CBSC, Micronano Research Center, Hunan University, Changsha 410082 (China); Micro-nano Technology Center and School of MSE, BIT, Beijing 100081 (China); Lei Aihua; Ren Pinyun [State Key lab of CBSC, Micronano Research Center, Hunan University, Changsha 410082 (China)

2011-10-01

Mn-doped ZnS sea urchin-like architectures were fabricated by a one-pot solvothermal route in a ternary solution made of ethylenediamine, ethanolamine and distilled water. The as-prepared products were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and photoluminescence spectra (PL). It was demonstrated that the as-prepared sea urchin-like architectures with diameter of 0.5-1.5 {mu}m were composed of nanorods, possessing a wurtzite structures. The preferred growth orientation of nanorods was found to be the [0 0 2] direction. The PL spectra of the Mn-doped ZnS sea urchin-like architectures show a strong orange emission at 587 nm, indicating the successful doping of Mn{sup 2+} ions into ZnS host. Ethanolamine played the role of oriented-assembly agent in the formation of sea urchin-like architectures. A possible growth mechanism was proposed to explain the formation of sea urchin-like architectures.

Synthesis of Mn-doped ZnS architectures in ternary solution and their optical properties

International Nuclear Information System (INIS)

Wang Xinjuan; Zhang Qinglin; Zou Bingsuo; Lei Aihua; Ren Pinyun

2011-01-01

Mn-doped ZnS sea urchin-like architectures were fabricated by a one-pot solvothermal route in a ternary solution made of ethylenediamine, ethanolamine and distilled water. The as-prepared products were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and photoluminescence spectra (PL). It was demonstrated that the as-prepared sea urchin-like architectures with diameter of 0.5-1.5 μm were composed of nanorods, possessing a wurtzite structures. The preferred growth orientation of nanorods was found to be the [0 0 2] direction. The PL spectra of the Mn-doped ZnS sea urchin-like architectures show a strong orange emission at 587 nm, indicating the successful doping of Mn 2+ ions into ZnS host. Ethanolamine played the role of oriented-assembly agent in the formation of sea urchin-like architectures. A possible growth mechanism was proposed to explain the formation of sea urchin-like architectures.

Distribution and evolution of Zn, Cd, and Pb in Apollo 16 regolith samples and the average U-Pb ages of the parent rocks

Science.gov (United States)

Cirlin, E. H.; Housley, R. M.

1982-01-01

The concentration of surface (low temperature site) and interior (high temperature site) Cd, Zn, and Pb in 13 Apollo 16 highland fines samples, pristine rock 65325, and mare fines sample 75081 were analyzed directly from the thermal release profiles obtained by flameless atomic absorption technique (FLAA). Cd and Zn in pristine ferroan anothosite 65325, anorthositic grains of the most mature fines 65701, and basaltic rock fragments of mare fines 75081 were almost all surface Cd and Zn indicating that most volatiles were deposited on the surfaces of vugs, vesicles and microcracks during the initial cooling process. A considerable amount of interior Cd and Zn was observed in agglutinates. This result suggests that high temperature site interior volatiles originate from entrapment during the lunar maturation processes. Interior Cd found in the most mature fines sample 65701 was only about 15% of the total Cd in the sample. Interior Pb present in Apollo 16 fines samples went up to 60%. From our Cd studies we can assume that this interior Pb in highland fines samples is largely due to the radiogenic decay which occurred after the redistribution of the volatiles took place. We obtained an average age of 4.0 b.y. for the parent rocks of Apollo 16 highland regolith from our interior Pb analyses.

The effect of ultraviolet irradiation on the photothermal, photoluminescence and photoluminescence excitation spectra of Mn-doped ZnS nanoparticles

International Nuclear Information System (INIS)

Briones Cruz, Almira; Shen Qing; Toyoda, Taro

2006-01-01

Research involving Mn doped nanocrystalline ZnS (ZnS:Mn) has grown in recent years, partly due to the high quantum luminescence efficiencies that have been reported. We measured the photoacoustic (PA), the photoluminescence (PL) and the photoluminescence excitation (PLE) spectra of surface-passivated and unpassivated ZnS:Mn. The effects of UV irradiation on the PL and PLE spectra were also studied. A decrease in the PA intensity after UV exposure was observed for the ZnS:Mn, indicating a decrease in the nonradiative relaxation probability. The observed increase in PL intensity indicates a corresponding increase in the radiative transition probability. For the PLE spectra, possible aggregation of the primary particles could have resulted in the lower measured energy of the PLE peak compared to the value predicted by the effective mass approximation theory

Enhanced biocompatibility of ZnS:Mn quantum dots encapsulated with Aloe vera extract for therapeutic applications

International Nuclear Information System (INIS)

Anilkumar, M; Sneha Saj, A; Bindu, K R; Anila, E I

2016-01-01

Toxicity of nanoparticles remains to be a major issue in their application to the biomedical field. Aloe vera (AV) is one of the most widely exploited medicinal plants that have a multitude of amazing properties in the field of medicine. Methanol extract of Aloe vera can be used as a novel stabilising agent for quantum dots to reduce toxicity. We report the synthesis, structural characterization, antibacterial activity and cytotoxicity studies of ZnS:Mn quantum dots synthesized by the colloidal precipitation method, using methanol extract of Aloe vera (AVME) as the capping agent. The ZnS:Mn quantum dots capped with AVME exhibit superior performances in biocompatibility and antibacterial activity compared with ZnS:Mn quantum dots without encapsulation. (paper)

Luminescence mechanisms of organic/inorganic hybrid organic light-emitting devices fabricated utilizing a Zn2SiO4:Mn color-conversion layer

International Nuclear Information System (INIS)

Choo, D.C.; Ahn, S.D.; Jung, H.S.; Kim, T.W.; Lee, J.Y.; Park, J.H.; Kwon, M.S.

2010-01-01

Zn 2 SiO 4 :Mn phosphor layers used in this study were synthesized by using the sol-gel method and printed on the glass substrates by using a vehicle solution and a heating process. Organic/inorganic hybrid organic light-emitting devices (OLEDs) utilizing a Zn 2 SiO 4 :Mn color-conversion layer were fabricated. X-ray diffraction data for the synthesized Zn 2 SiO 4 :Mn phosphor films showed that the Zn ions in the phosphor were substituted into Mn ions. The electroluminescence (EL) spectrum of the deep blue OLEDs showed that a dominant peak at 461 nm appeared. The photoluminescence spectrum for the Zn 2 SiO 4 :Mn phosphor layer by using a 470 nm excitation source showed that a dominant peak at 527 nm appeared, which originated from the 4 T 1 - 6 A 1 transitions of Mn ions. The appearance of the peak around 527 nm of the EL spectra for the OLEDs fabricated utilizing a Zn 2 SiO 4 :Mn phosphor layer demonstrated that the emitted blue color from the deep blue OLEDs was converted into a green color due to the existence of the color-conversion layer. The luminescence mechanisms of organic/inorganic hybrid OLEDs fabricated utilizing a Zn 2 SiO 4 :Mn color-conversion layer are described on the basis of the EL and PL spectra.

Postsynthetic Doping of MnCl2 Molecules into Preformed CsPbBr3 Perovskite Nanocrystals via a Halide Exchange-Driven Cation Exchange.

Science.gov (United States)

Huang, Guangguang; Wang, Chunlei; Xu, Shuhong; Zong, Shenfei; Lu, Ju; Wang, Zhuyuan; Lu, Changgui; Cui, Yiping

2017-08-01

Unlike widely used postsynthetic halide exchange for CsPbX 3 (X is halide) perovskite nanocrystals (NCs), cation exchange of Pb is of a great challenge due to the rigid nature of the Pb cationic sublattice. Actually, cation exchange has more potential for rendering NCs with peculiar properties. Herein, a novel halide exchange-driven cation exchange (HEDCE) strategy is developed to prepare dually emitting Mn-doped CsPb(Cl/Br) 3 NCs via postsynthetic replacement of partial Pb in preformed perovskite NCs. The basic idea for HEDCE is that the partial cation exchange of Pb by Mn has a large probability to occur as a concomitant result for opening the rigid halide octahedron structure around Pb during halide exchange. Compared to traditional ionic exchange, HEDCE is featured by proceeding of halide exchange and cation exchange at the same time and lattice site. The time and space requirements make only MnCl 2 molecules (rather than mixture of Mn and Cl ions) capable of doping into perovskite NCs. This special molecular doping nature results in a series of unusual phenomenon, including long reaction time, core-shell structured mid states with triple emission bands, and dopant molecules composition-dependent doping process. As-prepared dual-emitting Mn-doped CsPb(Cl/Br) 3 NCs are available for ratiometric temperature sensing. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Origin and tectonic implications of the Zhaxikang Pb-Zn-Sb-Ag deposit in northern Himalaya: evidence from structures, Re-Os-Pb-S isotopes, and fluid inclusions

Science.gov (United States)

Zhou, Qing; Li, Wenchang; Qing, Chengshi; Lai, Yang; Li, Yingxu; Liao, Zhenwen; Wu, Jianyang; Wang, Shengwei; Dong, Lei; Tian, Enyuan

2018-04-01

The Zhaxikang Pb-Zn-Sb-Ag-(Au) deposits, located in the eastern part of northern Himalaya, totally contain more than 1.146 million tonnes (Mt) of Pb, 1.407 Mt of Zn, 0.345 Mt of Sb, and 3 kilotonnes (kt) of Ag. Our field observations suggest that these deposits are controlled by N-S trending and west- and steep-dipping normal faults, suggesting a hydrothermal rather than a syngenetic sedimentary origin. The Pb-Zn-Sb-Ag-(Cu-Au) mineralization formed in the Eocene as indicated by a Re-Os isochron age of 43.1 ± 2.5 Ma. Sulfide minerals have varying initial Pb isotopic compositions, with (206Pb/204Pb)i of 19.04-19.68, (207Pb/204Pb)i of 15.75-15.88, and (208Pb/204Pb)i of 39.66-40.31. Sulfur isotopic values display a narrow δ34S interval of +7.8-+12.2‰. These Pb-S isotopic data suggest that the Zhaxikang sources of Pb and S should be mainly from the coeval felsic magmas and partly from the surrounding Mesozoic strata including metasedimentary rocks and layered felsic volcanic rocks. Fluid inclusion studies indicate that the hydrothermal fluids have medium temperatures (200-336 °C) but varying salinities (1.40-18.25 wt.% NaCl equiv.) with densities of 0.75-0.95 g/cm3, possibly suggesting an evolution mixing between a high salinity fluid, perhaps of magmatic origin, with meteoric water.

Cretaceous – Paleogene boundary Fish Clay at Højerup (Stevns Klint, Denmark: Zn, Pb and REE in kerogen

Directory of Open Access Journals (Sweden)

MILOS G. DJORDJEVIC

2008-04-01

Full Text Available Geochemical analyses of Zn, Pb and rare earth elements (La, Ce, Nd, Sm, Eu, Tb, Yb and Lu in the kerogen of the black marl at the Cretaceous – Paleogene boundary Fish Clay at Højerup were performed. Substantial proportions of the Zn, Pb and rare earths were probably contained in terrestrial humic substances (the kerogen precursor arriving at the marine sedimentary site. This is in accord with a previous hypothesis that kerogen is mainly derived from humic acids of an oxic soil in of the adjacent coastal areas of eastern Denmark. It is also suggested that humics enriched in Zn, Pb and rare earth elements were transported mainly through fluvial transport into the deposition site of the Fish Clay. Local weathering/leaching of the impact–eject fallout on the land surface and local terrestrial rocks by impact-induced? acid surface waters perhaps played an important role in providing Zn, Pb and rare earths to these humic substances. Apparently, chondritic and non-chondritic Zn originated from the impact fallout; Pb and rare earth elements were most likely sourced by exposed rocks in the coastal areas of eastern Denmark.

Effect of plant species on the specific activity of 65Zn and 54Mn

International Nuclear Information System (INIS)

Muraoka, T.; Neptune, A.M.L.

1983-01-01

The effect of five plant species on the specific activity of 65 Zn and 54 Mn is studied. Soybean (Glycine max (L.) Merril), bean (Phaseolus vulgaris, L.), rice (Oryza sativa, L.), wheat (Triticum aestivum, L.) and tomato (Lycopersium esculentum Mill) were grown in PV and TE soils labelled with 65 Zn and 54 Mn. The plants were harvested 30 days after seeding and specific activities of zinco and manganese were determined in the above ground part and in the roots. (M.A.C.) [pt

Substrate temperature effects on the structure and properties of ZnMnO films prepared by pulsed laser deposition

Science.gov (United States)

Riascos, H.; Duque, J. S.; Orozco, S.

2017-01-01

ZnMnO thin films were grown on silicon substrates by pulsed laser deposition (PLD). Pulsed Nd:YAG laser was operated at a wavelength of 1064 nm and 100 mJ. ZnMnO thin films were deposited at the vacuum pressure of 10-5 Torr and with substrate temperature from room temperature to 600 °C. The effects of substrate temperature on the structural and Optical properties of ZnMnO thin films have been investigated by X-ray diffraction (XRD), Raman spectroscopy and Uv-vis spectroscopy. From XRD data of the samples, it can be showed that temperature substrate does not change the orientation of ZnMnO thin films. All the films prepared have a hexagonal wurtzite structure, with a dominant (002) peak around 2θ=34.44° and grow mainly along the c-axis orientation. The substrate temperature improved the crystallinity of the deposited films. Uv-vis analysis showed that, the thin films exhibit high transmittance and low absorbance in the visible region. It was found that the energy band to 300 ° C is 3.2 eV, whereas for other temperatures the values were lower. Raman reveals the crystal quality of ZnMnO thin films.

Certification of the contents (mass fractions) of Cd, Pb, Se, Cu, Zn, Fe and Mn in wholemeal flour and lyophilized brown bread reference materials. Wholemeal flour - CRM no. 189; brown bread - CRM no. 191

Energy Technology Data Exchange (ETDEWEB)

Wagstaffe, P J; Griepink, B; Muntau, H; Schramel, P

1987-01-01

The report describes the preparation and certification of a wholemeal flour (CRM 189) and a lyophilised brown breas (CRM 191) for their contents (mass fractions) of elements of toxicological and nutritional importance: Cd, Pb, Se, Cu, Zn, Fe and Mn. Indicative values are also given for As, Ca, Cl, Cr, Hg, Mg, Na, Ni, P and K. Details are given of a preliminary intercomparison of methods for these elements in a wholemeal flour sample, homogeneity and stability studies on the two reference materials and the results and evaluation of the certification exercise which involved 21 European Laboratories. Summaries of the certification methods are also presented. The report concludes with a discussion of the most common sources of error in determining the elements of interest and the steps to be taken to control them. With 7 figs., 28 tabs.

Concentrations, spatial distribution, and risk assessment of soil heavy metals in a Zn-Pb mine district in southern China.

Science.gov (United States)

Qi, Jianying; Zhang, Hailong; Li, Xiangping; Lu, Jian; Zhang, Gaosheng

2016-07-01

China is one of the largest producers and consumers of lead and zinc in the world. Lead and zinc mining and smelting can release hazardous heavy metals such as Cd, Pb, Zn, and As into soils, exerting health risks to human by chronic exposure. The concentrations of Cd, Zn, Pb, and As in soil samples collected from a Pb-Zn mining area with exploitation history of 60 years were investigated. Health risks of the heavy metals in soil were evaluated using US Environmental Protection Agency (US EPA) recommended method. A geo-statistical technique (Kriging) was used for the interpolation of heavy metals pollution and Hazard Index (HI). The results indicated that the long-term Pb/Zn mining activities caused the serious pollution in the local soil. The concentrations of Cd, As, Pb, and Zn in topsoil were 40.3 ± 6.3, 103.7 ± 37.3, 3518.4 ± 896.1, and 10,413 ± 2973.2 mg/kg dry weight, respectively. The spatial distribution of the four metals possessed similar patterns, with higher concentrations around Aayiken (AYK), Maseka (MSK), and Kuangshan (KS) area and more rapidly dropped concentrations at upwind direction than those at downwind direction. The main pollutions of Cd and Zn were found in the upper 60 cm, the Pb was found in the upper 40 cm, and the As was in the upper 20 cm. The mobility of metals in soil profile of study area was classed as Cd > Zn ≫ Pb > As. Results indicated that there was a higher health risk (child higher than adult) in the study area. Pb contributed to the highest Hazard Quotient (57.0 ~ 73.9 %) for the Hazard Index.

Optical and magnetic resonance investigations of Zn{sub 1-} {sub x} Mn {sub x} O magnetic semiconductors

Energy Technology Data Exchange (ETDEWEB)

Zhang Huawei [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Shi Erwei [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Chen Zhizhan [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)]. E-mail: zzchen@mail.sic.ac.cn; Liu Xuechao [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Xiao Bing [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Song Lixin [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

2006-10-15

Zn{sub 1-} {sub x} Mn {sub x} O crystallites were synthesized by hydrothermal method. X-ray diffraction, UV-Vis absorption spectroscopy, and electron paramagnetic resonance (EPR) spectra confirm the substitution of Zn site by Mn{sup 2+} ion. The nonmonotonic variation of band gap exhibits that the short-ranged interactions between the d electrons of Mn and the s and p electrons of the host bands are dominated at lower Mn concentration (x). EPR spectra show that Mn{sup 2+} is in exchange interaction at higher x. By using a Curie-Weiss equation on the EPR data, it is found that the dominant magnetic property is antiferromagnetic for higher x, and paramagnetic for lower x.

Role of microbial inoculation and chitosan in phytoextraction of Cu, Zn, Pb and Cd by Elsholtzia splendens - a field case

Energy Technology Data Exchange (ETDEWEB)

Wang Fayuan [Agricultural College, Henan University of Science and Technology, 70 Tianjin Road, Luoyang, Henan Province 471003 (China) and Institute of Soil Science, Chinese Academy of Sciences, Nanjing, Jiangsu Province 210008 (China)]. E-mail: wfy1975@163.com; Lin Xiangui [Institute of Soil Science, Chinese Academy of Sciences, Nanjing, Jiangsu Province 210008 (China); Yin Rui [Institute of Soil Science, Chinese Academy of Sciences, Nanjing, Jiangsu Province 210008 (China)

2007-05-15

A field experiment was carried out to study the effect of microbial inoculation on heavy metal phytoextraction by Elsholtzia splendens and whether chitosan could have a synergistic effect with the microbial inocula. The microbial inocula consisted of a consortium of arbuscular mycorrhizal fungi and two Penicillium fungi. Three treatments were included: the control, inoculation with microbial inocula, and the inoculation combined with chitosan. Microbial inoculation increased plant biomass especially shoot dry weight, enhanced shoot Cu, Zn and Pb concentrations but did not affect Cd, leading to higher shoot Cu, Zn, Pb and Cd uptake. Compared with microbial inoculation alone, chitosan application did not affect plant growth but increased shoot Zn, Pb and Cd concentrations except Cu, which led to higher phytoextraction efficiencies and partitioning to shoots of Zn, Pb and Cd. These results indicated synergistic effects between microbial inocula and chitosan on Zn, Pb and Cd phytoextraction. - Co-application of microbial inocula and chitosan enhanced heavy metal phytoextraction by E. splendens.

Role of microbial inoculation and chitosan in phytoextraction of Cu, Zn, Pb and Cd by Elsholtzia splendens - a field case

International Nuclear Information System (INIS)

Wang Fayuan; Lin Xiangui; Yin Rui

2007-01-01

A field experiment was carried out to study the effect of microbial inoculation on heavy metal phytoextraction by Elsholtzia splendens and whether chitosan could have a synergistic effect with the microbial inocula. The microbial inocula consisted of a consortium of arbuscular mycorrhizal fungi and two Penicillium fungi. Three treatments were included: the control, inoculation with microbial inocula, and the inoculation combined with chitosan. Microbial inoculation increased plant biomass especially shoot dry weight, enhanced shoot Cu, Zn and Pb concentrations but did not affect Cd, leading to higher shoot Cu, Zn, Pb and Cd uptake. Compared with microbial inoculation alone, chitosan application did not affect plant growth but increased shoot Zn, Pb and Cd concentrations except Cu, which led to higher phytoextraction efficiencies and partitioning to shoots of Zn, Pb and Cd. These results indicated synergistic effects between microbial inocula and chitosan on Zn, Pb and Cd phytoextraction. - Co-application of microbial inocula and chitosan enhanced heavy metal phytoextraction by E. splendens

The giant Upper Yangtze Pb-Zn province in SW China: Reviews, new advances and a new genetic model

Science.gov (United States)

Zhou, Jia-Xi; Xiang, Zhen-Zhong; Zhou, Mei-Fu; Feng, Yue-Xing; Luo, Kai; Huang, Zhi-Long; Wu, Tao

2018-04-01

In the western margin of the Yangtze Block, SW China, the Emeishan large igneous province (ELIP) is spatially associated with >400 carbonate-hosted epigenetic Pb-Zn deposits. These deposits form the giant Upper Yangtze Pb-Zn metallogenic province with >20 Mt base metals. In the southeastern part of this province, the important Pb-Zn deposits include those of the Yinchangpo, Yunluhe, Maozhachang, Tianqiao, Banbanqiao, Mangdong, Shaojiwan, Liangyan, Qingshan, Shanshulin, Nayongzhi and Guanziyao deposits. Sulfide ore bodies in these deposits are (i) hosted in late Ediacaran to middle Permian limestone, dolomitic limestone and dolostone; (ii) structurally controlled by reverse fault-anticline tectonic systems; and (iii) spatially associated with the ELIP flood basalts and mafic dikes, and early Permian, early Carboniferous and early Cambrian organic matter-rich black shales. C-O isotopic compositions suggest that dolostone and limestone, mantle-derived rocks of the ELIP, and sedimentary organic matters supplied C-O to the hydrothermal systems through water/rock (W/R) interaction. New and existing S isotopic compositions of sulfides imply multiple sources of S and the reduction of sulfate through both abiotic thermochemical (TSR) and bacterially mediated (BSR) processes. Zn isotopes indicate that the sources of Zn were most likely related to the ELIP with various contributions from sediments and basements locally. Pb isotope signatures are suggestive of derivation of Pb from basements and sedimentary rocks with variable influences from the ELIP. Sr isotopes support that mantle-derived rocks, sediments and basements were involved in Pb-Zn mineralization, and they have various contributions in different deposits. We consider that the Pb-Zn deposits in the Upper Yangtze province are the mixed products of multiple S species-bearing solutions and metal-rich fluids, both of which were derived from, flowed through or interacted with multiple lithostratigraphic units in the

The peculiarities of electrochemical deposition and morphology of ZnMn alloy coatings obtained from pyrophosphate electrolyte

Directory of Open Access Journals (Sweden)

Bučko Mihael M.

2011-01-01

Full Text Available The first successful attempt to electrodeposit ZnMn alloy coatings from alkaline bath was made only a few years ago. In this kind of solution, potassium pyrophosphate (K4P2O7 serves both as a complexing agent and as the basic electrolyte. The aim of this work was to study the electrodeposition process and properties of ZnMn alloy coatings deposited from pyrophosphate solution, with a new kind of alkaline pyrophosphate bath. Namely, chloride salts were used as the source of metal ions and ascorbic acid was used as reducing agent. The composition of the plating solution was as follows: 1 mol dm-3 K4P2O7 + 0.017 mol dm-3 ascorbic acid + 0.05 mol dm-3 ZnCl2 + 0.05 mol dm-3 MnCl2•4H2O. Cathodic processes during the alloy electrodeposition were investigated using linear voltammetry. The influence of addition of small amounts of ascorbic acid on the cathodic processes was established. It was shown that this substance inhibits hydrogen evolution and increases the current efficiency of alloy deposition. The current efficiency in the plating bath examined was in the range of 25 and 30%, which was quite higher as compared to the results reported in the literature for electrodeposition of ZnMn alloy from pyrophosphate bath. Electrodeposition of ZnMn alloys was performed galvanostatically on steel panels, at current densities of 20120 mA cm-2. The coatings with the best appearance were obtained at current densities between 30 and 80 mA cm-2. The surface morphology studies, based on atomic force microscopy measurements, showed that morphology of the deposits is highly influenced by deposition current density. ZnMn coating deposited at 30 mA cm-2 was more compact and possessed more homogeneous structure (more uniform agglomeration size than the coating deposited at 80 mA cm-2. Such dependence of morphology on the current density could be explained by the high rate of hydrogen evolution reaction during the electrodeposition process.

Optical constants correlated electrons-spin of micro doughnuts of Mn-doped ZnO films

CSIR Research Space (South Africa)

Nkosi, SS

2013-09-01

Full Text Available Diluted magnetic semiconductor (DMS) Mn:ZnO thin films with “ring-like or doughnut-like” structures were grown using aerosol spray pyrolysis for 20 and 30 min. Electron paramagnetic resonance revealed the ferromagnetic ordering which varies with Mn...

Microstructural analysis nanoferritas Mn{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} e Mn{sub 0,65}Zn{sub 0,35}Fe{sub 2}O{sub 4} synthesized by combustion reaction; Analise microestrutural de nanoferritas Mn{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} e Mn{sub 0,65}Zn{sub 0,35}Fe{sub 2}O{sub 4} sintetizadas por reacao de combustao

Energy Technology Data Exchange (ETDEWEB)

Diniz, V.C.S.; Figueiredo, A.R.; Costa Junior, A.D.S.; Diniz, H.M.; Vieira, D.A.; Costa, A.C.F.M., E-mail: veronicacristhina@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais

2014-07-01

The MnZn ferrites are ferrimagnetic materials that have been studied and used in various technological fields. In this work investigated the microstructural characteristics of ferrites and Mn{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} Mn{sub 0,65}Zn{sub 0,35}Fe{sub 2}O{sub 4} synthesized by combustion reaction in 200g scale production. The samples were characterized by XRD, crystallinity, crystallite size, X-ray fluorescence and scanning electron microscopy. Given the results it was observed that for both samples the synthesis combustion reaction was efficient for the production of single-phase ferrites with high crystallinity. With respect to the analysis of X-ray fluorescence was noted that the experimental values composition were consistent with the theoretical values calculated for both samples. Regarding morphology for both samples, the formation of the porous powders with feature consisting of dense clumps in the form of irregular foam was observed. (author)

Piezoelectric properties and temperature stability of Mn-doped Pb(Mg1/3Nb2/3)-PbZrO3-PbTiO3 textured ceramics

Science.gov (United States)

Yan, Yongke; Cho, Kyung-Hoon; Priya, Shashank

2012-03-01

In this letter, we report the electromechanical properties of textured 0.4Pb(Mg1/3Nb2/3)O3-0.25PbZrO3-0.35PbTiO3 (PMN-PZT) composition which has relatively high rhombohedral to tetragonal (R-T) transition temperature (TR-T of 160 °C) and Curie temperature (TC of 234 °C) and explore the effect of Mn-doping on this composition. It was found that MnO2-doped textured PMN-PZT ceramics with 5 vol. % BaTiO3 template (T-5BT) exhibited inferior temperature stability. The coupling factor (k31) of T-5BT ceramic started to degrade from 75 °C while the random counterpart showed a very stable tendency up to 180 °C. This degradation was associated with the "interface region" formed in the vicinity of BT template. MnO2 doped PMN-PZT ceramics textured with 3 vol. % BT and subsequently poled at 140 °C (T-3BT140) exhibited very stable and high k31 (>0.53) in a wide temperature range from room temperature to 130 °C through reduction in the interface region volume. Further, the T-3BT140 ceramic exhibited excellent hard and soft combinatory piezoelectric properties of d33 = 720 pC/N, k31 = 0.53, Qm = 403, tan δ = 0.3% which are very promising for high power and magnetoelectric applications.

The Role of Sedimentation on Waters Edge and Analysis Pb and Zn Concentration in Water from Sentani Lake, Jayapura-Papua

Directory of Open Access Journals (Sweden)

Frans Deminggus

2015-05-01

Full Text Available We have conducted research on the role of sediment on the waters edge and content analysis of metal concentrations of lead (Pb, zinc (Zn in the water of Sentani Lake in Jayapura, Papua Province. The experiment was conducted in April 2013. The study was conducted to determine the role of lake sediments on water quality, sediment characteristics and metal analysis has been analyzed in the laboratory to determine the concentration of Pb and Zn in the sediment. Metal analysis using Atomic Absorption Spectrophotometry (AAS instrumentation. Sediment characteristics that have analysis, namely physical and chemical parameters are bulk density, density, porosity, water content, texture, pH, DO, colors and others. Sediment sampling locations are Ifale, estuary, Yahim beach and Yoboy with each location in depth of 0-5 cm, 5-10 cm and 10-15 cm vertically. The results showed that at each sampling site and every sediment depths showed highly significant influence on the metal content of Pb and Zn. In general, the deeper the sediment content of Pb and Zn showed different results. Average content of heavy metals (Pb and Zn in sediments at each location that are Ifale at 27.37 mg/Kg and 35.04 mg/Kg, estuary of 15.37 mg/Kg and Pb is 28.01 mg/Kg, Yahim beach of 3.83 mg/Kg and 33.50 mg/Kg, while the location of Yoboy of 6.69 mg/Kg and 34.60 mg/Kg. Concentration of Pb (3.83 to 27.37 mg/Kg and Zn (6.69 to 35.04 mg/Kg in sediments is lower than the standard quality of heavy metals in sediments (EPA Region Va is 40 mg/Kg for Pb and 90 mg/Kg for Zn metals, therefore concentrations of Pb and Zn in sediments at four locations of Sentani lake is still below the quality standard so that the levels of Pb and Zn in the sediment is not contaminated. The existence of Sentani lake sediments act as a reservoir heavy metal and not as a source of pollutants to the water quality in the Sentani lake.

Time and temperature dependent breakdown characteristics of ZnS:Mn films obtained by rf-magnetron sputtering

Science.gov (United States)

Zhigal'Skii, A. A.; Mukhachev, V. A.; Troyan, P. E.

1994-04-01

Breakdown delay times (tdel) for films of managanese-doped zinc sulfide (ZnS:Mn) were measured in the range 10-6-10-1 s. The maximum value was tdel=10-3-10-2 s. The electrical strength (Ebr) was found to increase as the voltage pulse duration was reduced, the more so the thinner the ZnS:Mn film. The temperature dependence of Ebr exhibited a weak reduction in Ebr as the temperature was raised to roughly 80°C and a sharp reduction in Ebr for T>130°C. A maximum in Ebr was observed at T≈130°C which is presumably explained by a structural modification of the ZnS:Mn film. The experimental results obtained are explained in terms of a combined electronic and thermal breakdown mechanism.

Synthesis and properties of a new quadruple perovskite: A-site ordered PbMn{sub 3}Mn{sub 4}O{sub 12}

Energy Technology Data Exchange (ETDEWEB)

Locherer, T.; Dinnebier, R.; Kremer, R.K. [Max Planck Institute for Solid State Research, Heisenbergstr. 1, D-70569 Stuttgart (Germany); Greenblatt, M., E-mail: martha@rutchem.rutgers.edu [Department of Chemistry and Chemical Biology, Rutgers University, Piscataway, NJ 08854 (United States); Jansen, M. [Max Planck Institute for Solid State Research, Heisenbergstr. 1, D-70569 Stuttgart (Germany)

2012-06-15

PbMn{sub 3}Mn{sub 4}O{sub 12} a quadruple perovskite was prepared by high pressure and high temperature synthesis. Powder X-ray diffraction (PXD) and differential scanning calorimetry reveal a structural phase transition at {approx}380 K. Rietveld refinement of the synchrotron room temperature data indicate rhombohedral symmetry (R-3) with a=6.43675(4) A and {alpha}=109.556(2) Degree-Sign . Similar 423 K PXD data refined in a body centered cubic cell (Im-3) with a=7.4283(9) A. The temperature variation of magnetization, shows a magnetic field dependent antiferromagnetic-like transition at 68 K, and dynamic fluctuations indicative of magnetic frustration. The semiconducting electrical behavior indicates a large decrease in the conductivity near 68 K. The temperature dependence of the real part of the dielectric constant, {epsilon}{sub real} increases dramatically at {approx}68 K, and shows relaxor-type ferroelectric behavior as a function of frequency. The intimate coupling of magnetic, electrical and dielectric properties at 68 K in PbMn{sub 3}Mn{sub 4}O{sub 12} suggests possible multiferroic behavior. - Graphical abstract: Resistance vs. temperature plot showing drastically increasing resistances at temperatures below 68 K (a). Formation of a frequency dependency of the dielectric constant between 68 K and ambient temperature (b). Sharp cusp in the magnetic susceptibility observed at 68 K which is suppressed with increasing magnetic field (c) indicates coupling of magnetic, electric and dielectric effects. Highlights: Black-Right-Pointing-Pointer PbMn{sub 3}Mn{sub 4}O{sub 12} a quadruple perovskite was prepared at high pressure. Black-Right-Pointing-Pointer A structural transition is seen at 380 K from space group R-3-to-Im-3. Black-Right-Pointing-Pointer An antiferromagnetic transition is observed at 68 K. Black-Right-Pointing-Pointer It is semiconducting with a large decrease in the conductivity near 68 K. Black-Right-Pointing-Pointer The temperature dependence

Hierarchical porous ZnMn{sub 2}O{sub 4} microspheres architectured with sub-nanoparticles as a high performance anode for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Rong, Haibo; Xie, Guiting; Cheng, Si; Zhen, Zihao [New Energy Research Institute, College of Environment and Energy, South China University of Technology, Guangzhou 510006, Guangdong (China); Jiang, Zhongqing [Department of Chemical Engineering, Ningbo University of Technology, Ningbo 315016, Zhejiang (China); Huang, Jianlin; Jiang, Yu; Chen, Bohong [New Energy Research Institute, College of Environment and Energy, South China University of Technology, Guangzhou 510006, Guangdong (China); Jiang, Zhong-Jie, E-mail: zhongjiejiang1978@hotmail.com [New Energy Research Institute, College of Environment and Energy, South China University of Technology, Guangzhou 510006, Guangdong (China)

2016-09-15

A simple two-step procedure, which involves the synthesis of the Zn{sub 0.33}Mn{sub 0.67}CO{sub 3} microspheres through a hydrothermal process and the subsequent calcination, has been used to synthesize the ZnMn{sub 2}O{sub 4} microspheres with a hierarchical porous morphology consisting of the ZnMn{sub 2}O{sub 4} sub-nanoparticles. When evaluated as anode materials for lithium ion batteries (LIBs), these hierarchical porous ZnMn{sub 2}O{sub 4} microspheres could exhibit a stable reversible capability of ∼723.7 mAh g{sup −1} at the current density of 400 mA g{sup −1}, which is much higher than those of the ZnMn{sub 2}O{sub 4} based materials reported previously, indicating the great potential of using them as the anode for the LIBs. This is further supported by their better rate capability and higher cycling stability. Careful analysis has shown that the unique porous structure of the hierarchical porous ZnMn{sub 2}O{sub 4} microspheres which consists of the ZnMn{sub 2}O{sub 4} sub-nanoparticles plays an important role in their higher electrochemical performance, since it allows the accommodation of the volume expansion during the repeated discharge–charge cycles, preventing them from the structural destruction, and increase the accessibility of the electrode material to the Li{sup +} storage, making a better utilization of active materials and an easy diffusion of electrolytes in and out of the electrode material. - Graphical abstract: The ZnMn{sub 2}O{sub 4} microspheres with a hierarchical porous morphology consisting of the ZnMn{sub 2}O{sub 4} sub-nanoparticles have been synthesized by the calcination of the Zn{sub 0.33}Mn{sub 0.67}CO{sub 3} microspheres and could exhibit superior electrochemical performance when used as anode materials for lithium ion batteries. - Highlights: • A simple procedure has been used to synthesize the ZnMn{sub 2}O{sub 4} microspheres. • The ZnMn{sub 2}O{sub 4} microspheres exhibit excellent performance when used in LIBs

Possibilities for reusing the waste from the process of Zn-Pb ore beneficiation

Directory of Open Access Journals (Sweden)

Cichy Krystian

2017-01-01

Full Text Available This paper discusses the areas of storage, resources, and granulometric and chemical characteristics of old Zn-Pb tailings stored in heaps in the city of Bytom area. It presents the results of laboratory tests for development of the technological flowsheet for transformation of the material into Zn- Pb sulfide concentrates and the results of trials in an experimental system of the beneficiation flowsheet which was developed. In the further part of the paper, the results of the research work on preparation of the tailings with reduced metal content for further use are presented.

XPS-and-DFT analyses of the Pb 4f — Zn 3s and Pb 5d — O 2s overlapped ambiguity contributions to the final electronic structure of bulk and thin-film Pb-modulated zincite

Energy Technology Data Exchange (ETDEWEB)

Zatsepin, D.A. [M.N. Miheev Institute of Metal Physics of Ural Branch of Russian Academy of Sciences, 620990 Yekaterinburg (Russian Federation); Institute of Physics and Technology, Ural Federal University, 620002 Yekaterinburg (Russian Federation); Boukhvalov, D.W., E-mail: danil@hanyang.ac.kr [Department of Chemistry, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Theoretical Physics and Applied Mathematics Department, Ural Federal University,Mira Street 19, 620002 Yekaterinburg (Russian Federation); Gavrilov, N.V. [Institute of Electrophysics, Russian Academy of Sciences, Ural Branch, 620990 Yekaterinburg (Russian Federation); Kurmaev, E.Z. [M.N. Miheev Institute of Metal Physics of Ural Branch of Russian Academy of Sciences, 620990 Yekaterinburg (Russian Federation); Institute of Physics and Technology, Ural Federal University, 620002 Yekaterinburg (Russian Federation); Zatsepin, A.F. [Institute of Physics and Technology, Ural Federal University, 620002 Yekaterinburg (Russian Federation); Cui, L. [Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen 518055 (China); Shur, V. Ya.; Esin, A.A. [Institute of Natural Sciences, Ural Federal University, 51 Lenin Ave, 620000 Yekaterinburg (Russian Federation)

2017-05-31

Highlights: • Two modes of ZnO:Pb in the bulk and surface morphologies were established: the high- and low-interaction. • It was shown the ambiguity contribution of Pb 4f − Zn 3s and Pb 5d − O 2s states into final electronic structure. • The main type of defects is PbO-like with some PbO{sub 2}-like contributions. • An applied wurzite-like structural model well agrees with experimental data obtained for zincite. - Abstract: The electronic structures of zincite Pb-modulated bulk and thin-films were studied via X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) techniques. Both XPS data and DFT-calculations allowed the derivation of two different Pb-embedding scenarios into the ZnO-hosts. These included the high-interaction mode of Pb-impurity with initial zinc-oxygen host-lattice for the bulk morphology, accompanied with low Pb-metal losses; and the low-interaction mode for thin-films, where there was intake of Pb-impurities into the hollows of the surface. Despite dissimilar mechanisms of Pb-impurity accumulation and distribution in the bulk and thin-films zincite host-matrices, the strong Pb 4f — Zn 3s and Pb 5d — O 2s overlapped ambiguity contribution to the appropriate core-level structure and valence bands was established by XPS analysis and reproduced with the help of DFT-calculations. It was shown that the microscopic structure of the embedded lead-impurity played a crucial role in the Pb ion-beam stimulated synthesis of secondary lead-oxygen phases via large-area defect fabrication, and the difference among zincite and wurzite polymorphs played almost no role in this case.

Pathways of Pb and Mn observed in a 5-year longitudinal investigation in young children and environmental measures from an urban setting.

Science.gov (United States)

Gulson, Brian; Mizon, Karen; Taylor, Alan; Korsch, Michael; Davis, J Michael; Louie, Honway; Wu, Michael; Gomez, Laura; Antin, Luminita

2014-08-01

We monitored 108 children ≤5 years on a 6-month basis for up to 5 years in a major urban setting. Samples (n ∼ 7000) included blood, urine, handwipes (interior, and after exterior playing), 6-day duplicate diet, drinking water, interior house and day care dust-fall accumulation using petri dishes, exterior dust-fall accumulation, exterior dust sweepings, paint, soil and urban air. The geometric mean blood Pb (PbB) was 2.1 μg/dL and blood Mn (MnB) was 10.0 μg/L. Following a path modelling approach, mixed model analyses for a fully adjusted model showed the strongest associations for PbB were with interior house dust and soil; for MnB there were no significant associations with any predictors. Predictor variables only explained 9% of the variance for Pb and 0.7% for Mn. Relationships between environmental measures and PbB in children are not straightforward; soil and dust sweepings contribute only about 1/5th of the amounts to PbB found in other studies. Copyright © 2014 Elsevier Ltd. All rights reserved.

Synthesis, Magnetization, and Electrical Transport Properties of Mn3Zn0.9Cu0.1N

Directory of Open Access Journals (Sweden)

Y. Yin

2013-01-01

Full Text Available We synthesized Mn3Zn0.9Cu0.1N by solid state reaction, and magnetic as well as electrical transport properties were investigated. It is found that Mn3Zn0.9Cu0.1N exhibits a first-order antiferromagnetism (AFM to paramagnetic (PM transition with the Néel temperature TN ~163 K, and substitution of Cu for Zn would favor ferromagnetism (FM state and weaken AFM ground state, leading to a convex curvature character of M(T curve. With high external fields 10 kOe–50 kOe, magnetic transition remains a robust AFM-PM feature while FM phase is completely suppressed. Thermal hysteresis of M(T under 500 Oe is also suppressed when the magnetic field exceeds 10 kOe. Mn3Zn0.9Cu0.1N exhibits a good metallic behavior except for a slope change around TN, which is closely related to AFM-PM magnetic transition. Compared with the first differential of resistivity with respect to temperature for (dρ/dTMn3ZnN in transition temperature range, the absolute value of (dρ/dTMn3Zn0.9Cu0.1N is much lower which is close to zero.

Oriented Attachment Is a Major Control Mechanism To Form Nail-like Mn-Doped ZnO Nanocrystals.

Science.gov (United States)

Patterson, Samuel; Arora, Priyanka; Price, Paige; Dittmar, Jasper W; Das, Vijay Kumar; Pink, Maren; Stein, Barry; Morgan, David Gene; Losovyj, Yaroslav; Koczkur, Kallum M; Skrabalak, Sara E; Bronstein, Lyudmila M

2017-12-26

Here, we present a controlled synthesis of Mn-doped ZnO nanoparticles (NPs) with predominantly nail-like shapes, whose formation occurs via tip-to-base-oriented attachment of initially formed nanopyramids, followed by leveling of sharp edges that lead to smooth single-crystalline "nails". This shape is prevalent in noncoordinating solvents such as octadecene and octadecane. Yet, the double bond in the former promotes oriented attachment. By contrast, Mn-doped ZnO NP synthesis in a weakly coordinating solvent, benzyl ether, results in dendritic structures because of random attachment of initial NPs. Mn-doped ZnO NPs possess a hexagonal wurtzite structure, and in the majority of cases, the NP surface is enriched with Mn, indicating a migration of Mn 2+ ions to the NP surface during the NP formation. When the NP formation is carried out without the addition of octadecyl alcohol, which serves as a surfactant and a reaction initiator, large, concave pyramid dimers are formed whose attachment takes place via basal planes. UV-vis and photoluminescence spectra of these NPs confirm the utility of controlling the NP shape to tune electro-optical properties.

Lethal critical body residues as measures of Cd, Pb, and Zn bioavailability and toxicity in the earthworm Eisenia fetida

Energy Technology Data Exchange (ETDEWEB)

Conder, J.M.; Lanno, R.P. [Oklahoma State Univ., Dept. of Zoology, Stillwater, OK (United States)

2003-07-01

Background. Earthworm heavy metal concentrations (critical body residues, CBRs) may be the most relevant measures of heavy metal bioavailability in soils and may be linkable to toxic effects in order to better assess soil ecotoxicity. However, as earthworms possess physiological mechanisms to secrete and/or sequester absorbed metals as toxicologically inactive forms, total earthworm metal concentrations may not relate well with toxicity. Objective. The objectives of this research were to: i) develop LD{sub 50}s (total earthworm metal concentration associated with 50% mortality) for Cd, Pb, and Zn; ii) evaluate the LD{sub 50} for Zn in a lethal Zn-smelter soil; iii) evaluate the lethal mixture toxicity of Cd, Pb, and Zn using earthworm metal concentrations and the toxic unit (TU) approach; and iv) evaluate total and fractionated earthworm concentrations as indicators of sublethal exposure. Methods. Earthworms (Eisenia fetida (Savigny)) were exposed to artificial soils spiked with Cd, Pb, Zn, and a Cd-Pb-Zn equitoxic mixture to estimate lethal CBRs and mixture toxicity. To evaluate the CBR developed for Zn, earthworms were also exposed to Zn-contaminated field soils receiving three different remediation treatments. Earthworm metal concentrations were measured using a procedure devised to isolate toxicologically active metal burdens via separation into cytosolic and pellet fractions. (orig.)

Metal and metalloid contamination in roadside soil and wild rats around a Pb-Zn mine in Kabwe, Zambia

Energy Technology Data Exchange (ETDEWEB)

Nakayama, Shouta M.M.; Ikenaka, Yoshinori; Hamada, Kyohei [Laboratory of Toxicology, Department of Environmental Veterinary Sciences, Graduate School of Veterinary Medicine, Hokkaido University, Kita 18, Nishi 9, Kita-ku, Sapporo 060-0818 (Japan); Muzandu, Kaampwe; Choongo, Kennedy [Department of Biomedical Studies, School of Veterinary Medicine, University of Zambia, P.O. Box 32379, Lusaka (Zambia); Teraoka, Hiroki; Mizuno, Naoharu [Department of Toxicology, School of Veterinary Medicine, Rakuno Gakuen University, Ebetsu 069-8501 (Japan); Ishizuka, Mayumi, E-mail: ishizum@vetmed.hokudai.ac.j [Laboratory of Toxicology, Department of Environmental Veterinary Sciences, Graduate School of Veterinary Medicine, Hokkaido University, Kita 18, Nishi 9, Kita-ku, Sapporo 060-0818 (Japan)

2011-01-15

Metal (Cr, Co, Cu, Zn, Cd, Pb, Ni) and metalloid (As) accumulation was studied in roadside soil and wild rat (Rattus sp.) samples from near a Pb-Zn mine (Kabwe, Zambia) and the capital city of Zambia (Lusaka). The concentrations of the seven metals and As in the soil samples and Pb in the rat tissue samples were quantified using atomic absorption spectroscopy. The concentrations of Pb, Zn, Cu, Cd, and As in Kabwe soil were much higher than benchmark values. Geographic Information System analysis indicated the source of metal pollution was mining and smelting activity. Interestingly, the area south of the mine was more highly contaminated even though the prevailing wind flow was westward. Wild rats from Kabwe had much higher tissue concentrations of Pb than those from Lusaka. Their body weight and renal Pb levels were negatively correlated, which suggests that mining activity might affect terrestrial animals in Kabwe. - The area around Kabwe, Zambia is highly polluted with metals and As. Wild rats from this area had high tissue concentrations of Pb and decreased body weight.

Study of Zn-Pb ore tailings and their potential in cement technology

Science.gov (United States)

Nouairi, J.; Hajjaji, W.; Costa, C. S.; Senff, L.; Patinha, C.; Ferreira da Silva, E.; Labrincha, J. A.; Rocha, F.; Medhioub, M.

2018-03-01

This paper describes the synthesis of sulfobelite clinkers incorporating mining rejects. The targeted Zn-Pb tailing wastes generated in the diapiric zone (NW Tunisia) were tested in clinker/cement compositions to ensure the inertization of existing hazardous heavy metals. Mineralogical composition of the two selected samples revealed calcite, dolomite, quartz, kaolinite, galena, pyrite and gypsum as crystalline phases. Vertical distributions of dominant heavy metals (Pb, Zn and Cu) in soil profiles show enrichment in the surface layers and decrease towards the depth. In sintered clinkers powders, the presence of the targeted crystalline phases (trialuminate sulphate (C4A3Š), belite (C2S), and ferrite (C4AF)) are in the predicted desirable amounts. Heat flow generated during the hydration of different cement pastes showed a slower reaction for clinkers with higher amounts of C4A3Š or constituted by coarser particles. After 28 days curing, the best mechanical resistance (24.34 MPa under compression) was obtained for the clinker calcined at 1350 °C and showing a suitable particle size distribution. Concerning heavy metals, immobilisation of 75-85% of Pb, Zn and Cu was assessed in the mortars formulated with the produced clinker/cement, posing no hazardous risks to the environment.

Damage annealing in low temperature Fe/Mn implanted ZnO

International Nuclear Information System (INIS)

Gunnlaugsson, H. P.; Bharuth-Ram, K.; Johnston, K.; Langouche, G.; Mantovan, R.; Mølholt, T. E.; Naidoo, D.; Ólafsson, O.; Weyer, G.

2015-01-01

57 Fe Emission Mössbauer spectra obtained after low fluence (<10 12 cm −2 ) implantation of 57 Mn (T 1/2 = 1.5 min.) into ZnO single crystal held at temperatures below room temperature (RT) are presented. The spectra can be analysed in terms of four components due to Fe 2+ and Fe 3+ on Zn sites, interstitial Fe and Fe in damage regions (Fe D ). The Fe D component is found to be indistinguishable from similar component observed in emission Mössbauer spectra of higher fluence (∼10 15 cm −2 ) 57 Fe/ 57 Co implanted ZnO and 57 Fe implanted ZnO, demonstrating that the nature of the damage regions in the two types of experiments is similar. The defect component observed in the low temperature regime was found to anneal below RT

Formation of stable and metastable phases in reciprocal systems PbSe + MI2 = MSe + PbI2 (M = Hg, Mn, Sn)

International Nuclear Information System (INIS)

Odin, I.N.; Grin'ko, V.V.; Kozlovskij, V.F.; Safronov, E.V.; Gapanovich, M.V.

2004-01-01

Using data of differential thermal, X-ray phase and microstructural analyses, phase diagrams of reciprocal systems PbSe + MI 2 = MSe + PbI 2 (M=Hg (1), Mn (2), Sn (3)) were constructed. It was ascertained that the HgSe-PbI 2 diagonal in system 1 is stable. Transformations leading to crystallization of metastable ternary compound formed in the system PbSe-PbI 2 and metastable polytypes of lead iodide in systems 1 and 2 in the range of temperatures from 620 to 685 K were studied. New intermediate metastable phases in systems 1, 2 and 3 were prepared by melt quenching. Crystal lattice parameters of the phases crystallizing in the CdCl 2 structural type were defined [ru

Quantitative microanalysis of Mn, Zn and other elements in mature wheat seed

International Nuclear Information System (INIS)

Mazzolini, A.P.; Pallaghy, C.K.; Legge, G.J.F.

1984-01-01

A scanning proton microprobe has been used to determine quantitatively the distribution of Mn,Zn and other elements in the mature wheat seed. Both X-ray and nuclear scattered proton data were collected during the irradiation of a 40 μ-thick longitudinal section, and these were used to calculate absolute elemental concentrations for the various features of interest in the embryo region. In the embryo, Mn was highest in the radicle (1400 +- 200 ppm) and lowest in the coleorhiza (200 +- 30 ppm), whereas Zn was highest in the scutellum (600 +- 100 ppm) and lowest in the leaf primordium (410 +- 70 ppm). Comparisons with direct bulk chemical analysis of excised embryos showed agreement. The possible biological significance of the distribution of elements is discussed

Doping of ZnO with Mn or Co: Two different behaviours for the same synthesis approach

Directory of Open Access Journals (Sweden)

Peiteado, M.

2010-02-01

Full Text Available In the last years the research in ZnO has seen a period of intensive work which can be attributed to the new available synthesis methods and characterization techniques. New potential applications have thus emerged for ZnO-based ceramics, provided that a stable and reproducible doping would be achieved. However this still represents a major challenge. In this new trend, Mn and Co represent a couple of interesting candidates for the obtaining of new ZnO-doped structures. But although a lot of work has been done in the past with both systems, a detailed analysis of the specialized literature yet reveals a worrisome lack of knowledge about these materials. In the present contribution the diffusion behavior and the solid state reactivity of both Zn-Mn-O and Zn-Co-O systems is analyzed in order to determine the possibility of obtaining a homogeneous doping of ZnO. The obtained results indicate that, whereas a stable Co:ZnO solid solution is easily attainable, the achievement of a homogeneous Mn:ZnO solid solution would be restricted to severe experimental conditions that limit its application for practical purposes.

En los últimos años, la investigación entorno al ZnO ha experimentado un periodo de intensa labor que bien puede atribuirse a los nuevos métodos de síntesis y a las nuevas técnicas de caracterización disponibles. En consecuencia han surgido nuevas aplicaciones potenciales para los materiales basados en ZnO, siempre y cuando se alcance un dopado estable y reproducible del cerámico. Sin embargo, esto es algo que todavía supone un serio reto. Dentro de esta nueva tendencia, el Mn y el Co representan un par de candidatos interesantes para la obtención de nuevas estructuras de ZnO dopado. Sin embargo, aunque se ha trabajado con ambos sistemas desde hace bastante tiempo, lo cierto es que un análisis detallado de la literatura especializada de los últimos años todavía revela un serio desconocimiento entorno a dichos

Crystal structure, energy transfer and tunable luminescence properties of Ca8ZnCe(PO4)7:Eu2+,Mn2+ phosphor

Science.gov (United States)

Ding, Chong; Tang, Wanjun

2018-02-01

Single-phased Ca8ZnCe(PO4)7:Eu2+,Mn2+ phosphors with whitlockite-type structure have been prepared via the combustion-assisted synthesis technique. The XRD pattern show that the as-obtained phosphors crystallize in a trigonal phase with space group of R-3c (161). Ca8ZnCe(PO4)7 host is full of sensitizers (Ce3+) and the Ce3+ emission at different lattice sites has been discussed. The efficient energy transfers from Ce3+ ions to Eu2+/Mn2+ ions and from Eu2+ to Mn2+ have been validated. Under UV excitation, the emitting color of Ca8ZnCe(PO4)7:Eu2+/Mn2+ samples can be modulated from violet blue to green and from violet blue to red-orange by the energy transfers of Ce3+→Eu2+ and Ce3+→Mn2+, respectively. Additionally, white emission has been obtained through adjusting the relative concentrations of Eu2+ and Mn2+ ions in the Ca8ZnCe(PO4)7 host under UV excitation. These results indicate that as-prepared Ca8ZnCe(PO4)7:Eu2+,Mn2+ may be a potential candidate as color-tunable white light-emitting phosphors.

Influence of mechanical activation on the leaching of non-ferrous metals from a CuPbZn complex concentrate

Directory of Open Access Journals (Sweden)

Godoèíková Erika

2000-09-01

Full Text Available The aim of study was to research the procedures of copper, lead and zinc leaching from CuPbZn complex sulphide concentrate during the intervention of mechanical activation.Mechanical activation belongs to innovative procedures, which intensifies technological processes by means of creation of new surfaces and making defective structure of solid phase. Mechanical impact on the solid phase is a suitable procedure to ensure the mobility of its structure elements and to accumulate the mechanical energy that is later used in following processes of leaching.This paper deals with the intensification of the chloride and thiourea leaching of copper, lead and zinc from a CuPbZn complex concentrate of Hodruša-Hámre (Slovak deposit by using the mechanical activation in an attritor. Ferric chloride and thiourea were used as leaching reagents. The leaching of the concentrate with ferric chloride solution afforded 23 % recovery of Cu, 99 % of Pb and 28 % of Zn. 9 % recovery of Cu, 17 % of Pb and 3 % of Zn were achieved by the leaching with thiourea. Thus results showed that the extraction of Cu, Zn and also Pb in the case of thiourea leaching was low. The use of milling in the attritor as an innovation method of pretreatment leads to the structural degradation and increasing the surface area of the investigated concentrate from the original value of 0.18 m2g-1 to the maximum value of 4.67 m2g-1. This fact manifested itself in the subsequent process of extraction of Cu, Pb and Zn into the chloride and thiourea solutions. Our results indicate more effective leaching of pretreated concentrate in the chloride medium with recoveries of 84 % Zn and 100 % Pb. In thiourea, the recoveries for Zn and Pb were low, however 99 % Cu can be recovered. In regard to the economy, the extraction of Cu, Pb and Zn was studied in this work with the aspect of minimal energy consumption during milling. The maximum recoveries of non-ferrous metals in the solutions of ferric chloride

Factors influencing the Zn and Mn extraction from pyrometallurgical sludge in the steel manufacturing industry.

Science.gov (United States)

Mocellin, J; Mercier, G; Morel, J L; Blais, J F; Simonnot, M O

2015-08-01

In this laboratory study, a process has been developed for selectively leaching zinc and manganese from pyrometallurgical sludge produced in the steel manufacturing industry. In the first part, the yield of Zn extraction was studied using four factors and four levels of the Box-Behnken response surface design. The optimum conditions for the step of Zn leaching were determined to be a sulfuric acid concentration of 0.25 mol/L, a pulp density of 10%, an extraction temperature of 20 °C, and three stages of leaching. Under such conditions, 75% of the Zn should be leached. For Mn leaching, the optimum conditions were determined to be a sulfuric acid concentration of 0.25 mol/L, a Na2S2O5/Mn stoichiometry of 1, a leaching time of 120 min and two leaching steps. In this case, 100% of the Mn should be leached. Copyright © 2015 Elsevier Ltd. All rights reserved.

Relation Between pH and Desorption of Cu, Cr, Zn, and Pb from Industrially Polluted Soils

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Hansen, Henrik K.; Jensen, Pernille Erland

2009-01-01

Desorption of Cu, Cr, Pb, and Zn from industrially polluted soils as a result of acidification is in focus. The eight soils of the investigation vary greatly in composition and heavy metal concentration/combination. Three soils had elevated concentrations of Cu, Pb, and Zn; regardless of pollution...... level, pollution origin, and soil type, the order for desorption as pH decreased was Zn > Cu > Pb. Turning to a single heavy metal in different soils, there was a huge difference in the pH at which the major desorption started. The variation was most significant for Pb where, e.g., less than 10......% was desorbed at pH 2.5 from one soil, whereas in another soil 60% Pb was desorbed at this pH. Sequential extraction was made and the soils in which a high percentage of Pb was found in the residual phase (adsorbed strongest) was also the soils where less Pb was desorbed at low pH in the desorption experiments...

Enhanced biocompatibility of ZnS:Mn quantum dots encapsulated with Aloe vera extract for therapeutic applications

Science.gov (United States)

Anilkumar, M.; Bindu, K. R.; Sneha Saj, A.; Anila, E. I.

2016-08-01

Toxicity of nanoparticles remains to be a major issue in their application to the biomedical field. Aloe vera (AV) is one of the most widely exploited medicinal plants that have a multitude of amazing properties in the field of medicine. Methanol extract of Aloe vera can be used as a novel stabilising agent for quantum dots to reduce toxicity. We report the synthesis, structural characterization, antibacterial activity and cytotoxicity studies of ZnS:Mn quantum dots synthesized by the colloidal precipitation method, using methanol extract of Aloe vera (AVME) as the capping agent. The ZnS:Mn quantum dots capped with AVME exhibit superior performances in biocompatibility and antibacterial activity compared with ZnS:Mn quantum dots without encapsulation. Project supported by the Science and Engineering Research Board (SERB), Department of Science and Technology (DST), Government of India.

Lead Isotopic Compositions of Selected Coals, Pb/Zn Ores and Fuels in China and the Application for Source Tracing.

Science.gov (United States)

Bi, Xiang-Yang; Li, Zhong-Gen; Wang, Shu-Xiao; Zhang, Lei; Xu, Rui; Liu, Jin-Ling; Yang, Hong-Mei; Guo, Ming-Zhi

2017-11-21

Lead (Pb) pollution emission from China is becoming a potential worldwide threat. Pb isotopic composition analysis is a useful tool to accurately trace the Pb sources of aerosols in atmosphere. In this study, a comprehensive data set of Pb isotopes for coals, Pb/Zn ores, and fuels from China was presented. The ratios of 206 Pb/ 207 Pb and 208 Pb/ 206 Pb in the coals were in the range of 1.114-1.383 and 1.791-2.317, similar to those from Europe, Oceania, and South Asia, but different from those from America (p fuels from in coals. Urban aerosols demonstrated similar Pb isotopic compositions to coals, Pb/Zn ores, and fuels in China. After removing the leaded gasoline, the Pb in aerosols is more radiogenic, supporting the heavy contribution of coal combustion to the atmospheric Pb pollution.

The Influence of Pb and Zn Contaminated soil on the Germination ...

African Journals Online (AJOL)

ADOWIE PERE

www.bioline.org.br/ja. The Influence of Pb and Zn Contaminated soil on the Germination and Growth of ... of the periodic table such as aluminium, cadmium, zinc, chromium, copper ..... Remediation Division Robert S. Kerr. Environmental ...

Structural and optical characterization of Mn doped ZnS nanocrystals elaborated by ion implantation in SiO2

International Nuclear Information System (INIS)

Bonafos, C.; Garrido, B.; Lopez, M.; Romano-Rodriguez, A.; Gonzalez-Varona, O.; Perez-Rodriguez, A.; Morante, J.R.; Rodriguez, R.

1999-01-01

Mn doped ZnS nanocrystals have been formed in SiO 2 layers by ion implantation and thermal annealing. The structural analysis of the processed samples has been performed mainly by Secondary Ion Mass Spectroscopy (SIMS) and Transmission Electron Microscopy (TEM). The data show the precipitation of ZnS nanocrystals self-organized into two layers parallel to the free surface. First results of the optical analysis of samples co-implanted with Mn show the presence of a yellow-green photoluminescence depending on the Mn concentration and the size of the nanocrystals, suggesting the doping with Mn of some precipitates

Effect of Si, Mn, Sn on Tensile and Corrosion Properties of Mg-4Zn-0.5Ca Alloys for Biodegradable Implant Materials

Energy Technology Data Exchange (ETDEWEB)

Cho, Dae Hyun; Nam, Ji Hoon; Lee, Byeong Woo; Park, Ji Yong; Shin, Hyun Jung; Park, Ik Min [Pusan National University, Busan (Korea, Republic of)

2015-03-15

Effect of elements Si, Mn, Sn on tensile and corrosion properties of Mg-4Zn-0.5Ca alloys were investigated. The results of tensile properties show that the yield strength, ultimate tensile strength and elongation of Mg-4Zn-0.5Ca alloy increased significantly with the addition of 0.6 wt% Mn. This is considered the grain refinement effect due to addition of Mn. However addition of 0.6 wt% Si decreased yield strength, ultimate tensile strength and elongation. The bio-corrosion behavior of Mg-4Zn-0.5Ca-X alloys were investigated using immersion tests and potentiodynamic polarization test in Hank's solution. Immersion test showed that corrosion rate of Mg-4Zn-0.5Ca-0.6Mn alloy was the lowest rate and addition of 1.0 wt% Sn accelerated corrosion rate due to micro-galvanic effect in α-Mg/CaMgSn phases interface. And corrosion potential (E{sub c}orr) of Mg-4Zn-0.5Ca-0.6Mn alloy was the most noble among Mg-4Zn-0.5Ca-X alloys.

Role of additives; sodium dodecyl sulphate and manganese chloride on morphology of Zn{sub 1−x}Mn{sub x}O nanoparticles and their photoluminescence properties

Energy Technology Data Exchange (ETDEWEB)

Pandey, Gajanan, E-mail: pandeygajanan@rediffmail.com [Department of Applied Chemistry, Babasaheb Bhimrao Ambedkar University, Lucknow 226025, U.P. (India); Dixit, Supriya; Shrivastava, A.K. [School of Studies in Physics, Jiwaji University, Gwalior 474011, M.P. (India)

2014-10-15

In the present study Zn{sub 1−x}Mn{sub x}O (x = 0, 0.05 and 0.1) nanoparticles (NPs) have been synthesised in aqueous solution phase at mild reaction temperature 100 °C in moderate alkaline medium (pH = 9.5), and the role of external additives; like sodium dodecyl sulphate and manganese chloride on the morphology and size of the products has been explored on the basis of transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectral analyses data. ZnO hexagonal nano-plates, core–shell like spherical/ellipsoidal Zn{sub 0.95}Mn{sub 0.05}O structures and thin sheets, thorn/needle mixed shaped Zn{sub 0.9}Mn{sub 0.1}O structures have been observed in TEM and SEM images. Zn(OH){sub 2} formed in moderate alkaline medium, converted to Zn(II) hydroxo complex ions on dissolution, which further recrystallizes to produce wurtzite ZnO at 100 °C. From XRD and EDX analysis, successful doping of Mn{sup 2+} ions at the Zn{sup 2+} sites in ZnO host has been proved. In the photoluminescence spectra, the observed blue shifts in NBE peaks and decrease of emissions intensity on Mn doping have thoroughly been discussed in the present investigation. - Highlights: • Zn{sub 1−x}Mn{sub x}O NPs have been prepared in aqueous solution at mild temperature 100 °C. • Shifts in XRD lines and NBE peaks in PL spectra proved doping of Mn{sup 2+} in the ZnO. • ZnO is formed via dissolution–recrystallization of ε-Zn(OH){sub 2}–ZnO. • Additives SDS and MnCl{sub 2}·4H{sub 2}O play important role on morphology of Zn{sub 1−x}Mn{sub x}O NPs. • Mn contents increased extrinsic defects, which decreased intensity of PL spectra.

Synthesis and Luminescence Properties of Yellow-emitting SiO2/Zn2SiO4: Mn Nanocomposite

Directory of Open Access Journals (Sweden)

Karim OMRI

2014-05-01

Full Text Available Yellow light emitting Mn2+-doped b-Zn2SiO4 phosphor nanoparticles embedded in SiO2 host matrix, were prepared by a simple solid-phase reaction under natural atmosphere at 1500 °C for 2 hours after the incorporation of manganese doped zinc oxide nanoparticles in silica using sol-gel method. The SiO2/Zn2SiO4:Mn nanocomposite was characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, scanning electron microscopy (SEM and photoluminescence (PL. The nanopowder was crystallized in triclinic b-Zn2SiO4 phase with a particles size varies between 70 nm and 84 nm. The SiO2/b-Zn2SiO4:Mn nanocomposite exhibited a broad yellow emission band at 575 nm under UV excitation light. The dependence of the intensity and energy position of the obtained PL band on measurement temperature and power excitation will be discussed.

Enhancement of efficiency by embedding ZnS and Mn-doped ZnS nanoparticles in P3HT:PCBM hybrid solid state solar cells

Science.gov (United States)

Jabeen, Uzma; Adhikari, Tham; Shah, Syed Mujtaba; Nunzi, Jean-Michel; Badshah, Amin; Ahmad, Iqbal

2017-06-01

Zinc sulphide (ZnS) and Mn-doped ZnS nanoparticles were synthesized by wet chemical method. The synthesized nanoparticles were characterized by UV-visible, fluorescence, X-ray diffraction (XRD), fourier transform infra-red (FTIR) spectrometer, field emission scanning electron microscope (FESEM) and high resolution transmission electron microscope (HRTEM). Scanning electron microscope (SEM) was used to find particle size while chemical composition of the synthesized materials was investigated by EDAX. UV-visible absorption spectrum of Mn-doped ZnS was slightly shifted to lower wavelength with respect to the un-doped zinc sulphide with decrease in the size of nanoparticles. Consequently, the band gap was tuned from 3.04 to 3.13 eV. The photoluminescence (PL) emission positioned at 597 nm was ascribed to 4T1 → 6A1 transition within the 3d shell of Mn2+. X-ray diffraction (XRD) analysis revealed that the synthesized nanomaterials existed in cubic crystalline state. The effect of embedding un-doped and doped ZnS nanoparticles in the active layer and changing the ratio of PCBM ([6, 6]-phenyl-C61-butyric acid methyl ester) to nanoparticles on the performance of hybrid solar cell was studied. The device with active layer consisting of poly(3-hexylthiophene) (P3HT), [6, 6]-phenyl-C61-butyric acid methyl ester (PCBM), and un-doped ZnS nanoparticles combined in the ratio of (1:0.5:0.5) attained an efficiency of 2.42% which was found 71% higher than the reference device under the same conditions but not containing nanoparticles. Replacing ZnS nanoparticles with Mn-doped ZnS had a little effect on the enhancement of efficiency. The packing behavior and morphology of blend of nanoparticles with P3HT:PCBM were examined using atomic force microscope (AFM) and XRD. Contribution to the topical issue "Materials for Energy harvesting, conversion and storage II (ICOME 2016)", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

Measurement of the valence band-offset in a PbSe/ZnO heterojunction by x-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Li Lin; Qiu Jijun; Weng Binbin; Yuan Zijian; Shi Zhisheng [School of Electrical and Computer Engineering, University of Oklahoma, Norman, Oklahoma 73019 (United States); Li Xiaomin; Gan Xiaoyan [State Key Laboratory of High Performance Ceramics and Superfine Microstructures, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Sellers, Ian R. [Deparment of Physics, University of Oklahoma, Norman, Oklahoma 73019 (United States)