A comparative approach to synthesis and sintering of alumina/yttria nanocomposite powders using different precipitants

Energy Technology Data Exchange (ETDEWEB)

Kafili, G. [Department of Nanotechnology Engineering, Faculty of Advanced Sciences and Technologies, University of Isfahan, Isfahan, 81746-73441 (Iran, Islamic Republic of); Movahedi, B., E-mail: b.movahedi@ast.ui.ac.ir [Department of Nanotechnology Engineering, Faculty of Advanced Sciences and Technologies, University of Isfahan, Isfahan, 81746-73441 (Iran, Islamic Republic of); Milani, M. [Faculty of Advanced Materials and Renewable Energy Research Center, Tehran (Iran, Islamic Republic of)

2016-11-01

Alumina/yttria nanocomposite powder as an yttrium aluminum garnet (YAG) precursor was synthesized via partial wet route using urea and ammonium hydrogen carbonate (AHC) as precipitants, respectively. The products were characterized using X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy and energy dispersive spectroscopy. The use of urea produced very tiny spherical Y-compounds with chemical composition of Y{sub 2}(CO{sub 3}){sub 3}·nH{sub 2}O, which were attracted to the surface of alumina nanoparticles and consequently, a core-shell structure was obtained. The use of ammonium hydrogen carbonate produced sheets of Y-compounds with chemical composition of Y(OH)CO{sub 3} covering the alumina nanoparticles. A fine-grained YAG ceramic (about 500 nm), presenting a non-negligible transparency (45% RIT at IR range) was obtained by the spark plasma sintering (SPS) of alumina-yttria nanocomposite synthesized in the urea system. This amount of transmission was obtained by only the sintering of the powder specimen without any colloidal forming process before sintering or adding any sintering aids or dopant elements. However, by spark plasma sintering of alumina-yttria nanocomposite powder synthesized in AHC system, an opaque YAG ceramic with an average grain size of 1.2 μm was obtained. - Highlights: • Urea proved to be an appropriate precipitant for obtaining a core-shell alumina/yttria nanocomposite. • Alumina/yttria nanocomposite powders with more appropriate morphology and highly sinterability. • A fine-grained YAG ceramic was obtained by SPS of alumina-yttria nanocomposite.

Dehydration and crystallization kinetics of zirconia-yttria gels

International Nuclear Information System (INIS)

Ramanathan, S.; Muraleedharan, R.V.; Roy, S.K.; Nayar, P.K.K.

1995-01-01

Zirconia and zirconia-yttria gels containing 4 and 8 mol% yttria were obtained by coprecipitation and drying at 373 K. The dehydration and crystallization behavior of the dried gels was studied by DSC, TG, and XRD. The gels undergo elimination of water over a wide temperature range of 373--673 K. The peak temperature of the endotherm corresponding to dehydration and the kinetic constants for the process were not influenced by the yttria content of the gel. The enthalpy of dehydration observed was in good agreement with the heat of vaporization data. The dehydration was followed by a sharp exothermic crystallization process. The peak temperature of the exotherm and the activation energy of the process increased with an increase in yttria content, while the enthalpy of crystallization showed a decrease. The ''glow effect'' reduced with increasing yttria content. Pure zirconia crystallizes in the tetragonal form while the zirconia containing 4 and 8 mol% yttria appears to crystallize in the cubic form

Composite Sr- and V-doped LaCrO3/YSZ sensor electrode operating at low oxygen levels

DEFF Research Database (Denmark)

Lund, Anders; Jacobsen, Torben; Hansen, Karin Vels

2012-01-01

A porous composite electrode of La0.8Sr0.2Cr0.97V0.03O3 -delta (LSCV) and yttria-stabilised zirconia (YSZ) was evaluated as a possible candidate for high-temperature potentiometric oxygen sensor measuring electrodes. The oxygen processes at the electrode were characterised by performing electroch....... The relatively low response time at 700º C at an oxygen partial pressure of around 5x10-6 bar and an inlet gas flow rate of 8 L h-1 makes the LSCV/YSZ electrode suitable for use as an potentiometric oxygen sensor electrodes.......A porous composite electrode of La0.8Sr0.2Cr0.97V0.03O3 -delta (LSCV) and yttria-stabilised zirconia (YSZ) was evaluated as a possible candidate for high-temperature potentiometric oxygen sensor measuring electrodes. The oxygen processes at the electrode were characterised by performing...... and 400 nm. At oxygen partial pressures around 0.2 bar at 700º C, the oxygen reaction is dominated by solid-state diffusion of oxide ions and surface reaction kinetics. At oxygen partial pressures around 10-5 bar above 800º C, gas phase mass transport processes dominate the impedance spectra...

Tungsten metallizing alumina--yttria ceramics

International Nuclear Information System (INIS)

Cowan, R.E.; Stoddard, S.D.

1977-03-01

The ease with which high-alumina bodies may be metallized with tungsten is improved by additions of yttria to the alumina. Mechanisms of this bonding process were studied by use of optical and electron microscopy, electron microprobe, and tensile tests. Variables studied included yttria content of the body and the firing temperature during metallizing. The study showed that a reaction between the tungsten and the yttrogarnet grain boundary phase markedly improved adherence

Effects of CO2 laser irradiation on the wettability and human skin fibroblast cell response of magnesia partially stabilised zirconia

International Nuclear Information System (INIS)

Hao, L.; Lawrence, J.

2003-01-01

Human skin fibroblast cells in vitro responses on the surface of a bioinert zirconia ceramic partially stabilised with magnesia partially stabilised zirconia (MgO-PSZ) bioinert ceramic before and after CO 2 laser treatment were investigated to find the interrelationship between the cell adhesion, wettability and laser parameters. Contact angle, θ, measurements of a set of test liquids were a clear indication that surface treatment of the MgO-PSZ with a CO 2 laser brought about a reduction in θ, indicating that the wettability of the MgO-PSZ had been enhanced. A relationship was found between the wettability and the microstructure of the MgO-PSZ surface and laser processing parameters. It was subsequently deduced that the factors active in causing the observed modification in the wettability of the MgO-PSZ were the increases in the surface O 2 content and the polar component of the surface energy, γ sv p , the latter resulting from surface melting and resolidification. Moreover, the investigation into the human skin fibroblast cell response revealed that the CO 2 laser treatment of the MgO-PSZ had resulted in a surface favourable for cell adhesion, as the extent of cell attachment and adhesion on the MgO-PSZ surface was enhanced depending on laser parameters. Such an improvement in cell adhesion, which could be greatly beneficial to developing enhanced bonding at the tissue and implant interface, was influenced by the surface properties of the modified MgO-PSZ, particular wettability

Microencapsulation of silicon nitride particles with yttria and yttria-alumina precursors

International Nuclear Information System (INIS)

Garg, A.K.; De Jonghe, L.C.

1990-01-01

Procedures are described to deposit uniform layers of yttria and yttria-alumina precursors on fine powders and whiskers of silicon nitride. The coatings were produced by aging at elevated temperatures aqueous systems containing the silicon nitride core particles, yttrium and aluminum nitrates, and urea. Optimum concentrations of the core particles, in relation to the reactants, were established to promote surface deposition of the oxide precursors. Polymeric dispersants were used effectively to prevent agglomeration of the solids during the microencapsulation process. The morphology of the powders was characterized using scanning and transmission electron microscopy. The mechanisms for the formation of the coated layers are discussed. A description is provided that allows qualitative assessment of the experimental factors that determine microencapsulation by a slurry method

High yttria ferritic ODS steels through powder forging

Energy Technology Data Exchange (ETDEWEB)

Kumar, Deepak [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Prakash, Ujjwal, E-mail: ujwalfmt@iitr.ac.in [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Dabhade, Vikram V. [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Laha, K.; Sakthivel, T. [Mechanical Metallurgy Group, IGCAR, Kalpakkam, Tamilnadu 603102 (India)

2017-05-15

Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y{sub 2}O{sub 3} (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility. - Highlights: •ODS steels with yttria contents beyond the conventional limit of 0.5 wt% were fabricated by powder forging in a hydrogen atmosphere. •All the alloys exhibited significant ductility. •This may be attributed to improved inter-particle bonding due to reduction of surface oxides by hydrogen. •Strength in excess of 300 MPa was obtained at 973 K for 0.5%, 1% and 1.5% yttria ODS alloys. •Powder forging is a promising route to fabricate ODS steels and permits development of compositions with up to 1.5% yttria.

Effects of CO{sub 2} laser irradiation on the wettability and human skin fibroblast cell response of magnesia partially stabilised zirconia

Energy Technology Data Exchange (ETDEWEB)

Hao, L.; Lawrence, J

2003-10-15

Human skin fibroblast cells in vitro responses on the surface of a bioinert zirconia ceramic partially stabilised with magnesia partially stabilised zirconia (MgO-PSZ) bioinert ceramic before and after CO{sub 2} laser treatment were investigated to find the interrelationship between the cell adhesion, wettability and laser parameters. Contact angle, {theta}, measurements of a set of test liquids were a clear indication that surface treatment of the MgO-PSZ with a CO{sub 2} laser brought about a reduction in {theta}, indicating that the wettability of the MgO-PSZ had been enhanced. A relationship was found between the wettability and the microstructure of the MgO-PSZ surface and laser processing parameters. It was subsequently deduced that the factors active in causing the observed modification in the wettability of the MgO-PSZ were the increases in the surface O{sub 2} content and the polar component of the surface energy, {gamma}{sub sv}{sup p}, the latter resulting from surface melting and resolidification. Moreover, the investigation into the human skin fibroblast cell response revealed that the CO{sub 2} laser treatment of the MgO-PSZ had resulted in a surface favourable for cell adhesion, as the extent of cell attachment and adhesion on the MgO-PSZ surface was enhanced depending on laser parameters. Such an improvement in cell adhesion, which could be greatly beneficial to developing enhanced bonding at the tissue and implant interface, was influenced by the surface properties of the modified MgO-PSZ, particular wettability.

Low climate stabilisation under diverse growth and convergence scenarios

International Nuclear Information System (INIS)

Markandya, A.; González-Eguino, M.; Criqui, P.; Mima, S.

2014-01-01

In the last decade a number of papers have analysed the consequences of achieving the greenhouse gas concentration levels necessary to maintain global temperature increases below 2 °C above preindustrial levels. Most models and scenarios assume that future trends in global GDP will be similar to the growth experienced in the past century, which would imply multiplying current output by about 19 times in the 21st century. However, natural resource and environmental constraints suggest that future global economic growth may not be so high. Furthermore, the environmental implications of such growth depend on how it is distributed across countries. This paper studies the implications on GHG abatement policies of low global GDP growth and high convergence levels in GDP per capita across countries. A partial equilibrium model (POLES) of the world's energy system is used to provide detailed projections up to 2050 for the different regions of the world. The results suggest that while low stabilisation could be technically feasible and economically viable for the world in all the scenarios considered, it is more likely to occur with more modest global growth. However, that will imply higher global abatement costs relative to GDP. Convergence in living standards on the other hand places greater pressures in terms of the required reduction in emissions. In general we find that there are major differences between regions in terms of the size and the timing of abatement costs and economic impact. - Highlights: • We study the implications of GDP growth and convergence on climate stabilisation. • A partial equilibrium model (POLES) of the world's energy system is used. • Low climate stabilisation is technically feasible and economically viable. • Low stabilisation is more likely to occur with more modest global growth. • Convergence places pressure in terms of the required reduction in emissions

High yttria ferritic ODS steels through powder forging

Science.gov (United States)

Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

2017-05-01

Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y2O3 (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility.

Oxygen diffusion in nanocrystalline yttria-stabilized zirconia: the effect of grain boundaries.

Science.gov (United States)

De Souza, Roger A; Pietrowski, Martha J; Anselmi-Tamburini, Umberto; Kim, Sangtae; Munir, Zuhair A; Martin, Manfred

2008-04-21

The transport of oxygen in dense samples of yttria-stabilized zirconia (YSZ), of average grain size d approximately 50 nm, has been studied by means of 18O/16O exchange annealing and secondary ion mass spectrometry (SIMS). Oxygen diffusion coefficients (D*) and oxygen surface exchange coefficients (k*) were measured for temperatures 673partial pressure of 900 mbar. No evidence is found for fast diffusion along grain boundaries. Rather, the analysis indicates that grain boundaries hinder oxygen transport.

Transport properties of water and oxygen in yttria-stabilized zirconia; Transporteigenschaften von Wasser und Sauerstoff in Yttrium-stabilisiertem Zirkoniumdioxid

Energy Technology Data Exchange (ETDEWEB)

Pietrowski, Martha Joanna

2012-12-21

Oxide materials that adopt the fluorite structure, such as yttria-stabilized zirconia (YSZ), play a central role in electrochemical devices, such as fuel cells and sensors, because of their high ionic conductivity. By virtue of the technological importance of such devices there exists a broad interest in understanding and enhancing mass transport processes in YSZ. In such oxides, not only does transport through the bulk play a critical role; interfaces (internal and external) have an influence, too. The effect of interfaces on the transport properties, however, is not investigated in detail, and remains in many places unclear. In this work two open questions concerning the effect of interfaces on mass transport processes in YSZ are addressed: The first issue is the phenomenon of protonic conductivity observed at low temperatures for nanocrystalline YSZ in wet atmospheres. This protonic conductivity was attributed to the high density of interfaces (grain boundaries) caused by the nanostructure, in which protonic species can be mobile. Through isotope exchange experiments with subsequent Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) the presence of hydrogen in nano-YSZ was confirmed. Questions as to which hydrogen-containing species are present and which transport path is taken in nanocrystalline YSZ were examined by means of in-situ of near-infrared (NIR) spectroscopy. The results indicate that water is adsorbed on internal surfaces, such as pores and micro-cracks. Microscopic analysis of nanocrystalline YSZ showed first indications of nanopores. The second issue concerned transport across the solidgas interface, that is the surface. To this end, oxygen isotope exchange experiments were performed on single crystal samples of yttria-stabilised zirconia under wet and dry conditions as function of oxygen partial pressure pO{sub 2} and water partial pressure pH{sub 2}O with subsequent determination of the oxygen isotope profiles by ToF-SIMS. As expected, the

High temperature measurements of the microwave dielectric properties of ceramics

International Nuclear Information System (INIS)

Baeraky, T.A.

1999-06-01

Equipment has been developed for the measurement of dielectric properties at high temperature from 25 to 1700 deg. C in the microwave frequency range 614.97 to 3620.66 MHz using the cavity perturbation technique, to measure the permittivity of a range of ceramic materials. The complex permittivities of the standard materials, water and methanol, were measured at low temperature and compared with the other published data. A statistical analysis was made for the permittivity measurements of water and methanol using sample holders of different diameter. Also the measurements of these materials were used to compare the simple perturbation equation with its modifications and alternation correction methods for sample shape and the holes at the two endplates of the cavity. The dielectric properties of solid materials were investigated from the permittivity measurements on powder materials, shown in table 4.7, using the dielectric mixture equations. Two kinds of ceramics, oxide and nitrides, were selected for the high temperature dielectric measurements in microwave frequency ranges. Pure zirconia, yttria-stabilised zirconia, and Magnesia-stabilised zirconia are the oxide ceramics while aluminium nitride and silicon nitride are the nitride ceramics. A phase transformation from monoclinic to tetragonal was observed in pure zirconia in terms of the complex permittivity measurements, and the conduction mechanism in three regions of temperature was suggested to be ionic in the first region and a mixture of ionic and electronic in the second. The phase transition disappeared with yttria-stabilised zirconia but it was observed with magnesia-stabilised zirconia. Yttria doped zirconia was fully stabilised while magnesia stabilised was partially stabilised zirconia. The dielectric property measurements of aluminium nitride indicated that there is a transition from AIN to AlON, which suggested that the external layer of the AIN which was exposed to the air, contains alumina. It was

The Physical Behavior of Stabilised Soft Clay by Electrokinetic Stabilisation Technology

Science.gov (United States)

Azhar, A. T. S.; Nordin, N. S.; Azmi, M. A. M.; Embong, Z.; Sunar, N.; Hazreek, Z. A. M.; Aziman, M.

2018-04-01

Electrokinetic Stabilisation (EKS) technology is the combination processes of electroosmosis and chemical grouting. This technique is most effective in silty and clayey soils where the hydraulic conductivity is very low. Stabilising agents will assist the EKS treatment by inducing it into soil under direct current. The movement of stabilising agents into soil is governed by the principle of electrokinetics. The aim of this study is to evaluate the physical behavior of soft soil using the EKS technology as an effective method to strengthen soft clay soils with calcium chloride (CaCl2) as the stabilising agent. Stainless steel plates were used as the electrodes, while 1.0 mol/l of CaCl2 was used as the electrolyte that fed at the anode compartment. Soft marine clay at Universiti Tun Hussein Onn Malaysia was used as the soil sample. The EKS treatment was developed at Research Centre for Soft Soil (RECESS), UTHM with a constant voltage gradient (50 V/m) in 21 days. The result shows that the shear strength of treated soil was increased across the soil sample. The treated soil near the cathode showed the highest value of shear strength (24.5 – 33 kPa) compared with the anode and in the middle of the soil sample.

Lattice parameters and electrical resistivity of Ceria-Yttria solid solutions

International Nuclear Information System (INIS)

Rey, Jose Fernando Queiruga

2002-01-01

Ce0 2 :u mol% Y 2 O 3 (u=0, 4, 6, 8, 10 and 12) solid solutions were prepared by the conventional powder mixture technique. The main purposes of this work are: the study of the dependence of the lattice parameter of the Ceria cubic phase on the Yttria content, comparing the experimental data with data calculated according to the existing theoretical models; to determine the dependence of the ionic conductivity on the Yttria content; and to study the stability of the cubic fluorite phase after extensive thermal treatments (aging) of the Ceria-Yttria specimens. The results show that the lattice parameter of the solid solutions follows the Vegard's law and can be described by the two reported theoretical models. The 8 mol% Yttria-doped Ceria was found to present the largest value of ionic conductivity. Preliminary results show that a large decrease is found for only 1 h aging at 700 deg C and that the ionic conductivity decreases for ceramic specimens aged for times up to 10 h. (author)

High-temperature deformation of a mechanically alloyed niobium-yttria alloy

International Nuclear Information System (INIS)

Chou, I.; Koss, D.A.; Howell, P.R.; Ramani, A.S.

1997-01-01

Mechanical alloying (MA) and hot isostatic pressing have been used to process two Nb alloys containing yttria particles, Nb-2 vol.%Y 2 O 3 and Nb-10 vol.%Y 2 O 3 . Similar to some thermomechanically processed nickel-based alloys, both alloys exhibit partially recrystallized microstructures, consisting of a 'necklace' of small recrystallized grains surrounding much larger but isolated, unrecrystallized, cold-worked grains. Hot compression tests from 1049 to 1347 C (0.5-0.6T MP ) of the 10% Y 2 O 3 alloy show that MA material possesses a much higher yield and creep strength than its powder-blended, fully recrystallized counterpart. In fact, the density-compensated specific yield strength of the MA Nb-10Y 2 O 3 exceeds that of currently available commercial Nb alloys. (orig.)

Characterization of plasma sprayed NiCrAlY-Yttria stabilized zirconia coatings

International Nuclear Information System (INIS)

Bhave, V.S.; Rakhasia, R.H.; Tripathy, P.K.; Hubli, R.C.; Sengupta, P.; Bhanumurthy; Satpute, R.U.; Sreekumar, K.P.; Thiyagarajan, T.K.; Padmanabhan, P.V.A.

2004-01-01

Plasma sprayed coatings of yttria stabilized zirconia are used in many advanced technologies for thermal and chemical barrier applications. Development and characterization of NiCrAlY-yttria stabilized zirconia duplex coatings on Inconel substrates is reported in this paper. Plasma spraying was carried out using the 40 kW atmospheric plasma spray facility at the Laser and Plasma Technology Division, BARC. A bond coat of NiCrAlY was deposited on Inconel substrates and yttria stabilized zirconia (YSZ) was deposited over the bond coat. The coatings have been characterized by x-ray diffraction and EPMA. It is observed that the coating characteristics are affected by the input power to the torch. (author)

Properties Of Soda/Yttria/Silica Glasses

Science.gov (United States)

Angel, Paul W.; Hann, Raiford E.

1994-01-01

Experimental study of glass-formation compositional region of soda/ yttria/silicate system and of selected physical properties of glasses within compositional region part of continuing effort to identify glasses with high coefficients of thermal expansion and high softening temperatures, for use as coatings on superalloys and as glass-to-metal seals.

Yttria-doped zirconia as solid electrolyte for fuel-cell applications

Energy Technology Data Exchange (ETDEWEB)

Butz, Benjamin

2009-11-27

7.3-10 mol% yttria-doped zirconia (YDZ) was studied with emphasis on its long-term stability as solid electrolyte. The decomposition of common 8.5YDZ (950 C) was detected by analytical TEM. As second issue, the microstructural and chemical properties of nanocrystalline 7.3YDZ thin films were investigated. Metastable t''-YDZ was found to precipitate in nanoscaled regions in YDZ up to 10 mol% yttria. Furthermore, a revised boundary of the c+t phase field, in which YDZ decomposes, is presented. (orig.)

Yttria-doped zirconia as solid electrolyte for fuel-cell applications

Energy Technology Data Exchange (ETDEWEB)

Butz, Benjamin

2009-11-27

7.3-10 mol% yttria-doped zirconia (YDZ) was studied with emphasis on its long-term stability as solid electrolyte. The decomposition of common 8.5YDZ (950 C) was detected by analytical TEM. As second issue, the microstructural and chemical properties of nanocrystalline 7.3YDZ thin films were investigated. Metastable t''-YDZ was found to precipitate in nanoscaled regions in YDZ up to 10 mol% yttria. Furthermore, a revised boundary of the c+t phase field, in which YDZ decomposes, is presented. (orig.)

Algal stabilisation of estuarine sediments

International Nuclear Information System (INIS)

1992-01-01

The presence of benthic microalgae can increase the stability of intertidal sediments and influence sediment fluxes within an estuarine environment. Therefore the relative importance of algal stabilisation needs to be understood to help predict the effects of a tidal barrage. The biogenic stabilisation of intertidal estuarine sediments by epipelic diatom films and the macrophyte Vaucheria was studied at three sites on the Severn Estuary. The cohesive strength meter (CSM) was developed to measure surface critical shear stress with varied algal density. A number of techniques have been used to determine the general in situ erodibility of cohesive estuarine sediments. The measurements of sediment shear strength and critical erosion velocity were investigated. Field experiments were undertaken to investigate the effect of algae on binding sediments, and a predictive method for the assessment of sediment stabilisation by algal binding was developed. (author)

Plasmachemical synthesis of nanopowders of yttria and zirconia from dispersed water-salt-organic mixtures

Science.gov (United States)

Novoselov, Ivan; Karengin, Alexander; Shamanin, Igor; Alyukov, Evgeny; Gusev, Alexander

2018-03-01

Article represents results on theoretical and experimental research of yttria and zirconia plasmachemical synthesis in air plasma from water-salt-organic mixtures "yttrium nitrate-water-acetone" and "zirconyl nitrate-water-acetone". On the basis of thermotechnical calculations the influence of organic component on lower heat value and adiabatic combustion temperature of water-salt-organic mixtures as well as compositions of mixtures providing their energy-efficient plasma treatment were determined. The calculations found the influence of mass fraction and temperature of air plasma supporting gas on the composition of plasma treatment products. It was determined the conditions providing yttria and zirconia plasmachemical synthesis in air plasma. During experiments it was b eing carried out the plasmachemical synthesis of yttria and zirconia powders in air plasma flow from water -salt-organic mixtures. Analysis of the results for obtained powders (scanning electron microscopy, X-ray diffraction analysis, BET analysis) confirm nanostructure of yttria and zirconia.

Room temperature synthesis of high temperature stable lanthanum phosphate–yttria nano composite

International Nuclear Information System (INIS)

Sankar, Sasidharan; Raj, Athira N.; Jyothi, C.K.; Warrier, K.G.K.; Padmanabhan, P.V.A.

2012-01-01

Graphical abstract: A facile aqueous sol–gel route involving precipitation–peptization mechanism followed by electrostatic stabilization is used for synthesizing nanocrystalline composite containing lanthanum phosphate and yttria. Highlights: ► A novel lanthanum phosphate–Y 2 O 3 nano composite is synthesized for the first time using a modified facile sol gel process. ► The composite becomes crystalline at 600 °C and X-ray diffraction pattern is indexed for monoclinic LaPO 4 and cubic yttria. ► The composite synthesized was tested up to 1300 °C and no reaction between the phases of the constituents is observed with the morphologies of the phases being retained. -- Abstract: A facile aqueous sol–gel route involving precipitation–peptization mechanism followed by electrostatic stabilization is used for synthesizing nanocrystalline composite containing lanthanum phosphate and yttria. Lanthanum phosphate (80 wt%)–yttria (20 wt%) nano composite (LaPO 4 –20%Y 2 O 3 ), has an average particle size of ∼70 nm after heat treatment of precursor at 600 °C. TG–DTA analysis reveals that stable phase of the composite is formed on heating the precursor at 600 °C. The TEM images of the composite show rod shape morphology of LaPO 4 in which yttria is acquiring near spherical shape. Phase identification of the composite as well as the phase stability up to 1300 °C was carried out using X-ray diffraction technique. With the phases being stable at higher temperatures, the composite synthesized should be a potential material for high temperature applications like thermal barrier coatings and metal melting applications.

Algal stabilisation of estuarine sediments

International Nuclear Information System (INIS)

1992-01-01

The presence of benthic microalgae can increase the stability of intertidal sediments and influence sediment fluxes within an estuarine environment. Therefore the relative importance of algal stabilisation needs to be understood to help predict the effects of a tidal barrage. The objectives of this study are: to assess the significance of stabilisation of sediments by algae, in relation to the changes in hydrodynamic and sedimentological regimes arising from the construction of tidal power barrages; to identify a reliable and meaningful method of measuring the effectiveness, including duration, of algal binding on sediment stability, and to relate this method to other methods of measuring critical erosion velocity and sediment shear strength; to undertake a series of field experiments investigating the effect of algae on binding sediments and the parameters which could potentially influence such binding and to develop a predictive method for the assessment of sediment stabilisation by algal binding. This report contains plates, figures and tables. (author)

Silicone elastomers with covalently incorporated aromatic voltage stabilisers

DEFF Research Database (Denmark)

A Razak, Aliff Hisyam; Skov, Anne Ladegaard

2017-01-01

to the incorporationof an aromatic voltage stabiliser, were prepared by cross-linking synthesised polydimethylsiloxane–polyphenylmethylsiloxane (PDMS–PPMS) copolymers. PPMS possesses voltage stabilisation capabilitiesbut is immiscible in PDMS, and thus the copolymerisation of the two components was necessary...... forhomogeneity. Concentrations of the voltage stabiliser were varied by changing the molecular weights ofthe PPMS in the copolymer. The developed elastomers were inherently soft with enhanced electricalbreakdown strengths, due to delocalisedp-electrons of the aromatic constituent. An optimumconcentration...

Mixed conductivity, structural and microstructural characterization of titania-doped yttria tetragonal zirconia polycrystalline/titania-doped yttria stabilized zirconia composite anode matrices

International Nuclear Information System (INIS)

Colomer, M.T.; Maczka, M.

2011-01-01

Taking advantage of the fact that TiO 2 additions to 8YSZ cause not only the formation of a titania-doped YSZ solid solution but also a titania-doped YTZP solid solution, composite materials based on both solutions were prepared by solid state reaction. In particular, additions of 15 mol% of TiO 2 give rise to composite materials constituted by 0.51 mol fraction titania-doped yttria tetragonal zirconia polycrystalline and 0.49 mol fraction titania-doped yttria stabilized zirconia (0.51TiYTZP/0.49TiYSZ). Furthermore, Y 2 (Ti 1-y Zr y ) 2 O 7 pyrochlore is present as an impurity phase with y close to 1, according to FT-Raman results. Lower and higher additions of titania than that of 15 mol%, i.e., x=0, 5, 10, 20, 25 and 30 mol% were considered to study the evolution of 8YSZ phase as a function of the TiO 2 content. Furthermore, zirconium titanate phase (ZrTiO 4 ) is detected when the titania content is equal or higher than 20 mol% and this phase admits Y 2 O 3 in solid solution according to FE-SEM-EDX. The 0.51TiYTZP/0.49TiYSZ duplex material was selected in this study to establish the mechanism of its electronic conduction under low oxygen partial pressures. In the pO 2 range from 0.21 to 10 -7.5 atm. the conductivity is predominantly ionic and constant over the range and its value is 0.01 S/cm. The ionic plus electronic conductivity is 0.02 S/cm at 1000 o C and 10 -12.3 atm. Furthermore, the onset of electronic conductivity under reducing conditions exhibits a -1/4 pO 2 dependence. Therefore, it is concluded that the n-type electronic conduction in the duplex material can be due to a small polaron-hopping between Ti 3+ and Ti 4+ . -- Graphical abstract: FE-SEM micrograph of a polished and thermal etched surface of a Ti-doped YTZP/Ti-doped YSZ composite material. Display Omitted Research highlights: → Ti-doped YTZP/Ti-doped YSZ composite materials are mixed conductors under low partial pressures. → From 5 mol% of TiO 2 , Y 2 (Ti 1-y ,Zr y ) 2 O 7 pyrochlore is

Oxygen partial pressure sensor for gases

International Nuclear Information System (INIS)

Barbero, J.A.; Azcona, M.A.; Orce, A.

1997-01-01

Precise measurement of very low oxygen partial pressure is important in both laboratories and industries. Particularly in nuclear industry, it is relevant in the different steps of the nuclear fuel fabrication. It is presented an instrument which is handy and of easy construction, suitable for the measurement of oxygen partial pressure of gases, in the range of 10 -6 -1 atm. It is based on a solid electrolyte galvanic cell, using Yttria doped zirconia as a ceramic membrane. Through an indirect measurement and calibration, the instrument can be used to measure the content of free oxygen in liquids. It is a import feature in NPP instrumentation. The equipment was calibrated with mixtures of special nonreactive gases. (author). 5 refs

Successfully combining SUGRA hybrid inflation and moduli stabilisation

International Nuclear Information System (INIS)

Davis, S.C.

2008-01-01

Inflation and moduli stabilisation mechanisms work well independently, and many string-motivated supergravitymodels have been proposed for them. However a complete theory will contain both, and there will be (gravitational) interactions between the two sectors. These give corrections to the inflaton potential, which generically ruin inflation. This holds true even for fine-tuned moduli stabilisation schemes. We show that a viable combined model can be obtained if it is the Kaehler functions (G=K+ln vertical stroke W vertical stroke 2 ) of the two sectors that are added, rather than the superpotentials (as is usually done). Interaction between the two sectors does still impose some restrictions on the moduli stabilisation mechanism, which are derived. Significantly, we find that the (post-inflation) moduli stabilisation scale no longer needs to be above the inflationary energy scale. (orig.)

Fabrication of Yttria stabilized zirconia thin films on poroussubstrates for fuel cell applications

Energy Technology Data Exchange (ETDEWEB)

Leming, Andres [Univ. of California, Berkeley, CA (United States)

2003-06-16

A process for the deposition of yttria stabilized zirconia (YSZ) films, on porous substrates, has been developed. These films have possible applications as electrolyte membranes in fuel cells. The films were deposited from colloidal suspensions through the vacuum infiltration technique. Films were deposited on both fully sintered and partially sintered substrates. A critical cracking thickness for the films was identified and strategies are presented to overcome this barrier. Green film density was also examined, and a method for improving green density by changing suspension pH and surfactant was developed. A dependence of film density on film thickness was observed, and materials interactions are suggested as a possible cause. Non-shorted YSZ films were obtained on co-fired substrates, and a cathode supported solid oxide fuel cell was constructed and characterized.

Successfully combining SUGRA hybrid inflation and moduli stabilisation

Energy Technology Data Exchange (ETDEWEB)

Davis, S.C. [CEA Centre d' Etudes de Saclay, 91 - Gif-sur-Yvette (France). Service de Physique Theorique; Postma, M. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)]|[Nationaal Inst. voor Kernfysica en Hoge-Energiefysica (NIKHEF), Amsterdam (Netherlands)

2008-01-15

Inflation and moduli stabilisation mechanisms work well independently, and many string-motivated supergravitymodels have been proposed for them. However a complete theory will contain both, and there will be (gravitational) interactions between the two sectors. These give corrections to the inflaton potential, which generically ruin inflation. This holds true even for fine-tuned moduli stabilisation schemes. We show that a viable combined model can be obtained if it is the Kaehler functions (G=K+ln vertical stroke W vertical stroke {sup 2}) of the two sectors that are added, rather than the superpotentials (as is usually done). Interaction between the two sectors does still impose some restrictions on the moduli stabilisation mechanism, which are derived. Significantly, we find that the (post-inflation) moduli stabilisation scale no longer needs to be above the inflationary energy scale. (orig.)

Quadratic stabilisability of multi-agent systems under switching topologies

Science.gov (United States)

Guan, Yongqiang; Ji, Zhijian; Zhang, Lin; Wang, Long

2014-12-01

This paper addresses the stabilisability of multi-agent systems (MASs) under switching topologies. Necessary and/or sufficient conditions are presented in terms of graph topology. These conditions explicitly reveal how the intrinsic dynamics of the agents, the communication topology and the external control input affect stabilisability jointly. With the appropriate selection of some agents to which the external inputs are applied and the suitable design of neighbour-interaction rules via a switching topology, an MAS is proved to be stabilisable even if so is not for each of uncertain subsystem. In addition, a method is proposed to constructively design a switching rule for MASs with norm-bounded time-varying uncertainties. The switching rules designed via this method do not rely on uncertainties, and the switched MAS is quadratically stabilisable via decentralised external self-feedback for all uncertainties. With respect to applications of the stabilisability results, the formation control and the cooperative tracking control are addressed. Numerical simulations are presented to demonstrate the effectiveness of the proposed results.

Oxygen partial pressure sensor for gases

Energy Technology Data Exchange (ETDEWEB)

Barbero, J.A.; Azcona, M.A.; Orce, A. [Comision Nacional de Energia Atomica, San Carlos de Bariloche (Argentina). Centro Atomico Bariloche

1997-10-01

Precise measurement of very low oxygen partial pressure is important in both laboratories and industries. Particularly in nuclear industry, it is relevant in the different steps of the nuclear fuel fabrication. It is presented an instrument which is handy and of easy construction, suitable for the measurement of oxygen partial pressure of gases, in the range of 10{sup -6}-1 atm. It is based on a solid electrolyte galvanic cell, using Yttria doped zirconia as a ceramic membrane. Through an indirect measurement and calibration, the instrument can be used to measure the content of free oxygen in liquids. It is a import feature in NPP instrumentation. The equipment was calibrated with mixtures of special nonreactive gases. (author). 5 refs.

Long-time aging in 3 mol.% yttria-stabilized tetragonal zirconia polycrystals at human body temperature.

Science.gov (United States)

Keuper, Melanie; Berthold, Christoph; Nickel, Klaus Georg

2014-02-01

We present new findings on the low-temperature degradation of yttria-stabilized zirconia at 37°C over several years and at high and low partial pressures of water. With the aid of focused ion beam cross-section confirmation studies we are able to show an extensive linear, continuous degradation without retardation, even at low temperatures and low water pressures. The characteristic layer growth and its inferred rate constant imply a lifetime of tens of years under simple tension and open the possibility of studying the longevity of these ceramics more rigorously. In addition, we show reproducibility complications of accelerated aging tests by the use of different autoclaves and possible implications for standardized procedures. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Melting point of yttria

International Nuclear Information System (INIS)

Skaggs, S.R.

1977-06-01

Fourteen samples of 99.999 percent Y 2 O 3 were melted near the focus of a 250-W CO 2 laser. The average value of the observed melting point along the solid-liquid interface was 2462 +- 19 0 C. Several of these same samples were then melted in ultrahigh-purity oxygen, nitrogen, helium, or argon and in water vapor. No change in the observed temperature was detected, with the exception of a 20 0 C increase in temperature from air to helium gas. Post test examination of the sample characteristics, clarity, sphericity, and density is presented, along with composition. It is suggested that yttria is superior to alumina as a secondary melting-point standard

Transparent Yttria for IR Windows and Domes - Past and Present

National Research Council Canada - National Science Library

Hogan, Patrick; Stefanik, Todd; Willingham, Charles; Gentilman, Richard

2004-01-01

... (sapphire, ALON, spinel), its thermal shock performance is similar. In fact, 7 out of 7 flat yttria windows were successfully wind-tunnel tested under hypersonic conditions simulating representative surface-to-air interceptor missile flights...

Study of the creep of lime-stabilised zirconia

International Nuclear Information System (INIS)

Saint-Jacques, Robert G.

1971-09-01

This research thesis reports the study of creep of stabilised zirconia containing between 13 and 20 per cent of lime, at temperatures between 1.200 and 1.400 C, and under compression stresses between 500 and 4.000 pounds by square inch. Specimens are polycrystalline with an average grain diameter between 7 and 29 microns. The author notably shows that the creep rate of lime-stabilised zirconia is directly proportional to the applied stress, and that the creep apparent activation energy is close to activation energy of volume self-diffusion of calcium and zirconium in lime-stabilised zirconia. Results of creep tests show that, in the studied conditions, the creep rate is directly proportional to the inverse of the grain average diameter, and this is in compliance with the Gifkins and Snowden theory of creep by sliding at grain boundaries. The author also shows that the creep rate of the lime stabilised zirconia varies with lime content, and reaches a maximum when zirconia contains about 15 per cent of lime. Lower creep rates obtained for higher and lower lime contents are explained [fr

Transparent Yttria for IR Windows and Domes - Past and Present

National Research Council Canada - National Science Library

Hogan, Patrick; Stefanik, Todd; Willingham, Charles; Gentilman, Richard

2004-01-01

...) atmospheric transmission band at both ambient and elevated temperatures. Current state-of-the-art yttria's thermomechanical properties are adequate for a number of IR window and dome applications, but only marginal for the most demanding missions...

Phase stability in yttria-stabilized zirconia from first principles

Energy Technology Data Exchange (ETDEWEB)

Carbogno, Christian; Scheffler, Matthias [Materials Department, University of California, Santa Barbara, CA (United States); Fritz-Haber-Institut der Max-Planck-Gesellschaft, Berlin (Germany); Levi, Carlos G.; Van de Walle, Chris G. [Materials Department, University of California, Santa Barbara, CA (United States)

2012-07-01

Zirconia based ceramics are of pivotal importance for a variety of industrial technologies, e.g., for thermal barrier coatings in gas and airplane turbines. Naturally, the stability of such coatings at elevated temperatures plays a critical role in these applications. It is well known that an aliovalent doping of tetragonal ZrO{sub 2} with yttria, which induces oxygen vacancies due to charge conservation, increases its thermodynamic stability. However, the atomistic mechanisms that determine the phase stability of such yttria-stabilized Zirconia (YSZ) coatings are not yet fully understood. In this work, we use density functional theory calculations to assess the electronic structure of the different YSZ polymorphs at various levels of doping. With the help of population analysis schemes, we are able to unravel the intrinsic mechanisms that govern the interaction in YSZ and that can so explain the relative stabilities of the various polymorphs. We critically compare our results to experimental measurements and discuss the implications of our findings with respect to other oxides.

Characterization of cubic yttria-stabilized zirconia obtained by spray pyrolysis

International Nuclear Information System (INIS)

Halmenschlager, Cibele M.; Nunes, Marilia; Vieira, Ramaugusto; Bergmann, Carlos Perez; Falcade, Tiago; Malfatti, Celia de Fraga

2009-01-01

Yttria-stabilized-zirconia (YSZ) has been the object of many studies as a SOFC electrolyte. The aim of this work is to produce, by spray pyrolysis process, thin and dense films of YSZ. A disk of steel 316L, previously heated, was used as substrate. The film was obtained with zirconium acetylacetonate (Zr(C 6 H 7 O 2 ) 4 ) and yttrium chloride (YCl 3.6 H 2 O), dissolved in a mixture of ethanol + butyl carbitol with volume ratio (1:1). ZrO 2 amorphous films were deposited in the substrate heated at many temperatures. After thermal treatment at 700 deg C the films were changed into cubic yttria-stabilized-zirconia structure. The thin films obtained were characterized by thermal analysis, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and micro-Raman spectroscopy. (author)

Very low pressure plasma sprayed yttria-stabilized zirconia coating using a low-energy plasma gun

International Nuclear Information System (INIS)

Zhu, Lin; Zhang, Nannan; Bolot, Rodolphe; Planche, Marie-Pierre; Liao, Hanlin; Coddet, Christian

2011-01-01

In the present study, a more economical low-energy plasma source was used to perform a very low pressure plasma-spray (VLPPS) process. The plasma-jet properties were analyzed by means of optical emission spectroscopy (OES). Moreover, yttria-stabilized zirconia coating (YSZ) was elaborated by a F100 low-power plasma gun under working pressure of 1 mbar, and the substrate specimens were partially shadowed by a baffle-plate during plasma spraying for obtaining different coating microstructures. Based on the SEM observation, a column-like grain coating was deposited by pure vapor deposition at the shadowed region, whereas, in the unshadowed region, the coating exhibited a binary microstructure which was formed by a mixed deposition of melted particles and evaporated particles. The mechanical properties of the coating were also well under investigation. (orig.)

Production of defect-poor nanostructured ceramics of yttria-zirconia

NARCIS (Netherlands)

Sagel-Ransijn, C.D.; Sagel-Ransijn, C.D.; Winnubst, Aloysius J.A.; Kerkwijk, B.; Burggraaf, Anthonie; Burggraaf, A.J.; Verweij, H.

1997-01-01

For the production of nanostructured ceramics of yttria-zirconia four powders differing in agglomerate strength, agglomerate size and crystallite size are compared. An ultra-fine-grained ceramic with a final density of 98% and a grain size of 0.18 μm could be produced from a hydrothermally

Stabilisation of microalgae: Iodine mobilisation under aerobic and anaerobic conditions.

Science.gov (United States)

Han, Wei; Clarke, William; Pratt, Steven

2015-10-01

Mobilisation of iodine during microalgae stabilisation was investigated, with the view of assessing the potential of stabilised microalgae as an iodine-rich fertiliser. An iodine-rich waste microalgae (0.35 ± 0.05 mg I g(-1) VS(added)) was stabilised under aerobic and anaerobic conditions. Iodine mobilisation was linearly correlated with carbon emission, indicating iodine was in the form of organoiodine. Comparison between iodine and nitrogen mobilisation relative to carbon emission indicated that these elements were, at least in part, housed separately within the cells. After stabilisation, there were 0.22 ± 0.05 and 0.19 ± 0.01 mg g(-1) VS(added) iodine remaining in the solid in the aerobic and anaerobic processed material respectively, meaning 38 ± 5.0% (aerobic) and 50 ± 8.6% (anaerobic) of the iodine were mobilised, and consequently lost from the material. The iodine content of the stabilised material is comparable to the iodine content of some seaweed fertilisers, and potentially satisfies an efficient I-fertilisation dose. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance assessment of stabilised/solidified waste-forms

OpenAIRE

Antemir, Aurora

2010-01-01

A method to treat contaminated land is stabilisation/solidification (S/S), which physically encapsulates and chemically stabilises the contaminants. The current knowledge on the behaviour of S/S systems is based upon scarce and incomplete data, mostly obtained from laboratory simulations or small scale trials of the technology. The field performance of S/S soils is largely unknown.\\ud \\ud The aim of this research was to improve the understanding of the long-term performance of S/S soils, by e...

Modelling and experiments on NTM stabilisation at ASDEX upgrade

Energy Technology Data Exchange (ETDEWEB)

Urso, Laura

2009-07-27

In the next fusion device ITER the so-called neoclassical tearing modes (NTMs) are foreseen as being extremely detrimental to plasma confinement. This type of resistive instability is related to the presence in the plasma of magnetic islands. These are experimentally controlled with local electron cyclotron current drive (ECCD) and the island width decay during NTM stabilisation is modelled using the so-called Modified Rutherford equation. In this thesis, a modelling of the Modified Rutherford equation is carried out and simulations of the island width decay are compared with the experimentally observed ones in order to fit the two free machine-independent parameters present in the equation. A systematic study on a database of NTM stabilisation discharges from ASDEX Upgrade and JT-60U is done within the context of a multi-machine benchmark for extrapolating the ECCD power requirements for ITER. The experimental measurements in both devices are discussed by means of consistency checks and sensitivity analysis and used to evaluate the two fitting parameters present in the Modified Rutherford equation. The influence of the asymmetry of the magnetic island on stabilisation is for the first time included in the model and the effect of ECCD on the marginal island after which the mode naturally decays is quantified. The effect of radial misalignment and over-stabilisation during the experiment are found to be the key quantities affecting the NTM stabilisation. As a main result of this thesis, the extrapolation to ITER of the NTM stabilisation results from ASDEX Upgrade and JT-60U shows that 10MW of ECCD power are enough to stabilise large NTMs as long as the O-point of the island and the ECCD beam are perfectly aligned. In fact, the high ratio between the island size at saturation and the deposition width of the ECCD beam foreseen for ITER is found to imply a maximum allowable radial misalignment of 2-3 cm and little difference in terms of gained performance between

Modelling and experiments on NTM stabilisation at ASDEX upgrade

International Nuclear Information System (INIS)

Urso, Laura

2009-01-01

In the next fusion device ITER the so-called neoclassical tearing modes (NTMs) are foreseen as being extremely detrimental to plasma confinement. This type of resistive instability is related to the presence in the plasma of magnetic islands. These are experimentally controlled with local electron cyclotron current drive (ECCD) and the island width decay during NTM stabilisation is modelled using the so-called Modified Rutherford equation. In this thesis, a modelling of the Modified Rutherford equation is carried out and simulations of the island width decay are compared with the experimentally observed ones in order to fit the two free machine-independent parameters present in the equation. A systematic study on a database of NTM stabilisation discharges from ASDEX Upgrade and JT-60U is done within the context of a multi-machine benchmark for extrapolating the ECCD power requirements for ITER. The experimental measurements in both devices are discussed by means of consistency checks and sensitivity analysis and used to evaluate the two fitting parameters present in the Modified Rutherford equation. The influence of the asymmetry of the magnetic island on stabilisation is for the first time included in the model and the effect of ECCD on the marginal island after which the mode naturally decays is quantified. The effect of radial misalignment and over-stabilisation during the experiment are found to be the key quantities affecting the NTM stabilisation. As a main result of this thesis, the extrapolation to ITER of the NTM stabilisation results from ASDEX Upgrade and JT-60U shows that 10MW of ECCD power are enough to stabilise large NTMs as long as the O-point of the island and the ECCD beam are perfectly aligned. In fact, the high ratio between the island size at saturation and the deposition width of the ECCD beam foreseen for ITER is found to imply a maximum allowable radial misalignment of 2-3 cm and little difference in terms of gained performance between

Purification in the interaction between yttria mould and Nb-silicide-based alloy during directional solidification: A novel effect of yttrium

International Nuclear Information System (INIS)

Ma, Limin; Tang, Xiaoxia; Wang, Bin; Jia, Lina; Yuan, Sainan; Zhang, Hu

2012-01-01

Nb-silicide-based alloys were directionally solidified in yttria moulds. As a result of thermal dissociation of yttria, the alloys were slightly contaminated with oxygen, which caused a competitive oxidation between yttrium and hafnium. The addition of 0.15 at.% yttrium reduced the oxygen increment by 42%, because the buoyant inclusions concentrated around the top surface. The yttrium addition caused a significant purification of the interaction between the yttria mould and the Nb-silicide-based alloys during the directional solidification.

Thickness effects of yttria-doped ceria interlayers on solid oxide fuel cells

Science.gov (United States)

Fan, Zeng; An, Jihwan; Iancu, Andrei; Prinz, Fritz B.

2012-11-01

Determining the optimal thickness range of the interlayed yttria-doped ceria (YDC) films promises to further enhance the performance of solid oxide fuel cells (SOFCs) at low operating temperatures. The YDC interlayers are fabricated by the atomic layer deposition (ALD) method with one super cycle of the YDC deposition consisting of 6 ceria deposition cycles and one yttria deposition cycle. YDC films of various numbers of ALD super cycles, ranging from 2 to 35, are interlayered into bulk fuel cells with a 200 um thick yttria-stabilized zirconia (YSZ) electrolyte. Measurements and analysis of the linear sweep voltammetry of these fuel cells reveal that the performance of the given cells is maximized at 10 super cycles. Auger elemental mapping and X-ray photoelectron spectroscopy (XPS) techniques are employed to determine the film completeness, and they verify 10 super cycles of YDC to be the critical thickness point. This optimal YDC interlayer condition (6Ce1Y × 10 super cycles) is applied to the case of micro fuel cells as well, and the average performance enhancement factor is 1.4 at operating temperatures of 400 and 450 °C. A power density of 1.04 W cm-2 at 500 °C is also achieved with the optimal YDC recipe.

Waste Stabilisation Ponds

OpenAIRE

Von Sperling, Marcos

2007-01-01

"Waste Stabilisation Ponds is the third volume in the series Biological Wastewater Treatment. The major variants of pond systems are fully covered, namely: facultative ponds anaerobic ponds aerated lagoons maturation ponds The book presents in a clear and informative way the main concepts, working principles, expected removal efficiencies, design criteria, design examples, construction aspects, operational guidelines and sludge managment for pond systems. About the series: The series is...

Thermo-stimulated luminescence of ion-irradiated yttria-stabilized zirconia

Energy Technology Data Exchange (ETDEWEB)

Costantini, Jean-Marc [CEA, DMN, SRMA, 91191 Gif-sur Yvette Cedex (France); Beuneu, Francois [LSI, CEA-CNRS-Ecole Polytechnique, 91128 Palaiseau Cedex (France); Fasoli, Mauro; Galli, Anna; Vedda, Anna; Martini, Marco, E-mail: jean-marc.costantini@cea.fr [CNR-IFN (Italy)

2011-03-23

Yttria-stabilized zirconia (ZrO{sub 2}:Y{sup 3+}) single crystals (with 9.5 mol% Y{sub 2}O{sub 3}) were irradiated with ions (from 1 MeV He to 2.6 GeV U). Electron paramagnetic resonance (EPR) data show that two kinds of colour centres (F{sup +}-type and T centres) are produced. Thermo-stimulated luminescence (TSL) data exhibit a quite strong peak at {approx} 500-550 K in the glow curves of all irradiated samples regardless of the ion species and energy. Moreover, the 3D-TSL measurements reveal that this peak is correlated with a light emission at a wavelength of {approx} 620 nm (i.e. photon energy {approx} 2 eV). The TSL peak maximum temperatures are consistent with characteristic temperatures of about 500 K of annealing stages of colour centres. However, the trap-depth energies (ranging between 0.7 and 1.4 eV) deduced from the initial rise of partially cleaned TSL peaks, or from a rough approximation using Urbach's formula, are rather larger than the activation energies for defect recovery, ranging between 0.3 and 0.7 eV, as deduced from the EPR data. The processes involved in TSL are discussed in relation to available photoluminescence and defect energy-level data.

Stabilisation effects of superparamagnetic nanoparticles on clustering in nanocomposite microparticles and on magnetic behaviour

Energy Technology Data Exchange (ETDEWEB)

Mandel, K., E-mail: karl-sebastian.mandel@isc.fraunhofer.de [Fraunhofer Institute for Silicate Research, ISC, Neunerplatz 2, 97082 Würzburg (Germany); University Würzburg, Chair of Chemical Technology of Materials Synthesis, Röntgenring 11, 97070 Würzburg (Germany); Hutter, F., E-mail: frank.hutter@isc.fraunhofer.de [Fraunhofer Institute for Silicate Research, ISC, Neunerplatz 2, 97082 Würzburg (Germany); Gellermann, C., E-mail: carsten.gellermann@isc.fraunhofer.de [Fraunhofer Institute for Silicate Research, ISC, Neunerplatz 2, 97082 Würzburg (Germany); Sextl, G., E-mail: gerhard.sextl@isc.fraunhofer.de [Fraunhofer Institute for Silicate Research, ISC, Neunerplatz 2, 97082 Würzburg (Germany); University Würzburg, Chair of Chemical Technology of Materials Synthesis, Röntgenring 11, 97070 Würzburg (Germany)

2013-04-15

Superparamagnetic nanoparticles of magnetite were coprecipitated from iron salts, dispersed with nitric acid and stabilised either by lactic acid (LA) or by a polycarboxylate-ether polymer (MELPERS4343, MP). The differently stabilised nanoparticles were incorporated into a silica matrix to form nanocomposite microparticles. The silica matrix was prepared either from tetraethylorthosilicate (TEOS) or from an aqueous sodium silicate (water glass) solution. Stabilisation of nanoparticles had a crucial influence on microparticle texture and nanoparticle distribution in the silica matrix. Magnetic measurements in combination with transmission electron microscopy (TEM) investigations suggest a uniform magnetic interaction of nanoparticles in case of LA stabilisation and magnetically interacting nanoparticle clusters of different sizes in case of MP stabilisation. Splitting of blocking temperature (T{sub B}) and irreversible temperature (T{sub ir}) in zero field cooled (ZFC) and field cooled (FC) measurements is discussed in terms of nanoparticle clustering. -- Highlights: ► Superparamagnetic nanoparticles were synthesised, dispersed and stabilised. ► Stabilisation is either via a polycarboxylate ether polymer or lactic acid. ► Stabilised nanoparticles were incorporated into silica to form composite particles. ► Depending on the stabilisation, nanoparticle clustering in the composites differed. ► Clustering influences zero field cooled/field cooled magnetic measurements.

Effect of yttria addition on the stability of porous chromium oxide ceramics in supercritical water

International Nuclear Information System (INIS)

Dong Ziqiang; Chen Weixing; Zheng Wenyue; Guzonas, Dave

2013-01-01

Porous chromium oxide (Cr 2 O 3 ) ceramics were prepared by oxidizing highly porous chromium carbides that were obtained by a reactive sintering method, and were evaluated at temperatures ranging from 375 °C to 625 °C in supercritical water (SCW) environments with a fixed pressure of 25–30 MPa. Reactive element yttrium was introduced to the porous oxide ceramic by adding various amounts of yttria of 5, 10 and 20 wt.%, respectively, prior to reactive sintering. The exposure in SCW shows that the porous chromium oxide is quite stable in SCW at 375 °C. However, the stability decreased with increasing temperature. It is well known that chromium oxide can be oxidized to soluble chromium (VI) species in SCW when oxygen is present. Adding yttria increases the stability of chromium oxide in SCW environments. However, adding yttria higher than 5 wt.% increased the weight loss of porous chromium oxide samples because of the direct dissociation of Y 2 O 3 in SCW.

Mechanical characterization of the 3Y-TZP co-doped with yttria and niobia Equimolar addition

International Nuclear Information System (INIS)

Assis, Joao Marcos Kruszynski de; Nono, Maria do Carmo de Andrade; Dorat, Daniele Ramos; Fonseca, Flavia Baccaro; Reis, Danieli Aparecida

2010-01-01

The main goal of this work is to study the effect of the yttria and niobia equimolar addition in the 3Y-TZP on the mechanical properties (hardness, fracture toughness and four point bending strength) aiming to get a stable tetragonal phase (t´) under applied stress, to use as TBC´s. Four compositions with equimolar addition of yttria and niobia in the 3Y-TZP were produced, 13%, 14.5%, 16% and 17.5%. The mixtures were prepared in high energy ball milling for 10 minutes and the samples prepared on uniaxial and isostatic pressing. The selected temperature sintering was 1.550 deg C for 1 hour. Analyses of X-Ray Diffraction, hardness, fracture toughness and four point bending strength were performed. An increase on the mechanical properties analyzed was expected with yttria and niobia addition in comparison to 3Y-TZP, but instead a decrease was observed after these additions. (author)

Fly ash stabilisation of gravel roads; Flygaska som foerstaerkningslager i grusvaeg

Energy Technology Data Exchange (ETDEWEB)

Macsik, Josef

2006-01-15

Majority of the existing gravel roads have low bearing capacity during spring and autumn, due to thaw and/or rain. Low bearing capacity leads often to bad road conditions. This situation results in higher costs for the lumber industry and the public. Management of gravel roads all the year around would traditionally require excavation of frost susceptible soils and replacement with natural materials. Fly ash (from bio fuels) has good technical properties as bearing layer in road constructions. Fly ash stabilised gravel roads have better function and longer life span with less maintenance than traditional gravel roads. The aim of this project is to show how fly ash stabilisation of gravel roads can increase bearing capacity and what its environmental impact is. The overall aim is to make it easier for entrepreneurs and consulting companies to use fly ash during gravel road renovation and/or constructing new gravel roads. This report targets fly ash producers and road constructors as well as environmental agencies. Two different pilot tests were investigated in this study, Norberg with fly ash from Stora Enso Fors AB, and Boerje (Uppsala) with fly ash from Vattenfall Uppsala AB. Both road sections with related reference section were investigated during a two year period. Only fly ash was used in the bearing layer at Norberg and fly ash gravel was used at Boerje. Bearing capacity was investigated twice, for both locations, November 2003 one month after the road renovation and during thawing, April 2004. Water samples from lysimeters, ground water and surface water were only collected and analysed from Norberg. Experience from the fly ash stabilised road sections show that curing and traffic load can with time compensate for less compaction. The same is noticed at Boerje, although deflection measurements show that there are small differences. Stabilisation of gravel roads increases the roads bearing capacity. Two years after stabilisation 90 timber loads were

States of fragility: stabilisation and its implications for humanitarian action.

Science.gov (United States)

Collinson, Sarah; Elhawary, Samir; Muggah, Robert

2010-10-01

This paper explores the evolution of international stabilisation agendas and their significance for humanitarian action. Stabilisation includes a combination of military, humanitarian, political and economic activities to control, contain and manage areas affected by armed conflict and complex emergencies. Encompassing narrow security objectives and broader peace-building efforts, stabilisation is both a conservative and potentially transformative, comprehensive and long-term agenda. The open-ended approach allows for widely varying interpretations and applications in different circumstances and by different actors with an assortment of implications for humanitarian action. The relationship between the two is highly uncertain and contentious, due not only to the controversies surrounding stabilisation policies, but also to deep-seated ambiguities at the heart of humanitarianism. While humanitarian actors are preoccupied with the growing involvement of the military in the humanitarian sphere, the paper argues that it is trends in the humanitarian-political interface that represent the more fundamental dilemma. © 2010 The Author(s). Journal compilation © Overseas Development Institute, 2010.

Limitations of potentiometric oxygen sensors operating at low oxygen levels

DEFF Research Database (Denmark)

Lund, Anders; Jacobsen, Torben; Hansen, Karin Vels

2011-01-01

The electrochemical processes that limit the range of oxygen partial pressures in which potentiometric oxygen sensors can be used, were analysed using a theoretical and an experimental approach. Electrochemical impedance spectroscopy was performed on porous Pt/yttria stabilised zirconia (YSZ......) electrodes between 10−6 and 0.2 bar and at temperatures between 500 and 950 °C. The flow of oxide ions and electron holes through a sensor cell, with a YSZ electrolyte, were calculated under similar conditions. The oxygen permeation of the sensor cell was insignificant at an oxygen partial pressure of 10......−6 bar for an inlet flow rate higher than 2 L h−1 between 600 and 800 °C. The polarisation resistance measured between 10−6 and 10−4 bar was found to be inversely proportional to the oxygen partial pressure, nearly temperature independent and inversely proportional to the inlet gas flow rate, which shows...

Stability and stabilisation of a class of networked dynamic systems

Science.gov (United States)

Liu, H. B.; Wang, D. Q.

2018-04-01

We investigate the stability and stabilisation of a linear time invariant networked heterogeneous system with arbitrarily connected subsystems. A new linear matrix inequality based sufficient and necessary condition for the stability is derived, based on which the stabilisation is provided. The obtained conditions efficiently utilise the block-diagonal characteristic of system parameter matrices and the sparseness of subsystem connection matrix. Moreover, a sufficient condition only dependent on each individual subsystem is also presented for the stabilisation of the networked systems with a large scale. Numerical simulations show that these conditions are computationally valid in the analysis and synthesis of a large-scale networked system.

Preparation of stabilized zirconia (Zr O2) with Yttria (Y2 O3) by simultaneous precipitation

International Nuclear Information System (INIS)

Campos, M. de.

1993-01-01

The preparation of cubic or tetragonal partially stabilized zirconia with Yttria by simultaneous precipitation was studied. The metals Zr and Y, in nitric acid and hydrogen peroxide medium, were precipitated with ammonia solution. The variables studied were: the pH of the aqueous medium (8, 9 e 10) and yttrium molar concentration (2, 3 and 5 mol %) in the final product. The resulting oxide samples were divided and calcined at 500, 700 and 900 0 C, separately. After that, all samples were sintered at 1500 0 C for one hour. For physico-chemical characterization were used techniques such as: ICP-AES, XRF, XRD, SEM etc. The results have showed that using this approach predominant cubic and/or tetragonal phases can be reached with theoretical density over 92% and grain size lower than 1 μm. (author)

CLIC Drive Beam Phase Stabilisation

CERN Document Server

Gerbershagen, Alexander; Schulte, Daniel

The thesis presents phase stability studies for the Compact Linear Collider (CLIC) and focuses in particular on CLIC Drive Beam longitudinal phase stabilisation. This topic constitutes one of the main feasibility challenges for CLIC construction and is an essential component of the current CLIC stabilisation campaign. The studies are divided into two large interrelated sections: the simulation studies for the CLIC Drive Beam stability, and measurements, data analysis and simulations of the CLIC Test Facility (CTF3) Drive Beam phase errors. A dedicated software tool has been developed for a step-by-step analysis of the error propagation through the CLIC Drive Beam. It uses realistic RF potential and beam loading amplitude functions for the Drive and Main Beam accelerating structures, complete models of the recombination scheme and compressor chicane as well as of further CLIC Drive Beam modules. The tool has been tested extensively and its functionality has been verified. The phase error propagation at CLIC h...

Gravel road stabilisation of Ehnsjoevaegen, Hallstavik[Using fly ash]; Skogsbilvaegsrenovering av Ehnsjoevaegen, Hallstavik

Energy Technology Data Exchange (ETDEWEB)

Macsik, Josef; Svedberg, Bo [Ecoloop, Stockholm (Sweden)

2006-03-15

Fly ash in geotechnical applications has stabilising, isolating, low permeability and hardening effect. Fly ash can be used in road constructions with low bearing capacity, as well as on top cover material on landfills. The aim of the project was to build a road section with fly ash stabilised gravel, based on laboratory studies, and follow up technical and environmental aspect during the first year after stabilisation. The overall aim of this project was to evaluate fly ash from Holmen Paper, Hallstavik, from technical and environmental point of view in a gravel road construction. A gravel road, Ehnsjoevaegen, was stabilised with fly ash during autumn 2004. This road was a low priority road. The fly ash stabilised road section was 1300 m long. Gravel from the road Ehnsjoevaegen was stabilised and investigated in a laboratory study. Leachability of metals and geotechnical aspects were investigated. The laboratory study showed that fly ash stabilised gravel has high shear strength, however its thawing resistance is not fully acceptable. Additives of cement or merit are needed in order to increase its thawing resistance. The actual road section is not going to be used during thawing period and no additives were used. The test road is divided into different sections including a reference section. The road stabilisation work was conducted with gravel transported to Ehnsjoevaegen from off site and not with gravel from the site. Fly ash was tipped off on a levelled road, followed by tipping of gravel. Mixing fly ash and gravel was done on site by a road scraper. After the mixing the road was gravelled with 0,1 m graded gravel. In this project the fly ash had low water content. In order to get optimal compaction water was added from a tanker supplying water before compacted with a compactor. Results from the pilot test shows that fly ash stabilised gravel can be tipped, mixed and compacted effectively. Tipping can be optimised if fly ash and gravel is mixed in a mixer

Thermal barrier coating by electron beam-physical vapor deposition of zirconia co-doped with yttria and niobia

Directory of Open Access Journals (Sweden)

Daniel Soares de Almeida

2010-08-01

Full Text Available The most usual ceramic material for coating turbine blades is yttria doped zirconia. Addition of niobia, as a co-dopant in the Y2O3-ZrO2 system, can reduce the thermal conductivity and improve mechanical properties of the coating. The purpose of this work was to evaluate the influence of the addition of niobia on the microstructure and thermal properties of the ceramic coatings. SEM on coatings fractured cross-section shows a columnar structure and the results of XRD show only zirconia tetragonal phase in the ceramic coating for the chemical composition range studied. As the difference NbO2,5-YO1,5 mol percent increases, the tetragonality increases. A significant reduction of the thermal conductivity, measured by laser flash technique in the zirconia coating co-doped with yttria and niobia when compared with zirconia-yttria coating was observed.

Investigations into the stabilisation of drugs by sugar glasses : I. Tablets prepared from stabilised alkaline phosphatase

NARCIS (Netherlands)

Eriksson, H.J.C.; Hinrichs, W.L.J.; van Veen, B.; Somsen, G.W.; de Jong, G.J.; Frijlink, H.W.

2002-01-01

The aim of this study was to investigate the formulation of sugar glass stabilised alkaline phosphatase from bovine intestine (BIAP) into tablets. Two major subjects of tablet formulation were investigated. First, the compaction behaviour of the inulin sugar glass was investigated. Secondly, the

Preparing Stabilisation for 21st Century Security Challenges

Directory of Open Access Journals (Sweden)

Steven A. Zyck

2015-11-01

Full Text Available Stabilisation, as a concept and set of practices, has proliferated over the past two decades and is now implicitly integrated into a range of global frameworks. However, this enthusiasm has at times risked turning this increasingly common, albeit contested, idea into a piece of jargon that discounts its unique facets: a focus on all sorts of violence, not just conflict, that create political instability and human harm and a problem-solving approach that draws selectively on various forms of intervention (e.g., statebuilding, counterinsurgency, peacekeeping, etc. without being beholden to any one toolkit. The pragmatism inherent within the concept of stabilisation will grow increasingly important as new security challenges emerge or proliferate. These include the fragmentation and regionalisation of conflict systems, transnational organised crime, large-scale migration and new, disruptive technologies. Novel approaches rooted in big data and technology will increasingly need to be applied. Most importantly, in foreign policy, military and development communities often driven by perceptions about what causes, ends or prevents violence, stabilisation must maintain its agnostic, problem-solving roots and allegiance to evidence over ideology.

The effectiveness of arthroscopic stabilisation for failed open shoulder instability surgery.

Science.gov (United States)

Millar, N L; Murrell, G A C

2008-06-01

We identified ten patients who underwent arthroscopic revision of anterior shoulder stabilisation between 1999 and 2005. Their results were compared with 15 patients, matched for age and gender, who had a primary arthroscopic stabilisation during the same period. At a mean follow-up of 37 and 36 months, respectively, the scores for pain and shoulder function improved significantly between the pre-operative and follow-up visits in both groups (p = 0.002), with no significant difference between them (p = 0.4). The UCLA and Rowe shoulder scores improved significantly (p = 0.004 and p = 0.002, respectively), with no statistically significant differences between groups (p = 0.6). Kaplan-Meier analysis for time to recurrent instability showed no differences between the groups (p = 0.2). These results suggest that arthroscopic revision anterior shoulder stabilisation is as reliable as primary arthroscopic stabilisation for patients who have had previous open surgery for recurrent anterior instability.

The production of hydrotalcite from magnesite ore as non-toxic heat stabiliser for polyvinyl chloride

Directory of Open Access Journals (Sweden)

J. van der Laan

2005-09-01

Full Text Available In recent years polyvinyl chloride (PVC processors had to submit to worldwide pressure to convert to environmentally friendly stabilisers such as hydrotalcite (HT, since most of the heat stabilisers currently in use contain heavy metals such as lead, cadmium or barium – these being highly toxic. The presently used HT production process is, however, very expensive as it involves the recovering of magnesium from seawater magnesia. The purpose of this study was to prove that it is indeed possible to produce cost effective and non-toxic HT from an alternative source. During this study the costing and heat stabilising ability of the hydrotalcite produced from magnesite was compared to that of commercially available heat stabilisers. The effect of the pre-mixing process, as well as the influence of particle size distribution was also investigated. A cost comparative and stabilising efficiency study indicated the cost effectiveness of HT produced from magnesite ore, in comparison with other commercially available stabilisers. The use of HT as produced from magnesite ore would indeed assist in the worldwide changeover to environmentally friendly stabilisers.

The effect of the presence of fine YSZ particles on the performance of porous nickel electrodes

NARCIS (Netherlands)

de Boer, B.; de Boer, B.; Gonzalez, M.; Gonzalez Cuenca, M.M.; Bouwmeester, Henricus J.M.; Verweij, H.

2000-01-01

The electrochemical performance of a porous nickel electrode with its surface modified by deposition with fine yttria-stabilised zirconia (YSZ) powder is compared with that of the ‘bare’ electrode. Image analysis of the electrode microstructure yields values for the triple phase boundary (TPB)

Ceramic Composites of 3Y-TZP Doped with CuO: Processing, Microstructure and Tribology

NARCIS (Netherlands)

Ran, S.

2006-01-01

The work described in this thesis is about processing, microstructure and tribology of CuO doped 3Y-TZP (3 mol% yttria stabilised tetragonal zirconia polycrystals) composite ceramics. This group of materials has shown attractive properties such as superplastic behaviour at elevated temperature and a

stabilisation of niger delta fat clay with blend of binders for subgrade

African Journals Online (AJOL)

HOD

Construction of roads on fine-grained soils without any form of stabilisation is a major ... and Portland Cement (PC) to improve its plasticity, California Bearing Ratio (CBR), and swell. .... sand, DCA, lateralite, and cement in stabilising a fat clay.

Fly ashes as binders for the stabilisation of gravel. Laboratory tests and preparations for a field test; Flygaskor som bindemedel foer stabilisering av grusmaterial. Laboratorieundersoekningar samt foerberedelser infoer provbyggandet

Energy Technology Data Exchange (ETDEWEB)

Lahtinen, Pentti; Jyraevae, Harri; Maijala, Aino; Macsik, Josef

2005-04-01

The project is based on the results of a significant research project FACE (Fly Ash in Civil Engineering). The project aims at the development of binder recipes based on a chosen fly ash from Holmen Paper's Hallsta Pappersbruk for the renovation of a road. The development will benefit from the Finnish research and experience on this type of binders for geotechnical applications. The stabilisation should result in improving bearing capacity and better long-term durability and service life of the gravel roads. The environmentally friendly stabilisation system comprises also the possibility to reuse and recycle the material that already exists in the road to be renovated. The test materials for the development project were the gravel from a chosen test road and the fly ash of Holmen Paper AB. The fly ash was used as the binder material. The geotechnical tests included characterisation tests of the test materials, tests on the stabilised mixes and control tests for the stabilisation recipe. Also, there were tests for the assessment of the environmental impact of the stabilisation. Side by side with those tests there has been a full-scale test, a separate project in Hallstavik, to test the stabilisation process with respect to the technical, environmental and economical aspects of construction. The full-scale test will be reported separately. The project results imply that fly ash can be beneficially used as a binder for the stabilisation of gravel materials and similar materials. Fly ash can be used also with small amounts of other binder materials like cement or blast-furnace slag in order to have a frost resistant material. The project gives also basis for the development of binders for other types of applications, both for the renovation purposes and for the improvement of spoils for construction purposes.

Study on the influences of reduction temperature on nickel-yttria-stabilized zirconia solid oxide fuel cell anode using nickel oxide-film electrode

Science.gov (United States)

Jiao, Zhenjun; Ueno, Ai; Suzuki, Yuji; Shikazono, Naoki

2016-10-01

In this study, the reduction processes of nickel oxide at different temperatures were investigated using nickel-film anode to study the influences of reduction temperature on the initial performances and stability of nickel-yttria-stabilized zirconia anode. Compared to conventional nickel-yttria-stabilized zirconia composite cermet anode, nickel-film anode has the advantage of direct observation at nickel-yttria-stabilized zirconia interface. The microstructural changes were characterized by scanning electron microscopy. The reduction process of nickel oxide is considered to be determined by the competition between the mechanisms of volume reduction in nickel oxide-nickel reaction and nickel sintering. Electrochemical impedance spectroscopy was applied to analyze the time variation of the nickel-film anode electrochemical characteristics. The anode performances and microstructural changes before and after 100 hours discharging and open circuit operations were analyzed. The degradation of nickel-film anode is considered to be determined by the co-effect between the nickel sintering and the change of nickel-yttria-stabilized zirconia interface bonding condition.

The stabilisation of final focus system

Indian Academy of Sciences (India)

The StaFF (stabilisation of final focus) system will use interferometers to monitor the relative ... quadrupole magnets will be the most demanding application, where mutual and beam- ... interferometers to measure lines of a geodetic network to record relative motion between two beam ... coupled interferometer design.

Yttria and ceria doped zirconia thin films grown by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Saporiti, F.; Juarez, R. E., E-mail: cididi@fi.uba.ar [Grupo de Materiales Avanzados, Facultad de Ingenieria, Universidad de Buenos Aires (Argentina); Audebert, F. [Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina); Boudard, M. [Laboratoire des Materiaux et du Genie Physique (CNRS), Grenoble (France)

2013-11-01

The Yttria stabilized Zirconia (YSZ) is a standard electrolyte for solid oxide fuel cells (SOFCs), which are potential candidates for next generation portable and mobile power sources. YSZ electrolyte thin films having a cubic single phase allow reducing the SOFC operating temperature without diminishing the electrochemical power density. Films of 8 mol% Yttria stabilized Zirconia (8YSZ) and films with addition of 4 weight% Ceria (8YSZ + 4CeO{sub 2}) were grown by pulsed laser deposition (PLD) technique using 8YSZ and 8YSZ + 4CeO{sub 2} targets and a Nd-YAG laser (355 nm). Films have been deposited on Soda-Calcia-Silica glass and Si(100) substrates at room temperature. The morphology and structural characteristics of the samples have been studied by means of X-ray diffraction and scanning electron microscopy. Films of a cubic-YSZ single phase with thickness in the range of 1-3 Micro-Sign m were grown on different substrates (author)

Labelling and evaluation of new stabilised neurotensin (8-13) analogues for SPET

International Nuclear Information System (INIS)

Chavatte, K.; Terriere, D.; Jeannin, L.

1998-01-01

Neurotensin (8-13) analogues were biologically stabilised by replacement of the peptide bond between amino acids 8 and 9 by the reduced ψ(CH 2 -NH) isostere. DTPA analogues for In-111 labelling and 2-bromo-phenyl-acetyl analogues for radioiodination, showed receptor affinities in the low nanomolar range in combination with a biological half live in human plasma up to 275 minutes. Biodistribution studies in male Wistar rats of metabolically stabilised and non-stabilised 111 In-DTPA-NT(8-13) analogues showed a major clearance from the blood through the kidneys. 125 I-labelled Neurotensin (8-13) analogues showed accumulation up to 2.2% of the injected dose per g tissue in the liver which might be an important disadvantage when diagnosis of tumours in the gut is aimed. It is strongly suggested that stabilised neurotensin (8-13) analogues whether labelled with In-111, I-123 and the near future with Tc-99m, may act as new potential peptidergic radiopharmaceuticals for SPET diagnosis of different NT-receptor positive tumours like non-endocrine pancreas carcinoma, small cell lung carcinoma or colon adeno carcinoma. It is enticing to speculate that metabolically stabilised Neurotensin (8-13) analogues labelled with an appropriate isotope might be useful in therapy of different human cancers. (author)

Characterization of amorphous yttria layers deposited by aqueous solutions of Y-chelate alkoxides complex

Energy Technology Data Exchange (ETDEWEB)

Kim, Young-Soon, E-mail: kyscjb@i-sunam.com; Lee, Yu-Ri; Kim, Byeong-Joo; Lee, Jae-Hun; Moon, Seung-Hyun; Lee, Hunju

2015-01-15

Highlights: • Economical method for crack-free amorphous yttria layer deposition by dip coating. • Simpler process for planar yttria film as a diffusion barrier and nucleation layer. • Easy control over the film properties with better characteristics. • Easy control over the thickness of the deposited films. • A feasible process that can be easily adopted by HTSCC industries. - Abstract: Crack-free amorphous yttria layers were deposited by dip coating in solutions of different Y-chelate alkoxides complex. Three Y-chelate solutions of different concentrations were prepared using yttrium acetate tetrahydrate, yttrium stearic acid as Y source materials. PEG, diethanolamine were used as chelating agents, while ethanol, methanol and tetradecane were used as solvent. Three different combinations of chelating and solvents were used to prepare solutions for Y{sub 2}O{sub 3} dip coating on SUS, electropolished and non-electropolished Hastelloy C-276 substrates. The thickness of the films was varied by changing the number of dipping cycles. At an optimized condition, the substrate surface roughness (rms) value was reduced from ∼50 nm to ∼1 nm over a 10 × 10 μm{sup 2} area. After Y{sub 2}O{sub 3} deposition, MgO was deposited using ion-beam assisted deposition (IBAD), then LaMnO{sub 3} (LMO) was deposited using sputtering and GdBCO was deposited using reactive co-evaporation by deposition and reaction (RCE-DR). Detailed X-ray study indicates that LMO/MgO/Y{sub 2}O{sub 3} and GdBCO/LMO/MgO/Y{sub 2}O{sub 3} stack films have good out-of-plane and in-plane textures with strong c-axis alignment. The critical current (Ic) of GdBCO/LMO/MgO/Y{sub 2}O{sub 3} multilayer structure varied from 190 to 420 A/cm with different solutions, when measured at 77 K. These results demonstrated that amorphous yttria can be easily deposited by dip coating using Y-chelates complex as a diffusion barrier and nucleation layer.

On the design and role of passive stabilisation within the ST40 spherical tokamak

Science.gov (United States)

Buxton, P. F.; Asunta, O.; Gryaznevich, M. P.; Lockley, D.; McNamara, S.; Medvedev, S.; Ruiz de Villa Valdés, E.; Whitfield, G.; Wood, J. M.

2018-06-01

The position of passive stabilisation has been optimised for the low aspect ratio tokamak ST40. We find that passive stabilisation is most effective when conductors are placed near the plasma’s x-point, and the combined effect of having both inboard and outboard passive stabilisation significantly reduces the vertical instability growth rate. The growth rate can be further decreased by cooling the passive conductors down to 80 K. Two concepts for passive stabilisation are considered, passive plates and passive coils, and the relative advantages and disadvantages of each are discussed. Both concepts involve connecting the upper and lower conductors in an ‘anti-symmetric’ manner, which prevents large currents from being induced.

Hysteresis in the solid oxide fuel cell cathode reaction

DEFF Research Database (Denmark)

Jacobsen, Torben; Zachau-Christiansen, Birgit; Bay, Lasse

2001-01-01

The oxygen electrode reaction at the Pt/yttria-stabilised zirconia (YSZ) interface is investigated at 1000degreesC on Pt point electrodes on YSZ and YSZ point contacts on Pt. Linear potential sweeps show a pronounced non-linear current-voltage relation and inductive hysteresis, in particular at l...

Global D-brane models with stabilised moduli and light axions

Science.gov (United States)

Cicoli, Michele

2014-03-01

We review recent attempts to try to combine global issues of string compactifications, like moduli stabilisation, with local issues, like semi-realistic D-brane constructions. We list the main problems encountered, and outline a possible solution which allows globally consistent embeddings of chiral models. We also argue that this stabilisation mechanism leads to an axiverse. We finally illustrate our general claims in a concrete example where the Calabi-Yau manifold is explicitly described by toric geometry.

Quality stabilisation of synthetic sand containing bentonite in process lines

OpenAIRE

A. Fedoryszyn

2010-01-01

Stabilisation of sand quality requires the monitoring and control of sand moisture contents and its other parameters at each stage of sandprocessing, i.e. during the preparation of return sand mix and rebonding processes. Stabilisation of sand quality necessitates the use of reliable control equipment and evaluation procedures. This study outlines the scope and results of research work aimed to improve the control equipment to enhance the performance of turbine mixers. The paper reviews the m...

Release behavior of triazine residues in stabilised contaminated soils

International Nuclear Information System (INIS)

Ying, G.G.; Kookana, R.S.; Mallavarpu, M.

2005-01-01

This paper reports the release behavior of two triazines (atrazine and simazine) in stabilised soils from a pesticide-contaminated site in South Australia. The soils were contaminated with a range of pesticides, especially with triazine herbicides. With multiple extractions of each soil sample with deionised water (eight in total), 15% of atrazine and 4% of simazine residues were recovered, resulting in very high concentrations of the two herbicides in leachate. The presence of small fractions of surfactants was found to further enhance the release of the residues. Methanol content up to 10% did not substantially influence the concentration of simazine and atrazine released. The study demonstrated that while the stabilisation of contaminated soil with particulate activated carbon (5%) and cement mix (15%) was effective in locking the residues of some pesticides, it failed to immobilise triazine herbicides residues completely. Given the higher water solubility of these herbicides than other compounds more effective strategies to immobilise their residues is needed. - Stabilisation of contaminated soil with a mix of activated carbon and cement may fail to immobilise some contaminants like triazines

Security for whom? Stabilisation and civilian protection in Colombia.

Science.gov (United States)

Elhawary, Samir

2010-10-01

This paper focuses on three periods of stabilisation in Colombia: the Alliance for Progress (1961-73) that sought to stem the threat of communist revolution in Latin America; Plan Colombia and President Alvaro Uribe's 'democratic security' policy (2000-07) aimed at defeating the guerrillas and negotiating a settlement with the paramilitaries; and the current 'integrated approach', adopted from 2007, to consolidate more effectively the state's control of its territory.(1) The paper assesses the extent to which these stabilisation efforts have enhanced the protection of civilians and ultimately finds that in all three periods there has been a disconnect between the discourse and the practice of stabilisation. While they have all sought to enhance security, in actual fact, they have privileged the security of the state and its allies at the expense of the effective protection of the civilian population. This has not only led to widespread human rights abuses but also has undermined the long-term stability being pursued. © 2010 The Author(s). Journal compilation © Overseas Development Institute, 2010.

Steam-cured stabilised soil blocks for masonry construction

Energy Technology Data Exchange (ETDEWEB)

Venkatarama Reddy, B.V. [Indian Inst. of Science, Bangalore (India). Dept. of Civil Engineering; Lokras, S.S. [Indian Inst. of Science, Bangalore (India). ASTRA

1998-12-01

Energy-efficient, economical and durable building materials are essential for sustainable construction practices. The paper deals with production and properties of energy-efficient steam-cured stabilised soil blocks used for masonry construction. Problems of mixing expansive soil and lime, and production of blocks using soil-lime mixtures have been discussed briefly. Details of steam curing of stabilised soil blocks and properties of such blocks are given. A comparison of energy content of steam-cured soil blocks and burnt bricks is presented. It has been shown that energy-efficient steam cured soil blocks (consuming 35% less thermal energy compared to burnt clay bricks) having high compressive strength can be easily produced in a decentralised manner. (orig.)

Stabilisation of photo-multiplying gain; Stabilisation du gain des pbotomultiplicateurs

Energy Technology Data Exchange (ETDEWEB)

Tretiakoff, O; Bailly du Bois, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1956-07-01

The use of photomultiplier tubes in experimental physics is thwarted by their high responsiveness to changes in the feeding tension. Their use can be extended a great deal by a simple efficient stabilizing device which allows them to work in the same way as Geiger-Mueller tubes without losing the advantageous characteristics of photomultiplier tubes. (author) [French] L'utilisation des tubes photomultiplicateurs en physique experimentale se heurte a l'obstacle que constitue leur extreme sensibilite aux variations de la tension d'alimentation. Un systeme de stabilisation simple et efficace, permettant d'apparenter leurs caracteristiques a celles des compteurs Geiger-Muller tout en conservant les avantages propres aux tubes photomultiplicateurs, peut elargir considerablement leur domaine d'emploi. (auteur)

Stabilisering – fra intention til indsats

DEFF Research Database (Denmark)

Jacobsen, Katja Lindskov; Engen, Torben Toftgaard

Stabiliseringsindsatser udgør kun en mindre del af forsvarets samlede ressourcer. Ikke destomindre er stabilisering et vigtigt værktøj i bestræbelserne på at imødegå udfordringer fra syd.Udfordringer, der, hvis de ikke adresseres, kan risikere at få negative konsekvenser for dansksikkerhed. Denne...

Stability of yttria-stabilized zirconia during pyroprocessing tests

Energy Technology Data Exchange (ETDEWEB)

Choi, Eun-Young, E-mail: eychoi@kaeri.re.kr; Lee, Jeong; Lee, Sung-Jai; Kim, Sung-Wook; Jeon, Sang-Chae; Cho, Soo Haeng; Oh, Seung Chul; Jeon, Min Ku; Lee, Sang Kwon; Kang, Hyun Woo; Hur, Jin-Mok

2016-07-15

In this study, the feasibility of yttria-stabilized zirconia (YSZ) was investigated for use as a ceramic material, which can be commonly used for both electrolytic reduction and electrorefining. First, the stability of YSZ in salts for electrolytic reduction and electrorefining was examined. Then, its stability was demonstrated by a series of pyroprocessing tests, such as electrolytic reduction, LiCl distillation, electrorefining, and LiCl−KCl distillation, using a single stainless steel wire mesh basket containing fuel and YSZ. A single basket was used by its transportation from one test to subsequent tests without the requirements for unloading.

Solidification/stabilisation of liquid oil waste in metakaolin-based geopolymer

Energy Technology Data Exchange (ETDEWEB)

Cantarel, V.; Nouaille, F.; Rooses, A.; Lambertin, D., E-mail: david.lambertin@cea.fr; Poulesquen, A.; Frizon, F.

2015-09-15

Highlights: • Formulation with 20 vol.% of oil in a geopolymer have been successful tested. • Oil waste is encapsulated as oil droplets in metakaolin-based geopolymer. • Oil/geopolymer composite present good mechanical performance. • Carbon lixiviation of oil/geopolymer composite is very low. - Abstract: The solidification/stabilisation of liquid oil waste in metakaolin based geopolymer was studied in the present work. The process consists of obtaining a stabilised emulsion of oil in a water-glass solution and then adding metakaolin to engage the setting of a geopolymer block with an oil emulsion stabilised in the material. Geopolymer/oil composites have been made with various oil fraction (7, 14 and 20 vol.%). The rigidity and the good mechanical properties have been demonstrated with compressive strength tests. Leaching tests evidenced the release of oil from the composite material is very limited whereas the constitutive components of the geopolymer (Na, Si and OH{sup −}) are involved into diffusion process.

War, Peace and Stabilisation: Critically Reconceptualising Stability in Southern Afghanistan

Directory of Open Access Journals (Sweden)

William Robert Carter

2013-06-01

Full Text Available This article critically treats stabilisation theory and programming through a perspective of peace and conflict, and argues for stabilisation’s reconceptualisation. Through tracking the concept’s emergence, it outlines that stabilisation is theoretically rooted in an insecurity-underdevelopment problematic and relies on the Liberal Peace thesis as a solution. When this concept was operationalised in southern Afghanistan, however, it was translated into a praxis informed by state-building and counterinsurgency imperatives. This approach ultimately produced confused, sometimes counterproductive, effects: simultaneously engendering a liberal, negative, rented and victor’s peace. The article concludes by arguing that stabilisation should be reconceptualised so that it pursues a positive and hybrid peace if it is to be a more effective source of guidance for policy and practice. The first step is to denaturalise the ‘formal’ state in conflict and fragile environments as being seen as a panacea to all ills of instability.

The Effect of Humidity and Oxygen Partial Pressure on LSM–YSZ Cathode

DEFF Research Database (Denmark)

Knöfel, Christina; Chen, Ming; Mogensen, Mogens Bjerg

2011-01-01

Two series of anode supported solid oxide fuel cells (SOFC) were prepared, one with a composite cathode layer of lanthanum strontium manganite (LSM) and yttria stabilized zirconia (YSZ) on top and the other further has a LSM current collector layer on top. The fuel cells were heat treated at 1...... of manganese concentration and strontium enrichment on the surface of the materials. Formation of monoclinic zirconia and zirconate phases was also observed. These results give a closer insight into possible degradation mechanisms of SOFC composite cathode materials in dependence of humidity and oxygen partial...

β1 subunit stabilises sodium channel Nav1.7 against mechanical stress.

Science.gov (United States)

Körner, Jannis; Meents, Jannis; Machtens, Jan-Philipp; Lampert, Angelika

2018-06-01

The voltage-gated sodium channel Nav1.7 is a key player in neuronal excitability and pain signalling. In addition to voltage sensing, the channel is also modulated by mechanical stress. Using whole-cell patch-clamp experiments, we discovered that the sodium channel subunit β1 is able to prevent the impact of mechanical stress on Nav1.7. An intramolecular disulfide bond of β1 was identified to be essential for stabilisation of inactivation, but not activation, against mechanical stress using molecular dynamics simulations, homology modelling and site-directed mutagenesis. Our results highlight the role of segment 6 of domain IV in fast inactivation. We present a candidate mechanism for sodium channel stabilisation against mechanical stress, ensuring reliable channel functionality in living systems. Voltage-gated sodium channels are key players in neuronal excitability and pain signalling. Precise gating of these channels is crucial as even small functional alterations can lead to pathological phenotypes such as pain or heart failure. Mechanical stress has been shown to affect sodium channel activation and inactivation. This suggests that stabilising components are necessary to ensure precise channel gating in living organisms. Here, we show that mechanical shear stress affects voltage dependence of activation and fast inactivation of the Nav1.7 channel. Co-expression of the β1 subunit, however, protects both gating modes of Nav1.7 against mechanical shear stress. Using molecular dynamics simulation, homology modelling and site-directed mutagenesis, we identify an intramolecular disulfide bond of β1 (Cys21-Cys43) which is partially involved in this process: the β1-C43A mutant prevents mechanical modulation of voltage dependence of activation, but not of fast inactivation. Our data emphasise the unique role of segment 6 of domain IV for sodium channel fast inactivation and confirm previous reports that the intracellular process of fast inactivation can be

The Influence of Stabilisation on the Structure of Knits and Tensile Properties of Their Yarns

Directory of Open Access Journals (Sweden)

Rasa TREIGIENĖ

2012-12-01

Full Text Available Plated jersey knits of different composition were knitted and stabilised under hydrothermal conditions of 85 °C for 10, 20 or 30 min in steam ambience. The influence of stabilisation duration on knit structure was estimated as well as change of mechanical properties of the yarns. The obtained data show that 10 min of stabilisation influenced markedly the structure of plated jersey knits comparing with the same effect of 20 min and 30 min. The results of specific breaking force of polyester, cotton and wool yarns show decrease in their strength due to knitting and hydrothermal stabilisation processes.DOI: http://dx.doi.org/10.5755/j01.ms.18.4.3096

Synthesis and characterization of Yttria-stabilized-zirconia by spray pyrolysis

International Nuclear Information System (INIS)

Melo Halmenschlager, Cibele; Vieira, Ramaugusto; Shigueaki Takimi, Antonio; Lima da Silva, Aline; De Fraga Malfatti, Celia; Perez Bergmann, Carlos

2003-01-01

Yttria-stabilized-zirconia (YSZ) has been object of many studies due to its great chemical stability and excellent ionic conduction in high temperature. One of the applications of YSZ films is the use as electrolyte in solid oxide fuel cells (SOFC). The great challenge of the SOFC is the development of a intermediary temperature solid oxide fuel cell (ITSOFC) to work in a temperature around 700 o C with the same efficiency of high temperature SOFC, with this aim fuel cells utilizing thin electrolyte films ha been developed. Traditional techniques of thin films deposition as Combustion Vapour Deposition (CVD) and Sputtering are very expensive, the reagents must be very pure and it is necessary to use a system of vacuum. Spray pyrolysis is a good alternative to deposit dense films with thickness between 0,1 and 10 . This technique has a lot of advantages front to classic methods of deposition because of the simplicity of the process and the equipment, low cost, and minimal waste production. In this process, when the parameters are very well controlled, it is possible to obtain oxide films with high quality. In the present work, amorphous films consisted of a layer of 8 mol% Yttria-stabilized zirconia were produced by spray pyrolysis and heat treated to obtain crystalline films. The film was prepared with zirconium acetylacetonate (Zr(C 6 H 7 O 2 ) 4 ) and yttrium chloride (YCl 3 .6H 2 O), dissolved in ethanol (C 2 H 6 O) and diethylene glycol butyl ether (C 8 H 18 O 3 ) mixed in the volume ratio of 1:1, and a disk of steel 316L was used as substrate. The amorphous film was deposited in the substrate heat until 280 o C ± 50 o C and after deposition from thermal treatment at 700 o C, the amorphous film was changed into Yttria-stabilized-zirconia crystalline film. The precursor solution was characterized for the Differential Thermal Analysis (DTA). The morphology and crystallinity of the films was investigated by scanning electron microscopy (SEM) and X-ray diffraction

Yttria-Ceria stabilized tetragonal zirconia polycrystals: Sintering, grain growth and grain boundary segregation

NARCIS (Netherlands)

Boutz, M.M.R.; Boutz, M.M.R.; Winnubst, Aloysius J.A.; Burggraaf, Anthonie; Burggraaf, A.J.

1994-01-01

An analysis is presented of grain growth and densification of yttria-ceria stabilized tetragonal zirconia polycrystals (Y, Ce-TZPs) using both isothermal and non-isothermal techniques. The characteristics of Y, Ce-TZPs are compared to those of Y-TZP and Ce-TZP and the effect of increasing ceria

Process for the manufacture of a stabilized filament superconductor with a high proportion of stabilising material

International Nuclear Information System (INIS)

Both, R.; Hillmann, H.; Breuer, W.

1987-01-01

In order to manufacture superconductors with a high proportion of stabilising material, a compound body is first formed and is formed by extrusion and drawing to reduce its crossection. This compound body is then introduced into a sheath tube to increase the proportion of stabilising material and is formed to its final dimensions by further drawing processes. Tearing of the superconducting filaments is prevented by sufficient stabilising material (e.g. copper here) being introduced in the central area of the compound body. The filament superconductors can be manufactured at a reasonable price with a high proportion of stabilising material. (orig.) [de

Low-Temperature Superionic Conductivity in Strained Yttria-Stabilized Zirconia

DEFF Research Database (Denmark)

Sillassen, Michael; Eklund, Per; Pryds, Nini

2010-01-01

Very high lateral ionic conductivities in epitaxial cubic yttria-stabilized zirconia (YSZ) synthesized on single-crystal SrTiO3 and MgO substrates by reactive direct current magnetron sputtering are reported. Superionic conductivities (i.e., ionic conductivities of the order 1 -1cm-1) are observed...... at 500 °C for 58-nm-thick films on MgO. The results indicate a superposition of two parallel contributions - one due to bulk conductivity and one attributable to conduction along the film-substrate interface. Interfacial effects dominate the conductivity at low temperatures (...

Simulation model of a wind turbine pitch controller for grid frequency stabilisation

Energy Technology Data Exchange (ETDEWEB)

Jauch, Clemens; Cronin, Tom

2005-06-15

This paper describes a pitch angle controller that enables an active-stall wind turbine to dampen actively grid frequency oscillations. This builds on previous work in the area of the transient stability control of active-stall turbines. The phenomenon of grid frequency oscillations is explained briefly and then the task for the wind turbine controller defined. The pitch controller that acts as a grid frequency stabiliser is explained in terms of its layout, control sequence and parameters. Finally, a transient fault situation with subsequent grid frequency oscillations is simulated and it is shown how the grid frequency stabiliser works. The performance of the controller is discussed and the conclusion is drawn that grid frequency stabilisation with an active-stall turbine is possible under certain conditions. (Author)

Transformation Directions of the Financial Policy in the Process of Stabilisation of the Ukrainian Economy

OpenAIRE

Petrushevska Viktoriya V.

2013-01-01

The goal of the article is consideration of theoretical provisions with respect to the state financial policy. The article considers the role of the financial policy in ensuring stabilisation of the Ukrainian financial system. It presents conceptual provisions regarding main goals, mechanisms and instruments of the stabilisation financial policy of the state. It develops economic indicators of its efficiency. The use of indicators of economic efficiency of the stabilisation financial policy b...

Noise-cancelled, cavity-enhanced saturation laser spectroscopy for laser frequency stabilisation

International Nuclear Information System (INIS)

Vine, Glenn de; McClelland, David E; Gray, Malcolm B

2006-01-01

We employ a relatively simple experimental technique enabling mechanical-noise free, cavityenhanced spectroscopic measurements of an atomic transition and its hyperfine structure. We demonstrate this technique with the 532 nm frequency doubled output from a Nd:YAG laser and an iodine vapour cell. The resulting cavity-enhanced, noise-cancelled, iodine hyperfine error signal is used as a frequency reference with which we stabilise the frequency of the 1064nm Nd:YAG laser. Preliminary frequency stabilisation results are then presented

Stabilisation of clayey soils with high calcium fly ash and cement

Energy Technology Data Exchange (ETDEWEB)

S. Kolias; V. Kasselouri-Rigopoulou; A. Karahalios [National Technical University of Athens, Athens (Greece)

2005-02-01

The effectiveness of using high calcium fly ash and cement in stabilising fine-grained clayey soils (CL,CH) was investigated in the laboratory. Strength tests in uniaxial compression, in indirect (splitting) tension and flexure were carried out on samples to which various percentages of fly ash and cement had been added. Modulus of elasticity was determined at 90 days with different types of load application and 90-day soaked CBR values are also reported. Pavement structures incorporating subgrades improved by in situ stabilisation with fly ash and cement were analyzed for construction traffic and for operating traffic. These pavements are compared with conventional flexible pavements without improved subgrades and the results clearly show the technical benefits of stabilising clayey soils with fly ash and cement. In addition TG-SDTA and XRD tests were carried out on certain samples in order to study the hydraulic compounds, which were formed.

Microscopic mechanism of stability in yttria-doped zirconia

CERN Document Server

Ostanin, S A

2001-01-01

The relaxed configurations of yttria-stabilized zirconia (YSZ) between 3 and 10 mol. % Y sub 2 O sub 3 were modeled within the pseudopotential technique. The vibration mode corresponding to the soft phonon in pure c-ZrO sub 2 has been calculated for each Y sub 2 O sub 3 composition. These anharmonic vibrations, associated with stabilization of YSZ, have been investigated within the self-consistent phonon approximation that makes obtainable the fine structure in spectral density. In studying the phonon dynamics, it is proposed to use the displacement probability density which can quantify very accurately the transition temperature needed to stabilize the YSZ cubic phase

Lactose fermentation at Camembert, made by classic and stabilised

Directory of Open Access Journals (Sweden)

Bogdan Perko

2002-01-01

Full Text Available In our experiments the fermentation of lactose at Camembert type cheese by classic and stabilised technology was monitored. In each of the two technologies two experiments were made. The difference between these two technologies is in pH level, which drops below 5 by classic technology and remains above 5 by stabilised technology at all times. To achieve the criteria of stabilised technology the fermentation was stopped at a desired level of pH, by dropping the cheese in brine at 14 °C. After salting and moulding cheesewas transferred from the first three experiments into a ripening chamber at 11 °C. With the last experiment (stabilised technology the cheese ripened for 3 days at 5 °C. During ripening process pH dropped below 5 in all experiments. The process of fermentation was performed by the following lactic acid bacteria: Streptococcus thermophilus, Lactococcus lactis subsp. lactis and Lactococcus lactis subsp. cremoris. As these lactic acid bacteria ferment differently D-galactose during manufacture and ripening process, the contentof lactose and D-galactose was measured. Based on the results of our research the following conclusion can be made: the action of lactic acid bacteria can not be stropped even at 5 °C. The native microflora, which remains in the milk after thermisation, might be responsible for the fermentation of Dgalactose. It could be possible that the Streptococcus thermophilus enzymes were not inactivated, causing continuation of lactose fermentation even at low temperature. Mesophilic lactococci were inhibited and for that reason Dgalactose accumulated in cheese. Only after cheese were transferred into a ripening chamber at 11 °C and with low lactose concentration in medium left, mesophilic lactococci started to ferment D-galactose.

A complete characterisation of All-versus-Nothing arguments for stabiliser states

OpenAIRE

Abramsky, Samson; Barbosa, Rui Soares; Carù, Giovanni; Perdrix, Simon

2017-01-01

An important class of contextuality arguments in quantum foundations are the All-versus-Nothing (AvN) proofs, generalising a construction originally due to Mermin. We present a general formulation of All-versus-Nothing arguments, and a complete characterisation of all such arguments which arise from stabiliser states. We show that every AvN argument for an n-qubit stabiliser state can be reduced to an AvN proof for a three-qubit state which is local Clifford-equivalent to the tripartite GHZ s...

Quality and correlates of specific self-esteem at the beginning stabilisation phase of schizophrenia.

Science.gov (United States)

Wittorf, Andreas; Wiedemann, Georg; Buchkremer, Gerhard; Klingberg, Stefan

2010-09-30

In view of the potential importance of self-esteem in schizophrenia, there is a considerable lack of knowledge about the characteristics of specific self-esteem. The literature suggests that the experience of the self might be particularly destabilised in the transition phase between acute and remission points of the illness. Thus, the present study aims at examining the quality and correlates of different self-concepts at the beginning stabilisation phase of schizophrenia. In this study, 135 patients with schizophrenia were assessed 3 weeks after admission to inpatient treatment. Four central self-concepts were measured by the Frankfurt Self-Concept Scales (FSKN; Deusinger, I.M., 1986, Die Frankfurter Selbstkonzeptskalen (FSKN), Göttingen, Hogrefe). Clinical psychopathologic, neuropsychological and sociodemographic factors were analysed in two-step exploratory correlation and regression analyses to determine their relative contribution to self-concepts. The median of the four self-concepts ranged between -0.9 and -1.4 standard deviations below normative level. The relationship between negative symptoms and self-concepts was consistently significant, even when the contribution of depression was partialed out. In the multivariate analyses, these two symptom clusters explained up to 39% of the variances in our patients' self-evaluation. Neuropsychological dysfunctions were of relatively subordinate relevance for the patients' self-concepts. Thus, our results suggest that specific self-esteem at the point of beginning stabilisation of schizophrenia is significantly confounded not only by depression but also by negative symptoms. Copyright © 2009 Elsevier Ireland Ltd. All rights reserved.

A comparative crystallographic analysis of the tetragonal-to-monoclinic transformation in the yttria-zirconia system

Science.gov (United States)

Navruz, N.

2008-06-01

The various requirements for effective transformation toughening cannot be predicted without a detailed understanding of the crystallography of the martensitic transformation. In this connection, a comparative crystallographic analysis for four pairs of lattice-correspondence variants in the yttria-zirconia system has been performed on the basis of infinitesimal-deformation (ID) approach and Wechsler-Lieberman-Read (WLR) crystallographic theory. A comparison of the crystallographic features obtained from these two theories was made. In order to verify the applicability of the two theories to this transformation, the calculated results were also compared with the experimental data available. The present study shows that the predictions of both the ID approach and the WLR crystallographic theory can provide data necessary for the model of transformation toughening and act as a guideline for the experimental work in the yttria-zirconia system.

Self-Stabilising Quadrupedal Running by Mechanical Design

Directory of Open Access Journals (Sweden)

Panagiotis Chatzakos

2009-01-01

Full Text Available Dynamic stability allows running animals to maintain preferred speed during locomotion over rough terrain. It appears that rapid disturbance rejection is an emergent property of the mechanical system. In running robots, simple motor control seems to be effective in the negotiation of rough terrain when used in concert with a mechanical system that stabilises passively. Spring-like legs are a means for providing self-stabilising characteristics against external perturbations. In this paper, we show that a quadruped robot could be able to perform self-stable running behaviour in significantly broader ranges of forward speed and pitch rate with a suitable mechanical design, which is not limited to choosing legs spring stiffness only. The results presented here are derived by studying the stability of the passive dynamics of a quadruped robot running in the sagittal plane in a dimensionless context and might explain the success of simple, open loop running controllers on existing experimental quadruped robots. These can be summarised in (a the self-stabilised behaviour of a quadruped robot for a particular gait is greatly related to the magnitude of its dimensionless body inertia, (b the values of hip separation, normalised to rest leg length, and leg relative stiffness of a quadruped robot affect the stability of its motion and should be in inverse proportion to its dimensionless body inertia, and (c the self-stable regime of quadruped running robots is enlarged at relatively high forward speeds. We anticipate the proposed guidelines to assist in the design of new, and modifications of existing, quadruped robots. As an example, specific design changes for the Scout II quadruped robot that might improve its performance are proposed.

On matrix stabilisation of d- and f-transition metal ions in unstable oxidation states

Energy Technology Data Exchange (ETDEWEB)

Kiselev, Yurii M [Department of Chemistry, M.V. Lomonosov Moscow State University, Moscow (Russian Federation)

2009-01-31

The state-of-the-art in matrix stabilisation of d- and f-transition metal ions in unstable oxidation states is analysed. Main aspects of this problem concerning the genealogy of appropriate matrix systems are classified. Relevant examples are given and the data that contradict the scheme proposed are discussed. The thermodynamics of the matrix stabilisation effect is considered using the concept of isomorphic miscibility. The influence of defects and non-equilibrium on the matrix stabilisation effect is discussed. The problem of identification of the oxidation states in matrix systems is examined and various types of matrix systems are considered.

On matrix stabilisation of d- and f-transition metal ions in unstable oxidation states

International Nuclear Information System (INIS)

Kiselev, Yurii M

2009-01-01

The state-of-the-art in matrix stabilisation of d- and f-transition metal ions in unstable oxidation states is analysed. Main aspects of this problem concerning the genealogy of appropriate matrix systems are classified. Relevant examples are given and the data that contradict the scheme proposed are discussed. The thermodynamics of the matrix stabilisation effect is considered using the concept of isomorphic miscibility. The influence of defects and non-equilibrium on the matrix stabilisation effect is discussed. The problem of identification of the oxidation states in matrix systems is examined and various types of matrix systems are considered.

Growth kinetics of tetragonal and monoclinic ZrO2 crystallites in 3 mol% yttria partially stabilized ZrO2 (3Y-PSZ) precursor powder

International Nuclear Information System (INIS)

Kuo, Chih-Wei; Lee, Kuen-Chan; Yen, Feng-Lin; Shen, Yun-Hwei; Lee, Huey-Er; Wen, Shaw-Bing; Wang, Moo-Chin; Stack, Margaret Mary

2014-01-01

Highlights: • The crystalline structures were composed of tetragonal and monoclinic ZrO 2 . • Growth kinetics of t-ZrO 2 in the 3Y-PSZ precursor powder is described as: D te 2 =(4.57±0.55)t 0.12±0.02 exp(-((24.79±0.38)×10 3 )/(RT) ). • Growth kinetics of m-ZrO 2 in the 3Y-PSZ precursor powder is described as: D m 2 =(4.40±1.63)t 0.17±0.08 exp(-((66.47±3.97)×10 3 )/(RT) ). - Abstract: The growth kinetics of tetragonal and monoclinic ZrO 2 crystallites in 3 mol% yttria partially stabilized ZrO 2 (3Y-PSZ) precursor powder has been investigated using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) specific surface area analysis, transmission electron microscopy (TEM) and high resolution TEM (HRTEM). After calcination of the 3Y-PSZ precursor powder between 773 and 1073 K for 2 h, the crystalline structures were composed of tetragonal and monoclinic ZrO 2 as the primary and secondary phases, respectively. When the 3Y-PSZ precursor powder was calcined at 773 K for 2 h, the BET specific surface area was 97.13 m 2 /g, which is equivalent to a particle size of 10.30 nm. The crystallite sizes determined via XRD and BET agreed well, indicating that the powder was virtually non-agglomerated. The growth kinetics of tetragonal and monoclinic ZrO 2 crystallite isothermal growth in the 3Y-PSZ precursor powder are described by: D te 2 =(4.57±0.55)t 0.12±0.02 exp(-((24.79±0.38)×10 3 )/(RT) ) and D m 2 =(4.40±1.63)t 0.17±0.08 exp(-((66.47±3.97)×10 3 )/(RT) ), respectively, for 773K≤T≤1073K. D te and D m denote the crystallite size of tetragonal and monoclinic ZrO 2 at time t and temperature T, respectively

Management, stabilisation and environmental impact of uranium mill tailings

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

These proceedings deal with the sources of radioactivity arising from uranium mill wastes, the environmental aspects, the management and stabilisation of radioactive wastes and the policies and regulatory aspects.

Management, stabilisation and environmental impact of uranium mill tailings

International Nuclear Information System (INIS)

1978-01-01

These proceedings deal with the sources of radioactivity arising from uranium mill wastes, the environmental aspects, the management and stabilisation of radioactive wastes and the policies and regularoty aspects

Yttria hydroxy-salt binders

International Nuclear Information System (INIS)

Holcombe, C.E. Jr.

1978-01-01

Binder phase (primarily chloride or nitrate) formation was examined in YX 3 --NaOH--H 2 O, Y 2 O 3 --acid--H 2 O, and Y 2 O 3 --salt--H 2 O systems. The cementitious phase consisted mostly of plate- (or needle-) shaped hydroxy salts of the general formula Y 2 (OH)/sub 6-m/X/sub m/ nH 2 O, where m and n normally equal one. These binders were examined by x-ray diffraction and thermal analysis techniques. Nitrate binders decompose to Y 2 O 3 by 600 0 C, whereas chloride binders form oxychlorides that sublime or convert to Y 2 O 3 after oxygen replacement of chlorine (in air) at > 1000 0 C. Although nitric and hydrochloric acid solutions form porous ( 2 O 3 powder, salt solutions (i.e., NH 4 NO 3 , Mg(NO 3 ) 2 , NH 4 Cl, and YCl 3 approx. = 6H 2 O) slow the reaction considerably (48 h to 4 weeks), allowing 70- to 80%-dense cements to form. The effects of formation conditions on physical properties of binders were studied. Examination of scandium and lanthanide oxides showed that several behave in the same way as yttria

Effects of electron beam irradiation on the property behaviour of poly(ether-block-amide) blended with various stabilisers

International Nuclear Information System (INIS)

Murray, Kieran A.; Kennedy, James E.; Barron, Valerie; McEvoy, Brian; Vrain, Olivier; Ryan, Damien; Cowman, Richard; Higginbotham, Clement L.

2015-01-01

Radiosterilisation can induce modifications and/or degradation to transpire in poly(ether-block-amide) (PEBA) following irradiation. The current investigation utilises combined synergistic mixtures of stabilisers to minimise these effects, by melt blending them with the PEBA material. Hindered amine stabilisers (HAS), primary antioxidants and secondary antioxidants were the stabilisers incorporate to reduce/eliminate the effects of 50 kGy electron beam irradiation dose on the material. Results were discussed by comparing the stabilising efficiency of mixtures on the PEBA material in contrast to the control sample. Dynamic frequency sweeps demonstrated the formation of crosslinks, where the degree of crosslinking was dependent on the combination of stabilisers mixed in the base material (PEBA). The storage modulus displayed that PEBA blended with Irganox 565 had very slight changes in contrast to all other samples following irradiation. However, since this sample is a phenol containing system, severe discolouration was observed in comparison to other samples due to the oxidation of the hindered phenol. Overall, this study provides compelling evidence that a combined synergistic mixture of Irganox 565 (multifunctional phenolic antioxidant) and Tinuvin 783 (hindered amide light stabiliser) with PEBA, resulted in the best radiation stability. - Highlights: • PEBA was melt blended with various stabilisers. • All virgin and blended PEBA samples were exposed to electron beam irradiation. • The incorporation of stabilisers into the PEBA material resulted in discolouration. • PEBA blended with Irganox 565 and Tinuvin 783 improved the radiation resistance

Nordic regionalisation of a greenhouse-gas stabilisation scenario

Energy Technology Data Exchange (ETDEWEB)

Wyser, Klaus; Rummukainen, Markku; Strandberg, Gustav

2006-10-15

The impact of a CO{sub 2} stabilisation on the Swedish climate is investigated with the regional climate model RCA3 driven by boundary conditions obtained from a global coupled climate system model (CCSM3). The global model has been forced with observed greenhouse gas concentrations from pre-industrial conditions until today's, and with an idealised further increase until the stabilisation level is reached. After stabilisation the model integration continues for another 150+ years in order to follow the delayed response of the climate system over a period of time. Results from the global and regional climate model are compared against observations and ECMWF reanalysis for 1961-1990. For this period, the global model is found to be too cold over Europe and with a zonal flow from the North Atlantic towards Europe that is too strong. The climate of the driving global model controls the climate of the regional model and the same deviations from one are thus inherited by the other. We therefore analyse the relative climate changes differences, or ratios, of climate variables between future's and today's climate. Compared to pre-industrial conditions, the global mean temperature changes by about 1.5 deg C as a result of the stabilisation at 450 ppmv equivalent CO{sub 2}. Averaged over Europe, the temperature change is slightly larger, and it is even larger for Sweden and Northern Europe. Annual mean precipitation for Europe is unaffected, but Sweden receives more precipitation under higher CO{sub 2} levels. The inter-annual and decadal variability of annual mean temperature and precipitation does not change with any significant degree. The changes in temperature and precipitation are not evenly distributed with the season: the largest warming and increased precipitation in Northern Europe occurs during winter months while the summer climate remains more or less unchanged. The opposite is true for the Mediterranean region where the precipitation decreases

Laser stabilisation for velocity-selective atomic absorption

NARCIS (Netherlands)

Meijer, H.A.J.; Meulen, H.P. van der; Ditewig, F.; Wisman, C.J.; Morgenstern, R.

1987-01-01

A relatively simple method is described for stabilising a dye laser at a frequency ν = ν0 + νc in the vicinity of an atomic resonance frequency ν0. The Doppler effect is exploited by looking for atomic fluorescence when a laser beam is crossed with an atomic beam at certain angles αi. Absolute

Joining of yttria-tetragonal zirconia polycrystal with an aluminum-zirconium alloy

International Nuclear Information System (INIS)

Rathner, R.C.; Green, D.J.

1990-01-01

Specimens of yttria-tetragonal zirconia polycrystal (Y-TZP) have been joined with an Al-5.8 wt% Zr alloy at temperatures of 900 degrees C and above. The braze alloy contained large needlelike precipitates of the intermetallic phase Al 3 Sr. It is shown that these large precipitates can aid in strengthening of the joint, especially if they are close to the interface. With decreasing layer thickness, the strengths increased with values as high as 420 MPa

Stabilising the global greenhouse. A simulation model

International Nuclear Information System (INIS)

Michaelis, P.

1993-01-01

This paper investigates the economic implications of a comprehensive approach to greenhouse policies that strives to stabilise the atmospheric concentration of greenhouse gases at an ecolocially determined threshold level. In a theoretical optimisation model conditions for an efficient allocation of abatement effort among pollutants and over time are derived. The model is empirically specified and adapted to a dynamic Gams-algorithm. By various simulation runs for the period of 1990 to 2110, the economics of greenhouse gas accumulation are explored. In particular, the long-run cost associated with the above stabilisation target are evaluated for three different policy scenarios: i) A comprehensive approach that covers all major greenhouse gases simultaneously, ii) a piecemeal approach that is limited to reducing CO 2 emissions, and iii) a ten-year moratorium that postpones abatement effort until new scientific evidence on the greenhouse effect will become available. Comparing the simulation results suggests that a piecemeal approach would considerably increase total cost, whereas a ten-year moratorium might be reasonable even if the probability of 'good news' is comparatively small. (orig.)

Electrochemical behaviour of ceramic yttria stabilized zirconia on carbon steel synthesized via sol-gel process

International Nuclear Information System (INIS)

Crespo, M.A. Dominguez; Murillo, A. Garcia; Torres-Huerta, A.M.; Yanez-Zamora, C.; Carrillo-Romo, F. de J

2009-01-01

Chromate conversion coatings have been widely applied for the corrosion of different metallic substrates. However, the waste containing Cr 6+ has many limitations due to the environmental consideration and health hazards. An interesting alternative seems to be the deposition on metallic surface of thin layers of yttria or zirconia or both by the sol-gel process. In this study, Ytttria and Yttria stabilized zirconia (YSZ, 8% Y 2 O 3 ) thin films were used for coating commercial carbon steel substrates by sol-gel method and the dip-coating process. The evolution of organic compounds up to crystallization process as a function of heat treatments was study by FT-IR spectroscopy. The structure and morphology of the coatings were analysed using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The anticorrosion performance of the coatings has been evaluated by using electrochemical techniques in an aggressive media (3.5 wt.% NaCl). The corrosion behaviour of sol-gel method was compared with traditional chromate conversion coatings. Differences in the electrochemical behaviour of YSZ coatings are related to the development of microcracks during the sintering process and to the presence of organic compounds during growth film. Electrochemical results showed that sol-gel YSZ and Y 2 O 3 coatings can act as protective barriers against wet corrosion; however yttria films displayed low adhesion to substrate. The corrosion parameters provide an explanation of the role of each film and show a considerable increase in the corrosion resistance for coated samples in comparison to the bare steel samples.

Electrochemical behaviour of ceramic yttria stabilized zirconia on carbon steel synthesized via sol-gel process

Energy Technology Data Exchange (ETDEWEB)

Crespo, M.A. Dominguez, E-mail: mdominguezc@ipn.m [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Altamira (CICATA-IPN) km 14.5 Carr. Tampico-Puerto Industrial, C.P. 89600, Altamira, Tamaulipas (Mexico); Murillo, A. Garcia; Torres-Huerta, A.M. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Altamira (CICATA-IPN) km 14.5 Carr. Tampico-Puerto Industrial, C.P. 89600, Altamira, Tamaulipas (Mexico); Yanez-Zamora, C. [Estudiante del postgrado en Tecnologia Avanzada del CICATA-IPN, Unidad Altamira, km 14.5, Carr. Tampico-Puerto Industrial. C.P. 89600, Altamira, Tamaulipas (Mexico); Carrillo-Romo, F. de J [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Altamira (CICATA-IPN) km 14.5 Carr. Tampico-Puerto Industrial, C.P. 89600, Altamira, Tamaulipas (Mexico)

2009-08-26

Chromate conversion coatings have been widely applied for the corrosion of different metallic substrates. However, the waste containing Cr{sup 6+} has many limitations due to the environmental consideration and health hazards. An interesting alternative seems to be the deposition on metallic surface of thin layers of yttria or zirconia or both by the sol-gel process. In this study, Ytttria and Yttria stabilized zirconia (YSZ, 8% Y{sub 2}O{sub 3}) thin films were used for coating commercial carbon steel substrates by sol-gel method and the dip-coating process. The evolution of organic compounds up to crystallization process as a function of heat treatments was study by FT-IR spectroscopy. The structure and morphology of the coatings were analysed using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The anticorrosion performance of the coatings has been evaluated by using electrochemical techniques in an aggressive media (3.5 wt.% NaCl). The corrosion behaviour of sol-gel method was compared with traditional chromate conversion coatings. Differences in the electrochemical behaviour of YSZ coatings are related to the development of microcracks during the sintering process and to the presence of organic compounds during growth film. Electrochemical results showed that sol-gel YSZ and Y{sub 2}O{sub 3} coatings can act as protective barriers against wet corrosion; however yttria films displayed low adhesion to substrate. The corrosion parameters provide an explanation of the role of each film and show a considerable increase in the corrosion resistance for coated samples in comparison to the bare steel samples.

Thermoanalytical study of the formation mechanism of yttria from yttrium acetate

International Nuclear Information System (INIS)

Farjas, J.; Camps, J.; Roura, P.; Ricart, S.; Puig, T.; Obradors, X.

2011-01-01

Highlights: → Thermal decomposition of yttrium acetate: three endothermic stages. → Intermediates: yttrium hydroxide and carbonate. → Product: cubic yttria (the degree of transformation is at least 99%). → The decomposition does not depend on the oxygen partial pressure. - Abstract: The processes involved in the thermal decomposition of yttrium acetate tetrahydrate, Y(CH 3 COO) 3 .4H 2 O, in air and in an inert atmosphere have been analyzed by thermoanalytical techniques (thermogravimetry, differential thermal analysis and evolved gas analysis) and by the structural characterization (X-ray diffraction, infrared spectroscopy, elemental analysis and scanning electron microscopy) of intermediates and final products. Decomposition of yttrium acetate is an endothermic transformation that takes place in a temperature range between 350 and 900 o C. The evolution of the mass during the decomposition process is not affected by the presence of oxygen. The process is initiated by the rupture of the bond between the metallic cation and the acetate ligand. This initial step (350-450 o C) involves the formation of amorphous yttrium hydroxide and yttrium carbonate and is characterized by a fast mass loss rate. A sudden decrease of the mass loss rate indicates a change in the decomposition kinetics that continues with the decomposition of yttrium hydroxide and yttrium carbonate. The main effect of an oxygen atmosphere is an intense exothermic process due to the combustion of organic species in the gas phase.

Intensity stabilisation of optical pulse sequences for coherent control of laser-driven qubits

Science.gov (United States)

Thom, Joseph; Yuen, Ben; Wilpers, Guido; Riis, Erling; Sinclair, Alastair G.

2018-05-01

We demonstrate a system for intensity stabilisation of optical pulse sequences used in laser-driven quantum control of trapped ions. Intensity instability is minimised by active stabilisation of the power (over a dynamic range of > 104) and position of the focused beam at the ion. The fractional Allan deviations in power were found to be logic gates to be below 10^{-6} per gate.

Structural evolution of plasma-sprayed nanoscale 3 mol% and 5 mol% yttria-stabilized zirconia coatings during sintering

Science.gov (United States)

Zhao, Yan; Gao, Yang

2017-12-01

The microstructure of plasma-sprayed nanostructured yttria-stabilized zirconia (YSZ) coatings may change during high-temperature exposure, which would influence the coating performance and service lifetime. In this study, the phase structure and the microstructural evolution of 3YSZ (zirconia-3 mol% yttria) and 5YSZ (zirconia-5 mol% yttria) nanostructured coatings were investigated by means of sintering at 1400 °C for 50-100 h. The microhardness, elastic moduli, and thermal shock cycles of the 3YSZ and 5YSZ nanostructured coatings were also investigated. The results showed that the redistribution of yttrium ions at 1400 °C caused the continuous increase of monoclinic-phase zirconia, but no obvious inter-splat cracking formed at the cross-sections, even after 100 h. Large voids appeared around the nanoporous zone because of the sintering of nanoscale granules upon high-temperature exposure. The microhardness and elastic moduli of the nanostructured coatings first increased and then decreased with increasing sintering times. The growth rate of the nanograins in the 3YSZ coating was lower than that in 5YSZ, which slowed the changes in 3YSZ coating porosity during sintering. Although the 3YSZ coating was prone to monoclinic phase transition, the experimental results showed that the thermal shock resistance of the 3YSZ coating was better than that of the 5YSZ coating.

Evaluation of bonding strength between yttria coating and vanadium alloys for development of self-cooled blanket

Energy Technology Data Exchange (ETDEWEB)

Akamatsu, Hitoshi, E-mail: akamatsu@jupiter.qse.tohoku.ac.jp [Department of Quantum Science and Energy Engineering, Tohoku University, 6-6-01-2, Aramaki-aza-Aoba, Sendai 980-8579 (Japan); Satou, Manabu; Sato, Takashi [Department of Quantum Science and Energy Engineering, Tohoku University, 6-6-01-2, Aramaki-aza-Aoba, Sendai 980-8579 (Japan); Jain, Amit; Gupta, Vijay [Department of Mechanical and Aerospace Engineering, 38-137E, Eng IV Building, University of California, Los Angels, CA 90095-1597 (United States); Hasegawa, Akira [Department of Quantum Science and Energy Engineering, Tohoku University, 6-6-01-2, Aramaki-aza-Aoba, Sendai 980-8579 (Japan)

2011-10-01

A laser spallation technique was utilized for measurement of the bonding strength between yttria coating and vanadium alloys. The bonding strength between the alloys containing small amounts of yttrium made by levitation melting method and the yttria coating prepared by vacuum plasma-spray was evaluated to be about 950 MPa. It was not clearly observed the effects of alloying elements on the bonding strength. The strength varied about 100 MPa by specimens and by alloy compositions. Detailed observation of the failure type at the interface indicated that crack formation in the coating reduced the stress at the interface, so that the evaluation might be overestimated. It was demonstrated that application of the laser spallation technique to measure the bonding strength between ceramics coating and base material was useful for the evaluation of mechanical integrity of the coating.

Experimental Investigations of Decentralised Control Design for The Stabilisation of Rotor-Gas Bearings

DEFF Research Database (Denmark)

Theisen, Lukas Roy Svane; Galeazzi, Roberto; Niemann, Hans Henrik

2015-01-01

frequencies. Active lubrication of the journal during operations could enhance the damping and stabilisation characteristics of the sytems, and this could be achieved by means of stabilising controllers. This paper investigates the feasibility of using reduced order models obtained through Grey......-Box identification for the design of stabilising controllers, capable of enabling the active lubrication of the journal. The root locus analysis shows that two different control solutions are feasible for the dampening of the first two eigenfrequencies of the rotor-gas bearing in the horizontal and vertical...... directions. Hardening and softening P-lead controllers are designed based on the models experimentally identified, and salient features of both controllers are discussed. Both controllers are implemented and validated on the physical test rig. Experimental results confirm the validity of the proposed...

Microstructure and thermal stability of Fe, Ti and Ag implanted Yttria-stabilized zirconia

NARCIS (Netherlands)

van Hassel, B.A.; van Hassel, B.A.; Burggraaf, Anthonie; Burggraaf, A.J.

1991-01-01

Yttria-stabilized zirconia (YSZ) was implanted with 15 keV Fe or Ti ions up to a dose of 8×1016 at cm−2. The resulting “dopant” concentrations exceeded the concentrations corresponding to the equilibrium solid solubility of Fe2O3 or TiO2 in YSZ. During oxidation in air at 400° C, the Fe and Ti

Optimisation of bitumen emulsion properties for ballast stabilisation

International Nuclear Information System (INIS)

D’Angelo, G.; Lo Presti, D.; Thom, N.

2017-01-01

Ballasted track, while providing economical and practical advantages, is associated with high costs and material consumption due to frequent maintenance. More sustainable alternatives to conventional ballasted trackbeds should therefore aim at extending its durability, particularly considering ongoing increases in traffic speed and loads. In this regard, the authors have investigated a solution consisting of bitumen stabilised ballast (BSB), designed to be used for new trackbeds as well as in reinforcing existing ones. This study presents the idea behind the technology and then focuses on a specific part of its development: the optimisation of bitumen emulsion properties and dosage in relation to ballast field conditions. Results showed that overall bitumen stabilisation improved ballast resistance to permanent deformation by enhancing stiffness and damping properties. Scenarios with higher dosage of bitumen emulsion, higher viscosity, quicker setting behaviour, and harder base bitumen seem to represent the most desirable conditions to achieve enhanced in-field performance. [es

Transformation Directions of the Financial Policy in the Process of Stabilisation of the Ukrainian Economy

Directory of Open Access Journals (Sweden)

Petrushevska Viktoriya V.

2013-11-01

Full Text Available The goal of the article is consideration of theoretical provisions with respect to the state financial policy. The article considers the role of the financial policy in ensuring stabilisation of the Ukrainian financial system. It presents conceptual provisions regarding main goals, mechanisms and instruments of the stabilisation financial policy of the state. It develops economic indicators of its efficiency. The use of indicators of economic efficiency of the stabilisation financial policy by the bodies of state authority in their practical activity would provide the society with a possibility to assess expediency of measures of this policy increasing its efficiency and decreasing criticism at the government. A necessary direction of achievement of effectiveness and efficiency of the stabilisation financial policy is taking into consideration interests of all social groups (population, entrepreneurs, financial institutes and companies, etc. by the bodies of state authority in the process of its development and realisation.

Stabilisation of spent mushroom substrate for application as a plant growth-promoting organic amendment.

Science.gov (United States)

Paula, Fabiana S; Tatti, Enrico; Abram, Florence; Wilson, Jude; O'Flaherty, Vincent

2017-07-01

Over three million tonnes of spent mushroom substrate (SMS) are produced in Europe every year as a by-product of the cultivation of Agaricus bisporus. The management of SMS has become an increasing challenge for the mushroom production industry, and finding environmentally and economically sustainable solutions for this organic residue is, therefore, highly desirable. Due to its physical properties and nutrient content, SMS has great potential to be employed in agricultural and horticultural sectors, and further contribute to reduce the use of non-renewable resources, such as peat. However, SMS is often regarded as not being stable and/or mature, which hampers its wide use for crop production. Here, we demonstrate the stabilisation of SMS and its subsequent use as organic fertiliser and partial peat replacement in horticulture. The stabilisation was performed in a laboratory-scale composting system, with controlled temperature and aeration. Physical and chemical parameters were monitored during composting and provided information on the progress of the process. Water soluble carbohydrates (WSC) content was found to be the most reliable parameter to predict SMS stability. In situ oxygen consumption indicated the main composting phases, reflecting major changes in microbial activity. The structure of the bacterial community was also found to be a potential predictor of stability, as the compositional changes followed the composting progress. By contrast, the fungal community did not present clear successional process along the experiment. Maturity and quality of the stabilised SMS were assessed in a horticultural growing trial. When used as the sole fertiliser source, SMS was able to support Lolium multiflorum (Italian ryegrass) growth and significantly improved grass yield with a concentration-dependent response, increasing grass biomass up to 300%, when compared to the untreated control. In summary, the results indicated that the method employed was efficient in

Design of a wind turbine pitch angle controller for power system stabilisation

Energy Technology Data Exchange (ETDEWEB)

Jauch, Clemens; Soerensen, Poul [Risoe National Laboratory, Wind Energy Department, P.O. Box 49, DK-4000 Roskilde (Denmark); Islam, Syed M. [Department of Electrical and Computer Engineering, Curtin University of Technology, GPO Box U1987, Perth, WA 6845 (Australia); Bak Jensen, Birgitte [Institute of Energy Technology, Aalborg University, Pontoppidanstraede 101, DK-9220 Aalborg East (Denmark)

2007-11-15

The design of a PID pitch angle controller for a fixed speed active-stall wind turbine, using the root locus method is described in this paper. The purpose of this controller is to enable an active-stall wind turbine to perform power system stabilisation. For the purpose of controller design, the transfer function of the wind turbine is derived from the wind turbine's step response. The performance of this controller is tested by simulation, where the wind turbine model with its pitch angle controller is connected to a power system model. The power system model employed here is a realistic model of the North European power system. A short circuit fault on a busbar close to the wind turbine generator is simulated, and the dynamic responses of the system with and without the power system stabilisation of the wind turbines are presented. Simulations show that in most operating points the pitch controller can effectively contribute to power system stabilisation. (author)

Stabilising a victor's peace? Humanitarian action and reconstruction in eastern Sri Lanka.

Science.gov (United States)

Goodhand, Jonathan

2010-10-01

This paper focuses on the 'Sri Lankan model' of counter-insurgency and stabilisation and its implications for humanitarian and development actors. The Sri Lanka case shows that discourses, policies and practices associated with 'stabilisation' are not confined to 'fragile state' contexts in which there is heavy (and often militarised) international engagement--even though exemplars such as Afghanistan and Iraq have tended to dominate debates on this issue. Rather than being a single template, the 'stabilisation agenda' takes on very different guises in different contexts, presenting quite specific challenges to humanitarian and development actors. This is particularly true in settings like Sri Lanka, where there is a strong state, which seeks to make aid 'coherent' with its own vision of a militarily imposed political settlement. Working in such environments involves navigating a highly-charged domestic political arena, shaped by concerns about sovereignty, nationalism and struggles for legitimacy. © 2010 The Author(s). Journal compilation © Overseas Development Institute, 2010.

Small-State Special Operations in a Comprehensive Stabilisation Context

DEFF Research Database (Denmark)

Johnsen, Anton Asklund

takeaways were: Special operations as a force multiplier: Can special operations enable other stabilisation agents, locals as well as internationals, to accomplish their missions more effectively? This includes NGOs, diplomats or other officials, other military units, etc. How can the mindset required...... to enable ‘whole-of-government’ approaches be promoted? Economy of force considerations: Are special operations truly a cheaper means of reaching certain ends? When are small and indirect approaches involving special operations forces effective and when are they not? Special operations as expansion......“Small-State Special Operations in a Comprehensive Stabilisation Context: What to Know and Where to Go?” was the headline of a conference held at the Royal Danish Defence College, facilitated by the Institute for Strategy. As a product of this conference, a report has been written which highlights...

Hydrogen Solubility in Pr-doped and Un-doped YSZ for One Chamber Fuel Cell

DEFF Research Database (Denmark)

Bay, Lasse; Horita, T.; Sakai, N.

1998-01-01

SIMS analysis. Doping of Pr in the YSZ resulted in a higher intensity of the D ion, which indicated that hydrogen solubility was raised by the doping. The solubility of hydrogen in the electrolyte may affect the performance of one chamber fuel cells. (C) 1998 Elsevier Science B.V. All rights reserved.......Yttria-stabilised zirconia electrolytes (YSZ and Pr-doped YSZ) and yttria-doped strontium cerate (SYC) were tested in a one chamber fuel cell fed with a mixture of methane and air at 1223 K. The obtained performances were 4 mW cm(-2), 3 mW cm(-2), 2.5 mW cm(-2), and 0.15 mW cm(-2) for SYC, 1.8 mol...

Time course of the acute effects of core stabilisation exercise on seated postural control.

Science.gov (United States)

Lee, Jordan B; Brown, Stephen H M

2017-09-20

Core stabilisation exercises are often promoted for purposes ranging from general fitness to high-performance athletics, and the prevention and rehabilitation of back troubles. These exercises, when performed properly, may have the potential to enhance torso postural awareness and control, yet the potential for achieving immediate gains has not been completely studied. Fourteen healthy young participants performed a single bout of non-fatiguing core stabilisation exercise that consisted of repeated sets of 2 isometric exercises, the side bridge and the four-point contralateral arm-and-leg extension. Seated postural control, using an unstable balance platform on top of a force plate, was assessed before and after exercise, including multiple time points within a 20-minute follow-up period. Nine standard postural control variables were calculated at each time point, including sway displacement and velocity ranges, root mean squares and cumulative path length. Statistical analysis showed that none of the postural control variables were significantly different at any time point following completion of core stabilisation exercise. Thus, we conclude that a single bout of acute core stabilisation exercise is insufficient to immediately improve seated trunk postural control in young healthy individuals.

EMDR versus stabilisation in traumatised asylum seekers and refugees: results of a pilot study

Directory of Open Access Journals (Sweden)

Rolf J. Kleber

2011-08-01

Full Text Available Traumatised asylum seekers and refugees are clinically considered a complex population. Discussion exists on whether with this population treatment guidelines for post-traumatic stress disorder (PTSD should be followed and Trauma-Focused Cognitive-Behavioural Therapy (TF-CBT or Eye Movement Desensitisation and Reprocessing (EMDR should be applied, or whether a phased model starting with stabilisation is preferable. Some clinicians fear that trauma-focused interventions may lead to unmanageable distress or may be ineffective. While cognitive-behavioural interventions have been found to be effective with traumatised refugees, no studies concerning the efficacy of EMDR with this population have been conducted as yet.In preparation for a randomised trial comparing EMDR and stabilisation with traumatised refugees, a pilot study with 20 participants was conducted. The objective was to examine feasibility of participation in a randomised trial for this complex population and to examine acceptability and preliminary efficacy of EMDR.Participants were randomly allocated to 11 sessions of either EMDR or stabilisation. Symptoms of PTSD (SCID-I, HTQ, depression and anxiety (HSCL-25, and quality of life (WHOQOL-BREF were assessed at pre- and post-treatment and 3-month follow-up.Participation of traumatised refugees in the study was found feasible, although issues associated with complex traumatisation led to a high pre-treatment attrition and challenges in assessments. Acceptability of EMDR was found equal to that of stabilisation with a high drop-out for both conditions. No participants dropped out of the EMDR condition because of unmanageable distress. While improvement for EMDR participants was small, EMDR was found to be no less efficacious than stabilisation. Different symptom courses between the two conditions, with EMDR showing some improvement and stabilisation showing some deterioration between pre-treatment and post-treatment, justify the conduct

Simulation of feedback control system for NTM stabilisation in ASDEX Upgrade

Energy Technology Data Exchange (ETDEWEB)

Rapson, Christopher, E-mail: chris.rapson@ipp.mpg.de [Max Planck Institute for Plasma Physics, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Monaco, Francesco; Reich, Matthias; Stober, Joerg; Treutterer, Wolfgang [Max Planck Institute for Plasma Physics, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany)

2013-10-15

Highlights: ► Feedback loop to control the ECRH deposition location is modelled in Simulink. Controller optimised using simulation results. ► Apart from optimising the PID gain values, alternative architectures were trialed without risk to hardware. ► Off-normal events could be simulated, and the controller response improved. ► Optimised controller applied in experiment. Even for the low power used, partial stabilisation of NTM was observed. ► The simulation is useful outside its intended application, and for future developments of the NTM feedback control system. -- Abstract: Neoclassical Tearing Modes (NTMs) are a class of MHD instability in high beta tokamak plasmas which significantly increase radial transport, thus capping the performance of fusion plasmas. More importantly, NTMs can lead to disruptions which compromise the lifetime of structural components. Several tokamaks have demonstrated that Electron Cyclotron Resonant Heating (ECRH) can stabilise NTMs if the power deposition is aligned with the mode location. The deposition location depends on the toroidal magnetic field, flux and density profiles, and can be controlled by tilting the mirror in the ECRH launcher. Until recently, the mirror angle was set by feedforward control at ASDEX Upgrade. In order to adapt automatically to different discharge scenarios, the system at ASDEX Upgrade has been extended to steer the mirror using feedback control. The mirror must react on the current diffusion time scale, on the order of 100 ms. This is within the capabilities of the mechanical subsystem and real-time plasma diagnostics, but requires careful interfacing between these components. For example, asynchronous data transfer and non-linearities make it difficult to design an analytically optimal controller. Therefore a simulation has been used to test and tune different controller architectures. This simulation is the subject of the current contribution. Performing the optimisation process offline

Wavelength stabilisation during current pulsing of tapered laser

DEFF Research Database (Denmark)

Jensen, Ole Bjarlin

2009-01-01

The use of external feedback to stabilise the frequency of a tapered laser during current pulsing is reported. Using this technique more than 20 W of peak power in 60 ns pulses from the tapered laser is obtained and owing to the external feedback, the laser is tunable in the 778-808 nm range...

Oil-in-oil emulsions stabilised solely by solid particles.

Science.gov (United States)

Binks, Bernard P; Tyowua, Andrew T

2016-01-21

A brief review of the stabilisation of emulsions of two immiscible oils is given. We then describe the use of fumed silica particles coated with either hydrocarbon or fluorocarbon groups in acting as sole stabilisers of emulsions of various vegetable oils with linear silicone oils (PDMS) of different viscosity. Transitional phase inversion of emulsions, containing equal volumes of the two oils, from silicone-in-vegetable (S/V) to vegetable-in-silicone (V/S) occurs upon increasing the hydrophobicity of the particles. Close to inversion, emulsions are stable to coalescence and gravity-induced separation for at least one year. Increasing the viscosity of the silicone oil enables stable S/V emulsions to be prepared even with relatively hydrophilic particles. Predictions of emulsion type from calculated contact angles of a silica particle at the oil-oil interface are in agreement with experiment provided a small polar contribution to the surface energy of the oils is included. We also show that stable multiple emulsions of V/S/V can be prepared in a two-step procedure using two particle types of different hydrophobicity. At fixed particle concentration, catastrophic phase inversion of emulsions from V/S to S/V can be effected by increasing the volume fraction of vegetable oil. Finally, in the case of sunflower oil + 20 cS PDMS, the study is extended to particles other than silica which differ in chemical type, particle size and particle shape. Consistent with the above findings, we find that only sufficiently hydrophobic particles (clay, zinc oxide, silicone, calcium carbonate) can act as efficient V/S emulsion stabilisers.

Sports activity after anatomic acromioclavicular joint stabilisation with flip-button technique.

Science.gov (United States)

Porschke, Felix; Schnetzke, Marc; Aytac, Sara; Studier-Fischer, Stefan; Gruetzner, Paul Alfred; Guehring, Thorsten

2017-07-01

Sports activity after surgical AC joint stabilisation has not been comprehensively evaluated to date. The aim of this study was to determine rate, level and time to return to sports after AC joint stabilisation and to identify the influence of overhead sports on post-operative sports activity. In this retrospective case series, a total of 68 patients with a high-grade AC joint dislocation (Rockwood type V) were stabilised using a single TightRope technique. Fifty-five patients (80.9 %) with median age of 42.0 (range, 18-65) years completed questionnaires regarding sports activity before and after surgery. Clinical outcome and complications were also evaluated. Forty-three patients participated in sports regularly before injury. Their sports activity was rated according to Allain, and non-overhead and overhead sports were differentiated. At median follow-up of 24 (18-45) months, 41 of 43 patients (95.3 %) had returned to sports. 63 % returned to the same sports activity as before injury. 16.3 % needed to adapt the type of sports to reduce demanding activities. 11.6 % reduced the frequency and 32.5 % the intensity of sports. The median time to return to sports was 9.5 (3-18) months. Overhead athletes (Allain Type III and IV) had to reduce their sports activity significantly more often (11.8 vs. 53.8 %; p = 0.011) and needed more time to return to sports (9.5 vs. 4.5 months; p = 0.009). After stabilisation of AC joint dislocation, the majority of patients returned to sports after a substantial period of time. Overhead athletes, in particular, required more time and had to considerably reduce their sports activity. The findings impact therapeutic decision-making after AC joint injury and help with the prognosis and assessment of rehabilitation progress. IV.

Synthesis of yttria powders by electrospray pyrolysis

International Nuclear Information System (INIS)

Rulison, A.J.; Flagan, R.C.

1994-01-01

Electrospray atomization of high-concentration (∼400 g/L) chemical precursor solutions was applied to the synthesis of yttria powders. Conditions were found which led to high-quality powders, composed of dense, spheroidal, submicrometer, and nanocrystalline oxide particles. The precursor solutions were hydrated yttrium nitrates dissolved in n-propyl alcohol at concentrations ranging from 44.1 to 455 g/L. Electrospray atomization produced submicrometer precursor droplets which were dispersed in air and carried through an electric furnace for thermal decomposition at 500 C for several seconds residence time. X-ray powder diffraction patterns indicated the expected cubic phase. Transmission electron micrographs showed that the particle structure varied with solution composition, ranging from hollow, inflated spheres for 6-hydrated nitrates to dense spheroids for 5-hydrated nitrates. The use of 6-hydrated nitrates in the solutions appeared to form particle surfaces which were impermeable to alcohol vapor evolved during thermal decomposition, leading to hollow, inflated spheres

Electrolytic tritium enrichment: Current control using current-stabilised Kepco Type JQE modular supplies

International Nuclear Information System (INIS)

1976-01-01

This note describes the principles, design and operation of a current-stabilised power source for tritium electrolytic enrichment cells. A Kepoo Tpe JE, modular supply is current-stabilised by controlled current feedback. The accompanying control unit incorporates a temperature sensor or the cooling unit of the electrolysis cells, a line monitor to register current shut-off due to temporary power failure, a time-of-day clock, a current control potentiometer and a digital voltmeter providing current reading to an accuracy of 0.01A

Electrolytic tritium enrichment: Current control using current-stabilised Kepco Type JQE modular supplies

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-07-12

This note describes the principles, design and operation of a current-stabilised power source for tritium electrolytic enrichment cells. A Kepoo Tpe JE, modular supply is current-stabilised by controlled current feedback. The accompanying control unit incorporates a temperature sensor or the cooling unit of the electrolysis cells, a line monitor to register current shut-off due to temporary power failure, a time-of-day clock, a current control potentiometer and a digital voltmeter providing current reading to an accuracy of 0.01A.

Stabilisation de la formule des traces tordue

CERN Document Server

Moeglin, Colette

2016-01-01

Ce travail en deux volumes donne la preuve de la stabilisation de la formule des trace tordue. Stabiliser la formule des traces tordue est la méthode la plus puissante connue actuellement pour comprendre l'action naturelle du groupe des points adéliques d'un groupe réductif, tordue par un automorphisme, sur les formes automorphes de carré intégrable de ce groupe. Cette compréhension se fait en réduisant le problème, suivant les idées de Langlands, à des groupes plus petits munis d'un certain nombre de données auxiliaires; c'est ce que l'on appelle les données endoscopiques. L'analogue non tordu a été résolu par J. Arthur et dans ce livre on suit la stratégie de celui-ci. Publier ce travail sous forme de livre permet de le rendre le plus complet possible. Les auteurs ont repris la théorie de l'endoscopie tordue développée par R. Kottwitz et D. Shelstad et par J.-P. Labesse. Ils donnent tous les arguments des démonstrations même si nombre d'entre eux se trouvent déjà dans les travaux d'Ar...

Modeling and control of a gravity gradient stabilised satellite

Directory of Open Access Journals (Sweden)

Aage Skullestad

1999-01-01

Full Text Available This paper describes attitude control, i.e., 3-axes stabilisation and pointing, of a proposed Norwegian small gravity gradient stabilized satellite to be launched into low earth orbit. Generally, a gravity gradient stabilised system has limited stability and pointing capabilities, and wheels and/or magnetic coils are added in order to improve the attitude control. The best attitude accuracy is achieved using wheels, which can give accuracies down to less than one degree, but wheels increase the complexity and cost of the satellite. Magnetic coils allow cheaper satellites, and are an attractive solution to small, inexpensive satellites in low earth orbits and may provide an attitude control accuracy of a few degrees. Scientific measurements often require accurate attitude control in one or two axes only. Combining wheel and coil control may, in these cases, provide the best solutions. The simulation results are based on a linearised mathematical model of the satellite.

Comparative Assessment of Stabilised Polybutadiene Binder under Accelerated Ageing

Directory of Open Access Journals (Sweden)

Luiz Felipe Cannaval Sbegue

2016-04-01

Full Text Available Polybutadiene elastomers are versatile materials, being employed at several applications from rocket propellant binder to adhesives and sealants. The elastomers derived from hydroxyl-terminated polybutadiene are usually stabilised with antioxidants to prevent degradation. In this study, a comparative assessment among 2,2’-methylene-bis (4-methyl-6-tert-butylphenol (AO2246, 2,6-di-tert-butyl-4-methylphenol (BHT, p-phenylenediamine (pPDA, and triphenylphosphine (TPP regarding stabilisation of hydroxyl-terminated polybutadiene binder under accelerated ageing (six months at 65 °C was carried out. Evaluation of antioxidants effectiveness was examined through Oxidation Induction time, sol/gel extraction, swelling and mechanical testing, dynamic mechanical analysis, and mass variation measurement. AO2246 yielded the best performance, meanwhile BHT was poorly protective. TPP acted as prooxidant, causing a severe degradation of the binder, and pPDA was not manageable to be assessed due to the lower curing degree of the resulted polyurethane.

Low Friction in CuO-Doped Yttria-Stabilized Tetragonal Zirconia Ceramics: A Complementary Macro- and Nanotribology Study

NARCIS (Netherlands)

Tocha, E.; Pasaribu, H.R.; Schipper, Dirk J.; Schönherr, Holger; Vancso, Gyula J.

2008-01-01

The tribological behavior of CuO-doped yttria-stabilized tetragonal zirconia (3Y-TZP) ceramics in the absence of additional lubricants was characterized by macroscale pin-on-disk measurements and nanoscale atomic force microscopy (AFM) for a broad range of velocities. The previously observed low

String loop moduli stabilisation and cosmology in IIB flux compactifications

International Nuclear Information System (INIS)

Cicoli, M.

2010-01-01

We present a detailed review of the moduli stabilisation mechanism and possible cosmological implications of the LARGE Volume Scenario (LVS) that emerges naturally in the context of type IIB Calabi-Yau flux compactifications. After a quick overview of physics beyond the Standard Model, we present string theory as the most promising candidate for a consistent theory of quantum gravity. We then give a pedagogical introduction to type IIB compactifications on Calabi-Yau orientifolds where most of the moduli are stabilised by turning on background fluxes. However in order to fix the Kaehler moduli one needs to consider several corrections beyond the leading order approximations. After presenting a survey of all the existing solutions to this problem, we derive the topological conditions on an arbitrary Calabi-Yau to obtain the LVS since it requires no fine-tuning of the fluxes and provides a natural solution of the hierarchy problem. After performing a systematic study of the behaviour of string loop corrections for general type IIB compactifications, we show how they play a crucial role to achieve full Kaehler moduli stabilisation in the LVS. Before examining the possible cosmological implication of these scenarios, we present a broad overview of string cosmology. We then notice how, in the case of K3-fibrations, string loop corrections give rise naturally to an inflationary model which yields observable gravity waves. We finally study the finite-temperature behaviour of the LVS and discuss prospects for future work. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Novel Xylene-Linked Maltoside Amphiphiles (XMAs) for Membrane Protein Stabilisation

DEFF Research Database (Denmark)

Cho, Kyung Ho; Du, Yang; Scull, Nicola J

2015-01-01

Membrane proteins are key functional players in biological systems. These biomacromolecules contain both hydrophilic and hydrophobic regions and thus amphipathic molecules are necessary to extract membrane proteins from their native lipid environments and stabilise them in aqueous solutions...

Robust stabilisation of time-varying delay systems with probabilistic uncertainties

Science.gov (United States)

Jiang, Ning; Xiong, Junlin; Lam, James

2016-09-01

For robust stabilisation of time-varying delay systems, only sufficient conditions are available to date. A natural question is as follows: if the existing sufficient conditions are not satisfied, and hence no controllers can be found, what can one do to improve the stability performance of time-varying delay systems? This question is addressed in this paper when there is a probabilistic structure on the parameter uncertainty set. A randomised algorithm is proposed to design a state-feedback controller, which stabilises the system over the uncertainty domain in a probabilistic sense. The capability of the designed controller is quantified by the probability of stability of the resulting closed-loop system. The accuracy of the solution obtained from the randomised algorithm is also analysed. Finally, numerical examples are used to illustrate the effectiveness and advantages of the developed controller design approach.

The distribution and stabilisation of dissolved Fe in deep-sea hydrothermal plumes

Science.gov (United States)

Bennett, Sarah A.; Achterberg, Eric P.; Connelly, Douglas P.; Statham, Peter J.; Fones, Gary R.; German, Christopher R.

2008-06-01

We have conducted a study of hydrothermal plumes overlying the Mid-Atlantic Ridge near 5° S to investigate whether there is a significant export flux of dissolved Fe from hydrothermal venting to the oceans. Our study combined measurements of plume-height Fe concentrations from a series of 6 CTD stations together with studies of dissolved Fe speciation in a subset of those samples. At 2.5 km down plume from the nearest known vent site dissolved Fe concentrations were ˜ 20 nM. This is much higher than would be predicted from a combination of plume dilution and dissolved Fe(II) oxidation rates, but consistent with stabilisation due to the presence of organic Fe complexes and Fe colloids. Using Competitive Ligand Exchange-Cathodic Stripping Voltammetry (CLE-CSV), stabilised dissolved Fe complexes were detected within the dissolved Fe fraction on the edges of one non-buoyant hydrothermal plume with observed ligand concentrations high enough to account for stabilisation of ˜ 4% of the total Fe emitted from the 5° S vent sites. If these results were representative of all hydrothermal systems, submarine venting could provide 12-22% of the global deep-ocean dissolved Fe budget.

Strontium zirconate as silicon and aluminum scavenger in yttria stabilized zirconia

DEFF Research Database (Denmark)

Andersen, Thomas; Hansen, Karin Vels; Chorkendorff, Ib

2011-01-01

Here we report on strontium zirconate as a getter for silicon dioxide and aluminum oxide in yttria stabilized zirconia (YSZ) single crystals for cleaning purposes. YSZ single crystals were covered with strontium zirconate powder and heat treated at 1450°C in water vapor. After treatment the YSZ...... by transmission electron microscopy (TEM) the interface region between bump and YSZ single crystal bulk was examined. EDS showed a homogeneous distribution of silicon and aluminum through the cross section of a bump. The results suggest strontium zirconate as a good getter for silicon and aluminum from bulk...

Rapid, cool sintering of wet processed yttria-stabilized zirconia ceramic electrolyte thin films

OpenAIRE

Park, Jun-Sik; Kim, Dug-Joong; Chung, Wan-Ho; Lim, Yonghyun; Kim, Hak-Sung; Kim, Young-Beom

2017-01-01

Here we report a photonic annealing process for yttria-stabilized zirconia films, which are one of the most well-known solid-state electrolytes for solid oxide fuel cells (SOFCs). Precursor films were coated using a wet-chemical method with a simple metal-organic precursor solution and directly annealed at standard pressure and temperature by two cycles of xenon flash lamp irradiation. The residual organics were almost completely decomposed in the first pre-annealing step, and the fluorite cr...

Positron annihilation study of yttria-stabilized zirconia nanopowders containing Cr2O3 additive

International Nuclear Information System (INIS)

Prochazka, I; Cizek, J; Melikhova, O; Kuriplach, J; Konstantinova, T E; Danilenko, I A

2011-01-01

Yttria-stabilized zirconia compacted nanopowders, doped with trivalent chromium oxide, were studied by means of high-resolution positron lifetime and coincidence Doppler broadening techniques. The observed data suggest that positrons annihilate mainly in vacancylike defects at grain boundaries or in larger open volumes most likely located at triple points. The results also show that an addition of Cr 2 O 3 leads to a decrease in grain size.

European 'Stabilisation through Association'

DEFF Research Database (Denmark)

Rodt, Annemarie Peen

In 2012 the Nobel Committee awarded the European Union (EU) its Peace Prize. It commemorated the building and sustaining of peace between Europeans, a process in which the Nobel Committee proposed that the EU and its predecessors had played an important part. It explicitly commen-ded the Union......’s success in repeatedly reconciling a divided continent and complemented its efforts to build peace beyond its borders. But does the EU (continue to) deserve such praise? This contribution examines European peacebuilding from the early inte-gration of post-World War Two economies, through the uniting...... of Europe after the Cold War to contemporary conflict management efforts in the Western Balkans and the Eastern neighbourhood. The purpose of this endeavour is to examine whether lessons from the European experience can be observed that may facilitate future regional stabilisation processes – within...

Stabilisation of Na,K-ATPase structure by the cardiotonic steroid ouabain

International Nuclear Information System (INIS)

Miles, Andrew J.; Fedosova, Natalya U.; Hoffmann, Søren V.; Wallace, B.A.; Esmann, Mikael

2013-01-01

Highlights: •Ouabain binding to pig and shark Na,K-ATPase enhances thermal stability. •Ouabain stabilises both membrane-bound and solubilised Na,K-ATPase. •Synchrotron radiation circular dichroism is used for structure determination. •Secondary structure in general is not affected by ouabain binding. •Stabilisation is due to re-arrangement of tertiary structure. -- Abstract: Cardiotonic steroids such as ouabain bind with high affinity to the membrane-bound cation-transporting P-type Na,K-ATPase, leading to complete inhibition of the enzyme. Using synchrotron radiation circular dichroism spectroscopy we show that the enzyme-ouabain complex is less susceptible to thermal denaturation (unfolding) than the ouabain-free enzyme, and this protection is observed with Na,K-ATPase purified from pig kidney as well as from shark rectal glands. It is also shown that detergent-solubilised preparations of Na,K-ATPase are stabilised by ouabain, which could account for the successful crystallisation of Na,K-ATPase in the ouabain-bound form. The secondary structure is not significantly affected by the binding of ouabain. Ouabain appears however, to induce a reorganization of the tertiary structure towards a more compact protein structure which is less prone to unfolding; recent crystal structures of the two enzymes are consistent with this interpretation. These circular dichroism spectroscopic studies in solution therefore provide complementary information to that provided by crystallography

Stabilisation of Na,K-ATPase structure by the cardiotonic steroid ouabain

Energy Technology Data Exchange (ETDEWEB)

Miles, Andrew J. [Institute of Structural and Molecular Biology, Birkbeck College, University of London, London WC1E 7HX (United Kingdom); Fedosova, Natalya U. [Department of Biomedicine, Aarhus University, DK-8000 Aarhus (Denmark); Hoffmann, Søren V. [ISA, Department of Physics and Astronomy, Aarhus University, DK-8000 Aarhus (Denmark); Wallace, B.A. [Institute of Structural and Molecular Biology, Birkbeck College, University of London, London WC1E 7HX (United Kingdom); Esmann, Mikael, E-mail: me@biophys.au.dk [Department of Biomedicine, Aarhus University, DK-8000 Aarhus (Denmark)

2013-05-31

Highlights: •Ouabain binding to pig and shark Na,K-ATPase enhances thermal stability. •Ouabain stabilises both membrane-bound and solubilised Na,K-ATPase. •Synchrotron radiation circular dichroism is used for structure determination. •Secondary structure in general is not affected by ouabain binding. •Stabilisation is due to re-arrangement of tertiary structure. -- Abstract: Cardiotonic steroids such as ouabain bind with high affinity to the membrane-bound cation-transporting P-type Na,K-ATPase, leading to complete inhibition of the enzyme. Using synchrotron radiation circular dichroism spectroscopy we show that the enzyme-ouabain complex is less susceptible to thermal denaturation (unfolding) than the ouabain-free enzyme, and this protection is observed with Na,K-ATPase purified from pig kidney as well as from shark rectal glands. It is also shown that detergent-solubilised preparations of Na,K-ATPase are stabilised by ouabain, which could account for the successful crystallisation of Na,K-ATPase in the ouabain-bound form. The secondary structure is not significantly affected by the binding of ouabain. Ouabain appears however, to induce a reorganization of the tertiary structure towards a more compact protein structure which is less prone to unfolding; recent crystal structures of the two enzymes are consistent with this interpretation. These circular dichroism spectroscopic studies in solution therefore provide complementary information to that provided by crystallography.

Geotechnical properties of peat soil stabilised with shredded waste tyre chips

Directory of Open Access Journals (Sweden)

M.A. Rahgozar

2016-02-01

Full Text Available To accommodate major civil engineering projects in or in the vicinity of peatlands, it is essential to stabilise peat deposits. On the other hand, the accumulation of waste tyres in recent decades has caused environmental problems around the world. An effective remedy for both issues is to use scrap tyre material to stabilise problematic peat soils. This article reports an experimental investigation of the effects of adding shredded tyre chips on the stability and bearing capacity of peat soil. Peat soil samples from the Chaghakhor Wetland (Chaharmahal and Bakhtiari Province, Iran were mixed with sand at a constant dosage of 400 kg m-3 and different percentages (0 %, 5 %, 10 %, 15 % and 20 % by weight of shredded tyre chips. The unconfined compressive strength, effective cohesion, angle of internal friction and coefficient of permeability were measured for all of these mixtures. The results showed that adding shredded tyre chips significantly improved the geotechnical properties of the peat soil. The mixture with 10 % shredded tyre chips showed the highest unconfined compressive strength; the one with 15 % tyre chips exhibited the highest ductility; and adding 20 % shredded tyre chips provided the highest values for angle of internal friction, effective cohesion and coefficient of permeability. Scanning Electron Micrographs (SEM showed that the pore spaces in the stabilised peat were mostly filled with sand.

Oblique ion texturing of yttria-stabilized zirconia: The {211} structure

International Nuclear Information System (INIS)

Berdahl, Paul; Reade, Ronald P.; Liu, Jinping; Russo, Richard E.; Fritzemeier, Les; Buczek, David; Schoop, Urs

2002-01-01

Amorphous (Zr,Y)O x films were synthesized by reactive magnetron sputtering and subsequently crystallized by oblique ion bombardment. Crystalline texture nucleated by the ion beam was replicated by solid-phase epitaxial growth throughout the formerly amorphous yttria-stabilized zirconia (YSZ) film. The resulting YSZ films have (211) orientation normal to the substrate with in-plane directions (111), parallel, and (110), transverse, to the azimuth of the ion beam. We hypothesize that the texture mechanism involves ion-induced film compression and shear. The results, taken together with prior work, show that oblique ion texturing of amorphous films is a general phenomenon that can be used to fabricate substrates with more than one type of crystallographic orientation

Glass formation, properties, and structure of soda-yttria-silicate glasses

Science.gov (United States)

Angel, Paul W.; Hann, Raiford E.

1991-01-01

The glass formation region of the soda yttria silicate system was determined. The glasses within this region were measured to have a density of 2.4 to 3.1 g/cu cm, a refractive index of 1.50 to 1.60, a coefficient of thermal expansion of 7 x 10(exp -6)/C, softening temperatures between 500 and 780 C, and Vickers hardness values of 3.7 to 5.8 GPa. Aqueous chemical durability measurements were made on select glass compositions while infrared transmission spectra were used to study the glass structure and its effect on glass properties. A compositional region was identified which exhibited high thermal expansion, high softening temperatures, and good chemical durability.

Glass formation, properties and structure of soda-yttria-silica glasses

Science.gov (United States)

Angel, Paul W.; Hann, Raiford E.

1992-01-01

The glass formation region of the soda yttria silicate system was determined. The glasses within this region were measured to have a density of 2.4 to 3.1 g/cu cm, a refractive index of 1.50 to 1.60, a coefficient of thermal expansion of 7 x 10(exp -6)/C, softening temperatures between 500 and 780 C, and Vickers hardness values of 3.7 to 5.8 GPa. Aqueous chemical durability measurements were made on select glass compositions while infrared transmission spectra were used to study the glass structure and its effect on glass properties. A compositional region was identified which exhibited high thermal expansion, high softening temperatures, and good chemical durability.

IMPACT OF A USED STABILISER ON THE CALIFORNIA BEARING RATIO OF THE CLAYEY-SANDY SILT

Directory of Open Access Journals (Sweden)

Katarzyna Kamińska

2017-01-01

Full Text Available The paper aimed at the determination of the California Bearing Ratio of a stabilised and unstabilised fine-grained mineral soil. A clayey-sandy silt with the addition of 3, 6 and 10% of road stabilisers Solidex and Solidex A was used for the tests. The tests were carried out in the press Tritech 50 at the loading of 22 and 44 N. The stabilised samples were subjected to 7-days treatment, whereas unstabilised 4-days treatment. Stabilization with the applied road binders brought positive effects, there occurred a significant improvement in the mechanical properties of the clayey-sandy silt. The better binder, which significantly increased the value of the CBR ratio, was Solidex A. The use of hydraulic binders is of a great importance in road building, because their addition improves the mechanical properties of weaker mineral soils.

Dureza e resistência ao desgaste da camada de ZrN formada por nitretação a plasma sobre zircônia parcialmente estabilizada com ítria Hardness and wear resistance of the ZrN layer made by plasma nitriding of yttria partially-stabilized zirconia

Directory of Open Access Journals (Sweden)

R. Milani

2010-07-01

Full Text Available Corpos-de-prova de zircônia parcialmente estabilizada com ítria foram moldados por prensagem uniaxial, sinterizados e nitretados em plasma de micro-ondas à pressão atmosférica. A camada de ZrN sobre zircônia formou-se a uma taxa de 4 µm.min-1, podendo atingir uma espessura de 500 µm. As amostras foram caracterizadas por meio de medidas de dureza e resistência ao desgaste. A superfície nitretada apresentou dureza superior e resistência ao desgaste similar ao substrato de zircônia.Samples of yttria partially-stabilized zirconia were molded by uniaxial pressing, sintered and nitrided in an atmospheric pressure microwave plasma. This procedure leads to the formation of a ZrN layer whose growth rate and thickness reached 4 µm.min-1 and 500 µm, respectively. The samples were characterized by means of hardness and wear resistance tests. The nitrided surface exhibits superior hardness and wear resistance similar to that of the zirconia substrate.

Using Dark Field X-Ray Microscopy To Study In-Operando Yttria Stabilized Zirconia Electrolyte Supported Solid Oxide Cell

DEFF Research Database (Denmark)

Sierra, J. X.; Poulsen, H. F.; Jørgensen, P. S.

Dark Field X-Ray Microscopy is a promising technique to study the structure of materials in nanometer length scale. In combination with x-ray diffraction technique, the microstructure evolution of Yttria Stabilized Zirconia electrolyte based solid oxide cell was studied running at extreme operating...

Decentralised stabilising controllers for a class of large-scale linear ...

Indian Academy of Sciences (India)

subsystems resulting from a new aggregation-decomposition technique. The method has been illustrated through a numerical example of a large-scale linear system consisting of three subsystems each of the fourth order. Keywords. Decentralised stabilisation; large-scale linear systems; optimal feedback control; algebraic ...

Novel use of hand fracture fixation plates in the surgical stabilisation of flail chest.

LENUS (Irish Health Repository)

Dunlop, Rebecca L E

2010-01-01

Plastic surgeons specialize in working closely with other surgical colleagues to help solve clinical problems. In this case, we performed surgical stabilisation of a large flail chest fragment in conjunction with the cardiothoracic surgical team, using the mini-plating set more commonly used for hand fracture fixation. The use of this fixation system for flail chest has not previously been described, but offers advantages over other reported methods, primarily by dispensing with the need for an extensive thoracotomy incision and by providing robust stabilisation without the presence of prominent hardware.

Growth kinetics of tetragonal and monoclinic ZrO{sub 2} crystallites in 3 mol% yttria partially stabilized ZrO{sub 2} (3Y-PSZ) precursor powder

Energy Technology Data Exchange (ETDEWEB)

Kuo, Chih-Wei [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Lee, Kuen-Chan [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Yen, Feng-Lin, E-mail: flyen@kmu.edu.tw [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Shen, Yun-Hwei [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Lee, Huey-Er [Department of Dentistry, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Department of Dentistry, Kaohsiung Medical University, Chung Ho Memorial Hospital, 100 Tzyou 1st Road, Kaohsiung 807, Taiwan (China); Wen, Shaw-Bing [General Education Center, Meiho Institute of Technology, 23 Pingguang Road, Neipu, Pingtung 91202, Taiwan (China); Wang, Moo-Chin, E-mail: mcwang@kmu.edu.tw [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Stack, Margaret Mary [Department of Mechanical and Aerospace Engineering, University of Strathclyde, 75 Montrose Street, Glasgow (United Kingdom)

2014-04-01

Highlights: • The crystalline structures were composed of tetragonal and monoclinic ZrO{sub 2}. • Growth kinetics of t-ZrO{sub 2} in the 3Y-PSZ precursor powder is described as: D{sub te}{sup 2}=(4.57±0.55)t{sup 0.12±0.02}exp(-((24.79±0.38)×10{sup 3})/(RT) ). • Growth kinetics of m-ZrO{sub 2} in the 3Y-PSZ precursor powder is described as: D{sub m}{sup 2}=(4.40±1.63)t{sup 0.17±0.08}exp(-((66.47±3.97)×10{sup 3})/(RT) ). - Abstract: The growth kinetics of tetragonal and monoclinic ZrO{sub 2} crystallites in 3 mol% yttria partially stabilized ZrO{sub 2} (3Y-PSZ) precursor powder has been investigated using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) specific surface area analysis, transmission electron microscopy (TEM) and high resolution TEM (HRTEM). After calcination of the 3Y-PSZ precursor powder between 773 and 1073 K for 2 h, the crystalline structures were composed of tetragonal and monoclinic ZrO{sub 2} as the primary and secondary phases, respectively. When the 3Y-PSZ precursor powder was calcined at 773 K for 2 h, the BET specific surface area was 97.13 m{sup 2}/g, which is equivalent to a particle size of 10.30 nm. The crystallite sizes determined via XRD and BET agreed well, indicating that the powder was virtually non-agglomerated. The growth kinetics of tetragonal and monoclinic ZrO{sub 2} crystallite isothermal growth in the 3Y-PSZ precursor powder are described by: D{sub te}{sup 2}=(4.57±0.55)t{sup 0.12±0.02}exp(-((24.79±0.38)×10{sup 3})/(RT) ) and D{sub m}{sup 2}=(4.40±1.63)t{sup 0.17±0.08}exp(-((66.47±3.97)×10{sup 3})/(RT) ), respectively, for 773K≤T≤1073K. D{sub te} and D{sub m} denote the crystallite size of tetragonal and monoclinic ZrO{sub 2} at time t and temperature T, respectively.

G-fluxes and non-perturbative stabilisation of heterotic M-theory

International Nuclear Information System (INIS)

Curio, Gottfried; Krause, Axel

2002-01-01

We examine heterotic M-theory compactified on a Calabi-Yau manifold with an additional parallel M5-brane. The dominant non-perturbative effect stems from open membrane instantons connecting the M5 with the boundaries. We derive the four-dimensional low-energy supergravity potential for this situation including subleading contributions as it turns out that the leading term vanishes after minimisation. At the minimum of the potential the M5 gets stabilised at the middle of the orbifold interval while the vacuum energy is shown to be manifestly positive. Moreover, induced by the non-trivial running of the Calabi-Yau volume along the orbifold which is driven by the G-fluxes, we find that the orbifold-length and the Calabi-Yau volume modulus are stabilised at values which are related by the G-flux of the visible boundary. Finally we determine the supersymmetry-breaking scale and the gravitino mass for this open membrane vacuum

Integrated waste management as a climate change stabilisation wedge for the Maltese islands.

Science.gov (United States)

Falzon, Clyde; Fabri, Simon G; Frysinger, Steven

2013-01-01

The continuous increase in anthropogenic greenhouse gas emissions occurring since the Industrial Revolution is offering significant ecological challenges to Earth. These emissions are leading to climate changes which bring about extensive damage to communities, ecosystems and resources. The analysis in this article is focussed on the waste sector within the Maltese islands, which is the largest greenhouse gas emitter in the archipelago following the energy and transportation sectors. This work shows how integrated waste management, based on a life cycle assessment methodology, acts as an effective stabilisation wedge strategy for climate change. Ten different scenarios applicable to the Maltese municipal solid waste management sector are analysed. It is shown that the scenario that is most coherent with the stabilisation wedges strategy for the Maltese islands consists of 50% landfilling, 30% mechanical biological treatment and 20% recyclable waste export for recycling. It is calculated that 16.6 Mt less CO2-e gases would be emitted over 50 years by means of this integrated waste management stabilisation wedge when compared to the business-as-usual scenario. These scientific results provide evidence in support of policy development in Malta that is implemented through legislation, economic instruments and other applicable tools.

Electrokinetic Stabilisation Method of Soft Clay in Pure System using Electrokinetic Geosynthetic Electrode

Science.gov (United States)

Azhar, A. T. S.; Jefferson, I.; Madun, A.; Abidin, M. H. Z.; Rogers, C. D. F.

2018-04-01

Electrokinetic stabilisation (EKS) method has the ability to solve the problems of soft highly compressibility soil. This study will present the results from an experimental study of EKS on soft soils using inactive kaolinite clay, inert electrode and distilled water (DW) as a pure system mechanism before any chemical stabilisers being used in this research. Therefore, this will provide a baseline study to improve the efficiency of EKS approach. The test model was using inert electrode of Electrokinetic Geosythentic (EKG) developed at the Newcastle University to apply a constant voltage gradient of 50 V/m across a soil sample approximately 400 mm. Distilled water was used at the pore electrolyte fluid compartments supplied under zero hydraulic gradient conditions for the periods of 3, 7 and 14 days. Throughout the monitoring, physical and chemical characteristics were measured. Results from the monitoring data, physical and chemical properties of the pure system showed the development of pH gradient, the changes of electrical conductivity and chemical concentrations with regards to the distance from anode and treatment periods due to the electrochemical effects even though there was no chemical stabilisers were introduced or released from the degradation of electrodes.

Cold laser machining of nickel-yttrium stabilised zirconia cermets: Composition dependence

International Nuclear Information System (INIS)

Sola, D.; Gurauskis, J.; Pena, J.I.; Orera, V.M.

2009-01-01

Cold laser micromachining efficiency in nickel-yttrium stabilised zirconia cermets was studied as a function of cermet composition. Nickel oxide-yttrium stabilised zirconia ceramic plates obtained via tape casting technique were machined using 8-25 ns pulses of a Nd: YAG laser at the fixed wavelength of 1.064 μm and a frequency of 1 kHz. The morphology of the holes, etched volume, drill diameter, shape and depth were evaluated as a function of the processing parameters such as pulse irradiance and of the initial composition. The laser drilling mechanism was evaluated in terms of laser-material interaction parameters such as beam absorptivity, material spallation and the impact on the overall process discussed. By varying the nickel oxide content of the composite the optical absorption (-value is greatly modified and significantly affected the drilling efficiency of the green state ceramic substrates and the morphology of the holes. Higher depth values and improved drilled volume upto 0.2 mm 3 per pulse were obtained for substrates with higher optical transparency (lower optical absorption value). In addition, a laser beam self-focussing effect is observed for the compositions with less nickel oxide content. Holes with average diameter from 60 μm to 110 μm and upto 1 mm in depth were drilled with a high rate of 40 ms per hole while the final microstructure of the cermet obtained by reduction of the nickel oxide-yttrium stabilised zirconia composites remained unchanged.

Determination of standard Gibbs free energy of formation for Ca2P2O7 and Ca(PO3)2 from solid-state EMF measurements using yttria stabilised zirconia as solid electrolyte

International Nuclear Information System (INIS)

Sandstroem, Malin Hannah; Bostroem, Dan; Rosen, Erik

2006-01-01

The equilibrium reactions: 3Ca 2 P 2 O 7 (s)+6Ni(s)-bar 2Ca 3 (PO 4 ) 2 (s)+2Ni 3 P(s)+52O 2 (g) and 2Ca(PO 3 ) 2 (s)+6Ni(s)-bar Ca 2 P 2 O 7 (s)+2Ni 3 P(s)+52O 2 (g) were studied in the temperature range 890K to 1140K. The oxygen equilibrium pressures were determined using galvanic cells incorporating yttria stabilized zirconia as solid electrolyte. From the measured data and using the literature values of standard Gibbs free energy of formation for Ca 3 (PO 4 ) 2 and Ni 3 P, the following relationship of the standard Gibbs free energy of formation for Ca 2 P 2 O 7 and Ca(PO 3 ) 2 were calculated:Δ f G o (Ca 2 P 2 O 7 )+/-11/(kJ.mol -1 )=-3475.9+1.5441(T/K)-0.1051(T/K).ln(T/K)andΔ f G o (Ca(PO 3 ) 2 )+/-12/(kJ.mol -1 )=-3334.8+6.1561(T/K)-0.6950(T/K).ln(T/K)

Electron magnetic resonance investigation of chromium diffusion in yttria powders

Energy Technology Data Exchange (ETDEWEB)

Biasi, R.S. de, E-mail: rsbiasi@ime.eb.b [Secao de Engenharia Mecanica e de Materiais, Instituto Militar de Engenharia, Pr. General Tiburcio, 80, 22290-270 Rio de Janeiro, RJ (Brazil); Grillo, M.L.N., E-mail: mluciag@uerj.b [Instituto de Fisica, Universidade do Estado do Rio de Janeiro, 20550-013 Rio de Janeiro, RJ (Brazil)

2010-03-01

The electron magnetic resonance (EMR) technique was used to investigate the diffusion of chromium in yttria (Y{sub 2}O{sub 3}) powders. The EMR absorption intensity was measured for several annealing times and three different temperatures of isothermal annealing: 1273, 1323 and 1373 K. The activation temperature for diffusion, calculated from the experimental data using a theoretical model based on the Fick equation, was found to be E{sub A}=342+-5 kJ mol{sup -1}. This value is larger than the activation energy for the diffusion of chromium in rutile (TiO{sub 2}), periclase (MgO) and cobalt monoxide (CoO) and smaller than the activation energy for the diffusion of chromium in chrysoberyl (BeAl{sub 2}O{sub 4}).

Tetragonal BiFeO3 on yttria-stabilized zirconia

International Nuclear Information System (INIS)

Liu, Heng-Jui; Du, Yu-Hao; Gao, Peng; Ikuhara, Yuichi; Huang, Yen-Chin; Chen, Yi-Chun; Chen, Hsiao-Wen; Liu, Hsiang-Lin; He, Qing; Chu, Ying-Hao

2015-01-01

High structural susceptibility of multiferroic BiFeO 3 (BFO) makes it a potential replacement of current Pb-based piezoelectrics. In this study, a tetragonal phase is identified based on a combination of x-ray diffraction, scanning transmission electronic microscopy, x-ray absorption spectroscopy, and Raman spectroscopy when BFO is grown on yttria-stabilized zirconia (YSZ) substrates. To distinguish the discrepancy between this tetragonal phase and common cases of monoclinic BFO, piezoelectric force microscopy images and optical property are also performed. It shows a lower electrostatic energy of ferroelectric domains and a large reduction of band gap for BFO grown on YSZ substrate comparing to the well-known one grown on LaAlO 3 substrate. Our findings in this work can provide more insights to understand the structural diversity of multiferroic BFO system for further applications

EPR study of electron traps in x-ray-irradiated yttria-stabilized zirconia

International Nuclear Information System (INIS)

Azzoni, C.B.; Paleari, A.

1989-01-01

Single crystals of yttria-stabilized zirconia (12 mol % of Y 2 O 3 ) have been x-ray irradiated at room temperature. The electron paramagnetic resonance spectrum of the filled electron traps is analyzed in terms of a single oxygen vacancy type of defect with its symmetry axis along the left-angle 111 right-angle direction. The angular dependence of the linewidth and the asymmetry of the line shape are attributed to the disordered rearrangements of the anion sublattice surrounding the oxygen vacancy. This affects the local crystal fields and the directions of the symmetry axis of the defects

EPR study of electron traps in x-ray-irradiated yttria-stabilized zirconia

Energy Technology Data Exchange (ETDEWEB)

Azzoni, C.B.; Paleari, A. (Dipartimento di Fisica, Alessandro Volta dell' Universita di Pavia, via Bassi 6, 27100 Pavia, Italy (IT))

1989-10-01

Single crystals of yttria-stabilized zirconia (12 mol % of Y{sub 2}O{sub 3}) have been x-ray irradiated at room temperature. The electron paramagnetic resonance spectrum of the filled electron traps is analyzed in terms of a single oxygen vacancy type of defect with its symmetry axis along the {l angle}111{r angle} direction. The angular dependence of the linewidth and the asymmetry of the line shape are attributed to the disordered rearrangements of the anion sublattice surrounding the oxygen vacancy. This affects the local crystal fields and the directions of the symmetry axis of the defects.

Developments of capacitance stabilised etalon technology

Science.gov (United States)

Bond, R. A.; Foster, M.; Thwaite, C.; Thompson, C. K.; Rees, D.; Bakalski, I. V.; Pereira do Carmo, J.

2017-11-01

This paper describes a high-resolution optical filter (HRF) suitable for narrow bandwidth filtering in LIDAR applications. The filter is composed of a broadband interference filter and a narrowband Fabry-Perot etalon based on the capacitance stabilised concept. The key requirements for the HRF were a bandwidth of less than 40 pm, a tuneable range of over 6 nm and a transmission greater than 50%. These requirements combined with the need for very high out-of-band rejection (greater than 50 dB in the range 300 nm to 1200 nm) drive the design of the filter towards a combination of high transmission broadband filter and high performance tuneable, narrowband filter.

PHAST- a spectrum stabilising PC-MCA

International Nuclear Information System (INIS)

Mukhopadhyay, P.K.; Satish, P.; Shrivastava, V.D.

2001-01-01

Model PHAST, a PC-card with programmable features, incorporates a 100 MHz Wilkinson ADC with conversion gain of 8K. It also provides SCA mode MCS operation. The card caters to the needs of precision nuclear spectroscopy at low to moderate count rates. Spectrum drift may be eliminated by spectrum stabilisation. Proper dead time correction is achieved by Gedcke-Hale or pulse generator based schemes. Multiple cards may be operated together in a single PC in independent operating modes. These cards have onboard histogram memory and updating mechanism. Hence they will usually continue to acquire data in the event of a system crash. (author)

On stabilisability of 2-D MIMO shift-invariant systems

Czech Academy of Sciences Publication Activity Database

Augusta, Petr; Augustová, Petra

2013-01-01

Roč. 350, č. 10 (2013), s. 2949-2966 ISSN 0016-0032 R&D Projects: GA ČR GPP103/12/P494 Institutional support: RVO:67985556 Keywords : spatially invariant system * stabilisation * multiple-input-multiple-output system, * positive polynomial Subject RIV: BC - Control Systems Theory Impact factor: 2.260, year: 2013 http://library.utia.cas.cz/separaty/2013/TR/augusta-0398772.pdf

Kinetic Monte Carlo Simulation of Oxygen and Cation Diffusion in Yttria-Stabilized Zirconia

Science.gov (United States)

Good, Brian

2011-01-01

Yttria-stabilized zirconia (YSZ) is of interest to the aerospace community, notably for its application as a thermal barrier coating for turbine engine components. In such an application, diffusion of both oxygen ions and cations is of concern. Oxygen diffusion can lead to deterioration of a coated part, and often necessitates an environmental barrier coating. Cation diffusion in YSZ is much slower than oxygen diffusion. However, such diffusion is a mechanism by which creep takes place, potentially affecting the mechanical integrity and phase stability of the coating. In other applications, the high oxygen diffusivity of YSZ is useful, and makes the material of interest for use as a solid-state electrolyte in fuel cells. The kinetic Monte Carlo (kMC) method offers a number of advantages compared with the more widely known molecular dynamics simulation method. In particular, kMC is much more efficient for the study of processes, such as diffusion, that involve infrequent events. We describe the results of kinetic Monte Carlo computer simulations of oxygen and cation diffusion in YSZ. Using diffusive energy barriers from ab initio calculations and from the literature, we present results on the temperature dependence of oxygen and cation diffusivity, and on the dependence of the diffusivities on yttria concentration and oxygen sublattice vacancy concentration. We also present results of the effect on diffusivity of oxygen vacancies in the vicinity of the barrier cations that determine the oxygen diffusion energy barriers.

Amplitude based feedback control for NTM stabilisation at ASDEX Upgrade

Energy Technology Data Exchange (ETDEWEB)

Rapson, Christopher, E-mail: chris.rapson@ipp.mpg.de; Giannone, Louis; Maraschek, Marc; Reich, Matthias; Stober, Joerg; Treutterer, Wolfgang

2014-05-15

Highlights: • Two algorithms have been developed which use the NTM amplitude to control ECCD deposition and stabilise NTMs. • Both algorithms were tested and tuned in a simulation of the full feedback loop including an MRE. • Both algorithms have been successfully deployed in ASDEX Upgrade experiments. • Use of the NTM amplitude adds considerable robustness, which is necessary when trying to target ECCD to within 1 cm of the island location. • This is part of ongoing work to reliably and quickly stabilise NTMs in any plasma scenario. - Abstract: Neoclassical Tearing Modes (NTMs) degrade the confinement in tokamak plasmas at high beta, placing a major limitation on the projected fusion performance. Furthermore, NTMs can lead to disruptions with even more severe consequences. Therefore methods to stabilise NTMs are being developed with high priority at several research institutes worldwide. The favoured method is to deposit Electron Cyclotron Current Drive (ECCD) precisely at the mode location by controlling a movable mirror in the ECCD launcher. This method requires both the mode location and the deposition location to be known with high accuracy in real time. The required accuracy is given by half of the marginal island width, or approximately 1 cm for a m/n = 3/2 NTM at ASDEX Upgrade. Despite considerable development on a range of diagnostics, it remains challenging to provide the necessary accuracy reliably and in real time. To relax the accuracy requirements and add robustness, the feedback controller can additionally consider the effect of ECCD on the NTM amplitude directly. Then the optimal deposition location is simply where the NTM amplitude is minimised. The simplest implementation sweeps the ECCD beam across the expected NTM location. After the sweep, the beam can be returned to the optimal location and held there to stabilise the NTM. Unfortunately, waiting for a full sweep takes too long. Therefore a second method assesses the NTM growth every

Effects of the presence of heavy rare earths on the stabilization of the zirconia ceramics - Yttria; Efeito da presenca de terras raras pesadas na estabilizacao das fases de ceramicas de zirconia - itria

Energy Technology Data Exchange (ETDEWEB)

Lazar, D.R.R.; Fancio, E.; Menezes, C.A.B.; Ussui, V.; Bressiani, A.H.A.; Lima, N.B.; Paschoal, J.O.A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)], e-mail: drlazar@net.ipen.br

2000-07-01

The use of Yttria concentrates has been proposed to substitute the high purity Yttria in the zirconia stabilization. The elements terbium, dysprosium, holmium, erbium and ytterbium, classified as heavy rare earths, are the main impurities in these concentrates, due to their presence in yttrium ores. Besides that, the chemical similarities of these elements need the utilization of complex purification techniques. Considering the importance of the employed dopant on zirconia crystallization, this work shows the quantitative phases analysis of powders and ceramics of stabilized zirconia doped with 3 and 9 mol % of high purity Yttria and with a 85 wt % Yttria concentrate. This determination was performed using the Rietveld refinement of the X-ray diffraction data. The powders were synthesized by the hydroxides coprecipitation route, which includes treatments with ethanol and butanol, drying, calcination at 800 deg C for 1 hour and milling in a ball mill and in an attrition mill. The ceramics pellets were pressed uniaxially and sintered at 1550 deg C for 1 hour. The powders and sintered pellets were also characterized by X-ray fluorescence analysis, laser diffraction, gas adsorption (B.E.T.), scanning electron microscopy and determination of apparent density by the Archimedes method. The results showed the same stabilization behavior when it was employed high purity Yttria and a concentrate of this oxide. It was also observed the predominating formation of tetragonal and cubic phases when the dopant concentration is 3 and 9 mol %, respectively. (author)

The effect of environmental conditions and soil physicochemistry on phosphate stabilisation of Pb in shooting range soils.

Science.gov (United States)

Sanderson, Peter; Naidu, Ravi; Bolan, Nanthi

2016-04-01

The stabilisation of Pb in the soil by phosphate is influenced by environmental conditions and physicochemical properties of the soils to which it is applied. Stabilisation of Pb by phosphate was examined in four soils under different environmental conditions. The effect of soil moisture and temperature on stabilisation of Pb by phosphate was examined by measurement of water extractable and bioaccessible Pb, sequential fractionation and X-ray absorption spectroscopy. The addition of humic acid, ammonium nitrate and chloride was also examined for inhibition or improvement of Pb stability with phosphate treatment. The effect of moisture level varied between soils. In soil MB and DA a soil moisture level of 50% water holding capacity was sufficient to maximise stabilisation of Pb, but in soil TV and PE reduction in bioaccessible Pb was inhibited at this moisture level. Providing moisture at twice the soil water holding capacity did not enhance the effect of phosphate on Pb stabilisation. The difference of Pb stability as a result of incubating phosphate treated soils at 18 °C and 37 °C was relatively small. However wet-dry cycles decreased the effectiveness of phosphate treatment. The reduction in bioaccessible Pb obtained was between 20 and 40% with the most optimal treatment conditions. The reduction in water extractable Pb by phosphate was substantial regardless of incubation conditions and the effect of different temperature and soil moisture regimes was not significant. Selective sequential extraction showed phosphate treatment converted Pb in fraction 1 (exchangeable, acid and water soluble) to fraction 2 (reducible). There were small difference in fraction 4 (residual) Pb and fraction 1 as a result of treatment conditions. X-ray absorption spectroscopy of stabilised PE soil revealed small differences in Pb speciation under varying soil moisture and temperature treatments. The addition of humic acid and chloride produced the greatest effect on Pb speciation in

Slip casting of thoria-10 mole per cent yttria solid electrolyte

International Nuclear Information System (INIS)

Ramanathan, S.; Rao, S.V.K.

1990-01-01

One end closed thoria-yttria solid electrolyte have been fabricated by the slip casting technique. A systematic study of the influence of the process parameters on the characteristics of the final bodies has been carried out. Slips of ThO 2 -10 mole % Y 2 O 3 were prepared; their fluidity and castability were studied as a function of concentration, pH and particle size. The bodies were sintered at 2000degC and the physical properties like density and microstructure were evaluated. Slip cast bodies of bulk densities around 95% T.D. with relatively inhomogenous but predominantly fine grained structure could be obtained by optimizing the process variables. (author). 5 figs., 10 refs

Effect of agglomerate strength on sintered density for yttria powders containing agglomerates of monosize spheres

International Nuclear Information System (INIS)

Ciftcioglu, M.; Akine, M.; Burkhart, L.

1987-01-01

The effect of agglomerate strength on sintered density was determined for several yttria powders made by intentionally agglomerating 0.1-μm, monodisperse yttriuim hydrocarbonate precursor spheres and calcining separate portions of the precursor at different temperatures to vary the strength of the intraaglomeate bonds. In this way, the effects of differences in particle morphology and other characteristics among the powders were minimized and the effect of agglomerate strength could be seen more clearly

Direct and indirect stabilisation mechanisms in multiple electron capture

Energy Technology Data Exchange (ETDEWEB)

Roncin, P. [Paris-11 Univ., 91 - Orsay (France). Lab. de Collisions Atomiques et Moleculaires; Barat, M. [Paris-11 Univ., 91 - Orsay (France). Lab. de Collisions Atomiques et Moleculaires; Gaboriaud, M.N. [Paris-11 Univ., 91 -Orsay (France). Lab. de Collisions Atomiques et Moleculaires; Szilagyi, Z.S. [Paris-11 Univ., 91 - Orsay (France). Lab. de Collisions Atomiques et Moleculaires; Kazansky, A.K. [Paris-11 Univ., 91 - Orsay (France). Lab. de Collisions Atomiques et Moleculaires

1995-05-01

During the last years both experimental and theoretical works have focused on the problem of the stabilisation of two excited electrons on the projectile. In this contribution we would like to give experimental examples of the two suggested mechanisms and their extension to multiple electron capture. Our data are discussed together with those obtained with other experimental techniques and with theoretical predictions. (orig./WL).

Sintering and annealing effects on undoped yttria transparent ceramics

Energy Technology Data Exchange (ETDEWEB)

Letue, Laetitia; Petit, Johan, E-mail: johan.petit@onera.fr; Ritti, Marie-Hélène; Lalanne, Sylvie; Landais, Stéphane

2017-06-15

Transparent yttrium oxide (Y{sub 2}O{sub 3}) ceramics were processed by several densifications steps without any doping species. The green bodies were obtained by the aqueous way and sintered at high temperature under vacuum and then under high pressure. We studied the effects of different sintering cycles and air annealing at different steps of the process on the density and the grain growth. We also focused on the reaction between yttria ceramics and BN-coated graphite crucible which occurs during HIP. We noted that a low heating rate and two annealing steps are necessary to improve our samples’ transparency. - Highlights: • The quality of transparent ceramics is compared with the tested process parameters. • Air annealing is critical when using a carbon environment in the process. • Intra-granular pores, and so the final transparency, are directly linked to the sintering heating rates.

Anisotropic ionic conductivity observed in superplastically deformed yttria-stabilized zirconia/alumina composite

International Nuclear Information System (INIS)

Drennan, J.; Swain, M.V.; Badwal, S.P.S.

1989-01-01

Ionic conductivity measurements on a yttria-stabilized tetragonal zirconia polycrystal/alumina composite subjected to superplastic deformation demonstrate anisotropic character. Parallel to the pressing direction, the grain-boundary resistance to oxygen ion mobility is 25% to 30% higher than that measured perpendicular to the pressing direction. The same directional dependency on the volume conductivity is observed but is less pronounced, showing approximately a 9% difference. Microstructural evidence reveals an agglomeration and elongation of alumina particles perpendicular to the pressing direction, and it is suggested that this phenomenon restricts the passage of ions parallel to the compression direction, giving rise to the anisotropic nature of the conductivity measurements

Metallurgical aspects of the weldability of Cr-Mo stabilised ferritic steels

International Nuclear Information System (INIS)

Colombe, Gerard; Petrequin, Pierre; Donati, J.R.; Zacharie, C.

1977-01-01

Results of tests performed to compare the tendency of 2.25 Cr-Mo and 9 Cr-2 Mo steels stabilised with niobium and niobium + vanadium, to different cracking phenomena susceptible to occur during welding, stress-relieving and service in the conditions of fast breeder reactors are presented

Stabilisation of ZrO/sub 2/ with rare-earth oxides with atomic numbers from 58 to 71

Energy Technology Data Exchange (ETDEWEB)

Tcheivili, L; Passarino de Marques, M N [Instituto Nacional de Tecnologia Industrial, Buenos Aires (Argentina)

1978-01-01

In the present work, the stabilisation of ZrO/sub 2/ with 14 rare earths (58 to 71) was investigated. The aim was to carry out the experiments at a temperature of 1550/sup 0/C, at which many oxides do not exist in the cubic form and the others, such as PrO/sub 2/ and Lu/sub 2/O/sub 3/, have not yet been studied. All the experiments of the series were carried out under constant conditions, in order to determine if there was any difference in principle between them. All the oxides stabilise ZrO/sub 2/, but those with the lower atomic numbers (58, 59, 60) show some deviation. The minimum and maximum mol% limits were ascertained, between which ZrO/sub 2/ is fully stabilised, and the phases are given which occur with the various mol% proportions. In conclusion, an experiment was carried out with all oxides having di- tri- and quadri-valent cations, which belong to the cubic system. In view of their difference in ionic radius to the Zr/sup 4 +/ ion, the conclusion can be drawn that all oxides which can stabilise ZrO/sub 2/ have larger cation radii than that of the Zr/sup 4 +/ ion.

Grinding media of Zr O2-Y2 O3

International Nuclear Information System (INIS)

Ussui, V.; Leitao, F.; Paschoal, J.O.A.

1994-01-01

This paper describes an experiment carried out to test Yttria 3 mol% stabilized zirconia as a grinding media. The Powders were produced in experimental operations of a wet chemical coprecipitation process at the Zirconium Pilot Plant in IPEN. The stabilised zirconia powders obtained were cold pressed in to cylindrical shapes and sintered at 1500 0 C for hour. The ceramics produced presented good wear resistance and were found to be efficient as zirconia powders grinding media. (author)

Stabilisation of amorphous furosemide increases the oral drug bioavailability in rats

DEFF Research Database (Denmark)

Nielsen, Line Hagner; Rades, Thomas; Müllertz, Anette

2015-01-01

A glass solution of the amorphous sodium salt of furosemide (ASSF) and polyvinylpyrrolidone (PVP) (80: 20 w/w%) was prepared by spray drying. It was investigated if PVP was able to stabilise ASSF during storage and dissolution and whether this influenced the in vivo performance of the glass...

An analysis of stabilisation for head and neck image guided IMRT

International Nuclear Information System (INIS)

Middleton, Mark; Nguyen, Huong; Plank, Ashley; Jones, Mark; Shannon, Debbie; Sisson, Toni

2014-01-01

Aims: Daily IGRT using kV imaging has allowed an enhanced field of view for head and neck IMRT patients. This has allowed the treating radiation therapists to note set-up error beyond traditional spatial or translational and include angular error. This study compares two stabilisation methods for head and neck IGRT and compares spatial and angular error between them. Methods and materials: 9 patients were assessed using a CIVCO S-board and generic Silverman head rest and another 9 patients were assessed using a CIVCO S-board with a CIVCO S-type vac-fix bag. Daily IGRT was undertaken and pre-intervention set-up error collected. This was inclusive of error in the lateral, longitudinal and vertical plans and angular discrepancy between cervical spine 1 and cervical spine 7. Results: The vac-fix solution provided a significant reduction in the systematic yaw position (anterior–posterior) (p = 0.04). It also reduced the mean resultant systematic angular error significantly (p = 0.01). The lateral systematic spatial error was decreased significantly by the vac-fix (p = 0.03) whilst the longitudinal and vertical systematic errors were not. The differences in random error between the two stabilisation solutions were not significant. Conclusion: kV IGRT has allowed treating radiation therapists to note angular error in the head and neck region. This can be difficult to deal with using only IGRT. Stabilisation solutions in the head and neck region must be able to manage both spatial and angular set-up error. The vac-fix solution has improved the management of angular error for head and neck IMRT patients

Study on nano-structured hydroxyapatite/zirconia stabilized yttria on healing of articular cartilage defect in rabbit

Directory of Open Access Journals (Sweden)

Amir Sotoudeh

2013-05-01

Full Text Available PURPOSE: Articular Cartilage has limited potential for self-repair and tissue engineering approaches attempt to repair articular cartilage by scaffolds. We hypothesized that the combined hydroxyapatite and zirconia stabilized yttria would enhance the quality of cartilage healing. METHODS: In ten New Zealand white rabbits bilateral full-thickness osteochondral defect, 4 mm in diameter and 3 mm depth, was created on the articular cartilage of the patellar groove of the distal femur. In group I the scaffold was implanted into the right stifle and the same defect was created in the left stifle without any transplant (group II. Specimens were harvested at 12 weeks after implantation, examined histologically for morphologic features, and stained immunohistochemically for type-II collagen. RESULTS: In group I the defect was filled with a white translucent cartilage tissue In contrast, the defects in the group II remained almost empty. In the group I, the defects were mostly filled with hyaline-like cartilage evidenced but defects in group II were filled with fibrous tissue with surface irregularities. Positive immunohistochemical staining of type-II collagen was observed in group I and it was absent in the control group. CONCLUSION: The hydroxyapatite/yttria stabilized zirconia scaffold would be an effective scaffold for cartilage tissue engineering.

Evaluation of the effect of heavy rare earth elements on the microstructure and mechanical and electrical properties of zirconia - Yttria ceramics

International Nuclear Information System (INIS)

Lazar, Dolores Ribeiro Ricci

2002-01-01

The use of Yttria concentrates for synthesis and processing of zirconia based ceramics, applied as structural and solid electrolyte materials, was investigated in this work. Terbium, dysprosium, holmium, erbium and ytterbium are chemical elements, classified as heavy rare earths, that can be found in those concentrates due to their association with yttrium ores. The ceramic characteristics were compared to zirconia - Yttria and zirconia - Yttria - rare earth oxide systems. The dopant content was 3 and 9 mol%. The raw materials were prepared by the coprecipitation route using solutions from the chemical processing of zircon and monazite ores and obtained by dissolution of high purity rare earth oxides. In the first part of this work, calcination, milling and ceramic processing were studied to produce ceramics with densities up to 95% TD. Samples were prepared in optimized conditions for the evaluation of the effect of each heavy rare earth element. Powders were characterized by chemical analysis. X-ray diffraction, scanning and transmission electron microscopy, gas adsorption (BET) and laser diffraction for the determination of the agglomerate size distributions. Green pellets were characterized by mercury porosimetry and the sintering kinetic was studied by dilatometry. The characterization of the as-sintered pellets was performed by the apparent density measurement (Archimedes method). X-ray diffraction, microstructure analysis by scanning and transmission electron microscopy, Vickers indentation tests for hardness and fracture toughness determination, dynamic mechanical analysis for the elastic modulus measurement, and impedance spectroscopy for electrical resistivity measurement. It was observed that the presence of heavy rare earths in a concentrate containing 85 wt% of Yttria has no significant influence on the properties of zirconia based ceramics. TZP ceramics, containing 3 mol% of dopants, have grain size smaller than 0.4μm, and Vickers hardness and

Tetragonal BiFeO{sub 3} on yttria-stabilized zirconia

Energy Technology Data Exchange (ETDEWEB)

Liu, Heng-Jui [Department of Materials Science Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Department of Physics, National Taiwan Normal University, Taipei 11677, Taiwan (China); Du, Yu-Hao [Department of Materials Science Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Gao, Peng; Ikuhara, Yuichi [Institute of Engineering Innovation, The University of Tokyo, Tokyo 113-8656 (Japan); Huang, Yen-Chin; Chen, Yi-Chun [Department of Physics, National Cheng Kung University, Tainan 70101, Taiwan (China); Chen, Hsiao-Wen; Liu, Hsiang-Lin [Department of Physics, National Taiwan Normal University, Taipei 11677, Taiwan (China); He, Qing [Department of Physics, Durham University, Durham DH1 3LE (United Kingdom); Chu, Ying-Hao, E-mail: yhc@nctu.edu.tw [Department of Materials Science Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China)

2015-11-01

High structural susceptibility of multiferroic BiFeO{sub 3} (BFO) makes it a potential replacement of current Pb-based piezoelectrics. In this study, a tetragonal phase is identified based on a combination of x-ray diffraction, scanning transmission electronic microscopy, x-ray absorption spectroscopy, and Raman spectroscopy when BFO is grown on yttria-stabilized zirconia (YSZ) substrates. To distinguish the discrepancy between this tetragonal phase and common cases of monoclinic BFO, piezoelectric force microscopy images and optical property are also performed. It shows a lower electrostatic energy of ferroelectric domains and a large reduction of band gap for BFO grown on YSZ substrate comparing to the well-known one grown on LaAlO{sub 3} substrate. Our findings in this work can provide more insights to understand the structural diversity of multiferroic BFO system for further applications.

Study of the electronics architecture for the mechanical stabilisation of the quadrupoles of the CLIC linear accelerator

CERN Document Server

Artoos, K; Fernandez Carmona, P; Guinchard, M; Hauviller, C; Janssens, S; Kuzmin, A; Slaathaug, A

2010-01-01

To reach a sufficient luminosity, the transverse beam sizes and emittances in future linear particle accelerators should be reduced to the nanometer level. Mechanical stabilisation of the quadrupole magnets is of the utmost importance for this. The piezo actuators used for this purpose can also be used to make fast incremental orientation adjustments with a nanometer resolution. The main requirements for the CLIC stabilisation electronics is a robust, low noise, low delay, high accuracy and resolution, low band and radiation resistant feedback control loop. Due to the high number of controllers (about 4000) a cost optimization should also be made. Different architectures are evaluated for a magnet stabilisation prototype, including the sensors type and configuration, partition between software and hardware for control algorithms, and optimization of the ADC/DAC converters. The controllers will be distributed along the 50 km long accelerator and a communication bus should allow external control. Furthermore, o...

Modelling, characterisation and uncertainties of stabilised pseudoelastic shape memory alloy helical springs

DEFF Research Database (Denmark)

Enemark, Søren; Santos, Ilmar; Savi, M. A.

2016-01-01

The thermo-mechanical behaviour of pseudoelastic shape memory alloy helical springs is of concern discussing stabilised and cyclic responses. Constitutive description of the shape memory alloy is based on the framework developed by Lagoudas and co-workers incorporating two modifications related t...

Positron annihilation studies of zirconia doped with metal cations of different valence

Science.gov (United States)

Prochazka, I.; Cizek, J.; Melikhova, O.; Konstantinova, T. E.; Danilenko, I. A.; Yashchishyn, I. A.; Anwand, W.; Brauer, G.

2013-06-01

New results obtained by applying positron annihilation spectroscopy to the investigation of zirconia-based nanomaterials doped with metal cations of different valence are reported. The slow-positron implantation spectroscopy combined with Doppler broadening measurements was employed to study the sintering of pressure-compacted nanopowders of tetragonal yttria-stabilised zirconia (t-YSZ) and t-YSZ with chromia additive. Positronium (Ps) formation in t-YSZ was proven by detecting 3γ-annihilations of ortho-Ps and was found to gradually decrease with increasing sintering temperature. A subsurface layer with enhanced 3γ-annihilations, compared to the deeper regions, could be identified. Addition of chromia was found to inhibit Ps formation. In addition, first results of positron lifetime measurements on nanopowders of zirconia phase-stabilised with MgO and CeO2 are presented.

Hydrogen oxidation mechanisms on Ni/yttria stabilized zirconia anodes: Separation of reaction pathways by geometry variation of pattern electrodes

Science.gov (United States)

Doppler, M. C.; Fleig, J.; Bram, M.; Opitz, A. K.

2018-03-01

Nickel/yttria stabilized zirconia (YSZ) electrodes are affecting the overall performance of solid oxide fuel cells (SOFCs) in general and strongly contribute to the cell resistance in case of novel metal supported SOFCs in particular. The electrochemical fuel conversion mechanisms in these electrodes are, however, still only partly understood. In this study, micro-structured Ni thin film electrodes on YSZ with 15 different geometries are utilized to investigate reaction pathways for the hydrogen electro-oxidation at Ni/YSZ anodes. From electrodes with constant area but varying triple phase boundary (TPB) length a contribution to the electro-catalytic activity is found that does not depend on the TPB length. This additional activity could clearly be attributed to a yet unknown reaction pathway scaling with the electrode area. It is shown that this area related pathway has significantly different electrochemical behavior compared to the TPB pathway regarding its thermal activation, sulfur poisoning behavior, and H2/H2O partial pressure dependence. Moreover, possible reaction mechanisms of this reaction pathway are discussed, identifying either a pathway based on hydrogen diffusion through Ni with water release at the TPB or a path with oxygen diffusion through Ni to be a very likely explanation for the experimental results.

Gel combustion synthesis of yttria stabilized zirconia

International Nuclear Information System (INIS)

Vijay, Soja K.; Chandramouli, V.; Anthonysamy, S.

2013-01-01

Nano - crystalline 8 mol% yttria stabilized zirconia (YSZ) powders were synthesized by gel combustion technique employing both microwave heating as well as conventional heating method. Three different fuels - citric acid, urea and glycine were used for the synthesis with fuel to oxidant ratio as 1:1. The effect of fuel on the crystal structure, particle size, specific surface area, morphology and sintering density was studied. X-ray powder diffraction (XRD), BET gas adsorption technique, dynamic light scattering, transmission and scanning electron microscopy (TEM and SEM) and micro-Raman spectroscopy were used to characterize the powders. The results obtained for powders obtained using both methods - microwave assisted and hotplate - were compared. The specific surface area of powders in all cases are comparable except in the case of urea as fuel where microwave assisted synthesis yielded powders with lower surface area. The particle size distribution of all samples obtained using microwave method was unimodal, whereas the particle size distribution of samples prepared using hot plate method using urea fuel showed bimodal distribution. The compacts obtained using powders with citric acid and glycine as fuel showed more than 94% theoretical density, whereas the samples obtained using urea showed density below 90% of theoretical density. (author)

Stabiliser Fault Emergency Control using Reconfiguration to Preserve Power System Stability

DEFF Research Database (Denmark)

Pedersen, Andreas Søndergaard; Richter, Jan H.; Tabatabaeipour, Mojtaba

2014-01-01

Stabiliser faults in multi-machine power systems are examined in this paper where fault-masking and system reconguration of the nonlinear system is obtained using a virtual actuator approach. Phasor Measurement Units, which can be integrated in wide-area transmission grids to improve the performa...

Feedback stabilisation of pool-boiling systems : for application in thermal management schemes

NARCIS (Netherlands)

Gils, van R.W.

2012-01-01

The research scope of this thesis is the stabilisation of unstable states in a pool-boiling system. Thereto, a compact mathematical model is employed. Pool-boiling systems serve as physical model for practical applications of boiling heat transfer in industry. Boiling has advantages over

Surface modification of yttria stabilized zirconia via polydopamine inspired coating for hydroxyapatite biomineralization

Energy Technology Data Exchange (ETDEWEB)

Zain, Norhidayu Muhamad [Medical Devices and Technology Group, Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Hussain, Rafaqat [Ibnu Sina Institute for Fundamental Science Studies, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Kadir, Mohammed Rafiq Abdul, E-mail: rafiq@biomedical.utm.my [Medical Devices and Technology Group, Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia)

2014-12-15

Highlights: • Synthesis of functionalized yttria stabilized zirconia using polydopamine. • Improved hydrophilicity of the grafted samples with low contact angle of 44.0 ± 2.3. • Apatite layer with Ca/P ratio of 1.78 formed on the surface of the grafted samples. • Atomic percentage of Ca 2p increased by 2-fold at coating temperature of 37 °C. - Abstract: Yttria stabilized zirconia (YSZ) has been widely used as biomedical implant due to its high strength and enhanced toughening characteristics. However, YSZ is a bioinert material which constrains the formation of chemical bonds with bone tissue following implantation. Inspired by the property of mussels, the surface of YSZ ceramics was functionalized by quinone-rich polydopamine to facilitate the biomineralization of hydroxyapatite. YSZ discs were first immersed in 2 mg/mL of stirred or unstirred dopamine solution at either 25 or 37 °C. The samples were then incubated in 1.5 simulated body fluid (SBF) for 7d. The effect of coating temperature for stirred and unstirred dopamine solutions during substrate grafting was investigated on the basis of chemical compositions, wettability and biomineralization of hydroxyapatite on the YSZ functionalized surface. The results revealed that the YSZ substrate grafted at 37 °C in stirred solution of dopamine possessed significantly improved hydrophilicity (water contact angle of 44.0 ± 2.3) and apatite-mineralization ability (apatite ratio of 1.78). In summary, the coating temperature and stirring condition during grafting procedure affected the chemical compositions of the films and thus influenced the formation of apatite layer on the substrate during the biomineralization process.

Surface modification of yttria stabilized zirconia via polydopamine inspired coating for hydroxyapatite biomineralization

International Nuclear Information System (INIS)

Zain, Norhidayu Muhamad; Hussain, Rafaqat; Kadir, Mohammed Rafiq Abdul

2014-01-01

Highlights: • Synthesis of functionalized yttria stabilized zirconia using polydopamine. • Improved hydrophilicity of the grafted samples with low contact angle of 44.0 ± 2.3. • Apatite layer with Ca/P ratio of 1.78 formed on the surface of the grafted samples. • Atomic percentage of Ca 2p increased by 2-fold at coating temperature of 37 °C. - Abstract: Yttria stabilized zirconia (YSZ) has been widely used as biomedical implant due to its high strength and enhanced toughening characteristics. However, YSZ is a bioinert material which constrains the formation of chemical bonds with bone tissue following implantation. Inspired by the property of mussels, the surface of YSZ ceramics was functionalized by quinone-rich polydopamine to facilitate the biomineralization of hydroxyapatite. YSZ discs were first immersed in 2 mg/mL of stirred or unstirred dopamine solution at either 25 or 37 °C. The samples were then incubated in 1.5 simulated body fluid (SBF) for 7d. The effect of coating temperature for stirred and unstirred dopamine solutions during substrate grafting was investigated on the basis of chemical compositions, wettability and biomineralization of hydroxyapatite on the YSZ functionalized surface. The results revealed that the YSZ substrate grafted at 37 °C in stirred solution of dopamine possessed significantly improved hydrophilicity (water contact angle of 44.0 ± 2.3) and apatite-mineralization ability (apatite ratio of 1.78). In summary, the coating temperature and stirring condition during grafting procedure affected the chemical compositions of the films and thus influenced the formation of apatite layer on the substrate during the biomineralization process

Biomechanical Evaluation of the MACSTL Internal Fixator for Thoracic Spinal Stabilisation

Directory of Open Access Journals (Sweden)

R. Veselý

2008-01-01

Full Text Available Unstable fractures of the thoracic spine in humans represent a serious social and economic issue. They may lead to persistent consequences and chronic disease. The anatomical and biomechanical characteristics of the thoracic spine are different from all the other spinal parts due to its higher mobility. The vertebrae of the chest area are less mobile, conferring a higher degree of rigidity to the spine. To destabilize this relatively rigid system, a considerable force is necessary. The treatment of unstable spinal fractures is solely surgical. The decompression of the spinal canal with reposition and stabilisation of the fracture is indicated urgently. This intervention is performed mostly from the posterior approach in the first phase. However, the anterior spinal column is the structure responsible for the stability of the spine. Therefore, the recent advances in spine surgery focus on this area of expertise. For this reason, we carried out a bio-mechanical study aimed at assessing the effectiveness of two surgical tactics used. The study consisted of comparative experiments performed by computer-aided device on segments of pig cadavers (n = 5. The experiment involved a comparison of segments of the thoracic spine under the following conditions: an anatomically intact segment, a spine segment with an artificially created anterior instability, and a segment with an applied internal fixator. The experiment compared the mechanical characteristics of these segments. The experiment has demonstrated that after application of the internal fixator used for stabilisation of the injured anterior spinal column at defined pre-loading of 200 N, the stability of damaged spinal segment in torsion increased twofold. It was also verified that sufficient stability can be ensured using the Modular Anterior Construct System (MACSTL implant for ventral stabilisation of thoracic spine unstable injuries. Endoscopic application of this implant represents an

The Potential Of The Soil For Stabilisation Of Organic Carbon In Soil Aggregates

Directory of Open Access Journals (Sweden)

Tobiašová Erika

2015-06-01

Full Text Available Carbon stabilisation in soil is the result of interaction between the chemical and physical mechanisms of protection and the dominance of the mechanism depends not only on the long-term constant characteristics of soil but also on the properties, which can be partly influenced by human activities. In this study, the potential of the soil for stabilisation of carbon (Ps in different soil types depending on soil properties was compared. Experiment included six soils (Eutric Fluvisol, Mollic Fluvisol, Haplic Chernozem, Haplic Luvisol, Eutric Cambisol, and Rendzic Leptosol of different land uses (forest, meadow, urban, and agro-ecosystem in Slovakia. Ps was determined with dependence on the ratio of labile and stable fractions of carbon in the soil macro-aggregates. Ps was in an exponential dependence (r = 0.942; P < 0.01 with production potential of the soil, and the fractions of dry-sieved aggregates larger than 3 mm play an important role in the first stages of the carbon stabilisation. The suitable parameter, which reflects the changes in carbon stability in the soil is the ratio of the labile carbon and non-labile carbon in the soil macro-aggregates (L/NL. Lower values of L/NL that indicate a higher stability of carbon were determined at a higher pH, at the higher content of carbonates and exchangeable basic cations, and at a higherportion of humic acids free and bound with mobile sesquioxides R2O3.

Characterization of amorphous yttria layers deposited by aqueous solutions of Y-chelate alkoxides complex

Science.gov (United States)

Kim, Young-Soon; Lee, Yu-Ri; Kim, Byeong-Joo; Lee, Jae-Hun; Moon, Seung-Hyun; Lee, Hunju

2015-01-01

Crack-free amorphous yttria layers were deposited by dip coating in solutions of different Y-chelate alkoxides complex. Three Y-chelate solutions of different concentrations were prepared using yttrium acetate tetrahydrate, yttrium stearic acid as Y source materials. PEG, diethanolamine were used as chelating agents, while ethanol, methanol and tetradecane were used as solvent. Three different combinations of chelating and solvents were used to prepare solutions for Y2O3 dip coating on SUS, electropolished and non-electropolished Hastelloy C-276 substrates. The thickness of the films was varied by changing the number of dipping cycles. At an optimized condition, the substrate surface roughness (rms) value was reduced from ∼50 nm to ∼1 nm over a 10 × 10 μm2 area. After Y2O3 deposition, MgO was deposited using ion-beam assisted deposition (IBAD), then LaMnO3 (LMO) was deposited using sputtering and GdBCO was deposited using reactive co-evaporation by deposition and reaction (RCE-DR). Detailed X-ray study indicates that LMO/MgO/Y2O3 and GdBCO/LMO/MgO/Y2O3 stack films have good out-of-plane and in-plane textures with strong c-axis alignment. The critical current (Ic) of GdBCO/LMO/MgO/Y2O3 multilayer structure varied from 190 to 420 A/cm with different solutions, when measured at 77 K. These results demonstrated that amorphous yttria can be easily deposited by dip coating using Y-chelates complex as a diffusion barrier and nucleation layer.

Private sector and stabilisation in Afghanistan

DEFF Research Database (Denmark)

Magaard, Tina

I briefet opsummerer Tina Magaard de vigtigste konklusioner fra konferencen ”Private sector and stabilisation in Afghanistan – a neglected match?”, som blandt andet gav indsigt i udfordringerne og mulighederne for den private sektor i Afghanistan. Ved at kombinere perspektiver fra strategiske...... studier med forretnings- og udviklingsstudier tilbød konferencen en dybere indsigt i udfordringerne og mulighederne for den private sektor i Afghanistan. Samtidig blev der åbnet en række nye perspektiver for interaktionen mellem den private sektor og stabiliseringsoperationer i en post-krigskontekst som...... Afghanistan. Selvom udgangspunktet var Afghanistan, er konferencens konklusioner i høj grad relevante for andre konflikt/post-konfliktområder. Konferencen var organiseret i et samarbejde mellem Centre for Business and Development Studies (Copenhagen Business School), Public-Private Platform (Copenhagen...

Metastable SUSY Breaking, de Sitter Moduli Stabilisation and Kähler Moduli Inflation

CERN Document Server

Krippendorf, Sven

2009-01-01

We study the influence of anomalous U(1) symmetries and their associated D-terms on the vacuum structure of global field theories once they are coupled to N=1 supergravity and in the context of string compactifications with moduli stabilisation. In particular, we focus on a IIB string motivated construction of the ISS scenario and examine the influence of one additional U(1) symmetry on the vacuum structure. We point out that in the simplest one-Kahler modulus compactification, the original ISS vacuum gets generically destabilised by a runaway behaviour of the potential in the modulus direction. In more general compactifications with several Kahler moduli, we find a novel realisation of the LARGE volume scenario with D-term uplifting to de Sitter space and both D-term and F-term supersymmetry breaking. The structure of soft supersymmetry breaking terms is determined in the preferred scenario where the standard model cycle is not stabilised non-perturbatively and found to be flavour universal. Our scenario als...

Design of a wind turbine pitch angle controller for power system stabilisation

DEFF Research Database (Denmark)

Jauch, Clemens; Islam, S.M.; Sørensen, Poul Ejnar

2007-01-01

The design of a PID pitch angle controller for a fixed speed active-stall wind turbine, using the root locus method is described in this paper. The purpose of this controller is to enable an active-stall wind turbine to perform power system stabilisation. For the purpose of controller design......, the transfer function of the wind turbine is derived from the wind turbine's step response. The performance of this controller is tested by simulation, where the wind turbine model with its pitch angle controller is connected to a power system model. The power system model employed here is a realistic model...... of the North European power system. A short circuit fault on a busbar close to the wind turbine generator is simulated, and the dynamic responses of the system with and without the power system stabilisation of the wind turbines are presented. Simulations show that in most operating points the pitch controller...

Effects of heat on physicochemical properties of whey protein-stabilised emulsions

NARCIS (Netherlands)

Sliwinski, E.L.; Zoet, F.D.; Boekel, van M.A.J.S.; Wouters, J.T.M.; Roubos-van den Hil, P.J.

2003-01-01

The effect of heating has been studied for whey protein-stabilised oil-in-water emulsions (25.0% (w/w) soybean oil, 3.0% (w/w) whey protein isolate, pH 7.0). These emulsions were heated between 55 and 95 degreesC as a function of time and the effect on particle size distribution, adsorbed protein

Cysteine-stabilised peptide extract of Morinda lucida (Benth) leaf exhibits antimalarial activity and augments antioxidant defense system in P. berghei-infected mice.

Science.gov (United States)

Adebayo, Joseph O; Adewole, Kayode E; Krettli, Antoniana U

2017-07-31

Cysteine-stabilised peptides (CSP) are majorly explored for their bioactivities with applications in medicine and agriculture. Morinda lucida leaf is used indigenously for the treatment of malaria; it also contains CSP but the role of CSP in the antimalarial activity of the leaf has not been evaluated. This study was therefore performed to evaluate the antimalarial activity of partially purified cysteine-stabilised peptide extract (PPCPE) of Morinda lucida leaf and its possible augmentation of the antioxidant systems of liver and erythrocytes in murine malaria. PPCPE was prepared from Morinda lucida leaf. The activity of PPCPE was evaluated in vitro against Plasmodium falciparum W2 and its cytotoxicity against a BGM kidney cell line. PPCPE was also evaluated for its antimalarial activity and its effects on selected liver and erythrocyte antioxidant parameters in P. berghei NK65-infected mice. PPCPE was not active against P. falciparum W2 (IC 50 : >50µg/ml) neither was it cytotoxic (MLD 50 : >1000µg/ml). However, PPCPE was active against P. berghei NK65 in vivo, causing 51.52% reduction in parasitaemia at 31.25mg/Kg body weight on day 4 post-inoculation. PPCPE significantly reduced (P activities of glutathione peroxidase, glutathione reductase, superoxide dismutase and catalase in a dose-dependent manner, which was significant (P antimalarial effect and that PPCPE may augment the antioxidant defense system to alleviate the reactive oxygen species-mediated complications of malaria. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Re-use of stabilised flue gas ashes from solid waste incineration in cement-treated base layers for pavements

DEFF Research Database (Denmark)

Cai, Zuansi; Jensen, Dorthe Lærke; Christensen, Thomas Højlund

2003-01-01

Fly ash from coal-burning power plants has been used extensively as a pozzolan and fine filter in concrete for many years. Laboratory experiments were performed investigating the effect of substituting the coal-based fly ash with chemically stabilised flue gas ashes (FGA) from waste incineration...... more than 5 MPa after 7 days. The tank leaching tests revealed that leaching of heavy metals was not significantly affected by the use of chemically stabilised flue gas ashes from waste incineration. Assuming that diffusion controls the leaching process it was calculated that less than 1% of the metals...... would teach during a 100-year period from a 0.5 m thick concrete stab exposed to water on one side. Leaching of the common ions Ca, Cl, Na and SO4 was increased 3-20 times from the specimens with chemically stabilised flue gas ashes from waste incineration. However, the quantities leached were still...

[A difficult stabilisation. Chlorpromazine in the fifties in Belgium].

Science.gov (United States)

Majerus, Benoît

2010-01-01

Through a Belgian case study the article tries to trace the gradual stabilisation of chlorpromazine as an antipsychotic in the 1950s. By varying ranges and angles of approach it shows the heterogeneity of actors involved and the semantic bricolage that accompany the marketing of the first antipsychotic. Far from being a revolution, the presence of Largactil in psychiatric practice is rather characterised by integration into a wider range of medicines and sinuous searching to give sense to this new drug.

Graphene nanosheet-induced toughening of yttria-stabilized zirconia

Energy Technology Data Exchange (ETDEWEB)

Su, Jianan; Chen, Yao; Huang, Qiqi [Soochow University, School of Mechanical and Electric Engineering, Collaborative Innovation Center of Suzhou Nano Science and Technology, Suzhou (China)

2017-01-15

Graphene nanosheet (GNS)-reinforced yttria-stabilized tetragonal zirconia polycrystals (TZP) were synthesized using spark plasma sintering (SPS), and the influences of the added GNSs on microstructure evolution and the microscopic mechanical properties of the sintered composites were investigated. Raman spectroscopy and microstructure observation corroborated that these added GNSs, which can survive the harsh SPS processing condition, homogeneously distribute in the matrix of all composites to hinder significantly the grain growth. In comparison with the monolithic TZP, the indentation fracture toughness of a GNS/TZP composite reaches maximum value and increases by up to ∝36% (from ∝4.1 to ∝5.6 MPa m{sup 0.5}) even at 0.5% weight fraction, GNS pullout, crack bridging, crack deflection, and crack branching are responsible for the increased fracture toughness. The computed energy dissipation by GNS pullout decreases with increasing the number of graphene layers due to weak bonding between them, and therefore, graphene agglomeration would impair toughening effect. Moreover, scratch studies suggest that GNS/TZP composites exhibit improved scratch resistance due to the fact that GNSs are promising reinforcing and lubricating nanofillers in ceramic composites. (orig.)

Interfacial behaviour of sodium stearoyllactylate (SSL) as an oil-in-water pickering emulsion stabiliser.

Science.gov (United States)

Kurukji, D; Pichot, R; Spyropoulos, F; Norton, I T

2013-11-01

The ability of a food ingredient, sodium stearoyllactylate (SSL), to stabilise oil-in-water (O/W) emulsions against coalescence was investigated, and closely linked to its capacity to act as a Pickering stabiliser. Results showed that emulsion stability could be achieved with a relatively low SSL concentration (≥0.1 wt%), and cryogenic-scanning electron microscopy (cryo-SEM) visualisation of emulsion structure revealed the presence of colloidal SSL aggregates adsorbed at the oil-water interface. Surface properties of SSL could be modified by altering the size of these aggregates in water; a faster decrease in surface tension was observed when SSL dispersions were subjected to high pressure homogenisation (HPH). The rate of SSL adsorption at the sunflower oil-water interface also increased after HPH, and a higher interfacial tension (IFT) was observed with increasing SSL concentration. Differential scanning calorimetry (DSC) enabled a comparison of the thermal behaviour of SSL in aqueous dispersions with SSL-stabilised O/W emulsions. SSL melting enthalpy depended on emulsion interfacial area and the corresponding DSC data was used to determine the amount of SSL adsorbed at the oil-water interface. An idealised theoretical interfacial coverage calculation based on Pickering emulsion theory was in general agreement with the mass of SSL adsorbed as predicted by DSC. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Effect of boron oxide on the cubic-to-monoclinic phase transition in yttria-stabilized zirconia

International Nuclear Information System (INIS)

Florio, D.Z. de; Muccillo, R.

2004-01-01

Specimens of yttria fully stabilized zirconia with different amounts of boron oxide have been studied by X-ray diffraction at room temperature and at higher temperatures up to 1250 deg. C. A boron oxide-assisted cubic-to-monoclinic phase transformation was determined in the temperature range 800-1250 deg. C. In situ high temperature X-ray diffraction experiments gave evidences of the dependence of the phase transformation on the heating rate. The possibility of tuning the cubic-monoclinic phase ratio by suitable addition of boron oxide before pressing and sintering is proposed

The effect of sintering temperature on the 3Y-TZP co-doped with equimolar addition of the yttria and niobia

International Nuclear Information System (INIS)

Fonseca, Flavia Baccaro; Dorat, Daniele Ramos; Melo, Francisco Cristovao Lourenco de; Piorino Neto, Francisco; Reis, Danieli Aparecida

2010-01-01

The aim of this work is to identify the better sintering temperature to densify zirconia co-doped with yttria and niobia and to verify the existence of the stable tetragonal phase (t´) under applied stress at room temperature to be applied as a TBC material. Four compositions with equimolar addition of yttria and niobia in the 3Y-TZP were produced, 13.0 %, 14.5 %, 16.0 % and 17.5 %. The mixtures were prepared in high energy ball milling for 10 minutes and the samples prepared on uniaxial and isostatic pressing. The selected sintering temperatures were 1500 deg C, 1550 deg C, 1600 deg C and 1650 deg C, for 1 hour. Analysis of conventional and high resolution X-Ray Diffraction and measures of specific mass by Archimedes method were performed. Through measures of the specific mass, the best sintering temperature was 1550 deg C, with relative specific mass above 95 %. The x-ray diffraction analysis indicate a probable existence of t´ in all samples. (author)

Microscopic observation of laser glazed yttria-stabilized zirconia coatings

Science.gov (United States)

Morks, M. F.; Berndt, C. C.; Durandet, Y.; Brandt, M.; Wang, J.

2010-08-01

Thermal barrier coatings (TBCs) are frequently used as insulation system for hot components in gas-turbine, combustors and power plant industries. The corrosive gases which come from combustion of low grade fuels can penetrate into the TBCs and reach the metallic components and bond coat and cause hot corrosion and erosion damage. Glazing the top coat by laser beam is advanced approach to seal TBCs surface. The laser beam has the advantage of forming a dense thin layer composed of micrograins. Plasma-sprayed yttria-stabilized zirconia (YSZ) coating was glazed with Nd-YAG laser at different operating conditions. The surface morphologies, before and after laser treatment, were investigated by scanning electron microscopy. Laser beam assisted the densification of the surface by remelting a thin layer of the exposed surface. The laser glazing converted the rough surface of TBCs into smooth micron-size grains with size of 2-9 μm and narrow grain boundaries. The glazed surfaces showed higher Vickers hardness compared to as-sprayed coatings. The results revealed that the hardness increases as the grain size decreases.

Stabilisation of Clay Soil with Lime and Melon Husk Ash for use in Farm Structures

Directory of Open Access Journals (Sweden)

I. S. Mohammed

2014-08-01

Full Text Available The rising cost of traditional stabilising agents and the need for economical utilisation of industrial and agricultural waste for beneficial engineering purposes has encouraged an investigation into the stabilization of clay soil with lime and melon husk ash. The chemical composition of the melon husk ash that was used in stabilising clay soil was determined. The clay soil was divided into two parts, one part was used to determine the index properties while the other part was treated at British Standard Light (BSL compaction energy with 0 %, 2 %, 4 %, 6 % and 8 % melon husk ash by dry weight of the soil and each was admixed with 2 %, 4 %, 6 % and 8 % lime. The stabilised clay soil was cured for 7, 14 and 28 days before the unconfined compressive strength were determined while the coefficients of permeability of the stabilised clay soil were also determined at 28 days of curing. The data obtained from the experiment was subjected to analysis of variance to examine the significance at 5% level. Results showed that the natural clay soil belong to A-7-6 or CH (clay of high plasticity in the American Association of State Highway Transportation Official (AASHTO and Unified Soil Classification System (1986. The chemical composition of the ash had aluminum oxide, iron oxide and silicon dioxide values of 18.5%, 2.82% and 51.24% respectively. The unconfined compressive strength and coefficient of permeability of the natural clay soil was determined to be 285 kN/m2 and 1.45 x 10-5 cm/s, respectively. Increase in melon husk ash and lime percent increases the unconfined compressive strength (UCS of the stabilised clay soil significantly (p < 0.05 and decrease the coefficient of permeability when compared with the natural clay soil. The peak values of unconfined compressive strength for 7, 14 and 28 days of curing are 1200 kN/m2, 1598 kN/m2 and 1695 kN/m2 respectively at 6% MHA and 8% lime content while the lowest value for coefficient of permeability was 0

En route vers la nano stabilisation de CLIC faisceau principale et focalisation finale

CERN Document Server

Artoos, K; Guinchard, M; Hauviller, Claude; Lackner, F; CERN. Geneva. TS Department

2008-01-01

Pour atteindre la luminosité voulue de CLIC, la taille transversale du faisceau doit être de l?ordre du nanomètre. Ceci nécessite une stabilité vibratoire des quadripôles du faisceau principal de 1 nm et même 0.1 nm pour les doublets de la focalisation finale. La nano technologie et la nano stabilisation sont des activités qui évoluent rapidement dans l?industrie et centres de recherche pour des applications très variées comme l?électronique, l?optique, la chimie voire la médecine. Cette présentation décrit les avancées techniques nécessaires pour atteindre l?objectif de CLIC et les projets et collaborations R&D prévus pour démontrer la faisabilité de la nano stabilisation de CLIC en 2010.

The fictional transition of the preferential orientation of yttria-stabilized zirconia thin films

International Nuclear Information System (INIS)

Lamas, J.S.; Leroy, W.P.; Depla, D.

2012-01-01

The fundamental study of the microstructural and textural evolution of yttria-stabilized zirconia (YSZ) thin films is of great importance given that the crystallographic properties are intimately related to their extrinsic or functional properties. In order to study these properties, YSZ thin films were obtained using dual magnetron sputtering. The results of a polar plot graph, based on X-ray diffraction (XRD) data, seem to indicate a transition from [200] out-of-plane preferential orientation to [111], indicating a dependence on composition and yttrium target–substrate (Y T–S) distance at low pressure. However, no transition is identified at high pressure, showing only [111] out-of-plane orientation, independent of composition and Y T–S distance. Scanning electron microscopy (SEM) indicates a tilt in the columnar structure of the film but no other microstructural change is in evidence, possibly related to the growth transition from [200] to [111]. Pole figures were used to clarify the texture transition in the YSZ thin films. These results indicate that there is indeed no transition in the preferential orientation of the films from [200] to [111] but a tilt of the [200] orientation towards the zirconium source. Detailed study using pole figures and SEM, clearly indicated that no growth zone transition was present and the effect is caused by geometrical configuration, contradicting expectations from standard θ/2θ XRD measurements. - Highlights: ► Study of the preferential orientation of Yttria-stabilized zirconia thin films ► Comparison of the preferential orientation at two different chamber pressures ► Correlation with the energy per adparticle and the extended structure zone model ► Use of pole figures analyses to clarify the change in the preferential orientation

The fictional transition of the preferential orientation of yttria-stabilized zirconia thin films

Energy Technology Data Exchange (ETDEWEB)

Lamas, J.S., E-mail: Jerika.Lamas@UGent.be; Leroy, W.P.; Depla, D.

2012-12-15

The fundamental study of the microstructural and textural evolution of yttria-stabilized zirconia (YSZ) thin films is of great importance given that the crystallographic properties are intimately related to their extrinsic or functional properties. In order to study these properties, YSZ thin films were obtained using dual magnetron sputtering. The results of a polar plot graph, based on X-ray diffraction (XRD) data, seem to indicate a transition from [200] out-of-plane preferential orientation to [111], indicating a dependence on composition and yttrium target-substrate (Y T-S) distance at low pressure. However, no transition is identified at high pressure, showing only [111] out-of-plane orientation, independent of composition and Y T-S distance. Scanning electron microscopy (SEM) indicates a tilt in the columnar structure of the film but no other microstructural change is in evidence, possibly related to the growth transition from [200] to [111]. Pole figures were used to clarify the texture transition in the YSZ thin films. These results indicate that there is indeed no transition in the preferential orientation of the films from [200] to [111] but a tilt of the [200] orientation towards the zirconium source. Detailed study using pole figures and SEM, clearly indicated that no growth zone transition was present and the effect is caused by geometrical configuration, contradicting expectations from standard {theta}/2{theta} XRD measurements. - Highlights: Black-Right-Pointing-Pointer Study of the preferential orientation of Yttria-stabilized zirconia thin films Black-Right-Pointing-Pointer Comparison of the preferential orientation at two different chamber pressures Black-Right-Pointing-Pointer Correlation with the energy per adparticle and the extended structure zone model Black-Right-Pointing-Pointer Use of pole figures analyses to clarify the change in the preferential orientation.

Room temperature growth of biaxially aligned yttria-stabilized zirconia films on glass substrates by pulsed-laser deposition

CERN Document Server

Li Peng; Mazumder, J

2003-01-01

Room temperature deposition of biaxially textured yttria-stabilized zirconia (YSZ) films on amorphous glass substrates was successfully achieved by conventional pulsed-laser deposition. The influence of the surrounding gases, their pressure and the deposition time on the structure of the films was studied. A columnar growth process was revealed based on the experimental results. The grown biaxial texture appears as a kind of substrate independence, which makes it possible to fabricate in-plane aligned YSZ films on various substrates.

Metastable SUSY breaking, de Sitter moduli stabilisation and Kaehler moduli inflation

International Nuclear Information System (INIS)

Krippendorf, Sven; Quevedo, Fernando

2009-01-01

We study the influence of anomalous U(1) symmetries and their associated D-terms on the vacuum structure of global field theories once they are coupled to N = 1 supergravity and in the context of string compactifications with moduli stabilisation. In particular, we focus on a IIB string motivated construction of the ISS scenario and examine the influence of one additional U(1) symmetry on the vacuum structure. We point out that in the simplest one-Kaehler modulus compactification, the original ISS vacuum gets generically destabilised by a runaway behaviour of the potential in the modulus direction. In more general compactifications with several Kaehler moduli, we find a novel realisation of the LARGE volume scenario with D-term uplifting to de Sitter space and both D-term and F-term supersymmetry breaking. The structure of soft supersymmetry breaking terms is determined in the preferred scenario where the standard model cycle is not stabilised non-perturbatively and found to be flavour universal. Our scenario also provides a purely supersymmetric realisation of Kaehler moduli (blow-up and fibre) inflation, with similar observational properties as the original proposals but without the need to include an extra (non-SUSY) uplifting term.

The detection and stabilisation of limit cycle for deterministic finite automata

Science.gov (United States)

Han, Xiaoguang; Chen, Zengqiang; Liu, Zhongxin; Zhang, Qing

2018-04-01

In this paper, the topological structure properties of deterministic finite automata (DFA), under the framework of the semi-tensor product of matrices, are investigated. First, the dynamics of DFA are converted into a new algebraic form as a discrete-time linear system by means of Boolean algebra. Using this algebraic description, the approach of calculating the limit cycles of different lengths is given. Second, we present two fundamental concepts, namely, domain of attraction of limit cycle and prereachability set. Based on the prereachability set, an explicit solution of calculating domain of attraction of a limit cycle is completely characterised. Third, we define the globally attractive limit cycle, and then the necessary and sufficient condition for verifying whether all state trajectories of a DFA enter a given limit cycle in a finite number of transitions is given. Fourth, the problem of whether a DFA can be stabilised to a limit cycle by the state feedback controller is discussed. Criteria for limit cycle-stabilisation are established. All state feedback controllers which implement the minimal length trajectories from each state to the limit cycle are obtained by using the proposed algorithm. Finally, an illustrative example is presented to show the theoretical results.

Characterisation of the Ni/ScYSZ interface in a model solid oxide fuel cell anode

DEFF Research Database (Denmark)

Schmidt, Michael Stenbæk; Hansen, Karin Vels; Norrman, Kion

2008-01-01

A nickel point electrode setup was used as a model of an SOFC anode on three slightly different electrolytes of zirconia stabilised by co-doping with scandia and yttria. The effect of electrolyte impurities on the electrode polarisation resistance was investigated by correlating electrochemical...... impedance spectroscopy data with time-of-flight secondary ion mass spectrometry, scanning electron microscopy and atomic force microscopy data. A semi-quantitative analysis of the electrolyte surfaces showed that the levels of surface impurities inside the electrode/electrolyte interface in close proximity...

Novel solid – solid phase change material based on polyethylene glycol and cellulose used for temperature stabilisation

Directory of Open Access Journals (Sweden)

Wojda Marta

2014-01-01

Full Text Available Thermal management is one of crucial issues in the development of modern electronic devices. In the recent years interest in phase change materials (PCMs as alternative cooling possibility has increased significantly. Preliminary results concerning the research into possibility of the use of solid-solid phase change materials (S-S PCMs for stabilisation temperature of electronic devices has been presented in the paper. Novel solid-solid phase change material based on polyethylene glycol and cellulose has been synthesized. Attempt to improve its thermal conductivity has been taken. Material has been synthesized for the purpose of stabilisation of temperature of electronic devices.

The streamline upwind Petrov-Galerkin stabilising method for the numerical solution of highly advective problems

Directory of Open Access Journals (Sweden)

Carlos Humberto Galeano Urueña

2009-05-01

Full Text Available This article describes the streamline upwind Petrov-Galerkin (SUPG method as being a stabilisation technique for resolving the diffusion-advection-reaction equation by finite elements. The first part of this article has a short analysis of the importance of this type of differential equation in modelling physical phenomena in multiple fields. A one-dimensional description of the SUPG me- thod is then given to extend this basis to two and three dimensions. The outcome of a strongly advective and a high numerical complexity experiment is presented. The results show how the version of the implemented SUPG technique allowed stabilised approaches in space, even for high Peclet numbers. Additional graphs of the numerical experiments presented here can be downloaded from www.gnum.unal.edu.co.

Stabilising greenhouse gas concentrations at low levels. An assessment of options and costs

Energy Technology Data Exchange (ETDEWEB)

Van Vuuren, D.P.; Den Elzen, M.G.J.; Lucas, P.L.; Eickhout, B.; Strengers, B.J.; Van Ruijven, B.; Berk, M.M.; De Vries, H.J.M.; Wonink, S.J.; Van den Houdt, R.; Oostenrijk, R. [Netherlands Environmental Assessment Agency MNP, Bilthoven (Netherlands); Hoogwijk, M. [Ecofys, Utrecht (Netherlands); Meinshausen, M. [Potsdam Institute for Climate Impact Research PIK, Postdam (Germany)

2006-10-15

Preventing 'dangerous anthropogenic interference of the climate system' may require stabilisation of greenhouse gas concentrations in the atmosphere at relatively low levels such as 550 ppm CO2-eq. and below. Relatively few studies exist that have analysed the possibilities and implications of meeting such stringent climate targets. This report presents a series of related papers that address this issue - either by focusing on individual options or by presenting overall strategies at the global and regional level. The results show that it is technically possible to reach ambitious climate targets - with abatement costs for default assumptions in the order of 1-2% of global GDP. To achieve these lower concentration levels, global emissions need to peak within 15-20 years. The stabilisation scenarios use a large portfolio of measures, including energy efficiency but also carbon capture and storage, large scale application of bio-energy, reduction of non-CO2 gasses, increased use of renewable and/or nuclear power and carbon plantations.

Effect of nanoparticles generation method on ionic conductivity in Yttria stabilized zirconia

International Nuclear Information System (INIS)

Khare, J.; Joshi, M.P.; Kukreja, L.M.; Satapathy, S.

2013-01-01

Yttria stabilized zirconia nanoparticles were generated in pulsed and CW mode of laser operation using CO 2 laser based laser vaporization method. Impedance spectroscopic measurements were carried out in frequency range of 100 Hz - 1 MHz at various temperatures ranging from room temperature to 500 C. The deconvolution of grain and grain boundary contribution were obtained from impedance spectra by an equivalent circuit analysis. Grain and grain boundary ionic conductivity of pellet made from nanoparticles generated in pulsed mode was two orders of magnitude large in comparison to pellets made from nanoparticles generated in CW mode of laser operation. The difference in ionic conductivities of pellets made from nanoparticles generated in pulsed mode and CW mode were explained on the basis of defect associations in nanoparticles produced during nanoparticles generation. (author)

Yttria-stabilized zirconia as membrane material for electrolytic deoxidation of CaO-CaCl{sub 2} melts

Energy Technology Data Exchange (ETDEWEB)

Martin, A.; Poignet, J. C.; Fouletier, J. [Univ Grenoble, LEPMI, CNRS, INPG, UJF, F-38402 St Martin Dheres (France); Allibert, M. [LPSC, F-38026 Grenoble 1 (France); Lambertin, D. [SPDE, CEA Marcoule, F-30207 Bagnols Sur Ceze (France); Bourges, G. [SRPU, CEA Valduc, F-21120 Is Sur Tille (France)

2010-07-01

This article is devoted to the study of the stability of an yttria-stabilized zirconia membrane used in the electrolysis of molten CaCl{sub 2}-CaO mixtures at 850 degrees C. Intentiostatic and potentiostatic electrolysis were carried for periods ranging from 10 to 20 h. Post-mortem composition profiles across the zirconia membrane were determined using Raman spectroscopy and microprobe analysis. The membrane degradation was analyzed in terms of synergetic parameters, i. e., chemical, electrochemical, and thermomechanical effects. (authors)

Deposition of yttria stabilized zirconia layer for solid oxide fuel cell by chemical vapor infiltration

International Nuclear Information System (INIS)

John, John T.; Dubey, Vivekanand; Kain, Vivekanand; Dey, Gautham Kumar; Prakash, Deep

2011-01-01

Free energy associated with a chemical reaction can be converted into electricity, if we can split the reaction into an anodic reaction and a cathodic reaction and carry out the reactions in an electrochemical cell using electrodes that will catalyze the reactions. We also have to use a suitable electrolyte, that serves to isolate the chemical species in the two compartments from getting mixed directly but allow an ion produced in one of the reactions to proceed to the other side and complete the reaction. For this reason cracks and porosity are not tolerated in the electrolyte. First generation solid oxide fuel cell (SOFC) uses yttria stabilized zirconia (YSZ) as the electrolyte. In spite of the fact that several solid electrolytes with higher conductivities at lower temperature are being investigated and developed, 8 mol% yttria stabilized zirconia (8YSZ) is considered to be the most favored electrolyte for the SOFC today. The electrolyte should be present as a thin, impervious layer of uniform thickness with good adherence, chemical and mechanical stability, in between the porous cathode and anode. Efforts to produce the 8YSZ coatings on porous lanthanum strontium manganite tubes by electrochemical vapor deposition (ECVD) have met with unexpected difficulties such as impurity pick up and chemical and mechanical instability of the LSM tubes in the ECVD environment. It was also difficult to keep the chemical composition of the YSZ coating at exactly 8 mol% Yttria in zirconia and to control the coating thickness in tight control. These problems were overcome by a two step deposition process where a YSZ layer of required thickness was produced by electrophoretic coating from an acetyl acetone bath at a voltage of 30-300V DC and sintered at 1300 deg C. The resulting porous YSZ layer was made impervious by chemical vapor infiltration (CVI) by the reaction between a mixture of vapors of YCl 3 and ZrCl 4 and steam at 1300 deg C as in the case of ECVD for a short

Defect structure of yttria-stabilized zirconia and its influence on the ionic conductivity at elevated temperatures

DEFF Research Database (Denmark)

Goff, J.P.; Hayes, W.; Hull, S.

1999-01-01

The defect structure of cubic fluorite structured yttria-stabilized zirconia (ZrO2)(1-x)(Y2O3)(x) has been investigated over the composition range 0.100(3)less than or equal to x less than or equal to 0.241 (10) and temperatures T(K) up to 2780(10) K, using single-crystal specimens. Analysis of n......, we propose that the anomalous decrease in the ionic conductivity with increasing x is a consequence of the decreasing mobility of the isolated defects, possibly due to blockage by the increasing number of static aggregates....

Green synthesis of highly concentrated aqueous colloidal solutions of large starch-stabilised silver nanoplatelets.

Science.gov (United States)

Cheng, Fei; Betts, Jonathan W; Kelly, Stephen M; Hector, Andrew L

2015-01-01

A simple, environmentally friendly and cost-effective method has been developed to prepare a range of aqueous silver colloidal solutions, using ascorbic acid as a reducing agent, water-soluble starch as a combined crystallising, stabilising and solubilising agent, and water as the solvent. The diameter of silver nanoplatelets increases with higher concentrations of AgNO3 and starch. The silver nanoparticles are also more uniform in shape the greater the diameter of the nanoparticles. Colloidal solutions with a very high concentration of large, flat, hexagonal silver nanoplatelets (~230 nm in breadth) have been used to deposit and fix an antibacterial coating of these large starch-stabilised silver nanoplates on commercial cotton fibres, using a simple dip-coating process using water as the solvent, in order to study the dependence of the antibacterial properties of these nanoplatelets on their size. Copyright © 2014 Elsevier B.V. All rights reserved.

Controlling Microstructure of Yttria-Stabilized Zirconia Prepared from Suspensions and Solutions by Plasma Spraying with High Feed Rates.

Czech Academy of Sciences Publication Activity Database

Mušálek, Radek; Medřický, Jan; Tesař, Tomáš; Kotlan, Jiří; Pala, Zdeněk; Lukáč, František; Illková, Ksenia; Hlína, Michal; Chráska, Tomáš; Sokołowski, P.; Curry, N.

2017-01-01

Roč. 26, č. 8 (2017), s. 1787-1803 ISSN 1059-9630 R&D Projects: GA ČR GA15-12145S Institutional support: RVO:61389021 Keywords : hybrid plasma torch * microstructure * solution * precursor spraying * suspension spraying * thermal barrier * coatings (TBCs) * water-stabilized plasma * yttria-stabilized zirconia (YSZ) Subject RIV: JK - Corrosion ; Surface Treatment of Materials OBOR OECD: Coating and films Impact factor: 1.488, year: 2016 https://link.springer.com/ article /10.1007/s11666-017-0622-x

Normal spectral emittance of Inconel 718 aeronautical alloy coated with yttria stabilized zirconia films

Energy Technology Data Exchange (ETDEWEB)

Gonzalez-Fernandez, L. [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain); Industria de Turbo Propulsores, S.A., Planta de Zamudio, Edificio 300, 48170 Zamudio, Bizkaia (Spain); Campo, L. del [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain); Perez-Saez, R.B., E-mail: raul.perez@ehu.es [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain); Tello, M.J. [Departamento de Fisica de la Materia Condensada, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco, Barrio Sarriena s/n, 48940 Leioa, Bizkaia (Spain)

2012-02-05

Highlights: Black-Right-Pointing-Pointer Emittance of Inconel 718 coated with plasma sprayed yttria stabilized zirconia. Black-Right-Pointing-Pointer The coating is opaque for {lambda} > 9 {mu}m and semi-transparent for {lambda} < 9 {mu}m. Black-Right-Pointing-Pointer In the semi-transparent region the emittance decreases with coating thickness. Black-Right-Pointing-Pointer 300 {mu}m thick coatings are still semi-transparent. Black-Right-Pointing-Pointer In the opaque region the surface roughness determines the emittance level. - Abstract: Knowledge of the radiative behaviour of the yttria stabilized zirconia (YSZ) thermal barrier coatings (TBCs) is needed to perform radiative heat transfer calculations in industrial applications. In this paper, normal spectral emittance experimental data of atmospheric plasma sprayed (PS) YSZ films layered on Inconel 718 substrates are shown. The spectral emittance was measured between 2.5 and 22 {mu}m on samples with film thicknesses ranging from 20 to 280 {mu}m. The samples were heated in a controlled environment, and the emittance was measured for several temperatures between 330 and 730 Degree-Sign C. The dependence of the spectral emittance with film thickness, surface roughness and temperature has been studied and compared with the available results for YSZ TBCs obtained by electron-beam physical vapour deposition. The PS-TBC samples show a Christiansen point at {lambda} = 12.8 {mu}m. The films are semi-transparent for {lambda} < 9 {mu}m, and opaque for {lambda} > 9 {mu}m. In the semi-transparent region, the contribution of the radiation emitted by the Inconel 718 substrate to the global emittance of the samples is analysed. In addition, the influence of the roughness in the emittance values in the opaque spectral region is discussed. Finally, the total normal emittance is obtained as a function of the TBC thickness.

Effect of impurities on structural and electrochemical properties of the Ni-YSZ interface

DEFF Research Database (Denmark)

Jensen, Karin Vels; Wallenberg, R.; Chorkendorff, I.

2003-01-01

. The results were compared to earlier investigations of a less pure nickel/YSZ interface. The pure interface developed different structures depending on whether or not the samples were polarised. Despite,the purity of the nickel, impurities were found in the interfacial region. The pure electrodes......The changes in interface structure and chemical composition of a 99.995% pure nickel/yttria-stabilised zirconia (YSZ) interface were examined after heat treatment at 1000degreesC in 97% H-2/3% H2O with and without polarisation. Impedance spectroscopy was used for electrochemical characterisation...

Aquatic treadmill water level influence on pelvic limb kinematics in cranial cruciate ligament-deficient dogs with surgically stabilised stifles.

Science.gov (United States)

Bertocci, G; Smalley, C; Brown, N; Bialczak, K; Carroll, D

2018-02-01

To compare pelvic limb joint kinematics and temporal gait characteristics during land-based and aquatic-based treadmill walking in dogs that have undergone surgical stabilisation for cranial cruciate ligament deficiency. Client-owned dogs with surgically stabilised stifles following cranial cruciate ligament deficiency performed three walking trials consisting of three consecutive gait cycles on an aquatic treadmill under four water levels. Hip, stifle and hock range of motion; peak extension; and peak flexion were assessed for the affected limb at each water level. Gait cycle time and stance phase percentage were also determined. Ten client-owned dogs of varying breeds were evaluated at a mean of 55·2 days postoperatively. Aquatic treadmill water level influenced pelvic limb kinematics and temporal gait outcomes. Increased stifle joint flexion was observed as treadmill water level increased, peaking when the water level was at the hip. Similarly, hip flexion increased at the hip water level. Stifle range of motion was greatest at stifle and hip water levels. Stance phase percentage was significantly decreased when water level was at the hip. Aquatic treadmill walking has become a common rehabilitation modality following surgical stabilisation of cranial cruciate ligament deficiency. However, evidence-based best practice guidelines to enhance stifle kinematics do not exist. Our findings suggest that rehabilitation utilising a water level at or above the stifle will achieve the best stifle kinematics following surgical stifle stabilisation. © 2017 British Small Animal Veterinary Association.

A new methodology for studying nanoparticle interactions in biological systems: Dispersing titania in biocompatible media using chemical stabilisers

Science.gov (United States)

Ramirez-Garcia, Sonia; Chen, Lan; Morris, Michael A.; Dawson, Kenneth A.

2011-11-01

We report here a highly successful and original protocol for the dispersion of nanoparticles in biocompatible fluids for in vitro and in vivo studies of the nanoparticle-biology interaction. Titania is chosen as a suitable model as it is one of the priority materials listed by the OECD and small particles of the anatase structure are extensively used as e.g. photocatalysts in solar cells. Consequently, its delivery into the environment and its interaction with biological organisms is unavoidable. Therefore, its biological effect needs to be understood. In this work, we prepared stable nanoparticle dispersions of anatase aggregates using citrate stabilisations between 45 and 55 nm at concentrations of up to 10 mg mL-1. The optimum pH for this type of suspension was 7, resulting in ζ-potentials of approximately -50 mV. The stabilised aggregates were the subject of dialysis to produce stable dispersions without the chemical stabiliser, thus allowing studies in the absence of potentially toxic chemicals. Different sizing techniques such as Dynamic Light Scattering (DLS), Nanoparticle Tracking Analysis (NTA) and Differential Centrifuge Sedimentation (DCS) were used to characterise the different suspensions. The results obtained with each of these techniques are compared and a critical analysis of the suitability of each technique is given.We report here a highly successful and original protocol for the dispersion of nanoparticles in biocompatible fluids for in vitro and in vivo studies of the nanoparticle-biology interaction. Titania is chosen as a suitable model as it is one of the priority materials listed by the OECD and small particles of the anatase structure are extensively used as e.g. photocatalysts in solar cells. Consequently, its delivery into the environment and its interaction with biological organisms is unavoidable. Therefore, its biological effect needs to be understood. In this work, we prepared stable nanoparticle dispersions of anatase aggregates

Solid dispersions based on inulin for the stabilisation and formulation of delta 9-tetrahydrocannabinol

NARCIS (Netherlands)

van Drooge, D J; Hinrichs, W L J; Wegman, K A M; Visser, M R; Eissens, A C; Frijlink, H W

2004-01-01

The aim of this study was to develop a dry powder formulation that stabilises the chemically labile lipophilic Delta(9)-tetrahydrocannabinol (THC), that rapidly dissolves in water in order to increase the bioavailability and that opens new routes of administration. It was investigated whether these

Input and output constraints-based stabilisation of switched nonlinear systems with unstable subsystems and its application

Science.gov (United States)

Chen, Chao; Liu, Qian; Zhao, Jun

2018-01-01

This paper studies the problem of stabilisation of switched nonlinear systems with output and input constraints. We propose a recursive approach to solve this issue. None of the subsystems are assumed to be stablisable while the switched system is stabilised by dual design of controllers for subsystems and a switching law. When only dealing with bounded input, we provide nested switching controllers using an extended backstepping procedure. If both input and output constraints are taken into consideration, a Barrier Lyapunov Function is employed during operation to construct multiple Lyapunov functions for switched nonlinear system in the backstepping procedure. As a practical example, the control design of an equilibrium manifold expansion model of aero-engine is given to demonstrate the effectiveness of the proposed design method.

Hardness Enhancement of STS304 Deposited with Yttria Stabilized Zirconia by Aerosol Deposition Method

Energy Technology Data Exchange (ETDEWEB)

Lim, Il-Ho; Park, Chun-Kil; Kim, Hyung Sun; Jeong, Dea-Yong [Inha University, Incheon (Korea, Republic of); Lee, Yong-Seok [Sodoyeon Co., Yeoju (Korea, Republic of); Kong, Young-Min [University of Ulsan, Ulsan (Korea, Republic of); Kang, Kweon Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-03-15

To improve the surface hardness of the STS304, Yttria stabilized zirconia (YSZ) films with nano-sized grain were deposited by an aerosol-deposition (AD) method. Coating layers showed dense structure and had -5µm thickness. When 3 mol% YSZ powders with tetragonal phase were deposited on STS304 substrate, tetragonal structure was transformed to cubic structure due to the high impact energy during the AD process. At the same time, strong impact by YSZ particles allowed the austenite phase in STS304 to be transformed into martensite phase. Surface hardness measured with nano indentor showed that YSZ coated film had 11.5 GPa, which is larger value than 7 GPa of STS304.

Ionic conductivity and thermal stability of magnetron-sputtered nanocrystalline yttria-stabilized zirconia

DEFF Research Database (Denmark)

Sillassen, M.; Eklund, P.; Sridharan, M.

2009-01-01

Thermally stable, stoichiometric, cubic yttria-stabilized zirconia (YSZ) thin-film electrolytes have been synthesized by reactive pulsed dc magnetron sputtering from a Zr–Y (80/20 at. %) alloy target. Films deposited at floating potential had a texture. Single-line profile analysis of the 111 x.......5% at bias voltages of −175 and −200 V with additional incorporation of argon. The films were thermally stable; very limited grain coarsening was observed up to an annealing temperature of 800 °C. Temperature-dependent impedance spectroscopy analysis of the YSZ films with Ag electrodes showed that the in......-plane ionic conductivity was within one order of magnitude higher in films deposited with substrate bias corresponding to a decrease in grain size compared to films deposited at floating potential. This suggests that there is a significant contribution to the ionic conductivity from grain boundaries...

Effects of NiO addition on the densification, microstructure and electrical conductivity of Yttria fully-stabilized zirconia

International Nuclear Information System (INIS)

Batista, Rafael Morgado

2010-01-01

The effects produced by NiO addition to yttria fully-stabilized zirconia were systematically investigated. Commercial zirconia-8 mol% yttria, nickel acetate, nitrate, trihydroxycarbonate and nickel oxide were used as starting materials. The NiO content varied from 0.5 to 5 mol%, and the compositions were prepared by mechanically mixing the starting materials in the stoichiometric proportions. Densification studies carried out by density and dilatometry measurements revealed that the maximum shrinkage (∼16-∼20%) depends on the type of nickel precursor. In the second sintering stage the linear shrinkage increased with increasing NiO content (precursor: nickel trihydroxy-carbonate). In the first sintering stage, the activation energy for grain boundary diffusion changed according to the additive precursor, being lower for the oxide and higher for the trihydroxy-carbonate. In the second stage, when the major part of porosity is eliminated, the maximum shrinkage rate temperatures were found to be independent on the precursor except when nickel acetate is used. The solubility limit at 1350 degree C is 1.48% as determined by X-ray diffraction. Above the solubility limit the excess NiO is retained as a second randomly distributed phase. The main effect of the additive in the ceramic microstructure is to increase the average grain size. The electrical measurements showed that the additive did not produce any significant effect in the grain conductivity irrespective of the sintering time, except when the precursor material was nickel oxide. In this case, the grain conductivity increased with increasing sintering time. This effect is attributed to the crystallite size of the nickel oxide precursor, which is higher than that of 8YSZ, slowing down the formation of solid solution. However, the grain conductivity of samples prepared with nickel trihydroxy-carbonate precursor is slightly lower than those of other samples. The samples sintered for 15 h exhibited an additional

Correlation between inter-vertebral disc morphology and the results in patients undergoing Graf ligament stabilisation.

Science.gov (United States)

Askar, Zahid; Wardlaw, Douglas; Muthukumar, Thillainayagamike; Smith, Frank; Kader, Deiary; Gibson, Suzy

2004-12-01

Previous studies have shown Graf ligament stabilisation procedure to give mixed results in the short to medium term. The aim of this study was to correlate the pre-operative state of the disc, multifidus muscles, age of the patient, levels operated and the clinical outcome after a mean follow-up of 47 months. Graf ligament stabilisation procedure was carried out in 38 patients between 1996 and 1999. Their post-operative status was assessed using MacNab criteria. The post-operative follow-up was by postal questionnaires and review of the clinical notes. Disc morphology and multifidus muscle wasting was graded blindly and independently. The intra- and interobserver reliability was measured with kappa score and classified using the kappa classification of Landis and Koch. Correlation was measured with the help of Spearman correlation coefficient. Thirty-eight patients (100%) returned the questionnaires. Mean follow-up time was 47.55 months. Fifty-nine levels were operated on. Mean age was 39.68 years. The overall re-operation rate was 15.8%. The intra- and interobserver reliability was graded as good to substantial. Twenty-two patients (57.89%) were satisfied with the procedure. There was no statistically significant correlation between disc morphology, multifidus muscle wasting, sex, age, number of levels operated, the levels operated, and the satisfaction rate. The indications of Graf ligament stabilisation procedure are not clear. Further work is necessary to clearly identify the indication for the procedure.

The effect of Al intermediate layer on thermal resistance of EB-PVD yttria-stabilized zirconia coatings on titanium substrate

Science.gov (United States)

Panin, Alexey; Panin, Victor; Kazachenok, Marina; Shugurov, Artur; Sinyakova, Elena; Martynov, Sergey; Rusyaev, Andrey; Kasterov, Artur

2017-12-01

The yttria-stabilized zirconia coatings sprayed on titanium substrates by the electron beam physical vapor deposition were subjected to thermal annealing in air at 1000°C for 1, 30 and 60 min. The delamination and fracture of the coatings are studied by the scanning electron microscopy and X-ray diffraction. It is shown that a magnetron sputtered Al interlayer between the coating and the substrate considerably improves the thermal resistance of ceramic coatings.

Phase stabilisation of hexagonal barium titanate doped with transition metals: A computational study

International Nuclear Information System (INIS)

Dawson, J.A.; Freeman, C.L.; Harding, J.H.; Sinclair, D.C.

2013-01-01

Interatomic potentials recently developed for the modelling of BaTiO 3 have been used to explore the stabilisation of the hexagonal polymorph of BaTiO 3 by doping with transition metals (namely Mn, Co, Fe and Ni) at the Ti-site. Classical simulations have been completed on both the cubic and hexagonal polymorphs to investigate the energetic consequences of transition metal doping on each polymorph. Ti-site charge compensation mechanisms have been used for the multi-valent transition metal ions and cluster binding energies have been considered. Simulations show a significant energetic gain when doping occurs at Ti sites in the face sharing dimers (Ti 2 sites) of the hexagonal polymorph compared with the doping of the cubic polymorph. This energetic difference between the two polymorphs is true for all transition metals tested and all charge states and in the case of tri- and tetra-valent dopants negative solution energies are found for the hexagonal polymorph suggesting actual polymorph stabilisation occurs with the incorporation of these ions as observed experimentally. Oxidation during incorporation of Ni 2+ and Fe 3+ ions has also been considered. - Graphical abstract: The representation of the strongest binding energy clusters for tri-valent dopants—(a) Ti 2 /O 1 cluster and (b) Ti 2 /O 2 cluster. Highlights: ► Classical simulations show a significant energetic gain when doping occurs at Ti sites in the face sharing dimers (Ti2 sites) of the hexagonal polymorph compared with the doping of the cubic polymorph. ► This energetic difference between the two polymorphs is true for all transition metals tested and all charge states. ► In the case of tri- and tetra- valent dopants negative solution energies are found for the hexagonal polymorph suggesting actual polymorph stabilisation occurs with the incorporation of these ions

Satisfactory short-term outcomes of the STABILISE technique for type B aortic dissection.

Science.gov (United States)

Melissano, Germano; Bertoglio, Luca; Rinaldi, Enrico; Mascia, Daniele; Kahlberg, Andrea; Loschi, Diletta; De Luca, Monica; Monaco, Fabrizio; Chiesa, Roberto

2018-03-29

The aim of this study was to evaluate the perioperative and short-term results in a cohort of patients treated during the last year at our institution with the stent-assisted balloon-induced intimal disruption and relamination in aortic dissection repair (STABILISE) technique for acute complicated aortic dissection. Between June 2016 and June 2017, 10 patients (all male; mean age, 62.6 ± 7.4 years) received treatment for acute complicated aortic dissection with the STABILISE technique. After a standard provisional extension to induce complete attachment procedure using the commercially available endovascular dissection system (Cook Medical, Bloomington, Ind), the distal stent graft area and the bare stent area were ballooned to completely exclude the thoracic false lumen (FL) and to obtain a single-channeled abdominal aorta. Computed tomography was routinely performed within the first postoperative week before discharge and then at 3 months, at 6 months, and yearly thereafter. The technical and clinical success rates were analyzed. The 30-day technical and clinical success rates were 100%, with complete thrombosis of the thoracic FL and no type I endoleak. Malperfusion was resolved in all cases. No aortic ruptures were recorded, and no open conversion was required. One case of delayed spinal cord ischemia fully resolved within the discharge period. Predischarge computed tomography showed complete thrombosis of the thoracic FL in all cases. In two cases, some degree of patency of the abdominal FL was observed. At short-term follow-up, the overall aortic diameters remained stable with no further dilation. The STABILISE technique was safe and feasible in this cohort of patients, with complete thrombosis of the thoracic FL and creation of a single-channeled aorta in most cases. Further studies are needed to ascertain the long-term behavior of the treated aorta. Copyright © 2018 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

Stabilisation of the grain market by the flexible use of grain for bioethanol

NARCIS (Netherlands)

Helming, J.F.M.; Pronk, A.; Woltjer, I.

2010-01-01

This report reviews whether the grain market and grain price can be stabilised by the variation of the use of grain in the EU-27's production of bioethanol. The time horizon of this study is 2020, whereby account is taken of the minimum 10% obligation for biofuel use in the EU-27. An economic

Integration of vehicle yaw stabilisation and rollover prevention through nonlinear hierarchical control allocation

Science.gov (United States)

Alberding, Matthäus B.; Tjønnås, Johannes; Johansen, Tor A.

2014-12-01

This work presents an approach to rollover prevention that takes advantage of the modular structure and optimisation properties of the control allocation paradigm. It eliminates the need for a stabilising roll controller by introducing rollover prevention as a constraint on the control allocation problem. The major advantage of this approach is the control authority margin that remains with a high-level controller even during interventions for rollover prevention. In this work, the high-level control is assigned to a yaw stabilising controller. It could be replaced by any other controller. The constraint for rollover prevention could be replaced by or extended to different control objectives. This work uses differential braking for actuation. The use of additional or different actuators is possible. The developed control algorithm is computationally efficient and suitable for low-cost automotive electronic control units. The predictive design of the rollover prevention constraint does not require any sensor equipment in addition to the yaw controller. The method is validated using an industrial multi-body vehicle simulation environment.

Use of lignite fly ash as an additive in alkaline stabilisation and pasteurisation of wastewater sludge

Energy Technology Data Exchange (ETDEWEB)

Kocaer, F.O.; Alkan, U.; Baskaya, H.S. [Uludag University, Bursa (Turkey). Faculty of Engineering & Architecture

2003-10-01

The possibility of using lignite fly ash in low doses for reducing the pathogen levels in wastewater sludge was investigated. The results showed that using fly ash alone in doses of 40%,80% and 120% (on a dry weight basis), did not produce an alkaline environment for an efficient removal of pathogens. However, using fly ash in conjunction with the minimum amount of quicklime may act as an effective way of fecal coliform removal in both alkaline stabilisation and pasteurisation processes. It was shown that using fly ash in doses of 80% and 120% in alkaline stabilisation and pasteurisation processes prevented the pH decays and regrowth of pathogens during 60 days of storage period. The results of the study confirmed that alkaline pasteurisation process produces a product which is more resistant to pH decays and regrowth of fecal coliforms compared to that of alkaline stabilisation. Consequently, the overall results of this study indicated that the minimum lime and fly ash dosages required to generate a Class B biosolid were 10-15% and 80%, respectively. On the other hand, heating sludge to 50{degree}C prior to the addition of 10-15% quicklime and 80% fly ash followed by further heating to 70{degree}C and then sustaining at this temperature for 30 minutes were sufficient to generate a Class A biosolid.

Anisotropic modulus stabilisation. Strings at LHC scales with micron-sized extra dimensions

Energy Technology Data Exchange (ETDEWEB)

Cicoli, M. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Burgess, C.P. [McMaster Univ., Hamilton (Canada). Dept. of Physics and Astronomy; Perimeter Institute for Theoretical Physics, Waterloo (Canada); Quevedo, F. [Cambridge Univ. (United Kingdom). DAMTP/CMS; Abdus Salam International Centre for Theoretical Physics, Trieste (Italy)

2011-04-15

We construct flux-stabilised Type IIB string compactifications whose extra dimensions have very different sizes, and use these to describe several types of vacua with a TeV string scale. Because we can access regimes where two dimensions are hierarchically larger than the other four, we find examples where two dimensions are micron-sized while the other four are at the weak scale in addition to more standard examples with all six extra dimensions equally large. Besides providing ultraviolet completeness, the phenomenology of these models is richer than vanilla large-dimensional models in several generic ways: (i) they are supersymmetric, with supersymmetry broken at sub-eV scales in the bulk but only nonlinearly realised in the Standard Model sector, leading to no MSSM superpartners for ordinary particles and many more bulk missing-energy channels, as in supersymmetric large extra dimensions (SLED); (ii) small cycles in the more complicated extra-dimensional geometry allow some KK states to reside at TeV scales even if all six extra dimensions are nominally much larger; (iii) a rich spectrum of string and KK states at TeV scales; and (iv) an equally rich spectrum of very light moduli exist having unusually small (but technically natural) masses, with potentially interesting implications for cosmology and astrophysics that nonetheless evade new-force constraints. The hierarchy problem is solved in these models because the extra-dimensional volume is naturally stabilised at exponentially large values: the extra dimensions are Calabi-Yau geometries with a 4D K3-fibration over a 2D base, with moduli stabilised within the well-established LARGE-Volume scenario. The new technical step is the use of poly-instanton corrections to the superpotential (which, unlike for simpler models, are present on K3-fibered Calabi-Yau compactifications) to obtain a large hierarchy between the sizes of different dimensions. For several scenarios we identify the low-energy spectrum and

Anisotropic modulus stabilisation. Strings at LHC scales with micron-sized extra dimensions

International Nuclear Information System (INIS)

Cicoli, M.; Burgess, C.P.; Quevedo, F.

2011-04-01

We construct flux-stabilised Type IIB string compactifications whose extra dimensions have very different sizes, and use these to describe several types of vacua with a TeV string scale. Because we can access regimes where two dimensions are hierarchically larger than the other four, we find examples where two dimensions are micron-sized while the other four are at the weak scale in addition to more standard examples with all six extra dimensions equally large. Besides providing ultraviolet completeness, the phenomenology of these models is richer than vanilla large-dimensional models in several generic ways: (i) they are supersymmetric, with supersymmetry broken at sub-eV scales in the bulk but only nonlinearly realised in the Standard Model sector, leading to no MSSM superpartners for ordinary particles and many more bulk missing-energy channels, as in supersymmetric large extra dimensions (SLED); (ii) small cycles in the more complicated extra-dimensional geometry allow some KK states to reside at TeV scales even if all six extra dimensions are nominally much larger; (iii) a rich spectrum of string and KK states at TeV scales; and (iv) an equally rich spectrum of very light moduli exist having unusually small (but technically natural) masses, with potentially interesting implications for cosmology and astrophysics that nonetheless evade new-force constraints. The hierarchy problem is solved in these models because the extra-dimensional volume is naturally stabilised at exponentially large values: the extra dimensions are Calabi-Yau geometries with a 4D K3-fibration over a 2D base, with moduli stabilised within the well-established LARGE-Volume scenario. The new technical step is the use of poly-instanton corrections to the superpotential (which, unlike for simpler models, are present on K3-fibered Calabi-Yau compactifications) to obtain a large hierarchy between the sizes of different dimensions. For several scenarios we identify the low-energy spectrum and

Is coracoclavicular stabilisation alone sufficient for the endoscopic treatment of severe acromioclavicular joint dislocation (Rockwood types III, IV, and V)?

Science.gov (United States)

Barth, J; Duparc, F; Andrieu, K; Duport, M; Toussaint, B; Bertiaux, S; Clavert, P; Gastaud, O; Brassart, N; Beaudouin, E; De Mourgues, P; Berne, D; Bahurel, J; Najihi, N; Boyer, P; Faivre, B; Meyer, A; Nourissat, G; Poulain, S; Bruchou, F; Ménard, J F

2015-12-01

The primary objective was to evaluate correlations linking anatomical to functional outcomes after endoscopically assisted repair of acute acromioclavicular joint dislocation (ACJD). Combined acromioclavicular and coracoclavicular stabilisation improves radiological outcomes compared to coracoclavicular stabilisation alone. A prospective multicentre study was performed. Clinical outcome measures were pain intensity on a visual analogue scale (VAS), subjective functional impairment (QuickDASH score), and Constant's score. Anatomical outcomes were assessed on standard radiographs (anteroposterior view of the acromioclavicular girdle and bilateral axillary views) obtained preoperatively and postoperatively and on postoperative dynamic radiographs taken as described by Tauber et al. Of 116 patients with acute ACJD included in the study, 48% had type III, 30% type IV, and 22% type V ACJD according to the Rockwood classification. Coracoclavicular stabilisation was achieved using a double endobutton in 93% of patients, and concomitant acromioclavicular stabilisation was performed in 50% of patients. The objective functional outcome was good, with an unweighted Constant's score ≥ 85/100 and a subjective QuickDASH functional disability score ≤ 10 in 75% of patients. The radiographic analysis showed significant improvements from the preoperative to the 1-year postoperative values in the vertical plane (decrease in the coracoclavicular ratio from 214 to 128%, p=10(-6)) and in the horizontal plane (decrease in posterior displacement from 4 to 0mm, p=5×10(-5)). The anatomical outcome correlated significantly with the functional outcome (absolute R value=0.19 and p=0.045). We found no statistically significant differences across the various types of constructs used. Intra-operative control of the acromioclavicular joint did not improve the result. Implantation of a biological graft significantly improved both the anatomical outcome in the vertical plane (p=0.04) and

Inacessible Andean sites reveal land-use induced stabilisation of soil organic carbon

Science.gov (United States)

Heitkamp, Felix; Maqsood, Shafique; Sylvester, Steven; Kessler, Michael; Jungkunst, Hermann

2015-04-01

Human activity affects properties and development of ecosystems across the globe to such a degree that it is challenging to get baseline values for undisturbed ecosystems. This is especially true for soils, which are affected by land-use history and hold a legacy of past human interventions. Therefore, it is still largely unknown how soil would have developed "naturally" and if processes of organic matter stabilisation would be different in comparison to managed soils. Here, we show undisturbed soil development, i.e., the processes of weathering and accumulation of soil organic carbon (SOC), by comparing pristine with grazed sites in the high Andes (4500 m) of southern Peru. We located study plots on a large ledge (0.2 km²) that is only accessible with mountaineering equipment. Plots with pristine vegetation were compared to rangeland plots that were constantly under grazing management for at least four millennia. All "state factors"; climate, potential biota, topography, parent material and time; besides "land-use" were, therefore, identical. Vegetation change, induced by grazing management, led to lower vegetation cover of the soil, thereby increasing soil surface temperatures and soil acidification. Both factors increased weathering in rangeland soils, as indicated by the presence of pedogenic oxides, especially amorphous Al-(oxy)hydroxides (oxalate-extractable Al). Higher losses of base cations (K, Na, Ca) and lower pH-values were related to a low base saturation of exchange sites in rangelands. Therefore, rangeland soils were classified as Umbrisol, whereas soils under pristine vegetation were classified as Phaeozeme. All profiles were rich in SOC (100 to 126 g kg-1) with no significant differences in concentrations or stocks. SOC of rangeland soils was, however, less available for microorganisms (proportion of microbial C on SOC: 1.8 vs. 0.6% in pristine and rangeland soils, respectively) and showed higher stability against thermal degradation. Reasons for

Food-grade Pickering stabilisation of foams by in situ hydrophobisation of calcium carbonate particles

NARCIS (Netherlands)

Binks, Bernard P.; Muijlwijk, K.; Koman, Henriëtte; Poortinga, A.T.

2017-01-01

The aim of this study was to investigate the possibility of stabilising foam bubbles in water by adsorption of calcium carbonate (CaCO3) particles. Because CaCO3 is hydrophilic and not surface-active, particles were hydrophobised in situ with several emulsifiers. The used emulsifiers were food-grade

Food-grade pickering stabilisation of foams by in situ hydrophobisation of calcium carbonate particles

NARCIS (Netherlands)

Binks, B.P.; Muijlwijk, K.; Koman, H.; Poortinga, A.T.

2017-01-01

The aim of this study was to investigate the possibility of stabilising foam bubbles in water by adsorption of calcium carbonate (CaCO3) particles. Because CaCO3 is hydrophilic and not surface-active, particles were hydrophobised in situ with several emulsifiers. The used emulsifiers were food-grade

Dorsal surgical stabilisation using tension bands for treatment of traumatic atlanto-occipital instability in a cat.

Science.gov (United States)

Vedrine, B; Maurin, M P

2017-12-01

An atlanto-occipital instability secondary to a dog bite was diagnosed in a 4-year-old Persian cat. Dorsal stabilisation of the instability was made with two OrthoFiber prostheses (Securos), which were used as tension bands between the nuchal crests of the occipital bone and the spinous process of the axis. Total recovery was achieved 4 days after surgery. Normal alignment of the atlanto-occipital joint was observed on survey radiographs taken 6 weeks post-surgery. Although the right loop had failed, the alignment was still normal and no neurological after-effects could be identified. Dorsal divergent tension bands between the nuchal crests of the occipital bone and the spinous process of the axis can be used to stabilise traumatic atlanto-occipital instability. © 2017 Australian Veterinary Association.

Global output feedback stabilisation of stochastic high-order feedforward nonlinear systems with time-delay

Science.gov (United States)

Zhang, Kemei; Zhao, Cong-Ran; Xie, Xue-Jun

2015-12-01

This paper considers the problem of output feedback stabilisation for stochastic high-order feedforward nonlinear systems with time-varying delay. By using the homogeneous domination theory and solving several troublesome obstacles in the design and analysis, an output feedback controller is constructed to drive the closed-loop system globally asymptotically stable in probability.

The problem of oxidation state stabilisation and some regularities of a Periodic system of the elements

International Nuclear Information System (INIS)

Kiselev, Yurii M; Tretyakov, Yuri D

1999-01-01

The general principles of the concept of oxidation state stabilisation are formulated. Problems associated with the preparation and provision of the highest valent forms of transition elements are considered. The empirical data concerning the synthesis of new compounds of rare-earth elements and d elements in unusually high oxidation states are analysed. The possibility of occurrence of the oxidation states + 9 and + 10 for some elements (for example, for iridium and platinum in tetraoxo ions) are discussed. Approaches to the realisation of these states are outlined and it is demonstrated that solid phases or matrices containing alkali metal cations are the most promising systems for the stabilisation of these high oxidation states. Selected thermodynamic features typical of metal halides and oxides and the regularities of the changes in the extreme oxidation states of d elements are considered. The bibliography includes 266 references.

Evaluation of technetium-99m exametazime stabilised with cobalt chloride as a blood flow tracer in focal cerebral ischaemia

Energy Technology Data Exchange (ETDEWEB)

Gartshore, G [Wellcome Surgical Inst. and Hugh Fraser Neuroscience Labs., Glasgow Univ. (United Kingdom); Bannan, P [Wellcome Surgical Inst. and Hugh Fraser Neuroscience Labs., Glasgow Univ. (United Kingdom); Patterson, J [Wellcome Surgical Inst. and Hugh Fraser Neuroscience Labs., Glasgow Univ. (United Kingdom); Higley, B [Wellcome Surgical Inst. and Hugh Fraser Neuroscience Labs., Glasgow Univ. (United Kingdom); McCulloch, J [Wellcome Surgical Inst. and Hugh Fraser Neuroscience Labs., Glasgow Univ. (United Kingdom)

1994-09-01

A protocol has been devised to effectively extend the limited post-reconstitution shelf life of technetium-99m exametazime as a radiopharmaceutical for imaging cerebral blood flow (CBF) distribution. The potential of [sup 99m]Tc-exametazime stabilised with cobalt chloride for imaging CBF distribution as late as 4 h after reconstitution has been examined in ischaemic and non-ischaemic tissue in halothane-anaesthetised cats. Focal cerebral ischaemia was produced by permanent middle cerebral artery occlusion. The relationship between [sup 99m]Tc-exametazime uptake and retention and CBF (assessed with [[sup 14]C]iodoantipyrine 10 min after first radiopharmaceutical administration) was determined in the same tissue section with double label autoradiography. Over the CBF range 0 - 80 ml 100 g[sup -1] min[sup -1], the uptake of [sup 99m]Tc-exametazime (quantitatively and topographically) was linearly related to CBF irrespective of whether the [sup 99m]Tc-labelled tracer was unstabilised (and administered within 10 min of reconstitution) or was stabilised with cobalt chloride (and administered up to 240 min after reconstitution). For levels of CBF in excess of 80 ml 100 g[sup -1] min[sup -1] the excellent topographical relationship between [sup 99m]Tc-exametazime distribution and CBF is maintained but quantitatively, [sup 99m]Tc-exametazime underestimates CBF to a similar degree in animals receiving stabilised and unstabilised [sup 99m]Tc-exametazime. The presence of the stabiliser, cobalt chloride, extends greatly the period over which [sup 99m]Tc-exametazime can be used after reconstitution to generate images of CBF distribution in normal and ischaemic cerebral tissue. (orig.)

SiC fiber and yttria-stabilized zirconia composite thick thermal barrier coatings fabricated by plasma spray

Science.gov (United States)

Ma, Rongbin; Cheng, Xudong; Ye, Weiping

2015-12-01

Approximately 4 mm-thick SiC fiber/yttria-stabilized zirconia (YSZ) composite thermal barrier coatings (TBCs) were prepared by atmospheric plasma spray (APS). The composite coatings have a 'reinforced concrete frame structure', which can protect the coating from failure caused by increasing thickness of coating. The SiC fiber plays an important role in reducing the residual stress level of the composite coatings. The thermal conductivity (TC) value of the composite coatings is 0.632 W/m K, which is about 50% reduction compared to that of typical APS YSZ TBCs. And the composite coatings have higher fracture toughness and better thermal shock resistance than the YSZ TBCs.

A Note on the Effects of the Income Stabilisation Tool on Income Inequality in Agriculture

NARCIS (Netherlands)

Finger, R.; Benni, El N.

2014-01-01

Increasing concerns with income risks in agriculture have led to discussions on the introduction of an Income Stabilisation Tool (IST) in Europe. In this note, we extend existing evaluations of the IST by investigating the potential effect of the IST on inequality in farm incomes using Swiss

Leachability and heavy metal speciation of 17-year old stabilised/solidified contaminated site soils

Energy Technology Data Exchange (ETDEWEB)

Wang, Fei, E-mail: fwtiffany@gmail.com [Department of Engineering, University of Cambridge, Trumpington Street, Cambridge CB2 1PZ (United Kingdom); Wang, Hailing, E-mail: wanghailing@njtech.edu.cn [College of Environment, Nanjing Tech University, Nanjing 210009 (China); Al-Tabbaa, Abir, E-mail: aa22@cam.ac.uk [Department of Engineering, University of Cambridge, Trumpington Street, Cambridge CB2 1PZ (United Kingdom)

2014-08-15

Highlights: • The effectiveness of the cement-based S/S at 17 years in West Drayton site is still satisfactory. • Major leaching of Cu, Zn, Ni, Cd and Pb in all mixes took place in the Fe/Mn oxides phase. • The hydration process has been fully completed and further carbonation took place at 17 years. • Microstructure analyses show that unreacted PFA exists. - Abstract: The long-term leachability, heavy metal speciation transformation and binding mechanisms in a field stabilised/solidified contaminated soil (made ground) from West Drayton site were recently investigated following in situ auger mixing treatment with a number of cement-based binders back in 1996. Two batch leaching tests (TCLP and BS EN 12457) and a modified five step sequential extraction procedure along with X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses were employed for the testing of the 17-year-old field soil. The results of batch leaching tests show that the treatment employed remained effective at 17 years of service time, with all BS EN 12457 test samples and most of TCLP test samples satisfied drinking water standards. Sequential extraction results illustrate that the leaching of Cu, Ni, Zn, Pb and Cd in all mixes mainly occurred at the Fe/Mn phase, ranging from 43% to 83%. Amongst the five metals tested, Ni was the most stable with around 40% remained in the residual phase for all the different cement-based binder stabilised/solidified samples. XRD and SEM analyses show that the hydration process has been fully completed and further carbonation took place. In summary, this study confirms that such cement-based stabilisation/solidification (S/S) treatment can achieve satisfactory durability and thus is a reliable technique for long-term remediation of heavy metal contaminated soil.

Preparation of highly stabilised natural rubber latex for radiation vulcanisation

International Nuclear Information System (INIS)

Kulatunge, S.S.; Nadarajah, M.; Kalyani, N.M.V.; Chandralal, H.N.K.K.; Devendra, R.

1996-01-01

There is a bright future for radiation vulcanised natural rubber latex (RVNRL) but there are problems in manufacturing it as the centrifuged latex to be used for radiation has to be kept for at least a month or sometimes even three to six months before adding the sensitisers and even then the latex sometimes coagulates on adding the sensitisers. This paper describes a process by which the latex can be stabilised by addition of an anionic soap before centrifuging so that it has a high mechanical stability and hence can be used even within one week of the manufacture of the centrifuged latex

Fabrication of yttria microcapsules for radiotherapy from water/oil emulsion

International Nuclear Information System (INIS)

Miyazaki, Toshiki; Kai, Tomohiro; Ishida, Eiichi; Kawashita, Masakazu; Hiraoka, Masahiro

2010-01-01

Radiotherapy using ceramic microparticles that act as β-emitters after neutron bombardment is attractive as a minimally invasive option for cancer treatment. Yttria (Y 2 O 3 ) microcapsules (20-30 μm in diameter) are capable of cutting off the nutrition supply in cancer cells through an embolization effect. In the present study, Y 2 O 3 microcapsules were prepared via precipitation of yttrium hydroxide from a water/oil (W/O) emulsion and a subsequent heat treatment. The emulsion was prepared by dispersing yttrium hydroxide sol in 2-ethyl-1-hexanol. Microcapsules were obtained by an addition of the emulsion in butanol via dehydration and subsequent aggregation of the yttrium hydroxide. The effects of the rotation speed and surfactant concentration on the diameter of the particles were investigated. The diameter of the microcapsules showed a tendency to decrease with increases in rotation speed during emulsion preparation or surfactant concentration in the oil phase. A high yield of the Y 2 O 3 microcapsules with a diameter of 20-30 μm were obtained after a heat treatment at the optimized rotation speed and surfactant concentration. The obtained microcapsules showed high chemical durability in a simulated body environment. (author)

Polarity control and growth mode of InN on yttria-stabilized zirconia (111) surfaces

International Nuclear Information System (INIS)

Kobayashi, Atsushi; Okubo, Kana; Ohta, Jitsuo; Oshima, Masaharu; Fujioka, Hiroshi

2012-01-01

We have found that polarity of epitaxial InN layers has been controlled by choice of a capping material during high-temperature annealing of yttria-stabilized zirconia (YSZ) (111) substrates in air. Angle-resolved X-ray photoelectron spectroscopy has revealed that the amount of segregation of Y atoms to the YSZ surface depended on the capping material of the substrates. In-polar and N-polar InN have been reproducibly grown on Y-segregated and Y-segregation-free YSZ surfaces, respectively. We have also found that the growth of the first monolayer (ML) of N-polar InN proceeds in a step-flow mode which then switches to layer-by-layer mode after the coverage by 1-ML-thick InN. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Analysis of designed experiments by stabilised PLS Regression and jack-knifing

DEFF Research Database (Denmark)

Martens, Harald; Høy, M.; Westad, F.

2001-01-01

Pragmatical, visually oriented methods for assessing and optimising bi-linear regression models are described, and applied to PLS Regression (PLSR) analysis of multi-response data from controlled experiments. The paper outlines some ways to stabilise the PLSR method to extend its range...... the reliability of the linear and bi-linear model parameter estimates. The paper illustrates how the obtained PLSR "significance" probabilities are similar to those from conventional factorial ANOVA, but the PLSR is shown to give important additional overview plots of the main relevant structures in the multi....... An Introduction, Wiley, Chichester, UK, 2001]....

Thermal shock behaviour of mullite-bonded porous silicon carbide ceramics with yttria addition

International Nuclear Information System (INIS)

Ding Shuqiang; Zeng Yuping; Jiang Dongliang

2007-01-01

Thermal shock resistance of mullite (3Al 2 O 3 · 2SiO 2 )-bonded porous silicon carbide (SiC) ceramics with 3.0 wt% yttria (Y 2 O 3 ) addition was evaluated by a water-quenching technique. The thermal shock damage was investigated as a function of the quenching temperature, quenching cycles and specimen thickness. The residual flexural strength of the quenched specimens decreases with increasing quenching temperature and specimen thickness due to the larger thermal stress caused by thermal shock. However, quenching cycles at the temperature difference of 1200 deg. C have no effect on the residual strength since the same thermal stress was produced in repeated thermal shock processes. The good thermal shock damage resistance of the specimens is contributed mainly by the low strength and moderate elastic modulus. Moreover, the pores prevent the continuous propagation of cracks and alleviate further damage

Consolidation of Partially Stabilized ZrO2 in the Presence of a Noncontacting Electric Field

Science.gov (United States)

Majidi, Hasti; van Benthem, Klaus

2015-05-01

Electric field-assisted sintering techniques demonstrate accelerated densification at lower temperatures than the conventional sintering methods. However, it is still debated whether the applied field and/or resulting currents are responsible for the densification enhancement. To distinguish the effects of an applied field from current flow, in situ scanning transmission electron microscopy experiments with soft agglomerates of partially stabilized yttria-doped zirconia particles are carried out. A new microelectromechanical system-based sample support is used to heat particle agglomerates while simultaneously exposing them to an externally applied noncontacting electric field. Under isothermal condition at 900 °C , an electric field strength of 500 V /cm shows a sudden threefold enhancement in the shrinkage of the agglomerates. The applied electrostatic potential lowers the activation energy for point defect formation within the space charge zone and therefore promotes consolidation. Obtaining similar magnitudes of shrinkage in the absence of any electric field requires a higher temperature and longer time.

Remediation by in-situ solidification/stabilisation of Ardeer landfill, Scotland

International Nuclear Information System (INIS)

Wyllie, M.; Esnault, A.; Barker, P.

1997-01-01

The Ardeer Landfill site at ICI Explosives factory on the west coast of Scotland had been a repository for waste from the site for 40 years. In order to safeguard the local environment ICI Explosives, with approval of Local Authorities and the Clyde River Purification Board put into action a programme of investigation and planning which culminated in the in-situ treatment of 10,000 m3 of waste within the landfill by a deep mixing method using the open-quotes Colmixclose quotes system. The paper describes in varying degrees of detail the remediation from investigation to the execution of the in-situ stabilisation and presents the post construction monitoring results

Immobilised native plant cysteine proteases: packed-bed reactor for white wine protein stabilisation.

Science.gov (United States)

Benucci, Ilaria; Lombardelli, Claudio; Liburdi, Katia; Acciaro, Giuseppe; Zappino, Matteo; Esti, Marco

2016-02-01

This research presents a feasibility study of using a continuous packed-bed reactor (PBR), containing immobilised native plant cysteine proteases, as a specific and mild alternative technique relative to the usual bentonite fining for white wine protein stabilisation. The operational parameters for a PBR containing immobilised bromelain (PBR-br) or immobilised papain (PBR-pa) were optimised using model wine fortified with synthetic substrate (Bz-Phe-Val-Arg-pNA). The effectiveness of PBR-br, both in terms of hazing potential and total protein decrease, was significantly higher than PBR-pa, in all the seven unfined, white wines used. Among the wines tested, Sauvignon Blanc, given its total protein content as well as its very high intrinsic instability, was selected as a control wine to evaluate the effect of the treatment on wine as to its soluble protein profile, phenolic composition, mineral component, and sensory properties. The treatment in a PBR containing immobilised bromelain appeared effective in decreasing both wine hazing potential and total protein amount, while it did not significantly affect the phenol compounds, the mineral component nor the sensory quality of wine. The enzymatic treatment in PBR was shown to be a specific and mild technique for use as an alternative to bentonite fining for white wine protein stabilisation.

Carbon nanoparticle stabilised liquid|liquid micro-interfaces for electrochemically driven ion-transfer processes

International Nuclear Information System (INIS)

MacDonald, Stuart M.; Fletcher, Paul D.I.; Cui Zhenggang; Opallo, Marcin; Chen Jingyuan; Marken, Frank

2007-01-01

Stabilised liquid|liquid interfaces between an organic 4-(3-phenylpropyl)-pyridine (PPP) phase and an aqueous electrolyte phase are obtained in the presence of suitable nanoparticles. The use of nanoparticulate stabilisers (ca. 30 nm diameter laponite or 9-18 nm diameter carbon) in 'Pickering' emulsion systems allows stable organic microdroplets to be formed and these are readily deposited onto conventional tin-doped indium oxide (ITO) electrodes. In contrast to the electrically insulating laponite nanoparticles, conducting carbon nanoparticles are shown to effectively catalyse the simultaneous electron transfer and ion transfer process at triple phase boundary junctions. Anion transfer processes between the aqueous and organic phase are driven electrochemically at the extensive triple phase junction carbon nanoparticle|4-(3-phenylpropyl)-pyridine|aqueous electrolyte. The organic phase consists of a redox active reagent 5,10,15,20-tetraphenyl-21H,23H-porphinato manganese(III) (MnTPP + ), 5,10,15,20-tetraphenyl-21H,23H-porphinato iron(III) (FeTPP + ), or proto-porphyrinato-IX iron(III) (hemin) dissolved in 4-(3-phenylpropyl)-pyridine (PPP). The composition of the aqueous electrolyte phase determines the reversible potential for the Nernstian anion transfer process. The methodology is shown to be versatile and, in future, could be applied more generally in liquid|liquid electroanalysis

Voltage-stabilised elastomers with increased relative permittivity and high electrical breakdown strength by means of phase separating binary copolymer blends of silicone elastomers

DEFF Research Database (Denmark)

A Razak, Aliff Hisyam; Yu, Liyun; Skov, Anne Ladegaard

2017-01-01

Increased electrical breakdown strength and increased dielectric permittivity of silicone-based dielectric elastomers are achieved by means of the addition of so-called voltage-stabilisers prepared from PDMS–PPMS copolymers as well as PDMS–PEG copolymers in order to compensate for the negative...... effect of softness on electrical stability of silicone elastomers. The voltage-stabilised elastomer, incorporating a high-permittivity PDMS–PEG copolymer, possesses increased relative permittivity, high electrical breakdown strength, excellent network integrity and low dielectric loss and paves the way...

Stabilised frequency of extreme positive Indian Ocean Dipole under 1.5 °C warming.

Science.gov (United States)

Cai, Wenju; Wang, Guojian; Gan, Bolan; Wu, Lixin; Santoso, Agus; Lin, Xiaopei; Chen, Zhaohui; Jia, Fan; Yamagata, Toshio

2018-04-12

Extreme positive Indian Ocean Dipole (pIOD) affects weather, agriculture, ecosystems, and public health worldwide, particularly when exacerbated by an extreme El Niño. The Paris Agreement aims to limit warming below 2 °C and ideally below 1.5 °C in global mean temperature (GMT), but how extreme pIOD will respond to this target is unclear. Here we show that the frequency increases linearly as the warming proceeds, and doubles at 1.5 °C warming from the pre-industrial level (statistically significant above the 90% confidence level), underscored by a strong intermodel agreement with 11 out of 13 models producing an increase. However, in sharp contrast to a continuous increase in extreme El Niño frequency long after GMT stabilisation, the extreme pIOD frequency peaks as the GMT stabilises. The contrasting response corresponds to a 50% reduction in frequency of an extreme El Niño preceded by an extreme pIOD from that projected under a business-as-usual scenario.

Tribological and wear behavior of yttria stabilized zirconia thermal barrier coatings on mild steel

International Nuclear Information System (INIS)

Farooq, M.; Pervez, A.

2012-01-01

The perfection of the temperature confrontation of the engine essentials can be obtained by claim of a single ceramic thermal barrier coating (TBC) or several composite layers. Engine elements protected by TBC can work safely in elevated temperature range above 1000 degree C. Continuous endeavor to increase thermal resistance of engine the elements requires, apart from laboratory investigations, also numerical study of the different engine parts. The high temperatures and stress concentrations can act as the local sources of damage initiation and defects propagation in the form of cracks. The current study focuses the development of Yttria stabilized zirconia thermal barrier coating by Thermal spray technique. Mild steel was used as a substrate and the coating was then characterized for tribological analysis followed by the optical analysis of wear tracks and found the TBC behavior more promising then steel. (author)

Processing-structure-property relationships in electron beam physical vapor deposited yttria stabilized zirconia coatings

International Nuclear Information System (INIS)

Rao, D. Srinivasa; Valleti, Krishna; Joshi, S. V.; Janardhan, G. Ranga

2011-01-01

The physical and mechanical properties of yttria stabilized zirconia (YSZ) coatings deposited by the electron beam physical vapor deposition technique have been investigated by varying the key process variables such as vapor incidence angle and sample rotation speed. The tetragonal zirconia coatings formed under varying process conditions employed were found to have widely different surface and cross-sectional morphologies. The porosity, phase composition, planar orientation, hardness, adhesion, and surface residual stresses in the coated specimens were comprehensively evaluated to develop a correlation with the process variables. Under transverse scratch test conditions, the YSZ coatings exhibited two different crack formation modes, depending on the magnitude of residual stress. The influence of processing conditions on the coating deposition rate, column orientation angle, and adhesion strength has been established. Key relationships between porosity, hardness, and adhesion are also presented.

Immobilised native plant cysteine proteases: packed-bed reactor for white wine protein stabilisation

OpenAIRE

Benucci, Ilaria; Lombardelli, Claudio; Liburdi, Katia; Acciaro, Giuseppe; Zappino, Matteo; Esti, Marco

2015-01-01

This research presents a feasibility study of using a continuous packed-bed reactor (PBR), containing immobilised native plant cysteine proteases, as a specific and mild alternative technique relative to the usual bentonite fining for white wine protein stabilisation. The operational parameters for a PBR containing immobilised bromelain (PBR-br) or immobilised papain (PBR-pa) were optimised using model wine fortified with synthetic substrate (Bz-Phe-Val-Arg-pNA). The effectiveness of PBR-br, ...

CFD predictions of wake-stabilised jet flames in a cross-flow

International Nuclear Information System (INIS)

Lawal, Mohammed S.; Fairweather, Michael; Gogolek, Peter; Ingham, Derek B.; Ma, Lin; Pourkashanian, Mohamed; Williams, Alan

2013-01-01

This study describes an investigation into predicting the major flow properties in wake-stabilised jet flames in a cross flow of air using first- and second-order turbulence models, applied within a RANS (Reynolds-averaged Navier–Stokes) modelling framework. Standard and RNG (re-normalisation group) versions of the k-ε turbulence model were employed at the first-order level and the results compared with a second-moment closure, or RSM (Reynolds stress model). The combustion process was modelled using the laminar flamelet approach together with a thermal radiation model using the discrete ordinate method. The ability of the various turbulence models to reproduce experimentally established flame appearance, profiles of velocity and turbulence intensity, as well as the combustion efficiency of such flames is reported. The results show that all the turbulence models predict similar velocity profiles over the majority of the flow domain considered, except in the wake region, where the predictions of the RSM and RNG k-ε models are in closer agreement with experimental data. In contrast, the standard k-ε model over-predicts the peak turbulence intensity. Also, it is found that the RSM provides superior predictions of the planar recirculation and flame zones attached to the release pipe in the wake region. - Highlights: ► We investigated the prediction of the major properties in wake-stabilised methane jet flames in a cross flow. ► The ability of the various turbulence models to reproduce experimentally established flame parameters is reported. ► All the turbulence models considered predict similar velocity profiles, except in the wake region

Suspensions on the basis of stabilised zirconium oxide for three-dimensional printing

Science.gov (United States)

Sokolov, P. S.; Komissarenko, D. A.; Shmeleva, I. A.; Slyusar, I. V.; Dosovitskiy, G. A.; Evdokimov, P. V.; Putlyaev, V. I.; Dosovitskiy, A. E.

2018-04-01

Present work considers the first results on rheological and photo-curing behaviour of suspension consisting of nanocrystalline stabilised zirconium dioxide powders (19 - 27 vol. %) and a liquid UV-photosensitive organic monomer. At ambient temperature compositions showed a viscosity of 2.5 and 0.8 Pa×s at 10 and 100 s-1 shear rates, respectively. Printability of these compositions was subsequently investigated by using an stereolithography machine Ember (Autodesk). 3D objects were later sintered in a separate furnace into dense translucent ZrO2 ceramics.

Rapid, cool sintering of wet processed yttria-stabilized zirconia ceramic electrolyte thin films.

Science.gov (United States)

Park, Jun-Sik; Kim, Dug-Joong; Chung, Wan-Ho; Lim, Yonghyun; Kim, Hak-Sung; Kim, Young-Beom

2017-09-29

Here we report a photonic annealing process for yttria-stabilized zirconia films, which are one of the most well-known solid-state electrolytes for solid oxide fuel cells (SOFCs). Precursor films were coated using a wet-chemical method with a simple metal-organic precursor solution and directly annealed at standard pressure and temperature by two cycles of xenon flash lamp irradiation. The residual organics were almost completely decomposed in the first pre-annealing step, and the fluorite crystalline phases and good ionic conductivity were developed during the second annealing step. These films showed properties comparable to those of thermally annealed films. This process is much faster than conventional annealing processes (e.g. halogen furnaces); a few seconds compared to tens of hours, respectively. The significance of this work includes the treatment of solid-state electrolyte oxides for SOFCs and the demonstration of the feasibility of other oxide components for solid-state energy devices.

Artificial in-plane ordering of textured YBa2Cu3O(7-x) films deposited on polycrystalline yttria-stabilized zirconia substrates

Science.gov (United States)

Harshavardhan, K. S.; Rajeswari, M.; Hwang, D. M.; Chen, C. Y.; Sands, T. D.; Venkatesan, T.; Tkaczyk, J. E.; Lay, K. W.; Safari, A.; Johnson, L.

1992-12-01

Anisotropic surface texturing of the polycrystalline yttria-stabilized zirconia substrates, prior to YBa2Cu3O(7-x) film deposition, is shown to promote in-plane (basal plane) ordering of the film growth in addition to the c-axis texturing. The Jc's of the films in the weak-link-dominated low-field regime are enhanced considerably, and this result is attributed to the reduction of weak links resulting from a reduction in the number of in-plane large-angle grain boundaries.

Rheological studies of aqueous stabilised nano-zirconia particle suspensions

Directory of Open Access Journals (Sweden)

Asad Ullah Khan

2012-02-01

Full Text Available In the present investigation aqueous suspensions of nano- and colloidal range particles are stabilised by changing the ambient pH. Rheology is used to establish the stability of the suspensions and it is found that the rheology of the suspensions is strongly dependent on the pH values. The viscosity is highest close to the iso-electric point of the powders. At the iso-electric point the net surface charge on the powder particles is zero and is the cause of the high viscosity. Away from the iso-electric point, the particles are charged, giving rise to a double layer phenomenon and causing the reduction in viscosity. It is also found that increasing the solid contents of the suspensions reduces the pH region of low viscosity.

Arm-length stabilisation for interferometric gravitational-wave detectors using frequency-doubled auxiliary lasers

OpenAIRE

Mullavey, Adam J.; Slagmolen, Bram J. J.; Miller, John; Evans, Matthew; Fritschel, Peter; Sigg, Daniel; Waldman, Sam J.; Shaddock, Daniel A.; McClelland, David E.

2011-01-01

Residual motion of the arm cavity mirrors is expected to prove one of the principal impediments to systematic lock acquisition in advanced gravitational-wave interferometers. We present a technique which overcomes this problem by employing auxiliary lasers at twice the fundamental measurement frequency to pre-stabilise the arm cavities’ lengths. Applying this approach, we reduce the apparent length noise of a 1.3 m long, independently suspended Fabry-Perot cavity to 30 pm rms and successfully...

Band structure of TiO sub 2 -doped yttria-stabilized zirconia probed by soft-x-ray spectroscopy

CERN Document Server

Higuchi, T; Kobayashi, K; Yamaguchi, S; Fukushima, A; Shin, S

2003-01-01

The electronic structure of TiO sub 2 -doped yttria-stabilized zirconia (YSZ) has been studied by soft-X-ray emission spectroscopy (SXES) and X-ray absorption spectroscopy (XAS). The valence band is mainly composed of the O 2p state. The O 1s XAS spectrum exhibits the existence of the Ti 3d unoccupied state under the Zr 4d conduction band. The intensity of the Ti 3d unoccupied state increases with increasing TiO sub 2 concentration. The energy separation between the top of the valence band and the bottom of the Ti 3d unoccupied state is in accord with the energy gap, as expected from dc-polarization and total conductivity measurements. (author)

Design and Fabrication of Porous Yttria-Stabilized Zirconia Ceramics for Hot Gas Filtration Applications

Science.gov (United States)

Shahini, Shayan

Hot gas filtration has received growing attention in a variety of applications over the past few years. Yttria-stabilized zirconia (YSZ) is a promising candidate for such an application. In this study, we fabricated disk-type porous YSZ filters using the pore forming procedure, in which poly methyl methacrylate (PMMA) was used as the pore-forming agent. After fabricating the pellets, we characterized them to determine their potential for application as gas filters. We investigated the effect of sintering temperature, polymer particle size, and polymer-to-ceramic ratio on the porosity, pore size, gas permeability, and Vickers hardness of the sintered pellets. Furthermore, we designed two sets of experiments to investigate the robustness of the fabricated pellets--i.e., cyclic heating/cooling and high temperature exposure. This study ushers in a robust technique to fabricate such porous ceramics, which have the potential to be utilized in hot gas filtration.

Operational experience with a commercial plant for stabilisation Of radioactive sludge and other materials in the United Kingdom - 16042

International Nuclear Information System (INIS)

Hagan, M.; Cornell, R.M.; Riley, B.; Ware, B.

2009-01-01

In 2000, Nuvia Limited was contracted to design, build and commission a waste treatment plant (WETP) to stabilise the active sludge stored in the External Active Storage Tanks (EAST) at UKAEA Winfrith, UK. The sludge was generated during the operational period of the prototype Steam Generating Heavy Water Reactor (SGHWR), which is now in the process of being decommissioned. This work supports UKAEA's mission, which is to carry out environmental restoration of its nuclear sites and to put them to alternative uses wherever possible. Recently UKAEA has been reorganised and responsibility for the site lies with Research Sites Restoration Limited (RSRL) with funding provided by the Nuclear Decommissioning Authority (NDA). The process of stabilisation of the SGHWR sludge from the EAST tanks within 500 litre stainless steel drums in the Winfrith EAST Treatment Plant (WETP) using ordinary Portland cement (OPC) and blast furnace slag (BFS) is now almost complete. At this stage it was planned to decommission and demolish the WETP facilities but RSRL have introduced a further stabilisation project involving thorium metal waste ahead of the start of the planned decommissioning. As a result, the facilities are to be revised to provide for the encapsulation of bars of thorium metal within modified 500 litre drums together with a number of necessary changes to the plant control system. The cell line used for stabilisation consists of five operational cells separated by shield doors designed to maintain strict contamination control. There is a wet cell where the drums are filled with sludge and powder, a cell with stations for curing and grouting the drums, a cell for lidding, bolting and QA inspection, a maintenance and gamma monitoring cell and a buffer store to hold the completed drums. After completion, drums are moved in a shielded overpack to the Treated Radwaste Store located on a different part of the Winfrith site. In the revised cell line configuration the wet cell will

Dose reference levels in Spanish intraoral dental radiology: stabilisation of the incorporation of digital systems in dental clinical practices

International Nuclear Information System (INIS)

Alcaraz, M.; Velasco, F.; Olivares, A.; Velasco, E.; Canteras, M.

2016-01-01

A total of 34 044 official quality assurance reports in dental radiodiagnostic surgery from 16 regions of Spain, compiled from 2002 to 2014, were studied in order to determine the progress of diagnostic reference levels (DRLs) for obtaining diagnostic images under normal conditions for clinical practice in Spanish dental clinics. A DRL of 2.8 mGy was set in 2014, which represents a 41.7 % decrease compared with that of 2002 (4.8 mGy). Over the same time period, the mean dose fell by 55.2 %. However, over the last 3 y, the stabilisation of the mean dose administered to patients has been observed with only a 6.7 % reduction in DRLs, which corresponds to the stabilisation of dental radiodiagnostic surgery on replacing the use of radiographic film with digital imaging systems. (authors)

Recycling stabilised/solidified drill cuttings for forage production in acidic soils.

Science.gov (United States)

Kogbara, Reginald B; Dumkhana, Bernard B; Ayotamuno, Josiah M; Okparanma, Reuben N

2017-10-01

Stabilisation/solidification (S/S), which involves fixation and immobilisation of contaminants using cementitious materials, is one method of treating drill cuttings before final fate. This work considers reuse of stabilised/solidified drill cuttings for forage production in acidic soils. It sought to improve the sustainability of S/S technique through supplementation with the phytoremediation potential of plants, eliminate the need for landfill disposal and reduce soil acidity for better plant growth. Drill cuttings with an initial total petroleum hydrocarbon (TPH) concentration of 17,125 mg kg -1 and low concentrations of metals were treated with 5%, 10%, and 20% cement dosages. The treated drill cuttings were reused in granular form for growing a forage, elephant grass (Pennisetum purpureum), after mixing with uncontaminated soil. The grasses were also grown in uncontaminated soil. The phytoremediation and growth potential of the plants was assessed over a 12-week period. A mix ratio of one part drill cuttings to three parts uncontaminated soil was required for active plant growth. The phytoremediation ability of elephant grass (alongside abiotic losses) reduced the TPH level (up to 8795 mg kg -1 ) in the soil-treated-drill cuttings mixtures below regulatory (1000 mg kg -1 ) levels. There were also decreased concentrations of metals. The grass showed better heights and leaf lengths in soil containing drill cuttings treated with 5% cement dosage than in uncontaminated soil. The results suggest that recycling S/S treated drill cuttings for forage production may be a potential end use of the treated waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal cycling behaviour of lanthanum zirconate as EB-PVD thermal barrier coating

International Nuclear Information System (INIS)

Bobzin, K.; Lugscheider, E.; Bagcivan, N.

2006-01-01

Thermal cycling tests with two different EB-PVD thermal barrier coatings (TBC) were performed in a furnace cycle test. The results of these tests showed an increase of endurable cycle number when pyrochloric La 2 Zr 2 O 7 was used as TBC. 1865 cycles were reached with La 2 Zr 2 O 7 and 1380 cycles with 7 weigth-% yttria stabilised zirconia (YSZ) EB-PVD TBC. Additional investigation was made with scanning electron microscope (SEM) to investigate morphology and to determine chemical composition by electron dispersive x-ray spectroscopy (EDS) analysis. X-Ray diffraction was performed to analyze structural constitution of deposited coatings. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

COMBINATIONS OF BUFFER-STOCKS AND BUFFER-FUNDS FOR WOOL PRICE STABILISATION IN AUSTRALIA

OpenAIRE

Moir, Brian; Piggott, Roley R.

1991-01-01

In this paper a preliminary analysis is presented of a combined buffer-fund and buffer-stock as an alternative to a pure buffer-fund or a pure buffer stock for stabilising wool prices. The alternatives analysed are designed so that each provides the same prices to producers as did the Reserve Price Scheme over the period of analysis. Least-cost combinations of policy instruments are derived. The results show that there is considerable potential for cost savings to be made by combining buffer-...

A Scott bench with ergonomic thorax stabilisation pad improves body posture during preacher arm curl exercise.

Science.gov (United States)

Biscarini, Andrea; Benvenuti, Paolo; Busti, Daniele; Zanuso, Silvano

2016-05-01

We assessed whether the use of an ergonomic thorax stabilisation pad, during the preacher arm curl exercise, could significantly reduce the excessive shoulder protraction and thoracic kyphosis induced by the standard flat pad built into the existing preacher arm curl equipment. A 3D motion capture system and inclinometers were used to measure shoulder protraction and thoracic kyphosis in 15 subjects performing preacher arm curl with a plate-loaded machine provided with the standard flat pad. The same measures were repeated after replacing the flat pad with a new ergonomic pad, specifically designed to accommodate the thorax profile and improve body posture. Pad replacement significantly (p ergonomic pad may potentially allow a more effective training, prevent musculoskeletal discomfort and reduce the risk of injury. Practitioner summary: We have designed an ergonomic thorax stabilisation pad for the preacher arm curl exercise. The new ergonomic pad improves the poor posture conditions induced by the standard flat pad and may potentially allow a more effective training, prevent musculoskeletal discomfort, improve the breathing function and reduce the risk of injury.

Chemical vapor deposition of yttria stabilized zirconia in porous substrates

International Nuclear Information System (INIS)

Carolan, M.F.; Michaels, J.N.

1987-01-01

Electrochemical vapor deposition (EVD) of yttria stabilized zirconia (YSZ) is the preferred route to the production of thin films of YSZ on porous substrates. This process has been used in the construction of both fuel cells and steam electrolyzers. A critical aspect of the EVD process is an initial chemical vapor deposition phase in which the pores of a porous substrate are plugged by YSZ. In this process, water vapor and a mixture of gaseous zirconium chloride and yttrium chloride diffuse into the porous substrate from opposite sides and react to form YSZ and HCl ga. During the second stage of the process a continuous dense film of electrolyte is formed by a tarnishing-type process. Experimentally it is observed that the pores plug within a few pore diameters of the metal chloride face of the substrate. A kinetic rate expression that is first order in metal chloride but zero order in water is best able to explain this phenomenon. With this rate expression, the pores always plug near the metal chloride face. The model predicts less pore narrowing to occur as the ratio of the reaction rate to the diffusion rate of the metal chloride is increased. A kinetic rate expression that is first order in both water and metal chloride predicts that the pores plug much deeper in the substrate

Effects of varying oxygen partial pressure on molten silicon-ceramic substrate interactions

Science.gov (United States)

Ownby, D. P.; Barsoum, M. W.

1980-01-01

The silicon sessile drop contact angle was measured on hot pressed silicon nitride, silicon nitride coated on hot pressed silicon nitride, silicon carbon coated on graphite, and on Sialon to determine the degree to which silicon wets these substances. The post-sessile drop experiment samples were sectioned and photomicrographs were taken of the silicon-substrate interface to observe the degree of surface dissolution and degradation. Of these materials, silicon did not form a true sessile drop on the SiC on graphite due to infiltration of the silicon through the SiC coating, nor on the Sialon due to the formation of a more-or-less rigid coating on the liquid silicon. The most wetting was obtained on the coated Si3N4 with a value of 42 deg. The oxygen concentrations in a silicon ribbon furnace and in a sessile drop furnace were measured using the protable thoria-yttria solid solution electrolyte oxygen sensor. Oxygen partial pressures of 10 to the minus 7 power atm and 10 to the minus 8 power atm were obtained at the two facilities. These measurements are believed to represent nonequilibrium conditions.

Characterization of single crystal uranium-oxide thin films grown via reactive-gas magnetron sputtering on yttria-stabilized zirconia and sapphire

Energy Technology Data Exchange (ETDEWEB)

Strehle, Melissa M.; Heuser, Brent J., E-mail: bheuser@illinois.edu; Elbakhshwan, Mohamed S.; Han Xiaochun; Gennardo, David J.; Pappas, Harrison K.; Ju, Hyunsu

2012-06-30

The microstructure and valence states of three single crystal thin film systems, UO{sub 2} on (11{sup Macron }02) r-plane sapphire, UO{sub 2} on (001) yttria-stabilized zirconia, and U{sub 3}O{sub 8} on (11{sup Macron }02) r-plane sapphire, grown via reactive-gas magnetron sputtering are analyzed primarily with X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and ultraviolet photoelectron spectroscopy (UPS). XRD analysis indicates the growth of single crystal domains with varying degrees of mosaicity. XPS and UPS analyses yield U-4f, U-5f, O-1s, and O-2p electron binding energies consistent with reported bulk values. A change from p-type to n-type semiconductor behavior induced by preferential sputtering of oxygen during depth profile analysis was observed with both XPS and UPS. Trivalent cation impurities (Nd and Al) in UO{sub 2} lower the Fermi level, shifting the XPS spectral weight. This observation is consistent with hole-doping of a Mott-Hubbard insulator. The uranium oxide-(11{sup Macron }02) sapphire system is unstable with respect to Al interdiffusion across the film-substrate interface at elevated temperature. - Highlights: Black-Right-Pointing-Pointer Single crystal uranium-oxides grown on sapphire and yttria-stabilized zirconia. Black-Right-Pointing-Pointer Anion and cation valence states studied by photoelectron emission spectroscopy. Black-Right-Pointing-Pointer Trivalent Nd and Al impurities lower the Fermi level. Black-Right-Pointing-Pointer Uranium-oxide films on sapphire found to be unstable with respect to Al interdiffusion.

Electroactive mesoporous yttria stabilized zirconia containing platinum or nickel oxide nanoclusters: a new class of solid oxide fuel cell electrode materials

Energy Technology Data Exchange (ETDEWEB)

Mamak, M.; Coombs, N.; Ozin, G.A. [Toronto Univ., ON (Canada). Dept. of Chemistry

2001-02-01

The electroactivity of surfactant-templated mesoporous yttria stabilized zirconia, containing nanoclusters of platinum or nickel oxide, is explored by alternating current (AC) complex impedance spectroscopy. The observed oxygen ion and mixed oxygen ion-electron charge-transport behavior for these materials, compared to the sintered-densified non-porous crystalline versions, is ascribed to the unique integration of mesoporosity and nanocrystallinity within the binary and ternary solid solution microstructure. These attributes inspire interest in this new class of materials as candidates for the development of improved performance solid oxide fuel cell electrodes. (orig.)

Changes in X-ray photoelectron spectra of yttria-tetragonal zirconia polycrystal by ion sputtering

Energy Technology Data Exchange (ETDEWEB)

Watanabe, Eiko; Yoshinari, Masao [Tokyo Dental College, Oral Health Science Center, Tokyo, Chiyoda-ku (Japan)

2016-04-15

This paper reports changes in X-ray photoelectron spectroscopy spectra of yttria-tetragonal zirconia polycrystal (Y-TZP) brought about by Ar ion sputtering. The changes in the core-level spectra of Y-TZP suggest that preferential sputtering of oxygen occurred. A new peak was observed near 0 eV binding energy accompanied with changes in the core-level spectra by the sputtering. After 18 h in a high vacuum following the sputtering, the spectra changed by the sputtering were returned to their original shapes. In contrast, the color of Y-TZP was changed from white to pale brown by X-ray irradiation and was changed from pale brown to dark gray by ion sputtering. However, when the new peak near 0 eV decreased after 18 h, no color change was observed. Therefore, it is thought that the new peak was mainly derived from electrons trapped in various kinds of oxygen vacancies created by the sputtering in other than color centers. (orig.)

Stabilisation of ballooning modes in torsatrons with an externally applied toroidal current

International Nuclear Information System (INIS)

Cooper, W.A.

1996-01-01

It has been found that ideal ballooning modes can impose very restrictive volume average β limits in torsatrons much below the typical values close to 5% that are required to be economically realisable as reactor systems and it has been shown that externally applied toroidal currents that are peaked can destabilise the Mercier criterion in this type of configuration. We will show here that if the applied currents are hollow, they can stabilise the ballooning modes without triggering Mercier instabilities and as a result raise the limiting β* from 2% to 5%. (author) 3 figs., 10 refs

Structure of yttria stabilized zirconia beads produced by gel supported precipitation

International Nuclear Information System (INIS)

Walter, M.; Somers, J.; Fernandez, A.; Specht, Eliot D.; Hunn, John D.; Boulet, P.; Denecke, M. A.; Gobel, C.

2007-01-01

Yttria stabilized zirconia (YSZ) is one of the inert matrix candidates selected for investigation as host matrix for minor actinide (MA) transmutation. The structural properties of (Zr0.84, Y0.16)O1.92 beads prepared by a sol-gel method for MA infiltration, are characterized as calcined (850 C) and sintered (1,600 C) beads. The calcined YSZ beads are fine-grained and homogenous over the entire sphere and are surrounded by a uniform outer layer of approximately 30 (micro)m thickness. After sintering at 1,600 C, the beads are compacted to 51% of their initial volume and exhibit a granular structure. The thermal expansion is nearly linear for the calcined material, but shows a parabolic behavior for the sintered (1,400 C) beads. In addition, the thermal expansion of calcined material is 20-25% less than after sintering. During heating up to 1,400 C, two processes can be distinguished. The first occurs between 900 and 1,000 C and is related to an increase in unit cell order. The second process involves grain-growth of the less crystalline calcined material between 1,100 and 1,300 C. These results have implications for preparation of YSZ and its use as an inert MA transmutation matrix

Atomic structure and composition of the yttria-stabilized zirconia (111) surface.

Science.gov (United States)

Vonk, Vedran; Khorshidi, Navid; Stierle, Andreas; Dosch, Helmut

2013-06-01

Anomalous and nonanomalous surface X-ray diffraction is used to investigate the atomic structure and composition of the yttria-stabilized zirconia (YSZ)(111) surface. By simulation it is shown that the method is sensitive to Y surface segregation, but that the data must contain high enough Fourier components in order to distinguish between different models describing Y/Zr disorder. Data were collected at room temperature after two different annealing procedures. First by applying oxidative conditions at 10 - 5  mbar O 2 and 700 K to the as-received samples, where we find that about 30% of the surface is covered by oxide islands, which are depleted in Y as compared with the bulk. After annealing in ultrahigh vacuum at 1270 K the island morphology of the surface remains unchanged but the islands and the first near surface layer get significantly enriched in Y. Furthermore, the observation of Zr and oxygen vacancies implies the formation of a porous surface region. Our findings have important implications for the use of YSZ as solid oxide fuel cell electrode material where yttrium atoms and zirconium vacancies can act as reactive centers, as well as for the use of YSZ as substrate material for thin film and nanoparticle growth where defects control the nucleation process.

Environmental Controls and Eco-geomorphic Interactions of the Barchan-to-parabolic Dune Stabilisation and the Parabolic-to-barchan Dune Reactivation

Science.gov (United States)

Yan, Na; Baas, Andreas

2015-04-01

Parabolic dunes are one of a few common aeolian landforms which are highly controlled by eco-geomorphic interactions. Parabolic dunes, on the one hand, can be developed from highly mobile dune landforms, barchans for instance, in an ameliorated vegetation condition; or on the other hand, they can be reactivated and transformed back into mobile dunes due to vegetation deterioration. The fundamental mechanisms and eco-geomorphic interactions controlling both dune transformations remain poorly understood. To bridge the gap between complex processes involved in dune transformations on a relatively long temporal scale and real world monitoring records on a very limited temporal scale, this research has extended the DECAL model to incorporate 'dynamic' growth functions and the different 'growth' of perennial shrubs between growing and non-growing seasons, informed by field measurements and remote sensing analysis, to explore environmental controls and eco-geomorphic interactions of both types of dune transformation. A non-dimensional 'dune stabilising index' is proposed to capture the interactions between environmental controls (i.e. the capabilities of vegetation to withstand wind erosion and sand burial, the sandy substratum thickness, the height of the initial dune, and the sand transport potential), and establish the linkage between these controls and the geometry of a stabilising dune. An example demonstrates how to use the power-law relationship between the dune stabilising index and the normalised migration distance to assist in extrapolating the historical trajectories of transforming dunes. The modelling results also show that a slight increase in vegetation cover of an initial parabolic dune can significantly increase the reactivation threshold of climatic impact (both drought stress and wind strength) required to reactivate a stabilising parabolic dune into a barchan. Four eco-geomorphic interaction zones that govern a barchan-to-parabolic dune transformation

Atomistic modeling of La3+ doping segregation effect on nanocrystalline yttria-stabilized zirconia.

Science.gov (United States)

Zhang, Shenli; Sha, Haoyan; Castro, Ricardo H R; Faller, Roland

2018-05-16

The effect of La3+ doping on the structure and ionic conductivity change in nanocrystalline yttria-stabilized zirconia (YSZ) was studied using a combination of Monte Carlo and molecular dynamics simulations. The simulation revealed the segregation of La3+ at eight tilt grain boundary (GB) structures and predicted an average grain boundary (GB) energy decrease of 0.25 J m-2, which is close to the experimental values reported in the literature. Cation stabilization was found to be the main reason for the GB energy decrease, and energy fluctuations near the grain boundary are smoothed out with La3+ segregation. Both dynamic and energetic analysis on the Σ13(510)/[001] GB structure revealed La3+ doping hinders O2- diffusion in the GB region, where the diffusion coefficient monotonically decreases with increasing La3+ doping concentration. The effect was attributed to the increase in the site-dependent migration barriers for O2- hopping caused by segregated La3+, which also leads to anisotropic diffusion at the GB.

Characterization on the electrophoretic deposition of the 8 mol% yttria-stabilized zirconia nanocrystallites prepared by a sol-gel process

Energy Technology Data Exchange (ETDEWEB)

Lee, Y.-H. [Department of Materials Science and Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Kuo, C.-W. [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Shih, C.-J. [Faculty of Fragrance and Cosmetics, Kaohsiung Medical University, 100 Shi-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Hung, I-M. [Department of Materials Science and Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Fung, K.-Z. [Department of Materials Science and Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Wen, S.-B. [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Wang, M.-C. [Faculty of Fragrance and Cosmetics, Kaohsiung Medical University, 100 Shi-Chuan 1st Road, Kaohsiung 807, Taiwan (China)]. E-mail: cjshih@kmu.edu.tw

2007-02-15

An 8 mol% yttria-stabilized zirconia (8YSZ) films are electrophoretically deposited on the La{sub 0.8}Sr{sub 0.2}MnO{sub 3} substrate using 8YSZ nanocrystallites prepared by a sol-gel process. Effects of liquid suspension on the particle zeta potential and degree of agglomeration at different pH values are investigated. When the pH value deviates from the point of zero charge (PZC), the adsorption of protons on particle surfaces cause higher zeta potential and well-dispersed suspension. The optimal values of the iodine concentration, applied voltage and deposition time for the electrophoretic deposition of 8YSZ films are also found.

The use of biogas plant fermentation residue for the stabilisation of toxic metals in agricultural soils

Science.gov (United States)

Geršl, Milan; Šotnar, Martin; Mareček, Jan; Vítěz, Tomáš; Koutný, Tomáš; Kleinová, Jana

2015-04-01

Our department has been paying attention to different methods of soil decontamination, including the in situ stabilisation. Possible reagents to control the toxic metals mobility in soils include a fermentation residue (FR) from a biogas plant. Referred to as digestate, it is a product of anaerobic decomposition taking place in such facilities. The fermentation residue is applied to soils as a fertiliser. A new way of its use is the in situ stabilisation of toxic metals in soils. Testing the stabilisation of toxic metals made use of real soil samples sourced from five agriculturally used areas of the Czech Republic with 3 soil samples taken from sites contaminated with Cu, Pb and Zn and 2 samples collected at sites of natural occurrence of Cu, Pb and Zn ores. All the samples were analysed using the sequential extraction procedure (BCR) (determine the type of Cu, Pb and Zn bonds). Stabilisation of toxic metals was tested in five soil samples by adding reagents as follows: dolomite, slaked lime, goethite, compost and fermentation residue. A single reagent was added at three different concentrations. In the wet state with the added reagents, the samples were left for seven days, shaken twice per day. After seven days, metal extraction was carried out: samples of 10 g soil were shaken for 2 h in a solution of 0.1M NH4NO3 at a 1:2.5 (g.ml-1), centrifuged for 15 min at 5,000 rpm and then filtered through PTFE 0.45 μm mesh filters. The extracts were analysed by ICP-OES. Copper The best reduction of Cu concentration in the extract was obtained at each of the tested sites by adding dolomite (10 g soil + 0.3 g dolomite). The concentration of Cu in the leachate decreased to 2.1-18.4% compare with the leachate without addition. Similar results were also shown for the addition of fermentation residue (10 g soil + 1 g FR). The Cu concentration in the leachate decreased to 16.7-26.8% compared with the leachate without addition. Lead The best results were achieved by adding

Composite cathode based on yttria stabilized bismuth oxide for low-temperature solid oxide fuel cells

International Nuclear Information System (INIS)

Xia Changrong; Zhang Yuelan; Liu Meilin

2003-01-01

Composites consisting of silver and yttria stabilized bismuth oxide (YSB) have been investigated as cathodes for low-temperature honeycomb solid oxide fuel cells with stabilized zirconia as electrolytes. At 600 deg. C, the interfacial polarization resistances of a porous YSB-Ag cathode is about 0.3 Ω cm 2 , more than one order of magnitude smaller than those of other reported cathodes on stabilized zirconia. For example, the interfacial resistances of a traditional YSZ-lanthanum maganites composite cathode is about 11.4 Ω cm 2 at 600 deg. C. Impedance analysis indicated that the performance of an YSB-Ag composite cathode fired at 850 deg. C for 2 h is severely limited by gas transport due to insufficient porosity. The high performance of the YSB-Ag cathodes is very encouraging for developing honeycomb fuel cells to be operated at temperatures below 600 deg. C

Hydraulic retention time on vinasse stabilisation with limestone in the acidogenic phase of anaerobic digestion

Directory of Open Access Journals (Sweden)

Ismael Plácido Tomielis

Full Text Available ABSTRACT: The main problem in anaerobic digestion of low-protein residues is the instability caused acidity. The use of limestone at the same time as a neutralizing agent and support material is innovative because stones wear allows the slow release of the calcium carbonate thereby eliminating dispersers. Free calcium content in the system was measured in two plug flow reactors filled with vinasse at initial pH of 4.50. The proportion of 1.8 tonnes of limestone per m³ of vinasse was evaluated at the Hydraulic Retention Times (HRT of 24, 48, 72, 96 and 120 hours, allowing stabilisation at 96 hours. The ratio of Volatile Acids/Total Alkalinity (VA/TA ranged from 0.2 to 0.4 and the pH reached 7.0, at the HRT of 120 hours. Increasing the HRT also increased the volatile total solids (VTS and fixed total solids (TFS in a similar profile to the measured free calcium content, but calcium remained at the appropriate level of 100 to 250mg l-1. The proportion of limestone/vinasse was adequate to ensure stabilisation, but it is not recommended to reduce the HRT below 96 hours due to the risk of compromising the stability of the anaerobic system.

Sludge digestion instead of aerobic stabilisation - a cost benefit analysis based on experiences in Germany.

Science.gov (United States)

Gretzschel, Oliver; Schmitt, Theo G; Hansen, Joachim; Siekmann, Klaus; Jakob, Jürgen

2014-01-01

As a consequence of a worldwide increase of energy costs, the efficient use of sewage sludge as a renewable energy resource must be considered, even for smaller wastewater treatment plants (WWTPs) with design capacities between 10,000 and 50,000 population equivalent (PE). To find the lower limit for an economical conversion of an aerobic stabilisation plant into an anaerobic stabilisation plant, we derived cost functions for specific capital costs and operating cost savings. With these tools, it is possible to evaluate if it would be promising to further investigate refitting aerobic plants into plants that produce biogas. By comparing capital costs with operation cost savings, a break-even point for process conversion could be determined. The break-even point varies depending on project specific constraints and assumptions related to future energy and operation costs and variable interest rates. A 5% increase of energy and operation costs leads to a cost efficient conversion for plants above 7,500 PE. A conversion of WWTPs results in different positive effects on energy generation and plant operations: increased efficiency, energy savings, and on-site renewable power generation by digester gas which can be used in the plant. Also, the optimisation of energy efficiency results in a reduction of primary energy consumption.

? and ? nonquadratic stabilisation of discrete-time Takagi-Sugeno systems based on multi-instant fuzzy Lyapunov functions

Science.gov (United States)

Tognetti, Eduardo S.; Oliveira, Ricardo C. L. F.; Peres, Pedro L. D.

2015-01-01

The problem of state feedback control design for discrete-time Takagi-Sugeno (TS) (T-S) fuzzy systems is investigated in this paper. A Lyapunov function, which is quadratic in the state and presents a multi-polynomial dependence on the fuzzy weighting functions at the current and past instants of time, is proposed.This function contains, as particular cases, other previous Lyapunov functions already used in the literature, being able to provide less conservative conditions of control design for TS fuzzy systems. The structure of the proposed Lyapunov function also motivates the design of a new stabilising compensator for Takagi-Sugeno fuzzy systems. The main novelty of the proposed state feedback control law is that the gain is composed of matrices with multi-polynomial dependence on the fuzzy weighting functions at a set of past instants of time, including the current one. The conditions for the existence of a stabilising state feedback control law that minimises an upper bound to the ? or ? norms are given in terms of linear matrix inequalities. Numerical examples show that the approach can be less conservative and more efficient than other methods available in the literature.

Treatment of post-orthodontic white spot lesions with casein phosphopeptide-stabilised amorphous calcium phosphate

DEFF Research Database (Denmark)

Bröchner, Ann; Christensen, Carsten; Kristensen, Bjarne

2010-01-01

This study aims to investigate the effect of topical applications of 10% casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) on white spot lesions (WSL) detected after treatment with fixed orthodontic appliances. Sixty healthy adolescents with >/=1 clinically visible WSL at debonding were...... findings were largely reflected by the clinical scores. No side effects were reported. Topical treatment of white spot lesions after debonding of orthodontic appliances with a casein phosphopeptide-stabilised amorphous calcium phosphate agent resulted in significantly reduced fluorescence and a reduced...

Potential assessment of using fly ash as a binding agent for stabilization and solidification of dredged material; Potentialbedoemning av flygaskor som bindemedelskomponent foer stabilisering och solidifiering (s/s) av muddermassor

Energy Technology Data Exchange (ETDEWEB)

Wilhelmsson, Anna; Holm, Goeran; Lagerlund, Johan; Maijala, Aino; Macsik, Josef

2010-04-15

Over the next few years, about 200 000-800 000 m3 of contaminated sediments, with a muddy, slimy texture, high water ratio and low strength, shall be dredged annually in the development of ports and maintenance dredging of navigable waterways. Dumping at sea is limited since the dredged materials are contaminated. Land disposal requires transports and land area and is thus high in costs. In the construction of new port areas, large volumes of crushed rock, etc. are normally used as construction filling materials. These materials can be replaced by stabilised and solidified dredged materials, with modified geotechnical properties. The method of stabilising/solidifying (s/s) contaminated dredged materials has been used internationally for a long period of time, and, in more recent years, also in the Nordic countries. In Sweden, for instance, the Port of Gaevle and the Port of Oxeloesund have received permissions to reuse s/s-treated contaminated dredged materials in the port structures. Reuse of the stabilised/solidified masses in a geotechnical structure is supported by the new Framework Directive (2008/98/EC) on waste where great emphasis is placed on recycling. Within the project, fly ashes were inventoried with respect to suitability and availability. Five fly ashes, both individual fly ashes and mixtures of different fly ashes, were investigated in the laboratory as a binder component in a binder mix consisting of 50% cement, 20% Merit 5000 and 30% fly ash. Sediment from the Port of Gaevle were stabilised with a binder mixture amount of 150 kg/m3. Produced samples were examined in terms of strength, permeability and leaching. An assessment of the fly ashes' potential was performed based on technological, environmental and economical aspects, as well as market demand and the acceptance of stabilised and solidified dredged materials as construction material. The results show that fly ash, together in a binder mixture with construction cement and slag cement

Drive beam stabilisation in the CLIC Test Facility 3

Science.gov (United States)

Malina, L.; Corsini, R.; Persson, T.; Skowroński, P. K.; Adli, E.

2018-06-01

The proposed Compact Linear Collider (CLIC) uses a high intensity, low energy drive beam to produce the RF power needed to accelerate a lower intensity main beam with 100 MV/m gradient. This scheme puts stringent requirements on drive beam stability in terms of phase, energy and current. The consequent experimental work was carried out in CLIC Test Facility CTF3. In this paper, we present a novel analysis technique in accelerator physics to find beam drifts and their sources in the vast amount of the continuously gathered signals. The instability sources are identified and adequately mitigated either by hardware improvements or by implementation and commissioning of various feedbacks, mostly beam-based. The resulting drive beam stability is of 0.2°@ 3 GHz in phase, 0.08% in relative beam energy and about 0.2% beam current. Finally, we propose a stabilisation concept for CLIC to guarantee the main beam stability.

Simple intervention to reduce mosquito breeding in waste stabilisation ponds

DEFF Research Database (Denmark)

Ensink, Jeroen H J; Mukhtar, Muhammad; van der Hoek, Wim

2007-01-01

Waste stabilisation ponds (WSP) are the preferred method for treatment of urban wastewater in low-income countries but, especially in arid regions, the pond systems can be important breeding sites for mosquitoes of medical importance. In a WSP system in Faisalabad, Pakistan, we assessed the impact...... of simple environmental interventions on mosquito occurrence and abundance. Reducing the amount of floating matter in the ponds, eliminating emergent vegetation and repairing cracks in the cement structure reduced the number of mosquito-positive samples in the intervention ponds to almost zero, whereas...... the control ponds had a significant number of positive samples. This suggests that a combination of simple low-cost interventions is a feasible environmental management strategy for vector control in WSP systems that are located in areas where medically important mosquitoes may breed in the shallow ponds....

Lattice location of platinum ions implanted into single crystal zirconia and their annealing behaviour

Energy Technology Data Exchange (ETDEWEB)

Cao, D X [Royal Melbourne Inst. of Tech., VIC (Australia); Sood, D K [Academia Sinica, Shanghai, SH (China). Shanghai Inst. of Nuclear Research; Brown, I G [Lawrence Berkeley Lab., CA (United States)

1994-12-31

Single crystal samples of (100) oriented cubic zirconia stabilised with 9.5 mol % yttria were implanted with platinum ions, using a metal vapour vacuum arc (MEVVA) high current ion implanter, to a nominal dose of 1x10{sup 17} ions/cm{sup 2}. The implanted samples were annealed isothermally in air ambient at 1200 deg C, from 1-24 hours. Rutherford Backscattering Spectrometry and Channeling (RBSC) of 2 MeV He ions are employed to determine depth distributions of ion damage, Pt ions and substitutionality of Pt ions before and after annealing. The damage behaviour, Pt migration and lattice location are discussed in terms of metastable phase formation and solid solubility considerations. 7 refs., 3 figs.

Lattice location of platinum ions implanted into single crystal zirconia and their annealing behaviour

Energy Technology Data Exchange (ETDEWEB)

Cao, D.X. [Royal Melbourne Inst. of Tech., VIC (Australia); Sood, D.K. [Academia Sinica, Shanghai, SH (China). Shanghai Inst. of Nuclear Research; Brown, I.G. [Lawrence Berkeley Lab., CA (United States)

1993-12-31

Single crystal samples of (100) oriented cubic zirconia stabilised with 9.5 mol % yttria were implanted with platinum ions, using a metal vapour vacuum arc (MEVVA) high current ion implanter, to a nominal dose of 1x10{sup 17} ions/cm{sup 2}. The implanted samples were annealed isothermally in air ambient at 1200 deg C, from 1-24 hours. Rutherford Backscattering Spectrometry and Channeling (RBSC) of 2 MeV He ions are employed to determine depth distributions of ion damage, Pt ions and substitutionality of Pt ions before and after annealing. The damage behaviour, Pt migration and lattice location are discussed in terms of metastable phase formation and solid solubility considerations. 7 refs., 3 figs.

Optical characterization of Pr3+-doped yttria-stabilized zirconia single crystals

International Nuclear Information System (INIS)

Savoini, B.; Munoz Santiuste, J.E.; Gonzalez, R.

1997-01-01

The optical absorption and fluorescence of Pr 3+ ions in yttria-stabilized zirconia single crystals are investigated. Fluorescence emissions from the 1 D 2 level are clearly dominant and low intensity emission lines from the 3 P 0 and 1 G 4 states are also observed. Analysis with the Judd-Ofelt theory of the absorption intensities has been made assuming that only ∼40% of the praseodymium ions contribute to the optical absorption bands. Quantum efficiency values of η( 3 P 0 )∼0.2 and η( 1 D 2 )∼ 1 are obtained at room temperature. 1 D 2 fluorescence quenching has been observed in heavily-doped samples due to cross relaxation processes among neighboring Pr 3+ ions. Analysis using the Inokuti-Hirayama model shows that electric dipole-dipole interactions are mainly responsible for the quenching effect. Pr 3+ ions are present in seven and sixfold configurations with a statistical distribution. The energy position of the 4f5d configuration is very different for each center. The fluorescence dynamics is explained by a mechanism involving thermally assisted population of the 3 P 1,2 + 1 I 6 upper levels and fast relaxation to the 1 D 2 level via states of the excited 4f5d configuration. copyright 1997 The American Physical Society

Effect of highly dispersed yttria addition on thermal stability of hydroxyapatite

International Nuclear Information System (INIS)

Parente, P.; Savoini, B.; Ferrari, B.; Monge, M.A.; Pareja, R.; Sanchez-Herencia, A.J.

2013-01-01

The capability of the colloidal method to produce yttria (Y 2 O 3 ) dispersed hydroxyapatite (HA) has been investigated as an alternative method to the conventional method of mechanical mixing and sintering for developing HA-based materials that could exhibit controllable and enhanced functional properties. A water based colloidal route to produce HA materials with highly dispersed Y 2 O 3 has been applied, and the effect of 10 wt.% Y 2 O 3 addition to HA investigated by thermal analysis, X-ray diffraction and Fourier transform infrared spectroscopy. These measurements evidence a remarkable effect of this Y 2 O 3 addition on decomposition mechanisms of synthetic HA. Results show that incorporation of Y 2 O 3 as dispersed second phase is beneficial because it hinders the decomposition mechanisms of HA into calcium phosphates. This retardation will allow the control of the sintering conditions for developing HA implants with improved properties. Besides, substitution of Ca 2+ with Y 3+ ions appears to promote the formation of OH − vacancies, which could improve the conductive properties of HA favorable to osseointegration. - Highlights: ► We reveal the influence of Y 2 O 3 on thermal stability of hydroxyapatite. ► Incorporation of Y 2 O 3 delays decomposition of hydroxyapatite to calcium phosphates. ► Addition of Y 2 O 3 enables sintering conditions more favorable to the densification.

CLAY SOIL STABILISATION USING POWDERED GLASS

Directory of Open Access Journals (Sweden)

J. OLUFOWOBI

2014-10-01

Full Text Available This paper assesses the stabilizing effect of powdered glass on clay soil. Broken waste glass was collected and ground into powder form suitable for addition to the clay soil in varying proportions namely 1%, 2%, 5%, 10% and 15% along with 15% cement (base by weight of the soil sample throughout. Consequently, the moisture content, specific gravity, particle size distribution and Atterberg limits tests were carried out to classify the soil using the ASSHTO classification system. Based on the results, the soil sample obtained corresponded to Group A-6 soils identified as ‘fair to poor’ soil type in terms of use as drainage and subgrade material. This justified stabilisation of the soil. Thereafter, compaction, California bearing ratio (CBR and direct shear tests were carried out on the soil with and without the addition of the powdered glass. The results showed improvement in the maximum dry density values on addition of the powdered glass and with corresponding gradual increase up to 5% glass powder content after which it started to decrease at 10% and 15% powdered glass content. The highest CBR values of 14.90% and 112.91% were obtained at 5% glass powder content and 5mm penetration for both the unsoaked and soaked treated samples respectively. The maximum cohesion and angle of internal friction values of 17.0 and 15.0 respectively were obtained at 10% glass powder content.

Initial Bacterial Adhesion on Different Yttria-Stabilized Tetragonal Zirconia Implant Surfaces in Vitro

Directory of Open Access Journals (Sweden)

Lamprini Karygianni

2013-12-01

Full Text Available Bacterial adhesion to implant biomaterials constitutes a virulence factor leading to biofilm formation, infection and treatment failure. The aim of this study was to examine the initial bacterial adhesion on different implant materials in vitro. Four implant biomaterials were incubated with Enterococcus faecalis, Staphylococcus aureus and Candida albicans for 2 h: 3 mol % yttria-stabilized tetragonal zirconia polycrystal surface (B1a, B1a with zirconium oxide (ZrO2 coating (B2a, B1a with zirconia-based composite coating (B1b and B1a with zirconia-based composite and ZrO2 coatings (B2b. Bovine enamel slabs (BES served as control. The adherent microorganisms were quantified and visualized using scanning electron microscopy (SEM; DAPI and live/dead staining. The lowest bacterial count of E. faecalis was detected on BES and the highest on B1a. The fewest vital C. albicans strains (42.22% were detected on B2a surfaces, while most E. faecalis and S. aureus strains (approximately 80% were vital overall. Compared to BES; coated and uncoated zirconia substrata exhibited no anti-adhesive properties. Further improvement of the material surface characteristics is essential.

Color center annealing and ageing in electron and ion-irradiated yttria-stabilized zirconia

International Nuclear Information System (INIS)

Costantini, Jean-Marc; Beuneu, Francois

2005-01-01

We have used X-band electron paramagnetic resonance (EPR) measurements at room-temperature (RT) to study the thermal annealing and RT ageing of color centers induced in yttria-stabilized zirconia (YSZ), i.e. ZrO 2 :Y with 9.5 mol% Y 2 O 3 , by swift electron and ion-irradiations. YSZ single crystals with the orientation were irradiated with 2.5 MeV electrons, and implanted with 100 MeV 13 C ions. Electron and ion beams produce the same two color centers, namely an F + -type center (singly ionized oxygen vacancy) and the so-called T-center (Zr 3+ in a trigonal oxygen local environment) which is also produced by X-ray irradiations. Isochronal annealing was performed in air up to 973 K. For both electron and ion irradiations, the defect densities are plotted versus temperature or time at various fluences. The influence of a thermal treatment at 1373 K of the YSZ single crystals under vacuum prior to the irradiations was also investigated. In these reduced samples, color centers are found to be more stable than in as-received samples. Two kinds of recovery processes are observed depending on fluence and heat treatment

Thermal decomposition of phase-stabilised ammonium nitrate (PSAM), HTPB based propellants. The effect of iron(III)oxide burning-rate catalyst

NARCIS (Netherlands)

Carvalheira, P.; Gadiot, G.M.H.J.L.; Klerk, W.P.C. de

1995-01-01

Phase-stabilised ammonium nitrate (PSAN) and hydroxyl-terminated polybutadiene (HTPB) are the main ingredients of propellants used with success in some pyrotechnic igniter components of the VULCAIN liquid rocket engine for the ARIANE 5. Small amounts of selected additives play an important role in

Influence of testing conditions on the performance and durability of polymer stabilisers in thermal oxidation

Czech Academy of Sciences Publication Activity Database

Pospíšil, Jan; Horák, Zdeněk; Pilař, Jan; Billingham, N. C.; Zweifel, H.; Nešpůrek, Stanislav

2003-01-01

Roč. 82, č. 2 (2003), s. 145-162 ISSN 0141-3910. [International conference on Polymer Modification, Degradation and Stabilisation. Budapest, 30.06.2002-04.07.2002] R&D Projects: GA MŠk ME 543; GA MŠk ME 558; GA ČR GA203/02/1243; GA AV ČR IBS4050009 Institutional research plan: CEZ:AV0Z4050913 Keywords : accelerated tests * long-term heat ageing * oven ageing Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.405, year: 2003

Robust PID based power system stabiliser: Design and real-time implementation

Energy Technology Data Exchange (ETDEWEB)

Bevrani, Hassan [Department of Electrical and Computer Eng., University of Kurdistan, Sanandaj (Iran, Islamic Republic of); Hiyama, Takashi [Department of Electrical and Computer Eng., Kumamoto University, Kumamoto (Japan); Bevrani, Hossein [Department of Statistics, University of Tabriz, Tabriz (Iran, Islamic Republic of)

2011-02-15

This paper addresses a new robust control strategy to synthesis of robust proportional-integral-derivative (PID) based power system stabilisers (PSS). The PID based PSS design problem is reduced to find an optimal gain vector via an H{infinity} static output feedback control (H{infinity}-SOF) technique, and the solution is easily carried out using a developed iterative linear matrix inequalities algorithm. To illustrate the developed approach, a real-time experiment has been performed for a longitudinal four-machine infinite-bus system using the Analog Power System Simulator at the Research Laboratory of the Kyushu Electric Power Company. The results of the proposed control strategy are compared with full-order H{infinity} and conventional PSS designs. The robust PSS is shown to maintain the robust performance and minimise the effect of disturbances properly. (author)

On moduli stabilisation and de Sitter vacua in MSSM heterotic orbifolds

Energy Technology Data Exchange (ETDEWEB)

Parameswaran, Susha L. [Uppsala Univ. (Sweden). Dept. of Physics and Astronomy; Ramos-Sanchez, Saul [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Zavala, Ivonne [Bonn Univ. (Germany). Bethe Center for Theoretical Physics and Physikalisches Inst.

2010-09-15

We study the problem of moduli stabilisation in explicit heterotic orbifold compactifications, whose spectra contain the MSSM plus some vector-like exotics that can be decoupled. Considering all the bulk moduli, we obtain the 4D low energy effective action for the compactification, which has contributions from various, computable, perturbative and non-perturbative effects. Hidden sector gaugino condensation and string worldsheet instantons result in a combination of racetrack, KKLT and cusp-form contributions to the superpotential, which lift all the bulk moduli directions. We point out the properties observed in our concrete models, which tend to be missed when only ''generic'' features of a model are assumed. We search for interesting vacua and find several de Sitter solutions, but so far, they all turn out to be unstable. (orig.)

Laser surface modification of Yttria Stabilized Zirconia (YSZ) thermal barrier coating on AISI H13 tool steel substrate

Science.gov (United States)

Reza, M. S.; Aqida, S. N.; Ismail, I.

2018-03-01

This paper presents laser surface modification of plasma sprayed yttria stabilized zirconia (YSZ) coating to seal porosity defect. Laser surface modification on plasma sprayed YSZ was conducted using 300W JK300HPS Nd: YAG laser at different operating parameters. Parameters varied were laser power and pulse frequency with constant residence time. The coating thickness was measured using IM7000 inverted optical microscope and surface roughness was analysed using two-dimensional Mitutoyo Surface Roughness Tester. Surface roughness of laser surface modification of YSZ H-13 tool steel decreased significantly with increasing laser power and decreasing pulse frequency. The re-melted YSZ coating showed higher hardness properties compared to as-sprayed coating surface. These findings were significant to enhance thermal barrier coating surface integrity for dies in semi-solid processing.

Finite-time stabilisation of a class of switched nonlinear systems with state constraints

Science.gov (United States)

Huang, Shipei; Xiang, Zhengrong

2018-06-01

This paper investigates the finite-time stabilisation for a class of switched nonlinear systems with state constraints. Some power orders of the system are allowed to be ratios of positive even integers over odd integers. A Barrier Lyapunov function is introduced to guarantee that the state constraint is not violated at any time. Using the convex combination method and a recursive design approach, a state-dependent switching law and state feedback controllers of individual subsystems are constructed such that the closed-loop system is finite-time stable without violation of the state constraint. Two examples are provided to show the effectiveness of the proposed method.

Effects of artificial aging conditions on yttria-stabilized zirconia implant abutments.

Science.gov (United States)

Basílio, Mariana de Almeida; Cardoso, Kátia Vieira; Antonio, Selma Gutierrez; Rizkalla, Amin Sami; Santos Junior, Gildo Coelho; Arioli Filho, João Neudenir

2016-08-01

Most ceramic abutments are fabricated from yttria-stabilized tetragonal zirconia (Y-TZP). However, Y-TZP undergoes hydrothermal degradation, a process that is not well understood. The purpose of this in vitro study was to assess the effects of artificial aging conditions on the fracture load, phase stability, and surface microstructure of a Y-TZP abutment. Thirty-two prefabricated Y-TZP abutments were screwed and tightened down to external hexagon implants and divided into 4 groups (n = 8): C, control; MC, mechanical cycling (1×10(6) cycles; 10 Hz); AUT, autoclaving (134°C; 5 hours; 0.2 MPa); and TC, thermal cycling (10(4) cycles; 5°/55°C). A single-load-to-fracture test was performed at a crosshead speed of 0.5 mm/min to assess the assembly's resistance to fracture (ISO Norm 14801). X-ray diffraction (XRD) analysis was applied to observe and quantify the tetragonal-monoclinic (t-m) phase transformation. Representative abutments were examined with high-resolution scanning electron microscopy (SEM) to observe the surface characteristics of the abutments. Load-to-fracture test results (N) were compared by ANOVA and Tukey test (α=.05). XRD measurements revealed the monoclinic phase in some abutments after each aging condition. All the aging conditions reduced the fracture load significantly (Paging conditions. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Influence of nature of the substrate in the deposition of yttria-stabilized zirconia by spray pyrolysis

International Nuclear Information System (INIS)

Halmenschlager, C.M.; Malfatti, C.F.; Bergmann, C.P.; Neagu, R.

2012-01-01

Spray pyrolysis technique consist in spraying a precursor solution on a heated substrate. In the last few decades this process has attracted much attention because of its versatility. Controlling the parameters is possible to produce dense or porous film. Spray pyrolysis has been applied to obtain several materials such as electrodes or electrolytes for SOFC, semiconductors, materials for solar cells and so on. However, some behaviors such as Leidenfrost effect have been poorly considered and it may affect the coating quality. This work aims to evaluate the influence of the substrate and how Leidenfrost effect affects the coating by spray pyrolysis. To achieve this goal yttria-stabilized zirconia solutions made with different solvents were deposited on different substrates at different temperatures. These coatings were characterized by X-ray diffraction and scanning electron microscopy. The results show that there is a limit temperature which is related to properties of the solvent and the surface of the substrates where films are continuous. (author)

Significance of internal stresses for the martensitic transformation in yttria-stabilized tetragonal zirconia polycrystals during degradation

International Nuclear Information System (INIS)

Schmauder, S.; Schubert, H.

1986-01-01

Various aspects of the tetragonal (t) to monoclinic (m) transformation during degradation have been studied experimentally and theoretically in yttria-stabilized tetragonal zirconia polycrystals (Y-TZP), i.e., polycrystalline t-ZrO/sub 2/ containing Y/sub 2/O/sub 3/ in solution. Transmission electron microscopy (TEM) revealed that protruding grains at the surface of Y-TZP specimens do not transform under corrosive conditions (250 0 C, humid atmosphere) even after n annealing time of 168 h.) Eigenstresses due to anistropic thermal expansion in and around protruding and bulk grains have been calculated for Y-TZP containing 2 and 3 mol% Y/sub 2/O/sub 3/. The prominent role of these stresses on subsequent transformation nucleation during degradation is shown to agree qualitatively with an established free energy concept. The lack of complete transformation of m-ZrO/sub 2/ is attributed to characteristics of the nucleation - and growth- controlled transformation process

Effect of Energetic Materials on Thermal Decomposition of Phase-Stabilised Ammonium Nitrate - An Eco-Friendly Oxidiser

OpenAIRE

Suresh Mathew; K. Krishnan; K. N. Ninan

1999-01-01

Phase-stabilised ammonium nitrate (PSAN) was prepared by incorporating copper (II) diamine nitrate in the ammonium nitrate (AN) crystal lattice, thereby avoiding the abrupt volume change within the useful temperature range. The effect of RDX on the thermal decomposition of PSAN has been investigated. Decomposition temperatures of PSAN and RDX are almost in the same temperature range. The synergetic effect of the interaction between PSAN and RDX resulted in a net exothermic reaction of PSAN. T...

3-lead electrocardiogram is more reliable than pulse oximetry to detect bradycardia during stabilisation at birth of very preterm infants.

Science.gov (United States)

Iglesias, Beatriz; Rodrí Guez, Marí A José; Aleo, Esther; Criado, Enrique; Martí Nez-Orgado, Jose; Arruza, Luis

2018-05-01

Current neonatal resuscitation guidelines suggest the use of ECG in the delivery room (DR) to assess heart rate (HR). However, reliability of ECG compared with pulse oximetry (PO) in a situation of bradycardia has not been specifically investigated. The objective of the present study was to compare HR monitoring using ECG or PO in a situation of bradycardia (HR <100 beats per minute (bpm)) during preterm stabilisation in the DR. Video recordings of resuscitations of infants <32 weeks of gestation were reviewed. HR readings in a situation of bradycardia (<100 bpm) at any moment during stabilisation were registered with both devices every 5 s from birth. A total of 29 episodes of bradycardia registered by the ECG in 39 video recordings were included in the analysis (n=29). PO did not detect the start of these events in 20 cases (69%). PO detected the start and the end of bradycardia later than the ECG (median (IQR): 5 s (0-10) and 5 s (0-7.5), respectively). A decline in PO accuracy was observed as bradycardia progressed so that by the end of the episode PO offered significantly lower HR readings than ECG. PO detects the start and recovery of bradycardia events slower and less accurately than ECG during stabilisation at birth of very preterm infants. ECG use in this scenario may contribute to an earlier initiation of resuscitation manoeuvres and to avoid unnecessary prolongation of resuscitation efforts after recovery. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A stabilised nodal spectral element method for fully nonlinear water waves

DEFF Research Database (Denmark)

Engsig-Karup, Allan Peter; Eskilsson, C.; Bigoni, Daniele

2016-01-01

can cause severe aliasing problems and consequently numerical instability for marginally resolved or very steep waves. We show how the scheme can be stabilised through a combination of over-integration of the Galerkin projections and a mild spectral filtering on a per element basis. This effectively......We present an arbitrary-order spectral element method for general-purpose simulation of non-overturning water waves, described by fully nonlinear potential theory. The method can be viewed as a high-order extension of the classical finite element method proposed by Cai et al. (1998) [5], although...... the numerical implementation differs greatly. Features of the proposed spectral element method include: nodal Lagrange basis functions, a general quadrature-free approach and gradient recovery using global L2 projections. The quartic nonlinear terms present in the Zakharov form of the free surface conditions...

Sintering and thermal ageing studies of zirconia - yttria ceramics by impedance spectroscopy

International Nuclear Information System (INIS)

Florio, Daniel Zanetti de

1998-01-01

ZrO 2 :8 mol %Y 2 O 3 solid electrolyte ceramic pellets have been prepared with powders of three different origins: a Nissan (Japan) commercial powder, a powder obtained by the coprecipitation technique at IPEN, and the mixing of powder oxides (ZrO 2 produced at a Pilot Plant at IPEN and 99.9% pure Y 2 O 3 of USA origin). These starting powders have been analysed by the following techniques: X-ray fluorescence for yttrium content, X-ray diffraction for structural phase content, sedimentation for particle size distribution, gas adsorption (BET) for surface area determination, and transmission electron microscopy for average particle size determination. Pressed ceramic pellets have been analysed by dilatometry to evaluate the sintering stages. Sintered pellets have been characterized by X-ray diffraction for phase analysis and scanning electron microscopy for grain morphology analysis. Impedance spectroscopy analysis have been carried out to follow thermal ageing of zirconia-yttria solid electrolyte at 600 deg C, the working temperature of permanent oxygen sensor, and to study sintering kinetics. The main results show that ageing at 600 deg C decreases the emf sensor response in the first 100 h to a steady value. Moreover, sintering studies by impedance spectroscopy allowed for finding correlations between electrical parameters, sintering kinetics and grain growth mechanisms. (author)

Synthesis, microstructural, optical and mechanical properties of yttria stabilized zirconia thin films

International Nuclear Information System (INIS)

Amézaga-Madrid, P.; Hurtado-Macías, A.; Antúnez-Flores, W.; Estrada-Ortiz, F.; Pizá-Ruiz, P.; Miki-Yoshida, M.

2012-01-01

Highlights: ► Thin films of YSZ obtained by AACVD have high quality. ► They are uniform, very transparent, and have high hardness. ► Optical characterization were performed in detail, optical constants and band gap energy were determined as a function of dopant content. - Abstract: Thin films of yttria-stabilized zirconia (YSZ) exhibit exceptional properties, such as high thermal, chemical and mechanical stability. Here, we report the synthesis of YSZ thin films by aerosol assisted chemical vapour deposition onto borosilicate glass and fused silica substrates. Optimum deposition temperature was 673 ± 5 K. In addition, different Y content was tried to analyse its influence in the microstructure and properties of the films. The films were uniform, transparent and non-light scattering. Surface morphology and cross sectional microstructure were studied by field emission scanning electron microscopy. The microstructure of the films was characterized by grazing incidence X-ray diffraction. Crystallite size and lattice parameter were obtained. Optical properties were analysed from reflectance and transmittance spectra; from these measurements, optical constants and band gap were obtained. Quantum confinement effect, due to the small grain size of the films, was evident in the high band gap energy obtained. Nanoindentation tests were realized at room temperature employing the continuous stiffness measurement method, to determine the hardness and elastic modulus as a function of Y content.

Effect of Co3O4 addition on densification of 8 mil% Yttria stabilized zirconia

International Nuclear Information System (INIS)

Grilo, J.P.F.; Neto, P.P.B.; Souza, G.L.; Macedo, D.A.; Paskocimas, C.A.; Nascimento, R.M.

2012-01-01

8 mol% Yttria stabilized zirconia (8YSZ) is the most common material used as electrolyte in solid oxide fuel cells (SOFC). In recent years, many research efforts have been focused on trying to reduce its sintering temperature with a view of the possibility of co-sintering of the anode/electrolyte interface. In this context, the use of sintering aids is a major technological routes used to enhance the densification of YSZ. In this work, Co 3 O 4 powders obtained by the Pechini method were used as sintering aids for 8YSZ. The effect of the addition of Co 3 O 4' (between 0.075 and 1 wt.%) in the densification of 8YSZ was investigated by X-ray diffraction, electron microscopy and density measurements. The results indicated that the optimum temperature sintering decreases with increasing content of Co 3 O 4 . The best content of the sintering aid was 0.25 wt.%, for this content was obtained value of relative density above 90% after sintering at temperatures as low as 1350 deg C. (author)

Atom probe characterization of yttria particles in ODS Eurofer steel

International Nuclear Information System (INIS)

Aleev, A.A.; Zaluzhny, A.G.; Nikitin, A.A.; Rogozhkin, S.V.; Iskandarov, N.A.; Vladimirov, P.; Moeslang, A.; Lindau, R.; Klimenkov, M.

2009-01-01

Oxide dispersion strengthened steels exhibit higher temperature and radiation resistance than conventionally produced ferritic/martensitic steels. Such behaviour, as believed, is mainly caused by presence of highly dispersed and extremely stable oxide particles with sizes of few nanometers. It was shown that the most promising oxide additive was yttria (Y 2 O 3 ) and as mechanical parameters were strongly depended on size and number density of formed peculiarities it is required to reduce their dimensions to few nanometers and drastically increase their number. At present, considerable effort is focused on investigation of behaviour and properties of such particles. Recent studies of Eurofer ODS steel (9%-CrWVTa) by SANS and PoAS revealed the presence of high number density structural peculiarities with size approximately one nanometer. At the same time, previous studies by TEM identified only high number of small (5-10 nm) Y 2 O 3 particles. So, the purpose of this work was to look into this material by means of tomographic atom probe and find out the chemistry and origin of peculiarities with sizes less than 5 nm. These investigations revealed fine (∼ 2 nm) particles that were enriched not only in yttrium and oxygen but also in vanadium and nitrogen. Concentration of vanadium in them is approximately at the same level as yttrium. Moreover, some particles were found to be enriched in only three or even two elements mentioned above. However, total concentration of chemical elements in these particles is considerably less than that of iron. Estimated number density for detected particles is (1 / 5) x 10 23 m -3 . (author)

Effect of impregnation of La0.85Sr0.15MnO3/Yttria Stabilized Zirconia Solid Oxide Fuel Cell cathodes with La0.85Sr0.15MnO3 or Al2O3 nano-particles

DEFF Research Database (Denmark)

Kammer Hansen, Kent; Wandel, Marie; Liu, Yi-Lin

2010-01-01

Strontium substituted lanthanum manganite and yttria stabilized zirconia solid oxide fuel cell composite electrodes were impregnated with nano-particles of strontium substituted lanthanum manganite or alumina. A clear positive effect was observed on low performing electrodes and on good performing...

Surface modification of yttria stabilized zirconia via polydopamine inspired coating for hydroxyapatite biomineralization

Science.gov (United States)

Zain, Norhidayu Muhamad; Hussain, Rafaqat; Kadir, Mohammed Rafiq Abdul

2014-12-01

Yttria stabilized zirconia (YSZ) has been widely used as biomedical implant due to its high strength and enhanced toughening characteristics. However, YSZ is a bioinert material which constrains the formation of chemical bonds with bone tissue following implantation. Inspired by the property of mussels, the surface of YSZ ceramics was functionalized by quinone-rich polydopamine to facilitate the biomineralization of hydroxyapatite. YSZ discs were first immersed in 2 mg/mL of stirred or unstirred dopamine solution at either 25 or 37 °C. The samples were then incubated in 1.5 simulated body fluid (SBF) for 7d. The effect of coating temperature for stirred and unstirred dopamine solutions during substrate grafting was investigated on the basis of chemical compositions, wettability and biomineralization of hydroxyapatite on the YSZ functionalized surface. The results revealed that the YSZ substrate grafted at 37 °C in stirred solution of dopamine possessed significantly improved hydrophilicity (water contact angle of 44.0 ± 2.3) and apatite-mineralization ability (apatite ratio of 1.78). In summary, the coating temperature and stirring condition during grafting procedure affected the chemical compositions of the films and thus influenced the formation of apatite layer on the substrate during the biomineralization process.

Microstructural evolution and stability of tetragonal precipitates in Y2O3 partially-stabilized ZrO2 single crystals

International Nuclear Information System (INIS)

Martinez-Fernandez, J.; Jimenez-Melendo, M.; Dominguez-Rodriguez, A.

1995-01-01

The microstructure and morphology of tetragonal precipitates (t-ZrO 2 ) in yttria partially-stabilized zirconia single crystals containing various amounts of Y 2 O 3 (3, 4, 4.7 and 5.8 mol%) have been studied as a function of aging time at 1,600 C in air. The precipitate size and volume fraction of t-ZrO 2 phase were determined using transmission electron microscopy. The evolution of the precipitate volume fraction with aging time indicated that the precipitation reaction was completed after 24 h of annealing, in agreement with the values of the Y 2 O 3 composition in the matrix measured by analytical electron microscopy. Further aging coarsened the precipitates which joined together forming fiber-like particles of several micrometers in length and remaining untransformed despite their large size. The stability of the t-ZrO 2 precipitates against the tetragonal to monoclinic transformation in the ZrO 2 -Y 2 O 3 system seems to be related to interactions between precipitates due to coherency stresses rather than with their morphological characteristics

Sintering effect on material properties of electrochemical reactors used for removal of nitrogen oxides and soot particles emitted from diesel engines

DEFF Research Database (Denmark)

He, Zeming; Andersen, Kjeld Bøhm; Keel, Li

2010-01-01

In the present work, 12-layered electrochemical reactors (comprising five cells) with a novel configuration including supporting layer lanthanum strontium manganate (LSM)-yttria stabilised zirconia (YSZ), electrode layer LSM-gadolinia-doped cerium oxide (CGO) and electrolyte layer CGO were...... fabricated via the processes of slurry preparation, tape casting and lamination and sintering. The parameters of porosity, pore size, pore size distribution, shrinkage, flow rate of the sintered reactors and the electrical conductivities of the supporting layer and the electrode in the sintered reactors were...... characterised. The effect of sintering temperature on microstructures and properties of the sintered samples was discussed, and 1,250 °C was determined as the appropriate sintering temperature for reactor production based on the performance requirements for applications. Using the present ceramic processing...

Colorimetric Detection Based on Localised Surface Plasmon Resonance Optical Characteristics for the Detection of Hydrogen Peroxide Using Acacia Gum–Stabilised Silver Nanoparticles

Directory of Open Access Journals (Sweden)

Eman Alzahrani

2017-02-01

Full Text Available The use of nanoparticles in sensing is attracting the interest of many researchers. The aim of this work was to fabricate Acacia gum–stabilised silver nanoparticles (SNPs using green chemistry to use them as a highly sensitive and cost-effective localised surface plasmon resonance (LSPR colorimeter sensor for the determination of reactive oxygen species, such as hydrogen peroxide (H 2 O 2 . Silver nanoparticles were fabricated by the reduction of an inorganic precursor silver nitrate solution (AgNO 3 using white sugar as the reducing reagent and Acacia gum as the stabilising reagent and a sonication bath to form uniform silver nanoparticles. The fabricated nanoparticles were characterised by visual observation, ultraviolet-visible (UV-Vis spectrophotometry, transmission electron microscopy (TEM analysis, energy-dispersive X-ray spectroscopy (EDAX, thermogravimetric analysis (TGA, and Fourier transform infrared spectroscopy (FT-IR. The TEM micrographs of the synthesised nanoparticles showed the presence of spherical nanoparticles with sizes of approximately 10 nm. The EDAX spectrum result confirmed the presence of silver (58%, carbon (30%, and oxygen (12%. Plasmon colorimetric sensing of H 2 O 2 solution was investigated by introducing H 2 O 2 solution into Acacia gum–capped SNP dispersion, and the change in the LSPR band in the UV-Vis region of spectra was monitored. In this study, it was found that the yellow colour of Acacia gum–stabilised SNPs gradually changed to transparent, and moreover, a remarkable change in the LSPR absorbance strength was observed. The calibration curve was linear over 0.1–0.00001 M H 2 O 2 , with a correlation estimation ( R 2 of .953. This was due to the aggregation of SNPs following introduction of the H 2 O 2 solution. Furthermore, the fabricated SNPs were successfully used to detect H 2 O 2 solution in a liquid milk sample, thereby demonstrating the ability of the fabricated SNPs to detect H 2 O 2

The influence of pigments on the slow crack growth in dental zirconia

NARCIS (Netherlands)

Aboushelib, M.N.; de Jager, N.; Kleverlaan, C.J.; Feilzer, A.J.

2012-01-01

Objectives Partially yttria stabilized zirconium oxide was introduced as core material for core-veneered full ceramic dental restorations, because of its biological inertness, high mechanical strength, and toughness. In order to improve the esthetical possibilities pigments in the core are

Dominant pinning mechanisms in YBa2Cu3O7-x films on single and polycrystalline yttria stabilized zirconia substrates

Science.gov (United States)

Harshavardhan, K. S.; Rajeswari, M.; Hwang, D. M.; Chen, C. Y.; Sands, T.; Venkatesan, T.; Tkaczyk, J. E.; Lay, K. W.; Safari, A.

1992-04-01

Critical-current densities have been measured in YBa2Cu3O7-x films deposited on (100) yttria stabilized zirconia (YSZ) and polycrystalline YSZ substrates as a function of temperature (4.5-88 K), magnetic field (0-1 T) and orientation relative to the applied field. The results indicate that in films on polycrystalline substrates, surface and interface pinning play a dominant role at high temperatures. In films on (100) YSZ, pinning is mainly due to intrinsic layer pinning as well as extrinsic pinning associated with the interaction of the fluxoids with point defects and low energy planar (2D) boundaries. The differences are attributed to the intrinsic rigidity of single fluxoids which is reduced in films on polycrystalline substrates thereby weakening the intrinsic layer pinning.

Cathodic behaviour of nonstoichiometric (la,Sr){sub 1-x}(Co,Mn)O{sub 3} materials

Energy Technology Data Exchange (ETDEWEB)

Abrantes, J.C.C.; Rodrigues, C.M.S. [ESTG, Inst. Politecnico Viana do Castelo (Portugal); Labrincha, J.A.; Frade, J.R.; Marques, F.M.B. [Aveiro Univ. (Portugal). Dept. de Engenharia de Ceramica e do Vidro

1996-10-01

Solid oxide fuel cells (SOFCs) are expected to become competitive devices for electrical power generation, but successful application might be dependent on decreasing working temperatures to 800{sup o}C or lower, without detrimental effects on electrode processes and ohmic losses. This requires alternative electrode and electrolyte materials. The high electronic and oxygen ion conductivities of (La,Sr)CoO{sub 3} are promising for oxygen reduction, but high temperature reaction with yttria-stabilised zirconia (YSZ) electrolytes and excessive thermal expansion mismatch have prevented the current application of these cathode materials. Expected ways to try to minimise the reactivity of cobaltates involve A-site deficiency, and partial Mn for Co substitution. The latter is also expected to contribute to lower the thermal expansion mismatch. In this work (La,Sr){sub 1-x}(Co,Mn)O{sub 3} materials were prepared by solid state reaction and characterised by X-ray diffraction, thermal expansion and electrical conductivity measurements. The reactivity between these electrode materials and YSZ was also evaluated by XRD and SEM. Electrode layers were screen-printed on YSZ substrates and cathodic polarisation was measured at temperatures up to 1000{sup o}C. A-site substoichiometry and Co for Mn substitution affect the cathodic polarisation, but this also depends on some morphological features of screen-printed electrode layers. (author)

Failure mechanism for thermal fatigue of thermal barrier coating systems

Energy Technology Data Exchange (ETDEWEB)

Giolli, C.; Scrivani, A.; Rizzi, G. [Turbocoating S.p.A., Rubbiano di Solignano (Italy); Borgioli, F. [Firenze Univ., Sesto Fiorentino (Italy); Bolelli, G.; Lusvarghi, L. [Univ. di Modena e Reggio Emilia, Modena (Italy)

2008-07-01

High temperature thermal fatigue causes the failure of Thermal Barrier Coating (TBC) systems. Due to the difference in thickness and microstructure between thick TBCs and traditional thin TBCs, they cannot be assumed a-priori to possess the same failure mechanisms. Thick TBCs, consisting of a CoNiCrAlY bond coat and Yttria Partially Stabilised Zirconia top coat with different values of porosity, were produced by Air Plasma Spray. Thermal fatigue resistance limit of TBCs was tested by Furnace Cycling Tests (FCT) according to the specifications of an Original Equipment Manufacturer (OEM). TBC systems were analyzed before and after FCT. The morphological and chemical evolution of CoNiCrAlY/TGO microstructure was studied. Sintering effect, residual stress, phase transformation and fracture toughness were evaluated in the ceramic Top Coat. All the tested samples passed FCT according to the specification of an important OEM. Thermal fatigue resistance increases with the amount of porosity in the top coat. The compressive in-plane stresses increase in the TBC systems after thermal cycling, nevertheless the increasing rate has a trend contrary to the porosity level of top coat. The data suggest that the spallation happens at the TGO/Top Coat interface. The failure mechanism of thick TBCs subjected to thermal fatigue was eventually found to be similar to the failure mechanism of thin TBC systems made by APS. (orig.)

Geotechnical and mineralogical characterisations of marine-dredged sediments before and after stabilisation to optimise their use as a road material.

Science.gov (United States)

Saussaye, L; van Veen, E; Rollinson, G; Boutouil, M; Andersen, J; Coggan, J

2017-12-01

Dredging activities to extend, deepen and maintain access to harbours generate significant volumes of waste dredged material. Some ways are investigated to add value to these sediments. One solution described here is their use in road construction following treatment with hydraulic binders. This paper presents the characterisation of four sediments, in their raw state and after 90 days of curing following stabilisation treatment with lime and cement, using a combination of novel and established analytical techniques to investigate subsequent changes in mineralogy. These sediments are classified as fine, moderately to highly organic and highly plastic and their behaviour is linked to the presence of smectite clays. The main minerals found in the sediments using X-ray diffraction (XRD) and automated mineralogy are quartz, calcite, feldspars, aluminium silicates, pyrite and halite. Stabilisation was found to improve the mechanical performances of all the sediments. The formation of cementitious hydrates was not specifically detected using automated mineralogy or XRD. However, a decrease in the percentage volume of aluminium silicates and aluminium-iron silicates and an increase of the percentage volume of feldspars and carbonates was observed.

Stabilisation and humanitarian access in a collapsed state: the Somali case.

Science.gov (United States)

Menkhaus, Ken

2010-10-01

Somalia today is the site of three major threats: the world's worst humanitarian crisis; the longest-running instance of complete state collapse; and a robust jihadist movement with links to Al-Qa'ida. External state-building, counter-terrorism and humanitarian policies responding to these threats have worked at cross-purposes. State-building efforts that insist humanitarian relief be channelled through the nascent state in order to build its legitimacy and capacity undermine humanitarian neutrality when the state is a party to a civil war. Counter-terrorism policies that seek to ensure that no aid benefits terrorist groups have the net effect of criminalising relief operations in countries where poor security precludes effective accountability. This paper argues that tensions between stabilisation and humanitarian goals in contemporary Somalia reflect a long history of politicisation of humanitarian operations in the country. © 2010 The Author(s). Journal compilation © Overseas Development Institute, 2010.

Post-{gamma}-irradiation reactions in vitamin E stabilised and unstabilised HDPE

Energy Technology Data Exchange (ETDEWEB)

Mallegol, J.; Carlsson, D.J. E-mail: dave.carlsson@nrc.ca; Deschenes, L

2001-12-01

The oxidation of high density polyethylene (HDPE), both unstabilised and vitamin E stabilised, has been studied by infrared (IR) and electron paramagnetic resonance (EPR) spectroscopies in the period following {gamma}-irradiation at doses from 1 to 60 kGy (range of food sterilisation). Derivatisation by reaction with sulphur tetrafluoride was used to identify macro-ketone and carboxylic acid components of the overlapped IR carbonyl region. Oxidation continued for several hundred hours after the cessation of irradiation as shown by the increase in hydroxyl, ketone and acid groups. Carboxylic acid groups are particularly important as a direct indication of backbone scission. Vitamin E, although an effective antioxidant during {gamma}-irradiation, was less effective in reducing the post-irradiation changes, which are probably driven by migration of radical sites along the polymer backbone from within the crystalline phase to the amorphous/crystalline inter-phase, where they become oxygen accessible.

Effect of highly dispersed yttria addition on thermal stability of hydroxyapatite

Energy Technology Data Exchange (ETDEWEB)

Parente, P., E-mail: pparente@icv.csic.es [Instituto de Ceramica y Vidrio, CSIC, C/Kelsen 5, Madrid 28049 (Spain); Savoini, B. [Departamento de Fisica, Universidad Carlos III de Madrid, Avda. Universidad 30, Leganes 28911 (Spain); Ferrari, B. [Instituto de Ceramica y Vidrio, CSIC, C/Kelsen 5, Madrid 28049 (Spain); Monge, M.A.; Pareja, R. [Departamento de Fisica, Universidad Carlos III de Madrid, Avda. Universidad 30, Leganes 28911 (Spain); Sanchez-Herencia, A.J. [Instituto de Ceramica y Vidrio, CSIC, C/Kelsen 5, Madrid 28049 (Spain)

2013-03-01

The capability of the colloidal method to produce yttria (Y{sub 2}O{sub 3}) dispersed hydroxyapatite (HA) has been investigated as an alternative method to the conventional method of mechanical mixing and sintering for developing HA-based materials that could exhibit controllable and enhanced functional properties. A water based colloidal route to produce HA materials with highly dispersed Y{sub 2}O{sub 3} has been applied, and the effect of 10 wt.% Y{sub 2}O{sub 3} addition to HA investigated by thermal analysis, X-ray diffraction and Fourier transform infrared spectroscopy. These measurements evidence a remarkable effect of this Y{sub 2}O{sub 3} addition on decomposition mechanisms of synthetic HA. Results show that incorporation of Y{sub 2}O{sub 3} as dispersed second phase is beneficial because it hinders the decomposition mechanisms of HA into calcium phosphates. This retardation will allow the control of the sintering conditions for developing HA implants with improved properties. Besides, substitution of Ca{sup 2+} with Y{sup 3+} ions appears to promote the formation of OH{sup -} vacancies, which could improve the conductive properties of HA favorable to osseointegration. - Highlights: Black-Right-Pointing-Pointer We reveal the influence of Y{sub 2}O{sub 3} on thermal stability of hydroxyapatite. Black-Right-Pointing-Pointer Incorporation of Y{sub 2}O{sub 3} delays decomposition of hydroxyapatite to calcium phosphates. Black-Right-Pointing-Pointer Addition of Y{sub 2}O{sub 3} enables sintering conditions more favorable to the densification.

One-stage lengthening and derotational osteotomy of the femur stabilised with a gamma nail.

Science.gov (United States)

van Doorn, R; Leemans, R; Stapert, J W

1999-12-01

To study the results of a one-stage lengthening and derotational osteotomy stabilised with a Gamma nail. Retrospective study. 2 hospitals, The Netherlands. 5 patients after failed osteosynthesis of femoral fractures. Mean lengthening of 3 cm and derotation of 30 degrees. Complications and functional results, after a mean follow-up of 43 months (range 30-57). Two patients required dynamisation and a cancellous bone graft to achieve union, which resulted in 1 and 1.5 cm loss of length. One patient had a temporary peroneal neurapraxy. No infections were observed. Our method is not an ultimate solution, but is suitable for one-stage lengthening and derotation osteotomies.

The potential for ionic liquid electrolytes to stabilise the magnesium interface for magnesium/air batteries

International Nuclear Information System (INIS)

Khoo, Timothy; Howlett, Patrick C.; Tsagouria, Maureen; MacFarlane, Douglas R.; Forsyth, Maria

2011-01-01

Magnesium/air batteries are a possible high-energy density power source that, to date, have not received strong commercial interest due to issues with the corrosion of the magnesium and evaporation of the electrolyte. In this work we report on the use of ionic liquid based electrolytes to stabilise the metal/electrolyte interface and their impact on the electrochemical performance. Galvanostatic measurements indicate that the water content of the ionic liquid electrolyte plays an important role in the cell discharge characteristics. Surface characterisation using EIS, ATR-FTIR and powder diffraction examined the unique properties of the surface film formed on the magnesium anode.

Influence of surface treatment of yttria-stabilized tetragonal zirconia polycrystal with hot isostatic pressing on cyclic fatigue strength.

Science.gov (United States)

Iijima, Toshihiko; Homma, Shinya; Sekine, Hideshi; Sasaki, Hodaka; Yajima, Yasutomo; Yoshinari, Masao

2013-01-01

Hot isostatic pressing processed yttria-stabilized tetragonal zirconia polycrystal (HIP Y-TZP) has the potential for application to implants due to its high mechanical performance. The aim of this study was to investigate the influence of surface treatment of HIP Y-TZP on cyclic fatigue strength. HIP Y-TZP specimens were subjected to different surface treatments. Biaxial flexural strength was determined by both static and cyclic fatigue testing. In the cyclic fatigue test, the load was applied at a frequency of 10 Hz for 10(6) cycles in distilled water at 37°C. The surface morphology, roughness, and crystal phase of the surfaces were also evaluated. The cyclic fatigue strength (888 MPa) of HIP Y-TZP with sandblasting and acid-etching was more than twice that of Y-TZP as specified in ISO 13356 for surgical implants (320 MPa), indicating the clinical potential of this material.

Study of crystallite size of yttria-stabilized zirconia powders by Rietveld method

International Nuclear Information System (INIS)

Leite, Wellington Claiton; Brinatti, Andre Mauricio; Ribeiro, Mauricio Aparecido; Andrade, Andre Vitor Chaves de; Chinelatto, Adriana Scoton Antonio; Chinelatto, Adilson Luiz

2009-01-01

The yttria-stabilized zirconia (YSZ) is used in a great variety of applications, for example, electrolytes of solid oxide fuel cells and oxygen sensors. In the study of YSZ, the particle size powders and sintering processes are important to define the final properties of the zirconia products. The objectives of this work were to determine the phases and the crystalline size using X-Ray Diffraction (XRD) data and the Rietveld Method (RM) of the YSZ powders obtained by chemical synthesis based on the Pechini method. It was used ZrOCl 2.8 H 2 O and Y(NO 3 ) 3.5 H 2 O as precursors reagents. After calcination at 550 deg C during 24 hours, the powder was analyzed by XRD and scanning electronic microscopy (SEM). From XRD and using Rietveld method were verified that there is only cubic phase with lattice parameter a = 5.1307(1) Å and the space group Fm3m. Due to substitution of the Zr atoms in the Y atoms sites, there were vacancies in 17.72 % of O atoms sites. However, the percentage of substitution of Zr atoms in Y atoms sites in the structure not was determinate because the curves of atomic scattering of them are very similar. Using Scherrer equation and considering anisotropy effect, the average crystalline size was determinate: 10,43 nm (c axis) and 10,39 (b axis). This spherical symmetry also observed for SEM. (author)

Penetration and characteristics of an intergranular-liquid phase during sintering of CaSi2O5-dropped 8 mol%-yttria-stabilized zirconia estimation by impedance spectroscopy

International Nuclear Information System (INIS)

Jung, Young-Soo; Choi, Jung-Hae; Lee, Jong-Heun

2004-01-01

The grain-boundary resistivity of CaSi 2 O 5 -dropped 8 mol%-yttria-stabilized zirconia (8YSZ) was determined by impedance spectroscopy using sub-millimeter-scale electrodes. During sintering, a liquid that formed at the top surface of the specimen penetrated into the 8YSZ and induced enhanced grain growth near the surface region. The grain-boundary resistivity of the specimen surface was observed to be 150 times higher than that of the interior. The deterioration of the grain-boundary conductivity was explained in terms of the presence of an intergranular siliceous phase

Evaluation of tensile strength and fracture toughness of yttria-stabilized zirconia polycrystals with fracture surface analysis

International Nuclear Information System (INIS)

Oishi, Manabu; Matsuda, Yukihisa; Noguchi, Kenichi; Masaki, Takaki

1995-01-01

The tensile strength of yttria-stabilized tetragonal zirconia polycrystals (Y-TZPs) was measured and the fracture surfaces were analyzed with the scanning electron microscope and X-ray microanalyzer. The fracture origins of the pressureless-sintered samples were voids or inclusions such as Al 2 O 3 , Al 2 O 3 with SiO 2 , and cubic-ZrO 2 , while the fracture origins of the hot isostatically pressed samples were inclusions; no voids were detected at fracture origins. The higher strengths of the hot isostatically pressed samples versus those of the pressureless-sintered samples were consistent with the change in fracture origins. The fracture toughness of the samples calculate from the tensile strength and analysis of the fracture origins was 3.4 to 3.7 MPa ·√m. These values are lower than those measured with the SEPB method. These discrepancies might be caused by the difference in the state of the fracture origin and its neighborhood, such as the size of the fracture origin and interaction between two surfaces in the precrack

Zirconia dental implants : a clinical, radiographic, and microbiologic evaluation up to 3 years

NARCIS (Netherlands)

Brüll, Felix; van Winkelhoff, Arie Jan; Cune, Marco S.

2014-01-01

PURPOSE: To retrospectively evaluate the clinical performance of zirconia endosseous implants. MATERIALS AND METHODS: Partially edentulous patients with adequate bone volume to fit yttria tetragonal zirconia polycrystal (Y-TZP) implants at least 3.5 mm wide and 8.0 mm long were included. Full-mouth

International aviation emissions to 2025: Can emissions be stabilised without restricting demand?

International Nuclear Information System (INIS)

Macintosh, Andrew; Wallace, Lailey

2009-01-01

International aviation is growing rapidly, resulting in rising aviation greenhouse gas emissions. Concerns about the growth trajectory of the industry and emissions have led to calls for market measures such as emissions trading and carbon levies to be introduced to restrict demand and prompt innovation. This paper provides an overview of the science on aviation's contribution to climate change, analyses key trends in the industry since 1990, projects international civil aviation emissions to 2025 and analyses the emission intensity improvements that are necessary to offset rising international demand. The findings suggest international aviation carbon dioxide (CO 2 ) emissions will increase by more than 110 per cent between 2005 and 2025 (from 416 Mt to between 876 and 1013 Mt) and that it is unlikely emissions could be stabilised at levels consistent with risk averse climate targets without restricting demand

Does the oil fortune vanish with Kyoto. The effects on energy consumption and emissions from stabilising the CO2 concentration

International Nuclear Information System (INIS)

Lindholt, Lars; Rosendahl, Knut Einar

2000-01-01

The article discusses measures for and the consequences of stabilising the CO 2 concentration at various levels on the oil industry, the environment and the energy policies. The structure of an international taxation scenario will depend on which CO 2 level and forecasting model are selected as well as the time profiles and levels of CO 2 emissions in the various countries

Preparation and characterization of epitaxially grown unsupported yttria-stabilized zirconia (YSZ) thin films

Energy Technology Data Exchange (ETDEWEB)

Götsch, Thomas; Mayr, Lukas [Institute of Physical Chemistry, Universität Innsbruck, A-6020 Innsbruck (Austria); Stöger-Pollach, Michael [University Service Center for Transmission Electron Microscopy (USTEM), Vienna University of Technology, A-1040 Vienna (Austria); Klötzer, Bernhard [Institute of Physical Chemistry, Universität Innsbruck, A-6020 Innsbruck (Austria); Penner, Simon, E-mail: simon.penner@uibk.ac.at [Institute of Physical Chemistry, Universität Innsbruck, A-6020 Innsbruck (Austria)

2015-03-15

Highlights: • Preparation of unsupported yttrium-stabilized zirconia films. • Control of ordering and epitaxy by temperature of deposition template. • Adjustment of film defectivity by deposition and post-oxidation temperature. • Reproducibility of target stoichiometry in the deposited films. • Lateral and vertical chemical homogeneity. - Abstract: Epitaxially grown, chemically homogeneous yttria-stabilized zirconia thin films (“YSZ”, 8 mol% Y{sub 2}O{sub 3}) are prepared by direct-current sputtering onto a single-crystalline NaCl(0 0 1) template at substrate temperatures ≥493 K, resulting in unsupported YSZ films after floating off NaCl in water. A combined methodological approach by dedicated (surface science) analytical characterization tools (transmission electron microscopy and diffraction, atomic force microscopy, angle-resolved X-ray photoelectron spectroscopy) reveals that the film grows mainly in a [0 0 1] zone axis and no Y-enrichment in surface or bulk regions takes place. In fact, the Y-content of the sputter target is preserved in the thin films. Analysis of the plasmon region in EEL spectra indicates a defective nature of the as-deposited films, which can be suppressed by post-deposition oxidation at 1073 K. This, however, induces considerable sintering, as deduced from surface morphology measurements by AFM. In due course, the so-prepared unsupported YSZ films might act as well-defined model systems also for technological applications.

Magnetic and electronic properties of half-metallic ferromagnetic Mn-stabilised zirconia

Energy Technology Data Exchange (ETDEWEB)

Maznichenko, Igor; Daene, Markus; Hergert, Wolfram; Mertig, Ingrid [Martin-Luther-Univ. Halle-Wittenberg, Inst. Phys., 06099 Halle (Germany); Ernst, Arthur; Ostanin, Sergey; Sandratskii, Leonid; Bruno, Patrick [Max-Planck-Inst. Mikrostrukturphys., Weinberg 2, 06120 Halle (Germany); Bergqvist, Lars [Dept. Phys., Uppsala Univ., Box 530, 751 21 Uppsala (Sweden); Hughes, Ian; Staunton, Julie [Dept. Phys., Univ. Warwick, Coventry CV4 7AL (United Kingdom); Kudrnovsky, Josef [Max-Planck-Inst. Mikrostrukturphys., Weinberg 2, 06120 Halle (Germany); Inst. Phys., Acad. Sci. of the Czech Republic, Na Slovance 2, 18221 Prague (Czech Republic)

2007-07-01

The investigations of the manganese stabilised cubic zirconia (Mn-SZ) show that this dilute magnetic semiconductors possess unique magnetic properties. Based on ab-initio electronic structure calculations which include the effects of thermally excited magnetic fluctuations, the autors predict Mn-SZ to be ferromagnetic for a wide range of Mn concentration up to high T{sub C}. It was found that this material, which is well known both as a diamond imitation and as a catalyst, is halfmetallic with majority and minority spin states of the Mn impurities lying in the wide band gap of zirconia. The high T{sub C} ferromagnetism is robust against oxygen vacancies and against the distribution of Mn impurities on the Zr fcc sublattice. This work responds to the question concerning the key electronic and structure factors behind an optimal doping. The autors propose this stable half-metallic ferromagnet to be a promising candidate for future spintronics applications.

Three strategies to stabilise nearly monodispersed silver nanoparticles in aqueous solution

Science.gov (United States)

Stevenson, Amadeus PZ; Blanco Bea, Duani; Civit, Sergi; Antoranz Contera, Sonia; Iglesias Cerveto, Alberto; Trigueros, Sonia

2012-02-01

Silver nanoparticles are extensively used due to their chemical and physical properties and promising applications in areas such as medicine and electronics. Controlled synthesis of silver nanoparticles remains a major challenge due to the difficulty in producing long-term stable particles of the same size and shape in aqueous solution. To address this problem, we examine three strategies to stabilise aqueous solutions of 15 nm citrate-reduced silver nanoparticles using organic polymeric capping, bimetallic core-shell and bimetallic alloying. Our results show that these strategies drastically improve nanoparticle stability by distinct mechanisms. Additionally, we report a new role of polymer functionalisation in preventing further uncontrolled nanoparticle growth. For bimetallic nanoparticles, we attribute the presence of a higher valence metal on the surface of the nanoparticle as one of the key factors for improving their long-term stability. Stable silver-based nanoparticles, free of organic solvents, will have great potential for accelerating further environmental and nanotoxicity studies. PACS: 81.07.-b; 81.16.Be; 82.70.Dd.

Novel Cranial Implants of Yttria-Stabilized Zirconia as Acoustic Windows for Ultrasonic Brain Therapy.

Science.gov (United States)

Gutierrez, Mario I; Penilla, Elias H; Leija, Lorenzo; Vera, Arturo; Garay, Javier E; Aguilar, Guillermo

2017-11-01

Therapeutic ultrasound can induce changes in tissues by means of thermal and nonthermal effects. It is proposed for treatment of some brain pathologies such as Alzheimer's, Parkinson's, Huntington's diseases, and cancer. However, cranium highly absorbs ultrasound reducing transmission efficiency. There are clinical applications of transcranial focused ultrasound and implantable ultrasound transducers proposed to address this problem. In this paper, biocompatible materials are proposed for replacing part of the cranium (cranial implants) based on low porosity polycrystalline 8 mol% yttria-stabilized-zirconia (8YSZ) ceramics as acoustic windows for brain therapy. In order to assess the viability of 8YSZ implants to effectively transmit ultrasound, various 8YSZ ceramics with different porosity are tested; their acoustic properties are measured; and the results are validated using finite element models simulating wave propagation to brain tissue through 8YSZ windows. The ultrasound attenuation is found to be linearly dependent on ceramics' porosity. Results for the nearly pore-free case indicate that 8YSZ is highly effective in transmitting ultrasound, with overall maximum transmission efficiency of ≈81%, compared to near total absorption of cranial bone. These results suggest that 8YSZ polycrystals could be suitable acoustic windows for ultrasound brain therapy at 1 MHz. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Slow conduction in the border zones of patchy fibrosis stabilises the drivers for atrial fibrillation: Insights from multi-scale human atrial modelling

Directory of Open Access Journals (Sweden)

Ross Morgan

2016-10-01

Full Text Available Introduction. The genesis of atrial fibrillation (AF and success of AF ablation therapy have been strongly linked with atrial fibrosis. Increasing evidence suggests that patient-specific distributions of fibrosis may determine the locations of electrical drivers (rotors sustaining AF, but the underlying mechanisms are incompletely understood. This study aims to elucidate a missing mechanistic link between patient-specific fibrosis distributions and AF drivers. Methods. 3D atrial models integrated human atrial geometry, rule-based fibre orientation, region-specific electrophysiology and AF-induced ionic remodelling. A novel detailed model for an atrial fibroblast was developed, and effects of myocyte-fibroblast (M-F coupling were explored at single-cell, 1D tissue and 3D atria levels. Left atrial LGE MRI datasets from 3 chronic AF patients were segmented to provide the patient-specific distributions of fibrosis. The data was non-linearly registered and mapped to the 3D atria model. Six distinctive fibrosis levels (0 – healthy tissue, 5 – dense fibrosis were identified based on LGE MRI intensity and modelled as progressively increasing M-F coupling and decreasing atrial tissue coupling. Uniform 3D atrial model with diffuse (level 2 fibrosis was considered for comparison.Results. In single cells and tissue, the largest effect of atrial M-F coupling was on the myocyte resting membrane potential, leading to partial inactivation of sodium current and reduction of conduction velocity (CV. In the 3D atria, further to the M-F coupling, effects of fibrosis on tissue coupling greatly reduce atrial CV. AF was initiated by fast pacing in each 3D model with either uniform or patient-specific fibrosis. High variation in fibrosis distributions between the models resulted in varying complexity of AF, with several drivers emerging. In the diffuse fibrosis models, waves randomly meandered through the atria, whereas in each the patient-specific models, rotors

Embolisation of pheochromocytoma to stabilise and wean a patient in cardiogenic shock from emergency extracorporeal life support

DEFF Research Database (Denmark)

Vagner, Helle; Hey, Thomas Morris; Elle, Bo

2015-01-01

Pheochromocytoma is a catecholamine-secreting tumour associated with varying symptoms ranging from episodic headache, sweating, paroxysmal hypertension and tachycardia to intractable cardiogenic shock. Cardiogenic shock is rare but well-described and the timing of correct management is crucial si...... since mortality is high. Fifty per cent of pheochromocytomas are diagnosed on autopsy. We report on a case of embolisation of the adrenal artery during ongoing extracorporeal life support (ECLS) in order to stabilise and wean the patient from ECLS as a bridge to final surgery....

Effects of agrochemicals, ultra violet stabilisers and solar radiation on the radiometric properties of greenhouse films

Directory of Open Access Journals (Sweden)

Giuliano Vox

2013-10-01

Full Text Available Agrochemicals, based on iron, sulphur and chlorine, generate by products that lead to a degradation of greenhouse films together with a decrease in their mechanical and physical properties. The degradation due to agrochemicals depends on their active principles, method and frequency of application, and greenhouse ventilation. The aim of the research was to evaluate how agrochemical contamination and solar radiation influence the radiometric properties of ethylene-vinyl acetate copolymer greenhouse films by means of laboratory and field tests. The films, manufactured on purpose with the addition of different light stabiliser systems, were exposed to natural outdoor weathering at the experimental farm of the University of Bari (Italy; 41° 05’ N in the period from 2006 to 2008. Each film was tested for two low tunnels: one low tunnel was sprayed from inside with the agrochemicals containing iron, chlorine and sulphur while the other one was not sprayed and served as control. Radiometric laboratory tests were carried out on the new films and on samples taken at the end of the trials. The experimental tests showed that both the natural weathering together with the agrochemicals did not modify significantly the radiometric properties of the films in the solar and in the photosynthetically active radiation wavelength range. Within six months of experimental field tests the variations in these radiometric characteristics were at most 10%. Significant variations, up to 70% of the initial value, were recorded for the stabilised films in the long-wave infrared radiation wavelength range.

SINTESIS NANOPARTIKEL PERAK MENGGUNAKAN METODE POLIOL DENGAN AGEN STABILISATOR POLIVINILALKOHOL (PVA

Directory of Open Access Journals (Sweden)

DOB Apriandanu

2014-06-01

Full Text Available Abstrak __________________________________________________________________________________________ Nanopartikel perak merupakan produk berbasis nanoteknologi yang sedang berkembang saat ini dan dapat diaplikasikan sebagai katalis dan detektor sensor optik. Faktor yang dapat mempengaruhi ukuran nanopartikel adalah konsentrasi garam dan agen pereduksi. Nanopartikel perak bersifat tidak stabil. Oleh karena itu, perlu adanya penambahan polivinil alkohol sebagai agen stabilisator dalam sintesis nanopartikel perak. Tujuan penelitian ini adalah untuk mengetahui pengaruh rasio mol reduktor EG/Ag+ dan % PVA (b/v dalam sintesis nanopartikel perak terhadap karakteristik produk yang dihasilkan. Nanopartikel perak disintesis dengan metode poliol yaitu melarutkan AgNO3 ke dalam etilen glikol sebagai reduktor dan polivinilalkohol (PVA sebagai stabilisator. Karakterisasi dilakukan menggunakan Spek-trofotometer UV-Vis dan TEM (Transmission Electron Microscope. Analisis terhadap spektra UV-Vis menunjukkan bahwa nanopartikel yang relatif stabil pada pengukuran panjang gelombang maksimum 417 hingga 418 nm adalah nanopartikel yang disintesis menggunakan PVA 3%. Karakterisasi dengan TEM menunjukkan nanopartikel perak yang disintesis berdasarkan rasio mol etilen glikol terhadap Ag+ 50:1 memiliki ukuran terkecil dengan kisaran 10,15–27,56 nm dengan struktur kristal face centered cubic (FCC. Semakin tinggi rasio mol EG /Ag+ dalam sintesis nanopartikel perak, semakin tinggi pula peningkatan absorbansinya.   Abstract __________________________________________________________________________________________ Silver nanoparticles are nanotechnology based product which can be applied as a catalyst and optic sensor detector. The factors that can effect on nanoparticle size are salt concentration and reductor agent. Silver nanoparticles are unstable material, so polyvinylalcohol needs to be added  as a stabilizer agent in their synthesis. The aims of this research are to

Long-term olfactory memories are stabilised via protein synthesis in Camponotus fellah ants

DEFF Research Database (Denmark)

Guerrieri, Fernando Javier; D'Ettorre, Patrizia; Deveaud, J-M.

2011-01-01

-chain hydrocarbons, one paired with sucrose and the other with quinine solution. Differential conditioning leads to the formation of a long-term memory retrievable at least 72¿h after training. Long-term memory consolidation was impaired by the ingestion of cycloheximide, a protein synthesis blocker, prior...... to conditioning. Cycloheximide did not impair acquisition of either short-term memory (10¿min) or early and late mid-term memories (1 or 12¿h). These results show that, upon olfactory learning, ants form different memories with variable molecular bases. While short- and mid-term memories do not require protein...... synthesis, long-term memories are stabilised via protein synthesis. Our behavioural protocol opens interesting research avenues to explore the cellular and molecular bases of olfactory learning and memory in ants....

Mixed conductor anodes: Ni as electrocatalyst for hydrogen conversion

DEFF Research Database (Denmark)

Primdahl, S.; Mogensen, Mogens Bjerg

2002-01-01

Five types of anodes for solid oxide fuel cells (SOFC) are examined on an yttria-stabilised zirconia (YSZ) electrolyte by impedance spectroscopy at 850 degreesC in hydrogen. The examined porous anodes are a Ni/Zr(0.92)Y(0.16)O(2.08) (Ni/YSZ) cermet, a Ni/Ce(0.9)Gd(0.1)O(1.95) (Ni/CGI) cermet, a Ce......(0.6)Gd(0.4)O(1.8) (CG4) ceramic, a La(0.75)Sr(0.25)Cr(0.97)V(0.03)O(3) (LSCV) ceramic and a Ti(0.22) Y(0.16)Zr(0.92)O(2.52) (TiYSZ) ceramic, Addition of small amounts ( approximate to I w/o) of Ni to the electrode surface is found to improve electrode performance on mixed electronic and ionic...

Birch Bark Dry Extract by Supercritical Fluid Technology: Extract Characterisation and Use for Stabilisation of Semisolid Systems

Directory of Open Access Journals (Sweden)

Markus Armbruster

2017-03-01

Full Text Available Triterpene compounds like betulin, betulinic acid, erythrodiol, oleanolic acid and lupeol are known for many pharmacological effects. All these substances are found in the outer bark of birch. Apart from its pharmacological effects, birch bark extract can be used to stabilise semisolid systems. Normally, birch bark extract is produced for this purpose by extraction with organic solvents. Employing supercritical fluid technology, our aim was to develop a birch bark dry extract suitable for stabilisation of lipophilic gels with improved properties while avoiding the use of toxic solvents. With supercritical carbon dioxide, three different particle formation methods from supercritical solutions have been tested. First, particle deposition was performed from a supercritical solution in an expansion chamber. Second, the Rapid Expansion of Supercritical Solutions (RESS method was used for particle generation. Third, a modified RESS-procedure, forming the particles directly into the thereby gelated liquid, was developed. All three methods gave yields from 1% to 5.8%, depending on the techniques employed. The triterpene composition of the three extracts was comparable: all three gave more stable oleogels compared to the use of an extract obtained by organic solvent extraction. Characterizing the rheological behaviour of these gels, a faster gelling effect was seen together with a lower concentration of the extract required for the gel formation with the supercritical fluid (SCF-extracts. This confirms the superiority of the supercritical fluid produced extracts with regard to the oleogel forming properties.

Fast reactor irradiation effects on fracture toughness of Si_3N_4 in comparison with MgAl_2O_4 and yttria stabilized ZrO_2

International Nuclear Information System (INIS)

Tada, K.; Watanabe, M.; Tachi, Y.; Kurishita, H.; Nagata, S.; Shikama, T.

2016-01-01

Fracture toughness of silicon nitride (Si_3N_4), magnesia-alumina spinel (MgAl_2O_4) and yttria stabilized zirconia (8 mol%Y_2O_3–ZrO_2) was evaluated by the Vickers-indentation technique after the fast reactor irradiation up to 55 dpa (displacement per atom) at about 700 °C in the Joyo. The change of the fracture toughness by the irradiation was correlated with nanostructural evolution by the irradiation, which was examined by transmission electron microscopy. The observed degradation of fracture toughness in Si_3N_4 is thought to be due to the relatively high density of small-sized of the irradiation induced defects, which should be resulted from a large amount of transmutation gases of hydrogen and helium. Observed improvement of fracture toughness in MgAl_2O_4 was due to the blocking of crack propagation by the antiphase boundaries. The radiation effects affected the fracture toughness of yttria stabilized zirconia at 55 dpa, suggesting that the generated high density voids would affect the propagation of cracks. - Highlights: • Si_3N_4, MgAl_2O_4 and YSZ were neutron irradiated up to 55dpa around 700 °C in the Joyo. • They are candidate ceramics for the inert matrices of nuclear fuels in the fast reactors. • The irradiation enhanced the fracture toughness of MgAl_2O_4 and YSZ, while degraded that of Si_3N_4. • The toughness changes were correlated with radiation induced defects and transmutation gases.

The Use of the String of Pearls Locking Plate System in the Stabilisation of a Comminuted Calcaneal Fracture in a Giant Breed Dog

Directory of Open Access Journals (Sweden)

A. B. Scrimgeour

2011-01-01

Full Text Available An eight-year-old male Pyrenean mountain dog was presented with a comminuted fracture of the right calcaneus following motor vehicle trauma. The fracture was stabilised with a plate-rod construct, using the String of Pearls locking plate system and an intramedullary pin. Healing was uncomplicated.

Oil-in-water emulsions stabilised by cellulose ethers: stability, structure and in vitro digestion.

Science.gov (United States)

Borreani, Jennifer; Espert, María; Salvador, Ana; Sanz, Teresa; Quiles, Amparo; Hernando, Isabel

2017-04-19

The effect of cellulose ethers in oil-in-water emulsions on stability during storage and on texture, microstructure and lipid digestibility during in vitro gastrointestinal digestion was investigated. All the cellulose ether emulsions showed good physical and oxidative stability during storage. In particular, the methylcellulose with high methoxyl substituents (HMC) made it possible to obtain emulsions with high consistency which remained almost unchanged during gastric digestion, and thus could enhance fullness and satiety perceptions at gastric level. Moreover, the HMC emulsion slowed down lipid digestion to a greater extent than a conventional protein emulsion or the emulsions stabilised by the other cellulose ethers. Therefore, HMC emulsions could be used in weight management to increase satiation capacity and decrease lipid digestion.

Moduli stabilisation for chiral global models

International Nuclear Information System (INIS)

Cicoli, Michele; Mayrhofer, Christoph; Valandro, Roberto

2011-10-01

We combine moduli stabilisation and (chiral) model building in a fully consistent global set-up in Type IIB/F-theory. We consider compactifications on Calabi-Yau orientifolds which admit an explicit description in terms of toric geometry. We build globally consistent compactifications with tadpole and Freed-Witten anomaly cancellation by choosing appropriate brane set-ups and world-volume fluxes which also give rise to SU(5)- or MSSM-like chiral models. We fix all the Kaehler moduli within the Kaehler cone and the regime of validity of the 4D effective field theory. This is achieved in a way compatible with the local presence of chirality. The hidden sector generating the non-perturbative effects is placed on a del Pezzo divisor that does not have any chiral intersections with any other brane. In general, the vanishing D-term condition implies the shrinking of the rigid divisor supporting the visible sector. However, we avoid this problem by generating r< n D-term conditions on a set of n intersecting divisors. The remaining (n-r) flat directions are fixed by perturbative corrections to the Kaehler potential. We illustrate our general claims in an explicit example. We consider a K3-fibred Calabi-Yau with four Kaehler moduli, that is an hypersurface in a toric ambient space and admits a simple F-theory up-lift. We present explicit choices of brane set-ups and fluxes which lead to three different phenomenological scenarios: the first with GUT-scale strings and TeV-scale SUSY by fine-tuning the background fluxes; the second with an exponentially large value of the volume and TeV-scale SUSY without fine-tuning the background fluxes; and the third with a very anisotropic configuration that leads to TeV-scale strings and two micron-sized extra dimensions. The K3 fibration structure of the Calabi-Yau three-fold is also particularly suitable for cosmological purposes. (orig.)

Moduli stabilisation for chiral global models

Energy Technology Data Exchange (ETDEWEB)

Cicoli, Michele [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Abdus Salam International Centre for Theoretical Physics, Trieste (Italy); Mayrhofer, Christoph [Heidelberg Univ. (Germany). Inst. fuer Theoretische Physik; Valandro, Roberto [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

2011-10-15

We combine moduli stabilisation and (chiral) model building in a fully consistent global set-up in Type IIB/F-theory. We consider compactifications on Calabi-Yau orientifolds which admit an explicit description in terms of toric geometry. We build globally consistent compactifications with tadpole and Freed-Witten anomaly cancellation by choosing appropriate brane set-ups and world-volume fluxes which also give rise to SU(5)- or MSSM-like chiral models. We fix all the Kaehler moduli within the Kaehler cone and the regime of validity of the 4D effective field theory. This is achieved in a way compatible with the local presence of chirality. The hidden sector generating the non-perturbative effects is placed on a del Pezzo divisor that does not have any chiral intersections with any other brane. In general, the vanishing D-term condition implies the shrinking of the rigid divisor supporting the visible sector. However, we avoid this problem by generating r

The Effective Governance Gap in EU Counter-Terrorism and Stabilisation Policy for Somalia

Directory of Open Access Journals (Sweden)

EJ Hogendoorn

2017-12-01

Full Text Available For more than two decades, the EU and other donors have spent billions of euros to rebuild the Somali state and, more recently, to counter the rise of the violent Islamist group Al Shabaab. But Somalia remains a weak, if not “failed state”, and progress is nowhere near commensurate with international support. This is because donors failed to generate enough Somali political will to reform dysfunctional and corrupt administrations that undermine their programmes, as well as counter-terrorism and stabilisation goals. To be more effective, the EU needs to become more adept at understanding local political dynamics as well as better at employing carrots and sticks to nudge Somali leaders to support governance reform and better administration. Otherwise, its expensive technical assistance and training programmes may have only temporary and limited impact.

Stabilisation of Na,K-ATPase structure by the cardiotonic steroid ouabain.

Science.gov (United States)

Miles, Andrew J; Fedosova, Natalya U; Hoffmann, Søren V; Wallace, B A; Esmann, Mikael

2013-05-31

Cardiotonic steroids such as ouabain bind with high affinity to the membrane-bound cation-transporting P-type Na,K-ATPase, leading to complete inhibition of the enzyme. Using synchrotron radiation circular dichroism spectroscopy we show that the enzyme-ouabain complex is less susceptible to thermal denaturation (unfolding) than the ouabain-free enzyme, and this protection is observed with Na,K-ATPase purified from pig kidney as well as from shark rectal glands. It is also shown that detergent-solubilised preparations of Na,K-ATPase are stabilised by ouabain, which could account for the successful crystallisation of Na,K-ATPase in the ouabain-bound form. The secondary structure is not significantly affected by the binding of ouabain. Ouabain appears however, to induce a reorganization of the tertiary structure towards a more compact protein structure which is less prone to unfolding; recent crystal structures of the two enzymes are consistent with this interpretation. These circular dichroism spectroscopic studies in solution therefore provide complementary information to that provided by crystallography. Copyright © 2013 The Author. Published by Elsevier Inc. All rights reserved.

Cooperation of distinct Rac-dependent pathways to stabilise E-cadherin adhesion.

Science.gov (United States)

Erasmus, Jennifer C; Welsh, Natalie J; Braga, Vania M M

2015-09-01

The precise mechanisms via which Rac1 is activated by cadherin junctions are not fully known. In keratinocytes Rac1 activation by cadherin junctions requires EGFR signalling, but how EGFR does so is unclear. To address which activator could mediate E-cadherin signalling to Rac1, we investigated EGFR and two Rac1 GEFs, SOS1 and DOCK180. EGFR RNAi prevented junction-induced Rac1 activation and led to fragmented localization of E-cadherin at cadherin contacts. In contrast, depletion of another EGFR family member, ErbB3, did not interfere with either process. DOCK180 RNAi, but not SOS1, prevented E-cadherin-induced Rac1 activation. However, in a strong divergence from EGFR RNAi phenotype, DOCK180 depletion did not perturb actin recruitment or cadherin localisation at junctions. Rather, reduced DOCK180 levels impaired the resistance to mechanical stress of pre-formed cell aggregates. Thus, within the same cell type, EGFR and DOCK180 regulate Rac1 activation by newly-formed contacts, but control separate cellular events that cooperate to stabilise junctions. Copyright © 2015. Published by Elsevier Inc.

Temperature-dependent thermal conductivity of flexible yttria-stabilized zirconia substrate via 3ω technique

Energy Technology Data Exchange (ETDEWEB)

Singh, Shivkant; Yarali, Milad; Mavrokefalos, Anastassios [Department of Mechanical Engineering, University of Houston, Houston, TX (United States); Shervin, Shahab [Materials Science and Engineering Program, University of Houston, Houston, TX (United States); Venkateswaran, Venkat; Olenick, Kathy; Olenick, John A. [ENrG Inc., Buffalo, NY (United States); Ryou, Jae-Hyun [Department of Mechanical Engineering, University of Houston, Houston, TX (United States); Materials Science and Engineering Program, University of Houston, Houston, TX (United States); Texas Center for Superconductivity, University of Houston (TcSUH), Houston, TX (United States)

2017-10-15

Thermal management in flexible electronic has proven to be challenging thereby limiting the development of flexible devices with high power densities. To truly enable the technological implementation of such devices, it is imperative to develop highly thermally conducting flexible substrates that are fully compatible with large-scale fabrication. Here, we present the thermal conductivity of state-of-the-art flexible yttria-stabilized zirconia (YSZ) substrates measured using the 3ω technique, which is already commercially manufactured via roll-to-roll technique. We observe that increasing the grain size increases the thermal conductivity of the flexible 3 mol.% YSZ, while the flexibility and transparency of the sample are hardly affected by the grain size enlargement. We exhibit thermal conductivity values of up to 4.16 Wm{sup -1}K {sup -1} that is at least 4 times higher than state-of-the-art polymeric flexible substrates. Phonon-hopping model (PHM) for granular material was used to fit the measured thermal conductivity and accurately define the thermal transport mechanism. Our results show that through grain size optimization, YSZ flexible substrates can be realized as flexible substrates, that pave new avenues for future novel application in flexible electronics through the utilization of both their ceramic structural flexibility and high heat dissipating capability. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Thickness determination of large-area films of yttria-stabilized zirconia produced by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Pryds, N. [Materials Research Department, Riso National Laboratory, DK-4000 Roskilde (Denmark)]. E-mail: nini.pryds@risoe.dk; Toftmann, B. [Department of Optics and Plasma Research, Riso National Laboratory, DK-4000 Roskilde (Denmark); Bilde-Sorensen, J.B. [Materials Research Department, Riso National Laboratory, DK-4000 Roskilde (Denmark); Schou, J. [Department of Optics and Plasma Research, Riso National Laboratory, DK-4000 Roskilde (Denmark); Linderoth, S. [Materials Research Department, Riso National Laboratory, DK-4000 Roskilde (Denmark)

2006-04-30

Films of yttria-stabilized zirconia (YSZ) on a polished silicon substrate of diameter up to 125 mm have been produced in a large-area pulsed laser deposition (PLD) setup under typical PLD conditions. The film thickness over the full film area has been determined by energy-dispersive X-ray spectrometry in a scanning electron microscope (SEM) with use of a method similar to one described by Bishop and Poole. The attenuation of the electron-induced X-rays from the Si wafer by the film was monitored at a number of points along a diameter and the thickness was determined by Monte Carlo simulations of the attenuation for various values of film thickness with the program CASINO. These results have been compared with direct measurements in the SEM of the film thickness on a cross-section on one of the wafers. The results of these measurements demonstrate the ability of this technique to accurately determine the thickness of a large film, i.e. up to diameters of 125 mm, in a relatively short time, without destroying the substrate, without the need of a standard sample and without the need of a flat substrate. We have also demonstrated that by controlling the deposition parameters large-area YSZ films with uniform thickness can be produced.

Thickness determination of large-area films of yttria-stabilized zirconia produced by pulsed laser deposition

International Nuclear Information System (INIS)

Pryds, N.; Toftmann, B.; Bilde-Sorensen, J.B.; Schou, J.; Linderoth, S.

2006-01-01

Films of yttria-stabilized zirconia (YSZ) on a polished silicon substrate of diameter up to 125 mm have been produced in a large-area pulsed laser deposition (PLD) setup under typical PLD conditions. The film thickness over the full film area has been determined by energy-dispersive X-ray spectrometry in a scanning electron microscope (SEM) with use of a method similar to one described by Bishop and Poole. The attenuation of the electron-induced X-rays from the Si wafer by the film was monitored at a number of points along a diameter and the thickness was determined by Monte Carlo simulations of the attenuation for various values of film thickness with the program CASINO. These results have been compared with direct measurements in the SEM of the film thickness on a cross-section on one of the wafers. The results of these measurements demonstrate the ability of this technique to accurately determine the thickness of a large film, i.e. up to diameters of 125 mm, in a relatively short time, without destroying the substrate, without the need of a standard sample and without the need of a flat substrate. We have also demonstrated that by controlling the deposition parameters large-area YSZ films with uniform thickness can be produced

Synthesis of Yttria-stabilized zirconia nanoparticles by decomposition of metal nitrates coated on carbon powder

International Nuclear Information System (INIS)

Jiang, S.; Stangle, G.C.; Amarakoon, V.R.; Schulze, W.A.

1996-01-01

Weakly agglomerated nanoparticles of yttria-stabilized zirconia (YSZ) were synthesized by a novel process which involved the decomposition of metal nitrates that had been coated on ultrafine carbon black powder, after which the carbon black was gasified. The use of ultrafine, high-surface-area carbon black powder apparently allowed the nanocrystalline oxide particles to form and remain separate from each other, after which the carbon black was gasified at a somewhat higher temperature. As a result, the degree of agglomeration was shown to be relatively low. The average crystallite size and the specific surface area of the as-synthesized YSZ nanoparticles were 5∼6 nm and 130 m 2 /g, respectively, for powder synthesized at 650 degree C. The as-synthesized YSZ nanoparticles had a light brown color and were translucent, which differs distinctly from conventional YSZ particles which are typically white and opaque. The mechanism of the synthesis process was investigated, and indicated that the gasification temperature had a direct effect on the crystallite size of the as-synthesized YSZ nanoparticles. High-density and ultrafine-grained YSZ ceramic articles were prepared by fast-firing, using a dwell temperature of 1250 degree C and a dwell time of two minutes or less. copyright 1996 Materials Research Society

Stabilisation of phytosterols by natural and synthetic antioxidants in high temperature conditions.

Science.gov (United States)

Kmiecik, Dominik; Korczak, Józef; Rudzińska, Magdalena; Gramza-Michałowska, Anna; Hęś, Marzanna; Kobus-Cisowska, Joanna

2015-04-15

The aim of the study was to assess the potential applicability of natural antioxidants in the stabilisation of phytosterols. A mixture of β-sitosterol and campesterol was incorporated into triacylglycerols (TAGs). The following antioxidants were added to the prepared matrix: green tea extract, rosemary extract, a mix of tocopherols from rapeseed oil, a mix of synthetic tocopherols, phenolic compounds extracted from rapeseed meal, sinapic acid and butylated hydroxytoluene (BHT). Samples were heated at a temperature of 180 °C for 4 h. After the completion of heating, the losses of phytosterols were analysed, as well as the contents of β-sitosterol and campesterol oxidation products. The total content of phytosterol oxidation products in samples ranged from 96.69 to 268.35 μg/g of oil. The effectiveness of antioxidants decreased in the following order: phenolic compounds from rapeseed meal>rosemary extract>mix of tocopherols from rapeseed oil>mix of synthetic tocopherols>green tea extract>sinapic acid>BHT. Copyright © 2014 Elsevier Ltd. All rights reserved.

Bond quality control of aluminium stabilised superconductors with ultrasonic phased-array technology

International Nuclear Information System (INIS)

Neuenschwander, J.; Luethi, T.; Horvath, I.L.

2001-01-01

Novel aluminium stabilised superconductors are currently being produced for the Large Hadron Collider detectors ATLAS and CMS. For a satisfying service of the conductor an intact bonding between the different constituents must be guaranteed. We have shown previously that ultrasonics is a powerful tool for checking the bond quality. However, up to now the full width of the bond could be inspected only on short samples with a mechanical scanner. The essence of this presentation is the introduction of the phased-array technique which allows a continuous analysis of the complete bond over km-long conductor units during their manufacture. For now, more than 50 km of conductor have been tested during co-extrusion. Disbondings are detected as regions with enhanced echo-amplitudes. We are about to set-up a second system for the control of an electron beam welding process which is used for the reinforcement of the CMS conductor. (orig.)

Vibration-tolerant narrow-linewidth semiconductor disk laser using novel frequency-stabilisation schemes

Science.gov (United States)

Hunter, Craig R.; Jones, Brynmor E.; Schlosser, Peter; Sørensen, Simon Toft; Strain, Michael J.; McKnight, Loyd J.

2018-02-01

This paper will present developments in narrow-linewidth semiconductor-disk-laser systems using novel frequencystabilisation schemes for reduced sensitivity to mechanical vibrations, a critical requirement for mobile applications. Narrow-linewidth single-frequency lasers are required for a range of applications including metrology and highresolution spectroscopy. Stabilisation of the laser was achieved using a monolithic fibre-optic ring resonator with free spectral range of 181 MHz and finesse of 52 to act as passive reference cavity for the laser. Such a cavity can operate over a broad wavelength range and is immune to a wide band of vibrational frequency noise due to its monolithic implementation. The frequency noise of the locked system has been measured and compared to typical Fabry-Perotlocked lasers using vibration equipment to simulate harsh environments, and analysed here. Locked linewidths of portable, narrow-linewidth laser system for harsh environments that can be flexibly designed for a range of applications.

Entropic stabilisation of topologically close-packed phases in binary transition-metal alloys

Energy Technology Data Exchange (ETDEWEB)

Hammerschmidt, Thomas; Fries, Suzana G.; Steinbach, Ingo; Drautz, Ralf [ICAMS, Ruhr-Universitaet Bochum, Bochum (Germany); Seiser, Bernhard; Pettifor, David G. [Department of Materials, University of Oxford, Oxford (United Kingdom)

2010-07-01

The formation of topologically close-packed (tcp) phases in Ni-based superalloys leads to the degradation of the mechanical properties of the alloys. The precipitation of the tcp phases is attributed to refractory elements that are added in low concentration to improve creep resistance. It is well known that the structural stability of the tcp phases A15, {sigma} and {chi} is driven by the average d-band filling. For a direct comparison to experimental phase diagrams, we carried out extensive density-functional theory (DFT) calculations of the tcp phases A15, C14, C15, C36, {mu}, {sigma}, and {chi} in tcp-forming binary transition-metal (TM) systems. We observe several systems such as W-Re with positive values of the heat of formation for all tcp phases although some of the phases are observed experimentally. By combining our DFT total energies with the CALPHAD methodology, we can demonstrate that configurational entropy can stabilise the tcp phases in these systems.

Median sternotomy and ventral stabilisation using pins and polymethylmethacrylate for a comminuted T5 vertebral fracture in a Miniature Schnauzer.

Science.gov (United States)

Guiot, L P; Allman, D A

2011-01-01

A 2.9 kg Miniature Schnauzer was referred to our clinic, the Emergency & Critical Care Medicine Service at the Michigan State University Veterinary Teaching Hospital, following a dog fight. Physical examination findings upon admission included multiple thoracic wounds, absence of hindlimb deep pain, and marked Schiff-Sherrington syndrome. Computed tomography imaging revealed thoracic wall penetration and a comminuted T5 vertebral fracture. Thoracic exploration and thoracic wall repair were performed through a median sternotomy. The vertebral fracture was exposed and stabilised intra-thoracically through the same approach using pins and polymethylmethacrylate. The pins were placed percutaneously into the vertebral bodies of the adjacent vertebrae. Recovery was uncomplicated and fracture healing was documented eight weeks postoperatively. Spinal trauma secondary to dog fights is relatively common. The presence of concurrent penetrating thoracic injury negatively affects prognosis and necessitates thoracic exploration as soon as feasible. The approach should allow complete thoracic exploration to repair parietal and visceral damage, thus indicating the need for median sternotomy rather than an intercostal approach. The present case report suggested that median sternotomy can be used to safely apply stabilisation devices for the treatment of concurrent spinal trauma. Direct visualisation of the vertebral bodies permitted optimal implant anchorage as compared to potentially more hazardous techniques such as dorsal pinning.

The performance of blended conventional and novel binders in the in-situ stabilisation/solidification of a contaminated site soil.

Science.gov (United States)

Wang, Fei; Wang, Hailing; Jin, Fei; Al-Tabbaa, Abir

2015-03-21

This paper presents an investigation of the effects of novel binders and pH values on the effectiveness of the in-situ stabilisation/solidification technique in treating heavy metals and organic contaminated soils after 1.5-year treatment. To evaluate the performance of different binders, made ground soils of SMiRT site, upto 5 m depth, were stabilised/solidified with the triple auger system and cores were taken for laboratory testing after treatment. Twenty four different binders were used including Portland cement (PC), ground granulated blastfurnace slag (GGBS), pulverised fuel ash (PFA), MgO and zeolite. Unconfined compressive strength (UCS), leachate pH and the leachability of heavy metals and total organics were applied to study the behaviours of binders in treating site soils. Under various contaminant level and binder level, the results show that UCS values were 22-3476 kPa, the leachability of the total organics was in the range of 22-241 mg/l and the heavy metals was in the range of 0.002-0.225 mg/l. In addition, the combination of GGBS and MgO at a ratio of 9:1 shows better immobilisation efficiency in treating heavy metals and organic contaminated soils after 1.5-year treatment, and the binding mechanisms under different binders were also discussed in this paper. Copyright © 2014 Elsevier B.V. All rights reserved.

Stabilising high energy orbit oscillations by the utilisation of centrifugal effects for rotating-tyre-induced energy harvesting

Science.gov (United States)

Zhang, Yunshun; Zheng, Rencheng; Nakano, Kimihiko; Cartmell, Matthew P.

2018-04-01

Nonlinear energy harvesters are frequently considered in preference to linear devices because they can potentially overcome the narrow frequency bandwidth limitations inherent to linear variants; however, the possibility of variable harvesting efficiency is raised for the nonlinear case. This paper proposes a rotational energy harvester which may be fitted into an automobile tyre, with the advantage that it may broaden the rotating frequency bandwidth and simultaneously stabilise high-energy orbit oscillations. By consideration of the centrifugal effects due to rotation, the overall restoring force will potentially be increased for a cantilever implemented within the harvester, and this manifests as an increase in its equivalent elastic stiffness. In addition, this study reveals that the initial potential well barriers become as shallow as those for a bistable system. When the rotational frequency increases beyond an identifiable boundary frequency, the system transforms into one with a potential barrier of a typical monostable system. On this basis, the inter-well motion of the bistable system can provide sufficient kinetic energy so that the cantilever maintains its high-energy orbit oscillation for monostable hardening behaviour. Furthermore, in a vehicle drive experiment, it has been shown that the effective rotating frequency bandwidth can be widened from 15 km/h-25 km/h to 10 km/h-40 km/h. In addition, it is confirmed that the centrifugal effects can improve the harvester performance, producing a mean power of 61 μW at a driving speed of 40 km/h, and this is achieved by stabilising the high-energy orbit oscillations of the rotational harvester.

Mechanisms for parasites removal in a waste stabilisation pond.

Science.gov (United States)

Reinoso, Roberto; Blanco, Saúl; Torres-Villamizar, Linda A; Bécares, Eloy

2011-04-01

A waste stabilisation pond (WSP) system formed by two anaerobic ponds, a facultative pond and a maturation pond was studied from December 2003 to September 2004 in north-western Spain in order to evaluate its efficiency in the removal of faecal indicator bacteria (total coliforms, Escherichia coli, faecal streptococci), coliphages, helminth eggs and protozoan (oo)cysts (Cryptosporidium and Giardia). Furthermore, sediment samples were collected from the bottom of the ponds to assess the settling rates and thus determine the main pathogen removal mechanisms in the WSPs system. The overall removal ranged from 1.4 log units for coliphages in the cold period to 5.0 log units for E. coli in the hot period. Cryptosporidium oocysts were reduced by an average of 96%, Giardia cysts by 98% and helminth eggs by 100%. The anaerobic ponds showed significantly higher surface removal rates (4.6, 5.2 and 3.7 log (oo)cysts/eggs removed m(-2) day(-1), respectively) than facultative and maturation ponds. Sunlight and water physicochemical conditions were the main factors influencing C. parvum oocysts removal both in the anaerobic and maturation ponds, whereas other factors like predation or natural mortality were more important in the facultative pond. Sedimentation, the most commonly proposed mechanism for cyst removal had, therefore, a negligible influence in the studied ponds.

Epitaxial growth of In-rich InGaN on yttria-stabilized zirconia and its application to metal–insulator–semiconductor field-effect transistors

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Atsushi; Lye, Khe Shin; Ueno, Kohei [Institute of Industrial Science, The University of Tokyo, Tokyo 153-8505 (Japan); Ohta, Jitsuo [Institute of Industrial Science, The University of Tokyo, Tokyo 153-8505 (Japan); PRESTO, Japan Science and Technology Agency, Saitama 332-0012 (Japan); Fujioka, Hiroshi, E-mail: hfujioka@iis.u-tokyo.ac.jp [Institute of Industrial Science, The University of Tokyo, Tokyo 153-8505 (Japan); ACCEL, Japan Science and Technology Agency, Tokyo 102-0076 (Japan)

2016-08-28

We grew In-rich In{sub x}Ga{sub 1-x}N films on yttria-stabilized zirconia (YSZ) substrates at low temperatures by pulsed sputtering deposition. It was found that single-crystal In{sub x}Ga{sub 1-x}N (0.63 ≤ x ≤ 0.82) films can be prepared without significant compositional fluctuations at growth temperatures below 500 °C. It was also found that the electrical properties of InGaN are strongly dependent on In composition, growth temperature, and film polarity. N-channel operation of the metal–insulator–semiconductor field-effect transistor (MISFET) with an ultrathin InGaN channel on the YSZ substrates was successfully demonstrated. These results indicate that an InGaN-based MISFET is a promising device for next-generation high-speed electronics.

Oil bodies as a potential microencapsulation carrier for astaxanthin stabilisation and safe delivery.

Science.gov (United States)

Acevedo, Francisca; Rubilar, Mónica; Jofré, Ignacio; Villarroel, Mario; Navarrete, Patricia; Esparza, Magdalena; Romero, Fernando; Vilches, Elías Alberto; Acevedo, Valentina; Shene, Carolina

2014-01-01

Astaxanthin (AST) is a valued molecule because of its high antioxidant properties. However, AST is extremely sensitive to oxidation, causing the loss of its bioactive properties. The purposes of this study were to define conditions for microencapsulating AST in oil bodies (OB) from Brassica napus to enhance its oxidative stability, and to test the bioactivity of the microencapsulated AST (AST-M) in cells. Conditions for maximising microencapsulation efficiency (ME) were determined using the Response Surface Methodology, obtaining a high ME (>99%). OB loaded with AST showed a strong electrostatic repulsion in a wide range of pH and ionic strengths. It was found that AST-M exposed to air and light was more stable than free AST. In addition, the protective effect of AST against intracellular ROS production was positively influenced by microencapsulation in OB. These results suggest that OB offer a novel option for stabilising and delivering AST.

Voltage and partial pressure dependent defect chemistry in (La,Sr)FeO3-δ thin films investigated by chemical capacitance measurements.

Science.gov (United States)

Schmid, Alexander; Rupp, Ghislain M; Fleig, Jürgen

2018-05-03

La0.6Sr0.4FeO3-δ (LSF) thin films of different thickness were prepared by pulsed laser deposition on yttria stabilized zirconia (YSZ) and characterized by using three electrode impedance spectroscopy. Electrochemical film capacitance was analyzed in relation to oxygen partial pressure (0.25 mbar to 1 bar), DC polarization (0 m to -600 m) and temperature (500 to 650 °C). For most measurement parameters, the chemical bulk capacitance dominates the overall capacitive properties and the corresponding defect chemical state depends solely on the oxygen chemical potential inside the film, independent of atmospheric oxygen pressure and DC polarization. Thus, defect chemical properties (defect concentrations and defect formation enthalpies) could be deduced from such measurements. Comparison with LSF defect chemical bulk data from the literature showed good agreement for vacancy formation energies but suggested larger electronic defect concentrations in the films. From thickness-dependent measurements at lower oxygen chemical potentials, an additional capacitive contribution could be identified and attributed to the LSF|YSZ interface. Deviations from simple chemical capacitance models at high pressures are most probably due to defect interactions.

Study of microstructure and mechanical properties of ceramics composites alumina-zirconia reinforced with yttria for inert coating of metal matrices used in the petroleum industry

International Nuclear Information System (INIS)

Pontual, J.O.; Silva, N.D.G.; Ferreira, R.A.S.; Yadava, Y.P.

2014-01-01

The storage and transportation of crude oil is complicated due to the hostile environment provided by this. Under these conditions, it is imperative to search for alternative solutions, using an inert coating to protect from corrosion caused by crude oil. In this work, alumina-zirconia ceramic composites with 5-20%w zirconia and 1 - 2%w yttria were produced through thermomechanical process. The structural and microstructural characterization of the sintered material was carried out by X-ray diffraction and scanning electron microscopy. Mechanical properties were analyzed by Vickers hardness tests. Currently, the pads are submerged in crude oil and after 30-60 days will be removed and sent for stability test.(author)

The Ni-YSZ interface

DEFF Research Database (Denmark)

Jensen, Karin Vels

The anode/electrolyte interface in solid oxide fuel cells (SOFC) is known to cause electrical losses. Geometrically simple Ni/yttria-stabilised zirconia (YSZ) interfaces were examined to gain information on the structural and chemical changes occurring during experiments at 1000°C in an atmosphere...... of 97% H2/3% H2O. Electrochemical impedance spectroscopy at open circuit voltage (OCV) and at anodic and cathodic polarisations (100 mV) was performed. A correlation of the electrical data with the structure development and the chemical composition was attempted. Nickel wires with different impurity...... between polarised and non-polarised samples. With pure nickel wires, however, the microstructures depended on the polarisation/non-polarisation conditions. At non-polarised conditions a hill and valley type structure was found. Anodic polarisation produced an up to 1 μm thick interface layer consisting...

Status of the inert matrix fuel program at PSI

International Nuclear Information System (INIS)

Ledergerber, G.; Degueldre, C.; Kasemeyer, U.; Stanculescu, A.; Paratte, J.M.; Chawla, R.

1997-01-01

Incineration of plutonium by a once-through cycle in LWRs utilising an inert matrix based fuel may prove to be an attractive way of making use of the energy of fissile plutonium and reducing both the hazard potential and the volumes of the waste. Yttria stabilised zirconia forms a solid solution with oxides of rare earth elements (e.g. erbium, cerium) and some actinides. The small absorption cross section, the excellent stability under irradiation, and the insolubility in acids and water recommends this material as an inert matrix. Neutronics calculations with erbium as burnable poison show that these compositions would be optimal from the reactivity point of view. A fuel element with an improved reactivity behaviour over its life cycle has been designed for possible introduction into a heterogeneous LWR core. (author). 16 refs., 1 tab., 10 figs

Advanced fuel cycles options for LWRs and IMF benchmark definition

International Nuclear Information System (INIS)

Breza, J.; Darilek, P.; Necas, V.

2008-01-01

In the paper, different advanced nuclear fuel cycles including thorium-based fuel and inert-matrix fuel are examined under light water reactor conditions, especially VVER-440, and compared. Two investigated thorium based fuels include one solely plutonium-thorium based fuel and the second one plutonium-thorium based fuel with initial uranium content. Both of them are used to carry and burn or transmute plutonium created in the classical UOX cycle. The inert-matrix fuel consist of plutonium and minor actinides separated from spent UOX fuel fixed in Yttria-stabilised zirconia matrix. The article shows analysed fuel cycles and their short description. The conclusion is concentrated on the rate of Pu transmutation and Pu with minor actinides cumulating in the spent advanced thorium fuel and its comparison to UOX open fuel cycle. Definition of IMF benchmark based on presented scenario is given. (authors)

Straight-chain halocarbon forming fluids for TRISO fuel kernel production – Tests with yttria-stabilized zirconia microspheres

Energy Technology Data Exchange (ETDEWEB)

Baker, M.P. [Nuclear Science and Engineering Program, Metallurgical and Materials Engineering Department, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); King, J.C., E-mail: kingjc@mines.edu [Nuclear Science and Engineering Program, Metallurgical and Materials Engineering Department, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Gorman, B.P. [Metallurgical and Materials Engineering Department, Colorado Center for Advanced Ceramics, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Braley, J.C. [Nuclear Science and Engineering Program, Chemistry and Geochemistry Department, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States)

2015-03-15

Highlights: • YSZ TRISO kernels formed in three alternative, non-hazardous forming fluids. • Kernels characterized for size, shape, pore/grain size, density, and composition. • Bromotetradecane is suitable for further investigation with uranium-based precursor. - Abstract: Current methods of TRISO fuel kernel production in the United States use a sol–gel process with trichloroethylene (TCE) as the forming fluid. After contact with radioactive materials, the spent TCE becomes a mixed hazardous waste, and high costs are associated with its recycling or disposal. Reducing or eliminating this mixed waste stream would not only benefit the environment, but would also enhance the economics of kernel production. Previous research yielded three candidates for testing as alternatives to TCE: 1-bromotetradecane, 1-chlorooctadecane, and 1-iodododecane. This study considers the production of yttria-stabilized zirconia (YSZ) kernels in silicone oil and the three chosen alternative formation fluids, with subsequent characterization of the produced kernels and used forming fluid. Kernels formed in silicone oil and bromotetradecane were comparable to those produced by previous kernel production efforts, while those produced in chlorooctadecane and iodododecane experienced gelation issues leading to poor kernel formation and geometry.

Reaction of yttria-stabilized zirconia with zirconium, silicon and Zircaloy-4 at high temperature: a compatibility study for cermet fuels

International Nuclear Information System (INIS)

Arima, T.; Tateyama, T.; Idemitsu, K.; Inagaki, Y.

2003-01-01

Compatibility studies for cermet (ceramic and metal) fuels have been completed for a temperature range of 1073-1423 K. A reaction between yttria-stabilized zirconia (YSZ), as a simulated fuel, and Zr, as a candidate for a metallic matrix, has been observed at temperatures ≥1273 K, which means the formation of a metallic reaction layer at the interface between YSZ and Zr and the occurrence of metallic phases inside the YSZ. Similar results were observed for the YSZ-Zry4 (cladding) system. On the other hand, the degree of reaction was relatively large for the YSZ-Si (metallic matrix) system, and Si diffused into the YSZ. However, the maximum fuel center-line temperature can be predicted to be less than ∼1273 K for cermet fuels. Therefore, compatibility between the ceramic fuel and the metallic matrix should be good under normal reactor operational conditions. Furthermore, since the temperature of the fuel-cladding gap is lower, the cermet fuel and the cladding material are compatible

High-Temperature Particulate Matter Filtration with Resilient Yttria-Stabilized ZrO2 Nanofiber Sponge.

Science.gov (United States)

Wang, Haolun; Lin, Sen; Yang, Shen; Yang, Xudong; Song, Jianan; Wang, Dong; Wang, Haiyang; Liu, Zhenglian; Li, Bo; Fang, Minghao; Wang, Ning; Wu, Hui

2018-05-01

Particulate matter (PM) is a major air pollutant in many regions, jeopardizing ecosystems and public health. Filtration at pollutant source is one of the most important ways to protect the environment, however, considering the high-temperature exhaust gas emissions, effective removal of PM and related pollutants from their sources remains a major challenge. In this study, a resilient, heat-resisting, and high-efficiency PM filter based on yttria-stabilized ZrO 2 (YSZ) nanofiber sponge produced with a scalable solution blow spinning process is reported. The porous 3D sponge composed of YSZ nanofibers is lightweight (density of 20 mg cm -3 ) and resilient at both room temperature and high temperatures. At room-temperature conditions, the YSZ nanofiber sponge exhibits 99.4% filtration efficiency for aerosol particles with size in the range of 20-600 nm, associated with a low pressure drop of only 57 Pa under an airflow velocity of 4.8 cm s -1 . At a high temperature of 750 °C, the ceramic sponge maintains a high filtration efficiency of 99.97% for PM 0.3-2.5 under a high airflow velocity of 10 cm s -1 . A practical vehicle exhaust filter to capture particles with filtration efficiency of >98.3% is also assembled. Hence, the YSZ nanofiber sponge has enormous potential to be applied in industry. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Role of yttria-stabilized zirconia produced by ion-beam-assisted deposition on the properties of RuO2 on SiO2/Si

International Nuclear Information System (INIS)

Jia, Q.X.; Arendt, P.; Groves, J.R.; Fan, Y.; Roper, J.M.; Foltyn, S.R.

1998-01-01

Highly conductive biaxially textured RuO 2 thin films were deposited on technically important SiO 2 /Si substrates by pulsed laser deposition, where yttria-stabilized zirconia (YSZ) produced by ion-beam-assisted-deposition (IBAD) was used as a template to enhance the biaxial texture of RuO 2 on SiO 2 /Si. The biaxially oriented RuO 2 had a room-temperature resistivity of 37 μΩ-cm and residual resistivity ratio above 2. We then deposited Ba 0.5 Sr 0.5 TiO 3 thin films on RuO 2 /IBAD-YSZ/SiO 2 /Si. The Ba 0.5 Sr 0.5 TiO 3 had a pure (111) orientation normal to the substrate surface and a dielectric constant above 360 at 100 kHz. copyright 1998 Materials Research Society

Quantitative analysis for in situ sintering of 3% yttria-stablized zirconia in the transmission electron microscope

International Nuclear Information System (INIS)

Majidi, Hasti; Holland, Troy B.; Benthem, Klaus van

2015-01-01

Studying particle-agglomerate systems compared to two-particle systems elucidates different stages of sintering by monitoring both pores and particles. We report on in situ sintering of 3% yttria-stablized zirconia particle agglomerates in the transmission electron microscope (TEM). Real-time TEM observations indicate neck formation and growth, particle coalescence and pore closure. A MATLAB-based image processing tool was developed to calculate the projected area of the agglomerate with and without internal pores during in situ sintering. We demonstrate the first densification curves generated from sequentially acquired TEM images. The in situ sintering onset temperature was then determined to be at 960 °C. Densification curves illustrated that the agglomerate projected area which excludes the internal observed pores also shrinks during in situ sintering. To overcome the common projection problem for TEM analyses, agglomerate mass-thickness maps were obtained from low energy-loss analysis combined with STEM imaging. The decrease in the projected area was directly related to the increase in mass-thickness of the agglomerate, likely caused by hidden pores existing in the direction of the beam. Access to shrinkage curves through in situ TEM analysis provides a new avenue to investigate fundamental mechanisms of sintering through directly correlating microstructural changes during consolidation with mesoscale densification behavior

Quantitative analysis for in situ sintering of 3% yttria-stablized zirconia in the transmission electron microscope

Energy Technology Data Exchange (ETDEWEB)

Majidi, Hasti [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616 (United States); Holland, Troy B. [Department of Mechanical Engineering, Colorado State University, Fort Collins, CO 80523 (United States); Benthem, Klaus van, E-mail: benthem@ucdavis.edu [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616 (United States)

2015-05-15

Studying particle-agglomerate systems compared to two-particle systems elucidates different stages of sintering by monitoring both pores and particles. We report on in situ sintering of 3% yttria-stablized zirconia particle agglomerates in the transmission electron microscope (TEM). Real-time TEM observations indicate neck formation and growth, particle coalescence and pore closure. A MATLAB-based image processing tool was developed to calculate the projected area of the agglomerate with and without internal pores during in situ sintering. We demonstrate the first densification curves generated from sequentially acquired TEM images. The in situ sintering onset temperature was then determined to be at 960 °C. Densification curves illustrated that the agglomerate projected area which excludes the internal observed pores also shrinks during in situ sintering. To overcome the common projection problem for TEM analyses, agglomerate mass-thickness maps were obtained from low energy-loss analysis combined with STEM imaging. The decrease in the projected area was directly related to the increase in mass-thickness of the agglomerate, likely caused by hidden pores existing in the direction of the beam. Access to shrinkage curves through in situ TEM analysis provides a new avenue to investigate fundamental mechanisms of sintering through directly correlating microstructural changes during consolidation with mesoscale densification behavior.

The Influence of Heat Treatments on the Porosity of Suspension Plasma-Sprayed Yttria-Stabilized Zirconia Coatings

Science.gov (United States)

Ekberg, Johanna; Ganvir, Ashish; Klement, Uta; Creci, Simone; Nordstierna, Lars

2018-02-01

Suspension plasma-sprayed coatings are produced using fine-grained feedstock. This allows to control the porosity and to achieve low thermal conductivity which makes the coatings attractive as topcoats in thermal barrier coatings (TBCs). Used in gas turbine applications, TBCs are exposed to high temperature exhaust gases which lead to microstructure alterations. In order to obtain coatings with optimized thermomechanical properties, microstructure alterations like closing of pores and opening of cracks have to be taken into account. Hence, in this study, TBC topcoats consisting of 4 mol.% yttria-stabilized zirconia were heat-treated in air at 1150 °C and thereafter the coating porosity was investigated using image analysis (IA) and nuclear magnetic resonance (NMR) cryoporometry. Both IA and NMR cryoporometry showed that the porosity changed as a result of the heat treatment for all investigated coatings. In fact, both techniques showed that the fine porosity decreased as a result of the heat treatment, while IA also showed an increase in the coarse porosity. When studying the coatings using scanning electron microscopy, it was noticed that finer pores and cracks disappeared and larger pores grew slightly and achieved a more distinct shape as the material seemed to become more compact.

Preparation and properties of yttria doped tetragonal zirconia polycrystal/Sr-doped barium hexaferrite ceramic composites

International Nuclear Information System (INIS)

Wang, Shanshan; Zhang, Chao; Guo, Ruisong; Liu, Lan; Yang, Yuexia; Li, Kehang

2015-01-01

Highlights: • The 3Y-TZP/Sr-doped barium ferrite composites were prepared. • The saturation magnetization was improved by 15% with Sr-doping. • The dispersion coefficient p could reflect the microscopic lattice variation. • The composite with x = 0.5 had the maximum fracture toughness of 8.3 MPa m 1/2 . - Abstract: The effects of substitution of Ba 2+ by Sr 2+ on the magnetic property of barium ferrite and addition barium ferrite secondary phase to the 3 mol% yttria-doped tetragonal zirconia polycrystal (3Y-TZP) matrix on the mechanical property of composites were investigated. The Sr-doped barium ferrite (Ba 1−x Sr x Fe 12 O 19 , x = 0, 0.25, 0.50 and 0.75) was synthesized by solid-state reaction in advance. Then 3Y-TZP/20 wt% Sr-doped barium ferrite composites were prepared by means of conventional ceramic method. It was found that a moderate amount of Sr added to barium ferrite could boost the saturation magnetization by 15% compared with the composites without Sr-doping. Besides, the composite with x = 0.50 possessed the best mechanical properties, such as 11.5 GPa for Vickers hardness and 8.3 MPa m 1/2 for fracture toughness, respectively. It was demonstrated that magnetic and mechanical properties of the composites could be harmonized by the incorporation of barium ferrite secondary phase

Voltage and partial pressure dependent defect chemistry in (La,Sr)FeO3–δ thin films investigated by chemical capacitance measurements

Science.gov (United States)

Rupp, Ghislain M.; Fleig, Jürgen

2018-01-01

La0.6Sr0.4FeO3–δ (LSF) thin films of different thickness were prepared by pulsed laser deposition on yttria stabilized zirconia (YSZ) and characterized by using three electrode impedance spectroscopy. Electrochemical film capacitance was analyzed in relation to oxygen partial pressure (0.25 mbar to 1 bar), DC polarization (0 m to –600 m) and temperature (500 to 650 °C). For most measurement parameters, the chemical bulk capacitance dominates the overall capacitive properties and the corresponding defect chemical state depends solely on the oxygen chemical potential inside the film, independent of atmospheric oxygen pressure and DC polarization. Thus, defect chemical properties (defect concentrations and defect formation enthalpies) could be deduced from such measurements. Comparison with LSF defect chemical bulk data from the literature showed good agreement for vacancy formation energies but suggested larger electronic defect concentrations in the films. From thickness-dependent measurements at lower oxygen chemical potentials, an additional capacitive contribution could be identified and attributed to the LSF|YSZ interface. Deviations from simple chemical capacitance models at high pressures are most probably due to defect interactions. PMID:29671421

Robust transient stabilisation problem for a synchronous generator in a power network

Science.gov (United States)

Verrelli, C. M.; Damm, G.

2010-04-01

The robust transient stabilisation problem (with stability proof€) of a synchronous generator in an uncertain power network with transfer conductances is rigorously formulated and solved. The generator angular speed and electrical power are required to be kept close, when mechanical and electrical perturbations occur, to the synchronous speed and mechanical input power, respectively, while the generator terminal voltage is to be regulated, when perturbations are removed, to its pre-fault reference constant value. A robust adaptive nonlinear feedback control algorithm is designed on the basis of a third-order model of the synchronous machine: only two system parameters (synchronous machine damping and inertia constants) along with upper and lower bounds on the remaining uncertain ones are supposed to be known. The conditions to be satisfied by the remote network dynamics for guaranteeing ℒ2 and ℒ∞ robustness and asymptotic relative speed and voltage regulation to zero are weaker than those required by the single machine-infinite bus approximation: dynamic interactions between the local deviations of the generator states from the corresponding equilibrium values and the remote generators states are allowed.

Stabilisation and precision pointing quadrupole magnets in the Compact Linear Collider (CLIC)

CERN Document Server

Janssens, Stef; Linde, Frank; van den Brand, Jo; Bertolini, Alessandro; Artoos, Kurt

This thesis describes the research done to provide stabilisation and precision positioning for the main beam quadrupole magnets of the Compact Linear Collider CLIC. The introduction describes why new particle accelerators are needed to further the knowledge of our universe and why they are linear. A proposed future accelerator is the Compact Linear Collider (CLIC) which consists of a novel two beam accelerator concept. Due to its linearity and subsequent single pass at the interaction point, this new accelerator requires a very small beam size at the interaction point, in order to increase collision effectiveness. One of the technological challenges, to obtain these small beam sizes at the interaction point, is to keep the quadrupole magnets aligned and stable to 1.5 nm integrated r.m.s. in vertical and 5 nm integrated root mean square (r.m.s.) in lateral direction. Additionally there is a proposal to create an intentional offset (max. 50 nm every 20 ms with a precision of +/- 1 nm), for several quadrupole ma...

Internal reforming characteristics of cermet supported solid oxide fuel cell using yttria stabilized zirconia fed with partially reformed methane

Science.gov (United States)

Momma, Akihiko; Takano, Kiyonami; Tanaka, Yohei; Negishi, Akira; Kato, Ken; Nozaki, Ken; Kato, Tohru; Ichigi, Takenori; Matsuda, Kazuyuki; Ryu, Takashi

In order to investigate the internal reforming characteristics in a cermet supported solid oxide fuel cell (SOFC) using YSZ as the electrolyte, the concentration profiles of the gaseous species along the gas flow direction in the anode were measured. Partially reformed methane using a pre-reformer kept at a constant temperature is supplied to the center of the cell which is operated with a seal-less structure at the gas outlet. The anode gas is sucked in via silica capillaries to the initially evacuated gas tanks. The process is simultaneously carried out using five sampling ports. The sampled gas is analyzed by a gas chromatograph. Most of the measurements are made at the cell temperature (T cell) of 750 °C and at various temperatures of the pre-reformer (T ref) with various fuel utilizations (U f) of the cell. The composition of the fuel at the inlet of the anode was confirmed to be almost the same as that theoretically calculated assuming equilibrium at the temperature of the pre-reformer. The effect of internal reforming in the anode is clearly observed as a steady decrease in the methane concentration along the flow axis. The effect of the water-gas shift reaction is also observed as a decrease in the CO 2 concentration and an increase of CO concentration around the gas inlet region, as the water-gas shift reaction inversely proceeds when T cell is higher than T ref. The diffusion of nitrogen from the seal-less outermost edge is observed, and the diffusion is confirmed to be more significant as U f decreases. The observations are compared with the results obtained by the SOFC supported by lanthanum gallate electrolyte. With respect to the internal reforming performance, the cell investigated here is found to be more effective when compared to the previously reported electrolyte supported cell.

Thickness dependence of the strain, band gap and transport properties of epitaxial In{sub 2}O{sub 3} thin films grown on Y-stabilised ZrO{sub 2}(111)

Energy Technology Data Exchange (ETDEWEB)

Zhang, K H L; Oropeza, F E; Egdell, R G [Department of Chemistry, Chemistry Research Laboratory, University of Oxford, Mansfield Road, Oxford OX1 3TA (United Kingdom); Lazarov, V K [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom); Veal, T D; McConville, C F [Department of Physics, University of Warwick, Coventry CV4 7AL (United Kingdom); Walsh, A, E-mail: Russell.egdell@chem.ox.ac.uk [Department of Chemistry, Kathleen Lonsdale Materials Chemistry, University College London, 20 Gordon Street, London WC1H 0AJ (United Kingdom)

2011-08-24

Epitaxial films of In{sub 2}O{sub 3} have been grown on Y-stabilised ZrO{sub 2}(111) substrates by molecular beam epitaxy over a range of thicknesses between 35 and 420 nm. The thinnest films are strained, but display a 'cross-hatch' morphology associated with a network of misfit dislocations which allow partial accommodation of the lattice mismatch. With increasing thickness a 'dewetting' process occurs and the films break up into micron sized mesas, which coalesce into continuous films at the highest coverages. The changes in morphology are accompanied by a progressive release of strain and an increase in carrier mobility to a maximum value of 73 cm{sup 2} V{sup -1} s{sup -1}. The optical band gap in strained ultrathin films is found to be smaller than for thicker films. Modelling of the system, using a combination of classical pair-wise potentials and ab initio density functional theory, provides a microscopic description of the elastic contributions to the strained epitaxial growth, as well as the electronic effects that give rise to the observed band gap changes. The band gap increase induced by the uniaxial compression is offset by the band gap reduction associated with the epitaxial tensile strain.

Internal reforming characteristics of cermet supported solid oxide fuel cell using yttria stabilized zirconia fed with partially reformed methane

Energy Technology Data Exchange (ETDEWEB)

Momma, Akihiko; Takano, Kiyonami; Tanaka, Yohei; Negishi, Akira; Kato, Ken; Nozaki, Ken; Kato, Tohru [Energy Technology Research Institute, National Institute of Advanced Industrial Science and Technology, 1-1-1 Umezono Tsukuba Ibaraki, 305-8568 (Japan); Ichigi, Takenori; Matsuda, Kazuyuki; Ryu, Takashi [Application Development Project, Corporate R and D, NGK Insulators, Ltd., 2-56 Suda-cho Mizuho-ku Nagoya-shi Aichi, 467-8530 (Japan)

2009-08-01

In order to investigate the internal reforming characteristics in a cermet supported solid oxide fuel cell (SOFC) using YSZ as the electrolyte, the concentration profiles of the gaseous species along the gas flow direction in the anode were measured. Partially reformed methane using a pre-reformer kept at a constant temperature is supplied to the center of the cell which is operated with a seal-less structure at the gas outlet. The anode gas is sucked in via silica capillaries to the initially evacuated gas tanks. The process is simultaneously carried out using five sampling ports. The sampled gas is analyzed by a gas chromatograph. Most of the measurements are made at the cell temperature (T{sub cell}) of 750 C and at various temperatures of the pre-reformer (T{sub ref}) with various fuel utilizations (U{sub f}) of the cell. The composition of the fuel at the inlet of the anode was confirmed to be almost the same as that theoretically calculated assuming equilibrium at the temperature of the pre-reformer. The effect of internal reforming in the anode is clearly observed as a steady decrease in the methane concentration along the flow axis. The effect of the water-gas shift reaction is also observed as a decrease in the CO{sub 2} concentration and an increase of CO concentration around the gas inlet region, as the water-gas shift reaction inversely proceeds when T{sub cell} is higher than T{sub ref}. The diffusion of nitrogen from the seal-less outermost edge is observed, and the diffusion is confirmed to be more significant as U{sub f} decreases. The observations are compared with the results obtained by the SOFC supported by lanthanum gallate electrolyte. With respect to the internal reforming performance, the cell investigated here is found to be more effective when compared to the previously reported electrolyte supported cell. (author)

Microfluidic Fabrication of Hydrocortisone Nanocrystals Coated with Polymeric Stabilisers

Directory of Open Access Journals (Sweden)

David F. Odetade

2016-12-01

Full Text Available Hydrocortisone (HC nanocrystals intended for parenteral administration of HC were produced by anti-solvent crystallisation within coaxial assemblies of pulled borosilicate glass capillaries using either co-current flow of aqueous and organic phases or counter-current flow focusing. The organic phase was composed of 7 mg/mL of HC in a 60:40 (v/v mixture of ethanol and water and the anti-solvent was milli-Q water. The microfluidic mixers were fabricated with an orifice diameter of the inner capillary ranging from 50 µm to 400 µm and operated at the aqueous to organic phase flow rate ratio ranging from 5 to 25. The size of the nanocrystals decreased with increasing aqueous to organic flow rate ratio. The counter-current flow microfluidic mixers provided smaller nanocrystals than the co-current flow devices under the same conditions and for the same geometry, due to smaller diameter of the organic phase stream in the mixing zone. The Z-average particle size of the drug nanocrystals increased from 210–280 nm to 320–400 nm after coating the nanocrystals with 0.2 wt % aqueous solution of hydroxypropyl methylcellulose (HPMC in a stirred vial. The differential scanning calorimetry (DSC and X-ray powder diffraction (XRPD analyses carried out on the dried nanocrystals stabilized with HPMC, polyvinyl pyrrolidone (PVP, and sodium lauryl sulfate (SLS were investigated and reported. The degree of crystallinity for the processed sample was lowest for the sample stabilised with HPMC and the highest for the raw HC powder.

Cast Partial Denture versus Acrylic Partial Denture for Replacement of Missing Teeth in Partially Edentulous Patients

Directory of Open Access Journals (Sweden)

Pramita Suwal

2017-03-01

Full Text Available Aim: To compare the effects of cast partial denture with conventional all acrylic denture in respect to retention, stability, masticatory efficiency, comfort and periodontal health of abutments. Methods: 50 adult partially edentulous patient seeking for replacement of missing teeth having Kennedy class I and II arches with or without modification areas were selected for the study. Group-A was treated with cast partial denture and Group-B with acrylic partial denture. Data collected during follow-up visit of 3 months, 6 months, and 1 year by evaluating retention, stability, masticatory efficiency, comfort, periodontal health of abutment. Results: Chi-square test was applied to find out differences between the groups at 95% confidence interval where p = 0.05. One year comparison shows that cast partial denture maintained retention and stability better than acrylic partial denture (p< 0.05. The masticatory efficiency was significantly compromising from 3rd month to 1 year in all acrylic partial denture groups (p< 0.05. The comfort of patient with cast partial denture was maintained better during the observation period (p< 0.05. Periodontal health of abutment was gradually deteriorated in all acrylic denture group (p

Quantitative analysis for in situ sintering of 3% yttria-stablized zirconia in the transmission electron microscope.

Science.gov (United States)

Majidi, Hasti; Holland, Troy B; van Benthem, Klaus

2015-05-01

Studying particle-agglomerate systems compared to two-particle systems elucidates different stages of sintering by monitoring both pores and particles. We report on in situ sintering of 3% yttria-stablized zirconia particle agglomerates in the transmission electron microscope (TEM). Real-time TEM observations indicate neck formation and growth, particle coalescence and pore closure. A MATLAB-based image processing tool was developed to calculate the projected area of the agglomerate with and without internal pores during in situ sintering. We demonstrate the first densification curves generated from sequentially acquired TEM images. The in situ sintering onset temperature was then determined to be at 960 °C. Densification curves illustrated that the agglomerate projected area which excludes the internal observed pores also shrinks during in situ sintering. To overcome the common projection problem for TEM analyses, agglomerate mass-thickness maps were obtained from low energy-loss analysis combined with STEM imaging. The decrease in the projected area was directly related to the increase in mass-thickness of the agglomerate, likely caused by hidden pores existing in the direction of the beam. Access to shrinkage curves through in situ TEM analysis provides a new avenue to investigate fundamental mechanisms of sintering through directly correlating microstructural changes during consolidation with mesoscale densification behavior. Copyright © 2014 Elsevier B.V. All rights reserved.

Microstructural and chemical changes at the Ni/YSZ interface

DEFF Research Database (Denmark)

Hansen, Karin Vels; Primdahl, Søren; Chorkendorff, Ib

2001-01-01

A bent nickel wire was pressed against a yttria-stabilised zirconia (YSZ) surface, creating a small contact area. The Ni/YSZ interface was investigated and characteristic microstructures were found to develop during 200-300 h heat treatment at 1000 degreesC in 97% H-2/3% H2O with and without...... contact area on the YSZ developed a hill and valley structure with an amplitude of 100 nm. The nickel wires showed negative imprints of the YSZ structures. (C) 2001 Elsevier Science B.V. All rights reserved....... polarisation. A ridge of impurities up to 1.6 mum high was seen to develop along the Ni/YSZ/H-2 boundary. The impurity phase can be characterised as an alkali silicate phase containing Mn, Na, Ti, Mg, K, Al and Si. Most of these elements seem to be coming from impurities in the nickel. The initially flat...

A high performance ceria based interdiffusion barrier layer prepared by spin-coating

DEFF Research Database (Denmark)

Plonczak, Pawel; Joost, Mario; Hjelm, Johan

2011-01-01

A multiple spin-coating deposition procedure of Ce0.9Gd0.1O1.95 (CGO) for application in solid oxide fuel cells (SOFCs) was developed. The thin and dense CGO layer can be employed as a barrier layer between yttria stabilised zirconia (YSZ) electrolyte and a (La, Sr)(Co, Fe)O3 based cathode....... The decomposition of the polymer precursor used in the spin-coating process was studied. The depositions were performed on anode supported half cells. By controlling the sintering temperature between each spin-coating process, dense and crack-free CGO films with a thickness of approximately 1 μm were obtained....... The successive steps of dense layer production was investigated by scanning electron microscopy. X-ray diffraction was employed to monitor the crystal structure of the CGO layer sintered at different temperatures. The described spin coated barrier layer was evaluated using an anode supported cell...

Gap-metric-based robustness analysis of nonlinear systems with full and partial feedback linearisation

Science.gov (United States)

Al-Gburi, A.; Freeman, C. T.; French, M. C.

2018-06-01

This paper uses gap metric analysis to derive robustness and performance margins for feedback linearising controllers. Distinct from previous robustness analysis, it incorporates the case of output unstructured uncertainties, and is shown to yield general stability conditions which can be applied to both stable and unstable plants. It then expands on existing feedback linearising control schemes by introducing a more general robust feedback linearising control design which classifies the system nonlinearity into stable and unstable components and cancels only the unstable plant nonlinearities. This is done in order to preserve the stabilising action of the inherently stabilising nonlinearities. Robustness and performance margins are derived for this control scheme, and are expressed in terms of bounds on the plant nonlinearities and the accuracy of the cancellation of the unstable plant nonlinearity by the controller. Case studies then confirm reduced conservatism compared with standard methods.

Selective hydrogen detection at high temperature by using yttria-stabilized zirconia-based sensor with coupled metal-oxide-based sensing electrodes

International Nuclear Information System (INIS)

Yamaguchi, Mami; Anggraini, Sri Ayu; Fujio, Yuki; Breedon, Michael; Plashnitsa, Vladimir V.; Miura, Norio

2012-01-01

A selective and sensitive hydrogen (H 2 ) sensor capable of working at a high operating temperature was developed by using a pair of metal-oxide-based SEs formed on a yttria-stabilized zirconia (YSZ) tube, operating as a mixed-potential type sensor. The utilization of SnO 2 (+30 wt.% YSZ) electrode together with NiO-TiO 2 electrode configured as a combined-type sensor, successfully diminished the response of the examined interfering gases (especially propene), while maintaining high response toward H 2 at an operating temperature of 600 °C under humid operating conditions. The developed sensor exhibited quick response to 100 ppm H 2 , as the 90% response time was observed to be 9 s. The sensing performance of the combined-type sensor was barely affected by changes in water vapor concentration within the range of 1–4 vol.%, suggesting the resilience of the sensor to function in realistic working conditions. This sensor exhibited a linear relationship between sensitivity and H 2 concentration on a logarithmic scale.

Digital implementation of a laser frequency stabilisation technique in the telecommunications band

Science.gov (United States)

Jivan, Pritesh; van Brakel, Adriaan; Manuel, Rodolfo Martínez; Grobler, Michael

2016-02-01

Laser frequency stabilisation in the telecommunications band was realised using the Pound-Drever-Hall (PDH) error signal. The transmission spectrum of the Fabry-Perot cavity was used as opposed to the traditionally used reflected spectrum. A comparison was done using an analogue as well as a digitally implemented system. This study forms part of an initial step towards developing a portable optical time and frequency standard. The frequency discriminator used in the experimental setup was a fibre-based Fabry-Perot etalon. The phase sensitive system made use of the optical heterodyne technique to detect changes in the phase of the system. A lock-in amplifier was used to filter and mix the input signals to generate the error signal. This error signal may then be used to generate a control signal via a PID controller. An error signal was realised at a wavelength of 1556 nm which correlates to an optical frequency of 1.926 THz. An implementation of the analogue PDH technique yielded an error signal with a bandwidth of 6.134 GHz, while a digital implementation yielded a bandwidth of 5.774 GHz.

Synthesis of dense yttrium-stabilised hafnia pellets for nuclear applications by spark plasma sintering

International Nuclear Information System (INIS)

Tyrpekl, Vaclav; Holzhäuser, Michael; Hein, Herwin; Vigier, Jean-Francois; Somers, Joseph; Svora, Petr

2014-01-01

Graphical abstract: Densification of HfO 2 –Y 2 O 3 micro-beads by Spark Plasma Sintering High density pellets with homogenous distribution of Hf and Y serve as neutron absorbers. - Abstract: Dense yttrium–stabilised hafnia pellets (91.35 wt.% HfO 2 and 8.65 wt.% Y 2 O 3 ) were prepared by spark plasma sintering consolidation of micro-beads synthesised by the “external gelation” sol–gel technique. This technique allows a preparation of HfO 2 –Y 2 O 3 beads with homogenous yttria–hafnia solid solution. A sintering time of 5 min at 1600 °C was sufficient to produce high density pellets (over 90% of the theoretical density) with significant reproducibility. The pellets have been machined in a lathe to the correct dimensions for use as neutron absorbers in an experimental test irradiation in the High Flux Reactor (HFR) in Petten, Holland, in order to investigate the safety of americium based nuclear fuels

Flash combustion synthesis and characterisation of nanosized proton conducting Yttria-doped barium cerate

Energy Technology Data Exchange (ETDEWEB)

Jacquin, M.; Jing, Y.; Essoumhi, A.; Taillades, G.; Jones, D.J.; Roziere, J. [Montpellier Univ., Montpellier (France). Lab. des Agregats Moleculaires et Materiaux Inorganiques

2007-10-15

The high conversion efficiency of proton ceramic fuel cells renders them a promising technology for electric power conversion. They also function in an intermediate temperature range (400 to 600 degrees C) where the problem of thermal ageing can be avoided. This paper presented a newly developed flash combustion method for the preparation of proton conducting yttrium-doped barium cerate nanopowders. This quick, safe and low cost route takes advantage of the exothermic and self-sustaining redox reaction between high oxygen content metal salts and a suitable fuel that acts as a reducing agent. The parameters that influence the reaction product are the type of fuel, the fuel to oxidizer ratio, and the ignition temperature. Use of suitable fuel in combustion syntheses ensures stability of the chemical composition and high quality of products, and produces non-toxic gases. In this study, the flash combustion synthesis method was used to ignite the mixture at 600 degrees C. The resulting fine powder was characterized by transmission and scanning electron microscopy, and X-ray diffraction. The resulting nano-sized crystallites allow for the preparation of fully densified materials with densities up to 98 per cent. Water uptake was examined in compressed and sintered samples of BaCe{sub 0.9}Y{sub 0.1}O{sub 2.95} (BCY10). Bulk and total conductivities were determined with impedance spectroscopy in the range 300 to 600 degrees C. Densified yttria doped barium cerate materials show a bulk conductivity of 2.3 x 10{sup -2} S/cm and a total conductivity of 1.2 x 10{sup -2} S/cm at 500 degrees C. The temperature dependence was close to that of the bulk. It was concluded that flash combustion is an interesting alternative method for preparing proton conducting oxides for intermediate temperature fuel cells. 28 refs., 1 tab., 10 figs.

Sewage sludge stabilisation and fertiliser value in a silvopastoral system developed with Eucalyptus nitens Maiden in Lugo (Spain).

Science.gov (United States)

Mosquera-Losada, M R; Ferreiro-Domínguez, N; Daboussi, S; Rigueiro-Rodríguez, A

2016-10-01

Copper (Cu) is one of the heavy metals with highest proportion in sewage sludge. In Europe, sewage sludge should be stabilised before using it as a fertiliser in agriculture. Depending on the stabilisation process, sewage sludge has different Cu contents, and soil Cu incorporation rates. This study was undertaken to examine the effect of fertilisation with different types of sewage sludge (anaerobic, composted, and pelletised) on the concentration of total and available Cu in the soil, the tree growth, the pasture production, and the concentration of Cu in the pasture when compared with control treatments (i.e. no fertilisation and mineral fertilisation) in a silvopastoral system under Eucalyptus nitens Maiden. The results of this experiment show that an improvement of the soil pH increased the incorporation and the mineralisation of the sewage sludge and litter, and therefore, the release of Cu from the soil. Moreover, the concentration of Cu in the pasture and the levels of Cu extracted by the pasture improved when the soil organic matter decreased because the high levels of organic matter in the soil could have formed Cu complex. The composted sewage sludge (COM) increased a) the soil variables studied (pH, total Cu, and available Cu) and b) the Cu extracted by the pasture, both probably due to the higher inputs of cations made with it. In any case, the levels of Cu found in the soil never exceeded the maximums as set by Spanish regulations and did not cause harmful effects on the plants and animals. Therefore, the use of COM as an organic fertiliser should be promoted in silvopastoral systems established in edaphoclimatic conditions similar to this study because COM enhanced the productivity of the system from a viewpoint of the soil and the pasture, without causing any environmental damage. Copyright © 2016 Elsevier B.V. All rights reserved.

Declining and stabilising trends in prevalence of overweight and obesity in Dutch Turkish, Moroccanand South Asian children 3-16 years of age between 1999 and 2011 in the Netherlands

NARCIS (Netherlands)

Wilde, J.A. de; Verkerk, P.H.; Middelkoop, B.J.C.

2014-01-01

Objective: In many developed countries, overweight and obesity prevalence seems to stabilise. The aim of this study was to determine trends between 1999 and 2011 in overweight and obesity prevalence, and mean Body Mass Index (BMI) z-score in Dutch, Turkish, Moroccan and Surinamese South Asian

Charging kinetics in virgin and 1 MeV-electron irradiated yttria-stabilized zirconia in the 300-1000 K range

International Nuclear Information System (INIS)

Thome, T.; Braga, D.; Blaise, G.; Cousty, J.; Pham Van, L.; Costantini, J.M.

2006-01-01

A study performed with a dedicated scanning electron microscope (SEM) on the surface electrical properties of (1 0 0)-oriented yttria-stabilized zirconia (YSZ) single crystals irradiated with 1 MeV electrons is presented. When compared with virgin YSZ, the 1 MeV-irradiated YSZ shows a decrease of the intrinsic total electron emission coefficient σ 0 and an increase of the time constant τ associated with the charging kinetics of the material at room temperature. These measurements performed with the SEM beam at 10 keV indicate that the defects induced by the 1 MeV-electron irradiation generate a positive electric field of the order of 0.5 x 10 6 V/m at a depth of about 1 μm that prevents electrons to escape. When the SEM beam with a 1.1 keV energy is used, a smaller field (∼0.5 x 10 3 V/m) is detected closer to the surface (∼20 nm). The fading of these fields during the thermal annealing in the 400-1000 K temperature range provides information on the nature of defects induced by the 1 MeV-electron irradiation

Secondary recrystallisation in 20 w/o Cr-25 w/o Ni-Nb stabilised stainless steel

International Nuclear Information System (INIS)

Healey, T.; Brown, A.F.; Speight, M.V.

1976-11-01

The fuel cladding material for the Commercial Advanced Gas Reactor is a fine grain 20 w/o Cr-25 w/o Ni niobium stabilised stainless steel. The grain structure stability of this alloy has been investigated as a function of carbon content over the temperature range 930 - 990 0 C. It is demonstrated that the primary grain structure is susceptible to abnormal growth due to secondary recrystallisation of the initial fine grain structure after a composition and temperature dependent incubation period. The magnitude of the incubation period is analysed on the basis that secondary recrystallisation commences when randomly dispersed niobium carbide particles have coarsened to a critical size. The validity of the analysis is tested by comparing the predictions with experimental observation. The model is subsequently used to evaluate the incubation period for conditions of temperature, composition and microstructure which differ from those defined in the experimental studies. (author)

Effect of heat treatment, with and without mechanical work, on the tensile and creep behaviour at 6000C of austenitic stainless steel stabilised with titanium

International Nuclear Information System (INIS)

Padilha, A.F.

1983-01-01

The effect of various heat treatments, with and without mechanical work, on the microstructure and the tensile and creep behaviour at 600 0 C of the titanium stabilised austenitic stainless steel DIN 1.4970, as well as the effects of aging temperature, pre-strain and small boron additions on the creep behaviour of these steels are discussed. The most probable mechanism is suggested. (Author) [pt

The high temperature mechanical characteristics of superplastic 3 mol% yttria stabilized zirconia

International Nuclear Information System (INIS)

Owen, D.M.; Chokshi, A.H.

1998-01-01

A detailed study was undertaken to characterize the deformation behavior of a superplastic 3 mol% yttria-stabilized tetragonal zirconia (3YTZ) over a wide range of strain rates, temperatures and grain sizes. The experimental data were analyzed in terms of the following equation for high temperature deformation: SR ∝ FS n d -p exp(-Q/RT), where SR is the strain rate, FS is the flow stress, d is the grain size, Q is the activation energy, R is the gas constant, T is the absolute temperature, and n and p are constants termed the stress exponent and the inverse grain size exponent, respectively. The experimental data over a wide range of stresses revealed a transition in stress exponent. Deformation in the low and high stress regions was associated with n about 3 and p about 1, and n about 2 and p about 3, respectively. The transition stress between the two regions decreased with increasing grain size. The activation energy was similar for both regions with a value of about 550 kJ/mol. Microstructural measurements revealed that grains remained essentially equiaxed after the accumulation of large strains, and very limited concurrent grain growths occurred in most experiments. Assessment of possible rate controlling creep mechanisms and comparison with previous studied indicate that in the n=2 region, deformation occurs by a grain boundary sliding process whose rate is independent of impurity content. Deformation in the n=3 region is controlled by an interface reaction that is highly sensitive to impurity content. It is concluded that an increase in impurity content increases yttrium segregation to grain boundaries, which enhances the rate of the interface reaction, thereby decreasing the apparent transition stress between the n=2 and n=3 regions. This unified approach incorporating two sequential mechanisms can rationalize many of the apparently dissimilar results that have been reported previously for deformation of 3YTZ

Investigations in the mechanism of carbothermal reduction of yttria stabilized zirconia for ultra-high temperature ceramics application and its influence on yttria contained in it

Science.gov (United States)

Sondhi, Anchal

Zirconium carbide (ZrC) is a high modulus ceramic with an ultra-high melting temperature and, consequently, is capable of withstanding extreme environments. Carbon-carbon composites (CCCs) are important structural materials in current commercial and future hypersonic aircraft; however, these materials may be susceptible to degradation when exposed to elevated temperatures during extreme velocities. At speeds of exceeding Mach 5, intense heating of leading edges of the aircraft triggers rapid oxidation of carbon in CCCs resulting in degradation of the structure and probable failure. Environmental/thermal barrier coatings (EBC/TBC) are employed to protect airfoil structures from extreme conditions. Yttria stabilized zirconia (YSZ) is a well-known EBC/TBC material currently used to protect metallic turbine blades and other aerospace structures. In this work, 3 mol% YSZ has been studied as a potential EBC/TBC on CCCs. However, YSZ is an oxygen conductor and may not sufficiently slow the oxidation of the underlying CCC. Under appropriate conditions, ZrC can form at the interface between CCC and YSZ. Because ZrC is a poor oxygen ion conductor in addition to its stability at high temperatures, it can reduce the oxygen transport to the CCC and thus increase the service lifetime of the structure. This dissertation investigates the thermodynamics and kinetics of the YSZ/ZrC/CCC system and the resulting structural changes across multiple size scales. A series of experiments were conducted to understand the mechanisms and species involved in the carbothermal reduction of ZrO2 to form ZrC. 3 mol% YSZ and graphite powders were uniaxially pressed into pellets and reacted in a graphite (C) furnace. Rietveld x-ray diffraction phase quantification determined that greater fractions of ZrC were formed when carbon was the majority mobile species. These results were validated by modeling the process thermochemically and were confirmed with additional experiments. Measurements were

Fabrication and characterization of chromium-doped nanophase separated yttria-alumina-silica glass-based optical fibers

Energy Technology Data Exchange (ETDEWEB)

Dutta, Debjit; Dhar, Anirban; Das, Shyamal; Paul, Mukul C. [Fiber Optics and Photonics Division, CSIR-Central Glass and Ceramic Research Institute, Kolkata (India); Kir' yanov, Alexander V. [Centro de Investigaciones en Optica, Guanajuato (Mexico); Bysakh, Sandip [Electron Microscopic Section, Material Characterization Division, CSIR-Central Glass and Ceramic Research Institute, Kolkata (India)

2015-08-15

The basic material and optical properties of chromium-doped nanophase-separated yttria-alumina-silica (YAS) glass based optical preforms and fibers, fabricated through the modified chemical vapor deposition process in conjunction with solution doping technique under suitable thermal annealing conditions are reported. The size of the phase-separated particles within the core of the annealed preform is around 20-30 nm which is significantly reduced to around 5.0 nm in the drawn fiber. The absorption spectra of fibers drawn from the annealed and non-annealed preform samples revealed the presence of Cr{sup 4+}, Cr{sup 3+}, and Cr{sup 6+} specie. Numerically, extinction of absorption drops ∝3-3.5 times for the annealed sample as a result of nano-phase restructuration during annealing process. Intense broadband emission (within 500-800 nm) in case of the annealed preform sample is observed as compared to the non-annealed one and is associated with the presence of Cr{sup 3+} ions in nanostructured environment inside the YAS core glass. The final fibers show broadband emission ranging from 900 to 1400 nm under pumping at 1064 nm which is attributed mainly to the presence of Cr{sup 3+}/Cr{sup 4+} ions. The fabricated fibers seem to be a potential candidate for the development of fiber laser sources for the visible and near-infra ranges and for effective Q-switching units for ∝1-1.1 μm all-fiber ytterbium lasers. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Characterization of the yttria-stabilized zirconia thin film electrophoretic deposited on La0.8Sr0.2MnO3 substrate

International Nuclear Information System (INIS)

Yang, Koho; Shen, Jung-Hsiung; Yang, Kai-Yun; Hung, I-Ming; Fung, Kuan-Zong; Wang, Moo-Chin

2007-01-01

The yttria-stabilized zirconia (YSZ) thin films electrophoretic deposited on the La 0.8 Sr 0.2 MnO 3 (LSM) substrate have been characterized by using zeta potential analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The La 2 Zr 2 O 7 (LZ) formed at the interface between the YSZ thin film and LSM substrate, after sintered at 1400 o C for 52 h, are identified by XRD. The zeta potential of the YSZ particles in pure ethanol-acetone is about 7.8 mV, but when the I 2 concentration is greater than 0.6 g/1, the zeta potential attains a constant value, 46 mV. The relation between deposit weight of the YSZ films and the applied voltage shows a non-linear behavior. Thickness of the YSZ thin film deposited on the LSM substrate by electrophoretic deposition is controlled by a diffusion process. A larger LZ with the thickness of 200 nm is formed at the interface between the YSZ film and the LSM substrate

Recurrent Partial Words

Directory of Open Access Journals (Sweden)

Francine Blanchet-Sadri

2011-08-01

Full Text Available Partial words are sequences over a finite alphabet that may contain wildcard symbols, called holes, which match or are compatible with all letters; partial words without holes are said to be full words (or simply words. Given an infinite partial word w, the number of distinct full words over the alphabet that are compatible with factors of w of length n, called subwords of w, refers to a measure of complexity of infinite partial words so-called subword complexity. This measure is of particular interest because we can construct partial words with subword complexities not achievable by full words. In this paper, we consider the notion of recurrence over infinite partial words, that is, we study whether all of the finite subwords of a given infinite partial word appear infinitely often, and we establish connections between subword complexity and recurrence in this more general framework.

Electronic, structural, and optical properties of crystalline yttria

International Nuclear Information System (INIS)

Xu, Y.; Gu, Z.; Ching, W.Y.

1997-01-01

The electronic structure of crystalline Y 2 O 3 is investigated by first-principles calculations within the local-density approximation (LDA) of the density-functional theory. Results are presented for the band structure, the total density of states (DOS), the atom- and orbital-resolved partial DOS, effective charges, bond order, and charge-density distributions. Partial covalent character in the Y-O bonding is shown, and the nonequivalency of the two Y sites is demonstrated. The calculated electronic structure is compared with a variety of available experimental data. The total energy of the crystal is calculated as a function of crystal volume. A bulk modulus B of 183 Gpa and a pressure coefficient B ' of 4.01 are obtained, which are in good agreement with compression data. An LDA band gap of 4.54 eV at Γ is obtained which increases with pressure at a rate of dE g /dP=0.012eV/Gpa at the equilibrium volume. Also investigated are the optical properties of Y 2 O 3 up to a photon energy of 20 eV. The calculated complex dielectric function and electron-energy-loss function are in good agreement with experimental data. A static dielectric constant of var-epsilon(0)=3.20 is obtained. It is also found that the bottom of the conduction band consists of a single band, and direct optical transition at Γ between the top of the valence band and the bottom of the conduction band may be symmetry forbidden. copyright 1997 The American Physical Society

Shape stabilised phase change materials (SSPCMs): High density polyethylene and hydrocarbon waxes

Energy Technology Data Exchange (ETDEWEB)

Mu, Mulan, E-mail: mmu01@qub.ac.uk, E-mail: m.basheer@qub.ac.uk; Basheer, P. A. M., E-mail: mmu01@qub.ac.uk, E-mail: m.basheer@qub.ac.uk [School of Planning, Architecture and Civil Engineering, Queen' s University Belfast, BT9 5AG (United Kingdom); Bai, Yun, E-mail: yun.bai@ucl.ac.uk [Department of Civil, Environmental and Geomatic Engineering, University College London, WC1E 6BT (United Kingdom); McNally, Tony, E-mail: t.mcnally@warwick.ac.uk [WMG, University of Warwick, CV4 7AL (United Kingdom)

2014-05-15

Shape stabilised phase change materials (SSPCMs) based on high density polyethylene (HDPE) with high (HPW, T{sub m}=56-58 °C) and low (L-PW, T{sub m}=18-23 °C) melting point waxes were prepared by melt-mixing in a twin-screw extruder and their potential in latent heat thermal energy storage (LHTES) applications for housing assessed. The structure and morphology of these blends were investigated by scanning electron microscopy (SEM). Both H-PW and L-PW were uniformly distributed throughout the HDPE matrix. The melting point and latent heat of the SSPCMs were determined by differential scanning calorimetry (DSC). The results demonstrated that both H-PW and L-PW have a plasticisation effect on the HDPE matrix. The tensile and flexural properties of the samples were measured at room temperature (RT, 20±2 °C) and 70 °C, respectively. All mechanical properties of HDPE/H-PW and HDPE/L-PW blends decreased from RT to 70 °C. In all instances at RT, modulus and stress, irrespective of the mode of deformation was greater for the HDPE/H-PW blends. However, at 70 °C, there was no significant difference in mechanical properties between the HDPE/H-PW and HDPE/L-PW blends.

Deformations, moduli stabilisation and gauge couplings at one-loop

Energy Technology Data Exchange (ETDEWEB)

Honecker, Gabriele; Koltermann, Isabel [PRISMA Cluster of Excellence, MITP & Institut für Physik (WA THEP),Johannes Gutenberg-Universität,Staudingerweg 9, 55128 Mainz (Germany); Staessens, Wieland [Instituto de Física Teórica UAM-CSIC, Universidad Autónoma de Madrid Cantoblanco,Calle de Nicolás Cabrera 13-15, 28049 Madrid (Spain); Departamento de Física Teórica, Universidad Autónoma de Madrid Cantoblanco,Calle de Nicolás Cabrera 13-15, 28049 Madrid (Spain)

2017-04-05

We investigate deformations of ℤ{sub 2} orbifold singularities on the toroidal orbifold T{sup 6}/(ℤ{sub 2}×ℤ{sub 6}) with discrete torsion in the framework of Type IIA orientifold model building with intersecting D6-branes wrapping special Lagrangian cycles. To this aim, we employ the hypersurface formalism developed previously for the orbifold T{sup 6}/(ℤ{sub 2}×ℤ{sub 2}) with discrete torsion and adapt it to the (ℤ{sub 2}×ℤ{sub 6}×ΩR) point group by modding out the remaining ℤ{sub 3} subsymmetry and the orientifold projection ΩR. We first study the local behaviour of the ℤ{sub 3}×ΩR invariant deformation orbits under non-zero deformation and then develop methods to assess the deformation effects on the fractional three-cycle volumes globally. We confirm that D6-branes supporting USp(2N) or SO(2N) gauge groups do not constrain any deformation, while deformation parameters associated to cycles wrapped by D6-branes with U(N) gauge groups are constrained by D-term supersymmetry breaking. These features are exposed in global prototype MSSM, Left-Right symmetric and Pati-Salam models first constructed in (DOI: 10.1016/j.nuclphysb.2015.10.009; 10.1002/prop.201400066), for which we here count the number of stabilised moduli and study flat directions changing the values of some gauge couplings. Finally, we confront the behaviour of tree-level gauge couplings under non-vanishing deformations along flat directions with the one-loop gauge threshold corrections at the orbifold point and discuss phenomenological implications, in particular on possible LARGE volume scenarios and the corresponding value of the string scale M{sub string}, for the same global D6-brane models.

Influence of creep and cyclic oxidation in thermal barrier coatings

Energy Technology Data Exchange (ETDEWEB)

Seiler, Philipp; Baeker, Martin; Roesler, Joachim [Technische Univ. Braunschweig (Germany). Inst. fuer Werkstoffe

2012-01-15

The lifetime of thermal barrier coating systems is limited by cracks close to the interfaces, causing delamination. To study the failure mechanisms, a simplified model system is analysed which consists of a bond-coat bulk material, a thermally grown oxide, and an yttria-stabilised zirconia topcoat. The stresses in the model system are calculated using a finite element model which covers the simulation of full thermal cycles, creep in all layers, and the anisotropic oxidation during dwelling. Creep in the oxide and the thermal barrier coating is varied with the use of different creep parameter sets. The influence of creep in the bondcoat is analysed by using two different bond-coat materials: fast creeping Fecralloy and slow creeping oxide dispersion strengthened MA956. It is shown that creep in the bondcoat influences the lifetime of the coatings. Furthermore, a fast creeping thermally grown oxide benefits the lifetime of the coating system. (orig.)

Excimer pulsed laser deposition and annealing of YSZ nanometric films on Si substrates

International Nuclear Information System (INIS)

Caricato, A.P.; Barucca, G.; Di Cristoforo, A.; Leggieri, G.; Luches, A.; Majni, G.; Martino, M.; Mengucci, P.

2005-01-01

We report experimental results obtained for electrical and structural characteristics of yttria-stabilised zirconia (YSZ) thin films deposited by pulsed laser deposition (PLD) on Si substrates at room temperature. Some samples were submitted to thermal treatments in different ambient atmospheres (vacuum, N 2 and O 2 ) at a moderate temperature. The effects of thermal treatments on the film electrical properties were studied by C-V and I-V measurements. Structural characteristics were obtained by X-ray diffraction (XRD), X-ray reflectivity (XRR) and transmission electron microscopy (TEM) analyses. The as-deposited film was amorphous with an in-depth non-uniform density. The annealed films became polycrystalline with a more uniform density. The sample annealed in O 2 was uniform over all the thickness. Electrical characterisation showed large hysteresis, high leakage current and positive charges trapped in the oxide in the as-deposited film. Post-deposition annealing, especially in O 2 atmosphere, improved considerably the electrical properties of the films

Mechanical characterisation at nanometric scale of a new design of SOFCs

Energy Technology Data Exchange (ETDEWEB)

Roa, J.J.; Morales, M.; Segarra, M. [Department of Materials Science and Metallurgical Engineering, University of Barcelona, 08028 Barcelona (Spain); Ruiz-Morales, J.C.; Nunez, P. [Department of Inorganic Chemistry, University of La Laguna, 38200 Tenerife (Spain); Canales-Vazquez, J. [Renewable Energies Research Institute, Albacete Science and Technology Park, University of Castilla la Mancha, 02006 Albacete (Spain); G Capdevila, X. [Centre of Design and Optimisation of Processes and Materials, Parc Cientific of Barcelona, 08028 Barcelona (Spain)

2011-02-15

The mechanical stability is an important parameter to gain knowledge in the potential applications of a novel design of electrolyte-supported SOFC, based on yttria-stabilised zirconia (YSZ) and NiO-YSZ composites, with cross-linked channels ({proportional_to}90 {mu}m of diameter). In this experimental work, the mechanical properties (hardness, H and Young's modulus, E) at different applied loads have been studied using the nanoindentation technique and the equivalent indenter method. On the other hand, the different fracture mechanisms have been determined using atomic force microscopy (AFM), observing the plastic behaviour that takes place during the indentation process. H value for YSZ is higher than that for NiO-YSZ, while E values for YSZ and NiO-YSZ are 260 {+-} 15 and 205 {+-} 20 GPa, respectively. Only YSZ samples present several radial cracks at the corners nucleated by sharp indentation, thus indicating that H values have been underestimated. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Studies of the Stabilization of Superconductor Coils; Etudes sur la Stabilisation des Bobines Supraconductrices

Energy Technology Data Exchange (ETDEWEB)

Donadieu, L.; Maldy, J. [Compagnie Generale d' Electricite Marcoussis (France)

1966-12-15

operation of the coil will be stable and the passage of the I-B characteristic of the material will be reversible; (b) Ic < Im, the operation of the coil is unstable and any sufficiently large disturbances (flux jump, movement of windings, etc. ) can produce blocking. This is inevitably the case with the large coils whose operational limit tends towards Im. Different coils have been constructed with more or leas stabilised materials and the results of tests on them are analysed as a' function of the previous theories. There Is a full discussion of the advantages and disadvantages of coil stabilizations. (author) [French] La stabilisation de l'intensite du courant dans les bobinages supra-conducteurs, qui apparait d'une importance capitale pour la construction de bobinages de grande taille , est etudiee a la fois du point de vue theorique et du point de vue experiment a l. L'etude de la dynamique de la transition d'un supraconducteur transportant du courant, entre l ' e t at supraconducteur a resistance nulle et l ' e tat a resistance normale ( l e blocage), revele l'existence d'une intensite caracteristique, Im, pour laquelle la vitesse de propagation de la region normale est nulle. Cette intensite depend directement des echanges de chaleur entre le supraconducteur et le milieu ambiant, et de la resistance du materiau a l ' e t a t normal; Im depend indirectement de l'intensite du champ magnetique. Si un supraconducteur est utilise avec une intensite de courant inferieure a Im, la vitesse de propagation est negative et le supraconducteur est capable eventuellement de realiser la transition inverse de l ' e t a t normal a l ' e t a t supraconducteur. On peut montrer que pour une intensite Is telle que Is = Im/ Square-Root 2 , la vitesse de propagation qui est negative devient infiniment grande. L'existence de ces 2 intensites caracteristiques permet de distinguer trois cas de comportement differents selon l'intensite du courant qui parcourt le supraconducteur. L'auteur a

Degradation of conductivity and microstructure under thermal and current load in Ni-YSZ cermets for SOFC anodes

DEFF Research Database (Denmark)

Thydén, Karl Tor Sune; Barfod, Rasmus; Liu, Yi-Lin

2006-01-01

The degradation of electrical conductivity in porous nickel-yttria stabilized zirconia composite cermets in a H2/H2O atmosphere under high temperature treatments has been investigated. The parameters varied were: temperature, water partial pressure, and electrical current load. The microstructure...... fraction of percolated Ni was measured. Temperature proved to have the largest effect on the degradation. Samples tested at 1000°C, in contrast to 750°C, showed a severe decrease of conductivity and growth of Ni particles. Higher water partial pressure accelerated Ni particle growth at both temperatures......, but the loss of percolation and conductivity at 1000°C was less severe under high water partial pressure. A possible explanation for this behavior is discussed....

Effects of whitening dentifrice on yttria-stabilized tetragonal zirconia polycrystal surfaces after simulating brushing.

Science.gov (United States)

Pinelli, Lígia Antunes Pereira; Gimenes Olbera, Amanda Caroline; Candido, Lucas Miguel; Miotto, Larissa Natiele; Antonio, Selma Gutierrez; Fais, Laiza Maria Grassi

2017-01-01

The changes that occur after brushing yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) are unknown. These changes may favor the retention of microorganisms and chemisorption of water, impairing its longevity. The purpose of this in vitro study was to evaluate the effects of a whitening dentifrice on Y-TZP surfaces after simulating 10 years of brushing. Seventy-two bar-shaped specimens (20×4×1.2 mm) were divided into 4 groups: storage in distilled water (SW, control), brushing with distilled water (BW), brushing with dentifrice (BD), and brushing with whitening dentifrice (BWD). Brushing was conducted using a linear brushing machine (878400 cycles, 0.98 N, soft toothbrush). The mean roughness (Ra) was analyzed with a profilometer and the superficial topography with scanning electron microscopy (SEM) at baseline and after treatment. Crystalline phases were characterized using x-ray diffraction. Baseline and posttreatment Ra were analyzed using the 1-way ANOVA and Tukey HSD multiple comparison test; the paired t test was used for intragroup comparison (all α=.05). The Ra (μm) means (before/after treatment) were SW 0.28/0.28; BW 0.32/0.31; BD 0.28/0.36; BWD 0.30/0.20. No statistically significant difference was found for Ra at baseline (P=.108) than for posttreatment results (P<.001); the BD group had higher Ra values when compared with baseline (P=.019); the BWD group had the lowest values (P<.001). The BD surfaces showed pronounced scratches and detachment of the surface, while BWD showed smoother surfaces; similar crystallographic results among groups were observed. Brushing Y-TZP with conventional dentifrice increased roughness, while brushing with whitening dentifrice reduced roughness. Neither dentifrice changed the crystallographic phases after brushing. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Assessing the feasibility of yttria-stabilized zirconia in novel designs as mandibular anterior fixed lingual retention following orthodontic treatment

Science.gov (United States)

Stout, Matthew

The purpose of this study is to explore the feasibility of yttria-stabilized zirconia (Y-TZP) in fixed lingual retention as an alternative to stainless steel. Exploratory Y-TZP specimens were milled to establish design parameters. Next, specimens were milled according to ASTM standard C1161-13 and subjected to four-point flexural test to determine materials properties. Finite Element (FE) Analysis was employed to evaluate nine novel cross-sectional designs and compared to stainless steel wire. Each design was analyzed under the loading conditions to determine von Mises and bond stress. The most promising design was fabricated to assess accuracy and precision of current CAD/CAM milling technology. The superior design had a 1.0 x 0.5 mm semi-elliptical cross section and was shown to be fabricated reliably. Overall, the milling indicated a maximum percent standard deviation of 9.3 and maximum percent error of 13.5 with a cost of $30 per specimen. Y-TZP can be reliably milled to dimensions comparable to currently available metallic retainer wires. Further research is necessary to determine the success of bonding protocol and clinical longevity of Y-TZP fixed retainers. Advanced technology is necessary to connect the intraoral scan to an aesthetic and patient-specific Y-TZP fixed retainer.

On the use of the stabilised Q1P0 element for geodynamical simulations and why this is a bad choice for buyoancy-driven flows.

Science.gov (United States)

Thieulot, Cedric

2016-04-01

Many Finite Element geodynamical codes (Fullsack,1995; Zhong et al., 2000; Thieulot, 2011) are based on bi/tri­-linear velocity constant pressure element (commonly called Q1P0), because of its ease of programming and rather low memory footprint, despite the presence of (pressure) checker­board modes. However, it is long known that the Q1P0 is not inf­-sup stable and does not lend itself to the use of iterative solvers, which makes it a less­ than­ ideal candidate for high resolution 3D models. Other attempts were made more recently (Burstedde et al., 2013; Le Pourhiet et al., 2012) with the use of the stabilised Q1Q1 element (bi/tri­-linear velocity and pressure). This element, while also attractive from an implementation and memory standpoint, suffers a major drawback due to the artificial compressibility introduced by the polynomial projection stabilization. These observations have shifted part of the community towards the Finite Difference Method while the remaining part is now embracing inf­sup stable second­ order elements [May et al., 2015; Kronbichler,2012). Rather surprinsingly, a third option exists when it comes to first ­order elements in the form of the stabilised Q1P0 element, but virtually no literature exists concerning its use for geodynamical applications. I will then recall the specificity of the stabilisation and will carry out a series of benchmark experiments and geodynamical tests to assess its performance. While being shown to work as expected in benchmark experiments, the stabilised Q1P0 element turns out to introduce first-order numerical artefacts in the velocity and pressure solutions in the case of buoyancy-driven flows. Burstedde, C., Stadler, G., Alisic, L., Wilcox, L. C., Tan, E., Gurnis, M., & Ghattas, O. (2013). Large­scale adaptive mantle convection simulation. Geophysical Journal International, 192(3), 889­906. Fullsack, P. (1995). An arbitrary Lagrangian­Eulerian formulation for creeping flows and its application in

Obtention of zirconia films stabilized with Yttria via pyrolysis spray: study of the solvent influence; Obtencao de filmes de zirconia estabilizada com itria via spray pirolise: estudo da influencia do solvente

Energy Technology Data Exchange (ETDEWEB)

Halmenschlager, Cibele Melo; Vieira, Ramaugusto da Porciuncula; Takimi, Antonio Shigueaki; Bergmann, Carlos Perez; Silva, Aline Lima da; Malfatti, Celia de Fraga [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais (PPGEM). Lab. de Materiais Ceramicos (LACER)]. E-mail: cibelemh@yahoo.com.br

2008-07-01

Yttria-stabilized-zirconia (YSZ) has been object of many studies, due to its great chemical stability and excellent ionic conduction in high temperature. This material has been studies with an intention of to be used with electrolyte of oxide solid fuel cells, which work in high temperature. The aim of the present work was to evaluate the influence of the solvent on the elaboration of crystalline films of YSZ via spray pyrolysis. The film was prepared by spray pyrolysis with zirconium acetylacetonate (Zr(C{sub 6}H{sub 7}O{sub 2}){sub 4}) and yttrium chloride (YCl{sub 3}.6H{sub 2}O), dissolved in different solvents: ethanol (C{sub 2}H{sub 6}O), ethanol (C{sub 2}H{sub 6}O) + propyleneglycol (C{sub 3}H{sub 8}O{sub 2}) with volume ratio (1:1) and ethanol (C{sub 2}H{sub 6}O) + diethylene glycol butyl ether (C{sub 8}H{sub 18}O{sub 3}) with volume ratio of 1:1. A disk of steel 316L was used as substrate. The amorphous film was deposited in the substrate heated at 280 deg C {+-} 50 deg C. After deposition from thermal treatment at 700 deg C the amorphous film was changed into Yttria-stabilized-zirconia film. The thermal behavior of the films has been studied by both (DTA/TGA) thermogravimetric and mass spectroscopy analyses. The morphology and crystalline phase of the films was investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The YSZ film obtained after heat treatment was dense and crystalline, however, the analyses indicate a significant influence of the solvent and of the substrate temperature during the deposition process on the film morphology.(author)

Effect of autoclave induced low-temperature degradation on the adhesion energy between yttria-stabilized zirconia veneered with porcelain.

Science.gov (United States)

Li, Kai Chun; Waddell, J Neil; Prior, David J; Ting, Stephanie; Girvan, Liz; van Vuuren, Ludwig Jansen; Swain, Michael V

2013-11-01

To investigate the effect of autoclave induced low-temperature degradation on the adhesion energy between yttria-stabilized zirconia veneered with porcelain. The strain energy release rate using a four-point bending stable fracture test was evaluated for two different porcelains [leucite containing (VM9) and glass (Zirox) porcelain] veneered to zirconia. Prior to veneering the zirconia had been subjected to 0 (control), 1, 5, 10 and 20 autoclave cycles. The specimens were manufactured to a total bi-layer dimension of 30 mm × 8 mm × 3 mm. Subsequent scanning electron microscopy/energy dispersive spectrometry, electron backscatter diffraction and X-ray diffraction analysis were performed to identify the phase transformation and fracture behavior. The strain energy release rate for debonding of the VM9 specimens were significantly higher (pautoclave cycles lowered the strain energy release rate significantly (pautoclave cycles between 5 and 20. The monoclinic phase reverted back to tetragonal phase after undergoing conventional porcelain firing cycles. EBSD data showed significant changes of the grain size distribution between the control and autoclaved specimen (cycle 20). Increasing autoclave cycles only significantly decreased the adhesion of the VM9 layered specimens. In addition, a conventional porcelain firing schedule completely reverted the monoclinic phase back to tetragonal. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Partial tooth gear bearings

Science.gov (United States)

Vranish, John M. (Inventor)

2010-01-01

A partial gear bearing including an upper half, comprising peak partial teeth, and a lower, or bottom, half, comprising valley partial teeth. The upper half also has an integrated roller section between each of the peak partial teeth with a radius equal to the gear pitch radius of the radially outwardly extending peak partial teeth. Conversely, the lower half has an integrated roller section between each of the valley half teeth with a radius also equal to the gear pitch radius of the peak partial teeth. The valley partial teeth extend radially inwardly from its roller section. The peak and valley partial teeth are exactly out of phase with each other, as are the roller sections of the upper and lower halves. Essentially, the end roller bearing of the typical gear bearing has been integrated into the normal gear tooth pattern.

Advanced homogenization strategies in material modeling of thermally sprayed TBCs

International Nuclear Information System (INIS)

Bobzin, K.; Lugscheider, E.; Nickel, R.; Kashko, T.

2006-01-01

Thermal barrier coatings (TBC), obtained by atmospheric plasma spraying (APS), have a complex microstructure (lamellar, porous, micro-cracked). Process parameters take an influence on this microstructure. Two methods based on the homogenization for periodic structures are presented in this article. The methods are used to calculate the effective material behavior of APS-TBCs made of partially yttria stabilized zirconia (PYSZ) depending on the microstructure. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Laser frequency stabilisation by the Pound - Drever - Hall method using an acousto-optic phase modulator operating in the pure Raman - Nath diffraction regime

International Nuclear Information System (INIS)

Baryshev, Vyacheslav N

2012-01-01

Frequency stabilisation of diode laser radiation has been implemented by the Pound - Drever - Hall method using a new acousto-optic phase modulator, operating in the pure Raman - Nath diffraction regime. It is experimentally shown that, as in the case of saturated-absorption spectroscopy in atomic vapour, the spatial divergence of the frequency-modulated output spectrum of this modulator does not interfere with obtaining error signals by means of heterodyne frequency-modulation spectroscopy with a frequency discriminator based on a high-Q Fabry - Perot cavity with finesse of several tens of thousands.

Crystallization kinetics and growth mechanism of 8 mol% yttria-stabilized zirconia (8YSZ) nano-powders prepared by a sol-gel process

International Nuclear Information System (INIS)

Kuo, C.-W.; Lee, Y.-H.; Hung, I-M.; Wang, M.-C.; Wen, S.-B.; Fung, K.-Z.; Shih, C.-J.

2008-01-01

Eight mol% yttria-stabilized zirconia (8YSZ) gel powders were synthesized at 348 K for 2 h using ZrOCl 2 .8H 2 O and Y(NO 3 ) 3 .6H 2 O as starting materials in an ethanol-water solution by a sol-gel process. The crystallization kinetics and growth mechanism of the 8YSZ gel powders have been investigated using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and selected area electron diffraction (SAED). The XRD results and SAED pattern show that the 8YSZ gel powders calcined at 773 K for 2 h is a cubic ZrO 2 . The activation energy for the crystallization of the cubic ZrO 2 formation in the 8YSZ gel powders is determined as 231.76 kJ/mol by a non-isothermal DTA method. Both growth morphology parameter (n) and crystallization mechanism index (m) are close to 3.0, indicating that the bulk nucleation is dominant in the cubic ZrO 2 formation. The TEM examination shows that the cubic ZrO 2 has a spherical-like morphology with a size ranging from 10 to 20 nm

A non-linear optimal Discontinuous Petrov-Galerkin method for stabilising the solution of the transport equation

International Nuclear Information System (INIS)

Merton, S. R.; Smedley-Stevenson, R. P.; Pain, C. C.; Buchan, A. G.; Eaton, M. D.

2009-01-01

This paper describes a new Non-Linear Discontinuous Petrov-Galerkin (NDPG) method and application to the one-speed Boltzmann Transport Equation (BTE) for space-time problems. The purpose of the method is to remove unwanted oscillations in the transport solution which occur in the vicinity of sharp flux gradients, while improving computational efficiency and numerical accuracy. This is achieved by applying artificial dissipation in the solution gradient direction, internal to an element using a novel finite element (FE) Riemann approach. The amount of dissipation added acts internal to each element. This is done using a gradient-informed scaling of the advection velocities in the stabilisation term. This makes the method in its most general form non-linear. The method is designed to be independent of angular expansion framework. This is demonstrated for the both discrete ordinates (S N ) and spherical harmonics (P N ) descriptions of the angular variable. Results show the scheme performs consistently well in demanding time dependent and multi-dimensional radiation transport problems. (authors)

New mesostructured organosilica with chiral sugar derived structures: nice host for gold nanoparticles stabilisation.

Science.gov (United States)

Hérault, Damien; Cerveau, Geneviève; Corriu, Robert J P; Mehdi, Ahmad

2011-01-14

In this paper we describe the synthesis of functionalised mesoporous organosilicas containing a mannitol derivative in the framework. For this purpose, a bis-silylated precursor 3,4-Di-O-[3-(triethoxysilylpropyl)carbamate]-1,2:5,6-di-O-isopropylidene-D-mannitol was prepared by coupling of 1,2:5,6-di-O-isopropylidene-D-mannitol with 3-(triethoxysilylpropyl)isocyanate. The framework-functionalised materials were obtained in one step by the "direct synthesis" method which consists of a co-hydrolysis and polycondensation of a bis-silylated mannitol precursor with tetraethylorthosilicate (TEOS) in the presence of a non-ionic triblock co-polymer (P123) as structure-directing agent. Interestingly, deprotection of the 1,2,5,6 OH functional groups occurred during the material synthesis. The obtained solids were characterized by (13)C and (29)Si CP-MAS NMR, N(2) adsorption-desorption, powder X-ray diffraction, TEM and elemental analysis. We have shown that, the OH functional groups, which are released during the synthesis of the mesoporous silica, can be used for chelation of ions and stabilisation of nanoparticles. The subsequent growth of gold (0) nanoparticles in the wall has been investigated and evidenced.

The 2.1 Å resolution structure of cyanopindolol-bound β1-adrenoceptor identifies an intramembrane Na+ ion that stabilises the ligand-free receptor.

Directory of Open Access Journals (Sweden)

Jennifer L Miller-Gallacher

Full Text Available The β1-adrenoceptor (β1AR is a G protein-coupled receptor (GPCR that is activated by the endogenous agonists adrenaline and noradrenaline. We have determined the structure of an ultra-thermostable β1AR mutant bound to the weak partial agonist cyanopindolol to 2.1 Å resolution. High-quality crystals (100 μm plates were grown in lipidic cubic phase without the assistance of a T4 lysozyme or BRIL fusion in cytoplasmic loop 3, which is commonly employed for GPCR crystallisation. An intramembrane Na+ ion was identified co-ordinated to Asp872.50, Ser1283.39 and 3 water molecules, which is part of a more extensive network of water molecules in a cavity formed between transmembrane helices 1, 2, 3, 6 and 7. Remarkably, this water network and Na+ ion is highly conserved between β1AR and the adenosine A2A receptor (rmsd of 0.3 Å, despite an overall rmsd of 2.4 Å for all Cα atoms and only 23% amino acid identity in the transmembrane regions. The affinity of agonist binding and nanobody Nb80 binding to β1AR is unaffected by Na+ ions, but the stability of the receptor is decreased by 7.5°C in the absence of Na+. Mutation of amino acid side chains that are involved in the co-ordination of either Na+ or water molecules in the network decreases the stability of β1AR by 5-10°C. The data suggest that the intramembrane Na+ and associated water network stabilise the ligand-free state of β1AR, but still permits the receptor to form the activated state which involves the collapse of the Na+ binding pocket on agonist binding.

Preparation of epitaxial YBa2Cu3O7-y films on CeO2-buffered yttria-stabilized zirconia substrates by fluorine-free metalorganic deposition

International Nuclear Information System (INIS)

Tsukada, Kenichi; Yamaguchi, Iwao; Sohma, Mitsugu; Kondo, Wakichi; Kamiya, Kunio; Kumagai, Toshiya; Manabe, Takaaki

2007-01-01

Epitaxial YBa 2 Cu 3 O 7-y (YBCO) films of 120-550 nm thickness have been prepared by fluorine-free metalorganic deposition using a metal acetylacetonate-based coating solution on yttria-stabilized zirconia (YSZ) substrates with an evaporated CeO 2 buffer layer. The YBCO films were highly (0 0 1)-oriented by X-ray diffraction θ-2θ scanning and φ scanning. The YBCO films 120-400 nm in thickness demonstrated high critical current densities (J c ) with an average in excess of 3 MA/cm 2 at 77 K using an inductive method. In particular, a 210-nm-thick film showed a J c of 4.5 MA/cm 2 . These excellent properties are attributed to the high crystallinity, small in-plane fluctuation due to high epitaxy and to the microstructure free from grain boundaries in the YBCO films. Further increase of film thickness increased the fraction of irregularities, i.e., precipitates and micropores, in the film surfaces, resulting in lower J c values

Immobilisation of heavy metal in cement-based solidification/stabilisation: A review

International Nuclear Information System (INIS)

Chen, Q.Y.; Tyrer, M.; Hills, C.D.; Yang, X.M.; Carey, P.

2009-01-01

Heavy metal-bearing waste usually needs solidification/stabilization (s/s) prior to landfill to lower the leaching rate. Cement is the most adaptable binder currently available for the immobilisation of heavy metals. The selection of cements and operating parameters depends upon an understanding of chemistry of the system. This paper discusses interactions of heavy metals and cement phases in the solidification/stabilisation process. It provides a clarification of heavy metal effects on cement hydration. According to the decomposition rate of minerals, heavy metals accelerate the hydration of tricalcium silicate (C 3 S) and Portland cement, although they retard the precipitation of portlandite due to the reduction of pH resulted from hydrolyses of heavy metal ions. The chemical mechanism relevant to the accelerating effect of heavy metals is considered to be H + attacks on cement phases and the precipitation of calcium heavy metal double hydroxides, which consumes calcium ions and then promotes the decomposition of C 3 S. In this work, molecular models of calcium silicate hydrate gel are presented based on the examination of 29 Si solid-state magic angle spinning/nuclear magnetic resonance (MAS/NMR). This paper also reviews immobilisation mechanisms of heavy metals in hydrated cement matrices, focusing on the sorption, precipitation and chemical incorporation of cement hydration products. It is concluded that further research on the phase development during cement hydration in the presence of heavy metals and thermodynamic modelling is needed to improve effectiveness of cement-based s/s and extend this waste management technique

Experts' understanding of partial derivatives using the Partial Derivative Machine

OpenAIRE

Roundy, David; Dorko, Allison; Dray, Tevian; Manogue, Corinne A.; Weber, Eric

2014-01-01

Partial derivatives are used in a variety of different ways within physics. Most notably, thermodynamics uses partial derivatives in ways that students often find confusing. As part of a collaboration with mathematics faculty, we are at the beginning of a study of the teaching of partial derivatives, a goal of better aligning the teaching of multivariable calculus with the needs of students in STEM disciplines. As a part of this project, we have performed a pilot study of expert understanding...

Microstructure and phase composition of sputter-deposited zirconia-yttria films

International Nuclear Information System (INIS)

Knoll, R.W.; Bradley, E.R.

1983-11-01

Thin ZrO 2 -Y 2 O 3 coatings ranging in composition from 3 to 15 mole % Y 2 O 3 were produced by rf sputter deposition. This composition range spanned the region on the equilibrium ZrO 2 -Y 2 O 3 phase diagram corresponding to partially stabilized zirconia (a mixture of tetragonal ZrO 2 and cubic solid solution). Microstructural characteristics and crystalline phase composition of as-deposited and heat treated films (1100 0 C and 1500 0 C) were determined by transmission electron microscopy (TEM) and by x-ray diffraction (XRD). Effects of substrate bias (0 approx. 250 volts), which induced ion bombardment of the film during growth, were also studied. The as-deposited ZrO 2 -Y 2 O 3 films were single phase over the composition range studied, and XRD data indicated considerable local atomic disorder in the lattice. Films produced at low bias contained intergranular voids, pronounced columnar growth, and porosity between columns. At high bias, the microstructure was denser, and films contained high compressive stress. After heat treatment, all deposits remained single phase, therefore a microstructure and precipitate distribution characteristic of toughened, partially stabilized zirconia appear to be difficult to achieve in vapor deposited zirconia coatings

Applications of optical links to the protective instrumentation of nuclear power stations and to stabilisation of scintillation detectors

International Nuclear Information System (INIS)

Breuze, G.

1979-01-01

The description is given of a system of transmission by optical fibre opto-electronic links capable of carrying out many point by point transmissions of logical signals: between acquisition and protection processing units, between acquisition and protection processing units and the control room, between acquisition and protection processing units and logical safety units, and between logical safety units and control room. A short description is also given of an optical fibre signal transmission system constituting a new instrumentation for stabilising spectra coming from NaI (Tl) scintillation detectors. In addition to the remote control of the detectors such an instrumentation is capable of improving the stability performance of gamma ray cameras (a beam of monofibres is then necessary) as well as that of any detector placed in an inaccessible or hostile environment (fuel reprocessing plant, for example) [fr

Investigation of the oxygen exchange mechanism on Pt|yttria stabilized zirconia at intermediate temperatures: Surface path versus bulk path.

Science.gov (United States)

Opitz, Alexander K; Lutz, Alexander; Kubicek, Markus; Kubel, Frank; Hutter, Herbert; Fleig, Jürgen

2011-11-30

The oxygen exchange kinetics of platinum on yttria-stabilized zirconia (YSZ) was investigated by means of geometrically well-defined Pt microelectrodes. By variation of electrode size and temperature it was possible to separate two temperature regimes with different geometry dependencies of the polarization resistance. At higher temperatures (550-700 °C) an elementary step located close to the three phase boundary (TPB) with an activation energy of ∼1.6 eV was identified as rate limiting. At lower temperatures (300-400 °C) the rate limiting elementary step is related to the electrode area and exhibited a very low activation energy in the order of 0.2 eV. From these observations two parallel pathways for electrochemical oxygen exchange are concluded.The nature of these two elementary steps is discussed in terms of equivalent circuits. Two combinations of parallel rate limiting reaction steps are found to explain the observed geometry dependencies: (i) Diffusion through an impurity phase at the TPB in parallel to diffusion of oxygen through platinum - most likely along Pt grain boundaries - as area-related process. (ii) Co-limitation of oxygen diffusion along the Pt|YSZ interface and charge transfer at the interface with a short decay length of the corresponding transmission line (as TPB-related process) in parallel to oxygen diffusion through platinum.

Effect of microstructure and microhardness on the wear resistance of zirconia-alumina, zirconia-yttria and zirconia-ceria coatings manufactured by atmospheric plasma spraying; fecto de la microestructura y de la microdureza sobre la resistencia al desgaste de recubrimientos elaborados por proyeccion termica por plasma atmosferico a partir de circona-alumina, circona-itria y circona-ceria

Energy Technology Data Exchange (ETDEWEB)

Giovanni Gonzalez, A.; Ageorges, H.; Rojas, O.; Lopez, E.; Milena Hurtado, F.; Vargas, F.

2015-10-01

The effect of the structure and microhardness on the wear resistance of zirconia-alumina (ATZ), zirconia-yttria (YSZ) and zirconia-ceria (CSZ) coatings manufactured by atmospheric plasma spraying was studied. The microstructure and the fracture on the cross section of the coatings were analyzed using Scanning Electron Microscopy, the phases were identified using X-Ray Diffraction, the microhardness was measured by Vickers indentation and the wear resistance was evaluated by ball on disc test. The results showed that zirconia-alumina coating exhibits the best performance in the wear test. This behavior is closely related to their microstructure and higher microhardness, despite of its significant quantity of the monoclinic zirconia phase, which has lower mechanical properties than tetragonal zirconia phase. Tetragonal zirconia phase was predominant in the zirconia-yttria and zirconia-ceria coatings and despite this behavior; they did not have a good performance in the wear tests. This low wear resistance was mainly influenced by the columnar structure within their lamellae, which caused a greater detachment of particles in the contact surface during the ball-disc tests, increasing its wear. (Author)

Fracture toughness improvements of dental ceramic through use of yttria-stabilized zirconia (YSZ) thin-film coatings.

Science.gov (United States)

Chan, Ryan N; Stoner, Brian R; Thompson, Jeffrey Y; Scattergood, Ronald O; Piascik, Jeffrey R

2013-08-01

The aim of this study was to evaluate strengthening mechanisms of yttria-stabilized zirconia (YSZ) thin film coatings as a viable method for improving fracture toughness of all-ceramic dental restorations. Bars (2mm×2mm×15mm, n=12) were cut from porcelain (ProCAD, Ivoclar-Vivadent) blocks and wet-polished through 1200-grit using SiC abrasive. A Vickers indenter was used to induce flaws with controlled size and geometry. Depositions were performed via radio frequency magnetron sputtering (5mT, 25°C, 30:1 Ar/O2 gas ratio) with varying powers of substrate bias. Film and flaw properties were characterized by optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Flexural strength was determined by three-point bending. Fracture toughness values were calculated from flaw size and fracture strength. Data show improvements in fracture strength of up to 57% over unmodified specimens. XRD analysis shows that films deposited with higher substrate bias displayed a high %monoclinic volume fraction (19%) compared to non-biased deposited films (87%), and resulted in increased film stresses and modified YSZ microstructures. SEM analysis shows critical flaw sizes of 67±1μm leading to fracture toughness improvements of 55% over unmodified specimens. Data support surface modification of dental ceramics with YSZ thin film coatings to improve fracture toughness. Increase in construct strength was attributed to increase in compressive film stresses and modified YSZ thin film microstructures. It is believed that this surface modification may lead to significant improvements and overall reliability of all-ceramic dental restorations. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Decreased prevalence of hypercholesterolaemia and stabilisation of obesity trends in 5-year-old children: possible effects of changed public health policies.

Science.gov (United States)

Sedej, Katarina; Kotnik, Primož; Avbelj Stefanija, Magdalena; Grošelj, Urh; Širca Čampa, Andreja; Lusa, Lara; Battelino, Tadej; Bratina, Nataša

2014-02-01

Overweight/obesity in children is a worldwide public health problem. Together with hypercholesterolaemia they are associated with early atherosclerotic complications. In this study, we aimed to investigate the anthropometric characteristics and total cholesterol (TC) levels in a population of 5-year-old children, to determine trends in the prevalence of overweight/obesity and hypercholesterolaemia in 5-year-old children over a period of 8 years (2001-2009) and to assess the impact of modified national nutritional guidelines for kindergartens implemented in 2005. Cross-sectional studies of overweight/obesity prevalence in the years 2001, 2003-2005 and 2009, and hypercholesterolaemia in years 2001 and 2009, in 5-year-old children. Altogether, 12 832 (6308 girls/6524 boys) children were included. Overweight/obesity was defined by IOTF criteria. Hypercholesterolaemia was defined by TC level >5 mmol/l. Multivariable logistic regression models were used. NO CORRELATION BETWEEN BMI VALUES AND TC LEVELS WAS FOUND. OVERWEIGHT AND OBESITY PREVALENCE WERE STABILISED FROM 2001 TO 2009 (ODDS RATIO (OR) (95% CI): 1.13 (0.99-1.3) and 1.13 (0.89-1.42) respectively). Girls were more frequently overweight/obese than boys (OR (95% CI): 0.71 (0.65-0.79) and 0.75 (0.64-0.89) respectively). Prevalence of hypercholesterolaemia significantly decreased from 2001 to 2009 (OR (95% CI): 0.47 (0.41-0.55)). It was less frequent in boys than in girls (OR (95% CI): O.7 (0.61-0.8)). This is the first study to describe a negative trend in the prevalence of hypercholesterolaemia in pre-pubertal children. In addition, the prevalence of overweight/obesity in these children has been stabilised. Nationwide changes in public health policies could have influenced these observations.

Application of the electrophoretic deposition technique for obtaining Yttria-stabilized zirconia tubes; Aplicacao da tecnica de deposicao eletroforetica para a obtencao de tubos ceramicos de zirconia-itria

Energy Technology Data Exchange (ETDEWEB)

Caproni, E.; Muccillo, R., E-mail: ecaproni@gmail.com, E-mail: muccillo@usp.br [Centro de Ciencia e Tecnologia de Materiais, Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2012-01-15

The electrophoretic deposition (EPD) is recognized as the most versatile technique for processing particulate materials, due to low cost, deposition in minutes and forming of pieces with complex geometry shapes. In this work an experimental setup for the simultaneous conformation of 16 ceramic tubes by EPD was built. Bimodal submicron Yttria-stabilized zirconia particles were deposited into graphite electrodes, after suitably adjusting the rheological characteristics of the suspension in isopropanol. After graphite burning and YSZ sintering at 1500 deg C, the ceramic tubes were characterized by X-ray diffraction, scanning probe microscope, impedance spectroscopy and electrical response as a function of oxygen content. Small dense one end-closed ceramic tubes, fully stabilized in the cubic phase, were successfully obtained by the EPD technique, showing the ability of that technique for processing large quantities of tubular solid electrolytes with electrical response to different amounts of oxygen according to the Nernst law (author)

The inverse podant [Li3(NBut)3S)]+ stabilises a single ethylene oxide OCH=CH2 anion as a high- and low-temperature polymorph of [(thf)3Li3(OCH=CH2)(NBut)3S)].

Science.gov (United States)

Walfort, B; Pandey, S K; Stalke, D

2001-09-07

A single ethylene oxide anion derived from the ether cleavage reaction of thf with ButLi is stabilised by the inverse podant [Li3(NBut)3S)]+ to give a high- and a low-temperature polymorph with a considerable difference in conformation and packing.

Thermoanalytical study of the decomposition of yttrium trifluoroacetate thin films

International Nuclear Information System (INIS)

Eloussifi, H.; Farjas, J.; Roura, P.; Ricart, S.; Puig, T.; Obradors, X.; Dammak, M.

2013-01-01

We present the use of the thermal analysis techniques to study yttrium trifluoroacetate thin films decomposition. In situ analysis was done by means of thermogravimetry, differential thermal analysis, and evolved gas analysis. Solid residues at different stages and the final product have been characterized by X-ray diffraction and scanning electron microscopy. The thermal decomposition of yttrium trifluoroacetate thin films results in the formation of yttria and presents the same succession of intermediates than powder's decomposition, however, yttria and all intermediates but YF 3 appear at significantly lower temperatures. We also observe a dependence on the water partial pressure that was not observed in the decomposition of yttrium trifluoroacetate powders. Finally, a dependence on the substrate chemical composition is discerned. - Highlights: • Thermal decomposition of yttrium trifluoroacetate films. • Very different behavior of films with respect to powders. • Decomposition is enhanced in films. • Application of thermal analysis to chemical solution deposition synthesis of films

Phase evolution and thermal properties of yttria-stabilized hafnia nano-coatings deposited on alumina

Science.gov (United States)

Rubio, Ernesto Javier

High-temperature coatings are critical to the future power-generation systems and industries. Thermal barrier coatings (TBCs), which are usually the ceramic materials applied as thin coatings, protect engine components and allow further increase in engine temperatures for higher efficiency. Thus, the durability and reliability of the coating systems have to be more robust compared to current natural gas based engines. While a near and mid-term target is to develop TBC architecture with a 1300 °C surface temperature tolerance, a deeper understanding of the structure evolution and thermal behavior of the TBC-bond coat interface, specifically the thermally grown oxide (TGO), is of primary importance. In the present work, attention is directed towards yttria-stabilized hafnia (YSH) coatings on alumina (α-Al2O 3) to simulate the TBC-TGO interface and understand the phase evolution, microstructure and thermal oxidation of the coatings. YSH coatings were grown on α-Al2O3 substrates by sputter deposition by varying coating thickness in a wide range ˜30-1000 nm. The effect of coating thickness on the structure, morphology and the residual stress has been investigated using X-ray diffraction (XRD) and high resolution scanning electron microscopy (SEM). Thermal oxidation behavior of the coatings has been evaluated using the isothermal oxidation measurements under static conditions. X-ray diffraction analyses revealed the existence of monoclinic hafnia phase for relatively thin coatings indicating that the interfacial phenomena are dominant in phase stabilization. The evolution towards pure stabilized cubic phase of hafnia with the increasing coating thickness is observed. The SEM results indicate the changes in morphology of the coatings; the average grain size increases from 15 to 500 nm with increasing thickness. Residual stress was calculated employing XRD using the variable ψ-angle. Relation between residual stress and structural change is also studied. The results

Development and evaluation of suspension plasma sprayed yttria stabilized zirconia coatings as thermal barriers

Science.gov (United States)

van Every, Kent J.

The insulating effects from thermal barrier coatings (TBCs) in gas turbine engines allow for increased operational efficiencies and longer service lifetimes. Consequently, improving TBCs can lead to enhanced gas turbine engine performance. This study was conducted to investigate if yttria-stabilized zirconia (YSZ) coatings, the standard industrial choice for TBCs, produced from nano-sized powder could provide better thermal insulation than current commericial YSZ coatings generated using micron-sized powders. The coatings for this research were made via the recently developed suspension plasma spraying (SPS) process. With SPS, powders are suspended in a solvent containing dispersing agents; the suspension is then injected directly into a plasma flow that evaporates the solvent and melts the powder while transporting it to the substrate. Although related to the industrial TBC production method of air plasma spraying (APS), SPS has two important differences---the ability to spray sub-micron diameter ceramic particles, and the ability to alloy the particles with chemicals dissolved in the solvent. These aspects of SPS were employed to generate a series of coatings from suspensions containing ˜100 nm diameter YSZ powder particles, some of which were alloyed with neodymium and ytterbium ions from the solvent. The SPS coatings contained columnar structures not observed in APS TBCs; thus, a theory was developed to explain the formation of these features. The thermal conductivity of the coatings was tested to evaluate the effects of these unique microstructures and the effects of the alloying process. The results for samples in the as-sprayed and heat-treated conditions were compared to conventional YSZ TBCs. This comparison showed that, relative to APS YSZ coatings, the unalloyed SPS samples typically exhibited higher as-sprayed and lower heat-treated thermal conductivities. All thermal conductivity values for the alloyed samples were lower than conventional YSZ TBCs

Type-Directed Partial Evaluation

DEFF Research Database (Denmark)

Danvy, Olivier

1998-01-01

Type-directed partial evaluation uses a normalization function to achieve partial evaluation. These lecture notes review its background, foundations, practice, and applications. Of specific interest is the modular technique of offline and online type-directed partial evaluation in Standard ML...

Type-Directed Partial Evaluation

DEFF Research Database (Denmark)

Danvy, Olivier

1998-01-01

Type-directed partial evaluation uses a normalization function to achieve partial evaluation. These lecture notes review its background, foundations, practice, and applications. Of specific interest is the modular technique of offline and online type-directed partial evaluation in Standard ML of ...

Evaluation du risque de déstabilisation des infrastructures de haute montagne engendré par le réchauffement climatique dans les Alpes françaises

OpenAIRE

Duvillard, Pierre-Allain; Ravanel, Ludovic; Deline, Philip

2015-01-01

Dans le contexte du changement climatique actuel, les milieux de haute montagne sont soumis à de profonds bouleversements tels que la fonte des glaciers ou la dégradation du permafrost, à l’origine de mouvements de versant au sein des parois rocheuses comme des formations superficielles. Ces processus impliquent des risques directs de déstabilisation pour les infrastructures (refuges, remontées mécaniques, etc.). Dans un but de prévention de ces risques, un recensement des infrastructures de ...

Application of sol gel spin coated yttria-stabilized zirconia layers for the improvement of solid oxide fuel cell electrolytes produced by atmospheric plasma spraying

Energy Technology Data Exchange (ETDEWEB)

Rose, Lars [University of British Columbia, Department of Materials Engineering, 309-6350 Stores Road, Vancouver, British Columbia, V6T 1Z4 (Canada); National Research Council, Institute for Fuel Cell Innovation, 4250 Wesbrook Mall, Vancouver, British Columbia, V6T 1W5 (Canada); Kesler, Olivera [National Research Council, Institute for Fuel Cell Innovation, 4250 Wesbrook Mall, Vancouver, British Columbia, V6T 1W5 (Canada); University of British Columbia, Department of Mechanical Engineering, 2054-6250 Applied Science Lane, Vancouver, British Columbia, V6T 1Z4 (Canada); Tang, Zhaolin; Burgess, Alan [Northwest Mettech Corp., 467 Mountain Hwy, North Vancouver, British Columbia, V7J 2L3 (Canada)

2007-05-15

Due to its high thermal stability and purely oxide ionic conductivity, yttria-stabilized zirconia (YSZ) is the most commonly used electrolyte material for solid oxide fuel cells (SOFCs). Standard electrolyte fabrication techniques for planar SOFCs involve wet ceramic techniques such as tape-casting or screen printing, requiring sintering steps at temperatures above 1300 C. Plasma spraying (PS) may provide a more rapid and cost efficient method to produce SOFCs without sintering. High-temperature sintering requires long processing times and can lead to oxidation of metal alloys used as mechanical supports, or to detrimental interreactions between the electrolyte and adjacent electrode layers. This study investigates the use of spin coated sol gel derived YSZ precursor solutions to fill the pores present in plasma sprayed YSZ layers, and to enhance the surface area for reaction at the electrolyte-cathode interface, without the use of high-temperature firing steps. The effects of different plasma conditions and sol concentrations and solid loadings on the gas permeability and fuel cell performance have been investigated. (author)

Compatriot partiality and cosmopolitan justice: Can we justify compatriot partiality within the cosmopolitan framework?

Directory of Open Access Journals (Sweden)

Rachelle Bascara

2016-10-01

Full Text Available This paper shows an alternative way in which compatriot partiality could be justified within the framework of global distributive justice. Philosophers who argue that compatriot partiality is similar to racial partiality capture something correct about compatriot partiality. However, the analogy should not lead us to comprehensively reject compatriot partiality. We can justify compatriot partiality on the same grounds that liberation movements and affirmative action have been justified. Hence, given cosmopolitan demands of justice, special consideration for the economic well-being of your nation as a whole is justified if and only if the country it identifies is an oppressed developing nation in an unjust global order.This justification is incomplete. We also need to say why Person A, qua national of Country A, is justified in helping her compatriots in Country A over similarly or slightly more oppressed non-compatriots in Country B. I argue that Person A’s partiality towards her compatriots admits further vindication because it is part of an oppressed group’s project of self-emancipation, which is preferable to paternalistic emancipation.Finally, I identify three benefits in my justification for compatriot partiality. First, I do not offer a blanket justification for all forms of compatriot partiality. Partiality between members of oppressed groups is only a temporary effective measure designed to level an unlevel playing field. Second, because history attests that sovereign republics could arise as a collective response to colonial oppression, justifying compatriot partiality on the grounds that I have identified is conducive to the development of sovereignty and even democracy in poor countries, thereby avoiding problems of infringement that many humanitarian poverty alleviation efforts encounter. Finally, my justification for compatriot partiality complies with the implicit cosmopolitan commitment to the realizability of global justice

Crystallization kinetics and growth mechanism of 8 mol% yttria-stabilized zirconia (8YSZ) nano-powders prepared by a sol-gel process

Energy Technology Data Exchange (ETDEWEB)

Kuo, C.-W. [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Lee, Y.-H. [Department of Materials Science and Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Hung, I-M. [Department of Chemical Engineering and Materials Science, Yuan Ze University, 135 Far-East Road, Chung-Li, Taoyuan, Taiwan (China); Wang, M.-C. [Faculty of Fragrance and Cosmetics, Kaohsiung Medical University, 100 Shi-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Wen, S.-B. [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Fung, K.-Z. [Department of Materials Science and Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Shih, C.-J. [Faculty of Fragrance and Cosmetics, Kaohsiung Medical University, 100 Shi-Chuan 1st Road, Kaohsiung 807, Taiwan (China)], E-mail: cjshih@kmu.edu.tw

2008-04-03

Eight mol% yttria-stabilized zirconia (8YSZ) gel powders were synthesized at 348 K for 2 h using ZrOCl{sub 2}.8H{sub 2}O and Y(NO{sub 3}){sub 3}.6H{sub 2}O as starting materials in an ethanol-water solution by a sol-gel process. The crystallization kinetics and growth mechanism of the 8YSZ gel powders have been investigated using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and selected area electron diffraction (SAED). The XRD results and SAED pattern show that the 8YSZ gel powders calcined at 773 K for 2 h is a cubic ZrO{sub 2}. The activation energy for the crystallization of the cubic ZrO{sub 2} formation in the 8YSZ gel powders is determined as 231.76 kJ/mol by a non-isothermal DTA method. Both growth morphology parameter (n) and crystallization mechanism index (m) are close to 3.0, indicating that the bulk nucleation is dominant in the cubic ZrO{sub 2} formation. The TEM examination shows that the cubic ZrO{sub 2} has a spherical-like morphology with a size ranging from 10 to 20 nm.

Essays on partial retirement

NARCIS (Netherlands)

Kantarci, T.

2012-01-01

The five essays in this dissertation address a range of topics in the micro-economic literature on partial retirement. The focus is on the labor market behavior of older age groups. The essays examine the economic and non-economic determinants of partial retirement behavior, the effect of partial

YSZ thin films deposited on NiO-CSZ anodes by pulsed injection MOCVD for intermediate temperature-SOFC applications

International Nuclear Information System (INIS)

Garcia, G.; Pardo, J.A.; Santiso, J.; Merino, R.I.; Orera, V.M.; Larrea, A.; Pena, J.I.; Laguna-Bercero, M.A.; Figueras, A.

2004-01-01

Yttria-stabilized zirconia (YSZ) films are prepared on NiO-CaSZ by PIMOCVD (pulsed injection metal organic chemical vapor deposition). High quality, 5 to 10 μm thick, totally dense YSZ layers are prepared by controlling the oxygen partial pressure during the deposition. YSZ solid electrolyte deposition onto Ni-YSZ eutectic substrate is found to be a promising combination with regard to intermediate-temperature solid-oxide fuel cell applications. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

In situ probing of temperature in radio frequency thermal plasma using Yttrium ion emission lines during synthesis of yttria nanoparticles

Science.gov (United States)

Dhamale, G. D.; Tiwari, N.; Mathe, V. L.; Bhoraskar, S. V.; Ghorui, S.

2017-07-01

Particle feeding is used in the most important applications of radio frequency (r.f.) thermal plasmas like synthesis of nanoparticles and particle spheroidization. The study reports an in-situ investigation of radial distribution of temperature in such devices using yttrium ion emission lines under different rates of particle loading during synthesis of yttria nanoparticles. A number of interesting facts about the response of r.f. plasma to the rate of particle loading, hitherto unknown, are revealed. Observed phenomena are supported with experimental data from fast photographic experiments and actual synthesis results. The use of the Abel inversion technique together with simultaneous multi-track acquisition of emission spectra from different spatial locations using a CCD based spectrometer allowed us to extract accurate distribution of temperature inside the plasma in the presence of inherent instabilities. The temperature profiles of this type of plasma have been measured possibly for the first time while particles are being fed into the plasma. Observed changes in the temperature profiles as the particle feed rate increases are very significant. Reaction forces resulting from particle evaporation, and increased skin depth owing to the decrease in electrical conductivity in the edge region are proposed as the two different mechanisms to account for the observed changes in the temperature profile as the powder feed rate is increased. Quantitative analyses supporting the proposed mechanisms are presented.

Process envelopes for stabilisation/solidification of contaminated soil using lime-slag blend.

Science.gov (United States)

Kogbara, Reginald B; Yi, Yaolin; Al-Tabbaa, Abir

2011-09-01

Stabilisation/solidification (S/S) has emerged as an efficient and cost-effective technology for the treatment of contaminated soils. However, the performance of S/S-treated soils is governed by several intercorrelated variables, which complicates the optimisation of the treatment process design. Therefore, it is desirable to develop process envelopes, which define the range of operating variables that result in acceptable performance. In this work, process envelopes were developed for S/S treatment of contaminated soil with a blend of hydrated lime (hlime) and ground granulated blast furnace slag (GGBS) as the binder (hlime/GGBS = 1:4). A sand contaminated with a mixture of heavy metals and petroleum hydrocarbons was treated with 5%, 10% and 20% binder dosages, at different water contents. The effectiveness of the treatment was assessed using unconfined compressive strength (UCS), permeability, acid neutralisation capacity and contaminant leachability with pH, at set periods. The UCS values obtained after 28 days of treatment were up to ∼800 kPa, which is quite low, and permeability was ∼10(-8) m/s, which is higher than might be required. However, these values might be acceptable in some scenarios. The binder significantly reduced the leachability of cadmium and nickel. With the 20% dosage, both metals met the waste acceptance criteria for inert waste landfill and relevant environmental quality standards. The results show that greater than 20% dosage would be required to achieve a balance of acceptable mechanical and leaching properties. Overall, the process envelopes for different performance criteria depend on the end-use of the treated material.

Structure and chemistry of epitaxial ceria thin films on yttria-stabilized zirconia substrates, studied by high resolution electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Sinclair, Robert, E-mail: bobsinc@stanford.edu [Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305 (United States); Lee, Sang Chul, E-mail: sclee99@stanford.edu [Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305 (United States); Shi, Yezhou; Chueh, William C. [Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305 (United States); Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, CA 94025 (United States); Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, Menlo Park, CA 94025 (United States)

2017-05-15

We have applied aberration-corrected transmission electron microscopy (TEM) imaging and electron energy loss spectroscopy (EELS) to study the structure and chemistry of epitaxial ceria thin films, grown by pulsed laser deposition onto (001) yttria-stabilized zirconia (YSZ) substrates. There are few observable defects apart from the expected mismatch interfacial dislocations and so the films would be expected to have good potential for applications. Under high electron beam dose rate (above about 6000 e{sup -}/Å{sup 2}s) domains of an ordered structure appear and these are interpreted as being created by oxygen vacancy ordering. The ordered structure does not appear at lower lose rates (ca. 2600 e{sup -}/Å{sup 2}s) and can be removed by imaging under 1 mbar oxygen gas in an environmental TEM. EELS confirms that there is both oxygen deficiency and the associated increase in Ce{sup 3+} versus Ce{sup 4+} cations in the ordered domains. In situ high resolution TEM recordings show the formation of the ordered domains as well as atomic migration along the ceria thin film (001) surface. - Highlights: • The local structure and chemistry of ceria can be studied by TEM combined with EELS. • At lower electron, there are no observable changes in the ceria thin films. • At higher dose rates, an ordered phase is created due to oxygen vacancy ordering. • In situ HRTEM shows the oxygen vacancy ordering and the movement of surface atoms.

Behaviour of rock-like oxide fuels under reactivity-initiated accident conditions

International Nuclear Information System (INIS)

Kazuyuki, Kusagaya; Takehiko, Nakamura; Makio, Yoshinaga; Hiroshi, Akie; Toshiyuki, Yamashita; Hiroshi, Uetsuka

2002-01-01

Pulse irradiation tests of three types of un-irradiated rock-like oxide (ROX) fuel - yttria-stabilised zirconia (YSZ) single phase, YSZ and spinel (MgAl 2 O 4 ) homogeneous mixture and particle-dispersed YSZ/spinel - were conducted in the Nuclear Safety Research Reactor to investigate the fuel behaviour under reactivity-initiated accident conditions. The ROX fuels failed at fuel volumetric enthalpies above 10 GJ/m 3 , which was comparable to that of un-irradiated UO 2 fuel. The failure mode of the ROX fuels, however, was quite different from that of the UO 2 fuel. The ROX fuels failed with fuel pellet melting and a part of the molten fuel was released out to the surrounding coolant water. In spite of the release, no significant mechanical energy generation due to fuel/coolant thermal interaction was observed in the tested enthalpy range below∼12 GJ/m 3 . The YSZ type and homogenous YSZ/spinel type ROX fuels failed by cladding burst when their temperatures peaked, while the particle-dispersed YSZ/spinel type ROX fuel seemed to have failed by cladding local melting. (author)

The study of flow and proton exchange interactions in the cylindrical solid oxide fuel cell

CERN Document Server

Saievar-Iranizad, E

2002-01-01

The solid oxide fuel cell operates at high temperature of about 1000 deg C. In this temperature, some known materials such as Ni, ... which is abundant in the nature, can be used as a catalyst in the electrodes. The electrolytes of such cell solid oxide fuel cell can be made through non-porous solid ceramics such as Zircon's (ZrO sub 2). It can be stabilized using a doped Yttrium oxide. The importance of Yttria-stabilised Zirconia at high temperature belongs to the transport of oxygen ions through the electrolyte. Oxygen using in the hot cathode side causes a considerable reduction in the concentration of oxygen molecules. The oxygen ions exchange through the electrolyte relates to the molecular oxygen concentration gradient between the anode and cathode. Applying fuels such as hydrogen or natural gas in the anode and its chemical reaction with oxygen ions transfer from cathode through the electrolyte, produce electricity, water and heat. To study the ion exchange and its interaction into solid oxide fuel cel...

Determination of Scattering and Absorption Coefficients for Plasma-Sprayed Yttria-Stabilized Zirconia Thermal Barrier Coatings at Elevated Temperatures

Science.gov (United States)

Eldridge, Jeffrey I.; Spuckler, Charles M.; Markham, James R.

2009-01-01

The temperature dependence of the scattering and absorption coefficients for a set of freestanding plasma-sprayed 8 wt% yttria-stabilized zirconia (8YSZ) thermal barrier coatings (TBCs) was determined at temperatures up to 1360 C in a wavelength range from 1.2 micrometers up to the 8YSZ absorption edge. The scattering and absorption coefficients were determined by fitting the directional-hemispherical reflectance and transmittance values calculated by a four-flux Kubelka Munk method to the experimentally measured hemispherical-directional reflectance and transmittance values obtained for five 8YSZ thicknesses. The scattering coefficient exhibited a continuous decrease with increasing wavelength and showed no significant temperature dependence. The scattering is primarily attributed to the relatively temperature-insensitive refractive index mismatch between the 8YSZ and its internal voids. The absorption coefficient was very low (less than 1 per centimeter) at wavelengths between 2 micrometers and the absorption edge and showed a definite temperature dependence that consisted of a shift of the absorption edge to shorter wavelengths and an increase in the weak absorption below the absorption edge with increasing temperature. The shift in the absorption edge with temperature is attributed to strongly temperature-dependent multiphonon absorption. While TBC hemispherical transmittance beyond the absorption edge can be predicted by a simple exponential decrease with thickness, below the absorption edge, typical TBC thicknesses are well below the thickness range where a simple exponential decrease in hemispherical transmittance with TBC thickness is expected. [Correction added after online publication August 11, 2009: "edge to a shorter wavelengths" has been updated as edge to shorter wavelengths."

Anatomic partial nephrectomy: technique evolution.

Science.gov (United States)

Azhar, Raed A; Metcalfe, Charles; Gill, Inderbir S

2015-03-01

Partial nephrectomy provides equivalent long-term oncologic and superior functional outcomes as radical nephrectomy for T1a renal masses. Herein, we review the various vascular clamping techniques employed during minimally invasive partial nephrectomy, describe the evolution of our partial nephrectomy technique and provide an update on contemporary thinking about the impact of ischemia on renal function. Recently, partial nephrectomy surgical technique has shifted away from main artery clamping and towards minimizing/eliminating global renal ischemia during partial nephrectomy. Supported by high-fidelity three-dimensional imaging, novel anatomic-based partial nephrectomy techniques have recently been developed, wherein partial nephrectomy can now be performed with segmental, minimal or zero global ischemia to the renal remnant. Sequential innovations have included early unclamping, segmental clamping, super-selective clamping and now culminating in anatomic zero-ischemia surgery. By eliminating 'under-the-gun' time pressure of ischemia for the surgeon, these techniques allow an unhurried, tightly contoured tumour excision with point-specific sutured haemostasis. Recent data indicate that zero-ischemia partial nephrectomy may provide better functional outcomes by minimizing/eliminating global ischemia and preserving greater vascularized kidney volume. Contemporary partial nephrectomy includes a spectrum of surgical techniques ranging from conventional-clamped to novel zero-ischemia approaches. Technique selection should be tailored to each individual case on the basis of tumour characteristics, surgical feasibility, surgeon experience, patient demographics and baseline renal function.

Spekkens’ toy model in all dimensions and its relationship with stabiliser quantum mechanics

Science.gov (United States)

Catani, Lorenzo; E Browne, Dan

2017-07-01

Spekkens’ toy model is a non-contextual hidden variable model with an epistemic restriction, a constraint on what an observer can know about reality. The aim of the model, developed for continuous and discrete prime degrees of freedom, is to advocate the epistemic view of quantum theory, where quantum states are states of incomplete knowledge about a deeper underlying reality. Many aspects of quantum mechanics and protocols from quantum information can be reproduced in the model. In spite of its significance, a number of aspects of Spekkens’ model remained incomplete. Formal rules for the update of states after measurement had not been written down, and the theory had only been constructed for prime-dimensional and infinite dimensional systems. In this work, we remedy this, by deriving measurement update rules and extending the framework to derive models in all dimensions, both prime and non-prime. Stabiliser quantum mechanics (SQM) is a sub-theory of quantum mechanics with restricted states, transformations and measurements. First derived for the purpose of constructing error correcting codes, it now plays a role in many areas of quantum information theory. Previously, it had been shown that Spekkens’ model was operationally equivalent to SQM in the case of odd prime dimensions. Here, exploiting known results on Wigner functions, we extend this to show that Spekkens’ model is equivalent to SQM in all odd dimensions, prime and non-prime. This equivalence provides new technical tools for the study of technically difficult compound-dimensional SQM.

Spekkens’ toy model in all dimensions and its relationship with stabiliser quantum mechanics

International Nuclear Information System (INIS)

Catani, Lorenzo; Browne, Dan E

2017-01-01

Spekkens’ toy model is a non-contextual hidden variable model with an epistemic restriction, a constraint on what an observer can know about reality. The aim of the model, developed for continuous and discrete prime degrees of freedom, is to advocate the epistemic view of quantum theory, where quantum states are states of incomplete knowledge about a deeper underlying reality. Many aspects of quantum mechanics and protocols from quantum information can be reproduced in the model. In spite of its significance, a number of aspects of Spekkens’ model remained incomplete. Formal rules for the update of states after measurement had not been written down, and the theory had only been constructed for prime-dimensional and infinite dimensional systems. In this work, we remedy this, by deriving measurement update rules and extending the framework to derive models in all dimensions, both prime and non-prime. Stabiliser quantum mechanics (SQM) is a sub-theory of quantum mechanics with restricted states, transformations and measurements. First derived for the purpose of constructing error correcting codes, it now plays a role in many areas of quantum information theory. Previously, it had been shown that Spekkens’ model was operationally equivalent to SQM in the case of odd prime dimensions. Here, exploiting known results on Wigner functions, we extend this to show that Spekkens’ model is equivalent to SQM in all odd dimensions, prime and non-prime. This equivalence provides new technical tools for the study of technically difficult compound-dimensional SQM. (paper)

Management of sleep-time masticatory muscle activity using stabilisation splints affects psychological stress.

Science.gov (United States)

Takahashi, H; Masaki, C; Makino, M; Yoshida, M; Mukaibo, T; Kondo, Y; Nakamoto, T; Hosokawa, R

2013-12-01

To treat sleep bruxism (SB), symptomatic therapy using stabilisation splints (SS) is frequently used. However, their effects on psychological stress and sleep quality have not yet been examined fully. The objective of this study was to clarify the effects of SS use on psychological stress and sleep quality. The subjects (11 men, 12 women) were healthy volunteers. A crossover design was used. Sleep measurements were performed for three consecutive days or longer without (baseline) or with an SS or palatal splint (PS), and data for the final day were evaluated. We measured masseter muscle activity during sleep using portable electromyography to evaluate SB. Furthermore, to compare psychological stress before and after sleep, assessments were made based on STAI-JYZ and the measurement of salivary chromogranin A. To compare each parameter among the three groups (baseline, SS and PS), Friedman's and Dunn's tests were used. From the results of the baseline measurements, eight subjects were identified as high group and 15 as low group. Among the high group, a marked decrease in the number of bruxism events per hour and an increase in the difference in the total STAI Y-1 scores were observed in the SS group compared with those at baseline (P sleep stages. SS use may be effective in reducing the number of SB events, while it may increase psychological stress levels, and SS use did not apparently influence sleep stages. © 2013 John Wiley & Sons Ltd.

Tutorial on Online Partial Evaluation

Directory of Open Access Journals (Sweden)

William R. Cook

2011-09-01

Full Text Available This paper is a short tutorial introduction to online partial evaluation. We show how to write a simple online partial evaluator for a simple, pure, first-order, functional programming language. In particular, we show that the partial evaluator can be derived as a variation on a compositionally defined interpreter. We demonstrate the use of the resulting partial evaluator for program optimization in the context of model-driven development.

Characterization of the yttria-stabilized zirconia thin film electrophoretic deposited on La{sub 0.8}Sr{sub 0.2}MnO{sub 3} substrate

Energy Technology Data Exchange (ETDEWEB)

Yang, Koho [Department of Mold and Die Engineering, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Rode, Kaohsiung 80782, Taiwan (China); Shen, Jung-Hsiung [Department of Mold and Die Engineering, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Rode, Kaohsiung 80782, Taiwan (China); Yang, Kai-Yun [Department of Materials Science and Engineering, National Chen Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Hung, I-Ming [Department of Materials Science and Engineering, National Chen Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Department of Chemical Engineering and Materials Science, Yuan Ze University, 135 Yuan-Tung Road, Chungli, Taoyunn 320, Taiwan (China); Fung, Kuan-Zong [Department of Materials Science and Engineering, National Chen Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Wang, Moo-Chin [Faculty of Fragrance and Cosmetics, Kaohsiung Medical University, 100 Shi-Chuan 1st Road, Kaohsiung 807, Taiwan (China)]. E-mail: mcwang@kmu.edu.tw

2007-06-14

The yttria-stabilized zirconia (YSZ) thin films electrophoretic deposited on the La{sub 0.8}Sr{sub 0.2}MnO{sub 3} (LSM) substrate have been characterized by using zeta potential analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The La{sub 2}Zr{sub 2}O{sub 7} (LZ) formed at the interface between the YSZ thin film and LSM substrate, after sintered at 1400 {sup o}C for 52 h, are identified by XRD. The zeta potential of the YSZ particles in pure ethanol-acetone is about 7.8 mV, but when the I{sub 2} concentration is greater than 0.6 g/1, the zeta potential attains a constant value, 46 mV. The relation between deposit weight of the YSZ films and the applied voltage shows a non-linear behavior. Thickness of the YSZ thin film deposited on the LSM substrate by electrophoretic deposition is controlled by a diffusion process. A larger LZ with the thickness of 200 nm is formed at the interface between the YSZ film and the LSM substrate.

Partially Observed Mixtures of IRT Models: An Extension of the Generalized Partial-Credit Model

Science.gov (United States)

Von Davier, Matthias; Yamamoto, Kentaro

2004-01-01

The generalized partial-credit model (GPCM) is used frequently in educational testing and in large-scale assessments for analyzing polytomous data. Special cases of the generalized partial-credit model are the partial-credit model--or Rasch model for ordinal data--and the two parameter logistic (2PL) model. This article extends the GPCM to the…