Application of the LBB concept to nuclear power plants with WWER 440 and WWER 1000 reactors

International Nuclear Information System (INIS)

Zdarek, J.; Pecinka, L.

1997-01-01

Leak-before-break (LBB) analysis of WWER type reactors in the Czech and Sloval Republics is summarized in this paper. Legislative bases, required procedures, and validation and verification of procedures are discussed. A list of significant issues identified during the application of LBB analysis is presented. The results of statistical evaluation of crack length characteristics are presented and compared for the WWER 440 Type 230 and 213 reactors and for the WWER 1000 Type 302, 320 and 338 reactors

Experimental verification of lifetime of bolting joints for WWER reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Polachova, H.

1992-01-01

This paper presents results from experimental verification of cyclic lifetime of bolting joints of M 140x6 mm type used for WWER-440 MW reactor pressure vessels. Bolting joints or real dimensions were tested in a special testing equipment ZS 1000 in Skoda Concern. Stud bolts are made from 25Kh1MF or 38KhN3MFA type of steels. Tests were carried out at operating as well as at room temperatures with coefficient of asymmetry equal to 0.1; one tests was realized with given bending moment. Experimental results have been compared with calculated lifetimes according to ASME, Soviet and CMEA Codes. In all cases calculations give conservative assessments. (orig.)

Activities in the Czech Republic for reactor pressure components lifetime management

International Nuclear Information System (INIS)

Brumovsky, M.

1994-01-01

The following activities in the Czech republic for reactor pressure components lifetime management are described: upgrading and safety assurance of nuclear power plants (NPP) with reactors of WWER-440/V-230 type, safety assurance of NPPs with reactors of WWER-440/V-213, lifetime management programme of NPPs with WWER-440/V-213 reactors, preparation of start-up of NPPs with WWER-1000/V-320 reactors, preparation of guides for lifetime as well as defect allowability evaluation in main components of primary and secondary circuits. 3 figs

WWER reactor fuel performance, modelling and experimental support. Proceedings

International Nuclear Information System (INIS)

Stefanova, S.; Chantoin, P.; Kolev, I.

1994-01-01

This publication is a compilation of 36 papers presented at the International Seminar on WWER Reactor Fuel Performance, Modelling and Experimental Support, organised by the Institute for Nuclear Research and Nuclear Energy (BG), in cooperation with the International Atomic Energy Agency. The Seminar was attended by 76 participants from 16 countries, including representatives of all major Russian plants and institutions responsible for WWER reactor fuel manufacturing, design and research. The reports are grouped in four chapters: 1) WWER Fuel Performance and Economics: Status and Improvement Prospects: 2) WWER Fuel Behaviour Modelling and Experimental Support; 3) Licensing of WWER Fuel and Fuel Analysis Codes; 4) Spent Fuel of WWER Plants. The reports from the corresponding four panel discussion sessions are also included. All individual papers are recorded in INIS as separate items

WWER reactor fuel performance, modelling and experimental support. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Stefanova, S; Chantoin, P; Kolev, I [eds.

1994-12-31

This publication is a compilation of 36 papers presented at the International Seminar on WWER Reactor Fuel Performance, Modelling and Experimental Support, organised by the Institute for Nuclear Research and Nuclear Energy (BG), in cooperation with the International Atomic Energy Agency. The Seminar was attended by 76 participants from 16 countries, including representatives of all major Russian plants and institutions responsible for WWER reactor fuel manufacturing, design and research. The reports are grouped in four chapters: (1) WWER Fuel Performance and Economics: Status and Improvement Prospects: (2) WWER Fuel Behaviour Modelling and Experimental Support; (3) Licensing of WWER Fuel and Fuel Analysis Codes; (4) Spent Fuel of WWER Plants. The reports from the corresponding four panel discussion sessions are also included. All individual papers are recorded in INIS as separate items.

WWER-1000 reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series 12, 'Reactor Simulator Development' (2001). Course material for workshops using a pressurized water reactor (PWR) Simulator developed for the IAEA by Cassiopeia Technologies Inc. of Canada is presented in the IAEA publication: Training Course Series No. 22 'Pressurized Water Reactor Simulator' (2003) and Training Course Series No. 23 'Boiling Water Reactor Simulator' (2003). This report consists of course material for workshops using the WWER-1000 Reactor Department Simulator from the Moscow Engineering and Physics Institute, Russian Federation. N. V. Tikhonov and S. B. Vygovsky of the Moscow Engineering and Physics Institute prepared this report for the IAEA

International workshop on WWER-440 reactor pressure vessel embrittlement and annealing. Working material

International Nuclear Information System (INIS)

1994-01-01

The purpose of the Workshop was essentially to discuss the WWER 440 model 230 reactor pressure vessel integrity in terms of the measures already taken, current activities and future plans. The meeting was arranged in two parts, namely, the Scientific programme followed by the consideration, review and revision of the IAEA Consultancy report on RPV Embrittlement and Annealing. This particular report covers the first part of the meeting i.e., the Scientific Programme, in the form of proceedings of the meeting, while the re-drafted Consultancy report will be issued later. The meeting was attended by sixty-six representatives from thirteen countries. Refs, figs and tabs

Anticipated transients without scram for WWER reactors. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1999-12-01

Anticipated transients without scram (ATWS) are anticipated operational occurrences followed by the failure of one reactor scram function. Current international practice requires that the capability of pressurized water reactors (PWRs) to cope with ATWS be demonstrated following a systematic evaluation of plants' defence in depth. Countries operating PWRs require design consideration of ATWS events on a deterministic basis. The regulatory requirements may concern either specific mitigating systems or acceptable plant performance during these events. The prevailing international practice for performing transient analysis of ATWS for licensing is the best estimate approach. Available transient analyses of ATWS events indicate that WWER reactors, like PWRs, have the tendency to shut themselves down if the inherent nuclear feedback is sufficiently negative. Various control and limitation functions of the WWER plants also provide a degree of defence against ATWS. However, for most WWER plants, complete and systematic ATWS analyses have yet to be submitted for rigorous review by the regulatory authorities and preventive or mitigative measures have not been established. In addition, it has also been recognized that plant behaviour in case of ATWS also relies on certain system functions (use of pressurizer safety valves for liquid discharge, availability of steam dump valve to both the condenser (BRU-K) and the atmosphere (BRU-A) for secondary side pressure control, and others) which have been identified as safety issues and need to be qualified for accident conditions. In all countries operating WWERs, the need for ATWS investigations is recognized and reflected in the safety improvement programmes. ATWS analysis for WWERs is not required for the licensing process in Bulgaria, the Czech Republic (with the exception of the Temelin nuclear power plant) and Russia. Design consideration of ATWS is required if expert assessments of probabilistic safety assessment (PSA) results

Methodology for the evaluation of tolerability of defects in WWER-1000/V-320 reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Horacek, L.; Ruscak, M.

1996-05-01

The methodology provides guidelines for the assessment of tolerability of defects found during in-service inspection of the base material and overlay of WWER-1000/V-320 type reactor pressure vessels. With regard to the method of calculating the tolerability of defects and rules for the preparation and implementation of repairs, this methodology can also find use in the assessment of tolerability of defects in selected facilities of WWER-1000/V-320 type nuclear power plants provided that adequate input data concerning the materials, manufacturing technology, and operating load regime are available and that the facilities are made of ferrite/bainite type steels. This methodology should serve as a binding document underlying the development of a technical approach to provisions for a further operation of facilities in which intolerable defects have been found by nondestructive testing. (author)

Calculation models of pressure wave propagation within the WWER-440 primary circulating loop

International Nuclear Information System (INIS)

Adamik, V.; Tkach, A.

1982-01-01

Computer codes SHOCK, LOVE, BAREL are described that can be used for the study of pressure wave propagation within the reactor and pipeline system during a LOCA as well as for mechanical loads identification in various parts of the system. SHOCK code is applicable to one-dimensional pressure wave propagation analysis in any hydraulic network containing a compressible nonviscous liquid with a constant (within the considered transient process period) density. LOVE code allows to calculate non-symmetrical mechanical loads on the WWER shaft in case of the main circulation pipeline cold branch rupture. BAREL code is an advanced modification of SHOCK code. It is fitted for two-dimensional pressure wave propagation analysing in the downstream section of a pressurised water reactor in case of the main circulation pipeline cold branch rupture. The calculation results for B-213 type WWER-440 reactor are presented that have been obtained under the assumption of perfect structure rigidity [ru

Post mortem investigations of the NPP Greifswald WWER-440 reactor pressure vessels

International Nuclear Information System (INIS)

Schuhknecht, Jan; Viehrig, Hans-Werner; Weiss, Frank-Peter; Rindelhardt, Udo

2008-01-01

The paper presents first results of the post mortem investigations performed at the reactor pressure vessels (RPV) of the Russian WWER-440 type reactors. Trepans were taken from the core weld SN0.1.4 and base metal of the unit 1 RPV. This RPV was annealed after 15 years of operation and operated for two more years. At first the trepan of the core welding seam was investigated by Master Curve (MC) testing. Specimens from 5 locations through the thickness of the welding seam were tested according to ASTM E1921-05. The reference temperature T 0 was calculated with the measured fracture toughness values, K Jc , at brittle failure of the specimen. Generally the K Jc values measured on pre-cracked and side-grooved Charpy size SE(B) specimens of the investigated weld metal follow the course of the Master Curve. The K Jc values show a remarkable scatter. More values than expected lie below the 5% fractile. In addition the MC SINTAP procedure was applied to determine T 0 SINTAP of the brittle fraction of the data set. There are remarkable differences between T 0 and T 0 SINTAP indicating macroscopic inhomogeneous weld metal. The highest T 0 was about 50 C at a distance of 22 mm from the inner surface of the weld. It is 40 K higher compared with T 0 at the inner surface. This is important for the assessment of ductile-to-brittle temperatures measured with sub size Charpy specimens made of weld metal from the inner RPV wall. This material may not represent the most conservative condition. The results presented in this paper show that the Master Curve approach as adopted in the test standard ASTM E1921-05 is applicable to the investigated WWER-440 multilayer weld metal. The results are of direct importance for an advanced WWER-440 RPV integrity assessment. On the other hand the data pool is broadened for a general introduction of the MC based RPV integrity assessment in the national codes. Furthermore general experiences in the cutting of irradiated RPV steels are collected

Post mortem investigations of the NPP Greifswald WWER-440 reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Schuhknecht, Jan; Viehrig, Hans-Werner; Weiss, Frank-Peter; Rindelhardt, Udo [Forschungszentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. for Safety Research; Keller, Werner [Studsvik GmbH und Co. KG, Stutensee (Germany)

2008-07-01

The paper presents first results of the post mortem investigations performed at the reactor pressure vessels (RPV) of the Russian WWER-440 type reactors. Trepans were taken from the core weld SN0.1.4 and base metal of the unit 1 RPV. This RPV was annealed after 15 years of operation and operated for two more years. At first the trepan of the core welding seam was investigated by Master Curve (MC) testing. Specimens from 5 locations through the thickness of the welding seam were tested according to ASTM E1921-05. The reference temperature T{sub 0} was calculated with the measured fracture toughness values, K{sub Jc}, at brittle failure of the specimen. Generally the K{sub Jc} values measured on pre-cracked and side-grooved Charpy size SE(B) specimens of the investigated weld metal follow the course of the Master Curve. The K{sub Jc} values show a remarkable scatter. More values than expected lie below the 5% fractile. In addition the MC SINTAP procedure was applied to determine T{sub 0}{sup SINTAP} of the brittle fraction of the data set. There are remarkable differences between T{sub 0} and T{sub 0}{sup SINTAP} indicating macroscopic inhomogeneous weld metal. The highest T{sub 0} was about 50 C at a distance of 22 mm from the inner surface of the weld. It is 40 K higher compared with T{sub 0} at the inner surface. This is important for the assessment of ductile-to-brittle temperatures measured with sub size Charpy specimens made of weld metal from the inner RPV wall. This material may not represent the most conservative condition. The results presented in this paper show that the Master Curve approach as adopted in the test standard ASTM E1921-05 is applicable to the investigated WWER-440 multilayer weld metal. The results are of direct importance for an advanced WWER-440 RPV integrity assessment. On the other hand the data pool is broadened for a general introduction of the MC based RPV integrity assessment in the national codes. Furthermore general experiences in

TORT application in reactor pressure vessel neutron flux calculations

International Nuclear Information System (INIS)

Belousov, S.I.; Ilieva, K.D.; Antonov, S.Y.

1994-01-01

The neutron flux values onto reactor pressure vessel for WWER-1000 and WWER-440 reactors, at the places important for metal embrittlement surveillance have been calculated by 3 dimensional code TORT and synthesis method. The comparison of the results received by both methods confirms their good consistency. (authors). 13 refs., 4 tabs

Crack growth behaviour of low-alloy steels for pressure boundary components under transient light water reactor operating conditions - CASTOC, Part II: WWER conditions

Energy Technology Data Exchange (ETDEWEB)

Ernestova, M.; Zamboch, M. [Nuclear Research Institute, NRI, Rez (Czech Republic); Devrient, B.; Roth, A. [Framatome ANP GmbH, Erlangen (Germany); Ehrnsten, U. [VTT Industrial Systems, Espoo (Finland); Foehl, J.; Weissenberg, T. [Staatliche Materialpruefungsanstalt, MPA, Stuttgart (Germany); Gomez-Briceno, D.; Lapena, J. [Centro de Investigaciones Energeticas Medioambientales y Tecnologicas, CIEMAT, Madrid (Spain); Ritter, S.; Seifert, H.P. [Paul Scherrer Institute, PSI, Villigen (Switzerland)

2004-07-01

One of the ageing phenomena of pressure boundary components of light water reactors (LWRs) is environmentally-assisted cracking (EAC). The project CASTOC (5. Framework Programme of the EU) was launched September 2000 with six European partners and terminated August 2003. It focused in particular on the EAC behaviour of low-alloy steels (LAS) and to some extent to weld metal, heat affected zone and the influence of an austenitic cladding. The main objective was directed to the clarification of crack growth behavior of LAS in high-temperature water due to EAC under constant load (steady-state power operation), to study the effect of transient conditions (during operation or start-up/shut-down of a plant) using their impact on time-based and cycle-based crack growth rates and to a more detailed understanding of the acting mechanisms. Autoclave tests were performed with Western and Russian type reactor pressure vessel steels under simulated boiling water reactor (BWR)/normal water chemistry (NWC) and pressurized water reactor (WWER) conditions. The investigations were performed with fracture mechanics specimens of different sizes and geometries. The applied loading comprised cyclic loads, static loads and load spectra where the static load was periodically interrupted by partial unloading. With regard to water chemistry, the oxygen content (WWER) and impurities of sulphate and chlorides (BWR) were varied beyond allowable limits for continuous operation. The current paper summarizes the most important crack growth results obtained under simulated WWER conditions. The influence of oxygen content and the effect of specimen size (C(T)25 versus C(T)50 specimens) on the crack growth rates are shown. The results are discussed in the context of the current crack growth rate curves in the corresponding nuclear codes. (authors)

Crack growth behaviour of low-alloy steels for pressure boundary components under transient light water reactor operating conditions - CASTOC, Part II: WWER conditions

International Nuclear Information System (INIS)

Ernestova, M.; Zamboch, M.; Devrient, B.; Roth, A.; Ehrnsten, U.; Foehl, J.; Weissenberg, T.; Gomez-Briceno, D.; Lapena, J.; Ritter, S.; Seifert, H.P.

2004-01-01

One of the ageing phenomena of pressure boundary components of light water reactors (LWRs) is environmentally-assisted cracking (EAC). The project CASTOC (5. Framework Programme of the EU) was launched September 2000 with six European partners and terminated August 2003. It focused in particular on the EAC behaviour of low-alloy steels (LAS) and to some extent to weld metal, heat affected zone and the influence of an austenitic cladding. The main objective was directed to the clarification of crack growth behavior of LAS in high-temperature water due to EAC under constant load (steady-state power operation), to study the effect of transient conditions (during operation or start-up/shut-down of a plant) using their impact on time-based and cycle-based crack growth rates and to a more detailed understanding of the acting mechanisms. Autoclave tests were performed with Western and Russian type reactor pressure vessel steels under simulated boiling water reactor (BWR)/normal water chemistry (NWC) and pressurized water reactor (WWER) conditions. The investigations were performed with fracture mechanics specimens of different sizes and geometries. The applied loading comprised cyclic loads, static loads and load spectra where the static load was periodically interrupted by partial unloading. With regard to water chemistry, the oxygen content (WWER) and impurities of sulphate and chlorides (BWR) were varied beyond allowable limits for continuous operation. The current paper summarizes the most important crack growth results obtained under simulated WWER conditions. The influence of oxygen content and the effect of specimen size (C(T)25 versus C(T)50 specimens) on the crack growth rates are shown. The results are discussed in the context of the current crack growth rate curves in the corresponding nuclear codes. (authors)

Safeguarding the nuclear safety of WWER-440 reactor pressure vessels at SKODA Plzen

International Nuclear Information System (INIS)

Hrbek, Z.

1986-01-01

The approach is described of the SKODA enterprise to safety assurance and to providing the reliability of WWER-440 reactor pressure vessels. The philosophy is analyzed of in-service inspection and determination of the residual service life of pressure vessels. This follows up on the so-called conception of basic safety whose main aim is to preclude failures at production stage by the selection of suitable material, namely by optimizing the choice of raw materials, of metallurgical procedures such as will lead to high purity of the pressure vessel material, by introducing multiple inspection in production, reducing the sensitivity of materials to technological operations, and by high-quality welds. The quality of in-service inspections is given by the use of technical diagnostic instruments of peak quality and of modern methods of nondestructive materials testing. The instruments and methods used are described. It is stated that the experience gained with in-service inspection will make it possible to draw up operating regulations and safety criteria for nuclear installations and own inspection regulations, this with regard to technical and economic factors. (Z.M.)

Design of the WWER-440 pressurizer

International Nuclear Information System (INIS)

Bednarek, L.

1978-01-01

The main specifications are presented of a pressurizer for the WWER-440 reactor as are factors securing operating reliability and the required life of the equipment. Ferritic-pearlite steel 22K is the basic material for the manufacture of the shell, support and couplings. The internal parts and the heads are manufactured from the 08KH18N10T chromium-nickel austenitic steel, the bolts and nuts of manholes from chromium-molybdenum steels 25KH1MF and 25KH2MFA. Quality testing of basic materials and quality control during the process of manufacture are briefly described. (Z.M.)

Method of determination of thermo-acoustic coolant instability boundaries in reactor core at NPPs with WWER

International Nuclear Information System (INIS)

Skalozubov, Volodymyr; Kolykhanov, Viktor; Kovryzhkin, Yuriy

2007-01-01

The regulatory body of Ukraine, the National Atomic Energy Company and the Scientific and Production Centre have led team-works concerned with previously unstudied factors or phenomena affecting reactor safety. As a result it is determined that the thermo-acoustic coolant instability conditions can appear in the core at definite operating WWER regimes. Considerable cyclic dynamic loads affect fuel claddings over thermo-acoustic pressure oscillations. These loads can result in inadmissible cassette design damage and containment damage. Taking into account calculation and experimental research authors submit a method of on-line assessment of WWER core state concerning thermo-acoustic coolant instability. According to this method, the thermo-acoustic coolant instability appearance conditions can be estimated using normal registered parameters (pressure, temperature, heat demand etc.). At operative modes, a WWER-1000 core is stable to tracheotomies oscillations, but reduction of coolant discharge through the core for some times can result in thermo-acoustic coolant instability. Thermo-acoustic instability appears at separate transitional modes concerned with reactor scram and unloading/loading at all power units. When thermo-acoustic instability begins in transitional modes, core elements are under influence of high-frequency coolant pressure pulsations for a long time (tens of hours)

Problem Oriented Neutron-Gamma Cross Sections Libraries for WWER-440 and WWER-1000 Shielding and Reactor Vessel Dosimetry Application

International Nuclear Information System (INIS)

Belousov, S.; Antonov, S.; Ilieva, K.

1997-01-01

The 47 neutron and 20 gamma group libraries BGL-440 and BGL-1000 for the shielding and reactor vessel dosimetry application have been generated for WWER-440 and WWER-1000 by collapsing the VITAMIN-B6 library (199 neutron and 42 gamma groups on the base of ENDF/B-6). The first parts of the libraries for neutron-gamma transport calculation, BGL-440-1 (150 nuclides) and BGL-1000-1 (140 nuclides), have been generated by a modified version of SAS1X control module of the SCALE system. The appropriate zone-average neutron flux had been used for these sub-libraries collapsing. The BGL-440-2 and BGL-1000-2 sub-libraries consist of cross sections for all 120 nuclides of VITAMIN-B6, for calculation of the transport through non-reactor materials of dosimeters, capsules, specimens which may be placed in the cavity behind the reactor vessel. The neutron spectrum just beyond the RPV had been used for this collapsing. As the first test the comparative calculations of the neutron flux on/behind the WWER-1000 reactor vessel have been realised using the libraries BGL-1000 and BUGLE, intended for the American PWR reactors. The integral neutron flux values by BGL-1000 and BUGLE differ by 3% onto the vessel, and 5% behind the vessel. This result shows that the calculations of the neutron flux responses for the WWER vessel surveillance, especially in locations behind the WWER vessel have to be done by the appropriate BGL library. Key words: neutron transport, multigroup neutron cross section libraries

Project margins of advanced reactor design WWER-500

International Nuclear Information System (INIS)

Rogov, M.F.; Birukov, G.I.; Ershov, V.G.; Volkov, B.E.

1994-01-01

Project criteria for design of advanced WWER-500 reactor within design conditions are compared to the requirements of the Russian regulatory guides. Normal operation limits, safe operation limits for main anticipated operational occurrences and design limits accepted for design basis accidents are considered as in preliminary safety report. It is shown that the basic design criteria in the design of WWER-500 for the anticipated operational occurrences and for design basis accidents are more severe than required in the following regulatory guides General Safety Regulations for Nuclear Power Plants and Nuclear Safety Rules for Reactors of Nuclear Power Plants. This provides certain margins from safety point of view

WWER-440 type reactor core

International Nuclear Information System (INIS)

Mizov, J.; Svec, P.; Rajci, T.

1987-01-01

Assemblies with patly spent fuel of enrichment within 5 and 36 MWd/kg U or lower than the maximum enrichment of freshly charged fuel are placed in at least one of the peripheral positions of each hexagonal sector of the WWER-440 reactor type core. This increases fuel availability and reduces the integral neutron dose to the reactor vessel. The duration is extended of the reactor campaign and/or the mean fuel enrichment necessary for the required duration of the period between refuellings is reduced. Thus, fuel costs are reduced by 1 up to 3%. The results obtained in the experiment are tabulated. (J.B.). 1 fig., 3 tabs

Ensuring the operational safety of nuclear power plants with WWER reactors

International Nuclear Information System (INIS)

Shasharin, G.A.; Veretennikov, G.A.; Abagyan, A.A.; Lesnoj, S.A.

1984-01-01

At the start of 1983, 27 nuclear power producing units with reactor facilities of the WWER type were in operation in the Soviet Union and other countries. In 1982 the average load factor for nuclear power plants with WWER reactors was 73 per cent. There was not a single nuclear accident or even damage with any significant radiation consequences in the WWER reactors during the entire period of their operation. The most modern nuclear power plants with WWER-440 and WWER-1000 reactors meet all present-day international requirements. Safe operation of the plants is achieved by a variety of measures, the most important of which include: procedures for increasing the reliability of plant equipment and systems; ensuring exact compliance with plant operating instructions; ensuring reliable operation of plant safety systems; action directed towards maintaining the skills of plant personnel at a level adequate to ensure the taking of proper action during transient processes and accident situations. The paper discusses concrete steps for ensuring safe nuclear power plant operation along these lines. In particular, measures such as the following are described: the use of a system for collecting and processing information on equipment failures and defects; the development and introduction of methods of early defect diagnosis; the performance of complex testing of safety systems; the training of highly skilled personnel for nuclear power plants at educational combines and at teaching and training centres making use of simulators; arranging accident-prevention training and special instruction for personnel. (author)

Temperature etalon of WWER-440 reactor

International Nuclear Information System (INIS)

Stanc, S.; Slanina, M.

2001-01-01

The presentation deals with the description, parameters and advantages of use of the temperature etalon. The system ensures temperature measurement of reactor outlet and inlet temperatures with high accuracy. Accuracy of temperature measurement is 0.18 deg C, accuracy of temperature difference measurement is 0.14 deg C, both with probability 0.95. Using the temperature etalon it is possible to increase accuracy of the standard temperature reactor measurements and to check their accuracy in the course of power reactor statuses in every measurement cycle. Temperature reactor etalon was installed in 12 WWER-440 units in Slovakia, Bohemia and Bulgaria. (Authors)

Determination of neutron fluence and radiation brittleness temperature of WWER-440 and WWER-1000 pressure vessels in Kozloduy NPP

International Nuclear Information System (INIS)

Ilieva, K.; Apostolov, T.; Belousov, S.; Petrova, T.; Antonov, S.; Ivanov, K.; Prodanova, R.

1993-01-01

In Units 1-4 of Kozloduy NPP (WWER-440/230), the weld 4 of RPV undergoes the most severe irradiation embrittlement. Neither witness-samples, nor detectors are designed for these reactors. Transport calculations of fast neutron fluence on WWER-440 RPV and ex-vessel measurements by threshold activation detectors are the primary means for adequate assessment of metal state and for prognosis concerning the reactor life span. In WWER-1000 reactors (Units 5-6) the maximum neutron fluence occurs on the weld 3. The systematical observation of metal state is performed through witness-samples and threshold activation detectors ( 54 Fe (n,p), 63 Cu (n,α), 93 Nb (n,n')) placed above the reactor top edge and at the first vessel ring level. There are big differences in energy spectrum and integral neutron flux falling onto the weld 3, the RPV base metal and the staff detectors. This requires additional neutron measurements in the air gap between the RPV and the thermal insulation. (author)

Temperature and pressure instrumentation in WWERs and their testing

International Nuclear Information System (INIS)

Por, G.

1998-01-01

A description of WWER model V-213 reactors of second generation is presented and compared to analogous NPPs including description of temperature and pressure instrumentation which was tested at Paks NPP. From the experimental results it was concluded that measured response of in core neutron detector to bubbles strongly depends on the relative position of detector and point bubble injection. Neutron noise spectra show characteristic sink when the origin of bubbles is close to the detectors. Dependence of phase behaviour on the boiling conditions is included as well

Use of the Benchmarking System for Operational Waste from WWER Reactors

International Nuclear Information System (INIS)

2017-06-01

The focus of this publication is on benchmarking low and intermediate level waste generated and managed during the normal operating life of a WWER, and it identifies and defines the benchmarking parameters selected for WWER type reactors. It includes a brief discussion on why those parameters were selected and their intended benchmarking benefits, and provides a description of the database and graphical user interface selected, designed and developed, including how to use it for data input and data analysis. The CD-ROM accompanying this publication provides an overview of practices at WWER sites, which were to a large extent prepared using the WWER BMS.

Calculational results for radiation embrittlement of WWER pressure vessel at the Kozloduy NPP

Energy Technology Data Exchange (ETDEWEB)

Apostolov, T; Ilieva, K; Petrova, T [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

1996-12-31

Determination of radiation impact on metal state in the case of WWER-440/230 is made only by calculation methods since a special sample-witness (SW) incorporation had not been implemented. In WWER-1000 reactors such SW are foreseen but their spots are high above the active core. This is why in both reactors the appliance of a calculational procedure for radiation embrittlement determination is compulsory. The authors propose such a procedure accounting for the change in critical temperature of neutron brittleness by the neutron fluence. The neutron fluence and the shift of critical embrittlement temperature have been calculated for the maximum overloaded location and for the weld metal of the Kozloduy-5 and Kozloduy-6 reactors (WWER-1000). The shift of critical temperature in weld 4 of the Units 1-4 (WWER-440) is plotted versus work cycles and compared to experimental values. 4 figs., 5 tabs.

WWER-1000 reactor simulator. Material for training courses and workshops. 2. ed

International Nuclear Information System (INIS)

2005-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series No.12, Reactor Simulator Development (2001). Course material for workshops using a pressurized water reactor (PWR) simulator developed for the IAEA by Cassiopeia Technologies Inc. of Canada is presented in the IAEA publication, Training Course Series No. 22, 2nd edition, Pressurized Water Reactor Simulator (2005) and Training Course Series No.23, 2nd edition, Boiling Water Reactor Simulator (2005). This report consists of course material for workshops using the WWER-1000 Reactor Department Simulator from the Moscow Engineering and Physics Institute, Russian Federation

Results of noise analysis in the WWER 440 - type nuclear power plant Dukovany

International Nuclear Information System (INIS)

Runkel, J.; Stegemann, D.; Fiedler, J.; Hrosso, P.; Figedy, S.; Sadilek, J.; Hulin, J.

1996-01-01

Results of a common work in the frame of scientific and technological cooperation between the Slovak Republic and Germany in the field of development of diagnostic methods to improve the safety and availability of WWER-type reactors are presented. Signals of the standard diagnostic instrumentation of the WWER-type reactors of units 1,2 and 4 at the nuclear power plant Dukovany (EDU) in Czech Republic were analyzed. Mechanical vibrations like pendular and vertical movements of the reactor pressure vessel and its internals as well as thermohydraulic fluctuations like fluid resonances or standing pressure waves could be identified in all the three units. Incipient changes of the mechanical and/or thermohydraulic conditions of the core can be detected by periodical analysis of the signals of the standard reactor instrumentation of WWER-types reactors. (authors)

New designs of medium power WWER reactor plants

International Nuclear Information System (INIS)

Ryzhov, S.B.; Mokhov, V.A.; Nikitenko, M.P.; Chetverikov, A.E.; Veselov, D.O.; Shchekin, I.G.; Petrov, V.V.

2010-01-01

The task of constructing NPPs as the objects of regional power industry is included into the Federal Target Program on nuclear power technologies of new generation for the period till 2020. Such NPPs are considered as perspective sources of energy for solution of the problems concerning provision of electric energy, household and industrial heat to the regions with limited capabilities of the power grid. OKB 'GIDROPRESS' present the conceptual study of RP design for the Unit of 600 MW (el.) power, taking into account their long-term experience in the field of development and operation of WWER reactor plants. Practical implementation of WWER-600 and WWER-300 RP designs seems to be feasible: practice in manufacturing the main equipment is available; cooperation of design, scientific organizations and manufacturers of equipment; is established; basic design solutions for equipment are of reference character

Study on the power control system for NPP power unit with the WWER-440 reactor

International Nuclear Information System (INIS)

Aleksandrova, N.D.; Naumov, A.V.

1981-01-01

Results of model investigations into basic version of the power control systems (PCS) conformably to the WWER-440 NPP power unit are stated. Transient processes in the power unit system when being two PCS versions during perturbations of different parameters: unit power, vapour pressure or position of control rods have been simulated. Investigations into the different PCS versions show that quality of operation of a traditional scheme with a turbine power controller and reactor pressure controller can be significantly improved with the introduction of a high-speed signal of pressure into the reactor controller. The PCS version with the compensation of interrelations between the turbine and reactor controllers constructed according to the same principles as the standard schemes of power units of thermal electric power plant is perspective as well [ru

Pressurized water reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA Training Course Series No. 12, 'Reactor Simulator Development' (2001). Course material for workshops using a WWER- 1000 reactor department simulator from the Moscow Engineering and Physics Institute, the Russian Federation is presented in the IAEA Training Course Series No. 21 'WWER-1000 Reactor Simulator' (2002). Course material for workshops using a boiling water reactor simulator developed for the IAEA by Cassiopeia Technologies Incorporated of Canada (CTI) is presented in the IAEA publication: Training Course Series No.23 'Boiling Water Reactor Simulator' (2003). This report consists of course material for workshops using a pressurized water reactor simulator

About reliability of WWER pressure vessel neutron fluence calculation

Energy Technology Data Exchange (ETDEWEB)

Belousov, S; Ilieva, K; Antonov, S [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

1996-12-31

This reliability study was carried out under a Research Contracts F111 and TH-324 of the Bulgarian Ministry of Higher Education and the IAEA. The effect of geometry approximation and the choice of neutron cross-sections on the calculation model is estimated. The neutron flux onto reactor pressure vessel at locations, important for metal embrittlement surveillance, has been calculated using the codes TORT and DORT. The flux values calculated for both WWER-440 and WWER-1000 show good consistency within the limits of solution accuracy. It is concluded that the synthesis method (DORT) can be used for calculations at a reasonable cost whenever metal embrittlement surveillance is considered. Using an iron sphere benchmark measurement, a comparison of an experimental leakage spectrum with spectrum calculated using multigroup neutron cross-sections based on ENDF/B-4 and ENDF/B-6 data is performed. In the energy region above 1 MeV the best agreement with the experiment is achieved for ENDF/B-6 in VITAMIN-E group structure. 7 refs., 1 fig., 4 tabs.

About reliability of WWER pressure vessel neutron fluence calculation

International Nuclear Information System (INIS)

Belousov, S.; Ilieva, K.; Antonov, S.

1995-01-01

This reliability study was carried out under a Research Contracts F111 and TH-324 of the Bulgarian Ministry of Higher Education and the IAEA. The effect of geometry approximation and the choice of neutron cross-sections on the calculation model is estimated. The neutron flux onto reactor pressure vessel at locations, important for metal embrittlement surveillance, has been calculated using the codes TORT and DORT. The flux values calculated for both WWER-440 and WWER-1000 show good consistency within the limits of solution accuracy. It is concluded that the synthesis method (DORT) can be used for calculations at a reasonable cost whenever metal embrittlement surveillance is considered. Using an iron sphere benchmark measurement, a comparison of an experimental leakage spectrum with spectrum calculated using multigroup neutron cross-sections based on ENDF/B-4 and ENDF/B-6 data is performed. In the energy region above 1 MeV the best agreement with the experiment is achieved for ENDF/B-6 in VITAMIN-E group structure. 7 refs., 1 fig., 4 tabs

Databases on safety issues for WWER and RBMK reactors. Users' manual. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1996-04-01

At the beginning of the IAEA Extrabudgetary Programme on the safety of WWER reactors a great number of findings and recommendations (safety items) were collected as a result of design review and safety review missions of the WWER-440/230 type reactors. On the basis of these findings a technical database containing more than 1300 records was established to support the consolidation of the information obtained and to help in identification of safety issues. After the scope of the WWER extrabudgetary programme was extended similar data sets were prepared for the WWER-440/213, WWER-1000 and RBMK nuclear power plants. This publication describes the structure of the databases on safety issues of WWER and RBMK NPPs, the information sources used in the databases and interrogation capabilities for users to obtain the necessary information. 14 refs, 9 figs, 5 tabs

Enhanced Westinghouse WWER-1000 fuel design for Ukraine reactors

International Nuclear Information System (INIS)

Dye, M.; Shah, H.

2015-01-01

Westinghouse has completed design, development, and region quantity delivery of an enhanced Westinghouse fuel assembly for WWER-1000 reactors to support continued safe reactor operations. The enhanced design builds on the successful performance of an earlier generation design which has operated in the South Ukraine 3 reactor for multiple cycles without any fuel rod failures. Incorporated design enhancements include a thicker spacer grid outer strap, an enhanced spacer grid outer strap profile to limit the risk for, and impact of, mechanical interaction/interference with coresident fuel, an all Alloy 718 grid structure for improved stability and strength, and improvements to the top and bottom nozzles. Capable of meeting increased lateral loads generated from using a higher axial trip limit for the refueling machine crane, the design was verified by extensive mechanical and thermalhydraulic testing, which included a newly developed fuel assembly-to-fuel assembly handling test rig to assess performance during bounding core loading and unloading conditions. Through these extensive design enhancements and comprehensive testing program, the enhanced WWER-1000 design provides additional performance, handling, and reliability margins for safe reactor operation. (authors)

Numerical effects in the neutron flux calculations into WWER-type reactor vessels using the Monte Carlo

International Nuclear Information System (INIS)

Garcia Yip, F.; Alvarez Cardona, C.M.; Rodriguez Gual, M.; Hernandez Valle, S.

2000-01-01

In the present paper, a PC version of the Monte Carlo 3-D HEXANN-EVALU system is used for the estimation of the WWER reactor pressure vessel irradiation. It was selected on the basis of its flexible options that, however, need to be quantified in connection with the desired magnitudes. The parameters that control the random walk of neutrons, as well as the efficiency increasing options included in the code, are studied in order to identify their impact on the final results for fluxes and fluence in the reactor pressure vessel. As a result, an optimal set of parameters is suggested. (authors)

Experience of developing the imitators of the fuel element for the WWER reactors

International Nuclear Information System (INIS)

Balashov, S.M.; Boltenko, Eh.A.; Vinogradov, V.A.

1998-01-01

Peculiarities of designs of fuel elements imitators for the WWER-type reactors of nominal capacity and with single-ended current feed positioning are considered. The data on the filler heat conductivity and the results of tests and application of the fuel elements imitators at various testing facilities are presented. The possibility of equipping one of the non operating WWER reactors with the fuel element imitators for conduct of large-scale experiment is indicated

Consideration of severe accidents in design of advanced WWER reactors

International Nuclear Information System (INIS)

Fedorov, V.G.; Rogov, M.F.; Podshibyakin, A.K.; Fil, N.S.; Volkov, B.E.; Semishkin, V.P.

1998-01-01

Severe accident related requirements formulated in General Regulations for Nuclear Power Plant Safety (OPB-88), in Nuclear Safety Regulations for Nuclear Power Stations' Reactor Plants (PBYa RU AS-89) and in other NPP nuclear and radiation guides of the Russian Gosatomnadzor are analyzed. In accordance with these guides analyses of beyond design basis accidents should be performed in the reactor plant design. Categorization of beyond design basis accidents leading to severe accidents should be made on occurrence probability and severity of consequences. Engineered features and measures intended for severe accident management should be provided in reactor plant design. Requirements for severe accident analyses and for development of measures for severe accident management are determined. Design philosophy and proposed engineered measures for mitigation of severe accidents and decrease of radiation releases are demonstrated using examples of large, WWER-1000 (V-392), and medium size WWER-640 (V-407) reactor plant designs. Mitigation of severe accidents and decrease of radiation releases are supposed to be conducted on basis of consistent realization of the defense in depth concept relating to application of a system of barriers on the path of spreading of ionizing radiation and radioactive materials to the environment and a set of engineered measures protecting these barriers and retaining their effectiveness. Status of fulfilled by OKB Gidropress and other Russian organizations experimental and analytical investigations of severe accident phenomena supporting design decisions and severe accident management procedures is described. Status of the works on retention of core melt inside the WWER-640 reactor vessel is also characterized

Review of WWER fuel and material tests in the Halden reactor

International Nuclear Information System (INIS)

Volkov, B.; Kolstad, E.

2006-01-01

A review of the tests with WWER fuels and materials conducted in HBWR over the years of cooperation with Russia is presented. The first test with old generation WWER-440 fuel and PWR specification fuel was carried out from 1995 to 1998. Some differences between these fuels regarding irradiation induced densification and pellet design as well as similar fuel thermal behaviour, swelling and FGR were revealed during the test. The data from this test are reviewed and compared with PIE recently performed to confirm the in-pile measurements. The second test was started in March 1999 with the main objective to study different modified WWER fuels also in comparison with PWR fuel. The results indicated that all these modified WWER fuels exhibit improved densification properties relative to earlier tested fuel. In-pile data on fuel densification have been analysed with respect to as fabricated fuel microstructure and can be used for verification of fuel behaviour models. Corrosion and creep tests in the Halden reactor encompass WWER cladding alloys and some results are given. Prospective WWER fuel and material tests foreseen within the frame of the joint program of OECD HRP are also presented. (authors)

Water chemistry in WWER reactors

International Nuclear Information System (INIS)

Yurmanov, V.A.; Mamet, V.A.; Shestakov, Yu.M.; Amosov, M.M.

1997-01-01

In this paper ''Water Chemistry in WWER Reactors'', are briefly described the 30 WWERs in Russian and the Ukraine, and are pointed out the essential differences between the 440s and 1000s. The primary coolant in the six loops of the former type operates at 270-290 deg. C, while the four loops of the latter type are at 290-320 deg. C. Performance of the fuel has been generally good with some fission product activities emanating from tramp uranium. Incidents causing unusually high fission product levels were overheating of the 16th fuel load at Kola NPP in 1990 by a reduced coolant flow, and fuel defects at Novovoronezh NPP resulting from deposits of carbon and corrosion products. Organic carbon, depositing from the coolant in regions of high turbulence (i.e. at the spacer grids), provokes corrosion product deposition. The source of the organic is not known. New chemistry guidelines have been implemented since 1992-93 for Russian and Ukrainian WWERs. These include higher pH T values (7.0-7.1 as opposed to 6.6-6.9) and tighter controls on oxygen and impurities. Lower dose rates in steam generator channels are reported. Significant reduction in operator doses are achieved by these methods coupled with a ''soft decontamination'' involving changing the KOH concentration and, hence, the pH T before shutdown. The benefits of hydrazine treatment for deoxygenating feedwater and coolant prior to start up, for injecting before shutdown and for general chemistry control on radiation fields are described. (author). 7 refs, 9 figs, 8 tabs

Water chemistry in WWER reactors

Energy Technology Data Exchange (ETDEWEB)

Yurmanov, V A; Mamet, V A; Shestakov, Yu M; Amosov, M M [All-Russian Scientific Research Inst. for Nuclear Power Plants Operation, Moscow (Russian Federation)

1997-02-01

In this paper ``Water Chemistry in WWER Reactors``, are briefly described the 30 WWERs in Russian and the Ukraine, and are pointed out the essential differences between the 440s and 1000s. The primary coolant in the six loops of the former type operates at 270-290 deg. C, while the four loops of the latter type are at 290-320 deg. C. Performance of the fuel has been generally good with some fission product activities emanating from tramp uranium. Incidents causing unusually high fission product levels were overheating of the 16th fuel load at Kola NPP in 1990 by a reduced coolant flow, and fuel defects at Novovoronezh NPP resulting from deposits of carbon and corrosion products. Organic carbon, depositing from the coolant in regions of high turbulence (i.e. at the spacer grids), provokes corrosion product deposition. The source of the organic is not known. New chemistry guidelines have been implemented since 1992-93 for Russian and Ukrainian WWERs. These include higher pH{sub T} values (7.0-7.1 as opposed to 6.6-6.9) and tighter controls on oxygen and impurities. Lower dose rates in steam generator channels are reported. Significant reduction in operator doses are achieved by these methods coupled with a ``soft decontamination`` involving changing the KOH concentration and, hence, the pH{sub T} before shutdown. The benefits of hydrazine treatment for deoxygenating feedwater and coolant prior to start up, for injecting before shutdown and for general chemistry control on radiation fields are described. (author). 7 refs, 9 figs, 8 tabs.

Recommended reactor coolant water chemistry requirements for WWER-1000 units with 235U higher enriched fuel

International Nuclear Information System (INIS)

Dobrevski, I.; Zaharieva, N.

2011-01-01

The last decade worldwide experience of PWRs and WWERs confirms the trends for the improvement of the nuclear power industry electricity production through the implementation of high burn-up or high fuel duty, which are usually accompanied with the usage of UO 2 fuel with higher content of 235 U - 4.0% - 4.5% (5.0%). It was concluded that the onset of sub-cooled nucleate boiling (SNB) on the fuel cladding surfaces and the initial excess reactivity of the core are the primary and basic factors accompanying the implementation of uranium fuel with higher 235 U content, aiming extended fuel cycles and higher burn-up of the fuel in Pressurized Water Reactors. As main consequences of the presence of these factors the modifications of chemical / electrochemical environments of nuclear fuel cladding- and reactor coolant system- surfaces are evaluated. These conclusions are the reason for: 1) The determination of the choices of the type of fuel cladding materials in respect with their enough corrosion resistance to the specific fuel cladding environment, created by the presence of SNB; 2) The development and implementation of primary circuit water chemistry guidelines ensuring the necessary low corrosion rates of primary circuit materials and limitation of cladding deposition and out-of-core radioactivity buildup; 3) Implementation of additional neutron absorbers which allow enough decrease of the initial concentration of H 3 BO 3 in coolant, so that its neutralization will be possible with the permitted alkalising agent concentrations. In this paper the specific features of WWER-1000 units in Bulgarian Nuclear Power Plant; use of 235 U higher enriched fuel in the WWER-1000 reactors in the Kozloduy NPP; coolant water chemistry and radiochemistry plant data during the power operation period of the Kozloduy NPP Unit 5, 15 th fuel cycle; evaluation of the approaches and results by the conversion of the WWER-1000 Units at the Kozloduy NPP to the uranium fuel with 4.3% 235 U as

Fracture analyses of WWER reactor pressure vessels

International Nuclear Information System (INIS)

Sievers, J.; Liu, X.

1997-01-01

In the paper first the methodology of fracture assessment based on finite element (FE) calculations is described and compared with simplified methods. The FE based methodology was verified by analyses of large scale thermal shock experiments in the framework of the international comparative study FALSIRE (Fracture Analyses of Large Scale Experiments) organized by GRS and ORNL. Furthermore, selected results from fracture analyses of different WWER type RPVs with postulated cracks under different loading transients are presented. 11 refs, 13 figs, 1 tab

Fracture analyses of WWER reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Sievers, J; Liu, X [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Koeln (Germany)

1997-09-01

In the paper first the methodology of fracture assessment based on finite element (FE) calculations is described and compared with simplified methods. The FE based methodology was verified by analyses of large scale thermal shock experiments in the framework of the international comparative study FALSIRE (Fracture Analyses of Large Scale Experiments) organized by GRS and ORNL. Furthermore, selected results from fracture analyses of different WWER type RPVs with postulated cracks under different loading transients are presented. 11 refs, 13 figs, 1 tab.

Radiation damage structure in irradiated and annealed 440 WWER-Type reactor pressure vessel steels

International Nuclear Information System (INIS)

Kocik, J.; Keilova, E.

1993-01-01

A review of irradiation damages in WWER-type RPV steels based on conventional Transmission Electron Microscopy investigations in a power reactor and a research reactor, is presented; the samples consist in Cr-Mo-V ferritic steel (15Kh2MFA type). The visible part of radiation-induced defects consists of very fine vanadium carbide precipitates, small dislocation loops and black dots (presumably corresponding to clusters and particle embryos formed from vacancies and solute-atoms (vanadium, copper, phosphorus) and carbon associated with vanadium. Radiation-induced defects are concentrated at dislocation substructure during irradiation in a power reactor, revealing the role of radiation-enhanced diffusion in damage structure forming process. Contrarily, the distribution of defects resulting from annealing of specimens irradiated in the research reactor is pre-determined by an homogenous distribution of radiation-induced defects prior to annealing. Increasing the number of re-irradiation and annealing cycles, the amount of dislocation loops among all defects seems to be growing. Simultaneously, the dislocation substructure recovers considerably. (authors). 14 refs., 11 figs., 3 tabs

Radiation damage structure in irradiated and annealed 440 WWER-Type reactor pressure vessel steels

Energy Technology Data Exchange (ETDEWEB)

Kocik, J; Keilova, E [Czech Nuclear Society, Prague (Czech Republic)

1994-12-31

A review of irradiation damages in WWER-type RPV steels based on conventional Transmission Electron Microscopy investigations in a power reactor and a research reactor, is presented; the samples consist in Cr-Mo-V ferritic steel (15Kh2MFA type). The visible part of radiation-induced defects consists of very fine vanadium carbide precipitates, small dislocation loops and black dots (presumably corresponding) to clusters and particle embryos formed from vacancies and solute-atoms (vanadium, copper, phosphorus) and carbon associated with vanadium. Radiation-induced defects are concentrated at dislocation substructure during irradiation in a power reactor, revealing the role of radiation-enhanced diffusion in damage structure forming process. Contrarily, the distribution of defects resulting from annealing of specimens irradiated in the research reactor is pre-determined by an homogenous distribution of radiation-induced defects prior to annealing. Increasing the number of re-irradiation and annealing cycles, the amount of dislocation loops among all defects seems to be growing. Simultaneously, the dislocation substructure recovers considerably. (authors). 14 refs., 11 figs., 3 tabs.

Safety problems of nuclear power plants with reactors of new generation; Voprosy bezopasnosti v proehktakh AEhS novogo pokoleniya s WWER

Energy Technology Data Exchange (ETDEWEB)

Fedorov, V; Rogov, M; Biryukov, G [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1996-12-31

Modernization schemes for safety enhancement of WWER-1000 reactors are proposed. In the case of WWER-1000/V-392 it is based on introduction of additional safety systems and overall design improvement. For WWER-1100 (1000-1100 MW) the safety is enhanced by passive systems built from two-stage heat exchangers. For WWER-500/600 the use of passive safety system is extended to emergency cooling of the active zone and removal of the residual heat emissions from the reactor. The technical characteristics of the three reactors are compared. 3 figs., 1 tab.

Pressurized water reactor simulator. Workshop material. 2. ed

International Nuclear Information System (INIS)

2005-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development. And the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA Training Course Series No. 12, 'Reactor Simulator Development' (2001). Course material for workshops using a WWER- 1000 reactor department simulator from the Moscow Engineering and Physics Institute, the Russian Federation is presented in the IAEA Training Course Series No. 21, 2nd edition, 'WWER-1000 Reactor Simulator' (2005). Course material for workshops using a boiling water reactor simulator developed for the IAEA by Cassiopeia Technologies Incorporated of Canada (CTI) is presented in the IAEA publication: Training Course Series No.23, 2nd edition, 'Boiling Water Reactor Simulator' (2005). This report consists of course material for workshops using a pressurized water reactor simulator

WWER reactor pressure vessel embrittlement knowledge - a way forward for consolidation

International Nuclear Information System (INIS)

Von Estorff, U.; Brumovsky, M.

2010-01-01

Many stakeholders, such as Institutes, R and D Organisations, Regulators, Utilities, Governmental Organisations, have recognised the need for collecting, preserving, consolidating (validating), and disseminating nuclear knowledge (documents, competences and data), in order to make it easily accessible to future generations through modern informatics tools and training and education measures. A broad spectrum of components and technologies should be considered, i.e. reactor pressure vessel (RPV), piping, internals, steam generator, etc. regarding knowledge, material data and practices. In the long run, it will also support future decommissioning exercises of nuclear installations as a valuable knowledge source. In addition to the knowledge in each Member State, the IE produced a long standing record of results from its own institutional activities and even more through the participation to a large number of European Network partnership projects. It is important, besides preservation, to consolidate the enormous amount of scientific results produced since. Therefore, the IE has developed a method for consolidation of nuclear knowledge. The method relays on the mobilisation of all identified leading experts in the EU in re-evaluating old knowledge and consolidating what is necessary to create training materials for the new generations. This method was applied for a pilot study for consolidating and preserving WWER RPV safety related knowledge, which is scattered in many countries and in different languages, facing a serious issue in terms of getting lost. This initiative could be the start of a wider Nuclear Knowledge Preservation and Consolidation activity. Experience gained and lessons learnt from the first exercise will be presented in this paper. (authors)

Organization and mechanization of maintenance operations at NPPs with the WWER type reactors

International Nuclear Information System (INIS)

Titov, A.A.

1983-01-01

The structure of capital investments defining organization and mechanization of maintepance operations at NPPs with the WWER type reactors is analyzed. The trends in development of optimum decisions for organization and mechanization of repair obs at NPPs being designed taking into account the prospects of nuclear powep enginerning development, the system of NPP maintenance servicing, as well as the structure of repair-productive capacities are discussed. On the basis of the analysis of the data obtained in designing the Zaporozhskaya NPP it is shown that the capital investments for organizing and mechanization of maintenance operations at the unified NPP site with four WWER-1000 reactors reach nearly 18 roubles/kW. A conclusion is drawn that at present the design of an NPP with the WWER-1000 reactor totally meets the requirements of realization of periodic maintenance operations. It is advisable to cooperate the NPP management with that of a thermal power station from the viewpoint of using manpower, which would improve the operating conditions and labour productivity of workers engaged in repair and, consequently, reduce the capital investments and repair expenditures

Influence of temperature measurement accuracy and reliability on WWER-440 reactor operation

International Nuclear Information System (INIS)

Petenyi, V.; Ricany, J.

2001-01-01

The WWER-440 reactor power is controlled by coolant heat-up measurements installed on hot and cold circulation loops (enthalpy rise). For power distribution determination the thermocouples installed in reactor vessel above the fuel assemblies are mainly utilised. The paper shortly presents some interesting observations of temperature measurements influencing the reactor power operation of revealed changes in reactor core behaviour. (Authors)

Examination of VVER-1000 Reactor Pressure Vessel

International Nuclear Information System (INIS)

Matokovic, A.; Picek, E.; Markulin, K.

2008-01-01

The increasing demand of a higher level of safety in the operation of the nuclear power plants requires the utilisation of more precise automated equipment to perform in-service inspections. That has been achieved by technological advances in computer technology, in robotics, in examination probe technology with the development of the advanced inspection technique and has also been due to the considerable and varied experience gained in the performance of such inspections. In-service inspection of reactor pressure vessel, especially Russian-designed WWER-1000 presents one of the most important and extensive examination of nuclear power plants primary circuit components. Such examination demand high standards of inspection technology, quality and continual innovation in the field of non-destructive testing advanced technology. A remote underwater contact ultrasonic technique is employed for the examination of the base metal of vessel and reactor welds, whence eddy current method is applied for clad surface examinations. Visual testing is used for examination of the vessel interior. The movement of inspection probes and data positioning are assured by using new reactor pressure vessel tool concept that is fully integrated with inspection systems. The successful performance of reactor pressure vessel is attributed thorough pre-outage planning, training and successful performance demonstration qualification of chosen non-destructive techniques on the specimens with artificial and/or real defects. Furthermore, use of advanced approach of inspection through implementation the state-of-the-art examination equipment significantly reduced the inspection time, radiation exposure to examination personnel, shortening nuclear power plant outage and cutting the total inspection costs. This paper presents advanced approach in the reactor pressure vessel in-service inspections and it is especially developed for WWER-1000 nuclear power plants.(author)

Activities in the Czech Republic for reactor pressure components lifetime management

International Nuclear Information System (INIS)

Brumovsky, M.

1995-01-01

Preparation of a system of regulatory guides for life assessment of main pressure components, for inspection qualification and demonstration programmes are outlined. Lifetime management programme for NPP with WWER-440/V-213 reactors is described. Figs and tabs

Main trends and content of works on fabrication of fuel rods with MOX fuel for the WWER-1000 reactor

International Nuclear Information System (INIS)

Tsykanov, V.A.; Golovanov, V.N.; Mayorshin, A.A.; Yurchenko, A.D.; Ilyenko, S.A.; Syuzev, V.N.

2000-01-01

The main trends of production of pellet MOX-fuel for the WWER reactors using the trial-experimental equipment at SSC RF RIAR are set forth. The main realized parameters of fabrication of MOX-fuel pellets are presented. The content of the reactor tests program is considered with allowance for their licensing requirements for the WWER reactors. (author)

Analyses and results from standard surveillance programmes of WWER 440/V-213C reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Falcnik, M; Brumovsky, M; Pav, T [Czech Nuclear Society, Prague (Czech Republic)

1994-12-31

In Czech and Slovak republics, six units of WWER 440/C type reactors are monitored by surveillance specimens programmes; the specimens are determined for static tensile testing, impact notch toughness testing and fracture toughness evaluation. Results of mechanical properties of these specimens after irradiation in intervals between 1 and 5 years of operation, are summarized and discussed with respect to the effect of individual heats and welded joints, radiation embrittlement, and annealing recovery. (authors). 3 refs., 11 figs., 2 tabs.

Experience and prospects of WWER-1000 reactor spent fuel transport

International Nuclear Information System (INIS)

Kondratyev, A.N.; Yershov, V.N.; Kozlov, Yu.V.; Kosarev, Yu.A.; Ilyin, Yu.V.; Pavlov, M.S.

1989-01-01

The paper deals with the USSR experience in shipping the commercial WWER-1000 reactor spent fuel in TK-10 and TK-13 casks. The cask designs, their basic characteristics and the WWER-1000 spent fuel features are described. An example of calculational/experimental approach in the design of a basket (one of the most important components) for spent fuel assembly (SFA) accommodation in a cask is given. The main problems of future development works are presented in brief. A concept of development of nuclear power industry with the closed fuel cycle is assumed in the Soviet Union, hence the spent nuclear fuel is to be transported from NPPs to reprocessing plants. To transport WWER-1000 spent fuel, the casks of two types were developed. These are: a pilot TK-10 cask of 3t capacity in fuel; a commercial TK-13 cask of ∼6t capacity in fuel. The pilot TK-10 cask is thick-walled (360mm) cylindrical vessel manufactured of steel shells and a bottom welded to each other. The material of the body is carbon steel. There is a steel jacket on the outer side of the cask body and at 120 mm distance off the bottom. On its cylindrical part between the jacket and the body there are T-shaped circular ribs acting as shock-absorbers. The space between the jacket and the body is filled with ethylene glycol solution of 65 degree C crystallization temperature, which functions as a neutron shielding. The TK-10 cask coolant is water or air (nitrogen) at minor excess pressure resulted from FA heatup after the cask sealing

Surveillance of WWER-440 fuel performance

International Nuclear Information System (INIS)

Simko, J.; Urban, P.

1999-01-01

In this lecture next problems of surveillance of WWER-440 fuel performance are presented: surveillance of WWER-440 fuel performance at Mochovce NPP; basic data of WWER-440 reactor; in-core reactor measuring system 'SVRK'; basic level of SVRK; information output of basic level of SVRK; surveillance of fuel performance; table of permissible operation conditions of the reactor; limitation of the unit 1 power at the beginning of the operation; cyclic changes of power; future perspectives

Comparison of fuel cycles characteristics for nuclear energy systems based on WWER-TOI and BN-1200 reactors

International Nuclear Information System (INIS)

Kagramanyan, V.S.; Kalashnikov, A.G.; Kapranova, Eh.N.; Puzakov, A.Yu.

2014-01-01

Authors determine the characteristics of the fuel cycle (FC) based on stationary nuclear power system based on WWER-TOI and BN-1200 reactors with fuel of different composition. Characteristics of reactor systems with partial or complete spent nuclear fuel reprocessing and recycling of plutonium are compared to those of the reference system consisting only of WWER-TOI with uranium oxide fuel, operating in an open FC [ru

Reactor noise analysis applications and systems in WWER-440 and WWER-1000 type PWRs

International Nuclear Information System (INIS)

Por, G.

1998-01-01

This paper presents an introduction on different types of well selected noise diagnostic methods with their occurrence in WWER reactors with an analysis of their impact on operational safety and aging which affects the installations safety as well. The main objective is to attract the attention of NPP management staff dealing with safety, safety culture, maintenance, operation and quality assurance proving that such methods can give benefit not only to economy but impact safety of nuclear installations

ACT-1000. Group activation cross-section library for WWER-1000 type reactors

Energy Technology Data Exchange (ETDEWEB)

Zolotarev, K I; Pashchenko, A B [National Research Centre - A.I. Leipunsky Institute for Physics and Power Engineering, Obninsk (Russian Federation)

2001-10-01

The ACT-1000, a problem-oriented library of group-averaged activation cross-sections for WWER-1000 type reactors, is based on evaluated microscopic cross-section data files. The ACT-1000 data library was designed for calculating induced activity for the main dose-generated nuclides contained in WWER-1000 structural materials. In preparing the ACT-1000 library, 47 group-averaged cross-section data for the 10{sup -9}-17.33 MeV energy range were used to calculate the spatial-energy neutron flux distribution. (author)

Electroerosion cutting of low-sized templets from WWER-1000 type reactor vessel

International Nuclear Information System (INIS)

Neklyudov, I.M.; Ozhigov, L.S.; Gozhenko, S.V.

2012-01-01

The article presents the results of developed method of electroerosion cutting of low-sized templets for the reactor vessel metal composition and structure control in laboratory environment. The article describes the equipment for the remote electroerosive cutting of templets from WWER-1000 type reactor vessel by rigid electrode. The testing results are also shown.

Study on steam separation in steam generators of a NPP with the WWER-440 reactors

International Nuclear Information System (INIS)

Dmitriev, A.I.; Kolzov, Yu.V.; Titov, V.F.; Dubrovin, A.V.; Ilyushin, V.F.; Volkov, A.P.

1977-01-01

The separation characteristics as well as the actual level position in steam generators with and without a submerged holy sheet have been determined at a WWER-440 reactor nuclear power plant. It has been shown, that without changing the design of steam generators their load at the WWER-440 reactor nuclear power plant can be increased by about 10%. In this case the vapour humidity does not exceed the permissible value equal to 0.25%. The submerged holy sheet considerably decreases load irregularity and swelling of the water-steam mixture layer

Calculation of fluences of fast neutrons hitting the pressure vessel of the Dukovany NPP WWER-440 reactor. Part I. Theory, calculations, comparison with the experiment

International Nuclear Information System (INIS)

Rataj, J.

1993-10-01

The method of calculating neutron spectra and integral flux densities of neutrons hitting the pressure vessel of the Dukovany NPP WWER-440 reactor is outlined. The one-dimensional and two-dimensional calculations were performed by means of the DORT code in R, R-Z, and R-Θ geometries using the cross sections from the ELXSIR library. In the R-Θ geometry, the coupled neutron flux densities were determined. The calculated values of the maximum activation of detectors differ less than 15% from the values measured in surveillance specimens, which is within the limit of uncertainty associated with the position of the detector in the casing. The differences between the calculated and observed data behind the pressure vessel were below 4%. 10 tabs., 3 figs., 41 refs

Effect of high-temperature filtration on impurity composition in the primary circuit coolant of power units with WWER-1000 reactors

International Nuclear Information System (INIS)

Efimov, A.A.; Moskvin, L.N.; Gusev, B.A.; Leont'ev, G.G.; Nekrest'yanov, S.N.

1992-01-01

The effects of high-temperature filtration on changes in dispersive, chemical, radioisotope and phase compositions of impurities in primary circuit coolant of NPP with the WWER-1000 reactor are studied. Special filters are used for the studies. The data obtained confirm the applicability of high-temperature filtration for purification of WWER reactor water and steam separators at NPPs with RBMK reactors

Benchmarking of multigroup neutron cross sections libraries on neutron transmission through WWER-440 vessel

International Nuclear Information System (INIS)

Ilieva, K.; Belousov, S.; Apostolov, T.

1998-01-01

The verification of calculated neutron fluence onto the WWER-440/230 pressure vessel is very topical task in particular referring that some of this type of reactors have been operated the major part of its design lifetime. Since the induced activity from the neutron irradiation onto the elements is a simple response of neutron flux the neutron fluence verification usually is done using the measured activity of radionuclides produced during reactor operation. Calculational and experimental results of 54 Mn induced activity of scraps from inner wall of Unit 1 reactor pressure vessel after 18th cycle and detectors irradiated behind the vessel during the 18th cycle of Unit 1 at Kozloduy NPP as well as neutron flux attenuation through the WWER-440/230 pressure vessel are presented. Neutron cross sections libraries generated on the base of ENDF/B-IV and ENDF/B-VI have been used in the calculations. The comparative analysis of evaluated activities and attenuation coefficient demonstrates the better reliability of the neutron fluence calculations by the libraries based on ENDF/B-VI than by ones on ENDF/B-IV. The extreme rarity of data for the activity of scraps from the WWER-440 reactor vessel and its combination with the data for the detectors irradiated behind the vessel makes them especially attractive for verification of calculational methods of neutron fluence onto the WWER-440 vessel with dummy cassettes loading. (author)

Saturated steam turbines for power reactors of WWER-type

International Nuclear Information System (INIS)

Czwiertnia, K.

1978-01-01

The publication deals with design problems of large turbines for saturated steam and with problem of output limitations of single shaft normal speed units. The possibility of unification of conventional and nuclear turbines, which creates the economic basis for production of both types of turbines by one manufacturer based on standarized elements and assemblies is underlined. As separate problems the distribution of nuclear district heating power systems are considered. The choice of heat diagram for district heating saturated steam turbines, the advantages of different diagrams and evaluaton for further development are presented. On this basis a program of unified turbines both condensing and district heating type suitable for Soviet reactors of WWER-440 and WWER-1000 type for planned development of nuclear power in Poland is proposed. (author)

Nuclear power plants with reactors WWER-1000 type: today and tomorrow; AEhS s WWER-1000: nastoyashchee i budushchee

Energy Technology Data Exchange (ETDEWEB)

Molchanov, V; Biryukov, G; Novak, K [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1996-12-31

There are currently 19 NPP units based on WWER-1000 reactors working in Russia, Ukraine and Bulgaria. They are of four types: V-187, V-302, V-338, V-320. The design principles of these reactors comply with regulations of the eighties, and it is necessary to introduce improvements according to the new regulations and to the operation experience gained. Two approaches for safety and efficiency enhancement are described: AS-91 and AS-92. AS-91 implies gradual improvement of the base WWER-1000/V-320 design by incorporation of new design solutions avoiding the need of building large scale models. AS-92 refers to entirely new design which require experimental research by building a full scale models or by using natural stands. The latter approach will be used for NPP projects to be built after year 2000. The main new feature of AS-92 is the addition of passive safety systems to the active ones in order to protect the fuel from damage.

Testing of acoustic emission method during pressure tests of WWER-440 steam generators and pressurizers

International Nuclear Information System (INIS)

Wuerfl, K.; Crha, J.

1987-01-01

The results are discussed of measuring acoustic emission in output pressure testing of steam generators and pressurizers for WWER-440 reactors. The objective of the measurements was to test the reproducibility of measurements and to find the criterion which would be used in assessing the condition of the components during manufacture and in operation. The acoustic emission was measured using a single-channel Dunegan/Endevco apparatus and a 16-channel LOCAMAT system. The results showed that after the first assembly, during a repeat dismantle of the lids and during seal replacement, processes due to seal contacts and bolt and washer deformations were the main source of acoustic emission. A procedure was defined of how to exclude new acoustic emission sources in such cases. The acoustic emission method can be used for the diagnostics of plastic deformation processes or of crack production and propagation in components during service. (Z.M.)

Gamma-radiation effect on diamond and steel during their irradiation in WWER type reactors

International Nuclear Information System (INIS)

Nikolaenko, V.A.; Karpukhin, V.I.; Amaev, A.D.; Vikhrov, V.I.; Korolev, Yu.N.; Krasikov, E.A.

1996-01-01

A study is made into the influence of reactor gamma radiation on expansion of crystal lattice in diamond. The data obtained are compared to those on radiation embrittlement of reactor vessel steels. The necessity of taking into consideration gamma radiation effects on WWER reactor vessel radiation resistance during long-term operation is shown [ru

A powerful methodology for reactor vessel pressurized thermal shock analysis

International Nuclear Information System (INIS)

Boucau, J.; Mager, T.

1994-01-01

The recent operating experience of the Pressurized Water Reactor (PWR) Industry has focused increasing attention on the issue of reactor vessel pressurized thermal shock (PTS). More specifically, the review of the old WWER-type of reactors (WWER 440/230) has indicated a sensitive behaviour to neutron embrittlement. This led already to some remedial actions including safety injection water preheating or vessel annealing. Such measures are usually taken based on the analysis of a selected number of conservative PTS events. Consideration of all postulated cooldown events would draw attention to the impact of operator action and control system effects on reactor vessel PTS. Westinghouse has developed a methodology which couples event sequence analysis with probabilistic fracture mechanics analyses, to identify those events that are of primary concern for reactor vessel integrity. Operating experience is utilized to aid in defining the appropriate event sequences and event frequencies of occurrence for the evaluation. Once the event sequences of concern are identified, detailed deterministic thermal-hydraulic and structural evaluations can be performed to determine the conditions required to minimize the extension of postulated flaws or enhance flaw arrest in the reactor vessel. The results of these analyses can then be used to better define further modifications in vessel and plant system design and to operating procedures. The purpose of the present paper will be to describe this methodology and to show its benefits for decision making. (author). 1 ref., 3 figs

Study on regimes of nuclear power plants with WWER-type reactors

International Nuclear Information System (INIS)

Akkerman, G.; Khampel', R.; Khentshel', G.; Kertsher, F.; Lyuttsov, K.

1976-01-01

The problems are considered of optimization of nuclear fuel loading, the peculiarities of the NPP operation at decreased power, and also the problem of stability operation of NPP with WWER type reactors taking into account specific features of these reactors (partial fuel overloads, change in reactor reactivity with power changes). The two particular interconnected problems discussed are: choice of such a sequence of partial rechargings which ensures the minimum cost of the electric power generated, and increasing the reactor operating time by reducing its power output. Besides the technical and economic estimates, much attention is given to analysing the stability of NPP operation

Optimization of design solutions on safety and economy for power unit of NPP with WWER reactor of new generation. Annex 8

International Nuclear Information System (INIS)

Krushelnitsky, V.N.; Berkovich, V.M.; Shvyrayev, Yu.; Podshebaykin, A.K.; Fil, N.S.

2002-01-01

Development of new generation WWER reactors is being carried out in Russia. These new projects with WWER reactors aim to achieve increased levels of safety and reduced costs. This paper describes these designs and discusses the main factors leading to the safety level increase and the improved economics. (author)

The international WWER fuel market

International Nuclear Information System (INIS)

Gingold, G.E.; Goldstein, L.; Strasser, A.A.

1994-01-01

The state of the world nuclear fuel market and its economic complexities are described. Currently the nuclear fuel market is oversupplied and nuclear fuel fabrication in the West far exceeds the anticipated demands. Actually the current demand is not much more than half of the capacity available to supply it. The Eastern Europe (excluding the plants in the Russian Federation) with its 20 WWER-440 and 12 WWER-1000 reactors in operation and additional 4 WWER-440 and 8 WWER-1000 units under construction is considered as a potential long-term market for the Western fuel fabricators. The following significant benefits of competition in the WWER fuel market for the operators of these reactors are : 1) lower cost; 2) more favorable contract terms and improved vendor cooperation with the customer; 3) accelerated technological development. A brief description of the main WWER fuel suppliers TVEL, ABB Atom, BNFL, EVF and Westinghouse, as well as the status of some new companies as CEZ and SEP is given. The principal differences between Western and WWER fuels are outlined. The advanced features offered by the Western vendors and Russian fuel supply organisations are discussed. 2 tabs., 1 fig

The international WWER fuel market

Energy Technology Data Exchange (ETDEWEB)

Gingold, G E; Goldstein, L; Strasser, A A [Stoller (S.M.) Corp., Pleasantville, NY (United States)

1994-12-31

The state of the world nuclear fuel market and its economic complexities are described. Currently the nuclear fuel market is oversupplied and nuclear fuel fabrication in the West far exceeds the anticipated demands. Actually the current demand is not much more than half of the capacity available to supply it. The Eastern Europe (excluding the plants in the Russian Federation) with its 20 WWER-440 and 12 WWER-1000 reactors in operation and additional 4 WWER-440 and 8 WWER-1000 units under construction is considered as a potential long-term market for the Western fuel fabricators. The following significant benefits of competition in the WWER fuel market for the operators of these reactors are : (1) lower cost; (2) more favorable contract terms and improved vendor cooperation with the customer; (3) accelerated technological development. A brief description of the main WWER fuel suppliers TVEL, ABB Atom, BNFL, EVF and Westinghouse, as well as the status of some new companies as CEZ and SEP is given. The principal differences between Western and WWER fuels are outlined. The advanced features offered by the Western vendors and Russian fuel supply organisations are discussed. 2 tabs., 1 fig.

Experimental study of the passive flooding system in the WWER-1000 reactor

International Nuclear Information System (INIS)

Malyshev, A.B.; Efanov, A.D.; Kalyakin, S.G.

2002-01-01

The design solution of the passive flooding system in the WWER-1000 reactor core with the V-392 reactor facility and the scheme of the GE-2 large-scale thermohydraulic stand for substantiation of its functions are presented. The proposals, improving the efficiency of the system are developed on the basis of the experimental studies on the equipment input-output operational characteristics and the recommendations on the substantiation of the function of the reactor core flooding system are given [ru

Advanced fuel cycles of WWER-1000 reactors

International Nuclear Information System (INIS)

Lunin, G.; Novikov, A.; Pavlov, V.; Pavlovichev, A.

2003-01-01

The present paper considers characteristics of fuel cycles for the WWER-1000 reactor satisfying the following conditions: duration of the campaign at the nominal power is extended from 250 EFPD up to 470 and more ones; fuel enrichment does not exceed 5 wt.%; fuel assemblies maximum burnup does not exceed 55 MWd/kgHM. Along with uranium fuel, the use of mixed Uranium-Plutonium fuel is considered. Calculations were conducted by codes TVS-M, BIPR-7A and PERMAK-A developed in the RRC Kurchatov Institute, verified for the calculations of uranium fuel and certified by GAN RF

Numerical effects in the neutron flux calculations into WWER-type reactor vessels by Monte Carlo method

International Nuclear Information System (INIS)

Alvarez Cardona, C.M.; Rodriguez Gual, M.; Hernandez Valle, S.

2001-01-01

The calculation of neutron fluxes and fluence into reactor pressure vessel is a regulatory requirement in the stages of the design, operation and plan lifetime extension. The reactor vessel is considered a unique and non-substitutable part of the NPP that undergoes degradation. The main source of the aging comes from the fast neutron damage induced in the steel crystalline lattice. Due to the proximity of the core edge to the vessel inner surface; the vessel steel is exposed to high fast neutron fluence. The effect of this irradiation on the mechanical properties becomes more acute because of the impurities measured in the Russian steel alloys. In the present paper, a PC version of the Monte Carlo 3-D HEXANN-EVALU system is used for the estimation of the WWER reactor pressure vessel irradiation. It was selected on the basis of its flexible options that on the other hand need to be quantified in connection with the desired magnitudes. The parameters that control the random walk of neutrons as well as the efficiency increasing options included in the code are studied in order to identify their impact in the final results for fluxes and fluence in the reactor pressure vessel. As a result an optimal set of parameters is suggested. (authors)

On steady-state concentrations of ammonia and molecular hydrogen in the primary circuit of the WWER-1000 reactors

International Nuclear Information System (INIS)

Arkhipov, O.P.; Bugaenko, V.L.; Kamakchi, S.A.

1997-01-01

It is shown that the MORAVA-N2 software package describes well the coolant state in the primary circuit of an actual reactor facility with the WWER-1000 during on-load operation. It permits using the package for analysis of process perturbation effect on the coolant composition. Specific feature of ammonia radiation chemistry in the primary circuit of a reactor facility with the WWER-1000, assuring the rates hydrogen concentration in the coolant with ammonia concentration variation in the coolant within wide limits, when reactor operates on power, can be mentioned by way of example, the fact being ascertained in this study

Assessment of the integrity of WWER type reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.

1995-01-01

Procedures are given for the assessment of the residual lifetime of reactor pressure vessels with respect to a sudden failure, the lifetime of vessels with defects disclosed during in-service inspections, and the fatigue or corrosion-mechanical lifetime. Also outlined are the ways of assessing the effects of major degradation mechanisms, i.e. radiation embrittlement, thermal aging, and fatigue damage, including the use of calculated values and experimental examination, by means of surveillance specimens in particular. All results of assessment performed so far indicate that the life of reactor pressure vessels at the Dukovany, Jaslovske Bohunice, and Temelin nuclear power plants is well secured. 7 figs., 3 refs

Surveillance extension experience at WWER-440 type reactors

International Nuclear Information System (INIS)

Gillemot, F.; Uri, G.; Oszwald, F.; Trampus, P.

1993-01-01

In WWER-440 reactors, the surveillance specimens are located in accelerated irradiation positions. After 5 years, all specimens are withdrawn and the operational changes are not monitored. At Paks NPP a new surveillance program extension has been settled in order to avoid these original program disadvantages and generate further data for plant lifetime management. This paper includes: research performed to prepare the surveillance extension programme, the evaluation method for the surveillance extension, and first results (Charpy and tensile tests). (authors). 6 refs., 12 figs., 3 tabs

Surveillance extension experience at WWER-440 type reactors

Energy Technology Data Exchange (ETDEWEB)

Gillemot, F; Uri, G [Budapesti Mueszaki Egyetem, Budapest (Hungary); Oszwald, F; Trampus, P

1994-12-31

In WWER-440 reactors, the surveillance specimens are located in accelerated irradiation positions. After 5 years, all specimens are withdrawn and the operational changes are not monitored. At Paks NPP a new surveillance program extension has been settled in order to avoid these original program disadvantages and generate further data for plant lifetime management. This paper includes: research performed to prepare the surveillance extension programme, the evaluation method for the surveillance extension, and first results (Charpy and tensile tests). (authors). 6 refs., 12 figs., 3 tabs.

The use of the codes from MCU family for calculations of WWER type reactors

International Nuclear Information System (INIS)

Abagijan, L.P.; Alexeyev, N.I.; Bryzgalov, V.I.; Gomin, E.A.; Glushkov, A.E.; Gorodkov, S.S.; Gurevich, M.I.; Kalugin, M.A.; Marin, S.V.; Shkarovsky, D.A.; Yudkevich, M.S.

2000-01-01

The MCU-RFFI/A and MCU-REA codes developed within the framework of the long term MCU project are widely used for calculations of neutron physic characteristics of WWER type reactors. Complete descriptions of the codes are available in both Russian and English. The codes are verified and validated by means of the comparison of calculated results with experimental data and mathematical benchmarks. The codes are licensed by Russian Nuclear and Criticality Safety Regulatory Body (Gosatomnadzor RF) (Code Passports: N 61 of 17.10.1966 and N 115 of 02.03.2000 accordingly)). The report gives examples of WWER reactor physic tasks important for practice solved using the codes from the MCU family. Some calculational results are given too. (Authors)

Modelling the WWER-type reactor dynamics using a hybrid computer. Part 1

International Nuclear Information System (INIS)

Karpeta, C.

Results of simulation studies into reactor and steam generator dynamics of a WWER type power plant are presented. Spatial kinetics of the reactor core is described by a nodal approximation to diffusion equations, xenon poisoning equations and heat transfer equations. The simulation of the reactor model dynamics was performed on a hybrid computer. Models of both a horizontal and a vertical steam generator were developed. The dynamics was investigated over a large range of power by computing the transients on a digital computer. (author)

Manufacture of rings of 08Kh18N10T sheet for internal structures of WWER type reactors

International Nuclear Information System (INIS)

Fojta, A.; Nitka, B.

1984-01-01

Technology is presented of the manufacture of rings for the jacket, shaft, core catcher and shaft bottom of WWER-440 reactors produced by Vitkovice Steel Works. The rings are manufactured from sheets of austenitic steel 08Kh18N10T. The materials and technology problems are discussed of sheet production, ring welding technology and annealing following welding. The plastic properties are assessed of the welded joints and problems are outlined of ring production for WWER-1000 reactors. (B.S.)

Safety of reactors built according to earlier standards (WWER 440/V230 type)

International Nuclear Information System (INIS)

Misak, J.; Rohar, S.

1995-01-01

The problems of safety of WWER-440/V-230 type reactors are discussed, and the following conclusions are made. (1) The reactors have a very good operational record. (2) The reactors have serious design shortcomings, which should be eliminated by safety upgrading. Core damage frequency should be further reduced. (3) PSA methods constitute an appropriate tool for assessment of plant vulnerability to some initiating events and malfunctions, for prioritization of upgrading measures and for tolerability of deviations from current safety standards. (4) The most important safety merits, such as a large thermal inertia and low rupture probability, should be properly taken into account in the analysis. (5) Extensive safety upgrading is feasible and can lead to a considerable risk reduction. In certain circumstances such upgrading is the least expensive option even though the total cost is much higher than the initial plant construction cost. (6) Properly upgraded, the reactor units may be operable until better power resources are available within the country. (7) The existing gap between the technological and political judgements of nuclear safety should be reduced continuously by information exchange improvements. (8) A unified approach to nuclear safety should be adopted for all nuclear reactors (not just WWERs) built to earlier standards. 5 tabs., 1 fig

Experience of developments and implementation of advanced fuel cycles of WWER-440 reactors

International Nuclear Information System (INIS)

Gagarinski, A.A.; Lizorkin, M.P.; Novikov, A.N.; Proselkov, V.N.; Saprykin, V.V.

2000-01-01

The paper presents the experience of development and implementation of advanced four- and five-year fuel cycles in the WWER-440 reactors, the results of experimental operation of the new fuel design and the main neutronic characteristics of the core. (Authors)

Advances in new WWER designs to improve operation and maintenance

International Nuclear Information System (INIS)

Dragunov, Y.G.; Ryzhov, S.B.; Podshibiakin, A.K.; Vasilchenko, I.N.; Repin, A.I.; Nikitenko, M.P.; Konoplev, N.P.; Fil, N.S.

2000-01-01

Economic operational indices of WWER-type reactors show their competitiveness in all the countries where these reactors operate. Advanced WWERs being designed and constructed now have the improved characteristics of economical efficiency and are more convenient for operation and maintenance. Many technical solutions aimed at improvement of the operational performance are implemented in the design of WWER-1000/V-392 and WWER-640/V-407, and these reactors are the important basis for the nuclear power expansion in Russia. Some of these solutions are considered in the present paper. (author)

Monitoring system for accuracy and reliability characteristics of standard temperature measurements in WWER-440 reactors

International Nuclear Information System (INIS)

Stanc, S.; Repa, M.

2001-01-01

Description of a monitoring system for accuracy and reliability characteristics of standard temperature measurements in WWER-440 reactors and benefits obtained from its use are shown in the presentation. As standard reactor temperature measurement, coolant temperature measurement at fuel assembly outlets and in loops, entered into the In-Reactor Control System , are considered. Such systems have been implemented at two V-230 reactors and are under implementation at other four V-213 reactors. (Authors)

Neutron irradiation effects in reactor pressure vessel steels and weldments. Working document

International Nuclear Information System (INIS)

1998-10-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. A separate abstract was prepared for the introduction and for each of the eleven chapters, which are: 1. Reactor Pressure Vessel Design, 2. Reactor Pressure Materials, 3. WWER Pressure Vessels, 4. Determination of Mechanical Properties, 5. Neutron Exposure, 6. Methodology of Irradiation Experiments, 7. Effect of Irradiation on Mechanical Properties, 8. Mechanisms of Irradiation Embrittlement, 9. Modelling of Irradiation Damage, 10. Annealing of Irradiation Damage, 11. Safety Assessment using Surveillance Programmes and Data Bases

Safety of light-water reactor pressure vessels against brittle fracture

International Nuclear Information System (INIS)

Brumovsky, M.

1979-01-01

The results are surveyed of research by SKODA Trust into brittle failure resistance of materials for WWER type reactor pressure vessels and into pressure vessel operating safety. Conditions are discussed in detail decisive for initiation, propagation and arrest of brittle fracture. The tests on the Cr-Mo-V type steel showed high resistance of the steel to the formation and the propagation of brittle fracture. They also confirmed the high operating reliability and the required service life of the steel. (B.S.)

The numerical simulation of the WWER-440/V-213 reactor pressure vessel internals response to maximum hypothetical large break loss of coolant accident

International Nuclear Information System (INIS)

Hermansky, P.; Krajcovic, M.

2012-01-01

The reactor internals are designed to ensure cooling of the fuel, to ensure the movement of emergency control assemblies under all operating conditions including accidents and facilitate removal of the fuel and of the internals following an accident This paper presents results of the numerical simulation of the WWER-440/V213 reactor vessel internals dynamic response to maximum hypothetical Large-Break Loss of Coolant Accident. The purpose of this analysis is to determine the reactor vessel internals response due to rapid depressurization and to prove no such deformations occur in the reactor vessel internals which would prevent timely and proper activation of the emergency control assemblies. (Authors)

The FARC fuel archive of WWER

International Nuclear Information System (INIS)

Zizin, M.N.; Parfenova, N.A.; Proselkov, V.N.; Shishkov, L.K.

1998-01-01

The principles of organisation are explained and the structure of the FARC fuel archive for WWER reactors is circumscribed. The objective of archive is accumulation of fuel data, data storage and obtaining of fuel using characteristics. The working version of fuel archive on 01 July 1998 is realised, in which the data tables for fuel assemblies for 169 WWER-440 cycles and 35 WWER-1000 cycles are stored. There are two different versions of fuel archive - for WWER-440 (FARC) and for WWER-1000 (FARC1000). A structure of some tables and the texts of programs for them differ. (Authors)

WWER-440 control assembly local power peaking investigation on LR-0 reactor

International Nuclear Information System (INIS)

Mikus, J.

2002-01-01

This paper presents information concerning the local power peaking problem induced by the WWER-440 control assembly and the investigation possibilities on the light water, zero power reactor LR-0 at the Nuclear Research Institute (NRI) Rez plc. A brief description is given about the disposable control assembly model, experimental arrangement and conditions on the LR-0 reactor with regard to the earlier performed investigations as well as to the relevant measurements to be realized in the near future.(abstract)

New paradigm for prediction of radiation life-time of reactor pressure vessel

International Nuclear Information System (INIS)

Kotrechko, S.A.; Meshkov, Yu.Ya.; Neklyudov, I.M.; Revka, V.N.

2011-01-01

New paradigm for prediction of radiation life-time of reactor pressure vessel is presented. Equation for limiting state of reactor pressure vessel wall with crack-like defect is obtained. It is exhibited that the value of critical fluence Φ c may be determined not by shift of critical temperature of fracture of surveillance specimen, which is indirect characteristic, but by direct method, namely, by the condition of initiation of brittle fracture of irradiated metal ahead of a crack in RPV wall. Within the framework of engineering version of LA to fracture the technique for Φ c ascertainment is developed. Prediction of Φ c for WWER pressure vessels demonstrates potentialities of this technique.

Control assembly ejection accident analysis for WWER-440 (Armenian NPP)

International Nuclear Information System (INIS)

Bznuni, S.; Malakyan, Ts.; Amirjanyan, A.; Ghasabyan, L.

2007-01-01

Control Assembly ejection in WWER-440 initiated by the loss of integrity of the Control Assemblies drive housing has been analyzed. This event causes a very rapid reactivity insertion to the core and small break LOCA which potentially could lead to rapid power increase and redistribution of heat release in the core resulting in a fuel, cladding and coolant temperature rise; primary pressure increase, radiological consequences due to loss of primary coolant and potential loss of cladding integrity and fuel disintegration (if applicable). Methodology of the analysis is based on conservative assumptions as well as on deterministic approach for selection of functioning logic of systems and equipment's to maximize reactor core power and minimize power decreasing reactivity feedback. Computational analyses were performed by 3D kinetics PARCS-RELAP coupled code. WWER-440 fuel cross-section libraries, diffusion coefficients and kinetics parameters were calculated by HELOS code. In this paper analysis of accident for Hot Full Power was presented. Results of analysis show that ANPP WWER-440 reactor design meets acceptance criteria prescribed for RIA type design based accidents (Authors)

Analysis of WWER-440 and PWR RPV welds surveillance data to compare irradiation damage evolution

Energy Technology Data Exchange (ETDEWEB)

Debarberis, L. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands)]. E-mail: luigi.debarberis@cec.eu.int; Acosta, B. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands)]. E-mail: beatriz.acosta-iborra@jrc.nl; Zeman, A. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands); Sevini, F. [Joint Research Centre of the European Commission, Institute for Energy, P.O. Box 2, 1755 ZG Petten (Netherlands); Ballesteros, A. [Tecnatom, Avd. Montes de Oca 1, San Sebasitan de los Reyes, E-28709 Madrid (Spain); Kryukov, A. [Russian Research Centre Kurchatov Institute, Kurchatov Square 1, 123182 Moscow (Russian Federation); Gillemot, F. [AEKI Atomic Research Institute, Konkoly Thege M. ut 29-33, 1121 Budapest (Hungary); Brumovsky, M. [NRI, Nuclear Research Institute, Husinec-Rez 130, 25068 Rez (Czech Republic)

2006-04-15

It is known that for Russian-type and Western water reactor pressure vessel steels there is a similar degradation in mechanical properties during equivalent neutron irradiation. Available surveillance results from WWER and PWR vessels are used in this article to compare irradiation damage evolution for the different reactor pressure vessel welds. The analysis is done through the semi-mechanistic model for radiation embrittlement developed by JRC-IE. Consistency analysis with BWR vessel materials and model alloys has also been performed within this study. Globally the two families of studied materials follow similar trends regarding the evolution of irradiation damage. Moreover in the high fluence range typical of operation of WWER the radiation stability of these vessels is greater than the foreseen one for PWR.

Kozloduy NPP WWER-440/230 reactor pressure vessel radiation lifetime

Energy Technology Data Exchange (ETDEWEB)

Vodenicharov, S [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. po Metaloznanie i Tekhnologiya na Metalite; Kamenova, Tz [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. po Metaloznanie i Tekhnologiya na Metalite; Tzokov, P; Videnov, A [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Pekov, B [Committee on the Use of Atomic Energy for Peaceful Purposes, Sofia (Bulgaria)

1996-12-31

The processes of metal embrittlement induced by neutron irradiation embrittlement (NIE) and neutron re-irradiation embrittlement (NRE) of the rector pressure vessel (RPV) are investigated. Radiation lifetime is calculated using two approaches for re-embrittlement: a conservative law and a lateral shift of the critical transition temperature curve after neutron irradiation. In order to prevent NIE the following measures have been taken at the Kozloduy NPP: loading of dummy elements into core periphery; heating the water for emergency core cooling to 55{sup o} C; fast acting valves in the main steam piping, etc. The critical embrittlement temperature, the residual part of temperature shift and the radiation lifetime have been calculated for units 1 - 4 using the two approaches and updated information on P and Cu impurities content. It is concluded that if the lateral re-embrittlement law is adopted and the P content does not exceed 0.05%, all RPV should reach their design lifetime. The NIE in WWER-440/230 is related to C and P content in the weld 4 and is negligible for the Unit 4 in particular, which has low impurities content. In order to reach the design lifetime of the Units 1 - 3 it is necessary to install MSIV. A verification of chemical composition of the Unit 1 RPV weld 4 metal is recommended. 7 refs., 3 figs., 6 tabs.

Kozloduy NPP WWER-440/230 reactor pressure vessel radiation lifetime

International Nuclear Information System (INIS)

Vodenicharov, S.; Pekov, B.

1995-01-01

The processes of metal embrittlement induced by neutron irradiation embrittlement (NIE) and neutron re-irradiation embrittlement (NRE) of the rector pressure vessel (RPV) are investigated. Radiation lifetime is calculated using two approaches for re-embrittlement: a conservative law and a lateral shift of the critical transition temperature curve after neutron irradiation. In order to prevent NIE the following measures have been taken at the Kozloduy NPP: loading of dummy elements into core periphery; heating the water for emergency core cooling to 55 o C; fast acting valves in the main steam piping, etc. The critical embrittlement temperature, the residual part of temperature shift and the radiation lifetime have been calculated for units 1 - 4 using the two approaches and updated information on P and Cu impurities content. It is concluded that if the lateral re-embrittlement law is adopted and the P content does not exceed 0.05%, all RPV should reach their design lifetime. The NIE in WWER-440/230 is related to C and P content in the weld 4 and is negligible for the Unit 4 in particular, which has low impurities content. In order to reach the design lifetime of the Units 1 - 3 it is necessary to install MSIV. A verification of chemical composition of the Unit 1 RPV weld 4 metal is recommended. 7 refs., 3 figs., 6 tabs

In-service ultrasonic inspection of nuclear reactor pressure vessels

International Nuclear Information System (INIS)

Prepechal, J.; Sulc, J.

1982-01-01

Ultrasonic tests of pressure vessels for WWER 440 reactors, type 213 V, are carried out partly manually and partly by test equipment. The inner surface of the pressure vessel is tested using device REACTORTEST TRC which is fully mobile. The outer surface of the cylindrical parts and bottoms of the body is tested using handling equipment permanently in-built under the pressure vessel and dismountable testing heads. A set of these heads may be used for two reactor units. The testing equipment REACTORTEST TRC is equipped with a TRC 800 ultrasound device. The equipment for testing the outer surface of the vessel operates with the UDAR 16 ultrasound apparatus to which may be simultaneously connected 10 ultrasound probes and six probes for acoustic feedback. The whole system of ultrasonic tests makes possible a first-rate and reliable volume control of the whole pressure vessel and all points where cracks may originate and grow. (Z.M.)

East/west steels for reactor pressure vessels

International Nuclear Information System (INIS)

Davies, M.; Kryukov, A.; Nikolaev, Y.; English, C.

1997-01-01

The report consist of three parts dealing with comparison of the irradiation behaviour of 'Eastern' and 'Western' steels, mechanisms of irradiation embrittlement and the role of compositional variations on the irradiation sensitivity of pressure vessels. Nickel, copper and phosphorus are the elements rendering the most essential influence on behaviour of pressure vessel steels under irradiation and subsequent thermal annealing. For WWER-440 reactor pressure vessel (RPV) steels in which nickel content does nor exceed 0.3% the main affecting factors are phosphorous and copper. For WWER-1000 RPV welds in which nickel content generally exceed 1.5% the role of nickel in radiation embrittlement is decisive. In 'Western' type steels main influencing elements are nickel and copper. The secondary role of phosphorus in radiation embrittlement of 'Western' steels is caused by lower relative content compared to 'Eastern' steels. The process of how copper, phosphorus and nickel contents affect the irradiation sensitivity of both types of steel seem to be similar. Some distinctions between the observed radiation effects is apparently caused by differences in the irradiation conditions and ratios of the contents of above mentioned elements in both types of steel. For 'Eastern' RPV steels the dependence of the recovery degree of irradiated steels due to postirradiation thermal annealing id obviously dependent on phosphorus contents and the influence of nickel contents on this process is detectable

Main examination results of WWER-1000 fuel after its irradiation in power reactors

Energy Technology Data Exchange (ETDEWEB)

Bibiliashvili, Yu [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation); Dubrovin, K [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation); Vasilchenko, I [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation); Yenin, A; Kushmanov, A [AO Novosibirskij Zavod Khimcontsentratov, Novosibirsk (Russian Federation); Smirnov, A; Smirnov, V [Nauchno-Issledovatel` skij Inst. Atomnykh Reaktorov, Dimitrovgrad (Russian Federation)

1994-12-31

WWER-1000 fuel examination has been undertaken to specify the properties of fuel assembly members by defining the parameters of their materials and their interconnection in power reactor operation conditions. Nine fuel assemblies are examined. The examination program includes: visual inspection, measurement of overall dimensions, eddy-current test, gamma-scanning, X-ray and neutron radiography, analysis of gas pressure and composition inside fuel rods, ceramography/metallography, mass spectrometry, microanalysis and electron microscopy of fuel and fuel claddings. The examination results suggest that WWER-1000 fuel spent at steady-state operation conditions up to 50 Mwd/kg U of burnup is in satisfactory condition. The examination of all types of fuel cladding failures indicates that the reason lies in the interaction of cladding with coolant solid impurities. The nodular cladding corrosion of fuel assembly discharged from the South-Ukrainian NPP is caused by the graphite compounds deposited on the fuel rod. Those deposits are a result of the circulating pump damage and had accidental, non-typical character. Some of the rods were found to have a small cladding `fretting` of the spacer grid cell material. The values of the majority of parameters determining the fuel efficiency allow to assume that there is a potential for further extension of fuel burnup and operation length. 1 tab., 11 figs.

Main examination results of WWER-1000 fuel after its irradiation in power reactors

International Nuclear Information System (INIS)

Bibiliashvili, Yu.; Dubrovin, K.; Vasilchenko, I.; Yenin, A.; Kushmanov, A.; Smirnov, A.; Smirnov, V.

1994-01-01

WWER-1000 fuel examination has been undertaken to specify the properties of fuel assembly members by defining the parameters of their materials and their interconnection in power reactor operation conditions. Nine fuel assemblies are examined. The examination program includes: visual inspection, measurement of overall dimensions, eddy-current test, gamma-scanning, X-ray and neutron radiography, analysis of gas pressure and composition inside fuel rods, ceramography/metallography, mass spectrometry, microanalysis and electron microscopy of fuel and fuel claddings. The examination results suggest that WWER-1000 fuel spent at steady-state operation conditions up to 50 Mwd/kg U of burnup is in satisfactory condition. The examination of all types of fuel cladding failures indicates that the reason lies in the interaction of cladding with coolant solid impurities. The nodular cladding corrosion of fuel assembly discharged from the South-Ukrainian NPP is caused by the graphite compounds deposited on the fuel rod. Those deposits are a result of the circulating pump damage and had accidental, non-typical character. Some of the rods were found to have a small cladding 'fretting' of the spacer grid cell material. The values of the majority of parameters determining the fuel efficiency allow to assume that there is a potential for further extension of fuel burnup and operation length. 1 tab., 11 figs

Study on severe accidents and countermeasures for WWER-1000 reactors using the integral code ASTEC

International Nuclear Information System (INIS)

Tusheva, P.; Schaefer, F.; Altstadt, E.; Kliem, S.; Reinke, N.

2011-01-01

The research field focussing on the investigations and the analyses of severe accidents is an important part of the nuclear safety. To maintain the safety barriers as long as possible and to retain the radioactivity within the airtight premises or the containment, to avoid or mitigate the consequences of such events and to assess the risk, thorough studies are needed. On the one side, it is the aim of the severe accident research to understand the complex phenomena during the in- and ex-vessel phase, involving reactor-physics, thermal-hydraulics, physicochemical and mechanical processes. On the other side the investigations strive for effective severe accident management measures. This paper is focused on the possibilities for accident management measures in case of severe accidents. The reactor pressure vessel is the last barrier to keep the molten materials inside the reactor, and thus to prevent higher loads to the containment. To assess the behaviour of a nuclear power plant during transient or accident conditions, computer codes are widely used, which have to be validated against experiments or benchmarked against other codes. The analyses performed with the integral code ASTEC cover two accident sequences which could lead to a severe accident: a small break loss of coolant accident and a station blackout. The results have shown that in case of unavailability of major active safety systems the reactor pressure vessel would ultimately fail. The discussed issues concern the main phenomena during the early and late in-vessel phase of the accident, the time to core heat-up, the hydrogen production, the mass of corium in the reactor pressure vessel lower plenum and the failure of the reactor pressure vessel. Additionally, possible operator's actions and countermeasures in the preventive or mitigative domain are addressed. The presented investigations contribute to the validation of the European integral severe accidents code ASTEC for WWER-1000 type of reactors

Thermophysical aspects of WWER safety

International Nuclear Information System (INIS)

Kolochko, Vladimir N.

1999-01-01

The paper presents a review of the main thermophysical aspects of NPPs safety and efficiency increase applied to WWERs. Improvement of operating WWER units is the main short-term and medium-term tasks of the utilities in Ukraine. The new generation of reactors for increasing the reactor facilities efficiency should utilize achievements of thermo physics research results. The thermophysical aspects of NPPs safety and efficiency are envisaged in the context of the atomic energy development strategy. The analysis of thermophysical processes occurring in the core shows that a number of problems concerning boiling crisis and heat exchange intensification during transient and accidents are not solved in spite of numerous calculations and experimental research. The up-to-date safety conception includes severe accidents consideration for safety assessment. Review of severe accidents management is presented. Additional validation of the West advanced thermal hydraulic codes which are applied for WWERs reassessment calculations is required. Contribution of the processes which might occur in WWER containment to safety problems solving is considered as well. (author)

Application of the LBB regulatory approach to the steamlines of advanced WWER 1000 reactor

Energy Technology Data Exchange (ETDEWEB)

Kiselyov, V.A.; Sokov, L.M.

1997-04-01

The LBB regulatory approach adopted in Russia in 1993 as an extra safety barrier is described for advanced WWER 1000 reactor steamline. The application of LBB concept requires the following additional protections. First, the steamline should be a highly qualified piping, performed in accordance with the applicable regulations and guidelines, carefully screened to verify that it is not subjected to any disqualifying failure mechanism. Second, a deterministic fracture mechanics analysis and leak rate evaluation have been performed to demonstrate that postulated through-wall crack that yields 95 1/min at normal operation conditions is stable even under seismic loads. Finally, it has been verified that the leak detection systems are sufficiently reliable, diverse and sensitive, and that adequate margins exist to detect a through wall crack smaller than the critical size. The obtained results are encouraging and show the possibility of the application of the LBB case to the steamline of advanced WWER 1000 reactor.

Application of the LBB regulatory approach to the steamlines of advanced WWER 1000 reactor

International Nuclear Information System (INIS)

Kiselyov, V.A.; Sokov, L.M.

1997-01-01

The LBB regulatory approach adopted in Russia in 1993 as an extra safety barrier is described for advanced WWER 1000 reactor steamline. The application of LBB concept requires the following additional protections. First, the steamline should be a highly qualified piping, performed in accordance with the applicable regulations and guidelines, carefully screened to verify that it is not subjected to any disqualifying failure mechanism. Second, a deterministic fracture mechanics analysis and leak rate evaluation have been performed to demonstrate that postulated through-wall crack that yields 95 1/min at normal operation conditions is stable even under seismic loads. Finally, it has been verified that the leak detection systems are sufficiently reliable, diverse and sensitive, and that adequate margins exist to detect a through wall crack smaller than the critical size. The obtained results are encouraging and show the possibility of the application of the LBB case to the steamline of advanced WWER 1000 reactor

Stresses in reactor pressure vessel nozzles -- Calculations and experiments

International Nuclear Information System (INIS)

Brumovsky, M.; Polachova, H.

1995-01-01

Reactor pressure vessel nozzles are characterized by a high stress concentration which is critical in their low-cycle fatigue assessment. Program of experimental verification of stress/strain field distribution during elastic-plastic loading of a reactor pressure vessel WWER-1000 primary nozzle model in scale 1:3 is presented. While primary nozzle has an ID equal to 850 mm, the model nozzle has ID equal to 280 mm, and was made from 15Kh2NMFA type of steel. Calculation using analytical methods was performed. Comparison of results using different analytical methods -- Neuber's, Hardrath-Ohman's as well as equivalent energy ones, used in different reactor Codes -- is shown. Experimental verification was carried out on model nozzles loaded statically as well as by repeated loading, both in elastic-plastic region. Strain fields were measured using high-strain gauges, which were located in different distances from center of nozzle radius, thus different stress concentration values were reached. Comparison of calculated and experimental data are shown and compared

Measuring neutron flux density in near-vessel space of a commercial WWER-1000 reactor

International Nuclear Information System (INIS)

Borodkin, G.I.; Eremin, A.N.; Lomakin, S.S.; Morozov, A.G.

1987-01-01

Distribution of neutron flux density in two experimental channels on the reactor vessel external surface and in ionization chamber channel of a commercial WWER-1000 reactor, is measured by the activation detector technique. Azimuthal distributions of fast and thermal neutron fluxes and height distributions of fast neutron flux density within energy range >1.2 and 2.3 MeV are obtained. Conclusion is made, that reactor core state and its structural peculiarities in the measurement range essentially affect space and energy distribution of neutron field near the vessel. It should be taken into account when determining permissible neutron fluence for the reactor vessel

Nuclear fuel for WWER reactors. Current status and prospects

International Nuclear Information System (INIS)

Molchanov, V.

2006-01-01

In this paper the following results from the JSC TVEL post-irradiation studies of full-scale fuel assemblies are discussed: 1) Oxide layer on fuel rod (FR) cladding does not exceed 15 μm; 2) Fission Gas Release does not exceed 3%; 3) Satisfactory condition of cladding. Concerning the operating experience it is noticed that: 1) Design criteria are fulfilled; 2) 5 TVSA are stayed at Kalinin-1 for 6 years up to burnup of 59 MWxdays/kgU; 3) 12 working assemblies (WA) are operated at Kola-3 for 6 years up to burnup of 57 MWxdays/kgU. At the end the following conclusions are made: 1) The main task of further development of nuclear fuel for WWER-1000 reactors is the increasing fuel rod burnup up to 72 MWxdays/kgU and operating life up to 6 years through the increase in uranium load in FA and maximum use of potential built-in in the designs of TVSA and TVS-2; 2) In the nearest future R and D in the field of nuclear fuel for WWER will be directed at justification of maneuvering fuel characteristics as well as at introducing of optimized zirconium alloys

Two-dimensional full-core transport theory Benchmarks for the WWER reactors

International Nuclear Information System (INIS)

Petkov, P.T.

2002-01-01

Several two-dimensional full-core real geometry many-group steady-state problems for the WWER-440 and WWER-1000 reactors have been solved by the MARIKO code, based on the method of characteristics. The reference transport theory solutions include assembly-wise and pin-wise power distributions. Homogenized two-group diffusion parameters and discontinuity factors have been calculated by MARIKO for each assembly type both for the whole assembly and for each cell in the smallest sector of symmetry, using the B1 method for calculation of the critical spectrum. Accurate albedo-type boundary conditions have been calculated by MARIKO for the core-reflector and core-absorber boundaries, both for each outer assembly face and for each outer cell face. Comparison with the reference solutions of the two-group nodal diffusion code SPPS-1.6 and the few-group fine-mesh diffusion codes HEX2DA and HEX2DB are presented (Authors)

Radiation embrittlement of WWER-1000 reactor vessel steels

International Nuclear Information System (INIS)

Nikolaeva, A.V.; Nikolaev, Yu.A.; Kevorkyan, Yu.R.

2001-01-01

Results obtained on the blank samples of materials of the WWER-1000 vessels irradiated by low density neutron flux are discussed. Chemical composition of the materials is characterized by the low content of the impurities (copper and phosphorus) and high content of nickel. Dependence of the radiation embrittlement of the WWER-1000 vessel materials on metallurgic variables and damage dose is treated. The research showed that nickel largely enhanced the radiation embrittlement. New dependences for determination of the radiation embrittlement real rate of the WWER-1000 vessel materials and its conservative estimation were developed [ru

The IAEA extrabudgetary programme on the safety of WWER and RBMK plants

International Nuclear Information System (INIS)

Havel, R.

1995-01-01

Data on WWER-440/213, WWER-440/230, WWER-1000 and RBMK reactors in operation are presented. Organizational chart for the IAEA extrabudgetary programme on the safety of WWER and RBMK plants, general programme objectives and main components are outlined

Code Package to Analyze Parameters of the WWER Fuel Rod. TOPRA-2 Code - Verification Data

International Nuclear Information System (INIS)

Scheglov, A.; Proselkov, V.; Passage, G.; Stefanova, S.

2009-01-01

Presented are the data for computer codes to analyze WWER fuel rods, used in the WWER department of RRC 'Kurchatov Institute'. Presented is the description of TOPRA-2 code intended for the engineering analysis of thermophysical and strength parameters of the WWER fuel rod - temperature distributions along the fuel radius, gas pressures under the cladding, stresses in the cladding, etc. for the reactor operation in normal conditions. Presented are some results of the code verification against test problems and the data obtained in the experimental programs. Presented are comparison results of the calculations with TOPRA-2 and TRANSURANUS (V1M1J06) codes. Results obtained in the course of verification demonstrate possibility of application of the methodology and TOPRA-2 code for the engineering analysis of the WWER fuel rods

Evaluation of WWER-1000 vessel materials fracture toughness

International Nuclear Information System (INIS)

Grinik, Eh.U.; Revka, V.N.; Chirko, L.I.; Chajkovskij, Yu.V.

2007-01-01

The lifetime of WWER-1000-type reactor vessels is finally conditioned by the fracture toughness (crack growth resistance) of RPV materials. Up to now in line with the regulations the fracture toughness is characterized by the critical temperature of brittleness determined by the results of the Charpy specimen impact testing. Such approach is typical for all countries operating the water pressure reactors. However, regulatory approach is known from the western specialists not always to characterize adequately the crack growth resistance of the vessel materials and in some cases to underestimate their characteristics in the reference state that leads to unreasonably high conservatism. Excessive conservatism may lead to the invalid restrictions in the operating modes and the service life of the reactor vessel. Therefore there appeared the necessity to apply another approaches based on the state-of-the-art experimental methods of the fracture mechanics and allowing evaluating the fracture toughness parameters sufficiently. The paper presents the results of the comparison of the regulatory approach and the Master curve approach from the point of view of the adequate determination of the vessel material crack growth resistance parameters. Analysis of the experimental data of the surveillance specimens illustrated the potential possibility of applying the new statistical method for the WWER-1000- type reactor vessel lifetime extension

Automatic accounting of nuclear materials at WWER type reactor NPPs

International Nuclear Information System (INIS)

Babaev, N.S.; Poznyakov, N.L.; Strelkov, D.F.

1978-01-01

The possibilities of automatic accounting of nuclear materials at NPPs based on WWER reactors are considered. Organizational and technical principles of an automated system of accounting that takes into consideration IAEA requirements in conducting accounting documentation are proposed. A program is described for accounting materials using a BESM-6 computer. Operation of the program requires that all accounting data be recorded on conventional carriers of computer information (magnetic tapes, discs, perforated cards), which constitute the basic NPP accounting documents and may be directly used as initial data for a corresponding information program

Topic 1. Steels for light water reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Brynda, J.; Kepka, M.; Barackova, L.; Vacek, M.; Havel, S.; Cukr, B.; Protiva, K.; Petrman, I.; Tvrdy, M.; Hyspecka, L.; Mazanec, K.; Kupca, L.; Brezina, M.

1980-01-01

Part 1 of the Proceedings consists of papers on the criteria for the selection and comparison of the properties of steel for pressure vessels and on the metallurgy of the said steels, the selection of suitable material for internal tubing systems, the manufacture of high-alloy steels for WWER components, the mechanical and metallurgical properties of steel 22K for WWER 440 pressure components, and of steel 10MnNi2Mo for the WWER primary coolant circuit, and the metallographic assessment of steel 0Kh18N10T. (J.P.)

Approaches for accounting and prediction of fast neutron fluence on WWER pressure vessels and results of validation of calculational procedure

International Nuclear Information System (INIS)

Borodkin, P.G.; Khrennikov, N.N.; Ryabinin, Yu.A.; Adeev, V.A.

2015-01-01

A description is given of the universal procedure for calculation of fast neutron fluence (FNF) on WWER vessels. Approbation of the calculation procedure was carried out by comparing the calculation results for this procedure and measurements on the outer surface of the WWER-440 and WWER-1000 vessels. In addition, an estimation of the uncertainty of the settlement procedure was made in accordance with the requirements of regulatory documents. The developed procedure is applied at Kola NPP for independent fast neutron fluence estimates on the WWER-440 reactor vessels when planning core loads taking into account the introduction of new fuels. The results of the pilot operation of the procedure for calculating FNF at the Kola NPP were taken into account when improving the procedure and its application to the calculations of FNF on the WWER-1000 vessels [ru

Results of neutron physics analyses of WWER-440 cores with modified reactor protection and control systems

International Nuclear Information System (INIS)

Lehmann, M.; Pecka, M.; Rocek, J.; Zalesky, K.

1993-12-01

Detailed results are given of neutron physics analyses performed to assess the efficiency and acceptability of modifications of the WWER-440 core protection and control system; the modifications have been proposed with a view to increasing the proportion of mechanical control in the compensation of reactivity effects during reactor unit operation in the variable load mode. The calculations were carried out using the modular MOBY-DICK macrocode system together with the SMV42G36 library of two-group parametrized diffusion constants, containing corrections which allow new-design WWER-440 fuel assemblies to be discriminated. (J.B). 37 tabs., 18 figs., 5 refs

Effects of nickel on irradiation embrittlement of light water reactor pressure vessel steels

International Nuclear Information System (INIS)

2005-06-01

This TECDOC was developed under the IAEA Coordinated Research Project (CRP) entitled Effects of Nickel on Irradiation Embrittlement of Light Water Reactor Pressure Vessel (RPV) Steels. This CRP is the sixth in a series of CRPs to determine the influence of the mechanism and quantify the influence of nickel content on the deterioration of irradiation embrittlement of reactor pressure vessel steels of the Ni-Cr-Mo-V or Mn-Ni-Cr-Mo types. The scientific scope of the programme includes procurement of materials, determination of mechanical properties, irradiation and testing of specimens in power and/or test reactors, and microstructural characterization. Eleven institutes from eight different countries and the European Union participated in this CRP and six institutes conducted the irradiation experiments of the CRP materials. In addition to the irradiation and testing of those materials, irradiation experiments of various national steels were also conducted. Moreover, some institutes performed microstructural investigations of both the CRP materials and national steels. This TECDOC presents and discusses all the results obtained and the analyses performed under the CRP. The results analysed are clear in showing the significantly higher radiation sensitivity of high nickel weld metal (1.7 wt%) compared with the lower nickel base metal (1.2 wt%). These results are supported by other similar results in the literature for both WWER-1000 RPV materials, pressurized water reactor (PWR) type materials, and model alloys. Regardless of the increased sensitivity of WWER-1000 high nickel weld metal (1.7 wt%), the transition temperature shift for the WWER-1000 RPV design fluence is still below the curve predicted by the Russian code (standard for strength calculations of components and piping in NPPs - PNAE G 7-002-86). For higher fluence, no data were available and the results should not be extrapolated. Although manganese content was not incorporated directly in this CRP

Code systems for effective and precise calculation of the basic neutron characteristics, core loading optimization, analysis and estimation of the operation regimes of WWER type reactors

International Nuclear Information System (INIS)

Apostolov, T.; Ivanov, K.; Prodanova, R.; Manolova, M.; Petrova, T.; Alekova, G.

1993-01-01

Two directions for investigations are suggested: 1) Analysis and evaluation of the real loading patterns and operational regimes for Kozloduy NPP WWER-440 and WWER-1000 in the frame of the recent safety criteria and nuclear power plant operating limits. 2) Development of modern code system for WWER type reactor core analysis with advanced features: new design and materials for fuel and control rods, increasing the fuel enrichment, using the integral and discrete burnable absorbers etc. The fuel technology design evolution maximizes the fuel utilization efficiency, improves operation performance and enhances safety margins. By the joint efforts of specialists from INRNE, Sofia (BG) and KAB, Berlin (GE), the codes NESSEL-IV-EC, PYTHIA and DERAB have been developed and verified. In the frame of the PHARE programme the joint project ASPERCA has been proposed intended for reactor physics calculations with PHYBER-WWER code for safety enhancement and operation reliability improvement. In-core fuel management benchmarks for 4 cycles of unit 2 (WWER-440) and 2 cycles of unit 5 (WWER-1000) have been performed. The coordination of burnable absorber design implementation, low leakage loadings usage, reloading enrichment increase and steel content reduction in the core have made the reactor core analysis more demanding and the definition of loading patterns - more difficult. This complexity requires routine use of three-dimensional fast accurate core model with extended and updated cross section libraries. To meet the needs of WWER advanced loading patterns and in-core fuel management improvements the HEXANES code systems is being developed and qualified. Some test calculations have been carried out by the HEXANES code system investigating the influence of Gd in the fuel on the main reactor physics parameters. For reevaluation of the core safety-related design limits forming the basis of licensing procedure, the code DYN3D/M2 is used. 16 refs., 3 figs. (author)

WWER type reactors used as multipurpose nuclear power sources

International Nuclear Information System (INIS)

Fiala, J.; Mulak, J.

1976-01-01

Safety aspects are assessed of the siting of nuclear power installations in the vicinity of large housing estates and in areas with a high population density, mainly the aspect of the liquidation of the consequences of the maximum credible accident, i.e., the transversal rupture of the primary coolant circuit. The application of WWER type reactors as multipurpose nuclear power sources in Czechoslovakia is justified. It is shown that such a multipurpose nuclear power source differs from a purely condensation nuclear power plant mainly in the design of the secondary stage. The possibilities of such projects are indicated with a view to power and heat operation. (F.M.)

Failed fuel diagnosis during WWER reactor operation using the RTOP-CA code

International Nuclear Information System (INIS)

Likhanskii, V.; Afanasieva, E.; Sorokin, A.; Evdokimov, I.; Kanukova, V.; Khromov, A.

2006-01-01

The mechanistic code RTOP-CA is developed for objectives of failed fuel diagnosis during WWER reactor operation. The RTOP-CA code enables to solve a direct problem: modelling the failed fuel behavior and prediction of primary coolant activity if characteristics of failures in the reactor core are known. Results of verification of the RTOP-CA code are presented. Separate physical models were verified on small-scale in-pile and out-of-pile experiments. Integral verification cases included data obtained at research reactors and at nuclear power plants. The RTOP-CA code is used for development of a neural-network approach to the inverse problem: detection of failure characteristics on the base of data on primary coolant activity during reactor operation. Preliminary results of application of the neural-network approach for evaluation of fuel failure characteristics are presented. (authors)

Vibrodynamical tests of RP equipment with application of imitation area of WWER-1000 reactor

International Nuclear Information System (INIS)

Khajretdinov, V.U.; Tarkhanov, V.V.; Rodionova, I.N.

2015-01-01

Performance of preoperational tests and measurements with application of imitation area of the reactor is a distinctive characteristic of putting into operation of NPP Units with WWER-1000/1200. The imitation area consists of 163 full-scale FA models, where fuel matrixes made of nuclear-fissionable material, are replaced by leaden simulators. Vibrodynamic tests involve inspection of hydrodynamic disturbances in the primary circuit (dynamic impact on the inspected elements), characteristics of vibration response of the main equipment stress-deformed state of bearing structure, and also parameters of moving and geometry of the inspected objects (boundary conditions at process simulation). Preoperational tests and measurements on the simulated area of WWER-1000/1200 are obligatory and performed at every unit of NPP of this type [ru

Safety assessment of unit 5 (WWER-440/W-213) of the Greifswald nuclear power station

International Nuclear Information System (INIS)

1992-02-01

The report represents the common results of the program of German-Soviet cooperation in reactor safety and radiation protection. The technical plant and features of type WWER-440/W-213 nuclear power plants, basic legal licensing principles, reactor core and pressurized components, load resulting from accidents, systems engineering, spreading impacts, civil engineering aspects, and the evaluation of operating experience are described. (DG)

Draft report of a consultants meeting on core control and protection strategy of WWER-1000 reactors. Extrabudgetary programme on the safety of WWER-1000 NPPs

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-07

At the consultants' meeting on the 'Safety of WWER-1000 Model 320 Nuclear Power Plants' organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of core control and protection strategy was identified as an issue of safety concern. Considering the safety importance of this issue, a consultants' meeting on 'Core Control and Protection Strategy for WWER-1000 Reactors' was convened in Vienna in April 1994 attended by 20 international experts in the area of core control and protection in order to review control and protection system design, to compare them with western practices and to recommend corrective measures. The first WWER-1000 NPP was put into operation in 1980 and there are currently 19 units operating. The accumulated operational experience is more than 130 reactor-years. In addition, there are 8 units under various stages of construction. The previous general observations in the area of core control and protection strategy was focused on core design objectives, core design and fuel management, fuel assembly and core component designs, including burnable absorber and control rod designs, core power distribution control strategy, core control and protection system designs and in-core and ex-core instrumentation systems. While core design objectives of WWER-1000 plants are similar to western practices in general, there are important differences on the design limits and regulatory practices followed for the compliance with the design limits. As a result of previous general observations and specific concerns on core control and protection system design, three working groups were formed to further investigate the specific issues and to compile information on safety issues based on design differences between these plants and similar western plants, to identify areas which need further analysis and make recommendations for short-term and long-term corrective

Draft report of a consultants meeting on core control and protection strategy of WWER-1000 reactors. Extrabudgetary programme on the safety of WWER-1000 NPPs

International Nuclear Information System (INIS)

1994-01-01

At the consultants' meeting on the 'Safety of WWER-1000 Model 320 Nuclear Power Plants' organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of core control and protection strategy was identified as an issue of safety concern. Considering the safety importance of this issue, a consultants' meeting on 'Core Control and Protection Strategy for WWER-1000 Reactors' was convened in Vienna in April 1994 attended by 20 international experts in the area of core control and protection in order to review control and protection system design, to compare them with western practices and to recommend corrective measures. The first WWER-1000 NPP was put into operation in 1980 and there are currently 19 units operating. The accumulated operational experience is more than 130 reactor-years. In addition, there are 8 units under various stages of construction. The previous general observations in the area of core control and protection strategy was focused on core design objectives, core design and fuel management, fuel assembly and core component designs, including burnable absorber and control rod designs, core power distribution control strategy, core control and protection system designs and in-core and ex-core instrumentation systems. While core design objectives of WWER-1000 plants are similar to western practices in general, there are important differences on the design limits and regulatory practices followed for the compliance with the design limits. As a result of previous general observations and specific concerns on core control and protection system design, three working groups were formed to further investigate the specific issues and to compile information on safety issues based on design differences between these plants and similar western plants, to identify areas which need further analysis and make recommendations for short-term and long-term corrective

State of the art of computer codes and experimental investigations on safety of nuclear power plants with reactors of WWER type

International Nuclear Information System (INIS)

Asmolov, V.G.; Volkov, G.A.; Elikin, I.V.; Mysenkov, A.I.

1987-01-01

As is well-known investigations on mathematical models of accidental situations from the point of view of nuclear safety as well as their experimental investigation are of great importance in the design of reactor units for nuclear power plants. This paper gives a review of the state of the art of thermodynamic models and computer codes used for safety analysis of WWER reactors in the USSR, the experimental basis and experimental investigations of the appropriate thermal processes. The actual and future trends of theoretical and experimental investigation on safety problems of WWER type nuclear power plants are briefly described. (author)

Report of a consultants meeting on backfittings and safety enhancement measures in NPPs with WWER 440/213 reactors. Extrabudgetary programme on the safety of WWER NPPS

International Nuclear Information System (INIS)

1994-01-01

The purpose of this Consultants' Meeting held by the IAEA in Vienna from 11-15 April 1994 within the framework of the Extrabudgetary Programme on WWER Safety was to review and analyze safety issues revealed during operation and through analyses of NPPs with WWER 440/213 reactors. The initial list of safety issues based on the available reports from various studies had been prepared by the IAEA secretariat before the meeting, together with indications of safety enhancement measures proposed in various NPP units. During the meeting, the underlying safety concerns and actual technical status of the plants were discussed and the ranking of the safety issues was considered. 58 refs, 1 tab

Perspective decisions of WWER nuclear fuel: Implementation at Russian NPPs

International Nuclear Information System (INIS)

Molchanov, V.

2003-01-01

The scientific and technical policy pursued by JSC TVEL has managed to create a new generation of fuel assembly design on the basis of solutions tested at various units of Russian NPPs - Kola NPP, Kalinin NPP, Unit 1, Balakovo NPP Unit 1. The requirements set for the new generation nuclear fuel for WWER are: 1) High fuel burnup - up to 70 MWxdays/kgU; 2) Extended operation cycle - up to 6 years; 3) Increase of uranium charge to the core; 4) Increased lateral stability - bow not more than 7 mm; 5) High level of operating reliability - fuel rod leakage not worse than 10-5 1/year; 6) Demountable fuel assembly design. Post-irradiation examination results of fuel assemblies discharged from WWER-1000 reactors demonstrate that fuel rods have substantial reserve in general characteristics including that of dealing with planned burnup. In order to meet the requirements, trials are started for: implementation of rigid skeleton (WWER-1000); fuel column length extension (WWER-1000 and WWER-440); increase of UO 2 charge (WWER-1000 and WWER-440); enhancing of operational reliability and demountable design. It is concluded that the Russian nuclear fuel for WWER-type reactors is competitive and enables the implementation of state-of-the-art cost effective fuel cycles

Model experiments on simulation of the WWER water-chemical conditions at loop facilities of the MIR reactor

International Nuclear Information System (INIS)

Benderskaya, O.S.; Zotov, E.A.; Kuprienko, V.A.; Ovchinnikov, V.A.

1999-01-01

The experiments on simulation of the WWER type reactors water-chemical conditions have been started at the State Scientific Center RIAR. These experiments are being conducted at the multi-loop research MIR reactor at the PVK-2 loop facility. The dosage stand was created. It allows introduction of boric acid, potassium and lithium hydroxides, ammonia solutions and gaseous hydrogen. Corrosion tests of the Russian E-635 and E-110 alloys are being conducted at the PVK-2 loop under the WWER water-chemical conditions. If necessary, fuel elements are periodically extracted from the reactor to perform visual examination, to measure their length, diameter, to remove the deposits from the claddings, to measure the burnup and to distribute the fission products over the fuel element by gamma-spectrometry. The chemical analytical 'on line' equipment produced by the ORBISPHERE Laboratory (Switzerland) will be commissioned in the nearest future to measure concentration of the dissolved hydrogen and oxygen as well as pH and specific conductivity. The objective of the report is to familiarize the participants of the IAEA Technical Committee with the capabilities of performing the model water-chemical experiments under the MIR reactor loop facility conditions. (author)

Statistical analysis of the vibration loading of the reactor internals and fuel assemblies of reactor units type WWER-440 from deferent projects

International Nuclear Information System (INIS)

Ovcharov, O.; Pavelko, V.; Usanov, A.; Arkadov, G.; Dolgov, A.; Molchanov, V.; Anikeev, J.; Pljush, A.

2006-01-01

In this paper the following items have been presented: 1) Vibration noise instrument channels; 2) Vibration loading characteristics of control assemblies, internals and design peculiarities of internals of WWER-440 deferent projects; 3) Coolant flow rate through the reactor, reactor core, fuel assemblies and control assemblies for different projects WWER-440 and 4) Noise measurements of coolant speed per channel. The change of auto power spectrum density of absolute displacement detector signal for the last 12 years of SUS monitoring of the Kola NPP unit 2; the coherence functions groups between two SPND of the same level for the Kola NPP unit 1; the measured coolant flow rate at Paks NPP and the auto power spectrum density group of SPND signals from 11 neutron measuring channels of the Kola NPP unit 1 are given. The main factors of vibration loading of internals and fuel assemblies for Kola NPP units 1-4, Bohunice NPP units 1 and 2 and Novovoronezh NPP units 3 and 4 are also discussed

Computerization of the nuclear material accounting system for safeguards purposes at nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Antonov, V.P.; Konnov, Yu.I.; Semenets, A.N.

1983-01-01

The paper sets forth the basic principles underlying nuclear material accounting at nuclear power plants with WWER-440 reactors. It briefly describes the general structure and individual units in a program for computerized accounting. The use of this program is illustrated by the actual accounting data from the fifth unit of the Novovoronezh nuclear power station. The NUMIS program seems to be of interest both for the purposes of IAEA safeguards and for nuclear power plant operators in countries where power plants with WWER-440 reactors subject to IAEA safeguards are either in operation or under construction. The research in question was conducted initially under an IAEA research contract; the system is now being developed further and tested under the IAEA-USSR technical and scientific co-operation programme on safeguards. (author)

Selected safety aspects of containments for nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Jankowski, M.W.; Kulig, M.J.; Strupczewski, A.; Balabanov, E.D.

1996-01-01

Considerable attention has been and continues to be focused on the design and operational features that prevent the release of radioactive materials to the environment for a spectrum of accidents for the two classes of WWER-440 reactors: the older 230 model and the more recently designed 213 models. This paper, based on published and unpublished information, aims to clarify the perceptions of the Russian WWER-440 models 230 and 213 nuclear power plant containment system designs and their relevance to selected aspects of accident mitigation. It should be noted that these are unclearly and often negatively perceived, primarily because of a lack of reliable information and a poorly assembled experimental database. Conflicting statements have been made regarding the nature and the features of the plant's containment system. The paper presents a brief outline of the design of both WWER-440 models with respect to their confinement functions. Selected safety-related aspects of the accident localization systems are discussed, and the recognized shortcomings and safety merits are pointed out. The older 230 units experience high leak rates and are designed to withstand medium-size pipe breaks. The possible implications for safety are pointed out in the paper. The on going studies that concentrate on improving the system are highlighted. (orig.)

On the reliability of steam generator performance at nuclear power plants with WWER type reactors

International Nuclear Information System (INIS)

Styrikovich, M.A.; Margulova, T.Kh.

1974-01-01

The problem of ensuring reliable operation of steam generators in a nuclear power plant with a water-cooled, water-moderated reactor (WWER) was studied. At a nuclear power plant with a vertical steam generator (specifically, a Westinghouse product) the steam generator tubes were found to have been penetrated. Shutdown was due to corrosion disintegration of the austenitic stainless steel, type 18/8, used as pipe material for the heater surface. The corrosion was the result of the action of chlorine ions concentrated in the moisture contained in the iron oxide films deposited in low parts of the tube bundle, directly at the tube plate. Blowing through did not ensure complete removal of the film, and in some cases the construction features of the steam generator made removal of the film practically impossible. Replacement of type 18/8 stainless steel by other construction material, e.g., Inconel, did not give good results. To ensure reliable operation of vertical steam generators in domestic practice, the generators are designed without a low tube plate (a variant diagram of the vertical steam generator of such construction for the water-cooled, water-moderated reactor 1000 is presented). When low tube plates are used the film deposition is intolerable. For organization of a non-film regime a complex treatment of the feed water is used, in which the amount of complexion is calculated from the stoichmetric ratios with the composition of the feed water. It is noted that, if 100% condensate purification is used with complexon processing of the feed water to the generator, we can calculate the surface of the steam-generator heater without considering the outer placement on the tubes. In this the cost of the steam generator and all the nuclear power plants with WWER type reactors is decreased even with installation of a 100% condensate purification. It is concluded that only simultaneous solution of construction and water-regime problems will ensure relaible operation of

Pressurized thermal shock in nuclear power plants: Good practices for assessment. Deterministic evaluation for the integrity of reactor pressure vessel

International Nuclear Information System (INIS)

2010-02-01

Starting in the early 1970s, a series of coordinated research projects (CRPs) was sponsored by the IAEA focusing on the effects of neutron radiation on reactor pressure vessel (RPV) steels and RPV integrity. In conjunction with these CRPs, many consultants meetings, specialists meetings, and international conferences, dating back to the mid-1960s, were held. Individual studies on the basic phenomena of radiation hardening and embrittlement were also performed to better understand increases in tensile strength and shifts to higher temperatures for the integrity of the RPV. The overall objective of this CRP was to perform benchmark deterministic calculations of a typical pressurized thermal shock (PTS) regime, with the aim of comparing the effects of individual parameters on the final RPV integrity assessment, and then to recommend the best practices for their implementation in PTS procedures. At present, several different procedures and approaches are used for RPV integrity assessment for both WWER 440-230 reactors and pressurized water reactors (PWRs). These differences in procedures and approaches are based, in principle, on the different codes and rules used for design and manufacturing, and the different materials used for the various types of reactor, and the different levels of implementation of recent developments in fracture mechanics. Benchmark calculations were performed to improve user qualification and to reduce the user effect on the results of the analysis. This addressed generic PWR and WWER types of RPV, as well as sensitivity analyses. The complementary sensitivity analyses showed that the following factors significantly influenced the assessment: flaw size, shape, location and orientation, thermal hydraulic assumptions and material toughness. Applying national codes and procedures to the benchmark cases produced significantly different results in terms of allowable material toughness. This was mainly related to the safety factors used and the

Neutron flux uncertainty and covariances for spectrum adjustment and estimation of WWER-1000 pressure vessel fluences

International Nuclear Information System (INIS)

Boehmer, Bertram

2000-01-01

Results of estimation of the covariance matrix of the neutron spectrum in the WWER-1000 reactor cavity and pressure vessel positions are presented. Two-dimensional calculations with the discrete ordinates transport code DORT in r-theta and r-z-geometry used to determine the neutron group spectrum covariances including gross-correlations between interesting positions. The new Russian ABBN-93 data set and CONSYST code used to supply all transport calculations with group neutron data. All possible sources of uncertainties namely caused by the neutron gross sections, fission sources, geometrical dimensions and material densities considered, whereas the uncertainty of the calculation method was considered negligible in view of the available precision of Monte Carlo simulation used for more precise evaluation of the neutron fluence. (Authors)

Primary circuit and reactor core T-H characteristics determination of WWER 440 reactors

International Nuclear Information System (INIS)

Hermansky, J.; Petenyi, V.; Zavodsky, M.

2010-01-01

The WWER-440 nuclear fuel vendor permanently improves the assortment of produced nuclear fuel assemblies for achieving better fuel cycle economy and reactor operation safety. During unit refuelling there also could be made some other changes in hydraulic parameters of primary circuit (change of impeller wheels, hydraulic resistance coefficient changes of internal parts of primary circuit, etc.). Therefore it is necessary to determine real coolant flow rate through the reactor during units start-up after their refuelling, and also to have the skilled methodology and computing code for analyzing factors, which affecting the inaccuracy of coolant flow redistribution determination through reactor on flows through separate parts of reactor core in any case of parallel operation of different assembly types. Computing code TH-VCR and CORFLO are used for reactor core characteristics determination for one type of fuel and control assemblies and also in case of parallel operation of different assembly types. The code TH-VCR is able to calculate coolant flow rate for different combinations of three different fuel assembly channel types and three different control assembly channel types. The CORFLO code deals the area of the reactor core which consists of 312 fuel assemblies and 37 control assemblies. Regarding the rotational 60 deg symmetry of reactor core only 1/6 of reactor core with 59 fuel assemblies is taken into account. Computing code CORFLO is verified and validated at this time. Paper presents some results from measurements of coolant flow rate through reactors during start-up after unit refuelling and short description of computing code TH-VCR and CORFLO with some calculated results. (Authors)

SCORPIO - WWER core surveillance system

International Nuclear Information System (INIS)

Hornaes, Arne; Bodal, Terje; Sunde, Svein; Zalesky, K.; Lehman, M.; Pecka, M.; Svarny, J.; Krysl, V.; Juzova, Z.; Sedlak, A.; Semmler, M.

1998-01-01

The Institut for energiteknikk has developed the core surveillance system SCORPIO, which has two parallel modes of operation: the Core Follow Mode and the Predictive Mode. The main motivation behind the development of SCORPIO is to make a practical tool for reactor operators which can increase the quality and quantity of information presented on core status and dynamic behavior. This can first of all improve plant safety, as undesired core conditions are detected and prevented. Secondly, more flexible and efficient plant operation is made possible. The system has been implemented on western PWRs, but the basic concept is applicable to a wide range of reactors including WWERs. The main differences between WWERs and typical western PWRs with respect to core surveillance requirements are outlined. The development of a WWER version of SCORPIO has been done in co-operation with the Nuclear Research Institute Rez, and industry partners in the Czech Republic. The first system is installed at Dukovany NPP, where the Site Acceptance Test was completed 6. March 1998.(Authors)

Definition of the seventh dynamic AER benchmark-WWER-440 pressure vessel coolant mixing by re-connection of an isolated loop

International Nuclear Information System (INIS)

Kotsarev, A.; Lizorkin, M.; Petrin, R.

2010-01-01

The seventh dynamic benchmark is a continuation of the efforts to validate systematically codes for the estimation of the transient behavior of VVER type nuclear power plants. This benchmark is a continuation of the work in the sixth dynamic benchmark. It is proposed to be simulated the transient - re-connection of an isolated circulating loop with low temperature or low boron concentration in a VVER-440 plant. It is supposed to expand the benchmark to other cases when a different number of loops are in operation leading to different symmetric and asymmetric core boundary conditions. The purposes of the proposed benchmark are: 1) Best-estimate simulations of an transient with a coolant flow mixing in the Reactor Pressure Vessel of WWER-440 plant by re-connection of one coolant loop to the several ones on operation, 2) Performing of code-to-code comparisons. The core is at the end of its first cycle with a power of 1196.25 MWt. The basic additional difference of the 7-seventh benchmark is in the detailed description of the downcomer and bottom part of the reactor vessel that allow describing the effects of coolant mixing in the Reactor Pressure Vessel without any additional conservative assumptions. The burn-up and the power distributions at this reactor state have to be calculated by the participants. The thermohydraulic conditions of the core in the beginning of the transient are specified. Participants self-generated best estimate nuclear data is to be used. The main geometrical parameters of the plant and the characteristics of the control and safety systems are also specified. Use generated input data decks developed for a WWER-440 plant and for the applied codes should be used. The behaviour of the plant should be studied applying coupled system codes, which combine a three-dimensional neutron kinetics description of the core with a pseudo or real 3D thermohydraulics system code. (Authors)

Analysis of an accident with the main circulation tube rupture at the WWER-1000

International Nuclear Information System (INIS)

Boyadzhiev, A.I.; Stefanova, S.J.

1984-01-01

In connection with the forthcoming construction of a npp with the wwer-1000 reactor the loss of coolant accident associated with the main circulation tube rupture at the inlet near the reactor is analyzed. The relap4/mod6 program is used for the analysis. The data obtained show that the coolant outflow stage continues for about 25s. On the average the pressure in the circuits varies from 16 to 10 mpa per 0.1s and then it continues to decrease slowly. The pressure in the steam generator at the secondary circuits end increases approximately up to 6.9 MPa as a result of steam generator blocking and remaining coolant heating and then somewhat decreases owing to the primary circuit cooling. By the end of the fuel and can temperatures are equalized and the heat transfer coefficient is stabilized at the level of 100 w/1 (m 2 xK). It is concluded that during a loss of coolant accident at the wwer-1000 reactor in procesess of coolant blowdown in the medium power fuel elemets neither the fuel, melting temperature (3000 k), nor the critical temperature (1000 k) of plastic deformation zirconiu can initiation are attained

Calculations of fission rate distribution in the core of WWER-1000 mock-up on the LR-0 reactor using alternative methods and comparison with results of measurements

International Nuclear Information System (INIS)

Zaritskiy, S.; Kovalishin, A.; Tsvetkov, T.; Rypar, V.; Svadlenkova, M.

2011-01-01

General review of experimental and calculation researches on WWER-440 and WWER-1000 mock-ups on the reactor LR-0 was introduced on the twentieth Symposium AER. The experimental core fission rate distribution was obtained by means of gamma-scanning of the fuel pins - 140La single peak (1596 keV) measurements and wide energy range (approximately 600-900 keV) measurements. Altogether from 260 to 500 fuel pins were scanned in different experiments. The measurements were arranged in the middle of the fuel (the active part of pin). Pin-to-pin calculations of the WWER-1000 mock-up core fission rate distribution were performed with several codes: Monte Carlo codes MCU-REA/2 and MCNPX with different nuclear data libraries, diffusion code RADAR (63 energy groups library) and code SVL based on Surface Harmonics Method (69 energy groups). Calculated data are compared with experimental ones. The obtained results allow developing the benchmark for core calculations methodologies, evaluating and validating source reliability for the out-of-core (inside and outside pressure vessel) neutron transport calculations. (Authors)

Reduction of waste arising as an option for improvement of waste management systems at NPPs with WWER type reactors

International Nuclear Information System (INIS)

Dultchenko, A.; Mikolaitchouk, H.

1995-01-01

After the USSR breakdown Ukraine inherited five NPPs with 12 WWER type reactor units and 4 RBMK type reactor units and no selected disposal site for NPP operational waste and just a few waste treatment facilities which had not been licensed or certified and could not be considered as complying safety requirements and NPP needs. At the same time the lack of competent designer organizations in Ukraine and the overall economical situation including the payment crisis resulted in significant delays in the development of radioactive waste management infrastructure and brought to the foreground a reduction of waste arisings and implementation of waste recycling technologies. In order to evaluate efficiency of waste management systems at Ukrainian NPPs in comparison with current practices at western NPPs and fix main deficiencies and optimum upgrading measures the comparative analyses of waste management systems at Ukrainian NPPs was initiated within the R and D program supported by the Ukrainian State Committee for Nuclear and Radiation Safety (UkrSCNRS). In carrying out the analyses the results of IAEA Technical Assistance Regional project on Advice on Waste Management at WWER type Reactors were used. Taking into account an influence of the Chernobyl accident consequences on the waste management system of Chernobyl NPP the case of Chernobyl NPP was set apart and cannot be considered typical so the authors confine their analysis to the WWER type reactors. For the purposes of comparison the related information about Kozlodui, Paks, Loviisa and Russian NPPs provided under the above-mentioned IAEA Regional Project was used

Fuel Management of WWER-1000 Reactors of Kudankulam Nuclear Power Plant, India

International Nuclear Information System (INIS)

Pandey, Y.; Chauhan, A.

2008-01-01

Two units of WWER-1000 reactors of Russian design are under construction at Kudankulam site in India. These reactors are expected to be commissioned in 2008. The fuel management services for these reactors shall be carried out using Russian Computer codes. This paper includes a brief description of the core, fuel assembly lattice and physics modeling of the lattice and core for these reactors. Presented in this paper are the salient features of the core load pattern designs and fuel performance for 8 operating cycles of these reactors. The paper describes key improvements in the core load pattern designs to enhance the fuel utilization and its thermal behaviour. Presented in the paper are also the on site fuel management strategies with regard to fuel inventory and nuclear material accounting. A computer code for Fuel Inventory and Nuclear Material Accounting (FINMAC) has been developed for this purpose. The code FINMAC takes care of receipt of fresh fuel, flow between various accounting sub areas (ASAs), burnup or production of nuclear isotopes in the reactor cores and discharge from the reactor core. The code generates Material Balance Reports (MBRs) and Composition of Ending Inventory Reports (COEIs) as per the IAEA standards. (authors)

Teaching WWERs at Hacettepe University Nuclear Engineering Department in Turkey

International Nuclear Information System (INIS)

Ergun, S.

2011-01-01

In this study, the challenges faced in the teaching WWER design for the reactor engineering course, which is taught in the Hcettepe University Nuclear Engineering Department are discussed. Since the course is designated taking a western reactor design into account, the computer programs and class projects prepared for the course include models and correlations suitable for these designs. The attempts for modifying the course and developing codes or programs for the course become a challenge especially in finding proper information sources on design in English. From finding proper material properties to exploring the design ideas, teaching WWER designs and using analysis tools for better teaching are very important to modify the reactor engineering course. With the study presented here, the reactor engineering course taught is described, the teaching tools are listed and attempts of modifying the course to teach and analyze WWER designs are explained

Experience in scientific guidance during start-up and normal operation of NPPs with WWER reactors; Opyt nauchnogo rukovodstva puskom i soprovozhdeniya pri ehkspluatatsii ehnergoblokov AEhS s WWER

Energy Technology Data Exchange (ETDEWEB)

Abagyan, A; Kazakov, V; Kryakvin, L [All-Russian Inst. for NPP Operation, Moscow (Russian Federation)

1996-12-31

The experience gained in the All-Russian Research Institute of NPP Operation (RU) in improvement of reactor start-up and normal operation of NPPs has been reported. The work was carried out on NPPs in Russia, Ukraine, Bulgaria, Hungary and Czechoslovakia. All scientific programmes applied use the system approach, modern methods of safety assessment and the principle of loss effect optimization. For the Kozloduy NPP the following projects have been implemented: design of accelerated unloading system for WWER-1000; refinement of water feeding unit for the WWER-1000 steam generator; response analysis of the safety anti-breakdown system of the second loop. The importance of technical substantiation in the process of decision making is stressed. 6 refs.

Reactor pressure vessel embrittlement

International Nuclear Information System (INIS)

1992-07-01

Within the framework of the IAEA extrabudgetary programme on the Safety of WWER-440/230 NPPs, a list of safety issues requiring broad studies of generic interest have been agreed upon by an Advisory Group who met in Vienna in September 1990. The list was later revised in the light of the programme findings. The information on the status of the issues, and on the amount of work already completed and under way in the various countries, needs to be compiled. Moreover, an evaluation of what further work is required to resolve each one of the issues is also necessary. In view of this, the IAEA has started the preparation of a series of status reports on the various issues. This report on the generic safety issue ''Reactor Pressure Vessel Embrittlement'' presents a comprehensive survey of technical information available in the field and identifies those aspects which require further investigation. 39 refs, 21 figs, 4 tabs

Status and prospects of WWER in-core fuel management activities

International Nuclear Information System (INIS)

Novikov, A.N.; Pavlov, V.I.; Pavlovichev, A.M.; Proselkov, V.N.; Saprykin, V.V.

1994-01-01

A short review is given of recent extensive calculational and experimental studies carried out in Russia and Bulgaria for WWER fuel cycle modernization. The main activities performed at Kola NPP, Novovoronezh NPP, Kozloduy NPP and Balakovo NPP are outlined. Based on experience gained, the following improvements in the fuel cycle have been introduced: 1) increased fuel burnup; 2) reduced natural uranium consumption and decreased amount of separation work per energy output unit; 3) increased efficiency of the reactor emergency protection; 4) reduced fast neutron flux onto the reactor vessel. The main characteristics of modernized fuel cycles of WWER-440 and WWER-1000 are presented. 4 tabs., 3 figs., 14 refs

Status and prospects of WWER in-core fuel management activities

Energy Technology Data Exchange (ETDEWEB)

Novikov, A N; Pavlov, V I; Pavlovichev, A M; Proselkov, V N; Saprykin, V V [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)

1994-12-31

A short review is given of recent extensive calculational and experimental studies carried out in Russia and Bulgaria for WWER fuel cycle modernization. The main activities performed at Kola NPP, Novovoronezh NPP, Kozloduy NPP and Balakovo NPP are outlined. Based on experience gained, the following improvements in the fuel cycle have been introduced: (1) increased fuel burnup; (2) reduced natural uranium consumption and decreased amount of separation work per energy output unit; (3) increased efficiency of the reactor emergency protection; (4) reduced fast neutron flux onto the reactor vessel. The main characteristics of modernized fuel cycles of WWER-440 and WWER-1000 are presented. 4 tabs., 3 figs., 14 refs.

Transmutation potential of reactor WWER-440

International Nuclear Information System (INIS)

Darilek, P.; Sebian, V.; Necas, V.

2001-01-01

Theoretical evaluation of WWER-440 transmutation potential by HELIOS - code is presented. Transmutation method proposal comprising special transmutation pins, combined FA and simple reprocessing is described. Transmutation efficiency of the method is characterized (Authors)

Fuel assembly leak tightness control on WWER-1000 reactor

International Nuclear Information System (INIS)

Ivanova, R.; Gerchev, N.; Mateev, A.

2001-01-01

The main index for integrity of the fuel rods cladding is the specific activity value of the primary coolant. This value determines the safe operation of the reactor. The limit for safe operation of WWER-1000 reactor is the value of the total activity of Iodine isotopes in the primary coolant 5.0x10 -3 Ci/l. The paper briefly describes the methodology for performing a fuel tightness test (sipping test) and shows the results from these tests performed during the period 1987 -1999 in units 5 and 6 at the Kozloduy NPP. An additional index related to the safe operation is defined to characterize the fuel cladding integrity Fuel Reliability Index (FRI). The FRI is defined as value of the average activity of 131 I in the primary coolant, corrected with a part of precipitated 235 U migration and fixed to the general permanent purification frequency. Two criteria (quantitative and statistic) are determined to qualify the fuel cladding integrity. The results from sipping tests show good reliability of the fuel irradiated in unit 5 and 6 at the Kozloduy NPP

Steam generator collector integrity of WWER-1000 reactors. IAEA extrabudgetary programme on the safety of WWER NPPs

Energy Technology Data Exchange (ETDEWEB)

Lin, C.; Strupczewski, A. [International Atomic Energy Agency, Vienna (Austria)

1995-12-31

At the Consultants` Meeting on `The Safety of WWER-1000 Model 320 Nuclear Power Plants` organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of WWER-1000 steam generator integrity was identified as an important issue of safety concern. Considering the safety importance of this issue, a Consultants` Meeting on `The Steam Generator Integrity of WWER-1000 Nuclear Power Plants` was convened in Vienna in May 1993, attended by 15 international experts in the area to compile information on the steam generator operating experience, deficiencies and corrective measures implemented and planned. In order to also include information from the main designer OKB Gidropress and to finalize the meeting report the IAEA convened a second meeting on the issue on 23-27 November 1993. The present paper summarizes the information and conclusions from those meetings.

Steam generator collector integrity of WWER-1000 reactors. IAEA extrabudgetary programme on the safety of WWER NPPs

Energy Technology Data Exchange (ETDEWEB)

Lin, C; Strupczewski, A [International Atomic Energy Agency, Vienna (Austria)

1996-12-31

At the Consultants` Meeting on `The Safety of WWER-1000 Model 320 Nuclear Power Plants` organized by the IAEA within the framework of its Extrabudgetary Programme on the Safety of WWER-1000 NPPs, which was held in Vienna, 1-5 June 1992, the problem of WWER-1000 steam generator integrity was identified as an important issue of safety concern. Considering the safety importance of this issue, a Consultants` Meeting on `The Steam Generator Integrity of WWER-1000 Nuclear Power Plants` was convened in Vienna in May 1993, attended by 15 international experts in the area to compile information on the steam generator operating experience, deficiencies and corrective measures implemented and planned. In order to also include information from the main designer OKB Gidropress and to finalize the meeting report the IAEA convened a second meeting on the issue on 23-27 November 1993. The present paper summarizes the information and conclusions from those meetings.

On the heat exchange tube failures in steam generators at NPPs with WWER reactors

International Nuclear Information System (INIS)

Titov, V.F.; Banyuk, G.F.; Brykov, S.I.

1992-01-01

Data on dynamics of failed heat exchanging tube closing in steam generators of NPPs with WWER type reactors for the whole period of their operation are presented. It is shown that the main cause of the tube failures consists in their corrosion cracking under stresses. The effect of chlorine ions on tubes is intensified by the presence of porous sediments on heat exchaning surfaces in quantities exceeding 150 g/m 2

Technology development and production of elongated shell for reactor vessel active zone of WWER-TOI project from steel 15Cr2NiMoVN class 1

International Nuclear Information System (INIS)

Shklyaev, S.Eh.; Titova, T.I.; Ratushev, D.V.; Shul'gan, N.A.; Eroshkin, S.B.; Durynin, V.A.; Efimov, S.V.; Dub, V.S.; Kulikov, A.P.; Romashkin, A.N.

2015-01-01

Production process for the elongated shell blank of the active zone of the reactor pressure vessel made from steel 15Cr2NiMoVN Class 1 with finished sizes Dext=4.655 mm, Dint=4.240 mm, H=4.910 mm (height for heat treatment – 5.750 mm) is presented. For the first time in Russia in production site of OMZ-Special steel LLC a unique elongated shell blank of the reactor vessel active zone was made from ingot 420.0 t for WWER-TOI project fully meeting the specified requirements in terms of metallurgical quality and set of service properties [ru

Results of experimental investigations for substantiation of WWER cermet fuel pin performance

International Nuclear Information System (INIS)

Popov, V.V.; Karpin, A.D.; Isupov, I.A.; Rumyantsev, V.N.; Troyanov, V.M.; Subonyaev, V.N.; Melnichenko, N.A.

1997-01-01

The out-of-pile experiment results on interaction of the cladding and matrix materials and uranium dioxide at cermet fuel temperature for normal operating conditions of the WWER-440 reactor are analyzed. Cermet fuel element behaviour under the maximum designed damage of the WWER-440 reactor is considered. In the AM reactor loop a fission product output from the unsealed cermet fuel elements have been studied. (author). 6 figs, 3 tabs

Method for determining the outlet temperature of fuel assemblies unsupplied with thermometer in WWER-440 reactors

International Nuclear Information System (INIS)

Miko, S.; Kalya, Z.; Hamvas, I.

1987-09-01

The paper outlines a method for the evaluation of the outlet temperatures of fuel assemblies unsupplied with thermometer in WWER-440 reactors. The process is based on interpolation of directly measured assembly temperatures. A quantitative comparison of the errors of described algorithm to those of standard plant-computer interpolation rutine is also presented. (author)

Accident transient processes at NPPs with the WWER type reactors

International Nuclear Information System (INIS)

Bukrinskij, A.M.

1982-01-01

Thermal-physical and nuclear-physical transient processes at NPPs with the WWER type reactors during accidents with the main technological equipment failures and the accidents with loss of coolant in the primary and secondary coolant circuits are considered. Mathematical methods used for these processes modelling is described. Examples of concrete calculations for accidents with different failures are given. Comparative analysis of the results of dynamic tests at the Novo-Voronezh-3 reactor is presented. It is concluded that the modern NPP design is impossible without application of mathematical modelling methods. The mathematical modelling of transients is also necessary for proper and safe NPP operation. Mathematical modelling of accidents at NPPs is a comparatively new method of investigation. Its success and development are completely based on the progress in modern computer development. With their improvement the mathematical models will become more complicate and adequacy of real physical process representation by their means will increase

Verification calculations for the WWER version of the TRANSURANUS code

International Nuclear Information System (INIS)

Elenkov, D.; Boneva, S.; Georgieva, M.; Georgiev, S.; Schubert, A.; Van Uffelen, P.

2006-01-01

The paper presents part of the work performed in the study project 'Research and Development for Licensing of Nuclear Fuel in Bulgaria'. The main objective of the project is to provide assistance for solving technical questions of the fuel licensing process in Bulgaria. One important issue is the extension of the predictive capabilities of fuel performance codes for Russian-type WWER reactors. In the last decade, a series of international projects has been based on the TRANSURANUS fuel performance code: Specific models for WWER fuel have been developed and implemented in the code in the late 90's. In 2000-2003, basic verification work was done by using experimental data of nuclear fuel irradiated in WWER-440 reactors. While the present paper focuses on the analysis of WWER-1000 standard fuel under normal operating conditions, the above study project covers additional tasks: 1) Post-irradiation calculations of ramp tests performed in the DR3 test reactor of the Risoe National Laboratory (five instrumented fuel rods of the Risoe 3 dataset contained in the IFPE database) using the TRANSURANUS code; 2) Compilation of cross-section libraries for isotope evolution calculations in WWER-440 and WWER-1000 fuel assemblies using the ORIGEN-S code; 3) Analysis of current situation and needs for an extension of the curriculum in Nuclear Engineering at the Technical University of Sofia. In this paper the post-irradiation calculations of steady-state irradiation experiments with nuclear fuel for Russian-type WWER-1000 reactors, using the latest release of the TRANSURANUS code (v1m1j03)are presented. Regarding a comprehensive verification of modern fuel performance codes, the burn-up region above 40 MWd/kgU is of increasing importance. A number of new phenomena emerge at high fuel burn-up, implying the need for enlarged databases of postirradiation examinations (PIE). For one fuel assembly irradiated in a WWER-1000 reactor with a rod discharge burn-up between 50 and 55 MWd

WWER-440 local power peaking experiment with/without Hf inserts in the LR-0 reactor

International Nuclear Information System (INIS)

Josek, R.; Hudec, F.; Rypar, V.

2006-01-01

One of the known issues of the WWER-440 reactors is the control rod coupler induced power peaking in the neighbouring fuel assemblies. The effect has been discovered some years ago and is believed to be the cause of several fuel failures during operation in WWER-440 reactors. The effect itself is due to over-moderation and small absorption in the region of control rod coupler, leading to increase in thermal neutron flux and hence to power flare-up in the neighbouring fuel pins. The fuel vendor tackled the problem by attaching hafnium inserts on the inside of the control assembly box. The experiment performed in the LR-0 reactor was focused on the axial and radial power profiles in the vicinity of the control assembly with and without the hafnium inserts. The results of measurements with zero boron concentration are presented. The hafnium insert causes a decrease in peaking factor of about 30% in selected pins close to the control assembly. The measurements are compared with calculations performed with the MCNP-4C code. The compared variables are: the axial fission density distributions; peking factors and peaking factor decrease due to Hf insert. The MCNP results are accurate with respect to the experimental results. A series of benchmarks is being prepared on the basis of these measurements

Identification of the excitation source of the pressure vessel vibration in a Soviet built WWER PWR with signal transmission path analysis

International Nuclear Information System (INIS)

Antonopoulos-Domis, M.; Mourtzanos, K.; Por, G.

1996-01-01

Signal transmission path analysis via multivariate auto-regressive modelling was applied at signals recorded at a WWER power reactor (Paks reactor, Hungary). The core is equipped with strings of self-powered neutron detectors (SPNDs). Each string has seven SPNDs. The signals were high pass filtered with cut-off at 0.03 Hz and low pass-filtered with cut-off at 25 Hz. The analysis suggests that the source of excitation of all signals at 25 Hz is due to main coolant pump vibration. It was confirmed that there is vibration of main coolant pumps at this frequency due to a bearing problem. Signal transmission path analysis also suggests direct paths from outlet coolant to inlet coolant pressure and in-core neutron detectors at the upper part of the core. (author)

Thermal-Hydraulics analysis of pressurized water reactor core by using single heated channel model

Directory of Open Access Journals (Sweden)

Reza Akbari

2017-08-01

Full Text Available Thermal hydraulics of nuclear reactor as a basis of reactor safety has a very important role in reactor design and control. The thermal-hydraulic analysis provides input data to the reactor-physics analysis, whereas the latter gives information about the distribution of heat sources, which is needed to perform the thermal-hydraulic analysis. In this study single heated channel model as a very fast model for predicting thermal hydraulics behavior of pressurized water reactor core has been developed. For verifying the results of this model, we used RELAP5 code as US nuclear regulatory approved thermal hydraulics code. The results of developed single heated channel model have been checked with RELAP5 results for WWER-1000. This comparison shows the capability of single heated channel model for predicting thermal hydraulics behavior of reactor core.

Large-scale experimental facility for emergency condition investigation of a new generation NPP WWER-640 reactor with passive safety systems

Energy Technology Data Exchange (ETDEWEB)

Aniskevich, Y.N.; Vasilenko, V.A.; Zasukha, V.K.; Migrov, Y.A.; Khabensky, V.B. [Research Inst. of Technology NITI (Russian Federation)

1997-12-31

The creation of the large-scale integral experimental facility (KMS) is specified by the programme of the experimental investigations to justify the engineering decisions on the safety of the design of the new generation NPP with the reactor WWER-640. The construction of KMS in a full volume will allow to conduct experimental investigations of all physical phenomena and processes, practically, occurring during the accidents on the NPPs with the reactor of WWER type and including the heat - mass exchange processes with low rates of the coolant, which is typical during the utilization of the passive safety systems, process during the accidents with a large leak, and also the complex intercommunicated processes in the reactor unit, passive safety systems and in the containment with the condition of long-term heat removal to the final absorber. KMS is being constructed at the Research Institute of Technology (NITI), Sosnovy Bor, Leningrad region, Russia. (orig.). 5 refs.

Large-scale experimental facility for emergency condition investigation of a new generation NPP WWER-640 reactor with passive safety systems

International Nuclear Information System (INIS)

Aniskevich, Y.N.; Vasilenko, V.A.; Zasukha, V.K.; Migrov, Y.A.; Khabensky, V.B.

1997-01-01

The creation of the large-scale integral experimental facility (KMS) is specified by the programme of the experimental investigations to justify the engineering decisions on the safety of the design of the new generation NPP with the reactor WWER-640. The construction of KMS in a full volume will allow to conduct experimental investigations of all physical phenomena and processes, practically, occurring during the accidents on the NPPs with the reactor of WWER type and including the heat - mass exchange processes with low rates of the coolant, which is typical during the utilization of the passive safety systems, process during the accidents with a large leak, and also the complex intercommunicated processes in the reactor unit, passive safety systems and in the containment with the condition of long-term heat removal to the final absorber. KMS is being constructed at the Research Institute of Technology (NITI), Sosnovy Bor, Leningrad region, Russia. (orig.)

Large-scale experimental facility for emergency condition investigation of a new generation NPP WWER-640 reactor with passive safety systems

Energy Technology Data Exchange (ETDEWEB)

Aniskevich, Y N; Vasilenko, V A; Zasukha, V K; Migrov, Y A; Khabensky, V B [Research Inst. of Technology NITI (Russian Federation)

1998-12-31

The creation of the large-scale integral experimental facility (KMS) is specified by the programme of the experimental investigations to justify the engineering decisions on the safety of the design of the new generation NPP with the reactor WWER-640. The construction of KMS in a full volume will allow to conduct experimental investigations of all physical phenomena and processes, practically, occurring during the accidents on the NPPs with the reactor of WWER type and including the heat - mass exchange processes with low rates of the coolant, which is typical during the utilization of the passive safety systems, process during the accidents with a large leak, and also the complex intercommunicated processes in the reactor unit, passive safety systems and in the containment with the condition of long-term heat removal to the final absorber. KMS is being constructed at the Research Institute of Technology (NITI), Sosnovy Bor, Leningrad region, Russia. (orig.). 5 refs.

Mathematical modelling of stress-deformation state of the steam generator collector (WWER-type) under pressure loading during fracture mechanics calculations

International Nuclear Information System (INIS)

Zaitsev, M.; Lyssakov, V.

1993-01-01

This paper describes a steam generator collector (WWER-type) designed as part of a Russian reactor power station. The collector is a thick cylindrical shell with a constant inner diameter of 850 mm and a height of 4,970 mm. The wall thickness varies from 78 to 163 mm. In the thicker section, a series of holes allows connection of steam generator heat exchanging tubes. Because of design considerations, the tubes are not symmetrically located about the circumference of the collector. This paper presents a model of the stress concentrations resulting from this design feature for a device operating at a nominal pressure of 16 MPa. 4 refs., 8 figs

Modelling of WWER-1000 fuel: state and prospects

International Nuclear Information System (INIS)

Medvedev, A.; Bibilashvili, Yu.; Bogatyr, S.; Khvostov, G.

1994-01-01

The role of START-3 code in studying and computerized modelling of post-irradiation behaviour of standard fuel rods in real operation conditions of WWER-1000 reactors is described. The models used in the code are based on experimental study of material properties, processes and post irradiation research on standard and experimental fuel pins. The code capability is verified by comparison with data from experiments on WWER test rods performed in MR reactor, the Russia-Finland tests SOFIT and the international program FUMEX. The comparison performed and the results thus obtained demonstrate the satisfactory ability of START-3 code to simulate fuel rod behaviour in normal operation condition. The calculations confirm the experimentally observed evidence of an essential margin on serviceability of WWER-1000 fuel pin with three year operation cycle permitting an increase in design fuel burnup. 2 tabs., 18 figs

Modelling of WWER-1000 fuel: state and prospects

Energy Technology Data Exchange (ETDEWEB)

Medvedev, A; Bibilashvili, Yu; Bogatyr, S; Khvostov, G [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation)

1994-12-31

The role of START-3 code in studying and computerized modelling of post-irradiation behaviour of standard fuel rods in real operation conditions of WWER-1000 reactors is described. The models used in the code are based on experimental study of material properties, processes and post irradiation research on standard and experimental fuel pins. The code capability is verified by comparison with data from experiments on WWER test rods performed in MR reactor, the Russia-Finland tests SOFIT and the international program FUMEX. The comparison performed and the results thus obtained demonstrate the satisfactory ability of START-3 code to simulate fuel rod behaviour in normal operation condition. The calculations confirm the experimentally observed evidence of an essential margin on serviceability of WWER-1000 fuel pin with three year operation cycle permitting an increase in design fuel burnup. 2 tabs., 18 figs.

Key developments in the advanced NPP with WWER-640/V-407 reactor plant design

International Nuclear Information System (INIS)

Dragunov, Yu.G.; Mokhov, V.A.; Nikitenko, M.P.; Afrov, A.M.

1999-01-01

The report covers the main design features of advanced NPP equipped with WWER-640 reactor, that take into account the up-to-date approaches in the process of forming safety concepts. An approach to accident management has been analysed, beyond design-basis accidents included. A description of principal safety systems has been presented as well as the interrelation of their operation. The principal features of the systems design have been shown. (author)

Advanced Approach of Reactor Pressure Vessel In-service Inspection

International Nuclear Information System (INIS)

Matokovic, A.; Picek, E.; Pajnic, M.

2006-01-01

), and it is developed for reactor pressure vessel inspections on the PWR and WWER nuclear power plants. (author)

Advanced fuel cycles for WWER-1000 reactors

International Nuclear Information System (INIS)

Semchenkov, Y. M.; Pavlovichev, A. M.; Pavlov, V. I.; Spirkin, E. I.; Styrin, Y. A.; Kosourov, E. K.

2007-01-01

Main stages of Russian uranium fuel development regarding improvement of safety and economics of fuel load operation are presented. Intervals of possible changes in fuel cycle duration have been demonstrated for the use of current and perspective fuel. Examples of equilibrium fuel load patterns have been demonstrated and main core neutronics parameters have been presented. Problems on the use of axial blankets with reduced enrichment in WWER-1000 fuel assemblies are considered. Some results are presented regarding core neutronic characteristics of WWER-1000 at the use of regenerated uranium and uranium-plutonium fuel. Examples of equilibrium fuel cycles for the core partially loaded with MOX fuel from weapon-grade plutonium are also considered (Authors)

Structural capacity assessment of WWER-1000 MW reactor containment. Progress report

International Nuclear Information System (INIS)

Jordanov, M.

1999-01-01

The objective of the project is to provide assessment of the structural behaviour and safety capacity of the WWER-1000 MW Reactor Building Containment at Kozloduy NPP under critical combination of loads according to the current international requirements. The analysis is focused on a realistic assessment of the Containment taking into account the non-linear shell behaviour of the pre-stressed reinforced concrete structure. Previous assessments of the status of pre stressing cables pointed out that the efficiency of the Containment as a final defence barrier for internal and external events depends on their reliability. Due to this, the experimental data obtained from embedded sensors (gauges) at pre-stressed shell structure is to be compared with the results from analytical investigations. The reliability of the WWER-1000 MW accident prevention system is under evaluation in the project. The Soviet standard design WWER-1000 MW type units installed in Kozloduy NPP were originally designed for a Safe Shutdown Earthquake (SSE) with a peak ground acceleration (PGA) of 0.1g. The new site seismicity studies revealed that the seismic hazard for the site significantly exceeds the originally estimated and a Review Level Earthquake (RLE) anchored to PGA=0.20g was proposed for re-assessment of the structures and equipment at Kozloduy NPP. The scope of the study is a re-assessment of the Containment structure under critical combination of loads according to the current safety and reliability requirements, including comparison between the Russian design requirements and the international regulations. Additionally, an investigation of the pre-stressing technology and the annual control of the cables' pre-stressing of the Containment is to be made. The crane influence on the dynamic behaviour of the Containment will be done as well as a study of the integrity of the Containment as a final defence barrier

The relevance of the IFPE Database to the modelling of WWER-type fuel behaviour

International Nuclear Information System (INIS)

Killeen, J.; Sartori, E.

2006-01-01

The aim of the International Fuel Performance Experimental Database (IFPE Database) is to provide, in the public domain, a comprehensive and well-qualified database on zircaloy-clad UO 2 fuel for model development and code validation. The data encompass both normal and off-normal operation and include prototypic commercial irradiations as well as experiments performed in Material Testing Reactors. To date, the Database contains over 800 individual cases, providing data on fuel centreline temperatures, dimensional changes and FGR either from in-pile pressure measurements or PIE techniques, including puncturing, Electron Probe Micro Analysis (EPMA) and X-ray Fluorescence (XRF) measurements. This work in assembling and disseminating the Database is carried out in close co-operation and co-ordination between OECD/NEA and the IAEA. The majority of data sets are dedicated to fuel behaviour under LWR irradiation, and every effort has been made to obtain data representative of BWR, PWR and WWER conditions. In each case, the data set contains information on the pre-characterisation of the fuel, cladding and fuel rod geometry, the irradiation history presented in as much detail as the source documents allow, and finally any in-pile or PIE measurements that were made. The purpose of this paper is to highlight data that are relevant specifically to WWER application. To this end, the NEA and IAEA have been successful in obtaining appropriate data for both WWER-440 and WWER-1000-type reactors. These are: 1) Twelve (12) rods from the Finnish-Russian co-operative SOFIT programme; 2) Kola-3 WWER-440 irradiation; 3) MIR ramp tests on Kola-3 rods; 4) Zaporozskaya WWER-1000 irradiation; 5) Novovoronezh WWER-1000 irradiation. Before reviewing these data sets and their usefulness, the paper touches briefly on recent, more novel additions to the Database and on progress made in the use of the Database for the current IAEA FUMEX II Project. Finally, the paper describes the Computer

Trends and results in In-Core management for the Kozloduy NPP WWER-440 reactors

International Nuclear Information System (INIS)

Haralampieva, Tz.; Antov, A.; Georgieva, N.; Spasova, V.

2001-01-01

The paper presents the experience gained during the design and operation of the last fuel cycles of the four WWER-440/V-230 units at Kozloduy NPP. High efficiency and economy of the fuel utilization requires very precise procedures for fuel in-core management, including calculations and analyses for reloading scheme design, compared with results from operational measurements and fuel cycle efficiency. The paper describes the main stages of implementation of advanced fuel assemblies in the Kozloduy NPP WWER-440 reactors. New advanced fuel has been implemented after the completion of comprehensive neutron-physical, thermal-hydraulic and thermal-mechanical analyses by using advanced computer codes. As a general task of the fuel cycle improvements it is pointed the increasing of the final fuel burnup and decreasing of the number of spent fuel assemblies. Series of calculations and analyses, related to the introducing of the advanced fuel assemblies and improvement of the fuel cycle characteristics have been carried out to guarantee the safe operation and fuel reliability

Analysis of the effect of implemented low temperature overpressure regimes on the reactor pressure vessel resistance to damage

International Nuclear Information System (INIS)

Pistora, V.

1995-12-01

The temperature and stress fields of the Dukovany WWER-440 reactor pressure vessel (RPV) were calculated based on a two-dimensional model using the finite element method. Two pressurized thermal shock events occurred at Dukovany in 1992: the temperature in 3 loops dropped rapidly while the primary circuit was fully pressurized. The calculation revealed that the first event was intolerable with respect to the RPV resistance to brittle fracture; had the two events occurred towards the end of the RPV lifetime, both would have been intolerable. (M.D.). 6 tabs., 15 figs., 6 refs

Power peak in vicinity of WWER-440 control assembly

International Nuclear Information System (INIS)

Mikus, J.

2002-01-01

This paper presents information concerning the WWER-440 local power peaking problem induced by a control assembly and corresponding investigation possibilities on the light-water zero-power reactor LR-O at the Nuclear Research Institute Rez plc. Brief description of the disposable CA model, experimental arrangement and conditions on the LR-O reactor, preparation of the relevant measurements in the WWER-440 type cores with CA model, as well as some preliminary results of the fission density distribution obtained in a core without boron and with fuel assemblies having profiled enrichment are mentioned too (Author)

Researches of WWER fuel rods behaviour under RIA accident conditions

International Nuclear Information System (INIS)

Nechaeva, O.; Medvedev, A.; Novikov, V.; Salatov, A.

2003-01-01

Unirradiated fuel rod and refabricated fuel rod tests in the BIGR as well as acceptance criteria proving absence of fragmentation and the settlement modeling of refabricated fuel rods thermomechanical behavior in the BIGR-tests using RAPTA-5 code are discussed in this paper. The behaviour of WWER type simulators with E110 and E635 cladding was researched at the BIGR reactor under power pulse conditions simulating reactivity initiated accident. The results of the tests in four variants of experimental conditions are submitted. The behaviour of 12 WWER type refabricated fuel rods was researched in the BIGR reactor under power pulse conditions simulating reactivity initiated accident: burnup 48 and 60 MWd/kgU, pulse width 3 ms, peak fuel enthalpy 115-190 cal/g. The program of future tests in the research reactor MIR with high burnup fuel rod (up to 70 MWd/kgU) under conditions simulating design RIA in WWER-1000 is presented

An approach to WWER fuels with BaCo

International Nuclear Information System (INIS)

Marino, A.; Demarco, G.

2008-01-01

BaCo is a code for the simulation of the behaviour of a nuclear fuel rod under operation conditions. BaCo, a quasi 2D code based on a finite differences scheme, has been used for simulating PHWR, CANDU, PWR, BWR, MOX, WWER, and experimental fuel rods. We improve the performance of BaCo with a set of tools based on the method of finite elements for 3D analysis of the stress-strain state. We can simulate any UO 2 pellet geometry. Standard WWER-440 fuel assemblies irradiated in the Kola-3 reactor of the CRP FUMEX II of the IAEA were the first WWER simulations with BaCo. We find a very good agreement among our calculations, the experimental results and other qualified fuel codes. We present the BaCo code and our results for PWR and WWER fuels of the CRP FUMEX II, the 3D analysis of WWER fuel pellet and the projections of these results with the Argentinean nuclear fuels development. (authors)

Experience in decontamination of the equipment of NPP's with the WWER-440 reactors

International Nuclear Information System (INIS)

Balaban-Irmenin, Yu.V.

1981-01-01

Different methods of decontamination at NPPs are briefly characterized. Decontamination of the removable part of the main circulation pump (MCP) of the WWER-440 reactor is considered as an example of removable equipment decontamination. A design of the decontamination bath of the removable MCP elements and the applied chemical agents are described. A decontamination flowsheet of the Novovoronezh NPP steam generator (SG) is considered as an example of the autonomic decontamination system. The SG decontamination modes, principal flowsheets of a hydromonitor, steam-ejection sprayer and steam-emulsion device are described [ru

WWER radial reflector modeling by diffusion codes

International Nuclear Information System (INIS)

Petkov, P. T.; Mittag, S.

2005-01-01

The two commonly used approaches to describe the WWER radial reflectors in diffusion codes, by albedo on the core-reflector boundary and by a ring of diffusive assembly size nodes, are discussed. The advantages and disadvantages of the first approach are presented first, then the Koebke's equivalence theory is outlined and its implementation for the WWER radial reflectors is discussed. Results for the WWER-1000 reactor are presented. Then the boundary conditions on the outer reflector boundary are discussed. The possibility to divide the library into fuel assembly and reflector parts and to generate each library by a separate code package is discussed. Finally, the homogenization errors for rodded assemblies are presented and discussed (Author)

Fuel pin failure root causes and power distribution gradients in WWER cores

International Nuclear Information System (INIS)

Mikus, J.

2008-01-01

The purpose of this work is to investigate the influence of some core heterogeneities and reactor construction materials on space power distribution in WWER type cores, especially from viewpoint of the values and gradient occurrence that could result in static loads with some consequences, e.g., fuel pin (FP) or fuel assembly (FA) bowing and possible contribution to the FP failure root causes. Presented information were obtained by means of experiments on research reactor LR-0 concerning the: 1) Power distribution estimation on pellet surface of the FPs neighbouring a FP containing gadolinium (Gd 2 O 3 ) burnable absorber integrated into fuel in WWER-440 and -1000 type cores; 2) Power distribution measurement in periphery FAs neighbouring the baffle in WWER-1000 type cores and 3) Power distribution in FAs neighbouring the control rod absorbing part in a WWER-440 type core. (author)

Burnup influence on the WWER-1000 reactor vessel neutron fluence evaluation

International Nuclear Information System (INIS)

Panayotov, I.; Mihaylov, N.; Ilieva, K.; Kirilova, D.; Manolova, M.

2009-01-01

The neutron fluence of the vessels of the reactors is determined regularly accordingly the RPV Surveillance Program of Kozloduy NPP Unit 5 and 6 in order to assess the state of the metal vessel and their radiation damaging. The calculations are carried out by the method of discrete ordinates used in the TORT program for operated reactor cycles. An average reactor spectrum corresponding to fresh U-235 fuel is used as an input neutron source. The impact of the burn up of the fuel on the neutron fluence of WWER-1000 reactor vessel is evaluated. The calculations of isotopic concentrations of U-235 and Pu-239 corresponding to 4 years burn up were performed by the module SAS2H of the code system SCALE 4.4. Since fresh fuel or 4 years burn up fuel assembly are placed in periphery of reactor core the contribution of Pu-239 of first year burn up and of 4 years burn up is taken in consideration. Calculations of neutron fluence were performed with neutron spectrum for fresh fuel, for 1 year and for 4 years burn up fuel. Correction factors for neutron fluence at the inner surface of the reactor vessel, in ? depth of the vessel and in the air behind the vessel were obtained. The correction coefficient could be used when the neutron fluence is assessed so in verification when the measured activity of ex-vessel detectors is compared with calculated ones. (Authors)

Improvement of operational performance and increase of safety of WWER-1000/V-392

International Nuclear Information System (INIS)

Kurakov, Y.A.; Dragunov, Y.G.; Podshibiakin, A.K.; Fil, N.S.; Krushelnitsky, V.N.; Berkovich, V.M.

2001-01-01

The national programme of nuclear power development approved by the Russian Federation Government in 1998 considers the design of WWER-1000/V-392 power unit as a priority project of the new generation NPP with improved operational performances and increased safety. The pilot unit of this design (NVAES-2) is licensed for construction at the Novovoronezh NPP site. The NVAES-2 design is developed on the basis of standard power unit with reactor plant V-320. Twenty units of this type are in operation at the nuclear power plants in Russia, Ukraine and Bulgaria having totally about 270 reactor-years of operation. Two more V-320 units are being commissioned this year at Rostov NPP and Temelin NPP. So, the WWER-1000/V-392 design is as a whole an evolutionary development of the operating standard unit WWER-1000/V-320. Many technical solutions aimed at increase of safety and improvement of operational performance of the plant are implemented in the NVAES-2 design, such as advanced reactor WWER-1000, passive system of residual power removal, passive system of the core flooding under loss-of-coolant accidents, and others. NVAES-2 design refers to a class of advanced light water reactors and corresponds to the international requirements imposed to the nuclear power plants to be put into operation after the year 2000. New V-392 power unit has a good perspective from the view point of extensive implementation in the framework of the nuclear electricity production in Russia. Design decisions on NVAES-2 power unit with WWER-1000/V-392 reactor plant which assure significantly higher safety level and improve economical performance as compared to the operating WWER-1000 units are briefly considered in the present paper. (author)

Radioactive waste management in nuclear power plants with WWER-type reactors

Energy Technology Data Exchange (ETDEWEB)

Dlouhy, Z; Napravnik, J; Safar, O

1975-05-01

The possibilities of radioactive waste solidification in nuclear power plants with LWR reactors (of the WWER type) and the problems of their safe storage in Czechoslovakia are discussed. The most suitable method for the treatment of emitted sorbents and concentrates seems to be their incorporation in bitumen or concrete. In the disposal of solidified blocks all requirements should be met including the selection of suitable sites and of convenient methods of transportation. A preliminary economic estimate shows that the storage of bitumen-incorporated wastes in trenches seems to be less expensive from the point of view of exploitation of the storage facility as well as from the point of view of investment.

Application of modified version of SPPS-1 - HEXAB-2DB computer code package for operational analyses of fuel behaviour in WWER-440 reactors at Kozloduy NPP

Energy Technology Data Exchange (ETDEWEB)

Kharalampieva, Ts; Stoyanova, I; Antonov, A; Simeonov, T [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Petkov, P [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika

1994-12-31

The modified version of SPPS-1 code called SPPS-1-HEXAB-2DB was applied for the purposes of the operational analysis and power peaking factors and reactor core critical parameters predictions of WWER-440s. The results of the calculations performed by the use of SPPS-1-HEXAB-2DB code and the corresponding parameters obtained from experiments at Kozloduy NPP WWER-440s as well as the results of fuel rod power distribution are presented. The method of operation simulation of reactor core with 349 assemblies (Unit 4) and with 313 fuel assemblies and 36 dummy fuel assemblies (Unit 1) is outlined. The modified code calculates not only fuel burnup and Pm-149 and Sm-149 concentrations distributions but also the space distribution of I-135 and Xe-135 concentrations. In this way it makes possible to perform the reactor operation simulation during the immediate periods after the reactor start-up or shut-down and to predict the critical reactor core parameters during transients. The results obtained show that SPPS-1-HEXAB-2DB code describes adequately the reactor core status. The new SPPS-1 code algorithm for estimation of assembly-wise power peaking factors distribution in reactor core is also described. The new code provides an option for checking the correctness of reactor core symmetry. The experience from the use of the modified SPPS-1-HEXAB-2DB code system confirms the provision of improved availability of operational analysis, prediction of Kozloduy NPP WWER-440s safe operations and fuel behaviour estimation. 14 tabs., 4 figs., 5 refs.

Experience of CR and RCCA operation in Ukrainian WWER-1000: Aspects of reliability, safety and economic efficiency

International Nuclear Information System (INIS)

Afanasyev, A.

2000-01-01

The next topics are represented in the paper: A brief history of WWER-1000 control rod (CR) and WWER-1000 rod cluster control assembly (RCCA) design; Evolution of WWER-1000 CR manufacturing technology and design; Experience of RCCA operation; Lifetime extension of WWER-1000 boron carbide CR; WWER-1000 reactor core operation problems due to partial RCCA insertion; Designing and licensing procedures and first operational experience of WWER-1000 RCCA (CR) with a combined absorber 'boron carbide-hafnium' and a chromium-nickel alloy cladding. The main conclusions are: Fuel assembly (FA) bow is the main reason of partial RCCA insertion during reactor core operation. However, the use of the RCCA and its driver bar with increased dead load, alongside with other measures, allow to reduce the probability of incomplete RCCA insertion; The materials used in CRs of RCCA in existing reactor operating modes have been working reliably; The use of hafnium under an appropriate price policy can give certain economic advantages for the Ukrainian NPPs, however, additional research is needed in order to confirm the specific CR physical characteristics and reliability. (author)

WWER water chemistry related to fuel cladding behaviour

Energy Technology Data Exchange (ETDEWEB)

Kysela, J; Zmitko, M [Nuclear Research Inst. plc., Rez (Czech Republic); Vrtilkova, V [Nuclear Fuel Inst., Prague (Czech Republic)

1997-02-01

Operational experience in WWER primary water chemistry and corrosion related to the fuel cladding is reviewed. Insignificant corrosion of fuel cladding was found which is caused by good corrosion resistance of Zr1Nb material and relatively low coolant temperature at WWER-440 reactor units. The differences in water chemistry control is outlined and an attention to the question of compatibility of Zircaloys with WWER water chemistry is given. Some results of research and development in field of zirconium alloy corrosion behaviour are discussed. Experimental facility for in-pile and out-of-pile cladding material corrosion testing is shown. (author). 14 refs, 5 figs, 3 tabs.

Development of new chemical and electrochemical decontamination methods for selected equipment of WWER-440 and WWER-1000 reactor primary circuit

International Nuclear Information System (INIS)

Solcanyi, M.; Majersky, D.

1998-01-01

Special devices for in-situ application of decontamination technologies assigned for Steam Generator, Pressurizer and Main Circulating Casing of WWER-1000 type were designed, manufactured and tested in real conditions of their use in above Primary Circuit components. New decontamination technologies like low-concentration process NP-NHN for the decontamination of the Steam Generator, combined chemico-mechanical treatment for the Pressurizer and semi-dry electrolysis for the Main Circulating Pump Casing were developed and approved for their safe plant application from point of view of decontamination efficiency, corrosion influence and processing of secondary wastes. Main technological parameters were defined to achieve high decontamination efficiency and corrosion-safe application of all decontamination technologies. (author)

Current state of WWER SNF storage in Russia and the perspectives

International Nuclear Information System (INIS)

Anisimov, O.; Kozlov, Y.; Razmashkin, N.; Safutin, V.; Tikhonov, N.

2006-01-01

In the Russian Federation WWER-440 Spent Nuclear Fuel (SNF) is reprocessed at RT-1 plant near Cheliabinsk. WWER-1000 SNF is supposed to be reprocessed at RT-2 plant, which will be built about 2020. The information on the capacity and fill up level of the at-reactor pools at NPP with WWER reactors considering its modification up to May 2005 is given. The regulatory requirements to all SNF 'wet' storage facilities; the principle design and engineering solutions as well as the complex of measures for radiation safety and the environmental protection of spent fuel storage are presented. WWER-440 SNF management, WWER-1000 SNF management and dry storage of WWER-1000 SNF are discussed. In the conclusion it is noted than neither Russia, nor any other country have the experience of construction of vault-type 'dry' storage facilities of such a capacity to store WWER-1000 SNF (9000 tU). The experience and design solutions approved earlier in creation of other dangerous facilities were used. The calculations were based on conservative assumptions allowing with a large assurance to guarantee the nuclear and radiation safety and the environmental protection. At present, a program is developed for scientific-technical support of the dry storage facility design and operation, aimed at the studies whose results will allow to optimize the taken technical decisions, simplify SNF management technology and, possibly, to reduce the cost of the storage facility itself

Studying some regimes of the WWER-440 type reactor failed fuel element operation

International Nuclear Information System (INIS)

Aksenov, N.A.; Samsonov, B.V.; Sulaberidze, V.Sh.; Frej, A.K.

1981-01-01

The results of investigating the serviceability of experimental fuel elements close by type to that of the WWER-440 type reactor in the cans of which untightness in the form of small opening are made. The tests are carried out in the SM-2 reactor high temperature water loop at the temperature of 473 K, pressure of (1-2)x10 4 kPa, coolant flow rate of 3.7-5.5 m 3 /h. The analysis of the obtained results shows that the character of changes in the fission product (FP) activity in the circuit in a considerable extent is determined bt the thermal-optical conditions of the fuel element operation. If water in the gap between fuel and can does not boil, activity changes smoothly and bursts caused by increased FP release are observed only under transient conditions of reactor operation. In the presence of water boiling in the gap the FP release has of impulse character with the frequency determined besides the untightness dimension by free volume inside the fuel element can (with its increase the pulsation frequency increases). FP release from fuel is connected with their direct escape from an open surface. When water in the gap the FP release from the fuel element occurs practically immediately. Without boiling the FP delay in the gap is determined by their diffusion in a layer of water. The conclusion is drawn that the FP release from failed fuel elements may be reduced by eliminating the water boiling in the gap between the fuel and the can by means of the fuel element power or coolant temperature decrease

Safety and upgrading of nuclear power plants with WWER-440/V-230; Voprosy bezopasnosti i modernizatsii AEhS s WWER-440 (V-230)

Energy Technology Data Exchange (ETDEWEB)

Melnikov, N [Opytno-Konstruktorskoe Byuro Gidropress, Podol` sk (Russian Federation)

1996-12-31

Modernization of WWER-440/V-230 reactors is considered according to the WANO project `Proposal for reconstruction of WWER-440/V-230 reactors` (1990). The main technical measures to be taken relate to: 1. Expanding the considered spectrum of design basis accidents; 2. Provision of first loop integrity; 3. Safety system structure and components reliability enhancement; 4. Reduction o initiating events probability; 5. Enhancement of hermeticity and integrity of the area surrounding the first loop; 6. Fire fighting system upgrade; 7. Radiation control system upgrade; 8. Provision of seismic resistance. Details of the recommended technical steps for some NPPs are presented. 1 tab.

Boiling water reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and workshop material and sponsors workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series No. 12, 'Reactor Simulator Development' (2001). Course material for workshops using a WWER- 1000 simulator from the Moscow Engineering and Physics Institute, Russian Federation is presented in the IAEA publication: Training Course Series No. 21 'WWER-1000 Reactor Simulator' (2002). Course material for workshops using a pressurized water reactor (PWR) simulator developed by Cassiopeia Technologies Incorporated, Canada, is presented in the IAEA publication: Training Course Series No. 22 'Pressurized Water Reactor Simulator' (2003). This report consists of course material for workshops using a boiling water reactor (BWR) simulator. Cassiopeia Technologies Incorporated, developed the simulator and prepared this report for the IAEA

A study of the pressure vessel steel of the WWER-440 unit 1 of the Kozloduy nuclear power plant

Science.gov (United States)

Kostadinova, E.; Velinov, N.; Avdjieva, T.; Mitov, I.; Rusanov, V.

2017-11-01

A comparison between highly neutron irradiated samples from the region of weld № 4 and low irradiated samples from weld № 1 taken from the pressure vessel of the WWER-440 Unit № 1 of the Kozloduy NPP has been performed. Measurements of the residual activity of samples from the outer surface of the reactor pressure vessel bottom corpus reveal very low activity of 60Co. Insofar as there the base and weld metal appear to be exposed to a very low neutron fluence, the samples from these locations can be considered as practically not affected and may serve as a reference basis for comparison with highly irradiated pressure vessel regions. The Mössbauer parameters isomer shift (IS) and quadrupole splitting (QS) were found to be absolutely irradiation insensitive. A stepwise reduction of the internal hyperfine magnetic field Bhf, each by about 2.6 T, was observed. This can be attributed to the replacement of one or two surrounding iron atoms as first nearest neighbors by non-iron alloying atoms. The Mössbauer experimental line widths for irradiated and non-irradiated samples are practically the same, which is a quite unexpected result. The area fraction ratio for the three main Zeeman sextet subspectra S1:S2:S3 shows very high irradiation sensitivity. For the bottom low irradiated region of the reactor vessel the values are S1:S2:S3 = 50.1:40.0:9.4. After seven years of operation between the pressure vessel annealing in 1989 and the autumn of 1996 when the samples from weld № 4 were taken the ratio changes strongly to S1:S2:S3 = 56.4:34.7:8.5. A possible explanation of this result is that neutron irradiation gives rise to a precipitation process involving predominantly alloying atoms as Ni, Mn, Cr, Mo and V which become mobile and precipitate in the form of carbides and/or P-rich phases and alloying atom aggregates. This "refinement" process lowers the partial area of subspectra S2 and S3 where alloying atoms are involved and leads to a higher area fraction of

Comment on the in-core measurement in the WWER nuclear power plant

International Nuclear Information System (INIS)

Krett, V.; Dach, K.; Erben, O.

1985-01-01

The activity of the Nuclear Research Institute (NRI) Rez in the field of in-core measurement sensors is described in the paper. The results of comparison and calibration experiments realized on the WWR-S research reactor at the NRI are presented. Measurements with fission calorimeters and SPN detectors carried out in the framework of diagnostic fuel assembly program of WWER NPP reactors are described. Noise measurements with detectors of in-core instrumentation of diagnostic fuel assemblies are also mentioned. Comparison experiments on the WWER-440 NPP reactor are described and the method of function verification of neutron sensors of the in-core control system of these reactors is given. (author)

Safety aspects of neutron noise diagnostics and loose parts monitoring in WWER reactors

International Nuclear Information System (INIS)

Por, G.

1997-01-01

In this paper our aim is to give very short introduction on different types of well selected noise diagnostics methods and then mentioning their occurrence in WWER reactors we analyze what impact they might have to operational safety and for ageing (which also affects on safety of the installations). We do not deny, that one of our main aim is to call the attention of management staff of NPP, which deals with safety, safety culture, maintenance and operation proving, that such methods and system can give not only benefit to economy but also impact on safety of nuclear installations. 14 refs, 6 figs

OPAL- the in-core fuel management code system for WWER reactors

International Nuclear Information System (INIS)

Krysl, V.; Mikolas, P.; Sustek, J.; Svarny, J.; Vlachovsky, K.

2002-01-01

Fuel management optimization is a complex problem namely for WWER reactors, which at present are utilizing burnable poisons (BP) to great extent. In this paper, first the concept and methodologies of a fuel management system for WWER 440 (NPP Dukovany) and NPP WWER 1000 (NPP Temelin) under development in Skoda JS a.s. are described and followed by some practical applications. The objective of this advanced system is to minimize fuel cost by preserving all safety constraints and margins. Future enhancements of the system will allow is it to perform fuel management optimization in the multi-cycle mode. The general objective functions of the system are the maximization of EOC reactivity, the maximization of discharge burnup, the minimization of fresh fuel inventory / or the minimization of feed enrichment, the minimization of the BP inventory. There are also safety related constraints, in which the minimization of power peaking plays a dominant role. The core part of the system requires meeting the major objective: maximizing the EOC Keff for a given fuel cycle length and consists of four coupled calculation steps. The first is the calculation of a Loading Priority Scheme (LPS). which is used to rank the core positions in terms of assembly Kinf values. In the second step the Haling power distribution is calculated and by using fuel shuffle and/or enrichment splitting algorithms and heuristic rules the core pattern is modified to meet core constraints. In this second step a directive/evolutionary algorithm with expert rules based optimization code is used. The optimal BP assignment is alternatively considered to be a separate third step of the procedure. In the fourth step the core is depleted in normal up to 3D pin wise level using the BP distribution developed in step three and meeting all constraints is checked. One of the options of this optimization system is expert friendly interactive mode (Authors)

Substantiation of operation limits of reactivity insertion during WWER-1000 reactors start-up; Obosnovanie ehkspluatatsionnykh predelov vvoda reaktivnosti pri puske reaktorov WWER-1000

Energy Technology Data Exchange (ETDEWEB)

Boev, I; Sabitov, A; Sal` kov, V; Sudarev, O; Yakovlev, A [ATOMTECHENERGO RF, Novovoronezh (Russian Federation)

1996-12-31

The methods and programmes used to define the tolerable rate of reactivity insertion during WWER-1000 start-up are presented. They include calculation of the neutron source power in the core during the sub-critical stage and calculation of the relative neutron density and reactor period during the critical stage. The need for optimisation and regulation of tolerable rates is discussed along with the tool parameters affecting the reactivity during start-up. The possibility of increasing the feed rate of pure condensate into the first loop during the time needed to reach critical stage is justified. 4 refs., 3 tabs.

Innovation of genetic algorithm code GenA for WWER fuel loading optimization

International Nuclear Information System (INIS)

Sustek, J.

2005-01-01

One of the stochastic search techniques - genetic algorithms - was recently used for optimization of arrangement of fuel assemblies (FA) in core of reactors WWER-440 and WWER-1000. Basic algorithm was modified by incorporation of SPEA scheme. Both were enhanced and some results are presented (Authors)

Review of RIA and LOCA criteria for WWER fuel

International Nuclear Information System (INIS)

Hozer, Z.

2006-01-01

The RIA and LOCA fuel safety criteria are under revision in the international community of fuel suppliers, authorities and research organizations. The main criteria will be reviewed in the paper for WWER fuel. Experimental data on the fuel failure behaviour under reactivity-initiated accident (RIA) conditions produced in the last decade in French and Japanese test reactors indicated low failure enthalpy for high burnup fuel compared to fresh fuel. However the high burnup was not the only phenomenon influencing the fuel failure. The oxide scale on the external surface of the fuel rod, hydrogen content of the Zr cladding and the local hydriding seemed also be responsible for the failure at low enthalpy. Furthermore differences have been found between Western design fuel and Russian type WWER fuel. The burnup dependence of fuel failure for WWER fuel was found much less, probably due to the low oxidation during normal operational conditions compared to other PWRs. The recently published Vitanza and KAERI correlations for RIA failure enthalpy have been applied to 23 WWER tests. Experimental data from Russian IGR and BIGR reactors have been used. The calculations have shown that both burnup and cladding oxidation effects must be considered, however the pulse width dependence of failure enthalpy has not been confirmed. During loss of coolant accidents (LOCA) the peak cladding temperature and local oxidation criteria have to be met. The oxidation criterion is under discussion today in many laboratories. The AEKI carried out several experimental series with Zr1%Nb cladding used in WWER reactors. The paper will describe the main results of the tests and present the limit for ductile-brittle transition derived from ring compression test. The behaviour of Zr1%Nb (E110) and Zircaloy-4 claddings under LOCA conditions will be compared as well. (author)

Overview of input parameters for calculation of the probability of a brittle fracture of the reactor pressure vessel

International Nuclear Information System (INIS)

Horacek, L.

1994-12-01

The parameters are summarized for a calculation of the probability of brittle fracture of the WWER-440 reactor pressure vessel (RPV). The parameters were selected for 2 basic approaches, viz., one based on the Monte Carlo method and the other on the FORM and SORM methods (First and Second Order Reliability Methods). The approaches were represented by US computer codes VISA-II and OCA-P and by the German ZERBERUS code. The philosophy of the deterministic and probabilistic aspects of the VISA-II code is outlined, and the differences between the US and Czech PWR's are discussed in this context. Briefly described is the partial approach to the evaluation of the WWER type RPV's based on the assessment of their resistance to brittle fracture by fracture mechanics tools and by using the FORM and SORM methods. Attention is paid to the input data for the WWER modification of the VISA-II code. The data are categorized with respect to randomness, i.e. to the stochastic or deterministic nature of their behavior. 18 tabs., 14 refs

Fuel and fuel cycles with high burnup for WWER reactors

International Nuclear Information System (INIS)

Chernushev, V.; Sokolov, F.

2002-01-01

The paper discusses the status and trends in development of nuclear fuel and fuel cycles for WWER reactors. Parameters and main stages of implementation of new fuel cycles will be presented. At present, these new fuel cycles are offered to NPPs. Development of new fuel and fuel cycles based on the following principles: profiling fuel enrichment in a cross section of fuel assemblies; increase of average fuel enrichment in fuel assemblies; use of refuelling schemes with lower neutron leakage ('in-in-out'); use of integrated fuel gadolinium-based burnable absorber (for a five-year fuel cycle); increase of fuel burnup in fuel assemblies; improving the neutron balance by using structural materials with low neutron absorption; use of zirconium alloy claddings which are highly resistant to irradiation and corrosion. The paper also presents the results of fuel operation. (author)

Safety of WWER type nuclear power plants - viewing from Hungary

International Nuclear Information System (INIS)

Voeroess, L.

1991-01-01

An evaluation of WWER type nuclear power plants operating in Hungary is given, relative to the safety requirements accepted internationally; how safe can they be regarded and what can be done to assure a high level of safety in all case. After an overview of general safety criteria, an overall description of WWER-440 type nuclear reactors is presented. Design safety, operational safety issues are treated in detail. Safety inspection and safety-related research and development is discussed. Regarding the future, five different issues associated with nuclear reactor safety should be considered. (R.P.) 20 refs.; 12 figs.; 3 tabs

Using noise diagnostics for detection and monitoring of vibrations of RPV internals, and for cause analysis in Eastern German NPP with WWER-440/230 type reactors of the Russian design type

International Nuclear Information System (INIS)

Schumann, P.

2000-10-01

The report explains in detail applications and results of noise diagnostic measurements for examining vibrations which caused damage to reactor pressure vessel internals. The vibrations investigated were observed in 1975 and 1985 at the WWER-440/230 type reactors of the Russian design installed in units 1 and 2 of the Greifswald nuclear power plant, and were identified as dominant control element vibrations and abnormal core basket movements. The report presents essential operating characteristics recorded during disturbed reactor operation, the inspection results, and characteristic experimental findings from noise signal analyses and special tests examining the physical aspects of the vibration processes and their causes. Some recommendations have been derived relating to monitoring and minimization of such vibrations. (orig./CB) [de

Assesment criteria improvement for operational economical efficiency of NPP with WWER typr reactors

International Nuclear Information System (INIS)

Abagyan, A.A.; Matveev, A.A.; Ignatenko, E.I.; Pshechenkova, T.V.

1983-01-01

A new technique for calculating fuel component of the cost of NPP electric power generation is suggested. To calculate the variable part of fuel component it is suggested to consider the acquisition cost of fuel assemblies, unloaded from the reactor on fuel cycle completion instead of acquisition cost of fresh fuel assemblies, loaded into the reactor for organization of this cycle; it is also suggested to include the acquisition cost of fuel assemblies, remaining in reactop core on completion of the last fuel cycle+ in constant fuel expenses. The fuel component of the cost of WWER-440 reactor electric power generation for desigh operating conditions with 700 full power days period of steady-state fuel cycle was calculated. The suggested technique enables to reveal the deviation of the real fuel cycling conditions from the standard ones and calculate the value of this deviation, establish the reasons, disturbing the economical conditions of reactor operation, to approximate the real conditions of fuel cycling to the optimal ones by influencing on technological process, resulting in the change of factors, determining the fuel cycling efficiency during electric power generation and refueling in considered cycle

Results of trial operation of the WWER advanced fuel assemblies

International Nuclear Information System (INIS)

Vasilchenko, I.; Dragunov, Y.; Mikhalchuk, A.

2001-01-01

The paper describes results from experimental operation of advanced WWER-1000 fuel assemblies (AFA) at five units in Balakovo NPP. Advanced fuel is developed according to the concept of standard WWER-1000 fuel assembly (jacket-free). The new features includes: 1) zirconium guiding channels (alloy E-635 and E-110) and spacer grids (alloy E-110); 2) integrated burnable absorber gadolinium; 3) extended service life of fuel assemblies (FA) and absorber rods (possibility of repair of FA); 4) improved adoption to reactor conditions. Some results of AFA pilot operation of a three year operation are presented and analyses of effectiveness of improvements are made concerning application of zirconium channels and grids; application of integrated burnable absorbers; extension of FA and absorbing rods service life and FA repairability. These new features of WWER-1000 fuel design allow: 1) to reduce the average fuel enrichment to the 3.77% instead of 4.31% in U-235; 2) to reduce the FA axial load in reactor hot state by 40%,; 3) increasing of fuel operation in reactor to the 30000 effective days with possibility to have a 5-year residence time in the reactor. The design of new generation FA for WWER-440 reactors involves few key changes. Fuel inventory in new fuel design is increased due to elongation of fuel stack and reducing the diameter of the central hole. Vibration stability is enhanced as a result of: no-play junction of the fuel rod with the lower grid; change of SG arrangements; strengthening of the lower grid unit; secure of the central tube in the gap. Water-uranium ration is increased. Introduction of all these kinds of modernization in a 5-year fuel cycle reduces fuel component in the energy cost to the 7%

Control of WWER-440 nuclear reactor

International Nuclear Information System (INIS)

Wagner, K.; Drab, F.; Grof, V.

1978-01-01

The V-1 reactor control systems are described. The data acquisition and processing system fulfils four main functions, ie., reactor start-up and power increase to 10% of the rated power, automatic power control within 3% and 110% of the rated power, reactivity compensation, and reactor protection. The automatic control system ensures constant steam pressure maintained with an accuracy of +-0.05 MPa. Reactivity compensation and spatial power distribution is mainly safeguarded by boric acid control. The V-1 reactor protection system has four levels of accident protection depending on the gravity of the failure. The philosophy of automation of the V-1 reactor control and protection system is based on autonomous automatic controlers and on the direct control of the individual sets and technological equipment. In conclusion, development trends are briefly outlined of control and protection systems of light water reactor power plants. (Z.M.)

Thermophysical instruments for non-destructive examination of tightness and internal gas pressure or irradiated power reactor fuel rods

International Nuclear Information System (INIS)

Pastoushin, V.V.; Novikov, A.Yu.; Bibilashvili, Yu.K.

1998-01-01

The developed thermophysical method and technical instruments for non-destructive leak-tightness and gas pressure inspection inside irradiated power reactor fuel rods and FAs under poolside and hot cell conditions are described. The method of gas pressure measuring based on the examination of parameters of thermal convection that aroused in gas volume of rod plenum by special technical instruments. The developed method and technique allows accurate value determination of not only one of the main critical rod parameters, namely total internal gas pressure, that forms rod mean life in the reactor core, but also the partial pressure of every main constituent of gaseous mixture inside irradiated fuel rod, that provides the feasibility of authentic and reliable leak-tightness detection. The described techniques were experimentally checked during the examination of all types power reactor fuel rods existing in Russia (WWER, BN, RBMK) and could form the basis for new technique development for non-destructive examination of PWR (and other) type rods and FAs having gas plenum filled with spring or another elements of design. (author)

Systems for noise diagnostics of WWER nuclear power plants

International Nuclear Information System (INIS)

Por, G.

1996-01-01

The aim of this paper is to give a short overview of the noise diagnostics system developed by Hungarian firms which are in operation in WWER type NPP Units. Giving a list of systems developed for noise diagnostics of WWER reactors we present their main characteristics, their goal and some of their achievements. The second part deals with the problem of acceptance of noise system by NPP and regulations. (author). 24 refs

Systems for noise diagnostics of WWER nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Por, G [Technical Univ. of Budapest, Budapest (Hungary)

1997-12-31

The aim of this paper is to give a short overview of the noise diagnostics system developed by Hungarian firms which are in operation in WWER type NPP Units. Giving a list of systems developed for noise diagnostics of WWER reactors we present their main characteristics, their goal and some of their achievements. The second part deals with the problem of acceptance of noise system by NPP and regulations. (author). 24 refs.

Fracture mechanics characterisation of the WWER-440 reactor pressure vessel beltline welding seam of Greifswald unit 8

International Nuclear Information System (INIS)

Viehrig, Hans-Werner; Schuhknecht, Jan

2008-01-01

WWER-440 second generation (V-213) reactor pressure vessels (RPV) were produced by IZHORA in Russia and by SKODA in the former Czechoslovakia. The surveillance Charpy-V and fracture mechanics SE(B) specimens of both producers have different orientations. The main difference is the crack extension direction which is through the RPV thickness and circumferential for ISHORA and SKODA RPV, respectively. In particular for the investigation of weld metal from multilayer submerged welding seams the crack extension direction is of importance. Depending on the crack extension direction in the specimen there are different welding beads or a uniform structure along the crack front. The specimen orientation becomes more important when the fracture toughness of the weld metal is directly determined on surveillance specimens according to the Master Curve (MC) approach as standardised in the ASTM Standard Test Method E1921. This approach was applied on weld metal of the RPV beltline welding seam of Greifswald Unit 8 RPV. Charpy size SE(B) specimens from 13 locations equally spaced over the thickness of the welding seam were tested. The specimens are in TL and TS orientation. The fracture toughness values measured on the SE(B) specimens with both orientations follow the course of the MC. Nearly all values lie within the fracture toughness curves for 5% and 95% fracture probability. There is a strong variation of the reference temperature T 0 though the thickness of the welding seam, which can be explained with structural differences. The scatter is more pronounced for the TS SE(B) specimens. It can be shown that specimens with TS and TL orientation in the welding seam have a differentiating and integrating behaviour, respectively. The statistical assumptions behind the MC approach are valid for both specimen orientations even if the structure is not uniform along the crack front. By comparison crack extension, JR, curves measured on SE(B) specimens with TL and TS orientation show

Probabilistic safety assessment of WWER440 reactors prediction, quantification and management of the risk

CERN Document Server

Kovacs, Zoltan

2014-01-01

The aim of this book is to summarize probabilistic safety assessment (PSA) of nuclear power plants with WWER440 reactors and  demonstrate that the plants are safe enough for producing energy even in light of the Fukushima accident. The book examines level 1 and 2 full power, low power and shutdown PSA, and summarizes the author's experience gained during the last 35 years in this area. It provides useful examples taken from PSA training courses the author has lectured and organized by the International Atomic Energy Agency. Such training courses were organised in Argonne National Laboratory (

Power distribution gradients in WWER type cores and fuel failure root causes

Energy Technology Data Exchange (ETDEWEB)

Mikuš, Ján M., E-mail: JanMikus.nrc@hotmail.com

2014-02-15

Highlights: • Power (fission rate) distribution gradients can represent fuel failure root causes. • Positions with above gradients were investigated in WWER type cores on reactor LR-0. • Above gradients were evaluated near core heterogeneities and construction materials. • Results can be used for code validation and fuel failure occurrence investigation. - Abstract: Neutron flux non-uniformity and gradients of neutron current resulting in corresponding power (fission rate) distribution changes can represent root causes of the fuel failure. Such situation can be expected in vicinity of some core heterogeneities and construction materials. Since needed data cannot be obtained from nuclear power plant (NPP), results of some benchmark type experiments performed on light water, zero-power research reactor LR-0 were used for investigation of the above phenomenon. Attention was focused on determination of the spatial power distribution changes in fuel assemblies (FAs): Containing fuel rods (FRs) with Gd burnable absorber in WWER-440 and WWER-1000 type cores, Neighboring the core blanket and dummy steel assembly simulators on the periphery of the WWER-440 standard and low leakage type cores, resp., Neighboring baffle in WWER-1000 type cores, and Neighboring control rod (CR) in WWER-440 type cores, namely (a) power peak in axial power distribution in periphery FRs of the adjacent FAs near the area between CR fuel part and butt joint to the CR absorbing part and (b) decrease in radial power distribution in FRs near CR absorbing part. An overview of relevant experimental results from reactor LR-0 and some information concerning leaking FAs on NPP Temelín are presented. Obtained data can be used for code validation and subsequently for the fuel failure occurrence investigation.

Program of assessment of mechanical and corrosion mechanical properties of reactor internals materials due to operation conditions in WWERs

International Nuclear Information System (INIS)

Ruscak, M.; Zamboch, M.

1998-01-01

Reactor internals are subject to three principle operation influences: neutron and gamma irradiation, mechanical stresses, both static and dynamic, and coolant chemistry. Several cases of damage have been reported in previous years in both boiling and pressure water reactors. They are linked with the term of irradiation assisted stress corrosion cracking as a possible damage mechanism. In WWERs, the principal material used for reactor internals is austenitic titanium stabilized stainless steel 08Kh18N10T, however high strength steels are used as well. To assess the changes of mechanical properties and to determine whether sensitivity to intergranular cracking can be increased by high neutron fluences, the experimental program has been started. The goal is to assure safe operation of the internals as well as life management for all planned operation period. The program consists of tests of material properties, both mechanical and corrosion-mechanical. Detailed neutron fluxes calculation as well as stress and deformation calculations are part of the assessment. Model of change will be proposed in order to plan inspections of the facility. In situ measurements of internals will be used to monitor exact status of structure during operation. Tensile specimens manufactured from both base metal and model weld joint have been irradiated to the total fluences of 3-20 dpa. Changes of mechanical properties are tested by the tensile test, stress corrosion cracking tests are performed in the autoclave with water loop and active loading. Operation temperature, pressure and water chemistry are chosen for the tests. (author)

Report of the experts' mission to review thermal hydraulic and structural analyses for PTS assessment of Kozloduy NPP units 1-4 reactor pressure vessels, Sofia, Bulgaria 3-7 April 1995

International Nuclear Information System (INIS)

1995-01-01

Based upon a request of the Government of Bulgaria and in order to assist its Regulatory Body, an experts' mission was carried out to Sofia and Kozloduy, 21-25 November 1994 within the framework of the IAEA TC Project BUL/9/013-05 and of the IAEA Extrabudgetary Programme on the Safety of the WWER NPPs. The mission also specified the technical content of further assistance by the IAEA. With respect to the findings and recommendations made in November 1994, WWER-SC-109, a follow-up expert's mission was carried out to Sofia, Bulgaria, April 3-7, 1995. The objective of the mission was to review the selection of transients, thermal hydraulic, stress and fracture mechanics analyses for reactor pressure vessel integrity assessment of Kozloduy unit 1-4. In addition, an update on the activities completed, underway and planned related to unit 1 reactor pressure vessel embrittlement was presented and discussed. The review was carried out by 4 international experts from Finland, France, Russia and IAEA in co-operation with the Bulgarian regulatory body, plant, Energoproject Sofia and Institute of Metals staff. The mission was conducted out within the frame of the IAEA TC Project BUL/9/013-05 and of the IAEA Extrabudgetary Programme on the Safety of the WWER NPPs. 18 refs

Calculational-experimental examination and ensuring of equipment and pipelines seismic resistance at starting and operating water-cooled and moderated reactor WWER-type NPPs shake table investigation at Paks NPP. Final report from 15 June 1993 - 15 June 1994

International Nuclear Information System (INIS)

Kaznovsky, S.

1995-01-01

This final report involves the calculation and experimental examination and ensuring the seismic resistance of the reactor equipment and pipelines at start up and operation of WWER type nuclear power plants. Shake table experiments performed at the Paks NPP are included. Namely the following devices of the emergency cooling system were tested: pump of low pressure; valve of low pressure; intermediate heat exchanger. The following values were determined: natural frequencies and vibration decrements and the main modes of normal vibrations for the heat exchanger

VUJE's experience in the field of thermal-hydraulic behaviour of WWER

International Nuclear Information System (INIS)

Klepach, J.

1995-01-01

The thermal-hydraulic behavior (THB) of NPP coolant system and its consequences to nuclear safety of WWER reactors in previous Czechoslovakia has been studied in the VUJE (Nuclear Power Plants Research Institute, Trnava, SK). The institute takes part in the development and verification of its own (SLAP, LENKA, PUMKO, SICHTA, TRACO etc.) and international (DYNAMIKA5) codes for thermal-hydraulic analysis. The verification efforts are concentrated on the WWER specific features such as horizontal steam generators, control and safety system functioning, etc. The whole range of NPP accident analyses is covered by the VUJe staff. The author outlined briefly the WWER specific features as design and implemented improvements in Bohunice V-1 and Mochovce V-1 (WWER 230 model). The pros and cons of the WWER design compared against western type PWR are described. It is believed that although the WWERs are designed under the rules and standards of 1960s, their safety and operational performance can be improved to acceptable level by thorough analysis and appropriate measures. 5 figs

Evaluation of radiation exposures to personnel during maintenance operations and fuel recharging at NPP with the WWER-440 reactor

International Nuclear Information System (INIS)

Beskrestnov, N.V.; Vasil'ev, Eh.S.; Kozlov, V.F.; Odinokov, Yu.Yu.; Romanov, V.P.; Tsypin, S.G.

1983-01-01

A unified data acquisition and analysis system is presented. The system is intended to assess radiation exposures to personnel and perform radiation monitoring during periodic maintenance operations sna fuel recharging at NPPs with WWER-440 reactors. The basic principles of developing this system, patterns of danita collection are considered, points of radiation motoring chosen with account of the NPP operating experience are pointed out

Performance of the Westinghouse WWER-1000 fuel design

International Nuclear Information System (INIS)

Hoglund, J.; Riznychenko, O.; Latorre, R.; Lashevych, P.

2011-01-01

In 2005 six (6) Westinghouse WWER-1000 Lead Test Assemblies (LTAs) were loaded in the South Ukraine Unit 3. This design has demonstrated full compatibility with resident fuel designs and all associated fuel handling and reactor components. Operations have further demonstrated adequacy of performance margins and the reliability requirements for multiple cycles of operation. The LTA's have now been discharged after completing the planned four cycles of operation and having reached an average assembly burnup in excess of 43 MWd/kgU. Post Irradiation Examinations were performed after completion of each cycle. The final LTA inspection program at end of Cycle 20 in 2010 yielded satisfactory results on all counts, and it was concluded that the 6 Westinghouse LTA's performed as expected during their operational regimes. Very good performance was demonstrated in the WWER-1000 reactor environment for the Zr-1%Nb as grid material, and ZIRLO fuel cladding and structural components. Control Rod Assemblies drop times and drag forces were all within the accepted values. The LTA program demonstrated that this fuel design is suitable for full core applications. However, the topic of fuel assembly distortion resistance was re-visited and Westinghouse therefore considered operational experience and design features from multiple development programs to enhance the basic Westinghouse WWER-1000 fuel design for Ukrainian reactors. The design now includes features that further mitigate assembly bow while at the same time improving the fuel cycle economy. This paper describes briefly the development of the Westinghouse WWER-1000 fuel design and how test results and operational experiences from multiple sources have been utilized to produce a most suitable fuel design. Early in 2011 a full region of the Westinghouse WWER-1000 design completed another full cycle of operation at South Ukraine Unit 3, all with excellent results. All 42 fuel assemblies were examined for visible damage or non

Analysis of materials in connection with corium melt retention in WWER reactor vessels. Final report for the period 15 October 1995 - 14 October 1996

International Nuclear Information System (INIS)

Efanov, A.D.

1997-02-01

Analysis of the state of severe accident codes being developed in Russia describing processes of corium - reactor pressure vessel interaction during severe accidents showed that at present there is no reliable validated and verified code. This study considered some of the most advanced severe accident codes which include models of heat generating liquid convections and RPV tolerance capacity however the possibility of physico-chemical interactions is not being considered. The final report demonstrates one of the examples for the settlement modelling of processes of reactor core debris cooling and corium pool mirror cooling with the use of the KOSTER 2 Code developed at IPPE. It was shown that cooling by water spray within some definite region of drop dimensions (0.5 / 4 mm in diameter) could provide the opportunity of the WWER type RPV integrity preservation under the accepted conditions. Due to some uncertainties in calculation modules obtained results are recommended to be treated as preliminary. (author). 26 refs, figs, tabs

An investigation of axial xenon stability in WWER-1000 reactor designs

International Nuclear Information System (INIS)

Doshi, P.K.; Miller, R.W.

1993-01-01

The nuclear power plants of the WWER-1000 design have experienced frequent xenon oscillation control problems. In most PWRs, xenon oscillations are largely a problem in the axial direction. An one dimensional core model representative of the WWER-1000 design was set up to examine the controllability of the current design. An investigation of possible improvements to this design was made. There was no indication that xenon oscillations were an inherent problem in WWER-1000 core design. Simple changes to the control rod system coupled with a sound power distribution control strategy that has been proven to be an effective but simple procedure to follow, eliminate xenon control problems. The changes proposed can be implemented in a very cost effective manner. There are no equipment changes needed, existing control rods can be used. Only software changes are required. (Z.S.) 1 tab., 2 figs., 7 refs

Seismic resistance of WWER equipment (systematization and generalization)

International Nuclear Information System (INIS)

Kaznovski, S.; Chechenov, H.

1999-01-01

Within the scope of the contract with IAEA, calculational and experimental investigations of equipment seismic resistance were carried out. Systematic seismic inspection was conducted for 21 WWER type reactors in Armenia, Bulgaria, Russia, Slovakia and Ukraine. On the base of generalisation of extensive real data accumulated during inspection of equipment seismic resistance at different WWER-type NPPs the classification of seismic instability reasons and working out of generalised recommendations were carried out. It gives the possibility to specialists in many cases to expose the seismic insufficiency of equipment and to choose the suitable measures without laborious experimental investigations, tests, and calculations

Determination and elimination of the reasons for increased control rod insertion time of the Kozloduy NPP WWER-1000

International Nuclear Information System (INIS)

Nikolov, K.

1996-01-01

The emergency insertion speed of the control rod upon reactor shutdown is of crucial importance for reactor safety. The designed insertion time for WWER-1000 reactors should be in the limits 1,5 to 4 s. Having in mind some data about increased insertion times of WWER-1000 type reactors in Russia and Ukraine, a practice of measuring this parameters during each planned outage of the Kozloduy NPP Unit 6 is introduced. Some technical improvements of the fuel assembly are made in order to reach the nominal parameters of the unit

Analysis of expediency to set regulators of high-pressure emergency core cooling system of WWER 1000 (B-320)

International Nuclear Information System (INIS)

Skalozubov, V.I.; Komarov, Yu.A.; Tikhonova, G.G.; Nikiforov, S.N.; Bogodist, V.V.; Fol'tov, I.M.; Khadzh Faradzhallakh Dabbakh, A.

2011-01-01

The work shows that setting regulative valves in high-pressure emergency core cooling system of WWER 1000/B-320 can be effective only involving the additional tuning to account traverse speed of operating elements of regulator and configuration of the systems providing cooling of primary loop.

Assessment of nuclear data needs for broad-group SCALE library related to WWER spent fuel applications

International Nuclear Information System (INIS)

Zalesky, K.; Markova, L.

1999-12-01

A preliminary study aimed at the issue of feasibility to generate a broad-group SCALE library related to WWER spent fuel applications was made. The SCALE code system has been installed and is being used in many countries operating WWER-type reactors for criticality and shielding analyses as well as spent fuel isotopic inventory calculations but still without an extensive validation and verification for the WWER environment. This study should be a contribution to QA connected with the SCALE code system application for the WWER calculations as a basis on which the generation of the specific WWER SCALE library can be prepared. Possible ways of the broad-group library development are described. (author)

Expert system GIP-WWER for verification of seismic adequacy of WWER equipment

International Nuclear Information System (INIS)

Masopust, R.

1999-01-01

The aim of this report is to describe the modified Generic Implementation Procedure (GIP) titled GIP-WWER which can be used to verify seismic adequacy of the safe shutdown mechanical and electrical equipment and distribution systems of operating or constructed WWER NPPs, namely WWER-440/213 type. The WWER-GIP procedure was prepared using available information contained in GIP and the experience taken from various seismic inspections and evaluations of WWER type NPPs performed in the last five years

WWER-1000 steam generator integrity. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1997-07-01

Programme was initiated by IAEA in 1990 with the aim to assist the countries of Central and Eastern Europe and former Soviet Union in evaluating the safety of their first generation WWER-440/230 nuclear power plants. The main objectives were: to identify major design and operational safety issues; to establish international consensus on priorities for safety improvements; and to provide assistance in the review of the competence and and adequacy of safety improvement programs. The scope was extended in 1992 ro include RBMK, WWER-440/312 and WWER-1000 plants in operation and under construction. Based on the operational experience of more than 90 reactor years of WWER-1000 NPPs having 80 steam generators in operation or under construction the steam generator integrity was recognized as an important issue of high safety concern. The purpose of this report is to integrate available information on the issue of WWER-1000 steam generator integrity with the focus on the steam generator cold collector damage in particular. This information covers the status of stem generators at operating plants, cause analysis of collector cracking, the damage mechanisms involved, operational aspects and corrective measures developed and implemented. Consideration is given to material, design and fabrication related aspects, operational conditions, system solutions, and in-service inspection. Detailed conclusions and recommendations are provided for each of these aspects

Status and prospects of activities on algorithms and methods in WWER-1000 core control

International Nuclear Information System (INIS)

Filimonov, P.; Krainov, Y.; Proselkov, V.

1994-01-01

On the basis of long-term operational experience and investigations the problems of WWER-1000 reactor control are discussed. Such control is needed for WWER-1000, as well as for its Western analog PWR, for suppressing the axially instable power density field resulted from non-equilibrium redistribution of Xe-135 nuclei in the reactor core. It has been found that an adequate assessment of the reactor state and the prediction of its response to various control actions is essential for the control of power density distribution. For this purpose a computerized operator's adviser with a reactor simulator realizing a physical reactor model based on BIPR-7 code is used. The operation experience of WWER-1000 shows that the available control algorithms allow, with a fair degree of assurance, the prevention of intensive xenon oscillations and the stabilization of the axial offset. But in connection with the renunciation of half-length control rods a new algorithm is under development which makes use of full-length control rods for suppressing the intensive xenon oscillations in the descending phase. A new method based on BIPR-7 and PERMAK codes is also being developed for estimating the value and rate of linear power rating change of the fuel elements in power cycling. 12 figs., 7 refs

Status and prospects of activities on algorithms and methods in WWER-1000 core control

Energy Technology Data Exchange (ETDEWEB)

Filimonov, P; Krainov, Y; Proselkov, V [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)

1994-12-31

On the basis of long-term operational experience and investigations the problems of WWER-1000 reactor control are discussed. Such control is needed for WWER-1000, as well as for its Western analog PWR, for suppressing the axially instable power density field resulted from non-equilibrium redistribution of Xe-135 nuclei in the reactor core. It has been found that an adequate assessment of the reactor state and the prediction of its response to various control actions is essential for the control of power density distribution. For this purpose a computerized operator`s adviser with a reactor simulator realizing a physical reactor model based on BIPR-7 code is used. The operation experience of WWER-1000 shows that the available control algorithms allow, with a fair degree of assurance, the prevention of intensive xenon oscillations and the stabilization of the axial offset. But in connection with the renunciation of half-length control rods a new algorithm is under development which makes use of full-length control rods for suppressing the intensive xenon oscillations in the descending phase. A new method based on BIPR-7 and PERMAK codes is also being developed for estimating the value and rate of linear power rating change of the fuel elements in power cycling. 12 figs., 7 refs.

WWER fuel: Results of post irradiation examination

International Nuclear Information System (INIS)

Markov, D.V.; Smirnov, V.P.; Smirnov, A.V.; Polenok, V.S.; Perepelkin, S.O.; Ivashchenko, A.A.

2006-01-01

Experience in the field of fabrication, operation, testing and post-irradiation examinations (PIE) made it possible to settle the following requirements for a new generation of WWER nuclear fuel: - For WWER-1000 FA, the service life is no less than 5 years, 3 alternative fuel cycles (FC): 12 months x 4 FCs, 12 months x 5 FCs and 18 months x 3 FCs; - For WWER-440 FA, fuel cycle is 12 months x 5 FCs and a part of operating assembly is left for the 6. year; - High fuel burnup - up to 70 MWd/kgU; - Dimensional stability of FA and its components; - FA repairability; - Adaptability of fuel cycles; - Maintenance of maneuvering operating conditions at the NPP; - Reliability of control rod operation; - High serviceability level - FE leakage is no worse than 10-5 l/year. In order to provide the fulfillment of the above-given requirements, designers and production engineers have worked out cumulative measures and engineering solutions, which are introduced in development of a new generation fuel. Currently old design FA-M assemblies provided with steel skeleton are being operated in WWER-1000 reactors at Ukrainian and Bulgarian NPPs. As for Russian NPPs, new-type FAs are operated. These are advanced FAs (AFA), FA-A and FA-2 provided with zirconium alloy skeletons. A design of the second generation of WWER-440 operating assemblies was developed with respect to changes in some geometrical parameters, fastening of FEs in the lower grid (splinting was substituted for collet), usage of reinforcing rib under the lower grid, anti-debris filter and hafnium elements of junction unit as well as hafnium content decrease from 0.05 % mass down to 0.01% mass in zirconium materials. They are basic designs of FAs in order to be introduced in a five-year fuel cycle of WWER-440 NPPs in Czech Republic and Slovakia since 2005 and have got prospects for development. The operating experience of dismountable operating assemblies at the Loviisa NPP, vibration-proof operating assemblies at the

Progress in Investigation of WWER-440 Reactor Pressure Vessel Steel by Gamma and Moessbauer Spectroscopy

International Nuclear Information System (INIS)

Hascik, J.; Slugen, V.; Lipka, J.; Hinca, R.; Toth, I.; Groene, R.; Uvacik, P.; Kupca, L.

1998-01-01

Gamma spectroscopic analyse and first experimental results of original irradiated reactor pressure vessel surveillance specimens are discussed in. In 1994, the new ''Extended Surveillance Specimen Program for nuclear Reactor Material Study'' was started in collaboration with the nuclear power plants (NPP) V-2 Bohunice (Slovakia). The first batch of MS samples (after 1 year, which is equivalent to 5 years of loading RPV-steel) was measured and interpreted using the new four components approach with the aim to observe microstructural changes due to thermal and neutron treatment resulting from operating conditions in NPP. The systematic changes in the relative areas of Moessbauer spectra components were observed. (author)

Burnup credit implementation in WWER spent fuel management systems: Status and future aspects

International Nuclear Information System (INIS)

Manolova, M.

1998-01-01

This paper describes the motivation for possible burnup credit implementation in WWER spent fuel management systems in Bulgaria. The activities being done are described, namely: the development and verification of a 3D few-group diffusion burnup model; the application of the KORIGEN code for evaluation of WWER fuel nuclear inventory during reactor core lifetime and after spent fuel discharge; using the SCALE modular system (PC Version 4.1) for criticality safety analyses of spent fuel storage facilities. Future plans involving such important tasks as validation and verification of computer systems and libraries for WWER burnup credit analysis are shown. (author)

Thermohydraulic model of WWER-1000 core

International Nuclear Information System (INIS)

Maroti, L.; Szabados, L.

1987-11-01

Safe and economic operation of the WWER-1000 type reactor requires more accurate calculation of the thermohydraulic processes than the one satisfactory for the 440 type cores. The high degree of accuracy is needed both for reactor physics calculations and for the determination of the operational safety limits of the core. The paper illustrates the most important differences between the 1000 and 440 type reactors and presents the main fields of the development work necessary to reach the required accuracy. A prediction for the capability of the computer programs after the proposed development is also given and some suggestions for the further improvement is outlined. (author) 7 refs

Development of codes for physical calculations of WWER

International Nuclear Information System (INIS)

Novikov, A.N.

2000-01-01

A package of codes for physical calculations of WWER reactors, used at the RRC 'Kurchatov Institute' is discussed including the purpose of these codes, approximations used, degree of data verification, possibilities of automation of calculations and presentation of results, trends of further development of the codes. (Authors)

AER working group D on WWER safety analysis - report of the 2007 meeting

International Nuclear Information System (INIS)

Kliem, S.

2007-01-01

The AER working group D on WWER reactor safety analysis held its sixteenth meeting in Paris, France during the period 08-09 May 2007. The meeting was hosted by the CEA France. It followed the final workshop on the OECD/DOE/CEA WWER-1000 Coolant Transient Benchmark held at 07 May. Altogether 11 participants attend the meeting of the working group D, 7 from AER member organizations and 4 guests from non-member organizations. The co-ordinator of the working group, Mr. S. Kliem, served as chairman of the meeting. The meeting started with a general information exchange about the recent activities in the participating organizations. The given presentations and the discussions can be attributed to the following topics: -Code development and benchmarking for reactor dynamics applications; -Safety analysis methodology and results; -Future activities. New solutions for three different benchmarks were presented and discussed. These are the Second AER Dynamic Benchmark on control rod ejection at hot zero power (S. Kliem, FZD), the WWER-1000 Coolant Transient Benchmark (E. Syrjaelahti, VTT) and the stationary AER-FCM101 Benchmark considering a WWER-1000 reactor (C. Parisi, UniPisa). A. Kereszturi (AEKI) presented a statistical evaluation of the possibility to observe a fuel assembly mis loading event. The second presentation of E. Syrjaelahti was dedicated to the description how best-estimate coupled code calculations at VTT are supported by uncertainty and sensitivity analyses. K. Velkov (GRS) presented preliminary results of BIPR8KN/ATHLET calculations with a very detailed resolution of the calculation grid on the assessment of coolant mixing inside WWER-1000 assembly heads. Coolant mixing experiments at three different mixing test facilities, modeling different reactor types, were presented and compared by S. Kliem. A calculation study using the coupled code system KORSAR/GP on the consequences of the injection of a slug of un borated water into the reactor core was

Improvement of operation efficiency for WWER-440 and WWER-1000 for TRIGON fuel assembly design features

Energy Technology Data Exchange (ETDEWEB)

Silberstein, A [European WWER Fuels GmbH, Lyon (France)

1994-12-31

TRIGON 440 and TRIGON 1000 fuel assemblies and their assembly matching counterparts are described. Their role in increasing the efficiency of WWER reactors is stressed. Special attention is paid to their design features as well as calibrated means of predicting behaviour under irradiation from light water reactor core operation. They reduce the fuel cycle cost as a result of the reduced need for natural uranium which have to be enriched and of the smaller number of fuel assemblies which have to be fabricated, stored or reprocessed. The improved control assemblies bring comfort to the plant operator due to intrinsic progress in safety with respect to accidental situation, trouble-free behaviour and long time utilization in the reactor. 14 figs.

Risk based definition of TS requirements for NPPs with WWER-1000 type reactor

International Nuclear Information System (INIS)

Morozov, V.; Tokmachev, G.

2000-01-01

The main regulations in safety related maintenance for NPPs in Russia are defined as a part of Technical Specifications (TSs). It includes limiting conditions for operation (surveillance requirements, allowed outage time, et.). In Russian practice the two levels of TSs are presented: general TSs that have been established as a master documents for similar designed NPPs and plant specific based on operation practice of each NPP unit. This paper presents a brief review of submissions to TS changes for NPPs with WWER type reactor were issued by AEP PSA team since 1988 year. Besides it provides an approach allows to estimate the complex affect on plant risk for both Limiting Conditions of Operation (LCO) and Surveillance Test Intervals (STI) based on relevant probabilistic tool (Minimal Cut Sets method and Marcov Chains methods). (author)

Report of a consultants meeting on control rod insertion reliability for WWER-1000 nuclear power plants. Extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

1995-09-01

Starting from 1992, an increased drop time of control rods exceeding the design limit of four seconds has been observed in most of the operating WWER-1000 reactors in Russia and in the Ukraine. In some cases a dropped control rod became stuck in an intermediate position near the bottom of the core. In October 1994, a similar control rod problem was also observed at Unit 6 of the Kozloduy NPP. The issue of control rod insertion reliability was considered at a consultants' meeting on ''Core Control and Protection Strategy of WWER-1000 Reactors'' in April 1994. A consultants' meeting specifically focused on ''Control Rod Insertion Reliability'' was convened in Vienna in February 1995 attended by 15 international experts. The objectives of this meeting were: The exchange of international experience on problems and solutions related to anomalous control rod insertion; judgement of the safety concern of this issue for WWER-1000 reactors based on safety analyses; consideration of regulatory requirements and interim measures to continue operation in short term including modifications implemented or planned; and, status of root cause analyses and pending problems. The technical discussions were held in plenary sessions and in three working groups devoted to specific aspects of the issue. Refs, figs, tabs

'Kazmer' a complex noise diagnostic system for 1000 MWe PWR WWER type nuclear power units

International Nuclear Information System (INIS)

Por, G.

1992-06-01

Noise diagnostic systems have previously been developed and installed for the WWER-440 type reactors at the Paks Nuclear Power Plant, Hungary. Based on the experiences, the system has been extended and modified for use in 1000 MWe, WWER-1000 type units. KAZMER consists of three subsystem, the KARD reactor noise diagnostic system, ARGUS vibration monitoring system for rotation machinery, and ALMOS acoustic monitoring system. The installation of the KAZMER system at the Kalinin Nuclear Power Station, Russia, and the first operational experiences are outlined. (R.P.) 15 refs.; 9 figs

Temperature and velocity field of coolant at inlet to WWER-440 core - evaluation of experimental data

International Nuclear Information System (INIS)

Jirous, F.; Klik, F.; Janeba, B.; Daliba, J.; Delis, J.

1989-01-01

Experimentally determined were coolant temperature and velocity fields at the inlet of the WWER-440 reactor core. The accuracy estimate is presented of temperature measurements and the relation is given for determining the resulting measurement error. An estimate is also made of the accuracy of solution of the system of equations for determining coefficients B kn using the method of the least square fit. Coefficients B kn represent the relative contribution of the mass flow of the k-th fuel assembly from the n-th loop and allow the calculation of coolant temperatures at the inlet of the k-th fuel assembly, when coolant temperatures in loops at reactor inlet are known. A comparison is made of the results of measurements on a hydrodynamic model of a WWER-440 reactor with results of measurements made at unit 4 of the Dukovany nuclear power plant. Full agreement was found for 32 model measurements and 6 reactor measurements. It may be assumed that the results of other model measurements obtained for other operating variants will also apply for an actual reactor. Their applicability may, however, only be confirmed by repeating the experiment on other WWER-440 reactors. (Z.M.). 5 figs., 7 refs

Behavior of antimony isotopes in the primary coolant of WWER-1000-type nuclear reactors in NPP Kozloduy during operation and shutdown

International Nuclear Information System (INIS)

Dobrevski, Ivan D.; Zaharieva, Neli N.; Minkova, Katia F.; Gerchev, Nikolay B.

2009-01-01

This paper focuses on the behavior of the antimony isotopes 122 Sb and 124 Sb in the coolant of the WWER reactors in the nuclear power plant Kozloduy (Bulgaria) during operation and shutdown. It is concluded that the chemical properties of their actual precursor, the isotope 121 Sb, determine the behavior of 122 Sb and 124 Sb during operation, load fluctuations, and shutdown as well as during the reactor coolant purification process. It is supposed that differences between the reactor bulk and the core fuel cladding surface chemistry as well as the presence of sub-cooled nucleate boiling at the fuel cladding may create conditions under which a local oxidizing environment may come into existence. (orig.)

Experimental research on safety assurance of advanced WWER fuel cycles

International Nuclear Information System (INIS)

Krainov, Ju.; Kukushkin, Ju.

2002-01-01

The paper presents the results of experimental investigations on substantiation of implementation of a modernized butt joint for the WWER-440 reactor, carried out in the critical test facility 'P' in the RRC 'Kurchatov Institute'. The comparison results of the calculation and experimental data obtained in the physical startup of Volgodonsk NPP-1 with the WWER-1000 are also given. In the implementation of four-year fuel cycle in the WWER-440 with the average enrichment of fuel makeup 3.82% it was solved to conduct experimental research of power distribution in the vicinity of control rod butt junction. Moreover, it was assumed that adequate actions should be applied to eliminate inadmissible power jumps, if necessary. It is not available to measure their values in NPP conditions. Therefore, the power distribution near the butt joint was studied in a 19-rod bank installed in the critical test facility 'P' first for the normal design of the joint when surrounding fuel assemblies enrichment goes up. Then a set of calculation and tests was fulfilled to optimize a butt junction design. On the base of this research the composition of a butt junction was advanced by placing Hf plates into the junction. The effectiveness of modernized butt joint design was experimentally confirmed. In Volgodonsk NPP-1 with WWER-1000 the four-year fuel cycle is being implemented. During the physical startup of the reactor the measurements of the reactivity effects and coefficients were measured at the minimum controlled flux level, and the parameters of a number of critical states were recorded. The data obtained were compared with the calculation. The validity of the certified code package for forecasting the neutronic characteristics of WWER-1000 cores in the implementation of a four year fuel cycle has been supported (Authors)

Characterisation of the inventory of radioisotopes induced in the biological shield a WWER-440 reactor

International Nuclear Information System (INIS)

Feher, S.; Czifrus, Sz.; Zsolnay, E.M.; Szondi, E.

2001-01-01

A significant part of the radwaste originating from the decommissioning of NPPs is made up of the activated concrete and steel components of the biological shield. The paper presents the results of studies aimed at the determination of the amount of radionuclides accumulating in the serpentinous and ordinary concrete shield around the WWER-440 reactors of the Paks NPP. For the calculations, the reactor, vessel and shield were modelled in detail both in terms of geometry and material composition. The spatial and energy distribution of the activating neutron spectrum was determined by certain modules of SCALE 4.3 and the code TORT in two and three dimensions, while the activation was calculated using ORIGEN-S for 22 geometrical regions. The results showed that the activity of the concrete structures at final shutdown after 30 years of operation is approximately 50 TBq, which decreases to 20, 12, 1.1 TBq and 27 GBq after 1 month, 1 year, 10 and 100 years, respectively (Authors)

Power peak in vicinity of WWER-440 control rod at end of fuel cycle

International Nuclear Information System (INIS)

Mikus, J.

2003-01-01

This paper presents some results of the axial power distribution measurements carried out in a WWER-440 type core on the light-water, zero-power reactor LR-O in the vicinity of the WWER-440 control rod model at zero boron concentration in moderator. Further presented information concern the description of the control rod model, LR-0 core arrangement, specification of the fuel assemblies and measurement conditions. The aim of performed experiment is enlargement of the available 'power peaking database' to enable the calculation codes validation also by means of data that correspond to the end of WWER-440 fuel cycle (Authors)

Nuclear safety improvement activities related to WWER-440 units in Bulgaria

International Nuclear Information System (INIS)

Gantchev, T.

1998-01-01

The systematic evaluation of the deficiencies of the original design of the WWER reactors brought to the development of a Short Term Programme for Safety Upgrading and Modernisation of Kozloduy WWER-440 units. The implementation of this Programme was completed in 1997. The strive for continuos improvement of Kozloduy Nuclear Power Plant (NPP) safety level, the new requirements of the Bulgarian Nuclear Safety Authority and the public concern initiated the development of new Complex Programme for Safety Improvement (PRG'97), now in a process of implementation. (author)

Ranking of safety issues for WWER-440 model 230 nuclear power plants

International Nuclear Information System (INIS)

1992-02-01

In response to requests from Member States operating Soviet designed WWER-440/230 nuclear power plants (NPPs) for assistance through the IAEA's nuclear safety services, a major international project was established to evaluate these first generation reactors as a complement to relevant ongoing national, bilateral and multilateral activities. The objective is to assist countries operating WWER-440/230 NPPs in performing comprehensive safety reviews aimed at identifying design and operational weaknesses. The scope of the project includes a review of the conceptual design of WWER-440/230 NPPs, safety review missions to each one of the operating reactors to review design and operational aspects and studies to resolve issues of generic safety concern. This report was prepared by a group of international experts and the IAEA staff and discussed by the Project Steering Committee, December 9-13, 1991 in Vienna. An overview of the safety issues identified is presented indicating their effect on the performance of the basic safety functions. Conceptual recommendations related to design issues are given as a technical basis for the safety modifications required

Verification of the transuranus-WWER code version V1M2J00 by SOFIT and Kola-3 data bases: Part 2

International Nuclear Information System (INIS)

Elenkov, D.; Boneva, S.; Djourelov, N.

2002-01-01

The object of this study is standard WWER-440 fuel as described in the IFPE-OECD/IAEA-NEA database. The SOFIT and Kola-3 data base have been used the purpose, each one described in a separate paper, referred to as Part I (concerning SOFIT) and Part II (concerning Kola-3). It has been shown that the latest modifications of the programme lead to considerable improvements of the predictions on the fuel behaviour. Concerning the TRANSURANUS-WWER code calculations of different fuel behaviour characteristics of Kola-3 standard fuel rods, the following conclusions can be made: the burnup calculations are in excellent agreement with the measured values; the fission gas release calculations accounting for the high burnup structure influence are in very good agreement with the experiment for the two assemblies in the burnup region up to 40 MWd/kgU; the size changes for the cladding are reproduced in fairly good way; the gas pressure is reproduced by some 10 -15 % underestimation. From the obtained results including the discussed deviations, the present version of TRANSURANUS-WWER can be considered as applicable for the modelling fuel performance in Bulgarian nuclear power plants operating WWER reactors

Investigation of WWER fuel behaviour under MIR power ramps

International Nuclear Information System (INIS)

Bibilashvili, Yu.K.; Novikov, V.V.; Agafonov, S.N.

1996-01-01

The paper discusses results of experimental WWER fuel investigation under power ramps. Specificity of using the research reactor ''MIR'' to accomplish scheduled power rating of fuel is considered. The paper presents the methodology of experiments using irradiation facility ''TEST''. Reactor experiments were performed at burn-up ∼ 10000 MW.day/t UO 2 using standard fuel pins and the ones having backfitted fuel and cladding. (author). 7 figs, 1 tab

Development of a new WWER-440 fuel design

International Nuclear Information System (INIS)

Coucil, D.; Totev, T.

1998-01-01

In March 1996 British Nuclear Fuel Limited signed a contract with Imatran Voima and Paks Nuclear Power Plant to design, develop, license and supply 5 Lead Test Assemblies to the WWER-440 reactor at Loviisa in Finland. In June 1998 the manufacture of these 5 assemblies (4 fixed assemblies and 1 follower assembly) was completed. The fuel is expected to be loaded into Loviisa Unit 2 reactor during the shutdown scheduled for September of this year. (Authors)

Dynamic behavior structural response and capacity evaluation of the standardized WWER-1000 nuclear power plants subjected to severe loading conditions

International Nuclear Information System (INIS)

Ambriashvili, Y.K.; Krutzik, N.J.

1993-01-01

In order to verify the structural capacity of standardized WWER-1000 MW nuclear power plants, comprehensive static and dynamic analyses were performed in cooperation between Siemens and Atomenergoprojekt. The main goal of these investigations was to perform of a number of seismic analyses of standardized WWER-1000 reactor buildings on the basis of 13 given seismological inputs, taking into account the local soil conditions at 17 different sites defined by in-situ investigations. The analyses were based on appropriate mathematical models (equivalent beam models as well as detailed spatial surface element models) of the coupled vibrating structures (base structure, outer structure, containment, inner structure) and of the layered soil. The analyses were mainly performed using the indirect method (substructure method). Based on the results of the seismic analysis as well as the results of static analysis (pressure and temperature due to LOCA, dead weight, prestressing) an assessment was made of the seismic safety of the containment and the reactor building. Using a complex 3-dimensional model of the structure and the soil, the influence of the flexibility of the basement structure on the structural response was also studied. The structural analyses of the WWER-1000 reactor building led to the conclusion that its design accounts well for the main factors governing the dynamic behavior of the building. The assessment of the forces acting in the structures shows that the bearing capacity of the analyzed building structure corresponds to an earthquake intensity of about 0.2 g to 0.25 g

Analysis of differences in fuel safety criteria for WWER and western PWR nuclear power plants

International Nuclear Information System (INIS)

2003-11-01

In 2001 the OECD issued a report of the NEA/CSNI (Committee on the Safety of Nuclear Installations) Task Force on the existing safety criteria for reactor fuel for western LWR nuclear power plants (both for PWRs and BWRs) under new design elements. Likewise in 2001, the IAEA released a report by a Working Group on the existing safety criteria for reactor fuel for WWER nuclear power plants under new design requirements. However, it was found that it was not possible to compare the two sets of criteria on the basis upon which they had been established. Therefore, the IAEA initiated an assessment of the common features and differences in fuel safety criteria between plants of eastern and western design, focusing on western PWRs and eastern WWER reactors. Between October 2000 and November 2001, the IAEA organized several workshops with representatives from eastern and western European countries in which the current fuel safety related criteria for PWR and WWER reactors were reviewed and compared. The workshops brought together expert representatives from the Russian Federation, from the Ukraine and from western countries that operate PWRs. The first workshop focused on a general overview of the fuel safety criteria in order for all representatives to appreciate the various criteria and their respective bases. The second workshop (which involved one western and one eastern expert) concentrated on addressing and explaining the differences observed, and documenting all these results in preparation for a panel discussion. This panel discussion took place during the third workshop, where the previously obtained results were reviewed in detail and final recommendations were made. This report documents the findings of the workshops. It highlights the common features and differences between PWR and WWER fuel, and may serve as a general basis for the safety evaluation of these fuels. Therefore, it will be very beneficial for licensing activities for PWR and WWER plants, as it

In core-fuel management in approach to equilibrium of WWER-440 reactor; Prelazni rezim iskoriscenja goriva u nuklearnom reaktoru tipa VVER-440

Energy Technology Data Exchange (ETDEWEB)

Marinkovic, N [Boris Kidric Institute of nuclear sciences, Vinca, Belgrade (Yugoslavia)

1978-07-01

For the need of in core fuel management and prediction of fuel cycle costs as well as operating of a nuclear power plant behaviour of main physical parameters and refueling scheme during approach to equilibrium operation are indispensable. An estimation of a refueling scheme during forst six years of exploitation for a commercially proven PWR reactor of WWER-440 type is shown in this paper. (author)

Upgrading of seismic capacity of WWER equipment including reactor control rods and distribution systems

International Nuclear Information System (INIS)

Kostarev, V.

1993-01-01

This paper concerns the experience of CKTI VIBROSEISM firm (CVS) in seismic capacity upgrading of the WWER equipment and pipings. During the last 15 years CVS has accumulated a lot of experimental and analysis results on many of WWER units 'in former Soviet Union. That might be very useful in seismic protecting of East European Nuclear Power Plants. (author)

WWER-440 reactor thermal power increase. Up-to-date approaches to substantiation of the core heat-engineering reliability

International Nuclear Information System (INIS)

Vasilchenko, I.; Lushin, V.; Zubtsov, D.

2006-01-01

Increasing the Units power is an urgent problem for nuclear power plants with WWER-440 reactors. Improving the fuel assembly designs and calculated codes creates all prerequisites to fulfil this purpose. The decrease in the core power peaking is reached by using the profiled fuel assemblies, burnable absorber integrated into the fuel, the FA with the modernized interface attachment, modern calculated codes that allows to reduce conservatism of the RP safety substantiation. A wide spectrum of experimental study of behaviour of the fuel having reached burn-up (50-60) MW days / kg U under the transients and accident conditions was carried out, the post-irradiated examination of the fuel assemblies, fuel rods and fuel pellets with four and five annual operating fuel cycle were performed as well and confirmed the high reliability of the fuel, the presence of large margins of the fuel stack state that contributes to reactor operation at the increased power. The results of the carried out experiments on implementing the five and six annual fuel cycles show that the limiting fuel state as to its serviceability in the WWER-440 reactors is far from being reached. Presently there is an experience of the increased power operation of Kola NPP, Units 1, 2, 4 and Rovno NPP, Unit 2. The Loviisa NPP Units are operated at 109 % power. The Russian experts had gained an experience in substantiating the core operation at 108 % power for Paks NPP, Unit 4. In this paper the additional conditions for increasing the power of the Kola NPP, Units 1 and 2 and the main results of substantiation of increase in power of the Paks NPP, Unit 4 up to 1485 MW are presented in details

Assessment of the influence of design limits to the economics of WWER fuel cycle

International Nuclear Information System (INIS)

Dementiev, V.G.; Shishkov, L.K.

2010-01-01

The paper discusses the influence of the reactor parameters limits for normal operation on the economical performance of WWER fuel cycles. It is shown for the typical WWER fuel cycles that decreasing the limits for the main power distribution parameters to 10% leads to decreasing the fuel components of the electricity cost price up to 4-5%. As the nowadays limitations are reached the dependence becomes weaker. (Authors)

Partially closed fuel cycle of WWER-440

International Nuclear Information System (INIS)

Darilek, P.; Sebian, V.; Necas, V.

2002-01-01

Position of nuclear energy at the energy sources competition is characterised briefly. Multi-tier transmutation system is outlined out as effective back-end solution and consequently as factor that can increase nuclear energy competitiveness. LWR and equivalent WWER are suggested as a first tier reactors. Partially closed fuel cycle with combined fuel assemblies is briefed. Main back-end effects are characterised (Authors)

The decommissioning of WWER type nuclear power plants. Final report on an IAEA regional technical co-operation project

International Nuclear Information System (INIS)

2000-01-01

Numerous WWER-440 nuclear power plants are in operation in central and eastern Europe and a small number have already been shut down. In addition to reactors already shut down, many other reactors will reach the end of their design lifetime in a few years and become candidates for decommissioning. It is unfortunate that little consideration was devoted to decommissioning of WWER-440 reactors at the plant design and construction stage, and little emphasis was placed on planning for decommissioning. It is within this context that the IAEA launched a regional technical co-operation project in 1994 with the aim of providing guidance on planning and management of decommissioning for WWERs. The project, which had a duration of four years (1995-1998), included the organization of workshops and scientific visits to countries having WWERs and other countries where active decommissioning projects were under way. Eventually, participants suggested the consolidation of expert guidance and collective opinions into a TECDOC, which was drafted by both designated participants from project recipient countries and invited experts. The TECDOC has the aim of serving as a stimulus for all concerned parties in central and eastern European countries to initiate concrete decommissioning planning, including assessment of existing and required resources for the eventual implementation of decommissioning plans. In addition, the regional technical co-operation project has managed to bring together in this TECDOC a number of good practices that could be useful in WWER-440 decommissioning

Status and trends in nuclear technology for power plants with WWER-1000 reactors. Review

Energy Technology Data Exchange (ETDEWEB)

Zorev, N N

1977-04-01

The problems of improving quality of nuclear equipment for WWER-1000 power plants and associated nuclear technology automation are surveyed. Examples of technological innovations are presented which significantly reduce labour intensity, time consumption and increase quality standards of the products. Some new automated equipments for materials welding, working, machining and quality control are described. The discussion is centering around heavy-section steel technologies. Some mechanical properties of new-developed nuclear grade steels designed for producing reactor vessels and steamgenerators, volume compensators and pipes, as well as steam separators and steamsuperheaters are also presented. Their properties (impact strength and radiation resistance) are pointed out to be superior to that of steels used abroad. The basic trend in nuclear structural material developments is towards integrated optimization of strength, performance and workability.

A small angle neutron study of irradiation induced microstructures in Cr-Mo-V WWER steels

International Nuclear Information System (INIS)

Levit, Vladimir I.; Santos, Ari S.; Louzada, Ana R.R.; Silveira, Cristina M.; Vaniel, Ana Paula H.; Odette, George R.; Mader, Eric

2000-01-01

Small angle neutron scattering (SANS) has proven to be a very effective technique for characterizing the ultrafine (∼1 nm) irradiation induced microstructures which are responsible for hardening and the concomitant embrittlement of reactor pressure vessel steels. SANS measurement were carried out on three irradiated and unirradiated weld materials of WWER- type on 8 m instrument at the National Institute of Standards and Technology, Washington, USA. Small (r m < 1 nm) irradiation induced features were found for all three materials. Were found volume fractions, number densities and ratios of magnetic to nuclear scattering. Some analyses of the irradiation induced precipitation nature and possible chemical composition were made by comparison of the results with other reactor materials SANS and Atom Probe Field Ion Microscopy data. (author)

Experience in start-up of the South-Ukrainian-2 power unit with the WWER-1000 reactor

International Nuclear Information System (INIS)

Belov, Yu.V.; Kazakov, V.A.; Kirilov, V.V.; Kryakvin, L.V.

1987-01-01

The volume, sequence and dates of works fulfilled during hot testing, physical and power start-ups and while bringing output of the South-Ukranian-2 power unit with the WWER-1000 reactor to the design figure are described. The works were fulfilled according to the standard schedules from October in 1984 till April in 1985. Combination of the stages and intensification of works before the physical start-up have allowed to shorten the dates by 90 days as compared to the schedule. The physical and power start-ups, including bringing reactor output to the design figure, were performed during 140 days, that permits to shorten the dates by 20 days more. The results of physical experiments carried out at the South-Ukranian-2 power unit, are in good agreement with the data obtained at the first power units of the given and Kalinin NPPs. Besides, during physical and power start-ups additional measures ensuring nuclear safety are developed

Experimental investigation of power peak in vicinity of WWER-440 control rod at end of fuel cycle

International Nuclear Information System (INIS)

Mikus, J.

2004-01-01

This paper presents some results of the axial power (fission density) distribution measurements carried out on the light-water, zero-power reactor LR-0 in a WWER-440 type core in vicinity of the WWER-440 control rod model at zero boron concentration in moderator, modelling the conditions at the end of the WWER-440 fuel cycle. Further information concerns the control rod model description, specification of the LR-0 core, fuel assemblies and measurement conditions. The aim of performed experiment is enlargement of the available power peaking database to enable the validation of the calculation codes by means of the measured data that correspond to the end of WWER-440 fuel cycle. (author)

Contributions to the determination of the thermal core reliability of pressurized water reactors

International Nuclear Information System (INIS)

Ackermann, G.; Horche, W.; Melchior, H.; Prasser, H.M.

1982-09-01

The investigations in the field of thermohydraulics of PW reactors are aimed at a possible increase of economy and reliability of WWER-type-reactors. In detail the flow distribution at the core entrance, the modification of the power distribution as a result of an irregular temperature distribution at the core entrance, and based on the theory of hot spots the thermic core reliability are studied. In this connection qualitatively new methods are applied characterized by low expenditure. (author)

Subcriticality determination of nuclear reactor

International Nuclear Information System (INIS)

Borisenko, V.I.; Goranchuk, V.V.; Sidoruk, N.M.; Volokh, A.F.

2014-01-01

In this article the subcriticality determination of nuclear reactor is considered. Emphasized that, despite the requirements of regulatory documents on the subcriticality determination of WWER from the beginning of their operation, so far, this problem has not been solved. The results of subcriticality determination of Rossi-α method of the WWER-M is presented. The possibility of subcriticality determination of WWER is considered. The possibility of subcriticality determination of Rossi-α method with time resolution is of about 100 microseconds is also considered. The possible reasons for the error in subcriticality determination of the reactor are indicated

The behaviour of WWER nuclear power stations under abnormal operational conditions

International Nuclear Information System (INIS)

Ackermann, G.; Dreger, P.; Prasser, H.M.; Reichenbach, D.

1985-01-01

The big power WWER type reactors can show the volumetric oscillations of the power density into the reactor core because of xenon poisoning. The ununiform xenon distribution occurs in the case of nonideal mixing of the coolant into the reactor vessel. This effect usually leads to decreasing of the reactor power. The theoretical and experimental investigations with the goal to evaluate the volumetric distribution of the temperature near the coolant input into the reactor core is discussed in this paper as well as the three dimensional model of the reactor core together with the primary coolant circuit model to calculate volumetric xenon oscillations

Pressure tube reactor

International Nuclear Information System (INIS)

Seki, Osamu; Kumasaka, Katsuyuki.

1988-01-01

Purpose: To remove the heat of reactor core using a great amount of moderators at the periphery of the reactor core as coolants. Constitution: Heat of a reactor core is removed by disposing a spontaneous recycling cooling device for cooling moderators in a moderator tank, without using additional power driven equipments. That is, a spontaneous recycling cooling device for cooling the moderators in the moderator tank is disposed. Further, the gap between the inner wall of a pressure tube guide pipe disposed through the vertical direction of a moderator tank and the outer wall of a pressure tube inserted through the guide pipe is made smaller than the rupture distortion caused by the thermal expansion upon overheating of the pressure tube and greater than the minimum gap required for heat shiels between the pressure tube and the pressure tube guide pipe during usual operation. In this way, even if such an accident as can not using a coolant cooling device comprising power driven equipment should occur in the pressure tube type reactor, the rise in the temperature of the reactor core can be retarded to obtain a margin with time. (Kamimura, M.)

Implementation of safety parameter display system on Russian NPPs with WWER reactors

International Nuclear Information System (INIS)

Dounaev, V.G.; Neboyan, V.T.

1996-01-01

This report gives a short overview of the status of safety parameter display systems (SPDS) implementation on Russian NPPs with WWER reactors and also discusses the SPDS, which is being developed for Kalinin NPP. The assessment of the safety status of the plant is done by the continuous monitoring of six critical safety functions and the corresponding status trees. Besides, a number of additional functions are realized within the scope of KlnNPP, aimed at providing the operator and the safety engineer in the main control room with more detailed information in accidental situation as well as during the normal operation. In particular, these functions are: archiving, data logs and alarm handling, safety actions monitoring, mnemonic diagrams indicating the state of main technological equipment and basic plant parameters, reference data, etc. Also, the operator support function ''computerized procedures'' is included in the scope of SPDS. The basic SPDS implementation platform is ADACS of SEMA GROUP design. The system architecture includes two workstations in the main control room: one is for reactor operator and the other one for safety engineer. Every station has two CRT screens which ensures computerized procedures implementation and provides for extra services for the operator. Also, the information from the SPDS is transmitted to the local crisis centre and to the crisis centre of the State utility organization concern ''Rosenergoatom''. (author). 3 refs

Express diagnostics of WWER fuel rods at nuclear power plants

International Nuclear Information System (INIS)

Pavlov, S.; Amosov, S.; Sagalov, S.; Kostyuchenko, A.

2009-01-01

Higher safety and economical efficiency of nuclear power plants (NPP) call for a continuous design modification and technological development of fuel assemblies and fuel rods as well as optimization of their operating conditions. In doing so the efficiency of new fuel introduction depends on the completeness of irradiated fuel data in many respects as well as on the rapidity and cost of such data obtaining. Standard examination techniques of fuel assemblies (FA) and fuel rods (FR) intended for their use in hot cell conditions do not satisfy these requirements in full extent because fuel assemblies require preliminary cooling at NPP to provide their shipment to the research center. Expenditures for FA transportation, capacity of hot cells and expenditures for the examined fuel handling do not make it possible to obtain important information about the condition of fuel assemblies and fuel rods after their operation. In order to increase the comprehensiveness of primary data on fuel assemblies and fuel rods immediately after their removal from the reactor, inspection test facilities are widely used for these purposes. The inspection test facilities make it possible to perform nondestructive inspection of fuel in the NPP cooling pools. Moreover these test facilities can be used to repair failed fuel assemblies. The ultrasonic testing of failed fuel rods inside the fuel assembly was developed for stands of inspection and repair of TVSA WWER-1000 for the Kalinin NPP and Temelin NPP. This method was tested for eight leaking fuel assemblies WWER-440 and WWER-1000 with a burnup of ∼14 up to 38 MW·day/kgU. The ultrasonic testing proved its high degree of reliability and efficiency. The defectoscopy by means of the pulsed eddy-current method was adapted for the stand of inspection and repair of TVSA WWER-1000 for the Kalinin NPP. This method has been used at RIAR as an express testing method of FR claddings during the post-irradiation examinations of fuel assemblies WWER

The integration of fast reactor to the fuel cycle in Slovakia

International Nuclear Information System (INIS)

Zajac, R.; Darilek, P.; Necas, V.

2009-01-01

A very topical problem of nuclear power is the fuel cycle back-end. One of the options is a LWR spent fuel reprocessing and a fissile nuclides re-use in the fast reactor. A large amount of spent fuel has been stored in the power plant intermediate storage during the operation of WWER-440 reactors in Slovakia. This paper is based on an analysis of Pu and minor actinides content in actual WWER-440 spent fuel stored in Slovakia. The next part presents the possibilities of reprocessing and Pu re-use in fast reactor under Slovak conditions. The fuel cycle consisting of the WWER-440 reactor, PUREX reprocessing plant and a sodium fast reactor was designed. The last section compares two parts of this fuel cycle: one is UOX cycle in WWER-440 reactor and the other is cycle in the fast reactor - SUPER PHENIX loaded with MOX fuel (Pu + Minor Actinides). The starting point is a single recycling of Pu from WWER-440 in the fission products. The next step is multi recycling of Pu in the fission products to obtain equilibrium cycle. This article is dealing with the solution of power production and fuel cycle indicators. All kinds of calculations were performed by computer code HELIOS 1.10. (Authors)

Pressure tube type reactors

International Nuclear Information System (INIS)

Komada, Masaoki.

1981-01-01

Purpose: To increase the safety of pressure tube type reactors by providing an additional ECCS system to an ordinary ECCS system and injecting heavy water in the reactor core tank into pressure tubes upon fractures of the tubes. Constitution: Upon fractures of pressure tubes, reduction of the pressure in the fractured tubes to the atmospheric pressure in confirmed and the electromagnetic valve is operated to completely isolate the pressure tubes from the fractured portion. Then, the heavy water in the reactor core tank flows into and spontaneously recycles through the pressure tubes to cool the fuels in the tube to prevent their meltdown. By additionally providing the separate ECCS system to the ordinary ECCS system, fuels can be cooled upon loss of coolant accidents to improve the safety of the reactors. (Moriyama, K.)

Verification results of methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants

International Nuclear Information System (INIS)

Saunin, Yuri V.; Dobrotvorski, Alexander N.; Semenikhin, Alexander V.; Korolev, Alexander S.

2017-01-01

The JSC ''Atomtechenergo'' experts have developed a new methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants. The necessity for developing the new methodology was determined by the need to decrease the calculation error of the weighted mean coolant temperature in the hot legs because of the coolant temperature stratification. The methodology development was based on the findings of experimental and calculating research executed by the authors. The methodology verification was fulfilled through comparison of calculation results obtained with and without the methodology use in various operational states and modes of several WWER-1000 power units. The obtained verification results have confirmed that the use of the new methodology provides objective error decrease in determining the weighted mean coolant temperature in the primary circuit hot legs. The decrease value depends on the stratification character which is various for different objects and conditions.

Verification results of methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants

Energy Technology Data Exchange (ETDEWEB)

Saunin, Yuri V.; Dobrotvorski, Alexander N.; Semenikhin, Alexander V.; Korolev, Alexander S. [JSC ' ' Atomtechenergo' ' , Novovoronezh (Russian Federation). Novovoronezh Filial ' ' Novovoronezhatomtechenergo' ' ; Ryasny, Sergei I. [JSC ' ' Atomtechenergo' ' , Moscow (Russian Federation)

2017-09-15

The JSC ''Atomtechenergo'' experts have developed a new methodology for determining the weighted mean coolant temperature in the primary circuit hot legs of WWER-1000 reactor plants. The necessity for developing the new methodology was determined by the need to decrease the calculation error of the weighted mean coolant temperature in the hot legs because of the coolant temperature stratification. The methodology development was based on the findings of experimental and calculating research executed by the authors. The methodology verification was fulfilled through comparison of calculation results obtained with and without the methodology use in various operational states and modes of several WWER-1000 power units. The obtained verification results have confirmed that the use of the new methodology provides objective error decrease in determining the weighted mean coolant temperature in the primary circuit hot legs. The decrease value depends on the stratification character which is various for different objects and conditions.

WWER-1000 fuel cycles: current situation and outlook

International Nuclear Information System (INIS)

Kosourov, E.; Pavlov, V.; Pavlovichev, A.; Spirkin, E.; Shcherenko, A.

2013-01-01

Usage mode of nuclear fuel in WWER type reactor has been changed significantly till the moment of the first WWER-1000 commissioning. There are a lot of improvements, having an impact on the fuel cycle, have been implemented for units with WWER-1000. FA design and its constructional materials, FA fuel weight, burnable poison, usage mode of units and etc have been modified. As the result of development it has been designed a modern FA with rigid skeleton. As a whole it allows to use more efficient configurations of the core, to extend range of fuel cycle lengths and to provide good flexibility in the operation. In recent years there were in progress works on increasing FA uranium capacity. As the result there were developed two designs of the fuel rod: 1) the fuel column height of 3680 mm, diameters of the fuel pellet and its central hole of 7.6 and 1.2 mm respectively and 2) the fuel column height of 3530 mm, the fuel pellet diameter of 7.8 mm without the central hole. Such fuel rods have operating experience as a part of different FA designs. Positive operating experience was a base of new FA (TVS-4) development with the fuel column height of 3680 mm and the fuel pellet diameter of 7.8 mm without the central hole. The paper presents the overview of WWER-1000, AES-2006 and WWER-TOI fuel cycles based on FAs with fuel rod designs described above. There are demonstrated fuel cycle possibilities and its technical and economic characteristics. There are discussed problems of further fuel cycle improvements (fuel enrichment increase above 5 %, use of erbium as alternative burnable poison) and their impact on neutronics characteristics. (authors)

Some consideration on reviewing of WWER

Energy Technology Data Exchange (ETDEWEB)

Shibata, Heki [Yokohama National University, Mechanical Engineering and Material Sciences, Tokiwadai, Hodogaya, Yokohama (Japan)

1993-07-01

The main points of NPP safety are to prevent core melt-down and to mitigate the divergence of radioactive materials to the atmosphere in general. However, destroying of the reactor building may cause damages of various mechanical and other components and piping systems, and these failures may proceed to LOCA and other critical failures of safety related items. The main items that are considered in view of upgrading the existing WWER type reactors are: buildings, emergency power supply systems, anchoring devices and concrete structures, mechanical components, water storage, piping support, civil engineering structure. This pipe describes the method for improving seismic capacity of the operating NPPs and to keep their safety under seismic conditions.

Some consideration on reviewing of WWER

International Nuclear Information System (INIS)

Shibata, Heki

1993-01-01

The main points of NPP safety are to prevent core melt-down and to mitigate the divergence of radioactive materials to the atmosphere in general. However, destroying of the reactor building may cause damages of various mechanical and other components and piping systems, and these failures may proceed to LOCA and other critical failures of safety related items. The main items that are considered in view of upgrading the existing WWER type reactors are: buildings, emergency power supply systems, anchoring devices and concrete structures, mechanical components, water storage, piping support, civil engineering structure. This pipe describes the method for improving seismic capacity of the operating NPPs and to keep their safety under seismic conditions

Solution of the 'MIDICORE' WWER-1000 core periphery power distribution benchmark by KARATE and MCNP

International Nuclear Information System (INIS)

Temesvari, E.; Hegyi, G.; Hordosy, G.; Maraczy, C.

2011-01-01

The 'MIDICORE' WWER-1000 core periphery power distribution benchmark was proposed by Mr. Mikolas on the twentieth Symposium of AER in Finland in 2010. This MIDICORE benchmark is a two-dimensional calculation benchmark based on the WWER-1000 reactor core cold state geometry with taking into account the geometry of explicit radial reflector. The main task of the benchmark is to test the pin by pin power distribution in selected fuel assemblies at the periphery of the WWER-1000 core. In this paper we present our results (k eff , integral fission power) calculated by MCNP and the KARATE code system in KFKI-AEKI and the comparison to the preliminary reference Monte Carlo calculation results made by NRI, Rez. (Authors)

Reactor vessel pressure transient protection for pressurized water reactors

International Nuclear Information System (INIS)

Zech, G.

1978-09-01

During the past few years the NRC has been studying the issue of protection of the reactor pressure vessels at Pressurized Water Reactors (PWRs) from transients when the vessels are at a relatively low temperature. This effort was prompted by concerns related to the safety margins available to vessel damage as a result of such events. Nuclear Reactor Regulation Category A Technical Activity No. A-26 was established to set forth the NRC plan for resolution of the generic aspects of this safety issue. The purpose of the report is to document the completion of this generic technical activity

Problems of WWER-440 dynamic changes

International Nuclear Information System (INIS)

Rydzi, S.

1986-01-01

The data processing capability of the DYNAMIKA program is presented and demonstrated for the calculation of coolant parameters and heat transfer variables of the WWER reactor in accident and transient modes of operation. An experimental outage is described of the TG 11 turbogenerator at the V-1 Jaslovske Bohunice nuclear power plant. The measured values were compared with values calculated using the DYNAMIKA program. The graphic representation makes it evident that the mathematical model comes very close to reality. (J.B.)

Contribution to the WWER-440 Gd-assembly evolution

International Nuclear Information System (INIS)

Cudrnak, P.; Darilek, P.; Necas, V.

2009-01-01

Development activities, presented in the paper, contribute to the evolution of gadolinium fuel for the WWER-440 reactors. Short overview of existing and already proposed Gd-assemblies is given. Two new assembly types with improved features are described. Multiplication coefficients and pin power peaking factors of all mentioned gadolinium assemblies are compared. Animations of power distribution behaviour in selected Gd-assemblies are shown. (Authors)

Mathematical modelling and quality indices optimization of automatic control systems of reactor facility

International Nuclear Information System (INIS)

Severin, V.P.

2007-01-01

The mathematical modeling of automatic control systems of reactor facility WWER-1000 with various regulator types is considered. The linear and nonlinear models of neutron power control systems of nuclear reactor WWER-1000 with various group numbers of delayed neutrons are designed. The results of optimization of direct quality indexes of neutron power control systems of nuclear reactor WWER-1000 are designed. The identification and optimization of level control systems with various regulator types of steam generator are executed

Experience in WWER fuel assemblies vibration analysis

International Nuclear Information System (INIS)

Ovtcharov, O.; Pavelko, V.; Usanov, A.; Arkadov, G.; Dolgov, A.; Molchanov, V.

2003-01-01

It is stated that the vibration studies of internals and the fuel assemblies should be conducted during the reactor designing, commissioning and commercial operation stages and the analysis methods being used should complement each other. The present paper describes the methods and main results of the vibration noise studies of internals and the fuel assemblies of the operating NPPs with WWER reactors, as an example of the implementation of the comprehensive approach to the analysis on equipment flow-induced vibration. At that, the characteristics of internals and fuel assemblies vibration loading were dealt jointly as they are elements of the same compound oscillating system and their vibrations have the interrelated nature

Structural and leakage integrity assessment of WWER steam generator tubes

International Nuclear Information System (INIS)

Splichal, K.; Otruba, J.; Keilova, E.; Krhounek, V.; Turek, J.

1996-01-01

The leakage and plugging limits were derived for WWER steam generators based on leak and burst tests using tubes with axial part-through and through-wall defects. The following conclusions were arrived at: (i) The permissible primary-to-secondary leak rate with respect to the permissible through-wall defect size of WWER-440 and WWER-1000 steam generator tubes is 8 l/h. (ii) The primary-to-secondary leak rate is reduced by the blocking of the tube cracks by corrosion product particles and other substances. (iii) The rate of crack penetration through the tube wall is higher than the crack widening. (iv) The validity of the criterion of instability for tubes with through-wall cracks was confirmed experimentally. For the WWER-440 and WWER-1000 steam generators, the critical size of axial through-wall cracks, for the threshold primary-to-secondary pressure difference, is 13.8 and 12.0 mm, respectively. (v) The calculated leakage for the rupture of one tube and for the assumed extreme defects is two orders and one order of magnitude, respectively, higher than the proposed primary water leakage limit of 8 l/h. (vi) The experiments gave evidence that the use of the permissible thinning limit of 80% for the heat exchange tube plugging does not bring about uncontrollable leakage or unstable crack growth. This is consistent with experience gained at WWER-440 type nuclear power plants. 4 tabs., 5 figs., 9 refs

Possible pressurized thermal shock events during large primary to secondary leakage. The Hungarian AGNES project and PRISE accident scenarios in VVER-440/V213 type reactor

Energy Technology Data Exchange (ETDEWEB)

Perneczky, L. [KFKI Atomic Energy Research Inst., Budabest (Hungary)

1997-12-31

Nuclear power plants of WWER-440/213-type have several special features. Consequently, the transient behaviour of such a reactor system should be different from the behaviour of the PWRs of western design. The opening of the steam generator (SG) collector cover, as a specific primary to secondary circuit leakage (PRISE) occurring in WWER-type reactors happened first time in Rovno NPP Unit I on January 22, 1982. Similar accident was studied in the framework of IAEA project RER/9/004 in 1987-88 using the RELAP4/mod6 code. The Hungarian AGNES (Advanced General and New Evaluation of Safety) project was performed in the period 1991-94 with the aim to reassess the safety of the Paks NPP using state-of-the-art techniques. The project comprised three type of analyses for the primary to secondary circuit leakages: Design Basis Accident (DBA) analyses, Pressurized Thermal Shock (PTS) study and deterministic analyses for Probabilistic Safety Analysis (PSA). Major part of the thermohydraulic analyses has been performed by the RELAP5/mod2.5/V251 code version with two input models. 32 refs.

Possible pressurized thermal shock events during large primary to secondary leakage. The Hungarian AGNES project and PRISE accident scenarios in VVER-440/V213 type reactor

Energy Technology Data Exchange (ETDEWEB)

Perneczky, L [KFKI Atomic Energy Research Inst., Budabest (Hungary)

1998-12-31

Nuclear power plants of WWER-440/213-type have several special features. Consequently, the transient behaviour of such a reactor system should be different from the behaviour of the PWRs of western design. The opening of the steam generator (SG) collector cover, as a specific primary to secondary circuit leakage (PRISE) occurring in WWER-type reactors happened first time in Rovno NPP Unit I on January 22, 1982. Similar accident was studied in the framework of IAEA project RER/9/004 in 1987-88 using the RELAP4/mod6 code. The Hungarian AGNES (Advanced General and New Evaluation of Safety) project was performed in the period 1991-94 with the aim to reassess the safety of the Paks NPP using state-of-the-art techniques. The project comprised three type of analyses for the primary to secondary circuit leakages: Design Basis Accident (DBA) analyses, Pressurized Thermal Shock (PTS) study and deterministic analyses for Probabilistic Safety Analysis (PSA). Major part of the thermohydraulic analyses has been performed by the RELAP5/mod2.5/V251 code version with two input models. 32 refs.

Development of supercritical water reactors in Russia and abroad

International Nuclear Information System (INIS)

Glebov, A.P.; Klushin, A.V.

2014-01-01

The results of Russian and foreign studies on the water-cooled high critical parameters reactors are analyzed. Developments on this subject are conducted in more than 15 countries. The advantages of WWER- SCP and characteristics of experimental reactor of WWER-SCP-30 are discussed. It is noted that priority task is to develop a reactor with thermal neutron spectrum with a subsequent transition to the reactor with a fast neutron spectrum [ru

National Report of Bulgaria [National practice at WWER sites

International Nuclear Information System (INIS)

2017-01-01

Kozloduy NPP Plc. is located in north-western Bulgaria at about 3 km from the Danube River, which serves as a source of cooling water and a receiver of liquid released from the plant (Fig. I.3). Six nuclear units were constructed on Kozloduy NPP site. Units 1 to 4 are WWER-440/230 reactors and Units 5 and 6 are WWER-1000/320 reactors. Units 1 to 4 were commissioned from 1974 to 1982. Units 5 and 6 were commissioned in 1987 and 1991, respectively. On December 31, 2002 Units 1 and 2 were shut down and on December 31, 2006 Units 3 and 4 were shut down as well. Spent Nuclear Fuel was removed from the pre-reactor pools and the reactors have been prepared for decommissioning. Units 1 and 2 (in 2008) and Units 3 and 4 (in 2012) were declared as Decommissioning Facilities by Ministerial Decree and outsourced from the plant. A separate complex consisting of facilities for treatment and conditioning of wet and dry solid radioactive waste (RAW) and a facility for storage of conditioned RAW was commissioned in 2001 on site. The complex is situated next to the Auxiliary Building of Units 5 and 6. In 2005 this complex was outsourced as a separate enterprise called the Specialized Enterprise for Radioactive Waste (SE RAW). There are two Spent Fuel Storage Facilities (SFSF) for wet and dry storage located on the plant site as well.

Code package to analyse behavior of the WWER fuel rods in normal operation: TOPRA's code

International Nuclear Information System (INIS)

Scheglov, A.; Proselkov, V.

2001-01-01

This paper briefly describes the code package intended for analysis of WWER fuel rod characteristics. The package includes two computer codes: TOPRA-1 and TOPRA-2 for full-scale fuel rod analyses; MRZ and MKK codes for analyzing the separate sections of fuel rods in r-z and r-j geometry. The TOPRA's codes are developed on the base of PIN-mod2 version and verified against experimental results obtained in MR, MIR and Halden research reactors (in the framework of SOFIT, FGR-2 and FUMEX experimental programs). Comparative analysis of calculation results and results from post-reactor examination of the WWER-440 and WWER-1000 fuel rod are also made as additional verification of these codes. To avoid the enlarging of uncertainties in fuel behavior prediction as a result of simplifying of the fuel geometry, MKK and MRZ codes are developed on the basis of the finite element method with use of the three nodal finite elements. Results obtained in the course of the code verification indicate the possibility for application of the method and TOPRA's code for simplified engineering calculations of WWER fuel rods thermal-physical parameters. An analysis of maximum relative errors for predicting of the fuel rod characteristics in the range of the accepted parameter values is also presented in the paper

Improvements of radioactive waste management at WWER nuclear power plants

International Nuclear Information System (INIS)

2006-04-01

extended consultants meeting held in November 1999. Ten experts from eight Member States representing most of the countries operating power plants with WWER reactors attended this meeting. Additional work was performed at the meeting 3-7 April 2000 by the group of consultants. The initial draft of the second report was prepared by four consultants. The draft was updated 14-18 June 2004 by eleven radioactive waste management experts from nine Member States. Due to their very similar nature and subject matter, the two reports were merged into a single TECDOC in April 2005. The resulting report was finalized in the meeting 5-9 September 2005 by four radioactive waste management experts from Finland, Hungary, Slovakia and USA

Thermohydraulic accident behavior of reactors

International Nuclear Information System (INIS)

Horche, W.; Kirmse, R.; Reichenbach, D.; Weber, J.P.

1992-01-01

GRS, on behalf of the German Federal Ministry for the Environment, conducted an assessment of the technical safety of the Greifswald nuclear generating units of the Soviet WWER-440/W-230 and W-213 reactor lines, respectively. The evaluation of existing accident analyses and the execution of some first calculations by GRS added to the know-how of GRS. This is reflected in the increased participation by GRS in international expert bodies investigating safety problems of WWER-440 plants. The contributions made towards international WWER projects within the framework of IAEA missions or as a result of bilateral consultations strengthen international partnership in the field of reactor safety in Central and Eastern Europe. (orig.) [de

WWER expert system for fuel failure analysis using the RTOP-CA code

International Nuclear Information System (INIS)

Likhanskii, V.; Evdokimov, I.; Sorokin, A.; Khromov, A.; Kanukova, V.; Apollonova, O.; Ugryumov, A.

2008-01-01

The computer expert system for fuel failure analysis of WWER during operation is presented. The diagnostics is based on the measurement of specific activity of reference nuclides in reactor primary coolant and application of a computer code for the data interpretation. The data analysis includes an evaluation of tramp uranium mass in reactor core, detection of failures by iodine and caesium spikes, evaluation of burnup of defective fuel. Evaluation of defective fuel burnup was carried out by applying the relation of caesium nuclides activity in spikes and relations of activities of gaseous fission products for steady state operational conditions. The method of burnup evaluation of defective fuel by use of fission gas activity is presented in details. The neural-network analysis is performed for determination of failed fuel rod number and defect size. Results of the expert system application are illustrated for several fuel campaigns on operating WWER NPPs. (authors)

Local linear heat rate ramps in the WWER-440 transient regimes

International Nuclear Information System (INIS)

Brik, A.N.; Bibilashvili, Ju.L.; Bogatyr, S.M.; Medvedev, A.V.

1998-01-01

The operation of the WWER-440 reactors must be accomplished in such a way that the fuel rods durability would be high enough during the whole operation period. The important factors determining the absence of fuel rod failures are the criteria limiting the core characteristics (fuel rod and fuel assembly power, local linear heat rate, etc.). For the transient and load follow conditions the limitations on the permissible local linear rate ramp are also introduced. This limitation is the result of design limit of stress corrosion cracking of the fuel cladding and depends on the local fuel burn-up. The control rod motion is accompanied by power redistribution, which, in principle, can result in violating the design and operation limitations. Consequently, this motion have to be such as the core parameters, including the local ramps of the linear heat generation rates would not exceed the permissible ones.The paper considers the problem of WWER-440 reactor control under transient and load follow conditions and the associated optimisation of local linear heat generation rate ramps. The main factors affecting the solution of the problem under consideration are discussed. Some recommendations for a more optimal reactor operation are given.(Author)

WWER-440 fuel rod performance analysis with PIN-Micro and TRANSURANUS codes

International Nuclear Information System (INIS)

Vitkova, M.; Manolova, M.; Stefanova, S.; Simeonova, V.; Passage, G.; Lassmann, K.

1994-01-01

PIN-micro and TRANSURANUS codes were used to analyse the WWER-440 fuel rod behaviour at normal operation conditions. Two highest loaded fuel rods of the fuel assemblies irradiated in WWER-440 with different power histories were selected. A set of the most probable average values of all geometrical and technological parameters were used. A comparison between PIN-micro and TRANSURANUS codes was performed using identical input data. The results for inner gas pressure, gap size, local linear heat rate, fuel central temperature and fission gas release as a function of time calculated for the selected fuel rods are presented. The following conclusions were drawn: 1) The PIN-micro code predicts adequately the thermal and mechanical behaviour of the two fuel rods; 2) The comparison of the results obtained by PIN-micro and TRANSURANUS shows a reasonable agreement and the discrepancies could be explained by the lack of thoroughly WWER oriented verification of TRANSURANUS; 3) The advanced TRANSURANUS code could be successfully applied for WWER fuel rod thermal and mechanical analysis after incorporation of all necessary WWER specific material properties and models for the Zr+1%Nb cladding, for the fuel rod as a whole and after validation against WWER experimental and operational data. 1 tab., 10 figs., 10 refs

WWER-440 fuel rod performance analysis with PIN-Micro and TRANSURANUS codes

Energy Technology Data Exchange (ETDEWEB)

Vitkova, M; Manolova, M; Stefanova, S; Simeonova, V; Passage, G [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika; Kharalampieva, Ts [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Lassmann, K [European Atomic Energy Community, Karlsruhe (Germany). European Inst. for Transuranium Elements

1994-12-31

PIN-micro and TRANSURANUS codes were used to analyse the WWER-440 fuel rod behaviour at normal operation conditions. Two highest loaded fuel rods of the fuel assemblies irradiated in WWER-440 with different power histories were selected. A set of the most probable average values of all geometrical and technological parameters were used. A comparison between PIN-micro and TRANSURANUS codes was performed using identical input data. The results for inner gas pressure, gap size, local linear heat rate, fuel central temperature and fission gas release as a function of time calculated for the selected fuel rods are presented. The following conclusions were drawn: (1) The PIN-micro code predicts adequately the thermal and mechanical behaviour of the two fuel rods; (2) The comparison of the results obtained by PIN-micro and TRANSURANUS shows a reasonable agreement and the discrepancies could be explained by the lack of thoroughly WWER oriented verification of TRANSURANUS; (3) The advanced TRANSURANUS code could be successfully applied for WWER fuel rod thermal and mechanical analysis after incorporation of all necessary WWER specific material properties and models for the Zr+1%Nb cladding, for the fuel rod as a whole and after validation against WWER experimental and operational data. 1 tab., 10 figs., 10 refs.

Solution of safety problems for nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Krett, V.; Pernitsa, R.; Pfann, Ya.; Zbeglik, J.

1982-01-01

Institute of nuclear research (INR) of Czechoslovakian Atomic Energy Commission isto fulfil the supervision functions within the field of nuclear power research and development. The problems of safe operation ensurance for the nuclear power plants (NPP) with WWER-440 reactors are studied within the frame of sever major issues: code standardization and devolopment of guiding materials for the state supervision; neutronic and thermohydrolic data processing for the accident analysis; operation reliability studies of the safety systems and estimates of separate component failure importance; assessment of the accidents resulting from the equipment misfunctioning and component failures; development of a controlled reliability program; evaluation of the atomic installationsimpact on the environment; ensurence of the reactor vessel reliability and durability under irradiation. The NPP safety analysis incorporates the calculations of transient and accidental regimes for the core, the primary loop and the entire plant. A number of codes has been produced which allow to determine the state of fuel elements during operation just before the accidents assessed, thermohydrolic conditions in the coolant and the temperature distribution within the fuel both for the stationary reactor conditions and for transient regimes. A mathematical model has been deveoloped, including the description of all the primary loop major components. The Soviet code DYNAMIKA has been adopted and adjusted for EC-1040 computer, there by the accident analysis for the entire NPP has been made possible. On the basis of american SAFTE code a faster SAFEDO-2 code has been developed employing the Monte Carlo method for the accident analysis of a complex system described by means of a failure tree. The discussed codes are used at the data assessment for the accident analysis part of the safety reports as well as for the reliability evaluation of the emergency core cooling system [ru

Applied model of through-wall crack of coolant vessels of WWER-type reactors

International Nuclear Information System (INIS)

Petrosyan, V.; Hovakimyan, T.; Vardanyan, M.; Khachatryan, A.; Minasyan, K.

2010-01-01

We propose an applied-model of Through-Wall Crack (TWC) for WWER-type units primary vessels. The model allows to simulate the main morphological parameters of real TWC, i.e. length, area of inlet and outlet openings, channel depth and small and large size unevenness of the crack surface. The model can be used for developing and improving the coolant-leak detectors for the primary circuit vessels of WWER-units. Also, it can be used for research of the coolant two-phase leakage phenomenon through narrow cracks/channels and thermo-physical processes in heat-insulation layer of the Main Coolant Piping (MCP) during the leak

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4A. Paks NPP: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to seismic analyses of structures of Paks and Kozloduy reactor buildings and WWER-440/213 primary coolant loops with different antiseismic devices

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4A. Paks NPP: Analysis/testing. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on data related to seismic analyses of structures of Paks and Kozloduy reactor buildings and WWER-440/213 primary coolant loops with different antiseismic devices.

[95/95] Approach for design limits analysis in WWER

International Nuclear Information System (INIS)

Shishkov, L.; Tsyganov, S.

2008-01-01

The paper discusses a well-known condition [95%/95%], which is important for monitoring some limits of core parameters in the course of designing the reactors (such as PWR or WWER). The condition ensures the postulate 'there is at least a 95 % probability at a 95 % confidence level that' some parameter does not exceed the limit. Such conditions are stated, for instance, in US standards and IAEA norms as recommendations for DNBR and fuel temperature. A question may arise: why can such approach for the limits be only applied to these parameters, while not normally applied to any other parameters? What is the way to ensure the limits in design practice? Using the general statements of mathematical statistics the authors interpret the [95/95] approach as applied to WWER design limits. (Authors)

Reactor pressure tank

International Nuclear Information System (INIS)

Dorner, H.; Scholz, M.; Jungmann, A.

1975-01-01

In a reactor pressure tank for a nuclear reactor, self-locking hooks engage a steel ring disposed over the removable cover of the steel vessel. The hooks exert force upon the cover to maintain the cover in a closed position during operation of the reactor pressure tank. The force upon the removal cover is partly the result of the increasing temperature and thermal expansion of the steel vessel during operation. The steel vessel is surrounded by a reinforced-concrete tank. (U.S.)

Halden Reactor Project activities, achievements and international collaboration

International Nuclear Information System (INIS)

Wiesenack, W.

2003-01-01

This paper concentrates on the Halden Project research programme related to fuel testing. An overview of ongoing tests on WWER fuel performance is also included. The ongoing and planned experiments containing WWER-related fuels and materials - Irradiation of Standard and Modified WWER Fuel (IFA-503) and Corrosion Testing of Different Cladding Alloys (IFA-638) - are presented. The future experiments involving WWER fuel and cladding types foreseen in of the Halden Reactor Project programme are given

Safety issues and their ranking for 'small series' WWER-1000 nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This report presents the safety issues in 'small series' WWER-1000 nuclear power plants (NPPs). Safety issues are deviations from current recognized safety practices in design and operation judged to be safety significant by their impact on the plants' defence in depth. This report is intended to serve as reference for the development of plant specific safety improvement programmes and for the evaluation of measures proposed and/or implemented. The identification of safety issues is based on safety studies conducted by the operators of 'small series' WWER-1000 units and by organizations dealing with these reactors, on findings of IAEA safety missions to 'small series' WWER-1000 plants in South Ukraine, at Novovoronezh and Kalinin, and on information obtained from specialists from various countries during an IAEA consultants meeting, 8-12 September 1997 in Vienna, within the framework of the Extra budgetary Programme on the Safety of WWER and RBMK NPPs. Safety issues are first presented according to their impact on the main safety functions and are then described individually. The safety issues are characterized by issue title and specified by issue clarification. Safety issues connected with plant design are followed by the ranking of the issue and ranking justification. Altogether 85 safety issues have been identified, 12 of which are in Category III (defence in depth is insufficient, immediate corrective action is necessary), 38 in Category 11 (defence in depth is degraded, action is needed to resolve the issue) and 22 in Category I (departure from international practices, to be addressed as part of actions to resolve higher priority issues). In the case of operational safety issues (13 safety issues) no ranking is provided as the available material was considered insufficient. For each safety issue, comments and recommendations are made by the IAEA; the status of corresponding measures to improve safety implemented or planned at each site are presented in the

Safety issues and their ranking for 'small series' WWER-1000 nuclear power plants. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

International Nuclear Information System (INIS)

2000-09-01

This report presents the safety issues in 'small series' WWER-1000 nuclear power plants (NPPs). Safety issues are deviations from current recognized safety practices in design and operation judged to be safety significant by their impact on the plants' defence in depth. This report is intended to serve as reference for the development of plant specific safety improvement programmes and for the evaluation of measures proposed and/or implemented. The identification of safety issues is based on safety studies conducted by the operators of 'small series' WWER-1000 units and by organizations dealing with these reactors, on findings of IAEA safety missions to 'small series' WWER-1000 plants in South Ukraine, at Novovoronezh and Kalinin, and on information obtained from specialists from various countries during an IAEA consultants meeting, 8-12 September 1997 in Vienna, within the framework of the Extra budgetary Programme on the Safety of WWER and RBMK NPPs. Safety issues are first presented according to their impact on the main safety functions and are then described individually. The safety issues are characterized by issue title and specified by issue clarification. Safety issues connected with plant design are followed by the ranking of the issue and ranking justification. Altogether 85 safety issues have been identified, 12 of which are in Category III (defence in depth is insufficient, immediate corrective action is necessary), 38 in Category 11 (defence in depth is degraded, action is needed to resolve the issue) and 22 in Category I (departure from international practices, to be addressed as part of actions to resolve higher priority issues). In the case of operational safety issues (13 safety issues) no ranking is provided as the available material was considered insufficient. For each safety issue, comments and recommendations are made by the IAEA; the status of corresponding measures to improve safety implemented or planned at each site are presented in the

Physics measurements on WWER-440 diagnostic assemblies

International Nuclear Information System (INIS)

Dach, K.; Jirousek, V.; Kott, J.; Horak, J.; Teren, S.; Nemec, J.

1980-01-01

The aims of physics measurements using diagnostic assemblies are the development of neutron noise diagnostics methods, the improvement of knowledge of the physical properties of the WWER reactor cores, the testing of computer programs, and the specification of nuclear safety criteria and the obtaining of information allowing the optimum nuclear fuel economy. The instrumentation of diagnostic assemblies is briefly described, including miniature fission chambers, SPN detectors and calorimeters. The method of evaluating and experimental testing is shown. (M.S.)

Full-scale model development of the WWER-440 reactor fuel rod bundle for core temperature regime study under reflooding conditions

International Nuclear Information System (INIS)

Bezrukov, Yu.A.; Logvinov, S.A.; Levchuk, S.V.; Nakladnov, V.D.; Onshin, V.P.; Sokolov, A.S.

1982-01-01

Consideration is given to the issues of a full scale WWER-440 fuel rod bundle imitation. An imitator contains a molybdenum heating rod inclosed in stainless steel shell. The shell diameter is 9 mm, the heated length is 2500 mm, the total len.o.th is 2855 mm. 125 fuel rod imitators are set in the bundle mock-up. The experiments were run on a test facility imitating the WWER-440 reactor primary loop, providing the conditions of the loop breaking. The mock-up thermal hydraulics has been studied during the refloodino. stage. The mock-up was heated up to predetermined initial temperature at a low power level with saturated steam cooling. Then the steam input was stopped, the power level rarapidly rised up to a given value and the cooling water injected. Simultaneously with water injection all the measured parameters monitoring was started. Both at the top spraying and combined cooling temperature oscillations in the upper and middle parts of the mock-up were observed. At the bottom reflooding the mock-up cooling down took more time, thereat temperature inthe upper part first slowly rised during reflooding then decreased and then dropped abruptly at thefront coming up [ru

Modal analysis of spent fuel cask for WWER-1000 reactors

International Nuclear Information System (INIS)

Azimfar, S. A.; Kazemi, A.

2011-01-01

The Spent Fuel Assemblies of WWER-1000 reactors are planned to be transported by special containers which are supposed to be designed in a manner to stand against vibrations and impacts in order to protect the spent fuel from any possible damage. The vibration opposition of these containers shall be far beyond the critical resonance, because the resonances about the natural frequency of the structure will cause the enhancement of its oscillation range and may end with its disintegration. Determination of the amounts of natural frequencies and their mode shape can be achieved by vibration analyzing methods. The amount of the natural frequency of any structure crucially depends on its shape, material and lean points as well as the amount of the loads and the type of these loads. Due to the fact that the Spent Fuel Casks used for transportation in nuclear power plants in Russian Federation are TK-13 type and the pieces of information released are negligible, the scientists in Russia are working on the design and analysis of a new type made up of composite Material. In the presented paper the cask of spent fuel of TK-13 is modeled by ANSYS at 10.0 and ten natural frequency modes have been calculated, followed by the comparison of this result with the composite cask.

Pressure tube reactor

International Nuclear Information System (INIS)

Susuki, Akira; Murata, Shigeto; Minato, Akihiko.

1993-01-01

In a pressure tube reactor, a reactor core is constituted by arranging more than two units of a minimum unit combination of a moderator sealing pipe containing a calandria tube having moderators there between and a calandria tube and moderators. The upper header and a lower header of the calandria tank containing moderators are communicated by way of the moderator sealing tube. Further, a gravitationally dropping mechanism is disposed for injecting neutron absorbing liquid to a calandria gas injection portion. A ratio between a moderator volume and a fuel volume is defined as a function of the inner diameter of the moderator sealing tube, the outer diameter of the calandria tube and the diameter of fuel pellets, and has no influence to intervals of a pressure tube lattice. The interval of the pressure tube lattice is enlarged without increasing the size of the pressure tube, to improve production efficiency of the reactor and set a coolant void coefficient more negative, thereby enabling to improve self controllability and safety. Further, the reactor scram can be conducted by injecting neutron absorbing liquid. (N.H.)

Proceedings of the twenty-first symposium of atomic energy research on WWER physics and reactor safety

International Nuclear Information System (INIS)

Vidovszky, I.

2011-10-01

The present volume contains 61 papers, presented on the twenty-first symposium of atomic energy research, held in Dresden, Germany, 19-23 September 2011. The papers are presented in their original form, i. e. no corrections or modifications were carried out. The content of this volume is divided into thematic groups: Improvement, extension and validation of parameterized few-group libraries for WWER-440 and WWER-1000.

Experimental studies of thermo-hydraulic processes during passive safety systems operation in new WWER NPP projects

International Nuclear Information System (INIS)

Morozov, A.V.; Remizov, O.V.; Kalyakin, D.S.

2014-01-01

The results of experimental study of thermal-hydraulic processes during operation of the passive safety systems of WWER reactors of new generation are given. The interaction processes of counter flows of saturated steam and cold water in vertical steam-line of the auxiliary passive core reflood system from secondary hydraulic accumulator are studied. The peculiarities of undeveloped boiling on single horizontal tube heating by steam and steam-gas mixture, which is character for WWER steam generator condensing mode, are investigated [ru

Electromagnetism Mechanism for Enhancing the Refueling Cycle Length of a WWER-1000

Directory of Open Access Journals (Sweden)

Navid Poursalehi

2017-02-01

Full Text Available Increasing the operation cycle length can be an important goal in the fuel reload design of a nuclear reactor core. In this research paper, a new optimization approach, electromagnetism mechanism (EM, is applied to the fuel arrangement design of the Bushehr WWER-1000 core. For this purpose, a neutronic solver has been developed for calculating the required parameters during the reload cycle of the reactor. In this package, two modules have been linked, including PARCS v2.7 and WIMS-5B codes, integrated in a solver for using in the fuel arrangement optimization operation. The first results of the prepared package, along with the cycle for the original pattern of Bushehr WWER-1000, are compared and verified according to the Final Safety Analysis Report and then the results of exploited EM linked with Purdue Advanced Reactor Core Simulator (PARCS and Winfrith Improved Multigroup Scheme (WIMS codes are reported for the loading pattern optimization. Totally, the numerical results of our loading pattern optimization indicate the power of the EM for this problem and also show the effective improvement of desired parameters for the gained semi-optimized core pattern in comparison to the designer scheme.

Electromagnetism mechanism for enhancing the refueling cycle length of a WWER-1000

Energy Technology Data Exchange (ETDEWEB)

Poursalehi, Navid; Nejati-Zadeh, Mostafa; Minuchehr, Abdolhamid [Dept. of Nuclear Engineering, Shahid Beheshti University, Tehran (Iran, Islamic Republic of)

2017-02-15

Increasing the operation cycle length can be an important goal in the fuel reload design of a nuclear reactor core. In this research paper, a new optimization approach, electromagnetism mechanism (EM), is applied to the fuel arrangement design of the Bushehr WWER-1000 core. For this purpose, a neutronic solver has been developed for calculating the required parameters during the reload cycle of the reactor. In this package, two modules have been linked, including PARCS v2.7 and WIMS-5B codes, integrated in a solver for using in the fuel arrangement optimization operation. The first results of the prepared package, along with the cycle for the original pattern of Bushehr WWER-1000, are compared and verified according to the Final Safety Analysis Report and then the results of exploited EM linked with Purdue Advanced Reactor Core Simulator (PARCS) and Winfrith Improved Multigroup Scheme (WIMS) codes are reported for the loading pattern optimization. Totally, the numerical results of our loading pattern optimization indicate the power of the EM for this problem and also show the effective improvement of desired parameters for the gained semi-optimized core pattern in comparison to the designer scheme.

The solution of the LEU and MOX WWER-1000 calculation benchmark with the CARATE - multicell code

International Nuclear Information System (INIS)

Hordosy, G.; Maraczy, Cs.

2000-01-01

Preparations for disposition of weapons grade plutonium in WWER-1000 reactors are in progress. Benchmark: Defined by the Kurchatov Institute (S. Bychkov, M. Kalugin, A. Lazarenko) to assess the applicability of computer codes for weapons grade MOX assembly calculations. Framework: 'Task force on reactor-based plutonium disposition' of OECD Nuclear Energy Agency. (Authors)

The summary of WWER-1000 fuel utilization in Ukraine

Energy Technology Data Exchange (ETDEWEB)

Afanasyev, A [Ukrainian State Committee on Nuclear Power Utilization, Kiev (Ukraine)

1997-12-01

The report discusses the status of the fuel and fuel cycles of WWER-1000 reactors in Ukraine. The major reasons that caused the Ukrainian utilities to overcome the conservative design solutions in order to improve fuel utilization and extend fuel burnup are shown. At the same time the sufficient fuel reliability and fuel cycle flexibility are ensured. The burnup distribution in the unloaded fuel assemblies and average fuel rod failure rate are presented. The questions of reactor core operation safety and the economical problems of the front end of the fuel cycle are also considered. (author). 2 refs, 3 figs, 4 tabs.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4D. Paks NPP: Analysis and testing. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on seismic margin assessment and earthquake experience based methods for WWER-440/213 type NPPs; structural analysis and site inspection for site requalification; structural response of Paks NPP reactor building; analysis and testing of model worm type tanks on shaking table; vibration test of a worm tank model; evaluation of potential hazard for operating WWER control rods under seismic excitation

New requirements for the WWER fuel and their consideration in designing the fuel assemblies

International Nuclear Information System (INIS)

Vasilchenko, I.; Ananyev, Y.

2003-01-01

In 2001-2002 the base designs of the new generation fuel assemblies for the WWER-440 and WWER-1000 reactors were developed. The ways of their further modernisation were defined. The present report deals with the urgent requirements and how they have been implemented in these designs. The assessment of the efficiency of new designs is carried out on the basis of the existing data of the world market on the cost of: Uranium concentrate; dividing operations; fabrication. It is additionally possible also to take into account the cost of transportation, storage and processing of the irradiated fuel including burial of wastes

Comparative severe accident analysis of WWER 1000/B 320 LOCA DN100 computed by computer codes ASTEC V1.1 and SCDAP/RELAP5

International Nuclear Information System (INIS)

Kalchev, B.; Dimov, D.; Tusheva, P.; Mladenov, I.

2005-01-01

This paper presents the modelling approach for LOCA 100 mm sequence for WWER 1000-B 320 type of reactor with the integral ASTEC computer code and SCDAP/RELAP5 computer code. As a basic input deck the reference input file for Balakovo NPP from the released ASTEC CD has been applied. As a first part of the calculations for the SBLOCA sequence the ASTEC v1.1 modules CESAR, DIVA and CPA have been activated in a coupled mode. For SCDAP/RELAP5 calculation input deck for WWER 1000-B 320 has been applied which meant to be closer to the initial boundary conditions applied for ASTEC WWER 1000 input deck. A SBLOCA 100 mm comparison between ASTEC v1.1 and SCADAP/RELAP5 has been presented. ASTEC predicts vessel failure at 15620 s. ASTEC and SCDAP/RELAP5 give close but not similar results - this could be observed on the trends. The comparison of 100 mm-break shows that SCDAP/RELAP5 predicts clear phenomenological changes in primary pressure evolution and molten pool formation. Similar hydrogen production mass for both codes around 5000 s is detected

Adaptation of GRS calculation codes for Soviet reactors

International Nuclear Information System (INIS)

Langenbuch, S.; Petri, A.; Steinborn, J.; Stenbok, I.A.; Suslow, A.I.

1994-01-01

The use of ATHLET for incident calculation of WWER has been tested and verified in numerous calculations. Further adaptation may be needed for the WWER 1000 plants. Coupling ATHLET with the 3D nuclear model BIPR-8 for WWER cores clearly improves studies of the influence of neutron kinetics. In the case of FBMK reactors ATHLET calculations show that typical incidents in the complex RMBK reactors can be calculated even though verification still has to be worked on. Results of the 3D-core model QUABOX/CUBBOX-HYCA show good correlation of calculated and measured values in reactor plants. Calculations carried out to date were used to check essential parameters influencing RBMK core behaviour especially dependence of effective voidre activity on the number of control rods. (orig./HP) [de

Pressurized-water reactors

International Nuclear Information System (INIS)

Bush, S.H.

1983-03-01

An overview of the pressurized-water reactor (PWR) pressure boundary problems is presented. Specifically exempted will be discussions of problems with pumps, valves and steam generators on the basis that they will be covered in other papers. Pressure boundary reliability is examined in the context of real or perceived problems occurring over the past 5 to 6 years since the last IAEA Reliability Symposium. Issues explicitly covered will include the status of the pressurized thermal-shock problem, reliability of inservice inspections with emphasis on examination of the region immediately under the reactor pressure vessel (RPV) cladding, history of piping failures with emphasis on failure modes and mechanisms. Since nondestructive examination is the topic of one session, discussion will be limited to results rather than techniques

An approach to stability analysis of spatial xenon oscillations in WWER-1000 reactors

International Nuclear Information System (INIS)

Parhizkari, H.; Aghaie, M.; Zolfaghari, A.; Minuchehr, A.

2015-01-01

Highlights: • The multipoint methodology is developed for xenon oscillation in the BNPP. • The axial, radial and azimuthal offsets are calculated in the BOC and EOC. • It is shown that the all of oscillation modes are safe in the BOC. • The axial oscillation is not safe in the EOC and needs governor control system. • The multipoint kinetics show good agreement for spatial oscillations. - Abstract: Spatial power oscillations due to spatial distribution of xenon transient are well known as xenon oscillation in large reactors. Xenon-induced spatial power oscillations occur as a result of rapid perturbations to power distribution that cause the xenon and iodine distribution to be out of phase with the perturbed power distribution. This results in a shift in xenon and iodine distributions that causes the power distribution to change in an opposite direction from the initial perturbation. In this paper xenon-induced power oscillation is described by a system of differential equations with non-linearity between xenon and flux distributions; the dynamics of process is described by a discrete distributed parameter model, with the neutron flux, the delayed neutrons, the core temperature and the xenon and iodine concentrations as the “states” of the system. It is shown that it is possible to describe the discrete distributed-parameter as a set of coupled point-reactor models. It is also shown that using this scheme it is possible to analyze the control aspects of a multi-section large core reactor by treating only two adjacent sections of the core. To illustrate the capability and efficiency of the proposed scheme Bushehr Nuclear Power Plant, BNPP, which is a WWER-1000 reactor, is chosen to show the performance of the methodology. The axial, azimuthal and radial power oscillation at the beginning of cycle, BOC, and the end of cycle, EOC, for BNPP are investigated; the results are in good agreement with safety analysis report of the reference plant

Reactor pressure boundary materials

International Nuclear Information System (INIS)

Hong, Jun Hwa; Chi, S. H.; Lee, B. S.

2002-04-01

With a long-term operation of nuclear power plants, the component materials are degraded under severe reactor conditions such as neutron irradiation, high temperature, high pressure and corrosive environment. It is necessary to establish the reliable and practical technologies for improving and developing the component materials and for evaluating the mechanical properties. Especially, it is very important to investigate the technologies for reactor pressure boundary materials such as reactor vessel and pipings in accordance with their critical roles. Therefore, this study was focused on developing and advancing the microstructural/micro-mechanical evaluation technologies, and on evaluating the neutron irradiation characteristics and radiation effects analysis technology of the reactor pressure boundary materials, and also on establishing a basis of nuclear material property database

Thermal-hydraulic analysis of total loss of steam generator feed water in WWER-440

International Nuclear Information System (INIS)

Sabotinov, L.; Cadet-Mercier, S.

2001-01-01

The analysis is carried out for a WWER-440/V270 with upgraded primary safety valves (replacement of the existing PRZ safety valves with Pilot Operated Relief Valves (PORV) of the type SEBIM (France)) The current analysis is focused on the scenario 'Total Loss of SGs Feed Water' with application of the operator action of primary system 'Feed and Bleed' in order to check the effectiveness of the installed pressurizer SEBIM valves and to verify that the operator can cool down the reactor system and cope with this accident. The calculations have been performed at the Institute of Protection and Nuclear Safety (IPSN) in Fontenay-aux-Roses with the computer code CATHARE 2 Version 1.3L1. CATHARE is a French best estimate thermal-hydraulic program for accident analysis in the light water nuclear reactors, developed with the participation of the IPSN (Institut de Protection et Surete Nucleaire), CEA (Commissariat a l'Energie Atomique), Framatome and EdF (Electricite de France). (author)

Advanced fuel cycles and burnup increase of WWER-440 fuel

International Nuclear Information System (INIS)

Proselkov, V.; Saprykin, V.; Scheglov, A.

2003-01-01

Analyses of operational experience of 4.4% enriched fuel in the 5-year fuel cycle at Kola NPP Unit 3 and fuel assemblies with Uranium-Gadolinium fuel at Kola NPP Unit 4 are made. The operability of WWER-440 fuel under high burnup is studied. The obtained results indicate that the fuel rods of WWER-440 assemblies intended for operation within six years of the reviewed fuel cycle totally preserve their operability. Performed analyses have demonstrated the possibility of the fuel rod operability during the fuel cycle. 12 assemblies were loaded into the reactor unit of Kola 3 in 2001. The predicted burnup in six assemblies was 59.2 MWd/kgU. Calculated values of the burnup after operation for working fuel assemblies were ∼57 MWd/kgU, for fuel rods - up to ∼61 MWd/kgU. Data on the coolant activity, specific activity of the benchmark iodine radionuclides of the reactor primary circuit, control of the integrity of fuel rods of the assemblies that were operated for six years indicate that not a single assembly has reached the criterion for the early discharge

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4C. Paks NPP: Analysis and testing. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material involves comparative analysis of the seismic analysis results of the reactor building for soft soil conditions, derivation of design response spectra for components and systems; and upper range design response spectra for soft soil site conditions at Paks NPP.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4C. Paks NPP: Analysis and testing. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material involves comparative analysis of the seismic analysis results of the reactor building for soft soil conditions, derivation of design response spectra for components and systems; and upper range design response spectra for soft soil site conditions at Paks NPP

Simulation of the dynamic behaviour of the secondary circuit of a WWER-440 type nuclear power plant Pt. 2

International Nuclear Information System (INIS)

Doorenbos, J.; Gacs, A.; Kiss, Zs.

1987-12-01

This report describes the dynamic simulation models of the most important controllers of the secondary circuit of a WWER-440 type nuclear power plant, i.e., the hydraulic turbine controller and the level controls of the condenser hotwell and that of the feedwater tank. Simulation results are also presented. (For dynamic simulation models of the primary circuit of WWER-440 type reactors see Reports KFKI--1983-127 and KFKI--1985-08.) (author) 15 figs

Examples for cost reduction in the design of a WWER-1000 nuclear power plant

International Nuclear Information System (INIS)

Kukkola, T.

1991-01-01

In a design project during recent years, a version for Finnish conditions has been and is being developed based on the Soviet WWER-1000 PWR plant with four horizontal steam generators. The plant will have a double containment. The inner containment will be a dry full pressure prestressed concrete containment with liner and the secondary containment will be made of ordinary concrete. Four train safety approach is adopted. It is supposed that the plant is to be designed according to the present Finnish safety requirements, e.g. severe reactor accidents are considered. When striving at an economic plant no compromises are made as far as safety is concerned. This paper describes possible cost reduction by redesigning the main technical equipment. (author). 1 ref

Investigation of large grain and Gd-doped WWER fuels behaviour at BOL in the Halden reactor

International Nuclear Information System (INIS)

Volkov, B.

2008-01-01

In this paper the following issues have been discussed: 1) WWER fuel tests in the HBWR; 2) Main objectives of the test with large grains and Gd-doped WWER fuel; 3) Analysis of of the the data at BOL focus on: Gd-doped fuel thermal behaviour, fuel elongation and dimension stability as well as cladding elongation early in life. At the end authors concluded that: 1) No indication of substantial effect of large grains on fuel thermal performance at BOL; 2) Densification observed in large grain fuel is similar to the ordinary uranium dioxide fuel with 95-96 % of theoretical density; 3) Dimension stability of large grain fuel is similar or even better than that in reference WWER fuel; 4) More stable dimension behaviour of large grain fuel at power could be attributed to its lower creep or densification at high temperature in the centre part of the fuel; 5) Cladding elongation detectors indicated identical early-in-life PCMI in both large grain and reference fuel rods, which reflected an accommodation effect of fuel pellets in claddings during first rise to power; no residual strains in either fuel types were observed; subsequent cladding elongation measurements show a trend to irradiation growth; 6) No clear evidence for densification of Gd-doped WWER fuel is observed during first irradiation cycle

Study of behaviour of radioactive iodine inorganic compounds in PWR type reactor loops

International Nuclear Information System (INIS)

Alm, M.; Johannsen, K.-H.; Dreyer, R.

1980-01-01

Compounds of radioactive iodine and its distribution between water and vapour depending on temperature, pressure and water regime of reactor coolant with water under pressure are investigated. The field of variation of parameters indicated is widened as compared with operating reactor parameters (pressure 2-14 MPa, temperature 210-335 deg C). Distribution of iodine compounds has been studied by a statistical method. For WWER-type reactors the following conclusions have been drawn: radioactive iodine in water and vapor in the first and second loops exists in the form of iodide, radioactive iodine concentration in water vapour at constant temperature and pressure mainly is depended on water pH value, radioactive iodine solubility in water vapor at normal parameters of the reactor first loop can be approximately calculated by the equation: Ksub(d)=Csub(g)/Csub(l)=(rhosub(g)/rhosub(l))sup(2), where Ksub(d) is a coefficient of solid distribution between water and vapour, rho is density c is concentration [ru

First generation WWER 440 - What is the 'reasonable' price?

International Nuclear Information System (INIS)

Pishtuhina, K.

2004-01-01

A chronological review of the international nuclear concerns and Three Mile Island and Chernobyl accidents effects on the international nuclear organizations' policies are presented. The IAEA, G 7 and EU approaches for Soviet design plants' safety and the main results from their implementation are described. The premature closure of the first generation WWER type reactors operated in Bulgaria, Lithuania and Slovakia and their unupgradability at a reasonable price are also discussed in this paper

Relap5/Mod2.5 analyses of SG primary collector head rupture in WWER-440 reactor

International Nuclear Information System (INIS)

Szczurek, J.

1995-01-01

The paper presents the results of the analyses of steam generator (SG) manifold cover rupture performed with RELAP5/MOD2.5 (version provided by RMA, Albuquerque, for PC PPS). The calculations presented are based on RELAP5 input deck for WWER-440/213 Bobunice NPP, developed within the framework of IAEA TC Project RER/9/004. The presented analyses are directed toward determining the maximum amount of reactor coolant discharged into the secondary coolant system and the maximum amount of contaminated coolant release to the atmosphere. In all cases considered in the analysis, maximum ECCS injection capacity is assumed. The paper includes only the cases without any operator actions within the time period covered by the analyses. In particular, the primary loop isolation valves are not used for isolating the broken steam generator. Two scenarios are analysed: with and without the SG safety valve stuck open

Relap5/Mod2.5 analyses of SG primary collector head rupture in WWER-440 reactor

Energy Technology Data Exchange (ETDEWEB)

Szczurek, J. [Inst. of Atomic Energy, Swierk (Poland)

1995-12-31

The paper presents the results of the analyses of steam generator (SG) manifold cover rupture performed with RELAP5/MOD2.5 (version provided by RMA, Albuquerque, for PC PPS). The calculations presented are based on RELAP5 input deck for WWER-440/213 Bobunice NPP, developed within the framework of IAEA TC Project RER/9/004. The presented analyses are directed toward determining the maximum amount of reactor coolant discharged into the secondary coolant system and the maximum amount of contaminated coolant release to the atmosphere. In all cases considered in the analysis, maximum ECCS injection capacity is assumed. The paper includes only the cases without any operator actions within the time period covered by the analyses. In particular, the primary loop isolation valves are not used for isolating the broken steam generator. Two scenarios are analysed: with and without the SG safety valve stuck open. 3 refs.

Experimental studies under the substantiation of representativeness the temperature control core of the reactor WWER-TOI

International Nuclear Information System (INIS)

Churkin, A.N.; Bezrukov, Yu.A.; Vasil'chenko, I.N.; Supronenko, M.N.; Lobachev, S.M.; Lisenkov, E.A.; Kushmanov, S.A.

2015-01-01

To justify the representativity of measurements of the temperature at the outlet of the WWER-TOI was carried out the complex of scientific-research works, including: calculation of heat-release in the KNIT and in the structural elements of the reactor core, thermohydraulic calculation of coolant in the area of location GT with the KNIT, experimental research. Experimental studies were carried out on the test facility OKB “GIDROPRESS” with non-heated rods bundle with full-scale cross-section, with length 1230 mm. During the experiments using the model of the KNIT was recorded the change on height of the temperature difference between the main flow and the more cool coolant flowing in GT. The temperature difference was created by feeding the coolant flow into the model GT coolant with temperature on 12-15℃ lower than the temperature of the coolant in space of fuel rods [ru

Relap5/Mod2.5 analyses of SG primary collector head rupture in WWER-440 reactor

Energy Technology Data Exchange (ETDEWEB)

Szczurek, J [Inst. of Atomic Energy, Swierk (Poland)

1996-12-31

The paper presents the results of the analyses of steam generator (SG) manifold cover rupture performed with RELAP5/MOD2.5 (version provided by RMA, Albuquerque, for PC PPS). The calculations presented are based on RELAP5 input deck for WWER-440/213 Bobunice NPP, developed within the framework of IAEA TC Project RER/9/004. The presented analyses are directed toward determining the maximum amount of reactor coolant discharged into the secondary coolant system and the maximum amount of contaminated coolant release to the atmosphere. In all cases considered in the analysis, maximum ECCS injection capacity is assumed. The paper includes only the cases without any operator actions within the time period covered by the analyses. In particular, the primary loop isolation valves are not used for isolating the broken steam generator. Two scenarios are analysed: with and without the SG safety valve stuck open. 3 refs.

Modernized accurate methods for processing of in-core measurement signals in WWER reactors

International Nuclear Information System (INIS)

Polak, T.

1996-01-01

Utilization of the new accurate WIMS-KAERI library (WIMKAL-88) to generate the following characteristics for Rhodium SPND: Sensitivity depletion law by high (approx= 75%) burnup of emitter; influence of burnup-history on depletion law course; influence of neutron spectrum change on Rh-SPND sensitivity caused by change of fuel enrichment, fuel burnup, moderator temperature, concentration of boracid, central pin power rate and concentration of Xe 135 ; generating and experimental testing of Rh-SPND signal to linear pin power rate and signal to neutron flux conversion factors. Rh-SPND instrumentation optimization (reduction) related to safety and operational aspects as needed for 3D power surveillance in WWER-1000 reactors. Analysis of SPND reduction from 64x7 to 46x7 by method of Shannon information entropy optimization. Influence of reduction on accuracy of 3D power distribution reconstruction. Physical methods of 3D power distribution unfolding in new modernized on-line I and C system in NPP J. Bohunice with in-core measurements according to 210 thermocouples and 36x7 Rh-SPNDs. Program system TOPRE under QNX operating system network in FORTRAN 77, neutronic background calculations by macrocode MOBY-DICK. (author). 10 refs, 6 figs, 7 tabs

Development of the temperature field at the WWER-440 core outlet monitoring system and application of the data analyses methods

International Nuclear Information System (INIS)

Spasova, V.; Georgieva, N.; Haralampieva, Tz.

2001-01-01

On-line internal reactor monitoring by 216 thermal couples, located at the reactor core outlet, is carried out during power operation of WWER-440 Units 1 and 2 at Kozloduy NPP. Automatic monitoring of technology process is performed by IB-500MA, which collects and performs initial data processing (discrediting and conversion of analogue signals into digital mode). The paper also presents the results and analyses of power distribution monitoring during the past 21-th and current 22-th fuel cycle at Kozloduy NPP, Unit 1 by using archiving system capacity and related software. The possibility to perform operational assessment and analysis of power distribution in the reactor core in each point of the fuel cycle is checked by comparison of the neutron-physical calculation results with reactor coolant system parameters. Paper shows that the processing and analysis of accumulated significant amount of data in the archive files increases accuracy and reliability of power distribution monitoring in the reactor core in each moment of the fuel cycle of WWER-440 reactors at Kozloduy NPP

Evaluated experimental database on critical heat flux in WWER FA models

International Nuclear Information System (INIS)

Artamonov, S.; Sergeev, V.; Volkov, S.

2015-01-01

The paper presents the description of the evaluated experimental database on critical heat flux in WWER FA models of new designs. This database was developed on the basis of the experimental data obtained in the years of 2009-2012. In the course of its development, the database was reviewed in terms of completeness of the information about the experiments and its compliance with the requirements of Rostekhnadzor regulatory documents. The description of the experimental FA model characteristics and experimental conditions was specified. Besides, the experimental data were statistically processed with the aim to reject incorrect ones and the sets of experimental data on critical heat fluxes (CHF) were compared for different FA models. As a result, for the fi rst time, the evaluated database on CHF in FA models of new designs was developed, that was complemented with analysis functions, and its main purpose is to be used in the process of development, verification and upgrading of calculation techniques. The developed database incorporates the data of 4183 experimental conditions obtained in 53 WWER FA models of various designs. Keywords: WWER reactor, fuel assembly, CHF, evaluated experimental data, database, statistical analysis. (author)

The simplified P3 approach on a trigonal geometry in the nodal reactor code DYN3D

International Nuclear Information System (INIS)

Duerigen, S.; Fridman, E.

2011-01-01

DYN3D is a three-dimensional nodal diffusion code for steady-state and transient analyses of Light-Water Reactors with square and hexagonal fuel assembly geometries. Currently, several versions of the DYN3D code are available including a multi-group diffusion and a simplified P 3 (SP 3 ) neutron transport option. In this work, the multi-group SP 3 method based on trigonal-z geometry was developed. The method is applicable to the analysis of reactor cores with hexagonal fuel assemblies and allows flexible mesh refinement, which is of particular importance for WWER-type Pressurized Water Reactors as well as for innovative reactor concepts including block type High-Temperature Reactors and Sodium Fast Reactors. In this paper, the theoretical background for the trigonal SP 3 methodology is outlined and the results of a preliminary verification analysis are presented by means of a simplified WWER-440 core test example. The accordant cross sections and reference solutions were produced by the Monte Carlo code SERPENT. The DYN3D results are in good agreement with the reference solutions. The average deviation in the nodal power distribution is about 1%. (Authors)

Reactor water spontaneous circulation structure in reactor pressure vessel

International Nuclear Information System (INIS)

Takahashi, Kazumi

1998-01-01

The gap between the inner wall of a reactor pressure vessel of a BWR type reactor and a reactor core shroud forms a down comer in which reactor water flows downwardly. A feedwater jacket to which feedwater at low temperature is supplied is disposed at the outer circumference of the pressure vessel just below a gas/water separator. The reactor water at the outer circumferential portion just below the air/water separator is cooled by the feedwater jacket, and the feedwater after cooling is supplied to the feedwater entrance disposed below the feedwater jacket by way of a feedwater introduction line to supply the feedwater to the lower portion of the down comer. This can cool the reactor water in the down comer to increase the reactor water density in the down comer thereby forming strong downward flows and promote the recycling of the reactor water as a whole. With such procedures, the reactor water can be recycled stably only by the difference of the specific gravity of the reactor water without using an internal pump. In addition, the increase of the height of the pressure vessel can be suppressed. (I.N.)

WWER steam generator tube structural and leakage integrity

International Nuclear Information System (INIS)

Splichal, K.; Krhounek, Vl.; Otruba, J.; Ruscak, M.

1998-01-01

The integrity of heat exchange tubes may influence the lifetime of WWER steam generators and appears to be an important criterion for the evaluation of their safety and operational reliability. The basic requirements are to assure very low probability of radioactive water leakage, preventing unstable crack growth and sudden tube rupture. These requirements led to development of permissible limits for primary to secondary leak evaluation and heat exchange tubes plugging. The stress corrosion cracking and pitting are the main corrosion damages of WWER heat exchange tubes and are initiated from the outer surface. Both the initiation and crack growth cause thinning of the tube wall and lead to part thickness cracks and through wall cracks, oriented preferentially in the axial direction. The paper presents the leakage and plugging limits for WWER steam generators, which have been determined from leak tests and burst tests. The tubes with axial part-through and through-wall defects have been used. The permissible value of primary to secondary leak rate was evaluated with respect to permissible axial through-wall defect size of WWER 440 and 1000 steam generator tubes. Blocking of the tube cracks by corrosion product particles and other compounds reduces the primary to secondary leak rate. The plugging limits involve the following factors: permissible tube wall thickness which determine further operation of the tubes with defects and assures their integrity under operating conditions and permissible size of a through-wall crack which is sufficiently stable under normal and accident conditions in relation to the critical crack length. For the evaluation of burst test of heat exchange tubes with longitudinal through-wall defects the instability criterion has been used and the dependence of the normalised burst pressure on the normalised length of an axial through-wall defect has been determined. The validity of the criterion of instability for WWER tubes with through

Some aspects of influence of coolant water chemistry on reliability of WWER and RBMK type fuels

International Nuclear Information System (INIS)

Solyany, V.I.; Bibilashvili, Yu.K.; Sukhanov, G.I.; Pimenov, Yu.V.; Gosudarstvennyj Komitet po Ispol'zovaniyu Atomnoj Ehnergii SSSR, Moscow)

1983-01-01

In WWER and RBMK reactors now in operation a good quality of primary coolant is achieved and the required corrosion resistance of structural materials and normal irradiation conditions are ensured. Data on commercial fuel operation and clad material (Zr 1% Nb alloy) condition are briefly generalized. Some results of reactor investigations of corrosion behaviour of commercial Zr 1% Nb alloy under the condition of WWER and RBMK coolant are discussed and compared. It is established that the chemical effect of coolant on fuel cladding does not in itself limit its serviceability at design burn-ups but due to the possible processes of crud formation, corrosion (total and local), fretting-corrosion and hydriding it can influence the fuel reliability. This influence is qualitatively assessed through a rise in the clad temperature, a reduction of material plasticity and clad thickness. (author)

Some aspects of influence of coolant water chemistry on reliability of WWER and RBMK type fuels

Energy Technology Data Exchange (ETDEWEB)

Solyany, V I; Bibilashvili, Yu K; Sukhanov, G I; Pimenov, Yu V [Vsesoyuznyj Nauchno-Issledovatel' skij Inst. Neorganicheskikh Materialov, Moscow (USSR); Gosudarstvennyj Komitet po Ispol' zovaniyu Atomnoj Ehnergii SSSR, Moscow)

1983-12-01

In WWER and RBMK reactors now in operation a good quality of primary coolant is achieved and the required corrosion resistance of structural materials and normal irradiation conditions are ensured. Data on commercial fuel operation and clad material (Zr 1% Nb alloy) condition are briefly generalized. Some results of reactor investigations of corrosion behaviour of commercial Zr 1% Nb alloy under the condition of WWER and RBMK coolant are discussed and compared. It is established that the chemical effect of coolant on fuel cladding does not in itself limit its serviceability at design burn-ups but due to the possible processes of crud formation, corrosion (total and local), fretting-corrosion and hydriding it can influence the fuel reliability. This influence is qualitatively assessed through a rise in the clad temperature, a reduction of material plasticity and clad thickness.

A procedure for temperature-stress fields calculation of WWER-1000 primary circuit in PTS event

Energy Technology Data Exchange (ETDEWEB)

Petkov, G [Technical Univ., Dept. Thermal and Nuclear Power Engineering, Sofia (Bulgaria); Groudev, P; Argirov, J [Bulgarian Academy of Science, Inst. for Nuclear Research and Nuclear Energy, Sofia (Bulgaria)

1997-09-01

The paper presents the procedure of an investigation of WWER-1000 primary circuit temperature-stress field by the use of thermohydraulic computation data for a pressurized thermal shock event ``Core overcooling``. The procedure is based on a model of the plane stress state with ideal contact between wall and medium for the calculation. The computation data are calculated on the base of WWER-1000 thermohydraulic model by the RELAP5/MOD3 codes. This model was developed jointly by the Bulgarian and BNL/USA staff to provide an analytical tool for performing safety analysis. As a result of calculations by codes the computation data for temperature field law (linear laws of a few distinguished parts) and pressure of coolant at points on inner surface of WWER-1000 primary circuit equipment are received. Such calculations can be used as a base for determination of all-important load-carrying sections of the primary circuit pipes and vessels, which need further consideration. (author). 7 refs, 2 figs, 2 tabs.

Structural optimization of static power control programs of nuclear power plants with WWER-1000

International Nuclear Information System (INIS)

Kokol, E.O.

2015-01-01

The question of possibility the power control programs switching for WWER-1000 is considered. The aim of this research is to determine the best program for the power control of nuclear reactor under cyclic diurnal behavior of electrical generation, as well as the switching implementation. The considered problem of finding the best control program refers to the multicriteria optimization class of problems. Operation of the nuclear power generation system simulated using the following power control programs: with constant average temperature of transfer fluid, with constant pressure in the reactor secondary circuit, with constant temperature in input of the nuclear reactor. The target function was proposed. It consists of three normalized criteria: the burn up fraction, the damage level of fuel rod array shells, as well as changes in the power values. When simulation of the nuclear power generation system operation within the life was done, the values of the selected criteria were obtained and inserted in the target function. The minimum of three values of the target function depending on the control program at current time defined the criterion of switching of considered static power control programs for nuclear power generation system

Evaluation of Pressure Changes in HANARO Reactor Hall after a Reactor Shutdown

International Nuclear Information System (INIS)

Han, Geeyang; Han, Jaesam; Ahn, Gukhoon; Jung, Hoansung

2013-01-01

The major objective of this work is intended to evaluate the characteristics of the thermal behavior regarding how the decay heat will be affected by the reactor hall pressure change and the increase of pool water temperature induced in the primary coolant after a reactor shutdown. The particular reactor pool water temperature at the surface where it is evaporated owing to the decay heat resulting in the local heat transfer rate is related to the pressure change response in the reactor hall associated with the primary cooling system because of the reduction of the heat exchanger to remove the heat. The increase in the pool water temperature is proportional to the heat transfer rate in the reactor pool. Consequently, any limit on the reactor pool water temperature imposes a corresponding limit on the reactor hall pressure. At HANARO, the decay heat after a reactor shutdown is mainly removed by the natural circulation cooling in the reactor pool. This paper is written for the safety feature of the pressure change related leakage rate from the reactor hall. The calculation results show that the increase of pressure in the reactor hall will not cause any serious problems to the safety limits although the reactor hall pressure is slightly increased. Therefore, it was concluded that the pool water temperature increase is not so rapid as to cause the pressure to vary significantly in the reactor hall. Furthermore, the mathematical model developed in this work can be a useful analytical tool for scoping and parametric studies in the area of thermal transient analysis, with its proper representation of the interaction between the temperature and pressure in the reactor hall

WWER core pattern enhancement using adaptive improved harmony search

International Nuclear Information System (INIS)

Nazari, T.; Aghaie, M.; Zolfaghari, A.; Minuchehr, A.; Norouzi, A.

2013-01-01

Highlights: ► The classical and improved harmony search algorithms are introduced. ► The advantage of IHS is demonstrated in Shekel's Foxholes. ► The CHS and IHS are compared with other Heuristic algorithms. ► The adaptive improved harmony search is applied for two cases. ► Two cases of WWER core are optimized in BOC FA pattern. - Abstract: The efficient operation and fuel management of PWRs are of utmost importance. Core performance analysis constitutes an essential phase in core fuel management optimization. Finding an optimum core arrangement for loading of fuel assemblies, FAs, in a nuclear core is a complex problem. In this paper, application of classical harmony search (HS) and adaptive improved harmony search (IHS) in loading pattern (LP) design, for pressurized water reactors, is described. In this analysis, finding the best core pattern, which attains maximum multiplication factor, k eff , by considering maximum allowable power picking factors (PPF) is the main objective. Therefore a HS based, LP optimization code is prepared and CITATION code which is a neutronic calculation code, applied to obtain effective multiplication factor, neutron fluxes and power density in desired cores. Using adaptive improved harmony search and neutronic code, generated LP optimization code, could be applicable for PWRs core with many numbers of FAs. In this work, at first step, HS and IHS efficiencies are compared with some other heuristic algorithms in Shekel's Foxholes problem and capability of the adaptive improved harmony search is demonstrated. Results show, efficient application of IHS. At second step, two WWER cases are studied and then IHS proffered improved core patterns with regard to mentioned objective functions.

Main research results in the field of nuclear power engineering of the Nuclear Reactors and Thermal Physics Institute in 2014

International Nuclear Information System (INIS)

Trufanov, A.A.; Orlov, Yu.I.; Sorokin, A.P.; Chernonog, V.L.

2015-01-01

The main results of scientific and technological activities for last years of the Nuclear Reactors and Thermal Physics Institute FSUE SSC RF - IPPE in solving problems of nuclear power engineering are presented. The work have been carried out on the following problems: justification of research and development solutions and safety of NPPs with fast reactors of new generation with sodium (BN-1200, MBIR) and lead (BREST-OD-300) coolants, justification of safety of operating and advanced NPPs with WWER reactor facilities (WWER-1000, AEhS 2006, WWER-TOI), development and benchmarking of computational codes, research and development support of Beloyarsk-3 (BN-600) and Bilibino (BN-800) NPPs operation, decommissioning of AM and BR-10 research reactors, pilot scientific studies (WWER-SKD, ITER), international scientific and technical cooperation. Problems for further investigations are charted [ru

Experimental Investigation of Coolant Mixing in WWER and PWR Reactor Fuel Bundles by Laser Optical Techniques for CFD Validation

International Nuclear Information System (INIS)

Tar, D.; Baranyai, V; Ezsoel, Gy.; Toth, I.

2010-01-01

Non intrusive laser optical measurements have been carried out to investigate the coolant mixing in a model of the head part of a fuel assembly of a WWER reactor. The goal of this research was to investigate the coolant flow around the point based in-core thermocouple; and also provide experimental database as a validation tool for computational fluid dynamics calculations. The experiments have been carried out on a full size scale model of the head part of WWER-440/213 fuel assembly. In this paper first the previous results of the research project is summarised, when full field velocity vectors and temperature were obtained by particle image velocimetry and planar laser induced fluorescence, respectively. Then, preliminary results of the investigation of the influence of the flow in the central tube will be reported by presenting velocity measurement results. In order to have well measurable effect, extreme flow rates have been set in the central tube by applying an inner tube with controlled flow rates. Despite the extreme conditions, the influence of the central tube to the velocity field proved to be significant. Further measurement will be done for the investigation of the effect of the gaps at the spacer fixings by displacing the inner tube vertically, and also the temperature distribution will also be determined at similar geometries by laser induced fluorescence. The aim of the measurements was to establish an experimental database, as well as the validation of computational fluid dynamics calculations. (Authors)

WWER-1000 Burnup Credit Benchmark (CB5)

International Nuclear Information System (INIS)

Manolova, M.A.

2002-01-01

In the paper the specification of WWER-1000 Burnup Credit Benchmark first phase (depletion calculations), given. The second phase - criticality calculations for the WWER-1000 fuel pin cell, will be given after the evaluation of the results, obtained at the first phase. The proposed benchmark is a continuation of the WWER benchmark activities in this field (Author)

Computer-based system for inspection of water chemistry regimes in WWER-type nuclear power plants

International Nuclear Information System (INIS)

Burcl, R.; Novak, M.; Malenka, P.

1993-01-01

The unsatisfactory situation in water chemistry testing at nuclear power plants with WWER type reactors is described. The testing primarily relies on laboratory analyses of manually taken samples. About 40 samples from one unit are tested per shift, which comprises approximately 250 determinations of various parameters. The time between two determinations is no shorter than 4 to 6 hours, thus rapid parameter changes between two determinations fail to be monitored. A novel system of automated chemistry monitoring is outlined, feasible for WWER type reactors. The system comprises 10 sets of sensors for monitoring all the relevant chemistry parameters of both the primary and secondary coolant circuits. Each sensor set has its own autonomous computer which secures its function even in case of loss of the chemical information network. The entire system is controlled by a master computer which also collects the results and provides contact with the power plant's information system. (Z.S.). 1 fig

Some aspects of reactor pressure vessel integrity

International Nuclear Information System (INIS)

Korosec, D.; Vojvodic, G.J.

1996-01-01

Reactor pressure vessel of the pressurized water reactor nuclear power plant is the subject of extreme interest due to the fact that presents the pressure boundary of the reactor coolant system, which is under extreme thermal, mechanical and irradiation effects. Reactor pressure vessel by itself prevents the release of fission products to the environment. Design, construction and in-service inspection of such component is governed by strict ASME rules and other forms of administrative control. The reactor pressure vessel in nuclear power plant Kriko is designed and constructed in accordance with related ASME rules. The in-service inspection program includes all requests presented in ASME Code section XI. In the present article all major requests for the periodic inspections of reactor pressure vessel and fracture mechanics analysis are discussed. Detailed and strict fulfillment of all prescribed provisions guarantee the appropriate level of nuclear safety. (author)

WWER-440 reactor emergency cooling using `feed and bleed` procedure; Avarijnoe raskholazhivanie reaktora WWER-440 s pomoshtyu protsedury `podpitka-produvka`

Energy Technology Data Exchange (ETDEWEB)

Marinov, M; Dimitrov, B; Popov, E; Avdzhiev, K [Energoproekt, Sofia (Bulgaria)

1996-12-31

A procedure for emergency cooling in the case of total loss of coolant water is proposed. `Feed and bleed` procedure is applied by the operator and its main goal is to maintain a predefined level in the primary circuit and low pressure and temperature in the reactor. Two extreme cases are considered: 1. the loss of coolant is combined with a blackout; 2. the loss of feeding water is due to a general failure in the control room. The accidents are simulated and the relevant time intervals are estimated. After a simulated operator action following the procedure the reactor temperature is evaluated to 147{sup o} C and the primary circuit pressure to 10 bar. 1 ref., 4 figs., 2 tabs.

Radiation stability and recovery of WWER-440 materials

Energy Technology Data Exchange (ETDEWEB)

Amaev, A; Kryukov, A; Levit, V; Platonov, P; Sokolov, M

1994-12-31

The main results of a complex investigation of radiation embrittlement of WWER-440 reactor vessel materials, carried out in Russia, are presented. The effect of the annealing temperature and annealing time, neutron fluence, and phosphorous and copper impurity contents on the recovery of the ductile-to-brittle transition temperature are studied. It is shown that the recovery of the transition temperature depends mainly on the annealing temperature. At an annealing temperature of 420 and 460 C, residual post-annealing embrittlement does not depend on neutron fluence. 14 figs., 3 tabs.

Radiation stability and recovery of WWER-440 materials

International Nuclear Information System (INIS)

Amaev, A.; Kryukov, A.; Levit, V.; Platonov, P.; Sokolov, M.

1993-01-01

The main results of a complex investigation of radiation embrittlement of WWER-440 reactor vessel materials, carried out in Russia, are presented. The effect of the annealing temperature and annealing time, neutron fluence, and phosphorous and copper impurity contents on the recovery of the ductile-to-brittle transition temperature are studied. It is shown that the recovery of the transition temperature depends mainly on the annealing temperature. At an annealing temperature of 420 and 460 C, residual post-annealing embrittlement does not depend on neutron fluence. 14 figs., 3 tabs

The procedure for determination of special margin factors to account for a bow of the WWER-1000 fuel assemblies

International Nuclear Information System (INIS)

Tsyganov, S. V.; Marin, S. V.; Shishkov, L. K.

2008-01-01

Starting from 1980s, the problem of bow of the WWER-1000 reactor fuel assemblies and the effect of that on the operational safety is being discussed. At the initial period of time, the extension of time for dropping control rods of the control and protection system associated with this bow posed the highest threat. Later on, new more rigid structures were developed for fuel assemblies that eliminated the problems of control rods. However, bow of the WWER-1000 reactor fuel assemblies is observed up to now. The scale of this bow reduced significantly but it still effects safety. Even a minor bow available may lead to the noticeable increase of power of individual fuel pins associated with the local variation of the coolant amount. This effect must be taken into account on designing fuel loadings to eliminate the exceeding of set limitations. The introduction of additional special margins is the standard method for taking this effect into account. The present paper describes the conservative technique for the assessment of additional margins for bow of fuel assemblies of state-of-the-art designs. This technique is employed in the WWER-1000 reactor designing. The chosen conservatism degree is discussed as well as the method for its assurance and acceptable ways for its slackening. The example of the margin evaluation for the up-to-date fuel loading is given. (authors)

Protection of WWER type primary loops against extreme effects

International Nuclear Information System (INIS)

Podrouzek, J.; Rejent, B.

1985-01-01

Dynamic analyses of the WWER-440 primary loops for the Mochovce nuclear power plant showed that the unprotected primary loop is very soft with a first eigenfrequency of 0.38 Hz. Protection with amortisseurs and viscous shock absorbers was compared and the viscous shock absorber in all cases proved to be more suitable. GERB viscous absorbers will be installed at the Mochovce nuclear power plant. First calculations of the dynamic resistance of the WWER-1000 primary loops for the Temelin nuclear power plant to extreme events were also made. It was shown that the unprotected primary loop is rather soft with a first eigenfrequency of 0.9 Hz, or 0.6 Hz at the pressurizer branch. It will therefore be necessary to protect the primary loops with viscous shock absorbers. (Z.M.)

Evaluation of fatigue crack growth in the primary circuit pipeline of a WWER 440/213c type nuclear power plant

International Nuclear Information System (INIS)

Samohyl, P.

1993-07-01

The fatigue damage of the primary circuit of WWER-440/213c reactors was evaluated proceeding from actual and design operating data of units 3 and 4 of the Bohunice V-2 nuclear power plant. A complex computation model was set up, encompassing the main circulation pipeline, pressurizer pipeline, emergency core aftercooling system pipeline, steam pipeline, and feedwater pipeline. The standardized STATIC code was applied to the stress analysis, and the FATLBB code was used to determine the crack increment for all operating states and primary circuit sections. The probability of fatigue failure of the pipelines was found to be low. (J.B.). 55 tabs., 3 figs., 9 refs

WWER safety analysis in case of simultaneous positive reactivity introduction by control rods withdrawal and pure condensate injection

International Nuclear Information System (INIS)

Kuchin, A.; Ovdiienko, I.; Khalimonchuk, V.

2011-01-01

Results of calculation assessment of positive reactivity insertion rate are presented under condition of simultaneous effect on reactivity of two provided by WWER project reactivity operation systems - extract of regulation group and decrease of boron acid concentration. Showed that maximal positive reactivity insertion rate is achieved at hot zero power and it's too less than limit value 0.07β eff /sec defined by normative document 'Nuclear safety regulation of NPP with pressurized water reactors'. For given reasons concluded that necessity of application of the extended protection PZ-2 actuation time is absent on interval of pure condensate transportation for full exclusion of possibility of positive reactivity insertion simultaneously by two different operation systems. (Authors)

Proof, interpretation and evaluation of radiation-induced microstructural changes in WWER reactor pressure vessel steels

International Nuclear Information System (INIS)

Boehmert, J.; Gokhman, A.; Grosse, M.; Ulbricht, A.

2003-06-01

Neutron embrittlement is a special issue for the VVER-type reactors. One of the fundamentals for a reliable assessment of the current material state is knowledge of the causes and mechanisms of neutron embrittlement. The aim of the project is to understand and to quantify the microstructural appearances due to neutron radiation in VVER-type reactor pressure vessel steels. The material base is a broad variation of irradiation probes taken from the irradiation programme Rheinsberg, surveillance programmes of Russian, Ukrainian or Hungarian NPPs or irradiation experiments with mockup-alloys. The microstructure was investigated by different methods. The small angle neutron scattering (SANS) proved to be the most suitable method. A procedure was developed to determine mean diameter, size distribution and volume fraction of irradiation-induced microstructure from SANS experiments in a reliable and comparable manner. With this method microstructural parameters were systematically determined and the main factors of influence were identified. Apart from the neutron fluence the volume fraction of radiation defects mainly changes with the copper or nickel content whereas phosphorus is hardly relevant. Annealing remedies the radiation-induced microstructural appearances. The ratio between nuclear and magnetic neutron scattering provides information on the type of radiation defects. This leads to the conclusion that the material composition changes the radiation defects. The change occurs gradually rather than abruptly. The radiation defects detected by SANS correlate with the radiation hardening and embrittlement. Generally, the results suggest a bimodal mechanism due to radiation-enhanced and radiation-induced defect evolution. A kinetic model on base of the rate theory approach was established. (orig.)

Seismic strengthening of overhead roads between reactor buildings of WWER-1000 MW type NPP

International Nuclear Information System (INIS)

Stoyanov, G.; Jordanov, M.

2005-01-01

This paper presents results obtained during the upgrading design of overhead roads (OHR) between WWER-1000 MW Reactor Units at Kozloduy NPP. In order to avoid the deficiencies of OHR seismic capacity different approaches were developed based on the site and structure specifics. Overhead roads are precasted RC structures. They consist of pedestrian gallery and pipeline RC box, connecting reactor buildings with auxiliary building. They are mounted at approximately 10 m above ground level. The overhead roads are evaluated at their as-is status and a seismic upgrading of the structure is designed. The analysis of the upgraded structure is performed for Review Level Earthquake (RLE). Soil-Structure Interaction (SSI) effects are taken into account through equivalent soil springs with frequency adjusted stiffnesses. The upgraded structure is checked for conformance with the specially developed technical design specification based on International, US and Bulgarian standards and codes, taking into account site specific conditions. The general approach is consistent with up-to-date practice for evaluation and upgrade of nuclear power plant facilities. The existing site conditions and Owner's requirements are taken into account during development of the upgrading. The proposed upgrading measures can be divided in two major categories global and local. Special attention is paid to improvement of the ductile behavior of the structure through new detailing and upgrading of existing connection. These measures are grouped in two final design concepts and after a comparative study one of them is chosen for implementation. For the upgraded structure response spectra are derived at locations where equipment is attached. (authors)

The requirements to informativity of FFD Methods on NPP with WWER at acceptance of the concept of zero refusal

International Nuclear Information System (INIS)

Miglo, V.; Girchenko, A.

2015-01-01

The paper reviewed current approaches to detect fuel failures during reactor operation and during refueling outages in WWER s. Generally, the diagnosis of leaking fuel is performed in three steps. First, failure parameters are estimated by coolant activity during reactor operation. Second, leaking fuel is detected by sipping in the mast of the refueling machine. Third, additional leakage test is performed in most WWER units to confirm the leak and sometimes to evaluate failure parameters (equivalent hydraulic size of the defect in cladding may be estimated during this activity). These additional leakage tests are performed in the special casks in the spent fuel pool. Uncertainties and limitations of analytical diagnosis of failure parameters during reactor operation are mainly due to a variety of operating conditions of fuel assemblies in the core (e.g. different and broader range of the heat rates, variety of fuel enrichments, and different amounts of Gd, mixed cores)

Review and comparison of WWER and LWR Codes and Standards

International Nuclear Information System (INIS)

Buckthorpe, D.; Tashkinov, A.; Brynda, J.; Davies, L.M.; Cueto-Felgeueroso, C.; Detroux, P.; Bieniussa, K.; Guinovart, J.

2003-01-01

The results of work on a collaborative project on comparison of Codes and Standards used for safety related components of the WWER and LWR type reactors is presented. This work was performed on behalf of the European Commission, Working Group Codes and Standards and considers areas such as rules, criteria and provisions, failure mechanisms , derivation and understanding behind the fatigue curves, piping, materials and aging, manufacturing and ISI. WWERs are essentially designed and constructed using the Russian PNAE Code together with special provisions in a few countries (e.g. Czech Republic) from national standards. The LWR Codes have a strong dependence on the ASME Code. Also within Western Europe other codes are used including RCC-M, KTA and British Standards. A comparison of procedures used in all these codes and standards have been made to investigate the potential for equivalencies between the codes and any grounds for future cooperation between eastern and western experts in this field. (author)

WWER fuel performance, development, QA and future prospects at Loviisa NPS

Energy Technology Data Exchange (ETDEWEB)

Loesoenen, P [Imatran Voima Oy, Vantaa (Finland)

1994-12-31

The essential characteristics of Loviisa fuel service are presented. A brief description is given of the steps in developing the performance values including: burnup dependent linear heat rate for fuel rods, comparison of measured and calculated cladding creep down of some rods, development of average discharge burnup for unit 1 and unit 2, results from experimental irradiation of test rods in research reactors. Some noticeable design changes performed and in-reactor behaviour of the lead fuel assemblies are also discussed. The quality assurance of the fuel procurement and operation is explained. Future prospects are connected with power raise of Loviisa reactors, discontinuing of spent fuel transportation to Russia for final disposal and new WWER fuel deliverers. 4 figs., 1 tab., 8 refs.

Simulation of protected and unprotected loss of flow transients in a WWER-1000 reactor based on the Drift-Flux model

Energy Technology Data Exchange (ETDEWEB)

Baghban, Ghonche [Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of). Nuclear Science and Technology Research Inst.; Shayesteh, Mohsen [Imam Hussein Univ., Tehran (Iran, Islamic Republic of). Dept. of Physics; Bahonar, Majid [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Dept. of Nuclear Engineering

2017-03-15

In view of the importance of studying coolant transient behavior in a nuclear reactor, this work is devoted to the thermal-hydraulic analysis of protected and unprotected loss of flow transients in a WWER-1000 reactor. A series of corresponding mathematical and physical models based on the four-equation Drift-Flux model has been applied. Based on a multi-channel approach, the core has been divided into different regions. Each region has different characteristics as represented in a single fuel pin with its associated coolant channel. Appropriate initial and boundary conditions have been considered and two situations of tripping four and two primary pumps in a protected core in addition to situation of tripping all four pumps in an unprotected core have been analyzed. For each transient, a full range of thermal-hydraulic parameters has been obtained. For verification of the proposed model, the results have been compared with those of the RELAP5/MOD3 and Bushehr nuclear power plant Final Safety Analysis Report (FSAR). A good agreement between results has been attained for the aforementioned transients.

Results of the safety analyses for the Greifswald and Stendal WWER nuclear power plants

International Nuclear Information System (INIS)

Milhem, J.L.

1993-03-01

Following a brief introduction of the design features of the three types of the WWER reactors, the paper deals with the main issues of the safety-related design and the most important recommendations which have been derived for upgrading measures. Furthermore some operational safety aspects of the VVER-1000 will be discussed in some detail

Pressure releasing device for reactor container

International Nuclear Information System (INIS)

Takeda, Mika.

1994-01-01

In the present invention, dose rate to public caused by radioactive rare gases can be decreased. That is, a reactor container contains a reactor pressure vessel incorporating a reactor core. There are disposed a pressure releasing system for releasing the pressure in the reactor pressure vessel to the outside, and a burning device for burning gases released from the pressure releasing system. An exhaustion pipe is disposed to the pressure releasing system. A burning device is disposed to the exhaustion pipe. It is effective to dispose a ventilation port at a portion of the exhaustion pipe upstream of the burning device. In addition, the burning device may preferably be disposed in a multi-stage in the axial direction of the exhaustion pipe. With such procedures, hydrogen in gases discharged along with the release of the pressure in the container is burned. Buoyancy is caused to the exhaustion gases by heat energy upon burning. Since the exhaustion gases can reach a higher level by the buoyancy, the dose rate due to the rare gases can be reduced. (I.S.)

MOST-7 program for calculation of nonstationary operation modes of the nuclear steam generating plant with WWER

International Nuclear Information System (INIS)

Mysenkov, A.I.

1979-01-01

The MOST-7 program intended for calculating nonstationary emergency models of a nuclear steam generating plant (NSGP) with a WWER reactor is considered in detail. The program consists of the main MOST-7 subprogram, two main subprograms and 98 subprograms-functions. The MOST-7 program is written in the FORTRAN language and realized at the BESM-6 computer. Program storage capacity in the BESM-6 amounts to 73400 words. Primary information input into the program is carried out by means of information input operator from punched cards and DATA operator. Parameter lists, introduced both from punched cards and by means of DATA operator are tabulated. The procedure of calculational result output into printing and plotting devices is considered. Given is an example of calculating the nonstationary process, related to the loss of power in six main circulating pumps for NSGP with the WWER-440 reactor

SEJV2 software package for radiation monitoring system of WWER 440 NPP

International Nuclear Information System (INIS)

Kapisovsky, V.; Jancik, O.; Kubik, I.; Bena, J.

1993-01-01

The main part of the radiation monitoring system at a WWER-440 (213 reactor type) nuclear power plant is the centralized 400-channel monitoring system 'SEJVAL' servicing twin reactor units. The SEJV2 software package is described developed to run on a PC with an IFS2 interface to the SEJVAL radiation monitoring system. It provides enhanced data presentation, record keeping and report generation, thus improving the efficiency of the health physics shift. The system was for the first time implemented at the Jaslovske Bohunice V-2 nuclear power plant with encouraging results. (Z.S.) 3 refs

Thermohydraulic accident behavior of reactors. Thermohydraulisches Stoerfallverhalten der Reaktoren in Greifswald

Energy Technology Data Exchange (ETDEWEB)

Horche, W.; Kirmse, R.; Reichenbach, D.; Weber, J.P. (Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Garching (Germany))

1992-12-01

GRS, on behalf of the German Federal Ministry for the Environment, conducted an assessment of the technical safety of the Greifswald nuclear generating units of the Soviet WWER-440/W-230 and W-213 reactor lines, respectively. The evaluation of existing accident analyses and the execution of some first calculations by GRS added to the know-how of GRS. This is reflected in the increased participation by GRS in international expert bodies investigating safety problems of WWER-440 plants. The contributions made towards international WWER projects within the framework of IAEA missions or as a result of bilateral consultations strengthen international partnership in the field of reactor safety in Central and Eastern Europe. (orig.).

Irradiation embrittlement mitigation

Energy Technology Data Exchange (ETDEWEB)

Torronen, K; Pelli, R; Planman, T; Valo, M [Technical Research Centre of Finland, Jyvaeskylae (Finland). Combustion and Thermal Engineering Lab.

1994-12-31

Mitigation methods for reducing the irradiation damage on pressure vessel materials are reviewed: load leakage loading schemes are commonly used in PWRs to mitigate reactor pressure vessel embrittlement; dummy assemblies have been applied in WWER 440-type and in some old western power plants, when exceptional fast embrittlement has been encountered; shielding of the pressure vessel has been developed, but is not in common use; pre-stressing the pressure vessel has been proposed for preventing PTS failures, but its applicability is not yet demonstrated. The large number of successful annealing treatments performed in WWER 440 type reactors as well as research on the effects of annealing treatments suggest applications for western PWRs. The emergency core cooling systems have been modified in WWER 440-type reactors in connection with other mitigation measures. (authors). 37 refs., 18 figs., 2 tabs.

Irradiation embrittlement mitigation

International Nuclear Information System (INIS)

Torronen, K.; Pelli, R.; Planman, T.; Valo, M.

1993-01-01

Mitigation methods for reducing the irradiation damage on pressure vessel materials are reviewed: load leakage loading schemes are commonly used in PWRs to mitigate reactor pressure vessel embrittlement; dummy assemblies have been applied in WWER 440-type and in some old western power plants, when exceptional fast embrittlement has been encountered; shielding of the pressure vessel has been developed, but is not in common use; pre-stressing the pressure vessel has been proposed for preventing PTS failures, but its applicability is not yet demonstrated. The large number of successful annealing treatments performed in WWER 440 type reactors as well as research on the effects of annealing treatments suggest applications for western PWRs. The emergency core cooling systems have been modified in WWER 440-type reactors in connection with other mitigation measures. (authors). 37 refs., 18 figs., 2 tabs

Reactor pressure vessel design

International Nuclear Information System (INIS)

Foehl, J.

1998-01-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. In chapter 2, the general principles of reactor pressure vessel design are elaborated. Crack and fracture initiation and propagation are treated in some detail

WWER core pattern enhancement using adaptive improved harmony search

Energy Technology Data Exchange (ETDEWEB)

Nazari, T. [Nuclear Engineering Department, Shahid Beheshti University, G.C., P.O. Box 1983963113, Tehran (Iran, Islamic Republic of); Aghaie, M., E-mail: M_Aghaie@sbu.ac.ir [Nuclear Engineering Department, Shahid Beheshti University, G.C., P.O. Box 1983963113, Tehran (Iran, Islamic Republic of); Zolfaghari, A.; Minuchehr, A.; Norouzi, A. [Nuclear Engineering Department, Shahid Beheshti University, G.C., P.O. Box 1983963113, Tehran (Iran, Islamic Republic of)

2013-01-15

Highlights: Black-Right-Pointing-Pointer The classical and improved harmony search algorithms are introduced. Black-Right-Pointing-Pointer The advantage of IHS is demonstrated in Shekel's Foxholes. Black-Right-Pointing-Pointer The CHS and IHS are compared with other Heuristic algorithms. Black-Right-Pointing-Pointer The adaptive improved harmony search is applied for two cases. Black-Right-Pointing-Pointer Two cases of WWER core are optimized in BOC FA pattern. - Abstract: The efficient operation and fuel management of PWRs are of utmost importance. Core performance analysis constitutes an essential phase in core fuel management optimization. Finding an optimum core arrangement for loading of fuel assemblies, FAs, in a nuclear core is a complex problem. In this paper, application of classical harmony search (HS) and adaptive improved harmony search (IHS) in loading pattern (LP) design, for pressurized water reactors, is described. In this analysis, finding the best core pattern, which attains maximum multiplication factor, k{sub eff}, by considering maximum allowable power picking factors (PPF) is the main objective. Therefore a HS based, LP optimization code is prepared and CITATION code which is a neutronic calculation code, applied to obtain effective multiplication factor, neutron fluxes and power density in desired cores. Using adaptive improved harmony search and neutronic code, generated LP optimization code, could be applicable for PWRs core with many numbers of FAs. In this work, at first step, HS and IHS efficiencies are compared with some other heuristic algorithms in Shekel's Foxholes problem and capability of the adaptive improved harmony search is demonstrated. Results show, efficient application of IHS. At second step, two WWER cases are studied and then IHS proffered improved core patterns with regard to mentioned objective functions.

First qualitative analysis of fuel irradiation results carried out in the MR reactor on WWER-1000 fuel

Energy Technology Data Exchange (ETDEWEB)

Chantoin, P [International Atomic Energy Agency, Vienna (Austria); Dubrovin, K; Platonov, P [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation); Onufriev, V [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation)

1994-12-31

Four experiments carried out in the MR reactor are evaluated. They are aimed to assess the influence of burnup and the size of the pellet central hole on the fuel temperature and thus on the fuel swelling and fission gas release. The experiments have been performed at different linear rate and burnup of the fuel rods which are above the actual licensed values in WWER power stations. In this paper the results on WWER fuel rod behaviour are examined. The main fabrication and irradiation characteristics for each experiment are given. The main results from destructive and non-destructive examinations are summarized. They include: burnup determination by gamma spectroscopy, caesium shifting along fuel column and accumulation at the end of the fuel stack, fission gas release. fuel rod diameter and length change and macro-graphs showing the central hole size and the morphology after irradiation. From observation of fuel structure, Cs spectrometry and fission gas release, a large degradation of fuel thermal conductivity can be identified at high burnup. If the fuel burnup is the right parameter to be considered, burnup limits identified are: 0 70-75 MWd/kg for rods with large central hole; (2) 58-64 MWd/kg for rods with small central hole. As a general conclusion it is stressed the importance of the study due to irradiation beyond the usual linear rates at high burnup. Up to now the fuel life limiting factor was cladding corrosion when using Zircaloy-4. As the cladding corrosion situation improves, the next life limiting factor to be met could be the fuel itself. The decreasing fuel thermal conductivity is probably of prime importance and should be further studied and modelled. 5 tabs., 5 figs., 3 refs.

Dismantling id the reactor pressure vessel insulation and dissecting of the MZFR reactor pressure vessel

International Nuclear Information System (INIS)

Loeb, Andreas; Stanke, Dieter; Thoma, Markus; Eisenmann, Beata; Prechtl, Erwin; Dehnke, Burckhard

2008-01-01

The MZFR reactor was decommissioned in 1984. The authors describe the dismantling of the reactor pressure vessel insulation that consists of asbestos containing mineral fiber wool. The appropriate remote handling and cutting tools had to be adapted with respect to the restrained space in the containment. The dismantling of the reactor pressure vessel has been completed, the dissected parts have been packaged into 200 containers for the final repository Konrad. During the total project time no reportable events and no damage to persons occurred.

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4F. Paks NPP: Analysis and testing. Working material

International Nuclear Information System (INIS)

1999-01-01

In August 1991, following the SMiRT-11 Conference in Tokyo, a Technical Committee Meeting was held on the 'Seismic safety issues relating to existing NPPs'. The Proceedings of this TCM was subsequently compiled in an IAEA Working Material. One of the main recommendations of this TCM, called for the harmonization of criteria and methods used in Member States in seismic reassessment and upgrading of existing NPPs. Twenty four institutions from thirteen countries participated in the CRP named 'Benchmark study for the seismic analysis and testing of WWER type NPPs'. Two types of WWER reactors (WWER-1000 and WWER-440/213) selected for benchmarking. Kozloduy NPP Units 5/6 and Paks NPP represented these respectively as prototypes. Consistent with the recommendations of the TCM and the working paper prepared by the subsequent Consultants' Meeting, the focal activity of the CRP was the benchmarking exercises. A similar methodology was followed both for Paks NPP and Kozloduy NPP Unit 5. Firstly, the NPP (mainly the reactor building) was tested using a blast loading generated by a series of explosions from buried TNT charges. Records from this test were obtained at several free field locations (both downhole and surface), foundation mat, various elevations of structures as well as some tanks and the stack. Then the benchmark participants were provided with structural drawings, soil data and the free field record of the blast experiment. Their task was to make a blind prediction of the response at preselected locations. The analytical results from these participants were then compared with the results from the test. Although the benchmarking exercises constituted the focus of the CRP, there were many other interesting problems related to the seismic safety of WWER type NPPs which were addressed by the participants. These involved generic studies, i.e. codes and standards used in original WWER designs and their comparison with current international practice; seismic analysis

Fuel assembly outlet temperature profile influence on core by-pass flow and power distribution determination in WWER -440 reactors

International Nuclear Information System (INIS)

Petenyi, V.; Klucarova, K.; Remis, J.

2003-01-01

The in core instrumentation of the WWER-440 reactors consists of the thermocouple system and the system of self powered detectors (SPD). The thermocouple systems are positioned about 50 cm above the fuel bundle upper flow-mixing grid. The usual assumption is that, the coolant is well mixed in the Tc location, i.e. the temperature is constant through the flow cross-section area. The present evaluations by using the FLUENT 5.5.14 code reveal that, this assumption is not fulfilled. There exists a temperature profile that depends on fuel assembly geometry and on inner power profile of the fuel assembly. The paper presents the estimation of this effect and its influence on the core power distribution and the core by-pass flow determination. Comparison with measurements in Mochovce NPP will also be a part of this presentation (Authors)

Modelling of WWER-440 fuel rod behaviour under operational conditions with the PIN-micro code

International Nuclear Information System (INIS)

Stefanova, S.; Vitkova, M.; Simeonova, V.; Passage, G.; Manolova, M.; Haralampieva, Z.; Scheglov, A.; Proselkov, V.

1997-01-01

The report summarizes the first practical experience obtained by fuel rod performance modelling at the Institute for Nuclear Research and Nuclear Energy, Bulgarian Academy of Sciences. The results of application of the PIN-micro code and the code modification PINB1 for thermomechanical analysis of WWER-440 fuel assemblies (FAs) are presented. The aim of this analysis is to study the fuel rod behaviour of the operating WWER reactors. The performance of two FAs with maximal linear power and varying geometrical and technological parameters is analyzed. On the basis of recent publications on WWER fuel performance modelling at extended burnup, a modified PINB1 version of the standard PIN-micro code is shortly described and applied for the selected FAs. Comparison of the calculated results is performed. The PINB1 version predicts higher fuel temperatures and more adequate FGR rate, accounting for the extended burnup. The results presented in this paper prove the existence of sufficient safety margins, for the fuel performance limiting parameters during the whole considered period of core operation. (author). 8 refs, 16 figs, 1 tab

Modelling of WWER-440 fuel rod behaviour under operational conditions with the PIN-micro code

Energy Technology Data Exchange (ETDEWEB)

Stefanova, S; Vitkova, M; Simeonova, V; Passage, G; Manolova, M [Institute for Nuclear Research and Nuclear Energy, Sofia (Bulgaria); Haralampieva, Z [National Electric Company Ltd., Kozloduy (Bulgaria); Scheglov, A; Proselkov, V [Institute of Nuclear Reactors, RSC Kurchatov Inst., Moscow (Russian Federation)

1997-08-01

The report summarizes the first practical experience obtained by fuel rod performance modelling at the Institute for Nuclear Research and Nuclear Energy, Bulgarian Academy of Sciences. The results of application of the PIN-micro code and the code modification PINB1 for thermomechanical analysis of WWER-440 fuel assemblies (FAs) are presented. The aim of this analysis is to study the fuel rod behaviour of the operating WWER reactors. The performance of two FAs with maximal linear power and varying geometrical and technological parameters is analyzed. On the basis of recent publications on WWER fuel performance modelling at extended burnup, a modified PINB1 version of the standard PIN-micro code is shortly described and applied for the selected FAs. Comparison of the calculated results is performed. The PINB1 version predicts higher fuel temperatures and more adequate FGR rate, accounting for the extended burnup. The results presented in this paper prove the existence of sufficient safety margins, for the fuel performance limiting parameters during the whole considered period of core operation. (author). 8 refs, 16 figs, 1 tab.

Fundamentals of pressurized water reactors

International Nuclear Information System (INIS)

Murray, L.

1982-01-01

In many countries, the pressurized water reactor (PWR) is the most widely used, even though it requires enrichment of the uranium to about 3% in U-235 and the moderator-coolant must be maintained at a high pressure, about 2200 pounds per square inch. Our objective in this series of seven lectures is to describe the design and operating characteristics of the PWR system, discuss the reactor physics methods used to evaluate performance, examine the way fuel is consumed and produced, study the instrumentation system, review the physics measurements made during initial startup of the reactor, and outline the administrative aspects of starting up a reactor and operating it safely and effectively

Report of a consultants meeting on accidents during shutdown conditions for WWER nuclear power plants. Extrabudgetary programme on the safety of WWER NPPs

International Nuclear Information System (INIS)

1996-07-01

The main objectives of the meeting were to exchange information on the operational occurrences, studies performed and countermeasures taken for the accidents during shutdown for WWERs, and to define the necessity and directions of the further activities which may promote the improvement of WWER safety under shutdown conditions. The consultants have discussed some aspects concerning vulnerability of safety functions during shutdown conditions, several steps required to performed accident analysis and selected operational aspects for shutdown conditions. The discussion was supported by an evaluation of selected operational occurrences. The consultants have agreed that the discussion during the meeting in major parts is relevant to all the WWER designs (i.e. WWER-1000, WWER-440/213 and WWER-440/230). As for the plant conditions, the consultants have agreed to bound the discussion mainly by the cold shutdown and refuelling modes. Refs, figs, tabs

Pressure Tube and Pressure Vessel Reactors; certain comparisons

Energy Technology Data Exchange (ETDEWEB)

Margen, P H; Ahlstroem, P E; Pershagen, B

1961-04-15

In a comparison between pressure tube and pressure vessel type reactors for pressurized D{sub 2}O coolant and natural uranium, one can say that reactors of these two types having the same net electrical output, overall thermal efficiency, reflected core volume and fuel lattice have roughly the same capital cost. In these circumstances, the fuel burn-up obtainable has a significant influence on the relative economics. Comparisons of burn-up values made on this basis are presented in this report and the influence on the results of certain design assumptions are discussed. One of the comparisons included is based on the dimensions and ratings proposed for CANDU. Moderator temperature coefficients are compared and differences in kinetic behaviour which generally result in different design philosophies for the two types are mentioned, A comparison of different methods of obtaining flux flattening is presented. The influence of slight enrichment and other coolants, (boiling D{sub 2}O and gases) on the comparison between pressure tube and pressure vessel designs is discussed and illustrated with comparative designs for 400 MW electrical output. This paper was presented at the EAES Enlarged Symposium on Heterogeneous Heavy Water Power Reactors, Mallorca, October 10 - 14, 1960.

Pressure Tube and Pressure Vessel Reactors; certain comparisons

International Nuclear Information System (INIS)

Margen, P.H.; Ahlstroem, P.E.; Pershagen, B.

1961-04-01

In a comparison between pressure tube and pressure vessel type reactors for pressurized D 2 O coolant and natural uranium, one can say that reactors of these two types having the same net electrical output, overall thermal efficiency, reflected core volume and fuel lattice have roughly the same capital cost. In these circumstances, the fuel burn-up obtainable has a significant influence on the relative economics. Comparisons of burn-up values made on this basis are presented in this report and the influence on the results of certain design assumptions are discussed. One of the comparisons included is based on the dimensions and ratings proposed for CANDU. Moderator temperature coefficients are compared and differences in kinetic behaviour which generally result in different design philosophies for the two types are mentioned, A comparison of different methods of obtaining flux flattening is presented. The influence of slight enrichment and other coolants, (boiling D 2 O and gases) on the comparison between pressure tube and pressure vessel designs is discussed and illustrated with comparative designs for 400 MW electrical output. This paper was presented at the EAES Enlarged Symposium on Heterogeneous Heavy Water Power Reactors, Mallorca, October 10 - 14, 1960

The BN-1800 advanced sodium cooled fast reactor meeting requirements to nuclear power engineering of the XXI century

International Nuclear Information System (INIS)

Poplavskij, V.M.; Tsibulya, A.M.; Kamaev, A.A.

2004-01-01

Basic principles and direction of the elaboration of sodium fast reactor BN-1800 are discussed. The elaboration of the BN-1800 reactor is based on the scientific justified technical feasibilities of BN-350, BN-600 and BN-800 reactors. Descriptions of power blocks and reactor core of the elaborated reactor are presented. Characteristics of the BN-1800 steam generator are given. Safety of reactor unit is estimated, fundamental technical and economic indexes of BN-1800 are discussed. Economic indexes of the BN-1800 reactor are noted to be on the level of WWER-1000 and WWER-1500 reactors [ru

Pressure tube type research reactor

International Nuclear Information System (INIS)

Ueda, Hiroshi.

1975-01-01

Object: To permit safe and reliable replacement of primary pipes by providing a reactor container so as to surround a pressure pipe, with upper portions of the two separably coupled together, and coupling the pressure pipe and primary piping by joint coupling above and below the reactor container, with the lower coupling joint surrounded by drain receptacle. Structure: At the time of replacement of a pressure pipe, a partition valve is opened to exhaust primary cooling water within pressure pipe and upper and lower portions of the primary piping and replace the decelerator within the reactor container with water of the same quality as that of pool water within an upper shield pool. Thereafter, the entire space above the drain receptacle is filled with pool water by closing a partition valve and opening a water supply valve. Then, upper portion seal cover, pool bottom lid, upper joint and upper portion primary piping are removed, then bolts and nuts are loosened, and the pressure pipe is taken out together with the shield block. (Kamimura, M.)

Method of repairing pressure tube type reactors

International Nuclear Information System (INIS)

Asada, Takashi.

1983-01-01

Purpose: To enable to re-start the reactor operation in a short time, upon occurrence of failures in a pressure tube, as well as directly examine the cause for the failures in the pressure tube. Method: The pressure tube reactor main body comprises a calandria tank of a briquette form, pressure tubes, fuel assemblies and an iron-water shielding body. If failure is resulted to a pressure tube, the reactor operation is at first shutdown and nuclear fuel assemblies are extracted to withdraw from the pressure tube. Then, to an inlet pipe way and an outlet pipeway connected to the failed pressure tube, are attached plugs by means of welding or the like at the appropriate position where the radiation exposure dose is lower and the repairing work can be performed with ease. The pressure tube is disconnected to withdraw from the inlet pipeway and the outlet pipeway and, instead, radiation shielding plug tube is inserted and shield cooling device is actuated if required, wherein the reactor is actuated to re-start the operation. (Yoshino, Y.)

Design studies on staffing requirements for the new generation nuclear power units of WWER-640 and BN-800 reactor types

International Nuclear Information System (INIS)

Solovyov, D.F.

2001-01-01

The paper outlines the main staffing requirements for the new generation power units with nuclear reactors. These requirements were developed taking into account IAEA recommendations. NPP staffing structure is described, including the main and auxiliary personnel. The main principles of personnel number determination are given. Special attention is taken to the issues of personnel skill and training, including both theoretical education and practical work on the power units in operation. The use of simulators, system of knowledge control and structure of training are considered. ''Shopless'' staffing structure approach is proposed for the NPP, assuming that the main scope of repair work is performed by the central repair organization, thus increasing the quality of repair and decreasing the number of personnel on the plant. Data are given on the personnel number for the WWER-640 and the BN-800 reactor designs. Specialists of the ''ATOMENERGOPROJECT'' Institute started their work on staffing on the early development stage of the basic design of WWER-640 reactor power unit which is the forerunner of the new generation reactors. This work was based on the approaches taken by the chief engineers of NPPs in operation during their meeting held in 1989 in Kalinin NPP. At this meeting definite decision was taken on changing over to involving manufacturer in the repair work of NPP components using manufacturer's technology. In 1992 the meeting of representatives of suppliers of the main components was held where representatives of ''ATOMENERGOREMONT'' and ''LENENERGOREMONT'' were present. The suppliers agreed on carrying out repair works on the components they produced. For this purpose special departments were set up having some experience. This repair work is already carried out by ''ATOMENERGOREMONT'' on some nuclear power plants. ''LENENERGOREMONT'' has gained considerable experience in this kind of repair work on the turbines of LO-1 and LO-2 NPP in Finland. Within the

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 2. Generic material: Codes, standards, criteria. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports related to generic material, namely codes, standards and criteria for benchmark analysis

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 2. Generic material: Codes, standards, criteria. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports related to generic material, namely codes, standards and criteria for benchmark analysis.

Development and using computer codes for improvement of defect assembly detection on Russian WWER NPPs

International Nuclear Information System (INIS)

Likhanskii, V.; Evdokimov, I.; Zborovskii, V.; Kanukova, V.; Sorokin, A.; Taran, M.; Ugrumov, A.; Riabinin, Y.

2009-01-01

Diagnostic methods of fuel failure detection for improving the radiation safety and shortening of fuel reload time at Russian WWERs are currently in development . The works include creation new computer means for increase of effectiveness of fuel monitoring and reliability of leakage tests. Reliability of failure detection can be noticeably improved when we apply an integrated approach including the following methods. The first is fuel failure analysis under operating conditions. Analysis is performed with the pilot version of the expert system, which has been developed on the basis of the mechanistic code RTOP-CA. The second stage of failure monitoring is 'sipping' tests in the mast of the refueling machine. The leakage tests are the final stage of failure monitoring. A new technique with pressure cycling in the specialized casks was introduced to meet the requirements of higher reliability in detection/confirmation of the leakages. Measurements of the activity release kinetics during the pressure cycling and handling of the acquired data with the RTOP-LT code enable to evaluate a defect size in leaking fuel assembly. The mechanistic codes RTOP-CA and RTOP-LT were verified on a base of specialized experimental data and currently the code were certified by Russian authorities Rostechnadzor. Now the pressure cycling method in the specialized casks has official status and is utilized at the all Russian WWER units. Some results of application of the integrated approach to fuel failure monitoring at several Russian NPPs with WWER units are reported in the present paper. Predictions of the current version of the expert system are compared with the results of the leakage tests and with the estimations of the defect size by the pressure cycling technique. Using the RTOP-CA code the level of activity is assessed for the following fuel campaign if the leaking fuel assembly was decided to be reloaded into the core. A project of the automated computer system on the basis of

Reactor Safety Commission Code of Practice for Pressurized Water Reactors

International Nuclear Information System (INIS)

1990-01-01

The Reactor Safety Commission of the Federal German Republic has summarized in the form of Official Guidelines the safety requirements which, in the Commission's view, have to be met in the design, construction and operation of a nuclear power station equipped with a pressurized water reactor. The Third Edition of the RSK Guidelines for pressurized water reactors dated 14.10.81. is a revised and expanded version of the Second Edition dated 24.1.79. The Reactor Safety Commission will with effect from October 1981 use these Guidelines in consultations on the siting of and safety concept for the installation approval of future pressurized water reactors and will assess these nuclear power stations during their erection in the light of these Guidelines. They have not however been immediately conceived for the adaptation of existing nuclear power stations, whether under construction or in operation. The scope of application of these Guidelines to such nuclear power stations will have to be examined for each individual case. The main aim of the Guidelines is to simplify the consultation process within the reactor Safety Commission and to provide early advice on the safety requirements considered necessary by the Commission. (author)

A new concept for filtration units for trapping radioactive aerosols and iodine in the ventilation systems of nuclear power plants with WWER reactors

International Nuclear Information System (INIS)

Foerster, V.; Slanina, S.

1985-01-01

The paper describes a concept for new filtration units in the ventilation systems of nuclear power plants with WWER reactors. The new units are characterized by more stringent requirements on the efficiency of air purification (removal of radioactive contaminants) and various requirements for the quality of air purification in the ventilation systems. Work performed at the Scientific Research Institute for Air Technology has resulted in filtration units of a universal modular type, the structural design of which permits a high degree of variation in their component parts. A brief description is given of the filtration units, their basic technical characteristics and examples of their use in nuclear power plant ventilation systems. (author)

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 5B. Experience data. Working material

International Nuclear Information System (INIS)

1996-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on the effects of Armenia earthquakes on selected power, industry and commercial facilities and seismic functional qualification of active mechanical and electrical components tested on shaking table

Different approaches to estimation of reactor pressure vessel material embrittlement

Directory of Open Access Journals (Sweden)

V. M. Revka

2013-03-01

Full Text Available The surveillance test data for the nuclear power plant which is under operation in Ukraine have been used to estimate WWER-1000 reactor pressure vessel (RPV material embrittlement. The beltline materials (base and weld metal were characterized using Charpy impact and fracture toughness test methods. The fracture toughness test data were analyzed according to the standard ASTM 1921-05. The pre-cracked Charpy specimens were tested to estimate a shift of reference temperature T0 due to neutron irradiation. The maximum shift of reference temperature T0 is 84 °C. A radiation embrittlement rate AF for the RPV material was estimated using fracture toughness test data. In addition the AF factor based on the Charpy curve shift (ΔTF has been evaluated. A comparison of the AF values estimated according to different approaches has shown there is a good agreement between the radiation shift of Charpy impact and fracture toughness curves for weld metal with high nickel content (1,88 % wt. Therefore Charpy impact test data can be successfully applied to estimate the fracture toughness curve shift and therefore embrittlement rate. Furthermore it was revealed that radiation embrittlement rate for weld metal is higher than predicted by a design relationship. The enhanced embrittlement is most probably related to simultaneously high nickel and high manganese content in weld metal.

Contemporary and prospective fuel cycles for WWER-440 based on new assemblies with higher uranium capacity and higher average fuel enrichment

International Nuclear Information System (INIS)

Gagarinskiy, A.A.; Saprykin, V.V.

2009-01-01

RRC 'Kurchatov Institute' has performed an extensive cycle of calculations intended to validate the opportunities of improving different fuel cycles for WWER-440 reactors. Works were performed to upgrade and improve WWER-440 fuel cycles on the basis of second-generation fuel assemblies allowing core thermal power to be uprated to 107 108 % of its nominal value (1375 MW), while maintaining the same fuel operation lifetime. Currently intensive work is underway to develop fuel cycles based on second-generation assemblies with higher fuel capacity and average fuel enrichment per assembly increased up to 4.87 % of U-235. Fuel capacity of second-generation assemblies was increased by means of eliminated central apertures of fuel pellets, and pellet diameter extended due to reduced fuel cladding thickness. This paper intends to summarize the results of works performed in the field of WWER-440 fuel cycle modernization, and to present yet unemployed opportunities and prospects of further improvement of WWER-440 neutronic and operating parameters by means of additional optimization of fuel assembly designs and fuel element arrangements applied. (Authors)

WWER nuclear waste management regulatory experience in Finland

International Nuclear Information System (INIS)

Varjoranta, Tero

2000-01-01

About 30% of all electricity produced in Finland is generated by nuclear power. Four reactors, with a total capacity of 2 656 MW e (net), are currently in operation. At Loviisa, there are two 488 MW e WWER units (recently upgraded 440-units) and at Olkiluoto two 840 MW e BWR units. At the Loviisa plant conditioning, storage and final disposal of low-and intermediate-level wastes from reactor operation will take place at the NPP sites. Intermediate level ion exchange resins and evaporation concentrates are currently stored in tanks. However, a license application for constructing a solidification plant based on cementation is currently under STUKs regulatory review. The construction of the final repository for I/LLW at the Loviisa site was started in 1993 and the Government granted the operating license in 1998. The nuclear legislation requires disposal of spent fuel into the Finnish bedrock. (Authors)

MOPABA-H2 - Computer code for calculation of hydrogen generation and distribution in the equipment of power plants with WWER type reactors in design modes of operation

International Nuclear Information System (INIS)

Arkhipov, O.P.; Kharitonov, Yu.V.; Shumskiy, A.M.; Kabakchi, S.A.

2002-01-01

With the aim of ensuring the hydrogen explosive-proof situation in the reactor plant, a complex of scientific-and-research work was carried out including the following: revealing the mechanisms of generation and release of hydrogen in the primary equipment components under design operation modes of the reactor plant with WWER; development of calculation procedure and computer code MOPABA-H2 enabling to determine the hydrogen content in RP equipment components under design operation modes. In the process of procedure development it was found out that the calculation of hydrogen content in the plant equipment requires development of the following main mathematical models: radiochemical processes in the primary coolant which has impurities and added special reagents; absorption of the core ionizing radiation by the coolant; steam-zirconium reaction (during design-basis accident of LOCA type); coolant mass transfer over the reactor plant equipment including transition of the phase boundary by the components of the coolant. (author)

Prospect of increases the efficiency of nuclear energy production in advanced light water reactors

International Nuclear Information System (INIS)

Proskuryakov, Konstantin; Belikov, Svyatoslav; Novikov, Konstantin

2011-01-01

Values of quality factor and pass-band for acoustic model of reactor core of reactor unit with WWER - 1000 are defined at single-phase and biphasic conditions of the coolant. The settlement-theoretical substantiation of conditions of growth of vibrations of internals and fuel assembly within a pass-band limits. Results of calculation and measurements have suitable coincidence. The technique of forecasting is developed and results of forecasting of vibration acoustical resonances of fuel assemblies with coolant in stationary and transitive operating modes of reactor unit with WWER - 1000 are worked out. (author)

Reactor pressure vessel status report

International Nuclear Information System (INIS)

Strosnider, J.; Wichman, K.; Elliot, B.

1994-12-01

This report gives a brief description of the reactor pressure vessel (RPV), followed by a discussion of the radiation embrittlement of RPV beltline materials and the two indicators for measuring embrittlement, the end-of-license (EOL) reference temperature and the EOL upper-shelf energy. It also summarizes the GL 92-01 effort and presents, for all 37 boiling water reactor plants and 74 pressurized water reactor plants in the United States, the current status of compliance with regulatory requirements related to ensuring RPV integrity. The staff has evaluated the material data needed to predict neutron embrittlement of the reactor vessel beltline materials. These data will be stored in a computer database entitled the reactor vessel integrity database (RVID). This database will be updated annually to reflect the changes made by the licensees in future submittals and will be used by the NRC staff to assess the issues related to vessel structural integrity

HEXTRAN-SMABRE calculation of the 6th AER Benchmark, main steam line break in a WWER-440 NPP

International Nuclear Information System (INIS)

Haemaelaeinen, A.; Kyrki-Rajamaeki, R.

2003-01-01

The sixth AER benchmark is the second AER benchmark for couplings of the thermal hydraulic codes and three dimensional neutron kinetic core models. It concerns a double end break of one main steam line in a WWER-440 plant. The core is at the end of its first cycle in full power conditions. In VTT HEXTRAN2.9 is used for the core kinetics and dynamics and SMABRE4.8 as a thermal hydraulic model for the primary and secondary loop. The plant model for SMABRE consists mainly of two input models, Loviisa model and a standard WWER-440/213 plant model. The primary loop includes six separate loops, the pressure vessel is divided into six parallel channels in SMABRE and the whole core calculation is performed in the core with HEXTRAN. The horizontal steam generators are modelled with heat transfer tubes in five levels and vertically with two parts, riser and downcomer. With this kind of detailed modelling of steam generators there occurs strong flashing after break opening. As a sequence of the main steam line break at nominal power level, the reactor trip is followed quite soon. The liquid temperature continues to decrease in one core inlet sector which may lead to recriticality and neuron power increase. The situation is very sensitive to small changes in the steam generator and break flow modelling and therefore several sensitivity calculations have been done. Also two stucked control rods have been assumed. Due to boric acid concentration in the high pressure safety injection subcriticality is finally guaranteed in the transient (Authors)

Computer analysis of elongation of the WWER fuel rod claddings

International Nuclear Information System (INIS)

Scheglov, A.; Proselkov, V.

2008-01-01

In this paper description of mechanisms influencing changes of the WWER fuel cladding length and axial forces influencing fuel and cladding are presented. It is shown that shortening of the fuel claddings in case of high burnup can be explained by the change of the fuel and cladding reference state caused by reduction of the fuel rod power level - during reactor outages. It is noted that the presented calculated data are to be reviewed and interpreted as the preliminary results; further work is needed for their confirmation. (authors)

Software in support of fuel operation in WWERS

International Nuclear Information System (INIS)

Evdokimov, I.A; Novikov, V.V; Ugrumov, A.V; Shishkin, A.A

2013-01-01

A software package comprising computer codes and fuel monitoring tools is under development in Russia in support of WWER fuel operation. The software package includes an expert computer system designed for failure diagnosis in course of reactor operation, prediction of activity evolution in primary coolant and express analysis of pellet-to-cladding mechanical interaction (PCMI) on rod-by-rod basis under normal and transient modes of operation. Coupled with the expert system, the first version of a graphical interface computer program is developed for NPP operating bodies. One of the features of this program is to launch automatically a fuel performance code for a series of detailed calculations for fuel rods with severe PCMI. The particular rods for calculations are determined by the expert system during the express core analysis. A greater attention is paid to recent results in prediction of fuel behavior after a primary failure has occurred. One of the major risks to further operation of leaking fuel comes from secondary fuel degradation due to massive cladding hydriding. Threshold conditions for initiation of secondary hydriding have been found on the basis of physical modeling. Final criteria of secondary failure occurrence were deduced by applying the model to analysis of post-irradiation examinations of leaking WWER fuel. (authors)

Experiences from start-up and use of fail-safe reactor level meter with KNITU probes

International Nuclear Information System (INIS)

Badiar, S.; Sipka, J.; Vanco, P.; Slanina, Marek; Liska, L.; Gavora, D.

2001-01-01

Within the framework of the reconstruction of both V1 Bohunice units with WWER-440/V-230 reactors, the VUJE-SIEMENS consortium implemented measurement systems for coolant level monitoring in reactor pressure vessels with 1E qualification, resp. with the qualification of category 1 according to NUSS RG1.97. The solution uses KNITU 11 probes made by Russian POZIT company. In operating plants, the installation causes problems in relation to the existing technology and quality assurance system. In the phase of implementation, the most important tasks were to resolve component quality, to commission the system, and to check its performance. (Authors)

Pressure tube reactors

International Nuclear Information System (INIS)

Natori, Hisahide.

1981-01-01

Purpose: To improve the electrical power generation efficiency in a pressure tube reactor in which coolants and moderators are separated by feedwater heating with heat generated in heavy water and by decreasing the amount of steams to be extracted from the turbine. Constitution: A heat exchanger and a heavy water cooler are additionally provided to a conventional pressure tube reactor. The heat exchanger is disposed at the pre-stage of a low pressure feedwater heater series. High temperature heavy water heated in the core is passed through the primary side of the exchanger, while feedwater is passed through the secondary side. The cooler is disposed on the downstream of the heat exchanger in the flowing direction of the heavy water, in which heavy water from the heat exchanger is passed through the primary side and the auxiliary equipment cooling water is sent to the secondary side thereof. Accordingly, since extraction of heating steams is no more necessary, the steam can be used for the rotation of the turbine, and the electrical power generation efficiency can be improved. (Seki, T.)

System for step-wise accident protection of nuclear reactors

International Nuclear Information System (INIS)

Rubek, J.; Kuklik, B.; Bednarik, K.

1991-01-01

A system comprising electric switching circuits is proposed for the control of a WWER type reactor shutdown in case of turbine failure or another abnormal situation. The fastest reactor shutdown mode is only resorted to if the pressures in the primary and secondary circuits would otherwise increase above tolerable limits and safety valves would open. The temperature and pressure stress of the nuclear power plant components and fuel is reduced. In this manner, the losses emerging during turbine failures due to false alarms are minimized. The contacts of the system switch if the turbines are relieved to the power of the unit home consumption, if the first or second turbine fails by closing the quick-acting valves, if a signal for blocking the by-pass stations of the operated turbines appears, or if the electric supply of the control system and of the turbo-set protection fails. (M.D.). 1 fig

Q-factor of coolant flow in the primary circuit of NPP with pressurised water reactors

International Nuclear Information System (INIS)

Proskuryakov, K.N.; Belikov, S.O.; Novikov, K.S.

2011-01-01

Systems of preoperational vibration dynamic monitoring in of WWER are presented. The results of measurements during commission of NPP with WWER are presented. The paper provides the result of the research, that estimation of coolant fluctuations caused by pulse perturbation of pressure in the primary circuit NPP. It is shown that results could be received at known value of a Q - factor of acoustical oscillatory system only. The research demonstrates the results of dependence of the sound speed from the mass steam content in the coolant flow thru reactor core. The worked out results can be used for identification of the reasons of abnormal growth of level of vibrations of fuel assembly, fuel rod, equipment and internals, and for forecasting the operation conditions which provide of vibration - acoustical resonances in the primary loop equipment. (author)

Reactor safety in Eastern Europe. Proceedings

International Nuclear Information System (INIS)

1995-02-01

The papers presented to the GRS colloquium refer to the cooperative activities for reactor accident analysis and modification of the GRS computer codes for their application to reactors of the Russian design types of WWER or RBMK. Another topic is the safety of RBMK reactors in particular, and the current status of investigations and studies addressing the containment of unit 4 of the Chernobyl reactor station. (HP) [de

Pressure tube reactor

International Nuclear Information System (INIS)

Matsumoto, Tomoyuki; Fujino, Michihira.

1980-01-01

Purpose: To equalize heavy water flow distribution by providing a nozzle for externally injecting heavy water from a vibration preventive plate to the upper portion to feed the heavy water in a pressure tube reactor and swallowing up heavy water in a calandria tank to supply the heavy water to the reactor core above the vibration preventive plate. Constitution: A moderator injection nozzle is mounted on the inner wall of a calandria tank. Heavy water is externally injected above the vibration preventive plate, and heavy water in the calandria tank is swallowed up to supply the heavy water to the core reactor above the vibration preventive plate. Therefore, the heavy water flow distribution can be equalized over the entire reactor core, and the distribution of neutron absorber dissolved in the heavy water is equalized. (Yoshihara, H.)

Fuel element cladding state change mathematical model for a WWER-1000 plant operated in the mode of varying loading

Directory of Open Access Journals (Sweden)

S. N. Pelykh

2010-09-01

Full Text Available Main features of a fuel element cladding state change mathematical model for a WWER-1000 reactor plant operated in the mode of varying loading are listed. The integrated model is based on the energy creep theory, uses the finite element method for imultaneous solution of the fuel element heat conduction and mechanical deformation equa-tions. Proposed mathematical model allows us to determine the influence of the WWER-1000 regime parameters and fuel assembly design characteristics on the change of cladding properties under different loading conditions of normal operation, as well as the cladding limiting state at variable loading depending on the length, depth and number of cycles.

Developing new calculational and experimental techniques for studying the WWER reactor cores and characteristics

International Nuclear Information System (INIS)

Zakharko, Yu.A.; Proshkin, A.A.

1986-01-01

Necessity of analytical approaches alongside with existing numerical methods of fuel element calculation is discussed. Analytical solutions of viscoelastic equations describing mechanical fuel-cladding interaction have been obtained. At that universal temperature dependence of creep characteristics is suggested. Dependence of behaviour of the WWER fuel element fuel and cladding on absolute temperature level and gradients is analysed

WWER Steam Generators Tubing Performance and Aging Management

International Nuclear Information System (INIS)

Trunov, Nikolay B.; Davidenko, Stanislav E.; Grigoriev, Vladimir A.; Popadchuk, Valery S.; Brykov, Sergery I.; Karzov, Georgy P.

2006-01-01

At WWER NPPs the horizontal steam generators (SGs), are used that differ in design concept from vertical SGs mostly used at western NPPs. Reliable operation of SG heat-exchanging tubes is the crucial worldwide problem for NPP of various types. According to the operation feedback the water chemistry is the governing factor affecting operability of SG tubing. The secondary side corrosion is considered to be the main mechanism of SG heat-exchanging tubes damage at WWER plants. To make the assessment of the tubing integrity the combination of pressure tests and eddy-current tests is used. Assessment of the tubing performance is an important part of SG life extension practice. The given paper deals with the description of the tube testing strategy and the approach to tube integrity assessment based on deterministic and probabilistic methods of fracture mechanics. Requirements for eddy-current test are given as well. Practice of condition monitoring and implementing the database on steam generators operation are presented. The approach to tubes plugging criteria is described. The research activities on corrosion mechanism studies and residual lifetime evaluation are mentioned. (authors)

Modernization in-core monitoring system, of WWER-1000 reactors (W-320) by fuel assemblies with individual characteristics using

International Nuclear Information System (INIS)

Mitin, V. I.; Semchenkov, J. M.; Kalinushkin, A. E.

2007-01-01

The present report covers object, conception, engineering solution of construction of modern system of high-powered reactor in-core control, including WWER-1000 (V-320) reactors. It is known that ICMS main task is on-line monitoring distribution of power release field and its functioning independently of design programs to avoid common reason error. It is shown in what way field of power release recovery has been carrying on; rest on the signals of in-core neutron and temperature sensors. On the base of the obtained and refined information there have being automatically generated signals of preventive and emergency protection on local parameters (linear power to the maximum intensive fuel elements, reserve to heat exchange crisis, 'picking factor'). There have represented technology on sensors and processing methods of SPND and TC signals, ICIS composition and structure, program hard ware, system and applied software. Structure, composition and the taken decisions allow combining class 1E and class B and C tasks in accordance with international norms of separation and safety classes' realization. At present ICIS-M is a system, providing implementation of control, safety, information and diagnostic functions, which allow securing actual increase of quality, reliability and safety in operation of nuclear fuel and NPP units. And at the same time it reduces human factor negative influence to core work thermo technical eliability in the operational process (Authors)

Reactor safety in Eastern Europe

International Nuclear Information System (INIS)

1995-02-01

The papers presented to the GRS colloquium refer to the cooperative activities for reactor accident analysis and modification of the GRS computer codes for their application to reactors of the Russian design types of WWER or RBMK. Another topic is the safety of RBMK reactors in particular, and the current status of investigations and studies addressing the containment of unit 4 of the Chernobyl reactor station. All papers are indexed separately in report GRS--117. (HP)

Primary Damage Characteristics in Metals Under Irradiation in the Cores of Thermal and Fast Reactors

International Nuclear Information System (INIS)

Pechenkin, V.A.

2012-01-01

For an analysis and forecasting of radiation-induced phenomena in structural materials of WWERs, PWRs and BN reactors the fast neutron fluence is usually used (for structural materials of the reactor cores and internals the fluence of neutrons with energy > 0.1 MeV, for WWER and PWRs vessel steels the fluence of neutrons with energy > 0.5 MeV in Russia and East Europe, and with energy > 1.0 MeV in USA and France). Displacements per atom (dpa) seem to be a more appropriate correlation parameter, because it allows comparing the results of materials irradiation in different neutron energy spectra or with different types of particles (neutrons, ions, fast electrons). Energy spectra of primary knocked atoms (PKA) and 'effective' dpa, which are introduced to take into account the point defect recombination during the relaxation stage of a displacement cascade, can be still better representation of the effect of irradiation on material properties. In this work the results of calculating dose rates (dpa/s, NRT-model), PKA energy spectra and PKA mean energies in metals under irradiation in the cores of Russian reactors WWER-440, WWER-1000 (both power thermal reactors) and BN-600 (power fast reactor) and BR-10 (test fast reactor) are presented. In all the reactors Fe and Zr are considered, with addition of Ti and W in BN-600. 'Effective' dose rates in these metals are calculated. Limitations and uncertainties in the standard dpa formulation (the NRT-dpa) are discussed. IPPE activities in the fields related to the TM subject are considered

Designing a nuclear power plant with 1000 MW WWER-type units

Energy Technology Data Exchange (ETDEWEB)

Berkovich, V; Kaloshin, J; Tatarnikov, V; Shenderovich, A

1977-06-01

A brief description is presented of a WWER-1000 nuclear power plant also considering its environmental impact and the problem of core poisoning. The following indicators are graphically shown in relation to the reactor output: turbogenerator unit outputs, efficiency, specific capital costs and own costs of electric power generated by the Voronezh nuclear power plant. Also listed are the specific consumption of metal and concrete, specific equipment weight and the specific volume of the buildings of the main generating unit as well as the cross section thereof.

Electrode for welding steel for WWER-1000 reactor pressure vessel

International Nuclear Information System (INIS)

Lakatos, L.

Of two types of electrodes, ie., with an alloyed core and with an unalloyed core, an electrode was chosen consisting of a basic coat and an unalloyed core. Fluctuations are shown of shear strength, tensile strenght and contraction with the welding mode and annealing temperature. It was found that pre-heating to 250 and 350 degC, respectively, was most suitable for welding a pressure vessel manufactured from material designated SKODA A3/II. Annealing aimed at removing stress was chosen at 650 to 700 degC. (H.S.)

'AER Working Group D On WWER Safety Analysis' Report Of The Meeting In Pisa, Italy, 26-27 April 2006

International Nuclear Information System (INIS)

Siltanen, P.

2006-01-01

AER Working Group D on WWER reactor safety analysis held its 15 t h meeting in Grand Hotel Duomo in Pisa, Italy during the period 26-27 April 2006. The meeting was hosted by the University of Pisa following the fourth workshop on the OECD/DOE/CEA WWER-1000 Coolant Transient Benchmark (W1000-CT) held at the same location on 24-25 April. Altogether 15 participants attended the Working Group D meeting, 11 from AER member organizations and 4 guests from non-member organizations. The coordinator for the working group, Mr. P. Siltanen (FNS) served as chairman. In addition to general information exchange on recent activities in the participating organizations, the topics of the meeting included: 1) Code development and benchmarking for reactor dynamics applications. 2) Safety analysis methodology and results. 3) Future activities. A list of participants and a list of handouts distributed at the meeting are attached to the report (Author)

Results of reactor pressure vessels ISI

International Nuclear Information System (INIS)

Cepcek, S.

1994-01-01

To find out the possible influence of the annealing process to reactor pressure vessel integrity, a large in-service inspection programme has been implemented as an associated activity to reactor pressure vessel annealing. In this paper the approach to the RPV in-service inspection is shown. Also, the main results and conclusions following in-service inspection are presented. (author). 3 refs, 1 fig

Co-ordinated research programme on benchmark study for the seismic analysis and testing of WWER-type nuclear power plants. V. 4B. Paks NPP: Analysis/testing. Working material

International Nuclear Information System (INIS)

1995-01-01

The Co-ordinated research programme on the benchmark study for the seismic analysis and testing of WWER-type nuclear power plants was initiated subsequent to the request from representatives of Member States. The conclusions adopted at the Technical Committee Meeting on Seismic Issues related to existing nuclear power plants held in Tokyo in 1991 called for the harmonization of methods and criteria used in Member States in issues related to seismic safety. The Consulltants' Meeting which followed resulted in producing a working document for CRP. It was decided that a benchmark study is the most effective way to achieve the principal objective. Two types of WWER reactors (WWER-440/213 and WWER-1000) were selected as prototypes for the benchmark exercise to be tested on a full scale using explosions and/or vibration generators. The two prototypes are Kozloduy Units 5/6 for WWER-1000 and Paks for WWER-440/213 nuclear power plants. This volume of Working material contains reports on dynamic study of the main building of the Paks NPP; shake table investigation at Paks NPP and the Final report of the Co-ordinated Research Programme

Study of susceptibility to hydrogen embrittlement of welded joints of large WWER reactor vessels at different temperatures

International Nuclear Information System (INIS)

Mazel', R.E.; Kuznetsova, T.P.; Grinenko, V.G.; Sapronova, M.N.

1977-01-01

The effect is studied of hydrogen and a coolant of WWER on the susceptibility to brittle fracture of welded joints from steels 15Kh2MFA and 15Kh2NMFA obtained by automatic submerged arc welding with the use of the welding materials of different purity. The effect of hydrogen (concentration range 0.5-7.5 cm 3 /100 g, testing temperatures 20, 70 and 325 deg C) and the coolant (pressures up to 120 atm, temperatures 20-350 deg C) have been estimated by the fracture work during static bending tests. It is shown that the purification of the welding materials enhances the fracture properties by about a factor of 2. Hydrogenation results in a sharp drop (by about a factor of 3) of the fracture work. The increased testing temperature (up to 325 deg C) is accompanied by disappearance of the effect of hydrogen embrittlement, which is explained by an increase in the diffusion mobility of atomic hydrogen. Under the action of the coolant the fracture work shows a two-fold decrease, while the pressure being increased up to 100 atm leads to greater fracture work decrease

Automatized welding equipment for manufacturing steel cells for special buildings

International Nuclear Information System (INIS)

Weikert, F.; Winter, K.P.

1986-01-01

In GDR's nuclear power plant construction, reinforced concrete wall cells are used to construct pressure and full pressure containments for WWER-440 and WWER-1000 reactors, respectively. Welding processes for the prefabrication of steel cells as reinforcement have been automatized in order to increase both labor productivity and quality assurance. 11 figs

Computerized reactor pressure vessel materials information system

International Nuclear Information System (INIS)

Strosnider, J.; Monserrate, C.; Kenworthy, L.D.; Tether, C.D.

1980-10-01

A computerized information system for storage and retrieval of reactor pressure vessel materials data was established, as part of Task Action Plan A-11, Reactor Vessel Materials Toughness. Data stored in the system are necessary for evaluating the resistance of reactor pressure vessels to flaw-induced fracture. This report includes (1) a description of the information system; (2) guidance on accessing the system; and (3) a user's manual for the system

Calibration of the enigma code for Finnish reactor fuel with support from experimental irradiations

Energy Technology Data Exchange (ETDEWEB)

Kelppe, S; Ranta-Puska, K [VTT Energy, Jyvaeskylae (Finland)

1997-08-01

Assessment by VTT of the ENIGMA fuel performance code, the original version by Nuclear Electric plc of the UK amended by a set of WWER specific materials correlations, is described. The given examples of results include analyses for BWR 9 x 9 fuel, BWR fuel irradiated in the reinstrumented test of an international Riso project, pre-characterized commercial WWER fuel irradiated in Loviisa reactor in Finland, and instrumented WWER test fuel irradiations in the MR reactor in Russia. The effects of power uncertainty and some model parameters are discussed. Considering the fact that the described cases all mean prototypic application of the code, the results are well encouraging. The importance of the accuracy in temperature calculations is emphasized. (author). 2 refs, 12 figs, 1 tab.

State space modeling of reactor core in a pressurized water reactor

Energy Technology Data Exchange (ETDEWEB)

Ashaari, A.; Ahmad, T.; M, Wan Munirah W. [Department of Mathematical Science, Faculty of Science, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Shamsuddin, Mustaffa [Institute of Ibnu Sina, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Abdullah, M. Adib [Swinburne University of Technology, Faculty of Engineering, Computing and Science, Jalan Simpang Tiga, 93350 Kuching, Sarawak (Malaysia)

2014-07-10

The power control system of a nuclear reactor is the key system that ensures a safe operation for a nuclear power plant. However, a mathematical model of a nuclear power plant is in the form of nonlinear process and time dependent that give very hard to be described. One of the important components of a Pressurized Water Reactor is the Reactor core. The aim of this study is to analyze the performance of power produced from a reactor core using temperature of the moderator as an input. Mathematical representation of the state space model of the reactor core control system is presented and analyzed in this paper. The data and parameters are taken from a real time VVER-type Pressurized Water Reactor and will be verified using Matlab and Simulink. Based on the simulation conducted, the results show that the temperature of the moderator plays an important role in determining the power of reactor core.

Experimental support of WWER-440 fuel reliability and serviceability at high burnup

Energy Technology Data Exchange (ETDEWEB)

Smirnov, A; Ivanov, V; Pnyushkin, A [Nauchno-Issledovatel` skij Inst. Atomnykh Reaktorov, Dimitrovgrad (Russian Federation); Tzibulya, V [AO Mashinostroitelnij Zavod Electrostal (Russian Federation); Kolosovsky, V; Bibilashvili, Yu [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation); Dubrovin, K [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)

1994-12-31

Results from post-reactor examination of two WWER-440 fuel assemblies spent at the Kola NPP Unit 3 during 4 and 5 fuel cycles are presented. The fuel assembly states and their serviceability allowance are estimated experimentally at the RIAR hot laboratory and studied by non-destructive and destructive methods. The following parameters are examined: fuel assembly overall dimensions change; fuel element diameter change; fuel element cladding corrosion and hydriding; fuel element cladding mechanical properties; fission gas release from fuel and gas pressure; fuel macro- and microstructure. it has been found that the maximum fuel burnup of fuel assemblies No. 1 and No.2 achieved is 58.3 and 64.0 MWd/kg, respectively. The mechanical fuel pellets-cladding interaction has been observed at the average fuel burnup above 45 MWd/kg that occurred with increasing the local cladding diameter at the areas of pellets end arrangement (bamboo stick). The gas release linearly increases at the range 2.7% per 10 MWd/kg within burnup of 43-60 MWd/kg. 9 figs., 3 refs.

Calculation of isotope burn-up and change in efficiency of absorbing elements of WWER-1000 control and protection system during burn-up

International Nuclear Information System (INIS)

Timofeeva, O.A.; Kurakin, K.U.

2006-01-01

The report deals with fast and thermal neutron flows distribution in structural elements of WWER-1000 fuel assembly and absorbing rods, determination of absorbing isotope burn-up and worth variation in WWER reactor control and protection system rods. Simulation of absorber rod burn-up is provided using code package SAPPHIRE 9 5 end RC W WER allowing detailed description of the core segment spatial model. Maximum burn-up of absorbing rods and respective worth variation of control and protection system rods is determined on the basis of a number of calculations considering known characteristics of fuel cycles (Authors)

Designing a nuclear power plant with 1000 MW WWER-type units