Evaluation of Pulp and Paper Properties obtained from Maple Juvenile Wood through Organosolv Alcohol Method Catalyzed by Calcium and Magnesium Salts

Directory of Open Access Journals (Sweden)

Reza Naghdi

2015-05-01

Full Text Available The properties of catalyzed organosolv pulp obtained from maple juvenile wood were studied. The physical properties of fiber (e.g. length, width, and cell membrane thickness and chemical composition of maple juvenile wood (e.g. average cellulose, lignin, extractives, and ash content were determined. The variables were cooking temperature (190 and 200 ºC and time (40, 60, and 80 minutes. Chemical charge ( 280 ml methanol, 70 ml water, and 0.025 mols of Calcium Chloride and Magnesium Nitrate was kept constant. Pulp screen yields (54.9 to 60.91% and Kappa No. (15.5 to 18.4 were measured. Pulp freeness was reduced to 350 ml CSF in PFI mill, and ten 60 g/m2 handsheets were made from the selected pulps. The strength properties of catalyzed organosolv handsheets including tear length (3.83 to 4.25 km, tear index (10.22 to 12.81 mN.m2/g, and burst index (1.74 to 2.15 kPa.m2/g were compared with those of the conventional Kraft handsheets of maple juvenile wood. The least allowed values of the mentioned properties in the Indian (IS and Japanese international standards (JIS reveal that while the tear length value is slightly below that of the standards, the values of tear and burst indices are well beyond the given standards, and the environmentally-friendly catalyzed organosolv pulping process (higher yield and lower Kappa No. compared to Kraft can be recommended to produce paper pulp from maple juvenile wood.

The effects of high energy radiation on the pulping properties of Pinus radiation and Eucalyptus regnans

International Nuclear Information System (INIS)

McLaren, K.G.; Garland, C.P.; Higgins, H.G.

1976-01-01

Studies have been made of the effects of high energy radiation on the pulping behaviour of Eucalyptus regnans and Pinus radiata. Pre-irradiation of wood chips with small doses of 60 Co gamma radiation (up to about 0.2 Mrad) caused little degradation of the cellulose, and had only minor effects on the kraft pulping properties of both wood species. Pulp yield, Kappa number and strength properties of the pulps showed little change. There was also little effect on the bisulphite cooking of Pinus radiata. As the dose was increased to 1 Mrad, degradation of cellulose (as indicated by degree of polymerisation measurements) became significant, and Kraft pulp yields from both woods showed small reductions. The Kappa number and physical properties of these pulps were little affected at this dose level. A gamma radiation dose of 10 Mrad produced marked depolymerisation of the cellulose, and big reductions in kraft and neutral sulphite semi-chemical pulp yields. The kraft pulps showed a much higher lignin content. Some low dose (0.15 Mrad) irradiations on thin chips were carried out with a 1 MeV electron accelerator. In contrast to comparable gamma irradiations, this treatment produced discernible changes in kraft pulping behaviour. The pulp yield, under the same cooking conditions, appears to be slightly higher, but the Lignin content of the pulp was increased. (Author)

Acid bi-sulphite pulping effects on hardwoods and a softwood revealed by atomic force microscopy

CSIR Research Space (South Africa)

Chunilall, Viren

2009-12-01

Full Text Available Wood fibres are the raw material used in the production of dissolving pulp for the manufacture of cellulose derivatives such as viscose and cellulose acetate. At the microscopic level, the wood cell wall is organised in layers with different...

Nanofibrillated cellulose as paper additive in Eucalyptus pulps

Directory of Open Access Journals (Sweden)

Israel González

2012-11-01

Full Text Available In this work, the physical and mechanical properties of bleached Eucalyptus pulp reinforced with nanofibrillated cellulose (NFC are compared with those of traditional beaten pulp used in the making of writing/printing and offset printing papers. For this purpose, three different types of hardwood slurries were prepared: beaten pulps, unbeaten pulps reinforced with NFC, and slightly beaten pulps also reinforced with NFC. Physical and mechanical tests were performed on handsheets from these different slurries. The results showed that adding NFC to unbeaten pulps results in physical and mechanical properties similar to those in pulps used for printing/writing papers. Nevertheless, the best results were obtained in slurries previously beaten at slight conditions and subsequently reinforced with NFC. These results demonstrate that the addition of NFC allows a reduction in beating intensity without decreasing the desired mechanical properties for this specific purpose.

Overview of Cellulose Nanomaterials, Their Capabilities and Applications

Science.gov (United States)

Robert J. Moon; Gregory T. Schueneman; John Simonsen

2016-01-01

Cellulose nanomaterials (CNs) are a new class of cellulose particles with properties and functionalities distinct from molecular cellulose and wood pulp, and as a result, they are being developed for applications that were once thought impossible for cellulosic materials. Momentum is growing in CN research and development, and commercialization in this field is...

Cellulose-hemicellulose interaction in wood secondary cell-wall

International Nuclear Information System (INIS)

Zhang, Ning; Li, Shi; Hong, Yu; Chen, Youping; Xiong, Liming

2015-01-01

The wood cell wall features a tough and relatively rigid fiber reinforced composite structure. It acts as a pressure vessel, offering protection against mechanical stress. Cellulose microfibrils, hemicellulose and amorphous lignin are the three major components of wood. The structure of secondary cell wall could be imagined as the same as reinforced concrete, in which cellulose microfibrils acts as reinforcing steel bar and hemicellulose-lignin matrices act as the concrete. Therefore, the interface between cellulose and hemicellulose/lignin plays a significant role in determine the mechanical behavior of wood secondary cell wall. To this end, we present a molecular dynamics (MD) simulation study attempting to quantify the strength of the interface between cellulose microfibrils and hemicellulose. Since hemicellulose binds with adjacent cellulose microfibrils in various patterns, the atomistic models of hemicellulose-cellulose composites with three typical binding modes, i.e. bridge, loop and random binding modes are constructed. The effect of the shape of hemicellulose chain on the strength of hemicellulose-cellulose composites under shear loadings is investigated. The contact area as well as hydrogen bonds between cellulose and hemicellulose, together with the covalent bonds in backbone of hemicellulose chain are found to be the controlling parameters which determine the strength of the interfaces in the composite system. For the bridge binding model, the effect of shear loading direction on the strength of the cellulose material is also studied. The obtained results suggest that the shear strength of wood-inspired engineering composites can be optimized through maximizing the formations of the contributing hydrogen bonds between cellulose and hemicellulose. (paper)

Cellulose-hemicellulose interaction in wood secondary cell-wall

Science.gov (United States)

Zhang, Ning; Li, Shi; Xiong, Liming; Hong, Yu; Chen, Youping

2015-12-01

The wood cell wall features a tough and relatively rigid fiber reinforced composite structure. It acts as a pressure vessel, offering protection against mechanical stress. Cellulose microfibrils, hemicellulose and amorphous lignin are the three major components of wood. The structure of secondary cell wall could be imagined as the same as reinforced concrete, in which cellulose microfibrils acts as reinforcing steel bar and hemicellulose-lignin matrices act as the concrete. Therefore, the interface between cellulose and hemicellulose/lignin plays a significant role in determine the mechanical behavior of wood secondary cell wall. To this end, we present a molecular dynamics (MD) simulation study attempting to quantify the strength of the interface between cellulose microfibrils and hemicellulose. Since hemicellulose binds with adjacent cellulose microfibrils in various patterns, the atomistic models of hemicellulose-cellulose composites with three typical binding modes, i.e. bridge, loop and random binding modes are constructed. The effect of the shape of hemicellulose chain on the strength of hemicellulose-cellulose composites under shear loadings is investigated. The contact area as well as hydrogen bonds between cellulose and hemicellulose, together with the covalent bonds in backbone of hemicellulose chain are found to be the controlling parameters which determine the strength of the interfaces in the composite system. For the bridge binding model, the effect of shear loading direction on the strength of the cellulose material is also studied. The obtained results suggest that the shear strength of wood-inspired engineering composites can be optimized through maximizing the formations of the contributing hydrogen bonds between cellulose and hemicellulose.

Integrated production of wood fuel and pulp wood from young stands; Integroitujen tuotantomenetelmien vertailu

Energy Technology Data Exchange (ETDEWEB)

Korpilahti, A [Metsaeteho Oy, Helsinki (Finland)

1997-12-01

The aim of the study was to clarify the competitiveness of different harvesting chains and processing methods of first thinning wood. Great expectations have been laid on integrated production of wood fuel and pulp wood. Results produced in other bioenergy projects were taken into account, and in this project some field experiments on mechanised felling-bunching and compressing of the load of tree sections during forwarding were carried out. The new processing methods, the MASSAHAKE-method and chain-flail delimbing combined with small-scale drum debarking, still are under development giving a rather unstable data for comparisons. Both in pine and birch dominant stands modern multiple tree logging gave the most favourable results when ranking on the bases of the price of pulp chips. Integrated methods were not very far and they have more potential than methods based on harvesting delimbed short wood. When compared on the bases of the production cost of pulp, integrated methods were in general the most favourable because they give good subsidies on the form of bioenergy. (orig.)

Cellulosic pulps of cereal straws as raw material for the manufacture of ecological packaging

OpenAIRE

Vargas González, Fátima; González, Zoilo; Sánchez, Rafael; Jiménez, Luis; Rodríguez Pascual, Alejandro

2012-01-01

The aim of this work was to study the potential application of four types of cereal straws: oats, maize, rapeseed, and barley, in order to obtain cellulose pulp through the Specel® process for use in the manufacture of 100% biodegradable and ecological packaging. Raw materials were chemically characterized to determine alcohol-extractives, ash, lignin, holocellulose, and α-cellulose. Cellulosic pulps obtained from raw materials were characterized to determine yield, Kappa number, and viscosit...

EFFECT OF LIGNIN CONTENT OF Eucalyptus globulus WOOD IN KRAFT PULPING PERFORMANCE

Directory of Open Access Journals (Sweden)

Gabriel Valim Cardoso

2011-03-01

Full Text Available In this research, it was analyzed the lignin content effect of Eucalyptus globulus wood in kraft pulping optimization. Seventy-two laboratory cooking were made with wood chips obtained from six Eucalyptus globulus trees selected from a group of 50 trees. The wood chips from three trees with the lowest lignin content, with average 20,53%, were mixed proportionally based on the tree weights, obtaining the sample of low lignin content wood. The same was made to obtain the sample for wood chips with the highest lignin content, with average 23,02%. The two lignin levels were statistically different. The two wood samples had basic densities statistically not different. Using three maximum temperatures levels (160, 165 and 170ºC, and three active alkali charged (17, 18,5 and 20%, the wood chips were converted to kraft pulps. The pulps were then characterized to analyze the influence of the distinct treatments employed in the cooking on their properties. The effect of the cooking conditions was expressed by mathematical models in order to determine the optimum points for each of the evaluated properties. The optimization process indicated maximum temperature of 168ºC, and active alkali of 19%, for maximum kraft pulping yield to achieve kappa number 18; this result was for woods with low lignin content. For woods containing the high lignin content, the optimization showed maximum cooking temperature of 169ºC and active alkali of 19% for kappa number of 18. The average reduction of 2,49% in wood lignin content resulted a correspondent gain of 2,2% in the kraft yield (o.d. basis and a reduction on the active alkali charge of 1,2% (o.d. basis to achieve kappa numbers from 16 to 19, preserving pulp properties. If the option is to work with kappa number 19 instead of 16, the gain in kraft yield is approximately 2%. Therefore, when working with low lignin content wood and kappa number 19 instead of 16, a substantial gain of approximately 4,2% is obtained

Method for improving separation of carbohydrates from wood pulping and wood or biomass hydrolysis liquors

Science.gov (United States)

Griffith, William Louis; Compere, Alicia Lucille; Leitten, Jr., Carl Frederick

2010-04-20

A method for separating carbohydrates from pulping liquors includes the steps of providing a wood pulping or wood or biomass hydrolysis pulping liquor having lignin therein, and mixing the liquor with an acid or a gas which forms an acid upon contact with water to initiate precipitation of carbohydrate to begin formation of a precipitate. During precipitation, at least one long chain carboxylated carbohydrate and at least one cationic polymer, such as a polyamine or polyimine are added, wherein the precipitate aggregates into larger precipitate structures. Carbohydrate gel precipitates are then selectively removed from the larger precipitate structures. The method process yields both a carbohydrate precipitate and a high purity lignin.

Enzymatically-Mediated Co-Production of Cellulose Nanocrystals and Fermentable Sugars

Directory of Open Access Journals (Sweden)

Dawit Beyene

2017-10-01

Full Text Available Cellulose nanocrystals (CNCs can be extracted from cellulosic materials through the degradation of non-crystalline cellulose domains in the feedstock via acid hydrolysis. However, the sugars released from the hydrolysis process cannot be easily recovered from the acid waste stream. In this study, cellulases were used to preferentially degrade non-crystalline domains with the objectives of recovering sugars and generating a feedstock with concentrated CNC precursors for a more efficient acid hydrolysis process. Filter paper and wood pulp substrates were enzyme-treated for 2–10 h to recover 20–40 wt % glucose. Substantial xylose yield (6–12 wt % was generated from wood pulp. CNC yields from acid hydrolysis of cellulases-treated filter paper, and wood pulp improved by 8–18% and 58–86%, respectively, when compared with the original substrate. It was thought that CNC precursors accumulated in the cellulases-treated feedstock due to enzymatic digestion of the more accessible non-crystalline celluloses. Therefore, acid hydrolysis from enzyme-treated feedstock will require proportionally less water and reagents resulting in increased efficiency and productivity in downstream processes. This study demonstrates that an enzymatically-mediated process allows recovery of fermentable sugars and improves acid hydrolysis efficiency for CNC production.

Chemi-thermomechanical pulping of para rubber waste wood

Energy Technology Data Exchange (ETDEWEB)

Kubo, T.; Hosokawa, J.; Kobayashi, T.; Kobayashi, Y.

1981-01-01

The addition of NaOH to Na/sub 2/SO/sub 3/-treated waste wood chips (Hevea brasiliensis) increased long fiber fraction, Klason lignin content and bulk density, improved breaking length and tear factor, and decreased energy consumption in refining and brightness of resulting chemithermomechanical pulp. Lowering in brightness by alkali treatment was recovered by H/sub 2/O/sub 2/ bleaching, and bleaching with 8% H/sub 2/O/sub 2/ on pulp gave pulp with 61.3% brightness.

Electron treatment of wood pulp for the viscose process

Science.gov (United States)

Stepanik, T. M.; Ewing, D. E.; Whitehouse, R.

2000-03-01

Electron processing is currently being evaluated by several viscose producers for integration into their process. The viscose industry converts dissolving wood pulp into products such as staple fibre, filament, cord, film, packaging, and non-edible sausage casings. These materials are used in the clothing, drapery, hygiene, automobile, food, and packaging industries. Viscose producers are facing increasingly high production costs and stringent environmental regulations that have forced some plants to close. Electron treatment of wood pulp can significantly reduce the amounts of chemicals used for producing viscose and the production of hazardous pollutants. Acsion Industries has worked with companies worldwide to demonstrate the benefits of using electron treated pulp for producing viscose (rayon). This paper describes the viscose process, the benefits of using electron treatment in the viscose process, and Acsion's efforts in developing this technology.

Nanoreinforced biocompatible hydrogels from wood hemicelluloses and cellulose whiskers

Science.gov (United States)

Muzaffer Ahmet Karaaslan; Mandla A. Tshabalala; Daniel J. Yelle; Gisela Buschle-Diller

2011-01-01

Nanoreinforced hydrogels with a unique network structure were prepared from wood cellulose whiskers coated with chemically modified wood hemicelluloses. The hemicelluloses were modified with 2-hydroxyethylmethacrylate prior to adsorption onto the cellulose whiskers in aqueous medium. Synthesis of the hydrogels was accomplished by in situ radical polymerization of the...

Effect of raw wood supply system on the wood paying capability of a kraft pulp mill using Scots pine

Energy Technology Data Exchange (ETDEWEB)

Dahl, O. (Helsinki Univ. of Technology, Espoo (Finland), Dept. of Forest Products Technology), Email: olli.dahl@tkk.fi; Jylhae, P. (Finnish Forest Research Inst., Kannus (Finland)), Email: paula.jylha@metla.fi; Laitila, J. (Finnish Forest Research Inst., Joensuu (Finland)), Email: juha.laitila@metla.fi; Kaerhae, K. (Metsaeteho Oy, Helsinki (Finland)), Email: kalle.karha@metsateho.fi

2009-07-01

Integration of energy wood procurement into that of pulpwood is seen as a means for reducing the high procurement costs of small-diameter wood harvested from first thinnings. In the deepest mode of integration, pulp and energy fractions are separated from each other in the debarking drum of the pulp mill. In the present paper, the competitiveness of the conventional supply chain based on cut-to-length harvesting was compared to the supply systems based on the harvesting of loose whole trees and whole-tree bundling, in the cases of three Scots pine-dominated first-thinning stands using wood paying capability (WPC) of a kraft pulp mill as a decisive criterion. Furthermore, the competitiveness of first thinnings as raw material sources for a pulp mill was evaluated by using intermediate thinnings as s reference. (orig.)

Cellulose Nanocomposites by Melt Compounding of TEMPO-Treated Wood Fibers in Thermoplastic Starch Matrix

Directory of Open Access Journals (Sweden)

Aline Cobut

2014-04-01

Full Text Available To facilitate melt compounding of cellulose nanofibrils (CNF based composites, wood pulp fibers were subjected to a chemical treatment whereby the fibers were oxidized using 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO. This treatment introduced negatively charged carboxylate groups to the fibers. TEMPO-treated fibers (TempoF were added to a mixture of amylopectin starch, glycerol, and water. Granules were prepared from this mixture and processed into CNF composites by extrusion. TempoF were easier to process into composites as compared with non-treated pulp fibers (PF. SEM revealed partial disintegration of TempoF during melt processing. Consequently, TempoF gave composites with much better mechanical properties than those of conventional composites prepared from pulp fibers and TPS. Particularly, at 20 wt% TempoF content in the composite, the modulus and strength were much improved. Such a continuous melt processing route, as an alternative to laboratory solvent casting techniques, may promote large-scale production of CNF-based composites as an environmentally friendly alternative to synthetic plastics/composites.

Composition, texture and methane potential of cellulosic residues from Lewis acids organosolv pulping of wheat straw.

Science.gov (United States)

Constant, Sandra; Barakat, Abdellatif; Robitzer, Mike; Di Renzo, Francesco; Dumas, Claire; Quignard, Françoise

2016-09-01

Cellulosic pulps have been successfully isolated from wheat straw through a Lewis acids organosolv treatment. The use of Lewis acids with different hardness produced pulps with different delignification degrees. The cellulosic residue was characterised by chemical composition, X-ray diffraction, FT-IR spectroscopy, N2 physisorption, scanning electron microscopy and potential for anaerobic digestibility. Surface area and pore volume increased with the hardness of the Lewis acid, in correspondence with the decrease of the amount of lignin and hemicellulose in the pulp. The non linearity of the correlation between porosity and composition suggests that an agglomeration of cellulose fibrils occurs in the early stages of pulping. All organosolv pulps presented a significantly higher methane potential than the parent straw. A methane evolution of 295Ncm(3)/g OM was reached by a moderate improvement of the accessibility of the native straw. Copyright © 2016 Elsevier Ltd. All rights reserved.

CP/MAS ¹³C NMR study of pulp hornification using nanocrystalline cellulose as a model system.

Science.gov (United States)

Idström, Alexander; Brelid, Harald; Nydén, Magnus; Nordstierna, Lars

2013-01-30

The hornification process of paper pulp was investigated using solid-state (13)C NMR spectroscopy. Nanocrystalline cellulose was used to serve as a model system of the crystalline parts of the fibrils in pulp fibers. Characterization of the nanocrystalline cellulose dimensions was carried out using scanning electron microscopy. The samples were treated by drying and wetting cycles prior to NMR analysis where the hornification phenomenon was recorded by spectral changes of the cellulose C-4 carbon signals. An increase of the crystalline signal and a decrease of the signals corresponding to the accessible amorphous domains were found for both paper pulp and nanocrystalline cellulose. These spectral changes grew stronger with repeating drying and wetting cycles. The results show that cellulose co-crystallization contribute to hornification. Another conclusion is that the surfaces of higher hydrophobicity in cellulose fibrils have an increased preference for aggregation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Wood chemistry symposium: from muka to lignin

Energy Technology Data Exchange (ETDEWEB)

MacLeod, M.

1979-01-01

The Canadian Wood Chemistry Symposium held during September, 1979, is reviewed. The chemical and physical explanations of delignification were debated. Problems of mechanical pulping include insufficient brightness, yellowing, and low strength relative to energy consumption. A session on chemicals, energy, and food from wood began with criteria for a viable project, which included adequate return on investment, modest capital investment requirements, identified pre-existing markets, and favorable thermodynamic balances. The pulp and paper industry should improve its methods of using bark and wood waste in direct combustion (by pre-drying wastes and improving furnace efficiency) rather than supporting oil-from-wood projects, since using a waste for fuel will free fossil fuels for uses in synthetic fibers and thermoplastics. In the area of food, there are modest successes with cellulose fiber additives to bread and snack food and single cell protein (which, though made from wastes, cannot compete with soy protein). However, making monomeric sugars from wood polysaccharides is not an efficient process, and muka, animal feed supplement from foliage, is successful only in Russia. In Canada it cannot compete with agricultural products. Alpha cellulose is a major wood chemical product. Promising uses include cellulose derived thermoplastics and lignosulphonates for secondary oil recovery. Instead of breaking wood polysaccharides and lignin into monomers and then repolymerizing them, it is possible to use the pre-built polymers; such an approach is illustrated by use of lignin in polyurethane foams, adhesives, and coatings.

Temporal changes in wood crystalline cellulose during degradation by brown rot fungi

DEFF Research Database (Denmark)

Howell, Caitlin; Hastrup, Anne Christine Steenkjær; Goodell, Barry

2009-01-01

The degradation of wood by brown rot fungi has been studied intensely for many years in order to facilitate the preservation of in-service wood. In this work we used X-ray diffraction to examine changes in wood cellulose crystallinity caused by the brown rot fungi Gloeophyllum trabeum, Coniophora...... planes in all degraded samples after roughly 20% weight loss, as well as a decrease in the average observed relative peak width at 2¿ = 22.2°. These results may indicate a disruption of the outer most semi-crystalline cellulose chains comprising the wood microfibril. X-ray diffraction analysis of wood...... subjected to biological attack by fungi may provide insight into degradative processes and wood cellulose structure....

Fabrication of microfibrillated cellulose gel from waste pulp sludge via mild maceration combined with mechanical shearing

Science.gov (United States)

Nusheng Chen; Junyong Zhu; Zhaohui Tong

2016-01-01

This article describes a facile route, which combines mild maceration of waste pulp sludge and a mechanical shearing process, to prepare microfibrillated cellulose (MFC) with a high storage modulus. In the maceration, the mixture of glacial acetic acid and hydrogen peroxide was used to extract cellulose from never-dried waste pulp sludge. Then, two different mechanical...

Application of cellulosic nanofibers to replace with imported long- fiber pulps in paper made from bagasse

Directory of Open Access Journals (Sweden)

Reza ghofran

2017-02-01

Full Text Available In this research, different additives of cellulose nanofibers, cationic starch and polyacrylamide to bagasse pulp and their impact on the handsheet strengths were investigated aiming to replace with imported long-fiber softwood pulp in Pars paper factory. For this purpose, first 3% bleached bagasse cellulose nanofibers, 3% unbleached nano-lignocellulosic fibers, 0.5, 0.7 and 1% cationic starch, and 0.03, 0.05 and 0.1% cationic polyacrylamide were added separately to bagasse pulp. In the next stage,3% bleached bagasse cellulose nanofibers and 3% unbleached nano-lignocellulosic fibers along with 0.5% cationic starch or 0.05% cationic polyacrylamide were used. The results showed, adding nano-cellulose fibers along with cationic polyacrylamide or starch have increased handsheet strengths significantly. Yet, the best treatment was the addition of 3% nano-lignocellulose along with 0.5% cationic starch which resulted in the higher tensile and burst strengths and lower tear and fold strengths than that of adding 12.5% long fibers to bagasse pulp. So that, comparing with paper made from pure bagasse pulp it showed the increase of 16.57% in tensile index, 8.47% in burst index, 9.77% in tear index, and 168.85% in folding strength.

Preparation and Characterization of Cellulose Nanofibers from Two Commercial Hardwood and Softwood Pulps

DEFF Research Database (Denmark)

Stelte, Wolfgang; Sanadi, Anand R.

2009-01-01

The aim of this work was to study the mechanical fibrillation process for the preparation of cellulose nanofibers from two commercial hard- and softwood cellulose pulps. The process consisted of initial refining and subsequent high-pressure homogenization. The progress in fibrillation was studied...

Extraction and characterization of cellulose nano whiskers from balsa wood

International Nuclear Information System (INIS)

Morelli, Carolina L.; Bretas, Rosario E.S.; Marconcini, Jose M.; Pereira, Fabiano V.; Branciforti, Marcia C.

2011-01-01

In this study cellulose nano whiskers were obtained from balsa wood. For this purpose, fibers of balsa wood were subjected to hydrolysis reactions for lignin and hemi cellulose digestion and acquisition of nano-scale cellulose. Cellulose nano crystals obtained had medium length and thickness of 176 nm and 7 nm respectively. Infrared spectroscopy and x-ray diffraction showed that the process used for extracting nano whiskers could digest nearly all the lignin and hemi cellulose from the balsa fiber and still preserve the aspect ratio and crystallinity, satisfactory enough for future application in polymer nano composites. Thermogravimetry showed that the onset temperature of thermal degradation of cellulose nano crystals (226 degree C) was higher than the temperature of the balsa fiber (215 degree C), allowing its use in molding processes with many polymers from the molten state.(author)

Can Acceptable Pulp be Obtained from Eucalyptus globulus Wood Chips after Hemicellulose Extraction?

OpenAIRE

Francisco López; M. Trinidad García; Vicente Mena; J. Mauricio Loaiza; Minerva A. M. Zamudio; Juan C. García

2014-01-01

This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or be...

Solution blow spun nanocomposites of poly(lactic acid)/cellulose nanocrystals from Eucalyptus kraft pulp

Science.gov (United States)

Cellulose nanocrystals (CNCs) were extracted from Eucalyptus kraft pulp by sulfuric acid hydrolysis, and esterified with maleic anhydride (CNCMA). The incorporation of sulfate ester groups on the cellulose surface resulted in higher stability of the nanoparticles in aqueous suspensions and lower the...

Laser cleaning of particulates from paper: Comparison between sized ground wood cellulose and pure cellulose

International Nuclear Information System (INIS)

Arif, S.; Kautek, W.

2013-01-01

Visible laser cleaning of charcoal particulates from yellow acid mechanical ground wood cellulose paper was compared with that from bleached sulphite softwood cellulose paper. About one order of magnitude of fluence range is available for a cleaning dynamics between the cleaning threshold and the destruction threshold for two laser pulses. Wood cellulose paper exhibited a higher destruction threshold of the original paper than that of the contaminated specimen because of heat transfer from the hot or evaporating charcoal particulates. In contrast, the contaminated bleached cellulose paper exhibited a higher destruction threshold due to shading by the particulates. The graphite particles are not only detached thermo-mechanically, but also by evaporation or combustion. A cleaning effect was found also outside the illuminated areas due to lateral blasting. Infrared measurements revealed dehydration/dehydrogenation reactions and cross-links by ether bonds together with structural changes of the cellulose chain arrangement and the degree of crystallinity.

Measurement of cellulose content, Kraft pulp yield and basic density ...

African Journals Online (AJOL)

Previous descriptions of multisite and multispecies near infra-red (NIR) spectroscopic calibrations for predicting cellulose content (CC) and Kraft pulp yield (KPY) in eucalypt woodmeal demonstrated that large, single calibrations provide precise predictions for a wide range of sites and species. These have since been used ...

Production of Cellulosic Polymers from Agricultural Wastes

Directory of Open Access Journals (Sweden)

A. U. Israel

2008-01-01

Full Text Available Cellulosic polymers namely cellulose, di-and triacetate were produced from fourteen agricultural wastes; Branch and fiber after oil extraction from oil palm (Elais guineensis, raffia, piassava, bamboo pulp, bamboo bark from raphia palm (Raphia hookeri, stem and cob of maize plant (Zea mays, fruit fiber from coconut fruit (Cocos nucifera, sawdusts from cotton tree (Cossypium hirsutum, pear wood (Manilkara obovata, stem of Southern gamba green (Andropogon tectorus, sugarcane baggase (Saccharium officinarum and plantain stem (Musa paradisiaca. They were subjected to soda pulping and hypochlorite bleaching system. Results obtained show that pulp yield from these materials were: 70.00, 39.59, 55.40, 86.00, 84.60, 80.00, 40.84, 81.67, 35.70, 69.11, 4.54, 47.19, 31.70 and 52.44% respectively. The pulps were acetylated with acetic anhydride in ethanoic acid catalyzed by conc. H2SO4 to obtain cellulose derivatives (Cellulose diacetate and triacetate. The cellulose diacetate yields were 41.20, 17.85, 23.13, 20.80, 20.23, 20.00, 39.00, 44.00, 18.80, 20.75, 20.03, 41.20, 44.00, and 39.00% respectively while the results obtained as average of four determinations for cellulose triacetate yields were: 52.00, 51.00, 43.10, 46.60, 49.00, 35.00, 40.60, 54.00, 57.50, 62.52, 35.70. 52.00, 53.00 and 38.70% respectively for all the agricultural wastes utilized. The presence of these cellulose derivatives was confirmed by a solubility test in acetone and chloroform.

A utilização de perácidos na deslignificação e no branqueamento de polpas celulósicas The use of peracids in delignification and cellulose pulp bleaching

Directory of Open Access Journals (Sweden)

Lilian Borges Brasileiro

2001-12-01

Full Text Available Peracids are strong oxidant species and their use is being largely studied in the delignification and cellulose pulp bleaching. Some of them has already an industrial application, specially in non-conventional bleaching sequences like ECF (Elemental chlorine free and TCF (Totally chlorine free. This review presents the main aspects of the structure, properties, preparation and reaction of peracids (peracetic acid, peroxymonosulfuric acid and their mixture with lignin, specially for peracetic acid. Information about bleaching and delignification of wood pulps with peracids and the factors affecting its efficiency are also presented.

Endurance of high molecular weight carboxymethyl cellulose in corrosive environments

Science.gov (United States)

Murodov, M. M.; Rahmanberdiev, G. R.; Khalikov, M. M.; Egamberdiev, E. A.; Negmatova, K. C.; Saidov, M. M.; Mahmudova, N.

2012-07-01

Lignin obtained from the waste cooking liquor, formed after soda pulping process, is used as an inhibitor of NaCMC thermo oxidative degradation in presence of in extreme conditions during drilling oil wells. In this paper the schematic process of obtaining NaCMC by the principle of "monoapparat" on the basis of cellulose produced by non-wood cellulose materials is presented.

Grafted wood pulp containing quaternary ammonium group and its application in the removal of different anions from aqueous solution

International Nuclear Information System (INIS)

Sokker, H.H.

2005-01-01

Network wood pulp based on acrylonitrile has been chemically modified through different reactions to obtain group capable of anion exchange. Graft copolymerization of acrylonitrile onto wood pulp was carried out by using gamma-radiation 60 Co. Factors affecting the grafting process e.g radiation dose and monomer concentration were investigated.The chemical modification of cyano groups were carried out by reaction with ethanol amine producing oxazoline group followed by quaternization of tertiary amine by reaction with benzyl chloride producing quaternary ammonium salt. The grafted and modified wood pulp were characterized by FTIR, SEM and TGA.Qualitative experiments of adsorption were conducted to evaluate the modified wood pulp on fixing sulfate, phosphate,nitrate and dichromate from aqueous solution using batch extractions. Based on the results obtained, it may be concluded that it is possible to modify chemically wood pulp containing cyano groups by different routes for its usage as anion exchanger

Chromatography Of Metal Ions On Wood Cellulose Impregnated ...

African Journals Online (AJOL)

Adsorption chromatography of some heavy metal ions on wood cellulose of saw dust (wood waste dust) modified with hydrochloric acid, urea and thiourea was studied. Atomic absorption spectrophotometry (AAS) was used to determine the initial concentration of solutions of Zn2+, Cu2+, Ni2+, Pb2+, and Fe3+ metal ions.

Spatially Resolved Characterization of Cellulose Nanocrystal-Polypropylene Composite by Confocal Raman Microscopy

Science.gov (United States)

Umesh P. Agarwal; Ronald Sabo; Richard S. Reiner; Craig M. Clemons; Alan W. Rudie

2012-01-01

Raman spectroscopy was used to analyze cellulose nanocrystal (CNC)–polypropylene (PP) composites and to investigate the spatial distribution of CNCs in extruded composite filaments. Three composites were made from two forms of nanocellulose (CNCs from wood pulp and the nanoscale fraction of microcrystalline cellulose) and two of the three composites investigated used...

Microfibrillated cellulose from bamboo pulp and its properties

International Nuclear Information System (INIS)

Zhang, Junhua; Song, Hainong; Lin, Lu; Zhuang, Junping; Pang, Chunsheng; Liu, Shijie

2012-01-01

Microfibrillated cellulose (MFC) was obtained by disintegrating bleached kraft bamboo (Phyllostachys pubescens) pulp with a procedure of chemical pretreatment and high-pressure homogenization. The influences of sodium hydroxide dosage and homogenization times were evaluated by water retention value (WRV) of MFC. The properties, such as the surface morphology, rheological property and carboxyl acid content of MFC were also characterized using scanning electron microscope (SEM), rheometer and headspace gas chromatography (HS-GC) separately.

Rice straw pulp obtained by using various methods.

Science.gov (United States)

Rodríguez, Alejandro; Moral, Ana; Serrano, Luis; Labidi, Jalel; Jiménez, Luis

2008-05-01

Rice straw was used as an alternative raw material to obtain cellulosics pulps. Pulping was done by using classics reagents as soda (with anthraquinone and parabenzoquinone as aditives), potassium hydroxide and Kraft process. The holocellulose, alpha-cellulose and lignin contents of rice straw (viz. 60.7, 41.2 and 21.9 wt%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using soda, soda and anthraquinone at 1 wt%, soda and parabenzoquinone at 1 wt%, potassium hydroxide and sodium sulphate (Kraft process) under two different sets of operating conditions, namely: (a) a 10 wt% reagent concentration, 170 degrees C and 60 min; and (b) 15 wt% reagent, 180 degrees C and 90 min. The solid/liquid ratio was 6 in both cases. Paper sheets made from pulp extracted by cooking with soda (15 wt%) and AQ (1 wt%) at 180 degrees C and 90 min pulp exhibit the best drainage index, breaking length, stretch and burst index (viz. 23 degrees SR, 3494 m, 3.34% and 2.51 kN/g, respectively).

Cellulose fibril aggregation studies of eucalyptus dissolving pulps using atomic force microscopy

CSIR Research Space (South Africa)

Chunilall, Viren

2006-11-01

Full Text Available STUDIES OF Eucalyptus DISSOLVING PULPS USING ATOMIC FORCE MICROSCOPY V. Chunilall1, J.Wesley-Smith2, T. Bush1 1CSIR, Forestry and Forest Product Research Centre, P.O. Box 17001, Congella, 4013, South Africa. 2Electron Microscope Unit, University of Kwa... pulp using atomic force microscopy (AFM) have reported increased cellulose fibril aggregation during processing, and a concomitant decrease in surface area available for chemical reaction1,2. These findings were subsequently confirmed...

Optically Transparent Wood from a Nanoporous Cellulosic Template: Combining Functional and Structural Performance.

Science.gov (United States)

Li, Yuanyuan; Fu, Qiliang; Yu, Shun; Yan, Min; Berglund, Lars

2016-04-11

Optically transparent wood (TW) with transmittance as high as 85% and haze of 71% was obtained using a delignified nanoporous wood template. The template was prepared by removing the light-absorbing lignin component, creating nanoporosity in the wood cell wall. Transparent wood was prepared by successful impregnation of lumen and the nanoscale cellulose fiber network in the cell wall with refractive-index-matched prepolymerized methyl methacrylate (MMA). During the process, the hierarchical wood structure was preserved. Optical properties of TW are tunable by changing the cellulose volume fraction. The synergy between wood and PMMA was observed for mechanical properties. Lightweight and strong transparent wood is a potential candidate for lightweight low-cost, light-transmitting buildings and transparent solar cell windows.

FTIR spectroscopy and X-ray powder diffraction characterization of microcrystalline cellulose obtained from alfa fibers

Directory of Open Access Journals (Sweden)

Trache D.

2013-07-01

Full Text Available Many cereal straws have been used as raw materials for the preparation of microcrystalline cellulose (MCC. These raw materials were gradually replaced with wood products; nevertheless about 10% of the world overall pulp production is obtained from non-wood raw material. The main interest in pulp made from straw is that it provides excellent fibres for different industries with special properties, and that it is the major available source of fibrous raw material in some geographical areas. The aim of the present work was to characterize microcrystalline cellulose prepared from alfa fibers using the hydrolysis process. The products obtained are characterized with FTIR spectroscopy and X-ray powder diffraction. As a result, FTIR spectroscopy is an appropriate technique for studying changes occurred by any chemical treatment. The spectrum of alfa grass stems shows the presence of lignin and hemicelluloses. However, the cellulose spectrum indicates that the extraction of lignin and hemicellulose was effective. The X-ray analysis indicates that the microcrystalline cellulose is more crystalline than the source material.

Effect of Mixing Temperature of CMP Pulp and Cellulose Nanofiber on Paper Properties

Directory of Open Access Journals (Sweden)

Sahba Alinia

2013-06-01

Full Text Available Several processing parameters affect the function of cellulose nanofiber as an environmentally friend cellulosic reinforcer. One of the potential parameters can be the mixing temperature of pulp and cellulose nanofiber that has been investigated in this study. In order to study the influence of this parameter, mixing drainage velocity and the air permeability and strength properties of resulting paper were measured. A mixture of chemi-mechanical pulp suspensions (with concentration of 0.2 wt% and freeness of 250 ml, CSF containing 5 wt% cellulose nanofiber were prepared. This mixture was then stirred at 25, 50, and 70 ◦C using a magnetic stirrer for 1 hour followed by draining using vacuum filtration to make wet handsheet. The wet handsheet was first pressed, and then dried in oven at 100 ◦C for 24 hours. The test’ results showed that the increase of mixing temperature led to decreasing drainage time and air permeability. The strength properties of paper reinforced by nanofibers were positively affected by mixing temperature (i.e. the more mixing temperature, the higher strength. The data of tensile strength index was considerably increased. The tear strength of paper increased approximately by 200% over rising mixing temperature.

High-alkali low-temperature polysulfide pulping (HALT) of Scots pine.

Science.gov (United States)

Paananen, Markus; Sixta, Herbert

2015-10-01

High-alkali low-temperature polysulfide pulping (HALT) was effectively utilised to prevent major polysaccharide losses while maintaining the delignification rate. A yield increase of 6.7 wt% on wood was observed for a HALT pulp compared to a conventionally produced kappa number 60 pulp with comparable viscosity. Approximately 70% of the yield increase was attributed to improved galactoglucomannan preservation and 30% to cellulose. A two-stage oxygen delignification sequence with inter-stage peroxymonosulphuric acid treatment was used to ensure delignification to a bleachable grade. In a comparison to conventional pulp, HALT pulp effectively maintained its yield advantage. Diafiltration trials indicate that purified black liquor can be directly recycled, as large lignin fractions and basically all dissolved polysaccharides were separated from the alkali-rich BL. Copyright © 2015 Elsevier Ltd. All rights reserved.

Cellulose, hemicelluloses, lignin and ash content of some organic materials and their suitability for use as paper pulp supplements.

Science.gov (United States)

Ververis, C; Georghiou, K; Danielidis, D; Hatzinikolaou, D G; Santas, P; Santas, R; Corleti, V

2007-01-01

Freshwater algal biomass and orange and lemon peels were assessed as tissue paper pulp supplements. Cellulose and hemicellulose contents of algal biomass were 7.1% and 16.3%, respectively, whereas for citrus peels cellulose content ranged from 12.7% to 13.6% and hemicellulose from 5.3% to 6.1%. For all materials, lignin and ash content was 2% or lower, rendering them suitable for use as paper pulp supplements. The addition of algal biomass to paper pulp increased its mechanical strength significantly. However, brightness was adversely affected by chlorophyll. The addition of citrus peels in paper pulp had no effect on breaking length, increased bursting strength and decreased tearing resistance. Brightness was negatively affected at proportions of 10%, because citrus peel particles behave as coloured pigments. The cost of both materials is about 45% lower than that of conventional pulp, resulting in a 0.9-4.5% reduction in final paper price upon their addition to the pulp.

Avaliação da madeira e da polpação kraft em clones de eucaliptos Wood evaluation and Kraft pulping in eucalypts clones

Directory of Open Access Journals (Sweden)

Adriana de Fátima Gomes Gouvêa

2009-12-01

Full Text Available A produção de celulose de baixo custo e alta qualidade requer madeira adequada e bem selecionada. A seleção de clones superiores tem sido realizada com base em critérios como densidade básica, rendimento gravimétrico da polpação e composição química da madeira, especialmente de celulose, hemiceluloses, extrativos e ligninas. O objetivo deste trabalho foi avaliar as características da madeira de Eucalyptus, por método destrutivo, e a produção de polpa celulósica kraft em seis clones. Utilizaram-se cinco árvores de cada clone, aos 3 anos de idade, plantadas em espaçamento 3,0 m x 3,3 m, nas regiões de Cocais, Guanhães, Rio Doce e Santa Bárbara, Estado de Minas Gerais. A densidade básica foi medida em discos extraídos a 1,3 m de altura do solo (DAP e em cavacos da árvore inteira (amostra composta. A composição química foi medida em amostras de serragem, retiradas no DAP. Os cozimentos foram efetuados a partir de cavacos da árvore inteira. Verificou-se que a densidade medida no DAP foi ligeiramente superior à medida nos cavacos da árvore toda. A composição química geral da madeira foi muito influenciada pelo tipo de clone, local de plantio e interação. Locais mais montanhosos produziram madeira com maior teor de celulose e menor de hemicelulose. A madeira do clone F da região de Santa Bárbara e Cocais apresentaram madeiras de qualidade inferior para produção de polpa celulósica. Os melhores rendimentos de polpação kraft foram alcançados com o clone B nas regiões de Guanhães e Santa Bárbara.Low cost and high quality cellulose production demands appropriate wood. The selection of superior clones has been done based on some criteria as basic density, gravimetric yield of pulping and wood chemical composition, especially of cellulose, hemicelluloses, extractive and lignin contents. This study aimed at evaluating the characteristics of the Eucalyptus wood, by destructive methods, and the Kraft pulping

The Effect of Wood Alignment on Wood Grinding – Part 1: Properties of Pulp and Fines Revealed in the Grinding Mechanism

Directory of Open Access Journals (Sweden)

Erkki Tapani Saharinen

2016-03-01

Full Text Available In industrial wood grinding, logs are pressed against a rotating stone, with the logs and fiber axis parallel to the axis of the stone. The objective of this study is to clarify how the wood alignment affects the process and pulp properties. In this research, wood blocks were fed into a laboratory grinder with various alignments in relation to the surface of the grinding stone. The effects of the alignment on the properties of the pulp and the amount and quality of fines were measured. A grinding mechanism was proposed. The results show that the pulp quality is very sensitive to the angle between the stone surface and the log. In gentle refining, the fiber structure is loosened by fatigue before it is bent on the surface; pressure pulses produce fibrillar material, and fibers develop toward having good bonding ability. In forced grinding, the process is “violent”, and the fiber wears and becomes crushed immediately on the surface into small particles with low bonding ability.

Wood-plastic composites using thermomechanical pulp made from oxalic acid-pretreated red pine chips

Science.gov (United States)

J.E. Winandy; N.M. Stark; E. Horn

2008-01-01

The characteristics and properties of wood fiber is one of many factors of critical importance to the performance of wood-plastic composites. In commercial thermo-mechanical pulping (TMP) of wood chips to produce fibers, high temperatures (>100°C) are used to separate the fibers during TMP refining. These mechanical pressures and temperatures are usually modulated...

Probing crystallinity of never-dried wood cellulose with Raman spectroscopy

Science.gov (United States)

Umesh P. Agarwal; Sally A. Ralph; Richard S. Reiner; Carlos Baez

2016-01-01

The structure of wood cell wall cellulose in its native state remains poorly understood, limiting the progress of research and development in numerous areas, including plant science, biofuels, and nanocellulose based materials. It is generally believed that cellulose in cell wall microfibrils has both crystalline and amorphous regions. However, there is evidence that...

Comparison of Cellulose Supramolecular Structures Between Nanocrystals of Different Origins

Science.gov (United States)

Umesh P. Agarwal; Richard S. Reiner; Christopher G. Hunt; Jeffery Catchmark; E. Johan Foster; Akira Isogai

2015-01-01

In this study, morphologies and supramolecular structures of CNCs from wood-pulp, cotton, bacteria, tunicate, and cladophora were investigated. TEM was used to study the morphological aspects of the nanocrystals whereas Raman spectroscopy provided information on the cellulose molecular structure and its organization within a CNC. Dimensional differences between the...

Evaluation of a value prior to pulping-thermomechanical pulp business concept. Part 2.

Science.gov (United States)

Ted Bilek; Carl Houtman; Peter Ince

2011-01-01

Value Prior to Pulping (VPP) is a novel biorefining concept for pulp mills that includes hydrolysis extraction of hemicellulose wood sugars and acetic acid from pulpwood prior to pulping. The concept involves conversion of wood sugars via fermentation to fuel ethanol or other chemicals and the use of remaining solid wood material in the pulping process. This paper...

Reinforcing Natural Rubber with Cellulose Nanofibrils Extracted from Bleached Eucalyptus Kraft Pulp

Science.gov (United States)

Chunmei Zhang; Tianliang Zhai; Ronald Sabo; Craig Clemons; Yi Dan; Lih-Sheng Turng

2014-01-01

Reinforced natural rubber (NR) nanocomposites were prepared by solution mixing, casting, and evaporation of pre-vulcanized natural rubber latex and an aqueous suspension of cellulose nanofibrils (CNFs) extracted from bleached eucalyptus kraft pulp. Scanning electron microscopy (SEM) images showed that there were no micro-scaled aggregates observed in the nanocomposites...

A primary estimation of PCDD/Fs release reduction from non-wood pulp and paper industry in China based on the investigation of pulp bleaching with chlorine converting to chlorine dioxide.

Science.gov (United States)

Xiao, Qingcong; Song, Xiaoqian; Li, Wenchao; Zhang, Yuanna; Wang, Hongchen

2017-10-01

Chlorine bleaching technology (C process, CEH process, H process and theirs combination), which was identified as a primary formation source of PCDD/Fs, is still widely used by the vast majority of Chinese non-wood pulp and paper mills (non-wood PMs). The purpose of this study was to provide information and data support for further eliminating dioxin for non-wood PMs in China, and especially to evaluate the PCDD/Fs release reduction for those mills converting their pulp bleaching processes from CEH to ECF. The PCDD/Fs concentrations of the bleached pulp and bleaching wastewater with ECF bleaching were in the ranges of 0.13-0.8 ng TEQ kg -1 , and 0.15-1.9 pg TEQ L -1 , respectively, which were far lower than those with CEH process, indicating that the ECF process is an effective alternative bleaching technology to replace CEH in Chinese non-wood PMs to reduce dioxin release. The release factor via flue gas of the alkali recovery boiler in Chinese non-wood PMs was first reported to be 0.092 μg TEQ Ad t -1 in this study. On the assumption that pulp bleaching processes of all Chinese non-wood PMs were converted from CEH to ECF, the annual release of PCDD/Fs via the bleaching wastewater and bleached pulp would be reduced by 79.1%, with a total of 1.60 g TEQ. Copyright © 2017 Elsevier Ltd. All rights reserved.

Assessment of wood-inhabiting Basidiomycetes for biokraft pulping of softwood chips

CSIR Research Space (South Africa)

Wolfaardt, F

2004-10-01

Full Text Available Wood-inhabiting Basidiomycetes have been screened for various applications in the pulp and paper industry and it is evident that different fungi need to be used to suit the specific requirements of each application. This study assessed...

A co-production of sugars, lignosulfonates, cellulose, and cellulose nanocrystals from ball-milled woods.

Science.gov (United States)

Du, Lanxing; Wang, Jinwu; Zhang, Yang; Qi, Chusheng; Wolcott, Michael P; Yu, Zhiming

2017-08-01

This study demonstrated the technical potential for the large-scale co-production of sugars, lignosulfonates, cellulose, and cellulose nanocrystals. Ball-milled woods with two particle sizes were prepared by ball milling for 80min or 120min (BMW 80 , BMW 120 ) and then enzymatically hydrolyzed. 78.3% cellulose conversion of BMW 120 was achieved, which was three times as high as the conversion of BMW 80 . The hydrolyzed residues (HRs) were neutrally sulfonated cooking. 57.72g/L and 88.16g/L lignosulfonate concentration, respectively, were harvested from HR 80 and HR 120 , and 42.6±0.5% lignin were removed. The subsequent solid residuals were purified to produce cellulose and then this material was acid-hydrolyzed to produce cellulose nanocrystals. The BMW 120 maintained smaller particle size and aspect ratio during each step of during the multiple processes, while the average aspect ratio of its cellulose nanocrystals was larger. The crystallinity of both materials increased with each step of wet processing, reaching to 74% for the cellulose. Copyright © 2017 Elsevier Ltd. All rights reserved.

Yield-increasing additives in kraft pulping: Effect on carbohydrate retention, composition and handsheet properties

Energy Technology Data Exchange (ETDEWEB)

Vaaler, David Andre Grimsoeen

2008-07-01

In this thesis, increased hemicellulose retention during kraft pulping has been studied. The work has been divided into three parts: i) Development of an accessible and reliable method for determination of carbohydrate composition of kraft pulps ii) Investigation of the composition and molecular mass distributions of the carbohydrates in kraft pulps with increased hemicellulose content iii) Investigation of the effect of increased hemicellulose content on the sheet properties of kraft pulps with increased hemicellulose content. A method for carbohydrate determination was developed. In this method, enzymes are used to hydrolyse the pulp into monosaccharides. A relatively mild acid hydrolysis is performed prior to detection on an HPLC with an RI-detector. The pulp is not derivatized and no pre-treatment (mechanical or chemical) is needed to determine the carbohydrate composition using the method developed here. Peak deconvolution software is used to improve the accuracy. Polysulphide and H2S primarily increase the glucomannan yield, which can be boosted by up to 7 % on o.d. wood. However, the cellulose yield is more affected by the cooking time and the maximum yield increase of cellulose is approximately 2 % on o.d. wood compared to an ordinary kraft pulp. The cooking time is influenced by sulphide ion concentration, AQ addition and the final Kappa number. The xylan yield is remarkably stable, however the alkali profile during the cook may influence the xylan yield. Surface xylan content of the fibres depends on residual alkali concentration in the black liquor. The molecular mass distributions of cellulose and hemicellulose were determined for pulps with increased hemicellulose content using size exclusion chromatography. Deconvolution by peak separation software is used to gain information about the degree of polymerization for cellulose and hemicellulose. The average DP of glucomannan in the kraft fibre was found to be 350 +- 30 and the average DP of xylan in the

Stone-ground wood pulp-reinforced polypropylene composites: Water uptake and thermal properties

Directory of Open Access Journals (Sweden)

Joan Pere López

2012-11-01

Full Text Available Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC and thermogravimetric analysis (TGA were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC.

Morphological and Chemical Characterization of Green Bamboo (Dendrocalamopsis oldhami (Munro Keng f. for Dissolving Pulp Production

Directory of Open Access Journals (Sweden)

Shilin Cao

2014-06-01

Full Text Available With the sustained growth of dissolving pulp demand all over the world, the search for alternative bamboo materials has come into focus in China due to the shortage of wood and the abundance of bamboo resources. In this study, to obtain updated information concerning green bamboo growing in southeastern China and to develop its processing technologies for dissolving pulp, the fiber morphology, chemical composition, elemental composition, degree of polymerization (DP of cellulose, and crystallinity index (CrI of cellulose were investigated. The experimental results show that green bamboo has potential for use as dissolving pulp because it has a lower Runkel ratio and fines content than moso bamboo, and a much lower lignin content and similar α-cellulose and hemicellulose contents compared to softwoods and hardwoods. Compared to the cortex and culm, the node had the shortest fibers and more than 30% of fines, the highest content of extractives and lignin, and the lowest α-cellulose content. As a result, a de-knotting operation prior to cooking can contribute to the production of high-grade dissolving pulp. The DP and CrI of cellulose from the node were much lower than that of cellulose from the culm and cortex. Moreover, green bamboo had the high content of ash, primarily distributed in the cortex. The concentration of Si was 4487 ppm in the cortex, nearly five times higher than that in the culm and node.

Radiation carbonization of cellulose, wood and lignin in the presence of air

International Nuclear Information System (INIS)

Rudnev, A.V.; Loginova, L.A.; Val'ter, A.I.

1986-01-01

The process of radiaton carbonization of wood and its separate components (cellulose and lignin) under the effect of γ-radiation is studied. In the process of cellulose and wood meal irradiation a decrease in hydrogen content with the growth of irradiation dose is observed. Simultaneously with hydrogen loss the dose of ∼ 100 kGy an increase in carbon content and a decrease in oxygen content are observed. In wood meal carbon content decreases, oxygen content increases. In lignin the observed changes in the element composition do not exceed experimental error. The results obtained are considered from the viewpoint of dehydration of radicals, formed in the process of irradiation, as well as their oxidation by the air oxygen

Current characterization methods for cellulose nanomaterials.

Science.gov (United States)

Foster, E Johan; Moon, Robert J; Agarwal, Umesh P; Bortner, Michael J; Bras, Julien; Camarero-Espinosa, Sandra; Chan, Kathleen J; Clift, Martin J D; Cranston, Emily D; Eichhorn, Stephen J; Fox, Douglas M; Hamad, Wadood Y; Heux, Laurent; Jean, Bruno; Korey, Matthew; Nieh, World; Ong, Kimberly J; Reid, Michael S; Renneckar, Scott; Roberts, Rose; Shatkin, Jo Anne; Simonsen, John; Stinson-Bagby, Kelly; Wanasekara, Nandula; Youngblood, Jeff

2018-04-23

A new family of materials comprised of cellulose, cellulose nanomaterials (CNMs), having properties and functionalities distinct from molecular cellulose and wood pulp, is being developed for applications that were once thought impossible for cellulosic materials. Commercialization, paralleled by research in this field, is fueled by the unique combination of characteristics, such as high on-axis stiffness, sustainability, scalability, and mechanical reinforcement of a wide variety of materials, leading to their utility across a broad spectrum of high-performance material applications. However, with this exponential growth in interest/activity, the development of measurement protocols necessary for consistent, reliable and accurate materials characterization has been outpaced. These protocols, developed in the broader research community, are critical for the advancement in understanding, process optimization, and utilization of CNMs in materials development. This review establishes detailed best practices, methods and techniques for characterizing CNM particle morphology, surface chemistry, surface charge, purity, crystallinity, rheological properties, mechanical properties, and toxicity for two distinct forms of CNMs: cellulose nanocrystals and cellulose nanofibrils.

Flexible biorefinery for producing fermentation sugars, lignin and pulp from corn stover.

Science.gov (United States)

Kadam, Kiran L; Chin, Chim Y; Brown, Lawrence W

2008-05-01

A new biorefining process is presented that embodies green processing and sustainable development. In the spirit of a true biorefinery, the objective is to convert agricultural residues and other biomass feedstocks into value-added products such as fuel ethanol, dissolving pulp, and lignin for resin production. The continuous biomass fractionation process yields a liquid stream rich in hemicellulosic sugars, a lignin-rich liquid stream, and a solid cellulose stream. This paper generally discusses potential applications of the three streams and specifically provides results on the evaluation of the cellulose stream from corn stover as a source of fermentation sugars and specialty pulp. Enzymatic hydrolysis of this relatively pure cellulose stream requires significantly lower enzyme loadings because of minimal enzyme deactivation from nonspecific binding to lignin. A correlation was shown to exist between lignin removal efficiency and enzymatic digestibility. The cellulose produced was also demonstrated to be a suitable replacement for hardwood pulp, especially in the top ply of a linerboard. Also, the relatively pure nature of the cellulose renders it suitable as raw material for making dissolving pulp. This pulping approach has significantly smaller environmental footprint compared to the industry-standard kraft process because no sulfur- or chlorine-containing compounds are used. Although this option needs some minimal post-processing, it produces a higher value commodity than ethanol and, unlike ethanol, does not need extensive processing such as hydrolysis or fermentation. Potential use of low-molecular weight lignin as a raw material for wood adhesive production is discussed as well as its use as cement and feed binder. As a baseline application the hemicellulosic sugars captured in the hydrolyzate liquor can be used to produce ethanol, but potential utilization of xylose for xylitol fermentation is also feasible. Markets and values of these applications are

The effect of pulping concentration treatment on the properties of microcrystalline cellulose powder obtained from waste paper.

Science.gov (United States)

Okwonna, Okumneme O

2013-10-15

Microcrystalline cellulose (MCC) powder was isolated from three grades of waste paper: book, Groundwood/Newsprint and paperboard, through the processes of pulping and hydrolysis. Pulping treatment on these grades of waste paper was done using varying concentrations of caustic soda. Effects of the concentration of the pulping medium on the thermal and kinetic properties were investigated. Also determined were the effects of this on the physico-chemical properties. The chemical structure was characterized using an infrared spectroscopy (FTIR). Results showed these properties to be affected by the concentration of the pulping medium. Copyright © 2013 Elsevier Ltd. All rights reserved.

Morphological development of cellulose fibrils of a bleached eucalyptus pulp by mechanical fibrillation

Science.gov (United States)

Q.Q. Wang; J.Y. Zhu; R. Gleisner; T.A. Kuster; U. Baxa; S.E. McNeil

2012-01-01

This study reports the production of cellulose nanofibrils (CNF) from a bleached eucalyptus pulp using a commercial stone grinder. Scanning electronic microscopy and transmission electronic microscopy imaging were used to reveal morphological development of CNF at micro and nano scales, respectively. Two major structures were identified (1) highly kinked, naturally...

Supra-molecular structure and chemical reactivity of cellulose I studied using CP/MAS (sup)13 C-NMR

CSIR Research Space (South Africa)

Chunilall, Viren

2013-08-01

Full Text Available There are a few traditional methods of analysing the chemical properties of cellulose I. Some of these methods include the Permanganate number determination, which is used to obtain the lignin content of the pulp [12]. The acid insoluble lignin content... – Fundamental Aspects 88 [10] Fengel D, Wegener G. Wood Chemistry, Ultrastructure, Reactions, Walter de Gruyter; 1984. [11] Uhlmann T. Ullmann's encyclopedia of industrial chemistry. Paper and Pulp. 1991; 18 (A). [12] Permanganate number of pulp, Tappi T...

Control of Atmospheric Emissions in the Wood Pulping Industry, Volume 3.

Science.gov (United States)

Hendrickson, E. R.; And Others

Volume 3 contains chapters 9 through 13 of the final report on the control of atmospheric emissions in the wood pulping industry. These chapters deal with the following topics: sampling and analytical techniques; on-going research related to reduction of emissions; research and development recommendations; current industry investment and operating…

Pulp mill as an energy producer

International Nuclear Information System (INIS)

Kaulamo, O.

1998-01-01

The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

The effects of wood storage on the chemical composition and indigenous microflora of eucalyptus species used in the pulping industry

CSIR Research Space (South Africa)

Ramnath, L

2018-02-01

Full Text Available Lipophilic extractives naturally occurring in wood tend to coalesce during pulping to form pitch deposits, which have particularly undesirable effects on the pulping process and quality of pulp produced. A chemical characterization of different...

Investigation of pulping and paper making potential of weeds

Directory of Open Access Journals (Sweden)

omid Ghaffarzadeh Mollabashi

2017-08-01

Full Text Available Increasing use of wood products accompanying with resource constraint has revealed the importance of nonwood based material. In this study, pulping and papermaking potential of three varieties of weeds including Xanthium spinosum, Carthamus tinctorius and Cyperus papyrus have been considered. At first, chemical components of the samples i.e. cellulose, lignin and extractives have been measured following TAPPI standard test methods. Afterwards, pulping process based as soda and Kraft has been carried out and the pulp properties i.e. screen yield and reject, kappa number, caliper, bust index, tear index, brightness have been considered. According to the results, the amount cellulose, lignin and extractives have been measured for the Xanthium spinosum %38.15, %13.5 and 4.72, respectively. Theses parameters have been estimated about %38.25, %10.3 and % 2.95 for Carthamus tinctorius and %38.8, %19.2 and 4.4 in case of papyrus. The yield of soda and Kraft pulp of the papyrus was more than Xanthium spinosum and Carthamus tinctorius. Among all treatments, the highest screen yield related to soda pulping of Cyperus papyrus by %39.8 which has been obtained by 175 centigrade as a maximum temperature, L/W: 6/1, active alkaline: %30 and 90 minutes as the time at temperature. The lowest and highest amounts of the tear index were related to soda pulp sample of the Carthamus tinctorius and Kraft pulp sample of Xanthium spinosum by 2.49 and 8.1, respectively. In addition, the lowest and highest amounts of the bursting index were related to soda pulp sample of the Cyperus papyrus and Kraft pulp sample of Xanthium spinosum by 0.61and 2.48, respectively. Meanwhile, soda pulp sample of the Cyperus papyrus showed the highest amount of brightness with %45 ISO.

Revealing organization of cellulose in wood cell walls by Raman imaging

Science.gov (United States)

Umesh P. Agarwal; Sally A. Ralph

2007-01-01

Anisotropy of cellulose organization in mature black spruce wood cell wall was investigated by Raman imaging using a 1 [mu]m lateral-resolution capable confocal Raman microscope. In these studies, wood cross sections (CS) and radial longitudinal sections (LS) that were partially delignified by acid chlorite treatment were used. In the case of CS where latewood cells...

China’s High-yield Pulp Sector and Its Carbon Dioxide Emission: Considering the Saved Standing Wood as an Increase of Carbon Storage

Directory of Open Access Journals (Sweden)

Yanhong Gao

2014-11-01

Full Text Available The production of high-yield pulp in China has increased significantly in recent years. The well-known advantages of this type of pulp include low production cost, high opacity, and good paper formation. In the context of state-of-the-art technologies, China’s high-yield pulping, which is dominated by the PRC-APMP (preconditioning refiner chemical treatment-alkaline peroxide mechanical pulping process, has a much higher energy input but a significantly lower wood consumption in comparison with the kraft pulping process. If the saved wood in the forest or plantation is considered as an increment of carbon storage, then the carbon dioxide emission from the production of high-yield pulp can be regarded as much lower than that of kraft pulp.

Evolution of Lignocellulosic Macrocomponents in the Wastewater Streams of a Sulfite Pulp Mill: A Preliminary Biorefining Approach

Directory of Open Access Journals (Sweden)

Tamara Llano

2015-01-01

Full Text Available The evolution of lignin, five- and six-carbon sugars, and other decomposition products derived from hemicelluloses and cellulose was monitored in a sulfite pulp mill. The wastewater streams were characterized and the mass balances throughout digestion and total chlorine free bleaching stages were determined. Summative analysis in conjunction with pulp parameters highlights some process guidelines and valorization alternatives towards the transformation of the traditional factory into a lignocellulosic biorefinery. The results showed a good separation of cellulose (99.64% during wood digestion, with 87.23% of hemicellulose and 98.47% lignin dissolved into the waste streams. The following steps should be carried out to increase the sugar content into the waste streams: (i optimization of the digestion conditions increasing hemicellulose depolymerization; (ii improvement of the ozonation and peroxide bleaching stages, avoiding deconstruction of the cellulose chains but maintaining impurity removal; (iii fractionation of the waste water streams, separating sugars from the rest of toxic inhibitors for 2nd generation biofuel production. A total of 0.173 L of second-generation ethanol can be obtained in the spent liquor per gram of dry wood. The proposed methodology can be usefully incorporated into other related industrial sectors.

Use of perborate in the bleaching of ethanolamine pulp from olive wood

Energy Technology Data Exchange (ETDEWEB)

Ramos, E.; Torre, M.J. de la; Gutiérrez, J.C.

2016-11-01

In this work, we studied the influence of the bleacher concentration(2.5-5.5%), temperature (60-80 ºC) and time (60-180 min) on the reagent (perborate) consumption by dry pulp, various properties of the bleached pulp (yield, kappa number, brightness and viscosity/kappa numberratio), and some physical properties of paper sheets obtainedfrom it (tear index, burst index, stretch and breakinglength). The pulp was previously obtained by ethanolamine-soda-anthraquinone cooking of olive wood. A face-centred composite factor design was used to derive equations relating the pulp properties to the operational variables with a view to identifying the optimum operating conditions. The equations thus obtained reproduced the experimental results with errors less than 10% in all cases.The most suitable operating conditions were found to be alow temperature (60 ºC), a long time (180 min) and a highperborate concentration (5,5%). Because the pulp brightness achieved never exceeded 63% -not even under themost drastic conditions-, the process should not be used with one-step bleaching sequences. (Author)

Use of perborate in the bleaching of ethanolamine pulp from olive wood

International Nuclear Information System (INIS)

Ramos, E.; Torre, M.J. de la; Gutiérrez, J.C.

2016-01-01

In this work, we studied the influence of the bleacher concentration(2.5-5.5%), temperature (60-80 ºC) and time (60-180 min) on the reagent (perborate) consumption by dry pulp, various properties of the bleached pulp (yield, kappa number, brightness and viscosity/kappa numberratio), and some physical properties of paper sheets obtainedfrom it (tear index, burst index, stretch and breakinglength). The pulp was previously obtained by ethanolamine-soda-anthraquinone cooking of olive wood. A face-centred composite factor design was used to derive equations relating the pulp properties to the operational variables with a view to identifying the optimum operating conditions. The equations thus obtained reproduced the experimental results with errors less than 10% in all cases.The most suitable operating conditions were found to be alow temperature (60 ºC), a long time (180 min) and a highperborate concentration (5,5%). Because the pulp brightness achieved never exceeded 63% -not even under themost drastic conditions-, the process should not be used with one-step bleaching sequences. (Author)

FT-Raman spectra of cellulose and lignocellulose materials : “self-absorption” phenomenon and its implications for quantitative work

Science.gov (United States)

Umesh Agarwal; Nancy Kawai

2003-01-01

The phenomenon of “self-absorption” was found to exist in the FT-Raman spectra of cellulose and thermomechanical pulp (TMP), but not in the spectrum of milled wood lignin. For cellulose and TMP, the effect was responsible for reducing the intensity of the Raman bands in the C-H stretch region. Several factors including sampling position, sample thickness, and moisture...

PRODUCTION OF DISSOLVING GRADE PULP FROM ALFA

Directory of Open Access Journals (Sweden)

Baya Bouiri

2010-02-01

Full Text Available Alfa, also known as Stipa tenacissimaI or “halfa”, is grown in North Africa and south Spain. Due to its short fiber length, paper made from alfa pulp retains bulk and takes block letters well. In this study alfa was evaluated for bleached pulp production. Two cellulose pulps with different chemical compositions were pulped by a conventional kraft process. One sample was taken from the original alfa material and another from alfa that had been pretreated by diluted acid. The pulp produced from the pretreated alfa was bleached by the elemental-chlorine-free sequences DEPD and DEDP. The yield, Kappa number, brightness, and α- cellulose content of bleached and unbleached pulps were evaluated. The results showed that during the chemical pulping process, treated alfa cooked more easily than the original alfa. The treated alfa pulp also showed very good bleaching, reaching a brightness level of 94.8% ISO with a yield of 93.6% at an α-cellulose content 96.8(% with a DEDP bleaching sequence, compared to 83.2% ISO brightness level, 92.8% yield, and 95.1% α-cellulose content for bleached pulp with a DEPD bleaching sequence. Therefore, this alfa material could be considered as a worthwhile choice for cellulosic fiber supply.

A survey of present levels of radiocesium in Swedish pulp mill liquors and the implications for wood radiocesium transfer factors

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

1998-01-01

Assessments of the impact from radioactive fallout on the pulp industry and the accumulation processes for radionuclides in such industries, using wood and water as primary raw materials, have been conducted in previous studies. Hitherto, there is a general lack of data on present levels of radioactivity in pulp mill liquors apart from the few mills studied by [NILSSON (1992)] [RAVILA AND HOLM (1992)] [MANJON ET AL. (1996) and [KROSSHAVN ET AL. (1997)]. A survey was therefore initiated to describe and compare the present activity levels in pulp mill liquors from various mill locations in Sweden. The 137 Cs activity in pulp mill liquors were compared with the mill location and the deposition pattern of the Chernobyl fallout and nuclear weapons fallout. The large input of wood (approx. 2500 m 3 day -1 ) to an average Nordic Kraft mill and the relatively long-term retention time for radiocesium in the Kraft mill recovery cycle enables representative sampling of substances directly related to the activity concentration in wood

Formation of wood secondary cell wall may involve two type cellulose synthase complexes in Populus.

Science.gov (United States)

Xi, Wang; Song, Dongliang; Sun, Jiayan; Shen, Junhui; Li, Laigeng

2017-03-01

Cellulose biosynthesis is mediated by cellulose synthases (CesAs), which constitute into rosette-like cellulose synthase complexe (CSC) on the plasma membrane. Two types of CSCs in Arabidopsis are believed to be involved in cellulose synthesis in the primary cell wall and secondary cell walls, respectively. In this work, we found that the two type CSCs participated cellulose biosynthesis in differentiating xylem cells undergoing secondary cell wall thickening in Populus. During the cell wall thickening process, expression of one type CSC genes increased while expression of the other type CSC genes decreased. Suppression of different type CSC genes both affected the wall-thickening and disrupted the multilaminar structure of the secondary cell walls. When CesA7A was suppressed, crystalline cellulose content was reduced, which, however, showed an increase when CesA3D was suppressed. The CesA suppression also affected cellulose digestibility of the wood cell walls. The results suggest that two type CSCs are involved in coordinating the cellulose biosynthesis in formation of the multilaminar structure in Populus wood secondary cell walls.

Extraction of cellulose microcrystalline from galam wood for biopolymer

Science.gov (United States)

Ismail, Ika; Sa'adiyah, Devy; Rahajeng, Putri; Suprayitno, Abdi; Andiana, Rocky

2018-04-01

Consumption of plastic raw materials tends to increase, but until now the meet of the consumption of plastic raw are still low, even some are still imported. Nowadays, Indonesia's plastic needs are supported by petrochemicals where raw materials are still dependent abroad and petropolymer raw materials are derived from petroleum which will soon be depleted due to rising petroleum needs. Therefore, various studies have been conducted to develop natural fiber-based polymers that are biodegradable and abundant in nature. It is because the natural polymer production process is very efficient and very environmentally friendly. There have been many studies of biopolymers especially natural fiber-based polymers from plants, due to plants containing cellulose, hemicellulose and lignin. However, cellulose is the only one who has crystalline structures. Cellulose has a high crystality compared to amorphous lignin and hemicellulose. In this study, extracted cellulose as biopolymer and amplifier on composite. The cellulose is extracted from galam wood from East Kalimantan. Cellulose extraction will be obtained in nano / micro form through chemical and mechanical treatment processes. The chemical treatment of cellulose extraction is alkalinization process using NaOH solution, bleaching using NaClO2 and acid hydrolysis using sulfuric acid. After chemical treatment, ultrasonic mechanical treatment is made to make cellulose fibers into micro or nano size. Besides, cellulose results will be characterized. Characterization was performed to analyze molecules of cellulose compounds extracted from plants using Fourier Transformation Infra Red (FTIR) testing. XRD testing to analyze cellulose crystallinity. Scanning Electron Microscope (SEM) test to analyze morphology and fiber size.

Production of liquid transport fuel from cellulose material (wood). III Laboratory preparation of wood sugars and fermentation to ethanol and yeast

Energy Technology Data Exchange (ETDEWEB)

Whitworth, D A; Harwood, V D

1977-10-25

A laboratory procedure is described for hydrolyzing cellulose material to sugars by the use of hot sulfuric acid. The procedure has been used routinely for assessing raw materials. Raw materials used were radiata pine (fresh wood and decayed thinnings), pine needles, sawdust from old dumps, newspaper, cardboard, beech wood, and coconut wood. The neutralized sugar-liquors produced, supplemented with fertilizer grade nutrients, were fermented with bakers' yeast and gave near optimal conversion of hexoses to ethanol and of pentoses to protein biomass. From 100 g radiata pine (wood: bark mix 85:15) 25 ml (20 g) of ethanol and 2 g yeast biomass were routinely produced, although fermentation rates were lower than with pure sugars. The results, however, clearly showed that, by a hot dilute sulfure acid hydrolysis followed by a yeast fermentation process, cellulose resources avaliable in New Zealand are suitable for conversion to ethanol. 5 table, 1 figure.

Quantitative evaluation of the lignin protective effect on cellulose under γ irradiation of wood

International Nuclear Information System (INIS)

Skvortsov, S.V.; Klimentov, A.S.

1986-01-01

Changes in the degree of polymerization (D-barP-bar v ) of pine and spruce wood cellulose gamma-irradiated in- and outside the vegetable tissue are studied by the viscometric method. It has been shown that in the absorbed dose range of 0-100 kGy the protective effect of lignin on radiation-induced destruction of cellulose is reduced from 122 and 107 % to 4.5 and 3.4 %, respectively. At higher doses the mentioned effect is completely absent. It has been established that the destruction of wood cellulose in- and outside the plant tissue obeys the law of randomness, and finds its satisfactory description in the following equation: 1/D-barP-bar' v -1/D-barP-bar v 0 =KD α

CENTRAL KALIMANTAN’S FAST GROWING SPECIES: SUITABILITY FOR PULP AND PAPER

Directory of Open Access Journals (Sweden)

Danang Sudarwoko Adi

2015-04-01

Full Text Available Recent studies of fast growing species grown in PT. Sari Bumi Kusuma, Central Kalimantan, show that based on their fiber dimensions there are five species, namely Endospermum diadenum, Dillenia spp., Adinandra dumosa, Adiandra sp., and Nauclea junghuhnii with good potential for pulp and paper production. The fiber length of those five wood species are was more than 2,200 µm on average. This paper studies the physical properties, fiber dimensions and their chemical contents to predict the paper and pulp quality. The result shows that all of the species were classified in the medium to high density category. All species were classified into the first class quality for pulp and paper. Based on chemical contents, Dillenia sp. is the most suitable species due to its high value of holocellulose and a-cellulose, low lignin content, and its fiber length is about 3,119 µm on average. A. dumosa also has good opportunities because it had the longest fiber lengths (3,137 µm on average and high value of holocellulose, even though it has the highest lignin content. While Nuclea junghuhnii is less suitable due to low values of holocellulose and a-cellulose.

Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar

Energy Technology Data Exchange (ETDEWEB)

Tuskan, G.A.

2001-06-20

Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F2 progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar.

Potassium methyl siliconate-treated pulp fibers and their effects on wood plastic composites: Water sorption and dimensional stability

Science.gov (United States)

Cheng Piao; Zhiyong Cai; Nicole M. Stark; Charles J. Monlezun

2013-01-01

Potassium methyl siliconate (PMS) was investigated as a new nano modifier of wood fiber and wood flour to improve the compatibility between the fiber/flour and the plastic matrix in fiber reinforced plastic composites. Before injection molding, bleached and brown pulp fibers and mixed species wood flour were pretreated in PMS solutions. The morphology of the treated...

Characterizations of biodegradable epoxy-coated cellulose nanofibrils (CNF) thin film for flexible microwave applications

Science.gov (United States)

Hongyi Mi; Chien-Hao Liu; Tzu-Husan Chang; Jung-Hun Seo; Huilong Zhang; Sang June Cho; Nader Behdad; Zhenqiang Ma; Chunhua Yao; Zhiyong Cai; Shaoqin Gong

2016-01-01

Wood pulp cellulose nanofibrils (CNF) thin film is a novel recyclable and biodegradable material. We investigated the microwave dielectric properties of the epoxy coated-CNF thin film for potential broad applications in flexible high speed electronics. The characterizations of dielectric properties were carried out in a frequency range of 1–10 GHz. The dielectric...

Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar; FINAL

International Nuclear Information System (INIS)

Tuskan, G.A.

2001-01-01

Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F(sub 2) progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar

Cellulose nanocrystals as a reinforcing material for electrospun poly(methyl methacrylate) fibers: formation, properties and nanomechanical characterization

Science.gov (United States)

Hong Dong; Kenneth E. Strawhecker; James A. Snyder; Joshua A. Orlicki; Richard S. Reiner; Alan W. Rudie

2012-01-01

Uniform fibers composed of poly(methyl methacrylate) (PMMA) reinforced with progressively increasing contents of cellulose nanocrystals (CNCs), up to 41 wt% CNCs, have been successfully produced by electrospinning. The morphological, thermal and nanomechanical properties of the composite sub-micron fibers were investigated. The CNCs derived from wood pulp by sulfuric...

Flax fibers as a raw material: How to bleach efficiently a non-woody plant to obtain high-quality pulp

International Nuclear Information System (INIS)

Fillat, Ursula; Pepio, Montserrat; Vidal, Teresa; Roncero, M. Blanca

2010-01-01

Fiber crops constitute a good alternative to wood fiber for manufacturing pulp and paper. In fact, fiber plants like flax surpass wood fiber in some technical respects and also in the environmental benignity of their processing. In this work, flax fiber was subjected to environmentally friendly bleaching sequences in order to obtain a high-quality pulp. The totally chlorine-free sequences (TCF) used for this purpose (LE and LRE) included an enzyme treatment with laccase in the presence of HBT as mediator (L stage), an alkaline extraction (E stage) and a reductive treatment with NaBH 4 (R stage). The operating conditions for the L stage (laccase and HBT doses, reaction time and oxygen pressure) were optimised by using a sequential statistical plan to assess their influence on pulp properties after the E stage. Mathematical models accurately predicting brightness and kappa number in terms of the previous four variables were developed based on which the most influential factors were the laccase and HBT rates, and treatment time. By contrast, oxygen pressures of 0.2-0.6 MPa in the reactor had no effect on brightness or kappa number. The flax pulp obtained contained some oxidized cellulose that was partially degraded in the alkaline extraction step and reduced viscosity as a result. The viscosity loss associated with the presence of oxidized cellulose in the control and enzyme-treated pulp samples was efficiently recovered by using a reductive stage with sodium borohydride. Effluent was also analysed in order to assess the environmental impact of the process.

Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A [Hooli Oy, Kemi (Finland); Kuitto, P J [VTT Energy, Jyvaeskylae (Finland); Ranta, T [Finntech Ltd. Oy, Jyvaeskylae (Finland)

1997-12-31

Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A. [Hooli Oy, Kemi (Finland); Kuitto, P.J. [VTT Energy, Jyvaeskylae (Finland); Ranta, T. [Finntech Ltd. Oy, Jyvaeskylae (Finland)

1996-12-31

Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

Kinetics of Strong Acid Hydrolysis of a Bleached Kraft Pulp for Producing Cellulose Nanocrystals (CNCs)

Science.gov (United States)

Qianqian Wang; Xuebing Zhao; J.Y. Zhu

2014-01-01

Cellulose nanocrytals (CNCs) are predominantly produced using the traditional strong acid hydrolysis process. In most reported studies, the typical CNC yield is low (approximately 30%) despite process optimization. This study investigated the hydrolysis of a bleached kraft eucalyptus pulp using sulfuric acid between 50 and 64 wt % at temperatures of 35−80 °C...

Wood Pulp Digetster Wall Corrosion Investigation

Energy Technology Data Exchange (ETDEWEB)

Giles, GE

2003-09-18

The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

Alternative Technologies for Biofuels Production in Kraft Pulp Mills—Potential and Prospects

Directory of Open Access Journals (Sweden)

Esa Vakkilainen

2012-07-01

Full Text Available The current global conditions provide the pulp mill new opportunities beyond the traditional production of cellulose. Due to stricter environmental regulations, volatility of oil price, energy policies and also the global competitiveness, the challenges for the pulp industry are many. They range from replacing fossil fuels with renewable energy sources to the export of biofuels, chemicals and biomaterials through the implementation of biorefineries. In spite of the enhanced maturity of various bio and thermo-chemical conversion processes, the economic viability becomes an impediment when considering the effective implementation on an industrial scale. In the case of kraft pulp mills, favorable conditions for biofuels production can be created due to the availability of wood residues and generation of black liquor. The objective of this article is to give an overview of the technologies related to the production of alternative biofuels in the kraft pulp mills and discuss their potential and prospects in the present and future scenario.

Obtaining of Peracetic Cellulose from Oat Straw for Paper Manufacturing

Directory of Open Access Journals (Sweden)

Tetyana V. Zelenchuk

2017-10-01

Full Text Available Background. Development of technology for obtaining peracetic pulp from oat straw and its use in the production of one of the paper mass types. Objective. Determination of peracetic cooking technological parameters’ optimal values for oat straw peracetic cellulose quality indicators. Methods. The oat straw cooking was carried out with peracetic acid at 95 ± 1 °C from 90 to 180 min for hydromodulus 8:1 and 7:1, using a sodium tungstate catalyst. To determine the oat straw peracetic cellulose mechanical indexes, laboratory samples of paper weighing 70 g/m2 were made. Results. Technological parameters’ optimum values (temperature, cooking duration, hydromodulus, hydrogen peroxide and acetic acid concentration for the oat straw delignification process were established. It is shown that the sodium tungstate catalyst addition to the cooking solution at a rate of up to 1 % of the plant raw material weight helps to reduce the lignin content in cellulose to 15 %. A diagram of the cellulose yield dependence on its residual lignin content for various methods of non-wood plant material species delignification is constructed. The high efficiency of the peracetic method for obtaining cellulose from non-wood plant raw materials, in particular from oat straw, has been confirmed. It is determined that the obtained peracetic cellulose from oat straw has high mechanical indexes. Conclusions. Oat straw peracetic cellulose can be used for the production of paper and cardboard mass types, in particular wrapping paper.

Methods of pretreating comminuted cellulosic material with carbonate-containing solutions

Energy Technology Data Exchange (ETDEWEB)

Francis, Raymond

2012-11-06

Methods of pretreating comminuted cellulosic material with an acidic solution and then a carbonate-containing solution to produce a pretreated cellulosic material are provided. The pretreated material may then be further treated in a pulping process, for example, a soda-anthraquinone pulping process, to produce a cellulose pulp. The pretreatment solutions may be extracted from the pretreated cellulose material and selectively re-used, for example, with acid or alkali addition, for the pretreatment solutions. The resulting cellulose pulp is characterized by having reduced lignin content and increased yield compared to prior art treatment processes.

Heterogeneous studies in pulping of wood: Modelling mass transfer of alkali

OpenAIRE

Simão, João P. F.; Egas, Ana P. V.; Carvalho, M. Graça; Baptista, Cristina M. S. G.; Castro, José Almiro A. M.

2008-01-01

In this paper a heterogeneous lumped parameter model is proposed to describe the mass transfer of effective alkali during the kraft pulping of wood. This model, based on the spatial mean of the concentration profile of effective alkali along the chip thickness, enables the estimation of the effective diffusion coefficient that characterizes the internal resistance to mass transfer and the contribution of the external resistance to mass transfer which has often been neglected. http://www.sc...

Physicochemical and biochemical characterization of non-biodegradable cellulose in Miocene gymnosperm wood from the Entre-Sambre-et-Meuse, Southern Belgium

Energy Technology Data Exchange (ETDEWEB)

Lechien, Valerie; Rodriguez, Christian; Ongena, Marc; Hiligsmann, Serge; Thonart, Philippe [Liege Univ., Walloon Center of Industrial Biology, Gembloux (Belgium); Rulmont, Andre [Liege Univ., Chemistry Dept., Liege (Belgium)

2006-11-15

Specimens of Miocene fossil wood from the Entre-Sambre-et-Meuse karsts (southern Belgium) were examined using physicochemical and biochemical techniques in order to understand the reasons for the exceptional preservation of these fossilized remains after 15 million years. Structural and chemical changes were assessed by comparing the structural features of the fossil samples with those of their modern counterpart, Metasequoia. Solid state {sup 13} C nuclear magnetic resonance (NMR) and microscopic analysis showed good preservation of the cellulose structure in the fossil wood from the Florennes peat deposit. Despite the substantial cellulose fraction available in the fossil tissue, an enzymatic degradation test and a biochemical methane potential assay showed that the fossil cellulose could not be degraded by cellulases and anaerobic microorganisms usually involved in the biodegradation of organic matter. Moreover, the cellulose structure (crystallinity and surface area) seemed to have no effect on cellulose biodegradability in these Miocene fossil wood samples. On the basis of our observations, we suggest that the presence of a modified lignin structure could greatly influence cellulose preservation/biodegradability. (Author)

Water requirements of the pulp and paper industry

Science.gov (United States)

Mussey, Orville D.

1955-01-01

Water, of varied qualities, is used for several purposes in the manufacture of pulp and paper, as a vehicle for transporting the constituents of paper in the paper machines; as process water for cooking wood chips to make pulp; as a medium for heat transfer; and for washing the pulpwood, the woodpulp, and the machines that handle the pulp. About 3,200 million gallons of water was withdrawn from surface- and ground-water sources each day during 1950 for the use of the pulp and paper industry. This is about 4 percent of the total estimated industrial withdrawal of water in the Nation The paper industry in the United States has been growing at a rapid rate. It has increased about tenfold in the last 50 years and has doubled every 15 years. The 1950 production of paper was about 24 million tons, which amounts to about 85 percent of the domestic consumption. In 1950, the pulp mills of the country produced more than 14 million tons of woodpulp, which supplied about 85 percent of the demand by the paper mills and other industries. The remainder of the fiber for paper manufacture was obtained from imported woodpulp, from reclaimed wastepaper, and from other fibers including rags and straw. The nationwide paper consumption for 1955 has been estimated at 31,700,000 tons. Woodpulp is classified according to the process by which it is made. Every woodpulp has characteristics that are carried over into the many and diverse grades of paper. Groundwood pulp is manufactured by simply grinding up wood and refining the resulting product. Soda, sulfite, and sulfate pulps are manufactured by chemically breaking down the lignin that cements the cellulose of the wood together and removing, cleaning, and sometimes bleaching the resulting fibers. Some woodpulp is produced by other methods. Sulfate-pulp mills are increasing in number and in rated daily capacity and are manufacturing more than half of the present domestic production of woodpulp. Most of the newer and larger woodpulp mills

Utilization of cotton waste for regenerated cellulose fibres: Influence of degree of polymerization on mechanical properties.

Science.gov (United States)

De Silva, Rasike; Byrne, Nolene

2017-10-15

Cotton accounts for 30% of total fibre production worldwide with over 50% of cotton being used for apparel. In the process from cotton bud to finished textile product many steps are required, and significant cotton waste is generated. Typically only 30% of pre consumer cotton is recycled. Here we use cotton waste lint to produce regenerated cellulose fibres (RCF). We find the RCF from waste cotton lint had increased mechanical properties compared to RCF produced from wood pulp. We show that this is likely linked to the higher degree of polymerization (DP) of waste cotton lint. An ionic liquid is used to dissolve the cotton lint and the rheology of the spinning is measured. The properties of the RCF are characterized and compared to wood pulp RCF. Copyright © 2017 Elsevier Ltd. All rights reserved.

A survey of present levels of radiocesium in Swedish pulp mill liquors and the implications for wood radiocesium transfer factors. Using Kraft mill liquors as an indicator of wood radiocesium contamination

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

2000-01-01

A survey was initiated to depict and compare the present activity levels in pulp mill liquors from various mill locations. The 137 Cs levels in pulp mill liquors were compared with the mill location and the deposition pattern of the Chernobyl fallout and nuclear weapons fallout. The large input of wood (about 2500 m 3 per day) to an average Nordic Kraft mill and the relatively long-term retention time for radiocesium in the Kraft mill recovery cycle enables representative sampling of substances directly related to the activity concentration in wood. (author)

Valorization of residual Empty Palm Fruit Bunch Fibers (EPFBF) by microfluidization: production of nanofibrillated cellulose and EPFBF nanopaper.

Science.gov (United States)

Ferrer, Ana; Filpponen, Ilari; Rodríguez, Alejandro; Laine, Janne; Rojas, Orlando J

2012-12-01

Different cellulose pulps were produced from sulfur-free chemical treatments of Empty Palm Fruit Bunch Fibers (EPFBF), a by-product from palm oil processing. The pulps were microfluidized for deconstruction into nanofibrillated cellulose (NFC) and nanopaper was manufactured by using an overpressure device. The morphological and structural features of the obtained NFCs were characterized via atomic force and scanning electron microscopies. The physical properties as well as the interactions with water of sheets from three different pulps were compared with those of nanopaper obtained from the corresponding NFC. Distinctive chemical and morphological characteristics and ensuing nanopaper properties were generated by the EPFBF fibers. The NFC grades obtained compared favorably with associated materials typically produced from bleached wood fibers. Lower water absorption, higher tensile strengths (107-137 MPa) and elastic modulus (12-18 GPa) were measured, which opens the possibility for valorization of such widely available bioresource. Copyright © 2012 Elsevier Ltd. All rights reserved.

Nanomanufacturing metrology for cellulosic nanomaterials: an update

Science.gov (United States)

Postek, Michael T.

2014-08-01

The development of the metrology and standards for advanced manufacturing of cellulosic nanomaterials (or basically, wood-based nanotechnology) is imperative to the success of this rising economic sector. Wood-based nanotechnology is a revolutionary technology that will create new jobs and strengthen America's forest-based economy through industrial development and expansion. It allows this, previously perceived, low-tech industry to leap-frog directly into high-tech products and processes and thus improves its current economic slump. Recent global investments in nanotechnology programs have led to a deeper appreciation of the high performance nature of cellulose nanomaterials. Cellulose, manufactured to the smallest possible-size ( 2 nm x 100 nm), is a high-value material that enables products to be lighter and stronger; have less embodied energy; utilize no catalysts in the manufacturing, are biologically compatible and, come from a readily renewable resource. In addition to the potential for a dramatic impact on the national economy - estimated to be as much as $250 billion worldwide by 2020 - cellulose-based nanotechnology creates a pathway for expanded and new markets utilizing these renewable materials. The installed capacity associated with the US pulp and paper industry represents an opportunity, with investment, to rapidly move to large scale production of nano-based materials. However, effective imaging, characterization and fundamental measurement science for process control and characterization are lacking at the present time. This talk will discuss some of these needed measurements and potential solutions.

Use of high-boiling point organic solvents for pulping oil palm empty fruit bunches.

Science.gov (United States)

Rodríguez, Alejandro; Serrano, Luis; Moral, Ana; Pérez, Antonio; Jiménez, Luis

2008-04-01

Oil palm empty fruit bunches were used as an alternative raw material to obtain cellulosic pulp. Pulping was done by using high-boiling point organic solvents of decreased polluting power relative to classical (Kraft, sulphite) solvents but affording operation at similar pressure levels. The holocellulose, alpha-cellulose and lignin contents of oil palm empty fruit bunches (viz. 66.97%, 47.91% and 24.45%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using ethyleneglycol, diethyleneglycol, ethanolamine and diethanolamine under two different sets of operating conditions, namely: (a) a 70% solvent concentration, 170 degrees C and 90 min; and (b) 80% solvent, 180 degrees C and 150 min. The solid/liquid ratio was six in both cases. The amine solvents were found to provide pulp with better properties than did the glycol solvents. Ethanolamine pulp exhibited the best viscosity and drainage index (viz. 636 mL/g and 17 degrees SR, respectively), and paper made from it the best breaking length (1709 m), stretch (1.95%), burst index (0.98 kN/g) and tear index (0.33 mNm(2)/g). Operating costs can be reduced by using milder conditions, which provide similar results. In any case, the amines are to be preferred to the glycols as solvents for this purpose.

New and improved method of investigation using thermal tools for characterization of cellulose from eucalypts pulp

Energy Technology Data Exchange (ETDEWEB)

Lengowski, Elaine Cristina, E-mail: elainelengowski@yahoo.com.br [Laboratório de Anatomia e Qualidade da Madeira – LANAQM, Departamento de Engenharia e Tecnologia Florestal – DETF/Universidade Federal do Paraná, (UFPR), Curitiba, PR (Brazil); Magalhães, Washington Luiz Esteves, E-mail: washington.magalhaes@embrapa.br [Embrapa Florestas, Estrada da Ribeira km 111 P.O. Box 319, 83411-000 Colombo, PR (Brazil); Programa de Pós Graduação em Engenharia de Materiais – PIPE Universidade Federal do Paraná, (UFPR), Curitiba, PR (Brazil); Nisgoski, Silvana, E-mail: silnis@yahoo.com [Laboratório de Anatomia e Qualidade da Madeira – LANAQM, Departamento de Engenharia e Tecnologia Florestal – DETF/Universidade Federal do Paraná, (UFPR), Curitiba, PR (Brazil); Muniz, Graciela Inês Bolzon de, E-mail: graciela.ufpr@gmail.com [Laboratório de Anatomia e Qualidade da Madeira – LANAQM, Departamento de Engenharia e Tecnologia Florestal – DETF/Universidade Federal do Paraná, (UFPR), Curitiba, PR (Brazil); Satyanarayana, Kestur Gundappa [Embrapa Florestas, Estrada da Ribeira km 111 P.O. Box 319, 83411-000 Colombo, PR (Brazil); Lazzarotto, Marcelo, E-mail: marcelo.lazzarotto@embrapa.br [Embrapa Florestas, Estrada da Ribeira km 111 P.O. Box 319, 83411-000 Colombo, PR (Brazil)

2016-08-20

Highlights: • Cellulose was treated to modify its crystallinity. • Cellulose was characterized by X-ray diffraction to evaluate Segal’s index. • TGA and DTA with chemometric tools were used to predict Segal’s index. • MLR model was applied to predict XRD cellulose Segal’s index from TGA curves. • MLR model was applied to predict XRD cellulose Segal’s index from DTA curves. - Abstract: Despite cellulose being the most abundant biopolymer on earth and an important commodity, there is a lack of deeper knowledge about its structure as well as faster and more efficient characterization techniques. This paper presents preparation of nanocellulose from bleached cellulose pulp of Eucalyptus by chemical and mechanical pre-treatments, while the cellulose was given treatment to obtain a great range of crystallinity index. The nanocellulose is characterized by X-ray diffraction to evaluate Segal’s index while chemometric tools by TGA and DTA were used to predict Segal’s index. DTA curves, along with multivariate statistical model, presented better result than TGA. The coefficient of variation and standard error of prediction for the proposed models using external validation samples were in the range of 0.91–0.96 and 4.18–8.71, respectively. These successful mathematical models are discussed by correlating them with the observed characteristics of cellulose.

New and improved method of investigation using thermal tools for characterization of cellulose from eucalypts pulp

International Nuclear Information System (INIS)

Lengowski, Elaine Cristina; Magalhães, Washington Luiz Esteves; Nisgoski, Silvana; Muniz, Graciela Inês Bolzon de; Satyanarayana, Kestur Gundappa; Lazzarotto, Marcelo

2016-01-01

Highlights: • Cellulose was treated to modify its crystallinity. • Cellulose was characterized by X-ray diffraction to evaluate Segal’s index. • TGA and DTA with chemometric tools were used to predict Segal’s index. • MLR model was applied to predict XRD cellulose Segal’s index from TGA curves. • MLR model was applied to predict XRD cellulose Segal’s index from DTA curves. - Abstract: Despite cellulose being the most abundant biopolymer on earth and an important commodity, there is a lack of deeper knowledge about its structure as well as faster and more efficient characterization techniques. This paper presents preparation of nanocellulose from bleached cellulose pulp of Eucalyptus by chemical and mechanical pre-treatments, while the cellulose was given treatment to obtain a great range of crystallinity index. The nanocellulose is characterized by X-ray diffraction to evaluate Segal’s index while chemometric tools by TGA and DTA were used to predict Segal’s index. DTA curves, along with multivariate statistical model, presented better result than TGA. The coefficient of variation and standard error of prediction for the proposed models using external validation samples were in the range of 0.91–0.96 and 4.18–8.71, respectively. These successful mathematical models are discussed by correlating them with the observed characteristics of cellulose.

Changes in birch wood cellulose through the action of sulphuric acid during furfural production. 3. Isolation of cellulose compounds

Energy Technology Data Exchange (ETDEWEB)

Roze, I.M.; Vedernikov, N.A.

1981-01-01

The effect was studied of temperature (137-167 degrees C) and H/sub 2/SO/sub 4/ concentration (10-90%) in furfural production on the content of cellulose compounds and the degree of (hydrolytic) breakdown of difficultly-hydrolysed polysaccharides in the residual lignocellulose. Increasing temperature reduced cellulose yield and increased polysaccharide breakdown, especially in 10-30% H/sub 2/SO/sub 4/. A higher concentration of the same amount of H/sub 2/SO/sub 4/ reduced polysaccharide breakdown (by reducing the liquid/solid ratio), especially at a higher temperature, thereby enabling more cellulose to be recovered for further processing (e.g. wood hydrolysis). Results suggest that H/sub 2/SO/sub 4/ catalyzes the hydrolysis and dehydration processes differently. (Refs. 6).

The water footprint of wood for lumber, pulp, paper, fuel and firewood

Science.gov (United States)

Schyns, Joep F.; Booij, Martijn J.; Hoekstra, Arjen Y.

2017-09-01

This paper presents the first estimate of global water use in the forestry sector related to roundwood production for lumber, pulp, paper, fuel and firewood. For the period 1961-2010, we estimate forest evaporation at a high spatial resolution level and attribute total water consumption to various forest products, including ecosystem services. Global water consumption for roundwood production increased by 25% over 50 years to 961 × 109 m3/y (96% green; 4% blue) in 2001-2010. The water footprint per m3 of wood is significantly smaller in (sub)tropical forests compared to temperate/boreal forests, because (sub)tropical forests host relatively more value next to wood production in the form of other ecosystem services. In terms of economic water productivity and energy yield from bio-ethanol per unit of water, roundwood is rather comparable with major food, feed and energy crops. Recycling of wood products could effectively reduce the water footprint of the forestry sector, thereby leaving more water available for the generation of other ecosystem services. Intensification of wood production can only reduce the water footprint per unit of wood if the additional wood value per ha outweighs the loss of value of other ecosystem services, which is often not the case in (sub)tropical forests. The results of this study contribute to a more complete picture of the human appropriation of water, thus feeding the debate on water for food or feed versus energy and wood.

Isolation of cellulose microfibrils - An enzymatic approach

Directory of Open Access Journals (Sweden)

Sain, M.

2006-11-01

Full Text Available Isolation methods and applications of cellulose microfibrils are expanding rapidly due to environmental benefits and specific strength properties, especially in bio-composite science. In this research, we have success-fully developed and explored a novel bio-pretreatment for wood fibre that can substantially improve the microfibril yield, in comparison to current techniques used to isolate cellulose microfibrils. Microfibrils currently are isolated in the laboratory through a combination of high shear refining and cryocrushing. A high energy requirement of these procedures is hampering momentum in the direction of microfibril isolation on a sufficiently large scale to suit potential applications. Any attempt to loosen up the microfibrils by either complete or partial destruction of the hydrogen bonds before the mechanical process would be a step forward in the quest for economical isolation of cellulose microfibrils. Bleached kraft pulp was treated with OS1, a fungus isolated from Dutch Elm trees infected with Dutch elm disease, under different treatment conditions. The percentage yield of cellulose microfibrils, based on their diameter, showed a significant shift towards a lower diameter range after the high shear refining, compared to the yield of cellulose microfibrils from untreated fibres. The overall yield of cellulose microfibrils from the treated fibres did not show any sizeable decrease.

A benthic survey of Aliwal Shoal and assessment of the effects of a wood pulp effluent on the reef

International Nuclear Information System (INIS)

Schleyer, Michael H. . E-mail schleyer@ori.org.za; Heikoop, Jeffrey M.; Risk, Michael J.

2006-01-01

Aliwal Shoal lies south of Durban in South Africa and has been the subject of recent bathymetric, seafloor and benthic surveys. ANOVA of the biological data revealed that the biota were uniformly distributed on the reef with the exception of encrusting sponges and algae on rock. The variations in distribution of these biota were significant and, in the case of the encrusting sponges, appeared to be related to the discharge of a wood pulp effluent. Further evidence of this was suggested by stable isotope analyses of representative organisms. The encrusting sponges were recommended as good candidates for further monitoring of the effects of the wood pulp effluent on Aliwal Shoal as the effluent pipeline has been extended

Physical and Mechanical Properties of Cellulose Nanofibril Films from Bleached Eucalyptus Pulp by Endoglucanase Treatment and Microfluidization

Science.gov (United States)

Wangxia Wang; Ronald C. Sabo; Michael D. Mozuch; Phil Kersten; J. Y. Zhu; Yongcan Jin

2015-01-01

A GH5 hyperthermostable endoglucanase (Ph-GH5) from the archaeon Pyrococcus horikoshii and a commercial endoglucanase (FR) were used to treat bleached eucalyptus pulp (BEP) fibers to produce cellulose nanofibrils (CNF) and subsequently to CNF films. TEM imaging indicated that Ph-GH5 produced longer and more entangled CNF than FR with the same number...

INVESTIGATION OF AQUEOUS BIPHASIC SYSTEMS FOR THE SEPARATIONS OF LIGNINS FROM CELLULOSE IN THE PAPER PULPING PROCESS. (R826732)

Science.gov (United States)

In efforts to apply a polymer-based aqueous biphasic system (ABS) extraction to the paper pulping process, the study of the distribution of various lignin and cellulosic fractions in ABS and the effects of temperature on system composition and solute partitioning have been inv...

Increased profitability in cellulose production through more accurate measurement of the moisture content

International Nuclear Information System (INIS)

Anon.

1976-01-01

A general report on the project 'Dry Wood' is presented. In this project Noratom-Norcontrol A/S cooperate with the wood-pulp and paper factory Petersen and Soen in the application of Noratom's radiometric moisture gauge and their continuous weighing machine (densimeter) in the continuous measurement of the moisture content of wood chips in cellulose production. Conventional methods give an accuracy of π+ 2% and the objective of this method is an accuracy of π+ 1%. This would have a considerable economic significance. A test unit has been operating in the production line for a year and has attained the objective for short periods. Improved long term stability is the present problem. The system has process outputs which will facilitate future on-line computer process control. (JIW)

Comparison of stable carbon isotope ratios in the whole wood, cellulose and lignin of Oak tree-rings

CSIR Research Space (South Africa)

Loader, NJ

2003-08-01

Full Text Available The stable carbon isotope ratios (N13C) of whole wood, cellulose and acid-insoluble lignin from annual latewood increments of Quereus robur L., from modern and sub-fossil wood, were measured and their potential use as palaeo environmental indicators...

Chemical studies on oils derived from aspen poplar wood, cellulose, and an isolated aspen poplar lignin

Energy Technology Data Exchange (ETDEWEB)

Eager, R L; Pepper, J M; Roy, J C; Mathews, J F

1983-01-01

An initial study has been made of the chemical nature of the oil phase resulting from the conversion of aspen poplar wood, cellulose, and an isolated lignin from the aspen poplar as a result of their interactions with water and carbon monoxide in the presence of sodium carbonate at 360 degrees C. Gas chromatographic analysis of the sodium hydroxide soluble fractions from each substrate revealed similar spectra of alkyl-substituted phenols. The relative abundance of identified low molecular weight phenolic compounds decreased from lignin to wood to cellulose. This was in agreement with the known phenolic nature of lignin. As well, it confirmed the synthesis during reaction of such compounds from a carbohydrate substrate. Gas chromatographic analysis of the whole oils also revealed the presence in each case of several alkyl-substituted cyclopentanones whose relative abundance decreased from cellulose to wood to lignin. Silica gel column separation of the oils, after a charcoal treatment, followed by capillary gas chromatographic - mass spectrometric analyses of the resulting fraction indicated the presence of other higher molecular weight phenols, napthols, cycloalkanols, and polycyclic and long chain alkanes and alkenes.

Influence of High Shear Dispersion on the Production of Cellulose Nanofibers by Ultrasound-Assisted TEMPO-Oxidation of Kraft Pulp

Directory of Open Access Journals (Sweden)

Claude Daneault

2012-09-01

Full Text Available Cellulose nanofibers can be produced using a combination of TEMPO, sodium bromide (NaBr and sodium hypochlorite, and mechanical dispersion. Recently, this process has been the subject of intensive investigation. However, studies on the aspects of mechanical treatment of this process remain marginal. The main objective of this study is to evaluate the high shear dispersion parameters (e.g., consistency, stator-rotor gap, recirculation rate and pH and determine their influences on nanocellulose production using ultrasound-assisted TEMPO-oxidation of Kraft pulp. All nanofiber gels produced in this study exhibited rheological behaviors known as shear thinning. From all the dispersion parameters, the following conditions were identified as optimal: 0.042 mm stator-rotor gap, 200 mL/min recycle rate, dispersion pH of 7 and a feed consistency of 2%. High quality cellulose gel could be produced under these conditions. This finding is surely of great interest for the pulp and paper industry.

Fibrillar assembly of bacterial cellulose in the presence of wood-based hemicelluloses.

Science.gov (United States)

Penttilä, Paavo A; Imai, Tomoya; Sugiyama, Junji

2017-09-01

Composite materials mimicking the plant cell wall structure were made by culturing cellulose-producing bacteria together with secondary-wall hemicelluloses from wood. The effects of spruce galactoglucomannan (GGM) and beech xylan on the nanoscale morphology of bacterial cellulose were studied in the original, hydrated state with small-angle X-ray scattering (SAXS). The SAXS intensities were fitted with a model covering multiple levels of the hierarchical structure. Additional information on the structure of dried samples was obtained using scanning and transmission electron microscopy and infra-red spectroscopy. Both hemicelluloses induced a partial conversion of the cellulose crystal structure from I α to I β and a reduction of the cross-sectional dimensions of the cellulose microfibrils, thereby affecting also their packing into bundles. The differences were more pronounced in samples with xylan instead of GGM, and they became more significant with higher hemicellulose concentrations. Copyright © 2017 Elsevier B.V. All rights reserved.

Piezoelectric paper fabricated via nanostructured barium titanate functionalization of wood cellulose fibers.

Science.gov (United States)

Mahadeva, Suresha K; Walus, Konrad; Stoeber, Boris

2014-05-28

We have successfully developed hybrid piezoelectric paper through fiber functionalization that involves anchoring nanostructured BaTiO3 into a stable matrix with wood cellulose fibers prior to the process of making paper sheets. This is realized by alternating immersion of wood fibers in a solution of poly(diallyldimethylammonium chloride) PDDA (+), followed by poly(sodium 4-styrenesulfonate) PSS (-), and once again in PDDA (+), resulting in the creation of a positively charged surface on the wood fibers. The treated wood fibers are then immersed in a BaTiO3 suspension, resulting in the attachment of BaTiO3 nanoparticles to the wood fibers due to a strong electrostatic interaction. Zeta potential measurements, X-ray diffraction, and microscopic and spectroscopic analysis imply successful functionalization of wood fibers with BaTiO3 nanoparticles without altering the hydrogen bonding and crystal structure of the wood fibers. The paper has the largest piezoelectric coefficient, d33 = 4.8 ± 0.4 pC N(-1), at the highest nanoparticle loading of 48 wt % BaTiO3. This newly developed piezoelectric hybrid paper is promising as a low-cost substrate to build sensing devices.

Extraction and characterization of cellulose nano whiskers from balsa wood; Extracao e caracterizacao de nanocristais de celulose obtidos da madeira balsa

Energy Technology Data Exchange (ETDEWEB)

Morelli, Carolina L.; Bretas, Rosario E.S., E-mail: bretas@ufscar.br [Universidade Federal de Sao Carlos - UFSCar, Sao Carlos, SP (Brazil); Marconcini, Jose M. [Embrapa Instrumentacao, Sao Carlos, SP (Brazil); Pereira, Fabiano V. [Universidade Federal de Minas Gerais - UFMG, Belo Horizonte, MG (Brazil); Branciforti, Marcia C. [Universidade de Sao Paulo - USP, Sao Carlos, SP (Brazil)

2011-07-01

In this study cellulose nano whiskers were obtained from balsa wood. For this purpose, fibers of balsa wood were subjected to hydrolysis reactions for lignin and hemi cellulose digestion and acquisition of nano-scale cellulose. Cellulose nano crystals obtained had medium length and thickness of 176 nm and 7 nm respectively. Infrared spectroscopy and x-ray diffraction showed that the process used for extracting nano whiskers could digest nearly all the lignin and hemi cellulose from the balsa fiber and still preserve the aspect ratio and crystallinity, satisfactory enough for future application in polymer nano composites. Thermogravimetry showed that the onset temperature of thermal degradation of cellulose nano crystals (226 degree C) was higher than the temperature of the balsa fiber (215 degree C), allowing its use in molding processes with many polymers from the molten state.(author)

Investigation of ESEM/EDX to measure liquor penetration and diffusion in Eucalyptus grandis wood chips during kraft pulping

CSIR Research Space (South Africa)

Grzeskowiak, V

2011-01-01

Full Text Available Environmental scanning electron microscopy coupled with energy dispersive x-ray (ESEM/EDX) was optimised to measure the penetration and diffusion of cooking liquor into Eucalyptus grandis wood chips during kraft pulping. The moisture content...

Morphology and physical-chemical properties of celluloses obtained by different methods

Science.gov (United States)

Anpilova, A. Yu.; Mastalygina, E. E.; Mikhaylov, I. A.; Popov, A. A.; Kartasheva, Z. S.

2017-12-01

The morphology and structural characteristics of celluloses obtained by different methods were studied. The objects of the investigation are cellulose from pulp source, commercial celluloses produced by sodium and acid hydrolysis, laboratory produced cellulose from bleached birch kraft pulp, and cellulose obtained by thermooxidative catalytic treatment of maple leaves by peroxide. According to a complex analysis of cellulose characteristics, several types of celluloses were offered as modifying additives for polymers.

Infrared spectroscopy and thermal analysis of prepared cation exchangers from cellulosic materials

International Nuclear Information System (INIS)

Nada, A.M.A.; EI-Sherief, S.; Nasr, A.; Kamel, M.

2005-01-01

Different cation exchangers were prepared by incorporation of phosphate and sulfate groups into acid or alkali treated wood pulp. The molecular structure of these cation exchangers were followed by infrared spectroscopy and thermal degradation analysis technique. From infrared spectra, a new bands are seen at 1200 and 980 cm-1 in phosphorylated wood pulp due to the formation of C-O-P bond. Another bands were seen at 1400, 1200 and 980 cm-1 in phospho sulfonated wood pulp due to the formation of CO- P and C-O-S bonds. Also, it is seen from infrared spectra that the crystallinity index for acid treated wood pulp has a higher value than untreated and alkali treated wood pulp. On the other hand, the acid treated and phosphorylated acid treated wood pulp have a higher activation energy than untreated and phosphorylated alkali treated wood pulp

Understanding longitudinal wood fiber ultra-structure for producing cellulose nanofibrils using disk milling with diluted acid prehydrolysis

Science.gov (United States)

Yanlin Qin; Xueqing Qiu; Junyong Zhu

2016-01-01

Here we used dilute oxalic acid to pretreat a kraft bleached Eucalyptus pulp (BEP) fibers to facilitate mechanical fibrillation in producing cellulose nanofibrils using disk milling with substantial mechanical energy savings. We successfully applied a reaction kinetics based combined hydrolysis factor (CHFx) as a severity factor to quantitatively...

ANATOMICAL CHARACTERISTICS AND CHEMICAL PROPERTIES OF THE BRANCH-WOOD OF Schizolobium amazonicum DUCKE SPECIES AND ITS POTENTIAL USES

Directory of Open Access Journals (Sweden)

Yusup Amin

2013-10-01

Full Text Available The scale of forest degradation and deforestation in Indonesia has inspired the use of lesser-known wood species, which are potentially abundant and so far has not much been utilized. Utilization of these woods should be imposed not only of the stem wood but also of the branch-wood portions. Schizolobiumamazonicum Ducke treeis one of those lesser-known species, and growing fast with an MAIof3.68 cm/year.In Indonesia this species is only found in the Purwodadi Botanical Garden. A research was conducted to study the basic characteristics (anatomical aspects and chemical properties of the branch-wood portion of this species. The branch-wood materials were obtained from the Purwodadi Botanical Garden situated in Pasuruan (East Java. The specimens used were the first branch of the trunk (stem of nine-year old S. amazonicum tree (= 29.46 cm. The branch-wood samples were then examined for the anatomical aspects (macroscopic and microscopic characteristics and chemical properties (chemical composition. Results revealed that the anatomical properties of S.amazonicum branch-wood exhibited close similarities to those of sengon wood; it was light in appearance and white in color. Its fiber averaged about 1500 μm, and based on the fiber dimension's derived values the branch- wood fiber of this species was categorized into first-class quality for pulp and paper manufacture. Further, the chemical composition of this branch-wood compared favorably with that of sengon and mangium wood. The composition of extractive content thatsoluble in alcohol-benzene; lignin; holocellulose; and α-cellulose of this branch-wood were 2.46; 28.71; 80.64; and 50.47%, respectively. The overall assessment implied that the branch-wood portion of S.amazonicum tree affords favorable potential to be developed as raw material for pulp and paper manufacture. Also, considering that both sengon and mangium woods were already used in the pulp and paper industries as well as the trees are

Cellulose nanofiber extraction from grass by a modified kitchen blender

Science.gov (United States)

Nakagaito, Antonio Norio; Ikenaga, Koh; Takagi, Hitoshi

2015-03-01

Cellulose nanofibers have been used to reinforce polymers, delivering composites with strength that in some cases can be superior to that of engineering plastics. The extraction of nanofibers from plant fibers can be achieved through specialized equipment that demands high energy input, despite delivering extremely low yields. The high extraction cost confines the use of cellulose nanofibers to the laboratory and not for industrial applications. This study aims to extract nanofibers from grass by using a kitchen blender. Earlier studies have demonstrated that paper sheets made of blender-extracted nanofibers (after 5 min to 10 min of blending) have strengths on par with paper sheets made from commercially available cellulose nanofibers. By optimizing the design of the blender bottle, nanofibrillation can be achieved in shorter treatment times, reducing the energy consumption (in the present case, to half) and the overall extraction cost. The raw materials used can be extended to the residue straw of agricultural crops, as an alternative to the usual pulp fibers obtained from wood.

Integrated production method for wood fuel and pulp wood in Northern Finland; Integroitu energiapuun tuotanto-menetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A [Hooli Oy, Kemi (Finland); Ranta, T [VTT Energy, Jyvaeskylae (Finland)

1997-12-01

Hooli Oy, operating mainly in the Northern Finland has developed the production method suitable for bunch-processing of small wood. The mobile machine, consisting of delimber-debarker, and fuel fraction crusher units, produces debarked stemwood for pulping industry and branchwood-bark chips for thermal power stations. The basic method has been ready for demonstration and practical applications since in the beginning of year 1996. The objective of the project is to develop a method suitable for bundle processing of small wood, in which the trees are delimbed and debarked, and the formed waste wood is crushed using a machine unit, developed especially for this purpose. The method is based on utilisation of a separate delimbing-debarking unit, which operates separately from the pulpwood transportation chain, so the pulpwood transportations can be done at the proper time either as debarked roundwood or chips. Based on field experiments in 1995 - 1996, to attain the targets of the project looks promising. In 1997 there will happen technical modifications to the machine to improve the debarking results (target < 1 % bark content) of the bolts and to improve the logistic productivity of the whole production chain

In Vitro Osteogenic and Odontogenic Differentiation of Human Dental Pulp Stem Cells Seeded on Carboxymethyl Cellulose-Hydroxyapatite Hybrid Hydrogel.

Directory of Open Access Journals (Sweden)

Gabriella eTeti

2015-10-01

Full Text Available Stem cells from human dental pulp have been considered as an alternative source of adult stem cells in tissue engineering because of their potential to differentiate into multiple cell lineages.Recently, polysaccharide based hydrogels have become especially attractive as matrices for the repair and regeneration of a wide variety of tissues and organs. The incorporation of inorganic minerals as hydroxyapatite nanoparticles can modulate the performance of the scaffolds with potential applications in tissue engineering. The aim of this study was to verify the osteogenic and odontogenic differentiation of dental pulp stem cells (DPSCs cultured on a carboxymethyl cellulose—hydroxyapatite hybrid hydrogel. Human DPSCs were seeded on carboxymethyl cellulose—hydroxyapatite hybrid hydrogel and on carboxymethyl cellulose hydrogel for 1, 3, 5, 7, 14 and 21 days. Cell viability assay and ultramorphological analysis were carried out to evaluate biocompatibility and cell adhesion. Real Time PCR was carried out to demonstrate the expression of osteogenic and odontogenic markers. Results showed a good adhesion and viability in cells cultured on carboxymethyl cellulose—hydroxyapatite hybrid hydrogel, while a low adhesion and viability was observed in cells cultured on carboxymethyl cellulose hydrogel. Real Time PCR data demonstrated a temporal up-regulation of osteogenic and odontogenic markers in dental pulp stem cells cultured on carboxymethyl cellulose—hydroxyapatite hybrid hydrogel. In conclusion, our in vitro data confirms the ability of DPSCs to differentiate toward osteogenic and odontogenic lineages in presence of a carboxymethyl cellulose—hydroxyapatite hybrid hydrogel. Taken together, our results provide evidence that DPSCs and carboxymethyl cellulose—hydroxyapatite hybrid hydrogel could be considered promising candidates for dental pulp complex and periodontal tissue engineering.

X-ray Studies of Regenerated Cellulose Fibers Wet Spun from Cotton Linter Pulp in NaOH/Thiourea Aqueous Solutions

Energy Technology Data Exchange (ETDEWEB)

Chen,X.; Burger, C.; Fang, D.; Ruan, D.; Zhang, L.; Hsiao, B.; Chu, B.

2006-01-01

Regenerated cellulose fibers were fabricated by dissolution of cotton linter pulp in NaOH (9.5 wt%) and thiourea (4.5 wt%) aqueous solution followed by wet-spinning and multi-roller drawing. The multi-roller drawing process involved three stages: coagulation (I), coagulation (II) and post-treatment (III). The crystalline structure and morphology of regenerated cellulose fiber was investigated by synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques. Results indicated that only the cellulose II crystal structure was found in regenerated cellulose fibers, proving that the cellulose crystals were completely transformed from cellulose I to II structure during spinning from NaOH/thiourea aqueous solution. The crystallinity, orientation and crystal size at each stage were determined from the WAXD analysis. Drawing of cellulose fibers in the coagulation (II) bath (H{sub 2}SO{sub 4}/H{sub 2}O) was found to generate higher orientation and crystallinity than drawing in the post-treatment (III). Although the post-treatment process also increased crystal orientation, it led to a decrease in crystallinity with notable reduction in the anisotropic fraction. Compared with commercial rayon fibers fabricated by the viscose process, the regenerated cellulose fibers exhibited higher crystallinity but lower crystal orientation. SAXS results revealed a clear scattering maximum along the meridian direction in all regenerated cellulose fibers, indicating the formation of lamellar structure during spinning.

Soda-anthraquinone, kraft and organosolv pulping of holm oak trimmings.

Science.gov (United States)

Alaejos, J; López, F; Eugenio, M E; Tapias, R

2006-11-01

The operating conditions for an organosolv (ethyleneglycol) and two alkaline (soda-anthraquinone and kraft) processes for obtaining cellulose pulp and paper from holm oak (Quercus ilex) wood trimmings were optimized. A range of variation for each process variable (viz. temperature, cooking time and soda or ethyleneglycol concentration) was established and a central composite experimental design involving three independent variables at three different variation levels was applied. The results obtained with the three cooking processes used were compared and those provided by the kraft process were found to be the best. Thus, the tensile index values it provided (5.9-16.3 N m/g) were 23.7% and 41.5% better than those obtained with the soda-AQ and ethyleneglycol processes, respectively. Also, the kraft process provided the best burst index, brightness and kappa number values. Based on the optimum working ranges, the temperature and cooking time were the variables resulting in the most and least marked changes, respectively, in pulp properties.

Fungal bio-treatment of spruce wood with Trametes versicolor for pitch control: Influence on extractive contents, pulping process parameters, paper quality and effluent toxicity

NARCIS (Netherlands)

Beek, van T.A.; Kuster, B.; Claassen, F.W.; Tienvieri, T.; Bertaud, F.; Lennon, G.; Petit-Concil, M.; Sierra-Alvarez, R.

2007-01-01

Lipophilic low molar-mass constituents in wood chips for the paper industry result in low quality pulp, pitch deposition, and effluent toxicity. New biotechnological solutions such as fungal pre-treatment of wood chips can reduce pitch problems. This laboratory-scale study focuses on the potential

Effect of organosolv and soda pulping processes on the metals content of non-woody pulps.

Science.gov (United States)

González, M; Cantón, L; Rodríguez, A; Labidi, J

2008-09-01

In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).

Comparative study of percentage yield of pulp from various Nigerian ...

African Journals Online (AJOL)

user

also other applications like in the chemical industry. (Biermann, 1993). Therefore pulp is a very .... digester was maintained at an operating condition of. 170°C, pressure of 2 bars, with liquor to wood ratio of 4:1. Cooking ... The effects of different concentrations of pulping liquor on the yield of pulp from the wood species are ...

The economy of chip, tree section and short wood methods in the procurement of a pulp mill; Hake-, puu- ja puutavaralajimenetelmien taloudellisuus massatehtaan kuitu- ja energiapuun hankinnassa

Energy Technology Data Exchange (ETDEWEB)

Imponen, V [Metsaeteho Oy, Helsinki (Finland)

1997-12-01

Regional forest management plans for Finland`s private, non-industrial forestry indicate that first thinnings account for 13 % of the felling potential in these forests. The majority of first thinnings focus on pine-dominated stands. First-thinnings wood represents 29 % of the allowable cut consisting of pine pulpwood. However, small-diameter pine has not enjoyed great demand as raw material by the chemical pulp industry due to the high associated production costs and due to its inferior fibre properties when compared to large-sized softwood logs. Consequently, research and development work has been focused on the procurement, handling and usage of small-diameter wood, and especially of first-thinning pine. Both defibration and use as fuel are options when considering how to exploit small-diameter softwood raw material. Integrated procurement of industrial wood and wood fuel have improved the profitability of wood from thinnings in pulp manufacture and in energy generation at the mill. These methods would appear to be economic in regard to both the wood procurement of the pulp mills even at the present prices paid for alternative fuels. Advances in combustion technology and increased generation of electric power improve the competitiveness of methods based on the harvesting tree sections in comparison with the shortwood system yielding delimbed roundwood. The adoption of longer timber lorry-trailer combination as recognised by EU directives will have the effect of reducing the transportation costs for non-delimbed and partially delimbed wood. (orig.)

Pulping and paper properties of Palmyra palm fruit fibers

Directory of Open Access Journals (Sweden)

Waranyou Sridach

2010-05-01

Full Text Available Palmyra palm fruit fibers have the properties to be used as an alternative raw material of cellulosic pulps for papermaking.Acid and alkali pulping were investigated by using nitric acid and caustic soda on a laboratory scale, with the purpose of producing printing or writing grade pulp. The chemical composition of fiber strands from palmyra palm fruits were examined, such as holocellulose, cellulose, pentosan, lignin and extractives. The yields of acid and soda pulps were below 40%. The main physical and mechanical properties of hand sheets produced from acid and soda processes were evaluated on 80 g/m2 test sheets as functions of the following parameters: tensile index, tear index, and brightness. The mechanical properties of soda pulps were developed by twin-roll press while it was not necessary to fibrillate acidic pulps through the beating step. The soda pulp sheets presented a lower brightness than that of acidic pulp sheets. The mechanicaland physical properties of the acidic and alkaline pulps verified that they were of an acceptable quality for papermaking.

Determination of Mn, Fe, and Cu in chemically-treated wood pulps by the XRF addition method

Energy Technology Data Exchange (ETDEWEB)

Raemoe, J.; Klasila, T.; Piepponen, S. [VTT Chemical Technology (Finland); Sillanpaeae, M. [Oulu Univ. (Finland)

2001-08-01

A rapid X-ray fluorescence addition method has been developed for quantification of the technically most important metals in wood pulp matrix (Mn, Fe, and Cu). Pretreatment consisted of just two steps: first, acid was added to the sample to achieve homogeneous distribution of the metals; the pulp was then pressed lightly on to Mylar film. Total analysis time was less than 10 min. The concentration range investigated was up to 15 mg kg{sup -1} for Mn and up to 5 mg kg{sup -1} for Fe and Cu. Metal concentrations in Scandinavian pulps are not expected to exceed these amounts. The quantification limit was 2 mg kg{sup -1} for all three metals. The reproducibilities and repeatabilities were concentration-dependent and varied between 3 and 19% and between 1 and 17%, respectively. The squares of the linear correlation coefficients between measured intensity and added metal concentration were 0.994, 0.950, and 0.932 for Mn, Fe, and Cu, respectively. (orig.)

Optimization of pulping conditions of abaca. An alternative raw material for producing cellulose pulp.

Science.gov (United States)

Jiménez, L; Ramos, E; Rodríguez, A; De la Torre, M J; Ferrer, J L

2005-06-01

The influence of temperature (150-170 degrees C), pulping time (15-45 min) and soda concentration (5-10%) in the pulping of abaca on the yield, kappa, viscosity, breaking length, stretch and tear index of pulp and paper sheets, was studied. Using a factorial design to identify the optimum operating conditions, equations relating the dependent variables to the operational variables of the pulping process were derived that reproduced the former with errors lower than 25%. Using a high temperature, and a medium time and soda concentration, led to pulp that was difficult to bleach (kappa 28.34) but provided acceptable strength-related properties (breaking length 4728 m; stretch 4.76%; tear index 18.25 mN m2/g), with good yield (77.33%) and potential savings on capital equipment costs. Obtaining pulp amenable to bleaching would entail using more drastic conditions than those employed in this work.

Strong and Optically Transparent Films Prepared Using Cellulosic Solid Residue Recovered from Cellulose Nanocrystals Production Waste Stream

Science.gov (United States)

Qianqian Wang; J.Y. Zhu; John M. Considine

2013-01-01

We used a new cellulosic material, cellulosic solid residue (CSR), to produce cellulose nanofibrils (CNF) for potential high value applications. Cellulose nanofibrils (CNF) were produced from CSR recovered from the hydrolysates (waste stream) of acid hydrolysis of a bleached Eucalyptus kraft pulp (BEP) to produce nanocrystals (CNC). Acid hydrolysis greatly facilitated...

Utilization of steam- and explosion-decompressed aspen wood by some anaerobes

Energy Technology Data Exchange (ETDEWEB)

Khan, A W; Asther, M; Giuliano, C

1984-01-01

Tests made to study the suitability of using steam- and explosion-decompressed aspen wood as a substrate in anaerobic fermentations indicated that after washing with dilute NaOH it becomes less than 80% accessible to both mesophilic and thermophilic cellulolytic anaerobes and cellulases, compared with delignified, ball-milled pulp. After washing, this material was also suitable for the single-step conversion of cellulose to EtOH using cocultures consisting of cellulolytic and EtOH-producing saccharolytic anaerobes; and without and after washing by the use of cellulolytic enzymes and ethanologenic anaerobes.

Application of thermophilic enzymes and water jet system to cassava pulp.

Science.gov (United States)

Chaikaew, Siriporn; Maeno, Yuka; Visessanguan, Wonnop; Ogura, Kota; Sugino, Gaku; Lee, Seung-Hwan; Ishikawa, Kazuhiko

2012-12-01

Co-production of fermentable sugars and nanofibrillated cellulose from cassava pulp was achieved by the combination of thermophilic enzymes (endoglucanase, β-glucosidase, and α-amylase) and a new atomization system (Star Burst System; SBS), which employs opposing water jets. The SBS represents a key technology for providing cellulose nanofibers and improving the enzymatic saccharification of cassava pulp. Depending on the enzymes used, the production of glucose from cassava pulp treated with the SBS was 1.2- to 2.5-fold higher than that from pulp not treated with the SBS. Nanofibrillated cellulose with the gel-like property in suspension was produced (yield was over 90%) by α-amylase treatment, which completely released trapped starch granules from the fibrous cell wall structure of cassava pulp pretreated with the SBS. The SBS provides an environmentally low-impact pretreatment system for processing biomass material into value-added products. Copyright © 2012 Elsevier Ltd. All rights reserved.

Influence of Cellulosic Fibres on the Physical Properties of Fibre Cement Composites

Science.gov (United States)

Hospodarova, V.; Stevulova, N.; Vaclavik, V.; Dvorsky, T.

2017-10-01

Nowadays, there are new approaches directing to processing of non-conventional fibre-cement composites for application in the housing construction. Vegetable cellulosic fibres coming from natural resources used as reinforcement in cost-effective and environmental friendly building products are in the spotlight. The applying of natural fibres in cement based composites is narrowly linked to the ecological building sector, where a choice of materials is based on components including recyclable, renewable raw materials and low-resource manufacture techniques. In this paper, two types of cellulosic fibres coming from wood pulp and recycled waste paper with 0.2%; 0.3% and 0.5% of fibre addition into cement mixtures were used. Differences in the physical characteristics (flowability, density, coefficient of thermal conductivity and water absorbability) of 28 days hardened fibre-cement composites are investigated. Addition of cellulosic fibres to cement mixture caused worsening the workability of fresh mixture as well as absorbability of hardened composites due to hydrophilic nature of biomaterial, whereas density and thermal conductivity of manufactured cement based fibre plaster are enhanced. The physical properties of cement plasters based on cellulosic fibres depend on structural, physical characteristics of cellulosic fibres, their nature and processing.

An XPS round robin investigation on analysis of wood pulp fibres and filter paper

Science.gov (United States)

Johansson, Leena-Sisko; Campbell, J. M.; Fardim, Pedro; Hultén, Anette Heijnesson; Boisvert, Jean-Philippe; Ernstsson, Marie

2005-06-01

X-ray photoelectron spectroscopy (XPS) has been applied to pulp and paper research for decades. However, there has been no attempt to standardise or even systematically compare experimental and analysis procedures, even though it is known that fibrous, nature-derived and insulating fibre materials pose remarkable challenges to reliable surface analysis. The experimental problems are mainly linked with neutralisation, energy resolution, contamination and X-ray induced degradation. We have tested applicability, reliability and reproducibility of XPS analysis on real pulp samples with varying lignin and extractives contents in a small round robin investigation. We also tested the instrumental set-ups with an acetone-extracted filter paper, used as a reference sample. The data, collected at four different laboratories with state-of-the-art instruments indicate that reproducible results can be obtained, despite minor differences in experimental and analysis procedures. However, we found that a specified sample handling procedure and limited X-ray exposure are crucial for reproducible, reliable data. Based on the round robin data we recommend dose restricted monochromatic measurements, a cellulosic in situ reference and a consistent sample handling procedure. The data confirms that a paper-based reference material and the correlation of high-resolution C 1s data with O/C atomic ratios can be used in testing instruments and experimental set-ups for pulp and paper materials.

Análise do mercado brasileiro de celulose, 1969-2005 Analysis of the wood pulp Brazilian market, 1969 - 2005

Directory of Open Access Journals (Sweden)

Naisy Silva Soares

2009-06-01

Full Text Available O segmento de celulose e papel contribui de forma significativa para a economia brasileira. O conhecimento da estrutura do mercado de celulose é fundamental para fins de planejamento da produção, comercialização e previsão para o setor. Este trabalho teve como objetivo principal especificar e estimar a oferta e demanda brasileira de celulose, bem como a oferta e a demanda de exportação, no período de 1969 a 2005. Os resultados, usando o método dos Mínimos Quadrados de Dois Estágios (MQ2E, indicaram que a oferta e a demanda interna de celulose, bem como a oferta e a demanda de exportação, são preço-inelástico. A demanda interna é inelástica com relação à renda. Já a demanda de exportação é elástica com relação à renda. A oferta interna é mais sensível a variações no preço das máquinas e equipamentos. A oferta de exportação é sensível a variações na produção e no consumo interno e a demanda de exportação, a variações na renda dos países importadores.The wood pulp and paper sector contributes significantly for the Brazilian economy. The knowledge of the wood pulp market structure is important for production planning, commercialization and forecast for the sector. The main objective of the present study it to specify and estimate the domestic supply and demand of wood pulp, as well as the export supply and demand functions, in the period from 1969 to 2005. The results provided by' the two-stage least squares method (TSLS indicated that domestic and export supply and demand of wood pulp are price inelastic. The domestic demand is inelastic in relation to income while the export demand is elastic in relation to income. The domestic supply is more affected by changes in machinery and equipment prices. The export supply is affected by changes in production and domestic demand while the export demand is affected by changes in the income of the importing countries.

MINERAL ELEMENTS IN WOODS OF EUCALYPTUS AND BLACK WATTLE AND ITS INFLUENCE IN A BLEACHED KRAFT PULP MILL

Directory of Open Access Journals (Sweden)

André Fredo

2009-09-01

Full Text Available Effluents are one of the most important problems in a pulp mill regarding to environmental subjects. With the purpose to reduce them, the mills are closing the internal cycles and reducing the water consumption. The wood, as the most significant source of non-process elements to the system, is responsible for some troubles to the industrial process. With the aim of evaluating their intake and to offer some informations for closing the loop, the contents of Al, Ca, Cu, Fe, K, Mg, Mn, Na, Ni, and Si were analysed in Acacia mearnsii, Eucalyptus dunnii, Eucalyptus globulus globulus, Eucalyptus grandis and Eucalyptus saligna woods. Wood samples were prepared by oven burning and acidic digestion methods, following analysis by ICP (inductively coupled plasm. Using also the results from silvicultural evaluation of trees and stands, they were calculated which elements were carried out from the site in larger amounts (K, Ca, Na, Al, Mn and Si and the species which exported largest amount of these elements (Eucalyptus dunnii and Eucalyptus globulus. The species with lower growth were Eucalyptus globulus and Eucalyptus dunnii, that leads to a bigger elements input and more potential industrial troubles. It was observed a range of 3.8 (Eucalyptus grandis up to 6 (Eucalyptus dunnii kg of analised mineral elements introduced to the process per ton of umbleached pulp produced. The Acacia mearnsii showed the lower level for Fe, Mn and Ni, being useful for oxygen, ozone and peroxide bleaching. The silicon observed in woods was in low concentration although the high values of this element in industrial liquor cycle. This leads to state that there is some contamination with soil when harvesting and handling the wood. Special care must be taken with both high ash and high mineral elements species, such as Eucalyptus dunnii and Eucalyptus globulus.

Low Temperature Soda-Oxygen Pulping of Bagasse

OpenAIRE

Fengxia Yue; Ke-Li Chen; Fachuang Lu

2016-01-01

Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum coo...

Highly Stable, Functional Hairy Nanoparticles and Biopolymers from Wood Fibers: Towards Sustainable Nanotechnology.

Science.gov (United States)

Sheikhi, Amir; Yang, Han; Alam, Md Nur; van de Ven, Theo G M

2016-07-20

Nanoparticles, as one of the key materials in nanotechnology and nanomedicine, have gained significant importance during the past decade. While metal-based nanoparticles are associated with synthetic and environmental hassles, cellulose introduces a green, sustainable alternative for nanoparticle synthesis. Here, we present the chemical synthesis and separation procedures to produce new classes of hairy nanoparticles (bearing both amorphous and crystalline regions) and biopolymers based on wood fibers. Through periodate oxidation of soft wood pulp, the glucose ring of cellulose is opened at the C2-C3 bond to form 2,3-dialdehyde groups. Further heating of the partially oxidized fibers (e.g., T = 80 °C) results in three products, namely fibrous oxidized cellulose, sterically stabilized nanocrystalline cellulose (SNCC), and dissolved dialdehyde modified cellulose (DAMC), which are well separated by intermittent centrifugation and co-solvent addition. The partially oxidized fibers (without heating) were used as a highly reactive intermediate to react with chlorite for converting almost all aldehyde to carboxyl groups. Co-solvent precipitation and centrifugation resulted in electrosterically stabilized nanocrystalline cellulose (ENCC) and dicarboxylated cellulose (DCC). The aldehyde content of SNCC and consequently surface charge of ENCC (carboxyl content) were precisely controlled by controlling the periodate oxidation reaction time, resulting in highly stable nanoparticles bearing more than 7 mmol functional groups per gram of nanoparticles (e.g., as compared to conventional NCC bearing AFM), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) attested to the rod-like morphology. Conductometric titration, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), dynamic light scattering (DLS), electrokinetic-sonic-amplitude (ESA) and acoustic attenuation spectroscopy shed light on the superior properties of these

Obtaining value prior to pulping with diethyl oxalate and oxalic acid

Science.gov (United States)

W.R. Kenealy; E. Horn; C.J. Houtman; J. Laplaza; T.W. Jeffries

2007-01-01

Pulp and paper are converted to paper products with yields of paper dependent on the wood and the process used. Even with high yield pulps there are conversion losses and with chemical pulps the yields approach 50%. The portions of the wood that do not provide product are either combusted to generate power and steam or incur a cost in waste water treatment. Value prior...

Biocomposite of Cassava Starch Reinforced with Cellulose Pulp Fibers Modified with Deposition of Silica (SiO2 Nanoparticles

Directory of Open Access Journals (Sweden)

Joabel Raabe

2015-01-01

Full Text Available Eucalyptus pulp cellulose fibers were modified by the sol-gel process for SiO2 superficial deposition and used as reinforcement of thermoplastic starch (TPS. Cassava starch, glycerol, and water were added at the proportion of 60/26/14, respectively. For composites, 5% and 10% (by weight of modified and unmodified pulp fibers were added before extrusion. The matrix and composites were submitted to thermal stability, tensile strength, moisture adsorption, and SEM analysis. Micrographs of the modified fibers revealed the presence of SiO2 nanoparticles on fiber surface. The addition of modified fibers improved tensile strength in 183% in relation to matrix, while moisture adsorption decreased 8.3%. Such improvements were even more effective with unmodified fibers addition. This result was mainly attributed to poor interaction between modified fibers and TPS matrix detected by SEM analysis.

Prospect of trema orientalis as a pulping raw material in bangladesh

International Nuclear Information System (INIS)

Jahan, M.S.

2013-01-01

The pulp and paper industry in Bangladesh is looking for new raw materials with high productivity per hectare. Currently, bamboo and Gmelina arborea are the main pulping raw materials for the pulp and paper industry of the country. Trema orientalis is one of the fastest growing woods in the tropical region. This paper reviews the literature on the topic, in particular, related to the chemical, morphological and physical properties of T. orientalis and its suitability for pulping. In addition, the advantages and disadvantages of various ulping processes proposed in the literature were critically analyzed. It was concluded that T. orientalis is a potential pulp wood for the Bangladesh pulp and paper industry. (author)

Pectin Methylesterase Genes Influence Solid Wood Properties of Eucalyptus pilularis1[C][W][OA

Science.gov (United States)

Sexton, Timothy R.; Henry, Robert J.; Harwood, Chris E.; Thomas, Dane S.; McManus, Luke J.; Raymond, Carolyn; Henson, Michael; Shepherd, Mervyn

2012-01-01

This association study of Eucalyptus pilularis populations provides empirical evidence for the role of Pectin Methylesterase (PME) in influencing solid wood characteristics of Eucalyptus. PME6 was primarily associated with the shrinkage and collapse of drying timber, which are phenotypic traits consistent with the role of pectin as a hydrophilic polysaccharide. PME7 was primarily associated with cellulose and pulp yield traits and had an inverse correlation with lignin content. Selection of specific alleles in these genes may be important for improving trees as sources of high-quality wood products. A heterozygote advantage was postulated for the PME7 loci and, in combination with haplotype blocks, may explain the absence of a homozygous class at all single-nucleotide polymorphisms investigated in this gene. PMID:22052017

Biohydrogen, bioelectricity and bioalcohols from cellulosic materials

Energy Technology Data Exchange (ETDEWEB)

Nissila, M.

2013-03-01

The demand for renewable energy is increasing due to increasing energy demand and global warming associated with increasing use of fossil fuels. Renewable energy can be derived from biological production of energy carriers from cellulosic biomass. These biochemical processes include biomass fermentation to hydrogen, methane and alcohols, and bioelectricity production in microbial fuel cells (MFCs). The objective of this study was to investigate the production of different energy carriers (hydrogen, methane, ethanol, butanol, bioelectricity) through biochemical processes. Hydrogen production potential of a hot spring enrichment culture from different sugars was determined, and hydrogen was produced continuously from xylose. Cellulolytic and hydrogenic cultures were enriched on cellulose, cellulosic pulp materials, and on silage at different process conditions. The enrichment cultures were further characterized. The effect of acid pretreatment on hydrogen production from pulp materials was studied and compared to direct pulp fermentation to hydrogen. Electricity and alcohol(s) were simultaneously produced from xylose in MFCs and the exoelectrogenic and alcohologenic enrichment cultures were characterized. In the end, the energy yields obtained from different biochemical processes were determined and compared. In this study, cultures carrying out simultaneous cellulose hydrolysis and hydrogen fermentation were enriched from different sources at different operational conditions. These cultures were successfully utilized for cellulose to hydrogen fermentation in batch systems. Based on these results further research should be conducted on continuous hydrogen production from cellulosic materials.

Scale up of ethanol production using pulp mill wastewater sludge by cellulase and saccharomyces cerevisiae

International Nuclear Information System (INIS)

Kunchada Sangasintu; Petchporn Chawakitchareon

2010-01-01

This study aimed to evaluate the potential use of pulp mill wastewater sludge as substrate in ethanol production. The simultaneous saccharification and fermentation process was conducted by using Saccharomyces cerevisiae TISTR 5339 under optimum proportion of cellulase and pulp mill wastewater sludge. The ethanol production from cellulosic materials in simultaneous saccharification and fermentation needs cooperation between cellulase and yeast. The cellulase hydrolyzes cellulose to sugar while yeast utilizes sugar to produce ethanol. The pulp mill wastewater sludge has an average content of 73.3 % hemi cellulose, 67.1 % alpha cellulose, 4.7 % beta cellulose and 1.4 % gamma cellulose. The experimental results indicated that the volume of the ethanol tend to increase with time, providing the maximum ethanol yield of 0.69 g/g on the 7"t"h day, the last day of the experiment. The ethanol production was scaled up in 5 L fermentor under optimum proportion and increased the fermentation period. It was found that the ethanol production gave the maximum ethanol yield of 1.14 g/g on the 9"t"h day of the totally 13 days experimentation. These results showed that the cellulose from pulp mill wastewater sludge was as effective substrate for ethanol production and alternative energy for the future. (author)

A xylanase-aided enzymatic pretreatment facilitates cellulose nanofibrillation.

Science.gov (United States)

Long, Lingfeng; Tian, Dong; Hu, Jinguang; Wang, Fei; Saddler, Jack

2017-11-01

Although biological pretreatment of cellulosic fiber based on endoglucanases has shown some promise to facilitate cellulose nanofibrillation, its efficacy is still limited. In this study, a xylanase-aided endoglucanase pretreatment was assessed on the bleached hardwood and softwood Kraft pulps to facilitate the downstream cellulose nanofibrillation. Four commercial xylanase preparations were compared and the changes of major fiber physicochemical characteristics such as cellulose/hemicellulose content, gross fiber properties, fiber morphologies, cellulose accessibility/degree of polymerization (DP)/crystallinity were systematically evaluated before and after enzymatic pretreatment. It showed that the synergistic cooperation between endoglucanase and certain xylanase (Biobrite) could efficiently "open up" the hardwood Kraft pulp with limited carbohydrates degradation (cellulose nanofibrillation during mild sonication process (90Wh) with more uniform disintegrated nanofibril products (50-150nm, as assessed by scanning electron microscopy and UV-vis spectroscopy). Copyright © 2017 Elsevier Ltd. All rights reserved.

A LARCH BIOREFINERY: INFLUENCE OF WASHING AND PS CHARGE ON PRE-EXTRACTION PSAQ PULPING

Directory of Open Access Journals (Sweden)

Hanna S. Hörhammer

2012-06-01

Full Text Available This study deals with a biorefinery concept based on larch wood. Wood chips of Siberian larch (Larix sibirica Lebed. were treated with water before pulping at the optimal pre-extraction (PE condition of 150 °C and 90 minutes. Through PE, about 12.4% of the wood mass is dissolved, mainly from the arabinogalactan hemicellulose component. Fermentation of the hemicellulose-rich larch extract with Bacillus coagulans resulted in consumption of all C6 and C5 sugars and produced lactic acid in high yield. PE before pulping resulted in lower (4 to 5% pulp yield than for control kraft pulps. However, the pulp yield loss may be reduced by addition of polysulfide (PS and anthraquinone (AQ. The present study focuses on the effect of the degree of washing of the extracted chips and that of the PS charge in PSAQ pulping on the final properties of the pulp. Three different levels of washing and three different PS charges were tested. The characteristics of the extract, wash water, pulp, and black liquor samples were determined. The amount of sugars in the combined stream of collected extract and wash water obtained by mild washing was 10.2% on o.d. wood.

Physical and mechanical properties of microcrystalline cellulose prepared from local agricultural residues

International Nuclear Information System (INIS)

El-Sakhawy, M.M.; Hassan, M.L.

2005-01-01

Microcrystalline cellulose (MCC) was prepared from local agricultural residues, namely, bagasse, rice straw, and cotton stalks bleached pulps. Hydrolysis of bleached pulps was carried out using hydrochloric or sulfuric acid to study the effect of the acid used on the properties of produced microcrystalline cellulose such as degree of polymerization (DP), crystallinity index (CrI), crystallite size, bulk density, particle size, and thermal stability. The mechanical properties of tablets made from microcrystalline cellulose of the different agricultural residues were tested and compared to commercial grade MCC. The use of rice straw pulp in different proportions as a source of silica to prepare silicified microcrystalline cellulose (SMCC) was carried out. The effect of the percent of silica on the mechanical properties of tablets before and after wet granulation was tested

Physical and mechanical properties of microcrystalline cellulose prepared from local agricultural residues

Energy Technology Data Exchange (ETDEWEB)

El-Sakhawy, M M; Hassan, M L [Cellulose and Paper Dept., National Research Center, Dokki, Cairo (Egypt)

2005-07-01

Microcrystalline cellulose (MCC) was prepared from local agricultural residues, namely, bagasse, rice straw, and cotton stalks bleached pulps. Hydrolysis of bleached pulps was carried out using hydrochloric or sulfuric acid to study the effect of the acid used on the properties of produced microcrystalline cellulose such as degree of polymerization (DP), crystallinity index (CrI), crystallite size, bulk density, particle size, and thermal stability. The mechanical properties of tablets made from microcrystalline cellulose of the different agricultural residues were tested and compared to commercial grade MCC. The use of rice straw pulp in different proportions as a source of silica to prepare silicified microcrystalline cellulose (SMCC) was carried out. The effect of the percent of silica on the mechanical properties of tablets before and after wet granulation was tested.

Wood and Paper Manufacturing Sectors

Science.gov (United States)

Find EPA regulatory information for the wood product and paper manufacturing sectors, including paper, pulp and lumber. Information includes NESHAPs and effluent guidelines for pulp and paper rulemaking, and compliance guidelines

Mechanical properties of cellulose nanomaterials studied by contact resonance atomic force microscopy

Science.gov (United States)

Ryan Wagner; Robert J. Moon; Arvind Raman

2016-01-01

Quantification of the mechanical properties of cellulose nanomaterials is key to the development of new cellulose nanomaterial based products. Using contact resonance atomic force microscopy we measured and mapped the transverse elastic modulus of three types of cellulosic nanoparticles: tunicate cellulose nanocrystals, wood cellulose nanocrystals, and wood cellulose...

Nanofibrillated cellulose (NFC) as a potential reinforcement for high performance cement mortar composites

OpenAIRE

Ardanuy Raso, Mònica; Claramunt Blanes, Josep; Arévalo Peces, Raquel; Parés Sabatés, Ferran; Aracri, Elisabetta; Vidal Lluciá, Teresa

2012-01-01

In this work, nanofibrillated cellulose (NFC) has been evaluated as a potential reinforcement for cement mortar composites. Two types of vegetable fibres with different composition and properties (cellulose content and microfibrillar angle), sisal, and cotton linters pulps, were initially characterized in order to assess their reinforcement capability. Sisal pulp was found to be most suitable as reinforcement for their brittle cementitious matrix. Nanofibrillated cellulose was produced by th...

Increase of alcohol yield per ton of pulp

Energy Technology Data Exchange (ETDEWEB)

Sokolov, B N

1957-01-01

Digestion processes of cellulose were studied under production conditions. When the digestion was carried out with acid having 5.2% total SO/sub 2/ and 0.92% CaO, the concentration of total sugars in the spent liquor was 1.8 to 2.5%. When the acidity was reduced to 4.8% total SO/sub 2/ and 0.82% CaO, all other conditions being the same, the sugar concentration in the spent liquor increased to 3.0 to 3.7%. The importance of the acid strength and CaO content of the cooking liquor was further demonstrated at the end of 1955. At that time the total SO/sub 2/ in the acid rose to 8% while the amount of CaO remained practically the same-0.85 to 0.90%. These conditions permitted an increase in the amount of ships by 25 to 30%, which further changed the ratio CaO: wood and created conditions favorable for an improved yield of sugar. The increase in the activity of the acid was reflected favorably in the degree of hydrolysis of the hemicelluloses and in the degree to which the oligosaccharides or polysaccharides were hydrolyzed to simple sugars. At that time the yield of alcohol reached 53 1/ton of unbleached pulp. The process was further improved in 1956 by the use of successive washings; at the end of the digestion period the concentrated spent liquor was piped to the alcohol unit. The yield of alcohol reached 59.4 1/ton of pulp. Sugar recovery from the tank was 92.5% of that theoretically possible. Further improvements resulted by saturating the wood chips with acid under variable pressures. As a result, the base of the cooking acid was reduced to 0.7 to 0.72% and, at the end of the process the liquor contained 0.03 to 0.06% CaO instead of 0.2 to 0.18%. The alcohol yield/ton of pulp then rose to 66.8 l.

Effect of Urea Addition on Soda Pulping of Oak Wood

OpenAIRE

Cho, Nam-Seok; Matsumoto, Yuji; Cho, Hee-Yeon; Shin, Soo-Jeong; Oga, Shoji

2008-01-01

Many studies have been conducted to find a sulfur-free additive for alkaline pulping liquors that would have an effect similar to that of sulfide in kraft pulping. Some reagents that partially fulfill this role have been found, but they are too expensive to be used in the quantities required to make them effective. As an alternative method to solve air pollution problem and difficulty of pulp bleaching of kraft pulping process, NaOH-Urea pulping was applied. The properties of NaOH-Urea pul...

Improvement in Dissolution of Cotton Pulp with Ionic liquid by the Electron Beam Treatment

International Nuclear Information System (INIS)

Lee, Won Sil; Jung, Wong Gi; Sung, Yong Joo

2013-01-01

Electron beam treatment was applied for improving dissolution of cotton pulp with ionic liquids. Two ionic liquids, 1-allyl-3-methylimidazolium chloride ([Amim]Cl]: AC) and 1,3-dimethylimidzolium methlphosphite ([Dmim][(MeO)(H)PO2]: Me) were used for this experiment. Treatment with electron beams up to dose of 400 kGy resulted in the increase of hot water extract and alkali extract of cotton pulp and the great reduction in the molecular weight of cellulose. For the dissolution of cotton pulp with two ionic liquids, the electron beam treated samples showed faster dissolution. The dissolved cellulose with Me ionic liquid were regenerated with Acetonitrile and the structure of regenerated cellulose showed distinct difference depending on the electron beam treatment. Those results provide the electron beam pre-treatment could be applied as an energy efficient and environmentally benign method to increase the dissolution of cotton pulp with ionic liquids

Synthesis and properties of regenerated cellulose-based hydrogels with high strength and transparency for potential use as an ocular bandage

International Nuclear Information System (INIS)

Patchan, M.; Graham, J.L.; Xia, Z.; Maranchi, J.P.; McCally, R.; Schein, O.; Elisseeff, J.H.; Trexler, M.M.

2013-01-01

Cellulose is a biologically derived material with excellent wound-healing properties. The high strength of cellulose fibers and the ability to synthesize gels with high optical transparency make these materials suitable for ocular applications. In this study, cellulose materials derived from wood pulp, cotton, and bacterial sources were dissolved in lithium chloride/N,N-dimethylacetamide to form regenerated cellulose hydrogels. Material properties of the resulting hydrogels, including water content, optical transparency, and tensile and tear strengths, were evaluated. Synthesis parameters, including activation time, dissolution time, relative humidity, and cellulose concentration, were found to impact the material properties of the resulting hydrogels. Overnight activation time improves the optical transparency of the hydrogels from 77% to 97% at 550 nm, whereas controlling cellulose concentration improves their tear strength by as much as 200%. On the basis of the measured transmittance and strength values of the regenerated hydrogels prepared via the optimized synthesis parameters, Avicel PH 101, Sigma-Aldrich microcrystalline cellulose 435236, and bacterial cellulose types were prioritized for future biocompatibility testing and potential clinical investigation. - Highlights: • Hydrogels were prepared (via LiCl/DMAc) from 7 different types of cellulose. • Synthesis parameters (activation, gelation, and concentration) were optimized. • Impact of synthesis parameters on transparency and strength was explored

Synthesis and properties of regenerated cellulose-based hydrogels with high strength and transparency for potential use as an ocular bandage

Energy Technology Data Exchange (ETDEWEB)

Patchan, M. [Research and Exploratory Development Department, The Johns Hopkins University Applied Physics Laboratory, 11100 Johns Hopkins Road, Laurel, MD 20723 (United States); Graham, J.L. [Department of Biomedical Engineering, Johns Hopkins University, School of Medicine, 720 Rutland Avenue/Ross 720, Baltimore, MD 21205 (United States); Xia, Z.; Maranchi, J.P. [Research and Exploratory Development Department, The Johns Hopkins University Applied Physics Laboratory, 11100 Johns Hopkins Road, Laurel, MD 20723 (United States); McCally, R. [Research and Exploratory Development Department, The Johns Hopkins University Applied Physics Laboratory, 11100 Johns Hopkins Road, Laurel, MD 20723 (United States); Wilmer Eye Institute, Johns Hopkins Medical Institutions, 600 N. Wolfe Street, Baltimore, MD 21287 (United States); Schein, O. [Wilmer Eye Institute, Johns Hopkins Medical Institutions, 600 N. Wolfe Street, Baltimore, MD 21287 (United States); Elisseeff, J.H. [Department of Biomedical Engineering, Johns Hopkins University, School of Medicine, 720 Rutland Avenue/Ross 720, Baltimore, MD 21205 (United States); Trexler, M.M., E-mail: morgana.trexler@jhuapl.edu [Research and Exploratory Development Department, The Johns Hopkins University Applied Physics Laboratory, 11100 Johns Hopkins Road, Laurel, MD 20723 (United States)

2013-07-01

Cellulose is a biologically derived material with excellent wound-healing properties. The high strength of cellulose fibers and the ability to synthesize gels with high optical transparency make these materials suitable for ocular applications. In this study, cellulose materials derived from wood pulp, cotton, and bacterial sources were dissolved in lithium chloride/N,N-dimethylacetamide to form regenerated cellulose hydrogels. Material properties of the resulting hydrogels, including water content, optical transparency, and tensile and tear strengths, were evaluated. Synthesis parameters, including activation time, dissolution time, relative humidity, and cellulose concentration, were found to impact the material properties of the resulting hydrogels. Overnight activation time improves the optical transparency of the hydrogels from 77% to 97% at 550 nm, whereas controlling cellulose concentration improves their tear strength by as much as 200%. On the basis of the measured transmittance and strength values of the regenerated hydrogels prepared via the optimized synthesis parameters, Avicel PH 101, Sigma-Aldrich microcrystalline cellulose 435236, and bacterial cellulose types were prioritized for future biocompatibility testing and potential clinical investigation. - Highlights: • Hydrogels were prepared (via LiCl/DMAc) from 7 different types of cellulose. • Synthesis parameters (activation, gelation, and concentration) were optimized. • Impact of synthesis parameters on transparency and strength was explored.

Method and apparatus for assaying wood pulp fibers

Science.gov (United States)

Gustafson, Richard [Bellevue, WA; Callis, James B [Seattle, WA; Mathews, Jeffrey D [Neenah, WI; Robinson, John [Issaquah, WA; Bruckner, Carsten A [San Mateo, CA; Suvamakich, Kuntinee [Seattle, WA

2009-05-26

Paper pulp is added to a stain solution. The stain solution and pulp fibers are mixed to form a slurry. Samples are removed from the slurry and are admixed with dilution water and a bleach. Then, the fibers are moved into a flow cell where they are subjected to a light source adapted to stimulate fluorescence from the stained pulp fiber. Before the fiber slurry enters the flow cell it is mixed with a dilution water of bleach to reduce background fluorescence. The fluorescent light is collimated and directed through a dichroic filter onto a fluorescence splitting dichroic filter.

REPLACEMENT OF SOFTWOOD KRAFT PULP WITH ECF-BLEACHED BAMBOO KRAFT PULP IN FINE PAPER

Directory of Open Access Journals (Sweden)

Guanglei Zhao

2010-06-01

Full Text Available Non-wood fibers such as bamboo and wheat straw have been playing important roles in the pulp and paper industry in China. In this study an ECF-bleached bamboo kraft pulp was compared with a bleached softwood kraft pulp (NBSK as the reinforcement pulp in fine paper production. Areas that were examined include the refining of pure fibers, influence of bamboo on dewatering, retention, and sizing. The influence of bamboo kraft pulp as a part of a furnish replacing NBSK was compared as well. Results show that fiber shortening was more prominent with bamboo when refined. This resulted in a higher amount of fines, and addition wet-end chemicals may be required to compensate. Handsheets with bamboo as a reinforcement fiber showed similar mechanical and optical properties to handsheets containing NBSK.

Sono-chemical synthesis of cellulose nanocrystals from wood sawdust using Acid hydrolysis.

Science.gov (United States)

Shaheen, Th I; Emam, Hossam E

2018-02-01

Cellulose nanocrystal (CNC) is a unique material obtained from naturally occurring cellulose fibers. Owing to their mechanical, optical, chemical, and rheological properties, CNC gained significant interest. Herein, we investigate the potential of commercially non-recyclable wood waste, in particular, sawdust as a new resource for CNC. Isolation of CNC from sawdust was conducted as per acid hydrolysis which induced by ultrasonication technique. Thus, sawdust after being alkali delignified prior sodium chlorite bleaching, was subjected to sulfuric acid with concentration of 65% (w/w) at 60 ° C for 60min. After complete reaction, CNC were collected by centrifugation followed by dialyzing against water and finally dried via using lyophilization technique. The CNC yield attained values of 15% from purified sawdust. Acid hydrolysis mechanism exactly referred that, the amorphous regions along with thinner as well as shorter crystallites spreaded throughout the cellulose structure are digested by the acid leaving CNC suspension. The latter was freeze-dried to produce CNC powder. A thorough investigation pertaining to nanostructural characteristics of CNC was performed. These characteristics were monitored using TEM, SEM, AFM, XRD and FTIR spectra for following the changes in functionality. Based on the results obtained, the combination of sonication and chemical treatment was great effective in extraction of CNC with the average dimensions (diameter×length) of 35.2±7.4nm×238.7±81.2nm as confirmed from TEM. Whilst, the XRD study confirmed the crystal structure of CNC is obeyed cellulose type I with crystallinity index ∼90%. Cellulose nanocrystals are nominated as the best candidate within the range studied in the area of reinforcement by virtue of their salient textural features. Copyright © 2017 Elsevier B.V. All rights reserved.

Western Canadian wood residue production and consumption trends

International Nuclear Information System (INIS)

McCloy, B.

2006-01-01

This presentation considered various trends in western Canadian wood residue production and consumption. Potential markets for wood residue products were also discussed. Trends were reviewed by province for the years 2000-2004. British Columbia (BC) is currently the largest producer of residue in the country, and also retains the largest surpluses of bark, sawdust and shavings. Wood residues in BC are used in pulp and plywood mill production, as well as in the creation of particleboard and MDF. Surplus mill wood residue production in the province has greatly increased due to the Mountain Pine Beetle (MPB) infestation, which has in turn spurred expansion of the BC interior sawmill industry. The infestation has also resulted in a glut of pulp chips. Current wood residue products in Alberta are mostly used in pulp mill combined heat and power (CHP) systems, as well as for wood pellet production and the creation of particleboard and MDF. It was noted that surplus residues are rapidly declining in the province. Saskatchewan's wood residue storage piles are estimated to contain 2,900,000 BDt, while Manitoba surpluses are relatively minor. It was suggested that high natural gas prices have increased the payback on wood energy systems to approximately 2 years. The value of wood residue is now greater than $100/BDt as a substitute for natural gas once the wood energy system has been fully depreciated. Sawmills may now wish to consider equipping themselves to sell wood residue products, as most sawmills only require 20 per cent of their residues for heating purposes. It was concluded that markets for hog fuel wood pellets should be developed in Canada and internationally. Future markets may also develop if natural gas currently used in pulp mill power boilers and lime kilns is replaced with wood residue energy systems. refs., tabs., figs

Utilization of steam- and explosion-decompressed aspen wood by some anaerobes. [Acetivibrio cellulolyticus, Clostridium saccharolyticum, Zymomonas anaerobia

Energy Technology Data Exchange (ETDEWEB)

Khan, A W; Asther, M; Giuliano, C

1984-01-01

Tests made to study the suitability of using steam- and explosion-decompressed aspen wood as substrate in anaerobic fermentations indicated that after washing with dilute NaOH it becomes over 80% accessible to both mesophilic and thermophilic cellulolytic anaerobes and cellulases, compared with delignified, ball-milled pulp. After washing, this material was also found to be suitable for the single-step conversion of cellulose to ethanol using cocultures consisting of cellylolytic and ethanol-producing saccharolytic anaerobes; and without and after washing by the use of cellulolytic enzymes and ethanologenic anaerobes. 16 references, 3 tables.

Simultaneous production of α-cellulose and furfural from bagasse by steam explosion pretreatment

Directory of Open Access Journals (Sweden)

Vittaya Punsuvon

2008-02-01

Full Text Available Sugar cane bagasse was pretreated by steam explosion for the simultaneous production of furfural and α-cellulose pulp. The components of bagasse were fractionated after steam explosion. The details of the process are as follows. Bagasse was soaked in water for one night and steamed at temperatures varying between 206 and 223 C for 4 minutes. The steam exploded pulp was strained and washed with hot water to yield a liquor rich in hemicellulose-derived mono- and oligosaccharides. The remaining pulp was delignified by alkali for 120 minutes at 170C using, separately, NaOH load of 15, 20 and 25% of weight of the pulp. The delignified pulp was further bleached twice with 4% H2O2 charge of weight of the pulp to produce high α-cellulose pulp. The water liquor was evaporated and further hydrolysed and dehydrated with diluted H2SO4 in a stainless steel reactor to produce furfural. The result shows that the optimal pretreatment of steam explosion for 4 min at 218C leads to the yield of α-cellulose pulp at 193-201 g∙kg-1 of the original bagasse, and that furfural can be produced from xylose present in the liquor with a maximum conversion factor of 0.16.

A Scandinavian chemical wood pulp mill. Part 1. Energy audit aiming at efficiency measures

Energy Technology Data Exchange (ETDEWEB)

Klugman, Sofia [Department of Technology and Building Environment, Gaevle University, SE-801 76 Gaevle (Sweden); Karlsson, Magnus; Moshfegh, Bahram [Department of Mechanical Engineering, Division of Energy Systems, Linkoeping University, SE-581 83 Linkoeping (Sweden)

2007-03-15

A Swedish wood-pulp mill is surveyed in terms of energy supply and use in order to determine the energy-saving potential. Conservation measures are of increasing interest to Swedish industry, as energy prices have continued to rise in recent years. The electricity price particularly increased after the deregulation of the Scandinavian electricity market in 1996. The deregulation expanded to all of the EU in July 2004, which may increase the Swedish electricity price further until it reaches the generally higher European price level. Furthermore, oil prices have increased and the emissions trading scheme for CO{sub 2} adds to the incentive to reduce oil consumption. The energy system at the surveyed pulp mill is described in terms of electricity and process heat production and use. The total energy-saving potential is estimated and some saving points are identified. The heat that today is wasted at the mill has been surveyed in order to find potential for heat integration or heat export. The result shows that the mill probably could become self-sufficient in electricity. Particularly important in that endeavour is updating old pumps. (author)

Pulp and paper production from Spruce wood with kraft and ...

African Journals Online (AJOL)

STORAGESEVER

2010-03-15

Mar 15, 2010 ... optical properties of resultant paper were included to determine the properties of these pulp samples. ... pulping compounds in the kraft method are Na2S and .... Scanning electron microscope (SEM) measurement of pulp.

NANOFIBRILLATED CELLULOSE (NFC AS A POTENTIAL REINFORCEMENT FOR HIGH PERFORMANCE CEMENT MORTAR COMPOSITES

Directory of Open Access Journals (Sweden)

Mònica Ardanuy,

2012-07-01

Full Text Available In this work, nanofibrillated cellulose (NFC has been evaluated as a potential reinforcement for cement mortar composites. Two types of vegetable fibres with different composition and properties (cellulose content and microfibrillar angle, sisal, and cotton linters pulps, were initially characterised in order to assess their reinforcing capability. Sisal pulp was found to be most suitable as reinforcement for the brittle cementitious matrix. Nanofibrillated cellulose was produced by the application of a high intensity refining process of the sisal pulp. It was found that 6 hours of refining time was required to obtain the desired nanofibrillation of the fibers. Cement mortar composites reinforced with both the sisal fibres and the nanofibrillated cellulose were prepared, and the mechanical properties were determined under flexural tests. The cement mortar composites reinforced with the nanofibrillated cellulose exhibited enhanced flexural properties, but lower values of fracture energy, than the ones reinforced with the conventional sisal fibres.

Continental-Scale Patterns in Modern Wood Cellulose δ18O: Implications for Interpreting Paleo-Wood δ18O

Science.gov (United States)

Richter, S. L.; Johnson, A. H.; Dranoff, M. M.; Taylor, K. D.

2006-05-01

Ancient wood from Siberia and Arctic Canada is readily available and spans > 40 my of changing climate. Its isotopic composition might provide useful climate information, but there are several uncertainties that must be considered when interpreting the analyzed values of this potential resource. Aside from possible problems associated with diagenetic changes, oxygen isotopes in wood cellulose (δ18Ocel) are not likely to be good paleothermometers for the distant past when global patterns of precipitation δ18O (δ18Oppt) and temperatures were different, nor might they be good predictors of δ18Oppt because paleo-relative humidity, a contributor to δ18Ocel, is difficult to quantify. We sampled naturally growing, predominantly native trees in forested regions of North American and the Caribbean to determine how applicable the established relationships among δ18Ocel, temperature, relative humidity and δ18Oppt were at the continental scale, and how much relative humidity modifies the δ18Oppt signal. Different species at the same site may or may not have access to groundwater; they may have different phenological and physiological constraints that could cause them to have different δ18Ocel. Accordingly, we assessed species composition and depth to water table as potential sources of variability in δ18Ocel. We found up to 4‰ differences among species growing at the same site with conifer cellulose more enriched than angiosperm cellulose by 1.5‰ (P<.00001). Differences in landscape position, reflecting differing access to the water table, produced small (1‰) differences in δ18Ocel. While δ18Ocel was correlated with MAT (R2=.83-.91, P<.001), average summer minimum relative humidity (RH) combined with δ18Oppt explained most of the variability (R=.96) in δ18Ocel across North American and Caribbean forests. The isotopic enrichment that occurs during the processes leading to the incorporation of precipitation oxygen in cellulose is not constant, but varies from

Optical and Physical Properties of ONP Deinked Pulp

Directory of Open Access Journals (Sweden)

Iman Akbarpoor

2012-01-01

Full Text Available Enzymes are protein molecules with complex structures that accelerate the biochemical reactions. Activity of these chemical compounds is accomplished at limited range of pH, temperature and concentration. In this study, the effects of different concentrations of cellulose enzyme were investigated on deinking of old newsprint. Old newsprint (ONP was repulped at 5% consistency for 10 minutes in disintegrator with total revolution number of 26500. Enzymatic treatments of recycled ONP pulp were done under constant conditions (10% consistency,treatment time of 15 minutes, pH range of 5-5.5 at different cellulose concentrations of 0.025, 0.05, 0.1 and 0.2% (based on oven-dry waste paper. The optical and physical properties of the standard paper (60g/m2 made at different concentrations of cellulose were evaluated in comparison with control pulp (untreated ONP pulp with cellulase. Overall, the results achieved by comparison the optical properties of the paper produced indicated that using cellulase in deinking of ONP led to increase the brightness and the yellowness and decrease the opacity. The brightness was improved to a maximum level of 47.5 ISO %, but the yellowness was decreased to a minimum level of 11.3 ISO %, while the brightness reduced and the yellowness increased at higher concentrations than 0.05% cellulase. The highest opacity of 99.3 ISO % was achieved using 0.1% cellulase even higher than control pulp. The results gained by comparison the physical properties of the paper showed that using cellulase resulted in decrease of paper calliper, air resistance and density and improve the freeness of pulp

Formation of Irreversible H-bonds in Cellulose Materials

Science.gov (United States)

Umesh P. Agarwal; Sally A. Ralph; Rick S. Reiner; Nicole M. Stark

2015-01-01

Understanding of formation of irreversible Hbonds in cellulose is important in a number of fields. For example, fields as diverse as pulp and paper and enzymatic saccharification of cellulose are affected. In the present investigation, the phenomenon of formation of irreversible H-bonds is studied in a variety of celluloses and under two different drying conditions....

Effect of environmental conditions on the mechanical properties and fungal degradation of polycaprolactone/microcrystalline cellulose/wood flour composites

Science.gov (United States)

Ronald Sabo; Liwei Jin; Nicole Stark; Rebecca E. Ibach

2013-01-01

Polycaprolactone (PCL) filled with microcrystalline cellulose (MCC), wood flour (WF), or both were characterized before and after exposure to various environmental conditions for 60 days. PCL/WF composites had the greatest tensile strength and modulus compared to neat PCL or PCL composites containing MCC. Electron microscopy indicated better adhesion between WF...

The effect of acid hydrolysis pretreatment on crystallinity and solubility of kenaf cellulose membrane

Energy Technology Data Exchange (ETDEWEB)

Saidi, Anis Syuhada Mohd; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Padzil, Farah Nadia Mohammad [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor (Malaysia)

2015-09-25

Cellulose was extracted from kenaf core pulp (KCP) by series of bleaching steps in the sequence (DEED) where D and E are referred as acid and alkali treatment. The bleached kenaf pulp (BKCP) is then pretreated with acid hydrolysis at room temperature for 1 and 3 h respectively. The pretreated cellulose is dissolved in lithium hydroxide/urea (LiOH/urea) and cellulose solution produced was immersed in distilled water bath. BKCP without treatment was also conducted for comparison purpose. The effects of acid hydrolysis pretreatment on solubility and crystallinity are investigated. Higher solubility of cellulose solution is achieved for treated samples. Cellulose II formation and crystallinity index of the cellulose membrane were determined by X-ray diffraction (XRD)

The effect of acid hydrolysis pretreatment on crystallinity and solubility of kenaf cellulose membrane

International Nuclear Information System (INIS)

Saidi, Anis Syuhada Mohd; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Padzil, Farah Nadia Mohammad

2015-01-01

Cellulose was extracted from kenaf core pulp (KCP) by series of bleaching steps in the sequence (DEED) where D and E are referred as acid and alkali treatment. The bleached kenaf pulp (BKCP) is then pretreated with acid hydrolysis at room temperature for 1 and 3 h respectively. The pretreated cellulose is dissolved in lithium hydroxide/urea (LiOH/urea) and cellulose solution produced was immersed in distilled water bath. BKCP without treatment was also conducted for comparison purpose. The effects of acid hydrolysis pretreatment on solubility and crystallinity are investigated. Higher solubility of cellulose solution is achieved for treated samples. Cellulose II formation and crystallinity index of the cellulose membrane were determined by X-ray diffraction (XRD)

Wood anatomical and chemical properties related to the pulpability ...

African Journals Online (AJOL)

Eucalyptus globulus is one of the most important hardwood species used by the pulp and paper industry due to its high pulp yield, high wood density, excellent fibre quality and good handsheet properties. However, the wood is a highly variable and complex material that has different chemical, physical and anatomical ...

The economic potential of wood pellet production from alternative, low-value wood sources in the southeast of the US

NARCIS (Netherlands)

Hoefnagels, Ric; Junginger, Martin; Faaij, Andre

2014-01-01

The global demand for wood pellets used for energy purposes is growing. Therefore, increased amounts of wood pellets are produced from primary forestry products, such as pulp wood. The present analysis demonstrates that substantial amounts of alternative, low-value wood resources are available that

Optimizing Extraction of Cellulose and Synthesizing Pharmaceutical Grade Carboxymethyl Sago Cellulose from Malaysian Sago Pulp

Directory of Open Access Journals (Sweden)

Anand Kumar Veeramachineni

2016-06-01

Full Text Available Sago biomass is an agro-industrial waste produced in large quantities, mainly in the Asia-Pacific region and in particular South-East Asia. This work focuses on using sago biomass to obtain cellulose as the raw material, through chemical processing using acid hydrolysis, alkaline extraction, chlorination and bleaching, finally converting the material to pharmaceutical grade carboxymethyl sago cellulose (CMSC by carboxymethylation. The cellulose was evaluated using Thermogravimetric Analysis (TGA, Infrared Spectroscopy (FTIR, X-Ray Diffraction (XRD, Differential Scanning Calorimetry (DSC and Field Emission Scanning Electronic Microscopy (FESEM. The extracted cellulose was analyzed for cellulose composition, and subsequently modified to CMSC with a degree of substitution (DS 0.6 by typical carboxymethylation reactions. X-ray diffraction analysis indicated that the crystallinity of the sago cellulose was reduced after carboxymethylation. FTIR and NMR studies indicate that the hydroxyl groups of the cellulose fibers were etherified through carboxymethylation to produce CMSC. Further characterization of the cellulose and CMSC were performed using FESEM and DSC. The purity of CMSC was analyzed according to the American Society for Testing and Materials (ASTM International standards. In this case, acid and alkaline treatments coupled with high-pressure defibrillation were found to be effective in depolymerization and defibrillation of the cellulose fibers. The synthesized CMSC also shows no toxicity in the cell line studies and could be exploited as a pharmaceutical excipient.

Dual morphology (fibres and particles) cellulosic filler for WPC materials

Energy Technology Data Exchange (ETDEWEB)

Valente, Marco, E-mail: marco.valente@uniroma1.it; Tirillò, Jacopo; Quitadamo, Alessia, E-mail: alessia.quitadamo@uniroma1.it [University of Rome La Sapienza Dep. of Chemical and Material Engineering (Italy); Santulli, Carlo [University of Camerino, School of Architecture and Design (Italy)

2016-05-18

Wood-plastic composites (WPC) were fabricated by using a polyethylene (PE) matrix and filling it with wood flour in the amount of 30 wt.%, and compared with the same composites with further amount of 10 wt.% of cellulosic recycled fibres added. The materials were produced by turbomixing and subsequent moulding under pressure. Mechanical properties of both WPC and WPC with cellulosic recycled fibres were evaluated through mechanical and physical-chemical tests. Tensile tests clarified that a moderate reduction is strength is observed with the bare introduction of wood flour with respect to the neat PE matrix, whilst some recovery is offered by the addition of recycled cellulose fibres. Even more promisingly, the elastic modulus of PE matrix is substantially improved by the addition of wood flour (around 8% on average) and much more so with the further addition of recycled cellulose (around 20% on average). The fracture surfaces from the tensile test were analysed by scanning electron microscope (SEM) indicating a reduction in microporosity as an effect of added cellulose. The water absorption test and the hardness measure (Shore D) were also performed. SEM analysis underlined the weak interface between both wood particle and cellulosic recycled fibres and matrix. The water absorption test showed a higher mass variation for pure WPC than WPC with cellulosic recycled fibres. The hardness measurement showed that the presence of cellulosic recycled fibres improves both superficial hardness of the composite and temperature resistance.

Dual morphology (fibres and particles) cellulosic filler for WPC materials

International Nuclear Information System (INIS)

Valente, Marco; Tirillò, Jacopo; Quitadamo, Alessia; Santulli, Carlo

2016-01-01

Wood-plastic composites (WPC) were fabricated by using a polyethylene (PE) matrix and filling it with wood flour in the amount of 30 wt.%, and compared with the same composites with further amount of 10 wt.% of cellulosic recycled fibres added. The materials were produced by turbomixing and subsequent moulding under pressure. Mechanical properties of both WPC and WPC with cellulosic recycled fibres were evaluated through mechanical and physical-chemical tests. Tensile tests clarified that a moderate reduction is strength is observed with the bare introduction of wood flour with respect to the neat PE matrix, whilst some recovery is offered by the addition of recycled cellulose fibres. Even more promisingly, the elastic modulus of PE matrix is substantially improved by the addition of wood flour (around 8% on average) and much more so with the further addition of recycled cellulose (around 20% on average). The fracture surfaces from the tensile test were analysed by scanning electron microscope (SEM) indicating a reduction in microporosity as an effect of added cellulose. The water absorption test and the hardness measure (Shore D) were also performed. SEM analysis underlined the weak interface between both wood particle and cellulosic recycled fibres and matrix. The water absorption test showed a higher mass variation for pure WPC than WPC with cellulosic recycled fibres. The hardness measurement showed that the presence of cellulosic recycled fibres improves both superficial hardness of the composite and temperature resistance.

Influência dos atributos do solo sobre a qualidade da madeira de Pinus taeda para produção de celulose Kraft Influence of soil attributes on quality of Pinus taeda wood for cellulose Kraft production

Directory of Open Access Journals (Sweden)

Patrícia Aparecida Rigatto

2004-04-01

characteristics, as well as their relation to cellulose production. Eight sites with twelve-year-old trees were selected based on soil type, soil texture and primary vegetation. The soil variables studied were bulk density, total porosity, macroporosity, water availability, fertility and grain size distribution. For tree selection, dendrometric measurements of 50 trees were taken per site, and 5 average size trees selected per site. Total and commercial height and DBH were measured and discs removed. Tree samples were analyzed for basic density, chemical composition, tracheid morphological characteristics, nutritional status and Kraft cellulose production. The soil chemical attributes exerted significant influence on wood quality, but the soil physical attributes showed greater influence on cellulose productivity. Sites with higher growth rate and those with clay texture showed lower values of basic density, higher content of extract and lignin, thus showing lower content of holocellulose and cellulose, shorter and wider tracheids with thinner walls and higher lumen diameters, and lower cellulose yield. Based on these results, it was concluded that cellulose pulp characteristics can be estimated by analyzing wood characteristics combined with the existing site edaphic conditions.

Technical Report Cellulosic Based Black Liquor Gasification and Fuels Plant Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Fornetti, Micheal [Escanaba Paper Company, MI (United States); Freeman, Douglas [Escanaba Paper Company, MI (United States)

2012-10-31

produce transportation fuels and produce pulp at the same time. This has the added advantage of reducing or eliminating the need for a recovery boiler. The recovery boiler is an extremely expensive unit operation in the Kraft process and is key to the chemical recovery system that makes the Kraft process successful. Going to a gasification process with potentially higher energy efficiency, improve the pulping process and be more efficient with the use of wood. At the same time a renewable fuel product can be made. Cellulosic Based Black Liquor Gasification and Fuels Plant progressed with the design of the mill as Chemrec continued to work on their pilot plant data gathering. The design information helped to guide the pilot plant and vice versa. In the end, the design details showed that the process was technically feasible. However, at the relatively small size of this plant the specific capital cost was very high and could only be considered if the pulp operation needed to replace the recovery boiler. Some of the reasons for the costs being high are attributed to the many constraints that needed to be addressed in the pulping process. Additionally, the Methanol product did not have a vehicle fuel supply chain to enter into. A different product selection could have eliminated this issue. However, with the selected design, the installation at Escanaba Paper Mill was not economically feasible and the project was not pursued further.

Wood composites

Science.gov (United States)

Lars Berglund; Roger M. Rowell

2005-01-01

A composite can be defined as two or more elements held together by a matrix. By this definition, what we call “solid wood” is a composite. Solid wood is a three-dimensional composite composed of cellulose, hemicelluloses and lignin (with smaller amounts of inorganics and extractives), held together by a lignin matrix. The advantages of developing wood composites are (...

Isolation and Rheological Characterization of Cellulose Nanofibrils (CNFs from Coir Fibers in Comparison to Wood and Cotton

Directory of Open Access Journals (Sweden)

Daran Yue

2018-03-01

Full Text Available In this report, the isolation and rheological characterization of cellulose nanofibrils from coir (CNFs-1 were studied and compared with the CNFs from wood (CNFs-2 and cotton (CNFs-3. Cellulose nanofibrils were isolated successfully from coir fibers by chemical treatments followed by ultrasonic fibrillation. During ultrasonic processing, the size and the crystal structure of the CNFs were influenced by the raw materials. In comparison to CNFs-2 and CNFs-3, CNFs-1 from coir fibers presented diverse advantages, such as sufficient fibrillation with a low diameter distribution, in the range of 2–4 nm and high crystallinity. In the dynamic rheology study of CNFs-1, elastic behavior was observed and maintained due to the formation of gel-like steady network structures, which could not be easily deconstructured by frequency shearing and temperature changing. All results indicated that coir fibers could be used as a valuable resource for the preparation of CNFs, which exhibited comparable properties with those isolated from wood, in regard to morphology and rheological properties. This work provides a basis for further advanced applications using the CNFs isolated from coir fibers.

Methods to use biomass, consisting of peat and wood material, to extract fiber substance to be used to make paper pulp and a fuel product. Saett att ur biomassa, bestaaende av torv och vedmatarial, utvinna en foer tillverkning av en pappersmassaprodukt laemplig fibermassa samt en braensleprodukt

Energy Technology Data Exchange (ETDEWEB)

Lindahl, J A.I.

1985-12-16

Peat cut from the upper layers is used to make paper pulp of low density. The wood material of the peat is mechanically separated three times. The result is a pulp of peat fibres and wood fibres and dewatered colloidal peat to be used as a fuel. (M.B).

Reactivity of syringyl and guaiacyl lignin units and delignification kinetics in the kraft pulping of Eucalyptus globulus wood using Py-GC-MS/FID.

Science.gov (United States)

Lourenço, Ana; Gominho, Jorge; Marques, António Velez; Pereira, Helena

2012-11-01

Eucalyptus globulus sapwood and heartwood showed no differences in lignin content (23.0% vs. 23.7%) and composition: syringyl-lignin (17.9% vs. 18.0%) and guaiacyl-lignin (4.8% vs. 5.2%). Delignification kinetics of S- and G-units in heartwood and sapwood was investigated by Py-GC-MS/FID at 130, 150 and 170°C and modeled as double first-order reactions. Reactivity differences between S and G-units were small during the main pulping phase and the higher reactivity of S over G units was better expressed in the later pulping stage. The residual lignin composition in pulps was different from wood or from samples in the initial delignification stages, with more G and H-units. S/G ratio ranged from 3 to 4.5 when pulp residual lignin was higher than 10%, decreasing rapidly to less than 1. The S/H was initially around 20 (until 15% residual lignin), decreasing to 4 when residual lignin was about 3%. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of Cellulases and Xylanases on Refining Process and Kraft Pulp Properties.

Directory of Open Access Journals (Sweden)

Kamila Przybysz Buzała

Full Text Available Samples of bleached kraft pine cellulosic pulp, either treated with an enzyme preparation (a Thermomyces lanuginosus xylanase, an Aspergillus sp. cellulase, and a multienzyme preparation NS-22086 containing both these activities or untreated, were refined in a laboratory PFI mill. The treatment with cellulases contained in the last two preparations significantly improved the pulp's susceptibility to refining (the target freeness value of 30°SR was achieved in a significantly shorter time, increased water retention value (WRV and fines contents while the weighted average fiber length was significantly reduced. These changes of pulp parameters caused deterioration of paper strength properties. The treatment with the xylanase, which partially hydrolyzed xylan, small amounts of which are associated with cellulose fibers, only slightly loosened the structure of fibers. These subtle changes positively affected the susceptibility of the pulp to refining (refining energy was significantly reduced and improved the static strength properties of paper. Thus, the treatment of kraft pulps with xylanases may lead to substantial savings of refining energy without negative effects on paper characteristics.

Obtención de lignina y celulosa de residuos de maíz (ING)

OpenAIRE

Manuel Moya P; Marlen Durán Ch.; María Sibaja B.

2016-01-01

Using a simple pulping method, lignin and cellulose were obtained from corn waste in good yield. Thermal analysis results showed that lignins were thermally less stable than Kraft Lignin from soft woods. Using several different methods, it was found that the celluloses were less cristallin than Avicel cellulose.

Waste fatty acid addition to black liquor to decrease tall oil soap solubility and increase skimming efficiency in kraft mills pulping mountain pine beetle-infested wood

Energy Technology Data Exchange (ETDEWEB)

Uloth, V.; Guy, E. [FPInnovations, Prince George, BC (Canada). PAPRICAN Div.; Shewchuk, D. [Cariboo Pulp and Paper, Quesnel, BC (Canada); Van Heek, R. [Aker Kvaerner, Vancouver, BC (Canada)

2009-07-01

This paper presented the results of tests conducted to determine if the addition of waste fatty acids from vegetable oil processing might decrease tall oil soap solubility in pine-beetle impacted wood from British Columbia (BC). The soap recovery and tall oil production at BC mills has fallen by 30 to 40 percent in recent years due to the pulping of high proportions of grey-stage beetle-impacted wood. Full-scale mill tests were conducted over a 4-day period. The study showed that the addition of tall oil fatty acids or waste fatty acids from vegetable oil processing could decrease tall oil soap solubility and increase the soup skimming efficiency in mills pulping a large percentage of grey stage beetle-infested wood. The addition of fatty acids increased tall oil soap skimming efficiency from 50.2 percent in the baseline tests to 71.8 percent based on the total soap available, and from 76.7 percent in the baseline tests to 87.5 percent based on insoluble soap only. The economic analyses indicated that waste fatty acid addition could be economical when natural gas and oil prices are high. 4 tabs., 9 figs.

Atmospheric pressure cold plasma treatment of cellulose based fillers for wood plastic composites

Science.gov (United States)

Lekobou, William; Englund, Karl; Pedrow, Patrick; Scudiero, Louis

2011-10-01

The main challenge of wood plastic composites (WPC) resides in the low interfacial adhesion due to incompatibility between the cellulose based filler that has a polar surface and most common matrixes, polyolefins which are non-polar. Plasma treatment is a promising technique for surface modification and its implementation into the processing of WPC would provide this industry with a versatile and nearly environmentally benign manufacturing tool. Our investigation aims at designing a cold atmospheric pressure plasma reactor for coating fillers with a hydrophobic material prior to compounding with the matrix. Deposition was achieved with our reactor that includes an array of high voltage needles, a grounded metal mesh, Ar as carrier gas and C2H2 as the precursor molecule. Parameters studied have included gas feed rates and applied voltage; FTIR, ESCA, AFM and SEM imaging were used for film diagnostics. We will also report on deposition rate and its dependence on radial and axial position as well as the effects of plasma-polymerized acetylene on the surface free energy of cellulose based substrates.

Production of cellulose nanoparticles from blue agave waste treated with environmentally friendly processes.

Science.gov (United States)

Robles, Eduardo; Fernández-Rodríguez, Javier; Barbosa, Ananda M; Gordobil, Oihana; Carreño, Neftali L V; Labidi, Jalel

2018-03-01

Tequila elaboration leaves two main byproducts that are undervalued (bagasse and leaves). Organosolv pulping and Total Chlorine Free bleaching were integrated to obtain cellulose fibers from agricultural waste which consisted of blue agave bagasse and leaf fibers; together they represent a green process which valorizes biomass waste. The obtained celluloses were characterized by FT-IR, colorimetry, and SEM and their extraction yields were evaluated. These celluloses were used to produce cellulose nanocrystals and cellulose nanofibers. First, an acid hydrolysis was performed in a sonication bath to induce cavitation during the reaction to produce cellulose nanocrystals. Then a high-pressure homogenization was selected to produce cellulose nanofibers. These nanocelluloses were characterized by powder XRD, Nanosizer, zeta potential, NMR, and electronic microscopy. Results showed that cellulose from organosolv pulps bleached with TCF bleaching is suitable for nanocellulose production. Moreover, the use of a new step to separate cellulose nanocrystals resulted in yields almost doubling traditional yields, while the rest of the properties remained within the expected. Copyright © 2018 Elsevier Ltd. All rights reserved.

Obtención de lignina y celulosa de residuos de maíz (ING

Directory of Open Access Journals (Sweden)

Manuel Moya P

2016-03-01

Full Text Available Using a simple pulping method, lignin and cellulose were obtained from corn waste in good yield. Thermal analysis results showed that lignins were thermally less stable than Kraft Lignin from soft woods. Using several different methods, it was found that the celluloses were less cristallin than Avicel cellulose.

The influence of lignin on steam pretreatment and mechanical pulping of poplar to achieve high sugar recovery and ease of enzymatic hydrolysis.

Science.gov (United States)

Chandra, Richard P; Chu, QiuLu; Hu, Jinguang; Zhong, Na; Lin, Mandy; Lee, Jin-Suk; Saddler, Jack

2016-01-01

With the goal of enhancing overall carbohydrate recovery and reducing enzyme loading refiner mechanical pulping and steam pretreatment (210°C, 5 min) were used to pretreat poplar wood chips. Neutral sulphonation post-treatment indicated that, although the lignin present in the steam pretreated substrate was less reactive, the cellulose-rich, water insoluble component was more accessible to cellulases and Simons stain. This was likely due to lignin relocation as the relative surface lignin measured by X-ray photoelectron spectroscopy increased from 0.4 to 0.8. The integration of sulphite directly into steam pretreatment resulted in the solubilisation of 60% of the lignin while more than 80% of the carbohydrate present in the original substrate was recovered in the water insoluble fraction after Na2CO3 addition. More than 80% of the sugars present in the original cellulose and xylan could be recovered after 48 h using an enzyme loading of 20 mg protein/g cellulose at a 10% substrate concentration. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparative pulping of sunflower stalks

Directory of Open Access Journals (Sweden)

Valerii Barbash

2016-03-01

Full Text Available The procedure of holocellulose content determination in non-wood plant raw materials was developed. The strength properties of pulp obtained from sunflower stalks by neutral-sulphite, soda, alkaline sulphite-anthraquinone-ethanol and peracetic methods of delignification were studied. Methodology of comparison of plant materials delignification methods using new lignin-carbohydrate diagram was proposed. It was shown, that the alkaline sulphite-anthraquinone-ethanol method of pulping is characterized by the highest delignification degree and is the most efficient among the studied methods

A novel green approach for the preparation of cellulose nanowhiskers from white coir.

Science.gov (United States)

Nascimento, Diego M; Almeida, Jessica S; Dias, Amanda F; Figueirêdo, Maria Clea B; Morais, João Paulo S; Feitosa, Judith P A; de F Rosa, Morsyleide

2014-09-22

The aim of this work was to optimize the extraction of cellulose nanowhiskers (CNW) from unripe coconut husk fibers (CHF). The CHF was delignified using organosolv process, followed by alkaline bleaching (5% (w/w) H2O2+4% (w/w) NaOH; 50°C, 90 min). The CHF was subsequently hydrolyzed with 30% (v/v) sulfuric acid (60°C, 360 min). The process yielded a partially delignified acetosolv cellulose pulp and acetic black liquor, from which the lignin was recovered. The CNW from the acetosolv pulp exhibited an average length of 172±88 nm and a diameter of 8±3 nm, (aspect ratio of 22±8). The surface charge of the CNW was -33 mV, indicating a stable aqueous colloidal suspension. The nanocrystals presented physical characteristics close to those extracted from cellulose pulp made by CHF chlorine-pulping. This approach offers the additional advantage of extracting the lignin as an alternative to eradication. Copyright © 2014 Elsevier Ltd. All rights reserved.

The extractives of Pinus pinaster wood

Science.gov (United States)

Richard W. Hemingway; W. E. Hillis; L. S. Lau

1973-01-01

The extractives in Pinus pinaster wood grown in South Australia were examined as part of an assessment of the suitability of this wood for manufacture of absorbent tissues from bisulphite pulps. The average petroleum solubility of the wood was 2.0% but the amount and composition of the petroleum extract varied widely depending upon the age of the...

Low Temperature Soda-Oxygen Pulping of Bagasse.

Science.gov (United States)

Yue, Fengxia; Chen, Ke-Li; Lu, Fachuang

2016-01-13

Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today's pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm³/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115-125 °C), this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

Low Temperature Soda-Oxygen Pulping of Bagasse

Directory of Open Access Journals (Sweden)

Fengxia Yue

2016-01-01

Full Text Available Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm3/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115–125 °C, this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

Residual wood polymers facilitate compounding of microfibrillated cellulose with poly(lactic acid) for 3D printer filaments

Science.gov (United States)

Winter, Armin; Mundigler, Norbert; Holzweber, Julian; Veigel, Stefan; Müller, Ulrich; Kovalcik, Adriana; Gindl-Altmutter, Wolfgang

2017-12-01

Microfibrillated cellulose (MFC) is a fascinating material with an obvious potential for composite reinforcement due to its excellent mechanics together with high specific surface area. However, in order to use this potential, commercially viable solutions to important technological challenges have to be found. Notably, the distinct hydrophilicity of MFC prevents efficient drying without loss in specific surface area, necessitating storage and processing in wet condition. This greatly hinders compounding with important technical polymers immiscible with water. Differently from cellulose, the chemistry of the major wood polymers lignin and hemicellulose is much more diverse in terms of functional groups. Specifically, the aromatic moieties present in lignin and acetyl groups in hemicellulose provide distinctly less polar surface-chemical functionality compared to hydroxyl groups which dominate the surface-chemical character of cellulose. It is shown that considerable advantages in the production of MFC-filled poly(lactic acid) filaments for three-dimensional printing can be obtained through the use of MFC containing residual lignin and hemicellulose due to their advantageous surface-chemical characteristics. Specifically, considerably reduced agglomerations of MFC in the filaments in combination with improved printability and improved toughness of printed objects are achieved. This article is part of a discussion meeting issue `New horizons for cellulose nanotechnology'.

Residual wood polymers facilitate compounding of microfibrillated cellulose with poly(lactic acid) for 3D printer filaments.

Science.gov (United States)

Winter, Armin; Mundigler, Norbert; Holzweber, Julian; Veigel, Stefan; Müller, Ulrich; Kovalcik, Adriana; Gindl-Altmutter, Wolfgang

2018-02-13

Microfibrillated cellulose (MFC) is a fascinating material with an obvious potential for composite reinforcement due to its excellent mechanics together with high specific surface area. However, in order to use this potential, commercially viable solutions to important technological challenges have to be found. Notably, the distinct hydrophilicity of MFC prevents efficient drying without loss in specific surface area, necessitating storage and processing in wet condition. This greatly hinders compounding with important technical polymers immiscible with water. Differently from cellulose, the chemistry of the major wood polymers lignin and hemicellulose is much more diverse in terms of functional groups. Specifically, the aromatic moieties present in lignin and acetyl groups in hemicellulose provide distinctly less polar surface-chemical functionality compared to hydroxyl groups which dominate the surface-chemical character of cellulose. It is shown that considerable advantages in the production of MFC-filled poly(lactic acid) filaments for three-dimensional printing can be obtained through the use of MFC containing residual lignin and hemicellulose due to their advantageous surface-chemical characteristics. Specifically, considerably reduced agglomerations of MFC in the filaments in combination with improved printability and improved toughness of printed objects are achieved.This article is part of a discussion meeting issue 'New horizons for cellulose nanotechnology'. © 2017 The Author(s).

The use of near-infrared scanning for the prediction of pulp yield and ...

African Journals Online (AJOL)

Calibration models to predict pulp yield, cellulose and lignin content were developed by applying chemometrics and partial least squares regression. Validation and determination of prediction accuracy of the models were performed using independent data. The prediction of cellulose and lignin were acceptable with ...

Research on Wheat Straw Pulping with Ionic Liquid 1-Ethyl-3-Methylimidazole Bromide

Directory of Open Access Journals (Sweden)

Wei Song

2016-12-01

Full Text Available In this paper, the pulping process of wheat straw using ionic liquid 1-ethyl-3-methylimidazolium bromide ([Emim]Br as the digestion liquor is presented. The influence of pulping conditions on the pulp yield are analysed by single-factor and orthogonal experiments, and optimum pulping conditions are obtained. The average pulp yield reaches 44 %, and the average recovery rate of ionic liquid is 93.5 %. The XRD pattern shows no obvious change in the crystal structure of the wheat straw cellulose. Additionally, the SEM image illustrates that there are many fine fibres in the pulp and the spaces between the fibres are large.

Integrated Procurement of Pulpwood and Energy Wood by Whole-Tree Bundling

Energy Technology Data Exchange (ETDEWEB)

Jylhae, Paula (Finnish Forest Research Inst., Kannus Unit, P.O. Box 44, FI-69101 Kannus (Finland)); Kaerhae, Kalle (Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland)); Laitila, Juha (Finnish Forest Research Inst., Joensuu Unit, P.O. Box 68, FI-80101 Joensuu (Finland))

2008-10-15

Total supply chain costs of pulpwood and energy wood harvested from early thinnings can be reduced by applying an integrated procurement system based on whole-tree bundling using a newly-developed whole-tree bundler. Pulpwood-dimensioned whole trees are incorporated into pulpwood bundles. The pulp and energy fraction are not separated before the wood reaches the debarking drum of the pulp mill. Based on industrial trials with Scots pine harvested from first thinnings, pulp made from blend of bundles and conventional pulpwood meets the quality requirements of chemical pine pulp. Small-diameter trees and undesirable tree species can be accumulated into separate energy wood bundles, which are transported to energy generation. Due to load compaction, cost savings are expected especially in forest haulage and road transportation. The system shows greatest potential when harvesting first-thinning stands with a breast-height diameter of 7-10 cm

Studies on the utilization of agricultural residues in the manufacture of pulp and paper, and industrial chemicals

Energy Technology Data Exchange (ETDEWEB)

Joshi, V.S.; Kamath, G.P.; Basu, S.

1980-03-15

While demand for pulp and paper products in India is increasing at the annual rate of 7 to 8%, availability of cellulosic raw material to meet the ever increasing demand is becoming a serious problem. It has been estimated that bamboo, the traditional source of cellulosic raw material in India, even after ensuring the most scientific and best possible exploitation, could provide less than 50% of the requirement. In a big agricultural country like India, agri-residues like straws and bagasse, along with jute sticks, available in huge quantity, could provide substantial amount of cellulosic resources to the pulp and paper industry. Realizing the importance of agri-residue utilization in Indian economy, a series of research projects have been initiated and completed during the last 15 years to study the techno-economic feasibility of manufacturing pulp, paper, and industrial chemicals, based on rice and wheat straws, bagasse, and jute sticks. The economic advantages of the mechano-chemical pulping process, as compared to the conventional pressure, pulping process, for the conversion of agri-residues into pulp and paer is evaluated. For highlighting the importance of agri-residues in the field of useful chemical recovery possibilities, experimental data are given on the saccarification of agri-residues into reducing sugars by the simple acid hydrolysis method with the help of concentrated sulfuric acid.

Butanol production from wood pulping hydrolysate in an integrated fermentation-gas stripping process.

Science.gov (United States)

Lu, Congcong; Dong, Jie; Yang, Shang-Tian

2013-09-01

Wood pulping hydrolysate (WPH) containing mainly xylose and glucose as a potential substrate for acetone-butanol-ethanol (ABE) fermentation was studied. Due to the inhibitors present in the hydrolysate, several dilution levels and detoxification treatments, including overliming, activated charcoal adsorption, and resin adsorption, were evaluated for their effectiveness in relieving the inhibition on fermentation. Detoxification using resin and evaporation was found to be the most effective method in reducing the toxicity of WPH. ABE production in batch fermentation by Clostridium beijerinckii increased 68%, from 6.73 g/L in the non-treated and non-diluted WPH to 11.35 g/L in the resin treated WPH. With gas stripping for in situ product removal, ABE production from WPH increased to 17.73 g/L, demonstrating that gas stripping was effective in alleviating butanol toxicity by selectively separating butanol from the fermentation broth, which greatly improved solvents production and sugar conversion in the fermentation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Kraft pulping and ECF bleaching of Eucalyptus globulus pretreated by the white-rot fungus Ceriporiopsis subvermispora - doi: 10.4025/actascitechnol.v34i3.12410

Directory of Open Access Journals (Sweden)

Claudio Salazar

2012-05-01

Full Text Available Eucalyptus globulus wood chips were decayed by the lignin-degrading fungus Ceriporiopsis subvermispora as a pretreatment step before kraft pulping. Weight and component losses of wood after the biotreatment were the following: weight (5%, glucans (1.5%, xylans (4.3%, lignin (5.7% and extractives (57.5%. The residual amount of lignin (expressed by the kappa number in pulps from biotreated wood chips was lower than that of pulps from the undecayed control. Depending on the delignification degree, kraft biopulps presented similar or up to 4% increase in pulp yield and 20% less hexenuronic acids (HexA than control pulps. The extended delignification with O2 decreases approximately 50% of the kappa number of the pulps and increases brightness, but had no effect in HexA reduction. The bleaching steps with chlorine dioxide (D0ED1 sequence decreased the kappa number up to 97%, increased pulp brightness up to 84% ISO and decreased HexA amount up to 91%. The use of C. subvermispora in biopulping of E. globulus generated important benefits during the production of kraft pulps that are reflected in a high pulp yield, low residual lignin content, low HexA amount, high brightness and viscosity of the biopulps as compared with pulps produced from untreated wood chips.

Acid-base synergistic flame retardant wood pulp paper with high thermal stability.

Science.gov (United States)

Wang, Ning; Liu, Yuansen; Xu, Changan; Liu, Yuan; Wang, Qi

2017-12-15

Acid-catalytic degradation caused by acid source flame retardants is the main reason for a decline in thermal stability of flame-retarded lignocellulosic materials. In the present research, a guanidine phosphate (GP)/borax (BX) flame retardant system based on acid-base synergistic interaction was designed and used in wood pulp paper (WPP) to solve this problem. Results showed that the treated WPP obtained good flame retardancy with a limiting oxygen index (LOI) value of 35.7%. As a basic flame retardant, borax could chemically combine with the acids released by guanidine phosphate, thus decreasing the acidity of the system in the initial heating stage. In this way, acid-catalytic degradation is greatly retarded on the lignocelluloses to improve thermal stability (the temperature of maximum degradation peak from 286°C to 314°C). Meanwhile, borax was also advantageous to form a denser and firmer condensed phase through reinforcement of the acid-base reaction product, borophosphates, allowing it to provide a protective barrier with higher quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of Partial Pre-Extraction of Hemicelluloses on the Properties of Pinus radiata Chemimechanical Pulps

Directory of Open Access Journals (Sweden)

Pablo Reyes

2015-09-01

Full Text Available Extraction of hemicelluloses prior to pulping and conversion of the extracted hemicelluloses to other bioproducts could provide additional revenue to traditional pulp and paper industries. The effect of hemicelluloses pre-extraction with a hydrothermal (HT process on Pinus radiata chemimechanical pulp (CMP properties was investigated in this study. The HT extraction resulted in a release of 7% to 58% of the initial amount of hemicelluloses from the wood. The extraction yield increased with temperature and extraction time. This hemicellulosic fraction was in the form of low molar mass oligomers with molecular weights varying from 1.5 to 100 kDa. Compared with the control (unextracted CMP pulp, the HT pre-extraction significantly reduced the refining energy to obtain a given fibrillation degree (freeness. The pulp yield with the HT/CMP process was in the range of 56% to 75%. Fiber properties of the pulps from pre-extracted wood, such as fiber length, were reduced, while increases in fiber width, fines content, fiber coarseness, and kink index were observed in comparison with the control pulps. The strength properties of CMP pulps decreased with increasing amounts of hemicellulose removal during the stage prior to pulping.

Using renewable sources in the pulp and paper mills

International Nuclear Information System (INIS)

Hazi, Aneta; Hazi, Gheorghe

2007-01-01

The pulp and paper industry is a major consumer of natural sources (wood) and energy (fossil fuels, electricity) and a significant contributor of pollutant discharges to the environment. In this paper there are presented pulp and paper making process and steam and power generation using renewable sources. This paper includes also an exergy analysis of the steam and power generation process for a pulp and paper mill. Based on the analysis, two sustainability indicators were calculated: the exergetic efficiency and the exergy renewability. (authors)

Enhanced oil recovery chemicals from renewable wood resources

Energy Technology Data Exchange (ETDEWEB)

Grune, W.N.; Compere, A.L.; Griffith, W.L.; Crenshaw, J.M.

1979-04-01

Most of the wood pulp in the U.S. is produced by cooking, or digesting, wood chips in a chemical solution. These pulping processes have effluent streams which contain dissolved lignins, lignin breakdown products, and carbohydrates. There is a substantial economic incentive to use these materials as feedstocks for the production of high-valued micellar flood chemicals. The pulp and paper industries have practiced chemical recovery for almost a century. The largest chemical recycle processes are the internal recycle of inorganic salts for reuse in pulping. This is coupled with the use of waste organic compounds in the liquor as a fuel for directly-fired evaporation processes. Diversion of effluent and low valued streams for chemical recovery using fermentation, purification, or synthesis methods appears technically feasible in several cases. The use of new recovery processes could yield a variety of different wood-effluent based products. Some of the sugar acids in pulping liquors might be used as sequestering agents in reservoirs where there are large amounts of multivalent cations in flood brines. Fermentation production of high viscosity polymers, sequestering agents, and coagent alcohols appears worth further investigation. Tall oil acids and their derivatives can be used as surfactants in some reservoirs. Some waste constituents may adsorb preferentially on formations and thereby reduce loss of surfactants and other higher-valued chemicals.

Enzymatic hydrolysis of biomimetic bacterial cellulose-hemicellulose composites.

Science.gov (United States)

Penttilä, Paavo A; Imai, Tomoya; Hemming, Jarl; Willför, Stefan; Sugiyama, Junji

2018-06-15

The production of biofuels and other chemicals from lignocellulosic biomass is limited by the inefficiency of enzymatic hydrolysis. Here a biomimetic composite material consisting of bacterial cellulose and wood-based hemicelluloses was used to study the effects of hemicelluloses on the enzymatic hydrolysis with a commercial cellulase mixture. Bacterial cellulose synthesized in the presence of hemicelluloses, especially xylan, was found to be more susceptible to enzymatic hydrolysis than hemicellulose-free bacterial cellulose. The reason for the easier hydrolysis could be related to the nanoscale structure of the substrate, particularly the packing of cellulose microfibrils into ribbons or bundles. In addition, small-angle X-ray scattering was used to show that the average nanoscale morphology of bacterial cellulose remained unchanged during the enzymatic hydrolysis. The reported easier enzymatic hydrolysis of bacterial cellulose produced in the presence of wood-based xylan offers new insights to overcome biomass recalcitrance through genetic engineering. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluating pulp stiffness from fibre bundles by ultrasound

Science.gov (United States)

Karppinen, Timo; Montonen, Risto; Määttänen, Marjo; Ekman, Axel; Myllys, Markko; Timonen, Jussi; Hæggström, Edward

2012-06-01

A non-destructive ultrasonic tester was developed to measure the stiffness of pulp bundles. The mechanical properties of pulp are important when estimating the behaviour of paper under stress. Currently available pulp tests are tedious and alter the fibres structurally and mechanically. The developed tester employs (933 ± 15) kHz tweezer-like ultrasonic transducers and time-of-flight measurement through (9.0 ± 2.5) mm long and (0.8 ± 0.1) mm thick fibre bundles kept at (19.1 ± 0.4) °C and (62 ± 1)% RH. We determined the stiffness of soft wood pulps produced by three kraft pulping modifications: standard kraft pulp, (5.2 ± 0.4) GPa, prehydrolysis kraft pulp, (4.3 ± 0.4) GPa, and alkali extracted prehydrolysis kraft pulp, (3.3 ± 0.4) GPa. Prehydrolysis and alkali extraction processes mainly lowered the hemicellulose content of the pulps, which essentially decreased the fibre-wall stiffness hence impairing the stiffness of the fibre networks. Our results indicate that the method allows ranking of pulps according to their stiffness determined from bundle-like samples taken at an early phase of the papermaking process.

Optimizing cellulose fibrillation for the production of cellulose nanofibrils by a disk grinder

Science.gov (United States)

Chuanshuang Hu; Yu Zhao; Kecheng Li; J.Y. Zhu; Roland Gleisner

2015-01-01

The fibrillation of a bleached kraft eucalyptus pulp was investigated by means of a laboratory-scale disk grinder for the production of cellulose nanofibrils (CNF), while the parameters disk rotating speed, solid loading, and fibrillation duration were varied. The cumulative energy consumption was monitored during fibrillation. The degree of polymerization (DP) and...

EXTRACELLULAR PROTEINS PRODUCED BY DIFFERENT SPECIES OF THE FUNGUS TRICHODERMA ON SECONDARY PAPER MILL SLUDGE SUBSTRATE

Directory of Open Access Journals (Sweden)

Ida Vaskova,

2012-01-01

Full Text Available Kraft pulping is the most commonly used pulping process in the pulp and paper industry. In this process wood chips are chemically delignified using sodium sulfide and sodium hydroxide. Delignification is usually followed by mechanical fiberization and a bleaching process of the resulting wood pulp. In addition to lignin-free wood pulp, this process also produces waste that contains residues of used chemicals, lignin, cellulose, hemicelluloses, and small amounts of other wood components. Because of the worldwide large-scale production of paper, the sludge from paper mills contributes significantly to environmental pollution. Although there have been great efforts being made to utilize this lignin-rich material, sludge is mostly disposed in landfills or incinerated in a boiler. This research project used secondary sludge as a substrate for 7 wood-decay fungi taxonomically belonging to the genus Trichoderma. The examined fungi expressed the capability of consuming sludge components as a carbon source to produce extracellular proteins. The proteins were separated by gel electrophoresis. Before and after fungi cultivation, the sludge was analyzed by Fourier transform infrared spectroscopy (FTIR.

WOOD CELLULOSE ACETATE MEMBRANE 179

African Journals Online (AJOL)

DR. AMINU

2013-06-01

Jun 1, 2013 ... 1988), cosmetics and food additives or pharmaceutical applications (Wellisch .... displaced by sample. Determination of percent α-, β- and γ–cellulose ..... addition, the smaller pore diameter would lead to a greater exclusion of ...

CELLULOSIC NANOCOMPOSITES: A REVIEW

Directory of Open Access Journals (Sweden)

Martin A. Hubbe

2008-08-01

Full Text Available Because of their wide abundance, their renewable and environmentally benign nature, and their outstanding mechanical properties, a great deal of attention has been paid recently to cellulosic nanofibrillar structures as components in nanocomposites. A first major challenge has been to find efficient ways to liberate cellulosic fibrils from different source materials, including wood, agricultural residues, or bacterial cellulose. A second major challenge has involved the lack of compatibility of cellulosic surfaces with a variety of plastic materials. The water-swellable nature of cellulose, especially in its non-crystalline regions, also can be a concern in various composite materials. This review of recent work shows that considerable progress has been achieved in addressing these issues and that there is potential to use cellulosic nano-components in a wide range of high-tech applications.

Effects of Surfactants on the Preparation of Nanocellulose-PLA Composites.

Science.gov (United States)

Immonen, Kirsi; Lahtinen, Panu; Pere, Jaakko

2017-11-17

Thermoplastic composite materials containing wood fibers are gaining increasing interest in the manufacturing industry. One approach is to use nano- or micro-size cellulosic fibrils as additives and to improve the mechanical properties obtainable with only small fibril loadings by exploiting the high aspect ratio and surface area of nanocellulose. In this study, we used four different wood cellulose-based materials in a thermoplastic polylactide (PLA) matrix: cellulose nanofibrils produced from softwood kraft pulp (CNF) and dissolving pulp (CNFSD), enzymatically prepared high-consistency nanocellulose (HefCel) and microcellulose (MC) together with long alkyl chain dispersion-improving agents. We observed increased impact strength with HefCel and MC addition of 5% and increased tensile strength with CNF addition of 3%. The addition of a reactive dispersion agent, epoxy-modified linseed oil, was found to be favorable in combination with HefCel and MC.

High consistency cellulase treatment of hardwood prehydrolysis kraft based dissolving pulp.

Science.gov (United States)

Wang, Qiang; Liu, Shanshan; Yang, Guihua; Chen, Jiachuan; Ni, Yonghao

2015-01-01

For enzymatic treatment of dissolving pulp, there is a need to improve the process to facilitate its commercialization. For this purpose, the high consistency cellulase treatment was conducted based on the hypothesis that a high cellulose concentration would favor the interactions of cellulase and cellulose, thus improves the cellulase efficiency while decreasing the water usage. The results showed that compared with a low consistency of 3%, the high consistency of 20% led to 24% increases of cellulase adsorption ratio. As a result, the viscosity decrease and Fock reactivity increase at consistency of 20% were enhanced from 510 mL/g and 70.3% to 471 mL/g and 77.6%, respectively, compared with low consistency of 3% at 24h. The results on other properties such as alpha cellulose, alkali solubility and molecular weight distribution also supported the conclusion that a high consistency of cellulase treatment was more effective than a low pulp consistency process. Copyright © 2015 Elsevier Ltd. All rights reserved.

High resolution NMR study of cellulose in solid state and in solution

International Nuclear Information System (INIS)

Saint-Germain, Jean

1983-01-01

This research thesis reports the study of native cellulose (cotton) and wood by nuclear magnetic resonance (NMR). As far as the cotton spectrum is concerned, the author assigned resonances which more specifically corresponded to amorphous or crystalline areas. Wood was studied in its bulk condition, and resonances have been determined for the different wood components. The behaviour of cellulose in solution in a solvent has been studied by liquid high resolution NMR. The solvation mechanism has been determined and a study of model components of the macromolecule allowed a conformational study of cellulose in this solvent to be performed. Bi-dimensional NMR and longitudinal relaxation time measurements highlighted the existence of an intramolecular hydrogen bond in the cellulose in solution [fr

Radiation processing of wood-plastic composites

International Nuclear Information System (INIS)

Czvikovszky, T.

1992-01-01

There are three main types of radiation-processed composite material derived from plastics and fibrous natural polymers. The first are the monomer-impregnated, radiation-treated wood-plastic composites (WPC). They became a commercial success in the early 1970s. More recently, work has focused on improving the WPCs by creating in them interpenetrating network (IPN) systems by the use of appropriate multifunctional oligomers and monomers. The main kinetic features of radiation-initiated chain polymerization remain applicable even in impregnated wood. The second type are the plastics filled or reinforced with dispersed wood fiber or other cellulosics (WFRP). In their case, radiation processing offers a new opportunity to apply radiation-reactive adhesion promoters between wood or cellulosic fibers and the thermoplastic matrices. The third type are the laminar composites made by electron beam coating of wood-based agglomerate sheets and boards. This chapter reviews the industrial applications and the radiation processing of the three types of the wood-plastic composites and indicates future trends. (orig.)

Quality evaluation of dissolving pulp fabricated from banana plant stem and its potential for biorefinery.

Science.gov (United States)

Das, Atanu Kumar; Nakagawa-Izumi, Akiko; Ohi, Hiroshi

2016-08-20

The study was conducted to evaluate the quality of dissolving pulp of Musa sapientum L. (banana) plant stem and its potential for biorefinery. Introduction of pre-hydrolysis prior to any alkaline pulping process helps to reduce the content of hemicellulose and consequently produce acceptably high content of cellulose pulp. Water pre-hydrolysis was done at 150°C for 90min. The amount of lignin, xylan and glucan in the extracted pre-hydrolysis liquor (PHL) was 1.6, 4.9 and 1.6%, respectively. Pulping of pre-extracted chips was done following soda-AQ, alkaline sulfite and kraft process. The ratio of chip to liquor was 1:7 for both pre-hydrolysis and pulping. The kraft pulping process with 20% active alkali and 25% sulfidity at 150°C for 90min showed the best result. The lowest kappa number was 26.2 with a considerable pulp yield of 32.7%. The pulp was bleached by acidic NaClO2 and the consistency was 10% based on air-dried pulp. The lowest amount of 7% NaClO2 was used for the bleaching sequence of D0ED1ED2. After D0ED1ED2 bleaching, the pulp showed that α-cellulose, brightness and ash were 91.9, 77.9 and 1.6% respectively. The viscosity was 19.9cP. Hence, there is a possibility to use banana plant stem as a raw material for dissolving grade pulp and other bioproducts. Copyright © 2016 Elsevier Ltd. All rights reserved.

PENGGUNAAN ASAM PERASETAT PADA PROSES DELIGNIFIKASI PULP ACETOSOLV DARI AMPAS TEBU DAN BAMBU BETUNG

Directory of Open Access Journals (Sweden)

Ahmad Sapta Zuidar

2014-07-01

Full Text Available Acetosolv process produced dark pulp because of the high lignin content.  Therefore ,  delignification  process is needed. This process uses peracetic acid to improve pulp qualities. The objective of this research was to determine the effect of different concentrations of peracetic acid against the characteristics of pulp acetosolv from bagasse and bamboo betung.  The research was arranged in a Complete Randomized Block Design with a single treatment and 4 replications.  The treatment used peracetic acid with six levels concentration (9%, 11%, 13%, 15%, 17%, 19% at a temperature of 85oC for 3 hours. The homogenity and additivity of the data were  analyzed using Bartlett and Tuckey Tests, then they were analyze for ANOVA to see if there is any difference among means, and then processed further using  Least Significant Difference at level of 1% and 5%.  The results showed that the concentration of peracetic acid had significant effect on yield, cellulose, hemicellulose, lignin, and organoleptic color pulp from bagasse and bamboo betung.  The best results showed that the concentration of peracetic acid 15% with cooking duration of  3 hours gave the best pulp. The pulp contained 85.837% of cellulose , 7.757% of hemicellulose , 1.758% of lignin , 73.048% of yield  and  the average organoleptic score for the pulp color was 4.3. Keywords:   acetosolv pulp,  baggase, bamboo,  delignification, paracetic acid

Structural and morphological characterization of cellulose pulp

CSIR Research Space (South Africa)

Ocwelwang, A

2015-09-01

Full Text Available Understanding the structure of cellulose is of utmost importance in order to enhance its accessibility and reactivity to chemical processing. Therefore, the aim of this study was to evaluate the effect of ultrasound pretreatment on the structure...

Fiber length and pulping characteristics of switchgrass, alfalfa stems, hybrid poplar and willow biomasses.

Science.gov (United States)

Ai, Jun; Tschirner, Ulrike

2010-01-01

Switchgrass (Panicum virgatum), alfalfa stems (Medicago sativa), second year growth hybrid poplar (Populus) and willow (Salix spp.) were examined to determine fiber characteristics, pulping behavior and paper properties. Alfalfa stems and switchgrass both showed length weighted average fiber length (LWW) of 0.78 mm, a very narrow fiber length distribution and high fines content. Willow and hybrid poplar have lower fines content but a very low average fiber length (0.42 and 0.48 mm LWW). In addition, the four biomass species showed distinctly different chemical compositions. Switchgrass was defibered successfully using Soda and Soda Anthraquinone (AQ) pulping and demonstrated good paper properties. Both fast-growing wood species pulped well using the Kraft process, and showed acceptable tensile strength, but low tear strength. Alfalfa stems reacted very poorly to Soda and Soda AQ pulping but responded well to Kraft and Kraft AQ. Pulps with tensile and tear strength considerably higher than those found for commercial aspen pulps were observed for alfalfa. All four biomass species examined demonstrated low pulp yield. The highest yields were obtained with poplar and switchgrass (around 43%). Considering the short fibers and low yields, all four biomass types will likely only be used in paper manufacturing if they offer considerable economic advantage over traditional pulp wood.

Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill Características químicas e polpação Kraft de madeira de tração de Eucalyptus globulus labill

Directory of Open Access Journals (Sweden)

María Graciela Aguayo

2012-12-01

Full Text Available Tension (TW and opposite wood (OW of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively. The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EOD1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.Madeira de tração e oposta de árvores de Eucalyptus globulus foram analisadas quanto a suas características químicas e produção de polpa Kraft. A caracterização química da madeira de tração (TW de Eucalyptus globulus Labill. mostrou um conteúdo similar de celulose, alto conteúdo de xilanas e baixo conteúdo de lignina quando comparada com a madeira oposta (OW de uma mesma árvore. O conteúdo de lignina foi 16% menor e contém 32% mais unidades siringila em TW que em OW. O aumento das unidades siringila favoreceu a formação de ligações �

PROCESS FOR THE PRODUCTION OF DISSOLVING PULP FROM TREMA ORIENTALIS (NALITA) BY PREHYDROLYSIS KRAFT AND SODA-ETHYLENEDIAMINE (EDA) PROCESS

OpenAIRE

M. A. Quaiyyum; A. Noori; Labooni Ahsan; M. Sarwar Jahan

2008-01-01

This paper presents a preliminary study for the production of dissolving pulp from Trema orientalis (Nalita). Water prehydrolysis kraft and soda-ethylenediamine (EDA) pulping for the production of dissolving pulp from T. orientalis was investigated. Prehydrolysis at 150 and 170 oC did not produce pulp with high α-cellulose content when using the kraft process. But addition of 0.25 % H2SO4 in prehydrolysis liquor increased the purity of the pulp with the sacrifice of pulp yield and viscosity. ...

Possible mechanism for anthraquinone species diffusion in alkaline pulping

Science.gov (United States)

X.-S. Chai; J. Samp; Q.X. Hou; S.-H Yoon; J.Y. Zhu

2007-01-01

An analysis of the effectiveness of anthraquinone (AQ) in kraft-AQ pulping in terms of its mechanism of transport has been conducted. Our previous work showed that caustic solutions of wood lignin can decrease the membrane exclusion for anthraquinones, i.e., the presence of wood lignin enhances the ability of AQ to pass through a membrane when a reducing agent is...

Isolation and characterization of pulp from sugarcane bagasse and rice straw

International Nuclear Information System (INIS)

Saiful Azhari, S.; Suhardy, D.; Kasim, F.H; Nazry Saleh, M.

2007-01-01

The amount of sugarcane bagasse and rice straw in the state of Perlis (Malaysia) is abundant while its utilization is still limited. One of the alternatives for the bagasse and straw utilization is as pulp raw material. This paper reviews on pulp from sugarcane bagasse and rice straw and its suitability for paper production. In this study, the pulp was extracted by the Soxhlet extraction method. The objective of this study was to investigate the cellulose, lignin and silica content of the pulp from sugarcane bagasse and rice straw. For rice straw, the presence of large amount of pentosanes in the pulp and black liquors, which also contain silica were decreased the using of straw in the paper industry. Therefore, formic acid pulping and NaOH treatment are studied to reduce or prevent silica. The isolated pulp samples were further characterized by Scanning Electron Microscope (SEM) to investigate their fiber dimensions. (Author)

Pulp and paper from blue agave waste from tequila production.

Science.gov (United States)

Idarraga, G; Ramos, J; Zuñiga, V; Sahin, T; Young, R A

1999-10-01

Pulping of blue agave waste, from the production of tequila, was evaluated by both chemical and biomechanical pulping processes. Two conventional and two organosolv systems were used to pulp the agave waste under a standard set of conditions. The soda-ethanol process was superior in terms of delignification and pulp properties in comparison to the soda and ethanol organosolv processes for pulping of agave waste; however, the kraft process gave the best strength properties. In general, the strength of the agave waste pulps was rather poor in comparison to wood and other agro-based pulps; however, the tear strength was relatively high. This result is typical of poorly bonded sheets and may be due to the coarseness of the agave fibers and/or loss of hemicelluloses in the steaming process for the tequila production. Fungal treatment of the agave waste with Ceriporiopsis subvermispora reduced the energy consumption for mechanical refining but gave biomechanical pulps with inferior strength properties. The blue agave chemical pulps should be suitable for blending with softwood kraft pulps for publication grade paper.

Incorporating biopulping technology into wood yard operations

Science.gov (United States)

Gary M. Scott; Eric. Horn; Masood. Akhtar; Ross E. Swaney; Michael J. Lentz; David F. Shipley

1998-01-01

Biopulping is the treatment of wood chips and other lignocellulosic materials with lignin-degrading fungi prior to pulping. Ten years of industry-sponsored research has demonstrated the technical feasibility of the technology for mechanical pulping at a laboratory scale. Two 50-ton outdoor chip pile trials recently conducted at the USDA Forest Service, Forest Products...

ON THE RECOVERY OF HEMICELLULOSE BEFORE KRAFT PULPING

Directory of Open Access Journals (Sweden)

Carlos Vila,

2012-07-01

Full Text Available To assess the feasibility of implementing hemicellulose recovery stages in kraft mills, Eucalyptus globulus wood samples were subjected to aqueous treatments with hot, compressed water (autohydrolysis processing to achieve partial dissolution of xylan. Autohydrolyzed solids were subjected to kraft pulping under selected conditions to yield a pulp of low kappa number, and to an optimized TCF bleaching sequence made up of three stages (alkaline oxygen delignification, chelating, and pressurized hydrogen peroxide, with minimized additions of pulping and bleaching chemicals. The final product had a relatively low kappa number (1.4, 641 mL/g ISO intrinsic viscosity, and 86.4% brightness.

Chapter 1.4: Spatially Resolved Characterization of CNC-Polypropylene composite by Confocal Raman Microscopy

Science.gov (United States)

Umesh Agarwal; Ronald Sabo; Richard Reiner; Craig Clemons; Alan Rudie

2013-01-01

Raman spectroscopy was used to analyze cellulose nanocrystal (CNC)-polypropylene (PP) composites and to investigate the spatial distribution of CNCs in extruded composite filaments. Three composites were made from two forms of nanocellulose (CNCs from wood pulp and the nanoscale fraction of microcrystalline cellulose), and two of the three composites...

Physical properties and morphology of films prepared from microfibrillated cellulose and microfibrillated cellulose in combination with amylopectin

DEFF Research Database (Denmark)

Plackett, David; Anturi, Harvey; Hedenqvist, Mikael

2010-01-01

Two types of microfibrillated cellulose (MFC) were prepared using either a sulfite pulp containing a high amount of hemicellulose (MFC 1) or a carboxymethylated dissolving pulp (MFC 2). MFC gels were then combined with amylopectin solutions to produce solvent-cast MFC-reinforced amylopectin films....... Tensile testing revealed that MFC 2-reinforced films exhibited a more ductile behavior and that MFC 1-reinforced films had higher modulus of elasticity (E-modulus) at MFC loadings of 50 wt % or higher. Pure MFC films had relatively low oxygen permeability values when data were compared with those...

The biosorption of Cd2+ ions by wood pulp of Pinus negra Arnold

International Nuclear Information System (INIS)

Loucka, T.; Janos, P.

2001-01-01

Biosorption is one of those processes that use biomass (mostly inanimate) for elimination of various chemical substances (e.g. heavy metals) from environment. Until now algae have been studied as bio-sorbents in most cases, but we can also take advantage of wood pulp (or sawdust) that is normal waste material resulting in large amounts from various productions. Considering the fact that bio-sorbent can be taken as natural ion exchanger containing slightly acidic or basic functional groups (2,3,4), it is necessary to suppose that part of functional groups is filled by various metals before starting the measurements. Substituting these bound metallic cations by protonization we can gain biomass in given condition and some important information about the content of cations bound to bio-sorbent through ion exchange. The material used for biosorption observation was sawdust of Pinus negra Arnold. For measurements we used the part which passed through the 0.6 mm sieve. By dehydrating at the 1200 C for the time of 24 hours we gained the water part that was 5.44% of original weight

Renewable Wood Pulp Paper Reactor with Hierarchical Micro/Nanopores for Continuous-Flow Nanocatalysis.

Science.gov (United States)

Koga, Hirotaka; Namba, Naoko; Takahashi, Tsukasa; Nogi, Masaya; Nishina, Yuta

2017-06-22

Continuous-flow nanocatalysis based on metal nanoparticle catalyst-anchored flow reactors has recently provided an excellent platform for effective chemical manufacturing. However, there has been limited progress in porous structure design and recycling systems for metal nanoparticle-anchored flow reactors to create more efficient and sustainable catalytic processes. In this study, traditional paper is used for a highly efficient, recyclable, and even renewable flow reactor by tailoring the ultrastructures of wood pulp. The "paper reactor" offers hierarchically interconnected micro- and nanoscale pores, which can act as convective-flow and rapid-diffusion channels, respectively, for efficient access of reactants to metal nanoparticle catalysts. In continuous-flow, aqueous, room-temperature catalytic reduction of 4-nitrophenol to 4-aminophenol, a gold nanoparticle (AuNP)-anchored paper reactor with hierarchical micro/nanopores provided higher reaction efficiency than state-of-the-art AuNP-anchored flow reactors. Inspired by traditional paper materials, successful recycling and renewal of AuNP-anchored paper reactors were also demonstrated while high reaction efficiency was maintained. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Production of ethanol from cassava pulp via fermentation with a surface-engineered yeast strain displaying glucoamylase

Energy Technology Data Exchange (ETDEWEB)

Kosugi, Akihiko; Murata, Yoshinori; Arai, Takamitsu; Mori, Yutaka [Post-harvest Science and Technology Division, Japan International Research Center for Agricultural Sciences (JIRCAS), 1-1 Ohwashi, Tsukuba, Ibaraki 305-8686 (Japan); Kondo, Akihiko [Department of Chemical Science and Engineering, Faculty of Engineering, Kobe University, Nada-ku, Kobe, 657-8501 (Japan); Ueda, Mitsuyoshi [Department of Applied Biochemistry, Division of Applied Life Sciences, Graduate School of Agriculture, Kyoto University, Sakyo-ku, Kyoto 606-8502 (Japan); Vaithanomsat, Pilanee; Thanapase, Warunee [Nanotechnology and Biotechnology Division, Kasetsart Agricultural and Agro-Industrial Product Improvement Institute (KAPI), Kasetsart University, 50 Chatuchak, Ladyao, Bangkok 10900 (Thailand)

2009-05-15

Cassava (Manihot esculenta Crantz) pulp, produced in large amounts as a by-product of starch manufacturing, is a major biomass resource in Southeast Asian countries. It contains abundant starch (approximately 60%) and cellulose fiber (approximately 20%). To effectively utilize the cassava pulp, an attempt was made to convert its components to ethanol using a sake-brewing yeast displaying glucoamylase on the cell surface. Saccharomyces cerevisiae Kyokai no. 7 (strain K7) displaying Rhizopus oryzae glucoamylase, designated strain K7G, was constructed using the C-terminal-half region of {alpha}-agglutinin. A sample of cassava pulp was pretreated with a hydrothermal reaction (140 C for 1 h), followed by treatment with a Trichoderma reesei cellulase to hydrolyze the cellulose in the sample. The K7G strain fermented starch and glucose in pretreated samples without addition of amylolytic enzymes, and produced ethanol in 91% and 80% of theoretical yield from 5% and 10% cassava pulp, respectively. (author)

Effects of Surfactants on the Preparation of Nanocellulose-PLA Composites

Directory of Open Access Journals (Sweden)

Kirsi Immonen

2017-11-01

Full Text Available Thermoplastic composite materials containing wood fibers are gaining increasing interest in the manufacturing industry. One approach is to use nano- or micro-size cellulosic fibrils as additives and to improve the mechanical properties obtainable with only small fibril loadings by exploiting the high aspect ratio and surface area of nanocellulose. In this study, we used four different wood cellulose-based materials in a thermoplastic polylactide (PLA matrix: cellulose nanofibrils produced from softwood kraft pulp (CNF and dissolving pulp (CNFSD, enzymatically prepared high-consistency nanocellulose (HefCel and microcellulose (MC together with long alkyl chain dispersion-improving agents. We observed increased impact strength with HefCel and MC addition of 5% and increased tensile strength with CNF addition of 3%. The addition of a reactive dispersion agent, epoxy-modified linseed oil, was found to be favorable in combination with HefCel and MC.

Cellulose esters synthesized using a tetrabutylammonium acetate and dimethylsulfoxide solvent system

Science.gov (United States)

Yu, Yongqi; Miao, Jiaojiao; Jiang, Zeming; Sun, Haibo; Zhang, Liping

2016-07-01

Cellulose acetate (CA) and cellulose acetate propionate (CAP) were homogeneously synthesized in a novel tetrabutylammonium acetate/dimethyl sulfoxide (DMSO) solvent system, without any catalyst, at temperatures below 70 °C. The molecular structures of the cellulose esters (CEs) and distributions of the substituents in the anhydroglucose repeating units were determined using 13C cross-polarization magic angle spinning nuclear magnetic resonance spectroscopy, and the degree of substitution (DS) values were determined using 1H nuclear magnetic resonance spectroscopy. The structures of the CEs, regenerated cellulose (RC), and pulp were determined using Fourier transform infrared spectroscopy. The thermal properties of the products were determined using thermogravimetric analysis. The temperatures of initial decomposition of the CEs were up to 40 °C higher than those of the RC and pulp. All the CEs were highly soluble in DMSO, but were insoluble in acetone. CAs with DS values less than 2.6 swelled or were poorly dissolved in CHCl3, but those with DS values above 2.9 dissolved rapidly. CAPs with DS values above 2.6 had good solubilities in ethyl acetate.

Nanocellulose steps up on stage

Energy Technology Data Exchange (ETDEWEB)

McCormick, C.

2010-07-15

Canadian researchers and manufacturers are world leaders in the development of new applications for nanocellulose, a principal component of trees. Nanocrystalline cellulose (NCC) is a natural substance first isolated in 1949. The cellulose in pulp is approximately 70 per cent NCC. Canadian researchers have found a way to extract NCC from wood in industrial quantities. A batch process has been developed at a demonstration plant in Windsor. Other researchers are now developing new NCC applications for strengthening wood varnish, improving paint texture, and adding it to polymers for additional strength. A consortium of industry partners and researchers are now preparing joint agreements with manufacturers to investigate wood coatings and composites; improve NCC's compatibility with polymers; and examine applications of its optical properties in pulp and paper processes. NCC may also be used in aircraft design as well as in automotive products. 1 fig.

The Effects of CaCO3 Coated Wood Free Paper Usage as Filler on Water Absorption, Mechanical and Thermal Properties of Cellulose-High Density Polyethylene Composites

Directory of Open Access Journals (Sweden)

Emrah PEŞMAN

2016-11-01

Full Text Available In this study some physical, mechanical and thermal characteristics of high density polyethylene (HDPE and CaCO3 coated/pigmented wood free paper fiber composites were investigated. The fillers used in this study were uncoated cellulose, 5.8 %, 11.5 %, 16.5 % and 23.1 % CaCO3 coated wood free paper fibers. Each filler type was mixed with HDPE at 40% by weight fiber loading. In this case, the ratio of CaCO3 in plastic composites were calculated as 0 %, 2.3 %, 4.6 %, 6.6 % and 9.2 % respectively. Increased CaCO3 ratio improved the moisture resistant, flexural and tensile strength of cellulose-HDPE composites. However, the density of the cellulose-HDPE composites increased with CaCO3 addition. Energy Dispersive Spectroscopy on Scanning Electron Microscope analysis demonstrated the uniform distribution of CaCO3 and cellulose fiber in plastic matrix. In addition, the thermal properties of fiber plastic composites were investigated. The results of Differential scanning calorimetry analysis revealed that the crystallinity of the samples decreased with increasing CaCO3 content. Consequently, this work showed that CaCO3 coated waste paper fibers could be used as reinforcing filler against water absorption in thermoplastic matrix.DOI: http://dx.doi.org/10.5755/j01.ms.22.4.14222

Cellulose digestion in Monochamus marmorator Kby. (coleoptera: Cerambycidae): role of acquired fungal enzymes

Energy Technology Data Exchange (ETDEWEB)

Kukol, J.J.; Martin, M.M.

1986-05-01

Larvae of the balsam fir sawyer, Monochamus marmorator Kby. (Coleoptera, Cerambycidae), contain midgut digestive enzymes active against hemicellulose and cellulose. Cellulases from larvae fed on balsam fir wood infected with the fungus, Trichoderma harzianum Rifai (Deuteromycetes, Moniliales, Moniliaceae), were found to be identical to those of the cellulase complex produced by this fungus when compared using chromatography, electrophoresis, and isofocusing. When larvae are maintained on a fungusfree diet, their midgut fluids lack cellulolytic activity, and they are unable to digest cellulose. Cellulolytic capacity can be restored by feeding the larvae wood permeated by fungi. We conclude that the enzymes which enable M. marmorator larvae to digest cellulose are not produced by the larvae. Instead, the larvae acquire the capacity to digest cellulose by ingesting active fungal cellulases while feeding in fungus-infected wood.

Cellulose digestion in Monochamus marmorator Kby. (coleoptera: Cerambycidae): role of acquired fungal enzymes

International Nuclear Information System (INIS)

Kukol, J.J.; Martin, M.M.

1986-01-01

Larvae of the balsam fir sawyer, Monochamus marmorator Kby. (Coleoptera, Cerambycidae), contain midgut digestive enzymes active against hemicellulose and cellulose. Cellulases from larvae fed on balsam fir wood infected with the fungus, Trichoderma harzianum Rifai (Deuteromycetes, Moniliales, Moniliaceae), were found to be identical to those of the cellulase complex produced by this fungus when compared using chromatography, electrophoresis, and isofocusing. When larvae are maintained on a fungusfree diet, their midgut fluids lack cellulolytic activity, and they are unable to digest cellulose. Cellulolytic capacity can be restored by feeding the larvae wood permeated by fungi. We conclude that the enzymes which enable M. marmorator larvae to digest cellulose are not produced by the larvae. Instead, the larvae acquire the capacity to digest cellulose by ingesting active fungal cellulases while feeding in fungus-infected wood

MASSAHAKE whole tree harvesting method for pulp raw-material and fuel -- R&D in 1993--1998

Energy Technology Data Exchange (ETDEWEB)

Asplund, D.A.; Ahonen, M.A. [Technical Research Centre of Finland, Jyvaeskylae (Finland)

1993-12-31

In Finland biofuels and hydropower are the only indigenous fuels available. Peat, wood and wood derived fuels form about 18% of total primary energy requirement. The largest wood and wood fuel user in Finland is wood processing industry, paper, pulp, sawmills. Due to silvicultural activities the growth of forests has developed an instant need for first thinnings. This need is about 12% of total stem wood growth. With conventional harvesting methods this would produce about 8 mill. m{sup 3} pulp raw material and 2 mill. m{sup 3} wood fuel. By using integrated harvesting methods about 12 mill. m{sup 3} pulp raw material and 8 mill. m{sup 3} (about 1, 3 mill. toe) fuel could be produced. At the moment, there is no economically profitable method for harvesting first thinning trees for industrial use or energy production. Hence, there are a few ongoing research projects aiming at solving the question of integrated harvesting. MASSAHAKE chip purification method has been under R&D since 1987. Research with continuous experimental line (capacity 5--10 loose-m{sup 3}) has been done in 1991 and 1992. The research has concentrated on pine whole tree chip treatment, but preliminary tests with birch whole tree chips has been done. The experiment line will be modified for birth whole tree chips during 1993. Based on the research results more than 60% of the whole tree chips can be separated to pulp raw material with < 1% bark content. This amount is 1.5--2 times more than with present technology. The yield of fuel fraction is 2--4 times higher compared to present methods. Fuel fraction is homogeneous and could be used in most furnaces for energy production. By replacing fossil fuels with wood fuel in energy production it is possible to reduce CO{sub 2}-emissions significantly. This paper presents the wood fuel research areas in Finland and technical potential of MASSAHAKE-method including the plant for building a demonstration plant based on this technology.

Alkaline Pulping and Bleaching of Acacia auriculiformis Grown in Bangladesh

OpenAIRE

JAHAN, M. Sarwar; SABINA, Rowshan; RUBAIYAT, Arjumand

2014-01-01

The physical, chemical, and morphological characteristics of Acacia auriculiformis were evaluated in terms of its suitability for papermaking. The fiber length (1.1 mm) of A. auriculiformis in this study was within the range of tropical hardwoods. The lignin content in A. auriculiformis was 19.4% and a-cellulose 44.1%, which was within the range of other acacias, but that of extractives was higher. Soda, soda-AQ, and kraft processes were studied in pulping. Screened pulp yield was increased w...

Surface chemistry of cellulose : from natural fibres to model surfaces

NARCIS (Netherlands)

Kontturi, E.J.

2005-01-01

The theme of the thesis was to link together the research aspects of cellulose occurring in nature (in natural wood fibres) and model surfaces of cellulose. Fundamental changes in cellulose (or fibre) during recycling of paper was a pragmatic aspect which was retained throughout the thesis with

Performance of improved bacterial cellulose application in the production of functional paper.

Science.gov (United States)

Basta, A H; El-Saied, H

2009-12-01

The purpose of this work was to study the feasibility of producing economic flame retardant bacterial cellulose (BC) and evaluating its behaviour in paper production. This type of BC was prepared by Gluconacetobacter subsp. xylinus and substituting the glucose in the cultivation medium by glucose phosphate as a carbon source; as well as using corn steep liquor as a nitrogen source. The investigated processing technique did not dispose any toxic chemicals that pollute the surroundings or cause unacceptable effluents, making the process environmentally safe. The fire retardant behaviour of the investigated BC has been studied by non-isothermal thermogravimetric analysis (TGA & DTGA). The activation energy of each degradation stage and the order of degradation were estimated using the Coats-Redfern equation and the least square method. Strength, optical properties, and thermogravimetric analysis of BC-phosphate added paper sheets were also tested. The study confirmed that the use of glucose phosphate along with glucose was significant in the high yield production of phosphate containing bacterial cellulose (PCBC1); more so than the use of glucose phosphate alone (PCBC2). Incorporating 5% of the PCBC with wood pulp during paper sheet formation was found to significantly improve kaolin retention, strength, and fire resistance properties as compared to paper sheets produced from incorporating bacterial cellulose (BC). This modified BC is a valuable product for the preparation of specialized paper, in addition to its function as a fillers aid.

Opportunities of Bamboo for Industrial Processes

NARCIS (Netherlands)

Janssen, J.J.A.; Erkelens, P.A.; Jonge, S. de; Vliet, A.A.M. van

2000-01-01

Bamboo as resource for industrial raw material has many opportunities: It contains a 40 percent cellulose, with a fibre length of 3 to 4 mm, more than wood. This can be used as pulp in the paper industry or as cellulose. The fibres also can be used for fibreboard or for furniture parts. Bamboo

STORAGE OF CHEMICALLY PRETREATED WHEAT STRAW – A MEANS TO ENSURE QUALITY RAW MATERIAL FOR PULP PREPARATION

Directory of Open Access Journals (Sweden)

Terttu Heikkilä

2010-07-01

Full Text Available The aim of this study was to evaluate effects of chemical pretreatment and storage on non-wood pulping and on pulp quality. The processes studied were hot water treatment followed by alkaline peroxide bleaching or soda cooking. The results showed that it is possible to store wheat straw outside for at least one year without significant changes in the raw material chemical composition and without adverse effects on the resulting pulp quality. The results are significant to the industry using non-woods to ensure the availability and the quality of the raw-material throughout the year in spite of the short harvesting time.

Branch Wood Decomposition of Tree Species in a Deciduous Temperate Forest in Korea

Directory of Open Access Journals (Sweden)

Sangsub Cha

2017-05-01

Full Text Available Woody debris, which is supplied by branch litter, is an important component of forest ecosystems as it contains large quantities of organic matter and nutrients. We evaluated changes in branch wood dry weight and nutrient content of six common species (Fraxinus rhynchophylla, Pinus densiflora, Prunus sargentii, Quercus mongolica, Acer pseudosieboldianum, and Symplocos chinensis for. pilosa in a deciduous temperate forest in Korea for 40 months. Branch wood disk samples 1.4–1.6 cm thick were cut, and mass loss was measured over time using the litterbag method. No significant differences in mass loss were recorded among the six tree species. Further, mass loss was negatively correlated with initial lignin concentration and positively correlated with both initial cellulose concentration and wood density for each species. Species with high wood cellulose content had high wood density while the lignin content in wood was relatively low. Accordingly, cellulose contributed to wood density, creating a relatively lower lignin content, and the decreased lignin concentration increased the wood decomposition rate.

Delignified and Densified Cellulose Bulk Materials with Excellent Tensile Properties for Sustainable Engineering.

Science.gov (United States)

Frey, Marion; Widner, Daniel; Segmehl, Jana S; Casdorff, Kirstin; Keplinger, Tobias; Burgert, Ingo

2018-02-07

Today's materials research aims at excellent mechanical performance in combination with advanced functionality. In this regard, great progress has been made in tailoring the materials by assembly processes in bottom-up approaches. In the field of wood-derived materials, nanocellulose research has gained increasing attention, and materials with advanced properties were developed. However, there are still unresolved issues concerning upscaling for large-scale applications. Alternatively, the sophisticated hierarchical scaffold of wood can be utilized in a top-down approach to upscale functionalization, and one can profit at the same time from its renewable nature, CO 2 storing capacity, light weight, and good mechanical performance. Nevertheless, for bulk wood materials, a wider multipurpose industrial use is so far impeded by concerns regarding durability, natural heterogeneity as well as limitations in terms of functionalization, processing, and shaping. Here, we present a novel cellulose bulk material concept based on delignification and densification of wood resulting in a high-performance material. A delignification process using hydrogen peroxide and acetic acid was optimized to delignify the entire bulk wooden blocks and to retain the highly beneficial structural directionality of wood. In a subsequent step, these cellulosic blocks were densified in a process combining compression and lateral shear to gain a very compact cellulosic material with entangled fibers while retaining unidirectional fiber orientation. The cellulose bulk materials obtained by different densification protocols were structurally, chemically, and mechanically characterized revealing superior tensile properties compared to native wood. Furthermore, after delignification, the cellulose bulk material can be easily formed into different shapes, and the delignification facilitates functionalization of the bioscaffold.

POLYPYRROLE AND POLYPYRROLE/WOOD-DERIVED MATERIALS CONDUCTING COMPOSITES: A REVIEW

Directory of Open Access Journals (Sweden)

Davide Beneventi Mail

2011-07-01

Full Text Available Wood and cellulose derivatives, in both fibrous and water-soluble macromolecular form, are emerging as outstanding candidates for organic electronics applications due to their large-scale availability, low cost, and easy processability. Paper and wood fibre-based derivatives are considered to be materials of choice as supports for communication world-wide. The interest in producing inexpensive and universally available conducting polymer/cellulose fibres substrates resides in the possibility of creating new materials that can be used for a broad range of advanced applications. For instance, PPy/cellulose fibres composites can be used for the preparation of energy storage devices thanks to the conjugation of the high specific area of cellulose fibres and the electrochemical properties of PPy. Other possible applications of such composites are in the area of the antistatic materials, sensors, electromagnetic interference shielding materials, smart packaging, and tissues. Concerning the woody polymers, some of them (i.e. cellulose derivatives also exhibit biocompatibility, as well as film-forming properties and transparency. In combination with the electrical properties of PPy, these features make PPy/macromolecular cellulose composites suitable for applications as displays, lighting, and photovoltaics. Due to their chemical structure, macromolecular wood derivatives have been proposed with success as enhancing conductivity additives in Py polymerisation. The aim of the present review is to provide an overview of PPy chemistry and of the most relevant advances attained in the production of PPy/wood derived materials conducting composites.

Acetylation of wood components and fourier transform infra-red ...

African Journals Online (AJOL)

In this study, the reactivity of wood components with acetic anhydride or vinyl acetate was studied. It was found that the reactivity of wood components was virgin wood flour > holocellulose >> a-cellulose. Acetylation of Turkish pine or cedar wood flour with acetic anhydride was significantly improved in the presence of ...

Characterization of Cellulose Synthesis in Plant Cells

Science.gov (United States)

Maleki, Samaneh Sadat; Mohammadi, Kourosh; Ji, Kong-shu

2016-01-01

Cellulose is the most significant structural component of plant cell wall. Cellulose, polysaccharide containing repeated unbranched β (1-4) D-glucose units, is synthesized at the plasma membrane by the cellulose synthase complex (CSC) from bacteria to plants. The CSC is involved in biosynthesis of cellulose microfibrils containing 18 cellulose synthase (CesA) proteins. Macrofibrils can be formed with side by side arrangement of microfibrils. In addition, beside CesA, various proteins like the KORRIGAN, sucrose synthase, cytoskeletal components, and COBRA-like proteins have been involved in cellulose biosynthesis. Understanding the mechanisms of cellulose biosynthesis is of great importance not only for improving wood production in economically important forest trees to mankind but also for plant development. This review article covers the current knowledge about the cellulose biosynthesis-related gene family. PMID:27314060

Characterization of Cellulose Synthesis in Plant Cells

Directory of Open Access Journals (Sweden)

Samaneh Sadat Maleki

2016-01-01

Full Text Available Cellulose is the most significant structural component of plant cell wall. Cellulose, polysaccharide containing repeated unbranched β (1-4 D-glucose units, is synthesized at the plasma membrane by the cellulose synthase complex (CSC from bacteria to plants. The CSC is involved in biosynthesis of cellulose microfibrils containing 18 cellulose synthase (CesA proteins. Macrofibrils can be formed with side by side arrangement of microfibrils. In addition, beside CesA, various proteins like the KORRIGAN, sucrose synthase, cytoskeletal components, and COBRA-like proteins have been involved in cellulose biosynthesis. Understanding the mechanisms of cellulose biosynthesis is of great importance not only for improving wood production in economically important forest trees to mankind but also for plant development. This review article covers the current knowledge about the cellulose biosynthesis-related gene family.

Sugar, acid and furfural quantification in a sulphite pulp mill: Feedstock, product and hydrolysate analysis by HPLC/RID.

Science.gov (United States)

Llano, Tamara; Quijorna, Natalia; Andrés, Ana; Coz, Alberto

2017-09-01

Waste from pulp and paper mills consist of sugar-rich fractions comprising hemicellulose derivatives and cellulose by-products. A complete characterisation of the waste streams is necessary to study the possibilities of an existing mill. In this work, four chromatographic methods have been developed to obtain the most suitable chromatographic method conditions for measuring woody feedstocks, lignocellulosic hydrolysates and cellulose pulp in sulphite pulping processes. The analysis of major and minor monosaccharides, aliphatic carboxylic acids and furfurals has been optimised. An important drawback of the spent liquors generated after sulphite pulping is their acidic nature, high viscosity and adhesive properties that interfere in the column lifetime. This work recommends both a CHO-782Pb column for the sugar analysis and an SH-1011 resin-based cross-linked gel column to separate low-molecular-weight chain acids, alcohols and furfurals. Such columns resulted in a good separation with long lifetime, wide pH operating range and low fouling issues.

Direct ethanol production from cassava pulp using a surface-engineered yeast strain co-displaying two amylases, two cellulases, and β-glucosidase.

Science.gov (United States)

Apiwatanapiwat, Waraporn; Murata, Yoshinori; Kosugi, Akihiko; Yamada, Ryosuke; Kondo, Akihiko; Arai, Takamitsu; Rugthaworn, Prapassorn; Mori, Yutaka

2011-04-01

In order to develop a method for producing fuel ethanol from cassava pulp using cell surface engineering (arming) technology, an arming yeast co-displaying α-amylase (α-AM), glucoamylase, endoglucanase, cellobiohydrase, and β-glucosidase on the surface of the yeast cells was constructed. The novel yeast strain, possessing the activities of all enzymes, was able to produce ethanol directly from soluble starch, barley β-glucan, and acid-treated Avicel. Cassava is a major crop in Southeast Asia and used mainly for starch production. In the starch manufacturing process, large amounts of solid wastes, called cassava pulp, are produced. The major components of cassava pulp are starch (approximately 60%) and cellulose fiber (approximately 30%). We attempted simultaneous saccharification and ethanol fermentation of cassava pulp with this arming yeast. During fermentation, ethanol concentration increased as the starch and cellulose fiber substrates contained in the cassava pulp decreased. The results clearly showed that the arming yeast was able to produce ethanol directly from cassava pulp without addition of any hydrolytic enzymes.

Direct ethanol production from cassava pulp using a surface-engineered yeast strain co-displaying two amylases, two cellulases, and {beta}-glucosidase

Energy Technology Data Exchange (ETDEWEB)

Apiwatanapiwat, Waraporn; Rugthaworn, Prapassorn [Japan International Research Center for Agricultural Sciences (JIRCAS), Tsukuba, Ibaraki (Japan). Post-Harvest Science and Technology Div.; Kasetsart Univ., Bangkok (Thailand). Nanotechnology and Biotechnology Div.; Murata, Yoshinori; Kosugi, Akihiko; Arai, Takamitsu; Mori, Yutaka [Japan International Research Center for Agricultural Sciences (JIRCAS), Tsukuba, Ibaraki (Japan). Post-Harvest Science and Technology Div.; Yamada, Ryosuke; Kondo, Akihiko [Kobe Univ. (Japan). Dept. of Chemical Science and Engineering

2011-04-15

In order to develop a method for producing fuel ethanol from cassava pulp using cell surface engineering (arming) technology, an arming yeast co-displaying {alpha}-amylase ({alpha}-AM), glucoamylase, endoglucanase, cellobiohydrase, and {beta}-glucosidase on the surface of the yeast cells was constructed. The novel yeast strain, possessing the activities of all enzymes, was able to produce ethanol directly from soluble starch, barley {beta}-glucan, and acid-treated Avicel. Cassava is a major crop in Southeast Asia and used mainly for starch production. In the starch manufacturing process, large amounts of solid wastes, called cassava pulp, are produced. The major components of cassava pulp are starch (approximately 60%) and cellulose fiber (approximately 30%). We attempted simultaneous saccharification and ethanol fermentation of cassava pulp with this arming yeast. During fermentation, ethanol concentration increased as the starch and cellulose fiber substrates contained in the cassava pulp decreased. The results clearly showed that the arming yeast was able to produce ethanol directly from cassava pulp without addition of any hydrolytic enzymes. (orig.)

Mesta/Kenaf as raw material for Kraft pulping

Energy Technology Data Exchange (ETDEWEB)

Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

1980-03-15

In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

Characteristics and availability of commercially important woods

Science.gov (United States)

Regis B. Miller

1999-01-01

Throughout history, the unique characteristics and comparative abundance of wood have made it a natural material for homes and other structures, furniture, tools, vehicles, and decorative objects. Today, for the same reasons, wood is prized for a multitude of uses. All wood is composed of cellulose, lignin, hemicelluloses, and minor amounts (5% to 10%) of extraneous...

Sequenced anaerobic - aerobic treatment of hemp pulping wastewaters

NARCIS (Netherlands)

Kortekaas, S.

1998-01-01

Biological treatment is an indispensable instrument for water management of non-wood pulp mills, either as internal measure to enable progressive closure of water cycles, or as end of pipe treatment. In this thesis, the sequenced anaerobic-aerobic treatment of hemp ( Cannabis