WorldWideScience

Sample records for weight percent mo

  1. TEM investigation of irradiated U-7 weight percent Mo dispersion fuel

    International Nuclear Information System (INIS)

    Van den Berghe, S.

    2009-01-01

    In the FUTURE experiment, fuel plates containing U-7 weight percent Mo atomized powder were irradiated in the BR2 reactor. At a burn-up of approximately 33 percent 235 U (6.5 percent FIMA or 1.41 10 21 fissions/cm 3 meat), the fuel plates showed an important deformation and the irradiation was stopped. The plates were submitted to detailed PIE at the Laboratory for High and Medium level Activity. The results of these examinations were reported in the scientific report of last year and published in open literature. Since then, the microstructural aspects of the FUTURE fuel were studied in more detail using transmission electron microscopy (TEM), in an attempt to understand the nature of the interaction phase and the fission gas behavior in the atomized U(Mo) fuel. The FUTURE experiment is regarded as the definitive proof that the classical atomized U(Mo) dispersion fuel is not stable under irradiation, at least in the conditions required for normal operation of plate-type fuel. The main cause for the instability was identified to be the irradiation behavior of the U(Mo)-Al interaction phase which is formed between the U(Mo) particles and the pure aluminum matrix during irradiation. It is assumed to become amorphous under irradiation and as such cannot retain the fission gas in stable bubbles. As a consequence, gas filled voids are generated between the interaction layer and the matrix, resulting in fuel plate pillowing and failure. The objective of the TEM investigation was the confirmation of this assumption of the amorphisation of the interaction phase. A deeper understanding of the actual nature of this layer and the fission gas behaviour in these fuels in general can allow a more oriented search for a solution to the fuel failures

  2. Characterization of the uranium--2 weight percent molybdenum alloy

    International Nuclear Information System (INIS)

    Hemperly, V.C.

    1976-01-01

    The uranium-2 wt percent molybdenum alloy was prepared, processed, and age hardened to meet a minimum 930-MPa yield strength (0.2 percent) with a minimum of 10 percent elongation. These mechanical properties were obtained with a carbon level up to 300 ppM in the alloy. The tensile-test ductility is lowered by the humidity of the laboratory atmosphere

  3. MFT homogeneity study at TNX: Final report on the low weight percent solids concentration

    International Nuclear Information System (INIS)

    Jenkins, W.J.

    1993-01-01

    A statistical design and analysis of both elemental analyses and weight percent solids analyses data was utilized to evaluate the MFT homogeneity at low heel levels and low agitator speed at both high and low solids feed concentrations. The homogeneity was also evaluated at both low and high agitator speed at the 6000+ gallons static level. The dynamic level portion of the test simulated feeding the Melter from the MFT to evaluate the uniformity of the solids slurry composition (Frit-PHA-Sludge) entering the melter from the MFT. This final report provides the results and conclusions from the second half of the study, the low weight percent solids concentration portion, as well as a comparison with the results from the first half of the study, the high weight percent solids portion

  4. Examination of temperature-induced shape memory of uranium--5.3-to 6.9 weight percent niobium alloys

    International Nuclear Information System (INIS)

    Hemperly, V.C.

    1976-01-01

    The uranium-niobium alloy system was examined in the range of 5.3-to-6.9 weight percent niobium with respect to shape memory, mechanical properties, metallography, Coefficients of linear thermal expansion, and differential thermal analysis. Shape memory increased with increasing niobium levels in the study range. There were no useful correlations found between shape memory and the other tests. Coefficients of linear thermal expansion tests of as-quenched 5.8 and 6.2 weight percent niobium specimens, but not 5.3 and 6.9 weight percent niobium specimens, had a contraction component on heating, but the phenomenon was not a contributor to shape memory

  5. 40 CFR 63.8055 - How do I comply with a weight percent HAP limit in coating products?

    Science.gov (United States)

    2010-07-01

    ... HAP limit in coating products? 63.8055 Section 63.8055 Protection of Environment ENVIRONMENTAL...: Miscellaneous Coating Manufacturing Alternative Means of Compliance § 63.8055 How do I comply with a weight percent HAP limit in coating products? (a) As an alternative to complying with the requirements in Table 1...

  6. Impact of response criteria (tibia ash weight vs. percent) on phytase relative non phytate phosphorus equivalance.

    Science.gov (United States)

    Li, W; Angel, R; Kim, S-W; Jiménez-Moreno, E; Proszkowiec-Weglarz, M; Plumstead, P W

    2015-09-01

    The current study was conducted to evaluate the impacts of using tibia ash percentage or ash weight as the response criteria on estimated phytase relative equivalence. Straight run broilers were fed treatment (Trt) diets from 7 to 21 d age (6 birds/pen, 8 pens/Trt). The corn-soy based Trt were formulated to contain 0.80% Ca and 4 non-phytate phosphorus (nPP) concentrations (0.20, 0.27, 0.34, and 0.40%). Monocalcium phosphate was the inorganic phosphate source added to achieve 4 different dietary nPP concentrations and against which the nPP relative equivalence of phytase was determined. A 6-phytase (Danisco Animal Nutrition, DuPont Industrial Biosciences, Marlborough, UK) was added at 500 or 1,000 phytase unit ( FTU: )/kg to the 0.20% nPP diet resulting 6 total Trts. Tibia ash was determined at 21 d age. Phytase fed at 500 or 1,000 FTU/kg increased tibia ash weight and ash percentage compared to that of birds fed 0.20% nPP diet without phytase (Pphytase nPP relative equivalence. The R2 obtained from pen value regressions were 0.81 and 0.84, for tibia ash weight and percentage, respectively. Ash percentage from birds fed 500 and 1,000 FTU phytase/kg fell within the range obtained with the MCP additions. Ash weight (842 mg/tibia) from birds fed 1,000 FTU phytase/kg exceeded (Pphytase/kg Trt. The nPP relative equivalence in birds fed 500 FTU phytase/kg were 0.117 and 0.168% based on ash percentage and weight, respectively (Pphytase/kg was 0.166% for ash percentage. Results suggested that ash weight better reflects the amount of bone mineralization as compared to ash percentage and using ash percentage may lead to an underestimation of phytase efficacy. © 2015 Poultry Science Association Inc.

  7. Extrusion of the uranium-0.75 weight percent titanium alloy

    International Nuclear Information System (INIS)

    Jackson, R.J.; Lundberg, M.R.; Boland, J.F.

    1975-01-01

    Procedures are described for extruding the U--0.75 wt percent Ti alloy in the high alpha region (600 to 640 0 C) , and in the upper gamma region (900 to 1000 0 C). The casting of sound extrusion billets has importance in the production of sound extrusions, and procedures are given for casting sound billets up to 1,100 kilograms . Also important in producing sound extrusions is the use of glass lubricants. Reduction ratios of greater than 50 to 1 were achieved on reasonably sized billets. Extrusion constants of 48,000 pounds per square inch (psi) [296 megapascals (MPa)] for alpha phase (630 0 C) and 8,000 psi (56 MPa) for gamma phase (950 0 C) were achieved. Gamma-phase extrusion has preference over alpha-phase extrusion in that larger billets can be used and temperature control is not as critical. However alpha-phase extrusion offers better surface finish, less die wear, and fewer oxidation problems. Billets up to 14 inches in diameter have been successfully gamma-extruded and plans exist for extruding billets up to 20 inches (508 millimetres) in diameter. (U.S.)

  8. Investigation of LMFBR prototype 7A heaters and the metallurgy of the platinum-8 weight percent tungsten alloy

    International Nuclear Information System (INIS)

    Ludwig, R.L.

    1976-09-01

    A Liquid Metal Fast Breeder Reactor 7A prototype heater failure was analyzed. The failure was due to melting of the platinum-8 weight percent tungsten alloy (Pt-8 W) alloy winding caused by a loss of contact with the inside boron nitride insulation. An attempt to simulate a failure revealed that elemental boron forms a low-melting mixture with Pt-8 W, but a means by which boron might be present in an actual heater was not determined. A time/temperature/grain size study of various Pt-8 W alloy samples resulted in behavior which would be expected from a single-phase, solid-solution alloy. The results of the study were useful in estimating the temperatures reached at various locations along the length of two failed 7A prototype heaters

  9. Effect of Mo2C/(Mo2C + WC) weight ratio on the microstructure and mechanical properties of Ti(C,N)-based cermet tool materials

    International Nuclear Information System (INIS)

    Xu, Qingzhong; Zhao, Jun; Ai, Xing; Qin, Wenzhen; Wang, Dawei; Huang, Weimin

    2015-01-01

    To optimize the Mo 2 C content in Ti(C,N)-based cermet tool materials used for cutting the high-strength steel of 42CrMo (AISI 4140/4142 steel), the cermets with different Mo 2 C/(Mo 2 C + WC) weight ratios were prepared. And the microstructure and mechanical properties of cermets were investigated by scanning electron microscope (SEM), X-ray diffraction (XRD) and measurements of transverse rupture strength (TRS), Vickers hardness (HV) and fracture toughness (K IC ). The results indicate that the Mo 2 C/(Mo 2 C + WC) ratios have great influences on the microstructure features and mechanical properties of Ti(C,N)-based cermets. When the Mo 2 C/(Mo 2 C + WC) ratio increases, the Ti(C,N) grains become finer with smaller black cores surrounded by thinner rims, and the structure of cermets tends to be more compact with smaller binder mean free path. Owing to the medium grains and moderate rims, the cermets with a Mo 2 C/(Mo 2 C + WC) ratio of 0.4 exhibit better mechanical properties, and can be chosen as the tool material for machining 42CrMo steel due to the lower Mo content. - Highlights: • Mo 2 C/(Mo 2 C + WC) ratios affect microstructure and mechanical properties of cermets. • Grains become fine and structure of cermets tends to be compact with raised Mo 2 C. • The cermets with a Mo 2 C/(Mo 2 C + WC) ratio of 0.4 can be used to machine 42CrMo steel

  10. Is air-displacement plethysmography a reliable method of detecting ongoing changes in percent body fat within obese children involved in a weight management program?

    DEFF Research Database (Denmark)

    Ewane, Cecile; McConkey, Stacy A; Kreiter, Clarence D

    2010-01-01

    (percent body fat) over time. The gold standard method, hydrodensitometry, has severe limitations for the pediatric population. OBJECTIVE: This study examines the reliability of air-displacement plethysmography (ADP) in detecting percent body fat changes within obese children over time. METHODS: Percent...... body fat by ADP, weight, and body mass index (BMI) were measured for eight obese children aged 5-12 years enrolled in a weight management program over a 12-month period. These measurements were taken at initial evaluation, 1.5 months, 3 months, 6 months, and 12 months to monitor the progress...... of the subjects and detect any changes in these measures over time. Statistical analysis was used to determine the reliability of the data collected. RESULTS: The reliability estimate for percent body fat by ADP was 0.78. This was much lower than the reliability of BMI, 0.98, and weight measurements, 0...

  11. Percent Coverage

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Percent Coverage is a spreadsheet that keeps track of and compares the number of vessels that have departed with and without observers to the numbers of vessels...

  12. Effect of curing methods, packaging and gamma irradiation on the weight loss and dry matter percent of garlic during curing and storage

    International Nuclear Information System (INIS)

    Mahmoud, A.A.; El-Oksh, I.I.; Farag, S.E.A.

    1988-01-01

    The Egyptian garlic plants, showed higher percent of weight loss at 17 or 27 days from curing compared to those of Chinese plants. The curing period of 17 days seemed satisfactory for the Egyptian cultivar, whereas, 27 days seemed to be enough for the Chinese garlic. No significant differences were observed between common and shaded curing methods in weight loss per cent. The Chinese garlic contained higher dry matter percentage than those of the Egyptian cultivar. Shaded cured plants of the two cultivars contained higher dry matter percent than those subjected to the common curing methods. Irradiation of garlic bulbs, shaded curing method and sack packaging decreased, in general the weight loss during storage in comparison with other treatments

  13. [Exclusive breastfeeding in <6mo is associated to a better weight for length in households with food insecurity in Mexico].

    Science.gov (United States)

    González-de Cossío, Teresita; Escobar-Zaragoza, Leticia; González-Castell, Dinorah; Shamah-Levy, Teresa; Rivera-Dommarco, Juan A

    2014-01-01

    To evaluate the effect of exclusive breastfeeding in ENSANUT 2012 (n = 4 022). Breastfeeding indicators from WHO-2008 were calculated. We estimated the effect modifier EBF<6mo of the relationship between FI and weight length (Z W/L) and length for age (Z L/A) Z score. The EBF<6mo was lower in households (hh) with moderate and severe FI than in those with food security (FS) or mild FI hh. Only EBF<6mo infants from hh with moderate and severe FI showed greater Z W/L (0.44) than those without EBF<6mo (p= 0.038, one-tailed). Score Z W/L of infants from hh FS did not vary according to EBF<6mo. EBF<6mo in Mexican infants is associated with better weight for length in households with moderate and severe FI. Breastfeeding promotion, protection and support must be targeted mainly at the most vulnerable, food insecure families.

  14. Effect of Mo{sub 2}C/(Mo{sub 2}C + WC) weight ratio on the microstructure and mechanical properties of Ti(C,N)-based cermet tool materials

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Qingzhong; Zhao, Jun, E-mail: zhaojun@sdu.edu.cn; Ai, Xing; Qin, Wenzhen; Wang, Dawei; Huang, Weimin

    2015-11-15

    To optimize the Mo{sub 2}C content in Ti(C,N)-based cermet tool materials used for cutting the high-strength steel of 42CrMo (AISI 4140/4142 steel), the cermets with different Mo{sub 2}C/(Mo{sub 2}C + WC) weight ratios were prepared. And the microstructure and mechanical properties of cermets were investigated by scanning electron microscope (SEM), X-ray diffraction (XRD) and measurements of transverse rupture strength (TRS), Vickers hardness (HV) and fracture toughness (K{sub IC}). The results indicate that the Mo{sub 2}C/(Mo{sub 2}C + WC) ratios have great influences on the microstructure features and mechanical properties of Ti(C,N)-based cermets. When the Mo{sub 2}C/(Mo{sub 2}C + WC) ratio increases, the Ti(C,N) grains become finer with smaller black cores surrounded by thinner rims, and the structure of cermets tends to be more compact with smaller binder mean free path. Owing to the medium grains and moderate rims, the cermets with a Mo{sub 2}C/(Mo{sub 2}C + WC) ratio of 0.4 exhibit better mechanical properties, and can be chosen as the tool material for machining 42CrMo steel due to the lower Mo content. - Highlights: • Mo{sub 2}C/(Mo{sub 2}C + WC) ratios affect microstructure and mechanical properties of cermets. • Grains become fine and structure of cermets tends to be compact with raised Mo{sub 2}C. • The cermets with a Mo{sub 2}C/(Mo{sub 2}C + WC) ratio of 0.4 can be used to machine 42CrMo steel.

  15. Screening for Cognitive Impairment in Parkinson's Disease: Improving the Diagnostic Utility of the MoCA through Subtest Weighting.

    Directory of Open Access Journals (Sweden)

    Sophie Fengler

    Full Text Available Given the high prevalence of cognitive impairment in Parkinson's disease (PD, cognitive screening is important in clinical practice. The Montreal Cognitive Assessment (MoCA is a frequently used screening test in PD to detect mild cognitive impairment (PD-MCI and Parkinson's disease dementia (PD-D. However, the proportion in which the subtests are represented in the MoCA total score does not seem reasonable. We present the development and preliminary evaluation of an empirically based alternative scoring system of the MoCA which aims at increasing the overall diagnostic accuracy.In study 1, the MoCA was administered to 40 patients with PD without cognitive impairment (PD-N, PD-MCI, or PD-D, as defined by a comprehensive neuropsychological test battery. The new MoCA scoring algorithm was developed by defining Areas under the Curve (AUC for MoCA subtests in a Receiver Operating Characteristic (ROC and by weighting the subtests according to their sensitivities and specificities. In study 2, an independent sample of 24 PD patients (PD-N, PD-MCI, or PD-D was tested with the MoCA. In both studies, diagnostic accuracy of the original and the new scoring procedure was calculated.Diagnostic accuracy increased with the new MoCA scoring algorithm. In study 1, the sensitivity to detect cognitive impairment increased from 62.5% to 92%, while specificity decreased only slightly from 77.7% to 73%; in study 2, sensitivity increased from 68.8% to 81.3%, while specificity stayed stable at 75%.This pilot study demonstrates that the sensitivity of the MoCA can be enhanced substantially by an empirically based weighting procedure and that the proposed scoring algorithm may serve the MoCA's actual purpose as a screening tool in the detection of cognitive dysfunction in PD patients better than the original scoring of the MoCA. Further research with larger sample sizes is necessary to establish efficacy of the alternate scoring system.

  16. EFFECT OF STRESS ON THE PERCENT BODY WEIGHT CHANGE AND MRNA EXPRESSION OF IGF-1, SURVIVINE AND HSP-70 GENE IN THE HIERARCHIAL FOLLICLES OF JAPANESE QUAIL

    Directory of Open Access Journals (Sweden)

    N Shit

    2014-12-01

    Full Text Available The present study was carried out to explore the effect of stress on body weight and the mRNA expression of IGF-1, Survivine and HSP-70 gene in the hierarchial follicles of Japanese quail. A total 24 birds (10 weeks were taken and stress was induced by immobilization daily for 2hrs (between 9.00 - 11.00 AM throughout the study (10 days. Four birds were sacrificed on 1, 2, 4, 6, 8 and 10 days of the treatment. Hierarchial follicles (F1, F2 & F3 were aseptically collected to quantify the expression of IGF-1, Survivine and HSP-70 gene using real-time PCR technique. The percent body weight reduction increased and reached highest (21.30% on 10th day. The fold expression of IGF-1 gene was significantly ((P=0.05 down regulated in advance to the time of experiment. However, the fold expression of survivine gene was significantly (P=0.05 up regulated and the intensity was highest (17 fold in F-3 follicle on 4th day of experiment. No significant change in the mRNA expression of HSP-70 gene was evident in this study. From this study it may be concluded that stress brings physio-molecular change through HPA activation, which not only causes tissue regression also modifies the cellular mechanism.

  17. U-10Mo Sample Preparation and Examination using Optical and Scanning Electron Microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Prabhakaran, Ramprashad [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Joshi, Vineet V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rhodes, Mark A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schemer-Kohrn, Alan L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Guzman, Anthony D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lavender, Curt A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-10-01

    The purpose of this document is to provide guidelines to prepare specimens of uranium alloyed with 10 weight percent molybdenum (U-10Mo) for optical metallography and scanning electron microscopy. This document also provides instructions to set up an optical microscope and a scanning electron microscope to analyze U-10Mo specimens and to obtain the required information.

  18. U-10Mo Sample Preparation and Examination using Optical and Scanning Electron Microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Prabhakaran, Ramprashad [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Joshi, Vineet V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rhodes, Mark A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schemer-Kohrn, Alan L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Guzman, Anthony D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lavender, Curt A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-03-30

    The purpose of this document is to provide guidelines to prepare specimens of uranium alloyed with 10 weight percent molybdenum (U-10Mo) for optical metallography and scanning electron microscopy. This document also provides instructions to set up an optical microscope and a scanning electron microscope to analyze U-10Mo specimens and to obtain the required information.

  19. U-10Mo Sample Preparation and Examination using Optical and Scanning Electron Microscopy. Rev. 1

    International Nuclear Information System (INIS)

    Prabhakaran, Ramprashad; Joshi, Vineet V.; Rhodes, Mark A.; Schemer-Kohrn, Alan L.; Guzman, Anthony D.; Lavender, Curt A.

    2016-01-01

    The purpose of this document is to provide guidelines to prepare specimens of uranium alloyed with 10 weight percent molybdenum (U-10Mo) for optical metallography and scanning electron microscopy. This document also provides instructions to set up an optical microscope and a scanning electron microscope to analyze U-10Mo specimens and to obtain the required information.

  20. Percent Wetland Cover

    Data.gov (United States)

    U.S. Environmental Protection Agency — Wetlands act as filters, removing or diminishing the amount of pollutants that enter surface water. Higher values for percent of wetland cover (WETLNDSPCT) may be...

  1. Percent Wetland Cover (Future)

    Data.gov (United States)

    U.S. Environmental Protection Agency — Wetlands act as filters, removing or diminishing the amount of pollutants that enter surface water. Higher values for percent of wetland cover (WETLNDSPCT) may be...

  2. Adipose tissue transcriptome reflects variations between subjects with continued weight loss and subjects regaining weight 6 mo after caloric restriction independent of energy intake

    DEFF Research Database (Denmark)

    Márquez-Quinõnes, Adriana; Mutch, David M.; Debard, Cyrille

    2010-01-01

    The mechanisms underlying body weight evolution after diet-induced weight loss are poorly understood.......The mechanisms underlying body weight evolution after diet-induced weight loss are poorly understood....

  3. Comparison of midupper arm circumference and weight-for-height z score for assessing acute malnutrition in Bangladeshi children aged 6-60 mo: an analytical study.

    Science.gov (United States)

    Hossain, Md Iqbal; Ahmed, Tahmeed; Arifeen, Shams El; Billah, Sk Masum; Faruque, Asg; Islam, M Munirul; Jackson, Alan A

    2017-11-01

    Background : In clinical settings, wasting in childhood has primarily been assessed with the use of a weight-for-height z score (WHZ), and in community settings, it has been assessed via the midupper arm circumference (MUAC) with a cutoff children were not identified when these cutoffs for MUAC were used. Objective: We determined the cutoffs for MUAC to detect wasting in Bangladeshi children aged 6-60 mo. Design: A secondary analysis was carried out on data from 27,767 children aged 6-59 mo. This analysis comprised 1 ) 9131 children across Bangladesh and 2 ) 18,636 children enrolled in a surveillance study in the Dhaka Hospital of icddr,b during 1996-2014. The area under the receiver operating curve was used to indicate the most appropriate choice for cutoffs that related MUAC with WHZ. Results: The mean ± SD age for the entire group was 21 ± 14 mo, WHZ was -1.18 ± 1.23, height-for-age z score was -1.63 ± 1.39, MUAC was 136 ± 14 mm, and 45% of subjects were girls. MUAC correlated with the WHZ ( r : 0.618, P < 0.001). Age-stratified analyses revealed that, for ages 6-24 mo, MUAC cutoffs were <120 mm for a WHZ <-3 and <125 mm for a WHZ <-2 with a sensitivity of 72.9% and 63.2%, respectively, and a specificity of 84.7% and 85.3%, respectively; for ages 25-36 mo, MUAC cutoffs were <125 mm for a WHZ <-3 and <135 mm for a WHZ <-2 with a sensitivity of 55.0% and 71.7%, respectively, and a specificity of 92.8% and 78.7% respectively; and for ages 37-60 mo, MUAC cutoffs were <135 mm for a WHZ <-3 and <140 mm for a WHZ <-2 with a sensitivity of 71.4% and 70.4%, respectively, and a specificity of 84.6% and 80.3%, respectively. Conclusion: The respective cutoffs for MUAC to better capture the vulnerability and risk of severe (WHZ <-3) and moderate (WHZ <-2) wasting would be <120 and <125 mm for ages 6-24 mo, <125 and <135 mm for ages 25-36 mo, and <135 and <140 mm for ages 37-60 mo. © 2017 American Society for Nutrition.

  4. A distinct adipose tissue gene expression response to caloric restriction predicts 6-mo weight maintenance in obese subjects

    DEFF Research Database (Denmark)

    Mutch, D. M.; Pers, Tune Hannes; Temanni, M. R.

    2011-01-01

    Background: Weight loss has been shown to reduce risk factors associated with cardiovascular disease and diabetes; however, successful maintenance of weight loss continues to pose a challenge. Objective: The present study was designed to assess whether changes in subcutaneous adipose tissue (scAT......-term weight maintenance. This trial was registered at clinicaltrials.gov as NCT00390637. ©American Society for Nutrition. All rights reserved....

  5. MO-DE-207A-01: Impact of Statistical Weights On Detection of Low-Contrast Details in Model-Based Iterative CT Reconstruction

    International Nuclear Information System (INIS)

    Noo, F; Guo, Z

    2016-01-01

    Purpose: Penalized-weighted least-square reconstruction has become an important research topic in CT, to reduce dose without affecting image quality. Two components impact image quality in this reconstruction: the statistical weights and the use of an edge-preserving penalty term. We are interested in assessing the influence of statistical weights on their own, without the edge-preserving feature. Methods: The influence of statistical weights on image quality was assessed in terms of low-contrast detail detection using LROC analysis. The task amounted to detect and localize a 6-mm lesion with random contrast inside the FORBILD head phantom. A two-alternative forced-choice experiment was used with two human observers performing the task. Reconstructions without and with statistical weights were compared, both using the same quadratic penalty term. The beam energy was set to 30keV to amplify spatial differences in attenuation and thereby the role of statistical weights. A fan-beam data acquisition geometry was used. Results: Visual inspection of images clearly showed a difference in noise between the two reconstructions methods. As expected, the reconstruction without statistical weights exhibited noise streaks. The other reconstruction appeared better in this aspect, but presented other disturbing noise patterns and artifacts induced by the weights. The LROC analysis yield the following 95-percent confidence interval for the difference in reader-averaged AUC (reconstruction without weights minus reconstruction with weights): [0.0026,0.0599]. The mean AUC value was 0.9094. Conclusion: We have investigated the impact of statistical weights without the use of edge-preserving penalty in penalized weighted least-square reconstruction. A decrease rather than increase in image quality was observed when using statistical weights. Thus, the observers were better able to cope with the noise streaks than the noise patterns and artifacts induced by the statistical weights. It

  6. MO-DE-207A-01: Impact of Statistical Weights On Detection of Low-Contrast Details in Model-Based Iterative CT Reconstruction

    Energy Technology Data Exchange (ETDEWEB)

    Noo, F; Guo, Z [University of Utah, Salt Lake City, UT (United States)

    2016-06-15

    Purpose: Penalized-weighted least-square reconstruction has become an important research topic in CT, to reduce dose without affecting image quality. Two components impact image quality in this reconstruction: the statistical weights and the use of an edge-preserving penalty term. We are interested in assessing the influence of statistical weights on their own, without the edge-preserving feature. Methods: The influence of statistical weights on image quality was assessed in terms of low-contrast detail detection using LROC analysis. The task amounted to detect and localize a 6-mm lesion with random contrast inside the FORBILD head phantom. A two-alternative forced-choice experiment was used with two human observers performing the task. Reconstructions without and with statistical weights were compared, both using the same quadratic penalty term. The beam energy was set to 30keV to amplify spatial differences in attenuation and thereby the role of statistical weights. A fan-beam data acquisition geometry was used. Results: Visual inspection of images clearly showed a difference in noise between the two reconstructions methods. As expected, the reconstruction without statistical weights exhibited noise streaks. The other reconstruction appeared better in this aspect, but presented other disturbing noise patterns and artifacts induced by the weights. The LROC analysis yield the following 95-percent confidence interval for the difference in reader-averaged AUC (reconstruction without weights minus reconstruction with weights): [0.0026,0.0599]. The mean AUC value was 0.9094. Conclusion: We have investigated the impact of statistical weights without the use of edge-preserving penalty in penalized weighted least-square reconstruction. A decrease rather than increase in image quality was observed when using statistical weights. Thus, the observers were better able to cope with the noise streaks than the noise patterns and artifacts induced by the statistical weights. It

  7. Dietary benzo(a)pyrene intake during pregnancy and birth weight: associations modified by vitamin C intakes in the Norwegian Mother and Child Cohort Study (MoBa).

    Science.gov (United States)

    Duarte-Salles, Talita; Mendez, Michelle A; Meltzer, Helle Margrete; Alexander, Jan; Haugen, Margaretha

    2013-10-01

    Maternal exposure to polycyclic aromatic hydrocarbons (PAH) during pregnancy has been associated with reduced fetal growth. However, the role of diet, the main source of PAH exposure among non-smokers, remains uncertain. To assess associations between maternal exposure to dietary intake of the genotoxic PAH benzo(a)pyrene [B(a)P] during pregnancy and birth weight, exploring potential effect modification by dietary intakes of vitamins C, E and A, hypothesized to influence PAH metabolism. This study included 50,651 women in the Norwegian Mother and Child Cohort Study (MoBa). Dietary B(a)P and nutrient intakes were estimated based on total consumption obtained from a food frequency questionnaire (FFQ) and estimated based on food composition data. Data on infant birth weight were obtained from the Medical Birth Registry of Norway (MBRN). Multivariate regression was used to assess associations between dietary B(a)P and birth weight, evaluating potential interactions with candidate nutrients. The multivariate-adjusted coefficient (95%CI) for birth weight associated with maternal energy-adjusted B(a)P intake was -20.5g (-31.1, -10.0) in women in the third compared with the first tertile of B(a)P intake. Results were similar after excluding smokers. Significant interactions were found between elevated intakes of vitamin C (>85mg/day) and dietary B(a)P during pregnancy for birth weight (P<0.05), but no interactions were found with other vitamins. The multivariate-adjusted coefficients (95%CI) for birth weight in women in the third compared with the first tertile of B(a)P intake were -44.4g (-76.5, -12.3) in the group with low vitamin C intakes vs. -17.6g (-29.0, -6.1) in the high vitamin C intake group. The results suggest that higher prenatal exposure to dietary B(a)P may reduce birth weight. Lowering maternal intake of B(a)P and increasing dietary vitamin C intake during pregnancy may help to reduce any adverse effects of B(a)P on birth weight. © 2013.

  8. Inspiration: One Percent and Rising

    Science.gov (United States)

    Walling, Donovan R.

    2009-01-01

    Inventor Thomas Edison once famously declared, "Genius is one percent inspiration and ninety-nine percent perspiration." If that's the case, then the students the author witnessed at the International Student Media Festival (ISMF) last November in Orlando, Florida, are geniuses and more. The students in the ISMF pre-conference workshop…

  9. Comparison of 3 ad libitum diets for weight-loss maintenance, risk of cardiovascular disease, and diabetes: A 6-mo randomized, controlled trial

    DEFF Research Database (Denmark)

    Due, Anette; Larsen, Thomas M; Mu, Huiling

    2008-01-01

    BACKGROUND: The optimal dietary content and type of fat and carbohydrate for weight management has been debated for decades. OBJECTIVE: The objective was to compare the effects of 3 ad libitum diets on the maintenance of an initial weight loss of >or=8% and risk factors for CVD and diabetes during...... a 6-mo controlled dietary intervention. DESIGN: Nondiabetic overweight or obese [mean +/- SD body mass index (in kg/m(2)): 31.5 +/- 2.6] men (n = 55) and women (n = 76) aged 28.2 +/- 4.8 y were randomly assigned to a diet providing a moderate amount of fat (35-45% of energy) and >20% of fat...... as monounsaturated fatty acids (MUFA diet; n = 54), to a low-fat (20-30% of energy) diet (LF diet; n = 51), or to a control diet (35% of energy as fat; n = 26). Protein constituted 10-20% of energy in all 3 diets. All foods were provided free of charge from a purpose-built supermarket. RESULTS: More subjects dropped...

  10. Effect of Caffeine Co-Ingested with Carnitine on Weight, Body-Fat Percent, Serum Leptin and Lipid Profile Changes in Male Teen Soccer Players: a Randomized Clinical Trial

    Directory of Open Access Journals (Sweden)

    Saeed Shirali

    2016-10-01

    Full Text Available Background: Weight loss and decreasing the Body fat percentage (BF% is motivated to optimize performance. In order to achieve these, many supplements are used by athletes, however the possible negative or synergic effects have not been fully described in the literature, specifically in humans. The present study was conducted to investigate the co-administration effects of two common used supplements in body weight and BF% management to recommend athletes for safe weight and BF% reduction. Materials and Methods: In the present double-blind, randomized, parallel, placebo-controlled study, the effect of six-week co-administration of caffeine and carnitine was determined on changes in body weight (BW, BF%, serum leptin concentration and lipid profile (triglyceride, HDL Cholesterol, LDL Cholesterol and Total Cholesterol, fasting blood glucose (FBG, and free fatty acid (FFA changes. Twenty eight male teen soccer players  from Ahvaz-Iran, were divided in three groups (group CafPlc, caffeine (6 mg/kg/day + dextrose; group CafCar, caffeine (6 mg/kg/day + carnitine (2g; and group Plc, dextrose. Results: Caffeine-carnitine had a lowering effect on BW (P=0.02 and BF% (P=0.03, compared to caffeine alone and placebo in male teen soccer players (mean age of 16.92 ± 0.76 years. TG was significantly decreased in CafCar (P=0.04. FFA levels were increased in CafCar (P=0.04 and there was significant differences between CafCar and Plc groups (P=0.01. FBG was increased in both CafPlc and CafCar (P=0.01 and P=0.02, respectively, with no significant differences between groups. Conclusion: The synergistic effect of caffeine-carnitine might be suggested to decrease the BF% and BW, besides it may prevent the increment of FFA levels; however it should be prescribed cautiously since it increased FBG levels.

  11. Theoretical Model for Volume Fraction of UC, 235U Enrichment, and Effective Density of Final U 10Mo Alloy

    Energy Technology Data Exchange (ETDEWEB)

    Devaraj, Arun [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab. (EMSL); Prabhakaran, Ramprashad [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab. (EMSL); Joshi, Vineet V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab. (EMSL); Hu, Shenyang Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab. (EMSL); McGarrah, Eric J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab. (EMSL); Lavender, Curt A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab. (EMSL)

    2016-04-12

    The purpose of this document is to provide a theoretical framework for (1) estimating uranium carbide (UC) volume fraction in a final alloy of uranium with 10 weight percent molybdenum (U-10Mo) as a function of final alloy carbon concentration, and (2) estimating effective 235U enrichment in the U-10Mo matrix after accounting for loss of 235U in forming UC. This report will also serve as a theoretical baseline for effective density of as-cast low-enriched U-10Mo alloy. Therefore, this report will serve as the baseline for quality control of final alloy carbon content

  12. Microstructure and properties of MoSi2-MoB and MoSi2-Mo5Si3 molybdenum silicides

    International Nuclear Information System (INIS)

    Schneibel, J.H.; Sekhar, J.A.

    2003-01-01

    MoSi 2 -based intermetallics containing different volume fractions of MoB or Mo 5 Si 3 were fabricated by hot-pressing MoSi 2 , MoB, and Mo 5 Si 3 powders in vacuum. Both classes of alloys contained approximately 5 vol.% of dispersed silica phase. Additions of MoB or Mo 5 Si 3 caused the average grain size to decrease. The decrease in the grain size was typically accompanied by an increase in flexure strength, a decrease in the room temperature fracture toughness, and a decrease in the hot strength (compressive creep strength) measured around 1200 deg. C, except when the Mo 5 Si 3 effectively became the major phase. Oxidation measurements on the two classes of alloys were carried out in air. Both classes of alloys were protected from oxidation by an in-situ adherent scale that formed on exposure to high temperature. The scale, although not analyzed in detail, is commonly recognized in MoSi 2 containing materials as consisting mostly of SiO 2 . The MoB containing materials showed an increase in the scale thickness and the cyclic oxidation rate at 1400 deg. C when compared with pure MoSi 2 . However, in contrast with the pure MoSi 2 material, oxidation at 1400 deg. C began with a weight loss followed by a weight gain and the formation of the protective silica layer. The Mo 5 Si 3 containing materials experienced substantial initial weight losses followed by regions of small weight changes. Overall, the MoB and Mo 5 Si 3 additions to MoSi 2 tended to be detrimental for the mechanical and oxidative properties

  13. Improved Mo-Re VPS Alloys for High-Temperature Uses

    Science.gov (United States)

    Hickman, Robert; Martin, James; McKechnie, Timothy; O'Dell, John Scott

    2011-01-01

    Dispersion-strengthened molybdenum- rhenium alloys for vacuum plasma spraying (VPS) fabrication of high-temperature-resistant components are undergoing development. In comparison with otherwise equivalent non-dispersion-strengthened Mo-Re alloys, these alloys have improved high-temperature properties. Examples of VPS-fabricated high-temperature-resistant components for which these alloys are expected to be suitable include parts of aircraft and spacecraft engines, furnaces, and nuclear power plants; wear coatings; sputtering targets; x-ray targets; heat pipes in which liquid metals are used as working fluids; and heat exchangers in general. These alloys could also be useful as coating materials in some biomedical applications. The alloys consist of 60 weight percent Mo with 40 weight percent Re made from (1) blends of elemental Mo and Re powders or (2) Re-coated Mo particles that have been subjected to a proprietary powder-alloying-and-spheroidization process. For most of the dispersion- strengthening experiments performed thus far in this development effort, 0.4 volume percent of transition-metal ceramic dispersoids were mixed into the feedstock powders. For one experiment, the proportion of dispersoid was 1 volume percent. In each case, the dispersoid consisted of either ZrN particles having sizes <45 m, ZrO2 particles having sizes of about 1 m, HfO2 particles having sizes <45 m, or HfN particles having sizes <1 m. These materials were chosen for evaluation on the basis of previously published thermodynamic stability data. For comparison, Mo-Re feedstock powders without dispersoids were also prepared.

  14. The Algebra of the Cumulative Percent Operation.

    Science.gov (United States)

    Berry, Andrew J.

    2002-01-01

    Discusses how to help students avoid some pervasive reasoning errors in solving cumulative percent problems. Discusses the meaning of ."%+b%." the additive inverse of ."%." and other useful applications. Emphasizes the operational aspect of the cumulative percent concept. (KHR)

  15. A Conceptual Model for Solving Percent Problems.

    Science.gov (United States)

    Bennett, Albert B., Jr.; Nelson, L. Ted

    1994-01-01

    Presents an alternative method to teaching percent problems which uses a 10x10 grid to help students visualize percents. Offers a means of representing information and suggests different approaches for finding solutions. Includes reproducible student worksheet. (MKR)

  16. Predicting successful long-term weight loss from short-term weight-loss outcomes: new insights from a dynamic energy balance model (the POUNDS Lost study).

    Science.gov (United States)

    Thomas, Diana M; Ivanescu, Andrada E; Martin, Corby K; Heymsfield, Steven B; Marshall, Kaitlyn; Bodrato, Victoria E; Williamson, Donald A; Anton, Stephen D; Sacks, Frank M; Ryan, Donna; Bray, George A

    2015-03-01

    Currently, early weight-loss predictions of long-term weight-loss success rely on fixed percent-weight-loss thresholds. The objective was to develop thresholds during the first 3 mo of intervention that include the influence of age, sex, baseline weight, percent weight loss, and deviations from expected weight to predict whether a participant is likely to lose 5% or more body weight by year 1. Data consisting of month 1, 2, 3, and 12 treatment weights were obtained from the 2-y Preventing Obesity Using Novel Dietary Strategies (POUNDS Lost) intervention. Logistic regression models that included covariates of age, height, sex, baseline weight, target energy intake, percent weight loss, and deviation of actual weight from expected were developed for months 1, 2, and 3 that predicted the probability of losing model. The AUC statistic quantified the ROC curve's capacity to classify participants likely to lose models yielding the highest AUC were retained as optimal. For comparison with current practice, ROC curves relying solely on percent weight loss were also calculated. Optimal models for months 1, 2, and 3 yielded ROC curves with AUCs of 0.68 (95% CI: 0.63, 0.74), 0.75 (95% CI: 0.71, 0.81), and 0.79 (95% CI: 0.74, 0.84), respectively. Percent weight loss alone was not better at identifying true positives than random chance (AUC ≤0.50). The newly derived models provide a personalized prediction of long-term success from early weight-loss variables. The predictions improve on existing fixed percent-weight-loss thresholds. Future research is needed to explore model application for informing treatment approaches during early intervention. © 2015 American Society for Nutrition.

  17. Beyond Marbles: Percent Change and Social Justice

    Science.gov (United States)

    Denny, Flannery

    2013-01-01

    In the author's eighth year of teaching, she hit a wall teaching percent change. Percent change is one of the few calculations taught in math classes that shows up regularly in the media, and one that she often does in her head to make sense of the world around her. Despite this, she had been teaching percent change using textbook problems about…

  18. Adherence to the New Nordic Diet during pregnancy and subsequent maternal weight development: a study conducted in the Norwegian Mother and Child Cohort Study (MoBa).

    Science.gov (United States)

    Skreden, Marianne; Hillesund, Elisabet R; Wills, Andrew K; Brantsæter, Anne Lise; Bere, Elling; Øverby, Nina C

    2018-06-01

    The rising prevalence of overweight and obesity is a worldwide public health challenge. Pregnancy and beyond is a potentially important window for future weight gain in women. We investigated associations between maternal adherence to the New Nordic diet (NND) during pregnancy and maternal BMI trajectories from delivery to 8 years post delivery. Data are from the Norwegian Mother and Child Cohort. Pregnant women from all of Norway were recruited between 1999 and 2008, and 55 056 are included in the present analysis. A previously constructed diet score, NND, was used to assess adherence to the diet. The score favours intake of Nordic fruits, root vegetables, cabbages, potatoes, oatmeal porridge, whole grains, wild fish, game, berries, milk and water. Linear spline multi-level models were used to estimate the association. We found that women with higher adherence to the NND pattern during pregnancy had on average lower post-partum BMI trajectories and slightly less weight gain up to 8 years post delivery compared with the lower NND adherers. These associations remained after adjustment for physical activity, education, maternal age, smoking and parity (mean diff at delivery (high v. low adherers): -0·3 kg/m2; 95 % CI -0·4, -0·2; mean diff at 8 years: -0·5 kg/m2; 95 % CI -0·6, -0·4), and were not explained by differences in energy intake or by exclusive breast-feeding duration. Similar patterns of associations were seen with trajectories of overweight/obesity as the outcome. In conclusion, our findings suggest that the NND may have beneficial properties to long-term weight regulation among women post-partum.

  19. MO-DE-207A-10: One-Step CT Reconstruction for Metal Artifact Reduction by a Modification of Penalized Weighted Least-Squares (PWLS)

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H; Chen, J [University of California San Francisco, San Francisco, CA (United States)

    2016-06-15

    Purpose: Metal objects create severe artifacts in kilo-voltage (kV) CT image reconstructions due to the high attenuation coefficients of high atomic number objects. Most of the techniques devised to reduce this artifact utilize a two-step approach, which do not reliably yield the qualified reconstructed images. Thus, for accuracy and simplicity, this work presents a one-step reconstruction method based on a modified penalized weighted least-squares (PWLS) technique. Methods: Existing techniques for metal artifact reduction mostly adopt a two-step approach, which conduct additional reconstruction with the modified projection data from the initial reconstruction. This procedure does not consistently perform well due to the uncertainties in manipulating the metal-contaminated projection data by thresholding and linear interpolation. This study proposes a one-step reconstruction process using a new PWLS operation with total-variation (TV) minimization, while not manipulating the projection. The PWLS for CT reconstruction has been investigated using a pre-defined weight, based on the variance of the projection datum at each detector bin. It works well when reconstructing CT images from metal-free projection data, which does not appropriately penalize metal-contaminated projection data. The proposed work defines the weight at each projection element under the assumption of a Poisson random variable. This small modification using element-wise penalization has a large impact in reducing metal artifacts. For evaluation, the proposed technique was assessed with two noisy, metal-contaminated digital phantoms, against the existing PWLS with TV minimization and the two-step approach. Result: The proposed PWLS with TV minimization greatly improved the metal artifact reduction, relative to the other techniques, by watching the results. Numerically, the new approach lowered the normalized root-mean-square error about 30 and 60% for the two cases, respectively, compared to the two

  20. An evaluation of 10 percent and 20 percent benzocaine gels in patients with acute toothaches

    Science.gov (United States)

    Hersh, Elliot V.; Ciancio, Sebastian G.; Kuperstein, Arthur S.; Stoopler, Eric T.; Moore, Paul A.; Boynes, Sean G.; Levine, Steven C.; Casamassimo, Paul; Leyva, Rina; Mathew, Tanya; Shibly, Othman; Creighton, Paul; Jeffers, Gary E.; Corby, Patricia M.A.; Turetzky, Stanley N.; Papas, Athena; Wallen, Jillian; Idzik-Starr, Cynthia; Gordon, Sharon M.

    2013-01-01

    Background The authors evaluated the efficacy and tolerability of 10 percent and 20 percent benzocaine gels compared with those of a vehicle (placebo) gel for the temporary relief of toothache pain. They also assessed the compliance with the label dose administration directions on the part of participants with toothache pain. Methods Under double-masked conditions, 576 participants self-applied study gel to an open tooth cavity and surrounding oral tissues. Participants evaluated their pain intensity and pain relief for 120 minutes. The authors determined the amount of gel the participants applied. Results The responders’ rates (the primary efficacy parameter), defined as the percentage of participants who had an improvement in pain intensity as exhibited by a pain score reduction of at least one unit on the dental pain scale from baseline for two consecutive assessments any time between the five- and 20-minute points, were 87.3 percent, 80.7 percent and 70.4 percent, respectively, for 20 percent benzocaine gel, 10 percent benzocaine gel and vehicle gel. Both benzocaine gels were significantly (P ≤ .05) better than vehicle gel; the 20 percent benzocaine gel also was significantly (P ≤ .05) better than the 10 percent benzocaine gel. The mean amount of gel applied was 235.6 milligrams, with 88.2 percent of participants applying 400 mg or less. Conclusions Both 10 percent and 20 percent benzocaine gels were more efficacious than the vehicle gel, and the 20 percent benzocaine gel was more efficacious than the 10 percent benzocaine gel. All treatments were well tolerated by participants. Practical Implications Patients can use 10 percent and 20 percent benzocaine gels to temporarily treat toothache pain safely. PMID:23633700

  1. Oxidation and creep behavior of Mo*5*Si*3* based materials

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Mitch [Iowa State Univ., Ames, IA (United States)

    1995-06-19

    Mo5Si3 shows promise as a high temperature creep resistant material. The high temperature oxidation resistance of Mo5Si3 has been found to be poor, however, limiting its use in oxidizing atmospheres. Undoped Mo5Si3 exhibits mass loss in the temperature range 800°-1200°C due to volatilization of molybdenum oxide, indicating that the silica scale does not provide a passivating layer. The addition of boron results in protective scale formation and parabolic oxidation kinetics in the temperature range of 1050{degrees}-1300°C. The oxidation rate of Mo5Si3 was decreased by 5 orders of magnitude at 1200°C by doping with less than two weight percent boron. Boron doping eliminates catastrophic "pest" oxidation at 800°C. The mechanism for improved oxidation resistance of boron doped Mo5Si3 is due to scale modification by boron.

  2. Serum Predictors of Percent Lean Mass in Young Adults.

    Science.gov (United States)

    Lustgarten, Michael S; Price, Lori L; Phillips, Edward M; Kirn, Dylan R; Mills, John; Fielding, Roger A

    2016-08-01

    Lustgarten, MS, Price, LL, Phillips, EM, Kirn, DR, Mills, J, and Fielding, RA. Serum predictors of percent lean mass in young adults. J Strength Cond Res 30(8): 2194-2201, 2016-Elevated lean (skeletal muscle) mass is associated with increased muscle strength and anaerobic exercise performance, whereas low levels of lean mass are associated with insulin resistance and sarcopenia. Therefore, studies aimed at obtaining an improved understanding of mechanisms related to the quantity of lean mass are of interest. Percent lean mass (total lean mass/body weight × 100) in 77 young subjects (18-35 years) was measured with dual-energy x-ray absorptiometry. Twenty analytes and 296 metabolites were evaluated with the use of the standard chemistry screen and mass spectrometry-based metabolomic profiling, respectively. Sex-adjusted multivariable linear regression was used to determine serum analytes and metabolites significantly (p ≤ 0.05 and q ≤ 0.30) associated with the percent lean mass. Two enzymes (alkaline phosphatase and serum glutamate oxaloacetate aminotransferase) and 29 metabolites were found to be significantly associated with the percent lean mass, including metabolites related to microbial metabolism, uremia, inflammation, oxidative stress, branched-chain amino acid metabolism, insulin sensitivity, glycerolipid metabolism, and xenobiotics. Use of sex-adjusted stepwise regression to obtain a final covariate predictor model identified the combination of 5 analytes and metabolites as overall predictors of the percent lean mass (model R = 82.5%). Collectively, these data suggest that a complex interplay of various metabolic processes underlies the maintenance of lean mass in young healthy adults.

  3. Neutronic feasibility studies using U-Mo dispersion fuel (9 Wt % Mo, 5.0 gU/cm3) for LEU conversion of the MARIA (Poland), IR-8 (Russia), and WWR-SM (Uzbekistan) research reactors

    International Nuclear Information System (INIS)

    Bretscher, M.M.; Deen, J.R.; Hanan, N.A.; Matos, E.

    2000-01-01

    U-Mo alloys dispersed in an Al matrix offer the potential for high-density uranium fuels needed for the LEU conversion of many research reactors. On-going fuel qualification tests by the US RERTR Program show good irradiation properties of U-Mo alloy dispersion fuel containing 7-10 weight percent molybdenum. For the neutronic studies in this paper the alloy was assumed to contain 9 wt % Mo (U-9Mo) with a uranium density in the fuel meat of 5.00 gU/cm 3 which corresponds to 32.5 volume % U-9Mo. Fuels containing U-9Mo have been used in Russian reactors since the 1950's. For the three research reactors analyzed here, LEU fuel element thicknesses are the same as those for the Russian-fabricated HEU reference fuel elements. Relative to the reference fuels containing 80-90% enriched uranium, LEU U-9Mo Al-dispersion fuel with 5.00 gU/cm 3 doubles the cycle length of the MARIA reactor and increases the IR-8 cycle length by about 11%. For the WWR-SM reactor, the cycle length, and thus the number of fuel assemblies used per year, is nearly unchanged. To match the cycle length of the 36% enriched fuel currently used in the WWR-SM reactor will require a uranium density in the LEU U-9Mo Al-dispersion fuel of about 5.4 gU/cm 3 . The 5.00 gU/cm 3 LEU fuel causes thermal neutron fluxes in water holes near the edge of the core to decrease by (6-8)% for all three reactors. (author)

  4. Predicting successful long-term weight loss from short-term weight-loss outcomes: new insights from a dynamic energy balance model (the POUNDS Lost study)123

    Science.gov (United States)

    Ivanescu, Andrada E; Martin, Corby K; Heymsfield, Steven B; Marshall, Kaitlyn; Bodrato, Victoria E; Williamson, Donald A; Anton, Stephen D; Sacks, Frank M; Ryan, Donna; Bray, George A

    2015-01-01

    Background: Currently, early weight-loss predictions of long-term weight-loss success rely on fixed percent-weight-loss thresholds. Objective: The objective was to develop thresholds during the first 3 mo of intervention that include the influence of age, sex, baseline weight, percent weight loss, and deviations from expected weight to predict whether a participant is likely to lose 5% or more body weight by year 1. Design: Data consisting of month 1, 2, 3, and 12 treatment weights were obtained from the 2-y Preventing Obesity Using Novel Dietary Strategies (POUNDS Lost) intervention. Logistic regression models that included covariates of age, height, sex, baseline weight, target energy intake, percent weight loss, and deviation of actual weight from expected were developed for months 1, 2, and 3 that predicted the probability of losing <5% of body weight in 1 y. Receiver operating characteristic (ROC) curves, area under the curve (AUC), and thresholds were calculated for each model. The AUC statistic quantified the ROC curve’s capacity to classify participants likely to lose <5% of their body weight at the end of 1 y. The models yielding the highest AUC were retained as optimal. For comparison with current practice, ROC curves relying solely on percent weight loss were also calculated. Results: Optimal models for months 1, 2, and 3 yielded ROC curves with AUCs of 0.68 (95% CI: 0.63, 0.74), 0.75 (95% CI: 0.71, 0.81), and 0.79 (95% CI: 0.74, 0.84), respectively. Percent weight loss alone was not better at identifying true positives than random chance (AUC ≤0.50). Conclusions: The newly derived models provide a personalized prediction of long-term success from early weight-loss variables. The predictions improve on existing fixed percent-weight-loss thresholds. Future research is needed to explore model application for informing treatment approaches during early intervention. The POUNDS Lost study was registered at clinicaltrials.gov as NCT00072995. PMID:25733628

  5. How I Love My 80 Percenters

    Science.gov (United States)

    Maturo, Anthony J.

    2002-01-01

    Don't ever take your support staff for granted. By support staff, I mean the people in personnel, logistics, and finance; the ones who can make things happen with a phone call or a signature, or by the same token frustrate you to no end by their inaction; these are people you must depend on. I've spent a lot of time thinking about how to cultivate relationships with my support staff that work to the advantage of both of us. The most important thing that have learned working with people, any people--and I will tell you how I learned this in a minute--is there are some folks you just can't motivate, so forget it, don't try; others you certainly can with a little psychology and some effort; and the best of the bunch, what I call the 80 percenters, you don't need to motivate because they're already on the team and performing beautifully. The ones you can't change are rocks. Face up to it, and just kick them out of your way. I have a reputation with the people who don't want to perform or be part of the team. They don't come near me. If someone's a rock, I pick up on it right away, and I will walk around him or her to find someone better. The ones who can be motivated I take time to nurture. I consider them my projects. A lot of times these wannabes are people who want to help but don't know how. Listen, you can work with them. Lots of people in organizations have the mindset that all that matters are the regulations. God forbid if you ever work outside those regulations. They've got one foot on that regulation and they're holding it tight like a baby holds a blanket. What you're looking for is that first sign that their minds are opening. Usually you hear it in their vocabulary. What used to sound like "We can't do that ... the regulations won't allow it ... we have never done this before," well, suddenly that changes to "We have options ... let's take a look at the options ... let me research this and get back to you." The 80 percenters you want to nurture too, but

  6. Phase equilibria in the CdMoO4-Gd2(MoO4)3 system

    International Nuclear Information System (INIS)

    Tunik, T.A.; Fedorov, N.F.; Razumovskij, S.N.

    1980-01-01

    The constitutional diagram of the CdMoO 4 -Cd 2 (MoO 4 ) 3 system has been plotted using statistical and dynamic methods as well as a complex of instrumental analysis procedures. Three major phases have been found to occur in the systems, viz.: CdMoO 4 based solid solutions that crystallize in the range from 0 to 25 mol.percent of Cd 2 (MoO 4 ) 3 and pass in transit the two-phase narrow region becoming then solid solutions having a distorted scheelite structure and existing in concentrations from 40 to 65 mol.% of Cd 2 (MoO 4 ) 3 . The entire range, in which the Cd 2 (MoO 4 ) 3 solid solutions can exist, amounts to less than 5 mol.%. Certain crystallochemical constants of the phases that occur in the system have been determined [ru

  7. Effects of protein intake and gender on body composition changes: a randomized clinical weight loss trial

    Directory of Open Access Journals (Sweden)

    Evans Ellen M

    2012-06-01

    Full Text Available Abstract Limited data on sex differences in body composition changes in response to higher protein diets (PRO compared to higher carbohydrate diets (CARB suggest that a PRO diet helps preserve lean mass (LM in women more so than in men. Objective To compare male and female body composition responses to weight loss diets differing in macronutrient content. Design Twelve month randomized clinical trial with 4mo of weight loss and 8mo weight maintenance. Subjects Overweight (N = 130; 58 male (M, 72 female (F; BMI = 32.5 ± 0.5 kg/m2 middle-aged subjects were randomized to energy-restricted (deficit ~500 kcal/d diets providing protein at 1.6 g.kg-1.d-1 (PRO or 0.8 g.kg-1.d-1 (CARB. LM and fat mass (FM were measured using dual X-ray absorptiometry. Body composition outcomes were tested in a repeated measures ANOVA controlling for sex, diet, time and their two- and three-way interactions at 0, 4, 8 and 12mo. Results When expressed as percent change from baseline, males and females lost similar amounts of weight at 12mo (M:-11.2 ± 7.1 %, F:-9.9 ± 6.0 %, as did diet groups (PRO:-10.7 ± 6.8 %, CARB:-10.1 ± 6.2 %, with no interaction of gender and diet. A similar pattern emerged for fat mass and lean mass, however percent body fat was significantly influenced by both gender (M:-18.0 ± 12.8 %, F:-7.3 ± 8.1 %, p  Conclusion PRO was more effective in reducing percent body fat vs. CARB over 12mo weight loss and maintenance. Men lost percent total body fat and trunk fat more effectively than women. No interactive effects of protein intake and gender are evident.

  8. Completion of the first approach to critical for the seven percent critical experiment

    International Nuclear Information System (INIS)

    Barber, A. D.; Harms, G. A.

    2009-01-01

    The first approach-to-critical experiment in the Seven Percent Critical Experiment series was recently completed at Sandia. This experiment is part of the Seven Percent Critical Experiment which will provide new critical and reactor physics benchmarks for fuel enrichments greater than five weight percent. The inverse multiplication method was used to determine the state of the system during the course of the experiment. Using the inverse multiplication method, it was determined that the critical experiment went slightly supercritical with 1148 fuel elements in the fuel array. The experiment is described and the results of the experiment are presented. (authors)

  9. Analysis association of milk fat and protein percent in quantitative ...

    African Journals Online (AJOL)

    Analysis association of milk fat and protein percent in quantitative trait locus ... African Journal of Biotechnology ... Protein and fat percent as content of milk are high-priority criteria for financial aims and selection of programs in dairy cattle.

  10. 26 CFR 301.6226(b)-1 - 5-percent group.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 18 2010-04-01 2010-04-01 false 5-percent group. 301.6226(b)-1 Section 301.6226... ADMINISTRATION PROCEDURE AND ADMINISTRATION Assessment In General § 301.6226(b)-1 5-percent group. (a) In general. All members of a 5-percent group shall join in filing any petition for judicial review. The...

  11. High performance Mo adsorbent PZC

    Energy Technology Data Exchange (ETDEWEB)

    Anon,

    1998-10-01

    We have developed Mo adsorbents for natural Mo(n, {gamma}){sup 99}Mo-{sup 99m}Tc generator. Among them, we called the highest performance adsorbent PZC that could adsorb about 250 mg-Mo/g. In this report, we will show the structure, adsorption mechanism of Mo, and the other useful properties of PZC when you carry out the examination of Mo adsorption and elution of {sup 99m}Tc. (author)

  12. Effect of unlabelled monoclonal antibody (MoAb) on biodistribution of /sup 111/Indium labelled (MoAb)

    Energy Technology Data Exchange (ETDEWEB)

    Lamki, L M; Murray, J L; Rosenblum, M G; Patt, Y Z; Babaian, Richard; Unger, M W

    1988-08-01

    We have evaluated immunoscintigraphy in cancer patients using four /sup 111/In-labelled murine monoclonal antibodies (MoAb): 96.5 (anti-P97 of melanoma), ZME-018 (anti-high molecular weight antibody of melanoma), ZCE-025 (anti-CEA for colon cancer) and PAY-276 (anti-prostatic acid phosphatase for prostatic cancer). The effect of increasing the doses of unlabelled MoAb (co-infused with 1 mg labelled MoAb) on the relative body distribution of each labelled MoAb was assessed. Localization in the liver decreased significantly in all cases, with increasing MoAb dose, except for ZME-018. Localization in other organs increased significantly as the liver activity decreased. The spleen activity, however, fell in the case of MoAb ZME-018. Blood-pool activity increased with MoAb dose in all four MoAbs. These findings correlated with the rise in the detection rate of metastases, the plasma half-life, and other pharmacokinetic parameters. However, the dose level at which this correlation occurred varied with each antibody. These data demonstrate the co-infusion of unlabelled MoAb with /sup 111/In-labelled MoAb could alter the organ distribution, pharmacokinetics and tumour uptake in a favourable manner, though the degree to which this occurs depends on the antibody in question.

  13. Decay of 99Mo

    International Nuclear Information System (INIS)

    Dickens, J.K.; Love, T.A.

    1976-01-01

    Relative intensities for K x-rays and gamma rays emanating from 99 Mo in equilibrium with its 99 Tc* daughter have been measured using several Ge photon detectors. Combining these intensities with an evaluated set of electron-conversion coefficients has provided a set of absolute intensities for the observed gamma rays. The absolute intensity for the dominant 140.5-keV gamma ray in 99 Tc was determined to be 90.7 +- 0.6/100 99 Mo disintegrations for 99 Mo decay in equilibrium with decay of the 99 Tc* daughter

  14. Effect of Mo addition on the electrocatalytic activity of Pt-Sn-Mo/C for direct ethanol fuel cells

    International Nuclear Information System (INIS)

    Lee, Eungje; Murthy, Arun; Manthiram, Arumugam

    2011-01-01

    Carbon-supported Pt-Sn-Mo electrocatalysts have been synthesized by a polyol reduction method and characterized for ethanol electro-oxidation reaction (EOR). While the percent loading of the synthesized nanoparticles on the carbon support is higher than 35%, energy dispersive spectroscopy (EDS) reveals that the Mo contents in the nanoparticle catalysts are lower than the nominal value, indicating incomplete reduction of the Mo precursor. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analyses reveal that the Sn and Mo exist as oxide phases at the surface layers of the nanoparticles and the degree of alloying is very low. The electrochemical properties of the electrocatalysts have been evaluated by cyclic voltammetry (CV) and chronoamperometry. The catalytic activity for EOR decreases in the order PtSnMo 0.6 /C > PtSnMo 0.4 /C > PtSn/C. Single cell direct ethanol fuel cell (DEFC) tests also confirm that the PtSnMo 0.6 /C anode catalyst exhibit better performance than the PtSn/C anode catalyst. An analysis of the electrochemical data suggests that the incorporation of Mo to Pt-Sn enhances further the catalytic activity for EOR.

  15. MoEDAL expands

    CERN Multimedia

    Anaïs Schaeffer

    2011-01-01

    The MoEDAL collaboration deployed a test array of 18 plastic Nuclear Track Etch Detector (NTD) stacks – covering an area of 1 m2 – in the MoEDAL/VELO cavern at Point 8 of the LHC ring in November 2009. This small array was supplemented by a further 110 stacks this past January. The MoEDAL test array, which now covers an area of 8 m2, will reveal its secrets early in 2013. The full MoEDAL detector will be installed in the next long shutdown of the LHC in 2013.   View of the MoEDAL detectors installed at Point 8 of the LHC ring in January 2011. MoEDAL (Monopole and Exotics Detector At the LHC), the seventh LHC experiment, was approved by the CERN Research Board at the end of 2009. Its goal is to search for very specific exotics such as highly ionising massive stable (or pseudo-stable) particles with conventional electrical charge and magnetic monopoles. “The main LHC experiments are designed to detect conventionally charged particles, with conventional ionisation patte...

  16. CRED Cumulative Map of Percent Scleractinian Coral Cover at Saipan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  17. CRED Cumulative Map of Percent Scleractinian Coral Cover at Sarigan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  18. CRED Cumulative Map of Percent Scleractinian Coral Cover at Tutuila

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  19. CRED Cumulative Map of Percent Scleractinian Coral Cover at Anatahan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  20. CRED Cumulative Map of Percent Scleractinian Coral Cover at Alamagan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  1. CRED Cumulative Map of Percent Scleractinian Coral Cover at Agrihan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  2. CRED Cumulative Map of Percent Scleractinian Coral Cover at Asuncion

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  3. CRED Cumulative Map of Percent Scleractinian Coral Cover at Aguijan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  4. CRED Cumulative Map of Percent Scleractinian Coral Cover at Pagan

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  5. Microstructure Characterization of WCCo-Mo Based Coatings Produced Using High Velocity Oxygen Fuel

    Directory of Open Access Journals (Sweden)

    Serkan Islak

    2015-12-01

    Full Text Available The present study has been carried out in order to investigate the microstructural properties of WCCo-Mo composite coatings deposited onto a SAE 4140 steel substrate by high velocity oxygen fuel (HVOF thermal spray. For this purpose, the Mo quantity added to the WCCo was changed as 10, 20, 30 and 40 wt. % percents. The coatings are compared in terms of their phase composition, microstructure and hardness. Phase compound and microstructure of coating layers were examined using X-ray diffractometer (XRD and scanning electron microscope (SEM. XRD results showed that WCCo-Mo composite coatings were mainly composed of WC, W2C, Co3W3C, Mo2C, MoO2, Mo and Co phases. The average hardness of the coatings increased with increasing Mo content.

  6. 99Mo production by 100Mo(n,2n)99Mo using accelerator neutrons

    International Nuclear Information System (INIS)

    Sato, Nozomi; Kawabata, Masako; Nagai, Yasuki; Hashimoto, Kazuyuki; Hatsukawa, Yuichi; Saeki, Hideya; Motoishi, Shoji; Kin, Tadahiro; Konno, Chikara; Ochiai, Kentaro; Takakura, Kosuke; Minato, Futoshi; Iwamoto, Osamu; Iwamoto, Nobuyuki; Hashimoto, Shintaro

    2013-01-01

    We proposed a new route to produce a medical radioisotope 99 Mo by the 100 Mo(n,2n) 99 Mo reaction using accelerator neutrons. A high-quality 99 Mo with a minimum level of radioactive waste can be obtained by the proposed reaction. The decay product of 99 Mo, 99m Tc, is separated from 99 Mo by the sublimation method. The proposed route could bring a major breakthrough in the solution of ensuring a constant and reliable supply of 99 Mo. (author)

  7. The relationships between percent body fat and other ...

    African Journals Online (AJOL)

    The relationships between percent body fat and other anthropometric nutritional predictors among male and female children in Nigeria. ... A weak significant positive correlation was observed between the percent body fat and height – armspan ratio ... There was evidence of overweight and obesity in both children. The mid ...

  8. The Texas Ten Percent Plan's Impact on College Enrollment

    Science.gov (United States)

    Daugherty, Lindsay; Martorell, Paco; McFarlin, Isaac, Jr.

    2014-01-01

    The Texas Ten Percent Plan (TTP) provides students in the top 10 percent of their high-school class with automatic admission to any public university in the state, including the two flagship schools, the University of Texas at Austin and Texas A&M. Texas created the policy in 1997 after a federal appellate court ruled that the state's previous…

  9. High-strength uranium-0.8 weight percent titanium alloy penetrators

    International Nuclear Information System (INIS)

    Northcutt, W.G.

    1978-09-01

    Long-rod kinetic-energy penetrators, produced from a uranium-0.8 titanium (U-0.8 Ti) alloy, are normally water quenched from the gamma phase (approximately 800 0 C) and aged to the desired hardness and strength levels. High cooling rates from 800 0 C in U-0.8 Ti alloy cylindrical bodies larger than about 13 mm in diameter cause internal voids, while slower rates of cooling can produce material that is unresponsive to aging. For the present study, elimination of quenching voids was of paramount importance; therefore, a process including the quenching of plate was explored. Vacuum-induction-cast ingots were forged and rolled into plate and cut into blanks from which the penetrators were obtained. Quenched U-0.8 Ti alloy blanks were aged at 350 to 500 0 C to determine the treatment that would provide maximum tensile and impact strengths. Both tensile and impact strengths were maximized by aging in vacuum for six hours at 450 0 C

  10. Microstructural Evolution of Al-1Fe (Weight Percent) Alloy During Accumulative Continuous Extrusion Forming

    Science.gov (United States)

    Wang, Xiang; Guan, Ren-Guo; Tie, Di; Shang, Ying-Qiu; Jin, Hong-Mei; Li, Hong-Chao

    2018-04-01

    As a new microstructure refining method, accumulative continuous extrusion forming (ACEF) cannot only refine metal matrix but also refine the phases that exist in it. In order to detect the refinements of grain and second phase during the process, Al-1Fe (wt pct) alloy was processed by ACEF, and the microstructural evolution was analyzed by electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Results revealed that the average grain size of Al-1Fe (wt pct) alloy decreased from 13 to 1.2 μm, and blocky Al3Fe phase with an average length of 300 nm was granulated to Al3Fe particle with an average diameter of 200 nm, after one pass of ACEF. Refinement of grain was attributed to continuous dynamic recrystallization (CDRX), and the granulation of Al3Fe phase included the spheroidization resulting from deformation heat and the fragmentation caused by the coupling effects of strain and thermal effect. The spheroidization worked in almost the entire deformation process, while the fragmentation required strain accumulation. However, fragmentation contributed more than spheroidization. Al3Fe particle stimulated the formation of substructure and retarded the migration of recrystallized grain boundary, but the effect of Al3Fe phase on refinement of grain could only be determined by the contrastive investigation of Al-1Fe (wt pct) alloy and pure Al.

  11. Impact strength of the uranium-6 weight percent niobium alloy between -1980 and +2000C

    International Nuclear Information System (INIS)

    Anderson, R.C.

    1981-09-01

    A study was conducted to determine if a ductile-to-brittle transition wxisted for the uranium-6 wt % niobium (U-6Nb) alloy. Standard V-notched Charpy bars were made from both solution-quenched and solution-quenched and aged U-6Nb alloy and were tested between -198 0 and +200 0 C. It was found that a sharp ductile-brittle transition does not exist for the alloy. A linear relationship existed between test temperature and impact strength, and the alloy retained a significant amount of impact strength even at very low temperatures. 9 figures

  12. Preparation, heat treatment, and mechanical properties of the uranium-5 weight percent chromium eutectic alloy

    International Nuclear Information System (INIS)

    Townsend, A.B.

    1980-10-01

    The eutectic alloy of uranium-5 wt % chromium (U-5Cr) was prepared from high-purity materials and cast into 1-in.-thick ingots. This material was given several simple heat treatments, the mechanical properties of these heat-treated samples were determined; and the microstructure was examined. Some data on the melting point and transformation temperatures were obtained

  13. National Land Cover Database (NLCD) Percent Tree Canopy Collection

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The National Land Cover Database (NLCD) Percent Tree Canopy Collection is a product of the U.S. Forest Service (USFS), and is produced through a cooperative project...

  14. National Land Cover Database (NLCD) Percent Developed Imperviousness Collection

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The National Land Cover Database (NLCD) Percent Developed Imperviousness Collection is produced through a cooperative project conducted by the Multi-Resolution Land...

  15. Determination of percent calcium carbonate in calcium chromate

    International Nuclear Information System (INIS)

    Middleton, H.W.

    1979-01-01

    The precision, accuracy and reliability of the macro-combustion method is superior to the Knorr alkalimetric method, and it is faster. It also significantly reduces the calcium chromate waste accrual problem. The macro-combustion method has been adopted as the official method for determination of percent calcium carbonate in thermal battery grade anhydrous calcium chromate and percent calcium carbonate in quicklime used in the production of calcium chromate. The apparatus and procedure can be used to measure the percent carbonate in inorganic materials other than calcium chromate. With simple modifications in the basic apparatus and procedure, the percent carbon and hydrogen can be measured in many organic material, including polymers and polymeric formulations. 5 figures, 5 tables

  16. Thermal and x-ray studies on Tl2U(MoO4)3 and Tl4U(MoO4)4

    International Nuclear Information System (INIS)

    Dahale, N.D.; Keskar, Meera; Kulkarni, N.K.; Singh Mudher, K.D.

    2006-01-01

    In the quaternary Tl-U(IV)-Mo-O system, two new compounds namely Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 were prepared and characterized by powder X-ray diffraction and thermal methods. These compounds were prepared by solid state reactions of Tl 2 MoO 4 , UMoO 5 and MoO 3 in the required stoichiometric ratio at 500 deg C in evacuated sealed quartz ampoule. The XRD data of Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 were indexed on orthorhombic cell. TG curves of Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 did not show any weight change up to 700 deg C in an inert atmosphere. During heating in an inert atmosphere, Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 showed endothermic Dta peaks due to melting of the compounds at 519 and 565 deg C, respectively. (author)

  17. RoMo

    DEFF Research Database (Denmark)

    Pedersen, Esben Warming; Hornbæk, Kasper

    2011-01-01

    In TUIs, physical/digital conflicts can occur when the digital model does not match the model implied by the spatial lay- out of tangibles. We show how tangible tabletop interfaces (TTI) can be modified to allow robot movement of tangi- bles, thereby avoiding conflicts. We present RoMo, an open...... source Java library that allow existing TTI applications to perform robot movement, and demonstrate its functionality with three applications....

  18. Modeling percent tree canopy cover: a pilot study

    Science.gov (United States)

    John W. Coulston; Gretchen G. Moisen; Barry T. Wilson; Mark V. Finco; Warren B. Cohen; C. Kenneth Brewer

    2012-01-01

    Tree canopy cover is a fundamental component of the landscape, and the amount of cover influences fire behavior, air pollution mitigation, and carbon storage. As such, efforts to empirically model percent tree canopy cover across the United States are a critical area of research. The 2001 national-scale canopy cover modeling and mapping effort was completed in 2006,...

  19. Age-specific association between percent body fat and pulmonary ...

    African Journals Online (AJOL)

    This study describes the association between percent body fat and pulmonary function among apparently normal twenty male children tidal volume aged 4 years and twenty male children aged 10 years in Ogbomoso. The mean functional residual capacity of the lung in male children aged 10 years was significantly higher ...

  20. Analysis association of milk fat and protein percent in quantitative ...

    African Journals Online (AJOL)

    SAM

    2014-05-14

    May 14, 2014 ... African Journal of Biotechnology. Full Length ... quantitative trait locus (QTLs) on chromosomes 1, 6, 7 and 20 in ... Protein and fat percent as content of milk are high-priority criteria for financial aims and selection of programs ...

  1. Evaluating Equating Results: Percent Relative Error for Chained Kernel Equating

    Science.gov (United States)

    Jiang, Yanlin; von Davier, Alina A.; Chen, Haiwen

    2012-01-01

    This article presents a method for evaluating equating results. Within the kernel equating framework, the percent relative error (PRE) for chained equipercentile equating was computed under the nonequivalent groups with anchor test (NEAT) design. The method was applied to two data sets to obtain the PRE, which can be used to measure equating…

  2. School Designed To Use 80 Percent Less Energy

    Science.gov (United States)

    American School and University, 1975

    1975-01-01

    The new Terraset Elementary School in Reston, Virginia, uses earth as a cover for the roof area and for about 80 percent of the wall area. A heat recovery system will be used with solar collectors playing a primary role in heating and cooling. (Author/MLF)

  3. U-Mo/Al-Si interaction: Influence of Si concentration

    International Nuclear Information System (INIS)

    Allenou, J.; Palancher, H.; Iltis, X.; Cornen, M.; Tougait, O.; Tucoulou, R.; Welcomme, E.; Martin, Ph.; Valot, C.; Charollais, F.; Anselmet, M.C.; Lemoine, P.

    2010-01-01

    Within the framework of the development of low enriched nuclear fuels for research reactors, U-Mo/Al is the most promising option that has however to be optimised. Indeed at the U-Mo/Al interfaces between U-Mo particles and the Al matrix, an interaction layer grows under irradiation inducing an unacceptable fuel swelling. Adding silicon in limited content into the Al matrix has clearly improved the in-pile fuel behaviour. This breakthrough is attributed to an U-Mo/Al-Si protective layer around U-Mo particles appeared during fuel manufacturing. In this work, the evolution of the microstructure and composition of this protective layer with increasing Si concentrations in the Al matrix has been investigated. Conclusions are based on the characterization at the micrometer scale (X-ray diffraction and energy dispersive spectroscopy) of U-Mo7/Al-Si diffusion couples obtained by thermal annealing at 450 deg. C. Two types of interaction layers have been evidenced depending on the Si content in the Al-Si alloy: the threshold value is found at about 5 wt.% but obviously evolves with temperature. It has been shown that for Si concentrations ranging from 2 to 10 wt.%, the U-Mo7/Al-Si interaction is bi-layered and the Si-rich part is located close to the Al-Si for low Si concentrations (below 5 wt.%) and close to the U-Mo for higher Si concentrations. For Si weight fraction in the Al alloy lower than 5 wt.%, the Si-rich sub-layer (close to Al-Si) consists of U(Al, Si) 3 + UMo 2 Al 20 , when the other sub-layer (close to U-Mo) is silicon free and made of UAl 3 and U 6 Mo 4 Al 43 . For Si weight concentrations above 5 wt.%, the Si-rich part becomes U 3 (Si, Al) 5 + U(Al, Si) 3 (close to U-Mo) and the other sub-layer (close to Al-Si) consists of U(Al, Si) 3 + UMo 2 Al 20 . On the basis of these results and of a literature survey, a scheme is proposed to explain the formation of different types of ILs between U-Mo and Al-Si alloys (i.e. different protective layers).

  4. Matter power spectrum and the challenge of percent accuracy

    International Nuclear Information System (INIS)

    Schneider, Aurel; Teyssier, Romain; Potter, Doug; Stadel, Joachim; Reed, Darren S.; Onions, Julian; Pearce, Frazer R.; Smith, Robert E.; Springel, Volker; Scoccimarro, Roman

    2016-01-01

    Future galaxy surveys require one percent precision in the theoretical knowledge of the power spectrum over a large range including very nonlinear scales. While this level of accuracy is easily obtained in the linear regime with perturbation theory, it represents a serious challenge for small scales where numerical simulations are required. In this paper we quantify the precision of present-day N -body methods, identifying main potential error sources from the set-up of initial conditions to the measurement of the final power spectrum. We directly compare three widely used N -body codes, Ramses, Pkdgrav3, and Gadget3 which represent three main discretisation techniques: the particle-mesh method, the tree method, and a hybrid combination of the two. For standard run parameters, the codes agree to within one percent at k ≤1 h Mpc −1 and to within three percent at k ≤10 h Mpc −1 . We also consider the bispectrum and show that the reduced bispectra agree at the sub-percent level for k ≤ 2 h Mpc −1 . In a second step, we quantify potential errors due to initial conditions, box size, and resolution using an extended suite of simulations performed with our fastest code Pkdgrav3. We demonstrate that the simulation box size should not be smaller than L =0.5 h −1 Gpc to avoid systematic finite-volume effects (while much larger boxes are required to beat down the statistical sample variance). Furthermore, a maximum particle mass of M p =10 9 h −1 M ⊙ is required to conservatively obtain one percent precision of the matter power spectrum. As a consequence, numerical simulations covering large survey volumes of upcoming missions such as DES, LSST, and Euclid will need more than a trillion particles to reproduce clustering properties at the targeted accuracy.

  5. Matter power spectrum and the challenge of percent accuracy

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Aurel; Teyssier, Romain; Potter, Doug; Stadel, Joachim; Reed, Darren S. [Institute for Computational Science, University of Zurich, Winterthurerstrasse 190, 8057 Zurich (Switzerland); Onions, Julian; Pearce, Frazer R. [School of Physics and Astronomy, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Smith, Robert E. [Department of Physics and Astronomy, University of Sussex, Brighton, BN1 9QH (United Kingdom); Springel, Volker [Heidelberger Institut für Theoretische Studien, 69118 Heidelberg (Germany); Scoccimarro, Roman, E-mail: aurel@physik.uzh.ch, E-mail: teyssier@physik.uzh.ch, E-mail: dpotter@physik.uzh.ch, E-mail: stadel@physik.uzh.ch, E-mail: julian.onions@nottingham.ac.uk, E-mail: reed@physik.uzh.ch, E-mail: r.e.smith@sussex.ac.uk, E-mail: volker.springel@h-its.org, E-mail: Frazer.Pearce@nottingham.ac.uk, E-mail: rs123@nyu.edu [Center for Cosmology and Particle Physics, Department of Physics, New York University, NY 10003, New York (United States)

    2016-04-01

    Future galaxy surveys require one percent precision in the theoretical knowledge of the power spectrum over a large range including very nonlinear scales. While this level of accuracy is easily obtained in the linear regime with perturbation theory, it represents a serious challenge for small scales where numerical simulations are required. In this paper we quantify the precision of present-day N -body methods, identifying main potential error sources from the set-up of initial conditions to the measurement of the final power spectrum. We directly compare three widely used N -body codes, Ramses, Pkdgrav3, and Gadget3 which represent three main discretisation techniques: the particle-mesh method, the tree method, and a hybrid combination of the two. For standard run parameters, the codes agree to within one percent at k ≤1 h Mpc{sup −1} and to within three percent at k ≤10 h Mpc{sup −1}. We also consider the bispectrum and show that the reduced bispectra agree at the sub-percent level for k ≤ 2 h Mpc{sup −1}. In a second step, we quantify potential errors due to initial conditions, box size, and resolution using an extended suite of simulations performed with our fastest code Pkdgrav3. We demonstrate that the simulation box size should not be smaller than L =0.5 h {sup −1}Gpc to avoid systematic finite-volume effects (while much larger boxes are required to beat down the statistical sample variance). Furthermore, a maximum particle mass of M {sub p}=10{sup 9} h {sup −1}M{sub ⊙} is required to conservatively obtain one percent precision of the matter power spectrum. As a consequence, numerical simulations covering large survey volumes of upcoming missions such as DES, LSST, and Euclid will need more than a trillion particles to reproduce clustering properties at the targeted accuracy.

  6. New formula for calculation of cobalt-60 percent depth dose

    International Nuclear Information System (INIS)

    Tahmasebi Birgani, M. J.; Ghorbani, M.

    2005-01-01

    On the basis of percent depth dose calculation, the application of - dosimetry in radiotherapy has an important role to play in reducing the chance of tumor recurrence. The aim of this study is to introduce a new formula for calculating the central axis percent depth doses of Cobalt-60 beam. Materials and Methods: In the present study, based on the British Journal of Radiology table, nine new formulas are developed and evaluated for depths of 0.5 - 30 cm and fields of (4*4) - (45*45) cm 2 . To evaluate the agreement between the formulas and the table, the average of the absolute differences between the values was used and the formula with the least average was selected as the best fitted formula. The Microsoft Excel 2000 and the Data fit 8.0 soft wares were used to perform the calculations. Results: The results of this study indicated that one amongst the nine formulas gave a better agreement with the percent depth doses listed in the table of British Journal of Radiology . The new formula has two parts in terms of log (A/P). The first part as a linear function with the depth in the range of 0.5 to 5 cm and the other one as a second order polynomial with the depth in the range of 6 to 30 cm. The average of - the differences between the tabulated and the calculated data using the formula (Δ) is equal to 0.3 152. Discussion and Conclusion: Therefore, the calculated percent depth dose data based on this formula has a better agreement with the published data for Cobalt-60 source. This formula could be used to calculate the percent depth dose for the depths and the field sizes not listed in the British Journal of Radiology table

  7. Diffusion barrier performances of thin Mo, Mo-N and Mo/Mo-N films between Cu and Si

    International Nuclear Information System (INIS)

    Song Shuangxi; Liu Yuzhang; Mao Dali; Ling Huiqin; Li Ming

    2005-01-01

    In this work, we have studied the diffusion barrier performances of Mo, Mo-N and Mo/Mo-N metallization layers deposited by sputtering Mo in Ar/N 2 atmospheres, respectively. Samples were subsequently annealed at different temperatures ranging from 400 to 800 deg C in vacuum condition. The film properties and their suitability as diffusion barriers and protective coatings in silicon devices were characterized using four-point probe measurement, X-ray diffractometry, scanning electron microscopy, Auger electron spectroscopy and transmission electron microscopy analyses. Experimental results revealed that the Mo (20 nm)/Mo-N (30 nm) layer was able to prevent the diffusion reaction between Cu and Si substrate after being annealed at 600 deg C for 30 min. The adhesion between layers and the content of N atoms are the key parameters to improve the properties of Mo-based barrier materials. The Mo layer interposed between Cu and Mo-N diluted the high nitrogen concentration of the barrier and so enhanced the barrier performances

  8. An experimental investigation of the rate of hydrogen absorption in zirconium-2.5 wt percent niobium from steam/hydrogen mixtures at elevated temperatures

    International Nuclear Information System (INIS)

    Langman, V.J.

    1984-08-01

    The test specifications for an experimental program to study the rate of hydrogen absorption in zirconium-2.5 weight percent niobium pressure tube material from steam/hydrogen mixtures at elevated temperatures are discussed

  9. Breastfeeding reduces postpartum weight retention

    DEFF Research Database (Denmark)

    Baker, Jennifer Lyn; Gamborg, Michael; Heitmann, Berit L

    2008-01-01

    BACKGROUND: Weight gained during pregnancy and not lost postpartum may contribute to obesity in women of childbearing age. OBJECTIVE: We aimed to determine whether breastfeeding reduces postpartum weight retention (PPWR) in a population among which full breastfeeding is common and breastfeeding...... duration is long. DESIGN: We selected women from the Danish National Birth Cohort who ever breastfed (>98%), and we conducted the interviews at 6 (n = 36 030) and 18 (n = 26 846) mo postpartum. We used regression analyses to investigate whether breastfeeding (scored to account for duration and intensity......) reduced PPWR at 6 and 18 mo after adjustment for maternal prepregnancy body mass index (BMI) and gestational weight gain (GWG). RESULTS: GWG was positively (P postpartum. Breastfeeding was negatively associated with PPWR in all women but those...

  10. Matter power spectrum and the challenge of percent accuracy

    OpenAIRE

    Schneider, Aurel; Teyssier, Romain; Potter, Doug; Stadel, Joachim; Onions, Julian; Reed, Darren S.; Smith, Robert E.; Springel, Volker; Pearce, Frazer R.; Scoccimarro, Roman

    2015-01-01

    Future galaxy surveys require one percent precision in the theoretical knowledge of the power spectrum over a large range including very nonlinear scales. While this level of accuracy is easily obtained in the linear regime with perturbation theory, it represents a serious challenge for small scales where numerical simulations are required. In this paper we quantify the precision of present-day $N$-body methods, identifying main potential error sources from the set-up of initial conditions to...

  11. High conductivity graphene-like MoS2/polyaniline nanocomposites and its application in supercapacitor

    International Nuclear Information System (INIS)

    Wang, Jin; Wu, Zongchao; Hu, Kunhong; Chen, Xiangying; Yin, Huabing

    2015-01-01

    Highlights: • A facile synthesis method of MoS 2 /PANI intercalated nanocomposites is developed. • There is synergistic effect between PANI and MoS 2 layer in the MoS 2 /PANI composites. • Intercalation is benefit for electrons transportation and conductivity increase. • The well-defined MoS 2 /PANI have good specific capacitances and long cyclic life. - Abstract: High conductivity nanocomposites of molybdenum disulfide (MoS 2 )/polyaniline (PANI) were prepared via direct intercalation of aniline monomer and doped with dodecyl benzene sulfonic acid (DBSA). The intercalated interaction between PANI and MoS 2 improves the conductivity and thermal stability of MoS 2 /PANI nanocomposites with the increasing fraction of MoS 2 . The conductivity and maximum weight loss velocity temperature of PANI/MoS 2 -38 sample are 2.38 S cm −1 and 353 °C, respectively. This architecture is also advantageous for enhancing the capacitance properties and cyclic stabilities of MoS 2 /PANI electrodes. In comparison to the specific capacitance of 131 F/g and 42% retained capacitance over 600 cycles of PANI electrode, the MoS 2 /PANI-38 electrode provides a specific capacitance up to 390 F/g and 86% retained capacitance over 1000 cycles. Thus it provides an improved capacitance method which synergistically combines pseudocapacitance and double-layer capacitance for supercapacitor electrodes

  12. Relationship between breast sound speed and mammographic percent density

    Science.gov (United States)

    Sak, Mark; Duric, Nebojsa; Boyd, Norman; Littrup, Peter; Myc, Lukasz; Faiz, Muhammad; Li, Cuiping; Bey-Knight, Lisa

    2011-03-01

    Despite some shortcomings, mammography is currently the standard of care for breast cancer screening and diagnosis. However, breast ultrasound tomography is a rapidly developing imaging modality that has the potential to overcome the drawbacks of mammography. It is known that women with high breast densities have a greater risk of developing breast cancer. Measuring breast density is accomplished through the use of mammographic percent density, defined as the ratio of fibroglandular to total breast area. Using an ultrasound tomography (UST) prototype, we created sound speed images of the patient's breast, motivated by the fact that sound speed in a tissue is proportional to the density of the tissue. The purpose of this work is to compare the acoustic performance of the UST system with the measurement of mammographic percent density. A cohort of 251 patients was studied using both imaging modalities and the results suggest that the volume averaged breast sound speed is significantly related to mammographic percent density. The Spearman correlation coefficient was found to be 0.73 for the 175 film mammograms and 0.69 for the 76 digital mammograms obtained. Since sound speed measurements do not require ionizing radiation or physical compression, they have the potential to form the basis of a safe, more accurate surrogate marker of breast density.

  13. Weight Management

    Science.gov (United States)

    ... Health Information Weight Management English English Español Weight Management Obesity is a chronic condition that affects more ... Liver (NASH) Heart Disease & Stroke Sleep Apnea Weight Management Topics About Food Portions Bariatric Surgery for Severe ...

  14. Oxidation behavior of Mo-based alloys coated with silicide using the halide-activated pack cementation method

    International Nuclear Information System (INIS)

    Ito, K.; Hayashi, T.; Yamaguchi, M.; Murakami, T.

    2003-01-01

    This article summarizes recent progress in research on oxidation behavior of pack-cemented Mo-9Si-18B alloys with a Mo 5 SiB 2 /Mo two-phase eutectic microstructure. The deposited layer of as-cemented Mo-9Si-18B alloy consists of MoSi 2 . Upon heating to temperatures above 1500 C, the deposited layer is transformed into B-doped Mo 5 Si 3 through a reaction between the deposited layer and the matrix containing B. Steady-state oxidation is observed at 1300-1500 C and its rates are almost equal to those of MoSi 2 . No significant increase in weight loss was observed in a short-term cyclic oxidation test, since the columnar structure with orientation preference in B-doped Mo 5 Si 3 coating layer must be reduced thermal stress in the cyclic oxidation test. (orig.)

  15. Strengthening by ordered precipitates in a Ni--Ni4Mo system

    International Nuclear Information System (INIS)

    Goodrum, J.W.; LeFevre, B.G.

    1977-01-01

    The strength characteristics and microstructures of aged Ni-Mo alloys containing ordered (Ni 4 Mo) precipitates were studied as a function of aging time and temperature. It was found that 17 at. percent Mo alloy aged at 750 0 C produced a uniform dispersion of cuboidal β precipitates which coarsened with time producing a gradual increase in flow stress. The flow stress increment was found to vary in qualitative agreement with both order strengthening and coherency strain models. Both these models give over-estimates of the strengthening increment. A negative dependence of flow stress on temperature is attributed to coherency strain contributions

  16. 7 CFR 981.401 - Adjusted kernel weight.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Adjusted kernel weight. 981.401 Section 981.401... Administrative Rules and Regulations § 981.401 Adjusted kernel weight. (a) Definition. Adjusted kernel weight... kernels in excess of five percent; less shells, if applicable; less processing loss of one percent for...

  17. Characterization of Thin Walled Mo Tubing produced by FBCVD

    Energy Technology Data Exchange (ETDEWEB)

    Beaux, Miles Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Usov, Igor Olegovich [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-01-21

    The goal of this report is to delineate the results of material characterization performed on Mo tubing produced via the fluidized bed chemical vapor deposition (FBCVD) method. Scanning electron microscopy (SEM) imaging reveals that small randomly oriented grains are achieved in the Mo deposition, but do not persist throughout the entire thickness of the material. Energy dispersive spectroscopy (EDS) reveals the Mo tubes contain residual chlorine and oxygen. EDS measurements on the tube surfaces separated from glass and quartz substrates reveal substrate material adhered to this surface. X-ray diffraction (XRD) revealed the presence of carbon contaminant in the form of Mo2C and oxygen in the form of MoO2. Combustion infrared detection (CID) and inert gas fusion (IGF) performed at Luvak Inc. was used to quantify weight percentages of oxygen and carbon in the tubes produced. Hardness value of the FBCVD Mo was found to be comparable to low carbon arc cast molybdenum.

  18. Wear tests in a hip joint simulator of different CoCrMo counterfaces on UHMWPE

    International Nuclear Information System (INIS)

    Gonzalez-Mora, V.A.; Hoffmann, M.; Stroosnijder, R.; Gil, F.J.

    2009-01-01

    The objective in this work was to study the effect of different material counterfaces on the Ultra High Molecular Weight Polyethylene (UHMWPE) wear behavior. The materials used as counterfaces were based on CoCrMo: forged with hand polished and mass finished, CoCrMo coating applied on the forged CoCrMo alloy obtained by Physical Vapour Deposition (PVD). A hip joint simulator was designed and built for these studies. The worn surfaces were observed by optical and scanning electron microscopy. The results showed that the hand polished CoCrMo alloy caused the higher UHMWPE wear of the acetabular cups. The CoCrMo coating caused the least UHMWPE wear, while the mass finished CoCrMo alloy caused an intermediate UHMWPE wear. It is shown that the wear rates obtained in this work are closer to clinical studies than to similar hip joints simulator studies

  19. Comparison of the Isothermal Oxidation Behavior of As-Cast Cu-17 Percent Cr and Cu-17 Percent Cr-5 Percent Al. Part 1; Oxidation Kinetics

    Science.gov (United States)

    Raj, S. V.

    2008-01-01

    The isothermal oxidation kinetics of as-cast Cu-17%Cr and Cu-17%Cr-5%Al in air were studied between 773 and 1173 K under atmospheric pressure. These observations reveal that Cu-17%Cr-5%Al oxidizes at significantly slower rates than Cu-17%Cr. The rate constants for the alloys were determined from generalized analyses of the data without an a priori assumption of the nature of the oxidation kinetics. Detailed analyses of the isothermal thermogravimetric weight change data revealed that Cu-17%Cr exhibited parabolic oxidation kinetics with an activation energy of 165.9+/-9.5 kJ/mol. In contrast, the oxidation kinetics for the Cu-17%Cr-5%Al alloy exhibited a parabolic oxidation kinetics during the initial stages followed by a quartic relationship in the later stages of oxidation. Alternatively, the oxidation behavior of Cu-17%CR-5%Al could be better represented by a logarithmic relationship. The parabolic rate constants and activation energy data for the two alloys are compared with literature data to gain insights on the nature of the oxidation mechanisms dominant in these alloys.

  20. Fission 99Mo production technology

    International Nuclear Information System (INIS)

    Miao Zengxing; Luo Zhifu; Ma Huimin; Liang Yufu; Yu Ningwen

    2003-01-01

    This paper describes a production technology of fission 99 Mo in the Department Isotope, CIAE. The irradiation target is tubular U-Al alloy containing highly enriched uranium. The target is irradiated in the swimming pool reactor core. The neutron flux is about 4x10 13 /cm 2 .sec. The production scale is 3.7-7.4 TBq (100-200Ci) of fission 99 Mo per batch. Total recovery of 99 Mo is more than 70%. The production practice proves that the process and equipment are safe and reliable. (author)

  1. Ineffectiveness of commercial weight-loss programs for achieving modest but meaningful weight loss: Systematic review and meta-analysis.

    Science.gov (United States)

    McEvedy, Samantha M; Sullivan-Mort, Gillian; McLean, Siân A; Pascoe, Michaela C; Paxton, Susan J

    2017-10-01

    This study collates existing evidence regarding weight loss among overweight but otherwise healthy adults who use commercial weight-loss programs. Systematic search of 3 databases identified 11 randomized controlled trials and 14 observational studies of commercial meal-replacement, calorie-counting, or pre-packaged meal programs which met inclusion criteria. In meta-analysis using intention-to-treat data, 57 percent of individuals who commenced a commercial weight program lost less than 5 percent of their initial body weight. One in two (49%) studies reported attrition ≥30 percent. A second meta-analysis found that 37 percent of program completers lost less than 5 percent of initial body weight. We conclude that commercial weight-loss programs frequently fail to produce modest but clinically meaningful weight loss with high rates of attrition suggesting that many consumers find dietary changes required by these programs unsustainable.

  2. First-principles study of the surface properties of U-Mo system

    Energy Technology Data Exchange (ETDEWEB)

    Mei, Zhi-Gang; Liang, Linyun; Yacout, Abdellatif M.

    2018-02-01

    U-Mo alloys are promising fuels for future high-performance research reactors with low enriched uranium. Surface properties, such as surface energy, are important inputs for mesoscale simulations (e.g., phase field method) of fission gas bubble behaviors in irradiated nuclear fuels. The lack of surface energies of U-Mo alloys prevents an accurate modeling of the morphology of gas bubbles and gas bubble-induced fuel swelling. To this end, we study the surface properties of U-Mo system, including bcc Mo, alpha-U, gamma-U, and gamma U-Mo alloys. All surfaces up to a maximum Miller index of three and two are calculated for cubic Mo and gamma-U and non-cubic alpha-U, respectively. The equilibrium crystal shapes of bcc Mo, alpha-U and gamma-U are constructed using the calculated surface energies. The dominant surface orientations and the area fraction of each facet are determined from the constructed equilibrium crystal shape. The disordered gamma U-Mo alloys are simulated using the Special Quasirandom Structure method. The (1 1 0) and (1 0 0) surface energies of gamma U-7Mo and U-10Mo alloys are predicted to lie between those of gamma-U and bcc Mo, following a linear combination of the two constituents' surface energies. To better compare with future measurements of surface energies, the area fraction weighted surface energies of alpha-U, gamma-U and gamma U-7Mo and U-10Mo alloys are also predicted. (C) 2017 Published by Elsevier B.V.

  3. Family Weight School treatment

    DEFF Research Database (Denmark)

    Nowicka, Paulina; Höglund, Peter; Pietrobelli, Angelo

    2008-01-01

    OBJECTIVE: The aim was to evaluate the efficacy of a Family Weight School treatment based on family therapy in group meetings with adolescents with a high degree of obesity. METHODS: Seventy-two obese adolescents aged 12-19 years old were referred to a childhood obesity center by pediatricians...... and school nurses and offered a Family Weight School therapy program in group meetings given by a multidisciplinary team. Intervention was compared with an untreated waiting list control group. Body mass index (BMI) and BMI z-scores were calculated before and after intervention. RESULTS: Ninety percent...... group with initial BMI z-score 3.5. CONCLUSIONS: Family Weight School treatment model might be suitable for adolescents with BMI z...

  4. Weighted Clustering

    DEFF Research Database (Denmark)

    Ackerman, Margareta; Ben-David, Shai; Branzei, Simina

    2012-01-01

    We investigate a natural generalization of the classical clustering problem, considering clustering tasks in which different instances may have different weights.We conduct the first extensive theoretical analysis on the influence of weighted data on standard clustering algorithms in both...... the partitional and hierarchical settings, characterizing the conditions under which algorithms react to weights. Extending a recent framework for clustering algorithm selection, we propose intuitive properties that would allow users to choose between clustering algorithms in the weighted setting and classify...

  5. Iron phosphate glass: a promising matrix for the immobilization of Cs and Mo

    International Nuclear Information System (INIS)

    Hemadevi, V.; Joseph, Kitheri

    2015-01-01

    Presently, borosilicate glass (BSG) is the acceptable vitrification matrix for the immobilization of high level waste. The solubility of Mo in BSG is limited in the presence of Cs. As per the literature, solubility of Mo in BSG is about 2.5 wt. % in the presence of Cs. Hence it is difficult to immobilize nuclear waste rich in Cs and Mo in borosilicate glass. It is observed that the composition of Cs and Mo expressed as oxides are 10.4 and 14.7 wt. % respectively in simulated fast reactor waste. Iron phosphate glass containing 20 wt. % simulated fast reactor waste (referred as IP20FRW) was synthesized and characterized. IP20FRW contains ~ 3 wt. % of molybdenum oxide along with 2 wt. % cesium oxide. IPG is a suitable matrix for the immobilization of Cs and Mo separately. Hence it is essential to understand the glass characteristics of IPG containing both Cs and Mo. This paper explores systematic loading of both Cs and Mo such that the final composition corresponds to 10.5 wt. % Cs 2 O-15 wt. % MoO 3 -31.9 wt. % Fe 2 O 3 -42.6 wt. % P 2 O 5 . In addition to synthesis, the present study also includes understanding the change in glass characteristics of IPG containing both Cs and Mo. The possibility of higher percent loading of both Cs and Mo in IPG demonstrates the better glass forming characteristics of IPG. The synthesis and characterization of Cs-Mo loaded glasses will be discussed in this paper. (author)

  6. Preparation of MoB and MoB-MoSi2 composites by combustion synthesis in SHS mode

    International Nuclear Information System (INIS)

    Yeh, C.L.; Hsu, W.S.

    2007-01-01

    Combustion synthesis in the mode of self-propagating high-temperature synthesis (SHS) was carried out in the Mo-B and Mo-B-Si systems for the preparation of molybdenum boride MoB and the composite of MoB-MoSi 2 from elemental powder compacts. Under a preheating temperature above 150 deg. C , the reaction of Mo with boron in the sample compact of Mo:B = 1:1 is characterized by a planar combustion front propagating in a self-sustaining and steady manner. As the preheating temperature or sample compaction density increased, combustion temperature was found to increase and the propagation rate of the combustion front was correspondingly enhanced. Moreover, the XRD analysis provides evidence of yielding nearly single-phase α-MoB from the Mo-B sample at equiatomic stoichiometry. In the synthesis of MoB-MoSi 2 composites, the starting stoichiometry of the Mo-B-Si powder compact was varied so as to produce the final composites containing 20-80 mol% MoB. It was also found the increase of flame-front velocity and combustion temperature with increasing MoB content formed in the composite. The composition analysis by XRD shows excellent conversion from the Mo-B-Si powder compact to the MoB-MoSi 2 composite through the SHS reaction; that is, in addition to a small amount of Mo 5 Si 3 , the as-synthesized composite is composed entirely of MoB and MoSi 2

  7. One Percent Determination of the Primordial Deuterium Abundance

    Science.gov (United States)

    Cooke, Ryan J.; Pettini, Max; Steidel, Charles C.

    2018-03-01

    We report a reanalysis of a near-pristine absorption system, located at a redshift {z}abs}=2.52564 toward the quasar Q1243+307, based on the combination of archival and new data obtained with the HIRES echelle spectrograph on the Keck telescope. This absorption system, which has an oxygen abundance [O/H] = ‑2.769 ± 0.028 (≃1/600 of the solar abundance), is among the lowest metallicity systems currently known where a precise measurement of the deuterium abundance is afforded. Our detailed analysis of this system concludes, on the basis of eight D I absorption lines, that the deuterium abundance of this gas cloud is {log}}10({{D}}/{{H}})=-4.622+/- 0.015, which is in very good agreement with the results previously reported by Kirkman et al., but with an improvement on the precision of this single measurement by a factor of ∼3.5. Combining this new estimate with our previous sample of six high precision and homogeneously analyzed D/H measurements, we deduce that the primordial deuterium abundance is {log}}10{({{D}}/{{H}})}{{P}}=-4.5974+/- 0.0052 or, expressed as a linear quantity, {10}5{({{D}}/{{H}})}{{P}}=2.527+/- 0.030; this value corresponds to a one percent determination of the primordial deuterium abundance. Combining our result with a big bang nucleosynthesis (BBN) calculation that uses the latest nuclear physics input, we find that the baryon density derived from BBN agrees to within 2σ of the latest results from the Planck cosmic microwave background data. Based on observations collected at the W.M. Keck Observatory which is operated as a scientific partnership among the California Institute of Technology, the University of California, and the National Aeronautics and Space Administration. The Observatory was made possible by the generous financial support of the W.M. Keck Foundation.

  8. 99Mo Yield Using Large Sample Mass of MoO3 for Sustainable Production of 99Mo

    Science.gov (United States)

    Tsukada, Kazuaki; Nagai, Yasuki; Hashimoto, Kazuyuki; Kawabata, Masako; Minato, Futoshi; Saeki, Hideya; Motoishi, Shoji; Itoh, Masatoshi

    2018-04-01

    A neutron source from the C(d,n) reaction has the unique capability of producing medical radioisotopes such as 99Mo with a minimum level of radioactive waste. Precise data on the neutron flux are crucial to determine the best conditions for obtaining the maximum yield of 99Mo. The measured yield of 99Mo produced by the 100Mo(n,2n)99Mo reaction from a large sample mass of MoO3 agrees well with the numerical result estimated with the latest neutron data, which are a factor of two larger than the other existing data. This result establishes an important finding for the domestic production of 99Mo: approximately 50% of the demand for 99Mo in Japan could be met using a 100 g 100MoO3 sample mass with a single accelerator of 40 MeV, 2 mA deuteron beams.

  9. Mo and Ni Removal from Drinking Water Using Zeolitic Tuff from Jordan

    Directory of Open Access Journals (Sweden)

    Khalil M. Ibrahim

    2016-11-01

    Full Text Available Mo and Ni metals could be hazardous in natural waters. The initial Mo and Ni concentration in the sampled domestic drinking water of north Jordan is 550 and 110 μg/L, respectively. The efficiency of using natural faujasite–phillipsite and phillipsite–chabazite tuffs in removing Mo and Ni from contaminated drinking water was tested. Batch experiments using different weights of the adsorbent were conducted at different contact times to determine the optimum conditions. The maximal uptake capacity of Mo from drinking water was equivalent to 440–420 μg/g adsorbent. The maximum removal efficiency of Mo by faujasite–phillipsite, phillipsite–chabazite, and the modified surfactant phillipsite–chabazite tuffs were 80%, 76%, and 78%, respectively. The proportional relationship between contact time and removal efficiency of Ni from water samples was observed. The maximum removal efficiency of Ni by the zeolitic tuffs is up to 90% compared to the original groundwater sample.

  10. Comparative study of 99Mo/99mTc generators at base of synthesized gels starting from 99Mo of activation and of fission

    International Nuclear Information System (INIS)

    Lopez M, I.Z.; Monroy G, F.; Rivero G, T.; Rojas N, P.

    2007-01-01

    At the present time the more used and diffused radionuclide in nuclear medicine it is the Technetium 99 metastable ( 99 mTc) it is used for diagnostic and therapy. It is produced starting from molybdenum 99 ( 99 Mo), which is absorbed in chromatographic columns, loaded with alumina that absorb only 0.2% of 99 Mo situation that forces to use high specific activities of 99 Mo that it is obtained starting from the fission of the 235 U. Given these conditions and limitations, new preparation procedures of 99 Mo/ 99m Tc generators, of low or medium specific activity, its have been developed, using gels of zirconium molybdates that incorporates until 30% in weight of 99 Mo in the gel, and also conserve similar characteristics of quality and purity that those obtained by the traditional generator; reducing by this way the cost of production of the 99m Tc, when using 99 Mo of low specific activity, in the preparation of 99 Mo/ 99m Tc generators. The radiochemical characteristics of the elution of 99m Tc, depends strongly on the gel preparation conditions. In particular, the present work has for object to determine the influence of the used type of 99 Mo, fission or activation product, during the gels synthesis, as well as the used air flow for the agitation in the gels preparation and its influence in the quality of the 99 Mo/ 99m Tc generators. When diminishing the agitation air flow the efficiency it increases and in the radionuclide purity of the eluates and when using 99 Mo of fission for the gels production it increases in an important way the elution efficiency, the radiochemical purity and radionuclide of the eluates of 99m Tc. (Author)

  11. Total energy consumption in Finland increased by one percent

    International Nuclear Information System (INIS)

    Timonen, L.

    2000-01-01

    The total energy consumption in Finland increased by less than a percent in 1999. The total energy consumption in 1999 was 1310 PJ corresponding to about 31 million toe. The electric power consumption increased moderately by 1.6%, which is less than the growth of the gross national product (3.5%). The final consumption of energy grew even less, only by 0.5%. Import of electric power increased by 19% in 1999. The import of electric power was due to the availability of low-priced electric power on the Nordic electricity markets. Nuclear power generation increased by 5% and the consumption of wood-based fuels by 3%. The increment of the nuclear power generation increased because of the increased output capacity and good operability of the power plants. Wind power production doubles, but the share of it in the total energy consumption is only about 0.01%. The peat consumption decreased by 12% and the consumption of hydroelectric power by 15%. The decrease in production of hydroelectric power was compensated by an increase import of electric power. The consumption of fossil fuels, coal, oil and natural gas remained nearly the same as in 1998. The gasoline consumption, however, decreased, but the consumption of diesel oil increased due to the increased road transport. The share of the fossil fuels was nearly half of the total energy consumption. The consumption of renewable energy sources remained nearly the same, in 23% if the share of peat is excluded, and in 30% if the share of peat is included. Wood-based fuels are the most significant type of renewable fuels. The share of them in 1999 was over 80% of the total usage of the renewable energy sources. The carbon dioxide emissions in Finland decreased in 1999 by 1.0 million tons. The total carbon dioxide emissions were 56 million tons. The decrease was mainly due to the decrease of the peat consumption. The final consumption of energy increased by 0.5%, being hence about 1019 PJ. Industry is the main consumer of energy

  12. Dipole strength distribution below the giant dipole resonance in {sup 92}Mo, {sup 98}Mo and {sup 100}Mo

    Energy Technology Data Exchange (ETDEWEB)

    Rusev, G.Y.

    2006-07-01

    Investigations of the dipole-strength distributions in {sup 92}Mo, {sup 98}Mo and {sup 100}Mo were carried out by means of the method of nuclear resonance fluorescence. The low-lying excitations in the nuclides {sup 92}Mo, {sup 98}Mo and {sup 100}Mo have been studied in photon-scattering experiments at an electron energy of 6 MeV at the ELBE accelerator and at electron energies from 3.2 to 3.8 MeV at the Dynamitron accelerator. Five levels were observed in {sup 92}Mo. Five levels in {sup 98}Mo and 14 in {sup 100}Mo were identified for the first time in the energy range from 2 to 4 MeV. Dipole-strength distributions up to the neutron-separation energies in the nuclides {sup 92}Mo, {sup 98}Mo and {sup 100}Mo have been investigated at the ELBE accelerator. Because of the possible observation of transitions in the neighboring nuclei produced via ({gamma},n) reaction, additional measurements at electron energies of 8.4 and 7.8 MeV, below the neutron-separation energy, were performed on {sup 98}Mo and {sup 100}Mo, respectively. The number of transitions assigned to {sup 92}Mo, {sup 98}Mo and {sup 100}Mo is 340, 485 and 499, respectively, the main part of them being dipole transitions. Statistical properties of the observed transitions are obtained. The continuum contains the ground-state transitions as well as the branching transitions to the low-lying levels and the subsequent deexcitations of these levels. (orig.)

  13. Wellness, hard to define, reduces trend up to 4 percent.

    Science.gov (United States)

    Nayer, Cyndy; Berger, Jan; Mahoney, Jack

    2010-04-01

    The purpose of this qualitative study was to identify a common language for "wellness" and a correlating health cost trend reduction through incentive-driven prevention and wellness. Mapping the results of the survey with the trend lines reported by innovative employers could uncover increased financial value in health investments. A 10-question survey was designed for telephone interviews with 26 businesses (Innovators) from the Board of the Center for Health Value Innovation; a paper-based survey with the same questions was completed by attendees at a seminar. Then, an online trend survey was conducted with members of the Board (Innovators) to track the total health cost trends in their companies over the past 3-4 years. Responses were compared and analysis of alignment and differences were recorded by graphing. The trend survey results were mapped and tracked with weighted averages. Innovators' responses to the phone survey showed broader definitions of "wellness" than other companies, with little difference in the Innovators' responses when subdivided by size of company. The online trend survey showed that companies that provided incentives for wellness averaged a trend of 4% over the past 3-4 years-approximately 50% of the national trends of 8%-10% over the same time frame. Innovators have defined wellness in ways that would accelerate adoption in the broader business community and drive implementation of wellness programs. The bigger win could be the community-level shift to a culture of health as employees carry these health competencies to the next business in the community.

  14. A Comparison of Perceived and Measured Paternal Weight and BMI, and Relationship to Weight and BMI of his Children

    LENUS (Irish Health Repository)

    Power, RF

    2018-02-01

    Nineteen percent of 9 years old Irish children are overweight; seven percent are obese. Our aims were: to examine whether differences exist between paternal self-reported and measured height, weight and BMI in a population representative sample; and to explore paternal perceptions of their own weight status.\\r\

  15. Electronic structures of B1 MoN, fcc Mo2N, and hexagonal MoN

    International Nuclear Information System (INIS)

    Ihara, H.; Kimura, Y.; Senzaki, K.; Kezuka, H.; Hirabayashi, M.

    1985-01-01

    The electronic structures of B1 MoN, fcc Mo 2 N, and hexagonal MoN were observed by photoelectron spectroscopic measurement. The B1-MoN phase has been predicted to be a high-T/sub c/ superconductor because of a large density of states at Fermi level. The observed electronic structure of the stoichiometric B1-MoN phase is different from that of the real B1-MoN type. The nitrogen excess B1-MoN/sub x/ (x> or =1.3) phase, however, shows the B1-type electronic structure. This is explained by the occurrence of a nitrogen vacancy in the apparent stoichiometric B1 phase and the occupation of the nitrogen vacancy in the nitrogen-excess B1 phase. This property is related to the previously reported low T/sub c/ of the B1-MoN crystals

  16. Impact of Reduced Graphene Oxide on MoS2 Grown by Sulfurization of Sputtered MoO3 and Mo Precursor Films (Postprint)

    Science.gov (United States)

    2016-05-26

    1,2 intercalation assisted exfoliation,8–11 physical vapor deposition (PVD),12,13 and a wet chemistry approach involving thermal decomposition of a... annealed MoO3, MoS2 films S1 (MoS2 using Mo precursor), S2 (MoS2 using MoO3 precursor), S1r (MoS2 using Mo pre- cursor and rGO), and S2r (MoS2 using...MoO3 precursor and rGO). The annealed MoO3 (a) shows Mo(IV) peaks which are indicative of MoO2, and Mo(VI) peaks that occur when MoO3 is present. Both

  17. Weight Loss

    Science.gov (United States)

    ... Rights Employment Discrimination Health Care Professionals Law Enforcement Driver's License For Lawyers Food & Fitness Home Food MyFoodAdvisor ... Fit Types of Activity Weight Loss Assess Your Lifestyle Getting Started Food Choices In My Community Home ...

  18. Bessel Weighted Asymmetries

    Energy Technology Data Exchange (ETDEWEB)

    Avakian, Harut [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Gamberg, Leonard [Pennsylvania State Univ., University Park, PA (United States); Rossi, Patrizia [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Prokudin, Alexei [Pennsylvania State Univ., University Park, PA (United States)

    2016-05-01

    We review the concept of Bessel weighted asymmetries for semi-inclusive deep inelastic scattering and focus on the cross section in Fourier space, conjugate to the outgoing hadron’s transverse momentum, where convolutions of transverse momentum dependent parton distribution functions and fragmentation functions become simple products. Individual asymmetric terms in the cross section can be projected out by means of a generalized set of weights involving Bessel functions. The procedure is applied to studies of the double longitudinal spin asymmetry in semi-inclusive deep inelastic scattering using a new dedicated Monte Carlo generator which includes quark intrinsic transverse momentum within the generalized parton model. We observe a few percent systematic offset of the Bessel-weighted asymmetry obtained from Monte Carlo extraction compared to input model calculations, which is due to the limitations imposed by the energy and momentum conservation at the given energy and hard scale Q2. We find that the Bessel weighting technique provides a powerful and reliable tool to study the Fourier transform of TMDs with controlled systematics due to experimental acceptances and resolutions with different TMD model inputs.

  19. Measurement of target and double-spin asymmetries for the e<mo>→>p<mo>→mo><mo>→mo>eπ<mo>+mo><mo>(n)> reaction in the nucleon resonance region at low Q2

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, X.; Adhikari, K. P.; Bosted, P.; Deur, A.; Drozdov, V.; El Fassi, L.; Kang, Hyekoo; Kovacs, K.; Kuhn, S.; Long, E.; Phillips, S. K.; Ripani, M.; Slifer, K.; Smith, L. C.; Adikaram, D.; Akbar, Z.; Amaryan, M. J.; Anefalos Pereira, S.; Asryan, G.; Avakian, H.; Badui, R. A.; Ball, J.; Baltzell, N. A.; Battaglieri, M.; Batourine, V.; Bedlinskiy, I.; Biselli, A. S.; Briscoe, W. J.; Bültmann, S.; Burkert, V. D.; Carman, D. S.; Celentano, A.; Chandavar, S.; Charles, G.; Chen, J. -P.; Chetry, T.; Choi, Seonho; Ciullo, G.; Clark, L.; Colaneri, L.; Cole, P. L.; Compton, N.; Contalbrigo, M.; Crede, V.; D' Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Djalali, C.; Dodge, G. E.; Dupre, R.; Egiyan, H.; El Alaoui, A.; Elouadrhiri, L.; Eugenio, P.; Fanchini, E.; Fedotov, G.; Fersch, R.; Filippi, A.; Fleming, J. A.; Gevorgyan, N.; Ghandilyan, Y.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Gleason, C.; Golovach, E.; Gothe, R. W.; Griffioen, K. A.; Guidal, M.; Guler, N.; Guo, L.; Hanretty, C.; Harrison, N.; Hattawy, M.; Hicks, K.; Holtrop, M.; Hughes, S. M.; Ilieva, Y.; Ireland, D. G.; Ishkhanov, B. S.; Isupov, E. L.; Jenkins, D.; Jiang, H.; Jo, H. S.; Joosten, S.; Keller, D.; Khachatryan, G.; Khandaker, M.; Kim, A.; Kim, W.; Klein, F. J.; Kubarovsky, V.; Lanza, L.; Lenisa, P.; Livingston, K.; MacGregor, I. J. D.; Markov, N.; McKinnon, B.; Mirazita, M.; Mokeev, V.; Movsisyan, A.; Munevar, E.; Munoz Camacho, C.; Murdoch, G.; Nadel-Turonski, P.; Net, L. A.; Ni, A.; Niccolai, S.; Niculescu, G.; Niculescu, I.; Osipenko, M.; Ostrovidov, A. I.; Paolone, M.; Paremuzyan, R.; Park, K.; Pasyuk, E.; Peng, P.; Pisano, S.; Pogorelko, O.; Price, J. W.; Puckett, A. J. R.; Raue, B. A.; Rizzo, A.; Rosner, G.; Rossi, P.; Roy, P.; Sabatié, F.; Salgado, C.; Schumacher, R. A.; Sharabian, Y. G.; Skorodumina, Iu.; Smith, G. D.; Sokhan, D.; Sparveris, N.; Stankovic, I.; Strakovsky, I. I.; Strauch, S.; Taiuti, M.; Tian, Ye; Ungaro, M.; Voskanyan, H.; Voutier, E.; Walford, N. K.; Watts, D. P.; Wei, X.; Weinstein, L. B.; Wood, M. H.; Zachariou, N.; Zhang, J.; Zonta, I.

    2016-10-01

    We report measurements of target- and double-spin asymmetries for the exclusive channel e<mo>→>p<mo>→mo><mo>→mo>eπ<mo>+mo><mo>(n)> in the nucleon resonance region at Jefferson Lab using the CEBAF Large Acceptance Spectrometer (CLAS). These asymmetries were extracted from data obtained using a longitudinally polarized NH3 target and a longitudinally polarized electron beam with energies 1.1, 1.3, 2.0, 2.3, and 3.0 GeV. The new results are consistent with previous CLAS publications but are extended to a low Q2 range from 0.0065 to 0.35 (GeV/c)2. The Q2 access was made possible by a custom-built Cherenkov detector that allowed the detection of electrons for scattering angles as low as 6 degrees. These results are compared with the unitary isobar models JANR and MAID, the partial-wave analysis prediction from SAID, and the dynamic model DMT. In many kinematic regions our results, in particular results on the target asymmetry, help to constrain the polarization-dependent components of these models.

  20. Development of an aging integrator for uranium-0.75 weight percent titanium alloy part aging control

    International Nuclear Information System (INIS)

    Howington, L.C.

    1977-12-01

    An instrumentation system (Aging Integrator) has been developed to provide more precise control of the heat-treatment process used on uranium-0.75 wt.% titanium alloy material. The Aging Integrator calculates the integral of a predetermined aging function to control the aging period in the heat-treatment process. This control was employed to compensate for discrepancies caused by variations in heatup times, furnace-control fluctuations, and disagreement as to the temperature at which aging actually starts. Although the Aging Integrator hardware has been installed and satisfactorily tested on a production-area furnace, sufficient data to estimate a statistically sound aging integration function will not be available for approximately one year

  1. Melting, casting, and alpha-phase extrusion of the uranium-2.4 weight percent niobium alloy

    International Nuclear Information System (INIS)

    Anderson, R.C.; Beck, D.E.; Kollie, T.G.; Zorinsky, E.J.; Jones, J.M.

    1981-10-01

    The experimental details of the melting, casting, homogenization, and alpha-phase extrusion process used to fabricate the uranium-2.4 wt % niobium alloy into 46-mm-diameter rods is described. Extrusion defects that were detected by an ultrasonic technique were eliminated by proper choice of extrusion parameters; namely, reduction ratio, ram speed, die angle, and billet preheat temperature

  2. Measurement and Estimation of the 99Mo Production Yield by 100Mo(n,2n)99Mo

    Science.gov (United States)

    Minato, Futoshi; Tsukada, Kazuaki; Sato, Nozomi; Watanabe, Satoshi; Saeki, Hideya; Kawabata, Masako; Hashimoto, Shintaro; Nagai, Yasuki

    2017-11-01

    We, for the first time, measured the yield of 99Mo, the mother nuclide of 99mTc used in nuclear medicine diagnostic procedures, produced by the 100Mo(n,2n)99Mo reaction with accelerator neutrons. The neutrons with a continuous energy spectrum from the thermal energy up to about 40 MeV were provided by the C(d,n) reaction with 40 MeV deuteron beams. It was proved that the 99Mo yield agrees with that estimated by using the latest data on neutrons from the C(d,n) reaction and the evaluated cross section of the 100Mo(n,2n)99Mo reaction given in the Japanese Evaluated Nuclear Data Library. On the basis of the agreement, a systematic calculation was carried out to search for an optimum condition that enables us to produce as much 99Mo as possible with a good 99Mo/100Mo value from an economical point of view. The calculated 99Mo yield from a 150 g 100MoO3 sample indicated that about 30% of the demand for 99Mo in Japan can be met with a single accelerator capable of 40 MeV, 2 mA deuteron beams. Here, by referring to an existing 18F-fluorodeoxyglucose (FDG) distribution system we assumed that 99mTc radiopharmaceuticals formed after separating 99mTc from 99Mo can be delivered to hospitals from a radiopharmaceutical company within 6 h. The elution of 99mTc from 99Mo twice a day would meet about 50% of the demand for 99Mo.

  3. Eccentric exercise training as a countermeasure to non-weight-bearing soleus muscle atrophy

    Science.gov (United States)

    Kirby, Christopher R.; Ryan, Mirelle J.; Booth, Frank W.

    1992-01-01

    This investigation tested whether eccentric resistance training could prevent soleus muscle atrophy during non-weight bearing. Adult female rats were randomly assigned to either weight bearing +/- intramuscular electrodes or non-weight bearing +/- intramuscular electrodes groups. Electrically stimulated maximal eccentric contractions were performed on anesthetized animals at 48-h intervals during the 10-day experiment. Non-weight bearing significantly reduced soleus muscle wet weight (28-31 percent) and noncollagenous protein content (30-31 percent) compared with controls. Eccentric exercise training during non-weight bearing attenuated but did not prevent the loss of soleus muscle wet weight and noncollagenous protein by 77 and 44 percent, respectively. The potential of eccentric exercise training as an effective and highly efficient counter-measure to non-weight-bearing atrophy is demonstrated in the 44 percent attenuation of soleus muscle noncollagenous protein loss by eccentric exercise during only 0.035 percent of the total non-weight-bearing time period.

  4. Cyclic Oxidation of High Mo, Reduced Density Superalloys

    Directory of Open Access Journals (Sweden)

    James L. Smialek

    2015-11-01

    Full Text Available Cyclic oxidation was characterized as part of a statistically designed, 12-alloy compositional study of 2nd generation single crystal superalloys as part of a broader study to co-optimize density, creep strength, and cyclic oxidation. The primary modification was a replacement of 5 wt. % W by 7% or 12% Mo for density reductions of 2%–7%. Compositions at two levels of Mo, Cr, Co, and Re were produced, along with a midpoint composition. Initially, polycrystalline vacuum induction samples were screened in 1100 °C cyclic furnace tests using 1 h cycles for 200 h. The behavior was primarily delimited by Cr content, producing final weight changes of −40 mg/cm2 to −10 mg/cm2 for 0% Cr alloys and −2 mg/cm2 to +1 mg/cm2 for 5% Cr alloys. Accordingly, a multiple linear regression fit yielded an equation showing a strong positive Cr effect and lesser negative effects of Co and Mo. The results for 5% Cr alloys compare well to −1 mg/cm2, and +0.5 mg/cm2 for Rene′ N4 and Rene′ N5 (or Rene′ N6, respectively. Scale phases commonly identified were Al2O3, NiAl2O4, NiTa2O6, and NiO, with (Ni,CoMoO4 found only on the least resistant alloys having 0% Cr and 12% Mo. Scale microstructures were complex and reflected variations in the regional spallation history. Large faceted NiO grains and fine NiTa2O6 particles distributed along NiAl2O4 grain boundaries were typical distinctive features. NiMoO4 formation, decomposition, and volatility occurred for a few high Mo compositions. A creep, density, phase stability, and oxidation balanced 5% Cr, 10% Co, 7% Mo, and 3% Re alloy was selected to be taken forward for more extensive evaluations in single crystal form.

  5. VERY HIGH WEIGHT GAIN IN EXCLUSIVELY BREASTFED INFANTS

    DEFF Research Database (Denmark)

    Larsson, Melanie Wange

    , family doctors and at our institute. Breastmilk intake was estimated by weighing (using prefeeding and postfeeding infant weighing) during 2-4 24h periods (Tanita BD 815 MA). Breastmilk macronutrient content was measured by mid-infrared human milk analyzer (Miris AB, Sweden). Results: Case 1: boy, birth...... weight 3.8 kg. Weight-for-age curve in Fig 1. Exclusively breastfed until 5 mo, and stopped breastfeeding at 11 mo. At 5.5 mo milk intake was about 1100 ml (91ml/kg) and milk macronutrient content (4 samples foremilk and 4 hindmilk (g/100 ml)): fat foremilk 0.4-2.1, hindmilk 4.3-6.9, protein foremilk: 0.......6-0.8. Case 2: girl, birth weight 4.45 kg. Weight-for-age curve in Fig 2. Exclusively breastfed until 5 mo Still partially breastfed at last measurement at 8 mo. At 4 mo milk intake was about 1500 ml (128ml/kg) and milk macronutrient content (g/100 ml) measured on 4 complete emptying of a breast: fat 2...

  6. Does Asset Allocation Policy Explain 40, 90, 100 Percent of Performance?

    OpenAIRE

    Roger G. Ibbotson; Paul D. Kaplan

    2001-01-01

    Does asset allocation policy explain 40 percent, 90 percent, or 100 percent of performance? According to some well-known studies, more than 90 percent of the variability of a typical plan sponsor's performance over time is attributable to asset allocation. However, few people want to explain variability over time. Instead, an analyst might want to know how important it is in explaining the differences in return from one fund to another, or what percentage of the level of a typical fund's retu...

  7. 49 CFR 173.182 - Barium azide-50 percent or more water wet.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Barium azide-50 percent or more water wet. 173.182 Section 173.182 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS... Class 1 and Class 7 § 173.182 Barium azide—50 percent or more water wet. Barium azide—50 percent or more...

  8. 7 CFR 762.129 - Percent of guarantee and maximum loss.

    Science.gov (United States)

    2010-01-01

    ... loss. (a) General. The percent of guarantee will not exceed 90 percent based on the credit risk to the lender and the Agency both before and after the transaction. The Agency will determine the percentage of... PLP lenders will not be less than 80 percent. (d) Maximum loss. The maximum amount the Agency will pay...

  9. Fabrication of nanocrystalline alloys Cu–Cr–Mo super satured solid solution by mechanical alloying

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar, C., E-mail: claudio.aguilar@usm.cl [Departamento de Ingeniería Metalúrgica y Materiales, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile); Guzmán, D. [Departamento de Ingeniería en Metalurgia, Facultad de Ingeniería, Universidad de Atacama y Centro Regional de Investigación y Desarrollo Sustentable de Atacama (CRIDESAT), Av. Copayapu 485, Copiapó (Chile); Castro, F.; Martínez, V.; Cuevas, F. de las [Centro de Estudios e Investigaciones Técnicas de Gipuzkoa, Paseo de Manuel Lardizábal, N° 15, 20018 San Sebastián (Spain); Lascano, S. [Departamento de Ingeniería Mecánica, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile); Muthiah, T. [Departamento de Ingeniería Metalúrgica y Materiales, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile)

    2014-08-01

    This work discusses the extension of solid solubility of Cr and Mo in Cu processed by mechanical alloying. Three alloys processed, Cu–5Cr–5Mo, Cu–10Cr–10Mo and Cu–15Cr–15Mo (weight%) using a SPEX mill. Gibbs free energy of mixing values 10, 15 and 20 kJ mol{sup −1} were calculated for these three alloys respectively by using the Miedema's model. The crystallite size decreases and dislocation density increases when the milling time increases, so Gibbs free energy storage in powders increases by the presence of crystalline defects. The energy produced by crystallite boundaries and strain dislocations were estimated and compared with Gibbs free energy of mixing values. The energy storage values by the presence of crystalline defects were higher than Gibbs free energy of mixing at 120 h for Cu–5Cr–5Mo, 130 h for Cu–10Cr–10Mo and 150 h for Cu–15Cr–15Mo. During milling, crystalline defects are produced that increases the Gibbs free energy storage and thus the Gibbs free energy curves are moved upwards and hence the solubility limit changes. Therefore, the three alloys form solid solutions after these milling time, which are supported with the XRD results. - Highlights: • Extension of solid solution Cr and Mo in Cu achieved by mechanical alloying. • X-ray characterization of Cu–Cr–Mo system processed by mechanical alloying. • Thermodynamics analysis of formation of solid solution of the Cu–Cr–Mo system.

  10. Healthy Weight

    Science.gov (United States)

    ... such diets limit your nutritional intake, can be unhealthy, and tend to fail in the long run. The key to achieving and maintaining a healthy weight isn't about short-term dietary changes. It's about a lifestyle that includes healthy eating, regular physical activity, and ...

  11. Weighted approximation with varying weight

    CERN Document Server

    Totik, Vilmos

    1994-01-01

    A new construction is given for approximating a logarithmic potential by a discrete one. This yields a new approach to approximation with weighted polynomials of the form w"n"(" "= uppercase)P"n"(" "= uppercase). The new technique settles several open problems, and it leads to a simple proof for the strong asymptotics on some L p(uppercase) extremal problems on the real line with exponential weights, which, for the case p=2, are equivalent to power- type asymptotics for the leading coefficients of the corresponding orthogonal polynomials. The method is also modified toyield (in a sense) uniformly good approximation on the whole support. This allows one to deduce strong asymptotics in some L p(uppercase) extremal problems with varying weights. Applications are given, relating to fast decreasing polynomials, asymptotic behavior of orthogonal polynomials and multipoint Pade approximation. The approach is potential-theoretic, but the text is self-contained.

  12. Carbonization kinetics of La2O3-Mo cathode materials

    International Nuclear Information System (INIS)

    Jinshu, W.; Meiling, Z.; Tieyong, Z.; Jiuxing, Z.; Zuoren, N.

    2001-01-01

    The carbonization kinetics of La 2 O 3 -Mo cathode materials has been studied by thermal analysis method. Three-stage model of the carbonization has been presented in this paper. The carbonization rate is initially controlled by chemical reaction, then controlled by chemical reaction mixed with diffusion, finally controlled by diffusion. After the initial experimental data are processed according to this model, the correlation coefficients of the kinetic curves are satisfactory. The apparent activation energy of carbonization of La 2 O 3 -Mo cathode materials has been obtained. At the same time, we have deduced the empirical expressions of the amount of weight increased per unit area after carbonization, temperature and time in the temperature range 1393 K - 1493 K. (author)

  13. Effects of HFIR irradiation at 550C on the microstructure and toughness of HT-9 and 9Cr-1Mo

    International Nuclear Information System (INIS)

    Gelles, D.S.; Hu, W.L.; Huang, F.H.; Johnson, G.D.

    1984-01-01

    Results are reported for base metal and weld metal specimens of HT-9 and Modified 9Cr-1Mo following irradiation in HFIR at 55 0 C to 5 dpa. The DBTT shifts in irradiated base metal specimens were 30 0 C for HT-9 and 90 0 C for 9Cr-1Mo with further shifts of 20 0 C for weld metal. Concurrently, strength as measured by hardness increased 15 percent for HT-9 and 25 percent for 9Cr-1Mo. The hardness increases can be attributed in part to defect clusters 1.5 to 3.0 nm in diameter at densities approaching 10 17 cm -3 and also to lower rates of cavity nucleation ahead of the propagating crack

  14. Ternary system of Na2MoO4-Cs2MoO4-MoO3

    International Nuclear Information System (INIS)

    Zueva, V.P.; Shabanova, A.N.; Drobasheva, T.I.

    1982-01-01

    Using the methods of thermal analysis interaction of components in ternary system Na 2 MoO 4 -Cs 2 MoO 4 -MoO 3 has been studied. Crystallization surface consists of nine fields belonging to initial components and compounds of lateral sides. Triangulation of the system is carried out and the character of nonvariant points is clarified, the temperature of 360 deg C corresponds to low-melting eutectics

  15. CRED Cumulative Map of Percent Scleractinian Coral Cover at Kauai, 2005

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  16. CRED Cumulative Map of Percent Scleractinian Coral Cover at Niihau, 2005

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  17. CRED Cumulative Map of Percent Scleractinian Coral Cover at Raita Bank, 2001

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  18. CRED Cumulative Map of Percent Scleractinian Coral Cover at Kure Atoll, 2002-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  19. CRED Cumulative Map of Percent Scleractinian Coral Cover at Stingray Shoals

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  20. CRED Cumulative Map of Percent Scleractinian Coral Cover at Ofu & Olosega

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  1. CRED Cumulative Map of Percent Scleractinian Coral Cover at Laysan Island, 2002-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  2. CRED Cumulative Map of Percent Scleractinian Coral Cover at Eleven-Mile Bank

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  3. CRED Cumulative Map of Percent Scleractinian Coral Cover at Palmyra Atoll, 2002-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  4. CRED Cumulative Map of Percent Scleractinian Coral Cover at Lisianski Island, 2001-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  5. CRED Cumulative Map of Percent Scleractinian Coral Cover at Ta'u

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  6. CRED Cumulative Map of Percent Scleractinian Coral Cover at Gardner Pinnacles, 2003

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  7. CRED Cumulative Map of Percent Scleractinian Coral Cover at Pearl and Hermes Atoll, 2002-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  8. CRED Cumulative Map of Percent Scleractinian Coral Cover at Molokai, 2005

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  9. CRED Cumulative Map of Percent Scleractinian Coral Cover at Guam, 2003

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  10. CRED Cumulative Map of Percent Scleractinian Coral Cover at Baker Island, 2002-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  11. CRED Cumulative Map of Percent Scleractinian Coral Cover at French Frigate Shoals

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  12. CRED Cumulative Map of Percent Scleractinian Coral Cover at Maro Reef, 2001-2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry.

  13. Electronic structure of structural open derivatives of the [Mo6X14]2- cluster: [Mo5Cl13]2- and [Mo4I11]2-

    International Nuclear Information System (INIS)

    Miessner, H.; Korol'kov, D.V.

    1983-01-01

    The electronic structure of structural open derivatives of the [Mo 6 X 14 ] 2 - -cluster [Mo 5 Cl 13 ] 2 - and [Mo 4 I 11 ] 2 - has been studied by the EHMO method. In [Mo 5 Cl 13 ] 2 - 9 occupied MO's with dominant Mo4d character are responsible for the formation of the 8 metal-metal bonds. In [Mo 4 I 11 ] 2 - the stronger covalent character of the Mo-I bonds affects the localization and the energy of molecular orbitals and also the charge distribution. The metal-metal bonds are formed by 8 MO's containing considerable participation of halogen AO's contrary to the chloride cluster. There is no bonding between the Mo atoms at the wing tips of the Mo 4 butterfly and the reason for decreasing the dihedral angle between the Mo 3 planes in [Mo 4 I 11 ] 2 - compared with the octahedral angle is apparently the stabilization of the whole system (Mo-Mo and Mo-I bonds). The unpaired electron occupies in both clusters a slightly antibonding (with regard to the Mo-Mo bonds) orbital. (author)

  14. Creep and shrinkage of Mo(Ni)

    International Nuclear Information System (INIS)

    Kaysser, W.A.; Hofmann-Amtenbrink, M.; Petzow, G.

    1984-01-01

    To avoid some of the errors inherent in a quantitative interpretation of shrinkage of powder compacts as Mo-Ni, other experiments were looked for, where the influence of Ni on the material transport properties of Mo could be measured semi-quantitatively during heating up to temperature and subsequent isothermal annealing. The bending of thin Mo foils under small loads was found to be an experimental arrangement, where variations in stress, in Ni-concentration and in intrinsic material properties could be realized. The results of these creep experiments will be compared in a qualitative sense with sintering experiments in Mo-Ni done under similar conditions as the creep experiments

  15. Associations between human milk oligosaccharides and infant body composition in the first 6 mo of life.

    Science.gov (United States)

    Alderete, Tanya L; Autran, Chloe; Brekke, Benjamin E; Knight, Rob; Bode, Lars; Goran, Michael I; Fields, David A

    2015-12-01

    Evidence linking breastfeeding to reduced risk of developing childhood obesity is inconclusive, yet previous studies have not considered variation in specific components of breast milk that may affect early development. We examined whether differences in the composition of human milk oligosaccharides (HMOs) correlate with infant growth and body composition at 1 and 6 mo of age. Twenty-five mother-infant dyads were recruited from the University Hospital at the University of Oklahoma Health Sciences Center. Infants were breastfed for 6 mo. Breast-milk and infant measures were obtained at 1 and 6 mo of infant age. HMO composition was analyzed by high-pressure liquid chromatography, and infant growth (length and weight) and body composition (percentage fat, total fat, lean mass) were measured by dual-energy X-ray absorptiometry. Relations between HMOs and infant growth and body composition were examined by using multiple linear regression. A priori covariates included maternal prepregnancy body mass index, pregnancy weight gain, and infant age and sex. Higher HMO diversity and evenness at 1 mo were associated with lower total and percentage fat mass at 1 mo. At 1 mo, each 1-μg/mL increase in lacto-N-fucopentaose (LNFP) I was associated with a 0.40-kg lower infant weight (P = 0.03). At 6 mo, each 1-μg/mL increase in LNFPI was associated with a 1.11-kg lower weight (P = 0.03) and a 0.85-g lower lean mass (P = 0.01). At 6 mo, each 1-μg/mL increase in LNFPI was associated with a 0.79-g lower fat mass (P = 0.02), whereas disialyl-lacto-N-tetraose and LNFPII were associated with a 1.92-g (P = 0.02) and 0.42-g (P = 0.02) greater fat mass, respectively. At 6 mo, each 1-μg/mL increase in fucosyl-disialyl-lacto-N-hexaose and lacto-N-neotetraose was associated with 0.04% higher (P = 0.03) and 0.03% lower (P milk are associated with infant growth and body composition. This trial was registered at clinicaltrials.gov as NCT02535637. © 2015 American Society for Nutrition.

  16. On the reduction of orthorhombic MoO3 to MoO2

    International Nuclear Information System (INIS)

    Delannay, F.

    1982-01-01

    Electron diffraction shows evidence of topotactic orientation relationships between the original MoO 3 crystal and MoO 2 crystals formed under mild reduction conditions. These relationships differ from previously published literature data. A possible mechanism of formation of the [100] strings of edge sharing octahedra in the MoO 2 structure is tentatively proposed. (author)

  17. Microwave effects on NiMoS and CoMoS single-sheet catalysts.

    Science.gov (United States)

    Borges, I; Silva, Alexander M; Modesto-Costa, Lucas

    2018-05-04

    Single-sheet nanoclusters of MoS 2 , NiMoS or CoMoS are widely used in hydrodesulfurization (HDS) catalysis in the petroleum industry. In HDS reactions under microwave irradiation, experiments indirectly pointed out that for pristine MoS 2 reaction rates are accelerated because hot spots are generated on the catalyst bed. In this work, we investigated NiMoS and CoMoS isolated single-sheet substituted catalysts before and after thiophene adsorption focusing on quantifying the effect of microwave irradiation. For that purpose, density functional theory (DFT) molecular charge densities of each system were decomposed according to the distributed multipole analysis (DMA) of Stone. Site dipole values of each system were directly associated with a larger or smaller interaction with the microwave field according to a proposed general approach. We showed that microwave enhancement of HDS reaction rates can occur more efficiently in the CoMoS and NiMoS promoted clusters compared to pristine MoS 2 in the following order: CoMoS > NiMoS > MoS 2 . The atomic origin of the catalyst hot spots induced by microwaves was clearly established in the promoted clusters.

  18. Edge termination of MoS2 and CoMoS catalyst particles

    DEFF Research Database (Denmark)

    Byskov, Line Sjolte; Nørskov, Jens Kehlet; Clausen, B. S.

    2000-01-01

    The edge termination of MoS2 and CoMoS catalyst particles is studied by density functional calculations. We show that for structures without vacancies Mo-terminated edges have the lowest edge energies. Creation of vacancies, which are believed to be active sites in these catalyst systems, leads...

  19. Postirradiation tensile properties of Mo and Mo alloys irradiated with 600 MeV protons

    International Nuclear Information System (INIS)

    Mueller, G.V.; Gavillet, D.; Victoria, M.; Martin, J.L.

    1994-01-01

    Tensile specimens of pure Mo and Mo-5 Re, Mo-41 Re and TZM alloys have been irradiated with 600 MeV protons in the PIREX facility at 300 and 660 K to 0.5 dpa. Results of the postirradiation tensile testing show a strong radiation hardening and a severe loss of ductility for all the materials tested at room temperature. ((orig.))

  20. 46 CFR 42.20-7 - Flooding standard: Type “B” vessel, 60 percent reduction.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Flooding standard: Type âBâ vessel, 60 percent reduction... DOMESTIC AND FOREIGN VOYAGES BY SEA Freeboards § 42.20-7 Flooding standard: Type “B” vessel, 60 percent... applied to the following flooding standards: (1) If the vessel is 225 meters (738 feet) or less in length...

  1. Basal area or stocking percent: which works best in controlling density in natural shortleaf pine stands

    Science.gov (United States)

    Ivan L. Sander

    1986-01-01

    Results from a shortleaf pine thinning study in Missouri show that continually thinning a stand to the same basal area will eventually create an understocked stand and reduce yields. Using stocking percent to control thinning intensity allows basal area to increase as stands get older. The best yield should occur when shortleaf pine is repeatedly thinned to 60 percent...

  2. 12 CFR 741.4 - Insurance premium and one percent deposit.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Insurance premium and one percent deposit. 741... Insurance premium and one percent deposit. (a) Scope. This section implements the requirements of Section... payment of an insurance premium. (b) Definitions. For purposes of this section: (1) Available assets ratio...

  3. Preparation, Characterization, and Catalytic Activity of MoCo/USY Catalyst on Hydrodeoxygenation Reaction of Anisole

    Science.gov (United States)

    Nugrahaningtyas, K. D.; Suharbiansah, R. S. R.; Rahmawati, F.

    2018-03-01

    This research aims to prepare, characterize, and study the catalytic activity of Molybdenum (Mo) and Cobalt (Co) metal with supporting material Ultra Stable Y-Zeolite (USY), to produce catalysts with activity in hydrotreatment reaction and in order to eliminate impurities compounds that containing unwanted groups heteroatoms. The bimetallic catalysts MoCo/USY were prepared by wet impregnation method with weight variation of Co metal 0%, 2%, 4%, 6%, 8%, and Mo metal 8% (w/w), respectively. Activation method of the catalyst included calcination, oxidation, reduction and the crystallinity was characterized using X-ray diffraction (XRD), the acidity of the catalyst was analyzed using Fourier Transform Infrared Spectroscopy (FT-IR) and gravimetry method, minerals present in the catalyst was analyzed using X-Ray Fluorescence (XRF), and surface of the catalyst was analyzed using Surface Area Analyzer (SAA). Catalytic activity test (benzene yield product) of MoCo/USY on hydrodeoxigenation reaction of anisole aimed to determine the effect of Mo-Co/USY for catalytic activity in the reaction hydrodeoxigenation (HDO) anisole. Based on characterization and test of catalytic activity, it is known that catalytic of MoCo/USY 2% (catalyst B) shows best activities with acidity of 10.209 mmol/g, specific area of catalyst of 426.295 m2/g, pore average of 14.135 Å, total pore volume 0.318 cc/g, and total yield of HDO products 6.06%.

  4. Spectral characterization of mechanically synthesized MoO3-CuO nanocomposite

    Science.gov (United States)

    Sundeep, Dola; Gopala Krishna, A.; Ravikumar, R. V. S. S. N.; Vijaya Kumar, T.; Daniel Ephraim, S.; Pavan, Y. L.

    2016-01-01

    In this work, MoO3-CuO metal oxide composite nanopowders are prepared by simple mechanochemical assisted synthesis technique with the stoichiometric weight ratios of MoO3 and CuO as 2.3:1 and 3.3:1, respectively. The structural and spectroscopic properties of the as-synthesised samples are characterised by XRD, SEM with EDS, FT-IR, Raman spectroscopy and TGA/DTA. X-ray diffraction pattern demonstrates the peaks correspond to orthorhombic phase of α-MoO3 and monoclinic phase of β-CuO. The average crystalline sizes of the 2.3:1 and 3.3:1 samples were found to be 16 and 24 nm, respectively, which are supported by Williamson-Hall (W-H) calculations. The correlations between the milling rotational speeds with morphological characteristics are revealed by the SEM images. The fundamental modes of Mo=O and Cu-O were analysed by FT-IR. Raman analysis has provided the qualitative information about the structure of the mixed oxide composite. Thermogravimetry analysis and Differential Thermal Analysis (DTA) of MoO3-CuO have revealed that the dual phase mixed oxide composite is stable up to 709 °C with a negligible weight loss. Based on the above, it can be inferred that the synthesised mixed lubricous oxide nanocomposite could be used as a solid lubricant at elevated temperatures.

  5. On the Mo-Papas equation

    Science.gov (United States)

    Aguirregabiria, J. M.; Chamorro, A.; Valle, M. A.

    1982-05-01

    A new heuristic derivation of the Mo-Papas equation for charged particles is given. It is shown that this equation cannot be derived for a point particle by closely following Dirac's classical treatment of the problem. The Mo-Papas theory and the Bonnor-Rowe-Marx variable mass dynamics are not compatible.

  6. Structure and thermal properties of as-fabricated U-7Mo/Mg and U-10Mo/Mg low-enriched uranium research reactor fuels

    Energy Technology Data Exchange (ETDEWEB)

    Kulakov, Mykola, E-mail: mykola.kulakov@cnl.ca [Fuel Development Branch, Canadian Nuclear Laboratories, Chalk River, ON K0J 1J0 Canada (Canada); Saoudi, Mouna [Fuel Development Branch, Canadian Nuclear Laboratories, Chalk River, ON K0J 1J0 Canada (Canada); Piro, Markus H.A. [Fuel and Fuel Channel Safety Branch, Canadian Nuclear Laboratories, Chalk River, ON K0J 1J0 Canada (Canada); Donaberger, Ronald L. [Canadian Neutron Beam Centre, Chalk River, ON K0J 1J0 Canada (Canada)

    2017-02-15

    Aluminum-clad U-7Mo/Mg and U-10Mo/Mg pin-type mini-elements (with a core uranium loading of 4.5 gU/cm{sup 3}) have been fabricated at the Canadian Nuclear Laboratories for experimental tests and ultimately for use in research and test reactors. In this study, the microstructure and phase composition of unirradiated U-7Mo/Mg and U-10Mo/Mg fuel cores were analyzed using optical and scanning electron microscopy, and neutron powder diffraction. Thermal properties were characterized using a combination of experimental measurements and thermodynamic calculations. The thermal diffusivity was measured using the laser flash method. The temperature-dependent specific heat capacities were calculated based on the linear rule of mixture using the weight fraction of different crystalline phases and their specific heat capacity values taken from the literature. The thermal conductivity was then calculated using the measured thermal diffusivity, the measured density and the calculated specific heat capacity. The resulting thermal conductivity is practically identical for both types of fuel. The in-reactor temperatures were predicted using conjugate heat transfer simulations. - Highlights: • Neutron diffraction analysis shows that most of the γ-U(Mo) phase was retained in as-fabricated U-7Mo/Mg and U-10Mo/Mg fuel cores. • The experimental thermal conductivity of both types of fuel is practically identical. • Based on conjugate heat transfer simulations, under normal operating conditions, the in-reactor fuel centreline temperature is about 510 K.

  7. How do pregnancy-related weight changes and breastfeeding relate to maternal weight and BMI-adjusted waist circumference 7 y after delivery?

    DEFF Research Database (Denmark)

    Kirkegaard, Helene; Stovring, Henrik; Rasmussen, Kathleen M

    2014-01-01

    of breastfeeding are unknown. OBJECTIVE: The objective was to examine how prepregnancy weight, gestational weight gain, postpartum weight changes, and breastfeeding influence maternal weight and body mass index-adjusted waist circumference (WCBMI) 7 y after delivery. DESIGN: This was a prospective cohort study......; 87% of this effect was mediated through later weight changes. For both outcomes, a small inverse association was observed for breastfeeding duration. This was strongest for WCBMI, for which 97% of the effect was direct, ie, not mediated through postpartum weight. CONCLUSIONS: These findings show...... that postpartum weight retention at 6 mo and weight gain from 6 to 18 mo postpartum contribute equally to adverse maternal anthropometric measures 7 y after delivery. Breastfeeding duration may have a beneficial effect....

  8. Mo(ve)ment-methodology

    DEFF Research Database (Denmark)

    Mørck, Line Lerche; Christian Celosse-Andersen, Martin

    2018-01-01

    This paper describes the theoretical basis for and development of a moment-movement research methodology, based on an integration of critical psychological practice research and critical ethnographic social practice theory. Central theoretical conceptualizations, such as human agency, life...... conditions and identity formation, are discussed in relation to criminological theories of gang desistance. The paper illustrates how the mo(ve)ment methodology was applied in a study of comprehensive processes of identity (re)formation and gang exit processes. This study was conducted with Martin, a former....... This is a moment which captures Martin’s complex and ambiguous feelings of conflictual concerns, frustration, anger, and a new feeling of insecurity in his masculinity, as well as engagement and a sense of deep meaningfulness as he becomes a more reflective academic. All these conflicting feelings also give...

  9. Development of fission Mo-99 production technology

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Ho; Choung, W. M.; Lee, K. I. and others

    2000-05-01

    Fission Mo-99 is the only parent nuclide of Tc-99m, an extremely useful tool for mdeical diagnosis, with an estimated usage of greater than 80% of nuclear medicine applicatons. HEU and LEU targets to optimize in HANARO irradiation condition suggested and designed for domestic production of fission Mo-99. The optimum process conditions are established in each unit process to meet quality requirements of fission Mo-99 products, and the results of performance test in combined process show Mo separation and purification yield of the above 97%. The concept of Tc generator production process is established, and the result of performance test show Tc production yield of 98.4% in Tc generator procuction process. The drafts is prepared for cooperation of technical cooperation and business investment with foreign country. Evaluation on economic feasibility is accompanied for fission Mo-99 and Tc-99m generator production.

  10. Development of fission Mo-99 production technology

    International Nuclear Information System (INIS)

    Park, Jin Ho; Choung, W. M.; Lee, K. I. and others

    2000-05-01

    Fission Mo-99 is the only parent nuclide of Tc-99m, an extremely useful tool for mdeical diagnosis, with an estimated usage of greater than 80% of nuclear medicine applicatons. HEU and LEU targets to optimize in HANARO irradiation condition suggested and designed for domestic production of fission Mo-99. The optimum process conditions are established in each unit process to meet quality requirements of fission Mo-99 products, and the results of performance test in combined process show Mo separation and purification yield of the above 97%. The concept of Tc generator production process is established, and the result of performance test show Tc production yield of 98.4% in Tc generator procuction process. The drafts is prepared for cooperation of technical cooperation and business investment with foreign country. Evaluation on economic feasibility is accompanied for fission Mo-99 and Tc-99m generator production

  11. Solution chemistry of Mo(III) and Mo(IV): Thermodynamic foundation for modeling localized corrosion

    International Nuclear Information System (INIS)

    Wang Peiming; Wilson, Leslie L.; Wesolowski, David J.; Rosenqvist, Joergen; Anderko, Andrzej

    2010-01-01

    To investigate the behavior of molybdenum dissolution products in systems that approximate localized corrosion environments, solubility of Mo(III) in equilibrium with solid MoO 2 has been determined at 80 deg. C as a function of solution acidity, chloride concentration and partial pressure of hydrogen. The measurements indicate a strong increase in solubility with acidity and chloride concentration and a weak effect of hydrogen partial pressure. The obtained results have been combined with literature data for systems containing Mo(III), Mo(IV), and Mo(VI) in solutions to develop a comprehensive thermodynamic model of aqueous molybdenum chemistry. The model is based on a previously developed framework for simulating the properties of electrolyte systems ranging from infinite dilution to solid saturation or fused salt limit. To reproduce the measurements, the model assumes the presence of a chloride complex of Mo(III) (i.e., MoCl 2+ ) and hydrolyzed species (MoOH 2+ , Mo(OH) 2 + , and Mo(OH) 3 0 ) in addition to the Mo 3+ ion. The model generally reproduces the experimental data within experimental scattering and provides a tool for predicting the phase behavior and speciation in complex, concentrated aqueous solutions. Thus, it provides a foundation for simulating the behavior of molybdenum species in localized corrosion environments.

  12. Spent 99Mo/99mTc generator as an economical source of 99Mo

    International Nuclear Information System (INIS)

    El-Kolaly, M.T.

    1990-01-01

    An improved method for utilization and purification of 99 Mo from spent 90 Mo/ 99m Tc generators has been described. After washing the generator with saline to remove the generated 99m Tc, followed by 2 mL 5 M NaOH containing a few drops of H 2 O 2 , the 99 Mo was quantitatively eluted from the generator with 5 mL 5 M NaOH. The alkaline eluate containing 99 Mo was contaminated with partially dissolved alumina. In the present method, an anion-exchange resin Dowex 1 x 8 column was used for purification of 99 Mo from the contaminating alumina. The resultant 99 Mo was of high purity and contained 3+ /mL 99 Mo solution, as estimated by atomic absorption. (author)

  13. Interdiffusion among U-Mo-Zr and alloys of Al to 550oC

    International Nuclear Information System (INIS)

    Komar Varela, C.L; Arico, S.F; Gribaudo, L.M

    2006-01-01

    The international community, by means of the project 'Reduced Enrichment for Research and Test Reactors' is interested in the development of a new nuclear fuel of very high density of uranium and low enrichment (≤ 20% de U 235 ) for reactors of investigation and production of radioisotopes, that permit to reach greater neutron flows, with good capacity to be reprocessed One of these assemblies are the alloys of U with Mo contents between 7 and 10% in weight. In the fuels 'dispersed type plate' the particles of U-Mo are mixed with dust of aluminum and are co - laminated between two plates of an alloy of the same material. The existing contact among the particles permits the interdiffusion of the materials with the consequent apparition of new phases. Studies pursuit-irradiation have shown a badly behavior of these new phases. It is for this that is necessary to control the presence of these products of interaction. The aggregate of a third element to the alloys U - Mo has begun to be practiced with this purpose. In this work the modification of the start of the disorder of the phase γU in the alloy U-7%Mo-1%Zr was studied and the interdiffusion between pure aluminum and the same alloy to 550 o C. The results obtained are compared with other obtained for peers U-Mo/Al. The techniques of characterization utilized were: optical microscopy, analysis by diffraction of X-rays and microanalysis quantitative by microprobe electronic. It was observed that the aggregate of Zr refines the grain for a processing of homogenized in composition of Mo to 1000 o C and accelerates the start of the disorder of the phase γU to 550 o C. As for the zone of interaction, was found that the composed identifying do not they differ to them reported in the in peers U-Mo/Al. These are: (U,Mo)Al 4 y UAl 3 (AG)

  14. Phase formation in Na2MoO4 - MgMoO4 - Cr2(MoO4)3 system

    International Nuclear Information System (INIS)

    Kotova, I.Yu.; Kozhevnikova, N.M.

    1998-01-01

    Interaction within Na 2 MoO 4 - MgMoO 4 - Cr 2 (MoO 4 ) 3 ternary system is studied by X ray phase and DTA methods. State diagram of NaCr(MoO 4 ) 2 - MgMoO 4 section is plotted. Production of ternary molybdates of Na 1-x Mg 1-x Cr 1+x (MoO 4 ) 3 , where 0 ≤ x ≤ 0.3, and NaMg 3 Cr(MoO 4 ) 5 composition is ascertained [ru

  15. AMORE Mo-99 Spike Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Youker, Amanda J. [Argonne National Lab. (ANL), Argonne, IL (United States); Krebs, John F. [Argonne National Lab. (ANL), Argonne, IL (United States); Quigley, Kevin J. [Argonne National Lab. (ANL), Argonne, IL (United States); Byrnes, James P. [Argonne National Lab. (ANL), Argonne, IL (United States); Rotsch, David A [Argonne National Lab. (ANL), Argonne, IL (United States); Brossard, Thomas [Argonne National Lab. (ANL), Argonne, IL (United States); Wesolowski, Kenneth [Argonne National Lab. (ANL), Argonne, IL (United States); Alford, Kurt [Argonne National Lab. (ANL), Argonne, IL (United States); Chemerisov, Sergey [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-09-27

    With funding from the National Nuclear Security Administrations Material Management and Minimization Office, Argonne National Laboratory (Argonne) is providing technical assistance to help accelerate the U.S. production of Mo-99 using a non-highly enriched uranium (non-HEU) source. A potential Mo-99 production pathway is by accelerator-initiated fissioning in a subcritical uranyl sulfate solution containing low enriched uranium (LEU). As part of the Argonne development effort, we are undertaking the AMORE (Argonne Molybdenum Research Experiment) project, which is essentially a pilot facility for all phases of Mo-99 production, recovery, and purification. Production of Mo-99 and other fission products in the subcritical target solution is initiated by putting an electron beam on a depleted uranium (DU) target; the fast neutrons produced in the DU target are thermalized and lead to fissioning of U-235. At the end of irradiation, Mo is recovered from the target solution and separated from uranium and most of the fission products by using a titania column. The Mo is stripped from the column with an alkaline solution. After acidification of the Mo product solution from the recovery column, the Mo is concentrated (and further purified) in a second titania column. The strip solution from the concentration column is then purified with the LEU Modified Cintichem process. A full description of the process can be found elsewhere [1–3]. The initial commissioning steps for the AMORE project include performing a Mo-99 spike test with pH 1 sulfuric acid in the target vessel without a beam on the target to demonstrate the initial Mo separation-and-recovery process, followed by the concentration column process. All glovebox operations were tested with cold solutions prior to performing the Mo-99 spike tests. Two Mo-99 spike tests with pH 1 sulfuric acid have been performed to date. Figure 1 shows the flow diagram for the remotely operated Mo-recovery system for the AMORE project

  16. Overweight, Obesity, and Weight Loss

    Science.gov (United States)

    ... Back to section menu Healthy Weight Weight and obesity Underweight Weight, fertility, and pregnancy Weight loss and ... section Home Healthy Weight Healthy Weight Weight and obesity Underweight Weight, fertility, and pregnancy Weight loss and ...

  17. Oxygen Passivation Mediated Tunability of Trion and Excitons in MoS2

    KAUST Repository

    Gogoi, Pranjal Kumar

    2017-08-17

    Using wide spectral range in situ spectroscopic ellipsometry with systematic ultrahigh vacuum annealing and in situ exposure to oxygen, we report the complex dielectric function of MoS2 isolating the environmental effects and revealing the crucial role of unpassivated and passivated sulphur vacancies. The spectral weights of the A (1.92 eV) and B (2.02 eV) exciton peaks in the dielectric function reduce significantly upon annealing, accompanied by spectral weight transfer in a broad energy range. Interestingly, the original spectral weights are recovered upon controlled oxygen exposure. This tunability of the excitonic effects is likely due to passivation and reemergence of the gap states in the band structure during oxygen adsorption and desorption, respectively, as indicated by ab initio density functional theory calculation results. This Letter unravels and emphasizes the important role of adsorbed oxygen in the optical spectra and many-body interactions of MoS2.

  18. Oxygen Passivation Mediated Tunability of Trion and Excitons in MoS2

    KAUST Repository

    Gogoi, Pranjal Kumar; Hu, Zhenliang; Wang, Qixing; Carvalho, Alexandra; Schmidt, Daniel; Yin, Xinmao; Chang, Yung-Huang; Li, Lain-Jong; Sow, Chorng Haur; Neto, A.  H. Castro; Breese, Mark B.  H.; Rusydi, Andrivo; Wee, Andrew T.  S.

    2017-01-01

    Using wide spectral range in situ spectroscopic ellipsometry with systematic ultrahigh vacuum annealing and in situ exposure to oxygen, we report the complex dielectric function of MoS2 isolating the environmental effects and revealing the crucial role of unpassivated and passivated sulphur vacancies. The spectral weights of the A (1.92 eV) and B (2.02 eV) exciton peaks in the dielectric function reduce significantly upon annealing, accompanied by spectral weight transfer in a broad energy range. Interestingly, the original spectral weights are recovered upon controlled oxygen exposure. This tunability of the excitonic effects is likely due to passivation and reemergence of the gap states in the band structure during oxygen adsorption and desorption, respectively, as indicated by ab initio density functional theory calculation results. This Letter unravels and emphasizes the important role of adsorbed oxygen in the optical spectra and many-body interactions of MoS2.

  19. Oxygen Passivation Mediated Tunability of Trion and Excitons in MoS2

    Science.gov (United States)

    Gogoi, Pranjal Kumar; Hu, Zhenliang; Wang, Qixing; Carvalho, Alexandra; Schmidt, Daniel; Yin, Xinmao; Chang, Yung-Huang; Li, Lain-Jong; Sow, Chorng Haur; Neto, A. H. Castro; Breese, Mark B. H.; Rusydi, Andrivo; Wee, Andrew T. S.

    2017-08-01

    Using wide spectral range in situ spectroscopic ellipsometry with systematic ultrahigh vacuum annealing and in situ exposure to oxygen, we report the complex dielectric function of MoS2 isolating the environmental effects and revealing the crucial role of unpassivated and passivated sulphur vacancies. The spectral weights of the A (1.92 eV) and B (2.02 eV) exciton peaks in the dielectric function reduce significantly upon annealing, accompanied by spectral weight transfer in a broad energy range. Interestingly, the original spectral weights are recovered upon controlled oxygen exposure. This tunability of the excitonic effects is likely due to passivation and reemergence of the gap states in the band structure during oxygen adsorption and desorption, respectively, as indicated by ab initio density functional theory calculation results. This Letter unravels and emphasizes the important role of adsorbed oxygen in the optical spectra and many-body interactions of MoS2 .

  20. EnviroAtlas - Minneapolis/St. Paul, MN - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  1. EnviroAtlas - Green Bay, WI - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  2. EnviroAtlas - Cleveland, OH - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  3. EnviroAtlas - Austin, TX - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  4. EnviroAtlas - New York, NY - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  5. EnviroAtlas - New Bedford, MA - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  6. EnviroAtlas - Portland, ME - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  7. EnviroAtlas - Woodbine, IA - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  8. EnviroAtlas - Milwaukee, WI - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  9. EnviroAtlas - Tampa, FL - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  10. EnviroAtlas - Pittsburgh, PA - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  11. EnviroAtlas - Phoenix, AZ - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  12. EnviroAtlas - Durham, NC - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  13. EnviroAtlas - Portland, OR - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  14. EnviroAtlas - Paterson, NJ - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  15. EnviroAtlas - Memphis, TN - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  16. EnviroAtlas - Fresno, CA - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  17. EnviroAtlas - Percent Urban Land Cover by 12-Digit HUC for the Conterminous United States

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates the percent urban land for each 12-digit hydrologic unit code (HUC) in the conterminous United States. For the purposes of this...

  18. EnviroAtlas - Des Moines, IA - Estimated Percent Tree Cover Along Walkable Roads

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  19. EnviroAtlas Estimated Percent Tree Cover Along Walkable Roads Web Service

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

  20. 64 Percent of Asian and Pacific Islander Treatment Admissions Name Alcohol as Their Problem

    Science.gov (United States)

    Data Spotlight May 28, 2013 64 Percent of Asian and Pacific Islander Treatment Admissions Name Alcohol as ... common problem in the United States. 1 When Asians and Pacific Islanders (APIs) go to treatment, alcohol ...

  1. Map of percent scleractinian coral cover and sand along camera tow tracks in west Hawaii

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral and sand overlaid on bathymetry and landsat imagery northwest...

  2. Development of fission Mo-99 production technology

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Ho; Choung, W. M.; Lee, K. I. and others

    2001-05-01

    This R and D project is planed to supply domestic demands of Mo-99 through fission route, and consequently this project will be expected to rise up utilization of HANARO and KAERI's capability for marketing extension into domestic and oversea radiopharmaceutical market. HEU and LEU target types are decided and designed for fission Mo-99 production in domestic. Experimental study of target fabrication technology was performed and developed processing equipments. And conceptual design of target loading/unloading in/from HANARO device are performed. Tracer test of Mo-99 separation and purification process was performed, test results reach to Mo-99 recovery yield above 80% and decontamination factor above 1600. Combined Mo-99 separation and purification process was decided for hot test scheduled from next year, and performance test was performed. Conceptual design for modification of existing hot cell for fission Mo-99 production facility was performed and will be used for detail design. Assumption for the comparison of LEU and HEU target in fission Mo-99 production process were suggested and compared of merits and demerits in view of fabrication technology and economy feasibility.

  3. Development of fission Mo-99 production technology

    International Nuclear Information System (INIS)

    Park, Jin Ho; Choung, W. M.; Lee, K. I. and others

    2001-05-01

    This R and D project is planed to supply domestic demands of Mo-99 through fission route, and consequently this project will be expected to rise up utilization of HANARO and KAERI's capability for marketing extension into domestic and oversea radiopharmaceutical market. HEU and LEU target types are decided and designed for fission Mo-99 production in domestic. Experimental study of target fabrication technology was performed and developed processing equipments. And conceptual design of target loading/unloading in/from HANARO device are performed. Tracer test of Mo-99 separation and purification process was performed, test results reach to Mo-99 recovery yield above 80% and decontamination factor above 1600. Combined Mo-99 separation and purification process was decided for hot test scheduled from next year, and performance test was performed. Conceptual design for modification of existing hot cell for fission Mo-99 production facility was performed and will be used for detail design. Assumption for the comparison of LEU and HEU target in fission Mo-99 production process were suggested and compared of merits and demerits in view of fabrication technology and economy feasibility

  4. WHK Student Internship Enrollment, Mentor Participation Up More than 50 Percent | Poster

    Science.gov (United States)

    By Nancy Parrish, Staff Writer The Werner H. Kirsten Student Internship Program (WHK SIP) has enrolled the largest class ever for the 2013–2014 academic year, with 66 students and 50 mentors. This enrollment reflects a 53 percent increase in students and a 56 percent increase in mentors, compared to 2012–2013 (43 students and 32 mentors), according to Julie Hartman, WHK SIP

  5. Experience with high percent step load decrease from full power in NPP Krsko

    International Nuclear Information System (INIS)

    Vukovic, V.

    2000-01-01

    The control system of NPP Kriko, is designed to automatically control the reactor in the power range between 15 and 100 percent of rated power for the following designed transients; - 10 percent step change in load; 5 percent per minute loading and unloading; step full load decrease with the aid of automatically initiated and controlled steam dump. Because station operation below 15 percent of rated power is designed for a period of time during startup or standby conditions, automatic control below 15 percent is not provided. The steam dump accomplishes the following functional tasks: it permits the nuclear plants to accept a sudden 95 percent loss of load without incurring reactor trip; it removes stored energy and residual heat following a reactor trip and brings the plant to equilibrium no-load conditions without actuation of the steam generator safety valves; it permits control of the steam generator pressure at no-load conditions and permits a manually controlled cooldown of the plant. The first two functional tasks are controlled by Tavg. The third is controlled by steam pressure. Interlocks minimise any possibility of an inadvertent actuation of steam dump system. This paper discusses relationships between designed (described) characteristics of plant and the data which are obtained during startup and/or first ten years of operation. (author)

  6. United States home births increase 20 percent from 2004 to 2008.

    Science.gov (United States)

    MacDorman, Marian F; Declercq, Eugene; Mathews, T J

    2011-09-01

    After a gradual decline from 1990 to 2004, the percentage of births occurring at home increased from 2004 to 2008 in the United States. The objective of this report was to examine the recent increase in home births and the factors associated with this increase from 2004 to 2008. United States birth certificate data on home births were analyzed by maternal demographic and medical characteristics. In 2008, there were 28,357 home births in the United States. From 2004 to 2008, the percentage of births occurring at home increased by 20 percent from 0.56 percent to 0.67 percent of United States births. This rise was largely driven by a 28 percent increase in the percentage of home births for non-Hispanic white women, for whom more than 1 percent of births occur at home. At the same time, the risk profile for home births has been lowered, with substantial drops in the percentage of home births of infants who are born preterm or at low birthweight, and declines in the percentage of home births that occur to teen and unmarried mothers. Twenty-seven states had statistically significant increases in the percentage of home births from 2004 to 2008; only four states had declines. The 20 percent increase in United States home births from 2004 to 2008 is a notable development that will be of interest to practitioners and policymakers. (BIRTH 38:3 September 2011). © 2011, Copyright the Authors. Journal compilation © 2011, Wiley Periodicals, Inc.

  7. Mass spectrometric determination of stability of gaseous BaMoO2, Ba2MoO4, Ba2MoO5, Ba2Mo2O8 molecules

    International Nuclear Information System (INIS)

    Kudin, L.S.; Balduchchi, Dzh.; Dzhil'i, G.; Gvido, M.

    1982-01-01

    During the mass spectrometric investigation of BaCrO 4 evaporation Cr + , Ba + , BaO + main ions are recorded as well as BaMoO 4 + , BaMoO 3 + , BaMoO 2 + , BaMoO + , BaMoO 4 + , Ba 2 MoO 5 + , BaMo 2 O 8 + ions - the products of ionization of three-component (Ba, Mo, M) molecules, forming as a result of substance chemical interaction with the material of an effusion cell (Mo). Heats of formation of BaMoO 2 , Ba 2 MoO 4 , Ba 2 MoO 5 and Ba 2 Mo 2 O 8 molecules which constituted - 577+-70, -1343+-115, -1464+-70, -2393+-90 k J/mol respectively are determined on the base of the analysis of curves of ionisation efficiency and of reaction heats Ba 2 MoO 5 =BaO+BaMoO 4 , ΔH 0 0 =322+-60 kJ/mol Ba 2 Mo 2 O 8 =2BaMoO 4 , ΔH 0 0 =351+-80 kJ/mol calculated with the use of third low of thermodynamics [ru

  8. Weight Loss Surgery

    Science.gov (United States)

    Weight loss surgery helps people with extreme obesity to lose weight. It may be an option if you cannot lose weight ... obesity. There are different types of weight loss surgery. They often limit the amount of food you ...

  9. Extended analysis of Mo VI

    International Nuclear Information System (INIS)

    Edlen, B.; Rahimullah, K.; Tauheed, A.; Chaghtai, M.S.Z.

    1985-01-01

    The analysis of the RbI-like spectrum Mo VI has been extended to include a total of some 110 classified lines and 44 energy levels belonging to the one-electron configurations 4s 2 4p 6 ( 1 S)nl with n ranging up to 9 and l up to 7. The analysis is based on recordings of vacuum spark spectra made at Lund in the region 230-2350 A, complemented by a list of lines from 2193 to 6336 A observed and identified by Romanov and Striganov in a Penning type arc discharge. The one-electron level system is partly mixed with core-excited configurations, not treated in the present paper. Especially the nf series is strongly perturbed by 4s 2 4p 5 4d 2 , and an anomalous behaviour of the ng series is explained by interaction with the 2 G term of 4s4p 6 4d 2 . The ionization limit, derived from 6h, 7i and 8k by means of the polarization formula, is found to be 555 132+-2 cm -1 . (orig.)

  10. Magnetism and superconductivity in Eu(Ho)Mo/sub 6/S/sub 8/

    Energy Technology Data Exchange (ETDEWEB)

    Capone, D.W. II; Lai Fook, M.S.; Guertin, R.P.; Hinks, D.G.; Dunlap, B.D.; Foner, S.; Abou-Aly, A.I.; Brooks, J.S.

    1984-10-01

    A variety of ambient and high pressure experimental results reveal the interplay between magnetism and superconductivity in Ho doped samples of the pressure induced superconductor, EuMo/sub 6/S/sub 8/. Ho concentrations up to 50 atomic percent of the rare earth ions were used. High resolution magnetic measurements are consistent with the crystalline electric field ground state for the Ho/sup 3 +/ ions being a magnetic doublet consisting largely of J/sub z/ = 18. The results of high pressure magnetization experiments reveal negligible effects of reduced lattice constant on the rare earth-rare earth interactions. Resistivity in a 10 atomic percent sample for P = 10 kbar shows the suppression of a P = 0 structural transition, metallic conductivity down to low temperatures, and finally superconductivity at 8 K. The upper critical field, H/sub c2/(T), for this sample was measured for P = 7, 10 and 12 kbar and showed strong reentrant behavior (dH/sub c2/(T)/dT > 0 as T ..-->.. 0 K). A minimum with field in the resistivity above H/sub c2/ was also observed at lowest temperatures. The H/sub c2/(T) data are compared with those of EuMo/sub 6/S/sub 8/ at high pressure, which shows positive curvature, and HoMo/sub 6/S/sub 8/, in which superconductivity is quenched by ferromagnetism at low temperatures. 14 references, 4 figures.

  11. Magnetism and superconductivity in Eu(Ho)Mo6S8

    International Nuclear Information System (INIS)

    Capone, D.W. II; Lai Fook, M.S.; Guertin, R.P.; Hinks, D.G.; Dunlap, B.D.; Foner, S.; Abou-Aly, A.I.; Brooks, J.S.

    1984-10-01

    A variety of ambient and high pressure experimental results reveal the interplay between magnetism and superconductivity in Ho doped samples of the pressure induced superconductor, EuMo 6 S 8 . Ho concentrations up to 50 atomic percent of the rare earth ions were used. High resolution magnetic measurements are consistent with the crystalline electric field ground state for the Ho 3+ ions being a magnetic doublet consisting largely of J/sub z/ = 18. The results of high pressure magnetization experiments reveal negligible effects of reduced lattice constant on the rare earth-rare earth interactions. Resistivity in a 10 atomic percent sample for P = 10 kbar shows the suppression of a P = 0 structural transition, metallic conductivity down to low temperatures, and finally superconductivity at 8 K. The upper critical field, H/sub c2/(T), for this sample was measured for P = 7, 10 and 12 kbar and showed strong reentrant behavior (dH/sub c2/(T)/dT > 0 as T → 0 K). A minimum with field in the resistivity above H/sub c2/ was also observed at lowest temperatures. The H/sub c2/(T) data are compared with those of EuMo 6 S 8 at high pressure, which shows positive curvature, and HoMo 6 S 8 , in which superconductivity is quenched by ferromagnetism at low temperatures. 14 references, 4 figures

  12. Nanoparticles of superconducting γ-Mo2N and δ-MoN

    International Nuclear Information System (INIS)

    Gomathi, A.; Sundaresan, A.; Rao, C.N.R.

    2007-01-01

    We have been able to prepare nanoparticles (∼4 nm diameter) of cubic γ-Mo 2 N by a simple procedure involving the reaction of MoCl 5 with urea at 873 K. The nanoparticles show a superconducting transition around 6.5 K. The γ-Mo 2 N nanoparticles are readily transformed to nanoparticles of δ-MoN with a slightly larger diameter on heating in a NH 3 atmosphere at 573 K. Phase-pure δ-MoN obtained by this means shows a superconducting transition around 5 K. - Graphical abstract: TEM image of the γ-Mo 2 N particles with the inset showing the resistivity of the sample as a function of temperature

  13. Stacking change in MoS2 bilayers induced by interstitial Mo impurities.

    Science.gov (United States)

    Cortés, Natalia; Rosales, Luis; Orellana, Pedro A; Ayuela, Andrés; González, Jhon W

    2018-02-01

    We use a theoretical approach to reveal the electronic and structural properties of molybdenum impurities between MoS 2 bilayers. We find that interstitial Mo impurities are able to reverse the well-known stability order of the pristine bilayer, because the most stable form of stacking changes from AA' (undoped) into AB' (doped). The occurrence of Mo impurities in different positions shows their split electronic levels in the energy gap, following octahedral and tetrahedral crystal fields. The energy stability is related to the accommodation of Mo impurities compacted in hollow sites between layers. Other less stable configurations for Mo dopants have larger interlayer distances and band gaps than those for the most stable stacking. Our findings suggest possible applications such as exciton trapping in layers around impurities, and the control of bilayer stacking by Mo impurities in the growth process.

  14. Teammates and social influence affect weight loss outcomes in a team-based weight loss competition.

    Science.gov (United States)

    Leahey, Tricia M; Kumar, Rajiv; Weinberg, Brad M; Wing, Rena R

    2012-07-01

    Team-based internet interventions are increasing in popularity as a way of promoting weight loss in large numbers of individuals. Given that social networks influence health behavior change, this study investigated the effects of teammates and social influence on individual weight loss during a team-based weight loss competition. Shape Up Rhode Island (SURI) 2009 was a 12-week online program open to adult residents of Rhode Island. Participants joined with a team and competed with other teams on weight loss and/or physical activity. Overweight/obese (OW/OB) individuals (N = 3,330; 76% female; age = 46.1 ± 10.8; BMI = 31.2 ± 5.3 kg/m(2)), representing 987 teams, completed the weight loss program. Multilevel modeling was used to examine whether weight loss clustered among teammates and whether percentage of teammates in the weight loss division and reported teammate influence on weight loss were associated with individual weight outcomes. OW/OB completers reported losing 4.2 ± 3.4% of initial body weight. Weight loss was similar among teammates (intraclass correlation coefficient (ICC) = 0.10, P social influence for weight loss were associated with greater percent weight loss (P's ≤ 0.002). Similarly, achieving a clinically significant (5%) weight loss tended to cluster within teams (ICC = 0.09; P social influence for weight loss were associated with increased likelihood of achieving a 5% weight loss (odds ratio (OR) = 1.06; OR = 1.20, respectively). These results suggest that teammates affect weight loss outcomes during a team-based intervention. Harnessing and maximizing teammate influence for weight loss may enhance weight outcomes in large-scale team-based programs.

  15. Maternal concern about child weight in a study of weight-discordant siblings.

    Science.gov (United States)

    Kral, Tanja V E; Moore, Reneé H; Compher, Charlene W

    2015-01-01

    This study examined concern about child weight in mothers of weight-discordant siblings and determined the accuracy of maternal self-report versus measured child height, weight, and corresponding body mass index (BMI; kg/m(2) ) z-score. Discordant sibling design. Forty-seven mothers of 5- to 12-year-old, weight-discordant siblings. Mothers self-reported their concern about child weight for each child separately and for a subset of children, self-reported their heights and weights. Siblings' height, weight, waist circumference, and adiposity were measured. The majority (83%) of mothers expressed concern about their overweight/obese child's weight and 20% of mothers expressed concern about their normal-weight child's weight (p concern about child weight were positively associated with difference scores in sibling BMI z-score (r = 0.42; p = .01) and percent body fat (r = 0.56; p concern for their overweight/obese child's weight was greater for sibling pairs who were more discordant in their weight. © 2014 Wiley Periodicals, Inc.

  16. A comparison of methods of determining the 100 percent survival of preserved red cells

    International Nuclear Information System (INIS)

    Valeri, C.R.; Pivacek, L.E.; Ouellet, R.; Gray, A.

    1984-01-01

    Studies were done to compare three methods to determine the 100 percent survival value from which to estimate the 24-hour posttransfusion survival of preserved red cells. The following methods using small aliquots of 51 Cr-labeled autologous preserved red cells were evaluated: First, the 125 I-albumin method, which is an indirect measurement of the recipient's red cell volume derived from the plasma volume measured using 125 I-labeled albumin and the total body hematocrit. Second, the body surface area method (BSA) in which the recipient's red cell volume is derived from a body surface area nomogram. Third, an extrapolation method, which extrapolates to zero time the radioactivity associated with the red cells in the recipient's circulation from 10 to 20 or 15 to 30 minutes after transfusion. The three methods gave similar results in all studies in which less than 20 percent of the transfused red cells were nonviable (24-hour posttransfusion survival values of between 80-100%), but not when more than 20 percent of the red cells were nonviable. When 21 to 35 percent of the transfused red cells were nonviable (24-hour posttransfusion survivals of 65 to 79%), values with the 125 I-albumin method and the body surface area method were about 5 percent lower (p less than 0.001) than values with the extrapolation method. When greater than 35 percent of the red cells were nonviable (24-hour posttransfusion survival values of less than 65%), values with the 125 I-albumin method and the body surface area method were about 10 percent lower (p less than 0.001) than those obtained by the extrapolation method

  17. Floodplain Mapping Submission for Oregon County, MO

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — The Floodplain Mapping study deliverables depict and quantify the flood risks for Oregon County, MO. The City of Thayer and the Missouri State Emergency Management...

  18. Alternative energy resources for MoDOT

    Science.gov (United States)

    2011-02-01

    This research investigates environmentally friendly alternative energy sources that could be used by MoDOT in various areas, and develops applicable and sustainable strategies to implement those energy sources.

  19. Phase transformations in Mo-doped FINEMETs

    Energy Technology Data Exchange (ETDEWEB)

    Silveyra, Josefina M., E-mail: jsilveyra@fi.uba.a [Lab. de Solidos Amorfos, INTECIN, FIUBA-CONICET, Paseo Colon 850, (C1063ACV) Buenos Aires (Argentina); Illekova, Emilia; Svec, Peter; Janickovic, Dusan [Institute of Physics SAS, Dubravska cesta 9, 845 11 Bratislava (Slovakia); Rosales-Rivera, Andres [Laboratorio de Magnetismo y Materiales Avanzados, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Colombia, Manizales (Colombia); Cremaschi, Victoria J. [Lab. de Solidos Amorfos, INTECIN, FIUBA-CONICET, Paseo Colon 850, (C1063ACV) Buenos Aires (Argentina)

    2010-06-15

    In this paper, the phase transformations occurring during the crystallization process of FINEMETs in which Nb has been gradually replaced by Mo have been studied by a variety of techniques including DSC, DTA, TGA, XRD and TEM. The thermal stability of the alloy was deteriorated as a consequence of Mo's smaller atomic size. The gradual replacement of Nb by Mo reduced the onset temperature of Fe-Si and of the borides. The Curie temperature of the amorphous phase slightly decreased from 594 K for x=0 to 587 K for x=3. The borides compounds Fe{sub 2}B and Fe{sub 23}B{sub 6} as well as the (Nb,Mo){sub 5}Si{sub 3} phase were found to precipitate in the second and third crystallization.

  20. Birth weight in Kohkilooyeh and Boyer Ahmad province, 1999

    Directory of Open Access Journals (Sweden)

    Goshtasbi Nasab A

    2001-10-01

    Full Text Available The newborn's weight at birth is an important measure for newborn's health in all communities. Among developed countries, 70 percent of low birth weight (LBW newborns are preterm. The corresponding figure for undeveloped countries is only 30 percent, there are also evidence of intra-uterine growth retardation among these countries. Among effective factors on LBW, maternal related factors have important role in promotion and improvement of infants and mother's health. This study is a descriptive-analytic one and was conducted cross-sectionally through a questionnair. The study population determined by simple random sampling from newborns under coverage of urban health centers in Kohgiloye and Boyerahmad province. Necessary data collected from existing medical and health records filed in the health centers. Among 285 newborns, 88.4 percent considered with normal weight, 4 percent with IBW and 11.6 percent with more than normal weight. 7.4 percent of cases were immature. 85.3 percent of the mothers in study population were in immune range of age for pregnancy and 7.6 percent of them were illiterate. Except the sex of newborn (P=0.0008 and gestational age at birth (P<0.001 none of the variables demonstrated a significant statistical relation with the birth weight. The results of this study confirm other research's findings and reveal that with improving material factors such as mother's age, employment and literacy, the factors which are effective on birth weight, will be dependent on physiological factors such as sex of newborn and gestational age at birth.

  1. Phase Stability in the Mo-Ti-Zr-C System via Thermodynamic Modeling and Diffusion Multiple Validation

    Science.gov (United States)

    Kar, Sujoy Kumar; Dheeradhada, Voramon S.; Lipkin, Don M.

    2013-08-01

    Alloys in the Mo-rich corner of the Mo-Ti-Zr-C system have found broad applications in non-oxidizing environments requiring structural integrity well beyond 1273 K (1000 °C). Alloys such as TZM (Mo-0.5Ti-0.08Zr-0.03C by weight %) and TZC (Mo-1.2Ti-0.3Zr-0.1C by weight) owe much of their high temperature strength and microstructural stability to MC and M2C carbide phases. In turn, the stability of the respective carbides and the subsequent mechanical behavior of the alloys are strongly dependent on the alloying additions and thermal history. A CALPHAD-based thermodynamic modeling approach is employed to develop a quaternary thermodynamic database for the Mo-Ti-Zr-C system. The thermodynamic database thus developed is validated with diffusion multiple experiments and the validated database is exercised to elucidate the effects of alloying and thermal history on the phase equilibrium in Mo-rich alloys.

  2. PRoMoTo 2013 proceedings

    OpenAIRE

    Bishop, Judith; Tillmann, Nikolai; Puder, Arno; Naik, Vinayak

    2013-01-01

    Programming for Mobile and Touch (PRoMoTo'13) was held at the 2013 ACM SIGPLAN conference on Systems, Programming, Languages and Applications (SPLASH 2013), October 2013 in Indianapolis, USA. Submissions for this event were invited in the general area of mobile and touch-oriented programming languages and programming environments, and teaching of programming for mobile devices. These are proceedings of the PRoMoTo'13.

  3. Similarity in percent body fat between white and Vietnamese women: implication for a universal definition of obesity.

    Science.gov (United States)

    Ho-Pham, Lan T; Lai, Thai Q; Nguyen, Nguyen D; Barrett-Connor, Elizabeth; Nguyen, Tuan V

    2010-06-01

    It has been widely assumed that for a given BMI, Asians have higher percent body fat (PBF) than whites, and that the BMI threshold for defining obesity in Asians should be lower than the threshold for whites. This study sought to test this assumption by comparing the PBF between US white and Vietnamese women. The study was designed as a comparative cross-sectional investigation. In the first study, 210 Vietnamese women ages between 50 and 85 were randomly selected from various districts in Ho Chi Minh City (Vietnam). In the second study, 419 women of the same age range were randomly selected from the Rancho Bernardo Study (San Diego, CA). In both studies, lean mass (LM) and fat mass (FM) were measured by dual-energy X-ray absorptiometry (DXA) (QDR 4500; Hologic). PBF was derived as FM over body weight. Compared with Vietnamese women, white women had much more FM (24.8 +/- 8.1 kg vs. 18.8 +/- 4.9 kg; P or=30, 19% of US white women and 5% of Vietnamese women were classified as obese. Approximately 54% of US white women and 53% of Vietnamese women had their PBF >35% (P = 0.80). Although white women had greater BMI, body weight, and FM than Vietnamese women, their PBF was virtually identical. Further research is required to derive a more appropriate BMI threshold for defining obesity for Asian women.

  4. 99Mo production using MoO3 pellets obtained by mechanical compression and heat treatment

    International Nuclear Information System (INIS)

    Rojas, Jorge; Mendoza, Pablo; Lopez, Alcides

    2014-01-01

    This paper shows the results of the MoO 3 pellets fabrication by mechanical compression and the heat treatment method (MCHT) in order to optimize the production of 99 Mo in the RACSO Nuclear Center. The effects of polyvinyl alcohol (PVA) as binder are assessed by heat treatment of pellets in air atmosphere, evaluating the elimination process with increasing temperature and solubility in 5N NaOH. The results show that the pellets fabrication technique is suitable because fulfills the required technical specifications, allows to irradiate 50 % more of 98 Mo mass and facilitate a safer radiological handling of the irradiated MoO 3 . (authors).

  5. Biodistribution of 99Mo in rats

    International Nuclear Information System (INIS)

    Souza, Raphael Sancho Sisley de; Ribeiro, Bianca da Silva; Dantas, Ana Leticia Almeida; Dantas, Bernardo Maranhao; Bernardo Filho, Mario

    2009-01-01

    The modification of 99 Mo standard metabolism in the presence of MDP would alter the dosimetry of this radionuclide in nuclear medicine patients. Therefore, the objective of this work is to evaluate the influence of MDP in the biodistribution of 99 Mo. Wistar rats were divided in two groups of six animals, being inoculated respectively 99 Molibdate and 99 Mo+MDP via plex ocular. The biodistribution study was carried out after 10 and 120 minutes respectively. The organs were counted with a NaI(Tl) detector. The uptake values did not present significant differences among the groups. An in vitro study through planar chromatography was carried out to determine the affinity between molybdenum and MDP. The results show that 99 Mo has low affinity both to propanone and NaCl-0.9% solution. However, 99 Mo in the presence of MDP presented affinity to NaCl-0.9% solution and low affinity to propanone suggesting that 99 Mo was bound to MDP under the conditions of the experiment. (author)

  6. Microstructural defects modeling in the Al-Mo system

    International Nuclear Information System (INIS)

    Pascuet, Maria I.; Fernandez, Julian R.; Monti, Ana M.

    2006-01-01

    In this work we have utilized computer simulation techniques to study microstructural defects, such as point defects and interfaces, in the Al-Mo alloy. Such alloy is taken as a model to study the Al(fcc)/U-Mo(bcc) interface. The EAM interatomic potential used has been fitted to the formation energy and lattice constant of the AlMo 3 intermetallic. Formation of vacancies for both components Al and Mo and anti-sites, Al Mo and Mo Al , as well as vacancy migration was studied in this structure. We found that the lowest energy defect complex that preserves stoichiometry is the antisite pair Al Mo +Mo Al , in correspondence with other intermetallics of the same structure. Our results also suggest that the structure of the Al(fcc)/Mo(bcc) interface is unstable, while that of the Al(fcc)/Al 5 Mo interface is stable, as observed experimentally. (author) [es

  7. Microstructure and tribological properties of NiMo/Mo2Ni3Si intermetallic 'in-situ' composites

    International Nuclear Information System (INIS)

    Gui Yongliang; Song Chunyan; Yang Li; Qin Xiaoling

    2011-01-01

    Research highlights: → Wear resistant NiMo/Mo 2 Ni 3 Si intermetallic 'in-situ' composites was fabricated successfully with Mo-Ni-Si powder blends as the starting materials. Microstructure of the NiMo/Mo 2 Ni 3 Si composites consists of Mo 2 Ni 3 Si primary dendrites, binary intermetallic phase NiMo and small amount of Ni/NiMo eutectics structure. The NiMo/Mo 2 Ni 3 Si composites exhibited high hardness and outstanding tribological properties under room-temperature dry-sliding wear test conditions which were attributed to the covalent-dominant strong atomic bonds and excellent combination of strength and ductility and toughness. - Abstract: Wear resistant NiMo/Mo 2 Ni 3 Si intermetallic 'in-situ' composites with a microstructure of ternary metal silicide Mo 2 Ni 3 Si primary dendritic, the long strip-like NiMo intermetallic phase, and a small amount of Ni/NiMo eutectics structure were designed and fabricated using molybdenum, nickel and silicon elemental powders. Friction and wear properties of NiMo/Mo 2 Ni 3 Si composites were evaluated under different contact load at room-temperature dry-sliding wear test conditions. Microstructure, worn surface morphologies and subsurface microstructure were characterized by OM, XRD, SEM and EDS. Results indicate that NiMo/Mo 2 Ni 3 Si composites have low fiction coefficient, excellent wear resistance and sluggish wear-load dependence. The dominant wear mechanisms of NiMo/Mo 2 Ni 3 Si composites are soft abrasion and slightly superficial oxidative wear.

  8. Urban percent impervious surface and its relationship with land surface temperature in Yantai City, China

    International Nuclear Information System (INIS)

    Yu, Xinyang; Lu, Changhe

    2014-01-01

    This study investigated percent impervious surface area (PISA) extracted by a four-endmember normalized spectral mixture analysis (NSMA) method and evaluated the reliability of PISA as an indicator of land surface temperature (LST). Landsat Thematic Mapper (TM) and Enhanced Thematic Mapper Plus (ETM+) images for Yantai city, eastern China obtained from USGS were used as the main data source. The results demonstrated that four-endmember NSMA method performed better than the typical three-endmember one, and there was a strong linear relationship between LST and PISA for the two images, which suggest percent impervious surface area provides an alternative parameter for analyzing LST quantitatively in urban areas

  9. Cumulative percent energy deposition of photon beam incident on different targets, simulated by Monte Carlo

    International Nuclear Information System (INIS)

    Kandic, A.; Jevremovic, T.; Boreli, F.

    1989-01-01

    Monte Carlo simulation (without secondary radiation) of the standard photon interactions (Compton scattering, photoelectric absorption and pair protection) for the complex slab's geometry is used in numerical code ACCA. A typical ACCA run will yield: (a) transmission of primary photon radiation differential in energy, (b) the spectrum of energy deposited in the target as a function of position and (c) the cumulative percent energy deposition as a function of position. A cumulative percent energy deposition of photon monoenergetic beam incident on simplest and complexity tissue slab and Fe slab are presented in this paper. (author). 5 refs.; 2 figs

  10. Impact of reduced graphene oxide on MoS{sub 2} grown by sulfurization of sputtered MoO{sub 3} and Mo precursor films

    Energy Technology Data Exchange (ETDEWEB)

    Pacley, Shanee, E-mail: shanee.pacley@us.af.mil; Brausch, Jacob; Beck-Millerton, Emory [U.S. Air Force Research Laboratory (AFRL)/Wright Patterson Air Force Base, Wright Patterson, Ohio 45433-7707 (United States); Hu, Jianjun; Jespersen, Michael [University of Dayton Research Institute, 300 College Park, Dayton, Ohio 45469 (United States); Hilton, Al [Wyle Laboratories, 4200 Colonel Glenn Hwy, Beavercreek, Ohio 45431 (United States); Waite, Adam [University Technology Corporation, 1270 N Fairfield Rd., Beavercreek, Ohio 45432 (United States); Voevodin, Andrey A. [Department of Materials Science and Engineering, University of North Texas, 1155 Union Circle, Denton, Texas 76203 (United States)

    2016-07-15

    Monolayer molybdenum disulfide (MoS{sub 2}), a two dimensional semiconducting dichalcogenide material with a bandgap of 1.8–1.9 eV, has demonstrated promise for future use in field effect transistors and optoelectronics. Various approaches have been used for MoS{sub 2} processing, the most common being chemical vapor deposition. During chemical vapor deposition, precursors such as Mo, MoO{sub 3}, and MoCl{sub 5} have been used to form a vapor reaction with sulfur, resulting in thin films of MoS{sub 2}. Currently, MoO{sub 3} ribbons and powder, and MoCl{sub 5} powder have been used. However, the use of ribbons and powder makes it difficult to grow large area-continuous films. Sputtering of Mo is an approach that has demonstrated continuous MoS{sub 2} film growth. In this paper, the authors compare the structural properties of MoS{sub 2} grown by sulfurization of pulse vapor deposited MoO{sub 3} and Mo precursor films. In addition, they have studied the effects that reduced graphene oxide (rGO) has on MoS{sub 2} structure. Reports show that rGO increases MoS{sub 2} grain growth during powder vaporization. Herein, the authors report a grain size increase for MoS{sub 2} when rGO was used during sulfurization of both sputtered Mo and MoO{sub 3} precursors. In addition, our transmission electron microscopy results show a more uniform and continuous film growth for the MoS{sub 2} films produced from Mo when compared to the films produced from MoO{sub 3}. Atomic force microscopy images further confirm this uniform and continuous film growth when Mo precursor was used. Finally, x-ray photoelectron spectroscopy results show that the MoS{sub 2} films produced using both precursors were stoichiometric and had about 7–8 layers in thickness, and that there was a slight improvement in stoichiometry when rGO was used.

  11. Validity of anthropometric procedures to estimate body density and body fat percent in military men

    Directory of Open Access Journals (Sweden)

    Ciro Romélio Rodriguez-Añez

    1999-12-01

    Full Text Available The objective of this study was to verify the validity of the Katch e McArdle’s equation (1973,which uses the circumferences of the arm, forearm and abdominal to estimate the body density and the procedure of Cohen (1986 which uses the circumferences of the neck and abdominal to estimate the body fat percent (%F in military men. Therefore data from 50 military men, with mean age of 20.26 ± 2.04 years serving in Santa Maria, RS, was collected. The circumferences were measured according with Katch e McArdle (1973 and Cohen (1986 procedures. The body density measured (Dm obtained under water weighting was used as criteria and its mean value was 1.0706 ± 0.0100 g/ml. The residual lung volume was estimated using the Goldman’s e Becklake’s equation (1959. The %F was obtained with the Siri’s equation (1961 and its mean value was 12.70 ± 4.71%. The validation criterion suggested by Lohman (1992 was followed. The analysis of the results indicated that the procedure developed by Cohen (1986 has concurrent validity to estimate %F in military men or in other samples with similar characteristics with standard error of estimate of 3.45%. . RESUMO Através deste estudo objetivou-se verificar a validade: da equação de Katch e McArdle (1973 que envolve os perímetros do braço, antebraço e abdômen, para estimar a densidade corporal; e, o procedimento de Cohen (1986 que envolve os perímetros do pescoço e abdômen, para estimar o % de gordura (%G; para militares. Para tanto, coletou-se os dados de 50 militares masculinos, com idade média de 20,26 ± 2,04 anos, lotados na cidade de Santa Maria, RS. Mensurou-se os perímetros conforme procedimentos de Katch e McArdle (1973 e Cohen (1986. Utilizou-se a densidade corporal mensurada (Dm através da pesagem hidrostática como critério de validação, cujo valor médio foi de 1,0706 ± 0,0100 g/ml. Estimou-se o volume residual pela equação de Goldman e Becklake (1959. O %G derivado da Dm estimou

  12. Spectrophotometric and potentiometric studies of oxidation of Mo(III) by Mo(VI) in phosphoric acid medium

    International Nuclear Information System (INIS)

    Kumar, Arvind; Verma, G.S.P.

    1975-01-01

    Oxidation of Mo(III) (green) by Mo(VI) in an inert atmosphere and in orthophosphoric acid medium at various acid concentrations is reported. Potentiometric and spectrophotometric data suggest that oxidation of Mo(III) proceeds to Mo(V) through a binuclear species Mo(III) Mo(IV) absorbing at 400 nm. The formation of this species is facilitated at high acid concentrations. It is further found that quantitative conversion of Mo(III) into Mo(V) takes place at fairly high acid concentrations. In high phosphoric acid concentrations, solution of Mo(III) has been found to be oxidized to Mo(VI) by air and hence this can be used as a good oxygen absorber. (author)

  13. Spectrophotometric and potentiometric studies of oxidation of Mo(III) by Mo(VI) in phosphoric acid medium

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, A; Verma, G S.P. [Ranchi Coll. (India). Dept. of Chemistry

    1975-12-01

    Oxidation of Mo(III) (green) by Mo(VI) in an inert atmosphere and in orthophosphoric acid medium at various acid concentrations is reported. Potentiometric and spectrophotometric data suggest that oxidation of Mo(III) proceeds to Mo(V) through a binuclear species Mo(III) Mo(IV) absorbing at 400 nm. The formation of this species is facilitated at high acid concentrations. It is further found that quantitative conversion of Mo(III) into Mo(V) takes place at fairly high acid concentrations. In high phosphoric acid concentrations, solution of Mo(III) has been found to be oxidized to Mo(VI) by air and hence this can be used as a good oxygen absorber.

  14. Mindfulness Approaches and Weight Loss, Weight Maintenance, and Weight Regain.

    Science.gov (United States)

    Dunn, Carolyn; Haubenreiser, Megan; Johnson, Madison; Nordby, Kelly; Aggarwal, Surabhi; Myer, Sarah; Thomas, Cathy

    2018-03-01

    There is an urgent need for effective weight management techniques, as more than one third of US adults are overweight or obese. Recommendations for weight loss include a combination of reducing caloric intake, increasing physical activity, and behavior modification. Behavior modification includes mindful eating or eating with awareness. The purpose of this review was to summarize the literature and examine the impact of mindful eating on weight management. The practice of mindful eating has been applied to the reduction of food cravings, portion control, body mass index, and body weight. Past reviews evaluating the relationship between mindfulness and weight management did not focus on change in mindful eating as the primary outcome or mindful eating as a measured variable. This review demonstrates strong support for inclusion of mindful eating as a component of weight management programs and may provide substantial benefit to the treatment of overweight and obesity.

  15. Measurement of Mo-99 column activity in the evaluation of Mo-99/Tc-99m generator

    International Nuclear Information System (INIS)

    Kuster, Z.

    1994-01-01

    In order to calculate the real elution efficiency of Mo-99/Tc-99m generator the Mo-99 content on the column has to be previously determined. As found in this work, the external measurement of Mo-99-column activity by means of Geiger-Mueller counter is a simple, fast and reliable method. Generally, Mo-99-column is placed slightly out of the center of the generator; therefore the externally measured flux of photons (φ) is an angular-dependent function. If the thickness of the lead container is radially uniform, the flux measured at some distance from the generator (which is rotated in 2π/3 steps) is given by the equation φ = A (1 + Bcos (α-2π(i - 2)/3)) -1 , i=1,2 or 3 (Eq.1) where A is a numerical constant depending on the Mo-99-column activity, B is a numerical constant depending on the Mo-99- column position within the lead container, the angle α depends on the initial orientation of the generator. A total of 20 generator were studied. The measured Mo-99-column activities (Capintec dose calibrator) were in the range 13.1- 35.11 GBq. Contrary to the findings of Vinberg and Kristensen (Eur J Nucl Med 1/1976(219), values of A (Eq. 1) are in good correlation (r 2 =0.9794) with the measured Mo-99-column activities. (author)

  16. EXAFS study of Mo2N and Mo nitrides supported on zeolites

    International Nuclear Information System (INIS)

    Liu Zhenlin; Meng Ming; Fu Yilu; Jiang Ming; Hu Tiandou; Xie Yaning; Liu Tao

    2002-01-01

    In the present study, the reaction is applied to prepare molybdenum nitrides with high surface area, and zeolites are used as supports. The EXAFS of the Mo K-absorption edge is measured and the change of coordination environment of Mo atoms before and after the nitridation is revealed

  17. DFT study of the reactions of Mo and Mo with CO2 in gas phase

    Indian Academy of Sciences (India)

    understanding the mechanism of second-row metal reacting with CO2. The minimum energy ... et al.18 performed an IR study on the reaction of laser- ablated Mo atom .... indicate that the weak electrostatic interaction between. Mo. + and CO2 ...

  18. Study on soft magnetic properties of Finemet-type nanocrystalline alloys with Mo substituting for Nb

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Dehui; Zhou, Bingwen; Jiang, Boyu; Ya, Bin; Zhang, Xingguo [School of Materials Science and Engineering, Dalian University of Technology, Dalian (China)

    2017-10-15

    The thermal stability, microstructure, and soft magnetic properties as a function of annealing time were studied for Fe{sub 73.5}Si{sub 13.5}B{sub 9}Cu{sub 1}Nb{sub 3-x}Mo{sub x} (x = 0, 1, 2, 3) (atom percent, at.%,) ribbons. It was found that substituting Nb by Mo reduced the thermal stability. After 15 min short time vacuum annealing, Fe{sub 73.5}Si{sub 13.5}B{sub 9}Cu{sub 1}Nb{sub 2}Mo{sub 1} and Fe{sub 73.5}Si{sub 13.5}B{sub 9}Cu{sub 1}Nb{sub 1}Mo{sub 2} samples obtained higher permeability and similar coercivity compared to the original Finemet alloy (Fe{sub 73.5}Si{sub 13.5}B{sub 9}Cu{sub 1}Nb{sub 3}), Mo substituting Nb reduced the optimum annealing time in Finemet-type alloys, and meanwhile marginally increased the saturation magnetization. Substituting all Nb by Mo led to the earlier formation of non-soft magnetic phase, thus deteriorated the soft magnetic properties. XRD and TEM structural analysis showed that in Fe{sub 73.5}Si{sub 13.5}B{sub 9}Cu{sub 1}Nb{sub 2}Mo{sub 1} and Fe{sub 73.5}Si{sub 13.5}B{sub 9}Cu{sub 1}Nb{sub 1}Mo{sub 2} samples (annealed for 15 min), nanocrystals ∝10 nm in size were obtained, and the good soft magnetic properties of these alloys could be attributed to the small grain size. The relationship between annealing time, soft magnetic properties, and microstructure was established. Reducing annealing time and temperature to obtain best soft magnetic properties could cut down the production costs of Finemet-type alloys. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. Cu4Pr6(MoO4)11-Pr2(MoO4)3 system

    International Nuclear Information System (INIS)

    Arzumanyan, G.A.

    1982-01-01

    Existence boundaries and Dalton compositions (CuPr(MoO 4 ) 2 , CuPr 3 (MoO 4 ) 5 ) of solid solutions that in the mojority are of shcheelite dsitored structure have been determined in the Cu 4 Pr 6 (MoO 4 ) 11 -Pr 2 (MoO 4 ) 3 system. It has been revealed that regions of homogeneity near the CuPr(MoO 4 ) 2 composition have a horseshoeshaped profile

  20. The Determination of the Percent of Oxygen in Air Using a Gas Pressure Sensor

    Science.gov (United States)

    Gordon, James; Chancey, Katherine

    2005-01-01

    The experiment of determination of the percent of oxygen in air is performed in a general chemistry laboratory in which students compare the results calculated from the pressure measurements obtained with the calculator-based systems to those obtained in a water-measurement method. This experiment allows students to explore a fundamental reaction…

  1. Field method to measure changes in percent body fat of young women: The TIGER Study

    Science.gov (United States)

    Body mass index (BMI), waist (W) and hip (H) circumference (C) are commonly used to assess changes in body composition for field research. We developed a model to estimate changes in dual energy X-ray absorption (DXA) percent fat (% fat) from these variables with a diverse sample of young women fro...

  2. Generalized equations for estimating DXA percent fat of diverse young women and men: The Tiger Study

    Science.gov (United States)

    Popular generalized equations for estimating percent body fat (BF%) developed with cross-sectional data are biased when applied to racially/ethnically diverse populations. We developed accurate anthropometric models to estimate dual-energy x-ray absorptiometry BF% (DXA-BF%) that can be generalized t...

  3. European Community Can Reduce CO2 Emissions by Sixty Percent : A Feasibility Study

    NARCIS (Netherlands)

    Mot, E.; Bartelds, H.; Esser, P.M.; Huurdeman, A.J.M.; Laak, P.J.A. van de; Michon, S.G.L.; Nielen, R.J.; Baar, H.J.W. de

    1993-01-01

    Carbon dioxide (CO2) emissions in the European Community (EC) can be reduced by roughly 60 percent. A great many measures need to be taken to reach this reduction, with a total annual cost of ECU 55 milliard. Fossil fuel use is the main cause of CO2 emissions into the atmosphere; CO2 emissions are

  4. 48 CFR 836.606-73 - Application of 6 percent architect-engineer fee limitation.

    Science.gov (United States)

    2010-10-01

    ... architect-engineer fee limitation. 836.606-73 Section 836.606-73 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS SPECIAL CATEGORIES OF CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Architect-Engineer Services 836.606-73 Application of 6 percent architect-engineer fee limitation...

  5. 46 CFR 42.20-8 - Flooding standard: Type “B” vessel, 100 percent reduction.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Flooding standard: Type âBâ vessel, 100 percent... LINES DOMESTIC AND FOREIGN VOYAGES BY SEA Freeboards § 42.20-8 Flooding standard: Type “B” vessel, 100...-11 as applied to the following flooding standards: (1) If the vessel is 225 meters (738 feet) or less...

  6. Identification of a novel percent mammographic density locus at 12q24.

    Science.gov (United States)

    Stevens, Kristen N; Lindstrom, Sara; Scott, Christopher G; Thompson, Deborah; Sellers, Thomas A; Wang, Xianshu; Wang, Alice; Atkinson, Elizabeth; Rider, David N; Eckel-Passow, Jeanette E; Varghese, Jajini S; Audley, Tina; Brown, Judith; Leyland, Jean; Luben, Robert N; Warren, Ruth M L; Loos, Ruth J F; Wareham, Nicholas J; Li, Jingmei; Hall, Per; Liu, Jianjun; Eriksson, Louise; Czene, Kamila; Olson, Janet E; Pankratz, V Shane; Fredericksen, Zachary; Diasio, Robert B; Lee, Adam M; Heit, John A; DeAndrade, Mariza; Goode, Ellen L; Vierkant, Robert A; Cunningham, Julie M; Armasu, Sebastian M; Weinshilboum, Richard; Fridley, Brooke L; Batzler, Anthony; Ingle, James N; Boyd, Norman F; Paterson, Andrew D; Rommens, Johanna; Martin, Lisa J; Hopper, John L; Southey, Melissa C; Stone, Jennifer; Apicella, Carmel; Kraft, Peter; Hankinson, Susan E; Hazra, Aditi; Hunter, David J; Easton, Douglas F; Couch, Fergus J; Tamimi, Rulla M; Vachon, Celine M

    2012-07-15

    Percent mammographic density adjusted for age and body mass index (BMI) is one of the strongest risk factors for breast cancer and has a heritable component that remains largely unidentified. We performed a three-stage genome-wide association study (GWAS) of percent mammographic density to identify novel genetic loci associated with this trait. In stage 1, we combined three GWASs of percent density comprised of 1241 women from studies at the Mayo Clinic and identified the top 48 loci (99 single nucleotide polymorphisms). We attempted replication of these loci in 7018 women from seven additional studies (stage 2). The meta-analysis of stage 1 and 2 data identified a novel locus, rs1265507 on 12q24, associated with percent density, adjusting for age and BMI (P = 4.43 × 10(-8)). We refined the 12q24 locus with 459 additional variants (stage 3) in a combined analysis of all three stages (n = 10 377) and confirmed that rs1265507 has the strongest association in the 12q24 region (P = 1.03 × 10(-8)). Rs1265507 is located between the genes TBX5 and TBX3, which are members of the phylogenetically conserved T-box gene family and encode transcription factors involved in developmental regulation. Understanding the mechanism underlying this association will provide insight into the genetics of breast tissue composition.

  7. Radial growth and percent of latewood in Scots pine provenance trials in Western and Central Siberia

    Directory of Open Access Journals (Sweden)

    S. R. Kuzmin

    2016-12-01

    Full Text Available Percent of latewood of Boguchany and Suzun Scots pine climatypes has been studied in two provenance trials (place of origin and trial place. For Boguchany climatype the place of origin is south taiga of Central Siberia (Krasnoyarsk Krai, the place of trial is forest-steppe zone of Western Siberia (Novosibirsk Oblast and vice versa for Suzun climatype – forest-steppe zone of Western Siberia is the place of origin, south taiga is the place of trial. Comparison of annual average values of latewood percent of Boguchany climatype in south taiga and forest-steppe revealed the same numbers – 19 %. Annual variability of this trait in south taiga is distinctly lower and equal to 17 %, in forest-steppe – 35 %. Average annual values of latewood percent of Suzun climatype in the place of origin and trial place are close (20 and 21 %. Variability of this trait for Suzun climatype is higher than for Boguchany and equal to 23 % in south taiga and 42 % in forest-steppe. Climatic conditions in southern taiga in Central Siberia in comparison with forest-steppe in Western Siberia make differences between climatypes stronger. Differences between climatypes are expressed in different age of maximal increments of diameter, different tree ring width and latewood percent values and in different latewood reaction to weather conditions.

  8. Temporal divergence of percent body fat and body mass index in pre-teenage children: the LOOK longitudinal study.

    Science.gov (United States)

    Telford, R D; Cunningham, R B; Abhayaratna, W P

    2014-12-01

    The index of body mass related to stature, (body mass index, BMI, kgm(-2) ), is widely used as a proxy for percent body fat (%BF) in cross-sectional and longitudinal investigations. BMI does not distinguish between lean and fat mass and in children, the cross-sectional relationship between %BF and BMI changes with age and sex. While BMI increases linearly with age from age 8 to 12 years in both boys and girls, %BF plateaus off between 10 and 12 years. Repeated measures in children show a systematic decrease in %BF for any given BMI from age 8 to 10 to 12 years. Because changes in BMI misrepresent changes in %BF, its use as a proxy of %BF should be avoided in longitudinal studies in this age group. Body mass index (BMI, kgm(-2) ) is commonly used as an indicator of pediatric adiposity, but with its inability to distinguish changes in lean and fat mass, its use in longitudinal studies of children requires careful consideration. To investigate the suitability of BMI as a surrogate of percent body fat (%BF) in pediatric longitudinal investigations. In this longitudinal study, healthy Australian children (256 girls and 278 boys) were measured at ages 8.0 (standard deviation 0.3), 10.0 and 12.0 years for height, weight and percent body fat (%BF) by dual-energy X-ray absorptiometry. The patterns of change in the means of %BF and BMI were different (P < 0.001). While mean BMI increased linearly from 8 to 12 years of age, %BF did not change between 10 and 12 years. Relationships between %BF and BMI in boys and girls were curvilinear and varied with age (P < 0.001) and gender (P < 0.001); any given BMI corresponding with a lower %BF as a child became older. Considering the divergence of temporal patterns of %BF and BMI between 10 and 12 years of age, employment of BMI as a proxy for %BF in absolute or age and sex standardized forms in pediatric longitudinal investigations is problematical. © 2013 The Authors. Pediatric Obesity © 2013 International Association

  9. ITO-free flexible organic photovoltaics with multilayer MoO3/LiF/MoO3/Ag/MoO3 as the transparent electrode

    International Nuclear Information System (INIS)

    Chen, Shilin; Dai, Yunjie; Zhang, Hongmei; Zhao, Dewei

    2016-01-01

    We present efficient flexible organic photovoltaics (OPVs) with multiple layers of molybdenum oxide (MoO 3 )/LiF/MoO 3 /Ag/MoO 3 as the transparent electrode, where the thin Ag layer yields high conductivity and the dielectric layer MoO 3 /LiF/MoO 3 has high transparency due to optical interference, leading to improved power conversion efficiency compared with indium tin oxide (ITO) based devices. The MoO 3 contacting organic active layer is used as a buffer layer for good hole extraction. Thus, the multilayer MoO 3 /LiF/MoO 3 /Ag/MoO 3 can improve light transmittance and also facilitate charge carrier extraction. Such an electrode shows excellent mechanical bendability with a 9% reduction of efficiency after 1000 cycles of bending due to the ductile nature of the thin metal layer and dielectric layer used. Our results suggest that the MoO 3 /LiF/MoO 3 /Ag/MoO 3 multilayer electrode is a promising alternative to ITO as an electrode in OPVs. (paper)

  10. Weight Gain during Pregnancy

    Science.gov (United States)

    ... Global Map Premature Birth Report Cards Careers Archives Pregnancy Before or between pregnancies Nutrition, weight & fitness Prenatal ... fitness > Weight gain during pregnancy Weight gain during pregnancy E-mail to a friend Please fill in ...

  11. Should I Gain Weight?

    Science.gov (United States)

    ... Videos for Educators Search English Español Should I Gain Weight? KidsHealth / For Teens / Should I Gain Weight? ... something about it. Why Do People Want to Gain Weight? Some of the reasons people give for ...

  12. A new approach to quantification of DTPA incorporation into monoclonal antibodies (MoAbs) labeled by the cyclic anhydride DTPA method

    International Nuclear Information System (INIS)

    Wang, T.S.T.; Ng, A.K.; Fawwaz, R.A.; Alsedairy, S.; Alderson, P.O.

    1985-01-01

    A method for determining the ratio of DTPA molecules attached per molecule of Ab was developed and used to examine the immunoreactivity of different Abs as a function of the amount of incorporated DTPA. The bicyclic anhydride of DTPA[2-C-14]acetic acid (BADTPA-C-14) was synthesized by reacting DTPA[2-C-14]acetic acid (1mCi/mmo1) and acetic anhydride. BADTPA-C-14 then was reacted with a MoAb to a melanoma associated antigen (MA) and to a MoAb to human HLA class II antigen (HLA) at 2mg/m1 of MoAb concentration, at MoAb to BADTPA-C-14 ratios (mmo1/mmo1) of l:1, 1:10, 1:00, l:200. The conjugate was dialyzed exhaustively against HEPES at pH 7.0. The MoAb concentration was measured at 280mm of uv; the DTPA/MoAb ratio was calculated based on the specific activity of BADTPA-C-14, and the immunoreactivity was assessed by direct cell-binding to melanoma, the HLA antigen and control (lymphoma) cells. Percent binding to the lymphoid cell line was less than 3%. The authors' results demonstrated a method for directly determining the number of DTPA molecules attached to a MOAb, and demonstrated variations in immunoreactivity as the number of DTPA groups per MoAb is altered

  13. Room temperature isotherms for Mo and Ni

    International Nuclear Information System (INIS)

    Masse, J.L.

    1986-11-01

    Isotherms at room temperature for Mo and Ni are proposed. They are of three types: BIRCH, KEANE and BORN-MIE. The adjustable constants appearing in these isotherms have been determined from experimental quantities at zero pressure. An evaluation of the limit of (δB T /δP) T as P #-> # ∞, where B T is the isothermal bulk modulus, has been also used. These three isotherms obtained for Mo and Ni are compared with isotherms derived from shock-wave data according to the PRIETO's model. There is a good agreement between these and these derived from shock-wave data. The three isotherms proposed for Mo and Ni can be considered as valid until pressures of several B To , where B To is the bulk modulus B T at P = o [fr

  14. Wetting of metals and glasses on Mo

    Energy Technology Data Exchange (ETDEWEB)

    Saiz, Eduardo; Tomsia, Antoni P.; Saiz, Eduardo; Lopez-Esteban, Sonia; Benhassine, Mehdi; de Coninck, Joel; Rauch, Nicole; Ruehle, Manfred

    2008-01-08

    The wetting of low melting point metals and Si-Ca-Al-Ti-O glasses on molybdenum has been investigated. The selected metals (Au, Cu, Ag) form a simple eutectic with Mo. Metal spreading occurs under nonreactive conditions without interdiffusion or ridge formation. The metals exhibit low (non-zero) contact angles on Mo but this requires temperatures higher than 1100 C in reducing atmospheres in order to eliminate a layer of adsorbed impurities on the molybdenum surface. By controlling the oxygen activity in the furnace, glass spreading can take place under reactive or nonreactive conditions. We have found that in the glass/Mo system the contact angle does not decrease under reactive conditions. In all cases, adsorption from the liquid seems to accelerate the diffusivity on the free molybdenum surface.

  15. Vedinių su priesaga *-mo- raida

    Directory of Open Access Journals (Sweden)

    Saulius Ambrazas

    2011-12-01

    Full Text Available DEVELOPMENT OF DERIVATIVES WITH THE SUFFIX *-mo-SummaryAdjectives with the suffix *-mo- have been formed from substantives (cf. Lith. tólimas / tólymas and Latv. dial. tuôl’eims ‘distant’; Pruss. *auktimas ‘high’; Skr. agrimá- ‘the first, who is at the head’ and verbs (cf. Lith. dial. ãpsukmas ‘sewn round’, pliùkšmas ‘deflated, limp’; OLith. laimas ‘happy’ and Pruss. etnīstislaims (gnadenreich III 631; Lith. liñksmas and Latv. lìksms ‘merry, gay, joyfull’, Gmc. *werma- ‘warm’, Skr. bhīmá- ‘terrible, frightfull’, Toch. A, B cämpamo- ‘well-to-do, rich’, Hitt. kišamma- ‘combed’ from the Late Proto-Indo-European. The gratest part of them became participles in the Baltic, Slavic and Albanian languages.On the other hand, the use of derivatives with the suffix *-mo- in the position of abstract nouns is also very old, cf. semanticaly concretized and derivationaly indissoluble abstract noun, in herited from Proto-Indo-European, Lith. dmas (dmai, Latv. dũmi, Pruss. dumis (rauch E 39, Slav. *dymъ, Latv. fūmus, Skr. dhūmó- ‘smoke’ and Gk. θῡ‑μός with abstract meaning ‘soal, vitality, passion,    need’ : dhe-/dh-/dhū- ‘blow; breathe; choke; smoke; rush; disperse; whirl, move, stir’.In the East Baltic languages abstract nouns with the derived suffixes, based on *-mo-, became productive, cf. nomina actionis with *-i-mo- in Lithuanian (cf. gyvẽnimas ‘life’ and corresponding derivatives with *-u-mo- in Latvian (cf. ìeradums ‘custom, habit’.

  16. 40 CFR 60.1450 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn 100 percent yard waste? 60.1450 Section 60.1450 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1450 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use EPA Reference Method 9 in appendix A of...

  17. 40 CFR 60.1925 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn 100 percent yard waste? 60.1925 Section 60.1925 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1925 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use...

  18. 40 CFR 62.15375 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn 100 percent yard waste? 62.15375 Section 62.15375 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15375 What are the emission limits for air curtain incinerators that burn 100 percent yard...

  19. 40 CFR 60.1445 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn 100 percent yard waste? 60.1445 Section 60.1445 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1445 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If your air curtain incinerator combusts...

  20. 40 CFR 62.15380 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn 100 percent yard waste? 62.15380 Section 62.15380 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15380 How must I monitor opacity for air curtain incinerators that burn 100 percent yard...

  1. 40 CFR 60.1920 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn 100 percent yard waste? 60.1920 Section 60.1920 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1920 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If...

  2. Elevated Temperature Tensile Tests on DU–10Mo Rolled Foils

    Energy Technology Data Exchange (ETDEWEB)

    Schulthess, Jason [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    Tensile mechanical properties for uranium-10 wt.% molybdenum (U–10Mo) foils are required to support modeling and qualification of new monolithic fuel plate designs. It is expected that depleted uranium-10 wt% Mo (DU–10Mo) mechanical behavior is representative of the low enriched U–10Mo to be used in the actual fuel plates, therefore DU-10Mo was studied to simplify material processing, handling, and testing requirements. In this report, tensile testing of DU-10Mo fuel foils prepared using four different thermomechanical processing treatments were conducted to assess the impact of foil fabrication history on resultant tensile properties.

  3. The modulation of Schottky barriers of metal-MoS2 contacts via BN-MoS2 heterostructures.

    Science.gov (United States)

    Su, Jie; Feng, Liping; Zhang, Yan; Liu, Zhengtang

    2016-06-22

    Using first-principles calculations within density functional theory, we systematically studied the effect of BN-MoS2 heterostructure on the Schottky barriers of metal-MoS2 contacts. Two types of FETs are designed according to the area of the BN-MoS2 heterostructure. Results show that the vertical and lateral Schottky barriers in all the studied contacts, irrespective of the work function of the metal, are significantly reduced or even vanish when the BN-MoS2 heterostructure substitutes the monolayer MoS2. Only the n-type lateral Schottky barrier of Au/BN-MoS2 contact relates to the area of the BN-MoS2 heterostructure. Notably, the Pt-MoS2 contact with n-type character is transformed into a p-type contact upon substituting the monolayer MoS2 by a BN-MoS2 heterostructure. These changes of the contact natures are ascribed to the variation of Fermi level pinning, work function and charge distribution. Analysis demonstrates that the Fermi level pinning effects are significantly weakened for metal/BN-MoS2 contacts because no gap states dominated by MoS2 are formed, in contrast to those of metal-MoS2 contacts. Although additional BN layers reduce the interlayer interaction and the work function of the metal, the Schottky barriers of metal/BN-MoS2 contacts still do not obey the Schottky-Mott rule. Moreover, different from metal-MoS2 contacts, the charges transfer from electrodes to the monolayer MoS2, resulting in an increment of the work function of these metals in metal/BN-MoS2 contacts. These findings may prove to be instrumental in the future design of new MoS2-based FETs with ohmic contact or p-type character.

  4. Austrian Business Cycle Theory: Are 100 Percent Reserves Sufficient to Prevent a Business Cycle?

    Directory of Open Access Journals (Sweden)

    Philipp Bagus

    2010-02-01

    Full Text Available Authors in the Austrian tradition have made the credit expansion of a fractional reserve banking system as the prime cause of business cycles. Authors such as Selgin (1988 and White (1999 have argued that a solution to this problem would be a free banking system. They maintain that the competition between banks would limit the credit expansion effectively. Other authors such as Rothbard (1991 and Huerta de Soto (2006 have gone further and advocated a 100 percent reserve banking system ruling out credit expansion altogether. In this article it is argued that a 100 percent reserve system can still bring about business cycles through excessive maturity mismatching between deposits and loans.

  5. Amazing 7-day, super-simple, scripted guide to teaching or learning percents

    CERN Document Server

    Hernandez, Lisa

    2014-01-01

    Welcome to The Amazing 7-Day, Super-Simple, Scripted Guide to Teaching or Learning Percents. I have attempted to do just what the title says: make learning percents super simple. I have also attempted to make it fun and even ear-catching. The reason for this is not that I am a frustrated stand-up comic, but because in my fourteen years of teaching the subject, I have come to realize that my jokes, even the bad ones, have a crazy way of sticking in my students' heads. And should I use a joke (even a bad one) repetitively, the associations become embedded in their brains, many times to their cha

  6. Mechanisms of Weight Regain following Weight Loss.

    Science.gov (United States)

    Blomain, Erik Scott; Dirhan, Dara Anne; Valentino, Michael Anthony; Kim, Gilbert Won; Waldman, Scott Arthur

    2013-01-01

    Obesity is a world-wide pandemic and its incidence is on the rise along with associated comorbidities. Currently, there are few effective therapies to combat obesity. The use of lifestyle modification therapy, namely, improvements in diet and exercise, is preferable over bariatric surgery or pharmacotherapy due to surgical risks and issues with drug efficacy and safety. Although they are initially successful in producing weight loss, such lifestyle intervention strategies are generally unsuccessful in achieving long-term weight maintenance, with the vast majority of obese patients regaining their lost weight during followup. Recently, various compensatory mechanisms have been elucidated by which the body may oppose new weight loss, and this compensation may result in weight regain back to the obese baseline. The present review summarizes the available evidence on these compensatory mechanisms, with a focus on weight loss-induced changes in energy expenditure, neuroendocrine pathways, nutrient metabolism, and gut physiology. These findings have added a major focus to the field of antiobesity research. In addition to investigating pathways that induce weight loss, the present work also focuses on pathways that may instead prevent weight regain. Such strategies will be necessary for improving long-term weight loss maintenance and outcomes for patients who struggle with obesity.

  7. Tranexamic Acid Reduced the Percent of Total Blood Volume Lost During Adolescent Idiopathic Scoliosis Surgery.

    Science.gov (United States)

    Jones, Kristen E; Butler, Elissa K; Barrack, Tara; Ledonio, Charles T; Forte, Mary L; Cohn, Claudia S; Polly, David W

    2017-01-01

    Multilevel posterior spine fusion is associated with significant intraoperative blood loss. Tranexamic acid is an antifibrinolytic agent that reduces intraoperative blood loss. The goal of this study was to compare the percent of total blood volume lost during posterior spinal fusion (PSF) with or without tranexamic acid in patients with adolescent idiopathic scoliosis (AIS). Thirty-six AIS patients underwent PSF in 2011-2014; the last half (n=18) received intraoperative tranexamic acid. We retrieved relevant demographic, hematologic, intraoperative and outcomes information from medical records. The primary outcome was the percent of total blood volume lost, calculated from estimates of intraoperative blood loss (numerator) and estimated total blood volume per patient (denominator, via Nadler's equations). Unadjusted outcomes were compared using standard statistical tests. Tranexamic acid and no-tranexamic acid groups were similar (all p>0.05) in mean age (16.1 vs. 15.2 years), sex (89% vs. 83% female), body mass index (22.2 vs. 20.2 kg/m2), preoperative hemoglobin (13.9 vs. 13.9 g/dl), mean spinal levels fused (10.5 vs. 9.6), osteotomies (1.6 vs. 0.9) and operative duration (6.1 hours, both). The percent of total blood volume lost (TBVL) was significantly lower in the tranexamic acid-treated vs. no-tranexamic acid group (median 8.23% vs. 14.30%, p = 0.032); percent TBVL per level fused was significantly lower with tranexamic acid than without it (1.1% vs. 1.8%, p=0.048). Estimated blood loss (milliliters) was similar across groups. Tranexamic acid significantly reduced the percentage of total blood volume lost versus no tranexamic acid in AIS patients who underwent PSF using a standardized blood loss measure.Level of Evidence: 3. Institutional Review Board status: This medical record chart review (minimal risk) study was approved by the University of Minnesota Institutional Review Board.

  8. Phase relations in the M2MoO4 - Ag2MoO4 - Hf(MoO4)2 (M=Li, Na) systems

    International Nuclear Information System (INIS)

    Bazarova, Zh.G.; Bazarov, B.G.; Balsanova, L.V.

    2002-01-01

    The M 2 MoO 4 - Ag 2 MoO 4 - Hf(MoO 4 ) 2 (M=Li, Na) systems were studied by X-ray diffraction and differential thermal analyses in the subsolidus area (450 - 500 Deg C) for the first time. The formation of the binary compound with the variable composition Li 4-x Hf 1+0.2x (MoO 4 ) 4 (0 ≤ x ≤ 0.6) in the Li 2 MoO 4 - Hf(MoO 4 ) 2 system and the ternary molybdates Li 4 Ag 2 Hf(MoO 4 ) 5 (S 1 ) and Na 2 Ag 2 Hf(MoO 4 ) 4 (S 2 ) was established and the thermal characteristics of the prepared compounds were examined. The new binary molybdate Ag 2 Hf(MoO 4 ) 3 was prepared by the reaction between Ag 2 MoO 4 and Hf(MoO 4 ) 2 [ru

  9. Effect of LaB6 on the thermal shock property of MoSi2-SiC coating for carbon/carbon composites

    International Nuclear Information System (INIS)

    Li Ting; Li Hejun; Shi Xiaohong

    2013-01-01

    Highlights: ► LaB 6 -MoSi 2 -SiC and MoSi 2 -SiC multi-composition coatings were coated on C/C composites by pack cementation. ► The microstructure and thermal shock resistance of both coatings were investigated. ► The addition of LaB 6 can increase the compactness, flexural strength and fracture toughness of the MoSi 2 -SiC coating simultaneously. ► Both coatings bond well with the substrates before and after thermal cycling oxidation between 1773 K and room temperature. ► The LaB 6 -MoSi 2 -SiC coated C/C shows better thermal shock resistance than the MoSi 2 -SiC coated C/C. - Abstract: LaB 6 -MoSi 2 -SiC and MoSi 2 -SiC coatings were prepared on the surface of carbon/carbon composites by pack cementation method. The crystal structures of the coatings were measured by X-ray diffraction. The morphologies and element distributions were also analyzed by scanning electron microscopy and energy dispersive spectroscopy, respectively. The effect of LaB 6 on the microstructure and thermal shock resistance of MoSi 2 -SiC coating was investigated. The results indicated that the LaB 6 -MoSi 2 -SiC coating possessed a denser structure and superior thermal shock resistance. After 25 times of thermal cycling oxidation between 1773 K and room temperature, the weight losses of the LaB 6 -MoSi 2 -SiC and MoSi 2 -SiC coated samples were 0.627% and 2.019%, respectively.

  10. Synthesis of rambutan-like MoS2/mesoporous carbon spheres nanocomposites with excellent performance for supercapacitors

    Science.gov (United States)

    Zhang, Shouchuan; Hu, Ruirui; Dai, Peng; Yu, Xinxin; Ding, Zongling; Wu, Mingzai; Li, Guang; Ma, Yongqing; Tu, Chuanjun

    2017-02-01

    A novel rambutan-like composite of MoS2/mesoporous carbon spheres were synthesized by a simple two-step hydrothermal and post-annealing approach via using glucose as C source and Na2MoO4·2H2O and thiourea as Mo and S sources. It is found that the morphology and electrochemical properties can be effectively controlled by the change of the weight ratio of coated MoS2 sheets to carbon spheres. When used as electrode material for supercapacitor, the hybrid MoS2/carbon spheres show a high specific capacity of 411 F/g at a current density of 1 A/g and 272 F/g at a high discharge current density of 10 A/g. The annealing treatment at 700 °C transformed the core carbon spheres into mesoporous ones, which served as the conduction network and favor the enhancement of the specific capacitance. In addition, the strain released during the charge/discharge process can be accommodated and the structural integrity can be kept, improving the cycling life. After 1000 cycles, the capacitance retention of the hybrid MoS2/carbon spheres is 93.2%.

  11. Longitudinal drop-out and weighting against its bias

    Directory of Open Access Journals (Sweden)

    Steffen C. E. Schmidt

    2017-12-01

    Full Text Available Abstract Background The bias caused by drop-out is an important factor in large population-based epidemiological studies. Many studies account for it by weighting their longitudinal data, but to date there is no detailed final approach for how to conduct these weights. Methods In this study we describe the observed longitudinal bias and a three-step longitudinal weighting approach used for the longitudinal data in the MoMo baseline (N = 4528, 4–17 years and wave 1 study with 2807 (62% participants between 2003 and 2012. Results The most meaningful drop-out predictors were socioeconomic status of the household, socioeconomic characteristics of the mother and daily TV usage. Weighting reduced the bias between the longitudinal participants and the baseline sample, and also increased variance by 5% to 35% with a final weighting efficiency of 41.67%. Conclusions We conclude that a weighting procedure is important to reduce longitudinal bias in health-oriented epidemiological studies and suggest identifying the most influencing variables in the first step, then use logistic regression modeling to calculate the inverse of the probability of participation in the second step, and finally trim and standardize the weights in the third step.

  12. Effect of 67Cu and 99Mo labeled tetrathiomolybdate on the distribution of 67Cu, Cu, and 99Mo in bile fractions in sheep

    International Nuclear Information System (INIS)

    Gooneratne, R.; Laarveld, B.; Christensen, D.

    1989-01-01

    The effect of intravenous administration of 67 Cu and 99 Mo labeled tetrathiomolybdate (TTM) on the appearance of 67 Cu, stable Cu, and 99 Mo in gel chromatographic fractions of bile was examined in sheep fed either 5 or 35 mg Cu kg-1 DM. Peak excretory periods of biliary 67 Cu, stable Cu, and 99 Mo were observed at 30 min-1.25 hr, 2-3 hr, and 11-13 hr after 67 Cu and after 99 Mo labeled TTM. Sephadex G-75 gel filtration of bile samples collected at 1, 3, and 12 hr after 67 Cu administration revealed two major protein peaks of molecular weights of greater than 80,000 (peak I) and 7,000 (peak II) containing both 67 Cu and Cu. But the ratio of 67 Cu in the two peaks varied with time of bile collection. The ratio of areas of peak I:II 1 hr after 67 Cu administration was approximately 0.48; at 3 hr, 0.62, and at 12 hr 1.35. Tetrathiomolybdate administration increased both 67 Cu and stable Cu in bile by severalfold and induced a major shift of Cu into the higher molecular weight protein fraction. The experiments confirm the effectiveness of TTM as a ''decoppering'' agent. Furthermore, TTM not only promoted bile Cu excretion, but it also increased the incorporation of Cu into the macromolecular fraction. This may limit enterohepatic circulation of biliary Cu and thereby cause an overall Cu depletion and a negative Cu balance

  13. Investigation of BaMoO4-Ln2(MoO4)3 systems (Ln = Nd, Sm, Yb)

    International Nuclear Information System (INIS)

    Vakulyuk, V.V.; Evdokimov, A.A.; Khomchenko, G.P.

    1982-01-01

    Using the methods of X-ray phase and differential-thermal analyses phase ratios in the systems BaMoO 4 -Ln 2 (MoO 4 ) 3 (Ln=Nd, Sm, Yb); BaNd 2 (MoO 4 ) 4 -MaGd 2 (MoO 4 ) are studied. Unit cell parameters and the character of melting of the compounds BaLn 2 (MoO 4 ) 4 are specified. Effect of growth conditions on laminated nature of BaGd 2 (MoO 4 ) 4 monocrystals is studied

  14. Proven Weight Loss Methods

    Science.gov (United States)

    Fact Sheet Proven Weight Loss Methods What can weight loss do for you? Losing weight can improve your health in a number of ways. It can lower ... at www.hormone.org/Spanish . Proven Weight Loss Methods Fact Sheet www.hormone.org

  15. Weight savings in aerospace vehicles through propellant scavenging

    Science.gov (United States)

    Schneider, Steven J.; Reed, Brian D.

    1988-01-01

    Vehicle payload benefits of scavenging hydrogen and oxygen propellants are addressed. The approach used is to select a vehicle and a mission and then select a scavenging system for detailed weight analysis. The Shuttle 2 vehicle on a Space Station rendezvous mission was chosen for study. The propellant scavenging system scavenges liquid hydrogen and liquid oxygen from the launch propulsion tankage during orbital maneuvers and stores them in well insulated liquid accumulators for use in a cryogenic auxiliary propulsion system. The fraction of auxiliary propulsion propellant which may be scavenged for propulsive purposes is estimated to be 45.1 percent. The auxiliary propulsion subsystem dry mass, including the proposed scavenging system, an additional 20 percent for secondary structure, an additional 5 percent for electrical service, a 10 percent weight growth margin, and 15.4 percent propellant reserves and residuals is estimated to be 6331 kg. This study shows that the fraction of the on-orbit vehicle mass required by the auxiliary propulsion system of this Shuttle 2 vehicle using this technology is estimated to be 12.0 percent compared to 19.9 percent for a vehicle with an earth-storable bipropellant system. This results in a vehicle with the capability of delivering an additional 7820 kg to the Space Station.

  16. Weight savings in aerospace vehicles through propellant scavenging

    Science.gov (United States)

    Schneider, Steven J.; Reed, Brian D.

    1988-05-01

    Vehicle payload benefits of scavenging hydrogen and oxygen propellants are addressed. The approach used is to select a vehicle and a mission and then select a scavenging system for detailed weight analysis. The Shuttle 2 vehicle on a Space Station rendezvous mission was chosen for study. The propellant scavenging system scavenges liquid hydrogen and liquid oxygen from the launch propulsion tankage during orbital maneuvers and stores them in well insulated liquid accumulators for use in a cryogenic auxiliary propulsion system. The fraction of auxiliary propulsion propellant which may be scavenged for propulsive purposes is estimated to be 45.1 percent. The auxiliary propulsion subsystem dry mass, including the proposed scavenging system, an additional 20 percent for secondary structure, an additional 5 percent for electrical service, a 10 percent weight growth margin, and 15.4 percent propellant reserves and residuals is estimated to be 6331 kg. This study shows that the fraction of the on-orbit vehicle mass required by the auxiliary propulsion system of this Shuttle 2 vehicle using this technology is estimated to be 12.0 percent compared to 19.9 percent for a vehicle with an earth-storable bipropellant system. This results in a vehicle with the capability of delivering an additional 7820 kg to the Space Station.

  17. Teens join the MoEDAL collaboration

    CERN Multimedia

    Stephanie Hills

    2013-01-01

    The principal investigator for any institute joining an experimental collaboration is generally a self-assured researcher with evident leadership skills and an in-depth knowledge of their subject gained over many years. Katherine Evans fits the brief in every respect, except that she is 17 years old and her research institute is the Langton Star Centre, based at the Simon Langton Grammar School for Boys. The school has just joined the MoEDAL experiment.   Teacher Becky Parker (left) with two students from the Simon Langton Grammar School for Boys in the MoEDAL experimental area. MoEDAL, the latest LHC experiment has detectors located close to the interaction point of the LHCb experiment. This new experiment is designed to search for the highly ionizing avatars of new physics at the LHC, specifically the magnetic monopole or dyon and other highly ionizing stable massive particles from a number of beyond-the-Standard-Model scenarios. MoEDAL was approved in 2010 and is due to start taking data i...

  18. Ventilation system for 99Mo production apparatus

    International Nuclear Information System (INIS)

    Izumo, Mishiroku; Okane, Shougo; Sorita, Takami; Aoyama, Saburou

    1978-04-01

    In production of 20 Ci 99 Mo from 235 U fission, about 120 Ci of radioiodine ( 131 I, 132 I, and 133 I) is involved. To remove airborne radioiodine from the exhaust air from production apparatus and minimize radioiodine release to the atmosphere, the ventilation system is equipped with 2 units of Model-FD charcoal filter (KI 3 -Impregnated charcoal 2 inch thick of Barnebey-Cheney Co.). From September 1976 to December 1977, 21 runs of 99 Mo production involving airborne radioiodine were carried out. The ventilation system was operated continuously for the whole 15 months period; variation in removal efficiency of airborne radioiodine from the exhaust air stream was observed. In the runs valuable experiences were gained in operation and maintenance of the ventilation system including activated charcoal filter and health-physics management of such facility. Following are the results: (1) Airborne radioiodine from 99 Mo production apparatus is reduced to 10 -3 % of the original quantity. (2) When the ventilation system is operated at a maximum air flow rate through the filter, the average efficiency during 15 months is over 98%. (3) Airborne radioiodine released from 99 Mo production apparatus to the ventilation system is less than 5% particulate iodine and alkyl iodines and more than 95% inorganic iodine. (4) Airborne radioiodine released from the stack is less than 28 μCi/run, which is below the limit in regulations on Radioisotope Production Laboratory. (auth.)

  19. Analysis of MoDOT communication and outreach effectiveness

    Science.gov (United States)

    2008-07-01

    Personal interviews were held with MoDOT personnel to assess MoDOTs current communication practices and existing customer segmentation practices. Focus groups were then held to help gauge the effectiveness of existing communication practices and t...

  20. Fixation Of Mo In Uranium Leach Liquor By Activated Carbon

    International Nuclear Information System (INIS)

    Mainar, S.; Guswita, A.; Erni, R.A.; Susilaningtyas

    1996-01-01

    The use of activated carbon for Mo fixation by bulk system is reported. Several factors influencing the fixation process were examined, including contact time, carbon particle size, carbon porosity and the effect of other elements present in Mo containing solutions. Experimental data showed that an adsorption equilibrium of Mo on of activated carbon and 0,85 to 1,18 mm of carbon particle size under forced-convection mass transfer in 100 ml solution that contains + 0,56 m mol of Mo and +. 0,25 m mol Of U was reached after 6 hours period. Under those conditions, about 0,50 m mol of Mo and 0,026 m mol of U were adsorbed into carbon. High concentration of rare earth elements decreased Mo adsorption, hence, the use of activated carbon was not effective to separate Mo from the digestion liquor of Rirang are where Mo was adsorbed, into the carbon + 34,5 %

  1. X-ray fluorescence analysis of Fe - Ni - Mo systems

    International Nuclear Information System (INIS)

    Belyaev, E.E.; Ershov, A.V.; Mashin, A.I.; Mashin, N.I.; Rudnevskij, N.K.

    1998-01-01

    Procedures for the X-ray fluorescence determination of the composition and thickness of Fe - Ni - Mo thin films and the concentration of elements in thick films of the Fe - Ni - Mo alloy are developed [ru

  2. Interdiffusion between U(Mo,Pt) or U(Mo,Zr) and Al or Al A356 alloy

    International Nuclear Information System (INIS)

    Komar Varela, C.; Mirandou, M.; Arico, S.; Balart, S.; Gribaudo, L.

    2009-01-01

    Solid state reactions in chemical diffusion couples U-7 wt.%Mo-0.9 wt.%Pt/Al at 580 deg. C and U-7 wt.%Mo-0.9 wt.%Pt/Al A356 alloy, U-7 wt.%Mo-1 wt.%Zr/Al and U-7 wt.%Mo-1 wt.%Zr/Al A356 alloy at 550 deg. C were characterized. Results were obtained from optical and scanning electron microscopy, electron probe microanalysis and X-ray diffraction. The UAl 3, UAl 4 and Al 20 Mo 2 U phases were identified in the interaction layers of γU(Mo,Pt)/Al and γU(Mo,Zr)/Al diffusion couples. Al 43 Mo 4 U 6 ternary compound was also identified in γU(Mo,Zr)/Al due to the decomposition of γU(Mo,Zr) phase. The U(Al,Si) 3 and U 3 Si 5 phases were identified in the interaction layers of γU(Mo,Pt)/Al A356 and γU(Mo,Zr)/Al A356 diffusion couples. These phases are formed due to the migration of Si to the interaction layer. In the diffusion couple U(Mo,Zr)/Al A356, Zr 5 Al 3 phase was also identified in the interaction layer. The use of synchrotron radiation at Brazilian Synchrotron Light Laboratory (LNLS, CNPq, Campinas, Brazil) was necessary to achieve a complete crystallographic characterization.

  3. Transfer matrix approach to electron transport in monolayer MoS2/MoO x heterostructures

    Science.gov (United States)

    Li, Gen

    2018-05-01

    Oxygen plasma treatment can introduce oxidation into monolayer MoS2 to transfer MoS2 into MoO x , causing the formation of MoS2/MoO x heterostructures. We find the MoS2/MoO x heterostructures have the similar geometry compared with GaAs/Ga1‑x Al x As semiconductor superlattice. Thus, We employ the established transfer matrix method to analyse the electron transport in the MoS2/MoO x heterostructures with double-well and step-well geometries. We also considere the coupling between transverse and longitudinal kinetic energy because the electron effective mass changes spatially in the MoS2/MoO x heterostructures. We find the resonant peaks show red shift with the increasing of transverse momentum, which is similar to the previous work studying the transverse-momentum-dependent transmission in GaAs/Ga1‑x Al x As double-barrier structure. We find electric field can enhance the magnitude of peaks and intensify the coupling between longitudinal and transverse momentums. Moreover, higher bias is applied to optimize resonant tunnelling condition to show negative differential effect can be observed in the MoS2/MoO x system.

  4. Effect of Mo/B atomic ratio on the properties of Mo2NiB2-based cermets

    International Nuclear Information System (INIS)

    Xie, Lang; Li, XiaoBo; Zhang, Dan; Yi, Li; Gao, XiaoQing; Xiangtan Univ.

    2015-01-01

    Using three elementary substances, Mo, Ni, and amorphous B as raw materials, four series of Mo 2 NiB 2 -based cermets with the Mo/B atomic ratio ranging from 0.9 to 1.2 were successfully prepared via reaction sintering. The effect of Mo/B atomic ratio on the microstructure and properties was studied for the cermets. The results indicate that there is a strong correlation between the Mo/B atomic ratio and properties. The transverse rupture strength of the cermets increases with an increase in Mo/B ratio and shows a maximum value of 1 872 MPa at an Mo/B atomic ratio of 1.1 and then decreases with increasing Mo/B atomic ratio. The hardness and the corrosion resistance of the cermets increase monotonically with an increase in Mo/B atomic ratio. In Mo-rich cermets with an atomic ratio of Mo/B above 1.1, a small amount Ni-Mo intermetallic compound is found precipitated at the interface of Mo 2 NiB 2 grains.

  5. 48 CFR 245.7309-8 - Variations in quantity or weight.

    Science.gov (United States)

    2010-10-01

    ... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

  6. Phase transitions in alloys of the Ni-Mo system

    International Nuclear Information System (INIS)

    Ustinovshikov, Y.; Shabanova, I.

    2011-01-01

    Graphical abstract: The structure of Ni-20 at.% Mo and Ni-25 at.% Mo alloys was studied by methods of TEM and XPS. It is shown that at high temperatures the tendency toward phase separation takes place in the alloys and crystalline bcc Mo particles precipitate in the liquid solution. At 900 deg. C and below, the tendency toward ordering leads to the dissolution of Mo particles and precipitation of the particles of Ni 3 Mo, Ni 2 Mo or Ni 4 Mo chemical compounds. Highlights: → 'Chemical' phase transition 'ordering-phase separation' is first discovered in alloys of the Ni-Mo system. → It is first shown that the phase separation in the alloys studied begins at temperatures above the liquidus one. → The formation of Ni 3 Mo from A1 has gone through the intervening stage of the Ni 4 Mo and Ni 2 Mo coexistence. - Abstract: The structure of Ni-20 at.% Mo and Ni-25 at.% Mo alloys heat treated at different temperatures was studied by the method of transmission electron microscopy. X-ray photoelectron spectroscopy was used to detect the sign of the chemical interaction between Ni and Mo atoms at different temperatures. It is shown that at high temperatures the tendency toward phase separation takes place. The system of additional reflections at positions {1 1/2 0} on the electron diffraction patterns testifies that the precipitation of crystalline bcc Mo particles begins in the liquid solution. At 900 deg. C and below, the tendency toward ordering leads to the precipitation of the particles of the chemical compounds. A body-centered tetragonal phase Ni 4 Mo (D1 a ) is formed in the Ni-20 at.% Mo alloy. In the Ni-25 at.% Mo alloy, the formation of the Ni 3 Mo (D0 22 ) chemical compound from the A1 solid solution has gone through the intervening stage of the Ni 4 Mo (D1 a ) and Ni 2 Mo (Pt 2 Mo) formation.

  7. Comparison between a commercial solid-phase extraction cartridge and a home-made silver containing charcoal column: purification of Mo-99 from I-131 and Te-121

    International Nuclear Information System (INIS)

    Dias, Carla Roberta; Teodoro, Rodrigo; Osso Junior, Joao

    2011-01-01

    Among the radioisotopes used for medical application in Nuclear Medicine, 99m Tc, readily available from the elution of 99 Mo/ 99m Tc generators, is the most used, responsible for more than eighty percent of the total applications. These generators use the 99 Mo radioisotope that is produced in nuclear reactors and IPEN imports all the 99 Mo used in Brazil, mainly from Canada (Nordion). Due to the increasing needs of the Nuclear Medicine in Brazil and the world shortage of 99 Mo observed since 2008, IPEN decided to construct a new research reactor named Brazilian Multipurpose Reactor (BMR) as well as to develop the production of 99 Mo through the route of 235 U fission using a CINTICHEM modified separation process. The 99 Mo obtained from this process contains some contaminants and need to be purified. The aim of this work is to compare the preliminary results of the purification step of the solution containing 99 Mo and the contaminants, 131 I and 121 Te in the silver containing charcoal column and a solid-phase extraction cartridge. The purification process of 99 Mo coming from fission LEU foils was performed by adsorption chromatography using a home-made activated charcoal containing silver column (AC-Ag) and a commercial solid-phase extraction cartridge (OnGuard II Ag). High yields of 99 Mo elution and high retention of 131 I were achieved in the AC-Ag column and silver cartridge but 121 Te was more retained in the cartridge than in the AC-Ag column. (author)

  8. Interstitial Mo-Assisted Photovoltaic Effect in Multilayer MoSe2 Phototransistors.

    Science.gov (United States)

    Kim, Sunkook; Maassen, Jesse; Lee, Jiyoul; Kim, Seung Min; Han, Gyuchull; Kwon, Junyeon; Hong, Seongin; Park, Jozeph; Liu, Na; Park, Yun Chang; Omkaram, Inturu; Rhyee, Jong-Soo; Hong, Young Ki; Yoon, Youngki

    2018-03-01

    Thin-film transistors (TFTs) based on multilayer molybdenum diselenide (MoSe 2 ) synthesized by modified atmospheric pressure chemical vapor deposition (APCVD) exhibit outstanding photoresponsivity (103.1 A W -1 ), while it is generally believed that optical response of multilayer transition metal dichalcogenides (TMDs) is significantly limited due to their indirect bandgap and inefficient photoexcitation process. Here, the fundamental origin of such a high photoresponsivity in the synthesized multilayer MoSe 2 TFTs is sought. A unique structural characteristic of the APCVD-grown MoSe 2 is observed, in which interstitial Mo atoms exist between basal planes, unlike usual 2H phase TMDs. Density functional theory calculations and photoinduced transfer characteristics reveal that such interstitial Mo atoms form photoreactive electronic states in the bandgap. Models indicate that huge photoamplification is attributed to trapped holes in subgap states, resulting in a significant photovoltaic effect. In this study, the fundamental origin of high responsivity with synthetic MoSe 2 phototransistors is identified, suggesting a novel route to high-performance, multifunctional 2D material devices for future wearable sensor applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Electron microscopy studies on MoS2 nanocrystals

    DEFF Research Database (Denmark)

    Hansen, Lars Pilsgaard

    Industrial-style MoS2-based hydrotreating catalysts are studied using electron microscopy. The MoS2 nanostructures are imaged with single-atom sensitivity to reveal the catalytically important edge structures. Furthermore, the in-situ formation of MoS2 crystals is imaged for the first time....

  10. Ternary alloying study of MoSi2

    International Nuclear Information System (INIS)

    Yi, D.; Li, C.; Akselsen, O.M.; Ulvensoen, J.H.

    1998-01-01

    Ternary alloying of MoSi 2 with adding a series of transition elements was investigated by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy (TEM), and energy dispersive spectroscopy (EDS). Iron, Co, Ni, Cr, V, Ti, and Nb were chosen as alloying elements according to the AB 2 structure map or the atomic size factor. The studied MoSi 2 base alloys were prepared by the arc melting process from high-purity metals. The EDS analysis showed that Fe, Co, and Ni have no solid solubility in as-cast MoSi 2 , while Cr, V, Ti, and Nb exhibit limited solid solubilities, which were determined to be 1.4 ± 0.7, 1.4 ± 0.4, 0.4 ± 0.1, and 0.8 ± 0.1. Microstructural characterization indicated that Mo-Si-M VIII (M VIII = Fe, Co, Ni) and Mo-Si-Cr alloys have a two-phase as-cast microstructure, i.e., MoSi 2 matrix and the second-phase FeSi 2 , CoSi, NiSi 2 , and CrSi 2 , respectively. In as-cast Mo-Si-V, Mo-Si-Ti, and Mo-Si-Nb alloys, besides MoSi 2 and C40 phases, the third phases were observed, which have been identified to be (Mo, V) 5 Si 3 , TiSi 2 , and (Mo, Nb) 5 Si 3

  11. 76 FR 43576 - Amendment of Class E Airspace; Hannibal, MO

    Science.gov (United States)

    2011-07-21

    ...-0046; Airspace Docket No. 11-ACE-1] Amendment of Class E Airspace; Hannibal, MO AGENCY: Federal... Hannibal, MO. Decommissioning of the Hannibal non-directional beacon (NDB) at Hannibal Regional Airport, Hannibal, MO, has made this action necessary to enhance the safety and management of Instrument Flight Rule...

  12. Demonstration of resonant photopumping of Mo VII by Mo XII for a VUV laser near 600 Angstrom

    International Nuclear Information System (INIS)

    Ilcisin, K.J.; Aumayr, F.; Schwob, J.L.; Suckewer, S.

    1993-09-01

    We present data of experiments on the resonant photopumping of Mo VII by Mo XII as a method of generating a coherent VUV source near 600 angstrom. The experiment is based on a scheme proposed by Feldman and Reader in which the 4p 6 -- 4p 5 6s transition in Mo VII in resonantly photopumped by the 5s 2 S 1/2 -- 4p 2 P 1/2 transition in Mo XII. Results of the laser produced plasma experiments show the successful enhancement of the population of the Mo VII 4p 5 6s upper lasing level when pumped by an adjacent Mo VII plasma. No enhancement was seen in a control experiment where the Mo VII plasma was pumped by a Zr X plasma. Improvements of the intensity of the Mo XII pump source, achieved using an additional pump laser, lead to the generation of a population inversion for the VUV transition

  13. Weight loss after bariatric surgery in obese adolescents: a systematic review and meta-analysis.

    Science.gov (United States)

    Pedroso, Felipe E; Angriman, Federico; Endo, Atsushi; Dasenbrock, Hormuzdiyar; Storino, Alessandra; Castillo, Ricardo; Watkins, Ammara A; Castillo-Angeles, Manuel; Goodman, Julie E; Zitsman, Jeffrey L

    2018-03-01

    Of adolescents in the United States, 20% have obesity and current treatment options prioritize intensive lifestyle interventions that are largely ineffective. Bariatric surgery is increasingly being offered to obese adolescent patients; however, large-scale effectiveness data is lacking. We used MEDLINE, Embase, and Cochrane databases, and a manual search of references to conduct a systematic review and meta-analysis on overall weight loss after gastric band, gastric sleeve, and gastric bypass in obese adolescent patients (age ≤19) and young adults (age ≤21) in separate analyses. We provided estimates of absolute change in body mass index (BMI, kg/m 2 ) and percent excess weight loss across 4 postoperative time points (6, 12, 24, and 36 mo) for each surgical subgroup. Study quality was assessed using a 10 category scoring system. Data were extracted from 24 studies with 4 having multiple surgical subgroups (1 with 3, and 3 with 2 subgroups), totaling 29 surgical subgroup populations (gastric band: 16, gastric sleeve: 5, gastric bypass: 8), and 1928 patients (gastric band: 1010, gastric sleeve: 139, gastric bypass: 779). Mean preoperative BMI (kg/m 2 ) was 45.5 (95% confidence interval [CI]: 44.7, 46.3) in gastric band, 48.8 (95%CI: 44.9, 52.8) in gastric sleeve, and 53.3 (95%CI: 50.2, 56.4) in gastric bypass patients. The short-term weight loss, measured as mean (95%CI) absolute change in BMI (kg/m 2 ) at 6 months, was -5.4 (-3.0, -7.8) after gastric band, -11.5 (-8.8, -14.2) after gastric sleeve, and -18.8 (-10.9, -26.6) after gastric bypass. Weight loss at 36 months, measured as mean (95%CI) absolute change in BMI (kg/m 2 ) was -10.3 (-7.0, -13.7) after gastric band, -13.0 (-11.0, -15.0) after gastric sleeve, and -15.0 (-13.5, -16.5) after gastric bypass. Bariatric surgery in obese adolescent patients is effective in achieving short-term and sustained weight loss at 36 months; however, long-term data remains necessary to better understand its long

  14. Residual volume on land and when immersed in water: effect on percent body fat.

    Science.gov (United States)

    Demura, Shinichi; Yamaji, Shunsuke; Kitabayashi, Tamotsu

    2006-08-01

    There is a large residual volume (RV) error when assessing percent body fat by means of hydrostatic weighing. It has generally been measured before hydrostatic weighing. However, an individual's maximal exhalations on land and in the water may not be identical. The aims of this study were to compare residual volumes and vital capacities on land and when immersed to the neck in water, and to examine the influence of the measurement error on percent body fat. The participants were 20 healthy Japanese males and 20 healthy Japanese females. To assess the influence of the RV error on percent body fat in both conditions and to evaluate the cross-validity of the prediction equation, another 20 males and 20 females were measured using hydrostatic weighing. Residual volume was measured on land and in the water using a nitrogen wash-out technique based on an open-circuit approach. In water, residual volume was measured with the participant sitting on a chair while the whole body, except the head, was submerged . The trial-to-trial reliabilities of residual volume in both conditions were very good (intraclass correlation coefficient > 0.98). Although residual volume measured under the two conditions did not agree completely, they showed a high correlation (males: 0.880; females: 0.853; P body fat computed using residual volume measured in both conditions was very good for both sexes (males: r = 0.902; females: r = 0.869, P body fat: -3.4 to 2.2% for males; -6.3 to 4.4% for females). We conclude that if these errors are of no importance, residual volume measured on land can be used when assessing body composition.

  15. History of Smoking and Postcessation Weight Gain among Weight Loss Surgery Candidates

    Science.gov (United States)

    Levine, Michele D.; Kalarchian, Melissa A.; Courcoulas, Anita P.; Wisinski, Meghan S.C.; Marcus, Marsha D.

    2007-01-01

    Smoking cessation often results in weight gain. Although smoking cessation frequently is recommended to patients presenting for weight loss surgery (WLS), the relationship between smoking cessation and weight gain among WLS candidates is poorly understood. Thus, we sought to document the history and prevalence of smoking and smoking-related weight gain among WLS candidates. Subjects (N = 67) presenting for bariatric surgery provided demographic information, were interviewed about smoking, and weighed and measured prior to operation. Sixty-seven percent of patients reported a lifetime history of smoking, and 26.9% were current smokers. Among lifetime smokers who had attempted to quit, the average maximum amount of weight gained following smoking cessation was 28.1 pounds, but there was wide variability in postcessation weight gain. These data suggest that smoking among candidates for bariatric surgery is prevalent, and that previous cessation attempts were associated with considerable weight gain. Because patients often receive recommendations to quit smoking and lose weight prior to surgery, additional information on the impact of presurgical smoking cessation on long-tem weight control in this population is needed. PMID:17408868

  16. Optimization of Gad Pattern with Geometrical Weight

    International Nuclear Information System (INIS)

    Chang, Do Ik; Woo, Hae Seuk; Choi, Seong Min

    2009-01-01

    The prevailing burnable absorber for domestic nuclear power plants is a gad fuel rod which is used for the partial control of excess reactivity and power peaking. The radial peaking factor, which is one of the critical constraints for the plant safety depends largely on the number of gad bearing rods and the location of gad rods within fuel assembly. Also the concentration of gad, UO 2 enrichment in the gad fuel rod, and fuel lattice type play important roles for the resultant radial power peaking. Since fuel is upgraded periodically and longer fuel cycle management requires more burnable absorbers or higher gad weight percent, it is required frequently to search for the optimized gad patterns, i.e., the distribution of gad fuel rods within assembly, for the various fuel environment and fuel management changes. In this study, the gad pattern optimization algorithm with respect to radial power peaking factor using geometrical weight is proposed for a single gad weight percent, in which the candidates of the optimized gad pattern are determined based on the weighting of the gad rod location and the guide tube. Also the pattern evaluation is performed systematically to determine the optimal gad pattern for the various situation

  17. Health plan auditing: 100-percent-of-claims vs. random-sample audits.

    Science.gov (United States)

    Sillup, George P; Klimberg, Ronald K

    2011-01-01

    The objective of this study was to examine the relative efficacy of two different methodologies for auditing self-funded medical claim expenses: 100-percent-of-claims auditing versus random-sampling auditing. Multiple data sets of claim errors or 'exceptions' from two Fortune-100 corporations were analysed and compared to 100 simulated audits of 300- and 400-claim random samples. Random-sample simulations failed to identify a significant number and amount of the errors that ranged from $200,000 to $750,000. These results suggest that health plan expenses of corporations could be significantly reduced if they audited 100% of claims and embraced a zero-defect approach.

  18. Comparative evaluation of PSA-Density, percent free PSA and total PSA

    OpenAIRE

    Ströbel, Greta

    2010-01-01

    BACKGROUND The objective of this study was to evaluate the prostate specific antigen (PSA) density (PSAD) (the quotient of PSA and prostate volume) compared with the percent free PSA (%fPSA) and total PSA (tPSA) in different total PSA (tPSA) ranges from 2 ng/mL to 20 ng/mL. Possible cut-off levels depending on the tPSA should be established. METHODS In total, 1809 men with no pretreatment of the prostate were enrolled between 1996 and 2004. Total and free PSA were measured with t...

  19. Controllable synthesis of carbon nanotubes by changing the Mo content in bimetallic Fe-Mo/MgO catalyst

    International Nuclear Information System (INIS)

    Xu Xiangju; Huang Shaoming; Yang Zhi; Zou Chao; Jiang Junfan; Shang Zhijie

    2011-01-01

    Research highlights: → Increasing the Mo content in the Fe-Mo/MgO catalysts resulted in an increase in wall number, diameter and growth yield of carbon nanotubes. → The Fe interacts with MgO to form complex (MgO) x (FeO) 1-x (0 4 and relative large metal Mo particles can be generated after reduction. → The avalanche-like reduction of MgMoO 4 makes the catalyst particles to be small thus enhances the utilize efficiency of Fe nanoparticles. - Abstract: A series of Fe-Mo/MgO catalysts with different Mo content were prepared by combustion method and used as catalysts for carbon nanotube (CNT) growth. Transmission electron microscopy studies of the nanotubes show that the number of the CNT walls and the CNT diameters increase with the increasing of Mo content in the bimetallic catalyst. The growth yield determined by thermogravimetric analysis also follows the trend: the higher the Mo content, the higher the yield of the CNTs. However, the increase of Mo content leads to the lower degree of graphitization of CNTs. A comparative study on the morphology and catalytic functions of Fe/MgO, Mo/MgO and Fe-Mo/MgO catalysts was carried out by scanning electron microscopy and X-ray diffraction. It is found that the Fe interacts with MgO to form complexes and is then dispersed into the MgO support uniformly, resulting in very small Fe nanoparticles after reduction. The Mo interacts with MgO to form stoichiometry compound MgMoO 4 and relative large metal Mo particles can be generated after reduction. High yield CNTs with small diameter can be generated from Fe-Mo/MgO because the avalanche-like reduction of MgMoO 4 makes the catalyst particles to be small thus enhances the utilize efficiency of Fe nanoparticles.

  20. Moderate carbohydrate, moderate protein weight loss diet reduces cardiovascular disease risk compared to high carbohydrate, low protein diet in obese adults: A randomized clinical trial

    Directory of Open Access Journals (Sweden)

    Evans Ellen M

    2008-11-01

    Full Text Available Abstract Background To evaluate the metabolic effects of two weight loss diets differing in macronutrient composition on features of dyslipidemia and post-prandial insulin (INS response to a meal challenge in overweight/obese individuals. Methods This study was a parallel-arm randomized 4 mo weight loss trial. Adults (n = 50, 47 ± 7 y matched on BMI (33.6 ± 0.6 kg/m2, P = 0.79 consumed energy restricted diets (deficit ~500 kcal/d: PRO (1.6 g.kg-1.d-1 protein and -1.d-1 protein and > 220 g/d carbohydrate for 4 mos. Meal challenges of respective diets were utilized for determination of blood lipids and post-prandial INS and glucose response at the beginning and end of the study. Results There was a trend for PRO to lose more weight (-9.1% vs. -7.3%, P = 0.07 with a significant reduction in percent fat mass compared to CHO (-8.7% vs. -5.7%; P = 0.03. PRO also favored reductions in triacylglycerol (-34% vs. -14%; P P = 0.05; however, CHO favored reduction in LDL-C (-7% vs. +2.5%; P P P Conclusion A weight loss diet with moderate carbohydrate, moderate protein results in more favorable changes in body composition, dyslipidemia, and post-prandial INS response compared to a high carbohydrate, low protein diet suggesting an additional benefit beyond weight management to include augmented risk reduction for metabolic disease.

  1. A systematic first principle method to study magnetic properties of FeMo, CoMo and NiMo

    International Nuclear Information System (INIS)

    Bhattacharjee, Ashis Kumar; Touheed, Md.; Ahmed, Mesbahuddin; Halder, A.; Mookerjee, A.

    2003-06-01

    We use the first principle TB-LMTO (Tight-Binding Linear Muffin Tin Orbital) method combined with the ASM (Augmented Space Method) to take care of disorder beyond the mean field (CPA - Cohetent Potential Approximation) approximation. We analyze binary alloys between magnetic transition metals Fe, Co, Ni and non-magnetic Mo to find out the effect of disorder on electronic structure and consequently magnetic properties of the alloys. (author)

  2. High pressure effect on MoS2 and MoSe2 single crystals grown by ...

    Indian Academy of Sciences (India)

    Unknown

    tetrahedral anvil apparatus up to 5 GPa. In this paper we report room temperature resistance mea- surements as a function of pressure on MoS2 and MoSe2 single crystals. In each case the resistance decreases un- der pressure due to an increase in the carrier concentration. 2. Experimental. Single crystals of MoS2 and ...

  3. Body Mass Index, percent body fat, and regional body fat distribution in relation to leptin concentrations in healthy, non-smoking postmenopausal women in a feeding study

    Directory of Open Access Journals (Sweden)

    Campbell William

    2007-01-01

    Full Text Available Abstract Background The relationship between BMI and leptin has been studied extensively in the past, but previous reports in postmenopausal women have not been conducted under carefully controlled dietary conditions of weight maintenance using precise measures of body fat distribution. The aim of the present study was to examine the association between serum leptin concentration and adiposity as estimated by BMI and dual energy x-ray absorptiometry (DEXA measures (percent body fat, central and peripheral fat, and lean mass in postmenopausal women. Methods This study was conducted as a cross-sectional analysis within the control segment of a randomized, crossover trial in which postmenopausal women (n = 51 consumed 0 (control, 15 (one drink, and 30 (two drinks g alcohol (ethanol/d for 8 weeks as part of a controlled diet. BMIs were determined and DEXA scans were administered to the women during the 0 g alcohol treatment, and a blood sample was collected at baseline and week 8 of each study period for leptin analysis. Results and discussion In multivariate analysis, women who were overweight (BMI > 25 to ≤ 30 kg/m2 had a 2-fold increase, and obese women (BMI > 30 kg/m2 had more than a 3-fold increase in serum leptin concentrations compared to normal weight (BMI ≤25 kg/m2 women. When the models for the different measures of adiposity were assessed by multiple R2, models which included percent body fat explained the highest proportion (approximately 80% of the serum leptin variance. Conclusion Under carefully controlled dietary conditions, we confirm that higher levels of adiposity were associated with higher concentrations of serum leptin. It appears that percent body fat in postmenopausal women may be the best adiposity-related predictor of serum leptin.

  4. Running speed during training and percent body fat predict race time in recreational male marathoners.

    Science.gov (United States)

    Barandun, Ursula; Knechtle, Beat; Knechtle, Patrizia; Klipstein, Andreas; Rüst, Christoph Alexander; Rosemann, Thomas; Lepers, Romuald

    2012-01-01

    Recent studies have shown that personal best marathon time is a strong predictor of race time in male ultramarathoners. We aimed to determine variables predictive of marathon race time in recreational male marathoners by using the same characteristics of anthropometry and training as used for ultramarathoners. Anthropometric and training characteristics of 126 recreational male marathoners were bivariately and multivariately related to marathon race times. After multivariate regression, running speed of the training units (β = -0.52, P marathon race times. Marathon race time for recreational male runners may be estimated to some extent by using the following equation (r (2) = 0.44): race time ( minutes) = 326.3 + 2.394 × (percent body fat, %) - 12.06 × (speed in training, km/hours). Running speed during training sessions correlated with prerace percent body fat (r = 0.33, P = 0.0002). The model including anthropometric and training variables explained 44% of the variance of marathon race times, whereas running speed during training sessions alone explained 40%. Thus, training speed was more predictive of marathon performance times than anthropometric characteristics. The present results suggest that low body fat and running speed during training close to race pace (about 11 km/hour) are two key factors for a fast marathon race time in recreational male marathoner runners.

  5. Relationship between depression with FEV1 percent predicted and BODE index in chronic obstructive pulmonary disease

    Science.gov (United States)

    Gunawan, H.; Hanum, H.; Abidin, A.; Hanida, W.

    2018-03-01

    WHO reported more than 3 million people die from COPD in 2012 and are expected to rank third after cardiovascular and cancer diseases in the future. Recent studies reported the prevalence of depression in COPD patients was higher than in control group. So, it’s important for clinicians to understand the relationship of depression symptoms with clinical aspects of COPD. For determining the association of depression symptoms with lung function and BODE index in patients with stable COPD, a cross-sectional study was in 98 stable COPD outpatients from January to June 2017. Data were analyzed using Independent t-test, Mann-Whitney test, and Spearman’s rank correlation. COPD patients with depression had higher mMRC scores, and lower FEV1 percent predicted, and then 6-Minutes Walk Test compared to those without depression. There was a moderate strength of correlation (r=-0.43) between depression symptoms and FEV1 percent predicted, and strong correlation (r=0.614) between depression symptoms and BODE index. It indicates that BODE index is more accurate to describe symptoms of depression in COPD patients.

  6. Fabrication of Z-scheme Ag3PO4/MoS2 composites with enhanced photocatalytic activity and stability for organic pollutant degradation

    International Nuclear Information System (INIS)

    Zhu, Chaosheng; Zhang, Lu; Jiang, Bo; Zheng, Jingtang; Hu, Ping; Li, Sujuan; Wu, Mingbo; Wu, Wenting

    2016-01-01

    Highlights: • Ag 3 PO 4 /MoS 2 composite photocatalysts were prepared by precipitation method. • The composites showed enhanced visible-light photocatalytic activity. • The photocorrosion of Ag 3 PO 4 was inhibited due to the introduction of MoS 2 . • Z-scheme mechanism was proposed to explain the enhanced photoactivity. - Abstract: In this study, highly efficient visible-light-driven Ag 3 PO 4 /MoS 2 composite photocatalysts with different weight ratios of MoS 2 were prepared via the ethanol-water mixed solvents precipitation method and characterized by ICP, XRD, HRTEM, FE-SEM, BET, XPS, UV–vis DRS and PL analysis. Under visible-light irradiation, Ag 3 PO 4 /MoS 2 composites exhibit excellent photocatalytic activity towards the degradation of organic pollutants in aqueous solution. The optimal composite with 0.648 wt% MoS 2 content exhibits the highest photocatalytic activity, which can degrade almost all MB under visible-light irradiation within 60 min. Recycling experiments confirmed that the Ag 3 PO 4 /MoS 2 catalysts had superior cycle performance and stability. The photocatalytic activity enhancement of Ag 3 PO 4 /MoS 2 photocatalysts can be mainly ascribed to the efficient separation of photogenerated charge carriers and the stronger oxidation and reduction ability through a Z-scheme system composed of Ag 3 PO 4 , Ag and MoS 2 , in which Ag particles act as the charge separation center. The high photocatalytic stability is due to the successful inhibition of the photocorrosion of Ag 3 PO 4 by transferring the photogenerated electrons of Ag 3 PO 4 to MoS 2 . The evidence of the Z-scheme photocatalytic mechanism of the composite photocatalysts could be obtained from the active species trapping experiments and the photoluminescence technique.

  7. Weighted network modules

    International Nuclear Information System (INIS)

    Farkas, Illes; Abel, Daniel; Palla, Gergely; Vicsek, Tamas

    2007-01-01

    The inclusion of link weights into the analysis of network properties allows a deeper insight into the (often overlapping) modular structure of real-world webs. We introduce a clustering algorithm clique percolation method with weights (CPMw) for weighted networks based on the concept of percolating k-cliques with high enough intensity. The algorithm allows overlaps between the modules. First, we give detailed analytical and numerical results about the critical point of weighted k-clique percolation on (weighted) Erdos-Renyi graphs. Then, for a scientist collaboration web and a stock correlation graph we compute three-link weight correlations and with the CPMw the weighted modules. After reshuffling link weights in both networks and computing the same quantities for the randomized control graphs as well, we show that groups of three or more strong links prefer to cluster together in both original graphs

  8. Preventing Weight Gain

    Science.gov (United States)

    ... Local Programs Related Topics Diabetes Nutrition Preventing Weight Gain Language: English (US) Español (Spanish) Recommend on Facebook ... cancer. Choosing an Eating Plan to Prevent Weight Gain So, how do you choose a healthful eating ...

  9. Weight management in pregnancy

    OpenAIRE

    Olander, E. K.

    2015-01-01

    Key learning points:\\ud - Women who start pregnancy in an overweight or obese weight category have increased health risks\\ud - Irrespective of pre-pregnancy weight category, there are health risks associated with gaining too much weight in pregnancy for both mother and baby\\ud - There are currently no official weight gain guidelines for pregnancy in the UK, thus focus needs to be on supporting pregnant women to eat healthily and keep active

  10. Evaluating Strengthening and Impact Toughness Mechanisms for Ferritic and Bainitic Microstructures in Nb, Nb-Mo and Ti-Mo Microalloyed Steels

    Directory of Open Access Journals (Sweden)

    Gorka Larzabal

    2017-02-01

    Full Text Available Low carbon microalloyed steels show interesting commercial possibilities by combining different “micro”-alloying elements when high strength and low temperature toughness properties are required. Depending on the elements chosen for the chemistry design, the mechanisms controlling the strengths and toughness may differ. In this paper, a detailed characterization of the microstructural features of three different microalloyed steels, Nb, Nb-Mo and Ti-Mo, is described using mainly the electron backscattered diffraction technique (EBSD as well as transmission electron microscopy (TEM. The contribution of different strengthening mechanisms to yield strength and impact toughness is evaluated, and its relative weight is computed for different coiling temperatures. Grain refinement is shown to be the most effective mechanism for controlling both mechanical properties. As yield strength increases, the relative contribution of precipitation strengthening increases, and this factor is especially important in the Ti-Mo microalloyed steel where different combinations of interphase and random precipitation are detected depending on the coiling temperature. In addition to average grain size values, microstructural heterogeneity is considered in order to propose a new equation for predicting ductile–brittle transition temperature (DBTT. This equation considers the wide range of microstructures analyzed as well as the increase in the transition temperature related to precipitation strengthening.

  11. Study of the activation of targets containing Mo for the production of 99Mo by the 98Mo(n,γ)99Mo nuclear reaction and the behaviour of the radionuclidic impurities of the process

    International Nuclear Information System (INIS)

    Nieto, Renata Correa

    1998-01-01

    The most used radioisotope in Nuclear Medicine is 99m Tc, in the 99 Mo- 99m Tc generator form. 99 Mo can be produced by several nuclear reactions in reactors and cyclotrons. The cyclotron production is not technically and economically viable. The production in the reactor can be done in two different ways: by the fission of 235 U and by 98 Mo(n,γ) 99 Mo reaction. A project for the production of 99 Mo by the activation of Mo and the preparation of gel type generators is under development at the 'Instituto de Pesquisas Energeticas e Nucleares'. In the present work, the radionuclidic impurities produced in the activation of MOO 3 and MoZr gel were evaluated, and these represent the two possible ways of preparing the gel of MoZr. A target of metallic Mo was also studied. The radionuclidic purity of 99m Tc eluted from generators prepared in these ways was also measured and compared with the generators prepared with fission 99 Mo. The results showed that, by all the parameters analysed, the best way of preparing the generator of 99 Mo - 99m Tc is the irradiation of MOO 3 and further preparation of the gel and the generators. (author)

  12. Holey Reduced Graphene Oxide Coupled with an Mo2 N-Mo2 C Heterojunction for Efficient Hydrogen Evolution.

    Science.gov (United States)

    Yan, Haijing; Xie, Ying; Jiao, Yanqing; Wu, Aiping; Tian, Chungui; Zhang, Xiaomeng; Wang, Lei; Fu, Honggang

    2018-01-01

    An in situ catalytic etching strategy is developed to fabricate holey reduced graphene oxide along with simultaneous coupling with a small-sized Mo 2 N-Mo 2 C heterojunction (Mo 2 N-Mo 2 C/HGr). The method includes the first immobilization of H 3 PMo 12 O 40 (PMo 12 ) clusters on graphite oxide (GO), followed by calcination in air and NH 3 to form Mo 2 N-Mo 2 C/HGr. PMo 12 not only acts as the Mo heterojunction source, but also provides the Mo species that can in situ catalyze the decomposition of adjacent reduced GO to form HGr, while the released gas (CO) and introduced NH 3 simultaneously react with the Mo species to form an Mo 2 N-Mo 2 C heterojunction on HGr. The hybrid exhibits superior activity towards the hydrogen evolution reaction with low onset potentials of 11 mV (0.5 m H 2 SO 4 ) and 18 mV (1 m KOH) as well as remarkable stability. The activity in alkaline media is also superior to Pt/C at large current densities (>88 mA cm -2 ). The good activity of Mo 2 N-Mo 2 C/HGr is ascribed to its small size, the heterojunction of Mo 2 N-Mo 2 C, and the good charge/mass-transfer ability of HGr, as supported by a series of experiments and theoretical calculations. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Theoretical calculations of valence states in Fe-Mo compounds

    International Nuclear Information System (INIS)

    Estrada, F; Navarro, O; Noverola, H; Suárez, J R; Avignon, M

    2014-01-01

    The half-metallic ferromagnetic double perovskite compound Sr 2 FeMoO 6 is considered as an important material for spintronic applications. It appears to be fundamental to understand the role of electronic parameters controlling the half-metallic ground state. Fe-Mo double perovskites usually present some degree of Fe/Mo disorder which generally increases with doping. In this work, we study the valence states of Fe-Mo cations in the off-stoichiometric system Sr 2 Fe 1+x Mo 1−x O 6 (−1 ≤ x ≤ 1/3) with disorder. Our results for Fe and Mo valence states are obtained using the Green functions and the renormalization perturbation expansion method. The model is based on a correlated electron picture with localized Fe-spins and conduction Mo-electrons interacting with the local spins via a double-exchange-type mechanism

  14. Phase formation in the Li2MoO4-Rb2MoO4-Ln2(MoO4)3 systems and the properties of LiRbLn2(MoO4)4

    International Nuclear Information System (INIS)

    Basovich, O.M.; Khajkina, E.G.; Vasil'ev, E.V.; Frolov, A.M.

    1995-01-01

    Phase equilibria within subsolidus range of ternary salt systems Li 2 MoO 4 -Rb 2 MoO 4 -Ln 2 (MoO 4 ) 4 (Ln - Nd, Er) are analyzed. Formation of ternary molybdate LiRbNd 2 (MoO 4 ) 4 is proved along LiNd(MoO 4 ) 2 -RbNd(MoO 4 )-2 cross-section. Phase diagram of this cross-section is plotted. Similar compounds are synthesized for Ln = La-Eu. The parameters of their monoclinic elementary cells are determined. Luminescent properties of LiRbLa 2 (MoO 4 ) 4 -Nd 3+ are studied. 17 refs., 4 figs., 2 tabs

  15. Gradient Weight in Phonology

    Science.gov (United States)

    Ryan, Kevin Michael

    2011-01-01

    Research on syllable weight in generative phonology has focused almost exclusively on systems in which weight is treated as an ordinal hierarchy of clearly delineated categories (e.g. light and heavy). As I discuss, canonical weight-sensitive phenomena in phonology, including quantitative meter and quantity-sensitive stress, can also treat weight…

  16. Gestational weight gain.

    Science.gov (United States)

    Kominiarek, Michelle A; Peaceman, Alan M

    2017-12-01

    Prenatal care providers are advised to evaluate maternal weight at each regularly scheduled prenatal visit, monitor progress toward meeting weight gain goals, and provide individualized counseling if significant deviations from a woman's goals occur. Today, nearly 50% of women exceed their weight gain goals with overweight and obese women having the highest prevalence of excessive weight gain. Risks of inadequate weight gain include low birthweight and failure to initiate breast-feeding whereas the risks of excessive weight gain include cesarean deliveries and postpartum weight retention for the mother and large-for-gestational-age infants, macrosomia, and childhood overweight or obesity for the offspring. Prenatal care providers have many resources and tools to incorporate weight and other health behavior counseling into routine prenatal practices. Because many women are motivated to improve health behaviors, pregnancy is often considered the optimal time to intervene for issues related to eating habits and physical activity to prevent excessive weight gain. Gestational weight gain is a potentially modifiable risk factor for a number of adverse maternal and neonatal outcomes and meta-analyses of randomized controlled trials report that diet or exercise interventions during pregnancy can help reduce excessive weight gain. However, health behavior interventions for gestational weight gain have not significantly improved other maternal and neonatal outcomes and have limited effectiveness in overweight and obese women. Copyright © 2017 Elsevier Inc. All rights reserved.

  17. Successful labeling of 99mTc-MDP using 99mTc separated from 99Mo produced by 100Mo(n,2n)99Mo

    International Nuclear Information System (INIS)

    Nagai, Yasuki; Hatsukawa, Yuichi; Kin, Tadahiro; Hashimoto, Kazuyuki; Motoishi, Shoji; Konno, Chikara; Ochiai, Kentaro; Takakura, Kosuke; Sato, Yuichi; Sato, Norihito; Ohta, Akio; Yamabayashi, Hisamichi; Tanase, Masakazu; Fujisaki, Saburo; Kawauchi, Yukimasa; Teranaka, Tomoyuki; Takeuchi, Nobuhiro; Igarashi, Takashi

    2011-01-01

    We have for the first time succeeded in separating 99m Tc from a MoO 3 sample irradiated with accelerator neutrons free from any radioactive impurities and in formulating 99m Tc-methylene diphosphonate ( 99 mTc-MDP). 99 Mo, the mother nuclide of 99m Tc, was produced by the 100 Mo(n,2n) 99 Mo reaction using about 14 MeV neutrons provided by the 3 H(d,n) 4 He reaction at the Fusion Neutronics Source of Japan Atomic Energy Agency. The 99m Tc was separated from 99 Mo by sublimation and its radionuclide purity was confirmed to be higher than 99.99% by γ-spectroscopy. The labeling efficiency of 99m Tc-MDP was shown to be higher than 99% by thin-layer chromatography. These values exceed the United States Pharmacopeia requirements for a fission product, 99 Mo. Consequently, a 99m Tc radiopharmaceutical preparation formed by using the mentioned 99 Mo can be a promising substitute for the fission product 99 Mo, which is currently produced using a highly enriched uranium target in aging research reactors. A longstanding problem to ensure a reliable and constant supply of 99 Mo in Japan can be partially mitigated. (author)

  18. Study of the 93Mo nucleus

    International Nuclear Information System (INIS)

    Mittal, V.K.; Avasthi, D.K.; Kumar, A; Govil, I.M.

    1981-01-01

    The level structure of 93 Mo has been studied through 93 Nb(p,nγ) reaction at incident proton energy of 4.2 MeV. Spin assignments and multipole mixing ratios for various levels and transitions have been deduced from the analysis of angular distributions of singles γ-ray spectra. Lifetimes of various levels have been obtained using Doppler Shift Attenuation (DSA) method. (author)

  19. 48 CFR 252.237-7015 - Loss or damage (weight of articles).

    Science.gov (United States)

    2010-10-01

    ... shall— (1) Be liable for return of the articles furnished for service under this contract; and (2... in servicing the laundry is ____ percent of the weight recorded on delivery tickets when the laundry...

  20. MoS{sub 2} spaser

    Energy Technology Data Exchange (ETDEWEB)

    Jayasekara, Charith, E-mail: charith.jayasekara@monash.edu; Premaratne, Malin [Advanced Computing and Simulation Laboratory (A chi L), Department of Electrical and Computer Systems Engineering, Monash University, Clayton, Victoria 3800 (Australia); Gunapala, Sarath D. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California 91109 (United States); Stockman, Mark I. [Department of Physics and Astronomy, Georgia State University, Atlanta, Georgia 30303 (United States)

    2016-04-07

    We present a comprehensive analysis of a spaser made of a circular shaped highly doped molybdenum disulfide (MoS{sub 2}) resonator. “Spaser” is an acronym for “surface plasmon amplification by stimulated emission of radiation”–a nanoscale source of surface plasmons generated by stimulated emission in a plasmonic resonator which receives energy nonradiatively. By considering localized surface plasmon modes, operation characteristics of the model are analysed, and tunability of the design is demonstrated. We find the optimum geometric and material parameters of the spaser that provides efficient outputs and carryout a comparative analysis with a similar circular spaser made of graphene. Owing to physical and chemical properties of MoS{sub 2} and the active medium, the proposed design delivers efficient outputs in terms of spaser mode energy, operating thresholds, Q-factor, and electric field amplitude. Lower operating thresholds and higher mode energies are notable advantages of the design. Owing to having many superior features to existing similar designs, this MoS{sub 2} spaser may be much suited for applications in nanoplasmonic devices.

  1. Physicochemical investigation of Bi2MoO6 solid-phase interaction with Sm2MoO6

    International Nuclear Information System (INIS)

    Khajkina, E.G.; Kovba, L.M.; Bazarova, Zh.G.; Khal'baeva, K.M.; Khakhinov, V.V.; Mokhosoev, M.V.

    1986-01-01

    Bi 2 MoO 6 -Sm 2 MoO 6 interaction in the temperature range of 700-1000 deg C is studied using X-ray phase analysis and vibrational spectroscopy. Formation of monoclinic solid solutions based on γ'-Bi 2 MoO 6 and B 2-x Sm x MoO 6 varied composition phase with α-Ln 2 MoO 6 structure which homogeneity region extent at 1000 deg C constitutes ∼ 50 mol % (0.7≤x≤1.7) is stated. Crystallographic characteristics of the synthesized phases are determined

  2. Carotid bifurcation calcium and correlation with percent stenosis of the internal carotid artery on CT angiography

    International Nuclear Information System (INIS)

    McKinney, Alexander M.; Casey, Sean O.; Teksam, Mehmet; Truwit, Charles L.; Kieffer, Stephen; Lucato, Leandro T.; Smith, Maurice

    2005-01-01

    The aim of this paper was to determine the correlation between calcium burden (expressed as a volume) and extent of stenosis of the origin of the internal carotid artery (ICA) by CT angiography (CTA). Previous studies have shown that calcification in the coronary arteries correlates with significant vessel stenosis, and severe calcification (measured by CT) in the carotid siphon correlates with significant (greater than 50% stenosis) as determined angiographically. Sixty-one patients (age range 50-85 years) underwent CT of the neck with intravenous administration of iodinated contrast for a variety of conditions. Images were obtained with a helical multidetector array CT scanner and reviewed on a three-dimensional workstation. A single observer manipulated window and level to segment calcified plaque from vascular enhancement in order to quantify vascular calcium volume (cc) in the region of the bifurcation of the common carotid artery/ICA origin, and to measure the extent of ICA stenosis near the origin. A total of 117 common carotid artery bifurcations were reviewed. A ''significant'' stenosis was defined arbitrarily as >40% (to detect lesions before they become hemodynamically significant) of luminal diameter on CTA using NASCET-like criteria. All ''significant'' stenoses (21 out of 117 carotid bifurcations) had measurable calcium. We found a relatively strong correlation between percent stenosis and the calcium volume (Pearson's r= 0.65, P<0.0001). We also found that there was an even stronger correlation between the square root of the calcium volume and the percent stenosis as measured by CTA (r= 0.77, P<0.0001). Calcium volumes of 0.01, 0.03, 0.06, 0.09 and 0.12 cc were used as thresholds to evaluate for a ''significant'' stenosis. A receiver operating characteristic (ROC) curve demonstrated that thresholds of 0.06 cc (sensitivity 88%, specificity 87%) and 0.03 cc (sensitivity 94%, specificity 76%) generated the best combinations of sensitivity and

  3. Synthesis of Fine Mo2C Powder from Prereduced Mo in Undiluted CH4 Flow

    Science.gov (United States)

    Cetinkaya, S.; Eroglu, S.

    2017-10-01

    The carburization behavior of prereduced Mo was investigated in undiluted CH4 flow at 900-1000 K. Prior to the experiments, equilibrium thermodynamic analysis was carried out in the Mo-C-H system. The products were characterized by mass measurement, x-ray diffraction and scanning electron microscopy techniques. A single Mo2C phase was obtained within 45 min, 5 min, and 2.5 min at 900 K, 950 K, and 1000 K, respectively, at CH4 contents higher than the predicted ones. The reasons for this behavior were discussed in terms of CH4 stability, open tube flow, and self-created atmosphere in the powder bed. The fractional conversion-time curves indicated that the carburization kinetics followed a linear rate law. The Mo2C crystallite size (26-37 nm) and platelet thickness (50-100 nm) were found to be smaller than those of the parent Mo phase. These findings were attributable to the defects formed as a result of stresses associated with the reduction and the carburization.

  4. Deoxygenation of glycolaldehyde and furfural on Mo2C/Mo(100)

    Science.gov (United States)

    McManus, Jesse R.; Vohs, John M.

    2014-12-01

    The desire to produce fuels and chemicals in an energy conscious, environmentally sympathetic approach has motivated considerable research on the use of cellulosic biomass feedstocks. One of the major challenges facing the utilization of biomass is finding effective catalysts for the efficient and selective removal of oxygen from the highly-oxygenated, biomass-derived platform molecules. Herein, a study of the reaction pathways for the biomass-derived platform molecule furfural and biomass-derived sugar model compound glycolaldehyde provides insight into the mechanisms of hydrodeoxygenation (HDO) on a model molybdenum carbide catalyst, Mo2C/Mo(100). Using temperature programmed desorption (TPD) and high resolution electron energy loss spectroscopy (HREELS), it was found that the Mo2C/Mo(100) catalyst was active for selective deoxygenation of the aldehyde carbonyl by facilitating adsorption of the aldehyde in an η2(C,O) bonding configuration. Furthermore, the catalyst showed no appreciable activity for furanic ring hydrogenation, highlighting the promise of relatively inexpensive Mo2C catalysts for selective HDO chemistry.

  5. Study of the structural and mechanical properties of the alloy U-0.2V (weight percent) forged in the α phase

    International Nuclear Information System (INIS)

    Couterne, A.; Guillaume, C.

    1980-01-01

    The effects of forging carried out in the 2 phase on the structural properties of the alloy U-0.2V (evtl.%) carburized or not have been studied. A carbon content of the order of 300 x 10 6 , contrary to the one used for the cast alloy, is neither detrimental to the micrographic structure nor to the mechanical properties of the alloy. The forged plates have a semicrystalline structure with alternative, formed bands, on the one hand by small recrystallization grains, on the other by quite deformed coarse grains. The preferential orientations developed resume to a fibrous structure. The fiber axis, practically the [002] axis, is parallell to the normal to the surface of the forged disc. This result implies a good isotropy of the dilatometric and mechanical properities in the whole plane parallel to the disc faces. A correlation has been made between the found structure and the thermal expansion of the material. Furthermore, the mechanical characteristics reach an excellent level (Rsup(M) approx. 900 MPa, A approx. 38%). (orig.)

  6. A fuzzy neural network model to forecast the percent cloud coverage and cloud top temperature maps

    Directory of Open Access Journals (Sweden)

    Y. Tulunay

    2008-12-01

    Full Text Available Atmospheric processes are highly nonlinear. A small group at the METU in Ankara has been working on a fuzzy data driven generic model of nonlinear processes. The model developed is called the Middle East Technical University Fuzzy Neural Network Model (METU-FNN-M. The METU-FNN-M consists of a Fuzzy Inference System (METU-FIS, a data driven Neural Network module (METU-FNN of one hidden layer and several neurons, and a mapping module, which employs the Bezier Surface Mapping technique. In this paper, the percent cloud coverage (%CC and cloud top temperatures (CTT are forecast one month ahead of time at 96 grid locations. The probable influence of cosmic rays and sunspot numbers on cloudiness is considered by using the METU-FNN-M.

  7. Phased Acoustic Array Measurements of a 5.75 Percent Hybrid Wing Body Aircraft

    Science.gov (United States)

    Burnside, Nathan J.; Horne, William C.; Elmer, Kevin R.; Cheng, Rui; Brusniak, Leon

    2016-01-01

    Detailed acoustic measurements of the noise from the leading-edge Krueger flap of a 5.75 percent Hybrid Wing Body (HWB) aircraft model were recently acquired with a traversing phased microphone array in the AEDC NFAC (Arnold Engineering Development Complex, National Full Scale Aerodynamics Complex) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The spatial resolution of the array was sufficient to distinguish between individual support brackets over the full-scale frequency range of 100 to 2875 Hertz. For conditions representative of landing and take-off configuration, the noise from the brackets dominated other sources near the leading edge. Inclusion of flight-like brackets for select conditions highlights the importance of including the correct number of leading-edge high-lift device brackets with sufficient scale and fidelity. These measurements will support the development of new predictive models.

  8. Perceived weight status may contribute to education inequalities in five-year weight change among mid-aged women.

    Science.gov (United States)

    Siu, Jessica; Giskes, Katrina; Shaw, Jonathan; Turrell, Gavin

    2011-06-01

    To examine education differences in five-year weight change among mid-aged adults, and to ascertain if this may be due to socioeconomic differences in perceived weight status or weight control behaviours (WCBs). Data were used from the Australian Diabetes, Obesity and Lifestyle Study. Mid-aged men and women with measured weights at both baseline (1999-2000) and follow-up (2004-2005) were included. Percent weight change over the five-year interval was calculated and perceived weight status, WCBs and highest attained education were collected at baseline. Low-educated men and women were more likely to be obese at baseline compared to their high-educated counterparts. Women with a certificate-level education had a greater five-year weight gain than those with a bachelor degree or higher. Perceived weight status or WCBs did not differ by education among men and women, however participants that perceived themselves as very overweight had less weight gain than those perceiving themselves as underweight or normal weight. WCBs were not associated with five-year weight change. The higher prevalence of overweight/obesity among low-educated women may be a consequence of greater weight gain in mid-adulthood. Education inequalities in overweight/obesity among men and women made be due (in part) to overweight or obese individuals in low-educated groups not perceiving themselves as having a weight problem. © 2011 The Authors. ANZJPH © 2011 Public Health Association of Australia.

  9. Estimation of the volume and percent uptake of the liver and spleen by SPECT

    International Nuclear Information System (INIS)

    Yamagata, Atushi

    1988-01-01

    The volume and percent uptake of the liver and spleen were estimated with single photon emission computed tomography (SPECT) using 99m Tc-phytate. Clinical usefulness of these parameters was evaluated by comparison with other liver function tests in 87 patients including 25 normal controls, 24 liver cirrhosis and 16 other chronic liver diseases. SPECT images were obtained by Maxi Camera 400T. Cut-off level for reconstruction of images and relationship between counts and activity (mCi) were obtained from phantom studies. Volumes estimated using SPECT and computed tomography were compared in 16 patients. Results obtained were as follows. 1) Optimal cut-off level for measurement of volumes for the liver was 37 % and for the spleen was 42 %. 2) Correlation between organ volumes estimated with CT and SPECT was good (r = 0.92 for the liver and r = 0.96 for the spleen), although volumes measured with SPECT were larger than those with CT. 3) Significant differences of percent uptake were observed between normal controls and liver cirrhosis. 4) Better correlation between spleen volumes and uptake was recognized in cases without liver cirrhosis than in cases with liver cirrhosis. The spleen uptake in liver cirrhosis was higher than those in others in comparison with the volume. 5) The liver/spleen ratio of 99m Tc-phytae uptake could most clearly differentiate liver cirrhosis from others. 6) Negative correlation was observed between liver volume or uptake and ICG (R 15 ). Estimation of volume and uptake of the liver and spleen could be a useful procedure to assess liver function, probably related with effective hepatic blood flow in liver cirrhosis. (author)

  10. Thyroid weight with age

    International Nuclear Information System (INIS)

    Raulier-Fabry, C.; Hammer, R.

    1965-01-01

    A large number of data on thyroid weight of euthyroid subjects have been collected from the literature in this study. The most probable average weight of the gland appears to be 20 g in the adult and 2 g in the newborn. A decrease in weight has been observed during the first year of life (1 g at 6 months) and only in the second year of life the initial birth weight is reached again. The weight curve may be considered as consisting of three straight lines: from 2 to 7, from 7 to 18 and from 18 to 25 years, their slopes being respectively 0.6, 0.9 and 0.5 g/year. The variations in weight of the thyroid during adulthood are sufficiently small to consider it as having constant value between 25 and 55 years. The available information points to a negligible weight difference between sexes. (authors) [fr

  11. Yogurt and weight management.

    Science.gov (United States)

    Jacques, Paul F; Wang, Huifen

    2014-05-01

    A large body of observational studies and randomized controlled trials (RCTs) has examined the role of dairy products in weight loss and maintenance of healthy weight. Yogurt is a dairy product that is generally very similar to milk, but it also has some unique properties that may enhance its possible role in weight maintenance. This review summarizes the human RCT and prospective observational evidence on the relation of yogurt consumption to the management and maintenance of body weight and composition. The RCT evidence is limited to 2 small, short-term, energy-restricted trials. They both showed greater weight losses with yogurt interventions, but the difference between the yogurt intervention and the control diet was only significant in one of these trials. There are 5 prospective observational studies that have examined the association between yogurt and weight gain. The results of these studies are equivocal. Two of these studies reported that individuals with higher yogurt consumption gained less weight over time. One of these same studies also considered changes in waist circumference (WC) and showed that higher yogurt consumption was associated with smaller increases in WC. A third study was inconclusive because of low statistical power. A fourth study observed no association between changes in yogurt intake and weight gain, but the results suggested that those with the largest increases in yogurt intake during the study also had the highest increase in WC. The final study examined weight and WC change separately by sex and baseline weight status and showed benefits for both weight and WC changes for higher yogurt consumption in overweight men, but it also found that higher yogurt consumption in normal-weight women was associated with a greater increase in weight over follow-up. Potential underlying mechanisms for the action of yogurt on weight are briefly discussed.

  12. Personal Best Time, Percent Body Fat, and Training Are Differently Associated with Race Time for Male and Female Ironman Triathletes

    Science.gov (United States)

    Knechtle, Beat; Wirth, Andrea; Baumann, Barbara; Knechtle, Patrizia; Rosemann, Thomas

    2010-01-01

    We studied male and female nonprofessional Ironman triathletes to determine whether percent body fat, training, and/or previous race experience were associated with race performance. We used simple linear regression analysis, with total race time as the dependent variable, to investigate the relationship among athletes' percent body fat, average…

  13. 26 CFR 1.46-9 - Requirements for taxpayers electing an extra one-half percent additional investment credit.

    Science.gov (United States)

    2010-04-01

    ... percent additional investment credit for property described in section 46(a)(2)(D). Paragraph (c) of this...-half percent additional investment credit. 1.46-9 Section 1.46-9 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY INCOME TAX INCOME TAXES Rules for Computing Credit for Investment in...

  14. The Use of Gas Chromatography and Mass Spectrometry to Introduce General Chemistry Students to Percent Mass and Atomic Mass Calculations

    Science.gov (United States)

    Pfennig, Brian W.; Schaefer, Amy K.

    2011-01-01

    A general chemistry laboratory experiment is described that introduces students to instrumental analysis using gas chromatography-mass spectrometry (GC-MS), while simultaneously reinforcing the concepts of mass percent and the calculation of atomic mass. Working in small groups, students use the GC to separate and quantify the percent composition…

  15. 40 CFR 63.5885 - How do I calculate percent reduction to demonstrate compliance for continuous lamination/casting...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I calculate percent reduction to... Pollutants: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5885 How do I calculate percent reduction to demonstrate compliance for continuous lamination/casting...

  16. SERIAL PERCENT-FREE PSA IN COMBINATION WITH PSA FOR POPULATION-BASED EARLY DETECTION OF PROSTATE CANCER

    Science.gov (United States)

    Ankerst, Donna Pauler; Gelfond, Jonathan; Goros, Martin; Herrera, Jesus; Strobl, Andreas; Thompson, Ian M.; Hernandez, Javier; Leach, Robin J.

    2016-01-01

    PURPOSE To characterize the diagnostic properties of serial percent-free prostate-specific antigen (PSA) in relation to PSA in a multi-ethnic, multi-racial cohort of healthy men. MATERIALS AND METHODS 6,982 percent-free PSA and PSA measures were obtained from participants in a 12 year+ Texas screening study comprising 1625 men who never underwent biopsy, 497 who underwent one or more biopsies negative for prostate cancer, and 61 diagnosed with prostate cancer. Area underneath the receiver-operating-characteristic-curve (AUC) for percent-free PSA, and the proportion of patients with fluctuating values across multiple visits were determined according to two thresholds (under 15% versus 25%) were evaluated. The proportion of cancer cases where percent-free PSA indicated a positive test before PSA > 4 ng/mL did and the number of negative biopsies that would have been spared by percent-free PSA testing negative were computed. RESULTS Percent-free PSA fluctuated around its threshold of PSA tested positive earlier than PSA in 71.4% (34.2%) of cancer cases, and among men with multiple negative biopsies and a PSA > 4 ng/mL, percent-free PSA would have tested negative in 31.6% (65.8%) instances. CONCLUSIONS Percent-free PSA should accompany PSA testing in order to potentially spare unnecessary biopsies or detect cancer earlier. When near the threshold, both tests should be repeated due to commonly observed fluctuation. PMID:26979652

  17. 40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

    Science.gov (United States)

    2010-07-01

    ... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Requirements for Commercial and Industrial Solid Waste Incineration Units That Commenced Construction On or Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or...

  18. Synthesis, structure and optical properties of two isotypic crystals, Na3MO4Cl (M=W, Mo)

    International Nuclear Information System (INIS)

    Han, Shujuan; Bai, Chunyan; Zhang, Bingbing; Yang, Zhihua; Pan, Shilie

    2016-01-01

    Two isotypic compounds, Na 3 MO 4 Cl (M = W, Mo) have been obtained from the high temperature solution, and their structures were determined by single-crystal X-ray diffraction. Both of them crystallize in the space group P4/nmm of tetragonal system with the unit cells: a=7.5181(15), c=5.360(2) for Na 3 WO 4 Cl and a=7.4942(12), c=5.3409(18) for Na 3 MoO 4 Cl. The structure exhibits a 3D network built up by the ClNa 6 groups, and the MO 4 groups reside in the tunnels of the 3D network. The structural similarities and differences between Na 3 MO 4 Cl (M=W, Mo) and Sr 3 MO 4 F (M=Al, Ga) have been discussed. Meanwhile, detailed structure comparison analyses between Na 3 MO 4 Cl (M=W, Mo) and Na 3 MO 4 F (M=W, Mo) indicate that the different connection modes of ClNa 6 and FNa 6 make Na 3 MO 4 Cl and Na 3 MO 4 F crystallize in different structures. The IR spectra were used to verify the validity of the structure. The diffuse reflectance spectra show that the UV absorption edges are about 249 nm (4.99 eV) and 265 nm (4.69 eV) for Na 3 WO 4 Cl and Na 3 MoO 4 Cl, respectively. In addition, the first-principles theoretical studies are also carried out to aid the understanding of electronic structures and linear optical properties. - Graphical abstract: Two isotypic compounds, Na 3 MO 4 Cl (M=W, Mo) have been obtained from the high temperature solution. Both of them crystallize in the space group P4/nmm of tetragonal system. The structure exhibits a 3D network built up by the ClNa 6 groups, and the MO 4 groups reside in the tunnels of the 3D network. - Highlights: • Structure and properties of Na 3 MO 4 Cl (M=W, Mo) are reported for the first time. • They show a 3D network built by ClNa 6 , and WO 4 lies in the tunnels of the network. • IR spectra were used to verify the validity of the structure. • Band structures and density of states have been calculated.

  19. Effects of Mo Content on Microstructure and Mechanical Property of PH13-8Mo Martensitic Precipitation-Hardened Stainless Steel

    Science.gov (United States)

    Yubing, Pei; Tianjian, Wang; Zhenhuan, Gao; Hua, Fan; Gongxian, Yang

    This paper introduces the effects of Mo content on microstructure and mechanical property of PH13-8Mo martensitic precipitation-hardened stainless steel which is used for LP last stage blade in steam turbine. Thermodynamic software Thermo-Calc has been used to calculate precipitation temperature and the mass fraction of precipitated phases in PH13-8Mo steel with different Mo content. The result shows that when the mass of Mo is below 0.6wt.%, chi-phase mu-phase and sigma-phase could disappear. The microstructure and mechanical property of high Mo PH13-8Mo (Mo=0.57wt.%) and low Mo PH13-8Mo (Mo=2.15wt.%)have been investigated in different heat treatments. The investigations reveal that austenitizing temperature decrease with the reduce of Mo content, so the optimum solution temperature for low Mo PH13-8Mo is lower than that for high Mo PH13-8Mo.The influence of solution temperature on grain size is weakened with the increase of Mo content, Mo rich carbides could retard coarsening of grain. An enormous amount of nano-size uniformly distributed β-NiAl particles are found in both kinds of steels using transmission electron microscopy, they are the most important strengthening phase in PH13-8Mo.

  20. Corrosion of an Fe-12 Cr-1 Mo VW steel in thermally-convective lithium

    International Nuclear Information System (INIS)

    Tortorelli, P.F.; DeVan, J.H.

    1983-01-01

    A thermal-convection loop of Fe-12 Cr-1 Mo VW steel circulated pure lithium between 500 and 350 0 C for 10,088 h. Periodic weighings of coupons at different temperatures around the loop revealed small weight losses and corrosion rates. Surface analysis showed a relatively thin corrosion layer with an underlying carbide-free zone and some depletion of chromium from the hottest specimen. While some mass transfer of chromium and nickel was detected, this mechanism did not strongly influence the weight loss process as it does with austenitic steels. Therefore, it appeared that reactions with carbon and nitrogen must be the dominant corrosion processes such that weight loss was maximized at the lowest temperature (350 0 C). Overall, the lithium-steel reactions in the temperature range of this experiment were relatively sluggish and the corrosion was not severe

  1. Structure and properties of heat-treated Ti-(40-4X)%Nb-X%Mo alloys with IE (SME)

    International Nuclear Information System (INIS)

    Silva, Marcia Almeida; Matlakhova, Lioudmila Aleksandrovna; Matlakhov, Anatoliy Nikolaevich; Paes Junior, Herval Ramos; Goncharenko, Boris Andreevich

    2010-01-01

    Whereas the inelastic effects (IE) are related with reversible martensitic transformation, in this work, was analyzed the structure and properties of heat treated Ti-(40-4x)%Nb-x%Mo alloys, where the contents of niobium and molybdenum are between 24-40%Nb and 0-4%Mo (% weight). The structural and phase analysis were done through optical microscopy and X-rays diffraction. The properties measured in this study were electrical resistivity and density. The Ti-40%Nb alloy shows a structure consisting of the β phase and αα’’ martensite with a minor participation of the α’ and ω. The alloys with 1 to 4%Mo have similar structures consisting of the β phase and traces of the α’’ phase. Thus, was observed greater capacity of Mo as a β stabilizer. The increase in Mo content in the composition of the alloys causes an increase in electrical resistivity of these. The samples may have undergone change in volume, caused by phase transformation, what possibly caused the difference between the density values calculated (theoretical) and experimental. (author)

  2. Effect of rare earth elements yttrium and lanthanum on high temperature oxidation resistance of Mo-Si-B alloys

    International Nuclear Information System (INIS)

    Majumdar, Sanjib

    2014-01-01

    In the present investigation, 0.2 to 2 at% Y and La alloyed Mo-9Si-8B were consolidated using mechanical alloying followed by spark plasma sintering. Isothermal oxidation studies were conducted in a wide temperature range from 650 to 1300℃. Detailed characterization studies of the oxide scale using SEM, EDS, FIB, TEM reveal the formation of Y x Mo 18 O 32 and 3La 2 O 3 ·MoO 3 oxide phases, respectively, for Y and La-containing alloys reduce the evaporation of MoO 3 . The growth rate of protective silica scale is also enhanced due to faster formation of Y and La rich oxide particles which probably act as nucleation sites for silica. At higher temperatures (at 1100℃), the oxidation behavior of unalloyed and RE-alloyed Mo-9Si-8B are comparable. A transient weight loss followed by a steady state is reached due to protective amorphous silica-rich scale formation beyond 1100℃. Therefore, alloying with rare earth elements provides a broader application temperature window for silicide based materials starting from 750℃ to 1300℃

  3. Mo isotope fractionation during hydrothermal evolution of porphyry Cu systems

    Science.gov (United States)

    Shafiei, Behnam; Shamanian, GholamHossein; Mathur, Ryan; Mirnejad, Hassan

    2015-03-01

    We present Mo isotope compositions of molybdenite types from three successive stages of ore deposition in several porphyry copper deposits of the Kerman region, Iran. The data provide new insights into controlling processes on Mo isotope fractionation during the hydrothermal evolution of porphyry systems. The Mo isotope compositions of 27 molybdenite samples show wide variations in δ97Mo ranging from -0.37 to +0.92 ‰. The data reveal that molybdenites in the early and transitional stages of mineralization (preferentially 2H polytypes; δ97Mo mean = 0.35 ‰) have higher δ97Mo values than late stage (mainly 3R polytypes; δ97Mo mean = 0.02 ‰) molybdenites. This trend suggests that fractionation of Mo isotopes occurred in high-temperature stages of mineralization and that hydrothermal systems generally evolve towards precipitation of molybdenite with lower δ97Mo values. Taking into account the genetic models proposed for porphyry Cu deposits along with the temperature-dependent fractionation of Mo isotope ratios, it is proposed that large variations of Mo isotopes in the early and the transitional stages of ore deposition could be controlled by the separation of the immiscible ore-forming fluid phases with different density, pH, and ƒO2 properties (i.e., brine and vapor). The fractionation of Mo isotopes during fluid boiling and Rayleigh distillation processes likely dominates the Mo isotope budget of the remaining ore-forming fluids for the late stage of mineralization. The lower δ97Mo values in the late stage of mineralization can be explained by depletion of the late ore-forming hydrothermal solutions in 97Mo, as these fluids have moved to considerable distance from the source. Finally, the relationship observed between MoS2 polytypes (2H and 3R) and their Mo isotopic compositions can be explained by the molecular vibration theory, in which heavier isotopes are preferentially partitioned into denser primary 2H MoS2 crystals.

  4. 7 CFR 201.46 - Weight of working sample.

    Science.gov (United States)

    2010-01-01

    ... specified in column 2, table 1, (2) add all these products, (3) total the percentages of all components of... the product of the weight calculated in paragraph (d)(2)(i) of this section multiplied by 100 percent... Pepper 15 150 165 Pumpkin 500 500 5 Radish 30 300 75 Rhubarb 50 300 60 Rutabaga 5 50 430 Sage 25 150 120...

  5. Development of Mo recycle technique from generator materials

    Energy Technology Data Exchange (ETDEWEB)

    Tanimoto, Masataka; Kurosawa, Makoto; Kimura, Akihiro; Nishikata, Kaori; Tsuchiya, Kunihiko [Japan Atomic Energy Agency, Oarai Research and Development Center, Oarai, Ibaraki (Japan); Kakei, Sadanori; Yoshinaga, Hideo [Taiyo Koko Corp., Ako Laboratory, Ako, Hyogo (Japan)

    2012-03-15

    The domestic {sup 99}Mo production by the (n,{gamma}) method is proposed in JMTR because of low amount of radioactive wastes and easy {sup 99}Mo/{sup 99m}Tc production process. For the development of domestic production, it is necessary to use the enriched {sup 98}MoO{sub 3}, which is very expensive, for high specific activity of {sup 99}Mo. A large amount of used PZC/PTC embraced {sup 98}Mo is also generated after the decay of {sup 99}Mo. JAEA and Taiyo Koko is proposed to recover molybdenum from the used PZC/PTC for an effective use of resources and reduction of radioactive wastes. Preliminary experiments of Mo recycling with un-irradiated MoO{sub 3} were carried out by the elution and sublimation methods. From the results, Mo recovery rate from the PZC/PTC was more than 95% by two kinds of methods. The prospects are bright for Mo recycle and reduction of radioactive wastes using these methods. (author)

  6. Nanostructured Mo-based electrode materials for electrochemical energy storage.

    Science.gov (United States)

    Hu, Xianluo; Zhang, Wei; Liu, Xiaoxiao; Mei, Yueni; Huang, Yunhui

    2015-04-21

    The development of advanced energy storage devices is at the forefront of research geared towards a sustainable future. Nanostructured materials are advantageous in offering huge surface to volume ratios, favorable transport features, and attractive physicochemical properties. They have been extensively explored in various fields of energy storage and conversion. This review is focused largely on the recent progress in nanostructured Mo-based electrode materials including molybdenum oxides (MoO(x), 2 ≤ x ≤ 3), dichalconides (MoX2, X = S, Se), and oxysalts for rechargeable lithium/sodium-ion batteries, Mg batteries, and supercapacitors. Mo-based compounds including MoO2, MoO3, MoO(3-y) (0 energy storage systems because of their unique physicochemical properties, such as conductivity, mechanical and thermal stability, and cyclability. In this review, we aim to provide a systematic summary of the synthesis, modification, and electrochemical performance of nanostructured Mo-based compounds, as well as their energy storage applications in lithium/sodium-ion batteries, Mg batteries, and pseudocapacitors. The relationship between nanoarchitectures and electrochemical performances as well as the related charge-storage mechanism is discussed. Moreover, remarks on the challenges and perspectives of Mo-containing compounds for further development in electrochemical energy storage applications are proposed. This review sheds light on the sustainable development of advanced rechargeable batteries and supercapacitors with nanostructured Mo-based electrode materials.

  7. Phase equilibria of the Mo-Al-Ho ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yitai; Chen, Xiaoxian; Liu, Hao [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Laboratory of Processing for Non-ferrous Metal and Featured Materials; Zhan, Yongzhong [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Laboratory of Processing for Non-ferrous Metal and Featured Materials; Guangxi Univ., Nanning (China). Center of Ecological Collaborative Innovation for Aluminum Industry

    2017-08-15

    Investigation into the reactions and phase equilibria of transition metal elements (i.e. Mo, Zr, Cr, V and Ti), Al and rare earths is academically and industrially important for the development of both refractory alloys and lightweight high-temperature materials. In this work, the equilibria of the Mo-Al-Ho ternary system at 773 K have been determined by using X-ray powder diffraction and scanning electron microscopy equipped with energy dispersive X-ray analysis. A new ternary phase Al{sub 4}Mo{sub 2}Ho has been found and the other ternary phase Al{sub 43}Mo{sub 4}Ho{sub 6} is observed. Ten binary phases in the Al-Mo and Al-Ho systems, including Al{sub 17}Mo{sub 4} rather than Al{sub 4}Mo, have been determined to exist at 773 K. The homogeneity ranges of AlMo{sub 3} and Al{sub 8}Mo{sub 3} phase are 7.5 at.% and 1 at.%, respectively. According to the phase-disappearing method, the maximum solubility of Al in Mo is about 16 at.%.

  8. Gold nanoparticles on MoS2 layered crystal flakes

    International Nuclear Information System (INIS)

    Cao, Wei; Pankratov, Vladimir; Huttula, Marko; Shi, Xinying; Saukko, Sami; Huang, Zhongjia; Zhang, Meng

    2015-01-01

    Inorganic layered crystal MoS 2 is considered as one of the most promising and efficient semiconductor materials for future transistors, photoelectronics, and electrocatalysis. To boost MoS 2 -based material applications, one direction is to grow physically and chemically reactive nanoparticles onto MoS 2 . Here we report on a simple route to synthesis crystalized MoS 2 –Au complexes. The gold nanoparticles were grown on MoS 2 flakes through a wet method in the oxygen free environment at room temperature. Nanoparticles with diameters varying from 9 nm to 429 nm were controlled by the molar ratios of MoS 2 and HAuCl 4 precursors. MoS 2 host flakes keep intrinsic honeycomb layered structures and the Au nanoparticles cubic-center crystal microstructures. From product chemical states analysis, the synthesis was found driven by redox reactions between the sulphide and the chloroauric acid. Photoluminescence measurement showed that introducing Au nanoparticles onto MoS 2 stacks substantially prompted excitonic transitions of stacks, as an analogy for doping Si wafers with dopants. Such composites may have potential applications in wide ranges similar as the doped Si. - Highlights: • The Au nanoparticles were decorated on MoS 2 in oxygen free ambiences via a wet method. • The Au nanoparticles are size-controllable and crystalized. • Chemical reaction scheme was clarified. • The MoS 2 –Au complexes have strong photoluminescent properties

  9. In-situ fabrication of MoSi{sub 2}/SiC–Mo{sub 2}C gradient anti-oxidation coating on Mo substrate and the crucial effect of Mo{sub 2}C barrier layer at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Jun [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Gong, Qianming, E-mail: gongqianming@mail.tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Shao, Yang; Zhuang, Daming [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Liang, Ji [Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

    2014-07-01

    MoSi{sub 2}/SiC–Mo{sub 2}C gradient coating on molybdenum was in situ prepared with pack cementation process by two steps: (1) carburizing with graphite powder to obtain a Mo{sub 2}C layer on Mo substrate, and (2) siliconizing with Si powder to get a composite MoSi{sub 2}/SiC layer on the upper part of Mo{sub 2}C layer. The microstructure and elemental distribution in the coating were investigated with scanning electron microscopy (SEM), backscattered electron (BSE), energy dispersive spectroscopy (EDS), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Cyclic oxidation tests (at 500 °C, 1200 °C, 1400 °C and 1600 °C) demonstrated excellent oxidation resistance for the gradient composite coating and the mass loss was only 0.23% in 60 min at 1600 °C. XRD, EPMA, thermal dynamic and phase diagram analyses indicated that the Mo{sub 2}C barrier layer played the key role in slowing down the diffusion of C and Si toward inner Mo substrate at high temperature and principally this contributed to the excellent anti-oxidation for Mo besides the outer MoSi{sub 2}/SiC composite layer.

  10. In-situ fabrication of MoSi2/SiC–Mo2C gradient anti-oxidation coating on Mo substrate and the crucial effect of Mo2C barrier layer at high temperature

    International Nuclear Information System (INIS)

    Liu, Jun; Gong, Qianming; Shao, Yang; Zhuang, Daming; Liang, Ji

    2014-01-01

    MoSi 2 /SiC–Mo 2 C gradient coating on molybdenum was in situ prepared with pack cementation process by two steps: (1) carburizing with graphite powder to obtain a Mo 2 C layer on Mo substrate, and (2) siliconizing with Si powder to get a composite MoSi 2 /SiC layer on the upper part of Mo 2 C layer. The microstructure and elemental distribution in the coating were investigated with scanning electron microscopy (SEM), backscattered electron (BSE), energy dispersive spectroscopy (EDS), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Cyclic oxidation tests (at 500 °C, 1200 °C, 1400 °C and 1600 °C) demonstrated excellent oxidation resistance for the gradient composite coating and the mass loss was only 0.23% in 60 min at 1600 °C. XRD, EPMA, thermal dynamic and phase diagram analyses indicated that the Mo 2 C barrier layer played the key role in slowing down the diffusion of C and Si toward inner Mo substrate at high temperature and principally this contributed to the excellent anti-oxidation for Mo besides the outer MoSi 2 /SiC composite layer.

  11. Successive 1-Month Weight Increments in Infancy Can Be Used to Screen for Faltering Linear Growth.

    Science.gov (United States)

    Onyango, Adelheid W; Borghi, Elaine; de Onis, Mercedes; Frongillo, Edward A; Victora, Cesar G; Dewey, Kathryn G; Lartey, Anna; Bhandari, Nita; Baerug, Anne; Garza, Cutberto

    2015-12-01

    Linear growth faltering in the first 2 y contributes greatly to a high stunting burden, and prevention is hampered by the limited capacity in primary health care for timely screening and intervention. This study aimed to determine an approach to predicting long-term stunting from consecutive 1-mo weight increments in the first year of life. By using the reference sample of the WHO velocity standards, the analysis explored patterns of consecutive monthly weight increments among healthy infants. Four candidate screening thresholds of successive increments that could predict stunting were considered, and one was selected for further testing. The selected threshold was applied in a cohort of Bangladeshi infants to assess its predictive value for stunting at ages 12 and 24 mo. Between birth and age 12 mo, 72.6% of infants in the WHO sample tracked within 1 SD of their weight and length. The selected screening criterion ("event") was 2 consecutive monthly increments below the 15th percentile. Bangladeshi infants were born relatively small and, on average, tracked downward from approximately age 6 to strategy is effective, the estimated preventable proportion in the group who experienced the event would be 34% at 12 mo and 24% at 24 mo. This analysis offers an approach for frontline workers to identify children at risk of stunting, allowing for timely initiation of preventive measures. It opens avenues for further investigation into evidence-informed application of the WHO growth velocity standards. © 2015 American Society for Nutrition.

  12. Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

    Energy Technology Data Exchange (ETDEWEB)

    Jana, Saumyadeep; Overman, Nicole; Varga, Tamas; Lavender, Curt; Joshi, Vineet V.

    2017-12-01

    The effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.percent Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 degrees C for 48 hours and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot- + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot- + cold-rolled to 0.2 mm + annealed at 700 deg. C for 1 hour, and (iii) hot- + cold-rolled to 0.2 mm + annealed at 1000 deg. C for 60 hours. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries.

  13. Grotrian diagrams for highly ionized molybdenum Mo VI through Mo XLII

    International Nuclear Information System (INIS)

    Shirai, Toshizo; Sugar, J.; Wiese, W.L.

    1997-07-01

    Grotrian diagrams are presented to provide graphical overviews for 1,930 spectral lines of highly ionized molybdenum, Mo VI through Mo XLII. In the usual diagram display such as that by Bashkin and Stoner (North-Holland, Amsterdam, 1975), the density of transitions is often too high to allow each transition to be drawn separately. Here in our modified diagrams, the transitions are also represented by lines connecting the upper and lower energy levels, but the lower energy levels are extended and repeated for successive configurations as needed. As a sequence, dense packing is avoided and all lines in a multiplet can be accommodated. (author)

  14. Structural transformation of MoO3 nanobelts into MoS2 nanotubes

    International Nuclear Information System (INIS)

    Deepak, Francis Leonard; Mayoral, Alvaro; Yacaman, Miguel Jose

    2009-01-01

    The structural transformation of MoO 3 nanobelts into MoS 2 nanotubes using a simple sulfur source has been reported. This transformation has been extensively investigated using electron microscopic and spectroscopic techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), electron diffraction (ED), and energy-dispersive X-ray analysis (SEM-EDAX and TEM-EDX). The method described in this report will serve as a generic route for the transformation of other oxide nanostructures into the chalcogenide nanostructures. (orig.)

  15. Weight change and physical function in older women: findings from the Nun Study.

    Science.gov (United States)

    Tully, C L; Snowdon, D A

    1995-12-01

    To investigate the association between change in weight and decline in physical function in older women. Longitudinal study of a defined population of Catholic sisters (nuns) whose weight and function were assessed twice, an average of 584 days apart. Unique life communities (convents) located throughout the United States. 475 Catholic sisters who were 75 to 99 years of age (M = 82.1, SD = 4.8) and were independent in at least one Activity of Daily Living (ADL) at the first assessment of weight and function. None. At each assessment, weight, ADLs, and cognitive function were evaluated as part of the Nun Study--a longitudinal study of aging and Alzheimer's disease. Annual percent weight change was calculated using weights from the two assessments, as well as the number of days that elapsed between assessments. Mean weight at first assessment was 140 pounds (range 78 to 232, SD = 27). The mean annual percent weight change was 0.1% (range 22% loss to 16% gain, SD = 3.8). Age- and initial weight-adjusted findings indicated that those participants with an annual percent weight loss of 3% or greater had 2.7 to 3.9 times the risk of becoming dependent in each ADL, compared to the sisters with no weight change. The elevated risk persisted in those who were mentally intact or were independent in their eating habits. Monitoring of weight may be an easy and inexpensive method of identifying older individuals at increased risk of disability.

  16. Radiochemical purity of Mo and Tc solution obtained after irradiation and dissolution of Mo-100-enriched and ultra-high-purity natural Mo disks

    Energy Technology Data Exchange (ETDEWEB)

    Tkac, Peter [Argonne National Lab. (ANL), Argonne, IL (United States); Gromov, Roman [Argonne National Lab. (ANL), Argonne, IL (United States); Chemerisov, Sergey D. [Argonne National Lab. (ANL), Argonne, IL (United States); Rotsch, David A. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-09-01

    Four irradiations of ultra-high-purity natural Mo targets and one irradiation using 97.4% Mo-100-enriched material were performed. The purpose of these irradiations was to determine whether the presence of Sn stabilizer in the H2O2 used for the dissolution of sintered Mo disks can affect the radiochemical purity of the final K2MoO4 in 5M KOH solution. Results from radiochemical purity tests performed using thin-layer paper chromatography show that even 2– 3× excess of Sn-stabilized H2O2 typically used for dissolution of sintered Mo disks did not affect the radiochemical purity of the final product.

  17. Immigrants in the one percent: The national origin of top wealth owners.

    Science.gov (United States)

    Keister, Lisa A; Aronson, Brian

    2017-01-01

    Economic inequality in the United States is extreme, but little is known about the national origin of affluent households. Households in the top one percent by total wealth own vastly disproportionate quantities of household assets and have correspondingly high levels of economic, social, and political influence. The overrepresentation of white natives (i.e., those born in the U.S.) among high-wealth households is well-documented, but changing migration dynamics suggest that a growing portion of top households may be immigrants. Because no single survey dataset contains top wealth holders and data about country of origin, this paper uses two publicly-available data sets: the Survey of Consumer Finances (SCF) and the Survey of Income and Program Participation (SIPP). Multiple imputation is used to impute country of birth from the SIPP into the SCF. Descriptive statistics are used to demonstrate reliability of the method, to estimate the prevalence of immigrants among top wealth holders, and to document patterns of asset ownership among affluent immigrants. Significant numbers of top wealth holders who are usually classified as white natives may be immigrants. Many top wealth holders appear to be European and Canadian immigrants, and increasing numbers of top wealth holders are likely from Asia and Latin America as well. Results suggest that of those in the top one percent of wealth holders, approximately 3% are European and Canadian immigrants, .5% are from Mexico or Cuban, and 1.7% are from Asia (especially Hong Kong, Taiwan, Mainland China, and India). Ownership of key assets varies considerably across affluent immigrant groups. Although the percentage of top wealth holders who are immigrants is relatively small, these percentages represent large numbers of households with considerable resources and corresponding social and political influence. Evidence that the propensity to allocate wealth to real and financial assets varies across immigrant groups suggests that

  18. Facile synthesis of stable structured MoS{sub 2}-Mo-CNFs heteroarchitecture with enhanced hydrogen evolution

    Energy Technology Data Exchange (ETDEWEB)

    Mo, Qionghua [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Faculty of Material and Energy, South West University, Chongqing 400700 (China); Yao, Yucen [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Liu, Bitao, E-mail: liubitao007@163.com [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Peng, Lingling; Yan, Hengqing; Hou, Zhupei; Wang, Jun [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Lin, Yue, E-mail: linyue@ustc.edu.cn [Hefei National Laboratory for Physical Sciences at the Microscale, University of Science and Technology of China, Anhui 230026 (China)

    2017-06-01

    3D structured MoS{sub 2} are grown in-situ on Mo particles embedded carbon nanofibers (CNFs) via a hydrothermal method. Due to this special structure, the bonding and effective electron delivery between CNFs and MoS{sub 2} are both enhanced, and which will exhibits a better hydrogen evolution activity. The onset potential of this MoS{sub 2}-Mo-CNFs catalyst will decreased to 60 mV compared to the 90 mV for the MoS{sub 2}-CNFs. And its current density nearly no change with 5000 cycles which is better than the 32.3% decrease of MoS{sub 2}-CNFs at η = 300 mV (V vs RHE). - Highlights: • Newly structured MoS{sub 2}-Mo-CNFs with effectively connection between MoS{sub 2} and CNFs successfully synthesized. • This structure can enhance the charge transfer and significantly increase electrocatalytic efficiency. • Nearly no HER activity loss after 5000 CV cycles.

  19. Predictors of weight maintenance

    NARCIS (Netherlands)

    Pasman, W.J.; Saris, W.H.M.; Westerterp-Plantenga, M.S.

    1999-01-01

    Objective: To obtain predictors of weight maintenance after a weight-loss intervention. Research Methods and Procedures: An overall analysis of data from two-long intervention studies [n = 67 women; age: 37.9±1.0 years; body weight (BW): 87.0±1.2 kg; body mass index: 32.1±0.5 kg·m-2; % body fat:

  20. Robustness of weighted networks

    Science.gov (United States)

    Bellingeri, Michele; Cassi, Davide

    2018-01-01

    Complex network response to node loss is a central question in different fields of network science because node failure can cause the fragmentation of the network, thus compromising the system functioning. Previous studies considered binary networks where the intensity (weight) of the links is not accounted for, i.e. a link is either present or absent. However, in real-world networks the weights of connections, and thus their importance for network functioning, can be widely different. Here, we analyzed the response of real-world and model networks to node loss accounting for link intensity and the weighted structure of the network. We used both classic binary node properties and network functioning measure, introduced a weighted rank for node importance (node strength), and used a measure for network functioning that accounts for the weight of the links (weighted efficiency). We find that: (i) the efficiency of the attack strategies changed using binary or weighted network functioning measures, both for real-world or model networks; (ii) in some cases, removing nodes according to weighted rank produced the highest damage when functioning was measured by the weighted efficiency; (iii) adopting weighted measure for the network damage changed the efficacy of the attack strategy with respect the binary analyses. Our results show that if the weighted structure of complex networks is not taken into account, this may produce misleading models to forecast the system response to node failure, i.e. consider binary links may not unveil the real damage induced in the system. Last, once weighted measures are introduced, in order to discover the best attack strategy, it is important to analyze the network response to node loss using nodes rank accounting the intensity of the links to the node.

  1. Photo-transmutation of {sup 100}Mo to {sup 99}Mo with Laser-Compton Scattering Gamma-ray

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jiyoung; Rehman, Haseeb ur; Kim, Yonghee [KAIST, Daejeon (Korea, Republic of)

    2016-10-15

    This paper presents a photonuclear transmutation method using laser Compton scattering (LCS) gamma-ray beam. Potential production rate (reaction rate) of 99Mo using the photonuclear (γ,n) reaction is evaluated. Rigorous optimization of the LCS spectrum has also been performed to maximize production of the 99Mo. Cyclotron proton accelerators are used worldwide to produce many short-living medical isotopes. However, few are capable of producing Mo-99 and none are suitable for producing more than a small fraction of the required amounts. More than 90% of the world's demand of 99Mo is sourced from five nuclear reactors. Two of these reactors have already been decommissioned and the rest are more than 45 years old. Relatively short half-life of the parent 99Mo requires continuous re-supply to meet the requirements of medical industry. Therefore, there is an urgent need to produce the 99Mo and 99mTc isotopes by alternative ways. One such alternative is giant dipole resonance (GDR) based photonuclear transmutation of 100Mo to 99Mo. For 99Mo production with the LCS photons using GDR-based (γ,n) reaction, the gamma-ray energy should be around 15 MeV. This study indicates that optimization of LCS spectrum by varying the electron and laser energies within practical limits can enhance the transmutation of Mo-100 to M-99 quite significantly. It has been found that irradiation time should be rather short, e.g., less than 6 hours, to maximize the weekly production of Mo-99 in the GDR-based Mo-99 production facility using the LCS photons. The analysis shows that production of 99Mo using a high-performance LCS facility offers a potentially-promising alternative for the production of 99mTc.

  2. Comparitive study of fluorescence lifetime quenching of rhodamine 6G by MoS2 and Au-MoS2

    Science.gov (United States)

    Shakya, Jyoti; Kasana, Parath; Mohanty, T.

    2018-04-01

    Time resolved fluorescence study of Rhodamine 6G (R6G) in the presence of Molybdenum disulfide (MoS2) nanosheets and gold doped MoS2 (Au-MoS2) have been carried out and discussed. We have analyzed the fluorescence decay curves of R6G and it is observed that Au-MoS2 is a better fluorescence lifetime quencher as compare to MoS2 nanosheets. Also, the energy transfer efficiency and energy transfer rate from R6G to MoS2 and Au-MoS2 has been calculated and found higher for Au-MoS2.

  3. Na2MoO2As2O7

    Directory of Open Access Journals (Sweden)

    Raja Jouini

    2012-12-01

    Full Text Available Disodium molybdenum dioxide diarsenate, Na2MoO2As2O7, has been synthesized by a solid-state reaction. The structure is built up from MoAs2O12 linear units sharing corners to form a three-dimensional framework containing tunnels running along the a-axis direction in which the Na+ cations are located. In this framework, the AsV atoms are tetrahedrally coordinated and form an As2O7 group. The MoVI atom is displaced from the center of an octahedron of O atoms. Two Na+ cations are disordered about inversion centres. Structural relationships between different compounds: A2MoO2As2O7 (A = K, Rb, AMOP2O7 (A = Na, K, Rb; M = Mo, Nb and MoP2O7 are discussed.

  4. Atomic scale onset of Al adhesion on Mo2BC

    International Nuclear Information System (INIS)

    Bolvardi, Hamid; Music, Denis; Schneider, Jochen M.

    2015-01-01

    We have explored interfacial interactions between a Mo–C terminated Mo 2 BC(040) surface and an Al cluster using ab initio molecular dynamics. The Al cluster is disrupted and wets the Mo 2 BC(040) surface. This can be understood based on the electronic structure. Across the Al–MoC interface C s–Al s hybridized states are formed. These bonds are stronger than the Al–Al intra-cluster bonds. Hence, the onset of Al adhesion is caused by bond formation across the Al–MoC interface. - Highlights: • Interfacial interactions between Mo 2 BC and an Al cluster were explored. • Al forms bonds to C constituting the onset of Al adhesion on Mo 2 BC. • These data are relevant for other carbide coatings

  5. U-Mo fuel qualification program in HANARO

    International Nuclear Information System (INIS)

    Lee, K.H.; Lee, C.S.; Kim, H.R.; Kuk, I.H.; Kim, C.K.

    2000-01-01

    Atomized U-Mo fuel has shown good performance from the results of previous out-of-pile tests and post-irradiation examinations. A qualification program of rod type U-Mo fuel is in progress and the fuel will be irradiated in HANARO. 6 gU/cm 3 U-7Mo, U-8Mo and U-9Mo are considered in this program. The laboratory test results of porosity, mechanical property, thermal conductivity, and thermal compatibility test are discussed in this paper. In parallel with this qualification program, the feasibility study on the core conversion from the present U 3 Si fuel to U-Mo in HANARO will be initiated to provide technical bases for the policy making. Several options of core conversion for HANARO are proposed and each option will be addressed briefly in terms of the operation policy, fuel management, and licensing of HANARO. (author)

  6. Does Successful Weight Loss in an Internet-Based Worksite Weight Loss Program Improve Employee Presenteeism and Absenteeism?

    Science.gov (United States)

    Harden, Samantha M.; You, Wen; Almeida, Fabio A.; Hill, Jennie L.; Linnan, Laura A.; Allen, Kacie C.; Estabrooks, Paul A.

    2017-01-01

    Certain risk factors associated with overweight and obesity may lead to reduced productivity in the workforce (i.e., increased absenteeism and presenteeism). Participants in a large, Internet-based worksite weight loss intervention, who were present at follow-up (N = 1,030), completed a self-reported productivity measure (World Health Organization’s Health and Work Performance Questionnaire) at baseline and postintervention. Twenty-two percent of the participants lost a clinically meaningful amount of weight (≥5% weight loss). There were no statistically significant (p absenteeism or for absolute or relative presenteeism. Within a modestly successful Internet-based, worksite weight loss intervention, weight loss did not improve self-reported absenteeism or presenteeism. Further studies are needed to explore the sensitivity of the World Health Organization’s Health and Work Performance Questionnaire and the long-term effects of weight loss on productivity. PMID:25842385

  7. Does Successful Weight Loss in an Internet-Based Worksite Weight Loss Program Improve Employee Presenteeism and Absenteeism?

    Science.gov (United States)

    Harden, Samantha M; You, Wen; Almeida, Fabio A; Hill, Jennie L; Linnan, Laura A; Allen, Kacie C; Estabrooks, Paul A

    2015-12-01

    Certain risk factors associated with overweight and obesity may lead to reduced productivity in the workforce (i.e., increased absenteeism and presenteeism). Participants in a large, Internet-based worksite weight loss intervention, who were present at follow-up (N = 1,030), completed a self-reported productivity measure (World Health Organization's Health and Work Performance Questionnaire) at baseline and postintervention. Twenty-two percent of the participants lost a clinically meaningful amount of weight (≥5% weight loss). There were no statistically significant (p absenteeism or for absolute or relative presenteeism. Within a modestly successful Internet-based, worksite weight loss intervention, weight loss did not improve self-reported absenteeism or presenteeism. Further studies are needed to explore the sensitivity of the World Health Organization's Health and Work Performance Questionnaire and the long-term effects of weight loss on productivity. © 2015 Society for Public Health Education.

  8. Role of percent tissue altered on ectasia after LASIK in eyes with suspicious topography.

    Science.gov (United States)

    Santhiago, Marcony R; Smadja, David; Wilson, Steven E; Krueger, Ronald R; Monteiro, Mario L R; Randleman, J Bradley

    2015-04-01

    To investigate the association of the percent tissue altered (PTA) with the occurrence of ectasia after LASIK in eyes with suspicious preoperative corneal topography. This retrospective comparative case-control study compared associations of reported ectasia risk factors in 129 eyes, including 57 eyes with suspicious preoperative Placido-based corneal topography that developed ectasia after LASIK (suspect ectasia group), 32 eyes with suspicious topography that remained stable for at least 3 years after LASIK (suspect control group), and 30 eyes that developed ectasia with bilateral normal topography (normal topography ectasia group). Groups were subdivided based on topographic asymmetry into high- or low-suspect groups. The PTA, preoperative central corneal thickness (CCT), residual stromal bed (RSB), and age (years) were evaluated in univariate and multivariate analyses. Average PTA values for normal topography ectasia (45), low-suspect ectasia (39), high-suspect ectasia (36), low-suspect control (32), and high-suspect control (29) were significantly different from one another in all comparisons (P topography ectasia groups, and CCT was not significantly different between any groups. Stepwise logistic regression revealed the PTA as the most significant independent variable (P topography. Less tissue alteration, or a lower PTA value, was necessary to induce ectasia in eyes with more remarkable signs of topographic abnormality, and PTA provided better discriminative capabilities than RSB for all study populations. Copyright 2015, SLACK Incorporated.

  9. Percent body fat is a better predictor of cardiovascular risk factors than body mass index

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Qiang; Dong, Sheng-Yong; Sun, Xiao-Nan; Xie, Jing; Cui, Yi [International Medical Center, Chinese PLA General Hospital, Beijing (China)

    2012-04-20

    The objective of the present study was to evaluate the predictive values of percent body fat (PBF) and body mass index (BMI) for cardiovascular risk factors, especially when PBF and BMI are conflicting. BMI was calculated by the standard formula and PBF was determined by bioelectrical impedance analysis. A total of 3859 ambulatory adult Han Chinese subjects (2173 males and 1686 females, age range: 18-85 years) without a history of cardiovascular diseases were recruited from February to September 2009. Based on BMI and PBF, they were classified into group 1 (normal BMI and PBF, N = 1961), group 2 (normal BMI, but abnormal PBF, N = 381), group 3 (abnormal BMI, but normal PBF, N = 681), and group 4 (abnormal BMI and PBF, N = 836). When age, gender, lifestyle, and family history of obesity were adjusted, PBF, but not BMI, was correlated with blood glucose and lipid levels. The odds ratio (OR) and 95% confidence interval (CI) for cardiovascular risk factors in groups 2 and 4 were 1.88 (1.45-2.45) and 2.06 (1.26-3.35) times those in group 1, respectively, but remained unchanged in group 3 (OR = 1.32, 95%CI = 0.92-1.89). Logistic regression models also demonstrated that PBF, rather than BMI, was independently associated with cardiovascular risk factors. In conclusion, PBF, and not BMI, is independently associated with cardiovascular risk factors, indicating that PBF is a better predictor.

  10. Detection of viability by percent thallium uptake with conventional thallium scintigraphy

    International Nuclear Information System (INIS)

    Imai, Kamon; Araki, Yasushi; Horiuchi, Kou-ichi; Yumikura, Sei; Saito, Satoshi; Ozawa, Yukio; Kan-matsuse, Katsuo; Hagiwara, Kazuo.

    1994-01-01

    Thallium myocardial scintigraphy (TMS) is used for diagnosis of viability in infarcted myocardium before coronary revascularization. Underestimation of viability by TMS has been reported by many investigators. To evaluate viability precisely, thallium re-injection method or 24 hour delayed imaging is performed. However, these techniques are not convenient and are difficult to perform in clinical practice. Percent T1-uptake method was developed for predicting myocardial viability. To evaluate usefulness of this method, TMS was performed before and after PTCA in 23 patients with myocardial infarction. Left ventricle was divided into 3 layers, then each layer was divided into 4 segments (12 segments in total). Forth three segments showed recovery of perfusion on TMS after PTCA. Viability in infarcted myocardium is predicted by 1) redistribution (RD), 2) %T1-uptake≥45% on the image immediately after exercise (TE), and 3) %T1-uptake≥45% on delayed image (TD). Sensitivity was RD: 60%, TE: 90% and TD: 95% (p<0.001 vs. RD). Specificity was RD: 74%, TE: 68%, and TD: 60% (NS). Predictive accuracy (PA) was RD: 69%, TE: 77%, TD: 73% (NS). Compared with RD, %T1-uptake, either TE or TD, increased sensitivity with slightly improved PA, but decreased specificity slightly. Therefore %T1-uptake would be a sensitive and useful predictor to find patients who are most likely to benefit from re-vascularization. (author)

  11. EPIC Studies: Governments Finance, On Average, More Than 50 Percent Of Immunization Expenses, 2010-11.

    Science.gov (United States)

    Brenzel, Logan; Schütte, Carl; Goguadze, Keti; Valdez, Werner; Le Gargasson, Jean-Bernard; Guthrie, Teresa

    2016-02-01

    Governments in resource-poor settings have traditionally relied on external donor support for immunization. Under the Global Vaccine Action Plan, adopted in 2014, countries have committed to mobilizing additional domestic resources for immunization. Data gaps make it difficult to map how well countries have done in spending government resources on immunization to demonstrate greater ownership of programs. This article presents findings of an innovative approach for financial mapping of routine immunization applied in Benin, Ghana, Honduras, Moldova, Uganda, and Zambia. This approach uses modified System of Health Accounts coding to evaluate data collected from national and subnational levels and from donor agencies. We found that government sources accounted for 27-95 percent of routine immunization financing in 2011, with countries that have higher gross national product per capita better able to finance requirements. Most financing is channeled through government agencies and used at the primary care level. Sustainable immunization programs will depend upon whether governments have the fiscal space to allocate additional resources. Ongoing robust analysis of routine immunization should be instituted within the context of total health expenditure tracking. Project HOPE—The People-to-People Health Foundation, Inc.

  12. Percent body fat is a better predictor of cardiovascular risk factors than body mass index

    International Nuclear Information System (INIS)

    Zeng, Qiang; Dong, Sheng-Yong; Sun, Xiao-Nan; Xie, Jing; Cui, Yi

    2012-01-01

    The objective of the present study was to evaluate the predictive values of percent body fat (PBF) and body mass index (BMI) for cardiovascular risk factors, especially when PBF and BMI are conflicting. BMI was calculated by the standard formula and PBF was determined by bioelectrical impedance analysis. A total of 3859 ambulatory adult Han Chinese subjects (2173 males and 1686 females, age range: 18-85 years) without a history of cardiovascular diseases were recruited from February to September 2009. Based on BMI and PBF, they were classified into group 1 (normal BMI and PBF, N = 1961), group 2 (normal BMI, but abnormal PBF, N = 381), group 3 (abnormal BMI, but normal PBF, N = 681), and group 4 (abnormal BMI and PBF, N = 836). When age, gender, lifestyle, and family history of obesity were adjusted, PBF, but not BMI, was correlated with blood glucose and lipid levels. The odds ratio (OR) and 95% confidence interval (CI) for cardiovascular risk factors in groups 2 and 4 were 1.88 (1.45-2.45) and 2.06 (1.26-3.35) times those in group 1, respectively, but remained unchanged in group 3 (OR = 1.32, 95%CI = 0.92-1.89). Logistic regression models also demonstrated that PBF, rather than BMI, was independently associated with cardiovascular risk factors. In conclusion, PBF, and not BMI, is independently associated with cardiovascular risk factors, indicating that PBF is a better predictor

  13. The BDGP gene disruption project: Single transposon insertions associated with 40 percent of Drosophila genes

    Energy Technology Data Exchange (ETDEWEB)

    Bellen, Hugo J.; Levis, Robert W.; Liao, Guochun; He, Yuchun; Carlson, Joseph W.; Tsang, Garson; Evans-Holm, Martha; Hiesinger, P. Robin; Schulze, Karen L.; Rubin, Gerald M.; Hoskins, Roger A.; Spradling, Allan C.

    2004-01-13

    The Berkeley Drosophila Genome Project (BDGP) strives to disrupt each Drosophila gene by the insertion of a single transposable element. As part of this effort, transposons in more than 30,000 fly strains were localized and analyzed relative to predicted Drosophila gene structures. Approximately 6,300 lines that maximize genomic coverage were selected to be sent to the Bloomington Stock Center for public distribution, bringing the size of the BDGP gene disruption collection to 7,140 lines. It now includes individual lines predicted to disrupt 5,362 of the 13,666 currently annotated Drosophila genes (39 percent). Other lines contain an insertion at least 2 kb from others in the collection and likely mutate additional incompletely annotated or uncharacterized genes and chromosomal regulatory elements. The remaining strains contain insertions likely to disrupt alternative gene promoters or to allow gene mis-expression. The expanded BDGP gene disruption collection provides a public resource that will facilitate the application of Drosophila genetics to diverse biological problems. Finally, the project reveals new insight into how transposons interact with a eukaryotic genome and helps define optimal strategies for using insertional mutagenesis as a genomic tool.

  14. MoRM and Future Memories

    DEFF Research Database (Denmark)

    Rehder, Mads Middelboe; Ostrowski, Kasper

    2017-01-01

    for the experimental workshop we lunged into a process of devising both an interactive exhibition and an installation which explored the ‘big data’ citizens regularly produce in their everyday lives and how this data might be archived, packaged, and recycled - or even forgotten, primarily within social media. We...... wanted to explore what our daily routines connected to social media and sorting our data meant for the way we shape our memories, and therefore the traces of future memories. In this chapter we follow the trajectory of the exhibition entitled ‘MoRM’ (Museum of Random Memories)....

  15. Phase formation in the Li2MoO4–K2MoO4–In2(MoO4)3 system and crystal structures of new compounds K3InMo4O15 and LiK2In(MoO4)3

    International Nuclear Information System (INIS)

    Khal’baeva, Klara M.; Solodovnikov, Sergey F.; Khaikina, Elena G.; Kadyrova, Yuliya M.; Solodovnikova, Zoya A.; Basovich, Olga M.

    2012-01-01

    XRD study of solid-phase interaction in the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system was performed. The boundary K 2 MoO 4 –In 2 (MoO 4 ) 3 system is an non-quasibinary join of the K 2 O–In 2 O 3 –MoO 3 system where a new polymolybdate K 3 InMo 4 O 15 isotypic to K 3 FeMo 4 O 15 was found. In the structure (a=33.2905(8), b=5.8610(1), c=15.8967(4) Å, β=90.725(1)°, sp. gr. C2/c, Z=8, R(F)=0.0407), InO 6 octahedra, Mo 2 O 7 diortho groups and MoO 4 tetrahedra form infinite ribbons {[In(MoO 4 ) 2 (Mo 2 O 7 )] 3− } ∞ along the b-axis. Between the chains, 8- to 10-coordinate potassium cations are located. A subsolidus phase diagram of the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system was constructed and a novel triple molybdate LiK 2 In(MoO 4 ) 3 was revealed. Its crystal structure (a=7.0087(2), b=9.2269(3), c=10.1289(3) Å, β=107.401(1)°, sp. gr. P2 1 , Z=2, R(F)=0.0280) contains an open framework of vertex-shared MoO 4 tetrahedra, InO 6 octahedra and LiO 5 tetragonal pyramids with nine- and seven-coordinate potassium ions in the framework channels. - Graphical abstract: Exploring the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system showed its partial non-quasibinarity and revealed new compounds K 3 InMo 4 O 15 (isotypic to K 3 FeMo 4 O 15 ) and LiK 2 In(MoO 4 ) 3 which were structurally studied. An open framework of the latter is formed by vertex-shared MoO 4 tetrahedra, InO 6 octahedra and LiO 5 tetragonal pyramids. Highlights: ► Subsolidus phase relations in the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system were explored. ► The K 2 MoO 4 –In 2 (MoO 4 ) 3 system is a non-quasibinary join of the K 2 O–In 2 O 3 –MoO 3 system. ► New compounds K 3 InMo 4 O 15 and LiK 2 In(MoO 4 ) 3 were obtained and structurally studied. ► K 3 InMo 4 O 15 is isotypic to K 3 FeMo 4 O 15 and carries bands of InO 6 , MoO 4 and Mo 2 O 7 units. ► An open framework of LiK 2 In(MoO 4 ) 3 is formed by polyhedra MoO 4 , InO 6 and LiO 5 .

  16. Ordering in rapidly solidified Ni/sub 2/Mo

    International Nuclear Information System (INIS)

    Kulkarni, U.D.; Dey, G.K.; Banerjee, S.

    1988-01-01

    Ordering processes in the Ni-Mo system have been a subject of several investigations. Although the ordering behaviour of the Ni/sub 4/Mo and the Ni/sub 3/Mo has been examined in detail, no such study has been reported in the case of the Ni/sub 2/Mo alloy. The lack of experimental work on ordering transformations in Ni/sub 2/Mo is presumably due to the difficulty in obtaining a single phase fcc alloy of this composition. Enhanced solid solubility of Mo in Ni, which accompanies rapid solidification processing (RSP) makes the formation of such a phase possible. The ordering processes in Ni-Mo based alloys show several remarkable features. Firstly, the alloy (15 - 28 at % Mo) quenched from the α -phase filed exhibit a short range order (SRO) characterized by the presence of intensity maxima at /1 1/2 0/ fcc positions of the reciprocal space. This state of SRO has been attributed to the occurrence of 1 1/2 O spinodal ordering in the system. Secondly, the transformation from the state of SRO to the equilibrium/metastable coherent long range ordered (LRO) structures appears to take place in a continuous manner at relatively low temperatures of aging. Three different coherent LRO structures, namely: the equilibrium Ni/sub 4/Mo (prototype structure D1/sub a/) and the metastable Ni/sub 3/Mo (DO/sub 22/) and Ni/sub 2/Mo (Pt/sub 2/Mo) structures have reported to evolve from the SRO alloy, depending upon the aging treatment and the composition of the alloy

  17. Computational identification of MoRFs in protein sequences.

    Science.gov (United States)

    Malhis, Nawar; Gsponer, Jörg

    2015-06-01

    Intrinsically disordered regions of proteins play an essential role in the regulation of various biological processes. Key to their regulatory function is the binding of molecular recognition features (MoRFs) to globular protein domains in a process known as a disorder-to-order transition. Predicting the location of MoRFs in protein sequences with high accuracy remains an important computational challenge. In this study, we introduce MoRFCHiBi, a new computational approach for fast and accurate prediction of MoRFs in protein sequences. MoRFCHiBi combines the outcomes of two support vector machine (SVM) models that take advantage of two different kernels with high noise tolerance. The first, SVMS, is designed to extract maximal information from the general contrast in amino acid compositions between MoRFs, their surrounding regions (Flanks), and the remainders of the sequences. The second, SVMT, is used to identify similarities between regions in a query sequence and MoRFs of the training set. We evaluated the performance of our predictor by comparing its results with those of two currently available MoRF predictors, MoRFpred and ANCHOR. Using three test sets that have previously been collected and used to evaluate MoRFpred and ANCHOR, we demonstrate that MoRFCHiBi outperforms the other predictors with respect to different evaluation metrics. In addition, MoRFCHiBi is downloadable and fast, which makes it useful as a component in other computational prediction tools. http://www.chibi.ubc.ca/morf/. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  18. Atomic structure calculations of Mo XV-XL

    International Nuclear Information System (INIS)

    Kubo, Hirotaka; Sugie, Tatsuo; Shiho, Makoto; Suzuki, Yasuo; Ishii, Keishi; Maeda, Hikosuke.

    1986-06-01

    Energy levels and oscillator strengths were calculated for Mo XV - Mo XL. The computer program for atomic structure calculation, developed by Dr. Robert D. Cowan, Los Alamos National Laboratory, was used in the present work. The scaled energy parameters were empirically determined from the observed spectral data. We present wavelengths and transition probabilities of Mo XV-XL. Energy levels and spectral patterns are presented in figures that are useful for the identification of spectral lines. (author)

  19. Solvothermal conversion of technical lignins over NiMo catalysts

    DEFF Research Database (Denmark)

    Ghafarnejad Parto, Soheila; Christensen, Jakob Munkholt; Pedersen, Lars Saaby

    Scope: Lignin, cellulose and hemicellulose are the main constituents of plants cell walls. Lignin is an aromatic rich compound, composed of phenolic building blocks. Depending on the method used for isolation of lignin from cellulose and hemicellulose, several types of technical lignin are availa......Scope: Lignin, cellulose and hemicellulose are the main constituents of plants cell walls. Lignin is an aromatic rich compound, composed of phenolic building blocks. Depending on the method used for isolation of lignin from cellulose and hemicellulose, several types of technical lignin...... of the range of available technical lignins. In this work, catalytic conversion of different types of lignin using an alumina supported NiMo catalyst (provided by Haldor Topsøe A/S) is conducted in ethanol at 310 ˚C with initial hydrogen pressure of 25 barg. The reaction time was set to 3 hours. Proton......, attributed as ‘bio-oil’. GC-MS-FID analysis was used for identification and quantification of the bio-oil and ethanol rich light fraction. The molecular weight of the oil fraction was determined by size exclusion chromatography (SEC). Elemental analysis (Eurovector EuroEA3000) was conducted for measuring...

  20. Intermediate report of MoReMo. Modelling resilience for maintenance and outage

    Energy Technology Data Exchange (ETDEWEB)

    Oedewald, P.; Macchi, L. (VTT Technical Research Centre of Finland (Finland)); Axelsson, C. (Ringhals AB, Vattenfall AB (Sweden)); Eitrheim, M.H.R. (Institute for Energy Technology (Norway))

    2012-02-15

    Resilience Engineering (RE) is a new approach to safety that helps organisations and individuals adapt to unforeseen events and long-term changes. Such an approach is needed by nuclear power plants (NPPs) as they face demanding modification projects, high staff turnover and increased pressures to maintain and improve safety. The goal of the Modelling Resilience for Maintenance and Outage (MoReMO) project is to develop and test models and methods to identify and analyse resilience in safety-critical activities in natural everyday settings. In 2011, we have applied four approaches in different case studies: Organisational Core Task modelling (OCT), Functional Resonance Analysis Method (FRAM), Efficiency Thoroughness Trade-Off (ETTO) analysis, and Work Practice and Culture Characterisation. The project has collected data through observations, interviews and document reviews at two NPPs. Together, the four approaches have provided valuable insights for understanding the rationale behind work practices, their effects on safety, and the support of flexibility and adaptability. In 2012, the MoReMO project will complete the data collection and integrate results on how resilience can be operationalized in practical safety management tools for the companies. (Author)

  1. Sheet-like of Mo –Sm assembly containing [Mo (CN)8 ] and Sm ions ...

    Indian Academy of Sciences (India)

    Administrator

    421–427. © Indian Academy of Sciences. 421 ... Department of Chemistry, Nankai University, Tianjin, 300071, PR China e-mail: ... [Mo(CN)8]3– building blocks, this paper details the ..... 20601014), and National Basic Research Program of.

  2. IEA Mobility Model (MoMo) and its use in the ETP 2008

    International Nuclear Information System (INIS)

    Fulton, Lew; Cazzola, Pierpaolo; Cuenot, Francois

    2009-01-01

    The IEA published 'Energy Technology Perspectives' (ETP) in June 2008. That document reports on IEA scenarios for baseline and low-CO 2 alternative scenarios to 2050, across the energy economy. The study included creating scenarios for transport, using the IEA Mobility Model (MoMo). This paper reports on the transport-related ETP scenarios and describes the model used in the analysis. According to the ETP Baseline scenario, world transport energy use and CO 2 emissions will more than double by 2050. In the most challenging scenario, called 'BLUE', transport emissions are reduced by 70% in 2050 compared to their baseline level in that year (and about 25% below their 2005 levels). There are several versions of the BLUE scenario, but all involve: a 50% or greater improvement in LDV efficiency, 30-50% improvement in efficiency of other modes (e.g. trucks, ships and aircraft), 25% substitution of liquid fossil fuels by biofuels, and considerable penetration of electric and/or fuel-cell vehicles. In the second half of this paper, an overview of the MoMo model is provided. Details on the complete analysis are contained in the ETP 2008 document, available at (www.iea.org). Details of the LDV fuel economy analysis are contained in a separate paper in this collection.

  3. Intermediate report of MoReMo. Modelling resilience for maintenance and outage

    International Nuclear Information System (INIS)

    Oedewald, P.; Macchi, L.; Axelsson, C.; Eitrheim, M.H.R.

    2012-02-01

    Resilience Engineering (RE) is a new approach to safety that helps organisations and individuals adapt to unforeseen events and long-term changes. Such an approach is needed by nuclear power plants (NPPs) as they face demanding modification projects, high staff turnover and increased pressures to maintain and improve safety. The goal of the Modelling Resilience for Maintenance and Outage (MoReMO) project is to develop and test models and methods to identify and analyse resilience in safety-critical activities in natural everyday settings. In 2011, we have applied four approaches in different case studies: Organisational Core Task modelling (OCT), Functional Resonance Analysis Method (FRAM), Efficiency Thoroughness Trade-Off (ETTO) analysis, and Work Practice and Culture Characterisation. The project has collected data through observations, interviews and document reviews at two NPPs. Together, the four approaches have provided valuable insights for understanding the rationale behind work practices, their effects on safety, and the support of flexibility and adaptability. In 2012, the MoReMO project will complete the data collection and integrate results on how resilience can be operationalized in practical safety management tools for the companies. (Author)

  4. Trends in Weight Regain Following Roux-en-Y Gastric Bypass (RYGB) Bariatric Surgery.

    Science.gov (United States)

    Cooper, Timothy C; Simmons, Elizabeth B; Webb, Kirsten; Burns, James L; Kushner, Robert F

    2015-08-01

    The primary purpose of this study was to assess weight loss and occurrence of weight regain among patients who underwent Roux-en-Y gastric bypass (RYGB) using categorical analysis. Study participants were selected from patients who underwent RYGB from a single institution. Participants (n = 300, mean procedure age = 45.6 ± 9.9) completed surveys for self-reported preoperative weight, current weight, and subsequent weights over postoperative years. Measured weights and confirmed procedure dates were acquired from patient medical records. Mean preoperative weight and BMI were 140.8 kg ± 32.1 and 49.7 ± 9.9, respectively, and mean years since surgery was 6.9 ± 4.9. Study subjects were mostly Caucasian (56.7 %) and female (80.3 %). Participants were stratified a priori into four cohorts based on percent of weight loss at 1 year, 35 % (n = 113). General linear model analyses were conducted to assess the effect of year one weight loss on percent weight regain. The mean weight regain for all patients was 23.4 % of maximum weight loss. Using categorical analysis, mean weight regain in the 35 % weight loss cohorts was 29.1, 21.9, 20.9, and 23.8 %, respectively. Excessive weight regain, defined as ≥25 % of total lost weight, occurred in 37 % of patients. Weight gain is a common complication following RYGB surgery. Despite the percentage of weight loss over the first year, all cohort patient groups regained on average between 21 and 29 % of lost weight. Excessive weight gain was experienced by over one third of patients. Greater initial absolute weight loss leads to more successful long-term weight outcomes.

  5. Conceptual study of 99Mo production in JRR-3

    International Nuclear Information System (INIS)

    Hirose, Akira; Komeda, Masao; Kinase, Masami; Sorita, Takami; Wada, Shigeru

    2010-06-01

    We investigated the production process of 99 Mo, which is parent nuclide of 99m Tc, in JRR-3. 99m Tc is most commonly used as a radiopharmaceutical in the field of nuclear medicine. Currently the supplying of 99 Mo is only dependent on imports from foreign countries, so JAEA is aiming at domestic production of a part of 99 Mo in cooperation with the industrial arena. This report presents the technical study for the production process of 99 Mo by using the neutron radiation method of (n, γ) reaction in JRR-3. (author)

  6. Development of Commercial-scale Fission Mo-99 Production System

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seung-Kon; Lee, Suseung; Hong, Soon-Bog; Jang, Kyung-Duk; Park, Ul Jael; Lee, Jun Sig [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    These days, worldwide {sup 99} Mo supply is not only insufficient but also unstable. Because, most of the main {sup 99}Mo production reactors are more than years old and suffered from frequent and unscheduled shutdown. Therefore, movement to replace old reactors to keep stable supply is now active. Under these conditions, KAERI (Korea Atomic Energy Research Institute) is developing LEU-based fission {sup 99}Mo production process which is connected to the new research reactor (Kijang New Research Reactor, KJRR), which is being constructed in Gijang, Busan, Korea. Historically, the most fission {sup 99}Mo producers have been used highly enriched uranium (HEU) targets so far. However, to reduce the use of HEU in private sector for non-proliferation, {sup 99}Mo producers are forced to convert their HEU-based process to use low enriched uranium (LEU) targets. Economic impact of a target conversion from HEU to LEU is significant. In this study, fission {sup 99}Mo process with non-irradiated LEU targets was presented except separation and purification steps. Pre- and post-irradiation tests of the fission {sup 99}Mo target will be done in 4th quarter of 2016. For the fission Mo production process development, hot experiments with irradiated LEU targets will be done in 4th quarter of 2016. Then, verification of the production process with quality control will be followed until the commercial production of fission {sup 99}Mo scheduled in 2019.

  7. Faceted MoS2 nanotubes and nanoflowers

    International Nuclear Information System (INIS)

    Deepak, Francis Leonard; Mayoral, Alvaro; Yacaman, Miguel Jose

    2009-01-01

    A simple synthesis of novel faceted MoS 2 nanotubes (NTs) and nanoflowers (NFs) starting from molybdenum oxide and thiourea as the sulphur source is reported. The MoS 2 nanotubes with the faceted morphology have not been observed before. Further the as-synthesized MoS 2 nanotubes have high internal surface area. The nanostructures have been characterized by a variety of electron microscopy techniques. It is expected that these MoS 2 nanostrutures will find important applications in energy storage, catalysis and field emission.

  8. Synthesis of nanometre-thick MoO3 sheets

    Science.gov (United States)

    Kalantar-Zadeh, Kourosh; Tang, Jianshi; Wang, Minsheng; Wang, Kang L.; Shailos, Alexandros; Galatsis, Kosmas; Kojima, Robert; Strong, Veronica; Lech, Andrew; Wlodarski, Wojtek; Kaner, Richard B.

    2010-03-01

    The formation of MoO3 sheets of nanoscale thickness is described. They are made from several fundamental sheets of orthorhombic α-MoO3, which can be processed in large quantities via a low cost synthesis route that combines thermal evaporation and mechanical exfoliation. These fundamental sheets consist of double-layers of linked distorted MoO6 octahedra. Atomic force microscopy (AFM) measurements show that the minimum resolvable thickness of these sheets is 1.4 nm which is equivalent to the thickness of two double-layers within one unit cell of the α-MoO3 crystal.

  9. MoMoSat -- Mobile Service for Monitoring with GeoNotes via Satellite

    Energy Technology Data Exchange (ETDEWEB)

    Niemeyer, Irmgard [Forschungszentrum Juelich (Germany). Programme Group Systems Analysis and Technology Evaluation (STE); Jonas, Karl [Univ. of Applied Science Bonn-Rhein-Sieg, Sankt Augustin (Germany). FhG FOKUS CC SATCom; Horz, Alexander [horz informatik, Sankt Augustin (Germany); Wettschereck, Dietrich; Schmidt, Dirk [DIALOGIS GmbH, Bonn (Germany)

    2003-05-01

    The MoMoSat service will enable mobile end-users to view, manage, annotate, and communicate mapbased information in the field. The handled information exists of a huge volume of raster (satellite or aerial images) and vector data (i.e. street networks, cadastral maps or points of interest), as well as text-specific geo-referenced textual notes (the so-called 'GeoNotes') and real-time voice. A secure real-time communication between mobile units and the primary data store is an essential task of the MoMoSat service. The basic information is stored in the primary database that is accessible through a virtual private network (VPN) and cached at a server at a base station in order to ensure data availability. The base station may be installed in a car or another mobile vehicle. The two servers will periodically communicate with each other via secure satellite communication in order to check for updates. The base station supplies the relevant GIS data for the mobile units (people or even robots in the field at remote solutions). The communication between the mobile units is based on a peer-to-peer wireless local area network (WLAN) architecture. The mobile units are equipped with mobile computers (i.e. laptop, tablet PC or PDA) combined with a satellite-based positioning system (GPS) that enables them to request the proper geographic data sets from yhe base station's map server. An interactive mapping software shows the actual location on the map and allows the user to navigate (zoom, pan) through the high-resolution map display. The user can switch 'on' or 'off' several thematic layers (i.e. street network or points of interest) on the map. The software also supports collaborative aspects of MoMoSat by offering tools for the management of the GeoNotes that can be visualized by categories. The user can extend the existing GeoNotes with his personnel comments or create new GeoNotes by defining categories, recipients and the level of

  10. Comparative study of NiW, NiMo and MoW prepared by mechanical alloying

    International Nuclear Information System (INIS)

    Gonzalez, G.; Sagarzazu, A.; Villalba, R.; Ochoa, J.

    2007-01-01

    The present work concern the amorphisation process induced by mechanical alloying in the NiW, NiMo and MoW systems. The alloys chosen combine a group of transition elements varying from very similar atomic radius and electronic valences (MoW) to different ones (NiW and NiMo). The three systems achieved an amorphous state after 50 h of milling. The mechanism of amorphisation proposed for NiW and NiMo was the combined effect of an excess concentration of the solute atoms entering into the structure of one of the elements and a critical concentration of defects. Continuous formation of an amorphous phase at the interface of the crystalline phase was observed during the process. MoW seems to amorphize by continuous reduction of grain size down to a critical value where the amorphisation takes place

  11. Weighted Bergman Kernels for Logarithmic Weights

    Czech Academy of Sciences Publication Activity Database

    Engliš, Miroslav

    2010-01-01

    Roč. 6, č. 3 (2010), s. 781-813 ISSN 1558-8599 R&D Projects: GA AV ČR IAA100190802 Keywords : Bergman kernel * Toeplitz operator * logarithmic weight * pseudodifferential operator Subject RIV: BA - General Mathematics Impact factor: 0.462, year: 2010 http://www.intlpress.com/site/pub/pages/journals/items/pamq/content/vols/0006/0003/a008/

  12. Body Weight - Multiple Languages

    Science.gov (United States)

    ... Supplements Videos & Tools You Are Here: Home → Multiple Languages → All Health Topics → Body Weight URL of this page: https://medlineplus.gov/ ... V W XYZ List of All Topics All Body Weight - Multiple Languages To use the sharing features on this page, ...

  13. Concurrent weighted logic

    DEFF Research Database (Denmark)

    Xue, Bingtian; Larsen, Kim Guldstrand; Mardare, Radu Iulian

    2015-01-01

    We introduce Concurrent Weighted Logic (CWL), a multimodal logic for concurrent labeled weighted transition systems (LWSs). The synchronization of LWSs is described using dedicated functions that, in various concurrency paradigms, allow us to encode the compositionality of LWSs. To reflect these......-completeness results for this logic. To complete these proofs we involve advanced topological techniques from Model Theory....

  14. Unexplained Weight Loss

    Science.gov (United States)

    ... weight is affected by your calorie intake, activity level, overall health, age, nutrient absorption, and economic and social factors. If you're losing weight without trying and you're concerned about it, consult your doctor — as a rule of thumb, losing more than 5 ...

  15. Thyroid and Weight

    Science.gov (United States)

    ... Hypothyroidism in Children and Adolescents Pediatric Differentiated Thyroid Cancer Thyroid Nodules in Children and Adolescents Thyroid and Weight Resources Thyroid and Weight Brochure PDF En Español La Tiroides y el Peso El folleto de La Tiroides y el ...

  16. Adolescent Weight Status

    DEFF Research Database (Denmark)

    Hjort Kjelldgaard, Heidi; Holstein, Bjørn Evald; Due, Pernille

    2017-01-01

    day) communication with friends through cellphones, SMS messages, or Internet (1.66, 1.03-2.67). In the full population, overweight/obese weight status was associated with not perceiving best friend as a confidant (1.59, 1.11-2.28). No associations were found between weight status and number of close...

  17. Isotopes and atomic weights

    International Nuclear Information System (INIS)

    Zhang Qinglian

    1990-01-01

    A review of the chemical and mass spectrometric methods of determining the atomic weights of elements is presented. A, special discussion is devoted to the calibration of the mass spectrometer with highly enriched isotopes. It is illustrated by the recent work on europium. How to choose the candidate element for new atomic weight determination forms the last section of the article

  18. Kinetics of cellular transformation and competing precipitation mechanisms during sub-eutectoid annealing of U10Mo alloys

    Energy Technology Data Exchange (ETDEWEB)

    Jana, Saumyadeep; Devaraj, Arun; Kovarik, Libor; Arey, Bruce W.; Sweet, Lucas E.; Varga, Tamas; Lavender, Curt A.; Joshi, Vineet V.

    2017-11-01

    Transformation kinetics of metastable body-centered cubic γ-UMo phase in U-10 wt.percent Mo alloy during annealing at sub-eutectoid temperatures of 500C and 400C has been determined as a function of time using detailed microstructural characterization by scanning electron microscopy, X-ray diffraction analysis, scanning transmission electron microscopy, and atom probe tomography. Based on the results, we found that the phase transformation is initiated by cellular transformation at both the temperatures, which results in formation of a lamellar microstructure along prior γ-UMo grain boundaries.

  19. Overestimation of own body weights in female university students: associations with lifestyles, weight control behaviors and depression

    OpenAIRE

    Kim, Miso; Lee, Hongmie

    2010-01-01

    The study aimed to analyze the lifestyles, weight control behavior, dietary habits, and depression of female university students. The subjects were 532 students from 8 universities located in 4 provinces in Korea. According to percent ideal body weight, 33 (6.4%), 181 (34.0%), 283 (53.2%), 22 (4.1%) and 13 (2.5%) were severely underweight, underweight, normal, overweight and obese, respectively, based on self-reported height and weight. As much as 64.1% and only 2.4%, respectively, overestima...

  20. Phase equilibria in the system Li2O - MoO3 - Sc2O3

    International Nuclear Information System (INIS)

    Safonov, V.V.; Chaban, N.G.; Porotnikov, N.V.

    1984-01-01

    Using the methods of DTA and X-ray phase analysis, interaction of components in the system Li 2 O-MoO 3 -Sc 2 O 3 in concentration range, adjacent to the vertex of MoO 3 , has been studied. Projection of the Li 2 MoO 4 -MoO 3 -Sc 2 (MoO 4 ) 3 system liquidus on concentrational triangle of the compositions Li 2 O-MoO 3 -Sc 2 O 3 , which consists of the fields of primary separation of Li 2 MoO 4 , Li 2 Mo 5 O 17 , Li 2 Mo 4 O 13 , MoO 3 , Sc 2 (MoO 4 ) 3 , Li 3 Sc(MoO 4 ) 3 and LiSc(MoO 4 ) 2 , is built

  1. Reciprocity of weighted networks.

    Science.gov (United States)

    Squartini, Tiziano; Picciolo, Francesco; Ruzzenenti, Franco; Garlaschelli, Diego

    2013-01-01

    In directed networks, reciprocal links have dramatic effects on dynamical processes, network growth, and higher-order structures such as motifs and communities. While the reciprocity of binary networks has been extensively studied, that of weighted networks is still poorly understood, implying an ever-increasing gap between the availability of weighted network data and our understanding of their dyadic properties. Here we introduce a general approach to the reciprocity of weighted networks, and define quantities and null models that consistently capture empirical reciprocity patterns at different structural levels. We show that, counter-intuitively, previous reciprocity measures based on the similarity of mutual weights are uninformative. By contrast, our measures allow to consistently classify different weighted networks according to their reciprocity, track the evolution of a network's reciprocity over time, identify patterns at the level of dyads and vertices, and distinguish the effects of flux (im)balances or other (a)symmetries from a true tendency towards (anti-)reciprocation.

  2. Weight discrimination and bullying.

    Science.gov (United States)

    Puhl, Rebecca M; King, Kelly M

    2013-04-01

    Despite significant attention to the medical impacts of obesity, often ignored are the negative outcomes that obese children and adults experience as a result of stigma, bias, and discrimination. Obese individuals are frequently stigmatized because of their weight in many domains of daily life. Research spanning several decades has documented consistent weight bias and stigmatization in employment, health care, schools, the media, and interpersonal relationships. For overweight and obese youth, weight stigmatization translates into pervasive victimization, teasing, and bullying. Multiple adverse outcomes are associated with exposure to weight stigmatization, including depression, anxiety, low self-esteem, body dissatisfaction, suicidal ideation, poor academic performance, lower physical activity, maladaptive eating behaviors, and avoidance of health care. This review summarizes the nature and extent of weight stigmatization against overweight and obese individuals, as well as the resulting consequences that these experiences create for social, psychological, and physical health for children and adults who are targeted. Copyright © 2013 Elsevier Ltd. All rights reserved.

  3. -MoS2 Lateral Heterojunctions

    KAUST Repository

    Li, Ming-yang

    2018-02-28

    2D layered heterostructures have attracted intensive interests due to their unique optical, transport, and interfacial properties. The laterally stitched heterojunction based on dissimilar 2D transition metal dichalcogenides forms an intrinsic p–n junction without the necessity of applying an external voltage. However, no scalable processes are reported to construct the devices with such lateral heterostructures. Here, a scalable strategy, two-step and location-selective chemical vapor deposition, is reported to synthesize self-aligned WSe2–MoS2 monolayer lateral heterojunction arrays and demonstrates their light-emitting devices. The proposed fabrication process enables the growth of high-quality interfaces and the first successful observation of electroluminescence at the WSe2–MoS2 lateral heterojunction. The electroluminescence study has confirmed the type-I alignment at the interface rather than commonly believed type-II alignment. This self-aligned growth process paves the way for constructing various 2D lateral heterostructures in a scalable manner, practically important for integrated 2D circuit applications.

  4. Percent relative cumulative frequency analysis in indirect calorimetry: application to studies of transgenic mice.

    Science.gov (United States)

    Riachi, Marc; Himms-Hagen, Jean; Harper, Mary-Ellen

    2004-12-01

    Indirect calorimetry is commonly used in research and clinical settings to assess characteristics of energy expenditure. Respiration chambers in indirect calorimetry allow measurements over long periods of time (e.g., hours to days) and thus the collection of large sets of data. Current methods of data analysis usually involve the extraction of only a selected small proportion of data, most commonly the data that reflects resting metabolic rate. Here, we describe a simple quantitative approach for the analysis of large data sets that is capable of detecting small differences in energy metabolism. We refer to it as the percent relative cumulative frequency (PRCF) approach and have applied it to the study of uncoupling protein-1 (UCP1) deficient and control mice. The approach involves sorting data in ascending order, calculating their cumulative frequency, and expressing the frequencies in the form of percentile curves. Results demonstrate the sensitivity of the PRCF approach for analyses of oxygen consumption (.VO2) as well as respiratory exchange ratio data. Statistical comparisons of PRCF curves are based on the 50th percentile values and curve slopes (H values). The application of the PRCF approach revealed that energy expenditure in UCP1-deficient mice housed and studied at room temperature (24 degrees C) is on average 10% lower (p lower environmental temperature, there were no differences in .VO2 between groups. The latter is likely due to augmented shivering thermogenesis in UCP1-deficient mice compared with controls. With the increased availability of murine models of metabolic disease, indirect calorimetry is increasingly used, and the PRCF approach provides a novel and powerful means for data analysis.

  5. Increased circulating fibrocytes are associated with higher reticulocyte percent in children with sickle cell anemia.

    Science.gov (United States)

    Karafin, Matthew S; Dogra, Shibani; Rodeghier, Mark; Burdick, Marie; Mehrad, Borna; Rose, C Edward; Strieter, Robert M; DeBaun, Michael R; Strunk, Robert C; Field, Joshua J

    2016-03-01

    Interstitial lung disease is common in patients with sickle cell anemia (SCA). Fibrocytes are circulating cells implicated in the pathogenesis of pulmonary fibrosis and airway remodeling in asthma. In this study, we tested the hypotheses that fibrocyte levels are: (1) increased in children with SCA compared to healthy controls, and (2) associated with pulmonary disease. Cross-sectional cohort study of children with SCA who participated in the Sleep Asthma Cohort Study. Fibrocyte levels were obtained from 45 children with SCA and 24 controls. Mean age of SCA cases was 14 years and 53% were female. In children with SCA, levels of circulating fibrocytes were greater than controls (P < 0.01). The fibrocytes expressed a hierarchy of chemokine receptors, with CXCR4 expressed on the majority of cells and CCR2 and CCR7 expressed on a smaller subset. Almost half of fibrocytes demonstrated α-smooth muscle actin activation. Increased fibrocyte levels were associated with a higher reticulocyte count (P = 0.03) and older age (P = 0.048) in children with SCA. However, children with increased levels of fibrocytes were not more likely to have asthma or lower percent predicted forced expiratory volume in 1 sec/forced vital capacity (FEV1 /FVC) or FEV1 than those with lower fibrocyte levels. Higher levels of fibrocytes in children with SCA compared to controls may be due to hemolysis. Longitudinal studies may be able to better assess the relationship between fibrocyte level and pulmonary dysfunction. © 2015 Wiley Periodicals, Inc.

  6. Comparison of breast percent density estimation from raw versus processed digital mammograms

    Science.gov (United States)

    Li, Diane; Gavenonis, Sara; Conant, Emily; Kontos, Despina

    2011-03-01

    We compared breast percent density (PD%) measures obtained from raw and post-processed digital mammographic (DM) images. Bilateral raw and post-processed medio-lateral oblique (MLO) images from 81 screening studies were retrospectively analyzed. Image acquisition was performed with a GE Healthcare DS full-field DM system. Image post-processing was performed using the PremiumViewTM algorithm (GE Healthcare). Area-based breast PD% was estimated by a radiologist using a semi-automated image thresholding technique (Cumulus, Univ. Toronto). Comparison of breast PD% between raw and post-processed DM images was performed using the Pearson correlation (r), linear regression, and Student's t-test. Intra-reader variability was assessed with a repeat read on the same data-set. Our results show that breast PD% measurements from raw and post-processed DM images have a high correlation (r=0.98, R2=0.95, p<0.001). Paired t-test comparison of breast PD% between the raw and the post-processed images showed a statistically significant difference equal to 1.2% (p = 0.006). Our results suggest that the relatively small magnitude of the absolute difference in PD% between raw and post-processed DM images is unlikely to be clinically significant in breast cancer risk stratification. Therefore, it may be feasible to use post-processed DM images for breast PD% estimation in clinical settings. Since most breast imaging clinics routinely use and store only the post-processed DM images, breast PD% estimation from post-processed data may accelerate the integration of breast density in breast cancer risk assessment models used in clinical practice.

  7. Weighing every day matters: daily weighing improves weight loss and adoption of weight control behaviors.

    Science.gov (United States)

    Steinberg, Dori M; Bennett, Gary G; Askew, Sandy; Tate, Deborah F

    2015-04-01

    Daily weighing is emerging as the recommended self-weighing frequency for weight loss. This is likely because it improves adoption of weight control behaviors. To examine whether weighing every day is associated with greater adoption of weight control behaviors compared with less frequent weighing. Longitudinal analysis of a previously conducted 6-month randomized controlled trial. Overweight men and women in Chapel Hill, NC, participated in the intervention arm (N=47). The intervention focused on daily weighing for weight loss using an e-scale that transmitted weights to a study website, along with weekly e-mailed lessons and tailored feedback on daily weighing adherence and weight loss progress. We gathered objective data on self-weighing frequency from the e-scales. At baseline and 6 months, weight change was measured in the clinic and weight control behaviors (total items=37), dietary strategies, and calorie expenditure from physical activity were assessed via questionnaires. Calorie intake was assessed using an online 24-hour recall tool. We used χ(2) tests to examine variation in discrete weight control behaviors and linear regression models to examine differences in weight, dietary strategies, and calorie intake and expenditure by self-weighing frequency. Fifty-one percent of participants weighed every day (n=24) over 6 months. The average self-weighing frequency among those weighing less than daily (n=23) was 5.4±1.2 days per week. Daily weighers lost significantly more weight compared with those weighing less than daily (mean difference=-6.1 kg; 95% CI -10.2 to -2.1; P=0.004). The total number of weight control behaviors adopted was greater among daily weighers (17.6±7.6 vs 11.2±6.4; P=0.004). There were no differences by self-weighing frequency in dietary strategies, calorie intake, or calorie expenditure. Weighing every day led to greater adoption of weight control behaviors and produced greater weight loss compared with weighing most days of the

  8. Does One Know the Properties of a MICE Solid or Liquid Absorber to Better than 0.3 Percent?

    International Nuclear Information System (INIS)

    Green, Michael A.; Yang, Stephanie Q.

    2006-01-01

    This report discusses the report discusses whether the MICE absorbers can be characterized to ±0.3 percent, so that one predict absorber ionization cooling within the absorber. This report shows that most solid absorbers can be characterized to much better than ±0.3 percent. The two issues that dominate the characterization of the liquid cryogen absorbers are the dimensions of the liquid in the vessel and the density of the cryogenic liquid. The thickness of the window also plays a role. This report will show that a liquid hydrogen absorber can be characterized to better than ±0.3 percent, but a liquid helium absorber cannot be characterized to better and ±1 percent

  9. Map of percent scleractinian coral cover along camera tows and ROV tracks in the Auau Channel, Island of Maui, Hawaii

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral overlaid on bathymetry and landsat imagery. Optical data were...

  10. EnviroAtlas - Percent of Each 12-Digit HUC in the Contiguous U.S. with Potentially Restorable Wetlands

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset shows the percent of each 12-digit Hydrologic Unit (HUC) subwatershed in the contiguous U.S. with potentially restorable wetlands. Beginning...

  11. EnviroAtlas - Percent Land Cover with Potentially Restorable Wetlands on Agricultural Land per 12-Digit HUC - Contiguous United States

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas dataset shows the percent land cover with potentially restorable wetlands on agricultural land for each 12-digit Hydrologic Unit (HUC) watershed in...

  12. Map of percent scleractinian coral cover and sand along camera tows and ROV tracks of West Maui, Hawaii

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This map displays optical validation observation locations and percent coverage of scleractinian coral and sand overlaid on bathymetry and landsat imagery. Optical...

  13. Voltage profile, structural prediction, and electronic calculations for MgxMo6S8

    CSIR Research Space (South Africa)

    Kganyago, KR

    2003-03-01

    Full Text Available the binary Mo6S8 and MgAMo6S8 ~see Table III!, the Mo-Mo distances decrease by (0.521)%. This decrease corresponds to an an- isotropic contraction of the Mo6 octahedron. The Mo cluster of the rhombohedral compounds forms an elongated octahe- dron of symmetry...

  14. FINANCIAL PROBLEMS OF BOTTOM 40 PERCENT BUMIPUTERA IN MALAYSIA: A POSSIBLE SOLUTION THROUGH WAQF-BASED CROWDFUNDING

    OpenAIRE

    Abidullah ABID; Muhammad Hakimi Mohd SHAFIAI

    2017-01-01

    Low savings by the bottom 40 percent Bumiputera triggered low wealth accumulation and greater wealth inequality. The issue behind the low savings is the increase in food prices, taxes, and interest rates for the borrowers. In response to these problems, the Malaysian government provides cash transfer BRIM as one of redistributive measures. However, it is still not enough as many of the bottom 40 percent are neglected to avail the facility. In such circumstances, the role of community-based ca...

  15. Lattice structures and electronic properties of MO/MoSe2 interface from first-principles calculations

    Science.gov (United States)

    Zhang, Yu; Tang, Fu-Ling; Xue, Hong-Tao; Lu, Wen-Jiang; Liu, Jiang-Fei; Huang, Min

    2015-02-01

    Using first-principles plane-wave calculations within density functional theory, we theoretically studied the atomic structure, bonding energy and electronic properties of the perfect Mo (110)/MoSe2 (100) interface with a lattice mismatch less than 4.2%. Compared with the perfect structure, the interface is somewhat relaxed, and its atomic positions and bond lengths change slightly. The calculated interface bonding energy is about -1.2 J/m2, indicating that this interface is very stable. The MoSe2 layer on the interface has some interface states near the Fermi level, the interface states are mainly caused by Mo 4d orbitals, while the Se atom almost have no contribution. On the interface, Mo-5s and Se-4p orbitals hybridize at about -6.5 to -5.0 eV, and Mo-4d and Se-4p orbitals hybridize at about -5.0 to -1.0 eV. These hybridizations greatly improve the bonding ability of Mo and Se atom in the interface. By Bader charge analysis, we find electron redistribution near the interface which promotes the bonding of the Mo and MoSe2 layer.

  16. First-principles study of van der Waals interactions in MoS2 and MoO3

    International Nuclear Information System (INIS)

    Peelaers, H; Van de Walle, C G

    2014-01-01

    Van der Waals interactions play an important role in layered materials such as MoS 2 and MoO 3 . Within density functional theory, several methods have been developed to explicitly include van der Waals interactions. We compare the performance of several of these functionals in describing the structural and electronic properties of MoS 2 and MoO 3 . We include functionals based on the local density or generalized gradient approximations, but also based on hybrid functionals. The coupling of the semiempirical Grimme D2 method with the hybrid functional HSE06 is shown to lead to a very good description of both structural and electronic properties. (paper)

  17. The fracture toughness and DBTT of MoB particle-reinforced MoSi2 composites

    International Nuclear Information System (INIS)

    Xiong Zhi; Wang Gang; Jiang Wan

    2005-01-01

    The room temperature fracture toughness and the high temperature DBTT of MoB particle-reinforced MoSi 2 composites were investigated using Vickers indentation technique and MSP testing method, respectively. Modified small punch (MSP) test is a method for evaluation of mechanical properties using very small specimens, and it's appropriate for the determination of strength and DBTT. It was found that the approximate fracture toughness of the composite is 1.3 times that of monolithic MoSi 2 , and its DBTT is 100 C higher than that of monolithic MoSi 2 materials. Cracks deflection is a probable mechanism responsible for this behavior. (orig.)

  18. Magnetoresistance in Co/2D MoS2/Co and Ni/2D MoS2/Ni junctions.

    Science.gov (United States)

    Zhang, Han; Ye, Meng; Wang, Yangyang; Quhe, Ruge; Pan, Yuanyuan; Guo, Ying; Song, Zhigang; Yang, Jinbo; Guo, Wanlin; Lu, Jing

    2016-06-28

    Semiconducting single-layer (SL) and few-layer MoS2 have a flat surface, free of dangling bonds. Using density functional theory coupled with non-equilibrium Green's function method, we investigate the spin-polarized transport properties of Co/2D MoS2/Co and Ni/2D MoS2/Ni junctions with MoS2 layer numbers of N = 1, 3, and 5. Well-defined interfaces are formed between MoS2 and metal electrodes. The junctions with a SL MoS2 spacer are almost metallic owing to the strong coupling between MoS2 and the ferromagnets, while those are tunneling with a few layer MoS2 spacer. Both large magnetoresistance and tunneling magnetoresistance are found when fcc or hcp Co is used as an electrode. Therefore, flat single- and few-layer MoS2 can serve as an effective nonmagnetic spacer in a magnetoresistance or tunneling magnetoresistance device with a well-defined interface.

  19. Size at birth, weight gain in infancy and childhood, and adult blood pressure in 5 low- and middle-income-country cohorts: when does weight gain matter?

    Science.gov (United States)

    Adair, Linda S; Martorell, Reynaldo; Stein, Aryeh D; Hallal, Pedro C; Sachdev, Harshpal S; Prabhakaran, Dorairaj; Wills, Andrew K; Norris, Shane A; Dahly, Darren L; Lee, Nanette R; Victora, Cesar G

    2009-05-01

    Promoting catch-up growth in malnourished children has health benefits, but recent evidence suggests that accelerated child weight gain increases adult chronic disease risk. We aimed to determine how birth weight (BW) and weight gain to midchildhood relate to blood pressure (BP) in young adults. We pooled data from birth cohorts in Brazil, Guatemala, India, the Philippines, and South Africa. We used conditional weight (CW), a residual of current weight regressed on prior weights, to represent deviations from expected weight gain from 0 to 12, 12 to 24, 24 to 48 mo, and 48 mo to adulthood. Adult BP and risk of prehypertension or hypertension (P/HTN) were modeled before and after adjustment for adult body mass index (BMI) and height. Interactions of CWs with small size-for-gestational age (SGA) at birth were tested. Higher CWs were associated with increased BP and odds of P/HTN, with coefficients proportional to the contribution of each CW to adult BMI. Adjusted for adult height and BMI, no child CW was associated with adult BP, but 1 SD of BW was related to a 0.5-mm Hg lower systolic BP and a 9% lower odds of P/HTN. BW and CW associations with systolic BP and P/HTN were not different between adults born SGA and those with normal BW, but higher CW at 48 mo was associated with higher diastolic BP in those born SGA. Greater weight gain at any age relates to elevated adult BP, but faster weight gains in infancy and young childhood do not pose a higher risk than do gains at other ages.

  20. Effects of anti-obesity drugs, diet, and exercise on weight-loss maintenance after a very-low-calorie diet or low-calorie diet: a systematic review and meta-analysis of randomized controlled trials123

    Science.gov (United States)

    Neovius, Martin; Hemmingsson, Erik

    2014-01-01

    Background: Weight-loss maintenance remains a major challenge in obesity treatment. Objective: The objective was to evaluate the effects of anti-obesity drugs, diet, or exercise on weight-loss maintenance after an initial very-low-calorie diet (VLCD)/low-calorie diet (LCD) period (obesity drugs (3 arms; n = 658), meal replacements (4 arms; n = 322), high-protein diets (6 arms; n = 865), dietary supplements (6 arms; n = 261), other diets (3 arms; n = 564), and exercise (5 arms; n = 347). During the VLCD/LCD period, the pooled mean weight change was −12.3 kg (median duration: 8 wk; range 3–16 wk). Compared with controls, anti-obesity drugs improved weight-loss maintenance by 3.5 kg [95% CI: 1.5, 5.5 kg; median duration: 18 mo (12–36 mo)], meal replacements by 3.9 kg [95% CI: 2.8, 5.0 kg; median duration: 12 mo (10–26 mo)], and high-protein diets by 1.5 kg [95% CI: 0.8, 2.1 kg; median duration: 5 mo (3–12 mo)]. Exercise [0.8 kg; 95% CI: −1.2, 2.8 kg; median duration: 10 mo (6–12 mo)] and dietary supplements [0.0 kg; 95% CI: −1.4, 1.4 kg; median duration: 3 mo (3–14 mo)] did not significantly improve weight-loss maintenance compared with control. Conclusion: Anti-obesity drugs, meal replacements, and high-protein diets were associated with improved weight-loss maintenance after a VLCD/LCD period, whereas no significant improvements were seen for dietary supplements and exercise. PMID:24172297

  1. Effects of anti-obesity drugs, diet, and exercise on weight-loss maintenance after a very-low-calorie diet or low-calorie diet: a systematic review and meta-analysis of randomized controlled trials.

    Science.gov (United States)

    Johansson, Kari; Neovius, Martin; Hemmingsson, Erik

    2014-01-01

    Weight-loss maintenance remains a major challenge in obesity treatment. The objective was to evaluate the effects of anti-obesity drugs, diet, or exercise on weight-loss maintenance after an initial very-low-calorie diet (VLCD)/low-calorie diet (LCD) period (obesity drugs (3 arms; n = 658), meal replacements (4 arms; n = 322), high-protein diets (6 arms; n = 865), dietary supplements (6 arms; n = 261), other diets (3 arms; n = 564), and exercise (5 arms; n = 347). During the VLCD/LCD period, the pooled mean weight change was -12.3 kg (median duration: 8 wk; range 3-16 wk). Compared with controls, anti-obesity drugs improved weight-loss maintenance by 3.5 kg [95% CI: 1.5, 5.5 kg; median duration: 18 mo (12-36 mo)], meal replacements by 3.9 kg [95% CI: 2.8, 5.0 kg; median duration: 12 mo (10-26 mo)], and high-protein diets by 1.5 kg [95% CI: 0.8, 2.1 kg; median duration: 5 mo (3-12 mo)]. Exercise [0.8 kg; 95% CI: -1.2, 2.8 kg; median duration: 10 mo (6-12 mo)] and dietary supplements [0.0 kg; 95% CI: -1.4, 1.4 kg; median duration: 3 mo (3-14 mo)] did not significantly improve weight-loss maintenance compared with control. Anti-obesity drugs, meal replacements, and high-protein diets were associated with improved weight-loss maintenance after a VLCD/LCD period, whereas no significant improvements were seen for dietary supplements and exercise.

  2. Mo-99 supply issues: Status report and lessons learned

    International Nuclear Information System (INIS)

    Ponsard, B.

    2010-01-01

    The worldwide supply of 99 Mo relies on a limited number of research reactors and processing facilities. Its production is essential for the nuclear medicine as 99m Tc, obtained from 99 Mo/ 99m Tc generators, is used in about 80% of the diagnostic nuclear imaging procedures. These applications represent yearly approximately 30 million examinations worldwide. The short half-life's of 99 Mo (66 hours) and its daughter 99m Tc (6 hours) require a regular supply of 99 Mo/ 99m Tc generators to hospitals or central radiopharmacies. Currently, there are only five nuclear reactors involved in the production of 99 Mo on industrial scale: NRU (Canada), HFR (Netherlands), BR2 (Belgium), OSIRIS (France) and SAFARI (South Africa). They irradiate highly enriched uranium targets for the production of about 95% of the available 99 Mo by four processing facilities: AECL/MDS NORDION (Canada), COVIDIEN (Netherlands), IRE (Belgium) and NTP (South Africa). However, these ageing reactors are subject to unscheduled shutdowns and longer maintenance periods making the 99 Mo supply chain vulnerable and unreliable. Several severe disruptions have been experienced since the fall 2005 due to the occurrence of problems at different stages of the supply chain: reactor outages, release of activity from processing facilities, recall of 99 Mo/ 99m Tc generators by the manufacturers, ... It is not expected that the situation will improve significantly in the near future. Therefore, several workshops have been organized in 2009 by the OECD Nuclear Energy Agency (NEA), the International Atomic Energy Agency (IAEA) and the Association of Imaging Producers and Equipment Suppliers (AIPES) to define measures that should be taken to secure the 99 Mo supply in the short, medium and long term. This paper summarizes the current status of the 99 Mo supply, discusses the ongoing plans for additional 99 Mo production capacity and outlines the issues for a reliable global supply chain. (author)

  3. Physical properties of monolithic U8 wt.%-Mo

    Science.gov (United States)

    Hengstler, R. M.; Beck, L.; Breitkreutz, H.; Jarousse, C.; Jungwirth, R.; Petry, W.; Schmid, W.; Schneider, J.; Wieschalla, N.

    2010-07-01

    As a possible high density fuel for research reactors, monolithic U8 wt.%-Mo ("U8Mo") was examined with regard to its structural, thermal and electric properties. X-ray diffraction by the Bragg-Brentano method was used to reveal the tetragonal lattice structure of rolled U8Mo. The specific heat capacity of cast U8Mo was determined by differential scanning calorimetry, its thermal diffusivity was measured by the laser flash method and its mass density by Archimedes' principle. From these results, the thermal conductivity of U8Mo in the temperature range from 40 °C to 250 °C was calculated; in the measured temperature range, it is in good accordance with literature data for UMo with 8 and 9 wt.% Mo, is higher than for 10 wt.% Mo and lower than for 5 wt.% Mo. The electric conductivity of rolled and cast U8Mo was measured by a four-wire method and the electron based part of the thermal conductivity calculated by the Wiedemann-Frantz law. Rolled and cast U8Mo was irradiated at about 150 °C with 80 MeV 127I ions to receive the same iodine ion density in the damage peak region as the fission product density in the fuel of a typical high flux reactor after the targeted nuclear burn-up. XRD analysis of irradiated U8Mo showed a change of the lattice parameters as well as the creation of UO 2 in the superficial sample regions; however, a phase change by irradiation was not observed. The determination of the electron based part of the thermal conductivity of the irradiated samples failed due to high measurement errors which are caused by the low thickness of the damage region in the ion irradiated samples.

  4. Design of a type - a transport package for 99Mo-99mTc Coltech generator

    International Nuclear Information System (INIS)

    Kothalkar, Chetan; Suryanarayana, G.V.; Dey, A.C.; Sachdev, S.S.; Choughule, N.; Murali, S.

    2012-01-01

    BRIT is launching a new product called 99 Mo- 99m Tc Coltech generator. The Coltech generator is a devise designed for the transport of 99 Mo radioisotope adsorbed on the acidic alumina in a sealed glass column (max dimensions: 13 mm diameter, 70 mm height) as the primary containment. At hospital end, 99m Tc, the daughter product of 99 Mo, can be eluted out from the generator using saline. The active column is fitted with a leak proof network of stainless steel needles. The glass column carrying 99 Mo is housed inside a lead shielding having minimum thickness of 50 mm all around, which serves as secondary containment. The shielding is housed inside the ABS shell which acts as tertiary containment, also provides protection to the needles, filters etc. Total weight of the generator is 16 kg. Based on the AERB code SC/TR-1 (being revised), 99 Mo- 99m Tc Coltech generator will be transported in a Type-A transport container. A transport package has been designed by following the code SC/TR-1. Principle design of the package is based on the package for transportation of the similar generator produced by POLATOM, Poland and the package is approved by the Polish regulatory authority. Components are manufactured locally taking care of lndian conditions. The package comprised of a MS drum (HOBBOCK) with tamper proof lockable MS lid and a handle to assist in lifting. For absorbing the shock during transportation, the generator assembly is packed inside the two pieces EPS top and bottom support. The package has been designed for transportation by all modes of transport. Since radioactive material is solid in form and sealed a glass column, it has been designed to sustain a free drop test of 1.2 m, in addition to other tests specified in SC/TR-1. During trial batches upto ∼ 1 Ci of 99 Mo generators were produced, packed in the same Type-A package and supplied to local nuclear medicine center RMC, Mumbai in BRIT vehicle in consultation with AERB. The radiometry of the packages

  5. ORDERED WEIGHTED DISTANCE MEASURE

    Institute of Scientific and Technical Information of China (English)

    Zeshui XU; Jian CHEN

    2008-01-01

    The aim of this paper is to develop an ordered weighted distance (OWD) measure, which is thegeneralization of some widely used distance measures, including the normalized Hamming distance, the normalized Euclidean distance, the normalized geometric distance, the max distance, the median distance and the min distance, etc. Moreover, the ordered weighted averaging operator, the generalized ordered weighted aggregation operator, the ordered weighted geometric operator, the averaging operator, the geometric mean operator, the ordered weighted square root operator, the square root operator, the max operator, the median operator and the min operator axe also the special cases of the OWD measure. Some methods depending on the input arguments are given to determine the weights associated with the OWD measure. The prominent characteristic of the OWD measure is that it can relieve (or intensify) the influence of unduly large or unduly small deviations on the aggregation results by assigning them low (or high) weights. This desirable characteristic makes the OWD measure very suitable to be used in many actual fields, including group decision making, medical diagnosis, data mining, and pattern recognition, etc. Finally, based on the OWD measure, we develop a group decision making approach, and illustrate it with a numerical example.

  6. MO-HF-C alloy composition

    International Nuclear Information System (INIS)

    Whelan, E.P.; Kalns, E.

    1987-01-01

    This patent describes, as an article of manufacture, a cast ingot of a molybdenum-hafnium-carbon alloy consisting essentially by weight of about 0.6% to about 1% Hf, about 0.045% to about 0.08% C, and the balance essentially molybdenum. The amount of Hf and C present are substantially stoichiometric with respect to HfC and within about +-15% of stoichiometry. The ingot is characterized in that it has a substantially less tendency to crack compared to alloys containing Hf in excess of about 1% by weight and carbon in excess of 0.08% by weight, without substantial diminution in strength properties of the alloy

  7. Misperception of weight status and associated factors among undergraduate students.

    Science.gov (United States)

    Mogre, Victor; Aleyira, Samuel; Nyaba, Rauf

    2015-01-01

    We compared participants' self-perception of their weight with the World Health Organisation (WHO) definition for BMI categories among undergraduate university students undertaking health related academic programmes in Ghana. Also, we investigated factors associated to the underestimation of weight status in this sample. This cross-sectional study was conducted among a sample of 368 undergraduate students. Anthropometric measurements of weight and height were measured with appropriate tools and computed into Body Mass Index (BMI) categorised based on WHO classifications. Waist and hip circumferences were also measured appropriately. Participants' self-perception of weight status was assessed by the question: How do you perceive your weight? (a) Underweight, (b) normal weight, (c) overweight, and (d) obese. The BMI-measured weight status was compared to the self-perceived weight status by cross-tabulation, Kappa statistics of agreement and χ(2) for trend analysis. Factors associated with misperception of weight status was measured using univariate and multivariable analysis. Thirteen percent (n=48) of the participants were overweight/obesity (BMI) and 31.5% had central obesity. Overall, 20.6% of the participants misperceived their weight status in which 78.9% of them underestimated it. Among overweight/obese participants, 41.7% self-perceived themselves accurately. Whereas 10.6% of normal weight participants underestimated their weight status, over half (58.3%) of overweight/obese participants did so. Factors that were associated with underestimation of weight status were having overweight/obesity (BMI) and central obesity. Underestimation of weight status was frequent. Health professionals and related government agencies should develop intervention programmes to empower young people to have accurate weight status perception. Copyright © 2015 Asian Oceanian Association for the Study of Obesity. Published by Elsevier Ltd. All rights reserved.

  8. A Preliminary Study to Enhance the Tribological Performance of CoCrMo Alloy by Fibre Laser Remelting for Articular Joint Implant Applications

    Directory of Open Access Journals (Sweden)

    Chi-Wai Chan

    2018-03-01

    Full Text Available CoCrMo alloy has long been used as a pairing femoral head material for articular joint implant applications because of its biocompatibility and reliable tribological performance. However, friction and wear issues are still present for CoCrMo (metal/CoCrMo (metal or CoCrMo (metal/ultrahigh molecular weight polyethylene (UHMWPE (plastic pairs in clinical observations. The particulate wear debris generated from the worn surfaces of CoCrMo or UHMWPE can pose a severe threat to human tissues, eventually resulting in the failure of implants and the need for revision surgeries. As a result, a further improvement in tribological properties of this alloy is still needed, and it is of great interest to both the implant manufacturers and clinical surgeons. In this study, the surface of CoCrMo alloy was laser-treated by a fibre laser system in an open-air condition (i.e., no gas chamber required. The CoCrMo surfaces before and after laser remelting were analysed and characterised by a range of mechanical tests (i.e., surface roughness measurement and Vickers micro-hardness test and microstructural analysis (i.e., XRD phase detection. The tribological properties were assessed by pin-on-disk tribometry and dynamic light scattering (DLS. Our results indicate that the laser-treated surfaces demonstrated a friction-reducing effect for all the tribopairs (i.e., CoCrMo against CoCrMo and CoCrMo against UHHMWPE and enhanced wear resistance for the CoCrMo/CoCrMo pair. Such beneficial effects are chiefly attributable to the presence of the laser-formed hard coating on the surface. Laser remelting possesses several competitive advantages of being a clean, non-contact, fast, highly accurate and automated process compared to other surface coating methods. The promising results of this study point to the possibility that laser remelting can be a practical and effective surface modification technique to further improve the tribological performance of Co

  9. Light-weight plastination.

    Science.gov (United States)

    Steinke, Hanno; Rabi, Suganthy; Saito, Toshiyuki; Sawutti, Alimjan; Miyaki, Takayoshi; Itoh, Masahiro; Spanel-Borowski, Katharina

    2008-11-20

    Plastination is an excellent technique which helps to keep the anatomical specimens in a dry, odourless state. Since the invention of plastination technique by von Hagens, research has been done to improve the quality of plastinated specimens. In this paper, we have described a method of producing light-weight plastinated specimens using xylene along with silicone and in the final step, substitute xylene with air. The finished plastinated specimens were light-weight, dry, odourless and robust. This method requires less use of resin thus making the plastination technique more cost-effective. The light-weight specimens are easy to carry and can easily be used for teaching.

  10. Thermal expansion studies on Th(MoO4)2, Na2Th(MoO4)3 and Na4Th(MoO4)4

    International Nuclear Information System (INIS)

    Keskar, Meera; Krishnan, K.; Dahale, N.D.

    2008-01-01

    Thermal expansion behavior of Th(MoO 4 ) 2 , Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 was studied under vacuum in the temperature range of 298-1123 K by high temperature X-ray diffractometer. Th(MoO 4 ) 2 was synthesized by reacting ThO 2 with 2 mol of MoO 3 , at 1073 K in air and Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were prepared by reacting Th(MoO 4 ) 2 with 1 and 2 mol of Na 2 MoO 4 , respectively at 873 K in air. The XRD data of Th(MoO 4 ) 2 was indexed on orthorhombic system where as XRD data of Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were indexed on tetragonal system. The lattice parameters and cell volume of all the three compounds, fit into polynomial expression with respect to temperature, showed positive thermal expansion (PTE) up to 1123 K. The average value of thermal expansion coefficients for Th(MoO 4 ) 2 , Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were determined from the high temperature data

  11. Study of the water-gas shift reaction on Mo2C/Mo catalytic coatings for application in microstructured fuel processors

    NARCIS (Netherlands)

    Rebrov, E.V.; Kuznetsov, S.A.; Croon, de M.H.J.M.; Schouten, J.C.

    2007-01-01

    The activity and stability of two types of molybdenum carbide coatings deposited on molybdenum substrates (Mo2C/Mo) were compared in the water-gas shift reaction at 513–631 K. The activity of the Mo2C/Mo coatings obtained by carburization of preoxidized molybdenum substrates in a CH4/H2 mixture at

  12. LEUbased Fission Mo-99 Process with Reduced Solid Wastes

    International Nuclear Information System (INIS)

    Lee, Seungkon; Lee, Suseung; Jung, Sunghee; Hong, Soonbog; Jang, Kyungduk; Choi, Sang Mu; Lee, Jun Sig; Lim, Incheol

    2014-01-01

    99m Tc emits 140 keV of very low gamma-ray radiation energy, as low as conventional diagnostic X-ray, and has short half-life of 6.0058 hours. Therefore, as radioactive tracer, 99m Tc provides high quality diagnostic images but keeps total patient radiation exposure low. Depending on the tagging pharmaceuticals and procedures, 99m Tc can be applied for the diagnostics of various target organs and diseases: brain, myocardium, thyroid, lungs, liver, gallbladder, kidneys, skeleton, blood and tumors. More than 95% of 99 Mo is produced through fission of 235 U worldwide because, 99m o generated from the fission (fission 99 Mo) exhibits very high specific activity (<100 Ci/g). Over 90% of fission 99 Mo producers have been used highly enriched uranium (HEU) targets so far. However, the IAEA recommends the use of low enriched uranium (LEU) to the 99 Mo producers for nonproliferation reason. These days, worldwide 99 Mo supply is not only insufficient but also unstable. Because, most of the main 99 Mo production reactors are about 50 years old and suffered from frequent and unscheduled shutdown. Planned weekly productivity of 2000 Ci fission 99 Mo, in a 6-day reference, will cover 100% domestic demand of Korea, as well as 20% of international market. It is expected to replace 4.3 million USD ($800/Ci) of 99 Mo import for domestic market while exporting 82.8 million USD for world market, annually

  13. Mullite/Mo interfaces formed by Intrusion bonding

    Energy Technology Data Exchange (ETDEWEB)

    Bartolome, Jose F.; Diaz, Marcos; Moya, Jose S.; Saiz, Eduardo; Tomsia, Antoni P.

    2003-04-30

    The microstructure and strength of Mo/mullite interfaces formed by diffusion bonding at 1650 C has been analyzed. Interfacial metal-ceramic interlocking contributes to flexural strength of approx. 140 MPa as measured by 3 point bending. Saturation of mullite with MoO2 does not affect the interfacial strength.

  14. Mo-Si-B-Based Coatings for Ceramic Base Substrates

    Science.gov (United States)

    Perepezko, John Harry (Inventor); Sakidja, Ridwan (Inventor); Ritt, Patrick (Inventor)

    2015-01-01

    Alumina-containing coatings based on molybdenum (Mo), silicon (Si), and boron (B) ("MoSiB coatings") that form protective, oxidation-resistant scales on ceramic substrate at high temperatures are provided. The protective scales comprise an aluminoborosilicate glass, and may additionally contain molybdenum. Two-stage deposition methods for forming the coatings are also provided.

  15. Preparation of a gel of zirconium molybdate for use in the generators of 99 Mo - 99m Tc prepared with 99 Mo produced by the 98 Mo(n,γ)99 Mo reaction

    International Nuclear Information System (INIS)

    Osso Junior, Joao A.; Lima, Ana Lucia V.P.; Silva, Nestor C. da; Nieto, Renata C.; Velosa, Adriana C. de

    1998-01-01

    IPEN develops a project concerning the preparation of a gel of Zirconium Molybdate for use in the generators of 99 Mo- 99m Tc . 99m Tc is the most used radioisotope in nuclear medicine diagnosis procedures and nowadays the generators are being prepared with imported 99 Mo, produced by 235 U fission. The production of 99 Mo by the 98 Mo(n, γ) 99 Mo reaction is now possible because of the power upgrade of IPEN's IEA-R1 reactor, from 2 to 5 MW. This work describes the preparation method of Zirconium Molybdate gel that will be used in the 99 Mo- 99m Tc generators. The gel is prepared by the chemical reaction between Mo, in Mo O 3 form, and Zr, in Zr O Cl 2 .8H 2 O form. After the reaction, the gel is filtered, dried and cracked with saline solution. The product is then loaded into glass columns for use as 99m Tc generator. The results showed the good quality of the gel prepared at laboratory level and of the generators evaluated. (author)

  16. Mullite/Mo interfaces formed by Intrusion bonding

    OpenAIRE

    Bartolome, Jose F.; Diaz, Marcos; Moya, Jose S.; Saiz, Eduardo; Tomsia, Antoni P.

    2003-01-01

    The microstructure and strength of Mo/mullite interfaces formed by diffusion bonding at 1650oC has been analyzed. Interfacial metal-ceramic interlocking contributes to flexural strength of approx. 140 MPa as measured by 3 point bending. Saturation of mullite with MoO2 does not affect the interfacial strength.

  17. Ammonia treated Mo/AC catalysts for CO hydrogenation with ...

    Indian Academy of Sciences (India)

    SHARIF F ZAMAN

    the influence of acid treated AC as a support with K-Ni-. Mo active ... K-Ni-Mo/AC catalyst was more selective to oxygenates. (>40% ... mineral impurities (K, Si, Sn and Fe) <1%. ...... edge technical support with thanks Science and Technology.

  18. Development of Fission Mo-99 Process for LEU Dispersion Target

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seung Kon; Lee, Su Seung; Hong, Soon Bog; Jang, Kyung Duk; Park, Ul Jae; Lee, Jun Sig [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    KAERI (Korea Atomic Energy Research Institute) is developing LEU-based fission {sup 99}Mo production process which is connected to the new research reactor (Kijang New Research Reactor, KJRR), which is being constructed in Gijang, Busan, Korea. Historically, the most fission {sup 99}Mo producers have been used highly enriched uranium (HEU) targets so far. However, to reduce the use of HEU in private sector for non-proliferation, {sup 99}Mo producers are forced to convert their HEU-based process to use low enriched uranium (LEU) targets. Economic impact of a target conversion from HEU to LEU is significant. Overall cost for the production of the fission {sup 99}Mo increases significantly with the conversion of fission {sup 99}Mo targets from HEU to LEU. It is not only because the yield of LEU is only 50% of HEU, but also because radioactive waste production increases 200%. On the basis, worldwide efforts on the development of {sup 99}Mo production process that is optimized for the LEU target become an important issue. In this study, fission {sup 99}Mo process with non-irradiated LEU targets was presented except separation and purification steps. Pre- and post-irradiation tests of the fission {sup 99}Mo target will be done in 4th quarter of 2016.

  19. Toroidal deuteron accelerator for Mo-98 neutron activation

    International Nuclear Information System (INIS)

    Araujo, Wagner L.; Campos, Tarcisio P.R. Universidade Federal de Minas Gerais

    2017-01-01

    The radionuclide Tc- 99m is the most useful radioisotope in nuclear medicine. It can be produced by the Mo-99 beta minus decay. Mo-99 has often been produced in a high- flux nuclear reactor through radioactive neutron capture reactions on Mo-98. The present paper provides a preliminary design of a toroidal transmutation system (TTS) based on a toroidal compact deuteron accelerator, which can provide the Mo-98 transmutation into Mo-99. This system is essentially composed of a multi-aperture plasma electrode and a target, submitted to 180 kV, where a positive deuteron beam is accelerated toward a titanium-target loaded with deuterium in which nuclear d-d fusion reactions are induced. The Particle Studio package of the Computer Simulation Technology (CST) software was applied to design, simulate and optimize the deuteron beam on the target. MCNP code provided to neutronic analysis. Based on electromagnetic and neutronic simulations, the neutron yield and reaction rates were estimated. The simulated data allowed appraising the Mo-99 activity. A TTS, in a specific configuration, could produce a total deuterium current of 1.6 A at the target and a neutron yield of 10 13 n.s -1 . In a arrangement of 30 column samples, TTS provides 230 mCi s -1 Mo 99 in each column, which represents 80% of Tc-99m in secular equilibrium. As conclusion, the system holds potential for generating Mo-99 and Tc-99m in a suitable activity in secular equilibrium. (author)

  20. Development of Fission Mo-99 Process for LEU Dispersion Target

    International Nuclear Information System (INIS)

    Lee, Seung Kon; Lee, Su Seung; Hong, Soon Bog; Jang, Kyung Duk; Park, Ul Jae; Lee, Jun Sig

    2016-01-01

    KAERI (Korea Atomic Energy Research Institute) is developing LEU-based fission 99 Mo production process which is connected to the new research reactor (Kijang New Research Reactor, KJRR), which is being constructed in Gijang, Busan, Korea. Historically, the most fission 99 Mo producers have been used highly enriched uranium (HEU) targets so far. However, to reduce the use of HEU in private sector for non-proliferation, 99 Mo producers are forced to convert their HEU-based process to use low enriched uranium (LEU) targets. Economic impact of a target conversion from HEU to LEU is significant. Overall cost for the production of the fission 99 Mo increases significantly with the conversion of fission 99 Mo targets from HEU to LEU. It is not only because the yield of LEU is only 50% of HEU, but also because radioactive waste production increases 200%. On the basis, worldwide efforts on the development of 99 Mo production process that is optimized for the LEU target become an important issue. In this study, fission 99 Mo process with non-irradiated LEU targets was presented except separation and purification steps. Pre- and post-irradiation tests of the fission 99 Mo target will be done in 4th quarter of 2016

  1. 77 FR 29875 - Establishment of Class E Airspace; Houston, MO

    Science.gov (United States)

    2012-05-21

    ...-0903; Airspace Docket No. 11-ACE-20] Establishment of Class E Airspace; Houston, MO AGENCY: Federal... at Houston, MO. Controlled airspace is necessary to accommodate new Area Navigation (RNAV) Standard Instrument Approach Procedures at Houston Memorial Airport. The FAA is taking this action to enhance the...

  2. Mo-99 production by fission and future projections

    International Nuclear Information System (INIS)

    Carranza, E.C.; Novello, A.; Bronca, M.; Cestau, D.; Bavaro, R.; Centurion, R.; Bravo, C.; Bronca, P.; Gualda, E.; Fraguas, F.; Giomi, A.; Ivaldi, L.

    2012-01-01

    Description of the I-131 and Mo-99 production process: The process starts with the irradiation of uranium-aluminum mini plates in the RA-3, Argentinean Reactor No.3, Ezeiza Atomic Center. In a nuclear reactor there is a constant flow of neutrons and when a neutron with proper energy impacts on a nucleus of U-235, it is absorbed at the same time generate an unstable configuration nuclear. For this reason, the nucleus formed is fission, getting two different atoms. Approximately 6% of the fissions produce Mo-99 and 3% produce I-131; the percentage remaining corresponds to formation of atoms without interest for use in medicine. In conclusion, the objective of the process developed in the Fission Plant, is starting from uranium mini plates, separate the Mo-99 and I-131 generated, the remaining elements formed. - Evolution of Mo-99 Production in the last 10 years: The Fission Mo-99 Plant Production begins routine production of Mo-99 in 1985, using targets made of uranium enriched at 90% U-235. In the 1990s, global concern regarding the use of highly enriched uranium, due to non-proliferation issues, caused the interruption of supply of nuclear material (HEU enriched at 90% of U-235). Following this, Argentina developed target based on low-enriched uranium (less than 20% U-235), becoming in 2002 the first country in the world to produce Mo-99 with LEU targets. From 2002 to date, the activity produced of Mo-99 has been tripled annually (author)

  3. A review on the process technology for Mo-99 production

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Hoh; Yoo, Jae Hyung; Jung, Won Myung; Lee, Kyoo Il; Woo, Moon Sik; Hwang, Doo Sung; Kim, Yun Koo [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1994-07-01

    Tc-99m is most frequently used in nuclear medical diagnostics because of its favourable nuclear properties and reasonable prices, and the demand of Tc-99m, is on the increase recently. Mo-99, the parent radionuclide of Tc-99m, is the only source of Tc-99m. This review described overall aspects of process technologies for Mo-99 production. Firstly, the chemical, physical and radioactive properties of Tc-99m, Mo-99 were examined to understand Mo-99 separation process. Also, the technology for Mo-99 production with both the neutron capture and nuclear fission method were examined. But the neutron capture method was scarcely used for large production of Mo-99 because of its low specific activity and high production cost. This review also described mainly process technologies in the nuclear fission method, fabrication and condition for irradiation of targets, transport and dissolution of targets irradiated, separation and purification of Mo-99, etc. Especially, for Mo-99 separation and purification process, the characteristics, merits and demerits of various processes, which have been developed in a few countries, were examined and analyzed. 30 figs., 16 tabs., 60 refs. (Author).

  4. Highly flexible, conductive and transparent MoO3/Ag/MoO3 multilayer electrode for organic photovoltaic cells

    International Nuclear Information System (INIS)

    Abachi, T.; Cattin, L.; Louarn, G.; Lare, Y.; Bou, A.; Makha, M.; Torchio, P.

    2013-01-01

    MoO 3 /Ag/MoO 3 (MAM) multilayer structures were deposited by vacuum evaporation on polyethylene terephthalate (PET) substrate. We demonstrate that, as in the case of glass substrate, the sheet resistance of such structures depends significantly on the Ag film deposition rate. When it is deposited between 0.2 and 0.4 nm/s, an Ag thickness of 11 nm allows achieving sheet resistance of 13 Ω/sq and an averaged transmission of 74%. A study of the influence of the PET substrate on the optimum MoO 3 thicknesses was done. A good qualitative agreement between the theoretical calculations of the variation of the optical transmittance of the MoO 3 /Ag/MoO 3 structures is obtained. The optimum MAM structures MoO 3 (17.5 nm)/Ag (11 nm)/MoO 3 (35 nm) has a factor of merit F M = 4.21 10 −3 (Ω/sq) −1 . Proven by the scotch test the MAM structures exhibit a good adhesion to the PET substrates. The MAM structures were also submitted to bending tests. For outer bending, the samples exhibit no variation of their resistance value, while for inner bending there is a small increase of the resistance of the MAM structures. However this increasing is smaller than that exhibited by Indium Tin Oxide. When the PET/MAM structures are used as anode in organic photovoltaic cells, it is shown that the need to use thicker Ag films inside the multilayer and to cover the MAM with Au to obtain promising Current density vs Voltage characteristics is due to the heating of the PET substrate during the deposition process. - Highlights: • MoO 3 /Ag/MoO 3 structures deposited on polyethylene terephthalate substrate. • MoO 3 /Ag/MoO 3 structures deposited by vacuum evaporation. • The Ag deposition rate influences the properties of the structures. • The MoO 3 /Ag/MoO 3 optimum structure has a factor of merit F M = 4.21 10 −3 (Ω/sq) −1 . • The MoO 3 /Ag/MoO 3 structures exhibit a high flexibility

  5. SYNTHESIS AND FABRICATION OF MO-W COMPONENTS FOR NEUTRON RESONANCE SPECTROSCOPY TEMPERATURE MEASUREMENT

    International Nuclear Information System (INIS)

    BINGERT, S.; DESCH, P.; TRUJILLO, E.

    1999-01-01

    A Molybdenum-- 182 Tungsten (Mo- 182 W) alloy was specified for an application that would ultimately result in the measurement of temperature and particle velocity during the steady state time following the shock loading of various materials. The 182 W isotope provides a tag for the analysis of neutron resonance line shape from which the temperature may be calculated. The material was specified to have 1.8 atom percent W, with W-rich regions no larger than 1 microm in size. Both the composition and W distribution were critical to the experiment. Another challenge to the processing was the very small quantity of 182 W material available for the synthesis of the alloy. Therefore, limited fabrication routes were available for evaluation. Several synthesis and processing routes were explored to fabricate the required alloy components. First, precipitation of W onto Mo powder using ammonium metatungstate was investigated for powder synthesis followed by uniaxial hot pressing. Second, mechanical alloying (MA) followed by hot isostatic pressing (HIP) and warm forging was attempted. Finally, arc-melting techniques followed by either hot rolling or crushing the alloyed button into powder and consolidation were pursued. The results of the processing routes and characterization of the materials produced will be discussed

  6. Antidepressants and Weight Gain

    Science.gov (United States)

    ... 2015;37:46. Blumenthal SR, et al. An electronic health records study of long-term weight gain following antidepressant ... your agreement to the Terms and Conditions and Privacy Policy linked below. Terms and Conditions Privacy Policy ...

  7. Weight gain - unintentional

    Science.gov (United States)

    ... diabetes Hormone changes or medical problems can also cause unintentional weight gain. This may be due to: Cushing syndrome Underactive thyroid, or low thyroid (hypothyroidism) Polycystic ovary syndrome Menopause Pregnancy Bloating, or swelling ...

  8. Weight and psychiatry

    African Journals Online (AJOL)

    Adele

    Beyond the physical aspects of weight, the psychological mean- ing sees the virtues of ... sion in the development and persistence of adolescent obesity. Pediat- rics 2002 ... or secondary as in mood, anxiety or psychotic disorders. II. a related.

  9. birth-weight infants

    African Journals Online (AJOL)

    including the CRIB (Clinical Risk Index for Babies) score, in a local ... these babies for expensive tertiary care. Subjects. ... patient numbers, the tendency is simply to increase the ... included birth weight, gestational age, 5-minute Apgar score ...

  10. Weight loss and alcohol

    Science.gov (United States)

    ... Maclean JC. Alcohol consumption and body weight. Health Econ . 2010;19(7):814-832. PMID: 19548203 www. ... member of Hi-Ethics and subscribes to the principles of the Health on the Net Foundation (www. ...

  11. Development and Cross-Validation of Equation for Estimating Percent Body Fat of Korean Adults According to Body Mass Index

    Directory of Open Access Journals (Sweden)

    Hoyong Sung

    2017-06-01

    Full Text Available Background : Using BMI as an independent variable is the easiest way to estimate percent body fat. Thus far, few studies have investigated the development and cross-validation of an equation for estimating the percent body fat of Korean adults according to the BMI. The goals of this study were the development and cross-validation of an equation for estimating the percent fat of representative Korean adults using the BMI. Methods : Samples were obtained from the Korea National Health and Nutrition Examination Survey between 2008 and 2011. The samples from 2008-2009 and 2010-2011 were labeled as the validation group (n=10,624 and the cross-validation group (n=8,291, respectively. The percent fat was measured using dual-energy X-ray absorptiometry, and the body mass index, gender, and age were included as independent variables to estimate the measured percent fat. The coefficient of determination (R², standard error of estimation (SEE, and total error (TE were calculated to examine the accuracy of the developed equation. Results : The cross-validated R² was 0.731 for Model 1 and 0.735 for Model 2. The SEE was 3.978 for Model 1 and 3.951 for Model 2. The equations developed in this study are more accurate for estimating percent fat of the cross-validation group than those previously published by other researchers. Conclusion : The newly developed equations are comparatively accurate for the estimation of the percent fat of Korean adults.

  12. Hydrothermal Synthesis of MoO2 and Supported MoO2 Cata-lysts for Oxidative Desulfurization of Dibenzothiophene

    Institute of Scientific and Technical Information of China (English)

    Wang Danhong; Zhang Jianyong; Liu Ni; Zhao Xin; Zhang Minghui

    2014-01-01

    A novel method for obtaining spherical MoO2 nanoparticles and SiO2-Al2O3 supported MoO2 by hydrothermal reduction of Mo (VI) species was studied. The obtained MoO2 catalysts show very high catalytic activity in the oxidative desulfurization (ODS) process. The effect of hydrothermal temperature and crystallization temperature on ODS activity was investigated. The ODS activity of supported MoO2 catalysts with various MoO2 contents were also investigated. The mecha-nism for formation of MoO2 involving oxalic acid was proposed.

  13. In search of zero thermal expansion anisotropy in Mo{sub 5}Si{sub 3} by strategic alloying

    Energy Technology Data Exchange (ETDEWEB)

    Dharmawardhana, C.C., E-mail: ccdxz8@mail.umkc.edu; Sakidja, R., E-mail: sakidjar@umkc.edu; Aryal, S.; Ching, W.Y.

    2015-01-25

    Highlights: • For the first time, theoretical prediction of achieving isotropic thermal expansion anisotropy (TEA) for T1 phase Mo{sub 5}Si{sub 3} by alloying with a mere 17.5% Al substitution on the Si sites. Most effective alloying proposed for the said system up to date. • The theoretical approach is verified by simulating the experimentally observed unusual TEA behaviour for (Mo,V){sub 5}Si{sub 3} alloys as a function of percent alloying. • The 2nd order and 3rd order elastic constants we explain the origin of the TEA in T1 phase for Mo{sub 5}Si{sub 3} system and how Al effect in reducing the TEA. • We use directional dependent phonon density of state, a novel approach, to identify the origin of the anisotropy and show this method of analysis could be used for other intermetallic alloys as well. - Abstract: Reducing the thermal expansion anisotropy (TEA) of alloy compounds is one of the most important issues for their potential applications in high temperature environment. The Mo{sub 5}Si{sub 3} (T1 phase) is known to be an important intermetallic compound with high melting temperature. Unfortunately, its large TEA renders it unsuitable for high temperature structural/coating applications. Many attempts have been made in the past to reduce TEA by substituting Mo by other transition metal ions such as V with little success and some unexpected observations. Here we use accurate ab initio molecular dynamics (AIMD) simulations to obtain the TEA from thermal expansion coefficients for two T1 phase alloy systems (Mo,V){sub 5}Si{sub 3} and Mo{sub 5}(Si,Al){sub 3}. We demonstrate that strategic alloying with Al substituting Si can achieve zero TEA for T1 phase. The microscopic origin of this outstanding thermomechanical properties in this alloy is explained by the calculation of higher order elastic constants in conjunction with atom and direction-resolved phonon density of states.

  14. ¿Cómo salir del liberalismo?

    Directory of Open Access Journals (Sweden)

    Lenin Flórez

    2001-01-01

    Full Text Available Alain Touraine ¿Cómo salir del Liberalismo? Piadós, Bacelona, 1999, 123 páginas. El libro parece circunscribirse al actual contexto político de Francia, que el autor considera como una coyuntura de salida del liberalismo. Su tema central gira alrededor de entender la democracia en este periodo y un proyecto político de más largo alcance. Sin embargo, sabemos que tiene serias investigaciones sobre la realidad latinoamericana, lo que nos indica que su temática rebasa el mundo europeo. Sin duda, el texto que reseñamos tiene un carácter crítico y sus planteamientos suscitan la controversia teórica.

  15. The Mo/Ta (100) interface

    International Nuclear Information System (INIS)

    Quintanar, C.; Velasco, V.R.; Garcia-Moliner, F.

    1990-12-01

    We have calculated the interface local density of states (ILDOS) formed by the transition metals Mo/Ta using a tight-binding Slater-Koster description and the Green Function matching method together with quickly converging algorithms to compute the transfer matrices. We obtain the surface LDOS as a byproduct. Our result is a useful tool to analyze experimental results and to check models as a function of the value of the tight-binding parameters either of the bulk or at the interface itself. We consider the (100) direction. We compare the interface to the bulk and to the surface and comment on some recently found experimental results for this interface. (author). 17 refs, 2 figs

  16. Chemical sensitivity of Mo gate Mos capacitors

    Energy Technology Data Exchange (ETDEWEB)

    Lombardi, R.M.; Aragon, R. [Laboratorio de Peliculas delgadas, Facultad de Ingenieria, Paseo Colon 850, 1063, Buenos Aires (Argentina)

    2006-07-01

    Mo gate Mos capacitors exhibit a negative shift of their C-V characteristic by up to 240 mV, at 125 C, in response to 1000 ppm hydrogen, in controlled nitrogen atmospheres. The experimental methods for obtaining capacitance and conductance, as a function of polarisation voltage, as well as the relevant equivalent circuits are reviewed. The single-state interface state density, at the semiconductor-dielectric interface, decreases from 2.66 x 10{sup 11} cm{sup -2} e-v{sup -1}, in pure nitrogen, to 2.5 x 10{sup 11} cm{sup -2} e-v{sup -1} in 1000 ppm hydrogen in nitrogen mixtures, at this temperature. (Author)

  17. Plasmons on the edge of MoS2 nanostructures

    DEFF Research Database (Denmark)

    Andersen, Kirsten; Jacobsen, Karsten Wedel; Thygesen, Kristian Sommer

    2014-01-01

    Using ab initio calculations we predict the existence of one-dimensional (1D), atomically confined plasmons at the edges of a zigzag MoS2 nanoribbon. The strongest plasmon originates from a metallic edge state localized on the sulfur dimers decorating the Mo edge of the ribbon. A detailed analysis...... of the dielectric function reveals that the observed deviations from the ideal 1D plasmon behavior result from single-particle transitions between the metallic edge state and the valence and conduction bands of the MoS2 sheet. The Mo and S edges of the ribbon are clearly distinguishable in calculated spatially...... resolved electron energy loss spectrum owing to the different plasmonic properties of the two edges. The edge plasmons could potentially be utilized for tuning the photocatalytic activity of MoS2 nanoparticles....

  18. Phase transformation in a Ni-Mo-Cr alloy

    International Nuclear Information System (INIS)

    Dymek, S.; Wrobel, M.; Blicharski, M.; Dollar, M.

    2001-01-01

    The paper gives a characteristic of a nickel-based superalloy containing 25 wt.% Mo and 8 wt.% Cr with particular attention to the influence of a thermochemical and heat treatment on phase transformations. The applied heat treatments are comprised of soaking temperature 1100 o C followed by aging at 650 o C at three conditions: conventional aging for 72 hours, prolonged aging for 4000 hours and prolonged aging for 4000 hours followed by cold working and subsequent aging for 1000 hours. The conventional aging led to the formation of lenticular precipitates of the dispersed metastable Ni 2 (Mo,Cr) phase. The aging for 4000 hours brought about coarsening of the ordered domains without changing their crystallographic and ordering characteristics. The plastic deformation preceded the further aging for 1000 hours accelerated the decomposition of the Ni 2 (Mo,Cr) phase on the mixture of the Ni 3 Mo and Ni 4 Mo-based phases. (author)

  19. Fission induced swelling of U–Mo/Al dispersion fuel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yeon Soo, E-mail: yskim@anl.gov [Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Jeong, G.Y. [Ulsan National Institute of Science and Technology, 50 UNIST-gil, Eonyang-eup, Uljoo-gun, Ulsan 689-798 (Korea, Republic of); Park, J.M. [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong-gu, Daejeon 305-353 (Korea, Republic of); Robinson, A.B. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-6188 (United States)

    2015-10-15

    Fission-induced swelling of U–Mo/Al dispersion fuel meat was measured using microscopy images obtained from post-irradiation examination. The data of reduced-size plate-type test samples and rod-type test samples were employed for this work. A model to predict the meat swelling of U–Mo/Al dispersion fuel was developed. This model is composed of several submodels including a model for interaction layer (IL) growth between U–Mo and Al matrix, a model for IL thickness to IL volume conversion, a correlation for the fission-induced swelling of U–Mo alloy particles, a correlation for the fission-induced swelling of IL, and models of U–Mo and Al consumption by IL growth. The model was validated using full-size plate data that were not included in the model development.

  20. Signatures of Low-Mo Ancient Ocean May be Preserved in Cyanobacterial Genomes

    Science.gov (United States)

    Glass, J. B.; Wolfe-Simon, F. L.; Poret-Peterson, A. T.; Anbar, A. D.

    2010-04-01

    Before 800 million years ago, Mo was scarce in the ocean. We present evidence that primitive cyanobacteria store Mo using a protein called "Mop." Mop genes preserved in modern genomes may be signatures of the imprint of ancient Mo limitation.

  1. Rocking disc electro-deposition of copper films on Mo/MoSe{sub 2} substrates

    Energy Technology Data Exchange (ETDEWEB)

    Cummings, Charles Y.; Frith, Paul E. [Department of Chemistry, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Zoppi, Guillaume; Forbes, Ian [Northumbria Photovoltaics Applications Centre, Northumbria University, NE1 8ST (United Kingdom); Rogers, Keith D. [Cranfield Health, Cranfield University, Shrivenham Campus, Swindon, SN6 8LA (United Kingdom); Lane, David W. [Department of Applied Science, Security and Resilience, Cranfield University, Shrivenham, Swindon, SN6 8LA (United Kingdom); Marken, Frank, E-mail: F.Marken@bath.ac.uk [Department of Chemistry, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom)

    2011-08-31

    A novel electro-deposition method based on a rocking disc system with {pi}/3 amplitude and variable frequency is introduced. Uniform copper films were deposited from a 0.1 M CuSO{sub 4}/3.0 M NaOH/0.2 M sorbitol bath directly onto 12.1 cm{sup 2} Mo/MoSe{sub 2} substrates with X-ray diffraction showing a thickness variation of {+-}5% over this area. Investigation of the mass transport conditions suggests (i) uniform diffusion over the sample, (ii) a rate of mass transport proportional to the square root of the rocking rate, and (iii) turbulent conditions, which are able to dislodge gas bubbles during electro-deposition.

  2. Determination of Mo- and Ca-isotope ratios in Ca100MoO4 crystal for AMoRE-I experiment

    Science.gov (United States)

    Karki, S.; Aryal, P.; Kim, H. J.; Kim, Y. D.; Park, H. K.

    2018-01-01

    The first phase of the AMoRE (Advanced Mo-based Rare process Experiment) is to search for neutrinoless double-beta decay of 100Mo with calcium molybdate (Ca100MoO4) crystals enriched in 100Mo and depleted in 48Ca using a cryogenic technique at Yangyang underground laboratory in Korea. It is important to know 100Mo- and 48Ca-isotope ratios in Ca100MoO4 crystal to estimate half-life of 100Mo decays and to 2 νββ background from 48Ca. We employed the ICP-MS (Inductive Coupled Plasma Mass Spectrometer) to measure 100Mo- and 48Ca-isotope ratios in Ca100MoO4 crystal. The measured results for 100Mo- and 48Ca-isotope ratios in the crystal are (94 . 6 ± 2 . 8) % and (0 . 00211 ± 0 . 00006) %, respectively, where errors are included both statistical and systematic uncertainties.

  3. Intercalation of Si between MoS2 layers

    Directory of Open Access Journals (Sweden)

    Rik van Bremen

    2017-09-01

    Full Text Available We report a combined experimental and theoretical study of the growth of sub-monolayer amounts of silicon (Si on molybdenum disulfide (MoS2. At room temperature and low deposition rates we have found compelling evidence that the deposited Si atoms intercalate between the MoS2 layers. Our evidence relies on several experimental observations: (1 Upon the deposition of Si on pristine MoS2 the morphology of the surface transforms from a smooth surface to a hill-and-valley surface. The lattice constant of the hill-and-valley structure amounts to 3.16 Å, which is exactly the lattice constant of pristine MoS2. (2 The transitions from hills to valleys are not abrupt, as one would expect for epitaxial islands growing on-top of a substrate, but very gradual. (3 I(V scanning tunneling spectroscopy spectra recorded at the hills and valleys reveal no noteworthy differences. (4 Spatial maps of dI/dz reveal that the surface exhibits a uniform work function and a lattice constant of 3.16 Å. (5 X-ray photo-electron spectroscopy measurements reveal that sputtering of the MoS2/Si substrate does not lead to a decrease, but an increase of the relative Si signal. Based on these experimental observations we have to conclude that deposited Si atoms do not reside on the MoS2 surface, but rather intercalate between the MoS2 layers. Our conclusion that Si intercalates upon the deposition on MoS2 is at variance with the interpretation by Chiappe et al. (Adv. Mater. 2014, 26, 2096–2101 that silicon forms a highly strained epitaxial layer on MoS2. Finally, density functional theory calculations indicate that silicene clusters encapsulated by MoS2 are stable.

  4. Final report of MoReMO 2011-2012. Modelling resilience for maintenance and outage

    International Nuclear Information System (INIS)

    Gotcheva, N.; Macchi, L.; Oedewald, P.; Eitrheim, M.H.R.; Axelsson, C.; Reiman, T.; Pietikaeinen, E.

    2013-04-01

    The project Modelling Resilience for Maintenance and Outage (MoReMO) represents a two-year joint effort by VTT Technical Research Centre of Finland, Institute for Energy Technology (IFE, Norway) and Vattenfall (Sweden) to develop and test new approaches for safety management. The overall goal of the project was to present concepts on how resilience can be operationalized and built in a safety critical and socio-technical context. Furthermore, the project also aimed at providing guidance for other organizations that strive to develop and improve their safety performance in a business driven industry. We have applied four approaches in different case studies: Organisational Core Task modelling (OCT), Functional Resonance Analysis Method (FRAM), Efficiency Thoroughness Trade-Off (ETTO) analysis, and Work Practice and Culture Characterisation. During 2011 and 2012 the MoReMO project team has collected data through field observations, interviews, workshops, and document analysis on the work practices and adjustments in maintenance and outage in Nordic NPPs. The project consisted of two sub-studies, one focused on identifying and assessing adjustments and supporting resilient work practices in maintenance activities, while the other focused on handling performance trade-offs in maintenance and outage, as follows: A. Adjustments in maintenance work in Nordic nuclear power plants (VTT and Vattenfall). B. Handling performance trade-offs - the support of adaptive capacities (IFE and Vattenfall). The historical perspective of maintenance and outage management (Chapter 1.1) was provided by Vattenfall. Together, the two sub-studies have provided valuable insights for understanding the rationale behind work practices and adjustments, their effects on resilience, promoting flexibility and balancing between flexibility and reliability. (Author)

  5. Final report of MoReMO 2011-2012. Modelling resilience for maintenance and outage

    Energy Technology Data Exchange (ETDEWEB)

    Gotcheva, N.; Macchi, L.; Oedewald, P. [Technical Research Centre of Finland (VTT), Espoo (Finland); Eitrheim, M.H.R. [Institute for Energy Technology (IFE) (Norway); Axelsson, C.; Reiman, T.; Pietikaeinen, E. [Ringhals AB (NPP), Vattenfall AB (Sweden)

    2013-04-15

    The project Modelling Resilience for Maintenance and Outage (MoReMO) represents a two-year joint effort by VTT Technical Research Centre of Finland, Institute for Energy Technology (IFE, Norway) and Vattenfall (Sweden) to develop and test new approaches for safety management. The overall goal of the project was to present concepts on how resilience can be operationalized and built in a safety critical and socio-technical context. Furthermore, the project also aimed at providing guidance for other organizations that strive to develop and improve their safety performance in a business driven industry. We have applied four approaches in different case studies: Organisational Core Task modelling (OCT), Functional Resonance Analysis Method (FRAM), Efficiency Thoroughness Trade-Off (ETTO) analysis, and Work Practice and Culture Characterisation. During 2011 and 2012 the MoReMO project team has collected data through field observations, interviews, workshops, and document analysis on the work practices and adjustments in maintenance and outage in Nordic NPPs. The project consisted of two sub-studies, one focused on identifying and assessing adjustments and supporting resilient work practices in maintenance activities, while the other focused on handling performance trade-offs in maintenance and outage, as follows: A. Adjustments in maintenance work in Nordic nuclear power plants (VTT and Vattenfall). B. Handling performance trade-offs - the support of adaptive capacities (IFE and Vattenfall). The historical perspective of maintenance and outage management (Chapter 1.1) was provided by Vattenfall. Together, the two sub-studies have provided valuable insights for understanding the rationale behind work practices and adjustments, their effects on resilience, promoting flexibility and balancing between flexibility and reliability. (Author)

  6. Diet induced weight loss accelerates onset of negative alliesthesia in obese women

    Directory of Open Access Journals (Sweden)

    Frankham Patrick

    2005-10-01

    Full Text Available Abstract Background The physiological and behavioral responses to hypocaloric diet are to increase energy intake to defend a steady body weight. We utilized the method of "negative alliesthesia" for measuring the hedonic reponse to sweet stimulus before (Initial session and 3 months after entering a weight loss program. The negative alliesthesia test is known by physiologists but few clinical data exist. It is based on the observation that repeated pleasant gustatory stimuli turn into unpleasantness in the process of alliesthesia. At first visit participants repeatedly ingested sweet stimuli until they found them unpleasant and rated quantitatively on a linear analogue scale their hedonic experience. This procedure was repeated every 3 min until participants felt displeasure to end the session. The same protocol was followed after three months of following a weight loss diet. Dieting energy intake was from 1400 – 2000 kcal/d for 8 wk. Energy composition was 50% carb:25% prot: 25% lipid. After 8 wk caloric intake increased by 50 kcal/wk, to reach daily intake of 1800 – 2400 kcal/d. Energy composition was 50% carb:22% prot: 27% lipid. We report results on the effect of slow weight loss on negative alliesthesia in ten obese female participants enrolled in a commercial diet program based on Canada's Food Guide (Mincavi®. Results Results showed that diet lowered the mean BMI (Initial session 36.8 +/- 1.8 vs. 3 mo 34.9 +/- 1.8 kg/m2. At 3 mo the onset of negative alliesthesia, time to abandon experimental session, was shortened (Initial session 33 vs. 3 mo 24 min. The same trend was observed in the time to reach indifference (Initial session 21.9 +/- 3.8 vs. 3 mo 16.2 +/-2.4 min. There was no observed difference in maximum (Initial session +79.5 +/- 11.7; 3 mo +94.5 +/- 9.9 mm and minimum (Initial session -90.0 +/- 14.4; 3 mo -106 +/- 11.1 mm hedonic rating. Conclusion Earlier onset of negative alliesthesia, as seen in our participants, is not

  7. Benchmark experiment for the cross section of the 100Mo(p,2n)99mTc and 100Mo(p,pn)99Mo reactions

    Science.gov (United States)

    Takács, S.; Ditrói, F.; Aikawa, M.; Haba, H.; Otuka, N.

    2016-05-01

    As nuclear medicine community has shown an increasing interest in accelerator produced 99mTc radionuclide, the possible alternative direct production routes for producing 99mTc were investigated intensively. One of these accelerator production routes is based on the 100Mo(p,2n)99mTc reaction. The cross section of this nuclear reaction was studied by several laboratories earlier but the available data-sets are not in good agreement. For large scale accelerator production of 99mTc based on the 100Mo(p,2n)99mTc reaction, a well-defined excitation function is required to optimise the production process effectively. One of our recent publications pointed out that most of the available experimental excitation functions for the 100Mo(p,2n)99mTc reaction have the same general shape while their amplitudes are different. To confirm the proper amplitude of the excitation function, results of three independent experiments were presented (Takács et al., 2015). In this work we present results of a thick target count rate measurement of the Eγ = 140.5 keV gamma-line from molybdenum irradiated by Ep = 17.9 MeV proton beam, as an integral benchmark experiment, to prove the cross section data reported for the 100Mo(p,2n)99mTc and 100Mo(p,pn)99Mo reactions in Takács et al. (2015).

  8. Carbon and Mo transformations during the synthesis of mesoporous Mo2C/carbon catalysts by carbothermal hydrogen reduction

    Science.gov (United States)

    Wang, Haiyan; Liu, Shida; Liu, Bing; Montes, Vicente; Hill, Josephine M.; Smith, Kevin J.

    2018-02-01

    The synthesis of mesoporous Mo2C/carbon catalysts by carbothermal hydrogen reduction is reported. Petroleum coke (petcoke) was activated with KOH at 800 °C to obtain high surface area microporous activated petcoke (APC; 2000 m2/g). The APC was wet impregnated with ammonium heptamolybdate (AHM: 10 wt% Mo), dried and reduced in H2 at temperatures from 400 to 800 °C, to yield Mo2C/APC catalysts. Increased reduction temperature increased the Mo2C yield and the mesoporous volume of the Mo2C/APC. At a reduction temperature of 750 °C the mesopore volume of the catalyst doubled compared to the APC support and accounted for 37% of the total pore volume. Maintaining the final CHR temperature for 90 min further increased the Mo2C yield and mesoporosity of the catalyst. The role of Mo2C in the catalytic hydrogenation of the APC and mesopore generation is demonstrated. The activity of the Mo2C/carbon catalysts in the hydrodeoxygenation of 4-methyl phenol increased with increased CHR temperature and catalyst mesoporosity.

  9. Theoretical prediction of high electron mobility in multilayer MoS2 heterostructured with MoSe2

    Science.gov (United States)

    Ji, Liping; Shi, Juan; Zhang, Z. Y.; Wang, Jun; Zhang, Jiachi; Tao, Chunlan; Cao, Haining

    2018-01-01

    Two-dimensional (2D) MoS2 has been considered to be one of the most promising semiconducting materials with the potential to be used in novel nanoelectronic devices. High carrier mobility in the semiconductor is necessary to guarantee a low power dissipation and a high switch speed of the corresponding electronic device. Strain engineering in 2D materials acts as an important approach to tailor and design their electronic and carrier transport properties. In this work, strain is introduced to MoS2 through perpendicularly building van der Waals heterostructures MoSe2-MoS2. Our first-principles calculations demonstrate that acoustic-phonon-limited electron mobility can be significantly enhanced in the heterostructures compared with that in pure multilayer MoS2. It is found that the effective electron mass and the deformation potential constant are relatively smaller in the heterostructures, which is responsible for the enhancement in the electron mobility. Overall, the electron mobility in the heterostructures is about 1.5 times or more of that in pure multilayer MoS2 with the same number of layers for the studied structures. These results indicate that MoSe2 is an excellent material to be heterostructured with multilayer MoS2 to improve the charge transport property.

  10. Coke formation during the hydrotreatment of bio-oil using NiMo and CoMo catalysts

    NARCIS (Netherlands)

    Kadarwati, Sri; Hu, Xun; Gunawan, Richard; Westerhof, Roel; Gholizadeh, Mortaza; Hasan, M. D.Mahmudul; Li, Chun-Zhu

    2017-01-01

    This study aims to investigate the coke formation during the hydrotreatment of bio-oil at low temperature. The catalytic hydrotreatment of bio-oil produced from the pyrolysis of mallee wood was carried out using pre-sulphided NiMo and CoMo catalysts at a temperature range of 150–300 °C. Our results

  11. Relationships between consumption of ultra-processed foods, gestational weight gain and neonatal outcomes in a sample of US pregnant women

    Directory of Open Access Journals (Sweden)

    Karthik W. Rohatgi

    2017-12-01

    Full Text Available Background An increasingly large share of diet comes from ultra-processed foods (UPFs, which are assemblages of food substances designed to create durable, convenient and palatable ready-to-eat products. There is increasing evidence that high UPF consumption is indicative of poor diet and is associated with obesity and metabolic disorders. This study sought to examine the relationship between percent of energy intake from ultra-processed foods (PEI-UPF during pregnancy and maternal gestational weight gain, maternal lipids and glycemia, and neonatal body composition. We also compared the PEI-UPF indicator against the US government’s Healthy Eating Index-2010 (HEI-2010. Methods Data were used from a longitudinal study performed in 2013–2014 at the Women’s Health Center and Obstetrics & Gynecology Clinic in St. Louis, MO, USA. Subjects were pregnant women in the normal and obese weight ranges, as well as their newborns (n = 45. PEI-UPF and the Healthy Eating Index-2010 (HEI-2010 were calculated for each subject from a one-month food frequency questionnaire (FFQ. Multiple regression (ANCOVA-like analysis was used to analyze the relationship between PEI-UPF or HEI-2010 and various clinical outcomes. The ability of these dietary indices to predict clinical outcomes was also compared with the predictive abilities of total energy intake and total fat intake. Results An average of 54.4 ± 13.2% of energy intake was derived from UPFs. A 1%-point increase in PEI-UPF was associated with a 1.33 kg increase in gestational weight gain (p = 0.016. Similarly, a 1%-point increase in PEI-UPF was associated with a 0.22 mm increase in thigh skinfold (p = 0.045, 0.14 mm in subscapular skinfold (p = 0.026, and 0.62 percentage points of total body adiposity (p = 0.037 in the neonate. Discussion PEI-UPF (percent of energy intake from ultra-processed foods was associated with and may be a useful predictor of increased gestational weight gain and neonatal

  12. Asymptomatic endemic Chlamydia pecorum infections reduce growth rates in calves by up to 48 percent.

    Directory of Open Access Journals (Sweden)

    Anil Poudel

    Full Text Available Intracellular Chlamydia (C. bacteria cause in cattle some acute but rare diseases such as abortion, sporadic bovine encephalomyelitis, kerato-conjunctivitis, pneumonia, enteritis and polyarthritis. More frequent, essentially ubiquitous worldwide, are low-level, asymptomatic chlamydial infections in cattle. We investigated the impact of these naturally acquired infections in a cohort of 51 female Holstein and Jersey calves from birth to 15 weeks of age. In biweekly sampling, we measured blood/plasma markers of health and infection and analyzed their association with clinical appearance and growth in dependence of chlamydial infection intensity as determined by mucosal chlamydial burden or contemporaneous anti-chlamydial plasma IgM. Chlamydia 23S rRNA gene PCR and ompA genotyping identified only C. pecorum (strains 1710S, Maeda, and novel strain Smith3v8 in conjunctival and vaginal swabs. All calves acquired the infection but remained clinically asymptomatic. High chlamydial infection associated with reduction of body weight gains by up to 48% and increased conjunctival reddening (P<10(-4. Simultaneously decreased plasma albumin and increased globulin (P<10(-4 suggested liver injury by inflammatory mediators as mechanisms for the growth inhibition. This was confirmed by the reduction of plasma insulin like growth factor-1 at high chlamydial infection intensity (P<10(-4. High anti-C. pecorum IgM associated eight weeks later with 66% increased growth (P = 0.027, indicating a potential for immune protection from C. pecorum-mediated growth depression. The worldwide prevalence of chlamydiae in livestock and their high susceptibility to common feed-additive antibiotics suggests the possibility that suppression of chlamydial infections may be a major contributor to the growth promoting effect of feed-additive antibiotics.

  13. A weight-loss program adapted to the menstrual cycle increases weight loss in healthy, overweight, premenopausal women

    DEFF Research Database (Denmark)

    Geiker, Nina R W; Ritz, Christian; Pedersen, Sue D

    2016-01-01

    compared with the effect of simple energy restriction. DESIGN: A total of 60 healthy, overweight, premenopausal women were included in a 6-mo weight-loss program in which each subject consumed a diet of 1600 kcal/d. Subjects were randomly assigned to either a combined diet and exercise program...... that was tailored to metabolic changes of the menstrual cycle (Menstralean) or to undergo simple energy restriction (control). RESULTS: Thirty-one women (19 Menstralean and 12 control women) completed the study [mean ± SD body mass index (in kg/m(2)): 32.0 ± 5.2]. Both groups lost weight during the study....... CONCLUSION: A differentiated diet and exercise program that is tailored to counteract food cravings and metabolic changes throughout the menstrual cycle may increase weight loss above that achieved with a traditional diet and exercise program in women who can comply with the program. This trial...

  14. Weight Loss Nutritional Supplements

    Science.gov (United States)

    Eckerson, Joan M.

    Obesity has reached what may be considered epidemic proportions in the United States, not only for adults but for children. Because of the medical implications and health care costs associated with obesity, as well as the negative social and psychological impacts, many individuals turn to nonprescription nutritional weight loss supplements hoping for a quick fix, and the weight loss industry has responded by offering a variety of products that generates billions of dollars each year in sales. Most nutritional weight loss supplements are purported to work by increasing energy expenditure, modulating carbohydrate or fat metabolism, increasing satiety, inducing diuresis, or blocking fat absorption. To review the literally hundreds of nutritional weight loss supplements available on the market today is well beyond the scope of this chapter. Therefore, several of the most commonly used supplements were selected for critical review, and practical recommendations are provided based on the findings of well controlled, randomized clinical trials that examined their efficacy. In most cases, the nutritional supplements reviewed either elicited no meaningful effect or resulted in changes in body weight and composition that are similar to what occurs through a restricted diet and exercise program. Although there is some evidence to suggest that herbal forms of ephedrine, such as ma huang, combined with caffeine or caffeine and aspirin (i.e., ECA stack) is effective for inducing moderate weight loss in overweight adults, because of the recent ban on ephedra manufacturers must now use ephedra-free ingredients, such as bitter orange, which do not appear to be as effective. The dietary fiber, glucomannan, also appears to hold some promise as a possible treatment for weight loss, but other related forms of dietary fiber, including guar gum and psyllium, are ineffective.

  15. Studies of the effect of irradiation in a nuclear reactor, of targets containing Mo used for the preparation of 99Mo gel, material that constitutes the 99Mo - 99mTc generators

    International Nuclear Information System (INIS)

    Nieto, Renata Correa

    2004-01-01

    The most used radioisotope in Nuclear Medicine is 99m Tc, obtained in the 99 Mo - 99m Tc generator form. 99 Mo can be produced by several nuclear reactions in Cyclotron and Reactor. The production in Cyclotron is not technically and commercially feasible. The production in Nuclear Reactor can be made in two ways: 235 U fission and 99 Mo (n,γ) 99 Mo reaction. A project aiming the production of 99 Mo by activation of Mo is under way at IPEN, producing a gel type MoZr generator. There are two ways of preparing the gel and the generators: by irradiating MoO 3 and preparing the gel or by the preparation of the gel and further irradiation. This work consists in the study of the irradiation effects in several targets containing Mo for the production of 99 Mo by the 98 Mo (n,γ) 99 Mo reaction and further preparation of the gel for use as a gel type 99 Mo - 99m Tc generator. Three rinds of gel were studied: zirconium, titanium and cerium molybdate, and their morphology, infrared structure and elution yield of 99m Tc were analysed. The best results were achieved with the generators prepared with MoZr post formed gel, with amorphous structure and better elution yields. The pre formed gel induced crystallinity and worst performance of the generators. (author)

  16. Geochronology of the Thompson Creek Mo Deposit: Evidence for the Formation of Arc-related Mo Deposits

    Science.gov (United States)

    Lawrence, C. D.; Coleman, D. S.; Stein, H. J.

    2016-12-01

    The Thompson Creek Mo deposit in central ID, has been categorized as an arc-related Mo deposit due to the location, grade of Mo, and relative lack of enrichments in F, Rb, and Nb, compared to the Climax-type Mo deposits. Geochronology from this arc-related deposit provides an opportunity to compare and contrast magmatism, and mineralization to that in Climax-type deposits. Distinct pulses of magmatism were required to form the Thompson Creek Mo deposit, which is consistent with recent geochronology from Climax-type deposits. Molybdenite Re-Os geochronology from five veins requires at least three pulses of magmatism and mineralization between 89.39 +/- 0.37 and 88.47 +/- 0.16 Ma. Zircon U-Pb ages from these mineralized samples overlap with molybdenite mineralization, but show a much wider range (91.01 +/- 0.37 to 87.27 +/- 0.69). Previous work from Climax-type Mo deposits suggest a correlation between a super eruption, and the subsequent rapid (<1 Ma) onset, and completion of Mo mineralizing intrusions. The longer life (3-4 Ma) for the Thompson Creek Mo deposit suggests that the mineralizing intrusions for arc-related Mo deposits may not need to have as high [Mo] as the Climax-type deposits. This study also finds a shift in the source of magmatism from the pre- to syn-mineralizing intrusions. Zircons from pre-mineralizing intrusions have much higher (15-60 pg) concentrations of radiogenic Pb than zircons from mineralized intrusions, which all have less than 15 pg, though whole rock [U] are similar.

  17. A model for growth of beta-phase particles in zirconium-2.5 wt percent niobium

    International Nuclear Information System (INIS)

    Chow, C.K.; Liner, Y.; Rigby, G.L.

    1984-08-01

    The kinetics of the α → β phase change in Zr-2.5 percent Nb pressure-tube material at constant temperature have been studied. The volume-fraction change of the β phase due to diffusion in an infinite α-phase matrix was considered, and a mathematical model with a numerical solution was developed to predict the transient spherical growth of the β-phase region. This model has been applied to Zr-2.5 wt percent Nb, and the calculated results compared to experiment

  18. Study of extraterrestrial disposal of radioactive wastes. Part 3: Preliminary feasibility screening study of space disposal of the actinide radioactive wastes with 1 percent and 0.1 percent fission product contamination

    Science.gov (United States)

    Hyland, R. E.; Wohl, M. L.; Finnegan, P. M.

    1973-01-01

    A preliminary study was conducted of the feasibility of space disposal of the actinide class of radioactive waste material. This waste was assumed to contain 1 and 0.1 percent residual fission products, since it may not be feasible to completely separate the actinides. The actinides are a small fraction of the total waste but they remain radioactive much longer than the other wastes and must be isolated from human encounter for tens of thousands of years. Results indicate that space disposal is promising but more study is required, particularly in the area of safety. The minimum cost of space transportation would increase the consumer electric utility bill by the order of 1 percent for earth escape and 3 percent for solar escape. The waste package in this phase of the study was designed for normal operating conditions only; the design of next phase of the study will include provisions for accident safety. The number of shuttle launches per year required to dispose of all U.S. generated actinide waste with 0.1 percent residual fission products varies between 3 and 15 in 1985 and between 25 and 110 by 2000. The lower values assume earth escape (solar orbit) and the higher values are for escape from the solar system.

  19. A novel three dimensional semimetallic MoS{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Zhen-Kun [Beijing Computational Science Research Center, Beijing 100084 (China); Departments of Physics and Electronics, Hengyang Normal University, Hengyang 421008 (China); Zhang, Hui; Liu, Li-Min, E-mail: limin.liu@csrc.ac.cn [Beijing Computational Science Research Center, Beijing 100084 (China); Liu, Hao [Chengdu Green Energy and Green Manufacturing Technology R and D Center, Chengdu, Sichuan 610207 (China); Lau, Woon-Ming [Beijing Computational Science Research Center, Beijing 100084 (China); Chengdu Green Energy and Green Manufacturing Technology R and D Center, Chengdu, Sichuan 610207 (China)

    2014-05-28

    Transition metal dichalcogenides (TMDs) have many potential applications, while the performances of TMDs are generally limited by the less surface active sites and the poor electron transport efficiency. Here, a novel three-dimensional (3D) structure of molybdenum disulfide (MoS{sub 2}) with larger surface area was proposed based on first-principle calculations. 3D layered MoS{sub 2} structure contains the basal surface and joint zone between the different nanoribbons, which is thermodynamically stable at room temperature, as confirmed by first principles molecular dynamics calculations. Compared the two-dimensional layered structures, the 3D MoS{sub 2} not only owns the large surface areas but also can effectively avoid the aggregation. Interestingly, although the basal surface remains the property of the intrinsic semiconductor as the bulk MoS{sub 2}, the joint zone of 3D MoS{sub 2} exhibits semimetallic, which is derived from degenerate 3d orbitals of the Mo atoms. The high stability, large surface area, and high conductivity make 3D MoS{sub 2} have great potentials as high performance catalyst.

  20. Using molybdenum depleted in 95Mo in UMo fuel

    International Nuclear Information System (INIS)

    Bakker, K.; Wijtsma, F.; Bos, A.; Mol, C.; Rakhorst, H.; Bretscher, M.; Hofman, G.; Snelgrove, J.

    2002-01-01

    In recent years significant interest was gained in UMo fuel to be used in Material Test Reactors. This interest was induced by the fact that UMo fuel is mechanically stable, even at high uranium concentrations and high U-burnup. These properties are required in order to use Low Enriched Uranium (LEU) and still be able to achieve high flux and burnup values and, thus, to facilitate the conversion from High Enriched Uranium (HEU) to LEU. Neutronics computations have shown that, although the Mo concentration in UMo fuel is not very high (about 5 - 10w%), the neutron absorption cross sections of natural Mo are sufficiently high to have a considerable negative impact on the reactivity of this UMo fuel. In the present research the neutron absorption cross sections of natural Mo are discussed and the option to reduce the cross section of molybdenum by depleting the Mo in 95 Mo is described. Finally the economic consequences of using Mo depleted in 95 Mo are briefly discussed

  1. Homogenization of compacted blends of Ni and Mo powders

    International Nuclear Information System (INIS)

    Lanam, R.D.; Yeh, F.C.H.; Rovsek, J.E.; Smith, D.W.; Heckel, R.W.

    1975-01-01

    The homogenization behavior of compacted blends of Ni and Mo powders was studied primarily as a function of temperature, mean compact composition, and Mo powder particle size. All compact compositions were in the Ni-rich terminal solid-solution range; temperatures were between 950 and 1200 0 C (in the region of the phase diagram where only the Mo--Ni intermediate phase forms); average Mo particle sizes ranged from 8.4 mu m to 48 mu m. Homogenization was characterized in terms of the rate of decrease of the amounts of the Mo-rich terminal solid-solution phase and the Mo--Ni intermediate phase. The experimental results were compared to predictions based upon the three-phase, concentric-sphere homogenization model. In general, agreement between experimental data and model predictions was fairly good for high-temperature treatments and for compact compositions which were not close to the solubility limit of Mo in Ni. Departures from the model are discussed in terms of surface diffusion contributions to homogenization and non-uniform mixing effects. (U.S.)

  2. Weight Management in Phenylketonuria

    DEFF Research Database (Denmark)

    Rocha, Julio César; van Rijn, Margreet; van Dam, Esther

    2016-01-01

    . It is becoming evident that in addition to acceptable blood phenylalanine control, metabolic dieticians should regard weight management as part of routine clinical practice. SUMMARY: It is important for practitioners to differentiate the 3 levels for overweight interpretation: anthropometry, body composition...... and frequency and severity of associated metabolic comorbidities. The main objectives of this review are to suggest proposals for the minimal standard and gold standard for the assessment of weight management in PKU. While the former aims to underline the importance of nutritional status evaluation in every...... specialized clinic, the second objective is important in establishing an understanding of the breadth of overweight and obesity in PKU in Europe. KEY MESSAGES: In PKU, the importance of adopting a European nutritional management strategy on weight management is highlighted in order to optimize long...

  3. Weight for Stephen Finlay.

    Science.gov (United States)

    Evers, Daan

    2013-04-01

    According to Stephen Finlay, ' A ought to X ' means that X -ing is more conducive to contextually salient ends than relevant alternatives. This in turn is analysed in terms of probability. I show why this theory of 'ought' is hard to square with a theory of a reason's weight which could explain why ' A ought to X ' logically entails that the balance of reasons favours that A X -es. I develop two theories of weight to illustrate my point. I first look at the prospects of a theory of weight based on expected utility theory. I then suggest a simpler theory. Although neither allows that ' A ought to X ' logically entails that the balance of reasons favours that A X -es, this price may be accepted. For there remains a strong pragmatic relation between these claims.

  4. Study of methodologies for quality control of 99Mo used in 99Mo/99mTc generators

    International Nuclear Information System (INIS)

    Said, Daphne de Souza

    2016-01-01

    99m Tc is the most used radionuclide in nuclear medicine. In Brazil, the 99 Mo/ 99m Tc generators are exclusively produced by Radiopharmacy Center at IPEN-CNEN/ SP, by importing 99 Mo from different suppliers. 99 Mo (t 1/2 = 66 h) is a fission product of 235 U and it can have radionuclidic impurities that are prejudicial for human health. For safe use of generators, it is necessary to perform the evaluation of 99 Mo by quality control tests in order to assess if 99 Mo complies with the specifications. The European Pharmacopoeia (EP) presents a monograph for evaluation of the quality of the [ 99 Mo] solution as sodium molybdate,that is used as raw material for 99 Mo/ 99m Tc generators production, including specification parameters (identification, radiochemical purity and radionuclidic purity), analysis methods and limits. However, it has been observed difficulties on the execution and implementation of these methods by the generators producers, with a few literature about this subject, probably due to complexity of the proposed methods. In this work, many quality control parameters of 99 Mo described in the EP monograph were evaluated. Separation methods for 99M o from its radionuclidic impurities by solid phase extraction (SPE) and TLC were studied. After SPE separation, the quantification of metals by ICP-OES to evaluate the percentage of retention of Mo and the percentage of recovery of Ru, Te and Sr using different types of cartridges were proposed, replacing radiotracers use. It was observed that the specific type of SPE cartridge recommended by the EP for separation of 99 Mo presented low recoveries for Ru, compared to other available anion exchange SPE cartridges. 99 Mo samples from different worldwide suppliers were analyzed. It was observed that quantification of 103 Ru in 99 Mo samples with decay time higher than 4 weeks is possible. An alternative method for separation of 131 I from 99 Mo showed promising results by TLC. The quantification of beta and

  5. Development of production of {sup 99}Mo from LEU target

    Energy Technology Data Exchange (ETDEWEB)

    Adang, H G; Mutalib, A; Lubis, H [Radioisotope Production Centre, National Atomic Energy Agency, Kawasan Puspiptek, Serpong (Indonesia); and others

    1998-10-01

    {sup 99}TC, the most popular radioisotope in nuclear medicine, is daughter of {sup 99}Mo. {sup 99}Mo is produced in research reactor by irradiating of high enriched uranium (HEU). However, in recent year, strict regulation that has been implemented by USA DOE and NPT has led to the difficulty in getting HEU. Therefore, BATAN has tried to develop the production of {sup 99}Mo by using low enriched uranium (LEU). The research involves the use of LEU in the production of {sup 99}Mo. This research was started in 1994 by joint-research between BATAN and Argonne National Laboratory USA. This program is divided into three research groups. The first group emphasizes its research on fabrication of LEU foil that is going to be irradiated. The second group studies the irradiation`s aspects and physical characteristic of irradiated LEU foils. The third group studies the radiochemical separation process of fission product {sup 99}Mo from solution of irradiated LEU foils. There are five steps that are carried out in studying of radiochemical separation of {sup 99}Mo from irradiated LEU. First is designing a dissolver that is going to be used in dissolving of LEU foil and testing its reliability. Second is dissolving LEU in the new design dissolver. Third is evaluation the modified of Cintichem`s radiochemical separation process of {sup 99}Mo from LEU. Forth is modifying the Cintichem`s radiochemical separation process of {sup 99}Mo from the solution of irradiated LEU. And fifth is using the modified of Cintichem`s radiochemical separation process for separation {sup 99}Mo from solution of irradiated LEU. The first through the forth steps of experiments were already carried out and will be reported in this workshop, whereas the fifth step of experiment is going to be conducted in February 1998. (author)

  6. Excitation functions of the 98Mo+d reactions

    International Nuclear Information System (INIS)

    Zarubin, P.P.; Padalko, V.Yu.; Khrisanfov, Yu.V.; Lebedev, P.P.; Podkopaev, Yu.N.

    The excitation functions of the 98 Mo+d reactions were studied. The energy dependence of (d,p),(d,n) and (d,α) reactions was investigated by the activation analysis. The energies of deuterons in the range (6-12) MeV were determined by means of the aluminium filters. 98 Mo foils with surface densities of 1.02, 0.23 and 0.14 mgxcm -2 with 98 Mo enrichment of 94.1% were used as targets. The gamma spectra were measured by a Ge(Li) detector. The 98 Mo(d,p) 99 Mo reaction excitation function was determined via detection of 739 and 181 keV γ-radiation of 99 Mo (Tsub(1/2)=66.47h); 140 keV γ-radiation of 99 Tc (Tsub(1/2)=6h) was detected for the 98 Mo(d,n) 99 Tc reaction excitation function determination and 460, 568, 1091, 1200 and 1492 keV γ-quanta of 96 Nb (Tsub(1/2)=23.35h) - for the 98 Mo(d,α) 96 Nb reaction. In the excitation function the wide extremum was observed at Esub(d) approximately 10 MeV. The ratio of cross sections σsup(m)(d,n)/σ(d,p) on the 98 Mo target was determined. The ratio σsup(m)(d,n)/σ(d,p) was found to be decreasing function of the deuteron energy. The relative cross sections were determined with an accuracy of +-5%, while for the absolute values of cross sections the accuracy was +-15%

  7. Dairy cow disability weights.

    Science.gov (United States)

    McConnel, Craig S; McNeil, Ashleigh A; Hadrich, Joleen C; Lombard, Jason E; Garry, Franklyn B; Heller, Jane

    2017-08-01

    Over the past 175 years, data related to human disease and death have progressed to a summary measure of population health, the Disability-Adjusted Life Year (DALY). As dairies have intensified there has been no equivalent measure of the impact of disease on the productive life and well-being of animals. The development of a disease-adjusted metric requires a consistent set of disability weights that reflect the relative severity of important diseases. The objective of this study was to use an international survey of dairy authorities to derive disability weights for primary disease categories recorded on dairies. National and international dairy health and management authorities were contacted through professional organizations, dairy industry publications and conferences, and industry contacts. Estimates of minimum, most likely, and maximum disability weights were derived for 12 common dairy cow diseases. Survey participants were asked to estimate the impact of each disease on overall health and milk production. Diseases were classified from 1 (minimal adverse effects) to 10 (death). The data was modelled using BetaPERT distributions to demonstrate the variation in these dynamic disease processes, and to identify the most likely aggregated disability weights for each disease classification. A single disability weight was assigned to each disease using the average of the combined medians for the minimum, most likely, and maximum severity scores. A total of 96 respondents provided estimates of disability weights. The final disability weight values resulted in the following order from least to most severe: retained placenta, diarrhea, ketosis, metritis, mastitis, milk fever, lame (hoof only), calving trauma, left displaced abomasum, pneumonia, musculoskeletal injury (leg, hip, back), and right displaced abomasum. The peaks of the probability density functions indicated that for certain disease states such as retained placenta there was a relatively narrow range of

  8. Savannah River Site Tank Cleaning: Corrosion Rate For One Versus Eight Percent Oxalic Acid Solution

    International Nuclear Information System (INIS)

    Ketusky, E.; Subramanian, K.

    2011-01-01

    Until recently, the use of oxalic acid for chemically cleaning the Savannah River Site (SRS) radioactive waste tanks focused on using concentrated 4 and 8-wt% solutions. Recent testing and research on applicable dissolution mechanisms have concluded that under appropriate conditions, dilute solutions of oxalic acid (i.e., 1-wt%) may be more effective. Based on the need to maximize cleaning effectiveness, coupled with the need to minimize downstream impacts, SRS is now developing plans for using a 1-wt% oxalic acid solution. A technology gap associated with using a 1-wt% oxalic acid solution was a dearth of suitable corrosion data. Assuming oxalic acid's passivation of carbon steel was proportional to the free oxalate concentration, the general corrosion rate (CR) from a 1-wt% solution may not be bound by those from 8-wt%. Therefore, after developing the test strategy and plan, the corrosion testing was performed. Starting with the envisioned process specific baseline solvent, a 1-wt% oxalic acid solution, with sludge (limited to Purex type sludge-simulant for this initial effort) at 75 C and agitated, the corrosion rate (CR) was determined from the measured weight loss of the exposed coupon. Environmental variations tested were: (a) Inclusion of sludge in the test vessel or assuming a pure oxalic acid solution; (b) acid solution temperature maintained at 75 or 45 C; and (c) agitation of the acid solution or stagnant. Application of select electrochemical testing (EC) explored the impact of each variation on the passivation mechanisms and confirmed the CR. The 1-wt% results were then compared to those from the 8-wt%. The immersion coupons showed that the maximum time averaged CR for a 1-wt% solution with sludge was less than 25-mils/yr for all conditions. For an agitated 8-wt% solution with sludge, the maximum time averaged CR was about 30-mils/yr at 50 C, and 86-mils/yr at 75 C. Both the 1-wt% and the 8-wt% testing demonstrated that if the sludge was removed from

  9. Corrosion behaviour of Mg-Cu and Mg-Mo composites in 3.5% NaCl

    International Nuclear Information System (INIS)

    Budruk Abhijeet, S.; Balasubramaniam, R.; Gupta, M.

    2008-01-01

    The corrosion behaviour of pure magnesium, Mg-Cu (0.3, 0.6, and 1 vol.%) and Mg-Mo (0.1, 0.3, and 0.6 vol.%) composites has been studied in 3.5% NaCl solution by weight loss and polarisation methods. Corrosion rates determined by weight loss method were considerably higher than that determined by polarisation method. The corrosion rate increased with increasing volume fraction of reinforcement in Mg-Cu and Mg-Mo composites. At the same volume fraction of reinforcement, molybdenum reinforced composite corroded faster than copper reinforced composite. The galvanic current density between Mg-Cu and Mg-Mo couples has been experimentally measured using zero resistance ammeter technique. The experimentally observed galvanic current densities were in close agreement with those obtained using mixed potential theory analysis. SEM observation of corroded samples confirmed microgalvanic activity at the matrix/reinforcement interfaces. The poor corrosion resistance of composites has been attributed to microgalvanic effects between the matrix and reinforcements and inferior quality of surface films

  10. Elasticity, electronic properties and hardness of MoC investigated by first principles calculations

    International Nuclear Information System (INIS)

    Liu, YangZhen; Jiang, YeHua; Feng, Jing; Zhou, Rong

    2013-01-01

    The crystal structure, cohesive energy, formation enthalpy, mechanical anisotropy, electronic properties and hardness of α−MoC, β−MoC and γ−MoC are investigated by the first-principles calculations. The elastic constants and the bulk moduli, shear moduli, Young's moduli are calculated. The Young's modulus values of α−MoC, β−MoC and γ−MoC are 395.6 GPa, 551.2 GPa and 399.5 GPa, respectively. The surface constructions of Young's moduli identify the mechanical anisotropy of molybdenum carbide, and the results show that anisotropy of α−MoC is stronger than others. The electronic structure indicates that the bonding behaviors of MoC are the combinations of covalent and metallic bonds. The hardness of β−MoC is obviously higher than those of α−MoC and γ−MoC

  11. Detecting the Extent of Eutectoid Transformation in U-10Mo

    Energy Technology Data Exchange (ETDEWEB)

    Devaraj, Arun [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jana, Saumyadeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McInnis, Colleen A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lombardo, Nicholas J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Joshi, Vineet V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sweet, Lucas E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Manandhar, Sandeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lavender, Curt A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-08-31

    During eutectoid transformation of U-10Mo alloy, uniform metastable γ UMo phase is expected to transform to a mixture of α-U and γ’-U2Mo phase. The presence of transformation products in final U-10Mo fuel, especially the α phase is considered detrimental for fuel irradiation performance, so it is critical to accurately evaluate the extent of transformation in the final U-10Mo alloy. This phase transformation can cause a volume change that induces a density change in final alloy. To understand this density and volume change, we developed a theoretical model to calculate the volume expansion and resultant density change of U-10Mo alloy as a function of the extent of eutectoid transformation. Based on the theoretically calculated density change for 0 to 100% transformation, we conclude that an experimental density measurement system will be challenging to employ to reliably detect and quantify the extent of transformation. Subsequently, to assess the ability of various methods to detect the transformation in U-10Mo, we annealed U-10Mo alloy samples at 500°C for various times to achieve in low, medium, and high extent of transformation. After the heat treatment at 500°C, the samples were metallographically polished and subjected to optical microscopy and x-ray diffraction (XRD) methods. Based on our assessment, optical microscopy and image processing can be used to determine the transformed area fraction, which can then be correlated with the α phase volume fraction measured by XRD analysis. XRD analysis of U-10Mo aged at 500°C detected only α phase and no γ’ was detected. To further validate the XRD results, atom probe tomography (APT) was used to understand the composition of transformed regions in U-10Mo alloys aged at 500°C for 10 hours. Based on the APT results, the lamellar transformation product was found to comprise α phase with close to 0 at% Mo and γ phase with 28–32 at% Mo, and the Mo concentration was highest at the

  12. The crisis of 99Mo. Current trends and challenges

    International Nuclear Information System (INIS)

    Leyva, René; Duatti, Adriano

    2016-01-01

    In recent years they have exacerbated the problems with the availability of 99 Mo in the international market for the production of radio isotopic generators 99 Mo / 99 mTc. The main situation is given by the shutdown, maintenance or damage to the nuclear reactors of the reductor plants. The search for solutions, analysis of alternatives and development of new methods for the 99 Mo, the well-known workhorse of nuclear medicine, are addressed in this paper. Are interesting new routes using cyclotrons. Also shown are the steps taken internationally to alleviate the growing demand against a limited supply in production. (author)

  13. Detecting the Extent of Eutectoid Transformation in U-10Mo

    International Nuclear Information System (INIS)

    Devaraj, Arun; Jana, Saumyadeep; McInnis, Colleen A.; Lombardo, Nicholas J.; Joshi, Vineet V.; Sweet, Lucas E.; Manandhar, Sandeep; Lavender, Curt A.

    2016-01-01

    During eutectoid transformation of U-10Mo alloy, uniform metastable ? UMo phase is expected to transform to a mixture of ?-U and ?'-U_2Mo phase. The presence of transformation products in final U-10Mo fuel, especially the ? phase is considered detrimental for fuel irradiation performance, so it is critical to accurately evaluate the extent of transformation in the final U-10Mo alloy. This phase transformation can cause a volume change that induces a density change in final alloy. To understand this density and volume change, we developed a theoretical model to calculate the volume expansion and resultant density change of U-10Mo alloy as a function of the extent of eutectoid transformation. Based on the theoretically calculated density change for 0 to 100% transformation, we conclude that an experimental density measurement system will be challenging to employ to reliably detect and quantify the extent of transformation. Subsequently, to assess the ability of various methods to detect the transformation in U-10Mo, we annealed U-10Mo alloy samples at 500°C for various times to achieve in low, medium, and high extent of transformation. After the heat treatment at 500°C, the samples were metallographically polished and subjected to optical microscopy and x-ray diffraction (XRD) methods. Based on our assessment, optical microscopy and image processing can be used to determine the transformed area fraction, which can then be correlated with the ? phase volume fraction measured by XRD analysis. XRD analysis of U-10Mo aged at 500°C detected only ? phase and no ?' was detected. To further validate the XRD results, atom probe tomography (APT) was used to understand the composition of transformed regions in U-10Mo alloys aged at 500°C for 10 hours. Based on the APT results, the lamellar transformation product was found to comprise ? phase with close to 0 at% Mo and ? phase with 28-32 at% Mo, and the Mo concentration was highest at the ?/? interface.

  14. Atomic layer deposition of a MoS₂ film.

    Science.gov (United States)

    Tan, Lee Kheng; Liu, Bo; Teng, Jing Hua; Guo, Shifeng; Low, Hong Yee; Tan, Hui Ru; Chong, Christy Yuen Tung; Yang, Ren Bin; Loh, Kian Ping

    2014-09-21

    A mono- to multilayer thick MoS₂ film has been grown by using the atomic layer deposition (ALD) technique at 300 °C on a sapphire wafer. ALD provides precise control of the MoS₂ film thickness due to pulsed introduction of the reactants and self-limiting reactions of MoCl₅ and H₂S. A post-deposition annealing of the ALD-deposited monolayer film improves the crystallinity of the film, which is evident from the presence of triangle-shaped crystals that exhibit strong photoluminescence in the visible range.

  15. NMR and XAS Study of Fe-Mo Double Perovskites

    International Nuclear Information System (INIS)

    Zajac, D.A.; Kapusta, C.; Borowiec, M.; Sikora, M.; Marquina, C.; Blasco, J.; Ibarra, M.R.

    2005-01-01

    The results of NMR and XAS measurements of the A 2 FeMoO 6 double perovskites (DP) (A 2 =Sr 2 , SrBa, Ba 2 , Ca 2 ) at the Fe and Mo K edges are reported and the information on the individual site electronic and magnetic properties is analysed. The compounds studied belong to the family of materials exhibiting a high field '' colossal '' magnetoresistance as well as a low field '' giant '' magnetoresistance. Magnetoresistive properties of the compounds arise from their half-metallicity, i.e. only one spin direction being populated in the conduction band, which consists of overlapping spin down 3d Fe, 2p O and 4d Mo electron bands. Within the model, a spin-down electron undergoes a fast hopping through unoccupied oxygen 2p orbitals between Fe 3+ (3d 5 - spin up) and Mo 6+ (4d 0 ) ionic cores. This mechanism implicates an anti-parallel coupling of the Fe and Mo spins and leads to non-integer magnetic moments and a metallic character below TC. The interaction, in analogy with the '' double exchange '' (DE) in manganites, is called '' double exchange-like '' interaction. The superexchange interaction (SE) is also expected to be present, resulting also in an anti-parallel coupling of 3d Fe 3+ and 4d Mo 5+ spins through occupied oxygen 2p orbitals. The insulating character of SE is connected with an increase of the tilt angle of the Fe-O-Mo bond, which is related to a change of the structural tolerance factor f and results in structural distortions. The molybdenum NMR measurements revealed the existence of a non-integer magnetic moment at Mo and Fe, which can be attributed to the DE-like interaction. However, experiments using Moessbauer spectroscopy have shown the existence of two Fe ionisation states - with integer (SE) and non integer (DE) magnetic moments. The 95 Mo and 97 Mo NMR measurements on A 2 FeMoO 6 (A 2 =Sr 2 , SrBa, Ba 2 , Ca 2 ) presented in this work show different values of the Mo hyperfine field and the corresponding magnetic moment. This is attributed

  16. A thermodynamic evaluation of the Ti-Mo-C system

    International Nuclear Information System (INIS)

    Shim, J.H.; Oh, C.S.; Lee, D.N.

    1996-01-01

    A thermodynamic assessment of the Ti-Mo-C system has been made, employing a two-sublattice regular solution model for the solid solution and carbide phases and an ordinary subregular solution model for the liquid phase. A set of thermodynamic parameters describing the Gibbs energy of each individual phase in the Ti-Mo-C as well as the Ti-Mo systems was evaluated from thermochemical and phase equilibria information available in the literature through a computer-aided optimization procedure called the CALPHAD method. The comparison between the calculated and experimental results was made and practically important phase diagrams are also presented

  17. The experience of weight management in normal weight adults.

    Science.gov (United States)

    Hernandez, Cheri Ann; Hernandez, David A; Wellington, Christine M; Kidd, Art

    2016-11-01

    No prior research has been done with normal weight persons specific to their experience of weight management. The purpose of this research was to discover the experience of weight management in normal weight individuals. Glaserian grounded theory was used. Qualitative data (focus group) and quantitative data (food diary, study questionnaire, and anthropometric measures) were collected. Weight management was an ongoing process of trying to focus on living (family, work, and social), while maintaining their normal weight targets through five consciously and unconsciously used strategies. Despite maintaining normal weights, the nutritional composition of foods eaten was grossly inadequate. These five strategies can be used to develop new weight management strategies that could be integrated into existing weight management programs, or could be developed into novel weight management interventions. Surprisingly, normal weight individuals require dietary assessment and nutrition education to prevent future negative health consequences. Copyright © 2016 Elsevier Inc. All rights reserved.

  18. The effect of holiday weight gain on body weight.

    Science.gov (United States)

    Schoeller, Dale A

    2014-07-01

    The topic of holiday weight gain has been a frequent subject of the lay media; however, scientific interest has only been recent. Multiple studies in Western societies have reported average weight gains among adults during the period between mid-November and mid-January that were about 0.5 kg. The range in individual weight changes was large, however, and the already overweight and obese gain more weight than those who are healthy weight. When the average gain across the year was also measured, the holiday weight was the major contributor to annual excess weight gain. Efforts patterned to increase awareness to energy balance and body weight have been shown to be successful at reducing such gain. An exception to holiday weight gain being a major contributor to annual excess gain has been children, in whom summer weight gains have been observed to be the major contributor to average excess weight gain. Copyright © 2014 Elsevier Inc. All rights reserved.

  19. Solid state reactions of MoO3 and Na2MoO4 with (U.85,Ce.15)O2x

    International Nuclear Information System (INIS)

    Dahale, N.D.; Keskar, Meera; Singh Mudher, K.D.; Chawla, K.L.

    1999-01-01

    (U .85 ,Ce .15 )MoO 6-x was prepared by the solid state reactions of (U .85 ,Ce .15 )O 2±x with MoO 3 in air at 600 deg C. Solid state reactions of Na 2 MoO 4 with (U .85 ,Ce .15 )MoO 6.x up to 550 deg C in air led to the formation of Na 2 (U .85 ,Ce .15 )Mo 2 O 10-x and Na 2 (U .85 , Ce .15 ) 2 Mo 3 O 16-x . These compounds were characterised by x-ray and thermal methods. The x-ray powder data of (U .85 , Ce .15 ) MoO 6-x were indexed on monoclinic system whereas, data of Na 2 (U .85 ,Ce .15 ) Mo 2 O 10-x and Na 2 (U .85 ,Ce .15 ) 2 Mo 3 O 16-x were indexed on orthorhombic and monoclinic system respectively. (author)

  20. Three-Dimensional Heterostructures of MoS 2 Nanosheets on Conducting MoO 2 as an Efficient Electrocatalyst To Enhance Hydrogen Evolution Reaction

    KAUST Repository

    Nikam, Revannath Dnyandeo

    2015-10-05

    Molybdenum disulfide (MoS) is a promising catalyst for hydrogen evolution reaction (HER) because of its unique nature to supply active sites in the reaction. However, the low density of active sites and their poor electrical conductivity have limited the performance of MoS in HER. In this work, we synthesized MoS nanosheets on three-dimensional (3D) conductive MoO via a two-step chemical vapor deposition (CVD) reaction. The 3D MoO structure can create structural disorders in MoS nanosheets (referred to as 3D MoS/MoO), which are responsible for providing the superior HER activity by exposing tremendous active sites of terminal disulfur of S2 (in MoS) as well as the backbone conductive oxide layer (of MoO) to facilitate an interfacial charge transport for the proton reduction. In addition, the MoS nanosheets could protect the inner MoO core from the acidic electrolyte in the HER. The high activity of the as-synthesized 3D MoS/MoO hybrid material in HER is attributed to the small onset overpotential of 142 mV, a largest cathodic current density of 85 mA cm, a low Tafel slope of 35.6 mV dec, and robust electrochemical durability.