Evaluation of Wax Deposition and Its Control During Production of Alaska North Slope Oils

Energy Technology Data Exchange (ETDEWEB)

Tao Zhu; Jack A. Walker; J. Liang

2008-12-31

Due to increasing oil demand, oil companies are moving into arctic environments and deep-water areas for oil production. In these regions of lower temperatures, wax deposits begin to form when the temperature in the wellbore falls below wax appearance temperature (WAT). This condition leads to reduced production rates and larger pressure drops. Wax problems in production wells are very costly due to production down time for removal of wax. Therefore, it is necessary to develop a solution to wax deposition. In order to develop a solution to wax deposition, it is essential to characterize the crude oil and study phase behavior properties. The main objective of this project was to characterize Alaskan North Slope crude oil and study the phase behavior, which was further used to develop a dynamic wax deposition model. This report summarizes the results of the various experimental studies. The subtasks completed during this study include measurement of density, molecular weight, viscosity, pour point, wax appearance temperature, wax content, rate of wax deposition using cold finger, compositional characterization of crude oil and wax obtained from wax content, gas-oil ratio, and phase behavior experiments including constant composition expansion and differential liberation. Also, included in this report is the development of a thermodynamic model to predict wax precipitation. From the experimental study of wax appearance temperature, it was found that wax can start to precipitate at temperatures as high as 40.6 C. The WAT obtained from cross-polar microscopy and viscometry was compared, and it was discovered that WAT from viscometry is overestimated. From the pour point experiment it was found that crude oil can cease to flow at a temperature of 12 C. From the experimental results of wax content, it is evident that the wax content in Alaskan North Slope crude oil can be as high as 28.57%. The highest gas-oil ratio for a live oil sample was observed to be 619.26 SCF

Oil-structuring characterization of natural waxes in canola oil oleogels: Rheological, thermal, and oxidative properties

Science.gov (United States)

Natural waxes (candelilla wax, carnauba wax, and beeswax) were utilized as canola oil structurants to produce oleogels and their physicochemical properties were evaluated from rheological, thermal, and oxidative points of view. The oleogels with candelilla wax exhibited the highest hardness, followe...

Canadian company develops better grease

International Nuclear Information System (INIS)

Anon.

1997-01-01

Development of a new type of grease for hydroelectric applications that offers improved performance characteristics and reduced environmental side-effects was discussed. The new product developed by Utility Services Associates of Toronto and known as Cor-Tek VSG, performs better than most mineral oil-based greases. It is readily bio-degradable and contains none of the environmentally questionable additives used in greases. It is made primarily of canola oil, a renewable resource. It has excellent resistance to water washout, retards rust formation, has an extreme pressure rating, is compatible with most of the current greases, works well in both manual and automatic greasing systems, and is said to be excellent for lignum vitae main bearings on a Kaplan turbine

Prediction of wax buildup in 24 inch cold, deep sea oil loading line

Energy Technology Data Exchange (ETDEWEB)

Asperger, R.G.; Sattler, R.E.; Tolonen, W.J.; Pitchford, A.C.

1981-10-01

When designing pipelines for cold environments, it is important to know how to predict potential problems due to wax deposition on the pipeline's inner surface. The goal of this work was to determine the rate of wax buildup and the maximum, equlibrium wax thickness for a North Sea field loading line. The experimental techniques and results used to evaluate the waxing potential of the crude oil (B) are described. Also, the theoretic model which was used for predicting the maximum wax deposit thickness in the crude oil (B) loading pipeline at controlled temperatures of 40 F (4.4 C) and 100 F (38 C), is illustrated. Included is a recommendation of a procedure for using hot oil at the end of a tanker loading period in order to dewax the crude oil (B) line. This technique would give maximum heating of the pipeline and should be followed by shutting the hot oil into the pipeline at the end of the loading cycle which will provide a hot oil soaking to help soften existing wax. 14 references.

Effect of asphaltenes on crude oil wax crystallization

DEFF Research Database (Denmark)

Kriz, Pavel; Andersen, Simon Ivar

2005-01-01

The paper summarizes the experimental work done on asphaltene influenced wax crystallization. Three different asphaltenes (from stable oil, instable oil, and deposit) were mixed at several concentrations or dispersions into the waxy crude oil. These blends were evaluated by viscometry and yield s...

Fat, oil and grease reduction in commercial kitchen ductwork: a novel biological approach

OpenAIRE

Mudie, S.; Vahdati, Maria

2017-01-01

Recent research has characterised emissions upon cooking a variety of foods in a commercial catering environment in terms of volume, particle size and composition. However, there has been limited focus on the deposition of solid grease in commercial kitchen ductwork, the sustainability of these systems and their implications on the heat recovery potential of kitchen ventilation extract air.\\ud \\ud This paper reviews the literature concerning grease, commonly referred to as Fat, Oils and Greas...

Synthesis of oleyl oleate wax esters in Arabidopsis thaliana and Camelina sativa seed oil.

Science.gov (United States)

Iven, Tim; Hornung, Ellen; Heilmann, Mareike; Feussner, Ivo

2016-01-01

Seed oil composed of wax esters with long-chain monoenoic acyl moieties represents a high-value commodity for industry. Such plant-derived sperm oil-like liquid wax esters are biodegradable and can have excellent properties for lubrication. In addition, wax ester oil may represent a superior substrate for biodiesel production. In this study, we demonstrate that the low-input oil seed crop Camelina sativa can serve as a biotechnological platform for environmentally benign wax ester production. Two biosynthetic steps catalysed by a fatty alcohol-forming acyl-CoA reductase (FAR) and a wax ester synthase (WS) are sufficient to achieve wax ester accumulation from acyl-CoA substrates. To produce plant-derived sperm oil-like liquid wax esters, the WS from Mus musculus (MmWS) or Simmondsia chinensis (ScWS) were expressed in combination with the FAR from Mus musculus (MmFAR1) or Marinobacter aquaeolei (MaFAR) in seeds of Arabidopsis thaliana and Camelina sativa. The three analysed enzyme combinations Oleo3:mCherry:MmFAR1∆c/Oleo3:EYFP:MmWS, Oleo3:mCherry:MmFAR1∆c/ScWS and MaFAR/ScWS showed differences in the wax ester molecular species profiles and overall biosynthetic performance. By expressing MaFAR/ScWS in Arabidopsis or Camelina up to 59% or 21% of the seed oil TAGs were replaced by wax esters, respectively. This combination also yielded wax ester molecular species with highest content of monounsaturated acyl moieties. Expression of the enzyme combinations in the Arabidopsis fae1 fad2 mutant background high in oleic acid resulted in wax ester accumulation enriched in oleyl oleate (18:1/18:1 > 60%), suggesting that similar values may be obtained with a Camelina high oleic acid line. © 2015 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

Use of Bio-Amp, a commercial bio-additive for the treatment of grease trap wastewater containing fat, oil, and grease.

Science.gov (United States)

Tang, Hao L; Xie, Yuefeng F; Chen, Yen-Chih

2012-11-01

This research investigated the application of Bio-Amp, a commercial bio-additive for the treatment of fat, oil, and grease (FOG) in a grease trap, and evaluated potential impacts of treated effluent on downstream collection system and treatment processes. Results show that after Bio-Amp treatment, FOG deposit formation was reduced by 40%, implicating a potential reduction of sewer line blockages. Chemical oxygen demand (COD), total nitrogen (TN), total phosphorus (TP) and total fatty acids were reduced by 39%, 33%, 56%, and 59%, respectively, which represents an overall loading reduction of 9% COD, 5% TN and 40% TP received by the treatment plant from all the dining halls. On the other hand, readily biodegradable COD fractions significantly increased, which implies a potential improvement on Bio-P removal. Overall, the results showed that application of Bio-Amp in grease trap provides potential reduction of sewer line blockages, and can also alleviate downstream treatment burden. Copyright © 2012 Elsevier Ltd. All rights reserved.

Simultaneous removal of oil and grease, and heavy metals from artificial bilge water using electro-coagulation/flotation.

Science.gov (United States)

Rincón, Guillermo J; La Motta, Enrique J

2014-11-01

US and international regulations pertaining to the control of bilge water discharges from ships have concentrated their attention to the levels of oil and grease rather than to the heavy metal concentrations. The consensus is that any discharge of bilge water (and oily water emulsion within 12 nautical miles from the nearest land cannot exceed 15 parts per million (ppm). Since there is no specific regulation for metal pollutants under the bilge water section, reference standards regulating heavy metal concentrations are taken from the ambient water quality criteria to protect aquatic life. The research herein presented discusses electro-coagulation (EC) as a method to treat bilge water, with a focus on oily emulsions and heavy metals (copper, nickel and zinc) removal efficiency. Experiments were run using a continuous flow reactor, manufactured by Ecolotron, Inc., and a synthetic emulsion as artificial bilge water. The synthetic emulsion contained 5000 mg/L of oil and grease, 5 mg/L of copper, 1.5 mg/L of nickel, and 2.5 mg/l of zinc. The experimental results demonstrate that EC is very efficient in removing oil and grease. For oil and grease removal, the best treatment and cost efficiency was obtained when using a combination of carbon steel and aluminum electrodes, at a detention time less than one minute, a flow rate of 1 L/min and 0.6 A/cm(2) of current density. The final effluent oil and grease concentration, before filtration, was always less than 10 mg/L. For heavy metal removal, the combination of aluminum and carbon steel electrodes, flow rate of 1 L/min, effluent recycling, and 7.5 amps produced 99% zinc removal efficiency. Copper and nickel are harder to remove, and a removal efficiency of 70% was achieved. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fats, oils, and grease : options for plant-level treatment of a national problem

Energy Technology Data Exchange (ETDEWEB)

Miles, E.; Scherffius, B. [EcoPlus Inc. Charlotte, NC (United States)

2007-09-15

Fats, oils, and grease from restaurants and homes can congeal in sewers and result in damaging runoff into rivers and streams. A growing number of food service establishments are now producing increasing amounts of a specific grease product called brown grease, which is sticky and difficult to remove. Regulations now require haulers to remove the waste and dispose of it. However, many local treatment plants cannot accept or dispose of the amounts of grease currently being produced. A total of volume of 3 to 10 billion gallons per year of contaminated water have been accidentally discharged from sanitary sewers as a result of brown grease accumulations. This paper provided details of the EcoPlus Final Treatment Facility, which can be set up at waste water treatment plants and is able to process brown grease and discharge supernatant water from its process back into city sewers. The EcoPlus process produces 2 waste streams: (1) a low strength aqueous solution that can be disposed of in a sanitary sewer tap; and (2) a granular material that can be disposed of in a landfill for use as a soil conditioner. It was concluded that the granular material can also be used facilitate the incineration of sewage sludge, or burned as an alternative green fuel for power generation. 4 figs.

Production of wax esters via microbial oil synthesis from food industry waste and by-product streams.

Science.gov (United States)

Papadaki, Aikaterini; Mallouchos, Athanasios; Efthymiou, Maria-Nefeli; Gardeli, Chryssavgi; Kopsahelis, Nikolaos; Aguieiras, Erika C G; Freire, Denise M G; Papanikolaou, Seraphim; Koutinas, Apostolis A

2017-12-01

The production of wax esters using microbial oils was demonstrated in this study. Microbial oils produced from food waste and by-product streams by three oleaginous yeasts were converted into wax esters via enzymatic catalysis. Palm oil was initially used to evaluate the influence of temperature and enzyme activity on wax ester synthesis catalysed by Novozyme 435 and Lipozyme lipases using cetyl, oleyl and behenyl alcohols. The highest conversion yields (up to 79.6%) were achieved using 4U/g of Novozyme 435 at 70°C. Transesterification of microbial oils to behenyl and cetyl esters was achieved at conversion yields up to 87.3% and 69.1%, respectively. Novozyme 435 was efficiently reused for six and three cycles during palm esters and microbial esters synthesis, respectively. The physicochemical properties of microbial oil derived behenyl esters were comparable to natural waxes. Wax esters from microbial oils have potential applications in cosmetics, chemical and food industries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Investigation of wax precipitation in crude oil: Experimental and modeling

Directory of Open Access Journals (Sweden)

Taraneh Jafari Behbahani

2015-09-01

Full Text Available In this work, a series of experiments were carried to investigation of rheological behavior of crude oil using waxy crude oil sample in the absence/presence of flow improver such as ethylene-vinyl acetate copolymer. The rheological data covered the temperature range of 5–30 °C. The results indicated that the performance of flow improver was dependent on its molecular weight. Addition of small quantities of flow improver, can improve viscosity and pour point of crude oil. Also, an Artificial Neural Network (ANN model using Multi-Layer Perceptron (MLP topology has been developed to account wax appearance temperature and the amount of precipitated wax and the model was verified using experimental data given in this work and reported in the literature. In order to compare the performance of the proposed model based on Artificial Neural Network, the wax precipitation experimental data at different temperatures were predicted using solid solution model and multi-solid phase model. The results showed that the developed model based on Artificial Neural Network can predict more accurately the wax precipitation experimental data in comparison to the previous models such as solid solution and multi-solid phase model with AADs less than 0.5%. Furthermore, the number of parameters required for the Artificial Neural Network (ANN model is less than the studied thermodynamic models.

Physical properties of beeswax, sunflower wax, and candelilla wax mixtures and organogels

Science.gov (United States)

There is increased interest in natural waxes as alternatives to partially hydrogenated oils and saturated fats as oil structuring agents. Using relatively low concentrations (0.5-5%), natural waxes are able to form crystalline networks, or organogels, which bind liquid oil. Each natural wax is uniqu...

Evaluation of methods for wax determination in crude oil; Avaliacao de metodos de determinacao de parafinas em petroleo

Energy Technology Data Exchange (ETDEWEB)

Dias, Julio Cesar M.; Silva, Maria do Socorro A.J. da; Vasconcellos, Rosa C.U. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Tamanqueira, Juliana B. [Fundacao Gorceix, Ouro Preto, MG (Brazil)

2008-07-01

Determining the wax content of crude oil is of great importance for petroleum industry, especially for production, storage and transportation of crude oils. Many different methodologies of wax determining are available in the technical literature. However, the selection of the most suitable method must be in accordance with the aim of the analysis and observing the specificities of each technique. The purpose of this work was to determine the performance of different techniques of wax determining applied to characterization of precipitation properties of waxy compounds in crude oils. Twelve samples of crude oils proceeding from the main Brazilian oil producing sedimentary basins were selected for this study. These samples were analyzed by three important analytical techniques of wax determining: precipitation by cooled solvent; liquid chromatography with precipitation by cooled solvent; and liquid chromatography followed by gas chromatography. Differential scanning calorimetry data related to the wax crystallization in these oils were used as parameters of validation. The results obtained in this study indicate that the liquid chromatography followed by gas chromatography method has the best performance for wax determining in crude oils. (author)

Wax ester profiling of seed oil by nano-electrospray ionization tandem mass spectrometry

Science.gov (United States)

2013-01-01

Background Wax esters are highly hydrophobic neutral lipids that are major constituents of the cutin and suberin layer. Moreover they have favorable properties as a commodity for industrial applications. Through transgenic expression of wax ester biosynthetic genes in oilseed crops, it is possible to achieve high level accumulation of defined wax ester compositions within the seed oil to provide a sustainable source for such high value lipids. The fatty alcohol moiety of the wax esters is formed from plant-endogenous acyl-CoAs by the action of fatty acyl reductases (FAR). In a second step the fatty alcohol is condensed with acyl-CoA by a wax synthase (WS) to form a wax ester. In order to evaluate the specificity of wax ester biosynthesis, analytical methods are needed that provide detailed wax ester profiles from complex lipid extracts. Results We present a direct infusion ESI-tandem MS method that allows the semi-quantitative determination of wax ester compositions from complex lipid mixtures covering 784 even chain molecular species. The definition of calibration prototype groups that combine wax esters according to their fragmentation behavior enables fast quantitative analysis by applying multiple reaction monitoring. This provides a tool to analyze wax layer composition or determine whether seeds accumulate a desired wax ester profile. Besides the profiling method, we provide general information on wax ester analysis by the systematic definition of wax ester prototypes according to their collision-induced dissociation spectra. We applied the developed method for wax ester profiling of the well characterized jojoba seed oil and compared the profile with wax ester-accumulating Arabidopsis thaliana expressing the wax ester biosynthetic genes MaFAR and ScWS. Conclusions We developed a fast profiling method for wax ester analysis on the molecular species level. This method is suitable to screen large numbers of transgenic plants as well as other wax ester samples

Treatability and kinetics studies of mesophilic aerobic biodegradation of high oil and grease pet food wastewater

International Nuclear Information System (INIS)

Liu, Victor Lei; Nakhla, G.; Bassi, A.

2004-01-01

In this work, batch activated sludge studies were investigated for the treatment of raw pet food wastewater characterized by oil and grease concentrations of 50,000-66,000 mg/L, COD and BOD concentrations of 100,000 and 80,000 mg/L, respectively, as well as effluent from an existing anaerobic digester treating the aforementioned wastewater. A pre-treatment process, dissolved air flotation (DAF) achieved 97-99% reduction in O and G to about 400-800 mg/L, which is still atypically high for AS. The batch studies were conducted using a 4-L bioreactor at room temperature (21 deg. C) under different conditions. The experimental results showed for the DAF pretreated effluent, 92% COD removal efficiency can be achieved by using conventional activated sludge system at a 5 days contact time and applied initial soluble COD to biomass ratio of 1.17 mg COD/mg VSS. Similarly for the digester effluent at average oil and grease concentrations of 13,500 mg/L, activated sludge affected 63.7-76.2% soluble COD removal at 5 days. The results also showed that all kinetic data best conformed to the zero order biodegradation model with a low biomass specific maximum substrate utilization rate of 0.168 mg COD/mg VSS day reflecting the slow biodegradability of the wastewater even after 99% removal of oil and grease

Review of data on the dermal penetration of mineral oils and waxes used in cosmetic applications.

Science.gov (United States)

Petry, T; Bury, D; Fautz, R; Hauser, M; Huber, B; Markowetz, A; Mishra, S; Rettinger, K; Schuh, W; Teichert, T

2017-10-05

Mineral oils and waxes used in cosmetic products, also referred to as "personal care products" outside the European Union, are mixtures of predominantly saturated hydrocarbons consisting of straight-chain, branched and ring structures with carbon chain lengths greater than C16. They are used in skin and lip care cosmetic products due to their excellent skin tolerance as well as their high protecting and cleansing performance and broad viscosity options. Recently, concerns have been raised regarding potential adverse health effects of mineral oils and waxes from dermal application of cosmetics. In order to be able to assess the risk for the consumer the dermal penetration potential of these ingredients has to be evaluated. The scope and objective of this review are to identify and summarize publicly available literature on the dermal penetration of mineral oils and waxes as used in cosmetic products. For this purpose, a comprehensive literature search was conducted. A total of 13 in vivo (human, animal) and in vitro studies investigating the dermal penetration of mineral oils and waxes has been identified and analysed. The majority of the substances were dermally adsorbed to the stratum corneum and only a minor fraction reached deeper skin layers. Overall, there is no evidence from the various studies that mineral oils and waxes are percutaneously absorbed and become systemically available. Thus, given the absence of dermal uptake, mineral oils and waxes as used in cosmetic products do not present a risk to the health of the consumer. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

The processing of used cooking oil (yellow grease) using combination of adsorption and ultrafiltration membrane processes

Science.gov (United States)

Rosnelly, C. M.; Sofyana; Amalia, D.; Sarah, S.

2018-03-01

Yellow grease is used cooking oil whose quality has degraded due to the oxidation, polymerization, or hydrolysis process. In previous studies, yellow grease refining had been conducted either by adsorption or by using membrane. In this study, adsorption process using adsorbent from bagasse activated with H3PO4 12.5%, and ultrafiltration using Polyethersulfone (PES) membrane were combined. In adsorption stage, several variation of bagasse mass was fed into 200 ml of yellow grease and stirred for 60 minutes at 60 rpm. Yellow grease produced from adsorption with best condition was then processed using ultrafiltration membran that is PES membran with concentration by 15 wt % with transmembrane pressure variation by 0.5; 1; 1.5; 2; and 2.5 Bar. Analysis of yellow grease characteristics before refined showed its acid number, peroxide number, iodine number, and water content respectively by 2.68 mgKOH/Kg; 5.97 Meq/Kg; 51,48; and 1.29%. Characteristics of yellow grease after adsorption at its best condition on the parameters of acid number, peroxide number, iodine number, and water content are respectively by 2.55 mgKOH/Kg; 4.19 Meq/Kg; 40,02; and 0.27%. Characteristics of yellow grease after ultrafiltration at its best condition on the parameters of acid number, peroxide number, iodine number, and water content are respectively by 1.12 mgKOH/Kg; 1.8 Meq/Kg; 41,36; and 0.02%. Combination of adsorption and ultrafiltration processes for yellow grease processing showed decreasing value on the parameters of acid number, peroxide number, and water content that conforms to the SNI quality standard, but has not been able to increase the iodine number.

Thermodynamics Prediction of Wax Precipitation in Black Oil Using Regular Solution Model and Plus Fraction Characterization

Directory of Open Access Journals (Sweden)

Wei Wang

2013-01-01

Full Text Available The precipitation of wax/solid paraffin during production, transportation, and processing of crude oil is a serious problem. It is essential to have a reliable model to predict the wax appearance temperature and the amount of solid precipitated at different conditions. This paper presents a work to predict the solid precipitation based on solid-liquid equilibrium with regular solution-molecular thermodynamic theory and characterization of the crude oil plus fraction. Due to the differences of solubility characteristics between solid and liquid phase, the solubility parameters of liquid and solid phase are calculated by a modified model. The heat capacity change between solid and liquid phase is considered and estimated in the thermodynamic model. An activity coefficient based thermodynamic method combined with two characteristic methods to calculate wax precipitation in crude oil, especially heavy oil, has been tested with experimental data. The results show that the wax appearance temperature and the amount of weight precipitated can be predicted well with the experimental data.

Simple Synthesis Hydrogenated Castor Oil Fatty Amide Wax and Its Coating Characterization.

Science.gov (United States)

Yu, Xiuzhu; Wang, Ning; Zhang, Rui; Zhao, Zhong

2017-07-01

A simple method for incorporating amine groups in hydrogenated castor oil (HCO) to produce wax for beeswax or carnauba wax substitution in packaging and coating was developed. From the conversion rate of the products, HCO was reacted with ethanolamine at 150°C for 5 h, and the molar ratio of HCO and ethanolamine was 1:4. The hardness of the final product was seven times higher than that of beeswax, the cohesiveness of the final product was 1.3 times higher than that of beeswax and approximately one half of that of carnauba wax, and the melting point of the final product is 98°C. The Fourier transform Infrared spectroscopy showed that the amide groups were incorporated to form the amide products. In coating application, the results showed that the force of the final product coating cardboard was higher than that of beeswax and paraffin wax and less than that of carnauba wax. After 24 h soaking, the compression forces were decreased. HCO fatty acid wax can be an alternative wax for carnauba wax and beeswax in coating applications.

International evolution of fat, oil and grease (FOG) waste management - A review

OpenAIRE

Wallace, Thomas; Gibbons, David; O'Dwyer, Michael; Curran, Thomas P.

2017-01-01

In recent years, issues relating to fat, oil and grease (FOG) in sewer systems have intensified. In the media, sewer blockages caused by FOG waste deposits, commonly referred to as 'fatbergs', are becoming a reminder of the problems that FOG waste can cause when left untreated. These FOG blockages lead to sanitary sewer overflows, property flooding and contamination of water bodies with sewage. Despite these financial and environmentally detrimental effects, a homogenous FOG waste management ...

Film Thickness and Friction Relationship in Grease Lubricated Rough Contacts

Directory of Open Access Journals (Sweden)

David Gonçalves

2017-08-01

Full Text Available The relationship between the film generation and the coefficient of friction in grease lubricated contacts was investigated. Ball-on-disc tests were performed under different operating conditions: entrainment speed, lubricant temperature and surface roughness. The tests were performed with fully formulated greases and their base oils. The greases were formulated with different thickener types and also different base oils natures and viscosities. Film thickness measurements were performed in ball-on-glass disc tests, and Stribeck curves were measured in ball-on-steel disc tests with discs of different roughness. The role of the thickener and the base oil nature/viscosity on the film thickness and coefficient of friction was addressed and the greases’ performance was compared based on their formulation.

Biodiesel from Jojoba oil-wax: Transesterification with methanol and properties as a fuel

Energy Technology Data Exchange (ETDEWEB)

Canoira, Laureano; Alcantara, Ramon; Garcia-Martinez, Jesus; Carrasco, Jesus [Department of Chemical Engineering and Fuels, School of Mines, Polytechnic University of Madrid, Rios Rosas 21, 28003-Madrid (Spain)

2006-01-15

The Jojoba oil-wax is extracted from the seeds of the Jojoba (Simmondsia chinensis Link Schneider), a perennial shrub that grows in semi desert areas in some parts of the world. The main uses of Jojoba oil-wax are in the cosmetics and pharmaceutical industry, but new uses could arise related to the search of new energetic crops. This paper summarizes a process to convert the Jojoba oil-wax to biodiesel by transesterification with methanol, catalysed with sodium methoxide (1wt% of the oil). The transesterification reaction has been carried out in an autoclave at 60 deg C, with a molar ratio methanol/oil 7.5:1, and vigorous stirring (600rpm), reaching a quantitative conversion of the oil after 4h. The separation of the fatty acid methyl esters (the fraction rich in FAME, 79% FAME mixture; 21% fatty alcohols; 51% of methyl cis-11-eicosenoate) from the fatty alcohols rich fraction (72% fatty alcohols; 28% FAME mixture; 26% of cis-11-eicosen-1-ol, 36% of cis-13-docosen-1-ol) has been accomplished in a single crystallization step at low temperature (-18 deg C) from low boiling point petroleum ether. The fraction rich in FAME has a density (at 15 deg C), a kinematic viscosity (at 40 deg C), a cold filter plugging point and a high calorific value in the range of the European standard for biodiesel (EN 14214)

Experimental Comparison of the Behavior between Base Oil and Grease Starvation Based on Inlet Film Thickness

Directory of Open Access Journals (Sweden)

D. Kostal

2017-03-01

Full Text Available This paper deals with the experimental study of an elastohydrodynamic contact under conditions of insufficient lubricant supply. Starvation level of this type of the contact may be experimentally determined based on the position of the meniscus, but this way can't determine all levels of starvation. Consequent development in the field of tribology achieved theoretical model that can determine all levels of starvation by dependency on the thickness of the lubricant film entering the contact, but it is difficult for experimental verification. The main goal of this work is an experimental study and description of the behavior of the elastohydrodynamic contact with controlled thickness of the lubricant film at the contact input. Contact was lubricated by the base oil and the grease and compared. Results were surprising because the only differences between oil and grease were observed for more viscous lubricants at thicker film layer entering to the contact.

Neutral Lipid Biosynthesis in Engineered Escherichia coli: Jojoba Oil-Like Wax Esters and Fatty Acid Butyl Esters

OpenAIRE

Kalscheuer, Rainer; Stöveken, Tim; Luftmann, Heinrich; Malkus, Ursula; Reichelt, Rudolf; Steinbüchel, Alexander

2006-01-01

Wax esters are esters of long-chain fatty acids and long-chain fatty alcohols which are of considerable commercial importance and are produced on a scale of 3 million tons per year. The oil from the jojoba plant (Simmondsia chinensis) is the main biological source of wax esters. Although it has a multitude of potential applications, the use of jojoba oil is restricted, due to its high price. In this study, we describe the establishment of heterologous wax ester biosynthesis in a recombinant E...

Microbial community adaptation influences long-chain fatty acid conversion during anaerobic codigestion of fats, oils, and grease with municipal sludge.

Science.gov (United States)

Ziels, Ryan M; Karlsson, Anna; Beck, David A C; Ejlertsson, Jörgen; Yekta, Sepehr Shakeri; Bjorn, Annika; Stensel, H David; Svensson, Bo H

2016-10-15

Codigesting fats, oils, and greases with municipal wastewater sludge can greatly improve biomethane recovery at wastewater treatment facilities. Process loading rates of fats, oils, and greases have been previously tested with little knowledge of the digester microbial community structure, and high transient fat loadings have led to long chain fatty acid (LCFA) accumulation and digester upsets. This study utilized recently-developed quantitative PCR assays for syntrophic LCFA-degrading bacteria along with 16S amplicon sequencing to relate changes in microbial community structure to LCFA accumulation during transient loading increases to an anaerobic codigester receiving waste restaurant oil and municipal wastewater sludge. The 16S rRNA gene concentration of the syntrophic β-oxidizing genus Syntrophomonas increased to ∼15% of the Bacteria community in the codigester, but stayed below 3% in the control digester that was fed only wastewater sludge. Methanosaeta and Methanospirillum were the dominant methanogenic genera enriched in the codigester, and together comprised over 80% of the Archaea community by the end of the experimental period. Constrained ordination showed that changes in the codigester Bacteria and Archaea community structures were related to measures of digester performance. Notably, the effluent LCFA concentration in the codigester was positively correlated to the specific loading rate of waste oil normalized to the Syntrophomonas 16S rRNA concentration. Specific loading rates of 0-1.5 × 10(-12) g VS oil/16S gene copies-day resulted in LCFA concentrations below 30 mg/g TS, whereas LCFA accumulated up to 104 mg/g TS at higher transient loading rates. Based on the community-dependent loading limitations found, enhanced biomethane production from high loadings of fats, oils and greases can be achieved by promoting a higher biomass of slow-growing syntrophic consortia, such as with longer digester solids retention times. This work also

Purifying oils and waxes. [British patent

Energy Technology Data Exchange (ETDEWEB)

1926-01-27

Fractions of petroleum, shale oil, coal oil, and paraffin wax are refined by passing the vapour under reduced pressure through fuller's earth, bauxite, silica gel, or other adsorbent at a temperature not substantially more than sufficient to maintain the vapour phase. The vapour may be passed in succession through adsorbent of increasing strength. Treatment with sulphuric acid, or with alkali, or with both may precede treatment with absorbent, and this successive treatment may be repeated any number of times. The action is accelerated by passing a current of inert gas insufficient to affect the vacuum materially along with the vapours. In an example a 160 to 225/sup 0/C kerosene fraction is treated with sulphuric acid of 10 percent strength, and passed into a fuller's earth chamber under a vacuum of 27 in. of mercury and heated by steam to about 140/sup 0/C. The apparatus is described.

Neutral lipid biosynthesis in engineered Escherichia coli: jojoba oil-like wax esters and fatty acid butyl esters.

Science.gov (United States)

Kalscheuer, Rainer; Stöveken, Tim; Luftmann, Heinrich; Malkus, Ursula; Reichelt, Rudolf; Steinbüchel, Alexander

2006-02-01

Wax esters are esters of long-chain fatty acids and long-chain fatty alcohols which are of considerable commercial importance and are produced on a scale of 3 million tons per year. The oil from the jojoba plant (Simmondsia chinensis) is the main biological source of wax esters. Although it has a multitude of potential applications, the use of jojoba oil is restricted, due to its high price. In this study, we describe the establishment of heterologous wax ester biosynthesis in a recombinant Escherichia coli strain by coexpression of a fatty alcohol-producing bifunctional acyl-coenzyme A reductase from the jojoba plant and a bacterial wax ester synthase from Acinetobacter baylyi strain ADP1, catalyzing the esterification of fatty alcohols and coenzyme A thioesters of fatty acids. In the presence of oleate, jojoba oil-like wax esters such as palmityl oleate, palmityl palmitoleate, and oleyl oleate were produced, amounting to up to ca. 1% of the cellular dry weight. In addition to wax esters, fatty acid butyl esters were unexpectedly observed in the presence of oleate. The latter could be attributed to solvent residues of 1-butanol present in the medium component, Bacto tryptone. Neutral lipids produced in recombinant E. coli were accumulated as intracytoplasmic inclusions, demonstrating that the formation and structural integrity of bacterial lipid bodies do not require specific structural proteins. This is the first report on substantial biosynthesis and accumulation of neutral lipids in E. coli, which might open new perspectives for the biotechnological production of cheap jojoba oil equivalents from inexpensive resources employing recombinant microorganisms.

Semi-continuous anaerobic co-digestion of thickened waste activated sludge and fat, oil and grease

International Nuclear Information System (INIS)

Wan Caixia; Zhou Quancheng; Fu Guiming; Li Yebo

2011-01-01

Highlights: → Co-digestion of thickened waste activated sludge (TWAS) with fat, oil and grease (FOG). → Co-digestion of TWAS and FOG at 64% VS increased biogas production by 137%. → FOG addition ratio at 74% of total VS caused inhibition of the anaerobic digestion process. → Micronutrients addition did not significantly improve the biogas production and digestion stabilization. - Abstract: Co-digestion of thickened waste activated sludge (TWAS) and fat, oil and grease (FOG) was conducted semi-continuously under mesophilic conditions. The results showed that daily methane yield at the steady state was 598 L/kg VS added when TWAS and FOG (64% of total VS) were co-digested, which was 137% higher than that obtained from digestion of TWAS alone. The biogas composition was stabilized at a CH 4 and CO 2 content of 66.8% and 29.5%, respectively. Micronutrients added to co-digestion did not improve the biogas production and digestion stabilization. With a higher addition of FOG (74% of total VS), the digester initially failed but was slowly self-recovered; however, the methane yield was only about 50% of a healthy reactor with the same organic loading rate.

Fat, oil and grease reduction in commercial kitchen ductwork: A novel biological approach.

Science.gov (United States)

Mudie, S; Vahdati, M

2017-03-01

Recent research has characterised emissions upon cooking a variety of foods in a commercial catering environment in terms of volume, particle size and composition. However, there has been limited focus on the deposition of solid grease in commercial kitchen ductwork, the sustainability of these systems and their implications on the heat recovery potential of kitchen ventilation extract air. This paper reviews the literature concerning grease, commonly referred to as Fat, Oils and Grease (FOG) abatement strategies and finds that many of these systems fall short of claimed performances. Furthermore these technologies often add to the energy cost of the operation and reduce the potential application of heat recovery in the ventilation ductwork. The aim of this study was to develop and evaluate a novel FOG removal system, with a focus on low environmental impact. The novel FOG removal system, utilises the biological activity of Bacillus subtilis and associated enzymes. The biological reagent is delivered via a misting system. The temperature, relative humidity and FOG deposit thickness were measured in the ductwork throughout a 3month trial period. FOG deposit thickness was reduced by 47% within 7weeks. The system was found to be effective at reducing the FOG deposit thickness with minimal energy cost and impact upon the kitchen and external environment. Internal ductwork operating temperature was measured with respect to future heat recovery potential and a reduction of 7°C was observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Field Demonstration for Biodegradable Military Multipurpose Grease

National Research Council Canada - National Science Library

Rhee, In-Sik

2001-01-01

Soils and ground water at many military facilities throughout the United States have been contaminated with petroleum based products, such as engine oils, greases, hydraulic fluids, and fuels, often...

Accelerated Testing of UH-60 Viscous Bearings for Degraded Grease Fault

Science.gov (United States)

Dykas, Brian; Hood, Adrian; Krantz, Timothy; Klemmer, Marko

2015-01-01

An accelerated aging investigation of critical aviation bearings lubricated with MIL-PRF- 81322 grease was conducted to derive an understanding of the mechanisms of grease degradation and loss of lubrication over time. The current study focuses on UH-60 Black Hawk viscous damper bearings supporting the tail rotor driveshaft, which were subjected to more than 5800 hours of testing in a heated environment to accelerate the deterioration of the grease. The mechanism of grease degradation is a reduction in the oil/thickener ratio rather than the expected chemical degradation of grease constituents. Over the course of testing, vibration and temperature monitoring of bearings was conducted and trends for failing bearings are presented.

Effects of irradiation in combination with waxing on the essential oils in orange peel

International Nuclear Information System (INIS)

Moussaid, M.; Lacroix, M.; Nketsia-Tabiri, J.; Boubekri, C.

2000-01-01

The study evaluated the effects of waxing and irradiation dose on the essential oils in orange peel. Mature oranges (Maroc late) waxed or unwaxed were treated with 0-2 kGy radiation. Volatiles in the peel were extracted and analyzed by G.C. D-limonene was significantly lower (P≤0.05) in waxed oranges; levels in samples treated with 2 kGy were higher than those treated with 0 or 1 kGy. Linalool, methyl anthranilate and 3.7-dimethyl-2.6-octadienal decreased as the dose increased. The analysis of variance indicates that only linalool was influenced by post-irradiation storage time. The level of this compound increased with storage time. (author)

Tribological Performance of Some Pennzane(Registered Trademark) Based Greases for Vacuum Applications

Science.gov (United States)

Marchetti, Mario; Jones, William R., Jr.; Street, Kenneth W.; Wheeler, Donald; Dixon, Duane; Jansen, Mark J.; Kimura, Hiroshi

2002-01-01

Commercial greases for space applications usually fulfill the requirements imposed by the severe conditions of use. The main requirement is their ability to create an EHL film, boundary film, or both under speed, load and temperature conditions that the mechanisms will operate. Three greases, all based on a multiply alkylated cyclopentane (Pennzan(R)) base oil, were studied. The thickeners were an n-octadecylterephthalamate soap, a lithium soap, and a urea derivative. A Four-Ball Tribometer and a Spiral Orbit Tribometer were employed to evaluate the greases under ultrahigh vacuum. Results indicated that all three greases yielded very low wear rates and extended lifetimes. In addition, routine physical property data is reported for each grease.

Case study of the effectiveness of passive grease trap for management on domestic kitchen waste water

Science.gov (United States)

Nidzamuddin, M. Y.; Juffrizal, K.; Mustapha, F.; Zulfattah, Z. M.; Tan, C. F.; Taha, M. M.; Hidayah, I.; Hilwa, M. Z.

2015-05-01

Household waste, generally known as trash or garbage is mostly includes food wastes, product packaging, and other miscellaneous inorganic wastes that are coming from domestic household. Grease waste such as oil and fats can contaminate water and also clot on pipes provoking blockages. Thus, waste water from kitchen sink need a proper way of filtration. Grease trap developed in this paper is viable in trapping the grease residue. The experiments have been conducted in controlled environment and the objectives are to investigate the effectiveness of grease trap by proving the existence of retention time and the expected ratio of collected water and oil during experiment process using a prototype model.

Food Grade Grease Berbahan Baku Minyak Sawit Crude Palm Oil (Cpo Off Grade Dengan Variasi Konsentrasi Thickening

Directory of Open Access Journals (Sweden)

Martanto Totok

2017-03-01

Full Text Available Food grade grease (FGG is a kind of lubricant made from vegetable oil. Food Grease isconsidered safe for healthy and it does not pollute the environment so that it can be veryimportant for particular industries such as pharmaceutical, animal feeding, cosmetic, andespecially food industry. This study is aiming at obtaining optimum basic formulation ofthickening agent (LiOH that can produce qualified food grade grease. It is a kind of factorialexperimental study by using complete random sampling. Based on Fisher test, the treatmentshows a different result significantly. Then, it is continued by conducting Duncan’s MultipleRange Test (DMRT. 2% of activated charcoal is the best treatment because it results FFAscore, lower water content, and the bright yellow color that is shown by the score of 5.48%,0.0498 %, and 3 % that successively obtained. The treatment on thickening agent (LiOH(P1 and the revious one (L1 are the best treatment which produce qualified food gradegrease, corrosion resistance value 12.0, dropping point 130C, lubricating texture value 1,pH value 9.45, water content 0.19%, and ash content value 0.76%.

Content of Wax during Dewaxing Process: Adopting a DOE Method

Directory of Open Access Journals (Sweden)

Mohammad Hosein Eghbali

2013-01-01

Full Text Available The oil content of the wax produced in a dewaxing process is the key economic parameter that should be reduced as much as possible. Some factors such as the type of solvents, cooling rate, temperature, and solvent to oil ratio influence the dewaxing process. Due to the fact that crude oil differs from place to place and since the operational conditions for wax extraction vary for different types of crude oil, the objective of this work is to study the operational conditions for wax production from an Iranian raffinate sample used in Sepahan Oil Company. All the experiments are conducted based on a design of experiment (DOE technique for minimizing the oil content of the wax produced. The effects of five factors have been determined quantitatively and appropriate levels are suggested for reducing the oil content. The results show that the solvent ratio, solvent composition, and cooling rate play the most important role in minimizing the oil content of the produced wax.

Structural-mechanical model of wax crystal networks—a mesoscale cellular solid approach

International Nuclear Information System (INIS)

Miyazaki, Yukihiro; Marangoni, Alejandro G

2014-01-01

Mineral waxes are widely used materials in industrial applications; however, the relationship between structure and mechanical properties is poorly understood. In this work, mineral wax-oil networks were characterized as closed-cell cellular solids, and differences in their mechanical response predicted from structural data. The systems studied included straight-chain paraffin wax (SW)-oil mixtures and polyethylene wax (PW)-oil mixtures. Analysis of cryogenic-SEM images of wax-oil networks allowed for the determination of the length (l) and thickness (t) of the wax cell walls as a function of wax mass fraction (Φ). A linear relationship between t/l and Φ (t/l ∼ Φ 0.89 ) suggested that wax-oil networks were cellular solids of the closed-cell type. However, the scaling behavior of the elastic modulus with the volume fraction of solids did not agree with theoretical predictions, yielding the same scaling exponent, μ = 0.84, for both waxes. This scaling exponent obtained from mechanical measurements could be predicted from the scaling behavior of the effective wax cell size as a function of wax mass fraction in oil obtained by cryogenic scanning electron microscopy. Microscopy studies allowed us to propose that wax-oil networks are structured as an ensemble of close-packed spherical cells filled with oil, and that it is the links between cells that yield under simple uniaxial compression. Thus, the Young’s moduli for the links between cells in SW and PW wax systems could be estimated as E L (SW) = 2.76 × 10 9 Pa and E L (PW) = 1.64 × 10 9 Pa, respectively. The structural parameter responsible for the observed differences in the mechanical strength between the two wax-oil systems is the size of the cells. Polyethylene wax has much smaller cell sizes than the straight chain wax and thus displays a higher Young’s modulus and yield stress. (papers)

Wax inhibitor based on ethylene vinyl acetate with methyl methacrylate and diethanolamine for crude oil pipeline

Science.gov (United States)

Anisuzzaman, S. M.; Abang, S.; Bono, A.; Krishnaiah, D.; Karali, R.; Safuan, M. K.

2017-06-01

Wax precipitation and deposition is one of the most significant flow assurance challenges in the production system of the crude oil. Wax inhibitors are developed as a preventive strategy to avoid an absolute wax deposition. Wax inhibitors are polymers which can be known as pour point depressants as they impede the wax crystals formation, growth, and deposition. In this study three formulations of wax inhibitors were prepared, ethylene vinyl acetate, ethylene vinyl acetate co-methyl methacrylate (EVA co-MMA) and ethylene vinyl acetate co-diethanolamine (EVA co-DEA) and the comparison of their efficiencies in terms of cloud point¸ pour point, performance inhibition efficiency (%PIE) and viscosity were evaluated. The cloud point and pour point for both EVA and EVA co-MMA were similar, 15°C and 10-5°C, respectively. Whereas, the cloud point and pour point for EVA co-DEA were better, 10°C and 10-5°C respectively. In conclusion, EVA co-DEA had shown the best % PIE (28.42%) which indicates highest percentage reduction of wax deposit as compared to the other two inhibitors.

Green diesel production via catalytic hydrogenation/decarboxylation of triglycerides and fatty acids of vegetable oil and brown grease

Science.gov (United States)

Sari, Elvan

Increase in the petroleum prices, projected increases in the world's energy demand and environmental awareness have shifted the research interest to the alternative fuel technologies. In particular, green diesel, vegetable oil/animal fat/waste oil and grease derived hydrocarbons in diesel boiling range, has become an attractive alternative to biodiesel---a mixture of fatty acid methyl esters, particularly due to its superior fuel properties that are similar to petroleum diesel. Hence, green diesel can be used as a drop-in fuel in the current diesel engines. The current technology for production of green diesel-hydrodeoxygenation of triglycerides and fatty acids over conventional hydrotreating catalysts suffers from fast catalyst deactivation in the absence of hydrogen combined with high temperatures and high fatty acid content in the feedstock. Additionally, excess hydrogen requirement for hydrodeoxygenation technique leads to high production costs. This thesis proposes a new technology-selective decarboxylation of brown grease, which is a mixture of fats and oils collected from waste water trap and rich in fatty acids, over a supported noble metal catalyst that overcomes the green diesel production challenges. In contrast to other feedstocks used for liquid biofuel production, brown grease is inexpensive and non-food competing feedstock, therefore the process finds solution to waste management issues, reduces the renewable fuel production cost and does not add to the global food shortage problems. Special catalyst formulations were developed to have a high activity and stability in the absence of hydrogen in the fatty acid decarboxylation process. The study shows how catalyst innovations can lead to a new technology that overcomes the process challenges. First, the effect of reaction parameters on the activity and the selectivity of brown grease decarboxylation with minimum hydrogen consumption over an activated carbon supported palladium catalyst were

A new experimental method to prevent paraffin - wax formation on the crude oil wells: A field case study in Libya

Directory of Open Access Journals (Sweden)

Elhaddad Elnori E.

2015-01-01

Full Text Available Wax formation and deposition is one of the most common problems in oil producing wells. This problem occurs as a result of the reduction of the produced fluid temperature below the wax appearance temperature (range between 46°C and 50°C and the pour point temperature (range between 42°C and 44°C. In this study, two new methods for preventing wax formation were implemented on three oil wells in Libya, where the surface temperature is, normally, 29°C. In the first method, the gas was injected at a pressure of 83.3 bar and a temperature of 65°C (greater than the pour point temperature during the gas-lift operation. In the second method, wax inhibitors (Trichloroethylene-xylene (TEX, Ethylene copolymers, and Comb polymers were injected down the casings together with the gas. Field observations confirmed that by applying these techniques, the production string was kept clean and no wax was formed. The obtained results show that the wax formation could be prevented by both methods.

Removal of colour, turbidity, oil and grease for slaughterhouse wastewater using electrocoagulation method

Science.gov (United States)

Yusoff, Mohd Suffian; Azwan, Azlyza Mohd; Zamri, Mohd Faiz Muaz Ahmad; Aziz, Hamidi Abdul

2017-10-01

In this study electrocoagulation method is used to treat slaughterhouse wastewaters. The aim of this study is to determine the efficiency of electrocoagulation method for the removal of colour, turbidity, oil and grease of slaughterhouse wastewaters. The factors of electrode types, and voltage applied during treatment are the study parameters. The types of electrode used are Aluminium (Al) grade 6082 and Iron (Fe) grade 1050. Meanwhile, the ranges of voltage applied are 2, 4, 6, 8 volts at a time interval of 10, 20 and 30 minutes respectively. The effect of these factors on the removal of fat oil and grease (FOG), colour and turbidity are analyzed. The results show maximum removal of FOG, colour and turbidity are recorded using Fe electrode at 8 V of applied voltage with 30 minutes of treatment time. The increase in treatment time of the cell will also increase the amount of hydrogen bubbles at the cathode which results in a greater upwards flux and a faster removal of FOG,, turbidity and colour. The removal of FOG, colour and turbidity are 98%, 92% and 91 % respectively. Meanwhile, by using Al electrodes in the same condition, the removal of FOG, colour and turbidity are 91%, 85% and 87 % respectively. Whereas by using Fe-Al as electrodes pairs, the removal of FOG, colour and turbidity are found to be at 90%, 87% and 76 % respectively. In this case, the Fe-Fe pair electrodes have been proven to provide better performance for FOG, colour and turbidity removals of slaughterhouse wastewaters. Therefore, it is feasible to be considered as an alternative method for wastewater treatment.

High-level accumulation of oleyl oleate in plant seed oil by abundant supply of oleic acid substrates to efficient wax ester synthesis enzymes.

Science.gov (United States)

Yu, Dan; Hornung, Ellen; Iven, Tim; Feussner, Ivo

2018-01-01

Biotechnology enables the production of high-valued industrial feedstocks from plant seed oil. The plant-derived wax esters with long-chain monounsaturated acyl moieties, like oleyl oleate, have favorite properties for lubrication. For biosynthesis of wax esters using acyl-CoA substrates, expressions of a fatty acyl reductase (FAR) and a wax synthase (WS) in seeds are sufficient. For optimization of the enzymatic activity and subcellular localization of wax ester synthesis enzymes, two fusion proteins were created, which showed wax ester-forming activities in Saccharomyces cerevisiae . To promote the formation of oleyl oleate in seed oil, WSs from Acinetobactor baylyi ( Ab WSD1) and Marinobacter aquaeolei ( Ma WS2), as well as the two created fusion proteins were tested in Arabidopsis to evaluate their abilities and substrate preference for wax ester production. The tested seven enzyme combinations resulted in different yields and compositions of wax esters. Expression of a FAR of Marinobacter aquaeolei ( Ma FAR) with Ab WSD1 or Ma WS2 led to a high incorporation of C 18 substrates in wax esters. The Ma FAR/TM Mm AWAT2- Ab WSD1 combination resulted in the incorporation of more C 18:1 alcohol and C 18:0 acyl moieties into wax esters compared with Ma FAR/ Ab WSD1. The fusion protein of a WS from Simmondsia chinensis ( Sc WS) with MaFAR exhibited higher specificity toward C 20:1 substrates in preference to C 18:1 substrates. Expression of Ma FAR/ Ab WSD1 in the Arabidopsis fad2 fae1 double mutant resulted in the accumulation of oleyl oleate (18:1/18:1) in up to 62 mol% of total wax esters in seed oil, which was much higher than the 15 mol% reached by Ma FAR/ Ab WSD1 in Arabidopsis Col-0 background. In order to increase the level of oleyl oleate in seed oil of Camelina , lines expressing Ma FAR/ Sc WS were crossed with a transgenic high oleate line. The resulting plants accumulated up to >40 mg g seed -1 of wax esters, containing 27-34 mol% oleyl oleate. The

Pickering emulsions stabilized by paraffin wax and Laponite clay particles.

Science.gov (United States)

Li, Caifu; Liu, Qian; Mei, Zhen; Wang, Jun; Xu, Jian; Sun, Dejun

2009-08-01

Emulsions containing wax in dispersed droplets stabilized by disc-like Laponite clay particles are prepared. Properties of the emulsions prepared at different temperatures are examined using stability, microscopy and droplet-size analysis. At low temperature, the wax crystals in the oil droplets can protrude through the interface, leading to droplet coalescence. But at higher temperatures, the droplet size decreases with wax concentration. Considering the viscosity of the oil phase and the interfacial tension, we conclude that the wax is liquid-like during the high temperature emulsification process, but during cooling wax crystals appear around the oil/water interface and stabilize the droplets. The oil/water ratio has minimal effect on the emulsions between ratios of 3:7 and 7:3. The Laponite is believed to stabilize the emulsions by increasing the viscosity of the continuous phase and also by adsorbing at the oil/water interface, thus providing a physical barrier to coalescence.

Effects of the free fatty acid content in yellow grease on performance, carcass characteristics, and serum lipids in broilers.

Science.gov (United States)

Wu, H; Gong, L M; Guo, L; Zhang, L Y; Li, J T

2011-09-01

This study was conducted to investigate whether the free fatty acid (FFA) content of yellow grease would influence the performance and carcass characteristics of broiler chicks. A total of 432 one-day-old, male Arbor Acres broilers were randomly allotted to 1 of 4 treatments, with each treatment being applied to 6 pens of 18 chicks. The dietary treatments were based on corn and soybean meal and were supplemented with either soybean oil (2.86% FFA) or yellow grease with a low (2.74%), medium (12.59%), or high (19.05%) FFA content. The fat sources were supplemented at 1.5% of the diet during the starter phase (0 to 21 d) and at 3.0% of the diet during the grower phase (22 to 42 d). From d 0 to 42, the BW gains of chicks fed diets containing soybean oil and yellow grease with 2.74% FFA were similar. As the FFA level in the yellow grease increased, the BW gain of chicks decreased (P dressing percentage and the percentage of breast muscle in the carcass were significantly (P < 0.01) lower for broilers fed any yellow grease diet compared with birds fed soybean oil. In contrast, abdominal fat was significantly increased in diets containing yellow grease. These results demonstrate that the performance of birds fed yellow grease with a low content of FFA was essentially equal to that of birds fed soybean oil. However, because yellow grease samples containing FFA levels greater than 2.74% negatively affected bird performance, producers should exercise caution with regard to feeding broilers yellow grease with an elevated FFA content. In 42-d-old broilers, serum total cholesterol and low-density lipoprotein cholesterol levels were elevated in birds fed yellow grease, regardless of the dietary level. In contrast, serum high-density lipoprotein cholesterol and triglyceride levels were unaffected by dietary treatment. Although dietary FFA may influence triglyceride-rich lipoprotein metabolism in broilers, an explanation for the observed effects remains elusive.

Effects of Hydrocarbon-Based Grease on Rapid Prototype Material Used for Grease Retention Shrouds

Science.gov (United States)

Zakrajsek, Andrew J.; Valco, Daniel J.; Street, Kenneth W., Jr.

2010-01-01

Effects of hydrocarbon-based greases on specific rapid prototype (RP) materials used to fabricate grease retention shrouds (GRS) were explored in this study. Grease retention shrouds are being considered as a way to maintain adequate grease lubrication at the gear mesh in a prototype research transmission system. Due to their design and manufacturing flexibility, rapid prototype materials were chosen for the grease retention shrouds. In order to gain a better understanding of the short and long term effects grease pose on RP materials, research was conducted on the interaction of hydrocarbon-based grease with RP materials. The materials used in this study were durable polyamide (nylon), acrylonitrile butadiene styrene (ABS), and WaterClear 10120. Testing was conducted using Mobilgrease 28 and Syn-Tech 3913G grease (gear coupling grease). These greases were selected due to their regular use with mechanical components. To investigate the effect that grease has on RP materials, the following methods were used to obtain qualitative and quantitative data: Fourier transform infrared spectroscopy (FT-IR), interference profilometer measurements, digital camera imaging, physical shape measurement, and visual observations. To record the changes in the RP materials due to contact with the grease, data was taken before and after the grease application. Results showed that the WaterClear 10120 RP material provided the best resistance to grease penetration as compared to nylon and ABS RP materials. The manufacturing process, and thus resulting surface conditions of the RP material, played a key role in the grease penetration properties and resilience of these materials.

Design and application on experimental platform for high-speed bearing with grease lubrication

Directory of Open Access Journals (Sweden)

He Qiang

2015-12-01

Full Text Available The experimental platform for high-speed grease is an important tool for research and development of high-speed motorized spindle with grease lubrication. In this article, the experimental platform for high-speed grease is designed and manufactured which consists of the drive system, the test portion, the loading system, the lubrication system, the control system, and so on. In the meantime, the high-speed angular contact ceramic ball bearings B7005C/HQ1P4 as the research object are tested and contrasted in the grease lubrication and oil mist lubrication. The experimental platform performance is validated by contrast experiment, and the high-speed lubricated bearing performance is also studied especially in the relationship among the rotating speed,load and temperature rise. The results show that the experimental platform works steadily, accurate, and reliable in the experimental testing. And the grease lubrication ceramic ball bearings B7005C/HQ1P4 can be used in high-speed motorized spindle in the circular water cooling conditions when the rotating speed is lower than 40,000 r/min or the DN value (the value of the bearing diameter times the rotating speed is lower than the 1.44 × 106 mm r/min. Grease lubrication instead of oil mist lubrication under high-speed rotating will simplify the structure design of the high-speed motorized spindle and reduce the pollution to the environment.

Irradiation effect study on dynamic performance of grease

International Nuclear Information System (INIS)

Arakawa, Kazuo; Sasuga, Tsuneo; Hagiwara, Miyuki; Yajima, Toshio; Nakanishi, Hiroshi; Soda, Takao; Iwamoto, Takeshi.

1986-03-01

The radiation resistance of newly developed grease, MORESCO HIRAD RG-42-0, consisting of polyphenyl ether as base oil and inorganic compound as gelling agent was evaluated by conducting measurements of frictional resistance force on mechanical snubbers. After the irradiation of 60 Co γ-rays up to a predetermined dose [max. 100 MGy (10000 Mrad)], the grease was applied to mechanical snubbers. The rated load of mechanical snubbers used (standard stroke of 125 mm) was set at 0.16 ton and 1.0 ton. The frictional resistance force was measured at a velocity of 0.001, 0.01, 0.1 and 2.0 mm/sec and at temperature of 60 deg C. When the rated load was 0.16 ton, the frictional resistance force of irradiated grease was kept less than a criterion, a greater value of either 5 kgf or 1 % of the rated load, at every tested dose up to 90 MGy. In case of 1.0 ton, the frictional resistance force of the irradiated grease was less than a greater value of either 10 kgf or 1 % of the rated load at doses up to 70 MGy. (author)

The Use of Biobased Surfactant Obtained by Enzymatic Syntheses for Wax Deposition Inhibition and Drag Reduction in Crude Oil Pipelines

Directory of Open Access Journals (Sweden)

Zhihua Wang

2016-04-01

Full Text Available Crude oil plays an important role in providing the energy supply of the world, and pipelines have long been recognized as the safest and most efficient means of transporting oil and its products. However, the transportation process also faces the challenges of asphaltene-paraffin structural interactions, pipeline pressure losses and energy consumption. In order to determine the role of drag-reducing surfactant additives in the transportation of crude oils, experiments of wax deposition inhibition and drag reduction of different oil in pipelines with a biobased surfactant obtained by enzymatic syntheses were carried out. The results indicated that heavy oil transportation in the pipeline is remarkably enhanced by creating stable oil-in-water (O/W emulsion with the surfactant additive. The wax appearance temperature (WAT and pour point were modified, and the formation of a space-filling network of interlocking wax crystals was prevented at low temperature by adding a small concentration of the surfactant additive. A maximum viscosity reduction of 70% and a drag reduction of 40% for light crude oil flows in pipelines were obtained with the surfactant additive at a concentration of 100 mg/L. Furthermore, a successful field application of the drag-reducing surfactant in a light crude oil pipeline in Daqing Oilfield was demonstrated. Hence, the use of biobased surfactant obtained by enzymatic syntheses in oil transportation is a potential method to address the current challenges, which could result in a significant energy savings and a considerable reduction of the operating cost.

Isolation of Bacterial Strain for Biodegradation of Fats, Oil and Grease

International Nuclear Information System (INIS)

Alkhatib, M.F.; Mohd Zahangir Alam; Shabana, H.F.M.

2015-01-01

Fat, oil and grease (FOG) deposition is one of the major problems that harm the environment and cause dissatisfaction for human. Uncontrolled and un-pre-treated FOG removal from the kitchen could lead to its accumulation in the piping system. Problems include the interference of fat with the aerobic microorganisms that are responsible in treating the wastewater by reducing oxygen transfer rates and for anaerobic microorganisms; their efficiency could also be reduced due to the reduction of the transport of soluble substrates to the bacterial biomass. Biodegradation could be one of the effective means to treat FOG. The main objective of this study is to isolate bacterial strains from the FOG waste and identify the strains that are capable in biodegrading FOG waste. FOG sample was collected from a sewer manhole. Enrichment technique was applied, followed by isolation of bacterial strains to determine which strain is able to degrade the FOG deposition. Some morphology for the bacterial strain was done to determine its characteristics. (author)

Handbook of vacuum physics

CERN Document Server

1964-01-01

Handbook of Vacuum Physics, Volume 3: Technology is a handbook of vacuum physics, with emphasis on the properties of miscellaneous materials such as mica, oils, greases, waxes, and rubber. Accurate modern tables of physical constants, properties of materials, laboratory techniques, and properties of commercial pumps, gauges, and leak detectors are presented. This volume is comprised of 12 chapters and begins with a discussion on pump oils, divided into rotary pump oils and vapor pump oils. The next chapter deals with the properties and applications of greases, including outgassing and vapor pr

Problems, control, and treatment of fat, oil, and grease (FOG): a review.

Science.gov (United States)

Husain, Iman A F; Alkhatib, Ma'an Fahmi; Jammi, Mohamed Saedi; Mirghani, Mohamed E S; Bin Zainudin, Zaki; Hoda, Asif

2014-01-01

Presence of fat, oil, and grease (FOG) in wastewater is an ever-growing concern to municipalities and solid-waste facility operators. FOG enters the sewer system from restaurants, residences, and industrial food facilities. Its release into the sewer system results in a continuous build-up that causes eventual blockage of sewer pipes. Several researchers have investigated FOG deposition based on the local conditions of sewers and lifestyle. This paper attempts to review the physical and chemical characteristics of FOG, sources of FOG, and potential chemical and biological reactions of FOG. The effect of the aforementioned factors on the FOG-deposition mechanism is also discussed. Moreover, insight into the current control and treatment methods and potential reuse of FOG is highlighted. It is expected that this review would provide scientists and the concerned authorities a holistic view of the recent researches on FOG control, treatment, and reuse.

Oil and grease (O&G) removal from commercial kitchen waste water using carbonised grass as a key media

OpenAIRE

Rahmat Siti Nazahiyah; Mohd Ali Ahmad Zurisman; Wan Ibrahim Mohd Haziman; Alias Nur Azrena

2017-01-01

Oil and grease (O&G) are usually found in kitchen waste water. O&G are poorly soluble in water and can cause serious problems during the wastewater treatment. Adsorption is a fundamental process in the treatment of kitchen waste water and very economical. Activated carbon is the most effective adsorbent for this application. Therefore, the aim of the current study is to determine the potential of four materials (i.e. sand, gravel, carbonised grass (CG) and clay powder) as filter media for O&G...

Organically modified clay removes oil from water

International Nuclear Information System (INIS)

Alther, G.R.

1995-01-01

When bentonite or other clays and zeolite are modified with quaternary amines, they become organophilic. Such modified bentonites are used to remove mechanically emulsified oil and grease, and other sparingly soluble organics. Types of oil found in water can include fats, lubricants, cutting fluids, heavy hydrocarbons such as tars, grease, crude oil, diesel oils; and light hydrocarbons such as kerosene, jet fuel, and gasoline. If the organoclay is granulated, it is placed into a liquid phase carbon filter vessel to remove FOGs (Free Oil and Grease) and chlorinated hydrocarbons. In this application the clay is mixed with anthrazite to prevent early plugging of the filter by oil or grease droplets. In batch systems a powdered organoclay is employed. Organoclay removes mechanically emulsified oil and grease at 5--7 times the rate of activated carbon, or 50% of its dry weight. Oil and grease and other large sparingly soluble chlorinated hydrocarbons and NOMs (Natural Organic Matter) blind the pores of activated carbon (and ion-exchange resins), reducing its effectiveness significantly. It is therefore economically advantageous for the end user to prepolish the water before it enters carbon vessels. Operating costs can often be reduced by 50% or more

Grease lubrication in rolling bearings

CERN Document Server

Lugt, Piet M

2012-01-01

The definitive book on the science of grease lubrication for roller and needle bearings in industrial and vehicle engineering. Grease Lubrication in Rolling Bearings provides an overview of the existing knowledge on the various aspects of grease lubrication (including lubrication systems) and the state of the art models that exist today. The book reviews the physical and chemical aspects of grease lubrication, primarily directed towards lubrication of rolling bearings. The first part of the book covers grease composition, properties and rheology, including thermal

NEW RADIATION RESISTANT GREASES

Energy Technology Data Exchange (ETDEWEB)

DasGupta, Sharda; Slobodian, J. T.

1962-11-20

New radiation resistant greases were prepared from commercially available greases by carrying out radioinduced reactions with styrene. The radiation tolerances of the products were 250-1000 fold more than the starting materials and any product of similar properties now available. The various properties of the new products initially and after exposure to large radiation doses were in no case inferior to the original greases and in some respects improvements were observed. Radiation tolerance of commercial greases could be enhanced by the addition of polystyrene to form a physical mixture rather than copolymers. The reaction mechanisms involved at all stages were studied using infrared spectroscopic techniques. (P.C.H.)

Evidence for fat, oil, and grease (FOG) deposit formation mechanisms in sewer lines.

Science.gov (United States)

He, Xia; Iasmin, Mahbuba; Dean, Lisa O; Lappi, Simon E; Ducoste, Joel J; de los Reyes, Francis L

2011-05-15

The presence of hardened and insoluble fats, oil, and grease (FOG) deposits in sewer lines is a major cause of line blockages leading to sanitary sewer overflows (SSOs). Despite the central role that FOG deposits play in SSOs, little is known about the mechanisms of FOG deposit formation in sanitary sewers. In this study, FOG deposits were formed under laboratory conditions from the reaction between free fatty acids and calcium chloride. The calcium and fatty acid profile analysis showed that the laboratory-produced FOG deposit displayed similar characteristics to FOG deposits collected from sanitary sewer lines. Results of FTIR analysis showed that the FOG deposits are metallic salts of fatty acid as revealed by comparisons with FOG deposits collected from sewer lines and pure calcium soaps. Based on the data, we propose that the formation of FOG deposits occurs from the aggregation of excess calcium compressing the double layer of free fatty acid micelles and a saponification reaction between aggregated calcium and free fatty acids.

Influence of fat and oil type on the yield, physico-chemical properties, and microstructure of fat, oil, and grease (FOG) deposits.

Science.gov (United States)

Del Mundo, Dann Marie N; Sutheerawattananonda, Manote

2017-11-01

Fat, oil, and grease (FOG) deposit, in the form of calcium soap, was found to cause sanitary sewer overflows due to its adhesion on pipe walls. To address this problem, laboratory-prepared calcium soaps have been used to investigate the formation mechanisms of FOG deposits. However, the fats and oils previously utilized were limited and some soap characteristics were not examined. This research attempted to probe through the properties of calcium soaps prepared from calcium chloride and the fats and oils of chicken, pork, palm olein, soybean, olive, and coconut to further understand FOG formation and stability. Results revealed that FOG deposits may occur as smooth, paste-like material or coarse, semi-solid substance depending on their exposure to excess fat/oil and calcium. The smooth soaps with more excess fat/oil demonstrated high apparent viscosity and consistency index, while the coarse soaps with large levels of calcium signified higher melting endset. Moreover, a soap microstructure showing evident networks and lesser void area displayed higher heat and rheological stability, respectively. Overall, fats and oils with higher oleic to palmitic acid ratio such as palm olein oil, olive oil, chicken fat, and pork fat produced soaps with greater yield and degree of saponification. Hence, establishments and authorities should be alert in managing and monitoring these wastes. On the other hand, soybean oil high in linoleic acid and coconut oil high in lauric acid do not pose an immediate threat to the sewer system since they only produced soaps in small quantity. However, their soaps showed high melting endset which could pose a serious effect when accumulated at large amount. On the whole, the fatty acid profile of fats and oils, the presence of excess fat/oil, and calcium content mainly dictate the appearance, melting, rheology, and microstructure of calcium soaps. Their distinct properties can be used as criteria in predicting the condition and stability of FOG

Wax-incorporated emulsion gel beads of calcium pectinate for intragastric floating drug delivery.

Science.gov (United States)

Sriamornsak, Pornsak; Asavapichayont, Panida; Nunthanid, Jurairat; Luangtana-Anan, Manee; Limmatvapirat, Sontaya; Piriyaprasarth, Suchada

2008-01-01

The purpose of this study was to prepare wax-incorporated pectin-based emulsion gel beads using a modified emulsion-gelation method. The waxes in pectin-olive oil mixtures containing a model drug, metronidazole, were hot-melted, homogenized and then extruded into calcium chloride solution. The beads formed were separated, washed with distilled water and dried for 12 h. The influence of various types and amounts of wax on floating and drug release behavior of emulsion gel beads of calcium pectinate was investigated. The drug-loaded gel beads were found to float on simulated gastric fluid if the sufficient amount of oil was used. Incorporation of wax into the emulsion gel beads affected the drug release. Water-soluble wax (i.e. polyethylene glycol) increased the drug release while other water-insoluble waxes (i.e. glyceryl monostearate, stearyl alcohol, carnauba wax, spermaceti wax and white wax) significantly retarded the drug release. Different waxes had a slight effect on the drug release. However, the increased amount of incorporated wax in the formulations significantly sustained the drug release while the beads remained floating. The results suggest that wax-incorporated emulsion gel beads could be used as a carrier for intragastric floating drug delivery.

Preliminary experimental research to detect grease stain of petroleum pipeline by sup 1 sup 3 sup 7 Cs gamma-ray transmission method

CERN Document Server

Wang Shi Heng

2002-01-01

The experimental study on the detection of grease stain for petroleum pipeline in Karamay oil-field of Xinjiang is carried out by gamma-ray transmission method. Experimental provision consists of sup 1 sup 3 sup 7 Cs gamma radiator and NaI(Tl) scintillation detector. The response of grease stain thickness of petroleum pipeline in Karamay oil-field is ln(N sub 0 /N)=0.00548 d-0.0046, and the response of paraffin thickness is ln(N sub 0 /N)=0.00522d-0.0126. The result of experiment indicates that the response of grease stain thickness is more sensitive than the response of paraffin thickness

CARNAUBA WAX USED AS AN HYDROPHOBIC AGENT FOR EXPANDED VERMICULITE

Directory of Open Access Journals (Sweden)

M.A.F. Melo

1998-03-01

Full Text Available This work deals with the use of carnauba wax as an expansion and hydrophobicity agent for vermiculite, to be utilized in the sorption process of oil in water. Evaluation of the system (oil-water-hydrophobic vermiculite submersion percentage was considered in assessing the performance of vermiculite in comparison to a Mexican turf. Carnauba wax seems to be more efficient in both fresh and salt waters.

Wax Point Determinations Using Acoustic Resonance Spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Bostick, D.T.; Jubin, R.T.; Schmidt, T.W.

2001-06-01

The thermodynamic characterization of the wax point of a given crude is essential in order to maintain flow conditions that prevent plugging of undersea pipelines. This report summarizes the efforts made towards applying an Acoustic Cavity Resonance Spectrometer (ACRS) to the determination of pressures and temperatures at which wax precipitates from crude. Phillips Petroleum Company, Inc., the CRADA participant, supplied the ACRS. The instrumentation was shipped to Dr. Thomas Schmidt of ORNL, the CRADA contractor, in May 2000 after preliminary software development performed under the guidance of Dr. Samuel Colgate and Dr. Evan House of the University of Florida, Gainesville, Fl. Upon receipt it became apparent that a number of modifications still needed to be made before the ACRS could be precisely and safely used for wax point measurements. This report reviews the sequence of alterations made to the ACRS, as well as defines the possible applications of the instrumentation once the modifications have been completed. The purpose of this Cooperative Research and Development Agreement (CRADA) between Phillips Petroleum Company, Inc. (Participant) and Lockheed Martin Energy Research Corporation (Contractor) was the measurement of the formation of solids in crude oils and petroleum products that are commonly transported through pipelines. This information is essential in the proper design, operation and maintenance of the petroleum pipeline system in the United States. Recently, new petroleum discoveries in the Gulf of Mexico have shown that there is a potential for plugging of undersea pipeline because of the precipitation of wax. It is important that the wax points of the expected crude oils be well characterized so that the production facilities for these new wells are capable of properly transporting the expected production. The goal of this work is to perform measurements of solids formation in crude oils and petroleum products supplied by the Participant. It is

Purification of a jojoba embryo wax synthase, cloning of its cDNA, and production of high levels of wax in seeds of transgenic arabidopsis.

Science.gov (United States)

Lardizabal, K D; Metz, J G; Sakamoto, T; Hutton, W C; Pollard, M R; Lassner, M W

2000-03-01

Wax synthase (WS, fatty acyl-coenzyme A [coA]: fatty alcohol acyltransferase) catalyzes the final step in the synthesis of linear esters (waxes) that accumulate in seeds of jojoba (Simmondsia chinensis). We have characterized and partially purified this enzyme from developing jojoba embryos. A protein whose presence correlated with WS activity during chromatographic fractionation was identified and a cDNA encoding that protein was cloned. Seed-specific expression of the cDNA in transgenic Arabidopsis conferred high levels of WS activity on developing embryos from those plants. The WS sequence has significant homology with several Arabidopsis open reading frames of unknown function. Wax production in jojoba requires, in addition to WS, a fatty acyl-CoA reductase (FAR) and an efficient fatty acid elongase system that forms the substrates preferred by the FAR. We have expressed the jojoba WS cDNA in Arabidopsis in combination with cDNAs encoding the jojoba FAR and a beta-ketoacyl-CoA synthase (a component of fatty acid elongase) from Lunaria annua. (13)C-Nuclear magnetic resonance analysis of pooled whole seeds from transgenic plants indicated that as many as 49% of the oil molecules in the seeds were waxes. Gas chromatography analysis of transmethylated oil from individual seeds suggested that wax levels may represent up to 70% (by weight) of the oil present in those seeds.

Urban Waste Grease Resource Assessment

Energy Technology Data Exchange (ETDEWEB)

Wiltsee, G.

1999-03-17

This study collected and analyzed data on urban waste grease resources in 30 randomly selected metropolitan areas in the United States. Two major categories (yellow grease feedstock collected from restaurants by rendering companies; and grease trap wastes from restaurants, which can either be pumped into tank trucks for disposal or flow through municipal sewage systems into wastewater treatment plants) were considered in this study.

Quantifying fat, oil, and grease deposit formation kinetics.

Science.gov (United States)

Iasmin, Mahbuba; Dean, Lisa O; Ducoste, Joel J

2016-01-01

Fat, oil, and grease (FOG) deposits formed in sanitary sewers are calcium-based saponified solids that are responsible for a significant number of nationwide sanitary sewer overflows (SSOs) across United States. In the current study, the kinetics of lab-based saponified solids were determined to understand the kinetics of FOG deposit formation in sewers for two types of fat (Canola and Beef Tallow) and two types of calcium sources (calcium chloride and calcium sulfate) under three pH (7 ± 0.5, 10 ± 0.5, and ≈14) and two temperature conditions (22 ± 0.5 and 45 ± 0.5 °C). The results of this study displayed quick reactions of a fraction of fats with calcium ions to form calcium based saponified solids. Results further showed that increased palmitic fatty acid content in source fats, the magnitude of the pH, and temperature significantly affect the FOG deposit formation and saponification rates. The experimental data of the kinetics were compared with two empirical models: a) Cotte saponification model and b) Foubert crystallization model and a mass-action based mechanistic model that included alkali driven hydrolysis of triglycerides. Results showed that the mass action based mechanistic model was able to predict changes in the rate of formation of saponified solids under the different experimental conditions compared to both empirical models. The mass-action based saponification model also revealed that the hydrolysis of Beef Tallow was slower compared to liquid Canola fat resulting in smaller quantities of saponified solids. This mechanistic saponification model, with its ability to track the saponified solids chemical precursors, may provide an initial framework to predict the spatial formation of FOG deposits in municipal sewers using system wide sewer collection modeling software. Copyright © 2015 Elsevier Ltd. All rights reserved.

Propiedades fisicoquímicas y tribológicas de una grasa grafitada de Jatropha curcas L y jabón de litio//Physicochemical and tribological properties of graphite grease based on Jatrophacurcas L oil and lithium soap

Directory of Open Access Journals (Sweden)

Juliano‐Chitue de Assunção‐Nascimento

2014-08-01

Full Text Available Las grasas lubricantes son consideradas una dispersión coloidal de un espesante en un fluido lubricante. Los aceites vegetales son ampliamente usados en muchas formulaciones de grasas. En este trabajo se determinaron las propiedades fisicoquímicas y tribológicas de una grasa lubricante fabricada con aceite vegetal de Jatropha curcas L y jabón de litio (JC1G5. Alfa tocoferol acetato y grafito fueron usados como aditivos antioxidante y de extrema presión respectivamente. La grasa JC1G5 mostró un color negro, una temperatura de goteo de 140 oC, apropiadas propiedades de corrosión al cobre y un grado de consistencia NLGI Grado1. El efecto de la lubricación de la grasa JC1G5 fue probado, empleando una máquina de cuatro bolas y un tribómetro timken. Los resultados indican que la grasa JC1G5 posee propiedades tribológicas comparables con una grasa mineral de jabón de litio.Palabras claves: grasa, jatropha curcas L, jabón de litio, propiedades fisicoquímicas, propiedades tribológicas.______________________________________________________________________________AbstractLubricating greases are considered as colloidal dispersions of a thickener in a lubricating fluid. The vegetable oils are widely used in many formulations of greases. In this paper were determined the physicochemical and tribological properties of graphite grease based on Jatropha curcas L vegetableoil and lithium soap (JC1G5. Alpha tocofherol acetate and graphite were used as antioxidant and extreme pressure additives respectively. The grease JC1G5 showed a black color, a dropping point of 140 oC, appropriate magnitude of copper corrosion and consistency NLGI Grade 1. Lubrication performance of the grease JC1G5 was tested using the 4-ball wear tester and timken tribometer tester. Results indicate that the grease JC1G5 has tribological properties comparable to that of mineral oil base lithium grease.Key words: grease, jatrophacurcas L, lithium soap, physicochemical

Online estimation of wax deposition thickness in single-phase sub-sea pipelines based on acoustic chemometrics: A feasibility study

OpenAIRE

Halstensen, Maths; Arvoh, Benjamin Kaku; Amundsen, Lene; Hoffmann, Rainer

2012-01-01

Wax deposition in sub-sea oil producing pipelines is a concern to the oil producing companies. The deposition of wax in pipelines can cause serious economic implications if not monitored and controlled. Several researchers have developed models and investigated the deposition of wax in crude oil pipelines. As of today, there is no off the shelf instrument available for reliable online estimation of the wax depo- sition thickness in sub-sea pipelines. Acoustic chemometrics was applied to inves...

Surfactants and Desensitizing Wax Substitutes for TNT-Based Systems.

Science.gov (United States)

1994-10-01

greatly with the source of crude oil. Some crudes contain little wax. The U.S. crudes from Pennsylvania and the midcontinent areas contain high...years ago in Egypt for many different purposes. The term wax comes to us from the Anglo-Saxon "weax," the name given to material from the bee ...usually produced in the wild and not by large scale cultivation. Although plants produce small amounts of waxes in their tissues, seeds and pollen

Physico-chemical characterization of grease interceptors with and without biological product addition.

Science.gov (United States)

He, Xia; Osborne, Jason; de los Reyes, Francis L

2012-03-01

Hardened and insoluble fat, oil, and grease (FOG) deposits are the primary cause of sewer line blockages leading to sanitary sewer overflows (SSOs). However, there have been very few long-term assessments of the physico-chemical characteristics of full-scale grease interceptors (GIs), the first "line of defense" against FOG buildup in sewer lines. In this study, we assessed the physico-chemical characteristics of two full-scale GIs (at a restaurant and a retirement community kitchen) over a one-year period. Statistically significant differences between bioaugmented and untreated cycles were detected for several chemical and physical properties. The treated cycles had lower BOD and COD at the grease interceptor outlet. While the combined data for all treated cycles did not show lower FOG concentrations in the GI outlet compared to the combined data for all untreated cycles, comparison of specific individual treated and untreated cycles show a positive effect due to the addition of product.

Real-time monitoring and measurement of wax deposition in pipelines via non-invasive electrical capacitance tomography

Science.gov (United States)

Lock Sow Mei, Irene; Ismail, Idris; Shafquet, Areeba; Abdullah, Bawadi

2016-02-01

Tomographic analysis of the behavior of waxy crude oil in pipelines is important to permit appropriate corrective actions to be taken to remediate the wax deposit layer before pipelines are entirely plugged. In this study, a non-invasive/non-intrusive electrical capacitance tomography (ECT) system has been applied to provide real-time visualization of the formation of paraffin waxes and to measure the amount of wax fraction from the Malay Basin waxy crude oil sample under the static condition. Analogous expressions to estimate the wax fraction of the waxy crude oil across the temperatures range of 30-50 °C was obtained by using Otsu’s and Kuo’s threshold algorithms. Otsu’s method suggested that the wax fraction can be estimated by the correlation coefficient β =0.0459{{T}3}-5.3535{{T}2}+200.36T-2353.7 while Kuo’s method provides a similar correlation with β =0.0741{{T}3}-8.4915{{T}2}+314.96T-3721.2 . These correlations show good agreements with the results which are obtained from the conventional weighting method. This study suggested that Kuo’s threshold algorithm is more promising when integrated into the ECT system compared to Otsu’s algorithm because the former provides higher accuracy wax fraction measurement results below the wax appearance temperature for waxy crude oil. This study is significant because it serves as a preliminary investigation for the application of ECT in the oil and gas industry for online measurement and detection of wax fraction without causing disturbance to the process flow.

Organically modified clay removes oil from water

International Nuclear Information System (INIS)

Alther, G.R.

1995-01-01

When bentonite or other clays and zeolites are modified with quaternary amines, they become organophilic. Such modified bentonites are used to remove mechanically emulsified oil and grease, and other sparingly soluble organics. If the organoclay is granulated, it is placed into a liquid phase carbon filter vessel to remove FOG's and chlorinated hydrocarbons. In this application the clay is mixed with anthrazite to prevent early plugging of the filter by oil or grease droplets. In batch systems a powered organoclay is employed. Types of oil found in water can include fats, lubricants, cutting fluids, heavy hydrocarbons such as tars, grease, crude oil, diesel oils; and light hydrocarbons such as kerosene, jet fuel, and gasoline

Fat, oil and grease deposits in sewers: characterisation of deposits and formation mechanisms.

Science.gov (United States)

Williams, J B; Clarkson, C; Mant, C; Drinkwater, A; May, E

2012-12-01

Fat, oil and grease deposits (FOG) in sewers are a major problem and can cause sewer overflows, resulting in environmental damage and health risks. Often simplistically portrayed as cooling of fats, recent research has suggested that saponification may be involved in FOG formation. However there are still questions about the mechanisms effecting transformations in sewers and the role and source of metal cations involved in saponification. This study characterises FOG deposits from pumping stations, sewers and sewage works from different water hardness zones across the UK. The sites all had previous problems with FOG and most catchments contained catering and food preparation establishments. The FOG deposits were highly variable with moisture content ranging from 15 to 95% and oil content from 0 to 548 mg/g. Generally the pumping stations had lower moisture content and higher fat content, followed by the sewers then the sewage works. The water in contact with the FOG had high levels of oil (mean of about 800 mg/L) and this may indicate poor kitchen FOG management practices. FOG fatty acid profiles showed a transformation from unsaturated to saturated forms compared to typical cooking oils. This seems to relate to ageing in the sewer network or the mechanism of formation, as samples from pumping stations had higher proportions of C18:1 compared to C16. This may be due to microbial transformations by bacteria such as Clostridium sp. in a similar process to adipocere formation. There was an association between water hardness and increased Ca levels in FOG along with harder deposits and higher melting points. A link between FOG properties and water hardness has not been previously reported for field samples. This may also be due to microbial processes, such as biocalcification. By developing the understanding of these mechanisms it may be possible to more effectively control FOG deposits, especially when combined with promotion of behavioural change. Copyright © 2012

Oleogels of virgin olive oil with carnauba wax and monoglyceride as spreadable products

Directory of Open Access Journals (Sweden)

Öǧütcü, M.

2014-09-01

Full Text Available The oleogels of virgin olive oil with carnauba wax and monoglyceride were prepared to determine the most suitable spreadable product. The oil binding capacities of monoglyceride oleogels were higher than those of the carnauba wax oleogels. There was no true crystalline structure with carnauba wax at 3%. Although the highest solid fat content was in the 10% monoglyceride oleogel (9.38%, it was 12.15% in the commercial breakfast margarine at 20 °C. The peak melting temperature of the margarine was 47.11 °C, and among all oleogels, monoglyceride oleogel at 7% addition had the closest value (48.70 °C. The melting enthalpies of the oleogels ranged from 1.25 to 103.97 J·g−1, while it was 94.19 J·g−1 for the margarine sample. The firmness and stickiness values were usually lower in the oleogel samples than those of the margarine sample. There was no significant change in the texture parameters during storage, indicating good structural stability. The polarized light microscopy pictures revealed rod-like crystals for carnauba wax and rosette-like aggregates for monoglyceride oleogels. X-ray diffraction patterns of the samples have revealed a β´-type polymorphic structure for the oleogels. These oleogels can be used in a spreadable, breakfast margarin-like product to promote new consumption habits for this healthy oil.Se prepararon oleogeles de aceites de oliva virgen con cera de carnaúba y monoglicéridos para encontrar el producto más adecuado para untar. La capacidad de unión de aceites de oleogeles de monoglicéridos fue más alto que el de los oleogeles de cera de carnaúba. No hubo ninguna estructura cristalina verdadera con cera de carnaúba al 3%. Aunque el mayor contenido de grasa sólida fue con el 10 % de oleogeles de monoglicérido (9,38 %, fue del 12.15 % en el de margarina comercial a 20 °C. La temperatura pico de fusión de la margarina fue 47,11 ºC, y entre todos los oleogeles, los de monoglicérido al 7 % tuvo el valor m

Dual-fuel production from restaurant grease trap waste: bio-fuel oil extraction and anaerobic methane production from the post-extracted residue.

Science.gov (United States)

Kobayashi, Takuro; Kuramochi, Hidetoshi; Maeda, Kouji; Tsuji, Tomoya; Xu, Kaiqin

2014-10-01

An effective way for restaurant grease trap waste (GTW) treatment to generate fuel oil and methane by the combination of physiological and biological processes was investigated. The heat-driven extraction could provide a high purity oil equivalent to an A-grade fuel oil of Japanese industrial standard with 81-93 wt% of extraction efficiency. A post-extracted residue was treated as an anaerobic digestion feedstock, and however, an inhibitory effect of long chain fatty acid (LCFA) was still a barrier for high-rate digestion. From the semi-continuous experiment fed with the residual sludge as a single substrate, it can be concluded that the continuous addition of calcium into the reactor contributed to reducing LCFA inhibition, resulting in the long-term stable operation over one year. Furthermore, the anaerobic reactor performed well with 70-80% of COD reduction and methane productivity under an organic loading rate up to 5.3g-COD/L/d. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development and evaluation of emulsifying systems of the material grease from Brazilian flora

Directory of Open Access Journals (Sweden)

Douglas Dourado

2015-10-01

Full Text Available Context: Oils and butter of seed from Brazilian biodiversity are extending the range of innovative products for cosmetics development. They have a fat potential similar to skin composition, leading to the improved performance of these product. Aims: Improve the emulsions spreadability through prior screening of grease composition and studying the viscosity, and the emulsions accelerated stability. Methods: Emulsions were formulated using oils from semiarid plants from Bahia: Syagrus coronate, Pachira retusa, and Pachira aquatica, so as to compare them with oils already standard in the production of cosmetics. Spreadability and stability tests were made comparing the results. The same criteria were used with Amazon seed butter: Virola surinamensis, Butyrospermum parkii, Astrocaryum murumuru, Theobroma cacao and Theobroma grandiflorum. For the emulsions screening and performance, a system was developed for oil/ butter, following tests of accelerated stability, viscosity, and spreadability. Results: The combined system of spreadability was optimized using screening. Emollients containing oleic and palmitic acids, and light chain fatty acids obtained good spreadability. The oil emulsion containing Pachira retusa and Virola surinamensis butter had a higher viscosity. Conclusions: With high content of fatty acids such as oleic, palmitic or the light chain fatty acids obtain an appropriated appearance, texture, and spreadability for cosmetic use. Thus, oils with a low fatty acid content may be combined with butter that have a high fatty acid content and vice-versa. Analyzing and strategically combining grease composition, one can optimize the performance of cosmetic formulations.

Study of a magnetorheological grease clutch

International Nuclear Information System (INIS)

Kavlicoglu, Barkan M; Gordaninejad, Faramarz; Wang, Xiaojie

2013-01-01

In high-speed viscous clutch applications that require low drag (viscous) torque, magnetorheological (MR) fluids are problematic due to their plastic viscosity. As the clutch speed increases the drag torque might exceed the allowable drag torque limit, because the viscous torque is proportional to the speed. To eliminate this problem, various MR greases are utilized in a clutch and their performance is examined. In the experimental study, the torque transfer capacity of a double-plate clutch for operating speeds up to 1200 rpm is conducted. Six different MR greases with various particle loadings and particle sizes are evaluated in the clutch. The rheological properties of MR grease with 90% particle loading in weight are compared with a commercially available MR fluid. The torque performance of the MR grease clutch is also compared with that of the clutch using MR fluid. It is demonstrated that the off-state (no applied magnetic field) torque output of the MR grease clutch is constant in the tested range of the operating speed. In contrast, the torque capacity of the clutch with MR fluid shows a strong dependence on the operating speed. Moreover, it is shown that the iron particle size of the MR grease does not affect the torque output. The MR greases demonstrated an up to 75% increase in the torque capacity compared to the commercial MR fluid. (paper)

Mechanisms of fat, oil and grease (FOG) deposit formation in sewer lines.

Science.gov (United States)

He, Xia; de los Reyes, Francis L; Leming, Michael L; Dean, Lisa O; Lappi, Simon E; Ducoste, Joel J

2013-09-01

FOG deposits in sewer systems have recently been shown to be metallic salts of fatty acids. However, the fate and transport of FOG deposit reactant constituents and the complex interactions during the FOG deposit formation process are still largely unknown. In this study, batch tests were performed to elucidate the mechanisms of FOG deposit formation that lead to sanitary sewer overflows (SSOs). We report the first formation of FOG deposits on a concrete surface under laboratory conditions that mimic the formation of deposits in sewer systems. Results showed that calcium, the dominant metal in FOG deposits, can be released from concrete surfaces under low pH conditions and contribute to the formation process. Small amounts of additional oil to grease interceptor effluent substantially facilitated the air/water or pipe surface/water interfacial reaction between free fatty acids and calcium to produce surface FOG deposits. Tests of different fatty acids revealed that more viscous FOG deposit solids were formed on concrete surfaces, and concrete corrosion was accelerated, in the presence of unsaturated FFAs versus saturated FFAs. Based on all the data, a comprehensive model was proposed for the mechanisms of FOG deposit formation in sewer systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

Studies on Hydrotreating Process of Microcrystalline Wax Produced from Marine Belayim Crude Oil

International Nuclear Information System (INIS)

EI Karashi, S.; Marawan, H.

2004-01-01

Abstract Microcrystalline wax was produced from solvent dewaxing process of vacuum residue raffinate produced from Marine Belayim origin. The untreated microcrystalline wax contains trace amounts of sulfur, oxygen, nitrogen and organometallic compounds as well as heavy aromatics which affect the properties of wax applications in pharmaceutical and technical fields . Microcrystalline wax hydrotreating process was studied using digital controlled unit and Ni O-MoO 3 / Al 2 O 3 catalyst, where operating parameters that controlled the efficiency of the hydrotreated wax were studied separately at different values including reactor temperature, reactor pressure, liquid hourly space velocity and hydrogen to hydrocarbon ratio . Hydrotreated microcrystalline wax at operating conditions (temperature 300 degree C, pressure 73 kg/cm 2 , LHS V 0.52 h-l and H 2 /HC ratio 266.6 Nm 3 /m 3 ) has the best quality to be used as food grade wax

Degradation Characterization of Thermal Interface Greases

Energy Technology Data Exchange (ETDEWEB)

Major, Joshua [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Narumanchi, Sreekant V [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Paret, Paul P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Blackman, Gregory [DuPont; Wong, Arnold [DuPont; Meth, Jeffery [DuPont

2018-02-12

Thermal interface materials (TIMs) are used in power electronics packaging to minimize thermal resistance between the heat generating component and the heat sink. Thermal greases are one such class. The conformability and thin bond line thickness (BLT) of these TIMs can potentially provide low thermal resistance throughout the operation lifetime of a component. However, their performance degrades over time due to pump-out and dry-out during thermal and power cycling. The reliability performance of greases through operational cycling needs to be quantified to develop new materials with superior properties. NREL, in collaboration with DuPont, has performed thermal and reliability characterization of several commercially available thermal greases. Initial bulk and contact thermal resistance of grease samples were measured, and then the thermal degradation that occurred due to pump-out and dry-out during temperature cycling was monitored. The thermal resistances of five different grease materials were evaluated using NREL's steady-state thermal resistance tester based on the ASTM test method D5470. Greases were then applied, utilizing a 2.5 cm x 2.5 cm stencil, between invar and aluminum plates to compare the thermomechanical performance of the materials in a representative test fixture. Scanning Acoustic microscopy, thermal, and compositional analyses were performed periodically during thermal cycling from -40 degrees C to 125 degrees C. Completion of this characterization has allowed for a comprehensive evaluation of thermal greases both for their initial bulk and contact thermal performance, as well as their degradation mechanisms under accelerated thermal cycling conditions.

Modeling of asphaltene and wax precipitation

Energy Technology Data Exchange (ETDEWEB)

Chung, F.; Sarathi, P.; Jones, R.

1991-01-01

This research project was designed to focus on the development of a predictive technique for organic deposition during gas injection for petroleum EOR. A thermodynamic model has been developed to describe the effects of temperature, pressure, and composition on asphaltene precipitation. The proposed model combines regular solution theory with Flory-Huggins polymer solutions theory to predict maximum volume fractions of asphaltene dissolved in oil. The model requires evaluation of vapor-liquid equilibria, first using an equation of state followed by calculations of asphaltene solubility in the liquid-phase. A state-of-the-art technique for C{sub 7+} fraction characterization was employed in developing this model. The preliminary model developed in this work was able to predict qualitatively the trends of the effects of temperature, pressure, and composition. Since the mechanism of paraffinic wax deposition is different from that of asphaltene deposition, another thermodynamic model based on the solid-liquid solution theory was developed to predict the wax formation. This model is simple and can predict the wax appearance temperature with reasonable accuracy. Accompanying the modeling work, experimental studies were conducted to investigate the solubility of asphaltene in oil land solvents and to examine the effects of oil composition, CO{sub 2}, and solvent on asphaltene precipitation and its properties. This research focused on the solubility reversibility of asphaltene in oil and the precipitation caused by CO{sub 2} injection at simulated reservoir temperature and pressure conditions. These experiments have provided many observations about the properties of asphaltenes for further improvement of the model, but more detailed information about the properties of asphaltenes in solution is needed for the development of more reliable asphaltene characterization techniques. 50 refs., 8 figs., 7 tabs.

Effect of emulsifier type and concentration, aqueous phase volume and wax ratio on physical, material and mechanical properties of water in oil lipsticks.

Science.gov (United States)

Beri, A; Norton, J E; Norton, I T

2013-12-01

Water-in-oil emulsions in lipsticks could have the potential to improve moisturizing properties and deliver hydrophilic molecules to the lips. The aims of this work were (i) to investigate the effect of emulsifier type (polymer vs. monomer, and saturated vs. unsaturated chain) and concentration on droplet size and (ii) to investigate the effect of wax ratio (carnauba wax, microcrystalline wax, paraffin wax and performalene) and aqueous phase volume on material properties (Young's modulus, point of fracture, elastic modulus and viscous modulus). Emulsion formation was achieved using a high shear mixer. Results showed that the saturated nature of the emulsifier had very little effect on droplet size, neither did the use of an emulsifier with a larger head group (droplet size ~18-25 μm). Polyglycerol polyricinoleate (PGPR) resulted in emulsions with the smallest droplets (~3-5 μm), as expected from previous studies that show that it produces a thick elastic interface. The results also showed that both Young's modulus and point of fracture increase with increasing percentage of carnauba wax (following a power law dependency of 3), but decrease with increasing percentage of microcrystalline wax, suggesting that the carnauba wax is included in the overall wax network formed by the saturated components, whereas the microcrystalline wax forms irregular crystals that disrupt the overall wax crystal network. Young's modulus, elastic modulus and viscous modulus all decrease with increasing aqueous phase volume in the emulsions, although the slope of the decrease in elastic and viscous moduli is dependent on the addition of solid wax, as a result of strengthening the network. This work suggests the potential use for emulsions in lipstick applications, particularly when PGPR is used as an emulsifier, and with the addition of solid wax, as it increases network strength. © 2013 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

7 CFR 2902.31 - Greases.

Science.gov (United States)

2010-01-01

... applies are: (i) Food grade greases. Lubricants that are designed for use on food-processing equipment as... parts and equipment in locations in which there is exposure of the lubricated part to food. (ii... are designed for use on railroad tracks or heavy crane tracks. (iv) Truck greases. Lubricants that are...

Dirt-binding particles consisting of hydrogenated castor oil beads constitute a nonirritating alternative for abrasive cleaning of recalcitrant oily skin contamination in a three-step programme of occupational skin protection.

Science.gov (United States)

Mahler, V; Erfurt-Berge, C; Schiemann, S; Michael, S; Egloffstein, A; Kuss, O

2010-04-01

In occupational fields with exposure to grease, oil, metal particles, coal, black lead or soot, cleansing formulations containing abrasive bodies (e.g. refined walnut shell, corn, wood, plastic or pumice) are used. These may constitute an irritant per se. As an alternative, hydrogenated castor oil (also known as castor wax) beads have been developed as dirt-binding particles. A polar surface contributes to their mechanical cleaning effects in removal of oily grime. Standardized examination of the in vivo effects upon the skin barrier of castor wax beads in comparison with abrasive bodies and pure detergent. Three cleansing preparations - (i) detergent, (ii) detergent containing castor wax beads, (iii) detergent containing walnut shell powder - were each repetitively applied in vivo (four times daily for 3 weeks), mimicking workplace conditions, in 30 healthy volunteers (15 with and 15 without an atopic skin diathesis) and compared vs. (iv) no treatment. The treatment effects upon the skin barrier were monitored by repeated measurements of functional parameters [transepidermal water loss (TEWL), redness] and surface topography. After a 3-week treatment, a significant global treatment effect (P dirt and use of skin protection and skin care measures under real workplace conditions, this component may now be used and examined further in different occupations.

In vitro erythemal UV-A protection factors of inorganic sunscreens distributed in aqueous media using carnauba wax-decyl oleate nanoparticles.

Science.gov (United States)

Villalobos-Hernández, J R; Müller-Goymann, C C

2007-01-01

This paper describes the in vitro photoprotection in the UV-A range, i.e. 320-400 nm obtained by the use of carnauba wax-decyl oleate nanoparticles either as encapsulation systems or as accompanying vehicles for inorganic sunscreens such as barium sulfate, strontium carbonate and titanium dioxide. Lipid-free inorganic sunscreen nanosuspensions, inorganic sunscreen-free wax-oil nanoparticle suspensions and wax-oil nanoparticle suspensions containing inorganic sunscreens dispersed either in their oil phase or their aqueous phase were prepared by high pressure homogenization. The in vitro erythemal UV-A protection factors (EUV-A PFs) of the nanosuspensions were calculated by means of a sun protection analyzer. EUV-A PFs being no higher than 4 were obtained by the encapsulation of barium sulfate and strontium carbonate, meanwhile by the distribution of titanium dioxide in presence of wax-oil nanoparticles, the EUV-A PFs varied between 2 and 19. The increase in the EUV-A PFs of the titanium dioxide obtained by the use of wax-oil nanoparticles demonstrated a better performance of the sun protection properties of this pigment in the UV-A region.

Screening of thermotolerant microorganisms and application for oil separation from palm oil mill wastewater

Directory of Open Access Journals (Sweden)

Aran H-Kittikun

2007-05-01

Full Text Available The characteristics of palm oil mill wastewater (POMW were brown color, pH 3.8-4.3, temperature 48-55oC, total solids 68.2-82.1 g/l, suspended solids 26.2-65.6 g/l, oil and grease 19.1-25.1 g/l, COD 49.9-160.7g/l and BOD 32.5-75.3 g/l. After centrifugation (3,184 xg of 50 ml POMW for 10 min, the POMW was separated into 3 layers: top (oil, middle (supernatant and bottom layer (sediment. The sediment containeddry weight 1.19 g and oil and grease 1.07 g. In order to release oil and grease trapped in palm fiber debris in the POMW, cellulase- and/or xylanase-enzyme-producing and thermotolerant microorganisms wereisolated. The isolates SO1 and SO2 were isolated from soil near the first anaerobic pond of the palm oil mill. They were aerobic, Gram positive, rod shaped, thermotolerant microorganisms and produced cellulase 12.11 U/ml (3 days and 7.2 U/ml (4 days, and xylanase 50.98 U/ml (4 days and 20.42 U/ml (4 days, respectivelyin synthetic medium containing carboxymethycellulose as a carbon source. When these 2 isolates were added into the steriled POMW under shaking condition for 7 days, after centrifugation at 3,184 xg the isolate SO1gave the better % reduction of dry weight (64.66 % and of oil and grease in the bottom layer (85.32 % of the POMW.

Biopretreatment of palm oil mill effluent by thermotolerant polymer-producing fungi

Directory of Open Access Journals (Sweden)

Masao Ukita

2001-11-01

Full Text Available Palm oil industry is one of the three major agro-industries in Southern Thailand and generates large quantities of effluent with high organic matter (BOD and COD values of 58,000 and 110,000 mg/l, respectively, total solids and suspended solids (70,000 and 40,000 mg/l, respectively, oil & grease (25,600 mg/l, and has a low pH (4.5. Conventional anaerobic ponding system is normally employed in palm oil mills to treat the effluent. To increase its efficiency, biopretreatment to remove the organic matter and oil & grease by thermotolerant polymer-producing fungi was investigated. The palm oil mill effluent (POME was treated by the two thermotolerant polymer-producing fungi, Rhizopus sp. ST4 and Rhizopus sp. ST29, at 45ºC under aseptic and septic conditions. Rhizopus sp. ST4 gave the same oil & grease removal (84.2% under both conditions but COD removal under septic condition (62.2% was 8.8% higher than that under aseptic condition (53.4%. On the contrary, Rhizopus sp. ST 29 under aseptic condition showed 11% and 25.4% higher oil & grease removal (91.4% and COD removal (66.0% than those under septic condition. Comparison between the two isolates under aseptic condition revealed that Rhizopus sp. ST29 exhibited higher oil & grease removal (91.4% as well as COD removal (66.0% than those of Rhizopus sp. ST4 (84.2% and 53.4%, respectively. Under septic condition, Rhizopus sp. ST4 gave higher oil & grease removal (84.2% and COD removal (62.2% than did Rhizopus sp. ST 29 (80.5 and 40.6%, respectively.

Statistical modelling of Fat, Oil and Grease (FOG) deposits in wastewater pump sumps.

Science.gov (United States)

Nieuwenhuis, Eva; Post, Johan; Duinmeijer, Alex; Langeveld, Jeroen; Clemens, François

2018-05-15

The accumulation of FOG (Fat, Oil and Grease) deposits in sewer pumping stations results in an increase in maintenance costs, malfunctioning of pumps and, a potential increase of wastewater spills in receiving open water bodies. It is thought that a variety of parameters (e.g. geometry of the pump sump, pump operation, socioeconomic parameters of the catchment) influences the built-up of FOG. Based on a database containing data of 126 pumping stations located in five Dutch municipalities a statistical model was built. It is shown that 3 parameters are most significant in explaining the occurrence of FOG deposits: mean income of the population in a catchment, the amount of energy (kinetic and potential) per m 3 per day and the density of restaurants, bars and hotels in a catchment. Further it is shown that there are significant differences between municipalities that can be traced back to the local 'design paradigm'. For example, in Amsterdam, the design philosophy of discharging in the pump sump under the water surface (and hence maintaining a low level of turbulence in the pump sump) results in an increase of the probability of the formation of FOG. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Understanding the spatial formation and accumulation of fats, oils and grease deposits in the sewer collection system.

Science.gov (United States)

Dominic, Christopher Cyril Sandeep; Szakasits, Megan; Dean, Lisa O; Ducoste, Joel J

2013-01-01

Sanitary sewer overflows are caused by the accumulation of insoluble calcium salts of fatty acids, which are formed by the reaction between fats, oils and grease (FOG) and calcium found in wastewaters. Different sewer structural configurations (i.e., manholes, pipes, wet wells), which vary spatially, along with other obstructions (roots intrusion) and pipe deformations (pipe sags), may influence the detrimental buildup of FOG deposits. The purpose of this study was to quantify the spatial variation in FOG deposit formation and accumulation in a pilot-scale sewer collection system. The pilot system contained straight pipes, manholes, roots intrusion, and a pipe sag. Calcium and oil were injected into the system and operated at alkaline (pH = 10) and neutral (pH = 7) pH conditions. Results showed that solid accumulations were slightly higher at neutral pH. Fourier transform infrared (FTIR) analysis on the solids samples confirmed that the solids were indeed calcium-based fatty acid salts. However, the fatty acid profiles of the solids deviated from the profile found from FOG deposits in sewer systems, which were primarily saturated fatty acids. These results confirm the work done previously by researchers and suggest an alternative fate of unsaturated fatty acids that does not lead to their incorporation in FOG deposits in full-scale sewer systems.

The reduction of oil pollutants of petroleum products storage-tanks sludge using low-cost adsorbents

Directory of Open Access Journals (Sweden)

Mokhtari-Hosseini Zahra Beagom

2017-01-01

Full Text Available Disposal of storage tank sludge in oil depots is a major environmental concern due to the high concentration of hydrocarbons involved. This paper investigates the reduction of the sludge oil pollutants with initial oil and grease concentration of about 50 mass% using low cost adsorbents. Among the examined adsorbents, sawdust indicated the maximum removal of oil and grease. The screening and optimizing of process parameters were evaluated employing Plackett-Burman design and response surface method. For the optimized conditions, more than 60 mass% of oil and grease from the sludge was removed. Moreover, it was found that sawdust adsorption of the oil and grease approximately followed the Freundlich isotherm. The results indicated that oil pollutants of sludge could be reduced using sawdust as a low-cost, available and flammable adsorbent so that thus saturated adsorbents could be used as fuel in certain industries.

Review of the Factors that Influence the Condition of Wax Deposition in Subsea Pipelines

Directory of Open Access Journals (Sweden)

Koh Junyi

2018-03-01

Full Text Available When crude oil is transported via sub-sea pipeline, the temperature of the pipeline decreases at a deep depth which causes a difference in temperature with the crude oil inside. This causes the crude oil to dissipate its heat to the surrounding until thermal equilibrium is achieved. This is also known as the cloud point where wax begins to precipitate and solidifies at the walls of the pipeline which obstruct the flow of fluid. The main objective of this review is to quantify the factors that influence wax deposition such as temperature difference between the wall of the pipeline and the fluid flowing within, the flow rate of the fluid in the pipeline and residence time of the fluid in the pipeline. It is found the main factor that causes wax deposition in the pipeline is the difference in temperature between the petroleum pipeline and the fluid flowing within. Most Literature deduces that decreasing temperature difference results in lower wax content deposited on the wall of the pipeline. The wax content increases with rising flow rate. As for the residence time, the amount of deposited wax initially increases when residence time increases until it reaches a peak value and gradually decreases. Flow-loop system and cold finger apparatus were used in literature investigations to determine the trends above. Three new models are generated through a regression analysis based on the results from other authors. These new models form a relationship between temperature difference, flow rate, residence time and Reynolds number with wax deposition. These models have high values of R-square and adjusted R-square which demonstrate the reliability of these models.

Degradation Characterization of Thermal Interface Greases: Preprint

Energy Technology Data Exchange (ETDEWEB)

DeVoto, Douglas J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Major, Joshua [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Paret, Paul P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Blackman, G. S. [DuPont Experimental Station; Wong, A. [DuPont Experimental Station; Meth, J. S. [DuPont Experimental Station

2017-08-03

Thermal interface materials (TIMs) are used in power electronics packaging to minimize thermal resistance between the heat generating component and the heat sink. Thermal greases are one such class. The conformability and thin bond line thickness (BLT) of these TIMs can potentially provide low thermal resistance throughout the operation lifetime of a component. However, their performance degrades over time due to pump-out and dry-out during thermal and power cycling. The reliability performance of greases through operational cycling needs to be quantified to develop new materials with superior properties. NREL, in collaboration with DuPont, has performed thermal and reliability characterization of several commercially available thermal greases. Initial bulk and contact thermal resistance of grease samples were measured, and then the thermal degradation that occurred due to pump-out and dry-out during temperature cycling was monitored. The thermal resistances of five different grease materials were evaluated using NREL's steady-state thermal resistance tester based on the ASTM test method D5470. Greases were then applied, utilizing a 2.5 cm x 2.5 cm stencil, between invar and aluminum plates to compare the thermomechanical performance of the materials in a representative test fixture. Scanning Acoustic microscopy, thermal, and compositional analyses were performed periodically during thermal cycling from -40 degrees Celcius to 125 degrees Celcius. Completion of this characterization has allowed for a comprehensive evaluation of thermal greases both for their initial bulk and contact thermal performance, as well as their degradation mechanisms under accelerated thermal cycling conditions.

High-purity fatty acid methyl ester production from canola, soybean, palm, and yellow grease lipids by means of a membrane reactor

International Nuclear Information System (INIS)

Cao Peigang; Dube, Marc A.; Tremblay, Andre Y.

2008-01-01

High-purity fatty acid methyl ester (FAME) was produced from different lipids, such as soybean oil, canola oil, a hydrogenated palm oil/palm oil blend, yellow grease, and brown grease, combined with methanol using a continuous membrane reactor. The membrane reactor combines reaction and separation in a single unit, provides continuous mixing of raw materials, and maintains a high molar ratio of methanol to lipid in the reaction loop while maintaining two phases during the reaction. It was demonstrated that the membrane reactor can be operated using a very broad range of feedstocks at highly similar operating conditions to produce FAME. The total glycerine and free glycerine contents of the FAME produced were below the ASTM D6751 standard after a single reaction step. Under essentially the same reaction conditions, a conventional batch reaction was not able to achieve the same degree of FAME purity. The effect of the fatty acid composition of the lipid feedstocks on the FAME purity was also shown. It was demonstrated that, due to the fatty acid composition, FAME from virgin soybean oil and virgin canola oil was produced in the membrane reactor within ASTM specifications even without a water washing step

Biodegradation of paraffin wax by crude Aspergillus enzyme preparations for potential use in removing paraffin deposits.

Science.gov (United States)

Zhang, Junhui; Xue, Quanhong; Gao, Hui; Wang, Ping

2015-11-01

Paraffin deposition problems have plagued the oil industry. Whist mechanical and chemical methods are problematic, microbiological method of paraffin removal is considered an alternative. However, studies have mainly investigated the use of bacteria, with little attention to the potential of fungi. The performance of six Aspergillus isolates to degrade paraffin wax was evaluated under laboratory conditions using solid enzyme preparations. The results showed that all the six enzyme preparations efficiently improved the solubility of paraffin wax in n-hexane and degraded n-alkanes in paraffin wax. The degradation process was accompanied by dynamic production of gases (CO2 and H2 ) and organic acids (oxalate and propionate). The shape of wax crystals markedly changed after enzymatic degradation, with a rough surface and a loose structure. This study indicates that extracellular enzymes from Aspergillus spp. can efficiently degrade paraffin wax. These enzyme preparations have the potential for use in oil wells with paraffin deposition problems. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ear wax

Science.gov (United States)

See your provider if your ears are blocked with wax and you are unable to remove the wax. Also call if you have an ear wax blockage and you develop new symptoms, such as: Drainage from the ear Ear pain Fever Hearing loss that continues after you clean the wax

Jojoba oil and derivates

Energy Technology Data Exchange (ETDEWEB)

Wisniak, T

1977-01-01

Jojoba oil differs from all known seed oils by its almost complete absence of glycerides, making it more a liquid wax than a fat. It has become important as a possible substitute for sperm-whale oil to produce lubricants, lubricant additives and other products. The plant occurs naturally in southern Arizona and N.W. Mexico and its oil has long been used by Indians for medicinal, culinary, ritual and other purposes. It tolerates extreme daily fluctuations of temperature and grows well under the difficult soil and moisture conditions of the region. In the first part of this review the plant and its uses are described, including its floral, fruit and seed anatomy and the use of liquid wax during germination. Stored coryledon wax is used up by the embryo as a linear function of time during the first 30 days of germination and growth. Before germination, seeds weight about 0.59 mg and contain about 54% wax. The second and greater part of the review deals with jojoba oil (its extraction, properties, molecular description, toxicity and composition), jojoba meal, which remains after the oil has been extracted, and the chemical modification of the oil.

[Determination of 3-monochloropropane-1,2-diol in grease food by solid phase extraction-derivatization-gas chromatography-mass spectrometry].

Science.gov (United States)

Xiang, Xiaoling; Wang, Liyuan; Shen, Xianghong; Li, Chunsong; Shen, Jianfu; Wu, Pinggu

2017-09-01

To establish the method of determination of 3-monochloropropane-1,2-diol( 3-MCPD) in grease food by gas chromatography-mass spectrometry( GC-MS). 3-MCPD in grease food represented by bean paste was extracted by ultrasound,purified by alkaline earth solid phase extraction column,derivatived using phenylboronic acid( PBA) and detected by GC-MS. The linearity of 3-MCPD ranged from 1-100 ng/mL,with correlation coefficient at 0. 9993.The limits of quantitation( LOQ) in soy sauce,bean paste,pepper oil were 0. 6,0. 5 and7. 0 μg/kg and limits of detection( LOD) were 1. 9,1. 6 and 18. 8 μg/kg,respectively.Average recovery rate and relative standard deviation was 78. 3%-106. 7% and 1. 9%-11. 6%( n = 6), when 3-MCPD was added in grease food at 2. 5-1000 μg/kg. The method has good purification effect and the detection sensitivity and accuracy,and can be used for the determination of 3-MCPD in grease food.

The Preparation and Performances of Self-Dispersed Nanomicron Emulsified Wax Solid Lubricant Ewax for Drilling Fluids

Directory of Open Access Journals (Sweden)

Feng-shan Zhou

2014-01-01

Full Text Available An oil-in-water nanomicron wax emulsion with oil phase content 45 wt% was prepared by using the emulsifying method of surfactant-in-oil. The optimum prepared condition is 85°C, 20 min, and 5 wt% complex emulsifiers. Then the abovementioned nanomicron emulsifying wax was immersed into a special water-soluble polymer in a certain percentage by the semidry technology. At last, a solidified self-dispersed nanomicron emulsified wax named as Ewax, a kind of solid lubricant for water based drilling fluid, was obtained after dried in the special soluble polymer containing emulsifying wax in low temperature. It is shown that the adhesion coefficient reduced rate (ΔKf is 73.5% and the extreme pressure (E-P friction coefficient reduced rate (Δf is 77.6% when the produced Ewax sample was added to fresh water based drilling fluid at dosage 1.0 wt%. In comparison with other normal similar liquid products, Ewax not only has better performances of lubrication, filtration loss control property, heat resistance, and tolerance to salt and is environmentally friendly, but also can solve the problems of freezing in the winter and poor storage stability of liquid wax emulsion in oilfield applications.

Consistency-dependent optical properties of lubricating grease studied by terahertz spectroscopy

International Nuclear Information System (INIS)

Tian Lu; Zhao Kun; Zhou Qing-Li; Shi Yu-Lei; Zhao Dong-Mei; Zhang Cun-Lin; Zhao Song-Qing; Zhao Hui; Bao Ri-Ma; Zhu Shou-Ming; Miao Qing

2011-01-01

The optical properties of four kinds of lubricating greases (urea, lithium, extreme pressure lithium, molybdenum disulfide lithium greases) with different NLGL (National Lubricant Grease Institute of America) numbers were investigated using terahertz time-domain spectroscopy. Greases with different NLGL grades have unique spectral features in the terahertz range. Comparison of the experimental data with predictions based on Lorentz—Lorenz theory exhibited that the refractive indices of each kind of lubricating grease were dependent on the their consistency. In addition, molybdenum disulfide (MoS 2 ) as a libricant additive shows strong absorption from 0.2 to 1.4 THz, leading to higher absorption of MoS 2 -lithium grease than that of lithium grease. (general)

Solid lubricants in the power station

International Nuclear Information System (INIS)

Gaensheimer, J.

1981-01-01

Example application are first outlined, followed by descriptions of inorganic solid lubricants and plastics. Waxes, soaps and salts are discussed. Notes for usage are given. Solid lubricants in oils and greases are comprehensively described, followed by the sections entitled Solid lubricants for gearboxes . References to samples, tests, standards and bibliography make up the conclusion. (orig.) [de

Analysis of the constituents in jojoba wax used as a food additive by LC/MS/MS.

Science.gov (United States)

Tada, Atsuko; Jin, Zhe-Long; Sugimoto, Naoki; Sato, Kyoko; Yamazaki, Takeshi; Tanamoto, Kenichi

2005-10-01

Jojoba wax is a natural gum base used as a food additive in Japan, and is obtained from jojoba oil with a characteristically high melting point. Although the constituents of jojoba oil have been reported, the quality of jojoba wax used as a food additive has not yet been clarified. In order to evaluate its quality as a food additive and to obtain basic information useful for setting official standards, we investigated the constituents and their concentrations in jojoba wax. LC/MS analysis of the jojoba wax showed six peaks with [M+H]+ ions in the range from m/z 533.6 to 673.7 at intervals of m/z 28. After isolation of the components of the four main peaks by preparative LC/MS, the fatty acid and long chain alcohol moieties of the wax esters were analyzed by methanolysis and hydrolysis, followed by GC/MS. The results indicated that the main constituents in jojoba wax were various kinds of wax esters, namely eicosenyl octadecenoate (C20:1-C18:1) (1), eicosenyl eicosenoate (C20:1-C20:1) (II), docosenyl eicosenoate (C22:1-C20:1) (III), eicosenyl docosenoate (C20:1-C22:1) (IV) and tetracosenyl eiosenoate (C24:1-C20:1) (V). To confirm and quantify the wax esters in jojoba wax directly, LC/MS/MS analysis was performed. The product ions corresponding to the fatty acid moieties of the wax esters were observed, and by using the product ions derived from the protonated molecular ions of wax esters the fatty acid moieties were identified by MRM analysis. The concentrations of the wax esters I, II and III, in jojoba wax were 5.5, 21.4 and 37.8%, respectively. In summary, we clarified the main constituents of jojoba wax and quantified the molecular species of the wax esters without hydrolysis by monitoring their product ions, using a LC/MS/MS system.

Decontamination of cosmetic and their raw materials by radiation

International Nuclear Information System (INIS)

Virzeu, D.M.

1990-01-01

The effects of gamma radiation over some cosmetic materials (solvent; thickening, talc, wax, vegetal oils, mineral, animal and synthetic oils, grease, emulsifying, conserving anti oxidizing and vitamin) are shown. The doses used were 20 KGy and 50 KGy, that are considered sterilizing and used in medical-surgical materials. The relation of the showed products is useful as a radio sensibility standard, but both can take as an indicator of what can be or not irradiated. (C.G.C.)

Wax encapsulation of water-soluble compounds for application in foods.

Science.gov (United States)

Mellema, M; Van Benthum, W A J; Boer, B; Von Harras, J; Visser, A

2006-11-01

Water-soluble ingredients have been successfully encapsulated in wax using two preparation techniques. The first technique ('solid preparation') leads to relatively large wax particles. The second technique ('liquid preparation') leads to relatively small wax particles immersed in vegetable oil. On the first technique: stable encapsulation of water-soluble colourants (dissolved at low concentration in water) has been achieved making use of beeswax and PGPR. The leakage from the capsules, for instance of size 2 mm, is about 30% after 16 weeks storage in water at room temperature. To form such capsules a minimum wax mass of 40% relative to the total mass is needed. High amounts of salt or acids at the inside water phase causes more leaking, probably because of the osmotic pressure difference. Osmotic matching of inner and outer phase can lead to a dramatic reduction in leakage. Fat capsules are less suitable to incorporate water soluble colourants. The reason for this could be a difference in crystal structure (fat is less ductile and more brittle). On the second technique: stable encapsulation of water-soluble colourants (encapsulated in solid wax particles) has been achieved making use of carnauba wax. The leakage from the capsules, for instance of size 250 mm, is about 40% after 1 weeks storage in water at room temperature.

Physical characteristics of tetrahydroxy and acylated derivatives of jojoba liquid wax

Science.gov (United States)

Jojoba liquid wax is a mixture of esters of long chain fatty acids and fatty alcohols, mainly (C38:2-C46:2). The oil exhibits excellent emolliency on the skin and therefore is a component in many personal care cosmetic formulations. The virgin oil is a component of the seed of the Jojoba (Simmondsia...

Evaluation of physical and chemical properties and their interactions in fat, oil, and grease (FOG) deposits.

Science.gov (United States)

Gross, Martin A; Jensen, Jeanette L; Gracz, Hanna S; Dancer, Jens; Keener, Kevin M

2017-10-15

Fat, oil and grease (FOG) blockages in sewer systems are a substantial problem in the United States. It has been estimated that over 50% of sewer overflows are a result of FOG blockages. In this work, a thorough laboratory study was undertaken to examine key variables that contribute to FOG deposit formation under controlled conditions. Physical and chemical properties and their interactions were evaluated and conditions that generated deposits that mimicked field FOG deposits were identified. It was found that 96 of the of 128 reaction conditions tested in the laboratory formed FOG deposits with similar physical and chemical characteristics as field FOG deposits. It was also found that FOG deposits can be created through fatty acid crystallization and not just saponification. Furthermore FOG deposits were found to be more complex than previously documented and contain free fatty acids, fatty acid metal salts, triacylglycerol's, diacylglycerol's and, monoacylglycerol's. Lastly it was found that FOG deposits that only contained saturated fatty acids were on average 2.1 times higher yield strength than deposits that contained unsaturated fatty acids. Copyright © 2017 Elsevier Ltd. All rights reserved.

Detection of Elemental Composition of Lubricating Grease Using Laser Induced Breakdown Spectroscopy

Directory of Open Access Journals (Sweden)

Cherry Dhiman

2014-12-01

Full Text Available The elemental composition of lubricating soft grease used in rail engines are studied using laser induced breakdown spectroscopy (LIBS technique. LIBS spectra of fresh, partially used and fully used grease samples are recorded using time-gated ICCD spectrometer for verification of compositional degradation of the used grease. LIBS spectra of grease samples are analyzed by comparing with emission spectra of elements published by NIST standard database. Many spectral lines of impurity elements like Fe, Cu, Ba, Mg, Mn, Ni, S, Zn, Si, Pb, Ti, Ca and Al present in the grease in ppm or ppb level in trace level concentrations are observed in excess in the used grease mainly due to wear and tear. On the other hand in fresh grease, spectral lines of Ca, Al and Na are observed predominantly.

Policosanol fabrication from insect wax and optimization by response surface methodology.

Science.gov (United States)

Ma, Jinju; Ma, Liyi; Zhang, Hong; Zhang, Zhongquan; Wang, Youqiong; Li, Kai; Chen, Xiaoming

2018-01-01

Insect wax is a famous biological resource for the role in economic production in China. Insect wax is a good source of policosanol, which may is a candidate supplement in foodstuff and pharmaceuticals that has important physiological activities. Therefore, this work aims to investigate a high-yield and rapid method for policosanol fabrication from insect wax. The conditions for policosanol fabrication were optimized as follows: an oil bath temperature of 112.7°C and reductant dosage of 0.97 g (used for the reduction of 10.00 g of insect wax). The yield of policosanol reached 83.20%, which was 4 times greater than that of existing methods, such as saponification. The total content of policosanol obtained under the optimal conditions reached 87%. In other words, a high yield of policosanol was obtained from insect wax (723.84 mg/g), that was 55 times higher than that generated from beeswax-brown via saponification. The concentrations of metal residues in policosanol were within the limits of the European Union regulations and EFSA stipulation. The LD50 values for oral doses of insect wax and policosanol were both > 5 g/kg. Policosanol was fabricated via solvent-free reduction from insect wax using LiAlH4 at a high yield. The fabrication conditions were optimized. Policosanol and insect wax showed high security, which made them potential candidates as supplements in foods, pharmaceuticals and cosmetics. The rapid and high-yield method has great potential for commercial manufacturing of policosanol.

Assessment of the impact of oil spill on Mumbai harbor bay

International Nuclear Information System (INIS)

Pandit, G.G.; Saradhi, I.V.; Puranik, V.D.; Sharma, D.N.; Ghosh, A.K.

2011-04-01

On 7 th August, 2010 two cargo ships MSC Chitra and MV Khalijia collided off Mumbai coast causing an oil spill that spread quickly through Maharashtra's coastline. MSC Chitra ruptured its tank when it hit incoming MV Khalijia. MSC Chitra tilted to about 80 degrees soon after the collision, spilling an estimated 400 to 500 tonnes of oil. The ship was loaded with an estimated 2,600 tonnes of oil, 300 tonnes of diesel and 70 tonnes of lubricating oil at the time of the accident. The oil spill has spreaded over an area of 25 square kilometers. MSC Chitra was carrying 1219 containers out of which 31 had hazardous chemicals like organophosphate pesticides. After the collision about 400 containers fall off into to the sea from the deck of MSC Chitra. The oil spill has resulted in severe environmental damage along the Mumbai coastline as well as to the marine life. In order to assess the impact of oil spill on the marine environment daily monitoring of oil and grease levels has been carried out at CIRUS Jetty. Additionally three field surveys have been carried out along the coast line of Mumbai harbor bay from Vashi Jetty to Uran collecting sea water samples. The samples collected at CIRUS Jetty and Mumbai harbor bay are analyzed for various water quality parameters apart from oil and grease. The results indicate the oil and grease levels in sea water at CIRUS Jetty reduced to background levels within 15 days. The filed survey along Mumbai harbor bay also shows a decreasing trend in the oil and grease levels in seawater. (author)

Long-term evaluation of the needle surface wax condition of Pinus sylvestris around different industries in Lithuania

International Nuclear Information System (INIS)

Kupcinskiene, Eugenija; Huttunen, Satu

2005-01-01

The aim of our study was to evaluate the annual dynamics of needle surface wax erosion and wettability in Scots pines exposed to a gradient of industrial pollutants emitted from the main factories of Lithuania: a nitrogen fertilizer factory, an oil refinery and a cement factory. Decreased emissions (in the case of the oil refinery and the cement factory) were reflected in the increased structural surface area (SSA, i.e. area covered by tubular waxes) on the needles. The nearly constant amount of emissions from the nitrogen fertilizer factory within the 1994-2000 period corresponded to negligible annual differences in SSA. Annual changes in the hydrophobicity of needles on the investigated transects were small. Despite the decreased pollution within the 7-year period, industrial emissions are still causing significantly accelerated wax erosion and increased wettability in needles sampled from the stands most heavily affected by pollutants. - Tubular wax on the pine needle surface reflects changes/differences in industrial emissions

Cannabis-induced psychosis associated with high potency "wax dabs".

Science.gov (United States)

Pierre, Joseph M; Gandal, Michael; Son, Maya

2016-04-01

With mounting evidence that the risk of cannabis-induced psychosis may be related to both dose and potency of tetrahydrocannbinol (THC), increasing reports of psychosis associated with cannabinoids containing greater amounts of THC are anticipated. We report two cases of emergent psychosis after using a concentrated THC extract known as cannabis "wax," "oil," or "dabs" raising serious concerns about its psychotic liability. Although "dabbing" with cannabis wax is becoming increasingly popular in the US for both recreational and "medicinal" intentions, our cases raise serious concerns about its psychotic liability and highlight the importance of understanding this risk by physicians recommending cannabinoids for purported medicinal purposes. Published by Elsevier B.V.

Study of the nature of clarified oils and their potential uses

Energy Technology Data Exchange (ETDEWEB)

Nagpal, J.M.; Singh, I.D.; Tiwari, G.B.; Goyal, B.S.; Chandola, H.C. [Indian Institute of Petroleum, Dehradun (India)

1996-12-31

Vacuum Gas Oils (VGOs) from waxy crudes contain appreciable amounts of wax. During catalytic cracking of VGO, due to lop sided cracking of n-paraffins, a substantial amount of wax is retained in clarified oils. These clarified oils generally find their way into refinery fuel. Wax separated from clarified oils were characterised using nuclear magnetic resonance (n.m.r.) and infrared (i.r.) spectroscopy. The groupwise composition of the clarified oils were also studied and the data compared with a typical short residue. Waxes separated from the clarified oils contain an appreciably high proportion of n-paraffins indicating a potential feedstock for making {alpha}-olefins. Group type composition showed that the polar aromatics separated from the clarified oils have high BMCI values indicating the possibility of using them as feedstocks for carbon rich materials. 8 refs., 3 tabs.

The effect of waxes, as a complement to hydrothermal immersion, on the quality of papaya fruit (Carica papaya L. Pococí hybrid

Directory of Open Access Journals (Sweden)

V. Gustavo Corra

2015-06-01

Full Text Available Different waxes were evaluated as a complement to hydrothermal treatment on the overall papaya fruit quality parameters. The fruits were harvested, washed in water, disinfected with sodium hypochlorite and exposed to hydrothermal immersion treatment at 49°C/20 min (HT; then treatments were applied: 1 bees wax +palm oil 5% solution; 2 fatty acids wax mixture 4.7%; 3 chitosan 0.1%; 4 only HT; 5 control (no hydrothermal immersion nor wax. The fruit was stored for 15 days at 12°C, then at 20°C. Significant differences (p≤0.05 were found between fruits receiving HT complemented with 5% bees + palm oil wax, which exhibited lower respiration rate (12.27 ml CO2/kg*h a 8 days after leaving cold storage, as compared with those receiving only HT (16.72 ml CO2/ kg*h or control fruits (17.01 ml CO2/kg*h. The lesser percent of acumulated weight loss was registered whit TH plus bees wax cund palm oil. The color parameters were not affected, except for treatment 2, fatty acids wax mixture, which induced a delay in color development (p≤0.05. No changes were observed in internal or external firmness, nor in degrees brix. HT reduced the incidence of peduncular rot and anthracnose severity (p≤0.05, and extended useful life time. The use of waxes as a complement to HT can contribute to preserving some of the parameters which influence the final papaya fruit quality.

Effect of carbonyl iron particles composition on the physical characteristics of MR grease

Energy Technology Data Exchange (ETDEWEB)

Mohamad, Norzilawati, E-mail: mnorzilawati@gmail.com; Mazlan, Saiful Amri, E-mail: amri.kl@utm.my [Vehicle System Engineering, Malaysia – Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra (Jalan Semarak), Kuala Lumpur, 54000 (Malaysia); Ubaidillah, E-mail: ubaidillah@uns.ac.id [Vehicle System Engineering, Malaysia – Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra (Jalan Semarak), Kuala Lumpur, 54000 (Malaysia); Mechanical Engineering Department, Faculty of Engineering, Universitas Sebelas Maret, Jl. Ir. Sutami 36A, Kentingan, Surakarta, 57126, Central Java, Surakarta (Indonesia)

2016-03-29

Magnetorheological (MR) grease is an extension of the study of magnetorheological materials. The MR grease can help to reduce the particles sedimentation problem occurred in the MR fluids. Within this study, an effort has been taken to investigate the effect of different weight compositions of carbonyl iron particles on the physical and chemical characteristics of the MR grease under off-state condition (no magnetic field). The MR grease is prepared by mixing carbonyl iron particles having a size range of 1 to 10 µm with commercial NPC Highrex HD-3 grease. Characterizations of MR grease are investigated using Vibrating Sample Magnetometer (VSM), Environmental Scanning Electron Microscopy (ESEM), Differential Scanning Calorimeter (DSC) and rheometer. The dependency of carbonyl iron particles weight towards the magnetic properties of MR grease and other characterizations are investigated.

Development of formulations and processes to incorporate wax oleogels in ice cream.

Science.gov (United States)

Zulim Botega, Daniele C; Marangoni, Alejandro G; Smith, Alexandra K; Goff, H Douglas

2013-12-01

The objective of this study was to investigate the influence of emulsifiers, waxes, fat concentration, and processing conditions on the application of wax oleogel to replace solid fat content and create optimal fat structure in ice cream. Ice creams with 10% or 15% fat were formulated with rice bran wax (RBW), candelilla wax (CDW), or carnauba wax (CBW) oleogels, containing 10% wax and 90% high-oleic sunflower oil. The ice creams were produced using batch or continuous freezing processes. Transmission electron microscopy (TEM) and cryo-scanning electron microscopy were used to evaluate the microstructure of ice cream and the ultrastructure of oleogel droplets in ice cream mixes. Among the wax oleogels, RBW oleogel had the ability to form and sustain structure in 15% fat ice creams when glycerol monooleate (GMO) was used as the emulsifier. TEM images revealed that the high degree of fat structuring observed in GMO samples was associated with the RBW crystal morphology within the fat droplet, which was characterized by the growth of crystals at the outer edge of the droplet. Continuous freezing improved fat structuring compared to batch freezing. RBW oleogels established better structure compared to CDW or CBW oleogels. These results demonstrate that RBW oleogel has the potential to develop fat structure in ice cream in the presence of GMO and sufficiently high concentrations of oleogel. © 2013 Institute of Food Technologists®

Brown Grease to Biodiesel Demonstration Project Report

Energy Technology Data Exchange (ETDEWEB)

San Francisco Public Utilities Commission; URS Corporation; Biofuels, Blackgold; Carollo Engineers

2013-01-30

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas. The research goals are given below: To validate technology performance; To determine the costs and benefits [including economic, socioeconomic, and GHG emissions reduction] associated with co-locating this type of operation at a municipal wastewater treatment plant (WWTP); To develop a business case or model for replication of the

A news magnetic tools designed by ECOPETROL to inhibit wax in the petroleum production systems

Energy Technology Data Exchange (ETDEWEB)

Pelaez U, C.; Medina Z, C. [ECOPETROL, Instituto Colombiano del Petroleo (Colombia); Pena C, A. [INSERPET, Bucaramanga (Colombia)

1996-12-31

The deposition of wax and asphaltenes in production systems cause plugging in the flow lines reducing the oil production and increasing significantly the produced barrels prices. A wax magnetic inhibition technique has been tested with great success. The method has been improved with the use of magnetic tools. This work describes the experience and the results obtained with these tools. 6 figs., 1 tab.

A news magnetic tools designed by ECOPETROL to inhibit wax in the petroleum production systems

Energy Technology Data Exchange (ETDEWEB)

Pelaez U, C; Medina Z, C [ECOPETROL, Instituto Colombiano del Petroleo (Colombia); Pena C, A [INSERPET, Bucaramanga (Colombia)

1997-12-31

The deposition of wax and asphaltenes in production systems cause plugging in the flow lines reducing the oil production and increasing significantly the produced barrels prices. A wax magnetic inhibition technique has been tested with great success. The method has been improved with the use of magnetic tools. This work describes the experience and the results obtained with these tools. 6 figs., 1 tab.

Research on a lubricating grease print process for cylindrical cylinder

Science.gov (United States)

Yang, Liu; Zhang, Xuan; Wang, XianYan; Tan, XiaoYan

2017-09-01

In vehicle braking system and clutch system of transmission, there is always a kind of cylindrical component dose reciprocating motion. The main working method is the reciprocating motion between the rubber sealing parts and cylindrical parts, the main factor affects the service life of the product is the lubricating performance of the moving parts. So the lubricating performance between cylinders and rubber sealing rings is particularly important, same as the quality of the grease applies on the surface of the surface of cylinder. Traditional method of manually applying grease has some defects such as applying unevenly, applying tools like brush and cloth easily falls off and affect the cleanness of products, contact skin easily cause allergy, waste grease due to the uncontrollable of grease quantity using in applying, low efficiency of manual operation. An automatic, quantitative and high pressure applying equipment is introduced in this document to replace the traditional manually applying method, which can guarantee the applying quality of the grease which are painted on the surface of cylinder and bring economic benefits to the company.

Lubricating grease shear flow and boundary layers in a concentric cylinder configuration

NARCIS (Netherlands)

Li, J.X.; Westerberg, L.G.; Höglund, E.; Lugt, Pieter Martin; Baart, P.

2014-01-01

Grease is extensively used to lubricate various machine elements such as rolling bearings, seals, and gears. Understanding the flow dynamics of grease is relevant for the prediction of grease distribution for optimum lubrication and for the migration of wear and contaminant particles. In this study,

Impact of Water on the Rheology of Lubricating Greases

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2016-01-01

The operational life of bearings is often determined by the performance of the lubricating grease. The consistency of the grease prevents it from leaking out of the bearing and provides good sealing properties. The possible ingress of water into the bearing will have a considerable impact not only

A prediction method for the wax deposition rate based on a radial basis function neural network

Directory of Open Access Journals (Sweden)

Ying Xie

2017-06-01

Full Text Available The radial basis function neural network is a popular supervised learning tool based on machinery learning technology. Its high precision having been proven, the radial basis function neural network has been applied in many areas. The accumulation of deposited materials in the pipeline may lead to the need for increased pumping power, a decreased flow rate or even to the total blockage of the line, with losses of production and capital investment, so research on predicting the wax deposition rate is significant for the safe and economical operation of an oil pipeline. This paper adopts the radial basis function neural network to predict the wax deposition rate by considering four main influencing factors, the pipe wall temperature gradient, pipe wall wax crystal solubility coefficient, pipe wall shear stress and crude oil viscosity, by the gray correlational analysis method. MATLAB software is employed to establish the RBF neural network. Compared with the previous literature, favorable consistency exists between the predicted outcomes and the experimental results, with a relative error of 1.5%. It can be concluded that the prediction method of wax deposition rate based on the RBF neural network is feasible.

Understanding the distribution of natural wax in starch-wax films using synchrotron-based FTIR (S-FTIR).

Science.gov (United States)

Muscat, Delina; Tobin, Mark J; Guo, Qipeng; Adhikari, Benu

2014-02-15

High amylose starch-glycerol (HAG) films were produced incorporating beeswax, candelilla wax and carnauba wax in the presence and absence of Tween-80 in order to determine the distribution of wax in the films during the film formation process. The distribution of these waxes within the film was studied using Synchrotron based Fourier Transform Infrared Spectroscopy (S-FTIR) which provided 2D mapping along the thickness of the film. The incorporation of 5% and 10% wax in HAG films produced randomly distributed wax or wax-rich domains, respectively, within these films. Consequently, the addition of these waxes to HAG increased the surface roughness and hydrophobicity of these films. The addition of Tween-80 caused variations in wax-rich bands within the films. The HAG+carnauba wax+Tween-80 films exhibited domed wax-rich domains displayed with high integrated CH2 absorption value at the interior of the films, rougher surface and higher contact angle values than the other films. The S-FTIR 2D images indicated that the distribution of wax in starch-wax films correlated with the roughness and hydrophobicity of the starch-wax films. Copyright © 2013 Elsevier Ltd. All rights reserved.

Accumulation of oil and grease in soils irrigated with greywater and their potential role in soil water repellency.

Science.gov (United States)

Travis, Micheal J; Weisbrod, Noam; Gross, Amit

2008-05-01

The potential impact of oil and grease (O and G) to soils irrigated with greywater (GW) was investigated. Greywater streams were sampled and analyzed for O and G content, along with corresponding GW-irrigated soils. Untreated kitchen GW averaged 200 mg L(-1) O and G, over an order of magnitude more than other GW streams. GW-irrigated soils showed O and G accumulation of up to 200 mg kg(-l) within the first 20-cm of depth. To determine the potential effects of such O and G accumulation on water movement in soil, capillary rise and water drop penetration time (WDPT) experiments were conducted. The results showed up to 60% decrease in capillary rise when sand containing 250 mg kg(-1) O and G was used. Interestingly, no additional reduction in capillary rise was observed at concentrations above 250 mg kg(-1). WDPT was observed to increase linearly with increased O and G content, up to 1000 mg kg(-1). This work demonstrated that O and G in GW used for irrigation can accumulate in soil and may lead to a significant reduction in the soils ability to transmit water.

Biochemical characterization and substrate specificity of jojoba fatty acyl-CoA reductase and jojoba wax synthase.

Science.gov (United States)

Miklaszewska, Magdalena; Banaś, Antoni

2016-08-01

Wax esters are used in industry for production of lubricants, pharmaceuticals and cosmetics. The only natural source of wax esters is jojoba oil. A much wider variety of industrial wax esters-containing oils can be generated through genetic engineering. Biotechnological production of tailor-made wax esters requires, however, a detailed substrate specificity of fatty acyl-CoA reductases (FAR) and wax synthases (WS), the two enzymes involved in wax esters synthesis. In this study we have successfully characterized the substrate specificity of jojoba FAR and jojoba WS. The genes encoding both enzymes were expressed heterologously in Saccharomyces cerevisiae and the activity of tested enzymes was confirmed by in vivo studies and in vitro assays using microsomal preparations from transgenic yeast. Jojoba FAR exhibited the highest in vitro activity toward 18:0-CoA followed by 20:1-CoA and 22:1-CoA. The activity toward other 11 tested acyl-CoAs was low or undetectable as with 18:2-CoA and 18:3-CoA. In assays characterizing jojoba WS combinations of 17 fatty alcohols with 14 acyl-CoAs were tested. The enzyme displayed the highest activity toward 14:0-CoA and 16:0-CoA in combination with C16-C20 alcohols as well as toward C18 acyl-CoAs in combination with C12-C16 alcohols. 20:1-CoA was efficiently utilized in combination with most of the tested alcohols. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Topical Formulation Comprising Fatty Acid Extract from Cod Liver Oil: Development, Evaluation and Stability Studies.

Science.gov (United States)

Ilievska, Biljana; Loftsson, Thorsteinn; Hjalmarsdottir, Martha Asdis; Asgrimsdottir, Gudrun Marta

2016-06-01

The purpose of this study was to develop a pharmaceutical formulation containing fatty acid extract rich in free omega-3 fatty acids such as eicosapentaenoic acid and docosahexaenoic acid for topical use. Although the health benefits of cod liver oil and other fish oils taken orally as a dietary supplement have been acknowledged and exploited, it is clear that their use can be extended further to cover their antibacterial properties. In vitro evaluation showed that 20% (v/v) fatty acid extract exhibits good activity against strains of the Gram-positive bacteria Staphylococcus aureus, Enterococcus faecalis, Streptoccoccus pyogenes and Streptoccoccus pneumonia. Therefore, free polyunsaturated fatty acids from cod liver oil or other fish oils can be used as safe and natural antibacterial agents. In this study, ointment compositions containing free fatty acids as active antibacterial agents were prepared by using various natural waxes and characterized. The effects of different waxes, such as carnauba wax, ozokerite wax, laurel wax, beeswax, rice bran wax, candelilla wax and microcrystalline wax, in the concentration range of 1% to 5% (w/w) on the ointment texture, consistency and stability were evaluated. The results showed significant variations in texture, sensory and rheological profiles. This was attributed to the wax's nature and chain composition. Microcrystalline wax gave the best results but laurel wax, beeswax and rice bran wax exhibited excellent texturing, similar sensory profiles and well-balanced rheological properties.

Chemical aspects of shale and shale oils

Energy Technology Data Exchange (ETDEWEB)

Hackford, J E

1922-01-01

To prove that the kerogen in oil shale is a form of bitumen, several experiments were made with oil shale and a heavy asphaltic oil mixed with fuller's earth. When distilled, both the oil shale and asphalt-impregnated fuller's earth yielded paraffin oil, wax, and hydrogen sulfide (if sulfur was present). Both yielded ammonia if nitrogen was present. The organic material in each was partly isolated by extraction with pyridine and appeared to be the same. Oil shale is a marl that was saturated with oil or through which oil has passed or filtered. The insolubilities of its organic compounds are due to a slightly elevated temperature for a prolonged period and to the retaining effect exerted by the finely divided marl. The marl exerted a selective action on the oil and absorbed the asphaltum, sulfur, and nitrogen compounds from the oil. The class of oil evolved from a shale depended on the nature of the original compounds absorbed. Asphaltenes obtained from crude oil by precipitation with ethyl ether produced distillation products of water, hydrogen sulfide, ammonia, oil, wax, and a carbonaceous residue. Water was formed by decomposition of oxyasphaltenes and hydrogen sulfide by decomposition of thioasphaltenes. Ammonia was evolved during decomposition if lime was present, but if there was not sufficient free lime present, pyridine and pyrrole derivatives were redistilled as such. The oil and wax that resulted from the dry distillation were true decomposition products and equaled about 60 weight-percent of the asphaltenes. The oil and wax content of the mixture varied between 8 and 10 percent. The carbonaceous residue, which represented approximately 40 percent of the original asphaltene, was a decomposition product of the asphaltenes. Geologic comparisons of oil-shale deposits and oil-well fields were also made.

Short Communication - Aquatic Oil Pollution Impact Indicators ...

African Journals Online (AJOL)

Aquatic oil pollution impact indicators such as oil-grease, low dissolved oxygen concentration, increased biochemical oxygen demand, increased water temperature and acidity of the water are associated with aquatic habitat degradation, reduced productivity and or loss of biodiversity. These impact indicators are ...

Physical Characteristics of Tetrahydroxy and Acylated Derivatives of Jojoba Liquid Wax in Lubricant Applications.

Science.gov (United States)

Harry-O'kuru, Rogers E; Biresaw, Girma; Gordon, Sherald; Xu, Jingyuan

2018-01-01

Jojoba liquid wax is a mixture of esters of long-chain fatty acids and fatty alcohols mainly C38:2-C46:2. The oil exhibits excellent emolliency on the skin and, therefore, is a component in many personal care cosmetic formulations. The virgin oil is a component of the seed of the jojoba ( Simmondsia chinensis ) plant which occurs naturally in the Sonora Desert in the United States and northwestern Mexico as well as in the northeastern Sahara desert. The seed contains 50-60% oil by dry weight. The plant has been introduced into Australia, Argentina, and Israel for commercial production of the jojoba oil. As a natural lubricant, we are seeking to explore its potential as a renewable industrial lubricant additive. Thus, we have chemically modified the carbon-carbon double bonds in the oil structure in order to improve its already good resistance to air oxidation so as to enhance its utility as well as its shelf life in nonpersonal care applications. To achieve this goal, we have hydroxylated its -C=C- bonds. Acylation of the resulting hydroxyl moieties has generated short-chain vicinal acyl substituents on the oil which keep the wax liquid, improving its cold flow properties and also protecting it from auto-oxidation and rancidity.

Physical Characteristics of Tetrahydroxy and Acylated Derivatives of Jojoba Liquid Wax in Lubricant Applications

Directory of Open Access Journals (Sweden)

Rogers E. Harry-O’kuru

2018-01-01

Full Text Available Jojoba liquid wax is a mixture of esters of long-chain fatty acids and fatty alcohols mainly C38:2–C46:2. The oil exhibits excellent emolliency on the skin and, therefore, is a component in many personal care cosmetic formulations. The virgin oil is a component of the seed of the jojoba (Simmondsia chinensis plant which occurs naturally in the Sonora Desert in the United States and northwestern Mexico as well as in the northeastern Sahara desert. The seed contains 50–60% oil by dry weight. The plant has been introduced into Australia, Argentina, and Israel for commercial production of the jojoba oil. As a natural lubricant, we are seeking to explore its potential as a renewable industrial lubricant additive. Thus, we have chemically modified the carbon-carbon double bonds in the oil structure in order to improve its already good resistance to air oxidation so as to enhance its utility as well as its shelf life in nonpersonal care applications. To achieve this goal, we have hydroxylated its –C=C– bonds. Acylation of the resulting hydroxyl moieties has generated short-chain vicinal acyl substituents on the oil which keep the wax liquid, improving its cold flow properties and also protecting it from auto-oxidation and rancidity.

Designing maleic anhydride-{alpha}-olifin copolymeric combs as wax crystal growth nucleators

Energy Technology Data Exchange (ETDEWEB)

Soni, Hemant P. [Department of Chemistry, Faculty of Science, The Maharaja Sayajirao University of Baroda, Vadodara-390 002 (India); Kiranbala; Bharambe, D.P. [Department of Applied Chemistry, Faculty of Technology and Engineering, The Maharaja Sayajirao University of Baroda, Vadodara-390 001 (India); Agrawal, K.S. [Department of Petrochemical Technology, Polytechnic, The Maharaja Sayajirao University of Baroda, Vadodara-390 002 (India); Nagar, A. [MH ASSET, ONGC, Mumbai (India)

2010-09-15

Modification of the wax crystal habit is of great practical interest during transportation and processing of crude oil at low temperature. Various pour point depressant (PPD) additives can facilitate this modification by different mechanisms. Comb shaped polymer additives are known to depress the pour point of crude oil by providing different nucleation sites for the precipitation of wax. This paper describes performance based design, synthesis, characterization and evaluation of comb shaped polymeric diesters. Copolymers of maleic anhydride with different unsaturated C{sub 22} esters were synthesized and copolymers then reacted with two unsaturated fatty alcohols. All products were characterized by Fourier Transform Infra Red (FTIR) spectroscopy and Gel Permeation Chromatography (GPC). Rheological properties of crude (with and without additive) were studied by Advance Rheometer AR-500. In this study the additive based on oleic acid was evaluated as good PPD and rheology modifier. (author)

A full-scale UASB reactor for treatment of pig and cattle slaughterhouse wastewater with a high oil and grease content

Directory of Open Access Journals (Sweden)

L. A. S. Miranda

2005-12-01

Full Text Available This paper discusses the performance of an 800m³ full-scale UASB reactor in treating meat-packing plant and slaughterhouse effluents containing high concentrations of oil and grease (O&G (413-645 mg/L, resulting in a COD/O&G ratio of 26-32%. Those macromolecules were considered responsible for the unbalance of the system resulting in a total washout of the biomass. The removal of O&G from the influent using a physicochemical system (coagulation-flocculation improved the physical characteristics of the anaerobic sludge, controlling the biomass washout. Reactor performance was significantly improved when the COD/O&G ratio influent was maintained in the 10%. The COD and O&G removal rates obtained after implantation of the physicochemical system were 70-92% and 27-58%, respectively. The specific methanogenic activity (SMA of the biomass shows towards a tendency stabilisation and adaptation to the substrate influent. Pretreatment of the influent allowed the maximum organic load to be increased (1.46 to 2.43 Kg COD/m³.d and improved the quality of the effluent.

Oil and grease (O&G removal from commercial kitchen waste water using carbonised grass as a key media

Directory of Open Access Journals (Sweden)

Rahmat Siti Nazahiyah

2017-01-01

Full Text Available Oil and grease (O&G are usually found in kitchen waste water. O&G are poorly soluble in water and can cause serious problems during the wastewater treatment. Adsorption is a fundamental process in the treatment of kitchen waste water and very economical. Activated carbon is the most effective adsorbent for this application. Therefore, the aim of the current study is to determine the potential of four materials (i.e. sand, gravel, carbonised grass (CG and clay powder as filter media for O&G removal. The CGs were originated from “Elephant Grass” and it is a fast growing plant with significant potential as carbon. The clay acts as a magnet, drawing the oil molecules out of the water and causing them to attach to the surfaces of the clay. In the current study, two filters were developed with different media materials to get the best percentage removal. Filters 1 and 2 were filled with sand, gravel and CG, and sand, gravel, CG and powder clay, respectively. Three samples were taken during peak hour between April and May 2016. The initial O&G concentration varied from 101.37 mg/l to 248.30 mg/l and the final concentration varied from none to 22.57 mg/l for both filters. The percentage removal (% of O&G were between 90.9 and 97.3 (Filter 1 and between 94.3 and 100 (Filter 2. Overall, both filters could efficiently remove O&G in the waste water and the quality of the carbonised grass proved to be as good as carbon produced from other traditional sources.

Evaluating and modeling biogas production from municipal fat, oil, and grease and synthetic kitchen waste in anaerobic co-digestions.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2011-10-01

The feasibility of using synthetic kitchen waste (KW) and fat, oil, and grease (FOG) as co-substrates in the anaerobic digestion of waste activated sludge (WAS) was investigated using two series of biochemical methane potential (BMP) tests. Ranges of ideal substrate to inoculum (S/I) ratio were determined for the FOG (0.25-0.75) and KW (0.80-1.26) as single substrates in the first experiment. The second experiment, which estimated the methane production performances of FOG and KW as co-substrates for WAS co-digestion, was conducted based on the optimal parameters selected from the results of the first experiment. Results indicated that co-digestions with FOG and KW enhanced methane production from 117±2.02 mL/gTVS (with only WAS) to 418±13.7 mL/gTVS and 324±4.11 mL/gTVS, respectively. FOG exhibited more biogas production than KW as co-substrate. Non-linear regression results showed that co-substrate addition shortened the lag phases of organic biodegradation from 81.8 (with only WAS) to 28.3 h with FOG and 3.90 h with KW. Copyright © 2011 Elsevier Ltd. All rights reserved.

Characterisation of FOGs in grease trap waste from the processing of chickens in Thailand.

Science.gov (United States)

Nitayapat, Nuttakan; Chitprasert, Pakamon

2014-06-01

Industrial firms that kill and process chickens generate wastewater that contains fat, oil, and grease (FOG). The FOGs are located in the fatty waste that is collected by floatation in grease traps. Chemical and physical characterisation of FOGs would provide useful information that would help in the development of methods designed to decrease the extent of pollution caused by disposal of the waste and to utilise commercially some of its lipid constituents. Employing these methods would enhance the profitability and competitive potential of these commercial organisations. Samples of grease trap waste from 14 firms in central Thailand have been examined. Due to the very different schemes of waste management employed by these firms, the physical appearance of their fatty wastes showed considerable variation. The chemical and physical properties of the FOGs present in these wastes showed considerable variation also. Large amounts of free fatty acids (10-70% as oleic acid) were detected in most of the 14 wastes and palmitic, cis-9-oleic, cis,cis-9,12-linoleic, stearic, and palmitoleic acids were the predominant species of free and esterified acids. Most of the FOGs were solid at temperatures below 40 °C. Many of them contained traces of heavy metals (Cu and Pb) and some contained traces of the pesticides dimethoate and cypermethrin. The content of these potentially hazardous substances would have to be considered very carefully before discarding the fatty wastes and during the development of methods designed to isolate their potentially profitable lipid constituents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physicochemical Characteristics and Microbial Quality of an Oil ...

African Journals Online (AJOL)

kg and the lowest value from the river shore sand (620) mg/kg. The high level of oil and grease contamination poses a concern. This therefore, validates the concern that releases of large quantities of oil to aquatic and terrestrial environments ...

Topical Formulation Comprising Fatty Acid Extract from Cod Liver Oil: Development, Evaluation and Stability Studies

Directory of Open Access Journals (Sweden)

Biljana Ilievska

2016-06-01

Full Text Available The purpose of this study was to develop a pharmaceutical formulation containing fatty acid extract rich in free omega-3 fatty acids such as eicosapentaenoic acid and docosahexaenoic acid for topical use. Although the health benefits of cod liver oil and other fish oils taken orally as a dietary supplement have been acknowledged and exploited, it is clear that their use can be extended further to cover their antibacterial properties. In vitro evaluation showed that 20% (v/v fatty acid extract exhibits good activity against strains of the Gram-positive bacteria Staphylococcus aureus, Enterococcus faecalis, Streptoccoccus pyogenes and Streptoccoccus pneumonia. Therefore, free polyunsaturated fatty acids from cod liver oil or other fish oils can be used as safe and natural antibacterial agents. In this study, ointment compositions containing free fatty acids as active antibacterial agents were prepared by using various natural waxes and characterized. The effects of different waxes, such as carnauba wax, ozokerite wax, laurel wax, beeswax, rice bran wax, candelilla wax and microcrystalline wax, in the concentration range of 1% to 5% (w/w on the ointment texture, consistency and stability were evaluated. The results showed significant variations in texture, sensory and rheological profiles. This was attributed to the wax’s nature and chain composition. Microcrystalline wax gave the best results but laurel wax, beeswax and rice bran wax exhibited excellent texturing, similar sensory profiles and well-balanced rheological properties.

Evaluation of different polyolefins as rheology modifier additives in lubricating grease formulations

Energy Technology Data Exchange (ETDEWEB)

Martin-Alfonso, J.E.; Valencia, C.; Sanchez, M.C. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain); Franco, J.M., E-mail: franco@uhu.es [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain); Gallegos, C. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain)

2011-08-15

Highlights: {yields} Evaluation of different polyolefins as modifiers of the rheological properties and mechanical stability of lithium lubricating greases. {yields} The type of polymer, molecular weight, cristallinity degree and vinyl acetate content influences the rheological and thermal response of lubricating greases. {yields} The crystallinity degree, mainly dependent on the nature of the polymer, is the most highly influencing parameter on the rheology of lubricating greases. {yields} The rheological modification exerted by EVA copolymers mainly depends on the vinyl acetate content. - Abstract: The purpose of the present work is to evaluate the effect that different polyolefins, used as additives in small proportions, exert on the rheological properties of standard lithium lubricating greases. Grease formulations containing several polyolefins, differing in nature and molecular weight, were manufactured and rheologically characterized. The influence of the type of polymer, molecular weight, crystallinity degree and vinyl acetate content has been analyzed. Small-amplitude oscillatory shear (SAOS) and viscous flow measurements, as well as calorimetric (DSC) and thermogravimetric (TGA) analysis, were carried out. In general, the addition of polymers such as HDPE, LDPE, LLDPE and PP to lithium lubricating greases significantly increases the values of the rheological parameters analyzed, consistency and mechanical stability. However, the use of polyolefins as rheology modifiers does not significantly affect the friction coefficient determined in a tribological contact. The crystallinity degree, mainly dependent on the nature of the polymer, has been found the most highly influencing parameter on the rheology of the lubricating greases studied. However, the rheological modification exerted by EVA copolymers mainly depends on the vinyl acetate content. Thus, a negative effect in both apparent viscosity and linear viscoelastic functions of greases was obtained when

San Francisco Biofuel Program: Brown Grease to Biodiesel Demonstration

Energy Technology Data Exchange (ETDEWEB)

Jolis, Domènec [San Francisco Public Utilities Commission, San Francisco, CA (United States); Martis, Mary [San Francisco Public Utilities Commission, San Francisco, CA (United States); Jones, Bonnie [San Francisco Public Utilities Commission, San Francisco, CA (United States); Miot, Alex [San Francisco Public Utilities Commission, San Francisco, CA (United States); Ving, Karri [San Francisco Public Utilities Commission, San Francisco, CA (United States); Sierra, Natalie [San Francisco Public Utilities Commission, San Francisco, CA (United States); Niobi, Morayo [San Francisco Public Utilities Commission, San Francisco, CA (United States)

2013-03-01

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas.

A case of butane hash oil (marijuana wax)-induced psychosis.

Science.gov (United States)

Keller, Corey J; Chen, Evan C; Brodsky, Kimberly; Yoon, Jong H

2016-01-01

Marijuana is one of the most widely used controlled substances in the United States. Despite extensive research on smoked marijuana, little is known regarding the potential psychotropic effects of marijuana "wax," a high-potency form of marijuana that is gaining in popularity. The authors present a case of "Mr. B," a 34-year-old veteran who presented with profound psychosis in the setting of recent initiation of heavy, daily marijuana wax use. He exhibited incoherent speech and odd behaviors and appeared to be in a dream-like state with perseverating thoughts about his combat experience. His condition persisted despite treatment with risperidone 4 mg twice a day (BID), but improved dramatically on day 8 of hospitalization with the return of baseline mental function. Following discharge, Mr. B discontinued all marijuana use and did not exhibit the return of any psychotic symptoms. This study highlights the need for future research regarding the potential medical and psychiatric effects of new, high-potency forms of marijuana. Could cannabis have a dose-dependent impact on psychosis? What other potential psychiatric effects could emerge heretofore unseen in lower potency formulations? Given the recent legalization of marijuana, these questions merit timely exploration.

Dewaxing hydrocarbon oils. [British patent

Energy Technology Data Exchange (ETDEWEB)

1933-06-23

In dewaxing hydrocarbon oils such as residium stocks, overhead distillates and crude petroleum or shale oils, by admixing with a liquefied normally gaseous solvent, such as liquefied propane, and cooling to crystallize the wax, the rate of crystallization diminishes rapidly when a certain temperature in an example about 20/sup 0/F is reached. The diminution is prevented during further cooling by removing solvent by evaporation at such a rate that the proporation of solvent in the oil solvent component is maintained at about that existing at the temperature at which the alteration in the rate of crystallization takes place. The evaporation is effected by adjusting the pressure on the mixture, preferably in stages. Solvents for coloring matters and asphaltic compounds, such as carbon disulfide sulfur dioxide, methyl chloride or butyl alcohol may be added to the mixture before crystallization. Chilled solvent may be added to the chilled mixture before separation of the wax in a centrifuge, in order to increase the difference in specific gravity between the wax and the oil-solvent component.

Rheological profiling of organogels prepared at critical gelling concentrations of natural waxes in a triacylglycerol solvent.

Science.gov (United States)

Patel, Ashok R; Babaahmadi, Mehrnoosh; Lesaffer, Ans; Dewettinck, Koen

2015-05-20

The aim of this study was to use a detailed rheological characterization to gain new insights into the gelation behavior of natural waxes. To make a comprehensive case, six natural waxes (differing in the relative proportion of chemical components: hydrocarbons, fatty alcohols, fatty acids, and wax esters) were selected as organogelators to gel high-oleic sunflower oil. Flow and dynamic rheological properties of organogels prepared at critical gelling concentrations (Cg) of waxes were studied and compared using drag (stress ramp and steady flow) and oscillatory shear (stress and frequency sweeps) tests. Although, none of the organogels satisfied the rheological definition of a "strong gel" (G″/G' (ω) ≤ 0.1), on comparing the samples, the strongest gel (highest critical stress and dynamic, apparent, and static yield stresses) was obtained not with wax containing the highest proportion of wax esters alone (sunflower wax, SFW) but with wax containing wax esters along with a higher proportion of fatty alcohols (carnauba wax, CRW) although at a comparatively higher Cg (4%wt for latter compared to 0.5%wt for former). As expected, gel formation by waxes containing a high proportion of lower melting fatty acids (berry, BW, and fruit wax, FW) required a comparatively higher Cg (6 and 7%wt, respectively), and in addition, these gels showed the lowest values for plateau elastic modulus (G'LVR) and a prominent crossover point at higher frequency. The gelation temperatures (TG'=G″) for all the studied gels were lower than room temperature, except for SFW and CRW. The yielding-type behavior of gels was evident, with most gels showing strong shear sensitivity and a weak thixotropic recovery. The rheological behavior was combined with the results of thermal analysis and microstructure studies (optical, polarized, and cryo-scanning electron microscopy) to explain the gelation properties of these waxes.

21 CFR 184.1978 - Carnauba wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Carnauba wax. 184.1978 Section 184.1978 Food and... Substances Affirmed as GRAS § 184.1978 Carnauba wax. (a) Carnauba wax (CAS Reg. No. 008-015-869) is obtained from the leaves and buds of the Brazilian wax palm Copernicia cerifera Martius. The wax is hard...

Some azine and azole derivatives as antioxidant additives for lithium lubricating grease

Directory of Open Access Journals (Sweden)

Reda M. Fikry

2013-06-01

The structure of these compounds has been confirmed using elemental analysis, nuclear magnetic resonance and infrared spectroscopy. On the other hand, lithium lubricating grease was prepared and evaluated according to the National Lubricating Grease Institute (NLGI and Egyptian Standard (ES. The antioxidant compounds were tested for the prepared grease with concentration 0.1 wt.%. The efficiency of these compounds has been determined using total acid number. It was found that the prepared lithium grease resists oxidation reaction in the presence of these compounds. A correlation between the chemical structure of these compounds and their efficiency as antioxidants additives was discussed. Data showed that the efficiency of these compounds as antioxidants decreases in the order: compound I > compound II > compound III.

The Impact of Water on the Yield Stress and Startup Torque of Lubricating Greases

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2017-01-01

Water is one of the most common contaminants in grease lubrication. There are numerous applications where bearings are susceptible to water ingresses such as in the steel, food, and pulp and paper industries. A grease can absorb water to different degrees depending upon the type of grease. The

Immobilized Rhizopus oryzae lipase catalyzed synthesis of palm stearin and cetyl alcohol wax esters: Optimization by Response Surface Methodology

Directory of Open Access Journals (Sweden)

Gargouri Youssef

2011-06-01

Full Text Available Abstract Background Waxes are esters of long-chain fatty acids and long-chain alcohols. Their principal natural sources are animals (sperm whale oil and vegetables (jojoba which are expensive and not easily available. Wax esters synthesized by enzymatic transesterification, using palm stearin as raw material, can be considered as an alternative to natural ones. Results Palm stearin is a solid fraction obtained by fractionation of palm oil. Palm stearin was esterified with cetyl alcohol to produce a mixture of wax esters. A non-commercial immobilized lipase from Rhizopus oryzae was used as biocatalyst. Response surface methodology was employed to determine the effects of the temperature (30-50°C, the enzyme concentration (33.34-300 IU/mL, the alcohol/palm stearin molar ratio (3-7 mol/mol and the substrate concentration (0.06-0.34 g/mL on the conversion yield of palm stearin. Under optimal conditions (temperature, 30°C; enzyme concentration, 300 IU/mL; molar ratio 3 and substrate concentration 0.21 g/mL a high conversion yield of 98.52% was reached within a reaction time of 2 h. Conclusions Response surface methodology was successfully applied to determine the optimum operational conditions for synthesis of palm stearin based wax esters. This study may provide useful tools to develop economical and efficient processes for the synthesis of wax esters.

Catalytic cracking of slack wax with molten mixtures containing aluminum chloride and bromide. [Wax obtained in the process of dewaxing lubricating oils

Energy Technology Data Exchange (ETDEWEB)

Ohtsuka, Y; Oizumi, K; Tamai, Y

1983-09-01

The catalytic cracking of slack wax with molten mixtures of AlCl/sub 3/ (aluminum chloride) and AlBr/sub 3/ (aluminum bromide) was investigated in an atmospheric semi-batch reactor at low temperatures of 100 to 160/sup 0/C. The cracking rate was proportional to the amount of unreacted wax. The conversion at 135/sup 0/C reached 25 wt % under typical reaction conditions. About 95 wt % of the cracking products consisted of isobutane, 2-methylbutane, and methylpentanes, ca. 50% of these isoparaffins being isobutane. The difference in cracking activity between this catalyst and a solid acid catalyst is discussed based on the product distribution. Hardly any reaction took place without HCl, which shows that the presence of HCl is essential for this cracking. The cracking rate increased sharply with an increase in the amount of the catalyst. The rate did not depend on the composition of the AlCl/sub 3//sup -/ AlBr/sub 3/ catalyst, but the product distribution did depend on it and the content of the gasoline fraction in the products increased with an increase in the concentration of AlBr/sub 3/. The cracking residue was characterized by IR and NMR spectroscopy. The results show that the cracking reaction probably occurs heterogeneously at the interface between the liquid wax and the molten catalyst. 3 figures, 4 tables.

Measurement and Prediction of Time-independent and Time-dependent Rheological Behavior of Waxy Crude Oil

OpenAIRE

Yavar Karimi; Ali Reza Solaimany Nazar

2017-01-01

Wax deposition phenomenon changes the rheological behavior of waxy crude oil completely. In the current work, the rheological time-dependent and time-independent behaviors of waxy crude oil samples are studied and flow curve and compliance function are measured for the oil samples with various wax contents at different temperatures. A decrease in temperature and an increase in wax content lead to an increase in the viscosity and yield stress but a significant drop in compliance function. A mo...

Organic pollutant removal from edible oil process wastewater using electrocoagulation

Science.gov (United States)

Sharma, S.; Can, O. T.; Hammed, M.; Nawarathna, D.; Simsek, H.

2018-03-01

Wastewaters generated from vegetable oil industries contain a high concentration of organic pollutants that are detrimental to the aquatic ecosystem. Electrochemical processes are gaining importance in the treatment of inorganic and resistant organic pollutants in wastewaters. In this study, electrocoagulation (EC) was applied to remove organic pollutants and oil and grease from canola oil wastewater using aluminum (Al) and iron (Fe) electrodes. The application of EC in the wastewater achieved more than 80% removal of organic carbon and nearly 100% removal of suspended solids (SS). The effectiveness of EC is influenced mainly by current density, pH, electrolyte (NaCl), electrode contact time and electrode type. It was observed that Al electrode combination yielded better removal at a lesser time compared to that of Fe electrodes. However, varying current densities had its significance in terms of coagulation time only. Increase in current density achieved decrease in coagulation time. Both Al and Fe could remove between 52-59% of oil and grease from canola oil wastewater

BAURAN PEMASARAN PRODUK BARU PELUMAS FOOD GRADE GREASE BERBAHAN DaSAR MINYAK SAWIT

Directory of Open Access Journals (Sweden)

Ali Maksum

2016-12-01

Full Text Available Grease with food grade specification is essentially required on food processing production activities.  The purpose of this study is to develop a new product marketing mix for food grade grease, i.e 1 product priority, 2 pricing priority, 3 distribution priority and 4 advertising priority. This Research was conducted in Sub District Purbalingga and Padamara, Purbalingga regency with respondent SMEs food processing. Analysis of the determination of marketing mix that includes product, price, advertising and distribution using the Analytical Hierarchy Process (AHP. Sampling was purposive random sampling method with a population of 64 SMEs so drawn sample of 20 respondents. Result of the study showed the marketing mix priority which were: (1 advertising priority for the new food grade grease product with an ads that could attract the attention of consumers in order to made the consumers interested, tried, and bought the new food grade lubricating grease products. (2 Price priority for the new food grade grease products which was by determining the moderate prices to compete the competitors' prices while still maintained a high quality. (3 Product priority for new food grade grease product which was producing a qualified product which could withstand the wear of the engine, green colour of the product, a 350 g size packs with a rectangular shape packaging labels. (4 Distribution priority for the new food grade grease product which was a short distribution channels through mobile vendors so that the consumers were able to save costs, and got the product fast and easily

40 CFR 112.11 - Spill Prevention, Control, and Countermeasure Plan requirements for offshore oil drilling...

Science.gov (United States)

2010-07-01

... POLLUTION PREVENTION Requirements for Petroleum Oils and Non-Petroleum Oils, Except Animal Fats and Oils and Greases, and Fish and Marine Mammal Oils; and Vegetable Oils (Including Oils from Seeds, Nuts, Fruits, and... equipped with dump valves which predominantly fail in the closed position and where pollution risk is high...

A Survey on the Removal Efficiency of Fat, Oil and Grease in Shiraz Municipal Wastewater Treatment Plant

Directory of Open Access Journals (Sweden)

Dehghani

2014-12-01

Full Text Available Background Fat, oil and grease (FOG in municipal wastewater treatment plant (MWWTP caused many problems. Objectives This study aimed to determine the removal efficiency of FOG in Shiraz MWWTP. Materials and Methods The removal efficiencies of FOG in the MWWTP were studied from June 2011 to September 2011 in Shiraz (Iran. The influent and effluent wastewater samples were collected in a volume of one liter (4 samples per week and analyzed according to the standard methods. Samples are transferred to the laboratory immediately. The concentration of FOG was determined using the solvent extraction and separating funnel and then compared with the effluent standards. To analyze the data, SPSS (version 11.5, Chi-square test and t test were used. Results The results showed that the FOG amount in input raw sewage in the MWWTP from June 2011 to September 2011 was around 25.5 mg/L and the amount in treated wastewater was about 8.1 mg/L. The FOG removal efficiency in this refinery was about 70% and met the environmental standards for the discharge (less than 10 mg/L (P < 0.05. Conclusions The effluent can be discharged to surface waters or used for irrigation. In order to the FOG concentration met the effluent standards, it is very crucial to control the entrance of industrial wastewater to the municipal wastewater collection networks. Otherwise, the MWWTP should be upgraded and the special techniques used to reduce FOG.

Simulation of temperature-pressure profiles and wax deposition in gas-lift wells

Directory of Open Access Journals (Sweden)

Sevic Snezana

2017-01-01

Full Text Available Gas-lift is an artificial lift method in which gas is injected down the tubing- -casing annulus and enters the production tubing through the gas-lift valves to reduce the hydrostatic pressure of the formation fluid column. The gas changes pressure, temperature and fluid composition profiles throughout the production tubing string. Temperature and pressure drop along with the fluid composition changes throughout the tubing string can lead to wax, asphaltenes and inorganic salts deposition, increased emulsion stability and hydrate formation. This paper presents a new model that can sucesfully simulate temperature and pressure profiles and fluid composition changes in oil well that operates by means of gas-lift. This new model includes a pipe-in-pipe segment (production tubing inside production casing, countercurrent flow of gas-lift gas and producing fluid, heat exchange between gas-lift gas and the surrounding ambient – ground; and gas-lift gas with the fluid in the tubing. The model enables a better understanding of the multiphase fluid flow up the production tubing. Model was used to get insight into severity and locations of wax deposition. The obtained information on wax deposition can be used to plan the frequency and depth of wax removing operations. Model was developed using Aspen HYSYS software.

21 CFR 178.3710 - Petroleum wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Petroleum wax. 178.3710 Section 178.3710 Food and... and Production Aids § 178.3710 Petroleum wax. Petroleum wax may be safely used as a component of nonfood articles in contact with food, in accordance with the following conditions: (a) Petroleum wax is a...

The Field-Dependent Rheological Properties of Magnetorheological Grease Based on Carbonyl-Iron-Particles

Science.gov (United States)

Mohamad, N.; Mazlan, S. A.; Ubaidillah; Choi, Seung-Bok; Nordin, M. F. M.

2016-09-01

This paper presents dynamic viscoelastic properties of magnetorheological (MR) grease under variation of magnetic fields and magnetic particle fractions. The tests to discern the field-dependent properties are undertaken using both rotational and oscillatory shear rheometers. As a first step, the MR grease is developed by dispersing the carbonyl iron (CI) particles into grease medium with a mechanical stirrer. Experimental data are obtained by changing the magnetic field from 0 to 0.7 T at room temperature of 25 °C. It is found that a strong Payne effect limits the linear viscoelastic region of MR grease at strains above 0.1%. The results exhibit a high dynamic yield stress which is equivalent to Bingham plastic rheological model, and show relatively good MR effect at high shear rate of 2000 s-1. In addition, high dispersion of the magnetic particles and good thermal properties are proven. The results presented in this work directly indicate that MR grease is a smart material candidate that could be widely applicable to various fields including vibration control.

Extracting paraffin and mineral waxes

Energy Technology Data Exchange (ETDEWEB)

Carpenter, I C

1930-01-17

In a process for freezing liquids, particularly for precipitating wax from oils such as petroleum or shale oils, the liquid to be treated is cooled first in vessels 10, 11, and 12 by chilled liquid from the final separating tanks 22, then in vessels 13, 14 and 15 by brine cooled by an evaporator 38 and finally in vessels 16,17, 18 directly by the evaporator of a refrigerating plant. The cooling in vessels 10, 11, 12 is regulated by recirculating some of the chilled liquid through the valved pipe 30 while that in tanks 13, 14, 15 is regulated by short-circuiting the brine circulation through a tank 35. Refrigerant vapour from the evaporators in vessels 16, 17, 18 may return through pipe 61 to the compressor or absorber of the plant 45 or it may be withdrawn by pump 58. By the operation of valves A, B, 47, and a valve in pipe 61, the pressures in the evaporators may be varied individually to regulate the cooling in each vessel. Mechanical stirrers are provided in tanks 16, 17, 18.

Plum coatings of lemongrass oil-incorporating carnauba wax-based nanoemulsion.

Science.gov (United States)

Kim, In-Hah; Lee, Hanna; Kim, Jung Eun; Song, Kyung Bin; Lee, Youn Suk; Chung, Dae Sung; Min, Sea C

2013-10-01

Nanoemulsions containing lemongrass oil (LO) were developed for coating plums and the effects of the nanoemulsion coatings on the microbial safety and physicochemical storage qualities of plums during storage at 4 and 25 °C were investigated. The emulsions used for coating were produced by mixing a carnauba wax-based solution (18%, w/w) with LO at various concentrations (0.5% to 4.0%, w/w) using dynamic high pressure processing at 172 MPa. The coatings were evaluated for their ability to inhibit the growth of Salmonella Typhimurium and Escherichia coli O157:H7 and their ability to preserve various physicochemical qualities of plums. Uniform and continuous coatings on plums, formed with stable emulsions, initially inhibited S. Typhimurium and E. coli O157:H7 by 0.2 to 2.8 and 0.8 to 2.7 log CFU/g, respectively, depending on the concentration of LO and the sequence of coating. The coatings did not significantly alter the flavor, fracturability, or glossiness of the plums. The antimicrobial effects of the coatings against S. Typhimurium and E. coli O157:H7 were demonstrated during storage at 4 and 25 °C. The coatings reduced weight loss and ethylene production by approximately 2 to 3 and 1.4 to 4.0 fold, respectively, and also retarded the changes in lightness and the concentration of phenolic compounds in plums during storage. The firmness of coated plums was generally higher than uncoated plums when stored at 4 °C and plum respiration rates were reduced during storage. Coatings containing nanoemulsions of LO have the potential to inhibit Salmonella and E. coli O157:H7 contamination of plums and may extend plum shelf life. Journal of Food Science © 2013 Institute of Food Technologists® No claim to original US government works.

Study on thermal effects & sulfurized additives, in lubricating greases

Science.gov (United States)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to

Measurement and Prediction of Time-independent and Time-dependent Rheological Behavior of Waxy Crude Oil

Directory of Open Access Journals (Sweden)

Yavar Karimi

2017-01-01

Full Text Available Wax deposition phenomenon changes the rheological behavior of waxy crude oil completely. In the current work, the rheological time-dependent and time-independent behaviors of waxy crude oil samples are studied and flow curve and compliance function are measured for the oil samples with various wax contents at different temperatures. A decrease in temperature and an increase in wax content lead to an increase in the viscosity and yield stress but a significant drop in compliance function. A modified Burger model is developed to predict the behavior of the compliance function and a modified Casson model is used to predict the flow curve of the waxy crude oil samples within a vast range of wax contents and temperatures. The proposed Burger and Casson models match with experimental results with R2 of 99.7% and 97.33% respectively.

Anti-inflammatory effects of jojoba liquid wax in experimental models.

Science.gov (United States)

Habashy, Ramy R; Abdel-Naim, Ashraf B; Khalifa, Amani E; Al-Azizi, Mohammed M

2005-02-01

Jojoba [Simmondsia chinensis (Link 1822) Schneider 1907] is an arid perennial shrub grown in several American and African countries. Jojoba seeds, which are rich in liquid wax, were used in folk medicine for diverse ailments. In the current study, the potential anti-inflammatory activity of jojoba liquid wax (JLW) was evaluated in a number of experimental models. Results showed that JLW caused reduction of carrageenin-induced rat paw oedema in addition to diminishing prostaglandin E2 (PGE2) level in the inflammatory exudates. In a test for anti-inflammatory potential utilizing the chick's embryo chroioallantoic membrane (CAM), JLW also caused significant lowering of granulation tissue formation. Topical application of JLW reduced ear oedema induced by croton oil in rats. In the same animal model, JLW also reduced neutrophil infiltration, as indicated by decreased myeloperoxidase (MPO) activity. In addition, JLW ameliorated histopathological changes affected by croton oil application. In the lipopolysaccharide (LPS)-induced inflammation in air pouch in rats, JLW reduced nitric oxide (NO) level and tumor necrosis factor-alpha (TNF-alpha) release. In conclusion, this study demonstrates the effectiveness of JLW in combating inflammation in several experimental models. Further investigations are needed to identify the active constituents responsible for the anti-inflammatory property of JLW.

Rheological Behavior of Carbon Nanotubes as an Additive on Lithium Grease

Directory of Open Access Journals (Sweden)

Alaa Mohamed

2013-01-01

Full Text Available The rheological behaviors of carbon nanotubes (CNTs as an additive on lithium grease at different concentrations were examined under various settings of shear rate, shear stress, and apparent viscosity. The results indicated that the optimum content of the CNTs was 2%. These experimental investigations were evaluated with a Brookfield Programmable Rheometer DV-III ULTRA. The results indicated that the shear, stress and apparent viscosity increase with the increase of CNTs concentration. The microstructure of CNTs and lithium grease was examined by high resolution transmission electron microscope (HRTEM and scanning electron microscope (SEM. The results indicated that the microscopic structure of the lithium grease presents a more regular and homogeneous network structure, with long fibers, which confirms the rheological stability.

Bioremediation of oil contaminated soils

International Nuclear Information System (INIS)

Beeson, D.L.; Hogue, J.I.; Peterson, J.C.; Guerra, G.W.

1994-01-01

The Baldwin Waste Oil Site was an abandoned waste oil recycling facility located in Robstown, Nueces County, Texas. As part of their site assessment activities, the US Environmental Protection Agency (EPA) requested that the Ecology and Environment, Inc., Technical Assistance Team (TAT) investigate the feasibility of using in-situ bioremediation to remediate soils contaminated with oil and grease components, petroleum hydrocarbons, and volatile organic compounds. Bioremediation based on the land treatment concept was tested. The land treatment concept uses techniques to optimize indigenous microbial populations and bring them in contact with the contaminants. The study was designed to collect data upon which to base conclusions on the effectiveness of bioremediation, to demonstrate the effectiveness of bioremediation under field conditions, and to identify potential problems in implementing a full-scale project. Bioremediation effectiveness was monitored through total petroleum hydrocarbons (TPH) and Oil and Grease (O and G) analyses. Site specific treatment goals for the pilot project were concentrations of less than 1% for O and G and less than 10,000 mg/kg for TPH. Based on the reduction of TPH and O and G concentrations and the cost effectiveness of bioremediation based on the land treatment concept, full-scale in-situ bioremediation was initiated by the EPA at the Baldwin Waste Oil Site in February of 1993

Opportunities for Biorenewables in Oil Refineries

Energy Technology Data Exchange (ETDEWEB)

Marker, T.L.

2005-12-19

Abstract: The purpose of this study was to evaluate the potential for using biorenewable feedstocks in oil refineries. Economic analyses were conducted, with support from process modeling and proof of principle experiments, to assess a variety of potential processes and configurations. The study considered two primary alternatives: the production of biodiesel and green diesel from vegetable oils and greases and opportunities for utilization of pyrolysis oil. The study identified a number of promising opportunities for biorenewables in existing or new refining operations.

Effects of air pollutants on epicuticular wax structure

International Nuclear Information System (INIS)

Huttunen, S.

1994-01-01

In xerophytes, like conifers, the epicuticular wax is well developed. Especially in and around stomatal entrances, a thick wax coating is present. Epicuticular waxes are modified by changes in plant growth conditions such as temperature, relative humidity, irradiance, and wind, or acid rain. The fine structure of epicuticular waxes, their chemistry, and ecophysiological function are modified, especially in evergreen, long-lived conifer needles with characteristic crystalline wax structures. During needle flushing and development, wax structure is easily modified. Acid rain-treated Scots pine needles had 50% less epicuticular waxes in early August. Pollution-induced delayed development, destruction, and disturbances have been identified in many plant species. The structural changes in wax crystals are known. Acid rain or polluted air can destroy the crystalloid epicuticular waxes in a few weeks. In Pinus sylvestris, the first sign of pollution effect is the fusion of wax tubes. In Picea abies and P. sitchensis, modifications of crystalloid wax structure are known. In Californian pine trees phenomena of recrystallization of wax tubes on second-year needles were observed after delayed epicuticular wax development in Pinus ponderosa and P. coulteri. Thus, the effects of air pollutants are modified by climate. Accelerated senescence of leaves and needles have been associated with natural and anthropogenic stresses. The accelerated erosion rate of epicuticular waxes has been measured under air pollution conditions. Many short-term air pollution experiments have failed to show any structural changes in epicuticular wax structures. The quantity and quality of needle waxes grown in open-top chambers, glass houses, or polluted air before treatment, differ from field conditions and make it difficult to detect effects of any treatment. (orig.)

21 CFR 872.6890 - Intraoral dental wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Intraoral dental wax. 872.6890 Section 872.6890...) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6890 Intraoral dental wax. (a) Identification. Intraoral dental wax is a device made of wax intended to construct patterns from which custom made metal...

21 CFR 172.888 - Synthetic petroleum wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Synthetic petroleum wax. 172.888 Section 172.888... CONSUMPTION Multipurpose Additives § 172.888 Synthetic petroleum wax. Synthetic petroleum wax may be safely used in or on foods in accordance with the following conditions: (a) Synthetic petroleum wax is a...

Friction torque in thrust ball bearings grease lubricated

Science.gov (United States)

Ianuş, G.; Dumitraşcu, A. C.; Cârlescu, V.; Olaru, D. N.

2016-08-01

The authors investigated experimentally and theoretically the friction torque in a modified thrust ball bearing having only 3 balls operating at low axial load and lubricated with NGLI-00 and NGLI-2 greases. The experiments were made by using spin-down methodology and the results were compared with the theoretical values based on Biboulet&Houpert's rolling friction equations. Also, the results were compared with the theoretical values obtained with SKF friction model adapted for 3 balls. A very good correlation between experiments and Biboulet_&_Houpert's predicted results was obtained for the two greases. Also was observed that the theoretical values for the friction torque calculated with SKF model adapted for a thrust ball bearing having only 3 balls are smaller that the experimental values.

21 CFR 582.1978 - Carnauba wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Carnauba wax. 582.1978 Section 582.1978 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS....1978 Carnauba wax. (a) Product. Carnauba wax. (b) Conditions of use. This substance is generally...

Production of synthetic hydrocarbon lube oil from highly waxy feedstocks

Energy Technology Data Exchange (ETDEWEB)

Xue, Q; Ding, Z; Zheng, Sh; Wu, W

1980-01-01

A feasible way to utilize the low value soft wax is to convert it into synthetic hydrocarbon lube oil by thermal cracking/polymerization route. The first commercial plant for this purpose has been in normal operation since 1970. It has been proved to be economically sound. The antioxidant response of the product polymer oil can be distinctly improved by hydro-refining. It has been found that the vacuum gas oil from highly waxy crude with or without furfural refining can be used as cracking stock. If high viscosity index polymer oil is desired, it is better to use slack wax as the cracking stock.

The potential of restaurant trap grease as biodiesel feedstock

Directory of Open Access Journals (Sweden)

Parichart Hasuntree

2011-10-01

Full Text Available The possibility of using restaurant trap grease as feedstock in the production of biodiesel via acid catalyzed esterificationis explored in this study. Sulfuric acid was used as a catalyst for the esterification reaction of free fatty acid (FFA andmethanol. The FFA levels of restaurant trap greases were reduced from 60.38±2.22 mg KOH/g to 11.60±1.60 mgKOH/g whenconditions for biodiesel production are as follow: methanol-to-FFA ratio of 5:1, 5 wt.% H2SO4, and a reaction temperature at60°C with a reaction time of 60 min. During the acid-catalyzed esterification, the percentage of methyl esters resulting fromconversion of FFA in the obtained product was 83.59±1.51% based on the result of 1H NMR analysis. Data obtained from the23 full factorial designs revealed that methanol-to-FFA ratio term had the most significant effect on the percentage of methylesters, followed by the H2SO4 concentration. Conversely, reaction time between 1 and 3 hours had no significant effect on theesterification of trap greases.

Rheological Behavior of Carbon Nano tubes as an Additive on Lithium Grease

International Nuclear Information System (INIS)

Mohamed, A.; Zaki, M.; Mohamed, A.; Khattab, A.A.; Osman, T.A.

2013-01-01

The rheological behaviors of carbon nano tubes (CNTs) as an additive on lithium grease at different concentrations were examined under various settings of shear rate, shear stress, and apparent viscosity. The results indicated that the optimum content of the CNTs was 2%. These experimental investigations were evaluated with a Brookfield Programmable Rheometer DV-III ULTRA. The results indicated that the shear, stress and apparent viscosity increase with the increase of CNTs concentration. The microstructure of CNTs and lithium grease was examined by high resolution transmission electron microscope (HRTEM) and scanning electron microscope (SEM). The results indicated that the microscopic structure of the lithium grease presents a more regular and homogeneous network structure, with long fibers, which confirms the rheological stability.

Enhancement of biogas production from sewage sludge by addition of grease trap sludge

International Nuclear Information System (INIS)

Grosser, A.; Neczaj, E.

2016-01-01

Highlights: • Addition of grease trap sludge is interesting option for sewage sludge digestion. • Co-digestion of grease trap sludge and sewage sludge improved efficiency of process. • The anaerobic digestion can be carried out at short hydraulic retention time. • Long chain fatty acids concentration was below the ranges for inhibition of anaerobic digestion. - Abstract: Despite having many benefits, a low degree of volatile solids removal as well as long retention time are the main factors limiting the performance of the anaerobic digestion. Co-digestion of sewage sludge with other organic waste (for example fat rich materials) is one of the few potential ways to enhance the performance of the anaerobic digestion. In this article, the effects of adding fatty rich materials on the performance and stability of semi-continuous anaerobic digestion of sewage sludge were investigated on a 6 l laboratory-scale reactor (working volume equal to 5.5 l). The reactor was operated in a semi-continuous mode with a hydraulic retention time of 10 days. The data presented in this paper relate to the period in which the grease trap sludge accounted for 10, 12, 14, 16 and 18% of the mixture on the volatile solids basis. The results clearly indicate that the addition of fat rich materials like grease trap sludge can lead to a satisfactory increase in biogas yield in digester treating sewage sludge. The results showed that co-digestion can enhance the biogas yield by 28–82% compared to anaerobic digestion of sewage sludge alone (control sample). Moreover, the addition of grease trap sludge to digesters resulted in increased volatile solids removal from 44.38% (control sample) to 57.77% (feedstock with 14% addition of grease trap sludge). It was found that the increase of grease trap sludge in the feedstock had a direct impact on the biogas production and methane yield. This proposal has also been confirmed by statistical analysis such as Pearson correlation coefficients and

Evaluation of oil and grease removal by adsorptive polymeric resins in semi-industrial scale: influence of temperature; Avaliacao da remocao de oleos e graxas por resinas polimericas adsorventes em escala semi-industrial: influencia da temperatura

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Luis F.S. de; Silva, Carla M.F. da; Queiros, Yure G.C.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: elucas@ima.ufrj.br

2011-07-01

The aim of this study was to evaluate the performance of polymeric resins packed in a fixed bed eluted in semi-industrial scale for oil and greases removal disposed in synthetic oily water in different temperature conditions. For this work, columns packed with vinyl and acryl polymer-base were tested and their efficiency of oil removal was evaluated by fluorimetry technique in two different temperatures: 25 and 60 deg C, in a flow rate condition of 200 mL/min. The experimental results were very good: the removal efficiencies were above 98% in both cases. At 60 deg C, the system keep the efficiency for a longer time: no significant loss in the efficiency was observed after eluting 1,000 times of the column bed volume at 25 deg C and 2,000, at 60 deg C. This result characterizes a great potential of application in the industry. (author)

21 CFR 186.1555 - Japan wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Japan wax. 186.1555 Section 186.1555 Food and Drugs... Substances Affirmed as GRAS § 186.1555 Japan wax. (a) Japan wax (CAS Reg. No. 8001-39-6), also known as Japan... fruits of the oriental sumac, Rhus succedanea (Japan, Taiwan, and Indo-China), R. vernicifera (Japan...

Structure and Biosynthesis of Branched Wax Compounds on Wild Type and Wax Biosynthesis Mutants of Arabidopsis thaliana.

Science.gov (United States)

Busta, Lucas; Jetter, Reinhard

2017-06-01

The cuticle is a waxy composite that protects the aerial organs of land plans from non-stomatal water loss. The chemical make-up of the cuticular wax mixture plays a central role in defining the water barrier, but structure-function relationships have not been established so far, in part due to gaps in our understanding of wax structures and biosynthesis. While wax compounds with saturated, linear hydrocarbon tails have been investigated in detail, very little is known about compounds with modified aliphatic tails, which comprise substantial portions of some plant wax mixtures. This study aimed to investigate the structures, abundances and biosynthesis of branched compounds on the species for which wax biosynthesis is best understood: Arabidopsis thaliana. Microscale derivatization, mass spectral interpretation and organic synthesis identified homologous series of iso-alkanes and iso-alcohols on flowers and leaves, respectively. These comprised approximately 10-15% of wild type wax mixtures. The abundances of both branched wax constituents and accompanying unbranched compounds were reduced on the cer6, cer3 and cer1 mutants but not cer4, indicating that branched compounds are in part synthesized by the same machinery as unbranched compounds. In contrast, the abundances of unbranched, but not branched, wax constituents were reduced on the cer2 and cer26 mutants, suggesting that the pathways to both types of compounds deviate in later steps of chain elongation. Finally, the abundances of branched, but not unbranched, wax compounds were reduced on the cer16 mutant, and the (uncharacterized) CER16 protein may therefore be controlling the relative abundances of iso-alkanes and iso-alcohols on Arabidopsis surfaces. © The Author 2017. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

ubaegesi@yahoo.co.uk Effects of oil spillage on Soil and Surface

African Journals Online (AJOL)

MICHAEL HORSFALL

Keywords: Tozicity, heavy metals, soil and water, WHO standard, Odoro Ikot Ukanafun, ... temperature, pH, electrical conductivity, oil/grease, copper (Cu), cadmium ... recommended standards, therefore there is need for remediation or clean up ... the soil sample analytical results show that the crude oil has polluted the soil ...

Application of a Thermodynamic Concept for the Analysis of Structural Degradation of Soap Thickened Lubricating Greases

Directory of Open Access Journals (Sweden)

Erik Kuhn

2018-01-01

Full Text Available Lubricating greases are special lubricants with a wide range of application. The tribologically stressed grease is used as tribological system and finally modeled as an open thermodynamic system. This study investigated the phenomenon of self-optimization and applied to the process of shearing a grease. The conditions for self-optimization and the consequences of created dissipative structures are investigated according to the interpreted literature.

Enzyme pretreatment of fats, oil and grease from restaurant waste to prolong septic soil treatment system effectiveness.

Science.gov (United States)

Dong, Younsuk; Safferman, Steven I; Ostahowski, Jeff; Herold, Tom; Panter, Ronald

2017-01-02

When a fast-food restaurant's wastewater containing fats, oil and grease (FOG) is discharged into a collection system, it builds up over time and clogs pipes. Similarly, when such wastewater flows into a septic soil treatment system, it adheres to the surface of inlet pipes, gravel/distribution media and soil, restricting the flow and eventually clogging the septic soil treatment system. In this study, an enzymatic pretreatment system was tested on wastewater from a fast-food restaurant to determine its effectiveness in preventing septic soil treatment system clogging. This system used aeration equipment, baffles and a one-time inoculum that excretes enzymes to reduce the molecular weight and number of double bonds associated with FOG. FOG containing triglycerides having lower molecular weights and fewer double bonds are less sticky. The enzymatic pretreatment system was found to cause these changes as verified by measuring the types of triglycerides (compounds in FOG) using liquid chromatography/mass spectrometry. A unique bench-scale septic soil treatment system (soil trench) was also used. Each contained six soil moisture sensors to enable the determination of moisture saturation trends among the five tested conditions: sanitary wastewater only, a combination of sanitary and kitchen wastewater, enzymatically pretreated sanitary and kitchen wastewater, kitchen wastewater, and enzymatically pretreated kitchen wastewater. For all influent types, a significant amount of FOG and other pollutants were removed, regardless of the initial concentrations. Moisture sensor readings showed differences among the tested conditions, indicating that septic soil treatment system clogging was delayed. Inspection of the influent pipe and gravel at the end of testing verified these differences as did the measurements of volatile solids.

Physical stability, centrifugation tests, and entrapment efficiency studies of carnauba wax-decyl oleate nanoparticles used for the dispersion of inorganic sunscreens in aqueous media.

Science.gov (United States)

Villalobos-Hernández, J R; Müller-Goymann, C C

2006-06-01

Aqueous nanoscale lipid dispersions consisting of carnauba wax-decyl oleate mixtures acting as carriers or accompanying vehicles for inorganic sunscreens such as barium sulfate, strontium carbonate, and titanium dioxide were prepared by high pressure homogenization. For the manufacture of these nanosuspensions, three pigment concentrations (%wt), namely 2, 4, and 6, and two carnauba wax-decyl oleate ratios, 1:1 and 2:1, were used, being some of these combinations chosen for stability studies. Six-month physical stability tests at 4, 20, and 40 degrees C selecting the mean particle size and the polydispersity index of the nanosuspensions as reference parameters were performed. Centrifugation tests of the nanosuspensions assessed by transmission electron microscopy and by the determination of the content of pigments and carnauba wax in the separated fractions were done. The mean particle sizes and the polydispersity indices of the nanosuspensions were not altered after six-month storages at 20 and at 40 degrees C. However, the storage of those at 4 degrees C considerably increased the particle size and polydispersity of the systems, particularly when wax-oil ratios (2:1) were used for the entrapment of the pigments. Transmission electron micrographs of centrifuged samples denoted the presence of three major fractions showing the different types of particles integrated into the nanosuspensions. Furthermore, it was observed that not all the carnauba wax participated in the entrapment of the pigment. Regarding the amount of pigment being encapsulated or bonded by the wax-oil matrices, entrapment efficiencies higher than 85.52% were reported.

Preliminary Study on Treatment of Palm Oil Mill Effluent (POME by Sand Filtration-DBD Plasma System

Directory of Open Access Journals (Sweden)

Ariadi Hazmi

2016-02-01

Full Text Available In the palm oil industry, open ponding, aerobic and anaerobic digestion, physicochemical treatment and membrane filtration are generally applied as conventional treatments of palm oil mill effluent (POME. In this study, a sand filtration-dielectric barrier discharge (DBD system was investigated as an alternative process for treating POME. This system can reduce land usage, processing time and costs compared to conventional systems. The removal efficiency of chemical oxygen demand (COD, biological oxygen demand (BOD5, and oil-grease in relation to the applied voltage were studied. Furthermore, the pH and temperature profiles were investigated. The obtained results indicate that the removal efficiency of COD, BOD5, and oil-grease increased with an increase of the applied voltage. The electrical energy consumption needed is about 10.56 kWh/L of POME.

Sintering of wax for controlling release from pellets.

Science.gov (United States)

Singh, Reena; Poddar, S S; Chivate, Amit

2007-09-14

The purpose of the present study was to investigate incorporation of hydrophobic (ie, waxy) material into pellets using a thermal sintering technique and to evaluate the pellets in vitro for controlled release. Pellets prepared by extrusion-spheronization technology were formulated with a water-soluble drug, microcrystalline cellulose, and carnauba wax. Powdered carnauba wax (4%-20%) prepared by grinding or by emulsification was studied with an attempt to retard the drug release. The inclusion of ground or emulsified carnauba wax did not sustain the release of theophylline for more than 3 hours. Matrix pellets of theophylline prepared with various concentrations of carnauba wax were sintered thermally at various times and temperatures. In vitro drug release profiles indicated an increase in drug release retardation with increasing carnauba wax concentration. Pellets prepared with ground wax showed a higher standard deviation than did those prepared with emulsified wax. There was incomplete release at the end of 12 hours for pellets prepared with 20% ground or emulsified wax. The sintering temperature and duration were optimized to allow for a sustained release lasting at least 12 hours. The optimized temperature and duration were found to be 100 degrees C and 140 seconds, respectively. The sintered pellets had a higher hydrophobicity than did the unsintered pellets. Scanning electron micrographs indicated that the carnauba wax moved internally, thereby increasing the surface area of wax within the pellets.

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tar, and oils containing powdered coal, coke or peat, sulphur in suspension, is effected by passing air or other oxygen-containig gas through a layer of the material of a depth sufficient substantially to deoxygenate the air, the pressure being at or below atmospheric pressure.

A study of the use of bio-based technologies (lubricant and grease) in rail applications.

Science.gov (United States)

2014-05-01

The objective of the project was to study the efficacy of using bio-based lubricant and grease technologies in railroad applications : (locomotives and maintenance of way equipment). Several commercially available rail curve greases were identified a...

Nanoclays for polymer nanocomposites, paints, inks, greases

Indian Academy of Sciences (India)

... rheological modifier for paints, inks and greases, drug delivery vehicle for controlled release of therapeutic agents, and nanoclays for industrial waste water as well as potable water treatment to make further step into green environment. A little amount of nanoclay can alter the entire properties of polymers, paints, inks and ...

Preparation of Jojoba Oil Ester Derivatives for Biodiesel Evaluation

Science.gov (United States)

As a result of the increase in commodity vegetable oil prices, it is imperative that non-food oils should be considered as alternative feedstocks for biodiesel production. Jojoba oil is unusual in that it is comprised of wax esters as opposed to the triglycerides found in typical vegetable oils. A...

Greasing the Wheels of Trade

OpenAIRE

Hendrik P. van Dalen; Aico P. van Vuuren

2003-01-01

This discussion paper resulted in a publication in 'De Economist' , 2005, 153(2), 139-165. How much does a nation spend on resources to 'grease the wheels of trade'? To examine this question the Dutch economy is used as an exemplary case as the Netherlands are known as a nation of traders. This image was derived in the seventeenth century from successes in long distance trade, shipping and financial innovations. Despite its historical background in trading the potential to 'truck and barter' ...

Effect of solvent extraction on Tunisian esparto wax composition

Directory of Open Access Journals (Sweden)

Saâd Inès

2016-08-01

Full Text Available The increase of needs for renewable and vegetable based materials will help to drive the market growth of vegetable waxes. Because of their highly variable composition and physicochemical properties, plant waxes have found numerous applications in the: food, cosmetic, candle, coating, polish etc... The aim of this project is to determine the effect of solvent extraction (petroleum ether and ethanol on Tunisian esparto wax composition. The GC-MS was applied in order to determine the waxes compositions. Then, physicochemical parameters of these two samples of waxes: acid value, saponification value, iodine value and melting point were measured in order to deduct their properties and possible fields of uses. Results showed that esparto wax composition depended on the solvent extraction and that major components of the two samples of waxes were: alkanes, esters of fatty acids and phenols. Furthermore, esparto waxes were characterized by an antioxidant and antibacterial activities but the potential of these activities depended on the solvent of wax extraction.

Isocyanate-functionalized chitin and chitosan as gelling agents of castor oil.

Science.gov (United States)

Gallego, Rocío; Arteaga, Jesús F; Valencia, Concepción; Franco, José M

2013-06-03

The main objective of this work was the incorporation of reactive isocyanate groups into chitin and chitosan in order to effectively use the products as reactive thickening agents in castor oil. The resulting gel-like dispersions could be potentially used as biodegradable lubricating greases. Three different NCO-functionalized polymers were obtained: two of them by promoting the reaction of chitosan with 1,6-hexamethylene diisocyanate (HMDI), and the other by using chitin instead of chitosan. These polymers were characterized through 1H-NMR, FTIR and thermogravimetric analysis (TGA). Thermal and rheological behaviours of the oleogels prepared by dispersing these polymers in castor oil were studied by means of TGA and small-amplitude oscillatory shear (SAOS) measurements. The evolution and values of the linear viscoelasticity functions with frequency for -NCO-functionalized chitosan- and chitin-based oleogels are quite similar to those found for standard lubricating greases. In relation to long-term stability of these oleogels, no phase separation was observed and the values of viscoelastic functions increase significantly during the first seven days of ageing, and then remain almost constant. TGA analysis showed that the degradation temperature of the resulting oleogels is higher than that found for traditional lubricating greases.

An Electrochemical Processing Strategy for Improving Tribological Performance of Aisi 316 Stainless Steel Under Grease Lubrication

Science.gov (United States)

Zou, Jiaojuan; Li, Maolin; Lin, Naiming; Zhang, Xiangyu; Qin, Lin; Tang, Bin

2014-12-01

In order to improve the tribological performance of AISI 316 stainless steel (316 SS) under grease lubrication, electrochemical processing was conducted on it to obtain a rough (surface texturing-like) surface by making use of the high sensitivity of austenitic stainless steel to pitting corrosion in Cl--rich environment. Numerous corrosion pits or micro-ditches acted as micro-reservoirs on the obtained surface. While the grease could offer consistent lubrication, and then improve the tribological performance of 316 SS. Tribological behaviors of raw 316 SS and the treated sample were measured using a reciprocating type tribometer sliding against GCr15 steel counterpart under dry and grease lubrication conditions. The results showed that the mass losses of the two samples were in the same order of magnitude, and the raw sample exhibited lower friction coefficient in dry sliding. When the tests were conducted under grease lubrication condition, the friction coefficients and mass losses of the treated sample were far lower than those of the raw 316 SS. The tribological performance of 316 SS under grease lubrication was drastically improved after electrochemical processing.

Increased production of wax esters in transgenic tobacco plants by expression of a fatty acid reductase:wax synthase gene fusion.

Science.gov (United States)

Aslan, Selcuk; Hofvander, Per; Dutta, Paresh; Sun, Chuanxin; Sitbon, Folke

2015-12-01

Wax esters are hydrophobic lipids consisting of a fatty acid moiety linked to a fatty alcohol with an ester bond. Plant-derived wax esters are today of particular concern for their potential as cost-effective and sustainable sources of lubricants. However, this aspect is hampered by the fact that the level of wax esters in plants generally is too low to allow commercial exploitation. To investigate whether wax ester biosynthesis can be increased in plants using transgenic approaches, we have here exploited a fusion between two bacterial genes together encoding a single wax ester-forming enzyme, and targeted the resulting protein to chloroplasts in stably transformed tobacco (Nicotiana benthamiana) plants. Compared to wild-type controls, transgenic plants showed both in leaves and stems a significant increase in the total level of wax esters, being eight-fold at the whole plant level. The profiles of fatty acid methyl ester and fatty alcohol in wax esters were related, and C16 and C18 molecules constituted predominant forms. Strong transformants displayed certain developmental aberrations, such as stunted growth and chlorotic leaves and stems. These negative effects were associated with an accumulation of fatty alcohols, suggesting that an adequate balance between formation and esterification of fatty alcohols is crucial for a high wax ester production. The results show that wax ester engineering in transgenic plants is feasible, and suggest that higher yields may become achieved in the near future.

Wax-bonding 3D microfluidic chips

KAUST Repository

Gong, Xiuqing; Yi, Xin; Xiao, Kang; Li, Shunbo; Kodzius, Rimantas; Qin, Jianhua; Wen, Weijia

2013-01-01

We report a simple, low-cost and detachable microfluidic chip incorporating easily accessible paper, glass slides or other polymer films as the chip materials along with adhesive wax as the recycling bonding material. We use a laser to cut through the paper or film to form patterns and then sandwich the paper and film between glass sheets or polymer membranes . The hot-melt adhesive wax can realize bridge bonding between various materials, for example, paper, polymethylmethacrylate (PMMA) film, glass sheets, or metal plate. The bonding process is reversible and the wax is reusable through a melting and cooling process. With this process, a three-dimensional (3D) microfluidic chip is achievable by vacuating and venting the chip in a hot-water bath. To study the biocompatibility and applicability of the wax-based microfluidic chip, we tested the PCR compatibility with the chip materials first. Then we applied the wax-paper based microfluidic chip to HeLa cell electroporation (EP ). Subsequently, a prototype of a 5-layer 3D chip was fabricated by multilayer wax bonding. To check the sealing ability and the durability of the chip, green fluorescence protein (GFP) recombinant Escherichia coli (E. coli) bacteria were cultured, with which the chemotaxis of E. coli was studied in order to determine the influence of antibiotic ciprofloxacin concentration on the E. coli migration.

Wax-bonding 3D microfluidic chips

KAUST Repository

Gong, Xiuqing

2013-10-10

We report a simple, low-cost and detachable microfluidic chip incorporating easily accessible paper, glass slides or other polymer films as the chip materials along with adhesive wax as the recycling bonding material. We use a laser to cut through the paper or film to form patterns and then sandwich the paper and film between glass sheets or polymer membranes . The hot-melt adhesive wax can realize bridge bonding between various materials, for example, paper, polymethylmethacrylate (PMMA) film, glass sheets, or metal plate. The bonding process is reversible and the wax is reusable through a melting and cooling process. With this process, a three-dimensional (3D) microfluidic chip is achievable by vacuating and venting the chip in a hot-water bath. To study the biocompatibility and applicability of the wax-based microfluidic chip, we tested the PCR compatibility with the chip materials first. Then we applied the wax-paper based microfluidic chip to HeLa cell electroporation (EP ). Subsequently, a prototype of a 5-layer 3D chip was fabricated by multilayer wax bonding. To check the sealing ability and the durability of the chip, green fluorescence protein (GFP) recombinant Escherichia coli (E. coli) bacteria were cultured, with which the chemotaxis of E. coli was studied in order to determine the influence of antibiotic ciprofloxacin concentration on the E. coli migration.

Bioremediation of petrochemical sludge from oil refining operations

International Nuclear Information System (INIS)

Prince, M.J.; Sambasivam, Yasodha

1991-01-01

Petroleum refineries have historically produced large quantities of hydrocarbon sludge as a waste product. A common past practice for disposal of this material was to deposit it in open pits. These hazardous waste sites now require remediation to meet current environmental regulations. This report will present data from a feasibility study on bioremediation for one such site. Data will be presented on the characteristics and composition of the crude sludge including organic analysis by GC/MS techniques, loss on ignition, TOC pH, oil and grease levels, metals content by atomic adsorption and bacteria plate counts. The effectiveness of bioremediation will be examined using data from shaker flask studies with indigenous and other bacteria sources. Key parameters being monitored will include toxicity using a Microtox assay, oil and grease levels, and the concentration of individual chemical species using GC/MS analysis. Biological data such as bacteria growth rates and nutrient uptake rates will also be presented and compared to biodegradation rates

Aplikasi Wax Sebagai Salah Satu Material Di Bidang Kedokteran Gigi

OpenAIRE

Rika Jamilah Israwati Lubis

2008-01-01

Wax merupakan salah satu bahan termoplastik yang terdiri dari berbagai bahan organis dan bahan alami sehingga membuatnya sebagai bahan dengan sifat-sifat yang sangat berguna. Unsur-unsur pokok dental wax terdiri dari 3 suraber utama, yaitu : mineral, serangga (hewani), dan sayur-sayuran (tumbuh-tumbuhan). Wax yang berasal dari bahan mineral diantaranya adalah paraffin wax dan microcrystallin wax yang diperoleh dari hasil residu petroleum melalui proses destilasi. Wax yang berasal dari serangg...

Chemical composition of raw and deresinated peat waxes

Energy Technology Data Exchange (ETDEWEB)

Bel' kevich, P I; Ivanova, L A; Piskunova, T A; Tserlyukevich, Ya V; Yurkevich, E A

1980-01-01

Research was conducted using absorption chromatography and spectroscopy to study the changes in the chemical composition of raw peat wax taking place in the deresination process. Characteristics of the raw, deresinated waxes and resins removed are given. The fractions obtained showed that both raw and deresinated wax contain the same basic compound classes: hydrocarbons, alcohols, complex ether and acids; but their proportions in the waxes are different. After deresination most of the dark-colored polyfunctional compounds, a portion of the soluble unsaturated hydrocarbons and alcohols, and all the sterenes transfer into the resin. This causes the light color and specific physical properties of deresinated wax. (13 refs.) (In Russian)

Recyclable zein-coated kraft paper and linerboard

Science.gov (United States)

Nicholas Parris; Marguerite Sykes; Leland C. Dickey; Jack L. Wiles; Thomas J. Urbanik; Peter H. Cooke

2002-01-01

Recyclability of kraft paper and linerboard coated with commercial zein and paraffin wax or a zein-lipid mixture was evaluated using conventional recycling processes. Zein, an alcohol-soluble protein from corn, exhibits both grease and water vapor barrier properties. Strength properties, grease resistance, and water vapor barrier proper-ties were measured on handsheets...

Evaluation of castor oil samples for potential toxin contamination

Science.gov (United States)

Castor oil and its derivatives are widely used as a chemical feedstock for production of lubricants and greases, and for engineering plastics, plasticizers and surfactants. They also have wide application in consumer goods such as lipstick, deodorants and medicinal products. Due to concerns about th...

Effects of air pollutants on epicuticular wax chemical composition

International Nuclear Information System (INIS)

Percy, K.E.; McQuattie, C.J.; Rebbeck, J.A.

1994-01-01

There are numerous reports in the literature of modifications to epicuticular wax structure as a consequence of exposure to air pollutants. Most authors have used scanning electron microscopy (SEM) to describe changes in wax crystallite morphology or distribution. ''Erosion'' or ''weathering'' of crystalline structure into an amorphous state is the most common observation, particularly in the case of conifer needles having the characteristic tube crystallites comprised of nonacosan-10-ol. Wax structure is largely determined by its chemical composition. Therefore, many of the reported changes in wax structure due to air pollutants probably arise from direct interactions between pollutants such as ozone and wax biosynthesis. The literature describing changes in wax composition due to pollutants is briefly reviewed. New evidence is introduced in support of the hypothesis for a direct interaction between air pollutants and epicuticular wax Biosynthesis. (orig.)

75 FR 63200 - Petroleum Wax Candles From China

Science.gov (United States)

2010-10-14

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-282 (Third Review)] Petroleum Wax Candles... five-year review concerning the antidumping duty order on petroleum wax candles from China. SUMMARY... antidumping duty order on petroleum wax candles from China would be likely to lead to continuation or...

75 FR 80843 - Petroleum Wax Candles From China

Science.gov (United States)

2010-12-23

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-282 (Third Review)] Petroleum Wax Candles... Tariff Act of 1930 (19 U.S.C. 1675(c)), that revocation of the antidumping duty order on petroleum wax... contained in USITC Publication 4207 (December 2010), entitled Petroleum Wax Candles from China...

Dental wax decreases calculus accumulation in small dogs.

Science.gov (United States)

Smith, Mark M; Smithson, Christopher W

2014-01-01

A dental wax was evaluated after unilateral application in 20 client-owned, mixed and purebred small dogs using a clean, split-mouth study model. All dogs had clinical signs of periodontal disease including plaque, calculus, and/or gingivitis. The wax was randomly applied to the teeth of one side of the mouth daily for 30-days while the contralateral side received no treatment. Owner parameters evaluated included compliance and a subjective assessment of ease of wax application. Gingivitis, plaque and calculus accumulation were scored at the end of the study period. Owners considered the wax easy to apply in all dogs. Compliance with no missed application days was achieved in 8 dogs. The number of missed application days had no effect on wax efficacy. There was no significant difference in gingivitis or plaque accumulation scores when comparing treated and untreated sides. Calculus accumulation scores were significantly less (22.1 %) for teeth receiving the dental wax.

Optimization of natural lipstick formulation based on pitaya (Hylocereus polyrhizus) seed oil using D-optimal mixture experimental design.

Science.gov (United States)

Kamairudin, Norsuhaili; Gani, Siti Salwa Abd; Masoumi, Hamid Reza Fard; Hashim, Puziah

2014-10-16

The D-optimal mixture experimental design was employed to optimize the melting point of natural lipstick based on pitaya (Hylocereus polyrhizus) seed oil. The influence of the main lipstick components-pitaya seed oil (10%-25% w/w), virgin coconut oil (25%-45% w/w), beeswax (5%-25% w/w), candelilla wax (1%-5% w/w) and carnauba wax (1%-5% w/w)-were investigated with respect to the melting point properties of the lipstick formulation. The D-optimal mixture experimental design was applied to optimize the properties of lipstick by focusing on the melting point with respect to the above influencing components. The D-optimal mixture design analysis showed that the variation in the response (melting point) could be depicted as a quadratic function of the main components of the lipstick. The best combination of each significant factor determined by the D-optimal mixture design was established to be pitaya seed oil (25% w/w), virgin coconut oil (37% w/w), beeswax (17% w/w), candelilla wax (2% w/w) and carnauba wax (2% w/w). With respect to these factors, the 46.0 °C melting point property was observed experimentally, similar to the theoretical prediction of 46.5 °C. Carnauba wax is the most influential factor on this response (melting point) with its function being with respect to heat endurance. The quadratic polynomial model sufficiently fit the experimental data.

Optimization of Natural Lipstick Formulation Based on Pitaya (Hylocereus polyrhizus Seed Oil Using D-Optimal Mixture Experimental Design

Directory of Open Access Journals (Sweden)

Norsuhaili Kamairudin

2014-10-01

Full Text Available The D-optimal mixture experimental design was employed to optimize the melting point of natural lipstick based on pitaya (Hylocereus polyrhizus seed oil. The influence of the main lipstick components—pitaya seed oil (10%–25% w/w, virgin coconut oil (25%–45% w/w, beeswax (5%–25% w/w, candelilla wax (1%–5% w/w and carnauba wax (1%–5% w/w—were investigated with respect to the melting point properties of the lipstick formulation. The D-optimal mixture experimental design was applied to optimize the properties of lipstick by focusing on the melting point with respect to the above influencing components. The D-optimal mixture design analysis showed that the variation in the response (melting point could be depicted as a quadratic function of the main components of the lipstick. The best combination of each significant factor determined by the D-optimal mixture design was established to be pitaya seed oil (25% w/w, virgin coconut oil (37% w/w, beeswax (17% w/w, candelilla wax (2% w/w and carnauba wax (2% w/w. With respect to these factors, the 46.0 °C melting point property was observed experimentally, similar to the theoretical prediction of 46.5 °C. Carnauba wax is the most influential factor on this response (melting point with its function being with respect to heat endurance. The quadratic polynomial model sufficiently fit the experimental data.

Rheological Properties of Extreme Pressure Greases Measured Using a Process Control Rheometer

DEFF Research Database (Denmark)

Glasscock, Julie; Smith, Robin S.

2012-01-01

A new process control rheometer (PCR) designed for use in industrial process flows has been used to measure the rheological properties of three extreme-pressure greases. The rheometer is a robust yet sensitive instrument designed to operate in an industrial processing environment in either in......-line or on-line configurations. The PCR was able to measure the rheological properties including the elastic modulus, viscous modulus, and complex viscosity of the greases which in an industrial flow application could be used as variables in a feedback system to control the process and the quality...

Rheological Investigation on the Effect of Shear and Time Dependent Behavior of Waxy Crude Oil

Directory of Open Access Journals (Sweden)

Japper-Jaafar A.

2014-07-01

Full Text Available Rheological measurements are essential in transporting crude oil, especially for waxy crude oil. Several rheological measurements have been conducted to determine various rheological properties of waxy crude oil including the viscosity, yield strength, wax appearance temperature (WAT, wax disappearance temperature (WDT, storage modulus and loss modulus, amongst others, by using controlled stress rheometers. However, a procedure to determine the correct parameters for rheological measurements is still unavailable in the literature. The paper aims to investigate the effect of shear and time dependent behaviours of waxy crude oil during rheological measurements. It is expected that the preliminary work could lead toward a proper rheological measurement guideline for reliable rheological measurement of waxy crude oil.

Benzoxazole and Benzothiazole Antirust Greases. Work Unit Directive (WUD) 51

National Research Council Canada - National Science Library

Christian, John

1980-01-01

...) and polytetrafluoroethylene (PTFE) thickeners. Testing has shown that one percent concentrations of the additives in the grease formulations provide inhibition against rusting of ferrous metal components under conditions of high humidity...

Identification of CYP1A inducing compounds in crude oil

Energy Technology Data Exchange (ETDEWEB)

Khan, C.W.; Hodson, P.V. [Queen' s Univ., Kingston, ON (Canada). Dept. of Biology; Hollebone, B.P.; Wang, Z. [Environment Canada, Ottawa, ON (Canada). Environmental Technology Advancement Directorate; Brown, R.S. [Queen' s Univ., Kingston, ON (Canada). Dept. of Chemistry

2004-07-01

One of the major sources of polycyclic aromatic hydrocarbons (PAHs) in aquatic ecosystems is crude oil. PAHs are responsible for developmental malformations in the early life stages of fish. The induction of CYP1A enzyme is characteristic of developmental toxicity caused by crude oil. As such, it is an effective biomarker of PAH uptake. It is not known which PAHs cause toxicity because of the complex chemical composition of crude oil. In this study, an approach called Toxicity Identification and Evaluation (TIE) was used with different crude oils to separate bioavailable PAHs into petroleum sub-fractions. The extent of CYP1A induction in rainbow trout was measured after 48 hour exposures to each fraction. Low temperature vacuum distillation was used to create white gas, kerosene, coal tar/bitumen and wax fractions. Hepatic CYP1A activity was induced by whole oil and some fractions. The highest PAH concentration was found in the coal tar/bitumen fraction which accounted for most CYP1A induction in whole oil. The wax fraction also caused moderate CYP1A induction, but the white gas fraction did not cause any CYP1A induction. The hypothesis that alkyl PAH may be the most significant source of CYP1A inducers in the coal tar/bitumen fraction was supported by chemical analysis of CYP1A induction potency. Results showed that benzo[a]pyrene accounts for nearly all of the CYP1A induction caused by the wax fraction.

Mechanical properties of carving wax with various Ca-bentolite filter composition

Directory of Open Access Journals (Sweden)

Widjijono Widjijono

2009-09-01

Full Text Available Background: The carving wax is used as a medium in dental anatomy study. This wax composes of many waxes and sometimes a filler is added. Carving wax is not sold in Indonesian market. Whereas the gradients of carving wax such as beeswax, paraffin and bentonite are abundant in Indonesia. Based on that fact, to make high quality and standard,the exact composition if this carving wax should be known. Purpose: The aim of this study was to investigate the effect of carving wax composition with Ca-bentonite filler on the melting point, hardness, and thermal expansion. Methods: Five carving wax compositions were made with paraffin, Ca-bentonite, carnauba wax, and beeswax in ratio (% weight: 50:20:25:5 (KI, 55:15:25:5 (KII, 60:10:25:5 (KIII, 65:5:25:5 (KIV, 70:0:25:5(KV. All components were melted, then poured into the melting point, hardness, and thermal expansion moulds (n = 5. Three carving wax properties were tested: melting point by melting point apparatus; hardness by penetrometer; thermal expansion by digital sliding caliper. The data were analyzed statistically using One-Way ANOVA and LSD0.05. Result: The Ca-bentonite addition influenced the melting point and thermal expansion of carving wax with significant differences between KI and other groups (p < 0.05. Ca-bentonite addition influenced the carving wax hardness and the mean differences among the groups were significant (p < 0.05. Conclusion: Ca-bentonite filler addition on the composition of carving wax influenced the physical and mechanical properties. The carving wax with high Ca-bentonite concentration had high melting point and hardness, but low thermal expansion.

In vivo evaluation of insect wax for hair growth potential

Science.gov (United States)

Ma, Jinju

2018-01-01

Insect wax is secreted by Ericerus pela Chavanness. It has been traditionally used to treat hair loss in China, but few reports have been published on the hair growth-promoting effect of insect wax. In this work, we examined the hair growth-promoting effects of insect wax on model animals. Different concentrations of insect wax were topically applied to the denuded backs of mice, and 5% minoxidil was applied topically as a positive control. We found that insect wax significantly promoted hair growth in a dose-dependent manner, 45% and 30% insect wax both induced hair to regrow, while less visible hair growth was observed in blank controls on the 16th day. The experimental areas treated with 45% and 30% insect wax exhibited significant differences in hair scores compared to blank controls, and hair lengths in the 45% and 30% insect wax group was significantly longer than in blank controls on the 16th and 20th days. There were no new hair follicles forming in the treated areas, and the hair follicles were prematurely converted to the anagen phase from the telogen phase in experimental areas treated with 45% and 30% insect wax. Both 45% and 30% insect wax upregulated vascular endothelial growth factor expression. The results indicated that 45% and 30% insect wax showed hair growth-promoting potential approximately as potent as 5% minoxidil by inducing the premature conversion of telogen-to-anagen and by prolonging the mature anagen phase rather than increasing the number of hair follicles, which was likely related to the upregulation of VEGF expression. The dissociative policosanol in insect wax was considered the key ingredient most likely responsible for the hair growth promoting potential. PMID:29438422

In vivo evaluation of insect wax for hair growth potential.

Directory of Open Access Journals (Sweden)

Jinju Ma

Full Text Available Insect wax is secreted by Ericerus pela Chavanness. It has been traditionally used to treat hair loss in China, but few reports have been published on the hair growth-promoting effect of insect wax. In this work, we examined the hair growth-promoting effects of insect wax on model animals. Different concentrations of insect wax were topically applied to the denuded backs of mice, and 5% minoxidil was applied topically as a positive control. We found that insect wax significantly promoted hair growth in a dose-dependent manner, 45% and 30% insect wax both induced hair to regrow, while less visible hair growth was observed in blank controls on the 16th day. The experimental areas treated with 45% and 30% insect wax exhibited significant differences in hair scores compared to blank controls, and hair lengths in the 45% and 30% insect wax group was significantly longer than in blank controls on the 16th and 20th days. There were no new hair follicles forming in the treated areas, and the hair follicles were prematurely converted to the anagen phase from the telogen phase in experimental areas treated with 45% and 30% insect wax. Both 45% and 30% insect wax upregulated vascular endothelial growth factor expression. The results indicated that 45% and 30% insect wax showed hair growth-promoting potential approximately as potent as 5% minoxidil by inducing the premature conversion of telogen-to-anagen and by prolonging the mature anagen phase rather than increasing the number of hair follicles, which was likely related to the upregulation of VEGF expression. The dissociative policosanol in insect wax was considered the key ingredient most likely responsible for the hair growth promoting potential.

Statistical Optimization of Sustained Release Venlafaxine HCI Wax Matrix Tablet.

Science.gov (United States)

Bhalekar, M R; Madgulkar, A R; Sheladiya, D D; Kshirsagar, S J; Wable, N D; Desale, S S

2008-01-01

The purpose of this research was to prepare a sustained release drug delivery system of venlafaxine hydrochloride by using a wax matrix system. The effects of bees wax and carnauba wax on drug release profile was investigated. A 3(2) full factorial design was applied to systemically optimize the drug release profile. Amounts of carnauba wax (X(1)) and bees wax (X(2)) were selected as independent variables and release after 12 h and time required for 50% (t(50)) drug release were selected as dependent variables. A mathematical model was generated for each response parameter. Both waxes retarded release after 12 h and increases the t(50) but bees wax showed significant influence. The drug release pattern for all the formulation combinations was found to be approaching Peppas kinetic model. Suitable combination of two waxes provided fairly good regulated release profile. The response surfaces and contour plots for each response parameter are presented for further interpretation of the results. The optimum formulations were chosen and their predicted results found to be in close agreement with experimental findings.

Effects of ultrasonic and thermo-chemical pre-treatments on methane production from fat, oil and grease (FOG) and synthetic kitchen waste (KW) in anaerobic co-digestion.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2013-02-01

The effects of ultrasonic and thermo-chemical pre-treatments on the methane production potential of anaerobic co-digestion with synthetic kitchen waste (KW) or fat, oil and grease (FOG) were investigated. Non-linear regressions were fitted to accurately assess and compare the methane production from co-digestion under the various pre-treatment conditions and to achieve representative simulations and predictions. Ultrasonic pre-treatment was not found to improve methane production effectively from either FOG co-digestion or KW co-digestions. Thermo-chemical pre-treatment could increase methane production yields from both FOG and KW co-digestions. COD solubilization was found to effectively represent the effects of pre-treatment. A comprehensive evaluation indicated that the thermo-chemical pre-treatments of pH=10, 55°C and pH=8, 55°C provided the best conditions to increase methane production from FOG and KW co-digestions, respectively. The most effective enhancement of biogas production (288±0.85mLCH(4)/g TVS) was achieved from thermo-chemically pre-treated FOG co-digestion, which was 9.9±1.5% higher than FOG co-digestion without thermo-chemical pre-treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Empirical modeling of a dewaxing system of lubricant oil using Artificial Neural Network (ANN); Modelagem empirica de um sistema de desparafinacao de oleo lubrificante usando redes neurais artificiais

Energy Technology Data Exchange (ETDEWEB)

Fontes, Cristiano Hora de Oliveira; Medeiros, Ana Claudia Gondim de; Silva, Marcone Lopes; Neves, Sergio Bello; Carvalho, Luciene Santos de; Guimaraes, Paulo Roberto Britto; Pereira, Magnus; Vianna, Regina Ferreira [Universidade Salvador (UNIFACS), Salvador, BA (Brazil). Dept. de Engenharia e Arquitetura]. E-mail: paulorbg@unifacs.br; Santos, Nilza Maria Querino dos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)]. E-mail: nilzaq@petrobras.com.br

2003-07-01

The MIBK (m-i-b-ketone) dewaxing unit, located at the Landulpho Alves refinery, allows two different operating modes: dewaxing ND oil removal. The former is comprised of an oil-wax separation process, which generates a wax stream with 2 - 5% oil. The latter involves the reprocessing of the wax stream to reduce its oil content. Both involve a two-stage filtration process (primary and secondary) with rotative filters. The general aim of this research is to develop empirical models to predict variables, for both unit-operating modes, to be used in control algorithms, since many data are not available during normal plant operation and therefore need to be estimated. Studies have suggested that the oil content is an essential variable to develop reliable empirical models and this work is concerned with the development of an empirical model for the prediction of the oil content in the wax stream leaving the primary filters. The model is based on a feed forward Artificial Neural Network (ANN) and tests with one and two hidden layers indicate very good agreement between experimental and predicted values. (author)

Preliminary research on measuring grease in petroleum pipeline using fast neutron transmission method

International Nuclear Information System (INIS)

Liu Qingwei; Liu Shengkang; Zhang Zhiping; Ding Xiaoping

2006-01-01

The principle, experiment and conclusion on the grease stain measurement using fast neutron are reported. The experiment equipment consist of 241 Am-Be fast neutron source, ZnS detector and BH1224 multichannel spectrometer. Paraffin is used instead of real grease stain. Steel plates are used instead of pipeline. The results of the experiment indicate that there is a good linearship between the logarithm of the reciprocal of the neutron transmissivity and the paraffin thickness. The measuring accuracy of the paraffin thickness is 0.6 mm in this experiment. (authors)

Effects of UV-B radiation on wax biosynthesis

International Nuclear Information System (INIS)

Barnes, J.; Paul, N.; Percy, K.; Broadbent, P.; McLaughlin, C.; Mullineaux, P.; Creissen, G.; Wellburn, A.

1994-01-01

Two genotypes of tobacco (Nicotiana tabacum L.) were exposed in controlled environment chambers to three levels of biologically effective ultraviolet-B radiation (UV-B BE ; 280-320nm): 0, 4.54 (ambient) and 5.66 (∼ 25% enhancement) kJ m -2 d -1 . After 28 days, the quantity of wax deposited on leaf surfaces was determined gravimetrically; epicuticular wax chemical composition was determined by capillary gas chromatography with homologue assignments confirmed by gas chromatography-mass spectrometry. Leaf wettability was assessed by measuring the contact angle of water droplets placed on leaf surfaces. Tobacco wax consisted of three major hydrocarbon classes: Straight-chain alkanes (C 27 -C 33 ) which comprised ∼ 59% of the hydrocarbon fraction, containing a predominance of odd-chain alkanes with C 31 as the most abundant homologue; branched-chain alkanes (C 25 -C 32 ) which comprised ∼38% of the hydrocarbon fraction with anteiso 3-methyltriacontane (C 30 ) as the predominant homologue; and fatty acids (C 14 -C 18 ) which comprised ∼ 3% of the wax. Exposure to enhanced UV-B radiation reduced the quantity of wax on the adaxial surface of the transgenic mutant, and resulted in marked changes in the chemical composition of the wax on the exposed leaf surface. Enhanced UV-B decreased the quantity of straight-chain alkanes, increased the quantity of branched-chain alkanes and fatty acids, and resulted in shifts toward shorter straight-chain lengths. Furthermore, UV-B-induced changes in wax composition were associated with increased wettability of tobacco leaf surfaces. Overall, the data are consistent with the view that UV-B radiation has a direct and fundamental effect on wax biosynthesis. Relationships between the physico-chemical nature of the leaf surface and sensitivity to UV-B radiation are discussed. (orig.)

Dispersion of Waxy Gas Oil by Some Nonionic Surfactants

International Nuclear Information System (INIS)

Khidr, T.T.; Mahmoud, S.A.

2004-01-01

Straight chain fatty alcohols having the following number of carbon atoms C 12 , C 14 , C 18 and C 21 each alcohol was ethoxylated to the same of ethylene oxide content, characterized through average molecular weight and elemental analysis. The surface properties of these compounds were studied through surface tension measurements. The synthesized additives were tested as flow improvers for improving the cold flow properties of two waxy gas oils through pour point test. The results show the right efficiency of these compounds in improving the flow ability. Comparative evaluation of the synthesized products with available commercial additive (com) showed their efficiency and suitability to use in gas oils. Wax modification was assisted through photo analysis. Correlation between wax modification and flow improvement in term of pour point depression appeared to be merely qualitative in such heterogeneous gas oil systems

Solvent Handbook Database System user's manual

International Nuclear Information System (INIS)

1993-03-01

Industrial solvents and cleaners are used in maintenance facilities to remove wax, grease, oil, carbon, machining fluids, solder fluxes, mold release, and various other contaminants from parts, and to prepare the surface of various metals. However, because of growing environmental and worker-safety concerns, government regulations have already excluded the use of some chemicals and have restricted the use of halogenated hydrocarbons because they affect the ozone layer and may cause cancer. The Solvent Handbook Database System lets you view information on solvents and cleaners, including test results on cleaning performance, air emissions, recycling and recovery, corrosion, and non-metals compatibility. Company and product safety information is also available

Diversity of cuticular wax among Salix species and Populus species hybrids.

Science.gov (United States)

Cameron, Kimberly D; Teece, Mark A; Bevilacqua, Eddie; Smart, Lawrence B

2002-08-01

The leaf cuticular waxes of three Salix species and two Populus species hybrids, selected for their ability to produce high amounts of biomass, were characterized. Samples were extracted in CH(2)Cl(2) three times over the growing season. Low kV SEM was utilized to observe differences in the ultrastructure of leaf surfaces from each clone. Homologous series of wax components were classified into organic groups, and the variation in wax components due to clone, sample time, and their interaction was identified. All Salix species and Populus species hybrids showed differences in total wax load at each sampling period, whereas the pattern of wax deposition over time differed only between the Salix species. A strong positive relationship was identified between the entire homologous series of alcohols and total wax load in all clones. Similarly strong relationships were observed between fatty acids and total wax load as well as fatty acids and alcohols in two Salix species and one Populus species hybrid. One Salix species, S. dasyclados, also displayed a strong positive relationship between alcohols and alkanes. These data indicate that species grown under the same environmental conditions produce measurably different cuticular waxes and that regulation of wax production appears to be different in each species. The important roles cuticular waxes play in drought tolerance, pest, and pathogen resistance, as well as the ease of wax extraction and analysis, strongly suggest that the characteristics of the cuticular wax may prove to be useful selectable traits in a breeding program.

Microencapsulation of flavors in carnauba wax.

Science.gov (United States)

Milanovic, Jelena; Manojlovic, Verica; Levic, Steva; Rajic, Nevenka; Nedovic, Viktor; Bugarski, Branko

2010-01-01

The subject of this study is the development of flavor wax formulations aimed for food and feed products. The melt dispersion technique was applied for the encapsulation of ethyl vanillin in wax microcapsules. The surface morphology of microparticles was investigated using scanning electron microscope (SEM), while the loading content was determined by HPLC measurements. This study shows that the decomposition process under heating proceeds in several steps: vanilla evaporation occurs at around 200 °C, while matrix degradation starts at 250 °C and progresses with maxima at around 360, 440 and 520 °C. The results indicate that carnauba wax is an attractive material for use as a matrix for encapsulation of flavours in order to improve their functionality and stability in products.

Microencapsulation of Flavors in Carnauba Wax

Directory of Open Access Journals (Sweden)

Branko Bugarski

2010-01-01

Full Text Available The subject of this study is the development of flavor wax formulations aimed for food and feed products. The melt dispersion technique was applied for the encapsulation of ethyl vanillin in wax microcapsules. The surface morphology of microparticles was investigated using scanning electron microscope (SEM, while the loading content was determined by HPLC measurements. This study shows that the decomposition process under heating proceeds in several steps: vanilla evaporation occurs at around 200 °C, while matrix degradation starts at 250 °C and progresses with maxima at around 360, 440 and 520 °C. The results indicate that carnauba wax is an attractive material for use as a matrix for encapsulation of flavours in order to improve their functionality and stability in products.

Solids precipitation in crude oils, gas-to-liquids and their blends

Science.gov (United States)

Ramanathan, Karthik

Gas-to-liquids (GTL) liquids are obtained from syngas by the Fischer-Tropsch synthesis. The blending of GTL liquids produced from natural gas/coal reserves and crude oils is a possibility in the near future for multiple reasons. Solids precipitation is a major problem in pipelines and refineries leading to significant additional operating costs. The effect of the addition of a paraffinic GTL liquid to crude oils on solids precipitation was investigated in this study. A Fourier transform infrared (FT-IR) spectroscopic technique was used to obtain solid-liquid equilibria (SLE) data for the various samples. The SLE of multiple systems of model oils composed of n-alkanes was investigated preliminarily. Blends of a model oil simulating a GTL liquid composition and a crude oil showed that the wax precipitation temperature (WPT) decreased upon blending. Three crude oils from different geographic regions (Alaskan North Slope, Colorado and Venezuela) and a laboratory-produced GTL liquid were used in the preparation of blends with five different concentrations of the GTL liquid. The wax precipitation temperatures of the blends were found to decrease with the increasing addition of the GTL liquid for all the oils. This effect was attributed to the solvent effect of the low molecular weight-paraffinic GTL liquid on the crude oils. The weight percent solid precipitated that was estimated as a function of temperature did not show a uniform trend for the set of crude oils. The asphaltene onset studies done on the blends with near-infrared spectroscopy indicated that the addition of GTL liquid could have a stabilizing effect on the asphaltenes in some oils. Analytical techniques such as distillation, solvent separation, HPLC, GC, and GPC were used to obtain detailed composition data on the samples. Two sets of compositional data with 49 and 86 pseudo-components were used to describe the three crude oils used in the blending work. The wax precipitation was calculated using a

Phototransformation of the herbicide sulcotrione on maize cuticular wax.

Science.gov (United States)

Ter Halle, Alexandra; Drncova, Daniela; Richard, Claire

2006-05-01

Vegetation plays a key role in environmental cycling and the fate of many organic pollutants. This is especially the case for pesticides because plant leaves are their first reaction environment after application. It is commonly accepted that photochemical reactions of pollutants on plants predominantly take place in the cuticular wax coating of the leaves. Thus, we used films made of either cuticular wax extracted from maize or carnauba gray wax as a model support. Under simulated sunlight irradiation, sulcotrione (a new class of triketone herbicides) sorbed on cuticular wax films was photolyzed and mainly underwent an intramolecular cyclization. The photoproduct is a chromone derivative which was isolated and fully characterized. It is reported for the first time as a sulcotrione degradation product. The photoreactivity of formulated sulcotrione at the surface of cuticular waxes was investigated too. It photodegraded more rapidly than nonformulated sulcotrione. This study also shows that the rate of sulcotrione photolysis was much faster than the rate of penetration into the wax; photolysis should be, thus, a relevant process in real conditions.

LD50 and repellent effects of essential oils from Argentinian wild plant species on Varroa destructor.

Science.gov (United States)

Ruffinengo, Sergio; Eguaras, Martin; Floris, Ignazio; Faverin, Claudia; Bailac, Pedro; Ponzi, Marta

2005-06-01

The repellent and acaricidal effects of some essential oils from the most typical wild plant species of northern Patagonia, Argentina, on Varroa destructor Anderson & Trueman were evaluated using a complete exposure test. Honey bees, Apis mellifera L., and mites (five specimens of each per dish) were introduced in petri dishes having different oil concentrations (from 0.1 to 25 micro per cage). Survival of bees and mites was registered after 24, 48, and 72 h. An attraction/repellence test was performed using a wax tube impregnated with essential oil and another tube containing wax only. The lowest LD50 values for mites were registered for Acantholippia seriphioides (A. Gray) Mold. (1.27 microl per cage) and Schinus molle L. (2.65 microl per cage) after 24 h, and for Wedelia glauca (Ortega) O. Hoffm. ex Hicken (0.59 microl per cage) and A. seriphioides (1.09 microl per cage) after 72 h of treatment. The oil with the highest selectivity ratio (A. mellifera LD50/V. destructor LD50) was the one extracted from S. molle (>16). Oils of Lippia junelliana (Mold.) Troncoso, Minthostachys mollis (HBK) Grieseb., and Lippia turbinata Grieseb. mixed with wax had repellent properties. None of the oils tested had attractive effects on Varroa mites.

Design of the GLARE tool. A grease lubrication apparatus for research and education

International Nuclear Information System (INIS)

Rawlings, B.

2012-01-01

The GLARE: Grease Lubrication Apparatus for Research and Education was designed as a fourth year thesis project with the University of Ontario Institute of Technology (UOIT). The purpose of the apparatus is to train Ontario Power Generation Nuclear (OPGN) staff to properly lubricate bearings with grease and to help detect early equipment failures. Proper re-lubrication is critical to the nuclear industry as equipment may be inaccessible for long periods of time. A secondary purpose for the tool is for UOIT research and undergraduate laboratories.This abstract provides an overview of the project and its application to the nuclear industry. (author)

Effects of a polymeric organic coagulant for industrial mineral oil ...

African Journals Online (AJOL)

The removal of chemical oxidation demand (COD), soap oil and grease (SOG), total suspended solids (TSS) and turbidity from the MOW were used as the response variables for the coagulation flotation process. This was done with a standard dissolved air flotation jar test. The results show that the actual COD, SOG, TSS ...

Controlled release of insect sex pheromones from paraffin wax and emulsions.

Science.gov (United States)

Atterholt, C A; Delwiche, M J; Rice, R E; Krochta, J M

1999-02-22

Paraffin wax and aqueous paraffin emulsions can be used as controlled release carriers for insect sex pheromones for mating disruption of orchard pests. Paraffin can be applied at ambient temperature as an aqueous emulsion, adheres to tree bark or foliage, releases pheromone for an extended period of time, and will slowly erode from bark and biodegrade in soil. Pheromone emulsions can be applied with simple spray equipment. Pheromone release-rates from paraffin were measured in laboratory flow-cell experiments. Pheromone was trapped from an air stream with an adsorbent, eluted periodically, and quantified by gas chromatography. Pheromone release from paraffin was partition-controlled, providing a constant (zero-order) release rate. A typical paraffin emulsion consisted of 30% paraffin, 4% pheromone, 4% soy oil, 1% vitamin E, 2% emulsifier, and the balance water. Soy oil and vitamin E acted as volatility suppressants. A constant release of oriental fruit moth pheromone from paraffin emulsions was observed in the laboratory for more than 100 days at 27 degreesC, with release-rates ranging from 0.4 to 2 mg/day, depending on the concentration and surface area of the dried emulsion. The use of paraffin emulsions is a viable method for direct application of insect pheromones for mating disruption. Sprayable formulations can be designed to release insect pheromones to the environment at a rate necessary for insect control by mating disruption. At temperatures below 38 degreesC, zero-order release was observed. At 38 degreesC and higher, pheromone oxidation occurred. A partition-controlled release mechanism was supported by a zero-order pheromone release-rate, low air/wax partition coefficients, and pheromone solubility in paraffin.

Preliminary evaluation of an aqueous wax emulsion for controlled-release coating.

Science.gov (United States)

Walia, P S; Stout, P J; Turton, R

1998-02-01

The purpose of this work was to evaluate the use of an aqueous carnauba wax emulsion (Primafresh HS, Johnson Wax) in a spray-coating process. This involved assessing the effectiveness of the wax in sustaining the release of the drug, theophylline. Second, the process by which the drug was released from the wax-coated pellets was modeled. Finally, a method to determine the optimum blend of pellets with different wax thicknesses, in order to yield a zero-order release profile of the drug, was addressed. Nonpareil pellets were loaded with theophylline using a novel powder coating technique. These drug-loaded pellets were then coated with different levels of carnauba wax in a 6-in. diameter Plexiglas fluid bed with a 3.5-in. diameter Wurster partition. Drug release was measured using a spin-filter dissolution device. The study resulted in continuous carnauba wax coatings which showed sustained drug release profile characteristics typical of a barrier-type, diffusion-controlled system. The effect of varying wax thickness on the release profiles was investigated. It was observed that very high wax loadings would be required to achieve long sustained-release times. The diffusion model, developed to predict the release of the drug, showed good agreement with the experimental data. However, the data exhibited an initial lag-time for drug release which could not be predicted a priori based on the wax coating thickness. A method of mixing pellets with different wax thicknesses was proposed as a way to approximate zero-order release.

Plant surface wax affects parasitoid's response to host footprints

Science.gov (United States)

Rostás, Michael; Ruf, Daniel; Zabka, Vanessa; Hildebrandt, Ulrich

2008-10-01

The plant surface is the substrate upon which herbivorous insects and natural enemies meet and thus represents the stage for interactions between the three trophic levels. Plant surfaces are covered by an epicuticular wax layer which is highly variable depending on species, cultivar or plant part. Differences in wax chemistry may modulate ecological interactions. We explored whether caterpillars of Spodoptera frugiperda, when walking over a plant surface, leave a chemical trail (kairomones) that can be detected by the parasitoid Cotesia marginiventris. Chemistry and micromorphology of cuticular waxes of two barley eceriferum wax mutants ( cer-za.126, cer-yp.949) and wild-type cv. Bonus (wt) were assessed. The plants were then used to investigate potential surface effects on the detectability of caterpillar kairomones. Here we provide evidence that C. marginiventris responds to chemical footprints of its host. Parasitoids were able to detect the kairomone on wild-type plants and on both cer mutants but the response to cer-yp.949 (reduced wax, high aldehyde fraction) was less pronounced. Experiments with caterpillar-treated wt and mutant leaves offered simultaneously, confirmed this observation: no difference in wasp response was found when wt was tested against cer-za.126 (reduced wax, wt-like chemical composition) but wt was significantly more attractive than cer-yp.949. This demonstrates for the first time that the wax layer can modulate the detectability of host kairomones.

Application of Fenton process to remove organic matter and PCBs from waste (fuller's earth) contaminated with insulating oil.

Science.gov (United States)

da Silva, Milady Renata Apolinário; Rodrigues, Eduardo de Oliveira; Espanhol-Soares, Melina; Silva, Flavio Soares; Kondo, Márcia Matiko; Gimenes, Rossano

2018-01-09

Polychlorinated biphenyls (PCBs) are carcinogenic to humans and can be found in fuller's earth used for the treatment of used transformer oil. This work describes an optimization of the Fenton process for the removal of contaminants from fuller's earth. The effects of pH (2.5 and 4.0), [H 2 O 2 ] (1.47 and 2.07 mol L -1 ), and [Fe 2+ ] (1.7 and 40 mmol L -1 ) were studied. The Fenton process efficiency was monitored using the decreases in the chemical oxygen demand (COD) and the concentrations of oil and grease, total carbon (TC), PCBs, and H 2 O 2 . The fuller's earth contaminated with insulating oil presented 35% (w/w) of TC, 34% (w/w) of oil and grease, 297.0 g L -1 COD, and 64 mg of PCBs per kg. The material could therefore be considered a dangerous waste. After Fenton treatment, using a slurry mode, there was a removal of 55% of COD, 20% of oil and grease, and 20% of TC, achieved at pH 2.5 using 2.07 mol L -1 of H 2 O 2 and 40.0 mmol L -1 of Fe 2+ . No PCBs were detected in the samples after the Fenton treatment, even using smaller amounts of Fenton reagents (1.47 mol L -1 of H 2 O 2 , 1.7 mmol L -1 of Fe 2+ , pH 2.5). The results indicated that the treated fuller's earth was free from PCB residues and could be disposed of in a simple landfill, in accordance with Brazilian PCB regulations.

Treatment of Oily Wastewater Produced From Old Processing Plant of North Oil Company

Directory of Open Access Journals (Sweden)

Dr. Faris Hammoodi Al-Ani

2012-03-01

Full Text Available The main objectives of this research were to study and analyses oily wastewater characteristics originating from old-processing plant of North Oil Company and to find a suitable and simple method to treat the waste so it can be disposed off safely. The work consists of two stages; the first was the study of oily wastewater characteristics and its negative impacts. The results indicated that oil and grease were the most dominant pollutant with concentration range between 1069 – 3269.3 mg/l that must be removed; other pollutants were found to be within Iraqi and EPA standards. The next stage was the use of these characteristics to choose the proper technology to treat that wastewater. This stage was divided into two stages: the first stage was a jar tests to find the optimum doses of alum, lime and powdered activated carbon (PAC. The second stage was the treatment by a batch pilot plant constructed for this purpose employing the optimum doses as determined from the first stage to treat the waste using a flotation unit followed by a filtration-adsorption unit. The removal efficiencies of flotation unit for oil and grease, COD, and T.S.S found to be 0.9789, 0.974, and 0.9933, respectively, while the removal efficiency for T.D.S was very low 0.0293. From filtration – adsorption column the removal efficiencies of oil and grease, T.D.S, COD, and T.S.S were found to be 0.9486, 0.8908, 0.6870, and 0.7815, respectively. The overall removal efficiencies of pilot plant were 0.9986, 0.8939, 0.9921, and 0.9950, respectively. The results indicated that this type of treatment was the simplest and most effective method that can be used to treat produced oily wastewater before disposal

Process for separating liquid hydrocarbons from waxes

Energy Technology Data Exchange (ETDEWEB)

Sowa, F J

1948-03-08

A process is described for the separation of liquid hydrocarbons from waxes comprising adding to a mixture of liquid hydrocarbons and waxes a sufficient quantity of an organo-silicon compound to cause the separation of the hydrocarbon and wax. The organo-silicon compounds are selected from the class of organic silicanes and their hydrolysis products and polymers. The silicanes have the formula R/sub y/SiX/sub z/, in which R is a saturated or unsaturated hydrocarbon radical, X is a halogen or another hydrocarbon radical or an -OR group, y has a value 1, 2, or 3 and z has a value 1, 2, or 3.

21 CFR 155.120 - Canned green beans and canned wax beans.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Canned green beans and canned wax beans. 155.120... Vegetables § 155.120 Canned green beans and canned wax beans. (a) Identity—(1) Definition. Canned green beans and canned wax beans are the foods prepared from succulent pods of fresh green bean or wax bean plants...

Effect of bacterial lipase on anaerobic co-digestion of slaughterhouse wastewater and grease in batch condition and continuous fixed-bed reactor.

Science.gov (United States)

Affes, Maha; Aloui, Fathi; Hadrich, Fatma; Loukil, Slim; Sayadi, Sami

2017-10-10

This study aimed to investigate the effects of bacterial lipase on biogas production of anaerobic co-digestion of slaughterhouse wastewater (SHWW) and hydrolyzed grease (HG). A neutrophilic Staphylococcus xylosus strain exhibiting lipolytic activity was used to perform microbial hydrolysis pretreatment of poultry slaughterhouse lipid rich waste. Optimum proportion of hydrolyzed grease was evaluated by determining biochemical methane potential. A high biogas production was observed in batch containing a mixture of slaughterhouse composed of 75% SHWW and 25% hydrolyzed grease leading to a biogas yield of 0.6 L/g COD introduced. Fixed bed reactor (FBR) results confirmed that the proportion of 25% of hydrolyzed grease gives the optimum condition for the digester performance. Biogas production was significantly high until an organic loading rate (OLR) of 2 g COD/L. d. This study indicates that the use of biological pre-treatment and FBR for the co-digestion of SHWW and hydrolyzed grease is feasible and effective.

Gluconeogenesis from storage wax in the cotyledons of jojoba seedlings.

Science.gov (United States)

Moreau, R A; Huang, A H

1977-08-01

The cotyledons of jojoba (Simmondsia chinensis) seeds contained 50 to 60% of their weight as intracellular wax esters. During germination there was a gradual decrease in the wax content with a concomitant rise in soluble carbohydrates, suggesting that the wax played the role of a food reserve. Thin layer chromatography revealed that both the fatty alcohol and fatty acid were metabolized. The disappearance of wax was matched with an increase of catalase, a marker enzyme of the gluconeogenic process in other fatty seedlings. Subcellular organelles were isolated by sucrose gradient centrifugation from the cotyledons at the peak stage of germination. The enzymes of the beta oxidation of fatty acid and of the glyoxylate cycle were localized in the glyoxysomes but not in the mitochondria. The glyoxysomes had specific activities of individual enzymes similar to those of the castor bean glyoxysomes. An active alkaline lipase was detected in the wax bodies at the peak stage of germination but not in the ungerminated seeds. No lipase was detected in glyoxysomes or mitochondria. After the wax in the wax bodies had been extracted with diethyl ether, the organelle membrane was isolated and it still retained the alkaline lipase. The gluconeogenesis from wax in the jojoba seedling appears to be similar, but with modification, to that from triglyceride in other fatty seedlings.

Study of the gelation behaviour of Brazilian waxy crude oils

Energy Technology Data Exchange (ETDEWEB)

Ziglio, C.M.; Sant' Ana, D.F. [Petroleo Brasileiro S.A., Petrobras, Rio de Janeiro (Brazil)

2008-07-01

The precipitation of wax from crude oil results in the formation of a paraffin network which evolves into a gel structure, causing a major operating issue for the petroleum industry. A gelled oil in a pipeline may need a very high re-start pressure that is beyond the capacity of the pump. The gelation of the oil can also develop into a wax deposit on the pipeline wall that restricts the flow of crude oil. Rheometry tests were used in this study to determine the yielding process of wax gels formed by the cooling of Brazilian crude oils. The effect of selected chemical additives on the gel strength was also examined. Dynamic rheology was used to study the oil-gel transition under quiescent conditions. Two rheological methods were used to study the gel yield stress, which is related to the gel strength. In the Creep and Recovery method, a stress was applied to the sample for a short period while the resulting deformation was measured. The stress was then removed to allow the sample to recover the gel structure. The steps of creep and recovery were repeated with an increasing stress value. The yield stress was identified as the minimum stress to cause an irreversible deformation in the sample. The yield stress of the gelled oil was estimated through dynamic measurements. Gel breakdown occurred when the sample was submitted to a critical strain, which is related to the yield stress value. This study showed that the gelation temperature can be reduced considerably by adding small amounts of readily available additives. These additives have an influence on yield stress values. In a cold re-start situation, they can reduce the pump pressure.

33 CFR 151.47 - Category D NLSs other than oil-like Category D NLSs that may be carried under this part.

Science.gov (United States)

2010-07-01

...-, primary) Animal and Fish oils, n.o.s. (see also Oil, edible) Animal and Fish acid oils and distillates, n..., n.o.s. (see also Oil, edible) Vegetable acid oils and distillates, n.o.s. Waxes: Candelilla Carnauba...

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Science.gov (United States)

2010-07-01

... coated or covered with dust, dirt, grime, grease, or another absorbent material. 761.375 Section 761.375... coated or covered with dust, dirt, grime, grease, or another absorbent material. (a) First wash. Cover..., absorbent pad until the surface appears dry. This cleaning should remove any residual dirt, dust, grime, or...

Microencapsulation of Flavors in Carnauba Wax

OpenAIRE

Milanovic, Jelena; Manojlovic, Verica; Levic, Steva; Rajic, Nevenka; Nedovic, Viktor; Bugarski, Branko

2010-01-01

The subject of this study is the development of flavor wax formulations aimed for food and feed products. The melt dispersion technique was applied for the encapsulation of ethyl vanillin in wax microcapsules. The surface morphology of microparticles was investigated using scanning electron microscope (SEM), while the loading content was determined by HPLC measurements. This study shows that the decomposition process under heating proceeds in several steps: vanilla evaporation occurs at aroun...

Research of Brazilian crude in pilot plant for base oil production; Pesquisa em planta piloto visando valorizar o cru nacional na producao de oleos lubrificantes

Energy Technology Data Exchange (ETDEWEB)

Fontes, Anita E.F.; Nogueira, Wlamir S.; Ximenes, Lelia M. de O. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES); Santos, Claudio A.P. dos [Fundacao Gorceix, Ouro Preto, MG (Brazil)

2004-07-01

One of the biggest challenges for PETROBRAS is to find alternative crude oils to produce base oil and wax in its refinery. Duque de Caxias refinery has been using imported crude oil for 31 years living with constants threats to continuity because of the Persian Gulf conflicts. If we analyze the profitability of this business, we can verify that the lubes complex had contributed for the profitability by about 41,9% in 2002, even using imported crude oil. So, if we can incorporate a national crude oil in the actual refinery scheme, we would produce besides strategic gains better profitability for the base oil and wax unit. This paper describes a series of tests performed in the pilot plant, in which we produced base oils and wax using a mixture of imported crude with Brazilian crude oil. The base oils produced were classified as Group I with lower aromatic, Sulphur and basic Nitrogen content. Another great advantage of this alternative is that the light fractions obtained from distillation step can be used as feed to make fuels of better quality, due to the lower sulphur content, thus also reducing the environmental impact. (author)

Preparation and characterization of carnauba wax nanostructured lipid carriers containing benzophenone-3.

Science.gov (United States)

Lacerda, S P; Cerize, N N P; Ré, M I

2011-08-01

Nanostructured lipid carriers (NLCs) are potential active delivery systems based on mixtures of solid lipids and liquid oil. In this paper, aqueous dispersions of NLCs were prepared by a hot high-pressure homogenization technique using carnauba wax as the solid lipid and isodecyl oleate as the liquid oil. The preparation and stability parameters of benzophenone-3-loaded NLCs have been investigated concerning particle size, zeta potential and loading capacity to encapsulate benzophenone-3, a molecular sunscreen. The current investigation illustrates the effect of the composition of the lipid mixture on the entrapment efficiency, in vitro release and stability of benzophenone-3-loaded in these NLCs. A loading capacity of approximately 5% of benzophenone-3 (m(BZ-3) /m(lipids) ) was characteristic of these systems. © 2011 The Authors. ICS © 2011 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Mineral and tar oils and paraffin and mineral waxes, extracting

Energy Technology Data Exchange (ETDEWEB)

1927-09-01

In the extraction of soluble bodies from coal and the like carbonaceous material, the coal is preheated in a closed vessel and then heated under pressure with the solvent. The pressure in either or both stages may be increased by gases or vapours more or less inert under the conditions, e.g. hydrogen, steam, carbon monoxide, and nitrogen. In an example, brown coal is maintained at 300/sup 0/C for 10 hours, thus producing a pressure of 100 atmospheres, and is then extracted for 10 hours at 300/sup 0/C and 100 atmospheres with benzene in a closed vessel. Over 60 per cent of the coal is dissolved. After separation of the undissolved coal and removal of the solvent the soluble products may be treated with either to extract resinous matter, and then with cyclohexane to extract wax-like matters. Alternatively the soluble products, alone or in solution or with the undissolved coal, may be destructively hydrogenated, or be cracked in presence of activated aluminium and hydrogen chloride.

Supercritical fluid chromatography of fish, shark and seal oils

DEFF Research Database (Denmark)

Borch-Jensen, Christina; Mollerup, Jørgen

1996-01-01

Various natural and treated fish, shark liver and seal oils have been analyzed by supercritical fluid chromatography (SFC) using a non-polar capillary column. The lipids are separated according to molecular mass. The lipid groups found included free fatty acids, cholesterol, squalene, vitamins, wax...... applications of SFC on fish, seal and shark liver oils are presented....

Geometric accuracy of wax bade models manufactured in silicon moulds

Directory of Open Access Journals (Sweden)

G. Budzik

2010-01-01

Full Text Available The article presents the test results of the geometric accuracy of wax blade models manufactured in silicon moulds in the Rapid Tooling process, with the application of the Vacuum Casting technology. In batch production casting waxes are designed for the manufacture of models and components of model sets through injection into a metal die. The objective of the tests was to determine the possibility of using traditional wax for the production of casting models in the rapid prototyping process. Blade models made of five types of casting wax were measured. The definition of the geometric accuracy of wax blade models makes it possible to introduce individual modifications aimed at improving their shape in order to increase the dimensional accuracy of blade models manufactured in the rapid prototyping process.

Phase Change Insulation for Energy Efficiency Based on Wax-Halloysite Composites

International Nuclear Information System (INIS)

Zhao, Yafei; Thapa, Suvhashis; Weiss, Leland; Lvov, Yuri

2014-01-01

Phase change materials (PCMs) have gained extensive attention in thermal energy storage. Wax can be used as a PCM in solar storage but it has low thermal conductivity. Introducing 10% halloysite admixed into wax yields a novel composite (wax-halloysite) which has a thermal conductivity of 0.5 W/mK. To increase the base conductivity, graphite and carbon nanotubes were added into the PCM composite improving its thermal energy storage. Thermal conductivity of wax-halloysite-graphite (45/45/10%) composite showed increased conductivity of 1.4 W/mK (3 times higher than the base wax-halloysite composite). Wax- halloysite-graphite-carbon nanotubes (45/45/5/5%) composite showed conductivity of 0.85 W/mK while maintaining the original shape perfectly until 91 °C (above the original wax melting point). Thermal conductivity can be further increased with higher doping of carbon nanotubes. This new composites are promising heat storage material due to good thermal stability, high thermal/electricity conductivity and ability to preserve its shape during phase transitions

Intensification of transferring the Kazakhstan high-congealed oil: challenges and advances

Energy Technology Data Exchange (ETDEWEB)

Maimakov, Tayhan P.; Boiko, Galinal; Lyubchenko, Nina P. [High education institute «UNAT», Almaty (Kazakhstan); Shaihutdinov, Yerengaip M. [Kazakh national technical university, Almaty (Kazakhstan)

2008-07-01

It were investigated the rheohgica! parameters of South-Turgay region crude oils at presence of novel pour point depressant additive DP-43/2005. It has shown that additive improves pour point and rheohgica; properties of crude oil mixture Kumkol-Akshabidak, inhibits wax deposition and can provide safe conditions of crude oil mixture transportation through pipeline at the cold season of year. Keywords: oil, temperature of fluidity loss, rheology, viscosity, oligomer depressor dopants.

Wear of Spur Gears Having a Dithering Motion and Lubricated with a Perfluorinated Polyether Grease

Science.gov (United States)

Krantz, Timothy; Oswald, Fred; Handschuh, Robert

2007-01-01

Gear contact surface wear is one of the important failure modes for gear systems. Dedicated experiments are required to enable precise evaluations of gear wear for a particular application. The application of interest for this study required evaluation of wear of gears lubricated with a grade 2 perfluorinated polyether grease and having a dithering (rotation reversal) motion. Experiments were conducted using spur gears made from AISI 9310 steel. Wear was measured using a profilometer at test intervals encompassing 10,000 to 80,000 cycles of dithering motion. The test load level was 1.1 GPa maximum Hertz contact stress at the pitch-line. The trend of total wear as a function of test cycles was linear, and the wear depth rate was approximately 1.2 nm maximum wear depth per gear dithering cycle. The observed wear rate was about 600 times greater than the wear rate for the same gears operated at high speed and lubricated with oil.

Absorption and distribution of orally administered jojoba wax in mice.

Science.gov (United States)

Yaron, A; Samoiloff, V; Benzioni, A

1982-03-01

The liquid wax obtained from the seeds of the arid-land shrub jojoba (Simmondsia chinensis) is finding increasing use in skin treatment preparations. The fate of this wax upon reaching the digestive tract was studied. 14C-Labeled wax was administered intragastrically to mice, and the distribution of the label in the body was determined as a function of time. Most of the wax was excreted, but a small amount was absorbed, as was indicated by the distribution of label in the internal organs and the epididymal fat. The label was incorporated into the body lipids and was found to diminish with time.

Radioisotope studies on the paradox in dispersion and agglomeration of sewage greases discharged from ocean outfalls

International Nuclear Information System (INIS)

Davison, A.; Easy, J.F.; Seatonberry, B.W.

1981-04-01

Experiments have been undertaken in the ocean off Sydney, Australia to monitor the movement and the dispersion of sewage solids. These solids were labelled with a radioisotope, gold-198 prior to ocean discharge. The labelled material was followed at sea using submersible scintillation detectors. Lateral and vertical dispersion coefficients were determined. The experiments showed that under some conditions the labelled sewage grease dispersed and under others the grease agglomerated. This variation is explained in terms of non-conservative processes

On the normal stress effect in grease-lubricated bearing seals

NARCIS (Netherlands)

Baart, P.; Lugt, Pieter Martin; Prakash, B.

2014-01-01

The film formation in lip seals, due to the non-Newtonian rheology of the lubricant, has been a topic of speculation. Earlier work suggests that normal stresses in grease would be favorable for the film buildup between the seal lip and shaft or bearing ring. In the current article, we evaluate this

ASPHALT-RESIN-WAX DEPOSITS ANALYSIS WITH PETROLEUM REFINERY EQUIPMENT USAGE

Directory of Open Access Journals (Sweden)

Nadejda Bondar

2013-12-01

Full Text Available The methodology and analysis of wax deposits formed in-water-cooling tower, cistern and tank from wax petroleum were developed. It was shown, that deposits consist of organic (>90% and inorganic components – the first one was enriched by high molecular wax hydrocarbons, the second one – by mechanical impurities. The methods of deposits utilization were proposed

Removal of oil from water by bentonite

International Nuclear Information System (INIS)

Moazed, H.; Viraraghavan, T.

1999-01-01

Many materials, included activated carbon, peat, coal, fiberglass, polypropylene, organoclay and bentonite have been used for removing oils and grease from water. However, bentonite has been used only rarely for this purpose. In this study Na-bentonite was used to remove oil from oil-in-water emulsions of various kinds such as standard mineral oil, cutting oils, refinery effluent and produced water from production wells at Estevan, Saskatchewan. Removal efficiencies obtained were 85 to 96 per cent for cutting oils, 84 to 86 per cent for produced water and 54 to 87 per cent for refinery effluent. Bentonite proved to be more effective in the removal of oil from oil-in-water emulsions than from actual waste waters; up to 96 percent from oil-in-water emulsions to only 87 per cent from actual waste water. The percentage of oil removed was found to be a function of the amount of bentonite added and the adsorption time up to the equilibrium time. Result also showed that the Langmuir, Freundlich and BET isotherms are well suited to describe the adsorption of oil by bentonite from the various oily waters employed in this study. 15 refs

Gluconeogenesis from Storage Wax in the Cotyledons of Jojoba Seedlings 1

Science.gov (United States)

Moreau, Robert A.; Huang, Anthony H. C.

1977-01-01

The cotyledons of jojoba (Simmondsia chinensis) seeds contained 50 to 60% of their weight as intracellular wax esters. During germination there was a gradual decrease in the wax content with a concomitant rise in soluble carbohydrates, suggesting that the wax played the role of a food reserve. Thin layer chromatography revealed that both the fatty alcohol and fatty acid were metabolized. The disappearance of wax was matched with an increase of catalase, a marker enzyme of the gluconeogenic process in other fatty seedlings. Subcellular organelles were isolated by sucrose gradient centrifugation from the cotyledons at the peak stage of germination. The enzymes of the β oxidation of fatty acid and of the glyoxylate cycle were localized in the glyoxysomes but not in the mitochondria. The glyoxysomes had specific activities of individual enzymes similar to those of the castor bean glyoxysomes. An active alkaline lipase was detected in the wax bodies at the peak stage of germination but not in the ungerminated seeds. No lipase was detected in glyoxysomes or mitochondria. After the wax in the wax bodies had been extracted with diethyl ether, the organelle membrane was isolated and it still retained the alkaline lipase. The gluconeogenesis from wax in the jojoba seedling appears to be similar, but with modification, to that from triglyceride in other fatty seedlings. Images PMID:16660087

Wax combs mediate nestmate recognition by guard honeybees

DEFF Research Database (Denmark)

D'Ettorre, Patrizia; Wenseleers, Tom; Dawson, Jenny

2006-01-01

Research has shown that the wax combs are important in the acquisition of colony odour in the honeybee, Apis mellifera. However, many of these studies were conducted in the laboratory or under artificial conditions. We investigated the role of the wax combs in nestmate recognition in the natural...

wax matrix tablets and its implication on dissolution prof

African Journals Online (AJOL)

acetaminophen-wax matrix tablet and hence its implication on dissolution profile. Acetaminophen-wax ... inertness, cost effectiveness, non- toxicity and more importantly their ... Liver Poole, England) at constant load (30 arbitrary units on the ...

A catalogue of crude oil and oil product properties, 1990

International Nuclear Information System (INIS)

Bobra, M.A.; Callaghan, S.

1990-09-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 109 refs

A catalogue of crude oil and oil product properties, 1992

International Nuclear Information System (INIS)

Whiticar, S.; Bobra, M.; Liuzzo, P.; Callaghan, S.; Fingas, M.; Jokuty, P.; Ackerman, F.; Cao, J.

1993-02-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 140 refs

Nest wax triggers worker reproduction in the bumblebee Bombus terrestris.

Science.gov (United States)

Rottler-Hoermann, Ann-Marie; Schulz, Stefan; Ayasse, Manfred

2016-01-01

Social insects are well known for their high level of cooperation. Workers of the primitively eusocial bumblebee Bombus terrestris are able to produce male offspring in the presence of a queen. Nonetheless, they only compete for reproduction, in the so-called competition phase, when the workforce is large enough to support the rearing of reproductives. So far, little is known about the proximate mechanisms underlying the shift between altruism and selfish behaviour in bumblebee workers. In this study, we have examined the influence of chemical cues from the nest wax on the onset of worker reproduction. Chemical analyses of wax extracts have revealed that the patterns and amounts of cuticular lipids change considerably during colony development. These changes in wax scent mirror worker abundance and the presence of fertile workers. In bioassays with queen-right worker groups, wax affects the dominance behaviour and ovarian development of workers. When exposed to wax from a colony in competition phase, workers start to compete for reproduction. We suggest that wax scent enables workers to time their reproduction by providing essential information concerning the social condition of the colony.

Characterization and chemical composition of epicuticular wax from banana leaves grown in Northern Thailand

Directory of Open Access Journals (Sweden)

Suporn Charumanee

2017-08-01

Full Text Available This study aimed to investigate the physicochemical properties and chemical composition of epicuticular wax extracted from leaves of Kluai Namwa, a banana cultivar which is widely grown in Northern Thailand. Its genotype was identified by a botanist. The wax was extracted using solvent extraction. The fatty acid profiles and physicochemical properties of the wax namely melting point, congealing point, crystal structures and polymorphism, hardness, color, and solubility were examined and compared to those of beeswax, carnauba wax and paraffin wax. The results showed that the genotype of Kluai Namwa was Musa acuminata X M. balbisiana (ABB group cv. Pisang Awak. The highest amount of wax extracted was 274 μg/cm2 surface area. The fatty acid composition and the physicochemical properties of the wax were similar to those of carnauba wax. It could be suggested that the banana wax could be used as a replacement for carnauba wax in various utilizing areas.

77 FR 462 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

Science.gov (United States)

2012-01-05

... sources--qualifying as cellulosic biofuel: [cir] Thermochemical pyrolysis. [cir] Thermochemical... covercrops, algal oil, biogenic waste oils/fats/greases, non-food grade corn oil, Canola/rapeseed oil, and... from annual covercrops, algal oil, biogenic waste oils/fats/greases, or non- food grade corn oil using...

Development of a Parafin Wax deposition Unit for Fused Deposition Modelling (FDM)

DEFF Research Database (Denmark)

D'Angelo, Greta; Hansen, Hans Nørgaard; Pedersen, David Bue

2014-01-01

. This project illustrates the redesign of an extrusion unit for the deposition of paraffin wax in Fused Deposition Modelling (FDM) instead of the conventional polymeric materials. Among the benefits and brought by the use of paraffin wax in such system are: the possibility to make highly complex and precise...... parts to subsequently use in a Lost Wax Casting process, multi-material Additive Manufacturing and the use of wax as support material during the production of complicated parts. Moreover it is believed that including waxes among the materials usable in FDM would promote new ways of using and exploring...

Oil and natural gas technology review-lubrication and lubricants

Energy Technology Data Exchange (ETDEWEB)

Moos, J

1966-01-01

A summary is presented of the advances made during 1967 in the following areas: production and transmission of natural gas; geosciences; drilling and production technology; secondary recovery; transportation by tanker, pipelines, and tank cars; storage; planning of refineries; control and automation; cracking and gasification of crude oil; separation and hydrogenation processes; petrochemicals; combustion technology; fuels and additives; air and water pollution control; production of lubricants; lubrication with mist, gas, and vapors; hydraulic fluids; lubricant additives; oxidation and aging of oils; greases; solid lubricants; bearings; machining; friction and wear; and changes in materials of construction. (220 refs.)

Oil content in seeds of the NPGS jojoba (Simmondsia chinensis) germplasm collection

Science.gov (United States)

Jojoba, Simmondsia chinensis, (Link) Schneider is a shrub native to warm and arid land regions of North and Latin America. Its seeds contain vegetable oil composed of long (C20-22), straight-chain liquid wax of non-glyceride esters. Minute amounts of triglycerides in its composition make the oil a l...

Effects of the concentration of emulsion of oil-in-water on the propagation velocity and attenuation

International Nuclear Information System (INIS)

Silva, L S F; Bibiano, D S; Figueiredo, M K K; Costa-Félix, R P B

2015-01-01

Soybean oil is an important feedstock for production of biodiesel that generates about 20 % of oily effluents. This paper studied the effect of concentration of soybean oil-inwater emulsions, in the range from 6 000 to 14 000 ppm, on the propagation velocity and ultrasonic attenuation. The Emission-Reception method has shown that the propagation velocity depends linearly on the concentration. The behavior of attenuation is similar to the velocity. Thus, both parameters can be used to measure oils and greases content in water

Investigation of liquid wax components of Egyptian jojoba seeds.

Science.gov (United States)

El-Mallah, Mohammed Hassan; El-Shami, Safinaz Mohammed

2009-01-01

Egyptian jojoba seeds newly cultivated in Ismailia desert in Egypt promoted us to determine its lipid components. Fatty alcohols, fatty acids, wax esters and sterols patterns were determined by capillary GLC whereas, tocopherols profile, isopropenoid alcohols and sterylglycosides were determined by HPLC. The Egyptian seeds are rich in wax esters (55 %) with fatty alcohols C20:1 and C22:1 as major components and amounted to 43.0 % and 45.6 % respectively followed by C24:1 and C18:1(9.6 % and 1.3 % respectively). The fatty acids profile showed that C20:1 is the major constituent (60 %) followed by C18:1 and C22:1 (14.5 and 11.8 % respectively) whereas C24:1 was present at low concentration amounted to 1.6 %. In addition, the Egyptian jojoba wax contained C18:2 fatty acid at a level of 8.7 %. Wax esters composition showed that the local wax had C42 and C40 esters as major components amounted to 51.1 and 30.1 % respectively. Also, it had C44 and C38 at reasonable amounts (10.0 and 6.3 % respectively). Whereas C36 and C46 were present at lower concentrations amounted to 1.4 and 1.1 respectively. The sterols analysis showed the presence of campe-, stigma-, beta-sito-, and isofuco- sterol amounting to 18.4 %, 6.9 %, 68.7 %, and 6.0 % respectively. The tocopherols pattern revealed that the local seed wax contained gamma-tocopherol as major constituent (79.2 %) followed by alpha-tocopherol (20.3 %). beta-tocopherol as well as delta-tocopherol were found as minor constituents. The isopropenoid alcohols and the sterylglycosides (free and acylated) were not detected. The wax is proposed to be used in oleo chemistry and cosmetics.

WAX ActiveLibrary: a tool to manage information overload.

Science.gov (United States)

Hanka, R; O'Brien, C; Heathfield, H; Buchan, I E

1999-11-01

WAX Active-Library (Cambridge Centre for Clinical Informatics) is a knowledge management system that seeks to support doctors' decision making through the provision of electronic books containing a wide range of clinical knowledge and locally based information. WAX has been piloted in several regions in the United Kingdom and formally evaluated in 17 GP surgeries based in Cambridgeshire. The evaluation has provided evidence that WAX Active-Library significantly improves GPs' access to relevant information sources and by increasing appropriate patient management and referrals this might also lead to an improvement in clinical outcomes.

Reproduction and subchronic feeding study of carnauba wax in rats.

Science.gov (United States)

Parent, R A; Re, T A; Babish, J G; Cox, G E; Voss, K A; Becci, P J

1983-02-01

The reproductive performance of Wistar rats fed carnauba wax at levels of 0.1, 0.3 or 1% in the diet and the effects of subchronic administration of carnauba wax at these dose levels on the resultant progeny were studied. Reproductive indices, body-weight gain, food consumption, haematological and clinical chemical data, ophthalmic, gross and histopathological examinations were used to study the possible toxic or pathological effects. Serum free fatty acid levels were found to be decreased in male and female rats fed carnauba wax at dietary levels of 0.3 and 1.0%. No other effects of feeding carnauba wax at levels up to 1.0% of the diet were observed.

Molecular and Evolutionary Mechanisms of Cuticular Wax for Plant Drought Tolerance

Directory of Open Access Journals (Sweden)

Dawei Xue

2017-04-01

Full Text Available Cuticular wax, the first protective layer of above ground tissues of many plant species, is a key evolutionary innovation in plants. Cuticular wax safeguards the evolution from certain green algae to flowering plants and the diversification of plant taxa during the eras of dry and adverse terrestrial living conditions and global climate changes. Cuticular wax plays significant roles in plant abiotic and biotic stress tolerance and has been implicated in defense mechanisms against excessive ultraviolet radiation, high temperature, bacterial and fungal pathogens, insects, high salinity, and low temperature. Drought, a major type of abiotic stress, poses huge threats to global food security and health of terrestrial ecosystem by limiting plant growth and crop productivity. The composition, biochemistry, structure, biosynthesis, and transport of plant cuticular wax have been reviewed extensively. However, the molecular and evolutionary mechanisms of cuticular wax in plants in response to drought stress are still lacking. In this review, we focus on potential mechanisms, from evolutionary, molecular, and physiological aspects, that control cuticular wax and its roles in plant drought tolerance. We also raise key research questions and propose important directions to be resolved in the future, leading to potential applications of cuticular wax for water use efficiency in agricultural and environmental sustainability.

Uncovered secret of a Vasseur-Tramond wax model.

Science.gov (United States)

Pastor, J F; Gutiérrez, B; Montes, J M; Ballestriero, R

2016-01-01

The technique of anatomical wax modelling reached its heyday in Italy during the 18th century, through a fruitful collaboration between sculptors and anatomists. It soon spread to other countries, and prestigious schools were created in England, France, Spain and Austria. Paris subsequently replaced Italy as the major centre of manufacture, and anatomical waxes were created there from the mid-19th century in workshops such as that of Vasseur-Tramond. This workshop began to sell waxes to European Faculties of Medicine and Schools of Surgery around 1880. Little is known of the technique employed in the creation of such artefacts as this was deemed a professional secret. To gain some insight into the methods of construction, we have studied a Vasseur-Tramond wax model in the Valladolid University Anatomy Museum, Spain, by means of multi-slice computerised tomography and X-ray analysis by means of environmental scanning electron microscopy. Scanning electron microscopy was used to examine the hair. These results have revealed some of the methods used to make these anatomical models and the materials employed. © 2015 Anatomical Society.

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tars, and oils containing powdered coal, coke, oreat, sulphur in suspension, by passing air or other oxygen-containing gas through a layer of the material of a depth sufficient substantially to deoxygenate the air and c., is carried out in stages in a series of treatment zones, the pressure in at least one of the zones being above atmospheric pressre. The products of oxidation include acetaldehyde, propionaldehyde, formic, acetic, propionic, butyric, acrylic and phthalic acids, alcohols, acetone, solvents, gums, and substances adapted for use as motor fuels or burnign oils. The oxidizing gas may be enriched with oxygen or be diluted with steam, and its point of entry into the oil and c. layer may be varied to promote or retard settlement of suspended solids.

Comparison the Marginal and Internal Fit of Metal Copings Cast from Wax Patterns Fabricated by CAD/CAM and Conventional Wax up Techniques

Science.gov (United States)

Vojdani, M; Torabi, K; Farjood, E; Khaledi, AAR

2013-01-01

Statement of Problem: Metal-ceramic crowns are most commonly used as the complete coverage restorations in clinical daily use. Disadvantages of conventional hand-made wax-patterns introduce some alternative ways by means of CAD/CAM technologies. Purpose: This study compares the marginal and internal fit of copings cast from CAD/CAM and conventional fabricated wax-patterns. Materials and Method: Twenty-four standardized brass dies were prepared and randomly divided into 2 groups according to the wax-patterns fabrication method (CAD/CAM technique and conventional method) (n=12). All the wax-patterns were fabricated in a standard fashion by means of contour, thickness and internal relief (M1-M12: representative of CAD/CAM group, C1-C12: representative of conventional group). CAD/CAM milling machine (Cori TEC 340i; imes-icore GmbH, Eiterfeld, Germany) was used to fabricate the CAD/CAM group wax-patterns. The copings cast from 24 wax-patterns were cemented to the corresponding dies. For all the coping-die assemblies cross-sectional technique was used to evaluate the marginal and internal fit at 15 points. The Student’s t- test was used for statistical analysis (α=0.05). Results: The overall mean (SD) for absolute marginal discrepancy (AMD) was 254.46 (25.10) um for CAD/CAM group and 88.08(10.67) um for conventional group (control). The overall mean of internal gap total (IGT) was 110.77(5.92) um for CAD/CAM group and 76.90 (10.17) um for conventional group. The Student’s t-test revealed significant differences between 2 groups. Marginal and internal gaps were found to be significantly higher at all measured areas in CAD/CAM group than conventional group (pmarginal and internal fit than CAD/CAM (machine-milled) technique. All the factors for 2 groups were standardized except wax pattern fabrication technique, therefore, only the conventional group results in copings with clinically acceptable margins of less than 120um. PMID:24724133

Effects of Atomic Oxygen and Grease on Outgassing and Adhesion of Silicone Elastomers for Space Applications

Science.gov (United States)

de Groh, Henry C.; Puleo, Bernadette J.; Steinetz, Bruce M.

An investigation of silicone elastomers for seals used in docking and habitat systems for future space exploration vehicles is being conducted at NASA. For certain missions, NASA is considering androgynous docking systems where two vehicles each having a seal would be required to: dock for a period of time, seal effectively, and then separate with minimum push-off forces for undocking. Silicone materials are generally chosen for their wide operating temperatures and low leakage rates. However silicone materials are often sticky and usually exhibit considerable adhesion when mated against metals and silicone surfaces. This paper investigates the adhesion unit pressure for a space rated silicone material (S0383-70) for either seal-on-seal (SoS) or seal-on-aluminum (SoAl) operation modes in the following conditions: as-received, after ground-based atomic-oxygen (AO) pre-treatment, after application of a thin coating of a space-qualified grease (Braycote 601EF), and after a combination of AO pre-treatment and grease coating. In order of descending adhesion reduction, the AO treatment reduced seal adhesion the most, followed by the AO plus grease pre-treatment, followed by the grease treatment. The effects of various treatments on silicone (S0383-70 and ELA-SA-401) outgassing properties were also investigated. The leading adhesion AO pre-treatment reduction led to a slight decrease in outgassing for the S0383-70 material and virtually no change in ELA-SA-401 outgassing.

Characterization of edible coatings consisting of pea starch, whey protein isolate, and Carnauba wax and their effects on oil rancidity and sensory properties of walnuts and pine nuts.

Science.gov (United States)

Mehyar, Ghadeer F; Al-Ismail, Khalid; Han, Jung H; Chee, Grace W

2012-02-01

Edible coatings made of whey protein isolate (WPI), pea starch (PS), and their combinations with carnauba wax (CW) were prepared and characterized. WPI combined with CW formed stable emulsion while PS with CW formed unstable emulsion and both formulations produced non-homogeneous films. Addition of PS to WPI: CW combination at the ratio of 1:1:1, respectively, resulted in stable emulsion and homogenous films. The emulsion PS: WPI: CW (1:1:2) was stable and formed a continuous film but had less homogenous droplets size distribution when compared to 1:1:1 film. Combined films had a reduced tensile strength and elongation compared to single component films. WPI : CW (1:1) films had higher elastic modulus than the WPI films, but the modulus reduced by the addition of PS. All the coating formulations were effective in preventing oxidative and hydrolytic rancidity of walnuts and pine nuts stored at 25 °C throughout the storage (12 d) but were less effective at 50 °C. Increasing the concentration of CW from 1:1:1 to 1:1:2 in PS: WPI: CW formulation did not contribute in further prevention of oil rancidity at 25 °C. Using of PS: WPI: CW (1:1:1) coating on both nuts significantly (P carnauba wax reduced the oxidative and hydrolytic rancidity of the nuts and improved sensory characteristics. © 2012 Institute of Food Technologists®

Accuracy of Digitally Fabricated Wax Denture Bases and Conventional Completed Complete Dentures

Directory of Open Access Journals (Sweden)

Bogna Stawarczyk

2017-12-01

Full Text Available The purpose of this investigation was to analyze the accuracy of digitally fabricated wax trial dentures and conventionally finalized complete dentures in comparison to a surface tessellation language (STL-dataset. A generated data set for the denture bases and the tooth sockets was used, converted into STL-format, and saved as reference. Five mandibular and 5 maxillary denture bases were milled from wax blanks and denture teeth were waxed into their tooth sockets. Each complete denture was checked on fit, waxed onto the dental cast, and digitized using an optical laboratory scanning device. The complete dentures were completed conventionally using the injection method, finished, and scanned. The resulting STL-datasets were exported into the three-dimensional (3D software GOM Inspect. Each of the 5 mandibular and 5 maxillary complete dentures was aligned with the STL- and the wax trial denture dataset. Alignment was performed based on a best-fit algorithm. A three-dimensional analysis of the spatial divergences in x-, y- and z-axes was performed by the 3D software and visualized in a color-coded illustration. The mean positive and negative deviations between the datasets were calculated automatically. In a direct comparison between maxillary wax trial dentures and complete dentures, complete dentures showed higher deviations from the STL-dataset than the wax trial dentures. The deviations occurred in the area of the teeth as well as in the distal area of the denture bases. In contrast, the highest deviations in both the mandibular wax trial dentures and the mandibular complete dentures were observed in the distal area. The complete dentures showed higher deviations on the occlusal surfaces of the teeth compared to the wax dentures. Computer-aided design/computer-aided manufacturing (CAD/CAM-fabricated wax dentures exhibited fewer deviations from the STL-reference than the complete dentures. The deviations were significantly greater in the

Epicuticular wax on cherry laurel (Prunus laurocerasus) leaves does not constitute the cuticular transpiration barrier.

Science.gov (United States)

Zeisler, Viktoria; Schreiber, Lukas

2016-01-01

Epicuticular wax of cherry laurel does not contribute to the formation of the cuticular transpiration barrier, which must be established by intracuticular wax. Barrier properties of cuticles are established by cuticular wax deposited on the outer surface of the cuticle (epicuticular wax) and in the cutin polymer (intracuticular wax). It is still an open question to what extent epi- and/or intracuticular waxes contribute to the formation of the transpiration barrier. Epicuticular wax was mechanically removed from the surfaces of isolated cuticles and intact leaf disks of cherry laurel (Prunus laurocerasus L.) by stripping with different polymers (collodion, cellulose acetate and gum arabic). Scanning electron microscopy showed that two consecutive treatments with all three polymers were sufficient to completely remove epicuticular wax since wax platelets disappeared and cuticle surfaces appeared smooth. Waxes in consecutive polymer strips and wax remaining in the cuticle after treatment with the polymers were determined by gas chromatography. This confirmed that two treatments of the polymers were sufficient for selectively removing epicuticular wax. Water permeability of isolated cuticles and cuticles covering intact leaf disks was measured using (3)H-labelled water before and after selectively removing epicuticular wax. Cellulose acetate and its solvent acetone led to a significant increase of cuticular permeability, indicating that the organic solvent acetone affected the cuticular transpiration barrier. However, permeability did not change after two subsequent treatments with collodion and gum arabic or after treatment with the corresponding solvents (diethyl ether:ethanol or water). Thus, in the case of P. laurocerasus the epicuticular wax does not significantly contribute to the formation of the cuticular transpiration barrier, which evidently must be established by the intracuticular wax.

Effects of peroxidized corn oil on performance, AMEn, and abdominal fat pad weight in broiler chicks

Science.gov (United States)

There is a trend to use more alternative lipids in poultry diets, either through animal-vegetable blends, distillers corn oil, or yellow grease. This has resulted in the use of lipids in poultry diets with a higher concentration of unsaturated fatty acids which have a greater potential for peroxidat...

Development and Performance Evaluation of Image-Based Robotic Waxing System for Detailing Automobiles.

Science.gov (United States)

Lin, Chi-Ying; Hsu, Bing-Cheng

2018-05-14

Waxing is an important aspect of automobile detailing, aimed at protecting the finish of the car and preventing rust. At present, this delicate work is conducted manually due to the need for iterative adjustments to achieve acceptable quality. This paper presents a robotic waxing system in which surface images are used to evaluate the quality of the finish. An RGB-D camera is used to build a point cloud that details the sheet metal components to enable path planning for a robot manipulator. The robot is equipped with a multi-axis force sensor to measure and control the forces involved in the application and buffing of wax. Images of sheet metal components that were waxed by experienced car detailers were analyzed using image processing algorithms. A Gaussian distribution function and its parameterized values were obtained from the images for use as a performance criterion in evaluating the quality of surfaces prepared by the robotic waxing system. Waxing force and dwell time were optimized using a mathematical model based on the image-based criterion used to measure waxing performance. Experimental results demonstrate the feasibility of the proposed robotic waxing system and image-based performance evaluation scheme.

Electrically conductive carbon nanofiber/paraffin wax composites for electric thermal storage

International Nuclear Information System (INIS)

Zhang Kun; Han Baoguo; Yu Xun

2012-01-01

Highlights: ► Carbon nanofiber (CNF)/paraffin wax composite is found to be a promising electric thermal storage material. ► The thermal storage capacity of CNF/paraffin wax composite is five times of traditional electric thermal storage material. ► CNF is shown to be an effective conductive filler for the composite. - Abstract: The research of electric thermal storage (ETS) has attracted a lot of attention recently, which converts off-peak electrical energy into thermal energy and release it later at peak hours. In this study, new electric thermal storage composites are developed by employing paraffin wax as thermal storage media and carbon nanofiber (CNF) as conductive fillers. Electric heating and thermal energy release performances of the CNF/paraffin wax composites are experimentally investigated. Experimental results show that, when the composites are heated to about 70 °C, the developed electrically conductive CNF/paraffin wax composites present a thermal storage capacity of about 280 kJ/kg, which is five times of that of traditional thermal storage medium such as ceramic bricks (54 kJ/kg). The CNF/paraffin wax composites can also effectively store the thermal energy and release the thermal energy in later hours.

Marginal adaptation of four inlay casting waxes on stone, titanium, and zirconia dies.

Science.gov (United States)

Michalakis, Konstantinos X; Kapsampeli, Vassiliki; Kitsou, Aikaterini; Kirmanidou, Yvone; Fotiou, Anna; Pissiotis, Argirios L; Calvani, Pasquale Lino; Hirayama, Hiroshi; Kudara, Yukio

2014-07-01

Different inlay casting waxes do not produce copings with satisfactory marginal accuracy when used on different die materials. The purpose of this study was to evaluate the marginal accuracy of 4 inlay casting waxes on stone dies and titanium and zirconia abutments and to correlate the findings with the degree of wetting between the die specimens and the inlay casting waxes. The inlay casting waxes tested were Starwax (Dentaurum), Unterziehwachs (Bredent), SU Esthetic wax (Schuler), and Sculpturing wax (Renfert). The marginal opening of the waxes was measured with a stereomicroscope on high-strength stone dies and on titanium and zirconia abutments. Photographic images were obtained, and the mean marginal opening for each specimen was calculated. A total of 1440 measurements were made. Wetting between die materials and waxes was determined after fabricating stone, titanium, and zirconia rectangular specimens. A calibrated pipette was used to place a drop of molten wax onto each specimen. The contact angle was calculated with software after an image of each specimen had been made with a digital camera. Collected data were subjected to a 2-way analysis of variance (α=.05). Any association between marginal accuracy and wetting of different materials was found by using the Pearson correlation. The wax factor had a statistically significant effect both on the marginal discrepancy (F=158.31, P<.001) and contact angle values (F=68.09, P<.001). A statistically significant effect of the die material factor both on the marginal adaptation (F=503.47, P<.001) and contact angle values (F=585.02, P<.001) was detected. A significant correlation between the marginal accuracy and the contact angle values (Pearson=0.881, P=.01) was also found. Stone dies provided wax copings with the best marginal integrity, followed by titanium and zirconia abutments. Unterziehwachs (Bredent), wax produced the best marginal adaptation on different die materials. A significant correlation was found

Oil and gas information 1995

International Nuclear Information System (INIS)

1996-07-01

This reference book on current developments in oil and gas supply and demand contains country-specific statistics for OECD countries on production, trade, demand and prices. This book is divided in four parts. Part 1 gives the statistics sources for oil, gas and by products (lubricants, bitumen, paraffin waxes etc..) supply, demand, consumption, origin, feedstocks, import and export prices, spot and end-user prices and taxes, and gives also the definitions of products, supply and consumption items reported in this book. Part 2 provides summary tables of world oil and gas market developments with time series back to the early 1970's. Parts 3 and 4 provide, in tables form, a more detailed and comprehensive picture of oil and gas supply and demand for the OECD by region and individual countries. (J.S.)

Tectonic microplates in a wax model of sea-floor spreading

International Nuclear Information System (INIS)

Katz, Richard F; Ragnarsson, Rolf; Bodenschatz, Eberhard

2005-01-01

Rotating, growing microplates are observed in a wax analogue model of sea-floor spreading. Wax microplates are kinematically similar to sea-floor tectonic microplates in terms of spreading rate and growth rate. Furthermore, their spiral pseudofault geometry is quantitatively consistent with Schouten's oceanic microplate model. These results suggest that Schouten's edge-driven microplate model captures the kinematics of tectonic microplate evolution on Earth. Based on the wax observations, a theory for the nucleation of overlapping spreading centres, the precursors of tectonic microplates, is developed

Properties of An Oral Nanoformulation of A Molecularly Dispersed Amphotericin B Comprising A Composite Matrix of Theobroma Oil and Bee’S Wax

Directory of Open Access Journals (Sweden)

Chloe See Wei Tan

2014-12-01

Full Text Available An amphotericin B-containing (AmB solid lipid nanoparticulate drug delivery system intended for oral administration, comprised of bee’s wax and theobroma oil as lipid components was formulated with the aim to ascertain the location of AmB within the lipid matrix: (a a homogenous matrix; (b a drug-enriched shell; or (c a drug enriched core. Both the drug-loaded and drug-free nanoparticles were spherical with AmB contributing to an increase in both the z-average diameter (169 ± 1 to 222 ± 2 nm and zeta potential (40.8 ± 0.9 to 50.3 ± 1.0 mV of the nanoparticles. A maximum encapsulation efficiency of 21.4% ± 3.0%, corresponding to 10.7 ± 0.4 mg encapsulated AmB within the lipid matrix was observed. Surface analysis and electron microscopic imaging indicated that AmB was dispersed uniformly within the lipid matrix (option (a above and, therefore, this is the most suitable of the three models with regard to modeling the propensity for uptake by epithelia and release of AmB in lymph.

Epicuticular wax on stomata of damaged silver fir trees (Abies alba Mili.

Directory of Open Access Journals (Sweden)

Tomislav Bačić

2011-01-01

Full Text Available Condition of epistomatal wax on the abaxial surface of the current and previous-year needles of damaged silver fir trees (Abies alba Mill., both from the polluted Risnjak and "clean" Donja Dobra sites in Gorski Kotar region, both influenced by pollutants coming from Europe, during two years, three times a year, were examined with Scanning Electron Microscope. In the course of time the wax tubules on the epistomatal rims of stomata in polluted, but also in "clean" needles surface, become fused and agglomerated rapidly to various extents of morphologically different types of amorphous wax crusts, primarily compact and particulate ones. This process begins very early, especially in polluted Risnjak site, and may be interpreted as a possible result of air pollution. However, the recrystalization, or production of new tubules, also appears relatively quickly in mostly cases. Quantitative estimations indicate a very large total amount of amorphous wax crusts in the current-year needles, and a very high percentage of the same wax in previous-year needles. Amorphous wax crusts cover stomatal pores, as well as the rims, disturbing the normal gas exchange. Statistically there is a signicant tendency of increase in wax degradation in the needles of the polluted site in comparison with those of the unpolluted one, but there is an insignificant wax degradation among the needles of damaged trees within each site. These results confirmed most of the research done in our preliminary report.

Biochemical response of sweet potato to bemul-wax coating ...

African Journals Online (AJOL)

Sweet potato (Ipomoea batatas Linn) tuber is a very nutritious but highly perishable crop that is subject to high wastages due to non-availability of appropriate storage techniques. This work assessed the effectiveness of treating the tubers with calcium chloride dip (CCD), bemul-wax (B-wax) and their combinations ...

Unheimlich. From Wax Figures to the Uncanny Valley

Directory of Open Access Journals (Sweden)

Pietro Conte

2012-01-01

Full Text Available In his pioneering History of Portraiture in Wax, Julius von Schlosser traced back the age-old history of a material which at that time seemed to be already antiquated, if not obsolete. Wax sculptures were rejected and ousted from art history because of their excessive similarity and adherence to models. One hundred years later, however, hyperrealism got its revenge with Maurizio Cattelan’s celebrated hanging children. Moving from that controversial artwork and focusing on the heated polemics over it, my paper will address the question of the well-known Unheimlichkeit of wax figures, investigated by Ernst Jentsch and Sigmund Freud in the early Twentieth Century and nowadays becoming increasingly topical thanks to the recent debate about the existence and nature of the so called Uncanny Valley.

Effects of cuticular wax on the postharvest quality of blueberry fruit.

Science.gov (United States)

Chu, Wenjing; Gao, Haiyan; Chen, Hangjun; Fang, Xiangjun; Zheng, Yonghua

2018-01-15

The blueberry fruit has a light-blue appearance because its blue-black skin is covered with a waxy bloom. This layer is easily damaged or removed during fruit harvesting and postharvest handling. We investigated the effects of wax removal on the postharvest quality of blueberry fruit and their possible mechanisms. The removal of natural wax on the fruit was found to accelerate the postharvest water loss and decay, reduce the sensory and nutritional qualities, and shorten the shelf-life. Wax removal decreased the activities of antioxidant enzymes and contents of antioxidants, and accelerated accumulation of ROS and lipid peroxidation, especially at the later period of storage. Moreover, the organellar membrane structure was disrupted in fruit with wax removed. These results indicate that cuticular wax plays an important role in maintaining the postharvest quality and delaying fruit senescence. The results should improve our understanding for better preservation of postharvest quality of blueberry fruit. Copyright © 2017 Elsevier Ltd. All rights reserved.

Composition and morphology of cuticular wax in blueberry (Vaccinium spp.) fruits.

Science.gov (United States)

Chu, Wenjing; Gao, Haiyan; Cao, Shifeng; Fang, Xiangjun; Chen, Hangjun; Xiao, Shangyue

2017-03-15

The chemical composition and morphology of cuticular wax in mature fruit of nine blueberry cultivars were investigated using gas chromatography-mass spectrometry (GC-MS) and scanning electron microscope (SEM). Triterpenoids and β-diketones were the most prominent compounds, accounting for on average 64.2% and 16.4% of the total wax, respectively. Ursolic or oleanolic acid was identified as the most abundant triterpenoids differing in cultivars. Two β-diketones, hentriacontan-10,12-dione and tritriacontan-12,14-dione, were detected in cuticular wax of blueberry fruits for the first time. Notably, hentriacontan-10,12-dione and tritriacontan-12,14-dione were only detected in highbush (V. corymbosum) and rabbiteye (V. ashei) blueberries, respectively. The results of SEM showed that a large amount of tubular wax deposited on the surface of blueberry fruits. There was no apparent difference in wax morphology among the nine cultivars. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of a plant leaf cuticle model wax, phase behaviour of model wax–water systems

International Nuclear Information System (INIS)

Fagerström, Anton; Kocherbitov, Vitaly; Westbye, Peter; Bergström, Karin; Mamontova, Varvara; Engblom, Johan

2013-01-01

Highlights: • Four individual crystalline phases were discovered in the model wax–water system. • Eutectic melting occurred in both dry and hydrated model wax. • The total transition enthalpy is smaller for the cuticle wax than for the model wax. • Water has a large plasticizing effect on cuticle wax. • The thermotropic transitions of model wax fit in the window of extracted leaf waxes. - Abstract: We investigated the thermotropic phase behaviour of plant leaf intracuticular wax and two representatives of its main components, 1-docosanol (C 22 H 45 OH) and dotriacontane (C 32 H 66 ), in dry and hydrated state. One objective was to obtain a model wax, which can be used to estimate formulations effects on cuticle diffusivity in vitro. The two wax components were chosen based on results from Gas Chromatography coupled to Mass Spectrometry analysis of cuticular wax. The wax was extracted from Clivia Miniata Regel leaves and contained 68% primary alcohols (C 16 –C 32 ) and 16% n-alkanes (C 21 –C 33 ). Differential Scanning Calorimetry, Polarized Light Microscopy and Small- and Wide Angle X-ray Diffraction were used to characterize the cuticular extract and the phase behaviour of the C 22 H 45 OH/C 32 H 66 /H 2 O model system. Four individual crystalline phases were discovered in the model wax–water system and eutectic melting occurred in both dry and hydrated state. The thermotropic transitions of the model wax occur within the broader transition region of the extracted leaf wax

On a new method to determine the yield stress in lubricating grease

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2015-01-01

An experimental study using both a controlled stress and a controlled strain rheometer has been undertaken to characterize lubricating grease in shear, creep, stress relaxation, and oscillatory flow, with a main focus on determining the yield stress. The yield stress was examined using a cone–plate

9 CFR 316.15 - Marking outside containers of inedible grease, etc.

Science.gov (United States)

2010-01-01

... grease, etc. 316.15 Section 316.15 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... letters not less than 2 inches high, while on tank cars and tank trucks the letters shall be not less than 4 inches high. (b) Inspected rendered animal fat which is intended not to be used for human food may...

Methods for separating boron from borated paraffin wax and its determination by ion chromatography

International Nuclear Information System (INIS)

Jeyakumar, S.

2015-01-01

Boron compounds are found to be useful in shielding against high-energy neutrons. In radiotherapy treatments, in order to protect occupational workers and patients from the undesirable neutron and gamma doses, paraffin wax containing B 4 C/boric acid is used. Low-level borate wastes generated from the nuclear power plants have been immobilized with paraffin wax using a concentrate waste drying system (CWDS). Borated paraffin waxes are prepared by mixing calculated amounts of either boric acid or boron carbide with the molten wax. This necessitates the determination of boron at different locations in order to check the homogeneous distribution of B over the borated wax. The determination of boron in nuclear materials is inevitable due to its high neutron absorption cross section. For the determination of boron in borated waxes, not many methods have been reported. A method based on the pyrohydrolysis extraction of boron and its quantification with ion chromatography was proposed for paraffin waxes borated with H 3 BO 3 and B 4 C. The B 4 C optimum pyrohydrolysis conditions were identified. Wax samples were mixed with U 3 O 8 , which prevents the sample from flare up, and also accelerates the extraction of boron. Pyrohydrolysis was carried out with moist O 2 at 950℃ for 60 and 90 min for wax with H 3 BO 3 and wax with B 4 C, respectively. Two simple methods of separation based on alkali extraction and melting wax in alkali were also developed exclusively for wax with H 3 BO 3 . In all the separations, the recovery of B was above 98%. During IC separation, B was separated as boron-mannitol anion complex. Linear calibration was obtained between 0.1 and 50 ppm of B, and LOD was calculated as 5 ppb (S/N=3). The reproducibility was better than 5% (RSD)

Problems in interpreting effects of air pollutants on spruce epicuticular waxes

International Nuclear Information System (INIS)

Bermadinger-Stabentheiner, E.

1994-01-01

Spruce needles are covered with rod-like crystals, which also fill the antechambers of the stomata with a dense meshwork. The scanning electron microscope (SEM) is very useful for studying epicuticular wax structure; with no intricate or laborious preparation, it is possible to obtain valuable information about the needle surface. Because the epicuticular wax layer forms a barrier between the plant and its environment, all influences that reach the surface from outside impact on this layer and, therefore, changes in epicuticular wax structure serve as diagnostic criteria for damage caused by air pollutants. This pollution influence begins as fusion of wax rods at the tips and results finally in total loss of the crystalline structure. Despite the simplicity of SEM investigations, alterations (artefacts) can occur to wax structures that may be confused with alterations caused by air pollutants (i.e., a too dense layer of twigs and needles, or careless handling with tweezers, results in mechanical damage that often influences the entire surface). Overheating occurring during transport or preparation and/or incorrect storage also produce artefacts. If the occurrence of such artefacts is taken into consideration, several contradictory interpretations of effects of air pollutants on epicuticular waxes can be explained. (orig.)

A robust sebum, oil, and particulate pollution model for assessing cleansing efficacy of human skin.

Science.gov (United States)

Peterson, G; Rapaka, S; Koski, N; Kearney, M; Ortblad, K; Tadlock, L

2017-06-01

With increasing concerns over the rise of atmospheric particulate pollution globally and its impact on systemic health and skin ageing, we have developed a pollution model to mimic particulate matter trapped in sebum and oils creating a robust (difficult to remove) surrogate for dirty, polluted skin. To evaluate the cleansing efficacy/protective effect of a sonic brush vs. manual cleansing against particulate pollution (trapped in grease/oil typical of human sebum). The pollution model (Sebollution; sebum pollution model; SPM) consists of atmospheric particulate matter/pollution combined with grease/oils typical of human sebum. Twenty subjects between the ages of 18-65 were enrolled in a single-centre, cleansing study comparisons between the sonic cleansing brush (normal speed) compared to manual cleansing. Equal amount of SPM was applied to the centre of each cheek (left and right). Method of cleansing (sonic vs. manual) was randomized to the side of the face (left or right) for each subject. Each side was cleansed for five-seconds using the sonic cleansing device with sensitive brush head or manually, using equal amounts of water and a gel cleanser. Photographs (VISIA-CR, Canfield Imaging, NJ, USA) were taken at baseline (before application of the SPM), after application of SPM (pre-cleansing), and following cleansing. Image analysis (ImageJ, NIH, Bethesda, MD, USA) was used to quantify colour intensity (amount of particulate pollutants on the skin) using a scale of 0 to 255 (0 = all black pixels; 255 = all white pixels). Differences between the baseline and post-cleansing values (pixels) are reported as the amount of SPM remaining following each method of cleansing. Using a robust cleansing protocol to assess removal of pollutants (SPM; atmospheric particulate matter trapped in grease/oil), the sonic brush removed significantly more SPM than manual cleansing (P pollution method easily allows assessment of efficacy through image analysis. © 2016 The Authors

Influence of Different Waxes on the Physical Properties of Linear ...

African Journals Online (AJOL)

NJD

2005-12-22

Dec 22, 2005 ... viscosity of a polymer melt. In many instances it ... amounts of different waxes on the viscosity (melt flow) of ..... Since the MFI is a direct measure of the viscosity .... melt flow index increasing with increasing wax content. There.

Wax Impaction in Nigerian School Children. | Eziyi | East and ...

African Journals Online (AJOL)

Background: Impacted wax has been classified as an ear disease. It can cause pain, itching, tinnitus hearing loss or otitis externa. The prevalence of cerumen impaction varies. The aim of this study was to determine the prevalence of impacted ear wax in primary school children and to determine, if there is any association ...

Wastewater transformations and fertilizer value when co-digesting differing ratios of swine manure and used cooking grease in low-cost digesters

Energy Technology Data Exchange (ETDEWEB)

Lansing, Stephanie [Department of Environmental Science and Technology, University of Maryland, 1445 Animal Sci./Ag. Eng. Bldg., College Park, MD 20742-2315 (United States); Martin, Jay F. [Department of Food, Agricultural, and Biological Engineering, The Ohio State University, 590 Woody Hayes Drive, Columbus, OH 43210-1057 (United States); Botero, Raul Botero; Nogueira da Silva, Tatiana; Dias da Silva, Ederson [EARTH University, Apartado Postal 4442 - 1000, San Jose (Costa Rica)

2010-12-15

A nine-month co-digestion investigation was conducted in Costa Rica to optimize animal wastewater treatment, renewable energy production, and fertilizer creation using 12 Taiwanese-model, plug-flow digesters (250 L each) constructed of tubular polyethylene and PVC piping, operating without mechanical or heating components. The experiment tested three replications of four treatment groups: the control (T0), which contained only swine manure, and T2.5, T5, and T10, which contained 2.5%, 5%, and 10% used cooking grease (by volume) combined with swine manure. T2.5 had the greatest methane production (45 L d{sup -1}), a 124% increase from the control. No adverse effects were observed from co-digesting 2.5% grease in terms of organic matter removal, pathogen reduction, grease removal, and pH. Chemical oxygen demand (COD) was reduced 94.7% to 1.96 g L{sup -1}, fecal coliforms and Escherichia coli were reduced 99.2 and 97.1%, respectively, and grease removal was 99.9%. The average effluent pH (7.05) and alkalinity in T2.5 was within the optimal range for methanogens and increased significantly during the nine-month experiment, likely due to adaptation of the methanogenic organisms to the influent grease concentrations. Total nitrogen concentration decreased 34.0%, and NH{sub 4}-N increased 97.1% during digestion in T2.5, with no significant differences between T2.5 and T0. There was less phosphorus reduction with co-digestion, with 181 mg g{sup -1} of total phosphorus (TP) in T2.5 and only 90.6 mg g{sup -1} of TP in T0, resulting in lower N:P ratios in the grease treatment groups due to the greater concentration of phosphorus in the effluent. (author)

Characterization of a plant leaf cuticle model wax, phase behaviour of model wax–water systems

Energy Technology Data Exchange (ETDEWEB)

Fagerström, Anton, E-mail: anton.fagerstrom@mah.se [Biomedical Science, Faculty of Health and Society, Malmö University, Malmö (Sweden); Kocherbitov, Vitaly [Biomedical Science, Faculty of Health and Society, Malmö University, Malmö (Sweden); Westbye, Peter; Bergström, Karin [Agro Applications Europe, AkzoNobel Surface Chemistry AB, Stenungsund (Sweden); Mamontova, Varvara [Ecological and Chemical Research, St. Petersburg Scientific Research Center for Ecological Safety, Russian Academy of Sciences, St. Petersburg (Russian Federation); Engblom, Johan [Biomedical Science, Faculty of Health and Society, Malmö University, Malmö (Sweden)

2013-11-10

Highlights: • Four individual crystalline phases were discovered in the model wax–water system. • Eutectic melting occurred in both dry and hydrated model wax. • The total transition enthalpy is smaller for the cuticle wax than for the model wax. • Water has a large plasticizing effect on cuticle wax. • The thermotropic transitions of model wax fit in the window of extracted leaf waxes. - Abstract: We investigated the thermotropic phase behaviour of plant leaf intracuticular wax and two representatives of its main components, 1-docosanol (C{sub 22}H{sub 45}OH) and dotriacontane (C{sub 32}H{sub 66}), in dry and hydrated state. One objective was to obtain a model wax, which can be used to estimate formulations effects on cuticle diffusivity in vitro. The two wax components were chosen based on results from Gas Chromatography coupled to Mass Spectrometry analysis of cuticular wax. The wax was extracted from Clivia Miniata Regel leaves and contained 68% primary alcohols (C{sub 16}–C{sub 32}) and 16% n-alkanes (C{sub 21}–C{sub 33}). Differential Scanning Calorimetry, Polarized Light Microscopy and Small- and Wide Angle X-ray Diffraction were used to characterize the cuticular extract and the phase behaviour of the C{sub 22}H{sub 45}OH/C{sub 32}H{sub 66}/H{sub 2}O model system. Four individual crystalline phases were discovered in the model wax–water system and eutectic melting occurred in both dry and hydrated state. The thermotropic transitions of the model wax occur within the broader transition region of the extracted leaf wax.

Anatomical models and wax Venuses: art masterpieces or scientific craft works?

Science.gov (United States)

Ballestriero, R

2010-02-01

The art of wax modelling has an ancient origin but rose to prominence in 14th century Italy with the cult of votive artefacts. With the advent of Neoclassicism this art, now deemed repulsive, continued to survive in a scientific environment, where it flourished in the study of normal and pathological anatomy, obstetrics, zoology and botany. The achievement of having originated the creation of anatomical models in coloured wax must be ascribed to a joint effort undertaken by the Sicilian wax modeller Gaetano Giulio Zumbo and the French surgeon Guillaume Desnoues in the late 17th century. Interest in anatomical wax models spread throughout Europe during the 18th century, first in Bologna with Ercole Lelli, Giovanni Manzolini and Anna Morandi, and then in Florence with Felice Fontana and Clemente Susini. In England, the art of anatomical ceroplastics was brought to London from Florence by the sculptor Joseph Towne. Throughout the centuries many anatomical artists preferred this material due to the remarkable mimetic likeness obtained, far surpassing any other material. Independent of the material used, whether wood, wax or clay, anatomical models were always considered merely craft works confined to hospitals or faculties of medicine and have survived to this day only because of their scientific interest. Italian and English waxes are stylistically different but the remarkable results obtained by Susini and Towne, and the fact that some contemporary artists are again representing anatomical wax bodies in their works, makes the border that formerly separated art and craft indistinguishable.

Sintering of wax for controlling release from pellets

OpenAIRE

Singh, Reena; Poddar, S. S.; Chivate, Amit

2007-01-01

The purpose of the present study was to investigate incorporation of hydrophobic (ie, waxy) material into pellets using a thermal sintering technique and to evaluate the pellets in vitro for controlled release. Pellets prepared by extrusion-spheronization technology were formulated with a water-soluble drug, microcrystalline cellulose, and carnauba wax. Powdered carnauba wax (4%–20%) prepared by grinding or by emulsification was studied with an attempt to retard the drug release. The inclusio...

Rice Bran Oil: A Versatile Source for Edible and Industrial Applications.

Science.gov (United States)

Pal, Yogita P; Pratap, Amit P

2017-01-01

Rice bran oil (RBO) is healthy gift generously given by nature to mankind. RBO is obtained from rice husk, a byproduct of rice milling industry and is gaining lot of importance as cooking oil due to presence of important micronutrient, gamma oryzanol. Its high smoke point is beneficial for its use for frying and deep frying of food stuff. It is popular because of balanced fatty acid profile (most ideal ratio of saturated, monounsaturated and polyunsaturated fatty acids), antioxidant capacity, and cholesterollowering abilities. Rice bran wax which is secondary by-product obtained as tank settling from RBO is used as a substitute for carnauba wax in cosmetics, confectionery, shoe creams etc. It can be also used as a source for fatty acid and fatty alcohol. The article is intended to highlight for the importance of RBO and its applications.

Estimation of modes frictions and greasing in bearing axial hanging of locomotives

Directory of Open Access Journals (Sweden)

V.N. Аstаkhоv

2012-04-01

Full Text Available Dependence is considered between the size of relative diametral gap and descriptions of work of the motor-axial bearing on the different rates of movement of diesel engine: by the type of the mode of greasing, thickness lubricating layer, by the coefficient of friction and intensity of wear.

Physico-chemical properties and efficacy of silk fibroin fabric coated with different waxes as wound dressing.

Science.gov (United States)

Kanokpanont, Sorada; Damrongsakkul, Siriporn; Ratanavaraporn, Juthamas; Aramwit, Pornanong

2013-04-01

Silk fibroin (SF) has been widely used as a wound dressing material due to its suitable physical and biological characteristics. In this study, a non-adhesive wound dressing which applies to cover the wound surface as an absorbent pad that would absorb wound fluid while accelerate wound healing was developed. The modification of SF fabrics by wax coating was purposed to prepare the non-adhesive wound dressing that is required in order to minimize pain and risk of repeated injury. SF woven fabrics were coated with different types of waxes including shellac wax, beeswax, or carnauba wax. Physical and mechanical properties of the wax-coated SF fabrics were characterized. It was clearly observed that all waxes could be successfully coated on the SF fabrics, possibly due to the hydrophobic interactions between hydrophobic domains of SF and waxes. The wax coating improved tensile modulus and percentage of elongation of the SF fabrics due to the denser structure and the thicker fibers coated. The in vitro degradation study demonstrated that all wax-coated SF fabrics remained up to 90% of their original weights after 7 weeks of incubation in lysozyme solution under physiological conditions. The wax coating did not affect the degradation behavior of the SF fabrics. A peel test of the wax-coated SF fabrics was carried out in the partial- and full-thickness wounds of porcine skin in comparison to that of the commercial wound dressing. Any wax-coated SF fabrics were less adhesive than the control, as confirmed by less number of cells attached and less adhesive force. This might be that the wax-coated SF fabrics showed the hydrophobic property, allowing the loosely adherence to the hydrophilic wound surface. In addition, the in vivo biocompatibility test of the wax-coated SF fabrics was performed in Sprague-Dawley rats with subcutaneous model. The irritation scores indicated that the carnauba wax-coated SF fabric was not irritant while the shellac wax or beeswax-coated SF

Cotton for removal of aquatic oil spills

International Nuclear Information System (INIS)

Parker, H.W.; Fedler, C.B.; Heintz, C.E.; Nash, P.T.; Carr, D.L.; Lu, M.

1992-01-01

Raw cotton has considerable potential for selective removal of spilled oil and oil products from surface waters, since the natural waxes on the raw cotton make it preferentially oil wet. This potential was recognized in the early seventies at Texas Tech University. More recently other research workers have considered cotton as an adsorbent for spilled oil. The adsorbent market is now dominated by synthetic materials, such as air-blown polypropylene fiber, inorganic clays, and recycled paper and paper products. This paper further examines the potential of cotton in relation to these other adsorbents. Emphasis is placed on the potential for complete biodegradation of oil-soaked cotton adsorbents as a means avoiding the expense for incineration and/or the long-term environmental risk associated with placing the used adsorbents in landfills

Biological, medicinal and toxicological significance of Eucalyptus leaf essential oil: a review.

Science.gov (United States)

Dhakad, Ashok K; Pandey, Vijay V; Beg, Sobia; Rawat, Janhvi M; Singh, Avtar

2018-02-01

The genus Eucalyptus L'Heritier comprises about 900 species, of which more than 300 species contain volatile essential oil in their leaves. About 20 species, within these, have a high content of 1,8-cineole (more than 70%), commercially used for the production of essential oils in the pharmaceutical and cosmetic industries. However, Eucalyptus is extensively planted for pulp, plywood and solid wood production, but its leaf aromatic oil has astounding widespread biological activities, including antimicrobial, antiseptic, antioxidant, chemotherapeutic, respiratory and gastrointestinal disorder treatment, wound healing, and insecticidal/insect repellent, herbicidal, acaricidal, nematicidal, and perfumes, soap making and grease remover. In the present review, we have made an attempt to congregate the biological ingredients of leaf essential oil, leaf oil as a natural medicine, and pharmacological and toxicological values of the leaf oil of different Eucalyptus species worldwide. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

QUALITATIVE ANALYSIS METHOD OF DETECTION OF WAX CONTENT IN GORENGAN USING SMARTPHONE

Directory of Open Access Journals (Sweden)

Yulia Yulia

2018-05-01

Full Text Available Wax is one of the compounds that can be misused to be added to Gorengan, Indonesian fritter, to keep them crispy. Gorengan containing wax is difficult to identify visually, so a quick and easy method of detecting wax content is required. The purpose of this research is to develop and evaluate the analytical performance of detecting wax content in gorengan using smartphone. Gorengan sample was dissolved with hexane and then added reagent that will give discoloration followed by analysis using smartphone. Some analysis performance parameters were evaluated in terms of linearity and detection limit, qualitative analysis capability, precision, and selectivity test. The developed method was also applied in some gorengan samples. The result shows that the detection of wax content in gorengan can be conducted by using reagent consisting of NaOH, Schift, and curcumin (1 : 2 : 2. Performance analysis shows that the linearity measurement at concentration between 10% and 25% has correlation coefficient (r of 0.9537 with detection limit at concentration of 2% and precision (%RSD less than 3%. The developed method can be applied for the detection of wax content in gorengan in the market.

Twenty Years after the Nakhodka Oil Spill Accident in the Sea of Japan, How Has Contamination Changed?

Directory of Open Access Journals (Sweden)

Kazue Tazaki

2018-04-01

Full Text Available The Nakhodka, a Russian tanker loaded with 19,000 kL of C-type heavy oil, was broken up into sections and submerged off Oki Island, Shimane Prefecture, Japan on 2 January 1997. The bow, after drifting for four days, was wrecked off Anto, Sakai City (Mikuni, Fukui Prefecture, threatening the environment throughout the various shores of Ishikawa Prefecture. The accident, caused by a heavy oil spill of 6200 kL, created serious environmental problems along the shores of Hokuriku District. We report the characterization of C-type heavy oil 20 years after the accident at the Atake seashore, Wajima City, Ishikawa Prefecture, in the Sea of Japan, based on observations in the field on 18 January 2017. We studied the microstructure, mineralogy, chemical composition, and radioactivity associated with microorganisms in the soils, and buried fishing nets and ropes that were contaminated with C-type heavy oil from this spill. The analyses used a combination of micro techniques, analytical data based on a CHN analyzer, X-ray powder diffraction (XRD, and two kinds of scanning electron microscopy equipped with energy dispersive spectroscopy (SEM-EDS. Hydrocarbon-degrading bacteria, paraffin wax, cristobalite, graphite, calcite, halite, and biotite from the Nakhodka oil spill were recognized on the surface of ropes and in the soil of the polluted seashores after 20 years. The chemical compositions indicated that high concentrations of C, O, Na, Al, Si, P, S, Ca, Fe, Cl, Sr, and Pb were predominantly indigenous to the Nakhodka oil spill. In the XRD analysis of the oil-contaminated soils on the rope at the Atake seashore indicated paraffin wax, graphite, sulfate, calcite and halite refractions with clay minerals, after 20 years. To date, no report has described the results of electron microscopy observations, such as Micrococcus bacillus and filamentous fungi, found in oil-contaminated soils after 20 years. In this research, such observations are introduced as �

Vertical pump turbine oil environmental evaluation

Energy Technology Data Exchange (ETDEWEB)

Culver, G.

1991-04-01

In Oregon low-temperature geothermal injection well construction, siting and receiving formations requires approval by the Water Resources Department (OWRD). In addition, the Oregon Department of Environmental Quality (ODEQ) has regulations concerning injection. Conversations with the OWRD and ODEQ representatives indicated they were very concerned about the potential for contamination of the geothermal (and cooler but hydraulically connected) aquifers by oils and grease. Their primary concern was over the practice of putting paraffin, motor oils and other hydrocarbons in downhole heat exchanger (DHE) wells to prevent corrosion. They also expressed considerable concern about the use of oil in production well pumps since the fluids pumped would be injected. Oregon (and Idaho) prohibit the use of oil-lubricated pumps for public water supplies except in certain situations where non-toxic food-grade lubricants are used. Since enclosed-lineshaft oil-lubricated pumps are the mainstay of direct-use pumping equipment, the potential for restricting their use became a concern to the Geo-Heat Center staff. An investigation into alternative pump lubrication schemes and development of rebuttals to potential restrictions was proposed and approved as a contract task. (SM)

The MIEL1 E3 Ubiquitin Ligase Negatively Regulates Cuticular Wax Biosynthesis in Arabidopsis Stems.

Science.gov (United States)

Lee, Hong Gil; Kim, Juyoung; Suh, Mi Chung; Seo, Pil Joon

2017-07-01

Cuticular wax is an important hydrophobic layer that covers the plant aerial surface. Cuticular wax biosynthesis is shaped by multiple layers of regulation. In particular, a pair of R2R3-type MYB transcription factors, MYB96 and MYB30, are known to be the main participants in cuticular wax accumulation. Here, we report that the MYB30-INTERACTING E3 LIGASE 1 (MIEL1) E3 ubiquitin ligase controls the protein stability of the two MYB transcription factors and thereby wax biosynthesis in Arabidopsis. MIEL1-deficient miel1 mutants exhibit increased wax accumulation in stems, with up-regulation of wax biosynthetic genes targeted by MYB96 and MYB30. Genetic analysis reveals that wax accumulation of the miel1 mutant is compromised by myb96 or myb30 mutation, but MYB96 is mainly epistatic to MIEL1, playing a predominant role in cuticular wax deposition. These observations indicate that the MIEL1-MYB96 module is important for balanced cuticular wax biosynthesis in developing inflorescence stems. © The Author 2017. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Inverse gradients in leaf wax δD and δ13C values along grass blades of Miscanthus sinensis: implications for leaf wax reproduction and plant physiology.

Science.gov (United States)

Gao, Li; Huang, Yongsong

2013-06-01

Compound specific hydrogen and carbon isotopic ratios of higher plant leaf waxes have been extensively used in paleoclimate and paleoenvironmental reconstructions. However, studies so far have focused on the comparison of leaf wax isotopic differences in bulk leaf samples between different plant species. We sampled three different varieties of tall grasses (Miscanthus sinensis) in six segments from base to tip and determined hydrogen and carbon isotopic ratios of leaf waxes, as well as hydrogen and oxygen isotopic ratios of leaf water samples. We found an increasing, base-to-tip hydrogen isotopic gradient along the grass blades that can probably be attributed to active leaf wax regeneration over the growth season. Carbon isotopic ratios, on the other hand, show opposite trends to hydrogen isotopic ratios along the grass blades, which may reflect different photosynthetic efficiencies at different blade locales.

SEPARATION OF FISCHER-TROPSCH WAX PRODUCTS FROM ULTRAFINE IRON CATALYST PARTICLES

Energy Technology Data Exchange (ETDEWEB)

James K. Neathery; Gary Jacobs; Burtron H. Davis

2004-03-31

In this reporting period, a fundamental filtration study was started to investigate the separation of Fischer-Tropsch Synthesis (FTS) liquids from iron-based catalyst particles. Slurry-phase FTS in slurry bubble column reactor systems is the preferred mode of production since the reaction is highly exothermic. Consequently, heavy wax products must be separated from catalyst particles before being removed from the reactor system. Achieving an efficient wax product separation from iron-based catalysts is one of the most challenging technical problems associated with slurry-phase FTS. The separation problem is further compounded by catalyst particle attrition and the formation of ultra-fine iron carbide and/or carbon particles. Existing pilot-scale equipment was modified to include a filtration test apparatus. After undergoing an extensive plant shakedown period, filtration tests with cross-flow filter modules using simulant FTS wax slurry were conducted. The focus of these early tests was to find adequate mixtures of polyethylene wax to simulate FTS wax. Catalyst particle size analysis techniques were also developed. Initial analyses of the slurry and filter permeate particles will be used by the research team to design improved filter media and cleaning strategies.

Effect of bacterial lipase on anaerobic co-digestion of slaughterhouse wastewater and grease in batch condition and continuous fixed-bed reactor

OpenAIRE

Affes, Maha; Aloui, Fathi; Hadrich, Fatma; Loukil, Slim; Sayadi, Sami

2017-01-01

Background This study aimed to investigate the effects of bacterial lipase on biogas production of anaerobic co-digestion of slaughterhouse wastewater (SHWW) and hydrolyzed grease (HG). A neutrophilic Staphylococcus xylosus strain exhibiting lipolytic activity was used to perform microbial hydrolysis pretreatment of poultry slaughterhouse lipid rich waste. Results Optimum proportion of hydrolyzed grease was evaluated by determining biochemical methane potential. A high biogas production was o...

Laboratory Deposition Apparatus to Study the Effects of Wax Deposition on Pipe Magnetic Field Leakage Signals

Directory of Open Access Journals (Sweden)

Karim Mohd Fauzi Abd

2014-07-01

Full Text Available Accurate technique for wax deposition detection and severity measurement on cold pipe wall is important for pipeline cleaning program. Usually these techniques are validated by conventional techniques on laboratory scale wax deposition flow loop. However conventional techniques inherent limitations and it is difficult to reproduce a predetermine wax deposit profile and hardness at designated location in flow loop. An alternative wax deposition system which integrates modified pour casting method and cold finger method is presented. This system is suitable to reproduce high volume of medium hard wax deposit in pipe with better control of wax deposit profile and hardness.

Effect of waste wax and chain structure on the mechanical and physical properties of polyethylene

Directory of Open Access Journals (Sweden)

M.A. AlMaadeed

2015-05-01

The wax dispersion in the matrix strongly depends on the percentage of wax added to the polymer and the molecular structure of the polymer. It was found that increasing the wax content enhances the phase separation. LDPE undergoes less phase separation due to its highly branched structure composed of a network of short and long chain branches. The wax has no pronounced plasticising effect on the polymer. This is clearly manifested in LDPE as no change in the melting temperature occurred. LLDPE and HDPE were slightly affected by a high concentration of wax (30% and 40%. This is due to the non-uniform distribution of short chain branching along the LLDPE and HDPE main chains, which can interact with the wax structure.

Subchronic feeding study of carnauba wax in beagle dogs.

Science.gov (United States)

Parent, R A; Cox, G E; Babish, J G; Gallo, M A; Hess, F G; Becci, P J

1983-02-01

Carnauba wax fed at levels of 0.1, 0.3 and 1% in the diet to beagle dogs for 28 wk did not produce evidence of toxicity or pathological effects. Body weight gain, food consumption, clinical chemical, haematological, and urine analysis data, and organ weights of animals fed carnauba wax were comparable with those of control animals. Ophthalmic, gross and histopathological examinations revealed no significant treatment-related findings.

Stable hydrogen isotopic composition of n-alkanes in atmospheric aerosols as a tracer for the source region of terrestrial plant waxes

Science.gov (United States)

Yamamoto, S.; Kawamura, K.

2009-12-01

Studies on molecular composition and compound-specific carbon isotopic ratio (δ13C) of leaf wax n-alkanes in atmospheric aerosols have revealed a long-range atmospheric transport of terrestrial higher plant materials over the south Atlantic and western Pacific oceans. However, molecular and δ13C compositions of terrestrial plant waxes in the eastern part of the Asian continent are relatively constant reflecting C3-dominated vegetation, which makes it difficult to specify the source regions of plant materials in the atmospheric aerosols over the East Asia and northwest Pacific regions. Recent observation displays a large (>100‰) spatial variation in hydrogen isotopic composition (δD) of rainwater in East Asia. Because δD values of terrestrial higher plants sensitively reflect those of precipitation waters, δD of leaf waxes are expected to provide information on their source region. In this study, we measured the δD of n-alkanes in atmospheric aerosols from Tokyo to better understand the origin of leaf wax n-alkanes in atmospheric aerosols. The δD values of fossil fuel n-alkanes (C21 to C24) in Tokyo aerosols range from -65 to -94‰, which are in a range of those reported in marine crude oils. In contrast, the δD of higher molecular weight (C29 and C31) n-alkanes (δDHMW) show much larger values by ~70‰ than those of fossil fuel n-alkanes. Their values were found to exhibit concomitant variations with carbon preference index (CPI), suggesting that the δDHMW reflect the δD of leaf wax n-alkanes with a variable contribution from fossil fuel n-alkanes. Nevertheless, good positive correlation (r = 0.89, p < 0.01) between the δDHMW and CPI values enable us to remove the contribution of fossil fuels using a mass balance approach by assuming that CPI of fossil fuel is 1 and CPI of plant waxes is 5-15. Calculated n-alkane δD values averaged from -170 to -185‰ for C29 and from -155 to -168‰ for C31. These values are consistent with those reported from

Biodegradation of polyurethane derived from castor oil

Directory of Open Access Journals (Sweden)

José M. Cangemi

2008-09-01

Full Text Available The aim of this research was to study the biodegradation of a polymer derived from castor oil, which is a renewable, natural material that is a practical alternative for the replacement of traditional polyurethane foams. Due to its molecular structure, which contains polyester segments derived from vegetable oil, the polymeric surface is susceptible to microorganism attack. This study tested the biological degrading agent that was in contact with the microorganisms resulting from microbiological grease degrading agents, when foam was inoculated. Solid-media agar-plate tests were conducted for their potential to evaluate the biodegradation of polymeric particles by specific strains of microorganisms during 216 hours. The growth rate was defined. This technique provides a way of distinguishing the degradation abilities of microorganisms from the degradability of materials.

Electrochemical behaviors of wax-coated Li powder/Li 4Ti 5O 12 cells

Science.gov (United States)

Park, Han Eol; Seong, Il Won; Yoon, Woo Young

The wax-coated Li powder specimen was effectively synthesized using the drop emulsion technique (DET). The wax layer on the powder was verified by SEM, Focused Ion Beam (FIB), EDX and XPS. The porosity of a sintered wax-coated Li electrode was measured by linear sweep voltammetry (LSV) and compared with that of a bare, i.e., un-coated Li electrode. The electrochemical behavior of the wax-coated Li powder anode cell was examined by the impedance analysis and cyclic testing methods. The cyclic behavior of the wax-coated Li powder anode with the Li 4Ti 5O 12 (LTO) cathode cell was examined at a constant current density of 0.35 mA cm -2 with the cut-off voltages of 1.2-2.0 V at 25 °C. Over 90% of the initial capacity of the cell remained even after the 300th cycle. The wax-coated Li powder was confirmed to be a stable anode material.

Crystallography of waxes - an electron diffraction study of refined and natural products

Science.gov (United States)

Dorset, Douglas L.

1997-02-01

The crystal structure of four waxes has been investigated by electron crystallography. Two of these waxes, including a refined petroleum product (Gulfwax) and a material from lignite (montan wax), form well ordered crystals and their structure could be solved quantitatively from the observed 0022-3727/30/3/018/img1 diffraction patterns. As also found previously for simpler binary n-paraffin solid solutions, the average structure resembles that of a pure paraffin (e.g. n-0022-3727/30/3/018/img2) but with a Gaussian distribution of atomic occupancies near the chain ends to account for the statistical distribution of chain lengths within a lamella. Two other waxes from living organisms, South African bee honeycomb and the leaves of the Brazilian carnauba palm, are much less ordered, even though they share the same methylene subcell packing of the most crystalline parts of the previous materials. It appears that these waxes cannot fully separate into distinct lamellae, perhaps due to the presence of very long `tie' molecules, and are therefore `frustrated' crystal structures.

Wax Precipitation Modeled with Many Mixed Solid Phases

DEFF Research Database (Denmark)

Heidemann, Robert A.; Madsen, Jesper; Stenby, Erling Halfdan

2005-01-01

The behavior of the Coutinho UNIQUAC model for solid wax phases has been examined. The model can produce as many mixed solid phases as the number of waxy components. In binary mixtures, the solid rich in the lighter component contains little of the heavier component but the second phase shows sub......-temperature and low-temperature forms, are pure. Model calculations compare well with the data of Pauly et al. for C18 to C30 waxes precipitating from n-decane solutions. (C) 2004 American Institute of Chemical Engineers....

Biodegradation of Alaska North Slope crude oil enhanced by commercial bioremediation agents

International Nuclear Information System (INIS)

Aldrett, S.; Bonner, J.S.; Mills, M.A.; McDonald, T.J.; Autenrieth, R.L.

1996-01-01

The biodegradation of crude oil was studied. Tests were conducted in which natural unpolluted seawater was collected and then contaminated with Alaska North Slope crude oil. The oil was weathered by heating it to 521 degrees F to remove the light-end hydrocarbons. A total of 13 different bioremediation agents were tested, each one separately. Three samples per treatment were destructively analysed for petroleum chemistry. The thirteen treatments were analyzed for oil and grease. It was found that microbial degradation of petroleum hydrocarbons was enhanced by the addition of bioremediation agents, but it was not possible to identify the intermediate products responsible for the increase of resolved petroleum hydrocarbons through time. It was suggested that caution be used when interpreting results since the protocols used to test the products were prone to uncontrollable variations. 11 refs., 5 tabs., 6 figs

Accuracy of ringless casting and accelerated wax-elimination technique: a comparative in vitro study.

Science.gov (United States)

Prasad, Rahul; Al-Keraif, Abdulaziz Abdullah; Kathuria, Nidhi; Gandhi, P V; Bhide, S V

2014-02-01

The purpose of this study was to determine whether the ringless casting and accelerated wax-elimination techniques can be combined to offer a cost-effective, clinically acceptable, and time-saving alternative for fabricating single unit castings in fixed prosthodontics. Sixty standardized wax copings were fabricated on a type IV stone replica of a stainless steel die. The wax patterns were divided into four groups. The first group was cast using the ringless investment technique and conventional wax-elimination method; the second group was cast using the ringless investment technique and accelerated wax-elimination method; the third group was cast using the conventional metal ring investment technique and conventional wax-elimination method; the fourth group was cast using the metal ring investment technique and accelerated wax-elimination method. The vertical marginal gap was measured at four sites per specimen, using a digital optical microscope at 100× magnification. The results were analyzed using two-way ANOVA to determine statistical significance. The vertical marginal gaps of castings fabricated using the ringless technique (76.98 ± 7.59 μm) were significantly less (p castings fabricated using the conventional metal ring technique (138.44 ± 28.59 μm); however, the vertical marginal gaps of the conventional (102.63 ± 36.12 μm) and accelerated wax-elimination (112.79 ± 38.34 μm) castings were not statistically significant (p > 0.05). The ringless investment technique can produce castings with higher accuracy and can be favorably combined with the accelerated wax-elimination method as a vital alternative to the time-consuming conventional technique of casting restorations in fixed prosthodontics. © 2013 by the American College of Prosthodontists.

Modeling the hydration process of bean grains coated with carnauba wax

Directory of Open Access Journals (Sweden)

Aline Almeida da Paixão

2017-08-01

Full Text Available Edible waxes are widely used to maintain foodstuff until they are consumed. However, some products may be subjected to industrial procedures, such as hydration, prior to their consumption. Hydration of a material is a complex process, which aims to reconstitute the original characteristics of a product when in contact with a liquid phase. An important agricultural product that requires this procedure is beans. Thus, the purpose of this work is to study the hydration process of beans (cultivar BRSMG Majestoso in different temperatures and concentrations of carnauba wax, which is applied on the product surface. Beans with initial moisture content of 0.2015, 0.1972 and 0.1745 (d.b. corresponding to treatments 0 (witness, 1 (wax diluted in water in the ratio 1:1, and 2 (carnauba wax, without dilution were used. Later, these samples were imbibed in distilled water at temperatures of 20, 30 and 40 ºC, for 15 h. The temperature and the carnauba wax influenced the water absorption rate. The Peleg model described satisfactory experimental data and the Mitscherlich model presented biased residual distribution. The constants C1 and C2 of the Peleg model exhibited opposite behaviors with increasing temperatures in the hydration process.

Jojoba - a promising plant for the semi-arid regions. [North America, plants, seeds, oils, waxes, growth, cultivation, lubricants, guayule, mesquite

Energy Technology Data Exchange (ETDEWEB)

Yermanos, D.M.

1979-01-01

As a result of the world-wide concern for conservation of resources and for the development of new renewable resources a great deal of attention has been directed towards the development of jojoba as a potential new crop for semi-arid regions. Jojoba grows wild in the Southwestern U.S. and N. Mexico, in areas where the annual precipitation is 4''-15''. Under cultivation it appears to grow satisfactorily in areas of marginal soil fertility, high salinity and high atmospheric temperatures. It appears to have no major natural enemies and to be tolerant to chemical treatments, if they were to become necessary. It is perennial with an assumed life span in excess of 150 years. Jojoba seed has an average weight of about 0.5 grams per seed, and it contains a unique liquid wax which is a superior lubricant and a potential replacement of whale oil, obtained from the sperm whale, and endangered species. Thus, jojoba has a double appeal, first as a potential crop of semi-arid regions requiring low cultural and energy inputs and second as a source of a valuable commodity. It should be pointed out that a cheap and abundant source of lubricants will disappear when our stock of fossil fuels are exhausted and that none of our new sources of energy have lubricants as by-products. Finally, jojoba could be grown with other companion crops such as guayule or mesquite for more diversified farming.

Responses of low pressure Andersen sampler for collecting substrates

Energy Technology Data Exchange (ETDEWEB)

Yamasaki, K. [Research Reactor Institute, Kyoto University, Osaka (Japan); Yamada, Y.; Miyamoto, K.; Shimo, M. [Division of Radiotoxicology and Protection, National Institute of Radiological Sciences, Chiba (Japan)

2000-05-01

Some types of low pressure cascade impactors (Andersen, Berner, Davies, and MOUDI etc) have been used to measure the activity size distribution of radon progeny in the environment. In spite of their careful uses, their nonideal responses are not adequately known. Some important factors such as the wall loss, electrostatic attraction, and the surface nature of collecting substrates may affect the reliability of the impactor data. Size selective characteristics of a low pressure Andersen sampler for various collecting substrates were examined in a radon exposure chamber using several kinds of liquid (DOS) or solid (carnauba wax) carrier aerosols labelled with radon progeny. These carrier aerosols were produced by commercial condensation aerosol generator. Tested collecting substrates were, (1) uncoated clean stainless steel plate, (2) silicone oil or grease coated stainless steel plate, (3) polyethylene sheet covered stainless steel plate, (4) membrane filter, (5) glass fiber filter, and (6) quartz fiber filter. In the case of collecting liquid or sticky carrier aerosols, the effect of particle bounce was small and nearly any substrates might used on the impaction plate. On the other hand, in the case of solid carrier aerosols, an adhesive layer such as grease or oil might have to be applied to the substrate. It was concluded that a low pressure cascade impactor such as Andersen sampler might need an appropriate calibration procedure including the interstage characteristics for determining the accurate activity size distribution. (author)

Caffeine and theobromine in epicuticular wax of Ilex paraguariensis A. St.-Hil.

Science.gov (United States)

Athayde, M L; Coelho, G C; Schenkel, E P

2000-12-01

Caffeine and theobromine were identified and quantified in leaf epicuticular waxes of Ilex paraguariensis A. St.-Hil. (Aquifoliaceae). The total epicuticular leaf wax content was ca. 0.5% on average of dry leaf weight. Epicuticular caffeine and theobromine contents varied from 0.16 to 127.6 microg/mg and from 0 to 9.5 microg/mg of wax, respectively. For some selected samples, the intracellular methylxanthine concentration was also determined. A positive correlation was found between inner and epicuticular caffeine contents.

Changes in Cuticular Wax Composition of Two Blueberry Cultivars during Fruit Ripening and Postharvest Cold Storage.

Science.gov (United States)

Chu, Wenjing; Gao, Haiyan; Chen, Hangjun; Wu, Weijie; Fang, Xiangjun

2018-03-21

Cuticular wax plays an important role for the quality of blueberry fruits. In this study, the cuticular wax composition of two blueberry cultivars, 'Legacy' ( Vaccinium corymbosum) and 'Brightwell' ( Vaccinium ashei), was examined during fruit ripening and postharvest cold storage. The results showed that wax was gradually deposited on the epidermis of blueberry fruits and the content of major wax compounds, except that for diketones, increased significantly during fruit ripening. The total wax content was 2-fold greater in 'Brightwell' blueberries than that in 'Legacy' blueberries during fruit ripening. The total wax content of both cultivars decreased during 30 days of storage at 4 °C, and the variation of cuticular wax composition was cultivar-dependent. The content of diketones decreased significantly in 'Legacy' blueberries, while the content of triterpenoids and aliphatic compounds showed different fold changes in 'Brightwell' blueberries after 30 days of storage at 4 °C. Overall, our study provided a quantitative and qualitative overview of cuticular wax compounds of blueberry fruits during ripening and postharvest cold storage.

Study of phase transition in hard microcrystalline waxes and wax blends by differential scanning calorimetry

Czech Academy of Sciences Publication Activity Database

Kumar, S.; Agrawal, K. M.; Khan, H. U.; Sikora, Antonín

2004-01-01

Roč. 22, 3 & 4 (2004), s. 337-345 ISSN 1091-6466 R&D Projects: GA AV ČR KSK4050111 Institutional research plan: CEZ:AV0Z4050913 Keywords : phase transition * hard microscrystalline waxes * differential scanning calorimetry Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.312, year: 2004

Effects of sunflower wax coating on physicochemical changes of mangifera indica L. in storage life

International Nuclear Information System (INIS)

Soomro, R.K.; Sherazi, S.T.H.

2013-01-01

Mango (Mangifera indica L.) fruit has a relatively short storage life due to perishable nature. In order to increases the storage life of langra mangoes, fruits were coated with sunflower wax. Mangoes were stored at room and refrigerated temperature. Sunflower wax coating protects the mangoes in greater proportion to change their color, weight loss, moisture loss, pH and total soluble solids content. The sensorial panel also favors the grander role of sunflower wax coating. Application of sunflower wax coatings had no effect on vitamin C content of mangoes variety and could increases mango storage time around 30 days under regular storage conditions. Sunflower wax coating also inhibited the growth of micro-organisms. The data reveal that by applying a sunflower wax coating effectively prolongs the quality which attributes and extends the shelf life of mango. (author)

McWRI1, a transcription factor of the AP2/SHEN family, regulates the biosynthesis of the cuticular waxes on the apple fruit surface under low temperature

Science.gov (United States)

Ji, Qianlong; Zhang, Kezhong; Yang, Mingfeng

2017-01-01

Cuticular waxes of plant and organ surfaces play an important role in protecting plants from biotic and abiotic stress and extending the freshness, storage time and shelf life in the post-harvest agricultural products. WRI1, a transcription factor of AP2/SHEN families, had been found to trigger the related genes taking part in the biosynthesis of seed oil in many plants. But whether WRI1 is involved in the biosynthesis of the cuticular waxes on the Malus fruits surface has been unclear. We investigated the changes of wax composition and structure, the related genes and WRI1 expression on Malus asiatica Nakai and sieversii fruits with the low temperature treatments, found that low temperature induced the up-regulated expression of McWRI1, which promoted gene expression of McKCS, McLACs and McWAX in very-long-chain fatty acid biosynthesis pathway, resulting in the accumulation of alkanes component and alteration of wax structure on the fruit surface. Corresponding results were verified in McWRI1 silenced by VIGS, and WRI1 silenced down-regulated the related genes on two kinds of fruits, it caused the diversity alteration in content of some alkanes, fatty acid and ester component in two kinds of fruits. We further conducted Y1H assay to find that McWRI1 transcription factor activated the promoter of McKCS, McLAC and McWAX to regulate their expression. These results demonstrated that McWRI1 is involved in regulating the genes related synthesis of very long chain fatty acid on surface of apple fruits in storage process, providing a highlight for improvement of the modified atmosphere storage of apple fruits. PMID:29073205

GC-MS Metabolomics to Evaluate the Composition of Plant Cuticular Waxes for Four Triticum aestivum Cultivars

Directory of Open Access Journals (Sweden)

Florent D. Lavergne

2018-01-01

Full Text Available Wheat (Triticum aestivum L. is an important food crop, and biotic and abiotic stresses significantly impact grain yield. Wheat leaf and stem surface waxes are associated with traits of biological importance, including stress resistance. Past studies have characterized the composition of wheat cuticular waxes, however protocols can be relatively low-throughput and narrow in the range of metabolites detected. Here, gas chromatography-mass spectrometry (GC-MS metabolomics methods were utilized to provide a comprehensive characterization of the chemical composition of cuticular waxes in wheat leaves and stems. Further, waxes from four wheat cultivars were assayed to evaluate the potential for GC-MS metabolomics to describe wax composition attributed to differences in wheat genotype. A total of 263 putative compounds were detected and included 58 wax compounds that can be classified (e.g., alkanes and fatty acids. Many of the detected wax metabolites have known associations to important biological functions. Principal component analysis and ANOVA were used to evaluate metabolite distribution, which was attributed to both tissue type (leaf, stem and cultivar differences. Leaves contained more primary alcohols than stems such as 6-methylheptacosan-1-ol and octacosan-1-ol. The metabolite data were validated using scanning electron microscopy of epicuticular wax crystals which detected wax tubules and platelets. Conan was the only cultivar to display alcohol-associated platelet-shaped crystals on its abaxial leaf surface. Taken together, application of GC-MS metabolomics enabled the characterization of cuticular wax content in wheat tissues and provided relative quantitative comparisons among sample types, thus contributing to the understanding of wax composition associated with important phenotypic traits in a major crop.

Sand or grease? Corruption-institutional trust nexus in post-Soviet countries

OpenAIRE

Nazim Habibov; Elvin Afandi; Alex Cheung

2017-01-01

This paper empirically tests several hypotheses about the nexus of corruption-institutional trust in Post-Soviet transitional countries of the former Soviet Union and Mongolia. We use two different indices of institutional trust to check the robustness of our analysis and estimate OLS and instrumental variable models with and without interaction terms. All things considered, our findings reject “greases the wheels” and “trust begets an honest political system” hypotheses. Instead, our finding...

Waxes and plastic film in relation to the shelf life of yellow passion fruit

Directory of Open Access Journals (Sweden)

Mota Wagner Ferreira da

2003-01-01

Full Text Available The high perishability of the yellow passion fruit (Passiflora edulis f. flavicarpa reduces its postharvest conservation and availability, mainly for in natura consumption. These losses of quality and commercial value occur due to the high respiration and loss of water. This work aimed to evaluate the influence of a modified atmosphere - wax emulsions and plastic film - on the shelf life of the yellow passion fruit. Plastic film (Cryovac D-955, 15 mum thickness reduced fresh weight loss and fruit wilting, kept higher fruit and rind weight and higher pulp osmotic potential over the storage period. However, it was not efficient in the control of rottenness. Sparcitrus wax (22-23% polyethylene/maleyc resin caused injury to the fruit, high fruit weight losses and wilting and resulted in lower pulp osmotic potential; this wax lead to a higher concentration of acid and a lower relation of soluble solids/acidity. Among the tested waxes, Fruit Wax (18-21% carnauba wax was the best, promoting reduced weight loss, wilting and rottenness.

Contribution to the study of the physical stability of the suspensions of zinc oxide, titanium dioxide and precipitated sulphur employing emulsified solid greases like vehicle

International Nuclear Information System (INIS)

Porras Navarro, Martha

2001-01-01

This research evaluated the physical stability of the suspensions of zinc oxide, precipitated sulphur and titanium dioxide. By using emulsified vehicles of three solid greases: stearilic alcohol, stearic acid and beeswax. That varies the concentration of solid grease (2%, 4%, 6 %) and the velocity of agitation for the emulsified vehicle's preparation (250, 500, 750 revolutions by minutes). That got 81 suspensions, 27 for every grease employed. The following effects there were evaluated like indicators of the physical stability of the suspensions: volume of sediment, apparent viscosity, facility of resuspension. There was effected an analysis of the varying of two controlled factors to establish the importance since the statistical viewpoint of the variants of the process over the volume of the sediment. This study indicates that the selection of solid grease is an parameter which influence is significant, what supports the got data through the research. By giving as a result that the stearilic alcohol is the most competent vehicle for the preparation of these suspensions. (Author) [es

Anatomically realistic ultrasound phantoms using gel wax with 3D printed moulds

Science.gov (United States)

Maneas, Efthymios; Xia, Wenfeng; Nikitichev, Daniil I.; Daher, Batol; Manimaran, Maniragav; Wong, Rui Yen J.; Chang, Chia-Wei; Rahmani, Benyamin; Capelli, Claudio; Schievano, Silvia; Burriesci, Gaetano; Ourselin, Sebastien; David, Anna L.; Finlay, Malcolm C.; West, Simeon J.; Vercauteren, Tom; Desjardins, Adrien E.

2018-01-01

Here we describe methods for creating tissue-mimicking ultrasound phantoms based on patient anatomy using a soft material called gel wax. To recreate acoustically realistic tissue properties, two additives to gel wax were considered: paraffin wax to increase acoustic attenuation, and solid glass spheres to increase backscattering. The frequency dependence of ultrasound attenuation was well described with a power law over the measured range of 3-10 MHz. With the addition of paraffin wax in concentrations of 0 to 8 w/w%, attenuation varied from 0.72 to 2.91 dB cm-1 at 3 MHz and from 6.84 to 26.63 dB cm-1 at 10 MHz. With solid glass sphere concentrations in the range of 0.025-0.9 w/w%, acoustic backscattering consistent with a wide range of ultrasonic appearances was achieved. Native gel wax maintained its integrity during compressive deformations up to 60%; its Young’s modulus was 17.4  ±  1.4 kPa. The gel wax with additives was shaped by melting and pouring it into 3D printed moulds. Three different phantoms were constructed: a nerve and vessel phantom for peripheral nerve blocks, a heart atrium phantom, and a placental phantom for minimally-invasive fetal interventions. In the first, nerves and vessels were represented as hyperechoic and hypoechoic tubular structures, respectively, in a homogeneous background. The second phantom comprised atria derived from an MRI scan of a patient with an intervening septum and adjoining vena cavae. The third comprised the chorionic surface of a placenta with superficial fetal vessels derived from an image of a post-partum human placenta. Gel wax is a material with widely tuneable ultrasound properties and mechanical characteristics that are well suited for creating patient-specific ultrasound phantoms in several clinical disciplines.

A comparative evaluation of the marginal adaptation of a thermoplastic resin, a light cured wax and an inlay casting wax on stone dies: An in vitro study.

Science.gov (United States)

Gopalan, Reji P; Nair, Vivek V; Harshakumar, K; Ravichandran, R; Lylajam, S; Viswambaran, Prasanth

2018-01-01

Different pattern materials do not produce copings with satisfactory, marginal accuracy when used on stone dies at varying time intervals. The purpose of this study was to evaluate and compare the vertical marginal accuracy of patterns formed from three materials, namely, thermoplastic resin, light cured wax and inlay casting wax at three-time intervals of 1, 12, and 24 h. A master die (zirconia abutment mimicking a prepared permanent maxillary central incisor) and metal sleeve (direct metal laser sintering crown #11) were fabricated. A total of 30 stone dies were obtained from the master die. Ten patterns were made each from the three materials and stored off the die at room temperature. The vertical marginal gaps were measured using digital microscope at 1, 12, and 24 h after reseating with gentle finger pressure. The results revealed a significant statistical difference in the marginal adaptation of three materials at all the three-time intervals. Light cured wax was found to be most accurate at all time intervals, followed by thermoplastic resin and inlay casting wax. Furthermore, there was a significant difference between all pairs of materials. The change in vertical marginal gap from 1 to 24 h between thermoplastic resin and light cured wax was not statistically significant. The marginal adaptation of all the three materials used, was well within the acceptable range of 25-70 μm. The resin pattern materials studied revealed significantly less dimensional change than inlay casting wax on storage at 1, 12, and 24 h time intervals. They may be employed in situations where high precision and delayed investing is expected.

Three-dimensional wax patterning of paper fluidic devices.

Science.gov (United States)

Renault, Christophe; Koehne, Jessica; Ricco, Antonio J; Crooks, Richard M

2014-06-17

In this paper we describe a method for three-dimensional wax patterning of microfluidic paper-based analytical devices (μPADs). The method is rooted in the fundamental details of wax transport in paper and provides a simple way to fabricate complex channel architectures such as hemichannels and fully enclosed channels. We show that three-dimensional μPADs can be fabricated with half as much paper by using hemichannels rather than ordinary open channels. We also provide evidence that fully enclosed channels are efficiently isolated from the exterior environment, decreasing contamination risks, simplifying the handling of the device, and slowing evaporation of solvents.

Frictional properties of lubrication greases with the addition of nickel nanoparticles in pneumatic cylinder

Science.gov (United States)

Chang, Ho; Lan, Chou-Wei; Guo, Jia-Bin

2011-12-01

This paper studies the influence of addition of 100 nm diameter nickel nano-particles on the friction properties of synthetic grease (Li base, VG100) in pneumatic cylinder. The friction force test of pneumatic cylinder equipment measures the frictional force between seal and cylinder bore in pneumatic cylinders. The lubricants with addition of nickel nano-particles were used for lubricating the contact interface between seal and cylinder bore. The friction force test equipment employ a load cell force sensor to measure the friction force between seals and cylinder bores. Results obtained from experimental tests are compared to determine the friction force between seals and cylinder bore in pneumatic cylinders. The study leads to the conclusion that the addition of nickel nano-particles to synthetic grease results in a decrease in friction force between seals and cylinder bores in pneumatic cylinder. This tribological behavior is closely related to the deposition of nano-particles on the rubbing surfaces

Improved surfactants formulation for remediation of oil sludge recovery

International Nuclear Information System (INIS)

Syed Hakimi Sakuma Syed Ahmad; Shahidan Radiman

2000-01-01

Surfactant enhanced remediation based on mobilisation of the residual NAPLs (oil sludge) which is radioactive depends on the tendency of the surfactants to lower interfacial tension. Mobilisation has greater potential than solubilisation to increase the rate of remediation. Optimised surfactants formulation was determined with concentration of Aqua 2000 and D Bond of 1% wt respectively, sodium chloride concentration of 2 gmL -1 and addition of 3% wt butanol as cosolvent. The formulation was of benefit not only able to decrease further the interfacial tension of aqueous solution containing oil emulsion, but also to make possible to be more mobile and destruction of mixed liquid crystals that formed. Formation of liquid crystals can hinders significantly recovery efficiency of aqueous solution containing oil emulsion in field remediation work. In a 100 litres soil column experiment conducted containing oil emulsion in field sludge soil and using the surfactants formulation for flushing, miniemulsion formed sizes maintained at average size between 125 nm and 280 nm before and after remediation. Total oil and grease concentration removed from the soil were significant due to the decreased in oil emulsion sizes, increase mobility and solubility. (Author)

Applications of micro-SAXS/WAXS to study polymer fibers

International Nuclear Information System (INIS)

Riekel, C.

2003-01-01

Instrumentation and selected applications for X-ray microdiffraction experiments on polymer and biopolymer fibers at the European Synchrotron Radiation Facility (ESRF) microfocus beamline are reviewed. Combined SAXS/WAXS experiments can be performed on single fibers with a beam size down to about 5 μm. WAXS experiments can be performed down to about 2 μm and in exceptional cases down to 0.1 μm beam size. The instrumental possibilities are demonstrated for the production line of spider silk

Applications of micro-SAXS/WAXS to study polymer fibers

Energy Technology Data Exchange (ETDEWEB)

Riekel, C. E-mail: riekel@esrf.fr

2003-01-01

Instrumentation and selected applications for X-ray microdiffraction experiments on polymer and biopolymer fibers at the European Synchrotron Radiation Facility (ESRF) microfocus beamline are reviewed. Combined SAXS/WAXS experiments can be performed on single fibers with a beam size down to about 5 {mu}m. WAXS experiments can be performed down to about 2 {mu}m and in exceptional cases down to 0.1 {mu}m beam size. The instrumental possibilities are demonstrated for the production line of spider silk.

Applications of micro-SAXS/WAXS to study polymer fibers

Science.gov (United States)

Riekel, C.

2003-01-01

Instrumentation and selected applications for X-ray microdiffraction experiments on polymer and biopolymer fibers at the European Synchrotron Radiation Facility (ESRF) microfocus beamline are reviewed. Combined SAXS/WAXS experiments can be performed on single fibers with a beam size down to about 5 μm. WAXS experiments can be performed down to about 2 μm and in exceptional cases down to 0.1 μm beam size. The instrumental possibilities are demonstrated for the production line of spider silk.

A new green process for biodiesel production from waste oils via catalytic distillation using a solid acid catalyst – Modeling, economic and environmental analysis

Directory of Open Access Journals (Sweden)

Aashish Gaurav

2016-04-01

Full Text Available The challenges in the chemical processing industry today are environmental concerns, energy and capital costs. Catalytic distillation (CD is a green reactor technology which combines a catalytic reaction and separation via distillation in the same distillation column. Utilization of CD in chemical process development could result in capital and energy savings, and the reduction of greenhouse gases. The efficacy of CD and the economic merits, in terms of energy and equipment savings, brought by CD for the production of biodiesel from waste oil such as yellow grease is quantified. Process flow sheets for industrial routes for an annual production of 10 million gallon ASTM purity biodiesel in a conventional process (reactor followed by distillation and CD configurations are modeled in Aspen Plus. Material and energy flows, as well as sized unit operation blocks, are used to conduct an economic assessment of each process. Total capital investment, total operating and utility costs are calculated for each process. The waste oil feedstock is yellow grease containing both triglyceride and free fatty acid. Both transesterification and esterification reactions are considered in the process simulations. Results show a significant advantage of CD compared to a conventional biodiesel processes due to the reduction of distillation columns, waste streams and greenhouse gas emissions. The significant savings in capital and energy costs together with the reduction of greenhouse gases demonstrate that process intensification via CD is a feasible and new green process for the biodiesel production from waste oils. Keywords: Yellow grease, Catalytic distillation, Aspen plus economic analyzer, Process intensification

Cuticular waxes in alpine meadow plants: climate effect inferred from latitude gradient in Qinghai-Tibetan Plateau.

Science.gov (United States)

Guo, Yanjun; Guo, Na; He, Yuji; Gao, Jianhua

2015-09-01

Alpine meadow ecosystems are susceptible to climate changes. Still, climate impact on cuticular wax in alpine meadow plants is poorly understood. Assessing the variations of cuticular wax in alpine meadow plants across different latitudes might be useful for predicting how they may respond to climate change. We studied nine alpine meadows in a climate gradient in the east side of Qinghai-Tibetan Plateau, with mean annual temperature ranging from -7.7 to 3.2°C. In total, 42 plant species were analyzed for cuticular wax, averaged 16 plant species in each meadow. Only four plant species could be observed in all sampling meadows, including Kobresia humilis,Potentilla nivea,Anaphalis lacteal, and Leontopodium nanum. The amounts of wax compositions and total cuticular wax in the four plant species varied among sampling meadows, but no significant correlation could be observed between them and temperature, precipitation, and aridity index based on plant species level. To analyze the variations of cuticular wax on community level, we averaged the amounts of n-alkanes, aliphatic acids, primary alcohols, and total cuticular wax across all investigated plant species in each sampling site. The mean annual temperature, mean temperature in July, and aridity index were significantly correlated with the averaged amounts of wax compositions and total cuticular wax. The average chain length of n-alkanes in both plant and soil linearly increased with increased temperature, whereas reduced with increased aridity index. No significant correlation could be observed between mean annual precipitation and mean precipitation from June to August and the cuticular wax amounts and average chain length. Our results suggest that the survival of some alpine plants in specific environments might be depended on their abilities in adjusting wax deposition on plant leaves, and the alpine meadow plants as a whole respond to climate change, benefiting the stability of alpine meadow ecosystem.

Composition of the epicuticular and intracuticular wax layers on Kalanchoe daigremontiana (Hamet et Perr. de la Bathie) leaves.

Science.gov (United States)

van Maarseveen, Clare; Jetter, Reinhard

2009-05-01

Epicuticular and intracuticular waxes from both adaxial and abaxial surfaces of the leaves of Kalanchoe daigremontiana were analyzed. All wax mixtures were found to contain approximately equal amounts of triterpenoids and very long chain fatty acid (VLCFA) derivatives. The triterpenoid fraction consisted of glutinol (8-19% of the total wax) and friedelin (4-9%), together with smaller amounts of glutanol, glutinol acetate, epifriedelanol, germanicol and beta-amyrin. The VLCFA derivatives comprised C27-C35 alkanes (19-37% of the total wax), C32-C34 aldehydes (3-7%), C32 and C34 fatty acids (0.2-3%), C26-C36 primary alcohols (4-8%), and C42-C52 alkyl esters (2-9%). The wax layers were found to differ in triterpenoid amounts, with the intracuticular wax containing higher percentages of most triterpenoids than the epicuticular wax. Friedelin, the only triterpenoid ketone present, showed the opposite distribution with higher proportions in the epicuticular wax. VLCFA derivatives also accumulated to higher percentages in the epicuticular than in the intracuticular wax layer. Epicuticular wax crystals were observed on both the adaxial and abaxial leaf surfaces.

The deformation of wax patterns and castings in investment casting technology

Directory of Open Access Journals (Sweden)

A. Herman

2012-01-01

Full Text Available The dimensional accuracy of the final casting of Inconel alloy 738 LC is affected by many aspects. One of them is the choice of method and time of cooling wax model for precision investment casting. The main objective was to study the initial deformation of the complex shape of the casting of the rotor blades. Various approaches have been tested for cooling wax pattern. When wax models are cooling on the air, without clamping in jig for cooling, deviations from the ideal shape of the casting are very noticeable (up to 8 mm and most are in extreme positions of the model. When blade is cooled in fixing jig in water environment, the resulting deviations compared with cooling in air are significantly larger, sometimes up to 10 mm. This itself does not mean that the final shape of the casting is dimensionally more accurate with usage of wax models, which have deviations from the ideal position smaller. Another deformation occurs when shell mould is produced around wax pattern and furthermore deformations emerge while casting of blade is cooling. This paper demonstrates first steps in describing complex process of deformations of Inconel alloy blades produced with investment casting technology by comparing results from thermal imagery, simulations in foundry simulation software ProCAST 2010 and measurements from CNC scanning system Carl Zeiss MC 850. Conclusions are so far not groundbreaking, but it seems deformations of wax pattern and deformations of castings do in some cases cancel each other by having opposite directions. Describing entirely whole process of deformations will help increase precision of blade castings so that models at the beginning and blades in the end are the same.

Effects of Wax Coating on the Moisture Loss of Cucumbers at Different Storage Temperatures

Directory of Open Access Journals (Sweden)

Jian Li

2018-01-01

Full Text Available The effects of wax coating on moisture loss of cucumbers (Cucumis sativus L., cv. Jinglv were investigated at different temperatures. Cucumbers were treated with 10% (volume : volume wax and then stored at 15, 20, 25, or 30°C and 55% relative humidity. The changes in the mass of samples were recorded every 6 h. Results showed that wax coating along with low temperature was very effective in preventing moisture loss of cucumbers during simulated distribution. After 48 h storage, moisture loss in wax treated cucumbers at 15°C was 45% lower than the control at 30°C. Furthermore, a kinetic model was developed to study the influence of temperature on moisture loss based on the Arrhenius law. The model successfully described changes in cucumber moisture loss at different temperatures during storage. The shelf life of cucumber was also predicted using the kinetic model. A synergistic effect was found between wax coating and storage temperature on cucumber shelf life. Wax coating combined with low storage temperature was an effective method to extend the shelf life of cucumber fruit.

Co-metabolism of DDT by the newly isolated bacterium, Pseudoxanthomonas sp. wax

Directory of Open Access Journals (Sweden)

Guangli Wang

2010-06-01

Full Text Available Microbial degradation of 1,1,1-trichloro-2,2-bis(p-chlorophenylethane (DDT is the most promising way to clean up DDT residues found in the environment. In this paper, a bacterium designated as wax, which was capable of co-metabolizing DDT with other carbon sources, was isolated from a long-term DDT-contaminated soil sample by an enrichment culture technique. The new isolate was identified as a member of the Pseudoxanthomonas sp., based on its morphological, physiological and biochemical properties, as well as by 16S rRNA gene analysis. In the presence of 100 mg l-1 glucose, the wax strain could degrade over 95% of the total DDT, at a concentration of 20 mg l-1, in 72 hours, and could degrade over 60% of the total DDT, at a concentration of 100 mg l-1, in 144 hours. The wax strain had the highest degradation efficiency among all of the documented DDT-degrading bacteria. The wax strain could efficiently degrade DDT at temperatures ranging from 20 to 37ºC, and with initial pH values ranging from 7 to 9. The bacterium could also simultaneously co-metabolize 1,1-dichloro-2,2-bis(p-chlorophenylethane (DDD, 2,2-bis(p-chlorophenyl-1,1-dichlorethylene (DDE, and other organochlorine compounds. The wax strain could also completely remove 20 mg kg-1 of DDT from both sterile and non-sterile soils in 20 days. This study demonstrates the significant potential use of Pseudoxanthomonas sp. wax for the bioremediation of DDT in the environment.

Caracterización de una biograsa de aceite vegetal de Jatropha curcas L y jabón de litio//Characterization of biogrease based on Jatropha curcas L vegetable oil and Lithium Soap Thickener

Directory of Open Access Journals (Sweden)

Juliano Chitue de Assunção Nascimento

2013-05-01

Full Text Available Los aceites vegetales poseen un gran potencial como fluido base y como sustituto de los aceites minerales para la formulación de grasas lubricantes, estos aceites son biodegradables y renovables. En el trabajo se determinaron las propiedades  fisicoquímicas, antidesgaste y de extrema presión de una biograsa de aceite vegetal de Jatropha curcas L y jabón de litio empleando los métodos de pruebas estándar para las grasas lubricantes. La biograsa posee un color amarillo claro, una textura suave y homogénea,  un grado de penetración NLGI 1, una temperatura de goteo de 145 oC, magnitudes adecuadas del contenido de álcalis libre y corrosión al cobre; así como  propiedades antidesgaste y de extrema presión similares a otras grasas minerales y biograsas formuladas con diferentes aceites vegetales. Palabras claves: biograsa, aceite de Jatropha curcas L, jabón de litio, propiedades fisicoquímicas, propiedades antidesgaste, propiedades de extrema presión. Characterization of biogrease based on Jatropha curcas L vegetable oil and Lithium Soap Thickener. Abstract Vegetable oils have a great potential as a base fluid and a substitute for mineral oil in grease formulation, these oils are biodegradable and renewable. In this paper were determined the  physicochemical, antiwear and extreme pressure properties of a biogrease based on Jatropha curcas L vegetable oil and lithium soap thickener using the lubricanting greases standard test methods. The biogrease have a light yellow color, soft and homogeneous texture, a penetration grade NLGI 1, a drop point of 145 oC, appropriate magnitudes of free alkalis and copper corrosion; as well as antiwear and extreme pressure properties similar to the other mineral lubricating grease and formulated biogreases with differents vegetable oils. Key words: biogrease, Jatropha curcas L vegetable oil, lithium soap thickener, physicochemical properties, antiwear properties, extreme pressure properties.

Numerical performance study of paraffin wax dispersed with alumina in a concentric pipe latent heat storage system

Directory of Open Access Journals (Sweden)

Valan Arasu Amirtham

2013-01-01

Full Text Available Latent heat energy storage systems using paraffin wax could have lower heat transfer rates during melting/freezing processes due to its inherent low thermal conductivity. The thermal conductivity of paraffin wax can be enhanced by employing high conductivity materials such as alumina (Al2O3. A numerical analysis has been carried out to study the performance enhancement of paraffin wax with nanoalumina (Al2O3 particles in comparison with simple paraffin wax in a concentric double pipe heat exchanger. Numerical analysis indicates that the charge-discharge rates of thermal energy can be greatly enhanced using paraffin wax with alumina as compared with a simple paraffin wax as PCM.

Epicuticular waxes from caatinga and cerrado species and their efficiency against water loss

Directory of Open Access Journals (Sweden)

Oliveira Antonio F. M.

2003-01-01

Full Text Available The effects of the contents and chemical composition of the foliar epicuticular waxes of species from the caatinga (Aspidosperma pyrifolium, Capparis yco, Maytenus rigida and Ziziphus joazeiro and cerrado (Aristolochia esperanzae, Didymopanax vinosum, Strychnos pseudoquina and Tocoyena formosa were evaluated as to the resistance to water loss by means of an experimental device constructed for this purpose. In general, the waxes of the caatinga species investigated were more efficient against water loss than cerrado species. Increase of the thickness of the waxy deposits from 40 to 90m g.cm-2 had no significant effect on the resistance to water loss. The chemistry of the wax constituents was shown to be an important factor to determine the degree of resistance to evaporation. n-Alkanes and alcoholic triterpenes were the most efficient barriers, while hentriacontan-16-one (a ketone and ursolic acid (an acid triterpene revealed lowefficiency. The higher efficiency of the waxes of the leaves from caatinga species (mainly those of C. yco and Z. joazeiro is probably accounted for the predominance of n-alkanes in their composition. The lower efficiency of the waxes of A. pyrifolium (caatinga, T. formosa and A. esperanzae (both species from the cerrado is probably a consequence of the predominance of triterpenoids in the waxes of the two former species and hentriacontan-16-one in the latter.

Influences of Restaurant Waste Fats and Oils (RWFO from Grease Trap as Binder on Rheological and Solvent Extraction Behavior in SS316L Metal Injection Molding

Directory of Open Access Journals (Sweden)

Mohd Halim Irwan Ibrahim

2016-02-01

Full Text Available This article deals with rheological and solvent extraction behavior of stainless steel 316L feedstocks using Restaurant Waste Fats and Oils (RWFO from grease traps as binder components along with Polypropylene (PP copolymer as a backbone binder. Optimal binder formulation and effect of solvent extraction variables on green compacts are being analyzed. Four binder formulations based on volumetric ratio/weight fraction between PP and RWFO being mixed with 60% volumetric powder loading of SS316L powder each as feedstock. The rheological analysis are based on viscosity, shear rate, temperature, activation energy, flow behavior index, and moldability index. The optimal feedstock formulation will be injected to form green compact to undergo the solvent extraction process. Solvent extraction variables are based on solvent temperature which are 40 °C, 50 °C, and 60 °C with different organic solvents of n-hexane and n-heptane. Analysis of the weight loss percentage and diffusion coefficient is done on the green compact during the solvent extraction process. Differential Scanning Calorimeter (DSC is used to confirm the extraction of the RWFO in green compacts. It is found that all binder fractions exhibit pseudoplastic behavior or shear thinning where the viscosity decreases with increasing shear rate. After considering the factors that affect the rheological characteristic of the binder formulation, feedstock with binder formulation of 20/20 volumetric ratio between PP and RWFO rise as the optimal binder. It is found that the n-hexane solvent requires less time for extracting the RWFO at the temperature of 60 °C as proved by its diffusion coefficient.

Dental students' preferences and performance in crown design: conventional wax-added versus CAD.

Science.gov (United States)

Douglas, R Duane; Hopp, Christa D; Augustin, Marcus A

2014-12-01

The purpose of this study was to evaluate dental students' perceptions of traditional waxing vs. computer-aided crown design and to determine the effectiveness of either technique through comparative grading of the final products. On one of twoidentical tooth preparations, second-year students at one dental school fabricated a wax pattern for a full contour crown; on the second tooth preparation, the same students designed and fabricated an all-ceramic crown using computer-aided design (CAD) and computer-aided manufacturing (CAM) technology. Projects were graded for occlusion and anatomic form by three faculty members. On completion of the projects, 100 percent of the students (n=50) completed an eight-question, five-point Likert scalesurvey, designed to assess their perceptions of and learning associated with the two design techniques. The average grades for the crown design projects were 78.3 (CAD) and 79.1 (wax design). The mean numbers of occlusal contacts were 3.8 (CAD) and 2.9(wax design), which was significantly higher for CAD (p=0.02). The survey results indicated that students enjoyed designing afull contour crown using CAD as compared to using conventional wax techniques and spent less time designing the crown using CAD. From a learning perspective, students felt that they learned more about position and the size/strength of occlusal contacts using CAD. However, students recognized that CAD technology has limits in terms of representing anatomic contours and excursive occlusion compared to conventional wax techniques. The results suggest that crown design using CAD could be considered as an adjunct to conventional wax-added techniques in preclinical fixed prosthodontic curricula.

Role of needle surface waxes in dynamic exchange of mono- and sesquiterpenes

Directory of Open Access Journals (Sweden)

J. Joensuu

2016-06-01

Full Text Available Biogenic volatile organic compounds (BVOCs produced by plants have a major role in atmospheric chemistry. The different physicochemical properties of BVOCs affect their transport within and out of the plant as well as their reactions along the way. Some of these compounds may accumulate in or on the waxy surface layer of conifer needles and participate in chemical reactions on or near the foliage surface. The aim of this work was to determine whether terpenes, a key category of BVOCs produced by trees, can be found on the epicuticles of Scots pine (Pinus sylvestris L. and, if so, how they compare with the terpenes found in shoot emissions of the same tree. We measured shoot-level emissions of pine seedlings at a remote outdoor location in central Finland and subsequently analysed the needle surface waxes for the same compounds. Both emissions and wax extracts were clearly dominated by monoterpenes, but the proportion of sesquiterpenes was higher in the wax extracts. There were also differences in the terpene spectra of the emissions and the wax extracts. The results, therefore, support the existence of BVOC associated to the epicuticular waxes. We briefly discuss the different pathways for terpenes to reach the needle surfaces and the implications for air chemistry.

Mineral oil barrier sequential polymer treatment for recycled paper products in food packaging

Science.gov (United States)

Paul, Uttam C.; Fragouli, Despina; Bayer, Ilker S.; Mele, Elisa; Conchione, Chiara; Cingolani, Roberto; Moret, Sabrina; Athanassiou, Athanassia

2017-01-01

Recycled cellulosic paperboards may include mineral oils after the recycle process, which together with their poor water resistance limit their use as food packaging materials. In this work, we demonstrate that a proper functionalization of the recycled paper with two successive polymer treatments, imposes a mineral oil migration barrier and simultaneously renders it waterproof and grease resistant, making it an ideal material for food contact. The first poly (methyl methacrylate) treatment penetrates the paper network and creates a protective layer around every fiber, permitting thus the transformation of the paperboard to a hydrophobic material throughout its thickness, reducing at the same time the mineral oil migration. Subsequently, the second layer with a cyclic olefin copolymer fills the open pores of the surface, and reduces the mineral oil hydrocarbons migration at levels below those proposed by the BMEL. Online liquid chromatography-gas chromatography coupled with flame ionization detection quantitatively demonstrate that this dual functional treatment prevents the migration of both saturated (mineral oil saturated hydrocarbons) and aromatic hydrocarbon (mineral oil aromatic hydrocarbons) mineral oils from the recycled paperboard to a dry food simulant.

First crude oil from Chukotka

Energy Technology Data Exchange (ETDEWEB)

Arenbrister, L.P.; Demidenko, K.A.; Zhmykhova, N.M.

1986-01-01

The physicochemical properties of the crude taken from Neogene deposits at a depth of 1486-1443 m are analyzed. The oil is distinguished by low contents of sulfur and resinous-asphaltenic substances, a high content of wax, and a high yield of light cuts distilling below 350 degrees C. The naptha cuts have high contents of naphthenes, and the diesel fuel cuts have high cetane numbers, low sulfur contents, and high contents of straight chain paraffins. The vacuum gasoil has a low density, a low viscosity, a low carbon residue and low contents of sulfur and nitrogen. This gasoil is a good feedstock for catalytic cracking and hydrocracking. The Verkhne-Echin crude is classified as light, low-sulfur, lowresin and high-wax. It can be used to produce jet fuels and summer-grade diesel fuels with low sulfur contents, as well as high-V.I. lube base stocks and liquid and solid paraffins.

Experimental preliminary exploration on determining grease thickness simulated by paraffin in petroleum pipelines

International Nuclear Information System (INIS)

Zhao Nongxiao; Arkin, Abulim; Yang Kunjie; Wang Shiheng; Shi Feiyue

2009-01-01

1.25 MeV γ-ray of 60 Co Compton scattering coefficient in the simple of paraffin,are measured by γ-ray energy spectrum analysis in two determining means. At the same experimental condition, we have used this scattering coefficient to determining grease thickness simulated by paraffin. The result show the average relative difference is about 1.29% for the best group. (authors)

Characterization and chemical composition of epicuticular wax from banana leaves grown in Northern Thailand

OpenAIRE

Suporn Charumanee; Songwut Yotsawimonwat; Panee Sirisa-ard; Kiatisak Pholsongkram

2017-01-01

This study aimed to investigate the physicochemical properties and chemical composition of epicuticular wax extracted from leaves of Kluai Namwa, a banana cultivar which is widely grown in Northern Thailand. Its genotype was identified by a botanist. The wax was extracted using solvent extraction. The fatty acid profiles and physicochemical properties of the wax namely melting point, congealing point, crystal structures and polymorphism, hardness, color, and solubility were examin...

The influence of magnetic fields on crude oils viscosity

Energy Technology Data Exchange (ETDEWEB)

Goncalves, Jose L.; Bombard, Antonio J. F. [Universidade Federal de Itajuba (UNIFEI), Itajuba, MG (Brazil). Instituto de Ciencias Exatas. Lab. de Reologia

2009-07-01

The crystallization of paraffin causes serious problems in the process of transportation of petroleum. This phenomenon increases the crude oil viscosity and implies an organic resin accumulation on pipeline wall, resulting in a reduced flux area or totally blocked pipes. One of the most challenging tasks for pipeline maintenance is solving this problem at low cost. Therefore, a method that inhibits the crystallization of paraffin and reduces the viscosity of crude oil could have many useful applications within the petroleum industry. Recent studies showed that magnetic fields reduce the Wax Appearance Temperature (WAT) and the viscosity of paraffin-based crude oil. For better understanding of this discovery, a series of tests was performed. This paper will show the influence of a DC magnetic field on rheological proprieties of three crude oils with different paraffin concentrations: a crude oil sample with 11 % p/p of paraffin concentration (sample 1); a crude oil sample with 6 % p/p of paraffin concentration (sample 2); a mixture of paraffin plus light crude oil with a total of 11 % p/p of paraffin concentration. These samples were placed in an electromagnet that generates a magnetic field of 1.3 Tesla. The samples' temperatures were conditioned around their Wax Appearance Temperature (WAT), and they were exposed to the field. As the viscosity of crude oil is very sensitive to the changes in temperature, it was ensured that the temperature has remained constant throughout the process. The sample 1 revealed a considerable reduction of viscosity: its original viscosity was 66 cP before magnetic field exposure, after that its viscosity was reduced to 39 cP. The other samples showed the same viscosity, before and after the magnetic field exposure. Since the samples 1 and 3 have the same paraffin concentrations, the viscosity reduction is not due only to the presence of paraffin; there must be other factors responsible for the interaction of sample 1 with the

Procedures for extraction and purification of leaf wax biomarkers from peats

Directory of Open Access Journals (Sweden)

J.E. Nichols

2011-12-01

Full Text Available Palaeoecological and palaeoclimate reconstruction, using leaf wax biomarkers, is a relatively new sub-discipline of peatland science. The ability to process large numbers of samples rapidly for biomarkers makes this type of analysis particularly appealing. This review is a guide to the preparation of leaf waxes for analysis by gas chromatography. The main phases of preparation are extraction of soluble organic compounds from sediment, separation of the total extract into fractions of differing polarity, and the derivatisation of polar functional groups. The procedures described here are not meant be exhaustive of all organic geochemical possibilities in peatlands, but a distillation of methods for the preparation of leaf waxes that are commonly and increasingly being used in palaeoecological and palaeoclimatological studies.

Radiotherapic Valuation of Paraffin Wax for Patients with Oral Cancer

Energy Technology Data Exchange (ETDEWEB)

Na, Kyung Su; Seo, Seuk Jin; Lee, Je Hee; Yoo, Sook Heun [Dept. of Radiation Oncology, Seoul National University Hosdital, Seoul (Korea, Republic of)

2011-03-15

This study is designed to investigate radiotherapic valuation of Paraffin Wax, which is newly formed for this study and generally utilized in dentistry, and Mouth Piece and Putty impression, which are commonly used in radiotherapy, for oral cavity as a compensator. Each compensator was formed by 10 x 10 x 1 cm and measured radiation dose attenuation ratio with reference of water phantom which is made of tissue-equivalent materials. Two patients with oral cancer underwent DRR (Digitally Reconstructed Radiogrph) of Offline Review Program of Aria System and Portal vision for 5 times for each material to evaluate reproducibility by each filling materials. Moreover, MU (monitor unit) changes by dose absorption were considered in the case of inevitable implication of an filling materials in the range for radiotherapy. Radiation dose attenuation ratios were shown -0.7{approx}+3.7% for Mouth Piece, +0.21{approx}+0.39% for Paraffin Wax and -2.71{approx}-1.76% for Putty impression. Error ranges of reproducibility of positions were measured {+-}3 mm for Mouth Piece, {+-}2 mm for Paraffin Wax and {+-}2 mm for Putty impression. Difference of prescription MU from dose absorption with an filling material increased +7.8% (250 MU) in Putty impression and -0.9% (230 MU) in Paraffin Wax as converted into a percentage from the standard phantom, Water 232 MU. Dose reduction of boundary between cavity and tissue was observed for Mouth Piece. Mouth Piece also had low reproducibility of positions as it had no reflection of anatomy of oral cavity even though it was a proper material to separate Maxilla and Mandible during therapy. On the other hand, Putty impression was a suitable material to correctly re-position oral cavity as before. However, it risked normal tissues getting unnecessary over irradiation and it caused radiation dose decrease by -2.5% for 1cm volume in comparison of it of water phantom. Dose reduction in Paraffin Wax, Fat Tissue-Equivalent Material, was smaller than other

Analysis of the Effect of Injection Pressure on Ignition Delay and Combustion Process of Biodiesel from Palm Oil, Algae and Waste Cooking Oil

Science.gov (United States)

Irham Anas, Mohd; Khalid, Amir; Hakim Zulkifli, Fathul; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin

2017-10-01

Biodiesel is a domestically produced, renewable fuel that can be manufactured from vegetable oils, animal fats, or recycled restaurant grease for use in diesel engines. The objective of this research is investigation the effects of the variant injection pressure on ignition delay and emission for different biodiesel using rapid compression machine. Rapid Compression Machine (RCM) is used to simulate a single compression stroke of an internal combustion engine as a real engine. Four types of biodiesel which are waste cooking oil, crude palm oil, algae and jatropha were tested at injection pressure of 80 MPa, 90 MPa and 130 MPa under constant ambient temperature at 950 K. Increased in injection pressure resulted shorter ignition delay proven by WCO5 which decreased from 1.3 ms at 80 MPa to 0.7 ms at 130 MPa. Meanwhile, emission for CO2 increased due to better fuel atomization for fuel-air mixture formation lead to completed combustion.

[Comparative adaptation of crowns of selective laser melting and wax-lost-casting method].

Science.gov (United States)

Li, Guo-qiang; Shen, Qing-yi; Gao, Jian-hua; Wu, Xue-ying; Chen, Li; Dai, Wen-an

2012-07-01

To investigate the marginal adaptation of crowns fabricated by selective laser melting (SLM) and wax-lost-casting method, so as to provide an experimental basis for clinic. Co-Cr alloy full crown were fabricated by SLM and wax-lost-casting for 24 samples in each group. All crowns were cemented with zinc phosphate cement and cut along longitudinal axis by line cutting machine. The gap between crown tissue surface and die was measured by 6-point measuring method with scanning electron microscope (SEM). The marginal adaptation of crowns fabricated by SLM and wax-lost-casting were compared statistically. The gap between SLM crowns were (36.51 ± 2.94), (49.36 ± 3.31), (56.48 ± 3.35), (42.20 ± 3.60) µm, and wax-lost-casting crowns were (68.86 ± 5.41), (58.86 ± 6.10), (70.62 ± 5.79), (69.90 ± 6.00) µm. There were significant difference between two groups (P casting method and SLM method provide acceptable marginal adaptation in clinic, and the marginal adaptation of SLM is better than that of wax-lost-casting method.

Efficient production of biodiesel from waste grease: one-pot esterification and transesterification with tandem lipases.

Science.gov (United States)

Yan, Jinyong; Li, Aitao; Xu, Yi; Ngo, Thao P N; Phua, Szechao; Li, Zhi

2012-11-01

A novel concept and efficient method for producing biodiesel (FAME) from grease (15-40wt% free fatty acid, FFA) were developed by using tandem lipases for one-pot esterification of FFA and transesterification of triglyceride with methanol in a solvent-free system. Combining immobilized Candida antarctica lipase B (CALB) (Novozyme 435) favoring the esterification and immobilized Thermomyces lanuginosus lipase (TLL) (Lipozyme TLIM) preferring the transesterification at 2:8 (wt/wt) gave FAME in 80% yield, being better than that with Novozyme 435 or Lipozyme TLIM. Recombinant Escherichia coli (Calb/Tll) co-expressing CALB and TLL was engineered as a more efficient tandem-lipases system. Using wet or dry cells (4wt%) gave FAME in 87% or 95% yield, which is much better than that with E. coli cells expressing either CALB or TLL alone. Cells of E. coli (Calb/Tll) were recycled for five times and retained 75% productivity, thus being practical for producing biodiesel from grease. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of soil moisture management on the quality of wax apple | Lin ...

African Journals Online (AJOL)

Wax apple (Syzygium samarngense Merr.et Perry) was one of the economically planted fruits in Taiwan. This research was conducted to evaluate the effects of different soil moisture management on increasing wax apple quality. It was preceded at two different soil properties (shallow soil and alluvial soil) in Pingtung, ...

ETHNOECOLOGY AND ETHNOBOTANY OF THE PALM CARNAUBA WAX IN BRAZILIAN SEMI-ARID

Directory of Open Access Journals (Sweden)

Rodrigo Ferreira de Sousa

2015-12-01

Full Text Available The aim of this study was to investigate aspects of ethnoecological and ethnobotanical of carnauba wax (Copernicia prunifera (Miller H. E. Moore, Arecaceae in an extractive community of municipality of Ipanguaçu, Rio Grande do Norte state. We interviewed key informants, using the technique of inducing nonspecific, guided tour and direct observation to confirm the data. According to most residents of Pedro Ezequiel Araújo community, the area of carnauba wax in the region is natural. In the research ethnoecological, 73% of informants reported the occurrence of “a different kind of carnauba”, known as “white carnauba” phenotypically distinct from the “common carnauba wax” by presenting clear stipe, smaller fruits and absence of spines on the petiole, and is rare at the study site. Much of the informants observed phenological phases of carnauba wax, being consistent in stating that the species has fruits dispersed by bats. In ethnobotany, powder wax was cited by all as the most important product extracted from leaves of carnauba and the most used, followed by fruit, stem and root. Were still reported the division of work in the extraction of powder wax from the carnauba. The results of this research will contribute to knowledge of ethnobotanical and ethnoecological carnauba, supporting strategies for management and conservation of natural populations.

Isolation and recrystallization of epicuticular waxes from Sorbus and Cotoneaster leaves

OpenAIRE

Ganeva Tsveta; Stefanova Miroslava; Koleva Dimitrina; Ruiz Segundo Ríos

2015-01-01

Wax morphology and chemical composition are widely accepted to be important for the protective properties of the leaf’s surface and also valuable characteristics in plant systematics. The leaves of Sorbus domestica L. and Cotoneaster granatensis Boiss., species of two large genera with intricate taxonomy referred to subtribe Pyrinae, Rosaceae (formerly subfamily Maloideae), were studied by scanning electron microscope (SEM) and performing different methods of wax isola...

Wax solidification of drying agents containing tritiated water

International Nuclear Information System (INIS)

Mishikawa, M.; Kido, H.

1984-01-01

It is necessary to immobilize the tritium not to give any impact on the environmental biosphere because tritium may give profound effects in the metabolic pathway. One of the most probable methods of immobilizing tritium would be incorporation of tritiated water in solid forms. Any drying or dehydration technique would be effective in a tritium cleanup system for off-gas streams containing tritium or tritiated water. Commonly used drying agents such as activated alumina, silica gel, molecular sieves and calcium sulfate are of value for removal of water vapour from air or other gases. For long term tritium storage, however, these adsorptive materials should be enveloped to prevent contact with water or water vapour because the rate of leaching, evaporation or diffusion of tritium from these porous materials is so large. The beeswax solidification method of the packed bed of drying agents adsorbing tritiated water is developed in this study, where the wax solidification procedure is performed by pouring the melt of wax into the void space of the packed bed of the drying agents and successive gradual cooling. The observed values of diffusivity or permeability of tritium in the wax solidified materials are about one-thousandth of those obtained for the cement block. Effect of coating on the rate of leaching is also discussed

Radiological properties of a wax-gypsum compensator material

International Nuclear Information System (INIS)

Plessis, F.C.P. du; Willemse, C.A.

2005-01-01

In this paper the radiological properties of a compensator material consisting of wax and gypsum is presented. Effective attenuation coefficients (EACs) have been determined from transmission measurements with an ion chamber in a Perspex phantom. Measurements were made at 80 and 100 cm source-to-skin distance (SSD) for beam energies of 6, 8, and 15 MV, for field sizes ranging from narrow beam geometries up to 40x40 cm 2 , and at measurement depths of maximum dose build-up, 5 and 10 cm. A parametrization equation could be constructed to predict the EAC values within 4% uncertainty as a function of field size and depth of measurement. The EAC dependence on off-axis position was also quantified at each beam energy and SSD. It was found that the compensator material reduced the required thickness for compensation by 26% at 8 MV when compared to pure paraffin wax for a 10x10 cm 2 field. Relative surface ionization (RSI) measurements have been made to quantify the effect of scattered electrons from the wax-gypsum compensator. Results indicated that for 80 cm SSD the RSI would exceed 50% for fields larger than 15x15 cm 2 . At 100 cm SSD the RSI values were below 50% for all field sizes used

The use of paraffin wax in a new solar cooker with inner and outer reflectors

Directory of Open Access Journals (Sweden)

Arabacigil Bihter

2015-01-01

Full Text Available In this paper, the potential use and effectiveness of paraffin wax in a new solar cooker was experimentally investigated during daylight and late evening hours. For these experiments, a cooker having an inner reflecting surface was designed, constructed by filling paraffin wax and metal shavings. The side- and sub-surface temperatures of the paraffin wax in the cooker are measured in the summer months of June and July. The thermal efficiency of the cooker was tested on different conditions. The results show that the optimum angle of the outer reflector is 30°. Here, the peak temperature of the paraffin wax in the solar cooker was 83.4 °C. The average solar radiation reflected makes a contribution of 9.26% to the temperature of paraffin wax with the outer reflector. The solar cooker with the outer reflector angle of 30° receives also reflected radiation from the inner reflectors. Besides, the heating time is decreased to approximately 1 hour. The designed solar cooker can be effectively used with 30.3% daily thermal efficiency and paraffin wax due to the amount of energy stored.

Effect of spatial distribution of wax and PEG-isocyanate on the morphology and hydrophobicity of starch films.

Science.gov (United States)

Muscat, Delina; Adhikari, Raju; Tobin, Mark J; McKnight, Stafford; Wakeling, Lara; Adhikari, Benu

2014-10-13

This study proposes a novel method for improving surface hydrophobicity of glycerol plasticized high amylose (HAG) films. We used polyethylene glycol isocyanate (PEG-iso) crosslinker to link HAG and three natural waxes (beeswax, candelilla wax and carnauba wax) to produce HAG+wax+PEG-iso films. The spatial distributions of wax and PEG-iso across the thickness of these films were determined using Synchrotron-based Fourier transform infrared spectroscopy. The hydrophobicity and surface morphology of the films were determined using contact angle (CA) and scanning electron microscopic measurements, respectively. The distribution patterns of wax and the PEG-iso across the thickness of the film, and the nature of crystalline patterns formed on the surface of these films were found to be the key factors affecting surface hydrophobicity. The highest hydrophobicity (CA >90°) was created when the PEG-iso was primarily distributed in the interior of the films and a hierarchical circular pinnacle structure of solidified wax was formed on the surface. Copyright © 2014 Elsevier Ltd. All rights reserved.

Cuticular wax accumulation is associated with drought tolerance in wheat near-isogenic lines

Directory of Open Access Journals (Sweden)

Jianmin Song

2016-11-01

Full Text Available Previous studies have shown that wheat grain yield is seriously affected by drought stress, and leaf cuticular wax is reportedly associated with drought tolerance. However, most studies have focused on cuticular wax biosynthesis and model species. The effects of cuticular wax on wheat drought tolerance have rarely been studied. The aims of the current study were to study the effects of leaf cuticular wax on wheat grain yield under drought stress using the above-mentioned wheat NILs and to discuss the possible physiological mechanism of cuticular wax on high grain yield under drought stress. Compared to water-irrigated (WI conditions, the cuticular wax content (CWC in glaucous and non-glaucous NILs under drought-stress (DS conditions both increased; mean increase values were 151.1% and 114.4%, respectively, which was corroborated by scanning electronic microscopy images of large wax particles loaded on the surfaces of flag leaves. The average yield of glaucous NILs was higher than that of non-glaucous NILs under DS conditions in 2014 and 2015; mean values were 7368.37 kg·ha-1 and 7103.51 kg·ha-1. This suggested that glaucous NILs were more drought-tolerant than non-glaucous NILs (P = 0.05, which was supported by the findings of drought tolerance indices TOL and SSI in both years, the relatively high water potential and relative water content, and the low ELWL. Furthermore, the photosynthesis rate (Pn of glaucous and non-glaucous wheat NILs under DS conditions decreased by 7.5% and 9.8%, respectively; however, glaucous NILs still had higher mean values of Pn than those of non-glaucous NILs, which perhaps resulted in the higher yield of glaucous NILs. This could be explained by the fact that glaucous NILs had a smaller Fv/Fm reduction, a smaller PI reduction and a greater ABS/RC increase than non-glaucous NILs under DS conditions. This is the first report to show that wheat cuticular wax accumulation is associated with drought tolerance. Moreover

Levels of Petroleum Hydrocarbons and some Heavy Metals in ...

African Journals Online (AJOL)

Michael Horsfall

has outlets to the Atlantic Ocean. The river which supports major commercial ... acidification. Oils and solids or viscous grease present were separated from liquid samples by filtration. After extraction, the residue after solvent evaporation was weighed to determine the oil and grease content. Compounds volatilized at or ...

The effect of the environment on the structure, quantity and composition of spruce needle wax

International Nuclear Information System (INIS)

Guenthardt-Goerg, M.S.

1994-01-01

The tubular structure (10-nonacosanol), as formed in spring on the wax surface of new spruce needles (Picea abies (L.)Karst.), or as regenerated on previous-year needles, becomes gradually fused and flattened in relation to needle exposure, particularly wind and rain. Structural flattening does not necessarily imply changes in wax quantity, composition or lead to changes in needle transpiration or photosynthesis, and was approximately reproduced by bathing excised twigs in water (with pH having little effect). In 4-year-old plants of one clone planted out at a Swiss plateau and alpine sites, changes in wax structure were similar to those found in mature trees. No such changes were found in plants with O 3 , SO 2 , ambient air, charcoal-filtered air, or in plants grown outside the chambers but shielded from rain. Area-related needle wax quantity in mature trees differed between the two sites, but did not differ in young plants under different treatments (fumigation or planted out at the sites). Minor differences in wax composition, however, were found to be related to the ozone dose of the fumigation or the ambient ozone dose at the sites. In each needle wax sample, 68 compounds grouped into 12 constituent classes were quantified. The quantity of the individual substituent classes varied among wax samples from genetically different mature trees at the two sites in a tree-specific way. Variation of these quantities was not larger than among young cloned plants after different treatments. (orig.)

21 CFR 172.886 - Petroleum wax.

Science.gov (United States)

2010-04-01

... availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register... it is very hygroscopic and will react with some metal containers in the presence of air. Phosphoric... high enough to keep the wax melted. (Note: In preheating the sulfoxide-acid mixture, remove the stopper...

Chemical properties and oxidative stability of Arjan (Amygdalus reuteri) kernel oil as emerging edible oil.

Science.gov (United States)

Tavakoli, Javad; Emadi, Teymour; Hashemi, Seyed Mohammad Bagher; Mousavi Khaneghah, Amin; Munekata, Paulo Eduardo Sichetti; Lorenzo, Jose Manuel; Brnčić, Mladen; Barba, Francisco J

2018-05-01

The oxidative stability, as well as the chemical composition of Amygdalus reuteri kernel oil (ARKO), were evaluated and compared to those of Amygdalus scoparia kernel oil (ASKO) and extra virgin olive oil (EVOO) during and after holding in the oven (170 °C for 8 h). The oxidative stability analysis was carried out by measuring the changes in conjugated dienes, carbonyl and acid values as well as oil/oxidative stability index and their correlation with the antioxidant compounds (tocopherol, polyphenols, and sterol compounds). The oleic acid was determined as the predominant fatty acid of ARKO (65.5%). Calculated oxidizability value and an iodine value of ARKO, ASKO and EVOO were reported as 3.29 and 3.24, 2.00 and 100.0, 101.4 and 81.9, respectively. Due to the high wax content (4.5% and 3.3%, respectively), the saponification number of ARKO and ASKO (96.4 and 99.8, respectively) was lower than that of EVOO (169.7). ARKO had the highest oxidative stability, followed by ASKO and EVOO. Therefore, ARKO can be introduced as a new source of edible oil with high oxidative stability. Copyright © 2018. Published by Elsevier Ltd.

Mineral oils, tars. [British patent

Energy Technology Data Exchange (ETDEWEB)

O' Brien, A M; Handmarch, E

1933-08-11

Hydrocarbon materials such as mineral oils and tars from coal, shale, lignite, or peat are freed from phenols and like oxy-bodies by heating under pressure in a closed vessel to a temperature and for a time sufficient to effect reduction of the oxy-bodies, and then removing the water formed by the reaction. 350/sup 0/ to 400/sup 0/C. for 30 to 60 minutes is suitable. Any wax-like constituents are converted to liquids of lower viscosity and settling point. The product may be fractionated to give light oils and a residue of aviation Diesel fuel. In an example, oil from the low-temperature distillation of coal and having a tar acid content of 30 per cent is treated in a tubular converter at 380/sup 0/C. and 400 lb. per sq. in for 40 min., and the benzine toluol, and xylol distilled; the residue has a tar acid content of only 7.6 per cent.

Experimental determination of hydrogen content of oil extract from jatropha seeds

International Nuclear Information System (INIS)

Okunade, I.O.; Jonah, S.A.; Omede, M.O.

2010-01-01

The thermal neutron technique was used for the determination of hydrogen content of oil extract from Jatropha seeds. The experimental arrangement consists of a source holder, Am-Be neutron source embedded in paraffin wax and 3 He detector was used to measure reflection coefficient as a function of hydrogen content of various hydrocarbon materials used as calibration standards. The hydrogen content which is an important property of fuel oils was determined for jatropha oil and jatropha-synthetic diesel using their measured values of neutron reflection coefficients and calibration data. The result obtained showed that the hydrogen content of Jatropha oil exceeds that of the synthetic diesel, thus indicating its suitability as a fuel oil for powering diesel engines. The results obtained also indicated that hydrogen content of jatropha-synthetic diesel mixture increases as the volumetric concentration of jatropha oil in the mixture increases, indicating that jatropha oil can serve as a suitable additive to synthetic diesel oil.

Monitoring, characterization and comparison. Operation-project of oil and oil water systems in platforms

International Nuclear Information System (INIS)

P Junior, Oswaldo A.; Louvisse, Ana M.T.; Ramalho, Joao B.V.S.; Miragaya, Jose C.G.

2000-01-01

During the process of petroleum production, water are also commonly produced. Usually, a standard oil-water separation process will not lead to water phase ready to be discharged - the present legislation requires oily contents (oil and/or greases) bellow 20 mg/L concentration level value. Thus, secondary treatment is required to bring such oily concentration to the allowed level or lower, prior to the water discard in the environment. This paper describes the adopted systematic work in the Campos Basin Petroleum Production Platforms, which has allowed to evaluate and optimize the water treatment performed in there. Such description includes the typical water treatment systems installed, the typical physical-chemistry of the effluents and also presents comparisons between the basic designs that guided such systems construction and their present operational conditions and set-ups. The analysis of such results has allowed the introduction of minor modifications leading to the process optimization. The common use of Pilot Plants in such optimization process is also described and their contribution reported. (author)

Wax co-cracking synergism of high density polyethylene to alternative fuels

Directory of Open Access Journals (Sweden)

Magdy Motawie

2015-09-01

Full Text Available Attempts have been made to understand the thermal degradation of high density polyethylene (HDPE and their combined co-cracking using different ratios of HDPE and petroleum wax under nitrogen atmosphere. We have conducted the experiments using HDPE as the raw material and petroleum wax as co-feed by at 400 and 450 °C reaction temperatures. The product distribution was noted along with reaction time of 0.5–3 h for the degradation. Thermal gravimetric analysis (TGA technique was used to measure the weight change of the feedstock as a function of temperature and time. Differential scanning calorimetry (DSC was used to determine the degradation temperature. Products were characterized using gas chromatography (GC and infrared spectroscopy (FTIR, some other standard physical methods were used to determine the main properties of the liquid products. Results show that the mixed plastic-wax samples could be converted into gases, gasoline, and middle distillate depending upon the composition of feed polymer/wax ratio. It was found that the products mostly consisted of paraffin and olefin compounds, with carbon numbers of C1–C4, C5–C9 and C10–C19 in the case of gases, gasoline and middle distillate respectively.

Study on influence of flow rates on voids in waxy crude oil subjected to dynamic and static cooling

Directory of Open Access Journals (Sweden)

Girma T. Chala

2015-12-01

Full Text Available The assumption of constant yield stress in the conventional restart pressure equation neglects the effects of thermal shrinkage and gas voids formation, which in turn resulted in an over-designed production piping systems. This paper presents a study on the effects of flow rates on the formation of voids in gelled waxy crude oil. A flow loop rig simulating offshore waxy crude oil transportation was used to produce a gel. A Magnetic Resonance Imaging (MRI was used to scan the gelled crude oil over the three planes. Waxy crude oil underwent both dynamic and static cooling to observe the effects of volume flow rates on the voids formed in wax-oil gel. Volume flow rate was found to have different influences on the intra-gel voids in the pipeline. A volume flow rate of 5 L/min resulted in a maximum total voids volume of 6.98% while 20 L/min produced a minimum total voids volume of 5.67% in the entire pipe. Slow flow rates resulted in a larger voids volume near the pipe wall. In contrast, faster flow rates produced insignificantly higher voids volume around pipe core. Generally, slower flow rates favoured the formation of higher total voids volume following sufficient steady time of wax crystal formation, producing larger voids areas in gelled waxy crude oil.

Radiotherapic Valuation of Paraffin Wax for Patients with Oral Cancer

International Nuclear Information System (INIS)

Na, Kyung Su; Seo, Seuk Jin; Lee, Je Hee; Yoo, Sook Heun

2011-01-01

This study is designed to investigate radiotherapic valuation of Paraffin Wax, which is newly formed for this study and generally utilized in dentistry, and Mouth Piece and Putty impression, which are commonly used in radiotherapy, for oral cavity as a compensator. Each compensator was formed by 10 x 10 x 1 cm and measured radiation dose attenuation ratio with reference of water phantom which is made of tissue-equivalent materials. Two patients with oral cancer underwent DRR (Digitally Reconstructed Radiogrph) of Offline Review Program of Aria System and Portal vision for 5 times for each material to evaluate reproducibility by each filling materials. Moreover, MU (monitor unit) changes by dose absorption were considered in the case of inevitable implication of an filling materials in the range for radiotherapy. Radiation dose attenuation ratios were shown -0.7∼+3.7% for Mouth Piece, +0.21∼+0.39% for Paraffin Wax and -2.71∼-1.76% for Putty impression. Error ranges of reproducibility of positions were measured ±3 mm for Mouth Piece, ±2 mm for Paraffin Wax and ±2 mm for Putty impression. Difference of prescription MU from dose absorption with an filling material increased +7.8% (250 MU) in Putty impression and -0.9% (230 MU) in Paraffin Wax as converted into a percentage from the standard phantom, Water 232 MU. Dose reduction of boundary between cavity and tissue was observed for Mouth Piece. Mouth Piece also had low reproducibility of positions as it had no reflection of anatomy of oral cavity even though it was a proper material to separate Maxilla and Mandible during therapy. On the other hand, Putty impression was a suitable material to correctly re-position oral cavity as before. However, it risked normal tissues getting unnecessary over irradiation and it caused radiation dose decrease by -2.5% for 1cm volume in comparison of it of water phantom. Dose reduction in Paraffin Wax, Fat Tissue-Equivalent Material, was smaller than other impressions and

Combined hydrogen and carbon isotopes of plant waxes as an indicator of drought impacts on ancient Maya agriculture

Science.gov (United States)

Douglas, P. M.; Pagani, M.; Eglinton, T. I.; Brenner, M.; Hodell, D. A.; Curtis, J. H.

2012-12-01

There is increasing evidence suggesting that a series of droughts in the Yucatan Peninsula coincided with the Terminal Classic decline of the Classic Maya civilization (ca. 1250 to 1000 years BP). However, there is little evidence directly linking climatic change and changes in human activities in this region. In this study we combine plant-wax δD, δ13C, and Δ14C analyses in two lake sediment cores from southeastern Mexico and northern Guatemala to develop coupled records of hydroclimate variability and human-driven vegetation change. Plant-wax specific Δ14C ages indicate a large input of pre-aged plant waxes into lake sediment. Comparison of plant-wax δD records with other regional hydroclimate proxy records suggest that plant-wax ages are evenly distributed around plant-wax radiocarbon ages, and that applying an age model based on plant-wax radiocarbon ages is appropriate for these lake sediments. We evaluate how differences in plant-wax age distributions influence stable isotope records to assess the age uncertainty associated with records of climate and vegetation change derived from plant-wax stable isotopes. In this low-elevation tropical environment plant-wax δ13C is largely controlled by the relative abundance of C3 and C4 plants. The ancient Maya practiced widespread maize (C4) agriculture and strongly influenced regional C3-C4 vegetation dynamics. Under natural conditions C4 plant coverage and plant-wax δ13C would tend to co-vary positively since C4 plants are well adapted for dry conditions. Under ancient Maya land-use, however, this relationship is likely to be decoupled, since drought would have disrupted C4 agriculture. Combined analysis of plant-wax δD and δ13C from both lakes indicates increasingly divergent trends following ca. 3500 years BP, around the onset of widespread ancient Maya agriculture. After this time high plant-wax δD values tend to correspond with low plant-wax δ13C values and vice versa. This pattern is consistent with

Development and properties of a wax ester hydrolase in the cotyledons of jojoba seedlings.

Science.gov (United States)

Huang, A H; Moreau, R A; Liu, K D

1978-03-01

The activity of a wax ester hydrolase in the cotyledons of jojoba (Simmondsia chinensis) seedlings increased drastically during germination, parallel to the development of the gluconeogenic process. The enzyme at its peak of development was obtained in association with the wax body membrane, and its properties were studied. It had an optimal activity at alkaline pH (8.5-9). The apparent K(m) value for N-methylindoxylmyristate was 93 muM. It was stable at 40 C for 30 min but was inactivated at higher temperature. Various divalent cations and ethylenediaminetetraacetate had little effect on the activity. p-Chloromercuribenzoate was a strong inhibitor of the enzyme activity, and its effect was reversed by subsequent addition of dithiothreitol. It had a broad substrate specificity with highest activities on monoglycerides, wax esters, and the native substrate (jojoba wax).

76 FR 773 - Petroleum Wax Candles From the People's Republic of China: Continuation of Antidumping Duty Order

Science.gov (United States)

2011-01-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-504] Petroleum Wax Candles From... Trade Commission (``ITC'') that revocation of the antidumping duty order on petroleum wax candles from... order on petroleum wax candles from the PRC pursuant to section 751(c)(2) of the Tariff Act of 1930, as...

Greasing the Wheels of Trade: measuring the Dutch transaction with occupational data

OpenAIRE

Dalen, Hendrik; Vuuren, Aico

2003-01-01

textabstractHow much does a nation spend on resources to 'grease the wheels of trade'? To examine this question the Dutch economy is used as an exemplary case as the Netherlands are known as a nation of traders. This image was derived in the seventeenth century from successes in long distance trade, shipping and financial innovations. Despite its historical background in trading the potential to 'truck and barter' has never been adequately measured. In this paper we present a first attempt in...

Influence of Brazilian vegetable oils on mechanical resistence of hair fiber

Directory of Open Access Journals (Sweden)

Maria Valéria Velasco

2015-02-01

Full Text Available Associating the global trend of incorporating active compounds and plants in cosmetic formulations and the vast Brazilian biodiversity, the present work aimed to study the incorporation of Brazilian vegetable oils in hair conditioner formulations, evaluating the mechanical resistance of hair fibers. The following oils were incorporated into base formulations at 5.0 % (w/w: babassu, buriti, andiroba and pequi. The formulations were applied to samples of Caucasian hair, followed by several washing steps, then the evaluation of mechanical strength. It was found that there was no statistically significant difference in mechanical resistance between samples treated with oils and the control between the first and seventh wash cycles. This fact can be explained by the possible low penetration of oils into the cortex, a region responsible for the mechanical properties of the hair fiber, since the grease composition disfavors its diffusion. The common effects of vegetable oils on the cuticle, such as filling in cracks or cavities, lubrication, and increased protein hydrophobicity cannot be excluded. The oils tested in this work were not able to raise or protect hair tresses. However, additional studies are required in order to establish the effects of oil treatments, particularly in damaged hair.

Solar Alpha Rotary Joint (SARJ) Lubrication Interval Test and Evaluation (LITE). Post-Test Grease Analysis

Science.gov (United States)

Golden, Johnny L.; Martinez, James E.; Devivar, Rodrigo V.

2015-01-01

The Solar Alpha Rotary Joint (SARJ) is a mechanism of the International Space Station (ISS) that orients the solar power generating arrays toward the sun as the ISS orbits our planet. The orientation with the sun must be maintained to fully charge the ISS batteries and maintain all the other ISS electrical systems operating properly. In 2007, just a few months after full deployment, the starboard SARJ developed anomalies that warranted a full investigation including ISS Extravehicular Activity (EVA). The EVA uncovered unexpected debris that was due to degradation of a nitride layer on the SARJ bearing race. ISS personnel identified the failure root-cause and applied an aerospace grease to lubricate the area associated with the anomaly. The corrective action allowed the starboard SARJ to continue operating within the specified engineering parameters. The SARJ LITE (Lubrication Interval Test and Evaluation) program was initiated by NASA, Lockheed Martin, and Boeing to simulate the operation of the ISS SARJ for an extended time. The hardware was designed to test and evaluate the exact material components used aboard the ISS SARJ, but in a controlled area where engineers could continuously monitor the performance. After running the SARJ LITE test for an equivalent of 36+ years of continuous use, the test was opened to evaluate the metallography and lubrication. We have sampled the SARJ LITE rollers and plate to fully assess the grease used for lubrication. Chemical and thermal analysis of these samples has generated information that has allowed us to assess the location, migration, and current condition of the grease. The collective information will be key toward understanding and circumventing any performance deviations involving the ISS SARJ in the years to come.

Improving the cooling performance of electrical distribution transformer using transformer oil – Based MEPCM suspension

Directory of Open Access Journals (Sweden)

Mushtaq Ismael Hasan

2017-04-01

Full Text Available In this paper the electrical distribution transformer has been studied numerically and the effect of outside temperature on its cooling performance has been investigated. The temperature range studied covers the hot climate regions. 250 KVA distribution transformer is chosen as a study model. A novel cooling fluid is proposed to improve the cooling performance of this transformer, transformer oil-based microencapsulated phase change materials suspension is used with volume concentration (5–25% as a cooling fluid instead of pure transformer oil. Paraffin wax is used as a phase change material to make the suspension, in addition to the ability of heat absorption due to melting, the paraffin wax considered as a good electrical insulator. Results obtained show that, using of MEPCM suspension instead of pure transformer oil lead to improve the cooling performance of transformer by reducing its temperature and as a consequence increasing its protection against the breakdown. The melting fraction increased with increasing outside temperature up to certain temperature after which the melting fraction reach maximum constant value (MF = 1 which indicate that, the choosing of PCM depend on the environment in which the transformer is used.

Development of lamellar structures in natural waxes - an electron diffraction investigation

Science.gov (United States)

Dorset, Douglas L.

1999-06-01

When they are recrystallized from the melt, natural plant or insect waxes tend to form solid phases with a nematic-like structure (i.e. a parallel array of polymethylene chains with little or no aggregation of the molecules into distinct layers). An electron diffraction study of carnauba wax and two types of beeswax has shown that the degree of molecular organization into lamellar structures can be enhanced by annealing in the presence of benzoic acid, which also acts as an epitaxial substrate. Nevertheless, the resultant layer structure in the annealed solid is not the same as that found for paraffin wax fractions refined from petroleum. Probably because of a small but significant fraction of a very long chain ingredient, the lamellar separation is incomplete, incorporating a number of `bridging molecules' that span the nascent lamellar interface.The same phenomenon has been described recently for a low molecular weight polyethylene.

Compound-Specific Radiocarbon Dating Reveals the Age Distribution of Plant-Wax Biomarkers Exported to the Bengal Fan

Science.gov (United States)

Galy, V.; French, K. L.; Hein, C. J.; Haghipour, N.; Wacker, L.; Kudrass, H.; Eglinton, T. I.

2017-12-01

The stable isotope composition of leaf-wax compounds preserved in lacustrine and marine sediments has been widely used to reconstruct terrestrial paleo-environments. However, the timescales of plant-wax storage in continental reservoirs before riverine export are not well known, representing a key uncertainty in paleo-environment studies. We couple numerical models with bulk and leaf-wax fatty acid organic 13C and 14C signatures hosted in a high-deposition-rate sediment core from the Bengal shelf canyon in order to estimate storage timescales within the Ganges-Brahmaputra catchment area. The fatty acid 14C record reveals a muted nuclear weapons bomb spike, requiring that the Ganges-Brahmaputra river system exports a mixture of young and old (pre-aged) leaf-wax compounds. According to numerical simulations, 79-83% of the leaf-wax fatty acids in this core are sourced from continental reservoirs that store organic carbon on an average of 1000-1200 calendar years, while the remainder has an average age of 15 years. These results demonstrate that a majority of the leaf-wax compounds produced in the Ganges-Brahmaputra river basin was stored in soils, floodplains, and wetlands prior to its export to the Bengal Fan. We will discuss the implications of these findings for plant-wax based paleoenvironmental records.

Geometrical effects of conventional and digital prosthodontic planning wax-ups on lateral occlusal contact number, contact area, and steepness.

Science.gov (United States)

Abduo, Jaafar

2017-01-01

This study evaluated and compared the effect of conventional and digital wax-ups on three lateral occlusion variables: contact number, contact area, and steepness. Dental casts of 10 patients with Angle Class I relationship were included in the study. All patients required fixed prosthodontic treatment that would affect lateral occlusion. The casts of all patients received conventional and digital wax-ups. For pretreatment, conventional wax-up, and digital wax-up casts, contact number, contact area, and occlusion steepness were measured at four lateral positions, that is, at excursions of 0.5, 1.0, 2.0, and 3.0 mm from maximal intercuspation. Lateral occlusion scheme variables were affected by use of diagnostic wax-ups. For all types of casts, contact number decreased as excursion increased. The two types of wax-ups had similar contact number patterns, and contact number was significantly greater for these casts than for pretreatment casts in the earlier stages of excursion. Similarly, contact area gradually decreased with increasing excursion in the pretreatment and conventional and digital wax-up casts. There was only a minimal decrease in occlusion steepness as excursion increased. However, lateral occlusion was generally steeper for digital wax-up casts.

Thermophilic anaerobic co-digestion of sewage sludge with grease waste: Effect of long chain fatty acids in the methane yield and its dewatering properties

International Nuclear Information System (INIS)

Silvestre, G.; Illa, J.; Fernández, B.; Bonmatí, A.

2014-01-01

Highlights: • Thermophilic anaerobic codigestion of sewage sludge and grease waste (GW) doubles methane yield. • High GW doses in the influent leads to instability and LCFA accumulation in the effluent. • GW addition promotes acetoclastic activity whilst worsening the hydrogenothrophic activity. • The mesophilic codigestion with GW performs better than the thermophilic one. - Abstract: Thermophilic co-digestion of sewage sludge with three different doses of trapped grease waste (GW) from the pre-treatment of a WWTP has been assessed in a CSTR bench-scale reactor. After adding 12% and 27% of grease waste (on COD basis), the organic loading rate increased from 2.2 to 2.3 and 2.8 kg COD m −3 d −1 respectively, and the methane yield increased 1.2 and 2.2 times. Further GW increase (37% on COD basis) resulted in an unstable methane yield and in long chain fatty acids (LCFA) accumulation. Although this inestability, the presence of volatile fatty acids in the effluent was negligible, showing good adaptation to fats of the thermophilic biomass. Nevertheless, the presence of LCFA in the effluent worsens its dewatering properties. Specific methanogenic activity tests showed that the addition of grease waste ameliorates the acetoclastic activity in detriment of the hydrogenotrophic activity, and suggests that the tolerance to LCFA can be further enhanced by slowly increasing the addition of lipid-rich materials

Effects of mesquite gum-candelilla wax based edible coatings on the quality of guava fruit (Psidium guajava L.)

Science.gov (United States)

Tomás, S. A.; Bosquez-Molina, E.; Stolik, S.; Sánchez, F.

2005-06-01

The ability of composite edible coatings to preserve the quality of guava fruit (Psidium guajava L.) at 20ºC was studied for a period of 15 days. The edible coatings were formulated with candelilla wax blended with white mineral oil as the lipid phase and mesquite gum as the structural material. The use of edible coatings prolonged the shelf life of treated fruits by retarding ethylene emission and enhancing texture as compared to control samples. At the sixth day, the ethylene produced by the control samples was fivefold higher than the ethylene produced by the coated samples. In addition, the physiological weight loss of coated fruits was nearly 30% lower than the control samples.

78 FR 14457 - Guidelines Establishing Test Procedures for the Analysis of Pollutants Under the Clean Water Act...

Science.gov (United States)

2013-03-06

... discharge limits. Method 1664A is a liquid/liquid extraction (LLE), gravimetric procedure that employs...: EPA discussed, but did not propose, a new method, ASTM D7575, for oil and grease in the 2010 proposed Methods Update Rule (MUR). Oil and grease is a method-defined parameter. That is, the nature and amount of...

Clustering of comb and propolis waxes based on the distribution of aliphatic constituents

Directory of Open Access Journals (Sweden)

Custodio Angela R.

2003-01-01

Full Text Available Chemical composition data for 41 samples of propolis waxes and 9 samples of comb waxes of Apis mellifera collected mainly in Brazil were treated using Principal Component Analysis (PCA and Hierarchical Cluster Analysis (HCA. For chemometrical analysis, the distribution of hydrocarbons and residues of alcohols and carboxylic acids of monoesters were considered. The clustering obtained revealed chemical affinities and differences not previously grasped by simple eye-inspection of the data. No consistent differences were detected between comb and propolis waxes. These and previous results suggest that hydrocarbons, carboxylic acids, aliphatic alcohols and esters from both comb and propolis waxes are bee-produced compounds and, hence, the differences detected between one and another region are dependent on genetic factors related to the insects rather than the local flora. The samples analyzed were split into two main clusters, one of them comprising exclusively material collected in the State of São Paulo. The results are discussed with respect to the africanization of honeybees that first took place in that State and therefrom irradiated to other parts of Brazil.

Friction, Wear, and Evaporation Rates of Various Materials in Vacuum to 10(exp -7) mm Hg

Science.gov (United States)

Buckley, Donald H.; Swikert, Max; Johnson, Robert L.

1961-01-01

The requirements for bearings and seals to operate in the environment of space dictate a new area for lubrication research. The low ambient pressures encountered in space can be expected to influence the behavior of oil, grease, and solid-film lubricants. The property of these materials most significantly affected by low ambient pressures is the evaporation rate. Various investigators have therefore measured the evaporation rates of oils and greases in vacuum as one method of establishing their relative merit for space applications (1-3). The results of this work have given some indication as to the oils and greases with the greatest stability at reduced ambient pressures. Only limited experimental work, however, has been reported in the literature for inorganic solids and soft metals which have potential use as solid lubricant films or coatings for hard alloy substrates [e.g. Reference ( 4 )]. In general, the evaporation rates of these materials would be lower than those of oils and greases. These films might therefore be very attractive as lubricants for high vacuum service.

Development of high performance lubricant through the compatibility of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene; Graxa de poliureia: estudo da compatibilidade da poliureia, polialfaolefina e politetrafluoretileno irradiado para melhoria da lubricidade e estabilidade

Energy Technology Data Exchange (ETDEWEB)

Ratao, Natalia Torres

2013-07-01

Lubricants are gaseous, liquid, semi solid or solid (powder) materials those form a film between two parties preventing friction. High performance lubricants are designed to work under severe conditions of temperature, pressure, and contamination. The most used are liquids (oils) and semi solids (greases). Greases are applied where oils can drain or in inaccessible places and are divided generally into two classes, soap and no soap. The most used non soap grease is polyurea, obtained by the reaction between amine and isocyanate, has highly thixotropic, high dielectric strength and excellent anticorrosive property, so it is widely used for lubrication of electric motors and shipbuilding machinery. For a grease with high performance, in this study was used a synthetic lubricant fluid, polyalphaolefin, and was also employed solid lubricant additive polytetrafluoroethylene (PTFE) due its lowest coefficient of friction, is found commercially irradiated in air to obtain smaller particles and to produce oxygenated terminal groups those are more compatible with the metal surface. The tests conducted were comparatively between pure polyurea grease and with PTFE additive. The characterizations were made by infrared spectroscopy and elemental analysis of C, N and H and Free NCO index, proving the formation of four carbons polyurea (tetraurea). The functional analysis of drop point and oil separation showed high stability and compatibility between the polymers increased when PTFE was added. The excellent resistance of pure tetraurea grease to wear and extreme pressure were demonstrated by four-ball and practical bearings tests, characterizing this grease as a high performance lubricant, when compared to most used greases in the market. (author)

Development of high performance lubricant through the compatibility of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene

International Nuclear Information System (INIS)

Ratao, Natalia Torres

2013-01-01

Lubricants are gaseous, liquid, semi solid or solid (powder) materials those form a film between two parties preventing friction. High performance lubricants are designed to work under severe conditions of temperature, pressure, and contamination. The most used are liquids (oils) and semi solids (greases). Greases are applied where oils can drain or in inaccessible places and are divided generally into two classes, soap and no soap. The most used non soap grease is polyurea, obtained by the reaction between amine and isocyanate, has highly thixotropic, high dielectric strength and excellent anticorrosive property, so it is widely used for lubrication of electric motors and shipbuilding machinery. For a grease with high performance, in this study was used a synthetic lubricant fluid, polyalphaolefin, and was also employed solid lubricant additive polytetrafluoroethylene (PTFE) due its lowest coefficient of friction, is found commercially irradiated in air to obtain smaller particles and to produce oxygenated terminal groups those are more compatible with the metal surface. The tests conducted were comparatively between pure polyurea grease and with PTFE additive. The characterizations were made by infrared spectroscopy and elemental analysis of C, N and H and Free NCO index, proving the formation of four carbons polyurea (tetraurea). The functional analysis of drop point and oil separation showed high stability and compatibility between the polymers increased when PTFE was added. The excellent resistance of pure tetraurea grease to wear and extreme pressure were demonstrated by four-ball and practical bearings tests, characterizing this grease as a high performance lubricant, when compared to most used greases in the market. (author)

Retained bone wax on CT at one year after dacryocystorhinostomy: A case report

International Nuclear Information System (INIS)

Kim, Seung Hyun; Park, Dong Woo; Jeong, Jin Yeok; Lee, Jong Ah; Lee, Young Jun

2015-01-01

A 71-year-old man with chronic rhinosinusitis presented with a purulent, foul-smelling nasal discharge and obstruction. One year earlier he had been treated with a dacryocystorhinostomy for nasolacrimal duct obstruction. During the procedure, bone wax had been used to control bleeding in the anterior upper nasal cavity. On computed tomographic imaging, a fat-density lesion was seen in the anterior upper sinonasal cavity and was found to be hypointense or signal-void on all magnetic resonance imaging sequences. The lesion, which proved to consist of bone wax, was surgically removed. Here, we present the imaging features of retained bone wax in a patient with clinically diagnosed chronic rhinosinusitis after dacryocystorhinostomy

Retained bone wax on CT at one year after dacryocystorhinostomy: A case report

Energy Technology Data Exchange (ETDEWEB)

Kim, Seung Hyun; Park, Dong Woo; Jeong, Jin Yeok [Guri Hospital, Hanyang University College of Medicine, Guri (Korea, Republic of); Lee, Jong Ah; Lee, Young Jun [Dept. of Radiology, Seoul Hospital, Hanyang University College of Medicine, Seoul (Korea, Republic of)

2015-09-15

A 71-year-old man with chronic rhinosinusitis presented with a purulent, foul-smelling nasal discharge and obstruction. One year earlier he had been treated with a dacryocystorhinostomy for nasolacrimal duct obstruction. During the procedure, bone wax had been used to control bleeding in the anterior upper nasal cavity. On computed tomographic imaging, a fat-density lesion was seen in the anterior upper sinonasal cavity and was found to be hypointense or signal-void on all magnetic resonance imaging sequences. The lesion, which proved to consist of bone wax, was surgically removed. Here, we present the imaging features of retained bone wax in a patient with clinically diagnosed chronic rhinosinusitis after dacryocystorhinostomy.

Natural Organochlorines as Precursors of 3-Monochloropropanediol Esters in Vegetable Oils.

Science.gov (United States)

Tiong, Soon Huat; Saparin, Norliza; Teh, Huey Fang; Ng, Theresa Lee Mei; Md Zain, Mohd Zairey Bin; Neoh, Bee Keat; Md Noor, Ahmadilfitri; Tan, Chin Ping; Lai, Oi Ming; Appleton, David Ross

2018-01-31

During high-temperature refining of vegetable oils, 3-monochloropropanediol (3-MCPD) esters, possible carcinogens, are formed from acylglycerol in the presence of a chlorine source. To investigate organochlorine compounds in vegetable oils as possible precursors for 3-MCPD esters, we tested crude palm, soybean, rapeseed, sunflower, corn, coconut, and olive oils for the presence of organochlorine compounds. Having found them in all vegetable oils tested, we focused subsequent study on oil palm products. Analysis of the chlorine isotope mass pattern exhibited in high-resolution mass spectrometry enabled organochlorine compound identification in crude palm oils as constituents of wax esters, fatty acid, diacylglycerols, and sphingolipids, which are produced endogenously in oil palm mesocarp throughout ripening. Analysis of thermal decomposition and changes during refining suggested that these naturally present organochlorine compounds in palm oils and perhaps in other vegetable oils are precursors of 3-MCPD esters. Enrichment and dose-response showed a linear relationship to 3-MCPD ester formation and indicated that the sphingolipid-based organochlorine compounds are the most active precursors of 3-MCPD esters.

A review of the performance and structural considerations of paraffin wax hybrid rocket fuels with additives

Science.gov (United States)

Veale, Kirsty; Adali, Sarp; Pitot, Jean; Brooks, Michael

2017-12-01

Paraffin wax as a hybrid rocket fuel has not been comprehensively characterised, especially regarding the structural feasibility of the material in launch applications. Preliminary structural testing has shown paraffin wax to be a brittle, low strength material, and at risk of failure under launch loading conditions. Structural enhancing additives have been identified, but their effect on motor performance has not always been considered, nor has any standard method of testing been identified between research institutes. A review of existing regression rate measurement techniques on paraffin wax based fuels and the results obtained with various additives are collated and discussed in this paper. The review includes 2D slab motors that enable visualisation of liquefying fuel droplet entrainment and the effect of an increased viscosity on the droplet entrainment mechanism, which can occur with the addition of structural enhancing polymers. An increased viscosity has been shown to reduce the regression rate of liquefying fuels. Viscosity increasing additives that have been tested include EVA and LDPE. Both these additives increase the structural properties of paraffin wax, where the elongation and UTS are improved. Other additives, such as metal hydrides, aluminium and boron generally offer improvements on the regression rate. However, very little consideration has been given to the structural effects these additives have on the wax grain. A 40% aluminised grain, for example, offers a slight increase in the UTS but reduces the elongation of paraffin wax. Geometrically accurate lab-scale motors have also been used to determine the regression rate properties of various additives in paraffin wax. A concise review of all available regression rate testing techniques and results on paraffin wax based hybrid propellants, as well as existing structural testing data, is presented in this paper.

Review of inservice inspections of greased tendons in prestressed-concrete containments

International Nuclear Information System (INIS)

Dougan, J.R.; Ashar, H.

1983-01-01

Prestressed-concrete containments in the United States using greased prestressing tendons are inspected periodically to ensure structural integrity and to identify and correct problem areas before they become critical. An analysis of the available utility inspection data and an evaluation of the current and proposed guidelines were conducted to provide a measure of the reliability of the inspection process. Comments from utility and industry personnel were factored into the analysis. The results indicated that the majority of the few incidences of problems or abnormalities which occurred were minor in nature and did not threaten the structural integrity of the containment

Understanding nucleic acid structural changes by comparing wide-angle x-ray scattering (WAXS) experiments to molecular dynamics simulations

Energy Technology Data Exchange (ETDEWEB)

Pabit, Suzette A.; Katz, Andrea M.; Pollack, Lois [School of Applied and Engineering Physics, Cornell University, Ithaca, New York 14853 (United States); Tolokh, Igor S. [Department of Computer Science, Virginia Tech, Blacksburg, Virginia 24061 (United States); Drozdetski, Aleksander [Department of Physics, Virginia Tech, Blacksburg, Virginia 24061 (United States); Baker, Nathan [Pacific Northwest National Laboratory, Richland, Washington 99352 (United States); Onufriev, Alexey V. [Department of Computer Science, Virginia Tech, Blacksburg, Virginia 24061 (United States); Department of Physics, Virginia Tech, Blacksburg, Virginia 24061 (United States)

2016-05-28

Wide-angle x-ray scattering (WAXS) is emerging as a powerful tool for increasing the resolution of solution structure measurements of biomolecules. Compared to its better known complement, small angle x-ray scattering (SAXS), WAXS targets higher scattering angles and can enhance structural studies of molecules by accessing finer details of solution structures. Although the extension from SAXS to WAXS is easy to implement experimentally, the computational tools required to fully harness the power of WAXS are still under development. Currently, WAXS is employed to study structural changes and ligand binding in proteins; however, the methods are not as fully developed for nucleic acids. Here, we show how WAXS can qualitatively characterize nucleic acid structures as well as the small but significant structural changes driven by the addition of multivalent ions. We show the potential of WAXS to test all-atom molecular dynamics (MD) simulations and to provide insight into understanding how the trivalent ion cobalt(III) hexammine (CoHex) affects the structure of RNA and DNA helices. We find that MD simulations capture the RNA structural change that occurs due to addition of CoHex.

Modified paraffin wax for improvement of histological analysis efficiency.

Science.gov (United States)

Lim, Jin Ik; Lim, Kook-Jin; Choi, Jin-Young; Lee, Yong-Keun

2010-08-01

Paraffin wax is usually used as an embedding medium for histological analysis of natural tissue. However, it is not easy to obtain enough numbers of satisfactory sectioned slices because of the difference in mechanical properties between the paraffin and embedded tissue. We describe a modified paraffin wax that can improve the histological analysis efficiency of natural tissue, composed of paraffin and ethylene vinyl acetate (EVA) resin (0, 3, 5, and 10 wt %). Softening temperature of the paraffin/EVA media was similar to that of paraffin (50-60 degrees C). The paraffin/EVA media dissolved completely in xylene after 30 min at 50 degrees C. Physical properties such as the amount of load under the same compressive displacement, elastic recovery, and crystal intensity increased with increased EVA content. EVA medium (5 wt %) was regarded as an optimal composition, based on the sectioning efficiency measured by the numbers of unimpaired sectioned slices, amount of load under the same compressive displacement, and elastic recovery test. Based on the staining test of sectioned slices embedded in a 5 wt % EVA medium by hematoxylin and eosin (H&E), Masson trichrome (MT), and other staining tests, it was concluded that the modified paraffin wax can improve the histological analysis efficiency with various natural tissues. (c) 2010 Wiley-Liss, Inc.

Development of lamellar structures in natural waxes - an electron diffraction investigation

Energy Technology Data Exchange (ETDEWEB)

Dorset, Douglas L. [Electron Diffraction Department, Hauptman-Woodward Medical Research Institute, Inc., Buffalo, NY (United States)

1999-06-07

When they are recrystallized from the melt, natural plant or insect waxes tend to form solid phases with a nematic-like structure (i.e. a parallel array of polymethylene chains with little or no aggregation of the molecules into distinct layers). An electron diffraction study of carnauba wax and two types of beeswax has shown that the degree of molecular organization into lamellar structures can be enhanced by annealing in the presence of benzoic acid, which also acts as an epitaxial substrate. Nevertheless, the resultant layer structure in the annealed solid is not the same as that found for paraffin wax fractions refined from petroleum. Probably because of a small but significant fraction of a very long chain ingredient, the lamellar separation is incomplete, incorporating a number of 'bridging molecules' that span the nascent lamellar interface.The same phenomenon has been described recently for a low molecular weight polyethylene. (author)

Increased accumulation of cuticular wax and expression of lipid transfer protein in response to periodic drying events in leaves of tree tobacco.

Science.gov (United States)

Cameron, Kimberly D; Teece, Mark A; Smart, Lawrence B

2006-01-01

Cuticular wax deposition and composition affects drought tolerance and yield in plants. We examined the relationship between wax and dehydration stress by characterizing the leaf cuticular wax of tree tobacco (Nicotiana glauca L. Graham) grown under periodic dehydration stress. Total leaf cuticular wax load increased after each of three periods of dehydration stress using a CH2Cl2 extraction process. Overall, total wax load increased 1.5- to 2.5-fold, but composition of the wax was not altered. Homologous series of wax components were classified into organic groups; n-hentriacontane was the largest component (>75%) with alcohols and fatty acids representing drying event. Leaves excised from plants subjected to multiple drying events were more resistant to water loss compared to leaves excised from well-watered plants, indicating that there is a negative relationship between total wax load and epidermal conductance. Lipid transfer proteins (LTPs) are thought to be involved in the transfer of lipids through the extracellular matrix for the formation of cuticular wax. Using northern analysis, a 6-fold increase of tree tobacco LTP gene transcripts was observed after three drying events, providing further evidence that LTP is involved in cuticle deposition. The simplicity of wax composition and the dramatic wax bloom displayed by tree tobacco make this an excellent species in which to study the relationship between leaf wax deposition and drought tolerance.

Biodiesel production from Jatropha curcas oil

Energy Technology Data Exchange (ETDEWEB)

Jain, Siddharth; Sharma, M.P. [Alternate Hydro Energy Centre, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

2010-12-15

In view of the fast depletion of fossil fuel, the search for alternative fuels has become inevitable, looking at huge demand of diesel for transportation sector, captive power generation and agricultural sector, the biodiesel is being viewed a substitute of diesel. The vegetable oils, fats, grease are the source of feedstocks for the production of biodiesel. Significant work has been reported on the kinetics of transesterification of edible vegetable oils but little work is reported on non-edible oils. Out of various non-edible oil resources, Jatropha curcas oil (JCO) is considered as future feedstocks for biodiesel production in India and limited work is reported on the kinetics of transesterification of high FFA containing oil. The present study reports a review of kinetics of biodiesel production. The paper also reveals the results of kinetics study of two-step acid-base catalyzed transesterification process carried out at pre-determined optimum temperature of 65 and 50 C for esterification and transesterification process, respectively, under the optimum condition of methanol to oil ratio of 3:7 (v/v), catalyst concentration 1% (w/w) for H{sub 2}SO{sub 4} and NaOH and 400 rpm of stirring. The yield of methyl ester (ME) has been used to study the effect of different parameters. The maximum yield of 21.2% of ME during esterification and 90.1% from transesterification of pretreated JCO has been obtained. This is the first study of its kind dealing with simplified kinetics of two-step acid-base catalyzed transesterification process carried at optimum temperature of both the steps which took about 6 h for complete conversion of TG to ME. (author)

Preparation and Characterization of Sugar Cane Wax Microspheres ...

African Journals Online (AJOL)

... and characterize indomethacin (IM) microspheres prepared with sugar cane wax microsperes. Methods: Microspheres were prepared by melt-emulsified dispersion and cooling-induced solidification method. The microspheres were characterized by scanning electron microscopy (SEM) and differntial scanning calorimetry ...

Lipase-producing fungi for potential wastewater treatment and ...

African Journals Online (AJOL)

The use of fungal biomass as a lipase biocatalyst represents an attractive approach for the treatments of oil wastewater as well as for the production of biodiesel from oil and residual grease, due to its greater stability, possibility of reuse, and lower cost. In this work, 20 filamentous fungi were isolated from the grease trap ...

A review on wax printed microfluidic paper-based devices for international health.

Science.gov (United States)

Altundemir, S; Uguz, A K; Ulgen, K

2017-07-01

Paper-based microfluidics has attracted attention for the last ten years due to its advantages such as low sample volume requirement, ease of use, portability, high sensitivity, and no necessity to well-equipped laboratory equipment and well-trained manpower. These characteristics have made paper platforms a promising alternative for a variety of applications such as clinical diagnosis and quantitative analysis of chemical and biological substances. Among the wide range of fabrication methods for microfluidic paper-based analytical devices ( μ PADs), the wax printing method is suitable for high throughput production and requires only a commercial printer and a heating source to fabricate complex two or three-dimensional structures for multipurpose systems. μ PADs can be used by anyone for in situ diagnosis and analysis; therefore, wax printed μ PADs are promising especially in resource limited environments where people cannot get sensitive and fast diagnosis of their serious health problems and where food, water, and related products are not able to be screened for toxic elements. This review paper is focused on the applications of paper-based microfluidic devices fabricated by the wax printing technique and used for international health. Besides presenting the current limitations and advantages, the future directions of this technology including the commercial aspects are discussed. As a conclusion, the wax printing technology continues to overcome the current limitations and to be one of the promising fabrication techniques. In the near future, with the increase of the current interest of the industrial companies on the paper-based technology, the wax-printed paper-based platforms are expected to take place especially in the healthcare industry.

Preliminary detection of native lipase producing microorganisms for bio diesel production

International Nuclear Information System (INIS)

Ciudad, G.; Jorquera, M.; Briones, R.; Azocar, L.; Leal, J.; Navia, R.

2009-01-01

Lipase producing microorganisms (LPM) may catalyze the hydrolysis or transesterification of triacylglycerols to alkyl esters of fatty acids (bio diesel). The main objective of this work was to detect LPM in oil and grease contaminated environments for future applications in bio diesel production from rapeseed oil. Samples from contaminated soil (with rapeseed oil) from an industrial facility and contaminated soil (with salmon grease) near to a fish wastewater treatment plant were collected. (Author)

Preliminary detection of native lipase producing microorganisms for bio diesel production

Energy Technology Data Exchange (ETDEWEB)

Ciudad, G.; Jorquera, M.; Briones, R.; Azocar, L.; Leal, J.; Navia, R.

2009-07-01

Lipase producing microorganisms (LPM) may catalyze the hydrolysis or transesterification of triacylglycerols to alkyl esters of fatty acids (bio diesel). The main objective of this work was to detect LPM in oil and grease contaminated environments for future applications in bio diesel production from rapeseed oil. Samples from contaminated soil (with rapeseed oil) from an industrial facility and contaminated soil (with salmon grease) near to a fish wastewater treatment plant were collected. (Author)

Development and Properties of a Wax Ester Hydrolase in the Cotyledons of Jojoba Seedlings 1

Science.gov (United States)

Huang, Anthony H. C.; Moreau, Robert A.; Liu, Kitty D. F.

1978-01-01

The activity of a wax ester hydrolase in the cotyledons of jojoba (Simmondsia chinensis) seedlings increased drastically during germination, parallel to the development of the gluconeogenic process. The enzyme at its peak of development was obtained in association with the wax body membrane, and its properties were studied. It had an optimal activity at alkaline pH (8.5-9). The apparent Km value for N-methylindoxylmyristate was 93 μM. It was stable at 40 C for 30 min but was inactivated at higher temperature. Various divalent cations and ethylenediaminetetraacetate had little effect on the activity. p-Chloromercuribenzoate was a strong inhibitor of the enzyme activity, and its effect was reversed by subsequent addition of dithiothreitol. It had a broad substrate specificity with highest activities on monoglycerides, wax esters, and the native substrate (jojoba wax). PMID:16660288

Printed wax masks for 254 nm deep-UV pattering of PMMA-based microfluidics

International Nuclear Information System (INIS)

Fan, Yiqiang; Liu, Yang; Li, Huawei; Foulds, Ian G

2012-01-01

This paper reports a new technique for masking deep-UV exposure of poly(methyl methacrylate) (PMMA) using a printed wax mask. This technique provides an inexpensive and bulk fabrication method for PMMA structures. The technique involves the direct printing of the mask onto a polymer sheet using a commercial wax printer. The wax layer was then transferred to a PMMA substrate using a thermal laminator, exposed using deep-UV (with a wavelength of 254 nm), developed in an IPA:water solution, and completed by bonding on a PMMA cap layer. A sample microfluidic device fabricated with this method is also presented, with the microchannel as narrow as 50 µm. The whole process is easy to perform without the requirement for any microfabrication facilities. (technical note)

Particulate pollutants are capable to 'degrade' epicuticular waxes and to decrease the drought tolerance of Scots pine (Pinus sylvestris L.).

Science.gov (United States)

Burkhardt, Juergen; Pariyar, Shyam

2014-01-01

Air pollution causes the amorphous appearance of epicuticular waxes in conifers, usually called wax 'degradation' or 'erosion', which is often correlated with tree damage symptoms, e.g., winter desiccation. Previous investigations concentrated on wax chemistry, with little success. Here, we address the hypothesis that both 'wax degradation' and decreasing drought tolerance of trees may result from physical factors following the deposition of salt particles onto the needles. Pine seedlings were sprayed with dry aerosols or 50 mM solutions of different salts. The needles underwent humidity changes within an environmental scanning electron microscope, causing salt expansion on the surface and into the epistomatal chambers. The development of amorphous wax appearance by deliquescent salts covering tubular wax fibrils was demonstrated. The minimum epidermal conductance of the sprayed pine seedlings increased. Aerosol deposition potentially 'degrades' waxes and decreases tree drought tolerance. These effects have not been adequately considered thus far in air pollution research. Copyright © 2013 Elsevier Ltd. All rights reserved.

A new approach to model strain change of gelled waxy crude oil under constant stress

DEFF Research Database (Denmark)

Hou, Lei; Song, Changyu; Yan, Wei

2014-01-01

Deformation of gelled waxy crude oil with loaded stress is worthy of research for the flow assurance of pipelining system. A dispersion parameter was introduced to characterize the disruption degree of wax crystal structure in crude oil with shear action. Based on fractional calculus theory, a rh...... monotonously with test temperature. Multiple creep curves of gelled waxy crude oil at a certain temperature can be described with this model......., a rheological model incorporating dispersion parameter was proposed to describe creep of gelled waxy crude. A discrete and numerical algorithm was proposed to solve the model. Combining with the experimental results of five kinds of waxy crude oil, the model parameters were regressed and found to change...

Tendency of lubricating oil manufacturing process

Energy Technology Data Exchange (ETDEWEB)

Seki, Toshio

1988-09-30

The manufacturing method of paraffin base oil and the tendency are explained in details. The base oil is distillate of petroleum which is obtained at the high boiling of 400/degree/C or higher. The base oil is made from the distillate which is obtained through solvent deasphalting of the vacuum distillated residual oil. The refining process of those material is classified into the two different process steps such as refining and modifying process step in which the quality of the material is improved while eliminating unstable resin, aromatic compound, and sulfur contained in the material, and dewaxing process step in which the wax contained in the material is removed. The former is combination of the two different process steps such as solvent extraction process and hydrogen finishing process or hydroforming process. The latter is a combination of the two different process steps such as solvent dewaxing and catalytic dewaxing (hydro-dewaxing). Various examples of reactions, features and industrial processes are given in accordance with each of these process steps. Regarding the tendency toward the future, the kinds of materials will be expanded in the way that naphthene base oil will adopted as the material oil along with diversification of the quality of lubricating oil, and the processing technology including two-stage processing, catalytic dewaxing, etc. will be expected to be improved. 18 references, 11 figures, 7 tables.