Sample records for volcanoes high electrical

  1. Electrical conductivity of intermediate magmas from Uturuncu Volcano (Bolivia) (United States)

    Laumonier, Mickael; Gaillard, Fabrice; Sifre, David


    Magmas erupted at Uturuncu volcano (South Bolivia) comes from the Altiplano-Puna Magma Body (APMB, Chile-Bolivia), a crustal massive body of 80 km long by 10 km thick located at ~ 35 km depth named. Recent magneto telluric surveys reveal a resistivity lower than 1 ohm.m due to the presence of melt which could result in the reactivation of the volcano. In order to better constrain the resistivity profiles and thus the conditions of magma storage of the APMB, we have performed in situ electrical measurements on natural dacites and andesites from Uturuncu with a 4-wire set up in a piston cylinder and internally heated pressure vessel. The range of temperature (500 to 1300°C), pressure (0.3 to 2 Gpa), and the various water contents covers the respective ranges occurring at natural conditions. The results show that the conductivity increases with the temperature and the water content but slightly decreases with the pressure. Then a model was built from these results so as to help in (i) interpreting the electrical signature of natural magmas, (ii) constraining their conditions (chemical composition, temperature, pressure, water content, melt fraction) from the source to the storage location and (iii) providing information on the interior structure of a volcano and its reservoir.

  2. Volcano electrical tomography unveils edifice collapse hazard linked to hydrothermal system structure and dynamics (United States)

    Rosas-Carbajal, Marina; Komorowski, Jean-Christophe; Nicollin, Florence; Gibert, Dominique


    Catastrophic collapses of the flanks of stratovolcanoes constitute a major hazard threatening numerous lives in many countries. Although many such collapses occurred following the ascent of magma to the surface, many are not associated with magmatic reawakening but are triggered by a combination of forcing agents such as pore-fluid pressurization and/or mechanical weakening of the volcanic edifice often located above a low-strength detachment plane. The volume of altered rock available for collapse, the dynamics of the hydrothermal fluid reservoir and the geometry of incipient collapse failure planes are key parameters for edifice stability analysis and modelling that remain essentially hidden to current volcano monitoring techniques. Here we derive a high-resolution, three-dimensional electrical conductivity model of the La Soufrière de Guadeloupe volcano from extensive electrical tomography data. We identify several highly conductive regions in the lava dome that are associated to fluid saturated host-rock and preferential flow of highly acid hot fluids within the dome. We interpret this model together with the existing wealth of geological and geochemical data on the volcano to demonstrate the influence of the hydrothermal system dynamics on the hazards associated to collapse-prone altered volcanic edifices. PMID:27457494

  3. Volcano electrical tomography unveils edifice collapse hazard linked to hydrothermal system structure and dynamics. (United States)

    Rosas-Carbajal, Marina; Komorowski, Jean-Christophe; Nicollin, Florence; Gibert, Dominique


    Catastrophic collapses of the flanks of stratovolcanoes constitute a major hazard threatening numerous lives in many countries. Although many such collapses occurred following the ascent of magma to the surface, many are not associated with magmatic reawakening but are triggered by a combination of forcing agents such as pore-fluid pressurization and/or mechanical weakening of the volcanic edifice often located above a low-strength detachment plane. The volume of altered rock available for collapse, the dynamics of the hydrothermal fluid reservoir and the geometry of incipient collapse failure planes are key parameters for edifice stability analysis and modelling that remain essentially hidden to current volcano monitoring techniques. Here we derive a high-resolution, three-dimensional electrical conductivity model of the La Soufrière de Guadeloupe volcano from extensive electrical tomography data. We identify several highly conductive regions in the lava dome that are associated to fluid saturated host-rock and preferential flow of highly acid hot fluids within the dome. We interpret this model together with the existing wealth of geological and geochemical data on the volcano to demonstrate the influence of the hydrothermal system dynamics on the hazards associated to collapse-prone altered volcanic edifices.

  4. Volcanoes (United States)

    ... or more from a volcano. Before a Volcanic Eruption The following are things you can do to ... in case of an emergency. During a Volcanic Eruption Follow the evacuation order issued by authorities and ...

  5. Volcanoes

    Institute of Scientific and Technical Information of China (English)


    In the past thousand years,volcanoes have claimed more than 300,000 lives. Volcanology is ayoung and dangerous science that helps us against the power of the Earth itself.We live on a fiery planet. Nearly 2000 miles beneath our feet, the Earth's inner core reachestemperatures of 12,000 degrees Fahrenheit. Molten rock or magma, rises to the earth's surface. Acold, rigid crust fractured into some twenty plates. When magma breaks through crust it becomes

  6. Electrical Resistivity Structure and Helium Isotopes around Naruko Volcano, Northeastern Japan and Its Implication for the Distribution of Crustal Magma

    Directory of Open Access Journals (Sweden)

    Koichi Asamori


    Full Text Available The two-dimensional electrical resistivity structure beneath Naruko volcano was determined using magnetotelluric soundings. The resulting model shows that a prominent conductor exists through the middle crust to the uppermost mantle beneath the volcano. The location of the conductor agrees closely with a seismic low-velocity zone. Low-frequency microearthquakes occur near the conductor around the Moho depth. The cutoff depth of crustal earthquakes is coincident with the upper boundary of the conductor, implying that the conductor has a temperature appreciably higher than 400∘C. Furthermore, new helium isotope data from hot springs around the volcano were obtained. The spatial distribution of the observed 3He/4He ratios reveals the extent of mantle-derived materials beneath Naruko volcano. Consequently, it is apparent that the conductor determined beneath the volcano reflects the presence of high-temperature mantle-derived materials such as magmas and/or related fluids derived from active magmatism in the northeastern Japan subduction zone.

  7. Electrical structure of Plaine des Sables caldera, Piton de la Fournaise volcano (Reunion Island

    Directory of Open Access Journals (Sweden)

    P. A. Schnegg


    Full Text Available An Audio Magnetotelluric (AMT profile has been carried out across the Plaine des Sables, a former caldera of the active Piton de la Fournaise volcano, Reunion Island. Located in the Western Indian Ocean, between the Mascarene and Madagascar basins, this basaltic shield volcano originates from the activity of a hot spot. Our aim was to determine the internal structure of the volcano, in particular the shallow electrical properties of an area extending between the old and the new caldera rims. Although several teams had already conducted AMT work in this region a few years ago, there was a need for more a detailed, in depth survey. Our final model displays a noticeable slope of the Plaine des Sables basement oriented toward the present Fournaise summit. This slope is interpreted as resulting from successive landslides toward the ocean. We conclude that this dipping, electrically good conducting layer, probably belongs to the flat layering of an older caldera.

  8. Climbing in the high volcanoes of central Mexico (United States)

    Secor, R. J.


    A chain of volcanoes extends across central Mexico along the 19th parallel, a line just south of Mexico City. The westernmost of these peaks is Nevado de Colima at 4,636 feet above sea level. A subsidiary summit of Nevado de Colima is Volcan de Colima, locally called Fuego (fire) it still emits sulphurous fumes and an occasional plume of smoke since its disastrous eruption in 1941. Parictuin, now dormant, was born in the fall of 1943 when a cornfield suddenly erupted. Within 18 months, the cone grew more than 1,700 feet. Nevado de Toluca is a 15,433-foot volcanic peak south of the city of Toluca. Just southeast of Mexico City are two high volcanoes that are permanently covered by snow: Iztaccihuatl (17,342 fet) and Popocatepetl (17,887 feet) Further east is the third highest mountain in North America: 18,700-foot Citlateptl, or El Pico de Orizaba. North of these high peaks are two volcanoes, 14, 436-foot La Malinche and Cofre de Perote at 14,048 feet. This range of mountains is known variously as the Cordillera de Anahuac, the Sierra Volcanica Transversal, or the Cordillera Neovolcanica. 

  9. Strong S-wave attenuation and actively degassing magma beneath Taal volcano, Philippines, inferred from source location analysis using high-frequency seismic amplitudes (United States)

    Kumagai, H.; Lacson, R. _Jr., Jr.; Maeda, Y.; Figueroa, M. S., II; Yamashina, T.


    Taal volcano, Philippines, is one of the world's most dangerous volcanoes given its history of explosive eruptions and its close proximity to populated areas. A key feature of these eruptions is that the eruption vents were not limited to Main Crater but occurred on the flanks of Volcano Island. This complex eruption history and the fact that thousands of people inhabit the island, which has been declared a permanent danger zone, together imply an enormous potential for disasters. The Philippine Institute of Volcanology and Seismology (PHIVOLCS) constantly monitors Taal, and international collaborations have conducted seismic, geodetic, electromagnetic, and geochemical studies to investigate the volcano's magma system. Realtime broadband seismic, GPS, and magnetic networks were deployed in 2010 to improve monitoring capabilities and to better understand the volcano. The seismic network has recorded volcano-tectonic (VT) events beneath Volcano Island. We located these VT events based on high-frequency seismic amplitudes, and found that some events showed considerable discrepancies between the amplitude source locations and hypocenters determined by using onset arrival times. Our analysis of the source location discrepancies points to the existence of a region of strong S-wave attenuation near the ground surface beneath the east flank of Volcano Island. This region is beneath the active fumarolic area and above sources of pressure contributing inflation and deflation, and it coincides with a region of high electrical conductivity. The high-attenuation region matches that inferred from an active-seismic survey conducted at Taal in 1993. Our results, synthesized with previous results, suggest that this region represents actively degassing magma near the surface, and imply a high risk of future eruptions on the east flank of Volcano Island.

  10. Cyclic Explosivity in High Elevation Phreatomagmatic Eruptions at Ocean Island Volcanoes: Implications for Aquifer Pressurization and Volcano Flank Destabilization. (United States)

    Tarff, R.; Day, S. J.; Downes, H.; Seghedi, I.


    Groundwater heating and pressurization of aquifers trapped between dikes in ocean island volcanoes has been proposed as a mechanism for destabilizing and triggering large-volume flank collapses. Previous modelling has indicated that heat transfer from sustained magma flow through dikes during eruption has the potential to produce destabilizing levels of pressure on time scales of 4 to 400 days, if the aquifers remain confined. Here we revisit this proposal from a different perspective. We examine evidence for pressure variations in dike-confined aquifers during eruptions at high elevation vents on ocean island volcanoes. Initially magmatic, these eruptions change to mostly small-volume explosive phreatomagmatic activity. A recent example is the 1949 eruption on La Palma, Canary Islands. Some such eruptions involve sequences of larger-volume explosive phases or cycles, including production of voluminous low-temperature, pyroclastic density currents (PDC). Here we present and interpret data from the Cova de Paul crater eruption (Santo Antao, Cape Verde Islands). The phreatomagmatic part of this eruption formed two cycles, each culminating with eruption of PDCs. Compositional and textural variations in the products of both cycles indicate that the diatreme fill began as coarse-grained and permeable which allowed gas to escape. During the eruption, the fill evolved to a finer grained, poorly sorted, less permeable material, in which pore fluid pressures built up to produce violent explosive phases. This implies that aquifers adjacent to the feeder intrusion were not simply depressurized at the onset of phreatomagmatic explosivity but experienced fluctuations in pressure throughout the eruption as the vent repeatedly choked and emptied. In combination with fluctuations in magma supply rate, driving of aquifer pressurization by cyclical vent choking will further complicate the prediction of flank destabilization during comparable eruptions on ocean island volcanoes.

  11. "Living with Volcanoes": Cross-Curricular Teaching in the High School Classroom (United States)

    Jolley, Alison; Ayala, Gianna


    A new, interdisciplinary high school geoarchaeology curriculum unit, titled "Living with Volcanoes," was created and tested in two pilot lessons with 30 high school students total studying geography and classical civilization in northern England. Students were highly engaged during the curriculum unit and showed positive learning gains…

  12. Imaging mud fluid conduits of the Gunshuiping mud volcano with Electric Resistivity Methods (United States)

    Liao, Ling-Rong; Lin, Ting-Li; Chang, Ping-Yu


    We conducted the resistivity survey at the Gunshuiping mud volcano and produced a 3D model in order to delineate the mud-fluid conduits in the mud volcano system. The Gunshuiping mud volcano is located in a 175-m × 90-m plateau in Southwest of Taiwan. There are three main mud-volcano craters: craters 1, 2 and 3. Crater 3 is active and the others are inactive. We conducted thirteen survey lines using the Wenner configuration to obtain the resistivity profile images. The lengths of the lines are about 155 m and 60 m, which can resolve the resistivity image down to 30 m and 10 m in depth, respectively. The results appeared that there is a vertical structure under the crater 3, and we suggest that it is the mud-fluid conduit. There is a chamber at depth between 3 and 14 m, and we interpret it is the temporary storage of mud fluid during the erupting process. Beneath the craters 1 and 2, there is a near-surface, horizontal conduit connecting the craters 1 and 2. At depth between 15 and 25 m, the vertical conduit beneath the crater 3 and the horizontal conduit beneath the craters 1 and 2 are connected. The resistivity images clearly delineate the conduit underneath the craters and suggest that the crater 3 is the main erupting conduit, which is consistent with the surface features, in the Gunshuiping mud volcano system.

  13. Virunga Volcanoes Supersite: a collaborative initiative to improve Geohazards Assessment and Monitoring of Active Volcanoes in a highly populated region (United States)

    Balagizi, Charles M.; Mahinda, Celestin K.; Yalire, Mathieu M.; Ciraba, Honoré M.; Mavonga, Georges T.


    Located within the western branch of the East African Rift System (EARS), the Virunga Volcanic Province is a young highly volcanically and seismically active region. It provides a unique opportunity to study deep mantle upwelling through the crust. Several Geohazards are encountered in this highly populated region, and include volcanic hazards (lava flows, volcanic gases and ash, …), earthquake hazard; landslide, mud flows and floods hazards. In addition, the overturn of Lake Kivu (which lies in the Kivu Graben, western branch of the EARS) could release huge CO2 and CH4 into the atmosphere. A few days after the January 17, 2002 Nyiragongo eruption whose lava flows devastated Goma city, destroying the houses of ˜120,000 people, forced a mass self-evacuation of ˜300,000 people of Goma (of estimated ˜400,000 inhabitants), and killed ˜140 people; the international scientific community deployed a "dream scientific team" to evaluate the state of Geohazards in the Virunga region. Particularly, the team had to check whether the stability of Lake Kivu that dissolves ˜300 and ˜60 km3 of CO2 and CH4 (at 0˚ C and 1 atm.) in its deep water was not disturbed due to Nyiragongo lava that entered the lake. Since 2002 several projects were funded with the main goal of accompanying the local scientific team to set up a more professional team to assess and continuous monitor Geohazards in the Virunga. For the time being, while Nyiragongo volcano solely threatens ˜1.5 million inhabitants of Goma (DR Congo) and Gisenyi (Rwanda) cities in addition to people living in the surrounding villages, and Lake Kivu threatening ˜3 million inhabitants of its catchment, the local scientists remain less qualified and equipped. Here we show that collaboration between Virunga local scientists and international scientists through the Geohazards Supersites network could be a most efficient pathway to improve Geohazards assessment and monitoring in the Virunga, and hence yield Disaster Risk

  14. Numerical tsunami hazard assessment of the submarine volcano Kick 'em Jenny in high resolution are (United States)

    Dondin, Frédéric; Dorville, Jean-Francois Marc; Robertson, Richard E. A.


    Landslide-generated tsunami are infrequent phenomena that can be potentially highly hazardous for population located in the near-field domain of the source. The Lesser Antilles volcanic arc is a curved 800 km chain of volcanic islands. At least 53 flank collapse episodes have been recognized along the arc. Several of these collapses have been associated with underwater voluminous deposits (volume > 1 km3). Due to their momentum these events were likely capable of generating regional tsunami. However no clear field evidence of tsunami associated with these voluminous events have been reported but the occurrence of such an episode nowadays would certainly have catastrophic consequences. Kick 'em Jenny (KeJ) is the only active submarine volcano of the Lesser Antilles Arc (LAA), with a current edifice volume estimated to 1.5 km3. It is the southernmost edifice of the LAA with recognized associated volcanic landslide deposits. The volcano appears to have undergone three episodes of flank failure. Numerical simulations of one of these episodes associated with a collapse volume of ca. 4.4 km3 and considering a single pulse collapse revealed that this episode would have produced a regional tsunami with amplitude of 30 m. In the present study we applied a detailed hazard assessment on KeJ submarine volcano (KeJ) form its collapse to its waves impact on high resolution coastal area of selected island of the LAA in order to highlight needs to improve alert system and risk mitigation. We present the assessment process of tsunami hazard related to shoreline surface elevation (i.e. run-up) and flood dynamic (i.e. duration, height, speed...) at the coast of LAA island in the case of a potential flank collapse scenario at KeJ. After quantification of potential initial volumes of collapse material using relative slope instability analysis (RSIA, VolcanoFit 2.0 & SSAP 4.5) based on seven geomechanical models, the tsunami source have been simulate by St-Venant equations-based code

  15. Electric effects induced by artificial seismic sources at Somma-Vesuvius volcano

    Directory of Open Access Journals (Sweden)

    Rosa Di Maio


    Full Text Available In this paper, we present a series of self-potential measurements at Somma-Vesuvius volcanic area acquired in conjunction with an active seismic tomography survey. The aim of our study is both to provide further confirmation to the occurrence of seismo-electric coupling and to identify sites suitable for self-potential signal monitoring at Somma-Vesuvius district. The data, which were collected along two perpendicular dipoles, show significant changes on the natural electric field pattern. These variations, attributable to electrokinetic processes triggered by the artificial seismic waves, were observed after explosions occurred at a distance less than 5 km from the SP dipole arrays. In particular, we found that the NW-SE component of the natural electric field was more sensible to the shots than the NE-SW one, and the major effects did not correspond to the nearest shots. Such evidences were interpreted considering the underground electrical properties as deduced by previous detailed resistivity and self-potential surveys performed in the study area.

  16. Environmental monitoring of El Hierro Island submarine volcano, by combining low and high resolution satellite imagery (United States)

    Eugenio, F.; Martin, J.; Marcello, J.; Fraile-Nuez, E.


    El Hierro Island, located at the Canary Islands Archipelago in the Atlantic coast of North Africa, has been rocked by thousands of tremors and earthquakes since July 2011. Finally, an underwater volcanic eruption started 300 m below sea level on October 10, 2011. Since then, regular multidisciplinary monitoring has been carried out in order to quantify the environmental impacts caused by the submarine eruption. Thanks to this natural tracer release, multisensorial satellite imagery obtained from MODIS and MERIS sensors have been processed to monitor the volcano activity and to provide information on the concentration of biological, chemical and physical marine parameters. Specifically, low resolution satellite estimations of optimal diffuse attenuation coefficient (Kd) and chlorophyll-a (Chl-a) concentration under these abnormal conditions have been assessed. These remote sensing data have played a fundamental role during field campaigns guiding the oceanographic vessel to the appropriate sampling areas. In addition, to analyze El Hierro submarine volcano area, WorldView-2 high resolution satellite spectral bands were atmospherically and deglinted processed prior to obtain a high-resolution optimal diffuse attenuation coefficient model. This novel algorithm was developed using a matchup data set with MERIS and MODIS data, in situ transmittances measurements and a seawater radiative transfer model. Multisensor and multitemporal imagery processed from satellite remote sensing sensors have demonstrated to be a powerful tool for monitoring the submarine volcanic activities, such as discolored seawater, floating material and volcanic plume, having shown the capabilities to improve the understanding of submarine volcanic processes.

  17. High resolution aeromagnetic anomaly map of Mount Etna volcano, Southern Italy (United States)

    D'Ajello Caracciolo, F.; Nicolosi, I.; Carluccio, R.; Chiappini, S.; De Ritis, R.; Giuntini, A.; Materni, V.; Messina, A.; Chiappini, M.


    A high resolution aeromagnetic survey of Mount Etna Volcano was carried out by the Airborne Geophysics Science Team of Istituto Nazionale di Geofisica e Vulcanologia (INGV), aimed at producing the most detailed magnetic anomaly map existing so far for this area. Two datasets of the total intensity of the Earth's Magnetic Field were collected at different altitudes to take into account the huge topographic variations of Etna volcano, that reaches elevations above 3300 m asl. One level was flown at the altitude of 2200 m whereas a second one over the central part, at about 3500 m of altitude. Since the region is characterized by a large presence of strongly magnetized volcanic products, the survey was carried out acquiring profile lines only, in order to optimize the resources. From the residual magnetic anomaly analysis we inferred two main trending lineaments (- 35°N and 0°N) that are related to regional tectonic stress field and we interpret the main magnetic anomaly as the effect of thickness variation of magnetized volcanic products due to the complex pre-volcanic basement morphology of Etna.

  18. High-resolution seismic structure analysis of an active submarine mud volcano area off SW Taiwan (United States)

    Lin, Hsiao-Shan; Hsu, Shu-Kun; Tsai, Wan-Lin; Tsai, Ching-Hui; Lin, Shin-Yi; Chen, Song-Chuen


    In order to better understand the subsurface structure related to an active mud volcano MV1 and to understand their relationship with gas hydrate/cold seep formation, we conducted deep-towed side-scan sonar (SSS), sub-bottom profiler (SBP), multibeam echo sounding (MBES), and multi-channel reflection seismic (MCS) surveys off SW Taiwan from 2009 to 2011. As shown in the high-resolution sub-bottom profiler and EK500 sonar data, the detailed structures reveal more gas seeps and gas flares in the study area. In addition, the survey profiles show several submarine landslides occurred near the thrust faults. Based on the MCS results, we can find that the MV1 is located on top of a mud diapiric structure. It indicates that the MV1 has the same source as the associated mud diapir. The blanking of the seismic signal may indicate the conduit for the upward migration of the gas (methane or CO2). Therefore, we suggest that the submarine mud volcano could be due to a deep source of mud compressed by the tectonic convergence. Fluids and argillaceous materials have thus migrated upward along structural faults and reach the seafloor. The gas-charged sediments or gas seeps in sediments thus make the seafloor instable and may trigger submarine landslides.

  19. Sustaining persistent lava lakes: Observations from high-resolution gas measurements at Villarrica volcano, Chile (United States)

    Moussallam, Yves; Bani, Philipson; Curtis, Aaron; Barnie, Talfan; Moussallam, Manuel; Peters, Nial; Schipper, C. Ian; Aiuppa, Alessandro; Giudice, Gaetano; Amigo, Álvaro; Velasquez, Gabriela; Cardona, Carlos


    Active lava lakes - as the exposed upper part of magmatic columns - are prime locations to investigate the conduit flow processes operating at active, degassing volcanoes. Persistent lava lakes require a constant influx of heat to sustain a molten state at the Earth's surface. Several mechanisms have been proposed to explain how such heat transfer can operate efficiently. These models make contrasting predictions with respect to the flow dynamics in volcanic conduits and should result in dissimilar volatile emissions at the surface. Here we look at high-frequency SO2 fluxes, plume composition, thermal emissions and aerial video footage from the Villarrica lava lake in order to determine the mechanism sustaining its activity. We found that while fluctuations are apparent in all datasets, none shows a stable periodic behaviour. These observations suggest a continuous influx of volatiles and magma to the Villarrica lava lake. We suggest that ascending volatile-rich and descending degassed magmas are efficiently mixed within the volcanic conduit, resulting in no clear periodic oscillations in the plume composition and flux. We compare our findings to those of other lava lakes where equivalent gas emission time-series have been acquired, and suggest that gas flux, magma viscosity and conduit geometry are key parameters determining which flow mechanism operates in a given volcanic conduit. The range of conduit flow regimes inferred from the few studied lava lakes gives a glimpse of the potentially wide spectrum of conduit flow dynamics operating at active volcanoes.

  20. Volcano Preparedness (United States)

    ... You might feel better to learn that an ‘active’ volcano is one that has erupted in the past ... miles away. If you live near a known volcano, active or dormant, following these tips will help you ...

  1. Bowie Lecture: High-Rate GPS: Earthquakes, Ice Sheets, and Volcanoes (United States)

    Larson, K. M.


    Today GPS networks installed around the world are used to quantify long-term plate rates and the temporal and spatial complexities of crustal deformation at plate boundaries. Daily position precisions of several mm and long-term position rates of 0.1 mm/yr are routinely reported. These kinds of precisions are the outcome of 20 years of sustained development of observable models, a global tracking network, and an accurate terrestrial reference frame. But many geophysical problems require positioning at intervals much smaller than these standard "one-day" GPS results. The focus of this talk will be subdaily positioning applications, specifically using GPS to measure displacements during and after earthquakes, volcanic events, and ice-sheet kinematics. The methods I have used to analyze high-rate GPS data vary depending on the geophysical signal and the frequencies and amplitudes of the GPS error sources. For volcano applications, Kalman filtering can significantly reduce the errors due to multipath without suppressing the geophysical signal. I will discuss new volcano results using the 2007 Father's Day dike intrusion dataset from Kilauea. A second filtering application will focus on ice sheet measurements from Greenland, where surface melt linked to rising temperatures causes temporal variations in ice sheet speed. Finally I will discuss high-rate GPS as applied to seismology. Smoothing or averaging as shown for the previous cases is not a reasonable GPS analysis strategy for ground motions during an earthquake, and thus alternate multipath mitigation techniques must be used. Fortunately, the repetition of the GPS orbit can be used to develop empirical multipath corrections, significantly improving the precision of high-rate GPS solutions. I'll focus on the Tokachi-Oki dataset, discussing both measurements of the seismic signal and early postseismic deformation.

  2. Separation of scattering and intrinsic attenuation at Asama volcano (Japan): Evidence of high volcanic structural contrasts (United States)

    Prudencio, Janire; Aoki, Yosuke; Takeo, Minoru; Ibáñez, Jesús M.; Del Pezzo, Edoardo; Song, WenZhan


    In this study we show 2D intrinsic- and scattering-Q images of Asama volcano obtained by analyzing 2320 waveforms from active data. Observed energy envelopes were fitted to the diffusion model and separate intrinsic- and scattering-Q images were produced using a back-projection method based on a Gaussian-type weighting function. Synthetic tests indicate robustness and reliability of the results. Areas of high scattering attenuation coincide with the volcanic edifice and the summit at which recent eruptions took place. The intrinsic dissipation pattern shows a strong contrast between the east and west side of the volcanic structure with the low values observed in the west interpreted as solidified magma bodies. Our results demonstrate a strong relationship between structural heterogeneities and attenuation processes in volcanic areas and confirm the effectiveness of the present technique, which can be used as an imaging tool complementary to conventional techniques.

  3. Lake sediments provide the first eruptive history for Corbetti, a high-risk Main Ethiopian Rift volcano (United States)

    Martin-Jones, Catherine M.; Lane, Christine S.; Pearce, Nicholas J. G.; Smith, Victoria C.; Lamb, Henry F.; Schaebitz, Frank; Viehberg, Finn; Brown, Maxwell C.; Frank, Ute; Asrat, Asfawossen


    A recent World Bank report found that 49 of Ethiopia's 65 known Holocene volcanoes pose a high-risk to the surrounding population. One of these volcanoes, Corbetti, located in the densely populated Main Ethiopian Rift (MER), has only one documented Holocene eruption. Any risk assessment for Corbetti is therefore highly uncertain. Reliable hazard forecasting is dependent on the completeness of volcanic records. In the case of Ethiopian Rift volcanoes complete records are hindered by frequently poorly exposed, buried and inaccessible proximal outcrops. Lake sediments can yield comprehensive, stratigraphically-resolved dossiers of past volcanism. Here we use volcanic ash (tephra) layers preserved in sediments from three MER lakes to provide the first record of Holocene volcanism for Corbetti. It shows that Corbetti has erupted explosively throughout the Holocene at an average return period of 800 years. Based on the thickness and dispersal of the tephras, at least six eruptions were of a large magnitude, and there were four eruptions in the past 2000 years. Future explosive eruptions are likely and these could have significant societal impacts, they could blanket nearby Awassa and Shashamene, home to 260,000 people, with pumice deposits. Our data indicate that the threat posed by Corbetti has been significantly underestimated. These data can be used to refine regional volcano monitoring and develop evacuation plans. This lake sediment-tephrostratigraphic approach shows significant potential for application throughout the East African Rift system, and is essential to understanding volcanic hazards in this rapidly developing region.

  4. Molecular dynamics in high electric fields (United States)

    Apostol, M.; Cune, L. C.


    Molecular rotation spectra, generated by the coupling of the molecular electric-dipole moments to an external time-dependent electric field, are discussed in a few particular conditions which can be of some experimental interest. First, the spherical-pendulum molecular model is reviewed, with the aim of introducing an approximate method which consists in the separation of the azimuthal and zenithal motions. Second, rotation spectra are considered in the presence of a static electric field. Two particular cases are analyzed, corresponding to strong and weak fields. In both cases the classical motion of the dipoles consists of rotations and vibrations about equilibrium positions; this motion may exhibit parametric resonances. For strong fields a large macroscopic electric polarization may appear. This situation may be relevant for polar matter (like pyroelectrics, ferroelectrics), or for heavy impurities embedded in a polar solid. The dipolar interaction is analyzed in polar condensed matter, where it is shown that new polarization modes appear for a spontaneous macroscopic electric polarization (these modes are tentatively called "dipolons"); one of the polarization modes is related to parametric resonances. The extension of these considerations to magnetic dipoles is briefly discussed. The treatment is extended to strong electric fields which oscillate with a high frequency, as those provided by high-power lasers. It is shown that the effect of such fields on molecular dynamics is governed by a much weaker, effective, renormalized, static electric field.

  5. Vanishing Volcano

    Institute of Scientific and Technical Information of China (English)



    Mauna Loa, the world’s largest active volcano,is sinking into the Pacific Ocean——and it’s taking the main island of Hawaii with it! The problem:The mighty volcano has gained too much weight, says Peter Lipman of the U. S. Geological Survey.

  6. Sustainable high productivity electric steelmaking

    Energy Technology Data Exchange (ETDEWEB)

    Apfel, J.


    Badische Stahlwerke (BSW) operates a high productivity steelshop with two 90 t ac arc furnaces that produced 1.97 Mt billet in 2004, coupled with a wire rod and a bar mill. The company has evolved an integrated environmental protection strategy to fulfil the objective of economic operation while complying with legal emissions requirements and adapting an active approach to environmental issues more broadly. (author)

  7. Evidence for high fluid/melt content beneath Krakatau volcano (Indonesia) from local earthquake tomography (United States)

    Jaxybulatov, Kairly; Koulakov, Ivan; Seht, Malte Ibs-von; Klinge, Klaus; Reichert, Christian; Dahren, Börje; Troll, Valentin R.


    Within the KRAKMON project for multiparameter monitoring of Anak Krakatau volcano (Indonesia), a network of temporary stations was installed on the islands of the Krakatau complex as well as in the surrounding areas of the Sunda Strait, Sumatra and Java. The network was operated from June 2005 until January 2006. More than 700 local events were recorded during this experiment, and travel times from these events were used to perform a tomographic inversion for P and S velocities and for the Vp/Vs ratio. In this study, special attention was paid to the validation of the computed model based on different tests, such as inversion of independent data subsets and synthetic modeling. Although the network configuration and the distribution of the events are not favorable for high-quality tomographic imaging, we have obtained some important and robust features which give information about sources of volcanic activity in the Krakatau complex. The most interesting feature of this study is a zone of high Vp/Vs ratio beneath the Krakatau complex. At depths down to 4 km depth we observe anticorrelation of higher P- and lower S-velocities that leads to Vp/Vs ratio higher than 2. This is a probable indicator of the presence of partially molten and/or with high fluid content material with a composition corresponding to deeper layers. It is important that the anomaly of high Vp/Vs ratio beneath the Krakatau complex appears to be separated in two parts at a depth of 5-6 km. This fits to results of geobarometric analysis that presume the existence of several levels of magma chambers beneath Anak Krakatau.

  8. Volcano-tectonic control of Merapi's lava dome splitting observed from high resolution TerraSAR-X data

    KAUST Repository

    Luehr, Birger-G.


    Volcanism at active andesite-dacite volcanoes is often associated with the formation and collapse of circular shaped protrusions of extruded, highly viscous lava, the so-called domes, which are emplaced in the near summit region. Growing domes may experience stable and instable structural phases, with a gradual transition in between. Dome collapse and the break-off of instable blocks of viscous lava may lead to pyroclastic flows, one of the most lethal hazards at stratovolcanoes. At Merapi volcano, Indonesia, nearly 50 % of all eruptions are accompanied by these phenomena. After the climactic eruption in 2010 which left an amphitheater in the summit region, a new dome started growing. Three years later, the dome reached a height of approximately 100 m and diameters of 220 and 190 m with a plateau-like surface area of 40,000m2 approximately. On 18/11/2013, an explosion occurred without identified precursors, leaving a major fracture cutting the complete dome structure. Based on high resolution TerraSAR-X satellite radar imagery, we could identify this linear fracture, traceable over ~200m in the long axis, and up to 40m width. After geocoding of the radar amplitude imagery, the fractures azimuthal trend could be compared to other structural lineaments, indicative of a significant NNW-SSE structural direction that has formed on Merapi volcano in the past. This alignment is also visible in a seismic velocity tomographic imagery for the upper crust, down to 15 km depth. The Merapi dome fractured in a NW-SE direction, and is consistent with the alignment of regional tectonic structures and of anticipated directions of pyroclastic flows. The fracture may be part of a larger volcano-tectonic system and may affect the dynamics and the stability of the Merapi dome.

  9. Sulfur speciation with high performance liquid chromatography as a tool for El Chichón volcano, crater lake monitoring (United States)

    Casas, Ana Silvia; Armienta, María Aurora; Ramos, Silvia


    The monitoring of sulfur species in crater lakes has proven to be useful for forecasting episodes of volcanic unrest in certain active volcanoes, including Poás, Costa Rica; Kusatsu-Shirane, Japan; and Mt. Ruapehu, New Zealand. In this study, we have improved the current geochemical monitoring of El Chichón volcano through the setting of optimal high-performance liquid chromatography conditions (HPLC) for the analysis of S2-, SO32-, S2O32-, S4O62- and SO42- using a common chromatographic system. The procedure was applied to the analysis of lake samples taken in March, July and October of 2014 and April of 2015. The results were promising, since nearly all species were detected (with the exception of S2O32-) in measurable amounts, including S2- (<0.85-5.05 mg/L), SO32- (<2.77-26.1 mg/L), S4O62- (108.27-303.82 mg/L) and SO42- (489.58-676.26 mg/L). The spatial distribution of these species along the lakeshore showed zones of increased concentrations to the east and southeast of the lake, which provides information on the distribution of faults or cracks that feed hydrothermal fluids to the lake. This method thus provides additional information linked to the volcanic and hydrothermal activity of the volcano.

  10. High resolution three-dimensional magnetization mapping in Tokachidake Volcano using low altitude airborne magnetic survey data (United States)

    Iwata, M.; Mogi, T.; Okuma, S.; Nakatsuka, T.


    Tokachidake Volcano, central Hokkaido, Japan erupted in 1926, 1962 and 1988-1989 in the 20th century from the central part. In recent years, expansions of the edifice of the volcano at shallow depth and increases of the volcanic smoke in the Taisho crater were observed (Meteorological Agency of Japan, 2014). Magnetic changes were observed at the 62-2 crater by repeated magnetic measurements in 2008-2009, implying a demagnetization beneath the crater (Hashimoto at al., 2010). Moreover, a very low resistivity part was found right under the 62-2 crater from an AMT survey (Yamaya et al., 2010). However, since the station numbers of the survey are limited, the area coverage is not sufficient. In this study, we have re-analyzed high-resolution aeromagnetic data to delineate the three-dimensional magnetic structure of the volcano to understand the nature of other craters.A low altitude airborne magnetic survey was conducted in 2014 mainly over the active areas of the volcano by the Ministry of Land, Infrastructure, Transport and Tourism to manage land slide risk in the volcano. The survey was flown at an altitude of 60 m above ground by a helicopter with a Cesium magnetometer in the towed-bird 30m below the helicopter. The low altitude survey enables us to delineate the detailed magnetic structure. We calculated magnetic anomaly distribution on a smooth surface assuming equivalent anomalies below the observation surface. Then the 3D magnetic imaging method (Nakatsuka and Okuma, 2014) was applied to the magnetic anomalies to reveal the three-dimensional magnetic structure.As a result, magnetization highs were seen beneath the Ground crater, Suribachi crater and Kitamuki crater. This implies that magmatic activity occurred in the past at these craters. These magma should have already solidified and acquired strong remanent magnetization. Relative magnetization lows were seen beneath the 62-2 crater and the Taisho crater where fumarolic activity is active. However a

  11. High frequency SO2 flux measurements at Semeru volcano, Indonesia, using the SO2 camera (United States)

    Smekens, J.; Burton, M. R.; Clarke, A. B.; Harijoko, A.; Wibowo, H.; Sawyer, G.


    SO2 monitoring is a common technique at many volcanic centers. Recently, automated networks of scanning spectrometers have led to great improvement in frequency and accuracy of measurements. Simultaneously a new instrument has been proposed to acquire 2D images of volcanic plumes in the UV spectrum. This imaging technique (hereafter referred to as the SO2 camera) provides additional contextual information, as well as a quantitative way of determining plume velocity from a single remote location, without relying on weather reports. These advantages are to be balanced against a loss of spectroscopic information associated with using band-pass filters that reduce precision in the measurements. We have developed a custom-built acquisition and processing software to be used with the SO2 camera developed by INGV-Pisa for monitoring of Etna and Stromboli, which consists of two Quantum Scientific Imaging CCD cameras equipped with UV filters and a USB2000+ spectrometer. We have tested the instrument at two power plants in Arizona, USA. We were able to successfully measure SO2 fluxes as low as 1-2 tons/day. We also validated our method by comparing the SO2 camera measurements against high-frequency in-situ measurements (1 data point every minute) obtained from chemical sensors within the stacks. We have also used the SO2 camera during a field campaign at Semeru volcano, Indonesia, in May and June of 2013. Semeru is a persistently active explosive volcano, whose latest eruption began in 1967. Its eruptive behavior can be characterized by cyclic dome growth and collapse in the active crater and frequent small magnitude explosions occurring at periods of minutes to hours. We found that the majority of SO2 at Semeru is released during the explosive phases (instantaneous peaks of up to 40 kg/s), with passive emission levels between explosions fluctuating from 0-5 kg/s. After the initial explosive release, emission returns to background levels following an exponential decline over

  12. Dante's volcano (United States)


    This video contains two segments: one a 0:01:50 spot and the other a 0:08:21 feature. Dante 2, an eight-legged walking machine, is shown during field trials as it explores the inner depths of an active volcano at Mount Spurr, Alaska. A NASA sponsored team at Carnegie Mellon University built Dante to withstand earth's harshest conditions, to deliver a science payload to the interior of a volcano, and to report on its journey to the floor of a volcano. Remotely controlled from 80-miles away, the robot explored the inner depths of the volcano and information from onboard video cameras and sensors was relayed via satellite to scientists in Anchorage. There, using a computer generated image, controllers tracked the robot's movement. Ultimately the robot team hopes to apply the technology to future planetary missions.

  13. Scalloped electrodes for highly sensitive electrical measurements

    DEFF Research Database (Denmark)

    Vazquez Rodriguez, Patricia; Dimaki, Maria; Svendsen, Winnie Edith


    In this work we introduce a novel out-of-plane electrode with pronounced scalloped surface and high aspect ratio for electrical recordings of brain tissue in vitro, with the aim to reduce significantly the impedance of the measuring system. The profile and height of the structures is tailored...... by means of silicon fabrication techniques that sharpen them progressively and in a controlled manner. We will show that the use of the scalloped area achieves a great decrease in impedance, which is very significant for a reduction of noise in electrical measurements. The measured impedance reflects...

  14. High slot utilization systems for electric machines (United States)

    Hsu, John S


    Two new High Slot Utilization (HSU) Systems for electric machines enable the use of form wound coils that have the highest fill factor and the best use of magnetic materials. The epoxy/resin/curing treatment ensures the mechanical strength of the assembly of teeth, core, and coils. In addition, the first HSU system allows the coil layers to be moved inside the slots for the assembly purpose. The second system uses the slided-in teeth instead of the plugged-in teeth. The power density of the electric machine that uses either system can reach its highest limit.

  15. Anodizing of High Electrically Stressed Components

    Energy Technology Data Exchange (ETDEWEB)

    Flores, P. [NSTec; Henderson, D. J. [NSTec; Good, D. E. [NSTec; Hogge, K. [NSTec; Mitton, C. V. [NSTec; Molina, I. [NSTec; Naffziger, C. [NSTec; Codova, S. R. [SNL; Ormond, E. U. [SNL


    Anodizing creates an aluminum oxide coating that penetrates into the surface as well as builds above the surface of aluminum creating a very hard ceramic-type coating with good dielectric properties. Over time and use, the electrical carrying components (or spools in this case) experience electrical breakdown, yielding undesirable x-ray dosages or failure. The spool is located in the high vacuum region of a rod pinch diode section of an x-ray producing machine. Machine operators have recorded decreases in x-ray dosages over numerous shots using the reusable spool component, and re-anodizing the interior surface of the spool does not provide the expected improvement. A machine operation subject matter expert coated the anodized surface with diffusion pump oil to eliminate electrical breakdown as a temporary fix. It is known that an anodized surface is very porous, and it is because of this porosity that the surface may trap air that becomes a catalyst for electrical breakdown. In this paper we present a solution of mitigating electrical breakdown by oiling. We will also present results of surface anodizing improvements achieved by surface finish preparation and surface sealing. We conclude that oiling the anodized surface and using anodized hot dip sealing processes will have similar results.

  16. Highly Efficient Contactless Electrical Energy Transmission System (United States)

    Ayano, Hideki; Nagase, Hiroshi; Inaba, Hiromi

    This paper proposes a new concept for a contactless electrical energy transmission system for an elevator and an automated guided vehicle. The system has rechargeable batteries on the car and electrical energy is supplied at a specific place. When electric power is supplied to the car, it runs automatically and approaches the battery charger. Therefore, a comparatively large gap is needed between the primary transformer at the battery charger and the secondary transformer on the car in order to prevent damage which would be caused by a collision. In this case, a drop of the transformer coupling rate due to the large gap must be prevented. In conventional contactless electrical energy transmission technology, since electric power is received by a pick-up coil from a power line, a large-sized transformer is required. And when the distance over which the car runs is long, the copper loss of the line also increases. The developed system adopts a high frequency inverter using a soft switching method to miniaturize the transformer. The system has a coupling rate of 0.88 for a transformer gap length of 10mm and can operate at 91% efficiency.

  17. What Are Volcano Hazards? (United States)

    ... Sheet 002-97 Revised March 2008 What Are Volcano Hazards? Volcanoes give rise to numerous geologic and ... as far as 15 miles from the volcano. Volcano Landslides A landslide or debris avalanche is a ...

  18. High voltage electricity installations a planning perspective

    CERN Document Server

    Jay, Stephen Andrew


    The presence of high voltage power lines has provoked widespread concern for many years. High Voltage Electricity Installations presents an in-depth study of policy surrounding the planning of high voltage installations, discussing the manner in which they are percieved by the public, and the associated environmental issues. An analysis of these concerns, along with the geographical, environmental and political influences that shape their expression, is presented. Investigates local planning policy in an area of the energy sector that is of highly topical environmental and public concern Cover

  19. Remote measurement of high preeruptive water vapor emissions at Sabancaya volcano by passive differential optical absorption spectroscopy (United States)

    Kern, Christoph; Masias, Pablo; Apaza, Fredy; Reath, Kevin; Platt, Ulrich


    Water (H2O) is by far the most abundant volcanic volatile species and plays a predominant role in driving volcanic eruptions. However, numerous difficulties associated with making accurate measurements of water vapor in volcanic plumes have limited their use as a diagnostic tool. Here we present the first detection of water vapor in a volcanic plume using passive visible-light differential optical absorption spectroscopy (DOAS). Ultraviolet and visible-light DOAS measurements were made on 21 May 2016 at Sabancaya Volcano, Peru. We find that Sabancaya's plume contained an exceptionally high relative water vapor abundance 6 months prior to its November 2016 eruption. Our measurements yielded average sulfur dioxide (SO2) emission rates of 800–900 t/d, H2O emission rates of around 250,000 t/d, and an H2O/SO2 molecular ratio of 1000 which is about an order of magnitude larger than typically found in high-temperature volcanic gases. We attribute the high water vapor emissions to a boiling-off of Sabancaya's hydrothermal system caused by intrusion of magma to shallow depths. This hypothesis is supported by a significant increase in the thermal output of the volcanic edifice detected in infrared satellite imagery leading up to and after our measurements. Though the measurement conditions encountered at Sabancaya were very favorable for our experiment, we show that visible-light DOAS systems could be used to measure water vapor emissions at numerous other high-elevation volcanoes. Such measurements would provide observatories with additional information particularly useful for forecasting eruptions at volcanoes harboring significant hydrothermal systems.

  20. 30 CFR 57.12011 - High-potential electrical conductors. (United States)


    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-potential electrical conductors. 57.12011... Electricity Surface and Underground § 57.12011 High-potential electrical conductors. High-potential electrical conductors shall be covered, insulated, or placed to prevent contact with low potential conductors....

  1. High Resolution Wide Angle Seismics of A Mud Volcano - Crimea, Black Sea (United States)

    Bialas, J.; Broser, A.; Zillmer, M.; M52-1 Shipboard Party, The

    Gashydrates in marine sediments have been identified in the Black Sea first (Yefre- mova and Zhizchenko, 1974). Since russian researchers frequently reported gashy- drate findings near the seafloor from sediment cores (Soliviev and Ginsburg, 1994; Ivanov et al., 1998). Additional indications for emplacements of gas hydrates near the surface are observations of gas plumes by acoustic systems (Polikarpov et al., 1999) as well as direct observations of the ocean floor by video systems (Limonov et al., 1997). The existence of a Bottom-Simulating-Reflector (BSR) is used to identify gashydrate layers in seismic sections. These negative polarized reflector indicates the base of the hydrate stability zone (BHSZ) and generally cuts stratigraphic sequences. Still in dis- cussion is the question whether this reflection is caused by a velocity increase above the BHSZ or a velocity decrease due to free gas below the BHSZ (Pecher et al., 1996). Knowledge about gas and gashydrate concentrations in the sediments will be neces- sary to answer these questions. In January 2002 an interdisciplinary team of researches from Germany (Kiel and Bre- men), the Ukraine and Russia is going to carry out detailed investigations across a mud volcano in the waters offshore Crimea. Besides ocean floor video observations and geological sampling high resolution seismic data acquisition will be done. Record- ings of a multichannel streamer adopted to the alternating shot sequences (University of Bremen) will be accompanied by Ocean-Bottom-Hydrophones (OBH) and Ocean- Bottom-Seismometers (OBS) from GEOMAR, Kiel. During data acquisition three dif- ferent seismic sources (water gun, 2 GI gun) will be shot in alternating mode. There- fore three profiles of different frequency content will be achieved simultaneously. The corresponding resolution and depth of signal penetration will allow to study different sediment layers with increased resolution near the seafloor. It is planned to observe the shots with

  2. A prototype of an automated high resolution InSAR volcano-monitoring system in the MED-SUV project (United States)

    Chowdhury, Tanvir A.; Minet, Christian; Fritz, Thomas


    Volcanic processes which produce a variety of geological and hydrological hazards are difficult to predict and capable of triggering natural disasters on regional to global scales. Therefore it is important to monitor volcano continuously and with a high spatial and temporal sampling rate. The monitoring of active volcanoes requires the reliable measurement of surface deformation before, during and after volcanic activities and it helps for the better understanding and modelling of the involved geophysical processes. Space-borne synthetic aperture radar (SAR) interferometry (InSAR), persistent scatterer interferometry (PSI) and small baseline subset algorithm (SBAS) provide a powerful tool for observing the eruptive activities and measuring the surface changes of millimetre accuracy. All the mentioned techniques with deformation time series extraction address the challenges by exploiting medium to large SAR image stacks. The process of selecting, ordering, downloading, storing, logging, extracting and preparing the data for processing is very time consuming has to be done manually for every single data-stack. In many cases it is even an iterative process which has to be done regularly and continuously. Therefore, data processing becomes slow which causes significant delays in data delivery. The SAR Satellite based High Resolution Data Acquisition System, which will be developed at DLR, will automate this entire time consuming tasks and allows an operational volcano monitoring system. Every 24 hours the system runs for searching new acquired scene over the volcanoes and keeps track of the data orders, log the status and download the provided data via ftp-transfer including E-Mail alert. Furthermore, the system will deliver specified reports and maps to a database for review and use by specialists. The user interaction will be minimized and iterative processes will be totally avoided. In this presentation, a prototype of SAR Satellite based High Resolution Data

  3. Trace element abundances of high-MgO glasses from Kilauea, Mauna Loa and Haleakala volcanoes, Hawaii (United States)

    Wagner, T.P.; Clague, D.A.; Hauri, E.H.; Grove, T.L.


    We performed an ion-microprobe study of eleven high-MgO (6.7-14.8 wt%) tholeiite glasses from the Hawaiian volcanoes Kilauea, Mauna Loa and Haleakala. We determined the rare earth (RE), high field strength, and other selected trace element abundances of these glasses, and used the data to establish their relationship to typical Hawaiian shield tholeiite and to infer characteristics of their source. The glasses have trace element abundance characteristics generally similar to those of typical shield tholeiites, e.g. L(light)REE/H(heavy)REE(C1) > 1. The Kilauea and Mauna Loa glasses, however, display trace and major element characteristics that cross geochemical discriminants observed between Kilauea and Mauna Loa shield lavas. The glasses contain a blend of these discriminating chemical characteristics, and are not exactly like the typical shield lavas from either volcano. The production of these hybrid magmas likely requires a complexly zoned source, rather than two unique sources. When corrected for olivine fractionation, the glass data show correlations between CaO concentration and incompatible trace element abundances, indicating that CaO may behave incompatibly during melting of the tholeiite source. Furthermore, the tholeiite source must contain residual garnet and clinopyroxene to account for the variation in trace element abundances of the Kilauea glasses. Inversion modeling indicates that the Kilauea source is flat relative to C1 chondrites, and has a higher bulk distribution coefficient for the HREE than the LREE.

  4. High voltage and electrical insulation engineering

    CERN Document Server

    Arora, Ravindra


    "The book is written for students as well as for teachers and researchers in the field of High Voltage and Insulation Engineering. It is based on the advance level courses conducted at TU Dresden, Germany and Indian Institute of Technology Kanpur, India. The book has a novel approach describing the fundamental concept of field dependent behavior of dielectrics subjected to high voltage. There is no other book in the field of high voltage engineering following this new approach in describing the behavior of dielectrics. The contents begin with the description of fundamental terminology in the subject of high voltage engineering. It is followed by the classification of electric fields and the techniques of field estimation. Performance of gaseous, liquid and solid dielectrics under different field conditions is described in the subsequent chapters. Separate chapters on vacuum as insulation and the lightning phenomenon are included"--

  5. High-efficiency electrical charger for nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, M., E-mail: [National Centre for Metallurgical Research (CENIM-CSIC) (Spain); Huang, C. H. [Yuanpei University, Department of Environmental Engineering and Health (China)


    An electrical charger, based on a point-to-plate DC corona discharge, for the high-efficiency charging of aerosol particles with diameter of a few nanometers, has been designed, constructed, and evaluated. The discharge takes place between a needle and a perforated plate, and the results presented here have shown that this specific design allows reduction of electrostatic losses of charged particles within the charger in comparison with other typical designs. Besides, the small effective volume of the charger leads to a relatively small diffusion loss of particles. As a consequence of the reduced electrostatic and diffusion losses, the extrinsic charging efficiency attainable is higher than in similar devices.

  6. Three-dimensional velocity structure and high-precision earthquake relocations at Augustine, Akutan, and Makushin Volcanoes, Alaska (United States)

    Syracuse, E. M.; Thurber, C. H.; Power, J. A.; Prejean, S. G.


    Alaska contains over 100 volcanoes, 21 of which have been active within the past 20 years, including Augustine in Cook Inlet, and Akutan and Makushin in the central Aleutian arc. We incorporate 14-15 years of earthquake data from the Alaska Volcano Observatory (AVO) to obtain P-wave velocity structure and high-precision earthquake locations at each volcano. At Augustine, most relocated seismicity is beneath the summit at an average depth of 0.6 km. In the weeks leading to the 2006 eruption, seismicity shallowed and focused on a NW-SE line, suggestive of an inflating dike. Through August 2006, intermittent seismicity was observed at 1 to 4.5 km depth, pointing to an association with the transport of magma. Active-source data are also incorporated into the tomographic inversion, illuminating a high-velocity column beneath the summit, and elevated velocities on the south flank. The high-velocity column surrounds the observed deeper seismicity and is likely due to intruded volcanic material. The elevated velocities on the south flank are associated with uplifted zeolitzed sandstones. Akutan most recently erupted in 1992, before the seismic network was installed. Most seismicity is above 9 km depth, with 10% occurring between 14 to30 km depth. Seismicity is separated into two main groups that dip away from the caldera—one to the east and one to the west. The eastern group contains earthquakes from a swarm in early 1996 and the western group contains earthquakes from mid-1996 through the present that form rough lines radiating from the summit. Ongoing seismicity also occurs in a broader region beneath the caldera. Makushin most recently erupted in 1995, also prior to seismic monitoring by AVO. Relocations here show that most seismicity is at 3 to 13 km depth and either beneath the caldera or within one of two dipping clusters 20 km to the northeast. Additional seismicity occurs at up to 25 km depth beneath the summit, as well as scattered throughout the island at

  7. Muon radiography and deformation analysis of the lava dome formed by the 1944 eruption of Usu, Hokkaido--contact between high-energy physics and volcano physics--. (United States)

    K M Tanaka, Hiroyuki; Yokoyama, Izumi


    Lava domes are one of the conspicuous topographic features on volcanoes. The subsurface structure of the lava dome is important to discuss its formation mechanism. In the 1944 eruption of Volcano Usu, Hokkaido, a new lava dome was formed at its eastern foot. After the completion of the lava dome, various geophysical methods were applied to the dome to study its subsurface structure, but resulted in a rather ambiguous conclusion. Recently, from the results of the levelings, which were repeated during the eruption, "pseudo growth curves" of the lava dome were obtained. The curves suggest that the lava dome has a bulbous shape. In the present work, muon radiography, which previously proved effective in imaging the internal structure of Volcano Asama, has been applied to the Usu lava dome. The muon radiography measures the distribution of the "density length" of volcanic bodies when detectors are arranged properly. The result obtained is consistent with the model deduced from the pseudo growth curves. The measurement appears to afford useful method to clarify the subsurface structure of volcanoes and its temporal changes, and in its turn to discuss volcanic processes. This is a point of contact between high-energy physics and volcano physics.

  8. Muon radiography and deformation analysis of the lava dome formed by the 1944 eruption of Usu, Hokkaido —Contact between high-energy physics and volcano physics— (United States)

    TANAKA, Hiroyuki K. M.; YOKOYAMA, Izumi


    Lava domes are one of the conspicuous topographic features on volcanoes. The subsurface structure of the lava dome is important to discuss its formation mechanism. In the 1944 eruption of Volcano Usu, Hokkaido, a new lava dome was formed at its eastern foot. After the completion of the lava dome, various geophysical methods were applied to the dome to study its subsurface structure, but resulted in a rather ambiguous conclusion. Recently, from the results of the levelings, which were repeated during the eruption, “pseudo growth curves” of the lava dome were obtained. The curves suggest that the lava dome has a bulbous shape. In the present work, muon radiography, which previously proved effective in imaging the internal structure of Volcano Asama, has been applied to the Usu lava dome. The muon radiography measures the distribution of the “density length” of volcanic bodies when detectors are arranged properly. The result obtained is consistent with the model deduced from the pseudo growth curves. The measurement appears to afford useful method to clarify the subsurface structure of volcanoes and its temporal changes, and in its turn to discuss volcanic processes. This is a point of contact between high-energy physics and volcano physics. PMID:18941290

  9. 30 CFR 56.12011 - High-potential electrical conductors. (United States)


    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-potential electrical conductors. 56.12011... § 56.12011 High-potential electrical conductors. High-potential electrical conductors shall be covered, insulated, or placed to prevent contact with low potential conductors....

  10. Development and Assessment of an Automated High-Resolution InSAR Volcano-Monitoring System (United States)

    Chowdhury, Tanvir A.; Minet, Christian; Fritz, Thomas


    Monitoring volcanoes and volcanic areas using synthetic aperture radar (SAR) data is a well-established method of risk assessment. However, acquisition planning, ordering, and downloading are time and work intensive, but inevitable process. It has to be done not only once before the actual processing, but for continuous monitoring, it poses a continuous and expensive effort. Therefore an automatic acquisition and processing system is developed at DLR, which allows pseudo-continuous processing of data sequences over the test site and also be applicable to any other optional test-site extension, including the increase of data volume. This system reduces the load of manual work necessary to perform interferometric stacking and quickly gain first information on evolving geophysical processes at the, but not limited to the Italian supersites.

  11. Precise hypocentre relocation of microearthquakes in a high-temperature geothermal field: the Torfajökull central volcano, Iceland (United States)

    Lippitsch, Regina; White, Robert S.; Soosalu, Heidi


    The Torfajökull volcanic system is one of approximately 30 active volcanoes comprising the neovolcanic zones of Iceland. The central volcano of the system is the largest silicic centre in Iceland with a caldera of approximately 12 km diameter. Its high-temperature geothermal system is one of the most powerful in Iceland. Torfajökull is a source of persistent seismicity, where both high- and low-frequency earthquakes occur. To study this microseismicity in detail, a temporary array of 20 broad-band seismic stations was deployed between 2002 June and November. These temporary stations were embedded in the permanent South Iceland Lowland (SIL) network and data from nine adjacent SIL stations were included in this study. A minimum one-dimensional (1-D) velocity model with station corrections was computed for earthquake relocation by inverting manually picked P- and S-wave arrival times from events occurring in the Torfajökull volcanic centre and its surroundings. High-frequency earthquakes from the Torfajökull volcanic centre were then relocated calculating a non-linear, probabilistic solution to the earthquake location problem. Subsequently, we correlated the waveforms of these 121 events (~2000 observations) to define linked events, calculated the relative traveltime difference between event pairs and solved for the hypocentral separation between these events. The resulting high-resolution pattern shows a tighter clustering in epicentre and focal depth when compared with original locations. Earthquakes are mainly located beneath the caldera with hypocentres between 1 and 6 km depth and lie almost exclusively within the geothermal system. A sharp cut-off in seismicity at 3 km suggests either that there is a marked temperature increase or that this is a structural boundary. No seismic activity was observed in the fissure swarms to the northeast (NE) and southwest (SW) of the volcanic centre.

  12. Volcano seismology (United States)

    Chouet, B.


    A fundamental goal of volcano seismology is to understand active magmatic systems, to characterize the configuration of such systems, and to determine the extent and evolution of source regions of magmatic energy. Such understanding is critical to our assessment of eruptive behavior and its hazardous impacts. With the emergence of portable broadband seismic instrumentation, availability of digital networks with wide dynamic range, and development of new powerful analysis techniques, rapid progress is being made toward a synthesis of high-quality seismic data to develop a coherent model of eruption mechanics. Examples of recent advances are: (1) high-resolution tomography to image subsurface volcanic structures at scales of a few hundred meters; (2) use of small-aperture seismic antennas to map the spatio-temporal properties of long-period (LP) seismicity; (3) moment tensor inversions of very-long-period (VLP) data to derive the source geometry and mass-transport budget of magmatic fluids; (4) spectral analyses of LP events to determine the acoustic properties of magmatic and associated hydrothermal fluids; and (5) experimental modeling of the source dynamics of volcanic tremor. These promising advances provide new insights into the mechanical properties of volcanic fluids and subvolcanic mass-transport dynamics. As new seismic methods refine our understanding of seismic sources, and geochemical methods better constrain mass balance and magma behavior, we face new challenges in elucidating the physico-chemical processes that cause volcanic unrest and its seismic and gas-discharge manifestations. Much work remains to be done toward a synthesis of seismological, geochemical, and petrological observations into an integrated model of volcanic behavior. Future important goals must include: (1) interpreting the key types of magma movement, degassing and boiling events that produce characteristic seismic phenomena; (2) characterizing multiphase fluids in subvolcanic

  13. Solar electric energy supply at high altitude

    Energy Technology Data Exchange (ETDEWEB)

    Knaupp, W.; Mundschau, E. [Zentrum fur Sonnenenergie- und Wasserstoff-Forschung (ZSW), Ulm (Germany)


    Solar-hydrogen systems were analyzed regarding their usability as energy supply system for high altitude platforms. In a first step for an assessment of solar and photovoltaic resources near-ground spectral transmittances of atmosphere were extended with simplified height correction functions to achieve spectral irradiance descriptions versus atmospheric height up to 25 km. The influence of atmospheric height to different solar cell technologies regarding electrical performance was quantified at some examples for the aspect of spectral distribution with the help of the introduced spectral height factor. The main attention during analysis of the whole solar-hydrogen energy system was directed to characteristics of current or near term available technology. Specific power weight of photovoltaic system, electrolyzer, fuel cell and gas tanks and their dependence on operation mode and power range were assessed. A pre-design of a solar-hydrogen energy system was carried out for an airship (volume 580,000 m3) withstanding continuous wind speeds up to {approx} 130 km/h. The calculated coverage ratio of photovoltaic and load share of energy system mark the frame of usability. Depending on the airship size, shape and other external boundary conditions the total electrical energy demand could be covered by a solar-hydrogen energy system of current or near term technology for full year operation. However further investigations are necessary regarding e.g. further mass reductions. (author)

  14. Santorini Volcano (United States)

    Druitt, T.H.; Edwards, L.; Mellors, R.M.; Pyle, D.M.; Sparks, R.S.J.; Lanphere, M.; Davies, M.; Barreirio, B.


    Santorini is one of the most spectacular caldera volcanoes in the world. It has been the focus of significant scientific and scholastic interest because of the great Bronze Age explosive eruption that buried the Minoan town of Akrotiri. Santorini is still active. It has been dormant since 1950, but there have been several substantial historic eruptions. Because of this potential risk to life, both for the indigenous population and for the large number of tourists who visit it, Santorini has been designated one of five European Laboratory Volcanoes by the European Commission. Santorini has long fascinated geologists, with some important early work on volcanoes being conducted there. Since 1980, research groups at Cambridge University, and later at the University of Bristol and Blaise Pascal University in Clermont-Ferrand, have collected a large amount of data on the stratigraphy, geochemistry, geochronology and petrology of the volcanics. The volcanic field has been remapped at a scale of 1:10 000. A remarkable picture of cyclic volcanic activity and magmatic evolution has emerged from this work. Much of this work has remained unpublished until now. This Memoir synthesizes for the first time all the data from the Cambridge/Bristol/Clermont groups, and integrates published data from other research groups. It provides the latest interpretation of the tectonic and magmatic evolution of Santorini. It is accompanied by the new 1:10 000 full-colour geological map of the island.

  15. High-resolution 3D surface displacements from 2004 - 2012 at Santorini volcano, Greece measured by LiDAR-differencing (United States)

    Parks, M.; Pyle, D. M.; Nissen, E.; Mather, T. A.; Raptakis, C.; Nomikou, P.


    In January 2011 Santorini volcano entered a period of unrest characterised by earthquake swarms and caldera-wide uplift. Interferometric Synthetic Aperture Radar (InSAR) measurements indicate vertical motions of 8 - 14 cm across the central volcanic island of Nea Kameni since the onset of unrest. In April 2004, a NERC funded Airborne Research and Survey Facility (ARSF) flight acquired high-resolution (1m per pixel) light detection and ranging laser radar (LiDAR) data over the central volcanic islands of Nea Kameni and Palea Kameni. This survey was repeated in May 2012 to provide an updated digital elevation model (DEM). We apply a new method of differencing pre- and post- deformation LiDAR point clouds using the Iterative Closest Point (ICP) algorithm to produce a high-resolution grid of 3D surface displacements from 2004 - 2012. The 2004 ("source") and 2012 ("target") point clouds are first split into square subsets ("windows") and the displacement for each window is determined by iterating three steps: (1) identifying closest point pairs; (2) calculating the translation and rotation required that best aligns the paired points; (3) applying this transformation to the source cloud. The surface displacement map spans both a period of slow subsidence (from 2004 - 2010), and a subsequent period of inflation (from 2011 - 2012). We shall compare our results with those obtained from simple DEM elevation differencing and from InSAR. To our knowledge, this is the first application of the ICP technique to measuring volcanic deformation. This approach may be implemented at other volcanoes to monitor 3D surface displacements during periods of unrest.

  16. Turmoil at Turrialba Volcano (Costa Rica): Degassing and eruptive processes inferred from high-frequency gas monitoring. (United States)

    de Moor, J Maarten; Aiuppa, A; Avard, G; Wehrmann, H; Dunbar, N; Muller, C; Tamburello, G; Giudice, G; Liuzzo, M; Moretti, R; Conde, V; Galle, B


    Eruptive activity at Turrialba Volcano (Costa Rica) has escalated significantly since 2014, causing airport and school closures in the capital city of San José. Whether or not new magma is involved in the current unrest seems probable but remains a matter of debate as ash deposits are dominated by hydrothermal material. Here we use high-frequency gas monitoring to track the behavior of the volcano between 2014 and 2015 and to decipher magmatic versus hydrothermal contributions to the eruptions. Pulses of deeply derived CO2-rich gas (CO2/Stotal > 4.5) precede explosive activity, providing a clear precursor to eruptive periods that occurs up to 2 weeks before eruptions, which are accompanied by shallowly derived sulfur-rich magmatic gas emissions. Degassing modeling suggests that the deep magmatic reservoir is ~8-10 km deep, whereas the shallow magmatic gas source is at ~3-5 km. Two cycles of degassing and eruption are observed, each attributed to pulses of magma ascending through the deep reservoir to shallow crustal levels. The magmatic degassing signals were overprinted by a fluid contribution from the shallow hydrothermal system, modifying the gas compositions, contributing volatiles to the emissions, and reflecting complex processes of scrubbing, displacement, and volatilization. H2S/SO2 varies over 2 orders of magnitude through the monitoring period and demonstrates that the first eruptive episode involved hydrothermal gases, whereas the second did not. Massive degassing (>3000 T/d SO2 and H2S/SO2 > 1) followed, suggesting boiling off of the hydrothermal system. The gas emissions show a remarkable shift to purely magmatic composition (H2S/SO2 < 0.05) during the second eruptive period, reflecting the depletion of the hydrothermal system or the establishment of high-temperature conduits bypassing remnant hydrothermal reservoirs, and the transition from phreatic to phreatomagmatic eruptive activity.

  17. A high-resolution 40Ar/39Ar lava chronology and edifice construction history for Ruapehu volcano, New Zealand (United States)

    Conway, Chris E.; Leonard, Graham S.; Townsend, Dougal B.; Calvert, Andrew T.; Wilson, Colin J. N.; Gamble, John A.; Eaves, Shaun R.


    Ruapehu is an active 150 km3 andesite-dacite composite volcano located at the southern end of the Taupo Volcanic Zone, New Zealand. The growth of the present-day edifice has occurred throughout coeval eruptive and glacial histories since 200 ka. We present high-precision 40Ar/39Ar eruption ages for 46 samples and whole-rock major element geochemical data for 238 samples from lava flows. These new and existing data are interpreted in the context of geomorphologic and geologic mapping, volcano-ice interaction processes and glacier reconstructions to present an improved chronostratigraphic framework and new edifice evolution history for Ruapehu. Sub-glacial to ice-marginal effusive eruption of medium-K basaltic-andesites and andesites constructed the northern portion of the exposed edifice between 200 and 150 ka, and a wide southeast planèze as well as parts of the northern, eastern and western flanks between 160 and 80 ka. None of the dated lava flows have ages in the range of 80-50 ka, which may reflect an eruptive hiatus. Alternatively the lack of ages may be the result of erosion and burial of lavas and syn-eruptive glacial conveyance of lava flows to the ring-plain during glacial advance at 70-60 ka. From 50-15 ka edifice growth occurred via effusive eruptions onto the glaciated flanks of the volcano, resulting in construction of ice-bounded planèzes and ridges. The distribution of dated ice-marginal lavas indicates a general decrease in glacier thicknesses over this time, except for a short-lived period centred at 31 ka when peak ice cover was reached. The compositional ranges of medium- to high-K andesite and dacite lava flows within 50-35 ka eruptive packages define broadly bimodal high- and low-MgO trends. Lavas erupted at 35-22 ka have compositions that fill a transitional geochemical field between older dacites and younger andesites. Large-scale retreat of flank glaciers since 15 ka has resulted in intra-valley lava flow emplacement at elevations below

  18. Preliminary volcano-hazard assessment for Iliamna Volcano, Alaska (United States)

    Waythomas, Christopher F.; Miller, Thomas P.


    Iliamna Volcano is a 3,053-meter-high, ice- and snow-covered stratovolcano in the southwestern Cook Inlet region about 225 kilometers southwest of Anchorage and about 100 kilometers northwest of Homer. Historical eruptions of Iliamna Volcano have not been positively documented; however, the volcano regularly emits steam and gas, and small, shallow earthquakes are often detected beneath the summit area. The most recent eruptions of the volcano occurred about 300 years ago, and possibly as recently as 90-140 years ago. Prehistoric eruptions have generated plumes of volcanic ash, pyroclastic flows, and lahars that extended to the volcano flanks and beyond. Rock avalanches from the summit area have occurred numerous times in the past. These avalanches flowed several kilometers down the flanks and at least two large avalanches transformed to cohesive lahars. The number and distribution of known volcanic ash deposits from Iliamna Volcano indicate that volcanic ash clouds from prehistoric eruptions were significantly less voluminous and probably less common relative to ash clouds generated by eruptions of other Cook Inlet volcanoes. Plumes of volcanic ash from Iliamna Volcano would be a major hazard to jet aircraft using Anchorage International Airport and other local airports, and depending on wind direction, could drift at least as far as the Kenai Peninsula and beyond. Ashfall from future eruptions could disrupt oil and gas operations and shipping activities in Cook Inlet. Because Iliamna Volcano has not erupted for several hundred years, a future eruption could involve significant amounts of ice and snow that could lead to the formation of large lahars and downstream flooding. The greatest hazards in order of importance are described below and shown on plate 1.

  19. Mount Rainier active cascade volcano (United States)


    Mount Rainier is one of about two dozen active or recently active volcanoes in the Cascade Range, an arc of volcanoes in the northwestern United States and Canada. The volcano is located about 35 kilometers southeast of the Seattle-Tacoma metropolitan area, which has a population of more than 2.5 million. This metropolitan area is the high technology industrial center of the Pacific Northwest and one of the commercial aircraft manufacturing centers of the United States. The rivers draining the volcano empty into Puget Sound, which has two major shipping ports, and into the Columbia River, a major shipping lane and home to approximately a million people in southwestern Washington and northwestern Oregon. Mount Rainier is an active volcano. It last erupted approximately 150 years ago, and numerous large floods and debris flows have been generated on its slopes during this century. More than 100,000 people live on the extensive mudflow deposits that have filled the rivers and valleys draining the volcano during the past 10,000 years. A major volcanic eruption or debris flow could kill thousands of residents and cripple the economy of the Pacific Northwest. Despite the potential for such danger, Mount Rainier has received little study. Most of the geologic work on Mount Rainier was done more than two decades ago. Fundamental topics such as the development, history, and stability of the volcano are poorly understood.

  20. Mount Rainier active cascade volcano (United States)

    Mount Rainier is one of about two dozen active or recently active volcanoes in the Cascade Range, an arc of volcanoes in the northwestern United States and Canada. The volcano is located about 35 kilometers southeast of the Seattle-Tacoma metropolitan area, which has a population of more than 2.5 million. This metropolitan area is the high technology industrial center of the Pacific Northwest and one of the commercial aircraft manufacturing centers of the United States. The rivers draining the volcano empty into Puget Sound, which has two major shipping ports, and into the Columbia River, a major shipping lane and home to approximately a million people in southwestern Washington and northwestern Oregon. Mount Rainier is an active volcano. It last erupted approximately 150 years ago, and numerous large floods and debris flows have been generated on its slopes during this century. More than 100,000 people live on the extensive mudflow deposits that have filled the rivers and valleys draining the volcano during the past 10,000 years. A major volcanic eruption or debris flow could kill thousands of residents and cripple the economy of the Pacific Northwest. Despite the potential for such danger, Mount Rainier has received little study. Most of the geologic work on Mount Rainier was done more than two decades ago. Fundamental topics such as the development, history, and stability of the volcano are poorly understood.

  1. High-resolution digital elevation dataset for Newberry Volcano and vicinity, Oregon, based on lidar survey of August-September, 2010 and bathymetric survey of June, 2001 (United States)

    Bard, Joseph A.; Ramsey, David W.


    Newberry Volcano, one of the largest Quaternary volcanoes in the conterminous United States, is a broad shield-shaped volcano measuring 60 km north-south by 30 km east-west with a maximum elevation of more than 2 km above sea level. It is the product of deposits from thousands of eruptions, including at least 25 in (approximately) the last 12,000 years (the Holocene Epoch). Newberry Volcano has erupted as recently as 1,300 years ago, but isotopic ages indicate that the volcano began its growth as early as 0.6 million years ago. Such a long eruptive history together with recent activity suggests that Newberry Volcano is likely to erupt in the future. This DEM (digital elevation model) of Newberry Volcano contributes to natural hazard monitoring efforts, the study of regional geology, volcanic landforms, and landscape modification during and after future volcanic eruptions, both at Newberry Volcano or elsewhere globally. In collaboration with the USGS, the Oregon Department of Geology and Mineral Industries-led Oregon Lidar Consortium contracted Watershed Sciences to collect 500 square miles of high-precision airborne lidar (Light Detection and Ranging) data. These data provide a digital map of the ground surface beneath forest cover. The lidar-derived DEM is amended to include bathymetric surveys of East Lake and Paulina Lake. The bathymetric surveys were performed in June, 2001 by Bob Reynolds of Central Oregon Community College, Bend, Oregon. The bathymetry is mosaicked into the DEM in place of the lidar derived lake surfaces. This release is comprised of a DEM dataset accompanied by a hillshade raster, each divided into eighteen tiles. Each tile’s bounding rectangle is identical to the extent of the USGS 7.5 minute topographic quadrangles covering the same area. The names of the DEM tiles are eleven characters long (e.g., dem_xxxxxx) with the prefix, "dem", indicating the file is a DEM and the last seven characters corresponding to the map reference code of the

  2. The Albano Maar Lake high resolution bathymetry and dissolved CO 2 budget (Colli Albani volcano, Italy): Constrains to hazard evaluation (United States)

    Anzidei, Marco; Carapezza, Maria Luisa; Esposito, Alessandra; Giordano, Guido; Lelli, Matteo; Tarchini, Luca


    The Albano Lake is the deepest volcanic lake in Italy (- 167 m) and fills the youngest maar of the quiescent Colli Albani volcano. The lake has undergone significant level changes and lahar generating overflows occurred about 5800 yrs B.P. and likely in 398 b.C., when Romans excavated a tunnel drain through the maar wall. Hazardous lake rollovers and CO 2 release are still possible because the Albano volcano shows active ground deformation, gas emission and periodic seismic swarms. On November 2005, the first high resolution bathymetric survey of the Albano Lake was performed. Here we present the results provided by a Digital Elevation Model and 2-D and 3-D images of the crater lake floor, which is made by coalescent and partly overlapping craters and wide flat surfaces separated by some evident scarps. Submerged shorelines are identified at depths between - 20 m and - 41 m and indicate the occurrence of significant lake level changes, likely between 7.1 and 4.1 ka. The current lake volume is ~ 447.5 × 10 6 m 3 and the total quantity of dissolved CO 2 is 6850 t estimated by chemical analyses of samples collected on May 2006. A decrease of nearly one order of magnitude of the CO 2 dissolved in the lake water below - 120 m, observed from December 1997 to May 2006 (from 4190 to 465 t respectively), has been attributed to lake water overturn. The observed oscillations of the dissolved CO 2 concentrations justify the efforts of monitoring the chemical and physical characteristics of the lake. At present the quantity of dissolved CO 2 is very far from saturation and Nyos-type events cannot presently occur.

  3. Activity of Changbaishan Tianchi Volcano Since Late Pleistocene--The Constrain From Geochronology of High Precision U- Series Tims Method

    Institute of Scientific and Technical Information of China (English)

    Wang Fei; Chen Wenji; Zhang Zhonglu; Hu Yutai; Peng Zicheng


    11 samples of lava and pumice from the cone of Changbaishan Tianchi Volcano, Jiling, China, were dated by using high precision U - series TIMS method. We conclude that the bottom of the cone formed before 350 ka, the middle part in 70~80 ka, the upper during 20~ 1ka, and the top less than 1ka, and the age based periods of the volcano eruption since Late Pleistocene is given as follows: > 350ka, 70ka, 18 ~ 25ka, 10ka, 4C5ka, 1~0.75ka, which may offer the basis for the study of volcanic disaster in future. In addition, the principle of dating young volcanic rocks by using U - series TIMS method is introduced briefly. Differentiation characteristics of U and Th in different minerals of the volcanic rocks are discussed, and the ability producing isochrons, based on U and Th differentiation, are discussed. In the last part of the paper,the closure of samples to the elements U and Th, which is important for age results, is discussed by using (234U/238U)radioactivity ratio which can be used to monitor if the samples have been weathered or eroded or leached since the time they formed. In this study, all samples have (234U/238U) activity ratios within 1% of secular equilibrium ((234U/238U) radioactivity ratios are unity), indicating no disturbance of the 234U- 238U system. All of these discussions show that the TIMS method is good to date Tianchi volcanics and the results are reliable.

  4. Insights into Proximal-Medial Pyroclastic Density Current Deposits at a High-Risk Glaciated Volcano: Mt Ruapehu, New Zealand (United States)

    Cowlyn, J.; Kennedy, B.; Gravley, D. M.; Cronin, S. J.; Pardo, N.; Wilson, T. M.; Leonard, G.; Townsend, D.; Dufek, J.


    Pyroclastic density currents (PDCs) are a destructive volcanic hazard. Quantifying the types, frequency and magnitudes of PDC events in the geological record is essential for effective risk management. However small-medium volume valley-confined PDC deposits have low preservation potential, especially when emplaced in active drainages or onto snow or ice. Where PDC deposits are preserved they can be difficult to distinguish from other surficial deposits and are frequently misinterpreted or overlooked. This is the case at Mt. Ruapehu; a much visited, high-risk active volcano in New Zealand with no historical PDCs. Through systematic field observations we identified several young proximal-medial andesitic PDC deposits exposed on Ruapehu's eastern flanks. The oldest deposits (Ohinewairua PDCs, 10km from source (South Crater) and correlates with Ruapehu's last known plinian eruption (~11.6 ka). Several younger locally preserved PDC deposits (Tukino PDCs) with denser juvenile clasts represent proximal PDCs from smaller eruptions at South Crater. Finally, a variably welded, bedded deposit containing clasts of welded spatter is interpreted to represent multiple failures of near-vent (North Ruapehu) accumulations of erupted material. Here, PDC initiation appears to have been controlled by the topographic gradient and deposition rate, without requiring a collapsing eruption column. The Ruapehu deposits highlight the limited preservation of PDC deposits, which appears to be favoured at PDC margins. Lateral and vertical flow stratification means the resulting deposits may not then represent the bulk flow. Additionally, deposit textures, distributions, and associations with moraines indicate that many of Ruapehu's PDCs encountered glacial ice during transport. This affected their distribution, mobility and preservation, and has implications for assessing the PDC hazard at Ruapehu and other glaciated volcanoes. The deposits reinforce that hazardous PDCs threatening life and

  5. The Design and Construction of a Battery Electric Vehicle Propulsion System - High Performance Electric Kart Application (United States)

    Burridge, Mark; Alahakoon, Sanath


    This paper presents an electric propulsion system designed specifically to meet the performance specification for a competition racing kart application. The paper presents the procedure for the engineering design, construction and testing of the electric powertrain of the vehicle. High performance electric Go-Kart is not an established technology within Australia. It is expected that this work will provide design guidelines for a high performance electric propulsion system with the capability of forming the basis of a competitive electric kart racing formula for Australian conditions.

  6. High-K andesite petrogenesis and crustal evolution: Evidence from mafic and ultramafic xenoliths, Egmont Volcano (Mt. Taranaki) and comparisons with Ruapehu Volcano, North Island, New Zealand (United States)

    Price, Richard C.; Smith, Ian E. M.; Stewart, Robert B.; Gamble, John A.; Gruender, Kerstin; Maas, Roland


    This study uses the geochemistry and petrology of xenoliths to constrain the evolutionary pathways of host magmas at two adjacent andesitic volcanoes in New Zealand's North Island. Egmont (Mt. Taranaki) is located on the west coast of the North Island and Ruapehu lies 140 km to the east at the southern end of the Taupo Volcanic Zone, the principal locus of subduction-related magmatism in New Zealand. Xenoliths are common in the eruptives of both volcanoes but the xenoliths suites are petrographically and geochemically different. Ruapehu xenoliths are predominantly pyroxene-plagioclase granulites derived from Mesozoic meta-greywacke basement and the underlying oceanic crust. The xenolith population of Egmont Volcano is more complex. It includes sedimentary, metamorphic and plutonic rocks from the underlying basement but is dominated by coarse grained, mafic and ultramafic igneous rocks. Gabbroic xenoliths (Group 1) are composed of plagioclase, clinopyroxene and amphibole whereas ultramafic xenoliths are dominated by amphibole (Group 2) or pyroxene (Group 3) or, in very rare cases, olivine (Group 4). In Group 1 xenoliths plagioclase and clinopyroxene and in some cases amphibole show cumulate textures. Amphibole also occurs as intercumulate poikilitic crystals or as blebs or laminae replacing pyroxene. Some Group 2 xenoliths have cumulate textures but near monomineralic amphibole xenoliths are coarse grained with bladed or comb textures. Pyroxene in Group 3 xenoliths has a polygonal granoblastic texture that is commonly overprinted by veining and amphibole replacement. Group 1 and most Group 2 xenoliths have major, trace element and Sr, Nd and Pb isotope compositions indicating affinity with the host volcanic rocks. Geochemical variation can be modelled by assimilation fractional crystallisation (AFC) and fractional crystallisation (FC) of basaltic parents assuming an assimilant with the composition of average crystalline basement and Group 1 xenoliths have


    Directory of Open Access Journals (Sweden)

    T. M. Manevich


    Full Text Available The paper presents main glaciological characteristics of present-day glaciers located on the Koryaksky volcano. The results of fieldwork (2008–2009 and high-resolution satellite image analysis let us to specify and complete information on modern glacial complex of Koryaksky volcano. Now there are seven glaciers with total area 8.36 km2. Three of them advance, two are in stationary state and one degrades. Moreover, the paper describes the new crater glacier.

  8. The tzero electric sports car : how electric vehicles can achieve both high performance and high efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, A.N.; Gage, T.B. [AC Propulsion, San Dimas, CA (United States)


    The development of a high-performance electric sports car by AC Propulsion was described along with a status report on the progress in developing the product-certified version. The development of the tzero car began in 1996. In-use testing and safety certification of prototypes is currently underway. The tzero is powered by a high-performance induction motor operated at 37 per cent higher peak current than allowed in a standard system since periods of peak power are limited to only a few seconds. The car, which can accelerate from 0 to 60 mph in 4.1 seconds, is considered to be one of the most energy-efficient cars on the road. Since the tzero will likely be sold without subsidy and since the market size for the tzero is expected to be small, in the order of 1000 units per year, it will have to be sold at a high enough price to cover the costs of small-volume production. AC Propulsion is hopeful that it may even be the first electric vehicle to be sold at a profit. Its technology and image are expected to present examples for other electric vehicles. The paper also included a comprehensive technical description of the car and its systems, such as the power electronics unit, traction converter, charger, auxiliary power supply, 12V battery, recharge interface, battery pack, battery modules and powertrain control. 4 tabs., 15 figs.

  9. High Temperature Power Converters for Military Hybrid Electric Vehicles (United States)


    M) MINI-SYMPOSIUM AUGUST 9-11 DEARBORN, MICHIGAN HIGH TEMPERATURE POWER CONVERTERS FOR MILITARY HYBRID ELECTRIC VEHICLES ABSTRACT...SUBTITLE High Temperature Power Converters for Military Hybrid Electric Vehicles 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...public release High Temperature Power Converters for Military Hybrid Electric Vehicles Page 2 of 8 I. INTRODUCTION Today, wide bandgap devices

  10. Static Electricity as Part of Electromagnetic Environment on High-Voltage Electrical Substation

    Directory of Open Access Journals (Sweden)

    M. Fursanov


    Full Text Available Causes of occurrences electrostatic discharges (ESD on high-voltage electric substation were investigated and dependences values ESD’s on parameters interaction structures, humidity of air were found. Experimental research values ESD’s on high-voltage electric substation and in man-made conditions was fulfilled. Uncertainty measurement’s was taken into consideration by research results analyze. Matching with research of other authors was made. Danger ESD’s for electric devises was established.

  11. Mahukona: The missing Hawaiian volcano

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M.O.; Muenow, D.W. (Univ. of Hawaii, Honolulu (USA)); Kurz, M.D. (Woods Hole Oceanographic Institution, MA (USA))


    New bathymetric and geochemical data indicate that a seamount west of the island of Hawaii, Mahukona, is a Hawaiian shield volcano. Mahukona has weakly alkalic lavas that are geochemically distinct. They have high {sup 3}He/{sup 4}He ratios (12-21 times atmosphere), and high H{sub 2}O and Cl contents, which are indicative of the early state of development of Hawaiian volcanoes. The He and Sr isotopic values for Mahukona lavas are intermediate between those for lavas from Loihi and Manuna Loa volcanoes and may be indicative of a temporal evolution of Hawaiian magmas. Mahukona volcano became extinct at about 500 ka, perhaps before reaching sea level. It fills the previously assumed gap in the parallel chains of volcanoes forming the southern segment of the Hawaiian hotspot chain. The paired sequence of volcanoes was probably caused by the bifurcation of the Hawaiian mantle plume during its ascent, creating two primary areas of melting 30 to 40 km apart that have persisted for at least the past 4 m.y.

  12. Kulanaokuaiki Tephra (ca, A.D. 400-1000): Newly recognized evidence for highly explosive eruptions at Kilauea Volcano, Hawai'i (United States)

    Fiske, R.S.; Rose, T.R.; Swanson, D.A.; Champion, D.E.; McGeehin, J.P.


    K??lauea may be one of the world's most intensively monitored volcanoes, but its eruptive history over the past several thousand years remains rather poorly known. Our study has revealed the vestiges of thin basaltic tephra deposits, overlooked by previous workers, that originally blanketed wide, near-summit areas and extended more than 17 km to the south coast of Hawai'i. These deposits, correlative with parts of tephra units at the summit and at sites farther north and northwest, show that K??lauea, commonly regarded as a gentle volcano, was the site of energetic pyroclastic eruptions and indicate the volcano is significantly more hazardous than previously realized. Seventeen new calibrated accelerator mass spectrometry (AMS) radiocarbon ages suggest these deposits, here named the Kulanaokuaiki Tephra, were emplaced ca. A.D. 400-1000, a time of no previously known pyroclastic activity at the volcano. Tephra correlations are based chiefly on a marker unit that contains unusually high values of TiO2 and K2O and on paleomagnetic signatures of associated lava flows, which show that the Kulanaokuaiki deposits are the time-stratigraphic equivalent of the upper part of a newly exhumed section of the Uw??kahuna Ash in the volcano's northwest caldera wall. This section, thought to have been permanently buried by rockfalls in 1983, is thicker and more complete than the previously accepted type Uw??kahuna at the base of the caldera wall. Collectively, these findings justify the elevation of the Uw??kahuna Ash to formation status; the newly recognized Kulanaokuaiki Tephra to the south, the chief focus of this study, is defined as a member of the Uw??kahuna Ash. The Kulanaokuaiki Tephra is the product of energetic pyroclastic falls; no surge- or pyroclastic-flow deposits were identified with certainty, despite recent interpretations that Uw??kahuna surges extended 10-20 km from K??lauea's summit. ?? 2009 Geological Society of America.

  13. Integration of electric drive vehicles in the Danish electricity network with high wind power penetration

    DEFF Research Database (Denmark)

    Chandrashekhara, Divya K; Østergaard, Jacob; Larsen, Esben


    /conventional) which are likely to fuel these cars. The study was carried out considering the Danish electricity network state around 2025, when the EDV penetration levels would be significant enough to have an impact on the power system. Some of the interesting findings of this study are - EDV have the potential......This paper presents the results of a study carried out to examine the feasibility of integrating electric drive vehicles (EDV) in the Danish electricity network which is characterised by high wind power penetration. One of the main aims of this study was to examine the effect of electric drive...... vehicles on the Danish electricity network, wind power penetration and electricity market. In particular the study examined the effect of electric drive vehicles on the generation capacity constraints, load curve, cross border transmission capacity and the type of generating sources (renewable...

  14. High School Students' Representations and Understandings of Electric Fields (United States)

    Cao, Ying; Brizuela, Bárbara M.


    This study investigates the representations and understandings of electric fields expressed by Chinese high school students 15 to 16 years old who have not received high school level physics instruction. The physics education research literature has reported students' conceptions of electric fields post-instruction as indicated by students'…

  15. 4D volcano gravimetry (United States)

    Battaglia, Maurizio; Gottsmann, J.; Carbone, D.; Fernandez, J.


    Time-dependent gravimetric measurements can detect subsurface processes long before magma flow leads to earthquakes or other eruption precursors. The ability of gravity measurements to detect subsurface mass flow is greatly enhanced if gravity measurements are analyzed and modeled with ground-deformation data. Obtaining the maximum information from microgravity studies requires careful evaluation of the layout of network benchmarks, the gravity environmental signal, and the coupling between gravity changes and crustal deformation. When changes in the system under study are fast (hours to weeks), as in hydrothermal systems and restless volcanoes, continuous gravity observations at selected sites can help to capture many details of the dynamics of the intrusive sources. Despite the instrumental effects, mainly caused by atmospheric temperature, results from monitoring at Mt. Etna volcano show that continuous measurements are a powerful tool for monitoring and studying volcanoes.Several analytical and numerical mathematical models can beused to fit gravity and deformation data. Analytical models offer a closed-form description of the volcanic source. In principle, this allows one to readily infer the relative importance of the source parameters. In active volcanic sites such as Long Valley caldera (California, U.S.A.) and Campi Flegrei (Italy), careful use of analytical models and high-quality data sets has produced good results. However, the simplifications that make analytical models tractable might result in misleading volcanological inter-pretations, particularly when the real crust surrounding the source is far from the homogeneous/ isotropic assumption. Using numerical models allows consideration of more realistic descriptions of the sources and of the crust where they are located (e.g., vertical and lateral mechanical discontinuities, complex source geometries, and topography). Applications at Teide volcano (Tenerife) and Campi Flegrei demonstrate the

  16. Renewable Electricity Futures Study. Volume 1: Exploration of High-Penetration Renewable Electricity Futures

    Energy Technology Data Exchange (ETDEWEB)

    Mai, T.; Wiser, R.; Sandor, D.; Brinkman, G.; Heath, G.; Denholm, P.; Hostick, D.J.; Darghouth, N.; Schlosser, A.; Strzepek, K.


    The Renewable Electricity Futures (RE Futures) Study investigated the challenges and impacts of achieving very high renewable electricity generation levels in the contiguous United States by 2050. The analysis focused on the sufficiency of the geographically diverse U.S. renewable resources to meet electricity demand over future decades, the hourly operational characteristics of the U.S. grid with high levels of variable wind and solar generation, and the potential implications of deploying high levels of renewables in the future. RE Futures focused on technical aspects of high penetration of renewable electricity; it did not focus on how to achieve such a future through policy or other measures. Given the inherent uncertainties involved with analyzing alternative long-term energy futures as well as the multiple pathways that might be taken to achieve higher levels of renewable electricity supply, RE Futures explored a range of scenarios to investigate and compare the impacts of renewable electricity penetration levels (30%-90%), future technology performance improvements, potential constraints to renewable electricity development, and future electricity demand growth assumptions. RE Futures was led by the National Renewable Energy Laboratory (NREL) and the Massachusetts Institute of Technology (MIT).

  17. Renewable Electricity Futures Study. Volume 1. Exploration of High-Penetration Renewable Electricity Futures

    Energy Technology Data Exchange (ETDEWEB)

    Hand, M. M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Baldwin, S. [U.S. Dept. of Energy, Washington, DC (United States); DeMeo, E. [Renewable Energy Consulting, Chicago, IL (United States); Reilly, J. M. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Mai, T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Arent, D. [Joint Inst. for Strategic Energy Analysis, Boulder, CO (United States); Porro, G. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Meshek, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sandor, D. [National Renewable Energy Lab. (NREL), Golden, CO (United States)


    The Renewable Electricity Futures (RE Futures) Study investigated the challenges and impacts of achieving very high renewable electricity generation levels in the contiguous United States by 2050. The analysis focused on the sufficiency of the geographically diverse U.S. renewable resources to meet electricity demand over future decades, the hourly operational characteristics of the U.S. grid with high levels of variable wind and solar generation, and the potential implications of deploying high levels of renewables in the future. RE Futures focused on technical aspects of high penetration of renewable electricity; it did not focus on how to achieve such a future through policy or other measures. Given the inherent uncertainties involved with analyzing alternative long-term energy futures as well as the multiple pathways that might be taken to achieve higher levels of renewable electricity supply, RE Futures explored a range of scenarios to investigate and compare the impacts of renewable electricity penetration levels (30%–90%), future technology performance improvements, potential constraints to renewable electricity development, and future electricity demand growth assumptions. RE Futures was led by the National Renewable Energy Laboratory (NREL) and the Massachusetts Institute of Technology (MIT). Learn more at the RE Futures website.


    Institute of Scientific and Technical Information of China (English)


    In order to improve the drivability and energy efficiency of electric vehicle (EV), more and more batteries are connected in series with high voltage which makes it necessary to monitor the electric parameters of high voltage system (HVS) to ensure the high voltage safety. A high voltage safety management system is developed to solve this critical issue. Several key electric parameters including pre-charge, contact resistance, insulation resistance and remaining capacity are monitored and analyzed based on the presented equivalent models. An electronic unit called high voltage safety controller is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated and the on-line electric parameters monitor strategy is discussed. The real vehicle experiment results indicate that the high voltage safety management system designed is suitable for EV application.

  19. Highly plastic behavior and fluidization of gouge; implications for fault and landslide mechanics and for the generation of mud volcanoes (United States)

    Shimamoto, Toshihiko; Aoki, Kazuhiro; Seshimo, Kazuyoshi; Hu, Wei; Ma, Shengli; Yao, Lu; Xiong, Ran; Xiao, Yinke


    minimum of 0.02 when the initial pore water was greater than about 30 wt%. The landslide is moving slowly at velocities to ca. 1 cm/day on a very gentle slope with a dip angle of 1 to 3 degrees, corresponding to friction coefficients of 0.02 to 0.05. Our drained tests still could not fully reproduce this landslide and we plan to conduct undrained tests as the other extreme case. Highly plastic behavior of gouge with very low friction may lead to extreme weakening of faults with dehydration, and mud volcanoes may also be caused by dramatic weakening of granular materials with abundant water. Fluidization of gouge can be an important mechanism for ultra-low friction of faults and landslide slip zones with degassing reactions or with vaporization of dehydrated water at low normal stresses. We have just made a gouge sample cell with O-rings and a pore-pressure gauge to refine those preliminary experiment, by conducting undrained tests with controlled amount of pore water while monitoring pore pressure. Additional data will be reported on those materials and on fine sandstone from a mud volcano in the Nankai Trough.

  20. Nanoscale volcanoes: accretion of matter at ion-sculpted nanopores. (United States)

    Mitsui, Toshiyuki; Stein, Derek; Kim, Young-Rok; Hoogerheide, David; Golovchenko, J A


    We demonstrate the formation of nanoscale volcano-like structures induced by ion-beam irradiation of nanoscale pores in freestanding silicon nitride membranes. Accreted matter is delivered to the volcanoes from micrometer distances along the surface. Volcano formation accompanies nanopore shrinking and depends on geometrical factors and the presence of a conducting layer on the membrane's back surface. We argue that surface electric fields play an important role in accounting for the experimental observations.

  1. [Fatal electric arc accidents due to high voltage]. (United States)

    Strauch, Hansjürg; Wirth, Ingo


    The frequency of electric arc accidents has been successfully reduced owing to preventive measures taken by the professional association. However, the risk of accidents has continued to exist in private setting. Three fatal electric arc accidents caused by high voltage are reported with reference to the autopsy findings.

  2. Plasma instabilities in high electric fields

    DEFF Research Database (Denmark)

    Morawetz, K.; Jauho, Antti-Pekka


    We analyze nonequilibrium screening with nonequilibrium Green function techniques. By employing the generalized Kadanoff-Baym ansatz to relate the correlation function to the nonequilibrium distribution function, the latter of which is assumed to be a shifted Maxwellian, an analytically tractable...... expression is derived for the nonequilibrium dielectric function epsilon(K, omega). For certain values of momenta K and frequency omega, Imepsilon(K, omega) becomes negative, implying a plasma instability. This new instability exists only for strong electric fields, underlining its nonequilibrium origin....

  3. Ultra-high Resolution Mapping of the Inner Crater of the Active Kick'em Jenny Volcano (United States)

    Hart, L.; Scott, C.; Tominaga, M.; Smart, C.; Vaughn, I.; Roman, C.; Carey, S.; German, C. R.; Participants, T.


    We conducted high-resolution geological characterization of a 0.015km^2 region of the inner crater of the most active submarine volcano in the Caribbean, Kick'em Jenny, located 8 km off Grenada in the Lesser Antilles Island Arc. We obtained digital still images and microbathymetery at an altitude of 3 m from the seafloor by using stereo cameras and a BlueView system mounted on Remotely Operated Vehicle (ROV) Hercules during the NA054 cruise on E/V Nautilus (Sept. - Oct. 2014). The seafloor images were processed to construct 2-D photo mosaics of the survey area using Standard Hercules Imaging Suite. We systematically classified the photographed seafloor geology based on the distribution of seafloor morphology and the observable rock fragment and outcrop sizes. The center of the crater floor shows a smooth, coherent texture with little variation in sea floor morphology. From immediately outside this area toward the crater rim, we observe an extensive area covered with outcrops, small rocks, and sediment: and within this area, (1) the north section is partially covered by uneven outcrops with elongated lineaments and a course, rugged seafloor with individual rock fragments observable; (2) the middle section contains high variability and heterogeneity in seafloor morphology in a non-systematic manner; and (3) overall, the southern most section displays subdued seafloor features both in space and variability compared to the other areas. The distributions of rock fragments were classified into four distinct sizes. We observe: (i) little variation in size distribution near the center of the crater floor; and (ii) rock fragment size increasing toward the rim of the crater. To obtain a better understanding of the link between variation in seafloor morphology, rock size distribution, and other in situ processes, we compare our observations on the digital photo mosaic to bathymetry data and ROV visuals (e.g. vents and bacterial mats).

  4. Global Volcano Locations Database (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NGDC maintains a database of over 1,500 volcano locations obtained from the Smithsonian Institution Global Volcanism Program, Volcanoes of the World publication. The...

  5. Mud Volcanoes Formation And Occurrence (United States)

    Guliyev, I. S.


    Mud volcanoes are natural phenomena, which occur throughout the globe. They are found at a greater or lesser scale in Azerbaijan, Turkmenistan, Georgia, on the Kerch and Taman peninsulas, on Sakhalin Island, in West Kuban, Italy, Romania, Iran, Pakistan, India, Burma, China, Japan, Indonesia, Malaysia, New Zealand, Mexico, Colombia, Trinidad and Tobago, Venezuela and Ecuador. Mud volcanoes are most well-developed in Eastern Azerbaijan, where more than 30% of all the volcanoes in the world are concentrated. More than 300 mud volcanoes have already been recognized here onshore or offshore, 220 of which lie within an area of 16,000 km2. Many of these mud volcanoes are particularly large (up to 400 m high). The volcanoes of the South Caspian form permanent or temporary islands, and numerous submarine banks. Many hypotheses have been developed regarding the origin of mud volcanoes. Some of those hypotheses will be examined in the present paper. Model of spontaneous excitation-decompaction (proposed by Ivanov and Guliev, 1988, 2002). It is supposed that one of major factors of the movement of sedimentary masses and formation of hydrocarbon deposits are phase transitions in sedimentary basin. At phase transitions there are abnormal changes of physical and chemical parameters of rocks. Abnormal (high and negative) pressure takes place. This process is called as excitation of the underground environment with periodicity from several tens to several hundreds, or thousand years. The relationship between mud volcanism and the generation of hydrocarbons, particularly methane, is considered to be a critical factor in mud volcano formation. At high flow rates the gas and sediment develops into a pseudo-liquid state and as flow increases the mass reaches the "so-called hover velocity" where mass transport begins. The mass of fluid moves as a quasi-uniform viscous mass through the sediment pile in a piston like manner until expelled from the surface as a "catastrophic eruption

  6. Development and testing of an automated High-resolution InSAR volcano-monitoring system in the MED-SUV project (United States)

    Chowdhury, Tanvir Ahmed; Minet, Christian; Fritz, Thomas; Rodriguez Gonzalez, Fernando


    Volcanic unrest which produces a variety of geological and hydrological hazards is difficult to predict. Therefore it is important to monitor volcanoes continuously. The monitoring of active volcanoes requires the reliable measurement of surface deformation before, during and after volcanic activities. Besides the improvements of the understanding of geophysical processes underlying the volcanic systems of Vesuvius/ Campi Flegrei and Mt. Etna, one of the main goals of the MED-SUV (MEDiterranean SUpersite Volcanoes) project is to design a system for automatically monitoring ground deformations over active volcanoes. Space-borne synthetic aperture radar (SAR) interferometry (InSAR), persistent scatterer interferometry (PSI) and small baseline subset algorithm (SBAS) provide powerful tools for observing the surface changes with millimeter accuracy. All the mentioned techniques address the challenges by exploiting medium to large SAR image stacks. The generation of interferometric products constitutes a major effort in terms of processing and planning. It requires a high degree of automation, robustness and quality control of the overall process. As a consequence of these requirements and constrains, the Integrated Wide Area Processor (IWAP) developed at DLR is introduced in the framework of a remote sensing task of MED-SUV project. The IWAP has been conceived and designed to optimize the processing workflow in order to minimize the processing time. Moreover, a quality control concept has been developed and integrated in the workflow. The IWAP is structured into three parts: (i) firstly, preparation of an order file containing some configuration parameters and invokes the processor; (ii) secondly, upon request from the processor, the operator performs some manual interactions by means of visual interfaces; (iii) analysis of the final product supported by extensive product visualization. This visualization supports the interpretation of the results without the need of

  7. High electric field phenomena in insulation (United States)

    Laghari, J. R.; Sarjeant, W. J.


    The present study extends previous work to include electron radiation-induced changes in monoisopropyl biphenyl (MIPB)-impregnated polypropylene film as well as the effects of neutron/gamma radiation on dry polypropylene films. Effects that were quite similar were induced by both electron and neutron radiation on the properties of interest of the polypropylene films. Impregnation of the film with MIPB had a mitigatory effect on the degradation of the properties. This report also contains the results of a simultaneous electrical and thermal aging study of a capacitor-grade polypropylene film. The data obtained in this study was fitted to models that will enable realistic prediction of lifetimes under operating conditions.

  8. Electrical system architecture having high voltage bus (United States)

    Hoff, Brian Douglas [East Peoria, IL; Akasam, Sivaprasad [Peoria, IL


    An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

  9. High spatio-temporal resolution observations of crater lake temperatures at Kawah Ijen volcano, East Java, Indonesia (United States)

    Lewicki, Jennifer L.; Caudron, Corentin; van Hinsberg, Vincent J.; Hilley, George E.


    The crater lake of Kawah Ijen volcano, East Java, Indonesia, has displayed large and rapid changes in temperature at point locations during periods of unrest, but measurement techniques employed to date have not resolved how the lake's thermal regime has evolved over both space and time. We applied a novel approach for mapping and monitoring variations in crater lake apparent surface ("skin") temperatures at high spatial (˜32 cm) and temporal (every 2 min) resolution at Kawah Ijen on 18 September 2014. We used a ground-based FLIR T650sc camera with digital and thermal infrared (TIR) sensors from the crater rim to collect (1) a set of visible imagery around the crater during the daytime and (2) a time series of co-located visible and TIR imagery at one location from pre-dawn to daytime. We processed daytime visible imagery with the Structure-from-Motion photogrammetric method to create a digital elevation model onto which the time series of TIR imagery was orthorectified and georeferenced. Lake apparent skin temperatures typically ranged from ˜21 to 33 °C. At two locations, apparent skin temperatures were ˜4 and 7 °C less than in situ lake temperature measurements at 1.5 and 5-m depth, respectively. These differences, as well as the large spatio-temporal variations observed in skin temperatures, were likely largely associated with atmospheric effects such as the evaporative cooling of the lake surface and infrared absorption by water vapor and SO2. Calculations based on orthorectified TIR imagery thus yielded underestimates of volcanic heat fluxes into the lake, whereas volcanic heat fluxes estimated based on in situ temperature measurements (68 to 111 MW) were likely more representative of Kawah Ijen in a quiescent state. The ground-based imaging technique should provide a valuable tool to continuously monitor crater lake temperatures and contribute insight into the spatio-temporal evolution of these temperatures associated with volcanic activity.

  10. A Scientific Excursion: Volcanoes. (United States)

    Olds, Henry, Jr.


    Reviews an educationally valuable and reasonably well-designed simulation of volcanic activity in an imaginary land. VOLCANOES creates an excellent context for learning information about volcanoes and for developing skills and practicing methods needed to study behavior of volcanoes. (Author/JN)

  11. Energy efficiency indicators for high electric-load buildings

    Energy Technology Data Exchange (ETDEWEB)

    Aebischer, Bernard; Balmer, Markus A.; Kinney, Satkartar; Le Strat, Pascale; Shibata, Yoshiaki; Varone, Frederic


    Energy per unit of floor area is not an adequate indicator for energy efficiency in high electric-load buildings. For two activities, restaurants and computer centres, alternative indicators for energy efficiency are discussed.

  12. High Alumina Refractory Bricks for Electric Arc Furnace Roofs

    Institute of Scientific and Technical Information of China (English)


    @@ 1 Scope This standard specifies the sort, technical requirement, test method, inspection rules, marking, packing, transportation, storage and quality certification of high alumina refractory bricks for electric arc furnace roofs.

  13. From high quality seismic data acquisition in remote volcanic area to fast data distribution to scientific community: The UnderVolc project on Piton de la Fournaise volcano (United States)

    Brenguier, Florent; Kowalski, Philippe; Pequegnat, Catherine; Lauret, Frédéric; Cougoulat, Glenn; Boissier, Patrice; Catherine, Philippe


    Piton de la Fournaise basaltic volcano (La Réunion island, France) is one of the most active volcano in the world with an average of one eruption every year. This volcano is thus an ideal case study for research projects focusing on studying magmatic, seismic and deformation processes occurring in volcanic areas. The UNDERVOLC (UNDERstanding VOLCanic Processes) research project main goal is to provide high quality 3-component broadband continuous seismic data to an amount of about 30 volcano-seismologists from different international research teams (including Japan and New-Zealand). This data acquisition system is moreover dedicated to the monitoring of Piton de la Fournaise volcano by providing real-time seismic data to the Piton de la Fournaise volcanological Observatory/IPGP. The network consists of 21 fully autonomous stations composed of CMG40-T seismometers associated to high dynamic digitizers and linked to wireless digital radio stations. The seismic signal is sent by UDP protocol to the observatory through a network of wireless LAN over large distances (~10 km) and possibly through the internet to the Observatory. The acquisition system at the observatory is composed of: 1-An Earthworm system (USGS - ISTI - CERI) with a Q330 to Earthworm data acquisition module (6 permanent stations from the observatory) 2-An Apollo server system (Nanometrics) for 15 stations (for which seismometers and digitizers belong to the French national pool of portable seismic instruments Sismob, INSU-CNRS) In both case, requests are sent back to the stations in case of loss of udp packets. This system allows us producing miniseed files every hour. Since September 2009, the full dataset has less then 1 % of gaps. In order to provide a fast data access to the scientific community, we synchronize our dataset every night with the SISMOB datacenter located in France (LGIT, Grenoble). After a quality check, seed data volumes are produced and distributed by standard NETDC requests from

  14. High-tension Electrical Burns: Report of Two Cases


    Abbas, A.D.; Dabkana, T.M.; Tahir, C.; Naaya, H.U.


    High-tension electrical burns are a rare but devastating form of injury. The objective of this case report is to bring to the fore the severity of this rare form of injury and highlight the benefits of active surgical management of such a condition. We report the cases of two patients who were managed for high-tension electrical burns and highlight the main features of their presentation and management. Both patients needed urgent resuscitation and subsequent multiple amputations and disartic...

  15. Remote Sensing of Active Volcanoes (United States)

    Francis, Peter; Rothery, David

    The synoptic coverage offered by satellites provides unparalleled opportunities for monitoring active volcanoes, and opens new avenues of scientific inquiry. Thermal infrared radiation can be used to monitor levels of activity, which is useful for automated eruption detection and for studying the emplacement of lava flows. Satellite radars can observe volcanoes through clouds or at night, and provide high-resolution topographic data. In favorable conditions, radar inteferometery can be used to measure ground deformation associated with eruptive activity on a centimetric scale. Clouds from explosive eruptions present a pressing hazard to aviation; therefore, techniques are being developed to assess eruption cloud height and to discriminate between ash and meterological clouds. The multitude of sensors to be launched on future generations of space platforms promises to greatly enhance volcanological studies, but a satellite dedicated to volcanology is needed to meet requirements of aviation safety and volcano monitoring.

  16. ASTER Urgent Response to the 2006 Eruption of Augustine Volcano, Alaska: Science and Decision Support Gained From Frequent High-resolution, Satellite Thermal Infrared Imaging of Volcanic Events (United States)

    Wessels, R. L.; Ramsey, M. S.; Schneider, D. S.; Coombs, M.; Dehn, J.; Realmuto, V. J.


    Augustine Volcano, Alaska explosively erupted on January 11, 2006 after nearly eight months of increasing seismicity, deformation, gas emission, and small phreatic explosions. The volcano produced a total of 13 explosive eruptions during the last three weeks of January 2006. A new summit lava dome and two short, blocky lava flows grew during February and March 2006. A series of 7 daytime and 15 nighttime Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) scenes were acquired in response to this new activity. This response was facilitated by a new ASTER Urgent Request Protocol system. The ASTER data provided several significant observations as a part of a much larger suite of real-time or near-real-time data from other satellite (AVHRR, MODIS), airborne (FLIR, visual, gas), and ground-based (seismometers, radiometers) sensors used at the Alaska Volcano Observatory (AVO). ASTER is well-suited to volcanic observations because of its 15-m to 90-m spatial resolution, its ability to be scheduled and point off-nadir, and its ability to collect visible-near infrared (VNIR) to thermal infrared (TIR) data during both the day and night. Aided by the volcano's high latitude (59.4°N) ASTER was able to provide frequent repeat imaging as short as one day between scenes with an average 6-day repeat during the height of activity. These data provided a time series of high-resolution VNIR, shortwave infrared (SWIR - detects temperatures from about 200°C to > 600°C averaged over a 30-m pixel), and TIR (detects temperatures up to about 100°C averaged over a 90-m pixel) data of the volcano and its eruptive products. Frequent satellite imaging of volcanoes is necessary to record rapid changes in activity and to avoid recurring cloud cover. Of the 22 ASTER scenes acquired between October 30, 2005 and May 30, 2006, the volcano was clear to partly cloudy in 13 scenes. The most useful pre-eruption ASTER Urgent Request image was acquired on December 20. These data

  17. High water contents in basaltic melt inclusions from Arenal volcano, Costa Rica (United States)

    Wade, J. A.; Plank, T.; Hauri, E. H.; Melson, W. G.; Soto, G. J.


    Despite the importance of water to arc magma genesis, fractionation and eruption, few quantitative constraints exist on the water content of Arenal magmas. Early estimates, by electron microprobe sum deficit, suggested up to 4 wt% H2O in olivine-hosted basaltic andesite melt inclusions (MI) from pre-historic ET-6 tephra (Melson, 1982), and up to 7 wt% H2O in plagioclase and orthopyroxene-hosted dacitic MI from 1968 lapilli (Anderson, 1979). These high water contents are consistent with abundant hornblende phenocrysts in Arenal volcanics, but inconsistent with geochemical tracers such as 10Be and Ba/La that suggest a low flux of recycled material (and presumably water) from the subduction zone. In order to test these ideas, and provide the first direct measurements of water in mafic Arenal magmas, we have studied olivine-hosted MI from the prehistoric (900 yBP; Soto et al., 1998) ET3 tephra layer. MI range from andesitic (> 58% SiO2) to basaltic compositions ( 4 wt%) found here for Arenal basaltic MI support the semi-quantitative data from earlier studies, but are somewhat unexpected given predictions from slab tracers. Arenal water contents (4%) approach those of the 1995 eruption of Cerro Negro in Nicaragua (4-5 wt% in basaltic MI; Roggensack et al., 1997), despite the fact that the latter has Ba/La of > 100, while Arenal has Ba/La Boletin de Volcanologia; Roggensack et al. (1997) Science; Soto et al. (1998) OSIVAM; Williams-Jones et al. (2001) Journal of Volc. and Geoth. Res.

  18. High Torque, Direct Drive Electric Motor Project (United States)

    National Aeronautics and Space Administration — Bear Engineering proposes to advance the development of an innovative high torque, low speed, direct drive motor in order to meet NASA's requirements for such...

  19. High Torque, Direct Drive Electric Motor Project (United States)

    National Aeronautics and Space Administration — Bear Engineering proposes to develop an innovative high torque, low speed, direct drive motor in order to meet NASA's requirements for such devices. Fundamentally,...

  20. Electric rail gun projectile acceleration to high velocity (United States)

    Bauer, D. P.; Mccormick, T. J.; Barber, J. P.


    Electric rail accelerators are being investigated for application in electric propulsion systems. Several electric propulsion applications require that the rail accelerator be capable of launching projectiles at velocities above 10 km/s. An experimental program was conducted to develop rail accelerator technology for high velocity projectile launch. Several 6 mm bore, 3 m long rail accelerators were fabricated. Projectiles with a mass of 0.2 g were accelerated by plasmas, carrying currents up to 150 kA. Experimental design and results are described. Results indicate that the accelerator performed as predicted for a fraction of the total projectile acceleration. The disparity between predicted and measured results are discussed.

  1. High Dynamic Range Electric Field Sensor for Electromagnetic Pulse Detection

    CERN Document Server

    Lin, Che-Yun; Lee, Beom Suk; Zhang, Xingyu; Chen, Ray T


    We design a high dynamic range electric field sensor based on domain inverted electro-optic (E-O) polymer Y-fed directional coupler for electromagnetic wave detection. This electrode-less, all optical, wideband electrical field sensor is fabricated using standard processing for E-O polymer photonic devices. Experimental results demonstrate effective detection of electric field from 16.7V/m to 750KV/m at a frequency of 1GHz, and spurious free measurement range of 70dB.

  2. Italian Volcano Supersites (United States)

    Puglisi, G.


    Volcanic eruptions are among the geohazards that may have a substantial economic and social impact, even at worldwide scale. Large populated regions are prone to volcanic hazards worldwide. Even local phenomena may affect largely populated areas and in some cases even megacities, producing severe economic losses. On a regional or global perspective, large volcanic eruptions may affect the climate for years with potentially huge economic impacts, but even relatively small eruptions may inject large amounts of volcanic ash in the atmosphere and severely affect air traffic over entire continents. One of main challenges of the volcanological community is to continuously monitor and understand the internal processes leading to an eruption, in order to give substantial contributions to the risk reduction. Italian active volcanoes constitute natural laboratories and ideal sites where to apply the cutting-edge volcano observation systems, implement new monitoring systems and to test and improve the most advanced models and methods for investigate the volcanic processes. That's because of the long tradition of volcanological studies resulting into long-term data sets, both in-situ and from satellite systems, among the most complete and accurate worldwide, and the large spectrum of the threatening volcanic phenomena producing high local/regional/continental risks. This contribution aims at presenting the compound monitoring systems operating on the Italian active volcanoes, the main improvements achieved during the recent studies direct toward volcanic hazard forecast and risk reductions and the guidelines for a wide coordinated project aimed at applying the ideas of the GEO Supersites Initiative at Mt. Etna and Campi Flegrei / Vesuvius areas.

  3. Fabrication of highly conductive carbon nanotube fibers for electrical application (United States)

    Guo, Fengmei; Li, Can; Wei, Jinquan; Xu, Ruiqiao; Zhang, Zelin; Cui, Xian; Wang, Kunlin; Wu, Dehai


    Carbon nanotubes (CNTs) have great potential for use as electrical wires because of their outstanding electrical and mechanical properties. Here, we fabricate lightweight CNT fibers with electrical conductivity as high as that of stainless steel from macroscopic CNT films by drawing them through diamond wire-drawing dies. The entangled CNT bundles are straightened by suffering tension, which improves the alignment of the fibers. The loose fibers are squeezed by the diamond wire-drawing dies, which reduces the intertube space and contact resistance. The CNT fibers prepared by drawing have an electrical conductivity as high as 1.6 × 106 s m-1. The fibers are very stable when kept in the air and under cyclic tensile test. A prototype of CNT motor is demonstrated by replacing the copper wires with the CNT fibers.

  4. High spatio-temporal resolution observations of crater-lake temperatures at Kawah Ijen volcano, East Java, Indonesia (United States)

    Lewicki, Jennifer L.; Corentin Caudron,; Vincent van Hinsberg,; George Hilley,


    The crater lake of Kawah Ijen volcano, East Java, Indonesia, has displayed large and rapid changes in temperature at point locations during periods of unrest, but measurement techniques employed to-date have not resolved how the lake’s thermal regime has evolved over both space and time. We applied a novel approach for mapping and monitoring variations in crater-lake apparent surface (“skin”) temperatures at high spatial (~32 cm) and temporal (every two minutes) resolution at Kawah Ijen on 18 September 2014. We used a ground-based FLIR T650sc camera with digital and thermal infrared (TIR) sensors from the crater rim to collect (1) a set of visible imagery around the crater during the daytime and (2) a time series of co-located visible and TIR imagery at one location from pre-dawn to daytime. We processed daytime visible imagery with the Structure-from-Motion photogrammetric method to create a digital elevation model onto which the time series of TIR imagery was orthorectified and georeferenced. Lake apparent skin temperatures typically ranged from ~21 to 33oC. At two locations, apparent skin temperatures were ~ 4 and 7 oC less than in-situ lake temperature measurements at 1.5 and 5 m depth, respectively. These differences, as well as the large spatio-temporal variations observed in skin temperatures, were likely largely associated with atmospheric effects such as evaporative cooling of the lake surface and infrared absorption by water vapor and SO2. Calculations based on orthorectified TIR imagery thus yielded underestimates of volcanic heat fluxes into the lake, whereas volcanic heat fluxes estimated based on in-situ temperature measurements (68 to 111 MW) were likely more representative of Kawah Ijen in a quiescent state. The ground-based imaging technique should provide a valuable tool to continuously monitor crater-lake temperatures and contribute insight into the spatio-temporal evolution of these temperatures associated with volcanic activity.

  5. Volcanoes: Nature's Caldrons Challenge Geochemists. (United States)

    Zurer, Pamela S.


    Reviews various topics and research studies on the geology of volcanoes. Areas examined include volcanoes and weather, plate margins, origins of magma, magma evolution, United States Geological Survey (USGS) volcano hazards program, USGS volcano observatories, volcanic gases, potassium-argon dating activities, and volcano monitoring strategies.…

  6. Preliminary volcano-hazard assessment for Augustine Volcano, Alaska (United States)

    Waythomas, Christopher F.; Waitt, Richard B.


    Augustine Volcano is a 1250-meter high stratovolcano in southwestern Cook Inlet about 280 kilometers southwest of Anchorage and within about 300 kilometers of more than half of the population of Alaska. Explosive eruptions have occurred six times since the early 1800s (1812, 1883, 1935, 1964-65, 1976, and 1986). The 1976 and 1986 eruptions began with an initial series of vent-clearing explosions and high vertical plumes of volcanic ash followed by pyroclastic flows, surges, and lahars on the volcano flanks. Unlike some prehistoric eruptions, a summit edifice collapse and debris avalanche did not occur in 1812, 1935, 1964-65, 1976, or 1986. However, early in the 1883 eruption, a portion of the volcano summit broke loose forming a debris avalanche that flowed to the sea. The avalanche initiated a small tsunami reported on the Kenai Peninsula at English Bay, 90 kilometers east of the volcano. Plumes of volcanic ash are a major hazard to jet aircraft using Anchorage International and other local airports. Ashfall from future eruptions could disrupt oil and gas operations and shipping activities in Cook Inlet. Eruptions similar to the historical and prehistoric eruptions are likely in Augustine's future.

  7. High school students' representations and understandings of electric fields (United States)

    Cao, Ying; Brizuela, Bárbara M.


    This study investigates the representations and understandings of electric fields expressed by Chinese high school students 15 to 16 years old who have not received high school level physics instruction. The physics education research literature has reported students' conceptions of electric fields postinstruction as indicated by students' performance on textbook-style questions. It has, however, inadequately captured student ideas expressed in other situations yet informative to educational research. In this study, we explore students' ideas of electric fields preinstruction as shown by students' representations produced in open-ended activities. 92 participant students completed a worksheet that involved drawing comic strips about electric charges as characters of a cartoon series. Three students who had spontaneously produced arrow diagrams were interviewed individually after class. We identified nine ideas related to electric fields that these three students spontaneously leveraged in the comic strip activity. In this paper, we describe in detail each idea and its situated context. As most research in the literature has understood students as having relatively fixed conceptions and mostly identified divergences in those conceptions from canonical targets, this study shows students' reasoning to be more variable in particular moments, and that variability includes common sense resources that can be productive for learning about electric fields.

  8. Effects of high external electric fields on protein conformation (United States)

    Pompa, Pier Paolo; Bramanti, Alessandro; Maruccio, Giuseppe; del Mercato, Loretta Laureana; Chiuri, Rocco; Cingolani, Roberto; Rinaldi, Ross


    Resistance of biomolecules to high electric fields is a main concern for nanobioelectronics/nanobiosensing applications, and it is also a relevant issue from a fundamental perspective, to understand the dielectric properties and structural dynamics of proteins. In nanoscale devices, biomolecules may experience electric fields as high as 107 V/m in order to elicit charge transport/transfer. Understanding the effects of such fields on their structural integrity is thus crucial to assess the reliability of biomolecular devices. In this study, we show experimental evidence for the retention of native-like fold pattern by proteins embedded in high electric fields. We have tested the metalloprotein azurin, deposited onto SiO2 substrates in air with proper electrode configuration, by applying high static electric fields (up to 106-107 V/m). The effects on the conformational properties of protein molecules have been determined by means of intrinsic fluorescence measurements. Experimental results indicate that no significant field-induced conformational alteration occurs. This behavior is also discussed and supported by theoretical predictions of the intrinsic intra-protein electric fields. As the general features of such inner fields are not peculiar of azurin, the conclusions presented here should have general validity.

  9. Electrical Resistivity and Thermodynamic Properties of Iron Under High Pressure (United States)

    Hieu, Ho Khac; Hai, Tran Thi; Hong, Nguyen Thi; Sang, Ngo Dinh; Tuyen, Nguyen Viet


    In this work, the electrical resistivity and thermodynamic properties of iron under high pressure have been investigated by using the semi-empirical approach. The recently well-established Grüneisen parameter expressions have been applied to derive the Debye frequency and temperature under compression. Using these results combined with the Bloch-Grüneisen law, the resistivity of iron has also been determined up to Earth's core pressures. We show that the electrical resistivity diminished gradually with pressure and saturates at high pressure. Our model gives low electrical resistivity values which are in agreement with the recent experimental measurements. The low resistivity may be attributed to the well-known resistivity saturation effect at high temperature, which was not considered in earlier models of core conductivity.

  10. Turkey's High Temperature Geothermal Energy Resources and Electricity Production Potential (United States)

    Bilgin, Ö.


    Turkey is in the first 7 countries in the world in terms of potential and applications. Geothermal energy which is an alternative energy resource has advantages such as low-cost, clean, safe and natural resource. Geothermal energy is defined as hot water and steam which is formed by heat that accumulated in various depths of the Earth's crust; with more than 20oC temperature and which contain more than fused minerals, various salts and gases than normal underground and ground water. It is divided into three groups as low, medium and high temperature. High-temperature fluid is used in electricity generation, low and medium temperature fluids are used in greenhouses, houses, airport runways, animal farms and places such as swimming pools heating. In this study high temperature geothermal fields in Turkey which is suitable for electricity production, properties and electricity production potential was investigated.

  11. Electric Insulation Detection Method for High-voltage Insulators

    Directory of Open Access Journals (Sweden)

    Wang Jiajun


    Full Text Available The principle of partial discharge detection is that through partial bridged discharge under high voltage electric field, it detects the inner air-filled cavity of high-voltage insulators. And it is a nondestructive detection method based on discharge magnitude to judge the insulation quality. The detecting system that adopts the partial discharge detection is more rigorous than testing system for electricity products, which must have small discharge capacity and higher sensitivity. This paper describes the principles of partial discharge detection and analysis insulation detection.

  12. Electric propulsion - A high energy capability for solar system exploration (United States)

    Atkins, K. L.


    The principles of spacecraft electric (ion thruster) propulsion are briefly reviewed. Attention is given to the inner and outer planet applications of electric (and solar electric) propulsion. Electric propulsion is considered as a stepping stone to nuclear electric propulsion.

  13. Foci of Volcanoes

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, I.


    One may assume a center of volcanic activities beneath the edifice of an active volcano, which is here called the focus of the volcano. Sometimes it may be a ''magma reservoir''. Its depth may differ with types of magma and change with time. In this paper, foci of volcanoes are discussed from the viewpoints of four items: (1) Geomagnetic changes related with volcanic activities; (2) Crustal deformations related with volcanic activities; (3) Magma transfer through volcanoes; and (4) Subsurface structure of calderas.

  14. Magnetospheric effects in atmospheric electricity at high latitudes (United States)

    Shumilov, O. I.; Kasatkina, E. A.; Frank-Kamenetsky, A. V.; Raspopov, O. M.; Vasiljev, A. N.; Struev, A. G.


    Measurements of the vertical atmospheric electric field (Ez) made at auroral station Apatity (geomagnetic latitude: 63.8) and polar cap station Vostok, Antarctica (geomagnetic latitude: -89.3) in 2001-2002 have been analyzed. The measurements were made by a high-latitude computer-aided complex installed at Apatity in 2001. It consists of three spatially placed microbarographs for measurements of atmospheric waves, a device for air conductivity measurement and a device for measurement of vertical component of the atmospheric electric field. The computer-aided system permits to get information with a frequency of five times per second. The ground level atmospheric electric field was found to have systematic local diurnal and seasonal variations. Diurnal variations of atmospheric potential gradient were found to have a departure from the Carnegie curve. A distinct difference in the diurnal variation of atmospheric electric field has been observed also between disturbed (Kp>30) and extremely quiet (Kplatitude electric field variations appear to be the result of solar wind-magnetosphere-ionosphere coupling. Besides, we have found the similarity between the diurnal course of the atmospheric electric field under the quiet geomagnetic conditions and the diurnal variation of galactic cosmic rays. These results have been explained in terms of calculated effective Bz component of the interpalnetary magnetic field arising due to variation of the geomagnetic dipole axis inclination during the Earth's rotation. The results of analysis of the influence of extreme weather conditions (rain, snow, snowstorm, stormclouds, thunderstorms, lightning) on atmospheric electricity (electric field and conductivity) are also discussed. This work was supported by EC (grant INTAS 97-31008) and RFBR (grant 01-05-64850).

  15. High School Students' Understandings and Representations of the Electric Field

    CERN Document Server

    Cao, Ying


    This study investigates the understandings and representations of the electric field expressed by Chinese high school students ages 15 to 16 who have not yet received high school-level physics instruction. The literature has reported students' ideas of the electric field post-instruction as indicated by their performance on textbook-style questionnaires. However, by relying on measures such as questionnaires, previous research has inadequately captured the thinking process that led students to answer questions in the ways that they did. The present study portrays the beginning of this process by closely examining students' understandings pre-instruction. The participants in this study were asked to engage in a lesson that included informal group tasks that involved playing a Web-based hockey game that replicated an electric field and drawing comic strips that used charges as characters. The lesson was videotaped, students' work was collected, and three students were interviewed afterward to ascertain more det...

  16. LCA of electricity systems with high wind power penetration

    DEFF Research Database (Denmark)

    Turconi, Roberto; O' Dwyer, C. O.; Flynn, D.

    Electricity systems are shifting from being based on fossil fuels towards renewable sources to enhance energy security and mitigate climate change. However, by introducing high shares of variable renewables - such as wind and solar - dispatchable power plants are required to vary their output...... to fulfill the remaining electrical demand, potentially increasing their environmental impacts [1,2]. In this study the environmental impacts of potential short-term future electricity systems in Ireland with high shares of wind power (35-50% of total installed capacity) were evaluated using life cycle...... considered: while not outweighing the benefits from increasing wind energy, cycling emissions are not negligible and should thus be systematically included (i.e. by using emission factors per unit of fuel input rather than per unit of power generated). Cycling emissions increased with the installed wind...

  17. Confined surface plasmon sensors based on strongly coupled disk-in-volcano arrays. (United States)

    Ai, Bin; Wang, Limin; Möhwald, Helmuth; Yu, Ye; Zhang, Gang


    Disk-in-volcano arrays are reported to greatly enhance the sensing performance due to strong coupling in the nanogaps between the nanovolcanos and nanodisks. The designed structure, which is composed of a nanovolcano array film and a disk in each cavity, is fabricated by a simple and efficient colloidal lithography method. By tuning structural parameters, the disk-in-volcano arrays show greatly enhanced resonances in the nanogaps formed by the disks and the inner wall of the volcanos. Therefore they respond to the surrounding environment with a sensitivity as high as 977 nm per RIU and with excellent linear dependence on the refraction index. Moreover, through mastering the fabrication process, biological sensing can be easily confined to the cavities of the nanovolcanos. The local responsivity has the advantages of maximum surface plasmon energy density in the nanogaps, reducing the sensing background and saving expensive reagents. The disk-in-volcano arrays also possess great potential in applications of optical and electrical trapping and single-molecule analysis, because they enable establishment of electric fields across the gaps.

  18. Behavior of Rubber Materials under Exposure to High Electric Fields

    DEFF Research Database (Denmark)

    Candela Garolera, Anna; Holbøll, Joachim; Henriksen, M,


    The effect of high electrical stress on rubber materials is investigated by performing breakdown tests and tracking resistance tests on selected samples. The study is focused on the relationship between the dielectric strength and the thickness of the samples, as well as the influence of the inte...

  19. Atmospheric Electric Field Measurements at 100 Hz and High Frequency Electric Phenomena (United States)

    Conceição, Ricardo; Gonçalves da Silva, Hugo; Matthews, James; Bennett, Alec; Chubb, John


    Spectral response of Atmospheric Electric Potential Gradient (PG), symmetric to the Atmospheric Electric Field, gives important information about phenomena affecting these measurements with characteristic time-scales that appear in the spectra as specific periodicities. This is the case of urban pollution that has a clear weekly dependence and reveals itself on PG measurements by a ~7 day periodicity (Silva et al., 2014). While long-term time-scales (low frequencies) have been exhaustively explored in literature, short-term time-scales (high frequencies), above 1 Hz, have comparatively received much less attention (Anisimov et al., 1999). This is mainly because of the technical difficulties related with the storage of such a huge amount of data (for 100 Hz sampling two days of data uses a ~1 Gb file) and the response degradation of the field-meters at such frequencies. Nevertheless, important Electric Phenomena occurs for frequencies above 1 Hz that are worth pursuing, e.g. the Schumann Resonances have a signature of worldwide thunderstorm activity at frequencies that go from ~8 up to ~40 Hz. To that end the present work shows preliminary results on PG measurements at 100 Hz that took place on two clear-sky days (17th and 18th June 2015) on the South of Portugal, Évora (38.50° N, 7.91° W). The field-mill used is a JCI 131F installed in the University of Évora campus (at 2 m height) with a few trees and two buildings in its surroundings (~50 m away). This device was developed by John Chubb (Chubb, 2014) and manufactured by Chilworth (UK). It was calibrated in December 2013 and recent work by the author (who is honored in this study for his overwhelming contribution to atmospheric electricity) reveals basically a flat spectral response of the device up to frequencies of 100 Hz (Chubb, 2015). This makes this device suitable for the study of High Frequency Electric Phenomena. Anisimov, S.V., et al. (1999). On the generation and evolution of aeroelectric structures

  20. Soufriere Hills Volcano (United States)


    In this ASTER image of Soufriere Hills Volcano on Montserrat in the Caribbean, continued eruptive activity is evident by the extensive smoke and ash plume streaming towards the west-southwest. Significant eruptive activity began in 1995, forcing the authorities to evacuate more than 7,000 of the island's original population of 11,000. The primary risk now is to the northern part of the island and to the airport. Small rockfalls and pyroclastic flows (ash, rock and hot gases) are common at this time due to continued growth of the dome at the volcano's summit.This image was acquired on October 29, 2002 by the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) on NASA's Terra satellite. With its 14 spectral bands from the visible to the thermal infrared wavelength region, and its high spatial resolution of 15 to 90 meters (about 50 to 300 feet), ASTER images Earth to map and monitor the changing surface of our planet.ASTER is one of five Earth-observing instruments launched December 18, 1999, on NASA's Terra satellite. The instrument was built by Japan's Ministry of Economy, Trade and Industry. A joint U.S./Japan science team is responsible for validation and calibration of the instrument and the data products.The broad spectral coverage and high spectral resolution of ASTER will provide scientists in numerous disciplines with critical information for surface mapping, and monitoring of dynamic conditions and temporal change. Example applications are: monitoring glacial advances and retreats; monitoring potentially active volcanoes; identifying crop stress; determining cloud morphology and physical properties; wetlands evaluation; thermal pollution monitoring; coral reef degradation; surface temperature mapping of soils and geology; and measuring surface heat balance.Dr. Anne Kahle at NASA's Jet Propulsion Laboratory, Pasadena, California, is the U.S. Science team leader; Bjorn Eng of JPL is the project manager. The Terra mission is part of NASA

  1. High-frequency electric field amplification in a magnetized plasma

    Energy Technology Data Exchange (ETDEWEB)

    Timofeev, Aleksandr V [Russian Research Centre ' Kurchatov Institute' , Moscow (Russian Federation)


    In the investigation of cyclotron ion heating in systems designed for plasma isotope separation, the high-frequency (HF) electric field amplification effect was found to occur in equilibrium plasma. In the present article this effect is treated as a result of the interaction of the plasma placed in a constant external magnetic field with the HF modes of the vacuum chamber. Consistent elaboration of this approach allowed obtaining a clear interpretation of the HF electric field amplification effect and constructing a simple model of HF field excitation in a plasma column embedded in the external magnetic field. (methodological notes)

  2. Instrumentation Recommendations for Volcano Monitoring at U.S. Volcanoes Under the National Volcano Early Warning System (United States)

    Moran, Seth C.; Freymueller, Jeff T.; LaHusen, Richard G.; McGee, Kenneth A.; Poland, Michael P.; Power, John A.; Schmidt, David A.; Schneider, David J.; Stephens, George; Werner, Cynthia A.; White, Randall A.


    midlatitude or high-latitude volcanoes; (c) safety factors during unrest, which can limit where new instrumentation can safely be installed (particularly at near-vent sites that can be critical for precursor detection and eruption forecasting); and (d) the remoteness of many U.S. volcanoes (particularly those in the Aleutians and the Marianas Islands), where access is difficult or impossible most of the year. Given these difficulties, it is reasonable to anticipate that ground-based monitoring of eruptions at U.S. volcanoes will likely be performed primarily with instruments installed before unrest begins. 2. Given a growing awareness of previously undetected 2. phenomena that may occur before an eruption begins, at present the types and (or) density of instruments in use at most U.S. volcanoes is insufficient to provide reliable early warning of volcanic eruptions. As shown by the gap analysis of Ewert and others (2005), a number of U.S. volcanoes lack even rudimentary monitoring. At those volcanic systems with monitoring instrumentation in place, only a few types of phenomena can be tracked in near-real time, principally changes in seismicity, deformation, and large-scale changes in thermal flux (through satellite-based remote sensing). Furthermore, researchers employing technologically advanced instrumentation at volcanoes around the world starting in the 1990s have shown that subtle and previously undetectable phenomena can precede or accompany eruptions. Detection of such phenomena would greatly improve the ability of U.S. volcano observatories to provide accurate early warnings of impending eruptions, and is a critical capability particularly at the very high-threat volcanoes identified by Ewert and others (2005). For these two reasons, change from a reactive to a proactive volcano-monitoring strategy is clearly needed at U.S. volcanoes. Monitoring capabilities need to be expanded at virtually every volcanic center, regardless of its current state of

  3. Electrical conductivity of rigid polyurethane foam at high temperature (United States)

    Johnson, R. T., Jr.


    The electrical conductivity of rigid polyurethane foam, used for electronic encapsulation, was measured during thermal decomposition to 3400 C. At higher temperatures the conductance continues to increase. With pressure loaded electrical leads, sample softening results in eventual contact between electrodes which produces electrical shorting. Air and nitrogen environments show no significant dependence of the conductivity on the atmosphere over the temperature range. The insulating characteristics of polyurethane foam below approx. 2700 C are similar to those for silicone based materials used for electronic case housings and are better than those for phenolics. At higher temperatures (greater than or equal to 2700 C) the phenolics appear to be better insulators to approx. 5000 C and the silicones to approx. 6000 C. It is concluded that the Sylgard 184/GMB encapsulant is a significantly better insulator at high temperature than the rigid polyurethane foam.

  4. Design of a 200kW electric powertrain for a high performance electric vehicle

    Directory of Open Access Journals (Sweden)

    Wilmar Martinez


    Full Text Available With the purpose of designing the electric powertrain of a high performance electric vehicle capable of running a quarter mile in 10 seconds, firstly it is necessary to calculate the required energy, torque, and power in order to size and select the suitable storage components and electric motors. Secondly, an assessment of the powertrain arrangement is needed to choose the best internal configuration of the vehicle and guarantee the highest efficiency possible. Finally, a design of the power conversion stages, specifically the DC-DC converter that interfaces the storage unit with the electric motors, is required as well. This paper shows the energy calculation procedure based on a longitudinal dynamic model of the vehicle and the selection method of the storage components and motors needed for this application, as well as the design of two 100kW interleaved boost converters with coupled inductors. In addition, a novel operation of the interleaved boost converter is proposed in order to increase the efficiency of the converter. As a result, the designed converter achieved a power density of 24,2kW/kg with an efficiency of 98 %, which was validated by experimental tests of a low power prototype.

  5. Evaluation of High-Performance Space Nuclear Electric Generators for Electric Propulsion Application (United States)

    Woodcock, Gordon; Kross, Dennis A. (Technical Monitor)


    Electric propulsion applications are enhanced by high power-to-mass ratios for their electric power sources. At multi-megawatt levels, we can expect thrust production systems to be less than 5 kg/kWe. Application of nuclear electric propulsion to human Mars missions becomes an attractive alternative to nuclear thermal propulsion if the propulsion system is less than about 10 kg/kWe. Recent references have projected megawatt-plus nuclear electric sources at specific mass values from less than 1 kg/kWe to about 5 kg/kWe. Various assumptions are made regarding power generation cycle (turbogenerator; MHD (magnetohydrodynamics)) and reactor heat source design. The present paper compares heat source and power generation options on the basis of a parametric model that emphasizes heat transfer design and realizable hardware concept. Pressure drop (important!) is included in the power cycle analysis, and MHD and turbogenerator cycles are compared. Results indicate that power source specific mass less than 5 kg/kWe is attainable, even if peak temperatures achievable are limited to 1500 K. Projections of specific mass less than 1 kg/kWe are unrealistic, even at the highest peak temperatures considered.

  6. High-throughput electrical characterization for robust overlay lithography control (United States)

    Devender, Devender; Shen, Xumin; Duggan, Mark; Singh, Sunil; Rullan, Jonathan; Choo, Jae; Mehta, Sohan; Tang, Teck Jung; Reidy, Sean; Holt, Jonathan; Kim, Hyung Woo; Fox, Robert; Sohn, D. K.


    Realizing sensitive, high throughput and robust overlay measurement is a challenge in current 14nm and advanced upcoming nodes with transition to 300mm and upcoming 450mm semiconductor manufacturing, where slight deviation in overlay has significant impact on reliability and yield1). Exponentially increasing number of critical masks in multi-patterning lithoetch, litho-etch (LELE) and subsequent LELELE semiconductor processes require even tighter overlay specification2). Here, we discuss limitations of current image- and diffraction- based overlay measurement techniques to meet these stringent processing requirements due to sensitivity, throughput and low contrast3). We demonstrate a new electrical measurement based technique where resistance is measured for a macro with intentional misalignment between two layers. Overlay is quantified by a parabolic fitting model to resistance where minima and inflection points are extracted to characterize overlay control and process window, respectively. Analyses using transmission electron microscopy show good correlation between actual overlay performance and overlay obtained from fitting. Additionally, excellent correlation of overlay from electrical measurements to existing image- and diffraction- based techniques is found. We also discuss challenges of integrating electrical measurement based approach in semiconductor manufacturing from Back End of Line (BEOL) perspective. Our findings open up a new pathway for accessing simultaneous overlay as well as process window and margins from a robust, high throughput and electrical measurement approach.

  7. Dynamics of explosive paroxysms at open andesitic systems: high-resolution mass distribution analyses of 2006 tephra from Tungurahua volcano (Ecuador) (United States)

    Le Pennec, J.; Eychenne, J.; Ramon, P.; Yepes, H.


    Many andesitic volcanoes at subduction plate margins can experience in the course of their evolution periods of sub-continuous eruption during years, decades, or centuries. Such long-lived periods may embrace more or less intense outgassing events, extrusion of viscous lava flows and domes (e.g. Colima in Mexico, Merapi in Indonesia, Arenal in Costa Rica), and explosive activity of uneven intensity (e.g. Semeru in Indonesia, Sakurajima in Japan, Sangay in Ecuador). In addition, strong explosive events of short duration may occur, with potential generation of pyroclastic flows on the flanks and beyond, which can pose significant hazards in populated regions. The origin and dynamics of such violent eruptions remain poorly known and may involve a combination of different factors. Tungurahua volcano, Ecuador, reawaken in 1999 and is an example of such open-system behaviour that experienced a strong and deadly andesitic pyroclastic flow-forming event in August 2006. Inspection of the deposits suggested that the event could have been triggered by magma mixing (silicic pumices in the tephra), magma-water interaction (presence of xenolithic clasts) or deep andesitic magma reinjection (based on mineral chemistry). Here we investigate these options by performing a high-resolution mass budget analysis of the scoria fall deposit. This is achieved by analysing componentry compositions and their mass distribution pattern in the layer, which allow us to document and integrate exponential and power laws mass decay rates over wide areas. The results yield a total mass for the tephra layer of ~2 x 1010kg. The pumice mass fraction is far too small (< 0.4 %) to account for the high explosivity of the 2006 event. Similarly, the xenoclastic mass fraction is small (0.2%) and suggests limited magma-water interaction. Instead, we interpret these xenoclasts as a result of upper conduit erosion at a rate of ~30 cm/hour during the paroxysm. Altogether our results support an explosive event

  8. Radial anisotropy ambient noise tomography of volcanoes (United States)

    Mordret, Aurélien; Rivet, Diane; Shapiro, Nikolai; Jaxybulatov, Kairly; Landès, Matthieu; Koulakov, Ivan; Sens-Schönfelder, Christoph


    The use of ambient seismic noise allows us to perform surface-wave tomography of targets which could hardly be imaged by other means. The frequencies involved (~ 0.5 - 20 s), somewhere in between active seismic and regular teleseismic frequency band, make possible the high resolution imaging of intermediate-size targets like volcanic edifices. Moreover, the joint inversion of Rayleigh and Love waves dispersion curves extracted from noise correlations allows us to invert for crustal radial anisotropy. We present here the two first studies of radial anisotropy on volcanoes by showing results from Lake Toba Caldera, a super-volcano in Indonesia, and from Piton de la Fournaise volcano, a hot-spot effusive volcano on the Réunion Island (Indian Ocean). We will see how radial anisotropy can be used to infer the main fabric within a magmatic system and, consequently, its dominant type of intrusion.

  9. A field guide to Newberry Volcano, Oregon (United States)

    Jenson, Robert A.; Donnelly-Nolan, Julie M.; McKay, Daniele


    Newberry Volcano is located in central Oregon at the intersection of the Cascade Range and the High Lava Plains. Its lavas range in age from ca. 0.5 Ma to late Holocene. Erupted products range in composition from basalt through rhyolite and cover ~3000 km2. The most recent caldera-forming eruption occurred ~80,000 years ago. This trip will highlight a revised understanding of the volcano's history based on new detailed geologic work. Stops will also focus on evidence for ice and flooding on the volcano, as well as new studies of Holocene mafic eruptions. Newberry is one of the most accessible U.S. volcanoes, and this trip will visit a range of lava types and compositions including tholeiitic and calc-alkaline basalt flows, cinder cones, and rhyolitic domes and tuffs. Stops will include early distal basalts as well as the youngest intracaldera obsidian flow.

  10. Joint analysis of electric and gravimetric data for volcano monitoring. Application to data acquired at Vulcano Island (southern Italy) from 1993 to 1996 (United States)

    Di Maio, Rosa; Berrino, Giovanna


    Understanding the dynamics of volcanic-hydrothermal systems is a key factor for discriminating between magmatic and hydrothermal nature of the sources responsible for the unrest phenomena observed in active volcanic areas. Numerous studies of geophysical data monitoring in volcano-geothermal districts has indeed proven that close relationships exist between the volcanic and hydrothermal fluid circulation and the anomalous geophysical signals observed at the ground surface. In this paper, a simultaneous analysis that integrates resistivity and gravity data is suggested as a useful tool to infer a consistent conceptual model of hydrothermal volcanic systems and their evolution. An application of the proposed analysis to repeated resistivity and gravity measurements performed on Vulcano Island (Aeolian Archipelago, Sicily, southern Italy) is presented with the aim of gaining information on the dynamics of the volcanic-hydrothermal system. The examined period ranges from December 1993 to September 1996, when significant changes in chemical properties, temperatures and emission rates of La Fossa crater fumaroles were observed, all indicating an increase in the flux of hot deep magmatic gases. The results of our analysis, which refers to a profile located at the foot of the northwest flank of La Fossa cone, suggest that underground cyclic water-to-vapour transformations govern the shallow hydrothermal system dynamics, generally described by a negative correlation between the monitored resistivity and gravity data. The occurrence of positive correlations between the two analysed parameters could be ascribed to volcanic dynamics, which would mask the normal hydrological and hydrothermal system behaviour.

  11. Impedance spectroscopy analysis on electrical properties of serpentine at high pressure and high temperature

    Institute of Scientific and Technical Information of China (English)

    朱茂旭; 谢鸿森; 郭捷; 许祖鸣; 白武明


    The electrical conductivity of serpentine is measured and the microscopic conductance mechanisms are investigated with impedance spectroscopy at 2.5-4.0 GPa and 220-780℃. The results show that the electrical conductivity is strongly dependent on the frequencies used, and that only arcⅠ, which reflects grain interior conductance, occurs and dominates the whole conductance processes over 12-105 Hz at high pressure before dehydration. The arcⅡ, which indicates the grain boundary process, begins to occur at the initial stage of dehydration. After dehydration, due to the presence of highly conductive networks of free water, the electrical conductivity is not depen-dent on frequencies any longer and the total electrical conductivity is dominated by process of ionic conductance of free water in interconnected networks. Dehydration of serpentine enhances pro-nouncedly the total electrical conductivity, through which highly conductive layers (HCL) may be formed in the earth's interior.

  12. Experimental constraints on the P/T conditions of high silica andesite storage preceding the 2006 eruption of Augustine Volcano, Alaska (United States)

    Henton, S.; Larsen, J. F.; Traxler, N.


    We present new experimental results to constrain the P/T storage conditions of the high silica andesite (HSA) prior to the 2006 eruption of Augustine Volcano, Alaska. Augustine Volcano forms a small island located in Alaska’s Cook Inlet, approximately 180 miles southwest of Anchorage. The 2006 eruption began January 11, 2006, and evolved from an initial phase of explosive activity, through continuous and effusive phases, ending approximately mid-March 2006. Lithologies erupted indicate pervasive hybridization between high- (HSA; 62.2-63.3 wt. % SiO2) and low-silica andesite (LSA; 56.6-58.7 wt% SiO2). This study focuses on experiments using the HSA as starting material to constrain magma storage conditions, based on amphibole stability. Experiments were conducted between 100-160 MPa and 800-900 °C, utilzing H2O saturated conditions and fO2 of Re-ReO. Both lightly crushed and sintered HSA were used as starting powders, seeded respectively with 5 wt. % amphibole and a mix of 5 wt. % amphibole and 20 wt. % plagioclase. Experiments with sintered starting material tended toward a bimodal distribution of experimental phenocrysts and microlites, whilst experiments of the lightly crushed material are more phenocryst rich. Preliminary results indicate that amphibole is stable at conditions of 120-140 MPa and 820-840 °C. These pressures correspond with depths of approximately 4.6-5.4 km, which are consistent with prior magma storage models for Augustine 1986 and 2006 magmas, as well as amphiboles found in other arc andesites (e.g., Redoubt and Soufriere Hills volcanoes). Experimental amphiboles are magnesio-hornblendes, which is in keeping with the natural HSA amphiboles. Experimental and natural hornblendes are similar in composition, with the main difference being a small FeO enrichment (2-3 wt%) and MgO depletion (1-2wt%) in the experimental grains. Further work will provide a more complete assessment of amphibole stability and composition, and will be applied towards

  13. High-speed Integrated Circuits for electrical/Optical Interfaces

    DEFF Research Database (Denmark)

    Jespersen, Christoffer Felix


    This thesis is a continuation of the effort to increase the bandwidth of communicationnetworks. The thesis presents the results of the design of several high-speed electrical ircuits for an electrical/optical interface. These circuits have been a contribution to the ESTA project in collaboration ...... as examples. Finally, it is concluded that the VIP-2 process is suitable technology for creating circuits for 100 Gb/s communication networks. Keywords: Indium Phosphide (InP), DHBT, VCO, Colpitt, Static Divider, CDR, PLL, Transceiver...... represents the avant-garde of InP technology, with ft and fmax well above 300 GHz. Principles of high speed design are presented and described as a useful background before proceeding to circuits. A static divider is used as an example to illustrate many of the design principles. Theory and fundamentals...

  14. Study on High Efficient Electric Vehicle Wireless Charging System (United States)

    Chen, H. X.; Liu, Z. Z.; Zeng, H.; Qu, X. D.; Hou, Y. J.


    Electric and unmanned is a new trend in the development of automobile, cable charging pile can not meet the demand of unmanned electric vehicle. Wireless charging system for electric vehicle has a high level of automation, which can be realized by unmanned operation, and the wireless charging technology has been paid more and more attention. This paper first analyses the differences in S-S (series-series) and S-P (series-parallel) type resonant wireless power supply system, combined with the load characteristics of electric vehicle, S-S type resonant structure was used in this system. This paper analyses the coupling coefficient of several common coil structure changes with the moving distance of Maxwell Ansys software, the performance of disc type coil structure is better. Then the simulation model is established by Simulink toolbox in Matlab, to analyse the power and efficiency characteristics of the whole system. Finally, the experiment platform is set up to verify the feasibility of the whole system and optimize the system. Based on the theoretical and simulation analysis, the higher charging efficiency is obtained by optimizing the magnetic coupling mechanism.

  15. Muon imaging of volcanoes with Cherenkov telescopes (United States)

    Carbone, Daniele; Catalano, Osvaldo; Cusumano, Giancarlo; Del Santo, Melania; La Parola, Valentina; La Rosa, Giovanni; Maccarone, Maria Concetta; Mineo, Teresa; Pareschi, Giovanni; Sottile, Giuseppe; Zuccarello, Luciano


    The quantitative understanding of the inner structure of a volcano is a key feature to model the processes leading to paroxysmal activity and, hence, to mitigate volcanic hazards. To pursue this aim, different geophysical techniques are utilized, that are sensitive to different properties of the rocks (elastic, electrical, density). In most cases, these techniques do not allow to achieve the spatial resolution needed to characterize the shallowest part of the plumbing system and may require dense measurements in active zones, implying a high level of risk. Volcano imaging through cosmic-ray muons is a promising technique that allows to overcome the above shortcomings. Muons constantly bombard the Earth's surface and can travel through large thicknesses of rock, with an energy loss depending on the amount of crossed matter. By measuring the absorption of muons through a solid body, one can deduce the density distribution inside the target. To date, muon imaging of volcanic structures has been mainly achieved with scintillation detectors. They are sensitive to noise sourced from (i) the accidental coincidence of vertical EM shower particles, (ii) the fake tracks initiated from horizontal high-energy electrons and low-energy muons (not crossing the target) and (iii) the flux of upward going muons. A possible alternative to scintillation detectors is given by Cherenkov telescopes. They exploit the Cherenkov light emitted when charged particles (like muons) travel through a dielectric medium, with velocity higher than the speed of light. Cherenkov detectors are not significantly affected by the above noise sources. Furthermore, contrarily to scintillator-based detectors, Cherenkov telescopes permit a measurement of the energy spectrum of the incident muon flux at the installation site, an issue that is indeed relevant for deducing the density distribution inside the target. In 2014, a prototype Cherenkov telescope was installed at the Astrophysical Observatory of Serra

  16. High Specific Energy Pulsed Electric Discharge Laser Research. (United States)


    drop out excess water, filtered, dried, filtered again, and then pumped up to the storage bottle pressure (Fig. 47). At the exit of the high...pressure pump, an oil filter was used to remove any oil that may have been introduced by the compressor. Bottles were pumped up to 2000 psig...Lowder, R. S. , "Air-Combustion Product N2-C02 Electric Laser, " J. Appl. Phys. Lett. 26, 373 (1975). 5. Miller, D. J. and Millikan , R. C

  17. Pulsed high voltage electric discharge disinfection of microbially contaminated liquids. (United States)

    Anpilov, A M; Barkhudarov, E M; Christofi, N; Kop'ev, V A; Kossyi, I A; Taktakishvili, M I; Zadiraka, Y


    To examine the use of a novel multielectrode slipping surface discharge (SSD) treatment system, capable of pulsed plasma discharge directly in water, in killing micro-organisms. Potable water containing Escherichia coli and somatic coliphages was treated with pulsed electric discharges generated by the SSD. The SSD system was highly efficient in the microbial disinfection of water with a low energy utilization (eta approximately 10-4 kW h l-1). The SSD treatment was effective in the destruction of E. coli and its coliphages through the generation of u.v. radiation, ozone and free radicals. The non-thermal treatment method can be used for the eradication of micro-organisms in a range of contaminated liquids, including milk, negating the use of pasteurization. The method utilizes multipoint electric discharges capable of treating large volumes of liquid under static and flowing regimes.

  18. Volcanoes - Direct Download (United States)

    U.S. Geological Survey, Department of the Interior — This map layer includes Holocene volcanoes, which are those thought to be active in the last 10,000 years, that are within an extended area of the northern...

  19. Italian active volcanoes

    Institute of Scientific and Technical Information of China (English)

    RobertoSantacroce; RenawCristofolini; LuigiLaVolpe; GiovanniOrsi; MauroRosi


    The eruptive histories, styles of activity and general modes of operation of the main active Italian volcanoes,Etna, Vulcano, Stromboli, Vesuvio, Campi Flegrei and Ischia, are described in a short summary.

  20. Electrical Impact of SiC Structural Crystal Defects on High Electric Field Devices (Invited) (United States)

    Neudeck, Philip G.


    As illustrated by the invited paper at this conference and other works, SiC wafers and epilayers contain a variety of crystallographic imperfections, including micropipes, closed-core screw dislocations, grain boundaries, basal plane dislocations, heteropolytypic inclusions, and surfaces that are often damaged and contain atomically rough features like step bunching and growth pits or hillocks. Present understanding of the operational impact of various crystal imperfections on SiC electrical devices is reviewed, with an emphasis placed on high-field SiC power devices and circuits.

  1. Cutting Costs by Locating High Production Wells: A Test of the Volcano seismic Approach to Finding ''Blind'' Resources

    Energy Technology Data Exchange (ETDEWEB)

    Eylon Shalev; Peter E. Malin; Wendy McCausland


    In the summer of 2000, Duke University and the Kenyan power generation company, KenGen, conducted a microearthquake monitoring experiment at Longonot volcano in Kenya. Longonot is one of several major late Quaternary trachyte volcanoes in the Kenya Rift. They study was aimed at developing seismic methods for locating buried hydrothermal areas in the Rift on the basis of their microearthquake activity and wave propagation effects. A comparison of microearthquake records from 4.5 Hz, 2 Hz, and broadband seismometers revealed strong high-frequency site and wave-propagation effects. The lower frequency seismometers were needed to detect and record individual phases. Two-dozen 3-component 2- Hz L22 seismographs and PASSCAL loggers were then distributed around Longonot. Recordings from this network located one seismically active area on Longonot's southwest flank. The events from this area were emergent, shallow (<3 km), small (M<1), and spatially restricted. Evidently, the hydrothermal system in this area is not currently very extensive or active. To establish the nature of the site effects, the data were analyzed using three spectral techniques that reduce source effects. The data were also compared to a simple forward model. The results show that, in certain frequency ranges, the technique of dividing the horizontal motion by the vertical motion (H/V) to remove the source fails because of non-uniform vertical amplification. Outside these frequencies, the three methods resolve the same, dominant, harmonic frequencies at a given site. In a few cases, the spectra can be fit with forward models containing low velocity surface layers. The analysis suggests that the emergent, low frequency character of the microearthquake signals is due to attenuation and scattering in the near surface ash deposits.

  2. Evidences of volcanic unrest on high-temperature fumaroles by satellite thermal monitoring: The case of Santa Ana volcano, El Salvador (United States)

    Laiolo, M.; Coppola, D.; Barahona, F.; Benítez, J. E.; Cigolini, C.; Escobar, D.; Funes, R.; Gutierrez, E.; Henriquez, B.; Hernandez, A.; Montalvo, F.; Olmos, R.; Ripepe, M.; Finizola, A.


    On October 1st, 2005, Santa Ana volcano (El Salvador) underwent a VEI 3 phreatomagmatic eruption after approximately one century of rest. Casualties and damages to some of the local infrastructures and surrounding plantations were followed by the evacuation of the nearby communities. The analysis of MODIS (Moderate Resolution Imaging Spectroradiometer) infrared data reveals that the main explosion was preceded by a one-year-long thermal unrest, associated to the development of a fumaroles field, located at the western rim of the summit crater lake. By combining space-based thermal flux and ground-based measurements (seismicity, sulfur emissions and lake temperatures), we suggest that the activity observed at Santa Ana between 2004 and 2005 was driven by the gradual intrusion of an undegassed magma body at a very shallow depth. Magma injection induced thermal anomalies associated with sustained degassing from the fumaroles field and promoted the interaction between the magmatic-hydrothermal system and the overlying water table. This process culminated into the VEI 3 phreatomagmatic eruption of October 2005 that strongly modified the shallow structure of the crater area. The subsequent three-years-long activity resulted from self-sealing of the fracture system and by the opening of a new fracture network directly connecting the deeper hydrothermal system with the crater lake. Our results show that satellite-based thermal data allow us to detect the expansion of the high-temperature fumarolic field. This may precede an explosive eruption and/or a lava dome extrusion. In particular, we show that thermal records can be analyzed with other geochemical (i.e. SO2 emissions) and geophysical (seismicity) data to track a shallow magmatic intrusion interacting with the surrounding hydrothermal system. This provides a remarkable support for volcano monitoring and eruption forecasting, particularly in remote areas where permanent ground data acquisition is hazardous, expensive

  3. Electrical Impact of SiC Structural Crystal Defects on High Electric Field Devices (United States)

    Neudeck, Philip G.


    Commercial epilayers are known to contain a variety of crystallographic imperfections. including micropipes, closed core screw dislocations. low-angle boundaries, basal plane dislocations, heteropolytypic inclusions, and non-ideal surface features like step bunching and pits. This paper reviews the limited present understanding of the operational impact of various crystal defects on SiC electrical devices. Aside from micropipes and triangular inclusions whose densities have been shrinking towards manageably small values in recent years, many of these defects appear to have little adverse operational and/or yield impact on SiC-based sensors, high-frequency RF, and signal conditioning electronics. However high-power switching devices used in power management and distribution circuits have historically (in silicon experience) demanded the highest material quality for prolonged safe operation, and are thus more susceptible to operational reliability problems that arise from electrical property nonuniformities likely to occur at extended crystal defects. A particular emphasis is placed on the impact of closed-core screw dislocations on high-power switching devices, because these difficult to observe defects are present in densities of thousands per cm,in commercial SiC epilayers. and their reduction to acceptable levels seems the most problematic at the present time.

  4. Volcano Monitoring Using Google Earth (United States)

    Bailey, J. E.; Dehn, J.; Webley, P.; Skoog, R.


    At the Alaska Volcano Observatory (AVO), Google Earth is being used as a visualization tool for operational satellite monitoring of the region's volcanoes. Through the abilities of the Keyhole Markup Language (KML) utilized by Google Earth, different datasets have been integrated into this virtual globe browser. Examples include the ability to browse thermal satellite image overlays with dynamic control, to look for signs of volcanic activity. Webcams can also be viewed interactively through the Google Earth interface to confirm current activity. Other applications include monitoring the location and status of instrumentation; near real-time plotting of earthquake hypocenters; mapping of new volcanic deposits; and animated models of ash plumes within Google Earth, created by a combination of ash dispersion modeling and 3D visualization packages. The globe also provides an ideal interface for displaying near real-time information on detected thermal anomalies or "hotspot"; pixels in satellite images with elevated brightness temperatures relative to the background temperature. The Geophysical Institute at the University of Alaska collects AVHRR (Advanced Very High Resolution Radiometer) and MODIS (Moderate Resolution Imaging Spectroradiometer) through its own receiving station. The automated processing that follows includes application of algorithms that search for hotspots close to volcano location, flagging those that meet certain criteria. Further automated routines generate folders of KML placemarkers, which are linked to Google Earth through the network link function. Downloadable KML files have been created to provide links to various data products for different volcanoes and past eruptions, and to demonstrate examples of the monitoring tools developed. These KML files will be made accessible through a new website that will become publicly available in December 2006.

  5. Improving NASICON Sinterability through Crystallization under High Frequency Electrical Fields

    Directory of Open Access Journals (Sweden)

    Ilya eLisenker


    Full Text Available The effect of high frequency (HF electric fields on the crystallization and sintering rates of a lithium aluminum germanium phosphate (LAGP ion conducting ceramic was investigated. LAGP with the nominal composition Li1.5Al0.5Ge1.5(PO43 was crystallized and sintered, both conventionally and under effect of electrical field. Electrical field application, of 300V/cm at 1MHz, produced up to a 40% improvement in sintering rate of LAGP that was crystallized and sintered under the HF field. Heat sink effect of the electrodes appears to arrest thermal runaway and subsequent flash behavior. Sintered pellets were characterized using XRD, SEM, TEM and EIS to compare conventionally and field sintered processes. The as-sintered structure appears largely unaffected by the field as the sintering curves tend to converge beyond initial stages of sintering. Differences in densities and microstructure after 1 hour of sintering were minor with measured sintering strains of 31% vs. 26% with and without field, respectively . Ionic conductivity of the sintered pellets was evaluated and no deterioration due to the use of HF field was noted, though capacitance of grain boundaries due to secondary phases was significantly increased.

  6. Analysis of highly-efficient electric residential HPWHs

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, Van D [ORNL; Murphy, Richard W [ORNL; Rice, C Keith [ORNL; Shen, Bo [ORNL; Gao, Zhiming [ORNL


    A scoping level analysis was conducted to identify electric HPWH concepts that have the potential to achieve or exceed 30% source energy savings compared to a gas tankless water heater (GTWH) representative of the type represented in version beta of the BEopt software developed by the National Renewable Energy Laboratory. The analysis was limited to evaluation of options to improve the energy efficiency of electric HPWH product designs currently on the market in the US. The report first defines the baseline GTWH system and determines its efficiency (source-energy-based adjusted or derated EF of ~0.71). High efficiency components (compressors, pumps, fans, heat exchangers, etc.) were identified and applied to current US HPWH products and analyzed to determine the viability of reaching the target EF. The target site-based energy factor (EF) required for an electric HPWH necessary to provide 30% source energy savings compared to the GTWH baseline unit is then determined to be ~3.19.

  7. Nucleon Electric Dipole Moments in High-Scale Supersymmetric Models

    CERN Document Server

    Hisano, Junji; Kuramoto, Wataru; Kuwahara, Takumi


    The electric dipole moments (EDMs) of electron and nucleons are the promising probe of the new physics. In the generic high-scale supersymmetric (SUSY) scenarios such as models based on mixture of the anomaly and gauge mediations, gluino has an additional contribution to the nucleon EDMs. In this paper, we estimated the effect of the CP-violating gluon Weinberg operator induced by the gluino chromoelectric dipole moment in the high-scale SUSY scenarios, and we evaluated the nucleon and electron EDMs in these scenarios. We found that in the generic high-scale SUSY models, the nucleon EDMs may receive the sizable contribution from the Weinberg operator. Thus, it is important to compare the nucleon EDMs with the electron EDM in order to discriminate among the high-scale SUSY models.

  8. Nucleon electric dipole moments in high-scale supersymmetric models (United States)

    Hisano, Junji; Kobayashi, Daiki; Kuramoto, Wataru; Kuwahara, Takumi


    The electric dipole moments (EDMs) of electron and nucleons are promising probes of the new physics. In generic high-scale supersymmetric (SUSY) scenarios such as models based on mixture of the anomaly and gauge mediations, gluino has an additional contribution to the nucleon EDMs. In this paper, we studied the effect of the CP -violating gluon Weinberg operator induced by the gluino chromoelectric dipole moment in the high-scale SUSY scenarios, and we evaluated the nucleon and electron EDMs in the scenarios. We found that in the generic high-scale SUSY models, the nucleon EDMs may receive the sizable contribution from the Weinberg operator. Thus, it is important to compare the nucleon EDMs with the electron one in order to discriminate among the high-scale SUSY models.

  9. Lightweight High Efficiency Electric Motors for Space Applications (United States)

    Robertson, Glen A.; Tyler, Tony R.; Piper, P. J.


    Lightweight high efficiency electric motors are needed across a wide range of space applications from - thrust vector actuator control for launch and flight applications to - general vehicle, base camp habitat and experiment control for various mechanisms to - robotics for various stationary and mobile space exploration missions. QM Power?s Parallel Path Magnetic Technology Motors have slowly proven themselves to be a leading motor technology in this area; winning a NASA Phase II for "Lightweight High Efficiency Electric Motors and Actuators for Low Temperature Mobility and Robotics Applications" a US Army Phase II SBIR for "Improved Robot Actuator Motors for Medical Applications", an NSF Phase II SBIR for "Novel Low-Cost Electric Motors for Variable Speed Applications" and a DOE SBIR Phase I for "High Efficiency Commercial Refrigeration Motors" Parallel Path Magnetic Technology obtains the benefits of using permanent magnets while minimizing the historical trade-offs/limitations found in conventional permanent magnet designs. The resulting devices are smaller, lower weight, lower cost and have higher efficiency than competitive permanent magnet and non-permanent magnet designs. QM Power?s motors have been extensively tested and successfully validated by multiple commercial and aerospace customers and partners as Boeing Research and Technology. Prototypes have been made between 0.1 and 10 HP. They are also in the process of scaling motors to over 100kW with their development partners. In this paper, Parallel Path Magnetic Technology Motors will be discussed; specifically addressing their higher efficiency, higher power density, lighter weight, smaller physical size, higher low end torque, wider power zone, cooler temperatures, and greater reliability with lower cost and significant environment benefit for the same peak output power compared to typically motors. A further discussion on the inherent redundancy of these motors for space applications will be provided.

  10. Review of the Dynamics of Coalescence and Demulsification by High-Voltage Pulsed Electric Fields


    Ye Peng; Tao Liu; Haifeng Gong; Xianming Zhang


    The coalescence of droplets in oil can be implemented rapidly by high-voltage pulse electric field, which is an effective demulsification dehydration technological method. At present, it is widely believed that the main reason of pulse electric field promoting droplets coalescence is the dipole coalescence and oscillation coalescence in pulse electric field, and the optimal coalescence pulse electric field parameters exist. Around the above content, the dynamics of high-voltage pulse electric...

  11. High thermal power density heat transfer apparatus providing electrical isolation at high temperature using heat pipes (United States)

    Morris, J. F. (Inventor)


    This invention is directed to transferring heat from an extremely high temperature source to an electrically isolated lower temperature receiver. The invention is particularly concerned with supplying thermal power to a thermionic converter from a nuclear reactor with electric isolation. Heat from a high temperature heat pipe is transferred through a vacuum or a gap filled with electrically nonconducting gas to a cooler heat pipe. If the receiver requires gratr thermal power density, geometries are used with larger heat pipe areas for transmitting and receiving energy than the area for conducting the heat to the thermionic converter. In this way the heat pipe capability for increasing thermal power densities compensates for the comparative low thermal power densities through the electrically nonconducting gap between the two heat pipes.

  12. Spreading and collapse of big basaltic volcanoes (United States)

    Puglisi, Giuseppe; Bonforte, Alessandro; Guglielmino, Francesco; Peltier, Aline; Poland, Michael


    Supersite volcanoes, due to their similarities and differences, coupled with their long-time and high-level monitoring networks, represent the best natural laboratories for investigating the manifestations and mechanisms of spreading and collapse, the feedback process between spreading and eruptive activity (especially along rift zones), and the role of the regional geodynamics.

  13. The seismicity of Marapi volcano, West Sumatra. (United States)

    D'Auria, L.


    Marapi is one of the active volcanoes in West Sumatra. It is a stratovolcano with an edifice that is elongated in the ENE-WSW direction. Its elevation is about 2,900 m a.s.l. The summit area is characterized by a caldera that contains some active craters aligned along the ENE-WSW direction. The Marapi volcano is an attractive region for tourists and hosts many small communities its surrounding areas. The recent history of Mt. Marapi is characterized by explosive activity at the summit craters. No lava flows have passed the rim of the summit caldera in recent times. The last eruption occurred on August 5, 2004, and consisted of moderate explosive activity from the central crater. In 1975 an eruption with magmatic and phreatic explosive phases and mudflows and lahars occurred that caused fatalities in the surrounding areas. Since 1980 other eruptions have occurred at Marapi volcano. Even if the explosive intensities of those eruptions have been small to moderate, in some cases, there were fatalities. A cooperation project started between Italy and Indonesia (COVIN) for the monitoring of volcanoes in West Sumatra. In the context of this project a monitoring centre has been set up at the Bukittinggi Observatory and a seismological monitoring system for Marapi volcano has been realized. This system is based on a broadband seismic network including 4 three-component stations. The data acquired by the broadband network of Marapi volcano are continuous recordings of the seismic signals starting from 19/10/2006. Volcano-Tectonic and Long Period events of Marapi volcano together with regional and teleseismic earthquakes are recorded. Several events of high magnitude located at short distances from the network were also recorded such as on March 6, 2007, when two events of Magnitudes Mw 6.4 and 6.3 were recorded with the epicentres near the Marapi volcano. During the following days, there was a sequence of hundreds of aftershocks. The preliminary analysis of the seismicity of

  14. Cook Inlet and Kenai Peninsula, Alaska ESI: VOLCANOS (Volcano Points) (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains the locations of volcanos in Cook Inlet and Kenai Peninsula, Alaska. Vector points in the data set represent the location of the volcanos....

  15. A High-power Electric Propulsion Test Platform in Space (United States)

    Petro, Andrew J.; Reed, Brian; Chavers, D. Greg; Sarmiento, Charles; Cenci, Susanna; Lemmons, Neil


    This paper will describe the results of the preliminary phase of a NASA design study for a facility to test high-power electric propulsion systems in space. The results of this design study are intended to provide a firm foundation for subsequent detailed design and development activities leading to the deployment of a valuable space facility. The NASA Exploration Systems Mission Directorate is sponsoring this design project. A team from the NASA Johnson Space Center, Glenn Research Center, the Marshall Space Flight Center and the International Space Station Program Office is conducting the project. The test facility is intended for a broad range of users including government, industry and universities. International participation is encouraged. The objectives for human and robotic exploration of space can be accomplished affordably, safely and effectively with high-power electric propulsion systems. But, as thruster power levels rise to the hundreds of kilowatts and up to megawatts, their testing will pose stringent and expensive demands on existing Earth-based vacuum facilities. These considerations and the human access to near-Earth space provided by the International Space Station (ISS) have led to a renewed interest in space testing. The ISS could provide an excellent platform for a space-based test facility with the continuous vacuum conditions of the natural space environment and no chamber walls to modify the open boundary conditions of the propulsion system exhaust. The test platform could take advantage of the continuous vacuum conditions of the natural space environment. Space testing would provide open boundary conditions without walls, micro-gravity and a realistic thermal environment. Testing on the ISS would allow for direct observation of the test unit, exhaust plume and space-plasma interactions. When necessary, intervention by on-board personnel and post-test inspection would be possible. The ISS can provide electrical power, a location for

  16. High temperature electrical energy storage: advances, challenges, and frontiers. (United States)

    Lin, Xinrong; Salari, Maryam; Arava, Leela Mohana Reddy; Ajayan, Pulickel M; Grinstaff, Mark W


    With the ongoing global effort to reduce greenhouse gas emission and dependence on oil, electrical energy storage (EES) devices such as Li-ion batteries and supercapacitors have become ubiquitous. Today, EES devices are entering the broader energy use arena and playing key roles in energy storage, transfer, and delivery within, for example, electric vehicles, large-scale grid storage, and sensors located in harsh environmental conditions, where performance at temperatures greater than 25 °C are required. The safety and high temperature durability are as critical or more so than other essential characteristics (e.g., capacity, energy and power density) for safe power output and long lifespan. Consequently, significant efforts are underway to design, fabricate, and evaluate EES devices along with characterization of device performance limitations such as thermal runaway and aging. Energy storage under extreme conditions is limited by the material properties of electrolytes, electrodes, and their synergetic interactions, and thus significant opportunities exist for chemical advancements and technological improvements. In this review, we present a comprehensive analysis of different applications associated with high temperature use (40-200 °C), recent advances in the development of reformulated or novel materials (including ionic liquids, solid polymer electrolytes, ceramics, and Si, LiFePO4, and LiMn2O4 electrodes) with high thermal stability, and their demonstrative use in EES devices. Finally, we present a critical overview of the limitations of current high temperature systems and evaluate the future outlook of high temperature batteries with well-controlled safety, high energy/power density, and operation over a wide temperature range.

  17. Volcanoes: Coming Up from Under. (United States)

    Science and Children, 1980


    Provides specific information about the eruption of Mt. St. Helens in March 1980. Also discusses how volcanoes are formed and how they are monitored. Words associated with volcanoes are listed and defined. (CS)

  18. Exploring the limits of life: microbiology and organic geochemistry of the world's highest lake atop the Licancabur volcano (6000m) and adjacent high altitude lakes (United States)

    Fike, D.; Cabrol, N.; Grin, E.; Hock, A.; 2002 Licancabur Expedition Team


    The world’s highest lake lies atop the Licancabur volcano (6017m) on the border of Chile and Bolivia, and, along with several lakes at the base of the volcano, is the site of an ongoing expedition sponsored by NASA Ames Research Center. The environment around these lakes is quite extreme, due to the aridity, the high UV flux, and low oxygen concentrations. As such, the site has significant astrobiological relevance, both for understanding the limits of life on Earth, and as an analogy to life on early Earth and, more speculatively, on Mars. The field area is located at 23.8S latitude and 67.8W longitude, and is part of the Altiplano in the High Andes, an extension of the Atacama Desert, the driest desert on Earth. During the 2002 Licancabur Expedition (16 Oct 8 Nov 2002), the intensity of UV radiation (wavelengths 250 400 nm) was measured at local noon to be approximately 250 umol/cm2/s at 4300m. Oxygen partial pressures were measured to range between 0.12 atm (at 4300m) and 0.08 atm (at 6000m). A total of four lakes, ranging in altitude from 4300m to 6000m, were examined: Laguna Blanca, Laguna Verde, a hydrothermal pond thereafter named ‘Thermales’, and the Licancabur summit lake. Here, we present a microbiological and organic geochemical characterization of these lakes and their immediate environs. At each lake, samples were collected from the water column, the sediment, and any microbial mats present. DNA was extracted from these samples, amplified with the polymerase chain reaction (PCR), and then the microbial diversity at each lake was assessed by terminal restricted fragment length polymorphism (t-RFLP). Lipids were extracted from the samples using a modified Bligh and Dyer procedure. Analysis by gas chromotography and mass spectroscopy (GC/MS) was used to characterize the presence and concentrations of lipid biomarkers. At the different lakes, changes in microbial community structure can be correlated to changes in environmental parameters, such as

  19. Characterizing Volcanic Processes using Near-bottom, High Resolution Magnetic Mapping of the Caldera and Inner Crater of the Kick'em Jenny Submarine Volcano (United States)

    Ruchala, T. L.; Chen, M.; Tominaga, M.; Carey, S.


    Kick'em Jenny (KEJ) is an active submarine volcano located in the Lesser Antilles subduction zone, 7.5 km north of the Caribbean island Grenada. KEJ, known as one of the most explosive volcanoes in Caribbean, erupted 12 times since 1939 with recent eruptions in 2001 and possibly in 2015. Multiple generations of submarine landslides and canyons have been observed in which some of them can be attributed to past eruptions. The structure of KEJ can be characterized as a 1300 m high conical profile with its summit crater located around 180 m in depth. Active hydrothermal venting and dominantly CO2 composition gas seepage take place inside this 250m diameter crater, with the most activity occurring primarily within a small ( 70 x 110 m) depression zone (inner crater). In order to characterize the subsurface structure and decipher the processes of this volcanic system, the Nautilus NA054 expedition in 2014 deployed the underwater Remotely Operated Vehicle (ROV) Hercules to conduct near-bottom geological observations and magnetometry surveys transecting KEJ's caldera. Raw magnetic data was corrected for vehicle induced magnetic noise, then merged with ROV to ship navigation at 1 HZ. To extract crustal magnetic signatures, the reduced magnetic data was further corrected for external variations such as the International Geomagnetic Reference Field and diurnal variations using data from the nearby San Juan Observatory. We produced a preliminary magnetic anomaly map of KEJ's caldera for subsequent inversion and forward modeling to delineate in situ magnetic source distribution in understanding volcanic processes. We integrated the magnetic characterization of the KEJ craters with shipboard multibeam, ROV visual descriptions, and photomosaics. Initial observations show the distribution of short wavelength scale highly magnetized source centered at the north western part of the inner crater. Although locations of gas seeps are ubiquitous over the inner crater area along ROV

  20. Geology, tectonics, and the 2002-2003 eruption of the Semeru volcano, Indonesia: Interpreted from high-spatial resolution satellite imagery (United States)

    Solikhin, Akhmad; Thouret, Jean-Claude; Gupta, Avijit; Harris, Andy J. L.; Liew, Soo Chin


    The paper illustrates the application of high-spatial resolution satellite images in interpreting volcanic structures and eruption impacts in the Tengger-Semeru massif in east Java, Indonesia. We use high-spatial resolution images (IKONOS and SPOT 5) and aerial photos in order to analyze the structures of Semeru volcano and map the deposits. Geological and tectonic mapping is based on two DEMs and on the interpretation of aerial photos and four SPOT and IKONOS optical satellite images acquired between 1996 and 2002. We also compared two thermal Surface Kinetic Temperature ASTER images before and after the 2002-2003 eruption in order to delineate and evaluate the impacts of the pyroclastic density currents. Semeru's principal structural features are probably due to the tectonic setting of the volcano. A structural map of the Tengger-Semeru massif shows four groups of faults orientated N40, N160, N75, and N105 to N140. Conspicuous structures, such as the SE-trending horseshoe-shaped scar on Semeru's summit cone, coincide with the N160-trending faults. The direction of minor scars on the east flank parallels the first and second groups of faults. The Semeru composite cone hosts the currently active Jonggring-Seloko vent. This is located on, and buttressed against, the Mahameru edifice at the head of a large scar that may reflect a failure plane at shallow depth. Dipping 35° towards the SE, this failure plane may correspond to a weak basal layer of weathered volcaniclastic rocks of Tertiary age. We suggest that the deformation pattern of Semeru and its large scar may be induced by flank spreading over the weak basal layer of the volcano. It is therefore necessary to consider the potential for flank and summit collapse in the future. The last major eruption took place in December 2002-January 2003, and involved emplacement of block-and-ash flows. We have used the 2003 ASTER Surface Kinetic Temperature image to map the 2002-2003 pyroclastic density current deposits. We

  1. Seismic-induced accelerations detected by two parallel gravity meters in continuous recording with a high sampling rate at Etna volcano

    Directory of Open Access Journals (Sweden)

    P. Stefanelli


    Full Text Available We analyse a microgravity data set acquired from two spring LaCoste & Romberg gravity meters operated in parallel at the same site on Etna volcano (Italy for about two months (August – September 2005. The high sampling rate acquisition (2Hz allowed the correlation of short-lasting gravity fluctuations with seismic events. After characterizing the oscillation behavior of the meters, through the study of spectral content and the background noise level of both sequences, we recognized fluctuations in the gravity data, spanning a range of periods from 1 second to about 30 seconds dominated by components with a period of about 15 ÷ 25 seconds, during time intervals encompassing both local seismic events and large worldwide earthquakes. The data analyses demonstrate that observed earthquake-induced gravity fluctuations have some differences due to diverse spectral content of the earthquakes. When local seismic events which present high frequency content excite the meters, the correlation between the two gravity signals is poor (factor < 0.3. Vice versa, when large worldwide earthquakes occur and low frequency seismic waves dominate the ensuing seismic wavefield, the resonance frequencies of the meters are excited and they react according to more common features. In the latter case, the signals from the two instruments are strongly correlated to each other (up to 0.9. In this paper the behaviors of spring gravimeters in the frequency range of the disturbances produced by local and large worldwide earthquakes are presented and discussed.

  2. Diversity of extremophilic bacteria in the sediment of high-altitude lakes located in the mountain desert of Ojos del Salado volcano, Dry-Andes. (United States)

    Aszalós, Júlia Margit; Krett, Gergely; Anda, Dóra; Márialigeti, Károly; Nagy, Balázs; Borsodi, Andrea K


    Ojos del Salado, the highest volcano on Earth is surrounded by a special mountain desert with extreme aridity, great daily temperature range, intense solar radiation, and permafrost from 5000 meters above sea level. Several saline lakes and permafrost derived high-altitude lakes can be found in this area, often surrounded by fumaroles and hot springs. The aim of this study was to gain information about the bacterial communities inhabiting the sediment of high-altitude lakes of the Ojos del Salado region located between 3770 and 6500 m. Altogether 11 sediment samples from 4 different altitudes were examined with 16S rRNA gene based denaturing gradient gel electrophoresis and clone libraries. Members of 17 phyla or candidate divisions were detected with the dominance of Proteobacteria, Acidobacteria, Actinobacteria and Bacteroidetes. The bacterial community composition was determined mainly by the altitude of the sampling sites; nevertheless, the extreme aridity and the active volcanism had a strong influence on it. Most of the sequences showed the highest relation to bacterial species or uncultured clones from similar extreme environments.

  3. Organizational changes at Earthquakes & Volcanoes (United States)

    Gordon, David W.


    Primary responsibility for the preparation of Earthquakes & Volcanoes within the Geological Survey has shifted from the Office of Scientific Publications to the Office of Earthquakes, Volcanoes, and Engineering (OEVE). As a consequence of this reorganization, Henry Spall has stepepd down as Science Editor for Earthquakes & Volcanoes(E&V).

  4. Design of an Ultimate High Speed Electrical Drive System

    Directory of Open Access Journals (Sweden)

    C. Vishnu Kiran


    Full Text Available New emerging applications in the areas of portable power generation, small turbocompressors and spindles require the development of ultrahigh-speed, low power electrical drives. A 500 000 r/min, 100 W electrical drive system is presented. Because of the ultrahigh-speed requirements, standard machine design and power electronic topology choices no longer apply and the complete drive system has to be considered. A permanent magnet machine with a slotless litz-wire winding is used, which results in a low motor inductance and a high fundamental machine frequency. Three different combinations of power electronic topologies and commutation strategies have been experimentally investigated. A voltage source inverter with block commutation and an additional dc–dc converter is selected as the most optimal choice for the power electronics interface as it results in the lowest volume of the entire drive system due to lower switching losses, no heat sink cooling required, a small number of semiconductor devices, and relatively simple control implementation in a low cost digitalsignal processor.

  5. High precision measurement of electrical resistance across endothelial cell monolayers. (United States)

    Tschugguel, W; Zhegu, Z; Gajdzik, L; Maier, M; Binder, B R; Graf, J


    Effects of vasoactive agonists on endothelial permeability was assessed by measurement of transendothelial electrical resistance (TEER) of human umbilical vein endothelial cells (HUVECs) grown on porous polycarbonate supports. Because of the low values of TEER obtained in this preparation (< 5 omega cm2) a design of an Ussing type recording chamber was chosen that provided for a homogeneous electric field across the monolayer and for proper correction of series resistances. Precision current pulses and appropriate rates of sampling and averaging of the voltage signal allowed for measurement of < 0.1 omega resistance changes of the endothelium on top of a 21 omega series resistance of the support and bathing fluid layers. Histamine (10 microM) and thrombin (10 U/ml) induced an abrupt and substantial decrease of TEER, bradykinin (1 microM) was less effective, PAF (380 nM) and LTC4 (1 microM) had no effect. TEER was also reduced by the calcium ionophore A-23187 (10 microM). The technique allows for measurements of TEER in low resistance monolayer cultures with high precision and time resolution. The results obtained extend previous observations in providing quantitative data on the increase of permeability of HUVECs in response to vasoactive agonists.

  6. Water Impacts of High Solar PV Electricity Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Macknick, Jordan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cohen, Stuart [National Renewable Energy Lab. (NREL), Golden, CO (United States)


    This analysis provides a detailed national and regional description of the water-related impacts and constraints of high solar electricity penetration scenarios in the U.S. in 2030 and 2050. A modified version of the Regional Energy Deployment System (ReEDS) model that incorporates water resource availability and costs as a constraint in each of its 134 Balancing Area (BA) regions was utilized to explore national and regional differences in water use impacts and solar deployment locations under different solar energy cost and water availability scenarios (Macknick et al. 2015). Water resource availability and cost data are from recently completed research at Sandia National Laboratories (Tidwell et al. 2013a). Scenarios analyzed include two business-as-usual solar energy cost cases, one with and one without considering available water resources, and four solar energy cost cases that meet the SunShot cost goals (i.e., $1/watt for utility-scale PV systems), with varying levels of water availability restrictions. This analysis provides insight into the role solar energy technologies have in the broader electricity sector under scenarios of water constraints.

  7. Electrical and hydrodynamic characterization of a high current pulsed arc (United States)

    Sousa Martins, R.; Chemartin, L.; Zaepffel, C.; Lalande, Ph; Soufiani, A.


    High current pulsed arcs are of significant industrial interest and, aiming to reduce time and cost, there is progressively more and more need for computation tools that describe and predict the behaviour of these arcs. These simulation codes need inputs and validations by experimental databases, but accurate data is missing for this category of electric discharges. The principal lack of understanding is with respect to the transient phase of the current, which can reach thousands of amperes in a few microseconds. In this paper, we present the work realized on an experimental setup that simulates in the laboratory an arc column subjected to five levels of high pulsed current, ranging from 10 kA to 100 kA, with the last one corresponding to the standard lightning current waveform used in aircraft certification processes. This device was instrumented by high speed video cameras to assess the characteristic sizes of the arc channel and to characterize the shock wave generated by the arc expansion. The arc channel radius was measured over time during the axisymmetric phase and reached 3.2 cm. The position and velocity of the shock wave was determined during the first 140 μs. The background-oriented schlieren method was used to study the shock wave and a model for the light deflection inside the shock wave was developed. The mass density profile of the shock wave was estimated and showed good agreement with Rankine-Hugoniot relations at the wave front. Electrical measurements were also used to estimate the time-dependent resistance and conductivity of the arc for times lasting up to 50 μs.

  8. Hawaii's volcanoes revealed (United States)

    Eakins, Barry W.; Robinson, Joel E.; Kanamatsu, Toshiya; Naka, Jiro; Smith, John R.; Takahashi, Eiichi; Clague, David A.


    Hawaiian volcanoes typically evolve in four stages as volcanism waxes and wanes: (1) early alkalic, when volcanism originates on the deep sea floor; (2) shield, when roughly 95 percent of a volcano's volume is emplaced; (3) post-shield alkalic, when small-volume eruptions build scattered cones that thinly cap the shield-stage lavas; and (4) rejuvenated, when lavas of distinct chemistry erupt following a lengthy period of erosion and volcanic quiescence. During the early alkalic and shield stages, two or more elongate rift zones may develop as flanks of the volcano separate. Mantle-derived magma rises through a vertical conduit and is temporarily stored in a shallow summit reservoir from which magma may erupt within the summit region or be injected laterally into the rift zones. The ongoing activity at Kilauea's Pu?u ?O?o cone that began in January 1983 is one such rift-zone eruption. The rift zones commonly extend deep underwater, producing submarine eruptions of bulbous pillow lava. Once a volcano has grown above sea level, subaerial eruptions produce lava flows of jagged, clinkery ?a?a or smooth, ropy pahoehoe. If the flows reach the ocean they are rapidly quenched by seawater and shatter, producing a steep blanket of unstable volcanic sediment that mantles the upper submarine slopes. Above sea level then, the volcanoes develop the classic shield profile of gentle lava-flow slopes, whereas below sea level slopes are substantially steeper. While the volcanoes grow rapidly during the shield stage, they may also collapse catastrophically, generating giant landslides and tsunami, or fail more gradually, forming slumps. Deformation and seismicity along Kilauea's south flank indicate that slumping is occurring there today. Loading of the underlying Pacific Plate by the growing volcanic edifices causes subsidence, forming deep basins at the base of the volcanoes. Once volcanism wanes and lava flows no longer reach the ocean, the volcano continues to submerge, while


    Directory of Open Access Journals (Sweden)

    S. Serikov


    Full Text Available The mathematical model of hybrid electric vehicle NiMH high-voltage battery is obtained. This model allows to explore the interaction of vehicle tractive electric drive and high-voltage battery at the electric motive power motion and in the process of recuperation of braking kinetic energy.

  10. Seismic unrest at Katla Volcano- southern Iceland (United States)

    jeddi, zeinab; Tryggvason, Ari; Gudmundsson, Olafur; Bödvarsson, Reynir; SIL Seismology Group


    Katla volcano is located on the propagating Eastern Volcanic Zone (EVZ) in South Iceland. It is located beneath Mýrdalsjökull ice-cap which covers an area of almost 600 km2, comprising the summit caldera and the eruption vents. 20 eruptions between 930 and 1918 with intervals of 13-95 years are documented at Katla which is one of the most active subglacial volcanoes in Iceland. Eruptions at Katla are mainly explosive due to the subglacial mode of extrusion and produce high eruption columns and catastrophic melt water floods (jökulhlaups). The present long Volcanic repose (almost 96 years) at Katla, the general unrest since 1955, and the 2010 eruption of the neighbouring Eyjafjallajökull volcano has prompted concerns among geoscientists about an imminent eruption. Thus, the volcano has been densely monitored by seismologists and volcanologists. The seismology group of Uppsala University as a partner in the Volcano Anatomy (VA) project in collaboration with the University of Iceland and the Icelandic Meteorological Office (IMO) installed 9 temporary seismic stations on and around the Mýrdalsjökull glacier in 2011. Another 10 permanent seismic stations are operated by IMO around Katla. The project's data collection is now finished and temporary stations were pulled down in August 2013. According to seismicity maps of the whole recording period, thousands of microearthquakes have occurred within the caldera region. At least three different source areas are active in Katla: the caldera region, the western Godaland region and a small cluster at the southern rim of Mýrdalsjökull near the glacial stream of Hafursarjökull. Seismicity in the southern flank has basically started after June 2011. The caldera events are mainly volcano-tectonic, while western and southern events are mostly long period (lp) and can be related to glacial or magmatic movement. One motivation of the VA Katla project is to better understand the physical mechanism of these lp events. Changes

  11. Relaxor behavior and electrical properties of high dielectric constant materials

    Institute of Scientific and Technical Information of China (English)


    Several typical high dielectric constant materials are reviewed to study the electrical properties and relaxation mechanism. It is found that a Lorenz-type law can be used to describe the dielectric permit- tivity of either the normal ferroelectrics with or without diffuse phase transitions (DPT) or the typical ferroelectric relaxors. The ferroelectric DPT can be well described by just one fitting process using the Lorenz-type law, while the relaxor ferroelectric transition needs two independent fitting processes. The Lorenz-type law fails at the low temperature side of the dielectric maximum of a first-order ferroelectric phase transition. Above the transition temperature, the dielectric curves of all the studied materials can be well described by a Lorenz-type law.

  12. Relaxor behavior and electrical properties of high dielectric constant materials

    Institute of Scientific and Technical Information of China (English)

    FAN HuiQing; KE ShanMing


    Several typical high dielectric constant materials are reviewed to study the electrical properties and relaxation mechanism.It is found that a Lorenz-type law can be used to describe the dielectric permitUvity of either the normal ferroelectrics with or without diffuse phase transitions(DPT)or the typical ferroelectric relaxors.The ferroelectric DPT can be well described by just one fitting process using the Lorenz-type law,while the relaxor ferroelectric transition needs two independent fitting processes.The Lorenz-type law fails at the low temperature side of the dielectric maximum of a first-order ferroelectric phase transition.Above the transition temperature,the dielectric curves of all the studied materials can be well described by a Lorenz-type law.

  13. Sessile multidroplets and salt droplets under high tangential electric fields (United States)

    Xie, Guoxin; He, Feng; Liu, Xiang; Si, Lina; Guo, Dan


    Understanding the interaction behaviors between sessile droplets under imposed high voltages is very important in many practical situations, e.g., microfluidic devices and the degradation/aging problems of outdoor high-power applications. In the present work, the droplet coalescence, the discharge activity and the surface thermal distribution response between sessile multidroplets and chloride salt droplets under high tangential electric fields have been investigated with infrared thermography, high-speed photography and pulse current measurement. Obvious polarity effects on the discharge path direction and the temperature change in the droplets in the initial stage after discharge initiation were observed due to the anodic dissolution of metal ions from the electrode. In the case of sessile aligned multidroplets, the discharge path direction could affect the location of initial droplet coalescence. The smaller unmerged droplet would be drained into the merged large droplet as a result from the pressure difference inside the droplets rather than the asymmetric temperature change due to discharge. The discharge inception voltages and the temperature variations for two salt droplets closely correlated with the ionization degree of the salt, as well as the interfacial electrochemical reactions near the electrodes. Mechanisms of these observed phenomena were discussed. PMID:27121926

  14. Update of map the volcanic hazard in the Ceboruco volcano, Nayarit, Mexico (United States)

    Suarez-Plascencia, C.; Camarena-Garcia, M. A.; Nunez-Cornu, F. J.


    The Ceboruco Volcano (21° 7.688 N, 104° 30.773 W) is located in the northwestern part of the Tepic-Zacoalco graben. Its volcanic activity can be divided in four eruptive cycles differentiated by their VEI and chemical variations as well. As a result of andesitic effusive activity, the "paleo-Ceboruco" edifice was constructed during the first cycle. The end of this cycle is defined by a plinian eruption (VEI between 3 and 4) which occurred some 1020 years ago and formed the external caldera. During the second cycle an andesitic dome built up in the interior of the caldera. The dome collapsed and formed the internal caldera. The third cycle is represented by andesitic lava flows which partially cover the northern and south-southwestern part of the edifice. The last cycle is represented by the andesitic lava flows of the nineteenth century located in the southwestern flank of the volcano. Actually, moderate fumarolic activity occurs in the upper part of the volcano showing temperatures ranging between 20° and 120°C. Some volcanic high frequency tremors have also been registered near the edifice. Shows the updating of the volcanic hazard maps published in 1998, where we identify with SPOT satellite imagery and Google Earth, change in the land use on the slope of volcano, the expansion of the agricultural frontier on the east sides of the Ceboruco volcano. The population inhabiting the area is 70,224 people in 2010, concentrated in 107 localities and growing at an annual rate of 0.37%, also the region that has shown an increased in the vulnerability for the development of economic activities, supported by highway, high road, railroad, and the construction of new highway to Puerto Vallarta, which is built in the southeast sector of the volcano and electrical infrastructure that connect the Cajon and Yesca Dams to Guadalajara city. The most important economic activity in the area is agriculture, with crops of sugar cane (Saccharum officinarum), corn, and jamaica

  15. The Cenozoic Volcanoes in Northeast China

    Institute of Scientific and Technical Information of China (English)

    LIU Jiaqi; HAN Jingtai; GUO Zhengfu


    There are more than 600 Cenozoic volcanic cones and craters with abeut 50 000 km2of lava flows in northeast China, which formed many volcanic clusters and shown the features of the continental rift - type volcanoes. Most volcanic activities in this area, especially in the east part of Songliao graben, were usually controlled by rifts and faults with the main direction of NE / NNE in parallel and become younger from the central graben towards its both sides, especially to the east continental margin. It is revealed that the volcanism occurred in northeast China was as strong as that occurred in Japan during the Miocene and the Quaternary. The Quaternary basalt that is usually distributed along river valley is called "valley basalt"while Neogene basalt usually distributed in the top of mounts is called "high position basalt". These volcanoes and volcanic rocks are usually composed of alkaline basalts with ultramafic inclusions, except Changbaishan volcano that is built by trachyte and pantellerite.

  16. Renewed unrest at Mount Spurr Volcano, Alaska (United States)

    Power, John A.


    The Alaska Volcano Observatory (AVO),a cooperative program of the U.S. Geological Survey, the University of Alaska Fairbanks Geophysical Institute, and the Alaska Division of Geological and Geophysical Surveys, has detected unrest at Mount Spurr volcano, located about 125 km west of Anchorage, Alaska, at the northeast end of the Aleutian volcanic arc.This activity consists of increased seismicity melting of the summit ice cap, and substantial rates of C02 and H2S emission.The current unrest is centered beneath the volcano's 3374-m-high summit, whose last known eruption was 5000–6000 years ago. Since then, Crater Peak, 2309 m in elevation and 4 km to the south, has been the active vent. Recent eruptions occurred in 1953 and 1992.

  17. The origin of the Hawaiian Volcano Observatory

    Energy Technology Data Exchange (ETDEWEB)

    Dvorak, John [University of Hawaii' s Institute for Astronomy (United States)


    I first stepped through the doorway of the Hawaiian Volcano Observatory in 1976, and I was impressed by what I saw: A dozen people working out of a stone-and-metal building perched at the edge of a high cliff with a spectacular view of a vast volcanic plain. Their primary purpose was to monitor the island's two active volcanoes, Kilauea and Mauna Loa. I joined them, working for six weeks as a volunteer and then, years later, as a staff scientist. That gave me several chances to ask how the observatory had started.

  18. Lithospheric contributions to high-MgO basanites from the Cumbre Vieja Volcano, La Palma, Canary Islands and evidence for temporal variation in plume influence (United States)

    Prægel, N.-O.; Holm, P. M.


    New geochemical and isotopic data are presented from the oldest part of the Cumbre Vieja volcano, La Palma (Canary Islands), located near the assumed emergence of the Canary mantle plume. The volcanics comprise a suite dominated by basanite flows with subordinate amounts of phono-tephrite, tephri-phonolite and phonolite flows and intrusives. Two compositionally different basanite groups have been identified, both with HIMU (high-μ)-type incompatible trace element characteristics: Primitive high-MgO basanites (10.7-12.1% MgO), found only at the base of a stratigraphic profile near Fuencaliente on the south coast, and intermediate-MgO basanites (6.0-7.3% MgO), exposed in the upper part of the profile and widespread on the east coast of La Palma. The high-MgO basanites are interpreted as near-primary mantle melts (primary composition 14-15% MgO) derived by progressive melting (2.9% to 4.5%) of a common lithospheric mantle source. Model calculations indicate that it is not possible to generate the intermediate-MgO basanites from the high-MgO group by crystal fractionation of observed phenocrysts. Relative to intermediate-MgO basanites, the high-MgO flows have lower concentrations of LIL and HFS elements, except for Ti, which is markedly enriched in the primitive rocks (3.7-4.7% TiO 2 vs 3.4-3.9% TiO 2). Fuencaliente volcanics display limited temporal isotopic variations suggested to be a result of mixing of melts originating from the rising plume and the metazomatized lithospheric mantle. 87Sr / 86Sr and 143Nd / 144Nd ratios range 0.70305-0.70311 and 0.51285-0.51291, respectively, while the corresponding ranges in Pb-isotope ratios are 206Pb / 204Pb = 19.46-19.64, 207Pb / 204Pb = 15.55-15.61, and 208Pb / 204Pb = 39.16-39.53. The overall variation of the Cumbre Vieja isotopic data can be accounted for by mixtures of three mantle components in the proportions 72-79% plume source (LVC = low velocity component), 9-16% depleted mantle (DM) and up to 12% enriched mantle

  19. Significance of High-frequency Electrical Brain Activity. (United States)

    Kobayashi, Katsuhiro; Akiyama, Tomoyuki; Agari, Takashi; Sasaki, Tatsuya; Shibata, Takashi; Hanaoka, Yoshiyuki; Akiyama, Mari; Endoh, Fumika; Oka, Makio; Date, Isao


     Electroencephalogram (EEG) data include broadband electrical brain activity ranging from infra-slow bands (frequency bands (e.g., the approx. 10 Hz alpha rhythm) to high-frequency bands of up to 500 Hz. High-frequency oscillations (HFOs) including ripple and fast ripple oscillations (80-200 Hz and>200 / 250 Hz, respectively) are particularly of note due to their very close relationship to epileptogenicity, with the possibility that they could function as a surrogate biomarker of epileptogenicity. In contrast, physiological high-frequency activity plays an important role in higher brain functions, and the differentiation between pathological / epileptic and physiological HFOs is a critical issue, especially in epilepsy surgery. HFOs were initially recorded with intracranial electrodes in patients with intractable epilepsy as part of a long-term invasive seizure monitoring study. However, fast oscillations (FOs) in the ripple and gamma bands (40-80 Hz) are now noninvasively detected by scalp EEG and magnetoencephalography, and thus the scope of studies on HFOs /FOs is rapidly expanding.

  20. A Probabilistic Approach for Real-Time Volcano Surveillance (United States)

    Cannavo, F.; Cannata, A.; Cassisi, C.; Di Grazia, G.; Maronno, P.; Montalto, P.; Prestifilippo, M.; Privitera, E.; Gambino, S.; Coltelli, M.


    Continuous evaluation of the state of potentially dangerous volcanos plays a key role for civil protection purposes. Presently, real-time surveillance of most volcanoes worldwide is essentially delegated to one or more human experts in volcanology, who interpret data coming from different kind of monitoring networks. Unfavorably, the coupling of highly non-linear and complex volcanic dynamic processes leads to measurable effects that can show a large variety of different behaviors. Moreover, due to intrinsic uncertainties and possible failures in some recorded data, the volcano state needs to be expressed in probabilistic terms, thus making the fast volcano state assessment sometimes impracticable for the personnel on duty at the control rooms. With the aim of aiding the personnel on duty in volcano surveillance, we present a probabilistic graphical model to estimate automatically the ongoing volcano state from all the available different kind of measurements. The model consists of a Bayesian network able to represent a set of variables and their conditional dependencies via a directed acyclic graph. The model variables are both the measurements and the possible states of the volcano through the time. The model output is an estimation of the probability distribution of the feasible volcano states. We tested the model on the Mt. Etna (Italy) case study by considering a long record of multivariate data from 2011 to 2015 and cross-validated it. Results indicate that the proposed model is effective and of great power for decision making purposes.

  1. Santa Maria Volcano, Guatemala (United States)


    The eruption of Santa Maria volcano in 1902 was one of the largest eruptions of the 20th century, forming a large crater on the mountain's southwest flank. Since 1922, a lava-dome complex, Santiaguito, has been forming in the 1902 crater. Growth of the dome has produced pyroclastic flows as recently as the 2001-they can be identified in this image. The city of Quezaltenango (approximately 90,000 people in 1989) sits below the 3772 m summit. The volcano is considered dangerous because of the possibility of a dome collapse such as one that occurred in 1929, which killed about 5000 people. A second hazard results from the flow of volcanic debris into rivers south of Santiaguito, which can lead to catastrophic flooding and mud flows. More information on this volcano can be found at web sites maintained by the Smithsonian Institution, Volcano World, and Michigan Tech University. ISS004-ESC-7999 was taken 17 February 2002 from the International Space Station using a digital camera. The image is provided by the Earth Sciences and Image Analysis Laboratory at Johnson Space Center. Searching and viewing of additional images taken by astronauts and cosmonauts is available at the NASA-JSC Gateway to

  2. Anatomy of a volcano

    NARCIS (Netherlands)

    Wassink, J.


    The Icelandic volcano Eyjafjallajökull caused major disruption in European airspace last year. According to his co-author, Freysteinn Sigmundsson, the reconstruction published in Nature six months later by aerospace engineering researcher, Dr Andy Hooper, opens up a new direction in volcanology. “W

  3. Catalogue of Icelandic Volcanoes (United States)

    Ilyinskaya, Evgenia; Larsen, Gudrun; Gudmundsson, Magnus T.; Vogfjord, Kristin; Pagneux, Emmanuel; Oddsson, Bjorn; Barsotti, Sara; Karlsdottir, Sigrun


    The Catalogue of Icelandic Volcanoes is a newly developed open-access web resource in English intended to serve as an official source of information about active volcanoes in Iceland and their characteristics. The Catalogue forms a part of an integrated volcanic risk assessment project in Iceland GOSVÁ (commenced in 2012), as well as being part of the effort of FUTUREVOLC (2012-2016) on establishing an Icelandic volcano supersite. Volcanic activity in Iceland occurs on volcanic systems that usually comprise a central volcano and fissure swarm. Over 30 systems have been active during the Holocene (the time since the end of the last glaciation - approximately the last 11,500 years). In the last 50 years, over 20 eruptions have occurred in Iceland displaying very varied activity in terms of eruption styles, eruptive environments, eruptive products and the distribution lava and tephra. Although basaltic eruptions are most common, the majority of eruptions are explosive, not the least due to magma-water interaction in ice-covered volcanoes. Extensive research has taken place on Icelandic volcanism, and the results reported in numerous scientific papers and other publications. In 2010, the International Civil Aviation Organisation (ICAO) funded a 3 year project to collate the current state of knowledge and create a comprehensive catalogue readily available to decision makers, stakeholders and the general public. The work on the Catalogue began in 2011, and was then further supported by the Icelandic government and the EU through the FP7 project FUTUREVOLC. The Catalogue of Icelandic Volcanoes is a collaboration of the Icelandic Meteorological Office (the state volcano observatory), the Institute of Earth Sciences at the University of Iceland, and the Civil Protection Department of the National Commissioner of the Iceland Police, with contributions from a large number of specialists in Iceland and elsewhere. The Catalogue is built up of chapters with texts and various

  4. Three-dimensional resistivity structure of Asama Volcano revealed by data-space magnetotelluric inversion using unstructured tetrahedral elements (United States)

    Usui, Yoshiya; Ogawa, Yasuo; Aizawa, Koki; Kanda, Wataru; Hashimoto, Takeshi; Koyama, Takao; Yamaya, Yusuke; Kagiyama, Tsuneomi


    Asama Volcano is an andesitic composite volcano and one of the most active volcanoes in Japan. In order to reveal electrical resistivity structure beneath the volcano accurately, we performed a 3-D inversion of dense magnetotelluric survey data. In order to prevent misinterpretation of the subsurface resistivity due to the steep topography around Asama Volcano, we used an unstructured tetrahedral mesh to represent the topography. Furthermore, we reduced the calculation time by transforming the inverse problem from the model space into the data space. Comparison of the new data-space method to the original model-space method showed that the calculation time required to update the model parameters was reduced as a result of the transformation, whereas the resistivity structure obtained remained unchanged. In the subsurface resistivity structure around Asama Volcano that was estimated from the inversion, resistive bodies were discovered to be located under the old eruption centres. In particular, under the 24 ka collapse caldera to the west of the presently active crater, a spherical resistive body was found to exist in isolation. In addition, there was a widespread conductive layer below the resistive surface layer. By comparison with previous hydrological and geochemical studies, the conductive layer was interpreted as being a high-water-content layer and an overlying layer rich in altered clay minerals. Because the western part of the volcanic conduit was considered to be the resistive area, which is inferred to consist of unfractured rocks with lower permeability than their surroundings, it would appear that the area obstructs the westward flow of the hydrothermal fluid beneath the summit, thereby contributing to higher concentrations of SO42- and Cl- in the spring water at the northern and eastern feet as well as the uneven location of a diffuse CO2 anomaly.

  5. Electric heating provides a high level of home comfort - economically

    Energy Technology Data Exchange (ETDEWEB)

    Haapakoski, M.


    Research and development at IVO in the area of electric heating boasts a tradition going back almost thirty years. Research aimed at further progress is continuing. IVO and power companies launched the `Electrically heated houses of the century` project four years ago. The first results show that electric heating continues to be very competitive with other heating systems. It is an economical way of heating the home and it also increases the comfort of those living there

  6. Hazard maps of Colima volcano, Mexico (United States)

    Suarez-Plascencia, C.; Nunez-Cornu, F. J.; Escudero Ayala, C. R.


    Colima volcano, also known as Volcan de Fuego (19° 30.696 N, 103° 37.026 W), is located on the border between the states of Jalisco and Colima and is the most active volcano in Mexico. Began its current eruptive process in February 1991, in February 10, 1999 the biggest explosion since 1913 occurred at the summit dome. The activity during the 2001-2005 period was the most intense, but did not exceed VEI 3. The activity resulted in the formation of domes and their destruction after explosive events. The explosions originated eruptive columns, reaching attitudes between 4,500 and 9,000 m.a.s.l., further pyroclastic flows reaching distances up to 3.5 km from the crater. During the explosive events ash emissions were generated in all directions reaching distances up to 100 km, slightly affected nearby villages as Tuxpan, Tonila, Zapotlán, Cuauhtemoc, Comala, Zapotitlan de Vadillo and Toliman. During the 2005 this volcano has had an intense effusive-explosive activity, similar to the one that took place during the period of 1890 through 1900. Intense pre-plinian eruption in January 20, 1913, generated little economic losses in the lower parts of the volcano due to low population density and low socio-economic activities at the time. Shows the updating of the volcanic hazard maps published in 2001, where we identify whit SPOT satellite imagery and Google Earth, change in the land use on the slope of volcano, the expansion of the agricultural frontier on the east and southeast sides of the Colima volcano, the population inhabiting the area is approximately 517,000 people, and growing at an annual rate of 4.77%, also the region that has shown an increased in the vulnerability for the development of economic activities, supported by the construction of highways, natural gas pipelines and electrical infrastructure that connect to the Port of Manzanillo to Guadalajara city. The update the hazard maps are: a) Exclusion areas and moderate hazard for explosive events

  7. Research on High-efficient Remanufacturing Technologies and Application of Electric Motor (United States)

    Liu, Ren; Zhao, Yuejin; Yang, Xu; Wang, Gen


    The energy conservation of electric motor system is the key of industrial energy conservation. With the implementation and acceleration of electric motor energy efficiency improvement plan, more and more electric motors are knocked out. High-efficient remanufacturing of electric motor refers to improving the efficiency of electric motor and recycling the resources by replacing the winding, iron core and other components of electric motor on the basis of the low-efficient/outdated electric motors, which conforms to China’s policy of circular economy and resource recovery. The remanufacturing of electric motor not only maximizes the use of resources, but also reduces the energy consumption generated by reprocessing of cast iron, silicon steel sheet and other materials in dismantling of electric motor. However, structures and iron core materials used in design and manufacture of electric motors are different, and the degrees of wear of electric motors are also different under different operating conditions, which further result in diversified design schemes, increased remanufacturing cost and reduced remanufacturing efficiency. This paper analyzes the key process technologies for remanufacturing of electric motors are researched by analyzing the remanufacturing technologies of electric motors, and presents the feasibility to replace the cast-aluminum rotor with cast-copper rotor in high-efficient remanufacturing process of electric motor.

  8. Highly Electrically Conducting Glass-Graphene Nanoplatelets Hybrid Coatings. (United States)

    Garcia, E; Nistal, A; Khalifa, A; Essa, Y; Martín de la Escalera, F; Osendi, M I; Miranzo, P


    Hybrid coatings consisting of a heat resistant Y2O3-Al2O3-SiO2 (YAS) glass containing 2.3 wt % of graphene nanoplatelets (GNPs) were developed by flame spraying homogeneous ceramic powders-GNP granules. Around 40% of the GNPs survived the high spraying temperatures and were distributed along the splat-interfaces, forming a percolated network. These YAS-GNP coatings are potentially interesting in thermal protection systems and electromagnetic interference shields for aerospace applications; therefore silicon carbide (SiC) materials at the forefront of those applications were employed as substrates. Whereas the YAS coatings are nonconductive, the YAS-GNP coatings showed in-plane electrical conductivity (∼10(2) S·m(-1)) for which a low percolation limit (below 3.6 vol %) is inferred. Indentation tests revealed the formation of a highly damaged indentation zone showing multiple shear displacements between adjacent splats probably favored by the graphene sheets location. The indentation radial cracks typically found in brittle glass coatings are not detected in the hybrid coatings that are also more compliant.

  9. Applications of geophysical methods to volcano monitoring (United States)

    Wynn, Jeff; Dzurisin, Daniel; Finn, Carol A.; Kauahikaua, James P.; Lahusen, Richard G.


    The array of geophysical technologies used in volcano hazards studies - some developed originally only for volcano monitoring - ranges from satellite remote sensing including InSAR to leveling and EDM surveys, campaign and telemetered GPS networks, electronic tiltmeters and strainmeters, airborne magnetic and electromagnetic surveys, short-period and broadband seismic monitoring, even microphones tuned for infrasound. They include virtually every method used in resource exploration except large-scale seismic reflection. By “geophysical ” we include both active and passive methods as well as geodetic technologies. Volcano monitoring incorporates telemetry to handle high-bandwith cameras and broadband seismometers. Critical geophysical targets include the flux of magma in shallow reservoir and lava-tube systems, changes in active hydrothermal systems, volcanic edifice stability, and lahars. Since the eruption of Mount St. Helens in Washington State in 1980, and the eruption at Pu’u O’o in Hawai’i beginning in 1983 and still continuing, dramatic advances have occurred in monitoring technology such as “crisis GIS” and lahar modeling, InSAR interferograms, as well as gas emission geochemistry sampling, and hazards mapping and eruption predictions. The on-going eruption of Mount St. Helens has led to new monitoring technologies, including advances in broadband Wi-Fi and satellite telemetry as well as new instrumentation. Assessment of the gap between adequate monitoring and threat at the 169 potentially dangerous Holocene volcanoes shows where populations are dangerously exposed to volcanic catastrophes in the United States and its territories . This paper focuses primarily on Hawai’ian volcanoes and the northern Pacific and Cascades volcanoes. The US Geological Survey, the US National Park System, and the University of Utah cooperate in a program to monitor the huge Yellowstone volcanic system, and a separate observatory monitors the restive Long Valley

  10. Degassing vs. eruptive styles at Mt. Etna volcano (Sicily, Italy): Volatile stocking, gas fluxing, and the shift from low-energy to highly-explosive basaltic eruptions (United States)

    Moretti, Roberto; Métrich, Nicole; Di Renzo, Valeria; Aiuppa, Alessandro; Allard, Patrick; Arienzo, Ilenia


    Basaltic magmas can transport and release large amounts of volatiles into the atmosphere, especially in subduction zones, where slab-derived fluids enrich the mantle wedge. Depending on magma volatile content, basaltic volcanoes thus display a wide spectrum of eruptive styles, from common Strombolian-type activity to Plinian events. Mt. Etna in Sicily, is a typical basaltic volcano where the volatile control on such a variable activity can be investigated. Based on a melt inclusion study in products from Strombolian or lava-fountain activity to Plinian eruptions, here we show that for the same initial volatile content, different eruptive styles reflect variable degassing paths throughout the composite Etnean plumbing system. The combined influence of i) crystallization, ii) deep degassing and iii) CO2 gas fluxing can explain the evolution of H2O, CO2, S and Cl in products from such a spectrum of activity. Deep crystallization produces the CO2-rich gas fluxing the upward magma portions, which will become buoyant and easily mobilized in small gas-rich batches stored within the plumbing system. When reaching gas dominated conditions (i.e., a gas/melt mass ratio of 0.3 and CO2,gas/H2Ogas molar ratio 5 ), these will erupt effusively or mildly explosively, whilst in case of the 122 BC Plinian eruption, open-system degassing conditions took place within the plumbing system, such that continuous CO2-fluxing determined gas accumulation on top of the magmatic system. The emission of such a cap in the early eruptive phase triggered the arrival of deep H2O-rich whose fast decompression and bubble nucleation lead to the highly explosive character, enhanced by abundant microlite crystallization and consequent increase of magma effective viscosity. This could explain why open system basaltic systems like Etna may experience highly explosive or even Plinian episodes during eruptions that start with effusive to mildly explosive phases. The proposed mechanism also determines a

  11. Catalogue of Icelandic volcanoes (United States)

    Ilyinskaya, Evgenia; Larsen, Gudrun; Vogfjörd, Kristin; Tumi Gudmundsson, Magnus; Jonsson, Trausti; Oddsson, Björn; Reynisson, Vidir; Barsotti, Sara; Karlsdottir, Sigrun


    Volcanic activity in Iceland occurs on volcanic systems that usually comprise a central volcano and fissure swarm. Over 30 systems have been active during the Holocene. In the last 100 years, over 30 eruptions have occurred displaying very varied activity in terms of eruption styles, eruptive environments, eruptive products and their distribution. Although basaltic eruptions are most common, the majority of eruptions are explosive, not the least due to magma-water interaction in ice-covered volcanoes. Extensive research has taken place on Icelandic volcanism, and the results reported in scientific papers and other publications. In 2010, the International Civil Aviation Organisation funded a 3 year project to collate the current state of knowledge and create a comprehensive catalogue readily available to decision makers, stakeholders and the general public. The work on the Catalogue began in 2011, and was then further supported by the Icelandic government and the EU. The Catalogue forms a part of an integrated volcanic risk assessment project in Iceland (commenced in 2012), and the EU FP7 project FUTUREVOLC (2012-2016), establishing an Icelandic volcano Supersite. The Catalogue is a collaborative effort between the Icelandic Meteorological Office (the state volcano observatory), the Institute of Earth Sciences at the University of Iceland, and the Icelandic Civil Protection, with contributions from a large number of specialists in Iceland and elsewhere. The catalogue is scheduled for opening in the first half of 2015 and once completed, it will be an official publication intended to serve as an accurate and up to date source of information about active volcanoes in Iceland and their characteristics. The Catalogue is an open web resource in English and is composed of individual chapters on each of the volcanic systems. The chapters include information on the geology and structure of the volcano; the eruption history, pattern and products; the known precursory signals

  12. Progresses in geology and hazards analysis of Tianchi Volcano

    Institute of Scientific and Technical Information of China (English)

    WEI Hai-quan; JIN Bo-lu; LIU Yong-shun


    A number of different lahars have been recognized from a systematic survey of a mapping project. The high setting temperature feature of the deposits indicates a relationship between the lahar and the Millennium eruption event of Tianchi Volcano. The lahars caused a dramatic disaster. Recognize of the huge avalanche scars and deposits around Tianchi Volcano imply another highly destructive hazard. Three types of different texture of the avalanche deposits have been recognized. There was often magma mixing processes during the Millennium eruption of Tianchi Volcano, indicating a mixing and co-eruption regime of the eruption.

  13. Survey of Potential Geothermal Exploration Sites at Newberry Volcano Deschutes County, Oregon.

    Energy Technology Data Exchange (ETDEWEB)

    Priest, George R.; Vogt, Beverly F.; Black, Gerald L.


    The study summarizes the current data, generates some new data, and recommends further steps which should be taken to investigate the electrical power production potential of Newberry volcano. The objective was to concentrate on data from the developable flanks of the volcano. All previous data on the geology, hydrology, and geophysics were summarized. A soil-mercury survey focused on the flanks of the volcano was conducted. Samples from 1000 km/sup 2/ of the volcano were analyzed for mercury content. All this information was utilized to evaluate (1) the likelihood of future discovery of electrical-quality geothermal fluids on the flanks, and (2) the most cost-effective means of improving the quality of available power generation estimates for the volcano. 37 figures.

  14. Volcano-hazard zonation for San Vicente volcano, El Salvador (United States)

    Major, J.J.; Schilling, S.P.; Pullinger, C.R.; Escobar, C.D.; Howell, M.M.


    San Vicente volcano, also known as Chichontepec, is one of many volcanoes along the volcanic arc in El Salvador. This composite volcano, located about 50 kilometers east of the capital city San Salvador, has a volume of about 130 cubic kilometers, rises to an altitude of about 2180 meters, and towers above major communities such as San Vicente, Tepetitan, Guadalupe, Zacatecoluca, and Tecoluca. In addition to the larger communities that surround the volcano, several smaller communities and coffee plantations are located on or around the flanks of the volcano, and major transportation routes are located near the lowermost southern and eastern flanks of the volcano. The population density and proximity around San Vicente volcano, as well as the proximity of major transportation routes, increase the risk that even small landslides or eruptions, likely to occur again, can have serious societal consequences. The eruptive history of San Vicente volcano is not well known, and there is no definitive record of historical eruptive activity. The last significant eruption occurred more than 1700 years ago, and perhaps long before permanent human habitation of the area. Nevertheless, this volcano has a very long history of repeated, and sometimes violent, eruptions, and at least once a large section of the volcano collapsed in a massive landslide. The oldest rocks associated with a volcanic center at San Vicente are more than 2 million years old. The volcano is composed of remnants of multiple eruptive centers that have migrated roughly eastward with time. Future eruptions of this volcano will pose substantial risk to surrounding communities.

  15. Experimental Study on High Electrical Breakdown of Water Dielectric

    Institute of Scientific and Technical Information of China (English)

    Zhang Zicheng; Zhang Jiande; Yang Jianhua


    By means of a coaxial apparatus, pressurized water breakdown experiments with microsecond charging have been carried out with different surface roughness of electrodes and different ethylene glycol concentrations of ethylene glycol/water mixture. The experimental results about the breakdown stress and the effective time are presented. The breakdown stress is normalized to the situation that the effective time is transformed to 1 μs and analyzed. The conclusions are as follows: (1) the breakdown stress formula is modified to E = 0.561MA-1/10t-1eff/NP1/8; (2)the coefficient M is significantly increased by surface polishing and ethylene glycol additive; (3) it is accumulative for the capacity of improving electrical breakdown strength for surface polishing,ethylene glycol additive, and pressurization, of which pressurization is the most effective method;(4) the highest stress of 235.5 kV/cm is observed in ethylene glycol/water mixture with an ethylene glycol concentration of 80% at a hydrostatic pressure of 1215.9 kPa and is about one time greater than that in pure water at constant pressure; (5) for pressurization and surface pohshing,the primary mechanism to improve the breakdown strength of water dielectric is the increase in the breakdown time delay. Research results indicate great potential in the application of the high power pulse conditioning system of water dielectric.

  16. Review of Adult Electrical Burn Injury Outcomes Worldwide: An Analysis of Low-Voltage vs High-Voltage Electrical Injury. (United States)

    Shih, Jessica G; Shahrokhi, Shahriar; Jeschke, Marc G

    The aims of this article are to review low-voltage vs high-voltage electrical burn complications in adults and to identify novel areas that are not recognized to improve outcomes. An extensive literature search on electrical burn injuries was performed using OVID MEDLINE, PubMed, and EMBASE databases from 1946 to 2015. Studies relating to outcomes of electrical injury in the adult population (≥18 years of age) were included in the study. Forty-one single-institution publications with a total of 5485 electrical injury patients were identified and included in the present study. Fourty-four percent of these patients were low-voltage injuries (LVIs), 38.3% high-voltage injuries (HVIs), and 43.7% with voltage not otherwise specified. Forty-four percentage of studies did not characterize outcomes according to LHIs vs HVIs. Reported outcomes include surgical, medical, posttraumatic, and others (long-term/psychological/rehabilitative), all of which report greater incidence rates in HVI than in LVI. Only two studies report on psychological outcomes such as posttraumatic stress disorder. Mortality rates from electrical injuries are 2.6% in LVI, 5.2% in HVI, and 3.7% in not otherwise specified. Coroner's reports revealed a ratio of 2.4:1 for deaths caused by LVI compared with HVI. HVIs lead to greater morbidity and mortality than LVIs. However, the results of the coroner's reports suggest that immediate mortality from LVI may be underestimated. Furthermore, on the basis of this analysis, we conclude that the majority of studies report electrical injury outcomes; however, the majority of them do not analyze complications by low vs high voltage and often lack long-term psychological and rehabilitation outcomes after electrical injury indicating that a variety of central aspects are not being evaluated or assessed.

  17. Analysis of Electric Vehicle DC High Current Conversion Technology (United States)

    Yang, Jing; Bai, Jing-fen; Lin, Fan-tao; Lu, Da


    Based on the background of electric vehicles, it is elaborated the necessity about electric energy accurate metering of electric vehicle power batteries, and it is analyzed about the charging and discharging characteristics of power batteries. It is needed a DC large current converter to realize accurate calibration of power batteries electric energy metering. Several kinds of measuring methods are analyzed based on shunts and magnetic induction principle in detail. It is put forward power batteries charge and discharge calibration system principle, and it is simulated and analyzed ripple waves containing rate and harmonic waves containing rate of power batteries AC side and DC side. It is put forward suitable DC large current measurement methods of power batteries by comparing different measurement principles and it is looked forward the DC large current measurement techniques.

  18. High-altitude electrical discharges associated with thunderstorms and lightning (United States)

    Liu, Ningyu; McHarg, Matthew G.; Stenbaek-Nielsen, Hans C.


    The purpose of this paper is to introduce electrical discharge phenomena known as transient luminous events above thunderstorms to the lightning protection community. Transient luminous events include the upward electrical discharges from thunderstorms known as starters, jets, and gigantic jets, and electrical discharges initiated in the lower ionosphere such as sprites, halos, and elves. We give an overview of these phenomena with a focus on starters, jets, gigantic jets, and sprites, because similar to ordinary lightning, streamers and leaders are basic components of these four types of transient luminous events. We present a few recent observations to illustrate their main properties and briefly review the theories. The research in transient luminous events has not only advanced our understanding of the effects of thunderstorms and lightning in the middle and upper atmosphere, but also improved our knowledge of basic electrical discharge processes critical for sparks and lightning.

  19. Scandate Cathode for High Power Long Life Electric Propulsion Project (United States)

    National Aeronautics and Space Administration — Scandate cathodes are proposed as a way to boost performance and life for electric space propulsion systems. This company has recently demonstrated breakthrough...

  20. High Power Electric Propulsion for Outer Planet Missions (United States)

    Donahue, Benjamin B.


    Focused technology trade studies for Nuclear Electric Propulsion vehicle concepts for outer planet missions are presented; representative mission, vehicle and technology characterizations illustrate samples of work done under the NASA Marshall Space Flight Center-Boeing-SAIC In-Space Technology Assessment (ISTA) contract. An objective of ISTA is to identify and present sound technical and programtic options for the formulation and implementation of advanced electric and chemical propulsion solar system exploration missions. Investigations to date include a variety of outer planet destinations, trip times, science payload allotments, orbital capture techniques, all conducted to illustrate how advanced technology would maximize mission benefits. Architecture wide optimizations that facilitate good propulsion technology investments for advanced electric and chemical propulsion systems were conducted, including those relevant to the nuclear system initiative. Representative analyses of vehicles utilizing fission reactors with advanced power generation, Conversion, processing and electric propulsion systems, which would enable scientifically rich robotic exploration missions, are presented.

  1. Electrical conductivity of rocks at high pressures and temperatures (United States)

    Parkhomenko, E. I.; Bondarenko, A. T.


    The results of studies of the electrical conductivity in the most widely distributed types of igneous rocks, at temperatures of up to 1200 C, at atmospheric pressure, and also at temperatures of up to 700 C and at pressures of up to 20,000 kg/sq cm are described. The figures of electrical conductivity, of activaation energy and of the preexponential coefficient are presented and the dependence of these parameters on the petrochemical parameters of the rocks are reviewed. The possible electrical conductivities for the depository, granite and basalt layers of the Earth's crust and of the upper mantle are presented, as well as the electrical conductivity distribution to the depth of 200 to 240 km for different geological structures.

  2. Geology of Kilauea volcano

    Energy Technology Data Exchange (ETDEWEB)

    Moore, R.B. (Geological Survey, Denver, CO (United States). Federal Center); Trusdell, F.A. (Geological Survey, Hawaii National Park, HI (United States). Hawaiian Volcano Observatory)


    This paper summarizes studies of the structure, stratigraphy, petrology, drill holes, eruption frequency, and volcanic and seismic hazards of Kilauea volcano. All the volcano is discussed, but the focus is on its lower east rift zone (LERZ) because active exploration for geothermal energy is concentrated in that area. Kilauea probably has several separate hydrothermal-convection systems that develop in response to the dynamic behavior of the volcano and the influx of abundant meteoric water. Important features of some of these hydrothermal-convection systems are known through studies of surface geology and drill holes. Observations of eruptions during the past two centuries, detailed geologic mapping, radiocarbon dating, and paleomagnetic secular-variation studies indicate that Kilauea has erupted frequently from its summit and two radial rift zones during Quaternary time. Petrologic studies have established that Kilauea erupts only tholeiitic basalt. Extensive ash deposits at Kilauea's summit and on its LERZ record locally violent, but temporary, disruptions of local hydrothermal-convection systems during the interaction of water or steam with magma. Recent drill holes on the LERZ provide data on the temperatures of the hydrothermal-convection systems, intensity of dike intrusion, porosity and permeability, and an increasing amount of hydrothermal alteration with depth. The prehistoric and historic record of volcanic and seismic activity indicates that magma will continue to be supplied to deep and shallow reservoirs beneath Kilauea's summit and rift zones and that the volcano will be affected by eruptions and earthquakes for many thousands of years. 71 refs., 2 figs.

  3. Electrical Capacitance Volume Tomography with High-Contrast Dielectrics (United States)

    Nurge, Mark


    The Electrical Capacitance Volume Tomography (ECVT) system has been designed to complement the tools created to sense the presence of water in nonconductive spacecraft materials, by helping to not only find the approximate location of moisture but also its quantity and depth. The ECVT system has been created for use with a new image reconstruction algorithm capable of imaging high-contrast dielectric distributions. Rather than relying solely on mutual capacitance readings as is done in traditional electrical capacitance tomography applications, this method reconstructs high-resolution images using only the self-capacitance measurements. The image reconstruction method assumes that the material under inspection consists of a binary dielectric distribution, with either a high relative dielectric value representing the water or a low dielectric value for the background material. By constraining the unknown dielectric material to one of two values, the inverse math problem that must be solved to generate the image is no longer ill-determined. The image resolution becomes limited only by the accuracy and resolution of the measurement circuitry. Images were reconstructed using this method with both synthetic and real data acquired using an aluminum structure inserted at different positions within the sensing region. The cuboid geometry of the system has two parallel planes of 16 conductors arranged in a 4 4 pattern. The electrode geometry consists of parallel planes of copper conductors, connected through custom-built switch electronics, to a commercially available capacitance to digital converter. The figure shows two 4 4 arrays of electrodes milled from square sections of copper-clad circuit-board material and mounted on two pieces of glass-filled plastic backing, which were cut to approximately square shapes, 10 cm on a side. Each electrode is placed on 2.0-cm centers. The parallel arrays were mounted with the electrode arrays approximately 3 cm apart. The open ends

  4. The Electrical Conductivity of Gabbro at High Temperature and High Pressure

    Institute of Scientific and Technical Information of China (English)


    The electric conductivity of gabbro has been measured at 1.0-2.0 Gpa and 320-700℃,and the conduction mechanism has been analyzed in terms of the impedance spectra.Experimental results indicated that the electric conductivity depends on the frequency of alter-native current.Impedance arcs representing the conduction mechanism of grain interiors are displayed in the complex impedance plane ,and the mechanism is dominated at high pressure.These arcs occur over the range of 102-k×105Hz(k is the positive integer from 1 to 9) .On the basis of our results and previous work,it is concluded that gabbro cannot form any high conductivity layer (HCL) in the middle-lower crust.

  5. The Electrical Conductivity of Gabbro at High Temperature and High Pressure

    Institute of Scientific and Technical Information of China (English)

    王多君; 李和平; 易丽; 张卫刚; 刘丛强; 苏根利; 丁东业


    The electric conductivity of gabbro has been measured at 1.0 - 2.0 GPa and 320-700℃, and the conduction mechanism has been analyzed in terms of the impedance spectra.Experimental results indicated that the electric conductivity depends on the frequency of alternative current. Impedance arcs representing the conduction mechanism of grain interiors are displayed in the complex impedance plane, and the mechanism is dominated at high pressure.These arcs occur over the range of 102 - k× 105 Hz (k is the positive integer from 1 to 9). On the basis of our results and previous work, it is concluded that gabbro cannot form any high conductivity layer (HCL) in the middle-lower crust.

  6. High speed electric motors based on high performance novel soft magnets (United States)

    Silveyra, J. M.; Leary, A. M.; DeGeorge, V.; Simizu, S.; McHenry, M. E.


    Novel Co-based soft magnetic materials are presented as a potential substitute for electrical steels in high speed motors for current industry applications. The low losses, high permeabilities, and good mechanical strength of these materials enable application in high rotational speed induction machines. Here, we present a finite element analysis of Parallel Path Magnetic Technology rotating motors constructed with both silicon steel and Co-based nanocomposite. The later achieved a 70% size reduction and an 83% reduction on NdFeB magnet volume with respect to a similar Si-steel design.

  7. Pairing the Volcano

    CERN Document Server

    Ionica, Sorina


    Isogeny volcanoes are graphs whose vertices are elliptic curves and whose edges are $\\ell$-isogenies. Algorithms allowing to travel on these graphs were developed by Kohel in his thesis (1996) and later on, by Fouquet and Morain (2001). However, up to now, no method was known, to predict, before taking a step on the volcano, the direction of this step. Hence, in Kohel's and Fouquet-Morain algorithms, many steps are taken before choosing the right direction. In particular, ascending or horizontal isogenies are usually found using a trial-and-error approach. In this paper, we propose an alternative method that efficiently finds all points $P$ of order $\\ell$ such that the subgroup generated by $P$ is the kernel of an horizontal or an ascending isogeny. In many cases, our method is faster than previous methods. This is an extended version of a paper published in the proceedings of ANTS 2010. In addition, we treat the case of 2-isogeny volcanoes and we derive from the group structure of the curve and the pairing ...


    If the presently installed three-phase ac transmission system on aircraft were replaced by a higher voltage dc ( HVDC ) transmission using a ground...from one- to two-thirds of the total electrical system weight. HVDC may have some disadvantages such as higher short-circuit currents, some increase in

  9. A Novel, High Energy-Density Electrical Storage Device for Electric Weapons (United States)


    18 I. Task Objectives The primary object of the Phase I effort was to design a Million...field, which drives current at the voltage needed to power a variety of electric weapons such railguns, coilguns , and directed energy devices. Three... inductive , double ring circuit. Tremendous repulsion forces are exerted on the rings when the current circulation reaches Meg-Amp current levels. One


    Directory of Open Access Journals (Sweden)

    S. G. Pugacheva


    Full Text Available In article the basic geological and morphological features of a volcanic relief of a surface of a planet Mars are considered. The volcanic relief of a planet represents relic ancient shield volcanoes, linear forms of volcanic mountains, areal and central lava flooding, radial and concentric breaks. Results of researches of morphology of volcanic and tectonic formations of a relief of Mars are given in article. On materials of shooting of a surface of Mars spacecrafts constructed hypsometric high-rise profiles of volcanoes and average steepness of slopes are defined. The relative age of volcanoes and volcanic plains is estimated on density of shock craters.

  11. Ultrahigh Oxidation Resistance and High Electrical Conductivity in Copper-Silver Powder (United States)

    Li, Jiaxiang; Li, Yunping; Wang, Zhongchang; Bian, Huakang; Hou, Yuhang; Wang, Fenglin; Xu, Guofu; Liu, Bin; Liu, Yong


    The electrical conductivity of pure Cu powder is typically deteriorated at elevated temperatures due to the oxidation by forming non-conducting oxides on surface, while enhancing oxidation resistance via alloying is often accompanied by a drastic decline of electrical conductivity. Obtaining Cu powder with both a high electrical conductivity and a high oxidation resistance represents one of the key challenges in developing next-generation electrical transferring powder. Here, we fabricate a Cu-Ag powder with a continuous Ag network along grain boundaries of Cu particles and demonstrate that this new structure can inhibit the preferential oxidation in grain boundaries at elevated temperatures. As a result, the Cu-Ag powder displays considerably high electrical conductivity and high oxidation resistance up to approximately 300 °C, which are markedly higher than that of pure Cu powder. This study paves a new pathway for developing novel Cu powders with much enhanced electrical conductivity and oxidation resistance in service.

  12. High-spatial-resolution imagery helps map deposits of the large (VEI 4) 2010 Merapi Volcano eruption and their impact (United States)

    Solikhin, Akhmad; Thouret, Jean-Claude; Liew, Soo Chin; Gupta, Avijit; Sayudi, Dewi Sri; Oehler, Jean-François; Kassouk, Zeineb


    The 26 October-23 November 2010 eruption is Merapi's largest event (VEI 4) over the past 140 years. We used high-spatial-resolution (HSR) imagery from GeoEye, Pléiades, IKONOS, and SPOT5 satellites to assess the extent and effects of the pyroclastic density currents (PDCs) and subsequent lahars. We have tracked the geomorphic and structural (fracturing) changes of Merapi's summit crater and dome between 2008 and 2012. The 4 September 2011 GeoEye image shows that due to the explosive eruption, the summit area lost about 10 × 106 m3. The eruption enlarged the SSE-trending Gendol breach to be 1.3 × 0.3 × 0.2 km. The 2010 tephra and PDC deposits covered about 26 km2 in the two catchments of Gendol and Opak Rivers on Merapi's south flank, i.e., 60-75 % of the total PDC deposit area, with a total bulk volume of 45 × 106 m3. The tephra-fall deposit covered an area of about 1300 km2 with a range in volume of 18-21 × 106 m3. Supervised and object-oriented classification on HSR imagery enables us to map in detail the PDC deposits across the Gendol-Opak catchment. We delineated 16 spectrally and/or texturally distinct units of PDC deposits and compared them with previously published results. They encompass high-energy surge deposits within ca. 8 km of the summit, valley-confined PDC deposits channeled as far as 16.5 km in the Gendol River, and widespread overbank PDC with ash-cloud surge deposits on valley margins.

  13. Impedance spectroscopy analysis on electrical properties of serpentine at high pressure and high temperature

    Institute of Scientific and Technical Information of China (English)

    ZHU; Maoxu; (


    [1]Stesky, R. M., Brace, W. F., Electrical conductivity of serpentinized rocks to 6 kilobar, J. Geophys. Res., 1973, 78 (32): 7614-7621.[2]Zhu Maoxu, Xie Hongsen, Experimental studies on electrical properties of materials in the earth's interior, Advancement in Geosciences (in Chinese), 1998, 13(5): 438-446.[3]Roberts, J. J., Tyburczy, J. A., Frequency dependent electrical properties of polycrystalline olivine compacts, J. Geophys. Res., 1991, 96 (B10): 16205-16222.[4]Roberts, J. J., Tyburczy, J. A., Frequency dependent electrical properties of minerals and partial-melts, Surv. Geophys., 1994, 15: 239-262.[5]Huebner, I. S., Dillenburg, R. G., Impedance spectra of hot, dry silicate minerals and rock: Qualitative interpretation of spectra, Amer. Mineral, 1995, 80: 46-64.[6]Kavner, A., Li, X-Y, Jeanloz, R., Electrical conductivity of a natural (Mg, Fe)SiO3 majorite garnet, Geophys. Res. Lett., 1995, 22 (22): 3103-3106.[7]Hicks, T. L., Secco, R., Dehydration and decomposition of pyrophyllite at high pressure: Electrical conductivity and X-ray diffraction studies to 5 Gpa, Can. J. Earth Sci., 1997, 34: 875-882.[8]Li, X-Y, Jeanloz, R., Effect of iron content on the electrical conductivity of perovskite and magnesiowustite assemblages at lower mantle condition, J. Geophys. Res., 1991, 96(B4): 6113-6120.[9]Xie Hongsen, Introduction to the Materials in the Earth's Interior (in Chinese), Beijing: Science Press, 1997, 42-53.[10] Tatsurmi, Y., Migration of fluid phase and genesis of basalt magmas in subduction zone, J. Geophys. Res., 1989, 94: 4697-4707.[11] Duba, A., Huenges, G., Nover, E. et al., Impedance of black shale from munsterland 1 borehole: An anomalously good conductor? Geophys. J., 1988, 94: 413-419.[12] Watanabe, T., Kurita, K., The relationship between electrical conductivity and melt fraction in a partially molten simple system: Archies's law behavior, Phys. Earth Planet Inter., 1993, 78: 9-17.[13] Macdonald

  14. Analysis of predictor factors of limb amputation in patients with high-voltage electrical burns



    Background: Limb amputation is considered one of the most devastating consequences of electrical injury. Any factors that correlate with the degree of muscle damage can be used to predict the necessity of limb amputation. The aim of this study was to determine the factors that can be used to predict limb amputation in high-voltage electrically injured patients. Methods: Eighty-two high-voltage electrically injured patients were admitted to the Department of Plastic and Reconstructive Surg...

  15. [Transient high frequency nodal rhythm after a high voltage electric shock. Report of one case]. (United States)

    Supervía, August; Del Baño, Francisco; Aguirre, Alfons; Membrilla, Estela


    Electrical shock can cause a direct myocardial damage and different types of arrhythmias, which are uncommon and occur more often when there is a high voltage exposure. We report a 19-year-old male that received a high voltage shock, falling thereafter from an altitude of four meters. On admission to the emergency room, he had second and third degree burns in the right hand and the left thigh. The electrocardiogram showed a nodal rhythm of 72 beats per minute. After four hours of monitoring, sinus rhythm returned spontaneously.

  16. Review of the Dynamics of Coalescence and Demulsification by High-Voltage Pulsed Electric Fields

    Directory of Open Access Journals (Sweden)

    Ye Peng


    Full Text Available The coalescence of droplets in oil can be implemented rapidly by high-voltage pulse electric field, which is an effective demulsification dehydration technological method. At present, it is widely believed that the main reason of pulse electric field promoting droplets coalescence is the dipole coalescence and oscillation coalescence in pulse electric field, and the optimal coalescence pulse electric field parameters exist. Around the above content, the dynamics of high-voltage pulse electric field promoting the coalescence of emulsified droplets is studied by researchers domestically and abroad. By review, the progress of high-voltage pulse electric field demulsification technology can get a better understanding, which has an effect of throwing a sprat to catch a whale on promoting the industrial application.

  17. The petrological relationship between Kamen volcano and adjacent volcanoes of Klyuchevskaya group (United States)

    Churikova, Tatiana; Gordeychik, Boris; Wörner, Gerhard; Ivanov, Boris; Maximov, Alexander; Lebedev, Igor; Griban, Andrey


    The Klyuchevskaya Group (KG) of volcanoes has the highest magma production rate across the Kamchatka arc and in fact for any arc worldwide. However, modern geochemical studies of Kamen volcano, which is located between Klyuchevskoy, Bezymianny and Ploskie Sopky volcanoes, were not carried out and its relation and petrogenesis in comparison to other KG volcanoes is unknown. Space-time proximity of KG volcanoes and the common zone of seismicity below them may suggest a common source and genetic relationship. However, the lavas of neighboring volcanoes are rather different: high-Mg and high-Al basalts occur at Klyuchevskoy volcano, Hbl-bearing andesites and dаcites dominate at Bezymianny and medium-high-K subalkaline rocks at Ploskie Sopky volcano. Moreover, previously it was shown that distinct fluid signatures were observed in different KG volcanoes. In this report we present geological, petrographical, mineralogical and petrochemical data on the rocks of Kamen volcano in comparison with other KG volcanoes. Three consecutive periods of volcano activity were recognized in geological history of Kamen volcano: stratovolcano formation, development of a dike complex and formation of numerous cinder and cinder-lava monogenetic cones. The rock series of volcano are divided into four groups: olivine-bearing (Ol-2Px and Ol-Cpx), olivine-free (2Px-Pl, Cpx-Pl and abundant Pl), Hb-bearing and subaphyric rocks. While olivine-bearing rocks are observed in all volcanic stages, olivine-free lavas are presented only in the stratovolcano edifice. Lavas of the monogenetic cones are presented by olivine-bearing and subaphyric rocks. Dikes are olivine-bearing and hornblende-bearing rocks. Olivines of the Kamen stratovolcano and dikes vary from Fo60 to Fo83, clinopyroxenes are augites in composition and plagioclases have a bimodal distribution with maximum modes at An50 and An86. Oxides are represented by high-Al spinel, magnetite and titaniferous magnetite. Mineral compositions of the

  18. The solar electric propulsion stage concept for high energy missions. (United States)

    Guttman, C. H.; Gilbert, J.; Horio, S. P.; Richardson, E. H.


    Definition of multimission and engine performance requirements for candidate solar electric propulsion stage configurations, considering launch vehicle compatibility, electric propulsion integration, payload requirements, and the effects of environmental extremes. Electric propulsion power options include two solar array power levels (15/22 kW), up to twelve electric thrustors of 30 cm diameter and 2.7 kW each, five to eight power conditioning units, and a maximum mercury propellant capacity of 1530 kg. In performance, the stage with a dry weight of 700 to 900 kg can deliver a net mass of 756 kg into Saturn orbit, 329 kg into a tight Mercury orbit, and 334 kg within 0.1 AU of the sun. The stage can also deliver a round trip payload of 3350 kg to geosynchronous orbit and return from an intermediate elliptical orbit using the Shuttle/Tug. Thus, a versatile stage is developed which competes effectively in performance with existing integrated spacecraft and promises considerable savings in total program costs.

  19. Segregated Planktonic and Bottom-Dwelling Archaeal Communities in High-Temperature Acidic/Sulfuric Ponds of the Tatun Volcano Group, Northern Taiwan


    Ting-Wen Cheng; Pei-Ling Wang; Sheng-Rong Song; Li-Hung Lin


    Geothermal environments are characterized by dynamic redox and temperature fluctuations inherited from the exposure of deeply-sourced, hot, reducing fluids to low-temperature, oxidizing ambient environments. To investigate whether microbial assemblages shifted in response to the changes of a redox state within acidic hot ponds, we collected three paired water and sediment samples from the Tatun Volcano Group, assessed metabolic roles of community members, and correlated their functional capab...

  20. Volcano monitoring with an infrared camera: first insights from Villarrica Volcano (United States)

    Rosas Sotomayor, Florencia; Amigo Ramos, Alvaro; Velasquez Vargas, Gabriela; Medina, Roxana; Thomas, Helen; Prata, Fred; Geoffroy, Carolina


    This contribution focuses on the first trials of the, almost 24/7 monitoring of Villarrica volcano with an infrared camera. Results must be compared with other SO2 remote sensing instruments such as DOAS and UV-camera, for the ''day'' measurements. Infrared remote sensing of volcanic emissions is a fast and safe method to obtain gas abundances in volcanic plumes, in particular when the access to the vent is difficult, during volcanic crisis and at night time. In recent years, a ground-based infrared camera (Nicair) has been developed by Nicarnica Aviation, which quantifies SO2 and ash on volcanic plumes, based on the infrared radiance at specific wavelengths through the application of filters. Three Nicair1 (first model) have been acquired by the Geological Survey of Chile in order to study degassing of active volcanoes. Several trials with the instruments have been performed in northern Chilean volcanoes, and have proven that the intervals of retrieved SO2 concentration and fluxes are as expected. Measurements were also performed at Villarrica volcano, and a location to install a ''fixed'' camera, at 8km from the crater, was discovered here. It is a coffee house with electrical power, wifi network, polite and committed owners and a full view of the volcano summit. The first measurements are being made and processed in order to have full day and week of SO2 emissions, analyze data transfer and storage, improve the remote control of the instrument and notebook in case of breakdown, web-cam/GoPro support, and the goal of the project: which is to implement a fixed station to monitor and study the Villarrica volcano with a Nicair1 integrating and comparing these results with other remote sensing instruments. This works also looks upon the strengthen of bonds with the community by developing teaching material and giving talks to communicate volcanic hazards and other geoscience topics to the people who live "just around the corner" from one of the most active volcanoes

  1. Correlation of Electrical Noise with Non-radiative Current for High Power QWLs

    Institute of Scientific and Technical Information of China (English)


    The characteristics of low-frequency electrical noise, voltage-current (V-I) and electrical derivation for 980nm InGaAsP/InGaAs/GaAs high power double quantum well lasers(DQWLs) are measured under different conditions. The correlation of the low-frequency electrical noise with surface non-radiative current of devices is discussed. The results indicate the low-frequency electrical noise of 980nm DQWLs with high power is mainly 1/f noise and has good relation with the device surface current at low injection.

  2. Self-resonant Coil for Contactless Electrical Conductivity Measurement under Pulsed Ultra-high Magnetic Fields

    CERN Document Server

    Nakamura, Daisuke; Takeyama, Shojiro


    In this study, we develop experimental apparatus for contactless electrical conductivity measurements under pulsed high magnetic fields over 100 T using a self-resonant-type high-frequency circuit. The resonant power spectra were numerically analyzed, and the conducted simulations showed that the apparatus is optimal for electrical conductivity measurements of materials with high electrical conductivity. The newly developed instruments were applied to a high-temperature cuprate superconductor La$_{2-x}$Sr$_x$CuO$_4$ to show conductivity changes in magnetic fields up to 102 T with a good signal-to-noise ratio. The upper critical field was determined with high accuracy.

  3. High Energy Density and High Temperature Multilayer Capacitor Films for Electric Vehicle Applications (United States)

    Treufeld, Imre; Song, Michelle; Zhu, Lei; Baer, Eric; Snyder, Joe; Langhe, Deepak


    Multilayer films (MLFs) with high energy density and high temperature capability (>120 °C) have been developed at Case Western Reserve University. Such films offer a potential solution for electric car DC-link capacitors, where high ripple currents and high temperature tolerance are required. The current state-of-the-art capacitors used in electric cars for converting DC to AC use biaxially oriented polypropylene (BOPP), which can only operate at temperatures up to 85 °C requiring an external cooling system. The polycarbonate (PC)/poly(vinylidene fluoride) (PVDF) MLFs have a higher permittivity compared to that of BOPP (2.3), leading to higher energy density. They have good mechanical stability and reasonably low dielectric losses at 120 °C. Nonetheless, our preliminary dielectric measurements show that the MLFs exhibit appreciable dielectric losses (20%) at 120 °C, which would, despite all the other advantages, make them not suitable for practical applications. Our preliminary data showed that dielectric losses of the MLFs at 120 °C up to 400 MV/m and 1000 Hz originate mostly from impurity ionic conduction. This work is supported by the NSF PFI/BIC Program (IIP-1237708).

  4. Ruiz Volcano: Preliminary report (United States)

    Ruiz Volcano, Colombia (4.88°N, 75.32°W). All times are local (= GMT -5 hours).An explosive eruption on November 13, 1985, melted ice and snow in the summit area, generating lahars that flowed tens of kilometers down flank river valleys, killing more than 20,000 people. This is history's fourth largest single-eruption death toll, behind only Tambora in 1815 (92,000), Krakatau in 1883 (36,000), and Mount Pelée in May 1902 (28,000). The following briefly summarizes the very preliminary and inevitably conflicting information that had been received by press time.

  5. Redoubt Volcano: 2009 Eruption Overview (United States)

    Bull, K. F.


    observed on the crater rim and upper glacier on the south flank. After April 4, the volcano moved into a non-explosive period of dome building. Lava dome growth was tracked by satellite and thermal imagery and photogrammetry from web-camera and overflight images. Between April 4-June 9, the extrusion rate ranged from 35 m3/sec to 4 m3/sec. Seismicity and volcanic gas emissions remained high during this period. Estimated dome volume in mid-June was 68 M m3. August data suggest no further dome growth.

  6. Monitoring Thermal Activity of Eastern Anatolian Volcanoes Using MODIS Images (United States)

    Diker, Caner; Ulusoy, Inan


    MODIS (Moderate Resolution Imaging Spectroradiometer) instrument is used for imaging atmosphere, land and ocean with 36 bands. Both AQUA and TERRA platforms acquire 2 images daily (daytime and nighttime). Low temperature anomalies on volcanoes comprise important clues. Low temperature anomalies on Holocene volcanoes of Eastern Anatolia were investigated for these clues using MODIS Land Surface Temperature (LST) images. A total of 16800 daily LST images dated between 2001 and 2012 have been processed using a code written in IDL (Interactive Data Language). Factors like shadow, ice/snow and clouds that are affecting the reflectance data are masked. The mask is derived from MODIS reflectance data state image. Various LST images are calculated: Two nested region of interest (ROI) windows (square/rectangular) have been selected on the images. First is the bigger window, which covers the whole area of the volcano (Total volcano area). Second one is a smaller window which circumference the summit (crater and/or caldera) of the volcano (Summit cone) where thermal output is generally higher when compared to the flanks. Two data sets have been calculated using the ROI's for each volcano. The first set contains daytime and nighttime raw data without any correction. The second set contains topographically corrected images; daytime images are corrected using Cosine and Minnaert methods and nighttime images are corrected using three step normalization method. Calculated surface temperatures (Tmax, Tmin, Tmean) are plotted annually. On Nemrut Volcano as an example, maximum and minimum temperatures are between 26.31oC and -44.87oC on nighttime data for twelve years period. Temperature difference between total volcano area ROI and summit cone ROI are calculated (ΔT). High ΔT indicates that there is an increase of temperature at the summit cone when compared to the total volcano area. STA/LTA (Short Term Average/Long Term Average) filter was applied to maximum temperature and

  7. Electrical resistivity of coal-bearing rocks under high temperature and the detection of coal fires using electrical resistance tomography (United States)

    Shao, Zhenlu; Wang, Deming; Wang, Yanming; Zhong, Xiaoxing; Tang, Xiaofei; Xi, Dongdong


    Coal fires are severe hazards to environment, health and safety throughout the world. Efficient and economical extinguishing of these fires requires that the extent of the subsurface coal fires should be delineated. Electrical and electromagnetic methods have been used to detect coal fires in recent years. However, the resistivity change of coal-bearing rocks at high temperature is rarely investigated. The resistivity characteristics of coal fires at different temperatures and depths are seldomly researched as well. In this paper, we present the results of measurements of several coal-bearing rocks' resistivity and permeability under high temperature. Two major causes for the change in resistivity with increasing temperature are recognized, there are the increase of charge carriers and thermal fracturing, of which the first one is probably the dominant cause. A set of 2-D simulations is carried out to compare the relation of resolution and efficiency of coal fires detection to temperature and depth when adopting the electrical resistance tomography. The simulation results show that the resolution and efficiency decrease with the decrease of temperature and the increase of depth. Finally, the electrical resistance tomography is used to delineate coal fires in the Anjialing Open Pit Mine. Most low-resistivity regions are verified as coal-fire areas according to the long-term monitoring of borehole temperature. The results indicate that the electrical resistance tomography can be used as a tool for the detection of coal fires.

  8. [Accident risk perception in high-voltage electrical maintenance workers]. (United States)

    Micheli, M; Zanaletti, W; Giorgi, I; Argentero, P; Candura, S M


    Promoting safety at work represents a fundamental task for achieving improvement in the quality of working life and preventing accidental injuries at work. Nevertheless, over the last few decades injuries at work have continued to constitute a significant problem. The aim of this study was to examine accident risk perception in a sample of 45 subjects employed in the electricity sector and to relate their risk perception to personality characteristics, cognitive functioning, and personal and professional history. The instruments used were: "Cognitive Behavioral Assessment 2.0", the "Workplace safety questionnaire" (an Italian questionnaire on safety at work), and a battery of neuropsychological tests. Findings show that electricity (current variability) was perceived as the most serious risk factor, while the most frequent perceived risk factors for accidents were accidental falls, cuts and bruises. The subjects of our sample showed a good awareness of risk perception, and good mood response and augmented psychophysiological activation during accidental injuries.

  9. Electrical Conductivity of HgTe at High Temperatures (United States)

    Li, C.; Lehoczky, S. L.; Su, C.-H.; Scripa, R. N.


    The electrical conductivity of HgTe was measured using a rotating magnetic field method from 300 K to the melting point (943 K). A microscopic theory for electrical conduction was used to calculate the expected temperature dependence of the HgTe conductivity. A comparison between the measured and calculated conductivities was used to obtain the estimates of the temperature dependence of Gamma(sub 6)-Gamma(sub 8) energy gap from 300 K to 943 K. The estimated temperature coefficient for the energy gap was comparable to the previous results at lower temperatures (less than or equal to 300 K). A rapid increase in the conductivity just above 300 K and a subsequent decrease at 500 K is attributed to band crossover effects. This paper describes the experimental approach and some of the theoretical calculation details.

  10. Electric compressor with high-speed brushless DC motor; E-Kompressor mit buerstenlosem Gleichstrommotor

    Energy Technology Data Exchange (ETDEWEB)

    Biwersi, Stephan; Tavernier, Stephan; Equoy, Samuel [Moving Magnet Technologies (MMT), Besancon (France)


    Moving Magnet Technologies (MMT) from Besancon in France has developed a highly efficient brushless DC motor that is especially suitable for use in electrically supported compressors. It helps to further minimise so-called turbo lag in supercharged internal combustion engines. The following report presents technical details of the electric motor and practical results in combination with an electrically driven compressor. MMT was supported by Swissauto in designing the supercharging system.

  11. Magnetic liquids under high electric fields as optical diodes

    CERN Document Server

    Pereira, Jonas P; Smolyaninova, Vera N


    We show and give examples of how unidirectional propagation of light rays in the limit of geometric optics could arise in some magnetic fluids due to the magnetoelectric effect under weak DC magnetic fields and strong DC electric fields around half of their dielectric breakdown. For such liquids as kerosene and transformer oils, one-way propagation of light may occur for 30 nm diameter magnetic nanoparticles (e.g. cobalt) and concentrations of 2% or larger.

  12. Multipacting phenomenon at high electric fields of superconducting cavities

    Institute of Scientific and Technical Information of China (English)

    Zhu Feng; D.Proch; Hao Jian-Kui


    Recently multipacting(MP) recalculation of the TeV Energy Superconductiong Linear Accelerator (TESLA)resonator was performed. In addition to the normal MP which occurs at a peak electric field of around 40MV/m for the TESLA cavity, another type of multipacting with resonant electron trajectory that is far from the equator is also seen.It occurs at a gradient around 60MV/m to 70MV/m. This result seems to explain some experimental observations.

  13. Magnetic liquids under high electric fields as broadband optical diodes (United States)

    Pereira, Jonas P.; Smolyaninov, Igor I.; Smolyaninova, Vera N.


    We show that unidirectional propagation of light rays in the limit of geometric optics could arise in some magnetic fluids due to the magnetoelectric effect under weak DC magnetic fields and strong DC electric fields around half of their dielectric breakdown. For such liquids as kerosene and transformer oils, one-way propagation of light may occur for 30-nm-diameter magnetic nanoparticles (e.g., cobalt) and concentrations of 2 % or larger.

  14. High Penetration of Electrical Vehicles in Microgrids: Threats and Opportunities (United States)

    Khederzadeh, Mojtaba; Khalili, Mohammad


    Given that the microgrid concept is the building block of future electric distribution systems and electrical vehicles (EVs) are the future of transportation market, in this paper, the impact of EVs on the performance of microgrids is investigated. Demand-side participation is used to cope with increasing demand for EV charging. The problem of coordination of EV charging and discharging (with vehicle-to-grid (V2G) functionality) and demand response is formulated as a market-clearing mechanism that accepts bids from the demand and supply sides and takes into account the constraints put forward by different parts. Therefore, a day-ahead market with detailed bids and offers within the microgrid is designed whose objective is to maximize the social welfare which is the difference between the value that consumers attach to the electrical energy they buy plus the benefit of the EV owners participating in the V2G functionality and the cost of producing/purchasing this energy. As the optimization problem is a mixed integer nonlinear programming one, it is decomposed into one master problem for energy scheduling and one subproblem for power flow computation. The two problems are solved iteratively by interfacing MATLAB with GAMS. Simulation results on a sample microgrid with different residential, commercial and industrial consumers with associated demand-side biddings and different penetration level of EVs support the proposed formulation of the problem and the applied methods.

  15. Analysis of the 2006 block-and-ash flow deposits of Merapi Volcano, Java, Indonesia, using high-spatial resolution IKONOS images and complementary ground based observations (United States)

    Thouret, Jean-Claude; Gupta, Avijit; Liew, Soo Chin; Lube, Gert; Cronin, Shane J.; Surono, Dr


    On 16 June 2006 an overpass of IKONOS coincided with the emplacement of an active block-and-ash flow fed by a lava dome collapse event at Merapi Volcano (Java, Indonesia). This was the first satellite image recorded for a moving pyroclastic flow. The very high-spatial resolution data displayed the extent and impact of the pyroclastic deposits emplaced during and prior to, the day of image acquisition. This allowed a number of features associated with high-hazard block-and-ash flows emplaced in narrow, deep gorges to be mapped, interpreted and understood. The block-and-ash flow and surge deposits recognized in the Ikonos images include: (1) several channel-confined flow lobes and tongues in the box-shaped valley; (2) thin ash-cloud surge deposit and knocked-down trees in constricted areas on both slopes of the gorge; (3) fan-like over bank deposits on the Gendol-Tlogo interfluves from which flows were re-routed in the Tlogo secondary valley; (4) massive over bank lobes on the right bank from which flows devastated the village of Kaliadem 0.5 km from the main channel, a small part of this flow being re-channeled in the Opak secondary valley. The high-resolution IKONOS images also helped us to identify geomorphic obstacles that enabled flows to ramp and spill out from the sinuous channel, a process called flow avulsion. Importantly, the avulsion redirected flows to unexpected areas away from the main channel. In the case of Merapi we see that the presence of valley fill by previous deposits, bends and man-made dams influence the otherwise valley-guided course of the flows. Sadly, Sabo dams (built to ameliorate the effect of high sediment load streams) can actually cause block-and-ash flows to jump out of their containing channel and advance into sensitive areas. Very-high-spatial resolution satellite images are very useful for mapping and interpreting the distribution of freshly erupted volcanic deposits. IKONOS-type images with 1-m resolution provide opportunities to

  16. Three-dimensional shallow velocity structure beneath Taal Volcano, Philippines (United States)

    You, Shuei-Huei; Konstantinou, Konstantinos I.; Gung, Yuancheng; Lin, Cheng-Horng


    Based on its numerous historical explosive eruptions and high potential hazards to nearby population of millions, Taal Volcano is one of the most dangerous "Decade Volcanoes" in the world. To provide better investigation on local seismicity and seismic structure beneath Taal Volcano, we deployed a temporary seismic network consisting of eight stations from March 2008 to March 2010. In the preliminary data processing stage, three periods showing linear time-drifting of internal clock were clearly identified from noise-derived empirical Green's functions. The time-drifting errors were corrected prior to further data analyses. By using VELEST, 2274 local earthquakes were manually picked and located. Two major earthquake groups are noticed, with one lying beneath the western shore of Taal Lake showing a linear feature, and the other spreading around the eastern flank of Taal Volcano Island at shallower depths. We performed seismic tomography to image the 3D structure beneath Taal Volcano using the LOTOS algorithm. Some interesting features are revealed from the tomographic results, including a solidified magma conduit below the northwestern corner of Taal Volcano Island, indicated by high Vp, Vs, and low Vp/Vs ratio, and a large potential hydrothermal reservoir beneath the center of Taal Volcano Island, suggested by low Vs and high Vp/Vs ratio. Furthermore, combining earthquake distributions and tomographic images, we suggest potential existence of a hydrothermal reservoir beneath the southwestern corner of Taal Lake, and a fluid conduit extending to the northwest. These seismic features have never been proposed in previous studies, implying that new hydrothermal activity might be formed in places away from the historical craters on Taal Volcano Island.

  17. Distribution of acidic groundwater around quaternary volcanoes in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Asamori, Koichi; Ishimaru, Tsuneari; Iwatsuki, Teruki [Japan Nuclear Cycle Development Inst., Toki, Gifu (Japan). Tono Geoscience Center


    One important key issue in the understanding of the long-term stability of the geological environment is the influence of magmatism. In this study, we examined the general spatial distribution of acidic groundwater around Quaternary volcanoes in Japan using a database of groundwater geochemistry. The results may be summarized as follows: Acidic groundwater with pH < 4.8 mainly occur in present volcanic regions and are distributed from several kilometers to about 20 km from Quaternary volcanoes. The pH value of groundwater tends to decrease with increasing distance from a volcano. However, these results may be affected by inhomogeneity of groundwater data distribution and the characteristic activity of each volcano. In order to assess a specific volcanic region, a detailed analysis that considers volcanic activity, using a data set with high spatial density is necessary. (author)

  18. Volcano Monitoring Using Google Earth (United States)

    Cameron, W.; Dehn, J.; Bailey, J. E.; Webley, P.


    At the Alaska Volcano Observatory (AVO), remote sensing is an important component of its daily monitoring of volcanoes. AVO’s remote sensing group (AVORS) primarily utilizes three satellite datasets; Advanced Very High Resolution Radiometer (AVHRR) data, from the National Oceanic and Atmospheric Administration’s (NOAA) Polar Orbiting Satellites (POES), Moderate Resolution Imaging Spectroradiometer (MODIS) data from the National Aeronautics and Space Administration’s (NASA) Terra and Aqua satellites, and NOAA’s Geostationary Operational Environmental Satellites (GOES) data. AVHRR and MODIS data are collected by receiving stations operated by the Geographic Information Network of Alaska (GINA) at the University of Alaska’s Geophysical Institute. An additional AVHRR data feed is supplied by NOAA’s Gilmore Creek satellite tracking station. GOES data are provided by the Naval Research Laboratory (NRL), Monterey Bay. The ability to visualize these images and their derived products is critical for the timely analysis of the data. To this end, AVORS has developed javascript web interfaces that allow the user to view images and metadata. These work well for internal analysts to quickly access a given dataset, but they do not provide an integrated view of all the data. To do this AVORS has integrated its datasets with Keyhole Markup Language (KML) allowing them to be viewed by a number of virtual globes or other geobrowsers that support this code. Examples of AVORS’ use of KML include the ability to browse thermal satellite image overlays to look for signs of volcanic activity. Webcams can also be viewed interactively through KML to confirm current activity. Other applications include monitoring the location and status of instrumentation; near real-time plotting of earthquake hypocenters; mapping of new volcanic deposits using polygons; and animated models of ash plumes, created by a combination of ash dispersion modeling and 3D visualization packages.

  19. Elementary analysis of data from Tianchi Volcano

    Institute of Scientific and Technical Information of China (English)

    LIU Guo-ming; ZHANG Heng-rong; KONG Qing-jun; WU Cheng-zhi; GUO Feng; ZHANG Chao-fan


    Tianchi Volcano is the largest potential erupticve volcano in China. Analyzing these data on seismic monitoring, deformation observation and water chemistry investigation gained from the Tianchi Volcano Observatory (TVO), the authors consider that the Tianchi Volcano is in going into a new flourishing time.

  20. EARTHQUAKES - VOLCANOES (Causes - Forecast - Counteraction) (United States)

    Tsiapas, Elias


    Earthquakes and volcanoes are caused by: 1)Various liquid elements (e.g. H20, H2S, S02) which emerge from the pyrosphere and are trapped in the space between the solid crust and the pyrosphere (Moho discontinuity). 2)Protrusions of the solid crust at the Moho discontinuity (mountain range roots, sinking of the lithosphere's plates). 3)The differential movement of crust and pyrosphere. The crust misses one full rotation for approximately every 100 pyrosphere rotations, mostly because of the lunar pull. The above mentioned elements can be found in small quantities all over the Moho discontinuity, and they are constantly causing minor earthquakes and small volcanic eruptions. When large quantities of these elements (H20, H2S, SO2, etc) concentrate, they are carried away by the pyrosphere, moving from west to east under the crust. When this movement takes place under flat surfaces of the solid crust, it does not cause earthquakes. But when these elements come along a protrusion (a mountain root) they concentrate on its western side, displacing the pyrosphere until they fill the space created. Due to the differential movement of pyrosphere and solid crust, a vacuum is created on the eastern side of these protrusions and when the aforementioned liquids overfill this space, they explode, escaping to the east. At the point of their escape, these liquids are vaporized and compressed, their flow accelerates, their temperature rises due to fluid friction and they are ionized. On the Earth's surface, a powerful rumbling sound and electrical discharges in the atmosphere, caused by the movement of the gasses, are noticeable. When these elements escape, the space on the west side of the protrusion is violently taken up by the pyrosphere, which collides with the protrusion, causing a major earthquake, attenuation of the protrusions, cracks on the solid crust and damages to structures on the Earth's surface. It is easy to foresee when an earthquake will occur and how big it is

  1. Tensile and electrical properties of high-strength high-conductivity copper alloys

    Energy Technology Data Exchange (ETDEWEB)

    Zinkle, S.J.; Eatherly, W.S. [Oak Ridge National Lab., TN (United States)


    Electrical conductivity and tensile properties have been measured on an extruded and annealed CuCrNb dispersion strengthened copper alloy which has been developed for demanding aerospace high heat flux applications. The properties of this alloy are somewhat inferior to GlidCop dispersion strengthened copper and prime-aged CuCrZr over the temperature range of 20--500 C. However, if the property degradation in CuCrZr due to joining operations and the anisotropic properties of GlidCop in the short transverse direction are taken into consideration, CuCrNb may be a suitable alternative material for high heat flux structural applications in fusion energy devices. The electrical conductivity and tensile properties of CuCrZr that was solution annealed and then simultaneously aged and diffusion bonded are also summarized. A severe reduction in tensile elongation is observed in the diffusion bonded joint, particularly if a thin copper shim is not placed in the diffusion bondline.

  2. Research on High Temperature Ceramic Insulation for Electrical Conductors (United States)

    Kreidler, Eric R.; Bhallamudi, Vidya Praveen


    Three methods for applying ceramic coatings to wires were examined in depth and a fourth (chemical vapor deposition) was studied briefly. CVD coatings were not reported in the thesis because it was realized early in the study that the deposition rate of the coatings was too slow to be used in a commercial process. Of the methods reported in the thesis, slurry coating was the most promising. This method consists of slowly drawing a platinum wire through a thixotropic slurry of alumina in a vehicle composed of polyvinyl butyral, methyl ethyl ketone, and toluene. The coatings produced by this method were continuous and free of cracks after sintering. The sintered coatings crack when the wire is bent around sharp corners, but most of the coating remains in place and still provides electrical insulation between the wire and any metallic structure to which the wire may be attached. The coating thickness was 0.61 mm (16 micrometers). The electrical resistivity of the intact coating was 340 M-Ohm-cm at 800 C and 23 M-Ohm-cm at 1050 C. Therefore, these coatings more than meet the electrical requirements for use in turbine engines. Although adherence of the coating to the wire was generally excellent, a problem was noted in localized areas where the coating flaked off. Further work will be needed to obtain good coating adherence along the entire length of the wire. The next most promising coatings were made by electrophoretic deposition (EPD) of Al2O3 onto platinum wires, using mixtures of ethanol and acetone as the suspending liquid. These EPD coatings were made only on short lengths of wire because the coating is too fragile to allow spooling of the wire. The worst coatings were those made by electrophoretic deposition from aqueous suspensions. Continuous slurry coating of wire was achieved, but due to lack of suitable equipment, the wire had to be cut into short lengths for sintering.

  3. Electrical conductivity of molten SnCl{sub 2} at temperature as high as 1314 K

    Energy Technology Data Exchange (ETDEWEB)

    Salyulev, Alexander B.; Potapov, Alexei M. [Ural Branch of RAS, Ekaterinburg (Russian Federation). Inst. of High-Temperature Electrochemistry


    The electrical conductivity of molten SnCl{sub 2} was measured in a wide temperature range (ΔT=763 K), from 551 K to temperature as high as 1314 K, that is, 391 above the boiling point of the salt. The specific electrical conductance was found to reach its maximum at 1143 K, after that it decreases with the temperature rising.

  4. High performance nickel-cadmium cells for electric vehicles (United States)

    Cornu, Jean-Pierre

    A new concept of a cadmium electrode associated with a lighter nickel structure, a multi-cell module technology, allows the proposal of a very promisig alternative power source for electric vehicle (EV) batteries, the usable specific energy being 31% of the theoretical value. Every characteristic of this Ni-Cd module (i.e., specific energy and power, energy and power density, energy efficiency, life and reliability) gives the best performing EV battery, to date. Thus, with the efficient support of two major French car manufacturers and the French government, SAFT will launch, during Spring '95, the first pilot line of EV Ni-Cd module manufacturing.

  5. Multiwalled carbon nanotube/polydimethylsiloxane composite films as high performance flexible electric heating elements

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Jing; Jeong, Young Gyu, E-mail: [Department of Advanced Organic Materials and Textile System Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of)


    High performance elastomeric electric heating elements were prepared by incorporating various contents of pristine multiwalled carbon nanotube (MWCNT) in polydimethylsiloxane (PDMS) matrix by using an efficient solution-casting and curing technique. The pristine MWCNTs were identified to be uniformly dispersed in the PDMS matrix and the electrical percolation of MWCNTs was evaluated to be at ∼0.27 wt. %, where the electrical resistivity of the MWCNT/PDMS composite films dropped remarkably. Accordingly, the composite films with higher MWCNT contents above 0.3 wt. % exhibit excellent electric heating performance in terms of temperature response rapidity and electric energy efficiency at constant applied voltages. In addition, the composite films, which were thermally stable up to 250 °C, showed excellent heating-cooling cyclic performance, which was associated with operational stability in actual electric heating applications.

  6. Highly excited hydrogen in strong d. c. electric fields: atomic engineering

    Energy Technology Data Exchange (ETDEWEB)

    Nayfeh, M.H.


    We excite atomic hydrogen from the ground state via a three-photon process to high-lying excited states in the presence of strong d.c. electric fields. The external field is used to manipulate, control, and design specific atomic structures. We can construct nearly 'one-dimensional' atoms whose electronic distributions are highly extended along the field, and which may have enormous electric dipole moments ('giant-dipole atoms').

  7. Calculation formula for apparent electrical resistivity of high porosity metal materials

    Institute of Scientific and Technical Information of China (English)

    刘培生; 付超; 李铁藩


    A geometrical model has been established based on the structure feature of high porosity metal materials,the mathematical relationship between electrical resistivity and porosity for high porosity materials with even structure has then been deduced conveniently, and the formula for calculating the electrical resistivity of high porosity materials through porosity, which is easy to know, has been acquired further. Besides, the theoretical formula was verified to coincide with the test results well by the application taking nickel foam as an example.

  8. High-performance electrically conductive silver paste prepared by silver-containing precursor

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Jianguo; Cao, Yu; Li, Xiangyou; Wang, Xiaoye; Zeng, Xiaoyan [Huazhong University of Science and Technology, Wuhan National Laboratory for Optoelectronics, College of Optoelectronics Science and Engineering, Wuhan (China)


    A high-performance electrically conductive silver paste with no solid particles before drying and/or sintering is developed, in which silver-containing precursor is employed as conductive functional phase. Thermogravimetry analysis, volume electrical resistivity tests and sintering experiments show that the paste with about 14 wt.% silver pristine content is able to achieve the volume electrical resistivity of (2-3) x 10{sup -5} {omega} cm after it is sintered at 220 C. A micro-pen direct-writing process indicates that it is very suitable for the fabrication of high-resolution (25 {mu}m) and high-integration devices and apparatus. (orig.)

  9. High-performance electrically conductive silver paste prepared by silver-containing precursor (United States)

    Liu, Jianguo; Cao, Yu; Li, Xiangyou; Wang, Xiaoye; Zeng, Xiaoyan


    A high-performance electrically conductive silver paste with no solid particles before drying and/or sintering is developed, in which silver-containing precursor is employed as conductive functional phase. Thermogravimetry analysis, volume electrical resistivity tests and sintering experiments show that the paste with about 14 wt.% silver pristine content is able to achieve the volume electrical resistivity of (2-3) ×10-5 Ω cm after it is sintered at 220°C. A micro-pen direct-writing process indicates that it is very suitable for the fabrication of high-resolution (25 μm) and high-integration devices and apparatus.

  10. Synthesis and high-pressure electrical resistivity studies of Ti{sub 3}Al

    Energy Technology Data Exchange (ETDEWEB)

    Vennila, R. Selva [Department of Physics, Anna University, Chennai 600025 (India)]. E-mail:; Porchelvi, E. Elamurugu [Department of Physics, Anna University, Chennai 600025 (India); Joy, K.M. Freny [Department of Physics, Anna University, Chennai 600025 (India); Arun, T.K. Jaya [Department of Physics, Anna University, Chennai 600025 (India); Jaya, N. Victor [Department of Physics, Anna University, Chennai 600025 (India)


    Titanium aluminide (Ti{sub 3}Al) has been synthesized by a powder metallurgical method. X-ray diffraction studies show the formation of a single phase with hexagonal structure. Electrical resistivity studies were carried out by a four-probe technique both at high pressure and high temperature using a Bridgman Opposed Anvil High Pressure Device (OAHPD). The sample was studied up to a pressure and temperature of 10 GPa and 250 deg. C, respectively. The electrical resistivity is found to decrease with increasing pressure. The temperature effect causes an upward shift in the electrical resistivity in the range of pressure considered.

  11. High output power electric motors with bulk HTS elements (United States)

    Kovalev, L. K.; Ilushin, K. V.; Kovalev, K. L.; Penkin, V. T.; Poltavets, V. N.; Koneev, S. M.-A.; Akimov, I. I.; Gawalek, W.; Oswald, B.; Krabbes, G.


    New types of electric machines with the rotors containing bulk HTS (YBCO and Bi-Ag) elements are presented. Different schematics of hysteresis, reluctance, “trapped field” and composed synchronous HTS machines are discussed. The two-dimensional mathematical models describing the processes in such types of HTS machines were developed on the basis of the theoretical analysis of the electrodynamic and hysteresis processes in the single-domain and polycrystal YBCO ceramic samples and plate shape Bi-Ag elements. The test results of the series of hysteresis, reluctance, “trapped field” and composed with permanent magnets HTS motors with output power rating 0.1-18 kW and current frequency 50 and 400 Hz are given. These results show that in the media of liquid nitrogen the specific output power per one weight unit of HTS motors is 4-7 times better than for conventional electric machines. Comparison of the theoretical and experimental characteristics of the developed HTS motors show that they are in good agreement. The test results for liquid nitrogen cryogenic pump system with hysteresis 500 W HTS motor are discussed. The designs and first test results of HTS motor operating in the media of liquid nitrogen with output power 100 kW and power factor more than 0.8 are given. Future development and applications of new types of HTS motors for aerospace technology, on-land industry and transport systems are discussed.

  12. High impact ionization rate in silicon by sub-picosecond THz electric field pulses (Conference Presentation)

    DEFF Research Database (Denmark)

    Tarekegne, Abebe Tilahun; Iwaszczuk, Krzysztof; Hirori, Hideki


    Summary form only given. Metallic antenna arrays fabricated on high resistivity silicon are used to localize and enhance the incident THz field resulting in high electric field pulses with peak electric field strength reaching several MV/cm on the silicon surface near the antenna tips. In such high...... electric field strengths high density of carriers are generated in silicon through impact ionization process. The high density of generated carriers induces a change of refractive index in silicon. By measuring the change of reflectivity of tightly focused 800 nm light, the local density of free carriers...... near the antenna tips is measured. Using the NIR probing technique, we observed that the density of carriers increases by over 8 orders of magnitude in a time duration of approximately 500 fs with an incident THz pulse of peak electric field strength 700 kV/cm. This shows that a single impact...

  13. High-frequency thermal-electrical cycles for pyroelectric energy conversion

    Energy Technology Data Exchange (ETDEWEB)

    Bhatia, Bikram [Department of Mechanical Science and Engineering, University of Illinois Urbana-Champaign, Urbana, Illinois 61801 (United States); Damodaran, Anoop R. [Department of Materials Science and Engineering and Materials Research Laboratory, University of Illinois Urbana-Champaign, Urbana, Illinois 61801 (United States); Cho, Hanna [Department of Mechanical Engineering, Texas Tech University, Lubbock, Texas 79409 (United States); Martin, Lane W. [Department of Materials Science and Engineering and Materials Research Laboratory, University of Illinois Urbana-Champaign, Urbana, Illinois 61801 (United States); Department of Materials Science and Engineering, University of California, Berkeley, California 94720 (United States); King, William P., E-mail: [Department of Mechanical Science and Engineering, University of Illinois Urbana-Champaign, Urbana, Illinois 61801 (United States); Department of Materials Science and Engineering and Materials Research Laboratory, University of Illinois Urbana-Champaign, Urbana, Illinois 61801 (United States)


    We report thermal to electrical energy conversion from a 150 nm thick BaTiO{sub 3} film using pyroelectric cycles at 1 kHz. A microfabricated platform enables temperature and electric field control with temporal resolution near 1 μs. The rapid electric field changes as high as 11 × 10{sup 5 }kV/cm-s, and temperature change rates as high as 6 × 10{sup 5 }K/s allow exploration of pyroelectric cycles in a previously unexplored operating regime. We investigated the effect of phase difference between electric field and temperature cycles, and electric field and temperature change rates on the electrical energy generated from thermal-electrical cycles based on the pyroelectric Ericsson cycle. Complete thermodynamic cycles are possible up to the highest cycle rates tested here, and the energy density varies significantly with phase shifts between temperature and electric field waveforms. This work could facilitate the design and operation of pyroelectric cycles at high cycle rates, and aid in the design of new pyroelectric systems.

  14. Electric eels use high-voltage to track fast-moving prey. (United States)

    Catania, Kenneth C


    Electric eels (Electrophorus electricus) are legendary for their ability to incapacitate fish, humans, and horses with hundreds of volts of electricity. The function of this output as a weapon has been obvious for centuries but its potential role for electroreception has been overlooked. Here it is shown that electric eels use high-voltage simultaneously as a weapon and for precise and rapid electrolocation of fast-moving prey and conductors. Their speed, accuracy, and high-frequency pulse rate are reminiscent of bats using a 'terminal feeding buzz' to track insects. Eel's exhibit 'sensory conflict' when mechanosensory and electrosensory cues are separated, striking first toward mechanosensory cues and later toward conductors. Strikes initiated in the absence of conductors are aborted. In addition to providing new insights into the evolution of strongly electric fish and showing electric eels to be far more sophisticated than previously described, these findings reveal a trait with markedly dichotomous functions.

  15. SO2 camera measurements at Lastarria volcano and Lascar volcano in Chile (United States)

    Lübcke, Peter; Bobrowski, Nicole; Dinger, Florian; Klein, Angelika; Kuhn, Jonas; Platt, Ulrich


    The SO2 camera is a remote-sensing technique that measures volcanic SO2 emissions via the strong SO2 absorption structures in the UV using scattered solar radiation as a light source. The 2D-imagery (usually recorded with a frame rate of up to 1 Hz) allows new insights into degassing processes of volcanoes. Besides the large advantage of high frequency sampling the spatial resolution allows to investigate SO2 emissions from individual fumaroles and not only the total SO2 emission flux of a volcano, which is often dominated by the volcanic plume. Here we present SO2 camera measurements that were made during the CCVG workshop in Chile in November 2014. Measurements were performed at Lastarria volcano, a 5700 m high stratovolcano and Lascar volcano, a 5600 m high stratovolcano both in northern Chile on 21 - 22 November, 2014 and on 26 - 27 November, 2014, respectively. At both volcanoes measurements were conducted from a distance of roughly 6-7 km under close to ideal conditions (low solar zenith angle, a very dry and cloudless atmosphere and an only slightly condensed plume). However, determination of absolute SO2 emission rates proves challenging as part of the volcanic plume hovered close to the ground. The volcanic plume therefore is in front of the mountain in our camera images. An SO2 camera system consisting of a UV sensitive CCD and two UV band-pass filters (centered at 315 nm and 330 nm) was used. The two band-pass filters are installed in a rotating wheel and images are taken with both filter sequentially. The instrument used a CCD with 1024 x 1024 pixels and an imaging area of 13.3 mm x 13.3 mm. In combination with the focal length of 32 mm this results in a field-of-view of 25° x 25°. The calibration of the instrument was performed with help of a DOAS instrument that is co-aligned with the SO2 camera. We will present images and SO2 emission rates from both volcanoes. At Lastarria gases are emitted from three different fumarole fields and we will attempt

  16. Characteristics of Hawaiian volcanoes (United States)

    Poland, Michael P.; Takahashi, T. Jane; Landowski, Claire M.


    Founded in 1912 at the edge of the caldera of Kīlauea Volcano, HVO was the vision of Thomas A. Jaggar, Jr., a geologist from the Massachusetts Institute of Technology, whose studies of natural disasters around the world had convinced him that systematic, continuous observations of seismic and volcanic activity were needed to better understand—and potentially predict—earthquakes and volcanic eruptions. Jaggar summarized the aim of HVO by stating that “the work should be humanitarian” and have the goals of developing “prediction and methods of protecting life and property on the basis of sound scientific achievement.” These goals align well with those of the USGS, whose mission is to serve the Nation by providing reliable scientific information to describe and understand the Earth; minimize loss of life and property from natural disasters; manage natural resources; and enhance and protect our quality of life.

  17. High output power reluctance electric motors with bulk high-temperature superconductor elements (United States)

    Kovalev, L. K.; Ilushin, K. V.; Penkin, V. T.; Kovalev, K. L.; Larionoff, A. E.; M-A Koneev, S.; Modestov, K. A.; Larionoff, S. A.; Poltavets, V. N.; Akimov, I. I.; Alexandrov, V. V.; Gawalek, W.; Oswald, B.; Krabbes, G.


    We present new types of electric machines with the rotors containing bulk high-temperature superconductor (HTS) - YBCO and Bi-Ag - elements. We discuss different schematics of hysteresis, reluctance, 'trapped field' and composed synchronous HTS machines. The two-dimensional mathematical models describing the processes in such types of HTS machines were developed on the basis of the theoretical analysis of the electrodynamic and hysteresis processes in the single-domain and polycrystal YBCO ceramic samples and plate shape Bi-Ag elements. We give the test results of the series of hysteresis, reluctance, 'trapped field' and composed with permanent magnets HTS motors with an output power rating of 0.1-18 kW and current frequencies 50 Hz and 400 Hz. These results show that in the media of liquid nitrogen the specific output power per one unit weight of the HTS motor is four to seven times better than for conventional electric machines. A comparison of the theoretical and experimental characteristics of the developed HTS motors show that they are in good agreement. We discuss the test results for a liquid nitrogen cryogenic pump system with a hysteresis 500 W HTS motor. We describe several designs of new HTS motors operating in the media of liquid nitrogen with an output power 125 kW (and more) and a power factor of more than 0.8. We discuss future applications of new types of HTS motors for aerospace technology, on-land industry and transport systems.

  18. Nonlinear relaxation field in charged systems under high electric fields

    Energy Technology Data Exchange (ETDEWEB)

    Morawetz, K


    The influence of an external electric field on the current in charged systems is investigated. The results from the classical hierarchy of density matrices are compared with the results from the quantum kinetic theory. The kinetic theory yields a systematic treatment of the nonlinear current beyond linear response. To this end the dynamically screened and field-dependent Lenard-Balescu equation is integrated analytically and the nonlinear relaxation field is calculated. The classical linear response result known as Debye - On-Sager relaxation effect is only obtained if asymmetric screening is assumed. Considering the kinetic equation of one specie the other species have to be screened dynamically while the screening with the same specie itself has to be performed statically. Different other approximations are discussed and compared. (author)

  19. High Sensitive Electrical Metamaterial Sensor for Fuel Adulteration Detection

    Directory of Open Access Journals (Sweden)

    Vaishali Rawat


    Full Text Available Life of any automobile engine is largely dependent on the purity as well as the optimum ratios of their fuels, viz. petrol, diesel and ethanol. A device working on the electrical metamaterial concept, namely a complementary split ring resonator (CSRR, operating at 2.47 GHz (ISM band, is proposed to detect kerosene adulteration in petrol. Kerosene was varied upto 30 per cent with minimum detection limit as low as 10 per cent. Systematic shifts in the transmission resonance frequency were observed. The sensing was fast and the recovery was instantaneous. The underlying concept of interference of electromagnetic radiation through the CSRR circuit and its further manipulation with the changes in the dielectric ambience is elaborated.

  20. Numerical simulation of high voltage electric pulse comminution of phosphate ore

    Institute of Scientific and Technical Information of China (English)

    Razavian Seyed Mohammad; Rezai Bahram; Irannajad Mehdi; Ravanji Mohammad Hasan


    Numerical simulation of the electrical field distribution helps in-depth understanding of the mechanisms behind the responses and the benefits of the high voltage pulse comminution. The COMSOL Multiphysics package was used to numerically simulate the effect of ore compositions in this study. Regarding phos-phate ore particles shape and composition, the effects of mineral composition, particle size, particle shape and electrodes distance were investigated on the electrical field intensity and distribution. The results show that the induced electrical field is significantly dependent on the electrical properties of minerals, the feed particle size and the location of conductive minerals in ores. The angle of material contact sur-face with the discharge electrode is also an important factor in the intensity of electrical field. Moreover, it is found that the specific liberation effect at the disintegration of phosphate ore by electrical pulses is due to the locality of the electrical field at the interface of mineral components of the phosphate ore aggregates with different permittivities. However, the intensity of the electrical field increases with shar-pening the contact angle. Besides, the electrical discharge in the samples is converted to the elec-trohydraulic discharge across the surrounding water by changing the distance between the discharge electrode and sample surface.

  1. Darwin's triggering mechanism of volcano eruptions (United States)

    Galiev, Shamil


    Charles Darwin wrote that ‘… the elevation of many hundred square miles of territory near Concepcion is part of the same phenomenon, with that splashing up, if I may so call it, of volcanic matter through the orifices in the Cordillera at the moment of the shock;…' and ‘…a power, I may remark, which acts in paroxysmal upheavals like that of Concepcion, and in great volcanic eruptions,…'. Darwin reports that ‘…several of the great chimneys in the Cordillera of central Chile commenced a fresh period of activity ….' In particular, Darwin reported on four-simultaneous large eruptions from the following volcanoes: Robinson Crusoe, Minchinmavida, Cerro Yanteles and Peteroa (we cite the Darwin's sentences following his The Voyage of the Beagle and researchspace. auckland. ac. nz/handle/2292/4474). Let us consider these eruptions taking into account the volcano shape and the conduit. Three of the volcanoes (Minchinmavida (2404 m), Cerro Yanteles (2050 m), and Peteroa (3603 m)) are stratovolcanos and are formed of symmetrical cones with steep sides. Robinson Crusoe (922 m) is a shield volcano and is formed of a cone with gently sloping sides. They are not very active. We may surmise, that their vents had a sealing plug (vent fill) in 1835. All these volcanoes are conical. These common features are important for Darwin's triggering model, which is discussed below. The vent fill material, usually, has high level of porosity and a very low tensile strength and can easily be fragmented by tension waves. The action of a severe earthquake on the volcano base may be compared with a nuclear blast explosion of the base. It is known, that after a underground nuclear explosion the vertical motion and the surface fractures in a tope of mountains were observed. The same is related to the propagation of waves in conical elements. After the explosive load of the base. the tip may break and fly off at high velocity. Analogous phenomenon may be generated as a result of a

  2. Electricity demand profile with high penetration of heat pumps in Nordic area

    DEFF Research Database (Denmark)

    Liu, Zhaoxi; Wu, Qiuwei; Nielsen, Arne Hejde


    This paper presents the heat pump (HP) demand profile with high HP penetration in the Nordic area in order to achieve the carbon neutrality power system. The calculation method in the European Standard EN14825 was used to estimate the HP electricity demand profile. The study results show there wi......This paper presents the heat pump (HP) demand profile with high HP penetration in the Nordic area in order to achieve the carbon neutrality power system. The calculation method in the European Standard EN14825 was used to estimate the HP electricity demand profile. The study results show...... there will be high power demand from HPs and the selection of supplemental heating for heat pumps has a big impact on the peak electrical power load of heating. The study in this paper gives an estimate of the scale of the electricity demand with high penetration of heat pumps in the Nordic area....

  3. Integrating High Levels of Variable Renewable Energy into Electric Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Kroposki, Benjamin D. [National Renewable Energy Laboratory (NREL), Golden, CO (United States)


    As more variable renewable energy is integrated into electric power systems, there are a range of challenges and solutions to accommodating very high penetration levels. This presentation highlights some of the recent research in this area.

  4. Analysis of Condition-Based Maintenance for High-Valtage Electric Power

    Institute of Scientific and Technical Information of China (English)

    HAO Jing-sheng


    The development process of high-voltage electric power equipment maintenance was introduced. It is pointed out that the trend of high-voltage electric power equipment maintenance is so called condition-based maintenance. With the development of computer technology and sensors, on-line monitoring of high-voltage electric power equipment has developed rapidly. By introducing the main principle of Schering bridge to measure tanδ, the way of on-line monitoring of high-voltage electric power equipment was explained. Difference methods of on-line monitoring of insulation parameters for 35 kV substation were discussed. Finally, the shortcomings as well as its tendency of on-line monitoring were analyzed.

  5. Evaluation of the impact of the 2010 pyroclastic density currents at Merapi volcano from high-resolution satellite imagery, field investigations and numerical simulations (United States)

    Charbonnier, S. J.; Germa, A.; Connor, C. B.; Gertisser, R.; Preece, K.; Komorowski, J.-C.; Lavigne, F.; Dixon, T.; Connor, L.


    The 2010 pyroclastic density currents (PDC) at Merapi have presented a rare opportunity to collect a uniquely detailed dataset of the source, extent, lateral variations and impact of various PDC deposits on a densely populated area. Using traditional volcanological field-based methods and a multi-temporal dataset of high-resolution satellite imagery, a total of 23 PDC events have been recognized, including 5 main channeled flows, 15 overbank flows derived from overspill and re-channelization of the main PDCs into adjacent tributaries and two main surge events. The 2010 PDC deposits covered an area of ~ 22.3 km2, unequally distributed between valley-filling (6.9%), overbank (22.4%) and surge and associated fallout deposits (71.7%). Their total estimated non-DRE volume is ~ 36.3 × 106 m3, with 50.2% of this volume accounting for valley-filling deposits, 39.3% for overbank deposits and 10.5% for surge and associated fallout deposits. More than 70% of the total volume was deposited during the third eruptive phase (4-5 November), and only 16.6%, 11.5% and 0.9% during the first (26-29 October), second (30 October - 3 November) and fourth phase (6-23 November), respectively. The internal architecture and lithofacies variations of the 2010 PDC deposits were investigated using data collected from 30 stratigraphic sections measured after one rainy season of erosion. The results show that complex, local-scale variations in flow dynamics and deposit architectures are apparent and that the major factors controlling the propagation of the main flows and their potential hazards for overbanking were driven by: (1) the rapid emplacement of several voluminous PDCs, associated with the steady infilling of the receiving landscape after the two first phases of the eruption; (2) longitudinal changes in channel capacity following increased sinuosity in the valley and decreased containment space; and (3) the effects of varying source mechanisms (gravitational dome collapse, vertical or

  6. Volcanoes in Eruption - Set 1 (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The word volcano is used to refer to the opening from which molten rock and gas issue from Earth's interior onto the surface, and also to the cone, hill, or mountain...

  7. Volcanoes in Eruption - Set 2 (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The word volcano is used to refer to the opening from which molten rock and gas issue from Earth's interior onto the surface, and also to the cone, hill, or mountain...

  8. USGS Volcano Notification Service (VNS) (United States)

    U.S. Geological Survey, Department of the Interior — Website provides a subscription service to receive an email when changes occur in the activity levels for monitored U.S. volcanoes and/or when information releases...

  9. High Temperature Electrical Insulation Materials for Space Applications Project (United States)

    National Aeronautics and Space Administration — NASA's future space science missions cannot be realized without the state of the art high temperature insulation materials of which higher working temperature, high...

  10. Nanostructured Cu-Cr alloy with high strength and electrical conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Islamgaliev, R. K., E-mail:; Nesterov, K. M. [Institute of Physics of Advanced Materials, Ufa State Aviation Technical University, Ufa 450000 (Russian Federation); Bourgon, J.; Champion, Y. [ICMPE-CNRS, Université Paris 12, 6-8 rue Henri Dunant, 94320 Thiais, cedex (France); Valiev, R. Z. [Institute of Physics of Advanced Materials, Ufa State Aviation Technical University, Ufa 450000 (Russian Federation); Laboratory for Mechanics of Bulk Nanostructured Materials, Saint Petersburg State University, 198504 Peterhof, Saint Petersburg (Russian Federation)


    The influence of nanostructuring by high pressure torsion (HPT) on strength and electrical conductivity in the Cu-Cr alloy has been investigated. Microstructure of HPT samples was studied by transmission electron microscopy with special attention on precipitation of small chromium particles after various treatments. Effect of dynamic precipitation leading to enhancement of strength and electrical conductivity was observed. It is shown that nanostructuring leads to combination of high ultimate tensile strength of 790–840 MPa, enhanced electrical conductivity of 81%–85% IACS and thermal stability up to 500 °C. The contributions of grain refinement and precipitation to enhanced properties of nanostructured alloy are discussed.

  11. The effect of high voltage, high frequency pulsed electric field on slain ovine cortical bone. (United States)

    Asgarifar, Hajarossadat; Oloyede, Adekunle; Zare, Firuz


    High power, high frequency pulsed electric fields known as pulsed power (PP) has been applied recently in biology and medicine. However, little attention has been paid to investigate the application of pulse power in musculoskeletal system and its possible effect on functional behavior and biomechanical properties of bone tissue. This paper presents the first research investigating whether or not PP can be applied safely on bone tissue as a stimuli and what will be the possible effect of these signals on the characteristics of cortical bone by comparing the mechanical properties of this type of bone pre and post expose to PP and in comparison with the control samples. A positive buck-boost converter was applied to generate adjustable high voltage, high frequency pulses (up to 500 V and 10 kHz). The functional behavior of bone in response to pulse power excitation was elucidated by applying compressive loading until failure. The stiffness, failure stress (strength) and the total fracture energy (bone toughness) were determined as a measure of the main bone characteristics. Furthermore, an ultrasonic technique was applied to determine and comprise bone elasticity before and after pulse power stimulation. The elastic property of cortical bone samples appeared to remain unchanged following exposure to pulse power excitation for all three orthogonal directions obtained from ultrasonic technique and similarly from the compression test. Nevertheless, the compressive strength and toughness of bone samples were increased when they were exposed to 66 h of high power pulsed electromagnetic field compared to the control samples. As the toughness and the strength of the cortical bone tissue are directly associated with the quality and integrity of the collagen matrix whereas its stiffness is primarily related to bone mineral content these overall results may address that although, the pulse power stimulation can influence the arrangement or the quality of the collagen network

  12. Experimental measurement of the electrical conductivity of single crystal olivine at high temperature and high pressure under different oxygen fugacities

    Institute of Scientific and Technical Information of China (English)


    At 1.0-4.0 GPa and 1123-1473 K and under oxygen fugacity-controlled conditions (Ni + NiO, Fe + Fe3O4, Fe +FeO and Mo + MoO2 buffers), a YJ-3000t Model six-anvil solid high-pressure apparatus and a Sarltron-1260 Impedance/Gain-Phase analyzer were employed to conduct an in situ measurement of the electrical conductivity of single crystal olivine. Experimental results showed that: (1) within the range of experimentally selected frequencies (103-106 Hz), the electrical conductivity of the sample is of great dependence on the frequency; (2) with the rise of temperature (T), the electrical conductivity (σ) will increase, and the Arrenhius linear relationship is established between lgσ and 1/T; (3) under the control of oxygen buffer Fe + Fe3O4, with the rise of pressure, the electrical conductivity tends to decrease whereas the activation enthalpy and independent-of-temperature preexponential factor tend to increase,with the activation energy and activation volume of the sample estimated at ( 1.25 ± 0.08) eV and (0. 105 ± 0. 025) cm3/mol, respectively; (4) under given pressure and temperature conditions, the electrical conductivity tends to increase whereas the activation energy tends to decrease with increasing oxygen fugacity; and (5) the mechanism of electrical conduction of small polarons can provide insight into the behavior of electrical conduction of olivine under high pressure and high temperature.

  13. Study on high efficient electric discharge milling of silicon carbide ceramic with high resistivity

    Institute of Scientific and Technical Information of China (English)

    JI RenJie; LIU YongHong; YU LiLi; LI XiaoPeng; DONG Xin


    A new method which employs a group pulse power supply for electric discharge milling of the silicon high pulse utilization, the material removal rate (MRR) can reach 72.9 mm3/min. The effects of high-frequency pulse duration, high-frequency pulse interval, peak voltage, peak current, polarity, ro-tate speed and group frequency on the process performance have been investigated. Also the EDMed surface microstructure is examined with a scanning electron microscope (SEM), an X-ray diffraction (XRD), an energy dispersive spectrometer (EDS) and a micro hardness tester. The results show that the conditions of smaller high-frequency pulse duration and pulse interval, higher peak voltage and peak current, and positive tool polarity are suitable for machining the SiC ceramic. The optimal rotate speed is 1090 r/rain and the preferable group frequency is 730 Hz. In addition, there is a small quantity of iron on machined surface when machining with steel electrode. The average grain size of the EDMed sur-face is smaller than that of the unprocessed, and the micro hardness of machined surface is superior to that of the unprocessed.

  14. Self-Healable Electrical Insulation for High Voltage Applications (United States)

    Williams, Tiffany S.


    Polymeric aircraft electrical insulation normally degrades by partial discharge with increasing voltage, which causes excessive localized Joule heating in the material and ultimately leads to dielectric failure of the insulator through thermal breakdown. Developing self-healing insulation could be a viable option to mitigate permanent mechanical degradation, thus increasing the longevity of the insulation. Instead of relying on catalyst and monomer-filled microcapsules to crack, flow, and cure at the damaged sites described in well-published mechanisms, establishment of ionic crosslinks could allow for multiple healing events to occur with the added benefit of achieving full recovery strength under certain thermal environments. This could be possible if the operating temperature of the insulator is the same as or close to the temperature where ionic crosslinks are formed. Surlyn, a commercial material with ionic crosslinks, was investigated as a candidate self-healing insulator based off prior demonstrations of self-healing behavior. Thin films of varying thicknesses were investigated and the effects of thickness on the dielectric strength were evaluated and compared to representative polymer insulators. The effects of thermal conditioning on the recovery strength and healing were observed as a function of time following dielectric breakdown. Moisture absorption was also studied to determine if moisture absorption rates in Surlyn were lower than that of common polyimides.

  15. Novel high power impulse magnetron sputtering enhanced by an auxiliary electrical field. (United States)

    Li, Chunwei; Tian, Xiubo


    The high power impulse magnetron sputtering (HIPIMS) technique is a novel highly ionized physical vapor deposition method with a high application potential. However, the electron utilization efficiency during sputtering is rather low and the metal particle ionization rate needs to be considerably improved to allow for a large-scale industrial application. Therefore, we enhanced the HIPIMS technique by simultaneously applying an electric field (EF-HIPIMS). The effect of the electric field on the discharge process was studied using a current sensor and an optical emission spectrometer. Furthermore, the spatial distribution of the electric potential and electric field during the EF-HIPIMS process was simulated using the ANSYS software. The results indicate that a higher electron utilization efficiency and a higher particle ionization rate could be achieved. The auxiliary anode obviously changed the distribution of the electric potential and the electric field in the discharge region, which increased the plasma density and enhanced the degree of ionization of the vanadium and argon gas. Vanadium films were deposited to further compare both techniques, and the morphology of the prepared films was investigated by scanning electron microscopy. The films showed a smaller crystal grain size and a denser growth structure when the electric field was applied during the discharge process.

  16. High dislocation density of tin induced by electric current

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Yi-Han; Liang, Chien-Lung; Lin, Kwang-Lung, E-mail: [Department of Material Science and Engineering, National Cheng Kung University, Tainan 70101, Taiwan, R. O. C (China); Wu, Albert T. [Department of Chemical and Material Engineering, National Central University, Jhongli 32001, Taiwan, R. O. C (China)


    A dislocation density of as high as 10{sup 17} /m{sup 2} in a tin strip, as revealed by high resolution transmission electron microscope, was induced by current stressing at 6.5 x 10{sup 3} A/ cm{sup 2}. The dislocations exist in terms of dislocation line, dislocation loop, and dislocation aggregates. Electron Backscattered Diffraction images reflect that the high dislocation density induced the formation of low deflection angle subgrains, high deflection angle Widmanstätten grains, and recrystallization. The recrystallization gave rise to grain refining.

  17. Spectroscopic analysis of high electric field enhanced ionization in laser filaments in air for corona guiding

    Institute of Scientific and Technical Information of China (English)

    Yingxia Wei; Yaoxiang Liu; Tie-Jun Wang; Na Chen; Jingjing Ju; Yonghong Liu; Haiyi Sun; Cheng Wang; Jiansheng Liu; Haihe Lu; See Leang Chin; Ruxin Li


    We report on a systematic experimental study on the fluorescence spectra produced from a femtosecond laser filament in air under a high electric field. The electric field alone was strong enough to create corona discharge(CD). Fluorescence spectra from neutral and ionic air molecules were measured and compared with pure high-voltage CD and pure laser filamentation(FIL). Among them, high electric field assisted laser FIL produced nitrogen fluorescence more efficiently than either pure CD or pure FIL processes. The nonlinear enhancement of fluorescence from the interaction of the laser filament and corona discharging electric field resulted in a more efficient ionization along the laser filament zone, which was confirmed by the spectroscopic measurement of both ionization-induced fluorescence and plasma-scattered 800 nm laser pulses. This is believed to be the key precursor process for filament-guided discharge.

  18. Thermal runaway in polyimide at high electric field probed by infrared thermography (United States)

    Diaham, Sombel; Belijar, Guillaume; Locatelli, Marie-Laure; Lebey, Thierry


    An original way for characterizing dielectrics under high electric field and high temperature based on the coupling between electric current measurements and real-time fast infrared (IR) thermography is demonstrated. Particularly, the Joule heating phenomenon at high field is quantified by 2D-temperature cartography in a polyimide (PI) film set at an initial temperature of 300 °C through IR observations of the polarized electrode. 2D-temperature cartography highlights the temperature increase with increasing the electric field. The thermal runway occurs prior to the dielectric breakdown from an electric field threshold of 140-150 V/μm. This corresponds to a dissipated volume power density between 2 and 5 mW/μm3. Such values report the limit of the electro-thermal equilibrium in PI film.

  19. Study of seismic response and vibration control of High voltage electrical equipment damper based on TMD (United States)

    Liu, Chuncheng; Wang, Chongyang; Mao, Long; Zha, Chuanming


    Substation high voltage electrical equipment such as mutual inductor, circuit interrupter, disconnecting switch, etc., has played a key role in maintaining the normal operation of the power system. When the earthquake disaster, the electrical equipment of the porcelain in the transformer substation is the most easily to damage, causing great economic losses. In this paper, using the method of numerical analysis, the establishment of a typical high voltage electrical equipment of three dimensional finite element model, to study the seismic response of a typical SF6 circuit breaker, at the same time, analysis and contrast the installation ring tuned mass damper (TMD damper for short), by changing the damper damping coefficient and the mass block, install annular TMD vibration control effect is studied. The results of the study for guiding the seismic design of high voltage electrical equipment to provide valuable reference.

  20. Plasma oscillations in two-dimensional semiconductor superstructures in the presence of a high electric field

    CERN Document Server

    Glazov, S Y


    The effect of the high permanent electric field on plasma oscillations in the two-dimensional electron gas with the superstructure and taking into account the transfer processes is investigated. The dispersions omega(k) is obtained for the case of high temperature T (DELTA << T, where DELTA is the width of the conductivity miniband). It is shown that the frequency of plasmons in the high electric field depends on the value of the electric field intensity and the wave number k as the oscillating function. The spectrum is periodic with the period equal to 2 pi/d for arbitrary values of k. The numerical estimation shown that the oscillations can be manifested at the electric field intensity more than 3 x 10 sup 3 V/cm

  1. Electrical activity during the 2006 Mount St. Augustine volcanic eruptions (United States)

    Thomas, Ronald J.; Krehbiel, Paul R.; Rison, William; Edens, H. E.; Aulich, G. D.; McNutt, S.R.; Tytgat, Guy; Clark, E.


    By using a combination of radio frequency time-of-arrival and interferometer measurements, we observed a sequence of lightning and electrical activity during one of Mount St. Augustine's eruptions. The observations indicate that the electrical activity had two modes or phases. First, there was an explosive phase in which the ejecta from the explosion appeared to be highly charged upon exiting the volcano, resulting in numerous apparently disorganized discharges and some simple lightning. The net charge exiting the volcano appears to have been positive. The second phase, which followed the most energetic explosion, produced conventional-type discharges that occurred within plume. Although the plume cloud was undoubtedly charged as a result of the explosion itself, the fact that the lightning onset was delayed and continued after and well downwind of the eruption indicates that in situ charging of some kind was occurring, presumably similar in some respects to that which occurs in normal thunderstorms.

  2. Aromatic Polyurea Possessing High Electrical Energy Density and Low Loss (United States)

    Thakur, Yash; Lin, Minren; Wu, Shan; Zhang, Q. M.


    We report the development of a dielectric polymer, poly (ether methyl ether urea) (PEMEU), which possesses a dielectric constant of 4 and is thermally stable up to 150°C. The experimental results show that the ether units are effective in softening the rigid polymer and making it thermally processable, while the high dipole moment of urea units and glass structure of the polymer leads to a low dielectric loss and low conduction loss. As a result, PEMEU high quality thin films can be fabricated which exhibit exceptionally high breakdown field of >1.5 GV/m, and a low conduction loss at fields up to the breakdown. Consequently, the PEMEU films exhibit a high charge-discharge efficiency of 90% and a high discharged energy density of 36 J/cm3.

  3. Hunting remnants of maar-diatreme-volcanoes (United States)

    Kroner, Corinna; Kämpf, Horst; Matthes, Heidrun; Jahr, Thomas; Markwart, David; Hermann, Tobias; Mrlina, Jan


    In the area of the Rostock-Leipzig-Regensburg fault zone (Germany) several centres of seismic activity are found with seismicity manifesting itself in swarm earthquakes. The occurrence of these earthquakes is globally linked to ascending magma and magmatic fluids. Information is scarce regarding the depth and geometry of the magmatic source, dynamics in the sub-Moho/lower crust region and fluid-tectonic processes in the upper crust in this area. From studies of maar structures located in the seismic active section of the fault zone magma-tectonic phenomena can be reconstructed. For this purpose two relicts of maar volcanoes of different age within a distance of 60 km are investigated by geophysical surveys. Both structures are located in a distance of a few 10 km from recent swarm earthquake centres. The diatreme structure near Ebersbrunn/W-Saxony which is probably of tertiary age is known for several years, the late Quaternary, volcanic palaeo-lake near Mýtina close to the Czech-German border was only recently discovered. Both structures are characterized by distinct gravimetric and magnetic anomalies of about -2 mGal and several 100 nT resp. indicating steeply dipping structures as well as electrical conductivity anomalies. The magnetic total field anomaly of the Ebersbrunn structure has an uncommon rugged appearance. The hypothesis of an origin related to a redistribution of material with high magnetic susceptibility values and saponification of magnetic minerals due to melt water run-off after the last glacial period could not be confirmed. Thus the heterogeneous anomaly character appears to be mainly associated with the degree of weathering of the volcanic material within the diatreme with depth. From 3D gravimetric and magnetic modelling information is gained on geometry and structural composition. Drilling results were used as additional boundary conditions. In both cases modelling reveals an inner zone of significantly reduced density and increased

  4. High Temperature Radiators for Electric Propulsion Systems Project (United States)

    National Aeronautics and Space Administration — The VASIMR propulsion system uses a high temperature Loop Heat Pipe (LHP) radiator to reject heat from the helicon section. The current baseline radiator uses...

  5. The electrical resistance of PuSb under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Link, P. (European Commission, Joint Research Centre, Institute for Transuranium Elements, Postfach 2340, D76125 Karlsruhe (Germany)); Benedict, U. (European Commission, Joint Research Centre, Institute for Transuranium Elements, Postfach 2340, D76125 Karlsruhe (Germany)); Wittig, J. (Institut fuer Festkoerperforschung, Forschungszentrum Juelich, D52425 Juelich (Germany)); Wuehl, H. (Institut fuer Experimentelle Kernphysik, Universitaet Karlsruhe, D76128 Karlsruhe (Germany)); Rebizant, J. (European Commission, Joint Research Centre, Institute for Transuranium Elements, Postfach 2340, D76125 Karlsruhe (Germany)); Spirlet, J.C. (European Commission, Joint Research Centre, Institute for Transuranium Elements, Postfach 2340, D76125 Karlsruhe (Germany))


    A new experimental set-up with a Bridgman-type high pressure cell in a closed containment allows resistance measurements on highly radioactive materials. We present results of high pressure, low temperature studies on PuSb single crystals in the pressure range to 25 GPa and at temperatures between 1.3 K and 300 K. As pressure on PuSb is increased, its Neel temperature and the transition temperature to the ferromagnetic ground state are increased. In the pressure range from 10 to 15 GPa, we observed a strong decrease in the resistance associated with the crystallographic phase transition from the B1 (NaCl) to the B2 (CsCl) structure. The high pressure phase appears to be non-magnetic. ((orig.))

  6. High Concentration of Heat Pumps in Suburban Areas and Reduction of Their Impact on the Electricity Network


    Pruissen, O.P. van; Kamphuis, I.G.


    One of the challenges of the near future for a more renewable Dutch electricity infrastructure is the embedding of high concentrations of heat pumps in currently built domestic residences. In the Dutch situation demand of electricity occurs simultaneously with demand of heat, high electricity peak loads in the low voltage network are expected. This study focuses on domestic residences with high peak loads at substations when heating is provided merely by heat pumps with additional electric re...

  7. High Temperature Superconductors for the Electric Power Grid (United States)

    Malozemoff, Alexis P.


    High Temperature Superconductor power equipment is positioned to play a key role in addressing our national and global energy challenges. While the most obvious benefit is efficiency by using the superconductor's lossless current flow to cut the 10% power lost in the grid, other benefits are likely to be even more impactful. These benefits arise from the high current density of superconductor wire which enables design of highly power-dense and compact equipment including high capacity cables and rotating machinery -- generators and motors. Vast and dense urban areas are becoming home to an increasingly large proportion of world population, and high capacity ac superconductor cables offer a non-interfering and easily installed solution to increasing urban power needs. Longer term, the ultra-low loss of long-distance dc superconductor cables offers strengthened links and power sharing across wide geographical areas. Compact superconductor generators are the key to high power off-shore wind turbines, a major source of renewable energy. Some of these applications have reached a sophisticated level of demonstration, initiating commercial use.

  8. Modeling transcranial electric stimulation in mouse: a high resolution finite element study. (United States)

    Bernabei, John M; Lee, Won Hee; Peterchev, Angel V


    Mouse models are widely used in studies of various forms of transcranial electric stimulation (TES). However, there is limited knowledge of the electric field distribution induced by TES in mice, and computational models to estimate this distribution are lacking. This study examines the electric field and current density distribution in the mouse brain induced by TES. We created a high-resolution finite element mouse model incorporating ear clip electrodes commonly used in mouse TES to study, for example, electroconvulsive therapy (ECT). The electric field strength and current density induced by an ear clip electrode configuration were computed in the anatomically realistic, inhomogenous mouse model. The results show that the median electric field strength induced in the brain at 1 mA of stimulus current is 5.57 V/m, and the strongest field of 20.19 V/m was observed in the cerebellum. Therefore, to match the median electric field in human ECT at 800 mA current, the electrode current in mouse should be set to approximately 15 mA. However, the location of the strongest electric field in posterior brain regions in the mouse does not model well human ECT which targets more frontal regions. Therefore, the ear clip electrode configuration may not be a good model of human ECT. Using high-resolution realistic models for simulating TES in mice may guide the establishment of appropriate stimulation parameters for future in vivo studies.

  9. A Novel Dual-Electrode Plug to Achieve Intensive Electric Field for High Performance Ignition

    Directory of Open Access Journals (Sweden)

    Chih-Lung Shen


    Full Text Available A thorough analysis of electric field is carried out so as to verify that a novel dual-electrode plug can build intensive electric field and can improve the main drawbacks of feeble electric field and low ignition efficiency of the traditional plug. With intensive electric field, the proposed novel plug can achieve high performance ignition, resulting in fuel saving and exhaust reduction. Gauss law is applied for electric field analysis to show that intensive electric field can be built by the novel plug. Then, according to Faraday law a lower-voltage ignition feature accomplished by the plug is discussed. Compared with traditional plug, the novel dual-electrode plug has the following advantages. (1 Much higher energy density is built between the plug electrodes, lowering ignition voltage requirement. (2 Electromagnetic interference (EMI problem caused by high ignition voltage is readily resolved. (3 Ignition time delay can be improved. (4 The feature to save fuel consuming is achieved. (5 The exhaust of CO and HC is reduced significantly. Practical measurements are fulfilled to validate the electric field analysis and to demonstrate the features of the proposed dual-electrode plug.

  10. "Mediterranean volcanoes vs. chain volcanoes in the Carpathians" (United States)

    Chivarean, Radu


    Volcanoes have always represent an attractive subject for students. Europe has a small number of volcanoes and Romania has none active ones. The curricula is poor in the study of volcanoes. We want to make a parallel between the Mediterranean active volcanoes and the old extinct ones in the Oriental Carpathians. We made an comparison of the two regions in what concerns their genesis, space and time distribution, the specific relief and the impact in the landscape, consequences of their activities, etc… The most of the Mediterranean volcanoes are in Italy, in the peninsula in Napoli's area - Vezuviu, Campi Flegrei, Puzzoli, volcanic islands in Tirenian Sea - Ischia, Aeolian Islands, Sicily - Etna and Pantelleria Island. Santorini is located in Aegean Sea - Greece. Between Sicily and Tunisia there are 13 underwater volcanoes. The island called Vulcano, it has an active volcano, and it is the origin of the word. Every volcano in the world is named after this island, just north of Sicily. Vulcano is the southernmost of the 7 main Aeolian Islands, all volcanic in origin, which together form a small island arc. The cause of the volcanoes appears to be a combination of an old subduction event and tectonic fault lines. They can be considered as the origin of the science of volcanology. The volcanism of the Carpathian region is part of the extensive volcanic activity in the Mediterranean and surrounding regions. The Carpathian Neogene/Quaternary volcanic arc is naturally subdivided into six geographically distinct segments: Oas, Gutai, Tibles, Calimani, Gurghiu and Harghita. It is located roughly between the Carpathian thrust-and-fold arc to the east and the Transylvanian Basin to the west. It formed as a result of the convergence between two plate fragments, the Transylvanian micro-plate and the Eurasian plate. Volcanic edifices are typical medium-sized andesitic composite volcanoes, some of them attaining the caldera stage, complicated by submittal or peripheral domes

  11. Hydrothermal reservoir beneath Taal Volcano (Philippines): Implications to volcanic activity (United States)

    Nagao, T.; Alanis, P. B.; Yamaya, Y.; Takeuchi, A.; Bornas, M. V.; Cordon, J. M.; Puertollano, J.; Clarito, C. J.; Hashimoto, T.; Mogi, T.; Sasai, Y.


    Taal Volcano is one of the most active volcanoes in the Philippines. The first recorded eruption was in 1573. Since then it has erupted 33 times resulting in thousands of casualties and large damages to property. In 1995, it was declared as one of the 15 Decade Volcanoes. Beginning in the early 1990s it has experienced several phases of abnormal activity, including seismic swarms, episodes of ground deformation, ground fissuring and hydrothermal activities, which continues up to the present. However, it has been noted that past historical eruptions of Taal Volcano may be divided into 2 distinct cycles, depending on the location of the eruption center, either at Main Crater or at the flanks. Between 1572-1645, eruptions occurred at the Main Crater, in 1707 to 1731, they occurred at the flanks. In 1749, eruptions moved back to the Main Crater until 1911. During the 1965 and until the end of the 1977 eruptions, eruptive activity once again shifted to the flanks. As part of the PHIVOLCS-JICA-SATREPS Project magnetotelluric and audio-magnetotelluric surveys were conducted on Volcano Island in March 2011 and March 2012. Two-dimensional (2-D) inversion and 3-D forward modeling reveals a prominent and large zone of relatively high resistivity between 1 to 4 kilometers beneath the volcano almost directly beneath the Main Crater, surrounded by zones of relatively low resistivity. This anomalous zone of high resistivity is hypothesized to be a large hydrothermal reservoir filled with volcanic fluids. The presence of this large hydrothermal reservoir could be related to past activities of Taal Volcano. In particular we believe that the catastrophic explosion described during the 1911 eruption was the result of the hydrothermal reservoir collapsing. During the cycle of Main Crater eruptions, this hydrothermal reservoir is depleted, while during a cycle of flank eruptions this reservoir is replenished with hydrothermal fluids.

  12. In-channel electrochemical detection in the middle of microchannel under high electric field. (United States)

    Kang, Chung Mu; Joo, Segyeong; Bae, Je Hyun; Kim, Yang-Rae; Kim, Yongseong; Chung, Taek Dong


    We propose a new method for performing in-channel electrochemical detection under a high electric field using a polyelectrolytic gel salt bridge (PGSB) integrated in the middle of the electrophoretic separation channel. The finely tuned placement of a gold working electrode and the PGSB on an equipotential surface in the microchannel provided highly sensitive electrochemical detection without any deterioration in the separation efficiency or interference of the applied electric field. To assess the working principle, the open circuit potentials between gold working electrodes and the reference electrode at varying distances were measured in the microchannel under electrophoretic fields using an electrically isolated potentiostat. In addition, "in-channel" cyclic voltammetry confirmed the feasibility of electrochemical detection under various strengths of electric fields (∼400 V/cm). Effective separation on a microchip equipped with a PGSB under high electric fields was demonstrated for the electrochemical detection of biological compounds such as dopamine and catechol. The proposed "in-channel" electrochemical detection under a high electric field enables wider electrochemical detection applications in microchip electrophoresis.

  13. Analysis of electric field control methods for foil coils in high-voltage linear actuators

    Directory of Open Access Journals (Sweden)

    Beek T.A. van


    Full Text Available This paper describes multiple electric field control methods for foil coils in high-voltage coreless linear actuators and their sensitivity to misalignment. The investigated field control methods consist of resistive, refractive, capacitive and geometrical solutions for mitigating electric stress at edges and corners of foil coils. These field control methods are evaluated using 2-D boundary element and finite element methods. A comparison is presented between the field control methods and their ability to mitigate electric stress in coreless linear actuators. Furthermore, the sensitivity to misalignment of the field control methods is investigated.

  14. Circulation in the high-latitude thermosphere due to electric fields and Joule heating (United States)

    Heaps, M. G.; Megill, L. R.


    Electric fields in the earth's upper atmosphere are capable of setting the neutral atmosphere in motion via ion-neutral collisions as well as pressure gradients from resultant Joule heating. By means of simple models for the high-latitude thermosphere and electric fields a simplified set of coupled equations is solved which show that moderate electric fields, when present for a period of several hours, are capable of displacing the neutral atmosphere of the order of 50 km in the vertical, a few hundred kilometers in the north-south direction and over 1000 km in the east-west direction.

  15. CT findings of the brain damages resulting from the high voltage electric injuries

    Energy Technology Data Exchange (ETDEWEB)

    Kim, So Eun; Kim, Young Keun; Shim, Hyang Yi; Lee, Shin Hyung; Lee, Chang Joon [National Medical Center, Seoul (Korea, Republic of)


    The purpose of this study is to evaluate the CT features and pathogenesis of the electric brain injuries. We reviewed the CT scans of 3 patients injured by high-voltage electricity. We evaluated the findings early and delayed periods in each patients. The early CT findings were diffuse brain edema, scalp swelling, and focal hemorrhagic contusion. The findings of delayed period were cerebral infarction, pneumocephalus, brain abscess, and pneumatocele. CT was useful to correlate the pathogenesis and variable features of electric brain injuries.

  16. High Penetrated Wind Farm Impacts on the Electricity Price: The Danish Case

    DEFF Research Database (Denmark)

    Haji Bashi, Mazaher; Yousefi, G. R.; Bak, Claus Leth;


    fossil fuel free overview in Danish energy policies, and the currently great share of wind power (more than 100% for some hours) in supplying the load, it is an interesting benchmark for the future electricity markets. Negative prices, price spikes, and price volatility are considered as the main effects......Energy trading policies, intermittency of wind farm output power, low marginal cost of the production, are the key factors that cause the wind farms to be effective on the electricity price. In this paper, the Danish electricity market is studied as a part of Nord Pool. Considering the completely...... of the high penetrated wind farm integration into electricity markets. Then, stochastic programming approach is employed to compare the volume of trades for a typical wind farm in a high and low wind penetrated market. Although increasing price spikes and volatility was reported in the literature...

  17. Electrical Conductivity of Synthetic Quartz Crystals at High Temperature and Pressure from Complex Impedance Measurements

    Institute of Scientific and Technical Information of China (English)

    王多君; 李和平; 刘丛强; 易丽; 丁东业; 苏根利; 张卫刚


    An electrical conductivity measurement system under high-pressure conditions with a multi-anvil high-pressure apparatus by an ac complex impedance method was set up. With this system, we have successfully measured the electrical conductivity of synthetic quartz under pressure up to approximately 1.0 GPa in the temperature range 661-987K. The values of electrical conductivity decrease with the increasing pressure and increase with the increasing temperature. The activation enthalpies for the α-quartz crystals are 1.10-1.28eV. The electrical conductivity of α-quartz is ionic, with Na ions moving in channels parallel to the c-axis being the predominant current carrier.

  18. Application of high-resolution domestic electricity load profiles in network modelling

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Mendaza, Iker Diaz de Cerio; Heiselberg, Per Kvols


    % of buildings, the loading of the transformer and power lines is reduced in the summer time to 58% and 51%, respectively. However, the power lines are stress with bi-directional power flow. The results indicate that the business-as-usual approach to network modeling is not sufficient to capture......The ongoing development towards electrification of the energy consumption together with large deployment of renewable energy sources creates new challenges of variability and fluctuation of the electricity supply and increases complexity of the network operation. In order to capture all...... the particularities of electricity demand and on-site generation, e.g. the short-term spikes due use of high electricity consumption appliances such like electric kettle, and get a full picture of network performance, a high-resolution input data are needed. This paper compares the business-as-usual network modeling...

  19. Highly electrically conductive nanocomposites based on polymer-infused graphene sponges. (United States)

    Li, Yuanqing; Samad, Yarjan Abdul; Polychronopoulou, Kyriaki; Alhassan, Saeed M; Liao, Kin


    Conductive polymer composites require a three-dimensional 3D network to impart electrical conductivity. A general method that is applicable to most polymers for achieving a desirable graphene 3D network is still a challenge. We have developed a facile technique to fabricate highly electrical conductive composite using vacuum-assisted infusion of epoxy into graphene sponge GS scaffold. Macroscopic GSs were synthesized from graphene oxide solution by a hydrothermal method combined with freeze drying. The GS/epoxy composites prepared display consistent isotropic electrical conductivity around 1 S/m, and it is found to be close to that of the pristine GS. Compared with neat epoxy, GS/epoxy has a 12-orders-of-magnitude increase in electrical conductivity, attributed to the compactly interconnected graphene network constructed in the polymer matrix. This method can be extended to other materials to fabricate highly conductive composites for practical applications such as electronic devices, sensors, actuators, and electromagnetic shielding.

  20. Impact of Electric Fields on Highly Excited Rovibrational States of Polar Dimers

    CERN Document Server

    Gonzalez-Ferez, Rosario


    We study the effect of a strong static homogeneous electric field on the highly excited rovibrational levels of the LiCs dimer in its electronic ground state. Our full rovibrational investigation of the system includes the interaction with the field due to the permanent electric dipole moment and the polarizability of the molecule. We explore the evolution of the states next to the dissociation threshold as the field strength is increased. The rotational and vibrational dynamics are influenced by the field; effects such as orientation, angular motion hybridization and squeezing of the vibrational motion are demonstrated and analyzed. The field also induces avoided crossings causing a strong mixing of the electrically dressed rovibrational states. Importantly, we show how some of these highly excited levels can be shifted to the continuum as the field strength is increased, and reversely how two atoms in the continuum can be brought into a bound state by lowering the electric field strength.

  1. High speed electrical transmission line design and characterization (United States)

    Bates, R.; Buttar, C.; Buytaert, J.; Eklund, L.; de Acedo, L. F. S.; Longstaff, I.; Naik, S.; Sullivan, S.; Wraight, K.


    High Energy Physics (HEP) experiments have unique requirements for data communication. High data speeds, combined with extreme restrictions on materials allowed, leads to custom transmission lines. This paper will present transmission line design theory, simulation and testing methods. Transmission line designs options like flexes and rigid PCBs as well as cables will be studied. Finite Element Analysis (FEA) software packages simulate energy dissipation and quality of transmitted signals. The characterisation techniques of time-domain reflectometry and frequency-domain measurements are discussed and compared. Bit-error-rate testing is presented and its limitations for design discussed. Methods to improve quality, like three different types of equalization are described.

  2. Electrical conductivity of molten CdCl{sub 2} at temperatures as high as 1474 K

    Energy Technology Data Exchange (ETDEWEB)

    Salyulev, Alexander B.; Potapov, Alexei M. [Russian Academy of Sciences, Ekaterinburg (Russian Federation). Inst. of High-Temperature Electrochemistry


    The electrical conductivity of molten CdCl{sub 2} was measured across a wide temperature range (ΔT=628 K), from 846 K to as high as 1474 K, i.e. 241 above the normal boiling point of the salt. In previous studies, a maximum temperature of 1201 K was reached, this being 273 lower than in the present work. The activation energy of electrical conductivity was calculated.

  3. High-voltage electrical burns due to copper theft - Case series. (United States)

    Braga, M J; Oliveira, I; Egipto, P; Silva, A


    Electrical burns are among the most devastating trauma inflicted on the human body. These burns have a higher morbidity, length of stay and a much higher risk of amputation than any other type of burn. Electrical burns affect mostly young, working males because they are more frequently the result of a work accident. However, possibly due to the worldwide economic crisis, we are experiencing a new phenomenon: the theft of high-voltage copper wiring.

  4. High-voltage electrical burns due to copper theft – Case series (United States)

    Braga, M.J.; Oliveira, I.; Egipto, P.; Silva, A.


    Summary Electrical burns are among the most devastating trauma inflicted on the human body. These burns have a higher morbidity, length of stay and a much higher risk of amputation than any other type of burn. Electrical burns affect mostly young, working males because they are more frequently the result of a work accident. However, possibly due to the worldwide economic crisis, we are experiencing a new phenomenon: the theft of high-voltage copper wiring. PMID:27857650

  5. A Witricity-Based High-Power Device for Wireless Charging of Electric Vehicles


    Zhongyu Dai; Junhua Wang; Mengjiao Long; Hong Huang


    In this paper, a Witricity-based high-power device is proposed for wireless charging of electric vehicles. According to the specific requirements of three-stage charging for electric vehicles, four compensation modes of the Witricity system are analyzed by the Loosely Coupled Theory among transformer coils and the Substitution Theorem in circuit theory. In addition, when combining voltage withstand levels, the current withstand capability, the switching frequency of electronic switching tubes...

  6. High efficiency thermal to electric energy conversion using selective emitters and spectrally tuned solar cells (United States)

    Chubb, Donald L.; Flood, Dennis J.; Lowe, Roland A.


    Thermophotovoltaic (TPV) systems are attractive possibilities for direct thermal-to-electric energy conversion, but have typically required the use of black body radiators operating at high temperatures. Recent advances in both the understanding and performance of solid rare-earth oxide selective emitters make possible the use of TPV at temperatures as low as 1500 K. Depending on the nature of parasitic losses, overall thermal-to-electric conversion efficiencies greater than 20 percent are feasible.

  7. High-field electrical and thermal transport in suspended graphene. (United States)

    Dorgan, Vincent E; Behnam, Ashkan; Conley, Hiram J; Bolotin, Kirill I; Pop, Eric


    We study the intrinsic transport properties of suspended graphene devices at high fields (≥1 V/μm) and high temperatures (≥1000 K). Across 15 samples, we find peak (average) saturation velocity of 3.6 × 10(7) cm/s (1.7 × 10(7) cm/s) and peak (average) thermal conductivity of 530 W m(-1) K(-1) (310 W m(-1) K(-1)) at 1000 K. The saturation velocity is 2-4 times and the thermal conductivity 10-17 times greater than in silicon at such elevated temperatures. However, the thermal conductivity shows a steeper decrease at high temperature than in graphite, consistent with stronger effects of second-order three-phonon scattering. Our analysis of sample-to-sample variation suggests the behavior of "cleaner" devices most closely approaches the intrinsic high-field properties of graphene. This study reveals key features of charge and heat flow in graphene up to device breakdown at ~2230 K in vacuum, highlighting remaining unknowns under extreme operating conditions.

  8. High Concentration of Heat Pumps in Suburban Areas and Reduction of Their Impact on the Electricity Network

    NARCIS (Netherlands)

    Pruissen, O.P. van; Kamphuis, I.G.


    One of the challenges of the near future for a more renewable Dutch electricity infrastructure is the embedding of high concentrations of heat pumps in currently built domestic residences. In the Dutch situation demand of electricity occurs simultaneously with demand of heat, high electricity peak l

  9. High Concentration of Heat Pumps in Suburban Areas and Reduction of Their Impact on the Electricity Network

    NARCIS (Netherlands)

    Pruissen, O.P. van; Kamphuis, I.G.


    One of the challenges of the near future for a more renewable Dutch electricity infrastructure is the embedding of high concentrations of heat pumps in currently built domestic residences. In the Dutch situation demand of electricity occurs simultaneously with demand of heat, high electricity peak

  10. Electrical properties of deuteron irradiated high resistivity silicon

    Energy Technology Data Exchange (ETDEWEB)

    Krupka, Jerzy, E-mail: [Insitute of Microelectronics and Optoelectronics, Warsaw University of Technology, Koszykowa 75, 00-662 Warsaw (Poland); Karcz, Waldemar [H. Niewodniczański Institute of Nuclear Physics Polish Academy of Science, Cracow (Poland); Joint Institute for Nuclear Research, Joliot-Curie 6, 141980 Dubna (Russian Federation); Avdeyev, Sergej P. [Joint Institute for Nuclear Research, Joliot-Curie 6, 141980 Dubna (Russian Federation); Kamiński, Paweł; Kozłowski, Roman [Institute of Electronic Materials Technology, Wólczyńska 133, 01-919 Warsaw (Poland)


    We have investigated resistivity changes introduced on the high-resistivity p-type silicon wafer by the irradiation with deuteron beam with an energy of 4.4 GeV performed in the NUCLOTRON superconducting accelerator. Two contactless techniques were used for the measurements of resistivity changes: namely the microwave split post dielectric resonator (SPDR) technique and capacitance measurements in the frequency domain. The first technique allows resistivity measurements in the plane of the wafer, while the second one in the direction perpendicular to the wafer. The resistivity map obtained with the SPDR technique enabled us to obtain a permanent fingerprint of the accelerator beam intensity profile. It has been shown that after the irradiation, the material resistivity increased to ∼3.9 × 10{sup 5} Ω cm in the wafer region exposed to the maximum beam intensity. Complementary studies of the properties and concentrations of radiation deep-level defects were performed by the high-resolution photo-induced current transient spectroscopy (HRPITS). These studies have shown that the irradiation of the high resistivity silicon with 4.4-GeV deuterons results in the formation of several types of deep-level defects responsible for the charge compensation.

  11. The volcano in a gravel pit: Volcano monitoring meets experimental volcanology (United States)

    Kueppers, U.; Alatorre-Ibargüengoitia, M. A.; Hort, M.; Kremers, S.; Meier, K.; Scarlato, P. G.; Scheu, B.; Taddeucci, J.; Wagner, R.; Walk, F.; Dingwell, D. B.


    Volcanic eruptions are an inevitable natural threat. During explosive eruptions, gas and pyroclasts are ejected at high speed over variable time spans and at variable intensity. As magma fragmentation inside a volcanic edifice defies direct observation, our mechanistic and quantitative understanding of the syn-eruptive processes is still incomplete. In an attempt to bridge this gap, we used a supra-disciplinary approach and combined experimental volcanology and volcano monitoring devices. We performed 34 field-based fragmentation experiments using cylindrical samples, drilled from natural volcanic rock samples. Decompression and particle ejection were monitored with (1) Doppler Radar (DR), (2) high-speed and high-definition cameras, (3) high-speed thermal camera, (4) acoustic and infrasound sensors and (5) pressure transducers. The experiments were performed at controlled sample porosity (25 to 75 vol.%) and size (60 mm height and 25 mm and 60 mm diameter, respectively), confinement geometry, applied pressure (4 to 18 MPa) and temperature (25 and 850 °C). We present how the velocity of the ejected pyroclasts was measured by and evaluated for the different approaches and how it was affected by the experimental conditions and sample characteristics. We show that all deployed instruments successfully measured the pyroclast ejection, giving coherent results of up to 130 m/s. Close and high-resolution volcano monitoring, spiced with results from our experiments, will allow for "calibrating volcanoes". An enhanced understanding of the pressurisation state of a volcano is an essential factor in ballistic hazard evaluation and eruption energy estimation and will contribute to adequate risk mitigation.

  12. Dossier high-efficient electric water heater. Electricity by a Stirling engine; Het Dossier HRE-ketel. Stroom uit Stirlingmotor

    Energy Technology Data Exchange (ETDEWEB)

    Scholtens, B.


    The market seems ready for a private power plant on the wall in the attic, which also heats the house. Such an installation is the successor of the high efficiency boiler, which is in use in most of the homes in the Netherlands. After fifteen years of development Dutch companies have taken the lead in this technology. The manufacturer Remeha in Apeldoorn, Netherlands, started one month ago with the production of high efficiency electric boiler. [Dutch] De markt lijkt klaar voor een eigen stroomcentrale aan de muur op zolder die bovendien het huis verwarmt. De installatie is de opvolger van de hoogrendementsketel, die de meeste huizen in Nederland verwarmt. Na vijftien jaar ontwikkeling hebben Nederlandse bedrijven het technologische voortouw genomen. De Apeldoornse fabrikant Remeha is een maand geleden als eerste met serieproductie van de hre-ketel begonnen.

  13. Incorporating Charging/Discharging Strategy of Electric Vehicles into Security-Constrained Optimal Power Flow to Support High Renewable Penetration

    National Research Council Canada - National Science Library

    Kyungsung An; Kyung-Bin Song; Kyeon Hur


    This research aims to improve the operational efficiency and security of electric power systems at high renewable penetration by exploiting the envisioned controllability or flexibility of electric vehicles (EVs...

  14. Semicrystalline Structure-Dielectric Property Relationship and Electrical Conduction in a Biaxially Oriented Poly(vinylidene fluoride) Film under High Electric Fields and High Temperatures. (United States)

    Yang, Lianyun; Ho, Janet; Allahyarov, Elshad; Mu, Richard; Zhu, Lei


    Poly(vinylidene fluoride) (PVDF)-based homopolymers and copolymers are attractive for a broad range of electroactive applications because of their high dielectric constants. Especially, biaxially oriented PVDF (BOPVDF) films exhibit a DC breakdown strength as high as that for biaxially oriented polypropylene films. In this work, we revealed the molecular origin of the high dielectric constant via study of a commercial BOPVDF film. By determination of the dielectric constant for the amorphous phase in BOPVDF, a high value of ca. 21-22 at 25 °C was obtained, and a three-phase (i.e., lamellar crystal/oriented interphase/amorphous region) semicrystalline model was proposed to explain this result. Meanwhile, electronic conduction mechanisms in BOPVDF under high electric fields and elevated temperatures were investigated by thermally stimulated depolarization current (TSDC) spectroscopy and leakage current studies. Space charge injection from metal electrodes was identified as a major factor for electronic conduction when BOPVDF was poled above 75 °C and 20 MV/m. In addition, when silver or aluminum were used as electrodes, new ions were generated from electrochemical reactions under high fields. Due to the electrochemical reactions between PVDF and the metal electrode, a question is raised for practical electrical applications using PVDF and its copolymers under high-field and high-temperature conditions. A potential method to prevent electrochemical degradation of PVDF is proposed in this study.

  15. High frequency vibration characteristics of electric wheel system under in-wheel motor torque ripple (United States)

    Mao, Yu; Zuo, Shuguang; Wu, Xudong; Duan, Xianglei


    With the introduction of in-wheel motor, the electric wheel system encounters new vibration problems brought by motor torque ripple excitation. In order to analyze new vibration characteristics of electric wheel system, torque ripple of in-wheel motor based on motor module and vector control system is primarily analyzed, and frequency/order features of the torque ripple are discussed. Then quarter vehicle-electric wheel system (QV-EWS) dynamics model based on the rigid ring tire assumption is established and the main parameters of the model are identified according to tire free modal test. Modal characteristics of the model are further analyzed. The analysis indicates that torque excitation of in-wheel motor is prone to arouse horizontal vibration, in which in-phase rotational, anti-phase rotational and horizontal translational modes of electric wheel system mainly participate. Based on the model, vibration responses of the QV-EWS under torque ripple are simulated. The results show that unlike vertical low frequency (lower than 20 Hz) vibration excited by road roughness, broadband torque ripple will arouse horizontal high frequency (50-100 Hz) vibration of electric wheel system due to participation of the three aforementioned modes. To verify the theoretical analysis, the bench experiment of electric wheel system is conducted and vibration responses are acquired. The experiment demonstrates the high frequency vibration phenomenon of electric wheel system and the measured order features as well as main resonant frequencies agree with simulation results. Through theoretical modeling, analysis and experiments this paper reveals and explains the high frequency vibration characteristics of electric wheel system, providing references for the dynamic analysis, optimal design of QV-EWS.

  16. High-Voltage Solid Polymer Batteries for Electric Drive Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Eitouni, Hany; Yang, Jin; Pratt, Russell; Wang, Xiao; Grape, Ulrik


    The purpose of this project was for Seeo to develop a high energy lithium based technology with targets of over 500 Wh/l and 325 Wh/kg. Seeo would leverage the work already achieved with its unique proprietary solid polymer DryLyteTM technology in cells which had a specific energy density of 220 Wh/kg. The development work was focused on establishing a dual electrolyte system, coated cathode particle techniques, various types of additives, and different conductive salts. The program had a duration of three years, with Seeo delivering the final cells at the end of 2014 for evaluation by a DOE laboratory.

  17. Heat pumps; Synergy of high efficiency and low carbon electricity

    Energy Technology Data Exchange (ETDEWEB)

    Koike, Akio


    Heat pump is attracting wide attention for its high efficiency to utilize inexhaustible and renewable ambient heat in the environment. With its rapid innovation and efficiency improvement, this technology has a huge potential to reduce CO2 emissions by replacing currently widespread fossil fuel combustion systems to meet various heat demands from the residential, commercial and industrial sectors. Barriers to deployment such as low public awareness and a relatively long pay-back period do exist, so it is strongly recommended that each country implement policies to promote heat pumps as a renewable energy option and an effective method to combat global warming.

  18. Optimal Operation of Plug-In Electric Vehicles in Power Systems with High Wind Power Penetrations

    DEFF Research Database (Denmark)

    Hu, Weihao; Su, Chi; Chen, Zhe


    The Danish power system has a large penetration of wind power. The wind fluctuation causes a high variation in the power generation, which must be balanced by other sources. The battery storage based Plug-In Electric Vehicles (PEV) may be a possible solution to balance the wind power variations...... in the power systems with high wind power penetrations. In this paper, the integration of plug-in electric vehicles in the power systems with high wind power penetrations is proposed and discussed. Optimal operation strategies of PEV in the spot market are proposed in order to decrease the energy cost for PEV...

  19. Experimental Study on the Electrical Conductivity of Pyroxene Andesite at High Temperature and High Pressure (United States)

    Hui, KeShi; Dai, LiDong; Li, HePing; Hu, HaiYing; Jiang, JianJun; Sun, WenQing; Zhang, Hui


    The electrical conductivity of pyroxene andesite was in situ measured under conditions of 1.0-2.0 GPa and 673-1073 K using a YJ-3000t multi-anvil press and Solartron-1260 Impedance/Gain-phase analyzer. Experimental results indicate that the electrical conductivities of pyroxene andesite increase with increasing temperature, and the electrical conductivities decrease with the rise of pressure, and the relationship between electrical conductivity (σ) and temperature (T) conforms to an Arrhenius relation within a given pressure and temperature range. When temperature rises up to 873-923 K, the electrical conductivities of pyroxene andesite abruptly increase, and the activation enthalpy increases at this range, which demonstrates that pyroxene andesite starts to dehydrate. By the virtue of the activation enthalpy (0.35-0.42 eV) and the activation volume (-6.75 ± 1.67 cm3/mole) which characterizes the electrical properties of sample after dehydration, we consider that the conduction mechanism is the small polaron conduction before and after dehydration, and that the rise of carrier concentration is the most important reason of increased electrical conductivity.

  20. Analysis of Distribution of Volcanoes around the Korean Peninsula and the Potential Effects on Korea (United States)

    Choi, Eun-kyeong; Kim, Sung-wook


    Since the scale and disaster characteristics of volcanic eruptions are determined by their geological features, it is important not only to grasp the current states of the volcanoes in neighboring countries around the Korean Peninsula, but also to analyze the tectonic settings, tectonic regions, geological features, volcanic types, and eruption histories of these volcanoes. Volcanic data were based on the volcano information registered with the Global Volcanism Program at the Smithsonian Institute. We created a database of 289 volcanoes around Korea, Japan, China, Taiwan, and the Kamchatka area in Russia, and then identified a high-risk group of 29 volcanoes that are highly likely to affect the region, based on conditions such as volcanic activity, types of rock at risk of eruption, distance from Seoul, and volcanoes having Plinian eruption history with volcanic explosivity index (VEI) of 4 or more. We selected 29 hazardous volcanoes, including Baekdusan, Ulleungdo, and 27 Japanese volcanoes that can cause widespread ashfall on the Korean peninsula by potentially explosive eruptions. In addition, we identified ten volcanoes that should be given the highest priority, through an analysis of data available in literature, such as volcanic ash dispersion results from previous Japanese eruptions, the definition of a large-scale volcano used by Japan's Cabinet Office, and examination of cumulative magma layer volumes from Japan's quaternary volcanoes. We expect that predicting the extent of the spread of ash caused by this hazardous activity and analyzing its impact on the Korean peninsula will be help to predict volcanic ash damage as well as provide direction for hazard mitigation research. Acknowledgements This research was supported by a grant [MPSS-NH-2015-81] through the Disaster and Safety Management Institute funded by Ministry of Public Safety and Security of Korean government.

  1. Geoheritage value of the UNESCO site at Leon Viejo and Momotombo volcano, Nicaragua (United States)

    van Wyk de Vries, Benjamin; Navarro, Martha; Espinoza, Eveling; Delgado, Hugo


    The Momotombo volcano has a special place in the history of Nicaragua. It is perfectly visible from the Capital, Managua, and from the major city of Leon. The old capital "Leon Viejo", founded in 1524 was abandoned in 1610, after a series of earthquakes and some major eruptions from Momotombo. The site was subsequently covered by Momotombo ash. A major geothermal power plant stands at the base of the volcano. Momotombo had been dormant for a hundred years, but had maintained high fumarole temperatures (900°C), indicating magma had been close to the surface for decades. In recent years, seismic activity has increased around the volcano. In December 2015, after a short ash eruption phase the volcano erupted lava, then a string of Vulcanian explosions. The volcano is now in a phase of small Vulcanian explosions and degassing. The Leon Viejo World Heritage site is at risk to mainly ash fall from the volcano, but the abandonment of the old city was primarily due to earthquakes. Additional risks come from high rainfall during hurricanes. There is an obvious link between the cultural site (inscribed under UNESCO cultural criteria) and the geological environment. First, the reactivation of Momotombo volcano makes it more important to revise the hazard of the site. At the same time, Leon Viejo can provide a portal for outreach related to the volcano and for geological risk in general. To maximise this, we provide a geosite inventory of the main features of Momotombo, and it's environs, that can be used as the first base for such studies. The volcano was visited by many adventure tourists before the 2015/2016 eruption, but is out of bounds at present. Alternative routes, around the volcano could be made, to adapt to the new situation and to show to visitors more of the geodiversity of this fascinating volcano-tectonic and cultural area.

  2. Novel experimental design for high pressure-high temperature electrical resistance measurements in a "Paris-Edinburgh" large volume press (United States)

    Matityahu, Shlomi; Emuna, Moran; Yahel, Eyal; Makov, Guy; Greenberg, Yaron


    We present a novel experimental design for high sensitivity measurements of the electrical resistance of samples at high pressures (0-6 GPa) and high temperatures (300-1000 K) in a "Paris-Edinburgh" type large volume press. Uniquely, the electrical measurements are carried out directly on a small sample, thus greatly increasing the sensitivity of the measurement. The sensitivity to even minor changes in electrical resistance can be used to clearly identify phase transitions in material samples. Electrical resistance measurements are relatively simple and rapid to execute and the efficacy of the present experimental design is demonstrated by measuring the electrical resistance of Pb, Sn, and Bi across a wide domain of temperature-pressure phase space and employing it to identify the loci of phase transitions. Based on these results, the phase diagrams of these elements are reconstructed to high accuracy and found to be in excellent agreement with previous studies. In particular, by mapping the locations of several well-studied reference points in the phase diagram of Sn and Bi, it is demonstrated that a standard calibration exists for the temperature and pressure, thus eliminating the need for direct or indirect temperature and pressure measurements. The present technique will allow simple and accurate mapping of phase diagrams under extreme conditions and may be of particular importance in advancing studies of liquid state anomalies.

  3. Flow Characterization of a Piezo-Electric High Speed Valve

    Directory of Open Access Journals (Sweden)

    T. Takiya


    Full Text Available Injecting a gas into fusion reactors or semiconductor manufacturing systems, one has to quickly control the flow rate by a piezoelectric valve. In order to construct a gas injection system with high speed valves in the future, performance tests have been conducted on a commercial piezoelectric valve. An orifice flowmeter for measuring time average flowrate and a hot wire anemometer for instantaneous flowrate were manufactured. The total flow coefficient of the orifice flowmeter was obtained experimentally under a low pressure of a 10-2 Pa and a low flowrate of a few mg/s, although they are smaller than the values specified by Japanese Industrial Standards. It is found that the hot wire anemometer installed downstream in the vicinity of the valve is suitable for detecting the change in flowrate with the response time of less than 1 ms.

  4. Real-time underwater object detection based on an electrically scanned high-resolution sonar

    DEFF Research Database (Denmark)

    Henriksen, Lars


    The paper describes an approach to real time detection and tracking of underwater objects, using image sequences from an electrically scanned high-resolution sonar. The use of a high resolution sonar provides a good estimate of the location of the objects, but strains the computers on board, beca...

  5. A Novel Series Connected Batteries State of High Voltage Safety Monitor System for Electric Vehicle Application

    Directory of Open Access Journals (Sweden)

    Qiang Jiaxi


    Full Text Available Batteries, as the main or assistant power source of EV (Electric Vehicle, are usually connected in series with high voltage to improve the drivability and energy efficiency. Today, more and more batteries are connected in series with high voltage, if there is any fault in high voltage system (HVS, the consequence is serious and dangerous. Therefore, it is necessary to monitor the electric parameters of HVS to ensure the high voltage safety and protect personal safety. In this study, a high voltage safety monitor system is developed to solve this critical issue. Four key electric parameters including precharge, contact resistance, insulation resistance, and remaining capacity are monitored and analyzed based on the equivalent models presented in this study. The high voltage safety controller which integrates the equivalent models and control strategy is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated, and the online electric parameters monitor strategy is analyzed and discussed. The test results indicate that the high voltage safety monitor system designed in this paper is suitable for EV application.

  6. Electrodynamic behavior and interface instability of double emulsion droplets under high electric field (United States)

    Abbasi, Muhammad Salman; Song, Ryungeun; Kim, Jaehoon; Lee, Jinkee


    In this paper, numerical solution of electro-dynamic behavior and interface instability of double emulsion droplet is presented. Level set method and leaky dielectric model coupled with Navier-Stokes equation are used to solve the electrodynamic problem. The method is validated against the theoretical analysis and the simulation results of the other researchers. Double emulsion droplet with inner droplet (core) and outer droplet (shell) phases immersed in continuous phase is subjected to high electric field. Shell/continuous and core/shell interfaces of the droplet undergo prolate-oblate or oblate-prolate deformation depending on the extent of the penetration of electric potential and sense of charge distribution at the interfaces. The deformation of the shell deviates from theory at larger volume fraction of core for oblate-prolate case whereas it follows theory for prolate-oblate case. The interfaces showing oblate-prolate deformation split away at the poles whereas, for prolate-oblate, they split at the equator. The re-union of the two split parts under high electric field results with production of daughter droplet at the core. The large decrease in critical electric field for oblate-prolate case shows their less interface stability at larger volume fraction of core. When the core is eccentric, the electric field drives it towards the shell center or to the shell/continuous interface depending on electrical parameters.

  7. [Analysis of Electric Stress in Human Head in High-frequency Low-power Electromagnetic Environment]. (United States)

    Zhou, Yongjun; Zhang, Hui; Niu, Zhongqi


    Action of electromagnetic radiation exerting on human body has been a concerned issue for people. Because electromagnetic waves could generate an electric stress in a discontinuous medium, we used the finite difference time domain (FDTD) as calculation methods to calculate the electric stress and its distribution in human head caused by high-frequency low-power electromagnetic environment, which was generated by dual-band (900 MHz and 1 800 MHz) PIFA antennas with radiated power 1 W, and we then performed the safety evaluation of cell phone radiation from the angle whether the electric stress further reached the human hearing threshold. The result showed that there existed the electric stress at the interface of different permittivity organization caused by the two kinds of high-frequency low-power electromagnetic environment and the maximum electric stress was located at the interface between skin and air of the phone side, and the electric stress peak at skull did not reach the threshold of auditory caused by bone tissue conduction so that it can not produce auditory effects.

  8. Improving electrical conductivity in polycarbonate nanocomposites using highly conductive PEDOT/PSS coated MWCNTs

    KAUST Repository

    Zhou, Jian


    We describe a strategy to design highly electrically conductive polycarbonate nanocomposites by using multiwalled carbon nanotubes (MWCNTs) coated with a thin layer of poly(3,4-ethylenedioxythiophene)/ poly(styrenesulfonate), a conductive polymer. We found that this coating method improves the electrical properties of the nanocomposites in two ways. First, the coating becomes the main electrical conductive path. Second, the coating promotes the formation of a percolation network at a low filler concentration (0.3 wt %). To tailor the electrical properties of the conductive polymer coating, we used a polar solvent ethylene glycol, and we can tune the final properties of the nanocomposite by controlling the concentrations of the elementary constituents or the intrinsic properties of the conductive polymer coating. This very flexible technique allows for tailoring the properties of the final product. © 2013 American Chemical Society.

  9. Design of High-Fidelity Testing Framework for Secure Electric Grid Control

    Energy Technology Data Exchange (ETDEWEB)

    Yoginath, Srikanth B [ORNL; Perumalla, Kalyan S [ORNL


    A solution methodology and implementation components are presented that can uncover unwanted, unintentional or unanticipated effects on electric grids from changes to actual electric grid control software. A new design is presented to leapfrog over the limitations of current modeling and testing techniques for cyber technologies in electric grids. We design a fully virtualized approach in which actual, unmodified operational software under test is enabled to interact with simulated surrogates of electric grids. It enables the software to influence the (simulated) grid operation and vice versa in a controlled, high fidelity environment. Challenges in achieving such capability include achieving low-overhead time control mechanisms in hypervisor schedulers, network capture and time-stamping, translation of network packets emanating from grid software into discrete events of virtual grid models, translation back from virtual sensors/actuators into data packets to control software, and transplanting the entire system onto an accurately and efficiently maintained virtual-time plane.

  10. Global Volcano Model (United States)

    Sparks, R. S. J.; Loughlin, S. C.; Cottrell, E.; Valentine, G.; Newhall, C.; Jolly, G.; Papale, P.; Takarada, S.; Crosweller, S.; Nayembil, M.; Arora, B.; Lowndes, J.; Connor, C.; Eichelberger, J.; Nadim, F.; Smolka, A.; Michel, G.; Muir-Wood, R.; Horwell, C.


    Over 600 million people live close enough to active volcanoes to be affected when they erupt. Volcanic eruptions cause loss of life, significant economic losses and severe disruption to people's lives, as highlighted by the recent eruption of Mount Merapi in Indonesia. The eruption of Eyjafjallajökull, Iceland in 2010 illustrated the potential of even small eruptions to have major impact on the modern world through disruption of complex critical infrastructure and business. The effects in the developing world on economic growth and development can be severe. There is evidence that large eruptions can cause a change in the earth's climate for several years afterwards. Aside from meteor impact and possibly an extreme solar event, very large magnitude explosive volcanic eruptions may be the only natural hazard that could cause a global catastrophe. GVM is a growing international collaboration that aims to create a sustainable, accessible information platform on volcanic hazard and risk. We are designing and developing an integrated database system of volcanic hazards, vulnerability and exposure with internationally agreed metadata standards. GVM will establish methodologies for analysis of the data (eg vulnerability indices) to inform risk assessment, develop complementary hazards models and create relevant hazards and risk assessment tools. GVM will develop the capability to anticipate future volcanism and its consequences. NERC is funding the start-up of this initiative for three years from November 2011. GVM builds directly on the VOGRIPA project started as part of the GRIP (Global Risk Identification Programme) in 2004 under the auspices of the World Bank and UN. Major international initiatives and partners such as the Smithsonian Institution - Global Volcanism Program, State University of New York at Buffalo - VHub, Earth Observatory of Singapore - WOVOdat and many others underpin GVM.

  11. Development of high energy density electrical double layer capacitors (United States)

    Devarajan, Thamarai selvi

    Electrochemical Double Layer capacitors (EDLCs) have shown themselves as a viable energy storage alternative. EDLCs have high power density, faster charge/discharge, wide operating temperature and long cycle life compared to batteries since it stores charge by physical separation. Despites all their advantages, their low energy density stand as a bottleneck for capacitors. This research aims to increase the energy density of EDLC without compromising the power density. Energy is proportional to the square of cell voltage. Cell voltage is mainly dependent on electrolyte breakdown. Electrolytes also provide ions for charge separation and conduction. Therefore various electrolytes (Solutes and Solvents) which can give high concentration, solubility and decomposition potential were characterized in the first part of the research. In that study, a novel ionic liquid OPBF4 had higher capacitance and comparable voltage window compared to commercial TEABF4 in Acetonitrile. However, the increased polarity of the fixed ring O-atom and the ion-ion interaction in OPBF4 was responsible for lowering its conductivity. Oxygenated ionic compounds with alkyl groups had lower stability due to beta elimination between two electron withdrawing atoms. Volume based thermodynamics and quantum chemical calculations were used to calculate ion size, HOMO/LUMO energies, and free energy changes and establish relationship with capacitance, redox potential and melting points respectively. In addition free energy of fusion was used to predict the melting point. Ion size had correlation with capacitance due to compact double layer formation. Free energy changes did not explain the differences in melting point and predicted dielectric constant was inconsistent with the polarity. This is presumably due to using Van der Waals volume instead of crystal structure volume and insufficient incorporation of polarization term. The HOMO/LUMO energies gave direct relation between oxidation and reduction

  12. Electric Grid Expansion Planning with High Levels of Variable Generation

    Energy Technology Data Exchange (ETDEWEB)

    Hadley, Stanton W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); You, Shutang [Univ. of Tennessee, Knoxville, TN (United States); Shankar, Mallikarjun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, Yilu [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)


    Renewables are taking a large proportion of generation capacity in U.S. power grids. As their randomness has increasing influence on power system operation, it is necessary to consider their impact on system expansion planning. To this end, this project studies the generation and transmission expansion co-optimization problem of the US Eastern Interconnection (EI) power grid with a high wind power penetration rate. In this project, the generation and transmission expansion problem for the EI system is modeled as a mixed-integer programming (MIP) problem. This study analyzed a time series creation method to capture the diversity of load and wind power across balancing regions in the EI system. The obtained time series can be easily introduced into the MIP co-optimization problem and then solved robustly through available MIP solvers. Simulation results show that the proposed time series generation method and the expansion co-optimization model and can improve the expansion result significantly after considering the diversity of wind and load across EI regions. The improved expansion plan that combines generation and transmission will aid system planners and policy makers to maximize the social welfare. This study shows that modelling load and wind variations and diversities across balancing regions will produce significantly different expansion result compared with former studies. For example, if wind is modeled in more details (by increasing the number of wind output levels) so that more wind blocks are considered in expansion planning, transmission expansion will be larger and the expansion timing will be earlier. Regarding generation expansion, more wind scenarios will slightly reduce wind generation expansion in the EI system and increase the expansion of other generation such as gas. Also, adopting detailed wind scenarios will reveal that it may be uneconomic to expand transmission networks for transmitting a large amount of wind power through a long distance

  13. Comparison of High-Fidelity Computational Tools for Wing Design of a Distributed Electric Propulsion Aircraft (United States)

    Deere, Karen A.; Viken, Sally A.; Carter, Melissa B.; Viken, Jeffrey K.; Derlaga, Joseph M.; Stoll, Alex M.


    A variety of tools, from fundamental to high order, have been used to better understand applications of distributed electric propulsion to aid the wing and propulsion system design of the Leading Edge Asynchronous Propulsion Technology (LEAPTech) project and the X-57 Maxwell airplane. Three high-fidelity, Navier-Stokes computational fluid dynamics codes used during the project with results presented here are FUN3D, STAR-CCM+, and OVERFLOW. These codes employ various turbulence models to predict fully turbulent and transitional flow. Results from these codes are compared for two distributed electric propulsion configurations: the wing tested at NASA Armstrong on the Hybrid-Electric Integrated Systems Testbed truck, and the wing designed for the X-57 Maxwell airplane. Results from these computational tools for the high-lift wing tested on the Hybrid-Electric Integrated Systems Testbed truck and the X-57 high-lift wing presented compare reasonably well. The goal of the X-57 wing and distributed electric propulsion system design achieving or exceeding the required ?? (sub L) = 3.95 for stall speed was confirmed with all of the computational codes.

  14. Optimizing the U.S. Electric System with a High Penetration of Renewables (United States)

    Corcoran, B. A.; Jacobson, M. Z.


    As renewable energy generators are increasingly being installed throughout the U.S., there is growing interest in interconnecting diverse renewable generators (primarily wind and solar) across large geographic areas through an enhanced transmission system. This reduces variability in the aggregate power output, increases system reliability, and allows for the development of the best overall group of renewable technologies and sites to meet the load. Studies are therefore needed to determine the most efficient and economical plan to achieve large area interconnections in a future electric system with a high penetration of renewables. This research quantifies the effects of aggregating electric load together with diverse renewable generation throughout the ten Federal Energy Regulatory Commission (FERC) regions in the contiguous U.S. A deterministic linear program has been built in AMPL (A Mathematical Programming Language) to solve for the least-cost organizational structure and system (generators, transmission, and storage) for a highly renewable electric grid. The analysis will 1) examine a highly renewable 2006 electric system, including various sensitivity cases and additional system components such as additional load from electric vehicles, and 2) create a 'roadmap' from the existing 2006 system to a highly renewable system in 2030, accounting for projected price and demand changes and generator retirements based on age and environmental regulations. Ideally, results from this study will offer insight for a federal renewable energy policy (such as a renewable portfolio standard) and how to best organize U.S. regions for transmission planning.

  15. High voltage bus and auxiliary heater control system for an electric or hybrid vehicle (United States)

    Murty, Balarama Vempaty


    A control system for an electric or hybrid electric vehicle includes a vehicle system controller and a control circuit having an electric immersion heater. The heater is electrically connected to the vehicle's high voltage bus and is thermally coupled to a coolant loop containing a heater core for the vehicle's climate control system. The system controller responds to cabin heat requests from the climate control system by generating a pulse width modulated signal that is used by the control circuit to operate the heater at a duty cycle appropriate for the amount of cabin heating requested. The control system also uses the heater to dissipate excess energy produced by an auxiliary power unit and to provide electric braking when regenerative braking is not desirable and manual braking is not necessary. The control system further utilizes the heater to provide a safe discharge of a bank of energy storage capacitors following disconnection of the battery or one of the high voltage connectors used to transmit high voltage operating power to the various vehicle systems. The control circuit includes a high voltage clamping circuit that monitors the voltage on the bus and operates the heater to clamp down the bus voltage when it exceeds a pre-selected maximum voltage. The control system can also be used to phase in operation of the heater when the bus voltage exceeds a lower threshold voltage and can be used to phase out the auxiliary power unit charging and regenerative braking when the battery becomes fully charged.

  16. Dehydration of chlorite explains anomalously high electrical conductivity in the mantle wedges. (United States)

    Manthilake, Geeth; Bolfan-Casanova, Nathalie; Novella, Davide; Mookherjee, Mainak; Andrault, Denis


    Mantle wedge regions in subduction zone settings show anomalously high electrical conductivity (~1 S/m) that has often been attributed to the presence of aqueous fluids released by slab dehydration. Laboratory-based measurements of the electrical conductivity of hydrous phases and aqueous fluids are significantly lower and cannot readily explain the geophysically observed anomalously high electrical conductivity. The released aqueous fluid also rehydrates the mantle wedge and stabilizes a suite of hydrous phases, including serpentine and chlorite. In this present study, we have measured the electrical conductivity of a natural chlorite at pressures and temperatures relevant for the subduction zone setting. In our experiment, we observe two distinct conductivity enhancements when chlorite is heated to temperatures beyond its thermodynamic stability field. The initial increase in electrical conductivity to ~3 × 10(-3) S/m can be attributed to chlorite dehydration and the release of aqueous fluids. This is followed by a unique, subsequent enhancement of electrical conductivity of up to 7 × 10(-1) S/m. This is related to the growth of an interconnected network of a highly conductive and chemically impure magnetite mineral phase. Thus, the dehydration of chlorite and associated processes are likely to be crucial in explaining the anomalously high electrical conductivity observed in mantle wedges. Chlorite dehydration in the mantle wedge provides an additional source of aqueous fluid above the slab and could also be responsible for the fixed depth (120 ± 40 km) of melting at the top of the subducting slab beneath the subduction-related volcanic arc front.

  17. Mount Rainier: A decade volcano (United States)

    Swanson, Donald A.; Malone, Stephen D.; Samora, Barbara A.

    Mount Rainier, the highest (4392 m) volcano in the Cascade Range, towers over a population of more than 2.5 million in the Seattle-Tacoma metropolitan area, and its drainage system via the Columbia River potentially affects another 500,000 residents of southwestern Washington and northwestern Oregon (Figure 1). Mount Rainier is the most hazardous volcano in the Cascades in terms of its potential for magma-water interaction and sector collapse. Major eruptions, or debris flows even without eruption, pose significant dangers and economic threats to the region. Despite such hazard and risk, Mount Rainier has received little study; such important topics as its petrologic and geochemical character, its proximal eruptive history, its susceptibility to major edifice failure, and its development over time have been barely investigated. This situation may soon change because of Mount Rainier's recent designation as a “Decade Volcano.”

  18. Systematic radon survey over active volcanoes

    Energy Technology Data Exchange (ETDEWEB)

    Seidel, J.L.; Monnin, M.; Garcia Vindas, J.R. [Centre National de la Recherche Cientifique, Montpellier (France). Lab. GBE; Ricard, L.P.; Staudacher, T. [Observatoire Volcanologique Du Pitou de la Fournaise, La Plaine des Cafres (France)


    Data obtained since 1993 on Costa Rica volcanos are presented and radon anomalies recorded before the eruption of the Irazu volcano (December 8, 1994) are discussed. The Piton de la Fournaise volcano is inactive since mid 1992. The influence of the external parameters on the radon behaviour is studied and the type of perturbations induced on short-term measurements are individuate.

  19. A promising structure for fabricating high strength and high electrical conductivity copper alloys. (United States)

    Li, Rengeng; Kang, Huijun; Chen, Zongning; Fan, Guohua; Zou, Cunlei; Wang, Wei; Zhang, Shaojian; Lu, Yiping; Jie, Jinchuan; Cao, Zhiqiang; Li, Tingju; Wang, Tongmin


    To address the trade-off between strength and electrical conductivity, we propose a strategy: introducing precipitated particles into a structure composed of deformation twins. A Cu-0.3%Zr alloy was designed to verify our strategy. Zirconium was dissolved into a copper matrix by solution treatment prior to cryorolling and precipitated in the form of Cu5Zr from copper matrix via a subsequent aging treatment. The microstructure evolutions of the processed samples were investigated by transmission electron microscopy and X-ray diffraction analysis, and the mechanical and physical behaviours were evaluated through tensile and electrical conductivity tests. The results demonstrated that superior tensile strength (602.04 MPa) and electrical conductivity (81.4% IACS) was achieved. This strategy provides a new route for balancing the strength and electrical conductivity of copper alloys, which can be developed for large-scale industrial application.

  20. A Novel Method for Measuring Electrical Conductivity of High Insulating Oil Using Charge Decay (United States)

    Wang, Z. Q.; Qi, P.; Wang, D. S.; Wang, Y. D.; Zhou, W.


    For the high insulating oil, it is difficult to measure the conductivity precisely using voltammetry method. A high-precision measurementis proposed for measuring bulk electrical conductivity of high insulating oils (about 10-9--10-15S/m) using charge decay. The oil is insulated and charged firstly, and then grounded fully. During the experimental procedure, charge decay is observed to show an exponential law according to "Ohm" theory. The data of time dependence of charge density is automatically recorded using an ADAS and a computer. Relaxation time constant is fitted from the data using Gnuplot software. The electrical conductivity is calculated using relaxation time constant and dielectric permittivity. Charge density is substituted by electric potential, considering charge density is difficult to measure. The conductivity of five kinds of oils is measured. Using this method, the conductivity of diesel oil is easily measured to beas low as 0.961 pS/m, as shown in Fig. 5.

  1. The Thawing Characteristic of Frozen Tofu under High-Voltage Alternating Electric Field

    Directory of Open Access Journals (Sweden)

    Shilong Deng


    Full Text Available To systematically and comprehensively investigate the high voltage alternating electric field (HVAEF thawing processing, we investigated the high-voltage electric field thawing characteristic of the frozen tofu at different voltages for alternating current (AC. The thawing time, thawing loss of frozen tofu, and specific energy consumption (SEC of HVEF system were measured. Seven different mathematical models were then compared to simulate thawing time curves based on root mean square error, reduced mean square of deviation, and modeling efficiency. The results showed that the thawing rate of frozen tofu was notably greater in the high-voltage electric field system when compared to control. Both Linear and Quadratic models were the best mathematical models. Therefore, this work presents a facile and effective strategy for experimentally and theoretically determining the HVAEF thawing properties of frozen tofu.

  2. Alaska volcanoes guidebook for teachers (United States)

    Adleman, Jennifer N.


    Alaska’s volcanoes, like its abundant glaciers, charismatic wildlife, and wild expanses inspire and ignite scientific curiosity and generate an ever-growing source of questions for students in Alaska and throughout the world. Alaska is home to more than 140 volcanoes, which have been active over the last 2 million years. About 90 of these volcanoes have been active within the last 10,000 years and more than 50 of these have been active since about 1700. The volcanoes in Alaska make up well over three-quarters of volcanoes in the United States that have erupted in the last 200 years. In fact, Alaska’s volcanoes erupt so frequently that it is almost guaranteed that an Alaskan will experience a volcanic eruption in his or her lifetime, and it is likely they will experience more than one. It is hard to imagine a better place for students to explore active volcanism and to understand volcanic hazards, phenomena, and global impacts. Previously developed teachers’ guidebooks with an emphasis on the volcanoes in Hawaii Volcanoes National Park (Mattox, 1994) and Mount Rainier National Park in the Cascade Range (Driedger and others, 2005) provide place-based resources and activities for use in other volcanic regions in the United States. Along the lines of this tradition, this guidebook serves to provide locally relevant and useful resources and activities for the exploration of numerous and truly unique volcanic landscapes in Alaska. This guidebook provides supplemental teaching materials to be used by Alaskan students who will be inspired to become educated and prepared for inevitable future volcanic activity in Alaska. The lessons and activities in this guidebook are meant to supplement and enhance existing science content already being taught in grade levels 6–12. Correlations with Alaska State Science Standards and Grade Level Expectations adopted by the Alaska State Department of Education and Early Development (2006) for grades six through eleven are listed at

  3. Effects of High-voltage Pulse Electric Field Treatment on the Structure Stability of Konjac Glucomannan

    Institute of Scientific and Technical Information of China (English)

    YAO Min-Na; FAN Lin-Lin; LIU Ya-Nan; CHEN Qing-Ai; ZENG Yuan; JIAN Wen-Jie; PANG Jie


    Structures of KGM treated in two high-voltage pulse electric fields were characterized by infrared spectroscopy,Raman spectroscopy,X-ray diffraction and so on.The results showed that intermolecular hydrogen bonding interactions of KGM were reduced after being treated with high-voltage pulse electric field,but there was no significant effect on its fiber chain form and thermal characteristics.Results of the study can provide a useful reference for further study on the structure and property of KGM,and especially can provide theoretical basis for the effect of physical field on the foodstuff deep processing related to KGM.

  4. Lustrous copper nanoparticle film: Photodeposition with high quantum yield and electric conductivity (United States)

    Miyagawa, Masaya; Yonemura, Mari; Tanaka, Hideki


    Cu nanoparticle (NP) film has attracted much attention due to its high electric conductivity. In the present study, we prepared a Cu NP film on a TiO2-coated substrate by photoreduction of copper acetate solution. The obtained film showed high electric conductivity and metallic luster by the successive deposition of Cu NP. Moreover, the film was decomposed on exposure to fresh air, and its decomposition reaction mechanisms were proposed. Hence, we concluded that the obtained lustrous film was composed of Cu NP, even though its physical properties was similar to bulk copper.

  5. Insulation co-ordination in high-voltage electric power systems

    CERN Document Server

    Diesendorf, W


    Insulation Co-ordination in High-Voltage Electric Power Systems deals with the methods of insulation needed in different circumstances. The book covers topics such as overvoltages and lightning surges; disruptive discharge and withstand voltages; self-restoring and non-self-restoring insulation; lightning overvoltages on transmission lines; and the attenuation and distortion of lightning surges. Also covered in the book are topics such as the switching surge designs of transmission lines, as well as the insulation coordination of high-voltage stations. The text is recommended for electrical en

  6. Kink effect in AlGaN/GaN high electron mobility transistors by electrical stress

    Institute of Scientific and Technical Information of China (English)

    Ma Xiao-Hua; Ma Ji-Gang; Yang Li-Yuan; He Qiang; Jiao Ying; Ma Ping; Hao Yue


    The kink effect is studied in an AlGaN/GaN high electron mobility transistor by measuring DC performance during fresh, short-term stress and recovery cycle with negligible degradation. Vdg plays an assistant role in detrapping electrons and short-term stress results in no creation of new category traps but an increase in number of active traps.A possible mechanism is proposed that electrical stress supplies traps with the electric field for activation and when device is under test field-assisted hot-electrons result in electrons detrapping from traps, thus deteriorating the kink effect. In addition, experiments show that the impact ionization is at a relatively low level, which is not the dominant mechanism compared with trapping effect. We analyse the complicated link between the kink effect and stress bias through groups of electrical stress states: Vds = 0-state, off-state, on-state (on-state with low voltage, high-power state,high field state). Finlly, a conclusion is drawn that electric field brings about more severe kink effect than hot electrons.With the assistance of electric field, hot electrons tend to be possible to modulate the charges in deep-level trap.

  7. Segregated Planktonic and Bottom-Dwelling Archaeal Communities in High-Temperature Acidic/Sulfuric Ponds of the Tatun Volcano Group, Northern Taiwan

    Directory of Open Access Journals (Sweden)

    Ting-Wen Cheng


    Full Text Available Geothermal environments are characterized by dynamic redox and temperature fluctuations inherited from the exposure of deeply-sourced, hot, reducing fluids to low-temperature, oxidizing ambient environments. To investigate whether microbial assemblages shifted in response to the changes of a redox state within acidic hot ponds, we collected three paired water and sediment samples from the Tatun Volcano Group, assessed metabolic roles of community members, and correlated their functional capabilities with geochemical factors along depth. Molecular analyses revealed that Sulfolobus spp., Acidianus spp. and Vulcanisaeta spp. capable of respiring elemental sulfur under oxic and/or low-oxygen conditions were the major archaeal members in planktonic communities. In contrast, obligate anaerobic Caldisphaera spp. dominated over others in bottom-dwelling communities. Bacteria were only detected in one locality wherein the majority was affiliated with microaerophilic Hydrogenobaculum spp. Cluster analyses indicated that archaeal communities associated with sediments tended to cluster together and branch off those with water. In addition, the quantities of dissolved oxygen within the water column were substantially less than those in equilibrium with atmospheric oxygen, indicating a net oxygen consumption most likely catalyzed by microbial processes. These lines of evidence suggest that the segregation of planktonic from bottom-dwelling archaeal assemblages could be accounted for by the oxygen affinities inherited in individual archaeal members. Community assemblages in geothermal ecosystems would be often underrepresented without cautious sampling of both water and sediments.

  8. Modeling volcano growth on the Island of Hawaii: deep-water perspectives (United States)

    Lipman, Peter W.; Calvert, Andrew T.


    Recent ocean-bottom geophysical surveys, dredging, and dives, which complement surface data and scientific drilling at the Island of Hawaii, document that evolutionary stages during volcano growth are more diverse than previously described. Based on combining available composition, isotopic age, and geologically constrained volume data for each of the component volcanoes, this overview provides the first integrated models for overall growth of any Hawaiian island. In contrast to prior morphologic models for volcano evolution (preshield, shield, postshield), growth increasingly can be tracked by age and volume (magma supply), defining waxing alkalic, sustained tholeiitic, and waning alkalic stages. Data and estimates for individual volcanoes are used to model changing magma supply during successive compositional stages, to place limits on volcano life spans, and to interpret composite assembly of the island. Volcano volumes vary by an order of magnitude; peak magma supply also varies sizably among edifices but is challenging to quantify because of uncertainty about volcano life spans. Three alternative models are compared: (1) near-constant volcano propagation, (2) near-equal volcano durations, (3) high peak-tholeiite magma supply. These models define inconsistencies with prior geodynamic models, indicate that composite growth at Hawaii peaked ca. 800–400 ka, and demonstrate a lower current rate. Recent age determinations for Kilauea and Kohala define a volcano propagation rate of 8.6 cm/yr that yields plausible inception ages for other volcanoes of the Kea trend. In contrast, a similar propagation rate for the less-constrained Loa trend would require inception of Loihi Seamount in the future and ages that become implausibly large for the older volcanoes. An alternative rate of 10.6 cm/yr for Loa-trend volcanoes is reasonably consistent with ages and volcano spacing, but younger Loa volcanoes are offset from the Kea trend in age-distance plots. Variable magma flux

  9. Mud Volcanoes as Exploration Targets on Mars (United States)

    Allen, Carlton C.; Oehler, Dorothy Z.


    Tens of thousands of high-albedo mounds occur across the southern part of the Acidalia impact basin on Mars. These structures have geologic, physical, mineralogic, and morphologic characteristics consistent with an origin from a sedimentary process similar to terrestrial mud volcanism. The potential for mud volcanism in the Northern Plains of Mars has been recognized for some time, with candidate mud volcanoes reported from Utopia, Isidis, northern Borealis, Scandia, and the Chryse-Acidalia region. We have proposed that the profusion of mounds in Acidalia is a consequence of this basin's unique geologic setting as the depocenter for the tune fraction of sediments delivered by the outflow channels from the highlands.

  10. Imaging magma plumbing beneath Askja volcano, Iceland (United States)

    Greenfield, Tim; White, Robert S.


    Volcanoes during repose periods are not commonly monitored by dense instrumentation networks and so activity during periods of unrest is difficult to put in context. We have operated a dense seismic network of 3-component, broadband instruments around Askja, a large central volcano in the Northern Volcanic Zone, Iceland, since 2006. Askja last erupted in 1961, with a relatively small basaltic lava flow. Since 1975 the central caldera has been subsiding and there has been no indication of volcanic activity. Despite this, Askja has been one of the more seismically active volcanoes in Iceland. The majority of these events are due to an extensive geothermal area within the caldera and tectonically induced earthquakes to the northeast which are not related to the magma plumbing system. More intriguing are the less numerous deeper earthquakes at 12-24km depth, situated in three distinct areas within the volcanic system. These earthquakes often show a frequency content which is lower than the shallower activity, but they still show strong P and S wave arrivals indicative of brittle failure, despite their location being well below the brittle-ductile boundary, which, in Askja is ~7km bsl. These earthquakes indicate the presence of melt moving or degassing at depth while the volcano is not inflating, as only high strain rates or increased pore fluid pressures would cause brittle fracture in what is normally an aseismic region in the ductile zone. The lower frequency content must be the result of a slower source time function as earthquakes which are both high frequency and low frequency come from the same cluster, thereby discounting a highly attenuating lower crust. To image the plumbing system beneath Askja, local and regional earthquakes have been used as sources to solve for the velocity structure beneath the volcano. Travel-time tables were created using a finite difference technique and the residuals were used to solve simultaneously for both the earthquake locations

  11. External Electric Field-Assisted Laser Percussion Drilling for Highly Reflective Metals

    Directory of Open Access Journals (Sweden)

    Chao-Ching Ho


    Full Text Available In this study, an external electric field was employed during the laser percussion drilling on highly reflective materials. The laser-produced plasma was sputtered substantially, and the charged ions in the plasma plume were drawn by the electrodes. Different configurations of plate electrodes were proposed and investigated in this work to provide a simple, low-cost method that allows expelling the laser-induced plasma during the percussion drilling process. The electric field resulted from the potential that was applied across the two electrodes. This electrical perturbation produced a uniform electric field when the laser-generated plasma was created in the plane plate-charged capacitor. The electric field with different electrode configurations applied to the charged particles that are carrying the electrons was also simulated in this work. All processing work was performed in air under standard atmospheric conditions and in the absence of assisting process gas. The depth of the holes drilled when various types of electrode configurations were used was measured, and the results were used to evaluate the percussion drilling rate. Results show that vaporized debris is expelled by the applied electric field; hence, in optimal configuration the penetration depth can be increased by up to 91.1%.

  12. Structure characteristics of electrical treeing in XLPE insulation under high frequencies (United States)

    Bao, Minghui; Yin, Xiaogen; He, Junjia


    Electrical tree structure is one of the most important influencing factors for electrical treeing characteristics in polymers. In this paper, we focused on the structure characteristics of electrical treeing in cross-linked polyethylene (XLPE) insulation under high-frequency voltages. The tree structure characteristics include structure distribution characteristics and structure conversion characteristics. The influences of voltage, frequency, and pin-plane spacing on tree structure characteristics were analyzed based on the experimental results. It can be concluded that tree structures regularly change with the local electric field and frequency. The electric field in a very small zone near the needle tip is an important influencing factor for the formation of bush-like trees, and the lowest frequencies for the observed pure-vine-like trees increased with voltage. For double-structure trees, the local electric field at the transition location of the two structures remained almost unchanged with voltage and pin-plane spacing, but obviously increased with frequency. In order to investigate the relations of the growth rate and fractal dimension with tree structure characteristics, a new parameter, the energy threshold Wt, has been introduced and calculated for different tree structures.

  13. Mount Meager Volcano, Canada: a Case Study for Landslides on Glaciated Volcanoes (United States)

    Roberti, G. L.; Ward, B. C.; van Wyk de Vries, B.; Falorni, G.; Perotti, L.; Clague, J. J.


    Mount Meager is a strato-volcano massif in the Northern Cascade Volcanic Arc (Canada) that erupted in 2350 BP, the most recent in Canada. To study the stability of the Massif an international research project between France ( Blaise Pascal University), Italy (University of Turin) and Canada (Simon Fraser University) and private companies (TRE - sensing the planet) has been created. A complex history of glacial loading and unloading, combined with weak, hydrothermally altered rocks has resulted in a long record of catastrophic landslides. The most recent, in 2010 is the third largest (50 x 106 m3) historical landslide in Canada. Mount Meager is a perfect natural laboratory for gravity and topographic processes such as landslide activity, permafrost and glacial dynamics, erosion, alteration and uplift on volcanoes. Research is aided by a rich archive of aerial photos of the Massif (1940s up to 2006): complete coverage approximately every 10 years. This data set has been processed and multi-temporal, high resolution Orthophoto and DSMs (Digital Surface Models) have been produced. On these digital products, with the support on field work, glacial retreat and landslide activity have been tracked and mapped. This has allowed for the inventory of unstable areas, the identification of lava flows and domes, and the general improvement on the geologic knowledge of the massif. InSAR data have been used to monitor the deformation of the pre-2010 failure slope. It will also be used to monitor other unstable slopes that potentially can evolve to catastrophic collapses of up to 1 km3 in volume, endangering local communities downstream the volcano. Mount Meager is definitively an exceptional site for studying the dynamics of a glaciated, uplifted volcano. The methodologies proposed can be applied to other volcanic areas with high erosion rates such as Alaska, Cascades, and the Andes.

  14. The 2013 eruption of Pavlof Volcano, Alaska: a spatter eruption at an ice- and snow-clad volcano (United States)

    Waythomas, Christopher F.; Haney, Matthew M.; Fee, David; Schneider, David J.; Wech, Aaron G.


    The 2013 eruption of Pavlof Volcano, Alaska began on 13 May and ended 49 days later on 1 July. The eruption was characterized by persistent lava fountaining from a vent just north of the summit, intermittent strombolian explosions, and ash, gas, and aerosol plumes that reached as high as 8 km above sea level and on several occasions extended as much as 500 km downwind of the volcano. During the first several days of the eruption, accumulations of spatter near the vent periodically collapsed to form small pyroclastic avalanches that eroded and melted snow and ice to form lahars on the lower north flank of the volcano. Continued lava fountaining led to the production of agglutinate lava flows that extended to the base of the volcano, about 3–4 km beyond the vent. The generation of fountain-fed lava flows was a dominant process during the 2013 eruption; however, episodic collapse of spatter accumulations and formation of hot spatter-rich granular avalanches was a more efficient process for melting snow and ice and initiating lahars. The lahars and ash plumes generated during the eruption did not pose any serious hazards for the area. However, numerous local airline flights were cancelled or rerouted, and trace amounts of ash fall occurred at all of the local communities surrounding the volcano, including Cold Bay, Nelson Lagoon, Sand Point, and King Cove.

  15. The Unexpected Awakening of Chaitén Volcano, Chile (United States)

    Carn, Simon A.; Zogorski, John S.; Lara, Luis; Ewert, John W.; Watt, Sebastian; Prata, Alfred J.; Thomas, Ronald J.; Villarosa, Gustavo


    On 2 May 2008, a large eruption began unexpectedly at the inconspicuous Chaitén volcano in Chile's southern volcanic zone. Ash columns abruptly jetted from the volcano into the stratosphere, followed by lava dome effusion and continuous low-altitude ash plumes [Lara, 2009]. Apocalyptic photographs of eruption plumes suffused with lightning were circulated globally. Effects of the eruption were extensive. Floods and lahars inundated the town of Chaitén, and its 4625 residents were evacuated. Widespread ashfall and drifting ash clouds closed regional airports and cancelled hundreds of domestic flights in Argentina and Chile and numerous international flights [Guffanti et al., 2008]. Ash heavily affected the aquaculture industry in the nearby Gulf of Corcovado, curtailed ecotourism, and closed regional nature preserves. To better prepare for future eruptions, the Chilean government has boosted support for monitoring and hazard mitigation at Chaitén and at 42 other highly hazardous, active volcanoes in Chile.

  16. The Unexpected Awakening of Chaitén Volcano, Chile (United States)

    Carn, Simon A.; Pallister, John S.; Lara, Luis; Ewert, John W.; Watt, Sebastian; Prata, Alfred J.; Thomas, Ronald J.; Villarosa, Gustavo


    On 2 May 2008, a large eruption began unexpectedly at the inconspicuous Chaitén volcano in Chile's southern volcanic zone. Ash columns abruptly jetted from the volcano into the stratosphere, followed by lava dome effusion and continuous low-altitude ash plumes [Lara, 2009]. Apocalyptic photographs of eruption plumes suffused with lightning were circulated globally. Effects of the eruption were extensive. Floods and lahars inundated the town of Chaitén, and its 4625 residents were evacuated. Widespread ashfall and drifting ash clouds closed regional airports and cancelled hundreds of domestic flights in Argentina and Chile and numerous international flights [Guffanti et al., 2008]. Ash heavily affected the aquaculture industry in the nearby Gulf of Corcovado, curtailed ecotourism, and closed regional nature preserves. To better prepare for future eruptions, the Chilean government has boosted support for monitoring and hazard mitigation at Chaitén and at 42 other highly hazardous, active volcanoes in Chile.

  17. Polarizing Oxygen Vacancies in Insulating Metal Oxides under a High Electric Field (United States)

    Youssef, Mostafa; Van Vliet, Krystyn J.; Yildiz, Bilge


    We demonstrate a thermodynamic formulation to quantify defect formation energetics in an insulator under a high electric field. As a model system, we analyzed neutral oxygen vacancies (color centers) in alkaline-earth-metal binary oxides using density functional theory, Berry phase calculations, and maximally localized Wannier functions. The work of polarization lowers the field-dependent electric Gibbs energy of formation of this defect. This is attributed mainly to the ease of polarizing the two electrons trapped in the vacant site, and secondarily to the defect induced reduction in bond stiffness and softening of phonon modes. The formulation and analysis have implications for understanding the behavior of insulating oxides in electronic, magnetic, catalytic, and electrocaloric devices under a high electric field.

  18. Optimizing the U.S. Electric System with a High Penetration of Renewables (United States)

    Corcoran, B. A.; Jacobson, M. Z.


    As renewable energy generators are increasingly being installed throughout the U.S., there is growing interest in interconnecting diverse renewable generators (primarily wind and solar) across large geographic areas through an enhanced transmission system. This reduces variability in the aggregate power output, increases system reliability, and allows for the development of the best overall group of renewable technologies and sites to meet the load. Studies are therefore needed to determine the most efficient and economical plan to achieve large area interconnections in a future electric system with a high penetration of renewables. This research quantifies the effects of aggregating electric load and, separately, electric load together with diverse renewable generation throughout the ten Federal Energy Regulatory Commission (FERC) regions in the contiguous U.S. The effects of aggregating electric load alone -- including generator capacity capital cost savings, load energy shift operating cost savings, reserve requirement cost savings, and transmission costs -- were calculated for various groupings of FERC regions using 2006 data. Transmission costs outweighed cost savings due to aggregation in nearly all cases. East-west transmission layouts had the highest overall cost, and interconnecting ERCOT to adjacent FERC regions resulted in increased costs, both due to limited existing transmission capacity. Scenarios consisting of smaller aggregation groupings had the lowest overall cost. This analysis found no economic case for further aggregation of load alone within the U.S., except possibly in the West and Northwest. If aggregation of electric load is desired, then small, regional consolidations yield the lowest overall system cost. Next, the effects of aggregating electric load together with renewable electricity generation are being quantified through the development and use of an optimization tool in AMPL (A Mathematical Programming Language). This deterministic

  19. Bilateral upper limb amputations in victims of high tension electrical injuries: Three case studies

    Directory of Open Access Journals (Sweden)

    Cajetan Nwadinigwe


    Full Text Available Bilateral upper limb amputations result in severe disability. High voltage electrical injury is a rare cause of such an outcome and injuries often occur as occupational hazards. We present three case reports of accidental high voltage injuries that occurred in a non-occupational setting. Victims were all initially managed at other centres before referral to our hospital and all subsequently had bilateral upper limb amputations. The high cost of treatment, importance of prevention, and need for rehabilitation are highlighted.

  20. Survey of high pressure using dual cora sensors and the differentiator electric bridge (United States)

    Sun, Cheng-Yuan


    In this paper, the possible survey of a high-pressure field by using dual core fiber sensors and a differentiator electric bridge is described. Also, the interaction between high-pressure field and a dual core fiber nonlinear coupler is discussed, using the analyzed theory. We have obtained the formula of the theory and some correlative experimental results. We can measure high-pressure (2.2 * 106 V) by using dual core fiber sensors and a differentiator bridge.

  1. Geology of El Chichon volcano, Chiapas, Mexico (United States)

    Duffield, W.A.; Tilling, R.I.; Canul, R.


    The (pre-1982) 850-m-high andesitic stratovolcano El Chicho??n, active during Pleistocene and Holocene time, is located in rugged, densely forested terrain in northcentral Chiapas, Me??xico. The nearest neighboring Holocene volcanoes are 275 km and 200 km to the southeast and northwest, respectively. El Chicho??n is built on Tertiary siltstone and sandstone, underlain by Cretaceous dolomitic limestone; a 4-km-deep bore hole near the east base of the volcano penetrated this limestone and continued 770 m into a sequence of Jurassic or Cretaceous evaporitic anhydrite and halite. The basement rocks are folded into generally northwest-trending anticlines and synclines. El Chicho??n is built over a small dome-like structure superposed on a syncline, and this structure may reflect cumulative deformation related to growth of a crustal magma reservoir beneath the volcano. The cone of El Chicho??n consists almost entirely of pyroclastic rocks. The pre-1982 cone is marked by a 1200-m-diameter (explosion?) crater on the southwest flank and a 1600-m-diameter crater apparently of similar origin at the summit, a lava dome partly fills each crater. The timing of cone and dome growth is poorly known. Field evidence indicates that the flank dome is older than the summit dome, and K-Ar ages from samples high on the cone suggest that the flank dome is older than about 276,000 years. At least three pyroclastic eruptions have occurred during the past 1250 radiocarbon years. Nearly all of the pyroclastic and dome rocks are moderately to highly porphyritic andesite, with plagioclase, hornblende and clinopyroxene the most common phenocrysts. Geologists who mapped El Chicho??n in 1980 and 1981 warned that the volcano posed a substantial hazard to the surrounding region. This warning was proven to be prophetic by violent eruptions that occurred in March and April of 1982. These eruptions blasted away nearly all of the summit dome, blanketed the surrounding region with tephra, and sent

  2. Volcano deformation and subdaily GPS products (United States)

    Grapenthin, Ronni

    Volcanic unrest is often accompanied by hours to months of deformation of the ground that is measurable with high-precision GPS. Although GPS receivers are capable of near continuous operation, positions are generally estimated for daily intervals, which I use to infer characteristics of a volcano’s plumbing system. However, GPS based volcano geodesy will not be useful in early warning scenarios unless positions are estimated at high rates and in real time. Visualization and analysis of dynamic and static deformation during the 2011 Tohokuoki earthquake in Japan motivates the application of high-rate GPS from a GPS seismology perspective. I give examples of dynamic seismic signals and their evolution to the final static offset in 30 s and 1 s intervals, which demonstrates the enhancement of subtle rupture dynamics through increased temporal resolution. This stresses the importance of processing data at recording intervals to minimize signal loss. Deformation during the 2009 eruption of Redoubt Volcano, Alaska, suggested net deflation by 0.05 km³ in three distinct phases. Mid-crustal aseismic precursory inflation began in May 2008 and was detected by a single continuous GPS station about 28 km NE of Redoubt. Deflation during the explosive and effusive phases was sourced from a vertical ellipsoidal reservoir at about 7-11.5 km. From this I infer a model for the temporal evolution of a complex plumbing system of at least 2 sources during the eruption. Using subdaily GPS positioning solutions I demonstrate that plumes can be detected and localized by utilizing information on phase residuals. The GPS network at Bezymianny Volcano, Kamchatka, records network wide subsidence at rapid rates between 8 and 12 mm/yr from 2005-2010. I hypothesize this to be caused by continuous deflation of a ˜30 km deep sill under Kluchevskoy Volcano. Interestingly, 1-2 explosive events per year cause little to no deformation at any site other than the summit site closest to the vent. I

  3. Analysis of predictor factors of limb amputation in patients with high-voltage electrical burns

    Directory of Open Access Journals (Sweden)

    Guillermo García Álvarez


    Full Text Available Background: Limb amputation is considered one of the most devastating consequences of electrical injury. Any factors that correlate with the degree of muscle damage can be used to predict the necessity of limb amputation. The aim of this study was to determine the factors that can be used to predict limb amputation in high-voltage electrically injured patients. Methods: Eighty-two high-voltage electrically injured patients were admitted to the Department of Plastic and Reconstructive Surgery and Burns of National Arzobispo Loayza Hospital on a 5 year period. A retrospective analysis of the possible related risk factors between amputation and non-amputation patients was performed. Results: A total of 68 patients were enrolled for analysis. Thirteen patients underwent limb amputations. Multivariate analysis of the risk factors between amputation and non-amputation groups showed statistical significance for first 24 hour creatine kinase-isoenzyme MB (CKMB level. A serum CK-MB level above 14,955 U/L predicted high risk of limb amputation with high specificity (84% and sensitivity (77%. Only one patient with a remarkable decrease of creatine kinase (CPKt and CK-MB levels after fasciotomy avoided a major limb amputation. Conclusion: Our results suggest that CPK-MB level is an independent factor for prediction of limb amputation in patients with high-voltage electrical burns. We suggest that the addition of CPK-MB evaluation to clinical symptom screening may be a valuable method for early detection of muscle damage.

  4. Statistical properties of Joule heating rate, electric field and conductances at high latitudes

    Directory of Open Access Journals (Sweden)

    A. T. Aikio


    Full Text Available Statistical properties of Joule heating rate, electric field and conductances in the high latitude ionosphere are studied by a unique one-month measurement made by the EISCAT incoherent scatter radar in Tromsø (66.6 cgmlat from 6 March to 6 April 2006. The data are from the same season (close to vernal equinox and from similar sunspot conditions (about 1.5 years before the sunspot minimum providing an excellent set of data to study the MLT and Kp dependence of parameters with high temporal and spatial resolution.

    All the parameters show a clear MLT variation, which is different for low and high Kp conditions. Our results indicate that the response of morning sector conductances and conductance ratios to increased magnetic activity is stronger than that of the evening sector. The co-location of Pedersen conductance maximum and electric field maximum in the morning sector produces the largest Joule heating rates 03–05 MLT for Kp≥3. In the evening sector, a smaller maximum occurs at 18 MLT. Minimum Joule heating rates in the nightside are statistically observed at 23 MLT, which is the location of the electric Harang discontinuity.

    An important outcome of the paper are the fitted functions for the Joule heating rate as a function of electric field magnitude, separately for four MLT sectors and two activity levels (Kp<3 and Kp≥3. In addition to the squared electric field, the fit includes a linear term to study the possible anticorrelation or correlation between electric field and conductance. In the midday sector, positive correlation is found as well as in the morning sector for the high activity case. In the midnight and evening sectors, anticorrelation between electric field and conductance is obtained, i.e. high electric fields are associated with low conductances. This is expected to occur in the return current regions adjacent to

  5. Impact of pulsed-electric field and high-voltage electrical discharges on red wine microbial stabilization and quality characteristics. (United States)

    Delsart, C; Grimi, N; Boussetta, N; Miot Sertier, C; Ghidossi, R; Vorobiev, E; Mietton Peuchot, M


    In this study, pulsed-electric fields (PEF) and high-voltage electrical discharges (HVED) are proposed as new techniques for the microbial stabilization of red wines before bottling. The efficiency of the treatment was then evaluated. PEF and HVED-treatments have been applied to wine for the inactivation of Oenococcus oeni CRBO 9304, O. oeni CRBO 0608, Pediococcus parvulus CRBO 2.6 and Brettanomyces bruxellensis CB28. Different treatment times (1, 2, 4, 6, 8 and 10 ms) were used at 20 kV cm(-1) for the PEF treatments and at 40 kV for the HVED treatments, which correspond to applied energies from 80 to 800 kJ l(-1) . The effects of the treatments on the microbial inactivation rate and on various characteristics of red wines (phenolic composition, chromatic characteristics and physico-chemical parameters) were measured. The application of PEF or HVED treatments on red wine allowed the inactivation of alteration yeasts (B. bruxellensis CB28) and bacteria (O. oeni CRBO 9304, O. oeni CRBO 0608 and P. parvulus CRBO 2.6). The electric discharges at 40 kV were less effective than the PEF even after 10 ms of treatments. Indeed, 4 ms of PEF treatment at 20 kV cm(-1) were sufficient to inactivate all micro-organisms present in the wines. Also, the use of PEF had no negative impact on the composition of wines compared to the HVED treatments. Contrary to PEF, the phenolics compounds were degraded after the HVED treatment and the physico-chemical composition of wine were modified with HVED. PEF technology seems to be an interesting alternative to stabilize microbiologically wines before bottling and without modifying their composition. This process offers many advantages for winemakers: no chemical inputs, low energy consumption (320 kJ l(-1) ), fast (treatment time of 4 ms) and athermal (ΔT ≈ 10°C). © 2015 The Society for Applied Microbiology.

  6. Bilateral Lower Limb Amputations in a Nigerian Child Following High-Voltage Electrical Burns Injury: A Case Report


    Dim, EM; Amanari, OC; Nottidge, TE; Inyang, UC; Nwashindi, A


    Abstract The human body conducts electricity very well. Direct contact with electric current can be lethal. The passage of electric current through the body is capable of producing a wide spectrum of injuries, including serious damage to the heart, brain, skin and muscles. Naked high-voltage electric cables negligently abandoned in residential, commercial and industrial areas are a recipe for disaster. This is a case report of a 5-year girl child who had bilateral lower limb gangrene followin...

  7. The Role of Field Electron Emission in Polypropylene/Aluminum Nanodielectrics Under High Electric Fields. (United States)

    Zhang, Guoqiang; Li, Yue; Tang, Saide; Thompson, Rhett D; Zhu, Lei


    Polymer/metallic particle nanocomposites or nanodielectrics can exhibit colossal dielectric constants with a relatively low dissipation factor under low electric fields and thus seem to be promising for high-energy density dielectric capacitors. To study this possibility, this work focused on the dielectric performance and loss mechanisms in polypropylene (PP)/aluminum nanoparticle (nAl NP) composites under high electric fields. Phosphonic acid-terminated poly(ethylene-co-1-butene) was grafted to the Al2O3 surface layer on the nAl NPs in order to achieve reasonable dispersion in the PP matrix. The dielectric breakdown study showed that the breakdown strength decreased to nearly 1/20 that of the neat PP film as the nAl content increased to 25.0 vol %. The leakage current study revealed three electronic conduction mechanisms in the PP/100 nm nAl nanocomposites, namely, ohmic conduction at low fields, hopping conduction at intermediate fields, and Fowler-Nordheim (FN) field electron emission above a critical field, depending on the filler content. Compared to the 100 nm nAl NPs, smaller (e.g., 18 nm) nAl NPs needed a much higher electric field to exhibit FN field electron emission. It was the FN electron tunneling that induced a substantial reduction in breakdown strength for the PP/nAl nanocomposites. Meanwhile, electron-tunneling injected space charges (electrons) from nAl NPs into the PP matrix, and internal electronic conduction led to significant dielectric nonlinearity at high poling fields. Although polymer/metallic NP composites are not suitable for high-field electric applications, they can be good candidates for electrical switches and quantum tunneling composites operated at relatively low electric fields.

  8. A novel high-performance high-frequency SOI MESFET by the damped electric field (United States)

    Orouji, Ali A.; Khayatian, Ahmad; Keshavarzi, Parviz


    In this paper, we introduce a novel silicon-on-insulator (SOI) metal-semiconductor field-effect-transistor (MESFET) using the damped electric field (DEF). The proposed structure is geometrically symmetric and compatible with common SOI CMOS fabrication processes. It has two additional oxide regions under the side gates in order to improve DC and RF characteristics of the DEF structure due to changes in the electrical potential, the electrical field distributions, and rearrangement of the charge carriers. Improvement of device performance is investigated by two-dimensional and two-carrier simulation of fundamental parameters such as breakdown voltage (VBR), drain current (ID), output power density (Pmax), transconductance (gm), gate-drain and gate-source capacitances, cut-off frequency (fT), unilateral power gain (U), current gain (h21), maximum available gain (MAG), and minimum noise figure (Fmin). The results show that proposed structure operates with higher performances in comparison with the similar conventional SOI structure.

  9. Biogeochemical interactions among the arsenic, iron, humic substances, and microbes in mud volcanoes in southern Taiwan. (United States)

    Liu, Chia-Chuan; Maity, Jyoti Prakash; Jean, Jiin-Shuh; Sracek, Ondra; Kar, Sandeep; Li, Zhaohui; Bundschuh, Jochen; Chen, Chien-Yen; Lu, Hsueh-Yu


    Fluid and mud samples collected from Hsiaokunshui (HKS), Wushanting (WST), Yenshuikeng (YSK), Kunshuiping (KSP), Liyushan (LYS), and Sinyangnyuhu (SYNH) mud volcanoes of southwestern Taiwan were characterized for major ions, humic substances (HS) and trace elements concentrations. The relationship between the release of arsenic (As) and activities of sulfate-reducing bacteria has been assessed to understand relevant geochemical processes in the mud volcanoes. Arsenic (0.02-0.06 mg/L) and humic substances (4.13 × 10(-4) to 1.64 × 10(-3) mM) in the fluids of mud volcanoes showed a positive correlation (r = 0.99, p volcano. Arsenic and iron in mud sediments formed two separate groups i) high As, but low Fe in HKS, WST, and SYNH; and ii) low As, but high Fe in the YSK, KSP, and LYS mud volcanoes. The Eh(S.H.E.) values of the mud volcano liquids were characterized by mild to strongly reducing conditions. The HKS, SYNH, and WST mud volcanoes (near the Chishan Fault) belongs to strong reducing environment (-33 to -116 mV), whereas the LYS, YSK, and KSP mud volcanoes located near the coastal plain are under mild reducing environment (-11 to 172 mV). At low Eh values mud volcanoes, saturation index (SI) values of poorly crystalline phases such as amorphous ferric hydroxide indicate understaturation, whereas saturation is reached in relatively high Eh(S.H.E.) values mud volcanoes. Arsenic contents in sediments are low, presumably due to its release to fluids (As/Fe ratio in YSK, KSP, and LYS sediment: 4.86 × 10(-4)-6.20 × 10(-4)). At low Eh(S.H.E.) values (mild to strong reducing environment), arsenic may co-precipitate with sulfides as a consequence of sulfate reduction (As/Fe ratios in WST, HKS, and SYNH sediments: 0.42-0.69).

  10. Development of volcano monitoring technique using repeating earthquakes observed by the Volcano Observation Network of NIED (United States)

    Kohno, Y.; Ueda, H.; Kimura, H.; Nagai, M.; Miyagi, Y.; Fujita, E.; Kozono, T.; Tanada, T.


    After the Grate East Japan Earthquake (M9.0) on March 11, 2011, the M6.4 earthquake occurred beneath Mt. Fuji on March 15, 2011. Although the hypocenter seemed to be very close to an assumed magma chamber of Fuji volcano, no anomalies in volcanic activity have been observed until August 2012. As an example, after the M6.1 earthquake occurred in 1998 at southwest of Iwate volcano, a change of seismic velocity structure (e.g. Nishimura et al., 2000) was observed as well as active seismicity and crustal deformation. It had affected waveforms of repeating earthquakes occurring at a plate subduction zone, that is, the waveform similarities were reduced just after the earthquake due to upwelling of magma. In this study, first we analyzed for Mt. Fuji where such changes are expected by the occurrence of the earthquake to try to develop a tool for monitoring active volcanoes using the Volcano Observation network (V-net) data. We used seismic waveform data of repeating earthquakes observed by short period seismometers of V-net and the High Sensitivity Seismograph Network Japan (Hi-net) stations near Fuji volcano after 2007. The seismic data were recorded with a sampling rate of 100 Hz, and we applied 4-8 Hz band pass filter to reduce noise. The repeating earthquakes occurred at the plate subduction zone and their catalog is compiled by Hi-net data (Kimura et al., 2006). We extracted repeating earthquake groups that include earthquakes before and after the M6.4 earthquake on March 15, 2011. A waveform of the first event of the group and waveforms of the other events are compared and calculated cross-correlation coefficients. We adjusted P wave arrivals of each event and calculate the coefficients and lag times of the latter part of the seismic waves with the time window of 1.25 s. We searched the best fit maximizing the cross-correlation coefficients with 0.1 s shift time at each time window. As a result we found three remarkable points at this time. [1] Comparing lag times

  11. Science at the policy interface: volcano-monitoring technologies and volcanic hazard management (United States)

    Donovan, Amy; Oppenheimer, Clive; Bravo, Michael


    This paper discusses results from a survey of volcanologists carried out on the Volcano Listserv during late 2008 and early 2009. In particular, it examines the status of volcano monitoring technologies and their relative perceived value at persistently and potentially active volcanoes. It also examines the role of different types of knowledge in hazard assessment on active volcanoes, as reported by scientists engaged in this area, and interviewees with experience from the current eruption on Montserrat. Conclusions are drawn about the current state of monitoring and the likely future research directions, and also about the roles of expertise and experience in risk assessment on active volcanoes; while local knowledge is important, it must be balanced with fresh ideas and expertise in a combination of disciplines to produce an advisory context that is conducive to high-level scientific discussion.

  12. Mount Rainier, a decade volcano

    Energy Technology Data Exchange (ETDEWEB)

    Kuehn, S.C.; Hooper, P.R. (Washington State Univ., Pullman, WA (United States). Dept. of Geology); Eggers, A.E. (Univ. of Puget Sound, Tacoma, WA (United States). Dept. of Geology)


    Mount Rainier, recently designated as a decade volcano, is a 14,410 foot landmark which towers over the heavily populated southern Puget Sound Lowland of Washington State. It last erupted in the mid-1800's and is an obvious threat to this area, yet Rainier has received little detailed study. Previous work has divided Rainier into two distinct pre-glacial eruptive episodes and one post-glacial eruptive episode. In a pilot project, the authors analyzed 253 well-located samples from the volcano for 27 major and trace elements. Their objective is to test the value of chemical compositions as a tool in mapping the stratigraphy and understanding the eruptive history of the volcano which they regard as prerequisite to determining the petrogenesis and potential hazard of the volcano. The preliminary data demonstrates that variation between flows is significantly greater than intra-flow variation -- a necessary condition for stratigraphic use. Numerous flows or groups of flows can be distinguished chemically. It is also apparent from the small variation in Zr abundances and considerable variation in such ratios as Ba/Nb that fractional crystallization plays a subordinate role to some form of mixing process in the origin of the Mount Rainier lavas.

  13. Conductor of high electrical current at high temperature in oxygen and liquid metal environment

    Energy Technology Data Exchange (ETDEWEB)

    Powell, IV, Adam Clayton; Pati, Soobhankar; Derezinski, Stephen Joseph; Lau, Garrett; Pal, Uday B.; Guan, Xiaofei; Gopalan, Srikanth


    In one aspect, the present invention is directed to apparatuses for and methods of conducting electrical current in an oxygen and liquid metal environment. In another aspect, the invention relates to methods for production of metals from their oxides comprising providing a cathode in electrical contact with a molten electrolyte, providing a liquid metal anode separated from the cathode and the molten electrolyte by a solid oxygen ion conducting membrane, providing a current collector at the anode, and establishing a potential between the cathode and the anode.

  14. High-temperature nuclear reactor power plant cycle for hydrogen and electricity production – numerical analysis

    Directory of Open Access Journals (Sweden)

    Dudek Michał


    Full Text Available High temperature gas-cooled nuclear reactor (called HTR or HTGR for both electricity generation and hydrogen production is analysed. The HTR reactor because of the relatively high temperature of coolant could be combined with a steam or gas turbine, as well as with the system for heat delivery for high-temperature hydrogen production. However, the current development of HTR’s allows us to consider achievable working temperature up to 750°C. Due to this fact, industrial-scale hydrogen production using copper-chlorine (Cu-Cl thermochemical cycle is considered and compared with high-temperature electrolysis. Presented calculations show and confirm the potential of HTR’s as a future solution for hydrogen production without CO2 emission. Furthermore, integration of a hightemperature nuclear reactor with a combined cycle for electricity and hydrogen production may reach very high efficiency and could possibly lead to a significant decrease of hydrogen production costs.

  15. Electrical conductivity of molten ZnCl{sub 2} at temperature as high as 1421 K

    Energy Technology Data Exchange (ETDEWEB)

    Salyulev, Alexander B.; Potapov, Alexei M. [RAS Ural Branch, Ekaterinburg. (Russian Federation) Institute of High-Temperature Electrochemistry


    The electrical conductivity of molten ZnCl{sub 2} was measured in a wide temperature range (ΔT=863 K) to a temperature as high as 1421 K that is 417 degrees above the boiling point of the salt. At the temperature maximum of the own vapor pressure of the salt reached several megapascals.

  16. A Simple Demonstration of the High-Temperature Electrical Conductivity of Glass (United States)

    Chiaverina, Chris


    We usually think of glass as a good electrical insulator; this, however, is not always the case. There are several ways to show that glass becomes conducting at high temperatures, but the following approach, devised by Brown University demonstration manager Gerald Zani, may be one of the simplest to perform.

  17. A new approach for explanation of specimen rupture under high electric field. (United States)

    Mikhailovskij, I M; Wanderka, N; Storizhko, V E; Ksenofontov, V A; Mazilova, T I


    Failure of needle-shaped specimens under the action of high electric fields is one of the most serious problems in many field-ionization devices and methods. It was shown that the length of what was removed during discharge part of specimens in most of the cases was several orders greater than that of an initial radius of the specimen apex. Experimental results obtained in this work indicate that electrical breakdown in field-ion microscopes is initiated by the impact of nanoparticles detached from a point anode in a high electric field. A new approach for explanation of an observed specimen failure in a high electric field was proposed, where the formation and expansion of the cathode plasma play the key role in the mechanical rupture and melting of field-ion tips. The expanding plasma behaves as a dynamic capacitor plate characterized by a high velocity and increasing field strength at the specimen tip. The field rise rate at a constant voltage in a dynamic plasma-to-tip capacitor is of the order of >10(20)V/m/s. The present experimental data along with the ecton model of the vacuum breakdown allow the results to be discussed as a mechanical sample failure under the action of the superhigh positive field pulse induced by the cathode plasma expansion.

  18. A Simple Demonstration of the High-Temperature Electrical Conductivity of Glass (United States)

    Chiaverina, Chris


    We usually think of glass as a good electrical insulator; this, however, is not always the case. There are several ways to show that glass becomes conducting at high temperatures, but the following approach, devised by Brown University demonstration manager Gerald Zani, may be one of the simplest to perform.

  19. Swiss pumped hydro storage potential for Germany's electricity system under high penetration of intermittent renewable energy

    NARCIS (Netherlands)

    van Meerwijk, Aagje J. H.; Davila-Martinez, Alejandro; Laugs, Gideon A. H.


    In order to cut greenhouse-gas emissions and increase energy security, the European Commission stimulates the deployment of intermittent renewable energy sources (IRES) towards 2050. In an electricity system with high shares of IRES implemented in the network, energy balancing like storage is needed

  20. An Electrical Engineering Summer Academy for Middle School and High School Students (United States)

    LoPresti, Peter G.; Manikas, Theodore W.; Kohlbeck, Jeff G.


    An Electrical Engineering Summer Academy for Pre-College Students was held at the University of Tulsa, Tulsa, OK, during the summers of 2007 and 2008. The Academy participants included students having just completed 7th to 11th grade and teachers from middle school through high school. The students and teachers participated in team-building,…

  1. Neural correlates of heterotopic facilitation induced after high frequency electrical stimulation of nociceptive pathways

    NARCIS (Netherlands)

    Broeke, E.N. van den; Heck, C.H. van; Rijn, C.M. van; Wilder-Smith, O.H.G.


    Background High frequency electrical stimulation (HFS) of primary nociceptive afferents in humans induce a heightened sensitivity in the surrounding non-stimulated skin area. Several studies suggest that this heterotopic effect is the result of central (spinal) plasticity. The aim of this study is t

  2. The effects of high-voltage pulse electric discharges on ion adsorption on activated carbons (United States)

    Gafurov, M. M.; Sveshnikova, D. A.; Larin, S. V.; Rabadanov, K. Sh.; Shabanova, Z. E.; Yusupova, A. A.; Ramazanov, A. Sh.


    The effects of high-voltage pulse electric discharges (HPED) on sorption of boron and sulfate ions on activated carbons of different kinds (KM-2, BAU, DAK) were investigated. The effect of HPED activation on the sorption characteristics of the systems was found to be similar to the temperature effect.

  3. Carbon Nanotube Nanocomposites with Highly Enhanced Strength and Conductivity for Flexible Electric Circuits. (United States)

    Hwang, Ji-Young; Kim, Han-Sem; Kim, Jeong Hun; Shin, Ueon Sang; Lee, Sang-Hoon


    Carbon nanotubes (CNTs) have an important role in nanotechnology due to their unique properties, retaining the inherent material flexibility, superior strength, and electrical conductivity, unless the bottleneck of CNTs persists and the aggregated structure is overcome. Here, we report on the highly enhanced mechanical and electrical properties of the CNT-chitosan nanocomposites through homogeneous dispersion of CNTs into chitosan solution using a high-pressure homogenizer. The optimal condition is a 50% (w/w) chitosan-CNT film, providing about 7 nm thickness of homogeneous chitosan layer on CNTs, a good tensile strength of 51 MPa, high electrical conductivity under 16 Ω/sq, and a stable bending and folding performance. This CNT-chitosan nanocomposite with highly enhanced properties is an amenable material to fabricate structures of various shapes such as films, sensors, and circuits and also enables a simple and cost-effective approach to improve the performance of a device that presents the first flexible and soft electric circuits yet reported using only CNT-chitosan as the conductor.

  4. Swiss pumped hydro storage potential for Germany's electricity system under high penetration of intermittent renewable energy

    NARCIS (Netherlands)

    van Meerwijk, Aagje J. H.; Davila-Martinez, Alejandro; Laugs, Gideon A. H.


    In order to cut greenhouse-gas emissions and increase energy security, the European Commission stimulates the deployment of intermittent renewable energy sources (IRES) towards 2050. In an electricity system with high shares of IRES implemented in the network, energy balancing like storage is needed

  5. Effect of a low voltage with a high frequency electrical stunning on unconsciousness in slaughter pigs

    NARCIS (Netherlands)

    Lambooij, B.; Merkus, G.S.M.; Voorst, van N.; Pieterse, C.


    Effects of low voltage and high frequency electrical stunning of slaughter pigs was examined. Forty slaughter pigs were positioned for stunning while lying on a beam in a cage and stunned with 240 V with 800 Hz during 3 s passing the brain and 125 V with 50 Hz during 3 s passing the heart. Before th

  6. Electric Vehicles for Improved Operation of Power Systems with High Wind Power Penetration

    DEFF Research Database (Denmark)

    Larsen, Esben; Chandrashekhara, Divya K; Østergaard, Jacob


    In a power system with a high share of wind energy the wind fluctuation causes a variation in the power generation, which must be compensated from other sources. The situation in Denmark with a penetration of more than 20% wind in yearly average is presented. The introduction of electric drive ve...

  7. Fiber Bragg grating strain sensors to monitor and study active volcanoes (United States)

    Sorrentino, Fiodor; Beverini, Nicolò; Carbone, Daniele; Carelli, Giorgio; Francesconi, Francesco; Gambino, Salvo; Giacomelli, Umberto; Grassi, Renzo; Maccioni, Enrico; Morganti, Mauro


    Stress and strain changes are among the best indicators of impending volcanic activity. In volcano geodesy, borehole volumetric strain-meters are mostly utilized. However, they are not easy to install and involve high implementation costs. Advancements in opto-electronics have allowed the development of low-cost sensors, reliable, rugged and compact, thus particularly suitable for field application. In the framework of the EC FP7 MED-SUV project, we have developed strain sensors based on the fiber Bragg grating (FBG) technology. In comparison with previous implementation of the FBG technology to study rock deformations, we have designed a system that is expected to offer a significantly higher resolution and accuracy in static measurements and a smooth dynamic response up to 100 Hz, implying the possibility to observe seismic waves. The system performances are tailored to suit the requirements of volcano monitoring, with special attention to power consumption and to the trade-off between performance and cost. Preliminary field campaigns were carried out on Mt. Etna (Italy) using a prototypal single-axis FBG strain sensor, to check the system performances in out-of-the-lab conditions and in the harsh volcanic environment (lack of mains electricity for power, strong diurnal temperature changes, strong wind, erosive ash, snow and ice during the winter time). We also designed and built a FBG strain sensor featuring a multi-axial configuration which was tested and calibrated in the laboratory. This instrument is suitable for borehole installation and will be tested on Etna soon.

  8. Geomagnetism, volcanoes, global climate change, and predictability. A progress report

    Directory of Open Access Journals (Sweden)

    G. P. Gregori


    Full Text Available A model is investigated, by which the encounters of the solar system with dense interstellar clouds ought to trigger either geomagnetic field reversals or excursions, that produce extra electric currents within the Earth dynamo, that cause extra Joule's heating, that supplies volcanoes and endogenous processes. Volcanoes increase the Earth degassing into the atmosphere, hence the concentration of the minor atmospheric constituents, including the greenhouse gases, hence they affect climate temperature, glacier melting, sea level and global change. This investigation implies both theoretical studies and observational data handling on different time scales, including present day phenomena, instrumental data series, historical records, proxy data, and geological and palaeontological evidences. The state of the art is briefly outlined, mentioning some already completed achievements, investigations in progress, and future perspectives.

  9. High field electrical behaviour in lithium–phospho–vanadate glass system

    Indian Academy of Sciences (India)

    C Narayana Reddy; S Asokan; R V Anavekar


    The high field electrical switching behaviour of lithium–phospho–vanadate glasses has been studied by determining the current–voltage characteristics. The investigated glasses exhibit temperature, thickness and composition dependent trends. At low current, the – characteristics obey Ohm’s law followed by a negative resistance region where the bulk behaviour dominates and at higher values of current the sample goes to a low resistance state. The studied glasses exhibit memory type switching. It is suggested that electrical switching is due to the formation of conducting channels that are due to electronic origin while thermal effects dominate once the channels are formed resulting in crystallization.

  10. Computation for High Excited Stark Levels of hydrogen Atoms in Uniform Electric Fields

    Institute of Scientific and Technical Information of China (English)



    We present a new method for the numerical calculation of exact complex eigenvalues of Schrodinger equations for a hydrogen atom in a uniform electric field. This method allows a direct calculation for complex eigenvalues without using any auxiliary treatment, such as the Breit-Wigner parametrization and the complex scale transformation,etc. The characteristics of high excited atoms in electric field have attracted extensive interest in experimental aspect, however, the existing theoretical calculation is only up to n = 40. Here we present the computation results ranging from n = 1 to 100. The data for n(<,_ ) 40 are in agreement with the results of other researchers.

  11. Microfluidic Impedance Flow Cytometry Enabling High-Throughput Single-Cell Electrical Property Characterization

    Directory of Open Access Journals (Sweden)

    Jian Chen


    Full Text Available This article reviews recent developments in microfluidic impedance flow cytometry for high-throughput electrical property characterization of single cells. Four major perspectives of microfluidic impedance flow cytometry for single-cell characterization are included in this review: (1 early developments of microfluidic impedance flow cytometry for single-cell electrical property characterization; (2 microfluidic impedance flow cytometry with enhanced sensitivity; (3 microfluidic impedance and optical flow cytometry for single-cell analysis and (4 integrated point of care system based on microfluidic impedance flow cytometry. We examine the advantages and limitations of each technique and discuss future research opportunities from the perspectives of both technical innovation and clinical applications.

  12. Microfluidic impedance flow cytometry enabling high-throughput single-cell electrical property characterization. (United States)

    Chen, Jian; Xue, Chengcheng; Zhao, Yang; Chen, Deyong; Wu, Min-Hsien; Wang, Junbo


    This article reviews recent developments in microfluidic impedance flow cytometry for high-throughput electrical property characterization of single cells. Four major perspectives of microfluidic impedance flow cytometry for single-cell characterization are included in this review: (1) early developments of microfluidic impedance flow cytometry for single-cell electrical property characterization; (2) microfluidic impedance flow cytometry with enhanced sensitivity; (3) microfluidic impedance and optical flow cytometry for single-cell analysis and (4) integrated point of care system based on microfluidic impedance flow cytometry. We examine the advantages and limitations of each technique and discuss future research opportunities from the perspectives of both technical innovation and clinical applications.

  13. High Power MPD Nuclear Electric Propulsion (NEP) for Artificial Gravity HOPE Missions to Callisto (United States)

    McGuire, Melissa L.; Borowski, Stanley K.; Mason, Lee M.; Gilland, James


    This documents the results of a one-year multi-center NASA study on the prospect of sending humans to Jupiter's moon, Callisto, using an all Nuclear Electric Propulsion (NEP) space transportation system architecture with magnetoplasmadynamic (MPD) thrusters. The fission reactor system utilizes high temperature uranium dioxide (UO2) in tungsten (W) metal matrix cermet fuel and electricity is generated using advanced dynamic Brayton power conversion technology. The mission timeframe assumes on-going human Moon and Mars missions and existing space infrastructure to support launch of cargo and crewed spacecraft to Jupiter in 2041 and 2045, respectively.

  14. Dynamic observations of the 8 January 2010 pyroclastic flow from the Soufriere Hills Volcano, Montserrat ascertained by high-definition and FLIR video analysis, as well as geometric analysis of the DEM (United States)

    Molle, A.; Ogburn, S. E.; Calder, E. S.; Roche, O.; Harris, A. J.


    On January 8th 2010, Soufriere Hills Volcano (Montserrat) experienced a collapse of the northwestern part of its andesitic lava dome. The ensuing explosive event lead to a 8.3 km high eruption column and generated a pyroclastic density current (PDC) that propagated down the northern flank of the volcano, moving down the Belham valley. This PDC was recorded from the Montserrat Volcano Observatory using both normal High- Definition and Forward Looking Infrared (FLIR) video cameras. The flow front velocity profile, plus the vertical motion of discrete buoyant thermals ascending above the PDC, were measured by combining the video data with a deposit map and a high spatial-resolution DEM. A theoretical treatment was then applied to extract key parameters that describe the buoyant motion of thermals ascending above the current (including density, particle mass volume fraction, and temperature). Interaction of the PDC with topographic features corresponded to important changes in the dynamics of the PDC as well as the ascent of the buoyant ash-clouds These interactions included an increase of the ascent rate of buoyant thermals when the PDC encountered topographic barriers, and deceleration of the flow front velocity due of high degrees of valley sinuosity. Additionally, a major change in flow dynamics was visible in our data 2 - 3 km from the dome. To investigate this further, channel slope, sinuosity, and cross-sectional area were measured from high-resolution DEMs using GIS software; and were compared to geometric parameters of the mapped ash-cloud surge deposits. The data illustrate three surge generation regimes: a proximal area of rapid lateral expansion; a medial deflation zone; and a steadier distal surge 'fringe'. These surge regimes relate directly the dramatic change in buoyant thermal flow dynamics observed 2-3 km from the dome and are also correlated with velocity and inversely correlated with valley cross-sectional area. Several possible origins can be

  15. Lahar Hazard Modeling at Tungurahua Volcano, Ecuador (United States)

    Sorensen, O. E.; Rose, W. I.; Jaya, D.


    lahar-hazard-zones using a digital elevation model (DEM), was used to construct a hazard map for the volcano. The 10 meter resolution DEM was constructed for Tungurahua Volcano using scanned topographic lines obtained from the GIS Department at the Escuela Politécnica Nacional, Quito, Ecuador. The steep topographic gradients and rapid downcutting of most rivers draining the edifice prevents the deposition of lahars on the lower flanks of Tungurahua. Modeling confirms the high degree of flow channelization in the deep Tungurahua canyons. Inundation zones observed and shown by LAHARZ at Baños yield identification of safe zones within the city which would provide safety from even the largest magnitude lahar expected.

  16. Mineralogical and geochemical study of mud volcanoes in north ...

    African Journals Online (AJOL)


    Key word: Mud volcano, clay mineralogy, geochemistry, mud breccias, North Moroccan Atlantic margin. INTRODUCTION .... The geochemical analysis of the metals shows a high Ti ..... smectite evolved into an illite, or because the initial source is not .... Pinheiro LM, Kopf A, Boetius A (2006): Microbial methane turnover at.

  17. Exposure to electromagnetic fields aboard high-speed electric multiple unit trains. (United States)

    Niu, D; Zhu, F; Qiu, R; Niu, Q


    High-speed electric multiple unit (EMU) trains generate high-frequency electric fields, low-frequency magnetic fields, and high-frequency wideband electromagnetic emissions when running. Potential human health concerns arise because the electromagnetic disturbances are transmitted mainly into the car body from windows, and from there to passengers and train staff. The transmission amount and amplitude distribution characteristics that dominate electromagnetic field emission need to be studied, and the exposure level of electromagnetic field emission to humans should be measured. We conducted a series of tests of the on board electromagnetic field distribution on several high-speed railway lines. While results showed that exposure was within permitted levels, the possibility of long-term health effects should be investigated.

  18. Significant improvement in Mn2O3 transition metal oxide electrical conductivity via high pressure (United States)

    Hong, Fang; Yue, Binbin; Hirao, Naohisa; Liu, Zhenxian; Chen, Bin


    Highly efficient energy storage is in high demand for next-generation clean energy applications. As a promising energy storage material, the application of Mn2O3 is limited due to its poor electrical conductivity. Here, high-pressure techniques enhanced the electrical conductivity of Mn2O3 significantly. In situ synchrotron micro X-Ray diffraction, Raman spectroscopy and resistivity measurement revealed that resistivity decreased with pressure and dramatically dropped near the phase transition. At the highest pressure, resistivity reduced by five orders of magnitude and the sample showed metal-like behavior. More importantly, resistivity remained much lower than its original value, even when the pressure was fully released. This work provides a new method to enhance the electronic properties of Mn2O3 using high-pressure treatment, benefiting its applications in energy-related fields. PMID:28276479

  19. High-Lift Propeller System Configuration Selection for NASA's SCEPTOR Distributed Electric Propulsion Flight Demonstrator (United States)

    Patterson, Michael D.; Derlaga, Joseph M.; Borer, Nicholas K.


    Although the primary function of propellers is typically to produce thrust, aircraft equipped with distributed electric propulsion (DEP) may utilize propellers whose main purpose is to act as a form of high-lift device. These \\high-lift propellers" can be placed upstream of wing such that, when the higher-velocity ow in the propellers' slipstreams interacts with the wing, the lift is increased. This technique is a main design feature of a new NASA advanced design project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR). The goal of the SCEPTOR project is design, build, and y a DEP aircraft to demonstrate that such an aircraft can be much more ecient than conventional designs. This paper provides details into the high-lift propeller system con guration selection for the SCEPTOR ight demonstrator. The methods used in the high-lift propeller system conceptual design and the tradeo s considered in selecting the number of propellers are discussed.

  20. High precision electric gate for time-of-flight ion mass spectrometers (United States)

    Sittler, Edward C. (Inventor)


    A time-of-flight mass spectrometer having a chamber with electrodes to generate an electric field in the chamber and electric gating for allowing ions with a predetermined mass and velocity into the electric field. The design uses a row of very thin parallel aligned wires that are pulsed in sequence so the ion can pass through the gap of two parallel plates, which are biased to prevent passage of the ion. This design by itself can provide a high mass resolution capability and a very precise start pulse for an ion mass spectrometer. Furthermore, the ion will only pass through the chamber if it is within a wire diameter of the first wire when it is pulsed and has the right speed so it is near all other wires when they are pulsed.

  1. Electrical and structural R&D activities on high voltage dc solid insulator in vacuum

    Energy Technology Data Exchange (ETDEWEB)

    Pilan, N., E-mail: [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Marcuzzi, D.; Rizzolo, A.; Grando, L.; Gambetta, G. [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Rosa, S. Dalla [Umicore – Italbras S.p.A., Strada del Balsego, n.6, 36100 Vicenza (Italy); Kraemer, V.; Quirmbach, T. [FRIATEC Ceramics Division, Steinzeugstrasse 50, 68229 Mannheim (Germany); Chitarin, G. [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Gobbo, R.; Pesavento, G. [DII, Università di Padova, v. Gradenigo 6/A, I-35131 Padova (Italy); De Lorenzi, A.; Lotto, L.; Rizzieri, R.; Fincato, M.; Romanato, L.; Trevisan, L.; Cervaro, V.; Franchin, L. [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy)


    Highlights: • A thorough R&D activity on the MITICA post insulator prototypes is being carried out. • The design has been numerically verified considering both mechanical and electrical aspects. • Experimental validation has been started, with positive results in both involved fields. • Alternative design solutions thickness have been proposed and successfully tested. - Abstract: This paper describes the R&D work performed in support of the design of the alumina insulators for the MITICA Neutral Beam Injector. The ceramic insulators are critical elements, both from the structural and electrical point of view, of the 1 MV electrostatic accelerator of the MITICA injector, as they are required to sustain both the mechanical loads due to the cantilevered weight of the ion source and the high electric field between the accelerator grids. This paper presents the results of numerical simulations and experimental tests on prototypes that have been carried out to validate the insulator design under realistic operating conditions.

  2. Proposal of the Electrically Charged Stellar Black Holes as Accelerators of Ultra High Energy Cosmic Rays

    CERN Document Server

    Soto-Manriquez, Jose


    A new mechanism for the acceleration of ultra high energy cosmic rays (UHECR) is presented here. It is based on the tunnel-ionization of neutral atoms approaching electrically charged stellar black holes and on the repulsion of the resulting positively charged atomic part by huge, long-range electric fields. Energies above $10^{18}$ eV for these particles are calculated in a simple way by means of this single-shot, all-electrical model. When this acceleration mechanism is combined with the supernova explosions in the galactic halo of the massive runaway stars expelled from the galactic disk, this model predicts nearly the correct values of the measured top energy of the UHECRs and their flux in a specified EeV energy range. It also explains the near isotropy of the arrivals of these energetic particles to Earth, as has been recently measured by the Auger Observatory.

  3. High resistance to sulfur poisoning of Ni with copper skin under electric field (United States)

    Xu, Xiaopei; Zhang, Yanxing; Yang, Zongxian


    The effects of sulfur poisoning on the (1 0 0), (1 1 0) and (1 1 1) surfaces of pure Ni and Cu/Ni alloy are studied in consideration of the effect of electric field. The effects of Cu dopants on the S poisoning characteristics are analyzed by the means of the density functional theory results in combination with thermodynamics data using the ab initio atomistic thermodynamic method. When the Cu concentration increases to 50% on the surface layer of the Cu/Ni alloy, the (1 1 0) surface becomes the most vulnerable to the sulfur poisoning. Ni with a copper skin can mostly decrease the sulfur poisoning effect. Especially under the electric field of 1.0 V/Å, the sulfur adsorption and phase transition temperature can be further reduced. We therefore propose that Ni surfaces with copper skin can be very effective to improve the resistance to sulfur poisoning of the Ni anode under high electric field.

  4. Permeabilization of yeast Saccharomyces cerevisiae cell walls using nanosecond high power electrical pulses (United States)

    Stirke, A.; Zimkus, A.; Balevicius, S.; Stankevic, V.; Ramanaviciene, A.; Ramanavicius, A.; Zurauskiene, N.


    The electrical field-induced changes of the yeast Saccharomyces cerevisiae cells permeabilization to tetraphenylphosphonium (TPP+) ions were studied using square-shaped, nanosecond duration high power electrical pulses. It was obtained that pulses having durations ranging from 10 ns to 60 ns, and generating electric field strengths up to 190 kV/cm significantly (up to 65 times) increase the absorption rate of TPP+ ions without any detectible influence on the yeast cell viability. The modelling of the TPP+ absorption process using a second order rate equation demonstrates that depending on the duration of the pulses, yeast cell clusters of different sizes are homogeniously permeabilized. It was concluded, that nanosecond pulse-induced permeabilization can be applied to increase the operational speed of whole cell biosensors.

  5. Dissipation of Electrical Energy in Submerged Arc Furnaces Producing Silicomanganese and High-Carbon Ferromanganese (United States)

    Steenkamp, Joalet Dalene; Hockaday, Christopher James; Gous, Johan Petrus; Nzima, Thabo Witness


    Submerged-arc furnace technology is applied in the primary production of ferroalloys. Electrical energy is dissipated to the process via a combination of arcing and resistive heating. In processes where a crater forms between the charge zone and the reaction zone, electrical energy is dissipated mainly through arcing, e.g., in coke-bed based processes, through resistive heating. Plant-based measurements from a device called "Arcmon" indicated that in silicomanganese (SiMn) production, at times up to 15% of the electrical energy used is transferred by arcing, 30% in high-carbon ferromanganese (HCFeMn) production, compared with 5% in ferrochromium and 60% in ferrosilicon production. On average, the arcing is much less at 3% in SiMn and 5% in HCFeMn production.

  6. Skin-effect down hole electric heater for heavy oil and high wax content oil applications

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Chenglin; Wang, Hui; Liu, Yanhua [Liaoning Huafu Petroleum High-Tech Co., Ltd. (China); Xiao, Jon H; Klotz, Eric [ANDMIR Environmental Group Canada Inc. (Canada)


    With the increased production of oil and the depletion of conventional reserves, operators have started to exploit heavy oil and high wax content oil. Adequate production of such oils is difficult to achieve due to viscosity increase and mobility decrease during lifting as a result of heat loss. The down-hole electric heater has been developed to resolve these issues with the application of skin-effect electric heating technology. The aim of this paper is to present how this technology improves the production of heavy oil and waxy oil. Applications of the technology to wells in Chinese oilfields are studied. Results proved the technology to be efficient while being based on a simple process and operating in an easy and safe manner. This paper showed that the down-hole electric heater is a breakthrough technology, resolving the issues encountered in the heavy oil and waxy oil exploitation field, with broad application prospects.

  7. Interactive Volcano Studies and Education Using Virtual Globes (United States)

    Dehn, J.; Bailey, J. E.; Webley, P.


    Internet-based virtual globe programs such as Google Earth provide a spatial context for visualization of monitoring and geophysical data sets. At the Alaska Volcano Observatory, Google Earth is being used to integrate satellite imagery, modeling of volcanic eruption clouds and seismic data sets to build new monitoring and reporting tools. However, one of the most useful information sources for environmental monitoring is under utilized. Local populations, who have lived near volcanoes for decades are perhaps one of the best gauges for changes in activity. Much of the history of the volcanoes is only recorded through local legend. By utilizing the high level of internet connectivity in Alaska, and the interest of secondary education in environmental science and monitoring, it is proposed to build a network of observation nodes around local schools in Alaska and along the Aleutian Chain. A series of interactive web pages with observations on a volcano's condition, be it glow at night, puffs of ash, discolored snow, earthquakes, sounds, and even current weather conditions can be recorded, and the users will be able to see their reports in near real time. The database will create a KMZ file on the fly for upload into the virtual globe software. Past observations and legends could be entered to help put a volcano's long-term activity in perspective. Beyond the benefit to researchers and emergency managers, students and teachers in the rural areas will be involved in volcano monitoring, and gain an understanding of the processes and hazard mitigation efforts in their community. K-12 students will be exposed to the science, and encouraged to participate in projects at the university. Infrastructure at the university can be used by local teachers to augment their science programs, hopefully encouraging students to continue their education at the university level.

  8. Schoolyard Volcanoes: A Unit in Volcanology and Hazards (United States)

    Lechner, H. N.; Gochis, E. E.; Brill, K. A.


    How do you teach volcanology and volcanic hazards to students when there is no volcano nearby? You bring the volcano to them! At Michigan Technological University we have developed a four-lesson-unit for middle and high school students which incorporates virtual, analogue and numerical models to increase students' interests in geosciences while simultaneously expanding the community of earth-science-literate individuals necessary for a disaster resilient society. The unit aims to build on students' prior geoscience knowledge by examining the physical properties that influence volcanic eruptions and introduces them to challenges and methods of communicating hazards and risk. Lesson one engages students in a series of hands-on investigations that explore the "3-Vs" of volcanology: Viscosity, Volatiles and Volume. The students learn about the relationship between magma composition and viscosity and the influence on eruption style, behavior and morphology of different volcanoes. Lesson two uses an analogue model of a volcano to demonstrate the forces involved in an explosive eruption and associated hazards. Students think critically about the factors that affect hazards and risk as well as the variables (such as topography) that affect the eruption and the hazard. During lesson three students use Google Earth for a virtual field trip to Pacaya volcano, Guatemala to examine changes in the landscape over time and other evidence of volcanic activity to make interpretations about the volcano. The final lesson has the students use numerical models and GIS to create hazard maps based on probabilistic lahar scenarios. Throughout the unit students are engaged in an inquiry-based exploration that covers several Next Generation Science Standards (NGSS) content and practices. This four lesson unit has been field tested in two school districts and during a summer engineering program. Results from student work and post-surveys show that this strategy raises interests in and

  9. Improved Electrical Insulation of Rare Earth Permanent Magnetic Materials With High Magnetic Properties

    Institute of Scientific and Technical Information of China (English)

    CHANG Ying; WANG Da-peng; LI Wei; PAN Wei; YU Xiao-jun; QI Min


    Rare earth permanent magnetic materials are typical electrical conductor, and their magnetic properties will decrease because of the eddy current effect, so it is difficult to keep them stable for a long enough time under a high frequency AC field. In the present study, as far as rare earth permanent magnets are concerned, for the first time, rare earth permanent magnets with strong electrical insulation and high magnetic performance have been obtained through experiments, and their properties are as follows:(1) Sm2TM17: Br=0.62 T, jHc=803.7 kA/m, (BH)m= The magnetic properties of Sm2TM17 and NdFeB are obviously higher than those of ferrite permanent magnet, and the electric insulating characteristics of Sm2TM17 and NdFeB applied have in fact been approximately the same as those of ferrite. Therefore, Sm2TM17 and NdFeB will possess the ability to take the place of ferrite under a certain high frequency AC electric field.

  10. High electrical conductivity in out of plane direction of electrodeposited Bi2Te3 films

    Directory of Open Access Journals (Sweden)

    Miguel Muñoz Rojo


    Full Text Available The out of plane electrical conductivity of highly anisotropic Bi2Te3 films grown via electro-deposition process was determined using four probe current-voltage measurements performed on 4.6 - 7.2 μm thickness Bi2Te3 mesa structures with 80 - 120 μm diameters sandwiched between metallic film electrodes. A three-dimensional finite element model was used to predict the electric field distribution in the measured structures and take into account the non-uniform distribution of the current in the electrodes in the vicinity of the probes. The finite-element modeling shows that significant errors could arise in the measured film electrical conductivity if simpler one-dimensional models are employed. A high electrical conductivity of (3.2 ± 0.4 ⋅ 105 S/m is reported along the out of plane direction for Bi2Te3 films highly oriented in the [1 1 0] direction.

  11. Investigation of transient temperature's influence on damage of high-speed sliding electrical contact rail surface (United States)

    Zhang, Yuyan; Sun, Shasha; Guo, Quanli; Yang, Degong; Sun, Dongtao


    In the high speed sliding electrical contact with large current, the temperature of contact area rises quickly under the coupling action of the friction heating, the Joule heating and electric arc heating. The rising temperature seriously affects the conductivity of the components and the yield strength of materials, as well affects the contact state and lead to damage, so as to shorten the service life of the contact elements. Therefore, there is vital significance to measure the temperature accurately and investigate the temperature effect on damage of rail surface. Aiming at the problem of components damage in high speed sliding electrical contact, the transient heat effect on the contact surface was explored and its influence and regularity on the sliding components damage was obtained. A kind of real-time temperature measurement method on rail surface of high speed sliding electrical contact is proposed. Under the condition of 2.5 kA current load, based on the principle of infrared radiation non-contact temperature sensor was used to measure the rail temperature. The dynamic distribution of temperature field was obtained through the simulation analysis, further, the connection between temperature changes and the rail surface damage morphology, the damage volume was analyzed and established. Finally, the method to reduce rail damage and improve the life of components by changing the temperature field was discussed.

  12. Dynamic Range Enhancement of High-Speed Electrical Signal Data via Non-Linear Compression (United States)

    Laun, Matthew C. (Inventor)


    Systems and methods for high-speed compression of dynamic electrical signal waveforms to extend the measuring capabilities of conventional measuring devices such as oscilloscopes and high-speed data acquisition systems are discussed. Transfer function components and algorithmic transfer functions can be used to accurately measure signals that are within the frequency bandwidth but beyond the voltage range and voltage resolution capabilities of the measuring device.

  13. New high-speed line Nuremberg - Ingolstadt - Electrical engineering equipment; Neubaustrecke (NBS) Nuernberg - Ingolstadt - Technische Ausruestung

    Energy Technology Data Exchange (ETDEWEB)

    Krems, S. [Balfour Beatty Rail GmbH, Berlin (Germany); Matthes, U. [DB Projektbau GmbH, Nuernberg (Germany)


    The Bavarian fast railway line Nuremberg - Ingolstadt is equipped with most recent railway infrastructure for a 300 km/h fast high-speed traffic. The electrical engineering installations were implemented within a seven years period. Since December 2006 the line has been integrated into scheduled services and operated with high-speed trains. So far, the installations complied fully with all the requirements. (orig.)

  14. The origin of high-Mg magmas in Mt Shasta and Medicine Lake volcanoes, Cascade Arc (California): higher and lower than mantle oxygen isotope signatures attributed to current and past subduction (United States)

    Martin, E.; Bindeman, I.; Grove, T. L.


    We report the oxygen isotope composition of olivine and orthopyroxene phenocrysts in lavas from the main magma types at Mt Shasta and Medicine Lake Volcanoes: primitive high-alumina olivine tholeiite (HAOT), basaltic andesites (BA), primitive magnesian andesites (PMA), and dacites. The most primitive HAOT (MgO > 9 wt%) from Mt. Shasta has olivine δ18O (δ18OOl) values of 5.9-6.1‰, which are about 1‰ higher than those observed in olivine from normal mantle-derived magmas. In contrast, HAOT lavas from Medicine Lake have δ18OOl values ranging from 4.7 to 5.5‰, which are similar to or lower than values for olivine in equilibrium with mantle-derived magmas. Other magma types from both volcanoes show intermediate δ18OOl values. The oxygen isotope composition of the most magnesian lavas cannot be explained by crustal contamination and the trace element composition of olivine phenocrysts precludes a pyroxenitic mantle source. Therefore, the high and variable δ18OOl signature of the most magnesian samples studied (HAOT and BA) comes from the peridotitic mantle wedge itself. As HAOT magma is generated by anhydrous adiabatic partial melting of the shallow mantle, its 1.4‰ range in δ18OOl reflects a heterogeneous composition of the shallow mantle source that has been influenced by subduction fluids and/or melts sometime in the past. Magmas generated in the mantle wedge by flux melting due to modern subduction fluids, as exemplified by BA and probably PMA, display more homogeneous composition with only 0.5‰ variation. The high-δ18O values observed in magnesian lavas, and principally in the HAOT, are difficult to explain by a single-stage flux-melting process in the mantle wedge above the modern subduction zone and require a mantle source enriched in 18O. It is here explained by flow of older, pre-enriched portions of the mantle through the slab window beneath the South Cascades.

  15. New Free Electron Wire for Loss Free Utilization of Electrical Energy and Highly Energy Efficient Electrical Appliances

    Directory of Open Access Journals (Sweden)

    Sabyasachi Haldar


    Full Text Available New Free Electrons Wire will enable the use of electrical energy and also energy in various other forms, in a loss free way, at room temperature. Free Electrons confined in vacuum at the order of 10-4 torr or more, at the core of the wire, can move a distance as long as about, to a few kilometers without any collision. The vacuum is maintained in a tube made up of alternate layers of Teflon and Silicon Oxynitride. The columbic repulsion between these free electrons will actually conduct energy without any loss. The free electrons trapped in vacuum tube, should be at a particular density of around 2.02 x 108 electrons per unit area. A metal encapsulation(s over the wire is there to keep the electromagnetic field remain confined within the free electron wire, to make it harmless to the health of living creatures. Apart from loss free energy transportation, the free electron wire is also capable of generating very high electromagnetic field due to the free electrons, simply by removing the metal encapsulation(s, which can be used for various purposes. The materials and techniques adopted will make New Free Electron Wire producible commercially, at the cost of general copper wires.

  16. Seismicity at Fuego, Pacaya, Izalco, and San Cristobal Volcanoes, Central America, 1973-1974 (United States)

    McNutt, S.R.; Harlow, D.H.


    Seismic data collected at four volcanoes in Central America during 1973 and 1974 indicate three sources of seismicity: regional earthquakes with hypocentral distances greater than 80 km, earthquakes within 40 km of each volcano, and seismic activity originating at the volcanoes due to eruptive processes. Regional earthquakes generated by the underthrusting and subduction of the Cocos Plate beneath the Caribbean Plate are the most prominent seismic feature in Central America. Earthquakes in the vicinity of the volcanoes occur on faults that appear to be related to volcano formation. Faulting near Fuego and Pacaya volcanoes in Guatemala is more complex due to motion on a major E-W striking transform plate boundary 40 km north of the volcanoes. Volcanic activity produces different kinds of seismic signatures. Shallow tectonic or A-type events originate on nearby faults and occur both singly and in swarms. There are typically from 0 to 6 A-type events per day with b value of about 1.3. At very shallow depths beneath Pacaya, Izalco, and San Cristobal large numbers of low-frequency or B-type events are recorded with predominant frequencies between 2.5 and 4.5 Hz and with b values of 1.7 to 2.9. The relative number of B-type events appears to be related to the eruptive states of the volcanoes; the more active volcanoes have higher levels of seismicity. At Fuego Volcano, however, low-frequency events have unusually long codas and appear to be similar to tremor. High-amplitude volcanic tremor is recorded at Fuego, Pacaya, and San Cristobal during eruptive periods. Large explosion earthquakes at Fuego are well recorded at five stations and yield information on near-surface seismic wave velocities (??=3.0??0.2 km/sec.). ?? 1983 Intern. Association of Volcanology and Chemistry of the Earth's Interior.

  17. Identifying hazard parameter to develop quantitative and dynamic hazard map of an active volcano in Indonesia (United States)

    Suminar, Wulan; Saepuloh, Asep; Meilano, Irwan


    Analysis of hazard assessment to active volcanoes is crucial for risk management. The hazard map of volcano provides information to decision makers and communities before, during, and after volcanic crisis. The rapid and accurate hazard assessment, especially to an active volcano is necessary to be developed for better mitigation on the time of volcanic crises in Indonesia. In this paper, we identified the hazard parameters to develop quantitative and dynamic hazard map of an active volcano. The Guntur volcano in Garut Region, West Java, Indonesia was selected as study area due population are resided adjacent to active volcanoes. The development of infrastructures, especially related to tourism at the eastern flank from the Summit, are growing rapidly. The remote sensing and field investigation approaches were used to obtain hazard parameters spatially. We developed a quantitative and dynamic algorithm to map spatially hazard potential of volcano based on index overlay technique. There were identified five volcano hazard parameters based on Landsat 8 and ASTER imageries: volcanic products including pyroclastic fallout, pyroclastic flows, lava and lahar, slope topography, surface brightness temperature, and vegetation density. Following this proposed technique, the hazard parameters were extracted, indexed, and calculated to produce spatial hazard values at and around Guntur Volcano. Based on this method, the hazard potential of low vegetation density is higher than high vegetation density. Furthermore, the slope topography, surface brightness temperature, and fragmental volcanic product such as pyroclastics influenced to the spatial hazard value significantly. Further study to this proposed approach will be aimed for effective and efficient analyses of volcano risk assessment.

  18. Effect of heat treatments on the tensile and electrical properties of high-strength, high-conductivity copper alloys

    Energy Technology Data Exchange (ETDEWEB)

    Zinkle, S.J.; Eatherly, W.S. [Oak Ridge National Lab., TN (United States)


    The unirradiated tensile properties of CuCrZr produced by two different vendors have been measured following different heat treatments. Room temperature electrical resistivity measurements were also performed in order to estimate the thermal conductivity of these specimens. The thermomechanical conditions studied included solution quenched, solution quenched and aged (ITER reference heat treatment), simulated slow HIP thermal cycle ({approximately}1{degrees}C/min cooling from solutionizing temperature) and simulated fast HIP thermal cycle ({approximately}100{degrees}C/min cooling from solutionizing temperature). Specimens from the last two heat treatments were tested in both the solution-cooled condition and after subsequent precipitate aging at 475{degrees}C for 2 h. Both of the simulated HIP thermal cycles caused a pronounced decreases in the strength and electrical conductivity of CuCrZr. The tensile and electrical properties were unchanged by subsequent aging in the slow HIP thermal cycles caused a pronounced decrease in the strength and electrical conductivity of CuCrZr. The tensile and electrical properties were unchanged by subsequent aging in the slow HIP thermal cycle specimens, whereas the strength and conductivity following aging in the fast HIP thermal cycle improved to {approximately}65% of the solution quenched and aged CuCrZr values. Limited tensile and electrical resistivity measurements were also made on two new heats of Hycon 3HP CuNiBe. High strength but poor uniform and total elongations were observed at 500{degrees}C on one of these new heats of CuNiBe, similar to that observed in other heats.

  19. Strategies for the implementation of a European Volcano Observations Research Infrastructure (United States)

    Puglisi, Giuseppe


    Active volcanic areas in Europe constitute a direct threat to millions of people on both the continent and adjacent islands. Furthermore, eruptions of "European" volcanoes in overseas territories, such as in the West Indies, an in the Indian and Pacific oceans, can have a much broader impacts, outside Europe. Volcano Observatories (VO), which undertake volcano monitoring under governmental mandate and Volcanological Research Institutions (VRI; such as university departments, laboratories, etc.) manage networks on European volcanoes consisting of thousands of stations or sites where volcanological parameters are either continuously or periodically measured. These sites are equipped with instruments for geophysical (seismic, geodetic, gravimetric, electromagnetic), geochemical (volcanic plumes, fumaroles, groundwater, rivers, soils), environmental observations (e.g. meteorological and air quality parameters), including prototype deployment. VOs and VRIs also operate laboratories for sample analysis (rocks, gases, isotopes, etc.), near-real time analysis of space-borne data (SAR, thermal imagery, SO2 and ash), as well as high-performance computing centres; all providing high-quality information on the current status of European volcanoes and the geodynamic background of the surrounding areas. This large and high-quality deployment of monitoring systems, focused on a specific geophysical target (volcanoes), together with the wide volcanological phenomena of European volcanoes (which cover all the known volcano types) represent a unique opportunity to fundamentally improve the knowledge base of volcano behaviour. The existing arrangement of national infrastructures (i.e. VO and VRI) appears to be too fragmented to be considered as a unique distributed infrastructure. Therefore, the main effort planned in the framework of the EPOS-PP proposal is focused on the creation of services aimed at providing an improved and more efficient access to the volcanological facilities

  20. Optimisation extraction of chondroitin sulfate from fish bone by high intensity pulsed electric fields. (United States)

    He, Guidan; Yin, Yongguang; Yan, Xiaoxia; Yu, Qingyu


    High intensity pulsed electric fields (PEF) was used to extract chondroitin sulphate (CS) from fish bone. Results show that PEF extraction speed is much faster, and the content of CS is much higher compared with traditional methods. Variation of PEF parameters and the content of CS were determined by single factor experiments. The processing conditions were optimised by quadratic general rotary unitised design experiments. The maximum yield of 6.92 g/L was achieved under the following conditions: material-liquid ratio of 1:15 g/mL, electric field intensity of 16.88 kV/cm, pulse number of 9, and NaOH concentration of 3.24%. The purity of CS was analysed by agarose gel electrophoresis. CS purity was high, and the extract did not contain any other glycosaminoglycans. PEF can be widely used to extract CS with non-thermal performance, high speed, and low pollution.

  1. High-Altitude Aircraft-Based Electric-Field Measurements Above Thunderstorms (United States)

    Bateman, M. G.; Blakeslee, R. J.; Bailey, J. C.; Stewart, M. F.; Blair, A. K.


    We have developed a new set of eight electric field mills that were flown on a NASA ER-2 high-altitude aircraft. During the Third Convection And Moisture EXperiment (CAMEX-3; Fall, 1998), measurements of electric field, storm dynamics, and ice microphysics were made over several hurricanes. Concurrently, the TExas-FLorida UNderflights (TEFLUN) program was being conducted to make the same measurements over Gulf Coast thunderstorms. Sample measurements are shown: typical flight altitude is 20km. Our new mills have an internal 16-bit A/D, with a resolution of 0.25V/m per bit at high gain, with a noise level less than the least significant bit. A second, lower gain channel gives us the ability to measure fields as high as 150 kV/m.

  2. High Accuracy Investigation of Microwave Absorption in Polymer Electrical Components on Motherboard of Computers (United States)

    Dašić, P.; Hutanu, C.; Jevremović, V.; Dobra, R.; Risteiu, M.; Ileana, I.


    Electronic operating at high frequencies can have problems with emission of high frequency noise. Once put inside an enclosure, the energy will add in phase at certain frequencies to cause resonances which will hinder the performance of the device. These absorbers are based upon open celled foam impregnated with a carbon coating. It is quite possible that in the near future, microprocessors would be to work on a frequency located in 5 to 10 GHz. In these circumstances it is useful to know how and how much of the electromagnetic field emitted by a microprocessor, it is absorbed by the circuit elements in the immediate vicinity of the microprocessor. The aim of this contribution is to demonstrate throughout high-level experimental analysis how the main electric parameters of polymer materials, which build the printed circuits and the one of electric capacitors and resistors, depend on the frequencies on which they work from the microwave range.

  3. Space Radar Image of Karisoke & Virunga Volcanoes (United States)


    This is a false-color composite of Central Africa, showing the Virunga volcano chain along the borders of Rwanda, Zaire and Uganda. This area is home to the endangered mountain gorillas. The image was acquired on October 3, 1994, on orbit 58 of the space shuttle Endeavour by the Spaceborne Imaging Radar-C/X-band Synthetic Aperture Radar (SIR-C/X-SAR). In this image red is the L-band (horizontally transmitted, vertically received) polarization; green is the C-band (horizontally transmitted and received) polarization; and blue is the C-band (horizontally transmitted and received) polarization. The area is centered at about 2.4 degrees south latitude and 30.8 degrees east longitude. The image covers an area 56 kilometers by 70 kilometers (35 miles by 43 miles). The dark area at the top of the image is Lake Kivu, which forms the border between Zaire (to the right) and Rwanda (to the left). In the center of the image is the steep cone of Nyiragongo volcano, rising 3,465 meters (11,369 feet) high, with its central crater now occupied by a lava lake. To the left are three volcanoes, Mount Karisimbi, rising 4,500 meters (14,800 feet) high; Mount Sabinyo, rising 3,600 meters (12,000 feet) high; and Mount Muhavura, rising 4,100 meters (13,500 feet) high. To their right is Nyamuragira volcano, which is 3,053 meters (10,017 feet) tall, with radiating lava flows dating from the 1950s to the late 1980s. These active volcanoes constitute a hazard to the towns of Goma, Zaire and the nearby Rwandan refugee camps, located on the shore of Lake Kivu at the top left. This radar image highlights subtle differences in the vegetation of the region. The green patch to the center left of the image in the foothills of Karisimbi is a bamboo forest where the mountain gorillas live. The vegetation types in this area are an important factor in the habitat of mountain gorillas. Researchers at Rutgers University in New Jersey and the Dian Fossey Gorilla Fund in London will use this data to produce


    Energy Technology Data Exchange (ETDEWEB)



    A surface resistivity survey was conducted on the Hanford Site over a waste disposal trench that received a large volume of liquid inorganic waste. The objective of the survey was to map the extent of the plume that resulted from the disposal activities approximately 50 years earlier. The survey included six resistivity transects of at least 200m, where each transect provided two-dimensional profile information of subsurface electrical properties. The results of the survey indicated that a low resistivity plume resides at a depth of approximately 25-44 m below ground surface. The target depth was calibrated with borehole data of pore-water electrical conductivity. Due to the high correlation of the pore-water electrical conductivity to nitrate concentration and the high correlation of measured apparent resistivity to pore-water electrical conductivity, inferences were made that proposed the spatial distribution of the apparent resistivity was due to the distribution of nitrate. Therefore, apparent resistivities were related to nitrate, which was subsequently rendered in three dimensions to show that the nitrate likely did not reach the water table and the bounds of the highest concentrations are directly beneath the collection of waste sites.

  5. Pattern of high voltage electrical injuries in the Kashmir valley: a 10-year single centre experience. (United States)

    Kasana, R A; Baba, P U F; Wani, A H


    The objective was to study the clinical profile of high voltage electrical injuries in Kashmir, and various prevention and safety measures to bring down the incidence of such injuries in the future. All patients (176) with high voltage electrical injuries reporting to our centre from January 2001 to December 2010 were included in the study. The most common age group was 20-40 years, with mean age of 29.77 ± 8.98 years. Incidence was higher among the rural population (68.75%) than in urban areas (31.25%), and in the winter months. Electricians comprised 47.16% of victims. The most common mode of injury was touching a live wire directly or indirectly, and was seen in 63.64% of victims. Average total body surface burned was 15.27 ± 10.15 percent. Right upper limb was most commonly involved (64.20% of patients). Compartment syndrome was seen in 40.34% of patients, and fasciotomies on all the affected limbs saved around half of them. An average of 3.91 surgical procedures per patient were performed. Around one-third of the victims required major amputations. Reconstructive procedures were required in 49.43% of patients. Average hospital stay was 26.81 days. Average mortality rate was 2.27%. High voltage electrical injuries are not uncommon in the Kashmir Valley, and electrical workers are at higher risk. The incidence of high voltage injuries would not be so high if the workers were properly trained, hazards of high-tension lines were explained and the use of safety equipment was made mandatory.

  6. Cryogenics Vision Workshop for High-Temperature Superconducting Electric Power Systems Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Energetics, Inc.


    The US Department of Energy's Superconductivity Program for Electric Systems sponsored the Cryogenics Vision Workshop, which was held on July 27, 1999 in Washington, D.C. This workshop was held in conjunction with the Program's Annual Peer Review meeting. Of the 175 people attending the peer review meeting, 31 were selected in advance to participate in the Cryogenics Vision Workshops discussions. The participants represented cryogenic equipment manufactures, industrial gas manufacturers and distributors, component suppliers, electric power equipment manufacturers (Superconductivity Partnership Initiative participants), electric utilities, federal agencies, national laboratories, and consulting firms. Critical factors were discussed that need to be considered in describing the successful future commercialization of cryogenic systems. Such systems will enable the widespread deployment of high-temperature superconducting (HTS) electric power equipment. Potential research, development, and demonstration (RD and D) activities and partnership opportunities for advancing suitable cryogenic systems were also discussed. The workshop agenda can be found in the following section of this report. Facilitated sessions were held to discuss the following specific focus topics: identifying Critical Factors that need to be included in a Cryogenics Vision for HTS Electric Power Systems (From the HTS equipment end-user perspective) identifying R and D Needs and Partnership Roles (From the cryogenic industry perspective) The findings of the facilitated Cryogenics Vision Workshop were then presented in a plenary session of the Annual Peer Review Meeting. Approximately 120 attendees participated in the afternoon plenary session. This large group heard summary reports from the workshop session leaders and then held a wrap-up session to discuss the findings, cross-cutting themes, and next steps. These summary reports are presented in this document. The ideas and suggestions

  7. Aleutian Islands Coastal Resources Inventory and Environmental Sensitivity Maps: VOLCANOS (Volcano Points) (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains point locations of active volcanoes as compiled by Motyka et al., 1993. Eighty-nine volcanoes with eruptive phases in the Quaternary are...

  8. An Analysis of Magnetic Field Environment Near High-Voltage Power Lines and Contact Wires of Electric Railways

    Institute of Scientific and Technical Information of China (English)


    Image method is used in this paper to calculate the value of magnetic field near high-voltage transmission lines and electric railways. Areas in which the magnetic field is less than 0.002 Gauss are given and the magnetic pollution of high-voltage power transmission lines and electric railways is discussed

  9. High-Surface-Area Nitrogen-Doped Reduced Graphene Oxide for Electric Double-Layer Capacitors. (United States)

    Youn, Hee-Chang; Bak, Seong-Min; Kim, Myeong-Seong; Jaye, Cherno; Fischer, Daniel A; Lee, Chang-Wook; Yang, Xiao-Qing; Roh, Kwang Chul; Kim, Kwang-Bum


    A two-step method consisting of solid-state microwave irradiation and heat treatment under NH3 gas was used to prepare nitrogen-doped reduced graphene oxide (N-RGO) with a high specific surface area (1007 m(2)  g(-1) ), high electrical conductivity (1532 S m(-1) ), and low oxygen content (1.5 wt %) for electrical double-layer capacitor applications. The specific capacitance of N-RGO was 291 F g(-1) at a current density of 1 A g(-1) , and a capacitance of 261 F g(-1) was retained at 50 A g(-1) , which indicated a very good rate capability. N-RGO also showed excellent cycling stability and preserved 96 % of the initial specific capacitance after 100 000 cycles. Near-edge X-ray absorption fine-structure spectroscopy results provided evidenced for the recovery of π conjugation in the carbon networks with the removal of oxygenated groups and revealed chemical bonding of the nitrogen atoms in N-RGO. The good electrochemical performance of N-RGO is attributed to its high surface area, high electrical conductivity, and low oxygen content.

  10. Modeling eruptions of Karymsky volcano


    Ozerov, A.; Ispolatov, I.; Lees, J.


    A model is proposed to explain temporal patterns of activity in a class of periodically exploding Strombolian-type volcanos. These patterns include major events (explosions) which follow each other every 10-30 minutes and subsequent tremor with a typical period of 1 second. This two-periodic activity is thought to be caused by two distinct mechanisms of accumulation of the elastic energy in the moving magma column: compressibility of the magma in the lower conduit and viscoelastic response of...

  11. Earthquakes - Volcanoes (Causes and Forecast) (United States)

    Tsiapas, E.


    EARTHQUAKES - VOLCANOES (CAUSES AND FORECAST) ELIAS TSIAPAS RESEARCHER NEA STYRA, EVIA,GREECE TEL.0302224041057 The earthquakes are caused by large quantities of liquids (e.g. H2O, H2S, SO2, ect.) moving through lithosphere and pyrosphere (MOHO discontinuity) till they meet projections (mountains negative projections or projections coming from sinking lithosphere). The liquids are moved from West Eastward carried away by the pyrosphere because of differential speed of rotation of the pyrosphere by the lithosphere. With starting point an earthquake which was noticed at an area and from statistical studies, we know when, where and what rate an earthquake may be, which earthquake is caused by the same quantity of liquids, at the next east region. The forecast of an earthquake ceases to be valid if these components meet a crack in the lithosphere (e.g. limits of lithosphere plates) or a volcano crater. In this case the liquids come out into the atmosphere by the form of gasses carrying small quantities of lava with them (volcano explosion).

  12. A micro-structured Si-based electrodes for high capacity electrical double layer capacitors (United States)

    Krikscikas, Valdas; Oguchi, Hiroyuki; Yanazawa, Hiroshi; Hara, Motoaki; Kuwano, Hiroki


    We challenged to make basis for Si electrodes of electric double layer capacitors (EDLC) used as a power source of micro-sensor nodes. Mcroelectromechanical systems (MEMS) processes were successfully introduced to fabricate micro-structured Si-based electrodes to obtain high surface area which leads to high capacity of EDLCs. Study of fundamental properties revealed that the microstructured electrodes benefit from good wettability to electrolytes, but suffer from electric resistance. We found that this problem can be solved by metal-coating of the electrode surface. Finally we build an EDLC consisting of Au-coated micro-structured Si electrodes. This EDLC showed capacity of 14.3 mF/cm2, which is about 530 times larger than that of an EDLC consisting of flat Au electrodes.

  13. A highly efficient electric additive for enhancing photovoltaic performance of dye-sensitized solar cells

    Institute of Scientific and Technical Information of China (English)


    N-cetylpyridinium iodide (N-CPI) as a new electric additive for enhancing photovoltaic performance of the dye-sensitized solar cell (DSSC) was studied.It showed high efficiency for enhancing both the open-circuit voltage and the short-circuit current density of DSSC when the suitable amount of N-CPI as 0.02 M was added in liquid electrolyte.The energy conversion effi- ciency of DSSC increased from 4.429% to 6.535%,with 47.55% enhancement.Therefore,it is a highly efficient electric addi- tive for DSSC.The intrinsic reason is owing to the special molecular structure of N-CPI,which contains two different polarity groups.As a surfactant,N-CPI could form ordered arrangement in liquid electrolyte,which affects the diffusing ability and the redox reaction of I-/I3-,and further affects the photovoltaic performance of DSSC.

  14. Electrically assisted turbocompound systems for high speed direct injection diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Shahed, S.M.; Beatty, D.J. [Allied Signal Turbocharging Systems (United States)


    Turbocharged diesel engines are already the most efficiency prime movers. Further fuel economy gains are being realized by down-sizing engines but with compromised response. AlliedSignal's Electrical Turbocompounding system solves this challenge and further improves fuel economy and power density. It provides additional boost at low speeds and transfers excess turbocharger power to the crankshaft at high speeds. Analysis using a typical baseline engine shows that at low speeds, boost is increased by 100 to 407 mbars and torque by 12 to 50%, by supplying 0.5 to 2.0 kW power assist. At high speeds, up to 10kW of power can be recovered from the turbocharger, improving efficiency by 6-10%. Transient response analysis shows that with electrical assist turbochargers can reach full boost within 0.3-0.5 seconds. (author)

  15. Active Deformation of Etna Volcano Combing IFSAR and GPS data (United States)

    Lundgren, Paul


    The surface deformation of an active volcano is an important indicator of its eruptive state and its hazard potential. Mount Etna volcano in Sicily is a very active volcano with well documented eruption episodes.

  16. High-temperature tensile deformation behavior of aluminum oxide with and without an applied electric field (United States)

    Campbell, James


    Ceramics are usually considered to be brittle, but under certain conditions some ceramics exhibit a large degree of ductility. They are fine-grained and exhibit superplastic behavior when deformed at high temperatures and low stresses. Whereas superplasticity gives enhanced ductility to metals, it may be the only method for imparting large plasticity to ceramics. Electric fields have been shown to increase ductility, reduce flow stress and reduce cavitation in the superplastic forming of 7475 Al and yttria-stabilized zirconia. Thus, the concurrent application of an electric field may give improved superplastic properties and increased plasticity to a marginally ductile ceramic such as aluminum oxide (alpha-alumina). Fine-grained alumina tensile specimens, formed by dry pressing and sintering a spray-dried powder, were tested in tension at high temperature with and without an electric field of 300 V/cm. Constant strain rate, strain rate cycling and stress relaxation tests were performed. The effects of an electric field on the ductility, flow stress, cavitation and parameters of the Weertman-Dorn deformation equation were measured. Without an electric field, the following deformation parameters were found: the stress exponent n = 2.2, the grain size exponent p = 1.9, the activation energy Q = 490 kJ/mol and the threshold stress sigmao ≈ 0 MPa, indicating structural superplasticity where grain boundary sliding is the predominant deformation mode and was likely accommodated by the motion of grain boundary dislocations. An electric field of 300 V/cm gave a Joule heating temperature increase of ˜30°C and caused the alumina to swell 5--25% (increasing with time), even while under no applied stress, thereby reducing its ductility and flow stress. After correcting for Joule heating and swelling there was still a significant flow stress reduction produced by the field and the following deformation parameters were found: n = 2.2, p = 1.9, Q = 950 kJ/mol and sigmao ≈ 0

  17. High-k Dielectric Passivation: Novel Considerations Enabling Cell Specific Lysis Induced by Electric Fields. (United States)

    Wassermann, Klemens J; Barth, Sven; Keplinger, Franz; Noehammer, Christa; Peham, Johannes R


    A better understanding of the electrodynamic behavior of cells interacting with electric fields would allow for novel scientific insights and would lead to the next generation of cell manipulation, diagnostics, and treatment. Here, we introduce a promising electrode design by using metal oxide high-k dielectric passivation. The thermally generated dielectric passivation layer enables efficient electric field coupling to the fluid sample comprising cells while simultaneously decoupling the electrode ohmically from the electrolyte, allowing for better control and adjustability of electric field effects due to reduced electrochemical reactions at the electrode surface. This approach demonstrates cell-size specific lysis with electric fields in a microfluidic flow-through design resulting in 99.8% blood cell lysis at 6 s exposure without affecting the viability of Gram-positive and Gram-negative bacterial spike-ins. The advantages of this new approach can support next-generation investigations of electrodynamics in biological systems and their exploitation for cell manipulation in multiple fields of medicine, life science, and industry.

  18. Multidimensional High Spatiotemporal Resolution InSAR Time Series Assist Interdisciplinary Space- And Ground-Based Monitoring To Reveal Pre-Eruptive Signals At Nyamulagira Volcano (North Kivu, D.R.C.) (United States)

    d'Oreye, N.; Smets, B.; Kervyn, F.; Kervyn, M.; Albino, F.; Arellano, S. R.; Arjona, A. A.; Carn, S. A.; Fernandez, J.; Galle, B.; Gonzalez, P. J.; Head, E.; Pallero, J.; Prieto, J. F.; Samsonov, S. V.; Tedesco, D.; Tiampo, K. F.; Wauthier, C.


    prior the eruption. Providing that enough SAR data is available with a short latency, and with the help of automated processing and trend change detection algorithms, the MSBAS method opens new opportunities for very high-resolution ground deformation studies and possibly for contributing to interdisciplinary volcano early warning systems.

  19. Electricity Market Games: How Agent-Based Modeling Can Help under High Penetrations of Variable Generation

    Energy Technology Data Exchange (ETDEWEB)

    Gallo, Giulia


    Integrating increasingly high levels of variable generation in U.S. electricity markets requires addressing not only power system and grid modeling challenges but also an understanding of how market participants react and adapt to them. Key elements of current and future wholesale power markets can be modeled using an agent-based approach, which may prove to be a useful paradigm for researchers studying and planning for power systems of the future.

  20. Electric-arc synthesis of soot with high content of higher fullerenes in parallel arc (United States)

    Dutlov, A. E.; Nekrasov, V. M.; Sergeev, A. G.; Bubnov, V. P.; Kareev, I. E.


    Soot with a relatively high content of higher fullerenes (C76, C78, C80, C82, C84, C86, etc.) is synthesized in a parallel arc upon evaporation of pure carbon electrodes. The content of higher fullerenes in soot extract amounts to 13.8 wt % when two electrodes are simultaneously burnt in electric-arc reactor. Such a content is comparable with the content obtained upon evaporation of composite graphite electrodes with potassium carbonate impurity.

  1. High uniformity magnetic coil for search of neutron electric dipole moment

    Energy Technology Data Exchange (ETDEWEB)

    Perez Galvan, A., E-mail: [W.K. Kellogg Radiation Laboratory, California Institute of Technology, Pasadena, CA, 91125 (United States); Plaster, B. [Department of Physics and Astronomy, University of Kentucky, Lexington, KY, 40506 (United States); Boissevain, J.; Carr, R.; Filippone, B.W.; Mendenhall, M.P.; Schmid, R. [W.K. Kellogg Radiation Laboratory, California Institute of Technology, Pasadena, CA, 91125 (United States); Alarcon, R.; Balascuta, S. [Department of Physics, Arizona State University, Tempe, AZ 85287 (United States)


    We present in this article a prototype magnetic coil that has been developed for a new search for the electric dipole moment of the neutron at the Spallation Neutron Source at Oak Ridge National Laboratory. The gradients of the magnetic field generated by the coil have been optimized to reduce known systematic effects and to yield long polarization lifetimes of the trapped particles sampling the highly uniform magnetic field. Measurements of the field uniformity of this prototype magnetic coil are also presented.

  2. High pressure electrical resistivity study on nonlinear bis thiourea cadmium chloride (BTCC) single crystal

    Energy Technology Data Exchange (ETDEWEB)

    Ariponnammal, S.; Radhika, S. [Department of Physics, Gandhigram Rural Institute, Deemed University, Gandhigram - 624 302, Dindigul District, Tamil Nadu (India); Selva Vennila, R. [Department of Physics, Anna University, Chennai - 600 025 (India); Arumugam, S. [Department of Physics, Bharathidasan University, Trichy (India)


    The Bis Thiourea Cadmium Chloride (BTCC) crystals have been crystallized by slow evaporation technique. The lattice parameters of the grown crystals have been determined by the Energy dispersive x-ray diffraction technique (EDXRD) and the structure has been confirmed. The high pressure electrical resistivity study have been carried out on this crystal and the results have been reported here. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  3. Influence of the Thomson effect on the pulse heating of high-current electrical contacts (United States)

    Merkushev, A. G.; Pavleino, M. A.; Pavleino, O. M.; Pavlov, V. A.


    Pulse heating of high-current contacts is notable for the presence of considerable temperature gradients in the contact area, which cause the Thomson effect—the appearance of thermoelectric currents. The amount of this effect against conventional Joule heat release is quantitatively estimated. Pulse heating of electrical contacts is numerically simulated with the use of the Comsol program package. It is demonstrated that thermoelectric currents make a negligible contribution to heating in the case of copper contacts.

  4. Campgrounds in Hawaii Volcanoes National Park (United States)

    National Park Service, Department of the Interior — This dataset provides campground locations in Hawaii Volcanoes National Park. Information about facilities, water availability, permit requirements and type of...

  5. Geochemical evolution of Bolshaya Udina, Malaya Udina, and Gorny Zub Volcanoes, Klyuchevskaya Group (Kamchatka) (United States)

    Churikova, Tatiana; Gordeychik, Boris; Wörner, Gerhard; Flerov, Gleb; Hartmann, Gerald; Simon, Klaus


    The Klyuchevskaya group of volcanoes (KGV) located in the northern part of Kamchatka has the highest magma production rate for any arc worldwide and several of its volcanoes have been studied in considerable detail [e.g. Kersting & Arculus, 1995; Pineau et al., 1999; Dorendorf et al., 2000; Ozerov, 2000; Churikova et al., 2001, 2012, 2015; Mironov et al., 2001; Portnyagin et al., 2007, 2015; Turner et al., 2007]. However, some volcanoes of the KGV including Late-Pleistocene volcanoes Bolshaya Udina, Malaya Udina, Ostraya Zimina, Ovalnaya Zimina, and Gorny Zub were studied only on a reconnaissance basis [Timerbaeva, 1967; Ermakov, 1977] and the modern geochemical studies have not been carried out at all. Among the volcanoes of KGV these volcanoes are closest to the arc trench and may hold information on geochemical zonation with respect to across arc source variations. We present the first major and trace element data on rocks from these volcanoes as well as on their basement. All rocks are medium-calc-alkaline basaltic andesites to dacites except few low-Mg basalts from Malaya Udina volcano. Phenocrysts are mainly olivine, pyroxene, plagioclase and magnetite, Hb-bearing andesites and dacites are rarely found only in subvolcanic intrusions at Bolshaya Udina volcano. Lavas are geochemically similar to the active Bezymianny volcano, however, individual variations for each volcano exist in both major and trace elements. Trace element geochemistry is typical of island arc volcanism. Compared to KGV lavas all studied rocks form very narrow trends in all major element diagrams, which almost do not overlap with the fields of other KGV volcanoes. The lavas are relatively poor in alkalis, TiO2, P2O5, FeO, Ni, Zr, and enriched in SiO2 compared to other KGV volcanics and show greater geochemical and petrological evidence of magmatic differentiation during shallow crustal processing. Basement samples of the Udinskoe plateau lavas to the east of Bolshaya Udina volcano have

  6. Effects of electric fields and collisions on highly excited rubidium atoms

    Energy Technology Data Exchange (ETDEWEB)

    Hammer, N.I.; Compton, R.N. [Tennessee Univ., Dept. of Chemistry and Physics, Knoxville, TN (United States)


    The effects of static and pulsed electric fields on the multiphoton ionization (MPI) of rubidium atoms at both low (atomic beam) and high (heat pipe) densities are studied using tunable OPO lasers. Two-photon excitation of np states is induced by the external electric field at both low and high densities. In addition, np signal is also seen at very low electric fields in the heat pipe, providing evidence for collision mixing as well as field mixing. At low Rb densities strong resonance features are observed in the energy region between the zero field limit (IP) and the field ionization limit. In addition, collisional detachment and charge transfer between excited ns and nd Rb Rydberg states and nozzle-jet cooled polar molecules (acetonitrile and acetone) are studied under crossed-beam conditions. The formation of dipole bound anions for acetone is only seen under nozzle jet expansion conditions and the maximum in the Rydberg electron transfer (RET) rate versus n depends upon the expansion gas (n{sub max} increases in the order H{sub 2}, He, Ne, Ar, Xe). For acetone (low dipole moment and large n{sub max}), collisional detachment dominates the charge transfer, whereas for acetonitrile (high dipole moment and low n{sub max}), charge transfer is seen to dominate the creation of Rb{sup +}. (authors)

  7. Effects of electric fields and collisions on highly excited rubidium atoms (United States)

    Hammer, N. I.; Compton, R. N.


    The effects of static and pulsed electric fields on the multiphoton ionization (MPI) of rubidium atoms at both low (atomic beam) and high (heat pipe) densities are studied using tunable OPO lasers. Two-photon excitation of np states is induced by the external electric field at both low and high densities. In addition, np signal is also seen at very low electric fields in the heat pipe, providing evidence for collision mixing as well as field mixing. At low Rb densities strong resonance features are observed in the energy region between the zero field limit (IP) and the field ionization limit. In addition, collisional detachment and charge transfer between excited ns and nd Rb Rydberg states and nozzle-jet cooled polar molecules (acetonitrile and acetone) are studied under crossed-beam conditions. The formation of dipole bound anions for acetone is only seen under nozzle jet expansion conditions and the maximum in the Rydberg electron transfer (RET) rate versus n depends upon the expansion gas (n_max increases in the order H{2}, He, Ne, Ar, Xe). For acetone (low dipole moment and large n_max), collisional detachment dominates the charge transfer, whereas for acetonitrile (high dipole moment and low n_max), charge transfer is seen to dominate the creation of Rb+.

  8. Study on Miniaturized UHF Antennas for Partial Discharge Detection in High-Voltage Electrical Equipment. (United States)

    Liu, Jingcun; Zhang, Guogang; Dong, Jinlong; Wang, Jianhua


    Detecting partial discharge (PD) is an effective way to evaluate the condition of high-voltage electrical equipment insulation. The UHF detection method has attracted attention due to its high sensitivity, strong interference resistance, and ability to locate PDs. In this paper, a miniaturized equiangular spiral antenna (ESA) for UHF detection that uses a printed circuit board is proposed. I-shaped, L-shaped, and C-shaped microstrip baluns were designed to match the impedance between the ESA and coaxial cable and were verified by a vector network analyzer. For comparison, three other types of UHF antenna were also designed: A microstrip patch antenna, a microstrip slot antenna, and a printed dipole antenna. Their antenna factors were calibrated in a uniform electric field of different frequencies modulated in a gigahertz transverse electromagnetic cell. We performed comparison experiments on PD signal detection using an artificial defect model based on the international IEC 60270 standard. We also conducted time-delay test experiments on the ESA sensor to locate a PD source. It was found that the proposed ESA sensor meets PD signal detection requirements. The sensor's compact size makes it suitable for internal installation in high-voltage electrical equipment.

  9. Structure, electrical characteristics, and high-temperature stability of aerosol jet printed silver nanoparticle films (United States)

    Rahman, Md Taibur; McCloy, John; Ramana, C. V.; Panat, Rahul


    Printed electronics has emerged as a versatile eco-friendly fabrication technique to create sintered nanoparticle (NP) films on arbitrary surfaces with an excellent control over the film microstructure. While applicability of such films for high-temperature applications is not explored previously, herein we report the high-temperature electrical stability of silver (Ag) metal NP films fabricated using an Aerosol Jet based printing technique and demonstrate that this behavior is dictated by changes in the film microstructure. In-situ high temperature (24-500 °C) impedance spectroscopy measurements show that the real part of the impedance increases with increasing temperature up to 150 °C, at which point a decreasing trend prevails until 300 °C, followed again by an increase in impedance. The electrical behavior is correlated with the in-situ grain growth of the Ag NP films, as observed afterwards by scanning electron microscopy and X-ray diffraction (XRD), and could be tailored by controlling the initial microstructure through sintering conditions. Using combined diffraction and spectroscopic analytical methods, it is demonstrated the Aerosol Jet printed Ag NP films exhibit enhanced thermal stability and oxidation resistance. In addition to establishing the conditions for stability of Ag NP films, the results provide a fundamental understanding of the effect of grain growth and reduction in grain boundary area on the electrical stability of sintered NP films.

  10. Removal of phenol by activated alumina bed in pulsed high-voltage electric field

    Institute of Scientific and Technical Information of China (English)

    ZHU Li-nan; MA Jun; YANG Shi-dong


    A new process for removing the pollutants in aqueous solution-activated alumina bed in pulsed high-voltage electric field was investigated for the removal of phenol under different conditions. The experimental results indicated the increase in removal rate with increasing applied voltage, increasing pH value of the solution, aeration, and adding Fe2+. The removal rate of phenol could reach 72.1 % when air aeration flow rate was 1200 ml/min, and 88.2 % when 0.05 mmol/L Fe2+ was added into the solution under the conditions of applied voltage 25 kV, initial phenol concentration of 5 mg/L, and initial pH value 5.5. The addition of sodium carbonate reduced the phenol removal rate. In the pulsed high-voltage electric field, local discharge occurred at the surface of activated alumina, which promoted phenol degradation in the thin water film. At the same time, the space-time distribution of gas-liquid phases was more uniform and the contact areas of the activated species generated from the discharge and the pollutant molecules were much wider due to the effect of the activated alumina bed. The synthetical effects of the pulsed high-voltage electric field and the activated alumina particles accelerated phenol degradation.

  11. Study on Miniaturized UHF Antennas for Partial Discharge Detection in High-Voltage Electrical Equipment

    Directory of Open Access Journals (Sweden)

    Jingcun Liu


    Full Text Available Detecting partial discharge (PD is an effective way to evaluate the condition of high-voltage electrical equipment insulation. The UHF detection method has attracted attention due to its high sensitivity, strong interference resistance, and ability to locate PDs. In this paper, a miniaturized equiangular spiral antenna (ESA for UHF detection that uses a printed circuit board is proposed. I-shaped, L-shaped, and C-shaped microstrip baluns were designed to match the impedance between the ESA and coaxial cable and were verified by a vector network analyzer. For comparison, three other types of UHF antenna were also designed: A microstrip patch antenna, a microstrip slot antenna, and a printed dipole antenna. Their antenna factors were calibrated in a uniform electric field of different frequencies modulated in a gigahertz transverse electromagnetic cell. We performed comparison experiments on PD signal detection using an artificial defect model based on the international IEC 60270 standard. We also conducted time-delay test experiments on the ESA sensor to locate a PD source. It was found that the proposed ESA sensor meets PD signal detection requirements. The sensor’s compact size makes it suitable for internal installation in high-voltage electrical equipment.

  12. Edge-enriched, porous carbon-based, high energy density supercapacitors for hybrid electric vehicles. (United States)

    Kim, Yong Jung; Yang, Cheol-Min; Park, Ki Chul; Kaneko, Katsumi; Kim, Yoong Ahm; Noguchi, Minoru; Fujino, Takeshi; Oyama, Shigeki; Endo, Morinobu


    Supercapacitors can store and deliver energy by a simple charge separation, and thus they could be an attractive option to meet transient high energy density in operating fuel cells and in electric and hybrid electric vehicles. To achieve such requirements, intensive studies have been carried out to improve the volumetric capacitance in supercapacitors using various types and forms of carbons including carbon nanotubes and graphenes. However, conventional porous carbons are not suitable for use as electrode material in supercapacitors for such high energy density applications. Here, we show that edge-enriched porous carbons are the best electrode material for high energy density supercapacitors to be used in vehicles as an auxiliary powertrain. Molten potassium hydroxide penetrates well-aligned graphene layers vertically and consequently generates both suitable pores that are easily accessible to the electrolyte and a large fraction of electrochemically active edge sites. We expect that our findings will motivate further research related to energy storage devices and also environmentally friendly electric vehicles. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Electrical conduction mechanism in bulk ceramic insulators at high voltages until dielectric breakdown (United States)

    Neusel, C.; Jelitto, H.; Schneider, G. A.


    In order to develop and verify a dielectric breakdown model for bulk insulators thicker than 100 μm, the knowledge of the dominating conduction mechanism at high electric fields, or respectively voltages, is necessary. The dielectric breakdown is the electrical failure of an insulator. In some existing breakdown models, ohmic conduction is assumed as dominating conduction mechanism. For verification, the dominating dc conduction mechanism of bulk insulators at room temperature was investigated by applying high voltages up to 70 kV to the insulator until dielectric breakdown occurs. Four conduction models, namely, ohmic, space charge limited, Schottky, and Poole-Frenkel conduction, were employed to identify the dominating conduction mechanism. Comparing the calculated permittivities from the Schottky and Poole-Frenkel coefficients with experimentally measured permittivity, Schottky and Poole-Frenkel conduction can be excluded as dominating conduction mechanism. Based on the current density voltage characteristics (J-V-curve) and the thickness-dependence of the current density, space charge limited conduction (SCLC) was identified to be the dominating conduction mechanism at high voltages leading to dielectric breakdown. As a consequence, breakdown models based on ohmic conduction are not appropriate to explain the breakdown of the investigated bulk insulators. Furthermore, the electrical failure of the examined bulk insulators can only be described correctly by a breakdown model which includes SCLC as conduction mechanism.

  14. High-Lift Propeller Noise Prediction for a Distributed Electric Propulsion Flight Demonstrator (United States)

    Nark, Douglas M.; Buning, Pieter G.; Jones, William T.; Derlaga, Joseph M.


    Over the past several years, the use of electric propulsion technologies within aircraft design has received increased attention. The characteristics of electric propulsion systems open up new areas of the aircraft design space, such as the use of distributed electric propulsion (DEP). In this approach, electric motors are placed in many different locations to achieve increased efficiency through integration of the propulsion system with the airframe. Under a project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR), NASA is designing a flight demonstrator aircraft that employs many "high-lift propellers" distributed upstream of the wing leading edge and two cruise propellers (one at each wingtip). As the high-lift propellers are operational at low flight speeds (take-off/approach flight conditions), the impact of the DEP configuration on the aircraft noise signature is also an important design consideration. This paper describes efforts toward the development of a mulit-fidelity aerodynamic and acoustic methodology for DEP high-lift propeller aeroacoustic modeling. Specifically, the PAS, OVERFLOW 2, and FUN3D codes are used to predict the aerodynamic performance of a baseline high-lift propeller blade set. Blade surface pressure results from the aerodynamic predictions are then used with PSU-WOPWOP and the F1A module of the NASA second generation Aircraft NOise Prediction Program to predict the isolated high-lift propeller noise source. Comparisons of predictions indicate that general trends related to angle of attack effects at the blade passage frequency are captured well with the various codes. Results for higher harmonics of the blade passage frequency appear consistent for the CFD based methods. Conversely, evidence of the need for a study of the effects of increased azimuthal grid resolution on the PAS based results is indicated and will be pursued in future work. Overall, the results indicate that the computational

  15. Igneous Petrogenesis of Tequila Volcano, Western Mexico (United States)

    Vázquez-Duarte, A.; Gómez-Tuena, A.; Díaz-Bravo, B.


    Tequila volcano belongs to a Quaternary volcanic chain that runs in parallel to the Middle American Trench, but that have been constructed within the so-called Tepic-Zacoalco rift: an extensional tectonic structure that has been active for the past 3.5 Ma. This unusual tectonic setting, and the existence of a high-resolution stratigraphy for the Tequila Volcanic Field (Lewis-Kenedi, 2005, Bull Volcanol), provide an excellent opportunity to study andesite petrogenesis. New comprehensive geochemical data allow the recognition of at least four different magmatic series around Tequila: 1) The Santa Rosa intraplate basalts (1.0 - 0.2 Ma), a volcanic plateau constructed along the Santiago River Fault north of Tequila volcano. These Na-alkaline basalts are olivine-phyric, have negligible subduction signatures (Ba/Nb= 11.75 - 49.36), and display Sr-Nd-Pb isotopic compositions that correlate with fractionation indexes, probably indicating melt-crust interactions. 2) A group of vitreous domes and flows of dacitic to rhyolitic compositions, mostly contemporaneous to the Santa Rosa basalts, that were emplaced on the periphery of Tequila volcano. These rocks can have very low Sr and Eu contents but their isotopic compositions are remarkably constant and similar to the Santa Rosa basalts, probably indicating a genetic link through low pressure fractionation in the stability field of plagioclase. 3) The main edifice of Tequila volcano (~0.2 Ma) is made of two pyroxene andesites and dacites with strong subduction signatures (Ba/Nb= 53-112), that inversely correlate with MgO contents, but that follow a diverging evolutionary trend as the rest of the sequences. The isotopic compositions of Tequila main edifice can extend to slightly more enriched values, but do not correlate with fractionation indexes, thus indicating provenance from a different source. 4) The youngest activity on Tequila volcano (~0.09 Ma) is represented by amphibole bearing andesites that erupted through the

  16. Seismic instrumentation plan for the Hawaiian Volcano Observatory (United States)

    Thelen, Weston A.


    The seismic network operated by the U.S. Geological Survey’s Hawaiian Volcano Observatory (HVO) is the main source of authoritative data for reporting earthquakes in the State of Hawaii, including those that occur on the State’s six active volcanoes (Kīlauea, Mauna Loa, Hualālai, Mauna Kea, Haleakalā, Lō‘ihi). Of these volcanoes, Kīlauea and Mauna Loa are considered “very high threat” in a report on the rationale for a National Volcanic Early Warning System (NVEWS) (Ewert and others, 2005). This seismic instrumentation plan assesses the current state of HVO’s seismic network with respect to the State’s active volcanoes and calculates the number of stations that are needed to upgrade the current network to provide a seismic early warning capability for forecasting volcanic activity. Further, the report provides proposed priorities for upgrading the seismic network and a cost assessment for both the installation costs and maintenance costs of the improved network that are required to fully realize the potential of the early warning system.

  17. High thermally conductive and electrically insulating 2D boron nitride nanosheet for efficient heat dissipation of high-power transistors (United States)

    Lin, Ziyuan; Liu, Chunru; Chai, Yang


    High-power transistors suffer greatly from inefficient heat dissipation of the hotspots, which elevate the local temperature and significantly degrade the performance and reliability of the high-power devices. Although various thermal management methods at package-level have been demonstrated, the heat dissipation from non-uniform hotspots at micro/nanoscale still persist in the high power transistors. Here, we develop a method for local thermal management using thermally conductive and electrical insulating few-layer hexagonal boron nitride (h-BN) as heat spreaders and thick counterpart as heat sinks. The electrically insulating characteristic of h-BN nanosheet allows it to be intimately contacted with the hotspot region that is located at the gate electrode edge near the drain side of a high-electron-mobility transistor (HEMT). The high thermal conductivity of h-BN nanosheet, which is quantitatively measured by Raman thermography, reduces the temperature of the hotspot by introducing an additional heat transporting pathway. Our DC and radio-frequency characterizations of the HEMT show the improvement of saturation current, cut-off frequency and maximum oscillation frequency. The finite element simulations show a temperature decrease of ∼32 °C at the hotspot with the use of h-BN nanosheet. This method can be further extended for the micro/nanoscale thermal management of other high-power devices.

  18. Xenon Acquisition Strategies for High-Power Electric Propulsion NASA Missions (United States)

    Herman, Daniel A.; Unfried, Kenneth G.


    Solar electric propulsion (SEP) has been used for station-keeping of geostationary communications satellites since the 1980s. Solar electric propulsion has also benefitted from success on NASA Science Missions such as Deep Space One and Dawn. The xenon propellant loads for these applications have been in the 100s of kilograms range. Recent studies performed for NASA's Human Exploration and Operations Mission Directorate (HEOMD) have demonstrated that SEP is critically enabling for both near-term and future exploration architectures. The high payoff for both human and science exploration missions and technology investment from NASA's Space Technology Mission Directorate (STMD) are providing the necessary convergence and impetus for a 30-kilowatt-class SEP mission. Multiple 30-50- kilowatt Solar Electric Propulsion Technology Demonstration Mission (SEP TDM) concepts have been developed based on the maturing electric propulsion and solar array technologies by STMD with recent efforts focusing on an Asteroid Redirect Robotic Mission (ARRM). Xenon is the optimal propellant for the existing state-of-the-art electric propulsion systems considering efficiency, storability, and contamination potential. NASA mission concepts developed and those proposed by contracted efforts for the 30-kilowatt-class demonstration have a range of xenon propellant loads from 100s of kilograms up to 10,000 kilograms. This paper examines the status of the xenon industry worldwide, including historical xenon supply and pricing. The paper will provide updated information on the xenon market relative to previous papers that discussed xenon production relative to NASA mission needs. The paper will discuss the various approaches for acquiring on the order of 10 metric tons of xenon propellant to support potential near-term NASA missions. Finally, the paper will discuss acquisitions strategies for larger NASA missions requiring 100s of metric tons of xenon will be discussed.

  19. Waste Heat Recovery from High Temperature Off-Gases from Electric Arc Furnace

    Energy Technology Data Exchange (ETDEWEB)

    Nimbalkar, Sachin U [ORNL; Thekdi, Arvind [E3M Inc; Keiser, James R [ORNL; Storey, John Morse [ORNL


    This article presents a study and review of available waste heat in high temperature Electric Arc Furnace (EAF) off gases and heat recovery techniques/methods from these gases. It gives details of the quality and quantity of the sensible and chemical waste heat in typical EAF off gases, energy savings potential by recovering part of this heat, a comprehensive review of currently used waste heat recovery methods and potential for use of advanced designs to achieve a much higher level of heat recovery including scrap preheating, steam production and electric power generation. Based on our preliminary analysis, currently, for all electric arc furnaces used in the US steel industry, the energy savings potential is equivalent to approximately 31 trillion Btu per year or 32.7 peta Joules per year (approximately $182 million US dollars/year). This article describes the EAF off-gas enthalpy model developed at Oak Ridge National Laboratory (ORNL) to calculate available and recoverable heat energy for a given stream of exhaust gases coming out of one or multiple EAF furnaces. This Excel based model calculates sensible and chemical enthalpy of the EAF off-gases during tap to tap time accounting for variation in quantity and quality of off gases. The model can be used to estimate energy saved through scrap preheating and other possible uses such as steam generation and electric power generation using off gas waste heat. This article includes a review of the historical development of existing waste heat recovery methods, their operations, and advantages/limitations of these methods. This paper also describes a program to develop and test advanced concepts for scrap preheating, steam production and electricity generation through use of waste heat recovery from the chemical and sensible heat contained in the EAF off gases with addition of minimum amount of dilution or cooling air upstream of pollution control equipment such as bag houses.

  20. The experimental studies on electrical conductivities and P-wave velocities of anorthosite at high pressure and high temperature

    Institute of Scientific and Technical Information of China (English)

    白利平; 杜建国; 刘巍; 周文戈


    Results of P-wave velocity (vP) and electrical conductivity measurements on anorthosite are presented from room temperature to 880 (C at 1.0 GPa using ultrasonic transmission technique and impedance spectra technique respectively. The experiments show that the P-wave velocities in anorthosite decrease markedly above 680 (C following the dehydration of hydrous minerals in the rock, and the complex impedances collected from 12 Hz to 105 Hz only indicate the grain interior conduction mechanism at 1.0 GPa, from 410 (C to 750 (C. Because the fluids in the rock have not formed an interconnected network, the dehydration will not pronouncedly enhance the electrical conductivity and change the electrical conduction mechanism. It is concluded that the formation and evolution of the low-velocity zones and high-conductivity layers in the crust may have no correlations, and the dehydration can result in the formation of the low-velocity zones, but cannot simultaneously result in the high-conductivity layers.

  1. Large-N in Volcano Settings: Volcanosri (United States)

    Lees, J. M.; Song, W.; Xing, G.; Vick, S.; Phillips, D.


    We seek a paradigm shift in the approach we take on volcano monitoring where the compromise from high fidelity to large numbers of sensors is used to increase coverage and resolution. Accessibility, danger and the risk of equipment loss requires that we develop systems that are independent and inexpensive. Furthermore, rather than simply record data on hard disk for later analysis we desire a system that will work autonomously, capitalizing on wireless technology and in field network analysis. To this end we are currently producing a low cost seismic array which will incorporate, at the very basic level, seismological tools for first cut analysis of a volcano in crises mode. At the advanced end we expect to perform tomographic inversions in the network in near real time. Geophone (4 Hz) sensors connected to a low cost recording system will be installed on an active volcano where triggering earthquake location and velocity analysis will take place independent of human interaction. Stations are designed to be inexpensive and possibly disposable. In one of the first implementations the seismic nodes consist of an Arduino Due processor board with an attached Seismic Shield. The Arduino Due processor board contains an Atmel SAM3X8E ARM Cortex-M3 CPU. This 32 bit 84 MHz processor can filter and perform coarse seismic event detection on a 1600 sample signal in fewer than 200 milliseconds. The Seismic Shield contains a GPS module, 900 MHz high power mesh network radio, SD card, seismic amplifier, and 24 bit ADC. External sensors can be attached to either this 24-bit ADC or to the internal multichannel 12 bit ADC contained on the Arduino Due processor board. This allows the node to support attachment of multiple sensors. By utilizing a high-speed 32 bit processor complex signal processing tasks can be performed simultaneously on multiple sensors. Using a 10 W solar panel, second system being developed can run autonomously and collect data on 3 channels at 100Hz for 6 months

  2. Three-dimensional conductivity model of crust and uppermost mantle at the northern Trans North China Orogen: Evidence for a mantle source of Datong volcanoes (United States)

    Zhang, Huiqian; Huang, Qinghua; Zhao, Guoze; Guo, Zhen; Chen, Y. John


    While the Eastern Block of North China Craton (NCC) had experienced significant lithospheric destruction in the Mesozoic, the Western Block of NCC and the Trans North China Orogen (TNCO) have undergone localized lithospheric modification since the Cenozoic. The northern TNCO is highlighted by the Cenozoic magmatic activities including Hannuoba basalts and Datong volcanoes and is a seismically active region. In this study 3-D electrical conductivity model of the crust and uppermost mantle is derived by the 3-D inversion technique using data from 72 broadband magnetotelluric (MT) stations. The final model shows that a 15 km thick resistive layer of about 3000 Ω m dominates the upper crust, which may represent the intact Archean and Paleoproterozoic terrains. Whereas in the mid-crust there are marked high conductivity anomalies of about 10 Ω m beneath Shanxi rifting basin, which may result from the interconnected saline fluid of 0.2% to 6% volume fraction. The most important finding is that one significant conductor extended into the mantle is located between Hannuoba field and Datong volcanoes and it connects with the mid-crust conductor beneath the Datong volcanoes. We suggest that this could be the mantle source (partial melting region) for the Quaternary volcanic activities of Datong volcanoes and the melt fraction is estimated as 6.6%. Its location inside the Western Block suggests that the volcanic activities at Datong volcanoes are irrelevant to the tectonic process to the east of TNCO. It is likely to be related to the mantle flows from the Tibetan Plateau around the Ordos block which converges at the northeastern corner of the Ordos block and local upward flow along the slope of the thinning lithosphere resulted in decompression partial melting and the melt percolated upward through the crust to feed the lava eruptions at the Datong volcanoes to the east. Finally, large crustal earthquakes in this region are generally located in resistive zones with high

  3. A Preliminary Study of Seismicity at Ceboruco, Volcano, Nayarit, Mexico (United States)

    Sanchez, J. J.; Nunez-Cornu, F. J.; Suarez-Plascencia, C.; Trejo-Gomez, E.


    Ceboruco Volcano is located northwestern of Tepic-Zacoalco graben (Jalisco, Mexico). Its volcanic activity can be divided in four eruptive cycles differentiated by their volcano explosivity index (VEI) and chemical variations as well. As a result of andesitic effusive activity, during the first cycle the "paleo-Ceboruco" edifice was constructed. The end of this cycle is defined by a plinian eruption (VEI is estimated between 3 and 4) which occurred some 1020 years ago and formed the external caldera. During the second cycle an andesitic dome extruded in the interior of the caldera. The dome, called Dos Equis, collapsed and formed the internal caldera. The third cycle is represented by andesitic lava flows which partially cover the northern and south-southwestern part of the edifice. The last cycle is represented by historic andesitic lava flows located in the southwestern flank of the volcano. In February 2003 as part of an agreement with Nayarit Civil Defense a seismic station was installed in the SW flank of the volcano. The station is equipped with a Marslite (lennartz) digitizer with a 3DLe 1Hz. seismic sensor. Detection system is based on a STA/LTA recording algorithm. More than 2000 small earthquakes have been attributed to various local sources, and some of this earthquakes are possibly located beneath Ceboruco volcano. A preliminary classification separates high frequency and low frequency seismic events. The sources of high frequency earthquakes appear to be distributed as evidenced from waveforms variety and changing S-P arrivals separations. The low frequency seismic events also show varying signatures and some of them exhibit extended coda, including some monochromatic character.

  4. Research on Methods for Building Volcano Disaster Information System--taking Changbai Mountain as an example

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xuexia; BO Liqun; LU Xingchang


    Volcano eruption is one of the most serious geological disasters in the world. There are volcanoes in every territory on the earth, about a thousand in China, among which Changbai Mountain Volcano, Wudalianchi Volcano and Tengchong Volcano are the most latent catastrophic eruptive active volcanoes. The paper, following an instance of Changbai Mountain Volcano, expounds that monitoring, forecasting and estimating volcano disaster by building Volcano Disaster Information System (VDIS) is feasible to alleviate volcano disaster.

  5. Rapid fluid disruption: A source for self-potential anomalies on volcanoes (United States)

    Johnston, M.J.S.; Byerlee, J.D.; Lockner, D.


    Self-potential (SP) anomalies observed above suspected magma reservoirs, dikes, etc., on various volcanoes (Kilauea, Hawaii; Mount Unzen, Japan; Piton de la Fournaise, Reunion Island, Miyake Jima, Japan) result from transient surface electric fields of tens of millivolts per kilometer and generally have a positive polarity. These SP anomalies are usually attributed to electrokinetic effects where properties controlling this process are poorly constrained. We propose an alternate explanation that contributions to electric fields of correct polarity should be expected from charge generation by fluid vaporization/disruption. As liquids are vaporized or removed as droplets by gas transport away from hot dike intrusions, both charge generation and local increase in electrical resistivity by removal of fluids should occur. We report laboratory observations of electric fields in hot rock samples generated by pulses of fluid (water) through the rock at atmospheric pressure. These indicate the relative amplitudes of rapid fluid disruption (RFD) potentials and electrokinetic potentials to be dramatically different and the signals are opposite in sign. Above vaporization temperatures, RFD effects of positive sign in the direction of gas flow dominate, whereas below these temperatures, effects of negative sign dominate. This suggests that the primary contribution to observed self-potential anomalies arises from gas-related charge transport processes at temperatures high enough to produce vigorous boiling and vapor transport. At lower temperatures, the primary contribution is from electrokinetic effects modulated perhaps by changing electrical resistivity and RFD effects from high-pressure but low-temperature CO2 and SO2 gas flow ripping water molecules from saturated crustal rocks. If charge generation is continuous, as could well occur above a newly emplaced dike, positive static potentials will be set up that could be sustained for many years, and the simplest method for

  6. Insights into magmatic evolution and recharge history in Capraia Volcano (Italy) from chemical and isotopic zoning in plagioclase phenocrysts

    DEFF Research Database (Denmark)

    Gagnevin, D.; Waight, Tod Earle; Daly, J.S.


    Plagioclase phenocrysts in dacites from the high-K calc-alkaline CapraiaVolcano were investigated for major, trace element and Sr isotope variations in order to gain better insight into the proposed open-system behaviour of the volcano. Repeated dissolution zone in plagioclases from the early-eru...

  7. Highly stretchable electric circuits from a composite material of silver nanoparticles and elastomeric fibres. (United States)

    Park, Minwoo; Im, Jungkyun; Shin, Minkwan; Min, Yuho; Park, Jaeyoon; Cho, Heesook; Park, Soojin; Shim, Mun-Bo; Jeon, Sanghun; Chung, Dae-Young; Bae, Jihyun; Park, Jongjin; Jeong, Unyong; Kim, Kinam


    Conductive electrodes and electric circuits that can remain active and electrically stable under large mechanical deformations are highly desirable for applications such as flexible displays, field-effect transistors, energy-related devices, smart clothing and actuators. However, high conductivity and stretchability seem to be mutually exclusive parameters. The most promising solution to this problem has been to use one-dimensional nanostructures such as carbon nanotubes and metal nanowires coated on a stretchable fabric, metal stripes with a wavy geometry, composite elastomers embedding conductive fillers and interpenetrating networks of a liquid metal and rubber. At present, the conductivity values at large strains remain too low to satisfy requirements for practical applications. Moreover, the ability to make arbitrary patterns over large areas is also desirable. Here, we introduce a conductive composite mat of silver nanoparticles and rubber fibres that allows the formation of highly stretchable circuits through a fabrication process that is compatible with any substrate and scalable for large-area applications. A silver nanoparticle precursor is absorbed in electrospun poly (styrene-block-butadiene-block-styrene) (SBS) rubber fibres and then converted into silver nanoparticles directly in the fibre mat. Percolation of the silver nanoparticles inside the fibres leads to a high bulk conductivity, which is preserved at large deformations (σ ≈ 2,200 S cm(-1) at 100% strain for a 150-µm-thick mat). We design electric circuits directly on the electrospun fibre mat by nozzle printing, inkjet printing and spray printing of the precursor solution and fabricate a highly stretchable antenna, a strain sensor and a highly stretchable light-emitting diode as examples of applications.

  8. Highly stretchable electric circuits from a composite material of silver nanoparticles and elastomeric fibres (United States)

    Park, Minwoo; Im, Jungkyun; Shin, Minkwan; Min, Yuho; Park, Jaeyoon; Cho, Heesook; Park, Soojin; Shim, Mun-Bo; Jeon, Sanghun; Chung, Dae-Young; Bae, Jihyun; Park, Jongjin; Jeong, Unyong; Kim, Kinam


    Conductive electrodes and electric circuits that can remain active and electrically stable under large mechanical deformations are highly desirable for applications such as flexible displays, field-effect transistors, energy-related devices, smart clothing and actuators. However, high conductivity and stretchability seem to be mutually exclusive parameters. The most promising solution to this problem has been to use one-dimensional nanostructures such as carbon nanotubes and metal nanowires coated on a stretchable fabric, metal stripes with a wavy geometry, composite elastomers embedding conductive fillers and interpenetrating networks of a liquid metal and rubber. At present, the conductivity values at large strains remain too low to satisfy requirements for practical applications. Moreover, the ability to make arbitrary patterns over large areas is also desirable. Here, we introduce a conductive composite mat of silver nanoparticles and rubber fibres that allows the formation of highly stretchable circuits through a fabrication process that is compatible with any substrate and scalable for large-area applications. A silver nanoparticle precursor is absorbed in electrospun poly (styrene-block-butadiene-block-styrene) (SBS) rubber fibres and then converted into silver nanoparticles directly in the fibre mat. Percolation of the silver nanoparticles inside the fibres leads to a high bulk conductivity, which is preserved at large deformations (σ ~ 2,200 S cm-1 at 100% strain for a 150-µm-thick mat). We design electric circuits directly on the electrospun fibre mat by nozzle printing, inkjet printing and spray printing of the precursor solution and fabricate a highly stretchable antenna, a strain sensor and a highly stretchable light-emitting diode as examples of applications.

  9. A pulse-compression-ring circuit for high-efficiency electric propulsion. (United States)

    Owens, Thomas L


    A highly efficient, highly reliable pulsed-power system has been developed for use in high power, repetitively pulsed inductive plasma thrusters. The pulsed inductive thruster ejects plasma propellant at a high velocity using a Lorentz force developed through inductive coupling to the plasma. Having greatly increased propellant-utilization efficiency compared to chemical rockets, this type of electric propulsion system may one day propel spacecraft on long-duration deep-space missions. High system reliability and electrical efficiency are extremely important for these extended missions. In the prototype pulsed-power system described here, exceptional reliability is achieved using a pulse-compression circuit driven by both active solid-state switching and passive magnetic switching. High efficiency is achieved using a novel ring architecture that recovers unused energy in a pulse-compression system with minimal circuit loss after each impulse. As an added benefit, voltage reversal is eliminated in the ring topology, resulting in long lifetimes for energy-storage capacitors. System tests were performed using an adjustable inductive load at a voltage level of 3.3 kV, a peak current of 20 kA, and a current switching rate of 15 kA/micros.

  10. Electrical resistance stability of high content carbon fiber reinforced cement composite

    Institute of Scientific and Technical Information of China (English)

    YANG Zai-fu; TANG Zu-quan; LI Zhuo-qiu; QIAN Jue-shi


    The influences of curing time, the content of free evaporable water in cement paste, environmental temperature, and alternative heating and cooling on the electrical resistance of high content carbon fiber reinforced cement (CFRC) paste are studied by experiments with specimens of Portland cement 42.5 with 10 mm PAN-based carbon fiber and methylcellulose. Experimental results indicate that the electrical resistance of CFRC increases relatively by 24% within a hydration time of 90 d and almost keeps constant after 14 d, changes hardly with the mass loss of free evaporable water in the concrete dried at 50℃C, increases relatively by 4% when ambient temperature decreases from 15℃ to-20℃, and decreases relatively by 13% with temperature increasing by 88℃. It is suggested that the electric resistance of the CFRC is stable, which is testified by the stable power output obtained by electrifying the CFRC slab with a given voltage. This implies that such kind of high content carbon fiber reinforced cement composite is potentially a desirable electrothermal material for airfield runways and road surfaces deicing.

  11. A new in situ electrical calibration system for high temperature Calvet calorimeters. (United States)

    Razouk, Refat; Hay, Bruno; Himbert, Marc


    A new in situ high temperature electrical calibration system was developed at Laboratoire National de Metrologie et d'Essais, Laboratoire Commun de Metrologie and integrated into a heat flux Calvet calorimeter in order to perform accurate and reliable measurements of enthalpy of fusion that are directly traceable to the International System of Units (SI). This system has been designed to enable the calibration of the calorimeter by electrical substitution (Joule effect) as well as the measurement of enthalpy of fusion in perfectly identical experimental conditions. The metrological features (repeatability, linearity, etc.) of the calorimeter have been evaluated with this system by investigating the influence of some parameters (level of energy, dissipation time, and temperature) on the determination of the sensitivity factor of its thermopiles. Two different procedures, for the calibration and the enthalpy measurements with this new electrical calibration system, have been implemented and tested by measuring the enthalpy of fusion of high purity 6N tin. The results obtained are in very good agreement with those measured by other National Metrology Institutes on the same material.

  12. High-tension electrical injury to the heart as assessed by radionuclide imaging

    Energy Technology Data Exchange (ETDEWEB)

    Iino, Hitoshi; Chikamori, Taishiro; Hatano, Tsuguhisa [Tokyo Medical Coll. (Japan)] [and others


    The purpose of this study was to evaluate cardiac complications associated with electrical injury, 7 patients with high-tension electrical injury (6,600 V alternating current) underwent {sup 201}Tl and {sup 123}I-metaiodobenzylguanidine (MIBG) imaging in addition to conventional electrocardiographic and echocardiographic assessments. Electrocardiography showed transient atrial fibrillation, second degree atrioventricular block, ST-segment depression, and sinus bradycardia in each patient. Echocardiography showed mild hypokinesis of the anterior wall in only 2 patients, but {sup 201}Tl and {sup 123}I-MIBG myocardial scintigraphy showed an abnormal scan image in 6/7 and 5/6 patients, respectively. Decreased radionuclide accumulation was seen primarily in areas extending from the anterior wall to the septum. Decreased radionuclide accumulation was smaller in extent and milder in degree in {sup 123}I-MIBG than in {sup 201}Tl imaging. These results suggest that even in patients without definite evidence of severe cardiac complications in conventional examinations, radionuclide imaging detects significant damage due to high-tension electrical injury, in which sympathetic nerve dysfunction might be milder than myocardial cell damage. (author)

  13. Ultrabright single-photon source on diamond with electrical pumping at room and high temperatures (United States)

    Fedyanin, D. Yu; Agio, M.


    The recently demonstrated electroluminescence of color centers in diamond makes them one of the best candidates for room temperature single-photon sources. However, the reported emission rates are far off what can be achieved by state-of-the-art electrically driven epitaxial quantum dots. Since the electroluminescence mechanism has not yet been elucidated, it is not clear to what extent the emission rate can be increased. Here we develop a theoretical framework to study single-photon emission from color centers in diamond under electrical pumping. The proposed model comprises electron and hole trapping and releasing, transitions between the ground and excited states of the color center as well as structural transformations of the center due to carrier trapping. It provides the possibility to predict both the photon emission rate and the wavelength of emitted photons. Self-consistent numerical simulations of the single-photon emitting diode based on the proposed model show that the photon emission rate can be as high as 100 kcounts s-1 at standard conditions. In contrast to most optoelectronic devices, the emission rate steadily increases with the device temperature achieving of more than 100 Mcount s-1 at 500 K, which is highly advantageous for practical applications. These results demonstrate the potential of color centers in diamond as electrically driven non-classical light emitters and provide a foundation for the design and development of single-photon sources for optical quantum computation and quantum communication networks operating at room and higher temperatures.

  14. High-field electron transport in GaN under crossed electric and magnetic fields (United States)

    Kochelap, V. A.; Korotyeyev, V. V.; Syngayivska, G. I.; Varani, L.


    High-field electron transport studied in crossed electric and magnetic fields in bulk GaN with doping of 1016 cm-3, compensation around 90% at the low lattice temperature (30 K). It was found the range of the magnetic and electric fields where the non-equilibrium electron distribution function has a complicated topological structure in the momentum space with a tendency to the formation of the inversion population. Field dependences of dissipative and Hall components of the drift velocity were calculated for the samples with short- and open- circuited Hall contacts in wide ranges of applied electric (0 — 20 kV/cm) and magnetic (1 — 10 T) fields. For former sample, field dependences of dissipative and Hall components of the drift velocity have a non-monotonic behavior. The dissipative component has the inflection point which corresponds to the maximum point of the Hall component. For latter sample, the drift velocity demonstrate a usual sub-linear growth without any critical points. We found that GaN samples with controlled resistance of the Hall circuit can be utilized as a electronic high-power switch.

  15. Examining global electricity supply vulnerability to climate change using a high-fidelity hydropower dam model. (United States)

    Turner, Sean W D; Ng, Jia Yi; Galelli, Stefano


    An important and plausible impact of a changing global climate is altered power generation from hydroelectric dams. Here we project 21st century global hydropower production by forcing a coupled, global hydrological and dam model with three General Circulation Model (GCM) projections run under two emissions scenarios. Dams are simulated using a detailed model that accounts for plant specifications, storage dynamics, reservoir bathymetry and realistic, optimized operations. We show that the inclusion of these features can have a non-trivial effect on the simulated response of hydropower production to changes in climate. Simulation results highlight substantial uncertainty in the direction of change in globally aggregated hydropower production (~-5 to +5% change in mean global production by the 2080s under a high emissions scenario, depending on GCM). Several clearly impacted hotspots are identified, the most prominent of which encompasses the Mediterranean countries in southern Europe, northern Africa and the Middle East. In this region, hydropower production is projected to be reduced by approximately 40% on average by the end of the century under a high emissions scenario. After accounting for each country's dependence on hydropower for meeting its current electricity demands, the Balkans countries emerge as the most vulnerable (~5-20% loss in total national electricity generation depending on country). On the flipside, a handful of countries in Scandinavia and central Asia are projected to reap a significant increase in total electrical production (~5-15%) without investing in new power generation facilities. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Volcanic hazards at Atitlan volcano, Guatemala (United States)

    Haapala, J.M.; Escobar Wolf, R.; Vallance, James W.; Rose, William I.; Griswold, J.P.; Schilling, S.P.; Ewert, J.W.; Mota, M.


    Atitlan Volcano is in the Guatemalan Highlands, along a west-northwest trending chain of volcanoes parallel to the mid-American trench. The volcano perches on the southern rim of the Atitlan caldera, which contains Lake Atitlan. Since the major caldera-forming eruption 85 thousand years ago (ka), three stratovolcanoes--San Pedro, Toliman, and Atitlan--have formed in and around the caldera. Atitlan is the youngest and most active of the three volcanoes. Atitlan Volcano is a composite volcano, with a steep-sided, symmetrical cone comprising alternating layers of lava flows, volcanic ash, cinders, blocks, and bombs. Eruptions of Atitlan began more than 10 ka [1] and, since the arrival of the Spanish in the mid-1400's, eruptions have occurred in six eruptive clusters (1469, 1505, 1579, 1663, 1717, 1826-1856). Owing to its distance from population centers and the limited written record from 200 to 500 years ago, only an incomplete sample of the volcano's behavior is documented prior to the 1800's. The geologic record provides a more complete sample of the volcano's behavior since the 19th century. Geologic and historical data suggest that the intensity and pattern of activity at Atitlan Volcano is similar to that of Fuego Volcano, 44 km to the east, where active eruptions have been observed throughout the historical period. Because of Atitlan's moderately explosive nature and frequency of eruptions, there is a need for local and regional hazard planning and mitigation efforts. Tourism has flourished in the area; economic pressure has pushed agricultural activity higher up the slopes of Atitlan and closer to the source of possible future volcanic activity. This report summarizes the hazards posed by Atitlan Volcano in the event of renewed activity but does not imply that an eruption is imminent. However, the recognition of potential activity will facilitate hazard and emergency preparedness.

  17. Study of Energy Losses in High-Voltage Induction Motor Electric Drive

    Directory of Open Access Journals (Sweden)

    Svilen Rachev


    Full Text Available The dynamic behavior during operation of the high-voltage induction motor electric drive has been studied by means of mathematical model developed. The purpose is to draw out more clearly picture of operation of high-voltage induction motor drives. The system of differential equations has been transformed and solved using suitable software. As a result the values of the energy losses components in the induction motor have been obtained according to different values of supply voltage and factor of inertia. Some of the study results have been presented graphically. An analysis has been made and conclusions from the results obtained have been done.

  18. Performance evaluation of high-temperature superconducting current leads for electric utility SMES systems (United States)

    Niemann, R. C.; Cha, Y. S.; Hull, J. R.; Rey, C. M.; Dixon, K. D.

    As part of the U.S. Department of Energy's Superconductivity Technology Program, Argonne National Laboratory and Babcock & Wilcox are developing high-temperature super-conductor (HTS) current leads for application to electric utility superconducting magnetic energy storage systems. A 16,000-A HTS lead has been designed and is being constructed. An evaluation program for component performance was conducted to confirm performance predictions and/or to qualify the design features for construction. Performance of the current lead assemblies will be evaluated in a test program that includes assembly procedures, tooling, and quality assurance; thermal and electrical performance; and flow and mechanical characteristics. Results of the evaluations to date are presented.

  19. A diagnostic system for electrical faults in a high current discharge plasma setup. (United States)

    Nigam, S; Aneesh, K; Navathe, C P; Gupta, P D


    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is ∼4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  20. High-endurance megahertz electrical self-oscillation in Ti/NbOx bilayer structures (United States)

    Li, Shuai; Liu, Xinjun; Nandi, Sanjoy Kumar; Venkatachalam, Dinesh Kumar; Elliman, Robert Glen


    Electrical self-oscillation is reported for a Ti/NbOx negative differential resistance device incorporated in a simple electric circuit configuration. Measurements confirm stable operation of the oscillator at source voltages as low as 1.06 V, and demonstrate frequency control in the range from 2.5 to 20.5 MHz for voltage changes as small as ˜1 V. Device operation is reported for >6.5 × 1010 cycles, during which the operating frequency and peak-to-peak device current decreased by ˜25%. The low operating voltage, large frequency range, and high endurance of these devices makes them particularly interesting for applications such as neuromorphic computing.

  1. High-performance liquid-catalyst fuel cell for direct biomass-into-electricity conversion. (United States)

    Liu, Wei; Mu, Wei; Deng, Yulin


    Herein, we report high-performance fuel cells that are catalyzed solely by polyoxometalate (POM) solution without any solid metal or metal oxide. The novel design of the liquid-catalyst fuel cells (LCFC) changes the traditional gas-solid-surface heterogeneous reactions to liquid-catalysis reactions. With this design, raw biomasses, such as cellulose, starch, and even grass or wood powders can be directly converted into electricity. The power densities of the fuel cell with switchgrass (dry powder) and bush allamanda (freshly collected) are 44 mW cm(-2) and 51 mW cm(-2) respectively. For the cellulose-based biomass fuel cell, the power density is almost 3000 times higher than that of cellulose-based microbial fuel cells. Unlike noble-metal catalysts, POMs are tolerant to most organic and inorganic contaminants. Therefore, almost any raw biomass can be used directly to produce electricity without prior purification.

  2. Data on electrical energy conservation using high efficiency motors for the confidence bounds using statistical techniques. (United States)

    Shaikh, Muhammad Mujtaba; Memon, Abdul Jabbar; Hussain, Manzoor


    In this article, we describe details of the data used in the research paper "Confidence bounds for energy conservation in electric motors: An economical solution using statistical techniques" [1]. The data presented in this paper is intended to show benefits of high efficiency electric motors over the standard efficiency motors of similar rating in the industrial sector of Pakistan. We explain how the data was collected and then processed by means of formulas to show cost effectiveness of energy efficient motors in terms of three important parameters: annual energy saving, cost saving and payback periods. This data can be further used to construct confidence bounds for the parameters using statistical techniques as described in [1].

  3. A diagnostic system for electrical faults in a high current discharge plasma setup (United States)

    Nigam, S.; Aneesh, K.; Navathe, C. P.; Gupta, P. D.


    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is ˜4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  4. Electric anisotropy in high density polyethylene + carbon black composites induced by mechanical deformation

    Energy Technology Data Exchange (ETDEWEB)

    Vigueras-Santiago, E; Hernandez-Lopez, S; Camacho-Lopez, M A; Lara-Sanjuan, O, E-mail: eviguerass@uaemex.m [Laboratorio de Investigacion y Desarrollo de Materiales Avanzados (LIDMA), Facultad de Quimica, UAEM. Paseo Colon esq. con Paseo Tollocan, s/n. C.P. 50000, Toluca (Mexico)


    High density polyethylene + carbon black composites with electrical anisotropy was studied. Electrical anisotropy was induced by uniaxial mechanical deformation and injection moulding. We show that anisotropy depends on the carbon black concentration and percentage deformation. Resistivity had the highest anisotropy resistivity around the percolation threshold. Perpendicular resistivity showed two magnitude orders higher than parallel resistivity for injected samples, whereas resistivity showed an inverse behaviour for 100% tensile samples. Both directions were set respect to the deformation axe. Anisotropy could be explained in terms of the molecular deformation (alignment) of the polymer chains as a response of the deformation process originating a redistribution of the carbon black particles in both directions. Alignment of the polymer chains was evidenced by polarized Raman spectroscopy.

  5. Electrical instability of high-mobility zinc oxynitride thin-film transistors upon water exposure (United States)

    Kim, Dae-Hwan; Jeong, Hwan-Seok; Kwon, Hyuck-In


    We investigate the effects of water absorption on the electrical performance and stability in high-mobility zinc oxynitride (ZnON) thin-film transistors (TFTs). The ZnON TFT exhibits a smaller field-effect mobility, lower turn-on voltage, and higher subthreshold slope with a deteriorated electrical stability under positive gate bias stresses after being exposed to water. From the Hall measurements, an increase of the electron concentration and a decrease of the Hall mobility are observed in the ZnON thin film after water absorption. The observed phenomena are mainly attributed to the water molecule-induced increase of the defective ZnXNY bond and the oxygen vacancy inside the ZnON thin film based on the x-ray photoelectron spectroscopy analysis.

  6. High diffraction efficiency at low electric field in photorefractive polymers doped with arylimine chromophores

    Energy Technology Data Exchange (ETDEWEB)

    Maldonado, J L; Ponce-de-Leon, Y; Ramos-Ortiz, G; RodrIguez, M; Meneses-Nava, M A; Barbosa-Garcia, O [Centro de Investigaciones en Optica A.P. 1-948, 37000 Leon, Gto. (Mexico); Santillan, R [Departamento de Quimica, Centro de Investigacion y de Estudios Avanzados del IPN, A.P. 14-740, 07000 Mexico D.F. (Mexico); Farfan, N, E-mail: jlmr@cio.m [Facultad de QuImica, Departamento de QuImica Organica, Universidad Nacional Autonoma de Mexico, Mexico, D.F., 04510 (Mexico)


    We report on the high photorefractive performance of organic polymers doped with arylimine chromophore (diethylaminosalicylaldiminato)nitrobenzene (H1) and its derivative (diethylaminophenylaldiminato)nitrophenol (H2). Polymer blends of H1 and H2 with PVK : ECZ : C{sub 60} at 25 : 49 : 25 : 1 wt% and H2 : PVK : ECZ : PC{sub 61}BM at the same concentration were fabricated. The electric field (E) steady-state diffraction efficiency dependence and the optical gain were measured through holographic experiments at room temperature. For polymers based on chromophore H2, overmodulation of the diffraction efficiency was measured at just E = 32 V {mu}m{sup -1} obtaining 75%, and for polymers based on H1, diffraction of 87% (overmodulation) at E = 48 V {mu}m{sup -1} was observed. Holographic recording imaging was demonstrated at an electric field of just 10-14 V {mu}m{sup -1}.

  7. Increase in the scattering of electric field lines in a new high voltage SOI MESFET (United States)

    Anvarifard, Mohammad K.


    This paper illustrates a new efficient technique to enhance the critical features of a silicon-on-insulator metal-semiconductor field-effect transistor (SOI MESFET) applied in high voltage applications. The structure we proposed utilizes a new method to scatter the electric field lines along the channel region. Realization of two trenches with different materials, which a trench is created in the channel region and the other one is created in the buried oxide, helps the proposed structure to improve the breakdown voltage, driving current, drain-source conductance, minimum noise figure, unilateral power gain and output power density. Exploring the obtained results, the proposed structure has superior electrical performance in comparison to the conventional structure.

  8. Electrical properties of Y-Ba-Na-Cu-O high Tc superconductors thin films

    Energy Technology Data Exchange (ETDEWEB)

    Verdyan, A. (Center for Theoretical Education Holon (Israel) Raymond and Beverly Sackler Faculty of Exact Sciences, School of Physics and Astronomy, Tel-Aviv Univ. (Israel)); Lapsker, I. (Center for Theoretical Education Holon (Israel) Raymond and Beverly Sackler Faculty of Exact Sciences, School of Physics and Astronomy, Tel-Aviv Univ. (Israel)); Azoulay, J. (Center for Theoretical Education Holon (Israel) Raymond and Beverly Sackler Faculty of Exact Sciences, School of Physics and Astronomy, Tel-Aviv Univ. (Israel))


    Y-Ba-Na-Cu-O high Tc superconductors thin films deposited on MgO substrate by resistive evaporation technique were found to have improved electrical properties as compared to pure Y-Ba-Cu-O thin films similarly prepared. A simple conventional inexpensive vacuum system housing a single resistively tungsten heated source was used for the deposition. Pulverized mixture of Y, BaF[sub 2], NaF and Cu in the appropriate atomic proportion was evaporated onto the substrates whose temperature was held constant at 400 C during the evaporation. In situ heat treatment has been carried out at 700 C under oxygen partial pressure of 7 pa. The films thus obtained were found to have the normal superconductors orthorhombic phase at room temperature without any further ex situ heat treatment. The films were characterized and analyzed by X-ray diffraction auger election spectroscopy and four point dc electrical measurements. (orig.)

  9. Electrical properties of Y-Ba-Na-Cu-O high Tc superconductors thin films (United States)

    Verdyan, A.; Lapsker, I.; Azoulay, J.; Sackler, Raymond; Sackler, Beverly


    Y-Ba-Na-Cu-O high Tc superconductors thin films deposited on MgO substrate by resistive evaporation technique were found to have improved electrical properties as compared to pure Y-Ba-Cu-O thin films similarly prepared. A simple conventional inexpensive vacuum system housing a single resistively tungsten heated source was used for the deposition. Pulverized mixture of Y, BaF 2, NaF and Cu in the appropriate atomic proportion was evaporated onto the substrates whose temperature was held constant at 400°C during the evaporation. In situ heat treatment has been carried out at 700°C under oxygen partial pressure of 7 pa. The films thus obtained were found to have the normal superconductors orthorhombic phase at room temperature without any further ex situ heat treatment. The films were characterized and analyzed by x-ray diffraction auger electron spectroscopy and four point dc electrical measurements.

  10. Electrical characteristics of polycrystalline Si layers embedded into high- k Al 2O 3 gate layers (United States)

    Park, Byoungjun; Cho, Kyoungah; Kim, Sangsig


    The electrical characteristics of polycrystalline Si (poly Si) layers embedded into high- k Al 2O 3 (alumina) gate layers are investigated in this work. The capacitance versus voltage ( C- V) curves obtained from the metal-alumina-polysilicon-alumina-silicon (MASAS) capacitors exhibit significant threshold voltage shifts, and the width of their hysteresis window is dependent on the range of the voltage sweep. The counterclockwise hysteresis observed in the C- V curves indicates that electrons originating from the p-type Si substrate in the inversion condition are trapped in the floating gate layer consisting of the poly Si layer present between the top and bottom Al 2O 3 layers in the MASAS capacitor. Also, current versus voltage ( I- V) measurements are performed to examine the electrical characteristics of the fabricated capacitors. The I- V measurements reveal that our MASAS capacitors show a very low leakage current density, compared to the previously reported results.

  11. Antarctic volcanoes: A remote but significant hazard (United States)

    Geyer, Adelina; Martí, Alex; Folch, Arnau; Giralt, Santiago


    Ash emitted during explosive volcanic eruptions can be dispersed over massive areas of the globe, posing a threat to both human health and infrastructures, such as the air traffic. Some of the last eruptions occurred during this decade (e.g. 14/04/2010 - Eyjafjallajökull, Iceland; 24/05/2011-Grímsvötn, Iceland; 05/06/2011-Puyehue-Cordón Caulle, Chile) have strongly affected the air traffic in different areas of the world, leading to economic losses of billions of euros. From the tens of volcanoes located in Antarctica, at least nine are known to be active and five of them have reported volcanic activity in historical times. However, until now, no attention has been paid to the possible social, economical and environmental consequences of an eruption that would occur on high southern latitudes, perhaps because it is considered that its impacts would be minor or local, and mainly restricted to the practically inhabited Antarctic continent. We show here, as a case study and using climate models, how volcanic ash emitted during a regular eruption of one of the most active volcanoes in Antarctica, Deception Island (South Shetland Islands), could reach the African continent as well as Australia and South America. The volcanic cloud could strongly affect the air traffic not only in the region and at high southern latitudes, but also the flights connecting Africa, South America and Oceania. Results obtained are crucial to understand the patterns of volcanic ash distribution at high southern latitudes with obvious implications for tephrostratigraphical and chronological studies that provide valuable isochrones with which to synchronize palaeoclimate records. This research was partially funded by the MINECO grants VOLCLIMA (CGL2015-72629-EXP)and POSVOLDEC(CTM2016-79617-P)(AEI/FEDER, UE), the Ramón y Cajal research program (RYC-2012-11024) and the NEMOH European project (REA grant 34 agreement n° 289976).

  12. Geology and geochemical evaluation of Taftan Volcano, Sistan and Baluchestan Province, southeast of Iran

    Institute of Scientific and Technical Information of China (English)

    Biabangard H.; Moradian A.


    At a glance of its stratighraphy, the Taftan Volcano can be classified as three groups: pre-, syn- and post-volcanic deposits. The pre-volcanic deposits consist mostly of flysch facies and colored mélange complex. The syn-volcanic deposits are mainly the product of the Taftan Volcano which is mostly composed of pyroclastic and lava flows from the main body of this volcano. The post-volcanic deposits are mostly epiclastic and reworked materials from the Taftan Volcano due to its erosion and weathering. Major and trace elements, and Sr/Rb isotopic compositions determined on whole-rock samples from the Taftan Volcano showed that the volcano was formed at the continental margin. The whole-rock isotopic composition of the Taftan Volcano showed a feature of strong enrichment with 87Sr/86Sr=0.705326-0.705921. Geochronological samples of the Taftan Volcano determined by the 40K/40Ar method gave an age range of 6.95±0.72 to 0.71±0.03 Ma. The rare-earth element patterns are characterized by high LREE and nearly strongly linear patterns for MREE to HREE, suggesting that distinctive minerals such as olivine and pyroxene crystallized in the early magmatic stage and then were involved in reaction between the lower crust and residual magma. The integrated isotope and trace element systematics and tectonic structure beneath the Taftan Volcano suggested the lower-crust assimilation by the primary magma. The primary magma had generated from a heterogeneous mantle source and a secondary petrogenetical process. This magma could have been affected by the subduction of the Oman Sea underneath the continental Eurasia plate.


    Directory of Open Access Journals (Sweden)

    Yu. G. Aliakseyeu


    Full Text Available Electrolyte-plasma treatment has become widespread in the industry as an alternative to traditional chemical, electrochemical and mechanical methods of improving the surface quality of products made of metallic materials. Advantages ofelectrolyte-plasma treatment are a high intensity of microroughness smoothing, the use of low concentration salts solutions as electrolytes, the possibility of processing products of complex shape. The main disadvantage of this method is high power consumption, so the method can be considered in its classical form to the power-consuming. A possible way of reducing power consumption is treatment in unsteady modes that arise in the transition zone between a switching and stable electrolyte-plasma treatment process and is characterized by the periodic formation of a stable vapor-gas shell and a transition to an electrochemical process. The paper presents the results of a study of the influence of a high-gradient electric field under unsteady electrolyte-plasma treatment modes on the energy parameters of the process and the characteristics of the surface being treated. It is established that a high-gradient electric field has a significant effect on the decrease in specific power consumption, which is explained by a decrease in losses in the electrolyte and the influence of the field on the formation and maintenance of the vapor-gas shell. As a result of the study of the effect of a high-gradient electric field in unsteady EPT modes on characteristics of the surface layer was established that a significant impulse current density in the zone of predominantly electrochemical treatment leads to a selective etching of the surface and the formation of a characteristic micro relief of the surface with a developed porous microstructure with pore sizes from 0.3 to 2.5 microns. The most pronounced porous microstructure is provided at a voltage of 270–300 V and an additional inductance of 3.2 mH.

  14. Study of electrical conductivity response upon formation of ice and gas hydrates from salt solutions by a second generation high pressure electrical conductivity probe. (United States)

    Sowa, Barbara; Zhang, Xue Hua; Kozielski, Karen A; Dunstan, Dave E; Hartley, Patrick G; Maeda, Nobuo


    We recently reported the development of a high pressure electrical conductivity probe (HP-ECP) for experimental studies of formation of gas hydrates from electrolytes. The onset of the formation of methane-propane mixed gas hydrate from salt solutions was marked by a temporary upward spike in the electrical conductivity. To further understand hydrate formation a second generation of window-less HP-ECP (MkII), which has a much smaller heat capacity than the earlier version and allows access to faster cooling rates, has been constructed. Using the HP-ECP (MkII) the electrical conductivity signal responses of NaCl solutions upon the formation of ice, tetrahydrofuran hydrates, and methane-propane mixed gas hydrate has been measured. The concentration range of the NaCl solutions was from 1 mM to 3M and the driving AC frequency range was from 25 Hz to 5 kHz. This data has been used to construct an "electrical conductivity response phase diagrams" that summarize the electrical conductivity response signal upon solid formation in these systems. The general trend is that gas hydrate formation is marked by an upward spike in the conductivity at high concentrations and by a drop at low concentrations. This work shows that HP-ECP can be applied in automated measurements of hydrate formation probability distributions of optically opaque samples using the conductivity response signals as a trigger.

  15. Dense Local Seismic Network at Villarrica Volcano (Southern Chile) (United States)

    Mora-Stock, C.; Thorwart, M.; Dzieran, L.; Rabbel, W.


    Villarrica volcano is one of the most active volcanoes in the Southern Andes. It has been presenting constant fumarole activity and seismicity since its last eruption in 1984-85. A local network was installed at Villarrica volcano (Southern Chile) during the first two weeks of March, 2012. In total, 75 DSS-Cube short-period stations (30 3-Component, 45 1-Component) were deployed at and around the volcano area, covering approx. 63 km x 55 km. The average station spacing is 1.5 km for stations inside the perimeter of the volcanic edifice, and 5km outside this perimeter. The network recorded ca. 94 volcano tectonic (VT) events located SSW, SSE and North of the crater, with clear P- and S-wave arrivals. Many others, ca.73 events, could be classified as 'hybrid' events (HB), which present high frequencies at the beginning of the signal, and a sharp and notorious S-wave at the crater stations, but a strong scattering, lower frequency content, and elongated coda on the stations along the volcanic edifice. This strong scattering effect is probably caused by the heterogeneous ash layers on the edifice structure. Few long period events (LP), with main frequencies between 2-4 Hz, were observed. From the tectonic regional events, three sets of events can be distinguished. One coming from the southern end of the focal plane of the Maule earthquake (2010), with S-P wave travel time difference of ca. 30 s or more. Another closer group with S-P wave travel time difference between 10 s and 20 s, and the last group with S-P wave travel time difference of 10 s or less. A cross-correlation analysis to the travel times of the regional events and a teleseismic event from Argentina was applied in order to determine the average velocity structure of the volcano, and obtained an average P-wave velocity of 3.6 km/s for the volcanic edifice inside a radius of 6.5 km, and 4.1 km/s for the surrounding area outside this radius. This model serves as a starting point for local earthquake

  16. Reevaluation of tsunami formation by debris avalanche at Augustine Volcano, Alaska (United States)

    Waythomas, C.F.


    Debris avalanches entering the sea at Augustine Volcano, Alaska have been proposed as a mechanism for generating tsunamis. Historical accounts of the 1883 eruption of the volcano describe 6- to 9-meter-high waves that struck the coastline at English Bay (Nanwalek), Alaska about 80 kilometers east of Augustine Island. These accounts are often cited as proof that volcanigenic tsunamis from Augustine Volcano are significant hazards to the coastal zone of lower Cook Inlet. This claim is disputed because deposits of unequivocal tsunami origin are not evident at more than 50 sites along the lower Cook Inlet coastline where they might be preserved. Shallow water (Augustine Island, in the run-out zone for debris avalanches, limits the size of an avalanche-caused wave. If the two most recent debris avalanches, Burr Point (A.D. 1883) and West Island (Augustine Volcano appears minor, unless a very large debris avalanche occurs at high tide.

  17. 2006-2008 Eruptions and Volcano Hazards Of Soputan Volcano, North Sulawesi, Indonesia (United States)

    Hendratno, K.; Pallister, J. S.; McCausland, W. A.; Kristianto, M.; Bina, F. R.; Carn, S. A.; Haerani, N.; Griswold, J.; Keeler, R.


    Soputan is a basalt volcano located in North Sulawesi near the southern margin of the Quaternary Tondano Caldera. Unusual for a basalt volcano, Soputan produces summit lava domes and explosive eruptions, as well as voluminous basaltic tephra deposits and lava flows. Soputan erupted five times during 2006-2008: on 14 December, 2006, 12-15 August, 2007, 25-26 October, 2007, 5-6 June, 2008, and 5-6 October, 2008. The 2006-2007 eruptions destroyed a lava dome at the volcano’s summit and exposed the conduit, resulting in Vulcanian eruptions and St. Vincent type pyroclastic flows from an open vent structure. We used high-resolution satellite images and digital elevation models to make photo-geologic maps of the deposits from the 2006, 2007 and 2008 eruptions, to estimate volumes of deposits using GIS and to model potential flow hazards. In March, 2008 and in March 2009 we conducted reconnaissance geologic field investigations at Soputan. This work was done to field-check our photo-geologic mapping, to reconstruct the sequence of eruptive events in 2006-2008 and to collect samples for geochemical and petrographic analysis. We also analyzed seismic records and SO2 emission data from the eruptions and we interpreted these data in the context of our geologic and geochemical data to provide insights into the ascent and degassing of magmas. On the basis of the eruptive history and modeling of potential lahar inundation areas we present an updated assessment of volcano hazards and a forecast for future eruptions at Soputan. Our analysis of field and petrologic data indicates that Soputan is an open-system volcano, which taps basalt magma from great depth, apparently with little shallow storage of this magma. Degassing of the magma as it rises within the conduit results in growth of micro-phenocrysts, evolution of the matrix melt and a commensurate increase in the viscosity of the magma. This, in turn, results in growth of lava domes and more explosive eruptions than are

  18. GlobVolcano pre-operational services for global monitoring active volcanoes (United States)

    Tampellini, Lucia; Ratti, Raffaella; Borgström, Sven; Seifert, Frank Martin; Peltier, Aline; Kaminski, Edouard; Bianchi, Marco; Branson, Wendy; Ferrucci, Fabrizio; Hirn, Barbara; van der Voet, Paul; van Geffen, J.


    ), Stromboli and Volcano (Italy), Hilo (Hawai), Mt. St. Helens (United States), CTM (Coherent Target Monitoring): Cumbre Vieja (La Palma) To generate products either Envisat ASAR, Radarsat 1or ALOS PALSAR data have been used. Surface Thermal Anomalies Volcanic hot-spots detection, radiant flux and effusion rate (where applicable) calculation of high temperature surface thermal anomalies such as active lava flow, strombolian activity, lava dome, pyroclastic flow and lava lake can be performed through MODIS (Terra / Aqua) MIR and TIR channels, or ASTER (Terra), HRVIR/HRGT (SPOT4/5) and Landsat family SWIR channels analysis. ASTER and Landsat TIR channels allow relative radiant flux calculation of low temperature anomalies such as lava and pyroclastic flow cooling, crater lake and low temperature fumarolic fields. MODIS, ASTER and SPOT data are processed to detect and measure the following volcanic surface phenomena: Effusive activity Piton de la Fournaise (Reunion Island); Mt Etna (Italy). Lava dome growths, collapses and related pyroclastic flows Soufrière Hills (Montserrat); Arenal - (Costa Rica). Permanent crater lake and ephemeral lava lake Karthala (Comores Islands). Strombolian activity Stromboli (Italy). Low temperature fumarolic fields Nisyros (Greece), Vulcano (Italy), Mauna Loa (Hawaii). Volcanic Emission The Volcanic Emission Service is provided to the users by a link to GSE-PROMOTE - Support to Aviation Control Service (SACS). The aim of the service is to deliver in near-real-time data derived from satellite measurements regarding SO2 emissions (SO2 vertical column density - Dobson Unit [DU]) possibly related to volcanic eruptions and to track the ash injected into the atmosphere during a volcanic eruption. SO2 measurements are derived from different satellite instruments, such as SCIAMACHY, OMI and GOME-2. The tracking of volcanic ash is accomplished by using SEVIRI-MSG data and, in particular, the following channels VIS 0.6 and IR 3.9, and along with IR8.7, IR 10

  19. Geologic Mapping of the Olympus Mons Volcano, Mars (United States)

    Bleacher, J. E.; Williams, D. A.; Shean, D.; Greeley, R.


    We are in the third year of a three-year Mars Data Analysis Program project to map the morphology of the Olympus Mons volcano, Mars, using ArcGIS by ESRI. The final product of this project is to be a 1:1,000,000-scale geologic map. The scientific questions upon which this mapping project is based include understanding the volcanic development and modification by structural, aeolian, and possibly glacial processes. The project s scientific objectives are based upon preliminary mapping by Bleacher et al. [1] along a approx.80-km-wide north-south swath of the volcano corresponding to High Resolution Stereo Camera (HRSC) image h0037. The preliminary project, which covered approx.20% of the volcano s surface, resulted in several significant findings, including: 1) channel-fed lava flow surfaces are areally more abundant than tube-fed surfaces by a ratio of 5:1, 2) channel-fed flows consistently embay tube-fed flows, 3) lava fans appear to be linked to tube-fed flows, 4) no volcanic vents were identified within the map region, and 5) a Hummocky unit surrounds the summit and is likely a combination of non-channelized flows, dust, ash, and/or frozen volatiles. These results led to the suggestion that the volcano had experienced a transition from long-lived tube-forming eruptions to more sporadic and shorter-lived, channel-forming eruptions, as seen at Hawaiian volcanoes between the tholeiitic shield building phase (Kilauea to Mauna Loa) and alkalic capping phase (Hualalai and Mauna Kea).

  20. Deep Stimulation at Newberry Volcano EGS Demonstration (United States)

    Grasso, K.; Cladouhos, T. T.; Petty, S.; Garrison, G. H.; Nordin, Y.; Uddenberg, M.; Swyer, M.


    The Newberry Volcano EGS Demonstration is a 5 year field project designed to demonstrate recent technological advances for engineered geothermal systems (EGS) development. Advances in reservoir stimulation, diverter, and monitoring are being tested in a hot (>300 C), dry well (NWG 55-29) drilled in 2008. These technologies could reduce the cost of electrical power generation. The project began in 2010 with two years of permitting, technical planning, and development of a project-specific Induced Seismicity Mitigation Plan (ISMP), and is funded in part by the Department of Energy. In 2012, the well was hydraulically stimulated with water at pressures below the principle stress for 7 weeks, resulting in hydroshearing. The depth of stimulation was successfully shifted by injection of two pills of Thermally-degradable Zonal Isolation Materials (TZIMs). Injectivity changes, thermal profiles and seismicity indicate that fracture permeability in well NWG 55-29 was enhanced during stimulation. This work successfully demonstrated the viability of large-volume (40,000 m3), low-pressure stimulation coupled with non-mechanical diverter technology, and microseismic monitoring for reservoir mapping. Further analysis and field testing in 2013 indicates further stimulation will be required in order to develop an economically viable reservoir, and is scheduled in 2014. The 2014 stimulation will use improved stimulation and monitoring equipment, better knowledge based on 2012 outcomes, and create a deep EGS reservoir in the hottest part of the wellbore.