WorldWideScience

Sample records for vibration damping materials

  1. Vibrational Damping of Composite Materials

    OpenAIRE

    Biggerstaff, Janet M.

    2006-01-01

    The purpose of this research was to develop new methods of vibrational damping in polymeric composite materials along with expanding the knowledge of currently used vibrational damping methods. A new barrier layer technique that dramatically increased damping in viscoelastic damping materials that interacted with the composite resin was created. A method for testing the shear strength of damping materials cocured in composites was developed. Directional damping materials, where the loss facto...

  2. Vibrational damping of composite materials

    Science.gov (United States)

    Biggerstaff, Janet M.

    The purpose of this research was to develop new methods of vibrational damping in polymeric composite materials along with expanding the knowledge of currently used vibrational damping methods. A new barrier layer technique that dramatically increased damping in viscoelastic damping materials that interacted with the composite resin was created. A method for testing the shear strength of damping materials cocured in composites was developed. Directional damping materials, where the loss factor and modulus could be tailored by changing the angle, were produced and investigated. The addition of particles between composite prepreg layers to increase damping was studied. Electroviscoelastic materials that drastically changed properties such as loss factor and modulus with an applied voltage were manufactured and tested.

  3. Active vibration damping using smart material

    Science.gov (United States)

    Baras, John S.; Yan, Zhuang

    1994-01-01

    We consider the modeling and active damping of an elastic beam using distributed actuators and sensors. The piezoelectric ceramic material (PZT) is used to build the actuator. The sensor is made of the piezoelectric polymer polyvinylidene fluoride (PVDF). These materials are glued on both sides of the beam. For the simple clamped beam, the closed loop controller has been shown to be able to extract energy from the beam. The shape of the actuator and its influence on the closed loop system performance are discussed. It is shown that it is possible to suppress the selected mode by choosing the appropriate actuator layout. It is also shown that by properly installing the sensor and determining the sensor shape we can further extract and manipulate the sensor signal for our control need.

  4. Vibration damping and heat transfer using material phase changes

    Science.gov (United States)

    Kloucek, Petr [Houston, TX; Reynolds, Daniel R [Oakland, CA

    2009-03-24

    A method and apparatus wherein phase changes in a material can dampen vibrational energy, dampen noise and facilitate heat transfer. One embodiment includes a method for damping vibrational energy in a body. The method comprises attaching a material to the body, wherein the material comprises a substrate, a shape memory alloy layer, and a plurality of temperature change elements. The method further comprises sensing vibrations in the body. In addition, the method comprises indicating to at least a portion of the temperature change elements to provide a temperature change in the shape memory alloy layer, wherein the temperature change is sufficient to provide a phase change in at least a portion of the shape memory alloy layer, and further wherein the phase change consumes a sufficient amount of kinetic energy to dampen at least a portion of the vibrational energy in the body. In other embodiments, the shape memory alloy layer is a thin film. Additional embodiments include a sensor connected to the material.

  5. Vibration damping and heat transfer using material phase changes

    Science.gov (United States)

    Kloucek, Petr (Inventor); Reynolds, Daniel R. (Inventor)

    2009-01-01

    A method and apparatus wherein phase changes in a material can dampen vibrational energy, dampen noise and facilitate heat transfer. One embodiment includes a method for damping vibrational energy in a body. The method comprises attaching a material to the body, wherein the material comprises a substrate, a shape memory alloy layer, and a plurality of temperature change elements. The method further comprises sensing vibrations in the body. In addition, the method comprises indicating to at least a portion of the temperature change elements to provide a temperature change in the shape memory alloy layer, wherein the temperature change is sufficient to provide a phase change in at least a portion of the shape memory alloy layer, and further wherein the phase change consumes a sufficient amount of kinetic energy to dampen at least a portion of the vibrational energy in the body. In other embodiments, the shape memory alloy layer is a thin film. Additional embodiments include a sensor connected to the material.

  6. Vibration Damping Materials and Their Applications in Nano/Micro-Electro-Mechanical Systems: A Review.

    Science.gov (United States)

    Choudhary, Nitin; Kaur, Davinder

    2015-03-01

    The present review explores an overall view of the vibration damping materials ranging from traditionally used viscoelastic materials for macroscale damping to hybrid thin film heterostructures for micro-electro-mechanical systems (MEMS). Vibration damping materials like rubbers, polymers, metals, metal-matrix composites and smart materials are reviewed in terms of damping capacity, stiffness, mechanical strength and figure of merit. Nanoscale shape memory alloys, piezoelectric materials, carbon nanotubes, their composites and thin films are promising materials for future nanoscale damping devices. The main focus of this article is on our development of new vibration damping approach for MEMS structures comprising of ferroelastic/ferroelastic thin film heterostructures. For the first time, nanoindentation has been explored as an alternative tool to evaluate the damping capability of actual components (e.g., thin films for MEMS) where production of dynamic mechanical analyzer (DMA) test samples is not feasible. A comprehensive insight on the existing vibration damping materials and our new approach would definitely trigger some important applications in nano- and micro-electro-mechanical systems.

  7. Composite Struts Would Damp Vibrations

    Science.gov (United States)

    Dolgin, Benjamin P.

    1991-01-01

    New design of composite-material (fiber/matrix laminate) struts increases damping of longitudinal vibrations without decreasing longitudinal stiffness or increasing weight significantly. Plies with opposing chevron patterns of fibers convert longitudinal vibrational stresses into shear stresses in intermediate viscoelastic layer, which dissipate vibrational energy. Composite strut stronger than aluminum strut of same weight and stiffness.

  8. Materials for Damping Ambient Acoustic and Vibration Signals Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Long-term exposure to even relatively low levels of acoustic and vibration signals has been shown to be potentially harmful to humans. A new class of piezoelectric...

  9. High-damping-performance magnetorheological material for passive or active vibration control

    Science.gov (United States)

    Liu, Taixiang; Yang, Ke; Yan, Hongwei; Yuan, Xiaodong; Xu, Yangguang

    2016-10-01

    Optical assembly and alignment system plays a crucial role for the construction of high-power or high-energy laser facility, which attempts to ignite fusion reaction and go further to make fusion energy usable. In the optical assembly and alignment system, the vibration control is a key problem needs to be well handled and a material with higher damping performance is much desirable. Recently, a new kind of smart magneto-sensitive polymeric composite material, named magnetorheological plastomer (MRP), was synthesized and reported as a high-performance magnetorheological material and this material has a magneto-enhanced high-damping performance. The MRP behaves usually in an intermediate state between fluid-like magnetorheological fluid and solid-like magnetorheological elastomer. The state of MRP, as well as the damping performance of MRP, can be tuned by adjusting the ratio of hard segments and soft segments, which are ingredients to synthesize the polymeric matrix. In this work, a series of MRP are prepared by dispersing micron-sized, magneto-sensitive carbonyl iron powders with related additives into polyurethane-based, magnetically insensitive matrix. It is found that the damping performance of MRP depends much on magnetic strength, shear rate, carbonyl iron content and shear strain amplitude. Especially, the damping capacity of MRP can be tuned in a large range by adjusting external magnetic field. It is promising that the MRP will have much application in passive and active vibration control, such as vibration reduction in optical assembly and alignment system, vibration isolation or absorption in vehicle suspension system, etc.

  10. Modified Composite Struts Would Damp Vibrations

    Science.gov (United States)

    Chen, Gun-Shing; Dolgin, Benjamin P.

    1993-01-01

    Composite-material (fiber/matrix laminate) struts damping longitudinal vibrations fabricated more easily in proposed new design. Prior design described in "Composite Struts Would Damp Vibrations" (NPO-17914). New design similar except pattern of fibers includes rounded bends (instead of sharp bends) in fibers.

  11. Vibration Damping Circuit Card Assembly

    Science.gov (United States)

    Hunt, Ronald Allen (Inventor)

    2016-01-01

    A vibration damping circuit card assembly includes a populated circuit card having a mass M. A closed metal container is coupled to a surface of the populated circuit card at approximately a geometric center of the populated circuit card. Tungsten balls fill approximately 90% of the metal container with a collective mass of the tungsten balls being approximately (0.07) M.

  12. NOISE AND VIBRATION DAMPING FOR YACHT INTERIOR

    Directory of Open Access Journals (Sweden)

    Murat Aydın

    2016-12-01

    Full Text Available Vibration damping and sound insulation are essential for all vehicles. Because moving parts and external factors such as wind, tracks, etc. can cause vibration and noise. Wave which is a dynamic force, drive system and HVAC systems are the main vibration and noise generators in a vessel. These all can affect comfort level on board yachts. Different types of isolators and absorbers such as sylomer®, cork panels, etc. are used to reduce these effects. Comfort level on board yachts can be increased using these types of materials. Otherwise, discomfort of passenger and crew may increase. These materials not only reduce structure-borne and air-borne noise and vibrations from waves, air, engines, pumps, generators and HVAC systems but also protect vibration sensitive interior or fittings. Noise and vibration evaluation is an important issue for this reason. And, measurement tools must be used not only to minimize this problem but also fulfill the regulations such as “comfort class”. Besides, providing quiet and low vibration increases the costs too. From this point of view, this study aims to explain clearly how noise and vibration damping can be done in a yacht.

  13. Modeling the Dynamic Response of a Carbon-Fiber-Reinforced Plate at Resonant Vibrations Considering the Internal Friction in the Material and the External Aerodynamic Damping

    Science.gov (United States)

    Paimushin, V. N.; Firsov, V. A.; Shishkin, V. M.

    2017-09-01

    The frequency dependence for the dynamic elastic modulus of a Porcher 3692 CFRP at frequencies to 112.5 Hz is obtained from an experimental study on damped flexural vibrations of vertical cantilevered test specimens. A finite-element technique is developed for modeling the dynamic response of a long cantilevered carbon-fiber-plastic plate at resonant flexural vibrations according to the first vibration mode with account of internal damping, aerodynamic drag forces, and the frequency-dependent dynamic elastic modulus of the material. The damping properties of the plate are determined by the logarithmic decrement, which depends on the vibration amplitude of its free edge. Numerical experiments were carried out, which confirmed the accuracy of the technique. It is shown that the logarithmic decrement of the plate in the range of medium and high vibration amplitudes depends mainly on the aerodynamic drag forces.

  14. Passively damped vibration welding system and method

    Science.gov (United States)

    Tan, Chin-An; Kang, Bongsu; Cai, Wayne W.; Wu, Tao

    2013-04-02

    A vibration welding system includes a controller, welding horn, an anvil, and a passive damping mechanism (PDM). The controller generates an input signal having a calibrated frequency. The horn vibrates in a desirable first direction at the calibrated frequency in response to the input signal to form a weld in a work piece. The PDM is positioned with respect to the system, and substantially damps or attenuates vibration in an undesirable second direction. A method includes connecting the PDM having calibrated properties and a natural frequency to an anvil of an ultrasonic welding system. Then, an input signal is generated using a weld controller. The method includes vibrating a welding horn in a desirable direction in response to the input signal, and passively damping vibration in an undesirable direction using the PDM.

  15. Damping of wind turbine tower vibrations

    DEFF Research Database (Denmark)

    Brodersen, Mark Laier; Pedersen, Mikkel Melters

    Damping of wind turbine vibrations by supplemental dampers is a key ingredient for the continuous use of monopiles as support for offshore wind turbines. The present thesis consists of an extended summary with four parts and appended papers [P1-P4] concerning novel strategies for damping of tower...... in a stroke amplifying brace, which amplifies the displacement across the damper and thus reduces the desired level of damper force. For optimal damping of the two lowest tower modes, a novel toggle-brace concept for amplifying the bending deformation of the tower is presented. Numerical examples illustrate...... that a minimum of three braces in a symmetric circumferential configuration are needed to introduce homogeneous damping in the two lowest vibration modes, independent of the rotor direction. A novel hybrid viscous damper concept is described in the second part. The hybriddamper consists of a viscous dash...

  16. Shunted Piezoelectric Vibration Damping Analysis Including Centrifugal Loading Effects

    Science.gov (United States)

    Min, James B.; Duffy, Kirsten P.; Provenza, Andrew J.

    2011-01-01

    Excessive vibration of turbomachinery blades causes high cycle fatigue problems which require damping treatments to mitigate vibration levels. One method is the use of piezoelectric materials as passive or active dampers. Based on the technical challenges and requirements learned from previous turbomachinery rotor blades research, an effort has been made to investigate the effectiveness of a shunted piezoelectric for the turbomachinery rotor blades vibration control, specifically for a condition with centrifugal rotation. While ample research has been performed on the use of a piezoelectric material with electric circuits to attempt to control the structural vibration damping, very little study has been done regarding rotational effects. The present study attempts to fill this void. Specifically, the objectives of this study are: (a) to create and analyze finite element models for harmonic forced response vibration analysis coupled with shunted piezoelectric circuits for engine blade operational conditions, (b) to validate the experimental test approaches with numerical results and vice versa, and (c) to establish a numerical modeling capability for vibration control using shunted piezoelectric circuits under rotation. Study has focused on a resonant damping control using shunted piezoelectric patches on plate specimens. Tests and analyses were performed for both non-spinning and spinning conditions. The finite element (FE) shunted piezoelectric circuit damping simulations were performed using the ANSYS Multiphysics code for the resistive and inductive circuit piezoelectric simulations of both conditions. The FE results showed a good correlation with experimental test results. Tests and analyses of shunted piezoelectric damping control, demonstrating with plate specimens, show a great potential to reduce blade vibrations under centrifugal loading.

  17. Vibration damping using a spiral acoustic black hole.

    Science.gov (United States)

    Lee, Jae Yeon; Jeon, Wonju

    2017-03-01

    This study starts with a simple question: can the vibration of plates or beams be efficiently reduced using a lightweight structure that occupies a small space? As an efficient technique to damp vibration, the concept of an acoustic black hole (ABH) is adopted with a simple modification of the geometry. The original shape of an ABH is a straight wedge-type profile with power-law thickness, with the reduction of vibration in beams or plates increasing as the length of the ABH increases. However, in real-world applications, there exists an upper bound of the length of an ABH due to space limitations. Therefore, in this study, the authors propose a curvilinear shaped ABH using the simple mathematical geometry of an Archimedean spiral, which allows a uniform gap distance between adjacent baselines of the spiral. In numerical simulations, the damping performance increases as the arc length of the Archimedean spiral increases, regardless of the curvature of the spiral in the mid- and high-frequency ranges. Adding damping material to an ABH can also strongly enhance the damping performance while not significantly increasing the weight. In addition, the radiated sound power of a spiral ABH is similar to that of a standard ABH.

  18. Damping heat coefficient - Theoretical and experimental research on a vibrating beam

    Science.gov (United States)

    Mihalec, Marko; Javh, Jaka; Cianetti, Filippo; Moretti, Michele; Rossi, Gianluca; Slavič, Janko; Boltežar, Miha

    2017-07-01

    Vibrating systems dissipate their vibrational energy through different mechanisms, commonly referred to as damping. Damping converts the vibrational energy into other forms, such as heat and sound radiation. Heating of the material is often assumed to be one of the biggest drains of energy; however, the measurable temperature increase is at the level of milli Kelvin and hard to measure. This research introduces a damping heat coefficient, the coefficient of total dissipated energy that is converted into heat. Using this coefficient, the expected temperature change of a beam is theoretically related to its damping ratio. In addition, the damping heat coefficient is determined experimentally by measuring the temperature increase of a vibrating beam. Based on modal damping, it is shown that different amounts of energy are dissipated at different parts of the structure. The numerical heat model was experimentally confirmed.

  19. Directional damping material for integrally damped composite plates

    Science.gov (United States)

    Biggerstaff, Janet M.; Kosmatka, John B.

    1999-06-01

    Current viscoelastic-damping materials behave isotopically so that their stiffness and damping properties are the same in all directions. There is a desire to develop viscoelastic- damping materials that behave orthotropically so that the stiffness and damping properties vary with material orientation. These damping materials can be made othrotropic by embedding rows of thin wires within the viscoelastic damping material. These wires add significant directional stiffness and strength to the damping materials, where the stiffness and strength variation with wire orientation follows classical lamination theory. The presence of these wires introduce different damping mechanisms (longitudinal, transverse, and longitudinal shear damping coefficients) that depend upon mode type and orientation angle. Results from experimental studies show that the magnitude of the loss factor and shear modulus depends upon the mode type and orientation angle of these wires within the damping material. The in-plane axial mode loss factor is highly dependent upon the longitudinal coefficient for (0 degrees) wire orientation, the transverse coefficient for (90 degree) wire orientation, and the longitudinal shear-damping coefficient for all other off-angle wire orientations. The loss factor for the out-of- plane bending and torsion modes is highly dependent upon all three damping coefficients.

  20. Vibration and Damping Analysis of Composite Fiber Reinforced Wind Blade with Viscoelastic Damping Control

    Directory of Open Access Journals (Sweden)

    Tai-Hong Cheng

    2015-01-01

    Full Text Available Composite materials are increasingly used in wind blade because of their superior mechanical properties such as high strength-to-weight and stiffness-to-weight ratio. This paper presents vibration and damping analysis of fiberreinforced composite wind turbine blade with viscoelastic damping treatment. The finite element method based on full layerwise displacement theory was employed to analyze the damping, natural frequency, and modal loss factor of composite shell structure. The lamination angle was considered in mathematical modeling. The curved geometry, transverse shear, and normal strains were exactly considered in present layerwise shell model, which can depict the zig-zag in-plane and out-of-plane displacements. The frequency response functions of curved composite shell structure and wind blade were calculated. The results show that the damping ratio of viscoelastic layer is found to be very sensitive to determination of magnitude of composite structures. The frequency response functions with variety of thickness of damping layer were investigated. Moreover, the natural frequency, modal loss factor, and mode shapes of composite fiber reinforced wind blade with viscoelastic damping control were calculated.

  1. A Resonant Damping Study Using Piezoelectric Materials

    Science.gov (United States)

    Min, J. B.; Duffy, K. P.; Choi, B. B.; Morrison, C. R.; Jansen, R. H.; Provenza, A. J.

    2008-01-01

    Excessive vibration of turbomachinery blades causes high cycle fatigue (HCF) problems requiring damping treatments to mitigate vibration levels. Based on the technical challenges and requirements learned from previous turbomachinery blade research, a feasibility study of resonant damping control using shunted piezoelectric patches with passive and active control techniques has been conducted on cantilever beam specimens. Test results for the passive damping circuit show that the optimum resistive shunt circuit reduces the third bending resonant vibration by almost 50%, and the optimum inductive circuit reduces the vibration by 90%. In a separate test, active control reduced vibration by approximately 98%.

  2. Elementary damping properties in braided composite materials

    Science.gov (United States)

    Dion, Bernard L.; Sadler, Robert; Silverberg, Larry

    1994-05-01

    This paper investigates the damping level trends of three-dimensionally braided composites as a function of matrix material, fiber-matrix interface, fiber braid angle, fiber volume, and axial fiber tow size. With knowledge of such trends, designers may increase the structural damping in a 3-D braided composite component, thereby reducing component vibration, shock response, and fatigue. The logarithmic decrements of the fundamental mode response of cantilevered, 3-D braided composite beam specimens were calculated for comparison. Although the logarithmic decrements of two specimens, differing only in their matrix materials (Tactix 123 and Epon 828), were essentially identical, both were considerably larger than that for steel. The value for the decrement of these two composite specimens' response was taken as a reference. Altering the nature of the fiber-matrix interface by lubricating the fibers before specimen consolidation greatly increased the damping relative to the baseline. Trends of increasing damping were measured with both increasing fiber braid angle and fiber volume. Finally, increasing levels of damping are reported for decreases in axial fiber tow size. Explanations for these trends, based on the possible microscopic and macroscopic nature of the braided composites, are offered.

  3. IMPACT GRINDING OF DAMP MATERIALS

    Directory of Open Access Journals (Sweden)

    Ladaev Nikolay Mikhaylovich

    2012-10-01

    Centrifugal grinders were used to analyze the grinding process. The experimental data have proven that the probability of destruction of damp samples is a lot higher than the one of dry samples, given the same initial dimensions of particles and the loading intensity. The rise in the probability of destruction is stipulated by the fact that that the grinder speed at which crushing is triggered is lower in case of damp samples than in case of dry ones. Expressions for speed that describes destruction initiation and the probability of destruction depending on the type of materials, the moisture content and the loading intensity have been derived.

  4. Damping of Torsional Beam Vibrations by Control of Warping Displacement

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker; Hoffmeyer, David; Ejlersen, Christian

    2016-01-01

    Supplemental damping of torsional beam vibrations is considered by viscous bimoments acting on the axial warping displacement at the beam supports. The concept is illustrated by solving the governing eigenvalue problem for various support configurations with the applied bimoments represented...

  5. Damping and energy dissipation in soft tissue vibrations during running.

    Science.gov (United States)

    Khassetarash, Arash; Hassannejad, Reza; Enders, Hendrik; Ettefagh, Mir Mohammad

    2015-01-21

    It has been well accepted that the vibrations of soft tissue cannot be simulated by a single sinusoidal function. In fact, these vibrations are a combination of several vibration modes. In this study, these modes are extracted applying a recently developed method namely, partly ensemble empirical mode decomposition (PEEMD). Then, a methodology for estimating the damping properties and energy dissipation caused by damping for each mode is used. Applying this methodology on simulated signals demonstrates high accuracy. This methodology is applied to the acceleration signals of the gastrocnemius muscle during sprinting and the differences between the damping properties of different vibration modes were identified. The results were 1) the damping property of high-frequency mode was higher than that for low-frequency modes. 2) All identified modes were in under damped condition, therefore, the vibrations had an oscillatory nature. 3) The damping ratios of lower modes are about 100% increased compared to higher modes. 4) The energy dissipation occurred in lower modes were much more than that for higher mode; According to the power spectrum of the ground reaction force (GRF), which is the input force into the body, the recent finding supports the muscle tuning paradigm. It is suggested that the damping properties and energy dissipation can be used to distinguish between different running conditions (surface, fatigue, etc.). Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. Superconductive material and magnetic field for damping and levitation support and damping of cryogenic instruments

    Science.gov (United States)

    Dolgin, Benjamin P. (Inventor)

    1994-01-01

    A superconductive load bearing support without a mechanical contact and vibration damping for cryogenic instruments in space is presented. The levitation support and vibration damping is accomplished by the use of superconducting magnets and the 'Meissner' effect. The assembly allows for transfer of vibration energy away from the cryogenic instrument which then can be damped by the use of either an electronic circuit or conventional vibration damping mean.

  7. Damping element for reducing the vibration of an airfoil

    Science.gov (United States)

    Campbell, Christian X; Marra, John J

    2013-11-12

    An airfoil (10) is provided with a tip (12) having an opening (14) to a center channel (24). A damping element (16) is inserted within the opening of the center channel, to reduce an induced vibration of the airfoil. The mass of the damping element, a spring constant of the damping element within the center channel, and/or a mounting location (58) of the damping element within the center channel may be adjustably varied, to shift a resonance frequency of the airfoil outside a natural operating frequency of the airfoil.

  8. Uniform stability of damped nonlinear vibrations of an elastic string

    Indian Academy of Sciences (India)

    Here we are concerned about uniform stability of damped nonlinear transverse vibrations of an elastic string fixed at its two ends. The vibrations governed by nonlinear integro-differential equation of Kirchoff type, is shown to possess energy uniformly bounded by exponentially decaying function of time. The result is ...

  9. Uniform stability of damped nonlinear vibrations of an elastic string

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Abstract. Here we are concerned about uniform stability of damped nonlinear trans- verse vibrations of an elastic string fixed at its two ends. The vibrations governed by nonlinear integro-differential equation of Kirchoff type, is shown to possess energy uni- formly bounded by exponentially decaying function of time.

  10. Preliminary Research on Damping Material Composed of Flexible Porous Material and Liquid

    Science.gov (United States)

    Kang, Beomsuk; Okuma, Masaaki; Segawa, Shuhei

    This paper presents a new type of damping material composed of flexible porous material such as polyurethane foam and liquid such as water. This new type of damping material costs less than viscoelastic materials such as Sorbothane, and is anticipated to have a better damping effect. At the same time, installation of the new type of damping material is as easy as that of usual viscoelastic materials. The damping effect of this material on the vibration of a cantilever iron plate is experimentally compared with the one of a viscoelastic material. The damping effect on a rail piece with a length of 1.2m and a weight of 72kg is also experimentally investigated. The experimental results show a good damping effect. The design variables of this new damping material such as the liquid viscosity and the hardness of the porous material are thought to influence the damping effect, consequently are investigated by carrying out vibration testing of a cantilever iron plate (material:SS400, size:300×440×5mm, weight:5.2kg).

  11. Experimental identification of viscous damping in linear vibration

    Science.gov (United States)

    Srikantha Phani, A.; Woodhouse, J.

    2009-01-01

    This paper is concerned with the experimental evaluation of the performance of viscous damping identification methods in linear vibration theory. Both existing and some new methods proposed by the present authors [A.S. Phani, J. Woodhouse, Viscous damping identification in linear vibration, Journal of Sound and Vibration 303 (3-5) (2007) 475-500] are applied to experimental data measured on two test structures: a coupled three cantilever beam with moderate modal overlap and a free-free beam with low modal overlap. The performance of each method is quantified and compared based on three norms and the best methods are identified. The role of complex modes in damping identification from vibration measurements is critically assessed.

  12. Research overview on vibration damping of mistuned bladed disk assemblies

    Directory of Open Access Journals (Sweden)

    Liang ZHANG

    2016-04-01

    Full Text Available Bladed disk assemblies are very important parts in auto engine and gas turbine, and is widely used in practical engineering. The mistuning existing commonly in the bladed disk assemblies can destroy the vibration characteristics of the bladed disk assemblies, which is one of the reasons for the high cycle fatigue failure of bladed disk assemblies, so it is necessary to research how to reduce the vibration of the bladed disk assemblies. On the basis of the review of relevant research at home and abroad, the mistuning vibration mechanism of the bladed disk assemblies is introduced, and the main technical methods of the vibration damping of bladed disk assemblies are reviewed, such as artificially active mistuning, collision damping, friction damping and optimization of the blade position. Some future research directions are presented.

  13. Vibration Control of Double-Beam System with Multiple Smart Damping Members

    OpenAIRE

    Dominik Pisarski; Tomasz Szmidt; Czesław I. Bajer; Bartłomiej Dyniewicz; Jacek M. Bajkowski

    2016-01-01

    A control method to stabilize vibration of a double cantilever system with a set of smart damping blocks is designed and numerically evaluated. The externally controlled magnetorheological sheared elastomer damping block is considered, but other smart materials can be used as well. The robust bang-bang control law for stabilization the bilinear system is elaborated. The key feature of the closed loop controller is the efficiency for different types of initial excitement. By employing the fini...

  14. Damping Estimation Using Free Decays and Ambient Vibration Tests

    DEFF Research Database (Denmark)

    Magalhães, Filipe; Brincker, Rune; Cunha, Álvaro

    2007-01-01

    The accurate identification of modal damping ratios of Civil Engineering structures is a subject of major importance, as the amplitude of structural vibrations in resonance is inversely proportional to these coefficients. Their experimental identification can be performed either from ambient...... vibration or from free vibration tests. In the last case, the structural response after application of an impulse or after the application of harmonic loads can be used. Ambient vibration tests have the strong advantage of being more practical and economical. However, recent applications of both approaches...

  15. Fluid Surface Damping: A Technique for Vibration Suppression of Beams

    Directory of Open Access Journals (Sweden)

    Hany Ghoneim

    1997-01-01

    Full Text Available A fluid surface damping (FSD technique for vibration suppression of beamlikestructures is proposed. The technique is a modification of the surface layer damping method. Two viscoelastic surface layers containing fluid-filled cavities are attached symmetrically to the opposite surfaces of the beam. The cavities on one side are attached to the corresponding cavities on the other side via connection passages. As the beam vibrates, the fluid is pumped back and forth through the connecting passages. Therefore, in addition to the viscoelastic damping provided by the surface layers, the technique offers viscous damping due to the fluid flow through the passage. A mathematical model for the proposed technique is developed, normalized, and solved in the frequency domain to investigate the effect of various parameters on the vibration suppression of a cantilever beam. The steady-state frequency response for a base white-noise excitation is calculated at the beam's free tip and over a frequency range containing the first five resonant frequencies. The parameters investigated are the flow-through passage viscous resistance, the length and location of the layers, the hydraulic capacitance of the fluid-filled cavities, and inertia of the moving fluid (hydraulic inertance. Results indicate that the proposed technique has promising potential in the field of vibration suppression of beamlike structures. With two FSD elements, all peak vibration amplitudes can be well suppressed over the entire frequency spectrum studied.

  16. Experimental Observations on Material Damping at Cryogenic Temperatures

    Science.gov (United States)

    Peng, Chia-Yen; Levine, Marie; Shido, Lillian; Leland, Robert

    2004-01-01

    This paper describes a unique experimental facility designed to measure damping of materials at cryogenic temperatures for the Terrestrial Planet Finder (TPF) mission at the Jet Propulsion Laboratory. The test facility removes other sources of damping in the measurement by avoiding frictional interfaces, decoupling the test specimen from the support system, and by using a non-contacting measurement device. Damping data reported herein are obtained for materials (Aluminum, Aluminum/Terbium/Dysprosium, Titanium, Composites) vibrating in free-free bending modes with low strain levels (< 10(exp -6) ppm). The fundamental frequencies of material samples are ranged from 14 to 202 Hz. To provide the most beneficial data relevant to TPF-like precision optical space missions, the damping data are collected from room temperatures (around 293 K) to cryogenic temperatures (below 40 K) at unevenly-spaced intervals. More data points are collected over any region of interest. The test data shows a significant decrease in viscous damping at cryogenic temperatures. The cryogenic damping can be as low as 10(exp -4) %, but the amount of the damping decrease is a function of frequency and material. However, Titanium 15-3-3-3 shows a remarkable increase in damping at cryogenic temperatures. It demonstrates over one order of magnitude increase in damping in comparison to Aluminum 6061-T6. Given its other properties (e.g., good stiffness and low conductivity) this may prove itself to be a good candidate for the application on TPF. At room temperatures, the test data are correlated well with the damping predicted by the Zener theory. However, large discrepancies at cryogenic temperatures between the Zener theory and the test data are observed.

  17. Model Predictive Vibration Control Efficient Constrained MPC Vibration Control for Lightly Damped Mechanical Structures

    CERN Document Server

    Takács, Gergely

    2012-01-01

    Real-time model predictive controller (MPC) implementation in active vibration control (AVC) is often rendered difficult by fast sampling speeds and extensive actuator-deformation asymmetry. If the control of lightly damped mechanical structures is assumed, the region of attraction containing the set of allowable initial conditions requires a large prediction horizon, making the already computationally demanding on-line process even more complex. Model Predictive Vibration Control provides insight into the predictive control of lightly damped vibrating structures by exploring computationally efficient algorithms which are capable of low frequency vibration control with guaranteed stability and constraint feasibility. In addition to a theoretical primer on active vibration damping and model predictive control, Model Predictive Vibration Control provides a guide through the necessary steps in understanding the founding ideas of predictive control applied in AVC such as: ·         the implementation of ...

  18. New Damped-Jerk trajectory for vibration reduction

    OpenAIRE

    BEAREE, Richard

    2014-01-01

    This paper derives a jerk-shaped profile to address the vibration reduction of underdamped flexible dynamics of motion system. The jerk-limited profile is a widespread smooth command pattern used by modern motion systems. The ability of the jerk-limited profile to cancel the residual vibration of an undamped flexible mode is clearly explained using an equivalent continuous filter representation and the input shaping formalism. This motivates the design of a new jerk-shaped profile, named Damp...

  19. Vacuum-packaged piezoelectric vibration energy harvesters: Damping contributions and autonomy for a wireless sensor system

    NARCIS (Netherlands)

    Elfrink, R.; Renaud, M.; Kamel, T.M.; Nooijer, C. de; Jambunathan, M.; Goedbloed, M.; Hohlfeld, D.; Matova, S.; Pop, V.; Caballero, L.; Schaijk, R. van

    2010-01-01

    This paper describes the characterization of thin-film MEMS vibration energy harvesters based on aluminum nitride as piezoelectric material. A record output power of 85 μW is measured. The parasitic-damping and the energy-harvesting performances of unpackaged and packaged devices are investigated.

  20. High Frequency Longitudinal Damped Vibrations of a Cylindrical Ultrasonic Transducer

    Directory of Open Access Journals (Sweden)

    Mihai Valentin Predoi

    2014-01-01

    Full Text Available Ultrasonic piezoelectric transducers used in classical nondestructive testing are producing in general longitudinal vibrations in the MHz range. A simple mechanical model of these transducers would be very useful for wave propagation numerical simulations, avoiding the existing complicated models in which the real components of the transducer are modeled by finite elements. The classical model for longitudinal vibrations is not adequate because the generated longitudinal wave is not dispersive, the velocity being the same at any frequency. We have adopted the Rayleigh-Bishop model, which avoids these limitations, even if it is not converging to the first but to the second exact longitudinal mode in an elastic rod, as obtained from the complicated Pochhammer-Chree equations. Since real transducers have significant vibrations damping, we have introduced a damping term in the Rayleigh-Bishop model, increasing the imaginary part and keeping almost identical real part of the wavenumber. Common transducers produce amplitude modulated signals, completely attenuated after several periods. This can be modeled by two close frequencies, producing a “beat” phenomenon, superposed on the high damping. For this reason, we introduce a two-rod Rayleigh-Bishop model with damping. Agreement with measured normal velocity on the transducer free surface is encouraging for continuation of the research.

  1. Piezoelectric Vibration Damping Study for Rotating Composite Fan Blades

    Science.gov (United States)

    Min, James B.; Duffy, Kirsten P.; Choi, Benjamin B.; Provenza, Andrew J.; Kray, Nicholas

    2012-01-01

    Resonant vibrations of aircraft engine blades cause blade fatigue problems in engines, which can lead to thicker and aerodynamically lower performing blade designs, increasing engine weight, fuel burn, and maintenance costs. In order to mitigate undesirable blade vibration levels, active piezoelectric vibration control has been investigated, potentially enabling thinner blade designs for higher performing blades and minimizing blade fatigue problems. While the piezoelectric damping idea has been investigated by other researchers over the years, very little study has been done including rotational effects. The present study attempts to fill this void. The particular objectives of this study were: (a) to develop and analyze a multiphysics piezoelectric finite element composite blade model for harmonic forced vibration response analysis coupled with a tuned RLC circuit for rotating engine blade conditions, (b) to validate a numerical model with experimental test data, and (c) to achieve a cost-effective numerical modeling capability which enables simulation of rotating blades within the NASA Glenn Research Center (GRC) Dynamic Spin Rig Facility. A numerical and experimental study for rotating piezoelectric composite subscale fan blades was performed. It was also proved that the proposed numerical method is feasible and effective when applied to the rotating blade base excitation model. The experimental test and multiphysics finite element modeling technique described in this paper show that piezoelectric vibration damping can significantly reduce vibrations of aircraft engine composite fan blades.

  2. Numerical analysis of free vibrations of damped rotating structures

    Science.gov (United States)

    Gupta, K. K.

    1977-01-01

    This paper is concerned with the efficient numerical solution of damped and undamped free vibration problems of rotating structures. While structural discretization is achieved by the finite element method, the associated eigenproblem solution is effected by a combined Sturm sequence and inverse iteration technique that enables the computation of a few required roots only without having to compute any other. For structures of complex configurations, a modal synthesis technique is also presented, which is based on appropriate combinations of eigenproblem solution of various structural components. Such numerical procedures are general in nature, which fully exploit matrix sparsity inherent in finite element discretizations, and prove to be most efficient for the vibration analysis of any damped rotating structure, such as rotating machineries, helicopter and turbine blades, spinning space stations, among others.

  3. Use of electro-magnetic damping for vibration control

    DEFF Research Database (Denmark)

    Stein, George Juraj; Darula, Radoslav; Sorokin, Sergey

    2012-01-01

    Vibration of machines is an unwanted phenomenon, and it is usually of interest to eliminate it. There are various means to be used in order to reach the goal, where the utilization of the electromagnet augmented by an external shunt circuit is analyzed in the paper. The magnetic force is used...... to introduce additional electromagnetic damping into vibrating mechanical system. The hysteretic losses and eddy currents are included in the model, to take into account more realistic dynamic behaviour of the system. The mathematical model of the controller is derived using lumped parameter approach...

  4. Vibration Effects of Nonclassically Damped Building-Piping Systems Subjected to Extreme Loads

    Directory of Open Access Journals (Sweden)

    YongHee Ryu

    2016-01-01

    Full Text Available Piping leakage can occur at T-joint, elbows, valves, or nozzles in nuclear power plants and nonnuclear power plants such as petrochemical plants when subjected to extreme loads and such leakage of piping systems can also lead to fire or explosion. For example, leakage of sodium, toxic gases, or nitrogen in hospitals can cause man-made hazards. The primary objective of this research is to understand the vibration effects due to classical/nonclassical damping with building-piping systems under extreme loads. The current evaluation employed finite-element analysis to calculate the effects of the responses of classically and nonclassically damped building-piping systems. Classical and nonclassical damping matrices for a coupled primary-secondary system were developed based on the Rayleigh equation. A total of 10 selected ground motions were applied to single degree of freedom (SDOF primary-SDOF secondary (2-DOF coupled systems in which the ratios of the natural frequencies between the primary and secondary systems ranged between 0.9 and 1.1. It revealed that the vibration effect of nonclassical damping was significant where the natural frequencies of the two systems were nearly tuned. For piping-material nonlinearity, the effects of nonclassical damping on the result forces of piping systems were not significantly different from those of classical damping.

  5. On Coulomb and Viscosity damped single-degree-of-freedom vibrating systems

    DEFF Research Database (Denmark)

    Jakobsen, J.; Sivebæk, Ion Marius

    2016-01-01

    Attention on friction damping mechanisms could be of interest for vibration reduction, and appears therefore to be desirable. Presentations of textbook analyses on mechanical vibration of a viscosity damped single degree system [mass, spring and eventually damping] are numerous. Often they begin...

  6. Assessment of FGPM shunt damping for vibration reduction of laminated composite beams

    Science.gov (United States)

    Lezgy-Nazargah, M.; Divandar, S. M.; Vidal, P.; Polit, O.

    2017-02-01

    This work addresses theoretical and finite element investigations of functionally graded piezoelectric materials (FGPMs) for shunted passive vibration damping of laminated composite beams. The properties of piezoelectric patches are assumed to vary through the thickness direction following the exponent or power law distribution in terms of the volume fractions of the constituent materials. By employing Hamilton's principle, the governing differential equations of motion are derived. The resulting system of equations of vibration is solved by employing an efficient three-nodded beam element which is based on a refined sinus piezoelectric model. The effects of effective electromechanical coupling coefficients (EEMCCs), different electric shunt circuits and different material compositions on the shunted damping performance are investigated. The optimal values of the electric components belonging to each shunt circuit are numerically determined.

  7. Damping in Materials for Spintronic Applications

    Science.gov (United States)

    Mewes, Claudia

    The next generation of spintronic devices relies strongly on the development of new materials with high spin polarization, optimized intrinsic damping and tunable magnetic anisotropy. Therefore, technological progress in this area depends heavily on the successful search for new materials as well as on a deeper understanding of the fundamental mechanisms of the spin polarization, the damping and the magnetic anisotropy. This talk will focus on different aspects of materials with a low intrinsic relaxation rate. Our results are based on first principles calculations in combination with a non-orthogonal tight-binding model to predict those material properties for complex materials which can be used for example in new spin based memory devices or logic devices. However, the intrinsic damping parameter predicted from first principle calculations does not take into account adjacent layers that are present in the final device. Spin pumping is a well-known contribution that has to be taken into account for practical applications using multilayer structures. More recently a strong unidirectional contribution to the relaxation in exchange bias systems has been observed experimentally. To describe this phenomenon theoretically we use the formalism of an anisotropic Gilbert damping tensor that takes the place of the (scalar) Gilbert damping parameter in the Landau-Lifshitz-Gilbert equation of motion. While for single crystals this anisotropy is expected to be small, making experimental confirmation difficult, the broken symmetry in exchange bias systems provides an excellent testing ground to study the modified magnetization dynamics under the influence of unidirectional damping. C.K.A. Mewes would like to thank her colleague T. Mewes and her students J.B. Mohammadi, A.E. Farrar. We acknowledge support by the NSF-CAREER Award No. 1452670, and NSF-CAREER Award No. 0952929.

  8. Vibration Control of Double-Beam System with Multiple Smart Damping Members

    Directory of Open Access Journals (Sweden)

    Dominik Pisarski

    2016-01-01

    Full Text Available A control method to stabilize vibration of a double cantilever system with a set of smart damping blocks is designed and numerically evaluated. The externally controlled magnetorheological sheared elastomer damping block is considered, but other smart materials can be used as well. The robust bang-bang control law for stabilization the bilinear system is elaborated. The key feature of the closed loop controller is the efficiency for different types of initial excitement. By employing the finite element model, the performance of the controller is validated for strong wind blow load and concentrated impact excitement of the particular point of one of the beams. For each of the excitations, the closed loop control outperforms the optimal passive damping case by over 27% for the considered energy metric.

  9. Numerical and Experimental Characterizations of Damping Properties of SMAs Composite for Vibration Control Systems

    Science.gov (United States)

    Biffi, Carlo Alberto; Bassani, P.; Tuissi, A.; Carnevale, M.; Lecis, N.; LoConte, A.; Previtali, B.

    2012-12-01

    Shape memory alloys (SMAs) are very interesting smart materials not only for their shape memory and superelastic effects but also because of their significant intrinsic damping capacity. The latter is exhibited upon martensitic transformations and especially in martensitic state. The combination of these SMA properties with the mechanical and the lightweight of fiberglass-reinforced polymer (FGRP) is a promising solution for manufacturing of innovative composites for vibration suppression in structural applications. CuZnAl sheets, after laser patterning, were embedded in a laminated composite between a thick FGRP core and two thin outer layers with the aim of maximizing the damping capacity of the beam for passive vibration suppression. The selected SMA Cu66Zn24Al10 at.% was prepared by vacuum induction melting; the ingot was subsequently hot-and-cold rolled down to 0.2 mm thickness tape. The choice of a copper alloy is related to some advantages in comparison with NiTiCu SMA alloys, which was tested for the similar presented application in a previous study: lower cost, higher storage modulus and consequently higher damping properties in martensitic state. The patterning of the SMA sheets was performed by means of a pulsed fiber laser. After the laser processing, the SMA sheets were heat treated to obtain the desired martensitic state at room temperature. The transformation temperatures were measured by differential scanning calorimetry (DSC). The damping properties were determined, at room temperature, on full-scale sheet, using a universal testing machine (MTS), with cyclic tensile tests at different deformation amplitudes. Damping properties were also determined as a function of the temperature on miniature samples with a dynamical mechanical analyzer (DMA). Numerical modeling of the laminated composite, done with finite element method analysis and modal strain energy approaches, was performed to estimate the corresponding total damping capacity and then

  10. Experimental and theoretical investigation of passive damping concepts for member forced and free vibration

    Science.gov (United States)

    Razzaq, Zia; Mykins, David W.

    1987-01-01

    Potential passive damping concepts for use in space structures are identified. The effectiveness of copper brush, wool swab, and silly putty in chamber dampers is investigated through natural vibration tests on a tubular aluminum member. The member ends have zero translation and possess partial rotational restraints. The silly putty in chamber dampers provide the maximum passive damping efficiency. Forced vibration tests are then conducted with one, two, and three damper chambers containing silly putty. Owing to the limitation of the vibrator used, the performance of these dampers could not be evaluated experimentally until the forcing function was disengaged. Nevertheless, their performance is evaluated through a forced dynamic finite element analysis conducted as a part of this investigation. The theoretical results based on experimentally obtained damping ratios indicate that the passive dampers are considerably more effective under member natural vibration than during forced vibration. Also, the maximum damping under forced vibration occurs at or near resonance.

  11. Nonlinear Vibration Characteristics of a Flexible Blade with Friction Damping due to Tip-Rub

    Directory of Open Access Journals (Sweden)

    Dengqing Cao

    2011-01-01

    Full Text Available An approximate approach is proposed in this paper for analyzing the two-dimensional friction contact problem so as to compute the dynamic response of a structure constrained by friction interfaces due to tip-rub. The dynamical equation of motion for a rotational cantilever blade in a centrifugal force field is established. Flow-induced distributed periodic forces and the internal material damping in the blade are accounted for in the governing equation of motion. The Galerkin method is employed to obtain a three-degree-of-freedom oscillator with friction damping due to tip-rub. The combined motion of impact and friction due to tip-rub produced a piecewise linear vibration which is actually nonlinear. Thus, a complete vibration cycle is divided into successive intervals. The system possesses linear vibration characteristic during each of these intervals, which can be determined using analytical solution forms. Numerical simulation shows that the parameters such as gap of the tip and the rotational speed of the blades have significant effects on the dynamical responses of the system. Finally, the nonlinear vibration characteristics of the blade are investigated in terms of the Poincare graph, and the frequency spectrum of the responses and the amplitude-frequency curves.

  12. Active Damping of Vibrations in High-Precision Motion Systems

    NARCIS (Netherlands)

    Babakhani, B.

    2012-01-01

    Technology advancements feed the need for ever faster and more accurate industrial machines. Vibration is a significant source of inaccuracy of such machines. A light-weight design in favor of the speed, and avoiding the use of energy-dissipating materials from the structure to omit any source of

  13. Vibrational absorption spectra from vibrational coupled cluster damped linear response functions calculated using an asymmetric Lanczos algorithm

    DEFF Research Database (Denmark)

    Thomsen, Bo; Hansen, Mikkel Bo; Seidler, Peter

    2012-01-01

    We report the theory and implementation of vibrational coupled cluster (VCC) damped response functions. From the imaginary part of the damped VCC response function the absorption as function of frequency can be obtained, requiring formally the solution of the now complex VCC response equations. T...

  14. Particle Damping with Granular Materials for Multi Degree of Freedom System

    Directory of Open Access Journals (Sweden)

    Masanobu Inoue

    2011-01-01

    Full Text Available A particle damper consists of a bed of granular materials moving in cavities within a multi degree-of-freedom (MDOF structure. This paper deals with the damping effects on forced vibrations of a MDOF structure provided with the vertical particle dampers. In the analysis, the particle bed is assumed to be a single mass, and the collisions between the granules and the cavities are completely inelastic, i.e., all energy dissipation mechanisms are wrapped into zero coefficient of restitution. To predict the particle damping effect, equations of motion are developed in terms of equivalent single degree-of-freedom (SDOF system and damper mass with use made of modal approach. In this report, the periodic vibration model comprising sustained contact on or separation of the damper mass from vibrating structure is developed. A digital model is also formulated to simulate the damped motion of the physical system, taking account of all vibration modes. Numerical and experimental studies are made of the damping performance of plural dampers located at selected positions throughout a 3MDOF system. The experimental results confirm numerical prediction that collision between granules and structures is completely inelastic as the contributing mechanism of damping in the vertical vibration. It is found that particle dampers with properly selected mass ratios and clearances effectively suppress the resonance peaks over a wide frequency range.

  15. Shock reliability enhancement for MEMS vibration energy harvesters with nonlinear air damping as a soft stopper

    Science.gov (United States)

    Chen, Shao-Tuan; Du, Sijun; Arroyo, Emmanuelle; Jia, Yu; Seshia, Ashwin

    2017-10-01

    This paper presents a novel application of utilising nonlinear air damping as a soft mechanical stopper to increase the shock reliability for microelectromechanical systems (MEMS) vibration energy harvesters. The theoretical framework for nonlinear air damping is constructed for MEMS vibration energy harvesters operating in different air pressure levels, and characterisation experiments are conducted to establish the relationship between air pressure and nonlinear air damping coefficient for rectangular cantilever MEMS micro cantilevers with different proof masses. Design guidelines on choosing the optimal air pressure level for different MEMS vibration energy harvesters based on the trade-off between harvestable energy and the device robustness are presented, and random excitation experiments are performed to verify the robustness of MEMS vibration energy harvesters with nonlinear air damping as soft stoppers to limit the maximum deflection distance and increase the shock reliability of the device.

  16. Shear measurements of viscoelastic damping materials embedded in composite plates

    Science.gov (United States)

    Biggerstaff, Janet M.; Kosmatka, John B.

    1999-06-01

    Embedding viscoelastic damping materials into graphite/epoxy composites can greatly increase the damping of composite structures. Cocuring the damping material with the composite, however, has been shown to increase the modulus and lower the damping in many viscoelastic materials because epoxy penetrates many damping materials (especially acrylics). In this paper, the changes in shear modulus were measured using double lap shear tests. Also presented are shear moduli comparisons of samples cured with three different barrier film layers, KaptonR, TedlarR,and polyester, which are used to prevent the epoxy penetration. Lastly, samples with an embedded loosely woven scrim cloth placed between two damping material layers are tested to measure how the scrim affects the shear modulus.

  17. Semi-active on-off damping control of a dynamic vibration absorber using Coriolis force

    Science.gov (United States)

    La, Viet Duc

    2012-07-01

    A passive dynamic vibration absorber (DVA) moving along a pendulum can cause the nonlinear Coriolis damping to reduce the pendulum swing. This paper proposes a simple semi-active on-off damping controller to improve the passive Coriolis DVA. The aim of the on-off damping control is to amplify the DVA resonance motion to increase the energy dissipated. Moreover, the paper finds the analytical solution of the harmonic vibration of semi-active controlled system. The accuracy of the analytical formulas and the superior performance of the semi-active DVA are verified by numerical simulations.

  18. Vibration Damping Response of Composite Materials

    Science.gov (United States)

    1991-04-01

    unidirectional composite panels were made having thicknesses as specified in the ASTM D3039 -76 test procedure. After fabrication, these panels were...established procedures which are typically utilized. Specifically, the ASTM test methodologies were utilized. To determine El, E2, V󈧐, and V21...glass/3501-6, the ASTM D2584-68 Ignition Loss of Cured Reinfoiced Resins test procedure was used. In all cases, the fiber volume fraction was

  19. Vibration absorption in systems with a nonlinear energy sink: Nonlinear damping

    Science.gov (United States)

    Starosvetsky, Y.; Gendelman, O. V.

    2009-07-01

    In this work, response regimes are investigated in a system comprising of a linear oscillator (subject to harmonic excitation) and a nonlinear energy sink (NES) with nonlinear damping characteristics. An analytical technique for the treatment of certain class of nonlinear damping functions is developed. Special attention is paid to the case of piecewise-quadratic damping, motivated by possible applications. It is demonstrated that the NES with a properly tuned piecewise-quadratic damping element allows complete elimination of undesirable periodic regimes. In this way, an efficient system of vibration absorption is obtained, and its performance can overcome that of a tuned mass damper (TMD). Numerical results agree satisfactorily with the analytical predictions.

  20. Vibrational relaxation beyond the linear damping limit in two-dimensional optical spectra of molecular aggregates

    Science.gov (United States)

    Perlík, Václav; Šanda, František

    2017-08-01

    We present a computational model for the spectra of molecular aggregates with signatures of vibronic progression. Vibronic dynamics is implemented by coupling the dynamics of Frenkel excitons with underdamped vibrations. Vibrational dynamics includes linear damping resulting in the exponential decay and quadratic damping inducing subexponential or power law relaxation and increasing vibrational decoherence as demonstrated on lineshapes of the absorption spectrum. Simulations of the third-order coherent response account for bath reorganization during excitonic transport, which allows us to study the line-shape evolution of cross peaks of 2D spectra.

  1. Complex modes and frequencies in damped structural vibrations

    DEFF Research Database (Denmark)

    Krenk, Steen

    2004-01-01

    It is demonstrated that the state space formulation of the equation of motion of damped structural elements like cables and beams leads to a symmetric eigenvalue problem if the stiffness and damping operators are self-adjoint, and that this is typically the case in the absence of gyroscopic force...

  2. Theoretical Modelling and Effectiveness Study of Slotted Stand-Off Layer Damping Treatment for Rail Vibration and Noise Control

    Directory of Open Access Journals (Sweden)

    Caiyou Zhao

    2015-01-01

    Full Text Available A promising means of reducing railway noise is to increase the damping of the rail, which decreases the vibration of the rail to reduce noise. To achieve this goal, a slotted stand-off layer damping treatment has been developed, and a compound track model with this treatment is developed for investigating the effectiveness of this treatment in terms of the vibration reduction. Through the dynamic analysis of the track undergoing the slotted stand-off layer damping treatment, some guidelines are proposed on the selection of materials and structure parameters for this treatment. In addition, the prototype of the optimal slotted stand-off layer damping treatment has been built and tested in the laboratory. It is found that the slotted stand-off damping treatment shows significant effects in decreasing the amplitude of the accelerance of the rail and a significant reduction of sound emission reflected as the radiation sound pressure level decreases by 8.2 and 9.4 dB at vertical excitation and lateral excitation, respectively, in the frequency range of 0–4000 Hz.

  3. Identifying the damping contribution of building components based on measured top vibration

    NARCIS (Netherlands)

    Berg, R.L.J. van den; Steenbergen, R.D.J.M.

    2013-01-01

    In this paper, a damping model for a high-rise building is introduced. This model is used to investigate the possibilities to identify the relative damping contribution of the internal material damping in building elements, energy loss at element interfaces and energy outflow at the interface with

  4. Vibration Analysis of Cylindrical Sandwich Aluminum Shell with Viscoelastic Damping Treatment

    Directory of Open Access Journals (Sweden)

    Tai-Hong Cheng

    2013-01-01

    Full Text Available This paper has applied the constrained viscoelastic layer damping treatments to a cylindrical aluminum shell using layerwise displacement theory. The transverse shear, the normal strains, and the curved geometry are exactly taken into account in the present layerwise shell model, which can depict the zig-zag in-plane and out-of-plane displacements. The damped natural frequencies, modal loss factors, and frequency response functions of cylindrical viscoelastic aluminum shells are compared with those of the base thick aluminum panel without a viscoelastic layer. The thickness and damping ratio of the viscoelastic damping layer, the curvature of proposed cylindrical aluminum structure, and placement of damping layer of the aluminum panel were investigated using frequency response function. The presented results show that the sandwiched viscoelastic damping layer can effectively suppress vibration of cylindrical aluminum structure.

  5. Two methods for damping torsional vibrations in DFIG-based wind generators using power converters

    Science.gov (United States)

    Zhao, Zuyi; Lu, Yupu; Xie, Da; Yu, Songtao; Wu, Wangping

    2017-01-01

    This paper proposes novel damping control algorithms by using static synchronous compensator (STATCOM) and energy storage system (ESS) to damp torsional vibrations in doubly fed induction generator (DFIG) based wind turbine systems. It first analyses the operating characteristics of STATCOM and ESS for regulating power variations to increase grid voltage stability. Then, new control strategies for STATCOM and ESS are introduced to damp the vibrations. It is followed by illustration of their effectiveness to damp the drive train torsional vibrations of wind turbines, which can be caused by grid disturbances, such as voltage sags and frequency fluctuations. Results suggest that STATCOM is a promising technology to mitigate the torsional vibrations caused by grid voltage sags. By contrast, the ESS connected to the point of common coupling (PCC) of wind turbine systems shows even obvious advantages because of its capability of absorbing/releasing both active and reactive power. It can thus be concluded that STATCOM is useful for stabilizing power system voltage fluctuations, and ESS is more effective both in regulating PCC voltage fluctuations and damping torsional vibrations caused by grid voltage frequency fluctuations.

  6. Fractal Theory and Contact Dynamics Modeling Vibration Characteristics of Damping Blade

    Directory of Open Access Journals (Sweden)

    Ruishan Yuan

    2014-01-01

    Full Text Available The contact surface structure of dry friction damper is complicate, irregular, and self-similar. In this paper, contact surface structure is described with the fractal theory and damping blade is simplified as 2-DOF cantilever beam model with lumped masses. By changing the position of the damper, lacing and shroud structure are separately simulated to study vibration absorption effect of damping blade. The results show that both shroud structure and lacing could not only dissipate energy but also change stiffness of blade. Under the same condition of normal pressure and contact surface, the damping effect of lacing is stronger than that of shroud structure. Meanwhile, the effect on changing blade stiffness of shroud structure is stronger than that of lacing. This paper proposed that there is at least one position of the blade, at which the damper dissipates the most vibration energy during a vibration cycle.

  7. Passive damping concepts for free and forced member and grillage vibration

    Science.gov (United States)

    Razzaq, Zia; Najjar, Bassam

    1988-01-01

    The performance of potential passive damping concepts is investigted for a long tubular aluminum alloy member, and a two-bar grillage structure. The members are restrained partially at the ends and are of the type being considered by NASA for possible use in the construction of a future space station. Four different passive damping concepts are studied and include nylon brush, wool swab, copper brush, and silly putty in chamber dampers. Both free and forced vibration tests are conducted. It is found that the silly putty in chamber damper concept provides considerably greater passive damping as compared to that of the other three concepts. For the grillage natural vibration, a five wool swab damper configuration provides greater damping than the five silly putty dampers in chamber configuration. Due to the constrained motion imposed by the vibrator used in the tests, the effectiveness of the passive dampers could not be adequately evaluated for the individual member. However, it is found that for the grillage under forced vibration, the five silly putty dampers in chamber damper configuration provides very effective passive damping although only at and around the resonant frequency. At resonance, these dampers provide a 51 percent reduction in the dynamic magnification factor for this case.

  8. Evaluation of damping estimates by automated Operational Modal Analysis for offshore wind turbine tower vibrations

    DEFF Research Database (Denmark)

    Bajrić, Anela; Høgsberg, Jan Becker; Rüdinger, Finn

    2018-01-01

    Reliable predictions of the lifetime of offshore wind turbine structures are influenced by the limited knowledge concerning the inherent level of damping during downtime. Error measures and an automated procedure for covariance driven Operational Modal Analysis (OMA) techniques has been proposed...... techniques are discussed and illustrated with respect to signal noise, measurement time, vibration amplitudes and stationarity of the ambient response. The best bias-variance error trade-off of damping estimates is obtained by the COV-SSI. The proposed automated procedure is validated by real vibration...

  9. Vibrations of stretched damped beams under non-ideal boundary ...

    Indian Academy of Sciences (India)

    Stretched beam vibrations; non-ideal boundary conditions; method of multiple time scales. 1. Introduction. Beams are frequently used as design models for vibration analysis. In such analysis, types of support conditions are important and have direct effect on the solutions and natural fre- quencies. Different types of supports ...

  10. Vibrations of stretched damped beams under non-ideal boundary ...

    Indian Academy of Sciences (India)

    A simply supported damped Euler–Bernoulli beam with immovable end conditions are considered. The concept of non-ideal boundary conditions is applied to the beam problem. In accordance, the boundaries are assumed to allow small deflections and moments. Approximate analytical solution of the problem is found ...

  11. Nonlinear modeling of tuned liquid dampers (TLDs) in rotating wind turbine blades for damping edgewise vibrations

    DEFF Research Database (Denmark)

    Zhang, Zili; Nielsen, Søren R. K.; Basu, Biswajit

    2015-01-01

    Tuned liquid dampers (TLDs) utilize the sloshing motion of the fluid to suppress structural vibrations and become a natural candidate for damping vibrations in rotating wind turbine blades. The centrifugal acceleration at the tip of a wind turbine blade can reach a magnitude of 7–8g. This facilit......Tuned liquid dampers (TLDs) utilize the sloshing motion of the fluid to suppress structural vibrations and become a natural candidate for damping vibrations in rotating wind turbine blades. The centrifugal acceleration at the tip of a wind turbine blade can reach a magnitude of 7–8g...... free-surface elevation equally well, the one-mode model can still be utilized for the design of TLD. Parametric optimization of the TLD is carried out based on the one-mode model, and the optimized damper effectively improves the dynamic response of wind turbine blades....

  12. Comparison of vibration damping of standard and PDCPD housing of the electric power steering system

    Science.gov (United States)

    Płaczek, M.; Wróbel, A.; Baier, A.

    2017-08-01

    A comparison of two different types of electric power steering system housing is presented. The first considered type of the housing was a standard one that is made of an aluminium alloy. The second one is made of polydicyclopentadiene polymer (PDCPD) and was produced using the RIM technology. Considered elements were analysed in order to verify their properties of vibrations damping. This property is very important taking into account noise generated by elements of a car’s power steering system. During the carried out tests vibrations of analysed power steering housings were measured using Marco Fiber Composite (MFC) piezoelectric transducers. Results obtained for both considered power steering housings in case of the same parameters of vibrations excitations were measured and juxtaposed. Obtained results were analysed in order to verify if the housing made of PDCPD polymer has better properties of vibration damping than the standard one.

  13. Optimization of constrained layer damping for strain energy minimization of vibrating pads

    Directory of Open Access Journals (Sweden)

    Supachai Lakkam1

    2012-04-01

    Full Text Available An optimization study for brake squeals aims to minimize the strain energy of vibrating pads with constrained layerdamping. To achieve this, using finite element method and experiments were operated and assumed-coupling mode methodwas used to solve it. The integrated global strain energy of the pad over a frequency range of interesting mode was calculated.Parametric studies were then performed to identify those dominant parameters on the vibration response of the damped pad.Moreover, the proposed methodology was employed to search for the optimum of the position/geometry of the constrainedlayer damping patch. Optimal solutions are given and discussed for different cases where the strain energy of the pad over afrequency range is covering the first bending mode and with the inclusion of the restriction of minimum damping materialutilization. As a result, the integrated strain energy is then performed to identify and optimize the position and geometry of thedamping shim. The optimization of the constrained layer damping for strain energy minimization of vibrating pads depend onthe position of the shape of the damping patch. These data can guide to specify the position of the constrained layer dampingpatch under pressure conditions.

  14. Graphite/Polyurethane Flexible Composites - Mechanical and Vibration Damping Properties

    Science.gov (United States)

    1993-07-01

    with an accelerometer. The damping loss factor is determined using either the half power point method or the reverberation time method. Details of the... time and half power point m -.hods. It should be noted that both techniques show similar results with the reverberation time method results less than 10...lower than the half power point method. The reverberation time method results are probably more accurate due to the errors associated in the half

  15. Vibroacoustic Optimization of Stiffening Ribs and Damping Material Distribution on Sheet Metal Parts

    Directory of Open Access Journals (Sweden)

    M. Carfagni

    2004-01-01

    Full Text Available Vehicle noise and vibration levels are basic parameters in passenger comfort. Both static and dynamic stiffness of sheet metal parts is commonly increased by means of stiffening ribs. Vibrations are also reduced by adding a layer of damping material on the floor, the roof, the firewall and other parts of the vehicle. In common practice the panels to be treated are ribbed according to criteria based on the designer’s experience, rather than on well defined design procedures and are uniformly covered by a layer of damping material. However, these are not efficient design solutions, especially with regard to the effectiveness of vibration reduction and to weight containment. In this paper a novel approach to achieve an optimal distribution of stiffening ribs and damping material will be presented. The proposed method is based on a Genetic Algorithm (G.A. procedure which takes into account both the vibroacoustic performance and the weight and cost reduction. A simple case study will be illustrated to demonstrate the capabilities of the developed procedure.

  16. Experimental investigation of damping for edgewise blade vibrations; Eksperimentel bestemmelse af daempning for kantsvingninger

    Energy Technology Data Exchange (ETDEWEB)

    Thomsen, K.; Thirstrup Petersen, J. [Forskningscenter Risoe (Denmark); Nim, E. [Bonus Energy A/S (Denmark); Oeye, S. [Danmarks Tekniske Univ. (Denmark); Pedersen, B. [LM Glasfiber A/S (Denmark)

    2000-01-01

    The main result of the investigation is a newly developed method to identify the effective damping for the edgewise blade mode shape for wind turbines. The method consists of an exciter mechanism which makes it possible to excite the edgewise blade mode shapes from the wind turbine nacelle and furthermore of an analysis method, which enables a straightforward determination of the damping. The analysis method is based on a local blade whirl description of the edgewise blade vibrations. The method is verified on a Bonus wind turbine and for this specific turbine the effective damping for edgewise blade vibrations has been determined. The results have been compared with aeroelastic simulations. The potential of the method is that the results can support the further development of aeroelastic models and fine tuning of parameters of importance of the edgewise blade vibration problem and thus improve the certainty in the predicted risk of vibrations. Furthermore, the method can be used for experimental investigation of the risk of edgewise blade vibrations for a specific turbine. (au)

  17. Maximum mistuning amplification of the forced response vibration of turbomachinery rotors in the presence of aerodynamic damping

    Science.gov (United States)

    Martel, Carlos; Sánchez-Álvarez, J. J.

    2017-06-01

    Mistuning can dangerously increase the vibration amplitude of the forced response of a turbomachinery rotor. In the case of damping coming from aerodynamic effects the situation is more complicated because the magnitude of the damping changes for the different travelling wave modes of the system. This damping variability modifies the effect of mistuning, and it can even result in a reduction of the mistuned forced response amplitude below that of the tuned case (this is not possible in the usual case of constant material damping). In this paper the Asymptotic Mistuning Model (AMM) methodology is used to analyze this situation. The AMM is a reduced order model that is systematically derived from the mistuned bladed disk full model using a perturbative procedure based on the small size of the mistuning and the damping. The AMM allows to derive a very simple expression for an upper bound of the maximum amplification factor of the vibration amplitude that the system can experience (an extension of the well known Whitehead 1966 result to include the effect of non-uniform aerodamping). This new upper bound gives information on the mechanisms involved in the amplification/reduction of the mistuned response: (i) the number of modes participating in the response, and (ii) the ratio between the aerodamping of the directly forced mode and that of the of the rest of the modes. A FEM of a mistuned bladed disk is also used to verify the AMM predictions for several different forcing configurations, and both results show a very good quantitative agreement.

  18. Universal damping mechanism of quantum vibrations in deep sub-barrier fusion reactions

    Science.gov (United States)

    Ichikawa, Takatoshi

    2017-11-01

    I demonstrate that the coordinate dependence of the coupling strengths of colliding nuclei is important for describing the deep sub-barrier fusion hindrance. To this end, I firstly show the performance of an extended coupled-channel model by phenomenologically introducing a damping factor in the coupling potential. The damping factor stimulates the damping of quantum vibrations occurring near the touching point of colliding nuclei and introduce a coordinate dependence in the coupling strengths. Next, I directly show the coordinate dependence of the transition strengths of colliding nuclei by microscopically calculating excited states using the random phase approximation method. The obtained transition strengths of colliding nuclei as a function of the center-of-mass distance strongly correlate with the damping factor that reproduces very well the fusion hindrance. This is a direct justification for the concept of the coordinate-dependent coupling strengths. Finally, I conclude that the damping of quantum vibrations near the touching point is the universal mechanism for the deep sub-barrier fusion hindrance.

  19. Numerical Investigation of Damping of Torsional Beam Vibrations by Viscous Bimoments

    DEFF Research Database (Denmark)

    Hoffmeyer, David; Høgsberg, Jan Becker

    2017-01-01

    Damping of torsional beam vibrations of slender beam–structures with thin–walled cross–sections is investigated. Analytical results from solving the differential equation governing torsion with viscous bimoments imposed at the boundary, are compared with a numerical approach with three......–dimensional, is oparametric elements. The viscous bimoments act on the axial warping displacements associated with in homogeneous torsion, and are in a numerical format realized by suitable configurations of concentrated, axial forces describing discrete dampers.It is illustrated by an example that significant damping ratios...

  20. Smart earthquake-resistant materials: using time-released adhesives for damping, stiffening, and deflection control

    Science.gov (United States)

    Dry, Carolyn M.

    1996-04-01

    Preventing buildings and bridges from damage from severe dynamic loading events is a primary goal of civil infrastructure. Present designs attempt to control structural response by making the structures more massive, by increasing lateral stiffness through bracing, and by damping technology such as mass damping and base-isolation. These attempts affect portions of the governing equation: for an idealized building frame or bridge, the free vibrational behavior is described by Mu + cu + ku equals -mug(t) where m equals mass, c equals damping coefficient, k equals lateral stiffness, u equals deflection, and ug(t) equals ground acceleration. The use of adhesive released internally in a material based way of addressing the problem. The time release of low modulus adhesive chemicals would assist the damping characteristics of the structure, use of a stiffer adhesive would allow the damaged structure to regain some lateral stiffness (k) and adjustment of the set times of the adhesives would act to control the deflection. These can be thought of as potential new method of controlling vibration of behavior in case of a dynamic loading event. In past experiments, self-healing concrete matrices were shown to increase post-yield deflection and load carrying capability by the release and setting of adhesives. The results were promising in resisting damage of dynamic loads applied to frames. This indicates that self-healing concrete would be extremely valuable in civil engineering structures that were subjected to failure-inducing loads such as earthquakes.

  1. A procedure to estimate the dynamic damped behavior of fiber reinforced composite beams submitted to flexural vibrations

    Directory of Open Access Journals (Sweden)

    Volnei Tita

    2001-10-01

    Full Text Available This work proposes a procedure to estimate the dynamic damped behavior of fiber reinforced composite beams in flexural vibrations. A set of experimental dynamic tests were carried out in order to investigate the natural frequencies and modal shapes. These results are used to evaluate the damping factors by the program FREQ. These damping factors are then used as input to a damped dynamic analysis by the Finite Element Method, using Rayleigh Model. A good agreement between theoretical and experimental results was obtained. Thus, it became possible to validate the proposed procedure to evaluate dynamic damped behavior of composite beams.

  2. MODELING INFLUENCE OF ROLLING BEARING BUSH AND VIBRATION DAMPING IN CATCHING OF TOOTHED WHEELS

    Directory of Open Access Journals (Sweden)

    P. V. Diachenko

    2010-11-01

    Full Text Available On the base of dynamic scheme of toothing, a mathematical model for study of the influence of constructive parameters of radial bearings such as a factor of friction, reduced masses and stiffnesses on damping the vibrations in gearing is developed. The solution for the model is obtained using a simulation modeling in the Simulink environment with checking the validity of results in the system MathCad. The oscillograms of the vibrations under investigation and the conclusions on the base of their analysis are presented.

  3. Design of three-element dynamic vibration absorber for damped linear structures

    Science.gov (United States)

    Anh, N. D.; Nguyen, N. X.; Hoa, L. T.

    2013-09-01

    The standard type of dynamic vibration absorber (DVA) called the Voigt DVA is a classical model and has long been investigated. In the paper, we will consider an optimization problem of another model of DVA that is called three-element type DVA for damped primary structures. Unlike the standard absorber configuration, the three-element DVA contains two spring elements in which one is connected to a dashpot in series and the other is placed in parallel. There have been some studies on the design of the three-element DVA for undamped primary structures. Those studies have shown that the three-element DVA produces better performance than the Voigt DVA does. When damping is present at the primary system, to the best knowledge of the authors, there has been no study on the three-element dynamic vibration absorber. This work presents a simple approach to determine the approximate analytical solutions for the H∞ optimization of the three-element DVA attached to the damped primary structure. The main idea of the study is based on the criteria of the equivalent linearization method in order to replace approximately the original damped structure by an equivalent undamped one. Then the approximate analytical solution of the DVA's parameters is given by using known results for the undamped structure obtained. The comparisons have been done to verify the effectiveness of the obtained results.

  4. Investigations on Elastic and Damping Characteristics of Vibration Isolation Systems While Using Factor Experiment

    Directory of Open Access Journals (Sweden)

    G. N. Reysina

    2014-01-01

    Full Text Available The paper presents results of the investigations on elastic and damping characteristics of a vibration isolation system. Adequate mathematical models of relative root-mean-square values for acceleration of antivibration mass have been obtained depending on elastic and viscous constituents. The paper  reveals  that the proposed method of multiple correlation is the most rational one for the analysis of power  fluids used in the electro-rheological dampers.

  5. Resonant ultrasound spectroscopy for materials with high damping and samples of arbitrary geometry

    Science.gov (United States)

    Remillieux, Marcel C.; Ulrich, T. J.; Payan, Cédric; Rivière, Jacques; Lake, Colton R.; Le Bas, Pierre-Yves

    2015-07-01

    Resonant ultrasound spectroscopy (RUS) is a powerful and established technique for measuring elastic constants of a material with general anisotropy. The first step of this technique consists of extracting resonance frequencies and damping from the vibrational frequency spectrum measured on a sample with free boundary conditions. An inversion technique is then used to retrieve the elastic tensor from the measured resonance frequencies. As originally developed, RUS has been mostly applicable to (i) materials with small damping such that the resonances of the sample are well separated and (ii) samples with simple geometries for which analytical solutions exist. In this paper, these limitations are addressed with a new RUS approach adapted to materials with high damping and samples of arbitrary geometry. Resonances are extracted by fitting a sum of exponentially damped sinusoids to the measured frequency spectrum. The inversion of the elastic tensor is achieved with a genetic algorithm, which allows searching for a global minimum within a discrete and relatively wide solution space. First, the accuracy of the proposed approach is evaluated against numerical data simulated for samples with isotropic symmetry and transversely isotropic symmetry. Subsequently, the applicability of the approach is demonstrated using experimental data collected on a composite structure consisting of a cylindrical sample of Berea sandstone glued to a large piezoelectric disk. In the proposed experiments, RUS is further enhanced by the use of a 3-D laser vibrometer allowing the visualization of most of the modes in the frequency band studied.

  6. Tire stiffness and damping determined from static and free-vibration tests. [aircraft tires

    Science.gov (United States)

    Sleeper, R. K.; Dreher, R. C.

    1980-01-01

    Stiffness and damping of a nonrolling tire were determined experimentally from both static force-displacement relations and the free-vibration behavior of a cable-suspended platen pressed against the tire periphery. Lateral and force-and-aft spring constants and damping factors of a 49 x 17 size aircraft tire for different tire pressure and vertical loads were measured assuming a rate-independent damping form. In addition, a technique was applied for estimating the magnitude of the tire mass which participates in the vibratory motion of the dynamic tests. Results show that both the lateral and force-and-aft spring constants generally increase with tire pressure but only the latter increased significantly with vertical tire loading. The fore-and-aft spring constants were greater than those in the lateral direction. The static-spring-constant variations were similar to the dynamic variations but exhibited lower magnitudes. Damping was small and insensitive to tire loading. Furthermore, static damping accounted for a significant portion of that found dynamically. Effective tire masses were also small.

  7. Damping insert materials for settling chambers of supersonic wind tunnels

    Science.gov (United States)

    Wu, Jie; Radespiel, Rolf

    2017-03-01

    This study describes the application of a novel damping insert material for reducing the flow fluctuations in a tandem nozzle supersonic wind tunnel. This new damping material is composed of multi-layer stainless steel wired meshes. The influences of the multi-layer mesh, such as the quantity of the mesh layer and the installed location in the settling chamber, to the freestream quality have been investigated. A Pitot probe instrumented with a Kulite pressure sensor and a hot-wire probe are employed to monitor the flow fluctuation in the test section of the wind tunnel. Thereafter, a combined modal analysis is applied for the disturbance qualification. Additionally, the transient Mach number in the test section is measured. The disturbance qualification indicates that the multi-layer mesh performs well in providing reduction of vorticity reduction and acoustic fluctuations. Comparable flow quality of the freestream was also obtained using a combination of flexible damping materials. However, the life-span of the new damping materials is much longer. The time transient of the Mach number measured in the test section indicates that the mean flow is rather constant over run time. Furthermore, the time-averaged pressure along the settling chamber is recorded and it shows the distribution of pressure drop by settling chamber inserts.

  8. Natural Frequencies and Modal Damping Ratios Identification of Civil Structures from Ambient Vibration Data

    Directory of Open Access Journals (Sweden)

    Minh-Nghi Ta

    2006-01-01

    Full Text Available Damping is a mechanism that dissipates vibration energy in dynamic systems and plays a key role in dynamic response prediction, vibration control as well as in structural health monitoring during service. In this paper a time domain and a time-scale domain approaches are used for damping estimation of engineering structures, using ambient response data only. The use of tests under ambient vibration is increasingly popular today because they allow to measure the structural response in service. In this paper we consider two engineering structures excited by ambient forces. The first structure is the 310 m tall TV tower recently constructed in the city of Nanjing in China. The second example concerns the Jinma cable-stayed bridge that connects Guangzhou and Zhaoqing in China. It is a single tower, double row cable-stayed bridge supported by 112 stay cables. Ambient vibration of each cable is carried out using accelerometers. From output data only, the modal parameter are extracted using a subspace method and the wavelet transform method.

  9. Study on Forced Torsional Vibration of CFRP Drive-Line System with Internal Damping

    Science.gov (United States)

    Yang, Mo; Hu, Yefa; Zhang, Jinguang; Ding, Guoping; Song, Chunsheng

    2017-12-01

    The use of CFRP transmission shaft has positive effect on the weight and flexural vibration reduction of drive-line system. However, the application of CFRP transmission shaft will greatly reduce the torsional stiffness of the drive-line, and may cause strong transient torsional vibration. Which will seriously affect the performance of CFRP drive-line. In this study, the forced torsional vibration of the CFRP drive-line system is carried out using the lumped parameter model. In addition, the effect of rotary inertia, internal damping, coupling due to the composite laminate, and excitation torque are incorporated in the modified transfer matrix model (TMM). Then, the modified TMM is used to predict the torsional frequency and forced torsional vibration of a CFRP drive-line with three-segment drive shafts. The results of modified TMM shown that the rotational speed difference of the CFRP transmission shaft segment is much larger than metal transmission shaft segment under excitation torque. And compared the results from finite element simulation, modified TMM and torsional vibration experiment respectively, and it has shown that the modified TMM can accurately predict forced torsional vibration behaviors of the CFRP drive-line system.

  10. Design, Fabrication, and Properties of High Damping Metal Matrix Composites?A Review

    OpenAIRE

    Qianfeng Fang; Zhijun Cheng; Tao Zhang; Xianping Wang; Hui Lu

    2009-01-01

    Nowadays it is commonly considered that high damping materials which have both the good mechanical properties as structural materials and the high damping capacity for vibration damping are the most direct vibration damping solution. In metals and alloys however, exhibiting simultaneously high damping capacity and good mechanical properties has been noted to be normally incompatible because the microscopic mechanisms responsible for internal friction (namely damping capacity) are dependent up...

  11. System and method for damping vibration in a drill string using a magnetorheological damper

    Science.gov (United States)

    Wassell, Mark Ellsworth [Houston, TX; Burgess, Daniel E [Portland, CT; Barbely, Jason R [East Islip, NY

    2012-01-03

    A system for damping vibration in a drill string can include a magnetorheological fluid valve assembly having a supply of a magnetorheological fluid, a first member, and a second member capable of moving in relation to first member in response to vibration of the drill bit. The first and second members define a first and a second chamber for holding the fluid. Fluid can flow between the first and second chambers in response to the movement of the second member in relation to the first member. The valve assembly can also include a coil for inducing a magnetic field that alters the resistance of the magnetorheological fluid to flow between the first and second chambers, thereby increasing the damping provided by the valve. A remnant magnetic field is induced in one or more components of the magnetorheological fluid valve during operation that can be used to provide the magnetic field for operating the valve so as to eliminate the need to energize the coils during operation except temporarily when changing the amount of damping required, thereby eliminating the need for a turbine alternator power the magnetorheological fluid valve. A demagnetization cycle can be used to reduce the remnant magnetic field when necessary.

  12. DAMPE

    CERN Multimedia

    Chen, D

    The $\\textbf{DA}$rk $\\textbf{M}$atter $\\textbf{P}$article $\\textbf{E}$xplorer (DAMPE) experiment is a high-energy astroparticle physics satellite mission to search for Dark Matter signatures in space, study the cosmic ray spectrum and composition up to 100 TeV, and perform high-energy gamma astronomy. The launch is planned for end 2015, initially for 3 years, to compliment existing space missions FERMI, AMS and CALET.

  13. Experimental Study on Dry Friction Damping Characteristics of the Steam Turbine Blade Material with Nonconforming Contacts

    Directory of Open Access Journals (Sweden)

    Jun Wu

    2015-01-01

    Full Text Available An experiment system has been established to study the dry friction damping dynamic characteristics of the steam turbine blade material 1Cr13. The friction dynamic characteristics of the specimens with nonconforming contact surfaces are measured under different parameters. The experiment results are compared with that of the macroslip hysteresis model and the Mindlin microslip friction model in detail. The results show that the experimental result of the tangential contact stiffness is in good agreement with that of the theory result based on the fractal theory and the Hertz contact theory by Jiang et al., 2009. The dimensionless equivalent stiffness and equivalent damping obtained by the macroslip hysteresis model agree well with the experimental results when relative motion is relatively large. However, the results of the macroslip hysteresis model differ a lot from the experimental results when relative motion is relatively small. Compared with the macroslip hysteresis model, the Mindlin microslip friction model can predict the dimensionless equivalent stiffness and equivalent damping accurately during the whole measurement range. The linear regularities of dimensionless equivalent stiffness and equivalent damping are obtained, which decrease the difficulty of building the vibration analysis model of the blade with sufficient accuracy.

  14. Dynamics of vibration isolation system with rubber-cord-pneumatic spring with damping throttle

    Science.gov (United States)

    Burian, Yu A.; Silkov, M. V.

    2017-06-01

    The study refers to the important area of applied mechanics; it is the theory of vibration isolation of vibroactive facilities. The design and the issues of mathematical modeling of pneumatic spring perspective design made on the basis of rubber-cord shell with additional volume connected with its primary volume by means of throttle passageway are considered in the text. Damping at the overflow of air through the hole limits the amplitude of oscillation at resonance. But in contrast to conventional systems with viscous damping it does not increase transmission ratio at high frequencies. The mathematical model of suspension allowing selecting options to reduce the power transmission ratio on the foundation, especially in the high frequency range is obtained

  15. Importance of Added Mass and Damping in Flow-Induced Vibration Analysis of Tubes Bundle: An Overview

    Directory of Open Access Journals (Sweden)

    Faisal Karim Shami

    2012-01-01

    Full Text Available Flow-induced vibration is of prime concern to the designers of heat exchangers subjected to high flows of gases or liquids. Excessive vibration may cause tube failure due to fatigue or fretting-wear. Tube failure results in, expensive plant upholding and suffers loss of production. Therefore, tube failure due to unwarranted vibration must be avoided in process heat exchangers and nuclear steam generators, preferably at design stage. Such vibration problems may be avoided through a comprehensive flowinduced vibration analysis before fabrication of heat exchangers. However, it requires an understanding of vibration mechanism and parameters related to flow-induced vibration. For an accurate vibration analysis, it is of prime importance to have good estimates of structural and flow related dynamic parameters. Thus dynamic parameters such as added mass and damping are of significant concern in a flow regime. The purpose of this paper is to provide an overview of our state of knowledge and role of dynamic parameters in flow-induced vibration on tube bundles due to current trend of larger heat exchangers. The present paper provides published data, analysis, evaluation, formulation, and experimental studies related to hydrodynamic mass and damping by a large number of researchers. Guidelines for experimental research and heat exchangers design related to added mass and damping mechanisms subjected to both single and two-phase flow are outlined in this paper.

  16. Semi-active damping with negative stiffness for multi-mode cable vibration mitigation: approximate collocated control solution

    Science.gov (United States)

    Weber, F.; Distl, H.

    2015-11-01

    This paper derives an approximate collocated control solution for the mitigation of multi-mode cable vibration by semi-active damping with negative stiffness based on the control force characteristics of clipped linear quadratic regulator (LQR). The control parameters are derived from optimal modal viscous damping and corrected in order to guarantee that both the equivalent viscous damping coefficient and the equivalent stiffness coefficient of the semi-active cable damper force are equal to their desired counterparts. The collocated control solution with corrected control parameters is numerically validated by free decay tests of the first four cable modes and combinations of these modes. The results of the single-harmonic tests demonstrate that the novel approach yields 1.86 times more cable damping than optimal modal viscous damping and 1.87 to 2.33 times more damping compared to a passive oil damper whose viscous damper coefficient is optimally tuned to the targeted mode range of the first four modes. The improvement in case of the multi-harmonic vibration tests, i.e. when modes 1 and 3 and modes 2 and 4 are vibrating at the same time, is between 1.55 and 3.81. The results also show that these improvements are obtained almost independent of the cable anti-node amplitude. Thus, the proposed approximate real-time applicable collocated semi-active control solution which can be realized by magnetorheological dampers represents a promising tool for the efficient mitigation of stay cable vibrations.

  17. Characterization of viscoelastic response and damping of composite materials used in flywheel rotors

    Science.gov (United States)

    Chen, Jianmin

    The long-term goal for spacecraft flywheel systems with higher energy density at the system level requires new and innovative composite material concepts. Multi-Direction Composite (MDC) offers significant advantages over traditional filament-wound and multi-ring press-fit filament-wound wheels in providing higher energy density (i.e., less mass), better crack resistance, and enhanced safety. However there is a lack of systematic characterization for dynamic properties of MDC composite materials. In order to improve the flywheel materials reliability, durability and life time, it is very important to evaluate the time dependent aging effects and damping properties of MDC material, which are significant dynamic parameter for vibration and sound control, fatigue endurance, and impact resistance. The physical aging effects are quantified based on a set of creep curves measured at different aging time or different aging temperature. One parameter (tau) curve fit was proposed to represent the relationship of aging time and aging temperature between different master curves. The long term mechanical behavior was predicted by obtained master curves. The time and temperature shift factors of matrix were obtained from creep curves and the aging time shift rate were calculated. The aging effects on composite are obtained from experiments and compared with prediction. The mechanical quasi-behavior of MDC composite was analyzed. The correspondence principle was used to relate quasi-static elastic properties of composite materials to time-dependent properties of its constituent materials (i.e., fiber and matrix). The Prony series combined with the multi-data fitting method was applied to inverse Laplace transform and to calculate the time dependent stiffness matrix effectively. Accelerated time-dependent deformation of two flywheel rim designs were studied for a period equivalent to 31 years and are compared with hoop reinforcement only composite. Damping of pure resin and T700

  18. Removing damped sinusoidal vibrations in adaptive optics systems using a DFT-based estimation method

    Science.gov (United States)

    Kania, Dariusz

    2017-06-01

    The problem of a vibrations rejection in adaptive optics systems is still present in publications. These undesirable signals emerge because of shaking the system structure, the tracking process, etc., and they usually are damped sinusoidal signals. There are some mechanical solutions to reduce the signals but they are not very effective. One of software solutions are very popular adaptive methods. An AVC (Adaptive Vibration Cancellation) method has been presented and developed in recent years. The method is based on the estimation of three vibrations parameters and values of frequency, amplitude and phase are essential to produce and adjust a proper signal to reduce or eliminate vibrations signals. This paper presents a fast (below 10 ms) and accurate estimation method of frequency, amplitude and phase of a multifrequency signal that can be used in the AVC method to increase the AO system performance. The method accuracy depends on several parameters: CiR - number of signal periods in a measurement window, N - number of samples in the FFT procedure, H - time window order, SNR, THD, b - number of A/D converter bits in a real time system, γ - the damping ratio of the tested signal, φ - the phase of the tested signal. Systematic errors increase when N, CiR, H decrease and when γ increases. The value of systematic error for γ = 0.1%, CiR = 1.1 and N = 32 is approximately 10^-4 Hz/Hz. This paper focuses on systematic errors of and effect of the signal phase and values of γ on the results.

  19. Dynamic damping of vibrations of technical object with two degrees of freedom

    Science.gov (United States)

    Khomenko, A. P.; Eliseev, S. V.; Artyunin, A. I.

    2017-10-01

    Approach to the solution of problems of dynamic damping for the technical object with two degrees of freedom on the elastic supports is developed. Such tasks are typical for the dynamics of technological vibrating machines, machining machine tools and vehicles. The purpose of the study is to justify the possibility of obtaining regimes of simultaneous dynamic damping of oscillations in two coordinates. The achievement of the goal is based on the use of special devices for the transformation of motion, introduced parallel to the elastic element. The dynamic effect is provided by the possibility of changing the relationships between the reduced masses of devices for transforming motion. The method of structural mathematical modeling is used, in which the mechanical oscillatory system is compared, taking into account the principle of dynamic analogies, the dynamically equivalent structural diagram of the automatic control system. The concept of transfer functions of systems interpartial relations and generalized ideas about the partial frequencies and frequencies dynamic damping is applied. The concept of a frequency diagram that determines the mutual distribution of graphs of frequency characteristics in the interaction of the elements of the system is introduced.

  20. Design Optimization for Vibration Reduction of Viscoelastic Damped Structures Using Genetic Algorithms

    Directory of Open Access Journals (Sweden)

    Zhengchao Xie

    2009-01-01

    Full Text Available Due to the large number of design variables that can be present in complex systems incorporating visco-elastic damping, this work examines the application of genetic algorithms in optimizing the response of these structures. To demonstrate the applicability of genetic algorithms (GAs, the approach is applied to a simple viscoelastically damped constrained-layer beam. To that end, a finite element model (FEM derived by Zapfe, which was based on Rao's formulation, was used for a beam with constrained-layer damping. Then, a genetic algorithm is applied to simultaneously determine the thicknesses of the viscoelastic damping layer and the constraining layer that provide the best response. While the targeted response is ultimately at the discretion of the designer, a few different choices for the fitness function are shown along with their corresponding impact on the vibratory response. By integrating the FEM code within the GA routine, it is easier to include the frequency-dependence of both the shear modulus and the loss factors for the viscoelastic layer. Examples are provided to demonstrate the capabilities of the method. It is shown that while a multi-mode optimization target provides significant reductions, the response for that configuration is inferior to the response when only single-mode reduction is considered. The results also reveal that the optimum configuration has a lower response level than when a thick layer of damping material is used. By demonstrating the applicability of GA for a simple beam structure, the approach can be extended to more complex damped structures.

  1. GOES-R Active Vibration Damping Controller Design, Implementation, and On-Orbit Performance

    Science.gov (United States)

    Clapp, Brian R.; Weigl, Harald J.; Goodzeit, Neil E.; Carter, Delano R.; Rood, Timothy J.

    2017-01-01

    GOES-R series spacecraft feature a number of flexible appendages with modal frequencies below 3.0 Hz which, if excited by spacecraft disturbances, can be sources of undesirable jitter perturbing spacecraft pointing. In order to meet GOES-R pointing stability requirements, the spacecraft flight software implements an Active Vibration Damping (AVD) rate control law which acts in parallel with the nadir point attitude control law. The AVD controller commands spacecraft reaction wheel actuators based upon Inertial Measurement Unit (IMU) inputs to provide additional damping for spacecraft structural modes below 3.0 Hz which vary with solar wing angle. A GOES-R spacecraft dynamics and attitude control system identified model is constructed from pseudo-random reaction wheel torque commands and IMU angular rate response measurements occurring over a single orbit during spacecraft post-deployment activities. The identified Fourier model is computed on the ground, uplinked to the spacecraft flight computer, and the AVD controller filter coefficients are periodically computed on-board from the Fourier model. Consequently, the AVD controller formulation is based not upon pre-launch simulation model estimates but upon on-orbit nadir point attitude control and time-varying spacecraft dynamics. GOES-R high-fidelity time domain simulation results herein demonstrate the accuracy of the AVD identified Fourier model relative to the pre-launch spacecraft dynamics and control truth model. The AVD controller on-board the GOES-16 spacecraft achieves more than a ten-fold increase in structural mode damping of the fundamental solar wing mode while maintaining controller stability margins and ensuring that the nadir point attitude control bandwidth does not fall below 0.02 Hz. On-orbit GOES-16 spacecraft appendage modal frequencies and damping ratios are quantified based upon the AVD system identification, and the increase in modal damping provided by the AVD controller for each structural

  2. Plastic Behavior of Metallic Damping Materials under Cyclical Shear Loading

    Directory of Open Access Journals (Sweden)

    Chaofeng Zhang

    2016-06-01

    Full Text Available Metallic shear panel dampers (SPDs have been widely adopted in seismic engineering. In this study, axial and torsional specimens of four types of metallic damping materials, including three conventional metallic steels as well as low yield strength steel 160 (LYS160, were tested in order to investigate the material response under repeated large plastic strain and low cycle fatigue between 10 and 30 cycles. The present study demonstrated that both the deformation capacity and fatigue performance of LYS160 were underestimated by the conversion from the traditional uniaxial tensile test. The main difference in the failure mechanism between LYS160 and the three conventional materials was determined from the scanning electron microscopy data. The dominant failure mode in LYS160 is stable interlaminate slip and not bucking. Our results provide physical insights into the origin of the large deformation capacity, which is an important foundation for the lightweight design of SPDs.

  3. The Shock Vibration Bulletin. Part 3. Isolation and Damping, Vibration Test Criteria, and Vibration Analysis and Test

    Science.gov (United States)

    1987-01-01

    fatigae equivalent test time of 45-mimates. 1. BACKGROUND subjected to both vibration and loose cargo testing as well an the type and amount of...Environmental Test the track laying environment. Nethods, 10 March 1975. 8. FUTURE EFFORTS 11. Soci, Darrell F., Fatigae Life Estimation Techniques, Technical

  4. Active tuned mass damper for damping of offshore wind turbine vibrations

    DEFF Research Database (Denmark)

    Brodersen, Mark Laier; Bjørke, Ann-Sofie; Høgsberg, Jan Becker

    2017-01-01

    An active tuned mass damper (ATMD) is employed for damping of tower vibrations of fixed offshore wind turbines, where the additional actuator force is controlled using feedback from the tower displacement and the relative velocity of the damper mass. An optimum tuning procedure equivalent...... to the tuning procedure of the passive tuned mass damper combined with a simple procedure for minimizing the control force is employed for determination of optimum damper parameters and feedback gain values. By time domain simulations conducted in an aeroelastic code, it is demonstrated that the ATMD can...... be used to further reduce the structural response of the wind turbine compared with the passive tuned mass damper and this without an increase in damper mass. A limiting factor of the design of the ATMD is the displacement of the damper mass, which for the ATMD, increases to compensate for the reduction...

  5. Simple Program to Investigate Hysteresis Damping Effect of Cross-Ties on Cables Vibration of Cable-Stayed Bridges

    Directory of Open Access Journals (Sweden)

    Panagis G. Papadopoulos

    2012-01-01

    Full Text Available A short computer program, fully documented, is presented, for the step-by-step dynamic analysis of isolated cables or couples of parallel cables of a cable-stayed bridge, connected to each other and possibly with the deck of the bridge, by very thin pretensioned wires (cross-ties and subjected to variation of their axial forces due to traffic or to successive pulses of a wind drag force. A simplified SDOF model, approximating the fundamental vibration mode, is adopted for every individual cable. The geometric nonlinearity of the cables is taken into account by their geometric stiffness, whereas the material nonlinearities of the cross-ties include compressive loosening, tensile yielding, and hysteresis stress-strain loops. Seven numerical experiments are performed. Based on them, it is observed that if two interconnected parallel cables have different dynamic characteristics, for example different lengths, thus different masses, weights, and geometric stiffnesses, too, or if one of them has a small additional mass, then a single pretensioned very thin wire, connecting them to each other and possibly with the deck of the bridge, proves effective in suppressing, by its hysteresis damping, the vibrations of the cables.

  6. Vortex-Induced Vibrations of a Square Cylinder with Damped Free-End Conditions

    Directory of Open Access Journals (Sweden)

    S. Manzoor

    2013-01-01

    Full Text Available The authors report the results of vortex-induced vibrations of a square cylinder in a wind tunnel. This constitutes a high mass ratio environment. The square cylinder is mounted in the wind tunnel in such a fashion that it only performs rigid body oscillations perpendicular to the flow direction with damped free-end conditions. This physical situation allows a direct evaluation for analytical models relying on simplified 2D assumptions. The results are also compared with two-dimensional fluid-structure (CFD-CSD numerical simulations. The comparison shows that despite having one-dimensional motion, the analytical model does not predict the VIV region with correctness. Results show that the numerical simulations and experimental results differ from the analytical model for the prediction of reduced velocity corresponding to peak amplitude. Also the analytical reduced velocity envelope is underpredicted compared to both numerical simulations and experimental data despite the structure being lightly damped. The findings are significant as the experimental results for freely oscillating high mass ratio body show differences from the low mass ratio especially in the transition between VIV and galloping regions. However the numerical simulations show comparatively close agreement.

  7. Holographic-Interferometric Studies On The Damped Axially Symmetric Resonant Vibrations Of A Finite Isotropic Cylinder

    Science.gov (United States)

    Rendl, J.; Rohler, R.; Sieger, C.

    1983-12-01

    To get quantitative information about principal aspects of the near-field propagation of sound in bone conduction, model experiments were performed with transparent silicon rubber as a vibrating material. Using the transparent silicon rubber instead of the bone itself made it possible to measure amplitudes and phases on interior planes of a solid medium of finite extent. To this end several holographic techniques were employed, among them speckle interferometry for analysing in-plane vibrations. A theory was developed which describes the basic features of wave propagation and shows the influence of the viscosity of the material on propagation behaviour. The application of the results on pracitcal audiometry will be discussed.

  8. Redistribution of energy flow in a material due to damping.

    Science.gov (United States)

    Li, Xin; Pierce, Donna M; Arnoldus, Henk F

    2011-02-01

    The field lines of energy flow of the radiation emitted by a linear dipole in free space are straight lines, running radially outward from the source. When the dipole is embedded in a medium, the field lines are curves when the imaginary part of the relative permittivity is finite. It is shown that due to the damping in the material all radiation is emitted in directions perpendicular to the dipole axis, whereas for a dipole in free space the radiation is emitted in all directions except along the dipole axis. It is also shown that some field lines in the near field form semiloops. Energy flowing along these semiloops is absorbed by the material and does not contribute to the radiative power in the far field.

  9. Complex modes of vibration due to small-scale damping in a guitar topplate

    Directory of Open Access Journals (Sweden)

    J. A. Torres

    2010-04-01

    Full Text Available Modal analysis is one of the preeminent methods used by scientists and engineers to study vibrating structures. The frequency responsefunctions obtained through this method, are, in general, complex-valued. There is, however, no agreed-upon interpretation given to thereal and imaginary parts of these functions, even though it is acknowledged that their relative magnitude for different frequencies is relatedto the behaviour of the corresponding modes. A simple model is deduced to describe the shape of the spectrum associated with afinite-length time-signal. There is very good agreement between results obtained using this model and numerical results obtained for,in this case, the vibration of a guitar top-plate using finite element methods. One interpretation of the relative magnitudes of the real and imaginary parts of the frequency response functions is advanced. It is found that stationary-wave behaviour is associated with the dominance of the real or imaginary part; traveling-wave behaviour, on the other hand, occurs when the real and imaginary parts are of the same order of magnitude, as long as the scale of damping is large enough and resonance peaks in the spectrum are close enough.

  10. Accelerated lifetime test of vibration isolator made of Metal Rubber material

    Science.gov (United States)

    Ao, Hongrui; Ma, Yong; Wang, Xianbiao; Chen, Jianye; Jiang, Hongyuan

    2017-01-01

    The Metal Rubber material (MR) is a kind of material with nonlinear damping characteristics for its application in the field of aerospace, petrochemical industry and so on. The study on the lifetime of MR material is impendent to its application in engineering. Based on the dynamic characteristic of MR, the accelerated lifetime experiments of vibration isolators made of MR working under random vibration load were conducted. The effects of structural parameters of MR components on the lifetime of isolators were studied and modelled with the fitting curves of degradation data. The lifetime prediction methods were proposed based on the models.

  11. Method and apparatus for vibrating a substrate during material formation

    Science.gov (United States)

    Bailey, Jeffrey A [Richland, WA; Roger, Johnson N [Richland, WA; John, Munley T [Benton City, WA; Walter, Park R [Benton City, WA

    2008-10-21

    A method and apparatus for affecting the properties of a material include vibrating the material during its formation (i.e., "surface sifting"). The method includes the steps of providing a material formation device and applying a plurality of vibrations to the material during formation, which vibrations are oscillations having dissimilar, non-harmonic frequencies and at least two different directions. The apparatus includes a plurality of vibration sources that impart vibrations to the material.

  12. Vibration Control of Fractionally-Damped Beam Subjected to a Moving Vehicle and Attached to Fractionally-Damped Multiabsorbers

    Directory of Open Access Journals (Sweden)

    Hashem S. Alkhaldi

    2013-01-01

    Full Text Available This paper presents the dynamic response of Bernoulli-Euler homogeneous isotropic fractionally-damped simply-supported beam. The beam is attached to multi single-degree-of-freedom (SDOF fractionally-damped systems, and it is subjected to a vehicle moving with a constant velocity. The damping characteristics of the beam and SDOF systems are described in terms of fractional derivatives. Three coupled second-order fractional differential equations are produced and then they are solved by combining the Laplace transform with the decomposition method. The obtained numerical results show that the dynamic response decreases as (a the number of absorbers attached to the beam increases and (b the damping-ratios of used absorbers and beam increase. However, there are some critical values of fractional derivatives which are different from unity at which the beam has less dynamic response than that obtained for the full-order derivatives model. Furthermore, the obtained results show very good agreements with special case studies that were published in the literature.

  13. Damping Property of a Cement-Based Material Containing Carbon Nanotube

    Directory of Open Access Journals (Sweden)

    Wei-Wen Li

    2015-01-01

    Full Text Available This study aimed to explore the damping property of a cement-based material with carbon nanotube (CNT. In the study, the cement composites with different contents of CNT (0 wt%, 0.033 wt%, 0.066 wt%, and 0.1 wt% were investigated. Logarithmic Decrement method and Dynamic Mechanical Analysis (DMA method were utilized to study the damping property of CNT/cement composite. The influences of CNT on pore size distribution and microstructure of composite were analyzed by Mercury Intrusion Porosimetry (MIP and Scanning Electron Microscopy (SEM, respectively. The experimental results showed that CNT/cement composite presented higher flexural strength index than that of a pure cement paste. Additional CNT could improve the vibration-reduction capacity of cement paste. Furthermore, the experiments proved that CNT could bridge adjacent hydration products and support load transfer within cement matrix, which contributed to the energy dissipation during the loading process.

  14. Numerical analysis of non-linear vibrations of a fractionally damped cylindrical shell under the conditions of combinational internal resonance

    Directory of Open Access Journals (Sweden)

    Rossikhin Yury A.

    2018-01-01

    Full Text Available Non-linear damped vibrations of a cylindrical shell embedded into a fractional derivative medium are investigated for the case of the combinational internal resonance, resulting in modal interaction, using two different numerical methods with further comparison of the results obtained. The damping properties of the surrounding medium are described by the fractional derivative Kelvin-Voigt model utilizing the Riemann-Liouville fractional derivatives. Within the first method, the generalized displacements of a coupled set of nonlinear ordinary differential equations of the second order are estimated using numerical solution of nonlinear multi-term fractional differential equations by the procedure based on the reduction of the problem to a system of fractional differential equations. According to the second method, the amplitudes and phases of nonlinear vibrations are estimated from the governing nonlinear differential equations describing amplitude-and-phase modulations for the case of the combinational internal resonance. A good agreement in results is declared.

  15. Concerning the problem of dynamic damping of the vibration combustion self-oscillations in a liquid-propellant rocket engine

    Science.gov (United States)

    Basok, B. I.; Gotsulenko, V. V.; Gotsulenko, V. N.

    2012-11-01

    The reason for the decrease in the amplitude of longitudinal vibration combustion self-oscillations in the combustion chamber of a liquid-propellant rocket engine by means of antipulse partitions has been justified. A mathematical model of the development of combustion instability in such a chamber on attachment of a Helmholtz resonator to it has been obtained. The character of the damping of vibration combustion self-oscillations excited by the action of the Crocco mechanisms and negative thermal resistance, when varying the acoustic parameters of the resonator and of the pressure head characteristics of combustion chamber is established.

  16. The Effect of a Vibration Absorber on the Damping Properties of Alpine Skis

    Directory of Open Access Journals (Sweden)

    Stefan Schwanitz

    2018-02-01

    Full Text Available Coupled bending-torsion vibrations at the shovel are a severe problem when running an alpine ski at high velocities on hard or icy slopes. Thus, a major goal for ski manufacturers is to dampen vibrations through a proper multi-material design and/or additional absorbers. The aim of this study was to examine the effectiveness of a particular vibration absorber on a commercial slalom ski through a series of laboratory tests as well as a subjective field evaluation. Therefore, two identical pairs of ski were used and the absorber was deactivated on one pair. Laboratory tests revealed reductions of 5% to 49% of bending vibrations on skis with activated absorber. Subjective evaluation by 6 subjects suggested minor differences in the mean of the evaluated criteria turnablity, edge grip, steering behavior and stability towards a better performance of the skis with activated absorber. Subjects were able to identify the absorber mode with a success rate of 61.1%.

  17. The Shock and Vibration Bulletin. Part 1. Keynote Address, Invited Papers Damping and Isolation, Fluid-Structure Interaction

    Science.gov (United States)

    1981-05-01

    gLAsTic SUPPORTS 114CLUDING DAMPING ’I FINITE ELEMENT ANALYSIS.........................................83 A. M. Sharan, T. S. Sankar and S. Stalks ...nuances of a at the Naval Weapons Center in China Lake, California. So, physical world of shock and vibration. So I asked myself while I am not a...l Fig. 4: Schematic diagram for the experimental set-up. Fig. 5a: Pictorial view of the Instrumentation for frequency analysis. = rot = :&C lo Fig. Sb

  18. Composite materials inspection. [ultrasonic vibration holographic NDT

    Science.gov (United States)

    Erf, R. K.

    1974-01-01

    Investigation of the application requirements, advantages, and limitations of nondestructive testing by a technique of ultrasonic-vibration holographic-interferometry readout used in a production control facility for the inspection of a single product such as composite compressor blades. It is shown that, for the detection and characterization of disbonds in composite material structures, this technique may represent the most inclusive test method.

  19. Nanofiber Additions for Tailorable Vibration Damping Materials Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of NASA's Quiet Aircraft Technology project is to reduce perceived aircraft noise by half in 10 years and by 75 percent in 25 years, using 1997 levels as...

  20. Development of Composite Materials with High Passive Damping Properties

    National Research Council Canada - National Science Library

    Crocker, Malcolm J

    2006-01-01

    ... structure with high damping. Composite sandwich structures have several advantages, such as their high strength-to-weight ratio, excellent thermal insulation, and good performance as water and vapor barriers...

  1. Natural vibration frequency and damping of slender structures founded on monopiles

    DEFF Research Database (Denmark)

    Zania, Varvara

    2014-01-01

    the damping. The modified SSI eigenfrequency and damping was mostly affected by the soil–pile properties, when the structural eigenfrequency was set between the first and second eigenfrequency of the soil layer. Caution is suggested when selecting one of the popular design approaches for OWTs, since...

  2. Spectral statistics in damped systems: Diffuse field decay curvature for materials characterization

    Energy Technology Data Exchange (ETDEWEB)

    Burkhardt, J. [Department of Engineering, Purdue University at Fort Wayne, 2101 Coliseum Boulevard East, Fort Wayne, Indiana 46805-1499 (United States)

    1997-10-01

    A new nondestructive technique is proposed which exploits the unique decay characteristics of diffuse fields in nonproportionally damped systems. A power-law decay model is derived and advanced as the basis for the inverse estimation of both the strength and spatial extent of the dissipative region in nonproportionally damped systems. In materials where mechanical damage results in increased internal friction, a common effect in many engineering metals, this technique is proposed as a nondestructive technique for characterizing such damage. The results of numerical experiments on nonproportionally damped acoustic systems are presented which support the proposed technique. {copyright} {ital 1997 Acoustical Society of America.}

  3. Damping Transversal Vibrations of the Offset Cylinder of the Offset Press

    Directory of Open Access Journals (Sweden)

    Eglė Šalvienė

    2012-01-01

    Full Text Available Investigation into the influence of a dynamic vibration damper on the intensity of the absolute forced transversal vibrations of the blanket cylinder of the web printing offset press was performed. The analytical and numerical examination of the dynamic model of the cylinder was done. The obtained results have disclosed that the application of the damper decreases the intensity of printing cylinder vibrations.Article in Lithuanian

  4. Equal modal damping design for a family of resonant vibration control formats

    DEFF Research Database (Denmark)

    Krenk, Steen; Høgsberg, Jan Becker

    2013-01-01

    The principle of equal modal damping is used to give a unified presentation and calibration of resonant control of structures for different control formats, based on velocity, acceleration–position or position feedback. When introducing a resonant controller the original resonant mode splits......-velocity formats, while the position and extended position feedback format give a simple stability condition in terms of the gain factors and the structure flexibility matrix. The paper concludes with a simple design procedure based on the desired effective damping of a flexible structure with equal modal control...... of the resulting modal damping ratio. While velocity feedback, and the associated acceleration–position formats, lead to near-equal resonant peak heights of the velocity in a frequency response diagram, position feedback leads to balanced acceleration peaks. It is demonstrated, how a simple additional time...

  5. Metabolites of Trichoderma species isolated from damp building materials.

    Science.gov (United States)

    McMullin, David R; Renaud, Justin B; Barasubiye, Tharcisse; Sumarah, Mark W; Miller, J David

    2017-07-01

    Buildings that have been flooded often have high concentrations of Trichoderma spores in the air while drying. Inhaled spores and spore and mycelial fragments contain large amounts of fungal glucan and natural products that contribute to the symptoms associated with indoor mould exposures. In this study, we considered both small molecules and peptaibol profiles of T. atroviride, T. koningiopsis, T. citrinoviride, and T. harzianum strains obtained from damp buildings in eastern Canada. Twenty-residue peptaibols and sorbicillin-derived metabolites (1-6) including a new structure, (R)-vertinolide (1), were characterized from T. citrinoviride. Trichoderma koningiopsis produced several koninginins (7-10), trikoningin KA V, and the 11-residue lipopeptaibols trikoningin KB I and trikoningin KB II. Trichoderma atroviride biosynthesized a mixture of 19-residue trichorzianine-like peptaibols, whereas T. harzianum produced 18-residue trichokindin-like peptaibols and the 11-residue harzianin HB I that was subsequently identified from the studied T. citrinoviride strain. Two α-pyrones, 6-pentyl-pyran-2-one (11) and an oxidized analog (12), were produced by both T. atroviride and T. harzianum. Aside from exposure to low molecular weight natural products, inhalation of Trichoderma spores and mycelial fragments may result in exposure to membrane-disrupting peptaibols. This investigation contributes to a more comprehensive understanding of the biologically active natural products produced by fungi commonly found in damp buildings.

  6. Damping of Offshore Wind Turbine Tower Vibrations by a Stroke Amplifying Brace

    DEFF Research Database (Denmark)

    Brodersen, Mark Laier; Høgsberg, Jan Becker

    2014-01-01

    The potential of installing dampers inside the tower of an offshore wind turbine is investigated through simulations. Dampers are installed at the bottom to act on the curvature of the tower, and it is shown that dampers installed in suitable braces have the potential to increase the critical...... damping ratio of the two lowest tower modes by 1 percent. By using a toggle-brace system, damper stroke is increased, while the damper force is reduced. Finally, by installing the dampers in a symmetric configuration, tuning for maximum damping is approximately independent of the orientation of the rotor......, thereby making this installation of dampers feasible....

  7. Vibration Analysis and Control of Flexible Beam by Using Smart Damping Structures

    Science.gov (United States)

    Chen, Q.; Levy, C.

    1999-01-01

    The temperature effects on frequency, loss factor and control of a flexible beam with a constrained viscoelastic layer and shape memory alloy layer (SMA) are discussed. It is shown that the temperature in the SMA (actuation) layer is very important in the determination of frequency and loss factor of such a structure. The effects of damping layer shear modulus and damping layer height as affected by the temperature are also discussed. As temperature plays such an important role, it is, therefore, imperative to evaluate temperature effects on the control of the system as well. Results with and without active control are discussed.

  8. Lateral acoustic wave resonator comprising a suspended membrane of low damping resonator material

    Science.gov (United States)

    Olsson, Roy H.; El-Kady; , Ihab F.; Ziaei-Moayyed, Maryam; Branch; , Darren W.; Su; Mehmet F.,; Reinke; Charles M.,

    2013-09-03

    A very high-Q, low insertion loss resonator can be achieved by storing many overtone cycles of a lateral acoustic wave (i.e., Lamb wave) in a lithographically defined suspended membrane comprising a low damping resonator material, such as silicon carbide. The high-Q resonator can sets up a Fabry-Perot cavity in a low-damping resonator material using high-reflectivity acoustic end mirrors, which can comprise phononic crystals. The lateral overtone acoustic wave resonator can be electrically transduced by piezoelectric couplers. The resonator Q can be increased without increasing the impedance or insertion loss by storing many cycles or wavelengths in the high-Q resonator material, with much lower damping than the piezoelectric transducer material.

  9. Vibration control in forge hammers. [by shock wave damping in foundation platform

    Science.gov (United States)

    Moise, F.; Lazarescu, C.

    1974-01-01

    Special measures are discussed for calculating, designing and executing a forge hammer foundation, so that the vibrations that occur during its working will not be transmitted to neighboring machinery, workrooms and offices. These vibrations are harmful to the workers near the forge hammer.

  10. Reactor vibration reduction based on giant magnetostrictive materials

    Directory of Open Access Journals (Sweden)

    Yan Rongge

    2017-05-01

    Full Text Available The vibration of reactors not only produces noise pollution, but also affects the safe operation of reactors. Giant magnetostrictive materials can generate huge expansion and shrinkage deformation in a magnetic field. With the principle of mutual offset between the giant magnetostrictive force produced by the giant magnetostrictive material and the original vibration force of the reactor, the vibration of the reactor can be reduced. In this paper, magnetization and magnetostriction characteristics in silicon steel and the giant magnetostrictive material are measured, respectively. According to the presented magneto-mechanical coupling model including the electromagnetic force and the magnetostrictive force, reactor vibration is calculated. By comparing the vibration of the reactor with different inserted materials in the air gaps between the reactor cores, the vibration reduction effectiveness of the giant magnetostrictive material is validated.

  11. Reactor vibration reduction based on giant magnetostrictive materials

    Science.gov (United States)

    Rongge, Yan; Weiying, Liu; Yuechao, Wu; Menghua, Duan; Xiaohong, Zhang; Lihua, Zhu; Ling, Weng; Ying, Sun

    2017-05-01

    The vibration of reactors not only produces noise pollution, but also affects the safe operation of reactors. Giant magnetostrictive materials can generate huge expansion and shrinkage deformation in a magnetic field. With the principle of mutual offset between the giant magnetostrictive force produced by the giant magnetostrictive material and the original vibration force of the reactor, the vibration of the reactor can be reduced. In this paper, magnetization and magnetostriction characteristics in silicon steel and the giant magnetostrictive material are measured, respectively. According to the presented magneto-mechanical coupling model including the electromagnetic force and the magnetostrictive force, reactor vibration is calculated. By comparing the vibration of the reactor with different inserted materials in the air gaps between the reactor cores, the vibration reduction effectiveness of the giant magnetostrictive material is validated.

  12. Accurate calibration of RL shunts for piezoelectric vibration damping of flexible structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker; Krenk, Steen

    2016-01-01

    Piezoelectric RL (resistive-inductive) shunts are passive resonant devices used for damping of dominantvibration modes of a flexible structure and their efficiency relies on precise calibration of the shuntcomponents. In the present paper improved calibration accuracy is attained by an extension...

  13. Vibration Damping Workshop Proceedings Held at Long Beach, California on 27-29 February 1984.

    Science.gov (United States)

    1984-11-11

    variety of damping devices have been suggested [10,111. Other devices for energy dissipation were used such as draping chains over tubes [12] or permitting... devopment /operating cost by 340M UU -2 p 0 i -L . ..’ - . , ,.. . ,, _,_ ... . .-; .. :: -- _. . , .:... : . -.. .*. - - -.- 2 -,-i-. . i

  14. Atomistic theory for the damping of vibrational modes in monoatomic gold chains

    DEFF Research Database (Denmark)

    Engelund, Mads; Brandbyge, Mads; Jauho, Antti-Pekka

    2009-01-01

    for the experimentally realized case of gold chains in two different crystallographic directions. The range of the computed damping rates confirms the estimates obtained by fits to experimental data [T. Frederiksen et al., Phys. Rev. B 75, 205413 (2007)]. Our method indicates that an order-of-magnitude variation...

  15. Experimental Equipment for Damping Capacity Analyze of High or Low Internal Friction Metallic Materials

    Science.gov (United States)

    Gârnet, I. A.; Stanciu, S.; Hopulele, I.; Zaharia, M. G.; Cimpoesu, N.; Chicet, D. L.; Crăciun, R. C.

    2017-06-01

    An experimental equipment, type torsion pendulum was made in laboratory in order to analyze the damping capacity of metallic materials. The scheme of the equipment is presented, 2D and 3D visions at real scale. The equipment functioning (mechanical and electrical part) and principles are presented. In this article we present some preliminary experimental results obtained on different materials (aluminium, steel etc.) using two different methods for registration the outputs (one based on optoelectronic device with Arduino acquisition board and second on video analyze (cinematic review: video to jpeg) of the damped motion of the lead pendulum). Steel materials were with shoot penning surface modification with and without heat treatment in order to establish the heat treatment influence on the damping capacity property.

  16. Development of magnetorheological elastomers based on Deproteinised natural rubber as smart damping materials

    Science.gov (United States)

    Ismail, Nik Intan Nik; Kamaruddin, Shamsul

    2017-12-01

    Magnetorheological elastomers (MREs) are composite materials consist of micron-sized magnetizable particles carbonyl iron particles [CIPs]) embedded in a soft elastomer matrix. MRE technology offers variable stiffness and damping properties under the influence of a magnetic field. Herein, the feasibility of incorporating a new generation specialty rubber, Pureprena as a matrix for MREs was investigated. Pureprena or Deproteinised Natural Rubber (DPNR) is a specialty natural rubber that has good dynamic properties, particularly with respect to damping parameters. DPNR was compounded with 60 wt% of CIPs to fabricate MREs. The performance of the DPNR-based MRE was measured in terms of tensile strength, dynamic properties, and magnetorheological (MR) effect and compared with polyisoprene (IR)-based MRE with the same amount of CIPs. Dynamic Mechanical Analyzer (DMA) showed that the loss factor in the glass transition region of the DPNR-based MRE was higher than that of the IR-based MRE, indicating better damping properties. Further investigation was undertaken using a servo-hydraulic testing machine to characterise the effect of strain amplitude and frequency on the dynamic properties (e.g. damping coefficient) of MREs at zero magnetic fields. The results demonstrate that DPNR-based MREs possess a comparable damping coefficient to that of IR-based MREs. In addition, MR effect, which relates to the ratio between elastic modulus with applied magnetic field (on-state) to the same modulus without applied fields (off-state), was measured using a parallel plate rheometer. As a result, DPNR-based MREs have improved MR effect than that of IR-based MREs. Moreover, variable stiffness is obtained when the magnetic field was increased to 0.8T. Loss factor or tan δ of MREs was found to vary against different magnetic fields. Finally, MREs with varied stiffness and damping were found to have potential as active control devices for smart damping materials.

  17. Effect of T6 heat treatment on damping characteristics of Al/RHA ...

    Indian Academy of Sciences (India)

    torsional vibration condition. Since then much investiga- tion have been made and various damping mechanisms were discovered in metallic materials. Rohatgi et al (1994) investigated the damping capacity of graphite and silicon carbide particulate reinforced Al alloy composites. The damping capacity of graphite/Al alloy ...

  18. Active Vibration Reduction of Titanium Alloy Fan Blades (FAN1) Using Piezoelectric Materials

    Science.gov (United States)

    Choi, Benjamin; Kauffman, Jeffrey; Duffy, Kirsten; Provenza, Andrew; Morrison, Carlos

    2010-01-01

    The NASA Glenn Research Center is developing smart adaptive structures to improve fan blade damping at resonances using piezoelectric (PE) transducers. In this paper, a digital resonant control technique emulating passive shunt circuits is used to demonstrate vibration reduction of FAN1 Ti real fan blade at the several target modes. Single-mode control and multi-mode control using one piezoelectric material are demonstrated. Also a conceptual study of how to implement this digital control system into the rotating fan blade is discussed.

  19. ICAN/DAMP-integrated composite analyzer with damping analysis capabilities: User's manual

    Science.gov (United States)

    Saravanos, Dimitrious A.; Sanfeliz, Jose G.

    1992-01-01

    This manual describes the use of the computer code ICAN/DAMP (Integrated Composite Analyzer with Damping Analysis Capabilities) for the prediction of damping in polymer-matrix composites. The code is written in FORTRAN 77 and is a version of the ICAN (Integrated Composite ANalyzer) computer program. The code incorporates a new module for synthesizing the material damping from micromechanics to laminate level. Explicit micromechanics equations based on hysteretic damping are programmed relating the on-axis damping capacities to the fiber and matrix properties and fiber volume ratio. The damping capacities of unidirectional composites subjected to off-axis loading are synthesized from on-axis damping values. The hygrothermal effect on the damping performance of unidirectional composites caused by temperature and moisture variation is modeled along with the damping contributions from interfacial friction between broken fibers and matrix. The temperature rise is continuously vibrating composite plies and composite laminates is also estimated. The ICAN/DAMP user's manual provides descriptions of the damping analysis module's functions, structure, input requirements, output interpretation, and execution requirements. It only addresses the changes required to conduct the damping analysis and is used in conjunction with the 'Second Generation Integrated Composite Analyzer (ICAN) Computer Code' user's manual (NASA TP-3290).

  20. Damping of edgewise vibration in wind turbine blades by means of circular liquid dampers

    DEFF Research Database (Denmark)

    Basu, Biswajit; Zhang, Zili; Nielsen, Søren R.K.

    2016-01-01

    This paper proposes a new type of passive vibration control damper for controlling edgewise vibrations of wind turbine blades. The damper is a variant of the liquid column damper and is termed as a circular liquid column damper (CLCD). Rotating wind turbine blades generally experience a large...... centrifugal acceleration. This centrifugal acceleration makes the use of this kind of oscillatory liquid damper feasible with a small mass ratio to effectively suppress edgewise vibrations. A reduced 2-DOF non-linear model is used for tuning the CLCD attached to a rotating wind turbine blade, ignoring...... the coupling between the blade and the tower. The performance of the damper is evaluated under various rotational speeds of the rotor. A special case in which the rotational speed is so small that the gravity dominates the motion of the liquid is also investigated. Further, the legitimacy of the decoupled...

  1. Defining and comparing vibration attributes of AlSi10 foam and CFRP coated AlSi10 foam materials

    Science.gov (United States)

    Çolak, O.; Yünlü, L.

    2017-06-01

    Now, Aluminum materials have begun being manufactured as porous structures and being used with additive composite materials through emerging manufacturing technologies. These materials those porous structures have also begun being used in many areas such as automotive and aerospace due to light-weighted structures. In addition to examining mechanical behavior of porous metallic structures, examining vibration behavior is important for defining characteristic specifications. In this study, vibration attributes belong to %80 porous AlSi10 foam and CFRP coated %80 porous AlSi10 foam are determined with modal analysis. Modal parameters such as natural frequencies and damping coefficient from frequency response functions at the end of hammer impact tests. It is found that natural frequency of CFRP coated AlSi10 foam’s is 1,14 times bigger than AlSi10 foam and damping coefficient of CFRP coated AlSi10 foam is 5 times bigger than AlSi10 foam’s with tests. Dynamic response of materials in various conditions is simulated by evaluating modal parameters with FEM. According to results of the study, CFRP coating on AlSi10 foam effect vibration damping and resonance avoidance ability positively.

  2. Determination of the transient vibrations of a rigid rotor attenuated by a semiactive magnetorheological damping device by means of computational modelling

    Directory of Open Access Journals (Sweden)

    Zapoměl J.

    2013-12-01

    Full Text Available Unbalance is the principal source of increase of time varying forces transmitted between the rotor and its stationary part. Their magnitudes can be considerably reduced if the rotor is flexibly suspended and if the damping devices are added to the support elements. Their damping effect must be high for low rotor velocities and small for velocities approximately higher than the critical one to minimize the transmitted forces and the vibrations amplitude. This implies to achieve maximum efficiency of the damping elements, their damping effect has to be adaptable to the current operating conditions. Such technological solution is offered by application of a squeeze film magnetorheological damper. Its hybrid variant consisting of two damping units (one controllable in a serial arrangement is investigated in this paper. The damping takes place in two concentric lubricating films formed by normal and magnetorheological oils. The damper is equipped with an electric coil generating magnetic flux passing through the layer of the magnetorheological fluid. As resistance against its flow depends on magnetic induction, changing magnitude of the applied current enables to control the damping force. In the computational model, the rotor is considered to be absolutely rigid, unbalanced and the damping elements are represented by force couplings. The goal of the analysis is to study influence of the investigated magnetorheological damper on behaviour of a rigid rotor during different transient regimes. A special attention is focused on passing the rotor through the critical speed and on planning the dependence of the applied current on speed of the rotor rotation to achieve the optimum compromise between minimizing the transmitted forces and maximum attenuation of the rotor vibrations.

  3. Center Impedance Method for Damping Measurement

    Directory of Open Access Journals (Sweden)

    D. Malogi

    2009-01-01

    Full Text Available Damping materials are used extensively for reduction of vibration and noise. These damping materials have viscoelastic characteristics and are used by automotive and other industries. Testing of these materials is important in order to predict their performance and traditionally the damping properties are measured by the Oberst method. This paper discusses an alternate method called the Center Impedance method where force and response are measured directly and the damping properties are obtained. The Center Impedance method is easy to use requiring only standard vibration equipment for excitation, namely, shaker, and is easy to control the experiment for repeatability. Results of beams tested by both Oberst and Center Impedance methods are presented in order to validate this test method.

  4. Improved Object Detection Using a Robotic Sensing Antenna with Vibration Damping Control.

    Science.gov (United States)

    Feliu-Batlle, Vicente; Feliu-Talegon, Daniel; Castillo-Berrio, Claudia Fernanda

    2017-04-13

    Some insects or mammals use antennae or whiskers to detect by the sense of touch obstacles or recognize objects in environments in which other senses like vision cannot work. Artificial flexible antennae can be used in robotics to mimic this sense of touch in these recognition tasks. We have designed and built a two-degree of freedom (2DOF) flexible antenna sensor device to perform robot navigation tasks. This device is composed of a flexible beam, two servomotors that drive the beam and a load cell sensor that detects the contact of the beam with an object. It is found that the efficiency of such a device strongly depends on the speed and accuracy achieved by the antenna positioning system. These issues are severely impaired by the vibrations that appear in the antenna during its movement. However, these antennae are usually moved without taking care of these undesired vibrations. This article proposes a new closed-loop control schema that cancels vibrations and improves the free movements of the antenna. Moreover, algorithms to estimate the 3D beam position and the instant and point of contact with an object are proposed. Experiments are reported that illustrate the efficiency of these proposed algorithms and the improvements achieved in object detection tasks using a control system that cancels beam vibrations.

  5. Investigations of thickness-shear mode elastic constant and damping of shunted piezoelectric materials with a coupling resonator

    Science.gov (United States)

    Hu, Ji-Ying; Li, Zhao-Hui; Sun, Yang; Li, Qi-Hu

    2016-12-01

    Shear-mode piezoelectric materials have been widely used to shunt the damping of vibrations where utilizing surface or interface shear stresses. The thick-shear mode (TSM) elastic constant and the mechanical loss factor can change correspondingly when piezoelectric materials are shunted to different electrical circuits. This phenomenon makes it possible to control the performance of a shear-mode piezoelectric damping system through designing the shunt circuit. However, due to the difficulties in directly measuring the TSM elastic constant and the mechanical loss factor of piezoelectric materials, the relationships between those parameters and the shunt circuits have rarely been investigated. In this paper, a coupling TSM electro-mechanical resonant system is proposed to indirectly measure the variations of the TSM elastic constant and the mechanical loss factor of piezoelectric materials. The main idea is to transform the variations of the TSM elastic constant and the mechanical loss factor into the changes of the easily observed resonant frequency and electrical quality factor of the coupling electro-mechanical resonator. Based on this model, the formular relationships are set up theoretically with Mason equivalent circuit method and they are validated with finite element (FE) analyses. Finally, a prototype of the coupling electro-mechanical resonator is fabricated with two shear-mode PZT5A plates to investigate the TSM elastic constants and the mechanical loss factors of different circuit-shunted cases of the piezoelectric plate. Both the resonant frequency shifts and the bandwidth changes observed in experiments are in good consistence with the theoretical and FE analyses under the same shunt conditions. The proposed coupling resonator and the obtained relationships are validated with but not limited to PZT5A. Project supported by the National Defense Foundation of China (Grant No. 9149A12050414JW02180).

  6. Experimental Characterization of Damped CFRP Materials with an Application to a Lightweight Car Door

    Directory of Open Access Journals (Sweden)

    Alessandro Fasana

    2017-01-01

    Full Text Available This paper presents a complete design procedure for defining a dynamic model of a Carbon Fibre Reinforced Polymer (CFRP component with an embedded damping material layer. The experiment to determine the mechanical characteristics of the materials is performed by the Oberst beam technique to provide precise material properties for a Finite Element (FE model. The technique implemented, namely, the Linear Identification by Polynomial Expansion in the Z-domain (LIPEZ method, is used to compare the experimental data with the numerical simulation results provided by the modal parameters to be compared with the numerical results. Two automotive components (a leaf spring and an outer shell of front door have been tested. The research revealed the utter importance of a correct definition of the geometry for the numerical models. Finally, the positive effects for acoustic performance with a thin layer of KRAIBON® SUT9609/24 damping material, included in the stacking sequence of the CFRP component, are highlighted.

  7. Characterization and preparation of p(U-MMA-An) interpenetrating polymer network damping and absorbing material.

    Science.gov (United States)

    Liu, Jun; Li, Qingshan; Zhuo, Yuguo; Hong, Wei; Lv, Wenfeng; Xing, Guangzhong

    2014-06-01

    P(U-MMA-ANI) interpenetrating polymer network (IPN) damping and absorbing material is successfully synthesized by PANI particles served as an absorbing agent with the microemulsion polymerization and P(U-MMA) foam IPN network structure for substrate materials with foaming way. P(U-MMA-ANI) IPN is characterized by the compression mechanical performance testing, TG-DSC, and DSC. The results verify that the P(U-MMA) IPN foam damping material has a good compressive strength and compaction cycle property, and the optimum content of PMMA was 40% (mass) with which the SEM graphs do not present the phase separation on the macro level between PMMA and PU, while the phase separation was observed on the micro level. The DTG curve indicates that because of the formation of P(U-MMA) IPN, the decomposition temperature of PMMA and the carbamate in PU increases, while that of the polyol segment in PU has almost no change. P(U-MMA-ANI) IPN foam damping and absorbing material is obtained by PANI particles served as absorbing agent in the form of filler, and PMMA in the form of micro area in substrate material. When the content of PANI was up to 2.0% (mass), the dissipation factor of composites increased, and with the increasing of frequency the dissipation factor increased in a straight line.

  8. Understanding how the placement of an asymmetric vibration damping tool within drilling while underreaming can influence performance and reliability

    Energy Technology Data Exchange (ETDEWEB)

    Kabbara, Alan; McCarthy, John; Burnett, Timm; Forster, Ian [National Oilwell Varco Downhole Ltd. (NOV), Houston, TX (United States)

    2012-07-01

    This paper describes the work, on test rigs and full-scale drilling rigs, carried out with respect to placement of an Asymmetric Vibration Damping Tool (AVDT) within drilling while under reaming operations. An AVDT, by virtue of the forward synchronous motion imposed on the drill string, offers benefits in minimizing down hole vibration-related tool failures and therefore maximizing rate of penetration (ROP). Of interest in using the AVDT is the tendency to minimize stick slip by means of the parasitic torque it generates. This is of particular importance during under reaming operations. While under reaming, stick slip can result in low (ROP) and potentially an increased incidence of down hole tool failures. The use of an AVDT in these operations has been shown to significantly reduce stick slip. However, due to the forward synchronous motion caused by the AVDT, there is the potential to cause eccentric wear to the Bottom Hole Assembly (BHA) components in the vicinity of the AVDT. If allowed to progress, this eccentric wear can cause a reduction in down hole tool life and drilling performance. Eliminating eccentric wear would be beneficial in reducing repair costs, extending component life and further improving drilling performance. To minimize eccentric wear and maximize drilling performance, the placement of the AVDT within the BHA is critical. This paper describes how the placement of intermediate stabilizers between the AVDT and the under reamer can minimize eccentric wear to the under reamer and the adjacent drill string due to the forward synchronous whirl induced by the AVDT. This approach allows the full benefits of the AVDT to be recognized while reducing the potentially damaging effects of eccentric wear to other BHA components. The work has drawn upon small-scale rig testing, full-scale testing at the Ullrigg test facility in Norway and from real-world drilling and under reaming operations in the USA. (author)

  9. Optimal Damping of Stays in Cable-Stayed Bridges for In-Plane Vibrations

    DEFF Research Database (Denmark)

    Jensen, C.N.; Nielsen, S.R.K.; Sørensen, John Dalsgaard

    2002-01-01

    cable-stayed bridges are often designed as twin cables with a spacing of, say 1m. In such cases, it is suggested in the paper to suppress the mentioned in-plane types of vibrations by means of a tuned mass–damper (TMD) placed between the twin cables at their midpoints. The TMD divides the stay into four...... of the mentioned frequencies. The spring and the damper constants of the TMD are optimized so that the variances of the displacement of the adjacent four half-cables, the support point of the TMD and the secondary mass are minimized. At optimal design, it is shown that the variances reduce below 14% of those...

  10. Frequency and damping ratio assessment of high-rise buildings using an Automatic Model-Based Approach applied to real-world ambient vibration recordings

    Science.gov (United States)

    Nasser, Fatima; Li, Zhongyang; Gueguen, Philippe; Martin, Nadine

    2016-06-01

    This paper deals with the application of the Automatic Model-Based Approach (AMBA) over actual buildings subjected to real-world ambient vibrations. In a previous paper, AMBA was developed with the aim of automating the estimation process of the modal parameters and minimizing the estimation error, especially that of the damping ratio. It is applicable over a single-channel record, has no parameters to be set, and no manual initialization phase. The results presented in this paper should be regarded as further documentation of the approach over real-world ambient vibration signals.

  11. A METHOD OF DETERMINING THE COORDINATES OF THE STIFFNESS CENTER AND THE STIFFNESS PRINCIPAL AXIS OF THE VIBRATING SYSTEM WITH DAMPING

    Directory of Open Access Journals (Sweden)

    Dang Xuan Truong

    2014-12-01

    Full Text Available The report presents a methodology to determine the directions of the stiffness principal axis (in this case subject to the linear displacement and forced rotation angle of a solid object interact with the surrounding environment by resilient bearing supports. The results also show that determining the coordinates of the stiffness center in the vibrating system with damping factors is necessary in our research.

  12. Simultaneous Composite Tailoring and Bending Control Optimization for Damping the Torsional Vibration of a Plate.

    Science.gov (United States)

    1996-06-01

    to the specifications stated in the relevant standards for shear and tension testing , ASTM D3039 -76 and D3518-76. Prior to testing , electric...graphite, carbon , boron, and metal fibers ; and matrix materials such as epoxy, metal, and carbon versus the previously mentioned materials and glass...material follow the guidelines provided by ASTM . The standards followed for determining the tensile and shear properties are ASTM D3039 -76 and ASTM D3518

  13. Damping of vibrational excitations in glasses at terahertz frequency: The case of 3-methylpentane

    KAUST Repository

    Baldi, Giacomo

    2017-10-24

    We report a compared analysis of inelastic X ray scattering (IXS) and of low frequency Raman data of glassy 3-methylpentane. The IXS spectra have been analysed allowing for the existence of two distinct excitations at each scattering wavevector obtaining a consistent interpretation of the spectra. In particular, this procedure allows us to interpret the linewidth of the modes in terms of a simple model which relates them to the width of the first sharp diffraction peak in the static structure factor. In this model, the width of the modes arises from the blurring of the dispersion curves which increases approaching the boundary of the first pseudo-Brillouin zone. The position of the boson peak contribution to the density of vibrational states derived from the Raman scattering measurements is in agreement with the interpretation of the two excitations in terms of a longitudinal mode and a transverse mode, the latter being a result of the mixed character of the transverse modes away from the center of the pseudo-Brillouin zone.

  14. Structural analysis of composite wind turbine blades nonlinear mechanics and finite element models with material damping

    CERN Document Server

    Chortis, Dimitris I

    2013-01-01

    This book concerns the development of novel finite elements for the structural analysis of composite beams and blades. The introduction of material damping is also an important aspect of composite structures and it is presented here in terms of their static and dynamic behavior. The book thoroughly presents a new shear beam finite element, which entails new blade section mechanics, capable of predicting structural blade coupling due to composite coupling and/or internal section geometry. Theoretical background is further expanded towards the inclusion of nonlinear structural blade models and damping mechanics for composite structures. The models effectively include geometrically nonlinear terms due to large displacements and rotations, improve the modeling accuracy of very large flexible blades, and enable the modeling of rotational stiffening and buckling, as well as, nonlinear structural coupling. Validation simulations on specimen level study the geometric nonlinearities effect on the modal frequencies and...

  15. Porosity-dependent nonlinear forced vibration analysis of functionally graded piezoelectric smart material plates

    Science.gov (United States)

    Qing Wang, Yan; Zu, Jean W.

    2017-10-01

    This work investigates the porosity-dependent nonlinear forced vibrations of functionally graded piezoelectric material (FGPM) plates by using both analytical and numerical methods. The FGPM plates contain porosities owing to the technical issues during the preparation of FGPMs. Two types of porosity distribution, namely, even and uneven distribution, are considered. A modified power law model is adopted to describe the material properties of the porous FGPM plates. Using D’Alembert’s principle, the out-of-plane equation of motion is derived by taking into account the Kármán nonlinear geometrical relations. After that, the Galerkin method is used to discretize the equation of motion, resulting in a set of ordinary differential equations with respect to time. These ordinary differential equations are solved analytically by employing the harmonic balance method. The approximate analytical results are verified by using the adaptive step-size fourth-order Runge-Kutta method. By means of the perturbation technique, the stability of approximate analytical solutions is examined. An interesting nonlinear broadband vibration phenomenon is detected in the FGPM plates with porosities. Nonlinear frequency-response characteristics of the present smart structures are investigated for various system parameters including the porosity type, the porosity volume fraction, the electric potential, the external excitation, the damping and the constituent volume fraction. It is found that these parameters have significant effects on the nonlinear vibration characteristics of porous FGPM plates.

  16. Further developments in material properties determined by vibration analysis

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang; Andreasen, Lotte; Seifert, Mette

    1997-01-01

    A method was described in Materialnyt 1 (1995) on "Material properties determined by vibration analysis". This new method of materials testing has been further developed as the result of research at the Building Materials Laboratory, Technical University of Denmark.Practical aspects of the method...... have been studied by testing a number of building materials. The method has been PC-integrated with the Brüel & Kjær's type 3550 vibration equipment - and special user menus have been developed to facilitate handling of the method in practice. Limits on range of test frequencies applied are discussed...... with respect to configurations of vibration equipment and shapes of test specimens used. Sensitivity studies have been made to identify sources of errors which may disturb the reliability of the method used in practice. Practical aspects with respect to test set-ups are considered in these studies - as well...

  17. The Shock and Vibration Bulletin. Part 4. Prediction and Experimental Techniques, Isolation and Damping

    Science.gov (United States)

    1973-06-01

    t-c 2<J0< :. only fo-.n materials were se’t-cted for this peper because they are typical of what is available for four important temperature...tensil strength which still wasn’t good enough until we added quite a bit of carbon black filler. This increased the tensil strength enough so it

  18. Design, Fabrication, and Properties of High Damping Metal Matrix Composites—A Review

    Directory of Open Access Journals (Sweden)

    Qianfeng Fang

    2009-08-01

    Full Text Available Nowadays it is commonly considered that high damping materials which have both the good mechanical properties as structural materials and the high damping capacity for vibration damping are the most direct vibration damping solution. In metals and alloys however, exhibiting simultaneously high damping capacity and good mechanical properties has been noted to be normally incompatible because the microscopic mechanisms responsible for internal friction (namely damping capacity are dependent upon the parameters that control mechanical strength. To achieve a compromise, one of the most important methods is to develop two-phase composites, in which each phase plays a specific role: damping or mechanical strength. In this review, we have summarized the development of the design concept of high damping composite materials and the investigation of their fabrication and properties, including mechanical and damping properties, and suggested a new design concept of high damping composite materials where the hard ceramic additives exhibit high damping capacity at room temperature owing to the stress-induced reorientation of high density point defects in the ceramic phases and the high damping capacity of the composite comes mainly from the ceramic phases.

  19. Spin waves damping in nanometre-scale magnetic materials (Review Article)

    Science.gov (United States)

    Krivoruchko, V. N.

    2015-09-01

    Spin dynamics in magnetic nanostructured materials is a topic of great current interest. To describe spin motions in such magnetic systems, the phenomenological Landau-Lifshitz (LL), or the LL-Gilbert (LLG), equation is widely used. Damping term is one of the dominant features of magnetization dynamics and plays an essential role in these equations of motion. The form of this term is simple; however, an important question arises whether it provides a proper description of the magnetization coupling to the thermal bath and the related magnetic fluctuations in the real nanometre-scale magnetic materials. It is now generally accepted that for nanostructured systems the damping term in the LL (LLG) equation fails to account for the systematics of the magnetization relaxation, even at the linear response level. In ultrathin films and nanostructured magnets particular relaxation mechanisms arise, extrinsic and intrinsic, which are relevant at nanometre-length scales, yet are not so efficient in bulk materials. These mechanisms of relaxation are crucial for understanding the magnetization dynamics that results in a linewidth dependence on the nanomagnet's size. We give an overview of recent efforts regarding the description of spin waves damping in nanostructured magnetic materials. Three types of systems are reviewed: ultrathin and exchange-based films, magnetic nanometre-scale samples and patterned magnetic structures. The former is an example of a rare case where consideration can be done analytically on microscopic footing. The latter two are typical samples when analytical approaches hardly have to be developed and numerical calculations are more fruitful. Progress in simulations of magnetization dynamics in nanometre-scale magnets gives hopes that a phenomenological approach can provide us with a realistic description of spin motions in expanding diverse of magnetic nanostructures.

  20. Determination of the structural damping coefficients of six full-scale helicopter rotor blades of different materials and methods of construction

    Science.gov (United States)

    Gibson, Frederick W

    1956-01-01

    Results of an experimental investigation of the structural damping of six full-scale helicopter rotor blades, made to determine the variation of structural damping with materials and methods of construction, are presented. The damping of the blades was determined for the first three flapwise bending modes, first chordwise bending mode, and first torsion mode. The contribution of structural damping to the total damping of the blades is discussed for several aerodynamic conditions in order to point out situations where structural damping is significant.

  1. Non-linear three-dimensional large-amplitude damped free vibration of a stiff elastic stretched string

    Science.gov (United States)

    Watzky, A.

    1992-02-01

    In the numerous works trying to describe the free vibration of stretched elastic strings, phenomena due to non-linear geometrical modifications in a three-dimensional large amplitude motion are separated from those due to the string's stiffness, in which case torsional vibrations cannot be taken into account. In order to fill this gap with a more complete model and to specify its field of validity the problem set up again, starting from three-dimensional elasticity for finite displacements with small strains of a slender homogeneous elastic cylindrical rod under initial stress. The original geometrical construction which gives the cross-section's orientation during the motion is detailed. With the symmetry of the problem preserved, it provides a description of simple physical meaning and in particular the torsion is used as a parameter. The goal of this study being the determination of the deformed shape of the central line, the three spatial variables are reduced to one through expressions for the resultant forces and moments on the cross-sections, leading to macroscopic equations of motion which are simplified in the case of uncoupled transverse and longitudinal modes. For the first time, the equations of motion introduce a coupling torsion term and include existing string and beam models, which can thus be considered as particular cases. The assumptions and generalizations are discussed and the influences of the different terms are described. While this work is based on the limits imposed by material linearity, it provides a useful basic tool for the study of the transverse vibrations of slender elastic beams, including the commonly avoided torsional phenomena.

  2. [Influence of several excipients on damp-proof performance of pharmaceutical materials of traditional Chinese medicine].

    Science.gov (United States)

    Yin, Xiao-Qin; Xu, Jia-Yin; Du, Lin-Jiao; Chen, Yan-Jun

    2013-07-01

    To study the influence of several excipients on damp-proof performance of pharmaceutical materials of traditional Chinese medicine. The moisture absorption rate and parameters of hydroscopicity were used as the evaluation index of the damp-proof property of the complex Chinese medicine and preparation 1 and 2. The moisture rate of complex Chinese medicine 1 was 62.54%, the critical relative humidity (CRH) was 38%. The moisture rate of complex Chinese medicine 2 was 16.36%, the CRH was 53%. Excipients had different effect on lower the hyproscopic property of complex Chinese medicine 1 and 2. The initial moisture adsorption velocity of excipients of complex Chinese medicine 1 in a ascending order were dextrin lactose excipients in a ascending order were dextrin = calcium hydrogen phosphate = micro crystalline cellulose lactose excipients in a ascending order were dextrin lactose excipients of complex Chinese medicine 2 in a ascending order were mannitol lactose excipients in a ascending order were mannitol = dextrin = calcium hydrogen phosphate lactose excipients in a ascending order were mannitol lactose excipients of preparation based on the property of the complex traditional Chinese medicine. The study provided experimental evidences for the research and development of the pharmaceutical materials of traditional Chinese medicine.

  3. Fabrication of Biocompatible, Vibrational Magnetoelastic Materials for Controlling Cellular Adhesion

    Directory of Open Access Journals (Sweden)

    Rupak M. Rajachar

    2012-02-01

    Full Text Available This paper describes the functionalization of magnetoelastic (ME materials with Parylene-C coating to improve the surface reactivity to cellular response. Previous study has demonstrated that vibrating ME materials were capable of modulating cellular adhesion when activated by an externally applied AC magnetic field. However, since ME materials are not inherently biocompatible, surface modifications are needed for their implementation in biological settings. Here, the long-term stability of the ME material in an aqueous and biological environment is achieved by chemical-vapor deposition of a conformal Parylene-C layer, and further functionalized by methods of oxygen plasma etching and protein adsorption. In vitro cytotoxicity measurement and characterization of the vibrational behavior of the ME materials showed that Parylene-C coatings of 10 µm or greater could prevent hydrolytic degradation without sacrificing the vibrational behavior of the ME material. This work allows for long-term durability and functionality of ME materials in an aqueous and biological environment and makes the potential use of this technology in monitoring and modulating cellular behavior at the surface of implantable devices feasible.

  4. Dynamic profile of a prototype pivoted proof-mass actuator. [damping the vibration of large space structures

    Science.gov (United States)

    Miller, D. W.

    1981-01-01

    A prototype of a linear inertial reaction actuation (damper) device employing a flexure-pivoted reaction (proof) mass is discussed. The mass is driven by an electromechanic motor using a dc electromagnetic field and an ac electromagnetic drive. During the damping process, the actuator dissipates structural kinetic energy as heat through electromagnetic damping. A model of the inertial, stiffness and damping properties is presented along with the characteristic differential equations describing the coupled response of the actuator and structure. The equations, employing the dynamic coefficients, are oriented in the form of a feedback control network in which distributed sensors are used to dictate actuator response leading to a specified amount of structural excitation or damping.

  5. A study on the damping capacity of BaTiO3-reinforced Al-matrix ...

    Indian Academy of Sciences (India)

    strength and high damping capacity. Ferroelectric and piezoelectric ceramics can exhibit con- siderable high vibration damping capacity due to the anelas- tic response of ferroelastic domains to an external applied stress. Some piezoelectric materials such as BaTiO3 PZT. (Pb(ZrTi)O3) and LiNbO3 have been focussed and ...

  6. Material removal mechanisms in abrasive vibration polishing of complex molds

    Science.gov (United States)

    Brinksmeier, E.; Riemer, O.; Schulte, H.

    2010-10-01

    Optical and medical industries are demanding a large variety of optical elements exhibiting complex geometries and multitude opto-functional areas in the range of a few millimeters [1]. Therefore, mold inserts made of steel or carbides must be finished by polishing for the replication of glass and plastic lenses [2]. For polishing theses complex components in the shape of localized cavities or grooves the application of rotating polishing pads is very limited. Established polishing processes are not applicable, so state of the art is a time consuming and therefore expensive polishing procedures by hand. An automated process with conventional polishing machines is impossible because of the complex mold insert geometry. The authors will present the development of a new abrasive polishing process for finishing these complex mold geometries to optical quality. The necessary relative velocity in the contact area between polishing pad and workpiece surface is exclusively realized by vibration motions which is an advantage over vibration assisted rotating polishing processes. The absence of rotation of the pad opens up the possibility to machine new types of surface geometries. The specific influence factors of vibration polishing were analyzed and will be presented. The determination of material removal behavior and polishing effect on planar steel samples has shown that the conventional abrasive polishing hypothesis of Preston is applicable to the novel vibration polishing process. No overlaid chemical material removal appears.

  7. Structural dynamic modification using additive damping

    Indian Academy of Sciences (India)

    Some current trends for vibration control are also discussed. Keywords. Structural modifications; viscoelastic damping; perturbation; sensitivity analysis; optimization; vibration control. 1. Introduction. Vibrations in machines and structures, if not properly controlled, may cause component fatigue and human discomfort.

  8. Inspection for kissing bonds in composite materials using vibration measurements

    Science.gov (United States)

    Adams, Douglas E.; Sharp, Nathan D.; Myrent, Noah; Sterkenburg, Ronald

    2011-04-01

    Improper bonding of composite structures can result in close contact cracks under compressive stresses, called kissing bonds. These bond defects are very difficult to detect using conventional inspection techniques such as tap testing or local ultrasonic scanning and can lead to local propagation of damage if the structure is subjected to crack opening stresses. A method is investigated for identifying kissing bonds in composite material repairs based on vibration measurements. A damage feature of the kissing bond is extracted from the response of the input-output measurement that is a function of the structural path. This path exhibits local decoupling associated with the close contact cracks. Experimental vibration measurements from sandwich composite materials are presented along with the results of the damage detection algorithm for the healthy sections of the material and the kissing bond sections. A vibration based inspection technique could increase the ability to detect kissing bonds in composite material repairs while decreasing inspection time. Benefits of this method of identification over conventional techniques include its robust, objective damage detection methodology and the reduced requirement for specimen preparation and surface texture when compared to ultrasonic scanning.

  9. Vibrational coherence in polar solutions of Zn(II) tetrakis(N-methylpyridyl)porphyrin with Soret-band excitation: rapidly damped intermolecular modes with clustered solvent molecules and slowly damped intramolecular modes from the porphyrin macrocycle.

    Science.gov (United States)

    Dillman, Kevin L; Shelly, Katherine R; Beck, Warren F

    2009-04-30

    Ground-state coherent wavepacket motions arising from intermolecular modes with clustered, first-shell solvent molecules were observed using the femtosecond dynamic absorption technique in polar solutions of Zn(II) meso-tetrakis(N-methylpyridyl)porphyrin (ZnTMPyP) with excitation in the Soret absorption band. As was observed previously in bacteriochlorophyll a solution, the pump-probe transients in ZnTMPyP solutions are weakly modulated by slowly damped (effective damping time gamma > 1 ps) features that are assigned to intramolecular modes, the skeletal normal modes of vibration of the porphyrin. The 40 cm(-1) and 215 cm(-1) modes from the metal-doming and metal-solvent-ligand modes, respectively, are members of this set of modulation components. A slowly damped 2-4 cm(-1) component is assigned to the internal rotation of the N-methylpyridyl rings with respect to the porphyrin macrocycle; this mode obtains strong resonance Raman intensity enhancement from an extensive delocalization of pi-electron density from the porphyrin in the ground state onto the rings in the pi* excited states. The dominant features observed in the pump-probe transients are a pair of rapidly damped (gamma modes with solvent molecules. This structural assignment is supported by an isotope-dependent shift of the average mode frequencies in methanol and perdeuterated methanol. The solvent dependence of the mean intermolecular mode frequency is consistent with a van der Waals intermolecular potential that has significant contributions only from the London dispersion and induction interactions; ion-dipole or ion-induced-dipole terms do not make large contributions because the pi-electron density is not extensively delocalized onto the N-methylpyridyl rings. The modulation depth associated with the intermolecular modes exhibits a marked dependence on the electronic structure of the solvent that is probably related to the degree of covalency; the strongest modulations are observed in acetonitrile

  10. Viability Analysis of Waste Tires as Material for Rail Vibration and Noise Control in Modern Tram Track Systems

    Directory of Open Access Journals (Sweden)

    Caiyou Zhao

    2015-01-01

    Full Text Available This research study focused on the effect of using damping chamber elements made from waste tires on railway noise reduction. First, the energy absorption characteristics of damping chamber elements with various gradation combinations and compaction indices were measured in the laboratory using compression testing. The laboratory compression results demonstrated that the optimal gradation combination of damping chamber elements is as follows: the content of fine rubber particles is 10%, the content of coarse granules is 90%, and the optimal compaction index is 0.98. Next, the findings from the laboratory compression-test studies were used to produce damping chamber elements that were applied to a full-scale modern track model in the laboratory. The measurements of the dynamic properties indicated that the damping chamber elements could significantly reduce the vibration levels of the rail head. Finally, the damping chamber elements, which had been proven effective through laboratory dynamic tests, were widely applied to test rail sections in the field. The field tests demonstrated that damping chamber elements can significantly increase the track vibration decay rate in the frequency range of 200–10000 Hz. Therefore, damping chamber elements made from waste tires are able to control rail vibration and noise in modern tram track systems.

  11. Fatigue failure of materials under narrow band random vibrations. I.

    Science.gov (United States)

    Huang, T. C.; Hubbard, R. B.; Lanz, R. W.

    1971-01-01

    A novel approach for the study of fatigue failure of materials under the multifactor influence of narrow band random vibrations is developed. The approach involves the conduction of an experiment in conjunction with various statistical techniques. Three factors including two statistical properties of the excitation or response are considered and varied simultaneously. A minimum of 6 tests for 3 variables is possible for a fractional f actorial design. The four coefficients of the predicting equation can be independently estimated. A look at 3 predicting equations shows the predominant effect of the root mean square stress of the first order equation.

  12. Passively Shunted Piezoelectric Damping of Centrifugally-Loaded Plates

    Science.gov (United States)

    Duffy, Kirsten P.; Provenza, Andrew J.; Trudell, Jeffrey J.; Min, James B.

    2009-01-01

    Researchers at NASA Glenn Research Center have been investigating shunted piezoelectric circuits as potential damping treatments for turbomachinery rotor blades. This effort seeks to determine the effects of centrifugal loading on passively-shunted piezoelectric - damped plates. Passive shunt circuit parameters are optimized for the plate's third bending mode. Tests are performed both non-spinning and in the Dynamic Spin Facility to verify the analysis, and to determine the effectiveness of the damping under centrifugal loading. Results show that a resistive shunt circuit will reduce resonant vibration for this configuration. However, a tuned shunt circuit will be required to achieve the desired damping level. The analysis and testing address several issues with passive shunt circuit implementation in a rotating system, including piezoelectric material integrity under centrifugal loading, shunt circuit implementation, and tip mode damping.

  13. Harnessing the damping properties of materials for high-speed atomic force microscopy.

    Science.gov (United States)

    Adams, Jonathan D; Erickson, Blake W; Grossenbacher, Jonas; Brugger, Juergen; Nievergelt, Adrian; Fantner, Georg E

    2016-02-01

    The success of high-speed atomic force microscopy in imaging molecular motors, enzymes and microbes in liquid environments suggests that the technique could be of significant value in a variety of areas of nanotechnology. However, the majority of atomic force microscopy experiments are performed in air, and the tapping-mode detection speed of current high-speed cantilevers is an order of magnitude lower in air than in liquids. Traditional approaches to increasing the imaging rate of atomic force microscopy have involved reducing the size of the cantilever, but further reductions in size will require a fundamental change in the detection method of the microscope. Here, we show that high-speed imaging in air can instead be achieved by changing the cantilever material. We use cantilevers fabricated from polymers, which can mimic the high damping environment of liquids. With this approach, SU-8 polymer cantilevers are developed that have an imaging-in-air detection bandwidth that is 19 times faster than those of conventional cantilevers of similar size, resonance frequency and spring constant.

  14. Effect of substitutional defects on Kambersky damping in L1{sub 0} magnetic materials

    Energy Technology Data Exchange (ETDEWEB)

    Qu, T. [School of Physics and Astronomy, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Victora, R. H., E-mail: victora@umn.edu [School of Physics and Astronomy, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Department of Electrical and Computer Engineering, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2015-02-16

    Kambersky damping, representing the loss of magnetic energy from the electrons to the lattice through the spin orbit interaction, is calculated for L1{sub 0} FePt, FePd, CoPt, and CoPd alloys versus chemical degree of order. When more substitutional defects exist in the alloys, damping is predicted to increase due to the increase of the spin-flip channels allowed by the broken symmetry. It is demonstrated that this corresponds to an enhanced density of states (DOS) at the Fermi level, owing to the rounding of the DOS with loss of long-range order. Both the damping and the DOS of the Co-based alloy are found to be less affected by the disorder. Pd-based alloys are predicted to have lower damping than Pt-based alloys, making them more suitable for high density spintronic applications.

  15. Using piezo-electric material to simulate a vibration environment

    Science.gov (United States)

    Jepsen, Richard A.; Davie, Neil T.; Vangoethem, Douglas J.; Romero, Edward F.

    2010-12-14

    A target object can be vibrated using actuation that exploits the piezo-electric ("PE") property. Under combined conditions of vibration and centrifugal acceleration, a centrifugal load of the target object on PE vibration actuators can be reduced by using a counterweight that offsets the centrifugal loading. Target objects are also subjected to combinations of: spin, vibration, and acceleration; spin and vibration; and spin and acceleration.

  16. The Shock and Vibration Bulletin. Part 2. Model Test and Analysis, Testing Techniques, Machinery Dynamics, Isolation and Damping, Structural Dynamics

    Science.gov (United States)

    1986-08-01

    jBfr 5? JOR JS T SIONAL/lBRATIONjerF^EAR-RANCHED PROPULSION.gVSTEMS j... 117 / H.F. Tavares, Cepstrum Engenharia Ltda., Rio de Janeiro, Brazil and V...MODELLING IN FINITE ELEMENT ANALYSES OF TORSIONAL VIBRATION OF GEAR-BRANCHED PROPULSION SYSTEMS H. F. Tavares Cepstrum Engenharia Ltda. S8o Paulo

  17. Experimental Investigation on the Material Removal of the Ultrasonic Vibration Assisted Abrasive Water Jet Machining Ceramics

    Directory of Open Access Journals (Sweden)

    Tao Wang

    2017-01-01

    Full Text Available The ultrasonic vibration activated in the abrasive water jet nozzle is used to enhance the capability of the abrasive water jet machinery. The experiment devices of the ultrasonic vibration assisted abrasive water jet are established; they are composed of the ultrasonic vibration producing device, the abrasive supplying device, the abrasive water jet nozzle, the water jet intensifier pump, and so on. And the effect of process parameters such as the vibration amplitude, the system working pressure, the stand-off, and the abrasive diameter on the ceramics material removal is studied. The experimental result indicates that the depth and the volume removal are increased when the ultrasonic vibration is added on abrasive water jet. With the increase of vibration amplitude, the depth and the volume of material removal are also increased. The other parameters of the ultrasonic vibration assisted abrasive water jet also have an important role in the improvement of ceramic material erosion efficiency.

  18. A Semenov approach to the modelling of thermal runaway of damp combustible material

    Science.gov (United States)

    McIntosh, A. C.

    1993-01-01

    Semenov theory for the self-heating of a reactive slab is extended to take account of the presence of water vapour. In this paper, mass changes due to evaporation/condensation are neglected but heat exchange is retained in the energy equation. By doing this, a simple easily solvable set of equations can be set up to represent the thermal behaviour of the slab. No account is taken of possible wet exothermic reactions in this paper. The aim is simply to understand the effects of evaporation/condensation on the overall thermal history. Using a simple model which treats the mass changes within the material as negligible, the competitive effects of condensation and evaporation are shown to produce a two-time situation which depends crucially on the surface mass transfer/heat transfer ratio hm. Either self-heating occurs at a lower rate than that due to dry oxidation, or else a maximum temperature is reached before a lower equilibrium steady-state temperature is achieved. Thus, compared to the dry case, in general terms, evaporation certainly encourages stability. However, the final strictly subcritical steady state will not always be achieved due to the competitive process between recondensation and evaporation loss at the surface at medium timescales. A set of quasi-steady states is identified which yield plots of a more restrictive critical value of temperature against the Frank-Kamenetskii parameter (proportional to the thickness of the slab and its reactivity). If the value of hm is such that the maximum temperature reaches this critical value, then thermal runaway can still take place even though the starting value of temperature was strictly below the true (damp) final steady-state critical value.

  19. Atomistic Mechanisms for Viscoelastic Damping in Inorganic Solids

    Science.gov (United States)

    Ranganathan, Raghavan

    the microstructural length-scale of the composite. The second class of materials consist of structurally heterogeneous binary alloys that are either ordered, random or glassy. Vastly different mechanisms for viscoelastic damping arise for the three structures - random alloy and glass are observed to exhibit significant damping owing to large anharmonicity in the coupling between vibrational modes, which is a direct consequence of the chemical heterogeneity. Additionally, at low shear frequencies, glass exhibits significant long-time scale structural relaxation that results in persistent damping over a large range of frequencies. Finally, a critical analysis of various factors that affect damping in inorganic glasses is made. We show that damping in glasses exhibits a striking commonality - at high frequencies, vibrational anharmonicity leads to a peak in damping for all glasses commensurate with the range of vibrational frequencies of the glass; at intermediate and low frequencies, structural relaxation leads to persistent, nearly-constant damping. The frequency-dependent damping mechanisms and structure-property relations observed with respect to damping are expected to enable the design of novel structures with favorable damping characteristics.

  20. Numerical Modelling of Rubber Vibration Isolators: identification of material parameters

    NARCIS (Netherlands)

    Beijers, C.A.J.; Noordman, Bram; de Boer, Andries; Ivanov, N.I.; Crocker, M.J.

    2004-01-01

    Rubber vibration isolators are used for vibration isolation of engines at high frequencies. To make a good prediction regarding the characteristics of a vibration isolator in the design process, numerical models can be used. However, for a reliable prediction of the dynamic behavior of the isolator,

  1. Effects on perceived air quality and symptoms of exposure to microbially produced metabolites and compounds emitted from damp building materials.

    Science.gov (United States)

    Claeson, A-S; Nordin, S; Sunesson, A-L

    2009-04-01

    This work investigated perceived air quality and health effects from exposure to low to high levels of volatile organic compounds (VOCs) emitted from damp building materials and a mixture of molds growing on the materials. A mixture of Wallemia sebi, Fusarium culmorum, Penicillium chrysogenum, Ulocladium botrytis, and Aspergillus versicolor was inoculated on pine wood and particle board. In Study 1, each of 27 participants took part in two exposure conditions, one with air from molds growing on building materials (low levels of emissions from the building materials and the mold mixture) and one with blank air, both conditions during 60 min. In Study 2, each of 24 participants was exposed (10 min) four times in a 2 x 2 design randomly to air from moldy building materials (high levels) and blank, with and without nose-clip. The participants rated air quality and symptoms before, during, and after each exposure. Self-reported tear-film break-up time and attention and processing speed (Study 1) was also measured. Exposure to high VOC levels increased the reports of perceived poor air quality, and in the condition without nose-clip enhanced skin symptoms were also noted. No such outcome was observed when exposing the participants to low VOC levels. Emissions from building materials caused by dampness and microbial growth may be involved in indoor air health problems. This study showed that exposure to high levels of VOC emitted from damp building materials and a mixture of mold may cause perceived poor air quality. It also indicated that stimulation of chemical warning systems (the nasal chemosensory part of the trigeminal system and the olfactory system) may enhance skin symptoms.

  2. Modeling of interfacial friction damping of carbon nanotube-based nanocomposites

    Science.gov (United States)

    Lin, R. M.; Lu, C.

    2010-11-01

    Carbon nanotube-based composite is becoming increasingly popular and offers great potential for highly demanding practical high strength and high damping applications. The excellent damping capacity of CNTs is primarily due to the interfacial friction between carbon nanotubes and polymer resins and the extremely large interfacial surface area over a given specific mass (specific area). In this paper, damping characteristics of carbon nanotube-based composites have been investigated, with an objective of developing an effective and accurate analytical model, which can be used as a design tool for the damping design of such materials. Based on the interfacial slips between the resin and nanotubes and between the nanotubes themselves, a micro stick-slip damping model has been developed. Such a physically derived model is believed to be appropriate and representative of the actual complex damping mechanism of the material system. The model, developed for the first time, is analytical and relates explicitly the material properties of the resin and nanotubes and the processing parameters to the overall material damping loss factor and hence it offers the possibility for material engineers to possibly optimize the damping for required applications. Due to the nonlinear force-displacement relationship derived under the micro stick-slip, a harmonic linearization method, the Describing Function method, has been employed to analyse its vibration characteristics and to derive the required damping loss factors. From the analytical formula, it can be seen that the damping loss factor of the material system depends on the individual material properties of the resin and the nanotubes, structural deformation, nanotube volume fraction and the critical shear stresses at which interfacial slips take place. By taking careful considerations of these design parameters, optimized carbon nanotube-based composites for advanced damping applications can be developed. Extensive numerical

  3. The vibration damping effectiveness of an active seat suspension system and its robustness to varying mass loading

    Science.gov (United States)

    Maciejewski, I.; Meyer, L.; Krzyzynski, T.

    2010-09-01

    The paper describes the simulated dynamic response of an active vibro-isolating pneumatic suspension seat. Active control of the air-spring force is used to improve its vibro-isolation properties. For the active vibration isolating system described, a triple feedback loop control system was developed and analysed. The system robustness for different load masses was investigated using the verified active seat suspension model. The Seat Effective Amplitude Transmissibility factor (SEAT) and the maximum suspension deflection were used as the seat performance indices.

  4. Control concept for piezo-based actuator-sensor-units for uniaxial vibration damping in machine tools

    OpenAIRE

    Neugebauer, Reimund; Pagel, K.; Bucht, A; Wittstock, V.; Pappe, A.

    2010-01-01

    Additional piezo-based components in drive trains can significantly improve the dynamic behaviour of machine tools. In this article we present a piezo-based actuator-sensor-unit that is able to reduce uniaxial vibrations in ball screw driven feed axis of machine tools. A complex model of a feed axis including ASU was developed to design a controller. The control concept is based on the direct velocity feedback. A modular test bench was designed, assembled and investigated to verify the ASU's ...

  5. Analysis of enhanced modal damping ratio in porous materials using an acoustic-structure interaction model

    DEFF Research Database (Denmark)

    Kook, Junghwan; Jensen, Jakob Søndergaard

    2014-01-01

    relation expressing how an increased damping due to the acoustic medium surrounding the microbeam affect the MDR of the macrobeam. We further analyze the effect of including dissipation of the acoustic medium by using finite element (FE) analysis with acoustic-structure interaction (ASI) using a simple...

  6. Improvement of viscoelastic damping in nickel aluminum bronze by indium-tin

    Science.gov (United States)

    Lee, Taeyong

    2011-06-01

    Reduction of the vibration noise from submarine propellers is of interest in naval operations. Such an objective can be achieved via the use of materials with the ability to dissipate energy of vibration by means of heat, i.e. high damping materials. An additional problem is that the extreme hydrostatic pressure environment of a submarine requires the chosen material to exhibit considerably high stiffness. Most materials demonstrate a compromise between the two properties, i.e. stiffness and damping. This paper aims to discuss research into high stiffness and high damping materials conducted using a dynamic mechanical analyzer (DMA) under variations of testing temperature, frequency, and strain amplitude. Alloys of nickel aluminum bronze and indium tin are the subjects of this study. Defect damping represents a large portion of the overall damping properties of the nickel aluminum bronze while increasing indium content is shown to boost the damping properties of the indium tin alloy. The study then continues with the development of a new material that combines both indium alloying and defects introduction into the nickel aluminum bronze alloy. The new alloy is observed to have high damping, as measured in its high tan δ, with minimum reduction of the stiffness | E*|.

  7. Topological material layout in plates for vibration suppression and wave propagation control

    DEFF Research Database (Denmark)

    Larsen, Anders Astrup; Laksafoss, B.; Jensen, Jakob Søndergaard

    2009-01-01

    plate theory coupled with analytical sensitivity analysis using the adjoint method and an iterative design update procedure based on a mathematical programming tool. We demonstrate the capability of the method by designing bi-material plates that, when subjected to harmonic excitation, either......We propose a topological material layout method to design elastic plates with optimized properties for vibration suppression and guided transport of vibration energy. The gradient-based optimization algorithm is based on a finite element model of the plate vibrations obtained using the Mindlin...... effectively suppress the overall vibration level or alternatively transport energy in predefined paths in the plates, including the realization of a ring wave device....

  8. Turbojet engine blade damping

    Science.gov (United States)

    Srinivasan, A. V.; Cutts, D. G.; Sridhar, S.

    1981-01-01

    The potentials of various sources of nonaerodynamic damping in engine blading are evaluated through a combination of advanced analysis and testing. The sources studied include material hysteresis, dry friction at shroud and root disk interfaces as well as at platform type external dampers. A limited seris of tests was conducted to evaluate damping capacities of composite materials (B/AL, B/AL/Ti) and thermal barrier coatings. Further, basic experiments were performed on titanium specimens to establish the characteristics of sliding friction and to determine material damping constants J and n. All the tests were conducted on single blades. Mathematical models were develthe several mechanisms of damping. Procedures to apply this data to predict damping levels in an assembly of blades are developed and discussed.

  9. Non-Linear Finite Element Analysis of Viscoelastic Materials

    National Research Council Canada - National Science Library

    Negaard, Gordon

    1998-01-01

    .... It would be useful if viscoelastic materials could be used to damp the vibration of such structures, however the behavior of a viscoelastic material in an extremely high g-loading is not well understood...

  10. Quadratic Damping

    Science.gov (United States)

    Fay, Temple H.

    2012-01-01

    Quadratic friction involves a discontinuous damping term in equations of motion in order that the frictional force always opposes the direction of the motion. Perhaps for this reason this topic is usually omitted from beginning texts in differential equations and physics. However, quadratic damping is more realistic than viscous damping in many…

  11. Fixation system with high-efficiency vibration damping for titanium milling. Chip removal; Werkzeugspannsystem mit hoher Vibrationsdaempfung zur Titanbearbeitung. Schwerzerspanung

    Energy Technology Data Exchange (ETDEWEB)

    Broennimann, Martin [Rego-Fix AG, Tenniken (Switzerland)

    2009-06-08

    Difficult materials like titanium are common in the aerospace industry. With a high-efficiency fixation system and an optimized milling strategy, propulsion system producer MTU was able to enhance productivity in titanium blisk production. The working time was reduced by 42 % and the tool cost by 76 %. (orig.)

  12. Active and passive damping based on piezoelectric elements -controllability issues-

    NARCIS (Netherlands)

    Holterman, J.; de Vries, Theodorus J.A.; van Amerongen, J.; Jonker, Jan B.; Jonker, J.B.

    2001-01-01

    Piezoelectric elements are widely used for damping micro-vibrations in mechanical structures. Active damping can be realised robustly by means of collocated actuator-sensor-pairs, controlled so as to extract vibration energy. Excellent damping performance is possible as long as sufficient

  13. Viscoelastic material properties’ identification using high speed full field measurements on vibrating plates

    Directory of Open Access Journals (Sweden)

    Pierron F.

    2010-06-01

    Full Text Available The paper presents an experimental application of a method leading to the identification of the elastic and damping material properties of isotropic vibrating plates. The theory assumes that the searched parameters can be extracted from curvature and deflection fields measured on the whole surface of the plate at two particular instants of the vibrating motion. The experimental application consists in an original excitation fixture, a particular adaptation of an optical full-field measurement technique, a data preprocessing giving the curvature and deflection fields and finally in the identification process using the Virtual Fields Method (VFM. The principle of the deflectometry technique used for the measurements is presented. First results of identification on an acrylic plate are presented and compared to reference values. Details about a new experimental arrangement, currently in progress, is presented. It uses a high speed digital camera to over sample the full-field measurements.

  14. Nonlinear vibration absorption for a flexible arm via a virtual vibration absorber

    Science.gov (United States)

    Bian, Yushu; Gao, Zhihui

    2017-07-01

    A semi-active vibration absorption method is put forward to attenuate nonlinear vibration of a flexible arm based on the internal resonance. To maintain the 2:1 internal resonance condition and the desirable damping characteristic, a virtual vibration absorber is suggested. It is mathematically equivalent to a vibration absorber but its frequency and damping coefficients can be readily adjusted by simple control algorithms, thereby replacing those hard-to-implement mechanical designs. Through theoretical analyses and numerical simulations, it is proven that the internal resonance can be successfully established for the flexible arm, and the vibrational energy of flexible arm can be transferred to and dissipated by the virtual vibration absorber. Finally, experimental results are presented to validate the theoretical predictions. Since the proposed method absorbs rather than suppresses vibrational energy of the primary system, it is more convenient to reduce strong vibration than conventional active vibration suppression methods based on smart material actuators with limited energy output. Furthermore, since it aims to establish an internal vibrational energy transfer channel from the primary system to the vibration absorber rather than directly respond to external excitations, it is especially applicable for attenuating nonlinear vibration excited by unpredictable excitations.

  15. Noise Abatement and Internal Vibrational Absorption in Potential Structural Materials

    Science.gov (United States)

    1976-11-01

    as advertising nor IS an officirl indorument or rpprovrl of such products or companies by the United Strtos Government. DISPOSITION INSTRUCTIONS...made from the high damping iron-chromium-aluminum alloy were obtained from Toshiba Electric Company. The plates have been delivered and are...distributed _ by Toshiba Electric Co. (17) on a proprietary Fe-Cr-Al alloy and the existence of a miscribility gap in the Fe - Cr system shown in

  16. Resonant Electromagnetic Shunt Damping of Flexible Structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker

    2016-01-01

    Electromagnetic transducers convert mechanical energy to electrical energy and vice versa. Effective passive vibration damping of flexible structures can therefore be introduced by shunting with an accurately calibrated resonant electrical network thatcontains a capacitor to create the desired...... resonance and a resistor to dissipate the correct amount of vibration energy. The modal interaction with residual vibration forms not targeted by the resonant shunt is represented by supplemental flexibility and inertia terms. This leads to modified calibration formulae that maintain the desired damping...

  17. Linear control strategies for damping of flexible structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Riess; Krenk, Steen

    2006-01-01

    Starting from the two-component representation technique for damping of structures the possible increase in damping efficiency obtained by introducing collocated active damping is illustrated. The two-component representation of the damped vibration mode is constructed as a linear combination of ...

  18. Tactile Perception of Roughness and Hardness to Discriminate Materials by Friction-Induced Vibration

    National Research Council Canada - National Science Library

    Shuyang Ding; Yunlu Pan; Mingsi Tong; Xuezeng Zhao

    2017-01-01

    ... skin. The tactile perception of surface roughness and material hardness can be estimated by skin vibrations generated during a fingertip stroking of a surface instead of being maintained in a static position...

  19. Investigation of sandwich material surface created by abrasive water jet (AWJ via vibration emission

    Directory of Open Access Journals (Sweden)

    P. Hreha

    2014-01-01

    Full Text Available The paper presents research a of abrasive waterjet cutting of heterogeneous “sandwich“ material with different Young modulus of elasticity of the cutted surface geometry by means of vibration emission. In order to confirm hypothetical assumptions about direct relation between vibration emission and surface quality an experiment in heterogeneous material consisting of stainless steel (DIN 1.4006 / AISI 410 and alloy AlCuMg2 has been provided.

  20. Feedback of electronic components in local control strategies for active vibration damping of adaptive structures; Einfluss elektronischer Komponenten bei lokalen Regelungsverfahren zur aktiven Schwingungsdaempfung adaptiver Strukturen

    Energy Technology Data Exchange (ETDEWEB)

    Lay, A.

    2000-07-01

    This thesis deals with the direct velocity feedback (DVF) and the positive position feedback (PPF) two so-called local control strategies (LAC) for active vibration damping of structures. The influence of the dynamics of the components needed for technical realization on the control performance is investigated. Piezoelectric ceramics are used as actuators and sensors. An integral procedure is chosen so the aspects structural mechanics, control theory, measuring technique, the electrical engineering and digital signalprocessing are taken into account, since only the consideration of all components, their characteristics and the their reciprocal interaction leads to an optimal system. For both control strategies the influence of the dynamics of the actuator and sensor amplifiers, the analog lowpass filter and the digitization is investigated. The investigations show that it is absolutely necessary to consider the dynamics of the components. Otherwise DVF can only be used restrictively. Using PPF, these additional dynamics limit the parameters during the control design. The investigations further show, that knowing the poles and the zeros of the structure is of crucial importance. The results of the investigations are collected in guidelines choosing the components and the control design, respectively. The experiments corroborate the investigations and show the potential of the local control strategies. PPF is to be preferred to DVF because of its better robustness against additional dynamics. (orig.) [German] Die vorliegende Arbeit befasst sich mit der Untersuchung des Einflusses der Dynamik der zur technischen Realisierung erforderlichen Komponenten bei der direkten Geschwindigkeitsrueckfuehrung (DVF) und der positiven Postitionsrueckfuehrung (PPF), zwei lokalen Regelungsverfahren zur aktiven Schwingungsdaempfung von Strukturen. Als Aktoren und Sensoren werden piezoelektrische Materialien verwendet. Gewaehlt wird ein integrales Vorgehen, um die Aspekte der

  1. Coulomb Damping

    Science.gov (United States)

    Fay, Temple H.

    2012-01-01

    Viscous damping is commonly discussed in beginning differential equations and physics texts but dry friction or Coulomb friction is not despite dry friction being encountered in many physical applications. One reason for avoiding this topic is that the equations involve a jump discontinuity in the damping term. In this article, we adopt an energy…

  2. Influence of vibrational treatment on thermomechanical response of material under conditions identical to friction stir welding

    Energy Technology Data Exchange (ETDEWEB)

    Konovalenko, Ivan S., E-mail: ivkon@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Konovalenko, Igor S., E-mail: igkon@ispms.tsc.ru; Kolubaev, Evgeniy A., E-mail: eak@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); Dmitriev, Andrey I., E-mail: dmitr@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation); Psakhie, Sergey G., E-mail: sp@ms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation)

    2015-10-27

    A molecular dynamics model was constructed to describe material loading on the atomic scale by the mode identical to friction stir welding. It was shown that additional vibration applied to the tool during the loading mode provides specified intensity values and continuous thermomechanical action during welding. An increase in additional vibration intensity causes an increase both in the force acting on the workpiece from the rotating tool and in temperature within the welded area.

  3. Modelling of Dampers and Damping in Structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Riess

    2006-01-01

    The present thesis consists of an extended summary and four papers concerning damping of structures and algorithmic damping in numerical analysis. The first part of the thesis deals with the efficiency and the tuning of external collocated dampers acting on flexible structures. The dynamics......, and thereby the damping, of flexible structures are generally described in terms of the dominant vibration modes. A system reduction technique, where the damped vibration mode is constructed as a linear combination of the undamped mode shape and the mode shape obtained by locking the damper, is applied....... This two-component representation leads to a simple solution for the modal damping representing the natural frequency and the associated damping ratio. It appears from numerical examples that this system reduction technique provides very accurate results. % Analytical expressions for the optimal tuning...

  4. Air damping effect on the air-based CMUT operation

    Science.gov (United States)

    Cha, Bu-Sang; Kanashima, Takeshi; Lee, Seung-Mok; Okuyama, Masanori

    2015-08-01

    The vibration amplitude, damping ratio and viscous damping force in capacitive micromachinedultrasonic transducers (CMUTs) with a perforated membrane have been calculated theoretically and compared with the experimental data on its vibration behavior. The electrical bias of the DC and the AC voltages and the operation frequency conditions influence the damping effect because leads to variations in the gap height and the vibration velocity of the membrane. We propose a new estimation method to determine the damping ratio by the decay rate of the vibration amplitudes of the perforated membrane plate are measured using a laser vibrometer at each frequency, and the damping ratios were calculated from those results. The influences of the vibration frequency and the electrostatic force on the damping effect under the various operation conditions have been studied.

  5. Resonant Electromagnetic Shunt Damping of Flexible Structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker

    2016-01-01

    Electromagnetic transducers convert mechanical energy to electrical energy and vice versa. Effective passive vibration damping of flexible structures can therefore be introduced by shunting with an accurately calibrated resonant electrical network thatcontains a capacitor to create the desired...

  6. Intelligent damping layer under a plate subjected to a pair of masses moving in opposite directions

    Science.gov (United States)

    Bajer, Czesław; Pisarski, Dominik; Szmidt, Tomasz; Dyniewicz, Bartłomiej

    2017-04-01

    Reducing displacements of a plate vibrating under a pair of masses traveling in opposite directions can be improved by adding a smart subsoil instead of a classical damping layer. We propose a material that acts according to the instantaneous state of the plate, i.e., its displacements and velocity. Such an intelligent damping layer reduces vertical displacements even by 40%-60%, depending on the type of load and the assumed objective function. Existing materials enable the application of the proposed layer in a semi-active mode. The passive mode can be applied with materials exhibiting direction-dependent viscosity.

  7. The Comparative Study of Vibration Control of Flexible Structure Using Smart Materials

    Directory of Open Access Journals (Sweden)

    Juntao Fei

    2010-01-01

    Full Text Available Considerable attention has been devoted to active vibration control using intelligent materials as PZT actuators. This paper presents results on active control schemes for vibration suppression of flexible steel cantilever beam with bonded piezoelectric actuators. The PZT patches are surface bonded near the fixed end of flexible steel cantilever beam. The dynamic model of the flexible steel cantilever beam is derived. Active vibration control methods: optimal PID control, strain rate feedback control (SRF, and positive position feedback control (PPF are investigated and implemented using xPC Target real-time system. Experimental results demonstrate that the SRF and PPF controls have better performance in suppressing the vibration of cantilever steel beam than the optimal PID control.

  8. Inflammation-associated gene expression in RAW 264.7 macrophages induced by toxins from fungi common on damp building materials.

    Science.gov (United States)

    Rand, Thomas G; Chang, Carolyn T; McMullin, David R; Miller, J David

    2017-09-01

    Most fungi that grow on damp building materials produce low molecular weight compounds, some of which are known to be toxic. In this study, we tested the hypothesis that exposure to some metabolites of fungi common on damp building materials would result in time-, dose-, and compound-specific responses in the production of various chemokines by RAW 264.7 cells. Cell cultures were exposed to a 10 -7 M or 10 -8 M metabolite dose for 2, 4, 8 or 24h. Metabolite concentrations used were based on those that might be expected in alveolar macrophages due to inhalation exposure from living or working in a damp building. Compared to controls, exposure provoked significant time-, dose- and compound-specific responses manifest as differentially elevated secretion of three of nine cytokines tested in culture supernatant of treated cells. The greatest number of cytokines produced in response to the metabolites tested were in andrastin A-treated cells (GM-CSF, TGFβ1, Tnf-α) followed by koninginin A (TGFβ1 and Tnf-α) and phomenone (GM-CSF, TGFβ1). Chaetoglobosin A, chaetomugilin D and walleminone exposures each resulted in significant time-specific production of Tnf-α only. This investigation adds to a body of evidence supporting the role of low molecular weight compounds from damp building materials as pathogen associated molecular patterns (PAMPs). Along with fungal glucan and chitin, these compounds contribute to the non-allergy based respiratory outcomes for people living and working in damp buildings. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Vibro-levitation and inverted pendulum: parametric resonance in vibrating droplets and soft materials.

    Science.gov (United States)

    Ramachandran, Rahul; Nosonovsky, Michael

    2014-07-14

    The phenomenon of liquid droplets "levitating" or bouncing off a liquid vibrating surface has attracted attention of scientists due to its possible application in microfluidics and novel nanostructured superhydrophobic materials. Several models have been suggested in the literature, and the effect is usually attributed to non-linear viscosity. Here we suggest a simple model relating the effect to the parametric resonance as described by the Mathieu equation, which explains stabilization of an inverted pendulum with vibration foundation. Small fast vibrations can be substituted by an effective "levitation" force. We present modeling and experimental results for oil droplets and discuss how the mathematical separation of the slow and fast motion provides insights on the relation of vibro-levitation of oil droplets and soft materials with the vibro-stabilization of an inverted pendulum, and the "Indian rope" and "Cornstarch monster" tricks.

  10. Vibration measurement on composite material with embedded optical fiber based on phase-OTDR

    Science.gov (United States)

    Franciscangelis, C.; Margulis, W.; Floridia, C.; Rosolem, J. B.; Salgado, F. C.; Nyman, T.; Petersson, M.; Hallander, P.; Hällstrom, S.; Söderquist, I.; Fruett, F.

    2017-04-01

    Distributed sensors based on phase-optical time-domain reflectometry (phase-OTDR) are suitable for aircraft health monitoring due to electromagnetic interference immunity, small dimensions, low weight and flexibility. These features allow the fiber embedment into aircraft structures in a nearly non-intrusive way to measure vibrations along its length. The capability of measuring vibrations on avionics structures is of interest for what concerns the study of material fatigue or the occurrence of undesirable phenomena like flutter. In this work, we employed the phase-OTDR technique to measure vibrations ranging from some dozens of Hz to kHz in two layers of composite material board with embedded polyimide coating 0.24 numerical aperture single-mode optical fiber.

  11. Transverse Vibration of Axially Moving Functionally Graded Materials Based on Timoshenko Beam Theory

    Directory of Open Access Journals (Sweden)

    Suihan Sui

    2015-01-01

    Full Text Available The transverse free vibration of an axially moving beam made of functionally graded materials (FGM is investigated using a Timoshenko beam theory. Natural frequencies, vibration modes, and critical speeds of such axially moving systems are determined and discussed in detail. The material properties are assumed to vary continuously through the thickness of the beam according to a power law distribution. Hamilton’s principle is employed to derive the governing equation and a complex mode approach is utilized to obtain the transverse dynamical behaviors including the vibration modes and natural frequencies. Effects of the axially moving speed and the power-law exponent on the dynamic responses are examined. Some numerical examples are presented to reveal the differences of natural frequencies for Timoshenko beam model and Euler beam model. Moreover, the critical speed is determined numerically to indicate its variation with respect to the power-law exponent, axial initial stress, and length to thickness ratio.

  12. Localization and instability in sheared granular materials: Role of friction and vibration

    Science.gov (United States)

    Kothari, Konik R.; Elbanna, Ahmed E.

    2017-02-01

    Shear banding and stick-slip instabilities have been long observed in sheared granular materials. Yet, their microscopic underpinnings, interdependencies, and variability under different loading conditions have not been fully explored. Here we use a nonequilibrium thermodynamics model, the Shear Transformation Zone theory, to investigate the dynamics of strain localization and its connection to stability of sliding in sheared, dry, granular materials. We consider frictional and frictionless grains as well as the presence and absence of acoustic vibrations. Our results suggest that at low and intermediate strain rates, persistent shear bands develop only in the absence of vibrations. Vibrations tend to fluidize the granular network and delocalize slip at these rates. Stick-slip is observed only for frictional grains, and it is confined to the shear band. At high strain rates, stick-slip disappears and the different systems exhibit similar stress-slip response. Changing the vibration intensity, duration or time of application alters the system response and may cause long-lasting rheological changes. We analyze these observations in terms of possible transitions between rate strengthening and rate weakening response facilitated by a competition between shear-induced dilation and vibration-induced compaction. We discuss the implications of our results on dynamic triggering, quiescence, and strength evolution in gouge-filled fault zones.

  13. Determining shear modulus of thin wood composite materials using a cantilever beam vibration method

    Science.gov (United States)

    Cheng Guan; Houjiang Zhang; John F. Hunt; Haicheng Yan

    2016-01-01

    Shear modulus (G) of thin wood composite materials is one of several important indicators that characterizes mechanical properties. However, there is not an easy method to obtain this value. This study presents the use of a newly developed cantilever beam free vibration test apparatus to detect in-plane G of thin wood composite...

  14. Thermal Buckling and Free Vibration Analysis of Heated Functionally Graded Material Beams

    OpenAIRE

    Khalane Sanjay Anandrao; R. K. Gupta; P. Ramachandran; G. V. Rao

    2013-01-01

    The effect of temperature dependency of material properties on thermal buckling and free vibration of functionally graded material (FGM) beams is studied. The FGM beam is assumed to be at a uniform through thickness temperature, above the ambient temperature. Finite element system of equations based on the first order shear deformation theory is developed. FGM beam with axially immovable ends having the classical boundary conditions is analysed. An exhaustive set of numerical results, in term...

  15. Forced Vibration of Timoshenko Beams Made of Multimodular Materials.

    Science.gov (United States)

    1983-06-01

    Piecewise Linear Approximation of a Nonlinear Constitutive Equation", AIAA JournaZ, Vol. 12, No. 6, June 1974, pp. 868-870. 9. Ramberg , W. and Osgood ...this problem. Durban and Baruch [8) used a floating piecewise linear approximation to construct the two "best" straight lines approximatingthe Ramberg ... Osgood stress-strain relation [9]. Bert and Kunar [10] recently presented experimental stress-strain curves 3 for unidirectional cord-rubber materials

  16. Fatigue failure of materials under broad band random vibrations

    Science.gov (United States)

    Huang, T. C.; Lanz, R. W.

    1971-01-01

    The fatigue life of material under multifactor influence of broad band random excitations has been investigated. Parameters which affect the fatigue life are postulated to be peak stress, variance of stress and the natural frequency of the system. Experimental data were processed by the hybrid computer. Based on the experimental results and regression analysis a best predicting model has been found. All values of the experimental fatigue lives are within the 95% confidence intervals of the predicting equation.

  17. Control Application of Piezoelectric Materials to Aeroelastic Self-Excited Vibrations

    Directory of Open Access Journals (Sweden)

    Mohammad Amin Rashidifar

    2014-01-01

    Full Text Available A method for application of piezoelectric materials to aeroelasticity of turbomachinery blades is presented. The governing differential equations of an overhung beam are established. The induced voltage in attached piezoelectric sensors due to the strain of the beam is calculated. In aeroelastic self-excited vibrations, the aerodynamic generalized force of a specified mode can be described as a linear function of the generalized coordinate and its derivatives. This simplifies the closed loop system designed for vibration control of the corresponding structure. On the other hand, there is an industrial interest in measurement of displacement, velocity, acceleration, or a contribution of them for machinery condition monitoring. Considering this criterion in quadratic optimal control systems, a special style of performance index is configured. Utilizing the current relations in an aeroelastic case with proper attachment of piezoelectric elements can provide higher margin of instability and lead to lower vibration magnitude.

  18. Vibration analysis of multi-phase nanocrystalline material nanoshells using strain gradient elasticity

    Science.gov (United States)

    Barati, Mohammad Reza

    2017-10-01

    This paper studies the free vibrational behavior of porous nanocrystalline silicon nanoshells using strain gradient theory. Nanocrystalline materials are multi-phase composites with the contribution of nanopores, nanograins and interface phase. Because of experimental observation of strain gradients near the interface phase, the nanoshell is modeled via strain gradient theory. A micromechanical model based on the Mori–Tanaka scheme is employed to incorporate the size of nanograins/nanopores and their surface energies. The nanoshell is modeled via first order shear deformation theory and Galerkin’s method is implemented to obtain vibration frequencies. Shape functions that satisfy available classical and non-classical boundary conditions in strain gradient theory are proposed. It is shown that the vibrational behavior of the nanoshell is influenced by the porosity percentage, nanograin size, strain gradient coefficient, boundary conditions, and the surface phase of nanograins/nanopores.

  19. Damage-free vibrational spectroscopy of biological materials in the electron microscope.

    Science.gov (United States)

    Rez, Peter; Aoki, Toshihiro; March, Katia; Gur, Dvir; Krivanek, Ondrej L; Dellby, Niklas; Lovejoy, Tracy C; Wolf, Sharon G; Cohen, Hagai

    2016-03-10

    Vibrational spectroscopy in the electron microscope would be transformative in the study of biological samples, provided that radiation damage could be prevented. However, electron beams typically create high-energy excitations that severely accelerate sample degradation. Here this major difficulty is overcome using an 'aloof' electron beam, positioned tens of nanometres away from the sample: high-energy excitations are suppressed, while vibrational modes of energies <1 eV can be 'safely' investigated. To demonstrate the potential of aloof spectroscopy, we record electron energy loss spectra from biogenic guanine crystals in their native state, resolving their characteristic C-H, N-H and C=O vibrational signatures with no observable radiation damage. The technique opens up the possibility of non-damaging compositional analyses of organic functional groups, including non-crystalline biological materials, at a spatial resolution of ∼10 nm, simultaneously combined with imaging in the electron microscope.

  20. Aeroelastic vibrations and stability of plates and shells

    CERN Document Server

    Algazin, Sergey D

    2015-01-01

    Back-action of wind onto wings causes vibrations, endangering the whole structure. By careful choices of geometry, materials and damping, hazardous effects on wind engines, planes, turbines and cars can be avoided. This book gives an overview of aerodynamics and mechanics behind these problems and describes a range of mechanical effects. Numerical and analytical met

  1. Parallel calculations of vibrational properties in complex materials: negative thermal expansion and elastic inhomogeneity

    Science.gov (United States)

    Vila, F. D.; Rehr, J. J.

    Effects of thermal vibrations are essential to obtain a more complete understanding of the properties of complex materials. For example, they are important in the analysis and simulation of x-ray absorption spectra (XAS). In previous work we introduced an ab initio approach for a variety of vibrational effects, such as crystallographic and XAS Debye-Waller factors, Debye and Einstein temperatures, and thermal expansion coefficients. This approach uses theoretical dynamical matrices from which the locally-projected vibrational densities of states are obtained using a Lanczos recursion algorithm. In this talk I present recent improvements to our implementation, which permit simulations of more complex materials with up to two orders of magnitude larger simulation cells. The method takes advantage of parallelization in calculations of the dynamical matrix with VASP. To illustrate these capabilities we discuss two problems of considerable interest: negative thermal expansion in ZrW2O8; and local inhomogeneities in the elastic properties of supported metal nanoparticles. Both cases highlight the importance of a local treatment of vibrational properties. Supported by DOE Grant DE-FG02-03ER15476, with computer support from DOE-NERSC.

  2. Anisotropic damping of Timoshenko beam elements

    DEFF Research Database (Denmark)

    Hansen, M.H.

    2001-01-01

    This report contains a description of a structural damping model for Timoshenko beam elements used in the aeroelastic code HawC developed at Risø for modeling wind turbines. The model has been developed to enable modeling of turbine blades which oftenhave different damping characteristics...... for ¤flapwise¤, ¤edgewise¤ and ¤torsional¤ vibrations. The structural damping forces acting on the beam element are modeled by viscous damping described by an element damping matrix. The composition of this matrix is basedon the element mass and stiffness matrices. It is shown how the coefficients for the mass...... and stiffness contributions can be calibrated to give the desired modal damping in the complete model of a blade....

  3. Vibration Control via Stiffness Switching of Magnetostrictive Transducers

    Science.gov (United States)

    Scheidler, Justin J.; Asnani, Vivake M.; Dapino, Marcelo J.

    2016-01-01

    This paper presents a computational study of structural vibration control that is realized by switching a magnetostrictive transducer between high and low stiffness states. Switching is accomplished by either changing the applied magnetic field with a voltage excitation or changing the shunt impedance on the transducer's coil (i.e., the magnetostrictive material's magnetic boundary condition). Switched-stiffness vibration control is simulated using a lumped mass supported by a damper and the magnetostrictive transducer (mount), which is represented by a nonlinear, electromechanical model. Free vibration of the mass is calculated while varying the mount's stiffness according to a reference switched-stiffness vibration control law. The results reveal that switching the magnetic field produces the desired change in stiffness, but also an undesired actuation force that can significantly degrade the vibration control. Hence, a modified switched-stiffness control law that accounts for the actuation force is proposed and implemented for voltage-controlled stiffness switching. The influence of the magnetomechanical bias condition is also discussed. Voltage-controlled stiffness switching is found to introduce damping equivalent to a viscous damping factor up to about 0.25; this is shown to primarily result from active vibration reduction caused by the actuation force. The merit of magnetostrictive switched-stiffness vibration control is then quantified by comparing the results of voltage- and shunt-controlled stiffness switching to the performance of optimal magnetostrictive shunt damping.

  4. Theory of vibration protection

    CERN Document Server

    Karnovsky, Igor A

    2016-01-01

    This text is an advancement of the theory of vibration protection of mechanical systems with lumped and distributed parameters. The book offers various concepts and methods of solving vibration protection problems, discusses the advantages and disadvantages of different methods, and the fields of their effective applications. Fundamental approaches of vibration protection, which are considered in this book, are the passive, parametric and optimal active vibration protection. The passive vibration protection is based on vibration isolation, vibration damping and dynamic absorbers. Parametric vibration protection theory is based on the Shchipanov-Luzin invariance principle. Optimal active vibration protection theory is based on the Pontryagin principle and the Krein moment method. The book also contains special topics such as suppression of vibrations at the source of their occurrence and the harmful influence of vibrations on humans. Numerous examples, which illustrate the theoretical ideas of each chapter, ar...

  5. Dissipative properties of materials with microplastic mechanism of damping under conditions of separate and joint action of static stresses and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Shpak, D.E.

    1985-01-01

    Static stress and temperature are studied experimentally for their separate and joint effect on dissipative properties of VT3-1 and Ehp 718 alloys whose dissipation energy is conditioned by microplastic strains. The results of the study are presented. It is shown that for the materials studied in contrast to the materials with other basic damping mechanisms joint effect of static stresses and temperature is close to a simple summation of the separate effect of these factors without any changes in the character of energy dissipation dependence.

  6. Optimal design of damping layers in SMA/GFRP laminated hybrid composites

    Science.gov (United States)

    Haghdoust, P.; Cinquemani, S.; Lo Conte, A.; Lecis, N.

    2017-10-01

    This work describes the optimization of the shape profiles for shape memory alloys (SMA) sheets in hybrid layered composite structures, i.e. slender beams or thinner plates, designed for the passive attenuation of flexural vibrations. The paper starts with the description of the material and architecture of the investigated hybrid layered composite. An analytical method, for evaluating the energy dissipation inside a vibrating cantilever beam is developed. The analytical solution is then followed by a shape profile optimization of the inserts, using a genetic algorithm to minimize the SMA material layer usage, while maintaining target level of structural damping. Delamination problem at SMA/glass fiber reinforced polymer interface is discussed. At the end, the proposed methodology has been applied to study the hybridization of a wind turbine layered structure blade with SMA material, in order to increase its passive damping.

  7. Energy trapping of thickness-shear vibration modes of elastic plates with functionally graded materials.

    Science.gov (United States)

    Wang, Ji; Yang, Jiashi; Li, Jiangyu

    2007-03-01

    Energy trapping has important applications in the design of thickness-shear resonators. Considerable efforts have been made for the effective utilization and improvement of energy trapping with variations of plate configurations, such as adding electrodes and contouring. As a new approach in seeking improved energy trapping feature, we analyze thickness-shear vibrations in an elastic plate with functionally graded material (FGM) of in-plane variation of mechanical properties, such as elastic constants and density. A simple and general equation governing the thickness-shear modes is derived from a variational analysis. A plate with piecewise constant material properties is analyzed as an example. It is shown that such a plate can support thickness-shear vibration modes with obvious energy trapping. Bechmann's number for the existence of only one trapped mode also can be determined accordingly.

  8. An experimental study of ultrasonic vibration and the penetration of granular material

    Science.gov (United States)

    Firstbrook, David; Worrall, Kevin; Timoney, Ryan; Suñol, Francesc; Gao, Yang

    2017-01-01

    This work investigates the potential use of direct ultrasonic vibration as an aid to penetration of granular material. Compared with non-ultrasonic penetration, required forces have been observed to reduce by an order of magnitude. Similarly, total consumed power can be reduced by up to 27%, depending on the substrate and ultrasonic amplitude used. Tests were also carried out in high-gravity conditions, displaying a trend that suggests these benefits could be leveraged in lower gravity regimes. PMID:28293134

  9. Passive damping concepts for slender columns in space structures

    Science.gov (United States)

    Razzaq, Z.; Ekhelikar, R. K.

    1985-01-01

    An experimental and theoretical study of three different passive damping concepts is conducted for a slender member with partial rotational end restraints. Over a hundred full-scale natural vibration experiments were conducted to evaluate the effectiveness of mass-string, polyethylene tubing, and chain damping concepts. The damping properties obtained from the experiments were used in the approximate analyses based on the partial differential equation of motion for the problem. The comparison of the experimental and the theoretical deflection-time relations shows that the velocity-dependent damping model used in the theory is adequate. From the experimental results, the effect of end connection friction and induced axial forces on damping is identified. The definition of an efficiency index is proposed based on the damping ratio and the mass of a given passive damping device. Using this definition, the efficiencies of the three damping devices are compared. The polyethylene tubing concept resulted into a low damping efficiency.

  10. Tactile Perception of Roughness and Hardness to Discriminate Materials by Friction-Induced Vibration.

    Science.gov (United States)

    Ding, Shuyang; Pan, Yunlu; Tong, Mingsi; Zhao, Xuezeng

    2017-11-28

    The human fingertip is an exquisitely powerful bio-tactile sensor in perceiving different materials based on various highly-sensitive mechanoreceptors distributed all over the skin. The tactile perception of surface roughness and material hardness can be estimated by skin vibrations generated during a fingertip stroking of a surface instead of being maintained in a static position. Moreover, reciprocating sliding with increasing velocities and pressures are two common behaviors in humans to discriminate different materials, but the question remains as to what the correlation of the sliding velocity and normal load on the tactile perceptions of surface roughness and hardness is for material discrimination. In order to investigate this correlation, a finger-inspired crossed-I beam structure tactile tester has been designed to mimic the anthropic tactile discrimination behaviors. A novel method of characterizing the fast Fourier transform integral (FFT) slope of the vibration acceleration signal generated from fingertip rubbing on surfaces at increasing sliding velocity and normal load, respectively, are defined as k v and k w , and is proposed to discriminate the surface roughness and hardness of different materials. Over eight types of materials were tested, and they proved the capability and advantages of this high tactile-discriminating method. Our study may find applications in investigating humanoid robot perceptual abilities.

  11. Tactile Perception of Roughness and Hardness to Discriminate Materials by Friction-Induced Vibration

    Directory of Open Access Journals (Sweden)

    Shuyang Ding

    2017-11-01

    Full Text Available The human fingertip is an exquisitely powerful bio-tactile sensor in perceiving different materials based on various highly-sensitive mechanoreceptors distributed all over the skin. The tactile perception of surface roughness and material hardness can be estimated by skin vibrations generated during a fingertip stroking of a surface instead of being maintained in a static position. Moreover, reciprocating sliding with increasing velocities and pressures are two common behaviors in humans to discriminate different materials, but the question remains as to what the correlation of the sliding velocity and normal load on the tactile perceptions of surface roughness and hardness is for material discrimination. In order to investigate this correlation, a finger-inspired crossed-I beam structure tactile tester has been designed to mimic the anthropic tactile discrimination behaviors. A novel method of characterizing the fast Fourier transform integral (FFT slope of the vibration acceleration signal generated from fingertip rubbing on surfaces at increasing sliding velocity and normal load, respectively, are defined as kv and kw, and is proposed to discriminate the surface roughness and hardness of different materials. Over eight types of materials were tested, and they proved the capability and advantages of this high tactile-discriminating method. Our study may find applications in investigating humanoid robot perceptual abilities.

  12. Modified inelastic bouncing ball model for describing the dynamics of granular materials in a vibrated container

    Science.gov (United States)

    Balista, Junius André F.; Saloma, Caesar

    2015-01-01

    We show that at the onset of convection, the acceleration of a confined granular material is not necessarily equal to that of its vibrated container. Convection happens when the material is able to counter the downward gravitational pull and accelerates at a rate that is equal to the gravitational acceleration g. We modify the Inelastic Bouncing Ball Model and incorporate the transmissibility parameter Tr which measures the efficiency that the external force driving the container is transmitted to the material itself. For a specified Tr value, the material is represented by an inelastic bouncing ball with a time-of-flight T(Γ ;Tr) where Γ =A0ω2 / g, is the dimensionless container acceleration, and A0 and ω are the driving amplitude and angular frequency, respectively. For a given Γ-range, the T(Γ ;Tr) curve provides the bifurcation diagram of the perturbed material and a family of bifurcation diagrams is generated for a set of Tr values. We illustrate that Tr is useful in rationalizing experimental results produced by confined granular materials that is subjected to a range of applied force magnitudes. For the same physical set-up, the force transmission efficiency from the container to the grains may not remain constant as the force strength is varied. The efficiency is also affected by the presence or absence of air in the vibrated container.

  13. Acoustic radiation of damped cylindrical shell with arbitrary thickness in the fluid field

    Science.gov (United States)

    Zhang, Jun-Jie; Li, Tian-Yun; Ye, Wen-Bing; Zhu, Xiang

    2010-12-01

    The insertion loss of acoustic radiation of damped cylindrical shell described by 3-D elasticity Navier equations under radial harmonic applied load in fluid is presented. The classical integral transform technique, potential theory and Lamè resolution are used to derive the solutions of Navier equations. The higher precision inversion computation is introduced to solve the linear equations. Comparing with acoustic radiation of one-layer cylindrical shell, the influence of thickness, mass density, dilatational wave loss factor and Young's modulus of damping material and circumferential mode number of the cylindrical shell on the insertion loss is concluded. The theoretical model in the paper can be used to deal with the arbitrary thickness and any frequency of the coated layer in dynamic problem. The conclusions may be of theoretical reference to the application of damping material to noise and vibration control of submarines and underwater pipes.

  14. The effect of vibration on bed voidage behaviors in fluidized beds with large particles

    Directory of Open Access Journals (Sweden)

    H. Jin

    2007-09-01

    Full Text Available The effects of vibration parameters, operating conditions and material properties on bed voidage were investigated using an optical fiber probe approach in a vibrating fluidized bed with a diameter of 148 mm. Variables studied included frequency (0-282 s-1, amplitude (0 mm-1 mm, bed height (0.1 m-0.4 m as well as four kinds of particles (belonging to Geldart's B and D groups. The axial and radial voidage distribution with vibration is compared with that without vibration, which shows vibration can aid in the fluidization behaviors of particles. For a larger vibration amplitude, the vibration seriously affects bed voidage. The vibration energy can damp out for particle layers with increasing the bed height. According to analysis of experimental data, an empirical correlation for predicting bed voidage, giving good agreement with the experimental data and a deviation within ±15%, was proposed.

  15. Landau damping

    CERN Document Server

    Hofmann, A

    2006-01-01

    Abstract Landau damping is the suppression of an instability by a spread of frequencies in the beam. It is treated here from an experimental point of view. To introduce the concept we consider a set of oscillators having a spread in resonant frequencies !r and calculate the response of their there center-of-mass to an external driving force. A pulse excitation gives each oscillator the same initial velocity but, due to their different frequencies, the center-of-mass motion will decay with time. A harmonic excitation with a frequency ! being inside the distribution in !r results in oscillators responding with different phases and only a few of them having !r ! will grow to large amplitudes and absorb energy. The oscillator response to a pulse excitation, called Green function, and the one to a harmonic excitation, called transfer function, serve as a basis to calculate Landau damping which suppresses an instability at infinitesimal level before any large amplitudes are reached. This is illustrated by a negativ...

  16. Effect of material constants on power output in piezoelectric vibration-based generators.

    Science.gov (United States)

    Takeda, Hiroaki; Mihara, Kensuke; Yoshimura, Tomohiro; Hoshina, Takuya; Tsurumi, Takaaki

    2011-09-01

    A possible power output estimation based on material constants in piezoelectric vibration-based generators is proposed. A modified equivalent circuit model of the generator was built and was validated by the measurement results in the generator fabricated using potassium sodium niobate-based and lead zirconate titanate (PZT) ceramics. Subsequently, generators with the same structure using other PZT-based and bismuth-layered structure ferroelectrics ceramics were fabricated and tested. The power outputs of these generators were expressed as a linear functions of the term composed of electromechanical coupling coefficients k(sys)(2) and mechanical quality factors Q*(m) of the generator. The relationship between device constants (k(sys)(2) and Q*(m)) and material constants (k(31)(2) and Q(m)) was clarified. Estimation of the power output using material constants is demonstrated and the appropriate piezoelectric material for the generator is suggested.

  17. On the impact of damping on the dispersion curves of a locally resonant metamaterial: Modelling and experimental validation

    Science.gov (United States)

    Belle, Lucas Van; Claeys, Claus; Deckers, Elke; Desmet, Wim

    2017-11-01

    Recently, locally resonant metamaterials have come to the fore in noise and vibration control engineering, showing great potential due to their superior noise and vibration attenuation performance in targeted and tunable frequency ranges, referred to as stop bands. Damping has an important influence on the performance of these materials, broadening the frequency range of attenuation at the expense of peak attenuation. As a result, understanding and including the effects of damping is necessary to more accurately predict the attenuation performance of these locally resonant metamaterials. Classically, these often periodic structures are analysed using a unit cell modelling approach to predict wave propagation and thus stop band behaviour, discarding damping. In this work, a unit cell method including damping is used to analyse the complex dispersion curves of a locally resonant metamaterial design. The wave solutions in and around the stop band frequency range are compared to those of the unit cell method discarding damping. The influence on the dispersion curves of damping in resonator and host structure is discussed and the obtained dispersion curves are validated through an experimental dispersion curve measurement based on an Extended Inhomogeneous Wave Correlation method using Scanning Laser Doppler Vibrometry for a metamaterial plate manufactured at a representative scale. Excellent agreement is obtained between the numerically predicted and experimentally retrieved dispersion curves.

  18. Small strain vibration of a continuous, linearized viscoelastic rod of expanded polymer cushion material

    Science.gov (United States)

    Batt, Gregory S.; Gibert, James M.; Daqaq, Mohammed

    2015-08-01

    In this paper, the free and forced vibration response of a linearized, distributed-parameter model of a viscoelastic rod with an applied tip-mass is investigated. A nonlinear model is developed from constitutive relations and is linearized about a static equilibrium position for analysis. A classical Maxwell-Weichert model, represented via a Prony series, is used to model the viscoelastic system. The exact solution to both the free and forced vibration problem is derived and used to study the behavior of an idealized packaging system containing Nova Chemicals' Arcel® foam. It is observed that, although three Prony series terms are deemed sufficient to fit the static test data, convergence of the dynamic response and study of the storage and loss modulii necessitate the use of additional Prony series terms. It is also shown that the model is able to predict the modal frequencies and the primary resonance response at low acceleration excitation, both with reasonable accuracy given the non-homogeneity and density variation observed in the specimens. Higher acceleration inputs result in softening nonlinear responses highlighting the need for a nonlinear elastic model that extends beyond the scope of this work. Solution analysis and experimental data indicate little material vibration energy dissipation close to the first modal frequency of the mass/rod system.

  19. Effect of Wheelchair Frame Material on Users' Mechanical Work and Transmitted Vibration

    Science.gov (United States)

    Aissaoui, Rachid

    2014-01-01

    Wheelchair propulsion exposes the user to a high risk of shoulder injury and to whole-body vibration that exceeds recommendations of ISO 2631-1:1997. Reducing the mechanical work required to travel a given distance (WN-WPM, weight-normalized work-per-meter) can help reduce the risk of shoulder injury, while reducing the vibration transmissibility (VT) of the wheelchair frame can reduce whole-body vibration. New materials such as titanium and carbon are used in today's wheelchairs and are advertised to improve both parameters, but current knowledge on this matter is limited. In this study, WN-WPM and VT were measured simultaneously and compared between six folding wheelchairs (1 titanium, 1 carbon, and 4 aluminium). Ten able-bodied users propelled the six wheelchairs on three ground surfaces. Although no significant difference of WN-WPM was found between wheelchairs (P < 0.1), significant differences of VT were found (P < 0.05). The carbon wheelchair had the lowest VT. Contrarily to current belief, the titanium wheelchair VT was similar to aluminium wheelchairs. A negative correlation between VT and WN-WPM was found, which means that reducing VT may be at the expense of increasing WN-WPM. Based on our results, use of carbon in wheelchair construction seems promising to reduce VT without increasing WN-WPM. PMID:25276802

  20. Assessment of the vibration on the foam legged and sheet metal-legged passenger seat

    Directory of Open Access Journals (Sweden)

    L. Dahil

    2015-10-01

    Full Text Available In this study, it was aim ed to decrease the vibration reaching to passenger from the legs of vehicle seats. In order to determine the levels of vibrations reaching at passengers, a test pad placed under the passenger seat was used, and HVM100 device was used for digitizing the information obtained. By transferring the vibration data to system by using HVM100 device, the acceleration graphics were prepared with Blaze software. As a result, it was determined that the acceleration values of seat legs made of foam material were lower than that of seat legs made of 2 mm thick sheet metal, so they damped the vibration better.

  1. Semi-analytical Vibration Characteristics of Rotating Timoshenko Beams Made of Functionally Graded Materials

    Directory of Open Access Journals (Sweden)

    Farzad Ebrahimia

    Full Text Available AbstractFree vibration analysis of rotating functionally graded (FG thick Timoshenko beams is presented. The material properties of FG beam vary along the thickness direction of the constituents according to power law model. Governing equations are derived through Hamilton's principle and they are solved applying differential transform method. The good agreement between the results of this article and those available in literature validated the presented approach. The emphasis is placed on investigating the effect of several beam parameters such as constituent volume fractions, slenderness ratios, rotational speed and hub radius on natural frequencies and mode shapes of the rotating thick FG beam.

  2. The Application of Vibrational Spectroscopy Techniques in the Qualitative Assessment of Material Traded as Ginseng

    Directory of Open Access Journals (Sweden)

    Maxleene Sandasi

    2016-04-01

    Full Text Available The name “ginseng” is collectively used to describe several plant species, including Panax ginseng (Asian/Oriental ginseng, P. quinquefolius (American ginseng, P. pseudoginseng (Pseudoginseng and Eleutherococcus senticosus (Siberian ginseng, each with different applications in traditional medicine practices. The use of a generic name may lead to the interchangeable use or substitution of raw materials which poses quality control challenges. Quality control methods such as vibrational spectroscopy-based techniques are here proposed as fast, non-destructive methods for the distinction of four ginseng species and the identification of raw materials in commercial ginseng products. Certified ginseng reference material and commercial products were analysed using hyperspectral imaging (HSI, mid-infrared (MIR and near-infrared (NIR spectroscopy. Principal component analysis (PCA and (orthogonal partial least squares discriminant analysis models (OPLS-DA were developed using multivariate analysis software. UHPLC-MS was used to analyse methanol extracts of the reference raw materials and commercial products. The holistic analysis of ginseng raw materials revealed distinct chemical differences using HSI, MIR and NIR. For all methods, Eleutherococcus senticosus displayed the greatest variation from the three Panax species that displayed closer chemical similarity. Good discrimination models with high R2X and Q2 cum vales were developed. These models predicted that the majority of products contained either /P. ginseng or P. quinquefolius. Vibrational spectroscopy and HSI techniques in tandem with multivariate data analysis tools provide useful alternative methods in the authentication of ginseng raw materials and commercial products in a fast, easy, cost-effective and non-destructive manner.

  3. Roughness Parameters Calculation by Means of On-line Vibration Monitoring Emerging from AWJ Interaction with Material

    Czech Academy of Sciences Publication Activity Database

    Hreha, P.; Radvanská, A.; Knapčíková, L.; Krolczyk, G.; Legutko, S.; Królczyk, J. B.; Hloch, Sergej; Monka, P.

    2015-01-01

    Roč. 22, č. 2 (2015), s. 315-326 ISSN 0860-8229 R&D Projects: GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : abrasive water jet * surface topography * material vibration * vibration measurement Subject RIV: JQ - Machines ; Tools Impact factor: 1.140, year: 2015 http://www.metrology.pg.gda.pl/archives.html

  4. Vibration Control via Stiffness Switching of Magnetostrictive Transducers

    Science.gov (United States)

    Scheidler, Justin J.; Asnani, Vivake M.; Dapino, Marcelo J.

    2016-01-01

    In this paper, a computational study is presented of structural vibration control that is realized by switching a magnetostrictive transducer between high and low stiffness states. Switching is accomplished by either changing the applied magnetic field with a voltage excitation or changing the shunt impedance on the transducer's coil (i.e., the magnetostrictive material's magnetic boundary condition). Switched-stiffness vibration control is simulated using a lumped mass supported by a damper and the magnetostrictive transducer (mount), which is represented by a nonlinear, electromechanical model. Free vibration of the mass is calculated while varying the mount's stiffness according to a reference switched-stiffness vibration control law. The results reveal that switching the magnetic field produces the desired change in stiffness, but also an undesired actuation force that can significantly degrade the vibration control. Hence, a modified switched-stiffness control law that accounts for the actuation force is proposed and implemented for voltage-controlled stiffness switching. The influence of the magneto-mechanical bias condition is also discussed. Voltage-controlled stiffness switching is found to introduce damping equivalent to a viscous damping factor up to about 0.13; this is shown to primarily result from active vibration reduction caused by the actuation force. The merit of magnetostrictive switched-stiffness vibration control is then quantified by comparing the results of voltage- and shunt-controlled stiffness switching to the performance of optimal magnetostrictive shunt damping. For the cases considered, optimal resistive shunt damping performed considerably better than both voltage- and shunt-controlled stiffness switching.

  5. Finite Element Simulation of the Vibration Provided by Sandwich Rigid Panel with a Resilient Material In Between under Heavyweight Impact

    Directory of Open Access Journals (Sweden)

    Shun-Fa Hwang

    2014-01-01

    Full Text Available The purpose of the present work is to use an explicit finite element code to model the impact behavior of a heavyweight impact source like rubber ball and to predict the floor impact vibration of resilient materials, which are used in the floor coverings construction for sound insulation. To simulate the impact force of rubber balls, the hyperviscoelastic rubber model is applied. Then, this rubber model is used in the simulation for the impact vibration of resilient materials. The results indicate that the hyperviscoelastic rubber model could precisely simulate the impact force of rubber balls, as its two parameters are properly chosen according to the desired impact force. Also, the present model could capture the impact and vibration behavior of the considered materials and reasonably evaluate the insulation effect of resilient materials.

  6. A new isolator for vibration control

    Science.gov (United States)

    Behrooz, Majid; Sutrisno, Joko; Wang, Xiaojie; Fyda, Robert; Fuchs, Alan; Gordaninejad, Faramarz

    2011-03-01

    This study presents the feasibility of a new variable stiffness and damping isolator (VSDI) in an integrated vibratory system. The integrated system comprised of two VSDIs, a connecting plate and a mass. The proposed VSDI consists of a traditional steel-rubber vibration absorber, as the passive element, and a magneto-rheological elastomer (MRE), with a controllable (or variable) stiffness and damping, as the semi-active element. MREs' stiffness and damping properties can be altered by a magnetic field. Dynamic testing on this integrated system has been performed to investigate the effectiveness of the VSDIs for vibration control. Experimental results show significant shift in natural frequency, when activating the VSDIs. Transmissibility and natural frequency of the integrated system are obtained from properties of single device. The experimental and predicted results show good agreement between the values of the natural frequency of the system at both off and on states. However, system damping predictions are different from experimental results. This might be due to unforeseen effects of pre-stressed MREs and nonlinear material properties.

  7. An application of eddy current damping effect on single point diamond turning of titanium alloys

    Science.gov (United States)

    Yip, W. S.; To, S.

    2017-11-01

    Titanium alloys Ti6Al4V (TC4) have been popularly applied in many industries. They have superior material properties including an excellent strength-to-weight ratio and corrosion resistance. However, they are regarded as difficult to cut materials; serious tool wear, a high level of cutting vibration and low surface integrity are always involved in machining processes especially in ultra-precision machining (UPM). In this paper, a novel hybrid machining technology using an eddy current damping effect is firstly introduced in UPM to suppress machining vibration and improve the machining performance of titanium alloys. A magnetic field was superimposed on samples during single point diamond turning (SPDT) by exposing the samples in between two permanent magnets. When the titanium alloys were rotated within a magnetic field in the SPDT, an eddy current was generated through a stationary magnetic field inside the titanium alloys. An eddy current generated its own magnetic field with the opposite direction of the external magnetic field leading a repulsive force, compensating for the machining vibration induced by the turning process. The experimental results showed a remarkable improvement in cutting force variation, a significant reduction in adhesive tool wear and an extreme long chip formation in comparison to normal SPDT of titanium alloys, suggesting the enhancement of the machinability of titanium alloys using an eddy current damping effect. An eddy current damping effect was firstly introduced in the area of UPM to deliver the results of outstanding machining performance.

  8. The Study of Damped Harmonic Oscillations Using an Electronic Counter

    Science.gov (United States)

    Wadhwa, Ajay

    2009-01-01

    We study damped harmonic oscillations in mechanical systems like the loaded spring and simple pendulum with the help of an oscillation measuring electronic counter. The experimental data are used in a software program that solves the differential equation for damped vibrations of any system and determines its position, velocity and acceleration as…

  9. Stiffness and damping in mechanical design

    National Research Council Canada - National Science Library

    Rivin, Eugene I

    1999-01-01

    ... important conceptual issues are stiffness of mechanical structures and their components and damping in mechanical systems sensitive to and/or generating vibrations. Stiffness and strength are the most important criteria for many mechanical designs. However, although there are hundreds of books on various aspects of strength, and strength issues ar...

  10. A vibrating razor blade machining tool for material removal on low- density foams

    Energy Technology Data Exchange (ETDEWEB)

    Hillyer, D.F. Jr.

    1990-10-01

    The Lawrence Livermore National Laboratory (LLNL) has developed an accurate method of machining low-density foams into rectangular blank shapes by using a commercial oscillating razor blade machining tool concept marketed as a Vibratome. Since 1970, Vibratome has been used by medical laboratories to section fresh or fixed animal and plant tissues without freezing or embedding. By employing a vibrating razor blade principle, Vibratome sectioning avoids the alteration of morphology and the destruction of enzyme activities. The patented vibrating blade principle moves the sectioning razor blade in a reciprocating arcuate path as it penetrates the specimen. Sectioning takes place in a liquid bath using an ordinary injector-type razor blade. Although other commercial products may accomplish the same task, the Vibratome concept is currently being used at LLNL to obtain improved foam surface qualities from razor machining by combining state-of-the-art air bearing hardware with precise linear motion and an electrodynamic exciter that generates sinusoidal excitation. Razor cut foam surfaces of less than 25 {mu}m (0.001 in.) flatness are achieved over areas of 8.75 in.{sup 2} (2.5 {times} 3.5 in.). Razor machining of wide or narrow foam surfaces is generally characterized by a continuous curl chip for the full length of the material removed. This continuous chip facilitates flatness and prevents increased surface densities caused by material chip collection often left in the surface cells by conventional machine tools. This report covers the design evolution of razor machining of non-metallic soft materials. Hardware that maintains close dimensional tolerances and concurrently leaves the machined surface free of physical property changes is described. 20 figs.

  11. Balanced calibration of resonant shunt circuits for piezoelectric vibration control

    DEFF Research Database (Denmark)

    Høgsberg, Jan; Krenk, Steen

    2012-01-01

    Shunting of piezoelectric transducers and suitable electric circuits constitutes an effective passive approach to resonant vibration damping of structures. Most common design concepts for resonant resistor-inductor (RL) shunt circuits rely on either maximization of the attainable modal damping...

  12. Behavior of granite-epoxy composite beams subjected to mechanical vibrations

    Directory of Open Access Journals (Sweden)

    Antonio Piratelli-Filho

    2010-12-01

    Full Text Available The capacity to damp mechanical vibrations is one of the most important properties of granite-epoxy composites, even superior to the cast iron one. For this reason, these materials have been adopted for manufacturing of tool machine foundations and precision instruments. This work presents a study concerning the behavior of particulate composite beams, based on granite powder and epoxy, subjected to mechanical vibrations. Composite samples were prepared with different combinations of processing variables, like the weight fraction of epoxy in the mixture and size distributions of granite particles. The damping behavior of the material was investigated adopting the logarithmic decrement method. Samples, in the form of prismatic beams, were excited in the middle point and the output signal was measured in a point located at the extremity. The obtained results showed that composite samples, with weight fractions of about 80% of granite and 20% of epoxy, presented damping properties approximately three times greater than gray cast iron.

  13. Structural Damping with Friction Beams

    Directory of Open Access Journals (Sweden)

    L. Gaul

    2008-01-01

    Full Text Available In the last several years, there has been increasing interest in the use of friction joints for enhancing damping in structures. The joints themselves are responsible for the major part of the energy dissipation in assembled structures. The dissipated work in a joint depends on both the applied normal force and the excitation force. For the case of a constant amplitude excitation force, there is an optimal normal force which maximizes the damping. A ‘passive’ approach would be employed in this instance. In most cases however, the excitation force, as well as the interface parameters such as the friction coefficient, normal pressure distribution, etc., are not constant. In these cases, a ‘semi-active’ approach, which implements an active varying normal force, is necessary. For the ‘passive’ and ‘semi-active’ approaches, the normal force has to be measured. Interestingly, since the normal force in a friction joint influences the local stiffness, the natural frequencies of the assembled structure can be tuned by adjusting the normal force. Experiments and simulations are performed for a simple laboratory structure consisting of two superposed beams with friction in the interface. Numerical simulation of the friction interface requires non-linear models. The response of the double beam system is simulated using a numerical algorithm programmed in MATLAB which models point-to-point friction with the Masing friction model. Numerical predictions and measurements of the double beam free vibration response are compared. A practical application is then described, in which a friction beam is used to damp the vibrations of the work piece table on a milling machine. The increased damping of the table reduces vibration amplitudes, which in turn results in enhanced surface quality of the machined parts, reduction in machine tool wear, and potentially higher feed rates. Optimal positioning of the friction beams is based on knowledge of the mode

  14. Phenomenology of chiral damping in noncentrosymmetric magnets

    KAUST Repository

    Akosa, Collins Ashu

    2016-06-21

    A phenomenology of magnetic chiral damping is proposed in the context of magnetic materials lacking inversion symmetry. We show that the magnetic damping tensor acquires a component linear in magnetization gradient in the form of Lifshitz invariants. We propose different microscopic mechanisms that can produce such a damping in ferromagnetic metals, among which local spin pumping in the presence of an anomalous Hall effect and an effective “s-d” Dzyaloshinskii-Moriya antisymmetric exchange. The implication of this chiral damping in terms of domain-wall motion is investigated in the flow and creep regimes.

  15. Double-beam cantilever structure with embedded intelligent damping block: Dynamics and control

    Science.gov (United States)

    Szmidt, Tomasz; Pisarski, Dominik; Bajer, Czesław; Dyniewicz, Bartłomiej

    2017-08-01

    In this paper a semi-active method to control the vibrations of twin beams connected at their tips by a smart damping element is investigated. The damping element can be made of a magnetorheological elastomer or a smart material of another type, for instance vacuum packed particles. What is crucial is the ability to modify the storage and loss moduli of the damping block by means of devices attached directly to the vibrating structure. First, a simple dynamical model of the system is proposed. The continuous model is discretized using the Galerkin procedure. Then, a practical state-feedback control law is developed. The control strategy aims at achieving the best instantaneous energy dissipation of the system. Numerical simulations confirm its effectiveness in reducing free vibrations. The proposed control strategy appears to be robust in the sense that its application does not require any knowledge of the initial conditions imposed on the structure, and its performance is better than passive solutions, especially for the system induced in the first mode.

  16. Vibration of hydraulic machinery

    CERN Document Server

    Wu, Yulin; Liu, Shuhong; Dou, Hua-Shu; Qian, Zhongdong

    2013-01-01

    Vibration of Hydraulic Machinery deals with the vibration problem which has significant influence on the safety and reliable operation of hydraulic machinery. It provides new achievements and the latest developments in these areas, even in the basic areas of this subject. The present book covers the fundamentals of mechanical vibration and rotordynamics as well as their main numerical models and analysis methods for the vibration prediction. The mechanical and hydraulic excitations to the vibration are analyzed, and the pressure fluctuations induced by the unsteady turbulent flow is predicted in order to obtain the unsteady loads. This book also discusses the loads, constraint conditions and the elastic and damping characters of the mechanical system, the structure dynamic analysis, the rotor dynamic analysis and the system instability of hydraulic machines, including the illustration of monitoring system for the instability and the vibration in hydraulic units. All the problems are necessary for vibration pr...

  17. Stochastic finite element method for random harmonic analysis of composite plates with uncertain modal damping parameters

    Science.gov (United States)

    Sepahvand, K.

    2017-07-01

    Damping parameters of fiber-reinforced composite possess significant uncertainty due to the structural complexity of such materials. Considering the parameters as random variables, this paper uses the generalized polynomial chaos (gPC) expansion to capture the uncertainty in the damping and frequency response function of composite plate structures. A spectral stochastic finite element formulation for damped vibration analysis of laminate plates is employed. Experimental modal data for samples of plates is used to identify and realize the range and probability distributions of uncertain damping parameters. The constructed gPC expansions for the uncertain parameters are used as inputs to a deterministic finite element model to realize random frequency responses on a few numbers of collocation points generated in random space. The realizations then are employed to estimate the unknown deterministic functions of the gPC expansion approximating the responses. Employing modal superposition method to solve harmonic analysis problem yields an efficient sparse gPC expansion representing the responses. The results show while the responses are influenced by the damping uncertainties at the mid and high frequency ranges, the impact in low frequency modes can be safely ignored. Utilizing a few random collocation points, the method indicates also a very good agreement compared to the sampling-based Monte Carlo simulations with large number of realizations. As the deterministic finite element model serves as black-box solver, the procedure can be efficiently adopted to complex structural systems with uncertain parameters in terms of computational time.

  18. Understanding of bridge cable vibrations and the associate flow-field through the full-scale monitoring of vibrations and Wind

    DEFF Research Database (Denmark)

    Acampora, Antonio

    bridges continuously becoming longer and lighter have resulted in a high number of observations of cable vibrations. A theoretical background for the tool used in this work is presented in terms of cables vibrations mechanisms, aerodynamic damping and system identification techniques. A detailed......-scale monitoring events. Special thanks to Rune Brincker to grant permission to use the material of his newly published book about system identification to form the chapter of this thesis. A special thanks also to Anela Bajeric for granting the permission to use her material about system identification review...... vibrations. The research starts from data collection of cables vibrations of the Øresund Bridge. A dedicated monitoring system was installed to record full-scale data together with wind field measurements and meteorological data, during cables vibrations. Results from the monitoring system are reported...

  19. Active damping of the 1D rocking mode

    NARCIS (Netherlands)

    Babakhani, B.; de Vries, Theodorus J.A.

    Active damping of a rotational vibration mode in the linear guidance of a precision machine in a one dimensional (1D) setting is considered in this paper. This so-called rocking mode presents itself in machines having linear actuation. The limitation this vibration mode imposes on the machine

  20. Dampness in Buildings and Health

    DEFF Research Database (Denmark)

    Clausen, Geo; Rode, Carsten; Bornehag, Carl-Gustaf

    1999-01-01

    . The main themes are:· Continued research in human perception of indoor air quality, especially by identification of the factors that may cause annoyance to the occupants. Such annoyances may be emissions from materials or biological activity, and is often linked to the dampness of buildings.· Studies...

  1. Optimal design of a vibration-based energy harvester using magnetostrictive material (MsM)

    Science.gov (United States)

    Hu, J.; Xu, F.; Huang, A. Q.; Yuan, F. G.

    2011-01-01

    In this study, an optimal vibration-based energy harvesting system using magnetostrictive material (MsM) was designed and tested to enable the powering of a wireless sensor. In particular, the conversion efficiency, converting from magnetic to electric energy, is approximately modeled from the magnetic field induced by the beam vibration. A number of factors that affect the output power such as the number of MsM layers, coil design and load matching are analyzed and explored in the design optimization. From the measurements, the open-circuit voltage can reach 1.5 V when the MsM cantilever beam operates at the second natural frequency 324 Hz. The AC output power is 970 µW, giving a power density of 279 µW cm - 3. The attempt to use electrical reactive components (either inductors or capacitors) to resonate the system at any frequency has also been analyzed and tested experimentally. The results showed that this approach is not feasible to optimize the power. Since the MsM device has low output voltage characteristics, a full-wave quadrupler has been designed to boost the rectified output voltage. To deliver the maximum output power to the load, a complex conjugate impedance matching between the load and the MsM device is implemented using a discontinuous conduction mode (DCM) buck-boost converter. The DC output power after the voltage quadrupler reaches 705 µW and the corresponding power density is 202 µW cm - 3. The output power delivered to a lithium rechargeable battery is around 630 µW, independent of the load resistance.

  2. Power oscillation damping controller

    DEFF Research Database (Denmark)

    2012-01-01

    A power oscillation damping controller is provided for a power generation device such as a wind turbine device. The power oscillation damping controller receives an oscillation indicating signal indicative of a power oscillation in an electricity network and provides an oscillation damping control...... signal in response to the oscillation indicating signal, by processing the oscillation damping control signal in a signal processing chain. The signal processing chain includes a filter configured for passing only signals within a predetermined frequency range....

  3. Relaxation damping in oscillating contacts.

    Science.gov (United States)

    Popov, M; Popov, V L; Pohrt, R

    2015-11-09

    If a contact of two purely elastic bodies with no sliding (infinite coefficient of friction) is subjected to superimposed oscillations in the normal and tangential directions, then a specific damping appears, that is not dependent on friction or dissipation in the material. We call this effect "relaxation damping". The rate of energy dissipation due to relaxation damping is calculated in a closed analytic form for arbitrary axially-symmetric contacts. In the case of equal frequency of normal and tangential oscillations, the dissipated energy per cycle is proportional to the square of the amplitude of tangential oscillation and to the absolute value of the amplitude of normal oscillation, and is dependent on the phase shift between both oscillations. In the case of low frequency tangential oscillations with superimposed high frequency normal oscillations, the dissipation is proportional to the ratio of the frequencies. Generalization of the results for macroscopically planar, randomly rough surfaces as well as for the case of finite friction is discussed.

  4. Damping performance of cocured composite laminates with embedded viscoelastic layers

    Science.gov (United States)

    Biggerstaff, Janet M.; Kosmatka, John B.

    1998-06-01

    Cocuring viscoelastic damping materials in composites has been shown to be successful in greatly increasing the damping of composite structures. The damping performance, however, is often not as high in cocured composites as in secondarily bonded composites, where the damping material does not undergo the cure process. The reason for the discrepancy in damping between the cocured and secondarily bonded samples was found to be resin penetration into the damping material. Samples with a barrier layer between the damping material and the epoxy resin had a 15.7% to 92.3% higher loss factor (depending on the frequency) than cocured FasTapeTM 1125 samples without the barrier and at least 168% higher loss factor than cocured ISD 112 samples without the barrier. These higher damping values are very close to the values achieved by secondarily bonding. Viscoelastic damping materials typically have maximum recommended temperatures below that of the composite cure cycles. The effect of cure temperature on viscoelastic damping materials was also studied and it was determined that most damping materials are marginally affected by cure cycle temperature.

  5. EFFECT OF PARTICLE SIZE AND PACKING RATIO OF PID ON VIBRATION AMPLITUDE OF BEAM

    Directory of Open Access Journals (Sweden)

    P.S. Kachare

    2013-06-01

    Full Text Available Everything in the universe that has mass possesses stiffness and intrinsic damping. Owing to the stiffness property, mass will vibrate when excited and its intrinsic damping property will act to stop the vibration. The particle impact damper (PID is a very interesting damper that affects impact and friction effects of particles by means of energy dissipation. PID is a means for achieving high structural damping by using a particle-filled enclosure attached to a structure. The particles absorb the kinetic energy of the structure and convert it into heat through inelastic collisions between the particles themselves and between the particles and the walls of the enclosure. In this work, PID is measured for a cantilever mild steel beam with an enclosure attached to its free end; copper particles are used in this study. The PID is found to be highly nonlinear. The most useful observation is that for a very small weight penalty (about 7% to 8 %, the maximum damped amplitude of vibration at resonance with a PID, is about 9 to 10 times smaller than that without a PID. It is for more than that of with only intrinsic material damping of a majority of structural metals. A satisfactory comparison of damping with and without particles through experimentation is observed. The effect of the size of the particles on the damping performance of the beam and the effective packing ratio can be identified. It is also shown that as the packing ratio changes, the contributions of the phenomena of impact and friction towards damping also change. It is encouraging that despite its deceptive simplicity, the model captures the essential physics of PID.

  6. Preliminary Study on the Damping Effect of a Lateral Damping Buffer under a Debris Flow Load

    Directory of Open Access Journals (Sweden)

    Zheng Lu

    2017-02-01

    Full Text Available Simulating the impact of debris flows on structures and exploring the feasibility of applying energy dissipation devices or shock isolators to reduce the damage caused by debris flows can make great contribution to the design of disaster prevention structures. In this paper, we propose a new type of device, a lateral damping buffer, to reduce the vulnerability of building structures to debris flows. This lateral damping buffer has two mechanisms of damage mitigation: when debris flows impact on a building, it acts as a buffer, and when the structure vibrates due to the impact, it acts as a shock absorber, which can reduce the maximum acceleration response and subsequent vibration respectively. To study the effectiveness of such a lateral damping buffer, an impact test is conducted, which mainly involves a lateral damping buffer attached to a two-degree-of-freedom structure under a simulated debris flow load. To enable the numerical study, the equation of motion of the structure along with the lateral damping buffer is derived. A subsequent parametric study is performed to optimize the lateral damping buffer. Finally, a practical design procedure is also provided.

  7. Mode damping in a commensurate monolayer solid

    DEFF Research Database (Denmark)

    Bruch, Ludwig Walter; Hansen, Flemming Yssing

    1997-01-01

    The normal modes of a commensurate monolayer solid may be damped by mixing with elastic waves of the substrate. This was shown by Hall, Mills, and Black [Phys. Rev. B 32, 4932 (1985)], for perpendicular adsorbate vibrations in the presence of an isotropic elastic medium. That work is generalized...... anisotropy of the elastic behavior of the graphite leads to quite different wave-vector dependence of the damping for modes polarized perpendicular and parallel to the substrate. A phenomenological extension of the elasticity theory of the graphite to include bond-bending energies improves the description...

  8. Algoritmo para determinação do amortecimento de materiais cerâmicos pela técnica das freqüências naturais de vibração via excitação por impulso Algorithm to determine the damping of ceramic materials by the impulse excitation technique

    Directory of Open Access Journals (Sweden)

    A. H. A. Pereira

    2012-06-01

    Full Text Available O amortecimento ou atrito interno é uma das propriedades mais sensíveis de materiais e estruturas tanto em escala macro como microscópica e um bom indicador para a caracterização de danos estruturais, sendo particularmente sensível à presença de trincas e micro-trincas. O objetivo deste trabalho foi desenvolver um algoritmo que permitisse incorporar a caracterização do amortecimento à técnica das freqüências naturais de vibração via excitação por impulso, já bem estabelecida pela norma ASTM E1876 e amplamente empregada na determinação não-destrutiva dos módulos elásticos de materiais cerâmicos. Foi desenvolvido um algoritmo para a determinação do amortecimento fundamentado na análise de sinal no domínio de tempo-freqüência, no método do decremento logarítmico e no modelo viscoelástico equivalente. O algoritmo foi validado empregando um gerador de ondas de formato arbitrário e aplicado na caracterização de dois materiais, sendo um concreto refratário de alta alumina, com e sem dano por choque térmico, e um aço SAE 1020. O algoritmo foi eficiente ao determinar a frequência e o amortecimento de sinais arbitrários e dos corpos de prova, e em limitar a análise ao modo de vibração de interesse, minimizando assim a interferência de outros modos. O algoritmo permitiu integrar com eficiência o cálculo do amortecimento à técnica de excitação por impulso.Damping is one of the most sensitive properties of materials and structures, in macro and microscopic scale, which makes it particularly sensitive to the presence of cracks and micro-cracks and a good parameter to the characterization of structural damages. The aim of this work was to develop an algorithm to allow the incorporation of the damping characterization to the natural frequencies of vibration technique (by impulse excitation, already well established for the non-destructive determination of elastic moduli by ASTM E1876 and correlated standards

  9. Vibration and Sound Damping in Polymers

    Indian Academy of Sciences (India)

    IAS Admin

    characterization and applications of nano- multiferroics, nano- semiconductors, nano- composites, nanophosphors and nanosensors. 4Sabu Thomas is at the. Mahatma ... elastic solid obeys Hooke's Law, i.e., within the elastic limit, stress is directly .... Hence, sound travels fast in solids, but it is slow in liquids and gases.

  10. Vibration and Sound Damping in Polymers

    Indian Academy of Sciences (India)

    V G Geethamma1 R Asaletha2 Nandakumar Kalarikkal1 Sabu Thomas3. Mahatma Gandhi University, Kerala. Cochin University of Science and Technology. Director International and Inter-University Centre for Nanoscience and Nanotechnology & School of Chemical Sciences Mahatma Gandhi University Kottayam 686 ...

  11. Active damping of multiferroic composite plates using 1–3 piezoelectric composites

    Science.gov (United States)

    Kattimani, S. C.

    2017-12-01

    A layer-wise shear deformation theory is used to analyze the smart damping of multiferroic composite or magneto-electro-elastic (MEE) plates. The intent of this analysis is to investigate the need for incorporating additional smart elements for controlling the vibrations of multiferroic composite plates. Active constrained layer damping (ACLD) treatment has been incorporated to alleviate the vibration of MEE plate. A layer of viscoelastic material is used as constrained layer for the ACLD treatment. The coupled constitutive equations of multiferroic (ferroelectric and ferromagnetic) composite materials along with the total potential energy principle are used to derive the finite element formulation for the overall multiferroic or MEE plate. Maxwell’s electrostatic and electromagnetic relations are used to compute the electric and magnetic potential distribution. Influence of obliquely reinforced piezoelectric fibers in the piezoelectric layer of the ACLD treatment has also been investigated. In order to investigate the importance of using ACLD treatment for an active damping of multiferroic or MEE plate, an active control of MEE plate has also been analyzed by providing the control voltage directly to the piezoelectric layers of the MEE substrate plate without using the ACLD treatment. The present study suggests that for an optimal control of MEE plates, the smartness element such as the ACLD treatment is essentially required.

  12. VIBRATION ISOLATION SYSTEM PROBABILITY ANALYSIS

    Directory of Open Access Journals (Sweden)

    Smirnov Vladimir Alexandrovich

    2012-10-01

    Full Text Available The article deals with the probability analysis for a vibration isolation system of high-precision equipment, which is extremely sensitive to low-frequency oscillations even of submicron amplitude. The external sources of low-frequency vibrations may include the natural city background or internal low-frequency sources inside buildings (pedestrian activity, HVAC. Taking Gauss distribution into account, the author estimates the probability of the relative displacement of the isolated mass being still lower than the vibration criteria. This problem is being solved in the three dimensional space, evolved by the system parameters, including damping and natural frequency. According to this probability distribution, the chance of exceeding the vibration criteria for a vibration isolation system is evaluated. Optimal system parameters - damping and natural frequency - are being developed, thus the possibility of exceeding vibration criteria VC-E and VC-D is assumed to be less than 0.04.

  13. Study of modal coupling procedures for the shuttle: A matrix method for damping synthesis

    Science.gov (United States)

    Hasselman, T. K.

    1972-01-01

    The damping method was applied successfully to real structures as well as analytical models. It depends on the ability to determine an appropriate modal damping matrix for each substructure. In the past, modal damping matrices were assumed diagonal for lack of being able to determine the coupling terms which are significant in the general case of nonproportional damping. This problem was overcome by formulating the damped equations of motion as a linear perturbation of the undamped equations for light structural damping. Damped modes are defined as complex vectors derived from the complex frequency response vectors of each substructure and are obtained directly from sinusoidal vibration tests. The damped modes are used to compute first order approximations to the modal damping matrices. The perturbation approach avoids ever having to solve a complex eigenvalue problem.

  14. Compact Vibration Damper

    Science.gov (United States)

    Ivanco, Thomas G. (Inventor)

    2014-01-01

    A vibration damper includes a rigid base with a mass coupled thereto for linear movement thereon. Springs coupled to the mass compress in response to the linear movement along either of two opposing directions. A converter coupled to the mass converts the linear movement to a corresponding rotational movement. A rotary damper coupled to the converter damps the rotational movement.

  15. Actuator design for vibration assisted machining of high performance materials with ultrasonically modulated cutting speed

    Science.gov (United States)

    Rinck, Philipp M.; Sitzberger, Sebastian; Zaeh, Michael F.

    2017-06-01

    In vibration assisted machining, an additional high-frequency oscillation is superimposed on the kinematics of the conventional machining process. This generates oscillations on the cutting edge in the range of a few micrometers, thereby causing a high-frequency change in the cutting speed or the feed. Consequently, a reduction of cutting forces, an increase of the tool life as well as an improvement of the workpiece quality can be achieved. In milling and grinding it has been shown that these effects are already partially present in the case of a vibration excitation in axial direction relative to the workpiece, which is perpendicular to the cutting direction. Further improvements of the process results can be achieved by superimposing a vibration in cutting direction and thus modifying the cutting speed at high frequency. The presented work shows the design of an ultrasonic actuator that enables vibration-assisted milling and grinding with ultrasonically modulated cutting speed. The actuator system superimposes a longitudinal torsional ultrasonic oscillation to the milling or grinding tool. It uses a bolt clamped Langevin transducer and a helically slotted horn, which degenerates the longitudinal vibration into a combined longitudinal torsional (L-T) vibration at the output surface. A finite element analysis is used to determine the vibration resonance frequency and mode shapes to maximize the torsional output. Afterwards, the simulation has been experimentally validated.

  16. Two methods for estimating aeroelastic damping of operational wind turbine modes from experiments

    DEFF Research Database (Denmark)

    Hansen, Morten Hartvig; Thomsen, Kenneth; Fuglsang, Peter

    2006-01-01

    show that turbine vibrations related to the first two tower bending modes can be excited by blade pitch and generator torque variations. However, the excited turbine vibrations are not pure modal vibrations and the estimated damping is therefore not the actual modal damping. The second method is based......The theory and results of two experimental methods for estimating the modal damping of a wind turbine during operation are presented. Estimations of the aeroelastic damping of the operational turbine modes (including the effects of the aerodynamic forces) give a quantitative view of the stability...... characteristics of the turbine. In the first method the estimation of modal damping is based on the assumption that a turbine mode can be excited by a harmonic force at its natural frequency, whereby the decaying response after the end of excitation gives an estimate of the damping. Simulations and experiments...

  17. Ultrasonic Vibration Assisted Grinding of Bio-ceramic Materials: Modeling, Simulation, and Experimental Investigations on Edge Chipping

    Science.gov (United States)

    Tesfay, Hayelom D.

    Bio-ceramics are those engineered materials that find their applications in the field of biomedical engineering or medicine. They have been widely used in dental restorations, repairing bones, joint replacements, pacemakers, kidney dialysis machines, and respirators. etc. due to their physico-chemical properties, such as excellent corrosion resistance, good biocompatibility, high strength and high wear resistance. Because of their inherent brittleness and hardness nature they are difficult to machine to exact sizes and dimensions. Abrasive machining processes such as grinding is one of the most widely used manufacturing processes for bioceramics. However, the principal technical challenge resulted from these machining is edge chipping. Edge chipping is a common edge failure commonly observed during the machining of bio-ceramic materials. The presence of edge chipping on bio-ceramic products affects dimensional accuracy, increases manufacturing cost, hider their industrial applications and causes potential failure during service. To overcome these technological challenges, a new ultrasonic vibration-assisted grinding (UVAG) manufacturing method has been developed and employed in this research. The ultimate aim of this study is to develop a new cost-effective manufacturing process relevant to eliminate edge chippings in grinding of bio-ceramic materials. In this dissertation, comprehensive investigations will be carried out using experimental, theoretical, and numerical approaches to evaluate the effect of ultrasonic vibrations on edge chipping of bioceramics. Moreover, effects of nine input variables (static load, vibration frequency, grinding depth, spindle speed, grinding distance, tool speed, grain size, grain number, and vibration amplitude) on edge chipping will be studied based on the developed models. Following a description of previous research and existing approaches, a series of experimental tests on three bio-ceramic materials (Lava, partially fired Lava

  18. A Novel Strain Gauge with Damping Capability

    Directory of Open Access Journals (Sweden)

    Xiaohua LI

    2009-10-01

    Full Text Available The goal of this work is to investigate the properties of a new type of multifunctional composite which is based on multi-walled carbon nanotubes (MWCNT. The composite was prepared from a paper like MWCNT film which was sandwiched between two adhesive layers. Two point probe and four point probe methods were used to test its mechanical strain sensing properties. Nanoindentation and direct shear tests were used to acquire the Young’s modulus and shear modulus of MWCNT film composite. Its structural damping properties were investigated via a free vibration test. This new type of carbon nanotube based composite may potentially serve simultaneously as both a strain gauge and a damping treatment for use in structural vibration control.

  19. Adaptive synchronized switch damping on an inductor: a self-tuning switching law

    Science.gov (United States)

    Kelley, Christopher R.; Kauffman, Jeffrey L.

    2017-03-01

    Synchronized switch damping (SSD) techniques exploit low-power switching between passive circuits connected to piezoelectric material to reduce structural vibration. In the classical implementation of SSD, the piezoelectric material remains in an open circuit for the majority of the vibration cycle and switches briefly to a shunt circuit at every displacement extremum. Recent research indicates that this switch timing is only optimal for excitation exactly at resonance and points to more general optimal switch criteria based on the phase of the displacement and the system parameters. This work proposes a self-tuning approach that implements the more general optimal switch timing for synchronized switch damping on an inductor (SSDI) without needing any knowledge of the system parameters. The law involves a gradient-based search optimization that is robust to noise and uncertainties in the system. Testing of a physical implementation confirms this law successfully adapts to the frequency and parameters of the system. Overall, the adaptive SSDI controller provides better off-resonance steady-state vibration reduction than classical SSDI while matching performance at resonance.

  20. The role of whole body vibration, posture and manual materials handling as risk factors for low back pain in occupational drivers.

    Science.gov (United States)

    Okunribido, O O; Magnusson, M; Pope, M H

    2008-03-01

    It seems evident that occupational drivers have an increased risk of developing back pain. Not only are they exposed to whole body vibration (vibration), their work often includes exposure to several other risk factors for low back pain (LBP), particularly the seated posture (posture) and manual materials handling (MMH). Excessive demands on posture are likely to be aggravated by vibration and vice versa, and the risks may be further compounded when MMH is performed. This study investigated the relative role of vibration, posture and MMH as risk factors for LBP and the stated hypothesis was that the risks for LBP in drivers are the combined effect of vibration, posture and/or MMH. The findings showed that interaction effects due to posture and one or both of vibration and MMH, rather than the individual exposure effects, are the main contributors for precipitation of LBP.

  1. Low back pain in drivers: The relative role of whole-body vibration, posture and manual materials handling

    Science.gov (United States)

    Okunribido, O. O.; Magnusson, M.; Pope, M. H.

    2006-12-01

    A cross-sectional study was conducted to investigate the relative role of whole-body vibration (WBV), posture and manual materials handling (MMH) as risk factors for low back pain (LBP). Using a validated questionnaire, information about health history, posture and MMH performed was obtained from 394 workers who drove vehicles as part of their job (according to seven predefined occupational groups) and 59 who did not. The intention was to reflect a wide range of exposures with the lower end of the exposure spectrum defined as that of non-manual workers who do not drive as part of their job. Based on the questionnaire responses and direct measurements of vibration exposure, personal aggregate measures of exposure were computed for each of the respondents, i.e., total vibration dose (TVD), posture score (PS) and manual handling score (MHS). Odds ratios (and 95% confidence intervals) for back pain were obtained from logistics regression models and log-linear backward elimination analysis was performed. The findings showed that 'combined exposure' due to posture and one or both of vibration and MMH, rather than the individual exposure to one of the three factors (WBV, posture, MMH) is the main contributor of the increased prevalence of LBP.

  2. Analysis of the detection materials as resonant pads for attaching the measuring arm of the interferometer when sensing mechanical vibrations

    Science.gov (United States)

    Nedoma, Jan; Fajkus, Marcel; Martinek, Radek; Zboril, Ondrej; Bednarek, Lukas; Novak, Martin; Witas, Karel; Vasinek, Vladimir

    2017-05-01

    Fiber-optic sensors (FOS), today among the most widespread measuring sensors and during various types of measuring, are irreplaceable. Among the distinctive features include immunity to electromagnetic interference, passivity regarding power supply and high sensitivity. One of the representatives FOS is the interferometric sensors working on the principle of interference of light. Authors of this article focused on the analysis of the detection material as resonant pads for attaching the measuring arm of the interferometer when sensing mechanical vibrations (low frequencies). A typical example is the use of interferometer sensors in automobile traffic while sensing a vibration response from the roadway while passing the cars. For analysis was used sensor with Mach-Zehnder interferometer. Defined were different detection materials about different size and thickness. We analyzed the influence on the sensitivity (amplitude response) of the interferometer. Based on the results we have defined the best material for sensing mechanical vibrations. The signal was processed by applications created in LabView development environment. The results were verified by repeated testing in laboratory conditions.

  3. Viscoelastic Characterization of Long-Eared Owl Flight Feather Shaft and the Damping Ability Analysis

    Directory of Open Access Journals (Sweden)

    Jia-li Gao

    2014-01-01

    Full Text Available Flight feather shaft of long-eared owl is characterized by a three-parameter model for linear viscoelastic solids to reveal its damping ability. Uniaxial tensile tests of the long-eared owl, pigeon, and golden eagle flight feather shaft specimens were carried out based on Instron 3345 single column material testing system, respectively, and viscoelastic response of their stress and strain was described by the standard linear solid model. Parameter fitting result obtained from the tensile tests shows that there is no significant difference in instantaneous elastic modulus for the three birds’ feather shafts, but the owl shaft has the highest viscosity, implying more obvious viscoelastic performance. Dynamic mechanical property was characterized based on the tensile testing results. Loss factor (tanδ of the owl flight feather shaft was calculated to be 1.609 ± 0.238, far greater than those of the pigeon (0.896 ± 0.082 and golden eagle (1.087 ± 0.074. It is concluded that the long-eared owl flight feather has more outstanding damping ability compared to the pigeon and golden eagle flight feather shaft. Consequently, the long-eared owl flight feathers can dissipate the vibration energy more effectively during the flying process based on the principle of damping mechanism, for the purpose of vibration attenuation and structure radiated noise reduction.

  4. Damping of Mechanical Waves with Styrene/Butadiene Rubber Filled with Polystyrene Particle: Effects of Particles Size and Wave Frequency

    Directory of Open Access Journals (Sweden)

    M. Haghgo

    2007-08-01

    Full Text Available Utilizing polymeric materials for damping mechanical waves is of great importance in various fields of applications such as military camouflage, prevention of structural vibrational energy transfer, and noise attenuation. This ability originates from segmental dynamics of chain-like polymer molecules. Damping properties of styrene-butadiene rubbercontaining 10 wt% of monosize polystyrene particles with different diameters (from 80 nm to 500 μm was investigated in the frequency range of vibration, sound, and ultrasound via dynamic mechanical thermal analysis, normalsound adsorption test, and ultrasound attenuation coefficient measurement. The obtained results indicated that for different systems, containing different sizes of polystyrene particles, the area under the damping curve does not show significant change comparing to the neat SBR in the frequency range studied. However, addition of polystyrene particles, specifically nanosized particles, resulted in emergence of a secondary glass transition temperature which could be attributed to the modified dynamics of a layer of matrix molecules near the surface of PS particles. In the range of sound frequency, 0.5 to 6.3 kHz, the maximum damping was observed for the system containing polystyrene nanoparticles. However the single damping curve of neat SBR was separated into two or even three distinct curves owing to the presence of the particles. The maximum damping in the ultrasound frequency range was found for the system containing 0.5 mm polystyrene particles. This is attributed to different contributions from matrix chains dynamics and the reflection of mechanical waves from particles-matrix interface at different frequency ranges. On other words, the increase in the glass transition temperature of the elastomeric matrix phase with increasing the mechanical wave frequency causes a reduction in the contribution from matrix chains dynamics while the contribution due to diffraction from dispersed

  5. Numerical studies of shear damped composite beams using a constrained damping layer

    DEFF Research Database (Denmark)

    Kristensen, R.F.; Nielsen, Kim Lau; Mikkelsen, Lars Pilgaard

    2008-01-01

    Composite beams containing one or more damping layers are studied numerically. The work is based on a semi-analytical model using a Timoshenko beam theory and a full 2D finite element model. The material system analysed, is inspired by a train wagon suspension system used in a EUREKA project Sigma......!1841. For the material system, the study shows that the effect of the damping layer is strongly influenced by the presence of a stiff constraining layer, that enforces large shear strain amplitudes. The thickness of the damping rubber layer itself has only a minor influence on the overall damping....... In addition, a large influence of ill positioned cuts in the damping layer is observed....

  6. Advances in structural vibration control application of magneto-rheological visco-elastomer

    Directory of Open Access Journals (Sweden)

    Zuguang Ying

    2017-03-01

    Full Text Available Magneto-rheological visco-elastomer (MRVE as a new smart material developed in recent years has several significant advantages over magneto-rheological liquid. The adjustability of structural dynamics to random environmental excitations is required in vibration control. MRVE can supply considerably adjustable damping and stiffness for structures, and the adjustment of dynamic properties is achieved only by applied magnetic fields with changeless structure design. Increasing researches on MRVE dynamic properties, modeling, and vibration control application are presented. Recent advances in MRVE dynamic properties and structural vibration control application including composite structural vibration mitigation under uniform magnetic fields, vibration response characteristics improvement through harmonic parameter distribution, and optimal bounded parametric control design based on the dynamical programming principle are reviewed. Relevant main methods and results introduced are beneficial to understanding and researches on MRVE application and development.

  7. Simulating Nonlinear Oscillations of Viscoelastically Damped Mechanical Systems

    Directory of Open Access Journals (Sweden)

    M. D. Monsia

    2014-12-01

    Full Text Available The aim of this work is to propose a mathematical model in terms of an exact analytical solution that may be used in numerical simulation and prediction of oscillatory dynamics of a one-dimensional viscoelastic system experiencing large deformations response. The model is represented with the use of a mechanical oscillator consisting of an inertial body attached to a nonlinear viscoelastic spring. As a result, a second-order first-degree Painlevé equation has been obtained as a law, governing the nonlinear oscillatory dynamics of the viscoelastic system. Analytical resolution of the evolution equation predicts the existence of three solutions and hence three damping modes of free vibration well known in dynamics of viscoelastically damped oscillating systems. Following the specific values of damping strength, over-damped, critically-damped and under-damped solutions have been obtained. It is observed that the rate of decay is not only governed by the damping degree but, also by the magnitude of the stiffness nonlinearity controlling parameter. Computational simulations demonstrated that numerical solutions match analytical results very well. It is found that the developed mathematical model includes a nonlinear extension of the classical damped linear harmonic oscillator and incorporates the Lambert nonlinear oscillatory equation with well-known solutions as special case. Finally, the three damped responses of the current mathematical model devoted for representing mechanical systems undergoing large deformations and viscoelastic behavior are found to be asymptotically stable.

  8. Dimensionless Analysis of Segmented Constrained Layer Damping Treatments with Modal Strain Energy Method

    Directory of Open Access Journals (Sweden)

    Shitao Tian

    2016-01-01

    Full Text Available Constrained layer damping treatments promise to be an effective method to control vibration in flexible structures. Cutting both the constraining layer and the viscoelastic layer, which leads to segmentation, increases the damping efficiency. However, this approach is not always effective. A parametric study was carried out using modal strain energy method to explore interaction between segmentation and design parameters, including geometry parameters and material properties. A finite element model capable of handling treatments with extremely thin viscoelastic layer was developed based on interlaminar continuous shear stress theories. Using the developed method, influence of placing cuts and change in design parameters on the shear strain field inside the viscoelastic layer was analyzed, since most design parameters act on the damping efficiency through their influence on the shear strain field. Furthermore, optimal cut arrangements were obtained by adopting a genetic algorithm. Subject to a weight limitation, symmetric and asymmetric configurations were compared. It was shown that symmetric configurations always presented higher damping. Segmentation was found to be suitable for treatments with relatively thin viscoelastic layer. Provided that optimal viscoelastic layer thickness was selected, placing cuts would only be applicable to treatments with low shear strain level inside the viscoelastic layer.

  9. Vibrations of rotating machinery

    CERN Document Server

    Matsushita, Osami; Kanki, Hiroshi; Kobayashi, Masao; Keogh, Patrick

    2017-01-01

    This book opens with an explanation of the vibrations of a single degree-of-freedom (dof) system for all beginners. Subsequently, vibration analysis of multi-dof systems is explained by modal analysis. Mode synthesis modeling is then introduced for system reduction, which aids understanding in a simplified manner of how complicated rotors behave. Rotor balancing techniques are offered for rigid and flexible rotors through several examples. Consideration of gyroscopic influences on the rotordynamics is then provided and vibration evaluation of a rotor-bearing system is emphasized in terms of forward and backward whirl rotor motions through eigenvalue (natural frequency and damping ratio) analysis. In addition to these rotordynamics concerning rotating shaft vibration measured in a stationary reference frame, blade vibrations are analyzed with Coriolis forces expressed in a rotating reference frame. Other phenomena that may be assessed in stationary and rotating reference frames include stability characteristic...

  10. Dr. Dampe - Doctor Democracy

    DEFF Research Database (Denmark)

    Andreasen, John

    2009-01-01

    On Dr.phil. J.J.Dampe's fight for democracy in the first part of the 19th century in Denmark and his dramatic writings......On Dr.phil. J.J.Dampe's fight for democracy in the first part of the 19th century in Denmark and his dramatic writings...

  11. Investigation of the Effect of Material on Undamped Free Vibration of Cantilever Beams with Uniform Single Surface Crack

    Science.gov (United States)

    Mufazzal, Sameera; Muzakkir, S. M.; Zakir Jafri, Hasan

    2017-08-01

    Crack detection in structures is a critical area of research where the developments have been made out since decades. Various techniques are available for early identification and quantification of cracks to predict and prevent the unexpected sudden failure of structure and ensure uninterrupted service. Use of vibration analysis for detecting crack is one of the widely used techniques which offer lots of advantages over other like it is easier and less costly method and can be used for inaccessible components. The present work attempts to use modal analysis through FEA to investigate the effect of crack on natural frequency of vibration in beams of different materials, for three different crack location. From the result, it has been inferred that among Structural Steel (SS), Aluminium alloy (Al) and Gray Cast Iron (CI), the natural frequency is highest for Al beam and lowest for CI beam. Introduction of crack reduces the natural frequency of vibration, however, the effect of crack location on frequency is not uniform for different modes. Also, the trend is similar in beams of all the materials.

  12. Free vibration analysis of a rotary smart two directional functionally graded piezoelectric material in axial symmetry circular nanoplate

    Science.gov (United States)

    Mahinzare, Mohammad; Ranjbarpur, Hosein; Ghadiri, Majid

    2018-02-01

    In this article, free vibration of a rotating circular nanoplate made of two directional functionally graded piezo materials (two directional FGPM) is modeled based on the first shear deformation theory (FSDT). Based on the power-law model, electro-elastic properties of two directional FGP rotating circular nanoplates are supposed to change continuously along the thickness and radius. Employing the modified couple stress theory, the small size effect of the equations of the plate is considered. The governing equations of the first shear deformation theory (FSDT) for the studied plate are obtained based on Hamilton's principle; these equations are solved using differential quadrature method (DQM). It is shown that the vibration behavior of the plate is significantly affected by angular velocity, external electric voltage, size dependency and power-law index (thickness and radial directions).

  13. Thermal, vibrational spectra and photoluminescence properties of the nonlinear optical material MnTeMoO6

    Science.gov (United States)

    Jin, Chengguo; Shao, Juxiang; Li, Zhen; Yang, Junsheng; Cao, Qilong; Huang, Duohui; Wan, Mingjie; Wang, Fanhou

    2015-04-01

    MnTeMoO6 is a novel nonlinear optical material in near-mid-IR region. Vibrational spectra characterization, thermal and photoluminescent properties of polycrystalline MnTeMoO6 have been investigated in this work. The results show that polycrystalline MnTeMoO6 has a relatively high melting point at 725.2 °C and exhibits superheating of crystal. The observed Raman and IR bands of MnTeMoO6 are assigned to vibrations of the Mn-O bonds, MoO4 tetrahedra, and TeO4 polyhedra. Photoluminescence measurements show that MnTeMoO6 displays a strong emission peak at 467 nm under excitation at 280 nm, and the absorption band at 0.47-0.52 μm in UV-vis spectra may be caused by photoluminescence.

  14. Finite element parametric study of the influence of friction pad material and morphological characteristics on disc brake vibration phenomena

    Science.gov (United States)

    Forte, P.; Frendo, F.; Rodrigues, R. N.

    2016-09-01

    Since nowadays the NVH performance of vehicles has become an important priority, the noise radiating from brakes is considered a source of considerable passenger discomfort and dissatisfaction. Creep groan and squeal that show up with annoying vibrations and noise in specific frequency ranges are typical examples of self-excited brake vibrations caused by the stick-slip effect, the former, by the mode coupling of brake disc and friction pads or calliper, the latter. In both cases, the friction coefficient, which depends, among other factors, on the morphology of the mating surfaces and on the operating conditions, is a fundamental parameter but not the only one for the occurrence of the vibratory phenomena. Finite element complex eigenvalue parametric analyses were performed on a disc brake assembly to evaluate propensity to dynamic instability of brakes with multiple pads, as in railway brakes, as a function of the number of pads, pad shape and size, and material parameters.

  15. Effect of particulate tougheners on the damping of composite laminates

    Science.gov (United States)

    Biggerstaff, Janet M.; Kosmatka, John B.

    2000-04-01

    Rubber is commonly added to composites to increase the toughness. This research investigates adding toughening particles to graphite/epoxy composites for the purpose of increasing the vibrational damping. Adding toughening particles to the interlaminar regions of graphite/epoxy is shown to significantly increase the loss factor, although the increase is much less than can be achieved by embedding a viscoelastic damping layer. The bending stiffness and shear modulus, however, are much higher for the samples with embedded particles than samples with a viscoelastic layer. The addition of damping particles could therefore be used for stiffness-critical parts.

  16. Comparing Sources of Damping of Cross-Wind Motion

    DEFF Research Database (Denmark)

    Tarp-Johansen, Niels Jacob; Mørch, Christian; Andersen, Lars

    2009-01-01

    Cross-wind vibrations due to wave loading misaligned with the wind causes fatigue known to be design driving for support structures of large turbines offshore increasing fatigue loads notably compared to the along-wind fatigue. The small amount of damping assumed for cross-wind motion in current...... practise plays a key role in this. The questions are: does more damping exist and is one of the sources of damping the main contributor allowing for site-independent guidelines. The aim of this paper is to address these issues. It is demonstrated that tower dampers are important in order to tackle...

  17. An Alternative Corrosion Resistance Test Method for Solar Cells and Interconnection Materials Limiting the Number of Long-lasting and Expensive Damp-Heat Climate Chamber Tests

    Energy Technology Data Exchange (ETDEWEB)

    Van Aken, B.B.; Gouwen, R.J.; Veldman, D.; Bende, E.E.; Eerenstein, W. [ECN Solar Energy, Petten (Netherlands)

    2013-06-15

    Damp-heat testing of PV modules is a time-consuming process, taking months. We present an alternative test method: electrochemical noise (EcN) measurements. Data acquisition times vary between minutes for direct exposure to several tens of hours for encapsulated samples. EcN measurements are presented for several solar cell concepts and different environments. We have found that the degradation in damp-heat testing is proportional to the electrochemical noise signal. In conclusion, the electrochemical noise measurements are a fast, versatile tool to test the corrosion resistance of solar cells, which can be tested for different environments including encapsulation.

  18. Measurement of Young’s Modulus and Internal Damping of Pork Muscle in Dynamic Mode

    Science.gov (United States)

    Chakroun, Moez; Ghozlen, Med Hédi Ben

    2016-09-01

    Automotive shocks involve various tiers’ speed for different human body tissues. Knowing the behavior of these tissues, including muscles, in different vibration frequency is therefore necessary. The muscle has viscoelatic properties. Dynamically, this material has variable mechanical properties depending on the vibration frequency. A novel technique is being employed to examine the variation of the mechanical impedance of pork muscle as a function of frequency. A force is imposed on the lower surface of the sample and acceleration is measured on its upper surface. These two parameters are measured using sensors. The sample is modeled by Kelvin-Voigt model. These measures allow deducing the change in the mechanical impedance modulus (/Zexp/ = /Force: Acceleration/) of pork muscle as a function of vibration frequency. The measured impedance has a resonance of approximately 60Hz. Best-fit parameters of theoretical impedance can be deduced by superposition with the experiment result. The variation of Young’s modulus and internal damping of pig’s muscle as a function of frequency are determined. The results obtained between 5Hz and 30Hz are the same as determined by Aimedieu and al in 2003, therefore validating our technique. The Young’s modulus of muscle increases with the frequency, on the other hand, we note a rating decrease of internal damping.

  19. Research on Free Vibration Frequency Characteristics of Rotating Functionally Graded Material Truncated Conical Shells with Eccentric Functionally Graded Material Stringer and Ring Stiffeners

    Directory of Open Access Journals (Sweden)

    Dao Van Dung

    Full Text Available Abstract In this research work, an exact analytical solution for frequency characteristics of the free vibration of rotating functionally graded material (FGM truncated conical shells reinforced by eccentric FGM stringers and rings has been investigated by the displacement function method. Material properties of shell and stiffeners are assumed to be graded in the thickness direction according to a simple power law distribution. The change of spacing between stringers is considered. Using the Donnell shell theory, Leckhnisky smeared stiffeners technique and taking into account the influences of centrifugal force and Coriolis acceleration the governing equations are derived. For stiffened FGM conical shells, it is difficult that free vibration equations are a couple set of three variable coefficient partial differential equations. By suitable transformations and applying Galerkin method, this difficulty is overcome in the paper. The sixth order polynomial equation for w is obtained and it is used to analyze the frequency characteristics of rotating ES-FGM conical shells. Effects of stiffener, geometrics parameters, cone angle, vibration modes and rotating speed on frequency characteristics of the shell forward and backward wave are discussed in detail. The present approach proves to be reliable and accurate by comparing with published results available in the literature.

  20. Investigations on Void Formation in Composite Molding Processes and Structural Damping in Fiber-Reinforced Composites with Nanoscale Reinforcements

    Science.gov (United States)

    DeValve, Caleb Joshua

    Fiber-reinforced composites (FRCs) offer a stronger and lighter weight alternative to traditional materials used in engineering components such as wind turbine blades and rotorcraft structures. Composites for these applications are often fabricated using liquid molding techniques, such as injection molding or resin transfer molding. One significant issue during these processing methods is void formation due to incomplete wet-out of the resin within the fiber preform, resulting in discontinuous material properties and localized failure zones in the material. A fundamental understanding of the resin evolution during processing is essential to designing processing conditions for void-free filling, which is the first objective of the dissertation. Secondly, FRCs used in rotorcraft experience severe vibrational loads during service, and improved damping characteristics of the composite structure are desirable. To this end, a second goal is to explore the use of matrix-embedded nanoscale reinforcements to augment the inherent damping capabilities in FRCs. The first objective is addressed through a computational modeling and simulation of the infiltrating dual-scale resin flow through the micro-architectures of woven fibrous preforms, accounting for the capillary effects within the fiber bundles. An analytical model is developed for the longitudinal permeability of flow through fibrous bundles and applied to simulations which provide detailed predictions of local air entrapment locations as the resin permeates the preform. Generalized design plots are presented for predicting the void content and processing time in terms of the Capillary and Reynolds Numbers governing the molding process. The second portion of the research investigates the damping enhancement provided to FRCs in static and rotational configurations by different types and weight fractions of matrix-embedded carbon nanotubes (CNTs) in high fiber volume fraction composites. The damping is measured using

  1. Granular Media-Based Tunable Passive Vibration Suppressor

    Science.gov (United States)

    Dillon, Robert P.; Davis, Gregory L.; Shapiro, Andrew A.; Borgonia, John Paul C.; Kahn, Daniel L.; Boechler, Nicholas; Boechler,, Chiara

    2013-01-01

    and vibration suppression device is composed of statically compressed chains of spherical particles. The device superimposes a combination of dissipative damping and dispersive effects. The dissipative damping resulting from the elastic wave attenuation properties of the bulk material selected for the granular media is independent of particle geometry and periodicity, and can be accordingly designed based on the dissipative (or viscoelastic) properties of the material. For instance, a viscoelastic polymer might be selected where broadband damping is desired. In contrast, the dispersive effects result from the periodic arrangement and geometry of particles composing a linear granular chain. A uniform (monatomic) chain of statically compressed spherical particles will have a low-pass filter effect, with a cutoff frequency tunable as a function of particle mass, elastic modulus, Poisson fs ratio, radius, and static compression. Elastic waves with frequency content above this cutoff frequency will exhibit an exponential decay in amplitude as a function of propagation distance. System design targeting a specific application is conducted using a combination of theoretical, computational, and experimental techniques to appropriately select the particle radii, material (and thus elastic modulus and Poisson fs ratio), and static compression to satisfy estimated requirements derived for shock and/or vibration protection needs under particular operational conditions. The selection of a chain of polymer spheres with an elastic modulus .3 provided the appropriate dispersive filtering effect for that exercise; however, different operational scenarios may require the use of other polymers, metals, ceramics, or a combination thereof, configured as an array of spherical particles. The device is a linear array of spherical particles compressed in a container with a mechanism for attachment to the shock and/or vibration source, and a mechanism for attachment to the article requiring

  2. OPTIMAL AUTOMOBILE MUFFLER VIBRATION AND NOISE ANALYSIS

    Directory of Open Access Journals (Sweden)

    Sujit Kumar Jha

    2013-06-01

    Full Text Available The muffler is the main part of the Automobile Exhaust System, consisting of fibrous and porous materials to absorb noise and vibrations. The exhaust gas mass coming from the engine can produce resonance, which may be the source of fatigue failure in the exhaust pipe due to the presence of continuous resonance. The modes on the muffler should be located away from the engine’s operating frequencies in order to minimise the resonance. The objective of this paper is to determine the frequencies that appear at the modes, which have the more adverse effect during the operation of the automobile. An impact test has been conducted by applying the force using a hard head hammer, and data generated have been used for plotting a graph of the transfer functions using MATLAB. Six points have been selected, namely 1, 2, 3, 4, 7, and 11 on the muffler for the impact test. The collected data from theses six points have been analysed for the addition of damping. Results suggests that increasing the mass increases the damping and lowers the modes of the transfer function. Further research will identify higher strength materials that can withstand the higher gas temperatures as well as the corrosion and erosion by the gas emitted from the engine. muffler, noise, vibration,modal analysis,

  3. Suboptimal Rayleigh damping coefficients in seismic analysis of viscously-damped structures

    Science.gov (United States)

    Pan, Danguang; Chen, Genda; Wang, Zuocai

    2014-12-01

    An optimization method for the consistent evaluation of two Rayleigh damping coefficients is proposed. By minimizing an objective function such as an error term of the peak displacement of a structure, the two coefficients can be determined with response spectral analysis. The optimization method degenerates into the conventional method used in current practices when only two modes of vibration are included in the objective function. Therefore, the proposed method with all significant modes included for simplicity in practical applications results in suboptimal damping coefficients. The effects of both spatial distribution and frequency content of excitations as well as structural dynamic characteristics on the evaluation of Rayleigh damping coefficients were investigated with a five-story building structure. Two application examples with a 62-story high-rise building and a 840 m long cable-stayed bridge under ten earthquake excitations demonstrated the accuracy and effectiveness of the proposed method to account for all of the above effects.

  4. Eddy damping effect of additional conductors in superconducting levitation systems

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Zhao-Fei; Gou, Xiao-Fan, E-mail: xfgou@hhu.edu.cn

    2015-12-15

    Highlights: • In this article, for the eddy current damper attached to the HTSC, we • quantitatively investigated the damping coefficient c, damping ratio, Joule heating of the copper damper, and the vibration frequency of the PM as well. • presented four different arrangements of the copper damper, and comparatively studied their damping effects and Joule heating, and finally proposed the most advisable arrangement. - Abstract: Passive superconducting levitation systems consisting of a high temperature superconductor (HTSC) and a permanent magnet (PM) have demonstrated several fascinating applications such as the maglev system, flywheel energy storage. Generally, for the HTSC–PM levitation system, the HTSC with higher critical current density J{sub c} can obtain larger magnetic force to make the PM levitate over the HTSC (or suspended below the HTSC), however, the process of the vibration of the levitated PM, provides very limited inherent damping (essentially hysteresis). To improve the dynamic stability of the levitated PM, eddy damping of additional conductors can be considered as the most simple and effective approach. In this article, for the HTSC–PM levitation system with an additional copper damper attached to the HTSC, we numerically and comprehensively investigated the damping coefficient c, damping ratio, Joule heating of the copper damper, and the vibration frequency of the PM as well. Furthermore, we comparatively studied four different arrangements of the copper damper, on the comprehensive analyzed the damping effect, efficiency (defined by c/V{sub Cu}, in which V{sub Cu} is the volume of the damper) and Joule heating, and finally presented the most advisable arrangement.

  5. Roll Damping By Rudder Control

    DEFF Research Database (Denmark)

    Stoustrup, Jakob; Niemann, H.H.; Blanke, M.

    1994-01-01

    Roll damping and simultaneous course steering by rudder control is a challenging problem where a key factor is roll damping performance in waves.......Roll damping and simultaneous course steering by rudder control is a challenging problem where a key factor is roll damping performance in waves....

  6. Effect of viscous damping on the response of a finite beam resting ...

    African Journals Online (AJOL)

    In this work we present results for the influence of viscous damping on the response if a finite beam resting on a Pasternak foundation using Galerkin weighted residual method. Results obtained show that the vibration amplitude reduces with increase in the damping term. JONAMP Vol. 11 2007: pp. 375-378 ...

  7. Damping Proceedings Held in Las Vegas, Nevada on 5-7 March 1986. Volume 1

    Science.gov (United States)

    1986-05-01

    Vibrations by Means of Viscoelastic Laminate," Section III of Structural Damping, ASME, pp. 49-88, 1959. 14. H. Oberst and K. Frankenfeld, " Uber die Dampfung...Vibrations by Means of Viscoelastic Laminate," Section III of Structural Damping, ASME, pp. 49-88, 1959. 14. H. Oberst and K. Frankenfeld, " Uber die...extreme care and payment of full attention to specimen dimensions. For example, the resonance techniques2 (3) are shown to be useful from 100 to 1000

  8. Vibration fatigue using modal decomposition

    Science.gov (United States)

    Mršnik, Matjaž; Slavič, Janko; Boltežar, Miha

    2018-01-01

    Vibration-fatigue analysis deals with the material fatigue of flexible structures operating close to natural frequencies. Based on the uniaxial stress response, calculated in the frequency domain, the high-cycle fatigue model using the S-N curve material data and the Palmgren-Miner hypothesis of damage accumulation is applied. The multiaxial criterion is used to obtain the equivalent uniaxial stress response followed by the spectral moment approach to the cycle-amplitude probability density estimation. The vibration-fatigue analysis relates the fatigue analysis in the frequency domain to the structural dynamics. However, once the stress response within a node is obtained, the physical model of the structure dictating that response is discarded and does not propagate through the fatigue-analysis procedure. The structural model can be used to evaluate how specific dynamic properties (e.g., damping, modal shapes) affect the damage intensity. A new approach based on modal decomposition is presented in this research that directly links the fatigue-damage intensity with the dynamic properties of the system. It thus offers a valuable insight into how different modes of vibration contribute to the total damage to the material. A numerical study was performed showing good agreement between results obtained using the newly presented approach with those obtained using the classical method, especially with regards to the distribution of damage intensity and critical point location. The presented approach also offers orders of magnitude faster calculation in comparison with the conventional procedure. Furthermore, it can be applied in a straightforward way to strain experimental modal analysis results, taking advantage of experimentally measured strains.

  9. Do Lumped-Parameter Models Provide the Correct Geometrical Damping?

    DEFF Research Database (Denmark)

    Andersen, Lars

    response during excitation and the geometrical damping related to free vibrations of a hexagonal footing. The optimal order of a lumped-parameter model is determined for each degree of freedom, i.e. horizontal and vertical translation as well as torsion and rocking. In particular, the necessity of coupling...

  10. Electron-Vibration Coupling in Molecular Materials: Assignment of Vibronic Modes from Photoelectron Momentum Mapping.

    Science.gov (United States)

    Graus, M; Grimm, M; Metzger, C; Dauth, M; Tusche, C; Kirschner, J; Kümmel, S; Schöll, A; Reinert, F

    2016-04-08

    Electron-phonon coupling is one of the most fundamental effects in condensed matter physics. We here demonstrate that photoelectron momentum mapping can reveal and visualize the coupling between specific vibrational modes and electronic excitations. When imaging molecular orbitals with high energy resolution, the intensity patterns of photoelectrons of the vibronic sidebands of molecular states show characteristic changes due to the distortion of the molecular frame in the vibronically excited state. By comparison to simulations, an assignment of specific vibronic modes is possible, thus providing unique information on the coupling between electronic and vibronic excitation.

  11. Wind turbine blade with viscoelastic damping

    Science.gov (United States)

    Sievers, Ryan A.; Mullings, Justin L.

    2017-01-10

    A wind turbine blade (60) damped by viscoelastic material (54, 54A-F) sandwiched between stiffer load-bearing sublayers (52A, 52B, 56A, 56B) in portions of the blade effective to damp oscillations (38) of the blade. The viscoelastic material may be located in one or more of: a forward portion (54A) of the shell, an aft portion (54D) of the shell, pressure and suction side end caps (54B) of an internal spar, internal webbing walls (54C, 54E), and a trailing edge core (54F).

  12. System Reduction and Damping of Flexible Structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Riess; Krenk, Steen

    2007-01-01

    An increasing number of flexible structures such as cable-stayed bridges, pedestrian bridges and high-rise buildings are fitted with local dampers to mitigate vibration problems. In principle the effect of local dampers can be analyzed by use of complex modes, e.g. in conjunction with an averaging...... technique for local linearization of the damper characteristics. However, the complex mode shapes and frequencies depend on the magnitude of the damper and therefore are less suitable for design of the damper system. An efficient alternative consists in the use of a two-component representation...... of the damped modes of the structure. The idea is to represent the damped mode as a linear combination of the modes that occur in two distinctly different situations representing extreme conditions: the mode shape of the structure without the damper(s), and the mode shape of the structure, when the damper...

  13. Research and Analysis of Quasi-Zero-Stiffness Isolator with Geometric Nonlinear Damping

    Directory of Open Access Journals (Sweden)

    Qingguo Meng

    2017-01-01

    Full Text Available This paper presents a novel quasi-zero-stiffness (QZS isolator designed by combining a tension spring with a vertical linear spring. In order to improve the performance of low-frequency vibration isolation, geometric nonlinear damping is proposed and applied to a quasi-zero-stiffness (QZS vibration isolator. Through the study of static characteristics first, the relationship between force displacement and stiffness displacement of the vibration isolation mechanism is established; it is concluded that the parameters of the mechanism have the characteristics of quasi-zero stiffness at the equilibrium position. The solutions of the QZS system are obtained based on the harmonic balance method (HBM. Then, the force transmissibility of the QZS vibration isolator is analyzed. And the results indicate that increasing the nonlinear damping can effectively suppress the transmissibility compared with the nonlinear damping system. Finally, this system is innovative for low-frequency vibration isolation of rehabilitation robots and other applications.

  14. Quenching of self-excited vibrations

    NARCIS (Netherlands)

    Verhulst, F.

    2005-01-01

    Stable normal-mode vibrations in engineering can be undesirable and one of the possibilities for quenching these is by embedding the oscillator in an autoparametric system by coupling to a damped oscillator. There exists the possibility of destabilizing the undesirable vibrations by a suitable

  15. Researches Regarding the Effect of Nitinol Vibration Damper Applied to Infrastructures

    Directory of Open Access Journals (Sweden)

    Daniel Amariei

    2009-10-01

    Full Text Available Many of the performed researches all around the world aim to develop advanced technologies in order to enhance the performances of the infrastructure systems, different from the actual ones, fact which involves multidisciplinary research (IT, sensoring, electronics, smart materials and others, aiming to assist engineers in realizing full benefits of structural health monitoring. The paper presents a preliminary feasibility study of a system that can be used for damping of structural vibrations. Thus, shape memory alloys (SMA components can affect through two mechanisms the structure’s vibrations. The stresses from a SMA element that realize phase transformations, as a result of vibrations, have an effect on the frequency-amplitude characteristics. In addition, a dissipation of energy due to hysteresis in a SMA element can reduce the natural frequency and affect forced vibrations.

  16. Experimental and Theoretical Analysis for a Fluid-Loaded, Simply Supported Plate Covered by a Damping and Decoupling Composite Acoustic Coating

    Directory of Open Access Journals (Sweden)

    Baihua Yuan

    2017-01-01

    Full Text Available This work presents a vibroacoustic response model for a fluid-loaded, simply supported rectangular plate covered by a composite acoustic coating consisting of damping and decoupling layers. The model treated the damping layer and base plate as a unified whole under pure bending moments and the decoupling layer as a three-dimensional, isotropic, linear elastic solid. The validity of the model was verified by both numerical analysis and experiments and was shown to accurately extend previous studies that were limited to a plate covered by a single damping or decoupling layer with an evaluation confined solely to numerical analysis. The trends of the numerical and experimental results are generally consistent, with some differences due to the influences of water pressure and the frequency dependence of the material parameters, which are not taken into account by the numerical analysis. Both experimental and numerical results consistently show that the radiated noise reduction effect of the composite coating is superior to that of single-type coatings, which is attributed to the fact that the composite coating combines the merits of both the high vibration suppression performance of the damping layer and the superior vibration isolation performance of the decoupling layer.

  17. Evaluation of Nanomaterial Approaches to Damping in Epoxy Resin and Carbon Fiber/Epoxy Composite Structures by Dynamic Mechanical Analysis

    Science.gov (United States)

    Miller, G.; Heimann, Paula J.; Scheiman, Daniel A.; Duffy, Kirsten P.; Johnston, J. Chris; Roberts, Gary D.

    2013-01-01

    Vibration mitigation in composite structures has been demonstrated through widely varying methods which include both active and passive damping. Recently, nanomaterials have been investigated as a viable approach to composite vibration damping due to the large surface available to generate energy dissipation through friction. This work evaluates the influence of dispersed nanoparticles on the damping ratio of an epoxy matrix. Limited benefit was observed through dispersion methods, however nanoparticle application as a coating resulting in up to a three-fold increase in damping.

  18. Mechanical-plowing-based high-speed patterning on hard material via advanced-control and ultrasonic probe vibration

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhihua; Zou, Qingze, E-mail: qzzou@rci.rutgers.edu [Mechanical and Aerospace Engineering Department, Rutgers, the State University of New Jersey, Piscataway, New Jersey 08854 (United States); Tan, Jun; Jiang, Wei [Electrical and Computer Engineering Department, Rutgers, the State University of New Jersey, Piscataway, New Jersey 08854 (United States)

    2013-11-15

    In this paper, we present a high-speed direct pattern fabrication on hard materials (e.g., a tungsten-coated quartz substrate) via mechanical plowing. Compared to other probe-based nanolithography techniques based on chemical- and/or physical-reactions (e.g., the Dip-pen technique), mechanical plowing is meritorious for its low cost, ease of process control, and capability of working with a wide variety of materials beyond conductive and/or soft materials. However, direct patterning on hard material faces two daunting challenges. First, the patterning throughput is ultimately hindered by the “writing” (plowing) speed, which, in turn, is limited by the adverse effects that can be excited/induced during high-speed, and/or large-range plowing, including the vibrational dynamics of the actuation system (the piezoelectric actuator, the cantilever, and the mechanical fixture connecting the cantilever to the actuator), the dynamic cross-axis coupling between different axes of motion, and the hysteresis and the drift effects related to the piezoelectric actuators. Secondly, it is very challenging to directly pattern on ultra-hard materials via plowing. Even with a diamond probe, the line depth of the pattern via continuous plowing on ultra-hard materials such as tungsten, is still rather small (<0.5 nm), particularly when the “writing” speed becomes high. To overcome these two challenges, we propose to utilize a novel iterative learning control technique to achieve precision tracking of the desired pattern during high-speed, large-range plowing, and introduce ultrasonic vibration of the probe in the normal (vertical) direction during the plowing process to enable direct patterning on ultra hard materials. The proposed approach was implemented to directly fabricate patterns on a mask with tungsten coating and quartz substrate. The experimental results demonstrated that a large-size pattern of four grooves (20 μm in length with 300 nm spacing between lines) can be

  19. Magnetic Circuit Analyses and Turning Chatter Suppression Based on a Squeeze-Mode Magnetorheological Damping Turning Tool

    Directory of Open Access Journals (Sweden)

    Yongliang Zhang

    2015-01-01

    Full Text Available As a smart material, magnetorheological fluid (MRF has been utilized in fields including civil engineering and automotive engineering, and so on. In this study, the MR damping turning tool based on the squeeze-mode was developed to improve the vibration resistance of the tool system on the lathe. The 3D magnetic circuit simulations of the damper were performed. The influences of damper structural parameters, such as coil positions, plate thicknesses, and others, on the magnetic induction strength were investigated. Orthogonal experiments were carried out and the optimal combination of damper parameters was determined. The chatter suppressive experiments were carried out to evaluate the performance of the MR damping turning tool.

  20. Nonlinear damping and quasi-linear modelling.

    Science.gov (United States)

    Elliott, S J; Ghandchi Tehrani, M; Langley, R S

    2015-09-28

    The mechanism of energy dissipation in mechanical systems is often nonlinear. Even though there may be other forms of nonlinearity in the dynamics, nonlinear damping is the dominant source of nonlinearity in a number of practical systems. The analysis of such systems is simplified by the fact that they show no jump or bifurcation behaviour, and indeed can often be well represented by an equivalent linear system, whose damping parameters depend on the form and amplitude of the excitation, in a 'quasi-linear' model. The diverse sources of nonlinear damping are first reviewed in this paper, before some example systems are analysed, initially for sinusoidal and then for random excitation. For simplicity, it is assumed that the system is stable and that the nonlinear damping force depends on the nth power of the velocity. For sinusoidal excitation, it is shown that the response is often also almost sinusoidal, and methods for calculating the amplitude are described based on the harmonic balance method, which is closely related to the describing function method used in control engineering. For random excitation, several methods of analysis are shown to be equivalent. In general, iterative methods need to be used to calculate the equivalent linear damper, since its value depends on the system's response, which itself depends on the value of the equivalent linear damper. The power dissipation of the equivalent linear damper, for both sinusoidal and random cases, matches that dissipated by the nonlinear damper, providing both a firm theoretical basis for this modelling approach and clear physical insight. Finally, practical examples of nonlinear damping are discussed: in microspeakers, vibration isolation, energy harvesting and the mechanical response of the cochlea. © 2015 The Author(s).

  1. Vibration of imperfect rotating disk

    Directory of Open Access Journals (Sweden)

    Půst L.

    2011-12-01

    Full Text Available This study is concerned with the theoretical and numerical calculations of the flexural vibrations of a bladed disk. The main focus of this study is to elaborate the basic background for diagnostic and identification methods for ascertaining the main properties of the real structure or an experimental model of turbine disks. The reduction of undesirable vibrations of blades is proposed by using damping heads, which on the experimental model of turbine disk are applied only on a limited number of blades. This partial setting of damping heads introduces imperfection in mass, stiffness and damping distribution on the periphery and leads to more complicated dynamic properties than those of a perfect disk. Calculation of FEM model and analytic—numerical solution of disk behaviour in the limited (two modes frequency range shows the splitting of resonance with an increasing speed of disk rotation. The spectrum of resonance is twice denser than that of a perfect disk.

  2. Nontrivial effects of high-frequency excitation for strongly damped mechanical systems

    DEFF Research Database (Denmark)

    Fidlin, Alexander; Thomsen, Jon Juel

    substantially with the level of damping. For example, a strongly damped pendulum, with a hinge vibrated at high frequency along an elliptical path with horizontal or vertical axis, will line up along a line offset from the vertical; the offset vanishes for very light or very strong damping, attaining a maximum...... on a slightly modified averaging technique, and includes an elementary example of an elliptically excited pendulum for illustration, alongside with a generalization to a broader class of strongly damped dynamical systems with HF excitation. As an application example, the nontrivial behavior of a classical...

  3. Nontrivial effects of high-frequency excitation for strongly damped mechanical systems

    DEFF Research Database (Denmark)

    Fidlin, Alexander; Thomsen, Jon Juel

    2008-01-01

    substantially with the level of damping. For example, a strongly damped pendulum, with a hinge vibrated at high frequency along an elliptical path with horizontal or vertical axis, will line up along a line offset from the vertical; the offset vanishes for very light or very strong damping, attaining a maximum...... modified averaging technique, and includes an elementary example of an elliptically excited pendulum for illustration, alongside with a generalization to a broader class of strongly damped dynamical systems with HF excitation. As an application example, the nontrivial behavior of a classical optimally...

  4. Hysteresis damping characteristics calculation in an overcritically compressed member with variable cross section

    Directory of Open Access Journals (Sweden)

    Smirnov Vladimir Aleksandrovich

    Full Text Available The article focuses on calculating the loss factor in the stiffness corrector of quasi-zero stiffness vibration isolator, designed for precision equipment vibration isolation from low-frequency base vibrations. Stiffness corrector is a beam with a variable cross-section and an initial curvature loaded in the middle with the transverse load. The initial curvature of the beam is determined by solving the problem of the axial deformation of the beam of variable cross-section with an axial load exceeding the critical Euler force. The loss factor of the stiffness corrector’s material is determined in accordance with Panovko energy theory. For these purposes, the elastic shape of the stiffness corrector loaded with transverse force is calculated and potential energy of the corrector, which corresponds to the prescribed elastic shape, is obtained. Loss factor is calculated by dividing the absorption coefficient of the stiffness corrector material by its potential energy for various types of cross-sections of corrector’s beams. Determination of stiffness corrector’s material loss factor is performed through several experimental investigations, in which the coefficients of the approximating function are obtained via approximation of specimen of damped oscillations.

  5. Effects of Varied Shear Correction on the Thermal Vibration of Functionally-Graded Material Shells in an Unsteady Supersonic Flow

    Directory of Open Access Journals (Sweden)

    Chih Chiang Hong

    2017-03-01

    Full Text Available A model is presented for functionally-graded material (FGM, thick, circular cylindrical shells under an unsteady supersonic flow, following first-order shear deformation theory (FSDT with varied shear correction coefficients. Some interesting vibration results of the dynamics are calculated by using the generalized differential quadrature (GDQ method. The varied shear correction coefficients are usually functions of FGM total thickness, power law index, and environment temperature. Two parametric effects of the environmental temperature and FGM power law index on the thermal stress and center deflection are also presented. The novelty of the paper is that the maximum flutter value of the center deflection amplitude can be predicted and occurs at a high frequency of applied heat flux for a supersonic air flow.

  6. Structural dynamic modification using additive damping

    Indian Academy of Sciences (India)

    In order to control dynamic response in structures and machines, modofications using additive viscoelastic damping materials are highlighted. The techniques described for analysis include analytical methods for structural elements, FEM and perturbation methods for reanalysis or structural dynamic modifications for ...

  7. Damping mechanisms and models in structural dynamics

    DEFF Research Database (Denmark)

    Krenk, Steen

    2002-01-01

    Several aspects of damping models for dynamic analysis of structures are investigated. First the causality condition for structural response is used to identify rules for the use of complex-valued frequency dependent material models, illustrated by the shortcomings of the elastic hysteretic model...

  8. Eddy damping effect of additional conductors in superconducting levitation systems

    Science.gov (United States)

    Jiang, Zhao-Fei; Gou, Xiao-Fan

    2015-12-01

    Passive superconducting levitation systems consisting of a high temperature superconductor (HTSC) and a permanent magnet (PM) have demonstrated several fascinating applications such as the maglev system, flywheel energy storage. Generally, for the HTSC-PM levitation system, the HTSC with higher critical current density Jc can obtain larger magnetic force to make the PM levitate over the HTSC (or suspended below the HTSC), however, the process of the vibration of the levitated PM, provides very limited inherent damping (essentially hysteresis). To improve the dynamic stability of the levitated PM, eddy damping of additional conductors can be considered as the most simple and effective approach. In this article, for the HTSC-PM levitation system with an additional copper damper attached to the HTSC, we numerically and comprehensively investigated the damping coefficient c, damping ratio, Joule heating of the copper damper, and the vibration frequency of the PM as well. Furthermore, we comparatively studied four different arrangements of the copper damper, on the comprehensive analyzed the damping effect, efficiency (defined by c/VCu, in which VCu is the volume of the damper) and Joule heating, and finally presented the most advisable arrangement.

  9. Free vibration analysis of a rotating hub-functionally graded material beam system with the dynamic stiffening effect

    Science.gov (United States)

    Li, L.; Zhang, D. G.; Zhu, W. D.

    2014-02-01

    A comprehensive dynamic model of a rotating hub-functionally graded material (FGM) beam system is developed based on a rigid-flexible coupled dynamics theory to study its free vibration characteristics. The rigid-flexible coupled dynamic equations of the system are derived using the method of assumed modes and Lagrange's equations of the second kind. The dynamic stiffening effect of the rotating hub-FGM beam system is captured by a second-order coupling term that represents longitudinal shrinking of the beam caused by the transverse displacement. The natural frequencies and mode shapes of the system with the chordwise bending and stretching (B-S) coupling effect are calculated and compared with those with the coupling effect neglected. When the B-S coupling effect is included, interesting frequency veering and mode shift phenomena are observed. A two-mode model is introduced to accurately predict the most obvious frequency veering behavior between two adjacent modes associated with a chordwise bending and a stretching mode. The critical veering angular velocities of the FGM beam that are analytically determined from the two-mode model are in excellent agreement with those from the comprehensive dynamic model. The effects of material inhomogeneity and graded properties of FGM beams on their dynamic characteristics are investigated. The comprehensive dynamic model developed here can be used in graded material design of FGM beams for achieving specified dynamic characteristics.

  10. Modeling and Analysis of Composite Wing Sections for Improved Aeroelastic and Vibration Characteristics Using Smart Materials

    Science.gov (United States)

    Chattopadhyay, Aditi

    1996-01-01

    The objective of this research is to develop analysis procedures to investigate the coupling of composite and smart materials to improve aeroelastic and vibratory response of aerospace structures. The structural modeling must account for arbitrarily thick geometries, embedded and surface bonded sensors and actuators and imperfections, such as delamination. Changes in the dynamic response due to the presence of smart materials and delaminations is investigated. Experiments are to be performed to validate the proposed mathematical model.

  11. Vibrational study on the bioactivity of Portland cement-based materials for endodontic use

    Science.gov (United States)

    Taddei, P.; Tinti, A.; Gandolfi, M. G.; Rossi, P. L.; Prati, C.

    2009-04-01

    The bioactivity of a modified Portland cement (wTC) and a phosphate-doped wTC cement (wTC-P) was studied at 37 °C in Dulbecco's Phosphate Buffered Saline (DPBS). The cements, prepared as disks, were analysed at different ageing times (from 1 day to 2 months) by micro-Raman and ATR/FT-IR spectroscopies. The presence of deposits on the surface of the cements and the composition changes as a function of the storage time were investigated. The presence of an apatite deposit on the surface of both cements was already revealed after one day of ageing in DPBS. The trend of the I 965/I 991 Raman intensity ratio indicated the formation of a meanly thicker apatite deposit on the wTC-P cement at all the investigated times. This result was confirmed by the trend of the I 1030/I 945 IR intensity ratio calculated until 14 days of ageing. At 2 months, the thickness of the apatite deposit on wTC and wTC-P was about 200 and 500 μm, respectively, as estimated by micro-Raman spectroscopy, confirming the higher bioactivity of the phosphate-doped cement. Vibrational techniques allowed to gain more insights into the cement transformation and the different hydration rates of the various cement component. The setting of the cement and the formation of the hydrated silicate gel (C-S-H phase) was spectroscopically monitored through the I 830/I 945 IR intensity ratio.

  12. Flow-Induced Vibration of Circular Cylindrical Structures

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Shoei-Sheng [Argonne National Lab. (ANL), Argonne, IL (United States). Components Technology Division

    1985-06-01

    Flow-induced vibration is a term to denote those phenomena associated with the response of structures placed in or conveying fluid flow. More specifically, the terra covers those cases in which an interaction develops between fluid-dynamic forces and the inertia, damping or elastic forces in the structures. The study of these phenomena draws on three disciplines: (1) structural mechanics, (2) mechanical vibration, and (3) fluid dynamics. The vibration of circular cylinders subject to flow has been known to man since ancient times; the vibration of a wire at its natural frequency in response to vortex shedding was known in ancient Greece as aeolian tones. But systematic studies of the problem were not made until a century ago when Strouhal established the relationship between vortex shedding frequency and flow velocity for a given cylinder diameter. The early research in this area has beer summarized by Zdravkovich (1985) and Goldstein (1965). Flow-induced structural vibration has been experienced in numerous fields, including the aerospace industry, power generation/transmission (turbine blades, heat exchanger tubes, nuclear reactor components), civil engineering (bridges, building, smoke stacks), and undersea technology. The problems have usually been encountered or created accidentally through improper design. In most cases, a structural or mechanical component, designed to meet specific objectives, develops problems when the undesired effects of flow field have not been accounted for in the design. When a flow-induced vibration problem is noted in the design stage, the engineer has different options to eliminate the detrimental vibration. Unfortunately, in many situations, the problems occur after the components are already in operation; the "fix" usually is very costly. Flow-induced vibration comprises complex and diverse phenomena; subcritical vibration of nuclear fuel assemblies, galloping of transmission lines, flutter of pipes conveying fluid, and whirling

  13. Interfacial stresses in vibration of multilayer composite materials: experimental and theoretical analysis

    Science.gov (United States)

    Agbossou, Amen; Barthod, Christine; Teisseyre, Yves; Gautier, Gérard

    2005-12-01

    In laminated composites, interfaces are the transfer spots of mechanical charges, mechanical over-stress adaptations and energy dissipations. In order to examine the dynamic effects of interface stresses, we have inserted a thin layer of piezoelectric material at the interface of composite plies of a multilayer cantilever beam excited in bending. The voltage signals generated by the piezoelectric elements are seen to be dependent on the expected interlaminar stresses. Moreover, the realized experimental set-up validates the parameters of finite element simulations. Using the implemented finite element model, two different piezoelectric materials are compared with regard to their possibility for interfacial stress measurement and for mechanical energy dissipation.

  14. Serum proteomes of hypertension patients with abundant phlegm-dampness.

    Science.gov (United States)

    Chu, Yu-guang; Shi, Jie; Hu, Yuan-hui; Wu, Hua-qin; Liu, Gui-jian; Hu, Chao-jun; Li, Yong-zhe; Li, Yi; Chen, Zi-jing; He, Qing

    2009-07-01

    group and the control group are the material foundation of abundant phlegm-dampness. The selected differentiated proteins can be used to distinguish the EH patients with abundant phlegm-dampness from the healthy persons and the EH patients with non-phlegm-dampness. The molecular biology diagnosis model can offer an objective and accurate way for TCM syndrome differentiation.

  15. DFT computations on: Crystal structure, vibrational studies and optical investigations of a luminescent self-assembled material.

    Science.gov (United States)

    Kessentini, A; Ben Ahmed, A; Dammak, T; Belhouchet, M

    2018-02-15

    The current work undertakes the growth and the physicochemical properties of a novel green-yellow luminescence semi-organic material, the 3-picolylammonium bromide abbreviated (Pico-Br). In this paper, we report the X-ray diffraction measurements which show that the crystal lattice consists of distinct 3-picolylammonium cations and free bromide anions connected via NH⋯Br and NH⋯N hydrogen bonds leading to form a two dimensional frameworks. Molecular geometry compared with its optimized counterpart shows that the quantum chemical calculations carried out with density functional method (DFT) well produce the perceived structure by X-ray resolution of the studied material. To provide further insight into the spectroscopic properties, additional characterization of this material have been performed with Raman and infrared studies at room temperature. Theoretical computations have been computed using the (DFT) method at B3LYP/LanL2DZ level of theory implemented within Gaussian 03 program to study the vibrational spectra of the investigated molecule in the ground state. Optical absorption spectrum inspected by UV-visible absorption reveals the appearance of sharp optical gap of 280nm (4.42eV) as well as a strong green photoluminescence emission at 550nm (2.25eV) is detected on the photoluminescence (PL) spectrum at room temperature. Using the TD/DFT method, HOMO-LUMO energy gap and the Mulliken atomic charges were calculated in order to get an insight into the material. Good agreement between the theoretical results and the experimental ones was predicted. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. DFT computations on: Crystal structure, vibrational studies and optical investigations of a luminescent self-assembled material

    Science.gov (United States)

    Kessentini, A.; Ben Ahmed, A.; Dammak, T.; Belhouchet, M.

    2018-02-01

    The current work undertakes the growth and the physicochemical properties of a novel green-yellow luminescence semi-organic material, the 3-picolylammonium bromide abbreviated (Pico-Br). In this paper, we report the X-ray diffraction measurements which show that the crystal lattice consists of distinct 3-picolylammonium cations and free bromide anions connected via Nsbnd H ⋯ Br and Nsbnd H ⋯ N hydrogen bonds leading to form a two dimensional frameworks. Molecular geometry compared with its optimized counterpart shows that the quantum chemical calculations carried out with density functional method (DFT) well produce the perceived structure by X-ray resolution of the studied material. To provide further insight into the spectroscopic properties, additional characterization of this material have been performed with Raman and infrared studies at room temperature. Theoretical computations have been computed using the (DFT) method at B3LYP/LanL2DZ level of theory implemented within Gaussian 03 program to study the vibrational spectra of the investigated molecule in the ground state. Optical absorption spectrum inspected by UV-visible absorption reveals the appearance of sharp optical gap of 280 nm (4.42 eV) as well as a strong green photoluminescence emission at 550 nm (2.25 eV) is detected on the photoluminescence (PL) spectrum at room temperature. Using the TD/DFT method, HOMO-LUMO energy gap and the Mulliken atomic charges were calculated in order to get an insight into the material. Good agreement between the theoretical results and the experimental ones was predicted.

  17. On Landau damping

    KAUST Repository

    Mouhot, Clément

    2011-09-01

    Going beyond the linearized study has been a longstanding problem in the theory of Landau damping. In this paper we establish exponential Landau damping in analytic regularity. The damping phenomenon is reinterpreted in terms of transfer of regularity between kinetic and spatial variables, rather than exchanges of energy; phase mixing is the driving mechanism. The analysis involves new families of analytic norms, measuring regularity by comparison with solutions of the free transport equation; new functional inequalities; a control of non-linear echoes; sharp "deflection" estimates; and a Newton approximation scheme. Our results hold for any potential no more singular than Coulomb or Newton interaction; the limit cases are included with specific technical effort. As a side result, the stability of homogeneous equilibria of the non-linear Vlasov equation is established under sharp assumptions. We point out the strong analogy with the KAM theory, and discuss physical implications. Finally, we extend these results to some Gevrey (non-analytic) distribution functions. © 2011 Institut Mittag-Leffler.

  18. Study of special spacer with damping device for suppressing wake galloping in tandem cables of cable-stayed bridges and its application to full scale bridge; Nendanseitai wo riyoshita heiretsu cable yo gensui kinotsuki spacer to sono jikkyo cable eno tekiyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yoneda, M.; Setouchi, H.; Yoshioka, A. [Kawada Industries Inc., Tokyo (Japan); Shimoda, I.; Kawahara, S. [Oiles Corp., Tokyo (Japan)

    1996-12-20

    Cable vibration called wake galloping occurs in a cable-stayed bridge, in which cables are arranged tandem, and suppression of the vibration is an extremely important discussion item. This paper describes a complex eigen value analysis performed on tandem cables having lengths of 200 m and 100 m. The analysis revealed that damping characteristics added by a spacer system with a damping device (a type to install a visco-elastic body at about middle of the tandem cables via a jig) depend largely on torsional rigidity of the cables; and the characteristics may vary with difference in intervals between cable centers and that in cable diameters. A visco-elastic damping material of an asphalt system and a spacer with a damping device used as a spring material were fabricated and applied to a full scale bridge to identify quantitatively the damping addition characteristics of this system. Furthermore, the results of tests on the full scale bridge were compared with the result of the complex eigen value analysis, from which findings useful for actual works were obtained. 18 refs., 17 figs., 6 tabs.

  19. Free Vibration and Dynamic Stability of Functionally Graded Material Plates on Elastic Foundation

    OpenAIRE

    I. Ramu; S.C. Mohanty

    2015-01-01

    The study of parametric resonance characteristics of functionally-graded material (FGM) plates on elastic foundation is proposed under biaxial in plane periodic load. Finite element method in conjunction with Hamilton’s principle is utilised to establish the governing equations in a discrete form, Floquet’s theory was applied to determine the instability regions of FGM plate resting on elastic foundation. The effects of power law index, temperature rise, and foundation coefficients on the nat...

  20. Damping Characterization of Friction Energy Dissipation for Particle Systems Based on Powder Mechanics and Experimental Verification

    Directory of Open Access Journals (Sweden)

    Wangqiang XIAO

    2014-04-01

    Full Text Available We established a friction energy dissipation model for particle damping based on powder mechanics. We investigated the influence of geometric features of the damper on damping characteristics; and the geometric feature studied was the depth and length of the rectangular particle container. The work done by the frictional force between the particle layer and the effect of particle filling rate on the vibration damping characteristics was also explored. We analyzed the friction energy dissipation model, and the relationship between the particle filling rate and the vibration damping. The experimental results show good agreement with the friction energy dissipation model, which verifies the proposed simulation prediction. The results have shown that the particle damping technology can greatly consume the structure kinetic energy, and the vibration reduction effect of particle damping depends mainly on the interaction of the particles near the top. A proper filling rate of particle systems can result in an optimal effect on vibration reduction, which will provide the engineering applications with the theoretical guidance and design criteria.

  1. Damping-tunable energy-harvesting vehicle damper with multiple controlled generators: Design, modeling and experiments

    Science.gov (United States)

    Xie, Longhan; Li, Jiehong; Li, Xiaodong; Huang, Ledeng; Cai, Siqi

    2018-01-01

    Hydraulic dampers are used to decrease the vibration of a vehicle, where vibration energy is dissipated as heat. In addition to resulting in energy waste, the damping coefficient in hydraulic dampers cannot be changed during operation. In this paper, an energy-harvesting vehicle damper was proposed to replace traditional hydraulic dampers. The goal is not only to recover kinetic energy from suspension vibration but also to change the damping coefficient during operation according to road conditions. The energy-harvesting damper consists of multiple generators that are independently controlled by switches. One of these generators connects to a tunable resistor for fine tuning the damping coefficient, while the other generators are connected to a control and rectifying circuit, each of which both regenerates electricity and provides a constant damping coefficient. A mathematical model was built to investigate the performance of the energy-harvesting damper. By controlling the number of switched-on generators and adjusting the value of the external tunable resistor, the damping can be fine tuned according to the requirement. In addition to the capability of damping tuning, the multiple controlled generators can output a significant amount of electricity. A prototype was built to test the energy-harvesting damper design. Experiments on an MTS testing system were conducted, with results that validated the theoretical analysis. Experiments show that changing the number of switched-on generators can obviously tune the damping coefficient of the damper and simultaneously produce considerable electricity.

  2. OPTIMAL AUTOMOBILE MUFFLER VIBRATION AND NOISE ANALYSIS

    Directory of Open Access Journals (Sweden)

    Sujit Kumar Jha

    2013-06-01

    Full Text Available The muffler is the main part of the Automobile Exhaust System, consisting of fibrous and porous materials to absorb noise and vibrations. The exhaust gas mass coming from the engine can produce resonance, which may be the source of fatigue failure in the exhaust pipe due to the presence of continuous resonance. The modes on the muffler should be located away from the engine’s operating frequencies in order to minimise the resonance. The objective of this paper is to determine the frequencies that appear at the modes, which have the more adverse effect during the operation of the automobile. An impact test has been conducted by applying the force using a hard head hammer, and data generated have been used for plotting a graph of the transfer functions using MATLAB. Six points have been selected, namely 1, 2, 3, 4, 7, and 11 on the muffler for the impact test. The collected data from theses six points have been analysed for the addition of damping. Results suggests that increasing the mass increases the damping and lowers the modes of the transfer function. Further research will identify higher strength materials that can withstand the higher gas temperatures as well as the corrosion and erosion by the gas emitted from the engine.

  3. The Shock and Vibration Digest. Volume 12, Number 10,

    Science.gov (United States)

    1980-10-01

    bearings [243]. A pressurized gas damping, and the vibrations of damped structures. squeeze film has also been used as a journal damper ...2251 Key Words: Bearings , Gas bearings , Journal bearings , Whirl- Torsional Oscillations of the Rotor Disc for Horizon- ing, Squeeze - film dampers tal... Squeeze Film Highly Damped Structures," Shock Vib. Dig., Journal Damper ," Rep. No. NASA-CR-155533 9 (7), pp 3-11 (July 1977). (Dec 1977). 235. Rusnak,

  4. Nondestructive determination of fatigue crack damage in composites using vibration tests.

    Science.gov (United States)

    Dibenedetto, A. T.; Gauchel, J. V.; Thomas, R. L.; Barlow, J. W.

    1972-01-01

    The vibration response of glass reinforced epoxy and polyester laminates was investigated. The complex modulus and the damping capacity were measured as fatigue crack damage accumulated. Changes in the Young's modulus as well as the damping capacity correlated with the amount of crack damage. The damping was especially sensitive to debonding of the reinforcement from the resin matrix. Measurement of these vibration response changes shows promise as a means to nondestructively test the structural integrity of filament-reinforced composite structural members.

  5. Free Vibrations of Uniform Pipes Made From Composite Materials at an Internal Flow Under Effect of Additional Boundary Conditions

    Directory of Open Access Journals (Sweden)

    Nawal H. Al – Raheimy

    2016-09-01

    Full Text Available In this paper the approximate method of Raleigh method can be used to study the effect of additional boundary conditions (clamped – free & clamped – clamped on the free transverse vibrations of uniform pipes which have length, L (1m , inner radius, "Ri" (1cm & thickness, "t" (1mm made from composite materials, where the resin of unsaturated polyester represented the matrix material reinforced by aligned (E-fibers glass in the first case and used aligned fiber (Kevlar-49 in the second case. The length of fibers is in the two types, the first type is long fibers (continuous and the second is short fibers (discontinuous for different length all at volume fraction of fibers, "f" (0.15 & 0.25. At any construction of the pipe in composite material the natural frequency decreased when the velocity of flow increased from zero to critical velocity also can be observed the pipe at clamped – clamped boundary conditions predicts natural frequency & critical velocity greater than that pipe at clamped – free. The natural frequency and critical velocity increase with increasing volume fraction and length of discontinuous fiber. The value of natural frequency for pipes which have continuous fibers is constant at certain velocity of flow while are variable in pipes which have discontinuous fibers according to ratio between length of short fiber to critical length of discontinuous fiber whereas the natural frequency increase with increasing this ratio. Finally the pipes with Kevlar fiber have high critical velocity and natural frequency compare with pipes for fiber glass.

  6. A computational investigation of the transient response of an unbalanced rigid rotor flexibly supported and damped by short magnetorheological squeeze film dampers

    Science.gov (United States)

    Zapoměl, J.; Ferfecki, P.; Forte, P.

    2012-10-01

    Due to manufacturing and assembly inaccuracies, real rotors are always slightly imbalanced. This produces their lateral vibration and forces that are transmitted through the bearings to the stationary parts. The oscillation of the system can be reduced if damping devices are added to the constraint elements. To achieve the optimum performance of the rotor in a wide range of angular velocities and when passing through the critical speeds their damping effect must be controllable. For this purpose, the application of semiactive magnetorheological (MR) dampers has been analysed. The investigated problem focuses on studying the influence of their damping effect and of its control on the amplitude of the rotor vibration, on the magnitude of the force transmitted to the rotor casing, and on the amount of dissipative power generated in the MR films. The developed mathematical model assumes cavitation in the lubricating layer, and the MR liquid is modelled as a Bingham material. The derivation of the equation governing the pressure distribution in the oil film is completed by a new methodology making it possible to determine the yielding shear stress needed for its solution. The equations of motion of the rotor are nonlinear due to the damping forces and to solve them a Runge-Kutta integration method was applied. Computer simulations show that a suitably proposed current-rotor angular speed relationship enables one to fully eliminate the resonance peaks and to achieve the optimum compromise between the attenuation of the rotor lateral vibration, the magnitude of the forces transmitted to the rotor casing and the amount of energy dissipated in the lubricating layers.

  7. Thermoelastic damping in torsion microresonators with coupling effect between torsion and bending

    Science.gov (United States)

    Tai, Yongpeng; Li, Pu; Fang, Yuming

    2014-02-01

    Predicting thermoelastic damping (TED) is crucial in the design of high Q MEMS resonators. In the past, there have been few works on analytical modeling of thermoelastic damping in torsion microresonators. This could be related to the assumption of pure torsional mode for the supporting beams in the torsion devices. The pure torsional modes of rectangular supporting beams involve no local volume change, and therefore, they do not suffer any thermoelastic loss. However, the coupled motion of torsion and bending usually exists in the torsion microresonator when it is not excited by pure torque. The bending component of the coupled motion causes flexural vibrations of supporting beams which may result in significant thermoelastic damping for the microresonator. This paper presents an analytical model for thermoelastic damping in torsion microresonators with the coupling effect between torsion and bending. The theory derives a dynamic model for torsion microresonators considering the coupling effect, and approximates the thermoelastic damping by assuming the energy loss to occur only in supporting beams of flexural vibrations. The thermoelastic damping obtained by the present model is compared to the measured internal friction of single paddle oscillators. It is found that thermoelastic damping contributes significantly to internal friction for the case of the higher modes at room temperature. The present model is validated by comparing its results with the finite-element method (FEM) solutions. The effects of structural dimensions and other parameters on thermoelastic damping are investigated for the representative case of torsion microresonators.

  8. The Vibration Ring. Phase 1; [Seedling Fund

    Science.gov (United States)

    Asnani, Vivake M.; Krantz, Timothy L.; Delap, Damon C.; Stringer, David B.

    2014-01-01

    The vibration ring was conceived as a driveline damping device to prevent structure-borne noise in machines. It has the appearance of a metal ring, and can be installed between any two driveline components like an ordinary mechanical spacer. Damping is achieved using a ring-shaped piezoelectric stack that is poled in the axial direction and connected to an electrical shunt circuit. Surrounding the stack is a metal structure, called the compression cage, which squeezes the stack along its poled axis when excited by radial driveline forces. The stack in turn generates electrical energy, which is either dissipated or harvested using the shunt circuit. Removing energy from the system creates a net damping effect. The vibration ring is much stiffer than traditional damping devices, which allows it to be used in a driveline without disrupting normal operation. In phase 1 of this NASA Seedling Fund project, a combination of design and analysis was used to examine the feasibility of this concept. Several designs were evaluated using solid modeling, finite element analysis, and by creating prototype hardware. Then an analytical model representing the coupled electromechanical response was formulated in closed form. The model was exercised parametrically to examine the stiffness and loss factor spectra of the vibration ring, as well as simulate its damping effect in the context of a simplified driveline model. The results of this work showed that this is a viable mechanism for driveline damping, and provided several lessons for continued development.

  9. Modeling of Axial Spring Stiffness in Active Vibration Controlled Drilling

    Directory of Open Access Journals (Sweden)

    Pao William

    2014-07-01

    Full Text Available During drilling process, substantial amount of vibration and shock are induced to the drill string. Active vibration controlled drilling is introduced to reduce the vibration and increase the efficiency of drilling process. In this system, two main components that determine the damping coefficient are magnetorheological (MR damper and spring assembly. Performance of vibration damping system is depending on the viscosity of MR fluid in the damper and spring constant of spring assembly. One of the key issues that are unclear from the design is the correlation between the axial spring stiffness configuration and the damping force which needs to be tuned actively. There has been lack of studies on how the viscosity of MR fluid on the active vibration damper affects the damping stiffness of the whole system. The objective of the project is to extract the correlations for the viscous damping coefficient, equivalent spring stiffness and power input to the system. Simplified vibration model is thus created using Simulink, together with experimental data fed from APS Technology’s in-house team. Inputs of the simulation such as force exerted, mass of mandrel, spring constant and step time are based on the experimental data and can be adjusted to suit different experiments. By having the model, behavior of the system can be studied and analyzed. From the simulation, it is also observed that the relationship between damping coefficient and power input of the system is linear.

  10. Damping Effect of Humans

    DEFF Research Database (Denmark)

    Pedersen, Lars

    Passive humans (sitting or standing) might well be present on flooring-systems, footbridges or other structures that carry humans. An active croud of people might generate structural vibrations, and these might be problematic. The passive crowd of people, however, will interact with the structura...

  11. Damping Effect of Humans

    DEFF Research Database (Denmark)

    Pedersen, Lars

    Passive humans (sitting or standing) might well be present on flooring-systems, footbridges or other structures that carry humans. An active croud of people might generate structural vibrations, and these might be problematic. The passive crowd of people, however, will interact with the structural...

  12. Optical table with embedded active vibration dampers (smart table)

    Science.gov (United States)

    Ryaboy, Vyacheslav M.; Kasturi, Prakash S.; Nastase, Adrian S.; Rigney, Thomas K.

    2005-05-01

    This paper describes the actively damped optical table developed and introduced as a standard product, ST series SmartTable(TM), by Newport Corporation. The active damping system is self-adjusting and robust with respect to changes in payload and vibration environment. It outperforms not only the broadband damped optical tables, but also the top-of-the-line tables equipped with tuned passive vibration absorbers. The maximum resonance vibration amplitudes are reduced about ten times. Additionally, the user has the benefit of being able to monitor and analyze vibration of the table by the conditioned low-noise signals from the embedded vibration sensors. Theoretical background, analysis, design rationale and experimental verification of the system are presented, with emphasis on sensor-actuator pairs architecture, signal processing and adaptive controls.

  13. The Duffing oscillator with damping

    DEFF Research Database (Denmark)

    Johannessen, Kim

    2015-01-01

    An analytical solution to the differential equation describing the Duffing oscillator with damping is presented. The damping term of the differential equation and the initial conditions satisfy an algebraic equation, and thus the solution is specific for this type of damping. The nonlinear term....... It is established that the period of oscillation is shorter compared to that of a linearized model but increasing with time and asymptotically approaching the period of oscillation of the linear damped model. An explicit expression for the period of oscillation has been derived, and it is found to be very accurate....

  14. Chiral damping of magnetic domain walls

    KAUST Repository

    Jué, Emilie

    2015-12-21

    Structural symmetry breaking in magnetic materials is responsible for the existence of multiferroics1, current-induced spin–orbit torques2, 3, 4, 5, 6, 7 and some topological magnetic structures8, 9, 10, 11, 12. In this Letter we report that the structural inversion asymmetry (SIA) gives rise to a chiral damping mechanism, which is evidenced by measuring the field-driven domain-wall (DW) motion in perpendicularly magnetized asymmetric Pt/Co/Pt trilayers. The DW dynamics associated with the chiral damping and those with Dzyaloshinskii–Moriya interaction (DMI) exhibit identical spatial symmetry13, 14, 15, 16, 17, 18, 19. However, both scenarios are differentiated by their time reversal properties: whereas DMI is a conservative effect that can be modelled by an effective field, the chiral damping is purely dissipative and has no influence on the equilibrium magnetic texture. When the DW motion is modulated by an in-plane magnetic field, it reveals the structure of the internal fields experienced by the DWs, allowing one to distinguish the physical mechanism. The chiral damping enriches the spectrum of physical phenomena engendered by the SIA, and is essential for conceiving DW and skyrmion devices owing to its coexistence with DMI (ref. 20).

  15. Do Lumped-Parameter Models Provide the Correct Geometrical Damping?

    DEFF Research Database (Denmark)

    Andersen, Lars

    2007-01-01

    This paper concerns the formulation of lumped-parameter models for rigid footings on homogenous or stratified soil with focus on the horizontal sliding and rocking. Such models only contain a few degrees of freedom, which makes them ideal for inclusion in aero-elastic codes for wind turbines and ......-parameter models with respect to the prediction of the maximum response during excitation and the geometrical damping related to free vibrations of a footing....

  16. CONTRIBUTIONS TO THE STUDY OF THE VIBRATIONS FREQUENCY OF THE DRILL TOOL IN THE PROCESS OF MANUFACTURING THE BRONZE MATERIALS

    Directory of Open Access Journals (Sweden)

    Cosmin-Mihai MIRIŢOIU

    2013-05-01

    Full Text Available In this paper we present the experimental testings used to study the vibration of the drill tool, during the drilling of the bronze products. We have used the experimental setup presented in Miriţoiu (2013[1]. In this paper the vibrations are analyzed during the drilling on the universal lathe machines. The main purpose of to find a correlation between the cutting speed and the frequency of the vibration by using the experimental results and the regression analysis

  17. Grain size effects on stability of nonlinear vibration with nanocrystalline NiTi shape memory alloy

    Science.gov (United States)

    Xia, Minglu; Sun, Qingping

    2017-10-01

    Grain size effects on stability of thermomechanical responses for a nonlinear torsional vibration system with nanocrystalline superelastic NiTi bar are investigated in the frequency and amplitude domains. NiTi bars with average grain size from 10 nm to 100 nm are fabricated through cold-rolling and subsequent annealing. Thermomechanical responses of the NiTi bar as a softening nonlinear damping spring in the torsional vibration system are obtained by synchronised acquisition of rotational angle and temperature under external sinusoidal excitation. It is shown that nonlinearity and damping capacity of the NiTi bar decrease as average grain size of the material is reduced below 100 nm. Therefore jump phenomena of thermomechanical responses become less significant or even vanish and the vibration system becomes more stable. The work in this paper provides a solid experimental base for manipulating the undesired jump phenomena of thermomechanical responses and stabilising the mechanical vibration system through grain refinement of NiTi SMA.

  18. Damping and support in high-temperature superconducting levitation systems

    Energy Technology Data Exchange (ETDEWEB)

    Hull, John R [Sammamish, WA; McIver, Carl R [Everett, WA; Mittleider, John A [Kent, WA

    2009-12-15

    Methods and apparatuses to provide improved auxiliary damping for superconducting bearings in superconducting levitation systems are disclosed. In a superconducting bearing, a cryostat housing the superconductors is connected to a ground state with a combination of a damping strip of material, a set of linkage arms to provide vertical support, and spring washers to provide stiffness. Alternately, the superconducting bearing may be supported by a cryostat connected to a ground state by posts constructed from a mesh of fibers, with the damping and stiffness controlled by the fiber composition, size, and mesh geometry.

  19. Transfer function method for frequency response and damping effect of multilayer PCLD on cylindrical shell

    Science.gov (United States)

    Qiu, Q.; Fang, Z. P.; Wan, H. C.; Zheng, L.

    2013-07-01

    Based on the Donnell assumptions and linear visco-elastic theory, the constitutive equations of the cylindrical shell with multilayer Passive Constrained Layer Damping (PCLD) treatments are described. The motion equations and boundary conditions are derived by Hamilton principle. After trigonometric series expansion and Laplace transform, the state vector is introduced and the dynamic equations in state space are established. The transfer function method is used to solve the state equation. The dynamic performance including the natural frequency, the loss factor and the frequency response of clamped-clamped multi-layer PCLD cylindrical shell is obtained. The results show that multi-layer PCLD cylindrical shell is more effective than the traditional three-layer PCLD cylindrical shell in suppressing vibration and noise if the same amount of material is applied. It demonstrates a potential application of multi-layer PCLD treatments in many critical structures such as cabins of aircrafts, hulls of submarines and bodies of rockets and missiles.

  20. Experimental validation of solid rocket motor damping models

    Science.gov (United States)

    Riso, Cristina; Fransen, Sebastiaan; Mastroddi, Franco; Coppotelli, Giuliano; Trequattrini, Francesco; De Vivo, Alessio

    2017-12-01

    In design and certification of spacecraft, payload/launcher coupled load analyses are performed to simulate the satellite dynamic environment. To obtain accurate predictions, the system damping properties must be properly taken into account in the finite element model used for coupled load analysis. This is typically done using a structural damping characterization in the frequency domain, which is not applicable in the time domain. Therefore, the structural damping matrix of the system must be converted into an equivalent viscous damping matrix when a transient coupled load analysis is performed. This paper focuses on the validation of equivalent viscous damping methods for dynamically condensed finite element models via correlation with experimental data for a realistic structure representative of a slender launch vehicle with solid rocket motors. A second scope of the paper is to investigate how to conveniently choose a single combination of Young's modulus and structural damping coefficient—complex Young's modulus—to approximate the viscoelastic behavior of a solid propellant material in the frequency band of interest for coupled load analysis. A scaled-down test article inspired to the Z9-ignition Vega launcher configuration is designed, manufactured, and experimentally tested to obtain data for validation of the equivalent viscous damping methods. The Z9-like component of the test article is filled with a viscoelastic material representative of the Z9 solid propellant that is also preliminarily tested to investigate the dependency of the complex Young's modulus on the excitation frequency and provide data for the test article finite element model. Experimental results from seismic and shock tests performed on the test configuration are correlated with numerical results from frequency and time domain analyses carried out on its dynamically condensed finite element model to assess the applicability of different equivalent viscous damping methods to describe

  1. Persistent Motor Deficits in DAMP

    OpenAIRE

    J Gordon Millichap

    2000-01-01

    Motor control in ability to perform everyday and spare-time activities was assessed at 11 to 12 years of age in 10 boys with deficits in attention, motor control and perception (DAMP) and compared with a group of 20 boys without DAMP.

  2. CFD evaluation of added damping due to fluid flow over a hydroelectric turbine blade

    Science.gov (United States)

    Gauthier, J. P.; Giroux, A. M.; Etienne, S.; Gosselin, F. P.

    2016-11-01

    To estimate structural fatigue, vibrational response to realistic spectrum of excitations and associated equivalent damping are of paramount importance. In this paper, an approach to quantify flow-induced damping of a relatively heavy fluid on a vibrating hydraulic turbine blade using numerical simulations is presented. First, mode shapes and frequencies of the immersed structure are obtained by modal analysis using the finite element method. Then, forced oscillatory modal motion is prescribed on the structural boundary of unsteady Reynolds-averaged Navier-Stokes flow simulations. Damping is finally computed as the normalized work done by the resulting fluid load on the structure. Validation is achieved by comparing the numerical results with available experimental data for a steel hydrofoil oscillating in flowing water. For this case, the linear increase in the damping ratio with the flow velocity is reproduced within 10% of the experimental values. Application of the method to an actual hydroelectric propeller turbine blade yields a fluid damping value of around 15% of critical damping for its first vibration mode.

  3. Vibration Control in Periodic Structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker

    2017-01-01

    Within the framework of periodic structures, the calibration of RL shunted piezoelectric inclusions is investigated with respect to maximum damping of a particular wave form. A finite element setting is assumed, with local shunted inclusions inside the unit cell. The effect of the shunts is repre....... The presentation contains dispersion diagrams and vibration amplitude curves for the optimally calibrated RL shunt system in a 1-D periodic structure with local piezoelectric inclusions....

  4. A practical multiscale approach for optimization of structural damping

    DEFF Research Database (Denmark)

    Andreassen, Erik; Jensen, Jakob Søndergaard

    2016-01-01

    A simple and practical multiscale approach suitable for topology optimization of structural damping in a component ready for additive manufacturing is presented.The approach consists of two steps: First, the homogenized loss factor of a two-phase material is maximized. This is done in order...... to obtain a range of isotropic microstructures that have a connected stiff material phase. Second,the structural damping of the component is maximized using material interpolations based on the homogenized properties of the microstructures. In order to achieve convergence towards a discrete set of material...

  5. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2005-04-27

    The objective of this program is to develop a system to both monitor the vibration of a bottomhole assembly, and to adjust the properties of an active damper in response to these measured vibrations. Phase I of this program, which entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype, was completed on May 31, 2004. The principal objectives of Phase II are: more extensive laboratory testing, including the evaluation of different feedback algorithms for control of the damper; design and manufacture of a field prototype system; and, testing of the field prototype in drilling laboratories and test wells. As a result of the lower than expected performance of the MR damper noted last quarter, several additional tests were conducted. These dealt with possible causes of the lack of dynamic range observed in the testing: additional damping from the oil in the Belleville springs; changes in properties of the MR fluid; and, residual magnetization of the valve components. Of these, only the last was found to be significant. By using a laboratory demagnetization apparatus between runs, a dynamic range of 10:1 was achieved for the damper, more than adequate to produce the needed improvements in drilling. Additional modeling was also performed to identify a method of increasing the magnetic field in the damper. As a result of the above, several changes were made in the design. Additional circuitry was added to demagnetize the valve as the field is lowered. The valve was located to above the Belleville springs to reduce the load placed upon it and offer a greater range of materials for its construction. In addition, to further increase the field strength, the coils were relocated from the mandrel to the outer housing. At the end of the quarter, the redesign was complete and new parts were on order. The project is approximately three months behind schedule at this time.

  6. Sensor fusion for active vibration isolation in precision equipment

    NARCIS (Netherlands)

    Tjepkema, D.; van Dijk, Johannes; Soemers, Herman

    2012-01-01

    Sensor fusion is a promising control strategy to improve the performance of active vibration isolation systems that are used in precision equipment. Normally, those vibration isolation systems are only capable of realizing a low transmissibility. Additional objectives are to increase the damping

  7. The effect of geometric structure on stiffness and damping factor of wood applicable to machine tool structure

    Directory of Open Access Journals (Sweden)

    Susilo Adi Widyanto

    2013-06-01

    Full Text Available Stiffness and vibration damping capability are important criteria in design of machine tool structure. In other sides, the weight of machine tool structure must be reduced to increase  the handling capability. This paper presents  an analysis of the effect of geometric structure on stiffness and vibration damping of wood structure.  The stiffness was analysed  using numerical method, so called finite element method (FEM, while the vibration damping capability was experimentally tested. Vibration testing was also performed to wood structures with sand powder filled  into  its rectangular hole to observe the its effect on damping factor. Simulation results show  that the cross ribs structure yielded minimum mass reduction ratio compared to the three square holes as well as the single rectangular hole structures. While the vibration test results explained that the damping factor of Shorea laevis wood was higher than that Hevea braziiensis wood. The use of sand powder as vibrating  mass in closed-box structure effectively increased the damping capability, for single rectangular hole structure the damping factor was increased from 0.048 to 0.079doi: http://dx.doi.org/10.12777/ijse.4.2.2013.57-60[How to cite the article: Widyanto, S. A., Widodo, A., Nugroho, S., & Siahaan, D. (2013. The effect of geometric structure on stiffness and damping factor of wood applicable to machine tool structure. INTERNATIONAL JOURNAL OF SCIENCE AND ENGINEERING, 4(2, 57-60. doi: http://dx.doi.org/10.12777/ijse.4.2.2013.57-60

  8. Significant Attenuation of Lightly Damped Resonances Using Particle Dampers

    Science.gov (United States)

    Smith, Andrew; LaVerde, Bruce; Hunt, Ron; Knight, Joseph Brent

    2015-01-01

    When equipment designs must perform in a broad band vibration environment it can be difficult to avoid resonances that affect life and performance. This is especially true when an organization seeks to employ an asset from a heritage design in a new, more demanding vibration environment. Particle dampers may be used to provide significant attenuation of lightly damped resonances to assist with such a deployment of assets by including only a very minor set of modifications. This solution may be easier to implement than more traditional attenuation schemes. Furthermore, the cost in additional weight to the equipment can be very small. Complexity may also be kept to a minimum, because the particle dampers do not require tuning. Attenuating the vibratory response with particle dampers may therefore be simpler (in a set it and forget it kind of way) than tuned mass dampers. The paper will illustrate the use of an "equivalent resonance test jig" that can assist designers in verifying the potential resonance attenuation that may be available to them during the early trade stages of the design. An approach is suggested for transforming observed attenuation in the jig to estimated performance in the actual service design. KEY WORDS: Particle Damper, Performance in Vibration Environment, Damping, Resonance, Attenuation, Mitigation of Vibration Response, Response Estimate, Response Verification.

  9. Grain size and nanoscale effects on the nonlinear pull-in instability and vibrations of electrostatic actuators made of nanocrystalline material

    Science.gov (United States)

    Gholami, R.; Ansari, R.

    2018-01-01

    Presented herein is the study of grain size, grain surface energy and small scale effects on the nonlinear pull-in instability and free vibration of electrostatic nanoscale actuators made of nanocrystalline silicon (Nc-Si). A Mori–Tanaka micromechanical model is utilized to calculate the effective material properties of Nc-Si considering material structure inhomogeneity, grain size and grain surface energy. The small-scale effect is also taken into account using Mindlin’s strain gradient theory. Governing equations are derived in the discretized weak form using the variational differential quadrature method based on the third-order shear defamation beam theory in conjunction with the von Kármán hypothesis. The electrostatic actuation is modeled considering the fringing field effects based upon the parallel plate approximation. Moreover, the Casimir force effect is considered. The pseudo arc-length continuation technique is used to obtain the applied voltage-deflection curve of Nc-Si actuators. Then, a time-dependent small disturbance around the deflected configuration is assumed to solve the free vibration problem. By performing a numerical study, the influences of various factors such as length scale parameter, volume fraction of the inclusion phase, density ratio, average inclusion radius and Casimir force on the pull-in instability and free vibration of Nc-Si actuators are investigated.

  10. Optimization of the impact multi-mass vibration absorbers

    Directory of Open Access Journals (Sweden)

    Ivan Kernytskyy

    2017-09-01

    Full Text Available The problem of attaching dynamic vibration absorber (DVA to a discrete multi-degree-of-freedom or continuous structure has been outlined in many papers and monographs. An impact damping system can overcome some limitations by impact as the damping medium and impact mass interaction as the damping mechanism. The paper contemplates the provision of DVA with the several of the impact masses. Such originally designed absorbers reduce vibration selectively in maximum vibration mode without introducing vibration in other modes. An impact damper is a passive control device which takes the form of a freely moving mass, constrained by stops attached to the structure under control, i.e. the primary structure. The damping results from the exchange of momentum during impacts between the mass and the stops as the structure vibrates. The paper contemplates the provision of the impact multi-mass DVA’s with masses collisions for additional damping. For some cases of DVA optimization such a design seems more effective than conventional multi-mass DVA with independent mass moving. A technique is developed to give the optimal DVA’s for the elimination of excessive vibration in harmonic stochastic and impact loaded systems.

  11. Influence of squeeze film damping on the higher-order modes of clamped–clamped microbeams

    KAUST Repository

    Alcheikh, Nouha

    2016-05-06

    This paper presents an experimental study and a finite-element analysis of the effect of squeeze film damping on the resonance frequency and quality factor of the higher-order flexure vibrations modes of clamped-clamped microbeams. Viscoelastic and silicon nitride microbeams are fabricated and are electrostatically actuated by various electrode configurations to trigger the first, second, and third modes. The damping characteristic and the resonance frequency of these modes are examined for a wide range of gas pressure and electrostatic voltage loads. The results of the silicon nitride beams and viscoelastic beams are compared. It is found that the intrinsic material loss is the major dissipation mechanism at low pressure for the viscoelastic microbeams, significantly limiting their quality factor. It is also found that while the silicon nitride beams show higher quality factors at the intrinsic and molecular regimes of pressure, due to their low intrinsic loss, their quality factors near atmospheric pressure are lower than those of the viscoelastic microbeams. Further, the higher-order modes of all the beams show much higher quality factors at atmospheric pressure compared to the first mode, which could be promising for operating such resonators in air. Experimental results and finite element model simulations show good agreement for resonance frequency and quality factor for the three studied modes. © 2016 IOP Publishing Ltd.

  12. EXPERIMENTAL MONTAGE USED TO STUDY THE VIBRATION OF THE DRILL TOOL IN THE PROCESS OF MANUFACTURING THE BRONZE MATERIALS

    Directory of Open Access Journals (Sweden)

    Cosmin-Mihai MIRIŢOIU

    2013-05-01

    Full Text Available In this paper we present the experimental setup used to study the vibration of the drill tool, during the drilling of the bronze products. In this paper the vibrations are analyzed during the drilling on the universal lathe machines. This time, the tool is fixed in the movable boring head and will make a translation movement with constant feeding, and the workpiece spins around its axis of symmetry and it is fixed in the spindle head stock of the universal lathe machine

  13. Granular dampers for the reduction of vibrations of an oscillatory saw

    Science.gov (United States)

    Heckel, Michael; Sack, Achim; Kollmer, Jonathan E.; Pöschel, Thorsten

    2012-10-01

    Instruments for surgical and dental application based on oscillatory mechanics submit unwanted vibrations to the operator's hand. Frequently the weight of the instrument's body is increased to dampen its vibration. Based on recent research regarding the optimization of granular damping we developed a prototype granular damper that attenuates the vibrations of an oscillatory saw twice as efficiently as a comparable solid mass.

  14. Enhancing the Damping Properties of Viscoelastic Composites by Topology Optimization

    DEFF Research Database (Denmark)

    Andreasen, Casper Schousboe; Andreassen, Erik; Sigmund, Ole

    in engineering structures. Thus, materials or composites with high stiffness and high damping are of great interest to the industry. The inherent compromise between high stiffness and high damping in viscoelastic materials has been treated theoretically [2, 3] and experimentally [1]. It has been shown that high...... stiffness and high damping can be realized by Hashin-type composites or Rank-N laminates. However, in order to manufacture such composites it is favorable to obtain single length scale microstructures, i.e. without multiscale structures such that the materials can be manufactured by modern manufacturing...... techniques. As an example, by the use of e.g. SLM/SLS - Selective Laser Melting/Sintering, an open metallic microstructure can be printed and in a subsequent process the porespace can be filled with a high loss compliant material. Yi and co-workers [6] applied topology optimization to design the 2D...

  15. Vibrational resonance in the Morse oscillator

    Indian Academy of Sciences (India)

    Abstract. The occurrence of vibrational resonance is investigated in both classical and quantum mechanical Morse oscillators driven by a biharmonic force. The biharmonic force consists of two forces of widely different frequencies ω and with. ≫ ω. In the damped and biharmoni- cally driven classical Morse oscillator, ...

  16. Free-Vibration Analysis of Structures

    Science.gov (United States)

    Gupta, K. K.

    1985-01-01

    Improved numerical procedure more than twice as fast as previous methods. Unified numerical algorithm efficiently solves free-vibration problems of stationary or spinning structures with or without viscous or structural damping. Algorithm used to solve static problems involving multiple loads and to solve quadratic matrix eigenvalue problems associated with finite-dynamic-element structural discretization.

  17. Laserlike Vibrational Instability in Rectifying Molecular Conductors

    DEFF Research Database (Denmark)

    Lu, Jing Tao; Hedegård, Per; Brandbyge, Mads

    2011-01-01

    We study the damping of molecular vibrations due to electron-hole pair excitations in donor-acceptor (D-A) type molecular rectifiers. At finite voltage additional nonequilibrium electron-hole pair excitations involving both electrodes become possible, and contribute to the stimulated emission and...

  18. Tuning the vibration of a rotor with shape memory alloy metal rubber supports

    Science.gov (United States)

    Ma, Yanhong; Zhang, Qicheng; Zhang, Dayi; Scarpa, Fabrizio; Liu, Baolong; Hong, Jie

    2015-09-01

    The paper describes a novel smart rotor support damper with variable stiffness made with a new multifunctional material - the shape memory alloy metal rubber (SMA-MR). SMA-MR gives high load bearing capability (yield limit up to 100 MPa and stiffness exceeding 1e8 N/m), high damping (loss factor between 0.15 and 0.3) and variable stiffness (variation of 2.6 times between martensite and austenite phases). The SMA-MR has been used to replace a squeeze film damper and combined with an elastic support. The mechanical performance of the smart support damper has been investigated at room and high temperatures on a rotor test rig. The vibration tuning capabilities of the SMA-MR damper have been evaluated through FEM simulations and experimental tests. The study shows the feasibility of using the SMA-MR material for potential applications of active vibration control at different temperatures in rotordynamics systems.

  19. Adaptive tuned vibration absorber based on magnetorheological elastomer-shape memory alloy composite

    Science.gov (United States)

    Kumbhar, Samir B.; Chavan, S. P.; Gawade, S. S.

    2018-02-01

    Shape memory alloy (SMA) is an attractive smart material which could be used as stiffness tuning element in adaptive tuned vibration absorber (ATVA). The sharp modulus change in SMA material during phase transformation creates difficulties for smooth tuning to track forcing frequency to minimize vibrations of primary system. However, high hysteresis damping at low temperature martensitic phase degrades performance of vibration absorber. This paper deals with the study of dynamic response of system in which SMA and magnetorheological elastomer (MRE) are combined together to act as a smart spring- mass-damper system in a tuned vibration absorber. This composite is used as two way stiffness tuning element in ATVA for smooth and continuous tuning and to minimize the adverse effect at low temperature by increasing equivalent stiffness. The stiffnesses of SMA element and MRE are varied respectively by changing temperature and strength of external magnetic field. The two way stiffness tuning ability and adaptivity have been demonstrated analytically and experimentally. The experimental results show good agreement with analytical results. The proposed composite is able to shift the stiffness consequently the natural frequency of primary system as well as reduce the vibration level of primary system by substantial mount.

  20. Amplitude damping of vortex modes

    CSIR Research Space (South Africa)

    Dudley, Angela L

    2010-09-01

    Full Text Available An interferometer, mimicking an amplitude damping channel for vortex modes, is presented. Experimentally the action of the channel is in good agreement with that predicted theoretically. Since we can characterize the action of the channel on orbital...

  1. Spatial Damping of Linear Compressional Magnetoacoustic Waves ...

    Indian Academy of Sciences (India)

    shows greater wave damping at low values of radiative time and then attains some maximum value and then decreases. The slow mode wave has higher values of damping per wavelength, showing higher levels of damping due to radiation. For τR → ∞, the wave takes infinite time to damp and therefore travels very long ...

  2. Reducing Transmitted Vibration Using Delayed Hysteretic Suspension

    Directory of Open Access Journals (Sweden)

    Lahcen Mokni

    2011-01-01

    Full Text Available Previous numerical and experimental works show that time delay technique is efficient to reduce transmissibility of vibration in a single pneumatic chamber by controlling the pressure in the chamber. The present work develops an analytical study to demonstrate the effectiveness of such a technique in reducing transmitted vibrations. A quarter-car model is considered and delayed hysteretic suspension is introduced in the system. Analytical predictions based on perturbation analysis show that a delayed hysteretic suspension enhances vibration isolation comparing to the case where the nonlinear damping is delay-independent.

  3. Identification of Light Damping in Structures

    DEFF Research Database (Denmark)

    Jensen, J. L.; Brincker, Rune; Rytter, A.

    1990-01-01

    Different methods to identification of linear and nonlinear damping in lightly damped structures are discussed in this paper. The discussion is based on experiments with a 4 meter high monopile. Two alternative methods have been used for experimental cases of linear and nonlinear damping. Method 1...... case was a naturally damped monopile which was considered to be linear viscous damped. The second case was nonlinear viscous damping of the monopile due to a mounted damper on the monopile. The two cases illustrates identification of lightly damping in the linear and nonlinear case....

  4. Identification of Light Damping in Structures

    DEFF Research Database (Denmark)

    Jensen, Jacob Laigaard; Brincker, Rune; Rytter, Anders

    Different methods to identification of linear and nonlinear damping in lightly damped structures are discussed in this paper. The discussion is based on experiments with a 4 meter high monopile. Two alternative methods have been used for experimental cases of linear and nonlinear damping. Method 1...... case was a naturally damped monopile which was considered to be linear viscous damped. The second case was nonlinear viscous damping of the monopile due to a mounted damper on the monopile. The two cases illustrate identification of lightly damping in the linear and the nonlinear case....

  5. Effect of shelf aging on vibration transmissibility of anti-vibration gloves.

    Science.gov (United States)

    Shibata, Nobuyuki

    2017-10-05

    Anti-vibration gloves have been used in real workplaces to reduce vibration transmitted through hand-held power tools to the hand. Generally materials used for vibration attenuation in gloves are resilient materials composed of certain synthetic and/or composite polymers. The mechanical characteristics of the resilient materials used in anti-vibration gloves are prone to be influenced by environmental conditions such as temperature, humidity, and photo-irradiation, which cause material degradation and aging. This study focused on the influence of shelf aging on the vibration attenuation performance of air-packaged anti-vibration gloves following 2 years of shelf aging. Effects of shelf aging on the vibration attenuation performance of anti-vibration gloves were examined according to the Japan industrial standard JIS T8114 test protocol. The findings indicate that shelf aging induces the reduction of vibration attenuation performance in air-packaged anti-vibration gloves.

  6. Buzz off! An evaluation of ultrasonic acoustic vibration for the disruption of marine micro-organisms on sensor-housing materials.

    Science.gov (United States)

    McQuillan, J S; Hopper, D J; Magiopoulos, I; Arundell, M; Brown, R; Shorter, S; Mowlem, M C; Pascal, R W; Connelly, D

    2016-12-01

    Biofouling is a process of ecological succession which begins with the attachment and colonization of micro-organisms to a submerged surface. For marine sensors and their housings, biofouling can be one of the principle limitations to long-term deployment and reliability. Conventional antibiofouling strategies using biocides can be hazardous to the environment, and therefore alternative chemical-free methods are preferred. In this study, custom-made testing assemblies were used to evaluate ultrasonic vibration as an antibiofouling process for marine sensor-housing materials over a 28-day time course. Microbial biofouling was measured based on (i) surface coverage, using fluorescence microscopy and (ii) bacterial 16S rDNA gene copies, using Quantitative polymerase chain reaction (PCR). Ultrasonic vibrations (20 KHz, 200 ms pulses at 2-s intervals; total power 16·08 W) significantly reduced the surface coverage on two plastics, poly(methyl methacrylate) and polyvinyl chloride (PVC) for up to 28 days. Bacterial gene copy number was similarly reduced, but the results were only statistically significant for PVC, which displayed the greatest overall resistance to biofouling, regardless of whether ultrasonic vibration was applied. Copper sheet, which has intrinsic biocidal properties was resistant to biofouling during the early stages of the experiment, but inhibited measurements made by PCR and generated inconsistent results later on. In this study, ultrasonic acoustic vibration is presented as a chemical-free, ecologically friendly alternative to conventional methods for the perturbation of microbial attachment to submerged surfaces. The results indicate the potential of an ultrasonic antibiofouling method for the disruption of microbial biofilms on marine sensor housings, which is typically a principle limiting factor in their long-term operation in the oceans. With increasing deployment of scientific apparatus in aquatic environments, including further offshore

  7. Roughness Parameters Calculation By Means Of On-Line Vibration Monitoring Emerging From AWJ Interaction With Material

    Directory of Open Access Journals (Sweden)

    Hreha Pavol

    2015-06-01

    Full Text Available The paper deals with a study of relations between the measured Ra, Rq, Rz surface roughness parameters, the traverse speed of cutting head v and the vibration parameters, PtP, RMS, vRa, generated during abrasive water jet cutting of the AISI 309 stainless steel. Equations for prediction of the surface roughness parameters were derived according to the vibration parameter and the traverse speed of cutting head. Accuracy of the equations is described according to the Euclidean distances. The results are suitable for an on-line control model simulating abrasive water jet cutting and machining using an accompanying physical phenomenon for the process control which eliminates intervention of the operator.

  8. Material Properties of Various Cast Aluminum Alloys Made Using a Heated Mold Continuous Casting Technique with and without Ultrasonic Vibration

    Directory of Open Access Journals (Sweden)

    Mitsuhiro Okayasu

    2015-08-01

    Full Text Available This work was carried out to develop high-quality cast aluminum alloys using a new casting technology. For this purpose, commercial Al alloys were created by heated mold continuous casting (HMC with ultrasonic vibration (UV. With the HMC process, the grain size and the crystal orientation of the Al alloys were controlled, i.e., fine grains with a uniformly organized lattice formation. In addition, an attempt was made to modify the microstructural formation by cavitation. These microstructural characteristics made excellent mechanical properties. Using UV in the continuous casting process, more fine and spherical grains were slightly disordered, which was detected using electron backscattered diffraction. The mechanical properties of the UV HMC Al alloys were slightly higher than those for the related cast Al alloys without UV. Moreover, the severe vibration caused higher mechanical properties. The lattice and dislocation characteristics of the cast samples made with and without UV processes were analyzed systematically using electron backscattered diffraction.

  9. Chatter reduction in boring process by using piezoelectric shunt damping with experimental verification

    Science.gov (United States)

    Yigit, Ufuk; Cigeroglu, Ender; Budak, Erhan

    2017-09-01

    Chatter is a self-excited type of vibration that develops during machining due to process-structure dynamic interactions resulting in modulated chip thickness. Chatter is an important problem as it results in poor surface quality, reduced productivity and tool life. The stability of a cutting process is strongly influenced by the frequency response function (FRF) at the cutting point. In this study, the effect of piezoelectric shunt damping on chatter vibrations in a boring process is studied. In piezoelectric shunt damping method, an electrical impedance is connected to a piezoelectric transducer which is bonded on cutting tool. Electrical impedance of the circuit consisting of piezoceramic transducer and passive shunt is tuned to the desired natural frequency of the cutting tool in order to maximize damping. The optimum damping is achieved in analytical and finite element models (FEM) by using a genetic algorithm focusing on the real part of the tool point FRF rather than the amplitude. Later, a practical boring bar is considered where the optimum circuit parameters are obtained by the FEM. Afterwards, the effect of the optimized piezoelectric shunt damping on the dynamic rigidity and absolute stability limit of the cutting process are investigated experimentally by modal analysis and cutting tests. It is both theoretically and experimentally shown that application of piezoelectric shunt damping results in a significant increase in the absolute stability limit in boring operations.

  10. Wind Turbine Rotors with Active Vibration Control

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann

    This thesis presents a framework for structural modeling, analysis and active vibration damping of rotating wind turbine blades and rotors. A structural rotor model is developed in terms of finite beam elements in a rotating frame of reference. The element comprises a representation of general...... formulation. The element provides an accurate representation of the eigenfrequencies and whirling modes of the gyroscopic system, and identifies lightly damped edge-wise modes. By adoption of a method for active, collocated resonant vibration of multi-degree-of-freedom systems it is demonstrated...... that these are geometrically well separated. For active vibration control in three-bladed wind turbine rotors the present work presents a resonance-based method for groups of one collective and two whirling modes. The controller is based on the existing resonant format and introduces a dual system targeting the collective...

  11. Chatter vibrations of high-performance motorcycles

    Science.gov (United States)

    Sharp, R. S.; Watanabe, Y.

    2013-03-01

    Motorcycle racing teams occasionally experience speed-limiting vibrations of around 25 Hz frequency in mid-corner. The nature of the vibrations has not been closely defined yet and the mechanics are currently not properly understood. Conventional motorcycle-dynamics models are shown here to reveal the existence of a vibration mode that aligns with the experience being referred to, suggesting some explanations. Root loci for variations in speed or cornering vigour, demonstrating modal characteristics for small perturbations from trim states, are employed to indicate how the mode responds to changes in operation and design. Modal participation is examined for a lightly damped case. Influences on the natural frequency and damping of the mode are found and a way of stabilising the mode is suggested.

  12. Low-frequency vibration control of floating slab tracks using dynamic vibration absorbers

    Science.gov (United States)

    Zhu, Shengyang; Yang, Jizhong; Yan, Hua; Zhang, Longqing; Cai, Chengbiao

    2015-09-01

    This study aims to effectively and robustly suppress the low-frequency vibrations of floating slab tracks (FSTs) using dynamic vibration absorbers (DVAs). First, the optimal locations where the DVAs are attached are determined by modal analysis with a finite element model of the FST. Further, by identifying the equivalent mass of the concerned modes, the optimal stiffness and damping coefficient of each DVA are obtained to minimise the resonant vibration amplitudes based on fixed-point theory. Finally, a three-dimensional coupled dynamic model of a metro vehicle and the FST with the DVAs is developed based on the nonlinear Hertzian contact theory and the modified Kalker linear creep theory. The track irregularities are included and generated by means of a time-frequency transformation technique. The effect of the DVAs on the vibration absorption of the FST subjected to the vehicle dynamic loads is evaluated with the help of the insertion loss in one-third octave frequency bands. The sensitivities of the mass ratio of DVAs and the damping ratio of steel-springs under the floating slab are discussed as well, which provided engineers with the DVA's adjustable room for vibration mitigation. The numerical results show that the proposed DVAs could effectively suppress low-frequency vibrations of the FST when tuned correctly and attached properly. The insertion loss due to the attachment of DVAs increases as the mass ratio increases, whereas it decreases with the increase in the damping ratio of steel-springs.

  13. Suspended chains damp wind-induced oscillations of tall flexible structures

    Science.gov (United States)

    Reed, W. H., III

    1968-01-01

    Hanging-chain system, which is a form of impact damper, suppresses wind-induced bending oscillations of tall cylindrical antenna masts. A cluster of chains enclosed in a neoprene shroud is suspended inside the tip of the antenna mast, forming a simple method of damping structural vibrations.

  14. Comparison of complex moduli obtained from forced and free damped oscillations

    NARCIS (Netherlands)

    Heller, R.A.; Nederveen, C.J.

    1967-01-01

    While the concept of the complex modulus is based on a forced vibration experiment it is a frequent practice to perform instead a much simpler free damped oscillation test from which an approximate value of the modulus is then evaluated. The validity of this approach and the ensuing errors are

  15. Tissue vibration in prolonged running.

    Science.gov (United States)

    Friesenbichler, Bernd; Stirling, Lisa M; Federolf, Peter; Nigg, Benno M

    2011-01-04

    The impact force in heel-toe running initiates vibrations of soft-tissue compartments of the leg that are heavily dampened by muscle activity. This study investigated if the damping and frequency of these soft-tissue vibrations are affected by fatigue, which was categorized by the time into an exhaustive exercise. The hypotheses were tested that (H1) the vibration intensity of the triceps surae increases with increasing fatigue and (H2) the vibration frequency of the triceps surae decreases with increasing fatigue. Tissue vibrations of the triceps surae were measured with tri-axial accelerometers in 10 subjects during a run towards exhaustion. The frequency content was quantified with power spectra and wavelet analysis. Maxima of local vibration intensities were compared between the non-fatigued and fatigued states of all subjects. In axial (i.e. parallel to the tibia) and medio-lateral direction, most local maxima increased with fatigue (supporting the first hypothesis). In anterior-posterior direction no systematic changes were found. Vibration frequency was minimally affected by fatigue and frequency changes did not occur systematically, which requires the rejection of the second hypothesis. Relative to heel-strike, the maximum vibration intensity occurred significantly later in the fatigued condition in all three directions. With fatigue, the soft tissue of the triceps surae oscillated for an extended duration at increased vibration magnitudes, possibly due to the effects of fatigue on type II muscle fibers. Thus, the protective mechanism of muscle tuning seems to be reduced in a fatigued muscle and the risk of potential harm to the tissue may increase. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Detection of directional energy damping in vibrating systems - Indian ...

    Indian Academy of Sciences (India)

    Abstract. The transmission efficiency, frequency and amplitude alteration have been measured by a simple technique of coupled oscillators with a frequency gradient and in a system of non-Newtonian fluid in the form of corn-flour slime. The system of coupled oscillators was found to exhibit preferential energy transfer ...

  17. Cryogenic Vibration Damping Mechanisms for Space Telescopes and Interferometers Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In its mission to understand how galaxies, stars, and planetary systems form, NASA's Origins Technology Program calls for advances in "enabling component and...

  18. Detection of directional energy damping in vibrating systems

    Indian Academy of Sciences (India)

    The transmission efficiency, frequency and amplitude alteration have been measured by a simple technique of coupled oscillators with a frequency gradient and in a system of non-Newtonian fluid in the form of corn-flour slime. The system of coupled oscillators was found to exhibit preferential energy transfer towards the ...

  19. Development of a variable stiffness and damping tunable vibration isolator

    CSIR Research Space (South Africa)

    Cronje, JM

    2005-03-01

    Full Text Available the amplification at resonance. A practical variable stiffness spring was developed by using a compound leaf spring with circular spring elements. A wax actuator, controlled by a hot-air gun with a closed-loop displacement and velocity feedback control system...

  20. Vibrations and alternated stresses in turbomachineries; Vibrations et contraintes alternees dans les turbomachines

    Energy Technology Data Exchange (ETDEWEB)

    Naudin, M. [Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)]|[FRAMATOME, 92 - Paris-La-Defense (France); Pugnet, J.M. [Conservatoire National des Arts et Metiers (CNAM), Grenoble-1 Univ., 38 (France)]|[FRAMATOME, 92 - Paris-La-Defense (France)

    1999-07-01

    Vibration phenomena are sources of mechanical incidents in turbomachineries. A calculation of the Eigenmodes of machine parts and a knowledge of their possible excitation during the machine operation can greatly improve the reliability and availability of the equipments. The development of computer tools and in particular the use of finite-element codes has allowed a more and more precise calculation of Eigenmodes and Eigenfrequencies. However, the analysis of excitation sources remains sometimes insufficient to explain and anticipate some complex vibrational phenomena encountered in rotative machines. The aim of this paper is to present, using two different examples, the methodology to be used in order to perform a complete vibrational analysis of mechanical components. The following aspects are reviewed successively: 1 - the damped vibrational system: study of the free motion, study of the response to an harmonic forced excitation; 2 - vibrational analysis of turbine blades: steam turbine blades, Eigenmodes of mobile blades, excitation sources, Campbell diagram, calculation of static and dynamical stresses, Haigh diagram, acceptance criteria and safety coefficient, influence of corrosion; 3 - dynamical analysis of the bending of a lineshaft: different flexion Eigenmodes, stiffness and damping of bearings, calculation of flexion Eigenmodes, excitation sources, vibrational stability of the lineshaft and vibration level; 3 - generalization: vibration of blades, shaft dynamics, alternative machines. (J.S.) 10 refs.

  1. Dampness in buildings and health

    DEFF Research Database (Denmark)

    Bornehag, Carl-Gustaf; Blomquist, G.; Gyntelberg, F.

    2001-01-01

    Several epidemiological investigations concerning indoor environments have indicated that "dampness" in buildings is associated to health effects such as respiratory symptoms, asthma and allergy The aim of the present interdisciplinary review is to evaluate this association as shown in the epidem......Several epidemiological investigations concerning indoor environments have indicated that "dampness" in buildings is associated to health effects such as respiratory symptoms, asthma and allergy The aim of the present interdisciplinary review is to evaluate this association as shown...... in the epidemiological literature. A literature search identified 590 peer-reviewed articles of which 61 have been the foundation for this review. The review shows that "dampness" in buildings appears to increase the risk for health effects in the airways, such as cough, wheeze and asthma. Relative risks...... are in the range of OR 1.4-2.2. There also seems to be an association between "dampness" and other symptoms Such as tiredness, headache and airways infections. It is concluded that the evidence for a causal association between "dampness" and health effects is strong. However, the mechanisms are unknown. Several...

  2. Damping mechanisms of a pendulum

    Science.gov (United States)

    Dolfo, Gilles; Castex, Daniel; Vigué, Jacques

    2016-11-01

    In this paper, we study the damping mechanisms of a pendulum. The originality of our setup is the use of a metal strip suspension and the development of extremely sensitive electric measurements of the pendulum velocity and position. Their sensitivity is absolutely necessary for a reliable measurement of the pendulum damping time constant because this measurement is possible only for very low oscillation amplitudes, when air friction forces quadratic in velocity have a negligible contribution to the observed damping. We have thus carefully studied damping by air friction forces, which is the dominant mechanism for large values of the Reynolds number Re but which is negligible in the Stokes regime, {Re} ∼ 1. In this last case, we have found that the dominant damping is due to internal friction in the metal strip, a universal effect called anelasticity, and, for certain frequencies, to resonant coupling to the support of the pendulum. All our measurements are well explained by theory. We believe this paper would be of interest to students in an undergraduate classical mechanics course.

  3. Finite element modelling for the investigation of in-plane modes and damping shims in disc brake squeal

    Science.gov (United States)

    Kang, Jaeyoung

    2012-04-01

    Squeal propensity of the in-plane modes and the constrained-layer type damping shims for disc brake system is investigated by using the finite element method. Theoretical formulation is derived for a rotating disc in contact with two stationary vibrating pads attached to the damping shim components. By the conversion from the theoretical to FE brake model, the full equations of motion for the actual disc brake system describes the disc rotation, the in-plane friction characteristics and damping shims in association with squeal vibration. It is concluded from the results that the in-plane torsion modes can be generated by the negative friction slope, but they cannot be controlled by the damping shims. The in-plane radial mode is also investigated and found to be very insensitive in squeal generation.

  4. High force vibration testing with wide frequency range

    Science.gov (United States)

    Romero, Edward F.; Jepsen, Richard A.; Gregory, Danny Lynn

    2013-04-02

    A shaker assembly for vibration testing includes first and second shakers, where the first shaker includes a piezo-electric material for generating vibration. A support structure permits a test object to be supported for vibration of the test object by both shakers. An input permits an external vibration controller to control vibration of the shakers.

  5. Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 1: Verification of basic methods

    Science.gov (United States)

    Chiang, T.; Tessarzik, J. M.; Badgley, R. H.

    1972-01-01

    The primary aim of this investigation was verification of basic methods which are to be used in cataloging elastomer dynamic properties (stiffness and damping) in terms of viscoelastic model constants. These constants may then be used to predict dynamic properties for general elastomer shapes and operating conditions, thereby permitting optimum application of elastomers as energy absorption and/or energy storage devices in the control of vibrations in a broad variety of applications. The efforts reported involved: (1) literature search; (2) the design, fabrication and use of a test rig for obtaining elastomer dynamic test data over a wide range of frequencies, amplitudes, and preloads; and (3) the reduction of the test data, by means of a selected three-element elastomer model and specialized curve fitting techniques, to material properties. Material constants thus obtained have been used to calculate stiffness and damping for comparison with measured test data. These comparisons are excellent for a number of test conditions and only fair to poor for others. The results confirm the validity of the basic approach of the overall program and the mechanics of the cataloging procedure, and at the same time suggest areas in which refinements should be made.

  6. Piezoelectric Tailoring with Enhanced Electromechanical Coupling for Concurrent Vibration Control of Mistuned Periodic Structures

    National Research Council Canada - National Science Library

    Wang, Kon-Well

    2006-01-01

    The objective of this research is to advance the state of the art of vibration control of mistuned periodic structures utilizing the electromechanical coupling and damping characteristics of piezoelectric networking...

  7. Radiation damping in ferromagnetic resonance induced by a conducting spin sink

    Science.gov (United States)

    Qaid, Mohammad M.; Richter, Tim; Müller, Alexander; Hauser, Christoph; Ballani, Camillo; Schmidt, Georg

    2017-11-01

    We have investigated the damping in the ferromagnetic resonance (FMR) of yttrium iron garnet (YIG) caused by spin pumping into adjacent conducting materials, namely, Pt and the conducting polymer poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS). By a systematic study which also includes multilayers in which the conducting layer is separated from YIG by an insulator, we can show that a considerable part of the damping can be attributed to the so-called radiation damping which originates from the interaction of the magnetic fields caused by the precessing magnetization with the conducting layer. Especially, when PEDOT:PSS is used as a spin sink, the observed damping must be attributed completely to radiation damping, and no contribution from spin pumping can be identified. These results demonstrate that the Gilbert damping as a measure of spin pumping can only be used when careful control experiments accompany the investigation.

  8. Steps for Vibration Reduction of 50kg-Class Micro-Satellite Structure

    Science.gov (United States)

    Nakamura, Masato; Furukawa, Takuya; Chiba, Masakatsu; Okubo, Hiroshi; Akita, Takeshi; Sugiyama, Yoshihiko; Nakamura, Yosuke; Imamura, Hiroaki; Umehara, Nobuhito

    The paper reports several steps taken to reduce vibration responses of a 50kg-class micro-satellite structure, which is subjected to severe mechanical/vibratory environment during launching. In order to satisfy the required mechanical interface conditions, anti-vibration design of satellite structure was modified to enhance damping capacity of the structure by applying adherent aisogrid-panel, honeycomb panel, polyimid-tape-inserted connections, and damping pads. Considerable reduction of vibration responses was confirmed by vibration test of structural-thermal model.

  9. Characterization of hydrofoil damping due to fluid-structure interaction using piezocomposite actuators

    Science.gov (United States)

    Seeley, Charles; Coutu, André; Monette, Christine; Nennemann, Bernd; Marmont, Hugues

    2012-03-01

    Hydroelectric power generation is an important non-fossil fuel power source to help meet the world’s energy needs. Fluid-structure interaction (FSI), in the form of mass loading and damping, governs the dynamic response of water turbines, such as Francis turbines. Although the effects of fluid mass loading are well documented, fluid damping is also a critical quantity that may limit vibration amplitudes during service, and therefore help to avoid premature failure of the turbines. However, fluid damping has received less attention in the literature. This paper presents an experimental investigation of damping due to FSI. Three hydrofoils were designed and built to investigate damping due to FSI. Piezoelectric actuation using macrofiber composites (MFCs) provided excitation to the hydrofoil test structure, independent of the flow conditions, to overcome the noisy environment. Natural frequency and damping estimates were experimentally obtained from sine sweep frequency response functions measured with a laser vibrometer through a window in the test section. The results indicate that, although the natural frequencies were not substantially affected by the flow, the damping ratios were observed to increase in a linear manner with respect to flow velocity.

  10. Characterization of Fibre-Direction Dependent Damping of Glass-Fibre Composites at Low Temperatures and Low Frequencies

    DEFF Research Database (Denmark)

    Kliem, Mathias; Høgsberg, Jan Becker; Dannemann, Martin

    2016-01-01

    a Dynamic Mechanical Analysis (DMA) for five different fibre orientations (0˚ | 30˚ | 45˚ | 60˚ and 90˚) and two different matrix systems (epoxy and a vinyl ester resin). Based on the dynamic characteristics the damping performance of the various composite materials was studied at three temperatures (-10˚C......, 0˚C and 10˚C) and three vibration frequencies (1 Hz, 10 Hz and 30 Hz). It was observed that the loss factor of Glass Fibre Reinforced Vinyl-Ester (GF-VE) was in general slightly higher compared to the Glass Fibre Reinforced Epoxy (GF-EP). The loss factor increased slightly with temperature, while...

  11. The Shock and Vibration Digest. Volume 14, Number 10

    Science.gov (United States)

    1982-10-01

    Polyurethane Foams ," J. Cell. Plast., 14 (2) (Mar-Apr 1978). 17. Aubrey, D.W. and Sherriff, M., " Viscoelasticity of Rubber-Resin Mixtures," J. Poly...elastomers subjected to static deformations was investigated [15]. Dynamic stiffness and damping data were given for Polyurethane foams used for sound...19. Wong, D.T.H. and Williams, H.L., "Vibration Damping Properties of Polyurethanes ; Dynamic Properties of the Viscoelastic Layers," lnt|. Symp

  12. Accounting for Film-Forming and Damping Properties of Lubricants in Worm Gear Design

    Directory of Open Access Journals (Sweden)

    S. A. Polyakov

    2014-01-01

    Full Text Available The paper offers to use a curve of changing vibration amplitude of the rotating moment on the worm shaft of reducer in the process of growing brake (loading moment as one of criteria of the worm reducer operability. A condition of reducer operability at the nominal moment is lack of vibrations of the rotating moment with a critical value of amplitude.It is shown that vibrations of rotating moment on a shaft of the electric engine, by their nature, are self-vibrations in the system with "negative friction". Values of the brake moment at which there is a sharp increase of vibration amplitude leading to operability loss correspond to the nominal moment for this reducer or to the brake moment, corresponding to the maximum efficiency. It is shown that different lubricants differently influence on the generation of self-vibrations. The most efficient damping occurs when using oil with the additive "Striboil", and the reason of falling efficiency at the excess of the nominal moment is essentially increased energy losses at generation of vibrations with "negative friction", especially when approaching to the resonance area. Thus, taking into account a nature of damping vibrations, with using different lubricants, allows us to increase the permissible tension since the more is a damping value the more is a brake moment corresponding to the maximum efficiency. It is noted that, when using the additives to oils, a growth of the permissible tension is caused by the processes of film formation increasing the real contact area, which increases its share of the nominal contact area determined by the Hertz formula.

  13. Increased magnetic damping of a single domain wall and adjacent magnetic domains detected by spin torque diode in a nanostripe

    Energy Technology Data Exchange (ETDEWEB)

    Lequeux, Steven; Sampaio, Joao; Bortolotti, Paolo; Cros, Vincent; Grollier, Julie [Unité Mixte de Physique CNRS/Thales and Université Paris-Sud 11, 1 Ave. A. Fresnel, 91767 Palaiseau (France); Devolder, Thibaut [Institut d' Electronique Fondamentale, Univ. Paris-Sud, CNRS UMR 8622, Bât. 220, 91405 Orsay Cedex (France); Matsumoto, Rie; Yakushiji, Kay; Kubota, Hitoshi; Fukushima, Akio; Yuasa, Shinji [National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan); Nishimura, Kazumasa; Nagamine, Yoshinori; Tsunekawa, Koji [Process Development Center, Canon ANELVA Corporation, Kurigi 2-5-1, Asao, Kawasaki, Kanagawa 215-8550 (Japan)

    2015-11-02

    Spin torque resonance has been used to simultaneously probe the dynamics of a magnetic domain wall and of magnetic domains in a nanostripe magnetic tunnel junction. Due to the large associated resistance variations, we are able to analyze quantitatively the resonant properties of these single nanoscale magnetic objects. In particular, we find that the magnetic damping of both the domains and the domain wall is doubled compared to the damping value of the host magnetic layer. We estimate the contributions to the damping arising from the dipolar couplings between the different layers in the junction and from the intralayer spin pumping effect, and find that they cannot explain the large damping enhancement that we observe. We conclude that the measured increased damping is intrinsic to large amplitudes excitations of spatially localized modes or solitons such as vibrating or propagating domain walls.

  14. Guy cable design and damping for vertical axis wind turbines

    Science.gov (United States)

    Carne, T. G.

    1981-01-01

    Guy cables are frequently used to support vertical axis wind turbines since guying the turbine reduces some of the structural requirements on the tower. The guys must be designed to provide both the required strength and the required stiffness at the top of the turbine. The axial load which the guys apply to the tower, bearings, and foundations is an undesirable consequence of using guys to support the turbine. Limiting the axial load so that it does not significantly affect the cost of the turbine is an important objective of the cable design. The lateral vibrations of the cables is another feature of the cable design which needs to be considered. These aspects of the cable design are discussed, and a technique for damping cable vibrations was mathematically analyzed and demonstrated with experimental data.

  15. Red cell DAMPs and inflammation.

    Science.gov (United States)

    Mendonça, Rafaela; Silveira, Angélica A A; Conran, Nicola

    2016-09-01

    Intravascular hemolysis, or the destruction of red blood cells in the circulation, can occur in numerous diseases, including the acquired hemolytic anemias, sickle cell disease and β-thalassemia, as well as during some transfusion reactions, preeclampsia and infections, such as those caused by malaria or Clostridium perfringens. Hemolysis results in the release of large quantities of red cell damage-associated molecular patterns (DAMPs) into the circulation, which, if not neutralized by innate protective mechanisms, have the potential to activate multiple inflammatory pathways. One of the major red cell DAMPs, heme, is able to activate converging inflammatory pathways, such as toll-like receptor signaling, neutrophil extracellular trap formation and inflammasome formation, suggesting that this DAMP both activates and amplifies inflammation. Other potent DAMPs that may be released by the erythrocytes upon their rupture include heat shock proteins (Hsp), such as Hsp70, interleukin-33 and Adenosine 5' triphosphate. As such, hemolysis represents a major inflammatory mechanism that potentially contributes to the clinical manifestations that have been associated with the hemolytic diseases, such as pulmonary hypertension and leg ulcers, and likely plays a role in specific complications of sickle cell disease such as endothelial activation, vaso-occlusive processes and tissue injury.

  16. On the effect of damping on dispersion curves in plates

    DEFF Research Database (Denmark)

    Manconia, Elisabetta; Sorokin, Sergey

    2013-01-01

    This paper presents a study on quantitative prediction and understanding of time-harmonic wave characteristics in damped plates. Material dissipation is modelled by using complex-valued velocities of free dilatation and shear waves in an unbounded volume. As a numerical example, solution...

  17. Next generation HOM-damping

    Science.gov (United States)

    Marhauser, Frank

    2017-06-01

    Research and development for superconducting radio-frequency cavities has made enormous progress over the last decades from the understanding of theoretical limitations to the industrial mass fabrication of cavities for large-scale particle accelerators. Key technologies remain hot topics due to continuously growing demands on cavity performance, particularly when in pursuit of high quality beams at higher beam currents or higher luminosities than currently achievable. This relates to higher order mode (HOM) damping requirements. Meeting the desired beam properties implies avoiding coupled multi-bunch or beam break-up instabilities depending on the machine and beam parameters that will set the acceptable cavity impedance thresholds. The use of cavity HOM-dampers is crucial to absorb the wakefields, comprised by all beam-induced cavity Eigenmodes, to beam-dynamically safe levels and to reduce the heat load at cryogenic temperature. Cavity damping concepts may vary, but are principally based on coaxial and waveguide couplers as well as beam line absorbers or any combination. Next generation energy recovery linacs and circular colliders call for cavities with strong HOM-damping that can exceed the state-of-the-art, while the operating mode efficiency shall not be significantly compromised concurrently. This imposes major challenges given the rather limited damping concepts. A detailed survey of established cavities is provided scrutinizing the achieved damping performance, shortcomings, and potential improvements. The scaling of the highest passband mode impedances is numerically evaluated in dependence on the number of cells for a single-cell up to a nine-cell cavity, which reveals the increased probability of trapped modes. This is followed by simulations for single-cell and five-cell cavities, which incorporate multiple damping schemes to assess the most efficient concepts. The usage and viability of on-cell dampers is elucidated for the single-cell cavity since it

  18. Factors affecting the perception of whole-body vibration of occupational drivers: an analysis of posture and manual materials handling and musculoskeletal disorders.

    Science.gov (United States)

    Raffler, Nastaran; Ellegast, Rolf; Kraus, Thomas; Ochsmann, Elke

    2016-01-01

    Due to the high cost of conducting field measurements, questionnaires are usually preferred for the assessment of physical workloads and musculoskeletal disorders (MSDs). This study compares the physical workloads of whole-body vibration (WBV) and awkward postures by direct field measurements and self-reported data of 45 occupational drivers. Manual materials handling (MMH) and MSDs were also investigated to analyse their effect on drivers' perception. Although the measured values for WBV exposure were very similarly distributed among the drivers, the subjects' perception differed significantly. Concerning posture, subjects seemed to estimate much better when the difference in exposure was significantly large. The percentage of measured awkward trunk and head inclination were significantly higher for WBV-overestimating subjects than non-overestimators; 77 and 80% vs. 36 and 33%. Health complaints in terms of thoracic spine, cervical spine and shoulder-arm were also significantly more reported by WBV-overestimating subjects (42, 67, 50% vs. 0, 25, 13%, respectively). Although more MMH was reported by WBV-overestimating subjects, there was no statistical significance in this study. Self-reported exposures of occupational drivers are affected by many other cofactors, and this can result in misinterpretations. A comparison between field measurement and questionnaire was used to highlight the factors affecting the perception of drivers for whole-body vibration (WBV) exposure. Posture and musculoskeletal disorders influenced the perception of the similarly WBV-exposed drivers significantly.

  19. Vibration modeling of structural fuzzy with continuous boundary

    DEFF Research Database (Denmark)

    Friis, Lars; Ohlrich, Mogens

    2008-01-01

    From experiments it is well known that the vibration response of a main structure with many attached substructures often shows more damping than structural losses in the components can account for. In practice, these substructures, which are not attached in an entirely rigid manner, behave like...... effect of the fuzzy with spatial memory is demonstrated by numerical simulations of a main beam structure with fuzzy attachments. It is shown that the introduction of spatial memory reduces the damping effect of the fuzzy and in certain cases the damping effect may even be eliminated completely....

  20. On strain-rate independent damping in continuum mechanics

    Science.gov (United States)

    Mulder, Gerben

    2017-10-01

    Strain-rate independent damping is a theory of energy dissipation in solids. It is based on the assumption that an increase or decrease in the strain-energy density correlates with a multiplication of 1+η or 1-η respectively, of the material stiffness matrix, with 0≤ η derived for strain-rate independent damping can be solved for 1, 2 or 3 dimensions via direct integration, provided that the software supports PDE coefficients that are functions of the solution and its space and time derivatives. A 3D problem with 22,000 DOF's and 10,000 time steps was solved successfully and convincingly.

  1. Damping of gravitational waves by matter

    Science.gov (United States)

    Baym, Gordon; Patil, Subodh P.; Pethick, C. J.

    2017-10-01

    We develop a unified description, via the Boltzmann equation, of damping of gravitational waves by matter, incorporating collisions. We identify two physically distinct damping mechanisms—collisional and Landau damping. We first consider damping in flat spacetime, and then generalize the results to allow for cosmological expansion. In the first regime, maximal collisional damping of a gravitational wave, independent of the details of the collisions in the matter is, as we show, significant only when its wavelength is comparable to the size of the horizon. Thus damping by intergalactic or interstellar matter for all but primordial gravitational radiation can be neglected. Although collisions in matter lead to a shear viscosity, they also act to erase anisotropic stresses, thus suppressing the damping of gravitational waves. Damping of primordial gravitational waves remains possible. We generalize Weinberg's calculation of gravitational wave damping, now including collisions and particles of finite mass, and interpret the collisionless limit in terms of Landau damping. While Landau damping of gravitational waves cannot occur in flat spacetime, the expansion of the universe allows such damping by spreading the frequency of a gravitational wave of given wave vector.

  2. Roll Damping Characterisation Program: User Guide

    Science.gov (United States)

    2014-06-01

    Cubic roll damping coefficient blin Linear roll damping coefficient bqua Quadratic roll damping coefficient Cxx Roll restoring moment coefficient g...testing conducted on a 32 bit Hewlett Packard desktop personal computer the RDCP was observed to function satisfactorily, however, the processing of

  3. Fatigue and soft tissue vibration during prolonged running.

    Science.gov (United States)

    Khassetarash, Arash; Hassannejad, Reza; Ettefagh, Mir Mohammad; Sari-Sarraf, Vahid

    2015-12-01

    Muscle tuning paradigm proposes that the mechanical properties of soft tissues are tuned in such a way that its vibration amplitude become minimized. Therefore, the vibrations of soft tissue are heavily damped. However, it has been hypothesized that the ability of muscle tuning decreases with fatigue. This study investigated the changes in vibration characteristics of soft tissue with fatigue. Vibrations of the gastrocnemius muscle of 8 runners during a prolonged run protocol on a treadmill at constant velocity (4 ms(-1)) were measured using a tri-axial accelerometer. The vibration amplitude is calculated using the Fourier transform and a wavelet-based method was used to calculate the damping coefficient. The results showed that: (1) the vibration amplitude in longitudinal direction increased with fatigue, which may be interpreted as the decreased muscle function with fatigue. (2) The amplitude increase percent strongly depended on the vibration frequency. (3) The damping coefficient of the gastrocnemius increased with fatigue. A 1-DOF mass-spring-damper model was used in order to validate the wavelet based method and simulate the observed phenomena. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Striplines for CLIC Pre-damping and Damping Rings

    CERN Document Server

    Belver-Aguilar, C; Barnes, M J; Rumolo, G; Zannini, C; Toral, F

    2011-01-01

    The Compact Linear Collider (CLIC) study explores the scheme for an electron-positron collider with high luminosity and a nominal centre-of-mass energy of 3 TeV: CLIC will complement LHC physics in the multi-TeV range. The CLIC design relies on the presence of Pre-Damping Rings (PDR) and Damping Rings (DR) to achieve, through synchrotron radiation, the very low emittance needed to fulfill the luminosity requirements. The specifications for the kicker systems are very challenging and include very low beam coupling impedance and excellent field homogeneity: striplines have been chosen for the kicker elements. Analytical calculations have been carried out to determine the effect of tapering upon the high frequency beam coupling impedance. In addition detailed numerical modeling of the field homogeneity has been performed and the sensitivity of the homogeneity to various parameters, including stripline cross-section, have been studied. This paper presents the main conclusions of the beam impedance calculations an...

  5. Unimodal optimal passive electromechanical damping of elastic structures

    Science.gov (United States)

    Ben Mekki, O.; Bourquin, F.; Maceri, F.; Merliot, E.

    2013-08-01

    In this paper, a new electromechanical damper is presented and used, made of a pendulum oscillating around an alternator axis and connected by a gear to the vibrating structure. In this way, the mechanical energy of the oscillating mass can be transformed into electrical energy to be dissipated when the alternator is branched on a resistor. This damping device is intrinsically non-linear, and the problem of the optimal parameters and of the best placement of this damper on the structure is studied. The optimality criterion chosen here is the maximum exponential time decay rate (ETDR) of the structural response. This criterion leads to new design formulas. The case of a bridge under construction is considered and the analytical results are compared with experimental ones, obtained on a mock-up made of a vertical tower connected to a free-end horizontal beam, to simulate the behavior of a cable-stayed bridge during the erection phase. Up to three electromechanical dampers are placed in order to study the multi-modal damping. The satisfactory agreement between the theoretical model and the experiments suggests that a multi-modal passive damping of electromagnetic type could be effective on lightweight flexible structures, when dampers are suitably placed.

  6. Seismic damage diagnosis of a masonry building using short-term damping measurements

    Science.gov (United States)

    Kouris, Leonidas Alexandros S.; Penna, Andrea; Magenes, Guido

    2017-04-01

    It is of considerable importance to perform dynamic identification and detect damage in existing structures. This paper describes a new and practical method for damage diagnosis of masonry buildings requiring minimum computational effort. The method is based on the relative variation of modal damping and validated against experimental data from a full scale two storey shake table test. The experiment involves a building subjected to uniaxial vibrations of progressively increasing intensity at the facilities of EUCENTRE laboratory (Pavia, Italy) up to a near collapse damage state. Five time-histories are applied scaling the Montenegro (1979) accelerogram. These strong motion tests are preceded by random vibration tests (RVT's) which are used to perform modal analysis. Two deterministic methods are applied: the single degree of freedom (SDOF) assumption together with the peak-picking method in the discrete frequency domain and the Eigen realisation algorithm with data correlations (ERA-DC) in the discrete time domain. Regarding the former procedure, some improvements are incorporated to locate rigorously the natural frequencies and estimate the modal damping. The progressive evolution of the modal damping is used as a key indicator to characterise damage on the building. Modal damping is connected to the structural mass and stiffness. A square integrated but only with two components expression for proportional (classical) damping is proposed to fit better with the experimental measurements of modal damping ratios. Using this Rayleigh order formulation the contribution of each of the damping components is evaluated. The stiffness component coefficient is proposed as an effective index to detect damage and quantify its intensity.

  7. Application of a high-performance damping metal to gravitational wave detectors

    CERN Document Server

    Mio, N; Moriwaki, S

    2002-01-01

    We have investigated applications of a high-performance damping metal, called M2052, which is a manganese-based alloy containing copper, nickel and iron. Using an all-metal prototype of a vibration isolation system, we have tested the property of M2052. As its actual application to a gravitational wave detector, we have used M2052 in the damping system of a suspended optics in TAMA300, which is a 300 m long interferometric gravitational wave detector built at the Mitaka campus of the National Astronomical Observatory in Japan. The results of the experiments are reported.

  8. Finite-Element Vibration Analysis and Modal Testing of Graphite Epoxy Tubes and Correlation Between the Data

    Science.gov (United States)

    Taleghani, Barmac K.; Pappa, Richard S.

    1996-01-01

    Structural materials in the form of graphite epoxy composites with embedded rubber layers are being used to reduce vibrations in rocket motor tubes. Four filament-wound, graphite epoxy tubes were studied to evaluate the effects of the rubber layer on the modal parameters (natural vibration frequencies, damping, and mode shapes). Tube 1 contained six alternating layers of 30-degree helical wraps and 90-degree hoop wraps. Tube 2 was identical to tube 1 with the addition of an embedded 0.030-inch-thick rubber layer. Tubes 3 and 4 were identical to tubes 1 and 2, respectively, with the addition of a Textron Kelpoxy elastomer. This report compares experimental modal parameters obtained by impact testing with analytical modal parameters obtained by NASTRAN finite-element analysis. Four test modes of tube 1 and five test modes of tube 3 correlate highly with corresponding analytical predictions. Unsatisfactory correlation of test and analysis results occurred for tubes 2 and 4 and these comparisons are not shown. Work is underway to improve the analytical models of these tubes. Test results clearly show that the embedded rubber layers significantly increase structural modal damping as well as decrease natural vibration frequencies.

  9. Monitoring vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Tiryaki, B. [Hacettepe University (Turkey). Dept. of Mining Engineering

    2003-12-01

    The paper examines the prediction and optimisation of machine vibrations in longwall shearers. Underground studies were carried out at the Middle Anatolian Lignite Mine, between 1993 and 1997. Several shearer drums with different pick lacing arrangements were designed and tested on double-ended ranging longwall shearers employed at the mine. A computer program called the Vibration Analysis Program (VAP) was developed for analysing machine vibrations in longwall shearers. Shearer drums that were tested underground, as well as some provided by leading manufacturers, were analyzed using these programs. The results of the experiments and computer analyses are given in the article. 4 refs., 9 figs.

  10. Evaluation of damping property of long-span prestressed concrete cable-stayed bridges; Chodai PC shachokyo no gensui tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamanobe, S.; Niihara, Y.; Minami, H.; Kono, T. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    As to the dynamic design in the antiseismic design of PC cable-stayed bridges, evaluation of damping is important. Since it is difficult to evaluate damping property theoretically and analytically, a lot of studies have not been made about how to set up damping coefficients. In this study, using analytical models of existing long-span PC cable-stayed bridges, to clarify causes of damping of long-span PC cable-stayed bridge, the rate of strain energy in each member was examined. Equivalent damping coefficients of each member, effects of friction in movable bearing, and effects of basically radiational damping were studied. The correspondence with the results of the vibration experiments conventionally made were studied. (translated by NEDO)

  11. Crystal growth, vibrational, optical, thermal and theoretical studies of a nonlinear optical material: 2-Methyl 3,5-dinitrobenzoic acid

    Energy Technology Data Exchange (ETDEWEB)

    Sangeetha, K. [Department of Physics, Sri Sarada College for Women, Salem-16 (India); Guru Prasad, L. [Department of Science & Humanities, M. Kumarasamy College of Engineering, Karur (India); Mathammal, R. [Department of Physics, Sri Sarada College for Women, Salem-16 (India)

    2016-11-15

    Single crystals of 2-methyl 3,5-dinitro benzoic acid with reasonable size have been grown by slow evaporation solution growth method using ethanol as solvent. Quantum chemical calculation of 2-methyl 3,5-Dinitro benzoic acid was carried out by using DFT/B3LYP/6-31+G(d,p) method. The powder X-ray diffraction pattern was recorded and indexed. Both the experimental and theoretical vibrational spectrum validates the presence of functional groups. Polarizability, first order hyperpolarizability and the electric dipole moment values have been computed theoretically. The {sup 1}H and {sup 13}C NMR chemical shift of the molecule was calculated and compared with experimental results. TG/DSC analysis has been employed to understand the thermal and physio-chemical stability of the title compound. Frequency conversion property of the crystal was tested by Kurtz and Perry method. Optical absorption behavior of the grown crystal was examined by recording the optical spectrum and band gap energy was also estimated. The calculated HOMO and LUMO energy shows the charge transfer nature of the molecule.

  12. Vibration Isolation Technology (VIT) ATD Project

    Science.gov (United States)

    Lubomski, Joseph F.; Grodsinsky, Carlos M.; Logsdon, Kirk A.; Rohn, Douglas A.; Ramachandran, N.

    1994-01-01

    A fundamental advantage for performing material processing and fluid physics experiments in an orbital environment is the reduction in gravity driven phenomena. However, experience with manned spacecraft such as the Space Transportation System (STS) has demonstrated a dynamic acceleration environment far from being characterized as a 'microgravity' platform. Vibrations and transient disturbances from crew motions, thruster firings, rotating machinery etc. can have detrimental effects on many proposed microgravity science experiments. These same disturbances are also to be expected on the future space station. The Microgravity Science and Applications Division (MSAD) of the Office of Life and Microgravity Sciences and Applications (OLMSA), NASA Headquarters recognized the need for addressing this fundamental issue. As a result an Advanced Technology Development (ATD) project was initiated in the area of Vibration Isolation Technology (VIT) to develop methodologies for meeting future microgravity science needs. The objective of the Vibration Isolation Technology ATD project was to provide technology for the isolation of microgravity science experiments by developing methods to maintain a predictable, well defined, well characterized, and reproducible low-gravity environment, consistent with the needs of the microgravity science community. Included implicitly in this objective was the goal of advising the science community and hardware developers of the fundamental need to address the importance of maintaining, and how to maintain, a microgravity environment. This document will summarize the accomplishments of the VIT ATD which is now completed. There were three specific thrusts involved in the ATD effort. An analytical effort was performed at the Marshall Space Flight Center to define the sensitivity of selected experiments to residual and dynamic accelerations. This effort was redirected about half way through the ATD focusing specifically on the sensitivity of

  13. Verifying with tests the improved dynamic and passive damping behavior of components: structural optimization based on bionic principles

    Science.gov (United States)

    Weiss, Johannes; Maier, Martin; Herrmann, Hans-Georg; Steibler, Philipp

    2004-07-01

    In the automotive industry, the need for affordable lightweight structures rises as new fuel consumption regulations tighten and customers demand for performance increases. One way of achieving a cost-effective and weight-optimal design is by means of structural optimization. In 1991, A. Baumgartner, S. Burkhardt and C. Mattheck published their first paper on topology optimization based on bionic principles. Nature is inevitably dependent on the most efficient use of the body's mass. Using a fully-stressed-method, the original SKO-method is able to optimize engineering components with regard to maximum strength and stiffness. For several years now, the SKO-method has been successfully applied and enhanced for complex structural optimization at the Research & Technology Division of DaimlerChrysler AG. The subject presented in this paper was investigated in cooperation with the Institut fur Verbundwerkstoffe GmbH at the Technical University of Kaiserslautern. The aim is to present the new developments concerning the SKO-method. Starting with a short introduction to the original SKO-method, the newly implemented FreedOpt (Frequency and Damping Optimization) module is explained afterwards. FreedOpt can tune natural frequencies to a desired level. In cases were the tuning of frequencies is not sufficient, damping is needed. The new module is able to optimize the utilization of damping material with a new approach based on maximizing the dissipated vibration energy. The main focus of the paper is on the verification of the simulation results with physical tests. Finally, the new tool is applied to automotive parts. Concluding, the authors give an outlook for future work.

  14. Robust Rudder Roll Damping Control

    DEFF Research Database (Denmark)

    Yang, C.

    -infinity theory is used to deal with the problem. The necessary mathematical tools and the H-Infinity theory as the basis of controller design are presented in Chapter 2 and 3. The mu synthesis and the D-K iteration are introduced in Chapter 3. The ship dynamics and modeling technology are discussed in Chapter 4......The results of a systematic research to solve a specific ship motion control problem, simultaneous roll damping and course keeping using the rudder are presented in this thesis. The fundamental knowledge a priori is that rudder roll damping is highly sensitive to the model uncertainty, therefore H......, two kinds of ship model have been obtained: linear ship model used for designing the controller and nonlinear model used for simulation. The ship model uncertainty is discussed in this chapter and so is a wave model because the ship's roll motion is caused by waves. Using an unstructured model...

  15. Resonant vibration control of wind turbine blades

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann; Krenk, Steen; Høgsberg, Jan Becker

    2010-01-01

    The paper deals with introduction of damping to specific vibration modes of wind turbine blades, using a resonant controller with acceleration feedback. The wind turbine blade is represented by three-dimensional, two-node finite elements in a local, rotating frame of reference. The element....... The efficiency of the resonant controller is demonstrated for a representative turbine blade exposed to turbulent wind loading. It is found that the present explicit tuning procedure yields close to optimal tuning, with very limited modal spill-over and effective reduction of the vibration amplitudes....

  16. Optical Measurement of Cable and String Vibration

    Directory of Open Access Journals (Sweden)

    Y. Achkire

    1998-01-01

    Full Text Available This paper describes a non contacting measurement technique for the transverse vibration of small cables and strings using an analog position sensing detector. On the one hand, the sensor is used to monitor the cable vibrations of a small scale mock-up of a cable structure in order to validate the nonlinear cable dynamics model. On the other hand, the optical sensor is used to evaluate the performance of an active tendon control algorithm with guaranteed stability properties. It is demonstrated experimentally, that a force feedback control law based on a collocated force sensor measuring the tension in the cable is feasible and provides active damping in the cable.

  17. Damping Effects in Aerospace Structures

    Science.gov (United States)

    1979-10-01

    dapeadeat «a the applied damping values. Incorrect daoping values m^ lead to an inpropcr desigo. CoUeetioB and evaluation of available wmavanA...23) (24) Ref. [36] n b^ rr a Z , r rk (a Z ^ s rk arV < E rk u b r rr (25) where: y is the oodal daoping factor t> /2üI and e is a

  18. The peak response distributions of structure-DVA systems with nonlinear damping

    Science.gov (United States)

    Love, J. S.; Tait, M. J.

    2015-07-01

    Dynamic vibration absorbers (DVAs) with nonlinear damping are often modelled using a power-law equivalent viscous damping relationship. There is currently not a method available to predict the peak response of this type of nonlinear DVA without resorting to computationally expensive nonlinear simulations. Since the peak response of the DVA is required during the design process, it is advantageous to have a simplified method to estimate the peak response. In this study, statistical linearization is employed to represent the nonlinear damping as amplitude-dependent viscous damping and predict the rms response of the structure-DVA system. Subsequently, statistical nonlinearization is used to describe the probability density function of the DVA response amplitude. A probability density function is developed, which enables the peak response expected during an interval of time (e.g. 1-h) to be estimated from the rms response of the structure-DVA system. Higher power-law damping exponents are shown to result in smaller peak factors. Results of nonlinear simulations reveal that the model can estimate the peak structural and DVA responses with acceptable accuracy. A plot is developed to show the peak factors for nonlinear DVAs as a function of the number of system cycles for several power-law damping exponents. This plot can be used to estimate the peak response of a nonlinear DVA as a function of its rms response.

  19. Human-in-the-loop evaluation of RMS Active Damping Augmentation

    Science.gov (United States)

    Demeo, Martha E.; Gilbert, Michael G.; Scott, Michael A.; Lepanto, Janet A.; Bains, Elizabeth M.; Jensen, Mary C.

    1993-01-01

    Active Damping Augmentation is the insertion of Controls-Structures Integration Technology to benefit the on-orbit performance of the Space Shuttle Remote Manipulator System. The goal is to reduce the vibration decay time of the Remote Manipulator System following normal payload maneuvers and operations. Simulation of Active Damping Augmentation was conducted in the realtime human-in-the-loop Systems Engineering Simulator at the NASA Johnson Space Center. The objective of this study was to obtain a qualitative measure of operational performance improvement from astronaut operators and to obtain supporting quantitative performance data. Sensing of vibratory motions was simulated using a three-axis accelerometer mounted at the end of the lower boom of the Remote Manipulator System. The sensed motions were used in a feedback control law to generate commands to the joint servo mechanisms which reduced the unwanted oscillations. Active damping of the Remote Manipulator System with an attached 3990 lb. payload was successfully demonstrated. Six astronaut operators examined the performance of an Active Damping Augmentation control law following single-joint and coordinated six-joint translational and rotational maneuvers. Active Damping Augmentation disturbance rejection of Orbiter thruster firings was also evaluated. Significant reductions in the dynamic response of the 3990 lb. payload were observed. Astronaut operators recommended investigation of Active Damping Augmentation benefits to heavier payloads where oscillations are a bigger problem (e.g. Space Station Freedom assembly operators).

  20. The DAMPE silicon tungsten tracker

    CERN Document Server

    Gallo, Valentina; Asfandiyarov, R; Azzarello, P; Bernardini, P; Bertucci, B; Bolognini, A; Cadoux, F; Caprai, M; Domenjoz, M; Dong, Y; Duranti, M; Fan, R; Franco, M; Fusco, P; Gargano, F; Gong, K; Guo, D; Husi, C; Ionica, M; Lacalamita, N; Loparco, F; Marsella, G; Mazziotta, M N; Mongelli, M; Nardinocchi, A; Nicola, L; Pelleriti, G; Peng, W; Pohl, M; Postolache, V; Qiao, R; Surdo, A; Tykhonov, A; Vitillo, S; Wang, H; Weber, M; Wu, D; Wu, X; Zhang, F; De Mitri, I; La Marra, D

    2017-01-01

    The DArk Matter Particle Explorer (DAMPE) satellite has been successfully launched on the 17th December 2015. It is a powerful space detector designed for the identification of possible Dark Matter signatures thanks to its capability to detect electrons and photons with an unprecedented energy resolution in an energy range going from few GeV up to 10 TeV. Moreover, the DAMPE satellite will contribute to a better understanding of the propagation mechanisms of high energy cosmic rays measuring the nuclei flux up to 100 TeV. DAMPE is composed of four sub-detectors: a plastic strip scintillator, a silicon-tungsten tracker-converter (STK), a BGO imaging calorimeter and a neutron detector. The STK is made of twelve layers of single-sided AC-coupled silicon micro-strip detectors for a total silicon area of about 7 $m^2$ . To promote the conversion of incident photons into electron-positron pairs, tungsten foils are inserted into the supporting structure. In this document, a detailed description of the STK constructi...

  1. Vibrational Diver

    Science.gov (United States)

    Kozlov, Victor; Ivanova, Alevtina; Schipitsyn, Vitalii; Stambouli, Moncef

    2014-10-01

    The paper is concerned with dynamics of light solid in cavity with liquid subjected to rotational vibration in the external force field. New vibrational phenomenon - diving of a light cylinder to the cavity bottom is found. The experimental investigation of a horizontal annulus with a partition has shown that under vibration a light body situated in the upper part of the layer is displaced in a threshold manner some distance away from the boundary. In this case the body executes symmetric tangential oscillations. An increase of the vibration intensity leads to a tangential displacement of the body near the external boundary. This displacement is caused by the tangential component of the vibrational lift force, which appears as soon as the oscillations lose symmetry. In this case the trajectory of the body oscillatory motion has the form of a loop. The tangential lift force makes stable the position of the body on the inclined section of the layer and even in its lower part. A theoretical interpretation has been proposed, which explains stabilization of a quasi-equilibrium state of a light body near the cavity bottom in the framework of vibrational hydromechanics.

  2. Vibration Analysis and Design of a Structure Subjected to Human Walking Excitations

    Directory of Open Access Journals (Sweden)

    M. Setareh

    2010-01-01

    Full Text Available Annoying building floor vibrations have become a serious serviceability issue. This is mainly due to decrease in the system mass resulting from the use of higher strength materials; use of computer-assisted design and the Load and Resistance Factor Design Method to optimize the structure based on the strength requirements; fewer partitions and more innovative designs by architects achieving long, column free spans resulting in a reduction in the natural frequency and damping. This paper provides details of the vibration analysis and design of a novel office building. Three-dimensional computer models of the structure were created and various modifications were made to the original structure, designed based on static loads, to reduce the possible excessive floor vibrations when subjected to walking excitations. Tuned mass dampers were also designed as a back-up vibration control system. A series of dynamic tests were conducted on the building floor to identify the dynamic properties of the structure and these were then used to update the original computer model. Finally, various forcing functions representing human walks and the updated computer model of the structure were used to evaluate the accuracy of the walking excitation force models to predict the structural response. Conclusions are made on the validity of each forcing function studied here.

  3. Performance of improved magnetostrictive vibrational power generator, simple and high power output for practical applications

    Science.gov (United States)

    Ueno, Toshiyuki

    2015-05-01

    Vibration based power generation technology is utilized effectively in various fields. Author has invented novel vibrational power generation device using magnetostrictive material. The device is based on parallel beam structure consisting of a rod of iron-gallium alloy wound with coil and yoke accompanied with permanent magnet. When bending force is applied on the tip of the device, the magnetization inside the rod varies with induced stress due to the inverse magnetostrictive effect. In vibration, the time variation of the magnetization generates voltage on the wound coil. The magnetostrictive type is advantageous over conventional such using piezoelectric or moving magnet types in high efficiency and high robustness, and low electrical impedance. Here, author has established device configuration, simple, rigid, and high power output endurable for practical applications. In addition, the improved device is lower cost using less volume of Fe-Ga and permanent magnet compared to our conventional, and its assembly by soldering is easy and fast suitable for mass production. Average power of 3 mW/cm3 under resonant vibration of 212 Hz and 1.2 G was obtained in miniature prototype using Fe-Ga rod of 2 × 0.5× 7 mm3. Furthermore, the damping effect was observed, which demonstrates high energy conversion of the generator.

  4. A Stepwise Optimal Design of a Dynamic Vibration Absorber with Tunable Resonant Frequency

    Directory of Open Access Journals (Sweden)

    Jiejian DI

    2014-08-01

    Full Text Available A new kind of dynamic vibration absorber (DVA with tunable resonant frequency is presented. The kinematics differential equation about it is built and the stepwise optimization is performed. Firstly, four main system parameters involving the ratios of mass m, natural frequency f, vibration frequency g and damping z are solved by small-step-search method to obtain optimal steady state amplitude. Secondly, the sizing optimization of the dynamic vibration absorber is proceeded to search an optimal damping effect based on the optimal parameters (g, m, z, f. And such the damping effect is simulated in a flat structure, and the results show that the working frequency band and damping effect of the DVA after optimization won 20 % of the effect of ascension compared with that before optimization.

  5. Dynamic Optimization of Constrained Layer Damping Structure for the Headstock of Machine Tools with Modal Strain Energy Method

    Directory of Open Access Journals (Sweden)

    Yakai Xu

    2017-01-01

    Full Text Available Dynamic stiffness and damping of the headstock, which is a critical component of precision horizontal machining center, are two main factors that influence machining accuracy and surface finish quality. Constrained Layer Damping (CLD structure is proved to be effective in raising damping capacity for the thin plate and shell structures. In this paper, one kind of high damping material is utilized on the headstock to improve damping capacity. The dynamic characteristic of the hybrid headstock is investigated analytically and experimentally. The results demonstrate that the resonant response amplitudes of the headstock with damping material can decrease significantly compared to original cast structure. To obtain the optimal configuration of damping material, a topology optimization method based on the Evolutionary Structural Optimization (ESO is implemented. Modal Strain Energy (MSE method is employed to analyze the damping and to derive the sensitivity of the modal loss factor. The optimization results indicate that the added weight of damping material decreases by 50%; meanwhile the first two orders of modal loss factor decrease by less than 23.5% compared to the original structure.

  6. SEMI-ACTIVE DAMPING PERFORMANCE OF IRON PARTICLE FILLED SILICONE RUBBER

    Directory of Open Access Journals (Sweden)

    Florian Dirisamer

    2016-02-01

    Full Text Available The aim of this work was to design, produce and evaluate a demonstrator to visualize the magneto-induced damping behaviour of materials. In contrast to standard materials, the damping coefficient of iron particle filled silicone rubbers can be controlled by a semi-active magnetic field. This field effect should be characterized in order to evaluate the suitability of these magnetorheological silicone elastomers for the use in different configurations and applications.

  7. Stability analysis and active damping for LLCL-filter based grid-connected inverters

    DEFF Research Database (Denmark)

    Huang, Min; Blaabjerg, Frede; Loh, Poh Chiang

    2014-01-01

    A higher order passive power filter (LLCL-filter) for the grid-tied inverter is becoming attractive for the industrial applications due to the possibility to reduce the cost of the copper and the magnetic material. To avoid the well-known stability problems of the LLCL-filter it is requested to use...... either passive or active damping methods. This paper analyzes the stability when damping is required and when damping is not necessary considering sampling and transport delay. Basic LLCL resonance damping properties of different feedback states are also studied. Then an active damping method which...... is using the capacitor current feedback for LLCL-filter is introduced. Based on this method, a design procedure for the control method is given. Last, both simulation and experimental results are provided to validate the theoretical analysis of this paper....

  8. Energy-based damping evaluation of cable-stayed bridges and its application to Tsurumi Tsubasa bridge; Shachokyo shindo gensui no energy teki hyokaho to Tsurumi Tsubasakyo eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, H. [Saitama University, Saitama (Japan). Faculty of Engineering; Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Expressway Public Corp., Tokyo (Japan); Kato, M.; Kato, H. [NKK Corp., Tokyo (Japan)

    1996-07-21

    This paper provides and discusses a more common energy-based evaluation method of vibration damping in cable-stayed bridges. This method was applied to data obtained from the field vibration test of the Tsurumi Tsubasa Bridge. The damping was defined as dissipation energy in one cycle against the total potential energy. The dissipation energy from shoe friction, aerodynamic damping, and dampers for cables was added to the method proposed by Yamaguchi, et. al., in which the energy of girders, towers, and cables were quantitated, and the dissipation energy was determined from the loss factor of each constituent, to evaluate the damping of whole bridge. Thus, a more common energy-based evaluation method was provided. This method was applied to the damping obtained from the field vibration test of Tsurumi Tsubasa Bridge. Consequently, it was found that the damping of whole bridge was significantly affected by the shoe friction, aerodynamic damping, and dampers for cables. Distinguished damping characteristics of the Tsurumi Tsubasa Bridge could be explained by the energy-based evaluation. Validity of the energy-based evaluation method for damping of cable-stayed bridges was demonstrated. 15 refs., 9 figs., 6 tabs.

  9. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-08-31

    The deep hard rock drilling environment induces severe vibrations into the drillstring, which can cause reduced rates of penetration (ROP) and premature failure of the equipment. The only current means of controlling vibration under varying conditions is to change either the rotary speed or the weight-on-bit (WOB). These changes often reduce drilling efficiency. Conventional shock subs are useful in some situations, but often exacerbate the problems. The objective of this project is development of a unique system to monitor and control drilling vibrations in a ''smart'' drilling system. This system has two primary elements: (1) The first is an active vibration damper (AVD) to minimize harmful axial, lateral and torsional vibrations. The hardness of this damper will be continuously adjusted using a robust, fast-acting and reliable unique technology. (2) The second is a real-time system to monitor drillstring vibration, and related parameters. This monitor adjusts the damper according to local conditions. In some configurations, it may also send diagnostic information to the surface via real-time telemetry. The AVD is implemented in a configuration using magnetorheological (MR) fluid. By applying a current to the magnetic coils in the damper, the viscosity of the fluid can be changed rapidly, thereby altering the damping coefficient in response to the measured motion of the tool. Phase I of this program entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. Phase I of the project was completed by the revised end date of May 31, 2004. The objectives of this phase were met, and all prerequisites for Phase II have been completed.

  10. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-10-13

    The deep hard rock drilling environment induces severe vibrations into the drillstring, which can cause reduced rates of penetration (ROP) and premature failure of the equipment. The only current means of controlling vibration under varying conditions is to change either the rotary speed or the weight-on-bit (WOB). These changes often reduce drilling efficiency. Conventional shock subs are useful in some situations, but often exacerbate the problems. The objective of this project is development of a unique system to monitor and control drilling vibrations in a ''smart'' drilling system. This system has two primary elements: (1) The first is an active vibration damper (AVD) to minimize harmful axial, lateral and torsional vibrations. The hardness of this damper will be continuously adjusted using a robust, fast-acting and reliable unique technology. (2) The second is a real-time system to monitor drillstring vibration, and related parameters. This monitor adjusts the damper according to local conditions. In some configurations, it may also send diagnostic information to the surface via real-time telemetry. The AVD is implemented in a configuration using magnetorheological (MR) fluid. By applying a current to the magnetic coils in the damper, the viscosity of the fluid can be changed rapidly, thereby altering the damping coefficient in response to the measured motion of the tool. Phase I of this program entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. Phase I of the project was completed by the revised end date of May 31, 2004. The objectives of this phase were met, and all prerequisites for Phase II have been completed. The month of June, 2004 was primarily occupied with the writing of the Phase I Final Report, the sole deliverable of Phase I, which will be submitted in the next quarter. Redesign of the laboratory prototype and design of the downhole (Phase II) prototype was

  11. Fundamental study on the new method to estimate vibration level on a ship. Formulation of the damping matrix based on dissipation energy caused by fluid viscosity; Senpaku no shindo level suitei ni kansuru kisoteki kenkyu. Ryutai no nensei ni yoru san`itsu energy ni motozuku gensui matrix no teishikika

    Energy Technology Data Exchange (ETDEWEB)

    Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

    1996-12-31

    It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. In order to analyze the compound vibration therein, a method was proposed, which estimates vibration levels without using the finite element method. However, the problem of mode decay ratio has not been solved. Therefore, this paper first describes a method to introduce an equivalent linear decay matrix. The paper then mentions difference in the decay effects due to fluid viscosity in a shallow and deep water regions. Furthermore, vibration levels in the deep water region were estimated in a model experiment to verify the estimation result. Under a hypothesis that two-node vibration in a rotating ellipse has displacement distributions in the deep and shallow water regions equivalent, and when a case of vibration in a layer flow condition is calculated, dissipation energy in the shallow region is larger than that in the deep region by about 26%. About 5% of the total dissipation energy is consumed at bottom of the sea. According to a frequency response calculation, estimated values for the response levels still differ from experimental values, although the trend that the vibration levels change can be reproduced. 6 refs., 15 figs., 2 tabs.

  12. Reducing vibration transfer from power plants by active methods

    Science.gov (United States)

    Kiryukhin, A. V.; Milman, O. O.; Ptakhin, A. V.

    2017-12-01

    The possibility of applying the methods of active damping of vibration and pressure pulsations for reducing their transfer from power plants into the environment, the seating, and the industrial premises are considered. The results of experimental works implemented by the authors on the active broadband damping of vibration and dynamic forces after shock-absorption up to 15 dB in the frequency band up to 150 Hz, of water pressure pulsations in the pipeline up to 20 dB in the frequency band up to 600 Hz, and of spatial low-frequency air noise indoors of a diesel generator at discrete frequency up to 20 dB are presented. It is shown that a reduction of vibration transfer through a vibration-isolating junction (expansion joints) of pipelines with liquid is the most complicated and has hardly been developed so far. This problem is essential for vibration isolation of power equipment from the seating and the environment through pipelines with water and steam in the power and transport engineering, shipbuilding, and in oil and gas pipelines in pumping stations. For improving efficiency, reducing the energy consumption, and decreasing the overall dimensions of equipment, it is advisable to combine the work of an active system with passive damping means, the use of which is not always sufficient. The executive component of the systems of active damping should be placed behind the vibration isolators (expansion joints). It is shown that the existence of working medium and connection of vibration with pressure pulsations in existing designs of pipeline expansion joints lead to growth of vibration stiffness of the expansion joint with the environment by two and more orders as compared with the static stiffness and makes difficulties for using the active methods. For active damping of vibration transfer through expansion joints of pipelines with a liquid, it is necessary to develop expansion joint structures with minimal connection of vibrations and pulsations and minimal

  13. Analysis of long-range wakefields in CLIC main Linac Accelerating Structures with Damping Loads

    CERN Document Server

    De Michele, G

    2012-01-01

    The baseline design of the CLIC accelerating structure foresees a moderate detuning and heavy damping of high order modes (HOMs), which are the source of long-range transverse wakefields. Such unwanted fields produce bunch-to-bunch instabilities so the HOMs must be suppressed. In order to damp these modes, the CLIC RF structure is equipped with lossy material inserted into four rectangular waveguides coupled to each accelerating cell. The lossy material absorbs EM (electromagnetic) wave energy with little reflection back to the accelerating cells. In the past, computations of the long-range wake of CLIC accelerating modes have been done using perfectly absorbing boundaries to terminate the damping waveguides. In this paper, 3D EM simulations of CLIC baseline accelerating structure with HOMs damping loads will be presented. A comparison between different EM codes (GdfidL, CST PARTICLE STUDIO®) will be discussed as well as the analysis of different types of absorbing materials with respect to the wakefields da...

  14. VLTI-UT vibrations effort and performances

    Science.gov (United States)

    Poupar, Sébastien; Haguenauer, Pierre; Alonso, Jaime; Schuhler, Nicolas; Henriquez, Juan-Pablo; Berger, Jean-Philippe; Bourget, Pierre; Brillant, Stephane; Castillo, Roberto; Gitton, Philippe; Gonte, Frederic; Di Lieto, Nicola; Lizon, Jean-Louis; Merand, Antoine; Woillez, Julien

    2014-07-01

    The ESO Very Large Telescope Interferometer (VLTI) using the Unit Telescope (UT) was strongly affected by vibrations since the first observations. Investigation by ESO on that subject had started in 2007, with a considerable effort since mid 2008. An important number of investigations on various sub-systems (On telescope: Guiding, Passive supports, Train Coude, insulation of electronics cabinets; On Instruments: dedicated campaign on each instruments with a special attention on the ones equipped with Close Cycle Cooler) were realized. Vibrations were not only recorded and analyzed using the usual accelerometers but also using on use sub-systems as InfRared Image Sensor (IRIS) and Multiple Applications Curvature Adaptive Optics (MACAO) and using a specific tool developed for vibrations measurements Mirror vibrAtion Metrology systeM for the Unit Telescope (MAMMUT). Those tools and systems have been used in order to improve the knowledge on telescope by finding sources. The sources whenever it was possible were damped. As known for years, instruments are still the principal sources of vibrations, for the majority of the UT. A special test in which 2 UTs instruments were completely shut down was realized to determine the minimum Optical Path Length (OPL) achievable. Vibrations is now a part of the instruments interface document and during the installation of any new instrument (KMOS) or system (AOF) a test campaign is realized. As a result some modifications (damping of CCC) can be asked in case of non-compliance. To ensure good operational conditions, levels of vibrations are regularly recorded to control any environmental change.

  15. Dynamic soil-pile-interaction effects on eigenfrequency and damping of slender structures

    DEFF Research Database (Denmark)

    Zania, Varvara

    2014-01-01

    of the dynamic soil-pile-interaction on the natural vibration characteristics of the flexibly supported structure. For this purpose a two-step iterative procedure has been developed based on two analytical solutions. The frequency dependent dynamic stiffness and damping coefficients are taken into consideration......-conservative overestimation of the eigenfrequency and underestimation of damping especially for small slenderness ratios and high flexibility factor of the soil – pile system (short, rigid piles). The observed trends become even more prominent as the height of the slender structure increases. The effect of the monopile...... foundation properties on the natural vibration characteristics was also examined. The influence of the frequency dependent impedances was proven significant, since the modified SSI eigenfrequency decreased substantially, when the structural eigenfrequency was set between the first and the second...

  16. Actuator Control of Edgewise Vibrations in Wind Turbine Blades

    DEFF Research Database (Denmark)

    Staino, A.; Basu, B.; Nielsen, Søren R.K.

    2012-01-01

    Edgewise vibrations with low aerodynamic damping are of particular concern in modern multi-megawatt wind turbines, as large amplitude cyclic oscillations may significantly shorten the life-time of wind turbine components, and even lead to structural damages or failures. In this paper, a new blade ...

  17. CHARACTERIZATION OF DAMPING IN BOLTED LAP JOINTS

    Energy Technology Data Exchange (ETDEWEB)

    C. MALONEY; D. PEAIRS; ET AL

    2000-08-01

    The dynamic response of a jointed beam was measured in laboratory experiments. The data were analyzed and the system was mathematically modeled to establish plausible representations of joint damping behavior. Damping is examined in an approximate, local linear framework using log decrement and half power bandwidth approaches. in addition, damping is modeled in a nonlinear framework using a hybrid surface irregularities model that employs a bristles-construct. Experimental and analytical results are presented.

  18. Parametric Landau damping of space charge modes

    Energy Technology Data Exchange (ETDEWEB)

    Macridin, Alexandru [Fermilab; Burov, Alexey [Fermilab; Stern, Eric [Fermilab; Amundson, James [Fermilab; Spentzouris, Panagiotis [Fermilab

    2016-09-23

    Landau damping is the mechanism of plasma and beam stabilization; it arises through energy transfer from collective modes to the incoherent motion of resonant particles. Normally this resonance requires the resonant particle's frequency to match the collective mode frequency. We have identified an important new damping mechanism, parametric Landau damping, which is driven by the modulation of the mode-particle interaction. This opens new possibilities for stability control through manipulation of both particle and mode-particle coupling spectra. We demonstrate the existence of parametric Landau damping in a simulation of transverse coherent modes of bunched accelerator beams with space charge.

  19. Vibration analysis of continuous maglev guideways with a moving distributed load model

    Science.gov (United States)

    Teng, N. G.; Qiao, B. P.

    2008-02-01

    A model of moving distributed load with a constant speed is established for vertical vibration analysis of a continuous guideway in maglev transportation system. The guideway is considered as a continuous structural system and the action of maglev vehicles on guideways is considered as a moving distributed load. Vibration of the continuous guideways used in Shanghai maglev line is analyzed with this model. The factors that affect the vibration of the guideways, such as speeds, guideway's spans, frequency and damping, are discussed.

  20. Determination of aerodynamic damping of twin cables in wet conditions through passive-dynamic wind tunnel tests

    DEFF Research Database (Denmark)

    Eriksen, Mads Beedholm; Mattiello, E.; Georgakis, Christos T.

    2013-01-01

    operational modal analysis of the monitored vibrations revealed, in certain conditions and for specific wind velocities, the presence of negative aerodynamic damping.To investigate the observed aerodynamic damping of the twin cable arrangement further, a series of 1:2.3 scale passive-dynamic wind tunnel tests...... of the bridge cables. For the wet tests, the twin cable surfaces were treated in order to obtain uniform upper and lower water rivulets. The interaction between water rivulets, surface properties and the flow was found to govern the activation of the RWIV mechanism. The resulting aerodynamic damping from wet...... passive-dynamic wind tunnel tests showed the effect of the helical fillets in preventing the occurrence of negative aerodynamic damping, contrary to the plain cables. © 2013 Taylor & Francis Group, London, UK....

  1. Identification of pavement material properties using a scanning laser Doppler vibrometer

    Science.gov (United States)

    Hasheminejad, Navid; Vuye, Cedric; Van den Bergh, Wim; Dirckx, Joris; Leysen, Jari; Sels, Seppe; Vanlanduit, Steve

    2016-06-01

    This paper presents an inverse modeling approach to estimate mechanical properties of asphalt concrete (i.e. Young's modulus E, Poisson ratio ν and damping coefficients). Modal analysis was performed on an asphalt slab using a shaker to excite the specimen and an optical measurement system (a Scanning Laser Doppler Vibrometer or SLDV) to measure the velocity of a measurement grid on the surface of the slab. The SLDV has the ability to measure the vibration pattern of an object with high accuracy, short testing time and without making any contact. The measured data were used as inputs for a frequency domain model parameter estimation method (the Polymax estimator). Meanwhile, natural frequencies and damping ratios of the system were calculated using a Finite Element Modeling (FEM) method. Then, the Modal Assurance Criterion (MAC) was used to pair the mode shapes of the structure determined by measurements and estimated by FEM. By changing the inputs of the FEM analysis (E, ν and damping coefficients of the material) iteratively and minimizing the discrepancy between paired natural frequencies and damping ratios of the system estimated using the Polymax estimator and calculated by FEM, the Young's modulus, Poisson ratio and damping coefficients of the asphalt slab were estimated.

  2. An Experimental Technique for the Evaluation of Strain Dependent Material Properties of Hard Coatings

    Directory of Open Access Journals (Sweden)

    Shad A. Reed

    2008-01-01

    Full Text Available A novel vibration experiment consisting of a free-free boundary condition, an electromagnetic excitation source, a vacuum chamber, and a laser vibrometer based surface measurement system has been developed that permits high levels of excitation on highly damped specimens with a minimal amount of unwanted systematic error. While some of the aspects of this experiment are not unique, when combined with a processing technique that accounts for the nonlinearities present in the system, this experiment permits, accurate measurement of strain dependent stiffness and damping properties of hard coatings at high strain levels. This procedure has been demonstrated using a titanium beam that has been coated with a free-layer damping treatment of Magnesium Aluminate Spinel. The results indicate that Magnesium Aluminate Spinel has both nonlinear stiffness and damping properties. The stiffness asymptotes to a minimum value around 650 microstrain while the damping is a maximum around 100 microstrain. Additionally, the data contained herein cover a larger strain range for this material than previously reported.

  3. Susceptibility for cigarette smoke-induced DAMP release and DAMP-induced inflammation in COPD.

    Science.gov (United States)

    Pouwels, Simon D; Hesse, Laura; Faiz, Alen; Lubbers, Jaap; Bodha, Priya K; Ten Hacken, Nick H T; van Oosterhout, Antoon J M; Nawijn, Martijn C; Heijink, Irene H

    2016-11-01

    Cigarette smoke (CS) exposure is a major risk factor for chronic obstructive pulmonary disease (COPD). We investigated whether CS-induced damage-associated molecular pattern (DAMP) release or DAMP-mediated inflammation contributes to susceptibility for COPD. Samples, including bronchial brushings, were collected from young and old individuals, susceptible and nonsusceptible for the development of COPD, before and after smoking, and used for gene profiling and airway epithelial cell (AEC) culture. AECs were exposed to CS extract (CSE) or specific DAMPs. BALB/cByJ and DBA/2J mice were intranasally exposed to LL-37 and mitochondrial (mt)DAMPs. Functional gene-set enrichment analysis showed that CS significantly increases the airway epithelial gene expression of DAMPs and DAMP receptors in COPD patients. In cultured AECs, we observed that CSE induces necrosis and DAMP release, with specifically higher galectin-3 release from COPD-derived compared with control-derived cells. Galectin-3, LL-37, and mtDAMPs increased CXCL8 secretion in AECs. LL-37 and mtDAMPs induced neutrophilic airway inflammation, exclusively in mice susceptible for CS-induced airway inflammation. Collectively, we show that in airway epithelium from COPD patients, the CS-induced expression of DAMPs and DAMP receptors in vivo and the release of galectin-3 in vitro is exaggerated. Furthermore, our studies indicate that a predisposition to release DAMPs and subsequent induction of inflammation may contribute to the development of COPD. Copyright © 2016 the American Physiological Society.

  4. Vibrational stability of graphene

    Directory of Open Access Journals (Sweden)

    Yangfan Hu

    2013-05-01

    Full Text Available The mechanical stability of graphene as temperature rises is analyzed based on three different self-consistent phonon (SCP models. Compared with three-dimensional (3-D materials, the critical temperature Ti at which instability occurs for graphene is much closer to its melting temperature Tm obtained from Monte Carlo simulation (Ti ≃ 2Tm, K. V. Zakharchenko, A. Fasolino, J. H. Los, and M. I. Katsnelson, J. Phys. Condens. Matter 23, 202202. This suggests that thermal vibration plays a significant role in melting of graphene while melting for 3-D materials is often dominated by topologic defects. This peculiar property of graphene derives from its high structural anisotropy, which is characterized by the vibrational anisotropic coefficient (VAC, defined upon its Lindermann ratios in different directions. For any carbon based material with a graphene-like structure, the VAC value must be smaller than 5.4 to maintain its stability. It is also found that the high VAC value of graphene is responsible for its negative thermal expansion coefficient at low temperature range. We believe that the VAC can be regarded as a new criterion concerning the vibrational stability of any low-dimensional (low-D materials.

  5. Effect of nonlinearity of connecting dampers on vibration control of connected building structures

    Directory of Open Access Journals (Sweden)

    Masatoshi eKasagi

    2016-01-01

    Full Text Available The connection of two building structures with dampers is one of effective vibration control systems. In this vibration control system, both buildings have to possess different vibration properties in order to provide a higher vibration reduction performance. In addition to such condition of different vibration properties of both buildings, the connecting dampers also play an important role in the vibration control mechanism. In this paper, the effect of nonlinearity of connecting dampers on the vibration control of connected building structures is investigated in detail. A high-damping rubber damper and an oil damper with and without relief mechanism are treated. It is shown that, while the high-damping rubber damper is effective in a rather small deformation level, the linear oil damper is effective in a relatively large deformation level. It is further shown that, while the oil dampers reduce the response in the same phase as the case without dampers, the high-damping rubber dampers change the phase. The merit is that the high-damping rubber can reduce the damper deformation and keep the sufficient space between both buildings. This can mitigate the risk of building pounding.

  6. Vibrating minds

    CERN Document Server

    2009-01-01

    Ed Witten is one of the leading scientists in the field of string theory, the theory that describes elementary particles as vibrating strings. This week he leaves CERN after having spent a few months here on sabbatical. His wish is that the LHC will unveil supersymmetry.

  7. Parameter identification in a generalized time-harmonic Rayleigh damping model for elastography.

    Directory of Open Access Journals (Sweden)

    Elijah E W Van Houten

    Full Text Available The identifiability of the two damping components of a Generalized Rayleigh Damping model is investigated through analysis of the continuum equilibrium equations as well as a simple spring-mass system. Generalized Rayleigh Damping provides a more diversified attenuation model than pure Viscoelasticity, with two parameters to describe attenuation effects and account for the complex damping behavior found in biological tissue. For heterogeneous Rayleigh Damped materials, there is no equivalent Viscoelastic system to describe the observed motions. For homogeneous systems, the inverse problem to determine the two Rayleigh Damping components is seen to be uniquely posed, in the sense that the inverse matrix for parameter identification is full rank, with certain conditions: when either multi-frequency data is available or when both shear and dilatational wave propagation is taken into account. For the multi-frequency case, the frequency dependency of the elastic parameters adds a level of complexity to the reconstruction problem that must be addressed for reasonable solutions. For the dilatational wave case, the accuracy of compressional wave measurement in fluid saturated soft tissues becomes an issue for qualitative parameter identification. These issues can be addressed with reasonable assumptions on the negligible damping levels of dilatational waves in soft tissue. In general, the parameters of a Generalized Rayleigh Damping model are identifiable for the elastography inverse problem, although with more complex conditions than the simpler Viscoelastic damping model. The value of this approach is the additional structural information provided by the Generalized Rayleigh Damping model, which can be linked to tissue composition as well as rheological interpretations.

  8. Enhanced damping for bridge cables using a self-sensing MR damper

    Science.gov (United States)

    Chen, Z. H.; Lam, K. H.; Ni, Y. Q.

    2016-08-01

    This paper investigates enhanced damping for protecting bridge stay cables from excessive vibration using a newly developed self-sensing magnetorheological (MR) damper. The semi-active control strategy for effectively operating the self-sensing MR damper is formulated based on the linear-quadratic-Gaussian (LQG) control by further considering a collocated control configuration, limited measurements and nonlinear damper dynamics. Due to its attractive feature of sensing-while-damping, the self-sensing MR damper facilitates the collocated control. On the other hand, only the sensor measurements from the self-sensing device are employed in the feedback control. The nonlinear dynamics of the self-sensing MR damper, represented by a validated Bayesian NARX network technique, are further accommodated in the control formulation to compensate for its nonlinearities. Numerical and experimental investigations are conducted on stay cables equipped with the self-sensing MR damper operated in passive and semi-active control modes. The results verify that the collocated self-sensing MR damper facilitates smart damping for inclined cables employing energy-dissipative LQG control with only force and displacement measurements at the damper. It is also demonstrated that the synthesis of nonlinear damper dynamics in the LQG control enhances damping force tracking efficiently, explores the features of the self-sensing MR damper, and achieves better control performance over the passive MR damping control and the Heaviside step function-based LQG control that ignores the damper dynamics.

  9. Gyroscopic Stabilization of Indefinite Damped Systems

    DEFF Research Database (Denmark)

    Kliem, Wolfhard; Müller, Peter C.

    1997-01-01

    Modelling of mechanical systems with sliding bearings, or with dry friction, can lead to linear systems with an indefinite damping matrix. We ask under what conditions such a system is unstable (the indefiniteness of the damping matrix is not enough) and under what conditions we can stabilize the...... the system by adding a gyroscopic term....

  10. Damping device for a stationary labyrinth seal

    Science.gov (United States)

    El-Aini, Yehia M. (Inventor); Mitchell, William S. (Inventor); Roberts, Lawrence P. (Inventor); Montgomery, Stuart K. (Inventor); Davis, Gary A. (Inventor)

    2010-01-01

    A stationary labyrinth seal system includes a seal housing having an annular cavity, a plurality of damping devices, and a retaining ring. The damping devices are positioned within the annular cavity and are maintained within the annular cavity by the retaining ring.

  11. DAMPs from death to new life

    Directory of Open Access Journals (Sweden)

    Emilie eVénéreau

    2015-08-01

    Full Text Available Our body handles tissue damage by activating the immune system in response to intracellularmolecules released by injured tissues (Damage-Associated Molecular Patterns, DAMPs, in a similar way as it detects molecular motifs conserved in pathogens (pathogen-associated molecular patterns, PAMPs. DAMPs are molecules that have a physiological role inside the cell, but acquire additional functions when they are released outside the cell: they alert the body about danger, stimulate an inflammatory response, and finally promote the regeneration process. Beside their passive release by dead cells, some DAMPs can be secreted or exposed by living cells undergoing a life-threatening stress. DAMPs have been linked to inflammation and related disorders: hence, inhibition of DAMP-mediated inflammatory responses is a promising strategy to improve the clinical management of infection- and injury-elicited inflammatory diseases. However, it is important to consider that DAMPs are not only danger signals but also central players in tissue repair. Indeed, some DAMPs have been studied for their role in tissue healing after sterile or infection-associated inflammation. This review is focused on two exemplary DAMPs, HMGB1 and ATP, and their contribution to both inflammation and tissue repair.

  12. Damping-off in forest nurseries

    Science.gov (United States)

    Carl Hartley

    1921-01-01

    Damping-off is the commonest English name for a symptomatic group of diseases affecting great numbers of plant species of widely separated phylogenetic groups. It is commonly used for any disease which results in the rapid decay of young succulent seedlings or soft cuttings. Young shoots from underground rootstocks may also be damped-off before they break through the...

  13. On Collisionless Damping of Ion Acoustic Waves

    DEFF Research Database (Denmark)

    Jensen, Vagn Orla; Petersen, P.I.

    1973-01-01

    Exact theoretical treatments show that the damping of ion acoustic waves in collisionless plasmas does not vanish when the derivative of the undisturbed distribution function at the phase velocity equals zero.......Exact theoretical treatments show that the damping of ion acoustic waves in collisionless plasmas does not vanish when the derivative of the undisturbed distribution function at the phase velocity equals zero....

  14. Dynamic characteristics of the blisk with synchronized switch damping based on negative capacitor

    Science.gov (United States)

    Liu, J.; Li, L.; Huang, X.; Jezequel, L.

    2017-10-01

    In this paper, we propose a method to suppress the vibration of the integral bladed disk ('blisk' for short) in aero-engines using synchronized switch damping based on negative capacitor (SSDNC). Different from the classical piezoelectric shunt damping, SSDNC is a type of nonlinear piezoelectric damping. A multi-harmonic balance method combined with the alternating frequency/time method (MHBM-AFT) is used to predict and further analyze the dynamic characteristics of the electromechanical system, and an arc-length continuation technique is used to improve the convergence of the method. In order to validate the algorithm as well as to recognize the characteristics of the system with SSDNC, a two degree-of-freedom (2-DOF) system with SSDNC is studied at first. The nonlinear complex modal information is calculated and compared with those of the corresponding system with a linear RL shunt circuit. The results indicate that the natural frequencies and modal damping ratio do not change with the modal amplitude, which means that SSDNC has the same modal damping corresponding to different system energy levels. In addition, SSDNC can improve the damping level of all the modes nearly without affecting the natural frequencies of the system. Then, the forced response of the blisk with SSDNC in the frequency domain is calculated and analyzed, including a tuned blisk, which is excited by the traveling wave excitation with a single harmonic and multi-harmonic, and a mistuned blisk, which is excited by traveling wave excitation with a single harmonic and multi-harmonic. We present two advantages of the SSDNC technique when compared with piezoelectric shunt damping. First, SSDNC can suppress the vibration of the blisk under a multi-harmonic wideband the traveling wave, and second, the vibration suppression performance of SSDNC is insensitive to the mistuning of mechanical parameters of the blisk. The results will be of great significance in overcoming the problem of the amplitude

  15. Allergy and respiratory health effects of dampness and dampness-related agents in schools and homes

    DEFF Research Database (Denmark)

    Holst, G; Høst, Arne; Doekes, G

    2016-01-01

    Little is known about the health effects of school-related indoor dampness and microbial exposures. In this study we investigated dampness and dampness-related agents in both homes and schools and their association with allergy and respiratory health effects in 330 Danish pupils. Classroom dampness...... was identified based on technical inspection and bedroom dampness on parents' self-report. Classroom and bedroom dust was analysed for seven microbial components. Skin-prick-testing determined atopic sensitisation. Lung function was expressed as z-scores for forced expiratory volume in one second (zFEV1...... ), forced vital capacity (zFVC) and the ratio zFEV1 /zFVC using GLI-2012-prediction-equations. The parents reported children's allergies, airway symptoms and doctor-diagnosed asthma. High classroom dampness, but not bedroom dampness, was negatively associated with zFEV1 (β-coef. -0.71; 95%CI -1.17 - -0...

  16. Dynamic Stall in Pitching Airfoils: Aerodynamic Damping and Compressibility Effects

    Science.gov (United States)

    Corke, Thomas C.; Thomas, Flint O.

    2015-01-01

    Dynamic stall is an incredibly rich fluid dynamics problem that manifests itself on an airfoil during rapid, transient motion in which the angle of incidence surpasses the static stall limit. It is an important element of many manmade and natural flyers, including helicopters and supermaneuverable aircraft, and low-Reynolds number flapping-wing birds and insects. The fluid dynamic attributes that accompany dynamic stall include an eruption of vorticity that organizes into a well-defined dynamic stall vortex and massive excursions in aerodynamic loads that can couple with the airfoil structural dynamics. The dynamic stall process is highly sensitive to surface roughness that can influence turbulent transition and to local compressibility effects that occur at free-stream Mach numbers that are otherwise incompressible. Under some conditions, dynamic stall can result in negative aerodynamic damping that leads to limit-cycle growth of structural vibrations and rapid mechanical failure. The mechanisms leading to negative damping have been a principal interest of recent experiments and analysis. Computational fluid dynamic simulations and low-order models have not been good predictors so far. Large-eddy simulation could be a viable approach although it remains computationally intensive. The topic is technologically important owing to the desire to develop next-generation rotorcraft that employ adaptive rotor dynamic stall control.

  17. Experimental investigation on the dynamic mechanical properties of soft magnetic entangled metallic wire material

    Science.gov (United States)

    Ma, Yanhong; Zhang, Qicheng; Zhang, Dayi; Hu, Wenzhong; Hong, Jie

    2017-05-01

    This work describes the dynamic characteristics of a novel soft magnetic entangled metallic wire material(SM-EMWM) by the dynamic tests for the first time. The mechanical properties of three batches of SM-EMWMs with different porosities have been investigated under different dynamic loads in different magnetic field intensities. The result shows that its properties (storage modulus and loss factor) have commendably controllable magnetic responses in the magnetic field. In particular, the dynamic damping is more remarkable than its quasi-static performance, and the loss factor can be improved above 50% in the magnetic field of 500 mT. The results indicate that SM-EMWM as a magneto-sensitive smart material possesses a considerable application prospect for the active vibration control with variable stiffness and damping.

  18. Experimental Study on Variation Rules of Damping with Influential Factors of Tuned Liquid Column Damper

    Directory of Open Access Journals (Sweden)

    Yang Yu

    2017-01-01

    Full Text Available A tuned liquid column damper (TLCD is a more effective form of passive control for structural vibration suppression and may be promising for floating platform applications. To achieve good damping effects for a TLCD under actual working conditions, factors that influence the damping characteristics need to be identified. In this study, the relationships between head loss coefficients and other factors such as the total length of the liquid column, opening ratio, Reynolds number, Kc number, and horizontal length of the liquid column were experimentally investigated. By using a hydraulic vibration table, a vibration test system with large-amplitude motion simulation, low-frequency performance, and large stroke force (displacement control is devised with a simple operation and at low cost. Based on the experimental method of uniform design, a series of experimental studies were conducted to determine the quantitative relationships between the head loss coefficient and other factors. In addition, regression analyses indicated the importance of each factor affecting the head loss coefficient. A rapid design strategy of TLCD head loss coefficient is proposed. This strategy can help people conveniently and efficiently adjust the head loss coefficient to a specified value to effectively suppress vibration.

  19. Experimental Study on Vibration Reduction Characteristics of Gear Shafts Based on ISFD Installation Position

    Directory of Open Access Journals (Sweden)

    Kaihua Lu

    2017-01-01

    Full Text Available A novel type of integral squeeze film damper (ISFD is proposed to reduce and isolate vibration excitations of the gear system through bearing to the foundation. Four ISFD designs were tested experimentally with an open first-grade spur gear system. Vibration reduction characteristics were experimentally studied at different speeds for cases where ISFD elastic damping supports were simultaneously installed on the driving and driven shafts, installed on the driven shaft, or only installed on the driving shaft. Experimental results show that the ISFD elastic damping support can effectively reduce shock vibration of the gear system. Additionally, resonant modulation in gear shafts caused by meshing impact was significantly reduced. Different vibration amplitudes of gear shafts with ISFD installed only on driven or driving shafts were compared. Results indicated that vibration reduction is better when ISFD is only installed on the driven shaft than on the driving shaft.

  20. Lateral vibration control of a flexible overcritical rotor via an active gas bearing – Theoretical and experimental comparisons

    DEFF Research Database (Denmark)

    Pierart Vásquez, Fabián Gonzalo; Santos, Ilmar

    2016-01-01

    The lack of damping of radial gas bearings leads to high vibration levels of a rotor supported by this type of bearing when crossing resonant areas. This is even more relevant for flexible rotors, as studied in this work. In order to reduce these high vibration levels, an active gas bearing is pr...

  1. Sweeping shunted electro-magnetic tuneable vibration absorber: Design and implementation

    Science.gov (United States)

    Turco, E.; Gardonio, P.

    2017-10-01

    This paper presents a study on the design and implementation of a time-varying shunted electro-magnetic Tuneable Vibration Absorber for broad-band vibration control of thin structures. A time-varying RL-shunt is used to harmonically vary the stiffness and damping properties of the Tuneable Vibration Absorber so that its mechanical fundamental natural frequency is continuously swept in a given broad frequency band whereas its mechanical damping is continuously adapted to maximize the vibration absorption from the hosting structure where it is mounted. The paper first recalls the tuning and positioning criteria for the case where a classical Tuneable Vibration Absorber is installed on a thin walled cylindrical structure to reduce the response of a resonating flexural mode. It then discusses the design of the time-varying shunt circuit to produce the desired stiffness and damping variations in the electro-magnetic Tuneable Vibration Absorber. Finally, it presents a numerical study on the flexural vibration and interior sound control effects produced when an array of these shunted electro-magnetic Tuneable Vibration Absorbers are mounted on a thin walled cylinder subject to a rain-on-the-roof stochastic excitation. The study shows that the array of proposed systems effectively controls the cylinder flexural response and interior noise over a broad frequency band without need of tuning and thus system identification of the structure. Therefore, the systems can be successfully used also on structures whose physical properties vary in time because of temperature changes or tensioning effects for example.

  2. Parametric study on a collocated PZT beam vibration absorber and power harvester

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Shyh Chin [Mechanical Engineering, Ming Chi University of Technology, New Taipei (China); Tsai, Chao Yang [Mechanical Engineering Army Academy, R.O.C., Taoyuan (China); Liao, Hsiao Hui [LNG Construction and Project Division, CPC Corp., Taipei (China)

    2016-11-15

    The parametric effects of a PZT beam that is simultaneously used as a vibration absorber and a power harvester were investigated in this study. A cantilever beam paved with PZT layers and with added tip mass has been widely used as a harvester or sometimes as a Dynamic vibration absorber (DVA). However, the beam is rarely considered a collocated device. In this study, the first step was theoretical derivation of a distributed beam covered with bimorph PZT layers. Then, the beam was attached to a 1DOF vibratory main system. Two indicators for vibration absorption and power harvesting were defined. Numerical results demonstrated that the lumped mass ratio favored both of the abilities, but that the DVA mass ratio influenced these two abilities in exactly the opposite way. The conjunction of a harvester circuit into a DVA shifted its resonance frequency up to 5 % (an extreme case of open circuit R→∞). Simultaneous power harvesting diminished the absorption capability up to 35 % for each set of mass ratios. To achieve the maximum degree of power harvesting, a corresponding load resistance that somewhat increases with the lumped mass ratio is applied. Experimental results verified the existence of the best load resistance, but the measured harvested curve was lower than the theoretical calculation because of structure damping and deviations of PZT material properties.

  3. Vibration Analysis of a Tire in Ground Contact under Varied Conditions

    Directory of Open Access Journals (Sweden)

    Karakus Murat

    2017-03-01

    Full Text Available The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13 has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different coefficients of friction. Experiments are run under certain conditions to check the accuracy of the numerical model. The natural frequencies are measured to describe free vibration and vibration of the tire contacted by ground, using a damping monitoring method. It is seen, that experimental and numerical results are in good agreement. On the other hand, investigating the impact of three different factors together is quite difficult on the natural frequencies. When some of these factors are assumed to be constant and the variables are taken one by one, it is easier to assess the effects.

  4. Experimental Active Vibration Control in Truss Structures Considering Uncertainties in System Parameters

    Directory of Open Access Journals (Sweden)

    Douglas Domingues Bueno

    2008-01-01

    Full Text Available This paper deals with the study of algorithms for robust active vibration control in flexible structures considering uncertainties in system parameters. It became an area of enormous interest, mainly due to the countless demands of optimal performance in mechanical systems as aircraft, aerospace, and automotive structures. An important and difficult problem for designing active vibration control is to get a representative dynamic model. Generally, this model can be obtained using finite element method (FEM or an identification method using experimental data. Actuators and sensors may affect the dynamics properties of the structure, for instance, electromechanical coupling of piezoelectric material must be considered in FEM formulation for flexible and lightly damping structure. The nonlinearities and uncertainties involved in these structures make it a difficult task, mainly for complex structures as spatial truss structures. On the other hand, by using an identification method, it is possible to obtain the dynamic model represented through a state space realization considering this coupling. This paper proposes an experimental methodology for vibration control in a 3D truss structure using PZT wafer stacks and a robust control algorithm solved by linear matrix inequalities.

  5. Pickin’ up good vibrations

    CERN Multimedia

    Katarina Anthony

    2015-01-01

    In preparation for the civil engineering work on the HL-LHC, vibration measurements were carried out at the LHC’s Point 1 last month. These measurements will help evaluate how civil engineering work could impact the beam, and will provide crucial details about the site’s geological make-up before construction begins.   A seismic truck at Point 1 generated wave-like vibrations measured by EN/MME. From carrying out R&D to produce state-of-the-art magnets to developing innovative, robust materials capable of withstanding beam impact, the HL-LHC is a multi-faceted project involving many groups and teams across CERN’s departments. It was in this framework that the project management mandated CERN's Mechanical and Materials Engineering (EN/MME) group to measure the propagation of vibrations around Point 1. Their question: can civil engineering work for the HL-LHC – the bulk of which is scheduled for LS2 – begin while the LHC is running? Alth...

  6. Radiation damping of a polarizable particle

    Science.gov (United States)

    Novotny, Lukas

    2017-09-01

    A polarizable body moving in an external electromagnetic field will slow down. This effect is referred to as radiation damping and is analogous to Doppler cooling in atomic physics. Using the principles of special relativity we derive an expression for the radiation damping force and find that it solely depends on the scattered power. The cooling of the particle's center-of-mass motion is balanced by heating due to radiation pressure shot noise, giving rise to an equilibrium that depends on the ratio of the field's frequency and the particle's mass. While damping is of relativistic nature, heating has its roots in quantum mechanics.

  7. Lifetime measurement of ATF damping ring

    Energy Technology Data Exchange (ETDEWEB)

    Okugi, T. [Tokyo Metropolitan Univ. (Japan); Hayano, H.; Kubo, K.; Naito, T.; Terunuma, N.; Urakawa, J. [High Energy Accelerator Research Organization, Tsukuba (Japan); Zimmermann, F. [Stanford Univ., CA (US). Stanford Linear Accelerator Center

    1998-06-01

    The purpose of the ATF damping ring is the development of technologies for producing a low emittance beam required in future linear colliders such as JLC. The lifetime of the damping ring is very short (typically a few minutes). It is limited by elastic beam-gas scattering along with a small dynamic aperture, and by single intra-beam scattering (Touschek effect). The Touschek lifetime strongly depends upon the charge density of the beam, especially, the size of the vertical emittance. In this paper, the authors report the results of beam lifetime measurements in the ATF damping ring and the estimation of the vertical emittance from these measurements.

  8. Urban vibrations

    DEFF Research Database (Denmark)

    Morrison, Ann; Knudsen, L.; Andersen, Hans Jørgen

    2012-01-01

      lab   studies   in   that   we   found   a   decreased   detection   rate   in   busy   environments.   Here   we   test   with   a   much   larger   sample   and   age   range,   and   contribute   with   the   first   vibration  sensitivity  testing  outside  the  lab  in  an  urban   public...

  9. Dynamically Tuned Blade Pitch Links for Vibration Reduction

    Science.gov (United States)

    Milgram, Judah; Chopra, Inderjit; Kottapalli, Sesi

    1994-01-01

    A passive vibration reduction device in which the conventional main rotor blade pitch link is replaced by a spring/damper element is investigated using a comprehensive rotorcraft analysis code. A case study is conducted for a modern articulated helicopter main rotor. Correlation of vibratory pitch link loads with wind tunnel test data is satisfactory for lower harmonics. Inclusion of unsteady aerodynamics had little effect on the correlation. In the absence of pushrod damping, reduction in pushrod stiffness from the baseline value had an adverse effect on vibratory hub loads in forward flight. However, pushrod damping in combination with reduced pushrod stiffness resulted in modest improvements in fixed and rotating system hub loads.

  10. Stochastic Response of Energy Balanced Model for Vortex-Induced Vibration

    DEFF Research Database (Denmark)

    Nielsen, Søren R.K.; Krenk, S.

    of lightly damped structures are found on two branches, with the highest amplification branch on the low-frequency branch. The effect free wind turbulence is to destabilize the vibrations on the high amplification branch, thereby reducing the oscillation amplitude. The effect is most pronounced for very......A double oscillator model for vortex-induced oscillations of structural elements based on exact power exchange between fluid and structure, recently proposed by authors, is extended to include the effect of the turbulent component of the wind. In non-turbulent flow vortex-induced vibrations...... lightly damped structures. The character of the structural vibrations changes with increasing turbulence and damping from nearly regular harmonic oscillation to typical narrow-banded stochastic response, closely resembling observed behaviour in experiments and full-scale structures....

  11. Vibration energy harvester with sustainable power based on a single-crystal piezoelectric cantilever array.

    Science.gov (United States)

    Kim, Moonkeun; Lee, Sang-Kyun; Ham, Yong-Hyun; Yang, Yil Suk; Kwon, Jong-Kee; Kwon, Kwang-Ho

    2012-08-01

    We designed and fabricated a bimorph cantilever array for sustainable power with an integrated Cu proof mass to obtain additional power and current. We fabricated a cantilever system using single-crystal piezoelectric material and compared the calculations for single and arrayed cantilevers to those obtained experimentally. The vibration energy harvester had resonant frequencies of 60.4 and 63.2 Hz for short and open circuits, respectively. The damping ratio and quality factor of the cantilever device were 0.012 and 41.66, respectively. The resonant frequency at maximum average power was 60.8 Hz. The current and highest average power of the harvester array were found to be 0.728 mA and 1.61 mW, respectively. The sustainable maximum power was obtained after slightly shifting the short-circuit frequency. In order to improve the current and power using an array of cantilevers, we also performed energy conversion experiments.

  12. Seismic Analysis of a Viscoelastic Damping Isolator

    Directory of Open Access Journals (Sweden)

    Bo-Wun Huang

    2015-01-01

    Full Text Available Seismic prevention issues are discussed much more seriously around the world after Fukushima earthquake, Japan, April 2011, especially for those countries which are near the earthquake zone. Approximately 1.8×1012 kilograms of explosive energy will be released from a magnitude 9 earthquake. It destroys most of the unprotected infrastructure within several tens of miles in diameter from the epicenter. People can feel the earthquake even if living hundreds of miles away. This study is a seismic simulation analysis for an innovated and improved design of viscoelastic damping isolator, which can be more effectively applied to earthquake prevention and damage reduction of high-rise buildings, roads, bridges, power generation facilities, and so forth, from earthquake disaster. Solidworks graphic software is used to draw the 3D geometric model of the viscoelastic isolator. The dynamic behavior of the viscoelastic isolator through shock impact of specific earthquake loading, recorded by a seismometer, is obtained via ANSYS finite element package. The amplitude of the isolator is quickly reduced by the viscoelastic material in the device and is shown in a time response diagram. The result of this analysis can be a crucial reference when improving the design of a seismic isolator.

  13. Simplified Model of Nonlinear Landau Damping

    Energy Technology Data Exchange (ETDEWEB)

    N. A. Yampolsky and N. J. Fisch

    2009-07-16

    The nonlinear interaction of a plasma wave with resonant electrons results in a plateau in the electron distribution function close to the phase velocity of the plasma wave. As a result, Landau damping of the plasma wave vanishes and the resonant frequency of the plasma wave downshifts. However, this simple picture is invalid when the external driving force changes the plasma wave fast enough so that the plateau cannot be fully developed. A new model to describe amplification of the plasma wave including the saturation of Landau damping and the nonlinear frequency shift is proposed. The proposed model takes into account the change of the plasma wave amplitude and describes saturation of the Landau damping rate in terms of a single fluid equation, which simplifies the description of the inherently kinetic nature of Landau damping. A proposed fluid model, incorporating these simplifications, is verified numerically using a kinetic Vlasov code.

  14. Piezoelectric RL shunt damping of flexible structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker; Krenk, Steen

    2015-01-01

    Resonant RL shunt circuits represent a robust and effective approach to piezoelectric damping, provided that the individual shunt circuit components are calibrated accurately with respect to the dynamic properties of the corresponding flexible structure. The balanced calibration procedure applied...

  15. Offline software for the DAMPE experiment

    Science.gov (United States)

    Wang, Chi; Liu, Dong; Wei, Yifeng; Zhang, Zhiyong; Zhang, Yunlong; Wang, Xiaolian; Xu, Zizong; Huang, Guangshun; Tykhonov, Andrii; Wu, Xin; Zang, Jingjing; Liu, Yang; Jiang, Wei; Wen, Sicheng; Wu, Jian; Chang, Jin

    2017-10-01

    A software system has been developed for the DArk Matter Particle Explorer (DAMPE) mission, a satellite-based experiment. The DAMPE software is mainly written in C++ and steered using a Python script. This article presents an overview of the DAMPE offline software, including the major architecture design and specific implementation for simulation, calibration and reconstruction. The whole system has been successfully applied to DAMPE data analysis. Some results obtained using the system, from simulation and beam test experiments, are presented. Supported by Chinese 973 Program (2010CB833002), the Strategic Priority Research Program on Space Science of the Chinese Academy of Science (CAS) (XDA04040202-4), the Joint Research Fund in Astronomy under cooperative agreement between the National Natural Science Foundation of China (NSFC) and CAS (U1531126) and 100 Talents Program of the Chinese Academy of Science

  16. Structural and vibrational studies of LiNi{sub 1-y}Co{sub y}VO{sub 4} (0{<=}y{<=}1) cathodes materials for Li-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Julien, C.; Massot, M. [Univ. Pierre et Marie Curie, Paris (France). Lab. des Milieux Desordonnes et Heterogenes; Perez-Vicente, C. [Laboratoire des Agregats Moleculaires et Materiaux Inorganiques, CC-015, Universite de Montpellier II, place Eugene-Bataillon, 34095, Montpellier (France)

    2000-05-15

    The structure and vibrational properties of high voltage cathode materials, namely LiNi{sub 1-y}CO{sub y}VO{sub 4} solid solution with (0{<=}y{<=}1), have been studied using X-ray diffraction, Raman scattering and FTIR measurements. Rietveld refinements show that LiNi{sub 1-y}Co{sub y}VO{sub 4} vanadates belong to the inverse spinel structure with Fd3m(O{sup 7}{sub h}) space group. Analysis of Raman spectra has been carried out in the molecular approximation using a local environment model including VO{sub 4} tetrahedra, (Ni, Co)O{sub 6} and LiO{sub 6} octahedra as vibrational local units. (orig.)

  17. The Damping Tail of CMB Anisotropies

    OpenAIRE

    Hu, Wayne; White, Martin

    1996-01-01

    By decomposing the damping tail of CMB anisotropies into a series of transfer functions representing individual physical effects, we provide ingredients that will aid in the reconstruction of the cosmological model from small-scale CMB anisotropy data. We accurately calibrate the model-independent effects of diffusion and reionization damping which provide potentially the most robust information on the background cosmology. Removing these effects, we uncover model-dependent processes such as ...

  18. Nonlinear damping and quasi-linear modelling

    OpenAIRE

    Elliott, S J; Ghandchi Tehrani, Maryam; Langley, R.

    2015-01-01

    The mechanism of energy dissipation in mechanical systems is often nonlinear. Even though there may be other forms of nonlinearity in the dynamics, nonlinear damping is the dominant source of nonlinearity in a number of practical systems. The analysis of such systems is simplified by the fact that they show no jump or bifurcation behaviour, and indeed can often be well represented by an equivalent linear system, whose damping parameters depend on the form and amplitude of the excitation, in a...

  19. CLIC Waveguide Damped Accelerating Structure Studies

    CERN Document Server

    Dehler, M; Wuensch, Walter

    1996-01-01

    Studies of waveguide damped 30 GHz accelerating structures for multibunching in CLIC are described. Frequency discriminated damping using waveguides with a lowest cutoff frequency above the fundamental but below the higher order modes was considered. The wakefield behavior was investigated using time domain MAFIA computations over up to 20 cells and for frequencies up to 150 GHz. A configuration consisting of four T-cross-sectioned waveguides per cell reduces the transverse wake below 1% at typical CLIC bunch spacings.

  20. On a Nonlocal Damping Model in Ferromagnetism

    Directory of Open Access Journals (Sweden)

    M. Moumni

    2015-01-01

    Full Text Available We consider a mathematical model describing nonlocal damping in magnetization dynamics. The model consists of a modified form of the Landau-Lifshitz-Gilbert (LLG equation for the evolution of the magnetization vector in a rigid ferromagnet. We give a global existence result and characterize the long time behaviour of the obtained solutions. The sensitivity of the model with respect to large and small nonlocal damping parameters is also discussed.