A Hybrid Soft Soil Tire Model (HSSTM) For Vehicle Mobility And Deterministic Performance Analysis In Terramechanics Applications

OpenAIRE

Taheri, Shahyar

2015-01-01

Accurate and efficient tire models for deformable terrain operations are essential for performing vehicle simulations. Assessment of the forces and moments that occur at the tire-terrain interface, and the effect of the tire motion on properties of the terrain are crucial in understanding the performance of a vehicle. In order to model the dynamic behavior of the tire on different terrains, a lumped mass discretized tire model using Kelvin-Voigt elements is developed. To optimize the computat...

Conversion of Hazardous Motor Vehicle Used Tire and Polystyrene Waste Plastic Mixture into useful Chemical Products

OpenAIRE

Moinuddin Sarker; Mohammad Mamunor Rashid

2014-01-01

Motor vehicle used tire and polystyrene waste plastic mixture into fuel recovery using thermal degradation process in laboratory batch process. Motor vehicle used tire and polystyrene waste plastic was use 75 gm by weight. Motor vehicle tire was 25 gm and polystyrene waste plastic was 50 gm. In presence of oxygen experiment was performed under laboratory fume hood. Thermal degradation temperature range was 100 - 420 oC and experiment run time was 5 hours. Product fuel density is 0.84 gm/ml an...

Nonlinear estimation and control of automotive drivetrains

CERN Document Server

Chen, Hong

2014-01-01

Nonlinear Estimation and Control of Automotive Drivetrains discusses the control problems involved in automotive drivetrains, particularly in hydraulic Automatic Transmission (AT), Dual Clutch Transmission (DCT) and Automated Manual Transmission (AMT). Challenging estimation and control problems, such as driveline torque estimation and gear shift control, are addressed by applying the latest nonlinear control theories, including constructive nonlinear control (Backstepping, Input-to-State Stable) and Model Predictive Control (MPC). The estimation and control performance is improved while the calibration effort is reduced significantly. The book presents many detailed examples of design processes and thus enables the readers to understand how to successfully combine purely theoretical methodologies with actual applications in vehicles. The book is intended for researchers, PhD students, control engineers and automotive engineers. Hong Chen is a professor at the State Key Laboratory of Automotive Simulation and...

Motion Control of Four-Wheel Independently Actuated Electric Ground Vehicles considering Tire Force Saturations

Directory of Open Access Journals (Sweden)

Rongrong Wang

2013-01-01

Full Text Available A vehicle stability control approach for four-wheel independently actuated (FWIA electric vehicles is presented. The proposed control method consists of a higher-level controller and a lower-level controller. An adaptive control-based higher-level controller is designed to yield the vehicle virtual control efforts to track the desired vehicle motions due to the possible modeling inaccuracies and parametric uncertainties. The lower-level controller considering tire force saturation is given to allocate the required control efforts to the four in-wheel motors for providing the desired tire forces. An analytic method is given to distribute the high-level control efforts, without using the numerical-optimization-based control allocation algorithms. Simulations based on a high-fidelity, CarSim, and full-vehicle model show the effectiveness of the control approach.

Electromechanical Drivetrain Simulation

DEFF Research Database (Denmark)

Gallego Calderon, Juan Felipe

Wind turbines structures are exposed to inclement loading conditions varying from the turbulent wind field to fluctuations in the electric grid. The variation of these conditions, in addition to special events such as emergency stops, has a great impact of the life time of the components. In multi......-MW wind turbines, it is common to find a geared drivetrain, which is the interface between the mechanical and electrical domain. Due to the varying conditions, the drivetrain can suffer accelerated damage reducing the target 20 years life of the turbine. This Ph.D. thesis focuses on the implementation...... to the planet bearings in the planetary stage. In brief, the tool is used for the dynamic analysis of the drive-train components under different loading conditions following certification guidelines. Several numerical simulations demonstrate the capabilities of the tool, and new results show how the lifetime...

78 FR 3843 - Federal Motor Vehicle Safety Standards; New Pneumatic and Certain Specialty Tires

Science.gov (United States)

2013-01-17

... Approval Handbook for Japanese Certification, Safety Regulations for Road Vehicles, Technical Standards For... Technology Transfer and Advancement Act Section 12(d) of the National Technology Transfer and Advancement Act... vehicle safety, Motor vehicles, Rubber and rubber products, and Tires. In consideration of the foregoing...

Haul truck tire dynamics due to tire condition

International Nuclear Information System (INIS)

Anzabi, R Vaghar; Nobes, D S; Lipsett, M G

2012-01-01

Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

Haul truck tire dynamics due to tire condition

Science.gov (United States)

Vaghar Anzabi, R.; Nobes, D. S.; Lipsett, M. G.

2012-05-01

Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

Advanced Gearless Drivetrain - Phase I Technical Report

Energy Technology Data Exchange (ETDEWEB)

Butterfield, Sandy; Smith, Jim; Petch, Derek; Sullivan, Brian; Smith, Peter; Pierce, Kirk

2012-08-31

Boulder Wind Power (BWP) collaborated with the National Renewable Energy Laboratory (NREL) in Golden, Colorado, to demonstrate the economics of scaling an advanced gearless drivetrain technology to 6MW (and larger) turbine applications. The project goal was to show that this advanced drivetrain technology enables a cost of energy of less than $0.10/kWH in offshore applications. This drivetrain technology achieves this Cost of Energy (COE) advantage via a 70% greater torque density versus current state-of-the-art drivetrain technologies. In addition, a new dynamically compliant design strategy is required to optimize turbine system-level COE. The BWP generator is uniquely suited for this new design strategy. This project developed a concept design for a 6MW drivetrain and culminated in a plan for a system-level test of this technology at 3MW scale. The project further demonstrated the advantage of the BWP drivetrain with increasing power ratings, with conceptual designs through 10 MW.

Tool-driven Design and Automated Parameterization for Real-time Generic Drivetrain Models

Directory of Open Access Journals (Sweden)

Schwarz Christina

2015-01-01

Full Text Available Real-time dynamic drivetrain modeling approaches have a great potential for development cost reduction in the automotive industry. Even though real-time drivetrain models are available, these solutions are specific to single transmission topologies. In this paper an environment for parameterization of a solution is proposed based on a generic method applicable to all types of gear transmission topologies. This enables tool-guided modeling by non- experts in the fields of mechanic engineering and control theory leading to reduced development and testing efforts. The approach is demonstrated for an exemplary automatic transmission using the environment for automated parameterization. Finally, the parameterization is validated via vehicle measurement data.

Vehicle Sliding Mode Control with Adaptive Upper Bounds: Static versus Dynamic Allocation to Saturated Tire Forces

Directory of Open Access Journals (Sweden)

Ali Tavasoli

2012-01-01

Full Text Available Nonlinear vehicle control allocation is achieved through distributing the task of vehicle control among individual tire forces, which are constrained to nonlinear saturation conditions. A high-level sliding mode control with adaptive upper bounds is considered to assess the body yaw moment and lateral force for the vehicle motion. The proposed controller only requires the online adaptation of control gains without acquiring the knowledge of upper bounds on system uncertainties. Static and dynamic control allocation approaches have been formulated to distribute high-level control objectives among the system inputs. For static control allocation, the interior-point method is applied to solve the formulated nonlinear optimization problem. Based on the dynamic control allocation method, a dynamic update law is derived to allocate vehicle control to tire forces. The allocated tire forces are fed into a low-level control module, where the applied torque and active steering angle at each wheel are determined through a slip-ratio controller and an inverse tire model. Computer simulations are used to prove the significant effects of the proposed control allocation methods on improving the stability and handling performance. The advantages and limitations of each method have been discussed, and conclusions have been derived.

Advanced Wind Turbine Drivetrain Concepts. Workshop Report

Energy Technology Data Exchange (ETDEWEB)

none,

2010-12-01

This report presents key findings from the Department of Energy’s Advanced Drivetrain Workshop, held on June 29-30, 2010, to assess different advanced drivetrain technologies, their relative potential to improve the state-of-the-art in wind turbine drivetrains, and the scope of research and development needed for their commercialization in wind turbine applications.

Tire Recycling

Science.gov (United States)

1997-01-01

Cryopolymers, Inc. tapped NASA expertise to improve a process for recycling vehicle tires by converting shredded rubber into products that can be used in asphalt road beds, new tires, hoses, and other products. In conjunction with the Southern Technology Applications Center and Stennis Space Center, NASA expertise in cryogenic fuel-handling needed for launch vehicle and spacecraft operations was called upon to improve the recycling concept. Stennis advised Cryopolymers on the type of equipment required, as well as steps to reduce the amount of liquid nitrogen used in the process. They also guided the company to use more efficient ways to control system hardware. It is estimated that more than 300 million tires nationwide are produced per year. Cryopolymers expects to reach a production rate of 5,000 tires recycled per day.

Consumption and efficiency of a passenger car with a hydrogen/oxygen PEFC based hybrid electric drivetrain

Energy Technology Data Exchange (ETDEWEB)

Buechi, F.N.; Dietrich, P.; Tsukada, A.; Koetz, R.; Freunberger, S.A. [Paul Scherrer Institut, Electrochemistry Laboratory, CH-5232 Villigen PSI (Switzerland); Paganelli, G.; Laurent, D.; Varenne, P.; Delfino, A.; Magne, P.A.; Walser, D.; Olsommer, D. [Conception et Developpement Michelin, Route Andre-Piller 30, CH-1762 Givisiez (Switzerland)

2007-08-15

The main factors for reducing the consumption of a vehicle are reduction of curb weight, air drag and increase in the drivetrain efficiency. Highly efficient drivetrains can be developed based on PEFC technology and curb weight may be limited by an innovative vehicle construction. In this paper, data on consumption and efficiency of a four-place passenger vehicle with a curb weight of 850 kg and an H{sub 2}/O{sub 2} fed PEFC/Supercap hybrid electric powertrain are presented. Hydrogen consumption in the New European Driving Cycle is 0.67 kg H{sub 2}/100 km, which corresponds to a gasoline equivalent consumption of 2.5 l/100 km. When including the energy needed to supply pure oxygen, the calculated consumption increases from 0.67 to 0.69-0.79 kg H{sub 2}/100 km, depending on the method of oxygen production. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Mobility potential of a robotic six-wheeled omnidirectional drive vehicle (ODV) with z-axis and tire inflation control

Science.gov (United States)

Witus, Gary

2000-07-01

Robot vehicle mobility is the product of the physical configuration, mechatronics (sensors, actuators, and control) and the motion programs for different obstacles, terrain conditions, and maneuver objectives. This paper examines the mobility potential of a robotic 6-by-6 wheeled omni-directional drive vehicle (ODV) with z-axis and tire inflation control. Ad ODV can steer and drive all wheels independently. The direction of motion is independent of the orientation of the body. Z- axis control refers to independent control of the suspension elevation at each wheel. Pneumatic tire inflation control provides the ability to inflate and deflate individual tires. The paper describes motion programs for various discrete obstacles and challenging terrain conditions. The paper illustrates how ODV control, z-axis control and tire inflation control interact to provide high mobility with respect to cornering, maneuvering on slopes, negotiating vertical step and horizontal gap obstacles, and braking/acceleration on soft soil and slick surfaces. The paper derives guidelines for the physical dimensions of the vehicle needed to achieve these capabilities.

Spring Tire

Science.gov (United States)

Asnani, Vivake M.; Benzing, Jim; Kish, Jim C.

2011-01-01

The spring tire is made from helical springs, requires no air or rubber, and consumes nearly zero energy. The tire design provides greater traction in sandy and/or rocky soil, can operate in microgravity and under harsh conditions (vastly varying temperatures), and is non-pneumatic. Like any tire, the spring tire is approximately a toroidal-shaped object intended to be mounted on a transportation wheel. Its basic function is also similar to a traditional tire, in that the spring tire contours to the surface on which it is driven to facilitate traction, and to reduce the transmission of vibration to the vehicle. The essential difference between other tires and the spring tire is the use of helical springs to support and/or distribute load. They are coiled wires that deform elastically under load with little energy loss.

Demonstration of improved vehicle fuel efficiency through innovative tire design, materials, and weight reduction technologies

Energy Technology Data Exchange (ETDEWEB)

Donley, Tim [Cooper Tire & Rubber Company Incorporated, Findlay, OH (United States)

2014-12-31

Cooper completed an investigation into new tire technology using a novel approach to develop and demonstrate a new class of fuel efficient tires using innovative materials technology and tire design concepts. The objective of this work was to develop a new class of fuel efficient tires, focused on the “replacement market” that would improve overall passenger vehicle fuel efficiency by 3% while lowering the overall tire weight by 20%. A further goal of this project was to accomplish the objectives while maintaining the traction and wear performance of the control tire. This program was designed to build on what has already been accomplished in the tire industry for rolling resistance based on the knowledge and general principles developed over the past decades. Cooper’s CS4 (Figure #1) premium broadline tire was chosen as the control tire for this program. For Cooper to achieve the goals of this project, the development of multiple technologies was necessary. Six technologies were chosen that are not currently being used in the tire industry at any significant level, but that showed excellent prospects in preliminary research. This development was divided into two phases. Phase I investigated six different technologies as individual components. Phase II then took a holistic approach by combining all the technologies that showed positive results during phase one development.

Design of a Portable Tire Test Rig and Vehicle Roll-Over Stability Control

OpenAIRE

Fox, Derek Martin

2009-01-01

Vehicle modeling and simulation have fast become the easiest and cheapest method for vehicle testing. No longer do multiple, intensive, physical tests need be performed to analyze the performance parameters that one wishes to validate. One component of the vehicle simulation that is crucial to the correctness of the result is the tire. Simulations that are run by a computer can be run many times faster than a real test could be performed, so the cost and complexity of the testing is reduced....

Measurement of Vehicle-Bridge-Interaction force using dynamic tire pressure monitoring

Science.gov (United States)

Chen, Zhao; Xie, Zhipeng; Zhang, Jian

2018-05-01

The Vehicle-Bridge-Interaction (VBI) force, i.e., the normal contact force of a tire, is a key component in the VBI mechanism. The VBI force measurement can facilitate experimental studies of the VBI as well as input-output bridge structural identification. This paper introduces an innovative method for calculating the interaction force by using dynamic tire pressure monitoring. The core idea of the proposed method combines the ideal gas law and a basic force model to build a relationship between the tire pressure and the VBI force. Then, unknown model parameters are identified by the Extended Kalman Filter using calibration data. A signal filter based on the wavelet analysis is applied to preprocess the effect that the tire rotation has on the pressure data. Two laboratory tests were conducted to check the proposed method's validity. The effects of different road irregularities, loads and forward velocities were studied. Under the current experiment setting, the proposed method was robust to different road irregularities, and the increase in load and velocity benefited the performance of the proposed method. A high-speed test further supported the use of this method in rapid bridge tests. Limitations of the derived theories and experiment were also discussed.

A structured model library for the analysis of electric-vehicle drivetrains; Eine strukturierte Modellbibliothek fuer Analysen an Antriebsstraengen von Elektrofahrzeugen

Energy Technology Data Exchange (ETDEWEB)

Niedzwiedz, Simon; Frei, Stephan [Technische Univ. Dortmund (Germany). AG Bordsysteme

2012-11-01

This contribution presents a concept for developing structured simulation model libraries. The main objectives are securing a reliable functionality of the contained models among each other and meeting the requirements that a model library has to be flexible and easy to manage on one side, while it has to define a comprehensible and distinct order on the other side. These qualities are especially important in bigger or distributed working groups, for ensuring a long-term and efficient usability. For model reusability and continuous further development a consistent structuring is essential. This concept will be exemplified through a structured model library for the analysis of electric-vehicle drivetrains. (orig.)

NREL-Prime Next-Generation Drivetrain Dynamometer Test Report

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Erdman, Bill [Cinch, Inc., Moraga, CA (United States); Blodgett, Douglas [DNV KEMA Renewables, Burlington, VT (United States); Halse, Christopher [Romax Technology, Boulder, CO (United States)

2016-08-01

Advances in wind turbine drivetrain technologies are necessary to improve reliability and reduce the cost of energy for land-based and offshore wind turbines. The NREL-Prime Next-Generation Drivetrain team developed a geared, medium-speed drivetrain that is lighter, more reliable and more efficient than existing designs. One of the objectives of Phase II of the project was to complete the detailed design, fabrication, and dynamometer testing of a 750 kilowatt (kW) drivetrain that includes the key gearbox innovations designed by Romax Technology and power converter innovations designed by DNV Kema Renewables. The purpose of this document is to summarize these tests completed in NREL's National Wind Technology Center 2.5 megawatt (MW) dynamometer.

Next Generation Drivetrain Development and Test Program

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan; Erdman, Bill; Blodgett, Doug; Halse, Chris; Grider, Dave

2015-11-03

This presentation was given at the Wind Energy IQ conference in Bremen, Germany, November 30 through December 2, 2105. It focused on the next-generation drivetrain architecture and drivetrain technology development and testing (including gearbox and inverter software and medium-voltage inverter modules.

Vehicle Tire and Wheel Creation in BRL-CAD

Science.gov (United States)

2009-04-01

Tire Tread Modeling 4  4.  Setting Tire Thickness 7  5.  Changing the Rim Width 9  6.  Changing the Radial Location of the... treaded or nontreaded model in the tire -model.c combination based on the analysis. 4. Setting Tire Thickness Tire thickness is manipulated via... tread is not modeled by default but can be added using options. • Fine-grained control of parameters such as tire thickness is available with

Evaluation of Tire/Surfacing/Base Contact Stresses and Texture Depth

Directory of Open Access Journals (Sweden)

W.J.vdM. Steyn

2015-03-01

Full Text Available Tire rolling resistance has a major impact on vehicle fuel consumption. Rolling resistance is the loss of energy due to the interaction between the tire and the pavement surface. This interaction is a complicated combination of stresses and strains which depend on both tire and pavement related factors. These include vehicle speed, vehicle weight, tire material and type, road camber, tire inflation pressure, pavement surfacing texture etc. In this paper the relationship between pavement surface texture depth and tire/surfacing contact stress and area is investigated. Texture depth and tire/surfacing contact stress were measured for a range of tire inflation pressures on five different pavement surfaces. In the analysis the relationship between texture and the generated contact stresses as well as the contact stress between the surfacing and base layer are presented and discussed, and the anticipated effect of these relationships on the rolling resistance of vehicles on the surfacings, and subsequent vehicle fuel economy discussed.

Wheels and Tires: Understanding the Numbers on the Sides of Tires Might Lead to Longer Life Tires and Improved Driving Safety

Science.gov (United States)

Ritz, John M.

2005-01-01

Automotive wheels and tires require knowledge to understand their specifications and use. While the durability and useful life of tires have increased substantially over the last several decades, in all probability consumers will purchase a number of vehicle tires over their lifetime. Knowing how they are made and what the numbers mean will assist…

Electromechanical Drivetrain Simulation

DEFF Research Database (Denmark)

Gallego-Calderon, Juan; Branner, Kim; Natarajan, Anand

2013-01-01

The work presented in this paper is another step from the DTU Wind Energy efforts to advance understanding of the electromechanical drive-train loads and its interaction with the rest of the components in the wind turbine. The main objective of the PhD is to investigate the modelling and simulation...... flexibilities, the generator dynamics and the grid, along with the structural loads in the wind turbine. In this paper, two simulation approaches are presented and conclusions are made according to their advantages and disadvantages. The drive-train is described by means of a torsional model composed...... of the main shaft, gearbox and generator. Special attention is given to the modelling of the gearbox and the generator in order to study the mechanical vibrations caused by turbulent wind and grid dynamics....

3 CFR - Imports of Certain Passenger Vehicle and Light Truck Tires From the People's Republic of China

Science.gov (United States)

2010-01-01

... vehicle and light truck tires from the People's Republic of China (China) are being imported into the... 3 The President 1 2010-01-01 2010-01-01 false Imports of Certain Passenger Vehicle and Light Truck... Presidential Determination No. 2009-28 of September 11, 2009 Imports of Certain Passenger Vehicle and Light...

Deterministic and Stochastic Semi-Empirical Transient Tire Models

OpenAIRE

Umsrithong, Anake

2012-01-01

The tire is one of the most important components of the vehicle. It has many functions, such as supporting the load of the vehicle, transmitting the forces which drive, brake and guide the vehicle, and acting as the secondary suspension to absorb the effect of road irregularities before transmitting the forces to the vehicle suspension. A tire is a complex reinforced rubber composite air container. The structure of the tire is very complex. It consists of several layers of synthetic polymer, ...

Simulation and control of an automotive dry clutch

NARCIS (Netherlands)

Serrarens, A.F.A.; Dassen, M.; Steinbuch, M.

2004-01-01

In this paper the dynamic behavior and control of an automotive dry clutch is analyzed. Thereto, a straight-forward model of the clutch is embedded within a dynamic model of an automotive powertrain comprising an internal combustion engine, drivetrain and wheels moving a vehicle through tire-road

A novel integrated approach for path following and directional stability control of road vehicles after a tire blow-out

Science.gov (United States)

Wang, Fei; Chen, Hong; Guo, Konghui; Cao, Dongpu

2017-09-01

The path following and directional stability are two crucial problems when a road vehicle experiences a tire blow-out or sudden tire failure. Considering the requirement of rapid road vehicle motion control during a tire blow-out, this article proposes a novel linearized decoupling control procedure with three design steps for a class of second order multi-input-multi-output non-affine system. The evaluating indicators for controller performance are presented and a performance related control parameter distribution map is obtained based on the stochastic algorithm which is an innovation for non-blind parameter adjustment in engineering implementation. The analysis on the robustness of the proposed integrated controller is also performed. The simulation studies for a range of driving conditions are conducted, to demonstrate the effectiveness of the proposed controller.

30 CFR 57.14104 - Tire repairs.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tire repairs. 57.14104 Section 57.14104 Mineral... Devices and Maintenance Requirements § 57.14104 Tire repairs. (a) Before a tire is removed from a vehicle for tire repair, the valve core shall be partially removed to allow for gradual deflation and then...

30 CFR 56.14104 - Tire repairs.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tire repairs. 56.14104 Section 56.14104 Mineral... Devices and Maintenance Requirements § 56.14104 Tire repairs. (a) Before a tire is removed from a vehicle for tire repair, the valve core shall be partially removed to allow for gradual deflation and then...

Pneumatic Tire Performance on Ice

OpenAIRE

Kishore Bhoopalam, Anudeep

2015-01-01

The evolution of vehicle safety systems, from the earliest brakes to today's accident avoidance systems, has led vehicles to have very high passenger safety. Driving on ice, though, still happens to be one of the driving conditions of low safety. A multitude of factors were identified by various studies to contribute to the complex frictional mechanism at the tire-ice interface. The tire is only force transmitting element of the vehicle, to the surface. Thus it is very essential to have in de...

Wind Turbine Drivetrain Reliability Collaborative Workshop: A Recap

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sheng, Shuangwen [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cotrell, Jason [National Renewable Energy Lab. (NREL), Golden, CO (United States); Greco, Aaron [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-08-01

The Wind Turbine Drivetrain Reliability Collaborative Workshop was convened by the National Renewable Energy Laboratory (NREL), Argonne National Laboratory, and the U.S. Department of Energy to explore the state of the art in wind turbine drivetrain mechanical system reliability as well as research and development (R&D) challenges that if solved could have significant benefits. The workshop was held at the Research Support Facility on NREL's main campus in Golden, Colorado, from February 16-17, 2016. More than 120 attendees participated from industry, academia, and government. Plenary presentations covered wind turbine drivetrain design, testing, and analysis; tribology -- the science and engineering of interacting surfaces in relative motion -- and failure modes; and condition monitoring and data analytics. In addition to the presentations, workshops were held in each of these areas to discuss R&D challenges. This report serves as a summary of the presentations, workshops, and conclusions on R&D challenges in wind turbine drivetrain reliability.

Analysis of the vibration of the vehicle body with the elimination of the influence of tires

Directory of Open Access Journals (Sweden)

Łukasz KONIECZNY

2015-09-01

Full Text Available The article presented the results of vibration measurements of selected elements of the vehicle during the test vibration carried out on a bench with a harmonic kinematic extortion. The results of research carried out for the car when replacing tire and wheels steel tripod eliminating the influence of elasticity and damping tires. The tests were performed at various values of the shock absorber fluid filling (from 100% to 50% of the shock absorber fluid. For registered vibration acceleration STFT analysis was performed.

Advanced Wind Turbine Drivetrain Concepts: Workshop Report, June 29-30, 2010

Energy Technology Data Exchange (ETDEWEB)

DOE, EERE

2010-12-01

This report presents key findings from the Department of Energy's Advanced Drivetrain Workshop, held on June 29-30, 2010 in Broomfield, Colorado, to assess different advanced drivetrain technologies, their relative potential to improve the state-of-the-art in wind turbine drivetrains, and the scope of research and development needed for their commercialization in wind turbine applications.

3rd symposium on tires and chassis; 3. Symposium Reifen und Fahrwerk

Energy Technology Data Exchange (ETDEWEB)

Geringer, B.; Stumpf, H. (comps.)

2005-07-01

The present volume contains the talks, which were held at the 3rd symposium on ''Tires and chassis'' at the Institute for combustion machines at the Technical University Vienna on 26th September 2005 in cooperation with UAMTTC and Semperit Reifen Ges.m.H. Apart from technical improvements on chassis, tires and carriageway the overall perspective will get more important in the future, which also includes the driver, the neighbour, the environment and the traffic policy. Due to an increasing number of international participants, discussions can be expected, which will take into consideration extraordinary and manifold perspectives. The third symposium on ''Tires and chassis'' discusses the following developments, of which some are evolutionary. (a) Tire engineering; environmental aspects of tires, roll resistance of tires, driving comfort of tires, winter tires for passenger vehicles and trucks. (b) vehicle engineering, engineering of a race car chassis by means of telemetric measuring data acquisition; simulation of steering wheel vibrations on a complete vehicle test stand. (c) Vehicle steering; chassis of tracklaying vehicles; automatic air pressure control. (orig.)

Evaluation of the tire pressure influence on the lateral forces that occur between tire and road

Science.gov (United States)

Cordoş, N.; Todoruţ, A.; Barabás, I.

2017-10-01

The main objective of the paper is to capture the behavior of a vehicle on a race circuit, depending on the different inflation pressures of the tires (underpressure and overpressure). Taking into account that in the cornering the forces and the moments of inertia rise due the vehicle mass, and an inertial force decomposes in two components, one in the longitudinal plane and one in the transverse plane, the work aims the assessing the lateral forces that appear, to the contact between the tires and the tread, depending on the inflation pressure. The results have a graphic interpretation, enabling a comparative study of them. Results have been obtained regarding the lateral tire forces that occur between the tire and the road. The differences between these forces were particularly noticeable in cornering, and the differences between these forces were interpreted according to the tire inflation pressure.

40 CFR 202.23 - Visual tire inspection.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Visual tire inspection. 202.23 Section... Visual tire inspection. No motor carrier subject to these regulations shall at any time operate any motor vehicle of a type to which this regulation is applicable on a tire or tires having a tread pattern which...

Estimation of tire characteristics by concerning test data of vehicles; Jidosha no senkai shiken data ni yoru dire tokusei no suisan

Energy Technology Data Exchange (ETDEWEB)

Nakamura, M; Sekine, T; Nagae, H [Nihon University, Tokyo (Japan)

1997-10-01

To study and/or develop the vehicle motion of a braking in turns theoretically, the cornering characteristics of the tire under the action of braking forces must be required. On the other hand, such data are very few to be published and also there be few tire testing machine to be able to use. The authors tried to derive such data from the vehicle behaviors in steady turns and braking in turns. Because each wheel loads are unknown factors, the two wheeled vehicle model are employed in analysis. The methodology of analysis and the reasonable results are presented in this paper. 5 refs., 10 figs., 2 tabs.

Stochastic Models of Defects in Wind Turbine Drivetrain Components

DEFF Research Database (Denmark)

Rafsanjani, Hesam Mirzaei; Sørensen, John Dalsgaard

2013-01-01

The drivetrain in a wind turbine nacelle typically consists of a variety of heavily loaded components, like the main shaft, bearings, gearbox and generator. The variations in environmental load challenge the performance of all the components of the drivetrain. Failure of each of these components...

Research on Hybrid Vehicle Drivetrain

Science.gov (United States)

Xie, Zhongzhi

Hybrid cars as a solution to energy saving, emission reduction measures, have received widespread attention. Motor drive system as an important part of the hybrid vehicles as an important object of study. Based on the hybrid electric vehicle powertrain control system for permanent magnet synchronous motor as the object of study. Can be applied to hybrid car compares the characteristics of traction motors, chose permanent magnet synchronous Motors as drive motors for hybrid vehicles. Building applications in hybrid cars in MATLAB/Simulink simulation model of permanent-magnet synchronous motor speed control system and analysis of simulation results.

Improving Wind Turbine Drivetrain Reliability Using a Combined Experimental, Computational, and Analytical Approach

Energy Technology Data Exchange (ETDEWEB)

Guo, Y.; van Dam, J.; Bergua, R.; Jove, J.; Campbell, J.

2015-03-01

Nontorque loads induced by the wind turbine rotor overhang weight and aerodynamic forces can greatly affect drivetrain loads and responses. If not addressed properly, these loads can result in a decrease in gearbox component life. This work uses analytical modeling, computational modeling, and experimental data to evaluate a unique drivetrain design that minimizes the effects of nontorque loads on gearbox reliability: the Pure Torque(R) drivetrain developed by Alstom. The drivetrain has a hub-support configuration that transmits nontorque loads directly into the tower rather than through the gearbox as in other design approaches. An analytical model of Alstom's Pure Torque drivetrain provides insight into the relationships among turbine component weights, aerodynamic forces, and the resulting drivetrain loads. Main shaft bending loads are orders of magnitude lower than the rated torque and are hardly affected by wind conditions and turbine operations.

A Tire Model for Off-Highway Vehicle Simulation on Short Wave Irregular Terrain

DEFF Research Database (Denmark)

Langer, Thomas Heegaard; Kristensen, Lars B; Mouritsen, Ole Ø.

2010-01-01

Manufacturers of construction machinery are challenged in several ways concerning dynamic loads. Considering off-highway dump trucks that travel through high amplitude short wave irregular terrain with considerable speed two aspects concerning dynamics are important. The first is the legal...... between simulated data and experimental data obtained from full vehicle testing. The experimental work is carried out by letting a dump truck pass a set of well defined obstacles. Based on the obtained agreement between simulated and measured results the tire model is considered suitable for describing...... joints, spring-damper elements and the welded structures it is crucial to have information on the time history of the loads. For trucks carrying payloads the most important load contribution is undoubtedly the reaction forces between terrain and tires. By use of virtual prototypes it is possible...

Tire-road friction estimation and traction control strategy for motorized electric vehicle

Science.gov (United States)

Jin, Li-Qiang; Yue, Weiqiang

2017-01-01

In this paper, an optimal longitudinal slip ratio system for real-time identification of electric vehicle (EV) with motored wheels is proposed based on the adhesion between tire and road surface. First and foremost, the optimal longitudinal slip rate torque control can be identified in real time by calculating the derivative and slip rate of the adhesion coefficient. Secondly, the vehicle speed estimation method is also brought. Thirdly, an ideal vehicle simulation model is proposed to verify the algorithm with simulation, and we find that the slip ratio corresponds to the detection of the adhesion limit in real time. Finally, the proposed strategy is applied to traction control system (TCS). The results showed that the method can effectively identify the state of wheel and calculate the optimal slip ratio without wheel speed sensor; in the meantime, it can improve the accelerated stability of electric vehicle with traction control system (TCS). PMID:28662053

77 FR 11189 - Yokohama Tire Corporation, Denial of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-02-24

...-0056; Notice 2] Yokohama Tire Corporation, Denial of Petition for Decision of Inconsequential... Inconsequential Noncompliance. SUMMARY: Yokohama Tire Corporation, (YTC),\\1\\ replacement tires for passenger cars... Federal Motor Vehicle Safety Standard (FMVSS) No. 139, New Pneumatic Radial Tires for Light Vehicles. YTC...

An Analytical Tire Model with Flexible Carcass for Combined Slips

Directory of Open Access Journals (Sweden)

Nan Xu

2014-01-01

Full Text Available The tire mechanical characteristics under combined cornering and braking/driving situations have significant effects on vehicle directional controls. The objective of this paper is to present an analytical tire model with flexible carcass for combined slip situations, which can describe tire behavior well and can also be used for studying vehicle dynamics. The tire forces and moments come mainly from the shear stress and sliding friction at the tread-road interface. In order to describe complicated tire characteristics and tire-road friction, some key factors are considered in this model: arbitrary pressure distribution; translational, bending, and twisting compliance of the carcass; dynamic friction coefficient; anisotropic stiffness properties. The analytical tire model can describe tire forces and moments accurately under combined slip conditions. Some important properties induced by flexible carcass can also be reflected. The structural parameters of a tire can be identified from tire measurements and the computational results using the analytical model show good agreement with test data.

A Novel Strain-Based Method to Estimate Tire Conditions Using Fuzzy Logic for Intelligent Tires

Directory of Open Access Journals (Sweden)

Daniel Garcia-Pozuelo

2017-02-01

Full Text Available The so-called intelligent tires are one of the most promising research fields for automotive engineers. These tires are equipped with sensors which provide information about vehicle dynamics. Up to now, the commercial intelligent tires only provide information about inflation pressure and their contribution to stability control systems is currently very limited. Nowadays one of the major problems for intelligent tire development is how to embed feasible and low cost sensors to obtain reliable information such as inflation pressure, vertical load or rolling speed. These parameters provide key information for vehicle dynamics characterization. In this paper, we propose a novel algorithm based on fuzzy logic to estimate the mentioned parameters by means of a single strain-based system. Experimental tests have been carried out in order to prove the suitability and durability of the proposed on-board strain sensor system, as well as its low cost advantages, and the accuracy of the obtained estimations by means of fuzzy logic.

The prediction of airborne and structure-borne noise potential for a tire

Science.gov (United States)

Sakamoto, Nicholas Y.

Tire/pavement interaction noise is a major component of both exterior pass-by noise and vehicle interior noise. The current testing methods for ranking tires from loud to quiet require expensive equipment, multiple tires, and/or long experimental set-up and run times. If a laboratory based off-vehicle test could be used to identify the airborne and structure-borne potential of a tire from its dynamic characteristics, a relative ranking of a large group of tires could be performed at relatively modest expense. This would provide a smaller sample set of tires for follow-up testing and thus save expense for automobile OEMs. The focus of this research was identifying key noise features from a tire/pavement experiment. These results were compared against a stationary tire test in which the natural response of the tire to a forced input was measured. Since speed was identified as having some effect on the noise, an input function was also developed to allow the tires to be ranked at an appropriate speed. A relative noise model was used on a second sample set of tires to verify if the ranking could be used against interior vehicle measurements. While overall level analysis of the specified spectrum had mixed success, important noise generating features were identified, and the methods used could be improved to develop a standard off-vehicle test to predict a tire's noise potential.

Flatness based feedforward control of a parallel hybrid drivetrain; Flachheitsbasierter Vorsteuerungsentwurf fuer den Antriebsstrang eines Parallelhybriden

Energy Technology Data Exchange (ETDEWEB)

Gasper, Rainer; Hesseler, Frank; Abel, Dirk [RWTH Aachen Univ. (Germany). Inst. fuer Regelungstechnik

2010-10-15

The advantages of Hybrid Electrical Vehicles (HEV) are fuel consumption reduction and minimization of exhaust emissions. Moreover, the drivability of a HEV is very important for the consumer acceptance. The gear shifts and the start of the internal combustion engine are very important for the drivability of a HEV. Because this two tasks are automated, oscillations in the vehicle would be uncomfortable for the driver. In the paper at hand, feedforward controllers for the drivetrain control of a parallel hybrid with an automated manual transmission and a dry clutch are presented. (orig.)

Research overview : design specifications for hybrid vehicles

NARCIS (Netherlands)

Hofman, T.; Druten, van R.M.

2004-01-01

In this paper a method is proposed for determination of the design specifications regarding the energy exchange systems for different chargesustaining hybrid vehicles of different vehicle classes. Hybrid drivetrains for vehicles combine multiple power sources in order to increase the driving

Indirect Tire Monitoring System - Machine Learning Approach

Science.gov (United States)

Svensson, O.; Thelin, S.; Byttner, S.; Fan, Y.

2017-10-01

The heavy vehicle industry has today no requirement to provide a tire pressure monitoring system by law. This has created issues surrounding unknown tire pressure and thread depth during active service. There is also no standardization for these kind of systems which means that different manufacturers and third party solutions work after their own principles and it can be hard to know what works for a given vehicle type. The objective is to create an indirect tire monitoring system that can generalize a method that detect both incorrect tire pressure and thread depth for different type of vehicles within a fleet without the need for additional physical sensors or vehicle specific parameters. The existing sensors that are connected communicate through CAN and are interpreted by the Drivec Bridge hardware that exist in the fleet. By using supervised machine learning a classifier was created for each axle where the main focus was the front axle which had the most issues. The classifier will classify the vehicles tires condition and will be implemented in Drivecs cloud service where it will receive its data. The resulting classifier is a random forest implemented in Python. The result from the front axle with a data set consisting of 9767 samples of buses with correct tire condition and 1909 samples of buses with incorrect tire condition it has an accuracy of 90.54% (0.96%). The data sets are created from 34 unique measurements from buses between January and May 2017. This classifier has been exported and is used inside a Node.js module created for Drivecs cloud service which is the result of the whole implementation. The developed solution is called Indirect Tire Monitoring System (ITMS) and is seen as a process. This process will predict bad classes in the cloud which will lead to warnings. The warnings are defined as incidents. They contain only the information needed and the bandwidth of the incidents are also controlled so incidents are created within an

The prediction of airborne and structure-borne noise potential for a tire

OpenAIRE

Sakamoto, Nicholas

2014-01-01

Tire/pavement interaction noise is a major component of both exterior pass-by noise and vehicle interior noise. The current testing methods for ranking tires from loud to quiet require expensive equipment, multiple tires, and/or long experimental set-up and run times. If a laboratory based off-vehicle test could be used to identify the airborne and structure-borne potential of a tire from its dynamic characteristics, a relative ranking of a large group of tires could be performed at relativel...

Wind Turbine Drivetrain Condition Monitoring During GRC Phase 1 and Phase 2 Testing

Energy Technology Data Exchange (ETDEWEB)

Sheng, S.; Link, H.; LaCava, W.; van Dam, J.; McNiff, B.; Veers, P.; Keller, J.; Butterfield, S.; Oyague, F.

2011-10-01

This report will present the wind turbine drivetrain condition monitoring (CM) research conducted under the phase 1 and phase 2 Gearbox Reliability Collaborative (GRC) tests. The rationale and approach for this drivetrain CM research, investigated CM systems, test configuration and results, and a discussion on challenges in wind turbine drivetrain CM and future research and development areas, will be presented.

A hierarchical estimator development for estimation of tire-road friction coefficient.

Directory of Open Access Journals (Sweden)

Xudong Zhang

Full Text Available The effect of vehicle active safety systems is subject to the friction force arising from the contact of tires and the road surface. Therefore, an adequate knowledge of the tire-road friction coefficient is of great importance to achieve a good performance of these control systems. This paper presents a tire-road friction coefficient estimation method for an advanced vehicle configuration, four-motorized-wheel electric vehicles, in which the longitudinal tire force is easily obtained. A hierarchical structure is adopted for the proposed estimation design. An upper estimator is developed based on unscented Kalman filter to estimate vehicle state information, while a hybrid estimation method is applied as the lower estimator to identify the tire-road friction coefficient using general regression neural network (GRNN and Bayes' theorem. GRNN aims at detecting road friction coefficient under small excitations, which are the most common situations in daily driving. GRNN is able to accurately create a mapping from input parameters to the friction coefficient, avoiding storing an entire complex tire model. As for large excitations, the estimation algorithm is based on Bayes' theorem and a simplified "magic formula" tire model. The integrated estimation method is established by the combination of the above-mentioned estimators. Finally, the simulations based on a high-fidelity CarSim vehicle model are carried out on different road surfaces and driving maneuvers to verify the effectiveness of the proposed estimation method.

A hierarchical estimator development for estimation of tire-road friction coefficient.

Science.gov (United States)

Zhang, Xudong; Göhlich, Dietmar

2017-01-01

The effect of vehicle active safety systems is subject to the friction force arising from the contact of tires and the road surface. Therefore, an adequate knowledge of the tire-road friction coefficient is of great importance to achieve a good performance of these control systems. This paper presents a tire-road friction coefficient estimation method for an advanced vehicle configuration, four-motorized-wheel electric vehicles, in which the longitudinal tire force is easily obtained. A hierarchical structure is adopted for the proposed estimation design. An upper estimator is developed based on unscented Kalman filter to estimate vehicle state information, while a hybrid estimation method is applied as the lower estimator to identify the tire-road friction coefficient using general regression neural network (GRNN) and Bayes' theorem. GRNN aims at detecting road friction coefficient under small excitations, which are the most common situations in daily driving. GRNN is able to accurately create a mapping from input parameters to the friction coefficient, avoiding storing an entire complex tire model. As for large excitations, the estimation algorithm is based on Bayes' theorem and a simplified "magic formula" tire model. The integrated estimation method is established by the combination of the above-mentioned estimators. Finally, the simulations based on a high-fidelity CarSim vehicle model are carried out on different road surfaces and driving maneuvers to verify the effectiveness of the proposed estimation method.

Empirical Analysis of Pneumatic Tire Friction on Ice

OpenAIRE

Holley, Troy Nigel

2010-01-01

Pneumatic tire friction on ice is an under-researched area of tire mechanics. This study covers the design and analysis of a series of pneumatic tire tests on a flat-level ice road surface. The terramechanics rig of the Advanced Vehicle Dynamics Lab (AVDL) is a single-wheel test rig that allows for the experimental analysis of the forces and moments on a tire, providing directly the data for the drawbar pull of said tire, thus supporting the calculation of friction based on this data. This...

A Strain-Based Method to Detect Tires' Loss of Grip and Estimate Lateral Friction Coefficient from Experimental Data by Fuzzy Logic for Intelligent Tire Development.

Science.gov (United States)

Yunta, Jorge; Garcia-Pozuelo, Daniel; Diaz, Vicente; Olatunbosun, Oluremi

2018-02-06

Tires are a key sub-system of vehicles that have a big responsibility for comfort, fuel consumption and traffic safety. However, current tires are just passive rubber elements which do not contribute actively to improve the driving experience or vehicle safety. The lack of information from the tire during driving gives cause for developing an intelligent tire. Therefore, the aim of the intelligent tire is to monitor tire working conditions in real-time, providing useful information to other systems and becoming an active system. In this paper, tire tread deformation is measured to provide a strong experimental base with different experiments and test results by means of a tire fitted with sensors. Tests under different working conditions such as vertical load or slip angle have been carried out with an indoor tire test rig. The experimental data analysis shows the strong relation that exists between lateral force and the maximum tensile and compressive strain peaks when the tire is not working at the limit of grip. In the last section, an estimation system from experimental data has been developed and implemented in Simulink to show the potential of strain sensors for developing intelligent tire systems, obtaining as major results a signal to detect tire's loss of grip and estimations of the lateral friction coefficient.

Tire Models for Use in Braking Applications

OpenAIRE

Svendenius, Jacob

2003-01-01

The tire is a significant part for control of a vehicle. For a well-working brake system the contact properties between the tire and the ground is the limiting factor for a safe braking. To get optimal performance it is important that the system can utilize all friction resources. The brush tire model was a popular method in the 1960's and 1970's before the empirical approaches became dominating. The brush model gives an educational interpretation of the physics behind the tire behavi...

Technology updates from the OEMs (tires, rims, automation inflation systems, and alternative fuels for heavy vehicles)

Energy Technology Data Exchange (ETDEWEB)

White, N. [Charonic Canada Inc., Ottawa, ON (Canada)

2001-07-01

This power point presentation outlined a project at Charonic Canada Inc., which demonstrated and evaluated innovations in the areas of vehicle safety, operating economy and diesel fuel substitution. It also presented a range of results that demonstrate some of the trends that may be used on vehicles, particularly trucks, in the near future. The demonstration involved a 2 year observation of a five truck fleet hauling refuse from Toronto to Michigan. The trucks completed 2,500 round trips of 540 miles and used 115 tonnes of natural gas fuel replacing diesel fuel. Safety innovations included tire pressure monitoring, hazard locator radar system, anti-spray system, wheel nut and bearing temperature indicators and brake safe indicators. These features were reported as being worthwhile investments. Economy innovations included a dual-fuel engine system, wide base tires, light weight CNG tanks, centrifugal oil cleaner and an oil and lubrication system. Although the technology continues to improve, the dual-engine system requires further work. Difficulties were encountered when trying to meet performance, fuel economy and emission targets at the same time. 18 figs.

Assessment of U.S. Manufacturing Capability for Next-Generation Wind Turbine Drivetrains

Energy Technology Data Exchange (ETDEWEB)

Cotrell, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Stelhy, T. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-09-01

Robust U.S. wind turbine manufacturing capabilities and supply chains are important for the United States to reduce the cost of electricity generated from wind turbines. These capabilities and supply chains are also critical to the invention and commercialization of new wind turbine technologies while providing high-quality jobs. The development of advanced drivetrain technologies for windturbine applications is advancing the state of the art for drivetrain design by producing higher capacity and operating reliability than conventional drivetrains. Advanced drivetrain technologies such as medium-speed and direct-drive generators, silicon-carbide (SiC) IGBT-based power electronics, and high torque density speed increasers require different manufacturing and supply chaincapabilities that present both risks and opportunities for U.S. wind turbine manufacturers and the wind industry as a whole. The primary objective of this project is to assess how advanced drivetrain technologies and trends will impact U.S. wind turbine manufacturing and its supply chains. The U.S. Department of Energy and other industry participants will use the information from this study toidentify domestic manufacturing gaps, barriers, and opportunities for developing U.S. wind turbine manufacturing capabilities and supply chains for next-generation drivetrain technologies. This report also includes recommendations for prioritizing technology areas for possible investments by public, private, or nonprofit entities that will reduce the cost of wind-generated electricity. Suchinvestments foster opportunities to invent and commercialize new wind turbine technologies, and provide high-quality jobs in the United States.

A Synthesis on the Evolution of the Studded Tire

National Research Council Canada - National Science Library

Angerinos, Michael

1998-01-01

Ever since studded tires were flrst introduced, the advantages, disadvantages, and effects of studded tires on vehicles, drivers and pavement systems has been the center of research and controversy...

Intelligent tires for identifying coefficient of friction of tire/road contact surfaces using three-axis accelerometer

International Nuclear Information System (INIS)

Matsuzaki, Ryosuke; Kamai, Kazuto; Seki, Ryosuke

2015-01-01

Intelligent tires equipped with sensors as well as the monitoring of the tire/road contact conditions are in demand for improving vehicle control and safety. With the aim of identifying the coefficient of friction of tire/road contact surfaces during driving, including during cornering, we develop an identification scheme for the coefficient of friction that involves estimation of the slip angle and applied force by using a single lightweight three-axis accelerometer attached on the inner surface of the tire. To validate the developed scheme, we conduct tire-rolling tests using an accelerometer-equipped tire with various slip angles on various types of road surfaces, including dry and wet surfaces. The results of these tests confirm that the estimated slip angle and applied force are reasonable. Furthermore, the identified coefficient of friction by the developed scheme agreed with that measured by standardized tests. (paper)

NREL Next Generation Drivetrain: Mechanical Design and Test Plan (Poster)

Energy Technology Data Exchange (ETDEWEB)

Keller, J.; Halse, C.

2014-05-01

The Department of Energy and industry partners are sponsoring a $3m project for design and testing of a 'Next Generation' wind turbine drivetrain at the National Renewable Energy Laboratory (NREL). This poster focuses on innovative aspects of the gearbox design, completed as part of an end-to-end systems engineering approach incorporating innovations that increase drivetrain reliability, efficiency, torque density and minimize capital cost.

In-plane Tire Deformation Measurement Using a Multi-Laser Sensor System

OpenAIRE

Xiong, Yi

2016-01-01

The interactions between tires and roads are basic mechanisms that alter the dynamic states of vehicles. A fundamental understanding of tire-road interactions is clearly demanded in tire design to achieve performance improvements. The emergence of various tire sensors provides an opportunity to make accurate measurement of the physical quantities that are involved in tire-road interactions.  This thesis aims to measure and analyze the in-plane deformation of rolling tires through its direc...

Longitudinal tire force estimation based on sliding mode observer

Energy Technology Data Exchange (ETDEWEB)

El Hadri, A.; Cadiou, J.C.; M' Sirdi, N.K. [Versailles Univ., Paris (France). Lab. de Robotique; Beurier, G.; Delanne, Y. [Lab. Central des Ponts, Centre de Nantes (France)

2001-07-01

This paper presents an estimation method for vehicle longitudinal dynamics, particularly the tractive/braking force. The estimation can be used to detect a critical driving situation to improve security. It can be used also in several vehicle control systems. The main characteristics of the vehicle longitudinal dynamics were taken into account in the model used to design an observer and computer simulations. The state variables are the angular wheel velocity, vehicle velocity and the longitudinal tire force. The proposed differential equation of the tractive/braking force is derived using the concept of relaxation length. The observer designed is based on the sliding mode approach using only the angular wheel velocity measurement. The proposed method of estimation is verified through a one-wheel simulation model with a ''Magic formula'' tire model. Simulations results show an excellent reconstruction of the tire force. (orig.)

Riding on air: critical safety information for you and your tires

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This booklet is issued for public distribution by Transport Canada. It provides a few simple tips concerning automobile tire safety which, if followed, is expected to result in increased personal and vehicle safety, improved fuel economy, prolonged tire life, energy savings and reduced environmental pollution. The information provided include tips about tire pressure, tire inspection for damage and wear, rotation of tires for more even wear, replacing worn tires, the advantages of using snow tires in winter and an explanation of the meaning of the information found on the tire sidewall.

Studded and unstudded winter tires in fatal road accidents in Finland.

Science.gov (United States)

Malmivuo, Mikko; Luoma, Juha; Porthin, Markus

2017-07-04

The aim of the study was to compare the safety effects of studded and unstudded winter tires based on fatal road accidents. The data included 958 road accidents involving a passenger car or van that occurred in Finland from November to March between 1997 and 2012. Comparing the proportions of winter tire type in accidents and in general traffic showed that the overall effect of tire type on the number of accidents was not significant, although studded tires reduced fatal accidents by 10-15%. Compared to unstudded tires, studded tires reduced accidents significantly only on bald ice in 2005-2012. Drivers using unstudded tires were more experienced and their profession was more frequently related to driving. In addition, the vehicle age was lower for vehicles with unstudded tires. On the other hand, the state of repair was less pertinent for unstudded than for studded tires. These confounding factors offset their effects to some degree. The risk of fatal road accidents in winter between studded and unstudded tires does not differ significantly. However, the accident risk has recently been substantially higher on bald ice for unstudded than for studded tires. The magnitude of this risk difference is difficult to determine without specific information on exposure by road surface.

Rubber friction and tire dynamics

International Nuclear Information System (INIS)

Persson, B N J

2011-01-01

We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

Rubber friction and tire dynamics.

Science.gov (United States)

Persson, B N J

2011-01-12

We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

A low-cost hybrid drivetrain concept based on compressed air energy storage

International Nuclear Information System (INIS)

Brown, T.L.; Atluri, V.P.; Schmiedeler, J.P.

2014-01-01

Highlights: • A new pneumatic hybrid concept is introduced. • A proof-of-concept prototype system is built and tested. • The experimental system has a round-trip efficiency of just under 10%. • A thermodynamics model is used to predict the performance of modified designs. • An efficiency of nearly 50% is possible with reasonable design changes. - Abstract: This paper introduces a new low-cost hybrid drivetrain concept based on compressed air energy storage. In contrast to most contemporary approaches to pneumatic hybridization, which require modification to the primary power plant, this concept is based on a stand-alone pneumatic system that could be readily integrated with existing vehicles. The pneumatic system consists of an air tank and a compressor–expander that is coupled to the rest of the drivetrain via an infinitely variable transmission. Rather than incorporating more expensive technologies such as variable valve timing or a variable compression ratio compressor, a fixed valve system consisting of a rotary valve and passive check valves is optimized to operate efficiently over a range of tank pressures. The feasibility of this approach is established by thermodynamic modeling and the construction of a proof-of-concept prototype, which is also used to fine tune model parameters. While the proof-of-concept system shows a round trip efficiency of just under 10%, modeling shows that a round trip efficiency of 26% is possible with a revised design. If waste heat from the engine is used to maintain an elevated tank temperature, efficiencies of nearly 50% may be possible, indicating that the concept could be effective for practical hybridization of passenger vehicles

Silica-filled tire tread compounds: an investigation into the viscoelastic properties of the rubber compounds and their relation to tire performance

NARCIS (Netherlands)

Maghami, S.

2016-01-01

With increasing the global concern for fossil fuel consumption, automotive industry moves toward more efficient vehicles. Tires are of great importance in this respect, as the tire compound material in contact with the road surface and under the cyclic deformation dissipates energy due to its

A Multisensing Setup for the Intelligent Tire Monitoring.

Science.gov (United States)

Coppo, Francesco; Pepe, Gianluca; Roveri, Nicola; Carcaterra, Antonio

2017-03-12

The present paper offers the chance to experimentally measure, for the first time, the internal tire strain by optical fiber sensors during the tire rolling in real operating conditions. The phenomena that take place during the tire rolling are in fact far from being completely understood. Despite several models available in the technical literature, there is not a correspondently large set of experimental observations. The paper includes the detailed description of the new multi-sensing technology for an ongoing vehicle measurement, which the research group has developed in the context of the project OPTYRE. The experimental apparatus is mainly based on the use of optical fibers with embedded Fiber Bragg Gratings sensors for the acquisition of the circumferential tire strain. Other sensors are also installed on the tire, such as a phonic wheel, a uniaxial accelerometer, and a dynamic temperature sensor. The acquired information is used as input variables in dedicated algorithms that allow the identification of key parameters, such as the dynamic contact patch, instantaneous dissipation and instantaneous grip. The OPTYRE project brings a contribution into the field of experimental grip monitoring of wheeled vehicles, with implications both on passive and active safety characteristics of cars and motorbikes.

Electric energy storage systems for future hybrid vehicles

Energy Technology Data Exchange (ETDEWEB)

Kemper, Hans; Huelshorst, Thomas [FEV Motorentechnik GmbH, Aachen (Germany); Sauer, Dirk Uwe [Elektrochemische Energiewandlung und Speichersystemtechnik, ISEA, RWTH Aachen Univ. (Germany)

2008-07-01

Electric energy storage systems play a key role in today's and even more in future hybrid and electric vehicles. They enable new additional functionalities like Start/Stop, regenerative braking or electric boost and pure electric drive. This article discusses properties and requirements of battery systems like power provision, energy capacity, life time as a function of the hybrid concepts and the real operating conditions of the today's and future hybrid drivetrains. Battery cell technology, component sizing, system design, operating strategy safety measures and diagnosis, modularity and vehicle integration are important battery development topics. A final assessment will draw the conclusion that future drivetrain concepts with higher degree of electrician will be significantly dependent on the progress of battery technology. (orig.)

SIMULATION AND INVESTIGATION OF TIRE TREAD BLOCKS INTERACTION WITH ICE

Directory of Open Access Journals (Sweden)

Andrius Ružinskas

2017-12-01

Full Text Available The car tire is an essential subject analysing its interaction with the road. From tire’s tread condition, geometry and rubber compound depends grip and vehicle stability. This is especially relevant in winter time, when roads are covered with the layer of snow or ice. Generally, new tires are tested in real traffic conditions using vehicles. However, ensuring these conditions requires many resources and sometimes it could be a big challenge. For this reason, simulation of the tire interaction with the road becomes more important in nowadays tire researches. Since the tire is a complex engineering subject, the tire tread blocks could be separated for individual analysis. The interaction between the dry ice and the tread block with sipes was analysed using finite element analysis. The tread block was described using hyperelastic Mooney­Rivlin material model. The deformations, distribution of the contact pressure and shear stresses were obtained for the soft and hard rubber compounds with different vertical load conditions. Also a solid tread block interaction was analysed and it was found that values of contact pressure and shear stresses are much lower comparing to siped tread block.

A Multisensing Setup for the Intelligent Tire Monitoring

Directory of Open Access Journals (Sweden)

Francesco Coppo

2017-03-01

Full Text Available The present paper offers the chance to experimentally measure, for the first time, the internal tire strain by optical fiber sensors during the tire rolling in real operating conditions. The phenomena that take place during the tire rolling are in fact far from being completely understood. Despite several models available in the technical literature, there is not a correspondently large set of experimental observations. The paper includes the detailed description of the new multi-sensing technology for an ongoing vehicle measurement, which the research group has developed in the context of the project OPTYRE. The experimental apparatus is mainly based on the use of optical fibers with embedded Fiber Bragg Gratings sensors for the acquisition of the circumferential tire strain. Other sensors are also installed on the tire, such as a phonic wheel, a uniaxial accelerometer, and a dynamic temperature sensor. The acquired information is used as input variables in dedicated algorithms that allow the identification of key parameters, such as the dynamic contact patch, instantaneous dissipation and instantaneous grip. The OPTYRE project brings a contribution into the field of experimental grip monitoring of wheeled vehicles, with implications both on passive and active safety characteristics of cars and motorbikes.

Configurations Of Tire Pressure On The Pavement For Commercial Vehicles: Calculation Of The ‘N’ Number And The Consequences On Pavement Performance

Directory of Open Access Journals (Sweden)

Paulo Boulos Filho

2016-07-01

Full Text Available Road traffic has a high variety of types of vehicles and cargo transported. One of the main difficulties in pavement design is forecasting the changes in traffic over time and evaluating the comparative deterioration power of the various loads with axle and tire settings and different levels of repetition. The road environment in Brazil, as we know, is the main means of the country's cargo transportation. Throughout the 1990s and 2000s the road modal accounted for over 60% of the total cargo transported in the country leaving the unbalanced Brazilian transport matrix with almost exclusive investments in such means of transportation. According to CNT 2012, which conducted a survey in approximately 45% of the paved network, evaluating the pavement functional conditions, traffic signs and geometry, 46% of the country’s road network has some type of deficiency in the pavement. The goal of this work is to contribute to a better understanding of the complex influence of traffic in the design and service life of the pavement. The load pressure of commercial vehicle tires over the pavement has increased in recent decades. A more apparent effect of this increase in tire pressure would be the change in the pavement- tire contact area which in turn may result in an increase in the contact load between tire and pavement and other harmful effects on the structure. This study aims to determine the effect on the calculation of the N number, or the number of solicitations of the standard axle on the road pavement, measuring the overload as a percentage of the legal load indicated by a scale. In short, we calculate how an increase in the overload percentage in comparison with the allowable load will influence the decrease of the calculated durability of the pavement designed for the highway.

Hybrid Soft Soil Tire Model (HSSTM). Part 1: Tire Material and Structure Modeling

Science.gov (United States)

2015-04-28

Germany. p. 18. 2. Oertel, C., On Modeling Contact and Friction Calculation of Tyre Response on Uneven Roads . Vehicle System Dynamics, 1997. 27(S1): p...touching the ground. This massless tip acts as a sensor point and can be used to detect the tire- road contact . Also, using the direction and value of the...superiority of this model as compared to other lumped parameter models currently available. Keywords: Wheeled Vehicle, Terramechanics, Off- Road

Numerical Simulation of the Ground Response to the Tire Load Using Finite Element Method

Science.gov (United States)

Valaskova, Veronika; Vlcek, Jozef

2017-10-01

Response of the pavement to the excitation caused by the moving vehicle is one of the actual problems of the civil engineering practice. The load from the vehicle is transferred to the pavement structure through contact area of the tires. Experimental studies show nonuniform distribution of the pressure in the area. This non-uniformity is caused by the flexible nature and the shape of the tire and is influenced by the tire inflation. Several tire load patterns, including uniform distribution and point load, were involved in the numerical modelling using finite element method. Applied tire loads were based on the tire contact forces of the lorry Tatra 815. There were selected two procedures for the calculations. The first one was based on the simplification of the vehicle to the half-part model. The characteristics of the vehicle model were verified by the experiment and by the numerical model in the software ADINA, when vehicle behaviour during the ride was investigated. Second step involved application of the calculated contact forces for the front axle as the load on the multi-layered half space representing the pavement structure. This procedure was realized in the software Plaxis and considered various stress patterns for the load. The response of the ground to the vehicle load was then analyzed. Axisymmetric model was established for this procedure. The paper presents the results of the investigation of the contact pressure distribution and corresponding reaction of the pavement to various load distribution patterns. The results show differences in some calculated quantities for different load patterns, which need to be verified by the experimental way when also ground response should be observed.

Novel Low Cost, High Reliability Wind Turbine Drivetrain

Energy Technology Data Exchange (ETDEWEB)

Chobot, Anthony; Das, Debarshi; Mayer, Tyler; Markey, Zach; Martinson, Tim; Reeve, Hayden; Attridge, Paul; El-Wardany, Tahany

2012-09-13

Clipper Windpower, in collaboration with United Technologies Research Center, the National Renewable Energy Laboratory, and Hamilton Sundstrand Corporation, developed a low-cost, deflection-compliant, reliable, and serviceable chain drive speed increaser. This chain and sprocket drivetrain design offers significant breakthroughs in the areas of cost and serviceability and addresses the key challenges of current geared and direct-drive systems. The use of gearboxes has proven to be challenging; the large torques and bending loads associated with use in large multi-MW wind applications have generally limited demonstrated lifetime to 8-10 years [1]. The large cost of gearbox replacement and the required use of large, expensive cranes can result in gearbox replacement costs on the order of $1M, representing a significant impact to overall cost of energy (COE). Direct-drive machines eliminate the gearbox, thereby targeting increased reliability and reduced life-cycle cost. However, the slow rotational speeds require very large and costly generators, which also typically have an undesirable dependence on expensive rare-earth magnet materials and large structural penalties for precise air gap control. The cost of rare-earth materials has increased 20X in the last 8 years representing a key risk to ever realizing the promised cost of energy reductions from direct-drive generators. A common challenge to both geared and direct drive architectures is a limited ability to manage input shaft deflections. The proposed Clipper drivetrain is deflection-compliant, insulating later drivetrain stages and generators from off-axis loads. The system is modular, allowing for all key parts to be removed and replaced without the use of a high capacity crane. Finally, the technology modularity allows for scalability and many possible drivetrain topologies. These benefits enable reductions in drivetrain capital cost by 10.0%, levelized replacement and O&M costs by 26.7%, and overall cost of

Detection of Naturally Occurring Gear and Bearing Faults in a Helicopter Drivetrain

Science.gov (United States)

2014-01-01

Detection of Naturally Occurring Gear and Bearing Faults in a Helicopter Drivetrain by Kelsen E. LaBerge, Eric C. Ames, and Brian D. Dykas...5066 ARL-TR-6795 January 2014 Detection of Naturally Occurring Gear and Bearing Faults in a Helicopter Drivetrain Kelsen E. LaBerge...ELEMENT NUMBER 6. AUTHOR(S) Kelsen E. LaBerge, Eric C. Ames, and Brian D. Dykas 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER

Exploring Optimization Opportunities in Four-Point Suspension Wind Turbine Drivetrains through Integrated Design Approaches

Energy Technology Data Exchange (ETDEWEB)

Sethuraman, Latha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Quick, Julian [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Guo, Yi [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dykes, Katherine L [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-12

Drivetrain design has significant influence on the costs of wind power generation. Current industry practices usually approach the drivetrain design with loads and system requirements defined by the turbine manufacturer. Several different manufacturers are contracted to supply individual components from the low-speed shaft to the generator - each receiving separate design specifications from the turbine manufacturer. Increasingly, more integrated approaches to turbine design have shown promise for blades and towers. Yet, integrated drivetrain design is a challenging task owing to the complex physical behavior of the important load-bearing components, namely the main bearings, gearbox, and the generator. In this paper we combine two of NREL's systems engineering design tools, DriveSE and GeneratorSE, to enable a comprehensive system-level drivetrain optimization for the IEAWind reference turbine for land-based applications. We compare a more traditional design with integrated approaches employing decoupled and coupled design optimization. It is demonstrated that both approaches have the potential to realize notable mass savings with opportunities to lower the costs of energy.

Variable Parameter Nonlinear Control for Maximum Power Point Tracking Considering Mitigation of Drive-train Load

Institute of Scientific and Technical Information of China (English)

Zaiyu; Chen; Minghui; Yin; Lianjun; Zhou; Yaping; Xia; Jiankun; Liu; Yun; Zou

2017-01-01

Since mechanical loads exert a significant influence on the life span of wind turbines, the reduction of transient load on drive-train shaft has received more attention when implementing a maximum power point tracking(MPPT) controller.Moreover, a trade-off between the efficiency of wind energy extraction and the load level of drive-train shaft becomes a key issue. However, for the existing control strategies based on nonlinear model of wind turbines, the MPPT efficiencies are improved at the cost of the intensive fluctuation of generator torque and significant increase of transient load on drive train shaft. Hence, in this paper, a nonlinear controller with variable parameter is proposed for improving MPPT efficiency and mitigating transient load on drive-train simultaneously. Then,simulations on FAST(Fatigue, Aerodynamics, Structures, and Turbulence) code and experiments on the wind turbine simulator(WTS) based test bench are presented to verify the efficiency improvement of the proposed control strategy with less cost of drive-train load.

Variable Parameter Nonlinear Control for Maximum Power Point Tracking Considering Mitigation of Drive-train Load

Institute of Scientific and Technical Information of China (English)

Zaiyu Chen; Minghui Yin; Lianjun Zhou; Yaping Xia; Jiankun Liu; Yun Zou

2017-01-01

Since mechanical loads exert a significant influence on the life span of wind turbines,the reduction of transient load on drive-train shaft has received more attention when implementing a maximum power point tracking (MPPT) controller.Moreover,a trade-off between the efficiency of wind energy extraction and the load level of drive-train shaft becomes a key issue.However,for the existing control strategies based on nonlinear model of wind turbines,the MPPT efficiencies are improved at the cost of the intensive fluctuation of generator torque and significant increase of transient load on drive train shaft.Hence,in this paper,a nonlinear controller with variable parameter is proposed for improving MPPT efficiency and mitigating transient load on drive-train simultaneously.Then,simulations on FAST (Fatigue,Aerodynamics,Structures,and Turbulence) code and experiments on the wind turbine simulator (WTS) based test bench are presented to verify the efficiency improvement of the proposed control strategy with less cost of drive-train load.

Development of a piezoelectric energy harvesting system for implementing wireless sensors on the tires

International Nuclear Information System (INIS)

Lee, Jaeyun; Choi, Bumkyoo

2014-01-01

Highlights: • This study is focused on a stable energy source independent of vehicle speed. • It is ascertained that the use of a strain field is suitable for this purpose. • A piezo patch generates 380.2 μJ per revolution under 500 kgf load and 60 km/h. • A self-powered wireless sensor system is manufactured for application and tested during vehicle driving. • The system is applicable to intelligent tire sensor systems. - Abstract: The need for energy harvesting technology is steadily growing in the field of self-powered wireless sensor systems for intelligent tires. The purpose of this study is to mount an energy harvester inside the tire. In order to achieve this, we focus on a stable energy source almost independent of vehicle speed. It is ascertained that the use of a strain field is suitable for this purpose. In order to develop the energy harvester for the tire, modeling of tire behavior has been performed and verified through comparing with experimental results. From the results, a piezoelectric energy harvester generates 380.2 μJ per revolution under 500 kgf load and 60 km/h. A self-powered wireless sensor system is manufactured for application and tested during vehicle driving. The result of this study presents 1.37 μW/mm 3 of power generation from the performance of the energy harvester. This study concludes that the system is applicable to wireless tire sensor systems after making minor improvements

75 FR 28319 - Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-05-20

... concludes in part that ``the actual tire performance is not inconsequential as it relates to motor vehicle safety because the actual tire performance is not affected by this noncompliance, and in the unlikely...-0056; Notice 1] Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential...

75 FR 17827 - Goodyear Tire & Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-04-07

... Motor Vehicle Safety performance standards. All of the markings related to tire service (load capacity..., and tread wear, temperature, and traction ratings, to assess performance capabilities of various tires...-0213; Notice 2] Goodyear Tire & Rubber Company, Grant of Petition for Decision of Inconsequential...

78 FR 47049 - Bridgestone Americas Tire Operations, LLC, Grant of Petition for Decision of Inconsequential...

Science.gov (United States)

2013-08-02

... on the operational performance or safety of vehicles on which these tires are mounted. Bridgestone..., and tread wear, temperature, and traction ratings to assess performance capabilities of various tires...-0108; Notice 2] Bridgestone Americas Tire Operations, LLC, Grant of Petition for Decision of...

Optimal tread design for agricultural lug tires determined through failure analysis

Directory of Open Access Journals (Sweden)

Hyun Seok Song

2018-04-01

Full Text Available Agricultural lug tires, commonly used in tractors, must provide safe and stable support for the body of the vehicle and bear any additional load while effectively traversing rough, poor-quality ground surfaces. Many agricultural lug tires fail unexpectedly. In this study, we optimised and validated a tread design for agricultural lug tires intended to increase their durability using failure analysis. Specifically, we identified tire failure modes using indoor driving tests and failure mode effects analysis. Next, we developed a threedimensional tire model using the Ogden material model and finite element method. Using sensitivity analysis and response surface methodology, we optimised the tread design. Finally, we evaluated the durability of the new design using a tire prototype and drum test equipment. Results indicated that the optimised tread design decreased the tire tread stress by 16% and increased its time until cracking by 38% compared to conventional agricultural lug tires.

49 CFR 571.138 - Standard No. 138; Tire pressure monitoring systems.

Science.gov (United States)

2010-10-01

... following statement in English: Each tire, including the spare (if provided), should be checked monthly when... level to trigger illumination of the TPMS low tire pressure telltale. [The following paragraph is.... If necessary, drive the vehicle until the telltale has extinguished. (o) The test may be repeated...

75 FR 68855 - Pirelli Tire LLC, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-11-09

... noncompliance has an inconsequential effect on tire performance and motor vehicle safety because all of the affected tires meet or exceed all of the minimum performance requirements of FMVSS No. 139. In addition... performance tires; their asymmetric tread design is one of the main features sought by consumers for the...

78 FR 27476 - Pirelli Tire LLC, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-05-10

... performance and motor vehicle safety because all of the affected tires meet or exceed all of the [[Page 27477... are ultra high performance tires; their asymmetric tread design is one of the main features sought by... these performance characteristics, the customers seek to ensure that their tires are installed correctly...

Tire traces - discrimination and classification of pyrolysis-GC/MS profiles.

Science.gov (United States)

Gueissaz, Line; Massonnet, Geneviève

2013-07-10

Tire traces can be observed on several crime scenes as vehicles are often used by criminals. The tread abrasion on the road, while braking or skidding, leads to the production of small rubber particles which can be collected for comparison purposes. This research focused on the statistical comparison of Py-GC/MS profiles of tire traces and tire treads. The optimisation of the analytical method was carried out using experimental designs. The aim was to determine the best pyrolysis parameters regarding the repeatability of the results. Thus, the pyrolysis factor effect could also be calculated. The pyrolysis temperature was found to be five time more important than time. Finally, a pyrolysis at 650°C during 15s was selected. Ten tires of different manufacturers and models were used for this study. Several samples were collected on each tire, and several replicates were carried out to study the variability within each tire (intravariability). More than eighty compounds were integrated for each analysis and the variability study showed that more than 75% presented a relative standard deviation (RSD) below 5% for the ten tires, thus supporting a low intravariability. The variability between the ten tires (intervariability) presented higher values and the ten most variant compounds had a RSD value above 13%, supporting their high potential of discrimination between the tires tested. Principal Component Analysis (PCA) was able to fully discriminate the ten tires with the help of the first three principal components. The ten tires were finally used to perform braking tests on a racetrack with a vehicle equipped with an anti-lock braking system. The resulting tire traces were adequately collected using sheets of white gelatine. As for tires, the intravariability for the traces was found to be lower than the intervariability. Clustering methods were carried out and the Ward's method based on the squared Euclidean distance was able to correctly group all of the tire traces

Dynamic tire pressure sensor for measuring ground vibration.

Science.gov (United States)

Wang, Qi; McDaniel, James Gregory; Wang, Ming L

2012-11-07

This work presents a convenient and non-contact acoustic sensing approach for measuring ground vibration. This approach, which uses an instantaneous dynamic tire pressure sensor (DTPS), possesses the capability to replace the accelerometer or directional microphone currently being used for inspecting pavement conditions. By measuring dynamic pressure changes inside the tire, ground vibration can be amplified and isolated from environmental noise. In this work, verifications of the DTPS concept of sensing inside the tire have been carried out. In addition, comparisons between a DTPS, ground-mounted accelerometer, and directional microphone are made. A data analysis algorithm has been developed and optimized to reconstruct ground acceleration from DTPS data. Numerical and experimental studies of this DTPS reveal a strong potential for measuring ground vibration caused by a moving vehicle. A calibration of transfer function between dynamic tire pressure change and ground acceleration may be needed for different tire system or for more accurate application.

40 CFR 86.1830-01 - Acceptance of vehicles for emission testing.

Science.gov (United States)

2010-07-01

... shall have tires with appropriate tire wear. (b) Special provisions for durability data vehicles. (1... previous model year emission data vehicles, running change vehicles, fuel economy data vehicles, and...

Exploring Optimization Opportunities in Four-Point Suspension Wind Turbine Drivetrains Through Integrated Design Approaches: Preprint

Energy Technology Data Exchange (ETDEWEB)

Sethuraman, Latha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Quick, Julian [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Guo, Yi [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dykes, Katherine L [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-02-13

Drivetrain design has significant influence on the costs of wind power generation. Current industry practices usually approach the drivetrain design with loads and system requirements defined by the turbine manufacturer. Several different manufacturers are contracted to supply individual components from the low-speed shaft to the generator - each receiving separate design specifications from the turbine manufacturer. Increasingly, more integrated approaches to turbine design have shown promise for blades and towers. Yet, integrated drivetrain design is a challenging task owing to the complex physical behavior of the important load-bearing components, namely the main bearings, gearbox, and the generator. In this paper we combine two of NREL's systems engineering design tools, DriveSE and GeneratorSE, to enable a comprehensive system-level drivetrain optimization for the IEAWind reference turbine for land-based applications. We compare a more traditional design with integrated approaches employing decoupled and coupled design optimization. It is demonstrated that both approaches have the potential to realize notable mass savings with opportunities to lower the costs of energy.

Hydraulic Hybrid and Conventional Parcel Delivery Vehicles' Measured Laboratory Fuel Economy on Targeted Drive Cycles

Energy Technology Data Exchange (ETDEWEB)

Lammert, M. P.; Burton, J.; Sindler, P.; Duran, A.

2014-10-01

This research project compares laboratory-measured fuel economy of a medium-duty diesel powered hydraulic hybrid vehicle drivetrain to both a conventional diesel drivetrain and a conventional gasoline drivetrain in a typical commercial parcel delivery application. Vehicles in this study included a model year 2012 Freightliner P100H hybrid compared to a 2012 conventional gasoline P100 and a 2012 conventional diesel parcel delivery van of similar specifications. Drive cycle analysis of 484 days of hybrid parcel delivery van commercial operation from multiple vehicles was used to select three standard laboratory drive cycles as well as to create a custom representative cycle. These four cycles encompass and bracket the range of real world in-use data observed in Baltimore United Parcel Service operations. The NY Composite cycle, the City Suburban Heavy Vehicle Cycle cycle, and the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) cycle as well as a custom Baltimore parcel delivery cycle were tested at the National Renewable Energy Laboratory's Renewable Fuels and Lubricants Laboratory. Fuel consumption was measured and analyzed for all three vehicles. Vehicle laboratory results are compared on the basis of fuel economy. The hydraulic hybrid parcel delivery van demonstrated 19%-52% better fuel economy than the conventional diesel parcel delivery van and 30%-56% better fuel economy than the conventional gasoline parcel delivery van on cycles other than the highway-oriented HHDDT cycle.

Truck Rollover Characterization for Class-8 Tractor-Trailers Utilizing Standard Dual Tires and New-Generation Single Tires

Energy Technology Data Exchange (ETDEWEB)

Capps, Gary [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). National Transportation Research Center; Knee, Bill [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). National Transportation Research Center; Franzese, Oscar [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). National Transportation Research Center; Pollock, Paul [Dana Corporation, Kalamazoo, MI (United States). Commercial Vehicle Systems Division; Coleman, Daniel [Dana Corporation, Kalamazoo, MI (United States). Commercial Vehicle Systems Division; Janajreh, Ibrahim [Michelin Americas Research and Development Corporation, Greenville, SC (United States); Haas, Steven [Michelin Americas Research and Development Corporation, Greenville, SC (United States); Frey, Norm [Michelin Americas Research and Development Corporation, Greenville, SC (United States); Law, Harry [Clemson Univ., SC (United States). Fluor Daniel Engineering Innovation Building; Johnson, Eric [Clemson Univ., SC (United States). Fluor Daniel Engineering Innovation Building; Lawson, Robert [Clemson Univ., SC (United States). Fluor Daniel Engineering Innovation Building; Petrolino, Joe [National Transportation Research Center, Inc., Knoxville, TN (United States); Rice, Dave [National Transportation Research Center, Inc., Knoxville, TN (United States)

2005-07-30

The Heavy Truck Rollover Characterization Project is a major research effort conducted by the National Transportation Research Center, Inc. (NTRCI) in partnership with Oak Ridge National Laboratory (ORNL), Dana Corporation (Dana), Michelin Americas Research and Development Corporation (Michelin) and Clemson University (Clemson), under the NTRCIs Heavy Vehicle Safety Research Center (HVSRC) for the Federal Highway Administration (FHWA). ORNL provided the day-to-day management of the project. The expertise mix of this team coupled with complementary research needs and interests, and a positive can-do attitude provided an extremely positive experimental research opportunity for all involved. Furthermore, this team supplied significant and valuable resources that provided a strong positive benchmark regarding the ability to conduct research within a public-private partnership. The work conducted by this team focused on initial efforts to generate data and information on heavy truck rollover not currently available in the industry. It reflects efforts within Phases 1 and 2 of a longer-term four-phase research program. A 1999 Peterbilt 379 class-8 tractor and 2004 Wabash dry freight van trailer were the test vehicles utilized in this effort. Both were instrumented with a number of sensors to capture the dynamics of the tractor and trailer as it engaged in various testing maneuvers that included: an evasive maneuver, swept sine, constant radius, and a run-off-the-road maneuver. The run-off-the-road maneuver was discontinued because the test track could not safety accommodate such a maneuver. These maneuvers were carried out utilizing both standard dual tires and new-generation dual tires in six test series. Two test series also included the use of a wider-slider suspension. Outriggers were placed on the test vehicle to assure that an actual rollover would not occur, however, the tests were designed to generate lift-off of tires during the tests. One of the main objectives

Three Three-Axis IEPE Accelerometers on the Inner Liner of a Tire for Finding the Tire-Road Friction Potential Indicators.

Science.gov (United States)

Niskanen, Arto; Tuononen, Ari J

2015-08-05

Direct tire-road contact friction estimation is essential for future autonomous cars and active safety systems. Friction estimation methods have been proposed earlier for driving conditions in the presence of a slip angle or slip ratio. However, the estimation of the friction from a freely-rolling tire is still an unsolved topic. Knowing the existing friction potential would be beneficial since vehicle control systems could be adjusted before any remarkable tire force has been produced. Since accelerometers are well-known and robust, and thus a promising sensor type for intelligent tires, this study uses three three-axis IEPE accelerometers on the inner liner of a tire to detect friction potential indicators on two equally smooth surfaces with different friction levels. The equal roughness was chosen for both surfaces in order to study the friction phenomena by neglecting the effect of surface texture on vibrations. The acceleration data before the contact is used to differentiate the two friction levels between the tire and the road. In addition, the contact lengths from the three accelerometers are used to validate the acceleration data. A method to differentiate the friction levels on the basis of the acceleration signal is also introduced.

CVT control and vehicle acceleration; CVT hensoku ni yoru shasoku otosei

Energy Technology Data Exchange (ETDEWEB)

Takiyama, T; Morita, S [Osaka City University, Osaka (Japan)

1997-10-01

For the drivetrain control, it becomes important for fuel economy or AHS to control the throttle valve of the engine and the gear ratio of CVT simultaneously by DBW when CVT is equipped with the automobile. In this paper, LQI control theory was applied to control the drivetrain as 2-I/O system to satisfy the commanded speed and better fuel economy. And modification of the weight parameter of LQI was investigated to obtain the desired performance for fuel economy or vehicle acceleration. Relatively good expected results were obtained. 5 refs., 7 figs., 1 tab.

Materials Approach to Fuel Efficient Tires

Energy Technology Data Exchange (ETDEWEB)

Votruba-Drzal, Peter [PPG Industries, Monroeville, PA (United States); Kornish, Brian [PPG Industries, Monroeville, PA (United States)

2015-06-30

The objective of this project was to design, develop, and demonstrate fuel efficient and safety regulation compliant tire filler and barrier coating technologies that will improve overall fuel efficiency by at least 2%. The program developed and validated two complementary approaches to improving fuel efficiency through tire improvements. The first technology was a modified silica-based product that is 15% lower in cost and/or enables a 10% improvement in tread wear while maintaining the already demonstrated minimum of 2% improvement in average fuel efficiency. The second technology was a barrier coating with reduced oxygen transmission rate compared to the state-of-the-art halobutyl rubber inner liners that will provide extended placarded tire pressure retention at significantly reduced material usage. A lower-permeance, thinner inner liner coating which retains tire pressure was expected to deliver the additional 2% reduction in fleet fuel consumption. From the 2006 Transportation Research Board Report1, a 10 percent reduction in rolling resistance can reduce consumer fuel expenditures by 1 to 2 percent for typical vehicles. This savings is equivalent to 6 to 12 gallons per year. A 1 psi drop in inflation pressure increases the tire's rolling resistance by about 1.4 percent.

Power Converter Control Algorithm Design and Simulation for the NREL Next-Generation Drivetrain: July 8, 2013 - January 7, 2016

Energy Technology Data Exchange (ETDEWEB)

Blodgett, Douglas [DNV KEMA Renewables, Inc., San Ramon, CA (United States); Behnke, Michael [DNV KEMA Renewables, Inc., San Ramon, CA (United States); Erdman, William [DNV KEMA Renewables, Inc., San Ramon, CA (United States)

2016-08-01

The National Renewable Energy Laboratory (NREL) and NREL Next-Generation Drivetrain Partners are developing a next-generation drivetrain (NGD) design as part of a Funding Opportunity Announcement award from the U.S. Department of Energy. The proposed NGD includes comprehensive innovations to the gearbox, generator, and power converter that increase the gearbox reliability and drivetrain capacity, while lowering deployment and operation and maintenance costs. A key task within this development effort is the power converter fault control algorithm design and associated computer simulations using an integrated electromechanical model of the drivetrain. The results of this task will be used in generating the embedded control software to be utilized in the power converter during testing of the NGD in the National Wind Technology Center 2.5-MW dynamometer. A list of issues to be addressed with these algorithms was developed by review of the grid interconnection requirements of various North American transmission system operators, and those requirements that presented the greatest impact to the wind turbine drivetrain design were then selected for mitigation via power converter control algorithms.

The DOE Next-Generation Drivetrain for Wind Turbine Applications: Gearbox, Generator, and Advanced Si/SiC Hybrid Inverter System: Preprint

Energy Technology Data Exchange (ETDEWEB)

Erdman, William; Keller, Jonathan

2016-08-01

This paper reports on the design and testing results from the U.S. Department of Energy Next-Generation Wind Turbine Drivetrain Project. The drivetrain design reduces the cost of energy by increasing energy capture through drivetrain efficiency improvements; by reducing operation and maintenance costs through reducing gearbox failures; and by lowering capital costs through weight reduction and a series of mechanical and electronic innovations. The paper provides an overview of the drivetrain gearbox and generator and provides a deeper look into the power converter system. The power converter has a number of innovations including the use of hybrid silicon (Si)/silicon carbide (SiC) isolated baseplate switching modules. Switching energies are compared between SiC and Si PIN diodes. The efficiency improvement by use of the SiC diode in a three-level converter is also described. Finally, a brief discussion covering utility interconnect requirements for turbines is provided with a particular focus on utility events that lead to high transient torque loads on drivetrain mechanical elements.

Optimization of an Optical Test Bench for Tire Properties Measurement and Tread Defects Characterization

Directory of Open Access Journals (Sweden)

Juan Jesús Castillo Aguilar

2017-03-01

Full Text Available Tire characteristics and behavior are of great importance in vehicle dynamics since the forces transmitted in the tire-road contact are the main contributors to global vehicle performance. Several research groups have focused on the study and modeling of tires. Some of the most important factors that need to be known are tread characteristics and pressure distribution in the tire-ground contact patch. In this work, a test bench has been used to adequately determine the aforementioned factors. The measurement principle of the test bench is the frustration of total internal reflection (FTIR of light. It makes use of a laterally illuminated glass on which the tire leans. An interposed plastic interface between them causes the reflection of light. Finally, a video camera captures the bright image formed through the glass. The brightness level in each pixel of the image is related to existing normal pressure. A study of the parameters that affect the test bench calibration such as type of interface material used, diffuse light, hysteresis, creep and transverse light absorption is performed. Experimental tests are conducted to relate tire inflation pressure and camber angle to the pressure distribution. Furthermore, the test bench is used to detect and evaluate the influence of defects in the tire on the contact pressures.

Three Three-Axis IEPE Accelerometers on the Inner Liner of a Tire for Finding the Tire-Road Friction Potential Indicators

Directory of Open Access Journals (Sweden)

Arto Niskanen

2015-08-01

Full Text Available Direct tire-road contact friction estimation is essential for future autonomous cars and active safety systems. Friction estimation methods have been proposed earlier for driving conditions in the presence of a slip angle or slip ratio. However, the estimation of the friction from a freely-rolling tire is still an unsolved topic. Knowing the existing friction potential would be beneficial since vehicle control systems could be adjusted before any remarkable tire force has been produced. Since accelerometers are well-known and robust, and thus a promising sensor type for intelligent tires, this study uses three three-axis IEPE accelerometers on the inner liner of a tire to detect friction potential indicators on two equally smooth surfaces with different friction levels. The equal roughness was chosen for both surfaces in order to study the friction phenomena by neglecting the effect of surface texture on vibrations. The acceleration data before the contact is used to differentiate the two friction levels between the tire and the road. In addition, the contact lengths from the three accelerometers are used to validate the acceleration data. A method to differentiate the friction levels on the basis of the acceleration signal is also introduced.

Vehicle Velocity and Roll Angle Estimation with Road and Friction Adaptation for Four-Wheel Independent Drive Electric Vehicle

Directory of Open Access Journals (Sweden)

Linhui Zhao

2014-01-01

Full Text Available Vehicle velocity and roll angle are important information for active safety control systems of four-wheel independent drive electric vehicle. In order to obtain robustness estimation of vehicle velocity and roll angle, a novel method is proposed based on vehicle dynamics and the measurement information provided by the sensors equipped in modern cars. The method is robust with respect to different road and friction conditions. Firstly, the dynamic characteristics of four-wheel independent drive electric vehicle are analyzed, and a four-degree-of-freedom nonlinear dynamic model of vehicle and a tire longitudinal dynamic equation are established. The relationship between the longitudinal and lateral friction forces is derived based on Dugoff tire model. The unknown input reconstruction technique of sliding mode observer is used to achieve longitudinal tire friction force estimation. A simple observer is designed for the estimation of the roll angle of the vehicle. And then using the relationship, the estimated longitudinal friction forces and roll angle, a sliding mode observer for vehicle velocity estimation is provided, which does not need to know the tire-road friction coefficient and road angles. Finally, the proposed method is evaluated experimentally under a variety of maneuvers and road conditions.

Tire Log™

OpenAIRE

ECT Team, Purdue

2013-01-01

The Tire Log™ is a patented innovation made from waste tires with a unique and energy efficient approach to recycling tires. Re-Tread Products (RTP) process takes full advantage of the embedded energy in tires that is wasted in conventional tire recycling that primarily involves the grinding, burying or burning of waste tires.

Dynamic responses of a wind turbine drivetrain under turbulent wind and voltage disturbance conditions

Directory of Open Access Journals (Sweden)

Chengwu Li

2016-05-01

Full Text Available Wind energy is known as one of the most efficient clean renewable energy sources and has attracted extensive research interests in both academic and industry fields. In this study, the effects of turbulent wind and voltage disturbance on a wind turbine drivetrain are analyzed, and a wind turbine drivetrain dynamic model combined with the electric model of a doubly fed induction generator is established. The proposed model is able to account for the dynamic interaction between turbulent wind, voltage disturbance, and mechanical system. Also, the effects of time-varying meshing stiffness, transmission error, and bearing stiffness are included in the mechanical part of the coupled dynamic model. From the resultant model, system modes are computed. In addition, by considering the actual control strategies in the simulation process, the effects of turbulent wind and voltage disturbance on the geared rotor system are analyzed. The computational results show that the turbulent wind and voltage disturbance can cause adverse effects on the wind turbine drivetrain, especially the gearbox. A series of parametric studies are also performed to understand the influences of generator and gearbox parameters on the drivetrain system dynamics. Finally, the appropriate generator parameters having a positive effect on the gearbox in alleviating the extreme loads and the modeling approach for investigating the transient performance of generator are discussed.

The drivetrain strategy of a global company facing international competition; Antriebsstrategien eines Weltkonzerns im globalen Wettbewerb

Energy Technology Data Exchange (ETDEWEB)

Winterkorn, M. [Volkswagen AG, Wolfsburg (Germany)

2007-07-01

The Volkswagen Group has long been aware of its responsibility for climate protection, and vigorously pursues technical innovations to further reduce fuel consumption and emissions - across its entire, extremely wide product range. In models from superminis to luxury saloons, Europe's largest carmaker employs a wide range of technological means to meet stringent environmental legislation worldwide. As a major aspect of its drivetrain strategy, the company is continuing its development of highly efficient TDI, TSI and TFSI engines for all vehicle classes. Hybrid models will also feature among the Volkswagen Group's products on the market. Moreover, the company is carrying out intensive research into alternative fuels and drive systems for the future. (orig.)

A Prognostic Method for Fault Detection in Wind Turbine Drivetrains

DEFF Research Database (Denmark)

Nejada, Amir R.; Odgaard, Peter Fogh; Gao, Zhen

2014-01-01

In this paper, a prognostic method is presented for fault detection in gears and bearings in wind turbine drivetrains. This method is based on angular velocity measurements from the gearbox input shaft and the output to the generator, using two additional angular velocity sensors on the intermedi......In this paper, a prognostic method is presented for fault detection in gears and bearings in wind turbine drivetrains. This method is based on angular velocity measurements from the gearbox input shaft and the output to the generator, using two additional angular velocity sensors...... bearing faults in three locations: the high-speed shaft stage, the planetary stage and the intermediate-speed shaft stage. Simulations of the faulty and fault-free cases are performed on a gearbox model implemented in multibody dynamic simulation software. The global loads on the gearbox are obtained from...

Performance indicators, practices and maintenance costs in tires management of a transport company

Directory of Open Access Journals (Sweden)

Marcos Dario

2014-12-01

Full Text Available There are three operational costs that are more expressive for PSL: vehicle maintenance, tires and fuel. In studies of maintenance has been little researched the concept of tire management, technical maintenance and performance together. In this context, this study aims at identifying the practices and performance indicators in the area of maintenance and tire management also analyze the influence of costs applied to the tires on the total cost of maintenance. We conducted a case study of exploratory and descriptive. The main instruments of data collection were on-site observation, unstructured interviews, document analysis and reports results indicators. Data were analyzed by correlation analysis and multiple regression. It was revealed that among the performance indicators in the management of tire maintenance costs applied to the tires have a higher correlation with the total cost of maintenance. The ANOVA indicated that tire maintenance costs influence in 54% of the variations in the total cost of maintenance. We clarified the concepts of maintenance techniques specific tire management, and identify performance indicators in the area of tire managent.

Tires

Science.gov (United States)

2015-12-15

measure heat from the casing. Tread surface temperature. Tread (surface) infrared temperature can be inconsistent since the measurements are...have any adverse effect on rubber products. b. Avoid areas that are wet, humid, oily, greasy, or in direct sunlight. Do not store tires in the...used, from sticking to the tire. Do not let soapstone accumulate in the tire. Inspect and clean the tire beads to remove corrosion or residual rubber

Intelligent Hybrid Vehicle Power Control - Part 1: Machine Learning of Optimal Vehicle Power

Science.gov (United States)

2012-06-30

the motor or both can provide the traction power to the drivetrain. During vehicle deceleration, the regenerative braking power is captured to charge...and Amax is the maximum acceleration. The 11 drive cycles are divided into four categories of roadway types and traffic congestion levels, freeway...freeway ramp, arterial, and local. Two of the categories , freeway and arterial, are further divided into subcategories based on a qualitative measure

A Procedure for Determining Tire-Road Friction Characteristics Using a Modification of the Magic Formula Based on Experimental Results.

Science.gov (United States)

Cabrera, Juan A; Castillo, Juan J; Pérez, Javier; Velasco, Juan M; Guerra, Antonio J; Hernández, Pedro

2018-03-17

Knowledge of tire-road friction characteristics is essential for the proper performance of most relevant vehicle active safety systems. Therefore, its determination is necessary to improve the effectiveness of these systems and to avoid or reduce the consequences of traffic accidents. For this reason, there is a great deal of literature concerning methods and devices for measuring and modeling tire-road friction. Most of these methods have focused on determining the road friction resistance, taking only road composition and making measurements in wet conditions into account. However, friction forces are also dependent on the tire type, since the contact is established between the tire and the road in real driving conditions. Thus, the type and characteristics of the tire have to be considered in the study of the interaction between the vehicle and the road. The aim of this work is to unify the study of the friction coefficient, taking into consideration the two existing bodies involved in the contact, i.e., the tire and road and the main factors that influence the forces in the contact. To this end, a modification of the Pacejka Magic Formula is proposed to include the effects of the main parameters that influence the contact, such as road composition and its state, tire type, vehicle speed, and slip between the tire and the road. To do so, real tests have been conducted on several roads and with different operating conditions. As a result, a more accurate tire-road friction model has been obtained.

A Procedure for Determining Tire-Road Friction Characteristics Using a Modification of the Magic Formula Based on Experimental Results

Science.gov (United States)

Pérez, Javier; Velasco, Juan M.; Guerra, Antonio J.; Hernández, Pedro

2018-01-01

Knowledge of tire-road friction characteristics is essential for the proper performance of most relevant vehicle active safety systems. Therefore, its determination is necessary to improve the effectiveness of these systems and to avoid or reduce the consequences of traffic accidents. For this reason, there is a great deal of literature concerning methods and devices for measuring and modeling tire-road friction. Most of these methods have focused on determining the road friction resistance, taking only road composition and making measurements in wet conditions into account. However, friction forces are also dependent on the tire type, since the contact is established between the tire and the road in real driving conditions. Thus, the type and characteristics of the tire have to be considered in the study of the interaction between the vehicle and the road. The aim of this work is to unify the study of the friction coefficient, taking into consideration the two existing bodies involved in the contact, i.e., the tire and road and the main factors that influence the forces in the contact. To this end, a modification of the Pacejka Magic Formula is proposed to include the effects of the main parameters that influence the contact, such as road composition and its state, tire type, vehicle speed, and slip between the tire and the road. To do so, real tests have been conducted on several roads and with different operating conditions. As a result, a more accurate tire-road friction model has been obtained. PMID:29562623

A Procedure for Determining Tire-Road Friction Characteristics Using a Modification of the Magic Formula Based on Experimental Results

Directory of Open Access Journals (Sweden)

Juan A. Cabrera

2018-03-01

Full Text Available Knowledge of tire-road friction characteristics is essential for the proper performance of most relevant vehicle active safety systems. Therefore, its determination is necessary to improve the effectiveness of these systems and to avoid or reduce the consequences of traffic accidents. For this reason, there is a great deal of literature concerning methods and devices for measuring and modeling tire-road friction. Most of these methods have focused on determining the road friction resistance, taking only road composition and making measurements in wet conditions into account. However, friction forces are also dependent on the tire type, since the contact is established between the tire and the road in real driving conditions. Thus, the type and characteristics of the tire have to be considered in the study of the interaction between the vehicle and the road. The aim of this work is to unify the study of the friction coefficient, taking into consideration the two existing bodies involved in the contact, i.e., the tire and road and the main factors that influence the forces in the contact. To this end, a modification of the Pacejka Magic Formula is proposed to include the effects of the main parameters that influence the contact, such as road composition and its state, tire type, vehicle speed, and slip between the tire and the road. To do so, real tests have been conducted on several roads and with different operating conditions. As a result, a more accurate tire-road friction model has been obtained.

Upon the reconstruction of accidents triggered by tire explosion. Analytical model and case study

Science.gov (United States)

Gaiginschi, L.; Agape, I.; Talif, S.

2017-10-01

Accident Reconstruction is important in the general context of increasing road traffic safety. In the casuistry of traffic accidents, those caused by tire explosions are critical under the severity of consequences, because they are usually happening at high speeds. Consequently, the knowledge of the running speed of the vehicle involved at the time of the tire explosion is essential to elucidate the circumstances of the accident. The paper presents an analytical model for the kinematics of a vehicle which, after the explosion of one of its tires, begins to skid, overturns and rolls. The model consists of two concurent approaches built as applications of the momentum conservation and energy conservation principles, and allows determination of the initial speed of the vehicle involved, by running backwards the sequences of the road event. The authors also aimed to both validate the two distinct analytical approaches by calibrating the calculation algorithms on a case study

Tire-rim interface pressure of a commercial vehicle wheel under radial loads: theory and experiment

Science.gov (United States)

Wan, Xiaofei; Shan, Yingchun; Liu, Xiandong; He, Tian; Wang, Jiegong

2017-11-01

The simulation of the radial fatigue test of a wheel has been a necessary tool to improve the design of the wheel and calculate its fatigue life. The simulation model, including the strong nonlinearity of the tire structure and material, may produce accurate results, but often leads to a divergence in calculation. Thus, a simplified simulation model in which the complicated tire model is replaced with a tire-wheel contact pressure model is used extensively in the industry. In this paper, a simplified tire-rim interface pressure model of a wheel under a radial load is established, and the pressure of the wheel under different radial loads is tested. The tire-rim contact behavior affected by the radial load is studied and analyzed according to the test result, and the tire-rim interface pressure extracted from the test result is used to evaluate the simplified pressure model and the traditional cosine function model. The results show that the proposed model may provide a more accurate prediction of the wheel radial fatigue life than the traditional cosine function model.

76 FR 4298 - Certain New Pneumatic Off-the-Road Tires From the People's Republic of China: Notice of...

Science.gov (United States)

2011-01-25

... use, including passenger cars, race cars, station wagons, sport utility vehicles, minivans, mobile...--Identifies a tire intended primarily for service on passenger cars; LT--Identifies a tire intended primarily...

75 FR 64259 - Certain New Pneumatic Off-the-Road Tires From the People's Republic of China: Preliminary Results...

Science.gov (United States)

2010-10-19

... use, including passenger cars, race cars, station wagons, sport utility vehicles, minivans, mobile...--Identifies a tire intended primarily for service on passenger cars; LT--Identifies a tire intended primarily...

A Tire Model for Off-Highway Vehicle Simulation and Comfort Evaluation

DEFF Research Database (Denmark)

Langer, Thomas Heegaard; Mouritsen, Ole Ø.; Ebbesen, Morten Kjeld

2009-01-01

Manufacturers of construction machinery are challenged to accommodate legal requirements on the vibration exposure associated with their products. Hence, the ability to evaluate ride comfort by virtual prototyping is needed. One of the derived necessities is a modeling approach that can handle big...... off-road tires on irregular terrain and even the passing of sharp corner obstacles. In this paper a simple tire model combining the well known slip theory and a displaced volume approach is presented. A non-gradient optimization routine is applied for parameter identification by minimizing...

Analytical Formulation for Sizing and Estimating the Dimensions and Weight of Wind Turbine Hub and Drivetrain Components

Energy Technology Data Exchange (ETDEWEB)

Guo, Y. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Parsons, T. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); King, R. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dykes, K. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Veers, P. [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2015-06-09

This report summarizes the theory, verification, and validation of a new sizing tool for wind turbine drivetrain components, the Drivetrain Systems Engineering (DriveSE) tool. DriveSE calculates the dimensions and mass properties of the hub, main shaft, main bearing(s), gearbox, bedplate, transformer if up-tower, and yaw system. The level of fi¬ delity for each component varies depending on whether semiempirical parametric or physics-based models are used. The physics-based models have internal iteration schemes based on system constraints and design criteria. Every model is validated against available industry data or finite-element analysis. The verification and validation results show that the models reasonably capture primary drivers for the sizing and design of major drivetrain components.

Operator interface for vehicles

Science.gov (United States)

Bissontz, Jay E

2015-03-10

A control interface for drivetrain braking provided by a regenerative brake and a non-regenerative brake is implemented using a combination of switches and graphic interface elements. The control interface comprises a control system for allocating drivetrain braking effort between the regenerative brake and the non-regenerative brake, a first operator actuated control for enabling operation of the drivetrain braking, and a second operator actuated control for selecting a target braking effort for drivetrain braking. A graphic display displays to an operator the selected target braking effort and can be used to further display actual braking effort achieved by drivetrain braking.

Automobile tires--a potential source of highly carcinogenic dibenzopyrenes to the environment.

Science.gov (United States)

Sadiktsis, Ioannis; Bergvall, Christoffer; Johansson, Christer; Westerholm, Roger

2012-03-20

Eight tires were analyzed for 15 high molecular weight (HMW) polycyclic aromatic hydrocarbons (PAH), using pressurized fluid extraction. The variability of the PAH concentrations determined between different tires was large; a factor of 22.6 between the lowest and the highest. The relative abundance of the analytes was quite similar regardless of tire. Almost all (92.3%) of the total extractable PAH content was attributed to five PAHs: benzo[ghi]perylene, coronene, indeno[1,2,3-cd]pyrene, benzo[e]pyrene, and benzo[a]pyrene. The difference in the measured PAH content between summer and winter tires varied substantially across manufacturers, making estimates of total vehicle fleet emissions very uncertain. However, when comparing different types of tires from the same manufacturer they had significantly (p = 0.05) different PAH content. Previously, there have been no data available for carcinogenic dibenzopyrene isomers in automobile tires. In this study, the four dibenzopyrene isomers dibenzo[a,l]pyrene, dibenzo[a,e]pyrene, dibenzo[a,i]pyrene, and dibenzo[a,h]pyrene constituted tires may be a potential previously unknown source of carcinogenic dibenzopyrenes to the environment.

Medium-Speed Drivetrain Test Report: September 1, 2002 -- December 30, 2007

Energy Technology Data Exchange (ETDEWEB)

Walford, C.; Lybarger, K.; Lettenmaier, T.; Roberts, D.

2012-09-01

This report describes the tests conducted by researchers at the National Wind Technology Center at NREL on a 1.5-MW integrated drivetrain consisting of a single-stage, epicyclic gearbox and close-coupled medium-speed permanent-magnet generator.

Variable Speed Wind Turbine Based on Multiple Generators Drive-Train Configuration

DEFF Research Database (Denmark)

Deng, Fujin; Chen, Zhe

2010-01-01

A variable speed wind turbine is presented in this paper, where multiple permanent magnet synchronous generators (MPMSGs) drive-train configuration is employed in the wind turbine. A cascaded multilevel converter interface based on the MPMSGs is developed to synthesize a desired high ac sinusoidal...... output voltage, which could be directly connected to the grids. What is more, such arrangement has been made so that the output ac voltage having a selected phase angle difference among the stator windings of multiple generators. A phase angle shift strategy is proposed in this paper, which effectively...... reduce the fluctuation of the electromagnetic torque sum and results in a good performance for the MPMSGs structure. The simulation study is conducted using PSCAD/EMTDC, and the results verify the feasibility of this variable speed wind turbine based on multiple generators drive-train configuration....

Grip Analysis of Road Surface and Tire Footprint Using FEM

Science.gov (United States)

Sabri, M.; Abda, S.

2018-02-01

Road grip involve a touch between road pavement and the tire tread pattern. The load bearing surface, which depends on pavement roughness and local pressures in the contact patch. This research conducted to develop a Finite element model for simulating the experimentally testing of asphalt in Jl. AH Nasution Medan, North Sumatera Indonesia base on the value of grip coefficient from various tire loads and the various speed of the vehicle during contact to the road. A tire model and road pavement are developed for the analyses the geometry of tire footprint. The results showed that the greater the mass of car will increase grip coefficient. The coefficient of grip on the road surface contact trough the tire footprint strongly influence the kinetic coefficient of friction at certain speeds. Experimentally show that Concrete road grip coefficient of more than 34% compared to the asphalt road at the same IRI parameters (6-8). Kinetic friction coefficient more than 0.33 was obtained in a asphalt path at a speed of 30-40 Km/hour.

3 tons pure electric vehicles power system design based on Cruise

Directory of Open Access Journals (Sweden)

Xinyu Liu

2017-01-01

Full Text Available The pure electric minivan is different from electric car. Combined with a given vehicle, vehicle simulation model established in Cruise software, complete simulation by setting tasks for the selected models designed drivetrain. Simulation results show that: The design of the transmission ratio can best meet the performance requirements of the matching target power analysis and simulation of electric minivan provides a new way, with practical guidance.

26 CFR 48.4073-3 - Exemption of tread rubber used for recapping nonhighway tires.

Science.gov (United States)

2010-04-01

... TREASURY (CONTINUED) MISCELLANEOUS EXCISE TAXES MANUFACTURERS AND RETAILERS EXCISE TAXES Motor Vehicles... person otherwise than in the recapping or retreading of tires of the type used on highway vehicles. In determining whether tread rubber is sold for a taxable or nontaxable use, the type of vehicle on which the...

A technical survey on tire-road friction estimation

Institute of Scientific and Technical Information of China (English)

Seyedmeysam KHALEGHIAN; Anahita EMAMI; Saied TAHERI

2017-01-01

Lack of driver's knowledge about the abrupt changes in pavement's friction and poor performance of the vehicle's stability,traction,and ABS controllers on the low friction surfaces are the most important factors affecting car crashes.Due to its direct relation to vehicle stability,accurate estimation of tire-road friction is of interest to all vehicle and tire companies.Many studies have been conducted in this field and researchers have used different tools and have proposed different algorithms.This literature survey introduces different approaches,which have been widely used to estimate the friction or other related parameters,and covers the recent literature that contains these methodologies.The emphasize of this review paper is on the algorithms and studies,which are more popular and have been repeated several times.The focus has been divided into two main groups:experiment-based and model-based approaches.Each of these main groups has several sub-categories,which are explained in the next few sections.Several summary tables are provided in which the overall feature of each approach is reviewed that gives the reader the general picture of different algorithms,which are widely used in friction estimation studies.

ROMO - The Robotic Electric Vehicle

OpenAIRE

Brembeck, Jonathan; Ho, Lok Man; Schaub, Alexander; Satzger, Clemens; Tobolar, Jakub; Bals, Johann; Hirzinger, Gerhard

2011-01-01

This paper outlines the development of the ROboMObil, an innovative electro-mobility concept based on intelligent central control of four Wheel Robots, which integrate the drivetrain, brakes, steering and dampers. The motivation behind the Wheel Robot concept, the implementation details together with the suspension design are described. The electric power system, consisting of a Li-Ion battery cluster to provide high-voltage power for propulsion and a low-voltage supply for vehicle control, i...

Effects of tire leachate on the invasive mosquito Aedes albopictus and the native congener Aedes triseriatus

Directory of Open Access Journals (Sweden)

Oswaldo C. Villena

2017-09-01

Full Text Available Discarded vehicle tire casings are an important artificial habitat for the developmental stages of numerous vector mosquitoes. Discarded vehicle tires degrade under ultraviolet light and leach numerous soluble metals (e.g., barium, cadmium, zinc and organic substances (e.g., benzothiazole and its derivatives [BZTs], polyaromatic hydrocarbons [PAHs] that could affect mosquito larvae that inhabit the tire casing. This study examined the relationship between soluble zinc, a common marker of tire leachate, on mosquito densities in tire habitats in the field, and tested the effects of tire leachate on the survival and development of newly hatched Aedes albopictus and Aedes triseriatus larvae in a controlled laboratory dose-response experiment. In the field, zinc concentrations were as high as 7.26 mg/L in a single tire and averaged as high as 2.39 (SE ± 1.17 mg/L among tires at a single site. Aedes albopictus (37/42 tires, 81.1% and A. triseriatus (23/42, 54.8% were the most widespread mosquito species, co-occurred in over half (22/42, 52.4% of all tires, and A. triseriatus was only collected without A. albopictus in one tire. Aedes triseriatus was more strongly negatively associated with zinc concentration than A. albopictus, and another common mosquito, C. pipiens, which was found in 17 tires. In the laboratory experiment, A. albopictus per capita rate of population change (λ′ was over 1.0, indicating positive population growth, from 0–8.9 mg/L zinc concentration (0–10,000 mg/L tire leachate, but steeply declined to zero from 44.50–89.00 mg/L zinc (50,000–100,000 mg/L tire leachate. In contrast, A. triseriatus λ′ declined at the lower concentration of 0.05 mg/L zinc (100 mg/L tire leachate, and was zero at 0.45, 8.90, 44.50, and 89.00 mg/L zinc (500, 10,000, 50,000 and 100,000 mg/L tire leachate. These results indicate that tire leachate can have severe negative effects on populations of container-utilizing mosquitoes at

Mechanics based model for predicting structure-induced rolling resistance (SRR) of the tire-pavement system

Science.gov (United States)

Shakiba, Maryam; Ozer, Hasan; Ziyadi, Mojtaba; Al-Qadi, Imad L.

2016-11-01

The structure-induced rolling resistance of pavements, and its impact on vehicle fuel consumption, is investigated in this study. The structural response of pavement causes additional rolling resistance and fuel consumption of vehicles through deformation of pavement and various dissipation mechanisms associated with inelastic material properties and damping. Accurate and computationally efficient models are required to capture these mechanisms and obtain realistic estimates of changes in vehicle fuel consumption. Two mechanistic-based approaches are currently used to calculate vehicle fuel consumption as related to structural rolling resistance: dissipation-induced and deflection-induced methods. The deflection-induced approach is adopted in this study, and realistic representation of pavement-vehicle interactions (PVIs) is incorporated. In addition to considering viscoelastic behavior of asphalt concrete layers, the realistic representation of PVIs in this study includes non-uniform three-dimensional tire contact stresses and dynamic analysis in pavement simulations. The effects of analysis type, tire contact stresses, pavement viscoelastic properties, pavement damping coefficients, vehicle speed, and pavement temperature are then investigated.

A fuel cell city bus with three drivetrain configurations

Energy Technology Data Exchange (ETDEWEB)

Wang, Junping [Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi' an Jiaotong University, Xi' an 710049 (China); Chen, Yong [School of Automobile and Transporting Engineering, Liaoning Institute of Technology, Jinzhou, Liaoning 121001 (China); Chen, Quanshi [State Key Laboratory of Automobile Safety and Energy Conservation, Tsinghua University, Beijing 100084 (China)

2006-09-22

Three fuel cell city buses of the energy hybrid- and power hybrid-type were re-engineered with three types of drivetrain configuration to optimize the structure and improve the performance. The energy distribution, hydrogen consumption, state of charge (SOC) and the power variation rate were analyzed when different drivetrain configurations and parameters were used. When powered only by a fuel cell, the bus cannot recover the energy through regenerative braking. The variation of the fuel cell power is large and frequent, which is not good for the fuel cell. When the fuel cell is linked to a battery pack in parallel, the bus can recover the energy through regenerative braking. The energy distribution is determined by the parameters of the fuel cell and the battery pack in the design stage to reduce the power variation rate of the fuel cell. When the fuel cell and DC/DC converter connected in series links the battery pack in parallel, energy can be recovered and the energy distribution can be adjusted online. The power variation rate of both the fuel cell and the battery pack are reduced. (author)

Stability of the Small Electric Vehicle with Two In-Wheel Motors

Directory of Open Access Journals (Sweden)

Heerwan P.M.

2017-01-01

Full Text Available For a small electric vehicle (EV with the rear two in-wheel motors, the hydraulic brake system and the mechanical brake system are installed at the front and rear tire respectively. The mechanical brake system is used at the rear tire because there is no enough space for the hydraulic brake system. In a braking condition, the in-wheel motor at the rear tire will generate the regenerative braking force and it can improve the braking performance of the vehicle. However, during braking on the low adhesion road surface, anti-lock brake system (ABS is very crucial to prevent the tire from lock-up. To improve the safety and stability of the vehicle, the combination of anti-skid control system and direct yaw moment control system is proposed. The anti-skid control system contains a hydraulic unit of ABS at the front tires and regenerative brake timing control at the rear tires. The control method of the regenerative brake timing control is same as ABS and it will turn on and off to prevent the tire from lock-up. On the other hand, the direct yaw moment control system is developed to increase the steer performance of the vehicle. The optimal control is used as the control strategy method to control the yaw moment. The simulation is developed in MATLAB Simulink and the result shows that the proposed model can improve the stopping distance from 9 seconds to 8.2 seconds. In addition, the combination of skid control and yaw moment control also improved the steer performance of the vehicle.

NASA evaluation of Type 2 chemical depositions. [effects of deicer deposition on aircraft tire friction performance

Science.gov (United States)

Yager, Thomas J.; Stubbs, Sandy M.; Howell, W. Edward; Webb, Granville L.

1993-01-01

Recent findings from NASA Langley tests to define effects of aircraft Type 2 chemical deicer depositions on aircraft tire friction performance are summarized. The Aircraft Landing Dynamics Facility (ALDF) is described together with the scope of the tire cornering and braking friction tests conducted up to 160 knots ground speed. Some lower speed 32 - 96 km/hr (20 - 60 mph) test run data obtained using an Instrumented Tire Test Vehicle (ITTV) to determine effects of tire bearing pressure and transverse grooving on cornering friction performance are also discussed. Recommendations are made concerning which parameters should be evaluated in future testing.

Piezoelectric power generation for sensor applications: design of a battery-less wireless tire pressure sensor

Science.gov (United States)

Makki, Noaman; Pop-Iliev, Remon

2011-06-01

An in-wheel wireless and battery-less piezo-powered tire pressure sensor is developed. Where conventional battery powered Tire Pressure Monitoring Systems (TPMS) are marred by the limited battery life, TPMS based on power harvesting modules provide virtually unlimited sensor life. Furthermore, the elimination of a permanent energy reservoir simplifies the overall sensor design through the exclusion of extra circuitry required to sense vehicle motion and conserve precious battery capacity during vehicle idling periods. In this paper, two design solutions are presented, 1) with very low cost highly flexible piezoceramic (PZT) bender elements bonded directly to the tire to generate power required to run the sensor and, 2) a novel rim mounted PZT harvesting unit that can be used to power pressure sensors incorporated into the valve stem requiring minimal change to the presently used sensors. While both the designs eliminate the use of environmentally unfriendly battery from the TPMS design, they offer advantages of being very low cost, service free and easily replaceable during tire repair and replacement.

Vehicle State Information Estimation with the Unscented Kalman Filter

Directory of Open Access Journals (Sweden)

Hongbin Ren

2014-01-01

Full Text Available The vehicle state information plays an important role in the vehicle active safety systems; this paper proposed a new concept to estimate the instantaneous vehicle speed, yaw rate, tire forces, and tire kinemics information in real time. The estimator is based on the 3DoF vehicle model combined with the piecewise linear tire model. The estimator is realized using the unscented Kalman filter (UKF, since it is based on the unscented transfer technique and considers high order terms during the measurement and update stage. The numerical simulations are carried out to further investigate the performance of the estimator under high friction and low friction road conditions in the MATLAB/Simulink combined with the Carsim environment. The simulation results are compared with the numerical results from Carsim software, which indicate that UKF can estimate the vehicle state information accurately and in real time; the proposed estimation will provide the necessary and reliable state information to the vehicle controller in the future.

49 CFR 571.139 - Standard No. 139; New pneumatic radial tires for light vehicles.

Science.gov (United States)

2010-10-01

... breaking away of pieces of the tread or sidewall. Cord means the strands forming the plies in the tire... with a 12-inch or smaller rim diameter, each tire shall have not less than six treadwear indicators... mountain, there must be a six-sided snowflake having a minimum height of one-half the tallest peak...

Stochastic Modeling Of Wind Turbine Drivetrain Components

DEFF Research Database (Denmark)

Rafsanjani, Hesam Mirzaei; Sørensen, John Dalsgaard

2014-01-01

reliable components are needed for wind turbine. In this paper focus is on reliability of critical components in drivetrain such as bearings and shafts. High failure rates of these components imply a need for more reliable components. To estimate the reliability of these components, stochastic models...... are needed for initial defects and damage accumulation. In this paper, stochastic models are formulated considering some of the failure modes observed in these components. The models are based on theoretical considerations, manufacturing uncertainties, size effects of different scales. It is illustrated how...

The new car market for electric vehicles and the potential for fuel substitution

International Nuclear Information System (INIS)

Kihm, Alexander; Trommer, Stefan

2014-01-01

Electric vehicles are expected to significantly reduce road transport emissions, given an increasingly renewable power generation. While technological issues are more and more being overcome, the economic viability and thus possible adoption is still constrained, mainly by higher prices than for conventional vehicles. In our work we analyze possible market developments for electric vehicles with an application to Germany. We develop a drivetrain choice model with economical, technical and social constraints on the current vehicle registrations and inventory. It estimates the demand for electric vehicles until 2030 for private and commercially registered cars as well as light commercial vehicles. The results show a replacement potential of almost one third of the total German annual mileage for these vehicles. The result has a high granularity to allow for detailed emission calculation along different spatial areas as well as vehicle and engine types. Besides a baseline forecast, our method allows for calculating different scenarios regarding policy actions or the future development of important parameters such as energy prices. The results provide insights for policy measures as well as for transport and environmental modeling. - Highlights: • We model the potential German market for electric vehicles using total cost of ownership. • The results show a substitution potential of one third of the total German annual mileage. • Plug-in hybrid drivetrains outperform battery electric ones due to their cost advantages. • Suburbia around large cities is the largest market for EVs. • The first main vehicle categories for EVs are large and medium-sized company cars

Impacts of weathered tire debris on the development of Rana sylvatica larvae.

Science.gov (United States)

Camponelli, Kimberly M; Casey, Ryan E; Snodgrass, Joel W; Lev, Steven M; Landa, Edward R

2009-02-01

Highway runoff has the potential to negatively impact receiving systems including stormwater retention ponds where highway particulate matter can accumulate following runoff events. Tire wear particles, which contain about 1% Zn by mass, make up approximately one-third of the vehicle derived particulates in highway runoff and therefore may serve as a stressor to organisms utilizing retention ponds as habitat. In this study, we focused on the potential contribution of tire debris to Zn accumulation by Rana sylvatica larvae and possible lethal or sublethal impacts resulting from exposure to weathered tire debris during development. Eggs and larvae were exposed to aged sediments (containing either ZnCl2 or tire particulate matter, both providing nominal concentrations of 1000 mg Zn kg(-1)) through metamorphosis. Water column Zn was elevated in both the ZnCl2 and tire treatments relative to the control treatment, indicating that aging allowed Zn leaching from tire debris to occur. Tissue Zn was also elevated for the ZnCl2 and tire treatments indicating that Zn in the treatments was available for uptake by the amphibians. Exposure to both ZnCl2 and tire treatments increased the time for larvae to complete metamorphosis in comparison with controls. We also observed that the longer the organisms took to complete metamorphosis, the smaller their mass at metamorphosis. Our results indicate that Zn leached from aged tire debris is bioavailable to developing R. sylvatica larvae and that exposure to tire debris amended sediments can result in measurable physiological outcomes to wood frogs that may influence population dynamics.

Impacts of weathered tire debris on the development of Rana sylvatica larvae

Science.gov (United States)

Camponelli, K.M.; Casey, R.E.; Snodgrass, J.W.; Lev, S.M.; Landa, E.R.

2009-01-01

Highway runoff has the potential to negatively impact receiving systems including stormwater retention ponds where highway particulate matter can accumulate following runoff events. Tire wear particles, which contain about 1% Zn by mass, make up approximately one-third of the vehicle derived particulates in highway runoff and therefore may serve as a stressor to organisms utilizing retention ponds as habitat. In this study, we focused on the potential contribution of tire debris to Zn accumulation by Rana sylvatica larvae and possible lethal or sublethal impacts resulting from exposure to weathered tire debris during development. Eggs and larvae were exposed to aged sediments (containing either ZnCl2 or tire particulate matter, both providing nominal concentrations of 1000 mg Zn kg-1) through metamorphosis. Water column Zn was elevated in both the ZnCl2 and tire treatments relative to the control treatment, indicating that aging allowed Zn leaching from tire debris to occur. Tissue Zn was also elevated for the ZnCl2 and tire treatments indicating that Zn in the treatments was available for uptake by the amphibians. Exposure to both ZnCl2 and tire treatments increased the time for larvae to complete metamorphosis in comparison with controls. We also observed that the longer the organisms took to complete metamorphosis, the smaller their mass at metamorphosis. Our results indicate that Zn leached from aged tire debris is bioavailable to developing R. sylvatica larvae and that exposure to tire debris amended sediments can result in measurable physiological outcomes to wood frogs that may influence population dynamics. ?? 2008 Elsevier Ltd.

76 FR 76085 - Revisions to the Export Administration Regulations (EAR): Control of Military Vehicles and...

Science.gov (United States)

2011-12-06

... systems to limit vehicle wiring; tire pressure monitoring systems; and data relating to tires (not including run-flats). Although these items might have to be modified for a particular military vehicle, such...

Dynamic simulation of urban hybrid electric vehicles; Dynamische Simulation von Stadthybridfahrzeugen

Energy Technology Data Exchange (ETDEWEB)

Winke, Florian; Bargende, Michael [Stuttgart Univ. (Germany). Inst. fuer Verbrennungsmotoren und Kraftfahrwesen (IVK)

2013-09-15

As a result of the rising requirements on the development process of modern vehicles, simulation models for the prediction of fuel efficiency have become an irreplaceable tool in the automotive industry. Especially for the design of hybrid electric drivetrains, the increasingly short development cycles can only be met by the use of efficient simulation models. At the IVK of the University of Stuttgart, different approaches to simulating the longitudinal dynamics of hybrid electric vehicles were analysed and compared within the presented project. The focus of the investigations was on urban operation. The objective was to develop a hybrid vehicle concept that allows an equitable comparison with pure battery electric vehicles. (orig.)

Clemson University Wind Turbine Drivetrain Test Facility

Energy Technology Data Exchange (ETDEWEB)

Tuten, James Maner [Clemson Univ., SC (United States); Haque, Imtiaz [Clemson Univ., SC (United States); Rigas, Nikolaos [Clemson Univ., SC (United States)

2016-03-30

In November of 2009, Clemson University was awarded a competitive grant from the U.S. Department of Energy to design, build and operate a facility for full-scale, highly accelerated mechanical testing of next-generation wind turbine drivetrain technologies. The primary goal of the project was to design, construct, commission, and operate a state-of-the-art sustainable facility that permits full-scale highly accelerated testing of advanced drivetrain systems for large wind turbines. The secondary goal was to meet the objectives of the American Recovery and Reinvestment Act of 2009, especially in job creation, and provide a positive impact on economically distressed areas in the United States, and preservation and economic recovery in an expeditious manner. The project was executed according to a managed cooperative agreement with the Department of Energy and was an extraordinary success. The resultant new facility is located in North Charleston, SC, providing easy transportation access by rail, road or ship and operates on an open access model such that it is available to the U.S. Wind Industry for research, analysis, and evaluation activities. The 72 m by 97 m facility features two mechanical dynamometer test bays for evaluating the torque and blade dynamic forces experienced by the rotors of wind turbine drivetrains. The dynamometers are rated at 7.5 MW and 15 MW of low speed shaft power and are configured as independent test areas capable of simultaneous operation. All six degrees of freedom, three linear and three rotational, for blade and rotor dynamics are replicated through the combination of a drive motor, speed reduction gearbox and a controllable hydraulic load application unit (LAU). This new LAU setup readily supports accelerated lifetime mechanical testing and load analysis for the entire drivetrain system of the nacelle and easily simulates a wide variety of realistic operating scenarios in a controlled laboratory environment. The development of these

NOISE AS AN INDIRECT CRITERION FOR EVALUATING THE CRITICAL SPEED OF VEHICLE TIRE AT HYDROPLANING

Directory of Open Access Journals (Sweden)

V. Karpenko

2017-12-01

Full Text Available An alternative method for determining the critical rolling speed of automobile tires with various tread patterns during hydroplaning is considered. The critical speed of the car at which the hydroplaning process takes place is determined. This method is based on recording the tire noise emission when driving on a wet road pavement.

A Strain-Based Method to Detect Tires’ Loss of Grip and Estimate Lateral Friction Coefficient from Experimental Data by Fuzzy Logic for Intelligent Tire Development

Directory of Open Access Journals (Sweden)

Jorge Yunta

2018-02-01

Full Text Available Tires are a key sub-system of vehicles that have a big responsibility for comfort, fuel consumption and traffic safety. However, current tires are just passive rubber elements which do not contribute actively to improve the driving experience or vehicle safety. The lack of information from the tire during driving gives cause for developing an intelligent tire. Therefore, the aim of the intelligent tire is to monitor tire working conditions in real-time, providing useful information to other systems and becoming an active system. In this paper, tire tread deformation is measured to provide a strong experimental base with different experiments and test results by means of a tire fitted with sensors. Tests under different working conditions such as vertical load or slip angle have been carried out with an indoor tire test rig. The experimental data analysis shows the strong relation that exists between lateral force and the maximum tensile and compressive strain peaks when the tire is not working at the limit of grip. In the last section, an estimation system from experimental data has been developed and implemented in Simulink to show the potential of strain sensors for developing intelligent tire systems, obtaining as major results a signal to detect tire’s loss of grip and estimations of the lateral friction coefficient.

49 CFR 571.119 - Standard No. 119; New pneumatic tires for motor vehicles with a GVWR of more than 4,536 kilograms...

Science.gov (United States)

2010-10-01

... without interruption. (e) Immediately after running the tire the required time, measure the tire inflation...) Immediately after running the tire the required time, measure the tire inflation pressure. Remove the tire... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 119; New pneumatic tires for motor...

Vehicle Parameter Identification and its Use in Control for Safe Path Following

OpenAIRE

HONG, SANGHYUN

2014-01-01

This thesis develops vehicle parameter identification algorithms, and applies identified parameters to a controller designed for safe path following.A tire-road friction coefficient is estimated using an in-tire accelerometer to measure acceleration signals directly from the tires. The proposed algorithm first determines a tire-road contact patch with a radial acceleration profile.The estimation algorithm is based on tire lateral deflections obtained from lateral acceleration measurements onl...

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXV, I--CATERPILLAR DIESEL ENGINE COOLING SYSTEM D-8 AND 824 MODELS, II--TIRES AND TIRE HARDWARE.

Science.gov (United States)

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE COOLING SYSTEM AND TO PROVIDE A DESCRIPTION OF HEAVY TIRES AND WHEELS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) THEORY OF THE COOLING SYSTEM, (2) COOLING SYSTEM COMPONENTS, (3) MAINTENANCE TIPS (COOLING SYSTEM), (4)…

Vehicle Dynamics and Control

CERN Document Server

Rajamani, Rajesh

2012-01-01

Vehicle Dynamics and Control provides a comprehensive coverage of vehicle control systems and the dynamic models used in the development of these control systems. The control system applications covered in the book include cruise control, adaptive cruise control, ABS, automated lane keeping, automated highway systems, yaw stability control, engine control, passive, active and semi-active suspensions, tire-road friction coefficient estimation, rollover prevention, and hybrid electric vehicle. In developing the dynamic model for each application, an effort is made to both keep the model simple enough for control system design but at the same time rich enough to capture the essential features of the dynamics. A special effort has been made to explain the several different tire models commonly used in literature and to interpret them physically. In the second edition of the book, chapters on roll dynamics, rollover prevention and hybrid electric vehicles have been added, and the chapter on electronic stability co...

First International Workshop on Grid Simulator Testing of Wind Turbine Drivetrains: Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, V.; Link, H.; McDade, M.; Mander, A.; Fox, J. C.; Rigas, N.

2013-11-01

This report summarizes the proceedings of the First International Workshop on Grid Simulator Testing of Wind Turbine Drivetrains, held from June 13 to 14, 2013, at the National Renewable Energy Laboratory's National Wind Technology Center, located south of Boulder, Colorado. The workshop was sponsored by the U.S. Department of Energy and cohosted by the National Renewable Energy Laboratory and Clemson University under ongoing collaboration via a cooperative research and development agreement. The purpose of the workshop was to provide a forum to discuss the research, testing needs, and state-of-the-art apparatuses involved in grid compliance testing of utility-scale wind turbine generators. This includes both dynamometer testing of wind turbine drivetrains ('ground testing') and field testing grid-connected wind turbines. Four sessions followed by discussions in which all attendees of the workshop were encouraged to participate comprised the workshop.

Tire

Science.gov (United States)

Benzing, II, James Alfred (Inventor); Kish, James Christopher (Inventor); Asnani, Vivake Manohar (Inventor)

2012-01-01

A tire includes a plurality of helical springs. Each helical spring includes a first end portion, a second end portion, and an arching middle portion. Each helical spring is interlaced with at least one other helical spring thereby forming a laced toroidal structure extending about an entire circumference of the tire.

49 CFR 574.7 - Information requirements-new tire manufacturers, new tire brand name owners.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Information requirements-new tire manufacturers, new tire brand name owners. 574.7 Section 574.7 Transportation Other Regulations Relating to..., new tire brand name owners. (a)(1) Each new tire manufacturer and each new tire brand name owner...

Effect of Friction Model and Tire Maneuvering on Tire-Pavement Contact Stress

Directory of Open Access Journals (Sweden)

Haichao Zhou

2015-01-01

Full Text Available This paper aims to simulate the effects of different friction models on tire braking. A truck radial tire (295/80R22.5 was modeled and the model was validated with tire deflection. An exponential decay friction model that considers the effect of sliding velocity on friction coefficients was adopted for analyzing braking performance. The result shows that the exponential decay friction model used for evaluating braking ability meets design requirements of antilock braking system (ABS. The tire-pavement contact stress characteristics at various driving conditions (static, free rolling, braking, camber, and cornering were analyzed. It is found that the change of driving conditions has direct influence on tire-pavement contact stress distribution. The results provide the guidance for tire braking performance evaluation.

Improvement of wheel skidder tractive performance by tire inflation pressure and tire chains

OpenAIRE

Stoilov, Stanimir

2007-01-01

The motion resistance ratio, gross traction ratio and net traction ratio of a wheel cable skidder were determined and mathematical models derived for three tire inflation pressure values with or without tire chains on forest road in mountainous conditions. The motion resistance ratio increases with the increase of tire inflation pressure. On the contrary, the gross traction ratio increases with the decrease of tire inflation pressure. However, when the tires are equipped with tire chains t...

Management of used tires, accomplishments in the world, and situation in Serbia

OpenAIRE

Stanojević Dušan D.; Rajković Miloš B.; Tošković Dragan V.

2011-01-01

It is estimated that all over the world there are more than 550 million road vehicles in everyday use. Annually, 1.3 billion used tyres are dismantled from these vehicles due to safety reasons. A small number of these tyres end up reused as second-hand tyres or, after being retreated, as new ones. The rest are end of life tyres which are recycled or used as tire derived fuels under controlled combustion conditions. Modern vehicle tyres are a high-technological product containing, on the...

Vehicle rollover sensor test modeling

NARCIS (Netherlands)

McCoy, R.W.; Chou, C.C.; Velde, R. van de; Twisk, D.; Schie, C. van

2007-01-01

A computational model of a mid-size sport utility vehicle was developed using MADYMO. The model includes a detailed description of the suspension system and tire characteristics that incorporated the Delft-Tyre magic formula description. The model was correlated by simulating a vehicle suspension

Microwave Absorption Characteristics of Tire

Science.gov (United States)

Zhang, Yuzhe; Hwang, Jiann-Yang; Peng, Zhiwei; Andriese, Matthew; Li, Bowen; Huang, Xiaodi; Wang, Xinli

The recycling of waste tires has been a big environmental problem. About 280 million waste tires are produced annually in the United States and more than 2 billion tires are stockpiled, which cause fire hazards and health issues. Tire rubbers are insoluble elastic high polymer materials. They are not biodegradable and may take hundreds of years to decompose in the natural environment. Microwave irradiation can be a thermal processing method for the decomposition of tire rubbers. In this study, the microwave absorption properties of waste tire at various temperatures are characterized to determine the conditions favorable for the microwave heating of waste tires.

PASSIVE DETECTION OF VEHICLE LOADING

Energy Technology Data Exchange (ETDEWEB)

Garrett, A.

2012-01-03

The Digital Imaging and Remote Sensing Laboratory (DIRS) at the Rochester Institute of Technology, along with the Savannah River National Laboratory is investigating passive methods to quantify vehicle loading. The research described in this paper investigates multiple vehicle indicators including brake temperature, tire temperature, engine temperature, acceleration and deceleration rates, engine acoustics, suspension response, tire deformation and vibrational response. Our investigation into these variables includes building and implementing a sensing system for data collection as well as multiple full-scale vehicle tests. The sensing system includes; infrared video cameras, triaxial accelerometers, microphones, video cameras and thermocouples. The full scale testing includes both a medium size dump truck and a tractor-trailer truck on closed courses with loads spanning the full range of the vehicle's capacity. Statistical analysis of the collected data is used to determine the effectiveness of each of the indicators for characterizing the weight of a vehicle. The final sensing system will monitor multiple load indicators and combine the results to achieve a more accurate measurement than any of the indicators could provide alone.

Passive detection of vehicle loading

Science.gov (United States)

McKay, Troy R.; Salvaggio, Carl; Faulring, Jason W.; Salvaggio, Philip S.; McKeown, Donald M.; Garrett, Alfred J.; Coleman, David H.; Koffman, Larry D.

2012-01-01

The Digital Imaging and Remote Sensing Laboratory (DIRS) at the Rochester Institute of Technology, along with the Savannah River National Laboratory is investigating passive methods to quantify vehicle loading. The research described in this paper investigates multiple vehicle indicators including brake temperature, tire temperature, engine temperature, acceleration and deceleration rates, engine acoustics, suspension response, tire deformation and vibrational response. Our investigation into these variables includes building and implementing a sensing system for data collection as well as multiple full-scale vehicle tests. The sensing system includes; infrared video cameras, triaxial accelerometers, microphones, video cameras and thermocouples. The full scale testing includes both a medium size dump truck and a tractor-trailer truck on closed courses with loads spanning the full range of the vehicle's capacity. Statistical analysis of the collected data is used to determine the effectiveness of each of the indicators for characterizing the weight of a vehicle. The final sensing system will monitor multiple load indicators and combine the results to achieve a more accurate measurement than any of the indicators could provide alone.

Post-consumer tires back into new tires: de-vulcanization and re-utilization of passenger car tires

OpenAIRE

Saiwari, Sitisaiyidah

2013-01-01

Enabling recycling loops for used passenger car tires is a challenge and an opportunity. The challenge lies in the presence of SBR as the main elastomer in this type of tires, which makes this material difficult to reclaim due to the tendency of the elastomer chain fragments to re-combine. The opportunity lies in the wide availability of the material and in the fact that passenger car tires form a huge potential market for recycled rubber. The aim of this study is to develop a de-vulcanizatio...

A Tire Air Maintenance Technology

Science.gov (United States)

Pierce, Alan

2012-01-01

Improperly inflated car tires can reduce gas mileage and car performance, speed up tire wear, and even cause a tire to blow out. The AAA auto club recommends that someone check the air pressure of one's car's tires at least once a month. Wouldn't it be nice, though, if someone came up with a tire pressure-monitoring system that automatically kept…

Study on Active Suppression Control of Drivetrain Oscillations in an Electric Vehicle

Science.gov (United States)

Huang, Lei; Cui, Ying

2017-07-01

Due to the low damping in a central driven electric vehicle and lack of passive damping mechanisms as compared with a conventional vehicle, the vehicle may endure torsional vibrations which may deteriorates the vehicle’s drivability. Thus active damping control strategy is required to reduce the undesirable oscillations in an EV. In this paper, the origin of the vibration and the design of a damping control method to suppress such oscillations to improve the drivability of an EV are studied. The traction motor torque that is given by the vehicle controller is adjusted according to the acceleration rate of the motor speed to attenuate the resonant frequency. Simulations and experiments are performed to validate the system. The results show that the proposed control system can effectively suppress oscillations and hence improve drivability.

Tire inspection machine presenting an X-ray image of the entire width of the tire

International Nuclear Information System (INIS)

1975-01-01

An X-ray machine for production line inspection of tires places each tire in turn with one sector of the tire inside of a U-shaped arrangement of three fluorescent screens so that one screen faces the tread and the other two face the sides of the tire. An X-ray source inside the bead circle of the tire produces X-ray shadow pictures on the screens, which are separately viewed by a video camera, with an image of the picture on each screen transferred to a third of the target of a storage tube, so that a composite image of the entire width of the tire sector can be displayed on a picture tube. The tire is rotated step-wise for display of still pictures of every sector of the tire. (Auth.)

Tire-road noise: an experimental study of tire and road design parameters

OpenAIRE

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire manufacturers. Usually, the parameters influencing exterior tire-road noise are often examined separately, whereas it is the tire-road interaction which obviously causes the actual noise. An integral...

Tire safety : everything rides on it

Science.gov (United States)

2008-01-01

This booklet presents a comprehensive overview of tire safety, including information on the following topics: basic tire maintenance; Uniform Tire Quality Grading System; fundamental characteristics of tires; and tire safety tips.

Estimation of vertical load on a tire from contact patch length and its use in vehicle stability control

OpenAIRE

Dhasarathy, Deepak

2010-01-01

The vertical load on a moving tire was estimated by using accelerometers attached to the inner liner of a tire. The acceleration signal was processed to obtain the contact patch length created by the tire on the road surface. Then an appropriate equation relating the patch length to the vertical load is used to calculate the load. In order to obtain the needed data, tests were performed on a flat-track test machine at the Goodyear Innovation Center in Akron, Ohio; tests were also conducted on...

77 FR 10615 - Cooper Tire & Rubber Tire Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-02-22

... tread wear, temperature, and traction ratings, to assess performance capabilities of various tires. In...-0054; Notice 2] Cooper Tire & Rubber Tire Company, Grant of Petition for Decision of Inconsequential...: Cooper Tire & Rubber Tire Company, (Cooper) \\1\\, has determined that approximately 6,964 passenger car...

Effect of wheelchair mass, tire type and tire pressure on physical strain and wheelchair propulsion technique.

Science.gov (United States)

de Groot, Sonja; Vegter, Riemer J K; van der Woude, Lucas H V

2013-10-01

The purpose of this study was to evaluate the effect of wheelchair mass, solid vs. pneumatic tires and tire pressure on physical strain and wheelchair propulsion technique. 11 Able-bodied participants performed 14 submaximal exercise blocks on a treadmill with a fixed speed (1.11 m/s) within 3 weeks to determine the effect of tire pressure (100%, 75%, 50%, 25% of the recommended value), wheelchair mass (0 kg, 5 kg, or 10 kg extra) and tire type (pneumatic vs. solid). All test conditions (except pneumatic vs. solid) were performed with and without instrumented measurement wheels. Outcome measures were power output (PO), physical strain (heart rate (HR), oxygen uptake (VO2), gross mechanical efficiency (ME)) and propulsion technique (timing, force application). At 25% tire pressure PO and subsequently VO2 were higher compared to 100% tire pressure. Furthermore, a higher tire pressure led to a longer cycle time and contact angle and subsequently lower push frequency. Extra mass did not lead to an increase in PO, physical strain or propulsion technique. Solid tires led to a higher PO and physical strain. The solid tire effect was amplified by increased mass (tire × mass interaction). In contrast to extra mass, tire pressure and tire type have an effect on PO, physical strain or propulsion technique of steady-state wheelchair propulsion. As expected, it is important to optimize tire pressure and tire type. Copyright © 2013 IPEM. Published by Elsevier Ltd. All rights reserved.

76 FR 28502 - Cooper Tire & Rubber Tire Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2011-05-17

...-0054; Notice 1] Cooper Tire & Rubber Tire Company, Receipt of Petition for Decision of Inconsequential Noncompliance Cooper Tire & Rubber Tire Company, (Cooper),\\1\\ has determined that approximately 6,964 passenger car replacement tires manufactured between January 23, 2011 and March 26, 2011, do not fully comply...

Analysis of automotive tire construction. Jidosha tire no kozo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Ishihara, K. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

1993-06-15

This paper introduces features and trends of analyzing performance and construction of automotive tires. Tires are demanded of high durability, high motion performance, good comfort performance for vibration and noise, and low fuel consumption performance. A feature of analyzing the construction is to execute a modelling assuming that a tire has air-rigid flexible structure and rubber materials show hyperelastic behavior, hypothesizing a strain energy density function. In addition, a tire is highly incompressible. Visco elasticity and anti-friction performance are also important points. Rubber and cord layers have elastic characteristic of three-dimensional perpendicular anisotropy as well as non-linearity with which characteristics change according to transformation. A structural analysis must cover from static analysis to steady dynamic analysis, non-steady dynamic analysis, and eigenvalue analysis. Thermal analysis of tires simulates phenomena by combining dynamical analysis with thermal analysis. Super-computers have now come to be used for formulating equilibrium equations using finite element methods, developing finite elements, and performing heat or visco elasticity analysis and applied analysis. 35 refs., 3 figs.

Component sizing optimization of plug-in hybrid electric vehicles

International Nuclear Information System (INIS)

Wu, Xiaolan; Cao, Binggang; Li, Xueyan; Xu, Jun; Ren, Xiaolong

2011-01-01

Plug-in hybrid electric vehicles (PHEVs) are considered as one of the most promising means to improve the near-term sustainability of the transportation and stationary energy sectors. This paper describes a methodology for the optimization of PHEVs component sizing using parallel chaos optimization algorithm (PCOA). In this approach, the objective function is defined so as to minimize the drivetrain cost. In addition, the driving performance requirements are considered as constraints. Finally, the optimization process is performed over three different all electric range (AER) and two types of batteries. The results from computer simulation show the effectiveness of the approach and the reduction in drivetrian cost while ensuring the vehicle performance.

Processing methods, characteristics and adsorption behavior of tire derived carbons: a review.

Science.gov (United States)

Saleh, Tawfik A; Gupta, Vinod Kumar

2014-09-01

The remarkable increase in the number of vehicles worldwide; and the lack of both technical and economical mechanisms of disposal make waste tires to be a serious source of pollution. One potential recycling process is pyrolysis followed by chemical activation process to produce porous activated carbons. Many researchers have recently proved the capability of such carbons as adsorbents to remove various types of pollutants including organic and inorganic species. This review attempts to compile relevant knowledge about the production methods of carbon from waste rubber tires. The effects of various process parameters including temperature and heating rate, on the pyrolysis stage; activation temperature and time, activation agent and activating gas are reviewed. This review highlights the use of waste-tires derived carbon to remove various types of pollutants like heavy metals, dye, pesticides and others from aqueous media. Copyright © 2014 Elsevier B.V. All rights reserved.

Deep learning for automated drivetrain fault detection

DEFF Research Database (Denmark)

Bach-Andersen, Martin; Rømer-Odgaard, Bo; Winther, Ole

2018-01-01

A novel data-driven deep-learning system for large-scale wind turbine drivetrain monitoring applications is presented. It uses convolutional neural network processing on complex vibration signal inputs. The system is demonstrated to learn successfully from the actions of human diagnostic experts...... the fleet-wide diagnostic model performance. The analysis also explores the time dependence of the diagnostic performance, providing a detailed view of the timeliness and accuracy of the diagnostic outputs across the different architectures. Deep architectures are shown to outperform the human analyst...... as well as shallow-learning architectures, and the results demonstrate that when applied in a large-scale monitoring system, machine intelligence is now able to handle some of the most challenging diagnostic tasks related to wind turbines....

Near term hybrid passenger vehicle development program, phase 1

Science.gov (United States)

1980-01-01

Missions for hybrid vehicles that promise to yield high petroleum impact were identified and a preliminary design, was developed that satisfies the mission requirements and performance specifications. Technologies that are critical to successful vehicle design, development and fabrication were determined. Trade-off studies to maximize fuel savings were used to develop initial design specifications of the near term hybrid vehicle. Various designs were "driven" through detailed computer simulations which calculate the petroleum consumption in standard driving cycles, the petroleum and electricity consumptions over the specified missions, and the vehicle's life cycle costs over a 10 year vehicle lifetime. Particular attention was given to the selection of the electric motor, heat engine, drivetrain, battery pack and control system. The preliminary design reflects a modified current compact car powered by a currently available turbocharged diesel engine and a 24 kW (peak) compound dc electric motor.

Research and application of online measurement system of tire tread profile in automobile tire production

Science.gov (United States)

Wang, Pengyao; Chen, Xiangguang; Yang, Kai; Liu, Xuejiao

2017-01-01

To improve the measuring efficiency of width and thickness of tire tread in the process of automobile tire production, the actual condition for the tire production process is analyzed, and a fast online measurement system based on moving tire tread of tire specifications is established in this paper. The coordinate data of tire tread profile is acquired by 3D laser sensor, and we use C# language for programming which is an object-oriented programming language to complete the development of client program. The system with laser sensor can provide real-time display of tire tread profile and the data to require in the process of tire production. Experimental results demonstrate that the measuring precision of the system is <= 1mm, it can meet the measurement requirements of the production process, and the system has the characteristics of convenient installation and testing, system stable operation.

Stereo Vision Inside Tire

Science.gov (United States)

2015-08-21

1 Stereo Vision Inside Tire P.S. Els C.M. Becker University of Pretoria W911NF-14-1-0590 Final...Stereo Vision Inside Tire 5a. CONTRACT NUMBER W911NF-14-1-0590 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Prof PS Els CM...on the development of a stereo vision system that can be mounted inside a rolling tire , known as T2-CAM for Tire -Terrain CAMera. The T2-CAM system

Toxicity of tire wear particle leachate to the marine macroalga, Ulva lactuca

Energy Technology Data Exchange (ETDEWEB)

Turner, Andrew, E-mail: aturner@plymouth.ac.u [School of Geography, Earth and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Rice, Lynsey [School of Geography, Earth and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

2010-12-15

Tire wear particles filed from the treads of end-of-life vehicle tires have been added to sea water to examine the release of Zn and the toxicity of the resulting leachate and dilutions thereof to the marine macroalga, Ulva lactuca. Zinc release appeared to be diffusion-controlled, with a conditional rate constant of 5.4 {mu}g[L(h){sup 1/2}]{sup -1}, and about 1.6% of total Zn was released after 120 h incubation. Exposure to increasing concentrations of leachate resulted in a non-linear reduction in the efficiency of photochemical energy conversion of U. lactuca and, with the exception of the undiluted leachate, increasing accumulation of Zn. Phototoxicity was significantly lower on exposure to equivalent concentrations of Zn added as Zn(NO{sub 3}){sub 2}, suggesting that organic components of leachate are largely responsible for the overall toxicity to the alga. Given the ubiquity and abundance of TWP in urban coastal sediments, the generation, biogeochemistry and toxicity of tire leachate in the marine setting merit further attention. - Tire wear leachate is toxic to Ulva lactuca and zinc is a potential bioindicator of leachate contamination in urban marine systems.

Post-consumer tires back into new tires: de-vulcanization and re-utilization of passenger car tires

NARCIS (Netherlands)

Saiwari, Sitisaiyidah

2013-01-01

Enabling recycling loops for used passenger car tires is a challenge and an opportunity. The challenge lies in the presence of SBR as the main elastomer in this type of tires, which makes this material difficult to reclaim due to the tendency of the elastomer chain fragments to re-combine. The

Numerical Simulations of the Aeroelastic Behavior of Large Horizontal-Axis Wind Turbines: The Drivetrain Case

DEFF Research Database (Denmark)

Gebhardt, Cristian; Veluri, Badrinath; Preidikman, Sergio

2010-01-01

In this work an aeroelastic model that describes the interaction between aerodynamics and drivetrain dynamics of a large horizontal–axis wind turbine is presented. Traditional designs for wind turbines are based on the output of specific aeroelastic simulation codes. The output of these codes giv...

Method and apparatus for inspecting tires

International Nuclear Information System (INIS)

Fox, R.L.T.

1975-01-01

A method and apparatus for inspecting tires by the use of x-rays is disclosed in which a tire is advanced to an inspection station, engaged along opposite bead rims and inflated to axially spread the bead rims and side walls. An x-ray source is advanced axially into the tire and the tire is eccentrically rotated relative to the x-ray source to enable radial positioning of the source relative to the tire near the tire bead rim diameter without requiring radial movement of the x-ray source. The x-ray source produces an x-ray beam which sweeps about the interior of the expanded tire from bead rim to bead rim while the tire is rotated about its centerline. An x-ray detection system detects x-rays which have penetrated the wall and produces inspection information concerning the tire construction. (Patent Office Record)

Drive-train condition monitoring for offshore wind and tidal turbines

DEFF Research Database (Denmark)

Roshanmanesh, Sanaz; Hayati, Farzad; Kappatos, Vassilios

are subject to several damage mechanisms which may lead to various failure modes including gear teeth damage, cracking of the gearbox case, shaft misalignment, wear or looseness of torque arm, loss of lubricant in lubrication system, bearing damage and shaft failure. This paper presents an experimental...... investigation assessing the effectiveness of Acoustic Emission (AE) and vibration analysis (VA) in identifying different types of faults in wind and tidal turbine drive-trains. Additionally the application of advanced signal processing techniques, such as Spectral Kurtosis (SK) and wavelet analysis have been...

Loading Effect on Tire Noise Radiation

OpenAIRE

Cao, Rui; Bolton, J Stuart

2016-01-01

Noise radiated by tires is a prominent noise pollution source and it is affected by many different parameters. Here, the effect of static load on tire noise radiation in a laboratory environment was investigated. The measurement was conducted by using the Tire Pavement Testing Apparatus (TPTA), on which a loaded tire can be run at speeds up to 50 km/hr; the tire noise was measured using a nearfield microphone method. The tire loading was varied from 500 to 900 pounds, and several different co...

Runway drainage characteristics related to tire friction performance

Science.gov (United States)

Yager, Thomas J.

1991-01-01

The capability of a runway pavement to rapidly drain water buildup during periods of precipitation is crucial to minimize tire hydroplaning potential and maintain adequate aircraft ground operational safety. Test results from instrumented aircraft, ground friction measuring vehicles, and NASA Langley's Aircraft Landing Dynamics Facility (ALDF) track have been summarized to indicate the adverse effects of pavement wetness conditions on tire friction performance. Water drainage measurements under a range of rainfall rates have been evaluated for several different runway surface treatments including the transversely grooved and longitudinally grinded concrete surfaces at the Space Shuttle Landing Facility (SLF) runway at NASA Kennedy Space Center in Florida. The major parameters influencing drainage rates and extent of flooding/drying conditions are identified. Existing drainage test data are compared to a previously derived empirical relationship and the need for some modification is indicated. The scope of future NASA Langley research directed toward improving empirical relationships to properly define runway drainage capability and consequently, enhance aircraft ground operational safety, is given.

Component sizing optimization of plug-in hybrid electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Wu, Xiaolan; Cao, Binggang; Li, Xueyan; Xu, Jun; Ren, Xiaolong [School of Mechanical Engineering, Xi' an Jiaotong University, Xi' an, 710049 (China)

2011-03-15

Plug-in hybrid electric vehicles (PHEVs) are considered as one of the most promising means to improve the near-term sustainability of the transportation and stationary energy sectors. This paper describes a methodology for the optimization of PHEVs component sizing using parallel chaos optimization algorithm (PCOA). In this approach, the objective function is defined so as to minimize the drivetrain cost. In addition, the driving performance requirements are considered as constraints. Finally, the optimization process is performed over three different all electric range (AER) and two types of batteries. The results from computer simulation show the effectiveness of the approach and the reduction in drivetrian cost while ensuring the vehicle performance. (author)

Tire-soil interaction model for turning (steered) tires

Science.gov (United States)

Karafiath, L. L.

1985-07-01

A review of the experimental information on the development of lateral forces on tires traveling at an angle to their center plane is presented and the usefulness of the consideration of the lateral forces for the development of an analytical model is evaluated. Major components of the lateral force have been identified as the forces required to balance the tractive force and the drawbar pull vectorially. These are the shear stresses developing in the contact area and the horizontal component of the normal stresses acting on the in-ground portion or the curved side walls of the tire. The tire-soil interaction model for steady state straight travel has been expanded to include the necessary algorithms for the calculation of these lateral forces. The pattern of tractive force-slip and longitudinal-lateral force relationships is in general agreement with experiments.

78 FR 2236 - Federal Motor Vehicle Safety Standards; New Pneumatic Tires for Motor Vehicles With a GVWR of...

Science.gov (United States)

2013-01-10

... have been almost completely replaced by radial tires in the U.S.; however, a small market for bias... impact of this rulemaking action under Executive Order 12866, Executive Order 13563, and the Department... = Force in newtons (N), and P = Penetration in millimeters (mm), or; (2) W = (F x P)/2 [[Page 2239

49 CFR 571.500 - Standard No. 500; Low-speed vehicles.

Science.gov (United States)

2010-10-01

... replacement of any component is allowed after the start of the first performance test. S6.3.3. Tire inflation.... General test conditions. Each vehicle must meet the performance limit specified in S5(a) under the... standard reference test tire that meets the specifications of American Society for Testing and Materials...

Multi-path transportation futures study : vehicle characterization and scenario analyses.

Energy Technology Data Exchange (ETDEWEB)

Plotkin, S. E.; Singh, M. K.; Energy Systems; TA Engineering; ORNL

2009-12-03

Projecting the future role of advanced drivetrains and fuels in the light vehicle market is inherently difficult, given the uncertainty (and likely volatility) of future oil prices, inadequate understanding of likely consumer response to new technologies, the relative infancy of several important new technologies with inevitable future changes in their performance and costs, and the importance - and uncertainty - of future government marketplace interventions (e.g., new regulatory standards or vehicle purchase incentives). This Multi-Path Transportation Futures (MP) Study has attempted to improve our understanding of this future role by examining several scenarios of vehicle costs, fuel prices, government subsidies, and other key factors. These are projections, not forecasts, in that they try to answer a series of 'what if' questions without assigning probabilities to most of the basic assumptions.

Probabilistic Modeling of Wind Turbine Drivetrain Components

DEFF Research Database (Denmark)

Rafsanjani, Hesam Mirzaei

Wind energy is one of several energy sources in the world and a rapidly growing industry in the energy sector. When placed in offshore or onshore locations, wind turbines are exposed to wave excitations, highly dynamic wind loads and/or the wakes from other wind turbines. Therefore, most components...... in a wind turbine experience highly dynamic and time-varying loads. These components may fail due to wear or fatigue, and this can lead to unplanned shutdown repairs that are very costly. The design by deterministic methods using safety factors is generally unable to account for the many uncertainties. Thus......, a reliability assessment should be based on probabilistic methods where stochastic modeling of failures is performed. This thesis focuses on probabilistic models and the stochastic modeling of the fatigue life of the wind turbine drivetrain. Hence, two approaches are considered for stochastic modeling...

Zinc Leaching from Tire Crumb Rubber

Science.gov (United States)

Rhodes, E. P.; Ren, J.; Mays, D. C.

2010-12-01

Recent estimates indicate that more than 2 billion scrap tires are currently stockpiled in the United States and approximately 280 million more tires are added annually. Various engineering applications utilize recycled tires in the form of shredded tire crumb rubber. However, the use of tire crumb rubber may have negative environmental impacts, especially when the rubber comes into contact with water. A review of the literature indicates that leaching of zinc from tire crumb rubber is the most significant water quality concern associated with using this material. Zinc is generally used in tire manufacturing, representing approximately 1.3% of the final product by mass. This study will report results from the U.S. Environmental Protection Agency’s (EPA’s) Synthetic Precipitation Leaching Procedure, batch leaching tests, and column leaching tests performed to quantify the process by which zinc leaches from tire crumb rubber into water. Results are interpreted with a first-order kinetic attachment/detachment model, implemented with the U.S. Agricultural Research Service software HYDRUS-1D, in order to determine the circumstances when zinc leaching from tire crumb rubber would be expected to comply with the applicable discharge limits. One potential application for recycled tires is replacing sand with tire crumb rubber in granular media filters used for stormwater pollution control. For this to be a viable application, the total zinc in the stormwater discharge must be below the EPA’s benchmark value of 0.117 mg/L.

Effect of Friction Model and Tire Maneuvering on Tire-Pavement Contact Stress

OpenAIRE

Haichao Zhou; Guolin Wang; Yangmin Ding; Jian Yang; Chen Liang; Jing Fu

2015-01-01

This paper aims to simulate the effects of different friction models on tire braking. A truck radial tire (295/80R22.5) was modeled and the model was validated with tire deflection. An exponential decay friction model that considers the effect of sliding velocity on friction coefficients was adopted for analyzing braking performance. The result shows that the exponential decay friction model used for evaluating braking ability meets design requirements of antilock braking system (ABS). The ti...

Pressure Control In A Tyre Of Moving Vehicle

Science.gov (United States)

Gawande, Kshitij P.; Jawanjal, Vaishakh A.

2012-08-01

We always try to make everything perfect around us and there is major problem still remaining in our automobiles, a puncture in a tire while running. We have developed tubeless tires but thatís not a perfect solution, so there is a serious need of improvement in this area. In this paper the compressed air is used to maintain the pressure in the tire using pneumatic pipes. This is a very basic concept which uses compressor power to maintain the pressure of a tire, while running using pressure gauges and leak proof connection. This technique allows us to drive a punctured vehicle which increases safety, comfort & saves time. This paper suggests a new technique towards one more improvement in our automobile industry.

A Control Strategy for Mode Transition with Gear Shifting in a Plug-In Hybrid Electric Vehicle

Directory of Open Access Journals (Sweden)

Kyuhyun Sim

2017-07-01

Full Text Available The mode transition from electric propulsion mode to hybrid propulsion mode is important with regard to the power management strategy of plug-in hybrid electric vehicles (PHEVs. This is because mode transitions can occur frequently depending on the power management strategies and driving cycles, and because inadequate mode transitions worsen the fuel efficiency and drivability. A pre-transmission parallel PHEV uses a clutch between the internal combustion engine (ICE and the electric motor (EM to connect or disconnect the power source of the ICE for a mode transition. The mode transition requires additional energy consumption for clutch speed synchronization, and is accompanied by a drivetrain shock due to clutch engagement. This paper proposes a control strategy for the mode transition with gear-shifting to resolve the problems of energy consumption and drivetrain shock. Through the development of a PHEV performance simulator, we analyze the mode transition characteristics and propose a control strategy considering the vehicle acceleration and gear state. The control strategy reduces the duration required for the mode transition by moving the start time of the mode transition. This helps to improve energy efficiency while maintaining adequate drivability.

Pavement type and wear condition classification from tire cavity acoustic measurements with artificial neural networks.

Science.gov (United States)

Masino, Johannes; Foitzik, Michael-Jan; Frey, Michael; Gauterin, Frank

2017-06-01

Tire road noise is the major contributor to traffic noise, which leads to general annoyance, speech interference, and sleep disturbances. Standardized methods to measure tire road noise are expensive, sophisticated to use, and they cannot be applied comprehensively. This paper presents a method to automatically classify different types of pavement and the wear condition to identify noisy road surfaces. The methods are based on spectra of time series data of the tire cavity sound, acquired under normal vehicle operation. The classifier, an artificial neural network, correctly predicts three pavement types, whereas there are few bidirectional mis-classifications for two pavements, which have similar physical characteristics. The performance measures of the classifier to predict a new or worn out condition are over 94.6%. One could create a digital map with the output of the presented method. On the basis of these digital maps, road segments with a strong impact on tire road noise could be automatically identified. Furthermore, the method can estimate the road macro-texture, which has an impact on the tire road friction especially on wet conditions. Overall, this digital map would have a great benefit for civil engineering departments, road infrastructure operators, and for advanced driver assistance systems.

Estimation of vehicle’s vertical and lateral tire forces considering road angle and road irregularity

OpenAIRE

JIANG , KUN; Pavelescu , Adina; Correa Victorino , Alessandro; Charara , Ali

2014-01-01

International audience; Vehicle dynamics is an essential topic in development of safety driving systems. These complex and integrated control units require precise information about vehicle dynamics, especially, tire/road contact forces. Nevertheless, it is lacking an effective and low-cost sensor to measure them directly. Therefore, this study presents a new method to estimate these parameters by using observer technologies and low-cost sensors which are available on the passenger cars in re...

Vehicle Impact Testing of Snow Roads at McMurdo Station, Antarctica

Science.gov (United States)

2014-06-01

especially during warm weather when their high flotation tires al- low greater over-snow mobility. Table 2. Test vehicle information. Vehicle Vehicle...potential danger to the vehicle and pax 16 ERDC/CRREL TR-14-9 51 GO SLOWTI-U<OtJG-ISBTFOR YOLH?. SAFETY LANE C SCOTT BASE TRANSIT/ONTO SILVER

Rubber tire leachates in the aquatic environment.

Science.gov (United States)

Evans, J J

1997-01-01

Tires have a deleterious effect on the environment. This review discusses the background of scrap tires discarded in the environment, including tire composition, adverse environmental effects, threats to public health and safety, and solid waste management. Despite the widespread use of scrap tires in environmental applications, both land-based and aquatic, data on the indicators of environmental degradation are extremely scarce. Indicators of environmental degradation include analysis of chemicals within the water and sediment, analysis of contaminants within organisms, and analysis of the biological effects of these compounds on plants, animals, microbes, and organelles. Although these indicators are most useful when used in parallel, a review of the available information on chemical characterization of tire leachate from tire storage facilities, manufacturing, usage in recycling applications, and toxicity exposure studies, of vegetation surveys from waste tire areas and reviews of mammalian tire product toxicity, and of toxicity, mutagenicity, and carcinogenicity of tire exposure in experimental aquatic animals, microbes, and organelles is presented. The major characteristics of these studies are discussed in specific sections. The "Discussion and Conclusions" section discusses and summarizes the biological effects and chemical characterization of tire leachates. A global environmental perspective is included to improve our understanding of the deficiency of the current knowledge of tire leachate toxicity from various sources and to encourage interdisciplinary studies to establish the pattern of pollution associated with waste tire management.

77 FR 54836 - Federal Motor Vehicle Safety Standards

Science.gov (United States)

2012-09-06

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 571 Federal Motor Vehicle Safety Standards CFR Correction 0 In Title 49 of the Code of Federal Regulations... read as follows: Sec. 571.119 Standard No. 119; New pneumatic tires for motor vehicles with a GVWR of...

Assessment of wind turbine drive-train fatigue loads under torsional excitation

DEFF Research Database (Denmark)

Gallego Calderon, Juan Felipe; Natarajan, Anand

2015-01-01

allows the computation of the bearing and gear-mesh loads. The proposed models are validated by experiments from a 750 kW test-rig. The drive-train model is configured for a 5 MW power capacity and coupled to the corresponding wind turbine and load simulations are carried out under turbulent wind...... model is used in comparison to a simplified approach for load calculation. It is found that some of the wind turbine modes can have negative consequences on the life-time of the planetary bearings. © 2015 Elsevier Ltd. All rights reserved....

Reprocessing and reuse of waste tire rubber to solve air-quality related problems

Science.gov (United States)

Lehmann, C.M.B.; Rostam-Abadi, M.; Rood, M.J.; Sun, Jielun

1998-01-01

There is a potential for using waste tire rubber to make activated-carbon adsorbents for air-quality control applications. Such an approach provides a recycling path for waste tires and the production of new adsorbents from a low-cost waste material. Tire-derived activated carbons (TDACs) were prepared from waste tires. The resulting products are generally mesoporous, with N2-BET specific surface areas ranging from 239 to 1031 m2/g. TDACs were tested for their ability to store natural gas and remove organic compounds and mercury species from gas streams. TDACs are able to achieve 36% of the recommended adsorbed natural gas (methane) storage capacity for natural-gas-fueled vehicles. Equilibrium adsorption capacities for CH4 achieved by TDACs are comparable to Calgon BPL, a commercially available activated-carbon adsorbent. The acetone adsorption capacity for a TDAC is 67% of the adsorption capacity achieved by BPL at 1 vol % acetone. Adsorption capacities of mercury in simulated flue-gas streams are, in general, larger than adsorption capacities achieved by coal-derived activated carbons (CDACs) and BPL. Although TDACs may not perform as well as commercial adsorbents in some air pollution control applications, the potential lower cost of TDACS should be considered when evaluating economics.

The Porsche Panamera S E-Hybrid drivetrain; Der Antriebsstrang des Porsche Panamera S E-Hybrid

Energy Technology Data Exchange (ETDEWEB)

Semmler, D.; Kerner, J.; Spiegel, L.; Bitsche, O.; Rauner, T.; Stache, I.; Marques, M. [Dr. Ing. h.c. F. Porsche AG, Weissach (Germany)

2013-08-01

With the new Panamera S E-Hybrid, Porsche presents the first standard plug-in hybrid concept for the luxury sector. The drivetrain represents a consistent further development of the full-hybrid vehicles already successful on the market. However, it has been updated to achieve the lowest possible fuel consumption and to meet future emission laws before they even take effect. It was possible to increase the performance and efficiency of the hybrid components, significantly improving both electric performance as well as the electric range. A large part of that is due to the new electric machine. In the same installation space, we have managed to more than double the power to 70 kW. A new intelligent operating strategy also allows us to meet the EU6 exhaust gas limits. In addition to the efficiency improvement measures, the lithium-ion battery with its 9.4 kWh capacity especially contributes to the car's enhanced range. Thanks to the higher energy density of the new cell technology, the battery only needs a little more installation space in comparison with the Panamera S Hybrid. In pure electric operation, the vehicle reaches a top speed of 135 km/h (limited) and has an electric range of 36 kilometres in the NEDC profile. Typical Porsche performance is provided by the system power of 416 hp (306 kW). In NEDC standard consumption, the E-Hybrid's 3.1 l/100 km and CO{sub 2} emissions of 71 g/km have stayed attractively economical. (orig.)

Tire Development for Effective Transportation and Utilization of Used Tires, CRADA 01-N044, Final Report

Energy Technology Data Exchange (ETDEWEB)

Susan M. Maley

2004-03-31

Scrap tires represent a significant disposal and recycling challenge for the United States. Over 280 million tires are generated on an annual basis, and several states have large stockpiles or abandoned tire piles that are slated for remediation. While most states have programs to address the accumulation and generation of scrap tires, most of these states struggle with creating and sustaining recycling or beneficial end use markets. One of the major issues with market development has been the costs associated with transporting and processing the tires into material for recycling or disposal. According to a report by the Rubber Manufactures Association tire-derived fuel (TDF) represents the largest market for scrap tires, and approximately 115 million tires were consumed in 2001 as TDF (U.S. Scrap Tire Markets, 2001, December 2002, www.rma.org/scraptires). This market is supported primarily by cement kilns, followed by various industries including companies that operate utility and industrial boilers. However the use of TDF has not increased and the amount of TDF used by boiler operators has declined. The work completed through this cooperative research and development agreement (CRADA) has shown the potential of a mobile tire shredding unit to economically produce TDF and to provide an alterative low cost fuel to suitable coal-fired power systems. This novel system addresses the economic barriers by processing the tires at the retailer, thereby eliminating the costs associated with hauling whole tires. The equipment incorporated into the design allow for small 1-inch chunks of TDF to be produced in a timely fashion. The TDF can then be co-fired with coal in suitable combustion systems, such as a fluidized bed. Proper use of TDF has been shown to boost efficiency and reduce emissions from power generation systems, which is beneficial to coal utilization in existing power plants. Since the original scope of work outlined in the CRADA could not be completed because

49 CFR 574.5 - Tire identification requirements.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Tire identification requirements. 574.5 Section... SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) TIRE IDENTIFICATION AND RECORDKEEPING § 574.5 Tire identification requirements. Each tire manufacturer shall conspicuously label on one...

Current Research in Aircraft Tire Design and Performance

Science.gov (United States)

Tanner, J. A.; Mccarthy, J. L.; Clark, S. K.

1981-01-01

A review of the tire research programs which address the various needs identified by landing gear designers and airplane users is presented. The experimental programs are designed to increase tire tread lifetimes, relate static and dynamic tire properties, establish the tire hydroplaning spin up speed, study gear response to tire failures, and define tire temperature profiles during taxi, braking, and cornering operations. The analytical programs are aimed at providing insights into the mechanisms of heat generation in rolling tires and developing the tools necessary to streamline the tire design process and to aid in the analysis of landing gear problems.

Processing Satellite Imagery To Detect Waste Tire Piles

Science.gov (United States)

Skiles, Joseph; Schmidt, Cynthia; Wuinlan, Becky; Huybrechts, Catherine

2007-01-01

A methodology for processing commercially available satellite spectral imagery has been developed to enable identification and mapping of waste tire piles in California. The California Integrated Waste Management Board initiated the project and provided funding for the method s development. The methodology includes the use of a combination of previously commercially available image-processing and georeferencing software used to develop a model that specifically distinguishes between tire piles and other objects. The methodology reduces the time that must be spent to initially survey a region for tire sites, thereby increasing inspectors and managers time available for remediation of the sites. Remediation is needed because millions of used tires are discarded every year, waste tire piles pose fire hazards, and mosquitoes often breed in water trapped in tires. It should be possible to adapt the methodology to regions outside California by modifying some of the algorithms implemented in the software to account for geographic differences in spectral characteristics associated with terrain and climate. The task of identifying tire piles in satellite imagery is uniquely challenging because of their low reflectance levels: Tires tend to be spectrally confused with shadows and deep water, both of which reflect little light to satellite-borne imaging systems. In this methodology, the challenge is met, in part, by use of software that implements the Tire Identification from Reflectance (TIRe) model. The development of the TIRe model included incorporation of lessons learned in previous research on the detection and mapping of tire piles by use of manual/ visual and/or computational analysis of aerial and satellite imagery. The TIRe model is a computational model for identifying tire piles and discriminating between tire piles and other objects. The input to the TIRe model is the georeferenced but otherwise raw satellite spectral images of a geographic region to be surveyed

Mobility needs of future customers and their impact on the drive train; Mobilitaetsbeduerfnisse der kommenden Kundengeneration und Auswirkungen auf den Antriebsstrang

Energy Technology Data Exchange (ETDEWEB)

Eckstein, Lutz; Ernst, Christian-Simon; Fassbender, Sven; Gnoerich, Bruno [RWTH Aachen (Germany). Inst. fuer Kraftfahrzeuge

2012-11-01

This contribution summarises on the basis of recent studies customer requirements regarding future vehicles concepts and their drivetrain designs and also shows several development directions for alternative drivetrains. The discussion of the megatrends emission reduction, urbanisation and peak-oil, influences the future demand of mobility. The megatrends implicate an enlargement of the possible solution space for full vehicle concepts. Two studies coordinated by the ''Institut fuer Kraftfahrzeuge (ika)'' of RWTH Aachen University show in detail the changed general conditions of mobility needs of the next customer generation. Besides their general attitude towards the automobile, especially their demands towards the drivetrain in technical and economic regard are analysed. The focus of this analysis lies in the possibilities to electrify the drivetrain, with a differentiation for different markets. Based on fundamental descriptions of essential characteristics of different drivetrain concepts, the development demands of alternative drive mechanisms are shown and variable solutions will be connected to the customer requirements in a costs analysis. The for the total cost analysis important aspect of energy consumption of alternatively driven vehicles will then be described with concrete examples of two different research- and benchmarking-projects. An evaluation of drivetrain concepts with possible fields of application will conclude the contribution with regard to technical and economic criteria. (orig.)

Survivability Enhanced Run-Flat Variable Footprint Tires

Science.gov (United States)

2010-08-17

with tire tread . By varying the thickness and geometry of the polyurethane soft layer, this unique tire -wheel assembly can generate a wide array of...carcass severely damaged/punctured, provide the same dynamic deflection as the normal pneumatic tire , and provide similar tread life. Could a tire be...be for an optimized shape. Fig 8 shows the actual process applied to a current tire . The carbon fiber was added by removing the tread , cutting

Research on Dynamic Optimization for Road-friendly Vehicle Suspension

Directory of Open Access Journals (Sweden)

Lu Yongjie

2014-10-01

Full Text Available The heavy vehicle brings large dynamic loads to the road surface, which would reduce vehicle ride comfort and shorten road service life. The structure characteristic of heavy vehicle suspension has a significant impact on vehicle performance. Based on the D'Alembert principle, the dynamics models of independent and integral balanced suspension are proposed considering mass and inertia of balancing rod. The sprung mass acceleration and the tire dynamic force for two kinds of balanced suspension and the traditional quarter vehicle model are compared in frequency-domain and time-domain respectively. It is concluded that a quarter vehicle model simplified for balanced suspension could be used to evaluate the ride comfort of vehicle well, but it has some limitations in assessing the vehicle road-friendliness. Then, the sprung mass acceleration and the road damage coefficients are also analyzed under different vehicle design and running parameters at detail. Some conclusions are obtained: low suspension stiffness, high suspension damping and low tire stiffness are all favorable to improve vehicle performance; there is a saturation range of suspension damping enhancing vehicle performance; improving the road surface roughness and avoiding the no-load running are two effective methods to accomplish the better ride comfort and road-friendliness. The suspension stiffness and damping parameters are chosen for optimal parameters matching of road friendliness based on the approximation optimization method.

Model-based state estimator for an intelligent tire

NARCIS (Netherlands)

Goos, J.; Teerhuis, A. P.; Schmeitz, A. J.C.; Besselink, I.; Nijmeijer, H.

2017-01-01

In this work a Tire State Estimator (TSE) is developed and validated using data from a tri-axial accelerometer, installed at the inner liner of the tire. The Flexible Ring Tire (FRT) model is proposed to calculate the tire deformation. For a rolling tire, this deformation is transformed into

Model-based State Estimator for an Intelligent Tire

NARCIS (Netherlands)

Goos, J.; Teerhuis, A.P.; Schmeitz, A.J.C.; Besselink, I.J.M.; Nijmeijer, H.

2016-01-01

In this work a Tire State Estimator (TSE) is developed and validated using data from a tri-axial accelerometer, installed at the inner liner of the tire. The Flexible Ring Tire (FRT) model is proposed to calculate the tire deformation. For a rolling tire, this deformation is transformed into

Aircraft and ground vehicle friction measurements obtained under winter runway conditions

Science.gov (United States)

Yager, Thomas J.

1989-01-01

Tests with specially instrumented NASA B-737 and B-727 aircraft together with several different ground friction measuring devices have been conducted for a variety of runway surface types and wetness conditions. This effort is part of the Joint FAA/NASA Aircraft/Ground Vehicle Runway Friction Program aimed at obtaining a better understanding of aircraft ground handling performance under adverse weather conditions, and defining relationships between aircraft and ground vehicle tire friction measurements. Aircraft braking performance on dry, wet, snow-, and ice-covered runway conditions is discussed together with ground vehicle friction data obtained under similar runway conditions. For the wet, compacted snow- and ice-covered runway conditions, the relationship between ground vehicles and aircraft friction data is identified. The influence of major test parameters on friction measurements such as speed, test tire characteristics, and surface contaminant-type are discussed. The test results indicate that use of properly maintained and calibrated ground vehicles for monitoring runway friction conditions should be encouraged particularly under adverse weather conditions.

Causes for torque degradation during deceleration and the effect on the driving range of battery electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Lieb, Johannes [BMW PEUGEOT CITROEN ELECTRIFICATION, Muenchen (Germany); Wilde, Andreas [BMW Group, Muenchen (Germany); Baeker, Bernard [Dresden Univ. of Technology (Germany). Dept. of Vehicle Mechatronics

2012-11-01

The ability to regain considerable amounts of the kinetic energy during deceleration phases is a key aspect to increase the efficiency of battery electric vehicles (BEV). Especially in urban and highly congested areas brake energy recovery (BER) can drastically improve the vehicle's driving range. However, due to the high power peaks that go along even with moderate braking maneuvers, severe requirements are being put on the electric drivetrain. Any limitation of power in one of the components of the powertrain inevitably leads to degradation of the regenerative brake torque, thus limiting the car's energy regeneration capability. Without an integrated brake system that can compensate the torque variations during deceleration, BER may need to be decreased even further to prevent a loss of driving comfort due to dynamic changes in the vehicle's behavior. This paper deals with the causes of these torque restraints within the electric drivetrain and how they affect the energy consumption and therefore the electric driving range. A simulation environment was set up and verified based on an existing BEV to conduct parameter studies and depict the sensitivities towards environmental influences. The calculated efficiencies are based on standard drive cycles and incorporate continuous fading between regenerative braking and the use of friction brakes. Special attention was laid on the battery system since energy storage still poses a particular challenge in the development of electric vehicles. Also through the high mutual dependence of the various parameters of the battery enviromental influences become most evident. (orig.)

78 FR 21191 - NHTSA Activities Under the United Nations World Forum for the Harmonization of Vehicle...

Science.gov (United States)

2013-04-09

... hybrid-electric vehicles that can run exclusively on an electric motor, electric vehicles and fuel-cell... 3. Quiet Electric and Hybrid-Electric Vehicles 4. Electric Vehicles 5. Light Vehicle Tires B. Status... Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on...

49 CFR 398.4 - Driving of motor vehicles.

Science.gov (United States)

2010-10-01

.... Lighting devices and reflectors. Tires. Horn. Windshield wiper or wipers. Rear-vision mirror or mirrors.... No driver or any employee of a motor carrier shall: (1) Fuel a motor vehicle with the engine running, except when it is necessary to run the engine to fuel the vehicle; (2) Smoke or expose any open flame in...

Airplane tire inspection by image processing techniques

OpenAIRE

Jovancevic , Igor; Arafat , Al; Orteu , Jean-José; Sentenac , Thierry

2016-01-01

International audience; In this paper, we propose a new approach to detect and inspect airplane tires. We use normalized correlation based template matching to detect tires and GrabCut segmentation method to extract them from the background. We inspect the tires condition by investigating the tire treads. Ridge based intensity profiling gives satisfying inspection results.

Studless Winter Tires

Science.gov (United States)

1976-01-01

Goodyear Tire and Rubber Company developed a material for Johnson Space Center used as parachute shrouds to soft land the Vikings through the tenuous Martian atmosphere and has been adapted to new radial tire five times stronger than steel. Fiber has a chain-like molecular structure that gives it incredible strength in proportion to its weight. Material is expected to increase tread life by 10,000 miles.

System Interface for an Integrated Intelligent Safety System (ISS for Vehicle Applications

Directory of Open Access Journals (Sweden)

Mahammad A. Hannan

2010-01-01

Full Text Available This paper deals with the interface-relevant activity of a vehicle integrated intelligent safety system (ISS that includes an airbag deployment decision system (ADDS and a tire pressure monitoring system (TPMS. A program is developed in LabWindows/CVI, using C for prototype implementation. The prototype is primarily concerned with the interconnection between hardware objects such as a load cell, web camera, accelerometer, TPM tire module and receiver module, DAQ card, CPU card and a touch screen. Several safety subsystems, including image processing, weight sensing and crash detection systems, are integrated, and their outputs are combined to yield intelligent decisions regarding airbag deployment. The integrated safety system also monitors tire pressure and temperature. Testing and experimentation with this ISS suggests that the system is unique, robust, intelligent, and appropriate for in-vehicle applications.

49 CFR 230.113 - Wheels and tire defects.

Science.gov (United States)

2010-10-01

... tires may not have a seam running lengthwise that is within 33/4 inches of the flange. (g) Worn flanges... 49 Transportation 4 2010-10-01 2010-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

Tire-road noise: an experimental study of tire and road design parameters

NARCIS (Netherlands)

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire

Numerical prediction of car tire wear

NARCIS (Netherlands)

Lupker, H.A.; Cheli, F.; Braghin, F.; Gelosa, E.; Keckman, A.

2004-01-01

Due to their many economic and ecological implications, the possibility to predict tire wear is of major importance to tire manufacturers, fleet owners and governments. Based on these observations, in 2000, a three-year project named TROWS (Tire and Road Wear and Slip assessment was started. One of

Modular Estimation Strategy of Vehicle Dynamic Parameters for Motion Control Applications

Directory of Open Access Journals (Sweden)

Rawash Mustafa

2018-01-01

Full Text Available The presence of motion control or active safety systems in vehicles have become increasingly important for improving vehicle performance and handling and negotiating dangerous driving situations. The performance of such systems would be improved if combined with knowledge of vehicle dynamic parameters. Since some of these parameters are difficult to measure, due to technical or economic reasons, estimation of those parameters might be the only practical alternative. In this paper, an estimation strategy of important vehicle dynamic parameters, pertaining to motion control applications, is presented. The estimation strategy is of a modular structure such that each module is concerned with estimating a single vehicle parameter. Parameters estimated include: longitudinal, lateral, and vertical tire forces – longitudinal velocity – vehicle mass. The advantage of this strategy is its independence of tire parameters or wear, road surface condition, and vehicle mass variation. Also, because of its modular structure, each module could be later updated or exchanged for a more effective one. Results from simulations on a 14-DOF vehicle model are provided here to validate the strategy and show its robustness and accuracy.

Exterior Noise Due to Interaction of Tire-Thermoplastic Transverse Rumble Strips

Directory of Open Access Journals (Sweden)

Haron Zaiton

2017-01-01

Full Text Available Transverse rumble strips (TRS are a common choice to reduce vehicle speed and increase driver alertness on roadways. However, there is a potential trade-off using them on rural roadway due to the noise problem created when vehicles go over the strips. The present study investigated the noise level, spectral analysis and the possible noise generation mechanism when the TRS hit by a vehicle. Ten-raised-rumbler (RR and three-layer-overlapped (TLO were selected in this study as they have received complaints from the public. Results showed that RR generated relatively higher noise and impulse at low speed, and increased sound level in each octave band. Based on these results, RR may irritate human ears even when the vehicle travels at low speed. It was found that RR increased all noise generation mechanism of tire-pavement interaction whilst for the TLO increased structural resonance, sidewall and surface texture vibration.

Off-road vehicle dynamics analysis, modelling and optimization

CERN Document Server

Taghavifar, Hamid

2017-01-01

This book deals with the analysis of off-road vehicle dynamics from kinetics and kinematics perspectives and the performance of vehicle traversing over rough and irregular terrain. The authors consider the wheel performance, soil-tire interactions and their interface, tractive performance of the vehicle, ride comfort, stability over maneuvering, transient and steady state conditions of the vehicle traversing, modeling the aforementioned aspects and optimization from energetic and vehicle mobility perspectives. This book brings novel figures for the transient dynamics and original wheel terrain dynamics at on-the-go condition.

Directions for material recovery of used tires and their use in the production of new products intended for the industry of civil construction and pavements

Science.gov (United States)

Bulei, C.; Todor, M. P.; Heput, T.; Kiss, I.

2018-01-01

The management of waste from used tires is one of the major principles of recycling and reuse, which involves encouraging a high level of material recovery components, preferably by recycling. Given the current pressure on natural resources on a global scale we must fully take into account the waste in a broader framework defined by the flow of raw materials and their sustainable use. Thus, the opportunity to use various waste from used tires as raw material in order to support economic activities becomes a priority. The recycling of raw materials from waste products and their use in new production processes for their material capitalization is becoming a sustainable approach. Used tire recycling, is the process of recycling waste tires that are no longer suitable for use on vehicles due to wear or irreparable damage. These tires are a problematic source of waste, due to the large volume produced, the durability of the tires, and the components in the tire that are ecologically problematic. Although tires are usually burnt, not recycled, efforts are continuing to find value. Tires can be recycled into, among other things, typically as crumb rubber modifier in recycled pavement. The paper presents aspects of the product resulting from crushing of used tires (powder), which can be used properly valued in the street furniture field or building materials containing rubber.

TIRE MODELS USED IN VEHICLE DYNAMIC APPLICATIONS AND THEIR USING IN VEHICLE ACCIDENT SIMULATIONS

Directory of Open Access Journals (Sweden)

Osman ELDOĞAN

1995-01-01

Full Text Available Wheel model is very important in vehicle modelling, it is because the contact between vehicle and road is achieved by wheel. Vehicle models can be dynamic models which are used in vehicle design, they can also be models used in accident simulations. Because of the importance of subject, many studies including theoretical, experimental and mixed type have been carried out. In this study, information is given about development of wheel modelling and research studies and also use of these modellings in traffic accident simulations.

Piecewise affine control for fast unmanned ground vehicles

OpenAIRE

Benine Neto , André; Grand , Christophe

2012-01-01

International audience; Unmanned ground vehicles (UGV) may experience skidding when moving at high speeds, and therefore have its safety jeopardized. For this reason the nonlinear dynamics of lateral tire forces must be taken into account into the design of steering controllers for autonomous vehicles. This paper presents the design of a state feedback piecewise affine controller applied to an UGV to coordinate the steering and torque distribution inputs in order to reduce vehicle skidding on...

77 FR 3031 - The Goodyear Tire & Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-01-20

... July 2010. A total of approximately 38,991 of these tires have been delivered to Goodyear's customers... is inconsequential to motor vehicle safety, and that its petition, to exempt from providing recall notification of noncompliance as required by 49 U.S.C. 30118 and remedying the recall noncompliance as required...

76 FR 55859 - Federal Motor Vehicle Safety Standards No. 121; Air Brake Systems

Science.gov (United States)

2011-09-09

... during road tests for the braking system, a vehicle equipped with an interlocking axle system or a front... vehicle braking systems, tire characteristics related to lateral force and longitudinal force generation... stopping distance without activating the ABS system by braking the vehicle so that the brake pressure is...

Energy requirements of tire pulling.

Science.gov (United States)

Fredriksen, Per M; Mamen, Asgeir

2017-10-01

We have investigated the effect using walking poles and pulling tires at 4 and 6 km·h-1 (1.11 and 1.67 m·s-1) speeds on oxygen uptake (V̇O2) and heart rate. Eleven subjects, 6 males, with a mean (SD) age of 25.2 (6.9) years participated in field tests involving walking without poles, walking with poles and tire pulling with poles. Increasing the load caused the largest increases in energy demand, more than 4 MET. Speed increase also caused substantial energy increase, approximately 4 MET. Increasing the inclination only modestly increased the oxygen uptake, approximately 2 MET. In both level walking and uphill walking, using poles marginally increased oxygen uptake compared to working without poles. Pulling one tire (12.5 kg) required an oxygen uptake of 27 (4) mL·kg-1·min-1 at 4 km·h-1 and 0% inclination. Adding one more tire (6 kg) drove the oxygen uptake further up to 39 (4) mL·kg-1·min-1. This is close to the requirement of level running at 10.5 km·h-1. Pulling both tires at 6 km·h-1 and 5% inclination required a V̇O2 of 54 (6) mL·kg-1·min-1, equal to running uphill at 5% inclination and 12.5 km·h-1 speed. Heart rate rose comparably with oxygen uptake. At 4 km·h-1 and 0% inclination the increase was 29 bpm, from 134 (21) to 163 (22) bpm when going from pulling one tire to two tires. In the hardest exercise, 6 km·h-1 and 5% inclination, heart rate reached 174 (14) bpm. The study showed that tire pulling even at slow speeds has an energy requirement that is so large that the activity may be feasible as endurance training.

Environmental impact caused by incorrect discard of tires

Directory of Open Access Journals (Sweden)

Vitória Emanuella da Silva Alves

2015-11-01

Full Text Available Tires are wastes that need special treatment, because when buried whole, its shape facilitates the accumulation of gases from the decomposition of other waste and in case of emerge surface provides shelter for diseases. Thus, this research aimed to provide information about the environmental impacts caused by the improper disposal of unserviceable tires and about some techniques for reusing and recycling them. We opted for the literature search using databases SCIELO, GOOGLE SCHOLAR, CAPES journals, resolutions of the MMA, the ANIP and regulations of IBAMA instructions. The consultation material comprises a period from 1992 to 2015 with the following descriptors: industrial waste; laws of tires; environmental impacts caused by improper disposal of tires and technological alternatives usable by tires and scrap therefore improper disposal of scrap tires can cause negative impacts such as floods, by reducing the flow capacity of water bodies and drains. In contrast, after use, the tire can undergo reform and be reused, but the wear out is completely characterized as waste tire and the correct disposal are the possible ways of recycling. Thus it is very important compliance of laws that deal with the proper disposal of tires.

Contribution to the analysis of the influence of parameters of elasto-damping elements to the vehicle ride comfort

Directory of Open Access Journals (Sweden)

Demić Miroslav D.

2017-01-01

Full Text Available During development of motor vehicles, a significant role has a dynamic simulation, which is based on the modeling. Role modeling is very important in the early stages of design, during definition of the vehicles main parameters. Literature sources provide complete responses to the influence of the forces in springs, shock absorbers and tires on the vehicle oscillatory comfort, but hardly anyone engaged in analysis of parameters of the models of elasto-damping elements on the oscillations of the vehicle. This paper will attempt to be made, on the basis of the adopted models of springs, shock absorbers and tires, perform analysis of the influence of parameters on the oscillations of the vehicle. For that purpose they used so-called sensitivity functions.

Simulation model of an electrohydraulic-actuated double-clutch transmission vehicle: modelling and system design

Science.gov (United States)

Schoeftner, J.; Ebner, W.

2017-12-01

Automated and manual transmissions are the main link between engine and powertrain. The technical term when the transmission provides the desired torque during all possible driving conditions is denoted as powertrain matching. Recent developments in the last years show that double-clutch-transmissions (DCTs) are a reasonable compromise in terms of production costs, shifting quality, drivability and fuel efficiency. They have several advantages compared to other automatic transmissions (AT). Most DCTs nowadays consist of a hydraulic actuation control unit, which controls the clutches of the gearbox in order to induce a desired drivetrain torque into the driveline. The main functions of hydraulic systems are manifold: they initiate gear shifts, they provide sufficient oil for lubrication and they control the shift quality by suitably providing a desired oil flow or pressure for the clutch actuation. In this paper, a mathematical model of a passenger car equipped with a DCT is presented. The objective of this contribution is to get an increased understanding for the dynamics of the hydraulic circuit and its coupling to the vehicle drivetrain. The simulation model consists of a hydraulic and a mechanical domain: the hydraulic actuation circuit is described by nonlinear differential equations and includes the dynamics of the line pressure and the proportional valve, as well as the influence of the pressure reducing valve, pipe resistances and accumulator dynamics. The drivetrain with its gear ratios, moments of inertia, torsional stiffness of the rotating shafts and a simple longitudinal vehicle model represent the mechanical domain. The link between hydraulic and mechanical domain is given by the clutch, which combines hydraulic equations and Newton's laws. The presented mathematical model may not only be used as a simulation model for developing the transmission control software, it may also serve as a virtual layout for the design process phase. At the end of this

Nonlinear Analysis and Modeling of Tires

Science.gov (United States)

Noor, Ahmed K.

1996-01-01

The objective of the study was to develop efficient modeling techniques and computational strategies for: (1) predicting the nonlinear response of tires subjected to inflation pressure, mechanical and thermal loads; (2) determining the footprint region, and analyzing the tire pavement contact problem, including the effect of friction; and (3) determining the sensitivity of the tire response (displacements, stresses, strain energy, contact pressures and contact area) to variations in the different material and geometric parameters. Two computational strategies were developed. In the first strategy the tire was modeled by using either a two-dimensional shear flexible mixed shell finite elements or a quasi-three-dimensional solid model. The contact conditions were incorporated into the formulation by using a perturbed Lagrangian approach. A number of model reduction techniques were applied to substantially reduce the number of degrees of freedom used in describing the response outside the contact region. The second strategy exploited the axial symmetry of the undeformed tire, and uses cylindrical coordinates in the development of three-dimensional elements for modeling each of the different parts of the tire cross section. Model reduction techniques are also used with this strategy.

Fuel Economy and Emissions Effects of Low Tire Pressure, Open Windows, Roof Top and Hitch-Mounted Cargo, and Trailer

Energy Technology Data Exchange (ETDEWEB)

Thomas, John F [ORNL; Huff, Shean P [ORNL; West, Brian H [ORNL

2014-01-01

To quantify the fuel economy (FE) effect of some common vehicle accessories or alterations, a compact passenger sedan and a sport utility vehicle (SUV) were subjected to SAE J2263 coastdown procedures. Coastdowns were conducted with low tire pressure, all windows open, with a roof top or hitch-mounted cargo carrier, and with the SUV pulling an enclosed cargo trailer. From these coastdowns, vehicle dynamometer coefficients were developed which enabled the execution of vehicle dynamometer experiments to determine the effect of these changes on vehicle FE and emissions over standard drive cycles and at steady highway speeds. The FE penalty associated with the rooftop cargo box mounted on the compact sedan was as high as 25-27% at higher speeds, where the aerodynamic drag is most pronounced. For both vehicles, use of a hitch mounted cargo tray carrying a similar load resulted in very small FE penalties, unlike the rooftop cargo box. The results for the SUV pulling a 3500 pound enclosed cargo trailer were rather dramatic, resulting in FE penalties ranging from 30%, for the city cycle, to 50% at 80 mph, at which point significant CO generation indicated protective enrichment due to high load. Low tire pressure cases resulted in negligible to 10% FE penalty depending on the specific case and test point. Driving with all four windows open decreased FE by 4-8.5% for the compact sedan, and 1-4% for the SUV.

Usage of post-consumer tires as raw materials

Directory of Open Access Journals (Sweden)

O.A. Vovk

2006-04-01

Full Text Available  This article is devoted to the problem of post-consumer tires accumulation and recycling both in Europe and Ukraine. It describes general tires properties, their structure and composite elements which are valuable secondary resources. Also there are analyzed the most known methods of used tires treatment and final product of tires utilizations.

Automobile Tire Assessment: A Multi-Criteria Approach

Directory of Open Access Journals (Sweden)

Ateekh-Ur-Rehman

2017-02-01

Full Text Available In response to the present dynamic market, automobile manufacturing industries are constantly evaluating and improving their manufacturing strategies to stay competitive. It is also evident that they evaluate those strategies considering multiple criteria. In one such case, an automobile project manager has to ensure that the selected tire (among the available alternatives complies with the prospective automobile’s performance. This paper presents an approach for the assessment of alternative automobile tires taking into account multiple criteria, such as tire sustainability, tire road performance, environmental issues, tire purchase cost and tire road grip. The presented approach is quite helpful to any decision maker who is interested not only in ranking alternatives but also in establishing the superiority of an alternative over others. The approach also helps to specify the position of each alternative with respect to ideal solution. A case illustration is used to demonstrate an application of the approach.

State-of-the-Art Review on Sustainable Design and Construction of Quieter Pavements—Part 2: Factors Affecting Tire-Pavement Noise and Prediction Models

Directory of Open Access Journals (Sweden)

Okan Sirin

2016-07-01

Full Text Available Traffic noise is a combination of noises produced from a number of sources. Of all the traffic noise sources, tire-pavement noise, which is emitted as a result of the interaction of rolling, slipping, or dragging tires and the pavement surface, is the dominant contributor of overall noise, particularly when vehicles are moving at higher speeds. Therefore, a number of research studies have been conducted to identify and analyze the factors affecting the generation of tire-pavement interaction noise. This helps in identifying and selecting appropriate noise mitigation techniques. In this paper, an extensive literature survey on the factors affecting tire-pavement noise is presented, and different views on the impact of each individual factor are discussed. From the literature survey, it is also evident that there is a potential correlation between pavement’s material characteristics and tire-pavement noise. A comprehensive discussion about this correlation is presented in the paper. In addition, this paper discusses various mathematical models for predicting pavement noise, and their advantages and shortcomings.

Use of shredded tire chips and tire crumbs as packing media in trickling filter systems for landfill leachate treatment.

Science.gov (United States)

Mondal, B; Warith, M A

2008-08-01

Scrap tire stockpiles are breeding grounds for pests, mosquitoes and west Nile viruses and, thereby, become a potential health risk. This experimental study was carried out in six stages to determine the suitability of shredded tire materials in a trickling filter system to treat landfill leachate. Biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and NH3-N removals were obtained in the range of 81 to 96%, 76 to 90% and 15 to 68%, respectively. The removal of organics appears to be largely related to total dissolved solids reduction in leachate. A sudden increase, from time to time, in organic content of effluent could be attributed to biomass sloughing and clogging in the trickling filters. However, tire crumbs exhibited more consistent organics removal throughout the experimental program. Due to the high surface area of shredded tire chips and crumbs, a layer of biomass, 1-2 mm thick, was attached to them and was sloughed off at an interval of 21 days. Apart from that, as shredded tires are comparatively cheaper than any other usable packing material, tire chips and tire crumbs appeared to be quite promising as packing media in trickling filters for landfill leachate treatment.

Characterizing Tire Crumb Rubber for Exposure Assessment

Science.gov (United States)

Tire crumb rubber derived from recycled tires is widely used as infill material in synthetic turf fields in the United States. An estimated 95% of the over 12,000 installed fields in the U.S. use tire crumb rubber infill alone or mixed with sand or alternative materials. Concerns...

NASA tire/runway friction projects

Science.gov (United States)

Yager, Thomas J.

1995-01-01

The paper reviews several aspects of NASA Langley Research Center's tire/runway friction evaluations directed towards improving the safety and economy of aircraft ground operations. The facilities and test equipment used in implementing different aircraft tire friction studies and other related aircraft ground performance investigations are described together with recent workshop activities at NASA Wallops Flight Facility. An overview of the pending Joint NASA/Transport Canada/FM Winter Runway Friction Program is given. Other NASA ongoing studies and on-site field tests are discussed including tire wear performance and new surface treatments. The paper concludes with a description of future research plans.

Method of sections in analytical calculations of pneumatic tires

Science.gov (United States)

Tarasov, V. N.; Boyarkina, I. V.

2018-01-01

Analytical calculations in the pneumatic tire theory are more preferable in comparison with experimental methods. The method of section of a pneumatic tire shell allows to obtain equations of intensities of internal forces in carcass elements and bead rings. Analytical dependencies of intensity of distributed forces have been obtained in tire equator points, on side walls (poles) and pneumatic tire bead rings. Along with planes in the capacity of secant surfaces cylindrical surfaces are used for the first time together with secant planes. The tire capacity equation has been obtained using the method of section, by means of which a contact body is cut off from the tire carcass along the contact perimeter by the surface which is normal to the bearing surface. It has been established that the Laplace equation for the solution of tasks of this class of pneumatic tires contains two unknown values that requires the generation of additional equations. The developed computational schemes of pneumatic tire sections and new equations allow to accelerate the pneumatic tire structure improvement process during engineering.

Development and Verification of the Tire/Road Friction Estimation Algorithm for Antilock Braking System

Directory of Open Access Journals (Sweden)

Jian Zhao

2014-01-01

Full Text Available Road friction information is very important for vehicle active braking control systems such as ABS, ASR, or ESP. It is not easy to estimate the tire/road friction forces and coefficient accurately because of the nonlinear system, parameters uncertainties, and signal noises. In this paper, a robust and effective tire/road friction estimation algorithm for ABS is proposed, and its performance is further discussed by simulation and experiment. The tire forces were observed by the discrete Kalman filter, and the road friction coefficient was estimated by the recursive least square method consequently. Then, the proposed algorithm was analysed and verified by simulation and road test. A sliding mode based ABS with smooth wheel slip ratio control and a threshold based ABS by pulse pressure control with significant fluctuations were used for the simulation. Finally, road tests were carried out in both winter and summer by the car equipped with the same threshold based ABS, and the algorithm was evaluated on different road surfaces. The results show that the proposed algorithm can identify the variation of road conditions with considerable accuracy and response speed.

State-of-the-art assessment of electric and hybrid vehicles

Science.gov (United States)

1978-01-01

Data are presented that were obtained from the electric and hybrid vehicles tested, information collected from users of electric vehicles, and data and information on electric and hybrid vehicles obtained on a worldwide basis from manufacturers and available literature. The data given include: (1) information and data base (electric and hybrid vehicle systems descriptions, sources of vehicle data and information, and sources of component data); (2) electric vehicles (theoretical background, electric vehicle track tests, user experience, literature data, and summary of electric vehicle status); (3) electric vehicle components (tires, differentials, transmissions, traction motors, controllers, batteries, battery chargers, and component summary); and (4) hybrid vehicles (types of hybrid vehicles, operating modes, hybrid vehicles components, and hybrid vehicles performance characteristics).

Forestry Tire Tractive Performance: New, Worn, and with Chains

Science.gov (United States)

C.R. Vechinski; C.R. Johnson; R.L. Raper; T.P. McDonald

1999-01-01

The tractive perfomance of a new tire, a worn tire, and a worn tire with forestry tire chains was measured in four soil types. Two of the soil types simulated forest-floor conditions with one soil type having a sulfate cover of pine straw and the other having a surface cover of sod. The two remaining soil types were bare. The worn tire with and without chains had...

Vehicle dynamics theory and application

CERN Document Server

Jazar, Reza N

2017-01-01

This intermediate textbook is appropriate for students in vehicle dynamics courses, in their last year of undergraduate study or their first year of graduate study. It is also appropriate for mechanical engineers, automotive engineers, and researchers in the area of vehicle dynamics for continuing education or as a reference. It addresses fundamental and advanced topics, and a basic knowledge of kinematics and dynamics, as well as numerical methods, is expected. The contents are kept at a theoretical-practical level, with a strong emphasis on application. This third edition has been reduced by 25%, to allow for coverage over one semester, as opposed to the previous edition that needed two semesters for coverage. The textbook is composed of four parts: Vehicle Motion: covers tire dynamics, forward vehicle dynamics, and driveline dynamics Vehicle Kinematics: covers applied kinematics, applied mechanisms, steering dynamics, and suspension mechanisms Vehicle Dynamics: covers applied dynamics, vehicle planar dynam...

41 CFR 101-25.110 - Tire identification/registration program.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Tire identification...-General Policies § 101-25.110 Tire identification/registration program. The regulations issued by the Department of Transportation in 49 CFR part 574, Tire Identification and Recordkeeping, require that tire...

49 CFR 230.112 - Wheels and tires.

Science.gov (United States)

2010-10-01

... wheels mounted on the same axle shall not vary more than 1/4 inch. (d) Tire thickness. Wheels may not have tires with a minimum thickness less than that indicated in the table in this paragraph (d). When... the minimum thickness of tires may be as much below the limits specified earlier in this paragraph (d...

Geotechnical Properties of Rubber Tires and Sediments Mixtures

Directory of Open Access Journals (Sweden)

H. Sellaf

2014-04-01

Full Text Available An experimental work was undertaken to study the effect of rubber tires on the geotechnical properties of a dredged sediment, using a mixing ratio of large size. For comparison, two types of soil were studied (dredged sediment from Fergoug dam and Tizi Tuff from the north west of Algeria. Taking into account the high compressibility and the low water absorption of the rubber tires, grain size analysis, density, Atterberg limits analysis, chemical composition, direct shear tests, loading-unloading tests, modified Proctor and CBR tests are performed on the two soils and their mixtures with different scrap tire rubber (10, 20, 25 and 50%. The results show that liquid limits and plastic indexes decrease with the scrap tire rubber content and that the decrease is more significant for soil with high plasticity. Cohesion also decreases with scrap tire rubber content when the internal friction angle is vacillating. Compression and recompression indexes increase gradually with the scrap tire rubber content and the variation for compression index is more significant for the two soils. Compaction characteristics and CBR values decrease with scrap tire rubber content. The CBR values for W=3% are important compared to those with W=5% excepted for mixture with (75% tuff and 25% scrap tire rubber. The results show that the scrap tire rubber can be used as a reinforcement material for dredged soil, but with a content that should not highly affect the compressibility.

Recovery and disposal of discarded tires in the Taiwan area.

Science.gov (United States)

Hwang, J S; Roam, G D

1994-12-01

Urbanization and industrialization has resulted in a vast amount of artificial water containers in Taiwan, especially discarded automobile tires. 3.5 million automobile tires and several million motorcycle tires are discarded annually. The discarded tires contaminate the environment and also become a substantial number of breeding sites for the dengue vector mosquitoes. In order to establish a sound system for the recovery and disposal of discarded tires and to control dengue fever through source reduction, it has been emphasized that users must pay for their waste. It is necessary to recover and properly dispose of these discarded tired. The commercial firms which sell or manufacture tires are therefore advised to cooperate with the Environmental Protection Administration of the Executive Yuan, R.O.C. and follow the "Regulations of Recovery and Disposal of Discarded Tires". They are requested to establish foundations for the recovery of discarded tires. Those who are willing to join should prepay a deposit or related charge by the size of tire, which is imported or locally manufactured. The foundation utilizes the deposits for the recovery and disposal of discarded tires. From 1991 to 1993 the commercial tire firms had already achieved the 80% recovery rates declared by the authorities concerned. Some of the tires, after having been recovered, were recycled in the original form and the rest were cut into small pieces for recycling after physical treatment. It should be mentioned that the Department of Environmental Protection of Kaohsiung City has collected 80 thousand discarded automobile tires to be used as ocean jetty.(ABSTRACT TRUNCATED AT 250 WORDS)

Dynamics and Stability of Rolling Viscoelastic Tires

Energy Technology Data Exchange (ETDEWEB)

Potter, Trevor [Univ. of California, Berkeley, CA (United States)

2013-04-30

Current steady state rolling tire calculations often do not include treads because treads destroy the rotational symmetry of the tire. We describe two methodologies to compute time periodic solutions of a two-dimensional viscoelastic tire with treads: solving a minimization problem and solving a system of equations. We also expand on work by Oden and Lin on free spinning rolling elastic tires in which they disovered a hierachy of N-peak steady state standing wave solutions. In addition to discovering a two-dimensional hierarchy of standing wave solutions that includes their N-peak hiearchy, we consider the eects of viscoelasticity on the standing wave solutions. Finally, a commonplace model of viscoelasticity used in our numerical experiments led to non-physical elastic energy growth for large tire speeds. We show that a viscoelastic model of Govindjee and Reese remedies the problem.

Co-gasification of tire and biomass for enhancement of tire-char reactivity in CO2 gasification process.

Science.gov (United States)

Lahijani, Pooya; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman; Mohammadi, Maedeh

2013-06-01

In this investigation, palm empty fruit bunch (EFB) and almond shell (AS) were implemented as two natural catalysts rich in alkali metals, especially potassium, to enhance the reactivity of tire-char through co-gasification process. Co-gasification experiments were conducted at several blending ratios using isothermal Thermogravimetric analysis (TGA) under CO2. The pronounced effect of inherent alkali content of biomass-chars on promoting the reactivity of tire-char was proven when acid-treated biomass-chars did not exert any catalytic effect on improving the reactivity of tire-char in co-gasification experiments. In kinetic studies of the co-gasified samples in chemically-controlled regime, modified random pore model (M-RPM) was adopted to describe the reactive behavior of the tire-char/biomass-char blends. By virtue of the catalytic effect of biomass, the activation energy for tire-char gasification was lowered from 250 kJ/mol in pure form 203 to 187 kJ/mol for AS-char and EFB-char co-gasified samples, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Continuous monitoring the vehicle dynamics and driver behavior using navigation systems

Science.gov (United States)

Ene, George

2017-10-01

In all fields cost is very important and the increasing amount of data that are needed for active safety systems, like ADAS, lead to implementation of some complex and powerful unit for processing raw data. In this manner is necessary a cost-effective method to estimate the maximum available tire road friction during acceleration and braking by continuous monitoring the vehicle dynamics and driver behavior. The method is based on the hypothesis that short acceleration and braking periods can indicate vehicle dynamics, and thus the available tire road friction coefficient, and also human behavior and his limits. Support for this hypothesis is found in the literature and is supported by the result of experiments conducted under different conditions and seasons.

Experimental evaluation of optimal Vehicle Dynamic Control based on the State Dependent Riccati Equation technique

NARCIS (Netherlands)

Alirezaei, M.; Kanarachos, S.A.; Scheepers, B.T.M.; Maurice, J.P.

2013-01-01

Development and experimentally evaluation of an optimal Vehicle Dynamic Control (VDC) strategy based on the State Dependent Riccati Equation (SDRE) control technique is presented. The proposed nonlinear controller is based on a nonlinear vehicle model with nonlinear tire characteristics. A novel

Caltrans use of scrap tires in asphalt rubber products: a comprehensive review

Directory of Open Access Journals (Sweden)

Haiping Zhou

2014-02-01

Full Text Available The California Department of Transportation (Caltrans has been using scrap tire rubber in asphalt pavements since the 1970s in chip seals and the 1980s in rubberized hot mix asphalt(RHMA. Both the wet (field blend and dry processes were used in early trials. Caltrans has also used rubber modified binders containing both crumb rubber modifier and polymer modifier that could be manufactured at a refinery facility, a terminal blend wet process. Since the beginning of this century, Caltrans increased the use of scrap tire rubber in paving projects and invested considerable resources in developing technically sound, cost effective, and environmentally friendly strategies for using scrap tire rubber in roadway applications. By the end of year 2010, approximately 31%of all hot mix asphalt (HMA placed by Caltrans was rubberized HMA, roughly 1.2 million tons. Caltrans efforts in using asphalt rubber products were also demonstrated in its research and technology development. These included the construction of two full-scale field experiments, five warranty projects, and an accelerated pavement study using a heavy vehicle simulator. Additionally, terminal blend asphalt rubber and rubberized warm mix asphalts began to be experimented on trial basis. This paper provides a comprehensive review of Caltrans experience over four decades with asphalt rubber products. Current practices and future outlook are also discussed.

AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

Science.gov (United States)

The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

Simulation of Thermal Signature of Tires and Tracks

Science.gov (United States)

2012-08-01

the body-ply is a linear elastic material. To facilitate the analysis, the tire was divided into Tread and Sidewall by the dash line as shown in...only one element is assigned through the thickness of the tire . Therefore, the thickness of the element is the same as the thickness of the tire ...to the whole part of the 3D full tire in the thermal analysis. The average strain energy density for each part ( tread or sidewall) in the cross

A procedure for multi-objective optimization of tire design parameters

OpenAIRE

Nikola Korunović; Miloš Madić; Miroslav Trajanović; Miroslav Radovanović

2015-01-01

The identification of optimal tire design parameters for satisfying different requirements, i.e. tire performance characteristics, plays an essential role in tire design. In order to improve tire performance characteristics, formulation and solving of multi-objective optimization problem must be performed. This paper presents a multi-objective optimization procedure for determination of optimal tire design parameters for simultaneous minimization of strain energy density at two distinctive zo...

Active and semi-active control of suspension systems for commercial vehicles based on preview

NARCIS (Netherlands)

Kok, J.J.; van Heck, J.G.A.M.; Muijderman, J.H.E.A.; Veldpaus, F.E.

1997-01-01

The performance of a vehicle axle/wheel suspension system is primarily determined by the comfort of the occupants, the required working space, the handling properties and, for commercial vehicles in particular, the dynamic tire forces and the load on the chassis components and on the cargo. General

The tires and their effect in fuel consumption; Los neumaticos y su efecto en el consumo de combustible

Energy Technology Data Exchange (ETDEWEB)

Barjau Peralta, Emilio; Fernandez Ramirez, Adrian; Maldonado Susano, Armando [Comision Nacional para el Ahorro de Energia, Mexico, D.F. (Mexico)

1999-07-01

In this paper are presented some of the impacts that the tire has in the fuel consumption in the light vehicles as well as in the heavy ones; emphasis is made in the measures that can be taken to diminish this effect and some of the results of the investigations or experiences obtained in other countries are also presented. Also mention is made of the most frequent faults of the tires and the cause of the same ones. This affects not so much the life of the tire as the operation cost, but also it involves energy costs when having to invest energy in the manufacture of new tires. [Spanish] En este trabajo se presentan algunas de los impactos que tienen el neumatico en el consumo de combustible en los vehiculos tanto ligeros como pesados, se hace enfasis en las medidas que pueden ser tomadas para disminuir este efecto y se muestran algunos resultados de las investigaciones o experiencias obtenidas en otros paises. Tambien se hace mencion de las fallas mas frecuentes en los neumaticos y la causa de las mismas. Esto afecta tanto la vida del neumatico como el costo de operacion, pero tambien involucra costos energeticos al tener que invertir energia en la fabricacion de neumaticos nuevos.

Design of a Path-Tracking Steering Controller for Autonomous Vehicles

Directory of Open Access Journals (Sweden)

Chuanyang Sun

2018-06-01

Full Text Available This paper presents a linearization method for the vehicle and tire models under the model predictive control (MPC scheme, and proposes a linear model-based MPC path-tracking steering controller for autonomous vehicles. The steering controller is designed to minimize lateral path-tracking deviation at high speeds. The vehicle model is linearized by a sequence of supposed steering angles, which are obtained by assuming the vehicle can reach the desired path at the end of the MPC prediction horizon and stay in a steady-state condition. The lateral force of the front tire is directly used as the control input of the model, and the rear tire’s lateral force is linearized by an equivalent cornering stiffness. The course-direction deviation, which is the angle between the velocity vector and the path heading, is chosen as a control reference state. The linearization model is validated through the simulation, and the results show high prediction accuracy even in regions of large steering angle. This steering controller is tested through simulations on the CarSim-Simulink platform (R2013b, MathWorks, Natick, MA, USA, showing the improved performance of the present controller at high speeds.

A procedure for multi-objective optimization of tire design parameters

Directory of Open Access Journals (Sweden)

Nikola Korunović

2015-04-01

Full Text Available The identification of optimal tire design parameters for satisfying different requirements, i.e. tire performance characteristics, plays an essential role in tire design. In order to improve tire performance characteristics, formulation and solving of multi-objective optimization problem must be performed. This paper presents a multi-objective optimization procedure for determination of optimal tire design parameters for simultaneous minimization of strain energy density at two distinctive zones inside the tire. It consists of four main stages: pre-analysis, design of experiment, mathematical modeling and multi-objective optimization. Advantage of the proposed procedure is reflected in the fact that multi-objective optimization is based on the Pareto concept, which enables design engineers to obtain a complete set of optimization solutions and choose a suitable tire design. Furthermore, modeling of the relationships between tire design parameters and objective functions based on multiple regression analysis minimizes computational and modeling effort. The adequacy of the proposed tire design multi-objective optimization procedure has been validated by performing experimental trials based on finite element method.

Optical strain measurement for fault detection in haul-truck tires

International Nuclear Information System (INIS)

Kotchon, A; Nobes, D S; Lipsett, M G

2012-01-01

Tire condition is integral to the safe operation of heavy machinery, such as ultra-class haul trucks. A new approach to haul truck tire monitoring is being investigated based on optical strain measurement, which has the advantage of providing quantitative information from sensors that do not contact the tire. A laboratory-scale apparatus has been constructed to monitor a tire as it is subjected to various loads and pressures. Digital image correlation is used to calculate the deformation in the tire. Using this method, damage resulting from a horizontal and vertical cut created on the tire surface could be detected. A three-dimensional surface reconstruction of the tire was created to assist in the characterization of more complex damage types such as wear and fatigue. In addition to providing information for a possible industrial scale damage detection system, this apparatus will also further the understanding of damage mechanisms in tires.

An assessment of electric vehicles: technology, infrastructure requirements, greenhouse-gas emissions, petroleum use, material use, lifetime cost, consumer acceptance and policy initiatives.

Science.gov (United States)

Delucchi, M A; Yang, C; Burke, A F; Ogden, J M; Kurani, K; Kessler, J; Sperling, D

2014-01-13

Concerns about climate change, urban air pollution and dependence on unstable and expensive supplies of foreign oil have led policy-makers and researchers to investigate alternatives to conventional petroleum-fuelled internal-combustion-engine vehicles in transportation. Because vehicles that get some or all of their power from an electric drivetrain can have low or even zero emissions of greenhouse gases (GHGs) and urban air pollutants, and can consume little or no petroleum, there is considerable interest in developing and evaluating advanced electric vehicles (EVs), including pure battery-electric vehicles, plug-in hybrid electric vehicles and hydrogen fuel-cell electric vehicles. To help researchers and policy-makers assess the potential of EVs to mitigate climate change and reduce petroleum use, this paper discusses the technology of EVs, the infrastructure needed for their development, impacts on emissions of GHGs, petroleum use, materials use, lifetime costs, consumer acceptance and policy considerations.

Effect of wheelchair mass, tire type and tire pressure on physical strain and wheelchair propulsion technique

NARCIS (Netherlands)

de Groot, Sonja; Vegter, Riemer J. K.; van der Woude, Lucas H. V.

2013-01-01

The purpose of this study was to evaluate the effect of wheelchair mass, solid vs. pneumatic tires and tire pressure on physical strain and wheelchair propulsion technique. 11 Able-bodied participants performed 14 submaximal exercise blocks on a treadmill with a fixed speed (1.11 m/s) within 3 weeks

Dynamics of vehicle-road coupled system

CERN Document Server

Yang, Shaopu; Li, Shaohua

2015-01-01

Vehicle dynamics and road dynamics are usually considered to be two largely independent subjects. In vehicle dynamics, road surface roughness is generally regarded as random excitation of the vehicle, while in road dynamics, the vehicle is generally regarded as a moving load acting on the pavement. This book suggests a new research concept to integrate the vehicle and the road system with the help of a tire model, and establishes a cross-subject research framework dubbed vehicle-pavement coupled system dynamics. In this context, the dynamics of the vehicle, road and the vehicle-road coupled system are investigated by means of theoretical analysis, numerical simulations and field tests. This book will be a valuable resource for university professors, graduate students and engineers majoring in automotive design, mechanical engineering, highway engineering and other related areas. Shaopu Yang is a professor and deputy president of Shijiazhuang Tiedao University, China; Liqun Chen is a professor at Shanghai Univ...

Replacing coal by tire powder in ceramic industry

Energy Technology Data Exchange (ETDEWEB)

Mothe, C.G. [Dept. de Processos Organicos, Escola de Quimica/CT/UFRJ, Rio de Janeiro, RJ (Brazil); Mothe Filho, H.F. [Dept. de Geociencias, Inst. de Agronomia/UFRRJ, Seropedica, RJ (Brazil)

2005-07-01

Nowadays preserving nature, recycling or reusing materials are good policies. Around ten million tires are put out by year in Brazil, and it is not known for how long they will remain in environment till their complete degradation. This research used tires to replace coal in ceramic processing. In this way it helps to protect environment, to reduce the consumption of mineral deposits and to save money. Results show that tire powder can replace coal to obtain ceramic material, using one percent of tire. Experiments were carried out using TA instruments SDT 2960, in air or nitrogen atmospheres, at heating rate of 10 C/min., flow 120 ml/min. TG/DTA curves of tire and coal have exothermic events at close temperatures between 450-600 C. At range of temperatures clay have endothermic events. (orig.)

Improvement of vehicle stability in cornering on uneven road; Akuro senkaiji ni okeru sharyo no anzensei kojo

Energy Technology Data Exchange (ETDEWEB)

Tobimatsu, K; Harada, M; Harada, H [National Defense Academy, Kanagawa (Japan)

1997-10-01

The active control of vehicle suspensions and rear wheel steering systems in turning on uneven roads is analyzed by means of LQR control theory, assuming that cornering forces depend on tire normal loads in addition to tire slip angles. The authors quantitatively investigated the effectiveness of the integrated control of the active suspension and the rear wheel steering, comparing the contributions of each individual system. Furthermore, in this paper, the role of the chassis control and driver control are studied in order to improve the stability of vehicle motion disturbed by the road surface. 4 refs., 9 figs.

Proceedings of Two Symposia on Nondestructive Testing of Tires

Science.gov (United States)

1978-05-01

understanding of this tire inspection area. But this better technical understanding will not guar - antee the success of either the industry or...control. Tires with very dark sur- face may be sprayed with talcum powder to improve their reflectance. Depending upon tire type and the required tire...products there has been a tendency to use some natural or synthetic cross-linking polymer gums which under extended heat conditions have tended to

49 CFR 229.75 - Wheels and tire defects.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A... two adjoining spots that are each two or more inches in length. (e) A seam running lengthwise that is...

Ontario tire recycling and economic development (OnTRED) plan : a market approach to eliminating tire stockpiles and promoting recycled rubber product manufacturing in Ontario

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-05-15

Details of the Ontario Tire Recycling and Economic Development (OnTRED) plan were presented. The plan was developed to address deficiencies in the Ontario Tire Stewardship's (OTS) Scrap Tire Diversion Program plan. The OTS promotes the burning of scrap tires contrary to the Waste Diversion Act, and transfers the financial responsibility for scrap tire management from manufacturers to retailers. The OnTRED plan will attempt to improve the current 87 per cent recovery rate for passenger scrap tires in Ontario, and prevent the formation of any new tire stockpiles. The aim of the OnTRED plan is to ensure reuse and recycling consistent with provisions in the Waste Diversion Act and enhance the existing workings of the tire and scrap tire market through the promotion of reuse and recycling. In addition, the plan aims to minimize administration and compliance costs. A program summary of the OnTRED plan was presented, as well as details of market development plans and buy-recycled rebates. Issues concerning collector registration and transaction tracking were presented, as well as details of brand-owner and first importer pay-in models. Stakeholder roles and responsibilities were reviewed. A budget scenario was presented, as well as a rebate and diversion scenario. It was concluded that Ontario's 87 per cent scrap tire diversion rate can be improved through a focus on patterns of reuse and recycling. 3 tabs., 7 figs.

An evaluation of string theory for the prediction of dynamic tire properties using scale model aircraft tires

Science.gov (United States)

Clark, S. K.; Dodge, R. N.; Nybakken, G. H.

1972-01-01

The string theory was evaluated for predicting lateral tire dynamic properties as obtained from scaled model tests. The experimental data and string theory predictions are in generally good agreement using lateral stiffness and relaxation length values obtained from the static or slowly rolling tire. The results indicate that lateral forces and self-aligning torques are linearly proportional to tire lateral stiffness and to the amplitude of either steer or lateral displacement. In addition, the results show that the ratio of input excitation frequency to road speed is the proper independent variable by which frequency should be measured.

A molecular dynamics (MD simulation on tire-aggregate friction

Directory of Open Access Journals (Sweden)

Fengyan Sun

2017-07-01

Full Text Available The friction between tire and road surface is fundamentally depending on the molecular forces. In this paper, the nanoscale 3D contact model is employed to investigate the tire-aggregate friction mechanism. The tire and aggregate micro-structure are both constructed to evaluate the microscopic performance of tire-aggregate friction influence. Simulation results show for a high velocity, the energy dissipation of sliding on crystal structure is small, which results in a small friction coefficient; temperature will have influences on the friction coefficient, and with the increasing of velocity, the effect will gradually reduce. Keywords: Tire, Aggregate, Friction coefficient, Microscopic mechanism, MD simulation

Leaching of DOC, DN, and inorganic constituents from scrap tires.

Science.gov (United States)

Selbes, Meric; Yilmaz, Ozge; Khan, Abdul A; Karanfil, Tanju

2015-11-01

One concern for recycle and reuse of scrap tires is the leaching of tire constituents (organic and inorganic) with time, and their subsequent potential harmful impacts in environment. The main objective of this study was to examine the leaching of dissolved organic carbon (DOC), dissolved nitrogen (DN), and selected inorganic constituents from scrap tires. Different sizes of tire chips and crumb rubber were exposed to leaching solutions with pH's ranging from 3.0 to 10.0 for 28days. The leaching of DOC and DN were found to be higher for smaller size tire chips; however, the leaching of inorganic constituents was independent of the size. In general, basic pH conditions increased the leaching of DOC and DN, whereas acidic pH conditions led to elevated concentrations of metals. Leaching was minimal around the neutral pH values for all the monitored parameters. Analysis of the leaching rates showed that components associated with the rubbery portion of the tires (DOC, DN, zinc, calcium, magnesium, etc.) exhibited an initial rapid followed by a slow release. On the other hand, a constant rate of leaching was observed for iron and manganese, which are attributed to the metal wires present inside the tires. Although the total amounts that leached varied, the observed leaching rates were similar for all tire chip sizes and leaching solutions. Operation under neutral pH conditions, use of larger size tire chips, prewashing of tires, and removal of metal wires prior to application will reduce the impact of tire recycle and reuse. Copyright © 2015 Elsevier Ltd. All rights reserved.

The in-plane deformation of a tire carcass: analysis and measurement

OpenAIRE

Xiong, Yi; Tuononen, Ari

2015-01-01

The deformation of parts of a tire is the direct result of tire–road interactions, and therefore is of great interest in tire sensor development. This case study focuses on the analysis of the deformation of the tire carcass and investigates its potential for the estimation of the in-plane tire force. The deformation of the tire carcass due to applied steady-state in-plane forces is first analyzed with the flexible ring model and then validated through optical tire sensor measurements. Couple...

Ground tire rubber as a stabilizer for subgrade soils.

Science.gov (United States)

2014-05-01

Over 250 million scrap tires are generated annually in the U.S. Historically, a significant portion of these tires : have been processed into finely ground tire rubber (GTR), or crumb rubber, for use as an additive in hot mix asphalt : (HMA) pavement...

Intelligent Torque Vectoring Approach for Electric Vehicles with Per-Wheel Motors

Directory of Open Access Journals (Sweden)

Alberto Parra

2018-01-01

Full Text Available Transport electrification is currently a priority for authorities, manufacturers, and research centers around the world. The development of electric vehicles and the improvement of their functionalities are key elements in this strategy. As a result, there is a need for further research in emission reduction, efficiency improvement, or dynamic handling approaches. In order to achieve these objectives, the development of suitable Advanced Driver-Assistance Systems (ADAS is required. Although traditional control techniques have been widely used for ADAS implementation, the complexity of electric multimotor powertrains makes intelligent control approaches appropriate for these cases. In this work, a novel intelligent Torque Vectoring (TV system, composed of a neuro-fuzzy vertical tire forces estimator and a fuzzy yaw moment controller, is proposed, which allows enhancing the dynamic behaviour of electric multimotor vehicles. The proposed approach is compared with traditional strategies using the high fidelity vehicle dynamics simulator Dynacar. Results show that the proposed intelligent Torque Vectoring system is able to increase the efficiency of the vehicle by 10%, thanks to the optimal torque distribution and the use of a neuro-fuzzy vertical tire forces estimator which provides 3 times more accurate estimations than analytical approaches.

World's largest off-road tires to be recycled

Energy Technology Data Exchange (ETDEWEB)

Anon.

2005-07-01

Suncor Energy is the first company in Canada to use a new technology designed uniquely for tire recycling at oil sand facilities. The technology is owned by CuttingEdge Tire Recycling, a partnership between Denesoline Environmental Limited Partnership and Beaver Environmental Rubber Technologies Limited. Suncor has supported the development of this Aboriginal-owned and operated business by offering land, electricity, diesel fuel and stockpiles of used truck tires from its oil sand mining activities. These tires are the largest off-road tires in the world. In this new technology, tires that are worn-out through oil sand mining are shredded in a portable shredder before being recycled for subsequent use by the Alberta Recycling Management Association. 1 fig.

Static tests of constructive tires using hydraulic press on the soil

OpenAIRE

Machado,Thiago M.; Lanças,Kléber P.; Oliveira Junior,Mauro B. de; Artioli,José A.; Marasca,Indiamara

2015-01-01

ABSTRACT The power consumption and load capacity of agricultural machines have grown and the effects of pressure on the soil by tires have been still little investigated. In concern with sustainable development, the relationship machine-tire-soil must be in balance to give more consistency on the best use of tires for a given load. This study aimed to evaluate four tires of two constructive types, the bias belted tires and radial tires, both with respective rim diameters of 22.5 and 26.5 inch...

76 FR 79114 - Tire Fuel Efficiency Consumer Information Program

Science.gov (United States)

2011-12-21

... car tires. The final rule also established reporting requirements for the generated performance... aspects of tire performance: rolling resistance, wet traction, and treadwear life.\\3\\ The final rule also... provide information indicating the relative performance of passenger car tires in the areas of treadwear...

75 FR 15893 - Tire Fuel Efficiency Consumer Information Program

Science.gov (United States)

2010-03-30

... how much the proposed consumer information program would affect consumer tire purchasing behavior and... 575 Tire Fuel Efficiency Consumer Information Program; Final Rule #0;#0;Federal Register / Vol. 75, No... 2127-AK45 Tire Fuel Efficiency Consumer Information Program AGENCY: National Highway Traffic Safety...

Polycyclic aromatic hydrocarbons, elemental and organic carbon emissions from tire-wear.

Science.gov (United States)

Aatmeeyata; Sharma, Mukesh

2010-09-15

Tire-wear is an important source of PAHs, elemental carbon (EC) and organic carbon (OC). The emissions of these pollutants have been studied in an experimental set-up, simulating a realistic road-tire interaction (summer tire-concrete road). The large particle non-exhaust emissions (LPNE; diameter greater than 10 microm) have been evaluated over 14,500 km run of the tire. An increasing linear trend with cumulative km run was observed for emissions of PAHs and carbon. Amongst PAHs in LPNE, pyrene has been observed to be the highest (30+/-4 mg kg(-1)) followed by benzo[ghi]perylene (17+/-2 mg kg(-1)). Different fractions of EC-OC for tire-wear have been analyzed, and unlike exhaust emissions, EC1 was observed to be 99% of EC whereas more than 70% of the OC was the high temperature carbon (OC3 and OC4). The overall emission factors (mass tire(-1) km(-1)) for PAHs, EC and OC from tire-wear are 378 ng tire(-1) km(-1), 1.46 mg tire(-1) km(-1) and 2.37 mg tire(-1) km(-1) for small cars. Copyright 2010 Elsevier B.V. All rights reserved.

Detection of tire tread particles using laser-induced breakdown spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Prochazka, David, E-mail: prochazka.d@fme.vutbr.cz [Brno University of Technology, Institute of Physical Engineering, Technická 2, 616 00 Brno (Czech Republic); Brno University of Technology, Central European Institute of Technology, Technická 3058/10, CZ-616 00 Brno (Czech Republic); Bilík, Martin [Brno University of Technology, Institute of Forensic Engineering, Údolní 244/53, 602 00 Brno (Czech Republic); Prochazková, Petra [Masaryk University, Faculty of Science, Department of Chemistry, Kamenice 735/5, 625 00 Brno (Czech Republic); Klus, Jakub; Pořízka, Pavel; Novotný, Jan [Brno University of Technology, Central European Institute of Technology, Technická 3058/10, CZ-616 00 Brno (Czech Republic); Novotný, Karel [Masaryk University, Faculty of Science, Department of Chemistry, Kamenice 735/5, 625 00 Brno (Czech Republic); Brno University of Technology, Central European Institute of Technology, Technická 3058/10, CZ-616 00 Brno (Czech Republic); Ticová, Barbora [Masaryk University, Faculty of Science, Department of Chemistry, Kamenice 735/5, 625 00 Brno (Czech Republic); Bradáč, Albert; Semela, Marek [Brno University of Technology, Institute of Forensic Engineering, Údolní 244/53, 602 00 Brno (Czech Republic); and others

2015-06-01

The objective of this paper is a study of the potential of laser induced breakdown spectroscopy (LIBS) for detection of tire tread particles. Tire tread particles may represent pollutants; simultaneously, it is potentially possible to exploit detection of tire tread particles for identification of optically imperceptible braking tracks at locations of road accidents. The paper describes the general composition of tire treads and selection of an element suitable for detection using the LIBS method. Subsequently, the applicable spectral line is selected considering interferences with lines of elements that might be present together with the detected particles, and optimization of measurement parameters such as incident laser energy, gate delay and gate width is performed. In order to eliminate the matrix effect, measurements were performed using 4 types of tires manufactured by 3 different producers. An adhesive tape was used as a sample carrier. The most suitable adhesive tape was selected from 5 commonly available tapes, on the basis of their respective LIBS spectra. Calibration standards, i.e. an adhesive tape with different area content of tire tread particles, were prepared for the selected tire. A calibration line was created on the basis of the aforementioned calibration standards. The linear section of this line was used for determination of the detection limit value applicable to the selected tire. Considering the insignificant influence of matrix of various types of tires, it is possible to make a simple recalculation of the detection limit value on the basis of zinc content in a specific tire. - Highlights: • LIBS experimental measurement parameters for tire tread particles were optimize. • Calibration curve was prepared. • Limit of detection was determined.

Detection of tire tread particles using laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Prochazka, David; Bilík, Martin; Prochazková, Petra; Klus, Jakub; Pořízka, Pavel; Novotný, Jan; Novotný, Karel; Ticová, Barbora; Bradáč, Albert; Semela, Marek

2015-01-01

The objective of this paper is a study of the potential of laser induced breakdown spectroscopy (LIBS) for detection of tire tread particles. Tire tread particles may represent pollutants; simultaneously, it is potentially possible to exploit detection of tire tread particles for identification of optically imperceptible braking tracks at locations of road accidents. The paper describes the general composition of tire treads and selection of an element suitable for detection using the LIBS method. Subsequently, the applicable spectral line is selected considering interferences with lines of elements that might be present together with the detected particles, and optimization of measurement parameters such as incident laser energy, gate delay and gate width is performed. In order to eliminate the matrix effect, measurements were performed using 4 types of tires manufactured by 3 different producers. An adhesive tape was used as a sample carrier. The most suitable adhesive tape was selected from 5 commonly available tapes, on the basis of their respective LIBS spectra. Calibration standards, i.e. an adhesive tape with different area content of tire tread particles, were prepared for the selected tire. A calibration line was created on the basis of the aforementioned calibration standards. The linear section of this line was used for determination of the detection limit value applicable to the selected tire. Considering the insignificant influence of matrix of various types of tires, it is possible to make a simple recalculation of the detection limit value on the basis of zinc content in a specific tire. - Highlights: • LIBS experimental measurement parameters for tire tread particles were optimize. • Calibration curve was prepared. • Limit of detection was determined

Study on profile measurement of extruding tire tread by laser

Science.gov (United States)

Wang, LiangCai; Zhang, Wanping; Zhu, Weihu

1996-10-01

This paper presents a new 2D measuring system-profile measurement of extruding tire tread by laser. It includes the thickness measurement of extruding tire tread by laser and the width measurement of extruding tire tread using Moire Fringe. The system has been applied to process line of extruding tire tread. Two measuring results have been obtained. One is a standard profile picture of extruding tire tread including seven measuring values. Another one is a series of thickness and width values. When the scanning speed thickness range is thickness < +/- 0.1mm.

Tire containing thermally exfoliated graphite oxide

Science.gov (United States)

Prud'homme, Robert K. (Inventor); Aksay, Ilhan A. (Inventor)

2011-01-01

A tire, tire lining or inner tube, containing a polymer composite, made of at least one rubber and/or at least one elastomer and a modified graphite oxide material, which is a thermally exfoliated graphite oxide with a surface area of from about 300 sq m/g to 2600 sq m/g.

A Planar Quasi-Static Constraint Mode Tire Model

Science.gov (United States)

2015-07-10

strikes a balance between simple tire models that lack the fidelity to make accurate chassis load predictions and computationally intensive models that...strikes a balance between heuristic tire models (such as a linear point-follower) that lack the fidelity to make accurate chassis load predictions...UNCLASSIFIED: Distribution Statement A. Cleared for public release A PLANAR QUASI-STATIC CONSTRAINT MODE TIRE MODEL Rui Maa John B. Ferris

New developments in tire derived fuels (TDF)

Energy Technology Data Exchange (ETDEWEB)

Hawkins, G. [Portland Cement Association, Skokie, IL (United States)

2006-07-01

Portland cement is a mixture of finely ground raw materials that are processed in a rotary kiln heated to 1500 degrees C by various fuels. Cooled clinker from the kiln is ground into portland cement. This presentation provided an overview of the role that tire-derived fuels is now playing in cement manufacturing. Data on the extent of TDF use in cement manufacturing processes were presented, as well as the results of air emissions monitoring programs conducted to assess the environmental impacts of TDF. During the cement manufacturing process, shredded and chipped tires are blown into the kiln to provide fuel, while whole tires are placed in the midpoint of long dry or wet kilns. For preheater and precalciner kilns, whole tires are added to raw material entering the kiln. The kiln's controlled combustion environment ensures the complete destruction of scrap tires. Approximately 130 million scrap tires were recycled in Portland cement plants in 2003. Forty-four portland cement plants are currently using TDF in North America. The United States Department of Energy has estimated that TDF produces less carbon dioxide (CO{sub 2}) per unit of energy than coal. Monitoring programs at Portland cement plants have indicated that the use of TDF in place of coal has resulted in moderate reductions of nitrogen oxide (NO{sub x}) emissions, slightly lower sulfuric oxide (SO{sub 2}) emissions and moderate reductions in carbon monoxide (CO). Some plants have reported slight reductions in particulate matter (PM) emissions. It was concluded that the use of scrap tires as a fuel reduces a waste stream and contributes to energy and raw material requirements. Moreover, plant air emissions are either reduced or are not impacted by TDF use. refs., tabs., figs.

Designing a Fuzzy Logic Controller to Enhance Directional Stability of Vehicles under Difficult Maneuvers

OpenAIRE

Mehrdad N. Khajavi; Golamhassan Paygane; Ali Hakima

2009-01-01

Vehicle which are turning or maneuvering at high speeds are susceptible to sliding and subsequently deviate from desired path. In this paper the dynamics governing the Yaw/Roll behavior of a vehicle has been simulated. Two different simulations have been used one for the real vehicle, for which a fuzzy controller is designed to increase its directional stability property. The other simulation is for a hypothetical vehicle with much higher tire cornering stiffness which is ca...

USING THE SCRAP TIRES TO PRODUCE A FLEXIBLE COUPLER

OpenAIRE

Tahsean A. Hussain

2018-01-01

The scrap tires considered a problematic source of waste, the old rubber tires causes a big environmental problem that is need much money and effort to disposes it safely. In Iraq there are more than two million used tires disposed to the environment annually. one of the tire’s recycling methods is the use of tire layers to produce a new rubber parts used in the engineering and industrial purposes as the bridges and machines dampers, this trend of recycling doesn’t take a sufficient care comp...

USING THE SCRAP TIRES TO PRODUCE A FLEXIBLE COUPLER

Directory of Open Access Journals (Sweden)

Tahsean A. Hussain

2018-01-01

Full Text Available The scrap tires considered a problematic source of waste, the old rubber tires causes a big environmental problem that is need much money and effort to disposes it safely. In Iraq there are more than two million used tires disposed to the environment annually. one of the tire’s recycling methods is the use of tire layers to produce a new rubber parts used in the engineering and industrial purposes as the bridges and machines dampers, this trend of recycling doesn’t take a sufficient care comparing with the other uses. There are a lot of studies conducted in these field, these studies suggests many methods to manage the huge number of scrap tires, the current paper aims to use the old rubber tires in engineering purposes (especially as a coupler joins the motor or engines with the other equipment as electric dynamo or pumps, the study focusing on the mechanical properties of a strip from a used tires and comparing with one prepared in the lab., and suggesting a new method to use as an engineering parts (for example the coupler lays between the IC engine and the dynamo of an electric generator. One of the results obtained from the experiments, there is no significant difference between the mechanical properties of the old and the new strip, (in the tensile test, the breaking force of the -Lab. tensile specimen- is 137 N whereas the specimen of old tire have a breaking force 113.27 N, but they are same in the elongation. A computational example is suggested to estimate the dimensions of a flexible coupler use an old tire pieces.

Robust two degree of freedom vehicle steering control satisfying mixed sensitivity constraint

OpenAIRE

Aksun-Güvenc, B.; Güvenc, L.; Odenthal, D.; Bünte, T.

2001-01-01

Robust steering control is used here for improving the yaw dynamics of a passenger car. A specific two degree of freedom control structure is adapted to the vehicle yaw dynamics problem and shown to robustly improve performance. The design study is based on six operating conditions for vehicle speed and the coefficient of friction between the tires and the road representing the operating domain of the vehicle. The relevant design specifications are formulated as attaining Hurwitz stability a...

Preliminary measurements on heat balance in pneumatic tires

Science.gov (United States)

Nybakken, G. H.; Collart, D. Y.; Staples, R. J.; Lackey, J. I.; Clark, S. K.; Dodge, R. N.

1973-01-01

A variety of tests was undertaken to determine the nature of heat generation associated with a pneumatic tire operating under various conditions. Tests were conducted to determine the magnitude and distribution of internally generated heat caused by hysteresis in the rubber and ply fabric in an automobile tire operating under conditions of load, pressure, and velocity representative of normal operating conditions. These included tests at various yaw angles and tests with braking applied. In other tests, temperature sensors were mounted on a road to measure the effect of a tire rolling over and an attempt was made to deduce the magnitude and nature of interfacial friction from the resulting information. In addition, tests were performed using the scratch plate technique to determine the nature of the motion between the tire and road. Finally, a model tire was tested on a roadwheel, the surface covering which could be changed, and an optical pyrometer was used to measure rubber surface temperatures.

Analysis of Tire Contact Parameters Using Visual Processing

Directory of Open Access Journals (Sweden)

Valentin Ivanov

2010-01-01

The first part of this paper presents the results of experimental estimation of the contact patch area depending on the normal wheel load and inflation pressure for different car tires. The data were obtained for test bench conditions on the basis of the visual processing of tread footprint. Further, the contact length in the cohesion area during wheel rolling for single points on the tire profile has been chosen as a benchmark criterion. This paper has analyzed the influence of the wheel normal load and tire inflation pressure on the contact length with small rolling velocities. The results of the investigations are given for winter and racing tires with different grades of wear.

Development of tire road noise chassis-dynamometer simulator. Effect of ISO surface replica model pad on tire road noise; Shisakushita tire romen soon shiken`yo jissha daijo simulator ni tsuite. ISO romen mogi pad wo sochakushita koka ni kansuru kisoteki kento

Energy Technology Data Exchange (ETDEWEB)

Tanaka, T; Murakami, T; Ogata, S; Sakamoto, I [Traffic Safety and Nuisance Research Inst., Tokyo (Japan)

1997-10-01

As a new test facility to clarify noise reduction method of tire road noise, Tire Road Noise Chassis-Dynamometer Simulator was developed. ISO surface replica pads made by copying the texture of ISO surface were attached on the roller surface of this system to simulate tire road noise. This paper described the specifications and characteristics of this system, and the effects of ISO surface replica pads on tire noise measurement by comparing the sound intensity in horizontal plane of tire noise measured in this system with that measured in a single drum tester with safety walk surface. 4 refs., 10 figs., 1 tab.

Final Scientific Report - "Improved Fuel Efficiency from Nanocomposite Tire Tread"

Energy Technology Data Exchange (ETDEWEB)

Dr. Andrew Myers

2005-12-30

Rolling resistance, a measure of the energy lost as a tire rotates while moving, is a significant source of power and fuel loss. Recently, low rolling resistant tires have been formulated by adding silica to tire tread. These "Green Tires" (so named from the environmental advantages of lower emissions and improved fuel economy) have seen some commercial success in Europe, where high fuel prices and performance drive tire selection. Unfortunately, the higher costs of the silica and a more complicated manufacturing process have prevented significant commercialization - and the resulting fuel savings - in the U.S. In this project, TDA Research, Inc. (TDA) prepared an inexpensive alternative to silica that leads to tire components with lower rolling resistance. These new tire composite materials were processed with traditional rubber processing equipment. We prepared specially designed nanoparticle additives, based on a high purity, inorganic mineral whose surface can be easily modified for compatibility with tire tread formulations. Our nanocomposites decreased energy losses to hysteresis, the loss of energy from the compression and relaxation of an elastic material, by nearly 20% compared to a blank SBR sample. We also demonstrated better performance than a leading silica product, with easier production of our final rubber nanocomposite.

Measuring service life and evaluating the quality of solid tires

Directory of Open Access Journals (Sweden)

Charoenyut Dechwayukul

2010-08-01

Full Text Available The objective of this research is to propose procedures for measuring service life and evaluating the quality of locallymade and used solid tires in Thailand. The solid tires were stressed and rotated until blowout on a drum-like test apparatuswhich is designed, constructed by the authors and equipped with laboratory instrumentation. Solid tires from five differentmanufacturers were selected for testing. We measured service life, length of time to tire failure, at three different loadingamplitudes and three different speeds on the testing drum. The service life of all specimens was studied and compared todetermine the possibility of using service life to evaluate the quality of a solid tire.

Development of fuel cell rubber tired tram (FRT)

Energy Technology Data Exchange (ETDEWEB)

Mok, J.K.; Chang, S.; Moon, K.H.; Lee, J.Y.; Koo, D.H. [Korea Railroad Research Inst., Uiwang (Korea, Republic of)

2006-07-01

This paper described a project to develop a fuel cell rubber-tired tram (FRT) transport system that both reduced emissions and increased operating efficiency in Seoul, Korea. The FRT was designed to have a transportation capacity of 2500 to 5000 persons per direction per hour, and a train set of 2 or 3 cars. Each vehicle was provided with a precise docking system in order to reduce boarding times. Vehicles were also equipped with low floors with easy access for handicapped and elderly passengers. The FRT system was primarily powered by fuel cells, had zero emissions, and were constructed of composite materials using a bimodal structure. The system was comprised of a hybrid power system with a combined compressed natural gas (CNG) and battery system alongside the fuel cell system. The paper included the results of a modelling study which examined the fuel cell at various energy production capacities. Details of the system's guidance system were also provided. Results of the modelling study showed that the FRT was capable of achieving the speed of a subway on roads and exclusive tracks through the use of a signaling system. 2 tabs., 8 figs.

26 CFR 48.4071-4 - Original equipment tires on imported articles.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Original equipment tires on imported articles..., Tread Rubber, and Taxable Fuel Tires, Tubes, and Tread Rubber § 48.4071-4 Original equipment tires on... than bicycle tires and inner tubes) that are original equipment for an imported article upon which no...

Photocatalytic Desulfurization of Waste Tire Pyrolysis Oil

Directory of Open Access Journals (Sweden)

Napida Hinchiranan

2011-11-01

Full Text Available Waste tire pyrolysis oil has high potential to replace conventional fossil liquid fuels due to its high calorific heating value. However, the large amounts of sulfurous compounds in this oil hinders its application. Thus, the aim of this research was to investigate the possibility to apply the photo-assisted oxidation catalyzed by titanium dioxide (TiO2, Degussa P-25 to partially remove sulfurous compounds in the waste tire pyrolysis oil under milder reaction conditions without hydrogen consumption. A waste tire pyrolysis oil with 0.84% (w/w of sulfurous content containing suspended TiO2 was irradiated by using a high-pressure mercury lamp for 7 h. The oxidized sulfur compounds were then migrated into the solvent-extraction phase. A maximum % sulfur removal of 43.6% was achieved when 7 g/L of TiO2 was loaded into a 1/4 (v/v mixture of pyrolysis waste tire oil/acetonitrile at 50 °C in the presence of air. Chromatographic analysis confirmed that the photo-oxidized sulfurous compounds presented in the waste tire pyrolysis oil had higher polarity, which were readily dissolved and separated in distilled water. The properties of the photoxidized product were also reported and compared to those of crude oil.

Distribution of sulphur into products from waste tire pyrolysis

International Nuclear Information System (INIS)

Susa, D.; Haydary, J.; Markos, J.

2012-01-01

Tire pyrolysis is getting growing attention as an effective waste tire disposal method in comparison to environmentally less friendly methods like dumping or incineration. But the scrap tire sulphur content can be a potential obstacle to scrap tire utilization as a fuel. In this paper the distribution of sulphur into tire pyrolysis yields, solid (char) and liquid (tar), was investigated. The pyrolysis experiments were carried out under different conditions to determine the partitioning of sulphur into pyrolysis products. The influence of different temperatures and reaction times was investigated in a laboratory flow reactor under nitrogen atmosphere. Solid and liquid residues were collected and analyzed by elemental analysis. The sulphur content in residual char and tar was determined using an elemental analyzer and the sulphur forms in tar were characterized by the X-ray photoelectron spectroscopy (XPS). (Authors)

The vehicle dynamics control system of Bosch; Die Fahrdynamikregelung von Bosch

Energy Technology Data Exchange (ETDEWEB)

Zanten, A.T. van [Robert Bosch GmbH, Stuttgart (Germany); Erhardt, R. [Robert Bosch GmbH, Stuttgart (Germany); Pfaff, G. [Robert Bosch GmbH, Stuttgart (Germany)

1996-11-01

Vehicle handling at the physical limit of adhesion between the tires and the road is extremely difficult. In such situations the driver may be supported by controlling the longitudinal and the lateral forces on the tires. The Vehicle Dynamics Control System of Bosch (VDC) does that by controlled braking of individual wheels which makes the vehicle motion approach the nomial motion intended by the driver. It uses signals to derive the driver`s intent (steering wheel angle, brake pressure, engine torque) and signals to dervie the actual motion of the vehicle (yaw rate, lateral acceleration). The support of the driver is not limited to coasting conditions. Also during full braking (ABS), partial braking, engine drag, free rolling and acceleration (ASR) of the vehicle the system supports the driver in all safety critical situations. In this paper an overview of the VDC is given. The goal of the development of VDC, the physical background, the concept of the system, the control and the controller algorithm are described. The benefit of VDC is demonstrated by an experimental test. (orig.) [Deutsch] Fahrdynamikregelsysteme FDR sind Regelsysteme im Bremssystem und Antriebsstrang, die das seitliche Ausbrechen des Fahrzeugs verhindern. Waehrend ABS das Blockieren der Raeder beim Bremsen und ASR das Durchdrehen der Raeder beim Antrieb verhindert, verhindert FDR das Schleudern und das Schieben des Fahrzeugs. (orig.)

COMPUTATIONAL AND EXPERIMENTAL EVALUATION OF TECHNICAL CHARACTERISTICS OF TRUCKS TIRES

Directory of Open Access Journals (Sweden)

Z. A. Godzhaev

2015-01-01

Full Text Available Now improvement of technological design specification of trucks tires develops very much. In modern mechanical engineering polyamide and kapron cords for tires of line-haul trucks and buses are replaced with all-metal ones (AMC even more often. It was defined that at increase in AMC tires production their technical characteristics were investigated insufficiently. In this regard there were carried out bench tests to compare the main operational indicators of domestic (JSC Nizhnekamskshina production and foreign tires with an all-metal cord: 315/60R22.5 the NF-201 model with 315/60r22.5 the XZA2 ENERGY Michelin model (steering; 315/60R22.5 the NR-201 model with 315/60R22.5 the XDA2+ ENERGY Michelin model (drive; 315/80R22.5 the NF-201 model with 315/80R22.5 the 3D Michelin XZE X MultiWay model (steering; 315/80R22.5 the NR-201 model with 315/80R22.5 the 3D XDE X MultiWay model (drive. The laboratory researches were carried out for the purpose of an assessment of the universal, load, damping (hysteresis and other characteristics of tires with use of the universal functional SIB-1M test-bench. It was established that Michelin AMC tires of steering low-profile 315/60R22.5 XZA2 ENERGY models have the best indicators on power heterogeneity - 0.47-0.89 percent. The high-profile AMC tires of drive wheels 315/80R22.5 of the NR-201 model of JSC Nizhnekamskshina have the worst indicators. However, all the tested tires correspond to GOST 5513-97on this indicator. It was noted that Nizhnekamsk AMC tires of the size 315/60R22.5 are flush with AMC tires Michelin on set of operational indicators, except power heterogeneity, and last one of Michelin tires is lower than Nizhnekamsk ones by 2-3 times. It was suggested to conduct further researches on definition of optimum operational tires indicators because of an intensive use of KAMAZ trucks in agricultural production

Ground tire rubber as a stabilizer for subgrade soils : [summary].

Science.gov (United States)

2014-05-01

Over 250 million scrap tires are generated : annually in the U.S. Historically, a significant : portion of these tires have been processed into : finely ground tire rubber (GTR), or crumb rubber, : for use as an additive in hot mix asphalt (HMA) : pa...

Golf Blue-e-Motion. The electric Volkswagen; Golf Blue-e-Motion. Der elektrische Volkswagen

Energy Technology Data Exchange (ETDEWEB)

Hadler, Jens; Neusser, Heinz-Jakob; Jelden, Hanno; Lueck, Peter; Tousen, Jonas [Volkswagen AG, Wolfsburg (Germany)

2012-11-01

The particular challenges of our time require a consistent focus on the development activities of powertrain technologies with continuously reduced fuel consumption and CO2 emissions. The past years have seen many technological milestones by Volkswagen's Powertrain Development as illustrated by the exceptional success of the TSI and TDI engines as well as the double clutch transmissions. As a part of this comprehensive list of powertrain strategy, the development of drivetrains for alternative fuels, such as CNG, has also been included. With particular emphasis Volkswagen is pressing forward the electrification of the drivetrain with the goal of appealing to more customers through these new technologies. A milestone of the electrification activity is the Golf Blue-e-Motion, in which the comfort and especially the city driving performance are improved compared with the conventional vehicle. This driving performance is achieved by an electric drivetrain which consists of a permanent magnet synchronous electric motor together with associated power electronics and a Li-Ion battery. This presentation will pay particular attention to the characteristics of the drivetrain system and its components. The efficient powertrain including the recovering of braking energy (recuperation) as well as the attention paid on optimising all system components, has increased the driving range of the vehicle. Environmental awareness and driving pleasure - the electric drivetrain of the Golf Blue-e-Motion shows that these both requirements are possible to be realised by an electric drivetrain. (orig.)

Dynamic performances analysis of a real vehicle driving

Science.gov (United States)

Abdullah, M. A.; Jamil, J. F.; Salim, M. A.

2015-12-01

Vehicle dynamic is the effects of movement of a vehicle generated from the acceleration, braking, ride and handling activities. The dynamic behaviours are determined by the forces from tire, gravity and aerodynamic which acting on the vehicle. This paper emphasizes the analysis of vehicle dynamic performance of a real vehicle. Real driving experiment on the vehicle is conducted to determine the effect of vehicle based on roll, pitch, and yaw, longitudinal, lateral and vertical acceleration. The experiment is done using the accelerometer to record the reading of the vehicle dynamic performance when the vehicle is driven on the road. The experiment starts with weighing a car model to get the center of gravity (COG) to place the accelerometer sensor for data acquisition (DAQ). The COG of the vehicle is determined by using the weight of the vehicle. A rural route is set to launch the experiment and the road conditions are determined for the test. The dynamic performance of the vehicle are depends on the road conditions and driving maneuver. The stability of a vehicle can be controlled by the dynamic performance analysis.

Tire aging: a human factors analysis of failure to warn and inform.

Science.gov (United States)

Wogalter, Michael S; Laughery, Kenneth R

2012-01-01

A scenario of an automotive accident caused by tire failure is given followed by a human factors analysis of the information available to consumers on tire aging. Consumers have not been told that the age of the tire is a safety concern. It is not easy to decode the date of manufacture on tires. More publicity and prominent warnings are needed to communicate the dangers of older tires. Also, better ways to present the date of manufacture so that consumers can more easily and accurately assess tire age are needed.

78 FR 66655 - Consumer Information; Uniform Tire Quality Grading Standards

Science.gov (United States)

2013-11-06

... information indicating the relative performance of passenger car tires in the areas of treadwear, traction... [Docket No. NHTSA-2013-0120] RIN 2127-AL49 Consumer Information; Uniform Tire Quality Grading Standards...). ACTION: Interim final rule; request for comments. SUMMARY: The Uniform Tire Quality Grading Standards...

Forensic analysis of tire rubbers based on their sulfur chemical states.

Science.gov (United States)

Funatsuki, Atsushi; Shiota, Kenji; Takaoka, Masaki; Tamenori, Yusuke

2015-05-01

The chemical states of sulfur in 11 tires were analyzed using X-ray absorption near-edge structure (XANES) in order to discriminate between various tire rubbers. All tires had peaks around 2471.5 and 2480.5eV, and the shapes and heights of these peaks differed among tires, suggesting that the sulfur chemical state could be used for discrimination between tire rubbers. Based on t-tests on the results of XANES, 43 of 55 combinations were different at a significance level of 5%. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Characterization of pyrolytic oil obtained from pyrolysis of TDF (Tire Derived Fuel)

International Nuclear Information System (INIS)

Banar, Müfide; Akyıldız, Vildan; Özkan, Aysun; Çokaygil, Zerrin; Onay, Özlem

2012-01-01

Highlights: ► We pyrolyzed Tire Derived Fuel (TDF) at different heating rates and temperatures. ► We determine convenient pyrolysis temperature for pyrolytic oil. ► The product can be used as fuel for combustion system in industry. ► TDF pyrolysis is advisable recycling system because of low hazardous constituents. - Abstract: In recent years, waste utilization before disposing to the land is the most important point about waste management. Due to the increasing emphasis on recycling, related to the two European Commission Directives (EC End of Life Vehicle Directive, EC Waste Landfill Directive) affecting the management of waste tires, there is interest in the development of alternative technologies for recycling waste tires. One of them is pyrolysis. For this purpose, a fixed bed reactor was used to pyrolysis of Tire Derived Fuel (TDF) at the temperatures of 350, 400, 450, 500, 550 and 600 °C with the heating rates of 5 and 35 °C/min. The maximum pyrolytic oil yield (38.8 wt.%) was obtained at 400 °C with 5 °C/min heating rate. The yield of pyrolytic oil decreased with increasing pyrolysis temperatures whereas the yield of gases increased. The fuel properties of the pyrolytic oil including higher heating value (HHV), elemental composition, flash point, viscosity, distillation and density were determined. Pyrolytic oil was characterized by fourier transform infrared spectroscopy (FT-IR), hydrogen nuclear magnetic resonance spectroscopy ( 1 H NMR) and gas chromatography–mass spectroscopy (GC–MS) techniques and also, the amount of polychlorinated dibenzodioxins/polychlorinated dibenzofurans (PCDDs/PCDFs) and congener distribution characteristics were studied for determination of environmental effects. It was seen that the pyrolytic oils have similar fuel properties with the diesel. It was also found that pyrolytic oil contained 0.00118 I-TEQs/g at very low level. Finally, the pyrolytic oil can be evaluated for energy recovery according to Regulation

Combustion of used tires for energy recovery. Yozumi taiya shokyaku ni suru netsuriyo

Energy Technology Data Exchange (ETDEWEB)

Ishizawa, N. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

1993-03-15

The recycled automobile tires in 1991 amounts to 87%, and the tires are used most effectively for heat generation. The utilization of tires for heat in Japan and in other countries are outlined, and a detailed report is made on the use of used tires as fuel at coal cogeneration plants in tire manufacturing plants. The 'utilization percent for heat' is steadily increasing among the recycling applications of used tires. Energy recovery by dry distillation method and by direct combustion method is discussed. The states of used tire utilization in America, West Germany, and Britain are introduced. A concrete example of utilization for heat of used tires at a tire manufacturing plant is shown. Used tires are chopped into chips, mixed and burned in a coal boiler, the generated steam is used as the heat source for private power generation, and the power is used as the power source for the plant. 15 refs., 5 figs., 7 tabs.

NUMERICAL MODELLING AND EXPERIMENTAL INFLATION VALIDATION OF A BIAS TWO-WHEEL TIRE

Directory of Open Access Journals (Sweden)

CHUNG KET THEIN

2016-02-01

Full Text Available This paper presents a parametric study on the development of a computational model for bias two-wheel tire through finite element analysis (FEA. An 80/90- 17 bias two-wheel tire was adopted which made up of four major layers of rubber compound with different material properties to strengthen the structure. Mooney-Rivlin hyperelastic model was applied to represent the behaviour of incompressible rubber compound. A 3D tire model was built for structural static finite element analysis. The result was validated from the inflation analysis. Structural static finite element analysis method is suitable for evaluation of the tire design and improvement of the tire behaviour to desired performance. Experimental tire was inflated at various pressures and the geometry between numerical and experimental tire were compared. There are good agreements between numerical simulation model and the experiment results. This indicates that the simulation model can be applied to the bias two-wheel tire design in order to predict the tire behaviour and improve its mechanical characteristics.

Blast overpressure after tire explosion: a fatal case.

Science.gov (United States)

Pomara, Cristoforo; D'Errico, Stefano; Riezzo, Irene; Perilli, Gabriela; Volpe, Umberto; Fineschi, Vittorio

2013-12-01

Fatal blast injuries are generally reported in literature as a consequence of the detonation of explosives in war settings. The pattern of lesion depends on the position of the victim in relation to the explosion, on whether the blast tracks through air or water, and whether it happens in the open air or within an enclosed space and the distance from the explosion. Tire explosion-related injuries are rarely reported in literature. This study presents a fatal case of blast overpressure due to the accidental explosion of a truck tire occurring in a tire repair shop. A multidisciplinary approach to the fatality involving forensic pathologists and engineers revealed that the accidental explosion, which caused a series of primary and tertiary blast wave injuries, was due to tire deterioration.

Spray From a Rolling Tire: Mechanics of Droplet Formation

Science.gov (United States)

Plocher, Dennis; Browand, Fred

2010-11-01

The spray pattern immediately behind a single-groove tire rolling on a wet surface is produced in the laboratory using a specially designed tire spray simulator. The spray development is examined using high speed video. Water from the groove forms a liquid sheet as the tire-tread lifts away from the surface. The sheet is not of uniform thickness, but it remains attached to the tread. The thinner portions of the sheet become even thinner as the tire rotates, and eventually break to produce holes near the tire surface. The holes grow as the sheet margins surrounding the holes retract into the thicker portions of the sheet which become roughly cylindrical "ligaments" aligned at right angles to the direction of spray motion. The ligaments break into large droplets via a Rayleigh instability. The smallest droplets form when the margins of two holes collide. As Weber number, We = ρU^2w/2σ , based on tire groove half width, w/2, varies by a factor of 25, the sheet-ligament structure persists, but ligaments become less organized, and more small droplets appear in the pattern.

49 CFR 575.106 - Tire fuel efficiency consumer information program.

Science.gov (United States)

2010-10-01

... to provide information indicating the relative performance of replacement passenger car tires in the... achieve the level of performance represented by each rating. (A) Ratings. Each tire shall be rated with... 49 Transportation 7 2010-10-01 2010-10-01 false Tire fuel efficiency consumer information program...

Influence of tire inflating pressure at dynamic forces acting on articulated trolleybus

Directory of Open Access Journals (Sweden)

Polach Pavel

2017-01-01

Full Text Available ŠKODA VÝZKUM s.r.o. cooperated on the development of the NEOPLAN DMA low-floor articulated trolleybus intended for the Boston city. Multibody models and finite element models of the trolleybus were utilized in the stage of the vehicle design. At the end of the stage of computer modelling and testing of the trolleybus prototype a decision to reduce tire inflating of vehicles in serial production (together with the change the type of shock absorbers used in trolleybus suspension was made. The impact of this change on forces acting in the trolleybus suspension elements (i.e. in air springs and shock absorbers and radius rods on the trolleybus chassis when running on an uneven test track was investigated using multibody simulations. Time histories of the forces calculated utilising multibody models were used as input data of the trolleybus finite element models.

Tire recycling technologies: What is the future?

NARCIS (Netherlands)

Saiwari, Sitisaiyidah; van Hoek, Johannes Wilhelmus; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.; Blume, Anke; Heideman, G.

2016-01-01

Recycling is a heavily discussed topic nowadays, and recycled tire material to be re-used for the same application is one of the spear points of current R&D activities. Regarding the immense amount of used tires, more than just one outlet for the recycled material is needed. Besides the commonly

Evaluation of bifenthrin applications in tires to prevent Aedes mosquito breeding.

Science.gov (United States)

Nguyen, Huy T; Whelan, Peter I; Shortus, Matthew S; Jacups, Susan P

2009-03-01

The efficacy of maximum label rates of bifenthrin applications to dry tires to prevent Aedes mosquito breeding was investigated by field colonization and bioassay trials in shaded and unshaded locations. Aedes notoscriptus and Culex quinquefasciatus larvae were the most abundant species present in the field colonization trial. Colonization and survival of Ae. notoscriptus larvae to the late instar occurred significantly earlier in treated tires in shaded compared with unshaded locations (P = 0.002). Bifenthrin applications in shaded tires only prevented early instar survival for approximately 2.6 wk. Aedes notoscriptus late instars did not appear in the treated unshaded tires. Culex quinquefasciatus colonized treated tires from the 2nd wk in both shaded and unshaded treatments. In the bioassay, water from bifenthrin-treated tires, through extrapolation, was found to kill approximately 100% of late instar Ae. notoscriptus for only approximately 2.0-2.2 wk in shaded and unshaded tires. Under conditions optimal for Aedes breeding, such as shaded locations, high ambient temperatures, high relative humidity, and high amounts of leaf/organic matter accumulations, bifenthrin may not be effective as a larval control measure in tires for greater than 2.0-2.6 wk.

Dynamic force profile in hydraulic hybrid vehicles: a numerical investigation

Science.gov (United States)

Mohaghegh-Motlagh, Amin; Elahinia, Mohammad H.

2010-04-01

A hybrid hydraulic vehicle (HHV) combines a hydraulic sub-system with the conventional drivetrain in order to improve fuel economy for heavy vehicles. The added hydraulic module manages the storage and release of fluid power necessary to assist the motion of the vehicle. The power collected by a pump/motor (P/M) from the regenerative braking phase is stored in a high-pressure accumulator and then released by the P/M to the driveshaft during the acceleration phase. This technology is effective in significantly improving fuel-economy for heavy-class vehicles with frequent stop-and-go drive schedules. Despite improved fuel economy and higher vehicle acceleration, noise and vibrations are one of the main problems of these vehicles. The dual function P/Ms are the main source of noise and vibration in a HHV. This study investigates the dynamics of a P/M and particularly the profile and frequency-dependence of the dynamic forces generated by a bent-axis P/M unit. To this end, the fluid dynamics side of the problem has been simplified for investigating the system from a dynamics perspective. A mathematical model of a bent axis P/M has been developed to investigate the cause of vibration and noise in HHVs. The forces are calculated in time and frequency domains. The results of this work can be used to study the vibration response of the chassis and to design effective vibration isolation systems for HHVs.

Who benefited from the US tariffs on the Chinese tires?

OpenAIRE

Joonhyung, Lee

2011-01-01

The purpose of this paper is to evaluate the short-run effect of the tariffs on Chinese tires imposed by the US in September 2009. First, we investigated whether the tariffs were beneficial to the US domestic tire industry in terms of employment. Our empirical analysis found that there were no significant benefits to US employment in the tire industry. This result led us to the next question: Who benefited from the tariffs? We found that the tire imports to the US were significantly deviated ...

Oxidative desulfurization of tire pyrolysis oil

OpenAIRE

Ahmad Shahzad; Ahmad Muhammad Imran; Naeem Khawar; Humayun Muhammad; Sebt-E-Zaeem; Faheem Farrukh

2016-01-01

This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure a...

Tire deflation device

Science.gov (United States)

Barker, Stacey G [Idaho Falls, ID

2010-01-05

A tire deflation device includes (1) a component having a plurality of bores, (2) a plurality of spikes removably insertable into the plurality of bores and (3) a keeper within each among the plurality of bores, the keeper being configured to contact a sidewall surface of a spike among the plurality of spikes and to exert force upon the sidewall surface. In an embodiment, the tire deflation device includes (a) a component including a bore in a material, the bore including a receiving region, a sidewall surface and a base surface, (b) a channel extending from the sidewall surface into the material, (c) a keeper having a first section housed within the channel and a second section which extends past the sidewall surface into the receiving region, and (d) a spike removably insertable into the bore.

Laser cleaning of the contaminations on the surface of tire mould

Science.gov (United States)

Ye, Yayun; Jia, Baoshen; Chen, Jing; Jiang, Yilan; Tang, Hongping; Wang, Haijun; Luan, Xiaoyu; Liao, Wei; Zhang, Chuanchao; Yao, Caizhen

2017-07-01

During the manufacturing of tires, surface pollutants on tire mould will lead to the production of unqualified tires. Tire moulds need to be regularly cleaned. Laser cleaning is recognized as a non-destructive, effective, precise and environmental friendly method. In this paper, laser cleaning was used to remove contaminants on tire mould surface. First, laser induced damage experiments were performed. The results showed that the roughness and hardness of the cast steel sample surface seldom changed under the energy range of 140.1-580.2 mJ laser irradiation 1 pulse and the energy range of 44.7-168.9 mJ laser irradiation 100 pulses. In the laser cleaning experiments, the cleaning thresholds and the optimal cleaning parameters were obtained. Results indicated that laser cleaning was safe and effective for tire mould contamination removal.

49 CFR 579.26 - Reporting requirements for manufacturers of tires.

Science.gov (United States)

2010-10-01

... imported is less than 15,000, or are deep tread, winter-type snow tires, space-saver or temporary use spare... 49 Transportation 7 2010-10-01 2010-10-01 false Reporting requirements for manufacturers of tires... requirements for manufacturers of tires. For each reporting period, a manufacturer (including a brand name...

Application of granulating of tires; Aplicaciones de granulado de NFUs

Energy Technology Data Exchange (ETDEWEB)

Jimenez Justicia, A.

2001-07-01

At present, used tires are mainly used as fuel, retreading and granulating of tires. In this article. I will focus on the last option, talking about some of the multiple applications and going into detail of the making process of the granulation of used tires in a recycling plant. (Author)

Tire-Pavement Friction Characteristics with Elastic Properties of Asphalt Pavements

Directory of Open Access Journals (Sweden)

Miao Yu

2017-11-01

Full Text Available The skid-resisting performance of pavement is a critical factor in traffic safety. Recent studies primarily analyze this behavior by examining the macro or micro texture of the pavement. It is inevitable that skid-resistance declines with time because the texture of pavement deteriorates throughout its service life. The primary objective of this paper is to evaluate the use of different asphalt pavements, varying in resilience, to optimize braking performance on pavement. Based on the systematic dynamics of tire-pavement contact, and analysis of the tire-road coupled friction mechanism and the effect of enlarging the tire-pavement contact area, road skid resistance was investigated by altering the elastic modulus of asphalt pavement. First, this research constructed the kinetic contact model to simulate tire-pavement friction. Next, the following aspects of contact behaviors were studied when braking: tread deformation in the tangential pavement interface, actual tire-pavement contact in the course, and the frictional braking force transmitted from the pavement to the tires. It was observed that with improvements in pavement elasticity, the actual tire-pavement contact area increased, which gives us the ability to effectively strengthen the frictional adhesion of the tire to the pavement. It should not be overlooked that the improvement in skid resistance was caused by an increase in pavement elasticity. This research approach provides a theoretical basis and design reference for the anti-skid research of asphalt pavements.

Properties of concrete containing scrap-tire rubber--an overview.

Science.gov (United States)

Siddique, Rafat; Naik, Tarun R

2004-01-01

Solid waste management is one of the major environmental concerns in the United States. Over 5 billion tons of non-hazardous solid waste materials are generated in USA each year. Of these, more than 270 million scrap-tires (approximately 3.6 million tons) are generated each year. In addition to this, about 300 million scrap-tires have been stockpiled. Several studies have been carried out to reuse scrap-tires in a variety of rubber and plastic products, incineration for production of electricity, or as fuel for cement kilns, as well as in asphalt concrete. Studies show that workable rubberized concrete mixtures can be made with scrap-tire rubber. This paper presents an overview of some of the research published regarding the use of scrap-tires in portland cement concrete. The benefits of using magnesium oxychloride cement as a binder for rubberized concrete mixtures are also presented. The paper details the likely uses of rubberized concrete.

Beam response analysis of moving vehicle with half car modeling

International Nuclear Information System (INIS)

Badriyah, A.N.; Arifianto, D.; Susatio, Y.

2016-01-01

There were several tragedies concerning damages of bridge which seem to be sooner than the predicted period. One of hypothesis in this situation is an addition of vibration caused by long vehicle such as super long truck which has huge force transferred into the bridge and its long body causes more vibration due to phase difference of front and rear tire. The selected method which is used in this problem is using a simulation for modeling a bridge- vehicle system using half car vehicle model. The simulation is done using ANSYS Workbench 15.0 with some variation such us the thickness of beam and its supports. There are 3 kind of variation used in the thickness variety which are 2 m, 1 m, and 0.5 m. While in supports variation, we have fixed support, knife-edge support, and slider support. The results show that there is addition of vibration caused by long vehicle. It is proved by an oscillation which is showed in every response of beam's total deformation. Highest total deformation is achieved in slider support beam of 0.5 thicknesses, 1.08 mm in 1.12 second. First ripple seen in responses is at 0.84 second. Meanwhile, response of knife-edge and fixed support beam show a similarity. The ripple in this situation is caused by beat modulation from the front and rear tire. (paper)

Beam response analysis of moving vehicle with half car modeling

Science.gov (United States)

Badriyah, A. N.; Arifianto, D.; Susatio, Y.

2016-11-01

There were several tragedies concerning damages of bridge which seem to be sooner than the predicted period. One of hypothesis in this situation is an addition of vibration caused by long vehicle such as super long truck which has huge force transferred into the bridge and its long body causes more vibration due to phase difference of front and rear tire. The selected method which is used in this problem is using a simulation for modeling a bridge- vehicle system using half car vehicle model. The simulation is done using ANSYS Workbench 15.0 with some variation such us the thickness of beam and its supports. There are 3 kind of variation used in the thickness variety which are 2 m, 1 m, and 0.5 m. While in supports variation, we have fixed support, knife-edge support, and slider support. The results show that there is addition of vibration caused by long vehicle. It is proved by an oscillation which is showed in every response of beam's total deformation. Highest total deformation is achieved in slider support beam of 0.5 thicknesses, 1.08 mm in 1.12 second. First ripple seen in responses is at 0.84 second. Meanwhile, response of knife-edge and fixed support beam show a similarity. The ripple in this situation is caused by beat modulation from the front and rear tire.

26 x 6.6 radial-belted aircraft tire performance

Science.gov (United States)

Davis, Pamela A.; Martinson, Veloria J.; Yager, Thomas J.; Stubbs, Sandy M.

1991-01-01

Preliminary results from testing of 26 x 6.6 radial-belted and bias-ply aircraft tires at NASA Langley's Aircraft Landing Dynamics Facility (ALDF) are reviewed. The 26 x 6.6 tire size evaluation includes cornering performance tests throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Static test results to define 26 x 6.6 tire vertical stiffness properties are also presented and discussed.

Evaluation of substitution monopole models for tire noise sound synthesis

Science.gov (United States)

Berckmans, D.; Kindt, P.; Sas, P.; Desmet, W.

2010-01-01

Due to the considerable efforts in engine noise reduction, tire noise has become one of the major sources of passenger car noise nowadays and the demand for accurate prediction models is high. A rolling tire is therefore experimentally characterized by means of the substitution monopole technique, suiting a general sound synthesis approach with a focus on perceived sound quality. The running tire is substituted by a monopole distribution covering the static tire. All monopoles have mutual phase relationships and a well-defined volume velocity distribution which is derived by means of the airborne source quantification technique; i.e. by combining static transfer function measurements with operating indicator pressure measurements close to the rolling tire. Models with varying numbers/locations of monopoles are discussed and the application of different regularization techniques is evaluated.

EVALUATION OF TIRE RUBBER DISPOSAL IN CONCRETE FOR PAVEMENTS

Directory of Open Access Journals (Sweden)

Rosa Cristina Cecche Lintz

2009-01-01

Full Text Available The production of waste by the tire industry has been a growing problem, indicating the need for its reuse. More than thirty million tires are discharged per year in Brazil, where regulation for the environment states that for each four new tires, five unusable ones must be adequately disposed by manufacturers and importers. Paving consumes an extremely large quantity of materials, which can be the source of rational application of waste and rejected materials. Research shows that tire rubber can be added to asphalt, which increases its durability and improves pavement quality and safety conditions by absorbing the rubber elastic properties, and also be used for architectural applications, among others. This study deals with the addition of rubber fibers from tire crushing in concrete for roadway pavements in order to provide proper indication about the alternative material disposal through an evaluation of the mechanical behavior of the modified concrete. Different concrete mixes were produced, within which, part of fine aggregates were substituted by tire rubber and mechanical experiment tests were performed, which show that, due to great resistance losses, the disposal of this alternative material in concrete should be considered for light traffic pavements, with the addition of rubber ranging up to 10% in mass.

EVALUATION OF TIRE RUBBER DISPOSAL IN CONCRETE FOR PAVEMENTS

Directory of Open Access Journals (Sweden)

Rosa Cristina Cecche Lintz

2009-12-01

Full Text Available The production of waste by the tire industry has been a growing problem, indicating the need for its reuse. More than thirty million tires are discharged per year in Brazil, where regulation for the environment states that for each four new tires, five unusable ones must be adequately disposed by manufacturers and importers. Paving consumes an extremely large quantity of materials, which can be the source of rational application of waste and rejected materials. Research shows that tire rubber can be added to asphalt, which increases its durability and improves pavement quality and safety conditions by absorbing the rubber elastic properties, and also be used for architectural applications, among others. This study deals with the addition of rubber fibers from tire crushing in concrete for roadway pavements in order to provide proper indication about the alternative material disposal through an evaluation of the mechanical behavior of the modified concrete. Different concrete mixes were produced, within which, part of fine aggregates were substituted by tire rubber and mechanical experiment tests were performed, which show that, due to great resistance losses, the disposal of this alternative material in concrete should be considered for light traffic pavements, with the addition of rubber ranging up to 10% in mass.

A novel wireless piezoelectric tire sensor for the estimation of slip angle

International Nuclear Information System (INIS)

Erdogan, G; Alexander, L; Rajamani, R

2010-01-01

This paper introduces a simple approach for the analysis of tire deformation and proposes a new piezoelectric tire sensor for physically meaningful measurements of tire deformations. Tire deformation measurements in the contact patch can be used for the estimation of slip angle, tire forces, slip ratio and tire–road friction coefficient. The specific case of a wireless tire deformation sensor for the estimation of slip angle is taken up in this paper. A sensor in which lateral sidewall deformation can be decoupled from radial deformation is designed. The slope of the lateral deflection curve in the contact patch is used to calculate slip angle. A specially constructed tire test rig is used to experimentally evaluate the performance of the developed sensor. Results show that the developed sensor can accurately estimate slip angles up to values of 5°

On long-term fatigue damage and reliability analysis of gears under wind loads in offshore wind turbine drivetrains

OpenAIRE

Rasekhi Nejad, Amir; Gao, Zhen; Moan, Torgeir

2014-01-01

In this paper, a long-term fatigue damage analysis method for gear tooth root bending in wind turbine’s drivetrains is presented. The proposed method is established based on the ISO gear design codes which are basically developed for gears in general applications, not specifically for wind turbine gears. The ISO procedure is adapted and further improved to include the long-term fatigue damage of wind turbine’s gears. The load duration distribution (LDD) method is used to obtain the short-term...

Rubber - application of radiation to tire manufacture

International Nuclear Information System (INIS)

Hunt, J.D.; Alliger, G.

1979-01-01

Since the advent of commercial accelerators during the last several years capable of producing controllable electron beams of high energy, Firestone has devoted a considerable effort to the better understanding of the possible applications of such radiation to the production of tires or tire components. A number of chemical reactions can occur when elastomeric compounds are exposed to high energy waves, but crosslinking and degradation are the most important. The degree to which the crosslinking reaction predominates depends upon the nature of the rubber, compounding ingredients and the dosage. In general then, the effects achieved by the radiation of a rubber are quite similar to those resulting from heat. However, radiation cure or precure of compounds offers the advantage that the degree of crosslinking can be better controlled. Uniform crosslinking is possible since the high speed electrons penetrate uniformly throughout the sample. Curing with heat on the other hand may result in a greater degree of crosslinking on the surface of the sample than the center because of low heat conductivity. In general, radiation can be used to advantage to crosslink partially rubber tire components so that they retain better their shape and dimension during tire assembly and final cure or vulcanization. Added advantages of radiation precure include: a reduction of material usage, substitution of synthetic for natural rubber without loss in strength and the fact that partially crosslinked components will not thin out or become displaced during construction and vulcanization of the tire. (author)

Flexible and conductive waste tire-derived carbon/polymer composite paper as pseudocapacitive electrode

Science.gov (United States)

Naskar, Amit K.; Paranthaman, Mariappan Parans; Boota, Muhammad; Gogotsi, Yury

2018-04-10

A method of making a supercapacitor from waste tires, includes the steps of providing rubber pieces and contacting the rubber pieces with a sulfonation bath to produce sulfonated rubber; pyrolyzing the sulfonated rubber to produce a tire-derived carbon composite comprising carbon black embedded in rubber-derived carbon matrix comprising graphitized interface portions; activating the tire-derived carbon composite by contacting the tire-derived carbon composite with a specific surface area-increasing composition to increase the specific surface area of the carbon composite to provide an activated tire-derived carbon composite; and, mixing the activated tire-derived carbon composite with a monomer and polymerizing the monomer to produce a redox-active polymer coated, activated tire-derived carbon composite. The redox-active polymer coated, activated tire-derived carbon composite can be formed into a film. An electrode and a supercapacitor are also disclosed.

Evaluation of the energy consumption and climate comfort by means of a complete vehicle simulation; Energieverbrauchs- und Klimakomfortbewertung mittels Gesamtfahrzeugsimulation

Energy Technology Data Exchange (ETDEWEB)

Petr, Philipp [Technische Univ. Braunschweig (Germany). Inst. fuer Thermodynamik; Niedersaechsisches Forschungszentrum Fahrzeugtechnik (NFF), Braunschweig (Germany); Mustafa, Rashad [Technische Univ. Braunschweig (Germany). Inst. fuer Fahrzeugtechnik; Niedersaechsisches Forschungszentrum Fahrzeugtechnik (NFF), Braunschweig (Germany); Schulze, Mirko [Technische Univ. Braunschweig (Germany). Inst. fuer Verbrennungskraftmaschinen; Niedersaechsisches Forschungszentrum Fahrzeugtechnik (NFF), Braunschweig (Germany)

2012-11-01

Intelligent thermal management for vehicles can significantly reduce energy consumption and improve the climatic comfort. This paper describes an approach of how to analyse and evaluate vehicle thermal management techniques and their combination with different test cycles in a connected vehicle environment as examples. The focus will be particularly on the methodological approach. Based on the energetic analysis of the considered drivetrain topologies conclusions can be drawn about the complex thermal and dynamic relations. The analysis in turn is based on the results of the full vehicle simulation and refers to reference driving cycles and relevant environmental conditions. The energy flow analyses derived from the simulation are used in order to develop suitable thermal management techniques, to evaluate their potential and to integrate them in the vehicle. In addition to the influence of the measures the potential resulting from an intelligent combination of techniques and their control strategies are identified. The energy consumption advantage as well as the improved heating of the passenger compartment - especially at low ambient temperatures - will be evaluated. (orig.)

Feasibility of Energy Harvesting Using a Piezoelectric Tire

Science.gov (United States)

Malotte, Christopher

While the piezoelectric effect has been around for some time, it has only recently caught interest as a potential sustainable energy harvesting device. Piezoelectric energy harvesting has been developed for shoes and panels, but has yet to be integrated into a marketable bicycle tire. For this thesis, the development and feasibility of a piezoelectric tire was done. This includes the development of a circuit that incorporates piezoceramic elements, energy harvesting circuitry, and an energy storage device. A single phase circuit was designed using an ac-dc diode rectifier. An electrolytic capacitor was used as the energy storage device. A financial feasibility was also done to determine targets for manufacturing cost and sales price. These models take into account market trends for high performance tires, economies of scale, and the possibility of government subsidies. This research will help understand the potential for the marketability of a piezoelectric energy harvesting tire that can create electricity for remote use. This study found that there are many obstacles that must be addressed before a piezoelectric tire can be marketed to the general public. The power output of this device is minuscule compared to an alkaline battery. In order for this device to approach the power output of an alkaline battery the weight of the device would also become an issue. Additionally this device is very costly compared to the average bicycle tire. Lastly, this device is extreme fragile and easily broken. In order for this device to become marketable the issues of power output, cost, weight, and durability must all be successfully overcome.

The influence of the tire inflation on pull properties of agriculture tractors

Directory of Open Access Journals (Sweden)

Jakub Katrenčík

2013-01-01

Full Text Available Agricultural tractors are robust and versatile machines, which must comply with the basic requirements of users under various conditions. The main requirements include economical and reliable operation and high performance. Fuel economy could be improved using multiple methods, for example a well trained operator, adequate farming conditions and optimal tire inflation. Tractor tires transmit engine power to the surface and as such they are crucial to tractor operation. In the first part of the field measurement, all tires were inflated to 180kPa, while in the second part of the field measurements the tire pressure was set to 75kPa in front tires and to 65 kPa in rear tires. The results of the field measurement of the John Deere 6920S tractor with different tire inflation shows that pull performance increased by 9.9% and wheel slip decreased by 9.7%.

Vibration Analysis of a Tire in Ground Contact under Varied Conditions

OpenAIRE

Karakus Murat; Cavus Aydin; Colakoglu Mehmet

2017-01-01

The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13) has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different...

Full-scale aicraft tire pressure tests

OpenAIRE

FABRE, C; BALAY, Jean Maurice; LERAT, P; MAZARS, A

2009-01-01

This paper describes an outdoor full-scale test planned to improve experimental and theoretical knowledge related to the effects of aircraft internal tire inflation pressure on the behavior and damage of flexible pavement. Since modern aircraft can have tire pressures greater than 15 bar, the tests focus on pressures from 15 to 17.5 bar. The experimental pavement located on the Toulouse-Blagnac airport in France will include up to seven al different test sections, representative of current ai...

Enhanced friction modeling for steady-state rolling tires

NARCIS (Netherlands)

Steen, van der R.

2010-01-01

Tire modeling is nowadays a necessary tool in the tire industry. Car manufacturers, governments and consumers demand better traction under all circumstances, less wear and more recently less noise and a lower rolling resistance. Therefore finite element analysis is adopted in the design process of

Tire Shred Backfill in Mechanically Stabilized Earth Wall Applications

OpenAIRE

Balunaini, Umashankar; Yoon, Sungmin; Prezzi, Monica; Salgado, Rodrigo

2009-01-01

Tire shred-soil mixture backfill for use in mechanically stabilized earth (MSE) walls has several advantages over traditional backfill materials: 1) good drainage, 2) high shear strength, 3) low compacted unit weight and 4) low lateral pressure exerted on retaining structures. This work presents the results of laboratory tests performed on tire shred-sand mixtures focusing on determining the properties required for their use as backfill in MSE wall applications. Three sizes of tire shreds are...

Advantage of SBR/carbon black masterbatch for tire tread application

Energy Technology Data Exchange (ETDEWEB)

Sone, K.; Ishiguro, M.; Akimoto, H.; Ishida, M.

1992-04-01

The performance required of tire tread is becoming more severe and more various year by year, as social demands on tires have been changing. To improve wear resistance, driving safety and good drive feeling, new HP tires (high performance passenger car tires) are developed intensively. In addition, good fuel efficiency is required to satisfy the CAFE rule, which was proposed for a better global environment. To support this movement of the tire industry, material suppliers are making an effort to supply better materials. Mitsubishi Kasei has been improving the quality and production process of WMB, a SBR/carbon black master-batch produced by co-coagulation of SBR latex, carbon black and extender oil under the wet dispersion process. Compared to the tire tread made from dry-mixing compounds, that made from the WMB shows the following characteristics: (1) the abrasion resistance and the durability are higher; (2) from the viscoelastic properties, skid performance and driving stability are expected to be improved. These characteristics are remarkable when WMB is compounded in the recipes for HP and racing tires using fine carbon black. In this article, these features of WMB are studied from the view point of carbon black dispersion and polymer-carbon black interaction. Furthermore, the changes of carbon black structure during abrasion and fatigue process are analyzed and the mechanisms of these processes are discussed.

Predicting the compressibility behaviour of tire shred samples for landfill applications.

Science.gov (United States)

Warith, M A; Rao, Sudhakar M

2006-01-01

Tire shreds have been used as an alternative to crushed stones (gravel) as drainage media in landfill leachate collection systems. The highly compressible nature of tire shreds (25-47% axial strain on vertical stress applications of 20-700 kPa) may reduce the thickness of the tire shred drainage layer to less than 300 mm (minimum design requirement) during the life of the municipal solid waste landfill. There hence exists a need to predict axial strains of tire shred samples in response to vertical stress applications so that the initial thickness of the tire shred drainage layer can be corrected for compression. The present study performs one-dimensional compressibility tests on four tire shred samples and compares the results with stress/strain curves from other studies. The stress/strain curves are developed into charts for choosing the correct initial thickness of tire shred layers that maintain the minimum thickness of 300 mm throughout the life of the landfill. The charts are developed for a range of vertical stresses based on the design height of municipal waste cell and bulk unit weight of municipal waste. Experimental results also showed that despite experiencing large axial strains, the average permeability of the tire shred sample consistently remained two to three orders of magnitude higher than the design performance criterion of 0.01cm/s for landfill drainage layers. Laboratory experiments, however, need to verify whether long-term chemical and bio-chemical reactions between landfill leachate and the tire shred layer will deteriorate their mechanical functions (hydraulic conductivity, compressibility, strength) beyond permissible limits for geotechnical applications.

A systematic experimental investigation of significant parameters affecting model tire hydroplaning

Science.gov (United States)

Wray, G. A.; Ehrlich, I. R.

1973-01-01

The results of a comprehensive parametric study of model and small pneumatic tires operating on a wet surface are presented. Hydroplaning inception (spin down) and rolling restoration (spin up) are discussed. Conclusions indicate that hydroplaning inception occurs at a speed significantly higher than the rolling restoration speed. Hydroplaning speed increases considerably with tread depth, surface roughness and tire inflation pressure of footprint pressure, and only moderately with increased load. Water film thickness affects spin down speed only slightly. Spin down speed varies inversely as approximately the one-sixth power of film thickness. Empirical equations relating tire inflation pressure, normal load, tire diameter and water film thickness have been generated for various tire tread and surface configurations.

Influence of different processing techniques on the mechanical properties of used tires in embankment construction

International Nuclear Information System (INIS)

Edincliler, Ayse; Baykal, Goekhan; Saygili, Altug

2010-01-01

Use of the processed used tires in embankment construction is becoming an accepted way of beneficially recycling scrap tires due to shortages of natural mineral resources and increasing waste disposal costs. Using these used tires in construction requires an awareness of the properties and the limitations associated with their use. The main objective of this paper is to assess the different processing techniques on the mechanical properties of used tires-sand mixtures to improve the engineering properties of the available soil. In the first part, a literature study on the mechanical properties of the processed used tires such as tire shreds, tire chips, tire buffings and their mixtures with sand are summarized. In the second part, large-scale direct shear tests are performed to evaluate shear strength of tire crumb-sand mixtures where information is not readily available in the literature. The test results with tire crumb were compared with the other processed used tire-sand mixtures. Sand-used tire mixtures have higher shear strength than that of the sand alone and the shear strength parameters depend on the processing conditions of used tires. Three factors are found to significantly affect the mechanical properties: normal stress, processing techniques, and the used tire content.

Influence of different processing techniques on the mechanical properties of used tires in embankment construction.

Science.gov (United States)

Edinçliler, Ayşe; Baykal, Gökhan; Saygili, Altug

2010-06-01

Use of the processed used tires in embankment construction is becoming an accepted way of beneficially recycling scrap tires due to shortages of natural mineral resources and increasing waste disposal costs. Using these used tires in construction requires an awareness of the properties and the limitations associated with their use. The main objective of this paper is to assess the different processing techniques on the mechanical properties of used tires-sand mixtures to improve the engineering properties of the available soil. In the first part, a literature study on the mechanical properties of the processed used tires such as tire shreds, tire chips, tire buffings and their mixtures with sand are summarized. In the second part, large-scale direct shear tests are performed to evaluate shear strength of tire crumb-sand mixtures where information is not readily available in the literature. The test results with tire crumb were compared with the other processed used tire-sand mixtures. Sand-used tire mixtures have higher shear strength than that of the sand alone and the shear strength parameters depend on the processing conditions of used tires. Three factors are found to significantly affect the mechanical properties: normal stress, processing techniques, and the used tire content. Copyright 2009. Published by Elsevier Ltd.

Upgrading pyrolytic residue from waste tires to commercial carbon black.

Science.gov (United States)

Zhang, Xue; Li, Hengxiang; Cao, Qing; Jin, Li'e; Wang, Fumeng

2018-05-01

The managing and recycling of waste tires has become a worldwide environmental challenge. Among the different disposal methods for waste tires, pyrolysis is regarded as a promising route. How to effectively enhance the added value of pyrolytic residue (PR) from waste tires is a matter of great concern. In this study, the PRs were treated with hydrochloric and hydrofluoric acids in turn under ultrasonic waves. The removal efficiency for the ash and sulfur was investigated. The pyrolytic carbon black (PCB) obtained after treating PR with acids was analyzed by X-ray fluorescence spectrophotometry, Fourier transform infrared spectrometry, X-ray diffractometry, laser Raman spectrometry, scanning electron microscopy, thermogravimetric (TG) analysis, and physisorption apparatus. The properties of PCB were compared with those of commercial carbon black (CCB) N326 and N339. Results showed PRs from waste tires were mainly composed of carbon, sulfur, and ash. The carbon in PCB was mainly from the CCB added during tire manufacture rather than from the pyrolysis of pure rubbers. The removal percentages for the ash and sulfur of PR are 98.33% (from 13.98 wt % down to 0.24 wt %) and 70.16% (from 1.81 wt % down to 0.54 wt %), respectively, in the entire process. The ash was mainly composed of metal oxides, sulfides, and silica. The surface properties, porosity, and morphology of the PCB were all close to those of N326. Therefore, PCB will be a potential alternative of N326 and reused in tire manufacture. This route successfully upgrades PR from waste tires to the high value-added CCB and greatly increases the overall efficiency of the waste tire pyrolysis industry.

The design and improvement of radial tire molding machine

Science.gov (United States)

Wang, Wenhao; Zhang, Tao

2018-04-01

This paper presented that the high accuracy semisteel meridian tire molding machine structure configurations, combining tyre high precision characteristics, the original structure and parameter optimization, technology improvement innovation design period of opening and closing machine rotary shaping drum institutions. This way out of the shaft from the structure to the push-pull type movable shaping drum of thinking limit, compared with the specifications and shaping drum can smaller contraction, is conducive to forming the tire and reduce the tire deformation.

Performance of Used Tire Cushion Layer under Rockfall Impact

OpenAIRE

Sun, Jianhu; Chu, Zhaojun; Liu, Yingfang; Luo, Weiming; Wang, Min

2016-01-01

Rock shed is widely used in traffic lines against rockfall. In order to cushion rockfall impact and dissipate impact energy, cushion layer is usually adopted in rock shed. Used tire cushion layer is proposed in this paper and it can cushion rockfall impact utilizing large radial deformation of tire. Reinforced concrete structure model is built with used tire cushion layer and artificial rockfall test is carried out. Twelve tests are divided into 4 sets with different rockfall mass, rockfall h...

Impacts of Providing Inertial Response on Dynamic Loads of Wind Turbine Drivetrains: Preprint

Energy Technology Data Exchange (ETDEWEB)

Girsang, I. P.; Dhupia, J.; Singh, M.; Gevorgian, V.; Muljadi, E.; Jonkman, J.

2014-09-01

There has been growing demand from the power industry for wind power plants to support power system operations. One such requirement is for wind turbines to provide ancillary services in the form of inertial response. When the grid frequency drops, it is essential for wind turbine generators (WTGs) to inject kinetic energy stored in their inertia into the grid to help arrest the frequency decline. However, the impacts of inertial response on the structural loads of the wind turbine have not been given much attention. To bridge this gap, this paper utilizes a holistic model for both fixed-speed and variable-speed WTGs by integrating the aeroelastic wind turbine model in FAST, developed by the National Renewable Energy Laboratory, with the electromechanical drivetrain model in SimDriveline and SimPowerSystems.

Design of driving control strategy of torque distribution for two - wheel independent drive electric vehicle

Science.gov (United States)

Zhang, Chuanwei; Zhang, Dongsheng; Wen, Jianping

2018-02-01

In order to coordinately control the torque distribution of existing two-wheel independent drive electric vehicle, and improve the energy efficiency and control stability of the whole vehicle, the control strategies based on fuzzy control were designed which adopt the direct yaw moment control as the main line. For realizing the torque coordination simulation of the two-wheel independent drive vehicle, the vehicle model, motor model and tire model were built, including the vehicle 7 - DOF dynamics model, motion equation, torque equation. Finally, in the Carsim - Simulink joint simulation platform, the feasibility of the drive control strategy was verified.

Geotechnical Investigation of the Potential Use of Shredded Scrap Tires in Soil Stabilization.

Science.gov (United States)

1998-11-01

Silt-tire and clay-tire mixtures, containing 0% to 100% shredded tire material by weight, with tire chips ranging in size from 7mm-13mm, 13mm-25mm, and 25mm-38mm, were tested for a series of engineering properties including compaction characteristics...

Full-scale aircraft tire pressure tests

OpenAIRE

FABRE, C; BALAY, Jean Maurice; LERAT, P; MAZARS, A

2009-01-01

This paper describes an outdoor full-scale test planned to improve experimental and theoretical knowledge related to the effects of aircraft internal tire inflation pressure on the behavior and damage of flexible pavement. Since modern aircraft can have tire pressures greater than 15 bar, the tests will focus on pressures from 15 bar to 17.5 bar. The experimental pavement located on the Toulouse-Blagnac airport in France will include up to seven al different test sections, representative of c...

14 CFR 29.475 - Tires and shock absorbers.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires and shock absorbers. 29.475 Section 29.475 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Strength Requirements Ground Loads § 29.475 Tires and shock absorbers. Unless otherwise...

Oxidative desulfurization of tire pyrolysis oil

Directory of Open Access Journals (Sweden)

Ahmad Shahzad

2016-01-01

Full Text Available This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure and 50°C temperature for comparison of performance of various additives. The use of hydrogen peroxide-acetic acid mixture (10 wt.% was found more economical and effective in desulfurization and improvement of fuel properties of sample oils. The contribution of sulfuric acid in desulfurization and decreasing viscosity was also satisfactory but due to high price of concentrated sulfuric acid its use may not be economical. Calcium oxide and Fuller’s earth was not found to be effective in desulfurization. Results indicate that oxidative desulfurization could render tire pyrolysis oils suitable for blending as heating fuel.

No immediate relief for large mining tire shortage

Energy Technology Data Exchange (ETDEWEB)

Fiscor, S.

2006-05-15

Inventories are low and they will not get better anytime soon, but mine operators do have a few options. The three main manufacturers supplying tires to the US mining industry, Bridgestone Firestone Off Road Tire Company, Goodyear and Michelin are struggling to keep up with demand, but are unlikely to restore inventories to manageable levels by 2009. Meanwhile Yokohama and Global Tyres have stepped in to help. The article reports plans for expansions to plant in Japan. In the meantime, mine operators need to plan accordingly and pay increased attention to tire maintenance. The larger the tyre, the less available it is. 3 photos.

Regenerative Braking Control Strategy of Electric-Hydraulic Hybrid (EHH Vehicle

Directory of Open Access Journals (Sweden)

Yang Yang

2017-07-01

Full Text Available A novel electric-hydraulic hybrid drivetrain incorporating a set of hydraulic systems is proposed for application in a pure electric vehicle. Models of the electric and hydraulic components are constructed. Two control strategies, which are based on two separate rules, are developed; the maximum energy recovery rate strategy adheres to the rule of the maximization of the braking energy recovery rate, while the minimum current impact strategy adheres to the rule of the minimization of the charge current to the battery. The simulation models were established to verify the effects of these two control strategies. An ABS (Anti-lock Braking System fuzzy control strategy is also developed and simulated. The simulation results demonstrate that the developed control strategy can effectively absorb the braking energy, suppress the current impact, and assure braking safety.

A study on the fatigue life prediction of tire belt-layers using probabilistic method

International Nuclear Information System (INIS)

Lee, Dong Woo; Park, Jong Sang; Lee, Tae Won; Kim, Seong Rae; Sung, Ki Deug; Huh, Sun Chul

2013-01-01

Tire belt separation failure is occurred by internal cracks generated in *1 and *2 belt layers and by its growth. And belt failure seriously affects tire endurance. Therefore, to improve the tire endurance, it is necessary to analyze tire crack growth behavior and predict fatigue life. Generally, the prediction of tire endurance is performed by the experimental method using tire test machine. But it takes much cost and time to perform experiment. In this paper, to predict tire fatigue life, we applied deterministic fracture mechanics approach, based on finite element analysis. Also, probabilistic analysis method based on statistics using Monte Carlo simulation is presented. Above mentioned two methods include a global-local finite element analysis to provide the detail necessary to model explicitly an internal crack and calculate the J-integral for tire life prediction.

14 CFR 27.475 - Tires and shock absorbers.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires and shock absorbers. 27.475 Section 27.475 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Strength Requirements Ground Loads § 27.475 Tires and shock absorbers. Unless otherwise prescribed...

The experimental assessment of dynamic tire handling performance

NARCIS (Netherlands)

Pauwelussen, J.P.

1999-01-01

Testing of steady state tire handling performance is nowadays common practice with slip angle sweeps and breaking being simulated in the laboratory with drum or flat belt, or on the road with a test trailer. In recent years, more emphasis is put on dynamic tire models, motivated by ride comfort

Vehicle Sideslip Angle Estimation Based on Hybrid Kalman Filter

Directory of Open Access Journals (Sweden)

Jing Li

2016-01-01

Full Text Available Vehicle sideslip angle is essential for active safety control systems. This paper presents a new hybrid Kalman filter to estimate vehicle sideslip angle based on the 3-DoF nonlinear vehicle dynamic model combined with Magic Formula tire model. The hybrid Kalman filter is realized by combining square-root cubature Kalman filter (SCKF, which has quick convergence and numerical stability, with square-root cubature based receding horizon Kalman FIR filter (SCRHKF, which has robustness against model uncertainty and temporary noise. Moreover, SCKF and SCRHKF work in parallel, and the estimation outputs of two filters are merged by interacting multiple model (IMM approach. Experimental results show the accuracy and robustness of the hybrid Kalman filter.

Measurement of whole tire profile

Science.gov (United States)

Yang, Yongyue; Jiao, Wenguang

2010-08-01

In this paper, a precision measuring device is developed for obtaining characteristic curve of tire profile and its geometric parameters. It consists of a laser displacement measurement unit, a closed-loop precision two-dimensional coordinate table, a step motor control system and a fast data acquisition and analysis system. Based on the laser trigonometry, a data map of tire profile and coordinate values of all points can be obtained through corresponding data transformation. This device has a compact structure, a convenient control, a simple hardware circuit design and a high measurement precision. Experimental results indicate that measurement precision can meet the customer accuracy requirement of +/-0.02 mm.

Preventing Tire Blowout Accidents: A Perspective on Factors Affecting Drivers’ Intention to Adopt Tire Pressure Monitoring System

Directory of Open Access Journals (Sweden)

Kai-Ying Chen

2018-04-01

Full Text Available The aim of this study is to explore whether risk perception or anticipated regret is responsible for intensifying the participants’ intention to adopt a tire pressure monitoring system (TPMS to prevent a tire-related accident, and whether the optimism bias has a moderator effect between risk perception/anticipated regret and intention. With 274 valid questionnaires and PLS-SEM (partial least squares structural equation modeling analysis, the results indicate a significant positive relationship between risk perception and intention to adopt TPMS, but not between anticipated regret and intention. The moderator effect of optimism bias on risk perception and anticipated regret is not found in the model. The findings will prove useful for public service advertising campaigns by providing a basis for an understanding of the role of cognitive and emotional factors in tire-blowout accident prevention, thereby increasing the motivation for drivers in Taiwan to take advantage of the protection afforded them by using TPMS.

Recycled tires as coarse aggregate in concrete pavement mixtures.

Science.gov (United States)

2013-07-01

The reuse potential of tire chips as coarse aggregates in pavement concrete was examined in this research by : investigating the effects of low- and high-volume tire chips on fresh and hardened concrete properties. One concrete : control mixture was ...

Utilization of waste tire rubber in manufacture of oriented strandboard.

Science.gov (United States)

Ayrilmis, Nadir; Buyuksari, Umit; Avci, Erkan

2009-09-01

Some physical and mechanical properties of oriented strandboards (OSBs) containing waste tire rubber at various addition levels based on the oven-dry strand weight, using the same method as that used in the manufacture of OSB. Two resin types, phenol-formaldehyde (PF) and polyisocyanate, were used in the experiments. The manufacturing parameters were: a specific gravity of 0.65 and waste tire rubber content (10/90, 20/80 and 30/70 by wt.% of waste tire rubber/wood strand). Average internal bond values of PF-bonded OSB panels with rubber chips were between 17.6% and 48.5% lower than the average of the control samples while polyisocyanate bonded OSBs were 16.5-50.6%. However, water resistance and mechanical properties of OSBs made using polyisocyanate resin were found to comply with general-purpose OSB minimum property requirements of EN 300 Type 1 (1997) values for use in dry conditions at the lowest tire rubber loading level (10%) based on the oven-dry panel weight. The tire rubber improved water resistance of the OSB panel due to its almost hydrophobic property. Based on the findings obtained from this study, we concluded that waste tire rubber could be used for general-purpose OSB manufacturing up to 10% ratio based on the oven-dry panel weight.

Neutron vibrational spectroscopic studies of novel tire-derived carbon materials.

Science.gov (United States)

Li, Yunchao; Cheng, Yongqiang; Daemen, Luke L; Veith, Gabriel M; Levine, Alan M; Lee, Richard J; Mahurin, Shannon M; Dai, Sheng; Naskar, Amit K; Paranthaman, Mariappan Parans

2017-08-23

Sulfonated tire-derived carbons have been demonstrated to be high value-added carbon products of tire recycling in several energy storage system applications including lithium, sodium, potassium ion batteries and supercapacitors. In this communication, we compared different temperature pyrolyzed sulfonated tire-derived carbons with commercial graphite and unmodified/non-functionalized tire-derived carbon by studying the surface chemistry and properties, vibrational spectroscopy of the molecular structure, chemical bonding such as C-H bonding, and intermolecular interactions of the carbon materials. The nitrogen adsorption-desorption studies revealed the tailored micro and meso pore size distribution of the carbon during the sulfonation process. XPS and neutron vibrational spectra showed that the sulfonation of the initial raw tire powders could remove the aliphatic hydrogen containing groups ([double bond splayed left]CH 2 and -CH 3 groups) and reduce the number of heteroatoms that connect to carbon. The absence of these functional groups could effectively improve the first cycle efficiency of the material in rechargeable batteries. Meanwhile, the introduced -SO 3 H functional group helped in producing terminal H at the edge of the sp 2 bonded graphite-like layers. This study reveals the influence of the sulfonation process on the recovered hard carbon from used tires and provides a pathway to develop and improve advanced energy storage materials.

Dual extended Kalman filter for combined estimation of vehicle state and road friction

Science.gov (United States)

Zong, Changfu; Hu, Dan; Zheng, Hongyu

2013-03-01

Vehicle state and tire-road adhesion are of great use and importance to vehicle active safety control systems. However, it is always not easy to obtain the information with high accuracy and low expense. Recently, many estimation methods have been put forward to solve such problems, in which Kalman filter becomes one of the most popular techniques. Nevertheless, the use of complicated model always leads to poor real-time estimation while the role of road friction coefficient is often ignored. For the purpose of enhancing the real time performance of the algorithm and pursuing precise estimation of vehicle states, a model-based estimator is proposed to conduct combined estimation of vehicle states and road friction coefficients. The estimator is designed based on a three-DOF vehicle model coupled with the Highway Safety Research Institute(HSRI) tire model; the dual extended Kalman filter (DEKF) technique is employed, which can be regarded as two extended Kalman filters operating and communicating simultaneously. Effectiveness of the estimation is firstly examined by comparing the outputs of the estimator with the responses of the vehicle model in CarSim under three typical road adhesion conditions(high-friction, low-friction, and joint-friction). On this basis, driving simulator experiments are carried out to further investigate the practical application of the estimator. Numerical results from CarSim and driving simulator both demonstrate that the estimator designed is capable of estimating the vehicle states and road friction coefficient with reasonable accuracy. The DEKF-based estimator proposed provides the essential information for the vehicle active control system with low expense and decent precision, and offers the possibility of real car application in future.

Sustainable Transportation: Accelerating Widespread Adoption of Energy Efficient Vehicles & Fuels (Brochure)

Energy Technology Data Exchange (ETDEWEB)

2014-12-01

While energy efficient transportation strategies have the potential to simultaneously slash oil consumption and reduce greenhouse gas (GHG) emissions, a truly sustainable solution will require more than just putting drivers behind the wheels of new fuel-efficient cars. As the only national laboratory dedicated 100% to renewable energy and energy efficiency, the National Renewable Energy Laboratory (NREL) accelerates widespread adoption of high-performance, low-emission, energy-efficient passenger and freight vehicles, as well as alternative fuels and related infrastructure. Researchers collaborate closely with industry, government, and research partners, using a whole-systems approach to design better batteries, drivetrains, and engines, as well as thermal management, energy storage, power electronic, climate control, alternative fuel, combustion, and emission systems. NREL's sustainable transportation research, development, and deployment (RD&D) efforts are not limited to vehicles, roads, and fueling stations. The lab also explores ways to save energy and reduce GHGs by integrating transportation technology advancements with renewable energy generation, power grids and building systems, urban planning and policy, and fleet operations.

Experimental and numerical study of friction and braking characteristics of rolling tires

NARCIS (Netherlands)

Steen, R. van der; Lopez, I.; Nijmeijer, H.; Schmeitz, A.J.C.; Bruijn, B. de

2011-01-01

Throughout the tire industry, virtual testing has been widely adopted in the design process. Both static deformation and dynamic response of the tire rolling on the road must be accurately predicted to evaluate the handling performance of a tire. Unfortunately, experimental characterization of

Federal Research Action Plan on Recycled Tire Crumb Used ...

Science.gov (United States)

Over the past several years, parents, athletes, schools, and communities have raised concerns about the safety of recycled tire crumb rubber used as infill for playing fields and playgrounds in the United States. The public has expressed concerns that the use of these fields could potentially be related to certain health effects. Studies to date have not shown an elevated health risk from playing on fields with tire crumb rubber, but these studies have limitations and do not comprehensively evaluate the concerns about health risks from exposure to tire crumb rubber. This status report provides a summary of activities to date, including: (1) stakeholder outreach, (2) the tire crumb rubber manufacturing industry, (3) the final peer-reviewed Literature Review/Gaps Analysis (LRGA), (4) progress on the research activities, and (5) next steps and a timeline for completion of the final report. The status report does not include research findings.

Construction of a test embankment using a sand-tire shred mixture as fill material.

Science.gov (United States)

Yoon, Sungmin; Prezzi, Monica; Siddiki, Nayyar Zia; Kim, Bumjoo

2006-01-01

Use of tire shreds in construction projects, such as highway embankments, is becoming an accepted way of beneficially recycling scrap tires. However, in the last decade there was a decline in the use of pure tire shreds as fill materials in embankment construction, as they are susceptible to fire hazards due to the development of exothermic reactions. Tire shred-sand mixtures, on the other hand, were found to be effective in inhibiting exothermic reactions. When compared with pure tire shreds, tire shred-sand mixtures are less compressible and have higher shear strength. However, the literature contains limited information on the use of tire shred-soil mixtures as a fill material. The objectives of this paper are to discuss and evaluate the feasibility of using tire shred-sand mixtures as a fill material in embankment construction. A test embankment constructed using a 50/50 mixture, by volume, of tire shreds and sand was instrumented and monitored to: (a) determine total and differential settlements; (b) evaluate the environmental impact of the embankment construction on the groundwater quality due to leaching of fill material; and (c) study the temperature variation inside the embankment. The findings in this research indicate that mixtures of tire shreds and sand are viable materials for embankment construction.

Experimental Investigations on the Pull-Out Behavior of Tire Strips Reinforced Sands.

Science.gov (United States)

Li, Li-Hua; Chen, Yan-Jun; Ferreira, Pedro Miguel Vaz; Liu, Yong; Xiao, Heng-Lin

2017-06-27

Waste tires have excellent mechanical performance and have been used as reinforcing material in geotechnical engineering; however, their interface properties are poorly understood. To further our knowledge, this paper examines the pull-out characteristics of waste tire strips in a compacted sand, together with uniaxial and biaxial geogrids also tested under the same conditions. The analysis of the results shows that the interlocking effect and pull-out resistance between the tire strip and the sand is very strong and significantly higher than that of the geogrids. In the early stages of the pull-out test, the resistance is mainly provided by the front portion of the embedded tire strips, as the pull-out test continues, more and more of the areas towards the end of the tire strips are mobilized, showing a progressive failure mechanism. The deformations are proportional to the frictional resistance between the tire-sand interface, and increase as the normal stresses increase. Tire strips of different wear intensities were tested and presented different pull-out resistances; however, the pull-out resistance mobilization patterns were generally similar. The pull-out resistance values obtained show that rubber reinforcement can provide much higher pull-out forces than the geogrid reinforcements tested here, showing that waste tires are an excellent alternative as a reinforcing system, regardless of the environmental advantages.

Study on Differential Regenerative Braking Torque Control to Increase the Stability of the Small Electric Vehicle with Four In-Wheel Motors

Directory of Open Access Journals (Sweden)

Ali N. M.

2017-01-01

Full Text Available Based on the advantages of the electric motor such as fast and precise torque response, the performance of the electric vehicle (EV can be improved. During braking or driving on the cornering, the vehicle will over steer or under steer if a car turns by more or less than the amount commanded by the driver. To improve the stability of the small EV with four in-wheel motors, the differential regenerative braking torque control is proposed. In this system, the regenerative braking torque at each wheel will be controlled individually based on the value of slip ratio. If the slip ratio is greater than the optimum value, the regenerative brake will turn off. In this situation, the electric motor will not produce the regenerative braking torque. Conversely, if the slip ratio lower than the optimum value, the regenerative brake will turn on and the electric motor will generate the regenerative braking torque. In the numerical analysis, to investigate the effectiveness of the proposed model, the road condition is set to an icy road on the left tire and dry asphalt on the right tire. From the simulation results, the differential regenerative braking torque control can prevent the tire from lock-up and avoid the vehicle from skidding.

Transient tire force and its modeling. Part 2. Camber angle input; Katoteki tire hasseiryoku to sono modeling. 2. Camber kaku nyuryoku

Energy Technology Data Exchange (ETDEWEB)

Higuchi, A [Toyota Motor Corp., Aichi (Japan); Pacejka, H

1997-10-01

The objective of this study is to understand the transient force and moment characteristics of tires involving side slip and camber and to develop the tire model which is capable of describing those characteristics. Some particular characteristics are found such as non-lagging part in side force response and an apparent peak in aligning torque response to a stepwise camber change. Some aspects on the analogy of turn slip to camber are also discussed. The tire model combines a dynamic part based on the physical aspect using the relaxation length concept, and a steady state part. In combined situations of side slip and camber, an estimation method to determine the transient slip quantities is introduced. 12 refs., 14 figs.

Effect of Tire Pressure to Physical Workload at Operating a Manual Wheelchair.

Science.gov (United States)

Booka, Masayuki; Yoneda, Ikuo; Hashizume, Tsutomu; Lee, Hokyoo; Oku, Hidehisa; Fujisawa, Shoichiro

2015-01-01

It is often experienced that low tire pressure of the wheelchair not only increases running resistance, but also reduces parking brake performance. In this study, the required driving forces for different tire pressures were experimentally measured and evaluated. It was indicated from the result that the wheelchair with proper tire pressure could be run with less workload of wheelchair-user. Then it was also indicated that the wheelchair with a lower tire pressure needed more workload of wheelchair-user even on hard level surface.

Uncontacted tire explosion causing trauma to bilateral lower extremities: A case report.

Science.gov (United States)

Yu, Ming-Yang; Su, Yun; Meng, Xiang-Jun; Luan, Bo-Wu; Gu, Gui-Shan; Sun, Qiang; Zhao, De-Wei

2017-06-01

It is uncommon for tire explosion related injuries on the lower extremity. The bilateral lower extremities were injured by tire explosion when the patient was seated in a bus. She sustained an open fracture with partial bone loss in the right calcaneus (a comminuted fracture in the right ankle joint) and a closed comminuted fracture in the left tibia and fibula. This damage was caused by uncontacted tire explosion, thanks to a thick floor between the exploded tire and the patient's feet. This type of injury on lower extremity caused by uncontacted tire explosion was uncommon. Copyright © 2017 Daping Hospital and the Research Institute of Surgery of the Third Military Medical University. Production and hosting by Elsevier B.V. All rights reserved.

Pavement system with rubber tire chips in subgrade

Energy Technology Data Exchange (ETDEWEB)

Ashtakala, B.; Hoque, A.K.M.M. [Concordia Univ., Montreal, PQ (Canada). Dept. of Civil Engineering

1995-12-31

A pavement design method was developed in which shredded rubber tire chips mixed with sand were used as a material for pavement subgrade. Rubber tire chips are highly compressible and produce both elastic and plastic deformations under the application of loads. Sand was added to fill the void between the tire chips and make the mixture a strong material. The design method considered the vertical compressive strain produced by the design life traffic load 18k (80 KN) repetitions. The equivalent thicknesses of the layers above the subgrade corresponding to this vertical compressive strain were determined using contour charts. From this equivalent thickness, the thicknesses for asphalt pavement, base, and sub-base were determined by Odemark`s method. 3 refs., 1 tab., 3 figs.

Voltage sag influence on fatigue life of the drivetrain of fixed speed wind turbines

DEFF Research Database (Denmark)

Veluri, Badrinath; Santos-Martin, David; Jensen, Henrik Myhre

2011-01-01

Occurrence of voltage sags due to electrical grid faults and other network disturbances generate transients of the generator electromagnetic torque which result in significant high stresses and noticeable vibrations for the wind turbine mechanical system and may also have a detrimental effect...... on the fatigue life of important drivetrain components. The high penetration of wind energy in the electrical grids demands new requirements for the operation of wind energy conversion systems. Although fixed speed wind turbine technology is nowadays replaced by variable speed wind turbines. In some countries...... by the stator flux oscillations which cause high transients of the generator electromagnetic torque. This paper focuses in estimating the resulting significant stresses transients due to the electromagnetic torque transients, which transmits to the wind turbine mechanical system that may have a detrimental...

EMC behaviour modelling and simulation of components of the electric drivetrain; EMV-Verhaltensmodellierung und Simulation von Komponenten des elektrischen Antriebsstrangs

Energy Technology Data Exchange (ETDEWEB)

Frei, Stephan; Kremer, Frank [Technische Univ. Dortmund (Germany). Arbeitsgebiet Bordsysteme; Haase, Joachim [Fraunhofer-Institut fuer Integrierte Schaltungen, Dresden (Germany). Bereich Entwurfsautomatisierung; Hessel, Ewald [Hella KGaA Hueck und Co, Lippstadt (Germany)

2013-03-15

The introduction of high-voltage on-board electrical systems and high pulsed electric power in the drivetrain tends to lead to higher levels of interference in electromagnetic compatibility (EMC), and managing this requires appropriate counter-measures to be taken. Research currently being carried out by TU Dortmund University, Hella and the Fraunhofer Institute for Integrated Circuits II S in Dresden is focusing on EMC-compliant function development. Modelling and simulation can help to identify potential problems at an early stage.

Measurement of airborne concentrations of tire and road wear particles in urban and rural areas of France, Japan, and the United States

Science.gov (United States)

Panko, Julie M.; Chu, Jennifer; Kreider, Marisa L.; Unice, Ken M.

2013-06-01

In addition to industrial facilities, fuel combustion, forest fires and dust erosion, exhaust and non-exhaust vehicle emissions are an important source of ambient air respirable particulate matter (PM10). Non-exhaust vehicle emissions are formed from wear particles of vehicle components such as brakes, clutches, chassis and tires. Although the non-exhaust particles are relatively minor contributors to the overall ambient air particulate load, reliable exposure estimates are few. In this study, a global sampling program was conducted to quantify tire and road wear particles (TRWP) in the ambient air in order to understand potential human exposures and the overall contribution of these particles to the PM10. The sampling was conducted in Europe, the United States and Japan and the sampling locations were selected to represent a variety of settings including both rural and urban core; and within each residential, commercial and recreational receptors. The air samples were analyzed using validated chemical markers for rubber polymer based on a pyrolysis technique. Results indicated that TRWP concentrations in the PM10 fraction were low with averages ranging from 0.05 to 0.70 μg m-3, representing an average PM10 contribution of 0.84%. The TRWP concentration in air was associated with traffic load and population density, but the trend was not statistically significant. Further, significant differences across days were not observed. This study provides a robust dataset to understand potential human exposures to airborne TRWP.

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks.

Science.gov (United States)

Sol-Sánchez, Miguel; Moreno-Navarro, Fernando; Rubio-Gámez, Mª Carmen

2014-08-18

Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats) to be used in railway tracks.

Aircraft and ground vehicle friction correlation test results obtained under winter runway conditions during joint FAA/NASA Runway Friction Program

Science.gov (United States)

Yager, Thomas J.; Vogler, William A.; Baldasare, Paul

1988-01-01

Aircraft and ground vehicle friction data collected during the Joint FAA/NASA Runway Friction Program under winter runway conditions are discussed and test results are summarized. The relationship between the different ground vehicle friction measurements obtained on compacted snow- and ice-covered conditions is defined together with the correlation to aircraft tire friction performance under similar runway conditions.

Development and applicability estimation of the tire contact pressure measurement system; Tire secchiatsukei no kaihatsu to oyosei hyoka

Energy Technology Data Exchange (ETDEWEB)

Mizutani, Y.; Amago, T.; Takahashi, T.; Sakuma, S.; Mori, N. [Toyota Central R and D Laboratories, Inc., Aichi (Japan); Nagae, A. [Toyota Motor Corp., Aichi (Japan); Yasuoka, M. [Toyo Tire and Rubber Co. Ltd., Osaka (Japan)

1995-04-20

A pressure sensor more reliable than the conventional types and a tire pressure measurement system using a plurality of sensors of the said reliable type have been developed. The sensor is an inverted T in shape, the upper surface of the vertical beam thereof receives the pressure, and the two ends of the horizontal beam are fixed. The load per unit area imposed on the pressure receiving surface is separated into three components, the X and Y components in the tangential direction are sensed by the vertical beam while the Z component in the vertical direction is sensed by a distortion gauge attached to the horizontal beam. For the measurement of the contact pressure distribution for the entire contact surface, a measuring device was developed, comprising a multiple point contact pressure gauge with 30 sensors of the reliable type discussed here embedded therein, a tire rolling tester, and a data processing unit. A tire wear estimation test was conducted using this pressure sensor and a contact probe type slip sensor, and it was found that a tire of a greater friction energy ratio is easier to experience abnormal abrasion and that the new pressure sensor is useful in estimating abnormal abrasion. Further, it was indicated that the present measuring device is applicable to the analysis of the mechanism wherein shaft force results from contact pressure on the soil. 3 refs., 11 figs., 3 tabs.

Efficacy of alpha-cypermethrin and lambda-cyhalothrin applications to prevent Aedes breeding in tires.

Science.gov (United States)

Pettit, William J; Whelan, Peter I; McDonnell, Joseph; Jacups, Susan P

2010-12-01

The efficacy of alpha-cypermethrin (Cyperthor) and lambda-cyhalothrin (Demand) to prevent mosquito larval colonization of water-containing receptacles was investigated using 2 differing applications in disused car tires in Darwin, Australia. Insecticide treatments were applied uniformly to the inside surfaces of 2 categories of tires: 1) dry tires that were partially filled with water 24 h after spraying and 2) wet tires partially filled with water prior to spraying. All mosquito larvae, pupae, and dead adults were collected from the treatment and control tires weekly over the 24-wk study period and were later identified to species in the laboratory. Control tires were colonized by Aedes notoscriptus in wk 2 and by Culex quinquefasciatus in wk 4. Aedes notoscriptus failed to colonize any alpha-cypermethrin-treated tires until wk 22 and did not colonize any lambda-cyhalothrin-treated tires during the 24-wk trial. Culex quinquefasciatus colonized alpha-cypermethrin and lambda-cyhalothrin-treated tires from wk 11 and wk 15, respectively. These results indicate both insecticides using either application method can prevent colonization of Ae. notoscriptus for at least 20 wk and demonstrate great potential for the prevention of breeding in receptacles for other receptacle-breeding Aedes species, such as the dengue vectors, Ae. aegypti and Ae. albopictus.

76 FR 12410 - BMW of North America, LLC, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2011-03-07

... certain BMW vehicles equipped with ``run- flat'' tires do not fully comply with paragraphs S4.3(c) and S4... 54,200 vehicles equipped with ``run flat'' tires are affected. The affected vehicle models are... the vehicles are equipped with ``run-flat'' tires and have no spare tire, the word ``none,'' as...

Strength and microstructure characteristics of the recycled rubber tire-sand mixtures as lightweight backfill.

Science.gov (United States)

Zhang, Tao; Cai, Guojun; Duan, Weihong

2018-02-01

The disposal of scrap rubber tires has induced critical environmental issue worldwide due to the rapid increase in the number of vehicles. Recycled scrap tires as a construction material in civil engineering have significant environmental benefits from a waste management perspective. A systematic study that deals with strength and microstructure characteristics of the rubber-sand mixtures is initiated, and mechanical response of the mixtures is discussed in this investigation. Experiments were conducted to evaluate the effects of rubber fraction on the basic properties including mass density (ρ), stress-strain characteristics, shear strength, and unconfined compression strength (q u ) of the rubber-sand mixtures. Additionally, scanning electron microscopy (SEM) was carried out to reveal the microstructure characteristics of the mixtures with various rubber fractions. A discussion on the micromechanics of the mixtures also was conducted. This study demonstrates that the ρ, friction angle, and q u decrease linearly with an increase in rubber fraction, whereas shear strain at peak increases. The stress-strain characteristics of the rubber-sand mixtures shift from brittle to ductile as the rubber fraction increase. These changes are attributed to remarkably lower stiffness and higher compressibility of the rubber particle compared with those of the conventional mineral aggregates. With an increase in the rubber fraction, the mechanical response of rubber-sand mixtures exhibits two types: sand-like material and rubber-like material. Rubber particle possesses the capacity to prevent the contacted sand particles from sliding at lower rubber fraction, whereas it transmits the applied loadings as the rubber fraction increased. This outcome reinforces the practicability of using recycled rubber tire-sand mixtures as a lightweight backfill in subbase/base applications.

77 FR 71679 - Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2012-12-03

... noncompliant tires are mislabeled; the subject tires meet or exceed all performance requirements as required in...-0108; Notice 1] Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of... petition. SUMMARY: Bridgestone Americas Tire Operations, LLC (BRIDGESTONE),\\1\\ has determined that certain...

78 FR 47050 - Cooper Tire & Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-08-02

..., and tread wear, temperature, and traction ratings to assess performance capabilities of various tires...-0109; Notice 2] Cooper Tire & Rubber Company, Grant of Petition for Decision of Inconsequential...: Cooper Tire & Rubber Company (Cooper) \\1\\ has determined that certain Cooper brand replacement tires...

Strength of mortar containing rubber tire particle

Science.gov (United States)

Jusoh, M. A.; Abdullah, S. R.; Adnan, S. H.

2018-04-01

The main focus in this investigation is to determine the strength consist compressive and tensile strength of mortar containing rubber tire particle. In fact, from the previous study, the strength of mortar containing waste rubber tire in mortar has a slightly decreases compare to normal mortar. In this study, rubber tire particle was replacing on volume of fine aggregate with 6%. 9% and 12%. The sample were indicated M0 (0%), M6 (6%), M9 (9%) and M12 (12%). In this study, two different size of sample used with cube 100mm x 100mm x 100mm for compressive strength and 40mm x 40mm x 160mm for flexural strength. Morphology test was conducted by using Scanning electron microscopic (SEM) were done after testing compressive strength test. The concrete sample were cured for day 3, 7 and 28 before testing. Results compressive strength and flexural strength of rubber mortar shown improved compare to normal mortar.

Chemi-microbial processing of waste tire rubber: A project overview

International Nuclear Information System (INIS)

Romine, R.A.; Snowden-Swan, L.

1993-12-01

PNL is developing a method to use thiophillic microorganisms to devulcanize (biodesulfurize) the surface of ground rubber particles, which will improve the bonding and adhesion of the ground tire rubber into the virgin tire rubber matrix. The Chemi-microbial processing approach, introduced in this paper, is targeted at alleviating the waste tire problem in an environmentally conscious manner; it may also be applied to improve asphaltic materials and rubber and polymeric wastes to facilite their recycling. This paper outlines the logic and technical methods that will be used

Federal Research on Recycled Tire Crumb Used on Playing Fields

Science.gov (United States)

Ground rubber is recovered from scrap tires or from the tire retreading process. It is used in road construction and in athletic and recreational applications,like ground cover under playground equipment, running track material, and as a soil additive.

78 FR 54369 - The Goodyear Tire & Rubber Company, Mootness of Petition for Decision of Inconsequential...

Science.gov (United States)

2013-09-03

... subject tires meet or exceed all applicable FMVSS performance standards for a tire labeled as either load...-0107; Notice 2] The Goodyear Tire & Rubber Company, Mootness of Petition for Decision of... Petition Mootness. SUMMARY: The Goodyear Tire & Rubber Company (Goodyear),\\1\\ has determined that certain...

78 FR 9775 - Cooper Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-02-11

... subject tires in fact have more tread plies than indicated and meet or exceed all performance requirements...-0109; Notice 1] Cooper Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential...: Cooper Tire & Rubber Company (Cooper),\\1\\ has determined that certain Cooper brand tires manufactured...

Extended-Kalman-filter-based regenerative and friction blended braking control for electric vehicle equipped with axle motor considering damping and elastic properties of electric powertrain

Science.gov (United States)

Lv, Chen; Zhang, Junzhi; Li, Yutong

2014-11-01

Because of the damping and elastic properties of an electrified powertrain, the regenerative brake of an electric vehicle (EV) is very different from a conventional friction brake with respect to the system dynamics. The flexibility of an electric drivetrain would have a negative effect on the blended brake control performance. In this study, models of the powertrain system of an electric car equipped with an axle motor are developed. Based on these models, the transfer characteristics of the motor torque in the driveline and its effect on blended braking control performance are analysed. To further enhance a vehicle's brake performance and energy efficiency, blended braking control algorithms with compensation for the powertrain flexibility are proposed using an extended Kalman filter. These algorithms are simulated under normal deceleration braking. The results show that the brake performance and blended braking control accuracy of the vehicle are significantly enhanced by the newly proposed algorithms.

Tire Production and Pollution Control. Environmental Education Curriculum. Revised.

Science.gov (United States)

Topeka Public Schools, KS.

This unit was developed to introduce secondary students to the many facets of a typical, large manufacturing plant - the Topeka Goodyear Tire and Rubber Company - in an effort to increase awareness of sound environmental practices in industry. Its five major foci include the production of tires and quality control procedures; applications of…

Numerical study of aerodynamic effects on road vehicles lifting surfaces

Science.gov (United States)

Cernat, Mihail Victor; Cernat Bobonea, Andreea

2017-01-01

The aerodynamic performance analysis of road vehicles depends on the study of engine intake and cooling flow, internal ventilation, tire cooling, and overall external flow as the motion of air around a moving vehicle affects all of its components in one form or another. Due to the complex geometry of these, the aerodynamic interaction between the various body components is significant, resulting in vortex flow and lifting surface shapes. The present study, however focuses on the effects of external aerodynamics only, and in particular on the flow over the lifting surfaces of a common compact car, designed especially for this study.

Dynamic motion stabilization for front-wheel drive in-wheel motor electric vehicles

Directory of Open Access Journals (Sweden)

Jia-Sheng Hu

2015-12-01

Full Text Available This article presents a new dynamic motion stabilization approach to front-wheel drive in-wheel motor electric vehicles. The approach includes functions such as traction control system, electronic differential system, and electronic stability control. The presented electric vehicle was endowed with anti-skid performance in longitudinal accelerated start; smooth turning with less tire scrubbing; and safe driving experience in two-dimensional steering. The analysis of the presented system is given in numerical derivations. For practical verifications, this article employed a hands-on electric vehicle named Corsa-electric vehicle to carry out the tests. The presented approach contains an integrated scheme which can achieve the mentioned functions in a single microprocessor. The experimental results demonstrated the effectiveness and feasibility of the presented methodology.

75 FR 17830 - Continental Tire North America, Inc., Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2010-04-07

... safety as it ``does not affect the safety, performance and durability of the tire; the tires were built... requirements. Continental said that it performs ongoing compliance testing ``to assure tire performance'' and that ``all tires included in this petition will meet or exceed the performance requirements of FMVSS...

The Implementation of Quality Function Deployment (QFD in Tire Industry

Directory of Open Access Journals (Sweden)

Hari Abdul Hadi

2017-12-01

Full Text Available This research had two main objectives. The first research objective was to make the right design of new product according to customer requirements with the implementation of Quality Function Deployment (QFD in the tire industry. The second research objective was to enhance competitiveness based on the renewal of marketing strategy and consumer needs, non-explosive prohibition, non-slip tires, no bulgy, and competitive prices. The research was carried out by using costumer satisfaction rating by comparing with the competitor companies. Based on calculation using QFD method, it shows that split liner has the highest percentage of technical requirement in tire industry about 30,57%. The second factor is pattern design about 25,98%. Then, the third factor is compound technology about 22,68%. Therefore, the researchers can recommend several strategies for the quality improvement based on customer needs for the tire industry.

Experimental Autonomous Road Vehicle with Logical Artificial Intelligence

Directory of Open Access Journals (Sweden)

Sergey Sergeevich Shadrin

2017-01-01

Full Text Available This article describes some technical issues regarding the adaptation of a production car to a platform for the development and testing of autonomous driving technologies. A universal approach to performing the reverse engineering of electric power steering (EPS for the purpose of external control is also presented. The primary objective of the related study was to solve the problem associated with the precise prediction of the dynamic trajectory of an autonomous vehicle. This was accomplished by deriving a new equation for determining the lateral tire forces and adjusting some of the vehicle parameters under road test conductions. A Mivar expert system was also integrated into the control system of the experimental autonomous vehicle. The expert system was made more flexible and effective for the present application by the introduction of hybrid artificial intelligence with logical reasoning. The innovation offers a solution to the major problem of liability in the event of an autonomous transport vehicle being involved in a collision.

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks

Science.gov (United States)

Sol-Sánchez, Miguel; Moreno-Navarro, Fernando; Rubio-Gámez, Mª Carmen

2014-01-01

Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats) to be used in railway tracks. PMID:28788168

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks

Directory of Open Access Journals (Sweden)

Miguel Sol-Sánchez

2014-08-01

Full Text Available Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats to be used in railway tracks.

Vibration Analysis of a Tire in Ground Contact under Varied Conditions

Directory of Open Access Journals (Sweden)

Karakus Murat

2017-03-01

Full Text Available The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13 has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different coefficients of friction. Experiments are run under certain conditions to check the accuracy of the numerical model. The natural frequencies are measured to describe free vibration and vibration of the tire contacted by ground, using a damping monitoring method. It is seen, that experimental and numerical results are in good agreement. On the other hand, investigating the impact of three different factors together is quite difficult on the natural frequencies. When some of these factors are assumed to be constant and the variables are taken one by one, it is easier to assess the effects.

Compaction-Based Deformable Terrain Model as an Interface for Real-Time Vehicle Dynamics Simulations

Science.gov (United States)

2013-04-16

N.Y. [20] Wulfsohn, D., and Upadhyaya, S. K., 1992, "Prediction of traction and soil compaction using three-dimensional soil- tyre contact profile," Journal of Terramechanics, 29(6), pp. 541-564. ...the relative speedup of utilizing GPUs for computational acceleration. INTRODUCTION In order to enable off- road vehicle dynamics analysis...ANSI Std Z39-18 Page 2 of 8 Figure 2. Tire geometry used to determine collision points with the terrain In the context of off- road vehicle

A brief description of the biomechanics and physiology of a strongman event: the tire flip.

Science.gov (United States)

Keogh, Justin W L; Payne, Amenda L; Anderson, Brad B; Atkins, Paul J

2010-05-01

The purpose of this study was to (a) characterize the temporal aspects of a popular strongman event, the tire flip; (b) gain some insight into the temporal factors that could distinguish the slowest and fastest flips; and (c) obtain preliminary data on the physiological stress of this exercise. Five resistance-trained subjects with experience in performing the tire flip gave informed consent to participate in this study. Each subject performed 2 sets of 6 tire flips with a 232-kg tire with 3 minutes of rest between sets. Temporal variables were obtained from video cameras positioned 10 m from the tire, perpendicular to the intended direction of the tire flip. Using the "stopwatch" function in Silicon Coach, the duration of each tire flip and that of the first pull, second pull, transition, and push phases were recorded. Physiological stress was estimated via heart rate and finger-prick blood lactate response. Independent T-tests revealed that the 2 faster subjects (0.38 +/- 0.17 s) had significantly (p tire flip performance and that this exercise provides relatively high degrees of physiological stress.

Economic and policy instrument analyses in support of the scrap tire recycling program in Taiwan.

Science.gov (United States)

Chang, Ni-Bin

2008-02-01

Understanding the cost-effectiveness and the role of economic and policy instruments, such as the combined product tax-recycling subsidy scheme or a tradable permit, for scrap tire recycling has been of crucial importance in a market-oriented environmental management system. Promoting product (tire) stewardship on one hand and improving incentive-based recycling policy on the other hand requires a comprehensive analysis of the interfaces and interactions in the nexus of economic impacts, environmental management, environmental valuation, and cost-benefit analysis. This paper presents an assessment of the interfaces and interactions between the implementation of policy instruments and its associated economic evaluation for sustaining a scrap tire recycling program in Taiwan during the era of the strong economic growth of the late 1990s. It begins with an introduction of the management of the co-evolution between technology metrics of scrap tire recycling and organizational changes for meeting the managerial goals island-wide during the 1990s. The database collected and used for such analysis covers 17 major tire recycling firms and 10 major tire manufacturers at that time. With estimates of scrap tire generation and possible scale of subsidy with respect to differing tire recycling technologies applied, economic analysis eventually leads to identify the associated levels of product tax with respect to various sizes of new tires. It particularly demonstrates a broad perspective of how an integrated econometric and engineering economic analysis can be conducted to assist in implementing policy instruments for scrap tire management. Research findings indicate that different subsidy settings for collection, processing, and end use of scrap tires should be configured to ameliorate the overall managerial effectiveness. Removing the existing boundaries between designated service districts could strengthen the competitiveness of scrap tires recycling industry, helping to

Impacts of environmental conditions on the sorption of volatile organic compounds onto tire powder

Energy Technology Data Exchange (ETDEWEB)

Oh, Dong I. [Division of R and D Planning and Management, Korea Institute of Environmental Science and Technology, Seoul (Korea, Republic of); Nam, Kyongphile [School of Civil, Urban and Geosystem Engineering, College of Engineering, Seoul National University, Gwanak-Ku, 151-742 Seoul (Korea, Republic of); Park, Jae W. [Department of Civil Engineering, Hanyang University, Seoul (Korea, Republic of); Khim, Jee H. [Department of Civil and Environmental Engineering, Korea University, Seoul (Korea, Republic of); Kim, Yong K. [School of Civil, Urban and Geosystem Engineering, College of Engineering, Seoul National University, Gwanak-Ku, 151-742 Seoul (Korea, Republic of); Kim, Jae Y. [School of Civil, Urban and Geosystem Engineering, College of Engineering, Seoul National University, Gwanak-Ku, 151-742 Seoul (Korea, Republic of)], E-mail: jaeykim@snu.ac.kr

2008-05-01

A series of batch tests were performed and the impacts of environmental conditions and phase change on the sorption of volatile organic compounds (VOCs) were investigated. Benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene were selected as target VOCs. Sorption of VOCs onto tire powder was well demonstrated by a linear-partitioning model. Water-tire partition coefficients of VOCs (not tested in this study) could be estimated using a logarithmic relationship between observed water-tire partition coefficients and octanol-water partition coefficients of the VOCs tested. The target VOCs did not seem to compete with other VOCs significantly when sorbed onto the tire powder for the range of concentrations tested. The influence of environmental conditions, such as pH and ionic strength also did not seem to be significant. Water-tire partition coefficients of benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene decreased as the sorbent dosage increased. However, they showed stable values when the sorbent dosage was greater than 10 g/L. Air-tire partition coefficient could be extrapolated from Henry's law constants and water-tire partition coefficient of VOCs.

Impacts of environmental conditions on the sorption of volatile organic compounds onto tire powder

International Nuclear Information System (INIS)

Oh, Dong I.; Nam, Kyongphile; Park, Jae W.; Khim, Jee H.; Kim, Yong K.; Kim, Jae Y.

2008-01-01

A series of batch tests were performed and the impacts of environmental conditions and phase change on the sorption of volatile organic compounds (VOCs) were investigated. Benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene were selected as target VOCs. Sorption of VOCs onto tire powder was well demonstrated by a linear-partitioning model. Water-tire partition coefficients of VOCs (not tested in this study) could be estimated using a logarithmic relationship between observed water-tire partition coefficients and octanol-water partition coefficients of the VOCs tested. The target VOCs did not seem to compete with other VOCs significantly when sorbed onto the tire powder for the range of concentrations tested. The influence of environmental conditions, such as pH and ionic strength also did not seem to be significant. Water-tire partition coefficients of benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene decreased as the sorbent dosage increased. However, they showed stable values when the sorbent dosage was greater than 10 g/L. Air-tire partition coefficient could be extrapolated from Henry's law constants and water-tire partition coefficient of VOCs

Simultaneous Observation of Hybrid States for Cyber-Physical Systems: A Case Study of Electric Vehicle Powertrain.

Science.gov (United States)

Lv, Chen; Liu, Yahui; Hu, Xiaosong; Guo, Hongyan; Cao, Dongpu; Wang, Fei-Yue

2017-08-22

As a typical cyber-physical system (CPS), electrified vehicle becomes a hot research topic due to its high efficiency and low emissions. In order to develop advanced electric powertrains, accurate estimations of the unmeasurable hybrid states, including discrete backlash nonlinearity and continuous half-shaft torque, are of great importance. In this paper, a novel estimation algorithm for simultaneously identifying the backlash position and half-shaft torque of an electric powertrain is proposed using a hybrid system approach. System models, including the electric powertrain and vehicle dynamics models, are established considering the drivetrain backlash and flexibility, and also calibrated and validated using vehicle road testing data. Based on the developed system models, the powertrain behavior is represented using hybrid automata according to the piecewise affine property of the backlash dynamics. A hybrid-state observer, which is comprised of a discrete-state observer and a continuous-state observer, is designed for the simultaneous estimation of the backlash position and half-shaft torque. In order to guarantee the stability and reachability, the convergence property of the proposed observer is investigated. The proposed observer are validated under highly dynamical transitions of vehicle states. The validation results demonstrates the feasibility and effectiveness of the proposed hybrid-state observer.

Characterization of Semi-Volatile Organic Chemicals from Tire Crumb Rubber

Science.gov (United States)

Recycled tire crumb rubber (TCR) is often used as infill material in synthetic turf playing fields as well as some playgrounds. Concerns have been raised about the safety of this material and a multi-agency Federal Research Action Plan on Recycled Tire Crumb Used on Playing Field...

Increased efficiency in the second-hand tire trade provides opportunity for dengue control.

Science.gov (United States)

Pliego Pliego, Emilene; Velázquez-Castro, Jorge; Eichhorn, Markus P; Fraguela Collar, Andrés

2018-01-21

Dengue fever is increasing in geographical range, spread by invasion of its vector mosquitoes. The trade in second-hand tires has been implicated as a factor in this process because they act as mobile reservoirs of mosquito eggs and larvae. Regional transportation of tires can create linkages between rural areas with dengue and disease-free urban areas, potentially giving rise to outbreaks even in areas with strong local control measures. In this work we sought to model the dynamics of mosquito transportation via the tire trade, in particular to predict its role in causing unexpected dengue outbreaks through vertical transmission of the virus across generations of mosquitoes. We also aimed to identify strategies for regulating the trade in second-hand tires, improving disease control. We created a mathematical model which captures the dynamics of dengue between rural and urban areas, taking into account the movement and storage time of tires, and mosquito diapause. We simulate a series of scenarios in which a mosquito population is introduced to a dengue-free area via movement of tires, either as single or multiple events, increasing the likelihood of a dengue outbreak. A persistent disease state can be induced regardless of whether urban conditions for an outbreak are met, and an existing endemic state can be enhanced by vector input. Finally we assess the potential for regulation of tire processing as a means of reducing the transmission of dengue fever using a specific case study from Puerto Rico. Our work demonstrates the importance of the second-hand tire trade in modulating the spread of dengue fever across regions, in particular its role in introducing dengue to disease-free areas. We propose that reduction of tire storage time and control of their movement can play a crucial role in containing dengue outbreaks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Numerical Study of Tire Hydroplaning Based on Power Spectrum of Asphalt Pavement and Kinetic Friction Coefficient

Directory of Open Access Journals (Sweden)

Shengze Zhu

2017-01-01

Full Text Available Hydroplaning is a driving phenomenon threating vehicle’s control stability and safety. It happens when tire rolls on wet pavement with high speed that hydrodynamic force uplifts the tire. Accurate numerical simulation to reveal the mechanism of hydroplaning and evaluate the function of relevant factors in this process is significant. In order to describe the friction behaviors of tire-pavement interaction, kinetic friction coefficient curve of tire rubber and asphalt pavement was obtained by combining pavement surface power spectrum and complex modulus of tread rubber through Persson’s friction theory. Finite element model of tire-fluid-pavement was established in ABAQUS, which was composed of a 225-40-R18 radial tire and three types of asphalt pavement covered with water film. Mechanical responses and physical behaviors of tire-pavement interaction were observed and compared with NASA equation to validate the applicability and accuracy of this model. Then contact force at tire-pavement interface and critical hydroplaning speed influenced by tire inflation pressure, water film thickness, and pavement types were investigated. The results show higher tire inflation pressure, thinner water film, and more abundant macrotexture enhancing hydroplaning speed. The results could be applied to predict hydroplaning speed on different asphalt pavement and improve pavement skid resistance design.

Modularised eco-innovation in the auto industry

DEFF Research Database (Denmark)

Christensen, Thomas Budde

2011-01-01

The article explores the integration of alternative drivetrain solutions in the automotive industry. The article includes an analysis of the structure of the conventional automotive value chain and presents four examples of alternative vehicle designs. The article concludes that the component sha...... sharing across drivetrain solutions such as the battery electric, the hybrid and the fuel cell system opens a window of opportunity for modular design strategies that may make integration into the otherwise locked conventional production system possible....

Perfect sound insulation property of reclaimed waste tire rubber

Science.gov (United States)

Ubaidillah, Harjana, Yahya, Iwan; Kristiani, Restu; Muqowi, Eki; Mazlan, Saiful Amri

2016-03-01

This article reports an experimental investigation of sound insulation and absorption performance of a materials made of reclaimed ground tire rubber which is known as un-recyclable thermoset. The bulk waste tire is processed using single step recycling methods namely high-pressure high-temperature sintering (HPHTS). The bulk waste tire is simply placed into a mold and then a pressure load of 3 tons and a heating temperature of 200°C are applied to the mold. The HPHTS conducted for an hour and then it is cooled in room temperature. The resulted product is then evaluated the acoustical properties namely sound transmission loss (STL) and sound absorption coefficient using B&K Tube Kit Type 4206-T based on ISO 10534-2, ASTM E1050 and ASTM E2611. The sound absorption coefficient is found about 0.04 until 0.08 while STL value ranges between 50 to 60 dB. The sound absorption values are found to be very low (<0.1), while the average STL is higher than other elastomeric matrix found in previous work. The reclaimed tire rubber through HPHTS technique gives good soundproof characteristic.

Chromium removal from water by activated carbon developed from waste rubber tires.

Science.gov (United States)

Gupta, Vinod Kumar; Ali, Imran; Saleh, Tawfik A; Siddiqui, M N; Agarwal, Shilpi

2013-03-01

Because of the continuous production of large amount of waste tires, the disposal of waste tires represents a major environmental issue throughout the world. This paper reports the utilization of waste tires (hard-to-dispose waste) as a precursor in the production of activated carbons (pollution-cleaning adsorbent). In the preparation of activated carbon (AC), waste rubber tire (WRT) was thermally treated and activated. The tire-derived activated carbon was characterized by means of scanning electron microscope, energy-dispersive X-ray spectroscopy, FTIR spectrophotometer, and X-ray diffraction. In the IR spectrum, a number of bands centred at about 3409, 2350, 1710, 1650, and 1300-1000 cm(-1) prove the present of hydroxyl and carboxyl groups on the surface of AC in addition to C═C double bonds. The developed AC was tested and evaluated as potential adsorbent removal of chromium (III). Experimental parameters, such as contact time, initial concentration, adsorbent dosage and pH were optimized. A rapid uptake of chromium ions was observed and the equilibrium is achieved in 1 h. It was also found that the adsorption process is pH dependent. This work adds to the global discussion of the cost-effective utilization of waste rubber tires for waste water treatment.

A North American model to contain the spread of Aedes albopictus through tire legislation.

Science.gov (United States)

Novak, R J

1995-12-01

The introduction, spread, and establishment of the Asian tiger mosquito, Aedes albopictus, in the United States has been facilitated by used or waste tires. This species has not only caused considerable concern among public health officials but also highlighted that the growing accumulations of used tires are a serious solid waste problem and a challenge to the recycling industry. This paper illustrates how the State of Illinois addressed the public health and solid waste problems associated with waste tires, mosquitoes and mosquito-borne pathogens. The goal of the State was to develop and implement through legislative process the Illinois Waste Tire Act. The purpose of the Waste Tire Act is: 1) to ensure that used and waste tires are collected for disposal and recycling, 2) to provide for the abatement of used and waste tire dumps and associated threats to public health, 3) to encourage the development of used and waste tire processing facilities and technologies, including energy recovery, and 4) to provide for research on vectors associated with used and waste tires, and the diseases they spread. The discussion will include key statutes from the Act and the model used to coordinate the effort of five different governmental agencies. An up-to-date presentation of vector-related research, mandated by the Act, ranging from applied investigations on mosquito control to more basic studies investigations on virus identification using molecular technology will be discussed. Finally a discussion of problems that have been encountered along with solutions dealing with legislative language, multidisciplined agency efforts and interactions with the general public are presented.

Management of used tires, accomplishments in the world, and situation in Serbia

Directory of Open Access Journals (Sweden)

Stanojević Dušan D.

2011-01-01

Full Text Available It is estimated that all over the world there are more than 550 million road vehicles in everyday use. Annually, 1.3 billion used tyres are dismantled from these vehicles due to safety reasons. A small number of these tyres end up reused as second-hand tyres or, after being retreated, as new ones. The rest are end of life tyres which are recycled or used as tire derived fuels under controlled combustion conditions. Modern vehicle tyres are a high-technological product containing, on the average, 85% hydrocarbon, 10-15% steel, as well as some other chemical materials. Tyres belong to high caloric materials, with calorific value of a passenger car tyre of approx. 30.2 MJ/kg being more than of hard coal and comparable to calorific value of petrol-coke. Having this in mind many countries use end of life tyres as safe alternative fuel in cement works or power plants. Undeveloped countries dump end of life tyres on legal and illegal scrap stockpiles. End of life tyres, if deposed correctly, don’t endanger the environment because they are chemically inert. However, since they can easily be burnt there is a real possibility of tyre dump fires, which in effect can lead to harmful products emission that extremely pollute the environment. End of life tyres represent a very important secondary material, which when recycled is transformed into a number of raw materials used in rubber industry, for road construction, sports facilities, residential and business buildings, artificial fish habitats in shallow seas, sea walls, steel production, etc. By the industrial procedures of controlled degradation, which have been uneconomical up till now, gaseous and liquid fuel can be obtained by natural rubber, steel and soot recycling. The countries of the EU, together with Norway and Switzerland, were the world leaders in the field of effective end of life tyre management in the year 2009. Out of 2.62 million tonnes of end of life tyres, 95% were restored or used as

Dielectric properties of various polymers (PVC, EVA, HDPE, and PP) reinforced with ground tire rubber (GTR)

OpenAIRE

Mujal Rosas, Ramón María; Marín Genescá, Marcos; Ballart Prunell, Jordi

2015-01-01

Mass production of tires as well as its difficult storage or elimination is a real environmental problem. Various methods for recycling tires are currently used, such as mechanical crushing, which puts vulcanized rubber, steel, and fibers apart. The rubber may be used in several industrial applications such as flooring, insulations, and footwear. The present paper focuses on finding a new application for old used tires [ground tire rubber (GTR)]. To this end, tires dust has been mixed with va...

Prospective of Macedonia for treatment and recycling of tire waste with Pirolitic process

Directory of Open Access Journals (Sweden)

Sarafov Victor

2017-01-01

Full Text Available The automotive industry is one of the ever-developing branches of modern society and therefore collecting and recycling of old tires must not be ignored. It must be taken into consideration that tire waste is decomposing at an extremely low pace under the influence of climate factors, that waste from used tires not only is covering large areas, but there is also a possibility of spontaneous fire that is usually long-lasting and emits gasses that have negative effect on human health. Tires are made of complex polymeric materials and contain chemical additives. When burning tires on an open field highly toxic and cancerous organic compounds are being released (biphenyl, anthracene, fluoranthene and other toxins. Pyrolysis is a process that offers sustainable management of this type of waste which in continuation is to be explained in detail.

A Tire-Sulfur Hybrid Adsorption Denitrification (T-SHAD) process for decentralized wastewater treatment.

Science.gov (United States)

Krayzelova, Lucie; Lynn, Thomas J; Banihani, Qais; Bartacek, Jan; Jenicek, Pavel; Ergas, Sarina J

2014-09-15

Nitrogen discharges from decentralized wastewater treatment (DWT) systems contribute to surface and groundwater contamination. However, the high variability in loading rates, long idle periods and lack of regular maintenance presents a challenge for biological nitrogen removal in DWT. A Tire-Sulfur Hybrid Adsorption Denitrification (T-SHAD) process was developed that combines nitrate (NO3(-)) adsorption to scrap tire chips with sulfur-oxidizing denitrification. This allows the tire chips to adsorb NO3(-) when the influent loading exceeds the denitrification capacity of the biofilm and release it when NO3(-) loading rates are low (e.g. at night). Three waste products, scrap tire chips, elemental sulfur pellets and crushed oyster shells, were used as a medium in adsorption, leaching, microcosm and up-flow packed bed bioreactor studies of NO3(-) removal from synthetic nitrified DWT wastewater. Adsorption isotherms showed that scrap tire chips have an adsorption capacity of 0.66 g NO3(-)-N kg(-1) of scrap tires. Leaching and microcosm studies showed that scrap tires leach bioavailable organic carbon that can support mixotrophic metabolism, resulting in lower effluent SO4(2-) concentrations than sulfur oxidizing denitrification alone. In column studies, the T-SHAD process achieved high NO3(-)-N removal efficiencies under steady state (90%), variable flow (89%) and variable concentration (94%) conditions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Analysis of Tire Tractive Performance on Deformable Terrain by Finite Element-Discrete Element Method

Science.gov (United States)

Nakashima, Hiroshi; Takatsu, Yuzuru

The goal of this study is to develop a practical and fast simulation tool for soil-tire interaction analysis, where finite element method (FEM) and discrete element method (DEM) are coupled together, and which can be realized on a desktop PC. We have extended our formerly proposed dynamic FE-DE method (FE-DEM) to include practical soil-tire system interaction, where not only the vertical sinkage of a tire, but also the travel of a driven tire was considered. Numerical simulation by FE-DEM is stable, and the relationships between variables, such as load-sinkage and sinkage-travel distance, and the gross tractive effort and running resistance characteristics, are obtained. Moreover, the simulation result is accurate enough to predict the maximum drawbar pull for a given tire, once the appropriate parameter values are provided. Therefore, the developed FE-DEM program can be applied with sufficient accuracy to interaction problems in soil-tire systems.

High Value Scrap Tire Recycle

Energy Technology Data Exchange (ETDEWEB)

Bauman, B. D.

2003-02-01

The objectives of this project were to further develop and scale-up a novel technology for reuse of scrap tire rubber, to identify and develop end uses for the technology (products), and to characterize the technology's energy savings and environmental impact.

Thermodynamics of the vehicle. 2. ed.; Thermodynamik des Kraftfahrzeugs

Energy Technology Data Exchange (ETDEWEB)

Stan, Cornel [California Univ., Berkeley, CA (United States); Paris Univ., 75 (France); Pisa Univ. (Italy); Perugia Univ. (Italy); Kronstadt Univ. (Russian Federation)

2012-07-01