Improving Vegetable Oil Fueled CI Engine Characteristics Through Diethyl Ether Blending

KAUST Repository

Vedharaj, S.

2016-12-01

In this research, the flow and ignition properties of vegetable oil (VO) are improved by blending it with diethyl ether (DEE). DEE, synthesized from ethanol, has lower viscosity than diesel and VO. When DEE is blended with VO, the resultant DEEVO mixtures have favorable properties for compression ignition (CI) engine operation. As such, DEEVO20 (20% DEE + 80% VO) and DEEVO40 (40% DEE + 60% VO) were initially considered in the current study. The viscosity of VO is 32.4*10−6 m2/s; the viscosity is reduced with the increase of DEE in VO. In this study, our blends were limited to a maximum of 40% DEE in VO. The viscosity of DEEVO40 is 2.1*10−6 m2/s, which is comparable to that of diesel (2.3*10−6 m2/s). The lower boiling point and flash point of DEE improves the fuel spray and evaporation for DEEVO mixtures. In addition to the improvement in physical properties, the ignition quality of DEEVO mixtures is also improved, as DEE is a high cetane fuel (DCN = 139). The ignition characteristics of DEEVO mixtures were studied in an ignition quality tester (IQT). There is an evident reduction in ignition delay time (IDT) for DEEVO mixtures compared to VO. The IDT of VO (4.5 ms), DEEVO20 (3.2 ms) and DEEVO40 (2.7 ms) was measured in IQT. Accordingly, the derived cetane number (DCN) of DEEVO mixtures increased with the increase in proportion of DEE. The reported mixtures were also tested in a single cylinder CI engine. The start of combustion (SOC) was advanced for DEEVO20 and DEEVO40 compared to diesel, which is attributed to the high DCN of DEEVO mixtures. On the other hand, the peak heat release rate decreased for DEEVO mixtures compared to diesel. Gaseous emissions such as nitrogen oxide (NOX), total hydrocarbon (THC) and smoke were reduced for DEEVO mixtures compared to diesel. The physical and ignition properties of VO are improved by the addition of DEE, and thus, the need for the trans-esterification process is averted. Furthermore, this blending strategy is simpler

Improving Vegetable Oil Fueled CI Engine Characteristics Through Diethyl Ether Blending

KAUST Repository

Vedharaj, S.; Vallinayagam, R.; Sarathy, Mani; Dibble, Robert W.

2016-01-01

In this research, the flow and ignition properties of vegetable oil (VO) are improved by blending it with diethyl ether (DEE). DEE, synthesized from ethanol, has lower viscosity than diesel and VO. When DEE is blended with VO, the resultant DEEVO mixtures have favorable properties for compression ignition (CI) engine operation. As such, DEEVO20 (20% DEE + 80% VO) and DEEVO40 (40% DEE + 60% VO) were initially considered in the current study. The viscosity of VO is 32.4*10−6 m2/s; the viscosity is reduced with the increase of DEE in VO. In this study, our blends were limited to a maximum of 40% DEE in VO. The viscosity of DEEVO40 is 2.1*10−6 m2/s, which is comparable to that of diesel (2.3*10−6 m2/s). The lower boiling point and flash point of DEE improves the fuel spray and evaporation for DEEVO mixtures. In addition to the improvement in physical properties, the ignition quality of DEEVO mixtures is also improved, as DEE is a high cetane fuel (DCN = 139). The ignition characteristics of DEEVO mixtures were studied in an ignition quality tester (IQT). There is an evident reduction in ignition delay time (IDT) for DEEVO mixtures compared to VO. The IDT of VO (4.5 ms), DEEVO20 (3.2 ms) and DEEVO40 (2.7 ms) was measured in IQT. Accordingly, the derived cetane number (DCN) of DEEVO mixtures increased with the increase in proportion of DEE. The reported mixtures were also tested in a single cylinder CI engine. The start of combustion (SOC) was advanced for DEEVO20 and DEEVO40 compared to diesel, which is attributed to the high DCN of DEEVO mixtures. On the other hand, the peak heat release rate decreased for DEEVO mixtures compared to diesel. Gaseous emissions such as nitrogen oxide (NOX), total hydrocarbon (THC) and smoke were reduced for DEEVO mixtures compared to diesel. The physical and ignition properties of VO are improved by the addition of DEE, and thus, the need for the trans-esterification process is averted. Furthermore, this blending strategy is simpler

Stability of traditionally processed vegetable oils and their blends ...

African Journals Online (AJOL)

physicochemical properties which included acid value, saponification value, peroxide value, iodine ... The oils and their blends were stored in two different conditions; one batch at the air-tight .... about 0.5 ml of starch indicator solution was.

Detection of argan oil adulterated with vegetable oils: New markers

Energy Technology Data Exchange (ETDEWEB)

Ourrach, I.; Rada, M.; Perez-Camino, M. C.; Benaissa, M.; Guinda, A

2012-07-01

This work aims to contribute to controlling the authenticity of pure argan oil, a valuable Moroccan product. Fatty acids, hydrocarbon fraction, 3,5-stigmastadiene, the alkyl esters of fatty acids, chlorophyllic pigments and physical properties such as viscosity, density and refractive index were studied in order to detect the adulteration of argan oil with edible vegetable oils. The results found in this study show that 3,5-stigmastadiene, kaurene and pheophytin-a can be used as possible new markers for argan oil blends of up to 5% with refined, sunflower and virgin olive oils. Due to the similarity of the fatty acid compositions of the edible oils studied and argan oil, fatty acids can be employed as markers for the detection of argan oil adulteration at levels higher than 10%. Among the physical properties studied, the refractive index shows significant differences for sunflower oil and its blend at 10% with argan oil. (Author) 35 refs.

Performance of Diesel Engine Using Blended Crude Jatropha Oil

Science.gov (United States)

Kamarudin, Kamarul Azhar; Mohd Sazali, Nor Shahida Akma; Mohd Ali, Mas Fauzi; Alimin, Ahmad Jais; Khir, Saffiah Abdullah

2010-06-01

Vegetable oil presents a very promising alternative to diesel oil since it is renewable and has similar properties to the diesel. In view of this, crude jatropha oil is selected and its viscosity is reduced by blending it with diesel. Since jatropha oil has properties which are similar to mineral diesel, it can be used in compression ignition engines without any engine modification. This paper presents the results of investigation carried out on a four-cylinder, four strokes and indirect-injection diesel engine. The engine, operated using composition blends of crude jatropha oil and diesel, were compared with mineral diesel. An experimental investigation has been carried out to analyze the performance characteristics of a compression ignition engine from the blended fuel (5%, 10%, 20% and 30%). A naturally aspirated four-stroke indirect injection diesel engine was tested at full load conditions, speeds between 1000 and 3500 rpm with intervals of 500 rpm. Results obtained from the measures of torque, power, specific fuel consumptions, thermal efficiency and brake mean effective pressure are nearly the same between blended and diesel fuel. An overall graph shows that the performance of relevant parameters from blended fuel is most likely similar to the performance produced from diesel. The experimental results proved that the use of crude jatropha oil in compression ignition engines is a viable alternative to diesel.

Quantification of rice bran oil in oil blends

Energy Technology Data Exchange (ETDEWEB)

Mishra, R.; Sharma, H. K.; Sengar, G.

2012-11-01

Blends consisting of physically refined rice bran oil (PRBO): sunflower oil (SnF) and PRBO: safflower oil (SAF) in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil. (Author) 23 refs.

Jatropha oil methyl ester and its blends used as an alternative fuel in diesel engine

Directory of Open Access Journals (Sweden)

Yarrapathruni Rao Hanumantha Venkata

2009-01-01

Full Text Available Biomass derived vegetable oils are quite promising alternative fuels for agricultural diesel engines. Use of vegetable oils in diesel engines leads to slightly inferior performance and higher smoke emissions due to their high viscosity. The performance of vegetable oils can be improved by modifying them through the transesterification process. In this present work, the performance of single cylinder water-cooled diesel engine using methyl ester of jatropha oil as the fuel was evaluated for its performance and exhaust emissions. The fuel properties of biodiesel such as kinematic viscosity, calorific value, flash point, carbon residue, and specific gravity were found. Results indicate that B25 has closer performance to diesel and B100 has lower brake thermal efficiency mainly due to its high viscosity compared to diesel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel fuel at tested load conditions and there was no difference of efficiency between the biodiesel and its blended fuels. For jatropha biodiesel and its blended fuels, the exhaust gas temperature increased with the increase of power and amount of biodiesel. However, its diesel blends showed reasonable efficiency, lower smoke, and CO2 and CO emissions.

Vegetable oil-derived epoxy monomers and polymer blends: A comparative study with review

Directory of Open Access Journals (Sweden)

T. P. Schuman

2013-03-01

Full Text Available Glycidyl esters of epoxidized fatty acids derived from soybean oil (EGS and linseed oil (EGL have been synthesized to have higher oxirane content, more reactivity and lower viscosity than epoxidized soybean oil (ESO or epoxidized linseed oil (ELO. The EGS and ESO, for comparison, were used neat and in blends with diglycidyl ether of bisphenol A (DGEBA. Thermosetting resins were fabricated with the epoxy monomers and either BF3 catalyst or anhydride. The curing behaviors, glass transition temperatures, crosslink densities and mechanical properties were tested. The results indicated that polymer glass transition temperatures were mostly a function of oxirane content with additional influence of glycidyl versus internal oxirane reactivity, pendant chain content, and chemical structure and presence of saturated components. EGS provided better compatibility with DGEBA, improved intermolecular crosslinking and glass transition temperature, and yielded mechanically stronger polymerized materials than materials obtained using ESO. Other benefits of the EGS resin blend systems were significantly reduced viscosities compared to either DGEBA or ESO-blended DGEBA counterparts. Therefore, EGS that is derived from renewable sources has improved potential for fabrication of structural and structurally complex epoxy composites, e.g., by vacuum-assisted resin transfer molding.

Oxidative stability of biodiesel blends derived from waste frying oils

Directory of Open Access Journals (Sweden)

Michael Feroldi

2017-07-01

Full Text Available The high cost of biodiesel production is mainly linked to the price of raw material.This factor has favored the use of alternative fats and oils such as those used in frying. Since biodiesel can be obtained from several vegetable and animal raw materials, the physicochemical characteristics of the fuel may vary considerably. One of these characteristics is the fatty acid composition. It directly affects the oxidative stability of biodiesel, which can be impaired when the fuel undergoes exposure to sunlight, metals, oxygen and high temperatures. In order to improve the oxidative stability of biodiesels produced from waste frying oil some studies involving blends of different raw materials have been carried out. In this sense, this work aimed to assess the characteristics resulting from the blending of soybean waste frying oil with other waste biodiesels in what concerns to oxidation. The blends of fatty materials were obtained by means of a 2² factorial design. The induction periods of biodiesel blends were enough to meet the ASTM D6751 standard. Swine fat was responsible for the increase in the induction period values.

Anti-obesity effect of a traditional Chinese dietary habit-blending lard with vegetable oil while cooking.

Science.gov (United States)

Wang, Ji; Yan, Sisi; Xiao, Haisi; Zhou, Huijuan; Liu, Shuiping; Zeng, Yu; Liu, Biying; Li, Rongfang; Yuan, Zhihang; Wu, Jing; Yi, Jine; Razack, Yarou Bao Sero; Wen, Lixin

2017-10-31

Obesity, which is associated with dietary habits, has become a global social problem and causes many metabolic diseases. In China, both percentages of adult obesity and overweight are far lower compared to western countries. It was designed to increase the two levels of daily intake in human, namely 3.8% and 6.5%, which are recommendatory intake (25 g/d) and Chinese citizens' practical intake (41.4 g/d), respectively. The mice were respectively fed with feeds added with soybean oil, lard or the oil blended by both for 12 weeks. In the mice fed with diet containing 3.8% of the three oils or 6.5% blended oil, their body weight, body fat rate, cross-sectional area of adipocytes, adipogenesis and lipogenesis in adipose were decreased, whereas hydrolysis of triglyserides in adipose was increased. This study demonstrated that the oil mixture containing lard and soybean oil had a remarkable anti-obesity effect. It suggests that the traditional Chinese dietary habits using oils blended with lard and soybean oil, might be one of the factors of lower percentages of overweight and obesity in China, and that the increasing of dietary oil intake and the changing of its component resulted in the increasing of obesity rate in China over the past decades.

Fuel Continuous Mixer ? an Approach Solution to Use Straight Vegetable Oil for Marine Diesel Engines

OpenAIRE

Đặng Van Uy; Tran The Nam

2018-01-01

The vegetable oil is well known as green fuel for diesel engines due to its low sunphur content and renewable stock. However, there are some problems raising when vegetable oil is used as fuel for diesel engines such as highly effected by cold weather, lower general efficiency, separation in layer if mixed with diesel oil and so on. To overcome that disadvantiges, the authors propose a new idea that to use a continuous fuel mixer to blend vegetable oil with diesel oil to make so called a mixe...

Combustion and emission characteristics of diesel engine fuelled with rice bran oil methyl ester and its diesel blends

Directory of Open Access Journals (Sweden)

Gattamaneni Rao Narayana Lakshmi

2008-01-01

Full Text Available There has been a worldwide interest in searching for alternatives to petroleum-derived fuels due to their depletion as well as due to the concern for the environment. Vegetable oils have capability to solve this problem because they are renewable and lead to reduction in environmental pollution. The direct use of vegetable oils as a diesel engine fuel is possible but not preferable because of their extremely higher viscosity, strong tendency to polymerize and bad cold start properties. On the other hand, Biodiesels, which are derived from vegetable oils, have been recently recognized as a potential alternative to diesel oil. This study deals with the analysis of rice bran oil methyl ester (RBME as a diesel fuel. RBME is derived through the transesterification process, in which the rice bran oil reacts with methanol in the presence of KOH. The properties of RBME thus obtained are comparable with ASTM biodiesel standards. Tests are conducted on a 4.4 kW, single-cylinder, naturally aspirated, direct-injection air-cooled stationary diesel engine to evaluate the feasibility of RBME and its diesel blends as alternate fuels. The ignition delay and peak heat release for RBME and its diesel blends are found to be lower than that of diesel and the ignition delay decreases with increase in RBME in the blend. Maximum heat release is found to occur earlier for RBME and its diesel blends than diesel. As the amount of RBME in the blend increases the HC, CO, and soot concentrations in the exhaust decreased when compared to mineral diesel. The NOx emissions of the RBME and its diesel blends are noted to be slightly higher than that of diesel.

PERFORMANCE AND EMISSION CHARACTERISTICS OF CI ENGINE FUELLED WITH NON EDIBLE VEGETABLE OIL AND DIESEL BLENDS

Directory of Open Access Journals (Sweden)

T. ELANGO

2011-04-01

Full Text Available This study investigates performance and emission characteristics of a diesel engine which is fuelled with different blends of jatropha oil and diesel (10–50%. A single cylinder four stroke diesel engine was used for the experiments at various loads and speed of 1500 rpm. An AVL 5 gas analyzer and a smoke meter were used for the measurements of exhaust gas emissions. Engine performance (specific fuel consumption SFC, brake thermal efficiency, and exhaust gas temperature and emissions (HC, CO, CO2, NOx and Smoke Opacity were measured to evaluate and compute the behaviour of the diesel engine running on biodiesel. The results showed that the brake thermal efficiency of diesel is higher at all loads. Among the blends maximum brake thermal efficiency and minimum specific fuel consumption were found for blends upto 20% Jatropha oil. The specific fuel consumption of the blend having 20% Jatropha oil and 80% diesel (B20 was found to be comparable with the conventional diesel. The optimum blend is found to be B20 as the CO2 emissions were lesser than diesel while decrease in brake thermal efficiency is marginal.

Production of vegetable oil blends and structured lipids and their effect on wound healing

Directory of Open Access Journals (Sweden)

Juliana Neves Rodrigues Ract

2015-06-01

Full Text Available Two oil blends (sunflower/canola oils 85/15 (BL1 and canola/linseed oils 70/30 (BL2, were prepared and enzymatically interesterified to be applied to surgically-induced wounds in rats. Following surgery, the animals were submitted to the Treatment with Physiological Saline (TPS (control group, Blends (TBL, and Structured Lipids (TSL. The control group (TPS received physiological saline solution for 15 days. In TBL, BL1 was administered during the inflammation phase (days 0-3 and BL2 in the tissue formation and remodeling phase (days 4-15. In TSL, Structured Lipid 1 (SL1 and Structured Lipid 2 (SL2 were used instead of BL1 and BL2, respectively. The aim of this study was to compare wound closure evolution among rats treated with the blends or structured lipids versus control rats treated with physiological saline. The wound healing process was evaluated by measuring the wound areas along the treatments and the concentrations of cytokines. An increase in the areas of wounds treated with the blends and structured lipids in the inflammatory phase was observed, followed by a steeper closure curve compared to wounds treated with physiological saline. The changes observed during the inflammatory phase suggest a potential therapeutic application in cutaneous wound healing which should be further investigated.

Enhancement of antioxidative activity and cardiovascular protection in hamsters by camellia oil and soybean-camellia blended oil.

Science.gov (United States)

Chou, Ting-Yi; Lu, Yi-Fa; Inbaraj, Baskaran Stephen; Chen, Bing-Huei

2018-02-07

The aim of this study was to examine the effects of several vegetable oils and blended oil composed of soybean and camellia oils on blood lipid reduction and antioxidative activity. Forty male hamsters were fed an AIN-93 G diet for 1 wk, followed by dividing into five groups: control group-1 was fed a low-fat diet containing 5% oil for 6 wk, and the other four groups were fed high-fat diets with group-2 containing 14% palm oil, group-3 containing 14% camellia oil, group-4 containing 14% soybean oil, and group-5 containing 14% blended oil (8.4% soybean oil and 5.6% camellia oil) along with 0.2% cholesterol and 0.1% bile acid. High-fat diets raised serum triacylglycerol, total cholesterol, and aspartate aminotransferase in hamsters without affecting alanine aminotransferase. Compared with palm oil-containing diet, the other three high-fat diets reduced serum total cholesterol, low-density lipoprotein cholesterol, and the ratio of low-density lipoprotein to high-density lipoprotein cholesterol with an opposite trend for liver total cholesterol. However, compared with the control group, the serum high-density lipoprotein cholesterol level was raised for all four high-fat diets. The higher the degree of oil unsaturation, the higher the serum thiobarbituric acid reactive substances and the lower the liver triacylglycerol level and activities of fatty acid synthase, glucose 6-phosphate dehydrogenase, and malic enzymes. Both soybean and blended oils lowered the antioxidative activity of liver. Camellia and blended oils were more efficient than soybean oil in elevating serum high-density lipoprotein cholesterol and decreasing the ratio of low-density lipoprotein to high-density lipoprotein cholesterol in hamsters. Copyright © 2018 Elsevier Inc. All rights reserved.

Human Milk Fat Substitute Produced by Enzymatic Interesterification of Vegetable Oil Blend

Directory of Open Access Journals (Sweden)

Semra Turan

2007-01-01

Full Text Available Palm oil, palm kernel oil, olive oil, sunflower oil, and marine oil blend, formulated in the mass ratio of 4.0:3.5:1.0:1.5:0.2, was subjected to interesterification catalyzed by lipase from Thermomyces lanuginosa (Lipozyme® TL IM for obtaining a product that contains similar triacylglycerol (TAG structure to that of human milk fat (HMF. Reactions were carried out in a double jacketed glass vessel equipped with magnetic stirrer at 60 °C for 2, 4, 6, 8, 12 and 24 h. The blend was analyzed for fatty acid composition of both total fatty acids and those at the sn-2 position after pancreatic lipase hydrolysis. After interesterification, TAGs were purified by thin layer chromatography and TAG species were determined according to the carbon number (CN by high-temperature gas chromatography. Enzymatic interesterification generated significant differences for all TAG species from CN30 to CN54. Concentrations of some TAG species (CN30, 32, 34, 36, 38, 50, 52 and 54 decreased, while some (CN40 to 48 increased after 24 h. TAG species with higher CN reached maximum levels at the end of 6 h of reaction time. The predominant TAGs of the reaction product after 24 h were CN46, 48, 50, 52 and 54 with ratios of 13.8, 18.2, 13.9, 17.8, and 12.1 %, respectively. These TAG species contain mainly 1,3-diunsaturated-2-saturated structure, like HMF.

Energy value of poultry byproduct meal and animal-vegetable oil blend for broiler chickens by the regression method.

Science.gov (United States)

Cao, M H; Adeola, O

2016-02-01

The energy values of poultry byproduct meal (PBM) and animal-vegetable oil blend (A-V blend) were determined in 2 experiments with 288 broiler chickens from d 19 to 25 post hatching. The birds were fed a starter diet from d 0 to 19 post hatching. In each experiment, 144 birds were grouped by weight into 8 replicates of cages with 6 birds per cage. There were 3 diets in each experiment consisting of one reference diet (RD) and 2 test diets (TD). The TD contained 2 levels of PBM (Exp. 1) or A-V blend (Exp. 2) that replaced the energy sources in the RD at 50 or 100 g/kg (Exp. 1) or 40 or 80 g/kg (Exp. 2) in such a way that the same ratio were maintained for energy ingredients across experimental diets. The ileal digestible energy (IDE), ME, and MEn of PBM and A-V blend were determined by the regression method. Dry matter of PBM and A-V blend were 984 and 999 g/kg; the gross energies were 5,284 and 9,604 kcal/kg of DM, respectively. Addition of PBM to the RD in Exp. 1 linearly decreased (P blend to the RD linearly increased (P blend as follows: IDE = 10,616x + 7.350, r(2) = 0.96; ME = 10,121x + 0.447, r(2) = 0.99; MEn = 10,124x + 2.425, r(2) = 0.99. These data indicate the respective IDE, ME, MEn values (kcal/kg of DM) of PBM evaluated to be 3,537, 3,805, and 3,278, and A-V blend evaluated to be 10,616, 10,121, and 10,124. © 2015 Poultry Science Association Inc.

Straight vegetable oils usage in a compression ignition engine - A review

Energy Technology Data Exchange (ETDEWEB)

Misra, R.D.; Murthy, M.S. [Mechanical Engineering Department, National Institute of Technology, Silchar 788010, Assam (India)

2010-12-15

The ever increasing fossil fuel usage and cost, environmental concern has forced the world to look for alternatives. Straight vegetable oils in compression ignition engine are a ready solution available, however, with certain limitations and with some advantages as reported by many researchers. A comprehensive and critical review is presented specifically pertaining to straight vegetable oils usage in diesel engine. A detailed record of historical events described. Research carried out specifically under Indian conditions and international research work on the usage of straight vegetable oils in the diesel engine is separately reviewed. Many researchers have reported that straight vegetable oils in small percentage blends with diesel when used lower capacity diesel engines have shown great promise with regards to the thermal performance as well exhaust emissions. This has been explained in detail. Finally based on the review of international as well as Indian research a SWOT analysis is carried out. The review concludes that there is still scope for research in this area. (author)

Oxidative stability of diacylglycerol oil and butter blends containing diacylglycerols

DEFF Research Database (Denmark)

Kristensen, Janni Brogaard; Nielsen, Nina Skall; Jacobsen, Charlotte

2006-01-01

Diacylglycerol (DAG) oils produced from sunflower oil and traditional sunflower oil were stored for 20 wk at 38 degrees C, and their oxidative stability was measured. Moreover, two butter blends were produced containing 40 wt-% DAG oil made from sunflower oil or rapeseed oil, respectively, as well...... as two control butter blends with sunflower oil or rapeseed oil. Their oxidative stability during storage at 5 degrees C for up to 12 wk was examined by similar means as for the pure oils. The storage study of the oils indicated that the DAG oil was oxidatively less stable as compared to sunflower oil......, but that they had similar sensory quality. Storage of the butter blends revealed that blends with the two types of rapeseed oil (triacylglycerol (TAG) or DAG oil) were oxidatively more stable than the blends containing oils from sunflower. There was no unambiguous indication of DAG butter blends having a different...

Experimental investigation of a diesel engine with methyl ester of mango seed oil and diesel blends

Directory of Open Access Journals (Sweden)

K. Vijayaraj

2016-03-01

Full Text Available Petroleum based fuels worldwide have not only resulted in the rapid depletion of conventional energy sources, but have also caused severe air pollution. The search for an alternate fuel has led to many findings due to which a wide variety of alternative fuels are available at our disposal now. The existing studies have revealed the use of vegetable oils for engines as an alternative for diesel fuel. However, there is a limitation in using straight vegetable oils in diesel engines due to their high viscosity and low volatility. In the present work, neat mango seed oil is converted into their respective methyl ester through transesterification process. Experiments are conducted using various blends of methyl ester of mango seed oil with diesel in a single cylinder, four stroke vertical and air cooled Kirloskar diesel engine. The experimental results of this study showed that the MEMSO biodiesel has similar characteristics to those of diesel. The brake thermal efficiency, unburned hydrocarbon and smoke density are observed to be lower in case of MEMSO biodiesel blends than diesel. The CO emission for B25, B50 and B75 is observed to be lower than diesel at full load, whereas for B100 it is higher at all loads. On the other hand, BSFC and NOx of MEMSO biodiesel blends are found to be higher than diesel. It is found that the combustion characteristics of all blends of methyl ester of mango seed oil showed similar trends with those of the baseline diesel. From this study, it is concluded that optimized blend is B25 and could be used as a viable alternative fuel in a single cylinder direct injection diesel engine without any modifications.

Quantification of rice bran oil in oil blends

Directory of Open Access Journals (Sweden)

Mishra, R.

2012-03-01

Full Text Available Blends consisting of physically refined rice bran oil (PRBO: sunflower oil (SnF and PRBO: safflower oil (SAF in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil.

Se analizaron diversos parámetros físico-químicos para la evaluación de mezclas de aceites en diferentes proporciones que incluyen: aceite de salvado de arroz físícamente refinado (PRBO: aceite de girasol (SNF y las mezclas PRBO: aceite de cártamo (SAF en diferentes proporciones. La cuantificación de la presencia del aceite de salvado de arroz en las mezclas se llevó a cabo por diferentes métodos, como cromatografía de gases (GC, cromatografía líquida (HPLC, ultrasonidos y métodos basados en otros parámetros f

Eucalyptus-Palm Kernel Oil Blends: A Complete Elimination of Diesel in a 4-Stroke VCR Diesel Engine

Directory of Open Access Journals (Sweden)

Srinivas Kommana

2015-01-01

Full Text Available Fuels derived from biomass are mostly preferred as alternative fuels for IC engines as they are abundantly available and renewable in nature. The objective of the study is to identify the parameters that influence gross indicated fuel conversion efficiency and how they are affected by the use of biodiesel relative to petroleum diesel. Important physicochemical properties of palm kernel oil and eucalyptus blend were experimentally evaluated and found within acceptable limits of relevant standards. As most of vegetable oils are edible, growing concern for trying nonedible and waste fats as alternative to petrodiesel has emerged. In present study diesel fuel is completely replaced by biofuels, namely, methyl ester of palm kernel oil and eucalyptus oil in various blends. Different blends of palm kernel oil and eucalyptus oil are prepared on volume basis and used as operating fuel in single cylinder 4-stroke variable compression ratio diesel engine. Performance and emission characteristics of these blends are studied by varying the compression ratio. In the present experiment methyl ester extracted from palm kernel oil is considered as ignition improver and eucalyptus oil is considered as the fuel. The blends taken are PKE05 (palm kernel oil 95 + eucalyptus 05, PKE10 (palm kernel oil 90 + eucalyptus 10, and PKE15 (palm kernel 85 + eucalyptus 15. The results obtained by operating with these fuels are compared with results of pure diesel; finally the most preferable combination and the preferred compression ratio are identified.

Combustion performance of pyrolysis oil/ethanol blends in a residential-scale oil-fired boiler

Science.gov (United States)

A 40 kWth oil-fired commercial boiler was fueled with blends of biomass pyrolysis oil (py-oil) and ethanol to determine the feasibility of using these blends as a replacement for fuel oil in home heating applications. An optimal set of test parameters was determined for the combustion of these blend...

Absorption difference between diacylglycerol oil and butter blend containing diacylglycerol oil

DEFF Research Database (Denmark)

Kristensen, Janni Brogaard; Jørgensen, Henry; Mu, Huiling

2012-01-01

butter blend (BDAG), triacylglycerol (TAG) butter blend (BTAG), DAG oil (ODAG) or TAG oil (OTAG) were prepared, and each was fed to a group of 8 male Wistar rats. The design of the experiment was a combined balance and feeding experiment. The rats fed the BTAG and ODAG‐diets had a significantly higher......This study aims at investigating whether the intake of butter blends containing diacylglycerol (DAG) oil may result in reduced fat accumulation, in similarity to DAG oil, and the potential metabolic differences between butter blends and DAG oil. Four experimental diets containing either 10 wt% DAG...... protein content than rats fed the BDAG and OTAG‐diets, and the fat content was significantly lower in rats fed the ODAG‐diet as compared to rats fed the OTAG and BDAG‐diets. A significantly higher content of ash was observed in rats fed the two TAG diets. The ratio of abdominal fat weight/body weight...

Vegetable oil spills : oil properties and behaviour

International Nuclear Information System (INIS)

Fingas, M.; Fieldhouse, B.; Jokuty, P.

2001-01-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs

Vegetable oil spills : oil properties and behaviour

Energy Technology Data Exchange (ETDEWEB)

Fingas, M.; Fieldhouse, B.; Jokuty, P. [Environment Canada, Ottawa, ON (Canada). Emergencies Science Div

2001-07-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs.

Replacement of milk fat by mixed vegetable oils in manufacturing soft cheese treated by gamma irradiation

International Nuclear Information System (INIS)

Afifi, E.A.; Anwar, M.M.

2007-01-01

This investigation aimed to study the possibility of substituting milk fat by using blended vegetable oils in manufacturing soft cheese with low salt content, in addition, lo utilize gamma irradiation to prolong the shelf-life of the new manufactured product. Therefore, one hundred (lOOKg) from fresh buffaloes milk containing 5 % milk fal and 3 % salt were divided into tow parts , the first part was used for manufacturing control soft cheese sample (containing milk fat ), while the second part was skimmed, blended with blended vegetable oils and homogenized. The skim homogenized milk containing 5% mixed vegetable oils used for manufacturing soft cheese ( new product filled ). The obtained soft cheese was subjected to 1, 2 and 3 kGy y-irradiation, and stored at refrigerator temperature. During cold storage, the sensory, microbial and chemical properties of control soft cheese and treated one were evaluated. The obtained results indicated that the replacement of milk fat by mixed vegetable oils in the manufacturing soft cheese had no effect on chemical composition and sensory properties except white color and slight oily flavor which have been noticed in treated filled cheese. In addition, irradiation dose of 3 kGy prolonged the shelf-life of treated filled cheese to 42 days compared to 18 days for control sample and scqueiitly, the new product high percentage of iinsaluraled fatly acid and no cholesterol compared with cheese made from natural milk and can be recommended as a healthy food especially for those who need to low or free cholesterol foods

Base catalyzed transesterification of acid treated vegetable oil blend for biodiesel production

Energy Technology Data Exchange (ETDEWEB)

Yusup, Suzana; Khan, Modhar Ali [Chemical Engineering Department, Universiti Teknologi PETRONAS, Seri Iskandar, Tronoh, Perak 31750 (Malaysia)

2010-10-15

Biodiesel can be produced from low cost non-edible oils and fats. However, most of these sources are of high free fatty acid content which requires two stage transesterification to reduce the acid value and produce biodiesel. The acid treatment step is usually followed by base transesterification since the latter can yield higher conversions of methyl esters at shorter reaction time when compared with acid catalyzed reaction. In the current study, base transesterification in the second stage of biodiesel synthesis is studied for a blend of crude palm/crude rubber seed oil that had been characterized and treated with acid esterification. Optimum conditions for the reaction were established and effect of each variable was investigated. The base catalyzed transesterification favored a temperature of 55 C with methanol/oil molar ratio of 8/1 and potassium hydroxide at 2% (ww{sup -1}) (oil basis). The conversion of methyl esters exceeded 98% after 5 h and the product quality was verified to match that for biodiesel with international standards. (author)

21 CFR 133.168 - Pasteurized blended cheese with fruits, vegetables, or meats.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Pasteurized blended cheese with fruits, vegetables... fruits, vegetables, or meats. (a) Pasteurized blended cheese with fruits, vegetables, or meats, or... vegetable; any properly prepared cooked or canned meat. (3) When the added fruits, vegetables, or meats...

A Study of the Use of Jatropha Oil Blends in Boilers

Energy Technology Data Exchange (ETDEWEB)

Krishna, C.R.

2010-10-01

Executive Summary: This project investigated the combustion performance of blends of unrefined Jatropha oil and its blends in laboratory boilers. Although a very limited amount of testing blends in distillate oil, ASTM No. 2 oil or heating oil was conducted, the primary interest was in testing the performance of blends with residual ASTM No. 6 oil. The basic idea is to provide a renewable fuel option to residual oil used in space heating and in industrial applications. The intent also was to explore the use of non-edible plant oil and one that might be potentially cheaper than biodiesel. The characteristics of No. 6 oil, such as high viscosity at ambient temperature, which requires it to be kept heated, make the blending with such oils feasible. Jatropha oil is one such oil and there is currently considerable interest building up in its use as a source for making biodiesel and jet fuel. A 10% blend of Jatropha oil with heating oil was burned using a standard burner in a residential boiler. Combustion performance was shown to be comparable with that of burning heating oil by itself with some noticeable differences. Typical heating oil has about 2000 ppm of sulfur, while the Jatropha oil has about 50 ppm leading to lower levels of sulphur dioxide emissions. Stack measurements also showed that the NOx emission was lower with the blend. We have previously reported similar reductions in NOx with blends of biodiesel in heating oil as well as slight reductions in PM2.5, particulates below 2.5 microns in size. Long term tests were not part of this project and hence deleterious effects on pumps, seals etc., if any, were not measured. The majority of the work involved testing blends of Jatropha oil with residual oil in a 1.5 million Btu/hr boiler with a burner modified to burn residual oil. Blends of 20 and 60% Jatropha oil and 100% Jatropha oil were burned in the combustion performance tests. The residual oil used had a sulfur content of over 2000 ppm and hence dramatic

HVO, hydrotreated vegetable oil. A premium renewable biofuel for diesel engines

Energy Technology Data Exchange (ETDEWEB)

Mikkonen, Seppo [Neste Oil, Porvoo (Finland); Honkanen, Markku; Kuronen, Markku [Neste Oil, Espoo (Finland)

2013-06-01

HVO is renewable paraffinic diesel fuel produced from vegetable oils or animal fats by hydrotreating and isomerization. Composition is similar to GTL. HVO is not ''biodiesel'' which is a definition reserved for FAME. HVO can be used in diesel fuel without any ''blending wall'' as well as in addition to the FAME in EN 590. As a blending component HVO enhances fuel properties thanks to its high cetane, zero aromatics and reasonable distillation range. HVO can be used for upgrading gas oils to meet diesel fuel standard and for producing premium diesel fuels. HVO is comparable to fossil diesel regarding fuel logistics, stability, water separation and microbiological growth. The use of HVO as such or in blends reduces NO{sub x} and particulate emissions. Risks for fuel system deposits and engine oil deterioration are low. Combustion is practically ash-free meaning low risk for exhaust aftertreatment life-time. Winter grade fuels down to -40 C cloud point can be produced by HVO process from many kinds of feedstocks. HVO is fully accepted by directives and fuel standards. (orig.)

Fuel Continuous Mixer ? an Approach Solution to Use Straight Vegetable Oil for Marine Diesel Engines

Directory of Open Access Journals (Sweden)

Đặng Van Uy

2018-03-01

Full Text Available The vegetable oil is well known as green fuel for diesel engines due to its low sunphur content and renewable stock. However, there are some problems raising when vegetable oil is used as fuel for diesel engines such as highly effected by cold weather, lower general efficiency, separation in layer if mixed with diesel oil and so on. To overcome that disadvantiges, the authors propose a new idea that to use a continuous fuel mixer to blend vegetable oil with diesel oil to make so called a mixed fuel supplying to diesel engines inline. In order to ensure a quality of the mixed fuel created by continuous mixer, a homogeneous testing was introduced with believable results. Then, the continuous mixer has been installed into fuel supply system of diesel engine 6LU32 at a lab of Vietnam Maritime University in terms of checking a real operation of the fuel continuous mixer with diesel engine.

Analytical characterization of pure and blended watermelon (citrullus lanatus) oil: impact of blending on oxidative stability

International Nuclear Information System (INIS)

Azeem, M.W.; Nadeem, M.

2015-01-01

Analytical characterization of pure, blended watermelon (Citrulluslanatus) oil and impact of blending on oxidative stability was investigated. Watermelon oil was added with mango (Mangiferaindica L.) kernel oil at four different concentrations 5, 10, 15 and 20% (B 1, B2, B3 and B4) and referenced with a control (100% watermelon oil). All the blends were stored in transparent PET bottles at ambient temperature (25-28 degree C) for 3 months; storage stability was assessed at the interval of 1 month. Free fatty acid, unsaponifiable matter, saponification value, refractive index and iodine value of watermelon seed oil and mango kernel oil was 1.38%, 0.34%; 0.71%, 1.68%; 198, 193; 1.468, 1.457; 107.51, 54.62, respectively. The tocopherol content of watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 127.49, 205.44, 135.24, 144.52, 156.81 and 169.34 mg/kg. delta tocopherol in watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 55.26, 34.81, 53.64, 51.27, 50.14 and 48.23 mg/kg. Concentration of linoleic acid decreased from 50.78% to 30.17% when 40% mango kernel oil was added to watermelon oil. Oleic acid increased from 22.89% in watermelon oil to 25.19%, 28.84% and 30.64% in B1, B2, B3 and B4. The increase in peroxide value of watermelon oil, B1, B2, B3 and B4 was 10.07, 9.56, 7.62, 5.17 and 2.87 (meqO/sub 2//kg) in a time dependent manner. Induction period of pure watermelon oil was less than mango kernel oil and blends. These results suggest that chemical characteristics and oxidative stability of pure watermelon oil can be improved by blending with mango kernel oil. (author)

Analytical Characterization of Pure and Blended Watermelon (Citrullus lanatus oil: Impact of Blending on Oxidative Stability

Directory of Open Access Journals (Sweden)

Muhammad Waqar Azeem

2015-06-01

Full Text Available Analytical characterization of pure, blended watermelon (Citrulluslanatus oil and impact of blending on oxidative stability was investigated. Watermelon oil was added with mango (Mangiferaindica L. kernel oil at four different concentrations 5, 10, 15 and 20% (B1, B2, B3 and B4 and referenced with a control (100% watermelon oil. All the blends were stored in transparent PET bottles at ambient temperature (25-28oC for 3 months; storage stability was assessed at the interval of 1 month. Free fatty acid, unsaponifiable matter, saponification value, refractive index and iodine value of watermelon seed oil and mango kernel oil was 1.38%, 0.34%; 0.71%, 1.68%; 198, 193; 1.468, 1.457; 107.51, 54.62, respectively. The α tocopherol content of watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 127.49, 205.44, 135.24, 144.52, 156.81 and 169.34 mg/kg. δ tocopherol in watermelon oil, mango kernel oil, B1, B2, B3 and B4 was 55.26, 34.81, 53.64, 51.27, 50.14 and 48.23 mg/kg. Concentration of linoleic acid decreased from 50.78% to 30.17% when 40% mango kernel oil was added to watermelon oil. Oleic acid increased from 22.89% in watermelon oil to 25.19%, 28.84% and 30.64% in B1, B2, B3 and B4. The increase in peroxide value of watermelon oil, B1, B2, B3 and B4 was 10.07, 9.56, 7.62, 5.17 and 2.87 (meqO2/kg in a time dependent manner. Induction period of pure watermelon oil was less than mango kernel oil and blends. These results suggest that chemical characteristics and oxidative stability of pure watermelon oil can be improved by blending with mango kernel oil.

BIODIESEL BLENDS IN SPACE HEATING EQUIPMENT

International Nuclear Information System (INIS)

KRISHNA, C.R.

2001-01-01

Biodiesel is a diesel-like fuel that is derived from processing vegetable oils from various sources, such as soy oil, rapeseed or canola oil, and also waste vegetable oils resulting from cooking use. Brookhaven National laboratory initiated an evaluation of the performance of blends of biodiesel and home heating oil in space heating applications under the sponsorship of the Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL). This report is a result of this work performed in the laboratory. A number of blends of varying amounts of a biodiesel in home heating fuel were tested in both a residential heating system and a commercial size boiler. The results demonstrate that blends of biodiesel and heating oil can be used with few or no modifications to the equipment or operating practices in space heating. The results also showed that there were environmental benefits from the biodiesel addition in terms of reductions in smoke and in Nitrogen Oxides (NOx). The latter result was particularly surprising and of course welcome, in view of the previous results in diesel engines where no changes had been seen. Residential size combustion equipment is presently not subject to NOx regulation. If reductions in NOx similar to those observed here hold up in larger size (commercial and industrial) boilers, a significant increase in the use of biodiesel-like fuel blends could become possible

The flexfuel tractor. Invesigations on the combustion behaviour of vegetable oil fuels and on the discernability of fossil and biogenic fuels; Der Flexfuel Traktor. Untersuchungen zum Verbrennungsverhalten von Pflanzenoelkraftstoffen und zur Unterscheidbarkeit fossiler und biogener Kraftstoffe

Energy Technology Data Exchange (ETDEWEB)

Dieringer, Stefanie

2012-07-01

Increasing energy prices, especially for fossil fuels, as well as the necessity to reduce CO{sub 2} emissions are emphasizing the advantages of self-produced vegetable oil fuels in agriculture. Monetary advantages are depending on basic conditions like farm size or tax legislation, which can be changing locally as well as temporarily. Due to the differing properties of diesel and vegetable oil fuel, engines have to be adapted to each fuel to fulfil performance requirements as well as emission limits and reliability. Knowing that there are advantages of vegetable oil compared to diesel fuel, though not always and everywhere present, it becomes obvious that the well known flexible fuel concept of passenger cars should be adapted for diesel engines of agricultural machines. So called flexfuel engines imply the detection of the fuel type and an automated adjustment of the engine control parameters without any manual action of an operator. Therefore, the first step consists of the evaluation of the combustion properties of rapeseed, sunflower, jatropha and false flax oil compared to diesel fuel. The tested vegetable oils showed very similar behaviour in the tested common rail diesel engine. Especially the limited emissions were met with the same engine control software with all vegetable oils. In consequence it is possible to realize a flexfuel engine using the two engine control maps available at the moment, one for diesel and the other one for vegetable oil fuels. For further investigations one oil type, namely rapeseed oil was selected to test the combustion behaviour of fuel blends made of diesel and vegetable oil. The goal was to determine the blend ratio of vegetable oil and diesel fuel at which the engine control software has to be changed from the diesel to the vegetable oil map automatically. If the fuel consists of 40% or more vegetable oil, the vegetable oil engine control map has to be selected in order to fulfil legal emission limits. Finally the

An Experimental Investigation on Performance and Emissions Characteristics of Jatropha Oil Blends with Diesel in a Direct Injection Compression Ignition Engine

Science.gov (United States)

De, B.; Bose, P. K.; Panua, R. S.

2012-07-01

Continuous effort to reducing pollutant emissions, especially smoke and nitrogen oxides from internal combustion engines, have promoted research for alternative fuels. Vegetable oils, because of their agricultural origin and due to less carbon content compared to mineral diesel are producing less CO2 emissions to the atmosphere. It also reduces import of petroleum products. In the present contribution, experiments were conducted using Jatropha oil blends with diesel to study the effect on performance and emissions characteristics of a existing diesel engine. In this study viscosity of Jatropha oil was reduced by blending with diesel. A single cylinder, four stroke, constant speed, water cooled, diesel engine was used. The results show that for lower blend concentrations various parameters such as thermal efficiency, brake specific fuel consumption, smoke opacity, CO2, and NO x emissions are acceptable compared to that of mineral diesel. But, it was observed that for higher blend concentrations, performance and emissions were much inferior compared to diesel.

Tough Blends of Polylactide and Castor Oil

Energy Technology Data Exchange (ETDEWEB)

Robertson, Megan L.; Paxton, Jessica M.; Hillmyer, Marc A. (UMM)

2012-10-10

Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of L-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized - an order of magnitude larger than that of neat PLLA.

Tough blends of polylactide and castor oil.

Science.gov (United States)

Robertson, Megan L; Paxton, Jessica M; Hillmyer, Marc A

2011-09-01

Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of l-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized-an order of magnitude larger than that of neat PLLA.

Formulation of Zero-Trans Crystalized Fats Produced from Palm Stearin and High Oleic Safflower Oil Blends

Directory of Open Access Journals (Sweden)

Nydia E. Buitimea-Cantúa

2017-01-01

Full Text Available High intake of trans fat is associated with several chronic diseases such as cardiovascular disease and cancer. Fat blends, produced by direct blending process of palm stearin (PS with high oleic safflower oil (HOSO in different concentrations, were investigated. The effects of the PS addition (50, 70, or 90% and the rate of agitation (RA (1000, 2000, or 3000 rpm on physical properties, fatty acid profile (FAP, trans fatty acids (TFA, crystal structure, and consistency were researched. The blend containing 50% of each sort of oil (50% PS/50% HOSO showed that melting point and features were similar to the control shortening. The saturated fatty acids (SFA were higher followed by monounsaturated (MUFA and polyunsaturated fatty acids (PUFA. Significant differences in the content of palmitic and oleic acids among blends were observed. The 50% PS/50% HOSO blend contained higher oleic acid (42.9% whereas the 90% PS/10% HOSO was higher in palmitic acid (56.9%. The blending of PS/HOSO promoted the β crystal polymorphic forms. The direct blending process of equal amounts of PS and HOSO was an adequate strategy to formulate a new zero-trans crystallized vegetable fats with characteristics similar to commercial counterparts with well-balanced fats rich in both omega 3 and omega 6 fatty acids.

Performance and Combustion Characteristics Analysis of Multi-Cylinder CI Engine Using Essential Oil Blends

Directory of Open Access Journals (Sweden)

S. M. Ashrafur Rahman

2018-03-01

Full Text Available Essential oils are derived from not-fatty parts of plants and are mostly used in aromatherapy, as well as cosmetics and perfume production. The essential oils market is growing rapidly due to their claimed health benefits. However, because only therapeutic grade oil is required in the medicinal sector, there is a substantial low-value waste stream of essential oils that can be used in the transportation and agricultural sectors. This study investigated the influence of orange, eucalyptus, and tea tree oil on engine performance and combustion characteristics of a multi-cylinder compression ignition engine. Orange, eucalyptus, and tea tree oil were blended with diesel at 10% by volume. For benchmarking, neat diesel and 10% waste cooking biodiesel-diesel blend were also tested. The selected fuels were used to conduct engine test runs with a constant engine speed (1500 RPM (revolutions per minute at four loads. As the load increased, frictional power losses decreased for all of the fuel samples and thus mechanical efficiency increased. At higher loads (75% and 100%, only orange oil-diesel blends produced comparable power to diesel and waste cooking biodiesel-diesel blends. Fuel consumption (brake and indicated for the essential oil-diesel blends was higher when compared to base diesel and waste cooking biodiesel-diesel blends. Thermal efficiency for the essential oil-diesel blends was comparable to base diesel and waste cooking biodiesel-diesel blends. At higher loads, blow-by was lower for essential oil blends as compared to base diesel and waste cooking biodiesel-diesel blends. At 50% and 100% load, peak pressure was lower for all of the essential oil-diesel blends when compared to base diesel and waste cooking biodiesel-diesel blends. From the heat release rate curve, the essential oil-diesel blends ignition delay times were longer because the oils have lower cetane values. Overall, the low-value streams of these essential oils were found to be

Experimental studies on the combustion and emission characteristics of a diesel engine fuelled with used cooking oil methyl ester and its diesel blends

Energy Technology Data Exchange (ETDEWEB)

Lakshmi Narayana Rao, G.; Sampath, S. [Sri Venkateswara College of Engineering, Sriperumbudur (India); Rajagopal, K. [Jawaharlal Nehru Technological Univ., Hyderabad (India)

2008-04-01

Transesterified vegetable oils (biodiesel) are promising alternative fuel for diesel engines. Used vegetable oils are disposed from restaurants in large quantities. But higher viscosity restricts their direct use in diesel engines. In this study, used cooking oil was dehydrated and then transesterified using an alkaline catalyst. The combustion, performance and emission characteristics of Used Cooking oil Methyl Ester (UCME) and its blends with diesel oil are analyzed in a direct injection C.I. engine. The fuel properties and the combustion characteristics of UCME are found to be similar to those of diesel. A minor decrease in thermal efficiency with significant improvement in reduction of particulates, carbon monoxide and unburnt hydrocarbons is observed compared to diesel. The use of transesterified used cooking oil and its blends as fuel for diesel engines will reduce dependence on fossil fuels and also decrease considerably the environmental pollution. Of the various alternate fuels under consideration, biodiesel is the most promising due to the following reasons: (1) Biodiesel can be used in the existing engine without any modifications. (2) Biodiesel is made entirely from vegetable sources; it does not contain any sulfur, aromatic hydrocarbons, metals or crude oil residues. (3) Biodiesel is an oxygenated fuel; emissions of carbon monoxide and soot tend to reduce. (4) Unlike fossil fuels, the use of biodiesel does not contribute to global warming as CO{sub 2} emitted is once again absorbed by the plants grown for vegetable oil/biodiesel production. Thus CO{sub 2} balance is maintained. (5) The Occupational Safety and Health Administration classifies biodiesel as a non-flammable liquid. (6) The use of biodiesel can extend the life of diesel engines because it is more lubricating than petroleum diesel fuel. (7) Biodiesel is produced from renewable vegetable oils/animal fats and hence improves the fuel or energy security and economy independence.

Oxidative stability, chemical composition and organoleptic properties of seinat (Cucumis melo var. tibish) seed oil blends with peanut oil from China.

Science.gov (United States)

Siddeeg, Azhari; Xia, Wenshui

2015-12-01

Seinat seed oil was blended with peanut oil for the enhancement of stability and chemical characteristics of the blend. The physicochemical properties (relative density, refractive index, free fatty acids, saponification value, iodine value and peroxide value) of seinat seed and peanut oil blends in ratios 95:5, 85:15, 30:70 and 50:50 proportions were evaluated, as well as oxidative stability index, deferential scanning calorimetric (DSC) characteristics and tocopherols content. Results of oil blend showed that there was no negative effect by the addition of seinat seed oil to peanut oil and also had decreased percentages of all saturated fatty acids except stearic acid, conversely, increased the levels of unsaturated fatty acids. As for the sensory evaluation, the panelist results showed that seinat seed oil blends had no significant differences (p blending of seinat seed oil with peanut oil had also increased the stability and tocopherols content. As Sudan is the first producer of seinat oil, blending of seinat seed oil with traditional oil like quality, and may decrease the consumption of other expensive edible oils.

Improving oxidative stability of liquid fish oil supplements for pets

DEFF Research Database (Denmark)

Thomsen, Birgitte Raagaard; Griinari, Mikko; Jacobsen, Charlotte

2017-01-01

oxidative stability to the same extent as 2000 ppm mixed tocopherols in Oxipres. Overall, oxidative stability of fish oil or fish oil + vegetable oil blends was improved the most by addition of 5000 ppm rosemary extract and 500 ppm mixed tocopherols. A commercial oil blend with composition optimized based...... of fish oil by adding vegetable oils, mixed tocopherols and rosemary extract, and to formulate a commercial product according to the results obtained. The formulated product was evaluated against commercial fish oil products. An initial screening for antioxidative effect was performed by using Oxipres...... equipment. The effect of antioxidant and vegetable oil blends was examined in oils stored at 30 and 40°C by measuring peroxide value, volatile compounds with GC-MS and tocopherol content. Addition of vegetable oil and rosemary extract at high level (4000–6000 ppm) plus 600 ppm of mixed tocopherols increased...

Solids precipitation in crude oils, gas-to-liquids and their blends

Science.gov (United States)

Ramanathan, Karthik

Gas-to-liquids (GTL) liquids are obtained from syngas by the Fischer-Tropsch synthesis. The blending of GTL liquids produced from natural gas/coal reserves and crude oils is a possibility in the near future for multiple reasons. Solids precipitation is a major problem in pipelines and refineries leading to significant additional operating costs. The effect of the addition of a paraffinic GTL liquid to crude oils on solids precipitation was investigated in this study. A Fourier transform infrared (FT-IR) spectroscopic technique was used to obtain solid-liquid equilibria (SLE) data for the various samples. The SLE of multiple systems of model oils composed of n-alkanes was investigated preliminarily. Blends of a model oil simulating a GTL liquid composition and a crude oil showed that the wax precipitation temperature (WPT) decreased upon blending. Three crude oils from different geographic regions (Alaskan North Slope, Colorado and Venezuela) and a laboratory-produced GTL liquid were used in the preparation of blends with five different concentrations of the GTL liquid. The wax precipitation temperatures of the blends were found to decrease with the increasing addition of the GTL liquid for all the oils. This effect was attributed to the solvent effect of the low molecular weight-paraffinic GTL liquid on the crude oils. The weight percent solid precipitated that was estimated as a function of temperature did not show a uniform trend for the set of crude oils. The asphaltene onset studies done on the blends with near-infrared spectroscopy indicated that the addition of GTL liquid could have a stabilizing effect on the asphaltenes in some oils. Analytical techniques such as distillation, solvent separation, HPLC, GC, and GPC were used to obtain detailed composition data on the samples. Two sets of compositional data with 49 and 86 pseudo-components were used to describe the three crude oils used in the blending work. The wax precipitation was calculated using a

Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends

Energy Technology Data Exchange (ETDEWEB)

Altiparmak, D.; Keskin, A.; Koca, A. [Gazi University, Ankara (Turkey). Technical Education Faculty; Guru, M. [Gazi University, Ankara (Turkey). Engineering and Architectural Faculty

2007-01-15

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load conditions. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO{sub x} emissions increased up to 30% with the new fuel blends. The smoke capacity did not vary significantly. (author)

Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends.

Science.gov (United States)

Altiparmak, Duran; Keskin, Ali; Koca, Atilla; Gürü, Metin

2007-01-01

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load condition. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO(x) emissions increased up to 30% with the new fuel blends. The smoke opacity did not vary significantly.

Performance of jatropha oil blends in a diesel engine

Energy Technology Data Exchange (ETDEWEB)

Forson, F.K.; Oduro, E.K.; Hammond-Donkoh, E. [Kwame Nkrumah University of Science and Technology, Kumasi (Ghana). Dept. of Mechanical Engineering

2004-06-01

Results are presented on tests on a single-cylinder direct-injection engine operating on diesel fuel, jatropha oil, and blends of diesel and jatropha oil in proportions of 97.4%/2.6%; 80%120%; and 50%150% by volume. The results covered a range of operating loads on the engine. Values are given for the chemical and physical properties of the fuels, brake specific fuel consumption, brake power, brake thermal efficiency, engine torque, and the concentrations of carbon monoxide, carbon dioxide and oxygen in the exhaust gases. Carbon dioxide emissions were similar for all fuels, the 97.4% diesel/2.6% jatropha fuel blend was observed to be the lower net contributor to the atmospheric level. The trend of carbon monoxide emissions was similar for the fuels but diesel fuel showed slightly lower emissions to the atmosphere. The test showed that jatropha oil could be conveniently used as a diesel substitute in a diesel engine. The test further showed increases in brake thermal efficiency, brake power and reduction of specific fuel consumption for jatropha oil and its blends with diesel generally, but the most significant conclusion from the study is that the 97.4% diesel/2.6% jatropha fuel blend produced maximum values of the brake power and brake thermal efficiency as well as minimum values of the specific fuel consumption. The 97.4%12.6% fuel blend yielded the highest cetane number and even better engine performance than the diesel fuel suggesting that jatropha oil can be used as an ignition- accelerator additive for diesel fuel. (author)

Use of crude filtered vegetable oil as a fuel in diesel engines state of the art: Literature review

Energy Technology Data Exchange (ETDEWEB)

Sidibe, S.S.; Azoumah, Y. [Institut Internationale d' ingenierie de l' Eau et de l' Environnement (2iE), rue de science 01 Ouagadougou 01 BP 594 (Burkina Faso); Blin, J. [Institut Internationale d' ingenierie de l' Eau et de l' Environnement (2iE), rue de science 01 Ouagadougou 01 BP 594 (Burkina Faso); Centre International de Recherche Agronomique pour le Developpement (CIRAD), UPR Biomasse energie, TA B-42/16, 73 rue JF Breton, 34398 Montpellier Cedex 5 (France); Vaitilingom, G. [Centre International de Recherche Agronomique pour le Developpement (CIRAD), UPR Biomasse energie, TA B-42/16, 73 rue JF Breton, 34398 Montpellier Cedex 5 (France)

2010-12-15

Many studies have been published on vegetable oil use in diesel engines. The different authors unanimously acknowledge the potential and merits of this renewable fuel. Typically, Straight Vegetable Oils (SVOs) produced locally on a small scale, have proven to be easy to produce with very little environmental impact. However, as their physico-chemical characteristics differ from those of diesel oil, their use in diesel engines can lead to a certain number of technical problems over time. In bibliography, there is substantial disagreement between authors regarding the advanced phenomena linked to this problems and the recommended solutions. Some of these publications treat options individually without any real comparison between them. Another observation is that the literature rarely tackles problems linked to vegetable oil quality. This paper sets out to review the state of the art for SVO use as fuel in diesel engines, based on a bibliographic study (literature review). The first section of the document examines the influence of the type and quality of vegetable oils for fuel use in diesel engines. The second section discusses the advantages and disadvantages of two options recommended for SVO use in diesel engines: dual fuelling and blending with diesel fuel. (author)

Performance of the mineral blended ester oil-based drilling fluid systems

Energy Technology Data Exchange (ETDEWEB)

Ismail, A.R.; Kamis, A.; Foo, K.S. [University Teknologi (Malaysia)

2001-06-01

A study was conducted in which the properties of ester oil-based drilling fluid systems were examined using a blended mixture of ester and synthetic mineral oil. Biodegradable invert emulsion ester-based fluids are preferred over mineral oil-based drilling fluids for environmental reasons, but they tend to cause alkaline hydrolysis resulting in solidification of the drilling fluid systems. The drilling fluid examined here consisted of Malaysian palm oil ester derivatives (methyl laureate ester or isopropyl laureate ester) blended with commercially available synthetic mineral oil. This mineral oil was added to reduce the problem of alkaline hydrolysis. This mixture, however, was found to be unstable and could not solve the problem at high temperature. The isopropyl laureate and mineral oil blended system was more stable towards the hydrolysis process up to 250 degrees F. In order to enhance the performance of an invert emulsion drilling fluid system, it was recommended that brine water content of the fluid system be lowered. 3 refs., 2 figs.

Waste vegetable oil survey report

Energy Technology Data Exchange (ETDEWEB)

MacLeod, R. [Science enterprise Algoma seA, Sault Ste. Marie, ON (Canada)

2009-02-06

This study was conducted to estimate potential sources of feedstock waste oils for biodiesel production in the Sault Ste. Marie region of Ontario. Two feedstocks were investigated over a period of several months, notably cooking oil and waste vegetable oil. The study was conducted to examine oil throughput, collection practices, and to gauge interest in local initiatives. A distribution list of commercial restaurant listings was developed, and surveys were conducted with members of private enterprises, city government, and non-profit stakeholders in the region. Average volumes of waste vegetable oil were presented for different types of restaurants. The various types of oil used in the restaurants were also quantified. Results of the study showed a positive public response to the idea of a local biodiesel initiative. Steak house, fast food, and Italian establishments generated the largest portion of waste vegetable oil amongst survey respondents. However, the highest response rates came from establishments with little or no oil consumption. Many franchise fast food restaurants are already in contracts with waste oil removal companies. 3 tabs., 3 figs.

Effects of Chemical Inter esterification on the Physicochemical Properties of Palm Stearin, Palm Kernel Oil and Soybean Oil Blends

International Nuclear Information System (INIS)

Siti, M. F.H.; Norizzah, A. R.; Zaliha, O.

2012-01-01

Palm stearin (PS), palm kernel oil (PKO) and soybean oil (SBO) blends were formulated according to Design Expert 8.0.4 (2010). All the sixteen oil blends were subjected to chemical inter esterification (CIE) using sodium methoxide as the catalyst. The effects of chemical inter esterification on the slip melting point (SMP), solid fat content (SFC), triacylglycerol (TAG) composition and polymorphism were investigated. Palm based trans-free table margarine containing PS/PKO/SBO [49/20/31, (w/w)], was optimally formulated through analysis of multiple ternary phase diagrams and was found to have quite similar SMP and SFC profiles as compared with commercial table margarine. This study has shown that blending and chemical inter esterification are effective in modifying the physicochemical properties of palm stearin, palm kernel oil, soybean oil and their blends. (author)

An Investigation into the Physico-chemical Properties of Transformer Oil Blends with Antioxidants extracted from Turmeric Powder

Science.gov (United States)

Dukhi, Veresha; Bissessur, Ajay; Ngila, Catherine Jane; Ijumba, Nelson Mutatina

2013-07-01

The blending of transformer oil (used mainly as an insulating oil) with appropriate synthetic antioxidants, such as BHT (2,6-di-tert-butyl-4-methylphenol) and DBP (2,6-di-tert-butylphenol) have been previously reported. This article is focused on the use of antioxidant extracts from turmeric (Curcuma longa), a natural source. Turmeric is well known for its antimicrobial, antioxidant and anticarcinogenic properties owing to the active nature of its components. Extracts from powdered turmeric were subsequently blended into naphthenic-based uninhibited virgin transformer oil, hereinafter referred to as extract-oil blends (E-OB). Thin-layer chromatography (TLC) of the oil blends revealed that five components extracted from turmeric powder were successfully blended into the oil. Subsequent gas chromatography-mass spectrometry (GC-MS) analysis confirmed the presence of the compounds: curcumene, sesquiphellandrene, ar-turmerone, turmerone and curlone. Thermogravimetric analysis (TGA) of the extract-oil blends, containing various levels of extracts, revealed an average temperature shift of ˜8.21°C in the initial onset of degradation in comparison to virgin non-blended oil. The 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay showed that an increase in the mass aliquot of turmeric extracts in the transformer oil increased the free radical scavenging activity of the oil. Electrical properties of the oil investigated showed that the dissipation factor in the blended oil was found to be lower than that of virgin transformer oil. Evidently, a lower dissipation value renders the oil blend as a superior insulator over normal virgin non-blended oil. This investigation elucidated improved physico-chemical properties of transformer oil blended with turmeric antioxidant extracts.

COMBUSTION CHARACTERISTICS OF DIESEL ENGINE OPERATING ON JATROPHA OIL METHYL ESTER

Directory of Open Access Journals (Sweden)

Doddayaraganalu Amasegoda Dhananjaya

2010-01-01

Full Text Available Fuel crisis because of dramatic increase in vehicular population and environmental concerns have renewed interest of scientific community to look for alternative fuels of bio-origin such as vegetable oils. Vegetable oils can be produced from forests, vegetable oil crops, and oil bearing biomass materials. Non-edible vegetable oils such as jatropha oil, linseed oil, mahua oil, rice bran oil, karanji oil, etc., are potentially effective diesel substitute. Vegetable oils have reasonable energy content. Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in diesel engines with very little or no engine modifications. This is because it has combustion characteristics similar to petroleum diesel. The current paper reports a study carried out to investigate the combustion, performance and emission characteristics of jatropha oil methyl ester and its blend B20 (80% petroleum diesel and 20% jatropha oil methyl ester and diesel fuel on a single-cylinder, four-stroke, direct injections, water cooled diesel engine. This study gives the comparative measures of brake thermal efficiency, brake specific energy consumption, smoke opacity, HC, NOx, ignition delay, cylinder peak pressure, and peak heat release rates. The engine performance in terms of higher thermal efficiency and lower emissions of blend B20 fuel operation was observed and compared with jatropha oil methyl ester and petroleum diesel fuel for injection timing of 20° bTDC, 23° bTDC and 26° bTDC at injection opening pressure of 220 bar.

Using of cotton oil soapstock biodiesel-diesel fuel blends as an alternative diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Keskin, Ali [Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey); Aydin, Kadir [Engineering and Architectural Faculty, Cukurova University, 01330 Adana (Turkey)

2008-04-15

In this study, usability of cotton oil soapstock biodiesel-diesel fuel blends as an alternative fuel for diesel engines were studied. Biodiesel was produced by reacting cotton oil soapstock with methyl alcohol at determined optimum condition. The cotton oil biodiesel-diesel fuel blends were tested in a single cylinder direct injection diesel engine. Engine performances and smoke value were measured at full load condition. Torque and power output of the engine with cotton oil soapstock biodiesel-diesel fuel blends decreased by 5.8% and 6.2%, respectively. Specific fuel consumption of engine with cotton oil soapstock-diesel fuel blends increased up to 10.5%. At maximum torque speeds, smoke level of engine with blend fuels decreased up to 46.6%, depending on the amount of biodiesel. These results were compared with diesel fuel values. (author)

Using of cotton oil soapstock biodiesel-diesel fuel blends as an alternative diesel fuel

International Nuclear Information System (INIS)

Keskin, Ali; Guerue, Metin; Altiparmak, Duran; Aydin, Kadir

2008-01-01

In this study, usability of cotton oil soapstock biodiesel-diesel fuel blends as an alternative fuel for diesel engines were studied. Biodiesel was produced by reacting cotton oil soapstock with methyl alcohol at determined optimum condition. The cotton oil biodiesel-diesel fuel blends were tested in a single cylinder direct injection diesel engine. Engine performances and smoke value were measured at full load condition. Torque and power output of the engine with cotton oil soapstock biodiesel-diesel fuel blends decreased by 5.8% and 6.2%, respectively. Specific fuel consumption of engine with cotton oil soapstock-diesel fuel blends increased up to 10.5%. At maximum torque speeds, smoke level of engine with blend fuels decreased up to 46.6%, depending on the amount of biodiesel. These results were compared with diesel fuel values. (author)

[Determination of olive oil content in olive blend oil by headspace gas chromatography-mass spectrometry].

Science.gov (United States)

Jiang, Wanfeng; Zhang, Ning; Zhang, Fengyan; Yang, Zhao

2017-07-08

A method for the determination of the content of olive oil in olive blend oil by headspace gas chromatography-mass spectrometry (SH-GC/MS) was established. The amount of the sample, the heating temperature, the heating time, the amount of injection, the injection mode and the chromatographic column were optimized. The characteristic compounds of olive oil were found by chemometric method. A sample of 1.0 g was placed in a 20 mL headspace flask, and heated at 180℃ for 2700 s. Then, 1.0 mL headspace gas was taken into the instrument. An HP-88 chromatographic column was used for the separation and the analysis was performed by GC/MS. The results showed that the linear range was 0-100%(olive oil content). The linear correlation coefficient ( r 2 ) was more than 0.995, and the limits of detection were 1.26%-2.13%. The deviations of olive oil contents in the olive blend oil were from -0.65% to 1.02%, with the relative deviations from -1.3% to 6.8% and the relative standard deviations from 1.18% to 4.26% ( n =6). The method is simple, rapid, environment friendly, sensitive and accurate. It is suitable for the determination of the content of olive oil in olive blend oil.

Effects of blending composition of tung oil and ultrasonic irradiation intensity on the biodiesel production

International Nuclear Information System (INIS)

Manh, Do-Van; Chen, Yi-Hung; Chang, Chia-Chi; Chang, Ching-Yuan; Hanh, Hoang-Duc; Chau, Nguyen-Hoai; Tuyen, Trinh-Van; Long, Pham-Quoc; Minh, Chau-Van

2012-01-01

The beneficial use of tung oil in pre-blended oil for the production of biodiesel was studied at various blending compositions of tung, canola and palm oils (C BT , C BC and C BP ). The effects of C BT , ultrasonic power (P WUS ) and sample loading (V L ) on the yield (Y F ) and the properties of acid value, iodine values (IV), kinematic viscosity (KV), density and cold filter plugging point (CFPP) were investigated. The pre-blending of tung oil with palm oil greatly decreases the CFPP of palm oil biodiesel, whereas the presence of canola and palm oils with tung oil reduces the IV and KV of tung oil biodiesel. For P WUS /V L = 0.92–2.08 W/mL, C BT can be as high as 60 wt.% with 30 wt.% C BC and 10 wt.% C BP to produce biodiesel with high Y F and satisfactory qualities of the said properties. -- Highlights: ► Yield and properties of tung oil biodiesel are improved as tung oil is pre-blended with canola and palm oils. ► Pre-blending of palm oil with tung and canola oils reduces the CFPP of palm oil biodiesel from 13 to −5 °C. ► A beneficial use of tung oil as high as 60 wt.% blended with canola and palm oils is achievable. ► A sufficient P WUS per sample volume is required to ensure satisfactory properties.

Blending of palm oil, palm stearin and palm kernel oil in the preparation of table and pastry margarine.

Science.gov (United States)

Norlida, H M; Md Ali, A R; Muhadhir, I

1996-01-01

Palm oil (PO ; iodin value = 52), palm stearin (POs1; i.v. = 32 and POs2; i.v. = 40) and palm kernel oil (PKO; i.v. = 17) were blended in ternary systems. The blends were then studied for their physical properties such as melting point (m.p.), solid fat content (SFC), and cooling curve. Results showed that palm stearin increased the blends melting point while palm kernel oil reduced it. To produce table margarine with melting point (m.p.) below 40 degrees C, the POs1 should be added at level of pastry margarine.

Experimental evaluation of C.I. engine performance using diesel blended with Jatropha biodiesel

Energy Technology Data Exchange (ETDEWEB)

Kumar, Sunil [Mechanical Department, R. G. P. V. Bhopal (M.P.) (India); Chaube, Alok [Mechanical Department, Jabalpur Engineering College Jabalpur (M.P.) (India); Jain, Shashi Kumar [School of Energy and Environment Management, R.G.P.V. Bhopal (India)

2012-07-01

Costlier and depleting fossil fuels are prompting researchers to use edible as well as non-edible vegetable oils as promising alternative to petro-diesel. The higher viscosity of vegetable oils leads to problem in pumping, atomization and spray characteristics. The improper mixing of vegetable oils with air leads to incomplete combustion. The best way to use vegetable oils as fuel in compression ignition (CI) engines is to convert it into biodiesel. Biodiesel is a methyl or ethyl ester of fatty acids made from vegetable oils (both edible and non-edible) and animal fat. The main feedstock for biodiesel production can be non-edible oil obtained from Jatropha curcas plant. Jatropha curcas plant can be cultivated on different terrains in India under extreme climatic conditions. Biodiesel can be used in its pure form or as a blend with petro-diesel in different proportions. It is being used in CI engines because it has properties similar to petro-diesel. The aim of this paper is to analyze suitability of petro-diesel blended with biodiesel in varying proportions in CI engines. For this purpose, a stationary single-cylinder four-stroke CI engine was tested with diesel blended with Jatropha biodiesel in 0%, 5%, 20%, 50%, 80% and 100%. Comparative measures of specific fuel consumption (SFC), brake thermal efficiency, smoke opacity, HC, CO2, CO, O2, NOX have been presented and discussed. Engine performance in terms of comparable brake thermal efficiency and SFC with lower emissions (HC, CO2, CO) was observed with B20 fuel compared to petro-diesel. Volumetric efficiency showed almost no variation for all the blends. Important observations related to noise and vibrations during testing have also been discussed.

The Improvement of Screening the Significant Factors of Oil Blends as Bio lubricant Base Stock

International Nuclear Information System (INIS)

Noor Hajarul Ashikin Shamsuddin; Rozaini Abdullah; Zainab Hamzah; Siti Jamilah Hanim Mohd Yusof

2015-01-01

A new formulation bio lubricant base stock was developed by blending of waste cooking oil (WCO) with Jatropha curcas oil (JCO). The objective of this research is to evaluate significant factors contributing to the production of oil blends for bio lubricant application. The significant factors used in this study were oil ratio (WCO:JCO), agitation times (min) and agitation speed (rpm). The blended oil bio based lubricant was used to determine the saponification, acid, peroxide and iodine values. The experimental design used in this study was the 2 level-factorial design. In this experiment, it was found that the effect of oil ratio and interaction of oil ratio and agitation speed gave the most significant effect in oil blends as bio lubricant base stock. The highest ratio of oil blend 80 %:20 % WCO:JCO, with low agitation speed of 300 rpm and low agitation time of 30 minutes gave the optimum results. The acid, saponification, peroxide and iodine values obtained were 0.517±0.08 mg KOH/ g, 126.23±1.62 mg/ g, 7.5±2.0 m eq/ kg and 50.42±2.85 mg/ g respectively. A higher ratio of waste cooking oil blends was found to be favourable as bio lubricant base stock. (author)

Ultrasonic characterization of vegetable oil product

International Nuclear Information System (INIS)

Sidek Hj Abd Aziz; Chow Sai Pew; Abdul Halim Shaari; Nor Azizah Shaari

1992-01-01

The ultrasonic wave velocity and attenuation of a number vegetable oil products were measured using an ultrasonic pulse echo overlap technique from room temperature up to 90 0 C. Among the liquid samples studied were refined bleach deodorized (RED) palm oil, palm olein, coconut oil, corn oil and soya bean oil. The velocity of sound in vegetable oil products varies from about 1200 to 200 ms-1 and decrease linearly as the temperature increases. The ultrasonic properties of the oil are much dependent on their viscosity, density, relaxation effect and vibrational anharmonicity

[Efficiency evaluation of capsaicinoids to discriminate bio-waste oils from edible vegetable oils].

Science.gov (United States)

Mao, Lisha; Liu, Honghe; Kang, Li; Jiang, Jie; Liao, Shicheng; Liu, Guihua; Deng, Pingjian

2014-07-01

To evaluate the efficiency of capsaicinoids to discriminate bio-waste oil from edible vegetable oil. 14 raw vegetable oils, 24 fried waste oils, 34 kitchen-waste oils, 32 edible non-peanut vegetable oil, 32 edible peanuts oil, 16 edible oil add flavorand and 11 refined bio-waste oils were prepared and examined for capsaicinoids including capsaicin, dihydrocapsaicin and nonylic acid vanillylamide. The detection results of the above samples were statistically tested based on sample category to assessment identify the effectiveness of the bio-waste oils with capsaicinoids. As a indicator, capsaincin was possessed of high detection sensitivity and has the highest efficiency to discern kitchen-waste oils and refined bio-waste oils samples from edible non-peanut vegetable oil correctly. The accuracy rate of identification were 100% and 90.1% respectively. There is the background in peanut oil. CONCLUSION Capsaicin added in cooking process can be retained in the refining process and hardly be removed in the refining process. In the case of fully eliminating the background interference, capsaicinoids can effectively identify bio-waste oils and edible vegetable oil in combination.

Palm oil based biofuel using blended crude palm oil/medium fuel oil: physical and thermal properties studies. Paper no. IGEC-1-015

International Nuclear Information System (INIS)

Chuah, T.G.; Zakiah, M.; Wan Hasamuddin, W.H.; Hj. Ahmad, H.; Fakhru'l-Razi, A.; Robiah, Y.; Choong, T.S.Y.; Yip, Y.F.

2005-01-01

Crude Palm Oil (CPO) is renewable bio-based resource. It is an attractive alternative fuel which provides the potential to reduce emission problems. CPO is an example of biofuels that can be blended with petroleum distillates as a fuel in mobile engines and industrial processes to help offset the increasing energy demand. This paper highlights the results of blended Crude Palm Oil (CPO)/Medium Fuel Oil (MFO) as an alternative environmentally friendly boiler's fuel. Heating values of the blend fuels have been measured using an oxygen bomb calorimeter. Combustion performance of a blend containing 50% CPO in MFO fuel was examined using a commercial boiler. The blend burned satisfactorily without major modification to the appliance and fuel delivery system. SO 2 emissions were 51.67% lower than MFO, H 2 S decreased about 55.61% while NO x were 18.67% reduced. Results indicate potential reductions of SO 2 , H 2 S and NO x , and greenhouse gas emissions for the petroleum distillates can be replaced with this blend. (author)

Performance Testing of Diesel Engine using Cardanol-Kerosene oil blend

Directory of Open Access Journals (Sweden)

Ravindra

2018-01-01

Full Text Available Awareness of environmental pollution and fossil fuel depletion has necessitated the use of biofuels in engines which have a relatively cleaner emissions. Cardanol is a biofuel, abundantly available in India, which is a by-product of cashew processing industries. In this study performance of raw Cardanol blended with kerosene has been tested in diesel engine. Volumetric blend BK30 (30% kerosene and 70% Cardanol has been used for the test. The properties like flash point, viscosity and calorific value of the blend have been determined. The test was carried out in four stroke diesel engine connected with an eddy current dynamometer. Performance of the engine has been analysed by finding the brake specific fuel consumption (BSFC and brake thermal efficiency (BTE. The results showed that the brake thermal efficiency of the blend is 29.87%, with less CO and smoke emission compared to diesel. The results were also compared with the performance of Cardanol diesel blend and Cardanol camphor oil blend, which were already tested in diesel engines by other researchers. Earlier research work reveals that the blend of 30% camphor oil and 70% Cardanol performs very closer to diesel fuel with a thermal efficiency of 29.1%. Similarly, higher brake thermal efficiency was obtained for 20% Cardanol and 80% diesel blend.

Vegetable oil based liquid nanocomposite dielectric

Directory of Open Access Journals (Sweden)

Leon Chetty

2013-01-01

Full Text Available Physically smaller dielectric materials would improve the optimisation of space for power systems. Development of nanotechnology provides an effective way to improve the performances of insulating oils used in power system applications. In this research study, we focused on the development of nanomodified vegetable oils to be used in power transformers. Higher conduction currents were observed in virgin linseed oil than in virgin castor oil. However, for both virgin linseed and virgin castor oil, the DC conduction current increased approximately linearly with the applied DC voltage. In nanomodified linseed oil, the characteristic curve showed two distinct regions: a linear region (at lower applied voltage and a saturation region (at slightly higher voltage. Conversely, in nanomodified castor oil, the characteristic curve showed three distinct regions: a linear region (at lower applied voltage, a saturation region (at intermediate applied voltage and an exponential growth region (at higher applied voltage. The nanomodified linseed oil exhibited a better dielectric performance than the nanomodified castor oil. Overall, the addition of nanodielectrics to vegetable oils decreased the dielectric performance of the vegetable oils. The results of this study contribute to the understanding of the pre-breakdown phenomenon in liquid nanocomposite dielectrics.

Juice blends--a way of utilization of under-utilized fruits, vegetables, and spices: a review.

Science.gov (United States)

Bhardwaj, Raju Lal; Pandey, Shruti

2011-07-01

The post-harvest shelf life of maximum of fruits and vegetables is very limited due to their perishable nature. In India more then 20-25 percent of fruits and vegetables are spoiled before utilization. Despite being the world's second largest producer of fruits and vegetables, in India only 1.5 percent of the total fruits and vegetables produced are processed. Maximum amounts of fruit and vegetable juices turn bitter after extraction due to conversion of chemical compounds. In spite of being under utilized, the utilization of highly nutritive fruits and vegetables is very limited due to high acidity, astringency, bitterness, and some other factors. While improving flavor, palatability, and nutritive and medicinal value of various fruit juices such as aonla, mango, papaya, pineapple, citrus, ber, pear, apple, watermelon, and vegetables including bottle gourd, carrot, beet root, bitter gourd, medicinal plants like aloe vera and spices can also be used for juice blending. All these natural products are valued very highly for their refreshing juice, nutritional value, pleasant flavor, and medicinal properties. Fruits and vegetables are also a rich source of sugars, vitamins, and minerals. However, some fruits and vegetables have an off flavor and bitterness although they are an excellent source of vitamins, enzymes, and minerals. Therefore, blending of two or more fruit and vegetable juices with spices extract for the preparation of nutritive ready-to-serve (RTS), beverages is thought to be a convenient and economic alternative for utilization of these fruits and vegetables. Moreover, one could think of a new product development through blending in the form of a natural health drink, which may also serve as an appetizer. The present review focuses on the blending of fruits, under-utilized fruits, vegetables, medicinal plants, and spices in appropriate proportions for the preparation of natural fruit and vegetable based nutritive beverages.

Emissions of Jatropha oil-derived biodiesel blend fuels during combustion in a swirl burner

Science.gov (United States)

Norwazan, A. R.; Mohd. Jaafar, M. N.; Sapee, S.; Farouk, Hazir

2018-03-01

Experimental works on combustion of jatropha oil biodiesel blends of fuel with high swirling flow in swirl burner have been studied in various blends percentage. Jatropha oil biodiesel was produced using a two-step of esterification-transesterification process. The paper focuses on the emissions of biodiesel blends fuel using jatropha oil in lean through to rich air/fuel mixture combustion in swirl burner. The emissions performances were evaluated by using axial swirler amongst jatropha oil blends fuel including diesel fuel as baseline. The results show that the B25 has good emissions even though it has a higher emission of NOx than diesel fuel, while it emits as low as 42% of CO, 33% of SO2 and 50% of UHC emissions with high swirl number. These are due to the higher oxygen content in jatropha oil biodiesel.

Experimental investigation of engine emissions with marine gas oil-oxygenate blends

Energy Technology Data Exchange (ETDEWEB)

Nabi, Md. Nurun, E-mail: nurun.nabi@ntnu.no [Rajshahi University of Engineering and Technology (Bangladesh); Norwegian University of Science and Technology (NTNU) (Norway); Hustad, Johan Einar, E-mail: johan.e.hustad@ntnu.no [Norwegian University of Science and Technology (NTNU) (Norway)

2010-07-15

This paper investigates the diesel engine performance and exhaust emissions with marine gas oil-alternative fuel additive. Marine gas oil (MGO) was selected as base fuel for the engine experiments. An oxygenate, diethylene glycol dimethyl ether (DGM), and a biodiesel (BD) jatropha oil methyl ester (JOME) with a volume of 10% were blended with the MGO fuel. JOME was derived from inedible jatropha oil. Lower emissions with diesel-BD blends (soybean methyl ester, rapeseed methyl ester etc.) have been established so far, but the effect of MGO-BD (JOME) blends on engine performance and emissions has been a growing interest as JOME (BD) is derived from inedible oil and MGO is frequently used in maritime transports. No phase separation between MGO-DGM and MGO-JOME blends was found. The neat MGO, MGO-DGM and MGO-JOME blends are termed as MGO, Ox10 and B10 respectively. The experiments were conducted with a six-cylinder, four-stroke, turbocharged, direct-injection Scania DC 1102 (DI) diesel engine. The experimental results showed significant reductions in fine particle number and mass emissions, PM and smoke emissions with Ox10 and B10 fuels compared to the MGO fuel. Other emissions including total unburned hydrocarbon (THC), carbon monoxide (CO) and engine noise were also reduced with the Ox10 and B10 fuels, while maintaining similar brake specific fuel consumption (BSFC) and thermal efficiency with MGO fuel. Oxides of nitrogen (NOx) emissions, on the other hand, were slightly higher with the Ox10 and B10 fuels at high engine load conditions.

Phenolation of vegetable oils

Directory of Open Access Journals (Sweden)

ZORAN S. PETROVIĆ

2011-04-01

Full Text Available Novel bio-based compounds containing phenols suitable for the syn­thesis of polyurethanes were prepared. The direct alkylation of phenols with different vegetable oils in the presence of superacids (HBF4, triflic acid as ca­talysts was studied. The reaction kinetics was followed by monitoring the de­crease of the double bond content (iodine value with time. In order to under­stand the mechanism of the reaction, phenol was alkylated with model com­pounds. The model compounds containing one internal double bond were 9-oc­tadecene and methyl oleate and those with three double bonds were triolein and high oleic safflower oil (82 % oleic acid. It was shown that the best structures for phenol alkylation are fatty acids with only one double bond (oleic acid. Fatty acids with two double bonds (linoleic acid and three double bonds (lino­lenic acid lead to polymerized oils by a Diels–Alder reaction, and to a lesser extent to phenol alkylated products. The reaction product of direct alkylation of phenol with vegetable oils is a complex mixture of phenol alkylated with poly­merized oil (30–60 %, phenyl esters formed by transesterification of phenol with triglyceride ester bonds (<10 % and unreacted oil (30 %. The phenolated vegetable oils are new aromatic–aliphatic bio-based raw materials suitable for the preparation of polyols (by propoxylation, ethoxylation, Mannich reactions for the preparation of polyurethanes, as intermediates for phenolic resins or as bio-based antioxidants.

Environmentally Friendly Compatibilizers from Soybean Oil for Ternary Blends of Poly(lactic acid-PLA, Poly(ε-caprolactone-PCL and Poly(3-hydroxybutyrate-PHB

Directory of Open Access Journals (Sweden)

María Jesús Garcia-Campo

2017-11-01

Full Text Available Ternary blends of poly(lactic acid (PLA, poly(3-hydroxybutyrate (PHB and poly(ε-caprolactone (PCL with a constant weight percentage of 60%, 10% and 30% respectively were compatibilized with soybean oil derivatives epoxidized soybean oil (ESO, maleinized soybean oil (MSO and acrylated epoxidized soybean oil (AESO. The potential compatibilization effects of the soybean oil-derivatives was characterized in terms of mechanical, thermal and thermomechanical properties. The effects on morphology were studied by field emission scanning electron microscopy (FESEM. All three soybean oil-based compatibilizers led to a noticeable increase in toughness with a remarkable improvement in elongation at break. On the other hand, both the tensile modulus and strength decreased, but in a lower extent to a typical plasticization effect. Although phase separation occurred, all three soybean oil derivatives led somewhat to compatibilization through reaction between terminal hydroxyl groups in all three biopolyesters (PLA, PHB and PCL and the readily reactive groups in the soybean oil derivatives, that is, epoxy, maleic anhydride and acrylic/epoxy functionalities. In particular, the addition of 5 parts per hundred parts of the blend (phr of ESO gave the maximum elongation at break while the same amount of MSO and AESO gave the maximum toughness, measured through Charpy’s impact tests. In general, the herein-developed materials widen the potential of ternary PLA formulations by a cost effective blending method with PHB and PCL and compatibilization with vegetable oil-based additives.

Environmentally Friendly Compatibilizers from Soybean Oil for Ternary Blends of Poly(lactic acid)-PLA, Poly(ε-caprolactone)-PCL and Poly(3-hydroxybutyrate)-PHB.

Science.gov (United States)

Garcia-Campo, María Jesús; Quiles-Carrillo, Luis; Masia, Jaime; Reig-Pérez, Miguel Jorge; Montanes, Nestor; Balart, Rafael

2017-11-22

Ternary blends of poly(lactic acid) (PLA), poly(3-hydroxybutyrate) (PHB) and poly(ε-caprolactone) (PCL) with a constant weight percentage of 60%, 10% and 30% respectively were compatibilized with soybean oil derivatives epoxidized soybean oil (ESO), maleinized soybean oil (MSO) and acrylated epoxidized soybean oil (AESO). The potential compatibilization effects of the soybean oil-derivatives was characterized in terms of mechanical, thermal and thermomechanical properties. The effects on morphology were studied by field emission scanning electron microscopy (FESEM). All three soybean oil-based compatibilizers led to a noticeable increase in toughness with a remarkable improvement in elongation at break. On the other hand, both the tensile modulus and strength decreased, but in a lower extent to a typical plasticization effect. Although phase separation occurred, all three soybean oil derivatives led somewhat to compatibilization through reaction between terminal hydroxyl groups in all three biopolyesters (PLA, PHB and PCL) and the readily reactive groups in the soybean oil derivatives, that is, epoxy, maleic anhydride and acrylic/epoxy functionalities. In particular, the addition of 5 parts per hundred parts of the blend (phr) of ESO gave the maximum elongation at break while the same amount of MSO and AESO gave the maximum toughness, measured through Charpy's impact tests. In general, the herein-developed materials widen the potential of ternary PLA formulations by a cost effective blending method with PHB and PCL and compatibilization with vegetable oil-based additives.

Determination of the density and the viscosities of biodiesel-diesel fuel blends

Energy Technology Data Exchange (ETDEWEB)

Alptekin, Ertan; Canakci, Mustafa [Department of Mechanical Education, Kocaeli University, 41380 Kocaeli (Turkey); Alternative Fuels R and D Center, Kocaeli University, 41040 Kocaeli (Turkey)

2008-12-15

In this study, commercially available two different diesel fuels were blended with the biodiesels produced from six different vegetable oils (sunflower, canola, soybean, cottonseed, corn oils and waste palm oil). The blends (B2, B5, B10, B20, B50 and B75) were prepared on a volume basis. The key fuel properties such as density and viscosities of the blends were measured by following ASTM test methods. Generalized equations for predicting the density and viscosities for the blends were given and a mixing equation, originally proposed by Arrhenius and described by Grunberg and Nissan, was used to predict the viscosities of the blends. For all blends, it was found that there is an excellent agreement between the measured and estimated values of the density and viscosities. According to the results, the density and viscosities of the blends increased with the increase of biodiesel concentration in the fuel blend. (author)

New options for conversion of vegetable oils to alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A.; Kara, H. [Selcuk University, Konya (Turkey). Department of Chemical Engineering

2006-05-15

Biodiesel from transesterification of vegetable oils is an excellent alternative fuel. There is, however, a need to develop a direct process for conversion of vegetable oils into gasoline-competitive biodiesel and other petroleum products. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The purpose of the transesterification process is to lower the viscosity of vegetable oil. Compared to No. 2 diesel fuel, all of the vegetable oils are much more viscous, whereas methyl esters of vegetable oils are slightly more viscous. The methyl esters are more volatile than those of the vegetable oils. Conversion of vegetable oils to useful fuels involves the pyrolysis and catalytic cracking of the oils into lower molecular products. Pyrolysis produces more biogasoline than biodiesel fuel. Soap pyrolysis products of vegetable oils can be used as alternative diesel engine fuel. The soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon-rich products. Zinc chloride catalyst contributed greatly to high amounts of hydrocarbons in the liquid product. The yield of ZnCl2 catalytic conversion of the soybean oil reached the maximum 79.9% at 660 K. (author)

Experimental evaluation of diesel engine performance and emission using blends of jojoba oil and diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Huzayyin, A.S.; Rady, M.A.; Dawood, A. [Benha High Inst. of Technology (Egypt). Dept. of Mechanical Engineering Technology; Bawady, A.H. [University of Ain Shams, Cairo (Egypt). Faculty of Engineering

2004-08-01

An experimental evaluation of using jojoba oil as an alternate diesel engine fuel has been conducted in the present work. Measurements of jojoba oil chemical and physical properties have indicated a good potential of using jojoba oil as an alternative diesel engine fuel. Blending of jojoba oil with gas oil has been shown to be an effective method to reduce engine problems associated with the high viscosity of jojoba oil. Experimental measurements of different performance parameters of a single cylinder, naturally aspirated, direct injection, diesel engine have been performed using gas oil and blends of gas oil with jojoba oil. Measurements of engine performance parameters at different load conditions over the engine speed range have generally indicated a negligible loss of engine power, a slight increase in brake specific fuel consumption and a reduction in engine NO{sub x} and soot emission using blends of jojoba oil with gas oil as compared to gas oil. The reduction in engine soot emission has been observed to increase with the increase of jojoba oil percentage in the fuel blend. (Author)

Experimental evaluation of Diesel engine performance and emission using blends of jojoba oil and Diesel fuel

International Nuclear Information System (INIS)

Huzayyin, A.S.; Bawady, A.H.; Rady, M.A.; Dawood, A.

2004-01-01

An experimental evaluation of using jojoba oil as an alternate Diesel engine fuel has been conducted in the present work. Measurements of jojoba oil chemical and physical properties have indicated a good potential of using jojoba oil as an alternative Diesel engine fuel. Blending of jojoba oil with gas oil has been shown to be an effective method to reduce engine problems associated with the high viscosity of jojoba oil. Experimental measurements of different performance parameters of a single cylinder, naturally aspirated, direct injection, Diesel engine have been performed using gas oil and blends of gas oil with jojoba oil. Measurements of engine performance parameters at different load conditions over the engine speed range have generally indicated a negligible loss of engine power, a slight increase in brake specific fuel consumption and a reduction in engine NO x and soot emission using blends of jojoba oil with gas oil as compared to gas oil. The reduction in engine soot emission has been observed to increase with the increase of jojoba oil percentage in the fuel blend

Film-forming properties of castor oil polyol ester blends in elastohydrodynamic conditions

Science.gov (United States)

The viscosities and elastohydrodynamic (EHD) film thickness properties of binary blends of castor oil with polyol esters were determined experimentally. Predicted blend viscosity was calculated from the viscosity of the pure blend components. Measured viscosity values were closer to the values pre...

Heating Quality and Stability of Aqueous Enzymatic Extraction of Fatty Acid-Balanced Oil in Comparison with Other Blended Oils

Directory of Open Access Journals (Sweden)

Yang Li

2014-01-01

Full Text Available The heating performance of enzyme-assisted aqueous processing-extracted blended oil (EAEPO, hexane-extracted blended oil (HEBO, and three kinds of blended oils was investigated by varying the heating times. Oil degradation was monitored by analysis of the acid value (AV, peroxide value (PV, p-anisidine value (p-AV, color, and trans-fatty acid composition. The fatty acid ratios of EAEPO, HEBO, and the three kinds of blended oils were very similar (0.27 : 1.03 : 0.96, 0.27 : 1.08 : 1.16, 0.27 : 0.65 : 0.8, 0.27 : 0.6 : 0.84, and 0.27 : 0.61 : 0.79, resp.. The AV and color increased in proportion to the heating time for all the oils. There was a rapid increase in the PV and p-AV of EAEPO and HEBO after heating for only 1 h, whereas the other three blended oils showed a rapid increase after heating for 2 h or 6 h. Despite the highest trans-fatty acid content found for HEBO, this content was relatively low and remained low up to a heating time of 8 h. It was found that after heating, a fatty acid ratio relatively close to its ideal value (0.27 : 0.48 : 0.49 was maintained by EAEPO, which indicates that EAEPO is tolerant to heat treatment and is suitable for maintaining a healthy diet.

Diesel fuel from vegetable oil via transesterification and soap pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A.

2002-09-15

Transesterifications of 6 vegetable oil samples in supercritical methanol (SC MeOH) were studied without using any catalyst. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The variables affecting the methyl ester yielded during the transesterification reaction, such as the molar ratio of alcohol to vegetable oil and reaction temperature, were investigated. Compared to No. 2 diesel fuel, all of the vegetable oils are much more viscous, while methyl esters of vegetable oils are the slightly more viscous. The methyl esters are more volatile than those of the vegetable oils. The soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon-rich products. (author)

A blend of Sodium Humate/SLES/Herbal Oils

Directory of Open Access Journals (Sweden)

Yeliz Akyiğit

2013-08-01

Full Text Available A blend of sodium humate (SH with anionic surfactants such as sodium lauryl ether sulfate (SLES was prepared by solution mixing at medium of herbal oils at 25, 50 and 75°C. Its miscibility studies were carried out by using physical techniques over an extended range of concentration and composition in buffer solution. In addition, to ascertain the state of miscibility of the blends, they were investigated by using UV-visible spectrophotometer and Fourier transform infrared (FTIR. These values revealed that the blend is miscible when the sodium humate content is more than %60 in the blend at all temperatures. There were no important differences in the characteristics of the blends at different temperatures.It was thought that the mechanism ofthe complex formation is realized by making strong intermolecular interaction like hydrogen bonds between the carbonyl groups in humic acid and hydroxyl groups in fatty acids.

Changes on the Solid Fat Content of Palm Oil/ Sunflower Oil Blends via Inter esterification

International Nuclear Information System (INIS)

Suria Ramli; Azwani Mohd Lazim; Siti Aishah Hasbullah

2013-01-01

Physicochemical characteristics of binary blends containing refined-deodorized-bleached palm oil (RBDPO) and sunflower oil (SFO) were studied before and after chemical inter esterification at different temperature (110 degree Celsius (CIE1) and 80 degree Celsius (CIE2)) using sodium methoxide as catalyst. Thirty-three samples with different ratios were analyzed for triacylglycerol (TAG) composition, fatty acid composition (FAC) and solid fat content (SFC) profile. Upon CIE, extensive rearrangements of fatty acids among triacylglycerol (TAG) were seen. Generally, CIE not induced enormous changes in the TAG compositions of ratio 8:2 and 5:5 of RBDPO:SFO blends. However, CIE induced enormous changes in the TAG compositions of the 9:1, 7:3, 6:4, 4:6, 3:7, 2:8 and 1:9 blends, which some of the TAGs were increasing while the other decreasing. These changes in TAG profiles resulted in some changes in the physical properties (especially SFC) of the blends. Generally, the SFC of inter esterified blend were decreased after CIE1 and increased after CIE2, except for sample 10:0, 8:2, 7:3, 5:5 and 9:1 which were decreased after CIE1 and CIE2. As a conclusion, CIE1 and CIE2 successfully changed the physicochemical characteristics of the binary blends. (author)

EXPERIMENTAL COMBUSTION ANALYSIS OF A HSDI DIESEL ENGINE FUELLED WITH PALM OIL BIODIESEL-DIESEL FUEL BLENDS

Directory of Open Access Journals (Sweden)

JOHN AGUDELO

2009-01-01

Full Text Available Differences in the chemical nature between petroleum diesel fuels and vegetable oils-based fuels lead to differences in their physical properties affecting the combustion process inside the engine. In this work a detailed combustion diagnosis was applied to a turbocharged automotive diesel engine operating with neat palm oil biodiesel (POB, No. 2 diesel fuel and their blends at 20 and 50% POB by volume (B20 and B50 respectively. To isolate the fuel effect, tests were executed at constant power output without carrying out any modification of the engine or its fuel injection system. As the POB content in the blend increased, there was a slight reduction in the fuel/air equivalence ratio from 0.39 (B0 to 0.37 (B100, an advance of injection timing and of start of combustion. Additionally, brake thermal efficiency, combustion duration, maximum mean temperature, temperature at exhaust valve opening and exhaust gas efficiency decreased; while the peak pressure, exergy destruction rate and specific fuel consumption increased. With diesel fuel and the blends B20 and B50 the same combustion stages were noticed. However, as a consequence of the differences pointed out, the thermal history of the process was affected. The diffusion combustion stage became larger with POB content. For B100 no premixed stage was observed.

Combustion performance evaluation of air staging of palm oil blends.

Science.gov (United States)

Mohd Jaafar, Mohammad Nazri; Eldrainy, Yehia A; Mat Ali, Muhammad Faiser; Wan Omar, W Z; Mohd Hizam, Mohd Faizi Arif

2012-02-21

The problems of global warming and the unstable price of petroleum oils have led to a race to develop environmentally friendly biofuels, such as palm oil or ethanol derived from corn and sugar cane. Biofuels are a potential replacement for fossil fuel, since they are renewable and environmentally friendly. This paper evaluates the combustion performance and emission characteristics of Refined, Bleached, and Deodorized Palm Oil (RBDPO)/diesel blends B5, B10, B15, B20, and B25 by volume, using an industrial oil burner with and without secondary air. Wall temperature profiles along the combustion chamber axis were measured using a series of thermocouples fitted axially on the combustion chamber wall, and emissions released were measured using a gas analyzer. The results show that RBDPO blend B25 produced the maximum emission reduction of 56.9% of CO, 74.7% of NOx, 68.5% of SO(2), and 77.5% of UHC compared to petroleum diesel, while air staging (secondary air) in most cases reduces the emissions further. However, increasing concentrations of RBDPO in the blends also reduced the energy released from the combustion. The maximum wall temperature reduction was 62.7% for B25 at the exit of the combustion chamber.

Chemical Characteristics of Mango (Mangifera Indica L.) Kernel Oil and Palm Oil Blends for Probable use as Vanaspati

International Nuclear Information System (INIS)

Atta Muhammad Arif; Irman Javed; Muhammad Abdullah; Muhammad Irman; Athar Mahmud; Muhammad Nadeem; Muhammad Ayaz

2016-01-01

Chemical characteristics of blends of palm oil and mango kernel oil for their probable use as vanaspati was studied. Crude mango kernel oil was blended with refined, bleached and deodorised palm oil from 10 %, 20 %, 30 %, 40 % and 50 % (T 1 , T 2 , T 3 , T 4 and T 5 ) market vanaspati was used as control. Concentration of trans fatty acids in control was 22.7 %, whereas, all the vanaspati samples were virtually trans-free. Slip melting points (degree Celsius) of control, T 1 , T 2 , T 3 , T 4 and T 5 were 37.5, 37.3, 36.4, 35.6, 34.8 and 34. Free fatty acids of control and T5 were respectively 0.11, 0.12 %. Polymer contents of control, T 1 , T 2 , T 3 , T 4 and T 5 , after three heating cycles (18 degree Celsius, for 8 hr) were 21.55 %, 20.97 %, 18.66 %, 17.61 % and 10.22 %, respectively with lower solid fat index (p<0.05). Blends of mango kernel oil and palm oil can be used for the formulation of trans-free vanaspati. (author)

Effect of x-rays on edible vegetable oils

International Nuclear Information System (INIS)

Agba, E.H.; Chile, S.T.; Sombo, T.

2009-01-01

X-irradiated and non-irradiated vegetable oil sample were investigated by assessing the effect of the radiation on peroxide and fatty acid values on Turkey oil, Groundnut oil and Soya bean oil samples. The result of the investigation showed a rise in peroxide value by 99% for Turkey oil, 61% for Groundnut oil and 52% for Soya bean oil, while the acid value increased by as much as 58% for Turkey oil, 21% for Groundnut oil and 50% for Soya bean oil. These results show that X-irradiation has an adverse effect on the quality of edible vegetable oils

Exhaust emissions reduction from diesel engine using combined Annona-Eucalyptus oil blends and antioxidant additive

Science.gov (United States)

Senthil, R.; Silambarasan, R.; Pranesh, G.

2017-03-01

The limited resources, rising petroleum prices and depletion of fossil fuel have now become a matter of great concern. Hence, there is an urgent need for researchers to find some alternate fuels which are capable of substituting partly or wholly the higher demanded conventional diesel fuel. Lot of research work has been conducted on diesel engine using biodiesel and its blends with diesel as an alternate fuel. Very few works have been done with combination of biodiesel-Eucalypts oil without neat diesel and this leads to lots of scope in this area. The aim of the present study is to analyze the performance and emission characteristics of a single cylinder, direct injection, compression ignition engine using eucalyptus oil-biodiesel as fuel. The presence of eucalyptus oil in the blend reduces the viscosity and improves the volatility of the blends. The methyl ester of Annona oil is blended with eucalypts oil in 10, 20, 30, 40 and 50 %. The performance and emission characteristics are evaluated by operating the engine at different loads. The performance characteristics such as brake thermal efficiency, brake specific fuel consumption and exhaust gas temperature are evaluated. The emission constituents measured are Carbon monoxide (CO), unburned hydrocarbons (HC), Oxides of nitrogen (NOx) and Smoke. It is found that A50-Eu50 (50 Annona + 50 % Eucalyptus oil) blend showed better performance and reduction in exhaust emissions. But, it showed a very marginal increase in NOx emission when compared to that of diesel. Therefore, in order to reduce the NOx emission, antioxidant additive (A-tocopherol acetate) is mixed with Annona-Eucalyptus oil blends in various proportions by which NOx emission is reduced. Hence, A50-Eu50 blend can be used as an alternate fuel for diesel engine without any modifications.

Influence of a vegetable fat blend on the texture, microstructure and sensory properties of kashar cheese

Energy Technology Data Exchange (ETDEWEB)

Dinkci, N.; Kesenkas, H.; Seckin, A. K.; Kinik, O.; Gonc, S.

2011-07-01

The possibility of using a commercial vegetable fat blend in Kashar cheese was investigated. Kashar cheeses were manufactured by replacing the milk fat (MF) with a vegetable fat (VF) blend. Kashar cheeses from whole milk were also manufactured to compare textural, microstructural, meltability, color and sensory characteristics during a ripening period of 90 days. The use of vegetable fat decreased the meltability, hardness, cohesiveness, gumminess and chewiness of the cheese; while increasing adhesiveness where springiness was not affected. Differences became less notable toward the end of ripening. Scanning electron micrographs displayed VF cheese with a compact network with small and uniform fat globules embedded in the protein matrix. The MF cheese exhibited an open protein matrix containing milk fat globules of various sizes and forms. The color analysis demonstrated significant differences between cheeses. Finally, all sensory characteristics of the cheese were affected by the vegetable fat blend. (Author) 36 refs.

A Comparative Study on Formation of Polar Components, Fatty Acids and Sterols during Frying of Refined Olive Pomace Oil Pure and Its Blend Coconut Oil.

Science.gov (United States)

Ben Hammouda, Ibtissem; Triki, Mehdi; Matthäus, Bertrand; Bouaziz, Mohamed

2018-04-04

The frying performance of pure refined olive-pomace oil (ROPO) and blended with refined coconut oil (RCO) (80:20) was compared during a frying operation of French fries at 180 °C. Blending polyunsaturated oils with highly saturated or monounsaturated oils has been studied extensively, however in literature there is no study has been reported so far on blending ROPO (rich in monounsaturated fatty acids) with RCO (rich in saturated fatty acids) to formulate new frying oils. At the end of the frying process, the blend of ROPO/RCO exhibited a higher chemical stability than the pure ROPO based on total polar compounds (TPC), and polymers. The rate of TPC formation was achieved 23.3% and 30.6% for the blend and the pure oil, respectively. Trans and free fatty acids content, as well as anisidine value were also observed to be the highest in the pure ROPO. This study evaluated the frying performance in the search for appropriate frying oils to deliver healthy fried products with optimized nutritional qualities.

Anti-inflammatory properties of blended edible oil with synergistic antioxidants.

Science.gov (United States)

Upadya, Haridas; Devaraju, C J; Joshi, Shashank R

2015-01-01

Blending of oil combines the potency of two edible oils and offers a balance of fatty acids. Various cooking preparations existing across different ethnicities and regions subject oil to different cooking temperatures thereby causing deterioration of the oil due to oxidative stress. In order to prevent the oxidative damage of unsaturated fatty acid, a blend of rice bran oil (RBO) and safflower oil (SO) (70:30) with an antioxidant technology was designed. A controlled trial was carried out to assess the efficacy of the blend on different biomarkers including lipid parameters and some important inflammatory markers that have the potency to lead to various lifestyle diseases. A prospective, double-blind, randomized, parallel group study (on 80 adult hyperlipidemic patients) was conducted for 3 months. During the study, all the subjects were recommended lifestyle modifications, which included, exercise regime and diet counseling; oil quantity consumed was 1 L/person/month for both the groups. The subjects were divided into two groups; one group, continued with their regularly consumed oil whereas, the other was given the test oil. Biomarkers assessed were lipid profile and seven other inflammatory markers were assessed. Low-density lipoprotein cholesterol (LDL-C) the primary marker for cardiovascular diseases showed a decrease of 56.07 ± 04.31 mg/dL and 31.98 ± 03.81 mg/dL (P < 0.001 by analysis of variance [ANOVA]) from baseline in test and control group, respectively, during 3 months. Similar reduction trends were observed for total cholesterol where -52.31 ± 13.04 mg/dL and 31.98 ± 04.12 mg/dL (P < 0.001 by ANOVA, between the groups) were seen in test and control group, respectively. Oxidized LDL and high sensitivity C-reactive protein showed a reduction of 2.23 ± 1.3 units/dL and 0.87 ± 2.85 mg/L in test group whereas; an increase of 1.04 ± 1.73 units/dL and 0.44 ± 2.37 mg/L was seen in the control group, respectively (P < 0.05 by Student's t-test, between

Anti-inflammatory properties of blended edible oil with synergistic antioxidants

Directory of Open Access Journals (Sweden)

Haridas Upadya

2015-01-01

Full Text Available Background: Blending of oil combines the potency of two edible oils and offers a balance of fatty acids. Various cooking preparations existing across different ethnicities and regions subject oil to different cooking temperatures thereby causing deterioration of the oil due to oxidative stress. In order to prevent the oxidative damage of unsaturated fatty acid, a blend of rice bran oil (RBO and safflower oil (SO (70:30 with an antioxidant technology was designed. A controlled trial was carried out to assess the efficacy of the blend on different biomarkers including lipid parameters and some important inflammatory markers that have the potency to lead to various lifestyle diseases. Study Design: A prospective, double-blind, randomized, parallel group study (on 80 adult hyperlipidemic patients was conducted for 3 months. During the study, all the subjects were recommended lifestyle modifications, which included, exercise regime and diet counseling; oil quantity consumed was 1 L/person/month for both the groups. The subjects were divided into two groups; one group, continued with their regularly consumed oil whereas, the other was given the test oil. Biomarkers assessed were lipid profile and seven other inflammatory markers were assessed. Results: Low-density lipoprotein cholesterol (LDL-C the primary marker for cardiovascular diseases showed a decrease of 56.07 ± 04.31 mg/dL and 31.98 ± 03.81 mg/dL (P < 0.001 by analysis of variance [ANOVA] from baseline in test and control group, respectively, during 3 months. Similar reduction trends were observed for total cholesterol where −52.31 ± 13.04 mg/dL and 31.98 ± 04.12 mg/dL (P < 0.001 by ANOVA, between the groups were seen in test and control group, respectively. Oxidized LDL and high sensitivity C-reactive protein showed a reduction of 2.23 ± 1.3 units/dL and 0.87 ± 2.85 mg/L in test group whereas; an increase of 1.04 ± 1.73 units/dL and 0.44 ± 2.37 mg/L was seen in the control group

Experimental study of DI diesel engine performance using biodiesel blends with kerosene

Energy Technology Data Exchange (ETDEWEB)

Azad, A.K.; Ameer Uddin, S.M.; Alam, M.M. [Department of Mechanical Engineering, Bangladesh University of Engineering and Technology, Dhaka-1000 (Bangladesh)

2013-07-01

The experimental investigation offers a comprehensive study of DI diesel engine performance using bio-diesel from mustard oil blends with kerosene. The vegetable oil without trans-esterification reaction have been blended with kerosene oil by volume in some percentage like 20%, 30%, 40% and 50% which have been named as M20 (20% mustard, 80% kerosene), M30 (30% mustard, 70% kerosene), M40 (40% mustard, 60% kerosene) and M50 (50% mustard, 50% kerosene). The properties of the bio-fuel blended with kerosene have been tested in the laboratories with maintaining different ASTM standards. Then a four stroke, single cylinder, direct injection diesel engine has been mounted on the dynamometer bed for testing the performance of the engine using the bio-diesel blends. Several engine parameters like bsfc, bhp, break mean effective pressure, exhaust gas temperature, lube oil temperature, sound level etc. have been determined. A comparison has been made for engine performance of different bio-diesel blends with kerosene with the engine performance of diesel fuel.

A Complementary Biodiesel Blend from Soapnut Oil and Free Fatty Acids

Directory of Open Access Journals (Sweden)

Lu-Yen Chen

2012-08-01

Full Text Available Blends of biodiesels produced from soapnut oil and high-oleic free fatty acids (FFAs, which are potential non-edible oil feedstocks, were investigated with respect to their fuel properties. The soapnut oil methyl esters (SNME had satisfactory fuel properties with the exception of its high cold filter plugging point. In contrast, the biodiesel from the FFAs had favorable fuel properties such as a low cold filter plugging point of −6 °C; however, it exhibits poor oxidation stability with an induction period (IP of 0.2 h. The complementary blend of the SNME and the FFA-based biodiesel at various weight ratios was studied to improve the fuel properties. As a result, the biodiesel blend at a weight ratio of 70:30 can successfully meet all the biodiesel specifications, except the marginal oxidation stability. Furthermore, the effectiveness of N,N’-di-sec-butyl-p-phenylenediamine at the concentration between 100 and 500 ppm on the improvement in the oxidation stability of the biodiesel blend was examined. The relationship between the IP values associated with the consumption of antioxidants in the biodiesel blends was described by first-order reaction rate kinetics. In addition, the natural logarithm of IP (ln IP at various concentrations of antioxidant presented a linear relation with the test temperature. The IP at ambient temperature can be predicted based on the extrapolation of the temperature dependence relation.

Straight Vegetable Oil as a Diesel Fuel?

Energy Technology Data Exchange (ETDEWEB)

None

2014-01-01

Biodiesel, a renewable fuel produced from animal fats or vegetable oils, is popular among many vehicle owners and fleet managers seeking to reduce emissions and support U.S. energy security. Questions sometimes arise about the viability of fueling vehicles with straight vegetable oil (SVO), or waste oils from cooking and other processes, without intermediate processing. But SVO and waste oils differ from biodiesel (and conventional diesel) in some important ways and are generally not considered acceptable vehicle fuels for large-scale or long-term use.

Performance of Jatropha Oil Blends in RD270 Two Cylinders Four ...

African Journals Online (AJOL)

The performance characteristics of RD270 two cylinder, four stroke diesel engine fuelled with jatropha oil and its blend with diesel are presented in this paper. The jatropha biodiesel was obtained from National Research Institutes for Chemical Technology, Zaria, Nigeria. The produced biodiesel was blended with neat ...

Influence of non-edible vegetable based oil as cutting fluid on chip, surface roughness and cutting force during drilling operation of Mild Steel

Science.gov (United States)

Susmitha, M.; Sharan, P.; Jyothi, P. N.

2016-09-01

Friction between work piece-cutting tool-chip generates heat in the machining zone. The heat generated reduces the tool life, increases surface roughness and decreases the dimensional sensitiveness of work material. This can be overcome by using cutting fluids during machining. They are used to provide lubrication and cooling effects between cutting tool and work piece and cutting tool and chip during machining operation. As a result, important benefits would be achieved such longer tool life, easy chip flow and higher machining quality in the machining processes. Non-edible vegetable oils have received considerable research attention in the last decades owing to their remarkable improved tribological characteristics and due to increasing attention to environmental issues, have driven the lubricant industry toward eco friendly products from renewable sources. In the present work, different non-edible vegetable oils are used as cutting fluid during drilling of Mild steel work piece. Non-edible vegetable oils, used are Karanja oil (Honge), Neem oil and blend of these two oils. The effect of these cutting fluids on chip formation, surface roughness and cutting force are investigated and the results obtained are compared with results obtained with petroleum based cutting fluids and dry conditions.

Applicability of Vegetable Oils as a Wood Preservative

Directory of Open Access Journals (Sweden)

Eylem Dizman Tomak

2012-04-01

Full Text Available Conventional heavy duty wood preservatives have been banned or restricted for some applications due to their mammalian toxicity and their adverse effect on the environment. New, eco-friendly, but nevertheless still effective protection systems, is needed to protect wood in outdoors. Non-toxic vegetable oils can form of a protective layer on the surface of the wood cells which decrease water uptake of wood. For that reason, oils have a good potential as being a wood preservative. However, impregnation with vegetable oils is insufficient to impart adequate biological decay and termite resistance, and indeed the treatment may increase wood’s propensity to burn. In addition, a high level of oil absorption required for good protection make the process impractical and uneconomic to use. The efficiency of the treatment can be improved with using the biocides and oils together. Beside this, usage of modified oils can decrease the retention levels in wood. In this study, applicability of vegetable oils being one of the environment-friendly, biodegradable water repellents on wood treatments was reported. Furthermore, problems related to the use of oils for wood protection, and possible solutions for the problems were discussed.In this study, applicability of vegetable oils as one of the environment-friendly, biodegradable water repellents was reported. Furthermore, problems related to the use of oils for wood protection and possible solutions for the problems were discussed

[Rapid discriminating hogwash oil and edible vegetable oil using near infrared optical fiber spectrometer technique].

Science.gov (United States)

Zhang, Bing-Fang; Yuan, Li-Bo; Kong, Qing-Ming; Shen, Wei-Zheng; Zhang, Bing-Xiu; Liu, Cheng-Hai

2014-10-01

In the present study, a new method using near infrared spectroscopy combined with optical fiber sensing technology was applied to the analysis of hogwash oil in blended oil. The 50 samples were a blend of frying oil and "nine three" soybean oil according to a certain volume ratio. The near infrared transmission spectroscopies were collected and the quantitative analysis model of frying oil was established by partial least squares (PLS) and BP artificial neural network The coefficients of determina- tion of calibration sets were 0.908 and 0.934 respectively. The coefficients of determination of validation sets were 0.961 and 0.952, the root mean square error of calibrations (RMSEC) was 0.184 and 0.136, and the root mean square error of predictions (RMSEP) was all 0.111 6. They conform to the model application requirement. At the same time, frying oil and qualified edible oil were identified with the principal component analysis (PCA), and the accurate rate was 100%. The experiment proved that near infrared spectral technology not only can quickly and accurately identify hogwash oil, but also can quantitatively detect hog- wash oil. This method has a wide application prospect in the detection of oil.

Straight vegetable oil use in Micro-Gas Turbines: System adaptation and testing

International Nuclear Information System (INIS)

Prussi, M.; Chiaramonti, D.; Riccio, G.; Martelli, F.; Pari, L.

2012-01-01

Highlights: → The possibility to feed a Micro Gas Turbine with Straight Vegetable Oil (SVO) has been investigated. → Correlative analysis and CFD were used to model the effect of SVO characteristics on atomization and evaporation. → Minor modifications to a the commercial MGT were adopted. → Measured power output and specific fuel consumption were close to standard fuel, taking into account the LHV of SVO. → Emissions were higher than for standard fossil fuel but strongly affected by SVO temperature. -- Abstract: The aim of this research work is to investigate the use of straight vegetable sunflower oil (SFO), a liquid biofuel, in a Micro-Gas Turbine (MGT). Compared to conventional diesel engines, micro-gas turbines represent a very reliable, clean and performing small scale cogeneration technology. Commercial gas turbines have already been tested with unconventional fuels, such as biomass derived fuels; however, research work on using Straight Vegetable Oil (SVO) as fuel in MGTs are really scarce. The chemical and physical characteristics of SVO are different from fossil diesel oil and rather far from the common technical specifications for gas turbine liquid fuels, not only in terms of kinematic viscosity and Lower Heating Value, but also as regards other issues as contaminant levels and composition, fuel cold properties, ignition properties, etc. Therefore, particular attention has to be given to the atomization and evaporation phases, as these are the most critical steps to achieve stable and efficient long term operation. An analysis based on numerical correlations available from literature was initially adopted for the analysis of the atomization process, supported by CFD modeling to qualitatively investigate the flow pattern. Control parameters were revised and set so to produce a sunflower oil spray having evaporation time comparable to diesel, and minor adaptations to the fuel line were designed and installed on the MGT. Tests with blends and

An Investigation of Viscosities, Calorific Values and Densities of Binary Biofuel Blends

Directory of Open Access Journals (Sweden)

Che Mat Sharzali

2017-01-01

Full Text Available Straight vegetable oil (SVO biofuel is a promising alternative to petroleum diesel fuel primarily due to its comparable physical properties to that of petroleum diesel fuel. However, the relatively higher viscosity of SVO limits its direct application in diesel engine. To resolve this issue, binary biofuel blends was introduced in this study to reduce the viscosity of SVO. In this work, a novel biofuel namely Melaleuca Cajuputi oil (MCO was used and blended with refined palm oil (RPO. A total of four blends with the mixing ratios of 20%, 40%, 50% and 60% of MCO were prepared. Various key properties of dynamic viscosity, calorific value and density of the blends were measured and benchmarked against the biodiesel standards based on ASTM D6751. It was found that viscosity and density of the blends decreased with the increase of MCO fraction. Meanwhile, the calorific value of the blends increased linearly as the MCO fraction increased. The blend of 40RPO60MCO was found to have comparable key properties of viscosity, calorific value and density to those of petroleum diesel fuel and ASTM D6751 standard.

Swelling and tribological properties of melt-mixed fluoroelastomer/nitrile rubber blends under crude oil

Science.gov (United States)

Tagelsir, Yasin; Li, San-Xi; Lv, Xiaoren; Wang, Shijie; Wang, Song; Osman, Zeinab

2018-01-01

The melt-mixed fluoroelastomer (FKM)/ nitrile rubber (NBR) blends of (90/10, 80/20, 70/30, 60/40 and 50/50) ratios with same hardness were prepared, and their swelling and tribological properties under crude oil were investigated for the purpose of developing high performance cost-effective elastomers meeting requirement of oil extraction progressive cavity pump stator. Differential scanning calorimetry confirmed compatible blend system for all blends. Field emission scanning electron microscopy (FE-SEM) showed co-continuous morphology of 200-400 nm phase size for all blends, expect FKM/NBR (90/10) which exhibited partially continuous phase morphology of 100-250 nm phase size. The results of swelling and linear wear tests under crude oil indicated that swelling percentage, coefficient of friction and specific wear rate of FKM/NBR blends were much better than NBR, with FKM/NBR (90/10 and 80/20) showing swelling percentage and specific wear rate very close to FKM. Attenuated total reflectance-Fourier transform infrared spectroscopy disclosed that fracture of macromolecular chains was the main mechanochemical effect of unswollen and swollen worn surfaces, in addition to oxygenated degradation detected with increasing NBR ratio in the blends. The fracture of macromolecular chains resulted in slight fatigue wear mechanism, which was also confirmed by FE-SEM of the worn surfaces.

Performance characteristics of mix oil biodiesel blends with smoke emissions

Directory of Open Access Journals (Sweden)

Sanjay Mohite

2016-08-01

Full Text Available Fossil fuel resources are being depleted day by day and its use affects the environment adversely. Renewable energy is one of the alternate for sustainable development and biodiesel is one of the suitable alternate which can replace the diesel. The major hurdles in the successful commercialization of biodiesel are high feedstock cost and conversion technology to reduce viscosity. The choice of raw material and biodiesel production method must depend upon techno-economical view. There are some specific regions for different types of oil availability. It is therefore required to produce biodiesel from the mixture of oils to fulfill the requirements of energy demand in a particular country according to its suitability and availability of feedstock. Karanja and Linseed crops  are abundantly available in India. Biodiesel was produced from a mixture of Karanja and Linseed oils by alkaline transesterification. In this experimental study, biodiesel blends of 10%, 20% and 30% were used with diesel in a diesel engine at a constant speed of 1500 rpm with varying brake powers (loads from 0.5 kW to 3.5kW to evaluate brake thermal efficiency, brake specific fuel consumption,  brake specific energy consumption, exhaust gas temperature, mechanical efficiency, volumetric efficiency, air fuel ratio and smoke opacity. They were compared with diesel and found satisfactory. BTE was found to be  28.76% for B10 at 3.5kW load.  Smoke opacity was also found to be reduced with all blends. Smoke opacity was found to be reduced up to 10.23% for B10 biodiesel blend as compared to that of diesel at 3.5kW. Experimental investigation  has revealed that  biodiesel produced from a mixture of Karanja and Linseed oils can be successfully used in diesel engines without any engine modification  and B10 was found to be an optimum biodiesel blend in terms of brake thermal efficiency. Article History: Received April 14th 2016; Received in revised form June 25th 2016; Accepted

Determination of the physical characteristics of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Andrade, Danielle Oliveira de; Andrade, Ednilton Tavares de; Pereira, Roberto Guimaraes [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Agricola e do Meio Ambiente; Tulcan, Oscar Edwin Piamba [Universidade Nacional da Colombia (UNAL), Bogota (Colombia). Fac de Ingenieria

2008-07-01

The objective of this work was the characterization of vegetable oils of canola, sunflower, corn and soybean through corrosion, kinematic viscosity, density, cloud point and flow point tests. Vegetable oils are used as raw material for preparation of biofuels or as fuel diesel additive or substitute. The vegetable oils tested showed a low level of corrosion, kinematic viscosities are measured in the range of 31 to 36 mm{sup 2}.s{sup -1}, density was tested at 15 and 20 deg C and showed results varying in the third decimal order. For the oils tested, the cloud point is around 0 deg C and the flow point around -17 deg C. (author)

Basic properties of crude rubber seed oil and crude palm oil blend as a potential feedstock for biodiesel production with enhanced cold flow characteristics

Energy Technology Data Exchange (ETDEWEB)

Yusup, Suzana; Khan, Modhar [Chemical Engineering Department, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia)

2010-10-15

Research and development in the field of biodiesel showed that fatty acid methyl esters synthesized from agriculture or animal oils and fats, which exhibit qualifying properties, can replace diesel fuel used in internal combustion engine. However, the industry had some downfall recently with the fluctuating prices of edible oils and increasing demand for nutritional needs. Crude rubber seed oil (CRSO) and crude palm oil (CPO) were used in this study since both can be extracted and produced locally in Malaysia from their abundant plantations. The benefits of introducing such blend are that CRSO is considered a non-edible feedstock with no major industrial utilizations that has the potential to reduce the usage of CPO in biodiesel industry and was found to enhance the cold flow characteristics when blended with CPO by reducing the saturated fatty acids in the feedstock. The oils and blends were characterized for density, kinematic viscosity, heating value, acid value, free fatty acid content, refractive index, mono-, di- and triglycerides and sulphur content. Fatty acids composition and iodine value were established for an equivolume blend of the oils. (author)

Basic properties of crude rubber seed oil and crude palm oil blend as a potential feedstock for biodiesel production with enhanced cold flow characteristics

International Nuclear Information System (INIS)

Yusup, Suzana; Khan, Modhar

2010-01-01

Research and development in the field of biodiesel showed that fatty acid methyl esters synthesized from agriculture or animal oils and fats, which exhibit qualifying properties, can replace diesel fuel used in internal combustion engine. However, the industry had some downfall recently with the fluctuating prices of edible oils and increasing demand for nutritional needs. Crude rubber seed oil (CRSO) and crude palm oil (CPO) were used in this study since both can be extracted and produced locally in Malaysia from their abundant plantations. The benefits of introducing such blend are that CRSO is considered a non-edible feedstock with no major industrial utilizations that has the potential to reduce the usage of CPO in biodiesel industry and was found to enhance the cold flow characteristics when blended with CPO by reducing the saturated fatty acids in the feedstock. The oils and blends were characterized for density, kinematic viscosity, heating value, acid value, free fatty acid content, refractive index, mono-, di- and triglycerides and sulphur content. Fatty acids composition and iodine value were established for an equivolume blend of the oils.

KARAKTERISTIK MINYAK CAMPURAN RED PALM OIL DENGAN PALM KERNEL OLEIN (Characteristics of Oil Blends from Red Palm Oil and Palm Kernel Olein

Directory of Open Access Journals (Sweden)

Maria Ulfah

2016-10-01

Full Text Available Characteristics of oil blends has been produced from red palm oil (RPO and palm kernel olein (PKOo with seven ratios with a total of 100, namely A (0:100, B (25:75, C (40:60, D (50:50, E (60:40, F (75:25 and G (100:0 v/v investigated with randomized complete block design. The result showed that different of ratio levels RPO and PKOo have some effects on peroxide value, saponification value, melting point, cloud point and β-carotene content from RPO-PKOo oil blends, but has not effect on free fatty acid content. Higher level of PKOo content on formulas oil blends were decreased of saponification value and melting point, but was increased of cloud point. The best of RPOPKOo oil blends has been obtained at ratio 50:50 (v/v, with 459.52 ppm β-carotene, 1.35 meq/kg peroxide value, 0.09 % free fatty acid, 202.60 saponification value, 24.15 oC melting point and 7.15 oC cloud point. Fatty acids composition were 1.24 % capric acid, 29.00 % lauric acid, 10.09 % miristic acid, 23.10 % palmitic acid, 5.84 linoleic acid, 27.30 % oleic acid and 3.43 % stearic acid. Keywords: Red palm oil, palm kernel olein, oil blends, chemical and physical properties ABSTRAK Sifat-sifat minyak campuran yang dihasilkan dari red palm oil (RPO dan palm kernel olein (PKOo dengan tujuh tingkat rasio yang totalnya 100, yaitu A (0:100, B (25:75, C (40:60, D (50:50, E (60:40, F (75:25 dan G (100:0 (v/v dikaji menggunakan rancangan acak lengkap kelompok. Hasil penelitian menunjukkan bahwa rasio RPO:PKOo mempengaruhi angka peroksida, angka penyabunan, melting point, cloud point dan kadar β-karoten dari minyak campuran RPO-PKOo yang dihasilkan, namun tidak mempengaruhi kadar asam lemak bebas. Peningkatan jumlah PKOo yang ditambahkan dalam minyak campuran RPO-PKOo, akan menurunkan angka penyabunan dan melting point, namun akan menaikkan cloud point. Produk minyak campuran RPO-PKOo terbaik diperoleh pada rasio 50:50 (v/v, dengan kadar β-karoten 459,52 ppm, angka peroksida 1,35 meq

Evaluation of emissions in gas powered electric generator engine with vegetable oil; Avaliacao das emissoes de gases em motor gerador eletrico alimentado com oleo vegetal

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Thalita C. de; Cunha, Joao Paulo Barreto; Cotrim, Suzane Santana; Brito, Gustavo Mendes; Delmond, Josue Gomes [Universidade Estadual de Goias (UNUCET/UEG), Anapolis, GO (Brazil). Unidade Universitaria de Ciencias Exatas e Tecnologicas], E-mail: thalitacarrijo@gmail.com

2012-11-01

The use of vegetable oils as fuel in diesel engines is a good alternative to reduce emissions of greenhouse gases in the atmosphere from the use of fossil fuels, either in pure form or as biodiesel. The soybean, oilseed single high-availability in Brazil, is the most viable feedstock for the production of oil and its use as a fuel because of the structure of production, distribution and grain crushing. This study aimed to evaluate the performance of a duty diesel generator fueled with blends of diesel and soybean oil at concentrations of 10%, 25%, 50% and 75%, and soybean oil pure, 100%. During the tests we evaluated the energy consumption of the generator and the emission of greenhouse gases (O{sub 2}, CO, CO{sub 2}, NO{sub x} and SO{sub 2}), according to the demand of electric charges (0, 500, 1000, 1500 and 2000 Watts) connected to the group generator. The results, using the F test, showed that the hourly consumption of fuel increased with increasing concentration in the mixture of diesel fuel and engine load demand from the generator. It follows that in the environment, increasing the oil concentration in the mixture caused a reduction in emissions, except for the emission of oxygen. The best choice for the operation for the engine generator using vegetable oil soya be provided for up to 60 % oil in the mixture and load demand up to 1000W, in which occurred lower emissions of carbon monoxide (CO) and therefore improved efficiency in the combustion process. (author)

Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil

Directory of Open Access Journals (Sweden)

Gamel, T. H.

1999-10-01

Full Text Available Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil. Methanol phenolic extracts of dry rosemary leaves and olive vegetable water filtrate, in combination with BHA, were added to olive oil (blend of refined and virgin olive oil, 3 to 1 and to sunflower oil and their antioxidant effects under accelerated conditions were evaluated. Accelerated conditions included the oven test (at 63 °C and the conductivity method (Rancimat at 120 °C. Frying process at 180 °C was also applied. The methanol phenolic extracts and the BHA were added to each oil at the following concentrations: 200 ppm rosemary extract; 200 ppm olive vegetable water extract; 100 ppm rosemary extract + 100 ppm BHA; 100 ppm vegetable water extract + 100 ppm BHA and 200 ppm BHA. In general, antioxidant effect of phenolic additives of rosemary and of BHA was in the following order: 200 ppm rosemary extract > 100 ppm rosemary extract + 100 ppm BHA > and 200 ppm BHA. The addition of 200 ppm vegetable water extract and 100 ppm vegetable water extract + 100 ppm BHA exhibited similar antioxidant effect to that of 200 ppm BHA.

Extractos metanólicos de fenoles de hojas secas de romero y filtrados de agua de vegetación de la aceituna, en combinación con BHA, se añadieron al aceite de oliva (mezcla de aceite de oliva refinado y virgen, 3 a 1 y al aceite de girasol, evaluándose sus efectos antioxidantes usando condiciones aceleradas. Estas condiciones incluyeron el test del horno de oxidación (a 63 °C y el método de conductividad (Rancimat a 120 °C. También se aplicó al proceso de fritura a 180 °C. Los extractos metanólicos de fenoles y el BHA se añadieron a cada aceite en las siguientes concentraciones: 200 ppm de extracto de romero, 200 ppm de extracto de agua de vegetación de la aceituna, 100 ppm de extracto de romero + 100 ppm de BHA, 100 ppm de extracto de agua de vegetación + 100 ppm de BHA y 200 ppm de BHA

LDPE/PHB blends filled with castor oil cake

Science.gov (United States)

Burlein, Gustavo A.; Rocha, Marisa C. G.

2015-05-01

The response surface methodology (RSM) is a collection of mathematical techniques useful for developing, improving and optimizing process. In this study, RSM technique was applied to evaluate the effect of the components proportion on the mechanical properties of low density polyethylene (LDPE)/ poly (3-hydroxy-butyrate) (PHB) blends filled with castor oil cake (CC). The blends were prepared by melt mixing in a twin screw extruder. Low density polyethylene, poly (3-hydroxy-butyrate) and castor oil pressed cake were represented by the input variables designated as LDPE, PHB and CC, respectively. As it was desirable to consider the largest LDPE content in the ternary system, the components of the mixture were subjected to the following constraints: 0.7 ≤ LDPE ≤ 1.0, 0≤ PHB≤0.3 e 0 ≤ CC ≤0.3. The mechanical properties of the different mixtures were determined by conventional ASTM tests and were evaluated through analysis of variance performed by the Minitab software. Some polynomial equations were tested in order to describe the mechanical behavior of the samples. The quadratic model in pseudo components was selected for describing the tensile behavior because it was the most efficient from a statistical point of view (p-value ≤ 0.05; coefficient of determination (r2) close to 1 and variation inflation factor (VIF) values PHB or CC. The tensile strength values of binary mixtures of LDPE lie in the range from 8.9 to 10 MPa. As some commercial grades of LDPE have mechanical strength in this range, it may be inferred that the addition of a certain amount of PHB or CC to LDPE may be considered as a possibility for obtaining LDPE based materials with increased susceptibility to biodegradation. The cubic model in pseudo components was selected for describe the flexural strength of the samples because it was the most adequate from a statistical point of view. However, the linear model in pseudo components was the most efficient to describe the flexural modulus

Epoxidized Vegetable Oils Plasticized Poly(lactic acid Biocomposites: Mechanical, Thermal and Morphology Properties

Directory of Open Access Journals (Sweden)

Buong Woei Chieng

2014-10-01

Full Text Available Plasticized poly(lactic acid PLA with epoxidized vegetable oils (EVO were prepared using a melt blending method to improve the ductility of PLA. The plasticization of the PLA with EVO lowers the Tg as well as cold-crystallization temperature. The tensile properties demonstrated that the addition of EVO to PLA led to an increase of elongation at break, but a decrease of tensile modulus. Plasticized PLA showed improvement in the elongation at break by 2058% and 4060% with the addition of 5 wt % epoxidized palm oil (EPO and mixture of epoxidized palm oil and soybean oil (EPSO, respectively. An increase in the tensile strength was also observed in the plasticized PLA with 1 wt % EPO and EPSO. The use of EVO increases the mobility of the polymeric chains, thereby improving the flexibility and plastic deformation of PLA. The SEM micrograph of the plasticized PLA showed good compatible morphologies without voids resulting from good interfacial adhesion between PLA and EVO. Based on the results of this study, EVO may be used as an environmentally friendly plasticizer that can improve the overall properties of PLA.

Oil product blending optimization system; Sistema de otimizacao de misturas de derivados

Energy Technology Data Exchange (ETDEWEB)

Costa, F.L.P.; Sousa, L.C.F.; Joly, M.; Takahashi, M.T.; Magalhaes, M.V.O.; Mendonca, P.N. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2008-07-01

The current scenario of the world refining industry demands significant investment in the improvement of its products and production processes quality, either due to a competitive market or strict environmental restrictions, requiring deep changes in the oil companies. In this environment, blending optimization has been receiving increasing attention in both academic and industrial sectors resulting in the development and improvement of tools for decision support and realtime control. The main objective of these tools is to optimize, according to either an economic or an operational criterion, the fuel blending recipe, guaranteeing the product specification with minimum giveaway in the critical properties and avoiding the reblending process. This work presents a blending optimization system of oil products named OTIMIST and instances of its application in PETROBRAS' Recap refinery. (author)

The properties of poly(lactic acid)/starch blends with a functionalized plant oil: tung oil anhydride.

Science.gov (United States)

Xiong, Zhu; Li, Chao; Ma, Songqi; Feng, Jianxian; Yang, Yong; Zhang, Ruoyu; Zhu, Jin

2013-06-05

Bio-sourced polymers, polylactide (PLA) and starch, have been melt-blended by lab-scale co-extruder with tung oil anhydride (TOA) as the plasticizer. The ready reaction between the maleic anhydride on TOA and the hydroxyl on starch led TOA molecules to accumulate on starch and increased the compatibility of PLA/starch blends, which was confirmed by FT-IR analyses and SEM. The TOA could change the mechanical properties and physical behaviors of PLA/starch blends. DSC and DMA analysis show that the TOA layer on starch has an effect on the thermal behavior of PLA in the ternary blend. The enrichment of TOA on starch improves the toughness and impact strength of the PLA/starch blends. The adding amount of TOA in PLA/starch blends primarily determined the compatibility and mechanical properties of the resulted ternary blends. The tensile and impact fracture modes of the PLA/starch blend with or without TOA has also been investigated by SEM analysis. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Mathematical Modeling of Vegetable-Oil Crystallization

DEFF Research Database (Denmark)

Hjorth, Jeppe Lindegaard

be desirable to enhance specific properties such as shelf life, viscosity, texture, sensory aspects and physical appearance. Vegetable oils and fats constitute a considerable part of many food products such as chocolate, margarine, bread, spreads and ice cream. Several attractive properties found......In recent years the food sector has experienced a great boost in demand for tailor-made fats and oils to produce so-called functional foods, where ingredients have been carefully modified to yield products with specific, valuable properties. Depending on market segment and product, it may...... in these products, including flavor release, melting profile and appearance, are governed by the oils and fats added. Consequently, altering the fat phase may lead to enhanced properties of the products. The primary focus of the present work is vegetable oils and fats originating from different sources covering...

The potential of using vegetable oil fuels as fuel for diesel engines

International Nuclear Information System (INIS)

Altin, Recep; Cetinkaya, Selim; Yucesu, Huseyin Serdar

2001-01-01

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. The effects of vegetable oil fuels and their methyl esters (raw sunflower oil, raw cottonseed oil, raw soybean oil and their methyl esters, refined corn oil, distilled opium poppy oil and refined rapeseed oil) on a direct injected, four stroke, single cylinder diesel engine performance and exhaust emissions was investigated in this paper. The results show that from the performance viewpoint, both vegetable oils and their esters are promising alternatives as fuel for diesel engines. Because of their high viscosity, drying with time and thickening in cold conditions, vegetable oil fuels still have problems, such as flow, atomisation and heavy particulate emissions. (Author)

The potential of using vegetable oil fuels as fuel for diesel engines

Energy Technology Data Exchange (ETDEWEB)

Altin, Recep [Ministry of Education, Projects Coordination Unit, Ankara (Turkey); Cetinkaya, Selim [Gazi Univ., Technical Education Faculty, Ankara (Turkey); Yucesu, Huseyin Serdar [Karaelmas Univ., Technical Education Faculty, Karabuk (Turkey)

2001-03-01

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. The effects of vegetable oil fuels and their methyl esters (raw sunflower oil, raw cottonseed oil, raw soybean oil and their methyl esters, refined corn oil, distilled opium poppy oil and refined rapeseed oil) on a direct injected, four stroke, single cylinder diesel engine performance and exhaust emissions was investigated in this paper. The results show that from the performance viewpoint, both vegetable oils and their esters are promising alternatives as fuel for diesel engines. Because of their high viscosity, drying with time and thickening in cold conditions, vegetable oil fuels still have problems, such as flow, atomisation and heavy particulate emissions. (Author)

Effects of composition and processing conditions on morphology and properties of thermoplastic elastomer blends of SEBS-PP-Oil and dynamically vulcanized EPDM-PP-Oil

NARCIS (Netherlands)

Sengupta, P.; Noordermeer, Jacobus W.M.

2004-01-01

This work presents a comparative study of the morphology and structure-related properties of thermoplastic elastomer blends based on SEBS-PP-oil and dynamically vulcanized EPDM-PP-oil prepared under identical conditions. Compositions of each blend type with three different SEBS-PP and EPDM-PP ratios

Liquid Soap Production with Blends Of Rubber Seed Oil (RSO) And ...

African Journals Online (AJOL)

The production of liquid detergent using locally sourced palm fruit bunch (Elaeis Guineesis) waste saponier has been investigated. An optimum blend ratio of rubber seed oil to palm kernel oil RSO:PKO 20:80 being constituent elements used for the production of the soap; was obtained using the Duncan Multiple Range ...

Non-conventional use of vegetable oils: Possibilities and prospects

International Nuclear Information System (INIS)

Pellizzi, G.

1992-01-01

This paper examines the feasibility, relative to the specific capabilities of the Italian agricultural industry, of the production of biomass fuels and lubricating oils. A comparative cost benefit analysis is made to determine the technical and economic convenience of the production of grain or vegetable oil derived biomass for direct use as lubricants, fuel oils or for conversion into ethanol fuels. The suitability of different types of engines is examined for the direct combustion of vegetable oils and for the combustion of ethanol fuels. The study also has a look at what should be the suitable mix of Italian Government agricultural, environmental and fiscal strategies to support and encourage the production and use of industrial vegetable fuel oils and lubricants

Comparative studies of the rheological behaviour of oil epoxy and oil polyesteramide blends with polymethacrylic acid

Directory of Open Access Journals (Sweden)

Ufana Riaz

2017-05-01

Full Text Available Polymer blends have replaced a variety of pristine polymers in different sectors due to their desired synergetic properties such as durability, heat resistance, reduced wear & tear, flexibility, chemical resistance and longer shelf life that can be achieved by making minor alterations in their compositions. The modification of polymer blends by using sustainable resource based polymers can not only fulfil our ecological but also our economic and social needs. The present work reports the compatibility studies of oil derived epoxy and polyesteramide blends with polymethacrylic acid (PMA. The aim is to highlight the role of rheology in predicting the compatibility of these blends in the solution and solid phases which is a crucial parameter that decides the processibility and viability of these materials for commercialization.

Experimental investigations on a diesel engine operated with fuel blends derived from a mixture of Pakistani waste tyre oil and waste soybean oil biodiesel.

Science.gov (United States)

Qasim, Muhammad; Ansari, Tariq Mahmood; Hussain, Mazhar

2017-10-18

The waste tyre and waste cooking oils have a great potential to be used as alternative fuels for diesel engines. The aim of this study was to convert light fractions of pyrolysis oil derived from Pakistani waste vehicle tyres and waste soybean oil methyl esters into valuable fuel and to reduce waste disposal-associated environmental problems. In this study, the waste tyre pyrolysis liquid (light fraction) was collected from commercial tyre pyrolysis plant and biodiesel was prepared from waste soybean oil. The fuel blends (FMWO10, FMWO20, FMWO30, FMWO40 and FMWO50) were prepared from a 30:70 mixture of waste tyre pyrolysis liquid and waste soybean oil methyl esters with different proportions of mineral diesel. The mixture was named as the fuel mixture of waste oils (FMWO). FT-IR analysis of the fuel mixture was carried out using ALPHA FT-IR spectrometer. Experimental investigations on a diesel engine were carried out with various FMWO blends. It was observed that the engine fuel consumption was marginally increased and brake thermal efficiency was marginally decreased with FMWO fuel blends. FMWO10 has shown lowest NOx emissions among all the fuel blends tested. In addition, HC, CO and smoke emissions were noticeably decreased by 3.1-15.6%, 16.5-33.2%, and 1.8-4.5%, respectively, in comparison to diesel fuel, thereby qualifying the blends to be used as alternative fuel for diesel engines.

Review of Heterogeneous Catalysts for Catalytically Upgrading Vegetable Oils into Hydrocarbon Biofuels

Directory of Open Access Journals (Sweden)

Xianhui Zhao

2017-03-01

Full Text Available To address the issues of greenhouse gas emissions associated with fossil fuels, vegetable oilseeds, especially non-food oilseeds, are used as an alternative fuel resource. Vegetable oil derived from these oilseeds can be upgraded into hydrocarbon biofuel. Catalytic cracking and hydroprocessing are two of the most promising pathways for converting vegetable oil to hydrocarbon biofuel. Heterogeneous catalysts play a critical role in those processes. The present review summarizes current progresses and remaining challenges of vegetable oil upgrading to biofuel. The catalyst properties, applications, deactivation, and regeneration are reviewed. A comparison of catalysts used in vegetable oil and bio-oil upgrading is also carried out. Some suggestions for heterogeneous catalysts applied in vegetable oil upgrading to improve the yield and quality of hydrocarbon biofuel are provided for further research in the future.

Authentication of edible vegetable oils adulterated with used frying oil by Fourier Transform Infrared Spectroscopy.

Science.gov (United States)

Zhang, Qing; Liu, Cheng; Sun, Zhijian; Hu, Xiaosong; Shen, Qun; Wu, Jihong

2012-06-01

The application of Fourier Transform Infrared (FTIR) Spectroscopy to authenticate edible vegetable oils (corn, peanut, rapeseed and soybean oil) adulterated with used frying oil was introduced in this paper. The FTIR spectrum of oil was divided into 22 regions which corresponded to the constituents and molecular structures of vegetable oils. Samples of calibration set were classified into four categories for corn and peanut oils and five categories for rapeseed and soybean oils by cluster analysis. Qualitative analysis of validation set was obtained by discriminant analysis. Area ratio between absorption band 19 and 20 and wavenumber shift of band 19 were treated by linear regression for quantitative analysis. For four adulteration types, LODs of area ratio were 6.6%, 7.2%, 5.5%, 3.6% and wavenumber shift were 8.1%, 9.0%, 6.9%, 5.6%, respectively. The proposed methodology is a useful tool to authenticate the edible vegetable oils adulterated with used frying oil. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effect of castor oil enrichment layer produced by reaction on the properties of PLA/HDI-g-starch blends.

Science.gov (United States)

Xiong, Zhu; Zhang, Lisheng; Ma, Songqi; Yang, Yong; Zhang, Chuanzhi; Tang, Zhaobin; Zhu, Jin

2013-04-15

Blends of entirely bio-sourced polymers, namely polylactide (PLA) and starch, have been melt-compounded by lab-scale co-extruder with castor oil (CO) as a plasticizer. The enrichment of castor oil on starch had great effect on the properties of the blends. If the castor oil was mainly dispersed in PLA matrix, the properties of the blends were poor, but when the hexamethylenediisocyanate (HDI) was grafted on starch granules the ready reactions between the hydroxyl on CO and the isocyante on the HDI-grafted starch (HGSTs) brought CO molecules enriched on starch particles. DSC analysis shows that the CO layer on starch has a positive effect on the crystallization of PLA in the ternary blend. The accumulation of CO on starch greatly improves the toughness and impact strength of PLA/starch blends. The grafting content of HDI on the starch granules primarily determined the compatibility and properties of the resulted blends. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation of function-enhanced vegetable oils

Directory of Open Access Journals (Sweden)

Hiroshi Maeda

2016-01-01

Full Text Available Background: Previously, we (HM found that most commercially available edible oils, which were processed by hexane extraction followed by a number of purification steps, were extremely low in anti-peroxy radical (ROO., or radical scavenging activity. This is a great contrast to the respective virgin oils as exemplified by extra-virgin olive oil or crude rape seed oil [1-4] (Figure 1. Therefore, such highly purified oils will became prooxidant and less desirable food components in terms of health oriented diet. Oxidized oils may eventually cause DNA cleavages, modification of proteins, RNA, and lipids, as well as cellular damage, or promote inflammation and carcinogenesis at later time [5-9]. These commercial oils of low antioxidant activity may be improved by adding functionally effective antioxidative components, by using dried vegetable-waste such as tomato-juice-waste-residues and wine-ferment-waste-residues. Their antioxiative components will be transferred into the functionally poor grade edible oils, and consequently, one can improve the quality of such functionally poor oils and thereby contributing human health [2,8,9]. The purpose of this paper is to report a practical procedure to fortify functionally low grade conventional edible oils to functionally enriched edible oils using dried vegetable-waste residues such as tomato juice waste, and wine-ferment-residues, or other vegetable-waste residues. Methods: (1 Preparation and measurements of lycopene and carotenoid enriched oils. To 5.0g or 1.0g of the dried residue of tomato juice waste, 100ml of commercial rape seed (canola oil was added respectively. Each mixture was incubated at room temperature in dark for several weeks. Amount of lycopene and carotenoids extracted into the oil was monitored by increase of absorption (400-550nm and fluorescence at 470nm of carotenoid. Grape-juice ferment (wine waste was similarly prepared after hot air drying, and immersed in canola oil. (2

Dioxin monitoring in fats oils for the feed industry

NARCIS (Netherlands)

Asselt, van E.D.; Sterrenburg, P.

2011-01-01

The aim of the present project was to determine the most critical steps in the production of fats and oils. First, production processes of vegetables oils, animal fat, fish oil, biodiesel and fat blending were studied and experts from the industry as well as in-house dioxin experts were consulted to

Studies on the hypolipidemic effects of Coconut oil when blended with Tiger nut oil and fed to albino rats

Directory of Open Access Journals (Sweden)

El-Anany, A. M.

2012-09-01

Full Text Available Hyperlipidemia is a predominant risk factor for atherosclerosis and associated cardiovascular diseases (CVD. The international guidelines issued by the World Health Organization recommend a reduction in dietary saturated fat and cholesterol intake as a means to prevent hypercholesterolemia and CVD. The main objective of the current investigation was to evaluate the effects of feeding blended oils consisting of coconut oil (CNO with different proportions of Tiger nut oil (TNO on serum lipid levels in Albino rats. GLC analysis was performed to illustrate the fatty acid composition of the blended oils. Blended oils were obtained by mixing tiger nut oil with coconut oil at the volume ratios of 100:0, 70:30, 50:50, 25:75, 10:90 and 0:100. Fifty-six male albino rats were randomly divided into 7 groups of 8 rats each according to the oil type. The blended oils were fed to rats for a period of up to 10 weeks. Total cholesterol (T-Ch, high-density lipoprotein cholesterol (HDL-Ch, low-density lipoprotein cholesterol (LDL-Ch, and triglycerides (TG, were determined. The atherogenic Index (AI was calculated. The results showed that non-significant changes in all nutritional parameters were observed between the control group and the rats fed with the tested oils. The results also indicate that coconut oil had 86% saturated fatty acids. On TNO contains 66% oleic acid. Therefore, blending coconut oil with tiger nut oil can reduce the proportions of saturated to unsaturated fatty acids in CNO. The rats that were fed blended oils showed significantly reduced levels of serum cholesterol as compared to those fed CNO. The HDL levels were marginally enhanced in the rats that were fed blended oils. The total cholesterol and LDL cholesterol levels were controlled when TNO/CNO proportions varied between 25/75 and 70/30. This was reflected in the calculation of the atherogenic index. Similar changes were observed with serum triglyceride levels.

La hiperlipidemia

Carcinogenicity of petroleum lubricating oil distillates: effects of solvent refining, hydroprocessing, and blending.

Science.gov (United States)

Halder, C A; Warne, T M; Little, R Q; Garvin, P J

1984-01-01

Certain refining processes were investigated to determine their influence on the dermal carcinogenic activity of petroleum-derived lubricating oil distillates. Specifically, the effects of solvent refining, hydroprocessing, a combination of both processes, and the blending of oils processed using each technique were evaluated in standard mouse skin-painting bioassays. The refining process used as well as the level or severity of treatment greatly influenced the carcinogenic outcome of processed lubricating oils. Solvent refining at severities normally used appeared to eliminate carcinogenicity. In contrast, hydroprocessing alone at mild levels of treatment was successful only in reducing the carcinogenic potency; severe hydroprocessing conditions were necessary to eliminate carcinogenic activity without the use of additional refining processes. Carcinogenic activity could also be eliminated by following moderate solvent refining with mild hydroprocessing. Blending of hydroprocessed oils with solvent-refined oils resulted in a substantial reduction or even elimination of carcinogenic activity. However, the degree of protection obtained varied with the particular distillates used and appeared largely dependent on the inherent biological activity of the hydroprocessed oil.

Vegetable oils as lube basestocks: A review | Srivastava | African ...

African Journals Online (AJOL)

Vegetable oils are promising candidates as base fluid for eco-friendly lubricants because of their excellent lubricity, biodegradability, viscosity-temperature characteristics and low volatility. In view of agriculture based Indian economy, there is a great potential of producing vegetable oil based lubricants, which has ecological ...

Heat release and engine performance effects of soybean oil ethyl ester blending into diesel fuel

International Nuclear Information System (INIS)

Bueno, Andre Valente; Velasquez, Jose Antonio; Milanez, Luiz Fernando

2011-01-01

The engine performance impact of soybean oil ethyl ester blending into diesel fuel was analyzed employing heat release analysis, in-cylinder exergy balances and dynamometric tests. Blends with concentrations of up to 30% of soybean oil ethyl ester in volume were used in steady-state experiments conducted in a high speed turbocharged direct injection engine. Modifications in fuel heat value, fuel-air equivalence ratio and combustion temperature were found to govern the impact resulting from the addition of biodiesel on engine performance. For the analyzed fuels, the 20% biodiesel blend presented the best results of brake thermal efficiency, while the 10% biodiesel blend presented the best results of brake power and sfc (specific fuel consumption). In relation to mineral diesel and in full load conditions, an average increase of 4.16% was observed in brake thermal efficiency with B20 blend. In the same conditions, an average gain of 1.15% in brake power and a reduction of 1.73% in sfc was observed with B10 blend.

Fast-HPLC Fingerprinting to Discriminate Olive Oil from Other Edible Vegetable Oils by Multivariate Classification Methods.

Science.gov (United States)

Jiménez-Carvelo, Ana M; González-Casado, Antonio; Pérez-Castaño, Estefanía; Cuadros-Rodríguez, Luis

2017-03-01

A new analytical method for the differentiation of olive oil from other vegetable oils using reversed-phase LC and applying chemometric techniques was developed. A 3 cm short column was used to obtain the chromatographic fingerprint of the methyl-transesterified fraction of each vegetable oil. The chromatographic analysis took only 4 min. The multivariate classification methods used were k-nearest neighbors, partial least-squares (PLS) discriminant analysis, one-class PLS, support vector machine classification, and soft independent modeling of class analogies. The discrimination of olive oil from other vegetable edible oils was evaluated by several classification quality metrics. Several strategies for the classification of the olive oil were used: one input-class, two input-class, and pseudo two input-class.

Natural Organochlorines as Precursors of 3-Monochloropropanediol Esters in Vegetable Oils.

Science.gov (United States)

Tiong, Soon Huat; Saparin, Norliza; Teh, Huey Fang; Ng, Theresa Lee Mei; Md Zain, Mohd Zairey Bin; Neoh, Bee Keat; Md Noor, Ahmadilfitri; Tan, Chin Ping; Lai, Oi Ming; Appleton, David Ross

2018-01-31

During high-temperature refining of vegetable oils, 3-monochloropropanediol (3-MCPD) esters, possible carcinogens, are formed from acylglycerol in the presence of a chlorine source. To investigate organochlorine compounds in vegetable oils as possible precursors for 3-MCPD esters, we tested crude palm, soybean, rapeseed, sunflower, corn, coconut, and olive oils for the presence of organochlorine compounds. Having found them in all vegetable oils tested, we focused subsequent study on oil palm products. Analysis of the chlorine isotope mass pattern exhibited in high-resolution mass spectrometry enabled organochlorine compound identification in crude palm oils as constituents of wax esters, fatty acid, diacylglycerols, and sphingolipids, which are produced endogenously in oil palm mesocarp throughout ripening. Analysis of thermal decomposition and changes during refining suggested that these naturally present organochlorine compounds in palm oils and perhaps in other vegetable oils are precursors of 3-MCPD esters. Enrichment and dose-response showed a linear relationship to 3-MCPD ester formation and indicated that the sphingolipid-based organochlorine compounds are the most active precursors of 3-MCPD esters.

Combustion Characteristics of CI Diesel Engine Fuelled With Blends of Jatropha Oil Biodiesel

Science.gov (United States)

Singh, Manpreet; Yunus Sheikh, Mohd.; Singh, Dharmendra; Nageswara rao, P.

2018-03-01

Jatropha Curcas oil is a non-edible oil which is used for Jatropha biodiesel (JBD) production. Jatropha biodiesel is produced using transesterification technique and it is used as an alternative fuel in CI diesel engine without any hardware modification. Jatropha biodiesel is used in CI diesel engine with various volumetric concentrations (blends) such as JBD5, JBD15, JBD25, JBD35 and JBD45. The combustion parameters such as in-cylinder pressure, rate of pressure rise, net heat release, cumulative heat release, mass fraction burned are analyzed and compared for all blends combustion data with mineral diesel fuel (D100).

Utilization of some non-edible oil for biodiesel production ...

African Journals Online (AJOL)

In this work, the production of biodiesel from four sources of non-edible oils, namely jatropha, animal fat, waste vegetable oil and castor oil was carried out. It was done using an acid esterification process followed by alkali transesterification in the laboratory. Subsequently the physicochemical properties for four blends B100 ...

Thermal profiles, crystallization behaviors and microstructure of diacylglycerol-enriched palm oil blends with diacylglycerol-enriched palm olein.

Science.gov (United States)

Xu, Yayuan; Zhao, Xiaoqing; Wang, Qiang; Peng, Zhen; Dong, Cao

2016-07-01

To elucidate the possible interaction mechanisms between DAG-enriched oils, this study investigated how mixtures of DAG-enriched palm-based oils influenced the phase behavior, thermal properties, crystallization behaviors and the microstructure in binary fat blends. DAG-enriched palm oil (PO-DAGE) was blended with DAG-enriched palm olein (POL-DAGE) in various percentages (0%, 10%, 30%, 50%, 70%, 90%, 100%). Based on the observation of iso-solid diagram and phase diagram, the binary mixture of PO-DAGE/POL-DAGE showed a better compatibility in comparison with their corresponding original blends. DSC thermal profiles exhibited that the melting and crystallization properties of PO-DAGE/POL-DAGE were distinctively different from corresponding original blends. Crystallization kinetics revealed that PO-DAGE/POL-DAGE blends displayed a rather high crystallization rate and exhibited no spherulitic crystal growth. From the results of polarized light micrographs, PO-DAGE/POL-DAGE blends showed more dense structure with very small needle-like crystals than PO/POL. X-ray diffraction evaluation revealed when POL-DAGE was added in high contents to PO-DAGE, above 30%, β-polymorph dominated, and the mount of β' forms crystals was decreasing. Copyright © 2016 Elsevier Ltd. All rights reserved.

Stability evaluation and chemical characterization of different vegetable oils viewing the search for candidates for certified reference materials for bio diesel; Avaliacao da estabilidade e caracterizacao quimica de diferentes oleos vegetais visando a busca de candidatos a materiais de referencia certificado (MRC) para biodiesel

Energy Technology Data Exchange (ETDEWEB)

Cruz, Georgiana F. da; Fonseca, Mauricio G.; Goncalves, Lenise V.F.; Silva, Regina Celia F. da; Silva, Fernanda M.R. da; Rodrigues, Janaina M. [Instituto Nacional de Metrologia, Normalizacao e Qualidade Industrial (LABOR/INMETRO), Duque de Caxias, RJ (Brazil). Lab. de Analises Organicas; Leal, Rodrigo V.P. [Instituto Nacional de Metrologia, Normalizacao e Qualidade Industrial (LAMBOC/INMETRO), Duque de Caxias, RJ (Brazil). Lab. de Motores, Combustiveis e Lubrificantes], Email: rvleal@inmetro.gov.br; Cunha, Valnei S. [Instituto Nacional de Metrologia, Normalizacao e Qualidade Industrial (DIMCI/INMETRO), Duque de Caxias, RJ (Brazil). Diretoria de Metrologia Cientifica e Industrial

2009-07-01

Viewing the characterization of the various vegetable oils aiming to obtain a data bank that allows the production of certified reference materials for bio diesel of different blends, a study of chemical-physical characterization of different oils and derivative of bio diesel.

Taxonomic perspective of plant species yielding vegetable oils used ...

African Journals Online (AJOL)

A search conducted to determine the plants yielding vegetable oils resulted in 78 plant species with potential use in cosmetics and skin care products. The taxonomic position of these plant species is described with a description of vegetable oils from these plants and their use in cosmetic and skin care products.

Vegetable oils as fuels and lubrificants: Commercialization problematics

International Nuclear Information System (INIS)

Bartolelli, V.

1992-01-01

The aim of this paper is to assess the commercialization feasibility of vegetable oils as industrial fuels and lubricants. The paper also discusses what should be the suitable mix of Italian Government agricultural, environmental and fiscal strategies to support and encourage the production and use of industrial vegetable fuel oils and lubricants. It points out the main advantages of bio-fuel oils - they are much less polluting than conventional fossil fuel oils and can be produced domestically, thus reducing national dependency on foreign energy imports and increasing employment opportunities. The major obstacle to their development is identified as being the creation of suitable pricing and fiscal policies in harmony with traditional energy markets

Experiment on the Effects of Storage Duration of Biodiesel produced from Crude Palm Oil, Waste Cooking oil and Jatropha

Science.gov (United States)

Nanihar, Nadiarulah; Khalid, Amir; Mustaffa, Norrizal; Jaat, Norrizam; Sapit, Azwan; Razali, Azahari; Sunar, Norshuhaila Mohamed

2017-10-01

Biodiesel based on vegetable oil is an alternative that had various advantage in term of sustainability and environmental attractive compare to others conventional diesel. Biodiesel is product of any fat or oil that derived from any organic sources through a refinery process called transesterification process. This research investigates the effects of storage duration and variant ambient condition on the biodiesel properties and characteristics. In this study, there are three types of blending which is 5vol% blends ( 5vol% plant oil 95vol% diesel), 10vol% blending (10vol% plant oil and 90vol% diesel) and 15vol% blending (15vol% plant oil and 85vol% diesel) each called CPO5 (crude palm oil 5vol%), CPO10 (crude palm oil 10vol%),CPO15 (crude palm oil 15vol%), JO5 (jatropha oil 5vol%), JO10 (jatropha oil 10vol%),and JO15 (jatropha oil 15vol%) respectively. Biodiesel samples were stored at indoor condition and outdoor condition for a 3 months period. The fuel properties such as acid value, viscosity, density, water content and flash point are observed with the laboratory instrument. Flash point value and water content increased under both of indoor and outdoor condition and a steady data for viscosity and density. However, acid value at indoor condition nearly constant but increased dramatically for outdoor condition over the time.

Determination of lipid oxidation products in vegetable oils and marine omega-3 supplements.

Science.gov (United States)

Halvorsen, Bente Lise; Blomhoff, Rune

2011-01-01

There is convincing evidence that replacing dietary saturated fats with polyunsaturated fats (PUFA) decreases risk of cardiovascular diseases. Therefore, PUFA rich foods such as vegetable oils, fatty fish, and marine omega-3 supplements are recommended. However, PUFA are easily oxidizable and there is concern about possible negative health effects from intake of oxidized lipids. Little is known about the degree of lipid oxidation in such products. To assess the content of lipid oxidation products in a large selection of vegetable oils and marine omega-3 supplements available in Norway. Both fresh and heated vegetable oils were studied. A large selection of commercially available vegetable oils and marine omega-3 supplements was purchased from grocery stores, pharmacies, and health food stores in Norway. The content of lipid oxidation products were measured as peroxide value and alkenal concentration. Twelve different vegetable oils were heated for a temperature (225°C) and time (25 minutes) resembling conditions typically used during cooking. The peroxide values were in the range 1.04-10.38 meq/kg for omega-3 supplements and in the range 0.60-5.33 meq/kg for fresh vegetable oils. The concentration range of alkenals was 158.23-932.19 nmol/mL for omega-3 supplements and 33.24-119.04 nmol/mL for vegetable oils. After heating, a 2.9-11.2 fold increase in alkenal concentration was observed for vegetable oils. The contents of hydroperoxides and alkenals in omega-3 supplements are higher than in vegetable oils. After heating vegetable oils, a large increase in alkenal concentration was observed.

Undesirable substances in vegetable oils: anything to declare?

Directory of Open Access Journals (Sweden)

Lacoste Florence

2014-01-01

Full Text Available The presence of undesirable compounds in vegetable and animal oils and fats may have many different origins. Although the potential toxicity of most of these undesirable compounds is real, poisoning risks are rather limited due to the efficient elimination during oil-refining steps, careful conditioning, choice of efficient packaging and industrial quality control management. However the research of contaminants is part of multiple controls conducted by fat and oil industry to verify the conformity of products placed on the market in relation to regulations such as the European commission regulation EC No. 1881/2006 setting maximum levels for some contaminants in food as lead, some mycotoxins, dioxins, polychlorobiphenyls, benzo[a]pyrene. In the absence of regulation, the detection of contaminants must be addressed in partnership with authorities according to the toxicity of molecules. The controls are not confined to environmental contaminants. They also include compounds that can be formed during the production process of vegetable oils such as esters of 3-monochloropropanediol. This article focuses more particularly on heavy metals, polycyclic aromatic hydrocarbons, mineral oils, phthalates and 3-MCPD or glycidyl esters. Aspects such as methods for analysis, limits fixed by EC regulation and occurrence in vegetable oils are discussed.

Vegetable oil basestocks for lubricants

Directory of Open Access Journals (Sweden)

Garcés, Rafael

2011-03-01

Full Text Available The use of vegetable biodegradable basestocks for lubricant oils present several advantages over the much more extended mineral bases. These advantages refer to biodegradability, a renewable feedstock of local production, lubricant and viscosity index and lower costs than synthetic lubricant bases. Despite these benefits, their use in industry and motor vehicles is not yet extensive due their lower stability and higher pour points. Vegetable oils are esters of fatty acids and glycerol, and their physicochemical properties rely mainly on the composition of their acyl moieties. Thus, to assure the maximum levels of stability while maintaining acceptable behavior at low temperatures, monounsaturated fatty acids are preferred for this purpose. The presence of natural antioxidants also improves the properties of these vegetable based stocks as lubricants. These oils usually require additives to improve their viscosity value, oxidative stability and properties at low temperatures. In the present work, the different sources of vegetable oils appropriate for biolubricant production were reviewed. Their properties and the future improvement of the oil bases, oil based stock production, uses and additives are discussed.

El uso de bases vegetales biodegradables para aceites lubricantes presenta varias ventajas sobre las mucho más extendidas bases minerales. Estas ventajas se centran sobre todo en su biodegradabilidad, en ser un recurso renovable de producción local, en su lubricidad y en su índice de viscosidad, presentando además costes más bajos que las bases sintéticas. Sin embargo, estas ventajas no han extendido el uso de bases vegetales ni en industria ni en automoción debido a su menor estabilidad y sus mayores puntos críticos de fluidez. Los aceites vegetales son ésteres de ácidos grasos y glicerol y sus propiedades físico-químicas dependen principalmente de su composición acílica. Así, para asegurar los máximos niveles de

Genetically engineered plants with increased vegetative oil content

Science.gov (United States)

Benning, Christoph

2017-05-23

The invention relates to genetically modified agricultural plants with increased oil content in vegetative tissues, as well as to expression systems, plant cells, seeds and vegetative tissues related thereto.

Operation variables in transesterification of vegetable oil: an enzymatic catalysis review

Directory of Open Access Journals (Sweden)

Andrés Felipe Rojas González

2010-01-01

Full Text Available This paper presents the results of a literature review regarding how operating conditions influence vegetable oil enzymatic transesterification yield. The following parameters were studied: temperature and time reaction, alcohol: oil molar ratio, alcohol type, biocatalyst type and concentration, solvent, mixed intensity, reagent purity and free fatty acid and moisture concentration. Yields greater than 90% can be achieved in the enzymatic catalyst of vegetable oil using 35-50°C temperatures, long time reactions (7- 90h and a 3:1alcohol: vegetable oil molar ratio; however, such values would intrinsically depend on the type of lipase and oil u- sed. It was also found that free fatty acid and moisture concentration were parameters which did not require rigorous control due to high enzyme specificity. Lipases immobilised from Pseudomona cepacia bacteria and Rhizopus orizae fungi were most used in vegetable oil enzymatic transesterification.

Effects of Biodiesel Blend on Marine Fuel Characteristics for Marine Vessels

Directory of Open Access Journals (Sweden)

Cherng-Yuan Lin

2013-09-01

Full Text Available Biodiesel produced from vegetable oils, animal fats and algae oil is a renewable, environmentally friendly and clean alternative fuel that reduces pollutants and greenhouse gas emissions in marine applications. This study investigates the influence of biodiesel blend on the characteristics of residual and distillate marine fuels. Adequate correlation equations are applied to calculate the fuel properties of the blended marine fuels with biodiesel. Residual marine fuel RMA has inferior fuel characteristics compared with distillate marine fuel DMA and biodiesel. The flash point of marine fuel RMA could be increased by 20% if blended with 20 vol% biodiesel. The sulfur content of residual marine fuel could meet the requirement of the 2008 MARPOL Annex VI Amendment by blending it with 23.0 vol% biodiesel. In addition, the kinematic viscosity of residual marine fuel could be reduced by 12.9% and the carbon residue by 23.6% if 20 vol% and 25 vol% biodiesel are used, respectively. Residual marine fuel blended with 20 vol% biodiesel decreases its lower heating value by 1.9%. Moreover, the fuel properties of residual marine fuel are found to improve more significantly with biodiesel blending than those of distillate marine fuel.

Macauba: a promising tropical palm for the production of vegetable oil

Directory of Open Access Journals (Sweden)

Colombo Carlos Augusto

2018-01-01

Full Text Available The growing global demand for vegetable oils for food and for replacing fossil fuels leads to increased oilseeds production. Almost 122 of the current 187 million tons of vegetable oils produced in the world correspond to palm and soybean oils. The oil palm is cultivated in the tropical zone, in areas formerly occupied by forests, and soybean oil is a by-product of protein meal production. The diversification of raw materials for the vegetable oil market is thus strategic for both food and non-food sectors. Sources for vegetable oil should be economically competitive and provide sustainability indexes higher than that provided by oil palm and soybean. In this context, we describe the potential of Acrocomia aculeata, popularly known as macauba. Macauba is an American palm from the tropical zones which presents oil productivity and quality similar to that of the oil palm. It grows spontaneously in a wide range of environments and it is not very water demanding. Macauba palm has a high potential for oil production and for diversification of co-products with some potential of value aggregation. Such a perennial and sustainable species will probably fulfill the requirements to become an important new commercial oilseed crop.

Low density polyethylene (LDPE) / poli (3-hydroxy-butyrate) (PHB) blends filled with castor oil cake

International Nuclear Information System (INIS)

Rocha, M.C.G.; Oliveira, C.I.R. de; Sanches, M.C.; Coelho, N.N.

2014-01-01

Blends of PHB and LDPE were prepared by melt mixing in a Haake internal mixer. Castor oil pressed cake was used as filler for the blends. In order to improve the interfacial adhesion between the filler and the polymers, a mercerization process with 5% NaOH solution was employed. This process was evaluated by several techniques such as: X-Ray diffraction, infrared spectroscopy and scanning electron microscopy (SEM). The mechanical properties were evaluated by traditional tensile stress-strain tests (ASTM D- 638). The obtained results showed that the mercerization process leads to better adhesion properties. The Young Modulus of the blends presented a tendency to increase with the addition of the castor oil cake.(author)

Vegetable oils in the agriculture. Experience reports; Pflanzenoel als Kraftstoff in der Landwirtschaft. Erfahrungsberichte

Energy Technology Data Exchange (ETDEWEB)

Kemnitz, Dietmar [Fachagentur Nachwachsende Rohstoffe e.V., Guelzow (Germany); Paul, Nicole [Fachagentur Nachwachsende Rohstoffe e.V., Guelzow (Germany); WPR COMMUNICATION GmbH und Co. KG, Koenigswinter/Bonn (Germany); Wichmann, Volker; Schuemann, Ulrike [Rostock Univ. (Germany); Maurer, Karl [Hohenheim Univ. (Germany); Remmele, Edgar [Technologie- und Foerderzentrum Straubing (Germany)

2006-08-15

In the agriculture, bio fuels increasingly meet with great interest. The use of bio diesel and vegetable oil as alternative fuels in diesel engines requires clear technical adjustments. The brochure under consideration reports on realizations of farmers who switched their tractors to an operation with vegetable oils. The brochure consists of the following contributions: (a) Employment of vegetable oil as fuel in the agriculture (empiric reports of farmers); (b) Re-equipment on operation with vegetable oil (empiric reports of reequipping persons); (c) Scientifically accompanying research of re-equipment (results of a 100-tractor-demonstration project); (d) Mixtures of plant oil and diesel fuel (results from engine test stand investigations); (e) Production of vegetable oil (experiences from an oil mill operator); (f) scientifically accompanying research for the production of vegetable oils (references to the production of rapeseed oil fuel according to the standard DIN 51605); (g) Hints and notes for the practice; (h) Fuel filling stations for self-consumers and storage of vegetable oil; (i) FNR funding programs bio fuels in the agriculture; (j) Adresses and contact persons.

Determination of lipid oxidation products in vegetable oils and marine omega-3 supplements

Directory of Open Access Journals (Sweden)

Rune Blomhoff

2011-06-01

Full Text Available Background : There is convincing evidence that replacing dietary saturated fats with polyunsaturated fats (PUFA decreases risk of cardiovascular diseases. Therefore, PUFA rich foods such as vegetable oils, fatty fish, and marine omega-3 supplements are recommended. However, PUFA are easily oxidizable and there is concern about possible negative health effects from intake of oxidized lipids. Little is known about the degree of lipid oxidation in such products. Objective : To assess the content of lipid oxidation products in a large selection of vegetable oils and marine omega-3 supplements available in Norway. Both fresh and heated vegetable oils were studied. Design : A large selection of commercially available vegetable oils and marine omega-3 supplements was purchased from grocery stores, pharmacies, and health food stores in Norway. The content of lipid oxidation products were measured as peroxide value and alkenal concentration. Twelve different vegetable oils were heated for a temperature (225°C and time (25 minutes resembling conditions typically used during cooking. Results : The peroxide values were in the range 1.04–10.38 meq/kg for omega-3 supplements and in the range 0.60–5.33 meq/kg for fresh vegetable oils. The concentration range of alkenals was 158.23–932.19 nmol/mL for omega-3 supplements and 33.24–119.04 nmol/mL for vegetable oils. After heating, a 2.9–11.2 fold increase in alkenal concentration was observed for vegetable oils. Conclusions : The contents of hydroperoxides and alkenals in omega-3 supplements are higher than in vegetable oils. After heating vegetable oils, a large increase in alkenal concentration was observed.

Positional Distribution of Fatty Acids in Triacylglycerols and Phospholipids from Fillets of Atlantic Salmon (Salmo Salar) Fed Vegetable and Fish Oil Blends.

Science.gov (United States)

Ruiz-Lopez, Noemi; Stubhaug, Ingunn; Ipharraguerre, Ignacio; Rimbach, Gerald; Menoyo, David

2015-07-10

The nutritional and functional characteristics of dietary fat are related to the fatty acid (FA) composition and its positional distribution in the triacylglycerol (TAG) fraction. Atlantic salmon is an important source of healthy long chain omega 3 FA (particularly, eicosapentaenoic (EPA) and docoxahexaenoic (DHA) acids). However, the impact of lipid sources in salmon feeds on the regiospecificity of FA in the fish TAG remains to be explored. The present study determines the effect of feeding salmon with blends of palm, rapeseed, and fish oil, providing two different EPA + DHA concentrations (high: H-ED 10.3% and low: L-ED 4.6%) on the fillet lipid class composition and the positional distribution of FA in TAG and phospholipids. The regiospecific analysis of fillet TAG showed that around 50% of the EPA and around 80% of DHA was located in the sn-2 position. The positional distribution of FA in phosphatidylcholine (PC), showed that around 80% of the EPA and around 90% of DHA were located in the sn-2. Fish fed the vegetable-rich diets showed higher EPA in the sn-2 position in PC (77% vs. 83% in the H-ED and L-ED diets, respectively) but similar DHA concentrations. It is concluded that feeding salmon with different EPA + DHA concentrations does not affect their positional distribution in the fillet TAG.

Positional Distribution of Fatty Acids in Triacylglycerols and Phospholipids from Fillets of Atlantic Salmon (Salmo Salar Fed Vegetable and Fish Oil Blends

Directory of Open Access Journals (Sweden)

Noemi Ruiz-Lopez

2015-07-01

Full Text Available The nutritional and functional characteristics of dietary fat are related to the fatty acid (FA composition and its positional distribution in the triacylglycerol (TAG fraction. Atlantic salmon is an important source of healthy long chain omega 3 FA (particularly, eicosapentaenoic (EPA and docoxahexaenoic (DHA acids. However, the impact of lipid sources in salmon feeds on the regiospecificity of FA in the fish TAG remains to be explored. The present study determines the effect of feeding salmon with blends of palm, rapeseed, and fish oil, providing two different EPA + DHA concentrations (high: H-ED 10.3% and low: L-ED 4.6% on the fillet lipid class composition and the positional distribution of FA in TAG and phospholipids. The regiospecific analysis of fillet TAG showed that around 50% of the EPA and around 80% of DHA was located in the sn-2 position. The positional distribution of FA in phosphatidylcholine (PC, showed that around 80% of the EPA and around 90% of DHA were located in the sn-2. Fish fed the vegetable-rich diets showed higher EPA in the sn-2 position in PC (77% vs. 83% in the H-ED and L-ED diets, respectively but similar DHA concentrations. It is concluded that feeding salmon with different EPA + DHA concentrations does not affect their positional distribution in the fillet TAG.

Comparison between jojoba oil and other vegetable oils as a substitute to petroleum

Energy Technology Data Exchange (ETDEWEB)

El Kinawy, O. [National Research centre, Dokki, Cairo (Egypt)

2004-06-15

Jojoba oil and other vegetable oils, such as soybean, sunflower and castor oils, were evaluated to be used as lubricants. Three standard mineral lubricating oils were considered in this study as reference. The essential parameters tested for comparison were the oil viscosity, viscosity index, and viscosity--temperature and shear rate--shear stress relationships. The effect of excessive heating on the vegetable oils' stability was studied and the corresponding parameters were also measured. Jojoba oil was found to be the best among all tested oils, whereas it gave the minimum change in viscosity gradient and hence the highest viscosity index. There was a linear relation between shear rate and shear stress of all oils before and after heat deterioration. Therefore, these oils were considered as Newtonion liquids. However, the oil viscosity, as well as the rate of viscosity variation with temperature, ({delta}{sup '}{eta}/{delta}{tau}) were affected by heat deterioration being lowered in value, in case of jojoba oil, and higher value, in case of castor oil. Jojoba oil was examined for other important properties for its use as a lubricant, such as refractive index, acid value, peroxide value, saponification value, iodine value, flash, fire and pour points. (author)

Experimental data of thermal cracking of soybean oil and blends with hydrogenated fat

Directory of Open Access Journals (Sweden)

R.F. Beims

2018-04-01

Full Text Available This article presents the experimental data on the thermal cracking of soybean oil and blends with hydrogenated fat. Thermal cracking experiments were carried out in a plug flow reactor with pure soybean oil and two blends with hydrogenated fat to reduce the degree of unsaturation of the feedstock. The same operational conditions was considered. The data obtained showed a total aromatics content reduction by 14% with the lowest degree of unsaturation feedstock. Other physicochemical data is presented, such as iodine index, acid index, density, kinematic viscosity. A distillation curve was carried out and compared with the curve from a petroleum sample.

Technical aspects of biodiesel production from vegetable oils

Directory of Open Access Journals (Sweden)

Krishnakumar Janahiraman

2008-01-01

Full Text Available Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experimental research, edible rice bran oil used as test material and converted into methyl ester and non-edible jatropha vegetable oil is converted into jatropha oil methyl ester, which are known as biodiesel and they are prepared in the presence of homogeneous acid catalyst and optimized their operating parameters like reaction temperature, quantity of alcohol and the catalyst requirement, stirring rate and time of esterification. In the second step, the physical properties such as density, flash point, kinematic viscosity, cloud point, and pour point were found out for the above vegetable oils and their methyl esters. The same characteristics study was also carried out for the diesel fuel for obtaining the baseline data for analysis. The values obtained from the rice bran oil methyl ester and jatropha oil methyl ester are closely matched with the values of conventional diesel and it can be used in the existing diesel engine without any hardware modification. In the third step the storage characteristics of biodiesel are also studied. .

Biodiesel in Belgium. From rapeseed oil to used vegetable oils

International Nuclear Information System (INIS)

Pelkmans, L.

1997-01-01

There are two motives for the search for alternative motor fuels: reducing the growing pressure of traffic on environment, and looking for a replacement for petrol and diesel oil that are bound to be worn-out in a few decades. A promising alternative motor fuel is biodiesel. The author's institute is involved in its second biodiesel demonstration project. In the first project RME (rapeseed methyl ester) was used undiluted in five passenger cars for two years. There were no technical problems and a clear environmental advantage was noticed. However, the price remains a problem. The use of waste vegetable oils for the production of biodiesel could help to overcome this problem. Therefore, a second biodiesel demonstration project was started in which UVOME (used vegetable oil methyl ester) is used. The preliminary results show a great similarity with the RME results and no technical problems in real life use. 1 fig., 1 tab., 5 refs

Remediation of trichloroethylene-contaminated soils by star technology using vegetable oil smoldering.

Science.gov (United States)

Salman, Madiha; Gerhard, Jason I; Major, David W; Pironi, Paolo; Hadden, Rory

2015-03-21

Self-sustaining treatment for active remediation (STAR) is an innovative soil remediation approach based on smoldering combustion that has been demonstrated to effectively destroy complex hydrocarbon nonaqueous phase liquids (NAPLs) with minimal energy input. This is the first study to explore the smoldering remediation of sand contaminated by a volatile NAPL (trichloroethylene, TCE) and the first to consider utilizing vegetable oil as supplemental fuel for STAR. Thirty laboratory-scale experiments were conducted to evaluate the relationship between key outcomes (TCE destruction, rate of remediation) to initial conditions (vegetable oil type, oil: TCE mass ratio, neat versus emulsified oils). Several vegetable oils and emulsified vegetable oil formulations were shown to support remediation of TCE via self-sustaining smoldering. A minimum concentration of 14,000 mg/kg canola oil was found to treat sand exhibiting up to 80,000 mg/kg TCE. On average, 75% of the TCE mass was removed due to volatilization. This proof-of-concept study suggests that injection and smoldering of vegetable oil may provide a new alternative for driving volatile contaminants to traditional vapour extraction systems without supplying substantial external energy. Copyright © 2014 Elsevier B.V. All rights reserved.

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends.

Science.gov (United States)

Botella, Lucía; Stankovikj, Filip; Sánchez, José L; Gonzalo, Alberto; Arauzo, Jesús; Garcia-Pérez, Manuel

2018-01-01

The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325°C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here.

Bio-oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

Science.gov (United States)

Botella, Lucía; Stankovikj, Filip; Sánchez, José L.; Gonzalo, Alberto; Arauzo, Jesús; Garcia-Pérez, Manuel

2018-04-01

The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325 °C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here.

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

Directory of Open Access Journals (Sweden)

Lucía Botella

2018-04-01

Full Text Available The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325°C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons, middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here.

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

Science.gov (United States)

Botella, Lucía; Stankovikj, Filip; Sánchez, José L.; Gonzalo, Alberto; Arauzo, Jesús; Garcia-Pérez, Manuel

2018-01-01

The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325°C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here. PMID:29675406

Photolysis of polychlorinated dibenzo-p-dioxins and dibenzofurans dissolved in vegetable oils: influence of oil quality

International Nuclear Information System (INIS)

Isosaari, Pirjo; Laine, Olli; Tuhkanen, Tuula; Vartiainen, Terttu

2005-01-01

Sunlight or ultraviolet light irradiation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the presence of vegetable oil offers a potential method for the cleanup of contaminated soil. In this study, the effects of different types of vegetable oils on the photochemical degradation of 1,2,3,4,6,7,8-heptachlorodibenzofuran and heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-HpCDF/HpCDD) were investigated in the laboratory. Using a blacklight lamp as a source of ultraviolet light, 93-100% of 1,2,3,4,6,7,8-HpCDF degraded in 60 min in rapeseed oil, extra virgin olive oil and olive oil. Less degradation occurred in palm oil (59%), toluene (39%) and hexane (20%). The better degradation in vegetable oils in comparison with organic solvents was attributed to the photooxidation of lipids producing hydrogen for PCDD/F dechlorination. In addition to the hydrogen donor capacity, permeability of ultraviolet light was involved in the differences between vegetable oils. α-Tocopherol and chlorophyll did not influence the performance of oil at concentrations normally present in vegetable oils, whereas β-carotene had an inhibitory effect on the degradation of 1,2,3,4,6,7,8-HpCDF. Up to 28% of the degradation products of 1,2,3,4,6,7,8-HpCDF were formed via the dechlorination pathway. Products included both toxic (2,3,7,8-chlorinated) and non-toxic PCDD/Fs, the toxic PCDD/Fs being more stable. Irradiation of 1,2,3,4,6,7,8-HpCDD yielded only non-toxic dechlorination products. Polychlorinated hydroxybiphenyls (OH-PCBs), polychlorinated dihydroxybiphenyls (DOH-PCBs) and polychlorinated hydroxydiphenylethers (OH-PCDEs) containing one to seven chlorine atoms were not detected in irradiated HpCDF/HpCDD samples

Photolysis of polychlorinated dibenzo-p-dioxins and dibenzofurans dissolved in vegetable oils: influence of oil quality

Energy Technology Data Exchange (ETDEWEB)

Isosaari, Pirjo [National Public Health Institute, Department of Environmental Health, P.O. Box 95, FI-70701 Kuopio (Finland)]. E-mail: pirjo.isosaari@ktl.fi; Laine, Olli [National Public Health Institute, Department of Environmental Health, P.O. Box 95, FI-70701 Kuopio (Finland); Tuhkanen, Tuula [Tampere University of Technology, Environmental Engineering and Biotechnology, P.O. Box 541, FI-33101 Tampere (Finland); Vartiainen, Terttu [National Public Health Institute, Department of Environmental Health, P.O. Box 95, FI-70701 Kuopio (Finland); University of Kuopio, Department of Environmental Sciences, P.O. Box 1627, Kuopio, FI-70211 Kuopio (Finland)

2005-03-20

Sunlight or ultraviolet light irradiation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the presence of vegetable oil offers a potential method for the cleanup of contaminated soil. In this study, the effects of different types of vegetable oils on the photochemical degradation of 1,2,3,4,6,7,8-heptachlorodibenzofuran and heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-HpCDF/HpCDD) were investigated in the laboratory. Using a blacklight lamp as a source of ultraviolet light, 93-100% of 1,2,3,4,6,7,8-HpCDF degraded in 60 min in rapeseed oil, extra virgin olive oil and olive oil. Less degradation occurred in palm oil (59%), toluene (39%) and hexane (20%). The better degradation in vegetable oils in comparison with organic solvents was attributed to the photooxidation of lipids producing hydrogen for PCDD/F dechlorination. In addition to the hydrogen donor capacity, permeability of ultraviolet light was involved in the differences between vegetable oils. {alpha}-Tocopherol and chlorophyll did not influence the performance of oil at concentrations normally present in vegetable oils, whereas {beta}-carotene had an inhibitory effect on the degradation of 1,2,3,4,6,7,8-HpCDF. Up to 28% of the degradation products of 1,2,3,4,6,7,8-HpCDF were formed via the dechlorination pathway. Products included both toxic (2,3,7,8-chlorinated) and non-toxic PCDD/Fs, the toxic PCDD/Fs being more stable. Irradiation of 1,2,3,4,6,7,8-HpCDD yielded only non-toxic dechlorination products. Polychlorinated hydroxybiphenyls (OH-PCBs), polychlorinated dihydroxybiphenyls (DOH-PCBs) and polychlorinated hydroxydiphenylethers (OH-PCDEs) containing one to seven chlorine atoms were not detected in irradiated HpCDF/HpCDD samples.

Salt marsh recovery from a crude oil spill: Vegetation, oil weathering, and response

International Nuclear Information System (INIS)

Hoff, R.Z.; Shigenaka, G.; Henry, C.B. Jr.

1993-01-01

When a spill of Prudhoe Bay crude oil covered a fringing Salicornia virginica marsh in Fidalgo Bay, Washington (northern Puget Sound) in February 1991, response personnel used several low-impact techniques to remove oil from the marsh, and minimized access by cleanup workers. Following the response, a monitoring program was established to track marsh recovery, and to document the effectiveness of the response techniques used and their impacts on the marsh. Through monthly sampling over a 16-month period, vegetative growth was monitored and chemical degradation of remaining oil was tracked. Sampling was conducted along transects located in four areas affected in different ways by the spill, including an oiled, trampled section; an oiled, vacuumed section; and an oiled, washed, and vacuumed section. In addition, a control transect was established in an unoiled adjacent marsh. The study included both biological and chemical components. Biological measurements included percent cover of live vegetation (sampled monthly) and below-ground plant biomass (sampled at the beginning of each growing season in April 1991 and April 1992). Sediment samples included surface sediment (monthly) and core samples collected at the beginning and end of the growing seasons. Sediment samples were analyzed using gas chromatography/mass spectroscopy, and indicator compounds were tracked to determine rates of oil degradation. Results from 16 months of post-spill monitoring show that foot trampling was most detrimental to marsh plants, while washing with vacuuming removed the most oil and minimized adverse impacts to vegetation. Dense clay substrate helped prevent oil from penetrating the sediment, thus minimizing acute toxic effects from oil exposure to marsh plant rootstock. By the second growing season post-spill, Salicornia and other marsh plants were growing in all areas except one heavily oiled patch

Lipid Peroxidation in Rat Liver using Different Vegetable Oils

International Nuclear Information System (INIS)

Eqbal Dauqan; Aminah Abdullah; Halimah Abdullah Sani

2013-01-01

The objective of the study was to evaluate the effect of different vegetable oils (Red Palm Olien (RPO), Palm Olein (PO), Corn Oil (CO) and Coconut Oil on lipid peroxidation of rat liver. One hundred and thirty two Sprague Dawley male rats were randomly divided into two groups. The first group contains seventy two rats were divided into twelve groups of 6 rats per group and were treated with different concentrations of RPO (5 %, 10 % and 15 %) for 2, 4 and 8 weeks. The second group contains sixty male rats were randomly divided into ten groups of 6 rats per group and were treated with 15 % of RPO, PO, CO and COC for 4 and 8 weeks. The results shows that after 8 weeks of treatment the malonaldehyde (MDA) value in RPO group was significantly lower (P≤0.05) than control or vegetable oils studied. These experiments suggested that red palm olein antioxidants present in rat diets may better attenuate peroxyl radical than other vegetable oil studied. (author)

Antimicrobial Activity and the Chemical Composition of the Volatile Oil Blend from Allium sativum (Garlic Clove) and Citrus reticulata (Tangerine Fruit)

OpenAIRE

OO Johnson; GA Ayoola; T Adenipekun

2013-01-01

The synergistic effect in the antimicrobial activity of the volatile oil blend from Garlic clove (Allium sativum) and tangerine fruits (Citrus reticulata) were investigated and compared to antimicrobial activity when the individual volatile oils were used alone. The volatile oils were extracted by steam distillation using Clevenger hydrodistillator apparatus and each oil was tested for antimicrobial activity, while equal volume of these oils were blended and tested for antimicrobial activity....

Eco-Friendly Multipurpose Lubricating Greases from Vegetable Residual Oils

Directory of Open Access Journals (Sweden)

Ponnekanti Nagendramma

2015-10-01

Full Text Available Environmentally friendly multipurpose grease formulation has been synthesized by using Jatropha vegetable residual oil with lithium soap and multifunctional additive. The thus obtained formulation was evaluated for its tribological performance on a four-ball tribo-tester. The anti-friction and anti-wear performance characteristics were evaluated using standard test methods. The biodegradability and toxicity of the base oil was assessed. The results indicate that the synthesized residual oil grease formulation shows superior tribological performance when compared to the commercial grease. On the basis of physico-chemical characterization and tribological performance the vegetable residual oil was found to have good potential for use as biodegradable multipurpose lubricating grease. In addition, the base oils are biodegradable and non toxic.

Blends of nitrile butadiene rubber/poly (vinyl chloride: The use of maleated anhydride castor oil based plasticizer

Directory of Open Access Journals (Sweden)

Indiah Ratna Dewi

2016-06-01

Full Text Available Recently, much attention has been focused on research to replace petroleum-based plasticizers, with biodegradable materials, such as biopolymer which offers competitive mechanical properties. In this study, castor oil was modified with maleic anhydride (MAH to produce bioplasticizer named maleated anhydride castor oil (MACO, and used in nitrile butadiene rubber (NBR/poly vinyl chloride (PVC blend. The effect of MACO on its cure characteristics and mechanical properties of NBR/PVC blend has been determined. The reactions were carried out at different castor oil (CO/xylene ratios, i.e. 1:0 and 1:1 by weight, and fixed CO/MAH ratio, 1:3 by mole. DOP, CO, and MACO were added into each NBR/PVC blend according to the formula. It was found that the viscosity and safe process level of NBR/PVC blend is similar from all plasticizer, however, MACO (1:0 showed the highest cure rate index (CRI. MACO-based plasticizer gave a higher value of the mechanical properties of the NBR/PVC blend as compared to DOP based plasticizer. MACO (1:1 based plasticizer showed a rather significance performance compared to another type of plasticizers both before and after aging. The value of hardness, elongation at break, tensile strength, and tear strength were 96 Shore A, 155.91 %, 19.15 MPa, and 74.47 MPa, respectively. From this result, NBR/PVC blends based on MACO plasticizer can potentially replace the DOP, and therefore, making the rubber blends eco-friendly.

Investigation of Performance and Emissions Effects of Waste Vegetable Oil Methyl Ester in A Diesel Engine

Directory of Open Access Journals (Sweden)

Yahya ULUSOY

2016-12-01

Full Text Available In this study engine and emission performance of a 4-stroke, 4 cylinder, direct injection 62,5 kW engine, with three different biodiesel blends (B25, B50, B75,  was compared with those obtained with use of normal diesel (B0 through a 8-mode experimental test procedure, in convention with ISO 8178-C1. The results of the study showed that, performance and emission values of biodiesel fuels produced from vegetable oil and those obtained with diesel fuel (B0 are very close to each other.  In this context, the waste cooking oil, which is a serious risk to the environment and should be collected according to related legistlative measures,  could be processed to and used as biodiesel without creating any significant loss in terms of engine performance, while providing significant advantages in terms of engine emissions. These results revealed that, waste frying oils can be used as diesel fuel and to create an adding value for the economy instead of being potential environmental risk. 

Experimental investigations on mixing of two biodiesels blended with diesel as alternative fuel for diesel engines

Directory of Open Access Journals (Sweden)

K. Srithar

2017-01-01

Full Text Available The world faces the crises of energy demand, rising petroleum prices and depletion of fossil fuel resources. Biodiesel has obtained from vegetable oils that have been considered as a promising alternate fuel. The researches regarding blend of diesel and single biodiesel have been done already. Very few works have been done with the combination of two different biodiesel blends with diesel and left a lot of scope in this area. The present study brings out an experiment of two biodiesels from pongamia pinnata oil and mustard oil and they are blended with diesel at various mixing ratios. The effects of dual biodiesel works in engine and exhaust emissions were examined in a single cylinder, direct injection, air cooled and high speed diesel engine at various engine loads with constant engine speed of 3000 rpm. The influences of blends on CO, CO2, HC, NOx and smoke opacity were investigated by emission tests. The brake thermal efficiency of blend A was found higher than diesel. The emissions of smoke, hydro carbon and nitrogen oxides of dual biodiesel blends were higher than that of diesel. But the exhaust gas temperature for dual biodiesel blends was lower than diesel.

An experimental study of gaseous exhaust emissions of diesel engine using blend of natural fatty acid methyl ester

Science.gov (United States)

Sudrajad, Agung; Ali, Ismail; Samo, Khalid; Faturachman, Danny

2012-09-01

Vegetable oil form in Natural Fatty Acid Methyl Ester (FAME) has their own advantages: first of all they are available everywhere in the world. Secondly, they are renewable as the vegetables which produce oil seeds can be planted year after year. Thirdly, they are friendly with our environment, as they seldom contain sulphur element in them. This makes vegetable fuel studies become current among the various popular investigations. This study is attempt to optimization of using blend FAME on diesel engine by experimental laboratory. The investigation experimental project is comparison between using blend FAME and base diesel fuel. The engine experiment is conducted with YANMAR TF120M single cylinder four stroke diesel engine set-up at variable engine speed with constant load. The data have been taken at each point of engine speed during the stabilized engine-operating regime. Measurement of emissions parameters at difference engine speed conditions have generally indicated lower in emission NOx, but slightly higher on CO2 emission. The result also shown that the blends FAME are good in fuel consumption and potentially good substitute fuels for diesel engine

An experimental study of gaseous exhaust emissions of diesel engine using blend of natural fatty acid methyl ester

International Nuclear Information System (INIS)

Sudrajad, Agung; Ali, Ismail; Samo, Khalid; Faturachman, Danny

2012-01-01

Vegetable oil form in Natural Fatty Acid Methyl Ester (FAME) has their own advantages: first of all they are available everywhere in the world. Secondly, they are renewable as the vegetables which produce oil seeds can be planted year after year. Thirdly, they are friendly with our environment, as they seldom contain sulphur element in them. This makes vegetable fuel studies become current among the various popular investigations. This study is attempt to optimization of using blend FAME on diesel engine by experimental laboratory. The investigation experimental project is comparison between using blend FAME and base diesel fuel. The engine experiment is conducted with YANMAR TF120M single cylinder four stroke diesel engine set-up at variable engine speed with constant load. The data have been taken at each point of engine speed during the stabilized engine-operating regime. Measurement of emissions parameters at difference engine speed conditions have generally indicated lower in emission NO x , but slightly higher on CO 2 emission. The result also shown that the blends FAME are good in fuel consumption and potentially good substitute fuels for diesel engine

Optimization of Refining Craft for Vegetable Insulating Oil

Science.gov (United States)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

Vegetable oils as lube basestocks: A review

African Journals Online (AJOL)

anjanas

2013-02-27

Feb 27, 2013 ... widespread use of natural oils and fats. Vegetable oils are promising candidates as base ... Synthetic esters form a large group of products, which can be either from petrochemical or oleo chemical ... In order to combine the environmental behavior and the technical properties of lubricants, a lot of countries ...

Vegetable oils as diesel fuel

International Nuclear Information System (INIS)

Fedeli, E.; Girelli, A.

2001-01-01

During the seventies, one of the recurring fuels crisis gave rise to research on alternative sources and among them to the idea of utilizing vegetable oils. The research work made clear that the oils cannot be utilized as such but they must be transformed in simple esters, eliminating the problems arising from the presence of the glycerine. The Experiment Stations of the Industry, Commerce and Handicraft Department of the Italian Government, by request of the last one, in the '70/'80 has done a successful experimentation that is presented in the paper [it

Effect of Exhaust Gas Recirculation on Performance of a Diesel Engine Fueled with Waste Plastic Oil / Diesel Blends

Directory of Open Access Journals (Sweden)

Punitharani K.

2017-11-01

Full Text Available NOx emission is one of the major sources for health issues, acid rain and global warming. Diesel engine vehicles are the major sources for NOx emissions. Hence there is a need to reduce the emissions from the engines by identifying suitable techniques or by means of alternate fuels. The present investigation deals with the effect of Exhaust Gas Recirculation (EGR on 4S, single cylinder, DI diesel engine using plastic oil/Diesel blends P10 (10% plastic oil & 90% diesel in volume, P20 and P30 at various EGR rates. Plastic oil blends were able to operate in diesel engines without any modifications and the results showed that P20 blend had the least NOx emission quantity.

First Brazilian patent for dielectric vegetable oil for transformers; Primeira patente brasileira de oleo dieletrico vegetal para transformadores

Energy Technology Data Exchange (ETDEWEB)

Carioca, Jose O.B.; Carvalho, Paulo C.M.; Correa, Raimundo G.C.; Bernardo, Francisco A.B. [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil); Coelho Junior, Luiz G. [2 Companhia Energetica do Ceara (COELCE), Fortaleza, CE (Brazil); Abreu, Rosa F.A. [Universidade Estadual do Ceara (UECE), Fortaleza, CE (Brazil)

2008-07-01

The present paper discuss the development of different insulating oils for electric power transformers during the last hundred years and analyze comparatively the potential for the use of vegetable oils as a source for green dielectric oils, due to its high level of biodegradability, nontoxic, material compatibility, good electric strength and insulation properties, long-term oxidative and thermal stability, relatively low pour point and reasonable cost. Based on these premises, the authors developed a new type of insulating fluid based on Brazilian vegetable oils never used before for this purpose. This product is competitive with similar and patented products developed from canola and soya vegetable oils. Recently a new patent related with the process for the production of this fluid was submitted to the World Industrial Property Organization - WIPO. (author)

Highly efficient procedure for the transesterification of vegetable oil

Energy Technology Data Exchange (ETDEWEB)

Liang, Xuezheng; Gao, Shan; He, Mingyuan [Shanghai Key Laboratory of Green Chemistry and Chemical Process, Department of Chemistry, East China Normal University, Shanghai 200062 (China); Yang, Jianguo [Shanghai Key Laboratory of Green Chemistry and Chemical Process, Department of Chemistry, East China Normal University, Shanghai 200062 (China); Energy Institute, Department of Materials Science and Engineering, Pennsylvania State University, University Park, PA 16802 (United States)

2009-10-15

The highly efficient procedure has been developed for the synthesis of biodiesel from vegetable oil and methanol. The KF/MgO has been selected as the most efficient catalyst for the reactions with the yield of 99.3%. Operational simplicity, without need of the purification of raw vegetable oil, low cost of the catalyst used, high activities, no saponification and reusability are the key features of this methodology. (author)

Effect of vegetable oils on fatty acid composition and cholesterol content of chicken frankfurters

Science.gov (United States)

Belichovska, D.; Pejkovski, Z.; Belichovska, K.; Uzunoska, Z.; Silovska-Nikolova, A.

2017-09-01

To study the effect of pork adipose tissue substitution with vegetable oils in chicken frankfurters, six frankfurter formulations were produced: control; with pork backfat; with olive oil; with rapeseed oil; with sunflower oil; with palm oil, and; with a mixture of 12% rapeseed oil and 8% palm oil. Fatty acid composition and cholesterol content and some oxides thereof were determined in the final products. The use of vegetable oils resulted in improvement of the fatty acid composition and nutritional of frankfurters. Frankfurters with vegetable oils contained significantly less cholesterol and some of its oxides, compared to the frankfurters with pork fat. The formulation with palm oil had the least favourable fatty acid composition. The use of 12% rapeseed oil improved the ratio of fatty acids in frankfurters with a mixture of rapeseed and palm oils. Complete pork fat replacement with vegetable oils in chicken frankfurter production is technologically possible. The mixture of 12% rapeseed oil and 8% palm oil is a good alternative to pork fat from health aspects. Further research is needed to find the most appropriate mixture of vegetable oils, which will produce frankfurters with good sensory characteristics, a more desirable fatty acid ratio and high nutritional value.

Growth performance, carcass and meat quality of lambs supplemented with increasing levels of a tanniferous bush (Cistus ladanifer L.) and vegetable oils.

Science.gov (United States)

Francisco, A; Dentinho, M T; Alves, S P; Portugal, P V; Fernandes, F; Sengo, S; Jerónimo, E; Oliveira, M A; Costa, P; Sequeira, A; Bessa, R J B; Santos-Silva, J

2015-02-01

The effects of dietary inclusion of Cistus ladanifer L. (CL) and a vegetable oil blend were evaluated on growth performance,carcass and meat quality of fifty four lambs that were assigned to 9 diets, corresponding to 3 levels of CL(50, 100 and 200 g/kg DM) and 3 levels of oil inclusion (0, 40 and 80 g/kg DM). Treatments had no effects on growth rate. Oil depressed dry matter intake (P = 0.017), carcass muscle (P = 0.041) and increased (P = 0.016) kidney knob channel fat. Chemical and physical meat quality traits were not affected by treatments. Off-flavour perception was higher for 8% of oil (P b 0.001). The level of 100 g/kg DM of CL inclusion improved meat stability after 7 days of storage. Supplementation with linseed and soybean oils (2:1) was a good approach to improve meat nutritional value from feedlot lambs, increasing total n-3 PUFA.

Influence of biodiesel blending on physicochemical properties and importance of mathematical model for predicting the properties of biodiesel blend

International Nuclear Information System (INIS)

Wakil, M.A.; Kalam, M.A.; Masjuki, H.H.; Atabani, A.E.; Rizwanul Fattah, I.M.

2015-01-01

Highlights: • Short identification of selected biodiesel feedstock. • Review of physicochemical properties for blended biodiesel. • Mathematical model for predicting properties of various biodiesel blends. - Abstract: The growing demand for green world serves as one of the most significant challenges of modernization. Requirements like largest usage of energy for modern society as well as demand for friendly milieu create a deep concern in field of research. Biofuels are placed at the peak of the research arena for their underlying benefits as mentioned by multiple researches. Out of a number of vegetable oils, only a few are used commercially for biodiesel production. Due to various limitations of edible oil, non-edible oils are becoming a profitable choice. Till today, very little percentage of biodiesel is used successfully in engine. The research is still continuing for improving the biodiesel usage level. Recently, it is found that the blended biodiesel from more than one feedstock provides better performance in engine. This paper reviews the physicochemical properties of different biodiesel blends obtained from various feedstocks with a view to properly understand the fuel quality. Moreover, a short description of each feedstock is given along with graphical presentation of important properties for various blend percentages from B0 to B100. Finally, mathematical model is formed for predicting various properties of biodiesel blend with the help of different research data by using polynomial curve fitting method. The results obtained from a number of literature based on this work shows that the heating value of biodiesel is about 11% lower than diesel except coconut (14.5% lower) whereas kinematic viscosity is in the range of 4–5.4 mm 2 /s. Flash point of all biodiesels are more than 150 °C, except neem and coconut. Cold flow properties of calophyllum, palm, jatropha, moringa are inferior to others. This would help to determine important properties of

Property modification of jatropha oil biodiesel by blending with other biodiesels or adding antioxidants

International Nuclear Information System (INIS)

Chen, Yi-Hung; Chen, Jhih-Hong; Luo, Yu-Min; Shang, Neng-Chou; Chang, Cheng-Hsin; Chang, Ching-Yuan; Chiang, Pen-Chi; Shie, Je-Lueng

2011-01-01

The feasibility of biodiesel production from jatropha (Jatropha curcas) oil was investigated with respect to the biodiesel blending properties and its oxidation stability with antioxidants. The JME (jatropha oil methyl esters) had the cetane number of 54, cold filter plugging point of -2 o C, density of 881 kg/m 3 at 15 o C, ester content of 99.4 wt.%, iodine value of 96.55 g I 2 /100 g, kinematic viscosity of 4.33 mm 2 /s at 40 o C, and oxidation stability of 3.86 h. Furthermore, the JME was blended with palm oil biodiesel and soybean oil biodiesel at various weight ratios and evaluated for fuel properties as compared to the relevant specifications. In addition, several antioxidants at concentrations between 100 and 1000 ppm were studied for their potential to improve the oxidation stability of the JME. The relationship between the IP (induction period) in the measurement of the oxidation stability associated with the antioxidant consumption in the JME was described by first-order reaction rate kinetics. Moreover, the ln IP (natural logarithm of the IP) at various concentrations of pyrogallol showed a linear relationship with the test temperature. The oxidation stability at ambient temperatures was predicted on the basis of an extrapolation of the temperature-dependent relationship. -- Highlights: → Jatropha oil methyl esters had satisfactory biodiesel properties except for the oxidation stability. → The oxidation stability and cold filter plugging point of the jatropha-based biodiesel blends cannot meet the EN 14214 requirements simultaneously. → The addition of pyrogallol was recommended for the stabilization of the jatropha oil methyl esters with a concentration of 100-250 ppm.

Oilseeds and vegetable oils in asia: a world of diversity

Directory of Open Access Journals (Sweden)

Mittaine Jean-François

2016-11-01

Full Text Available Out of the two dozen countries that constitute what is generally called “Asia”, some are the largest in the world while others are islands with smaller populations. When looking at oilseeds and vegetable oils in the region, one is faced with the same huge diversity which makes it complex to analyze, all the more that statistics are not easily available for many countries. Aside from the large differences in size, the region covers a wide spectrum of diversified climate environments. Asia is also mainly characterized by its huge population which has become largely urban, a key factor leading to the impressive growth of vegetable oil demand in the past 30 years. At an verage of 23.2 kg/year, Asian per capita consumption of oils and fats still remains slightly below the world average of 28.3 kg/capita/year. Therefore, although 53% of the world population is located in Asia, only 45% of world oils and fats is consumed in the region. As detailed in the paper, the world of Asian oilseeds and vegetable oils is highly concentrated on soybeans and palm oil. In spite of a large domestic production in China (12.3 MnT, soybeans are imported in huge quantities, mostly by China (78 MnT, 84% of the region’s imports where more than 28% of world soybeans production is being crushed. Palm oil, the second large commodity consumed in the region, is mainly produced within the region, mostly in Indonesia and Malaysia. So where is the “world of diversity”? Hidden behind those two dominant commodities, practically all of the ten oilseeds constituting the core of the world production are grown in significant quantities in the region while, for vegetable oils, all those of significant importance are produced within the region with the exception of olive oil. The main question that should be kept in mind when reviewing this large regional demand is under what condition will future vegetable oil production be able to meet the expected rise of per capita oils and

THE EFFECT OF KARANJA OIL METHYL ESTER ON KIRLOSKAR HA394DI DIESEL ENGINE PERFORMANCE AND EXHAUST EMISSIONS

Directory of Open Access Journals (Sweden)

Sharanappa K Godiganur

2010-01-01

Full Text Available Biofuels are being investigated as potential substitutes for current high pollutant fuels obtained from the conventional sources. The primary problem associated with using straight vegetable oil as fuel in a compression ignition engine is caused by viscosity. The process of transesterifiction of vegetable oil with methyl alcohol provides a significant reduction in viscosity, thereby enhancing the physical properties of vegetable oil. The Kirloskar HA394 compression ignition, multi cylinder diesel engine does not require any modification to replace diesel by karanja methyl ester. Biodiesel can be used in its pure form or can be blended with diesel to form different blends. The purpose of this research was to evaluate the potential of karanja oil methyl ester and its blend with diesel from 20% to 80% by volume. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power of the mixture is closed to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that the blend of karanja ester and diesel fuel can be used as an alternative successfully in a diesel engine without any modification and in terms of emission parameters; it is an environmental friendly fuel

Butter blend containing fish oil improves the level of n-3 fatty acids in biological tissues of hamster

DEFF Research Database (Denmark)

Porsgaard, Trine; Overgaard, Jesper; Krogh, Anne Louise

2007-01-01

Many studies have shown beneficial effects of long chain n-3 polyunsaturated fatty acids (PUFA) on human health. Regardless of the positive effects of n-3 PUFA, the intake of these fatty acids remains low. An approach to increase the intake of n-3 PUFA in the population is to incorporate fish oil...... Syrian hamsters received hamster feed blended with one of the three butter products. After 6 weeks of feeding, the fatty acid compositions of plasma, erythrocytes, liver, brain, and visceral fat were determined. The intake of butter product with fish oil resulted in a higher level of n-3 PUFA in plasma...... into food. In the present study, fish oil was incorporated into butter blends by enzymatic interesterification. The aim of the study was to investigate the effects of this butter product in comparison with a commercial butter blend and a product produced by interesterification but without fish oil. Golden...

Antioxidant and chemical properties of essential oil extracted from blend of selected spices

Directory of Open Access Journals (Sweden)

Ochuko Lucky Erukainure

2015-07-01

Full Text Available Objective: To investigate the chemical properties of essential oil extracted from blends of selected Nigerian spices as well as its antioxidant protective potentials against free radical in vitro. Methods: Essential oil was extracted from selected spices blend consisting of Monodora myristica, Myristica fragrans, Tetrapleura tetraptera, and Aframomum sceptrum using a Clevenger type apparatus. Oil obtained was subjected to phytochemical and gas chromatography-mass spectrometer analysis as well as analyzed for antioxidant activity which covers for 1,1-diphenyl-2 picrylhydrazyl, nitric oxide scavenging activities and reducing property. Results: Gas chromatography-mass spectrometer analysis revealed over 50 compoundfs with α-phellandrene being the most predominant compound (27.32%, which was followed by (--β-bourbonene (15.78% and 5-(1-methylethyl-α-phellandrene (11.80%. Phytochemical analysis showed high flavonoid content and a lower phenolic content. The oil showed a dose like dependent effect on the1-diphenyl-2 picrylhydrazyl and nitric oxide scavenging activities, these activities increased with increasing concentration. The same was also observed for the reducing power properties of the oil. Conclusions: The antioxidant activities exhibited by the essential oil in vitro signify its protective potential against free radicals. The chemical constituents, α-phellandrene in particular and the studied phytochemicals may be responsible for these effects. However, in vivo study is needed to further authenticate this potency.

Prospects of application of vegetable oils as antifungal agents (Literature review

Directory of Open Access Journals (Sweden)

A. A. Mikheev

2017-04-01

Full Text Available Purpose of work – to summarize and present modern scientific literature reviews of alternative antifungal agents usage, among which herbal medicines, and in particular herbal oils, may play significant role. Fungal infections (mycoses are one of the leading infectious diseases in the world. Besides the medical importance, pathogenic fungi play a significant role in the food industry as potential pollutants. In order to treat fungal infections and to prevent food spoilage various medications that are products of chemical synthesis are widely used and the need for them increases significantly. However, among large number of medications and herbal drugs only a small part is used to treat fungal infections and to prevent food decay, though plants contain a lot of bioactive compounds with potential antifungal properties. Therefore, question of application of vegetable oils as antifungal agents is relevant. Various plants contain oils that have the potential antifungal properties, but are often used only in gastronomic purpose. The same time those oils can be successfully used for the treatment of candidiasis and infections caused by fungi of genera Aspergillus, Trichoderma, Penicillium, Fusarium, Metrhizium, Ophiostoma, Scopulariopsis and others. Their effects are manifested like using a single vegetable oil and mixtures of oils. Conclusions. Vegetable oils usage has big perspectives due to the lack of «addictive» effect and the development of resistance in fungi of different taxa. Vegetable oils do not require considerable investments for their reception, and thanks to traditions of aromo- and herbal medicine, their usage can be more effective in contrast to traditional chemotherapeutic agents. The search and study of new medicines based on vegetable oils may be a perspective direction of modern microbiological sciences and requires further deep studies of their biological properties and mechanisms of action.

Analysis of physical characteristics of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Piamba Tulcan, Oscar Edwin [Universidade Nacional da Colombia (UNAL), Bogota (Colombia). Fac. de Ingenieria; Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica], E-mail: oepiambat@unal.edu.co; Andrade, Danielle Oliveira de; Andrade, Ednilton Tavares de [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Agricola e do Meio Ambiente; Pereira, Roberto Guimaraes [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Mecanica

2008-07-01

Different vegetable oils were characterized using standardized methods. The evaluated characteristics were density, viscosity, flow point, cloud point and corrosion. The obtained data was tabulated and compared with average composition values of oils in percentage of fatty acids and iodine number for each oil. In this analysis it is shown that viscosity decreases with the increase of the iodine number, and density decrease. The cloud and flow point have greater relation with the presence of saturated or highly unsaturated fatty acids, respectively. The index of corrosion is greater when oil saturation or its iodine number are increased. (author)

Analysis of Brand Preference for Vegetable Oil in Abia State, Nigeria ...

African Journals Online (AJOL)

This study examined the consumer brand preference for vegetable oil in Abia State. It specifically focused on the determining factors that influenced consumer preference between branded and unbranded vegetable oil. This study adopted multistage sampling technique in the selection of a total sample of 150 respondents.

SOLID BIOFUEL UTILIZATION IN VEGETABLE OIL PRODUCTION

Directory of Open Access Journals (Sweden)

Slusarenko V.

2016-08-01

Full Text Available The paper deals with questions of creating at JSC “Alimentarmash "in the last 20 years the technological equipment for the production of vegetable oils from oilseeds: from the press for the final spin to mini oilfactory, using as an energy source for heating the liquid coolant (Thermal oil "Arian" of solid biofuels - husk of sunflower seeds.

Palm Oil Consumption Increases LDL Cholesterol Compared with Vegetable Oils Low in Saturated Fat in a Meta-Analysis of Clinical Trials.

Science.gov (United States)

Sun, Ye; Neelakantan, Nithya; Wu, Yi; Lote-Oke, Rashmi; Pan, An; van Dam, Rob M

2015-07-01

Palm oil contains a high amount of saturated fat compared with most other vegetable oils, but studies have reported inconsistent effects of palm oil on blood lipids. We systematically reviewed the effect of palm oil consumption on blood lipids compared with other cooking oils using data from clinical trials. We searched PubMed and the Cochrane Library for trials of at least 2 wk duration that compared the effects of palm oil consumption with any of the predefined comparison oils: vegetable oils low in saturated fat, trans fat-containing partially hydrogenated vegetable oils, and animal fats. Data were pooled by using random-effects meta-analysis. Palm oil significantly increased LDL cholesterol by 0.24 mmol/L (95% CI: 0.13, 0.35 mmol/L; I(2) = 83.2%) compared with vegetable oils low in saturated fat. This effect was observed in randomized trials (0.31 mmol/L; 95% CI: 0.20, 0.42 mmol/L) but not in nonrandomized trials (0.03 mmol/L; 95% CI: -0.15, 0.20 mmol/L; P-difference = 0.02). Among randomized trials, only modest heterogeneity in study results remained after considering the test oil dose and the comparison oil type (I(2) = 27.5%). Palm oil increased HDL cholesterol by 0.02 mmol/L (95% CI: 0.01, 0.04 mmol/L; I(2) = 49.8%) compared with vegetable oils low in saturated fat and by 0.09 mmol/L (95% CI: 0.06, 0.11 mmol/L; I(2) = 47.8%) compared with trans fat-containing oils. Palm oil consumption results in higher LDL cholesterol than do vegetable oils low in saturated fat and higher HDL cholesterol than do trans fat-containing oils in humans. The effects of palm oil on blood lipids are as expected on the basis of its high saturated fat content, which supports the reduction in palm oil use by replacement with vegetable oils low in saturated and trans fat. This systematic review was registered with the PROSPERO registry at http://www.crd.york.ac.uk/PROSPERO/display_record.asp?ID=CRD42012002601#.VU3wvSGeDRZ as CRD42012002601. © 2015 American Society for Nutrition.

Comparative evaluation of the effect of sweet orange oil-diesel blend on performance and emissions of a multi-cylinder compression ignition engine

Science.gov (United States)

Rahman, S. M. Ashrafur; Hossain, F. M.; Van, Thuy Chu; Dowell, Ashley; Islam, M. A.; Rainey, Thomas J.; Ristovski, Zoran D.; Brown, Richard J.

2017-06-01

In 2014, global demand for essential oils was 165 kt and it is expected to grow 8.5% per annum up to 2022. Every year Australia produces approximately 1.5k tonnes of essential oils such as tea tree, orange, lavender, eucalyptus oil, etc. Usually essential oils come from non-fatty areas of plants such as the bark, roots, heartwood, leaves and the aromatic portions (flowers, fruits) of the plant. For example, orange oil is derived from orange peel using various extraction methods. Having similar properties to diesel, essential oils have become promising alternate fuels for diesel engines. The present study explores the opportunity of using sweet orange oil in a compression ignition engine. Blends of sweet orange oil-diesel (10% sweet orange oil, 90% diesel) along with neat diesel fuel were used to operate a six-cylinder diesel engine (5.9 litres, common rail, Euro-III, compression ratio 17.3:1). Some key fuel properties such as: viscosity, density, heating value, and surface tension are presented. Engine performance (brake specific fuel consumption) and emission parameters (CO, NOX, and Particulate Matter) were measured to evaluate running with the blends. The engine was operated at 1500 rpm (maximum torque condition) with different loads. The results from the property analysis showed that sweet orange oil-diesel blend exhibits lower density, viscosity and surface tension and slightly higher calorific value compared to neat diesel fuel. Also, from the engine test, the sweet orange oil-diesel blend exhibited slightly higher brake specific fuel consumption, particulate mass and particulate number; however, the blend reduced the brake specific CO emission slightly and brake specific NOX emission significantly compared to that of neat diesel.

Castor oil biodiesel and its blends as alternative fuel

International Nuclear Information System (INIS)

Berman, Paula; Nizri, Shahar; Wiesman, Zeev

2011-01-01

Intensive production and commercialization of biodiesel from edible-grade sources have raised some critical environmental concerns. In order to mitigate these environmental consequences, alternative oilseeds are being investigated as biodiesel feedstocks. Castor (Ricinus communis L.) is one of the most promising non-edible oil crops, due to its high annual seed production and yield, and since it can be grown on marginal land and in semi-arid climate. Still, few studies are available regarding its fuel-related properties in its pure form or as a blend with petrodiesel, many of which are due to its extremely high content of ricinoleic acid. In this study, the specifications in ASTM D6751 and D7467 which are related to the fatty acid composition of pure castor methyl esters (B100) and its blend with petrodiesel in a 10% vol ratio (B10) were investigated. Kinematic viscosity and distillation temperature of B100 (15.17 mm 2 s -1 and 398.7 o C respectively) were the only two properties which did not meet the appropriate standard limits. In contrast, B10 met all the specifications. Still, ASTM D7467 requires that the pure biodiesel meets the requirements of ASTM D6751. This can limit the use of a wide range of feedstocks, including castor, as alternative fuel, especially due to the fact that in practice vehicles normally use low level blends of biodiesel and petrodiesel. These issues are discussed in depth in the present study. -- Highlights: → CaME can be used as a biodiesel alternative feedstock when blended in petrodiesel. → Due to the high levels of ricinoleic acid maximum blending level is limited to 10%. → Today, CaME blends are not a viable alternative feedstock. → ASTM D7467 requires that pure biodiesel must meet all the appropriate limits.

Crystallization of low saturated lipid blends of palm and canola oils with sorbitan monostearate and fully hydrogenated palm oil.

Science.gov (United States)

Barbosa, Karina Martins; Cardoso, Lisandro Pavie; Ribeiro, Ana Paula Badan; Kieckbusch, Theo Guenter; Buscato, Monise Helen Masuchi

2018-03-01

Several scientific investigations have focused on providing new strategies for supporting the development of low saturated and zero trans lipid materials, as healthier fat alternatives for food application. This work evaluated the consistency, crystallization behavior, microstructure and polymorphism of six blends composed of palm and canola oils at different concentrations (100:0, 80:20, 60:40, 40:60, 20:80 and 0:100, in w/w%) added with 5.0% of fully hydrogenated palm oil (FHPO) or with a mixture of 2.5% of FHPO and 2.5% of sorbitan monostearate (SMS). The results were compared with the non-structured blends (standard samples). Through microstructure images, the formation of a more homogeneous and denser packed crystal network was observed for samples added with both crystallization modifiers (FHPO/SMS) compared to the corresponding standard samples, after stabilization at 25 °C during 3 h. In particular, enhanced crystallization modifications were observed for the 40:60 blend, in which the crystal form β' emerged after the addition of FHPO/SMS. Moreover, the 40:60 blend structured with FHPO/SMS showed increased consistency (from 30 to 658 g F /cm 2 ) and induced onset crystallization in a higher temperature (from 13.1 to 23.9 °C) compared with the non-structured one, due to the specific crystallization effects provided by both added structurants.

Development of a method for the characterization of the oxidation stability of domestic heating oil and domestic heating oil with alternative components using chemiluminescence; Entwicklung einer Analysemethode zur Charakterisierung der Oxidationsstabilitaet von Heizoel EL und Heizoel EL A mittels Chemilumineszenz

Energy Technology Data Exchange (ETDEWEB)

Koch, Winfried; Lukito, Jayadi; Schloss, Heide vom [Oel-Waerme-Institut gGmbH (OWI), Aachen-Herzogenrath (Germany)

2013-04-15

The project's aim was to develop a process that serves to determine the oxidation stability of heating oil - FAME-/ heating oil - vegetable oil-blends clearly. Due to a directed energy input by means of the process of chemiluminescence, statements about the storage stability and the thermal stability of blends can be made. During the process the ageing of blend components and of the heating oil are taken into consideration. As a result, ageing processes and products of pure heating oil as well as biogenic components can be determined. It was shown that the process is applicable to blends up to an admixture of at least 20 % (V/V) of biogenic components, whereby blends with higher admixture shares can be analyzed as well. According to DIN SPEC 51603 - 6 'Heating Oil Alternative' the admixture of FAME is limited to 20 %(V/V) and the admixture of vegetable oil to 5 % (V/V) because of the distillation range. On the basis of these investigations it could be shown how oxidation products influence the signal process of the chemiluminescence radiation and how they can be correlated by a measurable physical value. Moreover, a new evaluation criterion has been developed. By means of this criterion a good reproducibility - regarding the determination of the oxidation stability according to the chemiluminescence methodology for non-aged fuels - can be achieved. The fuel characteristic decrease in the stability of the tested fuels can be represented only partially by the chemiluminescence process, as the measured values are subject to fluctuations. (orig.)

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

NARCIS (Netherlands)

Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

2017-01-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

Impact of residual glycerides on viscosity of biodiesel (waste and rapeseed oil blends)

OpenAIRE

Z. Jurac; L. Pomenić

2013-01-01

Purpose: Biodiesel, mixture of fatty acid methyl esters is a biodegradable alternative fuel that is obtained from renewable sources as a vegetable oils or animal fats. Use of waste cooking oils reduce the cost of raw materials for biodiesel production and also reduces the environment pollution. Moreover, pure edible vegetable oils for biodiesel production have an ethical significance because food is used to produce fuel. The aim of this work is a presentation of effects that r...

Effect of surfactant and surfactant blends on pseudoternary phase diagram behavior of newly synthesized palm kernel oil esters

Directory of Open Access Journals (Sweden)

Mahdi ES

2011-06-01

Full Text Available Elrashid Saleh Mahdi1, Mohamed HF Sakeena1, Muthanna F Abdulkarim1, Ghassan Z Abdullah1,3, Munavvar Abdul Sattar2, Azmin Mohd Noor11Department of Pharmaceutical Technology, 2Department of Physiology, School of Pharmaceutical Sciences, Universiti Sains Malaysia, Minden, Penang, Malaysia; 3Department of Pharmaceutical Technology, International Medical University, Bukit Jalil, Kuala Lumpur, MalaysiaBackground: The purpose of this study was to select appropriate surfactants or blends of surfactants to study the ternary phase diagram behavior of newly introduced palm kernel oil esters.Methods: Nonionic surfactant blends of Tween® and Tween®/Span® series were screened based on their solubilization capacity with water for palm kernel oil esters. Tween® 80 and five blends of Tween® 80/Span® 80 and Tween® 80/Span® 85 in the hydrophilic-lipophilic balance (HLB value range of 10.7–14.0 were selected to study the phase diagram behavior of palm kernel oil esters using the water titration method at room temperature.Results: High solubilization capacity was obtained by Tween® 80 compared with other surfactants of Tween® series. High HLB blends of Tween® 80/Span® 85 and Tween® 80/Span® 80 at HLB 13.7 and 13.9, respectively, have better solubilization capacity compared with the lower HLB values of Tween® 80/Span® 80. All the selected blends of surfactants were formed as water-in-oil microemulsions, and other dispersion systems varied in size and geometrical layout in the triangles. The high solubilization capacity and larger areas of the water-in-oil microemulsion systems were due to the structural similarity between the lipophilic tail of Tween® 80 and the oleyl group of the palm kernel oil esters.Conclusion: This study suggests that the phase diagram behavior of palm kernel oil esters, water, and nonionic surfactants is not only affected by the HLB value, but also by the structural similarity between palm kernel oil esters and the surfactant

Study on Combustion Performance of Diesel Engine Fueled by Synthesized Waste Cooking Oil Biodiesel Blends

Directory of Open Access Journals (Sweden)

Duraid F. Maki

2018-02-01

Full Text Available The waste cooking oil or used cooking oil is the best source of biodiesel synthesizing because it enters into the so-called W2E field whereas not only get rid of the used cooking oils but produce energy from waste fuel. In this study, biodiesel was synthesized from the used cooking oil and specifications are tested. From 1 liter of used cooking oil, 940 ml is gained. The remaining of liter is glycerin and water. Blend of 20% of biodiesel with 80% of net diesel by volume is formed. Blends of 100% diesel and 100% biodiesel are prepared too. The diesel engine combustion performance is studied. Brake thermal efficiency, brake specific fuel consumption, volumetric efficiency, mean effective pressure, and engine outlet temperature. Cylinder pressure variation with crank angle is analyzed. At last not least, the concentrations of hydro carbon and nitrogen pollutants are measured. The results showed significant enhancement in engine power and pollutant gases emitted. There is positive compatible with other critical researches.

Properties of chicken manure pyrolysis bio-oil blended with diesel and its combustion characteristics in RCEM, Rapid Compression and Expansion Machine

Directory of Open Access Journals (Sweden)

Sunbong Lee

2014-06-01

Full Text Available Bio-oil (bio-oil was produced from chicken manure in a pilot-scale pyrolysis facility. The raw bio-oil had a very high viscosity and sediments which made direct application to diesel engines difficult. The bio-oil was blended with diesel fuel with 25% and 75% volumetric ratio at the normal temperature, named as blend 25. A rapid compression and expansion machine was used for a combustion test under the experimental condition corresponding to the medium operation point of a light duty diesel engine using diesel fuel, and blend 25 for comparison. The injection related pressure signal and cylinder pressure signal were instantaneously picked up to analyze the combustion characteristics in addition to the measurement of NOx and smoke emissions. Blend 25 resulted in reduction of the smoke emission by 80% and improvements of the apparent combustion efficiency while the NOx emission increased by 40%. A discussion was done based on the analysis results of combustion.

Vegetable fats and oils as functional ingredients in meat products

Directory of Open Access Journals (Sweden)

Alfonso Totosaus

2011-12-01

Full Text Available Sausages are a widely consumed food in México, and due to their low fat content (ca. 10% they can be employed to enrich diet by including functional or nutraceutic ingredients as vegetable fats and oils. The replace or incorporation of vegetable fats or oils in cooked sausages is a way to improve their nutritional profile to offer functional meat products.

Phase transitions, solubility, and crystallization kinetics of phytosterols and phytosterol-oil blends.

Science.gov (United States)

Vaikousi, Hariklia; Lazaridou, Athina; Biliaderis, Costas G; Zawistowski, Jerzy

2007-03-07

The thermal properties, solubility characteristics, and crystallization kinetics of four commercial phytosterol preparations (soy and wood sterols and stanols) and their blends with corn oil were examined. Differential scanning calorimetry (DSC) revealed narrow melting peaks between 138 and 145 degrees C for all phytosterol samples, reversible on rescan. Broader and less symmetrical melting transitions at lower temperatures with increasing oil content were observed for two samples of phytosterol-oil admixtures. The estimated, from the solubility law, deltaH values (34.7 and 70.7 mJ/mg for wood sterols and stanols, respectively), were similar to the DSC experimental data. Fatty acid esters of soy stanols differing in the chain length of the acyl groups (C2-C12) exhibited suppression of the melting point and increase of the fusion enthalpy with increasing chain length of the acyl group; the propionate ester exhibited the highest melting point (Tm: 151 degrees C) among all stanol-fatty acid esters. Solubility of phytosterols in corn oil was low (2-3% w/w at 25 degrees C) and increased slightly with a temperature rise. Plant sterols appeared more soluble than stanols with higher critical concentrations at saturation. The induction time for recrystallization of sterol-oil liquid blends, as determined by spectrophotometry, depended on the supersaturation ratio. The calculated interfacial free energies between crystalline sediments and oil were smaller for sterol samples (3.80 and 3.85 mJ/m2) than stanol mixtures (5.95 and 6.07 mJ/m2), in accord with the higher solubility of the sterol crystals in corn oil. The XRD patterns and light microscopy revealed some differences in the characteristics among the native and recrystallized in oil phytosterol preparations.

Thermal stability of biodiesel and its blends: A review

Energy Technology Data Exchange (ETDEWEB)

Jain, Siddharth; Sharma, M.P. [Biofuel Research Laboratory, Alternate Hydro Energy Centre, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

2011-01-15

The vegetable oil, fats and their biodiesel suffer with the drawback of deterioration of its quality during long term storage unlike petroleum diesel due to large number of environmental and other factors making the fuel stability and quality questionable. There are various types of stabilities like oxidation, storage and thermal, playing key roles in making the fuel unstable. The present paper is an attempt to review the work done so far on the thermal stability of biodiesel and their blends with diesel under different conditions. The mechanism of thermal deterioration of vegetable oils, various methods of stability measurement including a new proposed method based on Karl Fischer coulometer, an alternative to conventional Rancimat test has been discussed. No correlations have been found in the literature among the results of various methods used. The effect of antioxidants on the stability parameters has also been discussed. TGA/DTA has been found as an effective method to check the deterioration of oil with respect to temperature using activation energy and order of reaction as the parameter to monitor the deterioration of oil. (author)

Castor oil biodiesel as an alternative fuel for diesel engines

International Nuclear Information System (INIS)

Benavides, Alirio; Benjumea, Pedro; Pashova, Veselina

2007-01-01

In this paper, a study related to the production and use of castor oil biodiesel is presented. The maximum methyl esters yield of the castor oil transesterification reaction is obtained under the following conditions: ambient temperature, a molar ratio of methanol to vegetable oil equal to 9 and a catalyst percentage equal to 0.8%. The castor oil biodiesel can be blended with petroleum diesel as far as 15% in such way that the resulting blend complies with national and international technical standards for diesel fuels. Its high viscosity becomes the main difficulty for using castor oil biodiesel in engines. However this biofuel exhibits excellent cold flow properties (low values of cloud and pour points). The motor tests using castor oil biodiesel petroleum diesel blends, for the biodiesel proportion tested; show that a biodiesel percentage increase leads to an increase in the specific fuel consumption, a decrease in the fuel air ratio, a slight decrease in smoke opacity, while the fuel conversion efficiency and the CO and CO 2 emissions practically remain constants

Prediction of the viscosity of lubricating oil blends at any temperature

Energy Technology Data Exchange (ETDEWEB)

Diaz, R.M.; Bernardo, M.I.; Fernandez, A.M.; Folgueras, M.B. [University of Oviedo, Oveido (Spain). Dept. of Energy

1996-04-01

This paper discusses a method of predicting the viscosity of multicomponent base lubricating oil mixtures based on Andrade`s equation. The kinematic viscosity of three types of base lubricating oils and their binary and ternary mixtures were measured at different temperatures and the parameters of Andrade`s equation were calculated. The results obtained indicate that the Andrade parameters vary linearly with the mixture composition. From these linear equations, generalized mixing equations are derived which confirm the experimental results. By application of the mixing equations, a simple method is obtained for prediction of the viscosity of oil blends at any temperature from viscosity-temperature data of the oil components. The calculated viscosities gave an average absolute deviation of 10% over the temperature range 20-100{degree}C. 8 refs., 3 figs., 4 tabs.

Optimization of biodiesel production process using recycled vegetable oil

Science.gov (United States)

Lugo, Yarely

Petro diesel toxic emissions and its limited resources have created an interest for the development of new energy resources, such as biodiesel. Biodiesel is traditionally produced by a transesterification reaction between vegetable oil and an alcohol in the presence of a catalyst. However, this process is slow and expensive due to the high cost of raw materials. Low costs feedstock oils such as recycled and animal fats are available but they cannot be transesterified with alkaline catalysts due to high content of free fatty acids, which can lead to undesirable reactions such as saponification. In this study, we reduce free fatty acids content by using an acid pre-treatment. We compare sulfuric acid, hydrochloric acid and ptoluenesulfonic acid (PTSA) to pre-treat recycled vegetable oil. PTSA removes water after 60 minutes of treatment at room temperature or within 15 minutes at 50°C. The pretreatment was followed by a transesterification reaction using alkaline catalyst. To minimize costs and accelerate reaction, the pretreatment and transesterification reaction of recycle vegetable oil was conducted at atmospheric pressure in a microwave oven. Biodiesel was characterized using a GC-MS method.

The effects of heated vegetable oils on blood pressure in rats

Directory of Open Access Journals (Sweden)

Kamsiah Jaarin

2011-01-01

Full Text Available OBJECTIVES: The goal of this study was to determine the possible mechanism that is involved in the blood pressureraising effect of heated vegetable oils. METHODS: Adult male Sprague-Dawley rats were divided into 11 groups; the control group was fed with rat chow, and the other groups were fed with chow that was mixed with 15% weight/weight palm or soy oils, which were either in a fresh form or heated once, twice, five, or ten times. Blood pressures were measured at the baseline and throughout the 24-week study. Plasma nitric oxide levels were assessed prior to treatment and at the end of the study. Following 24 weeks, the rats were sacrificed to investigate their vascular reactivity using the thoracic aorta. RESULTS: Palm and soy oils had no detrimental effects on blood pressure, and they significantly elevated the nitric oxide contents and reduced the contractile responses to phenylephrine. However, trials using palm and soy oils that were repeatedly heated showed an increase in blood pressure, enhanced phenylephrine-induced contractions, reduced acetylcholine- and sodium nitroprusside-induced relaxations relative to the control and rats that were fed fresh vegetable oils. CONCLUSIONS: The blood pressure-raising effect of the heated vegetable cooking oils is associated with increased vascular reactivity and a reduction in nitric oxide levels. The chronic consumption of heated vegetable oils leads to disturbances in endogenous vascular regulatory substances, such as nitric oxide. The thermal oxidation of the cooking oils promotes the generation of free radicals and may play an important contributory role in the pathogenesis of hypertension in rats.

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Directory of Open Access Journals (Sweden)

Li Benkai

2016-08-01

Full Text Available Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL. This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that (1 castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient; (2 palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient; (3 MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil; (4 viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils; (5 although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature; (6 saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and (7 a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy

Vegetable Oils Consumption as One of the Leading Cause of Cancer and Heart Disease

OpenAIRE

Somayeh Zaminpira; Sorush Niknamian

2017-01-01

This review takes a deep look at increases in the incidence of cancer and heart disease after the introduction of industrial vegetable oils in the world. Most vegetable oils are highly processed and refined products, which completely lack the essential nutrients. Omega-6 Linoleic acid from vegetable oils increases oxidative stress in the body of humans, contributing to endothelial dysfunction and heart disease. The consumption of these harmful oils which are high in mega-6 polyunsaturated fat...

Application of Canola Oil Biodiesel/Diesel Blends in a Common Rail Diesel Engine

Directory of Open Access Journals (Sweden)

Jun Cong Ge

2016-12-01

Full Text Available In this study, the application effects of canola oil biodiesel/diesel blends in a common rail diesel engine was experimentally investigated. The test fuels were denoted as ULSD (ultra low sulfur diesel, BD20 (20% canola oil blended with 80% ULSD by volume, and PCO (pure canola oil, respectively. These three fuels were tested under an engine speed of 1500 rpm with various brake mean effective pressures (BMEPs. The results indicated that PCO can be used well in the diesel engine without engine modification, and that BD20 can be used as a good alternative fuel to reduce the exhaust pollution. In addition, at low engine loads (0.13 MPa and 0.26 MPa, the combustion pressure of PCO is the smallest, compared with BD20 and ULSD, because the lower calorific value of PCO is lower than that of ULSD. However, at high engine loads (0.39 MPa and 0.52 MPa, the rate of heat release (ROHR of BD20 is the highest because the canola oil biodiesel is an oxygenated fuel that promotes combustion, shortening the ignition delay period. For exhaust emissions, by using canola oil biodiesel, the particulate matter (PM and carbon monoxide (CO emissions were considerably reduced with increased BMEP. The nitrogen oxide (NOx emissions increased only slightly due to the inherent presence of oxygen in biodiesel.

Effects of dietary fish oil replacement by vegetable oil on the digestive enzymes activity and intestinal morphology in Meagre, Argyrosomus regius (Asso, 1801

Directory of Open Access Journals (Sweden)

Fernando Antunes Magalhães

2014-07-01

The results were analyzed by three way factorial. Amylase activity was bigger in FO when compared with VO (Table 1. The same result was observed in chymotrypsin activity. On the other hand, lipase activity was higher in VO. Regarding the levels of lipids, diets with 17% had higher amylase activity than diets with 12%. The inverse was observed in chymotrypsin activity. In relation to lipase activity, no differences were observed on the two levels of lipids studied. No differences in digestive enzymes activities were observed when diets were supplemented with selenium. Epithelium architecture of the posterior intestine was slightly affected by dietary treatments. Higher levels of lipids seem to induce enterocyte vacuolization, and vacuoles seem to be larger when a blend of vegetable oils was used instead of fish oil. No clear role can be attributed to selenium regarding intestinal morphology. In conclusion, our study showed that the source and levels of lipid in diets for meagre have influence in activity of digestible enzymes like amylase, lipase and chymotrypsin. Furthermore, levels of selenium do not cause an alteration in studied digestible enzymes.

Potential for using a tyre pyrolysis oil-biodiesel blend in a diesel engine at different compression ratios

International Nuclear Information System (INIS)

Sharma, Abhishek; Murugan, S.

2015-01-01

Highlights: • The possibility of operating a compression ignition engine with a non petroleum diesel fuel. • A possible solution to replace certain amount of biodiesel by tyre pyrolysis oil in a biodiesel fueled diesel engine. • The optimum compression ratio for engine fueled with biodiesel-tyre pyrolysis oil blend. - Abstract: This study is aimed at investigating effects of varying the compression ratio at optimum injection timing and nozzle opening pressure on the behaviour of a diesel engine, using a non-petroleum fuel, i.e. a blend of 80% biodiesel, and 20% oil obtained from pyrolysis of waste tyres. The engine was subjected to one lower (16.5) and one higher (18.5) compression ratio in addition to the standard compression ratio of 17.5. At the higher compression ratio of 18.5 and full load, shorter ignition delay, maximum cylinder pressure and higher heat release rate were found for the blend, compared to those of the original compression ratio. The increase in the compression ratio from 17.5 to 18.5 for the blend improved the brake thermal efficiency by about 8% compared to that of the original compression ratio at full load. The experimental results indicated that for the blend at a higher compression ratio of 18.5, the brake specific carbon monoxide (BSCO), brake specific hydrocarbon emission (BSHC) and smoke opacity were reduced by about 10.5%, 32%, and 17.4% respectively, than those of the original compression ratio at full load

Determination of SFC, FFA, and equivalent reaction time for enzymatically interestified oils using NIRS

DEFF Research Database (Denmark)

Houmøller, Lars P.; Kristensen, Dorthe; Rosager, Helle

2007-01-01

The use of near infrared spectroscopy (NIRS) for rapid determination of the degree of interesterification of blends of palm stearin, coconut oil, and rapeseed oil obtained using an immobilized Thermomyces lanuginosa lipase at 70 ◦C was investigated. Interesterification was carried out by applying...... that NIRS could be used to replace the traditional methods for determining FFA and SFC in vegetable oils.It was possible to monitor the activity of the immobilized enzyme for interesterification of margarine oils by predicting the equivalent reaction time in a batch reactor from NIR spectra. Root mean...... square errors of prediction for two different oil blends interesterified for 300 and 170 min were 21 and 12 min, respectively....

Controlling the frying stability of vegetable oils with tocopherols and phytosterols

Science.gov (United States)

Polyunsaturated vegetable oils are usually oxidatively stable for salad oils; however, in high stability applications such as frying, these oils are not resistant to the deteriorative processes of oxidation, hydrolysis and polymerization. To solve this problem in the past, oils were hydrogenated an...

Performance and emission characteristics of a DI compression ignition engine operated on Honge, Jatropha and sesame oil methyl esters

Energy Technology Data Exchange (ETDEWEB)

Banapurmath, N.R.; Tewari, P.G. [Department of Mechanical Engineering, B.V.B. College of Engineering and Technology, Vidyanagar, Poona-Bangalore Road, Hubli 580031 (India); Hosmath, R.S. [Department of Mechanical Engineering, K.L.E' s C.E.T., Belgaum (India)

2008-09-15

The high viscosity of vegetable oils leads to problem in pumping and spray characteristics. The inefficient mixing of vegetable oils with air contributes to incomplete combustion. The best way to use vegetable oils as fuel in compression ignition (CI) engines is to convert it into biodiesel. Biodiesel is a methyl or ethyl ester of fatty acids made from vegetable oils (both edible and non-edible) and animal fat. The main resources for biodiesel production can be non-edible oils obtained from plant species such as Pongamia pinnata (Honge oil), Jatropha curcas (Ratanjyot), Hevea brasiliensis (Rubber) and Calophyllum inophyllum (Nagchampa). Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. This paper presents the results of investigations carried out on a single-cylinder, four-stroke, direct-injection, CI engine operated with methyl esters of Honge oil, Jatropha oil and sesame oil. Comparative measures of brake thermal efficiency, smoke opacity, HC, CO, NO{sub X}, ignition delay, combustion duration and heat release rates have been presented and discussed. Engine performance in terms of higher brake thermal efficiency and lower emissions (HC, CO, NO{sub X}) with sesame oil methyl ester operation was observed compared to methyl esters of Honge and Jatropha oil operation. (author)

Detection of Adulterated Vegetable Oils Containing Waste Cooking Oils Based on the Contents and Ratios of Cholesterol, β-Sitosterol, and Campesterol by Gas Chromatography/Mass Spectrometry.

Science.gov (United States)

Zhao, Haixiang; Wang, Yongli; Xu, Xiuli; Ren, Heling; Li, Li; Xiang, Li; Zhong, Weike

2015-01-01

A simple and accurate authentication method for the detection of adulterated vegetable oils that contain waste cooking oil (WCO) was developed. This method is based on the determination of cholesterol, β-sitosterol, and campesterol in vegetable oils and WCO by GC/MS without any derivatization. A total of 148 samples involving 12 types of vegetable oil and WCO were analyzed. According to the results, the contents and ratios of cholesterol, β-sitosterol, and campesterol were found to be criteria for detecting vegetable oils adulterated with WCO. This method could accurately detect adulterated vegetable oils containing 5% refined WCO. The developed method has been successfully applied to multilaboratory analysis of 81 oil samples. Seventy-five samples were analyzed correctly, and only six adulterated samples could not be detected. This method could not yet be used for detection of vegetable oils adulterated with WCO that are used for frying non-animal foods. It provides a quick method for detecting adulterated edible vegetable oils containing WCO.

Enzymatic transesterification of waste vegetable oil to produce biodiesel.

Science.gov (United States)

Lopresto, C G; Naccarato, S; Albo, L; De Paola, M G; Chakraborty, S; Curcio, S; Calabrò, V

2015-11-01

An experimental study on enzymatic transesterification was performed to produce biodiesel from waste vegetable oils. Lipase from Pseudomonas cepacia was covalently immobilized on a epoxy-acrylic resin support. The immobilized enzyme exhibited high catalytic specific surface and allowed an easy recovery, regeneration and reutilisation of biocatalyst. Waste vegetable oils - such as frying oils, considered not competitive with food applications and wastes to be treated - were used as a source of glycerides. Ethanol was used as a short chain alcohol and was added in three steps with the aim to reduce its inhibitory effect on lipase activity. The effect of biocatalyst/substrate feed mass ratios and the waste oil quality have been investigated in order to estimate the process performances. Biocatalyst recovery and reuse have been also studied with the aim to verify the stability of the biocatalyst for its application in industrial scale. Copyright © 2015 Elsevier Inc. All rights reserved.

Review of Heterogeneous Catalysts for Catalytically Upgrading Vegetable Oils into Hydrocarbon Biofuels

OpenAIRE

Xianhui Zhao; Lin Wei; Shouyun Cheng; James Julson

2017-01-01

To address the issues of greenhouse gas emissions associated with fossil fuels, vegetable oilseeds, especially non-food oilseeds, are used as an alternative fuel resource. Vegetable oil derived from these oilseeds can be upgraded into hydrocarbon biofuel. Catalytic cracking and hydroprocessing are two of the most promising pathways for converting vegetable oil to hydrocarbon biofuel. Heterogeneous catalysts play a critical role in those processes. The present review summarizes current progres...

Emission of particulate matter from ternary blends consisting of biodiesel, ethanol and vegetable oil: a comparison with conventional dieselEmissão de material particulado por misturas ternárias compostas de biodiesel, etanol e óleo vegetal: uma comparação com o óleo diesel convencional

Directory of Open Access Journals (Sweden)

Murilo Daniel de Melo Innocentini

2011-12-01

Full Text Available The purpose of this study was to quantify the particulate matter emission from ternary blends comprehending biodiesel, ethanol and vegetable oil in a Diesel cycle engine, and an identical engine working with petrol diesel as control. To compare the fuels’ emissions, the particulate matter from the engine’s exhaust was collected, using a fiberglass circular filter paper, which was coupled by means of a steel flange at the end of the exhaust pipe. The results with ternary blends showed expressive reduction of particulate matter level exhausted by the engine, in its maximum load. We can conclude that the utilization of ternary blends, with the methods and conditions of this experiment, was efficient to reduce the emission of particulate matter contained in the exhaust gases of Diesel cycle engine.O objetivo deste trabalho foi quantificar a emissão de material particulado de misturas ternárias compostas de biodiesel, etanol e óleo vegetal em um motor de ciclo Diesel, tendo como testemunha um motor idêntico funcionando com óleo diesel de petróleo. Para a comparação da emissão dos dois combustíveis, foi realizada a coleta de material particulado proveniente dos escapamentos dos motores com um filtro circular confeccionado de fibra de vidro, que foi acoplado com um flange de aço, no final da tubulação de escape. Os resultados obtidos com a utilização das misturas ternárias de biocombustíveis indicaram uma redução expressiva no nível de material particulado emitido pelo motor em sua carga máxima. Pode-se concluir que a utilização das misturas ternárias, nas condições e métodos de realização do experimento, foi eficiente na redução de emissão de material particulado presente nos gases de exaustão do motor de ciclo Diesel.

The effect of refining step on the changes in viscosity values of vegetable oils

International Nuclear Information System (INIS)

Ergonul, P.G.

2013-01-01

In this work, the viscosity values of chemically refined vegetable oils (sunflower, corn, soybean and rapeseed) and physically refined vegetable oils (olive and palm) were determined during refining processes. At this point of view, fatty acid compositions and viscosity values of oil samples were determined. The edible vegetable oils presented Newtonian behavior in shear rates at ranges 6.28-20.93 s/sup -1/. It was observed that palm oil is more viscous than the others. During physical refining, the effect of both oil type and refining steps were significantly important, whereas in chemical refining only the effect of oil type was found statistically important (p<0.01). It was observed that correlation among fatty acid compositions and viscosity values of the samples showed differences according to oil type. (author)

The dynamic model on the impact of biodiesel blend mandate (B5) on Malaysian palm oil domestic demand: A preliminary finding

Science.gov (United States)

Abidin, Norhaslinda Zainal; Applanaidu, Shri-Dewi; Sapiri, Hasimah

2014-12-01

Over the last ten years, world biofuels production has increased dramatically. The biodiesel demand is driven by the increases in fossil fuel prices, government policy mandates, income from gross domestic product and population growth. In the European Union, biofuel consumption is mostly driven by blending mandates in both France and Germany. In the case of Malaysia, biodiesel has started to be exported since 2006. The B5 of 5% blend of palm oil based biodiesel into diesel in all government vehicles was implemented in February 2009 and it is expected to be implemented nationwide in the nearest time. How will the blend mandate will project growth in the domestic demand of palm oil in Malaysia? To analyze this issue, a system dynamics model was constructed to evaluate the impact of blend mandate implementation on the palm oil domestic demand influence. The base run of simulation analysis indicates that the trend of domestic demand will increase until 2030 in parallel with the implementation of 5 percent of biodiesel mandate. Finally, this study depicts that system dynamics is a useful tool to gain insight and to experiment with the impact of changes in blend mandate implementation on the future growth of Malaysian palm oil domestic demand sector.

Physicochemical studies on sunflower oil blended with cold pressed tiger nut oil during deep frying process

Directory of Open Access Journals (Sweden)

Ali Rehab, F. M.

2012-10-01

Full Text Available Sunflower oils were blended with different levels of cold pressed tiger nut oil. Blended oils were obtained by mixing tiger nut oil with sunflower oil at the volume ratios of 0:100, 10: 90, 20: 80, 30: 70, 40: 60, 50:50 and 100: 0. The effects of deep frying on physico-chemical parameters (Free Fatty Acid (FFA, Peroxide Value (PV, thiobarbituric acid value (TBA, iodine value, Total Polar Compounds (TPC, color and viscosity were evaluated over 30 hours of the frying process. The total phenolic content of native oils was determined. GLC analysis was performed to illustrate the fatty acid composition of sunflower oil, tiger nut oil and binary mixtures of them as well as their oxidation rates. The pure and blended oils were heated at 180 °C ± 5 °C, then frozen French fried potatoes were fried every 30 min. Oil samples were taken every 5 h and the entire continuous frying period was 30 h. The results showed that fresh sunflower oil had significantly the highest value of COX (7.25; while tiger nut oil had significantly the lowest (2.24. Mixing sunflower oil with different levels of tiger nut oil led to an increase in its stability against oxidation. The phenolic content of cold pressed tiger nut oil was about 3.3 times as high as that of sunflower oil. The analytical data showed that the lowest deterioration during the frying process occurred in tiger nut oil and the highest in sunflower. The changes in the physico-chemical parameters were controlled and significantly (P < 0.05 decreased when tiger nut /sunflower oil (W/W proportions were varied between 20/80 to 50/50. The obtained results indicate that mixing sunflower oil with cold pressed tiger nut oil increased the stability and hence improved the quality of sunflower oil during the frying process.

Aceites de girasol se mezclaron con diferentes niveles de aceite de chufa prensado en frío. Se obtuvieron mezclas de aceite de chufa con girasol en las proporciones: 0:100, 10: 90, 20: 80, 30

Effect of the use of olive–pomace oil biodiesel/diesel fuel blends in a compression ignition engine: Preliminary exergy analysis

International Nuclear Information System (INIS)

López, I.; Quintana, C.E.; Ruiz, J.J.; Cruz-Peragón, F.; Dorado, M.P.

2014-01-01

Highlights: • Olive–pomace oil (OPO) biodiesel constitute a new second-generation biofuel. • Exergy efficiency and performance of OPO biodiesel, straight and blended with diesel fuel was evaluated. • OPO biodiesel, straight and blended, provided similar performance parameters. • OPO biodiesel, straight and blended, provided similar exergy efficiency compared to diesel fuel. • OPO biodiesel, straight and blended, provided no exergy cost increment compared to diesel fuel. - Abstract: Although biodiesel is among the most studied biofuels for diesel engines, it is usually produced from edible oils, which gives way to controversy between the use of land for fuel and food. For this reason, residues like olive–pomace oil are considered alternative raw materials to produce biodiesel that do not compete with the food industry. To gain knowledge about the implications of its use, olive–pomace oil methyl ester, straight and blended with diesel fuel, was evaluated as fuel in a direct injection diesel engine Perkins AD 3-152 and compared to the use of fossil diesel fuel. Performance curves were analyzed at full load and different speed settings. To perform the exergy balance of the tested fuels, the operating conditions corresponding to maximum engine power values were considered. It was found that the tested fuels offer similar performance parameters. When straight biodiesel was used instead of diesel fuel, maximum engine power decreased to 5.6%, while fuel consumption increased up to 7%. However, taking into consideration the Second Law of the Thermodynamics, the exergy efficiency and unitary exergetic cost reached during the operation of the engine under maximum power condition for the assessed fuels do not display significant differences. Based on the exergy results, it may be concluded that olive–pomace oil biodiesel and its blends with diesel fuel may substitute the use of diesel fuel in compression ignition engines without any exergy cost increment

Vegetable oil and fat viscosity forecast models based on iodine number and saponification number

International Nuclear Information System (INIS)

Toscano, G.; Riva, G.; Foppa Pedretti, E.; Duca, D.

2012-01-01

Vegetable oil and fats can be considered as an important renewable source for the energy production. There are many applications where these biofuels are used directly in engines. However, the use of pure vegetable oils causes some problems as consequence of its chemical and physical characteristic. Viscosity is one of the most important parameters affecting several physical and mechanical processes of the operation of the engine. The determination of this parameter at different tis important to determine the behavior of the vegetable oil and fats. In this work we investigated the effects of two analytical chemical parameters (iodine number and saponification number) and forecasting models have been proposed. -- Highlights: ► Vegetable oil and fat viscosity is predicted by mathematical model based on saponification number and iodine number. ► Unsaturated vegetable oils with small size molecules of fatty acids have a lower viscosity values. ► The models proposed show an average error lower than 12%

Characterization of the lubricity of bio-oil/diesel fuel blends by high frequency reciprocating test rig

International Nuclear Information System (INIS)

Xu, Yufu; Wang, Qiongjie; Hu, Xianguo; Li, Chuan; Zhu, Xifeng

2010-01-01

The diesel fuel was mixed with the rice husk bio-oil using some emulsifiers based on the theory of Hydrophile-Lipophile Balance (HLB). The lubricity of the bio-oil/diesel fuel blend was studied on a High Frequency Reciprocating Test Rig (HFRR) according to ASTM D 6079-2004. The microscopic topography and chemical composition on the worn surface were analyzed respectively using scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The profile and surface roughness of the rubbed trace were measured using a profilometer. The chemical group and composition were studied by a Fourier transform infrared spectrometry (FTIR). The results showed that the lubrication ability of the present fuel blend was better than that of the Chinese conventional diesel fuel (number zero). However, the anti-corrosion and anti-wear properties of the fuel blend were not satisfactory in comparison with those of conventional diesel fuel.

Effect of Blended Feedstock on Pyrolysis Oil Composition

Energy Technology Data Exchange (ETDEWEB)

Smith, Kristin M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gaston, Katherine R [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-28

Current techno-economic analysis results indicate biomass feedstock cost represents 27% of the overall minimum fuel selling price for biofuels produced from fast pyrolysis followed by hydrotreating (hydro-deoxygenation, HDO). As a result, blended feedstocks have been proposed as a way to both reduce cost as well as tailor key chemistry for improved fuel quality. For this study, two feedstocks were provided by Idaho National Laboratory (INL). Both were pyrolyzed and collected under the same conditions in the National Renewable Energy Laboratory's (NREL) Thermochemical Process Development Unit (TCPDU). The resulting oil properties were then analyzed and characterized for statistical differences.

Cold Storage Stability of Blend Oil from Soybean Oil and Palm Oil with Different Melting Points%大豆油调和不同熔点棕榈液油的冷藏试验

Institute of Scientific and Technical Information of China (English)

吴苏喜; 刘立萍; 李慧; Ooi Cheng KEAT

2012-01-01

In order to provide references for preparing blend oil from soybean oil and palm oil with different melting points, the effects of different types and amounts of anti-crystallization agent and soybean oil-to-palm oil ratio on the cold storage stability of blend oil were studied. The best anti-crystallization agent was hydroxyl stearin at a dose of 0.025%. The blend oil A composed of 70% soybean oil, 30% palm olein with melting point of 10 ℃ and 0.025% hydroxy stearin could be kept transparent for more than 16 hours at 0 ℃ and more than 72 h at 5℃. The blend oil B composed of 70% soybean oil, 30% palm olein with melting point of 18 ℃ and 0.025% hydroxy stearin could be kept transparent for more than 30 h at 10℃. The blend oil C composed of 60% soybean oil, 40% palm olein with melting point of 18 ℃ and 0.025% hydroxy stearin could be kept transparent for more than 20 h at 15℃. The blend oil D composed of 60% soybean oil, 40% μm olein with melting point of 24℃ and 0.025% hydroxy stearin could be kept transparent for more than 10 h.%为了制备适应不同储存温度的豆油．棕榈液油调和油，以大豆油与不同熔点棕榈液油为原料，采用冷藏试验方法优化抑晶剂种类、用量和调和油配方。结果表明，羟基硬脂精是效果最佳的抑晶剂，其最佳添加量为0．025％；调和油1（豆油70％＋10℃棕榈油30％＋羟基硬脂精0．025％）在0℃环境下储存可保持16h以上澄清透亮，在5℃条件可保持72h以上澄清透亮；调和油2（豆油70％＋18℃棕榈油30％＋羟基硬脂精0．025％）在10℃环境下可保持30h以上澄清透亮；调和油3（豆油60％＋18℃棕榈油40％＋羟基硬脂精0．025％）在15℃环境下可保持20h以上澄清透亮；调和油4（豆油60％＋24℃棕榈油40％＋羟基硬脂精0．025％）在20℃环境下可保持10h以上澄清透亮。

Postprandial lipid responses of butter blend containing fish oil in a single-meal study in humans

DEFF Research Database (Denmark)

Overgaard, Julie; Porsgaard, Trine; Guo, Zheng

2008-01-01

blend with fish oil (352 mg n-3 long-chain PUFA (LCPUFA)) or the commercial butter blend. Blood samples were collected after the meals and in the fasting condition on the test day and the following morning, and were analysed for cholesterol absorption, plasma lipid profile and fatty acid composition....... No significant difference in the postprandial plasma fatty acid composition was observed between the groups, neither difference in cholesterol absorption, plasma cholesterol or the cholesterol contents of plasma lipoproteins. The incorporation of fish oil in the butter resulted in a significant lower......The postprandial effects of a butter product containing fish oil were investigated in a single-meal, randomized crossover study with a commercial butter product as the control. Twelve healthy males consumed two test meals with (13)C-labelled cholesterol (45 mg) and either an interesterified butter...

Preparation of Starch/Gelatin Blend Microparticles by a Water-in-Oil Emulsion Method for Controlled Release Drug Delivery

OpenAIRE

Phromsopha, Theeraphol; Baimark, Yodthong

2014-01-01

Information on the preparation and properties of starch/gelatin blend microparticles with and without crosslinking for drug delivery is presented. The blend microparticles were prepared by the water-in-oil emulsion solvent diffusion method. Glutaraldehyde and methylene blue were used as the crosslinker and the water-soluble drug model, respectively. The blend microparticles were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and UV-Vis spe...

Detection and quantification of adulteration of sesame oils with vegetable oils using gas chromatography and multivariate data analysis.

Science.gov (United States)

Peng, Dan; Bi, Yanlan; Ren, Xiaona; Yang, Guolong; Sun, Shangde; Wang, Xuede

2015-12-01

This study was performed to develop a hierarchical approach for detection and quantification of adulteration of sesame oil with vegetable oils using gas chromatography (GC). At first, a model was constructed to discriminate the difference between authentic sesame oils and adulterated sesame oils using support vector machine (SVM) algorithm. Then, another SVM-based model is developed to identify the type of adulterant in the mixed oil. At last, prediction models for sesame oil were built for each kind of oil using partial least square method. To validate this approach, 746 samples were prepared by mixing authentic sesame oils with five types of vegetable oil. The prediction results show that the detection limit for authentication is as low as 5% in mixing ratio and the root-mean-square errors for prediction range from 1.19% to 4.29%, meaning that this approach is a valuable tool to detect and quantify the adulteration of sesame oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

Science.gov (United States)

Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

2012-11-01

The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

Engine performance and emission characteristics of plastic oil produced from waste polyethylene and its blends with diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Yin, Sudong; Tan, Zhongchao [Department of Mechanical and Mechatronics Engineering, University of Waterloo (Canada)], Email: tanz@uwaterloo.ca

2011-07-01

This paper describes an experiment to determine the possibility of transforming waste plastics into a potential source of diesel fuel. Experiments were done on the use of various blends of plastic oil produced from waste polyethylene (WPE) with diesel fuel (D) at different volumetric ratios and the results were reviewed. WPE was thermally degraded with catalysis of sodium aluminum silicate at optimum conditions (414-480 degree celsius range and 1 h reaction time) and the collected oil was fractionated at various temperatures. The properties of the fuel blends at different volumetric ratios were measured in this study. It was shown that these blends can be used as fuel in compression ignition engines without any modification. With respect to engine performance and exhaust emission, it was found that using a 5% WPE-D (WPE5) blend instead of diesel fuel reduced carbon monoxide (CO) emission. However, the results of experiment showed that carbon dioxide (CO2) emission and oxides of nitrogen (NOx) emission rose.

ZETA POTENTIAL AND COLOR INVESTIGATIONS OF VEGETABLE OIL BASED EMULSIONS AS ECO-FRIENDLY LUBRICANTS

Directory of Open Access Journals (Sweden)

ROMICĂ CREŢU

2017-06-01

Full Text Available In the past 10 years, the need for biodegradable lubricants has been more and more emphasized. The use of vegetable oils as lubricants offers several advantages. The vegetable oils are biodegradable; thus, the environmental pollution is minimal either during or after their use. The aim of this paper is to presents a preliminary study concerning the influence of some preparation conditions on the stability of vegetable oil-in-water (O/W emulsions as eco-friendly lubricants stabilized by nonionic surfactant. In this context, vegetable oil-in-water emulsions characteristics where assessed using microscopically observation and zeta potential. In addition, the color of these emulsions can be evaluated. It can be observed that the emulsions tend to stabilize in time.

LDL-cholesterol lowering activity of a blend of rice bran oil and safflower oil (8:2) in patients with hyperlipidaemia: a proof of concept, double blind, controlled, randomised parallel group study.

Science.gov (United States)

Malve, Harshad; Kerkar, Prafulla; Mishra, Nidheesh; Loke, Sanjita; Rege, N N; Marwaha-Jaspal, Ankita; Jainani, Kiran J

2010-11-01

Cardiovascular diseases have emerged as major health burden worldwide in recent times. Low density lipoprotein cholesterol (LDL-C) serves as the primary marker for cardiovascular diseases. Reports suggest that rice bran oil has antihyperlipidaemic properties. However, current evidence suggests that no single oil can provide the recommended dietary fat ratio. Hence the present study was undertaken in patients with hyperlipidaemia to study effects of substitution of the cooking oil with a blend of 80% rice bran oil and 20% safflower oil on LDL-C levels. The selected patients (n = 73) were randomly assigned either to the study oil group (blend under study) or control oil group (the oil which the patient was using before). The lipid profile was monitored monthly in these patients for 3 months during which they consumed the oil as per the randomisation. At each follow up, LDL-C levels showed a significant reduction from baseline in the study oil group and reduction was more than that observed in the control group. It was also observed that the percentage of the respondents was higher in the study oil group. At the end of the study period, 82% patients from this group had LDL levels less than 150 mg% as against 57% in the control group. Thus, the substitution of usual cooking oil with a blend of rice bran oil and safflower oil (8:2) was found to exert beneficial effects on the LDL-C levels shifting them to low-risk lipid category.

Production and comparison of fuel properties, engine performance, and emission characteristics of biodiesel from various non-edible vegetable oils: A review

International Nuclear Information System (INIS)

Ashraful, A.M.; Masjuki, H.H.; Kalam, M.A.; Rizwanul Fattah, I.M.; Imtenan, S.; Shahir, S.A.; Mobarak, H.M.

2014-01-01

Highlights: • Overview of current energy situation. • Overview of biology, distribution and chemistry of various non-edible oil resources. • Comparison of fuel properties of various biodiesels produced from various non-edible oils. • Comparison of engine performance and emission characteristics of reviewed biodiesels. - Abstract: Energy demand is increasing dramatically because of the fast industrial development, rising population, expanding urbanization, and economic growth in the world. To fulfill this energy demand, a large amount of fuel is widely used from different fossil resources. Burning of fossil fuels has caused serious detrimental environmental consequences. The application of biodiesel has shown a positive impact in resolving these issues. Edible vegetable oils are one of the potential feedstocks for biodiesel production. However, as the use of edible oils will jeopardize food supplies and biodiversity, non-edible vegetable oils, also known as second-generation feedstocks, are considered potential substitutes of edible food crops for biodiesel production. This paper introduces some species of non-edible vegetables whose oils are potential sources of biodiesel. These species are Pongamia pinnata (karanja), Calophyllum inophyllum (Polanga), Maduca indica (mahua), Hevea brasiliensis (rubber seed), Cotton seed, Simmondsia chinesnsis (Jojoba), Nicotianna tabacum (tobacco), Azadirachta indica (Neem), Linum usitatissimum (Linseed) and Jatropha curcas (Jatropha). Various aspects of non-edible feedstocks, such as biology, distribution, and chemistry, the biodiesel’s physicochemical properties, and its effect on engine performance and emission, are reviewed based on published articles. From the review, fuel properties are found to considerably vary depending on feedstocks. Analysis of the performance results revealed that most of the biodiesel generally give higher brake thermal efficiency and lower brake-specific fuel consumption. Emission results

An investigation of using biodiesel/marine diesel blends on the performance of a stationary diesel engine

International Nuclear Information System (INIS)

Kalligeros, S.; Zannikos, F.; Stournas, S.; Lois, E.; Anastopoulos, G.; Teas, Ch.; Sakellaropoulos, F.

2003-01-01

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high-energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. With the exception of rape seed oil which is the principal raw material for biodiesel fatty acid methyl esters, sunflower oil, corn oil and olive oil, which are abundant in Southern Europe, along with some wastes, such as used frying oils, appear to be attractive candidates for biodiesel production. In this paper, fuel consumption and exhaust emissions measurements from a single cylinder, stationary diesel engine are described. The engine was fueled with pure marine diesel fuel and blends containing two types of biodiesel, at proportions up to 50%. The two types of biodiesel appeared to have equal performance, and irrespective of the raw material used for their production, their addition to the marine diesel fuel improved the particulate matter, unburned hydrocarbons, nitrogen oxide and carbon monoxide emissions. (Author)

EFFECT OF VARIOUS VEGETABLE OILS ON THE LIPID PROFILE AND ANTIOXIDANT STATUS IN HYPERCHOLESTEROLAEMIC WISTAR RATS- A COMPARATIVE STUDY

Directory of Open Access Journals (Sweden)

Prasad Ravindra Manjeshwar

2017-02-01

Full Text Available BACKGROUND Various vegetable oils are used for cooking foods in India. Controversies have been created that consumption of certain vegetable oils cause atherogenesis. A little is known about the effect of vegetable oils in hypercholesterolaemic conditions. Hypercholesterolaemia, mainly the increased plasma Low-Density Lipoprotein (LDL cholesterol levels and Reactive Oxygen Species (ROS has been implicated in the early development and progression of atherosclerosis and Coronary Heart Diseases (CHD. Current study is designed to assess the effect of various vegetable oils such as coconut, sunflower, palm, olive oil and vanaspati on lipid profile and oxidative stress parameters in rats fed on a high-cholesterol diet. MATERIALS AND METHODS Hypercholesterolaemia is induced by supplementing cholesterol with the basal diet. Reference dose of various vegetable oils were administered once daily for 90 days. After the treatment period of 90 days, triacylglycerol, total cholesterol, HDL cholesterol, LDL cholesterol, VLDL cholesterol and oxidative stress parameters are estimated and analysed. RESULTS In the present study, we observed the lipid-lowering effect of various vegetable oils in rats fed with high-cholesterol diet. Administration of cholesterol showed increased level of lipid profile. Concurrent administration of various vegetable oils with high-cholesterol diet caused a significant decrease in serum total cholesterol, LDL and VLDL cholesterol. This conclusion is made based on the observation that the vegetable oils were able to restore, at least partially, the lipid profile of hypercholesterolaemic rats. A decline of antioxidant status associated with an increase in lipid peroxidation was observed in all the vegetable oil treated groups. Among the oils, coconut oil showed a mild increase in High-Density Lipoprotein (HDL and least increase in lipid peroxidation compared to other vegetable oils treated groups. CONCLUSION Results suggest that the

Sustainability aspects of biobased products : comparison of different crops and products from the vegetable oil platform

NARCIS (Netherlands)

Meesters, K.P.H.; Corré, W.J.; Conijn, J.G.; Patel, M.K.; Bos, H.L.

2012-01-01

This study focusses on the production of vegetable oil based products. A limited number of aspacts of the sustainability of the full chain (from agriculture to product at the factory gate) was evaluated. Three different vegetable oils were taken into account: palm oil, soy oil and rapeseed oil. Also

A COMPREHENSIVE STUDY OF DI DIESEL ENGINE PERFORMANCE WITHVEGETABLE OIL: AN ALTERNATIVE BIO-FUEL SOURCE OF ENERGY

Directory of Open Access Journals (Sweden)

A. K. Azad

2012-06-01

Full Text Available This study offers comprehensive details on the use of bio-fuel as a viable and alternative source of energy. The bio-fuel was prepared from vegetable oil, i.e., mustard oil and tested in a diesel engine in both pure form and as a diesel blend. The mustard oil blend proportions were 20%, 30%, 40% and 50% and named as bio-diesel blends B20, B30, B40 and B50. A fuel-testing laboratory determined the properties of the pure mustard oil fuel and its blends, i.e., density, viscosity, dynamic viscosity, carbon residue, flash point, fire point and calorific value. An assessment of engine performance, i.e., brake horsepower (bhp, brake specific fuel consumption (bsfc, brake thermal efficiency (bte and brake mean effective pressure (bmep etc., was carried out for pure diesel, pure mustard and the blends, both in laboratory conditions and under British Standard (BS conditions. Finally, an analysis and comparison was made of the effects of the various fuels on the different engine properties.

Combustion of soybean oil and diesel mixtures for heating purposes

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, Adriana Correa; Sanz, Jose Francisco [European University Miguel de Cervantes, Valladolid (Spain)], E-mail: acorrea@uemc.es; Hernandez, Salvador; Navas, Luis Manuel; Rodriguez, Elena; Ruiz, Gonzalo [University of Valladolid (Spain). Dept. of Agricultural and Forest Engineering; San Jose, Julio [University of Valladolid (Spain). Dept. of Energetic Engineering; Gomez, Jaime [University of Valladolid (Spain). Dept. of Communications and Signal Theory and Telematics Engineering

2008-07-01

Using blends of vegetable oils with petroleum derivates for heating purposes has several advantages over other energy application for vegetable oils. This paper presents the results of an investigation by use of soybean oil and diesel mixture as fuel for producing heat in conventional diesel installation. The paper is set out as follows: properties characterization of soybean oil as fuel and of diesel oil, as well as the mixture of both; selection of the mixture according to their physical chemical properties and how they adapt to conventional combustion installation; experimentation with the selected mixture, allowing the main combustion parameters to be measured; processing the collected data, values of combustion, efficiency and reduction of emissions. Conclusions show that the use of soybean oil and diesel mixture for producing heat energy in conventional equipment is feasible and beneficial for reduction emissions. (author)

A Novel Approach for Analyzing Water Diffusion in Mineral and Vegetable Oil-Paper Insulation

Directory of Open Access Journals (Sweden)

Bin Du

2014-04-01

Full Text Available Water diffusion characteristics of mineral and vegetable oil-paper insulation systems are important for insulation condition evaluation of oil-filled transformers. In this paper, we describe a novel application method of in situ attenuated total reflection Fourier transform infrared (ATR-FTIR approach for analyzing the diffusion process of water molecules in oil-immersed insulating paper. Two-dimensional correlation was used to analyze the 3700 cm-1 to 3000 cm- 1 hydroxyl peak. The observed results indicated that water molecules form two types of hydroxyl (OH with oil-impregnated paper in the diffusion process are weak and strong hydrogen bonds, respectively. 2D infrared correlation analysis revealed that three OH stretching vibration spectra absorption peaks was existed in hygroscopic vegetable oil-immersed insulating paper. And there are four OH stretching vibration spectra absorption peaks in mineral oil-immersed insulation paper. Furthermore, mineral oil-impregnated paper and vegetable oil-impregnated paper diffusion coefficients were obtained by nonlinear fitting.

Highly effective ionic liquids for biodiesel production from waste vegetable oils

Directory of Open Access Journals (Sweden)

Fathy A. Yassin

2015-03-01

Full Text Available As conventional energy sources deplete, the need for developing alternative energy resources which are environment friendly becomes more imperative. Vegetable oils are attracting increased interest in this purpose. The methanolysis of vegetable oil to produce a fatty acid methyl ester (FAME, i.e., biodiesel fuel was catalyzed by commercial ionic liquid and its chloride modification. The imidazolium chloride ionic liquid was frequently chosen for the synthesis of biodiesel. The dual-functionalized’ ionic liquid is prepared by a direct combination reaction between imidazolium cation and various metal chlorides such as CoCl2, CuCl2, NiCl2, FeCl3 and AlCl3. Imidazolium tetrachloroferrate was proved to be a selective catalyst for the methanolysis reaction at a yield of 97% when used at 1:10, catalyst: oil ratio for 8 h at 55 °C. Operational simplicity, reusability of the used catalyst for 8 times at least, high yields and no saponification are the key features of this methodology. The dynamic viscosity and density of the upgraded vegetable oil decreased from 32.1 cP and 0.9227 g/cm3 to 10.2 cP and 0.9044 g/cm3 respectively, compared to those of the base vegetable oil. The objective of this study was the synthesis and characterization of biodiesel using commercial ionic liquid and its chloride modification. The ionic liquid catalysts were characterized using FTIR, Raman spectroscopy, DSC, TG and UV.

The use of Koroch seed oil methyl ester blends as fuel in a diesel engine

International Nuclear Information System (INIS)

Gogoi, T.K.; Baruah, D.C.

2011-01-01

An experimental investigation was carried out on a small direct injection (DI) diesel engine, fuelling the engine with 10% (B10), 20% (B20), 30% (B30) and 40% (B40) blending of Koroch seed oil methyl ester (KSOME) with diesel. The performance and combustion characteristics of the engine at various loads are compared and analyzed. The results showed higher brake specific fuel consumption (BSFC) and lower brake thermal efficiency (BTE) for the KSOME blends. The engine indicated power (IP) was more for the blends up to B30, but found to be reduced for the blend B40 when compared to that of diesel. The engine combustion parameters such as pressure crank angle diagram, peak pressure, time of occurrence of peak pressure, net heat-release rate, cumulative heat release, ignition delay and combustion duration were computed. The KSOME blends exhibited similar combustion trend with diesel. However, the blends showed an early start of combustion with shorter ignition delay period. The study reveals the suitability of KSOME blends up to B30 as fuel for a diesel engine mainly used in generating sets and the agricultural applications in India without any significant drop in engine performance.

In vivo and in vitro effects of a blend of essential oils on rumen methane mitigation

NARCIS (Netherlands)

Castro-Montoya, J.; Peiren, N.; Cone, J.W.; Zweifel, B.; Fievez, V.; Campeneere, De S.

2015-01-01

The effect of Agolin Ruminant, a blend of essential oils, on methane (CH4) emissions were investigated in two in vivo experiments and in four in vitro experiments. In the in vivo experiments, four lactating dairy cows and four beef heifers were supplemented 0.2 g/d of the essential oils (ca. 2–4 ppm

Vegetable Oil-Based Hyperbranched Thermosetting Polyurethane/Clay Nanocomposites.

Science.gov (United States)

Deka, Harekrishna; Karak, Niranjan

2009-04-25

The highly branched polyurethanes and vegetable oil-based polymer nanocomposites have been showing fruitful advantages across a spectrum of potential field of applications. Mesua ferrea L. seed oil-based hyperbranched polyurethane (HBPU)/clay nanocomposites were prepared at different dose levels by in situ polymerization technique. The performances of epoxy-cured thermosetting nanocomposites are reported for the first time. The partially exfoliated structure of clay layers was confirmed by XRD and TEM. FTIR spectra indicate the presence of H bonding between nanoclay and the polymer matrix. The present investigation outlines the significant improvement of tensile strength, scratch hardness, thermostability, water vapor permeability, and adhesive strength without much influencing impact resistance, bending, and elongation at break of the nanocomposites compared to pristine HBPU thermoset. An increment of two times the tensile strength, 6 degrees C of melting point, and 111 degrees C of thermo-stability were achieved by the formation of nanocomposites. An excellent shape recovery of about 96-99% was observed for the nanocomposites. Thus, the formation of partially exfoliated clay/vegetable oil-based hyperbranched polyurethane nanocomposites significantly improved the performance.

Biodiesel's Characteristics Preparation from Palm Oil

Directory of Open Access Journals (Sweden)

Tilani Hamid

2010-10-01

Full Text Available Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio = 5 : 1, amount of NaOH used as catalyst = 3.5 gr, 4.5 gr, 5 gr and 5.5 gr and it takes about one hour time reaction. The ester (metil ester produced are separated from glycerin and washed until it takes normal pH (6-7 where more amount of catalyst used will decrease the ester (biodiesel produced. The results show that biodiesels' properties made by using 3.5 (M3.5 gr, 4.5 gr (M4.5 and 5 (M5.0 gr catalyst close to industrial diesel oil and the other (M5.5 closes to automotive diesel oil, while blending diesel oil with 20 % biodiesel (B20 is able to improve the diesel engine performances.

Grinding temperature and energy ratio coe cient in MQL grinding of high-temperature nickel-base alloy by using di erent vegetable oils as base oil

Institute of Scientific and Technical Information of China (English)

Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

2016-01-01

Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grind-ing temperature, and energy ratio coefficient of MQL grinding were compared among the seven veg-etable oil types. Results revealed that (1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding tem-perature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less vis-cous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid;and (7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7%energy ratio coefficient

Tariff Impact on the Domestic Price of Vegetable Oil in Iran and the Associated Issues

Directory of Open Access Journals (Sweden)

omid gilanpour

2015-05-01

Full Text Available This study uses vector error correction model to examine the effects of oilseeds, crude oil and vegetable oil tariffs on vegetable oil consumer price. Monthly data sets for the years 2004-2013 and VAR and VECM models were applied for this study. Research findings indicates only a long term equilibrium relation between the study variables .The effect of vegetable oil tariffs on consumer and producer price index are 0.4 and 0.07, respectively. Furthermore, one percent increase in the oil seeds and crude oil tariff, will increase consumer prices by 2.35, 0.19percent. The huge gap between the impacts of the two tariffs –e.g. oilseeds and crude oil tariffs- on consumer price shows that oil industries work with low efficiency. This practically doubles the impact of tariff on consumers. Accordingly, structural reform in the oil industry can develop oil production and prevent additional burden upon the consumer price.

HPLC-UV Polyphenolic Profiles in the Classification of Olive Oils and Other Vegetable Oils via Principal Component Analysis

Directory of Open Access Journals (Sweden)

Mireia Farrés-Cebrián

2016-12-01

Full Text Available High performance liquid chromatography-ultraviolet (HPLC-UV was applied to the analysis and characterization of olive oils and other vegetable oils. A chromatographic separation on a Zorbax Eclipse XDB-C8 reversed-phase column was proposed under gradient elution, employing 0.1% formic acid aqueous solution and methanol as mobile phase, for the determination of 14 polyphenols and phenolic acids, allowing us to obtain compositional profiles in less than 20 min. Acceptable sensitivity (limit of detection (LOD values down to 80 µg/L in the best of cases, linearity (r2 higher than 0.986, good run-to-run and day-to-day precisions (relative standard deviation (RSD values lower than 11.5%, and method trueness (relative errors lower than 6.8% were obtained. The proposed HPLC-UV method was then applied to the analysis of 72 oil samples (47 olive oils and 27 vegetable oils including sunflower, soy, corn, and mixtures of them. Analytes were recovered using a liquid–liquid extraction method employing ethanol:water 70:30 (v/v solution and hexane as extracting and defatting solvents, respectively. HPLC-UV polyphenolic profiles using peak areas were then analysed by principal component analysis (PCA to extract information from the most significant data contributing to the characterization and classification of olive oils against other vegetable oils, as well as among Arbequina and Picual olive oil varieties. PCA results showed a noticeable difference between olive oils and the other classes. In addition, a reasonable discrimination of olive oils as a function of fruit varieties was also encountered.

Biodiesel from vegetable oil as alternate fuel for C.I engine and feasibility study of thermal cracking: A critical review

International Nuclear Information System (INIS)

Ramkumar, S.; Kirubakaran, V.

2016-01-01

Highlights: • The C.V of biodiesel is less than diesel of about 10% on volume and 15% on mass basis. • Most forms of biodiesel and its blends with diesel have higher viscosity than diesel. • Biodiesel’s cost and by-product reduce its feasibility as a substitute fuel. • TGA & DCS of Pungamia Oil shows that Thermal cracking is an alternate to Biodiesel. - Abstract: The awareness about using eco friendly fuels like biodiesel is increasing every day. The Increase in global warming and energy crises due to fossil fuel has accelerated the search of bio fuels. Biodiesel is a promising fuel; it is available in a wide range in every part of the world. Most of the studies reveal that the performance of biodiesel is better than that of diesel. Except NOx, the major emissions are high in the case of fossil fuels. This paper reviews the performance and emission characteristics of biodiesel in C.I engines. The paper also reviews the influence of engine modifications, various additives, and various proportions of blends of biodiesel with diesel. The physical and thermal characteristics of biodiesel have a great influence in the performance and emission, and they are tabulated in this paper. This paper also attempts feasibility of admitting vegetable oil in IC engine through Thermal Cracking. Preliminary investigation shows encouraging results and reported in this paper.

Fuel properties of biodiesel from vegetable oils and oil mixtures. Influence of methyl esters distribution

International Nuclear Information System (INIS)

Martínez, G.; Sánchez, N.; Encinar, J.M.; González, J.F.

2014-01-01

In this work, the quality of biodiesel produced by basic transesterification from several vegetable oils (soybean, rapeseed, sunflower, high oleic sunflower, Cynara Cardunculus L., Brassica Carinata and Jatropha Curca) cultivated in Extremadura has been studied in detail. The influence of raw material composition on properties such as density, viscosity, cetane number, higher heating value, iodine and saponification values and cold filter plugging point has been verified. Other biodiesel properties such as acid value, water content and flash and combustion points were more dependent on characteristics of production process. Biodiesel produced by rapeseed, sunflower and high oleic sunflower oils transesterification have been biofuels with better properties according to Norm EN 14214. Finally, it has been tested that it is possible to use oils mixtures in biodiesel production in order to improve the biodiesel quality. In addition, with the same process conditions and knowing properties of biodiesel from pure oils; for biodiesel from oils mixtures, its methyl esters content, and therefore properties dependent this content can be predicted from a simple mathematical equation proposed in this work. - Highlights: • Biodiesel quality produced by basic transesterification from vegetable oils. • We examine influences of methyl esters distribution on biodiesel properties. • Biofuels from soybean, sunflower and rapeseed oils were with better properties. • Oils mixtures improve biodiesel quality to fulfill Norm EN 14214. • An equation to predict properties of biodiesel from oil mixtures is proposed

[Consumption of nuts and vegetal oil in people with type 1 diabetes mellitus].

Science.gov (United States)

Ferrer-García, Juan Carlos; Granell Vidal, Lina; Muñoz Izquierdo, Amparo; Sánchez Juan, Carlos

2015-06-01

Recent studies have demonstrated the cardiovascular benefits of the Mediterranean Diet, enriched with olive oil and nuts. People with diabetes, who have an increased risk of cardiovascular complications, could benefit greatly from following this type of eating pattern. Analysis of vegetable fats intake from nuts and olive oil in patients with 1 Diabetes Mellitus type (DM1). Transverse descriptive study comparing 60 people with type 1 Diabetes Mellitus (DM1) with 60 healthy individuals. We collect the frequency of consumption of vegetable oils and nuts and calculate the contribution of these foods in mono and polyunsaturated fatty acids (oleic acid, linoleic acid and α-linolenic acid). For data collection we designed a food frequency questionnaire specifically. We also collect anthropometric variables, cardiovascular risk factors and diabetes-related variables. Vegetable fat intake from vegetable oils (3.02 ± 1.14 vs 3.07 ± 1.27 portions/day, P = 0.822) and nuts (1.35 ± 2.24 vs 1.60 ± 2.44 portions/week, P = 0.560), was similar in both groups. The DM1 group consumed fewer portions of olive oil daily than the control group (2.55 ± 1.17 vs 3.02 ± 1.34 portions/day, P = 0.046). We detected a significantly lower intake of α-linolenic acid in the control group (1.13 ± 2.06 versus 2.64 ± 4.37 g/day, p = 0.018) while there were not differences in the rest of fatty acids (oleic acid 28.30 ± 18.13 vs 29.53 ± 16.90 g/day, P = 0.703; linoleic 13.70 ± 16.80 vs 15.45 ± 19.90 g/day, P = 0.605). In DM1, it not demonstrated an influence of the intake of vegetable fats and oils from nuts in the anthropometric, metabolic and diabetes-specific variables. In people with DM1, total intake of vegetable oils and nuts do not differ from the general population. However, the consumption of olive oil and the contribution of α-linolenic fatty acid derived from such fats are slightly lower than the general population. Although intake of vegetable oils and nuts in people with DM1

Ultrasound assisted PTC catalyzed saponification of vegetable oils using aqueous alkali.

Science.gov (United States)

Bhatkhande, B S; Samant, S D

1998-03-01

A few vegetable oils were saponified using aqueous KOH and different PTCs at room temperature in the presence of ultrasound. The extent of saponification was studied using the saponification value as a reference. Optimizations of various parameters such as time, selection of PTC, quantity of PTC, quantity of KOH and quantity of water were carried out using soyabean oil as a sample oil under sonication with stirring. To study the effect of ultrasound, the saponification was also carried out at 35 +/- 2 degrees C under different conditions, namely stirring, sonication, stirring and sonication, and heating at 100 degrees C. It was found that the heterogeneous liquid-liquid phase saponification of different vegetable oils using aq. KOH/CTAB was remarkably accelerated at 35 +/- 2 degrees C in the presence of ultrasound along with stirring.

Antibacterial, antifungal, and antiviral effects of three essential oil blends.

Science.gov (United States)

Brochot, Amandine; Guilbot, Angèle; Haddioui, Laïla; Roques, Christine

2017-08-01

New agents that are effective against common pathogens are needed particularly for those resistant to conventional antimicrobial agents. Essential oils (EOs) are known for their antimicrobial activity. Using the broth microdilution method, we showed that (1) two unique blends of Cinnamomum zeylanicum, Daucus carota, Eucalyptus globulus and Rosmarinus officinalis EOs (AB1 and AB2; cinnamon EOs from two different suppliers) were active against the fourteen Gram-positive and -negative bacteria strains tested, including some antibiotic-resistant strains. Minimal inhibitory concentrations (MICs) ranged from 0.01% to 3% v/v with minimal bactericidal concentrations from Origanum vulgare EOs was antifungal to the six Candida strains tested, with MICs ranging from 0.01% to 0.05% v/v with minimal fungicidal concentrations from 0.02% to 0.05% v/v. Blend AB1 was also effective against H1N1 and HSV1 viruses. With this dual activity, against H1N1 and against S. aureus and S. pneumoniae notably, AB1 may be interesting to treat influenza and postinfluenza bacterial pneumonia infections. These blends could be very useful in clinical practice to combat common infections including those caused by microorganisms resistant to antimicrobial drugs. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Prediction Primary Available Blend Biodiesel of Waste Oil from Aurantiochytrium sp. for General Diesel Engines

Directory of Open Access Journals (Sweden)

Shu-Yao Tsai

2018-01-01

Full Text Available Chemical and enzyme transesterification were compared by discussing preliminary transesterification of waste oil of Aurantiochytrium sp., which was then used in transesterification for the primary available blend biodiesel for a general diesel engine in this study. We made progress on the winterized characteristics of the waste oil’s biodiesel of Aurantiochytrium sp. and its biodiesel, which included the reactivity parameters and properties. This approach led to the development of a novel idea for the evaluation of kinetic parameters of winterization, along with obtaining the suitable operation and storage conditions of biodiesel. Therefore, the waste oil of Aurantiochytrium sp. could be developed for biodiesel production and successfully made into a suitable blend diesel. Overall, we acquired the best condition of mixtures and the highly mixed rate of petrodiesel: biodiesel = 80 : 20 (activation energy of winterization 21.32 kJ/mol; onset temperature of winterization -4.15 °C; heat of combustion 43.15 MJ/kg; kinematic viscosity 3.51 mm2/s; flash point 67.5 °C, which was an appropriate blend biodiesel from the waste oil’s biodiesel of Aurantiochytrium sp.

Self-consistent photothermal techniques: Application for measuring thermal diffusivity in vegetable oils

Science.gov (United States)

Balderas-López, J. A.; Mandelis, Andreas

2003-01-01

The thermal wave resonator cavity (TWRC) was used to measure the thermal properties of vegetable oils. The thermal diffusivity of six commercial vegetable oils (olive, corn, soybean, canola, peanut, and sunflower) was measured by means of this device. A linear relation between both the amplitude and phase as functions of the cavity length for the TWRC was observed and used for the measurements. Three significant figure precisions were obtained. A clear distinction between extra virgin olive oil and other oils in terms of thermal diffusivity was shown. The high measurement precision of the TWRC highlights the potential of this relatively new technique for assessing the quality of this kind of fluids in terms of their thermophysical properties.

Hydration of vegetable oils for high-grade Diesel fuel components; Hydrierung von Pflanzenoelen zu hochwertigen Dieselkraftstoffkomponenten

Energy Technology Data Exchange (ETDEWEB)

Endisch, M.; Olschar, M.; Kuchling, T. [TU Bergakademie Freiberg (Germany); Balfanz, U. [BP AG, Global Fuels Technology, Bochum (Germany)

2008-07-01

The legally regulated admixture of biogenic fuel components for diesel fuels are actually realized in Germany by an admixture of vegetable oil methylester (e.g. from rapeseed oil). The paper describes the hydration of vegetable oils as alternative to this procedure. Infrared and {sup 13}NMR spectroscopy were used to analyse the reaction kinetics for rapeseed, soy been and palm oil hydration. Experimental results of investigations under operational conditions using a continuous test facility and different vegetable oils identified the possibilities of this technology. The technology allows the high-yield production of diesel fuel components with certain numbers higher than average.

Evaluating lubricating capacity of vegetal oils using Abbott-Firestone curve

Science.gov (United States)

Georgescu, C.; Cristea, G. C.; Dima, C.; Deleanu, L.

2017-02-01

The paper presents the change of functional parameters defined on the Abbott-Firestone curve in order to evaluate the surface quality of the balls from the four ball tester, after tests done with several vegetable oils. The tests were done using two grades of rapeseed oil (degummed and refined) and two grades of soybean oil (coarse and degummed) and a common transmission oil (T90). Test parameters were 200 N and 0.576 m/s (1500 rpm) for 60 minutes. For the refined rapeseed oil, the changes in shape of the Abbott-Firestone curves are more dramatic, these being characterized by high values of Spk (the average value for the wear scars on the three balls), thus being 40% of the sum Svk + Sk + Spk, percentage also obtained for the soybean oil, but the value Spk being lower. For the degummed soybean oil, the profile height of the wear scars are taller than those obtained after testing the coarse soybean oil, meaning that the degumming process has a negative influence on the worn surface quality and the lubricating capacity of this oil. Comparing the surface quality of the wear scars on fixed tested balls is a reliable method to point out the lubricant properties of the vegetable oils, especially if they are compared to a “classical” lubricant as a non-additivated transmission mineral oil T90. The best surface after testing was obtained for the soybean oil, followed by T90 oil and the degummed grades of the soybean oil and rapeseed oil (these three giving very close values for the functional parameters), but the refined rapeseed oil generated the poorest quality of the wear scars on the balls, under the same testing conditions.

Design and screening of synergistic blends of SiO2 nanoparticles and surfactants for enhanced oil recovery in high-temperature reservoirs

International Nuclear Information System (INIS)

Le, Nhu Y Thi; Pham, Duy Khanh; Le, Kim Hung; Nguyen, Phuong Tung

2011-01-01

SiO 2 nanoparticles (NPs) were synthesized by the sol–gel method in an ultrasound reactor and monodispersed NPs with an average particle size of 10–12 nm were obtained. The synergy occurring in blending NPs and anionic surfactant solutions was identified by ultra-low interfacial tension (IFT) reduction measured by a spinning drop tensiometer (Temco500). The oil displacement efficiency of the synergistic blends and surfactant solutions at Dragon South-East (DSE) reservoir temperature was evaluated using contact angle measurement (Dataphysics OCA 20). It was found that SiO 2 /surfactant synergistic blends displace oil as well as their original surfactant solutions at the same 1000 ppm total concentration. Abundant slag appearing in the SiO 2 /surfactant medium during oil displacement could be attributed to an adsorption of surfactants onto the NPs. The results indicate that at a concentration of 1000 ppm in total, the original surfactant SS16-47A and its blend with SiO 2 NPs in the ratio of 8:2 exhibited an IFT reduction as high as fourfold of the IFT recorded for the DSE oil–brine interface and very high speed of oil displacement. Therefore, it could potentially be applicable to enhanced oil recovery (EOR) in high-temperature reservoirs with high hardness-injection-brine, like the one at DSE. This opens up a new direction for developing effective EOR compositions, which require less surfactant and are environmentally safer

Preparation of Starch/Gelatin Blend Microparticles by a Water-in-Oil Emulsion Method for Controlled Release Drug Delivery.

Science.gov (United States)

Phromsopha, Theeraphol; Baimark, Yodthong

2014-01-01

Information on the preparation and properties of starch/gelatin blend microparticles with and without crosslinking for drug delivery is presented. The blend microparticles were prepared by the water-in-oil emulsion solvent diffusion method. Glutaraldehyde and methylene blue were used as the crosslinker and the water-soluble drug model, respectively. The blend microparticles were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and UV-Vis spectroscopy. The functional groups of the starch and gelatin blend matrices were determined from the FTIR spectra. Blend microparticles with a nearly spherical shape and internal porous structure were observed from SEM images. The average particle size of the gelatin microparticles depended on the crosslinker ratio but not on the starch/gelatin blend ratio. The in vitro drug release content significantly decreased as the crosslinker ratio increased and the starch blend ratio decreased. The results demonstrated that the starch/gelatin blend microparticles should be a useful controlled release delivery carrier for water-soluble drugs.

Determination of vegetable oils and fats adulterants in diesel oil by high performance liquid chromatography and multivariate methods.

Science.gov (United States)

Brandão, Luiz Filipe Paiva; Braga, Jez Willian Batista; Suarez, Paulo Anselmo Ziani

2012-02-17

The current legislation requires the mandatory addition of biodiesel to all Brazilian road diesel oil A (pure diesel) marketed in the country and bans the addition of vegetable oils for this type of diesel. However, cases of irregular addition of vegetable oils directly to the diesel oil may occur, mainly due to the lower cost of these raw materials compared to the final product, biodiesel. In Brazil, the situation is even more critical once the country is one of the largest producers of oleaginous products in the world, especially soybean, and also it has an extensive road network dependent on diesel. Therefore, alternatives to control the quality of diesel have become increasingly necessary. This study proposes an analytical methodology for quality control of diesel with intention to identify and determine adulterations of oils and even fats of vegetable origin. This methodology is based on detection, identification and quantification of triacylglycerols on diesel (main constituents of vegetable oils and fats) by high performance liquid chromatography in reversed phase with UV detection at 205nm associated with multivariate methods. Six different types of oils and fats were studied (soybean, frying oil, corn, cotton, palm oil and babassu) and two methods were developed for data analysis. The first one, based on principal component analysis (PCA), nearest neighbor classification (KNN) and univariate regression, was used for samples adulterated with a single type of oil or fat. In the second method, partial least square regression (PLS) was used for the cases where the adulterants were mixtures of up to three types of oils or fats. In the first method, the techniques of PCA and KNN were correctly classified as 17 out of 18 validation samples on the type of oil or fat present. The concentrations estimated for adulterants showed good agreement with the reference values, with mean errors of prediction (RMSEP) ranging between 0.10 and 0.22% (v/v). The PLS method was

Performance Test on Compression Ignition Engine by Blending Ethanol and Waste Plastic Pyrolysis Oil with Cetane Additive

Science.gov (United States)

Padmanabhan, S.; Ganesan, S.; Jeswin Arputhabalan, J.; Chithrala, Varun; Ganesh Bairavan, P.

2017-05-01

The demand for diesel fuel is higher than that of petrol throughout the world hence seeking alternative to mineral diesel is a natural choice. Alternative fuels should be easily available at lower cost, environment friendly and fulfill energy needs without modifying engine’s operational parameters. Waste to energy is the trend in the selection of alternate fuels. In this work, Waste Plastic Pyrolysis oil (WPPO), Ethanol, Diesel blend with Cetane additive has been attempted as an alternative fuel. A Twin cylinder, Direct Injection engine was used to assess the engine performance and emission characteristics of waste plastic pyrolysis oil with cetane additive. Experimental results of blended plastic fuel and diesel fuel were compared.

Determination Of Adsorption And Paraffin Characterization Of Treatment To Adsorb Vegetable Oil

International Nuclear Information System (INIS)

Aminah, Neneng Siti; Mulijani, Sri; Sudirman; Ridwan

2004-01-01

Using vegetable oil repeatedly, beside affect on quality decline of food and the oil itself, it is harmful to human health. Some poisoning and carcinogenic symptom were founded with experiment using animals. According to that fact, the aim of the research is using paraffin and candle to adsorb used vegetable oil and to convert into solid sample, so it can be easily wasted. At first, 2 g of sample was poured into the heated oil, with gently stirrer until it turned cold and harden. Each sample and standard before and after treatment was characterized with Ftir, XRD, and DSc. The result shows that paraffins adsorbs 40 ml used vegetable oil with 2 g sample in proportion. That proportion is lower than the standard which can adsorb 66.67 ml vegetable oil in the same weight sample. The difference of paraffin and standard is caused by physical properties within that two materials, and it can be explained by Ftir, X-Ray Diffraction (XRD) and differential scanning calorimetry (DSc). Based on result of Ftir analysis, standard consented of saturated hydrocarbon compound (alkanes) whereas paraffin consisted of unsaturated hydrocarbon compound (alkenes). Infrared spectrum after treatment showed the changes of compound, O-H and esters group were formed and it shows characterised the adsorption process. The result of DSc analysis showed that crystalline the melting point of standard is 75,3 o C and paraffin is 54,17 o C. The result of analysis XRD, described that standard and paraffin before treatment are crystalline whereas after treatment are am orf

Biodiesel fuels from vegetable oils via catalytic and non-catalytic supercritical alcohol transesterifications and other methods: a survey

International Nuclear Information System (INIS)

Demirbas, Ayhan

2003-01-01

Vegetable oil fuels have not been acceptable because they were more expensive than petroleum fuels. With recent increases in petroleum prices and uncertainties concerning petroleum availability, there is renewed interest in vegetable oil fuels for Diesel engines. Dilution of oils with solvents and microemulsions of vegetable oils lowers the viscosity, but some engine performance problems still exist. The purpose of the transesterification process is to lower the viscosity of the oil. Pyrolysis produces more biogasoline than biodiesel fuel. Soap pyrolysis products of vegetable oils can be used as alternative Diesel engine fuel. Methyl and ethyl esters of vegetable oils have several outstanding advantages among other new renewable and clean engine fuel alternatives. The main factors affecting transesterification are the molar ratio of glycerides to alcohol, catalyst, reaction temperature and pressure, reaction time and the contents of free fatty acids and water in oils. The commonly accepted molar ratios of alcohol to glycerides are 6:1-30:1

Biodiesel production from Kutkura (Meyna spinosa Roxb. Ex.) fruit seed oil: Its characterization and engine performance evaluation with 10% and 20% blends

International Nuclear Information System (INIS)

Kakati, J.; Gogoi, T.K.

2016-01-01

Highlights: • Biodiesel is produced from Kutkura seed oil and its fatty acid composition is determined. • Important fuel properties of biodiesel derived from Kutkura seed oil are evaluated. • Properties of Kutkura seed oil and biodiesel are compared with other tree seed biodiesels. • Engine performance of 10% (B10) and 20% (B20) blending of Kutkura biodiesel is reported. • B10 and B20 showed better performance than conventional diesel fuel. - Abstract: Kutkura (Meyna spinosa Roxb.) is a plant species in the genus Meyna from the Rubiaceae family. Kutkura fruits are food items; the fruits and the leaves of the Kutkura plant are also used in traditional medicine. In this article, biodiesel produced from Kutkura fruit seed oil is characterized and compared with other tree seed based biodiesels. Oil content in Kutkura fruit seed was found 35.45%. Free fatty acid (FFA) content in the oil was 3.1%, hence base catalyzed transesterification was used directly for biodiesel production from Kutkura fruit seed oil. Kutkura fruit seed oil contained 7.187% palmitic, 5.382% stearic, 30.251% oleic and 52.553% linoleic acid. Calorific value, kinematic viscosity and density of Kutkura fruit seed oil were found 38.169 MJ/kg, 28.92 mm"2/s and 922.5 kg/m"3 respectively. However, after transesterification, these properties improved to 39.717 MJ/kg, 5.601 mm"2/s and 885.3 kg/m"3 respectively in case of the Kutkura fatty acid methyl ester (FAME). Apart from water content, all other properties of Kutkura FAME met the ASTM (D6751) and (EN14214) standards. Blending of Kutkura FAME with diesel up to 20% (vol.) however reduced water content down to an acceptable level of 0.038 wt.%. The kinematic viscosity also reduced to the level of conventional diesel after blending. Further, an engine performance study with biodiesel blends (B10 and B20) showed almost similar fuel consumption rate with diesel. Engine brake thermal efficiency (BTE) was more while the smoke emission was less with B

Effect of grape seed extract, Cistus ladanifer L., and vegetable oil supplementation on fatty acid composition of abomasal digesta and intramuscular fat of lambs.

Science.gov (United States)

Jerónimo, Eliana; Alves, Susana P; Dentinho, Maria T P; Martins, Susana V; Prates, José A M; Vasta, Valentina; Santos-Silva, José; Bessa, Rui J B

2010-10-13

Thirty-six lambs were used in a 6 week experiment to evaluate the effect of vegetable oil blend supplementation (0 vs 60 g/kg of dry matter (DM)) and two dietary condensed tannin sources, grape seed extract (0 vs 25 g/kg of DM) and Cistus ladanifer L. (0 vs 250 g/kg of DM), on fatty acid (FA) composition of abomasal digesta and intramuscular polar and neutral lipids. Grape seed extract did not affect the FA profile of abomasal digesta or muscle lipid fractions. C. ladanifer had a minor effect in lambs fed diets with no oil but greatly changed the abomasal and muscle FA profiles in oil-supplemented lambs. It decreased 18:0 and increased 18:1 trans-11 in abomasal digesta and increased 18:1 trans-11 and 18:2 cis-9,trans-11 (P = 0.062) in muscle neutral lipids, resulting in an important enrichment of meat 18:2 cis-9,trans-11 when compared to other oil-supplemented diets (19.2 vs 41.7 mg/100 g of muscle).

Encapsulation of vegetable oils as source of omega-3 fatty acids for enriched functional foods.

Science.gov (United States)

Ruiz Ruiz, Jorge Carlos; Ortiz Vazquez, Elizabeth De La Luz; Segura Campos, Maira Rubi

2017-05-03

Polyunsaturated omega-3 fatty acids (PUFAs), a functional component present in vegetable oils, are generally recognized as being beneficial to health. Omega-3 PUFAs are rich in double bonds and unsaturated in nature; this attribute makes them highly susceptible to lipid oxidation and unfit for incorporation into long shelf life foods. The microencapsulation of oils in a polymeric matrix (mainly polysaccharides) offers the possibility of controlled release of the lipophilic functional ingredient and can be useful for the supplementation of foods with PUFAs. The present paper provides a literature review of different vegetable sources of omega-3 fatty acids, the functional effects of omega-3 fatty acids, different microencapsulation methods that can possibly be used for the encapsulation of oils, the properties of vegetable oil microcapsules, the effect of encapsulation on oxidation stability and fatty acid composition of vegetable oils, and the incorporation of long-chain omega-3 polyunsaturated fatty acids in foods.

Replacement of dietary fish oil with vegetable oils improves the growth and flesh quality of large yellow croaker ( Larmichthys crocea)

Science.gov (United States)

Duan, Qingyuan; Mai, Kangsen; Shentu, Jikang; Ai, Qinghui; Zhong, Huiying; Jiang, Yujian; Zhang, Lu; Zhang, Chunxiao; Guo, Sitong

2014-06-01

We investigated the effect of the replacement of dietary fish oil with vegetable oils on the growth and flesh quality of large yellow croaker ( Larmichthys crocea). The basal diet (FO) was formulated to contain 66.5% fish meal and 6.4% menhaden fish oil; whereas the other 3 experimental diets were formulated by replacing the fish oil with 50% soybean oil (SO50), 100% soybean oil (SO100) and 100% palm oil (PO100), respectively. The 4 diets were randomly assigned to 4 floating sea cages (3.0 m × 3.0 m × 3.0 m), and each was stocked with 250 fish individuals with an initial average weight of 245.29 g ± 7.45 g. The fish were fed to apparent satiation twice a day at 5:00 and 17:00, respectively, for 12 weeks. Experimental analysis showed that the specific growth rate of fish fed SO50 or PO100 were significantly higher than that of fish fed FO or SO100 ( P0.05). Compared to FO diet, SO50, SO100 and PO100 diets led to substantial decreases in the liquid loss and water loss from fresh fillets (1 d, 4°C) ( Preplacement of fish oil with vegetable oils. These findings indicated that the growth performance and selected flesh quality properties (liquid holding capacity and TBARS value) of large yellow croaker were substantially improved by replacing dietary fish oil with vegetable oils.

Biodegradable Poly(D,L-Lactide)/Lipid Blend Microparticles Prepared by Oil-in-Water Emulsion Method for Controlled Release Drug Delivery

OpenAIRE

Yaowalak Srisuwan; Yodthong Baimark

2014-01-01

The effects of blend ratio and drug loading content of poly(D,L-lactide) (PDLL)/stearic acid blends on microparticle characteristics and drug release behaviors were evaluated. The blend microparticles were prepared by an oil-in-water emulsion solvent evaporation method for drug delivery of a poorly water-soluble model drug, indomethacin. The microparticles were characterized using a combination of scanning electron microscopy (SEM), light scattering particle size analysis, differential scanni...

Vegetable Oil-Based Hyperbranched Thermosetting Polyurethane/Clay Nanocomposites

Directory of Open Access Journals (Sweden)

Deka Harekrishna

2009-01-01

Full Text Available Abstract The highly branched polyurethanes and vegetable oil-based polymer nanocomposites have been showing fruitful advantages across a spectrum of potential field of applications.Mesua ferreaL. seed oil-based hyperbranched polyurethane (HBPU/clay nanocomposites were prepared at different dose levels by in situ polymerization technique. The performances of epoxy-cured thermosetting nanocomposites are reported for the first time. The partially exfoliated structure of clay layers was confirmed by XRD and TEM. FTIR spectra indicate the presence of H bonding between nanoclay and the polymer matrix. The present investigation outlines the significant improvement of tensile strength, scratch hardness, thermostability, water vapor permeability, and adhesive strength without much influencing impact resistance, bending, and elongation at break of the nanocomposites compared to pristine HBPU thermoset. An increment of two times the tensile strength, 6 °C of melting point, and 111 °C of thermo-stability were achieved by the formation of nanocomposites. An excellent shape recovery of about 96–99% was observed for the nanocomposites. Thus, the formation of partially exfoliated clay/vegetable oil-based hyperbranched polyurethane nanocomposites significantly improved the performance.

Combustion of biodiesel fuel produced from hazelnut soapstock/waste sunflower oil mixture in a Diesel engine

International Nuclear Information System (INIS)

Usta, N.; Oeztuerk, E.; Can, Oe.; Conkur, E.S.; Nas, S.; Con, A.H.; Can, A.C.; Topcu, M.

2005-01-01

Biodiesel is considered as an alternative fuel to Diesel fuel No. 2, which can be generally produced from different kinds of vegetable oils. Since the prices of edible vegetable oils are higher than that of Diesel fuel No. 2, waste vegetable oils and non-edible crude vegetable oils are preferred as potential low priced biodiesel sources. In addition, it is possible to use soapstock, a by-product of edible oil production, for cheap biodiesel production. In this study, a methyl ester biodiesel was produced from a hazelnut soapstock/waste sunflower oil mixture using methanol, sulphuric acid and sodium hydroxide in a two stage process. The effects of the methyl ester addition to Diesel No. 2 on the performance and emissions of a four cycle, four cylinder, turbocharged indirect injection (IDI) Diesel engine were examined at both full and partial loads. Experimental results showed that the hazelnut soapstock/waste sunflower oil methyl ester can be partially substituted for the Diesel fuel at most operating conditions in terms of the performance parameters and emissions without any engine modification and preheating of the blends

Relaxation dynamics and thermophysical properties of vegetable oils using time-domain reflectometry.

Science.gov (United States)

Sonkamble, Anil A; Sonsale, Rahul P; Kanshette, Mahesh S; Kabara, Komal B; Wananje, Kunal H; Kumbharkhane, Ashok C; Sarode, Arvind V

2017-04-01

Dielectric relaxation studies of vegetable oils are important for insights into their hydrogen bonding and intermolecular dynamics. The dielectric relaxation and thermo physical properties of triglycerides present in some vegetable oils have been measured over the frequency range of 10 MHz to 7 GHz in the temperature region 25 to 10 °C using a time-domain reflectometry approach. The frequency and temperature dependence of dielectric constants and dielectric loss factors were determined for coconut, peanut, soya bean, sunflower, palm, and olive oils. The dielectric permittivity spectra for each of the studied vegetable oils are explained using the Debye model with their complex dielectric permittivity analyzed using the Havriliak-Negami equation. The dielectric parameters static permittivity (ε 0 ), high-frequency limiting static permittivity (ε ∞ ), average relaxation time (τ 0 ), and thermodynamic parameters such as free energy (∆F τ ), enthalpy (∆H τ ), and entropy of activation (∆S τ ) were also measured. Calculation and analysis of these thermodynamic parameters agrees with the determined dielectric parameters, giving insights into the temperature dependence of the molecular dynamics of these systems.

Tensão superficial estática de soluções aquosas com óleos minerais e vegetais utilizados na agricultura Surface tension of mineral oils and vegetable oils

Directory of Open Access Journals (Sweden)

Cristina G. de Mendonça

2007-01-01

Full Text Available O trabalho teve como objetivo avaliar a tensão superficial estática de soluções aquosas com formulações de óleos minerais e vegetais emulsionáveis utilizados como adjuvantes na agricultura. Os óleos minerais e vegetais, quando adicionados aos produtos fitossanitários, podem imprimir características desejáveis à calda de pulverização, como reduzir a tensão superficial em soluções aquosas, possibilitar maior contato da calda com a superfície vegetal ou reduzir o potencial de deriva durante as pulverizações. Foram testados os seguintes produtos comerciais: óleos minerais (Assist, Attach, Dytrol, Iharol, Mineral Oil, Spinner, Sunspray-E e Triona e óleos vegetais (Agrex'oil Vegetal, Crop Oil, Natur'l Óleo, Óleo Vegetal Nortox e Veget Oil, todos com registro de uso na agricultura. A tensão superficial das soluções aquosas foi avaliada em 11 concentrações para cada produto (0,025; 0,05; 0,1; 0,25; 0,5; 0,75; 1,0; 1,5; 2,0; 2,5 e 3,0% v/v. Essa propriedade dos óleos minerais e dos óleos vegetais foi estimada medindo-se a massa das gotas formadas na extremidade de uma bureta. Ao conjunto de dados obtidos para cada produto, na avaliação da tensão superficial, foram determinadas as análises de variância e de regressão, ajustando-se os dados ao Modelo de Mitscherlich. Entre os óleos minerais, destacaram-se os produtos: Assist, Dytrol, Iharol e Mineral Oil por apresentarem as menores tensões superficiais mínimas estimadas pelo Modelo, respectivamente, 29,255; 28,442; 26,097 e 28,584 mN m-1. Os óleos vegetais que apresentaram os menores valores de tensão superficial mínima estimados pelo Modelo, foram: Agrex' oil Vegetal (27,716 mN m-1, Natur'l óleo (28,216 mN m-1, Veget Oil (27,308 mN m-1 e Crop Oil (29,964 mN m-1.The aim of this work was to evaluate the surface tension of water emulsion with mineral oils and vegetable oils used as adjuvant. The mineral and vegetable oils when added to the agrochemicals can

Extent of Microbial Contamination of Refined and Unrefined Vegetable oils sold in South-west Nigeria

Directory of Open Access Journals (Sweden)

Oluwafemi Flora

2018-04-01

Full Text Available Oils constitute a major source of plant-based protein. A major limitation to optimal oil consumption in sub-tropical region is fungal infestation and consequent mycotoxin contamination. Ten refined and eight unrefined vegetable oils were randomly purchase from open markets and screened for microbial contamination using standard microbial procedures. Twenty six fungi isolates were obtained from the vegetable oil samples, the isolates were identified as Aspergillus fumigatus (43.0%, Mucor (17.9%, Saccharomyces cerevisiae (10.7%, Aspergillus niger (7.1%, Aspergillus flavus (7.1%, Penicillium spp (7.1%, Aspergillus oryzae (3.6%, Mucor (17.9% and Rhizopus spp (3.6%. Five out of the ten refined vegetable oil samples had no fungal contamination. A. flavus and A. oryzae were absent in all the refined oil samples while A. niger was absent in all the unrefined oil samples. Isolation of mycotoxigenic fungi such as Aspergillus spp. is of vital importance in the food industry. Education and training of processors and consumers is recommended.

Neural networks applied to characterize blends containing refined and extra virgin olive oils.

Science.gov (United States)

Aroca-Santos, Regina; Cancilla, John C; Pariente, Enrique S; Torrecilla, José S

2016-12-01

The identification and quantification of binary blends of refined olive oil with four different extra virgin olive oil (EVOO) varietals (Picual, Cornicabra, Hojiblanca and Arbequina) was carried out with a simple method based on combining visible spectroscopy and non-linear artificial neural networks (ANNs). The data obtained from the spectroscopic analysis was treated and prepared to be used as independent variables for a multilayer perceptron (MLP) model. The model was able to perfectly classify the EVOO varietal (100% identification rate), whereas the error for the quantification of EVOO in the mixtures containing between 0% and 20% of refined olive oil, in terms of the mean prediction error (MPE), was 2.14%. These results turn visible spectroscopy and MLP models into a trustworthy, user-friendly, low-cost technique which can be implemented on-line to characterize olive oil mixtures containing refined olive oil and EVOOs. Copyright © 2016 Elsevier B.V. All rights reserved.

New antioxidants and antioxidant systems for improvement of the stability of vegetable oils and fish oils

Science.gov (United States)

Most vegetable oils and fish oils contain polyunsaturated fatty acids ranging from 18 carbons with two to three double bonds, to 22 or 24 carbons, and up to six double bonds. Nutritional research over the years has indicated that individual fatty acids from the diet play a complex role in nutrition ...

Effect of dietary grape seed extract and Cistus ladanifer L. in combination with vegetable oil supplementation on lamb meat quality.

Science.gov (United States)

Jerónimo, Eliana; Alfaia, Cristina M M; Alves, Susana P; Dentinho, Maria T P; Prates, José A M; Vasta, Valentina; Santos-Silva, José; Bessa, Rui J B

2012-12-01

Thirty-six Merino Branco lambs were assigned to six dietary treatments: control diet (C) consisting of 90% dehydrated lucerne and 10% wheat bran; C with 6% of oil blend (CO); C with 2.5% of grape seed extract (GS); GS with 6% of oil blend (GSO); C with 25% of Cistus ladanifer (CL), and CL with 6% of oil blend (CLO). Meat lipid and colour stability was then evaluated during 7 days of storage. The effect of inclusion of grape seed extract and C. ladanifer in diets on meat sensory properties was also evaluated. Meat antioxidant potential, determined after oxidation induction by a ferrous/hydrogen peroxide system, decreased with oil supplementation (P<0.001), but inclusion of grape seed extract and C. ladanifer in diets protected the meat against lipid oxidation (P=0.036). Meat colour was not affected by diets. Inclusion of grape seed extract and C. ladanifer in diets did not change the sensory properties of meat. Copyright © 2012 Elsevier Ltd. All rights reserved.

Breads Fortified with Freeze-Dried Vegetables: Quality and Nutritional Attributes. Part II: Breads Not Containing Oil as an Ingredient

Directory of Open Access Journals (Sweden)

Viren Ranawana

2016-09-01

Full Text Available The present article describes the second part of a study investigating the effect of adding vegetables on the nutritional, physico-chemical, and oxidative properties of wheat bread, and specifically focuses on bread that does not contain oil as an added ingredient. Wheat flour breads fortified with freeze-dried carrot, tomato, beetroot or broccoli were developed and assessed for their nutritional composition, antioxidant potential, oxidative stability, and storage properties. Using a simulated in vitro model, the study also examined the impact of vegetable addition on the oxidative stability of macronutrients during gastro-intestinal digestion. Adding vegetables improved the nutritional and functional attributes of the oil-free breads. However, they demonstrated a lower antioxidant potential compared to their oil-containing counterparts. Similarly, the textural and storage properties of the oil-free vegetable breads were poorer compared to the oil-containing breads. As expected, in the absence of oil the oil-free breads were associated with lower lipid oxidation both in their fresh form and during gastro-intestinal digestion. Adding vegetables reduced protein oxidation in the fresh oil-free breads but had no effect during gastro-intestinal digestion. The impact of vegetables on macronutrient oxidation in the oil-free breads during digestion appears to be vegetable-specific with broccoli exacerbating it and the others having no effect. Of the evaluated vegetables, beetroot showed the most promising nutritional and physico-chemical benefits when incorporated into bread that does not contain added oil.

Experimental Study on the Production of Karanja Oil Methyl Ester and Its Effect on Diesel Engine

Directory of Open Access Journals (Sweden)

N Shrivastava

2012-11-01

Full Text Available Fast depletion of fossil fuel resources forces the extensive research on the alternative fuels. Vegetable oils edible or non edible can be a better substitute for the petroleum diesel. Karanja, a non edible oil can be a potential source to replace the diesel fuel. To investigate the feasibility of Karanja oil as an alternative diesel fuel, its biodiesel was prepared through the transesterification process. The Biodiesel was then subjected to performance and emission tests in order to assess its actual performance, when used as a diesel engine fuel. The data generated for the 20, 50 and 100 percent blended biodiesel were compared with base line data generated for neat diesel fuel. Result showed that the Biodiesel and its blend showed lower thermal efficiency. Emission of Carbon monoxide, unburned Hydrocarbon and smoke was found to be reduced where as oxides of nitrogen was higher with biodiesel and its blends. Keywords: alternate Diesel fuel; Biodiesel; Karanja oil methyl ester; performance and emission

Influence of a vegetable fat blend on the texture, microstructure and sensory properties of kashar cheese

Directory of Open Access Journals (Sweden)

Dinkçi, N.

2011-09-01

Full Text Available The possibility of using a commercial vegetable fat blend in Kashar cheese was investigated. Kashar cheeses were manufactured by replacing the milk fat (MF with a vegetable fat (VF blend. Kashar cheeses from whole milk were also manufactured to compare textural, microstructural, meltability, color and sensory characteristics during a ripening period of 90 days. The use of vegetable fat decreased the meltability, hardness, cohesiveness, gumminess and chewiness of the cheese; while increasing adhesiveness where springiness was not affected. Differences became less notable toward the end of ripening. Scanning electron micrographs displayed VF cheese with a compact network with small and uniform fat globules embedded in the protein matrix. The MF cheese exhibited an open protein matrix containing milk fat globules of various sizes and forms. The color analysis demonstrated significant differences between cheeses. Finally, all sensory characteristics of the cheese were affecte d by the vegetable fat blend.

La posibilidad de usar una mezcla de grasas vegetales comerciales en queso Kashar fue investigada. Los quesos Kashar fueron elaborados con una mezcla de grasas vegetales (VF en lugar de grasa de leche (MF. Quesos Kashar con leche entera fueron también elaborados para comparar las características sensoriales, de color, de fusión, microestructurales y de textura durante el periodo de maduración de 90 días. El uso de grasas vegetales decreció la dureza y las propiedades de fusión, de cohesión, de gomosidad y de masticación e incremento la adhesividad mientras que la elasticidad no fue afectada. Las diferencias se hicieron menos notables hacia el final de la maduración. La micrografía electrónica de barrido de quesos VF mostro una red compacta con pequeños y uniformes glóbulos de grasa embebidos en la matriz de proteínas. Los quesos MF exhibieron una matriz de proteínas abierta conteniendo glóbulos de grasa de leche de varios

Triacylglycerol composition, physico-chemical characteristics and oxidative stability of interesterified canola oil and fully hydrogenated cottonseed oil blends.

Science.gov (United States)

Imran, Muhammad; Nadeem, Muhammad

2015-10-29

Partial hydrogenation process is used worldwide to produce shortening, baking, and pastry margarines for food applications. However, demand for such products is decreased during last decade due to their possible links to consumer health and disease. This has raised the need to replace hydrogenation with alternative acceptable interesterification process which has advantage in context of modifying the physico-chemical properties of edible fat-based products. Therefore, the main mandate of research was the development of functional fat through chemical interesterification of canola oil (CaO) and fully hydrogenated cottonseed oil (FHCSO) mixtures. Blends were prepared in the proportions of 75:25 (T1), 50:50 (T2) and 25:75 (T3) of CaO:FHCSO (w/w). Interesterification was performed using sodium methoxide (0.2 %) as catalyst at 120 °C, under reduced pressure and constant agitation for 60 minutes. The non-interesterified and interesterified CaO:FHCSO blends were evaluated for triacylglycerol (TAG) composition, physico-chemical characteristics, oxidative stability and consumer acceptability at 0, 30 and 60 days of storage interval. The oleic acid (58.3 ± 0.6 %) was predominantly present in CaO while the contents of stearic acid (72 ± 0.8 %) were significantly higher in FHCSO. Maximum trisaturated (S3) contents (63.9 ± 0.5 %) were found in T3 while monounsaturated (S2U), diunsaturated (U2S) and triunsaturated (U3) contents were quite low in T2 and T3 before interesterification. A marked reduction in S3 and U3 contents with concomitant increase in S2U and U2S contents was observed for all CaO:FHCSO blends on interesterification. During storage, the changes in S3, S2U and U2S contents were not found significant (p ≥ 0.05). However, maximum decrease 13 %, 7.5 and 5.6 % in U3 contents for T1, T2 and T3 was noted after 60-days of interesterification, respectively. The Lovibond color R, melting point, refractive index, specific gravity, peroxide and free

Influence of enzymatic and chemical interesterification on crystallisation properties of refined, bleached and deodourised (RBD) palm oil and RBD palm kernel oil blends.

Science.gov (United States)

Norizzah, Abd Rashid; Nur Azimah, Kamarulzaman; Zaliha, Omar

2018-04-01

Interesterification reaction involves rearrangement of the fatty acid radicals on the glycerol backbone, either randomly (chemical interesterification) or regioselectivity (enzymatic interesterification). Refined, bleached and deodourised palm oil (RBDPO) and palm kernel oil (RBDPKO) were blended in ratios from 25:75 to 75:25 (wt/wt). All blends were subjected to enzymatic (EI) and chemical interesterification (CI) using Lipozyme TL IM (4% w/w) and sodium methoxide (0.2% m/m) as the catalysts, respectively. The effect of EI and CI on the triacylglycerol (TAG) composition, thermal behaviour, polymorphism, crystal morphology and crystallisation kinetics were studied. The aim of this research is to characterise the nature of crystals in food product for certain desired structure. The crystallisation behaviour discussed in this study involves microstructure (PLM), polymorphism (XRD), thermal properties and crystallisation kinetics by DSC. The alteration in TAG composition was greater after CI as compared to EI with the reduction of LaLaLa (from 11.00% to 5.15%) and POO (from 14.28% to 4.87%). The DSC complete melting and crystallisation temperature of blend with 75% PO increased after CI, from 39.58 °C to 41.67 °C and from -30.84 °C to -28.33 °C, respectively. EI contributed to finer crystals than CI. However, the β' and β polymorph mixture and crystallisation kinetics (n = 2) of PO-PKO blends did not change after CI and EI. The knowledge on controlling crystallisation of RBDPO and RBDPKO blends is vital for proper processing condition like margarine production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Disinfection of vegetable seed by treatment with essential oils, organic acids and plant extract

NARCIS (Netherlands)

Wolf, van der J.M.; Birnbaum, Y.E.; Zouwen, van der P.S.; Groot, S.P.C.

2008-01-01

Various essential oils, organic acids, Biosept, (grapefruit extract), Tillecur and extracts of stinging nettle and golden rod were tested for their antimicrobial properties in order to disinfect vegetable seed. In in vitro assays, thyme oil, oregano oil, cinnamon oil, clove oil and Biosept had the

Performance and emission of generator Diesel engine using methyl esters of palm oil and diesel blends at different compression ratio

Science.gov (United States)

Aldhaidhawi, M.; Chiriac, R.; Bădescu, V.; Pop, H.; Apostol, V.; Dobrovicescu, A.; Prisecaru, M.; Alfaryjat, A. A.; Ghilvacs, M.; Alexandru, A.

2016-08-01

This study proposes engine model to predicate the performance and exhaust gas emissions of a single cylinder four stroke direct injection engine which was fuelled with diesel and palm oil methyl ester of B7 (blends 7% palm oil methyl ester with 93% diesel by volume) and B10. The experiment was conducted at constant engine speed of 3000 rpm and different engine loads operations with compression ratios of 18:1, 20:1 and 22:1. The influence of the compression ratio and fuel typeson specific fuel consumption and brake thermal efficiency has been investigated and presented. The optimum compression ratio which yields better performance has been identified. The result from the present work confirms that biodiesel resulting from palm oil methyl ester could represent a superior alternative to diesel fuel when the engine operates with variable compression ratios. The blends, when used as fuel, result in a reduction of the brake specific fuel consumption and brake thermal efficiency, while NOx emissions was increased when the engine is operated with biodiesel blends.

Heterogeneous hydrogenation of vegetable oils : A literature review

NARCIS (Netherlands)

Veldsink, JW; Bouma, MJ; Schoon, NH; Beenackers, AACM

1997-01-01

Hardening of vegetable oils is reviewed from an engineering point of view. The present review focuses on kinetics of the hydrogenation and relevant transport and adsorption steps. It aims to contribute to accelerate new research to improve substantially on selectivities in general and a decrease of

The effect of food type (fish nuggets or French fries) on oil blend degradation during repeated frying.

Science.gov (United States)

Flores-Álvarez, María Del Carmen; Molina-Hernández, Erika F; Hernández-Raya, José Concepción; Sosa-Morales, María Elena

2012-11-01

Oil that is reused multiple times for deep frying goes through changes in chemical composition and physical characteristics, affecting the quality of the fried foods. In this study, the effect of the food type (fish nuggets or French fries) on the degradation of an oil blend during the deep-fat frying of each food at 180°C during 12 days was determined, and the characteristics of the fried products were evaluated. The degradation of oil during repeated use was relatively faster when fish nuggets were fried than when French fries were fried, as higher values of total polar compounds were obtained. The results are useful for producers of French fries and fish nuggets, such as restaurants or fast foods sellers, providing them with practical guidelines within the permitted values established by the regulatory authorities. The studied foods have high economic importance and are different in their composition. Under the studied conditions, the tested oil blend may be used during 4 d (4 h per day) with a daily replenishment, without discarding the oil when frying fish nuggets, and must be discarded after 8 d when French fries are processed. This suggestion allows preparing safe fried foods for consumers. © 2012 Institute of Food Technologists®

Influence of Brazilian vegetable oils on mechanical resistence of hair fiber

Directory of Open Access Journals (Sweden)

Maria Valéria Velasco

2015-02-01

Full Text Available Associating the global trend of incorporating active compounds and plants in cosmetic formulations and the vast Brazilian biodiversity, the present work aimed to study the incorporation of Brazilian vegetable oils in hair conditioner formulations, evaluating the mechanical resistance of hair fibers. The following oils were incorporated into base formulations at 5.0 % (w/w: babassu, buriti, andiroba and pequi. The formulations were applied to samples of Caucasian hair, followed by several washing steps, then the evaluation of mechanical strength. It was found that there was no statistically significant difference in mechanical resistance between samples treated with oils and the control between the first and seventh wash cycles. This fact can be explained by the possible low penetration of oils into the cortex, a region responsible for the mechanical properties of the hair fiber, since the grease composition disfavors its diffusion. The common effects of vegetable oils on the cuticle, such as filling in cracks or cavities, lubrication, and increased protein hydrophobicity cannot be excluded. The oils tested in this work were not able to raise or protect hair tresses. However, additional studies are required in order to establish the effects of oil treatments, particularly in damaged hair.

Environmentally friendly properties of vegetable oil methyl esters

Directory of Open Access Journals (Sweden)

Gateau Paul

2005-07-01

Full Text Available Measurements were carried out on Vegetable Oil Methyl Esters (VOME or FAME answering the most recent specifications. The products tested are RME (Rapeseed oil Methyl Ester, ERME (Erucic Rapeseed oil Methyl Esters, SME (Sunflower oil Methyl Esters, and HOSME (High Oleic Sunflower oil Methyl Esters. They contain more than 99.5% of fatty acid mono esters. The compositions are given. VOME are not volatile and they are not easily flammable. They are not soluble in water and they are biodegradable. According to the methods implemented for the determination of the German classification of substances hazardous to waters WGK, they are not toxic on mammals and unlike diesel fuel they are not toxic on fish, daphnia, algae and bacteria. The RME is not either toxic for shrimps. According to tests on rabbits, RME and SME are not irritating for the skin and the eyes. VOME display particularly attractive environmental properties.

A new simplex chemometric approach to identify olive oil blends with potentially high traceability.

Science.gov (United States)

Semmar, N; Laroussi-Mezghani, S; Grati-Kamoun, N; Hammami, M; Artaud, J

2016-10-01

Olive oil blends (OOBs) are complex matrices combining different cultivars at variable proportions. Although qualitative determinations of OOBs have been subjected to several chemometric works, quantitative evaluations of their contents remain poorly developed because of traceability difficulties concerning co-occurring cultivars. Around this question, we recently published an original simplex approach helping to develop predictive models of the proportions of co-occurring cultivars from chemical profiles of resulting blends (Semmar & Artaud, 2015). Beyond predictive model construction and validation, this paper presents an extension based on prediction errors' analysis to statistically define the blends with the highest predictability among all the possible ones that can be made by mixing cultivars at different proportions. This provides an interesting way to identify a priori labeled commercial products with potentially high traceability taking into account the natural chemical variability of different constitutive cultivars. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of the use of waste vegetable oil based biodiesel on the landscape in diesel engines

Directory of Open Access Journals (Sweden)

Bereczky Akos

2017-01-01

Full Text Available Petroleum-based fuels are now widely known as environmentally unfriendly because of non-renewable supplies and its contribution to environmental pollution. The challenge, therefore is to ensure appropriate energy supplies at minimum cost. There is an increasing energy demand in the world and nowadays it can be fulfilled only on the basis of fossil fuels. Therefore, it is necessary to evolve a renewable energy source with lower environmental impact. One alternative solution can be oils of plant origin, like vegetable oils and non-edible oils. With waste vegetable oil methyl ester, biofuel dependency can be decreased. Therefore, the aim of this research paper is to analyze the economic and environmental effect of waste vegetable oil methyl ester compared to fossil fuels. In some cases only the age of vehicles could raise burdens to biofuel utilization in road vehicles. Transport and energy policy – on a large scale – can play an important role in fuel consumption. Author is aware that waste vegetable oil methyl ester can play only a limited role in biofuel substitution.

Burn drug made from ozonated vegetable oil mixture with white tumeric and cassava leaves extract

Directory of Open Access Journals (Sweden)

Moulydia Farah

2018-01-01

Full Text Available This research aims to create a burn treatment performed with ozonation process from a mixture of vegetable oil and added extracts of herbal ingredients. Ozonation on vegetable oils proven to kill bacteria and safe for the body. Ozonated vegetable oil produced from the ozone reactor batch process by doing a variety of extraction mixture to Oleozon® and vegetable oils. Then the results of ozonation is added extracts of herbal ingredients that cassava leaves and white turmeric to increase effectiveness in killing bacteria. Cassava leaves have anti-inflammatory agent, namely Vitamin C. While white turmeric Curcuma zedoaria have substance, which of the two compounds can inhibit and kill bacteria. The quality of ozonated oil (Oleozon® analytically were tested by the method of iodine number, acid number, peroxide number, and FTIR. Ozonation increased the peroxide and acid values for both oils, the increase being higher for mixture of coconut oil and soybean oil. The results of such mixing is then tested in bacteria to determine their effectiveness in killing the bacteria. The best ozonation condition is in an increase of 386,85% acid value, peroxide value about 102,91 meq/kg oil, and decrease in iodine number up to 21%. The result showed that under these conditions, ozonized oil has an antiseptic effect against Staphylococcus aureus. The final results of this study are expected to be a new innovation in the healing of skin wounds caused by burns as an anti-inflammatory that is effective, safe, and environmentally friendly.

Demonstration study on direct use of waste vegetable oil as car fuel

International Nuclear Information System (INIS)

Remoto, Yasuyuki; Zeeren, Nyamgerel; Ushiyama, Izumi

2009-01-01

Full text: Various kinds of vegetable oil and waste cooking oil are in fact used as car fuel all over the world. In general, 'bio-diesel' i.e. fatty acid methyl ester extracted from such oil is utilized as fuel for vehicles. However bio-diesel has some problems such as byproduct and waste materials created during transesterification. An alternative method is the direct use of vegetable oil as car fuel through installation of a heater unit in the car to decrease vegetable oil viscosity. However little data has been reported concerning this method. The authors of this study carried out performance tests on the direct use of waste cooking oil using a car with a heater unit and found its high potential. Moreover, the authors compared the environmental load of direct use with biodiesel and light oil by carrying out life cycle inventory to clarify the superiority of direct use. First, the authors made a car to test waste cooking oil as fuel by equipping a heater unit, filter and sub tank for light oil to a used Toyota Estima Diesel KD-CXR10G. The car can be driven on road using only waste cooking oil, although a little light oil is necessary for starting the engine. The authors, then, carried out chassis dynamo tests and on-road tests using the car. The car showed similar performance and could be driven on road for over half a year without any problems in both cases using either waste cooking oil or light oil as fuel. Next, authors carried out life cycle inventory and compared the environmental loads of direct use of waste cooking oil with biodiesel from waste cooking oil and light oil. The data for life cycle inventory were obtained from tests on direct use, from a factory in Japan for bio-diesel and from the Life Cycle Assessment Society of Japan database for light oil, respectively. The CO 2 emission rates were 73.9, 12.7 and 7.06 [kg-CO 2 / GJ] for light oil, bio-diesel from waste cooking oil and the direct use of waste cooking oil, respectively. The superiority of

Effect of feeding lambs with a tanniferous shrub (rockrose) and a vegetable oil blend on fatty acid composition of meat lipids.

Science.gov (United States)

Francisco, A; Alves, S P; Portugal, P V; Pires, V M R; Dentinho, M T; Alfaia, C M; Jerónimo, E; Prates, J A M; Santos-Silva, J; Bessa, R J B

2016-12-01

The effects of feeding Cistus ladanifer (Cistus) and a blend of soybean and linseed oil (1 : 2 vol/vol) on fatty acid (FA) composition of lamb meat lipids and messenger RNA (mRNA) expression of desaturase enzymes was assessed. In total, 54 male lambs were randomly assigned to 18 pens and to nine diets, resulting from the combination of three inclusion levels of Cistus (50 v. 100 v. 200 g/kg of dry matter (DM)) and three inclusion levels of oil (0 v. 40 v. 80 g/kg of DM). The forage-to-concentrate ratio of the diets was 1 : 1. Longissimus muscle lipids were extracted, fractionated into neutral (NL) and polar lipid (PL) and FA methyl esters obtained and analyzed by GLC. The expression of genes encoding Δ5, Δ6 and Δ9 desaturases (fatty acid desaturase 1 (FADS1), fatty acid desaturase 2 (FADS2) and stearoyl CoA desaturase (SCD)) was determined. Intramuscular fat, NL and PL contents were not affected by oil or Cistus. Oil supplementation reduced (P<0.05) 16:0, c9-16:1, 17:0, c9-17:1 and c9-18:1 FA and increased (P<0.05) 18:2n-6, 18:3n-3 and the majority of biohydrogenation intermediates in NL. Cistus alone had few effects on FA of NL but interacted with oil (P<0.05) by increasing t10-18:1,t10,t12-18:2,t10,c12-18:2 and t7,c9-18:2. The t10-/t11-18:1 ratio increased with both Cistus and oil levels. The c9, t11-18:2 did not increase (P<0.05) with both oil and Cistus dietary inclusion. Oil reduced c9-16:1, 17:0, c9-17:1,c9-18:1, 20:4n-6, 22:4n-6 and 20:3n-9 proportions in PL, and increased 18:2n-6, 18:3n-3, 20:3n-3 and of most of the biohydrogenation intermediates. The Cistus had only minor effects on FA composition of PL. Cistus resulted in a reduction (P<0.05) of 20:5n-3 and 22:6n-3 in the meat PL. The expression level of SCD mRNA increased (P=0.015) with Cistus level, although a linear relationship with condensed tannins intake (P=0.11) could not be established. FADS1 mRNA expressed levels increased linearly (P=0.019) with condensed tannins intake. In summary, the

Experimental investigation on Performance and Emission Characteristics of J20, P20, N20 Biodiesel blends and Sound Characteristics of P20 Biodiesel blend Used in Single Cylinder Diesel Engine

Science.gov (United States)

rajasekar, R.; karthik, N.; Xavier, Goldwin

2017-05-01

Present work provides the effect of biodiesel blends and Sound Characteristics of P20 Biodiesel blend compared with Performance and emission Characteristics of diesel. Methods and analysis biodiesel blends was prepared by the Transesterification Process. Experiments were conducted in single cylinder constant speed direct injection diesel engine for various test fuels. Research is mainly focused on pongamia oil. It was observed that a 20% Pongamia oil blends and its properties were similar to diesel. The results showed that 20% Pongamia oil blends gave better performance, less in noise and emission compared with ester of Jatropha and neem oil blends. Hence Pongamia blends can be used in existing diesel engine without compromising the engine performance.

PENINGKATAN KUALITAS DAN PROSES PEMBUATAN BIODIESEL DARI BLENDING MINYAK KELAPA SAWIT (PALM OIL DAN MINYAK KELAPA (COCONUT OIL DAN BANTUAN GELOMBANG ULTRASONIK

Directory of Open Access Journals (Sweden)

Hantoro Satriadi

2015-01-01

Full Text Available Keterbatasan solar sebagai sumber energi bahan bakunya tidak dapat diperbaharui menuntut adanya bahan baku alternatif yang dapat diperbaharui dan ramah lingkungan untuk pembuatan biodiesel. Reaksi utama produksi biodiesel adalah esterifikasi dan transestirifikasi yang berlangsung lambat dan membutuhkan banyak katalis dan alkohol. Reaksi yang terjadi belum sempurna dan belum memenuhi standar SNI dan ASTM. Untuk memperbaiki mutu biodiesel serta menghasilkan yield maksimal, maka dilakukan blending bahan baku antara minyak kelapa sawit dan minyak kelapa dan dengan bantuan gelombang ultrasonic. Penelitian ini bertujuan untuk mempelajari pengaruh variabel perbandingan volume minyak kelapa sawit dan minyak kelapa, perbandingan volume methanolminyak, dan persentase berat katalis terhadap minyak terhadap hasil atau yield biodiesel. Alat utama yang digunakan adalah reaktor yang dilengkapi pembangkit gelombang ultrasonic dengan temperature 60 oC, tekanan 1 atm, volume 3 liter, dan frekuensi 28 kHz. Variabel proses pada penelitian ini adalah perbandingan volume minyak sawit dan kelapa 2:1, 3:1, dan 4:1, pebandingan volume metanol-minyak 0,2:1, 0,25:1, dan 0,3:1, dan persentase berat katalis KOH terhadap minyak 0,3%, 0,5%, dan 0,7%. Hasil penelitian didapat konversi tertinggi dicapai pada variabel perbandingan volume minyak sawit dan kelapa 3:1, perbandingan volume metanol/minyak 0,25:1, dan persentase berat katalis terhadap minyak dengan yield 97,26%.[A Improvement of Quality and Process for Biodiesel Production from Palm Oil and Coconut Oil Blends with Ultrasound Assisted] Limitations of solar energy as a source of raw material cannot be renewed demands for alternative raw materials that are renewable and environmentally friendly for the manufacture of biodiesel. The main production of biodiesel reaction is esterification and transestirifikasi which runs slow and requires a lot of alcohol and a catalyst. Reactions that happen yet perfect, and has not met

Response surface methodology (RSM) based multi-objective optimization of fusel oil -gasoline blends at different water content in SI engine

International Nuclear Information System (INIS)

Awad, Omar I.; Mamat, R.; Ali, Obed M.; Azmi, W.H.; Kadirgama, K.; Yusri, I.M.; Leman, A.M.; Yusaf, T.

2017-01-01

Highlights: • The optimal ratio ratio of fusel oil–gasoline blended fuels is proposed. • The water content of fusel oil was reduced from 13.5% to 6.5%. • The heating value of fusel oil was improved by 13%. • FAWE 20 fuels were found to be optimal values with a high desirability of 0.707. • RSM was applied to optimize the engine performance and exhaust emissions. - Abstract: The main objective of this study is to determine the optimal blend ratio of fusel oil–gasoline before and after water extraction (FBWE10, FBWE20, FAWE10, and FAWE20) regarding the performance and emissions of spark ignition engine using response surface methodology (RSM). The multi-objective optimization is applied to maximize the brake power, brake thermal efficiency and minimize the brake specific fuel consumption (BSFC), NOx emission, HC emission and CO emission. The water content of fusel oil has been extracted by employing rotary extractor method. The experimental of this study has been carried out with different fusel oil–gasoline blends, different throttle valve opening position (15%, 30%, 45% and 60%) and different engine speed (1500, 2500, 3500 and 4500 rpm). All the developed models for responses were determined to be statistically significant at 95% confidence level. The study results reveal an improvement in heating value of fusel oil after water extraction with FAWE20 (80 vol% gasoline fuel, 20 vol% fusel oil after water extracted) as the optimally blended fuel. The best condition of engine parameters with FAWE20 were 55.4% of WOT for load and 4499 rpm engine speed. In additional of the optimal values with a high desirability of 0.707 were 62.511 kW, 241.139 g/kW h, 36%, 1895.913 ppm140.829 ppm and % for brake power, BSFC, BTE, NO x , HC and CO emissions respectively. The reduction of water content in fusel oil has a statistical significance influence to increases BTE, NO x emission and decreases the BSFC, HC and CO emissions.

The effect of maleinized linseed oil (MLO) on mechanical performance of poly(lactic acid)-thermoplastic starch (PLA-TPS) blends.

Science.gov (United States)

Ferri, J M; Garcia-Garcia, D; Sánchez-Nacher, L; Fenollar, O; Balart, R

2016-08-20

In this work, poly(lactic acid), PLA and thermoplastic starch, TPS blends (with a fixed content of 30wt.% TPS) were prepared by melt extrusion process to increase the low ductile properties of PLA. The TPS used contains an aliphatic/aromatic biodegradable polyester (AAPE) that provides good resistance to aging and moisture. This blend provides slightly improved ductile properties with an increase in elongation at break of 21.5% but phase separation is observed due to the lack of strong interactions between the two polymers. Small amounts of maleinized linseed oil (MLO) can positively contribute to improve the ductile properties of these blends by a combined plasticizing-compatibilizing effect. The elongation at break increases over 160% with the only addition of 6phr MLO. One of the evidence of the plasticizing-compatibilizing effect provided by MLO is the change in the glass transition temperature (Tg) with a decrease of about 10°C. Field emission scanning electron microscopy (FESEM) of PLA-TPS blends with varying amounts of maleinized linseed oil also suggests an increase in compatibility. Copyright © 2016 Elsevier Ltd. All rights reserved.

Finding the food-fuel balance. Supply and demand dynamics in global vegetable oil markets

Energy Technology Data Exchange (ETDEWEB)

Savanti, P.

2012-10-15

Demand for vegetable oils for food and biofuel use is expected to increase by an additional 23 million tonnes by 2016; however supply is expected to struggle to keep up with this demand, according to this Rabobank report. Vegetable oil stocks have reached a 38 year low this year due in large part to constraints such as land availability and adverse weather.

Evaluation of antioxidants stability by thermal analysis and its protective effect in heated edible vegetable oil

Directory of Open Access Journals (Sweden)

Seme Youssef Reda

2011-06-01

Full Text Available In this work, through the use of thermal analysis techniques, the thermal stabilities of some antioxidants were investigated, in order to evaluate their resistance to thermal oxidation in oils, by heating canola vegetable oil, and to suggest that antioxidants would be more appropriate to increase the resistance of vegetable oils in the thermal degradation process in frying. The techniques used were: Thermal Gravimetric (TG and Differential Scanning Calorimetry (DSC analyses, as well as an allusion to a possible protective action of the vegetable oils, based on the thermal oxidation of canola vegetable oil in the laboratory under constant heating at 180 ºC/8 hours for 10 days. The studied antioxidants were: ascorbic acid, sorbic acid, citric acid, sodium erythorbate, BHT (3,5-di-tert-butyl-4-hydroxytoluene, BHA (2, 3-tert-butyl-4-methoxyphenol, TBHQ (tertiary butyl hydroquinone, PG (propyl gallate - described as antioxidants by ANVISA and the FDA; and also the phytic acid antioxidant and the SAIB (sucrose acetate isobutyrate additive, which is used in the food industry, in order to test its behavior as an antioxidant in vegetable oil. The following antioxidants: citric acid, sodium erythorbate, BHA, BHT, TBHQ and sorbic acid decompose at temperatures below 180 ºC, and therefore, have little protective action in vegetable oils undergoing frying processes. The antioxidants below: phytic acid, ascorbic acid and PG, are the most resistant and begin their decomposition processes at temperatures between 180 and 200 ºC. The thermal analytical techniques have also shown that the SAIB antioxidant is the most resistant to oxidative action, and it can be a useful choice in the thermal decomposition prevention of edible oils, improving stability regarding oxidative processes.

Rapid determination of saponification value and polymer content of vegetable and fish oils by terahertz spectroscopy.

Science.gov (United States)

Jiang, Feng Ling; Ikeda, Ikuo; Ogawa, Yuichi; Endo, Yasushi

2012-01-01

A rapid method for determining the saponification value (SV) and polymer content of vegetable and fish oils using the terahertz (THz) spectroscopy was developed. When the THz absorption spectra for vegetable and fish oils were measured in the range of 20 to 400 cm⁻¹, two peaks were seen at 77 and 328 cm⁻¹. The level of absorbance at 77 cm⁻¹ correlated well with the SV. When the THz absorption spectra of thermally treated high-oleic safflower oils were measured, the absorbance increased with heating time. The polymer content in thermally treated oil correlated with the absorbance at 77 cm⁻¹. These results demonstrate that the THz spectrometry is a suitable non-destructive technique for the rapid determination of the SV and polymer content of vegetable and fish oils.

Soil TPH Concentration Estimation Using Vegetation Indices in an Oil Polluted Area of Eastern China

Science.gov (United States)

Zhu, Linhai; Zhao, Xuechun; Lai, Liming; Wang, Jianjian; Jiang, Lianhe; Ding, Jinzhi; Liu, Nanxi; Yu, Yunjiang; Li, Junsheng; Xiao, Nengwen; Zheng, Yuanrun; Rimmington, Glyn M.

2013-01-01

Assessing oil pollution using traditional field-based methods over large areas is difficult and expensive. Remote sensing technologies with good spatial and temporal coverage might provide an alternative for monitoring oil pollution by recording the spectral signals of plants growing in polluted soils. Total petroleum hydrocarbon concentrations of soils and the hyperspectral canopy reflectance were measured in wetlands dominated by reeds (Phragmites australis) around oil wells that have been producing oil for approximately 10 years in the Yellow River Delta, eastern China to evaluate the potential of vegetation indices and red edge parameters to estimate soil oil pollution. The detrimental effect of oil pollution on reed communities was confirmed by the evidence that the aboveground biomass decreased from 1076.5 g m−2 to 5.3 g m−2 with increasing total petroleum hydrocarbon concentrations ranging from 9.45 mg kg−1 to 652 mg kg−1. The modified chlorophyll absorption ratio index (MCARI) best estimated soil TPH concentration among 20 vegetation indices. The linear model involving MCARI had the highest coefficient of determination (R 2 = 0.73) and accuracy of prediction (RMSE = 104.2 mg kg−1). For other vegetation indices and red edge parameters, the R2 and RMSE values ranged from 0.64 to 0.71 and from 120.2 mg kg−1 to 106.8 mg kg−1 respectively. The traditional broadband normalized difference vegetation index (NDVI), one of the broadband multispectral vegetation indices (BMVIs), produced a prediction (R 2 = 0.70 and RMSE = 110.1 mg kg−1) similar to that of MCARI. These results corroborated the potential of remote sensing for assessing soil oil pollution in large areas. Traditional BMVIs are still of great value in monitoring soil oil pollution when hyperspectral data are unavailable. PMID:23342066

Experimental studies on the combustion characteristics and performance of a direct injection engine fueled with biodiesel/diesel blends

International Nuclear Information System (INIS)

Qi, D.H.; Chen, H.; Geng, L.M.; Bian, Y. ZH.

2010-01-01

Biodiesel is an alternative diesel fuel that can be produced from different kinds of vegetable oils. It is an oxygenated, non-toxic, sulphur-free, biodegradable, and renewable fuel and can be used in diesel engines without significant modification. However, the performance, emissions and combustion characteristics will be different for the same biodiesel used in different types of engine. In this study, the biodiesel produced from soybean crude oil was prepared by a method of alkaline-catalyzed transesterification. The effects of biodiesel addition to diesel fuel on the performance, emissions and combustion characteristics of a naturally aspirated DI compression ignition engine were examined. Biodiesel has different properties from diesel fuel. A minor increase in brake specific fuel consumption (BSFC) and decrease in brake thermal efficiency (BTE) for biodiesel and its blends were observed compared with diesel fuel. The significant improvement in reduction of carbon monoxide (CO) and smoke were found for biodiesel and its blends at high engine loads. Hydrocarbon (HC) had no evident variation for all tested fuels. Nitrogen oxides (NOx) were slightly higher for biodiesel and its blends. Biodiesel and its blends exhibited similar combustion stages to diesel fuel. The use of transesterified soybean crude oil can be partially substituted for the diesel fuel at most operating conditions in terms of the performance parameters and emissions without any engine modification.

Improvements to the Composition of Fusel Oil and Analysis of the Effects of Fusel Oil–Gasoline Blends on a Spark-Ignited (SI Engine’s Performance and Emissions

Directory of Open Access Journals (Sweden)

Suleyman Simsek

2018-03-01

Full Text Available With the increase of energy needs and environmental pollution, alcohol-based alternative fuels are used in spark-ignited (SI engines. Fusel oil, which is a by-product obtained through distillation of ethanol, contains some valuable alcohols. As alcohols are high-octane, they have an important place among the alternative fuels. Fusel also takes its place among those alternatives as it is high-octane and low on exhaust emissions. In this research, the effects of using blends of unleaded gasoline and improved fusel oil on engine performance and exhaust emissions were analyzed experimentally. A four-stroke, single-cylinder, spark-ignited engine was used in the experiments. The tests were conducted at a fixed speed and under different loads. The test fuels were blended supplying with fusel oil at rates incremented by 10%, up to 50%. Under each load, the engine’s performance and emissions were measured. Throughout the experiments, it has been observed that engine torque and specific fuel consumption increases as the amount of fusel oil in the blend is increased. Nitrogen oxide (NOx, carbon monoxide (CO, and hydrocarbon (HC emissions are reduced as the amount of fusel oil in the blends is increased.

Replacing Fish Oil with Vegetable Oils in Salmon Feed Increases Hepatic Lipid Accumulation and Reduces Insulin Sensitivity in Mice

DEFF Research Database (Denmark)

Midtbø, Lisa Kolden

Background: Due to a growing global aquaculture production, fish oil (FO) and fish meal (FM) are partly replaced with vegetable ingredients in aqua feed for Atlantic salmon. These replacements in the feed lead to an altered fatty acid composition in the salmon fillet. We aimed to investigate how...... these changes affects obesity development and insulin sensitivity in mice eating the salmon. In addition, we wanted to investigate how the background diet affects the antiobesity effect of FO. Results: Western diets (WDs) were produced containing salmon fed either FO (WD-FO), or with partly replacement (80......%) of FO with different vegetable oils (VOs); rape seed oil (WDRO), olive oil (WD-OO) or soybean oil (WD-SO). These diets were given to C57BL/6J mice, and mice had higher hepatic lipid accumulation and lower insulin sensitivity when given WD-SO compared with WD-FO. Mice given WD-SO had higher hepatic...

Recent developments in microbial oils production: a possible alternative to vegetable oils for biodiesel without competition with human food?

Directory of Open Access Journals (Sweden)

Gwendoline Christophe

2012-02-01

Full Text Available Since centuries vegetable oils are consumed as human food but it also finds applications in biodiesel production which is attracting more attention. But due to being in competition with food it could not be sustainable and leads the need to search for alternative. Nowdays microbes-derived oils (single cell oils seem to be alternatives for biodiesel production due to their similar composition to that of vegetable oils. However, the cold flow properties of the biodiesel produced from microbial oils are unacceptable and have to be modified by an efficient transesterification. Glycerol which is by product of transesterification can be valorised into some more useful products so that it can also be utilised along with biodiesel to simplify the downstream processing. The review paper discusses about various potent microorganisms for biodiesel production, enzymes involved in the lipid accumulation, lipid quantification methods, catalysts used in transesterification (including enzymatic catalyst and valorisation of glycerol.

A Comparative Study of Engine Performance and Exhaust Emissions Characteristics of Linseed Oil Biodiesel Blends with Diesel Fuel in a Direct Injection Diesel Engine

Science.gov (United States)

Salvi, B. L.; Jindal, S.

2013-01-01

This paper is aimed at study of the performance and emissions characteristics of direct injection diesel engine fueled with linseed oil biodiesel blends and diesel fuel. The comparison was done with base fuel as diesel and linseed oil biodiesel blends. The experiments were conducted with various blends of linseed biodiesel at different engine loads. It was found that comparable mass fraction burnt, better rate of pressure rise and BMEP, improved indicated thermal efficiency (8-11 %) and lower specific fuel consumption (3.5-6 %) were obtained with LB10 blend at full load. The emissions of CO, un-burnt hydrocarbon and smoke were less as compared to base fuel, but with slight increase in the emission of NOx. Since, linseed biodiesel is renewable in nature, so practically negligible CO2 is added to the environment. The linseed biodiesel can be one of the renewable alternative fuels for transportation vehicles and blend LB10 is preferable for better efficiency.

Optimization of refinery product blending by using linear programming

International Nuclear Information System (INIS)

Ristikj, Julija; Tripcheva-Trajkovska, Loreta; Rikaloski, Ice; Markovska, Liljana

1999-01-01

The product slate of a simple refinery consists mainly of liquefied petroleum gas, leaded and unleaded gasoline, jet fuel, diesel fuel, extra light heating oil and fuel oil. The quality of the oil products (fuels) for sale has to comply with the adopted standards for liquid fuels, and the produced quantities have to be comply with the market needs. The oil products are manufactured by blending two or more different fractions which quantities and physical-chemical properties depend on the crude oil type, the way and conditions of processing, and at the same time the fractions are used to blend one or more products. It is in producer's interest to do the blending in an optimal way, namely, to satisfy the requirements for the oil products quality and quantity with a maximal usage of the available fractions and, of course, with a maximal profit out of the sold products. This could be accomplished by applying linear programming, that is by using a linear model for oil products blending optimization. (Author)

Influence of vegetable oils fatty acid composition on reaction temperature and glycerides conversion to biodiesel during transesterification.

Science.gov (United States)

Pinzi, S; Gandía, L M; Arzamendi, G; Ruiz, J J; Dorado, M P

2011-01-01

Presence of unreacted glycerides in biodiesel may reduce drastically its quality. This is why conversion of raw material in biodiesel through transesterification needs to readjust reaction parameter values to complete. In the present work, monitoring of glycerides transformation in biodiesel during the transesterification of vegetable oils was carried out. To check the influence of the chemical composition on glycerides conversion, selected vegetable oils covered a wide range of fatty acid composition. Reactions were carried out under alkali-transesterification in the presence of methanol. In addition, a multiple regression model was proposed. Results showed that kinetics depends on chemical and physical properties of the oils. It was found that the optimal reaction temperature depends on both length and unsaturation degree of vegetable oils fatty acid chains. Vegetable oils with higher degree of unsaturation exhibit faster monoglycerides conversion to biodiesel. It can be concluded that fatty acid composition influences reaction parameters and glycerides conversion, hence biodiesel yield and economic viability. Copyright © 2010 Elsevier Ltd. All rights reserved.

The Influence and Compatibility of Vegetable Oils and other ...

African Journals Online (AJOL)

The vegetable oils used as skin permeation enhancers were selected on the basis of compatibility studies data. A total of eight monolithic systems were prepared by using different concentrations of drug-polymers-permeation enhancers. The permeation parameters, flux, permeability coefficient, enhancement ratio and ...

Analysis of polycyclic aromatic hydrocarbons in vegetable oils combining gel permeation chromatography with solid-phase extraction clean-up

DEFF Research Database (Denmark)

Fromberg, Arvid; Højgård, A.; Duedahl-Olesen, Lene

2007-01-01

system equipped with a GPC column (S-X3) and pre-packed silica SPE columns for the subsequent clean-up and finally gas chromatography-mass spectrometry (GC-MS) determination. The method was validated for the determination of PAHs in vegetable oils and it can meet the criteria for the official control...... of benzo[a]pyrene levels in foods laid down by the Commission of the European Communities. A survey of 69 vegetable oils sampled from the Danish market included olive oil as well as other vegetable oils such as rapeseed oil, sunflower oil, grape seed oil and sesame oil. Levels of benzo[a]pyrene in all......A semi-automatic method for the determination of polycyclic aromatic hydrocarbons (PAHs) in edible oils using a combined gel permeation chromatography/solid-phase extraction (GPC/SPE) clean-up is presented. The method takes advantage of automatic injections using a Gilson ASPEC XL sample handling...

Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine

International Nuclear Information System (INIS)

Usta, N.

2005-01-01

Vegetable oils and their methyl/ethyl esters are alternative renewable fuels for compression ignition engines. Different kinds of vegetable oils and their methyl/ethyl esters have been tested in diesel engines. However, tobacco seed oil and tobacco seed oil methyl ester have not been tested in diesel engines, yet. Tobacco seed oil is a non-edible vegetable oil and a by-product of tobacco leaves production. To the author's best knowledge, this is the first study on tobacco seed oil methyl ester as a fuel in diesel engines. In this study, potential tobacco seed production throughout the world, the oil extraction process from tobacco seed and the transesterification process for biodiesel production were examined. The produced tobacco seed oil methyl ester was characterized by exposing its major properties. The effects of tobacco seed oil methyl ester addition to diesel No. 2 on the performance and emissions of a four cycle, four cylinder turbocharged indirect injection (IDI) diesel engine were examined at both full and partial loads. Experimental results showed that tobacco seed oil methyl ester can be partially substituted for the diesel fuel at most operating conditions in terms of performance parameters and emissions without any engine modification and preheating of the blends. (Author)

Thermodynamic Compatibility, Crystallizability, Thermal, Mechanical Properties and Oil Resistance Characteristics of Nanostructure Poly (ethylene-co-methyl acrylate/Poly(acrylonitrile-co-butadiene Blends

Directory of Open Access Journals (Sweden)

Murugan N.

2017-12-01

Full Text Available This paper addresses the compatibility, morphological characteristics, crystallization, physico-mechanical properties and thermal stability of the melt mixed EMA/NBR blends. FTIR spectroscopy reveals considerable physical interaction between the polymers that explain the compatibility of the blends. DSC results confirm the same (compatibility and reveals that NBR hinders EMA crystallization. Mechanical and thermal properties of the prepared EMA/NBR blends notably enhance with increasing the fraction of EMA in the blends. Morphology study exhibit the dispersed particles in spherical shape in the nanometer level. Swelling and oil resistance study have also been carried out in details to understand the performance behaviour of these blends at service condition

Production of biodiesel from vegetable oils

Directory of Open Access Journals (Sweden)

Luque, Susana

2008-03-01

Full Text Available Biodiesel is produced by transesterification of triglycerides present in animal fat or vegetable oils, by displacing glycerine with a low molar mass alcohol. This resulting ester mixture has physico-chemical properties similar to those of petroleum diesel. This paper reviews the synthetic paths that lead to biodiesel by means of the catalytic transesterification of vegetable oils. Although methyl esters are at present the only ones produced at industrial scale, the use of ethanol, which can also be obtained from renewable resources, has been considered, since it would generate a cleaner and more biocompatible fuel.El biodiésel se produce mediante la transesterificación de triglicéridos, presentes en grasas animales o aceites vegetales, en un proceso en el que un alcohol de bajo peso molecular desplaza a la glicerina. La mezcla de esteres así resultante posee unas propiedades físico-químicas similares a las del diésel procedente de petróleo. En este artículo se revisan las vías de síntesis de biodiésel mediante la transesterificación catalítica de aceites vegetales. Aunque actualmente a escala industrial solo se producen ésteres metílicos, también se ha considerado el uso de etanol, ya que éste se obtiene también de fuentes renovables, generando así un combustible más limpio y biocompatible.

Mechanism of formation of 3-chloropropan-1,2-diol (3-MCPD) esters under conditions of the vegetable oil refining.

Science.gov (United States)

Šmidrkal, Jan; Tesařová, Markéta; Hrádková, Iveta; Berčíková, Markéta; Adamčíková, Aneta; Filip, Vladimír

2016-11-15

3-MCPD esters are contaminants that can form during refining of vegetable oils in the deodorization step. It was experimentally shown that their content in the vegetable oil depends on the acid value of the vegetable oil and the chloride content. 3-MCPD esters form approximately 2-5 times faster from diacylglycerols than from monoacylglycerols. It has been proved that the higher fatty acids content in the oil caused higher 3-MCPD esters content in the deodorization step. Neutralization of free fatty acids in the vegetable oil before the deodorization step by alkaline carbonates or hydrogen carbonates can completely suppress the formation of 3-MCPD esters. Potassium salts are more effective than sodium salts. Copyright © 2016 Elsevier Ltd. All rights reserved.

Green Diesel from Hydrotreated Vegetable Oil Process Design Study

NARCIS (Netherlands)

Hilbers, T.J.; Sprakel, Lisette Maria Johanna; van den Enk, L.B.J.; Zaalberg, B.; van den Berg, Henderikus; van der Ham, Aloysius G.J.

2015-01-01

A systematic approach was applied to study the process of hydrotreating vegetable oils. During the three phases of conceptual, detailed, and final design, unit operations were designed and sized. Modeling of the process was performed with UniSim Design®. Producing green diesel and jet fuel from

Physicochemical studies on sunflower oil blended with cold pressed tiger nut oil during the deep frying process; Estudios fisicoquimicos sobre mezclas de aceite de girasol con aceite de chufa prensado en frio durante el proceso de fritura

Energy Technology Data Exchange (ETDEWEB)

Al Rehah, F. M.; Anany, A. M.

2012-07-01

Sunflower oils were blended with different levels of cold pressed tiger nut oil. Blended oils were obtained by mixing tiger nut oil with sunflower oil at the volume ratios of 0:100, 10: 90, 20: 80, 30: 70, 40: 60, 50:50 and 100: 0. The effects of deep frying on physico-chemical parameters (Free Fatty Acid (FFA), Peroxide Value (PV), thiobarbituric acid value (TBA), iodine value, Total Polar Compounds (TPC), color and viscosity) were evaluated over 30 hours of the frying process. The total phenolic content of native oils was determined. GLC analysis was performed to illustrate the fatty acid composition of sunflower oil, tiger nut oil and binary mixtures of them as well as their oxidation rates. The pure and blended oils were heated at 180 degree centigrade {+-} 5 degree centigrade, then frozen French fried potatoes were fried every 30 min. Oil samples were taken every 5 h and the entire continuous frying period was 30 h. The results showed that fresh sunflower oil had significantly the highest value of COX (7.25); while tiger nut oil had significantly the lowest (2.24). Mixing sunflower oil with different levels of tiger nut oil led to an increase in its stability against oxidation. The phenolic content of cold pressed tiger nut oil was about 3.3 times as high as that of sunflower oil. The analytical data showed that the lowest deterioration during the frying process occurred in tiger nut oil and the highest in sunflower. The changes in the physico-chemical parameters were controlled and significantly (P < 0.05) decreased when tiger nut /sunflower oil (W/W) proportions were varied between 20/80 to 50/50. The obtained results indicate that mixing sunflower oil with cold pressed tiger nut oil increased the stability and hence improved the quality of sunflower oil during the frying process. (Author) 68 refs.

The use of Brazilian vegetable oils in nanoemulsions: an update on preparation and biological applications

Directory of Open Access Journals (Sweden)

Lisiane Bajerski

Full Text Available ABSTRACT Vegetable oils present important pharmacological properties, which gained ground in the pharmaceutical field. Its encapsulation in nanoemulsions is considered a promising strategy to facilitate the applicability of these natural compounds and to potentiate the actions. These formulations offer several advantages for topical and systemic delivery of cosmetic and pharmaceutical agents including controlled droplet size, protection of the vegetable oil to photo, thermal and volatilization instability and ability to dissolve and stabilize lipophilic drugs. For these reasons, the aim of this review is to report on some characteristics, preparation methods, applications and especially analyze recent research available in the literature concerning the use of vegetable oils with therapeutic characteristics as lipid core in nanoemulsions, specially from Brazilian flora, such as babassu (Orbignya oleifera, aroeira (Schinus molle L., andiroba (Carapa guaianiensis, casca-de-anta (Drimys brasiliensis Miers, sucupira (Pterodon emarginatus Vogel and carqueja doce (Stenachaenium megapotamicum oils.

Physical and sensory characteristics of pork sausages from enzymatically modified blends of lard and rapeseed oil during storage

DEFF Research Database (Denmark)

Cheong, L.Z.; Zhang, H.; Nersting, L.

2010-01-01

Physical and sensory characteristic of pork sausages produced from enzymatic interesterified blends of lard and rapeseed oil during storage were evaluated. All three enzymatic interesterified blends (IE90, IE70 and IE50) had ratios of unsaturated to saturated fatty acids within the range of 1.......47-2.84 which is favourable for cardiovascular disease risk reduction. Blends of IE90 and IE70 were found to have suitable solid fat content, melting and crystallization profile suitable for sausages production. Sausages were produced from blends of IE90 and IE70 with different muscle types (musculus...... longissimus dorsi and musculus sternomandibularis) and processing conditions such as cooling rates and final processing temperature. Cooling rate was found to have no significant (P>0.05) effect on hardness of the sausages throughout storage. Both musculus longissimus dorsi and high final processing...

The effect of nanoparticle surfactant polarization on trapping depth of vegetable insulating oil-based nanofluids