75 FR 68974 - Drawbridge Operation Regulation; Upper Mississippi River, Rock Island, IL

Science.gov (United States)

2010-11-10

..., has issued a temporary deviation from the regulation governing the operation of the Rock Island Railroad and Highway Drawbridge across the Upper Mississippi River, mile 482.9, at Rock Island, Illinois... Operations, telephone 202-366-9826. SUPPLEMENTARY INFORMATION: The U.S. Army Rock Island Arsenal requested a...

78 FR 18933 - Drawbridge Operation Regulations; Upper Mississippi River, Rock Island, IL

Science.gov (United States)

2013-03-28

... operating schedule that governs the Rock Island Railroad and Highway Drawbridge across the Upper Mississippi River, mile 482.9, at Rock Island, Illinois. The deviation is necessary to allow the Quad City Marathon..., Docket Operations, telephone (202) 366-9826. SUPPLEMENTARY INFORMATION: The U.S. Army Rock Island Arsenal...

78 FR 15292 - Drawbridge Operation Regulations; Upper Mississippi River, Rock Island, IL

Science.gov (United States)

2013-03-11

... schedule that governs the Rock Island Railroad and Highway Drawbridge, across the Upper Mississippi River, mile 482.9, at Rock Island, Illinois. The deviation is necessary to allow the River Bandits 5K Run/Walk...) 366-9826. SUPPLEMENTARY INFORMATION: The U.S. Army Rock Island Arsenal requested a temporary deviation...

78 FR 16411 - Drawbridge Operation Regulation; Upper Mississippi River, Rock Island, IL

Science.gov (United States)

2013-03-15

... operating schedule that governs the Rock Island Railroad and Highway Drawbridge across the Upper Mississippi River, mile 482.9, at Rock Island, Illinois. The deviation is necessary to allow the Quad City Heart...-366-9826. [[Page 16412

Uranium minerals in Upper Carboniferous rocks in the Nowa Ruda region

International Nuclear Information System (INIS)

Bareja, E.

1981-01-01

Results of mineralogical studies on uranium in Upper Carboniferous rocks (Glinik Beds - Westphalian C - D and Ludwikowice Beds - Stephanian) in the vicinities of Nowa Ruda (Central Sudetic Depression) are presented. Uranium mineralization is here related to sandstones and polymictic conglomerates with clay and clay-carbonate cement. The major uranium-bearing horizon was found in middle part of the Glinik Beds, and some increase in uranium content - at the base of that unit. In the case of Stephanian rocks, points with uranium mineralization were found in various parts of the Ludwikowice Beds sequence: in basal conglomerate horizon and platy sandstones. Uranium minerals mainly occur in cement of sandstones and conglomerates. They were mainly identified as uranium blende and minerals of the sulfate group - zippeite and uranopilite. Mineralized uranium-bearing horizons display mineral paragenesis typical of Upper Carboniferous rocks of the Central Sudetic Depression: uranium blende, pyrite, chalcopyrite, sphalerite and galena. (author)

Physicomechanical parameters of sedimentary rocks in eastern Sichuan, China

International Nuclear Information System (INIS)

Guo, Jian; Sun, Yan; Shu, Liangshu; Zhu, Wenbin; Wang, Feng; Li, Benliang; Liu, Deliang

2009-01-01

Rock samples were collected and selected from the sedimentary covering strata from Cambrian to Jurassic in eastern Sichuan, China, which belongs to the Upper Yangtze plate. Physicomechanical parameters were measured systematically. Based on parametric texture characteristics and observation data of geology, five regional layer-slip systems are derived. The five layer-slip systems correspond to five reservoir–cover systems, as the incompetent beds correspond to cover beds and the competent beds to reservoir beds. In comparison with the Middle and Lower Yangtze plates, the physicomechanical parameters, lithologic composition and structural characteristics are basically similar to the Upper Yangtze plate. This comparison offers some insight into the oil and gas reservoir–cover systems in the region

Plumes do not Exist: Plate Circulation is Confined to Upper Mantle

Science.gov (United States)

Hamilton, W. B.

2002-12-01

Plumes from deep mantle are widely conjectured to define an absolute reference frame, inaugurate rifting, drive plates, and profoundly modify oceans and continents. Mantle properties and composition are assumed to be whatever enables plumes. Nevertheless, purported critical evidence for plume speculation is false, and all data are better interpreted without plumes. Plume fantasies are made ever more complex and ad hoc to evade contradictory data, and have no predictive value because plumes do not exist. All plume conjecture derives from Hawaii and the guess that the Emperor-Hawaii inflection records a 60-degree change in Pacific plate direction at 45 Ma. Paleomagnetic latitudes and smooth Pacific spreading patterns disprove any such change. Rationales for other fixed plumes collapse when tested, and hypotheses of jumping, splitting, and gyrating plumes are specious. Thermal and physical properties of Hawaiian lithosphere falsify plume predictions. Purported tomographic support elsewhere represents artifacts and misleading presentations. Asthenosphere is everywhere near solidus temperature, so melt needs a tensional setting for egress but not local heat. Gradational and inconsistent contrasts between MORB and OIB are as required by depth-varying melt generation and behavior in contrasted settings and do not indicate systematically unlike sources. MORB melts rise, with minimal reaction, through hot asthenosphere, whereas OIB melts react with cool lithosphere, and lose mass, by crystallizing refractories and retaining and assimilating fusibles. The unfractionated lower mantle of plume conjecture is contrary to cosmologic and thermodynamic data, for mantle below 660 km is more refractory than that above. Subduction, due to density inversion by top-down cooling that forms oceanic lithosphere, drives plate tectonics and upper-mantle circulation. It organizes plate motions and lithosphere stress, which controls plate boundaries and volcanic chains. Hinge rollback is the

Uranium-polymetallic ore-forming system and mechanism of the black rock series in the southeast continental margin of Yangtze plate

International Nuclear Information System (INIS)

Qi Fucheng; Zhang Zilong; He Zhongbo; Li Zhixing; Wang Wenquan; Su Xiangli; Zhang Chao

2011-01-01

It is the indisputable fact that the large scale uranium-polymetallic mineralization had happen in the southeast continental margin of Yangtze plate. The rations of Fe/Ti, (Fe+Mn)/Ti, Al/(Al+Fe+Mn), and Ni-Co-Zn diagrams show that the siliceous rocks and phosphorites are the products of hydrothermal sedimentation in these area. In La/Yb-REE diagrams the data of phosphorites are clustered in the area of basales. Obviously, the source of phophorite's ore-forming materials is closely related with the geological processes at depth. REE patterns are characterized by a low content in total and a gradually increasing with the increasing of REE atomic number, and the NASC-normalized value ranging between the upper and the lower limits of typical hydrothermal deposits. The large scale uranium-polymetallic mineralization was controlled by the environment of continental margin rifting. The authors propose that thermal sedimentation or exhalation-sedimentation is the mechanism of the large scale uranium-polymetallic mineralization in the southeast continental margin of the Yangtze plate. (authors)

Geochronology of La Tinta Upper Proterozoic sedimentary rocks, Argentina

International Nuclear Information System (INIS)

Cingolani, C.A.; Bonhomme, M.G.

1982-01-01

Olavarria-Sierras Bayas, Barker-San Manuel and Balcarce-Mar del Plata fine-grained sedimentary rocks from La Tinta Formation, the pre-Cenozoic cover of the Tandilia region, were studied using the Rb-Sr and K-Ar geochronology. The mineralogical study of the fine fraction has shown that only the Olavarria-Sierras Bayas area presents suitable material comprising typical sedimentary clays, affected only by diagenetic processes. Two Rb-Sr isochrons were obtained from Olavarria-Sierras Bayas rocks. They show: (1) an age of 769 +- 12 Ma with ( 87 Sr/ 86 Sr) 0 = 0.7121 +- 0.0005, for Aust Quarry rocks; and (2) an age of 723 +- 21 Ma with ( 87 Sr/ 86 Sr) 0 = 0.7171 +- 0.0012 for Cerro Negro and Losa Quarries rocks. Considering the above-mentioned isochron data and the mineralogy of the clays studied, the conclusion is drawn that the ages obtained reflect the isotopic setting of a late diagenetic process, dated back to nearly 720 Ma. K-Ar data also support the Rb-Sr isochrons and the late diagenetic clay origin. The lower section of La Tinta sequence in the Sierras Bayas area must then be considered as Upper Proterozoic in age. These new data support the recently reported stratigraphical divisions and ages. (Auth.)

Intra-continental subduction and contemporaneous lateral extrusion of the upper plate: insights into Alps-Adria interactions

Science.gov (United States)

van Gelder, Inge; Willingshofer, Ernst; Sokoutis, Dimitrios; Cloetingh, Sierd

2017-04-01

A series of physical analogue experiments were performed to simulate intra-continental subduction contemporaneous with lateral extrusion of the upper plate to study the interferences between these two processes at crustal levels and in the lithospheric mantle. The lithospheric-scale models are specifically designed to represent the collision of the Adriatic microplate with the Eastern Alps, simulated by an intra-continental weak zone to initiate subduction and a weak confined margin perpendicular to the direction of convergence in order to allow for extrusion of the lithosphere. The weak confined margin is the analog for the opening of the Pannonian back-arc basin adjacent to the Eastern Alps with the direction of extension perpendicular to the strike of the orogen. The models show that intra-continental subduction and coeval lateral extrusion of the upper plate are compatible processes. The obtained deformation structures within the extruding region are similar compared to the classical setup where lateral extrusion is provoked by lithosphere-scale indentation. In the models a strong coupling across the subduction boundary allows for the transfer of abundant stresses to the upper plate, leading to laterally varying strain regimes that are characterized by crustal thickening near a confined margin and dominated by lateral displacement of material near a weak lateral confinement. During ongoing convergence the strain regimes propagate laterally, thereby creating an area of overlap characterized by transpression. In models with oblique subduction, with respect to the convergence direction, less deformation of the upper plate is observed and as a consequence the amount of lateral extrusion decreases. Additionally, strain is partitioned along the oblique plate boundary leading to less subduction in expense of right lateral displacement close to the weak lateral confinement. Both oblique and orthogonal subduction models have a strong resemblance to lateral extrusion

Geology of Paleozoic Rocks in the Upper Colorado River Basin in Arizona, Colorado, New Mexico, Utah, and Wyoming, Excluding the San Juan Basin

Science.gov (United States)

Geldon, Arthur L.

2003-01-01

The geology of the Paleozoic rocks in the Upper Colorado River Basin in Arizona, Colorado, New Mexico, Utah, and Wyoming, was studied as part of the U.S. Geological Survey's Regional Aquifer-System Analysis Program to provide support for hydrogeological interpretations. The study area is segmented by numerous uplifts and basins caused by folding and faulting that have recurred repeatedly from Precambrian to Cenozoic time. Paleozoic rocks in the study area are 0-18,000 feet thick. They are underlain by Precambrian igneous, metamorphic, and sedimentary rocks and are overlain in most of the area by Triassic formations composed mostly of shale. The overlying Mesozoic and Tertiary rocks are 0-27,000 feet thick. All Paleozoic systems except the Silurian are represented in the region. The Paleozoic rocks are divisible into 11 hydrogeologic units. The basal hydrogeologic unit consisting of Paleozoic rocks, the Flathead aquifer, predominantly is composed of Lower to Upper Cambrian sandstone and quartzite. The aquifer is 0-800 feet thick and is overlain gradationally to unconformably by formations of Cambrian to Mississippian age. The Gros Ventre confining unit consists of Middle to Upper Cambrian shale with subordinate carbonate rocks and sandstone. The confining unit is 0-1,100 feet thick and is overlain gradationally to unconformably by formations of Cambrian to Mississippian age. The Bighom aquifer consists of Middle Cambrian to Upper Ordovician limestone and dolomite with subordinate shale and sandstone. The aquifer is 0-3,000 feet thick and is overlain unconformably by Devonian and Mississipplan rocks. The Elbert-Parting confining unit consists of Lower Devonian to Lower Mississippian limestone, dolomite, sandstone, quartzite, shale, and anhydrite. It is 0-700 feet thick and is overlain conformably to unconformably by Upper Devonian and Mississippian rocks. The Madison aquifer consists of two zones of distinctly different lithology. The lower (Redwall-Leadville) zone

Spatial arrangement and size distribution of normal faults, Buckskin detachment upper plate, Western Arizona

Science.gov (United States)

Laubach, S. E.; Hundley, T. H.; Hooker, J. N.; Marrett, R. A.

2018-03-01

Fault arrays typically include a wide range of fault sizes and those faults may be randomly located, clustered together, or regularly or periodically located in a rock volume. Here, we investigate size distribution and spatial arrangement of normal faults using rigorous size-scaling methods and normalized correlation count (NCC). Outcrop data from Miocene sedimentary rocks in the immediate upper plate of the regional Buckskin detachment-low angle normal-fault, have differing patterns of spatial arrangement as a function of displacement (offset). Using lower size-thresholds of 1, 0.1, 0.01, and 0.001 m, displacements range over 5 orders of magnitude and have power-law frequency distributions spanning ∼ four orders of magnitude from less than 0.001 m to more than 100 m, with exponents of -0.6 and -0.9. The largest faults with >1 m displacement have a shallower size-distribution slope and regular spacing of about 20 m. In contrast, smaller faults have steep size-distribution slopes and irregular spacing, with NCC plateau patterns indicating imposed clustering. Cluster widths are 15 m for the 0.1-m threshold, 14 m for 0.01-m, and 1 m for 0.001-m displacement threshold faults. Results demonstrate normalized correlation count effectively characterizes the spatial arrangement patterns of these faults. Our example from a high-strain fault pattern above a detachment is compatible with size and spatial organization that was influenced primarily by boundary conditions such as fault shape, mechanical unit thickness and internal stratigraphy on a range of scales rather than purely by interaction among faults during their propagation.

Investigation of Rock Failure Pattern in Creep by Digital Speckle Correlation Method

Directory of Open Access Journals (Sweden)

Yunliang Tan

2013-01-01

Full Text Available In order to study the mechanical characteristics from creep deformation to failure of rock, the tests of uniaxial compression and pushing steel-plate anchored in rock were performed, by using RLJW-2000 servo test synchronizing with Digital Speckle Correlation Method (DSCM. The investigations showed that for a uniaxial compressive specimen, when load arrived at 0.5σc, displacement clusters orderly formed, which was ahead of the macrocreep strain occurring in a slight jump mode when load arrived at 0.7σc. When the load level arrived at 0.8σc, displacement clusters gathered to be a narrow band. After that, the specimen abruptly fractured in a shear mode. In the creep pushing steel-plate test, when pushing force arrived at 25 kN, crack began to occur, the horizontal displacement field as well as shear strain field concentrated continuously along the interface between steel-plate and rock, and a new narrow concentrating band gathered in the upper layer. When pushing force arrived at 27.5 kN, another new narrow shear deformation band formed in the lower layer. Then, the steel-plate was pushed out quickly accompanying strong creep deformation.

Folded fabric tunes rock deformation and failure mode in the upper crust.

Science.gov (United States)

Agliardi, F; Dobbs, M R; Zanchetta, S; Vinciguerra, S

2017-11-10

The micro-mechanisms of brittle failure affect the bulk mechanical behaviour and permeability of crustal rocks. In low-porosity crystalline rocks, these mechanisms are related to mineralogy and fabric anisotropy, while confining pressure, temperature and strain rates regulate the transition from brittle to ductile behaviour. However, the effects of folded anisotropic fabrics, widespread in orogenic settings, on the mechanical behaviour of crustal rocks are largely unknown. Here we explore the deformation and failure behaviour of a representative folded gneiss, by combining the results of triaxial deformation experiments carried out while monitoring microseismicity with microstructural and damage proxies analyses. We show that folded crystalline rocks in upper crustal conditions exhibit dramatic strength heterogeneity and contrasting failure modes at identical confining pressure and room temperature, depending on the geometrical relationships between stress and two different anisotropies associated to the folded rock fabric. These anisotropies modulate the competition among quartz- and mica-dominated microscopic damage processes, resulting in transitional brittle to semi-brittle modes under P and T much lower than expected. This has significant implications on scales relevant to seismicity, energy resources, engineering applications and geohazards.

Spirit Begins Drive Around Home Plate

Science.gov (United States)

2009-01-01

The hazard avoidance camera on the front of NASA's Mars Exploration Rover Spirit took this image after a drive by Spirit on the 1,829th Martian day, or sol, of Spirit's mission on the surface of Mars (Feb. 24, 2009). On Sol 1829, Spirit drove 6.29 meters (21 feet) northwestward, away from the northern edge of the low plateau called 'Home Plate.' The track dug by the dragged right-front wheel as the rover drove backward is visible in this image, receding toward the southeast. Rock layers of the northern slope of Home Plate are visible in the upper right portion of the image. In sols prior to 1829, the rover team had been trying to maneuver Spirit to climb onto the northern edge of Home Plate, ready to drive southward across the top of the plateau toward science destinations south of Home Plate. The Sol 1829 drive was the first move of a revised strategy to circle at least partway around Home Plate on the trek toward the sites south of the plateau.

Radiation shielding properties of some natural rocks in upper Egypt

International Nuclear Information System (INIS)

Abbady, A.; Ahmed, N.K.; Saied, M.H.; Uosif, M.A.; El-kamel, A.H.

1999-01-01

To support the use of some natural rocks in Upper Egypt as suitable radiation materials, the attenuation of gamma - ray through destructive and nondestructive samples of alabaster, marble and limestone have been tested in the energy range from 356 keV to 1173 keV. The attenuation coefficients of the nondestructive samples are found higher than the values of the destructive samples. The half - layer values for attenuation, and the concentration of uranium and thorium in the samples were calculated and discussed

Uncertainty evaluation in the self-alignment test of the upper plate of a press

International Nuclear Information System (INIS)

Lourenço, Alexandre S; E Sousa, J Alves

2015-01-01

This paper describes a method to evaluate uncertainty of the self-alignment test of the upper plate of a press according to EN 12390-4:2000. The method, the algorithms and the sources of uncertainty are described

Evolution characteristic of gypsum-salt rocks of the upper member of Oligocene Lower Ganchaigou Fm in the Shizigou area, western Qaidam Basin

Directory of Open Access Journals (Sweden)

Dinghong Yi

2017-09-01

Full Text Available Over years of oil and gas exploration in the Qaidam Basin, reservoirs have been discovered in many layers. In the Shizigou area, western Qaidam Basin, the upper member of Oligocene Lower Ganchaigou Fm is an important target for oil and gas exploration, and gypsum-salt rocks are the high-quality caprocks for the preservation of oil and gas reservoirs in this area. For predicting oil and gas exploration direction and target in the western Qaidam Basin and providing guidance for its oil and gas exploration deployment, its depositional characteristics and environment of gypsum-salt rocks in this area were investigated based on the core observation, thin section identification, and analysis of grain size, sensitivity parameter ratios (Sr/Cu, Fe/Mn, (Fe + Al/(Ca + Mg, V/(V + Ni and Pr/Ph, pyrite content and inclusions. The following characteristics are identified. First, gypsum-salt rocks are mainly distributed in the depocenter of the lake basin and their thickness decreases towards the margin of the basin. They are laterally transformed into carbonate rocks or terrigenous clastic rocks. They are areally distributed in the shape of irregular ellipse. Second, gypsum-salt rocks are vertically developed mainly in the middle and upper parts of the upper member of Lower Ganchaigou Fm and they are interbedded with carbonate rocks or terrigenous clastic rocks. Their single layer thickness changes greatly, and there are many layers with good continuity. Third, Sand Group III to Group I in the upper member of Lower Ganchaigou Fm (inter-salt are of reductive water environment of semi-deep to deep lake facies due to their sedimentation in an arid and hot climate. It is concluded that gypsum-salt rocks of the upper member of Lower Ganchaigou Fm are distributed widely with great accumulative thickness in this area; and that they are originated from deep lake water by virtue of evaporation, concentration and crystallization in an arid and hot climate instead

Continental lithosphere of the Arabian Plate: A geologic, petrologic, and geophysical synthesis

Science.gov (United States)

Stern, Robert J.; Johnson, Peter

2010-07-01

The Arabian Plate originated ˜ 25 Ma ago by rifting of NE Africa to form the Gulf of Aden and Red Sea. It is one of the smaller and younger of the Earth's lithospheric plates. The upper part of its crust consists of crystalline Precambrian basement, Phanerozoic sedimentary cover as much as 10 km thick, and Cenozoic flood basalt (harrat). The distribution of these rocks and variations in elevation across the Plate cause a pronounced geologic and topographic asymmetry, with extensive basement exposures (the Arabian Shield) and elevations of as much as 3000 m in the west, and a Phanerozoic succession (Arabian Platform) that thickens, and a surface that descends to sea level, eastward between the Shield and the northeastern margin of the Plate. This tilt in the Plate is partly the result of marginal uplift during rifting in the south and west, and loading during collision with, and subduction beneath, the Eurasian Plate in the northeast. But a variety of evidence suggests that the asymmetry also reflects a fundamental crustal and mantle heterogeneity in the Plate that dates from Neoproterozoic time when the crust formed. The bulk of the Plate's upper crystalline crust is Neoproterozoic in age (1000-540 Ma) reflecting, in the west, a 300-million year process of continental crustal growth between ˜ 850 and 550 Ma represented by amalgamated juvenile magmatic arcs, post-amalgamation sedimentary and volcanic basins, and granitoid intrusions that make up as much as 50% of the Shield's surface. Locally, Archean and Paleoproterozoic rocks are structurally intercalated with the juvenile Neoproterozoic rocks in the southern and eastern parts of the Shield. The geologic dataset for the age, composition, and origin of the upper crust of the Plate in the east is smaller than the database for the Shield, and conclusions made about the crust in the east are correspondingly less definitive. In the absence of exposures, furthermore, nothing is known by direct observation about the

Uranium and thorium occurrences in Precambrian rocks, Upper Peninsula of Michigan and northern Wisconsin, with thoughts on other possible settings

International Nuclear Information System (INIS)

Kalliokoski, J.

1976-01-01

The following areas are covered: Precambrian geology of northern Michigan; mode of occurrence of uranium and thorium in the Precambrian rocks of the Upper Peninsula of Michigan; selected stratigraphic relationships, Precambrian rocks of Michigan; mode of occurrence of uranium and thorium in Precambrian rocks of Wisconsin; and background data for geochemical exploration

Ship Grounding on Rock - I. Theory

DEFF Research Database (Denmark)

Simonsen, Bo Cerup

1997-01-01

and transverse frames, floors and bulkheads. The expressions are derived by use of an energy method or a type of 'upper bound' method which rigorously takes into account the effects of large plastic deformations, friction and fracture. A high level of generality for the methodology has been obtained...... by postulating a global mode of deformation for the structure around the rock with one free parameter, the plate split angle, related to the shape of thedeformation mode. It is assumed that intersections between structural components stay intact during the entire deformation process so the resistance...

Upper-Mantel Earthquakes in the Australia-Pacific Plate Boundary Zone and the Roots of the Alpine Fault

Science.gov (United States)

Boese, C. M.; Warren-Smith, E.; Townend, J.; Stern, T. A.; Lamb, S. H.

2016-12-01

Seismicity in the upper mantle in continental collision zones is relatively rare, but observed around the world. Temporary seismometer deployments have repeatedly detected mantle earthquakes at depths of 40-100 km within the Australia-Pacific plate boundary zone beneath the South Island of New Zealand. Here, the transpressive Alpine Fault constitutes the primary plate boundary structure linking subduction zones of opposite polarity farther north and south. The Southern Alps Microearthquake Borehole Array (SAMBA) has been operating continuously since November 2008 along a 50 km-long section of the central Alpine Fault, where the rate of uplift of the Southern Alps is highest. To date it has detected more than 40 small to moderate-sized mantle events (1≤ML≤3.9). The Central Otago Seismic Array (COSA) has been in operation since late 2012 and detected 15 upper mantle events along the sub-vertical southern Alpine Fault. Various mechanisms have been proposed to explain the occurrence of upper mantle seismicity in the South Island, including intra-continental subduction (Reyners 1987, Geology); high shear-strain gradients due to depressed geotherms and viscous deformation of mantle lithosphere (Kohler and Eberhart-Phillips 2003, BSSA); high strain rates resulting from plate bending (Boese et al. 2013, EPSL), and underthrusting of the Australian plate (Lamb et al. 2015, G3). Focal mechanism analysis reveals a variety of mechanisms for the upper mantle events but predominantly strike-slip and reverse faulting. In this study, we apply spectral analysis to better constrain source parameters for these mantle events. These results are interpreted in conjunction with new information about crustal structure and low-frequency earthquakes near the Moho and in light of existing velocity, attenuation and resistivity models.

Determination of Rock Mass Modulus Using the Plate Loading Method at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Finley, R.E.; George, J.T.; Riggins, M.

1999-01-01

A suite of plate loading tests has recently been conducted by Sandia National Laboratories at the Exploratory Studies Facility at Yucca Mountain, Nevada. Fielding of these in situ tests as well as other approaches undertaken for the determination of rock mass modulus are described. The various methodologies are evaluated and their data compared. Calculation by existing empirical methods and numerical modeling are compared to each other as well as to field data

Geotechnical characteristics and stability analysis of rock-soil aggregate slope at the Gushui Hydropower Station, southwest China.

Science.gov (United States)

Zhou, Jia-wen; Shi, Chong; Xu, Fu-gang

2013-01-01

Two important features of the high slopes at Gushui Hydropower Station are layered accumulations (rock-soil aggregate) and multilevel toppling failures of plate rock masses; the Gendakan slope is selected for case study in this paper. Geological processes of the layered accumulation of rock and soil particles are carried out by the movement of water flow; the main reasons for the toppling failure of plate rock masses are the increasing weight of the upper rock-soil aggregate and mountain erosion by river water. Indoor triaxial compression test results show that, the cohesion and friction angle of the rock-soil aggregate decreased with the increasing water content; the cohesion and the friction angle for natural rock-soil aggregate are 57.7 kPa and 31.3° and 26.1 kPa and 29.1° for saturated rock-soil aggregate, respectively. The deformation and failure mechanism of the rock-soil aggregate slope is a progressive process, and local landslides will occur step by step. Three-dimensional limit equilibrium analysis results show that the minimum safety factor of Gendakan slope is 0.953 when the rock-soil aggregate is saturated, and small scale of landslide will happen at the lower slope.

Microstructural evolution and seismic anisotropy of upper mantle rocks in rift zones. Geologica Ultraiectina (300)

NARCIS (Netherlands)

Palasse, L.N.

2008-01-01

This thesis investigates field-scale fragments of subcontinental upper mantle rocks from the ancient Mesozoic North Pyrenean rift and Plio-Pleistocene xenoliths from the active Baja California rift, in order to constrain the deformation history of the uppermost mantle. The main focus of the study is

Uranium occurrences in the volcanic rocks of Upper Mahakam, east Kalimantan

International Nuclear Information System (INIS)

Djokolelono, S.; Agoes, E.

1988-01-01

The Kawat area, which is about 35 km 2 in size, is located in the Upper Mahakam region and is one of the areas being prospected in Kalimantan. It has already been covered by general, detailed and systematic prospection. The Kawat area formed a tectonical depression and was intercepted by the volcanic products of various episodes. The regional stratigraphy of this area, from the bottom upwards, is as follows: Unit 1: quartzite and ophiolitic green rock; Unit 2: black shale, sometimes with boulders of quartzite and radiolarite; Unit 3: massive conglomeratic sandstone, alternating with claystone and sandstone sequences; Unit 4: sandstone, siltstone and claystone, with an intercalation of volcanic rocks. Uraniferous occurrences are reflected by anomalous zones located in the volcanic facies of Unit 4, usually in aphanitic rhyolite. Mineralization consists of pitchblende associated with molybdenite and pyrite. Although the Kawat area is very remote, future development is of great interest. (author). 4 figs

Geochemistry of the Oruatemanu Formation, Arrow Rocks, Northland, New Zealand

International Nuclear Information System (INIS)

Hori, R.S.; Higuchi, Y.; Fujiki, T.; Maeda, T.; Ikehara, M.

2007-01-01

We investigated the geochemical characteristics of sedimentary rocks from the Upper Permian - Middle Triassic Oruatemanu Formation on Arrow Rocks, Waipapa Terrane, New Zealand. The sedimentary rocks consist of limestone, tuffaceous shale, vari-coloured bedded chert, hemipelagic shale and green siliceous mudstone (= green argillite), in ascending order, a typical oceanic plate sequence. Shale and green argillite have higher Zr/Nb ratios than do chert and tuffaceous shales, and show similar REE patterns to PAAS (Post-Archean average Australian shale). In contrast, chert sequences from the basal part and intercalated tuff layers have high TiO 2 contents and Zr/Nb ratios similar to those of basaltic rocks from Arrow Rocks. These geochemical characteristics suggest that the sedimentary environment of the Oruatemanu Formation changed upward, from an open sea setting to the continental margin of Gondwanaland. Chemical compositions of bedded cherts from Arrow Rocks indicate a mixing of biogenic silica, detritus from continents and basaltic materials. In the interval from Upper Permian to Lower Middle Triassic this mixing shows remarkable secular variations. We detected geochemical signals of two Oceanic Anoxic Events (OAEs), one at the Permian/Triassic (P/T) boundary, and the other at the middle Upper Induan level. We name them the OAEα (P/T OAE) and OAEβ (Upper Induan OAE). These OAE horizons are enriched in S, U and other heavy metals (e.g. Mo and Cr), and also have high V/(V+Ni) ratios. Based on a comparison between enrichment factors of Cr and other redox-sensitive trace elements (e.g. Zn, Pb, Co, Cu), the Upper Induan OAEβ is considered to be more intense than the P/T boundary OAEα. This result is not in agreement with the superanoxia model previously proposed. In addition, OAEβ corresponds well with the radiolarian faunal turnover from Permian to Triassic forms documented from the Oruatemanu Formation in this volume. These results may suggest that peak time and

Extreme hydrothermal conditions at an active plate-bounding fault

Science.gov (United States)

Sutherland, Rupert; Townend, John; Toy, Virginia; Upton, Phaedra; Coussens, Jamie; Allen, Michael; Baratin, Laura-May; Barth, Nicolas; Becroft, Leeza; Boese, Carolin; Boles, Austin; Boulton, Carolyn; Broderick, Neil G. R.; Janku-Capova, Lucie; Carpenter, Brett M.; Célérier, Bernard; Chamberlain, Calum; Cooper, Alan; Coutts, Ashley; Cox, Simon; Craw, Lisa; Doan, Mai-Linh; Eccles, Jennifer; Faulkner, Dan; Grieve, Jason; Grochowski, Julia; Gulley, Anton; Hartog, Arthur; Howarth, Jamie; Jacobs, Katrina; Jeppson, Tamara; Kato, Naoki; Keys, Steven; Kirilova, Martina; Kometani, Yusuke; Langridge, Rob; Lin, Weiren; Little, Timothy; Lukacs, Adrienn; Mallyon, Deirdre; Mariani, Elisabetta; Massiot, Cécile; Mathewson, Loren; Melosh, Ben; Menzies, Catriona; Moore, Jo; Morales, Luiz; Morgan, Chance; Mori, Hiroshi; Niemeijer, Andre; Nishikawa, Osamu; Prior, David; Sauer, Katrina; Savage, Martha; Schleicher, Anja; Schmitt, Douglas R.; Shigematsu, Norio; Taylor-Offord, Sam; Teagle, Damon; Tobin, Harold; Valdez, Robert; Weaver, Konrad; Wiersberg, Thomas; Williams, Jack; Woodman, Nick; Zimmer, Martin

2017-06-01

Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes. Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre. At temperatures above 300-450 degrees Celsius, usually found at depths greater than 10-15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional-mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades. The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults.

Extreme hydrothermal conditions at an active plate-bounding fault.

Science.gov (United States)

Sutherland, Rupert; Townend, John; Toy, Virginia; Upton, Phaedra; Coussens, Jamie; Allen, Michael; Baratin, Laura-May; Barth, Nicolas; Becroft, Leeza; Boese, Carolin; Boles, Austin; Boulton, Carolyn; Broderick, Neil G R; Janku-Capova, Lucie; Carpenter, Brett M; Célérier, Bernard; Chamberlain, Calum; Cooper, Alan; Coutts, Ashley; Cox, Simon; Craw, Lisa; Doan, Mai-Linh; Eccles, Jennifer; Faulkner, Dan; Grieve, Jason; Grochowski, Julia; Gulley, Anton; Hartog, Arthur; Howarth, Jamie; Jacobs, Katrina; Jeppson, Tamara; Kato, Naoki; Keys, Steven; Kirilova, Martina; Kometani, Yusuke; Langridge, Rob; Lin, Weiren; Little, Timothy; Lukacs, Adrienn; Mallyon, Deirdre; Mariani, Elisabetta; Massiot, Cécile; Mathewson, Loren; Melosh, Ben; Menzies, Catriona; Moore, Jo; Morales, Luiz; Morgan, Chance; Mori, Hiroshi; Niemeijer, Andre; Nishikawa, Osamu; Prior, David; Sauer, Katrina; Savage, Martha; Schleicher, Anja; Schmitt, Douglas R; Shigematsu, Norio; Taylor-Offord, Sam; Teagle, Damon; Tobin, Harold; Valdez, Robert; Weaver, Konrad; Wiersberg, Thomas; Williams, Jack; Woodman, Nick; Zimmer, Martin

2017-06-01

Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes. Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre. At temperatures above 300-450 degrees Celsius, usually found at depths greater than 10-15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional-mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades. The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults.

The Lagrangian Multiplier Method of Finding Upper and Lower Limits to Critical Stresses of Clamped Plates

Science.gov (United States)

1946-01-01

geometrica ~ boundary condi- tions of the problem. (2) The energy of the load-plate system is computed for this deflection surface and is then minimized...and interpolating to find the k that makes the seriw vanish. The correct value of m is that which gives the lowest value of k. For two half waves (m=2...the square plate, the present rekdively simple upper- and lower-limit calcula- tions show that his est,imatd limit of error is correct for this case

Plate-Tectonic Circulation is Driven by Cooling From the Top and is Closed Within the Upper Mantle

Science.gov (United States)

Hamilton, W. B.

2001-12-01

Subduction drives plate tectonics and is due to cooling from the top: circulation is self-organized, and likely is closed above the discontinuity near 660 km. The contrary consensus that plate tectonics is driven by bottom heating and involves the entire mantle combines misunderstood kinematics with flawed concepts of through-the-mantle plumes and subduction. Plume conjecture came from the Emperor-Hawaii progression, the 45 Ma inflection in which was assumed to mark a 60-degree change in direction of that part of the Pacific plate over a fixed plume. Smooth spreading patterns around the east and south margin of the Pacific plate, and paleomagnetic data, disprove such a change. Speculations that plumes move, jump, etc. do not revive falsified conjecture. Geochemical distinctions between enriched island and depleted ridge basalts (which overlap) are expected products of normal upper-mantle processes, not plumes. MORB traverses solidus-T asthenosphere, whereas OIB zone-refines through subsolidus lithosphere and crust, crystallizing refractories to retain T of diminishing melt while assimilating and retaining fusibles. Tomographic inference of deep-mantle subduction is presented misleadingly and may reflect methodological and sampling artifacts (downward smearing, and concentration of recorded body waves in bundles within broad anomalies otherwise poorly sampled). Planetological and other data require hot Earth accretion, and thorough early fractionation, from material much more refractory than primitive meteorites, and are incompatible with the little-fractionated lower mantle postulated to permit whole-mantle circulation. The profound seismic discontinuity near 660 km is a thermodynamic and physical barrier to easy mass transfer in either direction. Refractory lower mantle convects slowly, perhaps in layers, and loses primarily original heat, whereas upper mantle churns rapidly, and the 660 decoupling boundary must have evolved into a compositional barrier also

Subduction history of the Paleo-Pacific plate beneath the Eurasian continent: Evidence from Mesozoic igneous rocks and accretionary complex in NE Asia

Science.gov (United States)

Xu, W.

2015-12-01

Mesozoic magmatisms in NE China can be subdivided into seven stages, i.e., Late Triassic, Early Jurassic, Middle Jurassic, Late Jurassic, early Early Cretaceous, late Early Cretaceous, and Late Cretaceous. Late Triassic magmatisms consist of calc-alkaline igneous rocks in the Erguna Massif, and bimodal igneous rocks in eastern margin of Eurasian continent. The former reveals southward subduction of the Mongol-Okhotsk oceanic plate, the latter reveals an extensional environment (Xu et al., 2013). Early Jurassic magmatisms are composed of calc-alkaline igneous rocks in the eastern margin of the Eurasian continent and the Erguna Massif, revealing westward subduction of the Paleo-pacific plate and southward subduction of the Mongol-Okhotsk oceanic plate (Tang et al., 2015), respectively. Middle Jurassic magmatism only occur in the Great Xing'an Range and the northern margin of the NCC, and consists of adakitic rocks that formed in crustal thickening, reflecting the closure of the Mongol-Okhotsk ocean (Li et al., 2015). Late Jurassic and early Early Cretaceous magmatisms only occur to the west of the Songliao Basin, and consist of trackyandesite and A-type of rhyolites, revealing an extensional environment related to delamination of thickened crust. The late Early Cretaceous magmatisms are widespread in NE China, and consist of calc-alkaline volcanics in eastern margin and bimodal volcanics in intracontinent, revealing westward subduction of the Paleo-pacific plate. Late Cretaceous magmatisms mainly occur to the east of the Songliao Basin, and consist of calc-alkaline volcanics in eastern margin and alkaline basalts in intracontinent (Xu et al., 2013), revealing westward subduction of the Paleo-pacific plate. The Heilongjiang complex with Early Jurassic deformation, together with Jurassic Khabarovsk complex in Russia Far East and Mino-Tamba complex in Japan, reveal Early Jurassic accretionary history. Additionally, the Raohe complex with the age of ca. 169 Ma was

PWR integral tie plate and locking mechanism

International Nuclear Information System (INIS)

Flora, B.S.; Osborne, J.L.

1980-01-01

A locking mechanism for securing an upper tie plate to the tie rods of a nuclear fuel bundle is described. The mechanism includes an upper tie plate assembly and locking sleeves fixed to the ends of the tie rods. The tie plate is part of the upper tie plate assembly and is secured to the fuel bundle by securing the entire upper tie plate assembly to the locking sleeves fixed to the tie rods. The assembly includes, in addition to the tie plate, locking nuts for engaging the locking sleeves, retaining sleeves to operably connect the locking nuts to the assembly, a spring biased reaction plate to restrain the locking nuts in the locked position and a means to facilitate the removal of the entire assembly as a unit from the fuel bundle

Source and fractionation controls on subduction-related plutons and dike swarms in southern Patagonia (Torres del Paine area) and the low Nb/Ta of upper crustal igneous rocks

Science.gov (United States)

Müntener, Othmar; Ewing, Tanya; Baumgartner, Lukas P.; Manzini, Mélina; Roux, Thibaud; Pellaud, Pierre; Allemann, Luc

2018-05-01

The subduction system in southern Patagonia provides direct evidence for the variability of the position of an active continental arc with respect to the subducting plate through time, but the consequences on the arc magmatic record are less well studied. Here we present a geochemical and geochronological study on small plutons and dykes from the upper crust of the southern Patagonian Andes at 51°S, which formed as a result of the subduction of the Nazca and Antarctic plates beneath the South American continent. In situ U-Pb geochronology on zircons and bulk rock geochemical data of plutonic and dyke rocks are used to constrain the magmatic evolution of the retro-arc over the last 30 Ma. We demonstrate that these combined U-Pb and geochemical data for magmatic rocks track the temporal and spatial migration of the active arc, and associated retro-arc magmatism. Our dataset indicates that the rear-arc area is characterized by small volumes of alkaline basaltic magmas at 29-30 Ma that are characterized by low La/Nb and Th/Nb ratios with negligible arc signatures. Subsequent progressive eastward migration of the active arc culminated with the emplacement of calc-alkaline plutons and dikes 17-16 Ma with elevated La/Nb and Th/Nb ratios and typical subduction signatures constraining the easternmost position of the southern Patagonian batholith at that time. Geochemical data on the post-16 Ma igneous rocks including the Torres del Paine laccolith indicate an evolution to transitional K-rich calc-alkaline magmatism at 12.5 ± 0.2 Ma. We show that trace element ratios such as Nb/Ta and Dy/Yb systematically decrease with increasing SiO2, for both the 17-16 Ma calc-alkaline and the 12-13 Ma K-rich transitional magmatism. In contrast, Th/Nb and La/Nb monitor the changes in the source composition of these magmas. We suggest that the transition from the common calc-alkaline to K-rich transitional magmatism involves a change in the source component, while the trace element ratios

Metamorphic rocks in the deep boreholes near Maribor

Directory of Open Access Journals (Sweden)

Mirka Trajanova

2002-12-01

Full Text Available Six research-captive boreholes for thermal water passed through a pile of metamorphic rocks near Maribor (Eastern Slovenia that is on average about 1000 m thick. The succession of metamorphic rocks is characteristic for the Pohorje Mt. and eastern Kobansko region. In the area of the boreholes two tectonic zones are more pronounced: the upper one, at a depth of about 510 to 550 m at the contact of the Štelenska Gora and Phyllite formations and the deeper one at a depth of about 460 to 590 m, indicating the reverse fault junction of the Phyllite and Kobansko formations. They belong to the second andthe third thrust unit of the accretionary wedge formed at the collision of the European and African plates. Four Alpine nappe units are proven in the Slovenian part of the Eastern Alps.

Thermo-mechanical Properties of Upper Jurassic (Malm) Carbonate Rock Under Drained Conditions

Science.gov (United States)

Pei, Liang; Blöcher, Guido; Milsch, Harald; Zimmermann, Günter; Sass, Ingo; Huenges, Ernst

2018-01-01

The present study aims to quantify the thermo-mechanical properties of Neuburger Bankkalk limestone, an outcrop analog of the Upper Jurassic carbonate formation (Germany), and to provide a reference for reservoir rock deformation within future enhanced geothermal systems located in the Southern German Molasse Basin. Experiments deriving the drained bulk compressibility C were performed by cycling confining pressure p c between 2 and 50 MPa at a constant pore pressure p p of 0.5 MPa after heating the samples to defined temperatures between 30 and 90 °C. Creep strain was then measured after each loading and unloading stage, and permeability k was obtained after each creep strain measurement. The drained bulk compressibility increased with increasing temperature and decreased with increasing differential pressure p d = p c - p p showing hysteresis between the loading and unloading stages above 30 °C. The apparent values of the indirectly calculated Biot coefficient α ind containing contributions from inelastic deformation displayed the same temperature and pressure dependencies. The permeability k increased immediately after heating and the creep rates were also temperature dependent. It is inferred that the alteration of the void space caused by temperature changes leads to the variation of rock properties measured under isothermal conditions while the load cycles applied under isothermal conditions yield additional changes in pore space microstructure. The experimental results were applied to a geothermal fluid production scenario to constrain drawdown and time-dependent effects on the reservoir, overall, to provide a reference for the hydromechanical behavior of geothermal systems in carbonate, and more specifically, in Upper Jurassic lithologies.

Upper-plate splay fault earthquakes along the Arakan subduction belt recorded by uplifted coral microatolls on northern Ramree Island, western Myanmar (Burma)

Science.gov (United States)

Shyu, J. Bruce H.; Wang, Chung-Che; Wang, Yu; Shen, Chuan-Chou; Chiang, Hong-Wei; Liu, Sze-Chieh; Min, Soe; Aung, Lin Thu; Than, Oo; Tun, Soe Thura

2018-02-01

Upper-plate structures that splay out from the megathrusts are common features along major convergent plate boundaries. However, their earthquake and tsunami hazard potentials have not yet received significant attention. In this study, we identified at least one earthquake event that may have been produced by an upper-plate splay fault offshore western Myanmar, based on U-Th ages of uplifted coral microatolls. This event is likely an earthquake that was documented historically in C.E. 1848, with an estimated magnitude between 6.8 and 7.2 based on regional structural characteristics. Such magnitude is consistent with the observed co-seismic uplift amount of ∼0.5 m. Although these events are smaller in magnitude than events produced by megathrusts, they may produce higher earthquake and tsunami hazards for local coastal communities due to their proximity. Our results also indicate that earthquake events with co-seismic uplift along the coast may not necessarily produce a flight of marine terraces. Therefore, using only records of uplifted marine terraces as megathrust earthquake proxies may overlook the importance of upper-plate splay fault ruptures, and underestimate the overall earthquake frequency for future seismic and tsunami hazards along major subduction zones of the world.

Uranium favorability of tertiary sedimentary rocks of the western Okanogan highlands and of the upper Columbia River valley, Washington

International Nuclear Information System (INIS)

Marjaniemi, D.K.; Robins, J.W.

1975-08-01

Tertiary sedimentary rocks in the northern portions of the western Okanogan highlands and in the upper Columbia River valley were investigated during a regional study to determine the favorability for potential uranium resources of the Tertiary sedimentary rocks of northeastern Washington. This project involved measurement and sampling of surface sections, collection of samples from isolated outcrops, and chemical and mineralogical analyses of samples. No portion of the project area of this report is rated of high or of medium favorability for potential uranium resources. Low favorability ratings are given to Oroville, Tonasket, and Pine Creek areas of the Okanogan River valley; to the Republic graben; and to the William Lakes, Colville, and Sheep Creek areas of the upper Columbia River valley. All these areas contain some fluvial, poorly sorted feldspathic or arkosic sandstones and conglomerates. These rocks are characterized by very low permeability and a consistently high siliceous matrix suggesting very low initial permeability. There are no known uranium deposits in any of these areas, and low level uranium anomalies are rare

Strength and Deformation Rate of Plate Boundaries: The Rheological Effects of Grain Size Reduction, Structure, and Serpentinization.

Science.gov (United States)

Montesi, L.; Gueydan, F.

2016-12-01

Global strain rate maps reveal 1000-fold contrasts between plate interiors, oceanic or continental diffuse plate boundaries and narrow plate boundaries. Here, we show that rheological models based on the concepts of shear zone localization and the evolution of rock structure upon strain can explain these strain rate contrasts. Ductile shear zones constitute a mechanical paradox in the lithosphere. As every plastic deformation mechanism is strain-rate-hardening, ductile rocks are expected to deform at low strain rate and low stress (broad zone of deformation). Localized ductile shear zones require either a localized forcing (locally high stress) or a thermal or structural anomaly in the shear zone; either can be inherited or develop progressively as rocks deform. We previously identified the most effective process at each depth level of the lithosphere. In the upper crust and middle crust, rocks fabric controls localization. Grain size reduction is the most efficient mechanism in the uppermost mantle. This analysis can be generalized to consider a complete lithospheric section. We assume strain rate does not vary with depth and that the depth-integrated strength of the lithospheric does not change over time, as the total force is controlled by external process such as mantle convection and plate and slab buoyancy. Reducing grain size from a coarse value typical of undeformed peridotite to a value in agreement with the stress level (piezometer) while letting that stress vary from depth to depth (the integrated stress remains the same) increases the lithospheric strain rate by about a factor of 1000. This can explain the development of diffuse plate boundaries. The slightly higher strain rate of continental plate boundary may reflect development of a layered rock fabric in the middle crust. Narrow plate boundaries require additional weakening process. The high heat flux near mid-ocean ridge implies a thin lithosphere, which enhances stress (for constant integrated

Organic geochemical characterization of potential hydrocarbon source rocks in the upper Benue Trough

International Nuclear Information System (INIS)

Obaje, N. G.; Pearson, M. J.; Suh, C. E.; Dada, S. S.

1999-01-01

The Upper Benue Trough of Nigeria is the northeastern most portion of the Benue rift structure that extends from the northern limit of the Niger Delta in the south to the southern limit of the Chad basin int he northeast. this portion of the trough is made up of two arms: the Gongola Arm and the Yola Arm. Stratigraphic sequence in the Gongola Arm comprises the continental Albian Bima Sandstone, the transitional Cenomanian Yolde Formation and the marine Turonian - Santonian Gongila, Pindiga, and Fika Formations. Overlying these are the continental Campane - Maastrichtian Gombe Sandstone and the Tertiary Kerri - Kerri Formation. In the Yola Arm, the Turonian - Santonian sequence is replaced by the equally marine Dukul, Jessu, Sekuliye Formations, Numanha Shale, and the Lamja Sandstone. Organic geochemical studies have been carried on outcrop sample form the Gongila, Pindiga, Dukul Formations, the Fika shale and the shaly units of the Gombe Sandstone, with the aim of assessing their source rock potential. Gas Chromatography (GC), Gas Chromatography - Mass Spectrometry (C - MS), and Rock Eval Pyrolysis were the major organic geochemical tools employed. Biomaker hydrocarbon signatures obtained from the GC - MS and the Rock Eval Pyrolysis results indicate that all he formations studied, except the Dukul formation, are immature and are all lean in organic matter

Rock mechanics observations pertinent to the rheology of the continental lithosphere and the localization of strain along shear zones

Science.gov (United States)

Kirby, S.H.

1985-01-01

Emphasized in this paper are the deformation processes and rheologies of rocks at high temperatures and high effective pressures, conditions that are presumably appropriate to the lower crust and upper mantle in continental collision zones. Much recent progress has been made in understanding the flexure of the oceanic lithosphere using rock-mechanics-based yield criteria for the inelastic deformations at the top and base. At mid-plate depths, stresses are likely to be supported elastically because bending strains and elastic stresses are low. The collisional tectonic regime, however, is far more complex because very large permanent strains are sustained at mid-plate depths and this requires us to include the broad transition between brittle and ductile flow. Moreover, important changes in the ductile flow mechanisms occur at the intermediate temperatures found at mid-plate depths. Two specific contributions of laboratory rock rheology research are considered in this paper. First, the high-temperature steady-state flow mechanisms and rheology of mafic and ultramafic rocks are reviewed with special emphasis on olivine and crystalline rocks. Rock strength decreases very markedly with increases in temperature and it is the onset of flow by high temperature ductile mechanisms that defines the base of the lithosphere. The thickness of the continental lithosphere can therefore be defined by the depth to a particular isotherm Tc above which (at geologic strain rates) the high-temperature ductile strength falls below some arbitrary strength isobar (e.g., 100 MPa). For olivine Tc is about 700??-800??C but for other crustal silicates, Tc may be as low as 400??-600??C, suggesting that substantial decoupling may take place within thick continental crust and that strength may increase with depth at the Moho, as suggested by a number of workers on independent grounds. Put another way, the Moho is a rheological discontinuity. A second class of laboratory observations pertains to

Crustal and upper mantle investigations of the Caribbean-South American plate boundary

Science.gov (United States)

Bezada, Maximiliano J.

The evolution of the Caribbean --- South America plate boundary has been a matter of vigorous debate for decades and many questions remain unresolved. In this work, and in the framework of the BOLIVAR project, we shed light on some aspects of the present state and the tectonic history of the margin by using different types of geophysical data sets and techniques. An analysis of controlled-source traveltime data collected along a boundary-normal profile at ˜65°W was used to build a 2D P-wave velocity model. The model shows that the Caribbean Large Igenous Province is present offshore eastern Venezuela and confirms the uniformity of the velocity structure along the Leeward Antilles volcanic belt. In contrast with neighboring profiles, at this longitude we see no change in velocity structure or crustal thickness across the San Sebastian - El Pilar fault system. A 2D gravity modeling methodology that uses seismically derived initial density models was developed as part of this research. The application of this new method to four of the BOLIVAR boundary-normal profiles suggests that the uppermost mantle is denser under the South American continental crust and the island arc terranes than under the Caribbean oceanic crust. Crustal rocks of the island arc and extended island arc terranes of the Leeward Antilles have a relatively low density, given their P-wave velocity. This may be caused by low iron content, relative to average magmatic arc rocks. Finally, an analysis of teleseismic traveltimes with frequency-dependent kernels produced a 3D P-wave velocity perturbation model. The model shows the structure of the mantle lithosphere under the study area and clearly images the subduction of the Atlantic slab and associated partial removal of the lower lithosphere under northern South America. We also image the subduction of a section of the Caribbean plate under South America with an east-southeast direction. Both the Atlantic and Caribbean subducting slabs penetrate the

Absolute Plate Motion Control Since the Triassic from the Cocos Slab and its Associated Subduction Record in Mexico

Science.gov (United States)

Boschman, L.; Van Hinsbergen, D. J. J.; Langereis, C. G.; Molina-Garza, R. S.; Kimbrough, D. L.; Spakman, W.

2017-12-01

A positive wave speed anomaly interpreted as the Cocos slab stretches from the uppermost mantle at the Middle America trench in the west, to the lowermost mantle below the Atlantic in the east. The length and continuity of this slab indicates long-lived, uninterrupted eastward subduction of the attached Cocos Plate and its predecessor, the Farallon Plate. The geological record of Mexico contains Triassic to present day evidence of subduction, of which the post-Late Cretaceous phase is of continental margin-style. Interpretations of the pre-Upper Cretaceous subduction-related rock assemblages are under debate, and vary from far-travelled exotic intra-oceanic island arc character to in-situ extended continental margin origin. We present new paleomagnetic data that show that Triassic, Jurassic and Cretaceous subduction-related rocks from the Vizcaíno Peninsula and the Guerrero terrane have a paleolatitudinal plate motion history that is equal to that of the North American continent. This suggests that these rock assemblages were part of the overriding plate and were perhaps only separated from the North American continent by temporal fore- or back-arc spreading. The entire Triassic-present day subduction record, and hence, reconstructed trench location, can therefore be linked to the Cocos slab, which provides control on longitudinal plate motion of North America since the time of Pangea. Compared to the latest state of the art mantle frames, in which longitudes are essentially unconstrained for pre-Cretaceous times, our reconstructed absolute position of North America requires a significant westward longitudinal shift for Mesozoic times.

The Rock Art of Upper Tibet and Ladakh: Inner Asian cultural adaptation, regional differentiation and the Western Tibetan Plateau Style

OpenAIRE

Bruneau , Laurianne; Bellezza , John V.

2013-01-01

International audience; This paper examines common thematic and esthetic features discernable in the rock art of the western portion of the Tibetan plateau. This rock art is international in scope; it includes Ladakh (La-dwags) (under Indian jurisdiction), Tö (Stod) and the Changthang (Byang-thang) (under Chinese administration) hereinafter called Upper Tibet. This work sets out the relationship of this art to other regions of Inner Asia and defines what we call the 'Western Tibetan Plateau S...

Reconstruction of large upper eyelid defects with a free tarsal plate graft and a myocutaneous pedicle flap plus a free skin graft.

Science.gov (United States)

Toft, Peter B

2016-01-01

To review and present the results of a one-step method employing a free tarsal plate graft and a myocutaneous pedicle flap plus a free skin graft for reconstruction of large upper eyelid defects after tumour surgery. This was a retrospective case-series of 8 patients who underwent reconstruction of the upper eyelid after tumour removal. The horizontal defect involved 50-75% of the lid (3 pts.), more than 75% (3 pts.), and more than 75% plus the lateral canthus (2 pts.). The posterior lamella was reconstructed with contralateral upper eyelid tarsal plate. The anterior lamella was reconstructed with a laterally based myocutaneous pedicle flap in 7 patients, leaving a raw surface under the brow which was covered with a free skin graft. In 1 patient with little skin left under the brow, the anterior lamella was reconstructed with a bi-pedicle orbicularis muscle flap together with a free skin graft. All patients healed without necrosis, did not suffer from lagophthalmos, achieved reasonable cosmesis, and did not need lubricants. In one patient, a contact lens was necessary for three weeks because of corneal erosion. One patient still needs a contact lens 3 months after excision to avoid eye discomfort. Large upper eyelid defects can be reconstructed with a free tarsal plate graft and a laterally based myocutaneous pedicle flap in combination with a free skin graft. Two-step procedures can probably be avoided in most cases.

Experimental investigation of flow-induced fabrics in rocks at upper-mantle pressures: Application to understanding mantle dynamics and seismic anisotropy

Energy Technology Data Exchange (ETDEWEB)

Kohlstedt, David L. [Univ. of Minnesota, Minneapolis, MN (United States)

2016-04-26

The goal of this collaborative research effort between W.B. Durham at the Massachusetts Institute of Technology (MIT) and D.L. Kohlstedt and S. Mei at the University of Minnesota (UMN) was to exploit a newly developed technology for high-pressure, high-temperature deformation experimentation, namely, the deformation DIA (D-DIA) to determine the deformation behavior of a number of important upper mantle rock types including olivine, garnet, enstatite, and periclase. Experiments were carried out under both hydrous and anhydrous conditions and at both lithospheric and asthenospheric stress and temperature conditions. The result was a group of flow laws for Earth’s upper mantle that quantitatively describe the viscosity of mantle rocks from shallow depths (the lithosphere) to great depths (the asthenosphere). These flow laws are fundamental for modeling the geodynamic behavior and heat transport from depth to Earth’s surface.

Experimental investigation of flow-induced fabrics in rocks at upper-mantle pressures. Application to understanding mantle dynamics and seismic anisotropy

Energy Technology Data Exchange (ETDEWEB)

Durham, William B. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2016-05-02

The goal of this collaborative research effort between W.B. Durham at the Massachusetts Institute of Technology (MIT) and D.L. Kohlstedt and S. Mei at the University of Minnesota (UMN) was to exploit a newly developed technology for high-pressure, high-temperature deformation experimentation, namely, the deformation DIA (D-DIA), to determine the deformation behavior of a number of important upper mantle rock types including olivine, garnet, enstatite, and periclase. Experiments were carried out under both hydrous and anhydrous conditions and at both lithospheric and asthenospheric stress and temperature conditions. The result was a group of flow laws for Earth’s upper mantle that quantitatively describe the viscosity of mantle rocks from shallow depths (the lithosphere) to great depths (the asthenosphere). These flow laws are fundamental for modeling the geodynamic behavior and heat transport from depth to Earth’s surface.-

Deformation associated to exhumation by detachment faulting of upper mantle rocks in a fossil Ocean Continent Transition: The example of the Totalp unit in SE Switzerland

Science.gov (United States)

Picazo, S.; Manatschal, G.; Cannat, M.

2013-12-01

The exhumation of upper mantle rocks along detachment faults is widespread at Mid-Ocean Ridges and at the Ocean-Continent Transition (OCT) of rifted continental margins. Thermo-mechanical models indicate that significant strain softening of the fault rocks in the footwall is required in order to produce such large fault offsets. Our work focuses on deformation textures, and the associated mineralogy in ultramafic rocks sampled in the upper levels of the footwall next to the exhumation fault. We present two OCT examples, the Totalp relict of a paleo-Tethys OCT exposed in SE Switzerland, and the Iberian distal margin (ODP Leg 173 Site 1070). We built a new geological map and a section of the Totalp unit near Davos (SE Switzerland) and interpreted this area as a local exposure of a paleo-seafloor that is formed by an exhumed detachment surface and serpentinized peridotites. The top of the exhumed mantle rocks is made of ophicalcites that resulted from the carbonation of serpentine under static conditions at the seafloor. The ophicalcites preserve depositional contacts with Upper Jurassic to Lower Cretaceous pelagic sediments. These sequences did not exceed prehnite-pumpellyite metamorphic facies conditions, and locally escaped Alpine deformation. Thin mylonitic shear zones as well as foliated amphibole-bearing ultramafic rocks have been mapped. The age of these rocks and the link with the final exhumation history are yet unknown but since amphibole-bearing ultramafic rocks can be found as clasts in cataclasites related to the detachment fault, they pre-date detachment faulting. Our petrostructural study of the exhumed serpentinized rocks also reveals a deformation gradient from cataclasis to gouge formation within 150m in the footwall of the proposed paleo-detachment fault. This deformation postdates serpentinization. It involves a component of plastic deformation of serpentine in the most highly strained intervals that has suffered pronounced grain-size reduction and

Tectonic setting of the Tertiary volcanic rocks of the Olympic Peninsula, Washington

Science.gov (United States)

Cady, Wallace M.

1975-01-01

Lower and middle Eocene abyssal and Hawaiian type tholeiitic basalts form two accumulations that apparently were once far out on the east flank of the Juan de Fuca Ridge, within the Juan de Fuca plate. One of these (more than 15 km thick) is near the eastern and southeastern periphery of the Olympic Peninsula, and the other (about 5 km thick) is on the north. The tholeiites stratigraphically overlie and interfinger with Paleocene(?) and lower and middle Eocene marine turbidites and shales; one flow includes boulders that, like clasts in the sediments, were derived from the North American continental plate immediately to the east. The basalts are overlain stratigraphically by middle Eocene to middle Miocene clastic marine sedimentary rocks, which are in turn overlapped unconformably on the south and west by upper Miocene (?) and Pliocene, chiefly shallow-marine clastic rocks. These various peripheral rocks flank a middle or late Miocene structurally complex dome, or orocline convex to the east, in which originally east dipping and low angle late Eocene to late Miocene underthrusts are flexed. The outermost underthrust of the complex separates the chiefly volcanic peripheral rocks to the north, east, and south from stratigraphically correlative and comparable, though predominantly sedimentary, core rocks arranged in northwest trending arcuate belts or packets bounded by fault zones. Before underthrusting, and perhaps oroclinal folding connected with doming, the pre-middle Miocene section was possibly 150 to 200 km wide compared with the present Olympic Peninsula which is 120 km wide. The section accumulated on the ocean floor near the western margin of the continent, before and during subduction of the oceanic crust.

Phosphorus losses from an irrigated watershed in the Northwestern U.S.: Case study of the Upper Snake Rock Watershed

Science.gov (United States)

Watersheds utilizing surface water for irrigation often return a portion of the water to a water body. This irrigation return flow often includes sediment and nutrients that reduce the quality of the receiving water body. Research in the 82,000 ha Upper Snake Rock (USR) watershed from 2005 to 2008 s...

Stability and predictability in younger crystalline rock system: Japanese Islands case

International Nuclear Information System (INIS)

Yoshida, S.

2009-01-01

The Japanese Islands consist of igneous, sedimentary, and metamorphic rocks ranging in age from Paleozoic to Cenozoic. Among these, Carboniferous to Paleogene rocks occupy about 60% of the total area of the Japanese Islands. It should be noted that Quaternary volcanic rocks occupy only about 9% of the total area, although Quaternary volcanoes occur throughout the Japanese Islands. Long-term stability and predictability in the rock system are discussed in terms of volcanic activity, active faulting, and plate motion. Volcanic activity in the Japanese Islands is intimately related to subduction of the Pacific Plate and the Philippine Sea Plate. The volcanic front related to the Pacific and the Philippine Sea plates has been essentially fixed since about 6 Ma. The main active faults, which are distributed sporadically throughout the Japanese Islands, number about 150 and have been extensively investigated. The modes of the Pacific Plate and the Philippine Sea Plate have been essentially invariable since 10 Ma and 6 Ma, respectively. These lines of evidence imply that volcanism and tectonism in the Japanese Islands will scarcely change for hundreds of thousands of years into the future. It is clear that many places suitable for geological disposal will be present in this rock system. (author)

Nonlinear Dynamics Mechanism of Rock Burst Induced by the Instability of the Layer-Crack Plate Structure in the Coal Wall in Deep Coal Mining

Directory of Open Access Journals (Sweden)

Yanlong Chen

2017-01-01

Full Text Available The instability of layer-crack plate structure in coal wall is one of the causes of rock burst. In the present paper, we investigate the formation and instability processes of layer-crack plate structure in coal wall by experiments and theoretical analysis. The results reveal that layer-crack plate structure formed near the free surface of the coal wall during the loading. During the formation of the layer-crack plate structure, the lateral displacement curve of the coal wall experiences a jagged variation, which suggests the nonlinear instability failure of the coal wall with a sudden release of the elastic energy. Then, a dynamic model for the stability analysis of the layer-crack plate structure was proposed, which takes consideration of the dynamic disturbance factor. Based on the dynamic model, the criterion for dynamic instability of the layer-crack plate structure was determined and demonstrated by an example. According to the analytical results, some control methods of dynamic stability of the layer-crack plate structure was put forward.

Eclogite facies rocks

National Research Council Canada - National Science Library

Carswell, D. A

1990-01-01

... of eclogite evolution and genesis. The authors present a thorough treatment of the stability relations and geochemistry of these rocks, their intimate association with continental plate collision zones and suture zones...

Preliminary study of uranium favorability of upper cretaceous, paleocene, and lower eocene rocks of the Bighorn Basin, Wyoming and Montana

International Nuclear Information System (INIS)

Hesse, S.L.; Dunagan, J.F. Jr.

1978-02-01

This report presents an evaluation of the uranium favorability of continental sediments of the Upper Cretaceous Lance, Paleocene Polecat Bench, and lower Eocene Willwood Formations in the Bighorn Basin of Wyoming and Montana, an intermontane structural basin of Laramide age. Previous work dealing with the Bighorn Basin was reviewed, and field investigations were carried out in the spring and summer of 1976. Subsurface data were collected and results of surface and subsurface investigations were evaluated with respect to uranium favorability. Precambrian plutonic and metamorphic rocks and Tertiary tuffaceous rocks in the Bighorn Basin and bordering uplifts are considered insignificant as source rocks, although the Wiggins Formation (White River equivalent) cannot be evaluated as a possible source because of a lack of data. Potential host rocks locally show only limited favorability. Lithology of strata exposed along the western and southern basin margins is more favorable than that of rocks in the central and eastern parts of the basin, but there is little organic material, pyrite, or other reducing agents in these rocks. Strata of the Lance, Polecat Bench, and Willwood Formations in the Bighorn Basin are considered generally unfavorable for sandstone uranium deposits

Finite element simulations of two rock mechanics tests

International Nuclear Information System (INIS)

Dahlke, H.J.; Lott, S.A.

1986-04-01

Rock mechanics tests are performed to determine in situ stress conditions and material properties of an underground rock mass. To design stable underground facilities for the permanent storage of high-level nuclear waste, determination of these properties and conditions is a necessary first step. However, before a test and its associated equipment can be designed, the engineer needs to know the range of expected values to be measured by the instruments. Sensitivity studies by means of finite element simulations are employed in this preliminary design phase to evaluate the pertinent parameters and their effects on the proposed measurements. The simulations, of two typical rock mechanics tests, the plate bearing test and the flat-jack test, by means of the finite element analysis, are described. The plate bearing test is used to determine the rock mass deformation modulus. The flat-jack test is used to determine the in situ stress conditions of the host rock. For the plate bearing test, two finite element models are used to simulate the classic problem of a load on an elastic half space and the actual problem of a plate bearing test in an underground tunnel of circular cross section. For the flat-jack simulation, a single finite element model is used to simulate both horizontal and vertical slots. Results will be compared to closed-form solutions available in the literature

Ore-controlling mechanism of carbonaceous-siliceous-pelitic rock type uranium deposits with down-faulted red basins in the southeast continental margin of Yangtze plate

International Nuclear Information System (INIS)

Zhang Zilong; Qi Fucheng; He Zhongbo; Li Zhixing; Wang Wenquan; Yu Jinshui

2012-01-01

One of the important ore-concentrated areas of carbonaceous-siliceous-pelitic rock type uranium deposits is the Southeast continental margin of Yangtze plate. Sedimentary-exogenously transformed type and sedimentary- hydrothermal superimposed transformed type uranium deposits are always distributed at or near the edge of down-faulted red ba sins. In this paper, the distributions of the deposits are analyzed with the relation to down-faulted red basins. The connective effect and ore-controlling mechanism are proposed of carbonaceous-siliceous-pelitic rock type uranium deposits with marginal fractures of red basins. (authors)

Restoration of Circum-Arctic Upper Jurassic source rock paleolatitude based on crude oil geochemistry

Science.gov (United States)

Peters, K.E.; Ramos, L.S.; Zumberge, J.E.; Valin, Z.C.; Scotese, C.R.

2008-01-01

Tectonic geochemical paleolatitude (TGP) models were developed to predict the paleolatitude of petroleum source rock from the geochemical composition of crude oil. The results validate studies designed to reconstruct ancient source rock depositional environments using oil chemistry and tectonic reconstruction of paleogeography from coordinates of the present day collection site. TGP models can also be used to corroborate tectonic paleolatitude in cases where the predicted paleogeography conflicts with the depositional setting predicted by the oil chemistry, or to predict paleolatitude when the present day collection locality is far removed from the source rock, as might occur due to long distance subsurface migration or transport of tarballs by ocean currents. Biomarker and stable carbon isotope ratios were measured for 496 crude oil samples inferred to originate from Upper Jurassic source rock in West Siberia, the North Sea and offshore Labrador. First, a unique, multi-tiered chemometric (multivariate statistics) decision tree was used to classify these samples into seven oil families and infer the type of organic matter, lithology and depositional environment of each organofacies of source rock [Peters, K.E., Ramos, L.S., Zumberge, J.E., Valin, Z.C., Scotese, C.R., Gautier, D.L., 2007. Circum-Arctic petroleum systems identified using decision-tree chemometrics. American Association of Petroleum Geologists Bulletin 91, 877-913]. Second, present day geographic locations for each sample were used to restore the tectonic paleolatitude of the source rock during Late Jurassic time (???150 Ma). Third, partial least squares regression (PLSR) was used to construct linear TGP models that relate tectonic and geochemical paleolatitude, where the latter is based on 19 source-related biomarker and isotope ratios for each oil family. The TGP models were calibrated using 70% of the samples in each family and the remaining 30% of samples were used for model validation. Positive

Lithofacies palaeogeography of the Upper Permian Changxing Stage in the Middle and Upper Yangtze Region, China

Directory of Open Access Journals (Sweden)

He Youbin

2013-04-01

Full Text Available Based on the petrological study, according to single factor analysis and multifactor comprehensive mapping method, the quantitative lithofacies palaeogeography of the Upper Permian Changxing Stage of the Middle and Upper Yangtze Region was studied. The Changxing Stage in the Middle and Upper Yangtze Region is mainly composed of carbonate rocks; in addition, clastic and siliceous rocks occur with rare coals and pyroclastic rocks. Lithofacies can be divided into five types, including clastic rock assemblage, clastic rock–limestone assemblage, limestone assemblage, limestone–siliceous rock assemblage, and siliceous rock–clastic rock assemblage. Four fundamental ecological types and five fossil assemblages were recognized in the Changxing Stage. On the basis of the petrological and palaeoecological study, eight single factors were chosen including thickness, content of marine rocks, content of shallow water carbonate rocks, content of bioclasts with limemud matrix, content of bioclasts with sparry cement, distribution of reefs, content of thin bedded siliceous rocks and content of deep water sedimentary rocks. And eight single factor maps and one lithofacies paleogeographic map of the Changxing Stage were compiled. Paleoenvironments from west to east include an erosional area, fluvial plain, clastic platform, carbonate platform and reefs that developed there, slope and basin, low energy organic banks, and high energy organic banks. Sedimentary environments have an obvious control on the development of the source rocks, and the excellent source rocks are developed in the Dalong Formation. Changxing Stage reservoirs should be dominated by the reef and platform surrounding the Guangyuan–Liangping Basin rim area, and is the most favorable exploration area of the reef petroleum reservoirs of the Changxing Formation.

Petrologic Aspects of Seamount and Guyot Volcanism on the Ancestral Mesozoic Pacific Plate: a Review

Science.gov (United States)

Natland, J. H.

2007-12-01

lavas from the Cook-Austral, Marquesas, Society, and Samoan linear volcanic chains. Significantly, Hawaiian- type tholeiite has not been sampled in the region, and the diversity of basaltic rocks and differentiates has always been high. Even unusual potassic nephelinites (K2O > Na2O) with phenocrysts of kaersutitic amphibole or phlogopite occur in the Wake and Line Seamounts. These resemble lavas of portions of the East African Rift, but also have counterparts in the Samoan and Society chains, and resemble very young basalts obtained on the outer trench swell of the Pacific plate near Japan. I suggest that variably and often strongly enriched material was originally supplied to the shallow upper mantle beneath a broad region of the Pacific plate during the Mesozoic; that partial melts of this material were subsequently tapped along major fracture systems that developed to form linear island chains as stress configurations changed on the Pacific plate; and that narrow plume conduits of ascending mantle have never figured in the emplacement of the broadly distributed enriched SOPITA volcanoes. 1) Natland, J. H., and Winterer, E.L., 2005, GSA Spec. Paper 388: 687-710. 2) Larson, R.L., et al., 1992, Proc. ODP, Sci Results, 129: p. 615-631; 3) Staudigel, H., et al., 1991, EPSL, 102: 24-44.

The influence of walls and upper tie plate slots on the flooding mechanism in fuel elements with and without heat transfer between steam and water

International Nuclear Information System (INIS)

Spatz, R.; Mewes, D.

1989-01-01

The counter-current flow of steam and water was experimentally investigated for the upper part of a PWR fuel element. The actual geometrical shape of the nuclear equipment was simulated by various types of plates, in which bore holes and slots were arranged in different positions. The experiments were performed with and without an installed, unheated rod bundle below the plates. The water was injected at saturated and subcooled temperatures in order to observe the effects of heat transfer on counter-current flow. With increasing steam velocity the flooding occurs initially in the tie-plate area. If the rod bundle is installed in the flow duct, a part of the downwards flowing water is transported upwards from the region of the upper grid spacer to the plate. Heat transfer between the phases can cause in the counter-current flow region an instable transition from downward to near complete upward directed liquid flow. In comparison to experiments with saturated water injection, flooding occurs at larger steam velocities. Different flooding correlations, which are known from the literature, were compared with the experimental data to appraise their applicability to counter-current flow in the core of PWRs. (orig.)

Hydrology of the Upper Capibaribe Basin, Pernambuco, Brazil - A reconnaissance in an Area of Crystalline Rocks

Science.gov (United States)

Chada Filho, Luiz Goncalves; Dias Pessoa, Mario; Sinclair, William C.

1966-01-01

The upper Capibaribe basin is the western three-fourths, approximately, of the valley of the river that empties into the Atlantic Ocean at Recife, the capital of the State of Pernambuco, Brazil. It is the part of the drainage basin that is within the Drought Polygon of northeast Brazil, and it totals about 5,400 square kilometers. It receives relatively abundant precipitation in terms of the annual average, yet is regarded as hot subhumid to semiarid because the precipitation is uneven from year to year and place to place. The dependable water supply, therefore, is small. The basin has water, which could be put to better use than at present, but the opportunities for augmenting the usable supply are not great. The streams are intermittent and therefore cannot be expected to fill surface reservoirs and to keep them filled. The ground-water reservoirs have small capacity--quickly filled and quickly drained. A rough estimate based on the records for 1964 suggests that, of 4,700 million cubic meters of precipitation in the upper Capibaribe basin, 2,700 million cubic meters (57 percent) left the basin as runoff and 2,000 million cubic meters {43 percent) went into underground storage or was evaporated or transpired. The bedrock of the upper Capibaribe basin is composed of granite, gneiss, schist, and other varieties of crystalline rocks, which have only insignificant primary permeability. They are permeable mainly where fractured. The principal fracture zones, fortunately, are in the valleys, where water accumulates and can feed into them, but the volume of fractured rock is small in relation to the basin as a whole. A well in a large water-filled fracture zone may yield up to 20,000 liters per hour, but the average well yields less than one-fourth this amount, and some wells yield none. The saprolite, or weathered rock, is many meters thick at some places especially in the eastern half of the upper Capibaribe basin. It contains water locally, but ordinarily will yield

Crystallisation condition of the Quaternary basanites of volcanic centre Black Rock, monogenetic field Lunar Crater

Science.gov (United States)

Turova, Mariia; Plechov, Pavel; Scherbakov, Vasily; Larin, Nikolay

2017-04-01

The Lunar Crater volcanic field is located in a tension zone Basin and Range Province (USA). This tension is connected with dives oceanic plate under the continental plate [1]. Lunar Crater consists of flows basalt, basanite, trachybasalt has a different age [2]. In this work we investigate the youngest rock - basanite. The basanite is highly crystalline consisting of about megacrysts (3-10 cm) 30-60 wt% phenocrysts ( 800-1500 µm) and microphenocrysts (100-800 µm) and 40-60% microlites (Mathematical, Physical and Engineering Sciences. - 1981. - T. 300. - №. 1454. - C. 407-434. 2. Wood, X., and Keinle, Y., 1990, Volcanoes of North America: Cambridge,United Kingdom, Cambridge University Press, 354 p. 3. Nimis P. Clinopyroxene geobarometry of magmatic rocks. Part 2. Structural geobarometers for basic to acid, tholeiitic and mildly alkaline magmatic systems //Contributions to Mineralogy and Petrology. - 1999. - T. 135. - №. 1. - C. 62-74. 4. Ballhaus C., Berry R. F., Green D. H. High pressure experimental calibration of the olivine-orthopyroxene-spinel oxygen geobarometer: implications for the oxidation state of the upper mantle //Contributions to Mineralogy and Petrology. - 1991. - T. 107. - №. 1. - C. 27-40.

Rheological structure of the lithosphere in plate boundary strike-slip fault zones

Science.gov (United States)

Chatzaras, Vasileios; Tikoff, Basil; Kruckenberg, Seth C.; Newman, Julie; Titus, Sarah J.; Withers, Anthony C.; Drury, Martyn R.

2016-04-01

How well constrained is the rheological structure of the lithosphere in plate boundary strike-slip fault systems? Further, how do lithospheric layers, with rheologically distinct behaviors, interact within the strike-slip fault zones? To address these questions, we present rheological observations from the mantle sections of two lithospheric-scale, strike-slip fault zones. Xenoliths from ˜40 km depth (970-1100 ° C) beneath the San Andreas fault system (SAF) provide critical constraints on the mechanical stratification of the lithosphere in this continental transform fault. Samples from the Bogota Peninsula shear zone (BPSZ, New Caledonia), which is an exhumed oceanic transform fault, provide insights on lateral variations in mantle strength and viscosity across the fault zone at a depth corresponding to deformation temperatures of ˜900 ° C. Olivine recrystallized grain size piezometry suggests that the shear stress in the SAF upper mantle is 5-9 MPa and in the BPSZ is 4-10 MPa. Thus, the mantle strength in both fault zones is comparable to the crustal strength (˜10 MPa) of seismogenic strike-slip faults in the SAF system. Across the BPSZ, shear stress increases from 4 MPa in the surrounding rocks to 10 MPa in the mylonites, which comprise the core of the shear zone. Further, the BPSZ is characterized by at least one order of magnitude difference in the viscosity between the mylonites (1018 Paṡs) and the surrounding rocks (1019 Paṡs). Mantle viscosity in both the BPSZ mylonites and the SAF (7.0ṡ1018-3.1ṡ1020 Paṡs) is relatively low. To explain our observations from these two strike-slip fault zones, we propose the "lithospheric feedback" model in which the upper crust and lithospheric mantle act together as an integrated system. Mantle flow controls displacement and the upper crust controls the stress magnitude in the system. Our stress data combined with data that are now available for the middle and lower crustal sections of other transcurrent fault

Lithospheric strength in the active boundary between the Pacific Plate and Baja California microplate constrained from lower crustal and upper mantle xenoliths

Science.gov (United States)

Chatzaras, Vasileios; van der Werf, Thomas; Kriegsman, Leo M.; Kronenberg, Andreas; Tikoff, Basil; Drury, Martyn R.

2017-04-01

The lower crust is the most poorly understood of the lithospheric layers in terms of its rheology, particularly at active plate boundaries. We studied naturally deformed lower crustal xenoliths within an active plate boundary, in order to link their microstructures and rheological parameters to the well-defined active tectonic context. The Baja California shear zone (BCSZ), located at the western boundary of the Baja California microplate, comprises the active boundary accommodating the relative motion between the Pacific plate and Baja California microplate. The basalts of the Holocene San Quintin volcanic field carry lower crustal and upper mantle xenoliths, which sample the Baja California microplate lithosphere in the vicinity of the BCSZ. The lower crustal xenoliths range from undeformed gabbros to granoblastic two-pyroxene granulites. Two-pyroxene geothermometry shows that the granulites equilibrated at temperatures of 690-920 oC. Phase equilibria (P-T pseudosections using Perple_X) indicate that symplectites with intergrown pyroxenes, plagioclase, olivine and spinel formed at 3.6-5.4 kbar, following decompression from pressures exceeding 6 kbar. FTIR spectroscopy shows that the water content of plagioclase varies among the analyzed xenoliths; plagioclase is relatively dry in two xenoliths while one xenolith contains hydrated plagioclase grains. Microstructural observations and analysis of the crystallographic texture provide evidence for deformation of plagioclase by a combination of dislocation creep and grain boundary sliding. To constrain the strength of the lower crust and upper mantle near the BCSZ we estimated the differential stress using plagioclase and olivine grain size paleopiezomtery, respectively. Differential stress estimates for plagioclase range from 10 to 32 MPa and for olivine are 30 MPa. Thus the active microplate boundary records elevated crustal temperatures, heterogeneous levels of hydration, and low strength in both the lower crust and

Study of the radioactivity of rocks by the photographic method

Energy Technology Data Exchange (ETDEWEB)

Picciotto, E E

1949-08-16

The use of photographic plates, and especially of the new Ilford and Kodak plates, in nuclear physics is briefly described. In particular, the application of these methods to the study of the radioactivity of rocks is discussed. In a series of studies made by the authors, the photographic plates were placed in close contact with a thin, highly polished sheet of the rock sample and then developed under specified conditions. This method was used to determine the concentration of U and Th in two radioactive rock samples and the results are given. The samples were then reduced to powder form and the concentrations were again determined. Work on dissolved samples has not yet been completed. In conclusion, the relative merits of these different techniques are indicated.

Using rocks to reveal the inner workings of magma chambers below volcanoes in Alaska’s National Parks

Science.gov (United States)

Coombs, Michelle L.; Bacon, Charles R.

2012-01-01

Alaska is one of the most vigorously volcanic regions on the planet, and Alaska’s national parks are home to many of the state’s most active volcanoes. These pose both local and more distant hazards in the form of lava and pyroclastic flows, lahars (mudflows), ash clouds, and ash fall. Alaska’s volcanoes lie along the arc of the Aleutian-Alaskan subduction zone, caused as the oceanic Pacific plate moves northward and dips below the North American plate. These volcanoes form as water-rich fluid from the down-going Pacific plate is released, lowering the melting temperature of rock in the overlying mantle and enabling it to partially melt. The melted rock (magma) migrates upward, collecting at the base of the approximately 25 mile (40 km) thick crust, occasionally ascending into the shallow crust, and sometimes erupting at the earth’s surface.During volcanic unrest, scientists use geophysical signals to remotely visualize volcanic processes, such as movement of magma in the upper crust. In addition, erupted volcanic rocks, which are quenched samples of magmas, can tell us about subsurface magma characteris-tics, history, and the processes that drive eruptions. The chemical compositions of and the minerals present in the erupted magmas can reveal conditions under which these magmas were stored in crustal “chambers”. Studies of the products of recent eruptions of Novarupta (1912), Aniakchak (1931), Trident (1953-74), and Redoubt (2009) volcanoes reveal the depths and temperatures of magma storage, and tell of complex interactions between magmas of different compositions. One goal of volcanology is to determine the processes that drive or trigger eruptions. Information recorded in the rocks tells us about these processes. Here, we demonstrate how geologists gain these insights through case studies from four recent eruptions of volcanoes in Alaska national parks.

Upper internals of PWR with coolant flow separator

International Nuclear Information System (INIS)

Chevereau, G.; Heuze, A.

1989-01-01

The upper internals for a PWR has a collecting volume for the coolant merging from the core and an apparatus for separating the flow of coolant. This apparatus has a guide for the control rods, a lower plate perforated to allow the coolant through from the core, an upper plate also perforated to allow the coolant through to the collecting volume and a peripheral binding ring joining the two plates. Each guide comprises an envelope without holes and joined perceptibly tight to the plates [fr

Frictional sliding in layered rock: laboratory-scale experiments

International Nuclear Information System (INIS)

Buescher, B.J.; Perry, K.E. Jr.; Epstein, J.S.

1996-09-01

The work is part of the rock mechanics effort for the Yucca Mountain Site Characterization Program. The laboratory-scale experiments are intended to provide high quality data on the mechanical behavior of jointed structures that can be used to validate complex numerical models for rock-mass behavior. Frictional sliding between simulated rock joints was studied using phase shifting moire interferometry. A model, constructed from stacks of machined and sandblasted granite plates, contained a central hole bore normal to the place so that frictional slip would be induced between the plates near the hole under compressive loading. Results show a clear evolution of slip with increasing load. Since the rock was not cycled through loading- unloading, the quantitative differences between the three data sets are probably due to a ''wearing-in'' effect. The highly variable spatial frequency of the data is probably due to the large grain size of the granite and the stochastic frictional processes. An unusual feature of the evolution of slip with increasing load is that as the load gets larger, some plates seem to return to a null position. Figs, 6 refs

Instability of a cantilevered flexible plate in viscous channel flow

Science.gov (United States)

Balint, T. S.; Lucey, A. D.

2005-10-01

The stability of a flexible cantilevered plate in viscous channel flow is studied as a representation of the dynamics of the human upper airway. The focus is on instability mechanisms of the soft palate (flexible plate) that cause airway blockage during sleep. We solve the Navier Stokes equations for flow with Reynolds numbers up to 1500 fully coupled with the dynamics of the plate motion solved using finite-differences. The study is 2-D and based upon linearized plate mechanics. When both upper and lower airways are open, the plate is found to lose its stability through a flutter mechanism and a critical Reynolds number exists. When one airway is closed, the plate principally loses its stability through a divergence mechanism and a critical flow speed exists. However, below the divergence-onset flow speed, flutter can exist for low levels of structural damping in the flexible plate. Our results serve to extend understanding of flow-induced instability of cantilevered flexible plates and will ultimately improve the diagnosis and treatment of upper-airway disorders.

Does permanent extensional deformation in lower forearc slopes indicate shallow plate-boundary rupture?

Science.gov (United States)

Geersen, J.; Ranero, C. R.; Kopp, H.; Behrmann, J. H.; Lange, D.; Klaucke, I.; Barrientos, S.; Diaz-Naveas, J.; Barckhausen, U.; Reichert, C.

2018-05-01

Seismic rupture of the shallow plate-boundary can result in large tsunamis with tragic socio-economic consequences, as exemplified by the 2011 Tohoku-Oki earthquake. To better understand the processes involved in shallow earthquake rupture in seismic gaps (where megathrust earthquakes are expected), and investigate the tsunami hazard, it is important to assess whether the region experienced shallow earthquake rupture in the past. However, there are currently no established methods to elucidate whether a margin segment has repeatedly experienced shallow earthquake rupture, with the exception of mechanical studies on subducted fault-rocks. Here we combine new swath bathymetric data, unpublished seismic reflection images, and inter-seismic seismicity to evaluate if the pattern of permanent deformation in the marine forearc of the Northern Chile seismic gap allows inferences on past earthquake behavior. While the tectonic configuration of the middle and upper slope remains similar over hundreds of kilometers along the North Chilean margin, we document permanent extensional deformation of the lower slope localized to the region 20.8°S-22°S. Critical taper analyses, the comparison of permanent deformation to inter-seismic seismicity and plate-coupling models, as well as recent observations from other subduction-zones, including the area that ruptured during the 2011 Tohoku-Oki earthquake, suggest that the normal faults at the lower slope may have resulted from shallow, possibly near-trench breaking earthquake ruptures in the past. In the adjacent margin segments, the 1995 Antofagasta, 2007 Tocopilla, and 2014 Iquique earthquakes were limited to the middle and upper-slope and the terrestrial forearc, and so are upper-plate normal faults. Our findings suggest a seismo-tectonic segmentation of the North Chilean margin that seems to be stable over multiple earthquake cycles. If our interpretations are correct, they indicate a high tsunami hazard posed by the yet un

Magnetization of lower oceanic crust and upper mantle

Science.gov (United States)

Kikawa, E.

2004-05-01

The location of the magnetized rocks of the oceanic crust that are responsible for sea-floor spreading magnetic anomalies has been a long-standing problem in geophysics. The recognition of these anomalies was a key stone in the development of the theory of plate tectonics. Our present concept of oceanic crustal magnetization is much more complex than the original, uniformly magnetized model of Vine-Matthews-Morley Hypothesis. Magnetic inversion studies indicated that the upper oceanic extrusive layer (Layer 2A of 0.5km thick) was the only magnetic layer and that it was not necessary to postulate any contribution from deeper parts of oceanic crust. Direct measurements of the magnetic properties of the rocks recovered from the sea floor, however, have shown that the magnetization of Layer 2A, together with the observations that this layer could record geomagnetic field reversals within a vertical section, is insufficient to give the required size of observed magnetic anomalies and that some contribution from lower intrusive rocks is necessary. Magnetization of oceanic intrusive rocks were observed to be reasonably high enough to contribute to sea-floor spreading magnetic anomalies, but were considered somewhat equivocal until late 1980Os, in part because studies had been conducted on unoriented dredged and ophiolite samples and on intermittent DSDP/ODP cores. Since ODP Leg 118 that cored and recovered continuous 500m of oceanic intrusive layer at Site 735B, Southwest Indian Ridge with an extremely high recovery of 87 percent, there have been several ODP Legs (legs 147, 153, 176, 179 and 209) that were devoted to drilling gabbroic rocks and peridotites. In terms of the magnetization intensities, all of the results obtained from these ODP Legs were supportive of the model that a significant contribution must come from gabbros and peridotites and the source of the lineated magnetic anomalies must reside in most of the oceanic crust as well as crust-mantle boundary

Oil prospection using the tectonic plate model

Science.gov (United States)

Pointu, Agnès

2015-04-01

Tectonic plate models are an intellectual setting to understand why oil deposits are so uncommon and unequally distributed and how models can be used in actual oil and gas prospection. In this case, we use the example of the Ghawar deposit (Saudi Arabia), one of the largest producing well in the world. In the first step, physical properties of rocks composing the oil accumulation are studied by laboratory experiments. Students estimate the porosity of limestone and clay by comparing their mass before and after water impregnation. Results are compared to microscopic observations. Thus, students come to the conclusion that oil accumulations are characterized by superposition of rocks with very different properties: a rich organic source rock (clays of the Hanifa formation), a porous reservoir rock to store the petroleum in (limestones of the Arab formation) and above an impermeable rock with very low porosity (evaporites of the Tithonien). In previous lessons, students have seen that organic matter is usually mineralized by bacteria and that this preservation requires particular conditions. The aim is to explain why biomass production has been so important during the deposit of the clays of the Hanifa formation. Tectonic plate models make it possible to estimate the location of the Arabian Peninsula during Jurassic times (age of Hanifa formation). In order to understand why the paleo-location of the Arabian Peninsula is important to preserve organic matter, students have different documents showing: - That primary production of biomass by phytoplankton is favored by climatic conditions, - That the position of continents determinate the ocean currents and the positions of upwelling zones and zones where organic matter will be able to be preserved, - That north of the peninsula there was a passive margin during Jurassic times. An actual seismic line is studied in order to highlight that this extensive area allowed thick sedimentary deposits to accumulate and that fast

Permeability in fractured rocks from deep geothermal boreholes in the Upper Rhine Graben

Science.gov (United States)

Vidal, Jeanne; Whitechurch, Hubert; Genter, Albert; Schmittbuhl, Jean; Baujard, Clément

2015-04-01

Permeability in fractured rocks from deep geothermal boreholes in the Upper Rhine Graben Vidal J.1, Whitechurch H.1, Genter A.2, Schmittbuhl J.1, Baujard C.2 1 EOST, Université de Strasbourg 2 ES-Géothermie, Strasbourg The thermal regime of the Upper Rhine Graben (URG) is characterized by a series of geothermal anomalies on its French part near Soultz-sous-Forêts, Rittershoffen and in the surrounding area of Strasbourg. Sedimentary formations of these areas host oil field widely exploited in the past which exhibit exceptionally high temperature gradients. Thus, geothermal anomalies are superimposed to the oil fields which are interpreted as natural brine advection occurring inside a nearly vertical multi-scale fracture system cross-cutting both deep-seated Triassic sediments and Paleozoic crystalline basement. The sediments-basement interface is therefore very challenging for geothermal industry because most of the geothermal resource is trapped there within natural fractures. Several deep geothermal projects exploit local geothermal energy to use the heat or produce electricity and thus target permeable fractured rocks at this interface. In 1980, a geothermal exploration well was drilled close to Strasbourg down to the Permian sediments at 3220 m depth. Bottom hole temperature was estimated to 148°C but the natural flow rate was too low for an economic profitability (geothermal site by drilling five boreholes, three of which extend to 5 km depth. They identified a temperature of 200° C at 5 km depth in the granitic basement but with a variable flow rate. Hydraulic and chemical stimulation operations were applied in order to increase the initial low permeability by reactivating and dissolving sealed fractures in basement. The productivity was considerably improved and allows geothermal exploitation at 165° C and 20 L/s. Recent studies revealed the occurrences of permeable fractures in the limestones of Muschelkalk and the sandstones of Buntsandstein also. For

Role of Transtension in Rifting at the Pacific-North America Plate Boundary

Science.gov (United States)

Stock, J. M.

2011-12-01

Transtensional plate motion can be accommodated either in a localized zone of transtensional rifting or over a broader region. Broader zones of deformation can be classified either as diffuse deformation or strain partitioning (one or more major strike-slip shear zones geographically offset from a region of a extensional faulting). The Pacific-North America plate boundary in southwestern North America was transtensional during much of its history and has exhibited the full range of these behaviors at different spatial scales and in different locations, as recorded by fault motions and paleomagnetic rotations. Here we focus on the northern Gulf of California part of the plate boundary (Upper and Lower Delfin basin segments), which has been in a zone of transtensional Pacific-North America plate boundary motion ever since the middle Miocene demise of adjacent Farallon-derived microplates. Prior to the middle Miocene, during the time of microplate activity, this sector of North America experienced basin-and-range normal faults (core complexes) in Sonora. However there is no evidence of continued extensional faulting nor of a Gulf-related topographic depression until after ca 12 Ma when a major ignimbrite (Tuff of San Felipe/ Ignimbrite of Hermosillo) was deposited across the entire region of the future Gulf of California rift in this sector. After 12 Ma, faults disrupted this marker bed in eastern Baja California and western Sonora, and some major NNW-striking right-lateral faults are inferred to have developed near the Sonoran coast causing offset of some of the volcanic facies. However, there are major tectonic rotations of the volcanic rocks in NE Baja California between 12 and 6 Ma, suggesting that the plate boundary motion was still occurring over a broad region. By contrast, after about 6 Ma, diminished rotations in latest Miocene and Pliocene volcanic rocks, as well as fault slip histories, show that plate boundary deformation became localized to a narrower

History and Evolution of Precambrian plate tectonics

Science.gov (United States)

Fischer, Ria; Gerya, Taras

2014-05-01

Plate tectonics is a global self-organising process driven by negative buoyancy at thermal boundary layers. Phanerozoic plate tectonics with its typical subduction and orogeny is relatively well understood and can be traced back in the geological records of the continents. Interpretations of geological, petrological and geochemical observations from Proterozoic and Archean orogenic belts however (e.g., Brown, 2006), suggest a different tectonic regime in the Precambrian. Due to higher radioactive heat production the Precambrian lithosphere shows lower internal strength and is strongly weakened by percolating melts. The fundamental difference between Precambrian and Phanerozoic tectonics is therefore the upper-mantle temperature, which determines the strength of the upper mantle (Brun, 2002) and the further tectonic history. 3D petrological-thermomechanical numerical modelling experiments of oceanic subduction at an active plate at different upper-mantle temperatures show these different subduction regimes. For upper-mantle temperatures 250 K above the present day value no subduction occurs any more. The whole lithosphere is delaminating and due to strong volcanism and formation of a thicker crust subduction is inhibited. This stage of 200-250 K higher upper mantle temperature which corresponds roughly to the early Archean (Abbott, 1994) is marked by strong volcanism due to sublithospheric decompression melting which leads to an equal thickness for both oceanic and continental plates. As a consequence subduction is inhibited, but a compressional setup instead will lead to orogeny between a continental or felsic terrain and an oceanic or mafic terrain as well as internal crustal convection. Small-scale convection with plume shaped cold downwellings also in the upper mantle is of increased importance compared to the large-scale subduction cycle observed for present temperature conditions. It is also observed that lithospheric downwellings may initiate subduction by

Mineral and rock chemistry of Mata da Corda Kamafugitic Rocks (Minas Gerais State, Brazil)

International Nuclear Information System (INIS)

Albuquerque Sgarbi, Patricia B. de; Valenca, Joel G.

1995-01-01

The volcanic rocks of the Mata da Corda Formation (Upper Cretaceous) in Minas Gerais, Brazil, are mafic potassic to ultra potassic rocks of kamafugitic affinity containing essentially clinopyroxenes, perovskite, magnetite and occasionally olivine, phlogopite, melilite pseudomorphs and apatite. The felsic phases are kalsilite and/or leucite pseudomorphs. The rocks are classified as mafitites, leucitites and kalsilitites. The analysis of the available data of the rocks studied, based on the relevant aspects of the main proposals for the classification of alkaline mafic to ultramafic potassic rocks leads to the conclusion that Sahama's (1974) proposal to divide potassium rich alkaline rocks in two large families is the one to which the Mata da Corda rocks adapt best. According to this and the data in the literature on the mineralogy and mineral and rock chemistries of the other similar occurrences, these rocks may be interpreted as alkaline potassic to ultra potassic rocks of hamafugitic affinity. 11 figs., 5 tabs

Development of a Unified Rock Bolt Model in Discontinuous Deformation Analysis

Science.gov (United States)

He, L.; An, X. M.; Zhao, X. B.; Zhao, Z. Y.; Zhao, J.

2018-03-01

In this paper, a unified rock bolt model is proposed and incorporated into the two-dimensional discontinuous deformation analysis. In the model, the bolt shank is discretized into a finite number of (modified) Euler-Bernoulli beam elements with the degrees of freedom represented at the end nodes, while the face plate is treated as solid blocks. The rock mass and the bolt shank deform independently, but interact with each other through a few anchored points. The interactions between the rock mass and the face plate are handled via general contact algorithm. Different types of rock bolts (e.g., Expansion Shell, fully grouted rebar, Split Set, cone bolt, Roofex, Garford and D-bolt) can be realized by specifying the corresponding constitutive model for the tangential behavior of the anchored points. Four failure modes, namely tensile failure and shear failure of the bolt shank, debonding along the bolt/rock interface and loss of the face plate, are available in the analysis procedure. The performance of a typical conventional rock bolt (fully grouted rebar) and a typical energy-absorbing rock bolt (D-bolt) under the scenarios of suspending loosened blocks and rock dilation is investigated using the proposed model. The reliability of the proposed model is verified by comparing the simulation results with theoretical predictions and experimental observations. The proposed model could be used to reveal the mechanism of each type of rock bolt in realistic scenarios and to provide a numerical way for presenting the detailed profile about the behavior of bolts, in particular at intermediate loading stages.

Eos Chaos Rocks

Science.gov (United States)

2006-01-01

11 January 2006 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows light-toned, layered rock outcrops in Eos Chaos, located near the east end of the Valles Marineris trough system. The outcrops occur in the form of a distinct, circular butte (upper half of image) and a high slope (lower half of image). The rocks might be sedimentary rocks, similar to those found elsewhere exposed in the Valles Marineris system and the chaotic terrain to the east of the region. Location near: 12.9oS, 49.5oW Image width: 3 km (1.9 mi) Illumination from: lower left Season: Southern Summer

Seismological observations at the Northern Andean region of Colombia: Evidence for a shallowly subducting Caribbean Slab and an extensional regime in the upper plate

Science.gov (United States)

Monsalve, G.; Cardona, A.; Yarce, J.; Alvira, D.; Poveda, E.

2013-05-01

A number of seismological observations, among which we can mention teleseismic travel time residuals, P to S receiver functions and Pn velocity quantification, suggest a clear distinction between the seismic structure of the crust and uppermost mantle between the plains on the Caribbean coast of Colombia and the mountains at the Northern Andean region. Absolute and relative travel time residuals indicate the presence of a seismically fast material in the upper mantle beneath northern Colombia; preliminary results of Pn studies show a region of relatively slow Pn velocities (between 7.8 and 7.9 km/s) underneath the Caribbean coast, contrasting with values greater than 8 km/s beneath the Central and Western cordilleras of Colombia, and the Pacific coast; receiver functions suggest a significantly thinner crust beneath the Caribbean coast, with a crustal thickness between 25 and 30 km, than beneath the Northern Andean zone at the cordilleras of Colombia, where it exceeds 40 km and reaches about 57 km at the location of Bogota. Besides the obviuos discrepancies that appear in response to different topography, we think that the seismological observations are a consequence of the presence of two very distinct slab segments beneath Colombia and contrasting behaviors of the upper plate, which correspond to Caribbean and Nazca subductions. Our seismic observations can be explained by a shallowly subducting Caribbean Plate, in the absence of an asthenospheric wedge, that steepens at about the location of the Bucaramanga nest, and a thinned continental crust that reflects an extensional component linked to oblique convergence of the Caribbean, which contrasts with the crustal thickening in the Andean Cordillera linked to crustal shortening and Nazca plate subuction. These new data are consistent with the idea of of a relatively warm Nazca slab of Neogene age which seems to have a relatively frontal convergence, and a colder, more buoyant Caribbean slab which represents an

Cyclic Sequences, Events and Evolution of the Sino-Korean Plate,with a Discussion on the Evolution of Molar-tooth Carbonates,Phosphorites and Source Rocks

Institute of Scientific and Technical Information of China (English)

MENG Xianghua; GE Ming

2003-01-01

This paper gives an account of the research that the authors conducted on the cyclic sequences, events and evolutionary history from Proterozoic to Meso-Cenozoic in the Sino-Korean plate based on the principle of the Cosmos-Earth System. The authors divided this plate into 20 super-cyclic or super-mega-cyclic periods and more than 100 Oort periods. The research focused on important sea flooding events, uplift interruption events, tilting movement events, molar-tooth carbonate events, thermal events, polarity reversal events, karst events, volcanic explosion events and storm events, as well as types of resource areas and paleotectonic evolution. By means of the isochronous theory of the Cosmos-Earth System periodicity and based on long-excentricity and periodicity, the authors elaborately studied the paleogeographic evolution of the aulacogen of the Sino-Korean plate, the oolitic beach platform formation, the development of foreland basin and continental rift valley basin, and reconstructed the evolution of tectonic paleogeography and stratigraphic framework in the Sino-Korean plate in terms of evolutionary maps. Finally, the authors gave a profound discussion on the formation and development of molar-tooth carbonates, phosphorites and source rocks.

Excess europium content in Precambrian sedimentary rocks and continental evolution

Science.gov (United States)

Jakes, P.; Taylor, S. R.

1974-01-01

It is proposed that the europium excess in Precambrian sedimentary rocks, relative to those of younger age, is derived from volcanic rocks of ancient island arcs, which were the source materials for the sediments. Precambrian sedimentary rocks and present-day volcanic rocks of island arcs have similar REE patterns, total REE abundances, and excess Eu, relative to the North American shale composite. The present upper crustal REE pattern, as exemplified by that of sediments, is depleted in Eu, relative to chondrites. This depletion is considered to be a consequence of development of a granodioritic upper crust by partial melting in the lower crust, which selectively retains europium.

Lower Paleozoic carbonate rocks of Baird Mountains Quadrangle, Alaska

Energy Technology Data Exchange (ETDEWEB)

Dumoulin, J.A.; Harris, A.G.

1985-04-01

Lower Paleozoic carbonate rocks in the Baird Mountains quadrangle form a relatively thin (about 550 m), chiefly shallow-water succession that has been imbricately thrust and metamorphosed to lower greenschist facies. Middle and Upper Cambrian rocks - the first reported from the western Brooks Range - occur in the northeastern quarter of the quadrangle, south of Angayukaqsraq (formerly Hub) Mountain. They consist of marble grading upward into thin-bedded marble/dolostone couplets and contain pelagiellid mollusks, acetretid brachiopods, and agnostid trilobites. Sedimentologic features and the Pelagiellas indicate a shallow-water depositional environment. Overlying these rocks are Lower and Middle Ordovician marble and phyllite containing graptolites and conodonts of midshelf to basinal aspect. Upper Ordovician rocks in this area are bioturbated to laminated dolostone containing warm, shallow-water conodonts. In the Omar and Squirrel Rivers areas to the west, the Lower Ordovician carbonate rocks show striking differences in lithofacies, biofacies, and thickness. Here they are mainly dolostone with locally well-developed fenestral fabric and evaporite molds, and bioturbated to laminated orange- and gray-weathering dolomitic marble. Upper Silurian dolostone, found near Angayukaqsraq Mountain and on the central Squirrel River, contains locally abundant corals and stronmatoporoids. Devonian carbonate rocks are widely distributed in the Baird Mountains quadrangle; at least two distinct sequences have been identified. In the Omar area, Lower and Middle Devonian dolostone and marble are locally cherty and rich in megafossils. In the north-central (Nakolik River) area, Middle and Upper Devonian marble is interlayered with planar to cross-laminated quartz-carbonate metasandstone and phyllite.

Evidence for Sexual Dimorphism in the Plated Dinosaur Stegosaurus mjosi (Ornithischia, Stegosauria) from the Morrison Formation (Upper Jurassic) of Western USA.

Science.gov (United States)

Saitta, Evan Thomas

2015-01-01

Conclusive evidence for sexual dimorphism in non-avian dinosaurs has been elusive. Here it is shown that dimorphism in the shape of the dermal plates of Stegosaurus mjosi (Upper Jurassic, western USA) does not result from non-sex-related individual, interspecific, or ontogenetic variation and is most likely a sexually dimorphic feature. One morph possessed wide, oval plates 45% larger in surface area than the tall, narrow plates of the other morph. Intermediate morphologies are lacking as principal component analysis supports marked size- and shape-based dimorphism. In contrast, many non-sex-related individual variations are expected to show intermediate morphologies. Taphonomy of a new quarry in Montana (JRDI 5ES Quarry) shows that at least five individuals were buried in a single horizon and were not brought together by water or scavenger transportation. This new site demonstrates co-existence, and possibly suggests sociality, between two morphs that only show dimorphism in their plates. Without evidence for niche partitioning, it is unlikely that the two morphs represent different species. Histology of the new specimens in combination with studies on previous specimens indicates that both morphs occur in fully-grown individuals. Therefore, the dimorphism is not a result of ontogenetic change. Furthermore, the two morphs of plates do not simply come from different positions on the back of a single individual. Plates from all positions on the body can be classified as one of the two morphs, and previously discovered, isolated specimens possess only one morph of plates. Based on the seemingly display-oriented morphology of plates, female mate choice was likely the driving evolutionary mechanism rather than male-male competition. Dinosaur ornamentation possibly served similar functions to the ornamentation of modern species. Comparisons to ornamentation involved in sexual selection of extant species, such as the horns of bovids, may be appropriate in predicting the

Experimental investigation of the unsteady two-phase flow through perforated plates

International Nuclear Information System (INIS)

Tartaglia, G.P.

1985-07-01

The coolant flow across the perforated dip-plate during a hypothetical core disruptive accident (HCDA) in a liquid metal fast breeder reactor was simulated in a one-dimensional model. Experiments with a water-air mixture as fluid were run by varying the following parameters: geometry of the dip-plate (perforation ratio, number of the holes), height of the fluid head over the dip-plate, air volumetric fraction, size of the air bubbles, acceleration of the fluid. The pressure drop across the dip-plate, the forces acting on the dip-plate and on the upper plate, acceleration and displacement of the piston, the air volumetric fraction and the size of the air bubbles were measured in a wide range of Strouhal and acceleration numbers. The flow pattern downstream the dip-plate was filmed with a high-speed camera. The following correlations were investigated: resistance coefficients as a function of the acceleration and Strouhal number, time delay of the force on the upper plate as a function of the cavitation number, and forces and impulses acting on the upper plate compared with those acting on the dip-plate. Finally, using high-speed film pictures, the formation of fluid jets downstream the dip-plate was investigated. The following relations were obtained: displacement of the mixture surface and of the jets as a function of the perforation ratio and of the air volumetric fraction, and cavitation volume as a function of the cavitation number. (orig.) [de

Preliminary stratigraphy and facies analysis of the Upper Cretaceous Kaguyak Formation, including a brief summary of newly discovered oil stain, upper Alaska Peninsula

Science.gov (United States)

Wartes, Marwan A.; Decker, Paul L.; Stanley, Richard G.; Herriott, Trystan M.; Helmold, Kenneth P.; Gillis, Robert J.

2013-01-01

The Alaska Division of Geological and Geophysical Surveys has an ongoing program aimed at evaluating the Mesozoic forearc stratigraphy, structure, and petroleum systems of lower Cook Inlet. Most of our field studies have focused on the Jurassic component of the petroleum system (this report). However, in late July and early August of 2012, we initiated a study of the stratigraphy and reservoir potential of the Upper Cretaceous Kaguyak Formation. The Kaguyak Formation is locally well exposed on the upper Alaska Peninsula (fig. 25) and was named by Keller and Reiser (1959) for a sequence of interbedded siltstone and sandstone of upper Campanian to Maastrichtian age that they estimated to be 1,450 m thick.Subsequent work by Detterman and Miller (1985) examined 900 m of section and interpreted the unit as the record of a prograding submarine fan.This interpretation of deep-water deposition contrasts with other Upper Cretaceous rocks exposed along the Alaska Peninsula and lower Cook Inlet that are generally described as nonmarine to shallow marine (Detterman and others, 1996; LePain and others, 2012).Based on foraminifera and palynomorphs from the COST No. 1 well, Magoon (1986) concluded that the Upper Cretaceous rocks were deposited in a variety of water depths and environments ranging from upper bathyal to nonmarine. During our recent fieldwork west and south of Fourpeaked Mountain, we similarly encountered markedly varying lithofacies in the Kaguyak Formation (fig. 25), and we also found oil-stained rocks that are consistent with the existence of an active petroleum system in Upper Cretaceous rocks on the upper Alaska Peninsula and in lower Cook Inlet. These field observations are summarized below.

Aperture-based antihydrogen gravity experiment: Parallel plate geometry

Science.gov (United States)

Rocha, J. R.; Hedlof, R. M.; Ordonez, C. A.

2013-10-01

An analytical model and a Monte Carlo simulation are presented of an experiment that could be used to determine the direction of the acceleration of antihydrogen due to gravity. The experiment would rely on methods developed by existing antihydrogen research collaborations. The configuration consists of two circular, parallel plates that have an axis of symmetry directed away from the center of the earth. The plates are separated by a small vertical distance, and include one or more pairs of circular barriers that protrude from the upper and lower plates, thereby forming an aperture between the plates. Antihydrogen annihilations that occur just beyond each barrier, within a "shadow" region, are asymmetric on the upper plate relative to the lower plate. The probability for such annihilations is determined for a point, line and spheroidal source of antihydrogen. The production of 100,000 antiatoms is predicted to be necessary for the aperture-based experiment to indicate the direction of free fall acceleration of antimatter, provided that antihydrogen is produced within a sufficiently small antiproton plasma at a temperature of 4 K.

Aperture-based antihydrogen gravity experiment: Parallel plate geometry

Energy Technology Data Exchange (ETDEWEB)

Rocha, J. R.; Hedlof, R. M.; Ordonez, C. A. [Department of Physics, University of North Texas, Denton, Texas 76203 (United States)

2013-10-15

An analytical model and a Monte Carlo simulation are presented of an experiment that could be used to determine the direction of the acceleration of antihydrogen due to gravity. The experiment would rely on methods developed by existing antihydrogen research collaborations. The configuration consists of two circular, parallel plates that have an axis of symmetry directed away from the center of the earth. The plates are separated by a small vertical distance, and include one or more pairs of circular barriers that protrude from the upper and lower plates, thereby forming an aperture between the plates. Antihydrogen annihilations that occur just beyond each barrier, within a “shadow” region, are asymmetric on the upper plate relative to the lower plate. The probability for such annihilations is determined for a point, line and spheroidal source of antihydrogen. The production of 100,000 antiatoms is predicted to be necessary for the aperture-based experiment to indicate the direction of free fall acceleration of antimatter, provided that antihydrogen is produced within a sufficiently small antiproton plasma at a temperature of 4 K.

Aperture-based antihydrogen gravity experiment: Parallel plate geometry

Directory of Open Access Journals (Sweden)

J. R. Rocha

2013-10-01

Full Text Available An analytical model and a Monte Carlo simulation are presented of an experiment that could be used to determine the direction of the acceleration of antihydrogen due to gravity. The experiment would rely on methods developed by existing antihydrogen research collaborations. The configuration consists of two circular, parallel plates that have an axis of symmetry directed away from the center of the earth. The plates are separated by a small vertical distance, and include one or more pairs of circular barriers that protrude from the upper and lower plates, thereby forming an aperture between the plates. Antihydrogen annihilations that occur just beyond each barrier, within a “shadow” region, are asymmetric on the upper plate relative to the lower plate. The probability for such annihilations is determined for a point, line and spheroidal source of antihydrogen. The production of 100,000 antiatoms is predicted to be necessary for the aperture-based experiment to indicate the direction of free fall acceleration of antimatter, provided that antihydrogen is produced within a sufficiently small antiproton plasma at a temperature of 4 K.

Search for Magnetic Monopoles in Polar Volcanic Rocks

DEFF Research Database (Denmark)

Bendtz, K.; Milstead, D.; Hächler, H. -P.

2013-01-01

following the passage of igneous rock samples through a SQUID-based magnetometer. A total of 24.6 kg of rocks from various selected sites, among which 23.4 kg are mantle-derived rocks from the Arctic and Antarctic areas, was analyzed. No monopoles were found, and a 90% confidence level upper limit of 9.8 x...

On the CO2 Wettability of Reservoir Rocks: Addressing Conflicting Information

Science.gov (United States)

Garing, C.; Wang, S.; Tokunaga, T. K.; Wan, J.; Benson, S. M.

2017-12-01

Conventional wisdom is that siliclastic rocks are strongly water wet for the CO2-brine system, leading to high irreducible water saturation, moderate residual gas trapping and implying that tight rocks provide efficient seals for buoyant CO2. If the wetting properties become intermediate or CO2 wet, the conclusions regarding CO2 flow and trapping could be very different. Addressing the CO2 wettability of seal and reservoir rocks is therefore essential to predict CO2 storage in geologic formation. Although a substantial amount of work has been dedicated to the topic, contact angle data show a large variability and experiments on plates, micromodels and cores report conflicting results regarding the influence of supercritical CO2 (scCO2) exposure on wetting properties: whereas some experimental studies suggest dewetting upon reaction with scCO2, some others observe no wettability alteration under reservoir scCO2 conditions. After reviewing evidences for and against wettability changes associated with scCO2, we discuss potential causes for differences in experimental results. They include the presence of organic matter and impact of sample treatment, the type of media (non consolidated versus real rock), experimental time and exposure to scCO2, and difference in measurement system (porous plate versus stationary fluid method). In order to address these points, new scCO2/brine drainage-imbibition experiments were conducted on a same Berea sandstone rock core, first untreated, then fired and finally exposed to scCO2 for three weeks, using the stationary fluid method. The results are compared to similar experiments performed on quartz sands, untreated and then baked, using the porous plate method. In addition, a comparative experiment using the same Idaho gray sandstone rock core was performed with both the porous plate and the stationary fluid methods to investigate possible method-dependent results.

An integrated rock-magnetic and geochemical approach to loess/paleosol sequences from Bohemia and Moravia (Czech Republic): Implications for the Upper Pleistocene paleoenvironment in central Europe

Czech Academy of Sciences Publication Activity Database

Hošek, J.; Hambach, U.; Lisá, Lenka; Matys Grygar, Tomáš; Horáček, I.; Meszner, S.; Knésl, I.

2015-01-01

Roč. 418, 15 January (2015), s. 344-358 ISSN 0031-0182 Institutional support: RVO:67985831 ; RVO:61388980 Keywords : loess/paleosols sequences * rock-magnetism * geochemical proxies * Upper Pleistocene * paleoclimate * Central Europe Subject RIV: DB - Geology ; Mineralogy; DD - Geochemistry (UACH-T) Impact factor: 2.525, year: 2015

Hydrogeological Characterization of the Upper Camp Bird III Rock Glacier in the San Juan Mountains, Colorado Using Electromagnetic Induction

Science.gov (United States)

Granados-Aguilar, R.; Giardino, J. R.; Everett, M. E.; Pondthai, P.; Ramsey, C. E.; Mmasa, D.; Witek, M.; Rodriguez, R.

2017-12-01

Global change is the set of variations in environmental conditions that significantly impact the Earth systems. Climate, sea level, land-use/land-cover, and atmospheric composition changes are the most recognized environmental global changes. Impacts of climatic variability can include decreased rainfall, snowpack, shorter snow seasons, and changes in the timing, frequency, and intensity of precipitation events in some areas of the world, whereas other regions can suffer from the opposite effects leading to events such as landslides, flooding and extraordinary snowfall. The proposed research intends to provide a characterization of the internal structure, including water storages, pathways, and thresholds, as well as an estimation of the volume of ice stored within a rock glacier to evaluate its potential as a freshwater resources. The area of study corresponds to the third level of Camp Bird Mine in Ouray, Colorado. The tongue-shaped active rock glacier of interest, Upper Camp Bird III, has not been previously studied in detail. The predominant lithologies in the study area are Mesozoic and Cenozoic. Orogenic events caused alteration of sedimentary and intrusive igneous rock as mineral rich, hydrothermal fluids deposited economically valuable minerals in the region. Traditional geological and geomorphological mapping techniques will be complemented with the use of unmanned aerial vehicles (UAV). To obtain a detailed representation of the internal structure and determine the boundaries between resistive (rocks, sediment, and ice) and conductive materials (water and ore deposits) of the rock glacier, time-domain and frequency-domain methods will be implemented. The G-TEM by Geonics Ltd. is an innovative controlled-source time-domain electromagnetic induction system. Using the G-TEM, the distribution of electrical conductivity in the subsurface can be mapped in order to characterize the internal structure of the rock glacier from 5-10 m depth and below. The EM

Sr-Nd isotope systematics of xenoliths in Cenozoic volcanic rocks from SW Japan

International Nuclear Information System (INIS)

Kagami, Hiroo; Iwata, Masatoshi; Iizumi, Shigeru; Nureki, Terukazu.

1993-01-01

Based on new and previously published Sr and Nd isotope data, we examined the petrogenetic relationship between deep crust- and upper mantle-derived xenoliths contained in Cenozoic volcanic rocks and Cretaceous-Paleogene granitoid rocks in SW Japan. The deep crust- and upper mantle-derived mafic to ultramafic xenoliths contained in Cenozoic volcanic rocks from SW Japan have comparable initial Sr and Nd isotope ratios to the Cretaceous-Paleogene granitoid rocks in their respective districts. This may suggest that these xenoliths were genetically related to the Cretaceous-Paleogene granitoid rocks in SW Japan, and that regional variations in Sr and Nd isotope ratios observed in the granitoid rocks are attributed to differences in the geochemistry of the magma sources. (author)

Monitoring of Pre-Load on Rock Bolt Using Piezoceramic-Transducer Enabled Time Reversal Method.

Science.gov (United States)

Huo, Linsheng; Wang, Bo; Chen, Dongdong; Song, Gangbing

2017-10-27

Rock bolts ensure structural stability for tunnels and many other underground structures. The pre-load on a rock bolt plays an important role in the structural reinforcement and it is vital to monitor the pre-load status of rock bolts. In this paper, a rock bolt pre-load monitoring method based on the piezoceramic enabled time reversal method is proposed. A lead zirconate titanate (PZT) patch transducer, which works as an actuator to generate stress waves, is bonded onto the anchor plate of the rock bolt. A smart washer, which is fabricated by sandwiching a PZT patch between two metal rings, is installed between the hex nut and the anchor plate along the rock bolt. The smart washer functions as a sensor to detect the stress wave. With the increase of the pre-load values on the rock bolt, the effective contact surface area between the smart washer and the anchor plate, benefiting the stress wave propagation crossing the contact surface. With the help of time reversal technique, experimental results reveal that the magnitude of focused signal clearly increases with the increase of the pre-load on a rock bolt before the saturation which happens beyond a relatively high value of the pre-load. The proposed method provides an innovative and real time means to monitor the pre-load level of a rock bolt. By employing this method, the pre-load degradation process on a rock bolt can be clearly monitored. Please note that, currently, the proposed method applies to only new rock bolts, on which it is possible to install the PZT smart washer.

Tectonic control in source rock maturation and oil migration in Trinidad

Energy Technology Data Exchange (ETDEWEB)

Persad, K.M.; Talukdar, S.C.; Dow, W.G. (DGSI, The Woodlands, TX (United States))

1993-02-01

Oil accumulation in Trinidad were sourced by the Upper Cretaceous calcareous shales deposited along the Cretaceous passive margin of northern South America. Maturation of these source rocks, oil generation, migration and re-migration occurred in a foreland basin setting that resulted from interaction between Caribbean and South American plates during Late Oligocene to recent times. During Middle Miocene-Recent times, the foreland basin experienced strong compressional events, which controlled generation, migration, and accumulation of oil in Trinidad. A series of mature source rock kitchens formed in Late Miocene-Recent times in the Southern and Colombus Basins to the east-southeast of the Central Range Thrust. This thrust and associated fratured developed around 12 m.y.b.p. and served as vertical migration paths for the oil generated in Late Miocene time. This oil migrated into submarine fans deposited in the foreland basin axis and older reservoirs deformed into structural traps. Further generation and migration of oil, and re-migration of earlier oil took place during Pliocene-Holocene times, when later thrusting and wrench faulting served as vertical migration paths. Extremely high sedimentation rates in Pliocene-Pleistocene time, concurrent with active faulting, was responsible for very rapid generation of oil and gas. Vertically migrating gas often mixed with earlier migrated oil in overlying reservoirs. This caused depletion of oil in light hydrocarbons with accompanied fractionation among hydrocarbon types resulting in heavier oil in lower reservoirs, enrichment of light hydrocarbons and accumulation of gas-condensates in upper reservoirs. This process led to an oil-gravity stratification within about 10,000 ft of section.

Experimental investigation of the unsteady one-phase flow through perforated plates

International Nuclear Information System (INIS)

Casadei, F.

1982-07-01

The flow of the coolant through the perforated dip-plate during a hypothetical core-disruptive accident in a sodium-cooled fast breeder reactor was simulated in a one-dimensional model. Several experiments with water as fluid and with various perforation ratios of the dip-plate and different initial heights of the fluid head over the dip plate were run. The pressure drop through the dip-plate and the forces acting on the dip-plate and on the upper plug of the reactor vessel in a wide range of the Reynolds and Strouhal numbers were measured. The flow pattern downstreams the perforated plate was filmed with high-speed cameras. The resistance coefficients for the unsteady flow of the coolant through the perforated plate were obtained as a function of the acceleration. The forces acting on the upper plug and their time integral were compared with those acting on the dip-plate. Finally, using the high-speed film pictures the formation of fluid jets downstream the dip-plate was investigated. (orig.) [de

Proceedings of steam generator sludge deposition in recirculating and once through steam generator upper tube bundle and support plates

International Nuclear Information System (INIS)

Baker, R.L.; Harvego, E.A.

1992-01-01

The development of remedial measures of shot peening have given nuclear utilities viable measures to address primary water stress corrosion cracking to extend steam generator life. The nuclear utility industry is now faced with potential replacement of steam generators in nuclear power plants due to stress corrosion cracking and intergranular attach in crevice locations on the secondary side of steam generators at tube support plates and at the crevice at the top of the tube sheet. Significant work has been done on developing and understanding of the effects of sludge buildup on the corrosion process at these locations. This session was envisioned to provide a forum for the development of an understanding of the mechanisms which control the transport and deposition of sludge on the secondary side of steam generators. It is hoped that this information will aid utilities in monitoring the progression of fouling of these crevices by further knowledge in where to look for the onset of support plate crevice fouling. An understanding of the progression of fouling from upper tube support plates to those lower in the steam generator where higher temperatures cause the corrosion process to initiate first can aid the nuclear utility industry in developing remedial measures for this condition and in providing a forewarning of when to apply such remedial measures

The origin of volcanic rock fragments in Upper Pliocene Grad Member of the Mura Formation, North-Eastern Slovenia

Directory of Open Access Journals (Sweden)

Polona Kralj

2006-12-01

Full Text Available Fresh-water, coarse-grained and detritus-dominated Mura Formation in North Eastern Slovenia includes pyroclastic and volcaniclastic deposits originating from Upper Pliocene volcanic activity of basaltic geochemical character. Although localized in occurrence at the hamlet Grad, these pyroclastic and volcaniclastic sediments forma distinctive depositional unit, for which the term “Grad Member” is proposed and introduced in this paper.In the Grad area no lavas or cinder cones are preserved, and the origin of volcaniclastic fragments still uncertain. For this reason, chemical composition of basaltic rock fragments from the Grad Member volcaniclastics has been studied and compared with basaltic rocks from the neighboring locations at Klöch, Kindsberg, Dölling and Neuhaus. The Grad Member pyroclastic and volcaniclastic deposits seem to be fed from the same source which is different from the occurrences in Austria. That supports the idea about the existence of a local volcanic centre in the present Grad area. The old volcanic edificeswerepossiblydestroyed by the late-stage hydrovolcanic eruptions, and pyroclastic and volcaniclastic deposits subjected to constant reworking by fluvial currents in a dynamic sedimentary environment of alluvial fan and braided river systems.

Stratigraphical sequence and geochronology of the volcanic rock series in caifang basin, south jiangxi

International Nuclear Information System (INIS)

Xu Xunsheng; Wu Jianhua

2010-01-01

The late Mesozoic volcanic rocks in Jiangxi constitute two volcanic belts: the northern is Xiajiang-Guangfeng volcanic belt, the volcanic rocks series belong to one volcano cycle and named Wuyi group which is subdivided into three formations (Shuangfengling formation, Ehuling formation and Shixi formation); the southern is Sannan-Xunwu volcanic belt, the volcanic rocks series in Caifang basin which locates on Sannan-Xunwu volcanic belt also belong to only one volcano cycle. It can be subdivided into two lithology and lithofacies units (upper and lower): the lower unit consists of sedimentary rocks and associated with a subordinate amount of volcanic rocks, it belongs to erupt-deposit facies which is the product of early volcanic stage; the upper unit is mostly composed of volcanic rocks, it belongs to erupt facies that is the volcanic eruption product. SHRIMP zircon U-Pb age of rhyolite? which locates at the top of the upper unit is 130.79 ± 0.73) Ma. According to the new International Stratigraphic Chart, the boundary of Jurassic and Cretaceous is (145.4 ± 4.0) Ma, so the age shows that the geologic period of Caifang volcanic rocks series is early Early Cretaceous epoch. On the basis of lithological correlation, lithofacies and stratigraphic horizon analysis, the volcanic rock series in Caifang basin fall under Wuyi group, and the lower unit could be incorporated into Shuangfengling formation, the upper unit could be incorporated into Ehuling formation. The subdivision of sequence and the determination of geochronology of the volcanic rock series in Caifang basin provide some references for the study of the late Mesozoic volcanic rocks series of the Sannan-Xunwu volcanic belt. (authors)

Favorability for uranium in tertiary sedimentary rocks, southwestern Montana

International Nuclear Information System (INIS)

Wopat, M.A.; Curry, W.E.; Robins, J.W.; Marjaniemi, D.K.

1977-10-01

Tertiary sedimentary rocks in the basins of southwestern Montana were studied to determine their favorability for potential uranium resources. Uranium in the Tertiary sedimentary rocks was probably derived from the Boulder batholith and from silicic volcanic material. The batholith contains numerous uranium occurrences and is the most favorable plutonic source for uranium in the study area. Subjective favorability categories of good, moderate, and poor, based on the number and type of favorable criteria present, were used to classify the rock sequences studied. Rocks judged to have good favorability for uranium deposits are (1) Eocene and Oligocene strata and undifferentiated Tertiary rocks in the western Three Forks basin and (2) Oligocene rocks in the Helena basin. Rocks having moderate favorability consist of (1) Eocene and Oligocene strata in the Jefferson River, Beaverhead River, and lower Ruby River basins, (2) Oligocene rocks in the Townsend and Clarkston basins, (3) Miocene and Pliocene rocks in the Upper Ruby River basin, and (4) all Tertiary sedimentary formations in the eastern Three Forks basin, and in the Grasshopper Creek, Horse Prairie, Medicine Lodge Creek, Big Sheep Creek, Deer Lodge, Big Hole River, and Bull Creek basins. The following have poor favorability: (1) the Beaverhead Conglomerate in the Red Rock and Centennial basins, (2) Eocene and Oligocene rocks in the Upper Ruby River basin, (3) Miocene and Pliocene rocks in the Townsend, Clarkston, Smith River, and Divide Creek basins, (4) Miocene through Pleistocene rocks in the Jefferson River, Beaverhead River, and Lower Ruby River basins, and (5) all Tertiary sedimentary rocks in the Boulder River, Sage Creek, Muddy Creek, Madison River, Flint Creek, Gold Creek, and Bitterroot basins

Coping with the cold: an ecological context for the abundance and distribution of rock sandpipers during winter in upper Cook Inlet, Alaska

Science.gov (United States)

Ruthrauff, Daniel R.; Gill, Robert E.; Tibbitts, T. Lee

2013-01-01

Shorebirds are conspicuous and abundant at high northern latitudes during spring and summer, but as seasonal conditions deteriorate, few remain during winter. To the best of our knowledge, Cook Inlet, Alaska (60.6˚ N, 151.6˚ W), is the world’s coldest site that regularly supports wintering populations of shorebirds, and it is also the most northerly nonbreeding location for shorebirds in the Pacific Basin. During the winters of 1997–2012, we conducted aerial surveys of upper Cook Inlet to document the spatial and temporal distribution and number of Rock Sandpipers (Calidris ptilocnemis) using the inlet. The average survey total was 8191 ± 6143 SD birds, and the average of each winter season’s highest single-day count was 13 603 ± 4948 SD birds. We detected only Rock Sandpipers during our surveys, essentially all of which were individuals of the nominate subspecies (C. p. ptilocnemis). Survey totals in some winters closely matched the population estimate for this subspecies, demonstrating the region’s importance as a nonbreeding resource to the subspecies. Birds were most often found at only a handful of sites in upper Cook Inlet, but shifted their distribution to more southerly locations in the inlet during periods of extreme cold. Two environmental factors allow Rock Sandpipers to inhabit Cook Inlet during winter: 1) an abundant bivalve (Macoma balthica) food source and 2) current and tidal dynamics that keep foraging substrates accessible during all but extreme periods of cold and ice accretion. C. p. ptilocnemis is a subspecies of high conservation concern for which annual winter surveys may serve as a relatively inexpensive population-monitoring tool that will also provide insight into adaptations that allow these birds to exploit high-latitude environments in winter.

Heat production in granitic rocks

DEFF Research Database (Denmark)

Artemieva, Irina; Thybo, Hans; Jakobsen, Kiki

2017-01-01

Granitic rocks play special role in the dynamics and evolution of the Earth and its thermal regime. First, their compositional variability, reflected in the distribution of concentrations of radiogenic elements, provides constraints on global differentiation processes and large scale planetary...... evolution, where emplacement of granites is considered a particularly important process for the formation of continental crust. Second, heat production by radioactive decay is among the main heat sources in the Earth. Therefore knowledge of heat production in granitic rocks is pivotal for thermal modelling...... of the continental lithosphere, given that most radiogenic elements are concentrated in granitic rocks of the upper continental crust whereas heat production in rocks of the lower crust and lithospheric mantle is negligible. We present and analyze a new global database GRANITE2017 (with about 500 entries...

Low upper-shelf toughness, high transition temperature test insert in HSST [Heavy Section Steel Technology] PTSE-2 [Pressurized Thermal Shock Experiment-2] vessel and wide plate test specimens: Final report

International Nuclear Information System (INIS)

Domian, H.A.

1987-02-01

A piece of A387, Grade 22 Class 2 (2-1/4 Cr - 1 Mo) steel plate specially heat treated to produce low upper-shelf (LUS) toughness and high transition temperature was installed in the side wall of Heavy Section Steel Technology (HHST) vessel V-8. This vessel is to be tested by the Oak Ridge National Laboratory (ORNL) in the Pressurized Thermal Shock Experiment-2 (PTSE-2) project of the HSST program. Comparable pieces of the plate were made into six wide plate specimens and other samples. These samples underwent tensile tests, Charpy tests, and J-integral tests. The results of these tests are given in this report

Paleomagnetism of Jurassic and Cretaceous rocks in central Patagonia: a key to constrain the timing of rotations during the breakup of southwestern Gondwana?

Science.gov (United States)

Geuna, Silvana E.; Somoza, Rubén; Vizán, Haroldo; Figari, Eduardo G.; Rinaldi, Carlos A.

2000-08-01

A paleomagnetic study in Jurassic and Cretaceous rocks from the Cañadón Asfalto basin, central Patagonia, indicates the occurrence of about 25-30° clockwise rotation in Upper Jurassic-lowermost Cretaceous rocks, whereas the overlying mid-Cretaceous rocks do not show evidence of rotation. This constrains the tectonic rotation to be related to a major regional unconformity in Patagonia, which in turn seems to be close in time with the early opening of the South Atlantic Ocean. The sense and probably the timing of this rotation are similar to those of other paleomagnetically detected rotations in different areas of southwestern Gondwana, suggesting a possible relationship between these and major tectonic processes related with fragmentation of the supercontinent. On the other hand, the mid-Cretaceous rocks in the region yield a paleopole located at Lat. 87° South, Long. 159° East, A95=3.8°. This pole position is consistent with coeval high-quality paleopoles of other plates when transferred to South American coordinates, implying it is an accurate determination of the Aptian (circa 116 Ma) geomagnetic field in South America.

Wear plates control rod guide tubes top internal reactor vessel C. N. VANDELLOS II

International Nuclear Information System (INIS)

2010-01-01

The guide tubes for control rods forming part of the upper internals of the reactor vessel, its function is to guide the control rod to permit its insertion in the reactor core. These guide tubes are suspended from the upper support plate which are fixed by bolts and extending to the upper core plate which is fastened by clamping bolts (split pin) to prevent lateral displacement of the guide tubes, while allowing axial expansion.

Subduction Drive of Plate Tectonics

Science.gov (United States)

Hamilton, W. B.

2003-12-01

Don Anderson emphasizes that plate tectonics is self-organizing and is driven by subduction, which rights the density inversion generated as oceanic lithosphere forms by cooling of asthenosphere from the top. The following synthesis owes much to many discussions with him. Hinge rollback is the key to kinematics, and, like the rest of actual plate behavior, is incompatible with bottom-up convection drive. Subduction hinges (which are under, not in front of, thin leading parts of arcs and overriding plates) roll back into subducting plates. The Pacific shrinks because bounding hinges roll back into it. Colliding arcs, increasing arc curvatures, back-arc spreading, and advance of small arcs into large plates also require rollback. Forearcs of overriding plates commonly bear basins which preclude shortening of thin plate fronts throughout periods recorded by basin strata (100 Ma for Cretaceous and Paleogene California). This requires subequal rates of advance and rollback, and control of both by subduction. Convergence rate is equal to rates of rollback and advance in many systems but is greater in others. Plate-related circulation probably is closed above 650 km. Despite the popularity of concepts of plumes from, and subduction into, lower mantle, there is no convincing evidence for, and much evidence against, penetration of the 650 in either direction. That barrier not only has a crossing-inhibiting negative Clapeyron slope but also is a compositional boundary between fractionated (not "primitive"), sluggish lower mantle and fertile, mobile upper mantle. Slabs sink more steeply than they dip. Slabs older than about 60 Ma when their subduction began sink to, and lie down on and depress, the 650-km discontinuity, and are overpassed, whereas younger slabs become neutrally buoyant in mid-upper mantle, into which they are mixed as they too are overpassed. Broadside-sinking old slabs push all upper mantle, from base of oceanic lithosphere down to the 650, back under

Hydrologic properties and ground-water flow systems of the Paleozoic rocks in the upper Colorado River basin in Arizona, Colorado, New Mexico, Utah, and Wyoming, excluding the San Juan Basin

Science.gov (United States)

Geldon, Arthur L.

2003-01-01

The hydrologic properties and ground-water flow systems of Paleozoic sedimentary rocks in the Upper Colorado River Basin were investigated under the Regional Aquifer-System Analysis (RASA) program of the U.S. Geological Survey in anticipation of the development of water supplies from bedrock aquifers to fulfill the region's growing water demands. The study area, in parts of Arizona, Colorado, New Mexico, Utah, and Wyoming, covers about 100,000 square miles. It includes parts of four physiographic provinces--the Middle Rocky Mountains, Wyoming Basin, Southern Rocky Mountains, and Colorado Plateaus. A variety of landforms, including mountains, plateaus, mesas, cuestas, plains, badlands, and canyons, are present. Altitudes range from 3,100 to 14,500 feet. Precipitation is distributed orographically and ranges from less than 6 inches per year at lower altitudes to more than 60 inches per year in some mountainous areas. Most of the infrequent precipitation at altitudes of less than 6,000 feet is consumed by evapotranspiration. The Colorado and Green Rivers are the principal streams: the 1964-82 average discharge of the Colorado River where it leaves the Upper Colorado River Basin is 12,170 cubic feet per second (a decrease of 5,680 cubic feet per second since construction of Glen Canyon Dam in 1963). On the basis of their predominant lithologic and hydrologic properties, the Paleozoic rocks are classified into four aquifers and three confining units. The Flathead aquifer, Gros Ventre confining unit, Bighorn aquifer, Elbert-Parting confining unit, and Madison aquifer (Redwall-Leadville and Darwin-Humbug zones) make up the Four Corners aquifer system. A thick sequence, composed mostly of Mississippian and Pennsylvanian shale, anhydrite, halite, and carbonate rocks--the Four Corners confining unit (Belden-Molas and Paradox-Eagle Valley subunits)--overlies the Four Corners aquifer system in most areas and inhibits vertical ground-water flow between the Four Corners aquifer

Spirit Beside 'Home Plate,' Sol 1809

Science.gov (United States)

2009-01-01

NASA Mars Exploration Rover Spirit used its navigation camera to take the images assembled into this 120-degree view southward after a short drive during the 1,809th Martian day, or sol, of Spirit's mission on the surface of Mars (February 3, 2009). Spirit had driven about 2.6 meters (8.5 feet) that sol, continuing a clockwise route around a low plateau called 'Home Plate.' In this image, the rocks visible above the rovers' solar panels are on the slope at the northern edge of Home Plate. This view is presented as a cylindrical projection with geometric seam correction.

Cenozoic intraplate tectonics in Central Patagonia: Record of main Andean phases in a weak upper plate

Science.gov (United States)

Gianni, G. M.; Echaurren, A.; Folguera, A.; Likerman, J.; Encinas, A.; García, H. P. A.; Dal Molin, C.; Valencia, V. A.

2017-11-01

Contraction in intraplate areas is still poorly understood relative to similar deformation at plate margins. In order to contribute to its comprehension, we study the Patagonian broken foreland (PBF) in South America whose evolution remains controversial. Time constraints of tectonic events and structural characterization of this belt are limited. Also, major causes of strain location in this orogen far from the plate margin are enigmatic. To unravel tectonic events, we studied the Cenozoic sedimentary record of the central sector of the Patagonian broken foreland (San Bernardo fold and thrust belt, 44°30‧S-46°S) and the Andes (Meseta de Chalia, 46°S) following an approach involving growth-strata detection, U-Pb geochronology and structural modeling. Additionally, we elaborate a high resolution analysis of the effective elastic thickness (Te) to examine the relation between intraplate contraction location and variations in lithospheric strength. The occurrence of Eocene growth-strata ( 44-40 Ma) suggests that contraction in the Andes and the Patagonian broken foreland was linked to the Incaic phase. Detection of synextensional deposits suggests that the broken foreland collapsed partially during Oligocene to early Miocene. During middle Miocene times, the Quechua contractional phase produced folding of Neogene volcanic rocks and olistostrome deposition at 17 Ma. Finally, the presented Te map shows that intraplate contraction related to Andean phases localized preferentially along weak lithospheric zones (Te < 15 km). Hence, the observed strain distribution in the PBF appears to be controlled by lateral variations in the lithospheric strength. Variations in this parameter could be related to thermo-mechanical weakening produced by intraplate rifting in Paleozoic-Mesozoic times.

TL studies of calcareous rocks of Danta area, North Gujarat

International Nuclear Information System (INIS)

Limaye, M.A.; Desai, S.J.; Murthy, K.V.R.; Joshi, T.R.

1992-01-01

The lithounits exposed around Danta in Banaskantha district of North Gujarat belong to Ajabgarh Group, the upper division of the Delhi super group. These rocks are intruded by syn to late kinematic basic rocks and by Erinpura granites of post Delhi age. The Ajabgarh group consists of pelitic and calcareous components. Mineralogically the pelitic rocks comprise cordierite, almandine garnet, k-feldspar, sillimanite, quartz and mica in variable proportions. The calcareous rocks are seen to contain dominantly calcite, scapolite, forsterite, sphene, k-feldspar. These mineral assemblages correspond to upper Amphibolite to lower Granulite facies of regional metamorphism. The chemistry of the calcareous rocks show predominance of CaO over MgO. The glow curves obtained from virgin samples (NTL) as well as artificial beta irradiated indicate glow peaks at 140 o C, 290 o C, 310 o C and 390 o C. The TL glow peak temperatures are in general agreement with those reported by Borsi and Rinaldi and Medlin. The pronounced peak at 390 o C and 290 o C are suggestive of their high irradiation sensitivity and also probably reflect variation in the Mn content of the rocks. (author). 9 refs., 16 tabs., 2 figs

Rocks and geology in the San Francisco Bay region

Science.gov (United States)

Stoffer, Philip W.

2002-01-01

The landscape of the San Francisco Bay region is host to a greater variety of rocks than most other regions in the United States. This introductory guide provides illustrated descriptions of 46 common and important varieties of igneous, sedimentary, and metamorphic rock found in the region. Rock types are described in context of their identification qualities, how they form, and where they occur in the region. The guide also provides discussion about of regional geology, plate tectonics, the rock cycle, the significance of the selected rock types in relation to both earth history and the impact of mineral resources on the development in the region. Maps and text also provide information where rocks, fossils, and geologic features can be visited on public lands or in association with public displays in regional museums, park visitor centers, and other public facilities.

Continued Trenchward Procession of Upper Plate GPS Sites Following the 2012 Mw 7.6 Nicoya Earthquake

Science.gov (United States)

Hobbs, T. E.; Newman, A. V.; Protti, M.

2015-12-01

When studying subduction zone deformation one is often forced to consider a region significantly landward of the trench. The Nicoya Peninsula in Costa Rica presents a unique opportunity to obtain rich datasets from land in relatively close proximity to an active megathrust. A recent moment magnitude (Mw) 7.6 earthquake in September 2012 on this portion of the Middle America Trench affords an opportunity to constrain the ongoing postseismic deformation on the subduction interface between the Cocos and Caribbean plates. GPS campaigns occupying 22 sites were undertaken immediately following the earthquake in September-December 2012 and most recently in March 2015. Combined with data from a network of 17 continuous GPS in the region, we analyze the spatial and temporal changes in the postseismic velocity field. Another campaign is planned for 2017, in conjunction with our ongoing analysis of the continuous GPS network. After 2.5 years, campaign GPS results indicate significant trenchward motion of at least 7 cm, relative to a fixed Caribbean plate, for all sites up to the volcanic chain. Maximum values of 22 cm are observed above and updip of the coseismic rupture zone. The trench-parallel component of the displacement field is small, with few deviations between sites. Together these observations are substantially more self-similar over a larger region than what was observed for the coseismic offset. This implies that there may be a low stress differential across the upper plate, suggesting that the subduction interface environment, including the mainshock and surrounding area, has remained relatively weak following the earthquake. By utilizing a dense and long-term geodetic network we will report on initial modeling that aims to characterize the evolution of afterslip. The effect of regional aftershocks, including an Mw 6.5 in October 2012, and viscoelastic mantle relaxation will be considered to establish the necessity of such effects in robustly accounting for

Modeling and Simulation of Nonlinear Micro-electromechanical Circular Plate

Directory of Open Access Journals (Sweden)

Chin-Chia Liu

2013-09-01

Full Text Available In the present study, the hybrid differential transformation and finite difference method is applied to analyze the dynamic behavior of the nonlinear micro-electromechanical circular plate actuated by combined DC / AC loading schemes. The analysis takes account of the axial residual stress and hydrostatic pressure acting on micro circular plate upper surface. The dynamic response of the plate as a function of the magnitude of the AC driving voltage is explored. Moreover, the effect of the initial gap height on the pull-in voltage of the plate is systematically explored.

Reconstruction of large upper eyelid defects with a free tarsal plate graft and a myocutaneous pedicle flap plus a free skin graft

DEFF Research Database (Denmark)

Toft, Peter B

2016-01-01

skin graft. RESULTS: All patients healed without necrosis, did not suffer from lagophthalmos, achieved reasonable cosmesis, and did not need lubricants. In one patient, a contact lens was necessary for three weeks because of corneal erosion. One patient still needs a contact lens 3 months after...... excision to avoid eye discomfort. CONCLUSION: Large upper eyelid defects can be reconstructed with a free tarsal plate graft and a laterally based myocutaneous pedicle flap in combination with a free skin graft. Two-step procedures can probably be avoided in most cases....

Nd and Sr isotopic variations in acidic rocks from Japan: significance of upper-mantle heterogeneity

Science.gov (United States)

Terakado, Yasutaka; Nakamura, Noboru

1984-10-01

Initial Nd and Sr isotopic ratios have been measured for Cretaceous acidic and related intermediate rocks (24 volcanic and two plutonic rocks) from the Inner Zone of Southwest Japan (IZSWJ) to investigate the genesis of acidic magmas. The initial Nd and Sr isotopic ratios for these rocks show three interesting features: (1) ɛ Nd values for acidic rocks (+2 to -9) are negatively correlated with ɛ Sr values (+10 to +90) together with those for intermediate rocks ( ɛ Nd=+3 to -8; ɛ Sr=0 to +65). (2) The ɛ Nd values for silica rich rocks (>60% SiO2) correlate with the longitude of the sample locality, decreasing from west to east in a stepwise fashion: Four areas characterized by uniform ɛ Nd values are discriminated. (3) Low silica rocks (Japan suggest that the acidic rocks can be formed neither by fractional crystallization processes from more basic magmas nor by crustal assimilation processes. The isotopic variations of the acidic rocks may reflect regional isotopic heterogeneity in the lower crust, and this heterogeneity may ultimately be attributed to the regional heterogeneity of the uppermost-mantle beneath the Japanese Islands.

The upper crust laid on its side: tectonic implications of steeply tilted crustal slabs for extension in the basin and range

Science.gov (United States)

Howard, Keith A.

2005-01-01

Tilted slabs expose as much as the top 8–15 km of the upper crust in many parts of the Basin and Range province. Exposures of now-recumbent crustal sections in these slabs allow analysis of pre-tilt depth variations in dike swarms, plutons, and thermal history. Before tilting the slabs were panels between moderately dipping, active Tertiary normal faults. The slabs and their bounding normal faults were tilted to piggyback positions on deeper footwalls that warped up isostatically beneath them during tectonic unloading. Stratal dips within the slabs are commonly tilted to vertical or even slightly overturned, especially in the southern Basin and Range where the thin stratified cover overlies similarly tilted basement granite and gneiss. Some homoclinal recumbent slabs of basement rock display faults that splay upward into forced folds in overlying cover sequences, which thereby exhibit shallower dips. The 15-km maximum exposed paleodepth for the slabs represents the base of the brittle upper crust, as it coincides with the depth of the modern base of the seismogenic zone and the maximum focal depths of large normal-fault earthquakes in the Basin and Range. Many upended slabs accompany metamorphic core complexes, but not all core complexes have corresponding thick recumbent hanging-wall slabs. The Ruby Mountains core complex, for example, preserves only scraps of upper-plate rocks as domed-up extensional klippen, and most of the thick crustal section that originally overlay the uplifted metamorphic core now must reside below little-tilted hanging-wall blocks in the Elko-Carlin area to the west. The Whipple and Catalina Mountains core complexes in contrast are footwall to large recumbent hanging-wall slabs of basement rock exposing 8-15 km paleodepths that originally roofed the metamorphic cores; the exposed paleodepths require that a footwall rolled up beneath the slabs.

Baking process of thin plate carbonaceous compact

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Yoshio; Shimada, Toyokazu

1987-06-27

As a production process of a thin plate carbonaceous compact for separator of phosphoric acid fuel cell, there is a process to knead carbonaceous powder and thermosetting resin solution, to form and harden the kneaded material and then to bake, carbonize and graphitize it. However in this baking and carbonization treatment, many thin plate compacts are set in a compiled manner within a heating furnace and receive a heat treatment from their circumference. Since the above compacts to be heated tend generally to be heated from their peripheries, their baked conditions are not homogeneous easily causing the formation of cracks, etc.. As a process to heat and bake homogeneously by removing the above problematical points, this invention offers a process to set in a heating furnace a laminate consisting of the lamination of thin plate carbonaceous compacts and the heat resistant soaking plates which hold the upper and lower ends of the above lamination, to fill the upper and under peripheries of the laminate above with high heat conductive packing material and its side periphery with low heat conductive packing material respectively and to heat and sinter it. In addition, the invention specifies the high and low heat conductive packing materials respectively. (1 fig, 2 tabs)

Frictional sliding in layered rock model: Preliminary experiments. Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Perry, K.E. Jr.; Buescher, B.J.; Anderson, D.; Epstein, J.S.

1995-09-01

An important aspect of determining the suitability of Yucca Mountain as a possible nuclear waste repository requires understanding the mechanical behavior of jointed rock-masses. To this end we have studied the frictional sliding between simulated rock joints in the laboratory using the technique of phase shifting moire interferometry. The models were made from stacks of Lexan plates and contained a central hole to induce slip between the plates when the models were loaded in compression. These preliminary results confirm the feasibility of the approach and show a clear evolution of slip as function of load

Thermal Stress Cracking of Slide-Gate Plates in Steel Continuous Casting

Science.gov (United States)

Lee, Hyoung-Jun; Thomas, Brian G.; Kim, Seon-Hyo

2016-04-01

The slide-gate plates in a cassette assembly control the steel flow through the tundish nozzle, and may experience through-thickness cracks, caused by thermal expansion and/or mechanical constraint, leading to air aspiration and safety concerns. Different mechanisms for common and rare crack formation are investigated with the aid of a three-dimensional finite-element model of thermal mechanical behavior of the slide-gate plate assembly during bolt pretensioning, preheating, tundish filling, casting, and cooling stages. The model was validated with previous plant temperature measurements of a ladle plate during preheating and casting, and then applied to a typical tundish-nozzle slide-gate assembly. The formation mechanisms of different types of cracks in the slide-gate plates are investigated using the model and evaluated with actual slide-gate plates at POSCO. Common through-thickness radial cracks, found in every plate, are caused during casting by high tensile stress on the outside surfaces of the plates, due to internal thermal expansion. In the upper plate, these cracks may also arise during preheating or tundish filling. Excessive bolt tightening, combined with thermal expansion during casting may cause rare radial cracks in the upper and lower plates. Rare radial and transverse cracks in middle plate appear to be caused during tundish filling by impingement of molten steel on the middle of the middle plate that generates tensile stress in the surrounding refractory. The mechanical properties of the refractory, the bolt tightening conditions, and the cassette/plate design are all important to service life.

Basic rocks in Finland

International Nuclear Information System (INIS)

Piirainen, T.; Gehoer, S.; Iljina, M.; Kaerki, A.; Paakkola, J.; Vuollo, J.

1992-10-01

Basic igneous rocks, containing less than 52% SiO 2 , constitute an important part of the Finnish Archaean and Proterozoic crust. In the Archaean crust exist two units which contain the majority of the basic rocks. The Arcaean basic rocks are metavolcanics and situated in the Greenstone Belts of Eastern Finland. They are divided into two units. The greenstones of the lower one are tholeiites, komatiites and basaltic komatiites. The upper consists of bimodal series of volcanics and the basic rocks of which are Fe-tholeiites, basaltic komatiites and komatiites. Proterozoic basic rocks are divided into seven groups according to their ages. The Proterozoic igneous activity started by the volominous basic magmatism 2.44 Ga ago. During this stage formed the layered intrusions and related dykes in the Northern Finland. 2.2 Ga old basic rocks are situated at the margins of Karelian formations. 2.1 Ga aged Fe-tholeiitic magmatic activity is widespread in Eastern and Northern Finland. The basic rocks of 1.97 Ga age group are met within the Karelian Schist Belts as obducted ophiolite complexes but they occur also as tholeiitic diabase dykes cutting the Karelian schists and Archean basement. The intrusions and the volcanics of the 1.9 Ga old basic igneous activity are mostly encountered around the Granitoid Complex of Central Finland. Subjotnian, 1.6 Ga aged tholeiitic diabases are situated around the Rapakivi massifs of Southern Finland, and postjotnian, 1.2 Ga diabases in Western Finland where they form dykes cutting Svecofennian rocks

Diapir versus along-channel ascent of crustal material during plate convergence: constrained by the thermal structure of subduction zones

Science.gov (United States)

Liu, M. Q.; Li, Z. H.

2017-12-01

Crustal rocks can be subducted to mantle depths, interact with the mantle wedge, and then exhume to the crustal depth again, which is generally considered as the mechanism for the formation of ultrahigh-pressure metamorphic rocks in nature. The crustal rocks undergo dehydration and melting at subarc depths, giving rise to fluids that metasomatize and weaken the overlying mantle wedge. There are generally two ways for the material ascent from subarc depths: one is along subduction channel; the other is through the mantle wedge by diapir. In order to study the conditions and dynamics of these contrasting material ascent modes, systematic petrological-thermo-mechanical numerical models are constructed with variable thicknesses of the overriding and subducting continental plates, ages of the subducting oceanic plate, as well as the plate convergence rates. The model results suggest that the thermal structures of subduction zones control the thermal condition and fluid/melt activity at the slab-mantle interface in subcontinental subduction channels, which further strongly affect the material transportation and ascent mode. Thick overriding continental plate and low-angle subduction style induced by young subducting oceanic plate both contribute to the formation of relatively cold subduction channels with strong overriding mantle wedge, where the along-channel exhumation occurs exclusively to result in the exhumation of HP-UHP metamorphic rocks. In contrast, thin overriding lithosphere and steep subduction style induced by old subducting oceanic plate are the favorable conditions for hot subduction channels, which lead to significant hydration and metasomatism, melting and weakening of the overriding mantle wedge and thus cause the ascent of mantle wedge-derived melts by diapir through the mantle wedge. This may corresponds to the origination of continental arc volcanism from mafic to ultramafic metasomatites in the bottom of the mantle wedge. In addition, the plate

Lithofacies palaeogeography of the Late Permian Wujiaping Age in the Middle and Upper Yangtze Region, China

Directory of Open Access Journals (Sweden)

Jin-Xiong Luo

2014-10-01

Full Text Available The lithofacies palaeogeography of the Late Permian Wujiaping Age in Middle and Upper Yangtze Region was studied based on petrography and the “single factor analysis and multifactor comprehensive mapping” method. The Upper Permian Wujiaping Stage in the Middle and Upper Yangtze Region is mainly composed of carbonate rocks and clastic rocks, with lesser amounts of siliceous rocks, pyroclastic rocks, volcanic rocks and coal. The rocks can be divided into three types, including clastic rock, clastic rock–limestone and limestone–siliceous rock, and four fundamental ecological types and four fossil assemblages are recognized in the Wujiaping Stage. Based on a petrological and palaeoecological study, six single factors were selected, namely, thickness (m, content (% of marine rocks, content (% of shallow water carbonate rocks, content (% of biograins with limemud, content (% of thin-bedded siliceous rocks and content (% of deep water sedimentary rocks. Six single factors maps of the Wujiaping Stage and one lithofacies palaeogeography map of the Wujiaping Age were composed. Palaeogeographic units from west to east include an eroded area, an alluvial plain, a clastic rock platform, a carbonate rock platform where biocrowds developed, a slope and a basin. In addition, a clastic rock platform exists in the southeast of the study area. Hydrocarbon source rock and reservoir conditions were preliminarily analyzed based on lithofacies palaeogeography. Sedimentary environments have obvious controls over the development of the resource rocks. With regard to the abundance of organic matter, the hydrocarbon potential of the coastal swamp environment is the best, followed by the basin environment and the carbonate rock platform. The gas reservoir types of the Wujiaping Stage can be classified as conventional and unconventional gas reservoirs, like coal bed gas and shale gas; all of them have well exploration prospects.

Petrography of the Paleogene Volcanic Rocks of the Sierra Maestra, Southeastern Cuba

Science.gov (United States)

Bemis, V. L.

2006-12-01

This study is a petrographic analysis of over 200 specimens of the Paleogene volcanic rocks of the Sierra Maestra (Southerneastern Cuba), a key structure in the framework of the northern Caribbean plate boundary evolution. The purpose of this study is to understand the eruptive processes and the depositional environments. The volcanic sequence in the lower part of the Sierra Maestra begins with highly porphyritic pillow lavas, topped by massive tuffs and autoclastic flows. The presence of broken phenocrystals, palagonitic glass and hyaloclastites in this section of the sequence suggests that the prevalent mode of eruption was explosive. The absence of welding in the tuffs suggests that the rocks were emplaced in a deep submarine environment. Coherent flows, much less common than the massive tuffs, show evidence of autoclastic fracturing, also indicating low temperature-submarine environments. These observations support the hypothesis that the Sierra Maestra sequence may be neither part of the Great Antilles Arc of the Mesozoic nor any other fully developed volcanic arc, rather a 250 km long, submarine eruptive system of dikes, flows and sills, most likely a back-arc structure. The volcanic rocks of the upper sequence are all very fine grained, reworked volcaniclastic materials, often with the structures of distal turbidities, in mode and texture similar to those drilled on the Cayman Rise. This study suggests that the Sierra Maestra most likely records volcanism of diverse sources: a local older submarine source, and one or more distal younger sources, identifiable with the pan-Caribbean volcanic events of the Tertiary.

Jacking mechanism for upper internals structure of a liquid metal nuclear reactor

International Nuclear Information System (INIS)

Gillett, J.E.; Wineman, A.L.

1984-01-01

A jacking mechanism is described for raising the upper internals structure of a liquid metal nuclear reactor which jacking mechanism uses a system of gears and drive shafts to transmit force from a single motor to four mechanically synchronized ball jacks to raise and lower support columns which support the upper internals structure. The support columns have a pin structure which rides up and down in a slot in a housing fixed to the reactor head. The pin has two locking plates which can be rotated around the pin to bring bolt holes through the locking plates into alignment with a set of bolt holes in the housing, there being a set of such housing bolt holes corresponding to both a raised and a lowered position of the support column. When the locking plate is so aligned, a surface of the locking plate mates with a surface in the housing such that the support column is then supported by the locking plate and not by the ball jacks. Since the locking plates are to be installed and bolted to the housing during periods of reactor operation, the ball jacks need not be sized to react the large forces which occur or potentially could occur on the upper internals structure of the reactor during operation. The locking plates react these loads. The ball jacks, used only during refueling, can be smaller, which enable conventionally available equipment to fulfill the precision requirements for the task within available space

Response spectra by blind faults for design purpose of stiff structures on rock site

International Nuclear Information System (INIS)

Hiroyuki Mizutani; Kenichi Kato; Masayuki Takemura; Kazuhiko Yashiro; Kazuo Dan

2005-01-01

The goal of this paper is to propose the response spectra by blind faults for seismic design of nuclear power facilities. It is impossible to evaluate earthquake ground motions from blind faults, because the size and the location of blind fault cannot be identified even if the detailed geological surveys are conducted. From the viewpoint of seismic design, it is crucial to investigate the upper level of earthquake ground motions due to blind faults. In this paper, 41 earthquakes that occurred in the upper crust in Japan and California are selected and classified into the active and the blind fault types. On the basis of near-source strong motion records observed on rock sites, upper level of response spectra by blind faults is examined. The estimated upper level is as follows: the peak ground acceleration is 450 cm/s 2 , the flat level of the acceleration response spectra is 1200 cm/s 2 , and the flat level of the velocity response spectra is 100 cm/s on rock sites with shear wave velocity Vs of about 700 m/s. The upper level can envelop the observed response spectra in near-source region on rock sites. (authors)

Disk generator with nearly shockless accelerated driver plate

International Nuclear Information System (INIS)

Fowler, C.M.; Hoeberling, R.F.; Marsh, S.P.

1990-01-01

The disk generator, shown in this paper, was first conceived as a useful magnetic field source for a class of in situ plasma experiments. Initial current is supplied (from a capacitor bank) to the generator through radial coaxial cables. It enters the top plate, passes through the central post, and exists through the top of the outer cylindrical glide surface, which is insulated from the top plate. The explosive over the top plate is initiated simultaneously over its upper surface at such a time that the top plate starts its downward motion at about peak initial current. Several conditions were required for the experiments under consideration: the top or driver plate should contact the bottom plate nearly parallel to it; the generator interior should be evacuated; microjetting debris (fluff) arising from the driver plate should be held to a minimum; currents developed should be several tens of megamperes, with values of dI/dt exceeding 10 13 A/s

Continuous distillation of oil-bearing rocks

Energy Technology Data Exchange (ETDEWEB)

1923-11-14

A continuous process of distilling petroleum-bearing, asphaltic, or bituminous rocks to free bitumen is characterized by vaporizing hydrocarbons solid, pasty, or liquid from petroleum-containing asphaltic or bituminous rocks to free bitumen without ever reaching the temperatures at which they can produce decomposition, the necessary heat being furnished by combustion of part of the hydrocarbons of the treated rocks. A furnace for carrying out the process of claim 1 is characterized by consisting of a cavity lined inside with reflector, of variable section and with a throat at the upper part for charging the material to be treated and means for blowing the lower part of the furnace with the air necessary for combustion and inert gas for regulating the combustion and removal of the hydrocarbons.

Palaeomagnetism or Palaeomagic? Misconceptions about Rock Magnetism

Science.gov (United States)

Murphy, Phil

2016-01-01

The study and understanding of paleomagnetism has been pivotal in the development of the theory of plate tectonics. When it is taught in schools there are a number possible misconceptions that need to be addressed. This article attempts to provide an explanation of rock magnetism as well as strategies to avoid reinforcing some commonly identified…

Depositional environment and source rock potential of Cenomanian and Turonian sedimentary rocks of the Tarfaya Basin, Southwest Morocco

Energy Technology Data Exchange (ETDEWEB)

Ghassal, B.I.; Littke, R.; Sachse, V.; Sindern, S.; Schwarzbauer, J.

2016-07-01

Detailed organic and inorganic geochemical analyses were used to assess the depositional environment and source rock potential of the Cenomanian and Turonian oil shale deposits in the Tarfaya Basin. This study is based on core samples from the Tarfaya Sondage-4 well that penetrated over 300m of Mid Cretaceous organic matter-rich deposits. A total of 242 samples were analyzed for total organic and inorganic carbon and selected samples for total sulfur and major elements as well as for organic petrology, Rock-Eval pyrolysis, Curie-Point-pyrolysis-gaschromatography-Mass-Spectrometry and molecular geochemistry of solvent extracts. Based on major elements the lower Cenomanian differs from the other intervals by higher silicate and lower carbonate contents. Moreover, the molecular geochemistry suggests anoxic bottom marine water conditions during the Cenomanian-Turonian Boundary Event (CTBE; Oceanic Anoxic Event 2: OAE2). As a proxy for the Sorg/Corg ratio, the ratio total thiophenes/total benzenes compounds was calculated from pyrolysate compositions. The results suggest that Sorg/ Corg is low in the lower Cenomanian, moderate in the upper Cenomanian, very high in the CTBE (CenomanianTuronian Boundary Event) and high in the Turonian samples. Rock-Eval data reveal that the lower Cenomanian is a moderately organic carbon-rich source rock with good potential to generate oil and gas upon thermal maturation. On the other hand, the samples from the upper Cenomanian to Turonian exhibit higher organic carbon content and can be classified as oil-prone source rocks. Based on Tmax data, all rocks are thermally immature. The microscopic investigations suggest dominance of submicroscopic organic matter in all samples and different contents of bituminite and alginite. The lower Cenomanian samples have little visible organic matter and no bituminite. The upper Cenomanian and CTBE samples are poor in bituminite and have rare visible organic matter, whereas the Turonian samples change

Impact of uncertain reference-frame motions in plate kinematic reconstructions

DEFF Research Database (Denmark)

Iaffaldano, Giampiero; Stein, Seth

2017-01-01

Geoscientists infer past plate motions, which serve as fundamental constraints for a range of studies, from observations of magnetic isochrons as well as hotspots tracks on the ocean floor and, for stages older than the Cretaceous, from paleomagnetic data. These observations effectively represent...... time-integrals of past plate motions but, because they are made at present, yield plate kinematics naturally tied to a present-day reference-frame, which may be another plate or a hotspots system. These kinematics are therefore different than those occurred at the time when the rocks acquired...... – in a temporal sense – and prone to noise. This limitation is commonly perceived to hamper the correction of plate kinematic reconstructions for RFAMs, but the extent to which this may be the case has not been explored. Here we assess the impact of uncertain RFAMs on kinematic reconstructions using synthetic...

SOME INOZOID SPONGES FROM UPPER TRIASSIC (NORIAN-RHAETIAN NAYBAND FORMATION OF CENTRAL IRAN

Directory of Open Access Journals (Sweden)

BABA SENOWBARI-DARYAN

1997-11-01

Full Text Available Some small-scaled Norian-Rhaetian reefs and reef mounds are imbedded within the shales, siltstones and siliciclastic-carbonate deposits of the Nayband Formation in central Iran. These deposits belong to the central Iranian plate as part of the Cimmerian Continent. Most of the biogenic rocks have a biostromal geometry, biohermal constructions are rare. Inozoid, sphinctozoid, and chaetetid sponges are, beside of corals and other reef builders, the most important reef organisms within these bioconstructions. In some reefs a variety of hexactinellid sponges also occur. The following inozoid sponges are described in this paper: Radiofibra norica n. sp., Permocorynella maxima n. sp., ?Sestrostomella robusta, Marawandia iranica, n. gen., n. sp. and Enaulofungia? triassica n. sp. The first four taxa are among the most abundant sponges within the Nayband Formation where it is exposed in several localities in central Iran. Enaulofungia? triassica, however, is not an abundant sponge there. These inozoid sponges have never been reported from the Triassic deposits of this region. Radiofibra, until now known only from the Upper Permian of Djebel Tebaga (Tunisia, is reported here for the first time from Triassic rocks. The stratigraphic as well as the paleogeographic distribution of all the genera are discussed.   

Weathering of rock 'Ginger'

Science.gov (United States)

1997-01-01

One of the more unusual rocks at the site is Ginger, located southeast of the lander. Parts of it have the reddest color of any material in view, whereas its rounded lobes are gray and relatively unweathered. These color differences are brought out in the inset, enhanced at the upper right. In the false color image at the lower right, the shape of the visible-wavelength spectrum (related to the abundance of weathered ferric iron minerals) is indicated by the hue of the rocks. Blue indicates relatively unweathered rocks. Typical soils and drift, which are heavily weathered, are shown in green and flesh tones. The very red color in the creases in the rock surface correspond to a crust of ferric minerals. The origin of the rock is uncertain; the ferric crust may have grown underneath the rock, or it may cement pebbles together into a conglomerate. Ginger will be a target of future super-resolution studies to better constrain its origin.Mars Pathfinder is the second in NASA's Discovery program of low-cost spacecraft with highly focused science goals. The Jet Propulsion Laboratory, Pasadena, CA, developed and manages the Mars Pathfinder mission for NASA's Office of Space Science, Washington, D.C. The Imager for Mars Pathfinder (IMP) was developed by the University of Arizona Lunar and Planetary Laboratory under contract to JPL. Peter Smith is the Principal Investigator. JPL is an operating division of the California Institute of Technology (Caltech).

Primary Rock Temperature Fields in Czech and Polish Part of the Upper of the Upper Silesian Coal Basin / Pole temperatury pierwotnej skał w czeskiej i polskiej części górnośląskiego okręgu węglowego

Science.gov (United States)

Doležal, Libor; Knechtel, Józef; Taufer, Antonín; Trávníček, Ludvík

2013-03-01

Knowledge of the temperature of rock mass is no doubt of substantial meaning, both for the solution of economicaly demanding protection of mine workers in difficult microclimatic environment and for perspective usage of geothermal energy from the depth of the earth. International cooperation of our and Polish specialists is in this sense more than welcome, also because the exploitation of coal seams takes place in the same Upper Silesia rock coal basin. This profesional article is concentrated on complex analysis of temperature fields of the Ostrava- Karviná district, mainly from results of thermologging measurements in geological survey boreholes both on surface and underground, and also from the actual temperature measurements in the coal mines. One chapter of this article describes the original approach to the survey of temperature field and its prognosis in the Polish part of the Upper Silesia coal basin by a researcher from GIG Katowice. The most suitable method of analysis of primary temperature field seemed the preparation of isocurves of temperature(isothermal lines) for the existing mine working areas, even if the method of obtaining them was different. The Czech method is based on determination of the quantitative dependence of temperature on the rock mass depth from the abovementioned measurement results, calculation of geothermal gradients and the following recalculation of real temperature values for various depth levels. Then isothermal lines for these depth levels are created together with colour distingushing of their value limits. The Polish method is sufficiently described in a dedicated chapter. The conclusion of the article underlines the decisive role of the structuraly tectonic composition of the rock mass on the temperature field in the long term thermic evolution of the Earth.

2D seismic interpretation and characterization of the Hauterivian-Early Barremian source rock in Al Baraka oil field, Komombo Basin, Upper Egypt

Science.gov (United States)

Ali, Moamen; Darwish, M.; Essa, Mahmoud A.; Abdelhady, A.

2018-03-01

Komombo Basin is located in Upper Egypt about 570 km southeast of Cairo; it is an asymmetrical half graben and the first oil producing basin in Upper Egypt. The Six Hills Formation is of Early Cretaceous age and subdivided into seven members from base to top (A-G); meanwhile the B member is of Hauterivian-Early Barremian and it is the only source rock of Komombo Basin. Therefore, a detailed study of the SR should be carried out, which includes the determination of the main structural elements, thickness, facies distribution and characterization of the B member SR which has not been conducted previously in the study area. Twenty 2D seismic lines were interpreted with three vertical seismic profiles (VSP) to construct the depth structure-tectonic map on the top of the B member and to highlight the major structural elements. The interpretation of depth structure contour map shows two main fault trends directed towards the NW-SE and NE to ENE directions. The NW-SE trend is the dominant one, creating a major half-graben system. Also the depth values range from -8400 ft at the depocenter in the eastern part to -4800 ft at the shoulder of the basin in the northwestern part of the study area. Meanwhile the Isopach contour map of the B member shows a variable thickness ranging between 300 ft to 750 ft. The facies model shows that the B member SR is composed mainly of shale with some sandstone streaks. The B member rock samples were collected from Al Baraka-1 and Al Baraka SE-1 in the eastern part of Komombo Basin. The results indicate that the organic matter content (TOC) has mainly good to very good (1-3.36 wt %), The B member samples have HI values in the range 157-365 (mg HC/g TOC) and dominated by Type II/III kerogen, and is thus considered to be oil-gas prone based on Rock-Eval pyrolysis, Tmax values between 442° and 456° C therefore interpreted to be mature for hydrocarbon generation. Based on the measured vitrinite equivalent reflectance values, the B member SR

Crack-arrest behavior in SEN wide plates of low-upper-shelf base metal tested under nonisothermal conditions: WP-2 series

International Nuclear Information System (INIS)

Naus, D.J.; Keeney-Walker, J.; Bass, B.R.; Robinson, G.C. Jr.; Iskander, S.K.; Alexander, D.J.; Fields, R.J.; deWit, R.; Low, S.R.; Schwartz, C.W.

1990-08-01

The Heavy-Section Steel Technology (HSST) Program at the Oak Ridge National Laboratory under the sponsorship of the Nuclear Regulatory Commission is conducting analytical and experimental studies aimed at understanding the circumstances that would initiate the growth of an existing crack in a reactor pressure vessel (RPV) and the conditions leading to arrest of a propagating crack. Objectives of these studies are to determine (1) if the material will exhibit crack-arrest behavior when the driving force on a crack exceeds the ASME limit, (2) the relationship between K Ia and temperature, and (3) the interaction of fracture modes (arrest, stable crack growth, unstable crack growth, and tensile instability) when arrest occurs at high temperatures. In meeting these objectives, crack-arrest data are being developed over an expanded temperature range through tests involving large thermally shocked cylinders, pressurized thermally shocked vessels, and wide-plate specimens. The wide-plate specimens provide the opportunity for a significant number of data points to be obtained at relatively affordable costs. These tests are designed to provide fracture-toughness measurements approaching or above the onset of the Charpy upper-shelf regime in a rising toughness region and with an increasing driving force. This document discusses test methodology and results. 23 refs., 92 figs., 25 tabs

Rock fill in a KBS-3 repository. Rock material for filling of shafts and ramps in a KBS-3V repository in the closure phase

International Nuclear Information System (INIS)

Pusch, Roland

2008-09-01

The content of large blocks in blasted rock makes it impossible to fill and compact the material effectively unless those larger than about 500 mm are removed. Tunnel Boring Machine (TBM) muck gives flat chips, that are usually not longer than a couple of decimeters, and serves better as backfill. The granulometrical composition of both types can be more suitable for effective compaction by crushing, which is hence a preferable process. Use of unsorted, unprocessed blasted rock can only be accepted if the density and physical properties, like self-compaction, are not important. Crushing of blasted rock and TBM muck for backfilling can be made in one or two steps depending on the required gradation. Placement of rock fill is best made by use of tractors with blades that push the material forwards over already placed and compacted material. The dry density of well graded rock fill effectively compacted by very heavy vibratory rollers can be as high as 2,400 kg/m3. For road compaction by ordinary vibratory rollers common dry density values are in the interval 2,050 to 2,200 kg m 3 . Blasted rock dumped and moved on site by tractors can get an average dry density of 1,600-1,800 kg/m3 without compaction. Crushed, blasted rock and TBM muck placed by tractors in horizontal layers and compacted by 5-10 t vibrating rollers in the lower part of the rooms, and moved by tractors to form inclined layers compacted by vibrating plates in the upper part, would get a dry density of 1,900-2,000 kg/m 3 . Flushing water over the rock fill in conjunction with the compaction work gives more effective densification than dry compaction. Based on recorded settlement of Norwegian rock fill dams constructed with water flushing it is estimated that the self-compaction of a 5 m high backfill of crushed rock or TBM muck causes a settlement of the top of the backfill of about 8 mm while a 200 m high shaft fill would undergo compression by more than half a meter. Repeated, strong earthquakes may

Rock fill in a KBS-3 repository. Rock material for filling of shafts and ramps in a KBS-3V repository in the closure phase

Energy Technology Data Exchange (ETDEWEB)

Pusch, Roland (Geodevelopment International AB/SWECO AB, Lund (Sweden))

2008-09-15

The content of large blocks in blasted rock makes it impossible to fill and compact the material effectively unless those larger than about 500 mm are removed. Tunnel Boring Machine (TBM) muck gives flat chips, that are usually not longer than a couple of decimeters, and serves better as backfill. The granulometrical composition of both types can be more suitable for effective compaction by crushing, which is hence a preferable process. Use of unsorted, unprocessed blasted rock can only be accepted if the density and physical properties, like self-compaction, are not important. Crushing of blasted rock and TBM muck for backfilling can be made in one or two steps depending on the required gradation. Placement of rock fill is best made by use of tractors with blades that push the material forwards over already placed and compacted material. The dry density of well graded rock fill effectively compacted by very heavy vibratory rollers can be as high as 2,400 kg/m3. For road compaction by ordinary vibratory rollers common dry density values are in the interval 2,050 to 2,200 kg m3. Blasted rock dumped and moved on site by tractors can get an average dry density of 1,600-1,800 kg/m3 without compaction. Crushed, blasted rock and TBM muck placed by tractors in horizontal layers and compacted by 5-10 t vibrating rollers in the lower part of the rooms, and moved by tractors to form inclined layers compacted by vibrating plates in the upper part, would get a dry density of 1,900-2,000 kg/m3. Flushing water over the rock fill in conjunction with the compaction work gives more effective densification than dry compaction. Based on recorded settlement of Norwegian rock fill dams constructed with water flushing it is estimated that the self-compaction of a 5 m high backfill of crushed rock or TBM muck causes a settlement of the top of the backfill of about 8 mm while a 200 m high shaft fill would undergo compression by more than half a meter. Repeated, strong earthquakes may

High cesium concentrations in groundwater in the upper 1.2 km of fractured crystalline rock - Influence of groundwater origin and secondary minerals

Science.gov (United States)

Mathurin, Frédéric A.; Drake, Henrik; Tullborg, Eva-Lena; Berger, Tobias; Peltola, Pasi; Kalinowski, Birgitta E.; Åström, Mats E.

2014-05-01

Dissolved and solid phase cesium (Cs) was studied in the upper 1.2 km of a coastal granitoid fracture network on the Baltic Shield (Äspö Hard Rock Laboratory and Laxemar area, SE Sweden). There unusually high Cs concentrations (up to 5-6 μg L-1) occur in the low-temperature (single and primary control of dissolved Cs in these systems. The high Cs concentrations in the saline groundwater is ascribed to long-term weathering of minerals, primarily Cs-enriched fracture coatings dominated by illite and mixed-layer clays and possibly wall rock micaceous minerals. The high Cs concentrations in the groundwater of marine origin are, in contrast, explained by relatively fast cation exchange reactions. As indicated by the field data and predicted by 1D solute transport modeling, alkali cations with low-energy hydration carried by intruding marine water are capable of (NH4+ in particular and K+ to some extent) replacing Cs+ on frayed edge (FES) sites on illite in the fracture coatings. The result is a rapid and persistent (at least in the order of decades) buildup of dissolved Cs concentrations in fractures where marine water flows downward. The identification of high Cs concentrations in young groundwater of marine origin and the predicted capacity of NH4+ to displace Cs from fracture solids are of particular relevance in the disposal of radioactive nuclear waste deep underground in crystalline rock.

Refutation of stylistic constructs in palaeolithic rock art

International Nuclear Information System (INIS)

Bednarik, R.G.

1995-01-01

This paper describes the first experiment of applying a series of dating methods at a single rock art site in a ''blind test''. The rock art in question, in northeastern Portugal, had been unanimously attributed to the Upper Palaeolithic by stylistic comparison. Four independent assessments have produced the identical result that the rock art is in fact of the second half of the Holocene, and mostly under 3,000 years old. This finding is compared with other recent dating results which together show that stylistic dating is not an admissible method of determining the age of Palaeolithic art. (author). 17 refs., 1 fig., 1 photo

The Importance of Lower Mantle Structure to Plate Stresses and Plate Motions

Science.gov (United States)

Holt, W. E.; Wang, X.; Ghosh, A.

2016-12-01

Plate motions and plate stresses are widely assumed as the surface expression of mantle convection. The generation of plate tectonics from mantle convection has been studied for many years. Lithospheric thickening (or ridge push) and slab pull forces are commonly accepted as the major driving forces for the plate motions. However, the importance of the lower mantle to plate stresses and plate motions remains less clear. Here, we use the joint modeling of lithosphere and mantle dynamics approach of Wang et al. (2015) to compute the tractions originating from deeper mantle convection and follow the method of Ghosh et al. (2013) to calculate gravitational potential energy per unit area (GPE) based on Crust 1.0 (Laske et al., 2013). Absolute values of deviatoric stresses are determined by the body force distributions (GPE gradients and traction magnitudes applied at the base of the lithosphere). We use the same relative viscosity model that Ghosh et al. (2013) used, and we solve for one single adjustable scaling factor that multiplies the entire relative viscosity field to provide absolute values of viscosity throughout the lithosphere. This distribution of absolute values of lithosphere viscosities defines the magnitudes of surface motions. In this procedure, the dynamic model first satisfies the internal constraint of no-net-rotation of motions. The model viscosity field is then scaled by the single factor until we achieve a root mean square (RMS) minimum between computed surface motions and the kinematic no-net-rotation (NNR) model of Kreemer et al. (2006). We compute plate stresses and plate motions from recently published global tomography models (over 70 based on Wang et al., 2015). We find that RMS misfits are significantly reduced when details of lower mantle structure from the latest tomography models are added to models that contain only upper and mid-mantle density distributions. One of the key reasons is that active upwelling from the Large Low Shear

Geochemical tracing and hydrogeochemical modelling of water-rock interactions during salinization of alluvial groundwater (Upper Rhine Valley, France)

Energy Technology Data Exchange (ETDEWEB)

Lucas, Y., E-mail: yann.lucas@eost.u-strasbg.fr [Universite de Strasbourg et CNRS, Laboratoire d' Hydrologie et de Geochimie de Strasbourg, Ecole et Observatoire des Sciences de la Terre, 1, rue Blessig, 67084 Strasbourg Cedex (France); Schmitt, A.D., E-mail: anne-desiree.schmitt@univ-fcomte.fr [Universite de Strasbourg et CNRS, Laboratoire d' Hydrologie et de Geochimie de Strasbourg, Ecole et Observatoire des Sciences de la Terre, 1, rue Blessig, 67084 Strasbourg Cedex (France)] [Universite de Franche-Comte et CNRS-UMR 6249, Chrono-Environnement, 16, Route de Gray, 25030 Besancon Cedex (France); Chabaux, F., E-mail: francois.chabaux@eost.u-strasbg.fr [Universite de Strasbourg et CNRS, Laboratoire d' Hydrologie et de Geochimie de Strasbourg, Ecole et Observatoire des Sciences de la Terre, 1, rue Blessig, 67084 Strasbourg Cedex (France); Clement, A.; Fritz, B. [Universite de Strasbourg et CNRS, Laboratoire d' Hydrologie et de Geochimie de Strasbourg, Ecole et Observatoire des Sciences de la Terre, 1, rue Blessig, 67084 Strasbourg Cedex (France); Elsass, Ph. [BRGM, GEODERIS, 1, rue Claude Chappe, 57070 Metz (France); Durand, S. [Universite de Strasbourg et CNRS, Laboratoire d' Hydrologie et de Geochimie de Strasbourg, Ecole et Observatoire des Sciences de la Terre, 1, rue Blessig, 67084 Strasbourg Cedex (France)

2010-11-15

Research highlights: {yields} Major and trace elements along with strontium and uranium isotopic ratios show that groundwater geochemical characteristics along the saline plumes cannot reflect a conservative mixing. {yields} A coupled hydrogeochemical model demonstrates that cationic exchange between alkalis from polluted waters and alkaline-earth elements from montmorillonite present in the host rock of the aquifer is the primary process. {yields} The model requires only a small amount of montmorillonite. {yields} It is necessary to consider the pollution history to explain the important chloride, sodium and calcium concentration modifications. {yields} The model shows that the rapidity of the cationic exchange reactions insures a reversibility of the cation fixation on clays in the aquifer. - Abstract: In the southern Upper Rhine Valley, groundwater has undergone intensive saline pollution caused by the infiltration of mining brines, a consequence of potash extraction carried out during the 20th century. Major and trace elements along with Sr and U isotopic ratios show that groundwater geochemical characteristics along the saline plumes cannot reflect conservative mixing between saline waters resulting from the dissolution of waste heaps and one or more unpolluted end-members. The results imply the occurrence of interactions between host rocks and polluted waters, and they suggest that cationic exchange mechanisms are the primary controlling process. A coupled hydrogeochemical model has been developed with the numerical code KIRMAT, which demonstrates that cationic exchange between alkalis from polluted waters and alkaline-earth elements from montmorillonite present in the host rock of the aquifer is the primary process controlling the geochemical evolution of the groundwater. The model requires only a small amount of montmorillonite (between 0.75% and 2.25%), which is in agreement with the observed mineralogical composition of the aquifer. The model also proves

Underground laboratories for rock mechanics before radioactive waste

International Nuclear Information System (INIS)

Duffaut, P.

1985-01-01

Many rock mechanics tests are performed in situ, most of them underground since 1936 at the Beni Bahdel dam. The chief tests for understanding the rock mass behaviour are deformability tests (plate test and pressure cavern test, including creep experiments) and strength tests (compression of a mine pillar, shear test on rock mass or joint). Influence of moisture, heat, cold and freeze are other fields of investigation which deserve underground laboratories. Behaviour of test galleries, either unsupported or with various kinds of support, often is studied along time, and along the work progression, tunnel face advance, enlargement or deepening of the cross section. The examples given here help to clarify the concept of underground laboratory in spite of its many different objectives. 38 refs.; 1 figure; 1 table

Importance of the Decompensative Correction of the Gravity Field for Study of the Upper Crust: Application to the Arabian Plate and Surroundings

Science.gov (United States)

Kaban, Mikhail K.; El Khrepy, Sami; Al-Arifi, Nassir

2017-01-01

The isostatic correction represents one of the most useful "geological" reduction methods of the gravity field. With this correction it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. However, even this reduction does not show the full gravity effect of unknown anomalies in the upper crust since their impact is substantially reduced by the isostatic compensation. We analyze a so-called decompensative correction of the isostatic anomalies, which provides a possibility to separate these effects. It was demonstrated that this correction is very significant at the mid-range wavelengths and may exceed 100 m/s2 (mGal), therefore ignoring this effect would lead to wrong conclusions about the upper crust structure. At the same time, the decompensative correction is very sensitive to the compensation depth and effective elastic thickness of the lithosphere. Therefore, these parameters should be properly determined based on other studies. Based on this technique, we estimate the decompensative correction for the Arabian plate and surrounding regions. The amplitude of the decompensative anomalies reaches ±250 m/s2 10-5 (mGal), evidencing for both, large density anomalies of the upper crust (including sediments) and strong isostatic disturbances of the lithosphere. These results improve the knowledge about the crustal structure in the Middle East.

Fuel cell plates with skewed process channels for uniform distribution of stack compression load

Science.gov (United States)

Granata, Jr., Samuel J.; Woodle, Boyd M.

1989-01-01

An electrochemical fuel cell includes an anode electrode, a cathode electrode, an electrolyte matrix sandwiched between electrodes, and a pair of plates above and below the electrodes. The plate above the electrodes has a lower surface with a first group of process gas flow channels formed thereon and the plate below the electrodes has an upper surface with a second group of process gas flow channels formed thereon. The channels of each group extend generally parallel to one another. The improvement comprises the process gas flow channels on the lower surface of the plate above the anode electrode and the process gas flow channels on the upper surface of the plate below the cathode electrode being skewed in opposite directions such that contact areas of the surfaces of the plates through the electrodes are formed in crisscross arrangements. Also, the plates have at least one groove in areas of the surfaces thereof where the channels are absent for holding process gas and increasing electrochemical activity of the fuel cell. The groove in each plate surface intersects with the process channels therein. Also, the opposite surfaces of a bipolar plate for a fuel cell contain first and second arrangements of process gas flow channels in the respective surfaces which are skewed the same amount in opposite directions relative to the longitudinal centerline of the plate.

The northern Lesser Antilles oblique subduction zone: new insight about the upper plate deformation, 3D slab geometry and interplate coupling.

Science.gov (United States)

Marcaillou, B.; Laurencin, M.; Graindorge, D.; Klingelhoefer, F.

2017-12-01

In subduction zones, the 3D geometry of the plate interface is thought to be a key parameter for the control of margin tectonic deformation, interplate coupling and seismogenic behavior. In the northern Caribbean subduction, precisely between the Virgin Islands and northern Lesser Antilles, these subjects remain controversial or unresolved. During the ANTITHESIS cruises (2013-2016), we recorded wide-angle seismic, multichannel reflection seismic and bathymetric data along this zone in order to constrain the nature and the geometry of the subducting and upper plate. This experiment results in the following conclusions: 1) The Anegada Passage is a 450-km long structure accross the forearc related to the extension due to the collision with the Bahamas platform. 2) More recently, the tectonic partitioning due to the plate convergence obliquity re-activated the Anegada Passage in the left-lateral strike-slip system. The partitioning also generated the left-lateral strike-slip Bunce Fault, separating the accretionary prism from the forearc. 3) Offshore of the Virgin Islands margin, the subducting plate shows normal faults parallel to the ancient spreading center that correspond to the primary fabric of the oceanic crust. In contrast, offshore of Barbuda Island, the oceanic crust fabric is unresolved (fracture zone?, exhumed mantle? ). 4) In the direction of the plate convergence vector, the slab deepening angle decreases northward. It results in a shallower slab beneath the Virgin Islands Platform compared to the St Martin-Barbuda forearc. In the past, the collision of the Bahamas platform likely changed the geodynamic settings of the northeastern corner of the Caribbean subduction zone and we present a revised geodynamic history of the region. Currently, various features are likely to control the 3D geometry of the slab: the margin convexity, the convergence obliquity, the heterogeneity of the primary fabric of the oceanic crust and the Bahamas docking. We suggest that

Extended plate and beam demonstration home

Science.gov (United States)

Patricia Gunderson; Vladimir Kochkin; Xiping Wang

2018-01-01

An extended plate and beam (EP&B) design was developed at Home Innovation Research Labs (Upper Marlboro, Maryland) in an effort to provide traditional light-frame wall construction details that are compatible with continuous insulating sheathing. This would encourage wide-spread adoption of high-R walls and promote greater energy efficiency in new houses. The...

Effect of Interaction and Rocking Motion on The Earthquake Response of Buildings

Directory of Open Access Journals (Sweden)

Gholamreza Havaei

2015-03-01

Full Text Available Usually structures are designed under codes based on the assumption that the soil stiffness is infinite, so the foundation rests firmly on the soil. In many cases, the overturning moment due to the lateral forces may exceed the resisting moment due to the gravity forces. Thus, this may cause a foundation uplift because in reality the soil stiffness is not infinite and the structure stands up under gravity forces. The phenomenon of foundation uplifting and its impact on the soil are known as the rocking motion.This study investigates the influence of the rocking motion and interaction by the yielding base plates on the nonlinear behavior of steel structures under dynamic analysis. More specifically, Three- five and seven -storied structuresare designed with ordinary ductility, then the structuresare analyzed in rigid and deformable base plate cases with using the ABAQUS software.The results show that the rocking motion and Interaction decrease the response of buildings such as the base shear, the axial force of columns and the strain energy but also increase the natural period.

Jacking mechanism for upper internals structure of a liquid metal nuclear reactor

International Nuclear Information System (INIS)

Gillett, J.E.; Wineman, A.L.

1983-01-01

A jacking mechanism for raising the upper internals structure of a liquid metal nuclear reactor which jacking mechanism uses a system of gears and drive shafts to transmit force from a single motor to four mechanically synchronized ball jacks to raise and lower support columns which support the upper internals structure. The support columns each have a pin which rides in a slot in a housing fixed to the reactor head. The pin has two locking plates which can be rotated around the pin to bring the locking plates into engagement with the housing in a raised or a lowered position of the support column such that the support column is then supported by the locking plate and not by the ball screw jacks. (author)

Indonesian Landforms and Plate Tectonics

Directory of Open Access Journals (Sweden)

Herman Th. Verstappen

2014-06-01

Full Text Available DOI: 10.17014/ijog.v5i3.103The horizontal configuration and vertical dimension of the landforms occurring in the tectonically unstable parts of Indonesia were resulted in the first place from plate tectonics. Most of them date from the Quaternary and endogenous forces are ongoing. Three major plates – the northward moving Indo-Australian Plate, the south-eastward moving SE-Asian Plate and the westward moving Pacific Plate - meet at a plate triple-junction situated in the south of New Guinea’s Bird’s Head. The narrow North-Moluccan plate is interposed between the Asia and Pacific. It tapers out northward in the Philippine Mobile Belt and is gradually disappearing. The greatest relief amplitudes occur near the plate boundaries: deep ocean trenches are associated with subduction zones and mountain ranges with collision belts. The landforms of the more stable areas of the plates date back to a more remote past and, where emerged, have a more subdued relief that is in the first place related to the resistance of the rocks to humid tropical weathering Rising mountain ranges and emerging island arcs are subjected to rapid humid-tropical river erosions and mass movements. The erosion products accumulate in adjacent sedimentary basins where their increasing weight causes subsidence by gravity and isostatic compensations. Living and raised coral reefs, volcanoes, and fault scarps are important geomorphic indicators of active plate tectonics. Compartmental faults may strongly affect island arcs stretching perpendicular to the plate movement. This is the case on Java. Transcurrent faults and related pull-apart basins are a leading factor where plates meet at an angle, such as on Sumatra. The most complicated situation exists near the triple-junction and in the Moluccas. Modern research methods, such as GPS measurements of plate movements and absolute dating of volcanic outbursts and raised coral reefs are important tools. The mega-landforms resulting

Harttia absaberi, a new species of loricariid catfish (Siluriformes: Loricariidae: Loricariinae from the upper rio Paraná basin, Brazil

Directory of Open Access Journals (Sweden)

Osvaldo Takeshi Oyakawa

Full Text Available A new species of Harttia, tribe Harttiini, is described from tributaries of upper portions of rio Paraná drainage. The new species, the smallest known species of the genus, attaining up to 74.0 mm of standard length, can be distinguished from its congeners by the combination of the following characters: abdomen completely covered by plates, a single preanal plate, plates of the gular area in broad contact with the canal plate. Harttia absaberi is the second species of the genus known from the upper portion of rio Paraná drainage.

Plasticity, Fracture and Friction in Steady-State Plate Cutting

DEFF Research Database (Denmark)

Simonsen, Bo Cerup; Wierzbicki, Tomasz

1997-01-01

perpendicular to the direction of motion is derived theoretically in a consistent manner. The perpendicular reaction force is of paramount importance for prediction the structural damage of a ship hull because it governs the vertical ship motion and rock penetration which is strongly coupled with the horizontal...... extension of the presented plate model to include more structural members as for example the stiffeners attached to a ship bottom plating. The fracture process is discussed and the model is formulated partly on the basis of the material fracture toughness. The effect of friction and the reaction force...

The organic matter of the Potosi basin (Cordillera Oriental, Bolivia) during the Upper Cretaceous-Lower tertiary: stratigraphic and palaeogeographic data

Energy Technology Data Exchange (ETDEWEB)

Blanc-Valleron, M.M.; Rouchy, J.M. (Centre National de la Recherche Scientifique (CNRS), 75 - Paris (France)); Schuler, M.; Rauscher, R. (Strasbourg-1 Univ., 67 (France)); Camoin, G. (Aix-Marseille-1 Univ., 13 - Marseille (France))

1994-12-01

Palynological and Rock-Eval pyrolysis studies of the Chaunaca and El Molino Fm (Santonian to Thanetian, Cordillera Oriental, Bolivia) indicate that some facies have economic significance as potential oil source rocks. The occurrence of Pediastrum and Azolla testify a lacustrine environment. In the Upper Molino, the environmental interpretation of an almost monospecific association of dinocysts is discussed. The presence of Apectodinium quinquelatum indicates that the age of the upper part of the Upper El Molino Fm is likely to be Upper Thanetian. (authors). 22 refs., 5 figs.

Experiments of dike-induced deformation: Insights on the long-term evolution of divergent plate boundaries

KAUST Repository

Trippanera, D.

2015-10-22

The shallow transport of magma occurs through dikes causing surface deformation. Our understanding of the effects of diking at the surface is limited, especially on the long term, for repeated intrusive episodes. We use analogue models to study the upper crustal deformation induced by dikes. We insert metal plates within cohesive sand with three setups: in setup A, the intrusion rises upward with constant thickness and in setups B and C, the intrusion thickens at a fixed depth, with final rectangular (setup B) or triangular (setup C) shape in section. Setup A creates a doming delimited by reverse faults, with secondary apical graben, without close correspondence in nature. In setups B and C, a depression flanked by two uplifted areas is bordered by inward dipping normal faults propagating downward and, for deeper intrusions in setup B, also by inner faults, reverse at the surface; this deformation is similar to what is observed in nature, suggesting a consistent physical behavior. Dikes in nature initially propagate developing a mode I fracture at the tip, subsequently thickened by magma intrusion, without any host rock translation in the propagation direction (as in setup A). The deformation pattern in setups B and C depends on the intrusion depth and thickness, consistently to what is observed along divergent plate boundaries. The early deformation in setups B and C is similar to that from a single rifting episode (i.e., Lakagigar, Iceland, and Dabbahu, Afar), whereas the late stages resemble the structure of mature rifts (i.e., Krafla, Iceland), confirming diking as a major process in shaping divergent plate boundaries.

Eddy current heating of irregularly shaped plates by slow ramped fields

International Nuclear Information System (INIS)

Dresner, L.

1979-01-01

Theorems are presented for estimating eddy current heating of irregularly shaped plates by a perpendicular ramped field. The theorems, which are derived from two complementary variational principles, give upper and lower bounds to the eddy current heating. Illustrative results are given for rectangles, isosceles triangles, sectors of circular annuli, rhombuses, and L-shaped plates. A comparison is made with earlier work

A Plastic Flow and Rheomorfic Differentiation of the Mantle Ultramafic Rocks

Directory of Open Access Journals (Sweden)

D. E. Saveliev

2014-12-01

Full Text Available In this paper, the general characteristics of morphological features of the ophiolitic ultramafic rock formations are discussed. The ultramafic rocks are the fragments of upper mantle, which were exposed on the surface due to tectonic events. It is shown that their main chemical and structural characteristic is a stratification accompanied by separation of the rheologically weakest dunite bodies usually containing the economic amount of chromite ore. Based on results of conducted analysis, we propose a new hypothesis of petro- and ore genesis in the upper mantle. Using the thermodynamic approach, we developed the rheomorfic model of the differentiation of the mantle matter. This model solves many problems inherent to currently used magmatic or metasomatic models.

Manipulation of the response of human endothelial colony-forming cells by focal adhesion assembly using gradient nanopattern plates.

Science.gov (United States)

Cui, Long-Hui; Joo, Hyung Joon; Kim, Dae Hwan; Seo, Ha-Rim; Kim, Jung Suk; Choi, Seung-Cheol; Huang, Li-Hua; Na, Ji Eun; Lim, I-Rang; Kim, Jong-Ho; Rhyu, Im Joo; Hong, Soon Jun; Lee, Kyu Back; Lim, Do-Sun

2018-01-01

Nanotopography plays a pivotal role in the regulation of cellular responses. Nonetheless, little is known about how the gradient size of nanostructural stimuli alters the responses of endothelial progenitor cells without chemical factors. Herein, the fabrication of gradient nanopattern plates intended to mimic microenvironment nanotopography is described. The gradient nanopattern plates consist of nanopillars of increasing diameter ranges [120-200 nm (GP 120/200), 200-280 nm (GP 200/280), and 280-360 nm (GP 280/360)] that were used to screen the responses of human endothelial colony-forming cells (hECFCs). Nanopillars with a smaller nanopillar diameter caused the cell area and perimeter of hECFCs to decrease and their filopodial outgrowth to increase. The structure of vinculin (a focal adhesion marker in hECFCs) was also modulated by nanostructural stimuli of the gradient nanopattern plates. Moreover, Rho-associated protein kinase (ROCK) gene expression was significantly higher in hECFCs cultured on GP 120/200 than in those on flat plates (no nanopillars), and ROCK suppression impaired the nanostructural-stimuli-induced vinculin assembly. These results suggest that the gradient nanopattern plates generate size-specific nanostructural stimuli suitable for manipulation of the response of hECFCs, in a process dependent on ROCK signaling. This is the first evidence of size-specific nanostructure-sensing behavior of hECFCs. Nano feature surfaces are of growing interest as materials for a controlled response of various cells. In this study, we successfully fabricated gradient nanopattern plates to manipulate the response of blood-derived hECFCs without any chemical stimulation. Interestingly, we find that the sensitive nanopillar size for manipulation of hECFCs is range between 120 nm and 200 nm, which decreased the area and increased the filopodial outgrowth of hECFCs. Furthermore, we only modulate the nanopillar size to increase ROCK expression can be an

Lithology, microstructures, fluid inclusions, and geochemistry of rock salt and of the cap-rock contact in Oakwood Dome, East Texas: significance for nuclear waste storage. Report of investigations No. 120

International Nuclear Information System (INIS)

Dix, O.R.; Jackson, M.P.A.

1982-01-01

Oakwood salt dome in Leon and Freestone Counties, Texas, has a core composed of a diapiric salt stock at a depth of 355 m. A vertical borehole in the center of the salt stock yielded 57.3 m of continuous rock-salt core overlain by 137 m of anhydrite-calcite cap rock. The lower 55.3 m of rock salt exhibits a strong, penetrative schistosity and parallel cleavage dipping at 30 to 40 0 and more than 60 variably dipping layers of disseminated anhydrite. Anhydrite constitutes 1.3 +- 0.7 percent of the rock-salt core. The upper 2 m of rock salt is unfoliated, comprising a lower 1.4-m interval of medium-grained granoblastic rock salt and an upper 0.6-m interval of coarse-grained granoblastic rock salt. An abrupt, cavity-free contact separates rock salt from laminated cap rock consisting of granoblastic-polygonal anhydrite virtually devoid of halite or pore space. Microstructures and concentration gradients of fluid inclusions suggest that the unfoliated rock salt at the crest of the salt stock was once strongly foliated, but that this fabric was destroyed by solid-state recrystallization. Downward movement of brine from the rock-salt - cap-rock contact was apparently accompanied by two recrystallization fronts. Dissolution of halite at the contact released disseminated anhydrite that presumably accumulated as sand on the floor of the dissolution cavity. Renewed rise of the salt stock closed the cavity, and the anhydrite sand was accreted against the base of the cap rock. Much, if not all, of the lamination in the 80 m of anhydrite cap rock may result from cycles of dissolution, recrystallization, and upward movement in the salt stock, followed by accretion of anhydrite residuum as laminae against the base of the cap rock. These processes, which are strongly influenced by fluids, act both to breach waste repositories and to geologically isolate them

Heating effects in Rio Blanco rock

International Nuclear Information System (INIS)

Taylor, R.W.; Bowen, D.W.; Rossler, P.E.

1975-01-01

Samples of ''sandstone'' from near the site of the upper Rio Blanco nuclear explosion were heated in the laboratory at temperatures between 600 and 900 0 C. The composition and amount of noncondensable (dry) gas released were measured and compared to the amount and composition of gas found underground following the explosion. The gas released from the rock heated in the laboratory contained approximately 80 percent CO 2 and 10 percent H 2 ; the balance was CO and CH 4 . With increasing temperature, the amounts of CO 2 , CO, and H 2 released increased. The composition of gas released by heating Rio Blanco rock in the laboratory is similar to the composition of gas found after the nuclear explosion except that it contains less natural gas (CH 4 , C 2 H 6 . . .). The amount of noncondensable gas released by heating the rock increases from approximately 0.1 mole/kg of rock at 600 0 C to 0.9 mole/kg at 900 0 C. Over 90 percent of the volatile components of the rock are released in less than 10 h at 900 0 C. A comparison of the amount of gas released by heating rock in the laboratory to the amount of gas released by the heat of the Rio Blanco nuclear explosion suggests that the explosion released the volatile material from about 0.42 mg of rock per joule of explosive energy (1700 to 1800 tonnes per kt). (auth)

Petrophysical Characteristics of Rocks in Girei Local Government ...

African Journals Online (AJOL)

Petrophysical measurements namely; electrical resistivity, density, porosity, electrical resistivity anisotropy and water saturation were performed on fourteen representative surface rock samples from Girei, part of the Yola arm of the Upper Benue trough, NE Nigeria. The purpose was to provide information required for ...

Spirit's View Beside 'Home Plate' on Sol 1823

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this 180-degree view of the rover's surroundings during the 1,823rd Martian day, or sol, of Spirit's surface mission (Feb. 17, 2009). The center of the view is toward the south-southwest. The rover had driven 7 meters (23 feet) eastward earlier on Sol 1823, part of maneuvering to get Spirit into a favorable position for climbing onto the low plateau called 'Home Plate.' However, after two driving attempts with negligible progress during the following three sols, the rover team changed its strategy for getting to destinations south of Home Plate. The team decided to drive Spirit at least partway around Home Plate, instead of ascending the northern edge and taking a shorter route across the top of the plateau. Layered rocks forming part of the northern edge of Home Plate can be seen near the center of the image. Rover wheel tracks are visible at the lower edge. This view is presented as a cylindrical projection with geometric seam correction.

Physiologically Relevant Prosthetic Limb Movement Feedback for Upper and Lower Extremity Amputees

Science.gov (United States)

2016-10-01

upper arm (elbow movement), Upper leg (knee movement) and lower leg ( ankle movement) to provide a physiologically relevant sense of limb movement...Additionally a BOA cable tensioning system is passed through these plates and anchored to the external surface of the socket. When tension is applied the

Isostatic models and isostatic gravity anomalies of the Arabian plate and surroundings

Science.gov (United States)

Kaban, Mikhail K.; El Khrepy, Sami; Al-Arifi, Nassir

2015-04-01

Isostaic anomalies represent one of the most useful "geological" reduction of the gravity field. With the isostatic correction it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. This correction is based on the fact that a major part of the near-surface load is compensated by variations of the lithosphere boundaries (chiefly the Moho and LAB) and by density variations within the crust and upper mantle. It is usually supposed that it is less important to a first order, what is the actual compensation model when reducing the effect of compensating masses, since their total weight is exactly opposite to the near-surface load. We compare several compensating models for the Arabian plate and surrounding area. The Airy model gives very significant regional isostatic anomalies, which can not be explained by the upper crust structure or disturbances of the isostatic equilibrium. Also the predicted "isostatic" Moho is very different from the existing observations. The second group of the isostatic models includes the Moho, which is based on existing seismic determinations. Additional compensation is provided by density variations within the lithosphere (chiefly in the upper mantle). In this way we minimize regional anomalies over the Arabian plate. The residual local anomalies well correspond to tectonic structure of the plate. Still very significant anomalies are associated with the Zagros fold belt, the collision zone of the Arabian and Eurasian plates.

Analysis of Plasticity, Fracture and Friction in Steady State Plate Cutting

DEFF Research Database (Denmark)

Simonsen, Bo Cerup; Wierzbicki, Tomasz

1996-01-01

perpendicular to the direction of motion is derived theoretically in a new consistent manner. The perpendicular reaction force is of paramount importance for predicting the structural damage of a ship hull because it governs the vertical ship motion and rock penetration which is strongly coupled...... extension of the presented plate model to include more structural members as for example the stiffeners attached to a ship bottom plating. The fracture process is discussed and the model is formulated partly on the basis of the material fracture toughness. The effect of friction and the reaction force...

Rock Cycle Sagas: The STRATegy COLUMN for Precollege Science Teachers.

Science.gov (United States)

Metzger, Ellen Pletcher

1994-01-01

Reviews The Best of BAESI: Earth Science Activities & Recommended Resources from the Bay Area Earth Science Institute. The Best of BAESI is divided into two parts. Part I contains 19 classroom activities on topographic maps, rocks and minerals, earthquakes, volcanoes, and plate tectonics. Part II describes resources and identifies government…

Water infiltration into exposed fractured rock surfaces

International Nuclear Information System (INIS)

Rasmussen, T.C.; Evans, D.D.

1993-01-01

Fractured rock media are present at many existing and potential waste disposal sites, yet characterization data and physical relationships are not well developed for such media. This study focused on water infiltration characteristics of an exposed fractured rock as an approach for defining the upper boundary condition for unsaturated-zone water percolation and contaminant transport modeling. Two adjacent watersheds of 0.24 and 1.73 ha with slopes up to 45% were instrumented for measuring rainfall and runoff. Fracture density was measured from readily observable fracture traces on the surface. Three methods were employed to evaluate the rainfall-runoff relationship. The first method used the annual totals and indicated that only 22.5% of rainfall occurred as runoff for the 1990-1991 water year, which demonstrates a high water intake rate by the exposed fracture system. The second method employed total rainfall and runoff for individual storms in conjunction with the commonly used USDA Soil Conservation Service curve number method developed for wide ranges of soils and vegetation. Curve numbers between 75 and 85 were observed for summer and winter storms with dry antecedent runoff conditions, while values exceeded 90 for wet conditions. The third method used a mass-balance approach for four major storms, which indicated that water intake rates ranged from 2.0 to 7.3 mm h -1 , yielding fracture intake velocities ranging from 122 to 293 m h -1 . The three analyses show the complexity of the infiltration process for fractured rock. However, they contribute to a better understanding of the upper boundary condition for predicting contaminant transport through an unsaturated fractured rock medium. 17 refs., 4 figs., 1 tab

Energetic solutions of Rock Sandpipers to harsh winter conditions rely on prey quality

Science.gov (United States)

Ruthrauff, Daniel R.; Dekinga, Anne; Gill, Robert E.; Piersma, Theunis

2018-01-01

Rock Sandpipers Calidris ptilocnemis have the most northerly non-breeding distribution of any shorebird in the Pacific Basin (upper Cook Inlet, Alaska; 61°N, 151°W). In terms of freezing temperatures, persistent winds and pervasive ice, this site is the harshest used by shorebirds during winter. We integrated physiological, metabolic, behavioural and environmental aspects of the non-breeding ecology of Rock Sandpipers at the northern extent of their range to determine the relative importance of these factors in facilitating their unique non-breeding ecology. Not surprisingly, estimated daily energetic demands were greatest during January, the coldest period of winter. These estimates were greatest for foraging birds, and exceeded basal metabolic rates by a factor of 6.5, a scope of increase that approaches the maximum sustained rate of energetic output by shorebirds during periods of migration, but far exceeds these periods in duration. We assessed the quality of their primary prey, the bivalve Macoma balthica, to determine the daily foraging duration required by Rock Sandpipers to satisfy such energetic demands. Based on size-specific estimates of M. balthica quality, Rock Sandpipers require over 13 h/day of foraging time in upper Cook Inlet in January, even when feeding on the highest quality prey. This range approaches the average daily duration of mudflat availability in this region (c. 18 h), a maximum value that annually decreases due to the accumulation of shore-fast ice. Rock Sandpipers are likely to maximize access to foraging sites by following the exposure of ice-free mudflats across the upper Cook Inlet region and by selecting smaller, higher quality M. balthica to minimize foraging times. Ultimately, this unusual non-breeding ecology relies on the high quality of their prey resources. Compared with other sites across their range, M. balthica from upper Cook Inlet have relatively light shells, potentially the result of the region

Development of hold down plate of INGLE fuel assembly

International Nuclear Information System (INIS)

Kim, Hyeong Koo; Kim, Kyu Tae

1996-07-01

Hold down plate for the INGLE fuel which has been designed for high performance in the standpoints of thermal margin and structural integrity compared to current fuel for YGN 3/4 and UCN 3/4 has been developed and its structural integrity has been verified based on the eh stress analysis. The design feature of the developed hold down plate has not only perfect compatibility with the reactor internals of Korea standard reactor, but also brand-new locking mechanism between upper tie plate and guide tubes. This locking mechanism introduced to the INGLE fuel provides very simple and reliable reconstitutability. In this report, finite element stress analysis with the aid of the ANSYS code as a solver and the MSC/PATRAN code as a pre and post processor were performed to verify structural integrity of the hold down plate considering various load cases which seem to be applied to the hold down plate during its lifetime. Based on the analysis results, the developed hold down plate for INGLE fuel sustains structural integrity under considered load conditions. 3 tabs., 16 figs., 9 refs. (Author)

Multiple ways of producing intermediate and silicic rocks within Thingmúli and other Icelandic volcanoes

DEFF Research Database (Denmark)

Charreteur, Gilles; Tegner, Christian; Haase, Karsten

2013-01-01

Major and trace element compositions of rocks and coexisting phenocrysts of the ThingmA(0)li volcano suggest a revision of the existing models for the formation of intermediate and silicic melts in Iceland. The new data define two compositional tholeiitic trends with a significant gap between the...... between the compositions of intermediate and silicic rocks and plate tectonic setting, therefore, should be avoided....

Remedial Action Plan and Site Design for stabilization of the inactive Uranium Mill Tailings sites at Slick Rock, Colorado: Appendix C to Attachment 3, Calculations. Final

International Nuclear Information System (INIS)

1995-09-01

This volume contains calculations for: Slick Rock processing sites background ground water quality; Slick Rock processing sites lysimeter water quality; Slick Rock processing sites on-site and downgradient ground water quality; Slick Rock disposal site background water quality; Burro Canyon disposal site, Slick Rock, Colorado, average hydraulic gradients and average liner ground water velocities in the upper, middle, and lower sandstone units of the Burro Canyon formation; Slick Rock--Burro Canyon disposal site, Burro Canyon pumping and slug tests--analyses; water balance and surface contours--Burro Canyon disposal cell; and analytical calculation of drawdown in a hypothetical well completed in the upper sandstone unit of the Burro Canyon formation

'Home Plate' Evidence for an Explosive Past

Science.gov (United States)

2006-01-01

This view of layers around the edge of a low plateau called 'Home Plate' inside Mars' Gusev Crater includes a feature that may be what geologists call a 'bomb sag' and interpret as evidence of an explosive event, such as a volcanic eruption. The layers seen here are generally straight and parallel except in the lower right, where they dip around a greyish rock that is about 4 centimeters (about 1.5 inches) in diameter. When layered deposits are struck by a falling rock while the layers are still soft, this type of pattern can be created. The rock might have been lofted by a volcanic burst or as part of the material ejected by the crater-forming impact of a meteorite. The panoramic camera (Pancam) on NASA's Mars Exploration Rover Spirit acquired the exposures for this image on Spirit's 754th Martian day (Feb. 15, 2006). This view is an approximately true-color rendering mathematically generated from separate images taken through all of the left Pancam's 432-nanometer to 753-nanometer filters.

The role of major forest fires on rock physical decay in a Mediterranean environment

Science.gov (United States)

Shtober-Zisu, Nurit; Tessler, Naama; Tsatskin, Alexander; Greenbaum, Noam

2017-04-01

Massive destruction of carbonate rocks occurred on the slopes of Mt. Carmel (Israel), during a severe forest fire in 2010. The bedrock surfaces exhibited extensive exfoliation into flakes and spalls covering up to 80%-100% of the exposed rocks; detached boulders were totally fractured or disintegrated. The fire affected six carbonate units—various types of chalk, limestone, and dolomite. The burned flakes show a consistent tendency towards flatness, in all lithologies, as 85%-95% of the flakes were detached in the form of blades, plates, and slabs. The extent of the physical disruption depends on rock composition: the most severe response was found in the chalk formations which are covered by calcrete (Nari crusts). These rocks reacted by extreme exfoliation, at an average depth of 7.7 to 9.6 cm and a maximum depth of 20 cm. Scorched and blackened faces under the upper layer of spalls provide strong evidence that chalk breakdown took place at an early stage of the fire. The extreme response of the chalks can be explained by the laminar structure of the Nari, which served as planes of weakness for the rock destruction. Three years after the fire, the rocks continue to exfoliate and break down internally. As the harder surface of the Nari was removed, the more brittle underlying chalk is exposed to erosion. These flakes seem to play an important role in reforming the soil after the fire, especially by increasing the coarse particles percentage. These, in spite of the absence of vegetation cover, improve soil infiltration and percolation rates and cause long-term changes to the hydrological regime. It is difficult to estimate the frequency of high-intensity fires in the Carmel region over the past 2-3 million years, as well as the extension and density of the vegetation. It is even harder to assess the frequency of fires (and the destruction) of a single rock outcrop. Our findings show that rock outcrop may lose even 20 cm of its thickness in a single fire. This

Crust and upper-mantle structure of Wanganui Basin and southern Hikurangi margin, North Island, New Zealand as revealed by active source seismic data

Science.gov (United States)

Tozer, B.; Stern, T. A.; Lamb, S. L.; Henrys, S. A.

2017-11-01

Wide-angle reflection and refraction data recorded during the Seismic Array HiKurangi Experiment (SAHKE) are used to constrain the crustal P-wave velocity (Vp) structure along two profiles spanning the length and width of Wanganui Basin, located landwards of the southern Hikurangi subduction margin, New Zealand. These models provide high-resolution constraints on the structure and crustal thickness of the overlying Australian and subducted Pacific plates and plate interface geometry. Wide-angle reflections are modelled to show that the subducted oceanic Pacific plate crust is anomalously thick (∼10 km) below southern North Island and is overlain by a ∼1.5-4.0 km thick, low Vp (4.8-5.4 km s-1) layer, interpreted as a channel of sedimentary material, that persists landwards at least as far as Kapiti Island. Distinct near vertical reflections from onshore shots identify a ∼4 km high mound of low-velocity sedimentary material that appears to underplate the overlying Australian plate crust and is likely to contribute to local rock uplift along the Axial ranges. The overriding Australian plate Moho beneath Wanganui Basin is imaged as deepening southwards and reaches a depth of at least 36.4 km. The Moho shape approximately mirrors the thickening of the basin sediments, suggestive of crustal downwarping. However, the observed crustal thickness variation is insufficient to explain the large negative Bouguer gravity anomaly (-160 mGal) centred over the basin. Partial serpentinization within the upper mantle with a concomitant density decrease is one possible way of reconciling this anomaly.

Measurements of upper mantle shear wave anisotropy from a permanent network in southern Mexico

NARCIS (Netherlands)

van Benthem, S.A.C.; Valenzuela, R.W.; Ponce, G.J.

2013-01-01

Upper mantle shear wave anisotropy under stations in southern Mexico was measured using records of SKS phases. Fast polarization directions where the Cocos plate subducts subhorizontally are oriented in the direction of the relative motion between the Cocos and North American plates, and are

Uranium favorability of tertiary sedimentary rocks of the western Okanogan highlands and of the upper Columbia River valley, Washington. [Measurement and sampling of surface sections, collection of samples from isolated outcrops, and chemical and mineralogical analyses of samples; no known uranium deposits

Energy Technology Data Exchange (ETDEWEB)

Marjaniemi, D.K.; Robins, J.W.

1975-08-01

Tertiary sedimentary rocks in the northern portions of the western Okanogan highlands and in the upper Columbia River valley were investigated during a regional study to determine the favorability for potential uranium resources of the Tertiary sedimentary rocks of northeastern Washington. This project involved measurement and sampling of surface sections, collection of samples from isolated outcrops, and chemical and mineralogical analyses of samples. No portion of the project area of this report is rated of high or of medium favorability for potential uranium resources. Low favorability ratings are given to Oroville, Tonasket, and Pine Creek areas of the Okanogan River valley; to the Republic graben; and to the William Lakes, Colville, and Sheep Creek areas of the upper Columbia River valley. All these areas contain some fluvial, poorly sorted feldspathic or arkosic sandstones and conglomerates. These rocks are characterized by very low permeability and a consistently high siliceous matrix suggesting very low initial permeability. There are no known uranium deposits in any of these areas, and low level uranium anomalies are rare.

Geochemical evidence for the melting of subducting oceanic lithosphere at plate edges

Science.gov (United States)

Yogodzinski, G. M.; Lees, J. M.; Churikova, T. G.; Dorendorf, F.; Wöerner, G.; Volynets, O. N.

2001-01-01

Most island-arc magmatism appears to result from the lowering of the melting point of peridotite within the wedge of mantle above subducting slabs owing to the introduction of fluids from the dehydration of subducting oceanic crust. Volcanic rocks interpreted to contain a component of melt (not just a fluid) from the subducting slab itself are uncommon, but possible examples have been recognized in the Aleutian islands, Baja California, Patagonia and elsewhere. The geochemically distinctive rocks from these areas, termed `adakites', are often associated with subducting plates that are young and warm, and therefore thought to be more prone to melting. But the subducting lithosphere in some adakite locations (such as the Aleutian islands) appears to be too old and hence too cold to melt. This implies either that our interpretation of adakite geochemistry is incorrect, or that our understanding of the tectonic context of adakites is incomplete. Here we present geochemical data from the Kamchatka peninsula and the Aleutian islands that reaffirms the slab-melt interpretation of adakites, but in the tectonic context of the exposure to mantle flow around the edge of a torn subducting plate. We conclude that adakites are likely to form whenever the edge of a subducting plate is warmed or ablated by mantle flow. The use of adakites as tracers for such plate geometry may improve our understanding of magma genesis and thermal structure in a variety of subduction-zone environments.

Shed vortex structure and phase-averaged velocity statistics in symmetric/asymmetric turbulent flat plate wakes

Science.gov (United States)

Rai, Man Mohan

2018-05-01

The near wake of a flat plate is investigated via direct numerical simulations. Many earlier experimental investigations have used thin plates with sharp trailing edges and turbulent boundary layers to create the wake. This results in large θ/DTE values (θ is the boundary layer momentum thickness toward the end of the plate and DTE is the trailing edge thickness). In the present study, the emphasis is on relatively thick plates with circular trailing edges (CTEs) resulting in θ/D values less than one (D is the plate thickness and the diameter of the CTE) and vigorous vortex shedding. The Reynolds numbers based on the plate length and D are 1.255 × 106 and 10 000, respectively. Two cases are computed: one with turbulent boundary layers on both the upper and lower surfaces of the plate (statistically the same, symmetric wake, Case TT) and the other with turbulent and laminar boundary layers on the upper and lower surfaces, respectively (asymmetric case, Case TL). The data and understanding obtained are of considerable engineering interest, particularly in turbomachinery where the pressure side of an airfoil can remain laminar or transitional because of a favorable pressure gradient and the suction side is turbulent. Shed-vortex structure and phase-averaged velocity statistics obtained in the two cases are compared here. The upper negative shed vortices in Case TL (turbulent separating boundary layer) are weaker than the lower positive ones (laminar separating boundary layer) at inception (a factor of 1.27 weaker in terms of peak phase-averaged spanwise vorticity at the first appearance of a peak). The upper vortices weaken rapidly as they travel downstream. A second feature of interest in Case TL is a considerable increase in the peak phase-averaged, streamwise normal intensity (random component) with increasing streamwise distance (x/D) that occurs near the positive vortex cores. This behavior is observed for a few diameters in the near wake. This is counter to

Gentilly 2 divider plate replacement

International Nuclear Information System (INIS)

Forest, J.; Klisel, E.; McClellan, G.; Schnelder, W.

1995-01-01

The steam generators at the Gentilly 2 Nuclear Plant in operation since 1983 were built with primary divider plates of a bolted panel configuration. During a routine outage inspection, it was noted that two bolts had dislodged from the divider and were located lying in the primary head. Subsequent inspections revealed erosion damage to a substantial number of divider plate bolts and to a lesser extent, to the divider plate itself. After further inspection and repair the units were returned to operation, however, it was determined that a permanent replacement of the primary divider plates was going to be necessary. After evaluation of various options, it was decided that the panel type dividers would be replaced with a single piece floating design. The divider itself was to be of a one piece all-welded arrangement to be constructed from individual panels to be brought in through the manways. In view of the strength limitations of the bolted attachment of the upper seat bar to the tubesheet, a new welded seat bar was provided. To counteract erosion concerns, the new divider is fitted with erosion resistant inserts or weld buildup and with improved sealing features in order to minimize leakage and erosion. At an advanced stage in the design and manufacture of the components, the issue of divider strength during LOCA conditions came into focus. Analysis was performed to determine the strength and/or failure characteristics of the divider to a variety of small and large LOCA conditions. The paper describes the diagnosis of the original divider plates and the design, manufacture, field mobilization, installation and subsequent operation of the replacement divider plates. (author)

Iron speciation and mineral characterization of upper Jurassic reservoir rocks in the Minhe Basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiangxian; Zheng, Guodong, E-mail: gdzhbj@mail.iggcas.ac.cn; Xu, Wang [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Liang, Minliang [Chinese Academy of Geological Sciences, Institute of Geomechanics, Key Lab of Shale Oil and Gas Geological Survey (China); Fan, Qiaohui; Wu, Yingzhong; Ye, Conglin [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Shozugawa, Katsumi; Matsuo, Motoyuki [The University of Tokyo, Graduate School of Arts and Sciences (Japan)

2016-12-15

Six samples from a natural outcrop of reservoir rocks with oil seepage and two control samples from surrounding area in the Minhe Basin, northwestern China were selectively collected and analyzed for mineralogical composition as well as iron speciation using X-ray powder diffraction (XRD) and Mössbauer spectroscopy, respectively. Iron species revealed that: (1) the oil-bearing reservoir rocks were changed by water-rock-oil interactions; (2) even in the same site, there was a different performance between sandstone and mudstone during the oil and gas infusion to the reservoirs; and (3) this was evidence indicating the selective channels of hydrocarbon migration. In addition, these studies showed that the iron speciation by Mössbauer spectroscopy could be useful for the study of oil and gas reservoirs, especially the processes of the water-rock interactions within petroleum reservoirs.

Gentilly-2 and Point Lepreau divider plate replacement

International Nuclear Information System (INIS)

Schneider, W.; McClellan, G.; Weston, S.

1996-01-01

The steam generators at Hydro Quebec's Gentilly-2 and New Brunswick Power's Point Lepreau Nuclear Plants have been in operation since 1983, and were built with primary divider plates of a bolted panel configuration. During a routine outage inspection at Gentilly-2, it was noted that two bolts had dislodged from the divider plate and were located lying in the primary head. Subsequent inspections revealed erosion damage to a a substantial number of divider plate bolts and to a lesser extent, to the divider plate itself. After further inspection and repair the units were returned to operation, however, it was determined that a permanent replacement of the primary divider plates was going to be necessary. Upon evaluation of various options, it was decided that the panel type divider plates would be replaced with a single piece floating design. The divider plate itself was to be of one piece all-welded arrangement to be constructed from individual panels to be brought in through the manways. In view of the strength limitations of the bolted attachment of the upper seat bar to the tubesheet, a new welded seat was was provided. To counteract erosion concerns, the new divider plate is fitted with erosion resistant inserts of weld buildup and with improved sealing features in order to minimize leakage and erosion. At an advanced stage in the design and manufacture of the components, the issue of divider plate strength during loss of coolant accident (LOCA) conditions came into focus. Analysis was performed to determine the strength and/or failure characteristics of the divider plate to a variety of small and large LOCA conditions. Subsequently, Point Lepreau decided to replace their divider plates to address LOCA concerns. The paper describes the diagnosis of the original divider plates and the design. manufacture, field mobilization, installation and subsequent operation of the replacement divider plates. (author)

Rapid Grain Size Reduction in the Upper Mantle at a Plate Boundary

Science.gov (United States)

Kidder, S. B.; Scott, J.; Prior, D. J.; Lubicich, E. J.

2017-12-01

A few spinel peridotite xenoliths found near the Alpine Fault, New Zealand, exhibit a mylonitic texture and, locally, an extremely fine 30 micron grain size. The harzburgite xenoliths were emplaced in a 200 km-long elongate dike zone interpreted as a gigantic tension fracture or Reidel shear associated with Alpine Fault initiation 25 Ma. The presence of thin ( 1 mm) ultramylonite zones with px-ol phase mixing and fine grain sizes, minimal crustal-scale strain associated with the dike swarm, and the absence of mylonites at four of the five xenolith localities associated with the dike swarm indicate that upper mantle deformation was highly localized. Strings of small, recrystallized grains (planes in 3D) are found in the interiors of olivine porphyroclasts. In some cases, bands 1-2 grains thick are traced from the edges of olivine grains and terminate in their interiors. Thicker zones of recrystallized grains are also observed crossing olivine porphyroclasts without apparent offset of the unrecrystallized remnants of the porphyroclasts. We suggest a brittle-plastic origin for these features since the traditional recrystallization mechanisms associated with dislocation creep require much more strain than occurred within these porphyroclasts. Analogous microstructures in quartz and feldspar in mid-crust deformation zones are attributed to brittle-plastic processes. We hypothesize that such fine-grained zones were the precursors of the observed, higher-strain ultramylonite zones. Given the size of the new grains preserved in the porphyroclasts ( 100 micron) and a moho temperature > 650°C, grain growth calculations indicate that the observed brittle-plastic deformation occurred <10,000 yrs. prior to eruption. It is likely then that either brittle-plastic deformation was coeval with the ductile shearing occurring in the ultramylonite bands, or possibly, if deformation can be separated into brittle-plastic (early) and ductile (later) phases, that the entire localization

Petroleum systems of the Upper Magdalena Valley, Colombia

Energy Technology Data Exchange (ETDEWEB)

Sarmiento, L.F.; Rangel, A. [Instituto Colombiano del Petroleo, Bucaramanga (Colombia). ECOPETROL

2004-03-01

In the Upper Magdalena Valley, Colombia, four petroleum systems were identified. Two petroleum systems are located in the Girardot sub-basin and the other two in the Neiva sub- basin. Limestones laterally changing to shales of the lower part of the Villeta Gp, deposited during Albian and Turonian marine flooding events, constitutes the main source rocks of the oil families. These rocks contain 1-4% TOC and type II kerogen. The littoral quartz arenites of the Caballos (Albian) and Monserrate (Maastrichtian) Fms. are the main reservoir rocks. Seal rocks are Cretaceous and Paleocene shales. Overburden includes the Cretaceous rocks and the Tertiary molasse deposited simultaneously with development of two opposite verging thrust systems during Cenozoic time. These deformation events were responsible for trap creation. Except for the Villarrica area, where the source rock reached maturity during the Paleocene, generation occurred during Miocene. Two oil families are identified, each in both sub-basins: One derived from a clay-rich source and the second from a carbonate-rich source rock lithofacies of the lower part of Villeta Gp. Geochemical source-rock to oil correlations are demonstrated for the three of the petroleum systems. Up-dip lateral migration distances are relatively short and faults served as vertical migration pathways. A huge amount of oil was probably degraded at surface, as a result of Miocene deformation and erosion. (author)

Simulating faults and plate boundaries with a transversely isotropic plasticity model

Science.gov (United States)

Sharples, W.; Moresi, L. N.; Velic, M.; Jadamec, M. A.; May, D. A.

2016-03-01

In mantle convection simulations, dynamically evolving plate boundaries have, for the most part, been represented using an visco-plastic flow law. These systems develop fine-scale, localized, weak shear band structures which are reminiscent of faults but it is a significant challenge to resolve the large- and the emergent, small-scale-behavior. We address this issue of resolution by taking into account the observation that a rock element with embedded, planar, failure surfaces responds as a non-linear, transversely isotropic material with a weak orientation defined by the plane of the failure surface. This approach partly accounts for the large-scale behavior of fine-scale systems of shear bands which we are not in a position to resolve explicitly. We evaluate the capacity of this continuum approach to model plate boundaries, specifically in the context of subduction models where the plate boundary interface has often been represented as a planar discontinuity. We show that the inclusion of the transversely isotropic plasticity model for the plate boundary promotes asymmetric subduction from initiation. A realistic evolution of the plate boundary interface and associated stresses is crucial to understanding inter-plate coupling, convergent margin driven topography, and earthquakes.

Morphologic and radiologic data of isolated vertebral end-plates under particular consideration of radiodensitometry

International Nuclear Information System (INIS)

Unflath, U.

1979-01-01

The intention was to find examination techniques for macroscopico-morphological diagnosis, for quantification of the concavity and methods for roentgenologico-densitometric analysis of vertebral end-plates. The following factors were used for macromorphologic diagnosis: osteophytes, ridge constitution, ridge transition, cribriform plate and concavity. The radiodensitometric analysis comprised investigation of bone density, anisotropy and ridge mineralisation. The specimen were radiographed on a mammograph together with calcium chloride solutions of increasing concentration. Statistically significant differences in the behaviour of basal and upper plates were not observed. With reference to the factors osteophytes and ridge constitution the basal plates seem to be morphologically more variable than the upper plates. It resulted that the features absolute concavity and concavity quotient are highly appropriate factors to document the constitution of the isolated vertebral end-plates. Also the features density, anisotropy and ridge mineralisation were found to be useful for documentation. The result of data correlation was that high concavity quotients are accompanied by macroscopically medium- to small-sized pores. Density and anisotropy of the overall profiles do not show correlation, but voluminous cribriform laminae tend to develop more inhomogenic structures. As to be expected, bone density increases with macroscopic fine porosity. The higher the concavity quotient is, the smaller are the values for density, ridge mineralisation and anisotropy. Thus a high degree of vertebral end-plate concavity indicates reduced bone density and lower mineral content. (orig./MG) [de

Poisson's Ratio and Auxetic Properties of Natural Rocks

Science.gov (United States)

Ji, Shaocheng; Li, Le; Motra, Hem Bahadur; Wuttke, Frank; Sun, Shengsi; Michibayashi, Katsuyoshi; Salisbury, Matthew H.

2018-02-01

Here we provide an appraisal of the Poisson's ratios (υ) for natural elements, common oxides, silicate minerals, and rocks with the purpose of searching for naturally auxetic materials. The Poisson's ratios of equivalently isotropic polycrystalline aggregates were calculated from dynamically measured elastic properties. Alpha-cristobalite is currently the only known naturally occurring mineral that has exclusively negative υ values at 20-1,500°C. Quartz and potentially berlinite (AlPO4) display auxetic behavior in the vicinity of their α-β structure transition. None of the crystalline igneous and metamorphic rocks (e.g., amphibolite, gabbro, granite, peridotite, and schist) display auxetic behavior at pressures of >5 MPa and room temperature. Our experimental measurements showed that quartz-rich sedimentary rocks (i.e., sandstone and siltstone) are most likely to be the only rocks with negative Poisson's ratios at low confining pressures (≤200 MPa) because their main constituent mineral, α-quartz, already has extremely low Poisson's ratio (υ = 0.08) and they contain microcracks, micropores, and secondary minerals. This finding may provide a new explanation for formation of dome-and-basin structures in quartz-rich sedimentary rocks in response to a horizontal compressional stress in the upper crust.

A preliminary study on the long-term geologic stability for deep geological disposal of high level radioactive waste in Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, Chun Soo; Bae, Dae Seok; Kim, Kyung Su; Park, Byoung Yoon; Koh, Young Kown [Korea Atomic Energy Research Institute, Taejeon (Korea)

2000-03-01

Geology of the Korean peninsula could be grouped by 7 rock types such as plutonic rocks, crystalline gneisses, metasedimentary rocks, Paleozoic and Mesozoic sedimentary rocks, porous and massive volcanic rocks. The plutonic rock type is the largest rock groups occupying about 35.2% over the peninsula. Tectonic movement could be classified as four great stages as Precambrian, Songnim, Daebo and Bulkuksa even though the ambiguous of prior Songnim. It would be supposed to deep relationship between tectonic movement, orogeny and magmatism. And also, the magmatism within the peninsula could be divided into 5 stages such as 1st stage of Precambrian(>570Ma), 2nd stage of late Paleozoic(>250Ma), 3rd stage of early to mid Mesozoic(200-300Ma), 4th stage of late Mesozoic(135-60Ma) and 5th stage of post early Tertiary(50Ma>). In the seismicities, the peninsula has some characteristics that of the intra-plate seismic characteristics located at south eastern part of the Eurasian plate apart from the boundary of the Pacific and Philippine plate. Eurasian plate is under the two stress direction acting eastward stresses induced the collision of Indo- Australlian plate and westward stresses due to the subduction of due the Pacific and Philippine plate. For the purpose of the quantitative analysis for the safety assessment of HLW disposal, it would be desired to have the long range approach concept for the characterization of FEPs such as upper stated including climate, sae level change, uplift and subsidence, erosion and sedimentation. 38 refs., 18 figs., 25 tabs. (Author)

Study on Nd and Sr isotopes of Yianshanian mafic rocks in east Lanling area and their implication

International Nuclear Information System (INIS)

Zhang Shuming; Wu Jianhua; Zhou Weixun

2003-01-01

East Nanling's Yianshanian mafic magna activity can be divided into four phase. The four phase are the Middle Jurassic, the Late Jurassic, the Early Cretaceous and the Late Cretaceous. They are also four important episodes of extensional activities. The four phase mafic rock possess similar Nd-Sr isotope characteristics, high I Sr (commonly from 0.705 to 0.710) and ε Nd values change range wide (from -7.90 to 5.16). It shows crust-mantle mixed magma origin character. The mafic rock possess the character of within-plate basalts,indicated that they are formed within-plate, and showed there were post-orogenic phase at the early Yianshanian's Middle Jurassic in east Nanling area. The rocks formed pattern is mafic magma rise to the crust bottom, were contaminate by crustal materials, and formed in the setting of lithosphere extended and crust extension. East Nanling's Yianshanian magna activity is mainly magma event concern with mantle magma underplating. (authors)

Petrology of blueschist facies metamorphic rocks of the Meliata Unit

Directory of Open Access Journals (Sweden)

Faryad Shah Wali

1997-06-01

Full Text Available Meliata blueschists originated from basalts, limestones, pelites, psammitic and amphibolite facies basement rocks. Compositionally, the metabasalts have a geochemical signature mostly indicative of a transitional arc-MORB origin, but some mafic rocks having affinity with within plate basalts also present. The mafic blueschists consist of blue amphibole, epidote and albite, rarely also garnet, Na-pyroxene and chloritoid. Apart from phengite and quartz the metapelites and metapsammites contain one or more of the minerals: chloritoid, paragonite, glaucophane, albite, chlorite, occasionally also Na-pyroxene and garnet. Amphibolite facies rocks contain relic garnet, plagioclase and hornblende, the latter two replaced by albite and blue amphibole, respectively. The zoning patterns of blue amphibole, garnet and chloritoid suggest their formation during prograde stage of metamorphism. P-T conditions of meta-morphism are estimated to be about 350-460 oC and 10-12 kbar.

Frictional property of rocks in the Izu-Bonin-Mariana Forearc under high temperature and pressure conditions

Science.gov (United States)

Hyodo, G.; Takahashi, M.; Saito, S.; Hirose, T.

2014-12-01

The Kanto region in central Japan lies atop of three tectonic plates: the North American Plate, the Pacific Plate, and the Philippine Sea Plate. The collision and subduction of the Izu-Bonin-Mariana (IBM) arc on the Philippine Sea Plate into the Kanto region results in occurring the different type of earthquakes, including seismic slip (e.g., the Kanto earthquake) and aseismic creep (i.e., slow earthquakes around the Boso peninsula). The seismic and aseismic slip seems to generate side by side at almost same depth (probably nearly same P-T conditions). This study focus on frictional property of incoming materials to be subducted into the Kanto region, in order to examine a hypothesis that the different types of slips arise from different input materials. Thus, we have performed friction experiments on rocks that constitute the IBM forearc using a high P-T gas medium apparatus at AIST. We sampled five rocks (marl, boninite, andesite, sheared serpentinite and serpentinized dunite) recovered from the IBM forearc by Leg 125, Ocean Drilling Program (ODP Site 784, 786). The rocks were crushed and sieved into 10˜50 µm in grain size. Experiments were conducted at temperature of 300○C, confining pressure of 156 MPa, pore pressure of 60 MPa and axial displacement rates of 0.1 and 1 µm/s. For marl, andesite and boninite, a periodic stick-slip behavior appears at 1 µm/s. Rise time of the stick-slip behaviors are quite long (3.1, 9.9 and 14.2 sec, for marl, andesite and boninite, respectively). We called such events as a "slow stick-slip". Similar slow stick-slip behaviors were observed in previous studies (Noda and Shimamoto, 2010; Okazaki, 2013; Kaproth and Marone, 2013), but this is first time to recognize this characteristic slip behavior in sedimentary and igneous rocks. Although it is difficult to discuss the diverse slip behaviors observed at the Kanto region based on our limited experimental results, we will examine the conditions where the transition between

Finite Element Analysis of Circular Plate using SolidWorks

International Nuclear Information System (INIS)

Kang, Yeo Jin; Jhung, Myung Jo

2011-01-01

Circular plates are used extensively in mechanical engineering for nuclear reactor internal components. The examples in the reactor vessel internals are upper guide structure support plate, fuel alignment plate, lower support plate etc. To verify the structural integrity of these plates, the finite element analyses are performed, which require the development of the finite element model. Sometimes it is very costly and time consuming to make the model especially for the beginners who start their engineering job for the structural analysis, necessitating a simple method to develop the finite element model for the pursuing structural analysis. Therefore in this study, the input decks are generated for the finite element analysis of a circular plate as shown in Fig. 1, which can be used for the structural analysis such as modal analysis, response spectrum analysis, stress analysis, etc using the commercial program Solid Works. The example problems are solved and the results are included for analysts to perform easily the finite element analysis of the mechanical plate components due to various loadings. The various results presented in this study would be helpful not only for the benchmark calculations and results comparisons but also as a part of the knowledge management for the future generation of young designers, scientists and computer analysts

Alkali ion migration between stacked glass plates by corona discharge treatment

Energy Technology Data Exchange (ETDEWEB)

Kawaguchi, Keiga [Research Institute for Electronic Science, Hokkaido University, N20 W10, Kita-ku, Sapporo, Hokkaido 001-0020 (Japan); Suzuki, Toshio [Research Center, Asahi Glass Co., Ltd., 1150 Hazawa-cho, Kanagawa-ku, Yokohama, Kanagawa 221-8755 (Japan); Ikeda, Hiroshi [Art, Science and Technology Center for Cooperative Research, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Sakai, Daisuke [Department of Electrical and Electronic Engineering, Kitami Institute of Technology, 165 Koen-cho, Kitami, Hokkaido 090-8507 (Japan); Funatsu, Shiro; Uraji, Keiichiro [Production Technology Center, Asahi Glass Co., Ltd., 1-1 Suehiro-cyo, Tsurumiku, Yokohama, Kanagawa 230-0045 (Japan); Yamamoto, Kiyoshi [Research Center, Asahi Glass Co., Ltd., 1150 Hazawa-cho, Kanagawa-ku, Yokohama, Kanagawa 221-8755 (Japan); Harada, Kenji [Department of Computer Science, Kitami Institute of Technology, 165 Koen-cho, Kitami, Hokkaido 090-8507 (Japan); Nishii, Junji, E-mail: nishii@es.hokudai.ac.jp [Research Institute for Electronic Science, Hokkaido University, N20 W10, Kita-ku, Sapporo, Hokkaido 001-0020 (Japan)

2015-05-30

Highlights: • Two stacked glass plates with a 1 mm gap were treated by corona discharge. • Spatial migration of alkali ion over the gap was demonstrated. • Hydrogen gas was necessary for uniform migration. • Surface modification was done with this process without high temperature or vacuum. - Abstract: Corona discharge reflects the spatial migration of alkali ions over a gap between two glass plates. This study examined stacked glass plates containing different alkali ions treated with the corona discharge plasma generated by applied voltage of 4.5 kV at 200 °C. Protons generated at the anode electrode penetrate into the potassium-ion-containing upper glass plate, which is located 5 mm below the anode electrode. Potassium ions intruded into the lower glass plate containing sodium ions placed on the cathode electrode, even over a 1 mm gap separating the plates. Finally, the sodium ion discharged on the cathode electrode. The hydrogen atmosphere was effective at inhibiting the potassium ion reaction with ambient gases during the spatial migration between the two glass plates.

A discussion for the evolution model of Pb isotope of the upper mantle in western Yunnan and its interpretation to the lead isotopic compositions of the regional alkali-rich porphyries and their related rocks

International Nuclear Information System (INIS)

Wu Kaixing; Hu Ruizhong; Bi Xianwu; Zhang Qian; Peng Jiantang

2003-01-01

Thirty Pb isotope data of the upper mantle in the area of western Yunnan have the similar trends with the Stacey-Kramers' two stage model growth curves but apparently deviate from it on the lead isotope composition programs, which may suggest Pb isotope of the upper mantle in the area of western Yunnan might have two stage evolution history though not fit very well to the Stacey-Kramers' two stage model growth curves. In this paper, a two-stage growth curves which can better fit the Pb isotope data was constructed based on the lead isotope data of the upper mantle in western Yunnan and the principle that Stacey and Kramers constructed the two-stage model and a reasonable interpretation was given to the lead isotopic compositions of the regional alkali-rich porphyries and their related rocks using the model. (authors)

Holocene faulting in the Bellingham forearc basin: upper-plate deformation at the northern end of the Cascadia subduction zone

Science.gov (United States)

Kelsey, Harvey M.; Sherrod, Brian L.; Blakely, Richard J.; Haugerud, Ralph A.

2013-01-01

The northern Cascadia forearc takes up most of the strain transmitted northward via the Oregon Coast block from the northward-migrating Sierra Nevada block. The north-south contractional strain in the forearc manifests in upper-plate faults active during the Holocene, the northern-most components of which are faults within the Bellingham Basin. The Bellingham Basin is the northern of four basins of the actively deforming northern Cascadia forearc. A set of Holocene faults, Drayton Harbor, Birch Bay, and Sandy Point faults, occur within the Bellingham Basin and can be traced from onshore to offshore using a combination of aeromagnetic lineaments, paleoseismic investigations and scarps identified using LiDAR imagery. With the recognition of such Holocene faults, the northernmost margin of the actively deforming Cascadia forearc extends 60 km north of the previously recognized limit of Holocene forearc deformation. Although to date no Holocene faults are recognized at the northern boundary of the Bellingham Basin, which is 15 km north of the international border, there is no compelling tectonic reason to expect that Holocene faults are limited to south of the international border.

Structural context and variation of ocean plate stratigraphy, Franciscan Complex, California: insight into mélange origins and subduction-accretion processes

Science.gov (United States)

Wakabayashi, John

2017-12-01

The transfer (accretion) of materials from a subducting oceanic plate to a subduction-accretionary complex has produced rock assemblages recording the history of the subducted oceanic plate from formation to arrival at the trench. These rock assemblages, comprising oceanic igneous rocks progressively overlain by pelagic sedimentary rocks (chert and/or limestone) and trench-fill clastic sedimentary rocks (mostly sandstone, shale/mudstone), have been called ocean plate stratigraphy (OPS). During accretion of OPS, megathrust slip is accommodated by imbricate faults and penetrative strain, shortening the unit and leading to tectonic repetition of the OPS sequence, whereas OPS accreted at different times are separated by non-accretionary megathrust horizons. The Franciscan subduction complex of California accreted episodically over a period of over 150 million years and incorporated OPS units with a variety of characteristics separated by non-accretionary megathrust horizons. Most Franciscan OPS comprises MORB (mid-ocean-ridge basalt) progressively overlain by chert and trench-fill clastic sedimentary rocks that are composed of variable proportions of turbidites and siliciclastic and serpentinite-matrix olistostromes (sedimentary mélanges). Volumetrically, the trench-fill component predominates in most Franciscan OPS, but some units have a significant component of igneous and pelagic rocks. Ocean island basalt (OIB) overlain by limestone is less common than MORB-chert assemblages, as are abyssal serpentinized peridotite slabs. The earliest accreted OPS comprises metabasite of supra-subduction zone affinity imbricated with smaller amounts of metaultramafic rocks and metachert, but lacking a clastic component. Most deformation of Franciscan OPS is localized along discrete faults rather than being distributed in the form of penetrative strain. This deformation locally results in block-in-matrix tectonic mélanges, in contrast to the sedimentary mélanges making up part of

A possible connection between post-subduction arc magmatism and adakite-NEB rock association in Baja California, Mexico

Science.gov (United States)

Castillo, P. R.

2007-05-01

Late Miocene to Recent arc-related magmatism occurs in Baja California, Mexico despite the cessation of plate subduction along its western margin at ~12.5 Ma. It includes calcalkaline and K-rich andesites, tholeiitic basalts and basaltic andesites, alkalic basalts similar to many ocean island basalts (OIB), magnesian and basaltic andesites with adakitic affinity (bajaiites), adakites, and Nb-enriched basalts (NEB). A popular model for the close spatial and temporal association of adakite (plus bajaiite) and NEB in Baja California is these are due to melting of the subducted Farallon/Cocos plate, which in turn is caused by the influx of hot asthenospheric mantle through a window created in the subducted slab directly beneath the Baja California peninsula [e.g., Benoit, M. et. al. (2002) J. Geol. 110, 627-648; Calmus, T. et al. (2003) Lithos 66, 77-105]. Here I propose an alternative model for the cause of post-subduction magmatism in Baja California in particular and origin of adakite-NEB rock association in general. The complicated tectonic configuration of the subducting Farallon/Cocos plate and westward motion of the North American continent caused western Mexico to override the hot, upwelling Pacific mantle that was decoupled from the spreading centers abandoned west of Baja California. The upwelling asthenosphere is best manifested east of the peninsula, beneath the Gulf of California, and is most probably due to a tear or window in the subducted slab there. The upwelling asthenosphere is compositionally heterogeneous and sends materials westward into the mantle wedge beneath the peninsula. These materials provide sources for post-subduction tholeiitic and alkalic magmas. Portions of tholeiitic magmas directly erupted at the surface produce tholeiitic lavas, but some get ponded beneath the crust. Re-melting and/or high-pressure fractional crystallization of the ponded tholeiitic magmas generate adakitic rocks. Alkalic magmas directly erupted at the surface

Lighting system for the lower core plate of a nuclear reactor

International Nuclear Information System (INIS)

Feuillet, P.; Bonin, J.P.

1986-01-01

The invention proposes a grazing lighting system for the lower core plate, creating an excellent contrast and offering a good estimation of the relief; it can stay at the same place during the whole or at least the greater part of the core refueling operation. This lighting system is proposed for a reactor of which the lower core plate has fuel assembly centering elements. It has a sealed vessel with a transparent side wall containing several lights independently controlled and each one illuminating a sector of its wall. The vessel has a bottom aimed at resting on the lower plate and provided with centering and holding means acting with several of the said centering means through the plate, and/or apertures for coolant through the plate, and an upper container provided with gripping and handling elements and sealed conduits for electrical cables feeding the lights [fr

Aqueous Alteration of Endeavour Crater Rim Apron Rocks

Science.gov (United States)

Ming, D. W.; Mittlefehldt, D. W.; Gellert, R.; Clark, B. C.; Morris, R. V.; Yen, A. S.; Arvidson, R. E.; Crumpler, L. S.; Farrand, W. H.; Grant, J. A., III; Jolliff, B. L.; Parker, T. J.; Peretyazhko, T.

2014-12-01

Mars Exploration Rover Opportunity is exploring Noachian age rocks of the rim of 22 km diameter Endeavour crater. Overlying the pre-impact lithologies and rim breccias is a thin apron of fine-grained sediments, the Grasberg fm, forming annuli on the lower slopes of rim segments. Hesperian Burns fm sandstones overly the Grasberg fm. Grasberg rocks have major element compositions that are distinct from Burns fm sandstones, especially when comparing interior compositions exposed by the Rock Abrasion Tool. Grasberg rocks are also different from Endeavour rim breccias, but have general compositional similarities to them. Grasberg sediments are plausibly fine-grained materials derived from the impact breccias. Veins of CaSO4 transect Grasberg fm rocks demonstrating post-formation aqueous alteration. Minor/trace elements show variations consistent with mobilization by aqueous fluids. Grasberg fm rocks have low Mn and high Fe/Mn ratios compared to the other lithologies. Manganese likely was mobilized and removed from the Grasberg host rock by redox reactions. We posit that Fe2+ from acidic solutions associated with formation of the Burns sulfate-rich sandstones acted as an electron donor to reduce more oxidized Mn to Mn2+. The Fe contents of Grasberg rocks are slightly higher than in other rocks suggesting precipitation of Fe phases in Grasberg materials. Pancam spectra show that Grasberg rocks have a higher fraction of ferric oxide minerals than other Endeavour rim rocks. Solutions transported Mn2+ into the Endeavour rim materials and oxidized and/or precipitated it in them. Grasberg has higher contents of the mobile elements K, Zn, Cl, and Br compared to the rim materials. Similar enrichments of mobile elements were measured by the Spirit APXS on West Spur and around Home Plate in Gusev crater. Enhancements in these elements are attributed to interactions of hydrothermal acidic fluids with the host rocks. Interactions of fluids with the Grasberg fm postdate the genesis

The ongoing search for the oldest rock on the Danish island of Bornholm: new U-Pb zircon ages for a quartz-rich xenolith and country rock from the Svaneke Granite

DEFF Research Database (Denmark)

Waight, Tod Earle; Serre, Simon H.; Næsby, Sebastian H.

2017-01-01

Previous geochronological studies on the Danish island of Bornholm have not identified any rocks older than c. 1.46 Ga. New LA-ICP-MS U-Pb zircon ages are presented for a xenolith within, and the country rock gneiss adjacent to, the Svaneke Granite on Bornholm. The xenolith is fine......-grained and quartz-rich and was likely derived from either a quartz-rich sedimentary protolith or a hydrothermally altered felsic volcanic rock. The relatively fine-grained felsic nature of the country rock gneiss and the presence of large zoned feldspars that may represent phenocrysts suggest its protolith may have...... been a felsic volcanic or shallow intrusive rock. A skarn-like inclusion from a nearby locality likely represents an originally carbonate sediment and is consistent with supracrustal rocks being present at least locally. Zircon data from the xenolith define an upper intercept age of 1483 ± 12 Ma (2σ...

Deformation mechanisms and melt nano-structures in experimentally deformed olivine-orthopyroxene rocks with low melt fractions

NARCIS (Netherlands)

Kloe, P.A. de

2001-01-01

The major part of the Earth’s upper mantle is thought to be solid, with some regions in the mantle where the rocks contain a small melt fraction These partially molten rocks are associated with important geological processes such as magma production beneath mid-oceanic ridges and may also play an

A new energy-absorbing bolt for rock support in high stress rock masses

Energy Technology Data Exchange (ETDEWEB)

Charlie Chunlin Li [Norwegian University of Science and Technology (NTNU) (Norway)

2010-04-15

An energy-absorbing rock support device, called a D bolt, has been recently developed to counteract both burst-prone and squeezing rock conditions that occur during underground excavation. The bolt is a smooth steel bar with a number of anchors along its length. The anchors are firmly fixed within a borehole using either cement grout or resin, while the smooth sections of the bolt between the anchors may freely deform in response to rock dilation. Failure of one section does not affect the reinforcement performance of the other sections. The bolt is designed to fully use both the strength and the deformation capacity of the bolt material along the entire length. The bolt has large load-bearing and deformation capacities. Static pull tests and dynamic drop tests show that the bolt length elongates by 14-20% at a load level equal to the strength of the bolt material, thereby absorbing a large amount of energy. The impact average load of a 20 mm D bolt is 200-230 kN, with only a small portion of the load transferred to the bolt plate. The cumulative dynamic energy absorption of the bolt is measured to be 47 kJ/m. D bolts were tested in three deep mines. Filed measurements show that D bolts are loaded less than rebar bolts. This paper presents the layout and principle of the D bolt, and corresponding results from static, dynamic, and field tests.

Petrological-geochemical characteristics of coarse-grained clastic sedimentary rocks of Quantou Formation, Cretaceous in Songliao basin and their geological significance

International Nuclear Information System (INIS)

Wang Gan; Zhang Bangtong

2005-01-01

Clastic sedimentary rocks of Quantou Formation, Cretaceous in Qing-an area, Songliao basin are mainly composed of sandstone, mudstone and siltstone. The petrological-chemical analysis of clastic sedimentary rocks from Quantou Formation, Cretaceous indicates that their lithology mainly consists of arkose, shale and minor rock debris sandstone and greywacke by chemical classification of bulk elements. REE distribution pattern displays the apparent enrichment of LREE and negative anomaly of Eu and is similar to that of NASC and PAAS. The ratio of trace-element in sedimentary rocks to that of upper crust shows gentle character. All the above features indicate that these sedimentary rocks were slowly deposited under weakly active tectonic setting. They are sediments typical for passive continental margin and active continental margin. It is suggested that material source of clastic sediments of Quantou Formation, Cretaceous in Qing-an area, Songliao basin was originated from Hercynian granite of Zhangguangchai Mountain, and the granite was originated from upper crust. (authors)

Temperature loading and rocks mechanics at final storage of radioactive waste

International Nuclear Information System (INIS)

Leijon, B.; Stephansson, O.

1979-01-01

This report describes the rock mechanical effects - in the far field - from the thermal loading at a final storage of radioactive waste in crystalline rocks. The stress distribution of a two-storey storage is described in more details. The temperature rise in a final storage of radiactive waste will create thermal stresses which may cause a failure of the rock mass, and thereby an increase of its permeability. However, the state of stress in the Earth's crust is able to neutralize the thermal stresses. By this analysis we have been able to demonstrate that the thermal stresses due to heat conduction from the final storage are compensated by the state of stress in the upper part of the crust. The absolute stress, which is the superposition of thermal stress and virgin rock stress, is in all cases found to be below the limit of failure due to frictional resistance between surfaces of constituent blocks in the rock mass. Failure by sliding friction is the most conservative failure criterion for a rock mass. (author)

Waveguide module comprising a first plate with a waveguide channel and a second plate with a raised portion in which a sealing layer is forced into the waveguide channel by the raised portion

Science.gov (United States)

Strassner, II, Bernd H.; Liedtke, Richard; McDonald, Jacob Jeremiah; Halligan, Matthew

2018-04-17

The various technologies presented herein relate to utilizing a sealing layer of malleable material to seal gaps, etc., at a joint between edges of a waveguide channel formed in a first plate and a surface of a clamping plate. A compression pad is included in the surface of the clamping plate and is dimensioned such that the upper surface of the pad is less than the area of the waveguide channel opening on the first plate. The sealing layer is placed between the waveguide plate and the clamping plate, and during assembly of the waveguide module, the compression pad deforms a portion of the sealing layer such that it ingresses into the waveguide channel opening. Deformation of the sealing layer results in the gaps, etc., to be filled, improving the operational integrity of the joint.

Development of S/G Lancing System for Upper Bundle Hydraulic Cleaning

International Nuclear Information System (INIS)

Jeong, Woo Tae; Kim, Suk Tae; Hong, Sung Yull

2005-01-01

Steam generators of nuclear power plants are recommended to be cleaned during plant outages. Various lancing equipments are developed for the cleaning of tube sheet area of nuclear steam generators. However, no lancing system has been developed in Korea for cleaning upper bundle area of steam generators. Therefore, we developed an upper bundle cleaning system for removing sludge deposited on the tube support plates of nuclear steam generators

Rough horizontal plates: heat transfer and hysteresis

Energy Technology Data Exchange (ETDEWEB)

Tisserand, J-C; Gasteuil, Y; Pabiou, H; Castaing, B; Chilla, F [Universite de Lyon, ENS Lyon, CNRS, 46 Allee d' ltalie, 69364 Lyon Cedex 7 (France); Creyssels, M [LMFA, CNRS, Ecole Centrale Lyon, 69134 Ecully Cedex (France); Gibert, M, E-mail: mathieu.creyssels@ec-lyon.fr [Also at MPI-DS (LFPN) Gottingen (Germany)

2011-12-22

To investigate the influence of a rough-wall boundary layer on turbulent heat transport, an experiment of high-Rayleigh convection in water is carried out in a Rayleigh-Benard cell with a rough lower plate and a smooth upper plate. A transition in the heat transport is observed when the thermal boundary layer thickness becomes comparable to or smaller than the roughness height. Besides, at larger Rayleigh numbers than the threshold value, heat transport is found to be increased up to 60%. This enhancement cannot be explained simply by an increase in the contact area of the rough surface since the contact area is increased only by a factor of 40%. Finally, a simple model is proposed to explain the enhanced heat transport.

Acoustic excitation of containment insulation cover plate

International Nuclear Information System (INIS)

Fenech, H.; Rao, A.K.

1978-01-01

An experimental and theoretical program has been implemented by NRC-BNL since 1975 at the University of California, Santa Barbara to assess the reliability of the PCRV thermal insulation cover plate and the possible safety problem caused by the failure of this plate. A typical large HTGR PCRV unit [1160 MW(e)] and thermal insulation class A were selected. The upper core cavity is estimated to be the most critical volume where the noise pressure levels are expected to reach 110 to 130 dB (rel. to 2 x 10 -4 dynes/cm 2 ). The noise spectrum in that cavity is a composite of circulator noise, vortex shedding boundary layer turbulence, and flow impingement. Some anticipated safety related problems associated with the thermal insulation failure are examined

Organic richness and organic matter quality studies of source rocks ...

African Journals Online (AJOL)

The hydrocarbon potential of the Upper Cretaceous units (Maastrichtian Mamu Formation) exposed at Imiegba and environs of the Benin Flank, Western Anambra Basin was assessed by Total Organic Carbon (TOC) and Rock-Eval Pyrolysis Analyses. The investigated sections of the Mamu Formation consist of dark grey to ...

Application of Long Expansion Rock Bolt Support in the Underground Mines of Legnica-Głogów Copper District

Science.gov (United States)

Skrzypkowski, Krzysztof; Korzeniowski, Waldemar; Zagórski, Krzysztof; Dudek, Piotr

2017-09-01

In the underground mines of the Legnica-Głogów Copper District (LGOM) the main way to protect the room excavation is the use of a rock bolt support. For many years, it has proven to be an efficient security measure in excavations which met all safety standards and requirements. The article presents the consumption of the rock bolt support in the Mining Department "Polkowice-Sieroszowice" in the years 2010-2015 as well as the number of bolt supports that were used to secure the excavations. In addition, it shows the percentage of bolt supports that were used to conduct rebuilding work and cover the surface of exposed roofs. One of the factors contributing to the loss of the functionality of bolt supports is corrosion whose occurrence may lead directly to a reduction in the diameter of rock bolt support parts, in particular rods, bearing plates and nuts. The phenomenon of the corrosion of the bolt support and its elements in underground mining is an extremely common phenomenon due to the favorable conditions for its development in mines, namely high temperature and humidity, as well as the presence of highly aggressive water. This involves primarily a decrease in the capacity of bolt support construction, which entails the need for its strengthening, and often the need to perform the reconstruction of the excavation. The article presents an alternative for steel bearing plates, namely plates made using the spatial 3D printing technology. Prototype bearing plates were printed on a 3D printer Formiga P100 using the "Precymit" material. The used printing technology was SLS (Selective Laser Sintering), which is one of the most widely used technologies among all the methods of 3D printing for the short series production of the technical parts of the final product. The article presents the stress-strain characteristic of the long expansion connected rock bolt support OB25 with a length of 3.65 m. A rock bolt support longer than 2.6 m is an additional bolt support in

Comparisons of Different Models on Dynamic Recrystallization of Plate during Asymmetrical Shear Rolling

Directory of Open Access Journals (Sweden)

Tao Zhang

2018-01-01

Full Text Available Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX plays a vital role in grain refinement during hot deformation. Finite element models (FEM coupled with microstructure evolution models and cellular automata models (CA are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation.

Comparisons of Different Models on Dynamic Recrystallization of Plate during Asymmetrical Shear Rolling

Science.gov (United States)

Zhang, Tao; Li, Lei; Lu, Shi-Hong; Gong, Hai; Wu, Yun-Xin

2018-01-01

Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX) plays a vital role in grain refinement during hot deformation. Finite element models (FEM) coupled with microstructure evolution models and cellular automata models (CA) are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation. PMID:29342080

Upper Paleozoic mafic and intermediate volcanic rocks of the Mount Pleasant caldera associated with the Sn-W deposit in southwestern New Brunswick (Canada): Petrogenesis and metallogenic implications

Science.gov (United States)

Dostal, Jaroslav; Jutras, Pierre

2016-10-01

Upper Paleozoic ( 365 Ma) mafic and intermediate volcanic rocks of the Piskahegan Group constitute a subordinate part of the Mount Pleasant caldera, which is associated with a significant polymetallic deposit (tungsten-molybdenum-bismuth zones 33 Mt ore with 0.21% W, 0.1% Mo and 0.08% Bi and tin-indium zones 4.8 Mt with 0.82% Sn and 129 g/t In) in southwestern New Brunswick (Canada). The epicontinental caldera complex formed during the opening of the late Paleozoic Maritimes Basin in the northern Appalachians. The mafic and intermediate rocks make up two compositionally distinct associations. The first association includes evolved rift-related continental tholeiitic basalts, and the second association comprises calc-alkaline andesites, although both associations were emplaced penecontemporaneously. The basalts have low Mg# 0.34-0.40, smooth chondrite-normalized REE patterns with (La/Yb)n 5-6, primitive mantle-normalized trace element patterns without noticeable negative Nb-Ta anomalies, and their ɛNd(T) ranges from + 2.5 to + 2.2. The basalts were generated by partial melting of a transition zone between spinel and garnet mantle peridotite at a depth of 70-90 km. The calc-alkaline andesites of the second association have chondrite-normalized REE patterns that are more fractionated, with (La/Yb)n 7-8.5, but without significant negative Eu anomalies. Compared to the basaltic rocks, they have lower ɛNd(T) values, ranging from + 0.5 to + 1.9, and their mantle-normalized trace element plots show negative Nb-Ta anomalies. The ɛNd(T) values display negative correlations with indicators of crustal contamination, such as Th/La, Th/Nb and SiO2. The andesitic rocks are interpreted to have formed by assimilation-fractional crystallization processes, which resulted in the contamination of a precursor basaltic magma with crustal material. The parent basaltic magma for both suites underwent a different evolution. The tholeiitic basalts experienced shallow-seated fractional

Geologic setting of the St. Catherine basement rocks, Sinai, Egypt

OpenAIRE

Abdel Maksoud, M. A. [محمد علي عبدالمقصود; Khalek, M. L. Abdel; Oweiss, K. A.

1993-01-01

St. Catherine area, some 900 km in size, is dominated by basement rocks Encompassing old continental gneisses, metasediments, greenstone belt, calc-alkaline granites (G-II-granites), rift-related volcanics (RV), and anorogenic within plate granites (G-III-granites). The greenstone belt is composed of subduction-related volcanics (SV) intercalated with metasediments. These volcanics split into older group (moderately metamorphosed) and younger group (slightly metamorphosed). The calc-alkaline ...

Stress accumulation and release at complex transform plate boundaries

Energy Technology Data Exchange (ETDEWEB)

Verdonck, D.; Furlong, K.P. (Pennsylvania State Univ., University Park (United States))

1992-10-01

Finite element methods are used to model the dynamics of deformation along complex transform plate boundaries, specifically the San Andreas fault system, California. Effects of mantle rheology and fault geometry on the stress buildup and release are investigated. No prior knowledge of the earthquake cycle time or amount of fault slip is assumed that the results suggest that the San Andreas fault slips at low shear stress (about 15 MPa). Although the maximum stress on the fault is 15 MPa, models with an upper mantle shear zone deforming entirely by dislocation creep accumulate stresses that exceed 100 MPa, a stress level high enough to drive localized dynamic recrystallization and a shift in dominant deformation mechanism to diffusion creep. Models in which the mantle shear zone deform locally by diffusion creep reach a dynamic steady state where lithospheric shear stresses never exceed the specified fault stress anywhere in the model and indicate that the strength of the upper mantle is an important parameter in the dynamics of plate boundary deformation. 17 refs.

The concurrent emergence and causes of double volcanic hotspot tracks on the Pacific plate

DEFF Research Database (Denmark)

Jones, David T; Davies, D. R.; Campbell, I. H.

2017-01-01

Mantle plumes are buoyant upwellings of hot rock that transport heat from Earth's core to its surface, generating anomalous regions of volcanism that are not directly associated with plate tectonic processes. The best-studied example is the Hawaiian-Emperor chain, but the emergence of two sub......-parallel volcanic tracks along this chain, Loa and Kea, and the systematic geochemical differences between them have remained unexplained. Here we argue that the emergence of these tracks coincides with the appearance of other double volcanic tracks on the Pacific plate and a recent azimuthal change in the motion...... of the plate. We propose a three-part model that explains the evolution of Hawaiian double-track volcanism: first, mantle flow beneath the rapidly moving Pacific plate strongly tilts the Hawaiian plume and leads to lateral separation between high- and low-pressure melt source regions; second, the recent...

Isostatic Model and Isostatic Gravity Anomalies of the Arabian Plate and Surroundings

Science.gov (United States)

Kaban, Mikhail K.; El Khrepy, Sami; Al-Arifi, Nassir

2016-04-01

The isostatic modeling represents one of the most useful "geological" reduction methods of the gravity field. With the isostatic correction, it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. Although there exist several isostatic compensation schemes, it is usually supposed that a choice of the model is not an important factor to first order, since the total weight of compensating masses remains the same. We compare two alternative models for the Arabian plate and surrounding area. The Airy model gives very significant regional isostatic anomalies, which cannot be explained by the upper crust structure or disturbances of the isostatic equilibrium. Also, the predicted "isostatic" Moho is very different from existing seismic observations. The second isostatic model includes the Moho, which is based on seismic determinations. Additional compensation is provided by density variations within the lithosphere (chiefly in the upper mantle). According to this model, the upper mantle under the Arabian Shield is less dense than under the Platform. In the Arabian platform, the maximum density coincides with the Rub' al Khali, one of the richest oil basin in the world. This finding agrees with previous studies, showing that such basins are often underlain by dense mantle, possibly related to an eclogite layer that has caused their subsidence. The mantle density variations might be also a result of variations of the lithosphere thickness. With the combined isostatic model, it is possible to minimize regional anomalies over the Arabian plate. The residual local anomalies correspond well to tectonic structure of the plate. Still very significant anomalies, showing isostatic disturbances of the lithosphere, are associated with the Zagros fold belt, the collision zone of the Arabian and Eurasian plates.

Osmium Isotopic Evolution of the Mantle Sources of Precambrian Ultramafic Rocks

Science.gov (United States)

Gangopadhyay, A.; Walker, R. J.

2006-12-01

The Os isotopic composition of the modern mantle, as recorded collectively by ocean island basalts, mid- oceanic ridge basalts (MORB) and abyssal peridotites, is evidently highly heterogeneous (γ Os(I) ranging from +25). One important question, therefore, is how and when the Earth's mantle developed such large-scale Os isotopic heterogeneities. Previous Os isotopic studies of ancient ultramafic systems, including komatiites and picrites, have shown that the Os isotopic heterogeneity of the terrestrial mantle can be traced as far back as the late-Archean (~ 2.7-2.8 Ga). This observation is based on the initial Os isotopic ratios obtained for the mantle sources of some of the ancient ultramafic rocks determined through analyses of numerous Os-rich whole-rock and/or mineral samples. In some cases, the closed-system behavior of these ancient ultramafic rocks was demonstrated via the generation of isochrons of precise ages, consistent with those obtained from other radiogenic isotopic systems. Thus, a compilation of the published initial ^{187}Os/^{188}Os ratios reported for the mantle sources of komatiitic and picritic rocks is now possible that covers a large range of geologic time spanning from the Mesozoic (ca. 89 Ma Gorgona komatiites) to the Mid-Archean (e.g., ca. 3.3 Ga Commondale komatiites), which provides a comprehensive picture of the Os isotopic evolution of their mantle sources through geologic time. Several Precambrian komatiite/picrite systems are characterized by suprachondritic initial ^{187}Os/^{188}Os ratios (e.g., Belingwe, Kostomuksha, Pechenga). Such long-term enrichments in ^{187}Os of the mantle sources for these rocks may be explained via recycling of old mafic oceanic crust or incorporation of putative suprachondritic outer core materials entrained into their mantle sources. The relative importance of the two processes for some modern mantle-derived systems (e.g., Hawaiian picrites) is an issue of substantial debate. Importantly, however, the

A New Comprehensive Model for Crustal and Upper Mantle Structure of the European Plate

Science.gov (United States)

Morelli, A.; Danecek, P.; Molinari, I.; Postpischl, L.; Schivardi, R.; Serretti, P.; Tondi, M. R.

2009-12-01

We present a new comprehensive model of crustal and upper mantle structure of the whole European Plate — from the North Atlantic ridge to Urals, and from North Africa to the North Pole — describing seismic speeds (P and S) and density. Our description of crustal structure merges information from previous studies: large-scale compilations, seismic prospection, receiver functions, inversion of surface wave dispersion measurements and Green functions from noise correlation. We use a simple description of crustal structure, with laterally-varying sediment and cristalline layers thickness and seismic parameters. Most original information refers to P-wave speed, from which we derive S speed and density from scaling relations. This a priori crustal model by itself improves the overall fit to observed Bouguer anomaly maps, as derived from GRACE satellite data, over CRUST2.0. The new crustal model is then used as a constraint in the inversion for mantle shear wave speed, based on fitting Love and Rayleigh surface wave dispersion. In the inversion for transversely isotropic mantle structure, we use group speed measurements made on European event-to-station paths, and use a global a priori model (S20RTS) to ensure fair rendition of earth structure at depth and in border areas with little coverage from our data. The new mantle model sensibly improves over global S models in the imaging of shallow asthenospheric (slow) anomalies beneath the Alpine mobile belt, and fast lithospheric signatures under the two main Mediterranean subduction systems (Aegean and Tyrrhenian). We map compressional wave speed inverting ISC travel times (reprocessed by Engdahl et al.) with a non linear inversion scheme making use of finite-difference travel time calculation. The inversion is based on an a priori model obtained by scaling the 3D mantle S-wave speed to P. The new model substantially confirms images of descending lithospheric slabs and back-arc shallow asthenospheric regions, shown in

Geological, petrogical and geochemical characteristics of granitoid rocks in Burma: with special reference to the associated WSn mineralization and their tectonic setting

Science.gov (United States)

Zaw, Khin

The granitoid rocks in Burma extend over a distance of 1450 km from Putao, Kachin State in the north, through Mogok, Kyaukse, Yamethin and Pyinmana in the Mandalay Division, to Tavoy and Mergui areas, Tenasserim Division, in the south. The Burmese granitoids can be subdivided into three N-S trending, major belts viz. western granitoid belt, central graniotoid belt and eastern granitoid belt. The Upper Cretaceous-Lower Eocene western belt granitoids are characterized by high-level intrusions associated with porphyry Cu(Au) related, younger volcanics; these plutonic and volcanic rocks are thought to have been emplaced as a magmatic-volcanic arc (inner magmatic-volcanic arc) above an east-dipping, but westwardly migrating, subduction zone related to the prolonged plate convergence which occurred during Upper Mesozoic and Cenozoic. The central granitoid belt is characterized by mesozonal, Mostly Upper Cretaceous to Lower Eocene plutons associated with abundant pegmalites and aplites, numerous vein-type W-Sn deposits and rare co-magmatic volcanics. The country rocks are structurally deformed, metamorphic rocks of greenschist to upper amphibolite facies ranging in age as early as Upper Precambrian to Upper Paleozoic and locally of fossiliferous, metaclastic rocks (Mid Jurassic to Lower Cretaceous). Available K/Ar radiometric data indicate significant and possibly widespread thermal disturbances in the central granitoid belt during the Tertiary (mostly Miocence). In this study, the distribution, lithological, textural and structural characteristics of the central belt granitoids are reviewed, and their mineralogical, petrological, and geochemical features are presented. A brief description of W-Sn ore veins associated with these granitoid plutons is also reported. Present geological, petrological and geochemical evidences demonstrate that the W-Sn related, central belt granitoids are mostly granodiorite and granite which are commonly transformed into granitoid gneisses

Mineral Chemistry and Geochemistry of Volcanic Rocks in The North of Pasinler (Erzurum

Directory of Open Access Journals (Sweden)

Oktay KILIÇ

2009-02-01

Full Text Available In the north of Pasinler (Erzurum, Upper Miocene-Pliocene volcanic rocks crop out. These volcanites are composed of basaltic andesite, andesite, dacite, rhyolite lavas and rhyolitic pyroclastics. The rocks show porphyritic, microlitic porphyritic, hyalo-microlitic porphyritic, vitrophyric, glomeroporphyritic, pilotaxitic and hyalopilitic textures. The investigated volcanites contain plagioclase (An29-80, olivine (Fo65-82, clinopyroxene (augite, orthopyroxene (enstatite, amphibole (Mg#: 0.57-0.71, biotite (phlogopite: 0.44-0.47, annite: 0.33-0.37, sanidine, quartz and opaque mineral (titano-magnetite and ilmenite. The volcanic rocks are calc-alkaline in character and have medium to high-K contents. Major oxide and trace element variations point out open-system magmatic differentiation in the evolution of rocks. Geochemical data indicate an important role of fractionation of phenocryst phases in the rocks during differentiation process. However, it is considered that assimilation±magma mixing might have accompanied to the process. High LILE (K, Rb, Ba, Th and relatively low HFSE (Nb, Ta, Hf, Zr contents of the rocks indicate that these rocks derived from parental magmas carrying subduction signature.

Mechanics and Partitioning of Deformation of the Northwestern Okhostk Plate, Northeast Russia

Science.gov (United States)

Hindle, D.; Mackey, K.; Fujita, K.

2007-12-01

The tectonic evolution and present day deformation of northeastern Russia remains one of the major challenges in plate tectonics. Arguments over the existence of at least a separate Okhotsk plate between North America and Eurasia appear to be resolved on the basis of the latest GPS studies combined with elastic modeling. The question of the mechanical behaviour of the Okhotsk plate, caught between the slowly, obliquely converging North American and Eurasian plates now becomes important. We present an analysis of geological lineaments, micro-seismicity, total seismic moment release and seismic deformation rate and GPS campaign data and global plate tectonic model data (REVEL) to estimate the likelihood of future seismicity and the relative amount of elastic and viscous deformation of the lithosphere of the northwestern Okhotsk plate. We find that it is likely that the Okhotsk plate is cracked into slivers, but that rates of relative motion of these slivers are close to indistinguishable from the behaviour of a single, rigid plate. The analysis also suggests the upper bound for large earthquakes in the region to be Mw 7-7.5 which we expect to occur only on the plate boundary fault itself. This fits geological evidence for a long term offset rate 5-10 times higher on the major plate boundary fault than other lineaments cutting the Okhotsk plate itself.

Subducting plate geology in three great earthquake ruptures of the western Alaska margin, Kodiak to Unimak

Science.gov (United States)

von Huene, Roland E.; Miller, John J.; Weinrebe, Wilhelm

2012-01-01

Three destructive earthquakes along the Alaska subduction zone sourced transoceanic tsunamis during the past 70 years. Since it is reasoned that past rupture areas might again source tsunamis in the future, we studied potential asperities and barriers in the subduction zone by examining Quaternary Gulf of Alaska plate history, geophysical data, and morphology. We relate the aftershock areas to subducting lower plate relief and dissimilar materials in the seismogenic zone in the 1964 Kodiak and adjacent 1938 Semidi Islands earthquake segments. In the 1946 Unimak earthquake segment, the exposed lower plate seafloor lacks major relief that might organize great earthquake rupture. However, the upper plate contains a deep transverse-trending basin and basement ridges associated with the Eocene continental Alaska convergent margin transition to the Aleutian island arc. These upper plate features are sufficiently large to have affected rupture propagation. In addition, massive slope failure in the Unimak area may explain the local 42-m-high 1946 tsunami runup. Although Quaternary geologic and tectonic processes included accretion to form a frontal prism, the study of seismic images, samples, and continental slope physiography shows a previous history of tectonic erosion. Implied asperities and barriers in the seismogenic zone could organize future great earthquake rupture.

Alpine Serpentinite Geochemistry As Key To Define Timing Of Oceanic Lithosphere Accretion To The Subduction Plate Interface

Science.gov (United States)

Gilio, M.; Scambelluri, M.; Agostini, S.; Godard, M.; Pettke, D. T.; Angiboust, S.

2016-12-01

Isotopic (Pb, Sr and B) and trace element (B, Be, As, Sb, U, Th) signatures of serpentinites are useful geochemical tools to assess element exchange and fluid-rock interactions in subduction zone settings. They help to unravel geological history and tectonic evolution of subduction serpentinites and associated meta-oceanic crust. Sedimentary-derived fluid influx within HP plate interface environments strongly enriches serpentinites in As, Sb, B, U and Th and resets their B, Sr and Pb isotopic compositions. This HP metasomatic signature is preserved during exhumation and/or released at higher PT through de-serpentinization, fueling partial melting in the sub-arc mantle and recycling such fingerprint into arc magmas. This study focuses on the subduction recrystallization, geochemical diversity and fluid-rock interaction recorded by high- to ultra-high pressure (HP, UHP) Alpine serpentinites from the subducted oceanic plate (Cignana Unit, Zermatt-Saas Complex, Monviso and Lanzo Ultramafic Massifs). The As and Sb compositions of the HP-UHP Alpine ophiolitic rocks reveal the interaction between serpentinite and crust-derived fluids during their emplacement along the plate interface. This enables to define a hypothetical architecture of the Alpine subduction interface, considering large ultramafic slices. In this scenario, the Lanzo peridotite and serpentinite retain an As-Sb composition comparable to DM and PM: i.e. they experienced little exchange with sediment-derived fluids. Lanzo thus belonged to sections of the subducting plate, afar from the plate interface. Serpentinites from the Lago di Cignana Unit and Monviso and Voltri are richer in As and Sb, showing moderate to strong interaction with sediment- and crust-derived fluids during subduction (i.e. they behaved as open systems). These serpentinite slices accreted at the plate interface and exchanged with slab-derived fluids at different depths during Alpine subduction: Voltri accreted at shallower conditions (50

Phantom gastric mucosa for evaluating computed radiography in double-contrast upper gastrointestinal examinations

International Nuclear Information System (INIS)

Murakami, M.; Watanabe, H.; Nakata, H.

1996-01-01

To test the clinical usefulness of computed radiography (CR) with a storage phosphor plate in upper gastrointestinal radiographic examinations, a newly devised phantom gastric mucosa was used. Simulated small elevated and depressed lesions were created on a phantom gastric mucosa made from a styrofoam 'plate'. Twenty-four sets of each CR and screen-film radiographs (SR) were obtained using phototimed exposures. Receiver operating characteristic (ROC) study and visual ranking using these images were performed. There was no significant difference between the ROC curves of CR and SR. By visual ranking, CR was equal to or better than SR in most cases. In no case was SR definitely superior to CR. CR can be safely applied in upper gastrointestinal roentgenologic examinations. (orig.)

Concentration of 226Ra in rocks of the southern part of Lower Silesia (SW Poland)

International Nuclear Information System (INIS)

Przylibski, Tadeusz Andrzej

2004-01-01

The aim of the article is to present a preliminary description of rocks in the southern part of Lower Silesia and the Sudety Mountains in particular, with regard to 226 Ra content. The research demonstrates that the average content of this isotope was 40.4 Bq/kg in the rocks of the southern part of Lower Silesia, and 41.7 Bq/kg in the rocks of the Sudetes. These values are slightly higher than the mean 226 Ra content in the upper part of the Earth's crust, while the measured maximum content of this isotope (244 Bq/kg) is more than twice as high as the upper range of the values most frequently recorded in the upper part of the Earth's crust. The minimum values were lower than the detection limit, which was about 1 Bq/kg. These results reflect the mosaic-like geological structure of Lower Silesia, and particularly the Sudety Mountains, the occurrence of SiO 2 -rich igneous rocks and the products of their metamorphism, as well as numerous manifestations of uranium mineralisation or even deposital concentrations of this element. The rocks with the highest 226 Ra contents include (in decreasing order): aplites, granites, gneisses and leucogranites, granite-gneisses, granodiorites and rhyolites, and, finally, mudstones. The lowest values of 226 Ra content, on the other hand, were measured in sandstones, marls and conglomerates, and extremely low - in marbles and quartzites. The results show that background values of 226 Ra content in the rocks of the southern part of Lower Silesia fall within a range from several to about 100 Bq/kg, which is the same as the range most frequently recorded in the upper part of the Earth's crust. Distribution of these values has log-normal character. The research demonstrates that the southern part of Lower Silesia, and the Sudetes in particular, may be marked by an increased radon potential. Particularly liable areas are: the Karkonosze granite massif, especially in its border zones, the Ladek-Snieznik and the Izera massifs, especially in

Viewing device of a steam generator tube-plate

International Nuclear Information System (INIS)

Denis, J.; Poirier, D.

1984-01-01

The invention proposes a device to observe the tubular plate of a steam generator including rows of parallel tubes situated in a shell provided with at least one entrance situated face to the interval between two adjacent rows. The device comprises a boom of which transversal dimension is less important than the interval; the boom can be inserted by the entrance; it contains a rigid endoscope terminated in an eyepiece and an optical fibre lighguide in the same vertical plane for illumination of the far end. The respective rotary angled mirrors are driven simultaneously by drums connected to a rack-and-pinion mechanism which is operated by a plunger held by a spring against a rocking lever driven by a motor and cam. As the mirrors rotate, the illuminated zone overlaps the field of view of the endoscope. The tube plate area in the shadow of the endoscope mirror (20) is illuminated separately by an ailiary fibre with a fixed terminal mirror. The invention enables the observation of the tube plate on both sides of the boom. It can be used in the case of the inspection of the steam generator of a pressurized water reactor [fr

Frictional properties of relic fore arc metasediments from Kodiak Island, AK: Implications for slip in the upper accretionary prism

Science.gov (United States)

Miller, P.; Rabinowitz, H. S.; Saffer, D. M.; Savage, H. M.

2017-12-01

The slip behavior of subduction megathrusts is controlled by the mechanical and frictional properties of the material entrained along the plate interface. The shallow reaches of subduction thrusts (i.e. Events (SSE's), tremor, and very low frequency earthquakes (VLFE). However, there remain few detailed experimental studies of relevant fault materials under in situ conditions to probe the connections between rock frictional properties and fault slip behavior. To quantitatively understand the evolution of frictional properties along the upper part of the megathrust, we conducted a suite of shearing experiments at pressures and temperatures similar to in situ conditions, using exhumed subduction zone fault rocks composed of metamorphosed clay-rich sediments from Kodiak Island, Alaska. The metasediments we tested have experienced maximum burial depths ranging from 4-6 to 10-15 km, and peak temperatures ranging from 100-125 to 280 oC, making them ideal analogs for investigating the evolution of friction across the stability transition and into the seismogenic zone. These samples were powdered and sheared in a triaxial deformation apparatus at conditions ranging from 25 MPa and 20 oC, to 195 MPa and 200 oC. Preliminary results at room temperature show steady state friction values of 0.56 and rate strengthening behavior (a-b 0.002) with Dc of 19 mm. Ongoing work is characterizing the frictional properties across the stability transition in greater detail.

Safety assessment of U–Mo fuel mini plates irradiated in HANARO reactor

International Nuclear Information System (INIS)

Jo, Daeseong; Kim, Haksung

2015-01-01

Highlights: • Neutronic and thermal-hydraulic analyses of U–Mo fuel irradiated in HANARO reactor. • A mock-up irradiation target was designed and tested to measure the flow rate. • During normal operation, boiling does not occur. • During limiting accidents, boiling occurs. However, fuel integrity is maintained. - Abstract: Neutronic and thermal hydraulic characteristics of U–Mo fuel mini plates irradiated in the HANARO reactor were analyzed for the safety assessment of these plates. A total of eight fuel plates were double-stacked; each stack contained three 8.0 gU/cc U–7Mo fuel plates and one 6.5 gU/cc U–7Mo fuel plate. The neutronic and thermal hydraulic analyses were carried out using the MCNP code and TMAP code, respectively. The core status used in the study was the equilibrium core, and four Control Absorber Rod (CAR) locations were considered: 350 mm, 450 mm, 550 mm, and 650 mm away from the bottom of the core. For the fuels in the lower stack, the maximum heat flux was found at the CAR located at 450 mm. For the fuels in the upper stack, the maximum heat flux was found at the CAR located at 650 mm. The axial power distributions for the upper and lower stacks were selected on the basis of thermal margin analyses. A mock-up irradiation target assembly was designed and tested at the out-of-pile test facility to measure the flow rate through the irradiation site, given that the maximum flow rate through the irradiation site at the HANARO reactor is limited to 12.7 kg/s. For conservative analyses, measurement and correlation uncertainties and engineering hot channel factors were considered. During normal operation, the minimum ONB temperature margins for the lower and upper stacks are 41.6 °C and 31.8 °C, respectively. This means that boiling does not occur. However, boiling occurs during the limiting accidents. Nevertheless, the fuel integrity is maintained since the minimum DNBR are 1.96 for the Reactivity Insertion Accident (RIA) and 2

Wear plates control rod guide tubes top internal reactor vessel C. N. VANDELLOS II; Desgaste placas tubos guia barras de control interno superior vasija del reactor C.N. Vandellos II

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

The guide tubes for control rods forming part of the upper internals of the reactor vessel, its function is to guide the control rod to permit its insertion in the reactor core. These guide tubes are suspended from the upper support plate which are fixed by bolts and extending to the upper core plate which is fastened by clamping bolts (split pin) to prevent lateral displacement of the guide tubes, while allowing axial expansion.

Transformation of Serpentinite to Listvenite as Recorded in the Vein History of Rocks From Oman Drilling Project Hole BT1B

Science.gov (United States)

Manning, C. E.; Kelemen, P. B.; Michibayashi, K.; Harris, M.; Urai, J. L.; de Obeso, J. C.; Jesus, A. P. M.; Zeko, D.

2017-12-01

Oman Drilling Project Hole BT1B intersected 191 m of listvenite (magnesite + quartz rock) and serpentinite in the hanging wall of the basal thrust of the Oman ophiolite. Recovery was 100%. Listvenite is the dominant lithology in the upper plate rocks (166 m). Its shows wide color and textural variation, including pseudomorphic replacement of serpentinized peridotite. Serpentinite was encountered in two main contiguous intervals totaling 25 m. In light of the strongly metasomatic nature for the origin of listvenite, a substantial portion of the core description effort was dedicated to characterization of the complex veining history recorded in the hole. Dense veining is recorded in both lithologies. The density of 200/m. The density of veins >1 mm was 50-100/m, with somewhat higher densities recorded in serpentinite than in listvenite. In order of oldest to youngest, the main vein types in serpentinite are microscopic mesh-textured serpentine veins, macroscopic serpentine veins, carbonate-oxide veins, and carbonate veins. The vein paragenesis in listvenite is: early carbonate-oxide veins, followed by carbonate and carbonate-quartz veins, then late carbonate veins. The carbonate-oxide and carbonate veins are shared by the lithologies and hold clues to the transformation of ultramafic rocks to listvenite. Carbonate-oxide veins form a distinctive set that is interpreted to be the earliest record of carbonate formation in serpentinite. They contain Fe-oxide, usually hematite, on a medial line, with antitaxial magnesite crystals growing outward and showing terminations against wall rock minerals. Antitaxial textures may be evidence of positive reaction volumes. In serpentinite, secondary serpentine after earlier serpentine is common at vein margins. Carbonate-oxide veins are the earliest observed in listvenite, where they may form isolated veins to dense, aligned networks that impart a foliated texture. In some cases, they appear to predate replacement of serpentine by

Connection between end plates and rods in a BWR fuel element

International Nuclear Information System (INIS)

Cali', G.P.

1975-01-01

The problem of the connection between the end plates and the rods of a BWR fuel element is analytically formulated. The behaviour of the springs coupling the rods with the upper plate is analyzed with particular detail since the deformation of these springs affects the forces at the interface of the fuel element structure components. A tool is given to design the springs according to some considerations regarding the mechanical strength of the interacting components as well as the influence of the possible geometrical unevennes of the system that can arise during the fuel element lifetime. (Cali', G.P.)

Modeling particulate removal in plate-plate and wire-plate electrostatic precipitators

Directory of Open Access Journals (Sweden)

S Ramechecandane

2016-09-01

Full Text Available The present study is concerned with the modeling of electrically charged particles in a model plate-plate and a single wire-plate electrostatic precipitator (ESP. The particle concentration distributions for both a plate-plate and a wire-plate ESP are calculated using a modified drift flux model. Numerical investigations are performed using the modified drift flux model for particle number concentration, in addition to the RNG k - ε model for the mean turbulent flow field and the Poisson equation for the electric field. The proposed model and the outlined methodology for coupling the flow field, electric field, charging kinetics and particle concentration is applied to two model precipitators that are truly representative of a wide class of commercialized ESPs. The present investigation is quite different from the earlier studies as it does not make assumptions like a homogeneous electric field or an infinite turbulent diffusivity. The electric field calculated is a strong function of position and controls the migration velocity of particles. Hence, the proposed model can be implemented in a flow solver to obtain a full-fledged solution for any kind of ESP with no limitations on the particle number concentration, as encountered in a Lagrangian approach. The effect of turbulent diffusivity on particle number concentration in a plate-plate ESP is investigated in detail and the results obtained are compared with available experimental data. Similarly, the effect of particle size/diameter and applied electric potential on the accumulative collection performance in the case of a wire-plate ESP is studied and the results obtained are compared with available numerical data. The numerical results obtained using the modified drift flux model for both the plate-plate and wire-plate ESP are in close agreement with available experimental and numerical data.

Karst connections between unconfined aquifers and the Upper Floridan aquifer in south Georgia: geophysical evidence and hydrogeological models

Science.gov (United States)

Thieme, D. M.; Denizman, C.

2011-12-01

Buried karst features in sedimentary rocks of the south Georgia Coastal Plain present a challenge for hydrogeological models of recharge and confined flow within the underlying Upper Floridan aquifer. The Withlacoochee River, the trunk stream for the area, frequently disappears into subsurface caverns as it makes its way south to join the Suwannee River in northern Florida. The Withlacoochee also receives inputs from small ponds and bays which in turn receive spring and seep groundwater inputs. We have mapped karst topography at the "top of rock" using ground-penetrating radar (GPR). Up to seven meters of relief is indicated for the paleotopography on Miocene to Pliocene rocks, contrasting with the more subdued relief of the modern landscape. Current stratigraphic and hydrogeological reconstructions do not incorporate this amount of relief or lateral variation in the confining beds. One "pipe" which is approximately four meters in diameter is being mapped in detail. We have field evidence at this location for rapid movement of surficial pond and river water with a meteoric signature through several separate strata of sedimentary rock into an aquifer in the Hawthorn formation. We use our geophysical and hydrological field evidence to constrain quantitative hydrogeological models for the flow rates into and out of both this upper aquifer and the underlying Upper Floridan aquifer, which is generally considered to be confined by the clays of the Hawthorn.

Rheological and structural inheritance : key parameters for intra-plate deformation. A study based on analogue models

NARCIS (Netherlands)

Calignano, E.

2015-01-01

Mountain ranges are impressive tectonic features that characterize the Earth’s surface. Their formation is often associated with regions where two tectonic plates, making up the Earth surface, collide, as in the case of the Himalaya. While the surface is forced to uplift, the displacement of rocks

Water - rock interaction in different rock environments

International Nuclear Information System (INIS)

Lamminen, S.

1995-01-01

The study assesses the groundwater geochemistry and geological environment of 44 study sites for radioactive waste disposal. Initially, the study sites were divided by rock type into 5 groups: (1) acid - intermediate rocks, (2) mafic - ultramafic rocks, (3) gabbros, amphibolites and gneisses that contain calc-silicate (skarn) rocks, (4) carbonates and (5) sandstones. Separate assessments are made of acid - intermediate plutonic rocks and of a subgroup that comprises migmatites, granite and mica gneiss. These all belong to the group of acid - intermediate rocks. Within the mafic -ultramafic rock group, a subgroup that comprises mafic - ultramafic plutonic rocks, serpentinites, mafic - ultramafic volcanic rocks and volcanic - sedimentary schists is also evaluated separately. Bedrock groundwaters are classified by their concentration of total dissolved solids as fresh, brackish, saline, strongly saline and brine-class groundwaters. (75 refs., 24 figs., 3 tabs.)

Sedimentological characteristics and depositional environment of Upper Gondwana rocks in the Chintalapudi sub-basin of the Godavari valley, Andhra Pradesh, India

Science.gov (United States)

Ramamohanarao, T.; Sairam, K.; Venkateswararao, Y.; Nagamalleswararao, B.; Viswanath, K.

2003-03-01

The Kota (Early to Middle Jurassic) and Gangapur (Early Cretaceous) rocks of the Chintalapudi sub-basin of Gondwana are poorly to very poorly sorted, positively to very positively skewed, and leptokurtic to very leptokurtic. The Kota rocks show a single prominent truncation line at the inflection of saltation/suspension at 2.0 φ of the river mode of transportation. The Gangapur rocks show two truncation lines of saltation/suspension, one at 0.5-1.7 φ and the other at 2.4-4.0 φ. These are inferred to be due to a high turbulent phase of the river. On the multigroup multivariant discriminant functions V1- V2 diagram, the bulk of the samples from Kota and Gangapur fall in the field of turbidite deposition. This study supports the view that the discrimination of river from turbidite deposits on this diagram is poor since both deposits are identical in terms of settling velocity distribution. On the C- M diagram, the Kota and Gangapur rocks show segments of rolling, bottom suspension, and graded suspension during river transport of sediment. The Q-R segments of graded suspension for these rocks have a C/ M ratio of 2.5, which is close to the ratio of the turbidites. The Kota and Gangapur rocks have nearly the same assemblage of heavy minerals. The provenance is inferred to consist of basic igneous rocks, acid igneous rocks, high-grade metamorphic rocks and sedimentary rocks.

Relating rock avalanche morphology to emplacement processes

Science.gov (United States)

Dufresne, Anja; Prager, Christoph; Bösmeier, Annette

2015-04-01

/limestone sequences to weaker siliciclastic and evaporitic beds (sand-/siltstones, rauhwacken) can be pinpointed on LiDAR shaded relief images of the rock avalanche deposit. Hence, several morphological signatures are clearly related to differences in mechanical behaviour of the involved lithologies, whereas others reflect particular emplacement modes of the same rock unit: e.g. rockslide motion versus rock avalanche spreading. Reference Patzelt G. 2012. The rock avalanches of Tschirgant and Haiming (Upper Inn Valley, Tyrol, Austria), comment on the map supply. (German language only). Jahrbuch der Geologischen Bundesanstalt 152(1-4): 13-24.

Research on petrologic, geochemical characteristics and genesis of volcanic rocks in Dachangsha basin

International Nuclear Information System (INIS)

Wei Sanyuan

1999-01-01

On the basis of research on petrologic, geochemical characteristics and isotope composition of volcanic rocks in Dachangsha basin, the author concludes that the volcanic rocks formed from magma of different genesis and depth are double-cycle effusive. It is proposed that the magma forming the intermediate-basic volcanics of the first cycle comes from the mixing of the partial melting of the deep crust and mantle, and the intermediate-acidic volcanics of the secondary cycle are derived from the remelting of the upper crust

Ways of distinguishing epigenetic types of gray-colored rocks in sheet-infiltration deposits

International Nuclear Information System (INIS)

Rasulova, S.D.; Yashunskii, Yu.V.

1994-01-01

At an infiltration deposit of uranium in Upper-Cretaceous sandy-clay alluvial deposits (Central Kyzylkum), six stages of postsedimentation epigenetic transformations were distinguished. The genesis of altered rocks was determined mostly by mineralogical methods. A new methodological technique is suggested, which calls for analysis of the textural, structural, and mineral correspondence of ferruginous components of gray-colored and oxidized rocks in the region of their contact and makes it possible to typify epigenetic changes in conditions of repeated change in the direction of geochemical processes

Complex Contact Angles Calculated from Capillary Rise Measurements on Rock Fracture Faces

Science.gov (United States)

Perfect, E.; Gates, C. H.; Brabazon, J. W.; Santodonato, L. J.; Dhiman, I.; Bilheux, H.; Bilheux, J. C.; Lokitz, B. S.

2017-12-01

Contact angles for fluids in unconventional reservoir rocks are needed for modeling hydraulic fracturing leakoff and subsequent oil and gas extraction. Contact angle measurements for wetting fluids on rocks are normally performed using polished flat surfaces. However, such prepared surfaces are not representative of natural rock fracture faces, which have been shown to be rough over multiple scales. We applied a variant of the Wilhelmy plate method for determining contact angle from the height of capillary rise on a vertical surface to the wetting of rock fracture faces by water in the presence of air. Cylindrical core samples (5.05 cm long x 2.54 cm diameter) of Mancos shale and 6 other rock types were investigated. Mode I fractures were created within the cores using the Brazilian method. Each fractured core was then separated into halves exposing the fracture faces. One fracture face from each rock type was oriented parallel to a collimated neutron beam in the CG-1D imaging instrument at ORNL's High Flux Isotope Reactor. Neutron radiography was performed using the multi-channel plate detector with a spatial resolution of 50 μm. Images were acquired every 60 s after a water reservoir contacted the base of the fracture face. The images were normalized to the initial dry condition so that the upward movement of water on the fracture face was clearly visible. The height of wetting at equilibrium was measured on the normalized images using ImageJ. Contact angles were also measured on polished flat surfaces using the conventional sessile drop method. Equilibrium capillary rise on the exposed fracture faces was up to 8.5 times greater than that predicted for polished flat surfaces from the sessile drop measurements. These results indicate that rock fracture faces are hyperhydrophilic (i.e., the height of capillary rise is greater than that predicted for a contact angle of zero degrees). The use of complex numbers permitted calculation of imaginary contact angles for

Temporal variations of Sr isotopic compositions for the rocks from Dogo, Oki islands Shimane Prefecture

International Nuclear Information System (INIS)

Fujimaki, Hirokazu; Xu Hong; Aoki, Ken-ichiro

1991-01-01

Fifty-three volcanic rocks from Dogo island, Oki, Shimane Prefecture, southwestern Japan were analyzed for Sr isotopic compositions with two basement rocks. The rock samples consist of calc-alkali rock suite, Nagaoda shoshonite-banakite suite, Oki trachyte-rhyolite suite, Dogo mugearite suite, Hei trachyte and Tsuzurao rhyolite series, and Daimanjiyama, Ohmine, Kuroshima, Shiroshimazaki, Saigo, and Misaki alkali basalt groups in the order of probable eruption sequence. The volcanic rocks of calc-alkali suite and shoshonite-banakite suite were produced before Japan Sea opening (ca. 15 Ma), and both have 87 Sr/ 86 Sr ratios higher than 0.7068. Long after Japan Sea opening Oki-trachyte-rhyolite suite was erupted (ca. 6.6 Ma); they have rather low 87 Sr/ 86 Sr ratios (0.7066-0.7081). Mugearites followed and have similar Sr isotopic composition, whereas 4.6 Ma old Daimanjiyama basalts have clearly low 87 Sr/ 86 Sr ratios (0.7050-0.7051). The rocks erupted 3-4 Ma seem to have the lowest 87 Sr/ 86 Sr ratios; they are Ohmine, Kuroshima, Shiroshimazaki alkali basalt suites (0.7044-0.7048). The 87 Sr/ 86 Sr ratios of the Saigo basalts erupted 0.84 Ma are higher than those erupted 3-4 Ma. The latest volcanic products in Dogo island, Misaki basalt suite has even higher 87 Sr/ 86 Sr ratios (0.7054-0.7057) than the Saigo basalt suite. Thus, temporal and systematic variation of Sr isotopic compositions of the volcanic rocks from Dogo can be recognized. The 87 Sr/ 86 Sr ratios of the rocks were once as high as 0.7066 or even higher than 0.708, but they started decreasing down to ca. 0.7044-0.7048 4-3 Ma ago. Since then the ratios rebounded to 0.7049-0.7055. The Hei trachyte and Tsuzurao rhyolite series are not included in this temporal and systematic change. The mantle diapir associated with Japan Sea spreading might have caused the decrease in the ratios, and either Pacific Ocean plate or Philippine Sea plate subduction may be responsible for this rebound. (author)

A novel polarization interferometer for measuring upper atmospheric winds

International Nuclear Information System (INIS)

Ting-Kui, Mu; Chun-Min, Zhang

2010-01-01

A static polarization interferometer for measuring upper atmospheric winds is presented, based on two Savart plates with their optical axes perpendicular to each other. The principle and characteristics of the interferometer are described. The interferometer with a wide field of view can offer a stable benchmark optical path difference over a specified spectral region of 0.55–0.63 μm because there are no quarter wave plates. Since the instrument employs a straight line common-path configuration but without moving parts and slits, it is very compact, simple, inherently robust and has high throughput. The paper is limited to a theoretical analysis. (general)

Alteration of submarine volcanic rocks in oxygenated Archean oceans

Science.gov (United States)

Ohmoto, H.; Bevacqua, D.; Watanabe, Y.

2009-12-01

Most submarine volcanic rocks, including basalts in diverging plate boundaries and andesites/dacites in converging plate boundaries, have been altered by low-temperature seawater and/or hydrothermal fluids (up to ~400°C) under deep oceans; the hydrothermal fluids evolved from shallow/deep circulations of seawater through the underlying hot igneous rocks. Volcanogenic massive sulfide deposits (VMSDs) and banded iron formations (BIFs) were formed by mixing of submarine hydrothermal fluids with local seawater. Therefore, the behaviors of various elements, especially of redox-sensitive elements, in altered submarine volcanic rocks, VMSDs and BIFs can be used to decipher the chemical evolution of the oceans and atmosphere. We have investigated the mineralogy and geochemistry of >500 samples of basalts from a 260m-long drill core section of Hole #1 of the Archean Biosphere Drilling Project (ABDP #1) in the Pilbara Craton, Western Australia. The core section is comprised of ~160 m thick Marble Bar Chert/Jasper Unit (3.46 Ga) and underlying, inter-bedded, and overlying submarine basalts. Losses/gains of 65 elements were quantitatively evaluated on the basis of their concentration ratios against the least mobile elements (Ti, Zr and Nb). We have recognized that mineralogical and geochemical characteristics of many of these samples are essentially the same as those of hydrothermally-altered modern submarine basalts and also those of altered volcanic rocks that underlie Phanerozoic VMSDs. The similarities include, but are not restricted to: (1) the alteration mineralogy (chlorite ± sericite ± pyrophyllite ± carbonates ± hematite ± pyrite ± rutile); (2) the characteristics of whole-rock δ18O and δ34S values; (3) the ranges of depletion and enrichment of Si, Al, Mg, Ca, K, Na, Fe, Mn, and P; (4) the enrichment of Ba (as sulfate); (5) the increases in Fe3+/Fe2+ ratios; (6) the enrichment of U; (7) the depletion of Cr; and (8) the negative Ce anomalies. Literature data

Arsenic, Chromium, and Other Potentially Toxic Elements in the Rocks and Sediments of Oropos-Kalamos Basin, Attica, Greece

Directory of Open Access Journals (Sweden)

D. Alexakis

2014-01-01

Full Text Available Rocks and sediments are non-anthropogenic sources of elements contamination. In this study, a series of potentially toxic elements were quantified in rocks and sediments of the Oropos-Kalamos basin. Only As, Hg, Pb, and Sb contents, in all the examined rocks and sediments, were higher than the levels given in international literature. Concentration of the elements As, Cr, Hg, Mo, Ni, and U is highly elevated in the lignite compared to crustal element averages. The enrichment of Cr and Ni in the lignite can be attributed to the known ultramafic rock masses surrounding the basin, while enrichment of As, Hg, Mo, Sb, and U is associated with the past geothermal activity of the Upper Miocene (about 15 million years ago. Nickel and Cr were transported into the lignite deposition basin by rivers and streams draining ultramafic rock bodies. The results of this study imply the natural source of Cr3+ and Cr6+ contamination of the Oropos-Kalamos groundwater, since high Cr contents were also recorded in the lignite (212.3 mg kg−1, chromiferous iron ore occurrences (256.6 mg kg−1, and alluvial deposits (212.5 mg kg−1, indicating Cr leaching and transportation to the depositional basin dating from the Upper Miocene age.

Development of soda-lime glasses from ornamental rock wastes

International Nuclear Information System (INIS)

Babisk, Michelle Pereira

2009-01-01

During the ornamental rocks production, among other steps, one saw the rock blocks in order to transform them into semi-finished plates. In this step, expressive amounts of residues are generated, which are not properly discharged in nature, without any programmed utilization. The residues of silicide rocks present, in their compositions, oxides which are raw materials employed to fabricate soda-lime type glasses (containing SiO_2, Al_2O_3, CaO, Na_2O and K_2O). On the other hand the residues of carbonatic rocks are constituted of glass net modifier oxides, like CaO and MgO. In this work it was developed four types of soda-lime glasses using ornamental rock residues, where the glasses compositions were adjusted by adding sand, as silica source, as well as sodium and calcium carbonates as sources of Na_2O and CaO, respectively. The obtained glasses were characterized by means of Archimed's method for densities measurements, microstructure by using optical and electronic microscopy, phases by means of X-ray diffraction (XRD), hardness by Vickers indentation, spectroscopy (UV/VIS), and hydrolytic resistance according to ISO 719. The XRD analyses confirmed the compositions total vitrification, where the greened aspect of the samples was due to the presence of the iron oxides. The produced glasses properties were compared with those of commercial glasses aiming their industrial employment. The main difference between the produced glasses and those commercials varied primarily regarding the amount of carbonates incorporated. The results showed that the ornamental rocks residues may be used as raw materials for glasses fabrication, and they found a useful economic destination rather than discharge which promotes undesirable environmental impact. (author)

Basis for paleoenvironmental interpretation of magnetic properties of sediment from Upper Klamath Lake (Oregon): Effects of weathering and mineralogical sorting

Science.gov (United States)

Rosenbaum, J.G.; Reynolds, R.L.

2004-01-01

Studies of magnetic properties enable reconstruction of environmental conditions that affected magnetic minerals incorporated in sediments from Upper Klamath Lake. Analyses of stream sediment samples from throughout the catchment of Upper Klamath Lake show that alteration of Fe-oxide minerals during subaerial chemical weathering of basic volcanic rocks has significantly changed magnetic properties of surficial deposits. Titanomagnetite, which is abundant both as phenocrysts and as microcrystals in fresh volcanic rocks, is progressively destroyed during weathering. Because fine-grained magnetite is readily altered due to large surface-to-volume ratios, weathering causes an increase in average magnetic grain size as well as reduction in the quantity of titanomagnetite both absolutely and relative to hematite. Hydrodynamic mineralogical sorting also produces differences in magnetic properties among rock and mineral grains of differing sizes. Importantly, removal of coarse silicate and Fe-oxide grains by sorting concentrated extremely fine-grained magnetite in the resulting sediment. The effects of weathering and sorting of minerals cannot be completely separated. These processes combine to produce the magnetic properties of a non-glacial lithic component of Upper Klamath Lake sediments, which is characterized by relatively low magnetite content and coarse magnetic grain size. Hydrodynamic sorting alone causes significant differences between the magnetic properties of glacial flour in lake sediments and of fresh volcanic rocks in the catchment. In comparison to source volcanic rocks, glacial flour in the lake sediment is highly enriched in extremely fine-grained magnetite.

Importance of Upper-Limb Inertia in Calculating Concentric Bench Press Force

OpenAIRE

RAMBAUD, O; RAHMANI, A; MOYEN, B; BOURDIN, M

2008-01-01

The purpose of this study was to investigate the influence of upper-limb inertia on the force-velocity relationship and maximal power during concentric bench press exercise. Reference peak force values (Fpeakp) measured with a force plate positioned below the bench were compared to those measured simultaneously with a kinematic device fixed on the barbell by taking (Fpeakt) or not taking (Fpeakb) upper-limb inertia into account. Thirteen men (27.8 6 4.1 years, 184.6 6 5.5 cm, 99.5 6 18.6 kg) ...

Paleoclimate cycles and tectonic controls on fluvial, lacustrine, and eolian strata in upper Triassic Chinle Formation, San Juan basin

Energy Technology Data Exchange (ETDEWEB)

Dubiel, R.F. (Geological Survey, Denver, CO (USA))

1989-09-01

Sedimentologic study of the Upper Triassic Chinle Formation in the San Juan basin (SJB) indicates that Late Triassic paleoclimate and tectonic movements influenced the distribution of continental lithofacies. The Shinarump, Monitor Butte, and Petrified Forest Members in the lower part of the Chinle consist of complexly interfingered fluvial, floodplain, marsh, and lacustrine rocks; the Owl Rock and Rock Point Members in the upper part consists of lacustrine-basin and eolian sandsheet strata. Facies analysis, vertebrate and invertebrate paleontology, and paleoclimate models demonstrate that the Late Triassic was dominated by tropical monsoonal circulation, which provided abundant precipitation interspersed with seasonally dry periods. Owl Rock lacustrine strata comprise laminated limestones that reflect seasonal monsoonal precipitation and larger scale, interbedded carbonates and fine-grained clastics that represent longer term, alternating wet and dry climatic cycles. Overlying Rock Point eolian sand-sheet and dune deposits indicate persistent alternating but drier climatic cyclicity. Within the Chinle, upward succession of lacustrine, alternating lacustrine/eolian sand-sheet, and eolian sand-sheet/dune deposits reflects an overall decrease in precipitation due to the northward migration of Pangaea out of low latitudes dominated by monsoonal circulation.

Selected elements of rock burst state assessment in case studies from the Silesian hard coal mines

Energy Technology Data Exchange (ETDEWEB)

Jozef Kabiesz; Janusz Makowka [Central Mining Institute, Katowice (Poland)

2009-09-15

Exploitation of coal seams in the Upper Silesian Coal Basin is conducted in complex and difficult conditions. These difficulties are connected with the occurrence of many natural mining hazards and limitations resulting from the existing in this area surface infrastructure. One of the most important problems of Polish mining is the rock burst hazard and reliable evaluation of its condition. During long-years' mining practice in Poland a comprehensive system of evaluation and control of this hazard was developed. In the paper the main aspects of rock burst hazard state evaluation will be presented, comprising: 1) rock mass inclination for rock bursts, i.e., rock strength properties investigation, comprehensive parametric evaluation of rock mass inclination for rock bursts, prognosis of seismic events induced by mining operations, methods of computer-aided modelling of stress and rock mass deformation parameters distribution, strategic rock mass classification under rock burst degrees; 2) immediate seismic and rock burst hazard state evaluation, i.e., low diameter test drilling method, seismologic and seismoacoustic method, comprehensive method of rock burst hazard state evaluation, non-standard methods of evaluation; 3) legal aspects of rock burst hazard state evaluation. Selected elements of the hazard state evaluation system are illustrated with specific practical examples of their application. 11 refs., 14 figs.

The Continental Margin of East Asia: a collage of multiple plates formed by convergence and extension from multiple directions

Science.gov (United States)

Mao, J.; Wang, T.; Ludington, S.; Qiu, Z.; Li, Z.

2017-12-01

East Asia is one of the most complex regions in the world. Its margin was divided into 4 parts: Northeast Asia, North China, South China and Southeast Asia. During the Phanerozoic, continental plates of East Asia have interacted successively with a) the Paleo Tethyan Ocean, b) the Tethyan and Paleo Pacific Oceans and c) the Pacific and Indian. In the Early Mesozoic, the Indosinian orogeny is characterized by the convergence and extension within multiple continental plates, whereas the Late Mesozoic Yanshanian orogeny is characterized by both convergence and compression due to oceanic subduction and by widespread extension. We propose this combination as "East Asia Continental Margin type." Except in Northeast Asia, where Jurassic and Cretaeous accretionary complexes are common, most magmatic rocks are the result of reworking of ancient margins of small continental plates; and oceanic island arc basalts and continental margin arc andesites are largely absent. Because South China is adjacent to the western margin of the Pacific Plate, some effects of its westward subduction must be unavoidable, but juvenile arc-related crust has not been identified. The East Asian Continental Margin is characterized by magmatic rocks that are the result of post-convergent tectonics, which differs markedly from the active continental margins of both South and North America. In summary, the chief characteristics of the East Asian Continental Margin are: 1) In Mesozoic, the periphery of multiple blocks experienced magmatism caused by lithospheric delamination and thinning in response to extension punctuated by shorter periods of convergence. 2) The main mechanism of magma generation was the partial melting of crustal rocks, due to underplating by upwelling mafic magma associated with the collapse of orogenic belts and both extension and compression between small continental blocks. 3) During orogeny, mostly high Sr/Y arc-related granitoids formed, whereas during post-orogenic times, A

Spirit Beside 'Home Plate,' Sol 1809 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11803 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11803 NASA Mars Exploration Rover Spirit used its navigation camera to take the images assembled into this stereo, 120-degree view southward after a short drive during the 1,809th Martian day, or sol, of Spirit's mission on the surface of Mars (February 3, 2009). By combining images from the left-eye and right-eye sides of the navigation camera, the view appears three-dimensional when viewed through red-blue glasses with the red lens on the left. Spirit had driven about 2.6 meters (8.5 feet) that sol, continuing a clockwise route around a low plateau called 'Home Plate.' In this image, the rocks visible above the rovers' solar panels are on the slope at the northern edge of Home Plate. This view is presented as a cylindrical-perspective projection with geometric seam correction.

The Upper Danube Nature Park

International Nuclear Information System (INIS)

Dosedla, H.C.

1997-01-01

When in 1980 the Upper Danube Nature Park was founded as one of 65 nature sanctuaries in Germany there was great diversity of opinions concerning its intended character. The protected region consisting of a geologically outstanding landscape within central Europe is covering the first 80 km the upper Danube where the young river shortly after it's source in the Black Forest is breaking through the narrow canyons of the Jurassic rock plateau of the so-called Suebian Alps and also locates the subterranean passage where the stream is submerging from the surface for nearly ten miles. Since the purpose of nature preservation according to German las is closely combined with the rather contradicting aim of offering an attractive recreation area thus facing the immense impacts of modern mass tourism there are numerous problems which in the course of years have resulted in an intricate patterns of subtle management methods coping with the growing awareness of the ecological balance. (author)

Regional stratigraphy, sedimentology, and tectonic significance of Oligocene-Miocene sedimentary and volcanic rocks, northern Baja California, Mexico

Science.gov (United States)

Dorsey, Rebecca J.; Burns, Beverly

1994-01-01

Upper Oligocene (?) to middle Miocene sedimentary and volcanic rocks in northern Baja California were deposited along the western margin of North America during subduction of the Guadalupe plate and southward migration of the Rivera Triple Junction. Regional mapping and compilation of stratigraphic data reveal a sequence of three regionally traceable stratigraphic units. (1) Oligocene (?) to lower Miocene Mesa Formation: basal quartz-rich fluvial sandstone, grus, conglomerate, and accessory facies, whose detrital compositions reflect the composition of local pre-Tertiary basement rock. (2) Lower to middle Miocene Comondú Formation: laterally variable sequence of volcaniclastic conglomerate, breccia, sandstone, tuff and minor volcanic flow units. (3) Widespread mesa-capping rhyolite tuff, typically welded and crystal-rich, probably upper Miocene in age. The Mesa Formation overlies a highly irregular and deeply dissected erosional surface developed on pre-Tertiary basement rock. The shift from pre-Mesa erosion to widespread (though localized) deposition and valley-filling records the final phase of late Cretaceous to middle Tertiary regional subsidence and eastward transgression that resulted from slow cooling and thermal contraction of Cretaceous arc crust during a temporal gap in magmatic activity along the western Cordilleran margin. Nonmarine sediments of the Mesa Formation were deposited in small, steep-walled paleovalleys and basins that gradually filled and evolved to form through-going, low-energy ephemeral stream systems. The gradational upward transition from the Mesa to Comondú Formation records the early to middle Miocene onset of subduction-related arc magmatism in eastern Baja California and related westward progradation of alluvial volcaniclastic aprons shed from high-standing eruptive volcanic centers. Pre-existing streams were choked with the new influx of volcanic detritus, causing the onset of rapid sediment deposition by stream flows and dilute

Pb, Sr and Nd isotope geological characteristics and its evolution of Jianchaling rock

International Nuclear Information System (INIS)

Pang Chunyong; Chen Minyang; Xu Wenxin

2003-01-01

It has been a long time debatable subject on the raw material source and its genesis of Jianchaling ultrabasic rock, because the original rock phases, the original mineral compositions, texture and structure, even part of the chemical components of the rocks had been changed completely after many periods and phases of metamorphism. According to the content of Pb, Rb, Sr, Nd elements and their Pb, Sr, Nd isotope compositions of the rocks, together with the isotope geological age of late magmatic activities, the authors analyze the evolution of Pb, Sr, Nd isotope compositions, The inferred initiate Nd isotope ratio of ultrabasic rocks is 0.510233, lower than that of meteorite unity at a corresponding period, its ε Nd(T)>O; The initiate Sr ratios inferred by the isotope geological age ranges from 0.702735 to 0.719028; Projecting the lead isotope compositions on the Pb tectonic evolution model, the result indicates that the raw material of Jianchaling ultrabasic rock coming from the deplete upper mantle. The ultrabasic magma which enrich of Mg, Ni and less S intruded the crust and formed the Jianchaling ultrabasic rock at late Proterozoic era (927 Ma±). The forming time of serpentinite is mostly equal to the granitoid intruding time, showing the intrusion o flate acidic magma caused a large scale alteration of the ultrabasic rocks and formed the meta-ultrabasic phase rock observed today. (authors)

Evolution of and Factors Controlling Eocene Sedimentation in the Darende-Balaban Basin, Malatya (Eastern Turkey)

OpenAIRE

GÜL, KEMAL GÜRBÜZ & MURAT

2005-01-01

Collision of the Arabian and Anatolian plates affected evolution of basins located along the southern flank of the Anatolian Plate. The Darende-Balaban foreland basin is one such basin – a basin filled with Upper Cretaceous and Eocene sediments, accumulated unconformably and transgressively above ophiolitic and carbonate basement rocks. This basin is locally surrounded, to the north and south, by Late Jurassic–Early Cretaceous structural highs created by tectonic elements during the collision...

Evolution of and Factors Controlling Eocene Sedimentation in the Darende-Balaban Basin, Malatya (Eastern Turkey)

OpenAIRE

GÜL, KEMAL GÜRBÜZ & GÜL, MURAT

2014-01-01

Collision of the Arabian and Anatolian plates affected evolution of basins located along the southern flank of the Anatolian Plate. The Darende-Balaban foreland basin is one such basin – a basin filled with Upper Cretaceous and Eocene sediments, accumulated unconformably and transgressively above ophiolitic and carbonate basement rocks. This basin is locally surrounded, to the north and south, by Late Jurassic–Early Cretaceous structural highs created by tectonic elements during the collision...

Vertebrate paleontological exploration of the Upper Cretaceous succession in the Dakhla and Kharga Oases, Western Desert, Egypt

Science.gov (United States)

Sallam, Hesham M.; O'Connor, Patrick M.; Kora, Mahmoud; Sertich, Joseph J. W.; Seiffert, Erik R.; Faris, Mahmoud; Ouda, Khaled; El-Dawoudi, Iman; Saber, Sara; El-Sayed, Sanaa

2016-05-01

The Campanian and Maastrichtian stages are very poorly documented time intervals in Africa's record of terrestrial vertebrate evolution. Upper Cretaceous deposits exposed in southern Egypt, near the Dakhla and Kharga Oases in the Western Desert, preserve abundant vertebrate fossils in nearshore marine environments, but have not yet been the focus of intensive collection and description. Our recent paleontological work in these areas has resulted in the discovery of numerous new vertebrate fossil-bearing localities within the middle Campanian Qusier Formation and the upper Campanian-lower Maastrichtian Duwi Formation. Fossil remains recovered from the Campanian-aged Quseir Formation include sharks, rays, actinopterygian and sarcopterygian fishes, turtles, and rare terrestrial archosaurians, including some of the only dinosaurs known from this interval on continental Africa. The upper Campanian/lower Maastrichtian Duwi Formation preserves sharks, sawfish, actinopterygians, and marine reptiles (mosasaurs and plesiosaurs). Notably absent from these collections are representatives of Mammalia and Avialae, both of which remain effectively undocumented in the Upper Cretaceous rocks of Africa and Arabia. New age constraints on the examined rock units is provided by 23 nannofossil taxa, some of which are reported from the Duwi Formation for the first time. Fossil discoveries from rock units of this age are essential for characterizing the degree of endemism that may have developed as the continent became increasingly tectonically isolated from the rest of Gondwana, not to mention for fully evaluating origin and diversification hypotheses of major modern groups of vertebrates (e.g., crown birds, placental mammals).

Reactive solute transport in an asymmetrical fracture-rock matrix system

Science.gov (United States)

Zhou, Renjie; Zhan, Hongbin

2018-02-01

The understanding of reactive solute transport in a single fracture-rock matrix system is the foundation of studying transport behavior in the complex fractured porous media. When transport properties are asymmetrically distributed in the adjacent rock matrixes, reactive solute transport has to be considered as a coupled three-domain problem, which is more complex than the symmetric case with identical transport properties in the adjacent rock matrixes. This study deals with the transport problem in a single fracture-rock matrix system with asymmetrical distribution of transport properties in the rock matrixes. Mathematical models are developed for such a problem under the first-type and the third-type boundary conditions to analyze the spatio-temporal concentration and mass distribution in the fracture and rock matrix with the help of Laplace transform technique and de Hoog numerical inverse Laplace algorithm. The newly acquired solutions are then tested extensively against previous analytical and numerical solutions and are proven to be robust and accurate. Furthermore, a water flushing phase is imposed on the left boundary of system after a certain time. The diffusive mass exchange along the fracture/rock matrixes interfaces and the relative masses stored in each of three domains (fracture, upper rock matrix, and lower rock matrix) after the water flushing provide great insights of transport with asymmetric distribution of transport properties. This study has the following findings: 1) Asymmetric distribution of transport properties imposes greater controls on solute transport in the rock matrixes. However, transport in the fracture is mildly influenced. 2) The mass stored in the fracture responses quickly to water flushing, while the mass stored in the rock matrix is much less sensitive to the water flushing. 3) The diffusive mass exchange during the water flushing phase has similar patterns under symmetric and asymmetric cases. 4) The characteristic distance

Geological evolution of the Iraqi Mesopotamia Foredeep, inner platform and near surroundings of the Arabian Plate

Science.gov (United States)

Sissakian, Varoujan K.

2013-08-01

The Iraqi territory could be divided into four main tectonic zones; each one has its own characteristics concerning type of the rocks, their age, thickness and structural evolution. These four zones are: (1) Inner Platform (stable shelf), (2) Outer Platform (unstable shelf), (3) Shalair Zone (Terrain), and (4) Zagros Suture Zone. The first two zones of the Arabian Plate lack any kind of metamorphism and volcanism. The Iraqi territory is located in the extreme northeastern part of the Arabian Plate, which is colliding with the Eurasian (Iranian) Plate. This collision has developed a foreland basin that includes: (1) Imbricate Zone, (2) High Folded Zone, (3) Low Folded Zone and (4) Mesopotamia Foredeep. The Mesopotamia Foredeep, in Iraq includes the Mesopotamia Plain and the Jazira Plain; it is less tectonically disturbed as compared to the Imbricate, High Folded and Low Folded Zones. Quaternary alluvial sediments of the Tigris and Euphrates Rivers and their tributaries as well as distributaries cover the central and southeastern parts of the Foredeep totally; it is called the Mesopotamian Flood Plain. The extension of the Mesopotamia Plain towards northwest however, is called the Jazira Plain, which is covered by Miocene rocks. The Mesopotamia Foredeep is represented by thick sedimentary sequence, which thickens northwestwards including synrift sediments; especially of Late Cretaceous age, whereas on surface the Quaternary sediments thicken southeastwards. The depth of the basement also changes from 8 km, in the west to 14 km, in the Iraqi-Iranian boarders towards southeast. The anticlinal structures have N-S trend, in the extreme southern part of the Mesopotamia Foredeep and extends northwards until the Latitude 32°N, within the Jazira Plain, there they change their trends to NW-SE, and then to E-W trend. The Mesozoic sequence is almost without any significant break, with increase in thickness from the west to the east, attaining 5 km. The sequence forms the main

Global Models of Ridge-Push Force, Geoid, and Lithospheric Strength of Oceanic plates

Science.gov (United States)

Mahatsente, Rezene

2017-12-01

An understanding of the transmission of ridge-push related stresses in the interior of oceanic plates is important because ridge-push force is one of the principal forces driving plate motion. Here, I assess the transmission of ridge-push related stresses in oceanic plates by comparing the magnitude of the ridge-push force to the integrated strength of oceanic plates. The strength is determined based on plate cooling and rheological models. The strength analysis includes low-temperature plasticity (LTP) in the upper mantle and assumes a range of possible tectonic conditions and rheology in the plates. The ridge-push force has been derived from the thermal state of oceanic lithosphere, seafloor depth and crustal age data. The results of modeling show that the transmission of ridge-push related stresses in oceanic plates mainly depends on rheology and predominant tectonic conditions. If a lithosphere has dry rheology, the estimated strength is higher than the ridge-push force at all ages for compressional tectonics and at old ages (>75 Ma) for extension. Therefore, under such conditions, oceanic plates may not respond to ridge-push force by intraplate deformation. Instead, the plates may transmit the ridge-push related stress in their interior. For a wet rheology, however, the strength of young lithosphere (stress may dissipate in the interior of oceanic plates and diffuses by intraplate deformation. The state of stress within a plate depends on the balance of far-field and intraplate forces.

A new heat flux model for the Antarctic Peninsula incorporating spatially variable upper crustal radiogenic heat production

Science.gov (United States)

Burton-Johnson, A.; Halpin, J.; Whittaker, J. M.; Graham, F. S.; Watson, S. J.

2017-12-01

We present recently published findings (Burton-Johnson et al., 2017) on the variability of Antarctic sub-glacial heat flux and the impact from upper crustal geology. Our new method reveals that the upper crust contributes up to 70% of the Antarctic Peninsula's subglacial heat flux, and that heat flux values are more variable at smaller spatial resolutions than geophysical methods can resolve. Results indicate a higher heat flux on the east and south of the Peninsula (mean 81 mWm-2) where silicic rocks predominate, than on the west and north (mean 67 mWm-2) where volcanic arc and quartzose sediments are dominant. Whilst the data supports the contribution of HPE-enriched granitic rocks to high heat flux values, sedimentary rocks can be of comparative importance dependent on their provenance and petrography. Models of subglacial heat flux must utilize a heterogeneous upper crust with variable radioactive heat production if they are to accurately predict basal conditions of the ice sheet. Our new methodology and dataset facilitate improved numerical model simulations of ice sheet dynamics. The most significant challenge faced remains accurate determination of crustal structure, particularly the depths of the HPE-enriched sedimentary basins and the sub-glacial geology away from exposed outcrops. Continuing research (particularly detailed geophysical interpretation) will better constrain these unknowns and the effect of upper crustal geology on the Antarctic ice sheet. Burton-Johnson, A., Halpin, J.A., Whittaker, J.M., Graham, F.S., and Watson, S.J., 2017, A new heat flux model for the Antarctic Peninsula incorporating spatially variable upper crustal radiogenic heat production: Geophysical Research Letters, v. 44, doi: 10.1002/2017GL073596.

From vein precipitates to deformation and fluid rock interaction within a SSZ: Insights from the Izu-Bonin-Mariana fore arc

Science.gov (United States)

Micheuz, Peter; Quandt, Dennis; Kurz, Walter

2017-04-01

International Ocean Discovery Program (IODP) expeditions 352 and 351 drilled through oceanic crust of the Philippine Sea plate. The two study areas are located near the outer Izu-Bonin-Mariana (IBM) fore arc and in the Amami Sankaku Basin. The primary objective was to improve our understanding of supra-subduction zones (SSZ) and the process of subduction initiation. The recovered drill cores during IODP expedition 352 represent approximately 50 Ma old fore arc basalts (FAB) and boninites revealing an entire volcanic sequence of a SSZ. Expedition 351 drilled FAB like oceanic crust similar in age to the FABs of expedition 352. In this study we present data on vein microstructures, geochemical data and isotopic signatures of vein precipitates to give new insights into fluid flow and precipitation processes and deformation within the Izu-Bonin fore arc. Veins formed predominantly as a consequence of hydrofracturing resulting in the occurrence of branched vein systems and brecciated samples. Along these hydrofractures the amount of altered host rock fragments varies and locally alters the host rock completely to zeolites and carbonates. Subordinately extensional veins released after the formation of the host rocks. Cross-cutting relationships of different vein types point to multiple fracturing events subsequently filled with minerals originating from a fluid with isotopic seawater signature. Based on vein precipitates, their morphology and their growth patterns four vein types have been defined. Major vein components are (Mg-) calcite and various zeolites determined by Raman spectra and electron microprobe analyses. Zeolites result from alteration of volcanic glass during interaction with a seawaterlike fluid. Type I veins which are characterized by micritic infill represent neptunian dykes. They predominantly occur in the upper levels of drill cores being the result of an initial volume change subsequently to crystallization of the host rocks. Type II veins are

Elbow, forearm, wrist, and hand injuries among sport rock climbers.

Science.gov (United States)

Holtzhausen, L M; Noakes, T D

1996-07-01

Sport rock climbing with its repetitive high-torque movements in gaining the ascent of a rock face or wall, often in steep overhanging positions, is associated with a unique distribution and form of upper limb injuries. In this article, we review the biomechanical aspects of sport rock climbing and the types of injuries commonly encountered in the forearm, wrist, and hand regions of elite sport rock climbers. Because elbow, forearm, wrist, and hand injuries predominate, representing 62% of the total injuries encountered, these anatomical areas have been selected for review. The predominant source of data are the published work of Bollen et al. The remaining sources were obtained through electronic search of the Medline and Current Contents Databases (last searched May 1995). German and French articles were included in the search criteria. Only studies dealing with acute soft tissue and overuse injuries amongst sport rock climbers were selected. Data were extracted directly from the sourced articles. The following injuries have been described in detail with regard to their presentation, diagnosis, treatment, and prevention amongst sport rock climbers: medial epicondylitis, brachialis tendonitis, biceps brachii tendonitis, ulnar collateral ligament sprain of the elbow, carpal tunnel syndrome, digital flexor tendon pulley sheath tears, interphalangeal joint effusions, fixed flexion deformities of the interphalangeal joints, and collateral ligament tears of the interphalangeal joints. Many of the injuries are specific to the handhold types used by the rock climber. Accurate diagnosis and effective treatment of these unique injuries will be facilitated by a wider understanding of the biomechanical aspects of rock climbing and an awareness of the patterns and incidence of injuries in this sport.

Isotopic feature and uranium dating of the volcanic rocks in the Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

Volcanic rocks from the northern and middle Okinawa Trough were dated by uranium-series dating method. Differential fractions using magnetic procedure were designed to separate samples. New report on the ages and isotopic data of rocks in the northern trough (especially black pumice) was discussed. Based on the uranium dates and Sr-Nd isotopic ratio, magmatic evolution process of the Okinawa Trough was noted. Firstly, there have been wide silicic volcanic activities in the Okinawa Trough from late Pleistocene to present, and the volcanic rocks can be divided into three subgroups. Secondly, magma generally came from PREMA source area under the Okinawa Trough. Magmatic evolution in the northern trough was similar to the middle, but different to the south. Finally, volcanic activities indicated that opening of the southern Okinawa Trough did not happen due to the collision between Luson Arc and Eurasian Plate until the early Pleistocene.

Thermal Inertia of Rocks and Rock Populations

Science.gov (United States)

Golombek, M. P.; Jakosky, B. M.; Mellon, M. T.

2001-01-01

The effective thermal inertia of rock populations on Mars and Earth is derived from a model of effective inertia versus rock diameter. Results allow a parameterization of the effective rock inertia versus rock abundance and bulk and fine component inertia. Additional information is contained in the original extended abstract.

Eco-engineered rock pools: a concrete solution to biodiversity loss and urban sprawl in the marine environment

Science.gov (United States)

Firth, Louise B.; Browne, Keith A.; Knights, Antony M.; Hawkins, Stephen J.; Nash, Róisín

2016-09-01

In coastal habitats artificial structures typically support lower biodiversity and can support greater numbers of non-native and opportunistic species than natural rocky reefs. Eco-engineering experiments are typically trialed to succeed; but arguably as much is learnt from failure than from success. Our goal was to trial a generic, cost effective, eco-engineering technique that could be incorporated into rock armouring anywhere in the world. Artificial rock pools were created from manipulated concrete between boulders on the exposed and sheltered sides of a causeway. Experimental treatments were installed in locations where they were expected to fail and compared to controls installed in locations in which they were expected to succeed. Control pools were created lower on the structure where they were immersed on every tidal cycle; experimental pools were created above mean high water spring tide which were only immersed on spring tides. We hypothesised that lower and exposed pools would support significantly higher taxon and functional diversity than upper and sheltered pools. The concrete pools survived the severe winter storms of 2013/14. After 12 months, non-destructive sampling revealed significantly higher mean taxon and functional richness in lower pools than upper pools on the exposed side only. After 24 months the sheltered pools had become inundated with sediments, thus failing to function as rock pools as intended. Destructive sampling on the exposed side revealed significantly higher mean functional richness in lower than upper pools. However, a surprisingly high number of taxa colonised the upper pools leading to no significant difference in mean taxon richness among shore heights. A high number of rare taxa in the lower pools led to total taxon richness being almost twice that of upper pools. These findings highlight that even when expected to fail concrete pools supported diverse assemblages, thus representing an affordable, replicable means of

Transient thermal stresses in an orthotropic finite rectangular plate due to arbitrary surface heat-generations

International Nuclear Information System (INIS)

Sugano, Y.

1980-01-01

The transient thermal stresses in an orthotropic finite rectangular plate due to arbitrary surface heat-generations on two edges are studied by means of the Airy stress function. The purposes of this paper are to present a method of determing the transient thermal stresses in an orthographic rectangular plate with four edges of distinct thermal boundary condition of the third kind which exactly satisfy the traction-free conditions of shear stress over all boundaries including four corners of the plate, and to consider the effects of the anisotropies of material properties and the convective heat transfer on the upper and lower surfaces on the thermal stress distribution. (orig.)

Dynamics of interplate domain in subduction zones: influence of rheological parameters and subducting plate age

Directory of Open Access Journals (Sweden)

D. Arcay

2012-12-01

Full Text Available The properties of the subduction interplate domain are likely to affect not only the seismogenic potential of the subduction area but also the overall subduction process, as it influences its viability. Numerical simulations are performed to model the long-term equilibrium state of the subduction interplate when the diving lithosphere interacts with both the overriding plate and the surrounding convective mantle. The thermomechanical model combines a non-Newtonian viscous rheology and a pseudo-brittle rheology. Rock strength here depends on depth, temperature and stress, for both oceanic crust and mantle rocks. I study the evolution through time of, on one hand, the brittle-ductile transition (BDT depth, z_BDT, and, on the other hand, of the kinematic decoupling depth, z_dec, simulated along the subduction interplate. The results show that both a high friction and a low ductile strength at the asthenospheric wedge tip shallow z_BDT. The influence of the weak material activation energy is of second order but not negligible. z_BDT becomes dependent on the ductile strength increase with depth (activation volume if the BDT occurs at the interplate decoupling depth. Regarding the interplate decoupling depth, it is shallowed (1 significantly if mantle viscosity at asthenospheric wedge tip is low, (2 if the difference in mantle and interplate activation energy is weak, and (3 if the activation volume is increased. Very low friction coefficients and/or low asthenospheric viscosities promote z_BDT = z_dec. I then present how the subducting lithosphere age affects the brittle-ductile transition depth and the kinematic decoupling depth in this model. Simulations show that a rheological model in which the respective activation energies of mantle and interplate material are too close hinders the mechanical decoupling at the down-dip extent of the interplate

The Evolution of Plate and Extruded Products with High Strength and Fracture Toughness

Science.gov (United States)

Denzer, D. K.; Rioja, R. J.; Bray, G. H.; Venema, G. B.; Colvin, E. L.

From the first use of 2017-T74 on the Junkers F13, improvements have been made to plate and extruded products for applications requiring the highest attainable strength and adequate fracture toughness. One such application is the upper wing of large aircraft. The progression of these product improvements achieved through the development of alloys that include 7075-(T6 & T76), 7150-(T6 & T77) and 7055-(T77 & T79) and most recently 7255-(T77 & T79) is reviewed. The most current advancements include aluminum-copper-lithium, alloy 2055 plate and extruded products that can attain strength equivalent to that of 7055-T77 with higher modulus, similar fracture toughness and improved fatigue, fatigue crack growth and corrosion performance. The achievement of these properties is explained in terms of the several alloy design principles. The highly desired and balanced characteristics make these products ideal for upper wing applications.

Hydrodynamics of a flexible plate between pitching rigid plates

Science.gov (United States)

Kim, Junyoung; Kim, Daegyoum

2017-11-01

The dynamics of a flexible plate have been studied as a model problem in swimming and flying of animals and fluid-structure interaction of plants and flags. Motivated by fish schooling and an array of sea grasses, we investigate the dynamics of a flexible plate closely placed between two pitching rigid plates. In most studies on passive deformation of the flexible plate, the plate is immersed in a uniform flow or a wavy flow. However, in this study, the flexible plate experiences periodic deformation by the oscillatory flow generated by the prescribed pitching motion of the rigid plates. In our model, the pitching axes of the rigid plates and the clamping position of the flexible plate are aligned on the same line. The flexible plate shows various responses depending on length and pitching frequency of rigid plates, thickness of a flexible plate, and free-stream velocity. To find the effect of each variable on the response of the flexible plate, amplitude of a trailing edge and modal contribution of a flapping motion are compared, and flow structure around the flexible plate is examined.

SID seeks sludge and foreign bodies in steam generator upper heads while CECIL robotically removes them

International Nuclear Information System (INIS)

Ashton, A.T.; Gay, J.

1993-01-01

The CECIL [Consolidated Edison Combined Inspection and Lancing] system provides a range of maintenance tools for cleaning the region between the tubesheet and the first support plate in steam generators. SID [Secondary Inspection Device] extends access to and inspection of the upper bundle region. Work is being done to combine CECIL and SID technology to inspect and hydraulically clean the upper bundle. (Author)

A vapor generator equipped with an advanced drain device for the secondary side of the tubes plate

International Nuclear Information System (INIS)

Valadon, C.

1995-01-01

A draining design is proposed for the tube plate secondary side in a PWR type reactor, that does not interfere with the water flush 'street' thus allowing for an easy inspection and maintenance in the lower part of the tube bundle. The draining system is composed of a main groove on the upper side of the tube plate, which is connected to draining means situated outside the vapor generator. 6 fig

The influence of upper-crust lithology on topographic development in the central Coast Ranges of California

Science.gov (United States)

Garcia, A.F.; Mahan, S.A.

2012-01-01

A fundamental geological tenet is that as landscapes evolve over graded to geologic time, geologic structures control patterns of topographic distribution in mountainous areas such that terrain underlain by competent rock will be higher than terrain underlain by incompetent rock. This paper shows that in active orogens where markedly weak and markedly strong rocks are juxtaposed along contacts that parallel regional structures, relatively high topography can form where strain is localized in the weak rock. Such a relationship is illustrated by the topography of the central Coast Ranges between the Pacific coastline and the San Andreas fault zone (SAFZ), and along the length of the Gabilan Mesa (the "Gabilan Mesa segment" of the central Coast Ranges). Within the Gabilan Mesa segment, the granitic upper crust of the Salinian terrane is in contact with the accretionary-prism m??lange upper crust of the Nacimiento terrane along the inactive Nacimiento fault zone. A prominent topographic lineament is present along most of this lithologic boundary, approximately 50 to 65. km southwest of the SAFZ, with the higher topography formed in the m??lange on the southwest side of the Nacimiento fault. This paper investigates factors influencing the pattern of topographic development in the Gabilan Mesa segment of the central Coast Ranges by correlating shortening magnitude with the upper-crust compositions of the Salinian and Nacimiento terranes. The fluvial geomorphology of two valleys in the Gabilan Mesa, which is within the Salinian terrane, and alluvial geochronology based on optically-stimulated luminescence (OSL) age estimates, reveal that the magnitude of shortening accommodated by down-to-the-southwest tilting of the mesa since 400ka is less than 1 to 2m. Our results, combined with those of previous studies, indicate that at least 63% to 78% of late-Cenozoic, northeast-southwest directed, upper-crustal shortening across the Gabilan Mesa segment has been accommodated

Gentilly 2 steam generators Spring 2000 outage: tubesheet waterlance cleaning and inspection; upper bundle inspection

International Nuclear Information System (INIS)

Akeroyd, J.K.; Plante, S.

2000-01-01

A review of the secondary side maintenance activities recently completed during the Gentilly 2 Annual Spring 2000 Maintenance Outage. Activities included: 1) Tubesheet intertube waterlance cleaning and visual inspection, 2) First tube support plate, in-bundle visual inspection of the hot leg, and 3) Upper bundle tube support plate visual inspection. A description of the waterlancing and inspection equipment and setup in the RB at Gentilly 2 is provided. Several innovative techniques were successfully employed and yielded savings in critical path duration, labour and personnel radiation dose. These included accessing the SG tubesheet region through one handhole only and sludge removal utilizing the SG blowdown system. Plant personnel judged tubesheet sludge removal successful. Before and after results of the cleaning process along with samples of the visual inspection results are provided. Inspection of the first support plate, which was a repeat of an inspection done in 1997, was conducted along with an in-bundle inspection of the upper tube supports. Results are presented along with a discussion of the implications for future steam generator maintenance. (author)

Processes accompanying of mantle plume emplacement into continental lithosphere: Evidence from NW Arabian plate, Western Syria

Science.gov (United States)

Sharkov, E. V.

2015-12-01

Lower crustal xenoliths occurred in the Middle Cretaceous lamprophyre diatremes in Jabel Ansaria (Western Syria) (Sharkov et al., 1992). They are represented mainly garnet granulites and eclogite-like rocks, which underwent by deformations and retrograde metamorphism, and younger fresh pegmatoid garnet-kaersutite-clinopyroxene (Al-Ti augite) rocks; mantle peridotites are absent in these populations. According to mineralogical geothermobarometers, forming of garnet-granulite suite rocks occurred under pressure 13.5-15.4 kbar (depths 45-54 kn) and temperature 965-1115oC. At the same time, among populations of mantle xenoliths in the Late Cenozoic platobasalts of the region, quite the contrary, lower crustal xenoliths are absent, however, predominated spinel lherzolites (fragments of upper cooled rim of a plume head), derived from the close depths (30-40 km: Sharkov, Bogatikov, 2015). From this follows that ancient continental crust was existed here even in the Middle Cretaceous, but in the Late Cenozoic was removed by extended mantle plume head; at that upper sialic crust was not involved in geomechanic processes, because Precambrian metamorphic rocks survived as a basement for Cambrian to Cenozoic sedimentary cover of Arabian platform. In other words, though cardinal rebuilding of deep-seated structure of the region occurred in the Late Cenozoic but it did not affect on the upper shell of the ancient lithosphere. Because composition of mantle xenolithis in basalts is practically similar worldwide, we suggest that deep-seated processes are analogous also. As emplacement of the mantle plume heads accompanied by powerful basaltic magmatism, very likely that range of lower (mafic) continental crust existence is very convenient for extension of plume heads and their adiabatic melting. If such level, because of whatever reasons, was not reached, melting was limited but appeared excess of volatile matters which led to forming of lamprophyre or even kimberlite.

Contributions to the petrography, geochemistry and geochronology (U-Pb and Sm-Nd) of the Paleoproterozoic effusive rocks from Iricoume Group, Amazonian Craton, Brazil

Energy Technology Data Exchange (ETDEWEB)

Marques, Suelen Nonata de Souza; Nascimento, Rielva Solimairy Campelo do, E-mail: suelen-marques@hotmail.com, E-mail: rielva@ufam.edu.br [Universidade Federal do Amazonas (UFAM), Manaus, AM (Brazil). Inst. de Geociencias; Souza, Valmir da Silva; Dantas, Elton Luiz, E-mail: vsouza@unb.br, E-mail: elton@unb.br [Universidade de Brasilia (UnB), DF (Brazil). Inst. de Geociencias; Valerio, Cristovao da Silva, E-mail: cristovao@igeo.ufrr.br [Universidade Federal de Roraima (UFRR), Boa Vista, RR (Brazil). Inst. de Geociencias

2014-07-01

The southernmost region of the Guyana shield, Amazonian craton, hosts large record of Paleoproterozoic effusive rocks of the Iricoume Group. They present remarkably well-preserved igneous textures and structures. The SiO{sub 2} contents reveal a bimodal association marked by a compositional gap between acid (SiO{sub 2} > 67 wt%) and intermediate (SiO{sub 2} < 57.7 wt%) rocks. The acid effusive rocks are rhyolites to rhyodacites with high SiO{sub 2}, alkali, Rb, Zr, Nb + Ta, La + Ce and 104 Ga/Al content and low Fe{sub 2}O{sub 3tot}, TiO{sub 2}, CaO, Sr and Co content. They exhibit subalkaline, metaluminous-to-peraluminous compositions, and geochemically compatible to A-type magmatism emplaced in post-collisional to within-plate tectonic settings. The intermediate rocks are andesitic/basalt to andesite relatively high contents of TiO{sub 2}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3total}, MgO, CaO, Sr and Co; low SiO{sub 2}, K{sub 2}O, Rb, Zr, Nb + Ta, La + Ce. They have subalkaline and metaluminous geochemical composition and plot on within-plate basalt field. The acid rocks crystallized at 1882 ± 11 Ma in U-Pb analyses for LA-MC-ICPMS zircon data. The Sm-Nd isotopic data on all rocks reveal a Nd TDM model ages between 2.59 and 2.16 Ga and ε{sub Nd}(t) values between -5.78 and 0.03, indicate that the magmatic evolution was related to the reworking of older Paleoproterozoic at the Rhyacian-Siderian period, continental crust (Transamazonian crust-forming event) with some mixing with a limited amount mantle-derived magmas or with contamination by Archean crust. The petrographic, geochemical and geochronological data presented in this paper suggest a within-plate to post-collisional tectonic setting for the Iricoume volcanism, involving lower crust uplift and generation of basalt magma in an extensional regime. (author)

First data on the age of rocks from the central part of the Vitoria-Trindade Ridge (Brazil Basin, South Atlantic)

Science.gov (United States)

Skolotnev, S. G.; Bylinskaya, M. E.; Golovina, L. A.; Ipat'eva, I. S.

2011-03-01

Micropaleontological and isotope-geochronological investigations of calcareous sedimentary rocks and volcanites dredged out from the central portion of the submarine Vitoria-Trindade Ridge during the 24th cruise of R/V Akademik Vavilov have been conducted. It has been established based on micropaleontological analysis, which included determination of the species composition of foraminifera and nannoplankton, that the sequence of sedimentary rocks having a pelagic nature formed on the slopes of the volcanic seamounts in the central portion of the Vitoria-Trindade Ridge from the Early to Mid-Miocene to the Holocene; a good correlation between the degree of lithification of these rocks and their age is observed. It has also been established that the carbonate platforms on the abraded tops of the Davis Seamount and the Dogaressa Bank, which are located in the east-central portion of the Vitoria-Trindade Ridge, started forming in the Early Miocene (19-24 Ma). It has been determined using local U-Pb dating of zircon grains with a SHRIMP-II high resolution secondary ion mass spectrometer that the volcanites forming the upper portion of the volcanic rock sequence of the Jaseur Seamount (29.8 ± 6.6 Ma) located in the west-central portion of the Vitoria-Trindade Ridge date to the Oligocene. The investigations conducted have confirmed the opinion that the Vitoria-Trindade Ridge formed in general because of the activity of the hot spot located under the volcanic Trindade and Martin Vaz Islands. However, separate extended lenticular segments of this ridge existed for a long time as single structures, within which the age of the seamounts was not linearly dependent on the distance from the location of the hot spot. Lenses of hot mantle matter that form at the sublithospheric level as a result of impulses of plume activity and move along with the lithospheric plate play a defining role in the development of individual segments forming the Vitoria-Trindade Ridge.

Tomographic Imaging of the Lesser Antilles Subducted Slab and its Significance for Estimating the Age and Amount of Eastward Motion of the Overriding Caribbean Plate

Science.gov (United States)

Mann, P.; Chen, Y. W.; Wu, J.; Suppe, J.

2017-12-01

The idea of a Pacific-derived and eastward-transported Caribbean and Scotia plates was first proposed by J. Tuzo Wilson in 1966. Wilson proposed that the motion of these two, small plates was analogous to "ice rafting" observed on frozen lakes and oceans when a narrow ( 50 m) strip of ice is forced over a lower plate of ice. In the Caribbean the upper plate corresponds to the 750 km-long, north-south length of the Lesser Antilles volcanic arc ranging in thickness from 20-30 km while its subducting plate is Atlantic Cretaceous oceanic crust of 8-10 km thickness and subducting at an angle of 45º to a depth of 300 km into the mantle. We estimated the length of the Lesser Antilles slab from MIT P-wave global tomography (MITP08; Li et al., 2008) and compared to published transects from Utrecht UUP-07 global tomography (van Bentham et al., 2013). The measured slab lengths vary from 1550 km (Utrecht) to 1250 km (MIT). We then unfolded both slabs to the Earth's surface, and used GPlates to restore the leading edge of the Caribbean plate at the time of the Lesser Antilles slab's initial subduction. The Middle Eocene (49 Ma) reconstruction realigns the proto-Lesser Antilles arc and leading edge of the Caribbean plate in a continuous arc with older arc rocks in Cuba. During this Middle Eocene period of abrupt tectonic transition, the Cuban arc segment was terminated on its northeastward path by collision with the Bahama carbonate platform with subsequent reorientation onto its present, east-west path into the central Atlantic Ocean from 49-0 Ma. This collision/plate reorientation event is independently recorded by: 1) a poorly defined Greater Antilles slab seen on tomography that is aligned with the Cuban arc; 2) identical initiation ages of 49 Ma for the Cayman trough pull-apart and the Lesser Antilles slab; and 3) similarity in lengths for the length of the subducted, Lesser Antilles slab ( 1250-1550 km) and the length of the Cayman trough pull-apart basin ( 1100 km). East

Upper Cretaceous to Pleistocene melilitic volcanic rocks of the Bohemian Massif: Petrology and mineral chemistry

Czech Academy of Sciences Publication Activity Database

Skála, Roman; Ulrych, Jaromír; Krmíček, Lukáš; Fediuk, F.; Balogh, K.; Hegner, E.

2015-01-01

Roč. 66, č. 3 (2015), s. 197-216 ISSN 1335-0552 Institutional support: RVO:67985831 Keywords : Bohemian Massif * Cenozoic volcanism * isotope geochemistry * melilitic rock * mineralogy * petrology Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.523, year: 2015

Comparison of BR3 Surveillance and Vessel Plates to the Surrogate Plates Representative of the Yankee Rowe PWR Vessel

Energy Technology Data Exchange (ETDEWEB)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G

1998-07-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ( 260 degrees Celsius) and their plates were austenitized a higher-than-usual temperature (970 degrees Celsius) - a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behaviour characterized by a 41 J Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rate plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares free complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63 % (A533-B) and YA9, 0.19 (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and

Comparison of BR3 Surveillance and Vessel Plates to the Surrogate Plates Representative of the Yankee Rowe PWR Vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

1998-07-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ( 260 degrees Celsius) and their plates were austenitized a higher-than-usual temperature (970 degrees Celsius) - a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behaviour characterized by a 41 J Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rate plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares free complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63 % (A533-B) and YA9, 0.19 (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and

Comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe PWR vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

1999-01-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature (∼260 C) and their plates were austenitized at higher-than-usual temperature (∼970 C) -- a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behavior characterized by a 41J. Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program; this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel

Power training using pneumatic machines vs. plate-loaded machines to improve muscle power in older adults.

Science.gov (United States)

Balachandran, Anoop T; Gandia, Kristine; Jacobs, Kevin A; Streiner, David L; Eltoukhy, Moataz; Signorile, Joseph F

2017-11-01

Power training has been shown to be more effective than conventional resistance training for improving physical function in older adults; however, most trials have used pneumatic machines during training. Considering that the general public typically has access to plate-loaded machines, the effectiveness and safety of power training using plate-loaded machines compared to pneumatic machines is an important consideration. The purpose of this investigation was to compare the effects of high-velocity training using pneumatic machines (Pn) versus standard plate-loaded machines (PL). Independently-living older adults, 60years or older were randomized into two groups: pneumatic machine (Pn, n=19) and plate-loaded machine (PL, n=17). After 12weeks of high-velocity training twice per week, groups were analyzed using an intention-to-treat approach. Primary outcomes were lower body power measured using a linear transducer and upper body power using medicine ball throw. Secondary outcomes included lower and upper body muscle muscle strength, the Physical Performance Battery (PPB), gallon jug test, the timed up-and-go test, and self-reported function using the Patient Reported Outcomes Measurement Information System (PROMIS) and an online video questionnaire. Outcome assessors were blinded to group membership. Lower body power significantly improved in both groups (Pn: 19%, PL: 31%), with no significant difference between the groups (Cohen's d=0.4, 95% CI (-1.1, 0.3)). Upper body power significantly improved only in the PL group, but showed no significant difference between the groups (Pn: 3%, PL: 6%). For balance, there was a significant difference between the groups favoring the Pn group (d=0.7, 95% CI (0.1, 1.4)); however, there were no statistically significant differences between groups for PPB, gallon jug transfer, muscle muscle strength, timed up-and-go or self-reported function. No serious adverse events were reported in either of the groups. Pneumatic and plate

Homogenization of a thermal problem with the fourier conditions in the thin plates of a heat exchanger

International Nuclear Information System (INIS)

Rahmattulla, A.A.; Taghite, M.B.

1996-01-01

In this paper was studied a thermal problem with the fourier boundary conditions on the edges of the holes in a periodically perforated plate of a heat exchanger. This problem contains several reduced parameters which can be very small (the period ε of the distribution of the holes, the reduced thickness e of the plate and the three Biot numbers relative to the different parts of the boundary). The homogenization technique was used to estimate the field of temperatures attainable in the upper plate, depending on the relative order of magnitude of the smell parameters. (authors). 9 refs

Rock pushing and sampling under rocks on Mars

Science.gov (United States)

Moore, H.J.; Liebes, S.; Crouch, D.S.; Clark, L.V.

1978-01-01

Viking Lander 2 acquired samples on Mars from beneath two rocks, where living organisms and organic molecules would be protected from ultraviolet radiation. Selection of rocks to be moved was based on scientific and engineering considerations, including rock size, rock shape, burial depth, and location in a sample field. Rock locations and topography were established using the computerized interactive video-stereophotogrammetric system and plotted on vertical profiles and in plan view. Sampler commands were developed and tested on Earth using a full-size lander and surface mock-up. The use of power by the sampler motor correlates with rock movements, which were by plowing, skidding, and rolling. Provenance of the samples was determined by measurements and interpretation of pictures and positions of the sampler arm. Analytical results demonstrate that the samples were, in fact, from beneath the rocks. Results from the Gas Chromatograph-Mass Spectrometer of the Molecular Analysis experiment and the Gas Exchange instrument of the Biology experiment indicate that more adsorbed(?) water occurs in samples under rocks than in samples exposed to the sun. This is consistent with terrestrial arid environments, where more moisture occurs in near-surface soil un- der rocks than in surrounding soil because the net heat flow is toward the soil beneath the rock and the rock cap inhibits evaporation. Inorganic analyses show that samples of soil from under the rocks have significantly less iron than soil exposed to the sun. The scientific significance of analyses of samples under the rocks is only partly evaluated, but some facts are clear. Detectable quantities of martian organic molecules were not found in the sample from under a rock by the Molecular Analysis experiment. The Biology experiments did not find definitive evidence for Earth-like living organisms in their sample. Significant amounts of adsorbed water may be present in the martian regolith. The response of the soil

A review of the paleomagnetic data from Cretaceous to lower Tertiary rocks from Vietnam, Indochina and South China, and their implications for Cenozoic tectonism in Vietnam and adjacent areas

Science.gov (United States)

Cung, Thu'ọ'ng Chí; Geissman, John W.

2013-09-01

Available paleomagnetic data from rock formations of Cretaceous age from Vietnam, Indochina and South China are compiled and reviewed in the context of their tectonic importance in a common reference frame with respect to Eurasia's coeval paleopoles. Key factors that play an important role in determining the reliability of a paleomagnetic result for utilization in tectonic studies have been taken into consideration and include the absence of evidence of remagnetization, which is a feature common to many rocks in this region. Overall, the Cretaceous paleomagnetic data from the South China Block show that the present geographic position of the South China Block has been relatively stable with respect to Eurasia since the mid-Cretaceous and that the paleomagnetically detected motion of a coherent lithospheric block must be based on the representative data obtained from different specific localities across the block in order to separate more localized, smaller scale deformation from true lithosphere scale motion (translation and/or rotation) of a tectonic block. Cretaceous to early Tertiary paleomagnetic data from the Indochina-Shan Thai Block reveal complex patterns of intra-plate deformation in response to the India-Eurasia collision. Paleomagnetically detected motions from the margins of tectonic blocks are interpreted to mainly reflect displacement of upper crustal blocks due to folding and faulting processes. Rigid, lithosphere scale block rotation is not necessarily supported by the paleomagnetic data. The paleomagnetic results from areas east and south of the Red River fault system suggest that this major transcurrent fault system has had a complicated slip history through much of the Cenozoic and that it does not demarcate completely non-rotated and significantly rotated parts of the crust in this area. However, most paleomagnetic results from areas east and south of the Red River fault system at the latitude of Yunnan Province are consistent with a very modest

Inverse models of plate coupling and mantle rheology: Towards a direct link between large-scale mantle flow and mega thrust earthquakes

Science.gov (United States)

Gurnis, M.; Ratnaswamy, V.; Stadler, G.; Rudi, J.; Liu, X.; Ghattas, O.

2017-12-01

We are developing high-resolution inverse models for plate motions and mantle flow to recover the degree of mechanical coupling between plates and the non-linear and plastic parameters governing viscous flow within the lithosphere and mantle. We have developed adjoint versions of the Stokes equations with fully non-linear viscosity with a cost function that measures the fit with plate motions and with regional constrains on effective upper mantle viscosity (from post-glacial rebound and post seismic relaxation). In our earlier work, we demonstrate that when the temperature field is known, the strength of plate boundaries, the yield stress and strain rate exponent in the upper mantle are recoverable. As the plate boundary coupling drops below a threshold, the uncertainty of the inferred parameters increases due to insensitivity of plate motion to plate coupling. Comparing the trade-offs between inferred rheological parameters found from a Gaussian approximation of the parameter distribution and from MCMC sampling, we found that the Gaussian approximation—which is significantly cheaper to compute—is often a good approximation. We have extended our earlier method such that we can recover normal and shear stresses within the zones determining the interface between subducting and over-riding plates determined through seismic constraints (using the Slab1.0 model). We find that those subduction zones with low seismic coupling correspond with low inferred values of mechanical coupling. By fitting plate motion data in the optimization scheme, we find that Tonga and the Marianas have the lowest values of mechanical coupling while Chile and Sumatra the highest, among the subduction zones we have studies. Moreover, because of the nature of the high-resolution adjoint models, the subduction zones with the lowest coupling have back-arc extension. Globally we find that the non-linear stress-strain exponent, n, is about 3.0 +/- 0.25 (in the upper mantle and lithosphere) and a

Vibration measurement for evaluating the danger of rock-collapse; Rakuseki kikendo hantei no tame no shindo sokutei

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, T; Harada, H [The Nippon Road Co. Ltd., Tokyo (Japan); Mitsuzuka, T [Chishitsu-Keisoku Co. Ltd., Tokyo (Japan)

1997-10-22

Discussions were given on feasibility of a method for investigating a problem of the danger of rock-collapse by applying vibration measurement. The measurement investigation was carried out at a mouth of a tunnel under construction on a highway where the danger of rock-collapse is being investigated according to a qualitative determination criterion. Sixty-four rocks have been evaluated of their danger, with the degree of the danger having been classified to ranks one to three. Vibration measurement was performed on five floating rocks out of the 64 rocks. Vibroscopes were installed on upper portion of the rocks to be investigated and on exposed rocks nearby. The measurement revealed that the vibration has nearly the same amplitude in both of the floating rocks and the settled rocks before and after an automobile has passed, but the floating rocks shake more strongly than the settled rocks while an automobile is passing. This trend appears more noticeably in rocks regarded unstable in the danger determining investigation, indicating presence of close relationship between wave amplitude excited by the automobile and adhesion of the floating rocks. As a result of the discussions, it was made clear that the maximum amplitude ratio and the spectral ratio among the vibration characteristics of the floating rocks can be used as effective determination criteria. 2 refs., 7 figs., 2 tabs.

Doubling inequalities for anisotropic plate equations and applications to size estimates of inclusions

International Nuclear Information System (INIS)

Di Cristo, M; Lin, C-L; Morassi, A; Rosset, E; Vessella, S; Wang, J-N

2013-01-01

We prove the upper and lower estimates of the area of an unknown elastic inclusion in a thin plate by one boundary measurement. The plate is made of non-homogeneous linearly elastic material belonging to a general class of anisotropy and the domain of the inclusion is a measurable subset of the plate. The size estimates are expressed in terms of the work exerted by a couple field applied at the boundary and of the induced transversal displacement and its normal derivative taken at the boundary of the plate. The main new mathematical tool is a doubling inequality for solutions to fourth-order elliptic equations whose principal part P(x, D) is the product of two second-order elliptic operators P 1 (x, D), P 2 (x, D) such that P 1 (0, D) = P 2 (0, D). The proof of the doubling inequality is based on the Carleman method, a sharp three-spheres inequality and a bootstrapping argument. (paper)

Paleozoic age of high-pressure metamorphic rocks of the Dakh salient, North-Western Caucasus: results of U-Pb-geochronological study

International Nuclear Information System (INIS)

Somin, M.L.; Levchenkov, O.A.; Kotov, A.B.; Makeev, A.F.; Komarov, A.N.; Ro, N.I.; Lavrishchev, V.A.; Lebedev, V.A.

2007-01-01

U-Pb geochronological studies of an ancient component of the Dakh salient, i.e. metaaplites, which are vein fine-grained rocks made up by albite, microcline, quartz and potash mica, were made. Besides, K-Ar dating of granodiorites breaking through metamorphic rocks was conducted. U-Pb dating of accessory zircons (353 mln. years) defines the lower age boundary of the Dakh salient rock metamorphism. Its upper boundary was identified by K-Ar dating (301 ± 10 mln. years) of hornfels blende of nonmetamophized granodiorites [ru

2008 Gordon Research Conference on Rock Deformation

Energy Technology Data Exchange (ETDEWEB)

Hirth, James G.; Gray, Nancy Ryan

2009-09-21

The GRC on Rock Deformation highlights the latest research in brittle and ductile rock mechanics from experimental, field and theoretical perspectives. The conference promotes a multi-disciplinary forum for assessing our understanding of rock strength and related physical properties in the Earth. The theme for the 2008 conference is 'Real-time Rheology'. Using ever-improving geophysical techniques, our ability to constrain the rheological behavior during earthquakes and post-seismic creep has improved significantly. Such data are used to investigate the frictional behavior of faults, processes responsible for strain localization, the viscosity of the lower crust, and viscous coupling between the crust and mantle. Seismological data also provide information on the rheology of the lower crust and mantle through analysis of seismic attenuation and anisotropy. Geologists are improving our understanding of rheology by combining novel analyses of microstructures in naturally deformed rocks with petrologic data. This conference will bring together experts and students in these research areas with experimentalists and theoreticians studying the same processes. We will discuss and assess where agreement exists on rheological constraints derived at different length/time scales using different techniques - and where new insight is required. To encompass the elements of these topics, speakers and discussion leaders with backgrounds in geodesy, experimental rock deformation, structural geology, earthquake seismology, geodynamics, glaciology, materials science, and mineral physics will be invited to the conference. Thematic sessions will be organized on the dynamics of earthquake rupture, the rheology of the lower crust and coupling with the upper mantle, the measurement and interpretation of seismic attenuation and anisotropy, the dynamics of ice sheets and the coupling of reactive porous flow and brittle deformation for understanding geothermal and chemical

Seismic evidence of exhumed mantle rock basement at the Gorringe Bank and the adjacent Horseshoe and Tagus abyssal plains (SW Iberia)

Science.gov (United States)

Sallarès, Valentí; Martínez-Loriente, Sara; Prada, Manel; Gràcia, Eulàlia; Ranero, César; Gutscher, Marc-André; Bartolome, Rafael; Gailler, Audrey; Dañobeitia, Juan José; Zitellini, Nevio

2013-03-01

The Gorringe Bank is a gigantic seamount that separates the Horseshoe and Tagus abyssal plains offshore SW Iberia, in a zone that hosts the convergent boundary between the Africa and Eurasia plates. Although the region has been the focus of numerous investigations since the early 1970s, the lack of appropriate geophysical data makes the nature of the basement, and thus the origin of the structures, still debated. In this work, we present combined P-wave seismic velocity and gravity models along a transect that crosses the Gorringe Bank from the Tagus to the Horseshoe abyssal plains. The P-wave velocity structure of the basement is similar in the Tagus and Horseshoe plains. It shows a 2.5-3.0 km-thick top layer with a velocity gradient twice stronger than oceanic Layer 2 and an abrupt change to an underlying layer with a five-fold weaker gradient. Velocity and density is lower beneath the Gorringe Bank probably due to enhanced fracturing, that have led to rock disaggregation in the sediment-starved northern flank. In contrast to previous velocity models of this region, there is no evidence of a sharp crust-mantle boundary in any of the record sections. The modelling results indicate that the sediment overlays directly serpentinite rock, exhumed from the mantle with a degree of serpentinization decreasing from a maximum of 70-80% under the top of Gorringe Bank to less than 5% at a depth of ˜20 km. We propose that the three domains were originally part of a single serpentine rock band, of nature and possibly origin similar to the Iberia Abyssal Plain ocean-continent transition, which was probably generated during the earliest phase of the North Atlantic opening that followed continental crust breakup (Early Cretaceous). During the Miocene, the NW-SE trending Eurasia-Africa convergence resulted in thrusting of the southeastern segment of the exhumed serpentinite band over the northwestern one, forming the Gorringe Bank. The local deformation associated to plate

Fluids of the lower crust and upper mantle: deep is different

Science.gov (United States)

Manning, C. E.

2017-12-01

Deep fluids are important for the evolution and properties of the lower crust and upper mantle in tectonically active settings. Uncertainty about their chemistry has led past workers to use upper crustal fluids as analogues. However, recent results show that fluids at >15 km differ fundamentally from shallow fluids and help explain high-pressure metasomatism and resistivity patterns. Deep fluids are comprised of four components: H2O, non-polar gases (chiefly CO2), salts (mostly alkali chlorides), and rock-derived solutes (dominated by aluminosilicates and related components). The first three generally define the solvent properties of the fluid, and models must account for observations that H2O activity may be quite low. The contrasting behavior of H2O-gas and H2O-salt mixtures yields immiscibility in the ternary system, which can lead to separation of two phases with fundamentally different chemical and transport properties. Thermodynamic modeling of equilibrium between rocks and H2O using simple ionic species known from shallow-crustal systems yields solutions possessing total dissolved solids and ionic strength that are too low to be consistent with experiments and resistivity surveys. Addition of CO2 further lowers bulk solubility and conductivity. Therefore, additional species must be present in H2O, and H2O-salt solutions likely explain much of the evidence for fluid action in high-P settings. At low salinity, H2O-rich fluids are powerful solvents for aluminosilicate rock components that are dissolved as previously unrecognized polymerized clusters. Experiments show that, near H2O-saturated melting, Al-Si polymers comprise >80% of solutes. The stability of these species facilitates critical critical mixing in rock-H2O systems. Addition of salt (e.g., NaCl) changes solubility patterns, but aluminosilicate contents remain high. Thermodynamic models indicate that the ionic strength of fluids with Xsalt = 0.05 to 0.4 and equilibrated with model crustal rocks have

The SHRIMP zircon U-Pb dating of felsic volcanic rocks and its geological significance from yutian group in southern jiangxi

International Nuclear Information System (INIS)

Ji Chunyu; Wu Jianhua

2010-01-01

Past researches have showed that the Rb-Sr isochron ages of felsic end member for r hyolite-basalt b imodal volcanic rocks of Yutian Group in the Changpu and Longnan Basin in Southern Jiangxi Province are 175 ∼ 148 Ma, not only does its amplitude change more significantly, but it does not match with the Rb-Sr isochron ages (179 ∼ 173 Ma) of basic end member. As a result, I choose a method of zircon U-Pb dating with a higher accuracy, to obtain the rhyolite in the bottom of bimodal volcanic rocks in the Changpu Basin and the dacite in the top of of bimodal volcanic rocks in the Longnan Basin, whose zircon SHIRMP U-Pb age are respectively (195.2 ± 2.8) Ma and (191 ± 1.7) Ma. What's more, they are both almost the same in the error limit. It shows that the bimodal volcanic rocks in these both two basins are the product of the same session of magma movement. Simultaneously, it explains they form in a flash during the eruption intervals. According to the the newest International Stratigraphic Chart (Gradsrein et al. , 2004), in terms of geological age, the bimodal volcanic rocks in Changpu Basin and Longnan Basin, belonging to the early Early Jurassic. The zircon SHIRMP U-Pb age are distinctly older than the whole-rock Rb-Sr isochron age, it is probably because of the deviation of the dating method for the wholerock Rb-Sr isochron age. The zircon SHIRMP U-Pb age of bimodal volcanic rocks are 191 ∼ 195 Ma in Southern Jiangxi Province, which indicates that there had been an extensional environment. And after the bimodal volcanic activity, The zircon SHIRMP U-Pb age of felsic volcanic rocks are 145 ∼ 130 Ma. Both of the ages shows a as long as 45 Ma quiet period between 190 Ma and 145 Ma. It is unreasonable possible to interpreted by the single pattern of pacific plate subducting to eurasian plate. (authors)

Bragg transmission phase plates for the production of circularly polarized x-rays

International Nuclear Information System (INIS)

Lang, J.C.; Srajer, G.

1994-01-01

A thin-crystal Si (400) Bragg transmission x-ray phase plate has been constructed for the production of 5 to 12 keV circularly polarized x-rays. Using multiple beam diffraction from a GaAs crystal, a direct measurement of the degree of circular polarization as a function of off-Bragg position was made. These measurements indicated nearly complete circular polarization (|P c | ≥ 0.95) and full helicity reversal on opposite sides of the rocking curve

Pullback attractors for a singularly nonautonomous plate equation

Directory of Open Access Journals (Sweden)

Vera Lucia Carbone

2011-06-01

Full Text Available We consider the family of singularly nonautonomous plate equations with structural damping $$ u_{tt} + a(t,xu_t - Delta u_t + (-Delta^2 u + lambda u = f(u, $$ in a bounded domain $Omega subset mathbb{R}^n$, with Navier boundary conditions. When the nonlinearity f is dissipative we show that this problem is globally well posed in $H^2_0(Omega imes L^2(Omega$ and has a family of pullback attractors which is upper-semicontinuous under small perturbations of the damping a.

Upper mantle fluids evolution, diamond formation, and mantle metasomatism

Science.gov (United States)

Huang, F.; Sverjensky, D. A.

2017-12-01

During mantle metasomatism, fluid-rock interactions in the mantle modify wall-rock compositions. Previous studies usually either investigated mineral compositions in xenoliths and xenocrysts brought up by magmas, or examined fluid compositions preserved in fluid inclusions in diamonds. However, a key study of Panda diamonds analysed both mineral and fluid inclusions in the diamonds [1] which we used to develop a quantitative characterization of mantle metasomatic processes. In the present study, we used an extended Deep Earth Water model [2] to simulate fluid-rock interactions at upper mantle conditions, and examine the fluids and mineral assemblages together simultaneously. Three types of end-member fluids in the Panda diamond fluid inclusions include saline, rich in Na+K+Cl; silicic, rich in Si+Al; and carbonatitic, rich in Ca+Mg+Fe [1, 3]. We used the carbonatitic end-member to represent fluid from a subducting slab reacting with an excess of peridotite + some saline fluid in the host environment. During simultaneous fluid mixing and reaction with the host rock, the logfO2 increased by about 1.6 units, and the pH increased by 0.7 units. The final minerals were olivine, garnet and diamond. The Mg# of olivine decreased from 0.92 to 0.85. Garnet precipitated at an early stage, and its Mg# also decreased with reaction progress, in agreement with the solid inclusions in the Panda diamonds. Phlogopite precipitated as an intermediate mineral and then disappeared. The aqueous Ca, Mg, Fe, Si and Al concentrations all increased, while Na, K, and Cl concentrations decreased during the reaction, consistent with trends in the fluid inclusion compositions. Our study demonstrates that fluids coming from subducting slabs could trigger mantle metasomatism, influence the compositions of sub-lithospherc cratonic mantle, precipitate diamonds, and change the oxygen fugacity and pH of the upper mantle fluids. [1] Tomlinson et al. EPSL (2006); [2] Sverjensky, DA et al., GCA (2014

Large-surface-area diamond (111) crystal plates for applications in high-heat-load wavefront-preserving X-ray crystal optics.

Science.gov (United States)

Stoupin, Stanislav; Antipov, Sergey; Butler, James E; Kolyadin, Alexander V; Katrusha, Andrey

2016-09-01

Fabrication and results of high-resolution X-ray topography characterization of diamond single-crystal plates with large surface area (10 mm × 10 mm) and (111) crystal surface orientation for applications in high-heat-load X-ray crystal optics are reported. The plates were fabricated by laser-cutting of the (111) facets of diamond crystals grown using high-pressure high-temperature methods. The intrinsic crystal quality of a selected 3 mm × 7 mm crystal region of one of the studied samples was found to be suitable for applications in wavefront-preserving high-heat-load crystal optics. Wavefront characterization was performed using sequential X-ray diffraction topography in the pseudo plane wave configuration and data analysis using rocking-curve topography. The variations of the rocking-curve width and peak position measured with a spatial resolution of 13 µm × 13 µm over the selected region were found to be less than 1 µrad.

Transient thermal stresses in an orthotropic rectangular plate with convective heat transfer at upper and lower surfaces

International Nuclear Information System (INIS)

Sugano, Yoshihiro; Nakanishi, Takanori; Ito, Masahiko; Saito, Koichi.

1982-01-01

Recently, anisotropic materials have been used widely for reactor core elements and fast flying objects, therefore, the problem of thermal stress in anisotropic bodies has been studied actively. In this study, the unsteady plane thermal stress in an orthotropic rectangular thin plate heated by the temperature of ambient medium was analyzed, taking the heat transfer on both surfaces into account. The influence that the anisotropy of material constants and the heat transfer on both surfaces exert on the temperature and thermal stress of the plate was examined. Moreover, in order to investigate into the effect of the aspect ratio of the plate on the temperature and thermal stress, the unsteady distributions of temperature and thermal stress in an orthotropic semi-infinite band, of which the end surfaces are heated by ambient medium, were analyzed. The numerical calculation was carried out, and the results are shown. Before, it was difficult to satisfy the boundary condition related to shearing stress, accordingly, the analysis has not been performed, but in this study, it was shown that the analysis is possible. (Kako, I.)

Active unicameral bone cysts in the upper limb are at greater risk of fracture.

Science.gov (United States)

Tey, Inn Kuang; Mahadev, Arjandas; Lim, Kevin Boon Leong; Lee, Eng Hin; Nathan, Saminathan Suresh

2009-08-01

To elucidate the natural history of unicameral bone cyst (UBC) and risk factors for pathological fracture. 14 males and 8 females (mean age, 9 years) diagnosed with UBC were reviewed. Cyst location, symptoms, and whether there was any fracture or surgery were recorded. Cyst parameters were measured on radiographs, and included (1) the cyst index, (2) the ratio of the widest cyst diameter to the growth plate diameter, and (3) the adjusted distance of the cyst border from the growth plate. There were 11 upper- and 11 lower-limb cysts. 13 patients had pathological fractures and 9 did not. 20 patients were treated conservatively with limb immobilisation; 2 underwent curettage and bone grafting (one resolved and one did not). Seven cysts resolved (5 had fractures and 2 did not). The risk of fracture was higher in the upper than lower limbs (100% vs 18%, pFractured cysts were larger than unfractured cysts (mean cyst index, 4.5 vs. 2.2, p=0.07). Active cysts were more likely to fracture. Conservative management had a 30% resolution rate. Surgery should be considered for large active cysts in the upper limbs in order to minimise the fracture risk.

Convective heat transfer of supercritical CO_2 in a rock fracture for enhanced geothermal systems

International Nuclear Information System (INIS)

Zhang, Le; Jiang, Peixue; Wang, Zhenchuan; Xu, Ruina

2017-01-01

Highlights: • Contrasting experiments between a rough and a smooth fracture were performed. • A numerical model of rough fracture was reconstructed based on CT scanning data. • Heat transfer in rough fracture was affected by channeling and disturbance effects. - Abstract: Convective heat transfer characteristics of supercritical pressure fluid in a rock fracture are important for building an accurate heat transfer model of enhanced geothermal systems. This paper presents experimental investigations of laminar convection heat transfer of supercritical pressure CO_2 in an artificial smooth parallel-plate fracture and a rough and tortuous fracture that was created using the Brazilian technique. Hot rock with a relatively high initial temperature reserves more heat, which can ensure a larger heat extraction rate for a longer time when cold fluid flows through the fracture. Compared with the smooth parallel-plate fracture, CO_2 flowing through the rough and tortuous fracture with an equivalent hydraulic aperture extracted less heat from the hot rock due to the less efficient heat exchange in a rough fracture caused by channeling effect. This was illustrated by numerical simulation results of the reconstructed fracture based on micro-computed tomography scan data. The overall Nusselt number obtained from the numerical results was larger in a rough fracture with a larger Reynolds number due to disturbance effect on the boundary layer development. The heat transfer performance in a rough fracture is therefore influenced by interactions of the channeling and disturbance effects caused by the tortuous flow path.

Trace-element geochemistry of metabasaltic rocks from the Yukon-Tanana Upland and implications for the origin of tectonic assemblages in east-central Alaska

Science.gov (United States)

Dusel-Bacon, C.; Cooper, K.M.

1999-01-01

We present major- and trace- element geochemical data for 27 amphibolites and six greenstones from three structural packages in the Yukon-Tanana Upland of east-central Alaska: the Lake George assemblage (LG) of Devono-Mississippian augen gneiss, quartz-mica schist, quartzite, and amphibolite; the Taylor Mountain assemblage (TM) of mafic schist and gneiss, marble, quartzite, and metachert; and the Seventymile terrane of greenstone, serpentinized peridotite, and Mississippian to Late Triassic metasedimentary rocks. Most LG amphibolites have relatively high Nb, TiO2, Zr, and light rare earth element contents, indicative of an alkalic to tholeiitic, within-plate basalt origin. The within-plate affinities of the LG amphibolites suggest that their basaltic parent magmas developed in an extensional setting and support a correlation of these metamorphosed continental-margin rocks with less metamorphosed counterparts across the Tintina fault in the Selwyn Basin of the Canadian Cordillera. TM amphibolites have a tholeiitic or calc-alkalic composition, low normalized abundances of Nb and Ta relative to Th and La, and Ti/V values of the proximity of the arc and marginal basin to continental crust. The arc geochemistry of TM amphibolites is consistent with a model in which the TM assemblage includes arc rocks generated above a west-dipping subduction zone outboard of the North American continental margin in mid-Paleozoic through Triassic time. The ocean-floor or within-plate basalt geochemistry of the Seventymile greenstones supports the correlation of the Seventymile terrane with the Slide Mountain terrane in Canada and the hypothesis that these oceanic rocks originated in a basin between the continental margin and an arc to the west.

What was the Paleogene latitude of the Lhasa terrane? A reassessment of the geochronology and paleomagnetism of Linzizong volcanic rocks (Linzhou basin, Tibet)

Science.gov (United States)

Huang, Wentao; Dupont-Nivet, Guillaume; Lippert, Peter C.; van Hinsbergen, Douwe J. J.; Dekkers, Mark J.; Waldrip, Ross; Ganerød, Morgan; Li, Xiaochun; Guo, Zhaojie; Kapp, Paul

2015-03-01

The Paleogene latitude of the Lhasa terrane (southern Tibet) can constrain the age of the onset of the India-Asia collision. Estimates for this latitude, however, vary from 5°N to 30°N, and thus, here, we reassess the geochronology and paleomagnetism of Paleogene volcanic rocks from the Linzizong Group in the Linzhou basin. The lower and upper parts of the section previously yielded particularly conflicting ages and paleolatitudes. We report consistent 40Ar/39Ar and U-Pb zircon dates of 52 Ma for the upper Linzizong, and 40Ar/39Ar dates ( 51 Ma) from the lower Linzizong are significantly younger than U-Pb zircon dates (64-63 Ma), suggesting that the lower Linzizong was thermally and/or chemically reset. Paleomagnetic results from 24 sites in lower Linzizong confirm a low apparent paleolatitude of 5°N, compared to the upper part ( 20°N) and to underlying Cretaceous strata ( 20°N). Detailed rock magnetic analyses, end-member modeling of magnetic components, and petrography from the lower and upper Linzizong indicate widespread secondary hematite in the lower Linzizong, whereas hematite is rare in upper Linzizong. Volcanic rocks of the lower Linzizong have been hydrothermally chemically remagnetized, whereas the upper Linzizong retains a primary remanence. We suggest that remagnetization was induced by acquisition of chemical and thermoviscous remanent magnetizations such that the shallow inclinations are an artifact of a tilt correction applied to a secondary remanence in lower Linzizong. We estimate that the Paleogene latitude of Lhasa terrane was 20 ± 4°N, consistent with previous results suggesting that India-Asia collision likely took place by 52 Ma at 20°N.

Theoretical investigation of interaction between a rectangular plate and fractional viscoelastic foundation

Directory of Open Access Journals (Sweden)

Chengcheng Zhang

2014-08-01

Full Text Available The interaction between plates and foundations is a typical problem encountered in geotechnical engineering. The long-term plate performance is highly dependent on the rheological characteristics of ground soil. Compared with conventional linear rheology, the fractional calculus-based theory is a more powerful mathematical tool that can address this issue. This paper proposes a fractional Merchant model (FMM to investigate the time-dependent behavior of a simply supported rectangular plate on viscoelastic foundation. The correspondence principle involving Laplace transforms was employed to derive the closed-form solutions of plate response under uniformly distributed load. The plate deflection, bending moment, and foundation reaction calculated using the FMM were compared with the results obtained from the analogous elastic model (EM and the standard Merchant model (SMM. It is shown that the upper and lower bound solutions of the FMM can be determined using the EM. In addition, a parametric study was performed to examine the influences of the model parameters on the time-dependent behavior of the plate–foundation interaction problem. The results indicate that a small fractional differential order corresponds to a plate resting on a sandy soil foundation, while the fractional differential order value should be increased for a clayey soil foundation. The long-term performance of a foundation plate can be accurately simulated by varying the values of the fractional differential order and the viscosity coefficient. The observations from this study reveal that the proposed fractional model has the capability to capture the variation of plate deflection over many decades of time.

Upper Cretaceous molluscan record along a transect from Virden, New Mexico, to Del Rio, Texas

Science.gov (United States)

Cobban, W.A.; Hook, S.C.; McKinney, K.C.

2008-01-01

Updated age assignments and new collections of molluscan fossils from lower Cenomanian through upper Campanian strata in Texas permit a much refined biostratigraphic correlation with the rocks of New Mexico and the Western Interior. Generic names of many Late Cretaceous ammonites and inoceramid bivalves from Texas are updated to permit this correlation. Strata correlated in the west-to-east transect include the lower Cenomanian Beartooth Quartzite and Sarten Sandstone of southwest New Mexico, and the Eagle Mountains Formation, Del Rio Clay, Buda Limestone, and. basal beds of the Chispa Summit, Ojinaga, and Boquillas Formations of the Texas-Mexico border area. Middle Cenomanian strata are lacking in southwestern New Mexico but are present in the lower parts of the Chispa Summit and Boquillas Formations in southwest Texas. Upper Cenomanian and lower Turonian rocks are present at many localities in New Mexico and Texas in the Mancos Shale and Chispa Summit, Ojinaga, and Boquillas Formations. Middle Turonian and younger rocks seem to be entirely nonmarine in southwestern New Mexico, but they are marine in the Rio Grande area in the Chispa. Summit, Ojinaga, and Boquillas Formations. The upper part of the Chispa Summit and Boquillas contain late Turonian fossils. Rocks of Coniacian and Santonian age are present high in the Chispa Summit, Ojinaga, and Boquillas Formations, and in the lower part of the Austin. The San Carlos, Aguja, Pen, and Austin Formations contain fossils of Campanian age. Fossils representing at least 38 Upper Cretaceous ammonite zones are present along the transect. Collections made in recent years in southwestern New Mexico and at Sierra de Cristo Rey just west of downtown El Paso, Texas, have been well treated and do not need revision. Taxonomic names and zonations published in the pre-1970 literature on the Rio Grande area of Texas have been updated. New fossil collections from the Big Bend National Park, Texas, allow for a much refined correlation

Geohydrologic reconnaissance of the upper Potomac River basin

Science.gov (United States)

Trainer, Frank W.; Watkins, Frank A.

1975-01-01

The upper Potomac River basin, in the central Appalachian region in Pennsylvania, Maryland, Virginia, and West Virginia, is a humid temperate region of diverse fractured rocks. Three geohydrologic terranes, which underlie large parts of the basin, are described in terms of their aquifer characteristics and of the magnitude and duration of their base runoff: (1) fractured rock having a thin regolith, (2) fractured rock having a thick regolith, and (3) carbonate rock. Crystalline rock in the mountainous part of the Blue Ridge province and shale with tight sandstone in the folded Appalachians are covered with thin regolith. Water is stored in and moves through fairly unmodified fractures. Average transmissivity (T) is estimated to be 150 feet squared per day, and average storage coefficient (S), 0.005. Base runoff declines rapidly from its high levels during spring and is poorly sustained during the summer season of high evapotranspiration. The rocks in this geohydrologic terrane are the least effective in the basin for the development of water supplies and as a source of dry-weather streamflow. Crystalline and sedimentary rocks in the Piedmont province and in the lowland part of the Blue Ridge province are covered with thick regolith. Water is stored in and moves through both the regolith and the underlying fractured rock. Estimated average values for aquifer characteristics are T, 200 feet squared per day, and S, 0.01. Base runoff is better sustained in this terrane than in the thin-regolith terrane and on the average .is about twice as great. Carbonate rock, in which fractures have been widened selectively by solution, especially near streams, has estimated average aquifer characteristics of T, 500 feet squared per day, and S, 0.03-0.04. This rock is the most effective in the basin in terms of water supply and base runoff. Where its fractures have not been widened by solution, the carbonate rock is a fractured-rock aquifer much like the noncarbonate rock. At low

Lower Cretaceous Source Rock and its Implication for the Gulf of Guinea Petroleum System

International Nuclear Information System (INIS)

Frost, B.R.; Griffith, R.C.

2002-01-01

Current petroleum system models for the Gulf of Guinea propose Tertiary-age deltaic organic material as the principal source for the hydrocarbons found there. Although previous workers recognized numerous difficulties and inconsistencies, no alternative model has been resented to adequately explain the complete petroleum system. We propose that the principal source rock for the Gulf of Guinea system occurs in upper lower Cretaceous-age shales at the rift-drift transition. Tertiary loading and the consequent maturation of this lower Cretaceous source rock can explain the controls on tap formation, reservoir distribution and hydrocarbon types found in the Gulf of Guinea

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Spirit's View Beside 'Home Plate' on Sol 1823 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11971 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11971 NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this stereo, 180-degree view of the rover's surroundings during the 1,823rd Martian day, or sol, of Spirit's surface mission (Feb. 17, 2009). This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. The center of the view is toward the south-southwest. The rover had driven 7 meters (23 feet) eastward earlier on Sol 1823, part of maneuvering to get Spirit into a favorable position for climbing onto the low plateau called 'Home Plate.' However, after two driving attempts with negligible progress during the following three sols, the rover team changed its strategy for getting to destinations south of Home Plate. The team decided to drive Spirit at least partway around Home Plate, instead of ascending the northern edge and taking a shorter route across the top of the plateau. Layered rocks forming part of the northern edge of Home Plate can be seen near the center of the image. Rover wheel tracks are visible at the lower edge. This view is presented as a cylindrical-perspective projection with geometric seam correction.

Measurement of two-phase flow at the core upper plenum interface under simulated reflood conditions

International Nuclear Information System (INIS)

Thomas, D.G.; Combs, S.K.; Bagwell, M.E.

1980-01-01

Objectives of the Instrument Development Loop program were to simulate flows at the core/upper plenum interface during the reflood phase of a LOCA and to develop instruments for measuring mass-flows at this interface. A tie plate drag body was developed and tested successfully, and the data obtained were shown to be equivalent to pressure drops. The tie-plate drag body gave useful measurements in pure downflow, and the drag/turbine combination correlates with mass flow for high upflow

Cold plate

Energy Technology Data Exchange (ETDEWEB)

Marroquin, Christopher M.; O' Connell, Kevin M.; Schultz, Mark D.; Tian, Shurong

2018-02-13

A cold plate, an electronic assembly including a cold plate, and a method for forming a cold plate are provided. The cold plate includes an interface plate and an opposing plate that form a plenum. The cold plate includes a plurality of active areas arranged for alignment over respective heat generating portions of an electronic assembly, and non-active areas between the active areas. A cooling fluid flows through the plenum. The plenum, at the non-active areas, has a reduced width and/or reduced height relative to the plenum at the active areas. The reduced width and/or height of the plenum, and exterior dimensions of cold plate, at the non-active areas allow the non-active areas to flex to accommodate surface variations of the electronics assembly. The reduced width and/or height non-active areas can be specifically shaped to fit between physical features of the electronics assembly.

Lateral variations in upper-mantle seismic anisotropy in the Pacific from inversion of a surface-wave dispersion dataset

Science.gov (United States)

Eddy, C. L.; Ekstrom, G.; Nettles, M.; Gaherty, J. B.

2017-12-01

We present a three-dimensional model of the anisotropic velocity structure of the Pacific lithosphere and asthenosphere. The presence of seismic anisotropy in the oceanic upper mantle provides information about the geometry of flow in the mantle, the nature of the lithosphere-asthenosphere boundary, and the possible presence of partial melt in the asthenosphere. Our dataset consists of fundamental-mode dispersion for Rayleigh and Love waves measured between 25-250 s with paths crossing the Pacific Ocean. We invert the phase anomaly measurements directly for three-dimensional anisotropic velocity structure. Our models are radially anisotropic and include the full set of elastic parameters that describe azimuthal variations in velocity (e.g. Gc, Gs). We investigate the age dependence of seismic velocity and radial anisotropy and find that there are significant deviations from the velocities predicted by a simple oceanic plate cooling model. We observe strong radial anisotropy with vsh > vsv in the asthenosphere of the central Pacific. We investigate the radial anisotropy in the shallow lithosphere, where previous models have reported conflicting results. There is a contrast in both upper-mantle isotropic velocities and radial anisotropy between the Pacific and Nazca plates, across the East Pacific Rise. We also investigate lateral variations in azimuthal anisotropy throughout the Pacific upper mantle and find that there are large areas over which the anisotropy fast axis does not align with absolute plate motion, suggesting the presence of small-scale convection or pressure-driven flow beneath the base of the oceanic plate.

'Escher' Rock

Science.gov (United States)

2004-01-01

[figure removed for brevity, see original site] Chemical Changes in 'Endurance' Rocks [figure removed for brevity, see original site] Figure 1 This false-color image taken by NASA's Mars Exploration Rover Opportunity shows a rock dubbed 'Escher' on the southwestern slopes of 'Endurance Crater.' Scientists believe the rock's fractures, which divide the surface into polygons, may have been formed by one of several processes. They may have been caused by the impact that created Endurance Crater, or they might have arisen when water leftover from the rock's formation dried up. A third possibility is that much later, after the rock was formed, and after the crater was created, the rock became wet once again, then dried up and developed cracks. Opportunity has spent the last 14 sols investigating Escher, specifically the target dubbed 'Kirchner,' and other similar rocks with its scientific instruments. This image was taken on sol 208 (Aug. 24, 2004) by the rover's panoramic camera, using the 750-, 530- and 430-nanometer filters. The graph above shows that rocks located deeper into 'Endurance Crater' are chemically altered to a greater degree than rocks located higher up. This chemical alteration is believed to result from exposure to water. Specifically, the graph compares ratios of chemicals between the deep rock dubbed 'Escher,' and the more shallow rock called 'Virginia,' before (red and blue lines) and after (green line) the Mars Exploration Rover Opportunity drilled into the rocks. As the red and blue lines indicate, Escher's levels of chlorine relative to Virginia's went up, and sulfur down, before the rover dug a hole into the rocks. This implies that the surface of Escher has been chemically altered to a greater extent than the surface of Virginia. Scientists are still investigating the role water played in influencing this trend. These data were taken by the rover's alpha particle X-ray spectrometer.

Observations at convergent margins concerning sediment subduction, subduction erosion, and the growth of continental crust

Science.gov (United States)

von Huene, Roland E.; Scholl, D. W.

1991-01-01

At ocean margins where two plates converge, the oceanic plate sinks or is subducted beneath an upper one topped by a layer of terrestrial crust. This crust is constructed of continental or island arc material. The subduction process either builds juvenile masses of terrestrial crust through arc volcanism or new areas of crust through the piling up of accretionary masses (prisms) of sedimentary deposits and fragments of thicker crustal bodies scraped off the subducting lower plate. At convergent margins, terrestrial material can also bypass the accretionary prism as a result of sediment subduction, and terrestrial matter can be removed from the upper plate by processes of subduction erosion. Sediment subduction occurs where sediment remains attached to the subducting oceanic plate and underthrusts the seaward position of the upper plate's resistive buttress (backstop) of consolidated sediment and rock. Sediment subduction occurs at two types of convergent margins: type 1 margins where accretionary prisms form and type 2 margins where little net accretion takes place. At type 2 margins (???19,000 km in global length), effectively all incoming sediment is subducted beneath the massif of basement or framework rocks forming the landward trench slope. At accreting or type 1 margins, sediment subduction begins at the seaward position of an active buttress of consolidated accretionary material that accumulated in front of a starting or core buttress of framework rocks. Where small-to-mediumsized prisms have formed (???16,300 km), approximately 20% of the incoming sediment is skimmed off a detachment surface or decollement and frontally accreted to the active buttress. The remaining 80% subducts beneath the buttress and may either underplate older parts of the frontal body or bypass the prism entirely and underthrust the leading edge of the margin's rock framework. At margins bordered by large prisms (???8,200 km), roughly 70% of the incoming trench floor section is

The Juchatengo complex: an upper-level ophiolite assemblage of late Paleozoic age in Oaxaca, southern Mexico

Science.gov (United States)

Grajales-Nishimura, José Manuel; Ramos-Arias, Mario Alfredo; Solari, Luigi; Murillo-Muñetón, Gustavo; Centeno-García, Elena; Schaaf, Peter; Torres-Vargas, Ricardo

2018-04-01

The Juchatengo complex (JC) suite is located between the Proterozoic Oaxacan complex to the north and the Xolapa complex to the south, and was amalgamated by late Paleozoic magmatism. It consists of mafic and sedimentary rocks that have oceanic affinities, with internal pseudostratigraphic, structural and metamorphic characteristics, which resemble a typical upper-level ophiolite assemblage. New U-Pb zircon and previous hornblende K-Ar analyses yield ages of ca. 291-313 Ma (U-Pb) for plagiogranites and ca. 282-277 Ma for tonalites intruding the entire sequence, including pelagic sediments at the top, with a maximum deposition age of ca. 278 Ma and noteworthy local provenance. These data constrain the age of the JC to the Late Pennsylvanian-Early Permian period. Hf isotopic analyses obtained from zircons in the JC plagiogranite and tonalite show that they come from a similar primitive mantle source (176Hf/177Hf: 0.282539-0.283091; ƐHf(t): + 3.2 to + 15.0). ƐHf(t) values from near 0 to - 2.8 in the tonalites indicate a contribution from the continental crust. Trace elements and REE patterns in whole rock and zircons point to a primitive mantle source for differentiated mafic, plagiogranite dykes and tonalitic plutons. Geochronological and geochemical data address the generation of new oceanic crust above the subduction zone, probably in a backarc setting. In this tectonic scenario, the JC ophiolite originated due to the convergence of the paleo-Pacific plate below the already integrated Oaxacan and Acatlán complexes in western Pangea. The dextral displacement places the deformation in a transtensional regime during the late Paleozoic age.

Re-appraisal of the Santa Rita Greenstone Belt stratigraphy, central Brazil, based on new U-Pb SHRIMP age and Sm-Nd data of felsic metavolcanic rocks

International Nuclear Information System (INIS)

Pimentel, Marcio Martins; Jost, Hardy; Fuck, Reinhardt Adolfo; Junges, Sergio Luiz; Armstrong, Richard; Resende, Marcelo Goncalves

2000-01-01

The Santa Rita greenstone belt represents one of the supracrustal belts of the Archaen terranes of Goias, central Brazil. The stratigraphic sequence of this greenstone belt comprises a lower of komatities and basalts and an upper metasedimentary unit made of carbonaceous schits, chert, iron formation and marble, unconformably overlain by clastic metasedimentary rocks. Felsic metavolcanics occur at the interface between the metabasalts and the upper metasedimentary pile. U-Pb SHRIMP age for zircons from the felsic metavolcanics reveal that it is not part of the Archaean sequence, but represents the product of mesoproterozoic (1580 ± 12 Ma) magmatic event. Sm-Nd isotopic data (initial e CHUR values between -10.5 and -14.9) and T DM values of 3.0 and 3.2 Ga, within the range of the surrounding TTG terranes, indicate that the original felsic magmas were produced by re-melting of Archaen crust. The data demonstrate that the Goias greenstone belt contains infolded and imbricated proterozoic rocks, as previously suggested by Sm-Nd isotopic analyses of some of the upper detrital metasedimentary rocks. (author)

Re-appraisal of the Santa Rita Greenstone Belt stratigraphy, central Brazil, based on new U-Pb SHRIMP age and Sm-Nd data of felsic metavolcanic rocks

Energy Technology Data Exchange (ETDEWEB)

Pimentel, Marcio Martins; Jost, Hardy; Fuck, Reinhardt Adolfo; Junges, Sergio Luiz [Brasilia Univ., DF (Brazil). Inst. de Geociencias]. E-mail: marcio@unb.br; Armstrong, Richard [Australian National Univ., Canberra, ACT (Australia). Research School of Earth Sciences; Resende, Marcelo Goncalves [Universidade Catolica de Brasilia, DF (Brazil). Curso de Graduacao em Engenharia Ambiental

2000-03-01

The Santa Rita greenstone belt represents one of the supracrustal belts of the Archaen terranes of Goias, central Brazil. The stratigraphic sequence of this greenstone belt comprises a lower of komatities and basalts and an upper metasedimentary unit made of carbonaceous schits, chert, iron formation and marble, unconformably overlain by clastic metasedimentary rocks. Felsic metavolcanics occur at the interface between the metabasalts and the upper metasedimentary pile. U-Pb SHRIMP age for zircons from the felsic metavolcanics reveal that it is not part of the Archaean sequence, but represents the product of mesoproterozoic (1580 {+-} 12 Ma) magmatic event. Sm-Nd isotopic data (initial e{sub CHUR} values between -10.5 and -14.9) and T{sub DM} values of 3.0 and 3.2 Ga, within the range of the surrounding TTG terranes, indicate that the original felsic magmas were produced by re-melting of Archaen crust. The data demonstrate that the Goias greenstone belt contains infolded and imbricated proterozoic rocks, as previously suggested by Sm-Nd isotopic analyses of some of the upper detrital metasedimentary rocks. (author)

Direct observations of rock moisture, a hidden component of the hydrologic cycle

Science.gov (United States)

Rempe, Daniella M.; Dietrich, William E.

2018-03-01

Recent theory and field observations suggest that a systematically varying weathering zone, that can be tens of meters thick, commonly develops in the bedrock underlying hillslopes. Weathering turns otherwise poorly conductive bedrock into a dynamic water storage reservoir. Infiltrating precipitation typically will pass through unsaturated weathered bedrock before reaching groundwater and running off to streams. This invisible and difficult to access unsaturated zone is virtually unexplored compared with the surface soil mantle. We have proposed the term “rock moisture” to describe the exchangeable water stored in the unsaturated zone in weathered bedrock, purposely choosing a term parallel to, but distinct from, soil moisture, because weathered bedrock is a distinctly different material that is distributed across landscapes independently of soil thickness. Here, we report a multiyear intensive campaign of quantifying rock moisture across a hillslope underlain by a thick weathered bedrock zone using repeat neutron probe measurements in a suite of boreholes. Rock moisture storage accumulates in the wet season, reaches a characteristic upper value, and rapidly passes any additional rainfall downward to groundwater. Hence, rock moisture storage mediates the initiation and magnitude of recharge and runoff. In the dry season, rock moisture storage is gradually depleted by trees for transpiration, leading to a common lower value at the end of the dry season. Up to 27% of the annual rainfall is seasonally stored as rock moisture. Significant rock moisture storage is likely common, and yet it is missing from hydrologic and land-surface models used to predict regional and global climate.

Direct observations of rock moisture, a hidden component of the hydrologic cycle.

Science.gov (United States)

Rempe, Daniella M; Dietrich, William E

2018-03-13

Recent theory and field observations suggest that a systematically varying weathering zone, that can be tens of meters thick, commonly develops in the bedrock underlying hillslopes. Weathering turns otherwise poorly conductive bedrock into a dynamic water storage reservoir. Infiltrating precipitation typically will pass through unsaturated weathered bedrock before reaching groundwater and running off to streams. This invisible and difficult to access unsaturated zone is virtually unexplored compared with the surface soil mantle. We have proposed the term "rock moisture" to describe the exchangeable water stored in the unsaturated zone in weathered bedrock, purposely choosing a term parallel to, but distinct from, soil moisture, because weathered bedrock is a distinctly different material that is distributed across landscapes independently of soil thickness. Here, we report a multiyear intensive campaign of quantifying rock moisture across a hillslope underlain by a thick weathered bedrock zone using repeat neutron probe measurements in a suite of boreholes. Rock moisture storage accumulates in the wet season, reaches a characteristic upper value, and rapidly passes any additional rainfall downward to groundwater. Hence, rock moisture storage mediates the initiation and magnitude of recharge and runoff. In the dry season, rock moisture storage is gradually depleted by trees for transpiration, leading to a common lower value at the end of the dry season. Up to 27% of the annual rainfall is seasonally stored as rock moisture. Significant rock moisture storage is likely common, and yet it is missing from hydrologic and land-surface models used to predict regional and global climate.

Sulphide mineralization and wall-rock alteration in ophiolites and modern oceanic spreading centres

Science.gov (United States)

Koski, R.A.

1983-01-01

Massive and stockwork Fe-Cu-Zn (Cyprus type) sulphide deposits in the upper parts of ophiolite complexes represent hydrothermal mineralization at ancient accretionary plate boundaries. These deposits are probable metallogenic analogues of the polymetallic sulphide deposits recently discovered along modern oceanic spreading centres. Genetic models for these deposits suggest that mineralization results from large-scale circulation of sea-water through basaltic basement along the tectonically active axis of spreading, a zone of high heat flow. The high geothermal gradient above 1 to 2 km deep magma chambers emplaced below the ridge axis drives the convective circulation cell. Cold oxidizing sea-water penetrating the crust on the ridge flanks becomes heated and evolves into a highly reduced somewhat acidic hydrothermal solvent during interaction with basaltic wall-rock. Depending on the temperature and water/rock ratio, this fluid is capable of leaching and transporting iron, manganese, and base metals; dissolved sea-water sulphate is reduced to sulphide. At the ridge axis, the buoyant hydrothermal fluid rises through permeable wall-rocks, and fluid flow may be focussed along deep-seated fractures related to extensional tectonic processes. Metal sulphides are precipitated along channelways as the ascending fluid undergoes adiabatic expansion and then further cooling during mixing with ambient sub-sea-floor water. Vigorous fluid flow results in venting of reduced fluid at the sea-floor/sea-water interface and deposition of massive sulphide. A comparison of sulphide mineralization and wall-rock alteration in ancient and modern spreading centre environments supports this genetic concept. Massive sulphide deposits in ophiolites generally occur in clusters of closely spaced (stacked sequences of pillow basalt and sheet flows, the sea-floor underlying numerous deposits in Guaymas Basin consists of diatomaceous ooze and terrigenous clastic sediment that is intruded by diabase

Rock fragmentation

Energy Technology Data Exchange (ETDEWEB)

Brown, W.S.; Green, S.J.; Hakala, W.W.; Hustrulid, W.A.; Maurer, W.C. (eds.)

1976-01-01

Experts in rock mechanics, mining, excavation, drilling, tunneling and use of underground space met to discuss the relative merits of a wide variety of rock fragmentation schemes. Information is presented on novel rock fracturing techniques; tunneling using electron beams, thermocorer, electric spark drills, water jets, and diamond drills; and rock fracturing research needs for mining and underground construction. (LCL)

The Evolution of Eastern Himalayan Syntaxis of Tibetan Plateau

Science.gov (United States)

Zhang, S.; Wu, T.; Li, M.; Zhang, Y.; Hua, Y.; Zhang, B.

2017-12-01

Indian plate has been colliding with Eurasian plate since 50Ma years ago, resulting in the Tethys extinction, crust shortening and Tibetan plateau uplift. But it is still a debate how the Tibetan Plateau material escaped. This study tries to invert the distributions of dispersion phase velocity and anisotropy in Eastern Himalayan Syntaxis (EHS) based on the seismic data. We focused on the seven sub-blocks around EHS region. Sub-block "EHS" represents EHS corner with high velocity anomalies, significantly compressed in the axle and strike directions. Sub-blocks "LSD", "QTB" and "SP-GZB" are located at its northern areas with compressions also, and connected with low-velocity anomalies in both crustal and upper mantle rocks. Sub-block "ICB" is located at its southern area with low velocity anomaly, and connected with Tengchong volcano. Sub-blocks "SYDB" and "YZB" are located at its eastern areas with high velocity anomalies in both crustal and upper mantle rocks. Our results demonstrated that significant azimuthal anisotropy of crust (t£30s) and upper mantle (30s£t£60s). Crustal anisotropy indicates the orogenic belt matched well with the direction of fast propagation, and upper mantle anisotropy represents the lattic-preferred orientation (LPO) of mantle minerals (e.g. olivine and basalt), indicating the features of subducting Indian plate. Besides, Red River fault is a dextral strike fault, controlling the crustal and mantle migration. There is a narrow zone to be the channel flow of Tibetan crustal materials escaping toward Yunnan area. The evolution of EHS seems constrained by gravity isostatic mechanism. Keywords: Tibetan Plateau; Eastern Himalayan Syntaxis; Red River fault; crustal flow; surface wave; anisotropy

Old model Nd ages in Namibian Pan-African rocks

International Nuclear Information System (INIS)

Hawkesworth, C.J.; Kramers, J.D.

1981-01-01

The Nd-isotope analytical technique has been used to study the Damara high-temperature belt of Namibia formed during the widespread orogenic event categorized as Pan African. The results are presented of an investigation by Nd and Sr isotopes of the range in age and geochemical characteristics of rock sequences and provinces within both the upper mantle and the pre-existing crust which were sampled during the orogeny, and hence provided the major components of what is now a stable segment of continental crust. (U.K.)

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Elastic Rock Heterogeneity Controls Brittle Rock Failure during Hydraulic Fracturing

Science.gov (United States)

Langenbruch, C.; Shapiro, S. A.

2014-12-01

For interpretation and inversion of microseismic data it is important to understand, which properties of the reservoir rock control the occurrence probability of brittle rock failure and associated seismicity during hydraulic stimulation. This is especially important, when inverting for key properties like permeability and fracture conductivity. Although it became accepted that seismic events are triggered by fluid flow and the resulting perturbation of the stress field in the reservoir rock, the magnitude of stress perturbations, capable of triggering failure in rocks, can be highly variable. The controlling physical mechanism of this variability is still under discussion. We compare the occurrence of microseismic events at the Cotton Valley gas field to elastic rock heterogeneity, obtained from measurements along the treatment wells. The heterogeneity is characterized by scale invariant fluctuations of elastic properties. We observe that the elastic heterogeneity of the rock formation controls the occurrence of brittle failure. In particular, we find that the density of events is increasing with the Brittleness Index (BI) of the rock, which is defined as a combination of Young's modulus and Poisson's ratio. We evaluate the physical meaning of the BI. By applying geomechanical investigations we characterize the influence of fluctuating elastic properties in rocks on the probability of brittle rock failure. Our analysis is based on the computation of stress fluctuations caused by elastic heterogeneity of rocks. We find that elastic rock heterogeneity causes stress fluctuations of significant magnitude. Moreover, the stress changes necessary to open and reactivate fractures in rocks are strongly related to fluctuations of elastic moduli. Our analysis gives a physical explanation to the observed relation between elastic heterogeneity of the rock formation and the occurrence of brittle failure during hydraulic reservoir stimulations. A crucial factor for understanding

Rock.XML - Towards a library of rock physics models

Science.gov (United States)

Jensen, Erling Hugo; Hauge, Ragnar; Ulvmoen, Marit; Johansen, Tor Arne; Drottning, Åsmund

2016-08-01

Rock physics modelling provides tools for correlating physical properties of rocks and their constituents to the geophysical observations we measure on a larger scale. Many different theoretical and empirical models exist, to cover the range of different types of rocks. However, upon reviewing these, we see that they are all built around a few main concepts. Based on this observation, we propose a format for digitally storing the specifications for rock physics models which we have named Rock.XML. It does not only contain data about the various constituents, but also the theories and how they are used to combine these building blocks to make a representative model for a particular rock. The format is based on the Extensible Markup Language XML, making it flexible enough to handle complex models as well as scalable towards extending it with new theories and models. This technology has great advantages as far as documenting and exchanging models in an unambiguous way between people and between software. Rock.XML can become a platform for creating a library of rock physics models; making them more accessible to everyone.

A solution for the Graetz problem in parallel plates, with axial heat conduction in the fluid and in the wall

International Nuclear Information System (INIS)

Biage, M.

1983-04-01

A heat transfer problem in parallel plates with infinite with has been solved, with axial heat conduction in the fluid and in the wall, considering steady-state laminar flow for a Newtonian fluid and a fully developed velocity profile. The duct consists of an infinite inicial part, insulated on both plates, an intermediale part of finite length, with a prescribed heat flux in the upper plate and insulated on the botton plate, and by another infinite part also insulated on both plates. The problem has been solved by a numerical combination of the integral equation method and the variational method. Both, the performance of the numerical technique employed and results obtained are analyzed in this work. It is demostrated that the heat conduction in the wall significantly modifies the heat transfer parameters. (Author) [pt

A preliminary study on the suitability of host rocks for deep geological disposal of high level radioactive waste in Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, Chun Soo; Bae, Dae Seok; Kim, Kyung Su; Park, Byung Yun; Koh, Young Kown

2000-02-01

It is expected that the key issues are listed as the disposal concept, reference disposal system and other relevant technical development for the deep geological disposal of HLW in each country. First above all, however, the preferred host rocks should be suggested prior execution of these activities. And, it is desirable to be reviewed and proposed some host rocks representative its country. For the reviewing of host rocks in Korean peninsula, several issues were considered such as the long-term geological stability, fracture system, surface and groundwater system and geochemical characteristics in peninsula. The three rock types such as plutonic rocks, crystalline gneisses and massive volcanic rocks were suggested as the preferred host rocks for the R and D of HLW disposal based on the upper stated information. In the following stages, it is suggested that these preferred host rocks would be made an object of all relevant R and D activities for HLW disposal. And, many references for these geologic medium should be characterized and constructed various technical development for the Korean reference disposal system.

A preliminary study on the suitability of host rocks for deep geological disposal of high level radioactive waste in Korea

International Nuclear Information System (INIS)

Kim, Chun Soo; Bae, Dae Seok; Kim, Kyung Su; Park, Byung Yun; Koh, Young Kown

2000-02-01

It is expected that the key issues are listed as the disposal concept, reference disposal system and other relevant technical development for the deep geological disposal of HLW in each country. First above all, however, the preferred host rocks should be suggested prior execution of these activities. And, it is desirable to be reviewed and proposed some host rocks representative its country. For the reviewing of host rocks in Korean peninsula, several issues were considered such as the long-term geological stability, fracture system, surface and groundwater system and geochemical characteristics in peninsula. The three rock types such as plutonic rocks, crystalline gneisses and massive volcanic rocks were suggested as the preferred host rocks for the R and D of HLW disposal based on the upper stated information. In the following stages, it is suggested that these preferred host rocks would be made an object of all relevant R and D activities for HLW disposal. And, many references for these geologic medium should be characterized and constructed various technical development for the Korean reference disposal system

Mineral chemistry of clinopyroxene: guidance on geo- thermobarometry and tectonomagmatic setting of Nabar volcanic rocks, South of Kashan

OpenAIRE

Rezvan Mehvari; Moussa Noghreyan; Mortaza Sharifi; Mohammad Ali Mackizadeh; Seyed Hassan Tabatabaei; Ghodrat Torabi

2017-01-01

Introduction The Nabar area that is a part of the Urumieh- Dokhtar volcano- plutonic belt is located in the south of Kashan. Research works such as Emami (Emami, 1993) and Abbasi (Abbasi, 2012) have been done about the geology of this area. Rock units in the study area contain middle- upper Eocene intermediate to acidic lavas and pyroclastic rocks, green marl, shale and sandy marls of Oligo- Miocene, limestones of Qom formation, intrusive granitoids with Oligo- Miocene age and quaternar...

The impact of the structural features of the rock mass on seismicity in Polish coal mines

Science.gov (United States)

Patyńska, Renata

2017-11-01

The article presents seismic activity induced in the coal mines of the Upper Silesian Coal Basin (GZW) in relation to the locations of the occurrence of rockbursts. The comparison of these measurements with the structural features of the rock mass of coal mines indicates the possibility of estimating the so-called Unitary Energy Expenditure (UEE) in a specific time. The obtained values of UEE were compared with the distribution of seismic activity in GZW mines. The level of seismic activity in the analysed period changed and depended on the intensity of mining works and diverse mining and geological conditions. Five regions, where tremors occurred (Bytom Trough, Main Saddle, Main Trough, Kazimierz Trough, and Jejkowice and Chwałowice Trough) which belong to various structural units of the Upper Silesia were analyzed. It was found out that rock bursts were recorded only in three regions: Main Saddle, Bytom Trough, and Jejkowice and Chwałowice Trough.

Cretaceous and Eocene Adakites in the Sikhote-Alin area (Russian Far East) and their correlation with adakitic rocks in the East Asia continental margin

Science.gov (United States)

Wu, T. J.; Jahn, B. M.

2017-12-01

Adakitic rocks of the Sikhote-Alin area were emplaced during two main periods: the Cretaceous (132-98 Ma) and Eocene (46-39 Ma). These rocks primarily occur in the Khanka Block and, less commonly, in the Sikhote-Alin Orogenic Belt. The adakitic rocks record the following chemical compositions: SiO2 = 57-74%, Al2O3 = 15-18%, Na2O = 3.5-6.1%, K2O = 0.7-3.2%, Na2O/K2O = 1.1-3.9, Sr/Y = 33-145, and (La/Yb)N = 11-53. The HREE and HFSE in these rocks are remarkably depleted. The Early Cretaceous adakites record ɛNd(T) = -1.0 to +3.2 and ISr = 0.7040-0.7090, and the Eocene adakitic rocks record Nd(T) = -2.0 to +2.2 and ISr = 0.7042-0.7058. Adakitic features suggest different modes of magma generation; a comparison of the Sr/Y and La/Yb ratios and geochemical data on Harker diagrams between the two periods of adakitic rocks reveals differences in their petrogenesis. The Cretaceous adakites may have been generated by the partial melting of meta-basic rocks in a subduction zone, accompanied by the emplacement of volcanic arc granitoids. Therefore, the subduction of the Paleo-Pacific Plate beneath the Sikhote-Alin was probably initiated during this time. The Eocene rocks, which record increasing adakitic features with increasing silica content, are most likely the product of andesite that underwent fractionation of mineral assemblage including clinopyoxene, orthopyroxene, garnet and amphibole. These rocks and associated basalts and rhyolite were formed after Cretaceous arc magmatism in the Sikhote-Alin area and were most likely generated by rollback of the subducting Pacific Plate after the Eocene. Abundant adakitic granitoids of Early Cretaceous and Eocene age occur in the Kitakami and Abukuma Mountains of NE Japan. Consequently, it is highly probable that a geological correlation existed between Sikhote-Alin and North Japan, particularly before the opening of the Japan Sea.

Hydraulic Evaluation of Discharge Over Submerged Rock Wing Dams on the Upper Mississippi River

National Research Council Canada - National Science Library

Hendrickson, Jon

1999-01-01

.... This analysis was part of a study, done through the Corps of Engineers' Land Management System, to determine the impacts of zebra mussels on water quality and ecological conditions in the Upper Mississippi River (UMR). Wing dams...

3-D thermo-mechanical laboratory modeling of plate-tectonics: modeling scheme, technique and first experiments

Directory of Open Access Journals (Sweden)

D. Boutelier

2011-05-01

Full Text Available We present an experimental apparatus for 3-D thermo-mechanical analogue modeling of plate tectonic processes such as oceanic and continental subductions, arc-continent or continental collisions. The model lithosphere, made of temperature-sensitive elasto-plastic analogue materials with strain softening, is submitted to a constant temperature gradient causing a strength reduction with depth in each layer. The surface temperature is imposed using infrared emitters, which allows maintaining an unobstructed view of the model surface and the use of a high resolution optical strain monitoring technique (Particle Imaging Velocimetry. Subduction experiments illustrate how the stress conditions on the interplate zone can be estimated using a force sensor attached to the back of the upper plate and adjusted via the density and strength of the subducting lithosphere or the lubrication of the plate boundary. The first experimental results reveal the potential of the experimental set-up to investigate the three-dimensional solid-mechanics interactions of lithospheric plates in multiple natural situations.

On the calculation of crack propagation behavior in disks and plates using a mixed finite method

International Nuclear Information System (INIS)

Fischer, W.

1991-01-01

According to the linear theory of elasticity, infinitely high stresses occur in the crack tips of cracked components. Plastic flow initiation or previous damage, however, will limit these stress singularities to an upper maximum stress for all real materials. To permit acquisition of this highly localized material behavior, while avoiding a very high physical nonlinear calculation effort for the evaluation of crack propagation behavior in disks and plates, models essentially based on Dugdale and Barenblatt are used. This involves determining the stress and displacement conditions required for the simulation of crack propagation by means of a mixed finite method introducing the disk cutting forces and plate curvatures or moments as unknown quantities. In addition to pure disk and plate problems, also coupled disk-plate problems are covered, where the coupling, on one hand, is due to the consideration of high deformations. (orig.) With 66 figs., 8 tabs [de

A summary of the low upper shelf toughness safety margin issue

International Nuclear Information System (INIS)

Merkle, J.G.

1991-01-01

The low upper shelf toughness issue has a long history, beginning with the choice of materials for the submerged arc welding process, but also potentially involving the use of A302-B plate. Criteria for vessels containing low upper shelf materials have usually been expressed in terms of the Charpy upper shelf impact energy. Although these criteria have had several different bases, the range of limiting values for wall thicknesses approaching 229 mm (9 in.) has remained between 54 to 68J (40 to 50 ft lbs). Allowable values for vessels with thinner walls and/or only circumferential low upper shelf welds might conceivably be less. A decision on criteria to be incorporated into the ASME Code is now being made. Choices to be made concern the method for estimating the decrease in upper shelf impact energy, flaw geometry for circumferential welds, statistical significance of toughness values, the choice between J D and J M , reference pressure, safety factors and the inclusion of tearing stability calculations by means of R curve extrapolation. NRC research programs have contributed significantly to the resolution of the low upper shelf issue. These programs embrace all aspects of the issue, including material characterization, large scale testing, analysis and criteria development. 52 refs., 5 figs

New kind of radioactive inclusions in igneous rocks

Energy Technology Data Exchange (ETDEWEB)

Coppens, R

1949-06-20

In previous notes (Compt. rend 228, 176 and 1218(1949)) two sorts of radioactive inclusions in igneous rocks, as recorded on photographic plates, were described: (1) very small (several microns) and strongly radioactive inclusions containing U and Th, (2) crystals of undertermined species, about 1 mm large, containing about 1% Th, and no U. The present note is a report on a third kind of inclusions, observed in a sand from Brittany and in a granite: having an area of several hundredths of mm/sup 2/, they are strongly radioactive; they contain Th, but little or no U; the Th content, which is about 76%, corresponds to pure thorite ThO/sub 2/.SiO/sub 2/.

Rock fracture grouting with microbially induced carbonate precipitation

Science.gov (United States)

Minto, James M.; MacLachlan, Erica; El Mountassir, Gráinne; Lunn, Rebecca J.

2016-11-01

Microbially induced carbonate precipitation has been proposed for soil stabilization, soil strengthening, and permeability reduction as an alternative to traditional cement and chemical grouts. In this paper, we evaluate the grouting of fine aperture rock fractures with calcium carbonate, precipitated through urea hydrolysis, by the bacteria Sporosarcina pasteurii. Calcium carbonate was precipitated within a small-scale and a near field-scale (3.1 m2) artificial fracture consisting of a rough rock lower surfaces and clear polycarbonate upper surfaces. The spatial distribution of the calcium carbonate precipitation was imaged using time-lapse photography and the influence on flow pathways revealed from tracer transport imaging. In the large-scale experiment, hydraulic aperture was reduced from 276 to 22 μm, corresponding to a transmissivity reduction of 1.71 × 10-5 to 8.75 × 10-9 m2/s, over a period of 12 days under constantly flowing conditions. With a modified injection strategy a similar three orders of magnitude reduction in transmissivity was achieved over a period of 3 days. Calcium carbonate precipitated over the entire artificial fracture with strong adhesion to both upper and lower surfaces and precipitation was controlled to prevent clogging of the injection well by manipulating the injection fluid velocity. These experiments demonstrate that microbially induced carbonate precipitation can successfully be used to grout a fracture under constantly flowing conditions and may be a viable alternative to cement based grouts when a high level of hydraulic sealing is required and chemical grouts when a more durable grout is required.

Simulation of water-rock interaction in the yellowstone geothermal system using TOUGHREACT

International Nuclear Information System (INIS)

Dobson, P.F.; Salah, S.; Spycher, N.; Sonnenthal, E.

2003-01-01

The Yellowstone geothermal system provides an ideal opportunity to test the ability of reactive transport models to accurately simulate water-rock interaction. Previous studies of the Yellowstone geothermal system have characterized water-rock interaction through analysis of rocks and fluids obtained from both surface and downhole samples. Fluid chemistry, rock mineralogy, permeability, porosity, and thermal data obtained from the Y-8 borehole in Upper Geyser Basin were used to constrain a series of reactive transport simulations of the Yellowstone geothermal system using TOUGHREACT. Three distinct stratigraphic units were encountered in the 153.4 m deep Y-8 drill core: volcaniclastic sandstone, perlitic rhyolitic lava, and nonwelded pumiceous tuff. The main alteration phases identified in the Y-8 core samples include clay minerals, zeolites, silica polymorphs, adularia, and calcite. Temperatures observed in the Y-8 borehole increase with depth from sub-boiling conditions at the surface to a maximum of 169.8 C at a depth of 104.1 m, with near-isothermal conditions persisting down to the well bottom. 1-D models of the Y-8 core hole were constructed to determine if TOUGHREACT could accurately predict the observed alteration mineral assemblage given the initial rock mineralogy and observed fluid chemistry and temperatures. Preliminary simulations involving the perlitic rhyolitic lava unit are consistent with the observed alteration of rhyolitic glass to form celadonite

Rock burst governance of working face under igneous rock

Science.gov (United States)

Chang, Zhenxing; Yu, Yue

2017-01-01

As a typical failure phenomenon, rock burst occurs in many mines. It can not only cause the working face to cease production, but also cause serious damage to production equipment, and even result in casualties. To explore how to govern rock burst of working face under igneous rock, the 10416 working face in some mine is taken as engineering background. The supports damaged extensively and rock burst took place when the working face advanced. This paper establishes the mechanical model and conducts theoretical analysis and calculation to predict the fracture and migration mechanism and energy release of the thick hard igneous rock above the working face, and to obtain the advancing distance of the working face when the igneous rock fractures and critical value of the energy when rock burst occurs. Based on the specific conditions of the mine, this paper put forward three kinds of governance measures, which are borehole pressure relief, coal seam water injection and blasting pressure relief.

Sedimentary facies of the upper Cambrian (Furongian; Jiangshanian and Sunwaptan) Tunnel City Group, Upper Mississippi Valley: new insight on the old stormy debate

Science.gov (United States)

Eoff, Jennifer D.

2014-01-01

New data from detailed measured sections permit a comprehensive revision of the sedimentary facies of the Furongian (upper Cambrian; Jiangshanian and Sunwaptan stages) Tunnel City Group (Lone Rock Formation and Mazomanie Formation) of Wisconsin and Minnesota. Heterogeneous sandstones, comprising seven lithofacies along a depositional transect from shoreface to transitional-offshore environments, record sedimentation in a storm-dominated, shallow-marine epicontinental sea. The origin of glauconite in the Birkmose Member and Reno Member of the Lone Rock Formation was unclear, but its formation and preserved distribution are linked to inferred depositional energy rather than just net sedimentation rate. Flat-pebble conglomerate, abundant in lower Paleozoic strata, was associated with the formation of a condensed section during cratonic flooding. Hummocky cross-stratification was a valuable tool used to infer depositional settings and relative paleobathymetry, and the model describing formation of this bedform is expanded to address flow types dominant during its genesis, in particular the importance of an early unidirectional component of combined flow. The depositional model developed here for the Lone Rock Formation and Mazomanie Formation is broadly applicable to other strata common to the early Paleozoic that document sedimentation along flooded cratonic interiors or shallow shelves.

North Slope, Alaska: Source rock distribution, richness, thermal maturity, and petroleum charge

Science.gov (United States)

Peters, K.E.; Magoon, L.B.; Bird, K.J.; Valin, Z.C.; Keller, M.A.

2006-01-01

Four key marine petroleum source rock units were identified, characterized, and mapped in the subsurface to better understand the origin and distribution of petroleum on the North Slope of Alaska. These marine source rocks, from oldest to youngest, include four intervals: (1) Middle-Upper Triassic Shublik Formation, (2) basal condensed section in the Jurassic-Lower Cretaceous Kingak Shale, (3) Cretaceous pebble shale unit, and (4) Cretaceous Hue Shale. Well logs for more than 60 wells and total organic carbon (TOC) and Rock-Eval pyrolysis analyses for 1183 samples in 125 well penetrations of the source rocks were used to map the present-day thickness of each source rock and the quantity (TOC), quality (hydrogen index), and thermal maturity (Tmax) of the organic matter. Based on assumptions related to carbon mass balance and regional distributions of TOC, the present-day source rock quantity and quality maps were used to determine the extent of fractional conversion of the kerogen to petroleum and to map the original TOC (TOCo) and the original hydrogen index (HIo) prior to thermal maturation. The quantity and quality of oil-prone organic matter in Shublik Formation source rock generally exceeded that of the other units prior to thermal maturation (commonly TOCo > 4 wt.% and HIo > 600 mg hydrocarbon/g TOC), although all are likely sources for at least some petroleum on the North Slope. We used Rock-Eval and hydrous pyrolysis methods to calculate expulsion factors and petroleum charge for each of the four source rocks in the study area. Without attempting to identify the correct methods, we conclude that calculations based on Rock-Eval pyrolysis overestimate expulsion factors and petroleum charge because low pressure and rapid removal of thermally cracked products by the carrier gas retards cross-linking and pyrobitumen formation that is otherwise favored by natural burial maturation. Expulsion factors and petroleum charge based on hydrous pyrolysis may also be high

Linking plate reconstructions with deforming lithosphere to geodynamic models

Science.gov (United States)

Müller, R. D.; Gurnis, M.; Flament, N.; Seton, M.; Spasojevic, S.; Williams, S.; Zahirovic, S.

2011-12-01

define the thickness of the thermal lithosphere for different continental types, with the exception of the deforming areas that are fully dynamic. Finally, we introduce a "slab assimilation" method in which the thermal structure of the slab, derived analytically, is progressively assimilated into the upper mantle through time. This method not only improves the continuity of slabs in forward models with imposed plate motions, but it also allows us to model flat slab segments that are particularly relevant for understanding dynamic surface topography. When it comes to post-processing and visualisation, GPlates allows the user to import time-dependent model output image stacks to visualise mantle properties (e.g. temperature) at a given depth through time, with plate boundaries and other data attached to plates overlain. This approach provides an avenue to simultaneously investigate the contributions of lithospheric deformation and mantle flow to surface topography. Currently GPlates is being used in conjunction with the codes CitcomS, Terra, BEMEarth and the adaptive mesh refinement code Rhea. A GPlates python plugin infrastructure makes it easy to extend interoperability with other geodynamic modelling codes.

Geochemical constraints on the petrogenesis of the pyroclastic rocks in Abakaliki basin (Lower Benue Rift), Southeastern Nigeria

Science.gov (United States)

Chukwu, Anthony; Obiora, Smart C.

2018-05-01

The pyroclastic rocks in the Cretaceous Abakaliki basin occur mostly as oval-shaped bodies, consisting of lithic/lava and vitric fragments. They are commonly characterized by parallel and cross laminations, as well contain xenoliths of shale, mudstone and siltstones from the older Asu River Group of Albian age. The rocks are basic to ultrabasic in composition, comprising altered alkali basalts, altered tuffs, minor lapillistones and agglomerates. The mineral compositions are characterized mainly by laths of calcic plagioclase, pyroxene (altered), altered olivines and opaques. Calcite, zeolite and quartz represent the secondary mineral constituents. Geochemically, two groups of volcaniclastic rocks, are distinguished: alkaline and tholeiitic rocks, both represented by fresh and altered rock samples. The older alkali basalts occur within the core of the Abakaliki anticlinorium while the younger tholeiites occur towards the periphery. Though most of the rocks are moderate to highly altered [Loss on ignition (LOI, 3.43-22.07 wt. %)], the use of immobile trace element such as Nb, Zr, Y, Hf, Ti, Ta and REEs reflect asthenospheric mantle source compositions. The rocks are enriched in incompatible elements and REEs (∑REE = 87.98-281.0 ppm for alkaline and 69.45-287.99 ppm for tholeiites). The ratios of La/Ybn are higher in the alkaline rocks ranging from 7.69 to 31.55 compared to the tholeiitic rocks which range from 4.4 to 16.89 and indicating the presence of garnet-bearing lherzolite in the source mantle. The spidergrams and REEs patterns along with Zr/Nb, Ba/Nb, Rb/Nb ratios suggest that the rocks were generated by a mantle plume from partial melting of mixed enriched mantle sources (HIMU, EMI and EMII) similar to the rocks of the south Atlantic Ocean such as St. Helena (alkaline rocks) and Ascension rocks (tholeiitic rocks). The rocks were formed in a within-plate setting of the intra-continental rift type similar to other igneous rocks in the Benue Rift and are not

Development of a rocking R/C shear wall system implementing repairable structural fuses

Science.gov (United States)

Parsafar, Saeed; Moghadam, Abdolreza S.

2017-09-01

In the last decades, the concept of earthquake resilient structural systems is becoming popular in which the rocking structure is considered as a viable option for buildings in regions of high seismicity. To this end, a novel wall-base connection based on the " repairable structure" approach is proposed and evaluated. The proposed system is made of several steel plates and high strength bolts act as a friction connection. To achieve the desired rocking motion in the proposed system, short-slotted holes are used in vertical directions for connecting the steel plates to the shear wall (SW). The experimental and numerical studies were performed using a series of displacement control quasi-static cyclic tests on a reference model and four different configurations of the proposed connection installed at the wall corners. The seismic response of the proposed system is compared to the conventional SW in terms of energy dissipation and damage accumulation. In terms of energy dissipation, the proposed system depicted better performance with 95% more energy dissipation capability compared to conventional SW. In terms of damage accumulation, the proposed SW system is nearly undamaged compared to the conventional wall system, which was severely damaged at the wall-base region. Overall, the introduced concept presents a feasible solution for R/C structures when a low-damage design is targeted, which can improve the seismic performance of the structural system significantly.

Radiation shielding plate

International Nuclear Information System (INIS)

Kobayashi, Torakichi; Sugawara, Takeo.

1983-01-01

Purpose: To reduce the weight and stabilize the configuration of a radiation shielding plate which is used in close contact with an object to be irradiated with radiation rays. Constitution: The radiation shielding plate comprises a substrate made of lead glass and a metallic lead coating on the surface of the substrate by means of plating, vapor deposition or the like. Apertures for permeating radiation rays are formed to the radiation shielding plate. Since the shielding plate is based on a lead glass plate, a sufficient mechanical strength can be obtained with a thinner structure as compared with the conventional plate made of metallic lead. Accordingly, if the shielding plate is disposed on a soft object to be irradiated with radiation rays, the object and the plate itself less deform to obtain a radiation irradiation pattern with distinct edges. (Moriyama, K.)

Plating on difficult-to-plate metals: what's new

International Nuclear Information System (INIS)

Wiesner, H.J.

1980-01-01

Some of the changes since 1970 in procedures for plating on such materials as titanium, molybdenum, silicon, aluminum, and gallium arsenide are summarized. While basic procedures for plating some of these materials were developed as many as 30 to 40 years ago, changes in the end uses of the plated products have necessitated new plating processes. In some cases, vacuum techniques - such as ion bombardment, ion implantation, and vacuum metallization - have been introduced to improve the adhesion of electrodeposits. In other cases, these techniques have been used to deposit materials upon which electrodeposits are required

Sedimentology of the upper Karoo fluvial strata in the Tuli Basin, South Africa

Science.gov (United States)

Bordy, Emese M.; Catuneanu, Octavian

2001-08-01

The sedimentary rocks of the Karoo Supergroup in the Tuli Basin (South Africa) may be grouped in four stratigraphic units: the basal, middle and upper units, and the Clarens Formation. This paper presents the findings of the sedimentological investigation of the fluvial terrigenous clastic and chemical deposits of the upper unit. Evidence provided by primary sedimentary structures, palaeontological record, borehole data, palaeo-flow measurements and stratigraphic relations resulted in the palaeo-environmental reconstruction of the upper unit. The dominant facies assemblages are represented by sandstones and finer-grained sediments, which both can be interbedded with subordinate intraformational coarser facies. The facies assemblages of the upper unit are interpreted as deposits of a low-sinuosity, ephemeral stream system with calcretes and silcretes in the dinosaur-inhabited overbank area. During the deposition of the upper unit, the climate was semi-arid with sparse precipitation resulting in high-magnitude, low-frequency devastating flash floods. The current indicators of the palaeo-drainage system suggest flow direction from northwest to southeast, in a dominantly extensional tectonic setting. Based on sedimentologic and biostratigraphic evidence, the upper unit of the Tuli Basin correlates to the Elliot Formation in the main Karoo Basin to the south.

The basic features of clay rock in Tamusu area

International Nuclear Information System (INIS)

Liu Xiaodong; Liu Pinghui

2012-01-01

This paper introduces the Tamusu area location, natural and social economic situation, the regional geological background, as well as the upper Gobi formation of clay rocks, and from the geological conditions, economic conditions, social conditions and other aspects of the Tamusu claystone conducted a preliminary evaluation. The results showed that this area can be used as one of the favorable preselected areas for high-level radioactive waste geological disposal repository, basically meets the siting criteria for geological conditions, environmental protection, land use, social influence and waste transport etc. (authors)

Effect of plate shapes in orifice plate type flowmeters

International Nuclear Information System (INIS)

Moeller, S.V.

1984-01-01

The study of unusual plate shapes in orifice plate type flowmeters is presented, with a view to providing data for the substitution of the plate with one centered circular orifice in those applications where its use is not possible. For this purpose, six pairs of plates with different forms, with and without chamfered edges, were made and tested in a closed water loop. Results show that, generally, the use of chamfers improves the results and, in the case of perforated and slotlike orificed plates, the narrow-ness of the fluid passage tends to make unnecessary its use. (Author) [pt

Influence of porosity and groundmass crystallinity on dome rock strength: a case study from Mt. Taranaki, New Zealand

Science.gov (United States)

Zorn, Edgar U.; Rowe, Michael C.; Cronin, Shane J.; Ryan, Amy G.; Kennedy, Lori A.; Russell, James K.

2018-04-01

Lava domes pose a significant hazard to infrastructure, human lives and the environment when they collapse. Their stability is partly dictated by internal mechanical properties. Here, we present a detailed investigation into the lithology and composition of a Rocks with variable porosity and groundmass crystallinity were compared using measured compressive and tensile strength, derived from deformation experiments performed at room temperature and low (3 MPa) confining pressures. Based on data obtained, porosity exerts the main control on rock strength and mode of failure. High porosity (> 23%) rocks show low rock strength (rocks (5-23%) exhibit higher measured rock strengths (up to 278 MPa) and brittle failure. Groundmass crystallinity, porosity and rock strength are intercorrelated. High groundmass crystal content is inversely related to low porosity, implying crystallisation and degassing of a slowly undercooled magma that experienced rheological stiffening under high pressures deeper within the conduit. This is linked to a slow magma ascent rate and results in a lava dome with higher rock strength. Samples with low groundmass crystallinity are associated with higher porosity and lower rock strength, and represent magma that ascended more rapidly, with faster undercooling, and solidification in the upper conduit at low pressures. Our experimental results show that the inherent strength of rocks within a growing dome may vary considerably depending on ascent/emplacement rates, thus significantly affecting dome stability and collapse hazards.

For Those About to Rock : Naislaulajat rock-genressä

OpenAIRE

Herranen, Linda

2015-01-01

For those about to rock – naislaulajat rock-genressä antaa lukijalleen kokonaisvaltaisen käsityksen naisista rock-genressä: rockin historiasta, sukupuolittuneisuudesta, seksismistä, suomalaisten naislaulajien menestyksestä. Työn aineisto on koottu aihepiirin kirjallisuudesta ja alalla toimiville naislaulajille teetettyjen kyselyiden tuloksista. Lisäksi avaan omia kokemuksiani ja ajatuksiani, jotta näkökulma naisista rock-genressä tulisi esille mahdollisimman monipuolisesti. Ajatus aihees...

Plating laboratory

International Nuclear Information System (INIS)

Seamster, A.G.; Weitkamp, W.G.

1984-01-01

The lead plating of the prototype resonator has been conducted entirely in the plating laboratory at SUNY Stony Brook. Because of the considerable cost and inconvenience in transporting personnel and materials to and from Stony Brook, it is clearly impractical to plate all the resonators there. Furthermore, the high-beta resonator cannot be accommodated at Stony Brook without modifying the set up there. Consequently the authors are constructing a plating lab in-house

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Rheological and geodynamic controls on the mechanisms of subduction and HP/UHP exhumation of crustal rocks during continental collision : Insights from numerical models

NARCIS (Netherlands)

Burov, Evgene; Francois, Thomas; Agard, Philippe; Le Pourhiet, Laetitia; Meyer, Bertrand; Tirel, C.; Lebedev, Sergei; Yamato, Philippe; Brun, Jean Pierre

2014-01-01

While subduction of crustal rocks is increasingly accepted as a common scenario inherent to convergent processes involving continental plates and micro-continents, its occurrence in each particular context, as well as its specific mechanisms and conditions is still debated. The presence of

The 2011 Tohoku-oki Earthquake related to a large velocity gradient within the Pacific plate

Science.gov (United States)

Matsubara, Makoto; Obara, Kazushige

2015-04-01

We conduct seismic tomography using arrival time data picked by the high sensitivity seismograph network (Hi-net) operated by National Research Institute for Earth Science and Disaster Prevention (NIED). We used earthquakes off the coast outside the seismic network around the source region of the 2011 Tohoku-oki Earthquake with the centroid depth estimated from moment tensor inversion by NIED F-net (broadband seismograph network) as well as earthquakes within the seismic network determined by Hi-net. The target region, 20-48N and 120-148E, covers the Japanese Islands from Hokkaido to Okinawa. A total of manually picked 4,622,346 P-wave and 3,062,846 S-wave arrival times for 100,733 earthquakes recorded at 1,212 stations from October 2000 to August 2009 is available for use in the tomographic method. In the final iteration, we estimate the P-wave slowness at 458,234 nodes and the S-wave slowness at 347,037 nodes. The inversion reduces the root mean square of the P-wave traveltime residual from 0.455 s to 0.187 s and that of the S-wave data from 0.692 s to 0.228 s after eight iterations (Matsubara and Obara, 2011). Centroid depths are determined using a Green's function approach (Okada et al., 2004) such as in NIED F-net. For the events distant from the seismic network, the centroid depth is more reliable than that determined by NIED Hi-net, since there are no stations above the hypocenter. We determine the upper boundary of the Pacific plate based on the velocity structure and earthquake hypocentral distribution. The upper boundary of the low-velocity (low-V) oceanic crust corresponds to the plate boundary where thrust earthquakes are expected to occur. Where we do not observe low-V oceanic crust, we determine the upper boundary of the upper layer of the double seismic zone within high-V Pacific plate. We assume the depth at the Japan Trench as 7 km. We can investigate the velocity structure within the Pacific plate such as 10 km beneath the plate boundary since the

Choosing a proper working length can improve the lifespan of locked plates. A biomechanical study.

Science.gov (United States)

Hoffmeier, Konrad L; Hofmann, Gunther O; Mückley, Thomas

2011-05-01

It is hypothesized that the working length influences the implants fatigue behavior. However, few studies addressing this issue came to contrary results. Therefore, we tested systematically the influence of working length and implant material on the plate's endurance. We used an artificial model providing the substantial angle and length conditions of a human femur. A fracture gap of 10mm was bridged with identical shaped plate implants made of stainless steel and grade-2 titanium. The fatigue strength was tested for a short, medium and long working length. Aiming at an implant failure within 80,000 loading cycles the upper load threshold was set to 265N for the titanium plates and to 420N for the steel plates. The lower load threshold was -20N for both plates. For the steel plates there was no correlation between fatigue strength and working length. The construct stiffness did not differ at short and medium working length and was reduced by 10% (P=0.047) at long working length. For the titanium plates the fatigue strength tends to increase with the working length but this correlation was not significant (τ=0.417, P=0.051). Further there was a negative correlation between working length and construct stiffness (τ=0.552; P=0.01). The working length has no appreciable effect on the endurance of the steel plates. Compared to the grade 2-titanium plates the stainless steel plates sustain a larger amount of cyclic load. However, for the titanium plates a larger working length tends to improve the endurance. Copyright © 2010 Elsevier Ltd. All rights reserved.

The human impact on natural rock reserves using basalt, anorthosite, and carbonates as raw materials in insulation products

DEFF Research Database (Denmark)

Dahl, Tais Wittchen; Clausen, Anders U.; Hansen, Peter B.

2011-01-01

lithosphere or subducted with oceanic crust and recycled through the mantle by plate tectonics. Insulation products have a chemical composition similar to average crustal rocks and participate in the natural rock cycle. However, these products need not accumulate in nature, inasmuch as old insulation......Typical crustal rocks such as basalt, limestone, and anorthosite are used in stone wool insulation products. The raw materials for stone wool production are not specific to any rare mineral source but depend upon the mixture of materials having the correct chemical composition, exemplified by 40 wt......% basalt, 20 wt% anorthosite, and 40 wt% cement-bonded renewable materials. This study provides an overview of the natural cycle of these resources, including their abundances in nature, and sets the consumption by the stone wool industry and other human activities in perspective. Basalt, anorthosite...

Art Rocks with Rock Art!

Science.gov (United States)

Bickett, Marianne

2011-01-01

This article discusses rock art which was the very first "art." Rock art, such as the images created on the stone surfaces of the caves of Lascaux and Altimira, is the true origin of the canvas, paintbrush, and painting media. For there, within caverns deep in the earth, the first artists mixed animal fat, urine, and saliva with powdered minerals…

Review of the upper Cenozoic stratigraphy overlying the Columbia River Basalt Group in western Idaho

International Nuclear Information System (INIS)

Strowd, W.B.

1980-12-01

This report is a synthesis of information currently available on the rocks that stratigraphically overlie the Columbia River Basalt Group in Idaho. The primary objective is to furnish a brief but comprehensive review of the literature available on upper Cenozoic rocks in western Idaho and to discuss their general stratigraphic relationships. This study also reviews the derivation of the present stratigraphy and notes weaknesses in our present understanding of the geology and the stratigraphy. This report was prepared in support of a study to evaluate the feasibility of nuclear waste storage in the Columbia River Basalt Group of the Pasco Basin, Washington

Effects of wing locations on wing rock induced by forebody vortices

Directory of Open Access Journals (Sweden)

Ma Baofeng

2016-10-01

Full Text Available Previous studies have shown that asymmetric vortex wakes over slender bodies exhibit a multi-vortex structure with an alternate arrangement along a body axis at high angle of attack. In this investigation, the effects of wing locations along a body axis on wing rock induced by forebody vortices was studied experimentally at a subcritical Reynolds number based on a body diameter. An artificial perturbation was added onto the nose tip to fix the orientations of forebody vortices. Particle image velocimetry was used to identify flow patterns of forebody vortices in static situations, and time histories of wing rock were obtained using a free-to-roll rig. The results show that the wing locations can affect significantly the motion patterns of wing rock owing to the variation of multi-vortex patterns of forebody vortices. As the wing locations make the forebody vortices a two-vortex pattern, the wing body exhibits regularly divergence and fixed-point motion with azimuthal variations of the tip perturbation. If a three-vortex pattern exists over the wing, however, the wing-rock patterns depend on the impact of the highest vortex and newborn vortex. As the three vortices together influence the wing flow, wing-rock patterns exhibit regularly fixed-points and limit-cycled oscillations. With the wing moving backwards, the newborn vortex becomes stronger, and wing-rock patterns become fixed-points, chaotic oscillations, and limit-cycled oscillations. With further backward movement of wings, the vortices are far away from the upper surface of wings, and the motions exhibit divergence, limit-cycled oscillations and fixed-points. For the rearmost location of the wing, the wing body exhibits stochastic oscillations and fixed-points.

Popping Rocks Revealed: Investigations from 14°N on the Mid-Atlantic Ridge

Science.gov (United States)

Wanless, V. D.; Jones, M.; Kurz, M. D.; Soule, S. A.; Fornari, D. J.; Bendana, S.; Mittelstaedt, E. L.

2017-12-01

The popping rock, recovered in dredge 2πD43 in 1985, is commonly considered to be one of the most representative samples of undegassed upper mantle, based on high volatile and noble gas abundances. While this basalt is used to reconstruct mantle volatile contents and CO2 fluxes from mid-ocean ridges (MOR), the origin of the popping rock has remained ambiguous due to a lack of geologic context. Here, we present results from the first combined geochemical, geophysical, and geologic investigation of popping rocks from 14N on the Mid-Atlantic Ridge. By combining lava compositions with high-resolution bathymetric maps, we show that the popping rocks are confined to a single geographic area, at the transition between magmatic and tectonic segments. Fifteen popping rocks were collected in situ using the Alvin submersible in 2016. X-ray microtomography indicates that these lavas have variable vesicle abundances; including the highest vesicularities (>19%) recorded for any MOR basalt. Dissolved CO2 contents (163-175 ppm) are similar to proximal non-popping rocks and are in equilibrium at their eruption depths (>3600 m); however, total CO2 contents (based on vesicularity, dissolved CO2, and vesicle gas contents) are higher than non-popping rocks, ranging from 2800-14150 ppm. The popping rocks have average 3He/4He ratios of 8.17 ± 0.1 Ra and 4He concentrations of 1.84e-5 to 7.67e-5 cc/g STP. Compared to non-popping lavas, the popping rocks have a narrow range of major and trace element concentrations, suggesting little to no crystallization occurred during ascent or eruption. REE patterns and trace element ratios are indistinguishable in the popping rocks (La/Sm = 2.89 ± 0.05), indicating similar mantle sources and extents of melting. Based on lava compositions and spatial distribution, we suggest that the popping rocks at 14N were produced under similar magmatic conditions and erupted over short timescales, perhaps during a series of closely timed eruptions.

Petrogenesis of cataclastic rocks within the San Andreas fault zone of Southern California U.S.A.

Science.gov (United States)

Lawford Anderson, J.; Osborne, Robert H.; Palmer, Donald F.

1980-08-01

This paper petrologically characterizes cataclastic rocks derived from four sites within the San Andreas fault zone of southern California. In this area, the fault traverses an extensive plutonic and metamorphic terrane and the principal cataclastic rock formed at these upper crustal levels is unindurated gouge derived from a range of crystalline rocks including diorite, tonalite, granite, aplite, and pegmatite. The mineralogical nature of this gouge is decidedly different from the "clay gouge" reported by Wu (1975) for central California and is essentially a rock flour with a quartz, feldspar, biotite, chlorite, amphibole, epidote and oxide mineralogy representing the milled-down equivalent of the original rock. Clay development is minor (less than 4 wt. %) to nonexistent and is exclusively kaolinite. Alterations involve hematitic oxidation, chlorite alteration on biotite and amphibole, and local introduction of calcite. Electron microprobe analysis showed that in general the major minerals were not reequilibrated with the pressure—temperature regime imposed during cataclasis. Petrochemically, the form of cataclasis that we have investigated is largely an isochemical process. Some hydration occurs but the maximum amount is less than 2.2% added H 2O. Study of a 375 m deep core from a tonalite pluton adjacent to the fault showed that for Si, Al, Ti, Fe, Mg, Mn, K, Na, Li, Rb, and Ba, no leaching and/or enrichment occurred. Several samples experienced a depletion in Sr during cataclasis while lesser number had an enrichment of Ca (result of calcite veining). Texturally, the fault gouge is not dominated by clay-size material but consists largely of silt and fine sand-sized particles. An intriguing aspect of our work on the drill core is a general decrease in particulate size with depth (and confining pressure) with the predominate shifting sequentially from fine sand to silt-size material. The original fabric of these rocks is commonly not disrupted during the

Characterization of crystalline rocks in the Lake Superior region, USA: implications for nuclear waste isolation

International Nuclear Information System (INIS)

Sood, M.K.; Flower, M.F.J.; Edgar, D.E.

1984-01-01

The Lake Superior region (Wisconsin, the Upper Peninsula of Michigan, and Minnesota) contains 41 Precambrian crystalline rock complexes comprising 64 individual but related rock bodies with known surface exposures. Each complex has a map area greater than 78 km 2 . About 54% of the rock complexes have areas of up to 500 km 2 , 15% fall between 500 km 2 and 1000 km 2 , 19% lie between 1000 km 2 and 2500 km 2 , and 12% are over 2500 km 2 . Crystalline rocks of the region vary widely in composition, but they are predominantly granitic. Repeated thermo-tectonic events have produced early Archean gneisses, migmatites, and amphibolites with highly tectonized fabrics that impart a heterogeneous and anisotropic character to the rocks. Late Archean rocks are usually but not invariably gneissose and migmatitic. Proterozoic rocks of the region include synorogenic (foliated) granitic rocks, anorogenic (non-foliated) granites, and the layered gabbro-anorthosite-troctolite intrusives of the rift-related Keweenawan igneous activity. Compared with the Archean rocks of the region, the Proterozoic bodies generally lack highly tectonized fabrics and have more definable contacts where visible. Anorogenic intrusions are relatively homogeneous and isotropic. On the basis of observed geologic characteristics, postorogenic and anorogenic crystalline rock bodies located away from recognized tectonic systems have attributes that make them relatively more desirable as a possible site for a nuclear waste repository in the region. This study was conducted at Argonne National Laboratory under the sponsorship of the US Department of Energy through the Office of Crystalline Repository Development at Battelle Memorial Institute, Columbus, Ohio. 84 references, 4 figures, 3 tables

Characterization of crystalline rocks in the Lake Superior region, USA: implications for nuclear waste isolation

International Nuclear Information System (INIS)

Sood, M.K.; Edgar, D.E.; Flower, M.F.J.

1984-01-01

The Lake Superior region (Wisconsin, the Upper Peninsula of Michigan, and Minnesota) contains 41 Precambrian crystalline (medium- to coarse-grained igneous and high-grade metamorphic) rock complexes comprising 64 individual but related rock bodies with known surface exposures. Each complex has a map area greater than 78 km 2 . About 54% of the rock complexes have areas of up to 500 km 2 , 15% fall between 500 km 2 and 1000 km 2 , 19% lie between 1000 km 2 and 2500 km 2 , and 12% are over 2500 km 2 . Crystalline rocks of the region vary widely in composition, but they are predominantly granitic. Repeated thermo-tectonic events have produced early Archean gneisses, migmatites, and amphibolites with highly tectonized fabrics that impart a heterogeneous and anisotropic character to the rocks. Late Archean rocks are usually but not invariably gneissose an migmatitic. Proterozoic rocks of the region include synorogenic (foliated) granitic rocks, anorogenic (nonfoliated) granites, and the layered gabbro-anorthosite-troctolite intrusives of the rift-related Keweenawan igneous activity. Compared with the Archean rocks of the region, the Proterozoic bodies generally lack highly tectonized fabrics and have more definable contacts where visible. Anorogenic intrusions are relatively homogeneous and isotropic. On the basis of observed geologic characteristics, postorogenic and anorogenic crystalline rock bodies located away from recognized tectonic systems have attributes that make them relatively more desirable as a possible site for a nuclear waste repository in the region. This study was conducted at Argonne National Laboratory under the sponsorship of the US Department of Energy through the Office of Crystalline Repository Development at Battelle Memorial Institute, Columbus, Ohio

Imaging the deep structures of the convergent plates along the Ecuadorian subduction zone through receiver function analysis

Science.gov (United States)

Galve, A.; Charvis, P.; Regnier, M. M.; Font, Y.; Nocquet, J. M.; Segovia, M.

2017-12-01

The Ecuadorian subduction zone was affected by several large M>7.5 earthquakes. While we have low resolution on the 1942, 1958 earthquakes rupture zones extension, the 2016 Pedernales earthquake, that occurs at the same location than the 1942 earthquake, give strong constraints on the deep limit of the seismogenic zone. This downdip limit is caused by the onset of plasticity at a critical temperature (> 350-450 °C for crustal materials, or serpentinized mantle wedge, and eventually > 700 °C for dry mantle). However we still don't know exactly where is the upper plate Moho and therefore what controls the downdip limit of Ecuadorian large earthquakes seismogenic zone. For several years Géoazur and IG-EPN have maintained permanent and temporary networks (ADN and JUAN projects) along the margin to register the subduction zone seismological activity. Although Ecuador is not a good place to perform receiver function due to its position with respect to the worldwide teleseismic sources, the very long time deployment compensate this issue. We performed a frequency dependent receiver function analysis to derive (1) the thickness of the downgoing plate, (2) the interplate depth and (3) the upper plate Moho. These constraints give the frame to interpretation on the seismogenic zone of the 2016 Pedernales earthquake.

Influence of stress on the permeability of coal and sedimentary rocks of the Upper Silesian Basin

Czech Academy of Sciences Publication Activity Database

Konečný, Pavel; Kožušníková, Alena

2011-01-01

Roč. 48, č. 2 (2011), s. 347-352 ISSN 1365-1609 Institutional research plan: CEZ:AV0Z30860518 Keywords : permeability * triaxial test * coal and sedimentary rocks Subject RIV: DH - Mining, incl. Coal Mining Impact factor: 1.272, year: 2011 http://www.sciencedirect.com/science/article/pii/S1365160910002194

Create Your Plate

Medline Plus

Full Text Available ... Plate Share Create Your Plate ! Share: Seven Simple Steps to Create Your Plate It's simple and effective ... foods within each food category. Try these seven steps to get started: Using your dinner plate, put ...

Parallelized FDTD simulation for flat-plate bounded wave EMP simulator with lumped terminator

International Nuclear Information System (INIS)

Zhu Xiangqin; Chen Weiqing; Chen Zaigao; Cai Libing; Wang Jianguo

2013-01-01

A parallelized finite-difference time-domain(FDTD) method for simulating the bounded wave electromagnetic pulse (EMP) simulator with lumped terminator and parallel plate is presented. The effects of several model-parameters on the simulator to the fields in the working volume are simulated and analyzed. The results show that if the width of the lower PEC plate is(or is bigger than)1.5 times that of the upper plate of working volume, the projection length of front transitional section does not have a significant effect on the rise-times of electric fields at the points near the front transitional section, and the rise-times of electric fields at the points near the working volume center decrease as the projection length increases, but the decrement of rise-time decreases. The rise-times of E z at all points also decrease as the lower PEC plate's width increases, but the decrements of rise-time decreases. If the projection length of the front transitional section is fixed, the good results can not be obtained by increasing or decreasing the height of the simulator only, however, which has an optimal value. (authors)

The Usability of Rock-Like Materials for Numerical Studies on Rocks

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

The approaches of synthetic rock material and mass are widely used by many researchers for understanding the failure behavior of different rocks. In order to model the failure behavior of rock material, researchers take advantageous of different techniques and software. But, the majority of all these instruments are based on distinct element method (DEM). For modeling the failure behavior of rocks, and so to create a fundamental synthetic rock material model, it is required to perform related laboratory experiments for providing strength parameters. In modelling studies, model calibration processes are performed by using parameters of intact rocks such as porosity, grain size, modulus of elasticity and Poisson ratio. In some cases, it can be difficult or even impossible to acquire representative rock samples for laboratory experiments from heavily jointed rock masses and vuggy rocks. Considering this limitation, in this study, it was aimed to investigate the applicability of rock-like material (e.g. concrete) to understand and model the failure behavior of rock materials having complex inherent structures. For this purpose, concrete samples having a mixture of %65 cement dust and %35 water were utilized. Accordingly, intact concrete samples representing rocks were prepared in laboratory conditions and their physical properties such as porosity, pore size and density etc. were determined. In addition, to acquire the mechanical parameters of concrete samples, uniaxial compressive strength (UCS) tests were also performed by simultaneously measuring strain during testing. The measured physical and mechanical properties of these extracted concrete samples were used to create synthetic material and then uniaxial compressive tests were modeled and performed by using two dimensional discontinuum program known as Particle Flow Code (PFC2D). After modeling studies in PFC2D, approximately similar failure mechanism and testing results were achieved from both experimental and

Hot Dry Rock; Geothermal Energy

Energy Technology Data Exchange (ETDEWEB)

None

1990-01-01

The commercial utilization of geothermal energy forms the basis of the largest renewable energy industry in the world. More than 5000 Mw of electrical power are currently in production from approximately 210 plants and 10 000 Mw thermal are used in direct use processes. The majority of these systems are located in the well defined geothermal generally associated with crustal plate boundaries or hot spots. The essential requirements of high subsurface temperature with huge volumes of exploitable fluids, coupled to environmental and market factors, limit the choice of suitable sites significantly. The Hot Dry Rock (HDR) concept at any depth originally offered a dream of unlimited expansion for the geothermal industry by relaxing the location constraints by drilling deep enough to reach adequate temperatures. Now, after 20 years intensive work by international teams and expenditures of more than $250 million, it is vital to review the position of HDR in relation to the established geothermal industry. The HDR resource is merely a body of rock at elevated temperatures with insufficient fluids in place to enable the heat to be extracted without the need for injection wells. All of the major field experiments in HDR have shown that the natural fracture systems form the heat transfer surfaces and that it is these fractures that must be for geothermal systems producing from naturally fractured formations provide a basis for directing the forthcoming but, equally, they require accepting significant location constraints on HDR for the time being. This paper presents a model HDR system designed for commercial operations in the UK and uses production data from hydrothermal systems in Japan and the USA to demonstrate the reservoir performance requirements for viable operations. It is shown that these characteristics are not likely to be achieved in host rocks without stimulation processes. However, the long term goal of artificial geothermal systems developed by systematic

Dating and source determination of volcanic rocks from Khunik area (South of Birjand, South Khorasan using Rb-Sr and Sm-Nd isotopes

Directory of Open Access Journals (Sweden)

Somayeh Samiee

2016-12-01

Full Text Available The Khunik area is located in the south of Birjand, Khorasan province, in the eastern margin of Lut block. Tertiary volcanic rocks have andesite to trachy-andesite composition. Dating analyzing by Rb-Sr method on plagioclase and hornblende as well as whole-rock isochron method was performed on pyroxene-hornblende andesite rock unit. On this basis the emplacement age is Upper Paleocene (58±11 Ma. These rocks have initial 87Sr/86Sr and εNd 0.7046-0.7049 and 2.16-3.12, respectively. According to isotopic data, volcanic rocks originated from depleted mantle and have the least crust contamination while it was fractionated. Geochemically, Khunik volcanic rocks have features typical of calk-alkaline to shoshonite and are metaluminous. Enrichment in LILEs and typical negative anomalies of Nb and Ti are evidences that the volcanic rocks formed in a subduction zone and active continental margin. Modeling suggests that these rocks were derived dominantly from 1–5% partial melting of a mainly spinel garnet lherzolite mantle source that is metasomatized by slab-derived fluid.

On the age of the Onverwacht Group, Swaziland sequence, South Africa. [radioactive dating of stratified igneous rocks

Science.gov (United States)

Jahn, B.-M.; Shih, C.-Y.

1974-01-01

Some rocks of the Onverwacht Group, South Africa, have been analyzed for Rb and Sr concentrations and Sr isotopic composition. These rocks include volcanic rocks, layered ultramafic differentiates and cherty sediments. Whole rock data indicate that the Rb-Sr isotopic systems in many samples were open and yield no reasonable isochron relationships. However, the data of mineral separates from a basaltic komatiite define a good isochron of 3.50 (plus or minus .2) b.y. with an initial Sr-87/Sr-86 ratio of 0.70048 plus or minus 5. The orthodox interpretation of this age is the time of the low grade metamorphism. It is reasonable to assume that the age of 3.50 b.y. might also represent the time of initial Onverwacht volcanism and deposition. The initial Sr-87/Sr-86 ratio obtained above is important to an understanding of the Sr isotopic composition of the Archean upper mantle.

K-Ar ages of rocks from Lago Alumine, Rucachoroi and Quillen, North Patagonian Andes, Neuquen, Republica Argentina

International Nuclear Information System (INIS)

Latorre, Carlos O.; Vattuone, M.E; Linares, Enrique; Leal, Pablo R

2001-01-01

This study presents new K-Ar ages of granitic rocks from the Patagonian Batholit in the North Patagonian Andes (38 o 00'- 39 o 30' SL), from localities near Alumine lake and from Norquinco lake to Quillen valley, in the Neuquen Province, Argentine. The granitic rocks of Patagonia had been recognized as Upper Paleozoic to Middle Jurassic batholits and as Late Jurassic to Tertiary batholiths (Rapela and Pankhurst, 1992). Geochronologically, Rapela and Kay (1988) had distinguished Early Cretaceous (140 to 120 Ma) and Late Cretaceous (110 to 75 Ma ) magmatic episodes based in potassium-argon data. For the granitic rocks of the area of Paso Icalma, Moquehue and the Rahue granodiorites, Cingolani et al. (1991) presented Rb-Sr whole rock isochron ages of 70±10 Ma, 209±13 Ma and 237±37 Ma, respectively, and Varela et al. (1994), with the same method, cited an age of 285±5 Ma for the Rahue granodiorites and diorites (au)

Rock Art

Science.gov (United States)

Henn, Cynthia A.

2004-01-01

There are many interpretations for the symbols that are seen in rock art, but no decoding key has ever been discovered. This article describes one classroom's experiences with a lesson on rock art--making their rock art and developing their own personal symbols. This lesson allowed for creativity, while giving an opportunity for integration…

Paper microzone plates.

Science.gov (United States)

Carrilho, Emanuel; Phillips, Scott T; Vella, Sarah J; Martinez, Andres W; Whitesides, George M

2009-08-01

This paper describes 96- and 384-microzone plates fabricated in paper as alternatives to conventional multiwell plates fabricated in molded polymers. Paper-based plates are functionally related to plastic well plates, but they offer new capabilities. For example, paper-microzone plates are thin (approximately 180 microm), require small volumes of sample (5 microL per zone), and can be manufactured from inexpensive materials ($0.05 per plate). The paper-based plates are fabricated by patterning sheets of paper, using photolithography, into hydrophilic zones surrounded by hydrophobic polymeric barriers. This photolithography used an inexpensive formulation photoresist that allows rapid (approximately 15 min) prototyping of paper-based plates. These plates are compatible with conventional microplate readers for quantitative absorbance and fluorescence measurements. The limit of detection per zone loaded for fluorescence was 125 fmol for fluorescein isothiocyanate-labeled bovine serum albumin, and this level corresponds to 0.02 the quantity of analyte per well used to achieve comparable signal-to-noise in a 96-well plastic plate (using a solution of 25 nM labeled protein). The limits of detection for absorbance on paper was approximately 50 pmol per zone for both Coomassie Brilliant Blue and Amaranth dyes; these values were 0.4 that required for the plastic plate. Demonstration of quantitative colorimetric correlations using a scanner or camera to image the zones and to measure the intensity of color, makes it possible to conduct assays without a microplate reader.

Importance of upper-limb inertia in calculating concentric bench press force.

Science.gov (United States)

Rambaud, Olivier; Rahmani, Abderrahmane; Moyen, Bernard; Bourdin, Muriel

2008-03-01

The purpose of this study was to investigate the influence of upper-limb inertia on the force-velocity relationship and maximal power during concentric bench press exercise. Reference peak force values (Fpeakp) measured with a force plate positioned below the bench were compared to those measured simultaneously with a kinematic device fixed on the barbell by taking (Fpeakt) or not taking (Fpeakb) upper-limb inertia into account. Thirteen men (27.8 +/- 4.1 years, 184.6 +/- 5.5 cm, 99.5 +/- 18.6 kg) performed all-out concentric bench press exercise against 8 loads ranging between 7 and 74 kg. The results showed that for each load, Fpeakb was significantly less than Fpeakp (P force (F0), maximal velocity (V0), optimal velocity (Vopt), and maximal power (Pmax), extrapolated from the force- and power-velocity relationships determined with the kinematic device, were significantly underestimated when upper-limb inertia was ignored. The results underline the importance of taking account of the total inertia of the moving system to ensure precise evaluation of upper-limb muscular characteristics in all-out concentric bench press exercise with a kinematic device. A major application of this study would be to develop precise upper-limb muscular characteristic evaluation in laboratory and field conditions by using a simple and cheap kinematic device.

Geologic assessment of undiscovered oil and gas resources—Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups, United States Gulf of Mexico Coastal Plain and State Waters

Science.gov (United States)

Swanson, Sharon M.; Enomoto, Catherine B.; Dennen, Kristin O.; Valentine, Brett J.; Cahan, Steven M.

2017-02-10

In 2010, the U.S. Geological Survey (USGS) assessed Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups and their equivalent units for technically recoverable, undiscovered hydrocarbon resources underlying onshore lands and State Waters of the Gulf Coast region of the United States. This assessment was based on a geologic model that incorporates the Upper Jurassic-Cretaceous-Tertiary Composite Total Petroleum System (TPS) of the Gulf of Mexico basin; the TPS was defined previously by the USGS assessment team in the assessment of undiscovered hydrocarbon resources in Tertiary strata of the Gulf Coast region in 2007. One conventional assessment unit (AU), which extends from south Texas to the Florida panhandle, was defined: the Fredericksburg-Buda Carbonate Platform-Reef Gas and Oil AU. The assessed stratigraphic interval includes the Edwards Limestone of the Fredericksburg Group and the Georgetown and Buda Limestones of the Washita Group. The following factors were evaluated to define the AU and estimate oil and gas resources: potential source rocks, hydrocarbon migration, reservoir porosity and permeability, traps and seals, structural features, paleoenvironments (back-reef lagoon, reef, and fore-reef environments), and the potential for water washing of hydrocarbons near outcrop areas.In Texas and Louisiana, the downdip boundary of the AU was defined as a line that extends 10 miles downdip of the Lower Cretaceous shelf margin to include potential reef-talus hydrocarbon reservoirs. In Mississippi, Alabama, and the panhandle area of Florida, where the Lower Cretaceous shelf margin extends offshore, the downdip boundary was defined by the offshore boundary of State Waters. Updip boundaries of the AU were drawn based on the updip extent of carbonate rocks within the assessed interval, the presence of basin-margin fault zones, and the presence of producing wells. Other factors evaluated were the middle

Contribution To The Geology Of Basement Rocks In The South Western Desert Of Egypt

International Nuclear Information System (INIS)

Sadek, M.F.; Khyamy, A.A.

2003-01-01

Three major Precambrian basement inliers are exposed in the South Western Desert of Egypt between Long. 29 degree E and the River Nile within the Uweinat-Bir Safsaf-Aswan E-W uplift system. These are Bir Safsaf, Gabal EI-Asr and Gabal Umm Shaghir areas. Smaller outcrops include Gabal EI-Gara El-Hamra and Gabal El-Gara EI-Soda, Gabal Siri, GabaI EI-Fantas and Aswan-Kalabsha area as well as the scattered outcrops around Darb El-Arbain road. Band ratios 5/7, 5/1, 4 of Landsat TM images were applied to delineate the borders, the lithologic units and structural features of low relief basement outcrops within the surrounding flat lying sedimentary rocks and sand plains. These basement rocks comprise ortho gneisses (assumed by many authors as related to old continent pre Pan-African rocks), G 1 tonalite-granodiorite, and G2 monzogranite-alkali feldspar granite intruded by variable dykes. The boundaries between the basement exposures and the sedimentary rocks are marked by nonconformity surfaces or sets of faults. Both basement and sedimentary rocks are intruded by Mesozoic syenite-G3 granites, rhyolite, trachytic plugs and Upper Cretaceous to Tertiary basalts. The basement exposures are structurally controlled by major E- W fault systems. Their vertical uplifting is overprinted by folding the overlying sedimentary rocks. This study revealed that, the different basement exposures in the SE of the Western Desert of Egypt are similar in appearance and field relations to the Pan-African basement rocks extending towards the east of the River Nile and exposed everywhere in the Eastern Desert of Egypt

Spatial statistics for predicting flow through a rock fracture

International Nuclear Information System (INIS)

Coakley, K.J.

1989-03-01

Fluid flow through a single rock fracture depends on the shape of the space between the upper and lower pieces of rock which define the fracture. In this thesis, the normalized flow through a fracture, i.e. the equivalent permeability of a fracture, is predicted in terms of spatial statistics computed from the arrangement of voids, i.e. open spaces, and contact areas within the fracture. Patterns of voids and contact areas, with complexity typical of experimental data, are simulated by clipping a correlated Gaussian process defined on a N by N pixel square region. The voids have constant aperture; the distance between the upper and lower surfaces which define the fracture is either zero or a constant. Local flow is assumed to be proportional to local aperture cubed times local pressure gradient. The flow through a pattern of voids and contact areas is solved using a finite-difference method. After solving for the flow through simulated 10 by 10 by 30 pixel patterns of voids and contact areas, a model to predict equivalent permeability is developed. The first model is for patterns with 80% voids where all voids have the same aperture. The equivalent permeability of a pattern is predicted in terms of spatial statistics computed from the arrangement of voids and contact areas within the pattern. Four spatial statistics are examined. The change point statistic measures how often adjacent pixel alternate from void to contact area (or vice versa ) in the rows of the patterns which are parallel to the overall flow direction. 37 refs., 66 figs., 41 tabs

Finite element analysis of plate rolling of duplex-layer steels for long-period fast reactor application

International Nuclear Information System (INIS)

Lee, Jungki; Kim, Ji Hyun

2015-01-01

With same roll speed and same friction coefficient, curvature is formed on rolled product from FEA result. To reduce this curvature and plastic strain which cause reduction in fabricability, two ways are selected; (i) controlling upper/lower roll speed, and (ii) adjusting upper/lower friction coefficient and contacts. Both results shows it can reduce the curvature and equivalent plastic strain of the plate after the rolling. It can be applied in real plate rolling processing and also the next research for pilgering process for tube and pipe production. The FEA results of equivalent stress and plastic deformation distribution are showed in figure 5. The von-Mises equivalent stress distribution showed that the stress is still concentrated on upper Fe-12Cr-2Si layer, however, it also shows that equivalent plastic strain is distributed uniformly comparing with upper and lower roll speed ratio is 1.0. In high temperature liquid metal environment, there are usually two types of corrosion; one is corrosion by dissolution of alloy elements into liquid metal, and another is corrosion by chemical reaction among impurities in liquid metal and structural alloy. There have been some researches to develop new alloys that can form more dense scale on the surface even in wider impurity range and higher temperature range . M.P Short et al. devised functionally graded composite which is composed of two layers . one is a thin corrosion resistant layer and another is thick structural layer which guarantees mechanical strength, creep rupture strength and shows less irradiation swelling

Tomography images of the Alpine roots and surrounding upper mantle

Science.gov (United States)

Plomerova, Jaroslava; Babuska, Vladislav

2017-04-01

Teleseismic body-wave tomography represents powerful tool to study regional velocity structure of the upper mantle and to image velocity anomalies, such as subducted lithosphere plates in collisional zones. In this contribution, we recapitulate 3D models of the upper mantle beneath the Alps, which developed at a collision zone of the Eurasian and African plates. Seismic tomography studies indicate a leading role of the rigid mantle lithosphere that functioned as a major stress guide during the plate collisions. Interactions of the European lithosphere with several micro-plates in the south resulted in an arcuate shape of this mountain range on the surface and in a complicated geometry of the Alpine subductions in the mantle. Early models with one bended lithosphere root have been replaced with more advanced models showing two separate lithosphere roots beneath the Western and Eastern Alps (Babuska et al., Tectonophysics 1990; Lippitsch et al., JGR 2003). The standard isotropic velocity tomography, based on pre-AlpArray data (the currently performed passive seismic experiment in the Alps and surroundings) images the south-eastward dipping curved slab of the Eurasian lithosphere in the Western Alps. On the contrary, beneath the Eastern Alps the results indicate a very steep northward dipping root that resulted from the collision of the European plate with the Adriatic microplate. Dando et al. (2011) interpret high-velocity heterogeneities at the bottom of their regional tomographic model as a graveyard of old subducted lithospheres. High density of stations, large amount of rays and dense ray-coverage of the volume studied are not the only essential pre-requisites for reliable tomography results. A compromise between the amount of pre-processed data and the high-quality of the tomography input (travel-time residuals) is of the high importance as well. For the first time, the existence of two separate roots beneath the Alps has been revealed from carefully pre

Stratigraphy and uranium potential of early proterozoic metasedimentary rocks in the Medicine Bow Mountains, Wyoming

International Nuclear Information System (INIS)

Karlstrom, K.E.; Houston, R.S.

1979-01-01

The Medicine Bow Mountains of southeastern Wyoming contain an eight mile (13 km) thick section of Early Proterozoic (2500 to 1700 My b.p.) metasedimentary rocks which is subdivided into three successions: the Phantom Lake Metamorphic Suite (oldest), Deep Lake Group, and Libby Creek Group. The most promising units are the basal conglomerate of the upper Phantom Lake Suite, which appears to unconformably overlie metavolcanics of the lower Phantom Lake Suite, and the Magnolia Formation, which unconformably overlies the upper Phantom Lake Suite. Outcrops of the former have yielded assays of up to 141 ppM U and 916 ppM Th, with no appreciable gold. Outcrops of the Magnolia Formation have yielded up to 8.4 ppM U and 38 ppM Th. Several factors indicate that these units deserve further study. First, the lithologies of the radioactive and nonradioactive units are remarkably similar to those found in known uranium fossil-placers. Second, the paleogeography was favorable for placer accumulation if the conglomerates are fluvial sediments in an epicontinental clastic succession which was deposited during several transgressive-regressive cycles, as interpreted to be, Third, the age of the conglomerates may be similar to the age of other known uranium placers-i.e., more than 2000 My b.p. And fourth, geological and geochemical studies indicate that both uranium and pyrite have been strongly leached from outcrops and that subsurface rocks contain more uranium than surface rocks do

49 CFR 572.165 - Upper and lower torso assemblies and torso flexion test procedure.

Science.gov (United States)

2010-10-01

...) ANTHROPOMORPHIC TEST DEVICES Hybrid III Six-Year-Old Weighted Child Test Dummy § 572.165 Upper and lower torso... determine the stiffness effects of the lumbar spine (specified in 49 CFR 572.125(a)), including cable... bushing (specified in 49 CFR 572.125(a)), nut (specified in 49 CFR 572.125(a)), spine box weighting plates...

Thermally induced rock stress increment and rock reinforcement response

International Nuclear Information System (INIS)

Hakala, M.; Stroem, J.; Nujiten, G.; Uotinen, L.; Siren, T.; Suikkanen, J.

2014-07-01

This report describes a detailed study of the effect of thermal heating by the spent nuclear fuel containers on the in situ rock stress, any potential rock failure, and associated rock reinforcement strategies for the Olkiluoto underground repository. The modelling approach and input data are presented together repository layout diagrams. The numerical codes used to establish the effects of heating on the in situ stress field are outlined, together with the rock mass parameters, in situ stress values, radiogenic temperatures and reinforcement structures. This is followed by a study of the temperature and stress evolution during the repository's operational period and the effect of the heating on the reinforcement structures. It is found that, during excavation, the maximum principal stress is concentrated at the transition areas where the profile changes and that, due to the heating from the deposition of spent nuclear fuel, the maximum principal stress rises significantly in the tunnel arch area of NW/SW oriented central tunnels. However, it is predicted that the rock's crack damage (CD, short term strength) value of 99 MPa will not be exceeded anywhere within the model. Loads onto the reinforcement structures will come from damaged and loosened rock which is assumed in the modelling as a free rock wedge - but this is very much a worst case scenario because there is no guarantee that rock cracking would form a free rock block. The structural capacity of the reinforcement structures is described and it is predicted that the current quantity of the rock reinforcement is strong enough to provide a stable tunnel opening during the peak of the long term stress state, with damage predicted on the sprayed concrete liner. However, the long term stability and safety can be improved through the implementation of the principles of the Observational Method. The effect of ventilation is also considered and an additional study of the radiogenic heating effect on the brittle

Thermally induced rock stress increment and rock reinforcement response

Energy Technology Data Exchange (ETDEWEB)

Hakala, M. [KMS Hakala Oy, Nokia (Finland); Stroem, J.; Nujiten, G.; Uotinen, L. [Rockplan, Helsinki (Finland); Siren, T.; Suikkanen, J.

2014-07-15

This report describes a detailed study of the effect of thermal heating by the spent nuclear fuel containers on the in situ rock stress, any potential rock failure, and associated rock reinforcement strategies for the Olkiluoto underground repository. The modelling approach and input data are presented together repository layout diagrams. The numerical codes used to establish the effects of heating on the in situ stress field are outlined, together with the rock mass parameters, in situ stress values, radiogenic temperatures and reinforcement structures. This is followed by a study of the temperature and stress evolution during the repository's operational period and the effect of the heating on the reinforcement structures. It is found that, during excavation, the maximum principal stress is concentrated at the transition areas where the profile changes and that, due to the heating from the deposition of spent nuclear fuel, the maximum principal stress rises significantly in the tunnel arch area of NW/SW oriented central tunnels. However, it is predicted that the rock's crack damage (CD, short term strength) value of 99 MPa will not be exceeded anywhere within the model. Loads onto the reinforcement structures will come from damaged and loosened rock which is assumed in the modelling as a free rock wedge - but this is very much a worst case scenario because there is no guarantee that rock cracking would form a free rock block. The structural capacity of the reinforcement structures is described and it is predicted that the current quantity of the rock reinforcement is strong enough to provide a stable tunnel opening during the peak of the long term stress state, with damage predicted on the sprayed concrete liner. However, the long term stability and safety can be improved through the implementation of the principles of the Observational Method. The effect of ventilation is also considered and an additional study of the radiogenic heating effect on the

Comparison of disposal concepts for rock salt and hard rock

International Nuclear Information System (INIS)

Papp, R.

1998-01-01

The study was carried out in the period 1994-1996. The goals were to prepare a draft on spent fuel disposal in hard rock and additionally a comparison with existing disposal concepts for rock salt. A cask for direct disposal of spent fuel and a repository for hard rock including a safeguards concept were conceptually designed. The results of the study confirm, that the early German decision to employ rock salt was reasonable. (orig.)

Radioactivity and decay heat generation in precambrian magmatic rocks (with the South Pamirs as an example)

International Nuclear Information System (INIS)

Batyrmurzaev, A.S.; Alibekov, G.I.; Bekieva, A.A.

2003-01-01

The evaluation of the heat generation share in the results of the long-living radioactive elements (RAE) decay in the Earth surface layers is accomplished on the basis of the data on the uranium and thorium concentration in the precambrian magmatic rocks of the South Pamirs. It was supposed by the calculations, that the value of the heat flux, generated by the rocks, is determined mainly by the RAE content in the Earth upper layer crust itself of 10-15 km. It is shown that the radioheat generation share is within the range of 5-10% from the measured values of the geothermal flows [ru

Summary of HSST wide-plate crack-arrest tests and analyses

International Nuclear Information System (INIS)

Naus, D.J.; Bass, B.R.; Keeney-Walker, J.; Fields, R.J.; DeWit, R.; Low, S.R. III

1988-01-01

Eleven wide-plate crack-arrest tests have been completed to date, seven utilizing specimens fabricated from A533B class 1 material (WP-1 series), and four fabricated from a low upper-shelf base material (WP-2 series). With the exception of one test in the WP-1 series and two tests in the WP-2 series which utilized 152-mm-thick specimens, each test utilized a single-edge notched (SEN) plate specimen 1 by 1 by 0.1 m that was subjected to a linear thermal gradient along the plane of crack propagation. Test results exhibit an increase in crack-arrest toughness with temperature, with the rate of increase becoming greater as the temperature increases. When the wide-place test results are combined with other large-specimen results (Japanese ESSO, thermal-shock experiments and pressurized-thermal-shock experiments) the data show a consistent trend in which the K Ia data extends above the limit provided in ASME Section XI. (author)

Mechanism of Rock Burst Occurrence in Specially Thick Coal Seam with Rock Parting

Science.gov (United States)

Wang, Jian-chao; Jiang, Fu-xing; Meng, Xiang-jun; Wang, Xu-you; Zhu, Si-tao; Feng, Yu

2016-05-01

Specially thick coal seam with complex construction, such as rock parting and alternative soft and hard coal, is called specially thick coal seam with rock parting (STCSRP), which easily leads to rock burst during mining. Based on the stress distribution of rock parting zone, this study investigated the mechanism, engineering discriminant conditions, prevention methods, and risk evaluation method of rock burst occurrence in STCSRP through setting up a mechanical model. The main conclusions of this study are as follows. (1) When the mining face moves closer to the rock parting zone, the original non-uniform stress of the rock parting zone and the advancing stress of the mining face are combined to intensify gradually the shearing action of coal near the mining face. When the shearing action reaches a certain degree, rock burst easily occurs near the mining face. (2) Rock burst occurrence in STCSRP is positively associated with mining depth, advancing stress concentration factor of the mining face, thickness of rock parting, bursting liability of coal, thickness ratio of rock parting to coal seam, and difference of elastic modulus between rock parting and coal, whereas negatively associated with shear strength. (3) Technologies of large-diameter drilling, coal seam water injection, and deep hole blasting can reduce advancing stress concentration factor, thickness of rock parting, and difference of elastic modulus between rock parting and coal to lower the risk of rock burst in STCSRP. (4) The research result was applied to evaluate and control the risk of rock burst occurrence in STCSRP.

Progress of the ECRH Upper Launcher design for ITER

International Nuclear Information System (INIS)

Strauss, D.; Aiello, G.; Bruschi, A.; Chavan, R.; Farina, D.; Figini, L.; Gagliardi, M.; Garcia, V.; Goodman, T.P.; Grossetti, G.; Heemskerk, C.; Henderson, M.A.; Kasparek, W.; Krause, A.; Landis, J.-D.; Meier, A.; Moro, A.; Platania, P.; Plaum, B.; Poli, E.

2014-01-01

The design of the ITER ECRH system provides 20 MW millimeter wave power for central plasma heating and MHD stabilization. The system consists of an array of 24 gyrotrons with power supplies coupled to a set of transmission lines guiding the beams to the four upper and the equatorial launcher. The front steering upper launcher design described herein has passed successfully the preliminary design review, and it is presently in the final design stage. The launcher consists of a millimeter wave system and steering mechanism with neutron shielding integrated into an upper port plug with the plasma facing blanket shield module (in-vessel) and a set of ex-vessel waveguides connecting the launcher to the transmission lines. Part of the transmission lines are the ultra-low loss CVD torus diamond windows and a shutter valve, a miter bend section and the feedthroughs integrated in the plug closure plate. These components are connected by corrugated waveguides and form together the first confinement system (FCS). In-vessel, the millimeter-wave system includes a quasi-optical beam propagation system including four mirror sets and a front steering mirror. The millimeter wave system is integrated into a specifically optimized upper port plug providing structural stability to withstand plasma disruption forces and the high heat load from the plasma side with a dedicated blanket shield module. A recent update in the ITER interface definition has resulted in the recession of the upper port plug first wall panels, which is now integrated into the design. Apart from the millimeter wave system the upper port plug houses also a set of shield blocks which provide neutron shielding. An overview of the actual ITER ECRH Upper Launcher is given together with some highlights of the design

Geology and sratigraphy of the Cainozoic Sedimantary Rocks in the Kale-Kurbalık Area, Denizli, Southwestern Turkey

Directory of Open Access Journals (Sweden)

H.Yavuz HAKYEMEZ

1989-06-01

Full Text Available In this work, the geological and stratigraphical characteristics of the Cainozoic sedimentary rocks exposed at the Kale-Kurbalık (SW Denizli area have been investigated. In the study area the Palaeozoic and Mesozoic rocks form the basement rocks and are overlain by the Oligocene to the Quaternary aged sedimentary rocks. The Tertiary rocks have been considered in two groups, namely the Akçay group and the Muğla group. The Oligocene to the Burdigalian aged Akçay group is represented by the Karadere, Mortuma, Yenidere, Künar and Kale formations. During this time interval, mostly the terrestrial fine and coarse clastics were deposited, but in the last stage of this time shallow marine carbonates were sedimented on the some parts of the region. There is an angular unconformity between the Mortuma and the Yenidere formations of the Akçay group; others are conformable to each other. The Akçay group is 4100 meter thick. The Upper Astarasian (Middle Miocene to Pliocene aged Muğla group which overlies the Akçay group uncorformably is formed of the Sekköy, Yatağan and Milet formations. During this time interval, the lacustrine siltstones and carbonates and the terrestrial coarse elastics were deposited. The formations of the Muğla group are conformable and gradational to each other. The Muğla group is 550 meter thick. The Quaternary deposits have been considered in two units, namely "Lower" and "Upper" Quaternary sediments. Only the Mortuma formation of all units of the study area is gently folded, but others have low degree dips. Tectonic activity has played a big important role in the forming of the various sedimentary basins which have been generated since the beginning of the Oligocene up to the present.

Rollerjaw Rock Crusher

Science.gov (United States)

Peters, Gregory; Brown, Kyle; Fuerstenau, Stephen

2009-01-01

The rollerjaw rock crusher melds the concepts of jaw crushing and roll crushing long employed in the mining and rock-crushing industries. Rollerjaw rock crushers have been proposed for inclusion in geological exploration missions on Mars, where they would be used to pulverize rock samples into powders in the tens of micrometer particle size range required for analysis by scientific instruments.

Range sections as rock models for intensity rock scene segmentation

CSIR Research Space (South Africa)

Mkwelo, S

2007-11-01

Full Text Available This paper presents another approach to segmenting a scene of rocks on a conveyor belt for the purposes of measuring rock size. Rock size estimation instruments are used to monitor, optimize and control milling and crushing in the mining industry...

Qualitative and quantitative changes in detrital reservoir rocks caused by CO2-brine-rock interactions during first injection phases (Utrillas sandstones, northern Spain)

Science.gov (United States)

Berrezueta, E.; Ordóñez-Casado, B.; Quintana, L.

2016-01-01

The aim of this article is to describe and interpret qualitative and quantitative changes at rock matrix scale of lower-upper Cretaceous sandstones exposed to supercritical (SC) CO2 and brine. The effects of experimental injection of CO2-rich brine during the first injection phases were studied at rock matrix scale, in a potential deep sedimentary reservoir in northern Spain (Utrillas unit, at the base of the Cenozoic Duero Basin).Experimental CO2-rich brine was exposed to sandstone in a reactor chamber under realistic conditions of deep saline formations (P ≈ 7.8 MPa, T ≈ 38 °C and 24 h exposure time). After the experiment, exposed and non-exposed equivalent sample sets were compared with the aim of assessing possible changes due to the effect of the CO2-rich brine exposure. Optical microscopy (OpM) and scanning electron microscopy (SEM) aided by optical image analysis (OIA) were used to compare the rock samples and get qualitative and quantitative information about mineralogy, texture and pore network distribution. Complementary chemical analyses were performed to refine the mineralogical information and to obtain whole rock geochemical data. Brine composition was also analyzed before and after the experiment.The petrographic study of contiguous sandstone samples (more external area of sample blocks) before and after CO2-rich brine injection indicates an evolution of the pore network (porosity increase ≈ 2 %). It is probable that these measured pore changes could be due to intergranular quartz matrix detachment and partial removal from the rock sample, considering them as the early features produced by the CO2-rich brine. Nevertheless, the whole rock and brine chemical analyses after interaction with CO2-rich brine do not present important changes in the mineralogical and chemical configuration of the rock with respect to initial conditions, ruling out relevant precipitation or dissolution at these early stages to rock-block scale. These results

Locking screw-plate interface stability in carbon-fibre reinforced polyetheretherketone proximal humerus plates.

Science.gov (United States)

Hak, David J; Fader, Ryan; Baldini, Todd; Chadayammuri, Vivek B S

2017-09-01

Carbon-fibre reinforced polyetheretherketone (CFR-PEEK) plates have recently been introduced for proximal humerus fracture treatment. The purpose of this study was to compare the locking screw-plate interface stability in CFR-PEEK versus stainless steel (SS) proximal humerus plates. Locking screw mechanical stability was evaluated independently in proximal and shaft plate holes. Stiffness and load to failure were tested for three conditions: (1) on-axis locking screw insertion in CFR-PEEK versus SS plates, (2) on-axis locking screw insertion, removal, and reinsertion in CFR-PEEK plates, and (3) 10-degree off-axis locking screw insertion in CFR-PEEK plates. Cantilever bending at a rate of 1 mm/minute was produced by an Instron machine and load-displacement data recorded. Shaft locking screw load to failure was significantly greater in CFR-PEEK plates compared to SS plates (746.4 ± 89.7 N versus 596.5 ± 32.6 N, p PEEK plates (p PEEK plates. The mechanical stability of locking screws in CFR-PEEK plates is comparable or superior to locking screws in SS plates.

Ring complexes and related rocks in Africa

Science.gov (United States)

Vail, J. R.

Over 625 igneous complexes throughout Africa and Arabia have been selected and classified on the basis of petrographic association and chronology into six broad age groups forming 29 provinces. The groups range from Mid-Proterozoic to Tertiary and include gabbro, granite, syenite, foid syenite and carbonatite plutonic rocks, the majority in the form of ring-dykes, cone-sheets, plugs, circular intrusions, and their associated extrusive phases. Pan-African late or post-orogenic complexes (720-490 Ma) are common in the Arabian-Nubian and Tuareg shields of north Africa originating from subduction zone derived magmatism. Anorogenic complexes in Egypt, NE and central Sudan, Niger, Nigeria, Cameroon, Zaïre-Burundi, Malawi, Mozambique, Zimbabwe, Namibia and Angola span 550 to 50 Ma and are dominantly alkali granites and foid syenites. Many groups occur as en-echelon bands within linear arrays, and show migrating centres of intrusion in variable directions. In W. Africa there was a progressive shift of emplacement southwards during early Ordovician to Mid-Cretaceous times. Distribution patterns suggest thatdeep seated features, such as shear zones associated with lithospheric plate movements,controlled melting, and the resultant location of the complexes. Economic mineralization is not widespread in the rocks of the African ring complexes and is mainly restricted to small deposits of Sn, W, F, U and Nb.

Abrasiveness and hardness of rocks of Cretaceous deposits of Chechen-Ingushetiya. Ob abrazivnosti i tverdosti gornykh porod melovykh otlozhenii Checheno-Ingushetii

Energy Technology Data Exchange (ETDEWEB)

Trofimenko, Yu.P.

1981-01-01

Presented are results of studies of the abrasiveness and hardness of core material taken from Upper Cretaceous deposits in the process of drilling deep boreholes in the areas of Chechen-Ingushetiya. Based on the studies it is established that the abrasiveness of rock is mainly influenced by the coarseness of the mineral grains in the rock, their mineralogical composition, and the composition of the cement. Given is a system of clasification of the investigated core material with respect to abrasiveness and hardness.

Voltage-current characteristics of a pin-plate system with different plate configurations

International Nuclear Information System (INIS)

Feng, Zhuangbo; Long, Zhengwei

2013-01-01

In this paper, the voltage-current (V-I) characteristics of a pin-plate system with four types of collection plate configurations are studied experimentally. The collection plates consider a single metal plate, a metal plate with a fly ash cake layer, a metal plate with a clean filter media and a metal plate with a dirty filter media. The results show that the clean filter media has no obvious effect on the V-I characteristics. But the dirty filter media reduces the current density because of its high resistance. The thick fly ash cake layer increase current density because of the anti-corona effect but the increment is not very obvious.

Rock avalanche occurrence in the San Juan province (Argentina): an analysis of their spatial distribution and main forcing factors

Science.gov (United States)

Penna, Ivanna; Tonini, Marj; Vega Orozco, Carmen D.; Longchamp, Céline; Derron, Marc-Henri; Jaboyedoff, Michel

2013-04-01

Rock avalanches are frequent phenomena in the Argentinean Andes and a particular high concentration of these events is observed in the Northwest (~25°S) and in the Central Andes from 30°S until the transition with the Patagonian Andes (~38°S). Tectonic deformation and seismicity are generally proposed as main driving factors, with weather and lithologic conditions playing a subordinate role. From 28°S to 33°S, the subhorizontal subduction of the Nazca plate drives higher shortening rates than in the surrounding areas, and an intense seismicity. Main morphotectonic units in this regions are the Cordillera and Precordillera, separated by the Barreal-Calingasta depression. In the southern central part of the flat subduction area (30°30'°-32°30'S), it is observed high valley incision and maximum local relief of 2900 m, while in the Precordillera main fluvial courses developed in the inter-thrust valleys, where local relief is up to 2400 m. In both mountain ranges, we recognized 34 rock avalanches deposits with volumes up to 0.3 km3. There is no apparent lithologic control on detachments, which involved sedimentary, volcanic and granite rocks, even though ~20% of them were favored by layering orientation. However, about 50% of the inventoried rock avalanches with the greatest volumes, developed along tectonic structures or less than 1 km far from them. The main objective of the present study is to explore the spatial distribution of rock avalanche deposits, and compare it with the instrumental seismicity and landscape conditions by means of statistical tools (e.g. exploratory data analyses, Ripley's K-function). Those analyses allow to highlight the spatial correlation between the geological events. Moreover, to visually display the detected cluster spatial patterns we elaborated kernel density maps. Our findings revealed that most of the rock avalanches show a high spatial aggregation mainly between 31°20'S-31°50'S. Main concentration of bedrock landslides

Elasto-plastic deformation and plate weakening due to normal faulting in the subducting plate along the Mariana Trench

Science.gov (United States)

Zhou, Zhiyuan; Lin, Jian

2018-06-01

We investigated variations in the elasto-plastic deformation of the subducting plate along the Mariana Trench through an analysis of flexural bending and normal fault characteristics together with geodynamic modeling. Most normal faults were initiated at the outer-rise region and grew toward the trench axis with strikes mostly subparallel to the local trench axis. The average trench relief and maximum fault throws were measured to be significantly greater in the southern region (5 km and 320 m, respectively) than the northern and central regions (2 km and 200 m). The subducting plate was modeled as an elasto-plastic slab subjected to tectonic loading at the trench axis. The calculated strain rates and velocities revealed an array of normal fault-like shear zones in the upper plate, resulting in significant faulting-induced reduction in the deviatoric stresses. We then inverted for solutions that best fit the observed flexural bending and normal faulting characteristics, revealing normal fault penetration to depths of 21, 20, and 32 km beneath the seafloor for the northern, central, and southern regions, respectively, which is consistent with the observed depths of the relocated normal faulting earthquakes in the central Mariana Trench. The calculated deeper normal faults of the southern region might lead to about twice as much water being carried into the mantle per unit trench length than the northern and central regions. We further calculated that normal faulting has reduced the effective elastic plate thickness Te by up to 52% locally in the southern region and 33% in both the northern and central regions. The best-fitting solutions revealed a greater apparent angle of the pulling force in the southern region (51-64°) than in the northern (22-35°) and central (20-34°) regions, which correlates with a general southward increase in the seismically-determined dip angle of the subducting slab along the Mariana Trench.

A planet in transition: The onset of plate tectonics on Earth between 3 and 2 Ga?

Directory of Open Access Journals (Sweden)

Kent C. Condie

2018-01-01

Full Text Available Many geological and geochemical changes are recorded on Earth between 3 and 2 Ga. Among the more important of these are the following: (1 increasing proportion of basalts with “arc-like” mantle sources; (2 an increasing abundance of basalts derived from enriched (EM and depleted (DM mantle sources; (3 onset of a Great Thermal Divergence in the mantle; (4 a decrease in degree of melting of the mantle; (5 beginning of large lateral plate motions; (6 appearance of eclogite inclusions in diamonds; (7 appearance and rapid increase in frequency of collisional orogens; (8 rapid increase in the production rate of continental crust as recorded by zircon age peaks; (9 appearance of ophiolites in the geologic record, and (10 appearance of global LIP (large igneous province events some of which correlate with global zircon age peaks. All of these changes may be tied directly or indirectly to cooling of Earth's mantle and corresponding changes in convective style and the strength of the lithosphere, and they may record the gradual onset and propagation of plate tectonics around the planet. To further understand the changes that occurred between 3 and 2 Ga, it is necessary to compare rocks, rock associations, tectonics and geochemistry during and between zircon age peaks. Geochemistry of peak and inter-peak basalts and TTGs needs to be evaluated in terms of geodynamic models that predict the existence of an episodic thermal regime between stagnant-lid and plate tectonic regimes in early planetary evolution.

Experimental results of the consequences of sodium water reactions at the bottom tube plate region of straight tube steam generators

International Nuclear Information System (INIS)

Ruloff, G.

1990-01-01

Experience with sodium water reactions has shown, that the course of such a steam generator accident depends strongly on its place in the steam generator. For the EFR steam generators we have to differentiate between: weld region at the upper tube plate (gas space); bundle region; weld region at the bottom tube plate. This paper describes results of a running tests program simulating the bottom tube plate area. One main part of these tests is the investigation of the influence of wastage protection shrouds between the tubes in the weld region to avoid a fast leak propagation and to give time for leak detection and mastering of the accidents. (author). 10 figs, 2 tabs