WorldWideScience

Sample records for unique test bed

  1. Instrument Thermal Test Bed - A unique two phase test facility

    Science.gov (United States)

    Swanson, Theodore; Didion, Jeffrey

    1991-01-01

    The Instrument Thermal Test Bed (ITTB) is a modular, large-scale test facility which provides a medium for ground testing and flight qualification of spacecraft thermal control components and system configurations. The initial 'shade-down' operations are discussed herein. Operational parameters and performance characteristics were determined and quantified on a preliminary basis. The ITTB was successfully operated at evaporator power loads ranging from 600 W to 9600 W as well as in both capillary pumped and series hybrid pumped modes.

  2. Virtual Test Bed

    Science.gov (United States)

    2016-06-07

    project is to develop a benchmark system for evaluating models for predicting the characteristics of ocean wind waves. SCIENTIFIC OBJECTIVES A...transformation-scale models (i.e. models which treat the physics of waves propagating from offshore areas into the coastline). Each phase is further divided...to be assembled within the virtual test bed. Wind fields for running these tests will be obtained from Oceanweather, Inc. from a separate ONR

  3. Bed bugs evolved unique adaptive strategy to resist pyrethroid insecticides.

    Science.gov (United States)

    Zhu, Fang; Gujar, Hemant; Gordon, Jennifer R; Haynes, Kenneth F; Potter, Michael F; Palli, Subba R

    2013-01-01

    Recent advances in genomic and post-genomic technologies have facilitated a genome-wide analysis of the insecticide resistance-associated genes in insects. Through bed bug, Cimex lectularius transcriptome analysis, we identified 14 molecular markers associated with pyrethroid resistance. Our studies revealed that most of the resistance-associated genes functioning in diverse mechanisms are expressed in the epidermal layer of the integument, which could prevent or slow down the toxin from reaching the target sites on nerve cells, where an additional layer of resistance (kdr) is possible. This strategy evolved in bed bugs is based on their unique morphological, physiological and behavioral characteristics and has not been reported in any other insect species. RNA interference-aided knockdown of resistance associated genes showed the relative contribution of each mechanism towards overall resistance development. Understanding the complexity of adaptive strategies employed by bed bugs will help in designing the most effective and sustainable bed bug control methods.

  4. Torsion testing of bed joints

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg; Pedersen, Carsten Mørk

    2008-01-01

    This paper describes a simple test method for determining the torsion strength of a single bed joint between two bricks and presents results from testing using this test method. The setup for the torsion test is well defined, require minimal preparation of the test specimen and the test can...... be carried out directly in a normal testing machine. The torsion strength is believed to be the most important parameter in out-of-plane resistance of masonry walls subjected to bending about an axis perpendicular to the bed joints. The paper also contains a few test results from bending of small walls about...... an axis perpendicular to the bed joints, which indicate the close connection between these results and results from torsion tests. These characteristics make the torsion strength well suited to act as substitute parameter for the bending strength of masonry about an axis perpendicular to the bed joints....

  5. Torsion testing of bed joints

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg; Pedersen, Carsten Mørk

    2008-01-01

    be carried out directly in a normal testing machine. The torsion strength is believed to be the most important parameter in out-of-plane resistance of masonry walls subjected to bending about an axis perpendicular to the bed joints. The paper also contains a few test results from bending of small walls about...... an axis perpendicular to the bed joints, which indicate the close connection between these results and results from torsion tests. These characteristics make the torsion strength well suited to act as substitute parameter for the bending strength of masonry about an axis perpendicular to the bed joints....

  6. Designing a CR Test bed

    DEFF Research Database (Denmark)

    2014-01-01

    Research on intelligent and reconfigurable wireless systems is in continuous evolution. Nevertheless, in order to fix some keystones, more and more researchers are entering the idea of research-oriented test beds. Unfortunately, it is very difficult for a wide number of research groups to start w...

  7. Designing a CR Test bed

    DEFF Research Database (Denmark)

    2014-01-01

    with their own set up, since the potential costs and efforts could not pay back in term of expected research results. Software Defined Radio solutions offer an easy way to communication researchers for the development of customized research test beds. While several hardware products are commercially available......, the software is most of the times open source and ready to use for third party users. Even though the software solution developers claim complete easiness in the development of custom applications, in reality there are a number of practical hardware and software issues that research groups need to face, before...... inspiration to researchers on how to possibly build their own customized systems....

  8. CERTS Microgrid Laboratory Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Eto, Joe; Lasseter, Robert; Schenkman, Ben; Stevens, John; Klapp, Dave; Volkommer, Harry; Linton, Ed; Hurtado, Hector; Roy, Jean

    2009-06-18

    The objective of the CERTS Microgrid Test Bed project was to enhance the ease of integrating energy sources into a microgrid. The project accomplished this objective by developing and demonstrating three advanced techniques, collectively referred to as the CERTS Microgrid concept, that significantly reduce the level of custom field engineering needed to operate microgrids consisting of generating sources less than 100kW. The techniques comprising the CERTS Microgrid concept are: 1) a method for effecting automatic and seamless transitions between grid-connected and islanded modes of operation, islanding the microgrid's load from a disturbance, thereby maintaining a higher level of service, without impacting the integrity of the utility's electrical power grid; 2) an approach to electrical protection within a limited source microgrid that does not depend on high fault currents; and 3) a method for microgrid control that achieves voltage and frequency stability under islanded conditions without requiring high-speed communications between sources. These techniques were demonstrated at a full-scale test bed built near Columbus, Ohio and operated by American Electric Power. The testing fully confirmed earlier research that had been conducted initially through analytical simulations, then through laboratory emulations,and finally through factory acceptance testing of individual microgrid components. The islanding and resychronization method met all Institute of Electrical and Electronics Engineers Standard 1547 and power quality requirements. The electrical protection system was able to distinguish between normal and faulted operation. The controls were found to be robust under all conditions, including difficult motor starts and high impedance faults. The results from these tests are expected to lead to additional testing of enhancements to the basic techniques at the test bed to improve the business case for microgrid technologies, as well to field

  9. CERTS Microgrid Laboratory Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    ETO, J.; LASSETER, R.; SCHENKMAN, B.; STEVENS, J.; KLAPP, D.; VOLKOMMER, H.; LINTON, E.; HURTADO, H.; ROY, J.

    2010-06-08

    The objective of the CERTS Microgrid Test Bed project was to enhance the ease of integrating energy sources into a microgrid. The project accomplished this objective by developing and demonstrating three advanced techniques, collectively referred to as the CERTS Microgrid concept, that significantly reduce the level of custom field engineering needed to operate microgrids consisting of generating sources less than 100kW. The techniques comprising the CERTS Microgrid concept are: 1 a method for effecting automatic and seamless transitions between grid-connected and islanded modes of operation, islanding the microgrid's load from a disturbance, thereby maintaining a higher level of service, without impacting the integrity of the utility's electrical power grid; 2 an approach to electrical protection within a limited source microgrid that does not depend on high fault currents; and 3 a method for microgrid control that achieves voltage and frequency stability under islanded conditions without requiring high-speed communications between sources.

  10. CERTS Microgrid Laboratory Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Lasseter, R. H.; Eto, J. H.; Schenkman, B.; Stevens, J.; Volkmmer, H.; Klapp, D.; Linton, E.; Hurtado, H.; Roy, J.

    2010-06-08

    CERTS Microgrid concept captures the emerging potential of distributed generation using a system approach. CERTS views generation and associated loads as a subsystem or a 'microgrid'. The sources can operate in parallel to the grid or can operate in island, providing UPS services. The system can disconnect from the utility during large events (i.e. faults, voltage collapses), but may also intentionally disconnect when the quality of power from the grid falls below certain standards. CERTS Microgrid concepts were demonstrated at a full-scale test bed built near Columbus, Ohio and operated by American Electric Power. The testing fully confirmed earlier research that had been conducted initially through analytical simulations, then through laboratory emulations, and finally through factory acceptance testing of individual microgrid components. The islanding and resynchronization method met all Institute of Electrical and Electronics Engineers Standard 1547 and power quality requirements. The electrical protection system was able to distinguish between normal and faulted operation. The controls were found to be robust under all conditions, including difficult motor starts and high impedance faults.

  11. Modular Electric Propulsion Test Bed Aircraft Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An all electric aircraft test bed is proposed to provide a dedicated development environment for the rigorous study and advancement of electrically powered aircraft....

  12. Modular Electric Propulsion Test Bed Aircraft Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A hybrid electric aircraft simulation system and test bed is proposed to provide a dedicated development environment for the rigorous study and advancement of hybrid...

  13. Development of a hover test bed

    Science.gov (United States)

    Williams, Jason Alan

    This research examines the development, validation, and verification of a hover test bed at the Missile Defense Agency's National Hover Test Facility located at the Air Force Research Laboratory on Edwards Air Force Base, California. This work's scope includes the development of a test bed for exoatmospheric kill vehicle testing in an integrated hover test arrangement. The approach involved reactivation of the facility, design of a risk reduction methodology, and vehicle performance verification. Details from a combustion stability issue on the divert engine is investigated, and changing the diameter of the injector reduced a first tangential combustion chamber mode combustion instability from 17.8% to 0.8%.

  14. Cognitive nonlinear radar test-bed

    Science.gov (United States)

    Hedden, Abigail S.; Wikner, David A.; Martone, Anthony; McNamara, David

    2013-05-01

    Providing situational awareness to the warfighter requires radar, communications, and other electronic systems that operate in increasingly cluttered and dynamic electromagnetic environments. There is a growing need for cognitive RF systems that are capable of monitoring, adapting to, and learning from their environments in order to maintain their effectiveness and functionality. Additionally, radar systems are needed that are capable of adapting to an increased number of targets of interest. Cognitive nonlinear radar may offer critical solutions to these growing problems. This work focuses on ongoing efforts at the U.S. Army Research Laboratory (ARL) to develop a cognitive nonlinear radar test-bed. ARL is working toward developing a test-bed that uses spectrum sensing to monitor the RF environment and dynamically change the transmit waveforms to achieve detection of nonlinear targets with high confidence. This work presents the architecture of the test-bed system along with a discussion of its current capabilities and limitations. A brief outlook is presented for the project along with a discussion of a future cognitive nonlinear radar test-bed.

  15. Development of a flexible test-bed for robotics, telemanipulation and servicing research

    Science.gov (United States)

    Davies, Barry F.

    1989-01-01

    The development of a flexible operation test-bed, based around a commercially available ASEA industrial robot is described. The test-bed was designed to investigate fundamental human factors issues concerned with the unique problems of robotic manipulation in the hostile environment of Space.

  16. Morpheus Vertical Test Bed Flight Testing

    Science.gov (United States)

    Hart, Jeremy; Devolites, Jennifer

    2014-01-01

    NASA's Morpheus Project has developed and tested a prototype planetary lander capable of vertical takeoff and landing, that is designed to serve as a testbed for advanced spacecraft technologies. The lander vehicle, propelled by a LOX/Methane engine and sized to carry a 500kg payload to the lunar surface, provides a platform for bringing technologies from the laboratory into an integrated flight system at relatively low cost. Morpheus onboard software is autonomous from ignition all the way through landing, and is designed to be capable of executing a variety of flight trajectories, with onboard fault checks and automatic contingency responses. The Morpheus 1.5A vehicle performed 26 integrated vehicle test flights including hot-fire tests, tethered tests, and two attempted freeflights between April 2011 and August 2012. The final flight of Morpheus 1.5A resulted in a loss of the vehicle. In September 2012, development began on the Morpheus 1.5B vehicle, which subsequently followed a similar test campaign culminating in free-flights at a simulated planetary landscape built at Kennedy Space Center's Shuttle Landing Facility. This paper describes the integrated test campaign, including successes and setbacks, and how the system design for handling faults and failures evolved over the course of the project.

  17. Fluidized Bed Asbestos Sampler Design and Testing

    Energy Technology Data Exchange (ETDEWEB)

    Karen E. Wright; Barry H. O' Brien

    2007-12-01

    A large number of samples are required to characterize a site contaminated with asbestos from previous mine or other industrial operations. Current methods, such as EPA Region 10’s glovebox method, or the Berman Elutriator method are time consuming and costly primarily because the equipment is difficult to decontaminate between samples. EPA desires a shorter and less costly method for characterizing soil samples for asbestos. The objective of this was to design and test a qualitative asbestos sampler that operates as a fluidized bed. The proposed sampler employs a conical spouted bed to vigorously mix the soil and separate fine particulate including asbestos fibers on filters. The filters are then analyzed using transmission electron microscopy for presence of asbestos. During initial testing of a glass prototype using ASTM 20/30 sand and clay fines as asbestos surrogates, fine particulate adhered to the sides of the glass vessel and the tubing to the collection filter – presumably due to static charge on the fine particulate. This limited the fines recovery to ~5% of the amount added to the sand surrogate. A second prototype was constructed of stainless steel, which improved fines recovery to about 10%. Fines recovery was increased to 15% by either humidifying the inlet air or introducing a voltage probe in the air space above the sample. Since this was not a substantial improvement, testing using the steel prototype proceeded without using these techniques. Final testing of the second prototype using asbestos suggests that the fluidized bed is considerably more sensitive than the Berman elutriator method. Using a sand/tremolite mixture with 0.005% tremolite, the Berman elutriator did not segregate any asbestos structures while the fluidized bed segregated an average of 11.7. The fluidized bed was also able to segregate structures in samples containing asbestos at a 0.0001% concentration, while the Berman elutriator method did not detect any fibers at this

  18. Mechanism test bed. Flexible body model report

    Science.gov (United States)

    Compton, Jimmy

    1991-01-01

    The Space Station Mechanism Test Bed is a six degree-of-freedom motion simulation facility used to evaluate docking and berthing hardware mechanisms. A generalized rigid body math model was developed which allowed the computation of vehicle relative motion in six DOF due to forces and moments from mechanism contact, attitude control systems, and gravity. No vehicle size limitations were imposed in the model. The equations of motion were based on Hill's equations for translational motion with respect to a nominal circular earth orbit and Newton-Euler equations for rotational motion. This rigid body model and supporting software were being refined.

  19. Simulation Facilities and Test Beds for Galileo

    Science.gov (United States)

    Schlarmann, Bernhard Kl.; Leonard, Arian

    2002-01-01

    Galileo is the European satellite navigation system, financed by the European Space Agency (ESA) and the European Commission (EC). The Galileo System, currently under definition phase, will offer seamless global coverage, providing state-of-the-art positioning and timing services. Galileo services will include a standard service targeted at mass market users, an augmented integrity service, providing integrity warnings when fault occur and Public Regulated Services (ensuring a continuity of service for the public users). Other services are under consideration (SAR and integrated communications). Galileo will be interoperable with GPS, and will be complemented by local elements that will enhance the services for specific local users. In the frame of the Galileo definition phase, several system design and simulation facilities and test beds have been defined and developed for the coming phases of the project, respectively they are currently under development. These are mainly the following tools: Galileo Mission Analysis Simulator to design the Space Segment, especially to support constellation design, deployment and replacement. Galileo Service Volume Simulator to analyse the global performance requirements based on a coverage analysis for different service levels and degrades modes. Galileo System Simulation Facility is a sophisticated end-to-end simulation tool to assess the navigation performances for a complete variety of users under different operating conditions and different modes. Galileo Signal Validation Facility to evaluate signal and message structures for Galileo. Galileo System Test Bed (Version 1) to assess and refine the Orbit Determination &Time Synchronisation and Integrity algorithms, through experiments relying on GPS space infrastructure. This paper presents an overview on the so called "G-Facilities" and describes the use of the different system design tools during the project life cycle in order to design the system with respect to

  20. Studies on IPTV over IMS test bed

    Directory of Open Access Journals (Sweden)

    K. Sundara Raja Raja Perumal

    2012-09-01

    Full Text Available IMS (IP Multimedia Subsystem is an architecturalframe work which allows the convergence ofWireless, Wire line networks and internet therebyserving the use of a global platform for the deliveryof IP multimedia applications. Thus IMS leads inthe greater support of Next Generation Networks(NGN. The cause for IMS a high level technology’sdesign and origin is mainly for the 3rd GenerationPartnership Projects (3GPP. The intension of thedesign and origin of such a subsystem is to enablethe service providers to create and deliver valueadded services to the users on heterogeneousnetwork. IMS is all about sending data (voice,video, files etc over an instrument using absolutelyany kind of networks. The system has beenconfigured to the real IP of 127.0.0.1 using the opensource tool of OpenIMSCore. IMS has beenconfigured between the hosts using OPEN IMSCORE test bed on an Open Source platform andinitiate the calls between several IMS clients and itsregistration was evaluated. The traffic parametersof SIP IMS parameter has been verified usingWireshark network analyzer.

  1. Studies on IPTV over IMS test bed

    Directory of Open Access Journals (Sweden)

    K. Sundara Raja Raja Perumal

    2012-09-01

    Full Text Available IMS (IP Multimedia Subsystem is an architectural frame work which allows the convergence of Wireless, Wire line networks and internet thereby serving the use of a global platform for the delivery of IP multimedia applications. Thus IMS leads in the greater support of Next Generation Networks (NGN. The cause for IMS a high level technology’s design and origin is mainly for the 3rd Generation Partnership Projects (3GPP. The intension of the design and origin of such a subsystem is to enable the service providers to create and deliver value added services to the users on heterogeneous network. IMS is all about sending data (voice, video, files etc over an instrument using absolutely any kind of networks. The system has been configured to the real IP of 127.0.0.1 using the open source tool of OpenIMSCore. IMS has been configured between the hosts using OPEN IMS CORE test bed on an Open Source platform and initiate the calls between several IMS clients and its registration was evaluated. The traffic parameters of SIP IMS parameter has been verified using Wireshark network analyzer.

  2. IPv6 Test Bed for Testing Aeronautical Applications

    Science.gov (United States)

    Wilkins, Ryan; Zernic, Michael; Dhas, Chris

    2004-01-01

    Aviation industries in United States and in Europe are undergoing a major paradigm shift in the introduction of new network technologies. In the US, NASA is also actively investigating the feasibility of IPv6 based networks for the aviation needs of the United States. In Europe, the Eurocontrol lead, Internet Protocol for Aviation Exchange (iPAX) Working Group is actively investigating the various ways of migrating the aviation authorities backbone infrastructure from X.25 based networks to an IPv6 based network. For the last 15 years, the global aviation community has pursued the development and implementation of an industry-specific set of communications standards known as the Aeronautical Telecommunications Network (ATN). These standards are now beginning to affect the emerging military Global Air Traffic Management (GATM) community as well as the commercial air transport community. Efforts are continuing to gain a full understanding of the differences and similarities between ATN and Internet architectures as related to Communications, Navigation, and Surveillance (CNS) infrastructure choices. This research paper describes the implementation of the IPv6 test bed at NASA GRC, and Computer Networks & Software, Inc. and these two test beds are interface to Eurocontrol over the IPv4 Internet. This research work looks into the possibility of providing QoS performance for Aviation application in an IPv6 network as is provided in an ATN based network. The test bed consists of three autonomous systems. The autonomous system represents CNS domain, NASA domain and a EUROCONTROL domain. The primary mode of connection between CNS IPv6 testbed and NASA and EUROCONTROL IPv6 testbed is initially a set of IPv6 over IPv4 tunnels. The aviation application under test (CPDLC) consists of two processes running on different IPv6 enabled machines.

  3. Test Guideline Methods for Bed Bug Pesticide Products Now Available

    Science.gov (United States)

    EPA’s final test guidelines, 810.3900 - Laboratory Product Performance Testing Methods for Bed Bug Pesticide Products, provides recommendations for the design and execution of laboratory studies to evaluate the performance of pesticide products.

  4. Communications, Navigation, and Network Reconfigurable Test-bed Flight Hardware Compatibility Test S

    Science.gov (United States)

    2010-01-01

    Communications, Navigation, and Network Reconfigurable Test-bed Flight Hardware Compatibility Test Sets and Networks Integration Management Office Testing for the Tracking and Data Relay Satellite System

  5. High Power Fiber Laser Test Bed

    Data.gov (United States)

    Federal Laboratory Consortium — This facility, unique within DoD, power-combines numerous cutting-edge fiber-coupled laser diode modules (FCLDM) to integrate pumping of high power rare earth-doped...

  6. Design requirements for the supercritical water oxidation test bed

    Energy Technology Data Exchange (ETDEWEB)

    Svoboda, J.M.; Valentich, D.J.

    1994-05-01

    This report describes the design requirements for the supercritical water oxidation (SCWO) test bed that will be located at the Idaho National Engineering Laboratory (INEL). The test bed will process a maximum of 50 gph of waste plus the required volume of cooling water. The test bed will evaluate the performance of a number of SCWO reactor designs. The goal of the project is to select a reactor that can be scaled up for use in a full-size waste treatment facility to process US Department of Energy mixed wastes. EG&G Idaho, Inc. will design and construct the SCWO test bed at the Water Reactor Research Test Facility (WRRTF), located in the northern region of the INEL. Private industry partners will develop and provide SCWO reactors to interface with the test bed. A number of reactor designs will be tested, including a transpiring wall, tube, and vessel-type reactor. The initial SCWO reactor evaluated will be a transpiring wall design. This design requirements report identifies parameters needed to proceed with preliminary and final design work for the SCWO test bed. A flow sheet and Process and Instrumentation Diagrams define the overall process and conditions of service and delineate equipment, piping, and instrumentation sizes and configuration Codes and standards that govern the safe engineering and design of systems and guidance that locates and interfaces test bed hardware are provided. Detailed technical requirements are addressed for design of piping, valves, instrumentation and control, vessels, tanks, pumps, electrical systems, and structural steel. The approach for conducting the preliminary and final designs and environmental and quality issues influencing the design are provided.

  7. FY-2015 Methyl Iodide Deep-Bed Adsorption Test Report

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, Nicholas Ray [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony Leroy [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-30

    Nuclear fission produces fission and activation products, including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Deep-bed methyl iodide adsorption testing has continued in Fiscal Year 2015 according to a multi-laboratory methyl iodide adsorption test plan. Updates to the deep-bed test system have also been performed to enable the inclusion of evaporated HNO3 and increased NO2 concentrations in future tests. This report summarizes the result of those activities. Test results showed that iodine adsorption from gaseous methyl iodide using reduced silver zeolite (AgZ) resulted in initial iodine decontamination factors (DFs, ratios of uncontrolled and controlled total iodine levels) under 1,000 for the conditions of the long-duration test performed this year (45 ppm CH3I, 1,000 ppm each NO and NO2, very low H2O levels [3 ppm] in balance air). The mass transfer zone depth exceeded the cumulative 5-inch depth of 4 bed segments, which is deeper than the 2-4 inch depth estimated for the mass transfer zone for adsorbing I2 using AgZ in prior deep-bed tests. The maximum iodine adsorption capacity for the AgZ under the conditions of this test was 6.2% (6.2 g adsorbed I per 100 g sorbent). The maximum Ag utilization was 51%. Additional deep-bed testing and analyses are recommended to (a) expand the data base for methyl iodide adsorption and (b) provide more data for evaluating organic iodide reactions and reaction byproducts for different potential adsorption conditions.

  8. Unique features of a global human ectoparasite identified through sequencing of the bed bug genome

    Science.gov (United States)

    The bed bug, Cimex lectularius, has re-established itself as a ubiquitous human ectoparasite throughout much of the world during the last two decades. This global resurgence is likely linked to increased international travel and commerce and widespread insecticide resistance. Analyses of the C. le...

  9. Space Station thermal test bed status and plans

    Science.gov (United States)

    Brady, Timothy K.

    1988-01-01

    The accomplishments, current status, and future plans of the thermal test bed program for Space Station thermal management are discussed. This program is intended to support the design and development of the thermal control systems for the Space Station. The topics discussed include heat pipe radiator evaluation, modular panel tests, two-phase heat transport, and testing of thermal buses using ammonia as the working fluid.

  10. Developing and evaluating a meeting assistant test bed

    NARCIS (Netherlands)

    Post, W.M.; Lincoln, M.

    2008-01-01

    A test bed has been developed in which participants are tasked to work in simulated, scenario based, projects in which face-to-face and remote meetings of about 45 minutes have to be held. Measures on performance, team factors and remote aspects are automatically collected with electronic questionna

  11. Unique Aspects of Flight Testing Unmanned Aircraft Systems

    Science.gov (United States)

    2010-04-01

    High Altitude Endurance HCI Human Computer Interface INS Inertial Navigation System IR Infrared JITC Joint Interoperability Testing Command...highlighting some of the unique aspects of flight testing unmanned air vehicle systems. It is intended to provide a practical set of guidelines in support of...of unmanned aviation systems, it is especially important that even minor changes to the baseline code be carefully reviewed, and that regression

  12. Deep Bed Iodine Sorbent Testing FY 2011 Report

    Energy Technology Data Exchange (ETDEWEB)

    Nick Soelberg; Tony Watson

    2011-08-01

    Nuclear fission results in the production of fission products (FPs) and activation products that increasingly interfere with the fission process as their concentrations increase. Some of these fission and activation products tend to evolve in gaseous species during used nuclear fuel reprocessing. Analyses have shown that I129, due to its radioactivity, high potential mobility in the environment, and high longevity (half life of 15.7 million years), can require control efficiencies of up to 1,000x or higher to meet regulatory emission limits. Deep-bed iodine sorption testing has been done to evaluate the performance of solid sorbents for capturing iodine in off-gas streams from nuclear fuel reprocessing plants. The objectives of the FY 2011 deep bed iodine sorbent testing are: (1) Evaluate sorbents for iodine capture under various conditions of gas compositions and operating temperature (determine sorption efficiencies, capacities, and mass transfer zone depths); and (2) Generate data for dynamic iodine sorption modeling. Three tests performed this fiscal year on silver zeolite light phase (AgZ-LP) sorbent are reported here. Additional tests are still in progress and can be reported in a revision of this report or a future report. Testing was somewhat delayed and limited this year due to initial activities to address some questions of prior testing, and due to a period of maintenance for the on-line GC. Each test consisted of (a) flowing a synthetic blend of gases designed to be similar to an aqueous dissolver off-gas stream over the sorbent contained in three separate bed segments in series, (b) measuring each bed inlet and outlet gas concentrations of iodine and methyl iodide (the two surrogates of iodine gas species considered most representative of iodine species expected in dissolver off-gas), (c) operating for a long enough time to achieve breakthrough of the iodine species from at least one (preferably the first two) bed segments, and (d) post-test purging

  13. Creation of a Test Bed Environment for Core Java Applications using White Box Testing Approaches

    Directory of Open Access Journals (Sweden)

    Priya R. L

    2012-10-01

    Full Text Available A Test Bed Environment allows for rigorous, transparent, and replicable testing of scientific theories. However, in software development these test beds can be specified hardware and software environment for the application under test. Though the existing open source test bed environments in Integrated Development Environment (IDEs are capable of supporting the development of Java application types, test reports are generated by third party developers. They do not enhance the utility and the performance of the system constructed. Our proposed system, we have created a customized test bed environment for core java application programs used to generate the test case report using generated control flow graph. This can be obtained by developing a new mini compiler with additional features.

  14. Material control system design: Test Bed Nitrate Storage Area (TBNSA)

    Energy Technology Data Exchange (ETDEWEB)

    Clark, G.A.; Da Roza, R.A.; Dunn, D.R.; Sacks, I.J.; Harrison, W.; Huebel, J.G.; Ross, W.N.; Salisbury, J.D.; Sanborn, R.H.; Weissenberger, S.

    1978-05-01

    This report provides an example of a hypothetical Special Nuclear Material (SNM) Safeguard Material Control and Accounting (MC and A) System which will be used as a subject for the demonstration of the Lawrence Livermore Laboratory MC and A System Evaluation Methodology in January 1978. This methodology is to become a tool in the NRC evaluation of license applicant submittals for Nuclear Fuel Cycle facilities. The starting point for this test bed design was the Allied-General Nuclear Services--Barnwell Nuclear Fuel Plant Reprocessing plant as described in the Final Safety Analysis Report (FSAR), of August 1975. The test bed design effort was limited to providing an SNM safeguard system for the plutonium nitrate storage area of this facility. (DLC)

  15. Test Bed For Control Of Optical-Path Lengths

    Science.gov (United States)

    O'Neal, Michael C.; Eldred, Daniel D.; Liu, Dankai; Redding, David C.

    1994-01-01

    Truss structure and ancillary equipment constitute test bed for experiments in methods of controlling lengths of optical paths under conditions of structural vibration and deformation. Accommodates both passive and active methods of control. Experimental control system reduces millimeter-level disturbances in optical path length to nanometers. Developed for control, alignment, and aiming of distributed optical systems on large flexible structures. Test bed includes tower 2.5 meters high with two horizontal arms extending at right angles from its top. Rigidly mounted on massive steel block providing measure of isolation from ground vibrations. Optical motion-compensation system similar to one described previously in NASA Tech Briefs enclosed in flexure-mounted frame, called "trolley," at end of longer horizontal arm.

  16. Initialization and Setup of the Coastal Model Test Bed: STWAVE

    Science.gov (United States)

    2017-01-01

    coastal numerical models . Pertinent data types, including waves, water levels, nearshore currents, bathymetry, and meteorological measurements, are...correlation coefficients, and other statistics can be calculated between the observed data and the model output for any duration of time using the...ERDC/CHL CHETN-I-93 January 2017 Approved for public release; distribution is unlimited. Initialization and Setup of the Coastal Model Test Bed

  17. Cloud Computing Test Bed for NASA Earth Observation

    Science.gov (United States)

    Klene, S. A.; Murphy, K. J.; Fertetta, M.; Law, E.; Wilson, B. D.; Hua, H.; Huang, T.

    2014-12-01

    In order to develop a deeper understanding of utilizing cloud computing technologies for using earth observation data processing a test bed was created to ease access to the technology. Users had expressed concerns about accruing large compute bills by accident while they are learning to use the technology. The test bed is to support NASA efforts such as: Developing a Science Data Service platform to handle big earth data for supporting scalable time and space searches, on-the-fly climatologies, data extraction and data transformation such as data re-gridding. Multi-sensor climate data fusion where users can select, merge and cache variables from multiple sensors to compare data over multiple years. Facilitate rapid prototype efforts to provide an infrastructure so that new development efforts do not need to spend time and effort obtaining a platform. Once successful development is done the application could then scale to very large platform on larger or commercial clouds. Goals of the test bed are: To provide a greater understanding of cloud computing so informed choices can be made on future efforts to handle the over 15 Petabytes of NASA earth science data. Provide an environment where a set of science tools can be developed and reused by multiple earth science disciplines. Develop a Platform as a Service (PaaS) capability for general earth science use. This talk will present the lessons learned from building a community cloud for earth science data.

  18. Phase 2 Methyl Iodide Deep-Bed Adsorption Tests

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    Nuclear fission produces fission products (FPs) and activation products, including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Research, demonstrations, and some reprocessing plant experience have indicated that diatomic iodine can be captured with efficiencies high enough to meet regulatory requirements. Research on the capture of organic iodides has also been performed, but to a lesser extent. Several questions remain open regarding the capture of iodine bound in organic compounds. Deep-bed methyl iodide adsorption testing has progressed according to a multi-laboratory methyl iodide adsorption test plan. This report summarizes the second phase of methyl iodide adsorption work performed according to this test plan using the deep-bed iodine adsorption test system at the Idaho National Laboratory (INL), performed during the second half of Fiscal Year (FY) 2014. Test results continue to show that methyl iodide adsorption using AgZ can achieve total iodine decontamination factors (DFs, ratios of uncontrolled and controlled total iodine levels) above 1,000, until breakthrough occurred. However, mass transfer zone depths are deeper for methyl iodide adsorption compared to diatomic iodine (I2) adsorption. Methyl iodide DFs for the Ag Aerogel test adsorption efficiencies were less than 1,000, and the methyl iodide mass transfer zone depth exceeded 8 inches. Additional deep-bed testing and analyses are recommended to (a) expand the data base for methyl iodide adsorption under various conditions specified in the methyl iodide test plan, and (b) provide more data for evaluating organic iodide reactions and reaction byproducts for different potential adsorption conditions.

  19. CERTS Microgrid Laboratory Test Bed - PIER Final Project Report

    Energy Technology Data Exchange (ETDEWEB)

    Eto, Joseph H.; Eto, Joseph H.; Lasseter, Robert; Schenkman, Ben; Klapp, Dave; Linton, Ed; Hurtado, Hector; Roy, Jean; Lewis, Nancy Jo; Stevens, John; Volkommer, Harry

    2008-07-25

    The objective of the CERTS Microgrid Laboratory Test Bed project was to enhance the ease of integrating small energy sources into a microgrid. The project accomplished this objective by developing and demonstrating three advanced techniques, collectively referred to as the CERTS Microgrid concept, that significantly reduce the level of custom field engineering needed to operate microgrids consisting of small generating sources. The techniques comprising the CERTS Microgrid concept are: 1) a method for effecting automatic and seamless transitions between grid-connected and islanded modes of operation; 2) an approach to electrical protection within the microgrid that does not depend on high fault currents; and 3) a method for microgrid control that achieves voltage and frequency stability under islanded conditions without requiring high-speed communications. The techniques were demonstrated at a full-scale test bed built near Columbus, Ohio and operated by American Electric Power. The testing fully confirmed earlier research that had been conducted initially through analytical simulations, then through laboratory emulations, and finally through factory acceptance testing of individual microgrid components. The islanding and resychronization method met all Institute of Electrical and Electronics Engineers 1547 and power quality requirements. The electrical protections system was able to distinguish between normal and faulted operation. The controls were found to be robust and under all conditions, including difficult motor starts. The results from these test are expected to lead to additional testing of enhancements to the basic techniques at the test bed to improve the business case for microgrid technologies, as well to field demonstrations involving microgrids that involve one or mroe of the CERTS Microgrid concepts.

  20. A Physical Protection Systems Test Bed for International Counter-Trafficking System Development

    Energy Technology Data Exchange (ETDEWEB)

    Stinson, Brad J [ORNL; Kuhn, Michael J [ORNL; Donaldson, Terrence L [ORNL; Richardson, Dave [ORNL; Rowe, Nathan C [ORNL; Younkin, James R [ORNL; Pickett, Chris A [ORNL

    2011-01-01

    Physical protection systems have a widespread impact on the nuclear industry in areas such as nuclear safeguards, arms control, and trafficking of illicit goods (e.g., nuclear materials) across international borders around the world. Many challenges must be overcome in design and deployment of foreign border security systems such as lack of infrastructure, extreme environmental conditions, limited knowledge of terrain, insider threats, and occasional cultural resistance. Successful security systems, whether it be a system designed to secure a single facility or a whole border security system, rely on the entire integrated system composed of multiple subsystems. This test bed is composed of many unique sensors and subsystems, including wireless unattended ground sensors, a buried fiber-optic acoustic sensor, a lossy coaxial distributed sensor, wireless links, pan-tilt-zoom cameras, mobile power generation systems, unmanned aerial vehicles, and fiber-optic-fence intrusion detection systems. A Common Operating Picture software architecture is utilized to integrate a number of these subsystems. We are currently performance testing each system for border security and perimeter security applications by examining metrics such as probability of sense and a qualitative understanding of the sensor s vulnerability of defeat. The testing process includes different soil conditions for buried sensors (e.g., dry, wet, and frozen) and an array of different tests including walking, running, stealth detection, and vehicle detection. Also, long term sustainability of systems is tested including performance differences due to seasonal variations (e.g. summer versus winter, while raining, in foggy conditions). The capabilities of the test bed are discussed. Performance testing results, both at the individual component level and integrated into a larger system for a specific deployment (in situ), help illustrate the usefulness and need for integrated testing facilities to carry out this

  1. Hybrid Test Bed of Wind Electric Generator with Photovoltaic Panels

    Directory of Open Access Journals (Sweden)

    G.D.Anbarasi Jebaselvi

    2014-03-01

    Full Text Available Driven by the increasing costs of power production and decreasing fossil fuel reserves with the addition of global environmental concerns, renewable energy is now becoming significant fraction of total electricity production in the world. Advancements in the field of wind electric generator technology and power electronics help to achieve rapid progress in hybrid power system which mainly involves wind, solar and diesel energy with a good battery back-up. Here the discussion brings about the installation of real time test bed with a small electric generator and dynamic solar panels with battery backups.

  2. A Subsystem Test Bed for Chinese Spectral Radioheliograph

    Science.gov (United States)

    Zhao, An; Yan, Yihua; Wang, Wei

    2014-11-01

    The Chinese Spectral Radioheliograph is a solar dedicated radio interferometric array that will produce high spatial resolution, high temporal resolution, and high spectral resolution images of the Sun simultaneously in decimetre and centimetre wave range. Digital processing of intermediate frequency signal is an important part in a radio telescope. This paper describes a flexible and high-speed digital down conversion system for the CSRH by applying complex mixing, parallel filtering, and extracting algorithms to process IF signal at the time of being designed and incorporates canonic-signed digit coding and bit-plane method to improve program efficiency. The DDC system is intended to be a subsystem test bed for simulation and testing for CSRH. Software algorithms for simulation and hardware language algorithms based on FPGA are written which use less hardware resources and at the same time achieve high performances such as processing high-speed data flow (1 GHz) with 10 MHz spectral resolution. An experiment with the test bed is illustrated by using geostationary satellite data observed on March 20, 2014. Due to the easy alterability of the algorithms on FPGA, the data can be recomputed with different digital signal processing algorithms for selecting optimum algorithm.

  3. A Test-Bed Configuration: Toward an Autonomous System

    Science.gov (United States)

    Ocaña, F.; Castillo, M.; Uranga, E.; Ponz, J. D.; TBT Consortium

    2015-09-01

    In the context of the Space Situational Awareness (SSA) program of ESA, it is foreseen to deploy several large robotic telescopes in remote locations to provide surveillance and tracking services for man-made as well as natural near-Earth objects (NEOs). The present project, termed Telescope Test Bed (TBT) is being developed under ESA's General Studies and Technology Programme, and shall implement a test-bed for the validation of an autonomous optical observing system in a realistic scenario, consisting of two telescopes located in Spain and Australia, to collect representative test data for precursor NEO services. In order to fulfill all the security requirements for the TBT project, the use of a autonomous emergency system (AES) is foreseen to monitor the control system. The AES will monitor remotely the health of the observing system and the internal and external environment. It will incorporate both autonomous and interactive actuators to force the protection of the system (i.e., emergency dome close out).

  4. An electro-dynamic 3-dimensional vibration test bed for engineering testing

    Science.gov (United States)

    Saadatzi, Mohammadsadegh; Saadatzi, Mohammad Nasser; Ahmed, Riaz; Banerjee, Sourav

    2017-04-01

    Primary objective of the work is to design, fabrication and testing of a 3-dimensional Mechanical vibration test bed. Vibration testing of engineering prototype devices in mechanical and industrial laboratories is essential to understand the response of the envisioned model under physical excitation conditions. Typically, two sorts of vibration sources are available in physical environment, acoustical and mechanical. Traditionally, test bed to simulate unidirectional acoustic or mechanical vibration is used in engineering laboratories. However, a device may encounter multiple uncoupled and/or coupled loading conditions. Hence, a comprehensive test bed in essential that can simulate all possible sorts of vibration conditions. In this article, an electrodynamic vibration exciter is presented which is capable of simulating 3-dimensional uncoupled (unidirectional) and coupled excitation, in mechanical environments. The proposed model consists of three electromagnetic shakers (for mechanical excitation). A robust electrical control circuit is designed to regulate the components of the test bed through a self-developed Graphical User Interface. Finally, performance of the test bed is tested and validated using commercially available piezoelectric sensors.

  5. Phase 1 Methyl Iodide Deep-Bed Adsorption Tests

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-08-22

    Nuclear fission results in the production of fission products (FPs) and activation products including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Research, demonstrations, and some reprocessing plant experience have indicated that diatomic iodine can be captured with efficiencies high enough to meet regulatory requirements. Research on the capture of organic iodides has also been performed, but to a lesser extent [Jubin 2012b]. Several questions remain open regarding the capture of iodine bound in organic compounds. Deep-bed methyl iodide adsorption testing has progressed according to a multi-laboratory methyl iodide adsorption test plan. This report summarizes the first phase of methyl iodide adsorption work performed according to this test plan using the deep-bed iodine adsorption test system at the Idaho National Laboratory (INL), performed during Fiscal Year (FY) 2013 and early FY-2014. Testing has been performed to address questions posed in the test plan, and followed the testing outline in the test plan. Tests established detection limits, developed procedures for sample analysis with minimal analytical interferences, and confirmed earlier results that show that the methyl iodide reacts when in contact with the AgZ sorbent, and not significantly in the gas flow upstream of the sorbent. The reaction(s) enable separation of the iodine from the organic moiety, so that the iodine can chemisorb onto the sorbent. The organic moiety can form other compounds, some of which are organic compounds that are detected and can be tentatively identified using GC-FID and GCMS. Test results also show that other gas constituents (NOx and/or H2O) can affect the methyl iodide reactions. With NOx and H2O present in the gas stream, the majority of uncaptured iodine exiting iodine-laden sorbent beds is in the form of I2 or HI, species that

  6. Pilot plant testing of IGT`s two-stage fluidized-bed/cyclonic agglomerating combustor

    Energy Technology Data Exchange (ETDEWEB)

    Rehmat, A.; Mensinger, M.C. [Institute of Gas Technology, Chicago, IL (United States); Richardson, T.L. [Environmental Protection Agency, Cincinnati, OH (United States)

    1993-12-31

    The Institute of Gas Technology (IGT) is conducting a multi-year experimental program to develop and test, through pilot-scale operation, IGT`s two-stage fluidized-bed/cyclonic agglomerating combustor (AGGCOM). The AGGCOM process is based on combining the fluidized-bed agglomeration and gasification technology with the cyclonic combustion technology, both of which have been developed at IGT over many years. AGGCOM is a unique and extremely flexible combustor that can operate over a wide range of conditions in the fluidized-bed first stage from low temperature (desorption) to high temperature (agglomeration), including gasification of high-energy-content wastes. The ACCCOM combustor can easily and efficiently destroy solid, liquid, and gaseous organic wastes, while isolating solid inorganic contaminants within an essentially non-leachable glassy matrix, suitable for disposal in ordinary landfills. Fines elutriated from the first stage are captured by a high-efficiency cyclone and returned to the fluidized bed for ultimate incorporation into the agglomerates. Intense mixing in the second-stage cyclonic combustor ensures high destruction and removal efficiencies (DRE) for organic compounds that may be present in the feed material. This paper presents an overview of the experimental development of the AGGCOM process and progress made to date in designing, constructing, and operating the 6-ton/day AGGCOM pilot plant. Results of the bench-scale tests conducted to determine the operating conditions necessary to agglomerate a soil were presented at the 1991 Incineration Conference. On-site construction of the AGGCOM pilot plant was initiated in August 1992 and completed at the end of March 1993, with shakedown testing following immediately thereafter. The initial tests in the AGGCOM pilot plant will focus on the integrated operation of both stages of the combustor and will be conducted with ``clean`` topsoil.

  7. Savonius wind turbines: Design and testing of unique blade designs

    Science.gov (United States)

    McPherson, Paul B.

    As the idea of implementing alternative energy systems into urbanized areas continues to gain popularity, there is a growing need to improve the efficiency of such systems. Therefore, the purpose of this research was to determine whether or not six unique blade designs, developed by the researcher, would lead to a more efficient vertical axis Savonius wind turbine. This report provides details regarding the study of aerodynamic forces, drag coefficients, and flow characteristics around each blade as well as information pertaining to the assembly and field testing of a turbine. The researcher began by conducting wind tunnel tests and computational fluid dynamic simulations on a single blade with the proposed designs. The data from these experiments was then used to calculate the driving and opposing forces and drag coefficients that would be present when each blade design is used in a fully assembled turbine. Lastly, the researcher determined the theoretical maximum efficiency of each turbine by multiplying the difference between the drag coefficients with the Betz Limit (4/27). Upon analyzing the results, the researcher discovered that the forces that were reported in the CFD analysis were more than double those measured in the wind tunnel. In addition, upon calculating the performance of each blade design when assembled into a full turbine, it was found that the turbines may not perform as well as the researcher initially expected; with only one having an efficiency of greater than 12%. However, because of the differences between the wind tunnel and CFD results, the researcher suggests that further experimentation and analysis needs to be completed to accurately justify the performance calculations.

  8. Summary of Technical Meeting To Compare US/French Approaches for Physical Protection Test Beds

    Energy Technology Data Exchange (ETDEWEB)

    Mack, Thomas Kimball [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Martinez, Ruben [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Thomas, Gerald [National Nuclear Security Administration (NNSA), Washington, DC (United States); Palut, Jean-Michel [French Alternative and Atomic Energy Commission (CEA), Fontenay Aux Roses (France)

    2016-01-01

    In September 2015, representatives of the US Department of Energy/National Nuclear Security Administration, including test bed professionals from Sandia National Laboratories, and representatives of the French Alternative Energies and Atomic Energy Commission participated in a one-week workshop to share best practices in design, organization, operations, utilization, improvement, and performance testing of physical protection test beds. The intended workshop outcomes were to (1) share methods of improving respective test bed methodologies and programs and (2) prepare recommendations for standards regarding creating and operating testing facilities for nations new to nuclear operations. At the workshop, the French and American subject matter experts compared best practices as developed at their respective test bed sites; discussed access delay test bed considerations; and presented the limitations/ constraints of physical protection test beds.

  9. Test results of the optical PAT test bed for satellite laser communications

    Science.gov (United States)

    Sun, Jianfeng; Liu, Liren; Zhou, Yu; Liu, De'an

    2008-08-01

    Satellite laser communication systems offer many advantages such as high data rate, small sized equipment, low consumption electric power and others. Recent successful demonstrations of laser communications have demonstrated the feasibility of some of the key aspects of this technology. Sub-microradian pointing, acquisition, and tracking (PAT) functions are key issue to establish the laser communication system in space. The terminals must perform a series of onground test to evaluate characteristics of The PAT performances before flight test. So an optical dynamical PAT test bed is developed to perform ground test of a laser terminal. In this paper, we detail the separate test and the system test results of the optical dynamical PAT test bed. The test was carried out by auto-collimation method, the precision deflect accuracy, scan accuracy and deflect scan accuracy are obtained.

  10. Reconfigurable Data Communications Packet-Switch Emulation Test Bed Demonstrated

    Science.gov (United States)

    Chu, Pong P.; Jones, Robert E.

    1999-01-01

    The Communications Technology Division at the NASA Lewis Research Center has an ongoing program to develop advanced switching and routing technology concepts for future satellite onboard processing systems. Through a university grant as a part of this research, the Cleveland State University is using a flexible reconfigurable data communications packet switch emulation test bed to investigate packet switching techniques. Because of the switching speed and protocol complexity, implementing a data communications network is a tremendous task. Various alternatives should be carefully studied and evaluated in the development stage so that the optimal system configuration can be obtained and implemented later. Therefore, it is desirable to predict the performance of the network before it is actually constructed. This is especially true in the case of satellite systems. In the past, theoretical analysis, software simulation, and prototyping were used to evaluate performance. However, each method has its drawback. There are basic tradeoffs among accuracy, cost, and required evaluation time. No method is completely satisfactory.

  11. Johnson Space Center's Regenerative Life Support Systems Test Bed

    Science.gov (United States)

    Barta, D. J.; Henninger, D. L.

    1996-01-01

    The Regenerative Life Support Systems (RLSS) Test Bed at NASA's Johnson Space Center is an atmospherically closed, controlled environment facility for human testing of regenerative life support systems using higher plants in conjunction with physicochemical life support systems. The facility supports NASA's Advanced Life Support (ALS) Program. The facility is comprised of two large scale plant growth chambers, each with approximately 11 m^2 growing area. The root zone in each chamber is configurable for hydroponic or solid media plant culture systems. One of the two chambers, the Variable Pressure Growth Chamber (VPGC), is capable of operating at lower atmospheric pressures to evaluate a range of environments that may be used in a planetary surface habitat; the other chamber, the Ambient Pressure Growth Chamber (APGC) operates at ambient atmospheric pressure. The air lock of the VPGC is currently being outfitted for short duration (1 to 15 day) human habitation at ambient pressures. Testing with and without human subjects will focus on 1) integration of biological and physicochemical air and water revitalization systems; 2) effect of atmospheric pressure on system performance; 3) planetary resource utilization for ALS systems, in which solid substrates (simulated planetary soils or manufactured soils) are used in selected crop growth studies; 4) environmental microbiology and toxicology; 5) monitoring and control strategies; and 6) plant growth systems design. Included are descriptions of the overall design of the test facility, including discussions of the atmospheric conditioning, thermal control, lighting, and nutrient delivery systems.

  12. Johnson Space Center's Regenerative Life Support Systems Test Bed.

    Science.gov (United States)

    Barta, D J; Henninger, D L

    1996-01-01

    The Regenerative Life Support Systems (RLSS) Test Bed at NASA's Johnson Space Center is an atmospherically closed, controlled environment facility for human testing of regenerative life support systems using higher plants in conjunction with physicochemical life support systems. The facility supports NASA's Advanced Life Support (ALS) Program. The facility is comprised of two large scale plant growth chambers, each with approximately 11 m2 growing area. The root zone in each chamber is configurable for hydroponic or solid media plant culture systems. One of the two chambers, the Variable Pressure Growth Chamber (VPGC), is capable of operating at lower atmospheric pressures to evaluate a range of environments that may be used in a planetary surface habitat; the other chamber, the Ambient Pressure Growth Chamber (APGC) operates at ambient atmospheric pressure. The air lock of the VPGC is currently being outfitted for short duration (1 to 15 day) human habitation at ambient pressures. Testing with and without human subjects will focus on 1) integration of biological and physicochemical air and water revitalization systems; 2) effect of atmospheric pressure on system performance; 3) planetary resource utilization for ALS systems, in which solid substrates (simulated planetary soils or manufactured soils) are used in selected crop growth studies; 4) environmental microbiology and toxicology; 5) monitoring and control strategies; and 6) plant growth systems design. Included are descriptions of the overall design of the test facility, including discussions of the atmospheric conditioning, thermal control, lighting, and nutrient delivery systems.

  13. Liquid Oxygen/Liquid Methane Integrated Propulsion System Test Bed

    Science.gov (United States)

    Flynn, Howard; Lusby, Brian; Villemarette, Mark

    2011-01-01

    In support of NASA?s Propulsion and Cryogenic Advanced Development (PCAD) project, a liquid oxygen (LO2)/liquid methane (LCH4) Integrated Propulsion System Test Bed (IPSTB) was designed and advanced to the Critical Design Review (CDR) stage at the Johnson Space Center. The IPSTB?s primary objectives are to study LO2/LCH4 propulsion system steady state and transient performance, operational characteristics and to validate fluid and thermal models of a LO2/LCH4 propulsion system for use in future flight design work. Two phase thermal and dynamic fluid flow models of the IPSTB were built to predict the system performance characteristics under a variety of operating modes and to aid in the overall system design work. While at ambient temperature and simulated altitude conditions at the White Sands Test Facility, the IPSTB and its approximately 600 channels of system instrumentation would be operated to perform a variety of integrated main engine and reaction control engine hot fire tests. The pressure, temperature, and flow rate data collected during this testing would then be used to validate the analytical models of the IPSTB?s thermal and dynamic fluid flow performance. An overview of the IPSTB design and analytical model development will be presented.

  14. Lawrence Livermore National Laboratory ULTRA-350 Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, D J; Wulff, T A; Carlisle, K

    2001-04-10

    LLNL has many in-house designed high precision machine tools. Some of these tools include the Large Optics Diamond Turning Machine (LODTM) [1], Diamond Turning Machine No.3 (DTM-3) and two Precision Engineering Research Lathes (PERL-I and PERL-II). These machines have accuracy in the sub-micron range and in most cases position resolution in the couple of nanometers range. All of these machines are built with similar underlying technologies. The machines use capstan drive technology, laser interferometer position feedback, tachometer velocity feedback, permanent magnet (PM) brush motors and analog velocity and position loop servo compensation [2]. The machine controller does not perform any servo compensation it simply computes the differences between the commanded position and the actual position (the following error) and sends this to a D/A for the analog servo position loop. LLNL is designing a new high precision diamond turning machine. The machine is called the ULTRA 350 [3]. In contrast to many of the proven technologies discussed above, the plan for the new machine is to use brushless linear motors, high precision linear scales, machine controller motor commutation and digital servo compensation for the velocity and position loops. Although none of these technologies are new and have been in use in industry, applications of these technologies to high precision diamond turning is limited. To minimize the risks of these technologies in the new machine design, LLNL has established a test bed to evaluate these technologies for application in high precision diamond turning. The test bed is primarily composed of commercially available components. This includes the slide with opposed hydrostatic bearings, the oil system, the brushless PM linear motor, the two-phase input three-phase output linear motor amplifier and the system controller. The linear scales are not yet commercially available but use a common electronic output format. As of this writing, the final

  15. Lawrence Livermore National Laboratory ULTRA-350 Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, D J; Wulff, T A; Carlisle, K

    2001-04-10

    LLNL has many in-house designed high precision machine tools. Some of these tools include the Large Optics Diamond Turning Machine (LODTM) [1], Diamond Turning Machine No.3 (DTM-3) and two Precision Engineering Research Lathes (PERL-1 and PERL-11). These machines have accuracy in the sub-micron range and in most cases position resolution in the couple of nanometers range. All of these machines are built with similar underlying technologies. The machines use capstan drive technology, laser interferometer position feedback, tachometer velocity feedback, permanent magnet (PM) brush motors and analog velocity and position loop servo compensation [2]. The machine controller does not perform any servo compensation it simply computes the differences between the commanded position and the actual position (the following error) and sends this to a D/A for the analog servo position loop. LLNL is designing a new high precision diamond turning machine. The machine is called the ULTRA 350 [3]. In contrast to many of the proven technologies discussed above, the plan for the new machine is to use brushless linear motors, high precision linear scales, machine controller motor commutation and digital servo compensation for the velocity and position loops. Although none of these technologies are new and have been in use in industry, applications of these technologies to high precision diamond turning is limited. To minimize the risks of these technologies in the new machine design, LLNL has established a test bed to evaluate these technologies for application in high precision diamond turning. The test bed is primarily composed of commercially available components. This includes the slide with opposed hydrostatic bearings, the oil system, the brushless PM linear motor, the two-phase input three-phase output linear motor amplifier and the system controller. The linear scales are not yet commercially available but use a common electronic output format. As of this writing, the final

  16. Deep Bed Adsorption Testing using Silver-Functionalized Aerogel

    Energy Technology Data Exchange (ETDEWEB)

    Nick Soelberg; Tony Watson

    2012-06-01

    Nuclear fission results in the production of fission products and activation products, some of which tend to be volatile during used fuel reprocessing and evolve in gaseous species into the reprocessing facility off-gas systems. Analyses have shown that I129, due to its radioactivity, high potential mobility in the environment, and high longevity (half life of 15.7 million years), can require control efficiencies of up to 1,000x or higher to meet regulatory emission limits. Two Aerogel sorption tests that have been performed this fiscal year. The maximum iodine decontamination factor (DF) was measured to be over 10,000, above the 1,000-10,000 target DF range. The mass transfer zone may be as short as 0.5 inches under the sorption conditions of the first test. Only a small fraction of the iodine sorbed on Bed 1 was desorbed during the purge periods. The silver-functionalized Aerogel appears to have potential to be a very effective and efficient iodine sorbent.

  17. Development of a smart-antenna test-bed, demonstrating software defined digital beamforming

    NARCIS (Netherlands)

    Kluwer, T.; Slump, C.H.; Schiphorst, R.; Hoeksema, F.W.

    2001-01-01

    This paper describes a smart-antenna test-bed consisting of ‘common of the shelf’ (COTS) hardware and software defined radio components. The use of software radio components enables a flexible platform to implement and test mobile communication systems as a real-world system. The test-bed is configu

  18. 77 FR 18793 - Spectrum Sharing Innovation Test-Bed Pilot Program

    Science.gov (United States)

    2012-03-28

    ... Pilot Program, 73 FR 76,002 (Dec. 15, 2008). \\3\\ The final Phase I test plan and additional information... National Telecommunications and Information Administration Spectrum Sharing Innovation Test-Bed Pilot... conduct in Phase II/III of the Spectrum Sharing Innovation Test-Bed pilot program to assess...

  19. Iodine Sorbent Performance in FY 2012 Deep Bed Tests

    Energy Technology Data Exchange (ETDEWEB)

    Nick Soelberg; Tony Watson

    2012-08-01

    Nuclear fission results in the production of fission products and activation products, some of which tend to be volatile during used fuel reprocessing and evolve in gaseous species into the reprocessing facility off-gas systems. Analyses have shown that I-129, due to its radioactivity, high potential mobility in the environment, and high longevity (half life of 15.7 million years), can require control efficiencies of up to 1,000x or higher to meet regulatory emission limits. Iodine capture is an important aspect of the Separations and Waste Forms Campaign Off-gas Sigma Team (Jubin 2011, Pantano 2011). Deep-bed iodine sorption tests for both silver-functionalized Aerogel and silver zeolite sorbents were performed during Fiscal Year 2012. These tests showed that: • Decontamination factors were achieved that exceed reasonably conservative estimates for DFs needed for used fuel reprocessing facilities in the U.S. to meet regulatory requirements for I-129 capture. • Silver utilizations approached or exceeded 100% for high inlet gas iodine concentrations, but test durations were not long enough to approach 100% silver utilization for lower iodine concentrations. • The depth of the mass transfer zone was determined for both low iodine concentrations (under 10 ppmv) and for higher iodine concentrations (between 10-50 ppmv); the depth increases over time as iodine is sorbed. • These sorbents capture iodine by chemisorption, where the sorbed iodine reacts with the silver to form very non-volatile AgI. Any sorbed iodine that is physisorbed but not chemically reacted with silver to form AgI might not be tightly held by the sorbent. The portion of sorbed iodine that tends to desorb because it is not chemisorbed (reacted to form AgI) is small, under 1%, for the AgZ tests, and even smaller, under 0.01%, for the silver-functionalized Aerogel.

  20. RELIABILITY OF TEST LANDS TARGETING IN BED-OF-NAILS STYLE TEST FIXTURE

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A systematic, accurate and robust evaluating method for fine pitch printed circuit board (PCB) positioning assessment in testing fixture is developed. Targeting reliability of bed-of-nails tester is successfully evaluated by the 2D pattern transform. Probe offset vector with its Weibull and Gaussian distribution estimates are obtained for further investigation about the causes of misalignment on the basis of a batch tests for same kind of PCBs.

  1. Femoral Test Bed for Impedance Controlled Surgical Instrumentation

    Directory of Open Access Journals (Sweden)

    Christian Brendle

    2012-01-01

    Full Text Available The risk for patients during the standard procedure of revision of cemented artificial hip joints is unsatisfactorily highdue to its high level of invasiveness and limited access to the operative field. To reduce this risk we are developing anImpedance Controlled Surgical Instrumentation (ICOS system, which aims to establish real-time control during a BoneCement (BC milling process. For this, the relationship between the thickness of the BC and its frequency-dependentelectrical impedance is used to estimate the residual BC thickness. The aim is to avoid unintended cutting of boneby detecting the passage of the BC/bone boundary layer by the milling head. In a second step, an estimation of theresidual BC thickness will be used to improve process control. As a first step towards demonstrating the feasibility ofour approach, presented here are experimental studies to characterize the BC permittivity and to describe the process indetail. The results show that the permittivity properties of BC are dominated by its polymethyl methacrylate (PMMAfraction. Thus, PMMA can be used as a substitute for future experiments. Furthermore, a Femoral Test Bed (FTB wasdesigned. Using this setup we show it is feasible to accurately distinguish between slightly different thicknesses of BC.

  2. Multiagency Urban Search Experiment Detector and Algorithm Test Bed

    Science.gov (United States)

    Nicholson, Andrew D.; Garishvili, Irakli; Peplow, Douglas E.; Archer, Daniel E.; Ray, William R.; Swinney, Mathew W.; Willis, Michael J.; Davidson, Gregory G.; Cleveland, Steven L.; Patton, Bruce W.; Hornback, Donald E.; Peltz, James J.; McLean, M. S. Lance; Plionis, Alexander A.; Quiter, Brian J.; Bandstra, Mark S.

    2017-07-01

    In order to provide benchmark data sets for radiation detector and algorithm development, a particle transport test bed has been created using experimental data as model input and validation. A detailed radiation measurement campaign at the Combined Arms Collective Training Facility in Fort Indiantown Gap, PA (FTIG), USA, provides sample background radiation levels for a variety of materials present at the site (including cinder block, gravel, asphalt, and soil) using long dwell high-purity germanium (HPGe) measurements. In addition, detailed light detection and ranging data and ground-truth measurements inform model geometry. This paper describes the collected data and the application of these data to create background and injected source synthetic data for an arbitrary gamma-ray detection system using particle transport model detector response calculations and statistical sampling. In the methodology presented here, HPGe measurements inform model source terms while detector response calculations are validated via long dwell measurements using 2"×4"×16" NaI(Tl) detectors at a variety of measurement points. A collection of responses, along with sampling methods and interpolation, can be used to create data sets to gauge radiation detector and algorithm (including detection, identification, and localization) performance under a variety of scenarios. Data collected at the FTIG site are available for query, filtering, visualization, and download at muse.lbl.gov.

  3. Performance test results for the Eaton dc development power train in an electric test bed vehicle

    Science.gov (United States)

    Crumley, R. L.; Donaldson, M. R.

    1987-09-01

    This report presents the results of the tests performed on a direct current (dc) power train in a test bed vehicle developed by the Eaton Corporation for the U.S. Department of Energy (DOE). The tests were performed by EG and G Idaho, Inc. at the Idaho National Engineering Laboratory (INEL). The purpose of the INEL testing was to provide test results from which an evaluation of the performance capabilities of the Eaton dc power train could be made and compared with other vehicle propulsion systems. The planned tests were primarily oriented toward road testing, chassis dynamometer testing, and associated dynamometer coastdown tests for road loss determination. Range tests of the Eaton dc test bed vehicle using an ALCO 2200 lead acid battery pack, produced ranges of 97 km at 56 km/h (60 miles at 35 mph), 79 km at 72 km/h (49 miles at 45 mph), and 47 km at 88 km/h (29 miles at 55 mph). The corresponding net dc energy consumptions are 135 Wh/km (217 Wh/mile), 145 Wh/km (233 Wh/mile), and 178 Wh/km (287 Wh/mile). The energy consumption for the D-cycle test was 241 Wh/km (387 Wh/mile).

  4. Development of an In-Situ Decommissioning Sensor Network Test Bed for Structural Condition Monitoring - 12156

    Energy Technology Data Exchange (ETDEWEB)

    Zeigler, Kristine E.; Ferguson, Blythe A. [Savannah River National Laboratory, Aiken, South Carolina 29808 (United States)

    2012-07-01

    The Savannah River National Laboratory (SRNL) has established an In Situ Decommissioning (ISD) Sensor Network Test Bed, a unique, small scale, configurable environment, for the assessment of prospective sensors on actual ISD system material, at minimal cost. The Department of Energy (DOE) is presently implementing permanent entombment of contaminated, large nuclear structures via ISD. The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. Validation of ISD system performance models and verification of actual system conditions can be achieved through the development a system of sensors to monitor the materials and condition of the structure. The ISD Sensor Network Test Bed has been designed and deployed to addresses the DOE-Environmental Management Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building at the Savannah River Site. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of groutable thermistors for temperature and moisture monitoring, strain gauges for crack growth monitoring, tilt-meters for settlement monitoring, and a communication system for data collection. Baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment. The Sensor Network Test Bed at SRNL uses COTS sensors on concrete blocks from the outer wall of the P Reactor Building to measure conditions expected to occur in ISD structures. Knowledge and lessons learned gained from installation, testing, and monitoring of the equipment will be applied to sensor installation in a meso-scale test bed at FIU and in future ISD structures. The initial data collected from the sensors

  5. Numerical study of propagation effects in a wireless mesh test bed

    CSIR Research Space (South Africa)

    Lysko, AA

    2008-07-01

    Full Text Available The present layout of the indoor wireless mesh network test-bed build at the Meraka Institute is introduced. This is followed by a description of a numerical electromagnetic model for the complete test-bed, including the coupling and diffraction...

  6. Driver D220.12 DRIVER-test-bed: Architecture, Integration and Orchestration

    OpenAIRE

    Berg, T.W. van den

    2015-01-01

    This deliverable describes the recommended architecture of the DRIVER Test Bed. The architecture description is developed in two iterations identified by the deliverable numbers D22.11 D220.12, and this deliverable concerns the second iteration, with initial and preliminary information on test bed services.

  7. Driver D220.12 DRIVER-test-bed: Architecture, Integration and Orchestration

    NARCIS (Netherlands)

    Berg, T.W. van den

    2015-01-01

    This deliverable describes the recommended architecture of the DRIVER Test Bed. The architecture description is developed in two iterations identified by the deliverable numbers D22.11 D220.12, and this deliverable concerns the second iteration, with initial and preliminary information on test bed s

  8. New grid based test bed environment for carrying out ad-hoc networking experiments

    CSIR Research Space (South Africa)

    Johnson, D

    2006-09-01

    Full Text Available and the third is to do analysis on a real test bed network which has implemented the ad-hoc networking protocol. This paper concerns the third option. Most researchers who have done work on test bed environments have used either indoor Wifi inter-office links...

  9. A Unique test for Hubble's new Solar Arrays

    Science.gov (United States)

    2000-10-01

    In mid-October, a team from the European Space Agency (ESA) and NASA will perform a difficult, never-before-done test on one of the Hubble Space Telescope's new solar array panels. Two of these panels, or arrays, will be installed by astronauts in November 2001, when the Space Shuttle Columbia visits Hubble on a routine service mission. The test will ensure that the new arrays are solid and vibration free before they are installed on orbit. The test will be conducted at ESA's European Space Research and Technology Center (ESTEC) in Noordwijk, The Netherlands. Because of the array's size, the facility's special features, and ESA's longstanding experience with Hubble's solar arrays, ESTEC is the only place in the world the test can be performed. This test is the latest chapter in a longstanding partnership between ESA and NASA on the Hubble Space Telescope. The Large Space Simulator at ESTEC, ESA's world-class test facility, features a huge vacuum chamber containing a bank of extremely bright lights that simulate the Sun's intensity - including sunrise and sunset. By exposing the solar wing to the light and temperature extremes of Hubble's orbit, engineers can verify how the new set of arrays will act in space. Hubble orbits the Earth once every 90 minutes. During each orbit, the telescope experiences 45 minutes of searing sunlight and 45 minutes of frigid darkness. This test will detect any tiny vibrations, or jitters, caused by these dramatic, repeated changes. Even a small amount of jitter can affect Hubble's sensitive instruments and interfere with observations. Hubble's first set of solar arrays experienced mild jitter and was replaced in 1993 with a much more stable pair. Since that time, advances in solar cell technology have led to the development of even more efficient arrays. In 2001, NASA will take advantage of these improvements, by fitting Hubble with a third-generation set of arrays. Though smaller, this new set generates more power than the previous

  10. Effects of head-down bed rest on complex heart rate variability: Response to LBNP testing

    Science.gov (United States)

    Goldberger, Ary L.; Mietus, Joseph E.; Rigney, David R.; Wood, Margie L.; Fortney, Suzanne M.

    1994-01-01

    Head-down bed rest is used to model physiological changes during spaceflight. We postulated that bed rest would decrease the degree of complex physiological heart rate variability. We analyzed continuous heart rate data from digitized Holter recordings in eight healthy female volunteers (age 28-34 yr) who underwent a 13-day 6 deg head-down bed rest study with serial lower body negative pressure (LBNP) trials. Heart rate variability was measured on a 4-min data sets using conventional time and frequency domain measures as well as with a new measure of signal 'complexity' (approximate entropy). Data were obtained pre-bed rest (control), during bed rest (day 4 and day 9 or 11), and 2 days post-bed rest (recovery). Tolerance to LBNP was significantly reduced on both bed rest days vs. pre-bed rest. Heart rate variability was assessed at peak LBNP. Heart rate approximate entropy was significantly decreased at day 4 and day 9 or 11, returning toward normal during recovery. Heart rate standard deviation and the ratio of high- to low-power frequency did not change significantly. We conclude that short-term bed rest is associated with a decrease in the complex variability of heart rate during LBNP testing in healthy young adult women. Measurement of heart rate complexity, using a method derived from nonlinear dynamics ('chaos theory'), may provide a sensitive marker of this loss of physiological variability, complementing conventional time and frequency domain statistical measures.

  11. Newborn car bed testing in a community hospital: implementing the American Academy of Pediatrics recommendations.

    Science.gov (United States)

    Wilker, Richard E; Cotoni, Brenda J; Mirando, Carolyn S; Bass, Joel L

    2014-09-01

    This study was designed to describe our experience in implementing the American Academy of Pediatrics (AAP) recommendation to test infants in a car bed if they fail a car seat challenge test. Car seat challenge testing was performed for 90 minutes or the anticipated duration of the trip home, whichever was longer. Based on the pulse oximetry saturation values (90-92% or bed. Testing took place in both the normal newborn nursery (NBN) and special care nursery (SCN). NBN babies who failed in the car bed were transferred to our SCN for additional assessment and management. A total of 197 infants were tested in car seats out of which 177 (89.8%) passed the test. Of the 20 infants who failed, 16 passed the car bed challenge test on the first attempt and were discharged in those devices. All infants who failed the car bed challenge were NBN patients. Using 93% as the acceptable lower limit of oxygenation we successfully implemented the AAP recommendations for car bed challenge testing in our nursery. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  12. Response of a 2-story test-bed structure for the seismic evaluation of nonstructural systems

    Science.gov (United States)

    Soroushian, Siavash; Maragakis, E. "Manos"; Zaghi, Arash E.; Rahmanishamsi, Esmaeel; Itani, Ahmad M.; Pekcan, Gokhan

    2016-03-01

    A full-scale, two-story, two-by-one bay, steel braced-frame was subjected to a number of unidirectional ground motions using three shake tables at the UNR-NEES site. The test-bed frame was designed to study the seismic performance of nonstructural systems including steel-framed gypsum partition walls, suspended ceilings and fire sprinkler systems. The frame can be configured to perform as an elastic or inelastic system to generate large floor accelerations or large inter story drift, respectively. In this study, the dynamic performance of the linear and nonlinear test-beds was comprehensively studied. The seismic performance of nonstructural systems installed in the linear and nonlinear test-beds were assessed during extreme excitations. In addition, the dynamic interactions of the test-bed and installed nonstructural systems are investigated.

  13. Smart Home Test Bed: Examining How Smart Homes Interact with the Power Grid

    Energy Technology Data Exchange (ETDEWEB)

    2016-11-01

    This fact sheet highlights the Smart Home Test Bed capability at the Energy Systems Integration Facility. The National Renewable Energy Laboratory (NREL) is working on one of the new frontiers of smart home research: finding ways for smart home technologies and systems to enhance grid operations in the presence of distributed, clean energy technologies such as photovoltaics (PV). To help advance this research, NREL has developed a controllable, flexible, and fully integrated Smart Home Test Bed.

  14. Next generation network based carrier ethernet test bed for IPTV traffic

    DEFF Research Database (Denmark)

    Fu, Rong; Berger, Michael Stübert; Zheng, Yu;

    2009-01-01

    This paper presents a Carrier Ethernet (CE) test bed based on the Next Generation Network (NGN) framework. After the concept of CE carried out by Metro Ethernet Forum (MEF), the carrier-grade Ethernet are obtaining more and more interests and being investigated as the low cost and high performance...... services of transport network to carry the IPTV traffic. This test bed is approaching to support the research on providing a high performance carrier-grade Ethernet transport network for IPTV traffic....

  15. Mounted Smartphones as Measurement and Control Platforms for Motor-Based Laboratory Test-Beds

    Science.gov (United States)

    Frank, Jared A.; Brill, Anthony; Kapila, Vikram

    2016-01-01

    Laboratory education in science and engineering often entails the use of test-beds equipped with costly peripherals for sensing, acquisition, storage, processing, and control of physical behavior. However, costly peripherals are no longer necessary to obtain precise measurements and achieve stable feedback control of test-beds. With smartphones performing diverse sensing and processing tasks, this study examines the feasibility of mounting smartphones directly to test-beds to exploit their embedded hardware and software in the measurement and control of the test-beds. This approach is a first step towards replacing laboratory-grade peripherals with more compact and affordable smartphone-based platforms, whose interactive user interfaces can engender wider participation and engagement from learners. Demonstrative cases are presented in which the sensing, computation, control, and user interaction with three motor-based test-beds are handled by a mounted smartphone. Results of experiments and simulations are used to validate the feasibility of mounted smartphones as measurement and feedback control platforms for motor-based laboratory test-beds, report the measurement precision and closed-loop performance achieved with such platforms, and address challenges in the development of platforms to maintain system stability. PMID:27556464

  16. Space Suit Portable Life Support System Test Bed (PLSS 1.0) Development and Testing

    Science.gov (United States)

    Watts, Carly; Campbell, Colin; Vogel, Matthew; Conger, Bruce

    2012-01-01

    A multi-year effort has been carried out at NASA-JSC to develop an advanced extra-vehicular activity Portable Life Support System (PLSS) design intended to further the current state of the art by increasing operational flexibility, reducing consumables, and increasing robustness. Previous efforts have focused on modeling and analyzing the advanced PLSS architecture, as well as developing key enabling technologies. Like the current International Space Station Extra-vehicular Mobility Unit PLSS, the advanced PLSS comprises three subsystems required to sustain the crew during extra-vehicular activity including the Thermal, Ventilation, and Oxygen Subsystems. This multi-year effort has culminated in the construction and operation of PLSS 1.0, a test bed that simulates full functionality of the advanced PLSS design. PLSS 1.0 integrates commercial off the shelf hardware with prototype technology development components, including the primary and secondary oxygen regulators, Ventilation Subsystem fan, Rapid Cycle Amine swingbed carbon dioxide and water vapor removal device, and Spacesuit Water Membrane Evaporator heat rejection device. The overall PLSS 1.0 test objective was to demonstrate the capability of the Advanced PLSS to provide key life support functions including suit pressure regulation, carbon dioxide and water vapor removal, thermal control and contingency purge operations. Supplying oxygen was not one of the specific life support functions because the PLSS 1.0 test was not oxygen rated. Nitrogen was used for the working gas. Additional test objectives were to confirm PLSS technology development components performance within an integrated test bed, identify unexpected system level interactions, and map the PLSS 1.0 performance with respect to key variables such as crewmember metabolic rate and suit pressure. Successful PLSS 1.0 testing completed 168 test points over 44 days of testing and produced a large database of test results that characterize system level

  17. Preparation of a Frozen Regolith Simulant Bed for ISRU Component Testing in a Vacuum Chamber

    Science.gov (United States)

    Klenhenz, Julie; Linne, Diane

    2013-01-01

    In-Situ Resource Utilization (ISRU) systems and components have undergone extensive laboratory and field tests to expose hardware to relevant soil environments. The next step is to combine these soil environments with relevant pressure and temperature conditions. Previous testing has demonstrated how to incorporate large bins of unconsolidated lunar regolith into sufficiently sized vacuum chambers. In order to create appropriate depth dependent soil characteristics that are needed to test drilling operations for the lunar surface, the regolith simulant bed must by properly compacted and frozen. While small cryogenic simulant beds have been created for laboratory tests, this scale effort will allow testing of a full 1m drill which has been developed for a potential lunar prospector mission. Compacted bulk densities were measured at various moisture contents for GRC-3 and Chenobi regolith simulants. Vibrational compaction methods were compared with the previously used hammer compaction, or "Proctor", method. All testing was done per ASTM standard methods. A full 6.13 m3 simulant bed with 6 percent moisture by weight was prepared, compacted in layers, and frozen in a commercial freezer. Temperature and desiccation data was collected to determine logistics for preparation and transport of the simulant bed for thermal vacuum testing. Once in the vacuum facility, the simulant bed will be cryogenically frozen with liquid nitrogen. These cryogenic vacuum tests are underway, but results will not be included in this manuscript.

  18. HER2 Testing in Gastric/Gastroesophageal Junction Adenocarcinomas: Unique Features of a Familiar Test.

    Science.gov (United States)

    Ross, Jeffrey S; Mulcahy, Mary

    2011-03-01

    Using the standard slide-based techniques of immunohistochemistry (IHC) and fluorescence in situ hybridization (FISH), it has been firmly established that human epidermal growth factor receptor 2 (HER2) is overexpressed in adenocarcinoma of the upper gastrointestinal tract. In the ToGA trial, the addition of the monoclonal antibody trastuzumab to a standard regimen of cisplatin and fluoropyrimidine resulted in a clinically and statistically significant benefit in terms of response rate, median progression-free survival, and median overall survival in HER2-positive patients. Major differences exist, however, between HER2 testing in gastric/gastroesophageal junction (GEJ) cancer versus breast cancer, and the ToGA trial employed a significant modification of the breast cancer scoring criteria. As trastuzumab approaches regulatory approval in the United States for gastric/GEJ cancer, it is critical that pathologists and diagnostic laboratories learn and apply the unique criteria for assessing gastric/GEJ tumors for their HER2 status defined by the ToGA investigators, as they ready themselves for the approximately 50,000 new specimens that will be tested for HER2 status by both IHC and FISH each year.

  19. Climate Science for a Sustainable Energy Future Test Bed and Data Infrastructure Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Dean N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Foster, I. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Van Dam, Kerstin Kleese [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shipman, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2014-05-04

    The collaborative Climate Science for a Sustainable Energy Future (CSSEF) project started in July 2011 with the goal of accelerating the development of climate model components (i.e., atmosphere, ocean and sea ice, and land surface) and enhancing their predictive capabilities while incorporating uncertainty quantification (UQ). This effort required accessing and converting observational data sets into specialized model testing and verification data sets and building a model development test bed, where model components and sub-models can be rapidly evaluated. CSSEF’s prototype test bed demonstrated, how an integrated testbed could eliminate tedious activities associated with model development and evaluation, by providing the capability to constantly compare model output—where scientists store, acquire, reformat, regrid, and analyze data sets one-by-one—to observational measurements in a controlled test bed.

  20. Walk on Floor Eyes Closed Test: A Unique Test of Spaceflight Induced Ataxia

    Science.gov (United States)

    Reschke, M. F.; Fisher, E. A.; Kofman, I. S.; Cerisano, J. M.; Harm, D. L.; Bloomberg, J. J.

    2011-01-01

    Measurement and quantification of posture and locomotion following spaceflight is an evolving process. Based on the data obtained from the current investigation we believe that the walk on the floor line test with the eyes closed (WOFEC) provides a unique procedure for quantifying postflight ataxia. As a part of an ongoing investigation designed to look at functional changes in astronauts returning from spaceflight seven astronauts (5 short duration with flights of 12-16 days; 2 long duration crewmembers with flights of 6 months) were tested twice before flight, on landing day (short duration only), and 1, 6, and 30 days after flight. The WOFEC consisted of walking for 10 steps (repeated twice) with the feet heel to toe in tandem, arms folded across the chest and the eyes closed. The performance metric (scored by three examiners from video) was the percentage of correct steps completed over the three trials. A step was not counted as correct if the crewmember side-stepped, opened their eyes, or paused for more than three seconds between steps. The data reveled a significant decrease in percentage of correct steps on landing day (short duration crew) and on the first day following landing (long duration) with partial recovery the following day, and full recovery beginning on day sixth after flight. Both short and long duration fliers appeared to be unaware of foot position relative to their bodies or the floor. Postflight, deviation from a straight path was common, and seemed to be determined by the angle of foot placement relative to their body. While deviation from a straight line could be either left or right, primary deviations were observed to occur to the right. Furthermore, the test for two crewmembers elicited motion sickness symptoms. These data clearly demonstrate the sensorimotor challenges facing crewmembers after returning from spaceflight. The WOFEC test has value providing the investigator or crew surgeon with a simple method to quantify vestibular

  1. An adaptable, low cost test-bed for unmanned vehicle systems research

    Science.gov (United States)

    Goppert, James M.

    2011-12-01

    An unmanned vehicle systems test-bed has been developed. The test-bed has been designed to accommodate hardware changes and various vehicle types and algorithms. The creation of this test-bed allows research teams to focus on algorithm development and employ a common well-tested experimental framework. The ArduPilotOne autopilot was developed to provide the necessary level of abstraction for multiple vehicle types. The autopilot was also designed to be highly integrated with the Mavlink protocol for Micro Air Vehicle (MAV) communication. Mavlink is the native protocol for QGroundControl, a MAV ground control program. Features were added to QGroundControl to accommodate outdoor usage. Next, the Mavsim toolbox was developed for Scicoslab to allow hardware-in-the-loop testing, control design and analysis, and estimation algorithm testing and verification. In order to obtain linear models of aircraft dynamics, the JSBSim flight dynamics engine was extended to use a probabilistic Nelder-Mead simplex method. The JSBSim aircraft dynamics were compared with wind-tunnel data collected. Finally, a structured methodology for successive loop closure control design is proposed. This methodology is demonstrated along with the rest of the test-bed tools on a quadrotor, a fixed wing RC plane, and a ground vehicle. Test results for the ground vehicle are presented.

  2. Intelligent Launch and Range Operations Virtual Test Bed (ILRO-VTB)

    Science.gov (United States)

    Bardina, Jorge; Rajkumar, T.

    2003-01-01

    Intelligent Launch and Range Operations Virtual Test Bed (ILRO-VTB) is a real-time web-based command and control, communication, and intelligent simulation environment of ground-vehicle, launch and range operation activities. ILRO-VTB consists of a variety of simulation models combined with commercial and indigenous software developments (NASA Ames). It creates a hybrid software/hardware environment suitable for testing various integrated control system components of launch and range. The dynamic interactions of the integrated simulated control systems are not well understood. Insight into such systems can only be achieved through simulation/emulation. For that reason, NASA has established a VTB where we can learn the actual control and dynamics of designs for future space programs, including testing and performance evaluation. The current implementation of the VTB simulates the operations of a sub-orbital vehicle of mission, control, ground-vehicle engineering, launch and range operations. The present development of the test bed simulates the operations of Space Shuttle Vehicle (SSV) at NASA Kennedy Space Center. The test bed supports a wide variety of shuttle missions with ancillary modeling capabilities like weather forecasting, lightning tracker, toxic gas dispersion model, debris dispersion model, telemetry, trajectory modeling, ground operations, payload models and etc. To achieve the simulations, all models are linked using Common Object Request Broker Architecture (CORBA). The test bed provides opportunities for government, universities, researchers and industries to do a real time of shuttle launch in cyber space.

  3. JPL control/structure interaction test bed real-time control computer architecture

    Science.gov (United States)

    Briggs, Hugh C.

    1989-01-01

    The Control/Structure Interaction Program is a technology development program for spacecraft that exhibit interactions between the control system and structural dynamics. The program objectives include development and verification of new design concepts - such as active structure - and new tools - such as combined structure and control optimization algorithm - and their verification in ground and possibly flight test. A focus mission spacecraft was designed based upon a space interferometer and is the basis for design of the ground test article. The ground test bed objectives include verification of the spacecraft design concepts, the active structure elements and certain design tools such as the new combined structures and controls optimization tool. In anticipation of CSI technology flight experiments, the test bed control electronics must emulate the computation capacity and control architectures of space qualifiable systems as well as the command and control networks that will be used to connect investigators with the flight experiment hardware. The Test Bed facility electronics were functionally partitioned into three units: a laboratory data acquisition system for structural parameter identification and performance verification; an experiment supervisory computer to oversee the experiment, monitor the environmental parameters and perform data logging; and a multilevel real-time control computing system. The design of the Test Bed electronics is presented along with hardware and software component descriptions. The system should break new ground in experimental control electronics and is of interest to anyone working in the verification of control concepts for large structures.

  4. Develop a generic test-bed for web scraping

    OpenAIRE

    Lorente Adamuz, Pedro

    2015-01-01

    This document contains the description and explanation process developed to construct a Web Scraping Tested. This development has been guided by IGLOR Soluciones Audovisuales Avanzadas S.L. and takes as a reference the project Trenditlive Basic issues of web scraping and the development tools are detailed across the document. [ANGLÈS] Also the design and development of the tool and its consequences are explained form both technical and legal point of view. [CATALÀ] This document contains t...

  5. Thermo-mechanical test rig for experimental evaluation of thermal conductivity of ceramic pebble beds

    Energy Technology Data Exchange (ETDEWEB)

    Lo Frano, Rosa, E-mail: rosa.lofrano@ing.unipi.it; Aquaro, Donato; Pupeschi, Simone; Moscardini, Marigrazia

    2014-10-15

    Highlights: • Thermal conductivity values of bed as function of a material of known conductivity. • Minimizing the error caused by radial heat transfer. • Experimental evaluation of thermal conductivity of alumina pebble at different temperatures. • Experimental test with/without compression load. - Abstract: The experimental determination of mechanical and thermal properties of ceramic pebble beds, such as the lithium orthosilicate or lithium metatitanate, is a key issue in the framework of fusion power technology, for the reason that they are possible candidates in the design of breeder blankets. The paper deals with an experimental method for the evaluation of the thermal conductivity of ceramic pebble beds versus the temperature and compressive strain, based on a steady state heat flux through a material (alumina) of known conductivity. The alumina thermal conductivity is determined by means of the hot wire method. To assess the experimental method, a thermo-mechanical characterization of alumina pebble beds (a material largely available), having different diameters, considering a wide range of temperatures and compression forces has been carried out. Moreover preliminary tests have been performed on lithium orthosilicate and lithium metatitanate pebble beds.

  6. The Design of Impact Test-Bed for High-Flow Water Medium Relief Valve

    Directory of Open Access Journals (Sweden)

    Junliang Chang

    2014-11-01

    Full Text Available Water medium hydraulic systems are widely used in coal mining machinery. As the power of hydraulic system becomes higher, the flow and pressure of water medium relief valve are also higher, and the flow may reach 2000 L/min. However, there is no relevant test-bed which could provide instantaneous high-pressure and high-flow to support the experiment for high-flow relief valve; consequently, this impact test-bed for high-flow water medium relief valve is designed to satisfy fast loading demand. Through building model, simulation analysis, and construction of an impact test-bed of high-flow water medium relief valve, the dynamic performance of high-flow water medium relief valve is detected. The setting pressure of relief valve, the accumulator volume and the filling fluid pressure, and the damping of cartridge valve can be changed, and the dynamic performance of high-flow water medium relief valve under different impact loads is detected. The results show that the designed impact test-bed of high-flow water medium relief valve could provide required high-pressure and high-flow emulsion for the tested water medium relief valve, and it could control the strength of impact load, which is an energy saving, high efficiency, and low cost method.

  7. Gowdy waves as a test-bed for constraint-preserving boundary conditions

    CERN Document Server

    Bona, C

    2010-01-01

    Gowdy waves, one of the standard 'apples with apples' tests, is proposed as a test-bed for constraint-preserving boundary conditions in the non-linear regime. As an illustration, energy-constraint preservation is separately tested in the Z4 framework. Both algebraic conditions, derived from energy estimates, and derivative conditions, deduced from the constraint-propagation system, are considered. The numerical errors at the boundary are of the same order than those at the interior points.

  8. Baltimore WATERS Test Bed -- Quantifying Groundwater in Urban Areas

    Science.gov (United States)

    Welty, C.; Miller, A. J.; Ryan, R. J.; Crook, N.; Kerchkof, T.; Larson, P.; Smith, J.; Baeck, M. L.; Kaushal, S.; Belt, K.; McGuire, M.; Scanlon, T.; Warner, J.; Shedlock, R.; Band, L.; Groffman, P.

    2007-12-01

    The purpose of this project is to quantify the urban water cycle, with an emphasis on urban groundwater, using investigations at multiple spatial scales. The overall study focuses on the 171 sq km Gwynns Falls watershed, which spans an urban to rural gradient of land cover and is part of the Baltimore Ecosystem Study LTER. Within the Gwynns Falls, finer-scale studies focus on the 14.3 sq km Dead Run and its subwatersheds. A coarse-grid MODFLOW model has been set up to quantify groundwater flow magnitude and direction at the larger watershed scale. Existing wells in this urban area are sparse, but are being located through mining of USGS NWIS and local well data bases. Wet and dry season water level synoptics, stream seepage transects, and existing permeability data are being used in model calibration. In collaboration with CUAHSI HMF Geophysics, a regional-scale microgravity survey was conducted over the watershed in July 2007 and will be repeated in spring 2008. This will enable calculation of the change in groundwater levels for use in model calibration. At the smaller spatial scale (Dead Run catchment), three types of data have been collected to refine our understanding of the groundwater system. (1) Multiple bromide tracer tests were conducted along a 4 km reach of Dead Run under low-flow conditions to examine groundwater- surface water exchange as a function of land cover type and stream position in the watershed. The tests will be repeated under higher base flow conditions in early spring 2008. Tracer test data will be interpreted using the USGS OTIS model and results will be incorporated into the MODFLOW model. (2) Riparian zone geophysical surveys were carried out with support from CUAHSI HMF Geophysics to delineate depth to bedrock and the water table topography as a function of distance from the stream channel. Resistivity, ground penetrating radar, and seismic refraction surveys were run in ten transects across and around the stream channels. (3) A finer

  9. Enabling Smart Manufacturing Research and Development using a Product Lifecycle Test Bed.

    Science.gov (United States)

    Helu, Moneer; Hedberg, Thomas

    2015-01-01

    Smart manufacturing technologies require a cyber-physical infrastructure to collect and analyze data and information across the manufacturing enterprise. This paper describes a concept for a product lifecycle test bed built on a cyber-physical infrastructure that enables smart manufacturing research and development. The test bed consists of a Computer-Aided Technologies (CAx) Lab and a Manufacturing Lab that interface through the product model creating a "digital thread" of information across the product lifecycle. The proposed structure and architecture of the test bed is presented, which highlights the challenges and requirements of implementing a cyber-physical infrastructure for manufacturing. The novel integration of systems across the product lifecycle also helps identify the technologies and standards needed to enable interoperability between design, fabrication, and inspection. Potential research opportunities enabled by the test bed are also discussed, such as providing publicly accessible CAx and manufacturing reference data, virtual factory data, and a representative industrial environment for creating, prototyping, and validating smart manufacturing technologies.

  10. Migration to a distributed system architecture at the National Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Hoebelheinrich, R.

    1991-09-01

    This is a study to consider the mission of the Strategic Defense Initiative Organization's National Test Bed (NTB) and the current directions of gigabit networking and distributed computing research and to produce a report describing a 5- to 10-year vision of an NTB computing architecture and migration path to that architecture. 97 refs., 20 figs.

  11. Engineering Tools and Validation Test Beds for New Telecommunication Satellite Multimedia Systems

    Science.gov (United States)

    Foix, V.; Taisant, J.-Ph.; Piau, P.; Thomasson, L.

    2002-01-01

    Satellite telecommunication and broadcasting systems have to adapt to the major evolutions introduced by the emergence of new multimedia services distributed by terrestrial networks. This major adaptation of satellite telecommunication systems implies the use of new technologies and standards, on-board satellites and within the telecommunication ground segment. The deeper interaction between space and ground infrastructures induced by these evolutions also leads to additional system complexity. The definition, design and end-to-end validation of these satellite networks require dedicated engineering tools and validation test beds running the major elements of the telecommunication mission, e.g. on-board and ground equipment implementing the various protocols and algorithms used in the system. Through two programmes called respectively "Atelier Télécom du Futur" and "Multimedia System Validation Test Beds", CNES has been developing since early 2000 an advanced simulation tool and complementary test beds to support engineering activities and cover most of the end-to-end validation needs of these new satellite telecommunication multimedia systems. This communication aims to present the technical objectives, the logic which has led to propose several complementary means, their main characteristics and development status. To end up, the first results provided by these tools and test beds are presented.

  12. Integrated architecture for the assessment of ITS in a test bed

    NARCIS (Netherlands)

    Beckmann, D.; Noort, M. van

    2011-01-01

    The development of Intelligent Transport Systems (ITS) applications relies on the use of test beds, not only to achieve effective costs reductions by discovering flaws during early development stages, but also to evaluate complex effects of the application on its surroundings, in particular on the t

  13. Test-bed’s Development of the Packed Bed with Both Revolution&Rotation’s High Gravity

    Science.gov (United States)

    Zhang, Chongpeng; Dong, Zhiqiang; He, Bianhua

    2017-06-01

    Rotating packed bed is a chemical reactor which used the effect of rotating centrifugal force to be equivalent in the gravity field. To increase the fluid flow time in bed, to extend the controlled process in bed’s reaction and to strengthen the role of influencing factor, a new type of rotating packed bed is proposed in the paper which is running on the revolution platform. Unfortunately, the bad synergy effect of revolution&rotation in packed bed has induced the serious vibration problem. Through optimizing the mass center of packed bed and disposing local weight, the stability of the operation of the bench was more improved. The stability of the operation of the bench was that more improved the bed’s vibration amplitude was analyzed by using the ANSYS. The results show that the test-bed of both the Revolution&Rotation’s Packed bed is a practical project in the Rotating packed bed’s development.

  14. Existence and uniqueness of dynamic evolutions for a peeling test in dimension one

    Science.gov (United States)

    Dal Maso, Gianni; Lazzaroni, Giuliano; Nardini, Lorenzo

    2016-11-01

    In this paper we present a one-dimensional model of a dynamic peeling test for a thin film, where the wave equation is coupled with a Griffith criterion for the propagation of the debonding front. Our main results provide existence and uniqueness for the solution to this coupled problem under different assumptions on the data.

  15. A PC-based Flexible Solution for Virtual Instrumentation of a Multi-Purpose Test Bed

    Directory of Open Access Journals (Sweden)

    Benatzky Christian

    2006-11-01

    Full Text Available The aim of the paper is to give an overview of a test bed set up for lightweight flexible structures. The purpose of the test bed is to compare different concepts for suppressing structural vibrations. It is demonstrated that such a complex measurement and actuation task can be easily implemented on a single PC using standard software like Matlab/SIMULINK® with a minimum of custom hardware. With the help of this PC standard engineering tasks like measuring, identification of transfer functions, as well as controller design and implementation in soft real-time can be carried out easily (rapid prototyping. The resulting system is flexible and scalable, enabling an engineer to perform all the above mentioned tasks for a given test object within minimum time. Additionally, the utilization of Matlab/SIMULINK® facilitates the realization of a versatile virtual instrumentation system which is easy to use and may also be remote-controlled.

  16. Social marketing's unique contribution to mental health stigma reduction and HIV testing: two case studies.

    Science.gov (United States)

    Thackeray, Rosemary; Keller, Heidi; Heilbronner, Jennifer Messenger; Dellinger, Laura K Lee

    2011-03-01

    Since its inception in 2005, articles in Health Promotion Practice's social marketing department have focused on describing social marketing's unique contributions and the application of each to the practice of health promotion. This article provides a brief review of six unique features (marketing mix, consumer orientation, segmentation, exchange, competition, and continuous monitoring) and then presents two case studies-one on reducing stigma related to mental health and the other a large-scale campaign focused on increasing HIV testing among African American youth. The two successful case studies show that social marketing principles can be applied to a wide variety of topics among various population groups.

  17. Implementation of a RPS Cyber Security Test-bed with Two PLCs

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Jinsoo; Heo, Gyunyoung [Kyung Hee Univ., Yongin (Korea, Republic of); Son, Hanseong [Joongbu Univ., Geumsan (Korea, Republic of); An, Yongkyu; Rizwan, Uddin [University of Illinois at Urbana-Champaign, Urbana (United States)

    2015-10-15

    Our research team proposed the methodology to evaluate cyber security with Bayesian network (BN) as a cyber security evaluation model and help operator, licensee, licensor or regulator in granting evaluation priorities. The methodology allowed for overall evaluation of cyber security by considering architectural aspect of facility and management aspect of cyber security at the same time. In order to emphasize reality of this model by inserting true data, it is necessary to conduct a penetration test that pretends an actual cyber-attack. Through the collaboration with University of Illinois at Urbana-Champaign, which possesses the Tricon a safety programmable logic controller (PLC) used at nuclear power plants and develops a test-bed for nuclear power plant, a test-bed for reactor protection system (RPS) is being developed with the PLCs. Two PLCs are used to construct a simple test-bed for RPS, bi-stable processor (BP) and coincidence processor (CP). By using two PLCs, it is possible to examine cyber-attack against devices such as PLC, cyber-attack against communication between devices, and the effects of a PLC on the other PLC. Two PLCs were used to construct a test-bed for penetration test in this study. Advantages of using two or more PLCs instead of single PLC are as follows. 1) Results of cyber-attack reflecting characteristics among PLCs can be obtained. 2) Cyber-attack can be attempted using a method of attacking communication between PLCs. True data obtained can be applied to existing cyber security evaluation model to emphasize reality of the model.

  18. Unique Testing Capabilities of the NASA Langley Transonic Dynamics Tunnel, an Exercise in Aeroelastic Scaling

    Science.gov (United States)

    Ivanco, Thomas G.

    2013-01-01

    NASA Langley Research Center's Transonic Dynamics Tunnel (TDT) is the world's most capable aeroelastic test facility. Its large size, transonic speed range, variable pressure capability, and use of either air or R-134a heavy gas as a test medium enable unparalleled manipulation of flow-dependent scaling quantities. Matching these scaling quantities enables dynamic similitude of a full-scale vehicle with a sub-scale model, a requirement for proper characterization of any dynamic phenomenon, and many static elastic phenomena. Select scaling parameters are presented in order to quantify the scaling advantages of TDT and the consequence of testing in other facilities. In addition to dynamic testing, the TDT is uniquely well-suited for high risk testing or for those tests that require unusual model mount or support systems. Examples of recently conducted dynamic tests requiring unusual model support are presented. In addition to its unique dynamic test capabilities, the TDT is also evaluated in its capability to conduct aerodynamic performance tests as a result of its flow quality. Results of flow quality studies and a comparison to a many other transonic facilities are presented. Finally, the ability of the TDT to support future NASA research thrusts and likely vehicle designs is discussed.

  19. Hydrologic properties of coal-beds in the Powder River Basin, Montana. II. Aquifer test analysis

    Science.gov (United States)

    Weeks, E.P.

    2005-01-01

    A multiple well aquifer test to determine anisotropic transmissivity was conducted on a coal-bed in the Powder River Basin, southeastern Montana, as part of a multidisciplinary investigation to determine hydrologic conditions of coal-beds in the area. For the test, three wells were drilled equidistant from and at different angles to a production well tapping the Flowers-Goodale coal seam, a 7.6-m thick seam confined at a depth of about 110 m. The test was conducted by air-lift pumping for 9 h, and water levels were monitored in the three observation wells using pressure transducers. Drawdown data collected early in the test were affected by interporosity flow between the coal fracture network and the matrix, but later data were suitable to determine aquifer anisotropy, as the slopes of the late-time semilog time-drawdown curves are nearly identical, and the zero-drawdown intercepts are different. The maximum transmissivity, trending N87??E, is 14.9 m2/d, and the minimum transmissivity 6.8 m2/d, giving an anisotropy ratio of 2.2:1. Combined specific storage of the fractures and matrix is 2??10 -5/m, and of the fracture network alone 5??10-6/m. The principal direction of the anisotropy tensor is not aligned with the face cleats, but instead is aligned with another fracture set and with dominant east-west tectonic compression. Results of the test indicate that the Flowers-Goodale coal-bed is more permeable than many coals in the Powder River Basin, but the anisotropy ratio and specific storage are similar to those found for other coal-beds in the basin.

  20. Rigging Test Bed Development for Validation of Multi-Stage Decelerator Extractions

    Science.gov (United States)

    Kenig, Sivan J.; Gallon, John C.; Adams, Douglas S.; Rivellini, Tommaso P.

    2013-01-01

    The Low Density Supersonic Decelerator project is developing new decelerator systems for Mars entry which would include testing with a Supersonic Flight Dynamics Test Vehicle. One of the decelerator systems being developed is a large supersonic ringsail parachute. Due to the configuration of the vehicle it is not possible to deploy the parachute with a mortar which would be the preferred method for a spacecraft in a supersonic flow. Alternatively, a multi-stage extraction process using a ballute as a pilot is being developed for the test vehicle. The Rigging Test Bed is a test venue being constructed to perform verification and validation of this extraction process. The test bed consists of a long pneumatic piston device capable of providing a constant force simulating the ballute drag force during the extraction events. The extraction tests will take place both inside a high-bay for frequent tests of individual extraction stages and outdoors using a mobile hydraulic crane for complete deployment tests from initial pack pull out to canopy extraction. These tests will measure line tensions and use photogrammetry to track motion of the elements involved. The resulting data will be used to verify packing and rigging as well, as validate models and identify potential failure modes in order to finalize the design of the extraction system.

  1. Test Bed for Safety Assessment of New e-Navigation Systems

    Directory of Open Access Journals (Sweden)

    Axel Hahn

    2014-12-01

    Full Text Available New e-navigation strains require new technologies, new infrastructures and new organizational structures on bridge, on shore as well as in the cloud. Suitable engineering and safety/risk assessment methods facilitate these efforts. Understanding maritime transportation as a sociotechnical system allows the application of system-engineering methods. Formal, simulation based and in situ verification and validation of e-navigation technologies are important methods to obtain system safety and reliability. The modelling and simulation toolset HAGGIS provides methods for system specification and formal risk analysis. It provides a modelling framework for processes, fault trees and generic hazard specification and a physical world and maritime traffic simulation system. HAGGIS is accompanied by the physical test bed LABSKAUS which implements a physical test bed. The test bed provides reference ports and waterways in combination with an experimental Vessel Traffic Services (VTS system and a mobile integrated bridge: This enables in situ experiments for technological evaluation, testing, ground research and demonstration. This paper describes an integrated seamless approach for developing new e-navigation technologies starting with simulation based assessment and ending in physical real world demonstrations

  2. Space station common module thermal management: Design and construction of a test bed

    Science.gov (United States)

    Barile, R. G.

    1986-01-01

    In this project, a thermal test bed was designed, simulated, and planned for construction. The thermal system features interior and exterior thermal loads and interfacing with the central-radiator thermal bus. Components of the test bed include body mounted radiator loop with interface heat exchangers (600 Btu/hr); an internal loop with cabin air-conditioning and cold plates (3400 Btu/hr); interface heat exchangers to the central bus (13,000 Btu/hr); and provisions for new technology including advanced radiators, thermal storage, and refrigeration. The apparatus will be mounted in a chamber, heated with lamps, and tested in a vacuum chamber with LN2-cooled walls. Simulation of the test bed was accomplished using a DEC PRO 350 computer and the software package TK! olver. Key input variables were absorbed solar radiation and cold plate loads. The results indicate temperatures on the two loops will be nominal when the radiation and cold plate loads are in the range of 25% to 75% of peak loads. If all loads fall to zero, except the cabin air system which was fixed, the radiator fluid will drop below -100 F and may cause excessive pressure drop. If all loads reach 100%, the cabin air temperature could rise to 96 F.

  3. A Method to Analyze Threats and Vulnerabilities by Using a Cyber Security Test-bed of an Operating NPP

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yong Sik; Son, Choul Woong; Lee, Soo Ill [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    In order to implement cyber security controls for an Operating NPP, a security assessment should conduct in advance, and it is essential to analyze threats and vulnerabilities for a cyber security risk assessment phase. It might be impossible to perform a penetration test or scanning for a vulnerability analysis because the test may cause adverse effects on the inherent functions of ones. This is the reason why we develop and construct a cyber security test-bed instead of using real I and C systems in the operating NPP. In this paper, we propose a method to analyze threats and vulnerabilities of a specific target system by using a cyber security test-bed. The test-bed is being developed considering essential functions of the selected safety and non-safety system. This paper shows the method to analyze threats and vulnerabilities of a specific target system by using a cyber security test-bed. In order to develop the cyber security test-bed with both safety and non-safety functions, test-bed functions analysis and preliminary threats and vulnerabilities identification have been conducted. We will determine the attack scenarios and conduct the test-bed based vulnerability analysis.

  4. Two phase capillary pumped heat transfer in the Instrument Thermal Test Bed

    Science.gov (United States)

    Didion, Jeffrey R.; Martins, Mario S.

    1992-01-01

    An experimental study of the thermal performance of two evaporators installed in the Instrument Thermal Test Bed (ITTB) was conducted. The ITTB was operated as a capillary pumped loop (CPL) with a transport length of approximately 12 meters. Empirical determinations of a general start up procedure, overall heat transfer coefficient, and minimum operating power were accomplished for each evaporator. Additionally, a detailed thermal model was developed for the High Power Spacecraft Thermal Management (HPSTM) evaporator and validated.

  5. Fixed-bed gasifier and cleanup system engineering summary report through Test Run No. 100

    Energy Technology Data Exchange (ETDEWEB)

    Pater, K. Jr.; Headley, L.; Kovach, J.; Stopek, D.

    1984-06-01

    The state-of-the-art of high-pressure, fixed-bed gasification has been advanced by the many refinements developed over the last 5 years. A novel full-flow gas cleanup system has been installed and tested to clean coal-derived gases. This report summarizes the results of tests conducted on the gasifier and cleanup system from its inception through 1982. Selected process summary data are presented along with results from complementary programs in the areas of environmental research, process simulation, analytical methods development, and component testing. 20 references, 32 figures, 42 tables.

  6. Low cost test bed tool development for validation of mission control events

    Science.gov (United States)

    Montanez, L.; Cervantes, D.; Tatge, L.

    2003-01-01

    The Cassini Program is one of the last large interplanetary spacecraft missions. It is a joint effort between the European Space Agency, the Italian Space Agency and NASA.The U.S. portion of the mission is managed for NASA by the Jet Propulsion Laboratory (JPL). The primary mission is to survey the complex Saturnian system and release the ESA-Huygens probe at Titan. The success of the Cassini Mission has been largely due its many simulation test beds and its rigorous test program.

  7. Parametric experimental tests of steam gasification of pine wood in a fluidized bed reactor

    Directory of Open Access Journals (Sweden)

    L. Vecchione

    2013-09-01

    Full Text Available Among Renewable Energy Sources (RES, biomass represent one of the most common and suitable solution in order to contribute to the global energy supply and to reduce greenhouse gases (GHG emissions. The disposal of some residual biomass, as pruning from pine trees, represent a problem for agricultural and agro-industrial sectors. But if the residual biomass are used for energy production can become a resource. The most suitable energy conversion technology for the above-mentioned biomass is gasification process because the high C/N ratio and the low moisture content, obtained from the analysis. In this work a small-pilot bubbling-bed gasification plant has been designed, constructed and used in order to obtain, from the pine trees pruning, a syngas with low tar and char contents and high hydrogen content. The activities showed here are part of the activities carried out in the European 7FP UNIfHY project. In particular the aim of this work is to develop experimental test on a bench scale steam blown fluidized bed biomass gasifier. These tests will be utilized in future works for the simulations of a pilot scale steam fluidized bed gasifier (100 kWth fed with different biomass feedstock. The results of the tests include produced gas and tar composition as well gas, tar and char yield. Tests on a bench scale reactor (8 cm I.D. were carried out varying steam to biomass ratio from 0.5, 0.7 and 1 to 830°C.

  8. DARPA Antibody Technology Program Standardized Test Bed for Antibody Characterization: Characterization of an MS2 Human IgG Antibody Produced by AnaptysBio, Inc.

    Science.gov (United States)

    2016-02-01

    ECBC-TR-1339 DARPA ANTIBODY TECHNOLOGY PROGRAM STANDARDIZED TEST BED FOR ANTIBODY...CHARACTERIZATION: CHARACTERIZATION OF AN MS2 HUMAN IGG ANTIBODY PRODUCED BY ANAPTYSBIO, INC. DARPA ATP Standardized Test Bed for Antibody...Characterization: Characterization of an MS2 human IgG antibody produced by AnaptysBio DARPA ATP Standardized Test Bed for Antibody

  9. Design and experimental performance verification of a thermal property test-bed for lunar drilling exploration

    Institute of Scientific and Technical Information of China (English)

    Zhang Tao; Zhao Zeng; Liu Shuting; Li Jinglin; Ding Xilun; Yin Shen; Wang Guoxin; Lai Xiaoming

    2016-01-01

    Chinese Chang’e lunar exploration project aims to collect and return subsurface lunar soil samples at a minimum penetration depth of 2 m in 2017. However, in contrast to those on the Earth, automated drilling and sampling missions on the Moon raise the risk of burning bits. Test-beds are required for testing the thermal properties of drill tools in a lunar environment. In this paper, a novel temperature measuring method based on thermocouples and a slip ring was proposed. Furthermore, a data acquisition system for a drilling process was designed. A vacuous, cryogenic, and anhydrous soil environment simulating the lunar surface was established. A drilling test-bed that can reach a depth of 2.2 m was developed. A control strategy based on online monitoring signals was proposed to improve the drilling performance. Vacuum and non-vacuum experiments were performed to test the temperature rising effect on drill tools. When compared with the non-vacuum experiment, the vacuum temperature rise resulted in a 12 ?C increase. These experimental results provide significant support for Chinese lunar exploration missions.

  10. Unique hue judgments as a function of test size in the fovea and at 20-deg temporal eccentricity

    Science.gov (United States)

    Nerger, Janice L.; Volbrecht, Vicki J.; Ayde, Corey J.

    1995-06-01

    Unique hue loci were measured for four observers in the fovea and at 20-deg temporal eccentricity as a function of test size. Eccentric measurements were made on the cone plateau following a rod bleach. The results indicate that unique yellow remains approximately invariant with respect to test size and retinal eccentricity, whereas unique blue and unique green shift to longer wavelengths with increasing test size. The locus of unique blue in the periphery reaches an asymptote at approximately the same wavelength as that from the foveal measurements, whereas unique green measured in the periphery is consistently at shorter wavelengths than in the fovea. In general, the data are best described by a model in which the short-wavelength-sensitive cone input to the two opponent-color channels decreases with decreasing test size and increasing retinal eccentricity.

  11. A Framework to Evaluate Unified Parameterizations for Seasonal Prediction: An LES/SCM Parameterization Test-Bed

    Science.gov (United States)

    2013-09-30

    Seasonal Prediction: An LES/ SCM Parameterization Test-Bed Joao Teixeira Jet Propulsion Laboratory California Institute of Technology, MS 169-237...a Single Column Model ( SCM ) version of the latest operational NAVGEM that can be used to simulate GEWEX Cloud Systems Study (GCSS) case-studies; ii...use the NAVGEM SCM and the LES model as a parameterization test-bed. APPROACH It is well accepted that sub-grid physical processes such as

  12. Technical scheme and corresponding experiment for the PAT performance of a lasercom using an integrated test-bed

    Science.gov (United States)

    Sun, Jianfeng; Liu, Liren; Wang, Lijuan; Luan, Zhu; Liu, De'an; Xu, Nan; Zhong, Xianghong

    2007-09-01

    Recent successful demonstrations of laser communications have demonstrated the feasibility of some of the key aspects of this technology. The demonstrations can not success without the full-up ground test and validation. So an integrate test-bed was build in build to test the technical parameters and to verify the working performance for the optical pointing, acquisition and tracking (PAT) of various inter-satellite lasercom terminals. In this paper, we detail the test technical scheme (TTS) and the corresponding experiments. The integrate test-bed is a high quality optical system that will measure the key characteristics of lasercom terminals, such as point error, tracking error, acquisition possibility etc.. The test-bed can operate over the relative wavelength range. Through quantitative tests, the terminal could be optimized base on the test results.

  13. Quadrupolar gravitational radiation as a test-bed for f(R)-gravity

    CERN Document Server

    De Laurentis, Mariafelicia

    2011-01-01

    The debate concerning the viability of f(R)-gravity as a natural extension of General Relativity could be realistically addressed by using results coming from binary pulsars like PSR 1913+16. To this end, we develop a quadrupolar approach to the gravitational radiation for a class of ana- lytic f(R)-models. We show that experimental results are compatible with a consistent range of f(R)-models. This means that f(R)-gravity is not ruled out by the observations and gravitational radiation (in strong field regime) could be a test-bed for such theories.

  14. Test-bed Assessment of Communication Technologies for a Power-Balancing Controller

    DEFF Research Database (Denmark)

    Findrik, Mislav; Pedersen, Rasmus; Hasenleithner, Eduard

    2016-01-01

    Due to growing need for sustainable energy, increasing number of different renewable energy resources are being connected into distribution grids. In order to efficiently manage a decentralized power generation units, the smart grid will rely on communication networks for information exchange...... and control. In this paper, we present a Smart Grid test-bed that integrates various communication technologies and deploys a power balancing controller for LV grids. Control performance of the introduced power balancing controller is subsequently investigated and its robustness to communication network cross......-traffic is evaluated. Various scenarios are demonstrated, assessing impact of communication network performance on quality of control....

  15. Modal Analysis on the Wind Tunnel Test Bed based on Workbench

    Directory of Open Access Journals (Sweden)

    Shao Zi-yan

    2015-01-01

    Full Text Available This paper shows a wind tunnel test bed with parallelogram structure. The three-dimensional model was built by Solidworks after analyzing the movement principle. Then the model was imported to Workbench and carried out modal analysis according to the theory of finite element modal analysis. Finally the first six vibration mode and the natural frequency were got. This result provides theoretical support for the further research of the stability of the structure, and it also provides theoretical basis for the optimal design of the institution.

  16. A low-cost test-bed for real-time landmark tracking

    Science.gov (United States)

    Csaszar, Ambrus; Hanan, Jay C.; Moreels, Pierre; Assad, Christopher

    2007-04-01

    A low-cost vehicle test-bed system was developed to iteratively test, refine and demonstrate navigation algorithms before attempting to transfer the algorithms to more advanced rover prototypes. The platform used here was a modified radio controlled (RC) car. A microcontroller board and onboard laptop computer allow for either autonomous or remote operation via a computer workstation. The sensors onboard the vehicle represent the types currently used on NASA-JPL rover prototypes. For dead-reckoning navigation, optical wheel encoders, a single axis gyroscope, and 2-axis accelerometer were used. An ultrasound ranger is available to calculate distance as a substitute for the stereo vision systems presently used on rovers. The prototype also carries a small laptop computer with a USB camera and wireless transmitter to send real time video to an off-board computer. A real-time user interface was implemented that combines an automatic image feature selector, tracking parameter controls, streaming video viewer, and user generated or autonomous driving commands. Using the test-bed, real-time landmark tracking was demonstrated by autonomously driving the vehicle through the JPL Mars yard. The algorithms tracked rocks as waypoints. This generated coordinates calculating relative motion and visually servoing to science targets. A limitation for the current system is serial computing-each additional landmark is tracked in order-but since each landmark is tracked independently, if transferred to appropriate parallel hardware, adding targets would not significantly diminish system speed.

  17. Development of a Quadrotor Test Bed — Modelling, Parameter Identification, Controller Design and Trajectory Generation

    Directory of Open Access Journals (Sweden)

    Wei Dong

    2015-02-01

    Full Text Available In this paper, a quadrotor test bed is developed. The technical approach for this test bed is firstly proposed by utilizing a commercial quadrotor, a Vicon motion capture system and a ground station. Then, the mathematical model of the quadrotor is formulated considering aerodynamic effects, and the parameter identification approaches for this model are provided accordingly. Based on the developed model and identified parameters, a simulation environment that is consistent with the real system is developed. Subsequently, a flight control strategy and a trajectory generation method, both of which are conceptually and computationally lightweight, are developed and tested in the simulation environment. The developed algorithms are then directly transplanted to the real system, and the experimental results show that their responses in the real-time flights match well with those from the simulations. This indicates that the control algorithms developed for the quadrotor can be preliminarily verified and refined though simulations, and then directly implemented to the real system, which could significantly reduce the experimental risks and costs. Meanwhile, real-time experiments show that the developed flight controller can efficiently stabilize the quadrotor when external disturbances exist, and the trajectory generation approach can provide safe guidance for the quadrotor to fly smoothly through cluttered environments with obstacle rings. All of these features are valuable for real applications, thus demonstrating the feasibility of further development.

  18. DEVELOPMENT OF A SENSOR NETWORK TEST BED FOR ISD MATERIALS AND STRUCUTRAL CONDITION MONITORING

    Energy Technology Data Exchange (ETDEWEB)

    Zeigler, K.; Ferguson, B.; Karapatakis, D.; Herbst, C.; Stripling, C.

    2011-07-06

    The P Reactor at the Savannah River Site is one of the first reactor facilities in the US DOE complex that has been placed in its end state through in situ decommissioning (ISD). The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. To evaluate the feasibility and utility of remote sensors to provide verification of ISD system conditions and performance characteristics, an ISD Sensor Network Test Bed has been designed and deployed at the Savannah River National Laboratory. The test bed addresses the DOE-EM Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of: (1) Groutable thermistors for temperature and moisture monitoring; (2) Strain gauges for crack growth monitoring; (3) Tiltmeters for settlement monitoring; and (4) A communication system for data collection. Preliminary baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment.

  19. Development of a Quadrotor Test Bed — Modelling, Parameter Identification, Controller Design and Trajectory Generation

    Directory of Open Access Journals (Sweden)

    Wei Dong

    2015-02-01

    Full Text Available In this paper, a quadrotor test bed is developed. The technical approach for this test bed is firstly proposed by utilizing a commercial quadrotor, a Vicon motion capture system and a ground station. Then, the mathematical model of the quadrotor is formulated considering aerodynamic effects, and the parameter identification approaches for this model are provided accordingly. Based on the developed model and identified parameters, a simulation environment that is consistent with the real system is developed. Subsequently, a flight control strategy and a trajectory generation method, both of which are conceptually and computationally lightweight, are developed and tested in the simulation environment. The developed algorithms are then directly transplanted to the real system, and the experimental results show that their responses in the real-time flights match well with those from the simulations. This indicates that the control algorithms developed for the quadrotor can be preliminarily verified and refined though simulations, and then directly implemented to the real system, which could significantly reduce the experimental risks and costs. Meanwhile, real-time experiments show that the developed flight controller can efficiently stabilize the quadrotor when external disturbances exist, and the trajectory generation approach can provide safe guidance for the quadrotor to fly smoothly through cluttered environments with obstacle rings. All of these features are valuable for real applications, thus demonstrating the feasibility of further development.

  20. Separate effects tests to determine the thermal dispersion in structured pebble beds in the PBMR HPTU test facility

    Energy Technology Data Exchange (ETDEWEB)

    Toit, C.G. du, E-mail: jat.dutoit@nwu.ac.za; Rousseau, P.G.; Kgame, T.L.

    2014-05-01

    Thermal-fluid simulations are used extensively to predict the maximum fuel temperatures, flows, pressure drops and thermal capacitance of pebble bed gas cooled reactors in support of the reactor safety case. The PBMR company developed the HTTF test facility in cooperation with M-Tech Industrial (Pty) Ltd. and the North-West University in South Africa to conduct comprehensive separate effects tests as well as integrated effects tests to study the different thermal-fluid phenomena. This paper describes the separate effects tests that were conducted to determine the effect of the porous structure on the fluid effective thermal conductivity due to the thermal dispersion. It also presents the methodology applied in the data analysis to derive the resultant values of the effective thermal conductivity and its associated uncertainty.

  1. Fluidized-bed potato waste drying experiments at the Raft River Geothermal Test Site

    Energy Technology Data Exchange (ETDEWEB)

    Cole, L.T.; Schmitt, R.C.

    1980-06-01

    A fluidized-bed dryer was built and operated at the Raft River Geothermal Test Site in south central Idaho to test the feasibility of using low-temperature (145/sup 0/C or lower) geothermal fluids as an energy source for drying operations. The dryer performed successfully on two potato industry waste products that had a solid content of 5 to 13%. The dried product was removed as a sand-like granular material or as fines with a flour-like texture. Test results, observations, and design recommendations are presented. Also presented is an economic evaluation for commercial-scale drying plants using either geothermal low-temperature water or oil as a heat source.

  2. Field Measurements of Perceived Air Quality in the Test-Bed for Innovative Climate Conditioning Technologies

    DEFF Research Database (Denmark)

    Kolarik, Jakub; Toftum, Jørn; Kabrhel, Michal

    , relative humidity and CO2 concentration. Results showed that the mean sensory pollution load in the tested offices was 0.09±0.02 olf/m2 (mean±SEM). This refers to a low-polluting building according to CEN Report CR 1752. The acceptability of the air quality was worst in unoccupied offices ventilated at 20...... m3/h. Application of DCV decreased the CO2 concentration, but did not result in statistically significant improvement of the perceived air quality. It was not possible to quantify the influence on the sensory pollution load of particular technologies tested as part of the Clear-up. However......Field measurements of perceived air quality were conducted in an experimental test bed for innovative building technologies situated at the Czech Technical University in Prague. The technologies included photocatalytically active paint, vacuum porous insulation and wall plaster containing phase...

  3. Testing of the United Stirling 4-95 solar Stirling engine on test bed concentrator

    Science.gov (United States)

    Nelving, H. G.

    1984-01-01

    The objectives with the testing, test set-ups, component designs, and the results of the testing of the solar Stirling engine in a parabolic dish system are presented. The most important tests are characterization of receivers, full day performance of complete system, cavity and aperture window test including influence from windeffects, control system tests, radiator system tests and special temperature measurements with infrared camera. The influence on performance of flux distribution depnding on concentrator alignment, and the optimum receiver operating criteria when balancing flux and temperatures on cooled receiver surface while avoiding flux on uncooled surfaces are also discussed.

  4. Testing of the United Stirling 4-95 solar Stirling engine on test bed concentrator

    Science.gov (United States)

    Nelving, H. G.

    1984-03-01

    The objectives with the testing, test set-ups, component designs, and the results of the testing of the solar Stirling engine in a parabolic dish system are presented. The most important tests are characterization of receivers, full day performance of complete system, cavity and aperture window test including influence from windeffects, control system tests, radiator system tests and special temperature measurements with infrared camera. The influence on performance of flux distribution depnding on concentrator alignment, and the optimum receiver operating criteria when balancing flux and temperatures on cooled receiver surface while avoiding flux on uncooled surfaces are also discussed.

  5. US-VISIT Independent Verification and Validation Project: Test Bed Establishment Report

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, N W; Gansemer, J D

    2011-01-21

    This document describes the computational and data systems available at the Lawrence Livermore National Laboratory for use on the US-VISIT Independent Verification and Validation (IV&V) project. This system - composed of data, software and hardware - is designed to be as close as a representation of the operational ADIS system as is required to verify and validate US-VISIT methodologies. It is not required to reproduce the computational capabilities of the enterprise-class operational system. During FY10, the test bed was simplified from the FY09 version by reducing the number of database host computers from three to one, significantly reducing the maintenance and overhead while simultaneously increasing system throughput. During the current performance period, a database transfer was performed as a set of Data Pump Export files. The previous RMAN backup from 2007 required the availability of an AIX system which is not required when using data pump. Due to efficiencies in the new system and process, loading of the database refresh was able to be accomplished in a much shorter time frame than was previously required. The FY10 Oracle Test Bed now consists of a single Linux platform hosting two Oracle databases including the 2007 copy as well as the October 2010 refresh.

  6. Integration of the SSPM and STAGE with the MPACT Virtual Facility Distributed Test Bed.

    Energy Technology Data Exchange (ETDEWEB)

    Cipiti, Benjamin B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Shoman, Nathan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-08-01

    The Material Protection Accounting and Control Technologies (MPACT) program within DOE NE is working toward a 2020 milestone to demonstrate a Virtual Facility Distributed Test Bed. The goal of the Virtual Test Bed is to link all MPACT modeling tools, technology development, and experimental work to create a Safeguards and Security by Design capability for fuel cycle facilities. The Separation and Safeguards Performance Model (SSPM) forms the core safeguards analysis tool, and the Scenario Toolkit and Generation Environment (STAGE) code forms the core physical security tool. These models are used to design and analyze safeguards and security systems and generate performance metrics. Work over the past year has focused on how these models will integrate with the other capabilities in the MPACT program and specific model changes to enable more streamlined integration in the future. This report describes the model changes and plans for how the models will be used more collaboratively. The Virtual Facility is not designed to integrate all capabilities into one master code, but rather to maintain stand-alone capabilities that communicate results between codes more effectively.

  7. Performance analysis and pilot plant test results for the Komorany fluidized bed retrofit project

    Energy Technology Data Exchange (ETDEWEB)

    Snow, G.C. [POWER International, Inc., Coeur d`Alene, ID (United States)

    1995-12-01

    Detailed heat and mass balance calculations and emission performance projections are presented for an atmospheric fluidized bed boiler bottom retrofit at the 927 MWt (steam output) Komorany power station and district heating plant in the Czech Republic. Each of the ten existing boilers are traveling grate stoker units firing a local, low-rank brown coal. This fuel, considered to be representative of much of the coal deposits in Central Europe, is characterized by an average gross calorific value of 10.5 MJ/kg (4,530 Btu/lb), an average dry basis ash content of 47 %, and a maximum dry basis sulfur content of 1.8 % (3.4 % on a dry, ash free basis). The same fuel supply, together with limestone supplied from the region will be utilized in the retrofit fluidized bed boilers. The primary objectives of this retrofit program are, (1) reduce emissions to a level at or below the new Czech Clean Air Act, and (2) restore plant capacity to the original specification. As a result of the AFBC retrofit and plant upgrade, the particulate matter emissions will be reduced by over 98 percent, SO{sub 2} emissions will be reduced by 88 percent, and NO{sub x} emissions will be reduced by 38 percent compared to the present grate-fired configuration. The decrease in SO{sub 2} emissions resulting from the fluidized bed retrofit was initially predicted based on fuel sulfur content, including the distribution among organic, pyritic, and sulfate forms; the ash alkalinity; and the estimated limestone calcium utilization efficiency. The methodology and the results of this prediction were confirmed and extended by pilot scale combustion trials at a 1.0 MWt (fuel input), variable configuration test facility in France.

  8. Relevance of Item Analysis in Standardizing an Achievement Test in Teaching of Physical Science in B.Ed Syllabus

    Science.gov (United States)

    Marie, S. Maria Josephine Arokia; Edannur, Sreekala

    2015-01-01

    This paper focused on the analysis of test items constructed in the paper of teaching Physical Science for B.Ed. class. It involved the analysis of difficulty level and discrimination power of each test item. Item analysis allows selecting or omitting items from the test, but more importantly item analysis is a tool to help the item writer improve…

  9. Human Exploration System Test-Bed for Integration and Advancement (HESTIA) Support of Future NASA Deep-Space Missions

    Science.gov (United States)

    Marmolejo, Jose; Ewert, Michael

    2016-01-01

    The Engineering Directorate at the NASA - Johnson Space Center is outfitting a 20-Foot diameter hypobaric chamber in Building 7 to support future deep-space Environmental Control & Life Support System (ECLSS) research as part of the Human Exploration System Test-bed for Integration and Advancement (HESTIA) Project. This human-rated chamber is the only NASA facility that has the unique experience, chamber geometry, infrastructure, and support systems capable of conducting this research. The chamber was used to support Gemini, Apollo, and SkyLab Missions. More recently, it was used to conduct 30-, 60-, and 90-day human ECLSS closed-loop testing in the 1990s to support the International Space Station and life support technology development. NASA studies show that both planetary surface and deep-space transit crew habitats will be 3-4 story cylindrical structures driven by human occupancy volumetric needs and launch vehicle constraints. The HESTIA facility offers a 3-story, 20-foot diameter habitat consistent with the studies' recommendations. HESTIA operations follow stringent processes by a certified test team that including human testing. Project management, analysis, design, acquisition, fabrication, assembly and certification of facility build-ups are available to support this research. HESTIA offers close proximity to key stakeholders including astronauts, Human Research Program (who direct space human research for the agency), Mission Operations, Safety & Mission Assurance, and Engineering Directorate. The HESTIA chamber can operate at reduced pressure and elevated oxygen environments including those proposed for deep-space exploration. Data acquisition, power, fluids and other facility resources are available to support a wide range of research. Recently completed HESTIA research consisted of unmanned testing of ECLSS technologies. Eventually, the HESTIA research will include humans for extended durations at reduced pressure and elevated oxygen to demonstrate

  10. Development of a Mobile Robot as a Test Bed for Tele-Presentation

    Directory of Open Access Journals (Sweden)

    Diogenes Armando D. Pascua

    2016-05-01

    Full Text Available In this paper a human-sized tracked wheel robot with a large payload capacity for tele-presentation is presented. The robot is equipped with different sensors for obstacle avoidance and localization. A high definition web camera installed atop a pan and tilt assembly was in place as a remote environment feedback for users. An LCD monitor provides the visual display of the operator in the remote environment using the standard Skype teleconferencing software. Remote control was done via the internet through the free Teamviewer VNC remote desktop software. Moreover, this paper presents the design details, fabrication and evaluation of individual components. Core mobile robot movement and navigational controls were developed and tested. The effectiveness of the mobile robot as a test bed for tele-presentation were evaluated and analyzed by way of its real time response and time delay effects of the network

  11. Development Of A Mobile Robot As A Test Bed For Tele-Presentation

    Directory of Open Access Journals (Sweden)

    Diogenes Armando D. Pascua

    2016-01-01

    Full Text Available In this paper a human-sized tracked wheel robot with a large payload capacity for tele-presentation is presented. The robot is equipped with different sensors for obstacle avoidance and localization. A high definition web camera installed atop a pan and tilt assembly was in place as a remote environment feedback for users. An LCD monitor provides the visual display of the operator in the remote environment using the standard Skype teleconferencing software. Remote control was done via the internet through the free Teamviewer VNC remote desktop software. Moreover, this paper presents the design details, fabrication and evaluation of individual components. Core mobile robot movement and navigational controls were developed and tested. The effectiveness of the mobile robot as a test bed for tele-presentation were evaluated and analyzed by way of its real time response and time delay effects of the network.

  12. Neutron-antineutron transition as a test-bed for dynamical CPT violations

    Science.gov (United States)

    Addazi, Andrea

    2016-05-01

    We show a simple mechanism for a dynamical CPT violation in the neutron sector. In particular, we show a CPT-violating see-saw mechanism, generating a Majorana mass and a CPT-violating mass for the neutron. CPT-violating see-saw involves a sterile partner of the neutron, living in a hidden sector, in which CPT is spontaneously broken. In particular, neutrons (antineutrons) can communicate with the hidden sector through nonperturbative quantum gravity effects called exotic instantons. Exotic instantons dynamically break R-parity, generating one effective vertex between the neutron and its sterile partner. In this way, we show how a small CPT-violating mass term for the neutron is naturally generated. This model can be tested in the next generation of experiments in neutron-antineutron physics. This strongly motivates researches of CPT-violating effects in neutron-antineutron physics as a test-bed for dynamical CPT-violations in SM.

  13. Advanced thermal energy management: A thermal test bed and heat pipe simulation

    Science.gov (United States)

    Barile, Ronald G.

    1986-01-01

    Work initiated on a common-module thermal test simulation was continued, and a second project on heat pipe simulation was begun. The test bed, constructed from surplus Skylab equipment, was modeled and solved for various thermal load and flow conditions. Low thermal load caused the radiator fluid, Coolanol 25, to thicken due to its temperature avoided by using a regenerator-heat-exchanger. Other possible solutions modeled include a radiator heater and shunting heat from the central thermal bus to the radiator. Also, module air temperature can become excessive with high avionics load. A second preoject concerning advanced heat pipe concepts was initiated. A program was written which calculates fluid physical properties, liquid and vapor pressure in the evaporator and condenser, fluid flow rates, and thermal flux. The program is directed to evaluating newer heat pipe wicks and geometries, especially water in an artery surrounded by six vapor channels. Effects of temperature, groove and slot dimensions, and wick properties are reported.

  14. Development and Implementation of a Hardware In-the-Loop Test Bed for Unmanned Aerial Vehicle Control Algorithms

    Science.gov (United States)

    Nyangweso, Emmanuel; Bole, Brian

    2014-01-01

    Successful prediction and management of battery life using prognostic algorithms through ground and flight tests is important for performance evaluation of electrical systems. This paper details the design of test beds suitable for replicating loading profiles that would be encountered in deployed electrical systems. The test bed data will be used to develop and validate prognostic algorithms for predicting battery discharge time and battery failure time. Online battery prognostic algorithms will enable health management strategies. The platform used for algorithm demonstration is the EDGE 540T electric unmanned aerial vehicle (UAV). The fully designed test beds developed and detailed in this paper can be used to conduct battery life tests by controlling current and recording voltage and temperature to develop a model that makes a prediction of end-of-charge and end-of-life of the system based on rapid state of health (SOH) assessment.

  15. CRUCIBLE TESTING OF TANK 48H RADIOACTIVEWASTE SAMPLE USING FLUIDIZED BED STEAMREFORMING TECHNOLOGY FOR ORGANICDESTRUCTION

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C

    2008-07-31

    The purpose of crucible scale testing with actual radioactive Tank 48H material was to duplicate the test results that had been previously performed on simulant Tank 48H material. The earlier crucible scale testing using simulants was successful in demonstrating that bench scale crucible tests produce results that are indicative of actual Fluidized Bed Steam Reforming (FBSR) pilot scale tests. Thus, comparison of the results using radioactive Tank 48H feed to those reported earlier with simulants would then provide proof that the radioactive tank waste behaves in a similar manner to the simulant. Demonstration of similar behavior for the actual radioactive Tank 48H slurry to the simulant is important as a preliminary or preparation step for the more complex bench-scale steam reformer unit that is planned for radioactive application in the Savannah River National Laboratory (SRNL) Shielded Cells Facility (SCF) later in 2008. The goals of this crucible-scale testing were to show 99% destruction of tetraphenylborate and to demonstrate that the final solid product produced is sodium carbonate. Testing protocol was repeated using the specifications of earlier simulant crucible scale testing, that is sealed high purity alumina crucibles containing a pre-carbonated and evaporated Tank 48H material. Sealing of the crucibles was accomplished by using an inorganic 'nepheline' sealant. The sealed crucibles were heat-treated at 650 C under constant argon flow to inert the system. Final product REDOX measurements were performed to establish the REDuction/OXidation (REDOX) state of known amounts of added iron species in the final product. These REDOX measurements confirm the processing conditions (pyrolysis occurring at low oxygen fugacity) of the sealed crucible environment which is the environment actually achieved in the fluidized bed steam reformer process. Solid product dissolution in water was used to measure soluble cations and anions, and to investigate

  16. Creating a Test Validated Structural Dynamic Finite Element Model of the Multi-Utility Technology Test Bed Aircraft

    Science.gov (United States)

    Pak, Chan-Gi; Truong, Samson S.

    2014-01-01

    Small modeling errors in the finite element model will eventually induce errors in the structural flexibility and mass, thus propagating into unpredictable errors in the unsteady aerodynamics and the control law design. One of the primary objectives of Multi Utility Technology Test Bed, X-56A, aircraft is the flight demonstration of active flutter suppression, and therefore in this study, the identification of the primary and secondary modes for the structural model tuning based on the flutter analysis of X-56A. The ground vibration test validated structural dynamic finite element model of the X-56A is created in this study. The structural dynamic finite element model of the X-56A is improved using a model tuning tool. In this study, two different weight configurations of the X-56A have been improved in a single optimization run.

  17. Multi-Column Experimental Test Bed for Xe/Kr Separation

    Energy Technology Data Exchange (ETDEWEB)

    Greenhalgh, Mitchell Randy [Idaho National Lab. (INL), Idaho Falls, ID (United States); Garn, Troy Gerry [Idaho National Lab. (INL), Idaho Falls, ID (United States); Welty, Amy Keil [Idaho National Lab. (INL), Idaho Falls, ID (United States); Lyon, Kevin Lawrence [Idaho National Lab. (INL), Idaho Falls, ID (United States); Watson, Tony Leroy [Idaho National Lab. (INL), Idaho Falls, ID (United States)ry

    2015-08-31

    Previous research studies have shown that INL-developed engineered form sorbents are capable of capturing both Kr and Xe from various composite gas streams. The previous experimental test bed provided single column testing for capacity evaluations over a broad temperature range. To advance research capabilities, the employment of an additional column to study selective capture of target species to provide a defined final gas composition for waste storage was warranted. The second column addition also allows for compositional analyses of the final gas product to provide for final storage determinations. The INL krypton capture system was modified by adding an additional adsorption column in order to create a multi-column test bed. The purpose of this modification was to investigate the separation of xenon from krypton supplied as a mixed gas feed. The extra column was placed in a Stirling Ultra-low Temperature Cooler, capable of controlling temperatures between 190 and 253K. Additional piping and valves were incorporated into the system to allow for a variety of flow path configurations. The new column was filled with the AgZ-PAN sorbent which was utilized as the capture medium for xenon while allowing the krypton to pass through. The xenon-free gas stream was then routed to the cryostat filled with the HZ-PAN sorbent to capture the krypton at 191K. Selectivities of xenon over krypton were determined using the new column to verify the system performance and to establish the operating conditions required for multi-column testing. Results of these evaluations verified that the system was operating as designed and also demonstrated that AgZ-PAN exhibits excellent selectivity for xenon over krypton in air at or near room temperature. Two separation tests were performed utilizing a feed gas consisting of 1000 ppmv xenon and 150 ppmv krypton with the balance being made up of air. The AgZ-PAN temperature was held at 295 or 253K while the HZ-PAN was held at 191K for both

  18. JV Task 108 - Circulating Fluidized-Bed Combustion and Combustion Testing of Turkish Tufanbeyli Coal

    Energy Technology Data Exchange (ETDEWEB)

    Douglas Hajicek; Jay Gunderson; Ann Henderson; Stephen Sollom; Joshua Stanislowski

    2007-08-15

    Two combustion tests were performed at the Energy & Environmental Research Center (EERC) using Tufanbeyli coal from Turkey. The tests were performed in a circulating fluidized-bed combustor (CFBC) and a pulverized coal-fired furnace, referred to as the combustion test facility (CTF). One of the goals of the project was to determine the type of furnace best suited to this coal. The coal is high in moisture, ash, and sulfur and has a low heating value. Both the moisture and the sulfur proved problematic for the CTF tests. The fuel had to be dried to less than 37% moisture before it could be pulverized and further dried to about 25% moisture to allow more uniform feeding into the combustor. During some tests, water was injected into the furnace to simulate the level of flue gas moisture had the fuel been fed without drying. A spray dryer was used downstream of the baghouse to remove sufficient sulfur to meet the EERC emission standards permitted by the North Dakota Department of Health. In addition to a test matrix varying excess air, burner swirl, and load, two longer-term tests were performed to evaluate the fouling potential of the coal at two different temperatures. At the lower temperature (1051 C), very little ash was deposited on the probes, but deposition did occur on the walls upstream of the probe bank, forcing an early end to the test after 2 hours and 40 minutes of testing. At the higher temperature (1116 C), ash deposition on the probes was significant, resulting in termination of the test after only 40 minutes. The same coal was burned in the CFBC, but because the CFBC uses a larger size of material, it was able to feed this coal at a higher moisture content (average of 40.1%) compared to the CTF (ranging from 24.2% to 26.9%). Sulfur control was achieved with the addition of limestone to the bed, although the high calcium-to-sulfur rate required to reduce SO{sub 2} emissions resulted in heat loss (through limestone calcination) and additional ash

  19. RESOURCE ASSESSMENT & PRODUCTION TESTING FOR COAL BED METHANE IN THE ILLINOIS BASIN

    Energy Technology Data Exchange (ETDEWEB)

    Cortland Eble; James Drahovzal; David Morse; Ilham Demir; John Rupp; Maria Mastalerz; Wilfrido Solano

    2004-06-01

    The geological surveys of Illinois, Indiana and Kentucky have completed the initial geologic assessment of their respective parts of the Illinois Basin. Cumulative thickness maps have been generated and target areas for drilling have been selected. The first well in the Illinois area of the Illinois Basin coal bed methane project was drilled in White County, Illinois in October 2003. This well was cored in the major coal interval from the Danville to the Davis Coals and provided a broad spectrum of samples for further analyses. Sixteen coal samples and three black shale samples were taken from these cores for canister desorption tests and were the subject of analyses that were completed over the following months, including desorbed gas volume, gas chemical and isotope composition, coal proximate, calorific content and sulfur analyses. Drilling programs in Indiana and Kentucky are expected to begin shortly.

  20. High-Resolution Adaptive Optics Test-Bed for Vision Science

    Energy Technology Data Exchange (ETDEWEB)

    Wilks, S C; Thomspon, C A; Olivier, S S; Bauman, B J; Barnes, T; Werner, J S

    2001-09-27

    We discuss the design and implementation of a low-cost, high-resolution adaptive optics test-bed for vision research. It is well known that high-order aberrations in the human eye reduce optical resolution and limit visual acuity. However, the effects of aberration-free eyesight on vision are only now beginning to be studied using adaptive optics to sense and correct the aberrations in the eye. We are developing a high-resolution adaptive optics system for this purpose using a Hamamatsu Parallel Aligned Nematic Liquid Crystal Spatial Light Modulator. Phase-wrapping is used to extend the effective stroke of the device, and the wavefront sensing and wavefront correction are done at different wavelengths. Issues associated with these techniques will be discussed.

  1. A test bed for the future access control system the AD Project

    CERN Document Server

    Scibile, L

    1999-01-01

    This paper describes the design, management and development of the new access control system for the Antiproton Deceleration experimental area, called the AD Project. As this project includes all the elements for the industrial evolution of the present access control system it is an ideal test bed for future access systems. The adoption of new technologies and techniques are described, and the benefits and the shortfalls are highlighted. The open redundant architecture solution, based on a PROFIBUS network and standard industrial components (HP-UNIX, Siemens S7 PLC, Siemens Industrial PC, door locks), guarantees reliability, safety and optimal integration. The project team took advantage of the Goal Directed Project Management technique and managed to define a clear and effective strategy.

  2. Organic molecule fluorescence as an experimental test-bed for quantum jumps in thermodynamics.

    Science.gov (United States)

    Browne, Cormac; Farrow, Tristan; Dahlsten, Oscar C O; Taylor, Robert A; Vlatko, Vedral

    2017-08-01

    We demonstrate with an experiment how molecules are a natural test bed for probing fundamental quantum thermodynamics. Single-molecule spectroscopy has undergone transformative change in the past decade with the advent of techniques permitting individual molecules to be distinguished and probed. We demonstrate that the quantum Jarzynski equality for heat is satisfied in this set-up by considering the time-resolved emission spectrum of organic molecules as arising from quantum jumps between states. This relates the heat dissipated into the environment to the free energy difference between the initial and final state. We demonstrate also how utilizing the quantum Jarzynski equality allows for the detection of energy shifts within a molecule, beyond the relative shift.

  3. Pregnancy does not affect HIV incidence test results obtained using the BED capture enzyme immunoassay or an antibody avidity assay.

    Directory of Open Access Journals (Sweden)

    Oliver Laeyendecker

    Full Text Available BACKGROUND: Accurate incidence estimates are needed for surveillance of the HIV epidemic. HIV surveillance occurs at maternal-child health clinics, but it is not known if pregnancy affects HIV incidence testing. METHODS: We used the BED capture immunoassay (BED and an antibody avidity assay to test longitudinal samples from 51 HIV-infected Ugandan women infected with subtype A, C, D and intersubtype recombinant HIV who were enrolled in the HIVNET 012 trial (37 baseline samples collected near the time of delivery and 135 follow-up samples collected 3, 4 or 5 years later. Nineteen of 51 women were also pregnant at the time of one or more of the follow-up visits. The BED assay was performed according to the manufacturer's instructions. The avidity assay was performed using a Genetic Systems HIV-1/HIV-2 + O EIA using 0.1M diethylamine as the chaotropic agent. RESULTS: During the HIVNET 012 follow-up study, there was no difference in normalized optical density values (OD-n obtained with the BED assay or in the avidity test results (% when women were pregnant (n = 20 results compared to those obtained when women were not pregnant (n = 115; for BED: p = 0.9, generalized estimating equations model; for avidity: p = 0.7, Wilcoxon rank sum. In addition, BED and avidity results were almost exactly the same in longitudinal samples from the 18 women who were pregnant at only one study visit during the follow-up study (p = 0.6, paired t-test. CONCLUSIONS: These results from 51 Ugandan women suggest that any changes in the antibody response to HIV infection that occur during pregnancy are not sufficient to alter results obtained with the BED and avidity assays. Confirmation with larger studies and with other HIV subtypes is needed.

  4. Space-Based Reconfigurable Software Defined Radio Test Bed Aboard International Space Station

    Science.gov (United States)

    Reinhart, Richard C.; Lux, James P.

    2014-01-01

    The National Aeronautical and Space Administration (NASA) recently launched a new software defined radio research test bed to the International Space Station. The test bed, sponsored by the Space Communications and Navigation (SCaN) Office within NASA is referred to as the SCaN Testbed. The SCaN Testbed is a highly capable communications system, composed of three software defined radios, integrated into a flight system, and mounted to the truss of the International Space Station. Software defined radios offer the future promise of in-flight reconfigurability, autonomy, and eventually cognitive operation. The adoption of software defined radios offers space missions a new way to develop and operate space transceivers for communications and navigation. Reconfigurable or software defined radios with communications and navigation functions implemented in software or VHDL (Very High Speed Hardware Description Language) provide the capability to change the functionality of the radio during development or after launch. The ability to change the operating characteristics of a radio through software once deployed to space offers the flexibility to adapt to new science opportunities, recover from anomalies within the science payload or communication system, and potentially reduce development cost and risk by adapting generic space platforms to meet specific mission requirements. The software defined radios on the SCaN Testbed are each compliant to NASA's Space Telecommunications Radio System (STRS) Architecture. The STRS Architecture is an open, non-proprietary architecture that defines interfaces for the connections between radio components. It provides an operating environment to abstract the communication waveform application from the underlying platform specific hardware such as digital-to-analog converters, analog-to-digital converters, oscillators, RF attenuators, automatic gain control circuits, FPGAs, general-purpose processors, etc. and the interconnections among

  5. Plans of a test bed for ionospheric modelling based on Fennoscandian ground-based instrumentation

    Science.gov (United States)

    Kauristie, Kirsti; Kero, Antti; Verronen, Pekka T.; Aikio, Anita; Vierinen, Juha; Lehtinen, Markku; Turunen, Esa; Pulkkinen, Tuija; Virtanen, Ilkka; Norberg, Johannes; Vanhamäki, Heikki; Kallio, Esa; Kestilä, Antti; Partamies, Noora; Syrjäsuo, Mikko

    2016-07-01

    One of the recommendations for teaming among research groups in the COSPAR/ILWS roadmap is about building test beds in which coordinated observing supports model development. In the presentation we will describe a test bed initiative supporting research on ionosphere-thermosphere-magnetosphere interactions. The EISCAT incoherent scatter radars with their future extension, EISCAT3D, form the backbone of the proposed system. The EISCAT radars are surrounded by versatile and dense arrays of ground-based instrumentation: magnetometers and auroral cameras (the MIRACLE and IMAGE networks), ionospheric tomography receivers (the TomoScand network) and other novel technology for upper atmospheric probing with radio waves (e.g. the KAIRA facility, riometers and the ionosonde maintained by the Sodankylä Geophysical Observatory). As a new opening, close coordination with the Finnish national cubesat program is planned. We will investigate opportunities to establish a cost efficient nanosatellite program which would support the ground-based observations in a systematic and persistent manner. First experiences will be gathered with the Aalto-1 and Aalto-2 satellites, latter of which will be the Finnish contribution to the international QB50 mission. We envisage close collaboration also in the development of data analysis tools with the goal to integrate routines and models from different research groups to one system, where the different elements support each other. In the longer run we are aiming for a modelling framework with observational guidance which gives a holistic description on ionosphere-thermosphere processes and this way enables reliable forecasts on upper atmospheric space weather activity.

  6. Threat and efficacy uncertainty in news coverage about bed bugs as unique predictors of information seeking and avoidance: an extension of the EPPM.

    Science.gov (United States)

    Goodall, Catherine E; Reed, Phillip

    2013-01-01

    An experiment was conducted from the perspective of the Extended Parallel Process Model (EPPM) investigating readers' responses to print news stories about the issue of bed bugs. Stories containing reference to (a) the threat of bed bugs and (b) efficacy of the solution were manipulated to vary the level of certainty with which the variables were discussed. Results suggest that stories referencing uncertainty regarding presence of the bed-bug threat may be more likely to motivate intention to seek information than stories referencing certainty of the threat. Results also suggest that stories referencing uncertainty regarding feasibility/effectiveness of proposed solutions may be more likely to motivate intention to avoid information than stories referencing certainty of proposed solutions. Given that information avoidance is one of various types of maladaptive responses to fear appeal messages (according to EPPM), results suggest that the presence of uncertainty when discussing solutions to threats in news stories might result in problematic avoidance responses that discourage people from taking protective action.

  7. Fluidized bed steam reformed mineral waste form performance testing to support Hanford Supplemental Low Activity Waste Immobilization Technology Selection

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Pierce, E. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Herman, C. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brown, C. F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, N. P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Neeway, J. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Valenta, M. M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gill, G. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Swanberg, D. J. [Washington River Protection Solutions (WRPS), Richland, WA (United States); Robbins, R. A. [Washington River Protection Solutions (WRPS), Richland, WA (United States); Thompson, L. E. [Washington River Protection Solutions (WRPS), Richland, WA (United States)

    2015-10-01

    This report describes the benchscale testing with simulant and radioactive Hanford Tank Blends, mineral product characterization and testing, and monolith testing and characterization. These projects were funded by DOE EM-31 Technology Development & Deployment (TDD) Program Technical Task Plan WP-5.2.1-2010-001 and are entitled “Fluidized Bed Steam Reformer Low-Level Waste Form Qualification”, Inter-Entity Work Order (IEWO) M0SRV00054 with Washington River Protection Solutions (WRPS) entitled “Fluidized Bed Steam Reforming Treatability Studies Using Savannah River Site (SRS) Low Activity Waste and Hanford Low Activity Waste Tank Samples”, and IEWO M0SRV00080, “Fluidized Bed Steam Reforming Waste Form Qualification Testing Using SRS Low Activity Waste and Hanford Low Activity Waste Tank Samples”. This was a multi-organizational program that included Savannah River National Laboratory (SRNL), THOR® Treatment Technologies (TTT), Pacific Northwest National Laboratory (PNNL), Oak Ridge National Laboratory (ORNL), Office of River Protection (ORP), and Washington River Protection Solutions (WRPS). The SRNL testing of the non-radioactive pilot-scale Fluidized Bed Steam Reformer (FBSR) products made by TTT, subsequent SRNL monolith formulation and testing and studies of these products, and SRNL Waste Treatment Plant Secondary Waste (WTP-SW) radioactive campaign were funded by DOE Advanced Remediation Technologies (ART) Phase 2 Project in connection with a Work-For-Others (WFO) between SRNL and TTT.

  8. In Situ Decommissioning Sensor Network, Meso-Scale Test Bed - Phase 3 Fluid Injection Test Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Serrato, M. G.

    2013-09-27

    The DOE Office of Environmental management (DOE EM) faces the challenge of decommissioning thousands of excess nuclear facilities, many of which are highly contaminated. A number of these excess facilities are massive and robust concrete structures that are suitable for isolating the contained contamination for hundreds of years, and a permanent decommissioning end state option for these facilities is in situ decommissioning (ISD). The ISD option is feasible for a limited, but meaningfull number of DOE contaminated facilities for which there is substantial incremental environmental, safety, and cost benefits versus alternate actions to demolish and excavate the entire facility and transport the rubble to a radioactive waste landfill. A general description of an ISD project encompasses an entombed facility; in some cases limited to the blow-grade portion of a facility. However, monitoring of the ISD structures is needed to demonstrate that the building retains its structural integrity and the contaminants remain entombed within the grout stabilization matrix. The DOE EM Office of Deactivation and Decommissioning and Facility Engineering (EM-13) Program Goal is to develop a monitoring system to demonstrate long-term performance of closed nuclear facilities using the ISD approach. The Savannah River National Laboratory (SRNL) has designed and implemented the In Situ Decommissioning Sensor Network, Meso-Scale Test Bed (ISDSN-MSTB) to address the feasibility of deploying a long-term monitoring system into an ISD closed nuclear facility. The ISDSN-MSTB goal is to demonstrate the feasibility of installing and operating a remote sensor network to assess cementitious material durability, moisture-fluid flow through the cementitious material, and resulting transport potential for contaminate mobility in a decommissioned closed nuclear facility. The original ISDSN-MSTB installation and remote sensor network operation was demonstrated in FY 2011-12 at the ISDSN-MSTB test cube

  9. The PRIMA Test Facility: SPIDER and MITICA test-beds for ITER neutral beam injectors

    Science.gov (United States)

    Toigo, V.; Piovan, R.; Dal Bello, S.; Gaio, E.; Luchetta, A.; Pasqualotto, R.; Zaccaria, P.; Bigi, M.; Chitarin, G.; Marcuzzi, D.; Pomaro, N.; Serianni, G.; Agostinetti, P.; Agostini, M.; Antoni, V.; Aprile, D.; Baltador, C.; Barbisan, M.; Battistella, M.; Boldrin, M.; Brombin, M.; Dalla Palma, M.; De Lorenzi, A.; Delogu, R.; De Muri, M.; Fellin, F.; Ferro, A.; Fiorentin, A.; Gambetta, G.; Gnesotto, F.; Grando, L.; Jain, P.; Maistrello, A.; Manduchi, G.; Marconato, N.; Moresco, M.; Ocello, E.; Pavei, M.; Peruzzo, S.; Pilan, N.; Pimazzoni, A.; Recchia, M.; Rizzolo, A.; Rostagni, G.; Sartori, E.; Siragusa, M.; Sonato, P.; Sottocornola, A.; Spada, E.; Spagnolo, S.; Spolaore, M.; Taliercio, C.; Valente, M.; Veltri, P.; Zamengo, A.; Zaniol, B.; Zanotto, L.; Zaupa, M.; Boilson, D.; Graceffa, J.; Svensson, L.; Schunke, B.; Decamps, H.; Urbani, M.; Kushwah, M.; Chareyre, J.; Singh, M.; Bonicelli, T.; Agarici, G.; Garbuglia, A.; Masiello, A.; Paolucci, F.; Simon, M.; Bailly-Maitre, L.; Bragulat, E.; Gomez, G.; Gutierrez, D.; Mico, G.; Moreno, J.-F.; Pilard, V.; Kashiwagi, M.; Hanada, M.; Tobari, H.; Watanabe, K.; Maejima, T.; Kojima, A.; Umeda, N.; Yamanaka, H.; Chakraborty, A.; Baruah, U.; Rotti, C.; Patel, H.; Nagaraju, M. V.; Singh, N. P.; Patel, A.; Dhola, H.; Raval, B.; Fantz, U.; Heinemann, B.; Kraus, W.; Hanke, S.; Hauer, V.; Ochoa, S.; Blatchford, P.; Chuilon, B.; Xue, Y.; De Esch, H. P. L.; Hemsworth, R.; Croci, G.; Gorini, G.; Rebai, M.; Muraro, A.; Tardocchi, M.; Cavenago, M.; D'Arienzo, M.; Sandri, S.; Tonti, A.

    2017-08-01

    The ITER Neutral Beam Test Facility (NBTF), called PRIMA (Padova Research on ITER Megavolt Accelerator), is hosted in Padova, Italy and includes two experiments: MITICA, the full-scale prototype of the ITER heating neutral beam injector, and SPIDER, the full-size radio frequency negative-ions source. The NBTF realization and the exploitation of SPIDER and MITICA have been recognized as necessary to make the future operation of the ITER heating neutral beam injectors efficient and reliable, fundamental to the achievement of thermonuclear-relevant plasma parameters in ITER. This paper reports on design and R&D carried out to construct PRIMA, SPIDER and MITICA, and highlights the huge progress made in just a few years, from the signature of the agreement for the NBTF realization in 2011, up to now—when the buildings and relevant infrastructures have been completed, SPIDER is entering the integrated commissioning phase and the procurements of several MITICA components are at a well advanced stage.

  10. DEVELOPMENT OF AN EXPERIMENTAL TEST BED DESIGNATED FOR MODEL STUDIES OF AERODYNAMICS OF PREMISES USING METHOD OF DIGITAL FLOW VISUALIZATION

    Directory of Open Access Journals (Sweden)

    Varapaev Vladimir Nikolaevich

    2012-12-01

    Full Text Available In the article, the authors present their findings generated at the laboratory of aerodynamic and aero-acoustic testing of structural units of MGSU. The authors provide information about the principle of operation and a brief description of the experimental test bed designated for the physical research of patterns of air flows arising inside building premises of various geometric shapes. The authors also demonstrate the basic parameters of the test bed, the principle of operation of its recording devices and some of its characteristics. The test bed is designated for the identification of characteristics of three-dimensional flows of models under research and for the verification of results of numerical studies. The measurement bed has advanced measurement and registration units. The management principle is based on the method of digital flow visualization, PIV method and Doppler flow meter implemented in the LDA anemometer. The test stand generates two or three component vector fields of turbulent gas flow velocities. It may be applicable to the study of liquids in case of research of hydraulics-related problems. Some results of the flow study are provided in the article, as well.

  11. An Envision of Low Cost Mobile Adhoc Network Test Bed in a Laboratory Environment Emulating an Actual MANET

    CERN Document Server

    Mhala, Nitiket N; 10.5121/ijcnc.2010.2305

    2010-01-01

    Orchestrating a live field trial of wireless mobile networking involves significant cost and logistical issues relating to mobile platforms, support personnel, network and experiment automation and support equipment. The significant cost and logistics required to execute such a field trial can also be limiting in terms of achieving meaningful test results that exercise a practical number of mobile nodes over a significant set of test conditions within a given time. There is no argument that field trials are an important component of dynamic network testing. A field test of prototype will show whether simulations were on right track or not, but that's a big leap to take; going from the simulator directly to the real thing. In conceiving our work, we envisioned a mobile network emulation system that is low cost, flexible and controllable. This paper describes our wireless MANET test bed under development which emulates an actual MANET. Here, we focuses that, this test bed allows the users to automatically gener...

  12. Comparison of System Identification Techniques for the Hydraulic Manipulator Test Bed (HMTB)

    Science.gov (United States)

    Morris, A. Terry

    1996-01-01

    In this thesis linear, dynamic, multivariable state-space models for three joints of the ground-based Hydraulic Manipulator Test Bed (HMTB) are identified. HMTB, housed at the NASA Langley Research Center, is a ground-based version of the Dexterous Orbital Servicing System (DOSS), a representative space station manipulator. The dynamic models of the HMTB manipulator will first be estimated by applying nonparametric identification methods to determine each joint's response characteristics using various input excitations. These excitations include sum of sinusoids, pseudorandom binary sequences (PRBS), bipolar ramping pulses, and chirp input signals. Next, two different parametric system identification techniques will be applied to identify the best dynamical description of the joints. The manipulator is localized about a representative space station orbital replacement unit (ORU) task allowing the use of linear system identification methods. Comparisons, observations, and results of both parametric system identification techniques are discussed. The thesis concludes by proposing a model reference control system to aid in astronaut ground tests. This approach would allow the identified models to mimic on-orbit dynamic characteristics of the actual flight manipulator thus providing astronauts with realistic on-orbit responses to perform space station tasks in a ground-based environment.

  13. Hydroponics Database and Handbook for the Advanced Life Support Test Bed

    Science.gov (United States)

    Nash, Allen J.

    1999-01-01

    During the summer 1998, I did student assistance to Dr. Daniel J. Barta, chief plant growth expert at Johnson Space Center - NASA. We established the preliminary stages of a hydroponic crop growth database for the Advanced Life Support Systems Integration Test Bed, otherwise referred to as BIO-Plex (Biological Planetary Life Support Systems Test Complex). The database summarizes information from published technical papers by plant growth experts, and it includes bibliographical, environmental and harvest information based on plant growth under varying environmental conditions. I collected 84 lettuce entries, 14 soybean, 49 sweet potato, 16 wheat, 237 white potato, and 26 mix crop entries. The list will grow with the publication of new research. This database will be integrated with a search and systems analysis computer program that will cross-reference multiple parameters to determine optimum edible yield under varying parameters. Also, we have made preliminary effort to put together a crop handbook for BIO-Plex plant growth management. It will be a collection of information obtained from experts who provided recommendations on a particular crop's growing conditions. It includes bibliographic, environmental, nutrient solution, potential yield, harvest nutritional, and propagation procedure information. This handbook will stand as the baseline growth conditions for the first set of experiments in the BIO-Plex facility.

  14. Design of a Loose Part Monitoring System Test-bed using CompactRIO

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Min-seok; Lee, Kwang-Dae; Lee, Eui-Jong [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    A loose part monitoring system (LPMS) is included in the NSSS integrity monitoring system (NIMS), which serves to detect loose parts in reactor coolant systems (RCS). LPMSs at Nuclear Power Plants (NPPs) in Korea follow the ASME OM standard and acquire data from 18 sensors simultaneously. Data acquisition requires a sampling rate of more than 50KHz along with a 12bit A/D converter. Existing LPMS equipment is composed of several different platforms, such as a digital signal processor (DSP), a field-programmable gate array (FPGA), a micro control unit (MCU), and electric circuit cards. These systems have vulnerabilities, such as discontinuance due to aging and incompatibility issues between different pieces of equipment. This paper suggests CompactRIO as a new platform. We devised a Test-bed using CompactRIO and demonstrate that the proposed method meets the criteria required by the standard. The LPMS provides an alert when an impact event occurs and provides information with which to analyze the location, energy, and mass of the loose parts. LPMSs in NPPs in Korea operate on a variety of platforms. Thus, these systems are vulnerable to discontinuances due to aging and incompatibilities arising from the use of different type of equipment. In order to solve these problems, this paper suggests CompactRIO as a new platform. It is a rugged, reconfigurable, high-performance industrial embedded system. The results of performance tests meet the criteria set by the current standard.

  15. Demonstration of the zero-crossing phasemeter with a LISA test-bed interferometer

    Science.gov (United States)

    Pollack, S. E.; Stebbins, R. T.

    2006-06-01

    The laser interferometer space antenna (LISA) is being designed to detect and study in detail gravitational waves from sources throughout the Universe such as massive black hole binaries. The conceptual formulation of the LISA space-borne gravitational wave detector is now well developed. The interferometric measurements between the sciencecraft remain one of the most important technological and scientific design areas for the mission. Our work has concentrated on developing the interferometric technologies to create a LISA-like optical signal and to measure the phase of that signal using commercially available instruments. One of the most important goals of this research is to demonstrate the LISA phase timing and phase reconstruction for a LISA-like fringe signal, in the case of a high fringe rate and a low signal level. We present current results of a test-bed interferometer designed to produce an optical LISA-like fringe signal previously discussed in Jennrich O, Stebbins R T, Bender P L and Pollack S (2001 Class. Quantum Grav. 18 4159 64) and Pollack S E, Jennrich O, Stebbins R T and Bender P (2003 Class. Quantum Grav. 20 S291 00).

  16. Demonstration of the zero-crossing phasemeter with a LISA test-bed interferometer

    Energy Technology Data Exchange (ETDEWEB)

    Pollack, S E [JILA, University of Colorado, Boulder, CO 80309-0440 (United States); Stebbins, R T [NASA/GSFC Code 661, Greenbelt, MD 20771 (United States)

    2006-06-21

    The laser interferometer space antenna (LISA) is being designed to detect and study in detail gravitational waves from sources throughout the Universe such as massive black hole binaries. The conceptual formulation of the LISA space-borne gravitational wave detector is now well developed. The interferometric measurements between the sciencecraft remain one of the most important technological and scientific design areas for the mission. Our work has concentrated on developing the interferometric technologies to create a LISA-like optical signal and to measure the phase of that signal using commercially available instruments. One of the most important goals of this research is to demonstrate the LISA phase timing and phase reconstruction for a LISA-like fringe signal, in the case of a high fringe rate and a low signal level. We present current results of a test-bed interferometer designed to produce an optical LISA-like fringe signal previously discussed in Jennrich O, Stebbins R T, Bender P L and Pollack S (2001 Class. Quantum Grav. 18 4159-64) and Pollack S E, Jennrich O, Stebbins R T and Bender P (2003 Class. Quantum Grav. 20 S291-00)

  17. A Modular Building Controls Virtual Test Bed for the Integrations of Heterogeneous Systems

    Energy Technology Data Exchange (ETDEWEB)

    Wetter, Michael; Wetter, Michael; Haves, Philip

    2008-06-30

    This paper describes the Building Controls Virtual Test Bed (BCVTB) that is currently under development at Lawrence Berkeley National Laboratory. An earlier prototype linked EnergyPlus with controls hardware through embedded SPARK models and demonstrated its value in more cost-effective envelope design and improved controls sequences for the San Francisco Federal Building. The BCVTB presented here is a more modular design based on a middleware that we built using Ptolemy II, a modular software environment for design and analysis of heterogeneous systems. Ptolemy II provides a graphical model building environment, synchronizes the exchanged data and visualizes the system evolution during run-time. Our additions to Ptolemy II allow users to couple to Ptolemy II a prototype version of EnergyPlus,MATLAB/Simulink or other simulation programs for data exchange during run-time. In future work we will also implement a BACnet interface that allows coupling BACnet compliant building automation systems to Ptolemy II. We will present the architecture of the BCVTB and explain how users can add their own simulation programs to the BCVTB. We will then present an example application in which the building envelope and the HVAC system was simulated in EnergyPlus, the supervisory control logic was simulated in MATLAB/Simulink and Ptolemy II was used to exchange data during run-time and to provide realtime visualization as the simulation progresses.

  18. Co-Simulation of Building Energy and Control Systems with the Building Controls Virtual Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Wetter, Michael

    2010-08-22

    This article describes the implementation of the Building Controls Virtual Test Bed (BCVTB). The BCVTB is a software environment that allows connecting different simulation programs to exchange data during the time integration, and that allows conducting hardware in the loop simulation. The software architecture is a modular design based on Ptolemy II, a software environment for design and analysis of heterogeneous systems. Ptolemy II provides a graphical model building environment, synchronizes the exchanged data and visualizes the system evolution during run-time. The BCVTB provides additions to Ptolemy II that allow the run-time coupling of different simulation programs for data exchange, including EnergyPlus, MATLAB, Simulink and the Modelica modelling and simulation environment Dymola. The additions also allow executing system commands, such as a script that executes a Radiance simulation. In this article, the software architecture is presented and the mathematical model used to implement the co-simulation is discussed. The simulation program interface that the BCVTB provides is explained. The article concludes by presenting applications in which different state of the art simulation programs are linked for run-time data exchange. This link allows the use of the simulation program that is best suited for the particular problem to model building heat transfer, HVAC system dynamics and control algorithms, and to compute a solution to the coupled problem using co-simulation.

  19. Testing of zinc titanate desulfurization sorbents for moving-bed applications

    Energy Technology Data Exchange (ETDEWEB)

    Ayala, R.E.; Gal, E. [General Electric Co., Schenectady, NY (United States). Corporate Research and Development Dept.; Gupta, R.P. [Research Triangle Inst., Research Triangle Park, NC (United States)

    1993-09-01

    Sorbents developed for moving-bed systems must comply with a minimum of chemical and mechanical durability performance characteristics in order to be considered acceptable for long-term operation. Among the desired properties, a sorbent must have: (1) High chemical reactivity, as measured by the rate of sulfur absorption and the total sulfur loading on the sorbent. (2) High mechanical strength, as measured by the pellet crush strength and the attrition resistance; (3) Suitable pellet morphology, as given by pellet size and shape to promote good bulk flow ability and seasonable porosity to increase reactivity. Formulation 2A1.7M (UCI designation L-3787M) was selected by DOE as the baseline formulation for performance evaluation of Option 3 sorbents. This baseline formulation is a rounded zinc titanate sorbent containing a 2:1 Zn:Ti molar ratio, 1.7% molybdenum (equivalent to 2.5% MoO{sub 3}), and 3% bentonite binder that had been previously tested under the Option 2 program. Zinc titanate sorbents were prepared by UCI as rounded spherical or ellipsoidal pellets. The fabrication procedure is targeted at achieving a balance of mechanical strength (crush strength and attrition resistance) and chemical reactivity by controlling the pellet internal porosity.

  20. Distributed Power Control Network and Green Building Test-Bed for Demand Response in Smart Grid

    Science.gov (United States)

    Sakaguchi, Kei; Nguyen, Van Ky; Tao, Yu; Tran, Gia Khanh; Araki, Kiyomichi

    It is known that demand and supply power balancing is an essential method to operate power delivery system and prevent blackouts caused by power shortage. In this paper, we focus on the implementation of demand response strategy to save power during peak hours by using Smart Grid. It is obviously impractical with centralized power control network to realize the real-time control performance, where a single central controller measures the huge metering data and sends control command back to all customers. For that purpose, we propose a new architecture of hierarchical distributed power control network which is scalable regardless of the network size. The sub-controllers are introduced to partition the large system into smaller distributed clusters where low-latency local feedback power control loops are conducted to guarantee control stability. Furthermore, sub-controllers are stacked up in an hierarchical manner such that data are fed back layer-by-layer in the inbound while in the outbound control responses are decentralized in each local sub-controller for realizing the global objectives. Numerical simulations in a realistic scenario of up to 5000 consumers show the effectiveness of the proposed scheme to achieve a desired 10% peak power saving by using off-the-shelf wireless devices with IEEE802.15.4g standard. In addition, a small scale power control system for green building test-bed is implemented to demonstrate the potential use of the proposed scheme for power saving in real life.

  1. Networked seduction: a test-bed for the study of strategic communication on the Internet.

    Science.gov (United States)

    Mantovani, F

    2001-02-01

    One of the emerging features of the Internet is its relational and communicative nature: the initial centrality of the information exchange is moving to the building of online relationships, from friendship to romantic and even sexual relationships. The main goal of this paper is to define a theoretical model for the study of seductive processes on the Internet. In particular, taking up the perspective of the user, a shift of focus is proposed: from the description of the development of interpersonal attraction to the investigation of seduction, considered as a strategic communication process. According to the presented model, the key effort of the subjects involved in a computer-mediated seductive interaction is the negotiation of the meaning of the situation they are involved in. This process usually requires two tasks: the analysis of the characteristics of the communicative environment in which the play of interpersonal attraction develops, and the exploitation of the affordances offered by the communicative environment according to specific strategic goals. The main features of the model are both the focus on the communicative tools employed by the users to reach their relational goals, and the ergonomic characteristics of the networked environment. This approach can be used as a test-bed for the definition of specific hypotheses concerning the development of seductive interaction online.

  2. First results of the Test-Bed Telescopes (TBT) project: Cebreros telescope commissioning

    CERN Document Server

    Ocaña, Francisco; Racero, Elena; Montero, Ángel; Doubek, Jirí; Ruiz, Vicente

    2016-01-01

    The TBT project is being developed under ESA's General Studies and Technology Programme (GSTP), and shall implement a test-bed for the validation of an autonomous optical observing system in a realistic scenario within the Space Situational Awareness (SSA) programme of the European Space Agency (ESA). The goal of the project is to provide two fully robotic telescopes, which will serve as prototypes for development of a future network. The system consists of two telescopes, one in Spain and the second one in the Southern Hemisphere. The telescope is a fast astrograph with a large Field of View of 2.5 x 2.5 square-degrees and a plate scale of 2.2 arcsec/pixel. The tube is mounted on a fast direct-drive mount moving with speed up to 20 degrees per second. The focal plane hosts a 2-port 4K x 4K back-illuminated CCD with readout speeds up to 1MHz per port. Detection software and hardware are optimised for the detection of NEOs and objects in high Earth orbits (objects moving from 0.1-40 arcsec/second). Every night...

  3. The NASA Short-term Prediction and Research Transition (SPoRT) Center: A Research to Operations Test Bed

    Science.gov (United States)

    Jedlovec, Gary J.

    2005-01-01

    to the Florida coastal WFOs. A SPoRT Test bed, together with input from other interagency and university partners, will provide a means and a process to effectively transition ESE observations and technology to NWS operations and decision makers at both the globdnational and regional scales. The transition of emerging experimental products into operations through the SPoRT infrastructure will allow NASA to foster and accelerate the progress of this Science Mission Directorate research strategy over the coming years.

  4. Preliminary Flight Results of the Microelectronics and Photonics Test Bed: NASA DR1773 Fiber Optic Data Bus Experiment

    Science.gov (United States)

    Jackson, George L.; LaBel, Kenneth A.; Marshall, Cheryl; Barth, Janet; Seidleck, Christina; Marshall, Paul

    1998-01-01

    NASA Goddard Spare Flight Center's (GSFC) Dual Rate 1773 (DR1773) Experiment on the Microelectronic and Photonic Test Bed (MPTB) has provided valuable information on the performance of the AS 1773 fiber optic data bus in the space radiation environment. Correlation of preliminary experiment data to ground based radiation test results show the AS 1773 bus is employable in future spacecraft applications requiring radiation tolerant communication links.

  5. Testing of downstream catalysts for tar destruction with a guard bed in a fluidised bed biomass gasifier at pilot plant scale

    Energy Technology Data Exchange (ETDEWEB)

    Aznar, M.P.; Frances, E.; Campos, I.J.; Martin, J.A.; Gil, J. [Saragossa Univ. (Spain). Dept. of Chemistry and Environment Engineering; Corella, J. [Complutense Univ. of Madrid (Spain). Dept. of Chemical Engineering

    1996-12-31

    A new pilot plant for advanced gasification of biomass in a fast fluidised bed is now fully operative at University of Saragossa, Spain. It is a `3rd generation` pilot plant. It has been built up after having used two previous pilot plants for biomass gasification. The main characteristic of this pilot plant is that it has two catalytic reactors connected in series, downstream the biomass gasifier. Such reactors, of 4 cm i.d., are placed in a slip stream in a by-pass from the main gasifier exit gas. The gasification is made at atmospheric pressure, with flow rates of 3-50 kg/in, using steam + O{sub 2} mixtures as the gasifying agent. Several commercial Ni steam-reforming catalyst are being tested under a realistic raw gas composition. Tar eliminations or destructions higher than 99 % are easily achieved. (orig.) 2 refs.

  6. Mars ecopoiesis test bed: on earth and on the red planet

    Science.gov (United States)

    Todd, Paul; Kurk, Michael Andy; Boland, Eugene; Thomas, David; Scherzer, Christopher

    2016-07-01

    The concept of autotrophic organisms serving as planetary pioneers as a precursor to terraforming has been under consideration for several decades, and the term Ecopoiesis was introduced by the ecopoiets C. Sagan, M. Avener, R. Haynes and C. McKay to call attention to this possibility. There is a continuing need for experimental evidence to support this concept, one of them being the need to evaluate the survivability of terrestrial autotrophic microbes in a planetary environment. For this and other purposes a planetary simulation facility was constructed and operated at Techshot, Inc. in Indiana, USA. This facility has an accumulated record of more than one year's worth of experimentation under simulated Mars conditions. In a recent study this facility was operated for five weeks in a mode that simulated 35 sols on and just below the surface of Mars at low latitude. The diurnal lighting period was 12 hours:12 hours using xenon arc light filtered to simulate the solar intensity and spectrum on the Martian surface. A daily temperature profile followed that recorded at low latitudes with night-time minima at -80 C and noontime maxima at +26 C. Atmosphere was CO _{2} at <11 mbar. Moisture was monitored to confirm that no water could exist in the liquid phase. Test organisms included the cyanobacteria Anabena, sp., Chroococcidiopsis CCMEE171 and Plectonema boryanum and Eukaryota: Chlorella ellipsoidia maintained in the simulator under the above-described conditions. The exposed specimens were tested for intracellular esterase activity, chlorophyll content and reproductive survival. All tests yielded low-level positive survival results for these organisms. No definitive data relating to function and/or growth during exposure were sought. In parallel to these terrestrial studies a planned design study was undertaken for a proposed test bed to be operated on the surface of Mars. Design requirements include compact assembly for transport and installation on the planetary

  7. Implementation of an Electric Vehicle Test Bed Controlled by a Virtual Power Plant for Contributing to Regulating Power Reserves

    DEFF Research Database (Denmark)

    Marra, Francesco; Sacchetti, Dario; Pedersen, Anders Bro

    2012-01-01

    as a multifunctional grid-interactive EV, which a Virtual Power Plant (VPP) or a generic EV coordinator could use for testing different control strategies, such as EV contribution to regulating power reserves. The EV coordination is realized using the IEC 61850 modeling standard in the communication. Regulating power......With the increased focus on Electric Vehicles (EV) research and the potential benefits they bring for smart grid applications, there is a growing need for an evaluation platform connected to the electricity grid. This paper addresses the design of an EV test bed, which using real EV components...... and communication interfaces, is able to respond in real-time to smart grid control signals. The EV test bed is equipped with a Lithium-ion battery pack, a Battery Management System (BMS), a charger and a Vehicle-to-Grid (V2G) unit for feeding power back to the grid. The designed solution serves...

  8. A Method to Derive Monitoring Variables for a Cyber Security Test-bed of I and C System

    Energy Technology Data Exchange (ETDEWEB)

    Han, Kyung Soo; Song, Jae Gu; Lee, Joung Woon; Lee, Cheol Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    In the IT field, monitoring techniques have been developed to protect the systems connected by networks from cyber attacks and incidents. For the development of monitoring systems for I and C cyber security, it is necessary to review the monitoring systems in the IT field and derive cyber security-related monitoring variables among the proprietary operating information about the I and C systems. Tests for the development and application of these monitoring systems may cause adverse effects on the I and C systems. To analyze influences on the system and safely intended variables, the construction of an I and C system Test-bed should be preceded. This article proposes a method of deriving variables that should be monitored through a monitoring system for cyber security as a part of I and C Test-bed. The surveillance features and the monitored variables of NMS(Network Management System), a monitoring technique in the IT field, were reviewed in section 2. In Section 3, the monitoring variables for an I and C cyber security were derived by the of NMS and the investigation for information used for hacking techniques that can be practiced against I and C systems. The monitoring variables of NMS in the IT field and the information about the malicious behaviors used for hacking were derived as expected variables to be monitored for an I and C cyber security research. The derived monitoring variables were classified into the five functions of NMS for efficient management. For the cyber security of I and C systems, the vulnerabilities should be understood through a penetration test etc. and an assessment of influences on the actual system should be carried out. Thus, constructing a test-bed of I and C systems is necessary for the safety system in operation. In the future, it will be necessary to develop a logging and monitoring system for studies on the vulnerabilities of I and C systems with test-beds.

  9. A framework for computer model validation with a stochastic traffic microsimulators as test-bed

    Energy Technology Data Exchange (ETDEWEB)

    Sacks, J.; Rouphail, N. M.; Park, B. B.

    2001-07-01

    The validation of computer (simulation) models is a crucial element in assessing their utility for science and for policy-making. Often discussed and sometimes practiced informally, the process is straightforward conceptually: data are collected that represent both the inputs and the outputs of the model, the model is run at those inputs, and the output is compared to field data. In reality, complications abound, field data may be expensive, scarce or noisy, the model may be so complex that only a few runs are possible, and uncertainly enters the process at every turn. Even though is inherently a statistical issue, model validation lacks a unifying statistical framework. The need to develop such a framework is compelling, even urgent. The use of computer models by scientists and planners is growing, costs of poor decisions are escalating: and increasing computing power, for both computational and data collection, is magnifying the scale of the issues. Building a framework for validation of computer models requires an assortment of procedures and considerations and recognition of the multiple stages in the development and use of the models. Verification, which encompasses procedures to assure that the computer code is bug-free, is often seen as a predecessor of validation whereas, in fact, it may be enmeshed with validation. Feedback from outcomes of steps in the validation process can impact model development through detection of flaws or gaps- the result is an intertwining of validation with development. We will focus on (the) five essential characteristics of a validation: context, data uncertainty. feedback, and prediction and use a traffic microsimulator model applied to the planning of traffic signal timing as a test-bed. Our goal is to draw attention to the many complexities that need to be considered in order to achieve a successful validation. (Author) 3 refs.

  10. The Indianapolis Flux Experiment (INFLUX: A test-bed for developing urban greenhouse gas emission measurements

    Directory of Open Access Journals (Sweden)

    Kenneth J. Davis

    2017-05-01

    Full Text Available The objective of the Indianapolis Flux Experiment (INFLUX is to develop, evaluate and improve methods for measuring greenhouse gas (GHG emissions from cities. INFLUX’s scientific objectives are to quantify CO2 and CH4 emission rates at 1 km2 resolution with a 10% or better accuracy and precision, to determine whole-city emissions with similar skill, and to achieve high (weekly or finer temporal resolution at both spatial resolutions. The experiment employs atmospheric GHG measurements from both towers and aircraft, atmospheric transport observations and models, and activity-based inventory products to quantify urban GHG emissions. Multiple, independent methods for estimating urban emissions are a central facet of our experimental design. INFLUX was initiated in 2010 and measurements and analyses are ongoing. To date we have quantified urban atmospheric GHG enhancements using aircraft and towers with measurements collected over multiple years, and have estimated whole-city CO2 and CH4 emissions using aircraft and tower GHG measurements, and inventory methods. Significant differences exist across methods; these differences have not yet been resolved; research to reduce uncertainties and reconcile these differences is underway. Sectorally- and spatially-resolved flux estimates, and detection of changes of fluxes over time, are also active research topics. Major challenges include developing methods for distinguishing anthropogenic from biogenic CO2 fluxes, improving our ability to interpret atmospheric GHG measurements close to urban GHG sources and across a broader range of atmospheric stability conditions, and quantifying uncertainties in inventory data products. INFLUX data and tools are intended to serve as an open resource and test bed for future investigations. Well-documented, public archival of data and methods is under development in support of this objective.

  11. Route Optimization via RSSI APPs in Indoor Proxy Mobile IPv6 Test-bed

    Directory of Open Access Journals (Sweden)

    Nur Haliza Abdul Wahab

    2014-08-01

    Full Text Available Traditionally IP mobility support mechanisms, Mobile IPv4 or Mobile IPv6 are based on the host-based solution to keep on going sessions despite the movement. The current trend is towards networks-based solutions where mobility support is based on network operation. Proxy Mobile IPv6 (PMIPv6 has been developed by the Internet Engineering Task Force (IETF as a network-based mobility management protocol. The development is aimed to guarantee and support mobility for IP devices or called as Mobile Node (MN without the MN involving in any IP layer mobility related to signaling as stated in RFC5213. PMIPv6 in RFC5213 address the needed to enable Localized Routing (LR but it not specify a complete procedure to establish Route Optimization (RO. Data packets belong to MN need to travel to Local Mobility Anchor (LMA via bidirectional tunnel between Mobile Access Gateway (MAG and LMA. This result to long end to end delay. This un-optimized route result in increasing signaling data delay, huge handover latency, large transport cost and many more. Therefore, it important to optimized the data path so that the data destined to MN will be traverse using the shorter path or directly change traffic tunnel between MAG. As for this, the aims of this study are to reduce the handover latency and optimized data route by the illustration of development the PMIPv6 test-bed with implementation of RO via RSSI APPs. Several experiment will be discuss to see the performance of RO algorithm via RSSI APPs with non-optimized RO.

  12. Load converter interactions with the secondary system in the Space Station Freedom power management and distribution dc test bed

    Science.gov (United States)

    Lebron, Ramon C.

    1992-01-01

    The NASA LeRC in Cleveland, Ohio, is responsible for the design, development, and assembly of the Space Station Freedom (SSF) Electrical Power System (EPS). In order to identify and understand system level issues during the SSF program design and development phases, a system Power Management and Distribution (PMAD) dc test bed was assembled. Some of the objectives of this test bed facility are the evaluation of, system efficiency, power quality, system stability, and system protection and reconfiguration schemes. In order to provide a realistic operating scenario, dc Load Converter Units are used in the PMAD dc test bed to characterize the user interface with the power system. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. This final regulation is required on the actual space station because the majority of user loads will require voltage levels different from the secondary bus voltage. This paper describes the testing of load converters in an end to end system environment (from solar array to loads) where their interactions and compatibility with other system components are considered. Some of the system effects of interest that are presented include load converters transient behavior interactions with protective current limiting switchgear, load converters ripple effects, and the effects of load converter constant power behavior with protective features such as foldback.

  13. Load converter interactions with the secondary system in the Space Station Freedom power management and distribution DC test bed

    Science.gov (United States)

    Lebron, Ramon C.

    1992-01-01

    The NASA LeRC in Cleveland, Ohio, is responsible for the design, development, and assembly of the Space Station Freedom (SSF) Electrical Power System (EPS). In order to identify and understand system level issues during the SSF Program design and development phases, a system Power Management and Distribution (PMAD) DC test bed was assembled. Some of the objectives of this test bed facility are the evaluation of, system efficiency, power quality, system stability, and system protection and reconfiguration schemes. In order to provide a realistic operating scenario, dc Load Converter Units are used in the PMAD dc test bed to characterize the user interface with the power system. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. This final regulation is required on the actual space station because the majority of user loads will require voltage levels different from the secondary bus voltage. This paper describes the testing of load converters in an end to end system environment (from solar array to loads) where their interactions and compatibility with other system components are considered. Some of the system effects of interest that are presented include load converters transient behavior interactions with protective current limiting switchgear, load converters ripple effects, and the effects of load converter constant power behavior with protective features such as foldback.

  14. Sequestration and Enhanced Coal Bed Methane: Tanquary Farms Test Site, Wabash County, Illinois

    Energy Technology Data Exchange (ETDEWEB)

    Frailey, Scott; Parris, Thomas; Damico, James; Okwen, Roland; McKaskle, Ray; Monson, Charles; Goodwin, Jonathan; Beck, E; Berger, Peter; Butsch, Robert; Garner, Damon; Grube, John; Hackley, Keith; Hinton, Jessica; Iranmanesh, Abbas; Korose, Christopher; Mehnert, Edward; Monson, Charles; Roy, William; Sargent, Steven; Wimmer, Bracken

    2012-05-01

    The Midwest Geological Sequestration Consortium (MGSC) carried out a pilot project to test storage of carbon dioxide (CO{sub 2}) in the Springfield Coal Member of the Carbondale Formation (Pennsylvanian System), in order to gauge the potential for large-scale CO{sub 2} sequestration and/or enhanced coal bed methane recovery from Illinois Basin coal beds. The pilot was conducted at the Tanquary Farms site in Wabash County, southeastern Illinois. A four-well design an injection well and three monitoring wells was developed and implemented, based on numerical modeling and permeability estimates from literature and field data. Coal cores were taken during the drilling process and were characterized in detail in the lab. Adsorption isotherms indicated that at least three molecules of CO{sub 2} can be stored for each displaced methane (CH{sub 4}) molecule. Microporosity contributes significantly to total porosity. Coal characteristics that affect sequestration potential vary laterally between wells at the site and vertically within a given seam, highlighting the importance of thorough characterization of injection site coals to best predict CO{sub 2} storage capacity. Injection of CO{sub 2} gas took place from June 25, 2008, to January 13, 2009. A continuous injection period ran from July 21, 2008, to December 23, 2008, but injection was suspended several times during this period due to equipment failures and other interruptions. Injection equipment and procedures were adjusted in response to these problems. Approximately 92.3 tonnes (101.7 tons) of CO{sub 2} were injected over the duration of the project, at an average rate of 0.93 tonne (1.02 tons) per day, and a mode injection rate of 0.6-0.7 tonne/day (0.66-0.77 ton/day). A Monitoring, Verification, and Accounting (MVA) program was set up to detect CO{sub 2 leakage. Atmospheric CO{sub 2} levels were monitored as were indirect indicators of CO{sub 2} leakage such as plant stress, changes in gas composition at

  15. An examination of vehicles at the brake-chassis test bed in the range of the partial engine load

    Directory of Open Access Journals (Sweden)

    Paweł MARZEC

    2017-06-01

    Full Text Available The performance of a ZI engine is presented in the paper, as well as a project involving a device for applying a partial load in the performed examinations of a brakechassis test bed. The device was prepared for an Opel Astra and enabled the determination of exterior characteristics of the engine for different values of the engine load. The indicating pressure sensor and the angle marker on the crankshaft allowed for the recording of the indicating pressure obtained at different values of the load. The analysis of heat evolution in the process of burning, based on the registered results of the measurements at the brake-chassis test bed, has also been included in the presentation.

  16. Geo-energy Test Beds: part of the European Plate Observing System

    Science.gov (United States)

    Stephenson, Michael; Schofield, David; Luton, Christopher; Haslinger, Florian; Henninges, Jan; Giardini, Domenico

    2016-04-01

    For 2020, the EU has committed to cutting its greenhouse gas emissions to 20% below 1990 levels and further cuts are being decided for 2050. This commitment is one of the headline targets of the Europe 2020 growth strategy and is being implemented through binding legislation. This decarbonisation of the EU economy is one dimension of an overall EU energy and climate framework that is mutually interlinked with the need to ensure energy security, promote a fully integrated energy market, promote energy efficiency and promote research innovation and competitiveness. Power generation will have to take a particularly large part in emissions reductions (-54 to -68% by 2030 and -93 to -99% by 2050), mainly by focussing on increasing surface renewables (wind, tidal and solar) but also on carbon capture and storage on fossil fuel and biofuel power plants, shale gas, nuclear and geothermal power. All the above generation technologies share common geological challenges around containment, safety and environmental sustainability. In a densely populated continent, this means that high levels of subsurface management are needed to fully realise the energy potential. In response to this need, across Europe, public and private sector funded, experimental test and monitoring facilities and infrastructures (Geo-energy Test Beds, GETB) are being developed. These GETB investigate the processes, technology and practices that facilitate the sustainable exploitation of Geo-energy resources and are of intense interest to the public and regulators alike. The vision of EPOS IP Work Package 17 (wp17) is to promote research and innovation in Geo-energy that reflects core European energy priorities through provision of virtual access to data and protocols and trans-national access to GETB experiments. This will be achieved through provision of access to continuous strategic observations, promotion of the integrated use of data and models from European GETB, development of underpinning research

  17. Recent Developments in the Design, Capabilities and Autonomous Operations of a Lightweight Surface Manipulation System and Test-bed

    Science.gov (United States)

    Dorsey, John T.; Jones, Thomas C.; Doggett, W. R.; Brady, Jeffrey S.; Berry, Felecia C.; Ganoe, George G.; Anderson, Eric; King, Bruce D.; Mercer, David C.

    2011-01-01

    The first generation of a versatile high performance device for performing payload handling and assembly operations on planetary surfaces, the Lightweight Surface Manipulation System (LSMS), has been designed and built. Over the course of its development, conventional crane type payload handling configurations and operations have been successfully demonstrated and the range of motion, types of operations and the versatility greatly expanded. This enhanced set of 1st generation LSMS hardware is now serving as a laboratory test-bed allowing the continuing development of end effectors, operational techniques and remotely controlled and automated operations. This paper describes the most recent LSMS and test-bed development activities, that have focused on two major efforts. The first effort was to complete a preliminary design of the 2nd generation LSMS that has the capability for limited mobility and can reposition itself between lander decks, mobility chassis, and fixed base locations. A major portion of this effort involved conducting a study to establish the feasibility of, and define, the specifications for a lightweight cable-drive waist joint. The second effort was to continue expanding the versatility and autonomy of large planetary surface manipulators using the 1st generation LSMS as a test-bed. This has been accomplished by increasing manipulator capabilities and efficiencies through both design changes and tool and end effector development. A software development effort has expanded the operational capabilities of the LSMS test-bed to include; autonomous operations based on stored paths, use of a vision system for target acquisition and tracking, and remote command and control over a communications bridge.

  18. Displacement Damage Effects in Solar Cells: Mining Damage From the Microelectronics and Photonics Test Bed Space Experiment

    Science.gov (United States)

    Hardage, Donna (Technical Monitor); Walters, R. J.; Morton, T. L.; Messenger, S. R.

    2004-01-01

    The objective is to develop an improved space solar cell radiation response analysis capability and to produce a computer modeling tool which implements the analysis. This was accomplished through analysis of solar cell flight data taken on the Microelectronics and Photonics Test Bed experiment. This effort specifically addresses issues related to rapid technological change in the area of solar cells for space applications in order to enhance system performance, decrease risk, and reduce cost for future missions.

  19. Countermeasures and Functional Testing in Head-Down Tilt Bed Rest (CFT 70)

    Science.gov (United States)

    Cromwell, Ronita L.

    2013-01-01

    This 70-day bed rest campaign was comprised of 6 integrated studies and conducted at the NASA Flight Analogs Research Unit (FARU). The FARU is located at the University of Texas Medical Branch, Galveston, Texas and is a satellite unit of the Institute for Translational Sciences - Clinical Research Center. This presentation will describe the FARU, discuss the utility of the bed rest platform for use in these studies, and introduce the studies that participated in the CFT 70 bed rest campaign. Information in this presentation will serve as the background for subsequent talks from each individual study. Individual study presentations will discuss preliminary results from completed subjects. Studies included in CFT70 were: ? Physiological Factors Contributing to Post Flight Changes in Functional Performance. J. Bloomberg, NASA ? Integrated Resistance and Aerobic Training Study. L. Ploutz-Snyder, USRA ? Testosterone Supplementation as a Countermeasure Against Musculoskeletal losses during Space Exploration. R. Urban, University of Texas Medical Branch ? Effects of Retronasal Smelling, Variety and Choice on Appetite & Satiety. J. Hunter, Cornell University ? AD ASTRA: Automated Detection of Attitudes and States through Transaction Recordings Analysis. C. Miller, Smart Information Flow Technologies, LLC ? Bed Rest as a Spaceflight Analog to Study Neuro-cognitive Changes: Extent, Longevity, and Neural Bases. R. Seidler, University of Michigan

  20. Effect of temperature in fluidized bed fast pyrolysis of biomass: oil quality assessment in test units

    NARCIS (Netherlands)

    Westerhof, Roel Johannes Maria; Brilman, Derk Willem Frederik; van Swaaij, Willibrordus Petrus Maria; Kersten, Sascha R.A.

    2010-01-01

    Pine wood was pyrolyzed in a 1 kg/h fluidized bed fast pyrolysis reactor that allows a residence time of pine wood particles up to 25 min. The reactor temperature was varied between 330 and 580 °C to study the effect on product yields and oil composition. Apart from the physical−chemical analysis, a

  1. Effect of Temperature in Fluidized Bed Fast Pyrolysis of Biomass: Oil Quality Assessment in Test Units

    NARCIS (Netherlands)

    Westerhof, R.J.M.; Brilman, D.W.F.; Swaaij, van W.P.M.; Kersten, S.R.A.

    2010-01-01

    Pine wood was pyrolyzed in a 1 kg/h fluidized bed fast pyrolysis reactor that allows a residence time of pine wood particles up to 25 min. The reactor temperature was varied between 330 and 580 °C to study the effect on product yields and oil composition. Apart from the physical−chemical analysis, a

  2. Improvement of non destructive infrared test bed SATIR for examination of actively cooled tungsten armour Plasma Facing Components

    Energy Technology Data Exchange (ETDEWEB)

    Vignal, N., E-mail: nicolas.vignal@cea.fr; Desgranges, C.; Cantone, V.; Richou, M.; Courtois, X.; Missirlian, M.; Magaud, Ph.

    2013-10-15

    Highlights: • Non destructive infrared techniques for control ITER like PFCs. • Reflective surface such as W induce a measurement temperature error. • Numerical data processing by evaluation of the local emissivity. • SATIR test bed can control metallic surface with low and variable emissivity. -- Abstract: For steady state (magnetic) thermonuclear fusion devices which need large power exhaust capability and have to withstand heat fluxes in the range 10–20 MW m{sup −2}, advanced Plasma Facing Components (PFCs) have been developed. The importance of PFCs for operating tokamaks requests to verify their manufacturing quality before mounting. SATIR is an IR test bed validated and recognized as a reliable and suitable tool to detect cooling defaults on PFCs with CFC armour material. Current tokamak developments implement metallic armour materials for first wall and divertor; their low emissivity causes several difficulties for infrared thermography control. We present SATIR infrared thermography test bed improvements for W monoblocks components without defect and with calibrated defects. These results are compared to ultrasonic inspection. This study demonstrates that SATIR method is fully usable for PFCs with low emissivity armour material.

  3. The hydrological performance of a green roof test bed under UK climatic conditions

    Science.gov (United States)

    Stovin, Virginia; Vesuviano, Gianni; Kasmin, Hartini

    2012-01-01

    SummaryThis paper presents new rainfall and runoff data from a UK green roof test bed which has been collected almost-continuously over a 29-month period from 01/01/2007 to 31/05/2009. Overall, the monitoring period was fairly typical of the location's long-term climatic averages, although the data set includes some extreme events in June 2007, which were associated with serious flooding locally. To focus on the system's performance under rainfall events likely to be of interest from an urban drainage/stormwater management perspective, return period analysis has been applied to identify those storm events with a rainfall depth in excess of 5 mm and a return period greater than one year. According to these criteria, 22 significant events have been identified, of which 21 have reliable runoff records. Overall the roof provided 50.2% cumulative annual rainfall retention, with a total volumetric retention equivalent to 30% during the significant events. The annual performance figures are towards the lower end of a range of international data, probably reflecting the fact that rainfall depths may be higher and evapotranspiration rates lower than in some more continental climatic settings. The roof's finite retention depth means that the maximum possible retention percentage declines as storm depth increases, and retention varied from between 0 and 20 mm, or 0% to 100%. Although some attenuation and delay of peak runoff is generally observed (mean peak flow reduction of 60% for the 21 significant events), the irregularity of natural rainfall patterns, combined with the variable influence of detention storage in specific events, makes the identification of peak-to-peak lag times difficult and arguably meaningless. Regression analyses have been undertaken to explore the potential to predict the roof's hydrological performance as a function of storm characteristics. However, these are shown to have poor predictive capability, even for the system from which they were derived

  4. First results of the Test-Bed Telescopes (TBT) project: Cebreros telescope commissioning

    Science.gov (United States)

    Ocaña, Francisco; Ibarra, Aitor; Racero, Elena; Montero, Ángel; Doubek, Jirí; Ruiz, Vicente

    2016-07-01

    The TBT project is being developed under ESA's General Studies and Technology Programme (GSTP), and shall implement a test-bed for the validation of an autonomous optical observing system in a realistic scenario within the Space Situational Awareness (SSA) programme of the European Space Agency (ESA). The goal of the project is to provide two fully robotic telescopes, which will serve as prototypes for development of a future network. The system consists of two telescopes, one in Spain and the second one in the Southern Hemisphere. The telescope is a fast astrograph with a large Field of View (FoV) of 2.5 x 2.5 square-degrees and a plate scale of 2.2 arcsec/pixel. The tube is mounted on a fast direct-drive mount moving with speed up to 20 degrees per second. The focal plane hosts a 2-port 4K x 4K back-illuminated CCD with readout speeds up to 1MHz per port. All these characteristics ensure good survey performance for transients and fast moving objects. Detection software and hardware are optimised for the detection of NEOs and objects in high Earth orbits (objects moving from 0.1-40 arcsec/second). Nominal exposures are in the range from 2 to 30 seconds, depending on the observational strategy. Part of the validation scenario involves the scheduling concept integrated in the robotic operations for both sensors. Every night it takes all the input needed and prepares a schedule following predefined rules allocating tasks for the telescopes. Telescopes are managed by RTS2 control software, that performs the real-time scheduling of the observation and manages all the devices at the observatory.1 At the end of the night the observing systems report astrometric positions and photometry of the objects detected. The first telescope was installed in Cebreros Satellite Tracking Station in mid-2015. It is currently in the commissioning phase and we present here the first results of the telescope. We evaluate the site characteristics and the performance of the TBT Cebreros

  5. Analysis of Wave Predictions from the Coastal Model Test Bed using Operationally Estimated Bathymetry

    Science.gov (United States)

    Bak, S.; Smith, J. M.; Hesser, T.; Bryant, M. A.

    2016-12-01

    Near-coast wave models are generally validated with relatively small data sets that focus on analytical solutions, specialized experiments, or intense storms. Prior studies have compiled testbeds that include a few dozen experiments or storms to validate models (e.g., Ris et al. 2002), but few examples exist that allow for continued model evaluation in the nearshore and surf-zone in near-realtime. The limited nature of these validation sets is driven by a lack of high spatial and temporal resolution in-situ wave measurements and the difficulty in maintaining these instruments on the active profile over long periods of time. The US Army Corps of Engineers Field Research Facility (FRF) has initiated a Coastal Model Test-Bed (CMTB), which is an automated system that continually validates wave models (with morphological and circulation models to follow) utilizing the rich data set of oceanographic and bathymetric measurements collected at the FRF. The FRF's cross-shore wave array provides wave measurements along a cross-shore profile from 26 m of water depth to the shoreline, utilizing various instruments including wave-rider buoys, AWACs, aquadopps, pressure gauges, and a dune-mounted lidar (Brodie et al. 2015). This work uses the CMTB to evaluate the performance of a phase-averaged numerical wave model, STWAVE (Smith 2007, Massey et al. 2011) over the course of a year at the FRF in Duck, NC. Additionally, from the BathyDuck Experiment in October 2015, the CMTB was used to determine the impact of applying the depth boundary condition for the model from monthly acoustic bathymetric surveys in comparison to hourly estimates using a video-based inversion method (e.g., cBathy, Holman et al. 2013). The modeled wave parameters using both bathymetric boundary conditions are evaluated using the FRF's cross-shore wave array and two additional cross-shore arrays of wave measurements in 2 to 4 m water depth from BathyDuck in Fall, 2015.

  6. PMU Data Integrity Evaluation through Analytics on a Virtual Test-Bed

    Energy Technology Data Exchange (ETDEWEB)

    Olama, Mohammed M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shankar, Mallikarjun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-01-01

    Power systems are rapidly becoming populated by phasor measurement units (PMUs) in ever increasing numbers. PMUs are critical components of today s energy management systems, designed to enable near real-time wide area monitoring and control of the electric power system. They are able to measure highly accurate bus voltage phasors as well as branch current phasors incident to the buses at which PMUs are equipped. Synchrophasor data is used for applications varying from state estimation, islanding control, identifying outages, voltage stability detection and correction, disturbance recording, and others. However, PMU-measured readings may suffer from errors due to meter biases or drifts, incorrect configurations, or even cyber-attacks. Furthermore, the testing of early PMUs showed a large disparity between the reported values from PMUs provided by different manufacturers, particularly when frequency was off-nominal, during dynamic events, and when harmonic/inter-harmonic content was present. Detection and identification of PMU gross measurement errors are thus crucial in maintaining highly accurate phasor readings throughout the system. In this paper, we present our work in conducting analytics to determine the trustworthiness and worth of the PMU readings collected across an electric network system. By implementing the IEEE 118 bus test case on a virtual test bed (VTB) , we are able to emulate PMU readings (bus voltage and branch current phasors in addition to bus frequencies) under normal and abnormal conditions using (virtual) PMU sensors deployed across major substations in the network. We emulate a variety of failures such as bus, line, transformer, generator, and/or load failures. Data analytics on the voltage phase angles and frequencies collected from the PMUs show that specious (or compromised) PMU device(s) can be identified through abnormal behaviour by comparing the trend of its frequency and phase angle reading with the ensemble of all other PMU

  7. Beta spectrum of unique first-forbidden decays as a novel test for fundamental symmetries

    CERN Document Server

    Glick-Magid, Ayala; Mukul, Ish; Hass, Michael; Ron, Guy; Vaintraub, Sergey; Gazit, Doron

    2016-01-01

    Within the Standard Model, the weak interaction of quarks and leptons is characterized by certain symmetry properties, such as maximal breaking of parity and favored helicity. These are related to the $V-A$ structure of the weak interaction. These characteristics were discovered by studying correlations in the directions of the outgoing leptons in nuclear beta decays. These days, correlation measurements in nuclear beta decays are intensively studied to probe for signatures for deviations from these symmetries, which are an indication of Beyond Standard Model physics. We show that the structure of the energy spectrum of emitted electrons in unique first-forbidden $\\beta$-decays is sensitive to the symmetries of the weak interaction, and thus can be used as a novel probe of physics beyond the standard model. Furthermore, the energy spectrum gives constraints both in the case of right and left coupling of the new symmetry currents. We show that a measurement with modest energy resolution of about 20 keV is expe...

  8. Testing and verification of granular-bed filters for the removal of particulate and alkalis. Tenth quarterly project report, January 1-March 31, 1983

    Energy Technology Data Exchange (ETDEWEB)

    Lippert, T.E.

    1983-01-01

    The Westinghouse Electric Corporation with Ducon, Inc. and Burns and Roe, Inc. are conducting a test and evaluation program of a Granular-Bed Filter (GBF) for gas-cleaning applications in pressurized-fluidized-bed combustion processes. This work is funded by DOE PRDA for Exploratory Research, Development, Testing and Evaluation of Systems or Devices for Hot Gas Clean-up. This report describes the status of the testing of the subpilot scale GBF unit under simulated Pressurized-Fluidized-Bed Combustion (PFBC) conditions through Phase IV. 9 references, 21 figures, 4 tables.

  9. An Envision of Low Cost Mobile Adhoc Network Test Bed in a Laboratory Environment Emulating an Actual MANET

    Directory of Open Access Journals (Sweden)

    Nitiket N Mhala

    2010-05-01

    Full Text Available Orchestrating a live field trial of wireless mobile networking involves significant cost andlogistical issues relating to mobile platforms, support personnel, network and experiment automation andsupport equipment. The significant cost and logistics required to execute such a field trial can also belimiting in terms of achieving meaningful test results that exercise a practical number of mobile nodesover a significant set of test conditions within a given time. There is no argument that field trials are animportant component of dynamic network testing. A field test of prototype will show whether simulationswere on right track or not, but that’s a big leap to take; going from the simulator directly to the realthing. In conceiving our work, we envisioned a mobile network emulation system that is low cost, flexibleand controllable. This paper describes our wireless MANET test bed under development which emulatesan actual MANET. Here, we focuses that, this test bed allows the users to automatically generatearbitrary logically network topologies in order to perform real time operations on adhoc network at arelatively low cost in a laboratory environment without having to physically move the nodes in the adhocnetwork. Thus, we try to “compress” wireless network so that it fits on a single table.

  10. An Optical Receiver Post-Processing System for the Integrated Radio and Optical Communications Software Defined Radio Test Bed

    Science.gov (United States)

    Nappier, Jennifer M.; Tokars, Roger P.; Wroblewski, Adam C.

    2016-01-01

    The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center is investigating the feasibility of a hybrid radio frequency (RF) and optical communication system for future deep space missions. As a part of this investigation, a test bed for a radio frequency (RF) and optical software defined radio (SDR) has been built. Receivers and modems for the NASA deep space optical waveform are not commercially available so a custom ground optical receiver system has been built. This paper documents the ground optical receiver, which is used in order to test the RF and optical SDR in a free space optical communications link.

  11. Resource Assessment & Production Testing for Coal Bed Methane in the Illinois Basin

    Energy Technology Data Exchange (ETDEWEB)

    Cortland Eble; James Drahovzal; David Morse; Ilham Demir; John Rupp; Maria Mastalerz; Wilfrido Solano

    2005-11-01

    In order to assess the economic coal bed methane potential of the Illinois Basin, the geological surveys of Illinois, Indiana and Kentucky performed a geological assessment of their respective parts of the Illinois Basin. A considerable effort went into generating cumulative coal thickness and bed structure maps to identify target areas for exploratory drilling. Following this, the first project well was drilled in White County, Illinois in October 2003. Eight additional wells were subsequently drilled in Indiana (3) and Kentucky (5) during 2004 and 2005. In addition, a five spot pilot completion program was started with three wells being completed. Gas contents were found to be variable, but generally higher than indicated by historical data. Gas contents of more than 300 scf/ton were recovered from one of the bore holes in Kentucky. Collectively, our findings indicate that the Illinois Basin represents a potentially large source of economic coal bed methane. Additional exploration will be required to refine gas contents and the economics of potential production.

  12. Development and Validation of a Lifecycle-based Prognostics Architecture with Test Bed Validation

    Energy Technology Data Exchange (ETDEWEB)

    Hines, J. Wesley [Univ. of Tennessee, Knoxville, TN (United States); Upadhyaya, Belle [Univ. of Tennessee, Knoxville, TN (United States); Sharp, Michael [Univ. of Tennessee, Knoxville, TN (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jeffries, Brien [Univ. of Tennessee, Knoxville, TN (United States); Nam, Alan [Univ. of Tennessee, Knoxville, TN (United States); Strong, Eric [Univ. of Tennessee, Knoxville, TN (United States); Tong, Matthew [Univ. of Tennessee, Knoxville, TN (United States); Welz, Zachary [Univ. of Tennessee, Knoxville, TN (United States); Barbieri, Federico [Univ. of Tennessee, Knoxville, TN (United States); Langford, Seth [Univ. of Tennessee, Knoxville, TN (United States); Meinweiser, Gregory [Univ. of Tennessee, Knoxville, TN (United States); Weeks, Matthew [Univ. of Tennessee, Knoxville, TN (United States)

    2014-11-06

    On-line monitoring and tracking of nuclear plant system and component degradation is being investigated as a method for improving the safety, reliability, and maintainability of aging nuclear power plants. Accurate prediction of the current degradation state of system components and structures is important for accurate estimates of their remaining useful life (RUL). The correct quantification and propagation of both the measurement uncertainty and model uncertainty is necessary for quantifying the uncertainty of the RUL prediction. This research project developed and validated methods to perform RUL estimation throughout the lifecycle of plant components. Prognostic methods should seamlessly operate from beginning of component life (BOL) to end of component life (EOL). We term this "Lifecycle Prognostics." When a component is put into use, the only information available may be past failure times of similar components used in similar conditions, and the predicted failure distribution can be estimated with reliability methods such as Weibull Analysis (Type I Prognostics). As the component operates, it begins to degrade and consume its available life. This life consumption may be a function of system stresses, and the failure distribution should be updated to account for the system operational stress levels (Type II Prognostics). When degradation becomes apparent, this information can be used to again improve the RUL estimate (Type III Prognostics). This research focused on developing prognostics algorithms for the three types of prognostics, developing uncertainty quantification methods for each of the algorithms, and, most importantly, developing a framework using Bayesian methods to transition between prognostic model types and update failure distribution estimates as new information becomes available. The developed methods were then validated on a range of accelerated degradation test beds. The ultimate goal of prognostics is to provide an accurate assessment for

  13. Development and Validation of a Lifecycle-based Prognostics Architecture with Test Bed Validation

    Energy Technology Data Exchange (ETDEWEB)

    Hines, J. Wesley [Univ. of Tennessee, Knoxville, TN (United States); Upadhyaya, Belle [Univ. of Tennessee, Knoxville, TN (United States); Sharp, Michael [Univ. of Tennessee, Knoxville, TN (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jeffries, Brien [Univ. of Tennessee, Knoxville, TN (United States); Nam, Alan [Univ. of Tennessee, Knoxville, TN (United States); Strong, Eric [Univ. of Tennessee, Knoxville, TN (United States); Tong, Matthew [Univ. of Tennessee, Knoxville, TN (United States); Welz, Zachary [Univ. of Tennessee, Knoxville, TN (United States); Barbieri, Federico [Univ. of Tennessee, Knoxville, TN (United States); Langford, Seth [Univ. of Tennessee, Knoxville, TN (United States); Meinweiser, Gregory [Univ. of Tennessee, Knoxville, TN (United States); Weeks, Matthew [Univ. of Tennessee, Knoxville, TN (United States)

    2014-11-06

    On-line monitoring and tracking of nuclear plant system and component degradation is being investigated as a method for improving the safety, reliability, and maintainability of aging nuclear power plants. Accurate prediction of the current degradation state of system components and structures is important for accurate estimates of their remaining useful life (RUL). The correct quantification and propagation of both the measurement uncertainty and model uncertainty is necessary for quantifying the uncertainty of the RUL prediction. This research project developed and validated methods to perform RUL estimation throughout the lifecycle of plant components. Prognostic methods should seamlessly operate from beginning of component life (BOL) to end of component life (EOL). We term this "Lifecycle Prognostics." When a component is put into use, the only information available may be past failure times of similar components used in similar conditions, and the predicted failure distribution can be estimated with reliability methods such as Weibull Analysis (Type I Prognostics). As the component operates, it begins to degrade and consume its available life. This life consumption may be a function of system stresses, and the failure distribution should be updated to account for the system operational stress levels (Type II Prognostics). When degradation becomes apparent, this information can be used to again improve the RUL estimate (Type III Prognostics). This research focused on developing prognostics algorithms for the three types of prognostics, developing uncertainty quantification methods for each of the algorithms, and, most importantly, developing a framework using Bayesian methods to transition between prognostic model types and update failure distribution estimates as new information becomes available. The developed methods were then validated on a range of accelerated degradation test beds. The ultimate goal of prognostics is to provide an accurate assessment for

  14. Tailoring clinical services to address the unique needs of adolescents from the pregnancy test to parenthood.

    Science.gov (United States)

    Moriarty Daley, Alison; Sadler, Lois S; Dawn Reynolds, Heather

    2013-04-01

    Clinicians across disciplines and practice settings are likely to encounter adolescents who are at risk for a pregnancy. In 2010, 34.2/1000 15-19-year-old teens had a live birth in the United States, many more will seek care for a pregnancy scare or options counseling. Teen mothers are also at risk for a second or higher-order pregnancy during adolescence. This paper provides clinicians with adolescent-friendly clinical and counseling strategies for pregnancy prevention, pre- and post-pregnancy test counseling, pregnancy-related care, and a review of the developmental challenges encountered by teens in the transition to parenthood. Clinicians are in a better position to approach the developmental, health and mental health needs of adolescents related to pregnancy if they understand and appreciate the obstacles adolescents may face negotiating the healthcare system. In addition, when clinical services are specially tailored to the needs of the adolescent, fewer opportunities will be lost to prevent unintended pregnancies, assist teens into timely prenatal services, and improve outcomes for their pregnancies and the transition to parenthood.

  15. Bed Bugs

    Science.gov (United States)

    Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

  16. A unique laboratory test rig reduces the need for offshore tests to combat calcium naphthenate deposition in oilfield process equipment.

    Energy Technology Data Exchange (ETDEWEB)

    Mediaas, Heidi; Grande, Knut; Hustad, Britt-Marie; Hoevik, Kim Reidar; Kummernes, Hege; Nergaard, Bjoern; Vindstad, Jens Emil

    2006-03-15

    Producing and refining high-TAN crude oils introduces a number of challenges, among which calcium naphthenate deposition in process facilities is the most serious production issue. Until recently, the only option for studying chemicals and process parameters in order to prevent naphthenate deposition has been field tests. Statoil has now developed a small scale pilot plant where these experiments can be performed in the laboratory at Statoil's Research and Technology Center in Trondheim, Norway. The results from the pilot plant are in full agreement with the extensive naphthenate experience obtained from almost 9 years operation of the Heidrun oilfield. The design and operational procedures for this test facility are based on the recent discovery by Statoil and ConocoPhillips of the ARN acid. The ARN acid is a prerequisite for calcium naphthenate deposition. The new continuous flow pilot plant, the Naphthenate Rig, is used to develop new environmental friendly naphthenate inhibitors and to optimize process operating conditions. Since it operates on real crudes the need for field tests in qualifying new naphthenate inhibitors is reduced. To the best of our knowledge, the rig is the first of its kind in the world. (Author)

  17. Materials problems in fluidized-bed combustion systems. Appendix 2. Test specimen preparation, handling, and posttest evaluation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, E.A.; Holder, J.C.; Minchener, A.J.; Page, A.J.; La Nauze, R.D.

    1980-05-01

    Appendix 2 presents the metallographic data compiled by the National Coal Board, Coal Research Establishment, on materials tested for the Electric Power Research Institute Contract R P 388-1 with Combustion Systems Ltd., UK. Two 1000 h tests were carried out to investigate the corrosion performance of boiler and gas turbine alloys exposed in and above a fluidised bed coal combustor. Details are given of the preparation, handling, and examination procedures. Results of metallographic examination and chemical analyses on the samples examined by CRE are provided. This appendix does not attempt to draw any conclusions from the data: such conclusions appear in the main report. Description of the tests and plant performance data are given in Appendix 1 of this report.

  18. CO2 Absorption in a Lab-Scale Fixed Solid Bed Reactor: Modelling and Experimental Tests

    Directory of Open Access Journals (Sweden)

    Roberto Gabbrielli

    2004-09-01

    Full Text Available The CO2 absorption in a lab-scale fixed solid bed reactor filled with different solid sorbents has been studied under different operative conditions regarding temperature (20-200°C and input gas composition (N2, O2, CO2, H2O at 1bar pressure. The gas leaving the reactor has been analysed to measure the CO2 and O2 concentrations and, consequently, to evaluate the overall CO2 removal efficiency. In order to study the influence of solid sorbent type (i.e. CaO, coal bottom ash, limestone and blast furnace slag and of mass and heat transfer processes on CO2 removal efficiency, a one-dimensional time dependent mathematical model of the reactor, which may be considered a Plug Flow Reactor, has been developed. The quality of the model has been confirmed using the experimental results.

  19. Development of an Indoor Location Based Service Test Bed and Geographic Information System with a Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Shau-Shiun Jan

    2010-03-01

    Full Text Available In order to provide the seamless navigation and positioning services for indoor environments, an indoor location based service (LBS test bed is developed to integrate the indoor positioning system and the indoor three-dimensional (3D geographic information system (GIS. A wireless sensor network (WSN is used in the developed indoor positioning system. Considering the power consumption, in this paper the ZigBee radio is used as the wireless protocol, and the received signal strength (RSS fingerprinting positioning method is applied as the primary indoor positioning algorithm. The matching processes of the user location include the nearest neighbor (NN algorithm, the K-weighted nearest neighbors (KWNN algorithm, and the probabilistic approach. To enhance the positioning accuracy for the dynamic user, the particle filter is used to improve the positioning performance. As part of this research, a 3D indoor GIS is developed to be used with the indoor positioning system. This involved using the computer-aided design (CAD software and the virtual reality markup language (VRML to implement a prototype indoor LBS test bed. Thus, a rapid and practical procedure for constructing a 3D indoor GIS is proposed, and this GIS is easy to update and maintenance for users. The building of the Department of Aeronautics and Astronautics at National Cheng Kung University in Taiwan is used as an example to assess the performance of various algorithms for the indoor positioning system.

  20. Development of an indoor location based service test bed and geographic information system with a wireless sensor network.

    Science.gov (United States)

    Jan, Shau-Shiun; Hsu, Li-Ta; Tsai, Wen-Ming

    2010-01-01

    In order to provide the seamless navigation and positioning services for indoor environments, an indoor location based service (LBS) test bed is developed to integrate the indoor positioning system and the indoor three-dimensional (3D) geographic information system (GIS). A wireless sensor network (WSN) is used in the developed indoor positioning system. Considering the power consumption, in this paper the ZigBee radio is used as the wireless protocol, and the received signal strength (RSS) fingerprinting positioning method is applied as the primary indoor positioning algorithm. The matching processes of the user location include the nearest neighbor (NN) algorithm, the K-weighted nearest neighbors (KWNN) algorithm, and the probabilistic approach. To enhance the positioning accuracy for the dynamic user, the particle filter is used to improve the positioning performance. As part of this research, a 3D indoor GIS is developed to be used with the indoor positioning system. This involved using the computer-aided design (CAD) software and the virtual reality markup language (VRML) to implement a prototype indoor LBS test bed. Thus, a rapid and practical procedure for constructing a 3D indoor GIS is proposed, and this GIS is easy to update and maintenance for users. The building of the Department of Aeronautics and Astronautics at National Cheng Kung University in Taiwan is used as an example to assess the performance of various algorithms for the indoor positioning system.

  1. Design and construction of an optical test bed for LISA imaging systems and tilt-to-length coupling

    Science.gov (United States)

    Chwalla, M.; Danzmann, K.; Fernández Barranco, G.; Fitzsimons, E.; Gerberding, O.; Heinzel, G.; Killow, C. J.; Lieser, M.; Perreur-Lloyd, M.; Robertson, D. I.; Schuster, S.; Schwarze, T. S.; Tröbs, M.; Ward, H.; Zwetz, M.

    2016-12-01

    The laser interferometer space antenna (LISA) is a future space-based interferometric gravitational-wave detector consisting of three spacecraft in a triangular configuration. The interferometric measurements of path length changes between satellites will be performed on optical benches in the satellites. Angular misalignments of the interfering beams couple into the length measurement and represent a significant noise source. Imaging systems will be used to reduce this tilt-to-length coupling. We designed and constructed an optical test bed to experimentally investigate tilt-to-length coupling. It consists of two separate structures, a minimal optical bench and a telescope simulator. The minimal optical bench comprises the science interferometer where the local laser is interfered with light from a remote spacecraft. In our experiment, a simulated version of this received beam is generated on the telescope simulator. The telescope simulator provides a tilting beam, a reference interferometer and an additional static beam as a phase reference. The tilting beam can either be a flat-top beam or a Gaussian beam. We avoid tilt-to-length coupling in the reference interferometer by using a small photo diode placed at an image of the beam rotation point. We show that the test bed is operational with an initial measurement of tilt-to-length coupling without imaging systems. Furthermore, we show the design of two different imaging systems whose performance will be investigated in future experiments.

  2. FEASIBILITY STUDY FOR THE DEVELOPMENT OF A TEST BED PROGRAM FOR NOVEL DETECTORS AND DETECTOR MATERIALS AT SRS H-CANYON SEPARATIONS FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    Sexton, L.; Mendez-Torres, A.; Hanks, D.

    2011-06-07

    Researchers at the Savannah River National Laboratory (SRNL) have proposed that a test bed for advanced detectors be established at the H-Canyon separations facility located on the DOE Savannah River Site. The purpose of the proposed test bed will be to demonstrate the capabilities of emerging technologies for national and international safeguards applications in an operational environment, and to assess the ability of proven technologies to fill any existing gaps. The need for such a test bed has been expressed in the National Nuclear Security Administration's (NNSA) Next Generation Safeguards Initiative (NGSI) program plan and would serve as a means to facilitate transfer of safeguards technologies from the laboratory to an operational environment. New detectors and detector materials open the possibility of operating in a more efficient and cost effective manner, thereby strengthening national and international safeguards objectives. In particular, such detectors could serve the DOE and IAEA in improving timeliness of detection, minimizing uncertainty and improving confidence in results. SRNL's concept for the H Canyon test bed program would eventually open the facility to other DOE National Laboratories and establish a program for testing national and international safeguards related equipment. The initial phase of the test bed program is to conduct a comprehensive feasibility study to determine the benefits and challenges associated with establishing such a test bed. The feasibility study will address issues related to the planning, execution, and operation of the test bed program. Results from the feasibility study will be summarized and discussed in this paper.

  3. NASA Electric Aircraft Test Bed (NEAT) Development Plan - Design, Fabrication, Installation

    Science.gov (United States)

    Dyson, Rodger W.

    2016-01-01

    As large airline companies compete to reduce emissions, fuel, noise, and maintenance costs, it is expected that more of their aircraft systems will shift from using turbofan propulsion, pneumatic bleed power, and hydraulic actuation, to instead using electrical motor propulsion, generator power, and electrical actuation. This requires new flight-weight and flight-efficient powertrain components, fault tolerant power management, and electromagnetic interference mitigation technologies. Moreover, initial studies indicate some combination of ambient and cryogenic thermal management and relatively high bus voltages when compared to state of practice will be required to achieve a net system benefit. Developing all these powertrain technologies within a realistic aircraft architectural geometry and under realistic operational conditions requires a unique electric aircraft testbed. This report will summarize existing testbed capabilities located in the U.S. and details the development of a unique complementary testbed that industry and government can utilize to further mature electric aircraft technologies.

  4. Simultaneous calcium fluorescence imaging and MR of ex vivo organotypic cortical cultures: a new test bed for functional MRI.

    Science.gov (United States)

    Bai, Ruiliang; Klaus, Andreas; Bellay, Tim; Stewart, Craig; Pajevic, Sinisa; Nevo, Uri; Merkle, Hellmut; Plenz, Dietmar; Basser, Peter J

    2015-12-01

    Recently, several new functional (f)MRI contrast mechanisms including diffusion, phase imaging, proton density, etc. have been proposed to measure neuronal activity more directly and accurately than blood-oxygen-level dependent (BOLD) fMRI. However, these approaches have proved difficult to reproduce, mainly because of the dearth of reliable and robust test systems to vet and validate them. Here we describe the development and testing of such a test bed for non-BOLD fMRI. Organotypic cortical cultures were used as a stable and reproducible biological model of neuronal activity that shows spontaneous activity similar to that of in vivo brain cortex without any hemodynamic confounds. An open-access, single-sided magnetic resonance (MR) "profiler" consisting of four permanent magnets with magnetic field of 0.32 T was used in this study to perform MR acquisition. A fluorescence microscope with long working distance objective was mounted on the top of a custom-designed chamber that keeps the organotypic culture vital, and the MR system was mounted on the bottom of the chamber to achieve real-time simultaneous calcium fluorescence optical imaging and MR acquisition on the same specimen. In this study, the reliability and performance of the proposed test bed were demonstrated by a conventional CPMG MR sequence acquired simultaneously with calcium imaging, which is a well-characterized measurement of neuronal activity. This experimental design will make it possible to correlate directly the other candidate functional MR signals to the optical indicia of neuronal activity in the future.

  5. A social cybernetic analysis of simulation-based, remotely delivered medical skills training in an austere environment: developing a test bed for spaceflight medicine.

    Science.gov (United States)

    Musson, David M; Doyle, Thomas E

    2012-01-01

    This paper describes analysis of medical skills training exercises that were conducted at an arctic research station. These were conducted as part of an ongoing effort to establish high fidelity medical simulation test bed capabilities in remote and extreme "space analogue" environments for the purpose studying medical care in spaceflight. The methodological orientation followed by the authors is that of "second order cybernetics," or the science of studying human systems where the observer is involved within the system in question. Analyses presented include the identification of three distinct phases of the training activity, and two distinct levels of work groups-- termed "first-order teams" and "second-order teams." Depending on the phase of activity, first-order and second-order teams are identified, each having it own unique structure, composition, communications, goals, and challenges. Several specific teams are highlighted as case examples. Limitations of this approach are discussed, as are potential benefits to ongoing and planned research activity in this area.

  6. Design and construction of an optical test bed for eLISA imaging systems and tilt-to-length coupling

    CERN Document Server

    Chwalla, Michael; Barranco, Germán Fernández; Fitzsimons, Ewan; Gerberding, Oliver; Heinzel, Gerhard; Killow, Christian J; Lieser, Maike; Perreur-Lloyd, Michael; Robertson, David I; Schuster, Sönke; Schwarze, Thomas S; Tröbs, Michael; Ward, Henry; Zwetz, Max

    2016-01-01

    The evolved Laser Interferometer Space Antenna (eLISA) is a future space-based interferometric gravitational-wave detector consisting of three spacecraft in a triangular configuration. The interferometric measurements of path length changes between satellites will be performed on optical benches in the satellites. Angular misalignments of the interfering beams will couple into the length measurement and represent a significant noise source (tilt-to-length (TTL) coupling). Imaging systems are foreseen to reduce this TTL coupling. We have designed and built two different imaging systems to suppress this coupling. To investigate tilt-to-length coupling experimentally we designed and constructed an optical test bed. It consists of a minimal optical bench and a telescope simulator. The minimal optical bench comprises the science interferometer where the local laser is interfered with light from a remote spacecraft. In our experiment, a simulated version of this received beam is generated on the telescope simulator...

  7. EMERGING TECHNOLOGY BULLETIN: SPOUTED BED REACTOR

    Science.gov (United States)

    The Spouted Bed Reactor (SBR) technology utilizes the unique attributes of the "spouting " fluidization regime, which can provide heat transfer rates comparable to traditional fluid beds, while providing robust circulation of highly heterogeneous solids, concurrent with very agg...

  8. From bed to bench: Which attitude towards the laboratory liver tests should health care practitioners strike?

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    There is a general consensus in re-interpreting the so-called liver function tests in the light of novel discoveries. At the same time, recent evidence favours the use of different laboratory data to assess liver damage, fibrosis or regenerative process, but this point is not always shared. Actually, balancing the need for diagnosis, prognostic evaluation and therapy response of liver disease with a good cost/benefit ratio is very difficult. New tests are probably not needed but the aim should be for better utilization of existing tests to contain the increasing cost of health care.

  9. The development and testing of a unique and flexible training module for residents and fellows using digital breast tomosythesis (DBT)

    Science.gov (United States)

    Hakim, Christiane M.; Drescher, John; King, Jill L.; Logue, Durwin; Klym, Amy H.; Gur, David

    2017-03-01

    The transition from FFDM to digital breast tomosynthesis (DBT) necessitates new approaches for training radiology residents and fellows that highlight depiction differences between the same abnormalities on the two modalities. We developed a unique, flexible training module that enables training with complete feedback, as well as testing performance before and after use of this training module. Currently, 219 examinations, with priors and other relevant information, are included. Using a special interface to the Secure View workstation (Hologic), we developed a management program that displays each case in a randomized manner and in a sequential mode (i.e. FFDM first followed by FFDM+DBT) and allows the reader to rate the case followed by viewing the images side by side with results of the full imaging based history (reporting) by the screening interpreter, the diagnostic workup interpreter (when applicable), and the actual pathology (biopsy and/or surgical). This approach allows the reader to review their correct and/or incorrect interpretation at each step of the management decision making. The module also has sets of pre- and post-training cases, allowing for a test-train-test study to be performed, if so desired. Two observer studies using 18 radiologists, residents, and fellows have been performed using this module, to date. The training module was assembled, tested, and implemented. We found it to be extremely flexible and useful in training. After completing two observer performance studies, the module was installed in our clinical facility and is currently being used to train residents and fellows at their own pace. All users found this module to be useful and extremely informative.

  10. 2014 ITS World Congress Connected Vehicle Test Bed Demonstration Intersection Situation Data

    Data.gov (United States)

    Department of Transportation — During the 2014 ITS World Congress a demonstration of the connected vehicle infrastructure in the City of Detroit was conducted. The test site included approximately...

  11. 2014 ITS World Congress Connected Vehicle Test Bed Demonstration Traveler Situation Data

    Data.gov (United States)

    Department of Transportation — During the 2014 ITS World Congress a demonstration of the connected vehicle infrastructure in the City of Detroit was conducted. The test site included approximately...

  12. 2014 ITS World Congress Connected Vehicle Test Bed Demonstration Vehicle Situation Data

    Data.gov (United States)

    Department of Transportation — During the 2014 ITS World Congress a demonstration of the connected vehicle infrastructure in the City of Detroit was conducted. The test site included approximately...

  13. Test-bed for compact ventilation units; Pruefstand fuer Kompaktlueftungsgeraete fuer Komfortlueftung

    Energy Technology Data Exchange (ETDEWEB)

    Furter, R.; Helfenfinger, D.; Huber, H.; Wenger, L.

    2005-12-15

    This comprehensive, illustrated report for the Swiss Federal Office of Energy (SFOE) by the University of Applied Sciences in Lucerne, Switzerland takes a look at the testing facility at the university that is used to test compact ventilation systems. These feature heat-recovery and return-air heat-pumps and are used in housing built to low energy-consumption standards such as the Swiss 'Minergie' and 'Minergie-P' standards. The primary goal is a technically comprehensive testing programme for compact ventilation units with heat recovery and heat pumps, which can nevertheless be carried out at reasonable cost. In addition to thermal and flow measurements, acoustic measurements are also carried out. The authors quote that the overall assessment provided can also include service and maintenance, materials used and possible problems with thermal bridges. The test installation is described and the testing regulations used are elaborated, as are the various factors that can be measured and examined. First results are presented and a review of work to be done at the European level is discussed.

  14. 76 FR 22030 - Third Party Testing for Certain Children's Products; Toddler Beds: Requirements for Accreditation...

    Science.gov (United States)

    2011-04-20

    ..., private labeler, or other interested party to hide or exert undue influence over the third party... nation; The third party conformity assessment body's testing results are not subject to undue influence... undue influence over other governmental authorities on matters affecting its operations or on decisions...

  15. Multi-Column Experimental Test Bed Using CaSDB MOF for Xe/Kr Separation

    Energy Technology Data Exchange (ETDEWEB)

    Welty, Amy Keil [Idaho National Lab. (INL), Idaho Falls, ID (United States); Greenhalgh, Mitchell Randy [Idaho National Lab. (INL), Idaho Falls, ID (United States); Garn, Troy Gerry [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-03-01

    Processing of spent nuclear fuel produces off-gas from which several volatile radioactive components must be separated for further treatment or storage. As part of the Off-gas Sigma Team, parallel research at INL and PNNL has produced several promising sorbents for the selective capture of xenon and krypton from these off-gas streams. In order to design full-scale treatment systems, sorbents that are promising on a laboratory scale must be proven under process conditions to be considered for pilot and then full-scale use. To that end, a bench-scale multi-column system with capability to test multiple sorbents was designed and constructed at INL. This report details bench-scale testing of CaSDB MOF, produced at PNNL, and compares the results to those reported last year using INL engineered sorbents. Two multi-column tests were performed with the CaSDB MOF installed in the first column, followed with HZ-PAN installed in the second column. The CaSDB MOF column was placed in a Stirling cryocooler while the cryostat was employed for the HZ-PAN column. Test temperatures of 253 K and 191 K were selected for the first column while the second column was held at 191 K for both tests. Calibrated volume sample bombs were utilized for gas stream analyses. At the conclusion of each test, samples were collected from each column and analyzed for gas composition. While CaSDB MOF does appear to have good capacity for Xe, the short time to initial breakthrough would make design of a continuous adsorption/desorption cycle difficult, requiring either very large columns or a large number of smaller columns. Because of the tenacity with which Xe and Kr adhere to the material once adsorbed, this CaSDB MOF may be more suitable for use as a long-term storage solution. Further testing is recommended to determine if CaSDB MOF is suitable for this purpose.

  16. Dynamic Test Bed Analysis of Gas Energy Balance for a Diesel Exhaust System Fit with a Thermoelectric Generator

    Science.gov (United States)

    Fuc, Pawel; Lijewski, Piotr; Ziolkowski, Andrzej; Dobrzyński, Michal

    2017-02-01

    Analysis of the energy balance for an exhaust system of a diesel engine fit with an automotive thermoelectric generator (ATEG) of our own design has been carried out. A special measurement system and dedicated software were developed to measure the power generated by the modules. The research object was a 1.3-l small diesel engine with power output of 66 kW. The tests were carried out on a dynamic engine test bed that allows reproduction of an actual driving cycle expressed as a function V = f(t), simulating drivetrain (clutch, transmission) operating characteristics, vehicle geometrical parameters, and driver behavior. Measurements of exhaust gas thermodynamic parameters (temperature, pressure, and mass flow) as well as the voltage and current generated by the thermoelectric modules were performed during tests of our own design. Based on the results obtained, the flow of exhaust gas energy in the entire exhaust system was determined along with the ATEG power output. The ideal area of the exhaust system for location of the ATEG was defined to ensure the highest thermal energy recovery efficiency.

  17. Dynamic Test Bed Analysis of Gas Energy Balance for a Diesel Exhaust System Fit with a Thermoelectric Generator

    Science.gov (United States)

    Fuc, Pawel; Lijewski, Piotr; Ziolkowski, Andrzej; Dobrzyński, Michal

    2017-05-01

    Analysis of the energy balance for an exhaust system of a diesel engine fit with an automotive thermoelectric generator (ATEG) of our own design has been carried out. A special measurement system and dedicated software were developed to measure the power generated by the modules. The research object was a 1.3-l small diesel engine with power output of 66 kW. The tests were carried out on a dynamic engine test bed that allows reproduction of an actual driving cycle expressed as a function V = f( t), simulating drivetrain (clutch, transmission) operating characteristics, vehicle geometrical parameters, and driver behavior. Measurements of exhaust gas thermodynamic parameters (temperature, pressure, and mass flow) as well as the voltage and current generated by the thermoelectric modules were performed during tests of our own design. Based on the results obtained, the flow of exhaust gas energy in the entire exhaust system was determined along with the ATEG power output. The ideal area of the exhaust system for location of the ATEG was defined to ensure the highest thermal energy recovery efficiency.

  18. Technical Note: A numerical test-bed for detailed ice nucleation studies in the AIDA cloud simulation chamber

    Directory of Open Access Journals (Sweden)

    R. J. Cotton

    2007-01-01

    Full Text Available The AIDA (Aerosol Interactions and Dynamics in the Atmosphere aerosol and cloud chamber of Forschungszentrum Karlsruhe can be used to test the ice forming ability of aerosols. The AIDA chamber is extensively instrumented including pressure, temperature and humidity sensors, and optical particle counters. Expansion cooling using mechanical pumps leads to ice supersaturation conditions and possible ice formation. In order to describe the evolving chamber conditions during an expansion, a parcel model was modified to account for diabatic heat and moisture interactions with the chamber walls. Model results are shown for a series of expansions where the initial chamber temperature ranged from −20°C to −60°C and which used desert dust as ice forming nuclei. During each expansion, the initial formation of ice particles was clearly observed. For the colder expansions there were two clear ice nucleation episodes. In order to test the ability of the model to represent the changing chamber conditions and to give confidence in the observations of chamber temperature and humidity, and ice particle concentration and mean size, ice particles were simply added as a function of time so as to reproduce the observations of ice crystal concentration. The time interval and chamber conditions over which ice nucleation occurs is therefore accurately known, and enables the model to be used as a test bed for different representations of ice formation.

  19. Test and evaluation of load converter topologies used in the Space Station Freedom power management and distribution dc test bed

    Science.gov (United States)

    Lebron, Ramon C.; Oliver, Angela C.; Bodi, Robert F.

    1991-01-01

    Power components hardware in support of the Space Station freedom dc Electric Power System were tested. One type of breadboard hardware tested is the dc Load Converter Unit, which constitutes the power interface between the electric power system and the actual load. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. Three load converters were tested: a series resonant converter, a series inductor switch-mode converter, and a switching full-bridge forward converter. The topology, operation principles, and test results are described, in general. A comparative analysis of the three units is given with respect to efficiency, regulation, short circuit behavior (protection), and transient characteristics.

  20. Test and evaluation of load converter topologies used in the Space Station Freedom power management and distribution dc test bed

    Science.gov (United States)

    Lebron, Ramon C.; Oliver, Angela C.; Bodi, Robert F.

    1991-01-01

    Power components hardware in support of the Space Station freedom dc Electric Power System were tested. One type of breadboard hardware tested is the dc Load Converter Unit, which constitutes the power interface between the electric power system and the actual load. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. Three load converters were tested: a series resonant converter, a series inductor switch-mode converter, and a switching full-bridge forward converter. The topology, operation principles, and test results are described, in general. A comparative analysis of the three units is given with respect to efficiency, regulation, short circuit behavior (protection), and transient characteristics.

  1. Construction of an optical test-bed for eLISA

    Science.gov (United States)

    Lieser, Maike; Fitzsimons, E.; Isleif, K.-S.; Killow, C.; Perreur-Lloyd, M.; Robertson, D.; Schuster, S.; Tröbs, M.; Veith, S.; Ward, H.; Heinzel, G.; Danzmann, K.

    2016-05-01

    In the planned eLISA mission a key part of the system is the optical bench that holds the interferometers for reading out the inter-spacecraft distance and the test mass position. We report on ongoing technology development for the eLISA optical system like the back-link between the optical benches and the science interferometer where the local beam is interfered with the received beam from the distant spacecraft. The focus will be on a setup to investigate the tilt-to-pathlength coupling in the science interferometer. To test the science interferometer in the lab a second bench providing a laser beam and a reference interferometer is needed. We present a setup with two ultra-stable low expansion glass benches and bonded optics. To suppress the tilt-to-pathlength coupling to the required level (few μm/rad) imaging optics are placed in front of the interferometer photo diodes.

  2. Systems Engineering Management Plan NASA Traffic Aware Planner Integration Into P-180 Airborne Test-Bed

    Science.gov (United States)

    Maris, John

    2015-01-01

    NASA's Traffic Aware Planner (TAP) is a cockpit decision support tool that provides aircrew with vertical and lateral flight-path optimizations with the intent of achieving significant fuel and time savings, while automatically avoiding traffic, weather, and restricted airspace conflicts. A key step towards the maturation and deployment of TAP concerned its operational evaluation in a representative flight environment. This Systems Engineering Management Plan (SEMP) addresses the test-vehicle design, systems integration, and flight-test planning for the first TAP operational flight evaluations, which were successfully completed in November 2013. The trial outcomes are documented in the Traffic Aware Planner (TAP) flight evaluation paper presented at the 14th AIAA Aviation Technology, Integration, and Operations Conference, Atlanta, GA. (AIAA-2014-2166, Maris, J. M., Haynes, M. A., Wing, D. J., Burke, K. A., Henderson, J., & Woods, S. E., 2014).

  3. Numerical and Experimental Dynamic Analysis of IC Engine Test Beds Equipped with Highly Flexible Couplings

    Directory of Open Access Journals (Sweden)

    M. Cocconcelli

    2017-01-01

    Full Text Available Driveline components connected to internal combustion engines can be critically loaded by dynamic forces due to motion irregularity. In particular, flexible couplings used in engine test rig are usually subjected to high levels of torsional oscillations and time-varying torque. This could lead to premature failure of the test rig. In this work an effective methodology for the estimation of the dynamic behavior of highly flexible couplings in real operational conditions is presented in order to prevent unwanted halts. The methodology addresses a combination of numerical models and experimental measurements. In particular, two mathematical models of the engine test rig were developed: a torsional lumped-parameter model for the estimation of the torsional dynamic behavior in operative conditions and a finite element model for the estimation of the natural frequencies of the coupling. The experimental campaign addressed torsional vibration measurements in order to characterize the driveline dynamic behavior as well as validate the models. The measurements were achieved by a coder-based technique using optical sensors and zebra tapes. Eventually, the validated models were used to evaluate the effect of design modifications of the coupling elements in terms of natural frequencies (torsional and bending, torsional vibration amplitude, and power loss in the couplings.

  4. Second generation pressurized fluidized-bed combustion (PFBC) research and development, Phase 2 -- Task 4, carbonizer testing. Volume 1, Test results

    Energy Technology Data Exchange (ETDEWEB)

    Froehlich, R.; Robertson, A.; Vanhook, J.; Goyal, A.; Rehmat, A.; Newby, R.

    1994-11-01

    During the period beginning November 1991 and ending September 1992, a series of tests were conducted at Foster Wheeler Development Corporation in a fluidized-bed coal carbonizer to determine its performance characteristics. The carbonizer was operated for 533 hours in a jetting fluidized-bed configuration during which 36 set points (steady-state periods) were achieved. Extensive data were collected on the feed and product stream compositions, heating values, temperatures, and flow rates. With these data, elemental and energy balances were computed to evaluate and confirm accuracy of the data. The carbonizer data were not as self-consistent as could be desired (balance closure imperfection). A software package developed by Science Ventures, Inc., of California, called BALAID, was used to reconcile the carbonizer data; the details of the reconciliation have been given in Volume 1 of this report. The reconciled data for the carbonizer were rigorously analyzed, correlations were developed, and the model was updated accordingly. The model was then used in simulating each of the 36 steady-state periods achieved in the pilot plant. The details are given in this Volume of the report.

  5. Evaluation of power control concepts using the PMAD systems test bed. [Power Management and Distribution

    Science.gov (United States)

    Beach, R. F.; Kimnach, G. L.; Jett, T. A.; Trash, L. M.

    1989-01-01

    The Lewis Research Center's Power Management and Distribution (PMAD) System testbed and its use in the evaluation of control concepts applicable to the NASA Space Station Freedom electric power system (EPS) are described. The facility was constructed to allow testing of control hardware and software in an environment functionally similar to the space station electric power system. Control hardware and software have been developed to allow operation of the testbed power system in a manner similar to a supervisory control and data acquisition (SCADA) system employed by utility power systems for control. The system hardware and software are described.

  6. Edgewood Biosensors Test Bed Hand-held and Man-Portable Edition

    Science.gov (United States)

    2013-09-01

    and found the barcode scanner difficult to use. One commented, “This system is tedious”. Another concern for the soldiers in the field was the...assays at any given time. During the field testing, soldiers had difficulty manipulating the pouch and found the barcode scanner difficult to use. One...Manipulation of ticket reduced ease of use from Excellent to Good.   Difficulty using  barcode   scanner . Suggest a device on  barcode   scanner  for

  7. Demonstration and field trial of a resilient hybrid NG-PON test-bed

    Science.gov (United States)

    Prat, Josep; Polo, Victor; Schrenk, Bernhard; Lazaro, Jose A.; Bonada, Francesc; Lopez, Eduardo T.; Omella, Mireia; Saliou, Fabienne; Le, Quang T.; Chanclou, Philippe; Leino, Dmitri; Soila, Risto; Spirou, Spiros; Costa, Liliana; Teixeira, Antonio; Tosi-Beleffi, Giorgio M.; Klonidis, Dimitrios; Tomkos, Ioannis

    2014-10-01

    A multi-layer next generation PON prototype has been built and tested, to show the feasibility of extended hybrid DWDM/TDM-XGPON FTTH networks with resilient optically-integrated ring-trees architecture, supporting broadband multimedia services. It constitutes a transparent common platform for the coexistence of multiple operators sharing the optical infrastructure of the central metro ring, passively combining the access and the metropolitan network sections. It features 32 wavelength connections at 10 Gbps, up to 1000 users distributed in 16 independent resilient sub-PONs over 100 km. This paper summarizes the network operation, demonstration and field trial results.

  8. The Virtual Employment Test Bed: An Immersive Synthetic Environment Allows Engineers to Test and Evaluate Material Solutions

    Science.gov (United States)

    2014-04-03

    synthetic environment allows engineers to test and evaluate material solutions Robert DeMarco, MSBME; Gordon Cooke, MEME ; John Riedener, MSSE...ROBERT DEMARCO, MSBME, is a Project Lead Engineer and Certified LabVIEW Associate Developer. GORDON COOKE, MEME , is a Principal Investigator at the

  9. HIV incidence in rural South Africa: comparison of estimates from longitudinal surveillance and cross-sectional cBED assay testing.

    Directory of Open Access Journals (Sweden)

    Till Bärnighausen

    Full Text Available BACKGROUND: The BED IgG-Capture Enzyme Immunoassay (cBED assay, a test of recent HIV infection, has been used to estimate HIV incidence in cross-sectional HIV surveys. However, there has been concern that the assay overestimates HIV incidence to an unknown extent because it falsely classifies some individuals with non-recent HIV infections as recently infected. We used data from a longitudinal HIV surveillance in rural South Africa to measure the fraction of people with non-recent HIV infection who are falsely classified as recently HIV-infected by the cBED assay (the long-term false-positive ratio (FPR and compared cBED assay-based HIV incidence estimates to longitudinally measured HIV incidence. METHODOLOGY/PRINCIPAL FINDINGS: We measured the long-term FPR in individuals with two positive HIV tests (in the HIV surveillance, 2003-2006 more than 306 days apart (sample size n = 1,065. We implemented four different formulae to calculate HIV incidence using cBED assay testing (n = 11,755 and obtained confidence intervals (CIs by directly calculating the central 95(th percentile of incidence values. We observed 4,869 individuals over 7,685 person-years for longitudinal HIV incidence estimation. The long-term FPR was 0.0169 (95% CI 0.0100-0.0266. Using this FPR, the cross-sectional cBED-based HIV incidence estimates (per 100 people per year varied between 3.03 (95% CI 2.44-3.63 and 3.19 (95% CI 2.57-3.82, depending on the incidence formula. Using a long-term FPR of 0.0560 based on previous studies, HIV incidence estimates varied between 0.65 (95% CI 0.00-1.32 and 0.71 (95% CI 0.00-1.43. The longitudinally measured HIV incidence was 3.09 per 100 people per year (95% CI 2.69-3.52, after adjustment to the sex-age distribution of the sample used in cBED assay-based estimation. CONCLUSIONS/SIGNIFICANCE: In a rural community in South Africa with high HIV prevalence, the long-term FPR of the cBED assay is substantially lower than previous estimates. The cBED

  10. NASA Stennis Space Center Integrated System Health Management Test Bed and Development Capabilities

    Science.gov (United States)

    Figueroa, Fernando; Holland, Randy; Coote, David

    2006-01-01

    Integrated System Health Management (ISHM) is a capability that focuses on determining the condition (health) of every element in a complex System (detect anomalies, diagnose causes, prognosis of future anomalies), and provide data, information, and knowledge (DIaK)-not just data-to control systems for safe and effective operation. This capability is currently done by large teams of people, primarily from ground, but needs to be embedded on-board systems to a higher degree to enable NASA's new Exploration Mission (long term travel and stay in space), while increasing safety and decreasing life cycle costs of spacecraft (vehicles; platforms; bases or outposts; and ground test, launch, and processing operations). The topics related to this capability include: 1) ISHM Related News Articles; 2) ISHM Vision For Exploration; 3) Layers Representing How ISHM is Currently Performed; 4) ISHM Testbeds & Prototypes at NASA SSC; 5) ISHM Functional Capability Level (FCL); 6) ISHM Functional Capability Level (FCL) and Technology Readiness Level (TRL); 7) Core Elements: Capabilities Needed; 8) Core Elements; 9) Open Systems Architecture for Condition-Based Maintenance (OSA-CBM); 10) Core Elements: Architecture, taxonomy, and ontology (ATO) for DIaK management; 11) Core Elements: ATO for DIaK Management; 12) ISHM Architecture Physical Implementation; 13) Core Elements: Standards; 14) Systematic Implementation; 15) Sketch of Work Phasing; 16) Interrelationship Between Traditional Avionics Systems, Time Critical ISHM and Advanced ISHM; 17) Testbeds and On-Board ISHM; 18) Testbed Requirements: RETS AND ISS; 19) Sustainable Development and Validation Process; 20) Development of on-board ISHM; 21) Taxonomy/Ontology of Object Oriented Implementation; 22) ISHM Capability on the E1 Test Stand Hydraulic System; 23) Define Relationships to Embed Intelligence; 24) Intelligent Elements Physical and Virtual; 25) ISHM Testbeds and Prototypes at SSC Current Implementations; 26) Trailer

  11. The emission of Gamma Ray Bursts as a test-bed for modified gravity

    Energy Technology Data Exchange (ETDEWEB)

    Capozziello, S., E-mail: capozziello@na.infn.it [Dipartimento di Fisica, Universitá di Napoli “Federico II”, Via Cinthia, I-80126, Napoli (Italy); INFN Sez. di Napoli, Compl. Univ. di Monte S. Angelo, Edificio G, Via Cinthia, I-80126, Napoli (Italy); Gran Sasso Science Institute (INFN), Via F. Crispi 7, I-67100, L' Aquila (Italy); Lambiase, G. [Dipartimento di Fisica “E.R. Caianiello”, Universitá di Salerno, I-84084, Fisciano (Italy); INFN – Gruppo Collegato di Salerno (Italy)

    2015-11-12

    The extreme physical conditions of Gamma Ray Bursts can constitute a useful observational laboratory to test theories of gravity where very high curvature regimes are involved. Here we propose a sort of curvature engine capable, in principle, of explaining the huge energy emission of Gamma Ray Bursts. Specifically, we investigate the emission of radiation by charged particles non-minimally coupled to the gravitational background where higher order curvature invariants are present. The coupling gives rise to an additional force inducing a non-geodesic motion of particles. This fact allows a strong emission of radiation by gravitationally accelerated particles. As we will show with some specific model, the energy emission is of the same order of magnitude of that characterizing the Gamma Ray Burst physics. Alternatively, strong curvature regimes can be considered as a natural mechanism for the generation of highly energetic astrophysical events. Possible applications to cosmology are discussed.

  12. The emission of Gamma Ray Bursts as a test-bed for modified gravity

    Directory of Open Access Journals (Sweden)

    S. Capozziello

    2015-11-01

    Full Text Available The extreme physical conditions of Gamma Ray Bursts can constitute a useful observational laboratory to test theories of gravity where very high curvature regimes are involved. Here we propose a sort of curvature engine capable, in principle, of explaining the huge energy emission of Gamma Ray Bursts. Specifically, we investigate the emission of radiation by charged particles non-minimally coupled to the gravitational background where higher order curvature invariants are present. The coupling gives rise to an additional force inducing a non-geodesic motion of particles. This fact allows a strong emission of radiation by gravitationally accelerated particles. As we will show with some specific model, the energy emission is of the same order of magnitude of that characterizing the Gamma Ray Burst physics. Alternatively, strong curvature regimes can be considered as a natural mechanism for the generation of highly energetic astrophysical events. Possible applications to cosmology are discussed.

  13. Improving Ventilation and Saving Energy: Laboratory Study in aModular Classroom Test Bed

    Energy Technology Data Exchange (ETDEWEB)

    Apte, Michael G.; Buchanan, Ian S.; Faulkner, David; Fisk,William J.; Lai, Chi-Ming; Spears, Michael; Sullivan, Douglas P.

    2005-08-01

    supply throughout the study. Indoor CO2 levels with simulated occupancy were maintained below 1000 ppm. Finally temperature settings were met and controlled accurately. The goals of the laboratory testing phase were met and this system is ready for further study in a field test of occupied classrooms.

  14. Helicopter Field Testing of NASA's Autonomous Landing and Hazard Avoidance Technology (ALHAT) System fully Integrated with the Morpheus Vertical Test Bed Avionics

    Science.gov (United States)

    Epp, Chirold D.; Robertson, Edward A.; Ruthishauser, David K.

    2013-01-01

    The Autonomous Landing and Hazard Avoidance Technology (ALHAT) Project was chartered to develop and mature to a Technology Readiness Level (TRL) of six an autonomous system combining guidance, navigation and control with real-time terrain sensing and recognition functions for crewed, cargo, and robotic planetary landing vehicles. The ALHAT System must be capable of identifying and avoiding surface hazards to enable a safe and accurate landing to within tens of meters of designated and certified landing sites anywhere on a planetary surface under any lighting conditions. This is accomplished with the core sensing functions of the ALHAT system: Terrain Relative Navigation (TRN), Hazard Detection and Avoidance (HDA), and Hazard Relative Navigation (HRN). The NASA plan for the ALHAT technology is to perform the TRL6 closed loop demonstration on the Morpheus Vertical Test Bed (VTB). The first Morpheus vehicle was lost in August of 2012 during free-flight testing at Kennedy Space Center (KSC), so the decision was made to perform a helicopter test of the integrated ALHAT System with the Morpheus avionics over the ALHAT planetary hazard field at KSC. The KSC helicopter tests included flight profiles approximating planetary approaches, with the entire ALHAT system interfaced with all appropriate Morpheus subsystems and operated in real-time. During these helicopter flights, the ALHAT system imaged the simulated lunar terrain constructed in FY2012 to support ALHAT/Morpheus testing at KSC. To the best of our knowledge, this represents the highest fidelity testing of a system of this kind to date. During this helicopter testing, two new Morpheus landers were under construction at the Johnson Space Center to support the objective of an integrated ALHAT/Morpheus free-flight demonstration. This paper provides an overview of this helicopter flight test activity, including results and lessons learned, and also provides an overview of recent integrated testing of ALHAT on the second

  15. User attitudes in analyzing digital slides in a quality control test bed: a preliminary study.

    Science.gov (United States)

    Della Mea, Vincenzo; Demichelis, Francesca; Viel, Federico; Dalla Palma, Paolo; Beltrami, Carlo Alberto

    2006-05-01

    The pathologist examines suitably stained glass slides through a bright field microscope in order to render histopathological or cytological diagnosis by looking at tissues and cells. Glass slides serve as a permanent record of the patient disease. Over the course of a patient's treatment slides may need to be reviewed at other institutions before treatment can commence. Due to their fragile nature a transportable permanent digital facsimile of the glass slide would be ideal. A digital slide is a set of digital images representing the whole slide normally used by the pathologist, or a significant part of it; it is usually made by a large amount of images, up to thousands, which makes its management difficult. The present paper provides a description of the requirements needed to reproduce glass slides and of the available technological equipment, then the features of the two systems we implemented on different hardware are described, together with those of the digital slide viewer. The viewer was evaluated in two experimental test phases, during which user behaviour and diagnostic reports were measured. Digital slides used in the two experiments were acquired with either system. Possible applications of digital slides are then discussed, including undergraduate and professional education, quality control, and image analysis on full samples as well as on tissue microarrays.

  16. Design and Experiment of Electronic-hydraulic Loading Test-bed Based on Tractor’s Hydraulic Steering By-wire

    Institute of Scientific and Technical Information of China (English)

    Yue JIN; Yang LU; Jiahui GONG; Zhixiong LU; Wenming LI; Jungan WU

    2015-01-01

    An Electro-hydraulic loading system is designed based on a test-bed of tractor’s hydraulic steering by-wire. To simulate the steering resistance driving tractor in many kinds of soils and roads,the loading force is controlled to make proportional and continuous variable by an electro-hydraulic proportional relief valve. A steering resistance loading test-bed is built to test three kinds of steering resistance including constant,step and sine style. Tire lateral resistance is also tested under different steering conditions. The result shows that the electro-hydraulic loading system has high stability and following performance. Besides,the system’s steady state error is lower than 3. 1%,and it meets the test requirement of tractor’s hydraulic steering by-wire.

  17. Cold test with a benchtop set-up for fluidized bed reactor using quartz sand to simulate gasification of coal cokes by concentrated solar radiation

    Science.gov (United States)

    Gokon, Nobuyuki; Tanabe, Tomoaki; Shimizu, Tadaaki; Kodama, Tatsuya

    2016-05-01

    The impacts of internal circulation of a mixture of coal-coke particles and quartz sand on the fluidization state in a fluidized bed reactor are investigated by a cold test with a benchtop set-up in order to design 10-30 kWth scale prototype windowed fluidized-bed reactor. Firstly, a basic relationship between pressure loss of inlet gas and gas velocity was experimentally examined using quartz sand with different particle sizes by a small-scale quartz tube with a distributor at ambient pressure and temperature. Based on the results, an appropriate particle range of quartz sand and layer height/layer diameter ratio (L/D ratio) was determined for a design of the fluidized bed reactor. Secondly, a windowed reactor mock-up was designed and fabricated for solar coke gasification using quartz sand as a bed material. The pressure loss between the inlet and outlet gases was examined, and descending cokes and sand particles on the sidewall of the reactor was observed in the reactor mock-up. The moving velocity and distance of descending particles/sands from the top to bottom of fluidized bed were measured by the visual observation of the colored tracer particles on outside wall of the reactor.

  18. Testing the bed-blocking hypothesis: does higher supply of nursing and care homes reduce delayed hospital discharges?

    OpenAIRE

    James Gaughan; Hugh Gravelle; Luigi Siciliani

    2014-01-01

    Hospital bed blocking occurs when hospital patients are ready to be discharged to a nursing home but no place is available, so that hospital care acts as a more costly substitute for long-term care. We investigate the extent to which higher supply of nursing home beds or lower prices can reduce hospital bed blocking. We use new Local Authority level administrative data from England on hospital delayed discharges in 2010-13. The results suggest that delayed discharges do respond to the availab...

  19. Retrieval process development and enhancements: Hydraulic test bed integrated testing. Fiscal year 1995 technology development summary report

    Energy Technology Data Exchange (ETDEWEB)

    Hatchell, B.K.; Smalley, J.T.; Tucker, J.C.

    1996-02-01

    The Retrieval Process Development and Enhancements Program is sponsored by the U.S. Department of Energy (DOE) Office of Science and Technology to investigate waste dislodging and conveyance processes suitable for the retrieval of high-level radioactive waste. This program, represented by industry, national laboratories, and academia, is testing the performance of a technology of high-pressure waterjet dislodging and pneumatic conveyance integrated as a scarifier as a means of retrieval of waste inside waste storage tanks. Waste stimulants have been designed to challenge this retrieval process, and this technology has been shown to mobilize and convey the waste stimulants, at target retrieval rates while operating within the space envelope and the dynamic loading constraints of postulated deployment systems. The approach has been demonstrated to be versatile in dislodging and conveying a broad range of waste forms, from hard wastes to soft sludge wastes, through the use of simple and reliable in-tank components.

  20. Real-Time Signal Processing for Multiantenna Systems: Algorithms, Optimization, and Implementation on an Experimental Test-Bed

    Directory of Open Access Journals (Sweden)

    Haustein Thomas

    2006-01-01

    Full Text Available A recently realized concept of a reconfigurable hardware test-bed suitable for real-time mobile communication with multiple antennas is presented in this paper. We discuss the reasons and prerequisites for real-time capable MIMO transmission systems which may allow channel adaptive transmission to increase link stability and data throughput. We describe a concept of an efficient implementation of MIMO signal processing using FPGAs and DSPs. We focus on some basic linear and nonlinear MIMO detection and precoding algorithms and their optimization for a DSP target, and a few principal steps for computational performance enhancement are outlined. An experimental verification of several real-time MIMO transmission schemes at high data rates in a typical office scenario is presented and results on the achieved BER and throughput performance are given. The different transmission schemes used either channel state information at both sides of the link or at one side only (transmitter or receiver. Spectral efficiencies of more than 20 bits/s/Hz and a throughput of more than 150 Mbps were shown with a single-carrier transmission. The experimental results clearly show the feasibility of real-time high data rate MIMO techniques with state-of-the-art hardware and that more sophisticated baseband signal processing will be an essential part of future communication systems. A discussion on implementation challenges towards future wireless communication systems supporting higher data rates (1 Gbps and beyond or high mobility concludes the paper.

  1. Self-Pressurization and Spray Cooling Simulations of the Multipurpose Hydrogen Test Bed (MHTB) Ground-Based Experiment

    Science.gov (United States)

    Kartuzova, O.; Kassemi, M.; Agui, J.; Moder, J.

    2014-01-01

    This paper presents a CFD (computational fluid dynamics) model for simulating the self-pressurization of a large scale liquid hydrogen storage tank. In this model, the kinetics-based Schrage equation is used to account for the evaporative and condensing interfacial mass flows. Laminar and turbulent approaches to modeling natural convection in the tank and heat and mass transfer at the interface are compared. The flow, temperature, and interfacial mass fluxes predicted by these two approaches during tank self-pressurization are compared against each other. The ullage pressure and vapor temperature evolutions are also compared against experimental data obtained from the MHTB (Multipuprpose Hydrogen Test Bed) self-pressurization experiment. A CFD model for cooling cryogenic storage tanks by spraying cold liquid in the ullage is also presented. The Euler- Lagrange approach is utilized for tracking the spray droplets and for modeling interaction between the droplets and the continuous phase (ullage). The spray model is coupled with the VOF (volume of fluid) model by performing particle tracking in the ullage, removing particles from the ullage when they reach the interface, and then adding their contributions to the liquid. Droplet ullage heat and mass transfer are modeled. The flow, temperature, and interfacial mass flux predicted by the model are presented. The ullage pressure is compared with experimental data obtained from the MHTB spray bar mixing experiment. The results of the models with only droplet/ullage heat transfer and with heat and mass transfer between the droplets and ullage are compared.

  2. Developing a test-bed for robust research governance of geoengineering: the contribution of ocean iron biogeochemistry

    Science.gov (United States)

    Boyd, Philip W.; Bressac, Matthieu

    2016-11-01

    Geoengineering to mitigate climate change has long been proposed, but remains nebulous. Exploration of the feasibility of geoengineering first requires the development of research governance to move beyond the conceptual towards scientifically designed pilot studies. Fortuitously, 12 mesoscale (approx. 1000 km2) iron enrichments, funded to investigate how ocean iron biogeochemistry altered Earth's carbon cycle in the geological past, provide proxies to better understand the benefits and drawbacks of geoengineering. The utility of these iron enrichments in the geoengineering debate is enhanced by the GEOTRACES global survey. Here, we outline how GEOTRACES surveys and process studies can provide invaluable insights into geoengineering. Surveys inform key unknowns including the regional influence and magnitude of modes of iron supply, and stimulate iron biogeochemical modelling. These advances will enable quantification of interannual variability of iron supply to assess whether any future purposeful multi-year iron-fertilization meets the principle of `additionality' (sensu Kyoto protocol). Process studies address issues including upscaling of geoengineering, and how differing iron-enrichment strategies could stimulate wide-ranging biogeochemical outcomes. In summary, the availability of databases on both mesoscale iron-enrichment studies and the GEOTRACES survey, along with modelling, policy initiatives and legislation have positioned the iron-enrichment approach as a robust multifaceted test-bed to assess proposed research into climate intervention. This article is part of the themed issue 'Biological and climatic impacts of ocean trace element chemistry'.

  3. Secondary Waste Form Screening Test Results—THOR® Fluidized Bed Steam Reforming Product in a Geopolymer Matrix

    Energy Technology Data Exchange (ETDEWEB)

    Pires, Richard P.; Westsik, Joseph H.; Serne, R. Jeffrey; Mattigod, Shas V.; Golovich, Elizabeth C.; Valenta, Michelle M.; Parker, Kent E.

    2011-07-14

    Screening tests are being conducted to evaluate waste forms for immobilizing secondary liquid wastes from the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Plans are underway to add a stabilization treatment unit to the Effluent Treatment Facility to provide the needed capacity for treating these wastes from WTP. The current baseline is to use a Cast Stone cementitious waste form to solidify the wastes. Through a literature survey, DuraLith alkali-aluminosilicate geopolymer, fluidized-bed steam reformation (FBSR) granular product encapsulated in a geopolymer matrix, and a Ceramicrete phosphate-bonded ceramic were identified both as candidate waste forms and alternatives to the baseline. These waste forms have been shown to meet waste disposal acceptance criteria, including compressive strength and universal treatment standards for Resource Conservation and Recovery Act (RCRA) metals (as measured by the toxicity characteristic leaching procedure [TCLP]). Thus, these non-cementitious waste forms should also be acceptable for land disposal. Information is needed on all four waste forms with respect to their capability to minimize the release of technetium. Technetium is a radionuclide predicted to be in the secondary liquid wastes in small quantities, but the Integrated Disposal Facility (IDF) risk assessment analyses show that technetium, even at low mass, produces the largest contribution to the estimated IDF disposal impacts to groundwater.

  4. Integrated Test Bed Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The ITB's avionics system is composed of multiple high performance processors, embedded software, and data communication systems. The avionics embedded software is a...

  5. 基于VB.NET的无线电设备综合测试平台%Synthesis test bed for radio device based on VB.NET

    Institute of Scientific and Technical Information of China (English)

    王秀敏; 张燕; 毛兴鹏

    2012-01-01

    无线电设备的测试需要较多的专业知识,而且步骤繁琐.为简化无线电设备的测试过程和缩短测试时间,以VB.NET为基础研究了一种无线电设备综合测试平台.该平台能够自动控制各种无线电通信设备,实现各种参数的自动测量和处理,并自动完成数据的记录及报表的生成.使用该平台可以极大地简化人工操作的复杂度、缩短测量时间并进一步提高测试结果的准确性和权威性.%Professional knowledge is a precondition for testing radio devices and the process is so complicated. To simplify the process and shorten the time, a synthesis test bed for radio device is designed based on VB . NET. Utilizing the proposed test bed, all apparatus needed for test are connected, and every parameter is measured and processed automatically, before data recording and reports building. By utilizing the test bed proposed, the complexity of operating is simplified, the measure time is shortea The veracity and the authority of the test result is improved further.

  6. Unique Nanoparticle Properties Confound Fluorescent Based Assays Widely Employed in Their In Vitro Toxicity Testing and Ranking

    Science.gov (United States)

    Nanomaterials are a diverse collection of novel materials that exhibit at least one dimension less than 100 nm and display unique chemical and physical properties due to their nanoscale size. An emphasis has been put on developing high throughput screening (HTS) assays to charac...

  7. Effect of Climatic Conditions on Differences in Thermo-Technical Properties of Organic Bedding in Laboratory Testing

    Directory of Open Access Journals (Sweden)

    Lendelová Jana

    2017-03-01

    Full Text Available The aim of this experiment was to analyse the influence of climatic factors on the thermal performance of separated liquid manure. The samples of organic bedding were collected from the lying area of dairy housing and preparatory store. The measurement of properties of recycled manure solids (RMS was carried out in laboratory conditions. Samples were examined with determining the temperature effect on the thermal conductivity λ of ’dry‘ separated liquid manure (with a dry matter content of 60% and ’wet‘ liquid manure (with a dry matter content of 26%, in air temperatures ranging from 0 °C to 40 °C. Subsequently, the thermal resistance of three selected types of cows lying structures was calculated for winter and summer boundary values. Based on the results of thermal conductivity and thermal resistance, it was observed that dry separated liquid manure as an alternative bedding has, in low temperature (up to 5 °C, the most suitable thermal performance if it is maintained in a dry condition (with a dry matter content of 60%. With increasing temperature (above 20 °C and increasing humidity of bedding (below 26%, thermo-technical properties get worse; however, when comparing the thermal resistance of the cow bed structure with sandwich mattresses with a 50 mm layer of organic bedding and the deep cubicle filled with 200 mm of organic bedding, the thermal resistance of floor structure decreases by 7.6% or 18.4%, respectively. With a proper handling of the recycled organic bedding, it is possible to use its economic advantages.

  8. MINERALIZATION OF RADIOACTIVE WASTES BY FLUIDIZED BED STEAM REFORMING (FBSR): COMPARISONS TO VITREOUS WASTE FORMS, AND PERTINENT DURABILITY TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2008-12-26

    The Savannah River National Laboratory (SRNL) was requested to generate a document for the Washington State Department of Ecology and the U.S. Environmental Protection Agency that would cover the following topics: (1) A description of the mineral structures produced by Fluidized Bed Steam Reforming (FBSR) of Hanford type Low Activity Waste (LAW including LAWR which is LAW melter recycle waste) waste, especially the cage structured minerals and how they are formed. (2) How the cage structured minerals contain some contaminants, while others become part of the mineral structure (Note that all contaminants become part of the mineral structure and this will be described in the subsequent sections of this report). (3) Possible contaminant release mechanisms from the mineral structures. (4) Appropriate analyses to evaluate these release mechanisms. (5) Why the appropriate analyses are comparable to the existing Hanford glass dataset. In order to discuss the mineral structures and how they bond contaminants a brief description of the structures of both mineral (ceramic) and vitreous waste forms will be given to show their similarities. By demonstrating the similarities of mineral and vitreous waste forms on atomic level, the contaminant release mechanisms of the crystalline (mineral) and amorphous (glass) waste forms can be compared. This will then logically lead to the discussion of why many of the analyses used to evaluate vitreous waste forms and glass-ceramics (also known as glass composite materials) are appropriate for determining the release mechanisms of LAW/LAWR mineral waste forms and how the durability data on LAW/LAWR mineral waste forms relate to the durability data for LAW/LAWR glasses. The text will discuss the LAW mineral waste form made by FBSR. The nanoscale mechanism by which the minerals form will be also be described in the text. The appropriate analyses to evaluate contaminant release mechanisms will be discussed, as will the FBSR test results to

  9. International Space Station Sustaining Engineering: A Ground-Based Test Bed for Evaluating Integrated Environmental Control and Life Support System and Internal Thermal Control System Flight Performance

    Science.gov (United States)

    Ray, Charles D.; Perry, Jay L.; Callahan, David M.

    2000-01-01

    As the International Space Station's (ISS) various habitable modules are placed in service on orbit, the need to provide for sustaining engineering becomes increasingly important to ensure the proper function of critical onboard systems. Chief among these are the Environmental Control and Life Support System (ECLSS) and the Internal Thermal Control System (ITCS). Without either, life onboard the ISS would prove difficult or nearly impossible. For this reason, a ground-based ECLSS/ITCS hardware performance simulation capability has been developed at NASA's Marshall Space Flight Center. The ECLSS/ITCS Sustaining Engineering Test Bed will be used to assist the ISS Program in resolving hardware anomalies and performing periodic performance assessments. The ISS flight configuration being simulated by the test bed is described as well as ongoing activities related to its preparation for supporting ISS Mission 5A. Growth options for the test facility are presented whereby the current facility may be upgraded to enhance its capability for supporting future station operation well beyond Mission 5A. Test bed capabilities for demonstrating technology improvements of ECLSS hardware are also described.

  10. IDENTIFICATION OF APPROPRIATE QUALIFICATION TESTING AND END-OF-LIFE WASTE STORAGE CONSIDERATIONS FOR DEEP BED SAND FILTERS

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, K.

    2010-06-02

    Deep bed sand (DBS) filters have filtered radioactive particulates at two United States Department of Energy (DOE) sites since 1948. Some early DBS filters experienced issues with chemical attack on support tiles, requiring significant repairs. Designs of DBS filters constructed since 1970 paid greater attention to chemical compatibility, resulting in decades of reliable performance since 1975.

  11. Design of Pneumatic Device of the Automatic Transmission Performance Test-bed%气动自动变速器试验台架的设计

    Institute of Scientific and Technical Information of China (English)

    王利利

    2012-01-01

    根据自动变速器的工作原理特性,结合自动变速器的专业教学实践,分析了目前大多数变速器解剖试验台架的缺点,设计了以气压为动力传动介质的自动变速器解剖运行试验台.气动自动变速器实物解剖试验台架能实现动态演示,突破了教学上的难点,提高了学生的学习兴趣,取得了较好的试验教学效果.%According to the work principle of automatic transmission,combined with the experimental teaching of automatic transmission, the current most transmission test-bed shortcomings were analyzed. An automat transmission test-bed introducing of pneumatic device was designed. The test-bed can realize the dynamic demonstration and break through the teaching difficulty, which enables students to improve the study interest, and get better effects of teaching.

  12. Pressurized fluidized-bed hydroretorting of Eastern oil shales -- Sulfur control. Topical report for Subtask 3.1, In-bed sulfur capture tests; Subtask 3.2, Electrostatic desulfurization; Subtask 3.3, Microbial desulfurization and denitrification

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, M.J.; Abbasian, J.; Akin, C.; Lau, F.S.; Maka, A.; Mensinger, M.C.; Punwani, D.V.; Rue, D.M. [Institute of Gas Technology, Chicago, IL (United States); Gidaspow, D.; Gupta, R.; Wasan, D.T. [Illinois Inst. of Tech., Chicago, IL (United States); Pfister, R.M.: Krieger, E.J. [Ohio State Univ., Columbus, OH (United States)

    1992-05-01

    This topical report on ``Sulfur Control`` presents the results of work conducted by the Institute of Gas Technology (IGT), the Illinois Institute of Technology (IIT), and the Ohio State University (OSU) to develop three novel approaches for desulfurization that have shown good potential with coal and could be cost-effective for oil shales. These are (1) In-Bed Sulfur Capture using different sorbents (IGT), (2) Electrostatic Desulfurization (IIT), and (3) Microbial Desulfurization and Denitrification (OSU and IGT). The objective of the task on In-Bed Sulfur Capture was to determine the effectiveness of different sorbents (that is, limestone, calcined limestone, dolomite, and siderite) for capturing sulfur (as H{sub 2}S) in the reactor during hydroretorting. The objective of the task on Electrostatic Desulfurization was to determine the operating conditions necessary to achieve a high degree of sulfur removal and kerogen recovery in IIT`s electrostatic separator. The objectives of the task on Microbial Desulfurization and Denitrification were to (1) isolate microbial cultures and evaluate their ability to desulfurize and denitrify shale, (2) conduct laboratory-scale batch and continuous tests to improve and enhance microbial removal of these components, and (3) determine the effects of processing parameters, such as shale slurry concentration, solids settling characteristics, agitation rate, and pH on the process.

  13. The Ratio of Retrograde to Prograde Orbits: A Unique Way to test Kuiper Belt Binary Formation Theories

    CERN Document Server

    Schlichting, Hilke E

    2008-01-01

    With the discovery of Kuiper Belt binaries that have wide separations and roughly equal masses new theories were proposed to explain their formation. Two formation scenarios were suggested by Goldreich and collaborators: In the first, dynamical friction that is generated by the sea of small bodies enables a transient binary to become bound ($L^2s$ mechanism); in the second, a transient binary gets bound by an encounter with a third body ($L^3$ mechanism). We show that these different binary formation scenarios leave their own unique signatures in the relative abundance of prograde to retrograde binary orbits. This signature is due to stable retrograde orbits that exist much further out in the Hill sphere than prograde orbits. It provides an excellent opportunity to distinguish between the different binary formation scenarios observationally. We predict that if binary formation proceeded while sub-Hill velocities prevailed, the vast majority of all comparable mass ratio binaries have retrograde orbits. This do...

  14. Experimental investigations of flow distribution in coolant system of Helium-Cooled-Pebble-Bed Test Blanket Module

    Energy Technology Data Exchange (ETDEWEB)

    Ilić, M.; Schlindwein, G., E-mail: georg.schlindwein@kit.edu; Meyder, R.; Kuhn, T.; Albrecht, O.; Zinn, K.

    2016-02-15

    Highlights: • Experimental investigations of flow distribution in HCPB TBM are presented. • Flow rates in channels close to the first wall are lower than nominal ones. • Flow distribution in central chambers of manifold 2 is close to the nominal one. • Flow distribution in the whole manifold 3 agrees well with the nominal one. - Abstract: This paper deals with investigations of flow distribution in the coolant system of the Helium-Cooled-Pebble-Bed Test Blanket Module (HCPB TBM) for ITER. The investigations have been performed by manufacturing and testing of an experimental facility named GRICAMAN. The facility involves the upper poloidal half of HCPB TBM bounded at outlets of the first wall channels, at outlet of by-pass pipe and at outlets of cooling channels in breeding units. In this way, the focus is placed on the flow distribution in two mid manifolds of the 4-manifold system: (i) manifold 2 to which outlets of the first wall channels and inlet of by-pass pipe are attached and (ii) manifold 3 which supplies channels in breeding units with helium coolant. These two manifolds are connected with cooling channels in vertical/horizontal grids and caps. The experimental facility has been built keeping the internal structure of manifold 2 and manifold 3 exactly as designed in HCPB TBM. The cooling channels in stiffening grids, caps and breeding units are substituted by so-called equivalent channels which provide the same hydraulic resistance and inlet/outlet conditions, but have significantly simpler geometry than the real channels. Using the conditions of flow similarity, the air pressurized at 0.3 MPa and at ambient temperature has been used as working fluid instead of HCPB TBM helium coolant at 8 MPa and an average temperature of 370 °C. The flow distribution has been determined by flow rate measurements at each of 28 equivalent channels, while the pressure distribution has been obtained measuring differential pressure at more than 250 positions. The

  15. High temperature degradation by erosion-corrosion in bubbling fluidized bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Peggy Y.; MacAdam, S.; Niu, Y.; Stringer, J.

    2003-04-22

    Heat-exchanger tubes in fluidized bed combustors (FBCs) often suffer material loss due to combined corrosion and erosion. Most severe damage is believed to be caused by the impact of dense packets of bed material on the lower parts of the tubes. In order to understand this phenomenon, a unique laboratory test rig at Berkeley was designed to simulate the particle hammering interactions between in-bed particles and tubes in bubbling fluidized bed combustors. In this design, a rod shaped specimen is actuated a short distance within a partially fluidized bed. The downward specimen motion is controlled to produce similar frequencies, velocities and impact forces as those experienced by the impacting particle aggregates in practical systems. Room temperature studies have shown that the degradation mechanism is a three-body abrasion process. This paper describes the characteristics of this test rig, reviews results at elevated temperatures and compares them to field experience. At higher temperatures, deposits of the bed material on tube surfaces can act as a protective layer. The deposition depended strongly on the type of bed material, the degree of tube surface oxidation and the tube and bed temperatures. With HCl present in the bed, wastage was increased due to enhanced oxidation and reduced oxide scale adherence.

  16. Impact of air traffic emissions on airport air quality. Multi-scale modeling, test bed and field measurements

    Science.gov (United States)

    Ramaroson, R.; Vuillot, F.; Durand, Y.; Courbet, B.; Janin, F.; Copalle, A.; Guin, C.; Paux, E.; Vannier, F.; Talbaut, M.; Weill, M.

    2004-12-01

    engines. Evidence of NOx regime is simulated for the ozone formation at and surrounding airports. At the boarding area, during aircraft parking, APU are generally operated for supplementary electrical power supply for cabin cooling or heating. APU emission indices of NOx, CO, HC and PM equipping civil aircraft are still badly known as they are not certified. Emission indices of soot, NOx, CO, CO2, have been measured on test bed for a specific APU consuming kerosene. Results show that APU emissions are comparable to aero-engine indices for gas, but are far more important for soot. Consequently it is expected that APU emissions are potentially important at airports. Finally, real-time continuous measurements of airborne PM, size distribution and number concentration, have been performed at Nice airport-France, along taxiways for 3 days, in summer 2003 using a 13-stage ELPI. Results show that, when road traffic emissions are not transported into the airport, the observed PM concentration does not exceed the French national threshold for PM mass in summer 2003.

  17. Laboratory Testing of a Fluidized-Bed Dry-Scrubbing Process for the Removal of Acidic Gases from a Simulated Incinerator Flue Gas

    Science.gov (United States)

    1989-04-01

    Vertical Pneu- matic Transport Reactor ," Ind. Eng. Chem. Process Des. Dev., 23(3), 539-45 (1984). 3. R. Graf and J. D. Riley, "Dry/Semi-Dry Flue Cas...Kuni and Levenspiel ) W0 Gildart clo,,itiat ion" Group ItI l rotI ed r desc r i bed in ASTM St arda rd C 110-87. 22 REFERENCES 1. W. M. Bradshaw...Cement; Lime; Gyp- sum, American Society for Testing and Materials, Philadelphia, Pennsylvania, 1988. 3. D. Kuni and 0. Levenspiel , Fluidization

  18. Development of NASA's Space Communications and Navigation Test Bed Aboard ISS to Investigate SDR, On-Board Networking and Navigation Technologies

    Science.gov (United States)

    Reinhart, Richard C.; Kacpura, Thomas J.; Johnson, Sandra K.; Lux, James P.

    2010-01-01

    NASA is developing an experimental flight payload (referred to as the Space Communication and Navigation (SCAN) Test Bed) to investigate software defined radio (SDR), networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASA s Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developments underway by NASA and industry partners. Planned for launch in early 2012, the payload will be externally mounted to the International Space Station truss and conduct experiments representative of future mission capability.

  19. Wind power integration in island-based smart grid projects : A comparative study between Jeju Smart Grid Test-bed and Smart Grid Gotland

    OpenAIRE

    Piehl, Hampus

    2014-01-01

    Smart grids seem to be the solution to use energy from renewable and intermittent energy sources in an efficient manner. There are many research projects around the world and two of them are Jeju Smart Grid Test-bed and Smart Grid Gotland. They have in common that they are both island-based projects and connected to the Powergrid on the mainland by HVDC-link. The purpose of this thesis is to compare the two projects and find out what challenges and strategies they have related to wind power i...

  20. AMT试验台控制系统的研发%Research on Automatic Control System Used in Test Bed for AMT Transmission

    Institute of Scientific and Technical Information of China (English)

    武州; 石晓辉; 李文礼

    2012-01-01

    The control system of AMT transmission reliability testing was designed. After displaying the measurement principle of the temperature, rotational speed, torque, the measurement and control of them are explained. A control system of test bed for AMT transmission takes the industry control computer as the core is introduced. It is based on virtual instrumentation software of Lab Windows/CVI with friendly user interface. Control system can set parameter of testing to test several types of AMT gearbox on same test - bed. It also can make test loading stable by using AC variable frequency motor, automatic-control and breakdown warning in the process of test. This control system guarantee whole of steady operation to test -bed, having good security and stability.%对AMT变速器进行可靠性测试,设计了汽车AMT变速器试验台的控制系统;开发了一套汽车变速器可靠性试验台控制系统的硬件及软件结构,说明了温度、转速、转矩的测量原理以及对它们的测量和控制;该控制系统以工业控制计算机为核心,以虚拟仪器设计软件Lab Windows/CVI为开发平台,可根据试验参数的设置利用同一试验台进行多种型号AMT变速器的试验,利用交流变频电机实现试验转矩的平稳加载,能够实现试验过程的自动控制和故障报警;该控制系统确保了整个试验台的稳定运行,具有良好的安全性和稳定性.

  1. Impact of different discharge patterns on bed occupancy rate and bed waiting time: a simulation approach.

    Science.gov (United States)

    Zhu, Zhecheng

    2011-01-01

    Beds are one of the most important resources in a healthcare system. How to manage beds efficiently is an important indicator of the efficiency of the healthcare system. Bed management is challenging to many healthcare service providers in many aspects. In recent years, population growth and aging society impose extra pressure on bed requirement. There are usually two key performance indicators of a bed management system: bed occupancy rate and bed waiting time. In this paper, different discharge patterns and their impacts on the bed occupancy rate and bed waiting time are studied. A discrete event simulation model is constructed to evaluate the existing discharge pattern in a Singapore regional hospital using actual hospital admission and discharge transaction data. Then different discharge patterns are tested in the same context. Simulation results show that a proper discharge pattern significantly smoothes the fluctuation of bed occupancy rate and reduce the bed waiting time.

  2. Solar Variability and the Near-Earth Environment: Mining Enhanced Low Dose Rate Sensitivity Data From the Microelectronics and Photonics Test Bed Space Experiment

    Science.gov (United States)

    Turflinger, T.; Schmeichel, W.; Krieg, J.; Titus, J.; Campbell, A.; Reeves, M.; Marshall (P.); Hardage, Donna (Technical Monitor)

    2004-01-01

    This effort is a detailed analysis of existing microelectronics and photonics test bed satellite data from one experiment, the bipolar test board, looking to improve our understanding of the enhanced low dose rate sensitivity (ELDRS) phenomenon. Over the past several years, extensive total dose irradiations of bipolar devices have demonstrated that many of these devices exhibited ELDRS. In sensitive bipolar transistors, ELDRS produced enhanced degradation of base current, resulting in enhanced gain degradation at dose rates 1 rd(Si)/s. This Technical Publication provides updated information about the test devices, the in-flight experiment, and both flight-and ground-based observations. Flight data are presented for the past 5 yr of the mission. These data are compared to ground-based data taken on devices from the same date code lots. Information about temperature fluctuations, power shutdowns, and other variables encountered during the space flight are documented.

  3. Racing for the Bed

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    No one knows when the people ofMacheng City began to employthe marriage custom of racingfor the bed, once a custom unique to theTujia ethnic minority. It is said that at the end of awedding, bride and bridegroom enter thebridal chamber together and race for thebed. The one who is the first to sit on thebed will be the master of the new familyIt sounds unreasonable, but quite anumber of people believe in it.Therefore, on the wedding night, manybrides and bridegrooms try their best to

  4. Research and development of a phosphoric acid fuel cell/battery power source integrated in a test-bed bus. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-30

    This project, the research and development of a phosphoric acid fuel cell/battery power source integrated into test-bed buses, began as a multi-phase U.S. Department of Energy (DOE) project in 1989. Phase I had a goal of developing two competing half-scale (25 kW) brassboard phosphoric acid fuel cell systems. An air-cooled and a liquid-cooled fuel cell system were developed and tested to verify the concept of using a fuel cell and a battery in a hybrid configuration wherein the fuel cell supplies the average power required for operating the vehicle and a battery supplies the `surge` or excess power required for acceleration and hill-climbing. Work done in Phase I determined that the liquid-cooled system offered higher efficiency.

  5. Testing fluidized bed incinerators for energy-efficient operation for the Southtowns Sewage Treatment Agency. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    Two methods for improving the energy efficiency of fluidized bed sludge incinerators were evaluated. The first method used paper pulp and polymer as conditioning agents for municipal sludge instead of lime and ferric chloride. Automatic control of the incinerator was the second method evaluated for energy savings. To evaluate the use of paper pulp and polymer as conditioning agents, varying quantities of paper pulp were added to the liquid sludge to determine the optimal sludge-to-paper pulp ratio. The effect of the paper pulp and polymer-conditioned sludge on plant operations also was evaluated. When compared to sludge conditioned with lime and ferric chloride, the paper pulp and polymer-conditioned sludge had similar cake release and feed characteristics, higher BTU values for the dry sludge solids, required less auxiliary fuel for incineration, and generated less ash for disposal. The paper pulp and polymer did not have any appreciable negative effects on the operation of the wastewater treatment plant. It was estimated that processing and incinerating the sludge conditioned with paper pulp and polymer resulted in a cost savings of up to $91.73 per dry ton of activated sludge solids. To evaluate the effect of automatic control, all the incinerator operating parameters including air flow rates, fuel oil feed rates, and sludge feed rates, were automatically monitored and controlled to minimize auxiliary fuel oil use and to keep the incinerator running at optimal conditions. Although effective, the estimated cost savings for automatic control of the incinerator were small.

  6. Detecting glacier-bed overdeepenings for glaciers in the Western Italian Alps using the GlabTop2 model: the test site of the Rutor Glacier, Aosta Valley

    Science.gov (United States)

    Viani, Cristina; Machguth, Horst; Huggel, Christian; Perotti, Luigi; Giardino, Marco

    2016-04-01

    It is expected that the rapid retreat of glaciers, observed in the European Alps and other mountain regions of the world, will continue in the future. One of the most evident and relevant consequences of this phenomenon is the formation of new glacier lakes in recently deglaciated areas. During glacier retreat overdeepened parts of the glacier bed become exposed and, in some cases, filled with water. It is important to understand where these new lakes can appear because of the associated potential risks (i.e. lake outburst and consequent flood) and opportunities (tourism, hydroelectricity, water reservoir, etc.) especially in densely populated areas such as the European Alps. GlabTop2 (Glacier Bed Topography model version 2) allows to model glacier bed topography over large glaciated areas combining digital terrain information and slope-related estimates of glacier thickness. The model requires a minimum set of input data: glaciers outlines and a surface digital elevation model (DEM). In this work we tested the model on the Rutor Glacier (8,1 km2) located in the Aosta Valley. The glacier has a well-known history of a series of glacier lake outburst floods between 1430 AD and 1864 AD due to front fluctuations. After the last advance occurred during the 70s of the previous century, glacier shrinkage has been continuous and new lakes have formed in newly exposed overdeepenings. We applied GlabTop2 to DEMs derived from historical data (topographic maps and aerial photos pair) representing conditions before the proglacial lake formation. The results obtained have been compared with the present situation and existing lakes. Successively we used the model also on present-day DEMs, which are of higher resolution than the historical derived ones, and compared the modeled bed topography with an existing bedrock map obtained by in-situ geophysical investigations (GPR surveys). Preliminary results, obtained with the 1991 surface model, confirm the robustness of GlabTop2 in

  7. Teste de susceptibilidade do percevejo, Cimex lectularius L. (Hemiptera, Cimicidae ao DDT em Belo Horizonte, MG (Brasil Susceptibility tests of the bed-bug Cimex lectularius L. (Hemiptera, Cimicidae to DDT in Belo Horizonte, MG (Brazil

    Directory of Open Access Journals (Sweden)

    Ronaldo L. Nagem

    1992-04-01

    Full Text Available O nível de susceptibilidade de percevejos adultos, Cimex lectularius, ao DDT, em Belo Horizonte, Minas Gerais (Brasil, foi determinado durante o período de 1985 a 1986. Os resultados indicaram, para os insetos testados, que uma dose de 4,0% do inseticida não foi suficiente para matar 55% dos insetos. Os dados permitem concluir que existem colonias de percevejos resistentes ao DDT em Belo Horizonte.Susceptibility levels for the adult bed-bug, Cimex lectularius, in Belo Horizonte, Minas Gerais - Brazil, to DDT, were determined during the period 1985 to 1986. The test results showed that a 4% dosage of DDT is not enough to kill 55% of the insects. The data are sufficient to show that there exists bed-bug resistance to DDT in Belo Horizonte.

  8. Second generation pressurized fluidized-bed combustion (PFBC) research and development, Phase 2 --- Task 4, carbonizer testing. Volume 2, Data reconciliation

    Energy Technology Data Exchange (ETDEWEB)

    Froehlich, R.; Robertson, A.; Vanhook, J.; Goyal, A.; Rehmat, A.; Newby, R.

    1994-11-01

    During the period beginning November 1991 and ending September 1992, a series of tests were conducted at Foster Wheeler Development Corporation in a fluidized-bed coal carbonizer to determine its performance characteristics. The carbonizer was operated for 533 hours in a jetting fluidized-bed configuration during which 36 set points (steady-state periods) were achieved. Extensive data were collected on the feed and product stream compositions, heating values, temperatures, and flow rates. With these data, elemental and energy balances were computed to evaluate and confirm accuracy of the data. The carbonizer data were not as self-consistent as could be desired (balance closure imperfection). A software package developed by Science Ventures, Inc., of California, called BALAID, was used to reconcile the carbonizer data; the details of the reconciliation have been given in Volume 1 of this report. The reconciled data for the carbonizer were rigorously analyzed, correlations were developed, and the model was updated accordingly. The model was then used in simulating each of the 36 steady-state periods achieved in the pilot plant. The details are given in this Volume one. This Volume 2 provides details of the carbonizer data reconciliation.

  9. Variability of Bed Drag on Cohesive Beds under Wave Action

    Directory of Open Access Journals (Sweden)

    Ilgar Safak

    2016-04-01

    Full Text Available Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law, a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10 - 4 m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  10. Variability of bed drag on cohesive beds under wave action

    Science.gov (United States)

    Safak, Ilgar

    2016-01-01

    Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law), a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10  m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold) with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  11. Test bed for real-time image acquisition and processing systems based on FlexRIO, CameraLink, and EPICS

    Energy Technology Data Exchange (ETDEWEB)

    Barrera, E., E-mail: eduardo.barrera@upm.es [Grupo de Investigación en Instrumentación y Acústica Aplicada, Universidad Politécnica de Madrid (UPM) (Spain); Ruiz, M.; Sanz, D. [Grupo de Investigación en Instrumentación y Acústica Aplicada, Universidad Politécnica de Madrid (UPM) (Spain); Vega, J.; Castro, R. [Asociación EURATOM/CIEMAT para Fusión, Madrid (Spain); Juárez, E.; Salvador, R. [Centro de Investigación en Tecnologías Software y Sistemas Multimedia para la Sostenibilidad, Universidad Politécnica de Madrid (UPM) (Spain)

    2014-05-15

    Highlights: • The test bed allows for the validation of real-time image processing techniques. • Offers FPGA (FlexRIO) image processing that does not require CPU intervention. • Is fully compatible with the architecture of the ITER Fast Controllers. • Provides flexibility and easy integration in distributed experiments based on EPICS. - Abstract: Image diagnostics are becoming standard ones in nuclear fusion. At present, images are typically analyzed off-line. However, real-time processing is occasionally required (for instance, hot-spot detection or pattern recognition tasks), which will be the objective for the next generation of fusion devices. In this paper, a test bed for image generation, acquisition, and real-time processing is presented. The proposed solution is built using a Camera Link simulator, a Camera Link frame-grabber, a PXIe chassis, and offers software interface with EPICS. The Camera Link simulator (PCIe card PCIe8 DVa C-Link from Engineering Design Team) generates simulated image data (for example, from video-movies stored in fusion databases) using a Camera Link interface to mimic the frame sequences produced with diagnostic cameras. The Camera Link frame-grabber (FlexRIO Solution from National Instruments) includes a field programmable gate array (FPGA) for image acquisition using a Camera Link interface; the FPGA allows for the codification of ad-hoc image processing algorithms using LabVIEW/FPGA software. The frame grabber is integrated in a PXIe chassis with system architecture similar to that of the ITER Fast Controllers, and the frame grabber provides a software interface with EPICS to program all of its functionalities, capture the images, and perform the required image processing. The use of these four elements allows for the implementation of a test bed system that permits the development and validation of real-time image processing techniques in an architecture that is fully compatible with that of the ITER Fast Controllers

  12. CIRCULATING MOVING BED COMBUSTION PROOF OF CONCEPT

    Energy Technology Data Exchange (ETDEWEB)

    Jukkola, Glen

    2010-06-30

    Circulating Moving Bed (CMB) combustion technology has its roots in traditional circulating fluidized bed technology and involves a novel method of solid fuel combustion and heat transfer. CMB technology represents a step change in improved performance and cost relative to conventional PC and FBC boilers. The CMB heat exchanger preheats the energy cycle working fluid, steam or air, to the high temperature levels required in systems for advanced power generation. Unique features of the CMB are the reduction of the heat transfer surfaces by about 60% as a result of the enhanced heat transfer rates, flexibility of operation, and about 30% lower cost over existing technology. The CMB Phase I project ran from July 2001 through March 2003. Its objective was to continue development of the CMB technology with a series of proof of concept tests. The tests were conducted at a scale that provided design data for scale up to a demonstration plant. These objectives were met by conducting a series of experiments in ALSTOM Power’s Multi-use Test Facility (MTF). The MTF was modified to operate under CMB conditions of commercial interest. The objective of the tests were to evaluate gas-to-solids heat transfer in the upper furnace, assess agglomeration in the high temperature CMB bubbling bed, and evaluate solids-to-tube heat transfer in the moving bed heat exchanger. The Phase I program results showed that there are still some significant technical uncertainties that needed to be resolved before the technology can be confidently scaled up for a successful demonstration plant design. Work remained in three primary areas: • scale up of gas to solid heat transfer • high temperature finned surface design • the overall requirements of mechanical and process design. The CMB Phase II workscope built upon the results of Phase I and specifically addressed the remaining technical uncertainties. It included a scaled MTF heat transfer test to provide the necessary data to scale up gas

  13. Testing of a new mining system performance at narrow coal bed; Ensayo de un sistema de arranque con cepillo mediante accionamiento hidraulico para capas estrechas de carbon

    Energy Technology Data Exchange (ETDEWEB)

    1999-09-01

    This researching project had the aim of: Testing a new mining system performance at narrow coal bed, which uses plough equipment with hydraulic driving devices. Minimising driving power group size to avoid problems regarding with the wall mining-heading transition, decreasing the needed room to house it and thus, simplifying wall mining edge support. The expected goals were: Take advantage of hydraulic driving devices to obtain a good efficiency with a variable and discontinuous load, but without loosing the electric driving devices advantages, consisting on increase driving torque, being the engine blocked Lengthen the mechanical equipment life (chains, driving sprockets, etc) Reach an economic production rate Researching project was developed in El Bierzo basin (leon, Spain), in Grupo Ampliacion, a mining group belonged to Viloria Hnos, S. A. (Author)

  14. Fate of Majorana Modes in CeCoIn_{5}/YbCoIn_{5} Superlattices: A Test Bed for the Reduction of Topological Classification.

    Science.gov (United States)

    Yoshida, Tsuneya; Daido, Akito; Yanase, Youichi; Kawakami, Norio

    2017-04-07

    In this paper, we propose CeCoIn_{5}/YbCoIn_{5} superlattice systems as a test bed for the reduction of topological classification in free fermions. We find that the system with a quadlayer of CeCoIn_{5} shows a topological crystalline superconducting phase with the mirror Chern number eight at the noninteracting level. Furthermore, we demonstrate that in the presence of two-body interactions, gapless edge modes are no longer protected by the symmetry in the system with a quadlayer, but are protected in the system with a bilayer or trilayer. This clearly exemplifies the reduction of topological classification from Z⊕Z to Z⊕Z_{8}.

  15. Swift J1644+57: an Ideal Test Bed of Radiation Mechanisms in a Relativistic Super-Eddington Jet

    CERN Document Server

    Crumley, Patrick; Santana, Rodolfo; Hernández, Roberto A; Kumar, Pawan; Markoff, Sera

    2016-01-01

    Within the first 10 days after Swift discovered the jetted tidal disruption event (TDE) Sw J1644+57, simultaneous observations in the radio, near-infrared, optical, X-ray and gamma-ray bands were carried out. These multiwavelength data provide a unique opportunity to constrain the emission mechanism and make-up of a relativistic super-Eddington jet. We consider an exhaustive variety of radiation mechanisms for the generation of X-rays in this TDE, and rule out many processes such as SSC, photospheric and proton synchrotron. The infrared to gamma-ray data for Sw J1644+57 are consistent with synchrotron and external-inverse-Compton (EIC) processes provided that electrons in the jet are continuously accelerated on a time scale shorter than ~1% of the dynamical time to maintain a power-law distribution. The requirement of continuous electron acceleration points to magnetic reconnection in a Poynting flux dominated jet. The EIC process may require fine tuning to explain the observed temporal decay of the X-ray lig...

  16. Guidance and Navigation Software Architecture Design for the Autonomous Multi-Agent Physically Interacting Spacecraft (AMPHIS) Test Bed

    Science.gov (United States)

    2006-12-01

    class, the Jules Verne successfully completed the autonomous rendezvous and docking system in Europe’s largest ship hull test facility in September...replicate the 2007 Jules Verne mission. http://www.esa.int/SPECIALS/ATV/SEMWCEKKKSE_0.html. 23. Banke, K., Air Force XSS-10 Micro-Satellite Mission a

  17. Underground gasification for steeply dipping coal beds: Phase III. Quarterly progress report, April 1-June 30, 1981. [Rawlins Test 2

    Energy Technology Data Exchange (ETDEWEB)

    1981-12-01

    Preparations are being made for the August start-up of Rawlins Test 2. Site construction activities began May 4 with the mobilization of the construction subcontractor. The drilling program was completed this quarter with the installation of instrumentation wells. The Experimental Basis Document, PGA Operating Manual, and DAS Operating Manual have also been completed.

  18. Bed rest during pregnancy

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/patientinstructions/000581.htm Bed rest during pregnancy To use the sharing features on ... few days or weeks. This is called bed rest. Bed rest used to be recommended routinely for ...

  19. H{sub 2}S removal from coal gas at elevated temperature and pressure in fluidized bed with zinc titanate sorbents. 1. Cyclic tests

    Energy Technology Data Exchange (ETDEWEB)

    Mojtahedi, W.; Abbasian, J. [Enviropower Inc., Espoo (Finland)

    1995-05-01

    Simplified integrated gasification combined cycle (IGCC) processes are considered to be among the most efficient and environmentally acceptable technologies for power generation from coal. In such processes the coal is gasified at pressure and the coal gas is cleaned and combusted in a gas turbine. Coal gas cleanup at elevated pressure and temperature in the IGCC processes offers advantages in higher power generation efficiency and simpler plant configuration. Regenerable mixed metal oxide sorbents are the prime candidates for removal of hydrogen sulfide (the main pollutant) from the hot coal gas in the simplified IGCC processes. In this paper, the results of cyclic sulfidation/regeneration tests conducted with two zinc titanate sorbents are presented and discussed. These tests were carried out at high pressure and temperature (20 bar, 550-650{degree}C) in a bench-scale fluidized-bed reactor. The results indicate that the reactivity of both sorbents towards H{sub 2}S gradually decline in cyclic sulfidation/regeneration tests. 20 refs., 11 figs., 4 tabs.

  20. Noradrenergic neurotransmission within the bed nucleus of the stria terminalis modulates the retention of immobility in the rat forced swimming test.

    Science.gov (United States)

    Nagai, Michelly M; Gomes, Felipe V; Crestani, Carlos C; Resstel, Leonardo B M; Joca, Sâmia R L

    2013-06-01

    The bed nucleus of the stria terminalis (BNST) is a limbic structure that has a direct influence on the autonomic, neuroendocrine, and behavioral responses to stress. It was recently reported that reversible inactivation of synaptic transmission within this structure causes antidepressant-like effects, indicating that activation of the BNST during stressful situations would facilitate the development of behavioral changes related to the neurobiology of depression. Moreover, noradrenergic neurotransmission is abundant in the BNST and has an important role in the regulation of emotional processes related to the stress response. Thus, this study aimed to test the hypothesis that activation of adrenoceptors within the BNST facilitates the development of behavioral consequences of stress. To investigate this hypothesis, male Wistar rats were stressed (forced swimming, 15 min) and 24 h later received intra-BNST injections of vehicle, WB4101, RX821002, CGP20712, or ICI118,551, which are selective α(1), α(2), β(1), and β(2) adrenoceptor antagonists, respectively, 10 min before a 5-min forced swimming test. It was observed that administration of WB4101 (10 and 15 nmol), CGP20712 (5 and 10 nmol), or ICI118,551 (5 nmol) into the BNST reduced the immobility time of rats subjected to forced swimming test, indicating an antidepressant-like effect. These findings suggest that activation of α(1), β(1), and β(2) adrenoceptors in the BNST could be involved in the development of the behavioral consequences of stress.

  1. Numerical Relativity for Inspiraling Binaries in Co-Rotating Coordinates: Test Bed for Lapse and Shift Equations

    OpenAIRE

    Thorne, Kip S.

    1998-01-01

    Gravitational-wave data analysis requires a detailed understanding of the highly relativistic, late stages of inspiral of neutron-star and black-hole binaries. A promising method to compute the late inspiral and its emitted waves is numerical relativity in co-rotating coordinates. The coordinates must be kept co-rotating via an appropriate choice of numerical relativity's lapse and shift functions. This article proposes a model problem for testing the ability of various lapse and shift prescr...

  2. Simultaneous dioxin and mercury collection in a filter bed reactor; Process concepts and test results. Simultane Dioxin- und Quecksilberabscheidung im Filterschichtreaktor; Verfahrenskonzepte und Versuchsergebnisse

    Energy Technology Data Exchange (ETDEWEB)

    Weirich, W. (Deutsche Babcock Anlagen GmbH, Oberhausen (Germany)); Glinka, U. (Deutsche Babcock Anlagen GmbH, Oberhausen (Germany)); Ruther, G. (Deutsche Babcock Anlagen GmbH, Oberhausen (Germany))

    1993-03-01

    In the process chain dealt with in this paper, which uses a combined SCR reactor and filter bed reactor where the most far-reaching catalytic destruction of NO[sub x] and dioxins is obtained, the filter bed reactor was operated as a pilot plant using an inexpensive additive with multiple recycling. (orig.)

  3. Follow on Research for Multi-Utility Technology Test Bed Aircraft at NASA Dryden Flight Research Center (FY13 Progress Report)

    Science.gov (United States)

    Pak, Chan-Gi

    2013-01-01

    Modern aircraft employ a significant fraction of their weight in composite materials to reduce weight and improve performance. Aircraft aeroservoelastic models are typically characterized by significant levels of model parameter uncertainty due to the composite manufacturing process. Small modeling errors in the finite element model will eventually induce errors in the structural flexibility and mass, thus propagating into unpredictable errors in the unsteady aerodynamics and the control law design. One of the primary objectives of Multi Utility Technology Test-bed (MUTT) aircraft is the flight demonstration of active flutter suppression, and therefore in this study, the identification of the primary and secondary modes for the structural model tuning based on the flutter analysis of MUTT aircraft. The ground vibration test-validated structural dynamic finite element model of the MUTT aircraft is created in this study. The structural dynamic finite element model of MUTT aircraft is improved using the in-house Multi-disciplinary Design, Analysis, and Optimization tool. In this study, two different weight configurations of MUTT aircraft have been improved simultaneously in a single model tuning procedure.

  4. Longitudinal emittance blow-up and hollow bunches with arbitrarily-shaped noise in the SPS as LHC test-bed

    CERN Document Server

    Bohl, Thomas; Shaposhnikova, E; Tückmantel, Joachim; CERN. Geneva. AB Department

    2008-01-01

    In the SPS the LHC type high intensity beam can be kept stable longitudinally during acceleration to 450 GeV/c by using the 800 MHz higher harmonic system and, in addition, by making a longitudinal controlled emittance increase by a factor of about 1.5. This latter is obtained by applying band-limited RF phase noise via the main RF system. In LHC itself, which does not have a higher harmonic system, an emittance increase by a factor 2.5 is required. This was attempted in the SPS, as a test-bed for LHC, with shaped RF phase noise and with the 800 MHz system switched off - limiting the maximum stable beam intensity. The emittance of a single (LHC-) pilot bunch has been blown up to a factor 2.5 in coast at 270 GeV/c with a final ‘good’ bunch shape. It remains to be demonstrated that this technique can also be applied successfully for many high intensity bunches with differing synchrotron frequency profiles along the batches. Also a first very quick test to create hollow bunches was done.

  5. Design of High Frequency Induction Plate Forming Test-Bed%高频感应弯板成形试验台设计

    Institute of Scientific and Technical Information of China (English)

    刘守法; 范平

    2012-01-01

    Specific to the present situation of the lack of high frequency induction plate forming experimental equipment at home and abroad, a high frequency induction plate forming test梑ed was designed to conduct high frequency induction plate forming test,which will be helpful to study the law of the high frequency induction plate forming.The finite element analysis for tine plate forming model was conducted with Ansys software and the plate forming test was also completed on the test-bed under the scam parameters After comparing the bending angle curves of the finite element analysis with the experimental,it is observed that the two bending angle curves are basically the same to each other and the bending angle error between the simulation and the test is kss than 12.1%.%针对国内外高频感应弯板成形试验设备缺乏现状,设计了弯板成形试验台,用于进行高频感应弯板成形试验,进而有助于研究高频感应弯板成形规律.利用Ansys软件对弯板成形模型进行了有限元分析,并利用试验台进行了相同参数下板料成形试验,将有限元分析得到的折弯角度曲线与试验得到的实际折弯角度曲线进行了对比,结果表明:有限元分析得到的板料折弯角度曲线与试验得到的板料折弯角度曲线基本相同,二者折弯角度偏差小于12.1%.

  6. Design and Testing of a Labview- Controlled Catalytic Packed- Bed Reactor System For Production of Hydrocarbon Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Street, J.; Yu, F.; Warnock, J.; Wooten, J.; Columbus, E.; White, M. G.

    2012-05-01

    Gasified woody biomass (producer gas) was converted over a Mo/H+ZSM-5 catalyst to produce gasolinerange hydrocarbons. The effect of contaminants in the producer gas showed that key retardants in the system included ammonia and oxygen. The production of gasoline-range hydrocarbons derived from producer gas was studied and compared with gasoline-range hydrocarbon production from two control syngas mixes. Certain mole ratios of syngas mixes were introduced into the system to evaluate whether or not the heat created from the exothermic reaction could be properly controlled. Contaminant-free syngas was used to determine hydrocarbon production with similar mole values of the producer gas from the gasifier. Contaminant-free syngas was also used to test an ideal contaminant-free synthesis gas situation to mimic our particular downdraft gasifier. Producer gas was used in this study to determine the feasibility of using producer gas to create gasoline-range hydrocarbons on an industrial scale using a specific Mo/H+ZSM-5 catalyst. It was determined that after removing the ammonia, other contaminants poisoned the catalyst and retarded the hydrocarbon production process as well.

  7. Examination of Communication Delays on Team Performance: Utilizing the International Space Station (ISS) as a Test Bed for Analog Research

    Science.gov (United States)

    Keeton, K. E.; Slack, K, J.; Schmidt, L. L.; Ploutz-Snyder, R.; Baskin, P.; Leveton, L. B.

    2011-01-01

    Operational conjectures about space exploration missions of the future indicate that space crews will need to be more autonomous from mission control and operate independently. This is in part due to the expectation that communication quality between the ground and exploration crews will be more limited and delayed. Because of potential adverse effects on communication quality, both researchers and operational training and engineering experts have suggested that communication delays and the impact these delays have on the quality of communications to the crew will create performance decrements if crews are not given adequate training and tools to support more autonomous operations. This presentation will provide an overview of a research study led by the Behavioral Health and Performance Element (BHP) of the NASA Human Research Program that examines the impact of implementing a communication delay on ISS on individual and team factors and outcomes, including performance and related perceptions of autonomy. The methodological design, data collection efforts, and initial results of this study to date will be discussed . The results will focus on completed missions, DRATS and NEEMO15. Lessons learned from implementing this study within analog environments will also be discussed. One lesson learned is that the complexities of garnishing a successful data collection campaign from these high fidelity analogs requires perseverance and a strong relationship with operational experts. Results of this study will provide a preliminary understanding of the impact of communication delays on individual and team performance as well as an insight into how teams perform and interact in a space-like environment . This will help prepare for implementation of communication delay tests on the ISS, targeted for Increment 35/36.

  8. High-resolution Digital Mapping of Historical Lava Flows as a Test-bed for Lava Flow Models

    Science.gov (United States)

    Pyle, D. M.; Parks, M.; Nomikou, P.; Mather, T. A.; Simou, E.; Kalnins, L. M.; Paulatto, M.; Watts, A. B.

    2013-12-01

    eruption volume and pre-eruption interval, which will in turn improve our capacity to forecast the size and duration of future dome-forming events at Santorini. The new topographic dataset, and the detailed historical accounts of the eruptions which formed those lava flows, offers a tremendous opportunity to test the current generation of lava flow models.

  9. A New Class of Advanced Accuracy Satellite Instrumentation (AASI) for the CLARREO Mission: Interferometer Test-bed Tradestudies and Selection

    Science.gov (United States)

    Taylor, J. K.; Revercomb, H. E.; Grandmont, F. J.; Buijs, H.; Gero, P. J.; Best, F. A.; Tobin, D. C.; Knuteson, R. O.; Laporte, D. D.

    2009-12-01

    uniformly fill the sensor field-of-view, and (4) Dual Absolute Radiance Interferometers (DARI), providing spectral coverage from 6 to 50 micrometers that can be inter-compared to dissect any unexpected systematic errors in overlapping spectral regions. Interferometer trade-studies for the UW DARI have been conducted and the design selection is complete. Instrument assembly, integration, testing and verification will begin in early 2010. The interferometer trade-study and design details will be presented herein.

  10. Diabetes: Unique to Older Adults

    Science.gov (United States)

    ... Stroke Urinary Incontinence Related Documents PDF Choosing Wisely: Diabetes Tests and Treatments Download Related Video Join our e-newsletter! Aging & Health A to Z Diabetes Unique to Older Adults This section provides information ...

  11. Earth-moon Lagrangian points as a test bed for general relativity and effective field theories of gravity

    Science.gov (United States)

    Battista, Emmanuele; Dell'Agnello, Simone; Esposito, Giampiero; Di Fiore, Luciano; Simo, Jules; Grado, Aniello

    2015-09-01

    equilibrium we find quantum corrections below a millimeter. In the latter case, for the point L1, general relativity corrects Newtonian theory by 7.61 m, comparable, as an order of magnitude, with the lunar geodesic precession of about 3 m per orbit. The latter is a cumulative effect accurately measured at the centimeter level through the lunar laser ranging positioning technique. Thus, it is possible to study a new laser ranging test of general relativity to measure the 7.61 m correction to the L1 Lagrangian point, an observable never used before in the Sun-Earth-Moon system. Performing such an experiment requires controlling the propulsion to precisely reach L1, using an instrumental accuracy comparable to the measurement of the lunar geodesic precession, and understanding systematic effects resulting from thermal radiation and multibody gravitational perturbations. This will then be the basis to consider a second-generation experiment to study deviations of effective field theories of gravity from general relativity in the Sun-Earth-Moon system.

  12. Integration of a Higher Plant Chamber into the European Space Agency's MELiSSA Pilot Plant: The Canadian Role in Advanced Life Support Test-Bed Development

    Science.gov (United States)

    Waters, Geoffrey; Lawson, Jamie; Gidzinski, Danuta; Stasiak, Michael; Dixon, Mike; Peiro, Enrique; Godia, Francesc; Paille, Christel; Fossen, Arnaud; Lamaze, Brigitte; Lasseur, Christophe

    The European Space Agency's Micro-Ecological Life Support System Alternative (MELiSSA) project has been conceived as a tool for developing the technology of future biological life support systems required for long-term human space exploration missions to the Moon or Mars. The main life support functions of MELiSSA are the recycling of waste (inedible plant biomass, human excrement), carbon dioxide and minerals and the production of food, fresh water and air revitalization. Based on the principle of an aquatic ecosystem, MELiSSA is comprised of four microbial compartments and a higher plant compartment integrated in a closed loop. Each compartment is studied, designed and demonstrated at laboratory scale before being scaled-up for subsequent integration into the MELISSA Pilot Plant (MPP) at the Universitat Aut`noma de Barcelona. Work related to higher plant cultivation systems, o which have been historically focussed at the University of Guelph's Controlled Environment Systems Research Facility (CESRF), has included design of the HPC for the MPP, the metabolic characterization of MELiSSA candidate crops and the validation of theoretical gas exchange and nutrient dynamic models, The presented paper will review some of the recent data and HPC design work of CESRF conducted as part of Canada's involvement in the MELiSSA program and its partnership in the development of the MPP terrestrial demonstration test-bed.

  13. Trace Gas Measurements from the GeoTASO and GCAS Airborne Instruments: An Instrument and Algorithm Test-Bed for Air Quality Observations from Geostationary Orbit

    Science.gov (United States)

    Nowlan, C. R.; Liu, X.; Janz, S. J.; Leitch, J. W.; Al-Saadi, J. A.; Chance, K.; Cole, J.; Delker, T.; Follette-Cook, M. B.; Gonzalez Abad, G.; Good, W. S.; Kowalewski, M. G.; Loughner, C.; Pickering, K. E.; Ruppert, L.; Soo, D.; Szykman, J.; Valin, L.; Zoogman, P.

    2016-12-01

    The Geostationary Trace gas and Aerosol Sensor Optimization (GeoTASO) and the GEO-CAPE Airborne Simulator (GCAS) instruments are pushbroom sensors capable of making remote sensing measurements of air quality and ocean color. Originally developed as test-bed instruments for the Geostationary Coastal and Air Pollution Events (GEO-CAPE) decadal survey, these instruments are now also part of risk reduction for the upcoming Tropospheric Emissions: Monitoring of Pollution (TEMPO) and Geostationary Environment Monitoring Spectrometer (GEMS) geostationary satellite missions, and will provide validation capabilities after the satellite instruments are in orbit. GeoTASO and GCAS flew on two different aircraft in their first intensive air quality field campaigns during the DISCOVER-AQ missions over Texas in 2013 and Colorado in 2014. GeoTASO was also deployed in 2016 during the KORUS-AQ field campaign to make measurements of trace gases and aerosols over Korea. GeoTASO and GCAS collect spectra of backscattered solar radiation in the UV and visible that can be used to derive 2-D maps of trace gas columns below the aircraft at spatial resolutions on the order of 250 x 500 m. We present spatially resolved maps of trace gas retrievals of ozone, nitrogen dioxide, formaldehyde and sulfur dioxide over urban areas and power plants from flights during the field campaigns, and comparisons with data from ground-based spectrometers, in situ monitoring instruments, and satellites.

  14. C-Band Airport Surface Communications System Standards Development. Phase II Final Report. Volume 2: Test Bed Performance Evaluation and Final AeroMACS Recommendations

    Science.gov (United States)

    Hall, Edward; Magner, James

    2011-01-01

    This report is provided as part of ITT s NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: New ATM Requirements-Future Communications, C-Band and L-Band Communications Standard Development and was based on direction provided by FAA project-level agreements for New ATM Requirements-Future Communications. Task 7 included two subtasks. Subtask 7-1 addressed C-band (5091- to 5150-MHz) airport surface data communications standards development, systems engineering, test bed and prototype development, and tests and demonstrations to establish operational capability for the Aeronautical Mobile Airport Communications System (AeroMACS). Subtask 7-2 focused on systems engineering and development support of the L-band digital aeronautical communications system (L-DACS). Subtask 7-1 consisted of two phases. Phase I included development of AeroMACS concepts of use, requirements, architecture, and initial high-level safety risk assessment. Phase II builds on Phase I results and is presented in two volumes. Volume I is devoted to concepts of use, system requirements, and architecture, including AeroMACS design considerations. Volume II (this document) describes an AeroMACS prototype evaluation and presents final AeroMACS recommendations. This report also describes airport categorization and channelization methodologies. The purposes of the airport categorization task were (1) to facilitate initial AeroMACS architecture designs and enable budgetary projections by creating a set of airport categories based on common airport characteristics and design objectives, and (2) to offer high-level guidance to potential AeroMACS technology and policy development sponsors and service providers. A channelization plan methodology was developed because a common global methodology is needed to assure seamless interoperability among diverse AeroMACS services potentially supplied by multiple service providers.

  15. The Squad Performance Test Bed

    Science.gov (United States)

    2014-06-01

    2 Cafeteria Talk out Loud Team Member 24.1 16 Officer 2 Cafeteria Talk out Loud Whole Team 4.0 2 Officer 2 Cafeteria Talk into Radio Dispatch 10.1 3...Officer 2 Cafeteria Using Hand Signals Team Member 3.6 2 Officer 2 Cafeteria Firing a Weapon Perpetrator N/A 8 Officer 2 Hallway from Cafeteria to...Second Floor Talk out Loud Injured Victim 4.5 1 Officer 2 Hallway from Cafeteria to Second Floor Talk out Loud Team Member 58.0 14 Officer 2 Hallway from

  16. Big Data Analytics Test Bed

    Science.gov (United States)

    2013-09-01

    System IaaS Infrastructure as a Service IP Internet Protocol IPv4 Internet Protocol Version 4 IPv6 Internet Protocol Version 6 IT Information...adoption due to its scalability, elasticity, mobility , and reduced overhead. Most organizations, whether DoD or civilian, are seeking to reduce the...global ecommerce, popularity of smart mobile devices, and the data collection from sensors and 11 ubiquitous computing devices. For these

  17. Mars Ecopoiesis Test Bed Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Ecopoiesis is the concept of initiating life in a new place; more precisely, the creation of an ecosystem capable of supporting life. It is the concept of initiating...

  18. Anomalous Dispersion in a Sand Bed River

    Science.gov (United States)

    Bradley, D. N.; Tucker, G. E.; Benson, D. M.

    2009-04-01

    There has been a recent surge of interest in non-local, heavy-tailed models of sediment transport and dispersion that are governed by fractional order differential equations. These models have a firm mathematical foundation and have been successfully applied in a variety of transport systems, but their use in geomorphology has been minimal because the data required to validate the models is difficult to acquire. We use data from a nearly 50-year-old tracer experiment to test a fluvial bed load transport model with a two unique features. First, the model uses a heavy-tailed particle velocity distribution with a divergent second moment to reproduce the anomalously high fraction of tracer mass observed in the downstream tail of the spatial distribution. Second, the model partitions mass into a detectable mobile phase and an undetectable, immobile phase. This two-phase transport model predicts two other features observed in the data: a decrease in the amount of detected tracer mass over the course of the experiment and the high initial velocity of the tracer plume. Because our model uses a heavy-tailed velocity distribution with a divergent second moment it is non-local and non-Fickian and able to reproduce aspects of the data that a local, Fickian model cannot. The model's successful prediction of the observed concentration profiles provides some of the first evidence of anomalous dispersion of bed load in a natural river.

  19. Measurement of hand dynamics in a microsurgery environment: Preliminary data in the design of a bimanual telemicro-operation test bed

    Science.gov (United States)

    Charles, Steve; Williams, Roy

    1989-01-01

    Data describing the microsurgeon's hand dynamics was recorded and analyzed in order to provide an accurate model for the telemicrosurgery application of the Bimanual Telemicro-operation Test Bed. The model, in turn, will guide the development of algorithms for the control of robotic systems in bimanual telemicro-operation tasks. Measurements were made at the hand-tool interface and include position, acceleration and force between the tool-finger interface. Position information was captured using an orthogonal pulsed magnetic field positioning system resulting in measurements in all six degrees-of-freedom (DOF). Acceleration data at the hands was obtained using accelerometers positioned in a triaxial arrangement on the back of the hand allowing measurements in all three cartesian-coordinate axes. Force data was obtained by using miniature load cells positioned between the tool and the finger and included those forces experienced perpendicular to the tool shaft and those transferred from the tool-tissue site. Position data will provide a minimum/maximum reference frame for the robotic system's work space or envelope. Acceleration data will define the response times needed by the robotic system in order to emulate and subsequently outperform the human operator's tool movements. The force measurements will aid in designing a force-reflective, force-scaling system as well as defining the range of forces the robotic system will encounter. All analog data was acquired by a 16-channel analog-to-digital conversion system residing in a IBM PC/AT-compatible computer at the Center's laboratory. The same system was also used to analyze and present the data.

  20. 2009 PILOT SCALE FLUIDIZED BED STEAM REFORMING TESTING USING THE THOR (THERMAL ORGANIC REDUCTION) PROCESS: ANALYTICAL RESULTS FOR TANK 48H ORGANIC DESTRUCTION - 10408

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M.; Jantzen, C.; Burket, P.; Crawford, C.; Daniel, G.; Aponte, C.; Johnson, C.

    2009-12-28

    The Savannah River Site (SRS) must empty the contents of Tank 48H, a 1.3 million gallon Type IIIA HLW storage tank, to return this tank to service. The tank contains organic compounds, mainly potassium tetraphenylborate that cannot be processed downstream until the organic components are destroyed. The THOR{reg_sign} Treatment Technologies (TTT) Fluidized Bed Steam Reforming (FBSR) technology, herein after referred to as steam reforming, has been demonstrated to be a viable process to remove greater than 99.9% of the organics from Tank 48H during various bench scale and pilot scale tests. These demonstrations were supported by Savannah River Remediation (SRR) and the Department of Energy (DOE) has concurred with the SRR recommendation to proceed with the deployment of the FBSR technology to treat the contents of Tank 48H. The Savannah River National Laboratory (SRNL) developed and proved the concept with non-radioactive simulants for SRR beginning in 2003. By 2008, several pilot scale campaigns had been completed and extensive crucible testing and bench scale testing were performed in the SRNL Shielded Cells using Tank 48H radioactive sample. SRNL developed a Tank 48H non-radioactive simulant complete with organic compounds, salt, and metals characteristic of those measured in a sample of the radioactive contents of Tank 48H. FBSR Pilot Scaled Testing with the Tank 48H simulant has demonstrated the ability to remove greater than 98% of the nitrites and greater than 99.5% of the nitrates from the Tank 48H simulant, and to form a solid product that is primarily alkali carbonate. The alkali carbonate is soluble and, thus, amenable to pumping as a liquid to downstream facilities for processing. The FBSR technology was demonstrated in October of 2006 in the Engineering Scale Test Demonstration (ESTD) pilot scale steam reformer at the Hazen Research Inc. (HRI) facility in Golden, CO. Additional ESTD tests were completed in 2008 and in 2009 that further demonstrated the

  1. K Basin Sludge Conditioning Process Testing Project Results from Test 4, ''Acid Digestion of Mixed-Bed Ion Exchange Resin''

    Energy Technology Data Exchange (ETDEWEB)

    Pool, K.H.; Delegard, C.H.; Schmidt, A.J.; Thornton, B.M.; Silvers, K.L.

    1999-04-02

    Approximately 73 m{sup 3} of heterogeneous solid material, ''sludge,'' (upper bound estimate, Packer 1997) have accumulated at the bottom of the K Basins in the 100 K Area of the Hanford Site. This sludge is a mixture of spent fuel element corrosion products, ion exchange materials (organic and inorganic), graphite-based gasket materials, iron and aluminum metal corrosion products, sand, and debris (Makenas et al. 1996, 1997). In addition, small amounts of polychlorinated biphenyls (PCBs) have been found. Ultimately, it is planned to transfer the K Basins sludge to the Hanford double shell tanks (DSTs). The Hanford Spent Nuclear Fuel (HSNF) project has conducted a number of evaluations to examine technology and processing alternatives to pretreat K Basin sludge to meet storage and disposal requirements. From these evaluations, chemical pretreatment has been selected to address criticality issues, reactivity, and the destruction or removal of PCBs before the K Basin sludge can be transferred to the DSTs. Chemical pretreatment, referred to as the K Basin sludge conditioning process, includes nitric acid dissolution of the sludge (with removal of acid insoluble solids), neutrons absorber addition, neutralization, and reprecipitation. Laboratory testing is being conducted by the Pacific Northwest National Laboratory (PNNL) to provide data necessary to develop the sludge conditioning process.

  2. Bed Bugs - Multiple Languages

    Science.gov (United States)

    ... Are Here: Home → Multiple Languages → All Health Topics → Bed Bugs URL of this page: https://medlineplus.gov/languages/ ... V W XYZ List of All Topics All Bed Bugs - Multiple Languages To use the sharing features on ...

  3. Bed Bugs and Schools

    Science.gov (United States)

    Bed bugs have long been a pest – feeding on blood, causing itchy bites and generally irritating their human hosts. They are successful hitchhikers, and can move from an infested site to furniture, bedding, baggage, boxes, and clothing.

  4. Critical conditions of bed sediment entrainment due to debris flow

    Directory of Open Access Journals (Sweden)

    M. Papa

    2004-01-01

    Full Text Available The present study describes entrainment characteristics of bed material into debris flow, based on flume tests, numerical and dimensional analyses. Flume tests are conducted to investigate influences of bed sediment size on erosion rate by supplying debris flows having unsaturated sediment concentration over erodible beds. Experimental results show that the erosion rate decreases monotonically with increase of sediment size, although erosion rate changes with sediment concentration of debris flow body. In order to evaluate critical condition of bed sediment entrainment, a length scale which measures an effective bed shear stress is introduced. The effective bed shear stress is defined as total shear stress minus yield stress on the bed surface. The results show that critical entrainment conditions can be evaluated well in terms of Shields curve using the effective bed shear stress instead of a usual bed shear stress.

  5. Classifying bed inclination using pressure images.

    Science.gov (United States)

    Baran Pouyan, M; Ostadabbas, S; Nourani, M; Pompeo, M

    2014-01-01

    Pressure ulcer is one of the most prevalent problems for bed-bound patients in hospitals and nursing homes. Pressure ulcers are painful for patients and costly for healthcare systems. Accurate in-bed posture analysis can significantly help in preventing pressure ulcers. Specifically, bed inclination (back angle) is a factor contributing to pressure ulcer development. In this paper, an efficient methodology is proposed to classify bed inclination. Our approach uses pressure values collected from a commercial pressure mat system. Then, by applying a number of image processing and machine learning techniques, the approximate degree of bed is estimated and classified. The proposed algorithm was tested on 15 subjects with various sizes and weights. The experimental results indicate that our method predicts bed inclination in three classes with 80.3% average accuracy.

  6. Introduction to Bed Bugs

    Science.gov (United States)

    ... that there are ways to control bed bugs. Getting good, solid information is the first step in both prevention and control. While there is no chemical quick fix, there are effective strategies to control bed bugs involving both non-chemical and chemical methods. Bed bugs can be hard to find and ...

  7. Determination of true bed thickness using folded bed model and borehole data

    Energy Technology Data Exchange (ETDEWEB)

    Xu, S.S.; Velasquillo-Martinez, L.G.; Grajales-Nishimura, J.M.; Murillo-Muneton, G. [Inst. Mexicano del Petroleo, Mexico City (Mexico); Garcia-Hernandez, J. [Petroleos Mexicanos Exploracion y Produccion, Tamaulipas (Mexico); Nieto-Samaniego, A.F. [Nacional Autonoma de Mexico Univ., Veracruz (Mexico). Centro de Geociencias

    2007-11-15

    The actual thickness of a given formation perpendicular to the bedding plane is known as the true bed thickness. Petroleum engineers rely on information regarding true bed thickness, particularly in dipping beds and in deviated holes because reservoir volume and isochore maps depend on these properties and not on the measured thickness. True bed thickness can be estimated from information gathered from well logs such as the dipmeter and borehole images. However, when deviations and dips exceed 10 degrees, corrections are needed. In this paper, a folded bed model was proposed to calculate the true bed thickness in the subsurface utilizing well log data. The value of true bed thickness (t) was shown to depend on the angle and the direction of the dip of the measured formation, as well as the drift angle and azimuth of the borehole. A case study from the Cantarell oil field in the southern Gulf of Mexico, offshore Campeche, was used to test the folded bed method. The model was shown to yield more uniform spatial change of the values of t, compared to the monoclinal bed model that often overestimates the average value of t. The maximum relative deviation of t from the monoclinal bed model reached 22.3 per cent and the maximum absolute deviation of t reached 34.5 m. The key factors that influence the values of t were found to be the bed dip, the dip difference between the top and base of the bed and the deviated angle of the well. The folded bed model yielded fewer changed values of the true bed thickness. 10 refs., 2 tabs., 9 figs.

  8. Collaborative Strategy on Bed Bugs

    Science.gov (United States)

    The Collaborative Strategy on Bed Bugs was developed by the Federal Bed Bug Workgroup to clarify the federal role in bed bug control and highlight ways that government, community, academia and private industry can work together on bed bug issues.

  9. Fluidized-bed combustion of gasification residue

    Energy Technology Data Exchange (ETDEWEB)

    Kudjoi, A.; Heinolainen, A.; Hippinen, I.; Lu, Y. [Helsinki University of Technology, Espoo (Finland). Lab. of Energy Economics and Power Plant Engineering

    1998-12-31

    Hybrid combined cycle processes have been presented as possibilities for power generation in the future. In the processes based on partial gasification of coal, the solid materials removed from a gasifier (i.e. fly ash and bed char) contain unburned fuel, which is burned either in an atmospheric or a pressurised fluidised-bed. Pressurised fluidised-bed (PFB) combustion of gasification residues were studied experimentally by Helsinki University of Technology. The gasification residues, i.e. cyclone fines and bed chars, came from pilot scale PFB gasification tests of bituminous coals. The combustion efficiency was high in cyclone fines combustion. The calcium sulphide oxidised effectively to calcium sulphate in the combustion of cyclone fines. In bed char combustion the residual sulphide contents in solids after combustion were still relatively high. In general, sulphur dioxide emissions in residue combustion were low. The recarbonation of calcium oxide was observed in bed char combustion. Fuel-N conversion to NO{sub x} during bed char combustion and in most of the test runs with cyclone fines was higher than in bituminous coal combustion. In bed char combustion the conversion was significantly higher than in cyclone fines combustion. NO{sub x} emissions increased with increasing excess air for both residues, as was expected. In bed char combustion the highest NO{sub x} emissions were measured at higher pressure. Calculated mass reactivity values of equal particle size of all bed chars studied had similar trends with burnout. The biggest particles had the lowest reactivity values throughout the combustion, while reactivity for finer particles was at considerably higher level and sharply increases with burnout. In the constant combustion conditions used in the tests, no significant differences were observed in rate-controlling mechanisms for bed char fractions studied. 25 refs., 13 figs., 15 tab.

  10. Carbonate chemistry dynamics over a Caribbean shelf reef (Cayo Enrique) at the Atlantic Ocean Acidification Test-bed, La Parguera, Puerto Rico

    Science.gov (United States)

    Gledhill, D. K.; Corredor, J. E.; Langdon, C.; Manzello, D.; Sabine, C. L.; Hensley, V.; Brocco, B.; Musielewicz, S.; Lawrence-Slavas, N.; Capella, J. E.

    2010-12-01

    Changes in surface ocean chemistry in direct response to rising atmospheric carbon dioxide (CO2) concentration may pose challenges to a range of marine ecosystems in coming decades. Monitoring this ocean acidification (OA) at regional and local-scales is an important requirement towards improving our understanding of the potential long-term consequences. Coral reef ecosystems are of particular concern given the potential effects OA may have on net community calcification and ultimately reef accretion rates. While the dynamics and trends in oceanic carbonate chemistry are reasonably well constrained, how OA is manifested within the shallow coastal waters where coral reef ecosystems reside is less understood. Community-scale metabolic processes impart an important control on near-reef carbonate chemistry. Constraining the near-reef variability in carbonate chemistry across diel, seasonal, and annual scales is a critical requirement towards assigning potential biogeochemical thresholds of OA. The Atlantic OA Test-bed in the La Parguera Marine Reserve, Puerto Rico was established in 2009 to provide sustained high temporal resolution monitoring of carbonate chemistry within an Atlantic tropical coral reef ecosystem. Presented here are the results of over a year’s worth of sustained monitoring at the Cayo Enrique forereef characterizing the temporal dynamics in carbonate chemistry. The Cayo Enrique reef is a source of CO2 to the atmosphere (1.7 mmol CO2 m-2 d-1, SE = 0.1) with both calcification and respiration serving to consistently elevate pCO2,sw relative to oceanic waters. Once pCO2,sw increase by a further 100 µatm in response to rising atmospheric CO2, these waters will likely reach undersaturation with respect to 13 mol % MgCO3 phases during winter months. While high-Mg calcites are prominent mineral phases of shallow tropical carbonate marine sediments, their relative importance as cementing agents of modern coral reef frameworks demands further investigation

  11. Pressurized fluidized-bed hydroretorting of eastern oil shales. Volume 2, Task 3, Testing of process improvement concepts: Final report, September 1987--May 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This final report, Volume 2, on ``Process Improvement Concepts`` presents the results of work conducted by the Institute of Gas Technology (IGT), the Illinois Institute of Technology (IIT), and the Ohio State University (OSU) to develop three novel approaches for desulfurization that have shown good potential with coal and could be cost-effective for oil shales. These are (1) In-Bed Sulfur Capture using different sorbents (IGT), (2) Electrostatic Desulfurization (IIT), and (3) Microbial Desulfurization and Denitrification (OSU and IGT). Results of work on electroseparation of shale oil and fines conducted by IIT is included in this report, as well as work conducted by IGT to evaluate the restricted pipe discharge system. The work was conducted as part of the overall program on ``Pressurized Fluidized-Bed Hydroretorting of Eastern Oil Shales.``

  12. Innovative Bed Load Measurement System for Large Alpine Gravel-Bed Rivers

    Science.gov (United States)

    Seitz, H.; Habersack, H. M.

    2009-04-01

    Samplers, Birckbeck-type bed load traps, etc.- in this regard used as a calibration technique but in general independent and throughout accepted bed load measurement methods) could be obtained. Finally in 2006, the measurement equipment was enlarged to an integrative and innovative bed load measurement system by installing Geophones. In addition hydrological, geological, meteorological and other related data are collected. For further investigations there is a chance to test new measurement techniques under well known boundary conditions at the fully equipped gauging stations. The instrumentation will allow observing transport processes in detail within the study reach. Calibration Measurements take place during the rainfall and snow melting season from May to August, furthermore in November due to Genoa depressions causing heavy rainfall in the catchment area of the Drau River. Especially the initiation of motion, the bed load transport rate and bed load transport processes (cross sectional variation, periodicity in bed load movement) are analysed. Moreover, for understanding bed load transport processes the initiation of motion is of central importance. As a result it could be shown that the counted number of geophone impulses per unit time is proportional to the transported sediment volume, calculated out of direct bed load measurements and the associated flow discharge. The scatter between geophone impulses, caused by bed load transport fluctuations, and flow discharge can be reduced if the sum of geophone impulses is averaged over longer time intervals (time lag between moving gravel sheet maximums is about 25 minutes). Furthermore, the assumed spatial and temporal variability of the bed load movement could now be proven. In addition it could be proven, that commonly used bed load predictors underestimate the measured bed load transport. In conclusion the results of the investigation are showing new aspects for understanding bed load transport processes. The installed

  13. Unique Path Partitions

    DEFF Research Database (Denmark)

    Bessenrodt, Christine; Olsson, Jørn Børling; Sellers, James A.

    2013-01-01

    We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions.......We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions....

  14. 汽车ABS试验台传感器与系统灵敏度的确定%Determination of Sensors and System Sensitivity in the Motor Vehicle ABS Test-bed

    Institute of Scientific and Technical Information of China (English)

    孙仁云

    2001-01-01

    According to the test parameters requirement on an Anti-lock Brake System (ABS) test-bed of the motor vehicle,some sensors are selected and arranged in its test system.It is elementary task to select sensors optimally in this research.In this paper,a selection and computing method of five sensors in the test-bed are expounded.The test system sensitivities are made sure on the basis of the sensors connected with instruments.The result of a debug has shown that the method is reasonable.%依据汽车防抱死制动装置(简称ABS)试验台测试参数的要求,在测试系统中需要布置和选择相应的测量传感器,合理选择测量传感器是该试验台研制过程中的一项基本任务。详细阐述试验台使用的五个传感器的选择和计算方法,并根据传感器后接的二次仪表确定测试系统灵敏度。从调试结果可以看出,上述方法是合理的。

  15. Bed dynamics of gas-solid fluidized bed with rod promoter

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The dynamic characteristics of a gas-solid fluidized bed with different rod promoters have been investigated in terms of bed expansion and fluctuation, minimum fluidization velocity and distributor-to-bed pressure drop ratio at minimum fluidization velocity. Experimentation based on statistical design has been carried out and model equations using factorial design of experiments have been developed for the above mentioned quantities for a promoted gas-solid fluidized bed. The model equations have been tested with additional experimental data. The system variables include four types of rod promoters of varying blockage volume, bed particles of four sizes and four initial static bed heights. A comparison between the predicted values of the output variables using the proposed model equation with their corresponding experimental ones shows fairly good agreement.

  16. Design and preliminary test of a fluidised bed photoreactor for ethylene oxidation on mesoporous mixed SiO2/TiO2 nanocomposites under UV-A illumination

    Directory of Open Access Journals (Sweden)

    Maria Lucia V. de Chiara

    2014-12-01

    Full Text Available Ethylene (C2H4 is a plant hormone that has numerous effects on many horticultural and ornamental crops. It accelerates senescence, stimulates chlorophyll loss, enhances excessive softening, promotes discoloration and browning during storage of fresh produce. Among the techniques used to remove or inhibit ethylene action during postharvest handling of fresh products (potassium-based system, high temperature catalytic oxidation, inhibition of ethylene receptors, the use of titanium oxide (TiO2-based materials with photocatalytic activity under ultraviolet (UV light is one of the most promising. A fluidised-bed photoreactor (FBP was designed to decompose ethylene in the storage room atmosphere, and the relative prototype was manufactured. Since TiO2 powder alone is not suitable for use within a fluidised bed, preliminary tests to select the best support were performed. Alumina microspheres showed a good fluidisation behavior; its functionality was tested with different kind of support material and actual photocatalytic activity was tested using SiO2/TiO2-coated alumina microspheres. A reduction of approximately 72% of ethylene concentration in the tested 40 ppm ethylene gas mixture was observed after 4.5 h of 36W UV light exposure. FBP resulted to be suitable to avoid the detrimental presence of C2H4 in the atmosphere surrounding fresh products within cold storage rooms.

  17. Review of acute cancer beds.

    LENUS (Irish Health Repository)

    Evans, D S

    2012-01-01

    A review of admissions to cancer services at University Hospital Galway (UHG) was undertaken to assess the appropriateness of hospital usage. All cancer specialty patients admitted from 26-28 May 2009 were reviewed (n = 82). Chi square tests, Exact tests, and One-way ANOVA were utilised to analyse key issues emerging from the data. Fifty (61%) were classified as emergencies. Twenty three (67%) occupied a designated cancer bed with 24 (30%) in outlying non-oncology wards. The mean length of stay was 29.3 days. Possible alternatives to admission were identified for 15 (19%) patients. There was no evidence of discharge planning for 50 (60%) admissions. There is considerable potential to make more appropriate utilisation of UHG for cancer patients, particularly in terms of reducing bed days and length of stay and the proportion of emergency cancer admissions, and further developing integrated systems of discharge planning.

  18. Review of acute cancer beds.

    LENUS (Irish Health Repository)

    Evans, D S

    2012-01-01

    A review of admissions to cancer services at University Hospital Galway (UHG) was undertaken to assess the appropriateness of hospital usage. All cancer specialty patients admitted from 26-28 May 2009 were reviewed (n = 82). Chi square tests, Exact tests, and One-way ANOVA were utilised to analyse key issues emerging from the data. Fifty (61%) were classified as emergencies. Twenty three (67%) occupied a designated cancer bed with 24 (30%) in outlying non-oncology wards. The mean length of stay was 29.3 days. Possible alternatives to admission were identified for 15 (19%) patients. There was no evidence of discharge planning for 50 (60%) admissions. There is considerable potential to make more appropriate utilisation of UHG for cancer patients, particularly in terms of reducing bed days and length of stay and the proportion of emergency cancer admissions, and further developing integrated systems of discharge planning.

  19. Laboratory Testing of a Fluidized Bed Dry Scrubbing Process for Removal of Sulfur Dioxide and Phosphorous Pentoxide from an Inert Carrier Gas.

    Science.gov (United States)

    1988-03-01

    from vent gas streams in a bench-scale packed bed reactor using quicklime at 135 to 3000C. 4 A 99% HF removal rate was reported at calcium utiliza...Fan et al., "Limestone/Dolomite Sulfation in a Vertical Pneu- matic Transport Reactor ," Ind. Eng. Chem. Process Des. Dev., 23(3), 539-45, 1984. 6. G. A...Vol. II, June 1986. 7. D. Kunni and 0. Levenspiel , Fluidization Engineering, Robert E. % Krieger Publishing Company, Inc., Huntington, N.Y., 1977. 8. R

  20. Fluidized bed calciner apparatus

    Science.gov (United States)

    Owen, Thomas J.; Klem, Jr., Michael J.; Cash, Robert J.

    1988-01-01

    An apparatus for remotely calcining a slurry or solution feed stream of toxic or hazardous material, such as ammonium diurante slurry or uranyl nitrate solution, is disclosed. The calcining apparatus includes a vertical substantially cylindrical inner shell disposed in a vertical substantially cylindrical outer shell, in which inner shell is disposed a fluidized bed comprising the feed stream material to be calcined and spherical beads to aid in heat transfer. Extending through the outer and inner shells is a feed nozzle for delivering feed material or a cleaning chemical to the beads. Disposed in and extending across the lower portion of the inner shell and upstream of the fluidized bed is a support member for supporting the fluidized bed, the support member having uniform slots for directing uniform gas flow to the fluidized bed from a fluidizing gas orifice disposed upstream of the support member. Disposed in the lower portion of the inner shell are a plurality of internal electric resistance heaters for heating the fluidized bed. Disposed circumferentially about the outside length of the inner shell are a plurality of external heaters for heating the inner shell thereby heating the fluidized bed. Further, connected to the internal and external heaters is a means for maintaining the fluidized bed temperature to within plus or minus approximately 25.degree. C. of a predetermined bed temperature. Disposed about the external heaters is the outer shell for providing radiative heat reflection back to the inner shell.

  1. Continuous thorium biosorption--dynamic study for critical bed depth determination in a fixed-bed reactor.

    Science.gov (United States)

    Picardo, Marta Cristina; Ferreira, Ana Cristina de Melo; da Costa, Antonio Carlos Augusto

    2009-01-01

    The objective of the work was to evaluate the biosorption of thorium by the seaweed Sargassum filipendula in a dynamic system. Different bed depths were tested with the purpose of evaluating the critical bed depth for total uptake of the radioactive element. Several bed depths were tested, ranging from 5.0 to 40.0 cm. Bed depths tested presented distinct capacities to accumulate thorium. An increase in biosorption efficiency was observed with an increase in bed depth. The 30.0 cm bed produced an effluent still containing detectable levels of thorium. The critical bed depth suitable for a complete removal of thorium by S.filipendula biomass was equal to 40.0 cm.

  2. Gum-compliant uncertainty propagations for Pu and U concentration measurements using the 1st-prototype XOS/LANL hiRX instrument; an SRNL H-Canyon Test Bed performance evaluation project

    Energy Technology Data Exchange (ETDEWEB)

    Holland, Michael K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); O' Rourke, Patrick E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-05-04

    An SRNL H-Canyon Test Bed performance evaluation project was completed jointly by SRNL and LANL on a prototype monochromatic energy dispersive x-ray fluorescence instrument, the hiRX. A series of uncertainty propagations were generated based upon plutonium and uranium measurements performed using the alpha-prototype hiRX instrument. Data reduction and uncertainty modeling provided in this report were performed by the SRNL authors. Observations and lessons learned from this evaluation were also used to predict the expected uncertainties that should be achievable at multiple plutonium and uranium concentration levels provided instrument hardware and software upgrades being recommended by LANL and SRNL are performed.

  3. Characterization of biofilm in 200W fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Michelle H. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Saurey, Sabrina D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Lee, Brady D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Parker, Kent E. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Eisenhauer, Emalee E. R. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Cordova, Elsa A. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Golovich, Elizabeth C. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States)

    2014-09-29

    Contaminated groundwater beneath the 200 West Area at the Hanford Site in Southeast Washington is currently being treated using a pump and treat system to remove organics, inorganics, radionuclides, and metals. A granular activated carbon-based fluidized bed reactor (FBR) has been added to remove nitrate, hexavalent chromium and carbon tetrachloride. Initial analytical results indicated the microorganisms effectively reduced many of the contaminants to less than cleanup levels. However shortly thereafter operational upsets of the FBR include carbon carry over, over production of microbial extracellular polymeric substance (biofilm) materials, and over production of hydrogen sulfide. As a result detailed investigations were undertaken to understand the functional diversity and activity of the microbial community present in the FBR over time. Molecular analyses including terminal restriction fragment length polymorphism analysis, quantitative polymerase chain reaction and fluorescent in situ hybridization analyses were performed on the microbial community extracted from the biofilm within the bed and from the inoculum, to determine functional dynamics of the FBR bed over time and following operational changes. Findings from these analyses indicated: 1) the microbial community within the bed was completely different than community used for inoculation, and was likely from the groundwater; 2) analyses early in the testing showed an FBR community dominated by a few Curvibacter and Flavobacterium species; 3) the final sample taken indicated that the microbial community in the FBR bed had become more diverse; and 4) qPCR analyses indicated that bacteria involved in nitrogen cycling, including denitrifiers and anaerobic ammonia oxidizing bacteria, were dominant in the bed. These results indicate that molecular tools can be powerful for determining functional diversity within FBR type reactors. Coupled with micronutrient, influent and effluent chemistry

  4. Characterization of Biofilm in 200W Fluidized Bed Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Michelle H.; Saurey, Sabrina D.; Lee, Brady D.; Parker, Kent E.; Eisenhauer, Emalee ER; Cordova, Elsa A.; Golovich, Elizabeth C.

    2014-09-29

    Contaminated groundwater beneath the 200 West Area at the Hanford Site in Southeast Washington is currently being treated using a pump and treat system to remove organics, inorganics, radionuclides, and metals. A granular activated carbon-based fluidized bed reactor (FBR) has been added to remove nitrate, hexavalent chromium and carbon tetrachloride. Initial analytical results indicated the microorganisms effectively reduced many of the contaminants to less than cleanup levels. However shortly thereafter operational upsets of the FBR include carbon carry over, over production of microbial extracellular polymeric substance (biofilm) materials, and over production of hydrogen sulfide. As a result detailed investigations were undertaken to understand the functional diversity and activity of the microbial community present in the FBR over time. Molecular analyses including terminal restriction fragment length polymorphism analysis, quantitative polymerase chain reaction and fluorescent in situ hybridization analyses were performed on the microbial community extracted from the biofilm within the bed and from the inoculum, to determine functional dynamics of the FBR bed over time and following operational changes. Findings from these analyses indicated: 1) the microbial community within the bed was completely different than community used for inoculation, and was likely from the groundwater; 2) analyses early in the testing showed an FBR community dominated by a few Curvibacter and Flavobacterium species; 3) the final sample taken indicated that the microbial community in the FBR bed had become more diverse; and 4) qPCR analyses indicated that bacteria involved in nitrogen cycling, including denitrifiers and anaerobic ammonia oxidizing bacteria, were dominant in the bed. These results indicate that molecular tools can be powerful for determining functional diversity within FBR type reactors. Coupled with micronutrient, influent and effluent chemistry evaluations, a more

  5. Analysis of soil quality test methods for turf bed of golf course%高尔夫球场坪床土壤质量测试指标的分析

    Institute of Scientific and Technical Information of China (English)

    许赛; 宋桂龙

    2013-01-01

    坪床土壤作为球场草坪的基础,对于草坪质量及运动质量都至关重要。目前,国内高尔夫球场坪床土壤质量测试及反馈体系指标不成熟,球场管理者面对球场土壤中出现的一些问题,不能及时、有效的解决,影响球场的管理,也影响高尔夫产业的健康发展。通过对国内外高尔夫球场土壤测试指标状况的分析,提出了一些思考与建议。%As the basis of golf course turfgrass,the turf bed is very important to the turf quality and sports quality.At present,the test methods for soil quality of turf bed and feedback system are more confusing,and there is no mature model.When facing the soil problems,the golf course managers can not solve them timely and effectively,which can affect the golf course management,and also affect the healthy development of golf indus-try.So the comparison and analysis on the test methods were conducted in this paper in order to provide assis-tance.

  6. The Design of Hydraulic Circuit of Hydraulic Steering Gear for Teaching Test-bed%液压舵机教学实验台液压系统的设计

    Institute of Scientific and Technical Information of China (English)

    卢运娇

    2014-01-01

    为了满足教学和相关科研的需要,笔者所在的教学团队设计了一套液压舵机教学实验台,针对实验台中的液压控制部分进行设计,并介绍其工作原理。该系统具有结构简单,造价成本低,运行安全可靠等优点,无论是在教学上还是科研试验中都将起到积极的作用。%The teaching team designed a set of hydraulic steering gear test-bed for teaching and scientific research.Hydraulic circuit is designed for the test-bed and its working principle is introduced .The hydraulic circuit has the advantages of simple structure, low cost, safe and reliable operation and so on.The design for teaching or for related research will play an active role.

  7. Tapered bed bioreactor

    Science.gov (United States)

    Scott, Charles D.; Hancher, Charles W.

    1977-01-01

    A vertically oriented conically shaped column is used as a fluidized bed bioreactor wherein biologically catalyzed reactions are conducted in a continuous manner. The column utilizes a packing material a support having attached thereto a biologically active catalytic material.

  8. Bed Bugs FAQs

    Science.gov (United States)

    ... Bed bugs have been found in five-star hotels and resorts and their presence is not determined ... sleep. These areas include apartments, shelters, rooming houses, hotels, cruise ships, buses, trains, and dorm rooms. They ...

  9. Moving-bed sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Ayala, R.E.; Gupta, R.P.; Chuck, T.

    1995-12-01

    The objective of this program is to develop mixed-metal oxide sorbent formulations that are suitable for moving-bed, high-temperature, desulfurization of coal gas. Work continues on zinc titanates formulations and Z-sorb III sorbent.

  10. Bed Bug Information Clearinghouse

    Science.gov (United States)

    Its purpose is to help states, communities, and consumers in efforts to prevent and control bed bug infestations. Currently includes only reviewed material from federal/state/local government agencies, extension services, and universities.

  11. Bed Bug Tips

    Science.gov (United States)

    How to deal with bed bugs in one printable page. Ten tips include ensuring correct insect identification, reducing clutter, understand integrated pest management, using mattress and box spring encasements, and heat treatment.

  12. Unique Access to Learning

    Science.gov (United States)

    Goble, Don

    2009-01-01

    This article describes the many learning opportunities that broadcast technology students at Ladue Horton Watkins High School in St. Louis, Missouri, experience because of their unique access to technology and methods of learning. Through scaffolding, stepladder techniques, and trial by fire, students learn to produce multiple television programs,…

  13. Alarm pheromones and chemical communication in nymphs of the tropical bed bug Cimex hemipterus (Hemiptera: Cimicidae.

    Directory of Open Access Journals (Sweden)

    H Christoph Liedtke

    Full Text Available The recent resurge of bed bug infestations (Cimex spp.; Cimicidae and their resistance to commonly used pesticides calls for alternative methods of control. Pheromones play an important role in environmentally sustainable methods for the management of many pest insects and may therefore be applicable for the control of bed bugs. The tropical bed bug, Cimex hemipterus, is a temporary ectoparasite on humans and causes severe discomfort. Compared to the common bed bug, Cimex lectularius, little is known about the chemical signalling and pheromone-based behaviour of the tropical species. Here, we show that the antennal morphology and volatile emission of C. hemipterus closely resembles those of C. lectularius and we test their behavioural responses to conspecific odour emissions. Two major volatiles are emitted by male, female and nymph C. hemipterus under stress, (E-2-hexenal and (E-2-octenal. Notably, nymph emissions show contrasting ratios of these compounds to adults and are further characterized by the addition of 4-oxo-(E-2-hexenal and 4-oxo-(E-2-octenal. The discovery of this nymph pheromone in C. hemipterus is potentially the cause of a repellent effect observed in the bio-tests, where nymph odours induce a significantly stronger repellent reaction in conspecifics than adult odours. Our results suggest that pheromone-based pest control methods developed for C. lectularius could be applicable to C. hemipterus, with the unique nymph blend showing promising practical properties.

  14. Alarm pheromones and chemical communication in nymphs of the tropical bed bug Cimex hemipterus (Hemiptera: Cimicidae).

    Science.gov (United States)

    Liedtke, H Christoph; Åbjörnsson, Kajsa; Harraca, Vincent; Knudsen, Jette T; Wallin, Erika A; Hedenström, Erik; Ryne, Camilla

    2011-03-30

    The recent resurge of bed bug infestations (Cimex spp.; Cimicidae) and their resistance to commonly used pesticides calls for alternative methods of control. Pheromones play an important role in environmentally sustainable methods for the management of many pest insects and may therefore be applicable for the control of bed bugs. The tropical bed bug, Cimex hemipterus, is a temporary ectoparasite on humans and causes severe discomfort. Compared to the common bed bug, Cimex lectularius, little is known about the chemical signalling and pheromone-based behaviour of the tropical species. Here, we show that the antennal morphology and volatile emission of C. hemipterus closely resembles those of C. lectularius and we test their behavioural responses to conspecific odour emissions. Two major volatiles are emitted by male, female and nymph C. hemipterus under stress, (E)-2-hexenal and (E)-2-octenal. Notably, nymph emissions show contrasting ratios of these compounds to adults and are further characterized by the addition of 4-oxo-(E)-2-hexenal and 4-oxo-(E)-2-octenal. The discovery of this nymph pheromone in C. hemipterus is potentially the cause of a repellent effect observed in the bio-tests, where nymph odours induce a significantly stronger repellent reaction in conspecifics than adult odours. Our results suggest that pheromone-based pest control methods developed for C. lectularius could be applicable to C. hemipterus, with the unique nymph blend showing promising practical properties.

  15. Design of test-bed for autonomous underwater vehicle%自主式水下航行器试验平台的设计

    Institute of Scientific and Technical Information of China (English)

    张东昆; 侯建钊; 高菲

    2015-01-01

    In order to supply a test⁃bed for the underwater detection,an autonomous underwater vehicle(AUV)was devel⁃oped,which can be applied to the aspects of ocean resource investigation,port security,aquaculture,geomorphology observa⁃tion,etc. With sensors like AHRS and SONAR,It can move and avoid obstacle autonomously,and plan optimal path in real time to realize the underwater geomorphology observation,resource exploration by means of navigation algorithm. It also has the ability to draw maps in unknown underwater environment.%为水下探测提供试验平台,设计了一台自主式水下航行器(AUV)。该航行器可被应用于海洋资源调查、港口安防、水产养殖、地貌观测等诸多方面。它可利用自身搭载的声呐、AHRS等传感器,实现水下自主航行、避障;并通过导航算法,实时地规划最优路径,完成水下地貌观测、资源探测。同时它也具备在水下未知环境,构建地图能力。

  16. 全功率直驱永磁风力发电机组试验台的研究%Research for Full-Power Direct-Drive Permanent Magnet Wind Generator Set Electrical Test-Bed

    Institute of Scientific and Technical Information of China (English)

    罗百敏

    2011-01-01

    直驱型风力发电机组性能优越、运行可靠、维护简便.对采用的低速永磁电机矢量控制调速系统模拟直驱型风机的风轮运行特性进行了理论分析,提出大功率永磁同步发电机组交流传动系统仿真实际直驱永磁风力发电机组的技术方案,并设计和建立全功率直驱永磁风力发电机组的电气试验台.在试验台上对2 MW直驱永磁风力发电机组的电气系统进行了风机功率输出特性和模拟风况的运行性能的试验.%The direct-drive wind generator set has the advantages of superior performance, reliable running and easy maintenance. The theoretical analysis on wind turbine wheel running characteristics of low-speed permanent magnet motor vector control adjustable-speed system simulating direct-drive wind generator used was carried out and technical program of high-power permanent magnet synchronous generator set AC drive system to simulate actual direct-drive permanent magnet wind generator set was proposed, then electrical test bed of full-power direct-drive permanent magnet wind generator set was designed and built. Power output characteristics and running performance simulating wind condition test has been made for electrical system of 2 MW direct-drive permanent magnet wind generator set in test bed.

  17. In Situ Erosion Flume (ISEF): determination of bed-shear stress and erosion of a kaolinite bed

    Science.gov (United States)

    Houwing, Erik-Jan; van Rijn, Leo C.

    1998-06-01

    The strength of a cohesive sediment bed is difficult to determine and must be found experimentally from laboratory tests or through in situ field tests. A new in situ erosion instrument, the In situ Erosion Flume (ISEF), has been developed which is a circulating flow system in the vertical plane. The erosion process of sediment particles of the bed in the test section of the ISEF is related to the prevailing bed-shear stress induced by a unidirectional current. The bed-shear stress can be determined from the measured velocity profile in the test section assuming a logarithmic distribution in a vertical direction. The bed-shear stress equation has been calibrated under various conditions characterised by initiation of motion of sand and gravel particles at a flat bed where the bed-shear stresses mobilising the particles are known from the Shields curve. Three reproducibility tests were carried out under laboratory conditions. The bed consisted of kaolinite and was formed by sedimentation in still fresh water. The results of the three tests showed similar values. The erosion of a kaolinite sediment bed is more precisely determined under laboratory conditions by means of the ISEF. The results are compared with data from the literature. The ISEF is a relatively simple instrument for the determination of the strength of (cohesive) sediment beds. The results based on the ISEF measurements represent the minimum shear stress exerted at initiation of erosion of the bed, which will lead to the maximum shear strength of the top layer of the (cohesive) sediment bed.

  18. Effect of bed particles to combustion of gases in fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Raiko, R.; Wallen, V.; Etelaeaho, R.; Correia, S. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

    1997-10-01

    The objective of this project was to obtain experimental data on effects of sand particles to the combustion of gases. The effect of the surface area of the particles was tested using different sized particles. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 42 mm surrounded by an electric heater. The test rig was built in the Laboratory of Energy and Process Engineering at Tampere University of Technology. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies were conducted with both fresh bed particles and used bed particles. These measurements indicate that carbon monoxide significantly reacts with oxygen in the particulate or emulsion phase of a fluidized bed, if the residence time is long enough. The reaction rate depends mainly on temperature, air coefficient, residence time and particle size of the solids. It seems that the combustion enhances if the average particle size increases. Whether this is caused by increased free path length or reduced specific surface area of the bed is yet unknown. The first might be more probable cause because the majority of reactions often took place in the freeboard right above the bed. It was clear that the bed hindered proper combustion in several cases. (orig.)

  19. NASA's unique networking environment

    Science.gov (United States)

    Johnson, Marjory J.

    1988-01-01

    Networking is an infrastructure technology; it is a tool for NASA to support its space and aeronautics missions. Some of NASA's networking problems are shared by the commercial and/or military communities, and can be solved by working with these communities. However, some of NASA's networking problems are unique and will not be addressed by these other communities. Individual characteristics of NASA's space-mission networking enviroment are examined, the combination of all these characteristics that distinguish NASA's networking systems from either commercial or military systems is explained, and some research areas that are important for NASA to pursue are outlined.

  20. Testing of marrow coal bed systems by hydraulic driving device for thin films of coal; Ensayo de un Sistema de Arranque con Cepillo mediante Accionamiento Hidraulico para Capas Estrechas de CArbon

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This researching project had the aim of: Testing a new mining system performance at narrow coal bed, which uses plough equipment with hydraulic driving devices. Minimising driving power group size to avoid problems regarding with the wall mining-heading transition, decreasing the needed room to house it and thus simplifying wall mining edge support The expected goals were: Take advantage of hydraulic driving devices to obtain a good efficiency with a variable and discontinuous load, bu t without loosing the electric driving devices advantages, consisting on increase driving torque, being the engine blocked Lengthen the mechanical equipment life (chains, driving sprockets, etc.) Reach and economic production rate Researching project was developed in El Bierzo basin (Leon, Spain), in Grupo Ampliacion, a mining group belonged to Viloria Hnos S. A.. (Author)

  1. Bed bug deterrence

    Directory of Open Access Journals (Sweden)

    Haynes Kenneth F

    2010-09-01

    Full Text Available Abstract A recent study in BMC Biology has determined that the immature stage of the bed bug (the nymph signals its reproductive status to adult males using pheromones and thus avoids the trauma associated with copulation in this species. The success of this nymphal strategy of deterrence is instructive. Against the background of increasing problems with bed bugs, this research raises the question whether pheromones might be used to control them. See research article http://www.biomedcentral.com/1741-7007/8/121

  2. in Spouted Bed

    Directory of Open Access Journals (Sweden)

    Bronislaw Buczek

    2013-01-01

    Full Text Available Samples of active coke, fresh and spent after cleaning flue gases from communal waste incinerators, were investigated. The outer layers of both coke particles were separately removed by comminution in a spouted bed. The samples of both active cokes were analysed by means of densities, mercury porosimetry, and adsorption technique. Remaining cores were examined to determine the degree of consumption of coke by the sorption of hazardous emissions (SO2, HCl, and heavy metals through its bed. Differences in contamination levels within the porous structure of the particles were estimated. The study demonstrated the effectiveness of commercial active coke in the cleaning of flue gases.

  3. Development and Testing of the Advanced CHP System Utilizing the Off-Gas from the Innovative Green Coke Calcining Process in Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Chudnovsky, Yaroslav; Kozlov, Aleksandr

    2013-08-15

    Green petroleum coke (GPC) is an oil refining byproduct that can be used directly as a solid fuel or as a feedstock for the production of calcined petroleum coke. GPC contains a high amount of volatiles and sulfur. During the calcination process, the GPC is heated to remove the volatiles and sulfur to produce purified calcined coke, which is used in the production of graphite, electrodes, metal carburizers, and other carbon products. Currently, more than 80% of calcined coke is produced in rotary kilns or rotary hearth furnaces. These technologies provide partial heat utilization of the calcined coke to increase efficiency of the calcination process, but they also share some operating disadvantages. However, coke calcination in an electrothermal fluidized bed (EFB) opens up a number of potential benefits for the production enhancement, while reducing the capital and operating costs. The increased usage of heavy crude oil in recent years has resulted in higher sulfur content in green coke produced by oil refinery process, which requires a significant increase in the calcinations temperature and in residence time. The calorific value of the process off-gas is quite substantial and can be effectively utilized as an “opportunity fuel” for combined heat and power (CHP) production to complement the energy demand. Heat recovered from the product cooling can also contribute to the overall economics of the calcination process. Preliminary estimates indicated the decrease in energy consumption by 35-50% as well as a proportional decrease in greenhouse gas emissions. As such, the efficiency improvement of the coke calcinations systems is attracting close attention of the researchers and engineers throughout the world. The developed technology is intended to accomplish the following objectives: - Reduce the energy and carbon intensity of the calcined coke production process. - Increase utilization of opportunity fuels such as industrial waste off-gas from the novel

  4. The Safety of Hospital Beds

    Science.gov (United States)

    Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

    2015-01-01

    To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

  5. Itegrated Test and Evaluation of a 4-Bed Molecular Sieve (4BMS) Carbon Dioxide Removtal System (CDRA), Mechanical Compressor Engineering Development Unit (EDU), and Sabitier Engineering Development Unit (EDU)

    Science.gov (United States)

    Knox, James C.; Campbell, Melissa; Murdoch, Karen; Miller, Lee A.; Jeng, Frank

    2005-01-01

    Currently on the International Space Station s (ISS) U.S. Segment, carbon dioxide (CO2) scrubbed from the cabin by a 4-Bed Molecular Sieve (4BMS) Carbon Dioxide Removal Assembly (CDRA) is vented overboard as a waste product. Likewise, the product hydrogen (H2) that will be generated by the Oxygen Generation Assembly (OGA) planned for installation will also be vented. A flight experiment has been proposed that will take the waste CO2 removed from the cabin, and via the catalytic Sabatier process, reduce it with waste H2 to generate water and methane. The water produced may provide cost and logistics savings for ISS by reducing the amount of water periodically re-supplied to orbit. To make this concept viable, a mechanical piston compressor and accumulator were developed for collecting and storing the CO2 from the CDRA. The compressor, accumulator and Sabatier system would be packaged together as one unit and referred to as the Carbon Dioxide Reduction Assembly (CRA). Testing was required to evaluate the performance of a 4BMS CDRA, compressor, accumulator, and Sabatier performance along with their operating rules when integrated together. This had been numerically modeled and simulated; however, testing was necessary to verify the results from the engineering analyses. Testing also allowed a better understanding of the practical inefficiencies and control issues involved in a fully integrated system versus the theoretical ideals in the model. This paper presents and discusses the results of an integrated engineering development unit test.

  6. MULTISTAGE FLUIDIZED BED REACTOR

    Science.gov (United States)

    Jonke, A.A.; Graae, J.E.A.; Levitz, N.M.

    1959-11-01

    A multistage fluidized bed reactor is described in which each of a number of stages is arranged with respect to an associated baffle so that a fluidizing gas flows upward and a granular solid downward through the stages and baffles, whereas the granular solid stopsflowing downward when the flow of fluidizing gas is shut off.

  7. Fluidized bed combustion chamber

    Energy Technology Data Exchange (ETDEWEB)

    Kullendorff, A.; Wikner, J.

    1985-03-25

    The chamber is confined in a pressure vessel. The lower part of the chamber has tilted parallel gutters up to the height of the fluidized bed. The slope of the gutter walls is 5 degrees-15 degrees and the top area of the gutters is 1.3 to 3 times larger than their bottom.

  8. Bed Bug Myths

    Science.gov (United States)

    Learn the truth about bed bugs, such as how easy they are to see with the naked eye, their preferred habitat, whether they transmit diseases, their public health effects, and whether pesticides are the best way to deal with an infestation.

  9. Surviving Bed Rest

    Science.gov (United States)

    ... your pregnancy — and your bed rest start a family tree that you can share with your child someday firm up your baby-name choices; use books and websites for ideas organize photo albums read anything — ... people (friends and family) whom you know will probably give gifts build ...

  10. Characterization study and five-cycle tests in a fixed-bed reactor of titania-supported nickel oxide as oxygen carriers for the chemical-looping combustion of methane.

    Science.gov (United States)

    Corbella, Beatriz M; de Diego, Luis F; García-Labiano, Francisco; Adánez, Juan; Palaciost, José M

    2005-08-01

    Recent investigations have shown that in the combustion of carbonaceous compounds CO2 and NOx emissions to the atmosphere can be substantially reduced by using a two stage chemical-looping process. In this process, the reduction stage is undertaken in a first reactor in which the framework oxygen of a reducible inorganic oxide is used, instead of the usual atmospheric oxygen, for the combustion of a carbonaceous compound, for instance, methane. The outlet gas from this reactor is mostly composed of CO2 and steam as reaction products and further separation of these two components can be carried out easily by simple condensation of steam. Then, the oxygen carrier found in a reduced state is transported to a second reactor in which carrier regeneration with air takes place at relatively low temperatures, consequently preventing the formation of thermal NOx. Afterward, the regenerated carrier is carried to the first reactor to reinitiate a new cycle and so on for a number of repetitive cycles, while the carrier is able to withstand the severe chemical and thermal stresses involved in every cycle. In this paper, the performance of titania-supported nickel oxides has been investigated in a fixed-bed reactor as oxygen carriers for chemical-looping combustion of methane. Samples with different nickel oxide contents were prepared by successive incipient wet impregnations, and their performance as oxygen carriers was investigated at 900 degrees C and atmospheric pressure in five-cycle fixed-bed reactor tests using pure methane and pure air for the respective reduction and regeneration stages. The evolution of the outlet gas composition in each stage was followed by gas chromatography, and the involved chemical, structural, and textural changes of the carrier in the reactor bed were studied by using different characterization techniques. From the study, it is deduced that the reactivity of these nickel-based oxygen carriers is in the two involved stages and almost independent

  11. Agglomeration in a fluidized bed using multiple jet streams

    Energy Technology Data Exchange (ETDEWEB)

    Rehmat, A.; Abbasian, J. (Institute of Gas Technology, Chicago, IL (United States)); Kothari, M.; Hariri, H.; Arastoopour, H. (Illinois Inst. of Tech., Chicago, IL (United States))

    1992-01-01

    Tests were conducted to determine the overall temperature distribution, temperature in the vicinity of the jets, and the rate of agglomeration in a fluidized bed containing multiple jet streams. Agglomeration of ash during coal gasification increases carbon utilization efficiency considerably. The agglomeration requires a fluidized-bed reactor with a specially designed distributor equipped with a jet to yield a hot zone confined within the bed. The rate of agglomeration depends upon the size and the intensity of the zone. This rate, and hence the unit capacity, could be increased by adding multiple jets to the distributor. The purpose of this study was to verify this phenomenon. The temperature distribution inside the agglomerating fluidized-bed reactor with a single jet was studied by Hariri et al. Various parameters were involved in agglomeration phenomena -- bed material, fluidization velocity, bed temperature, jet velocity, jet temperature, bed geometry, and distributor geometry. Controlled agglomerates were produced in the fluidized bed when a sloped gas distributor consisting of a central jet and a porous plate was used. Gas at temperatures above the melting temperature of a bed material was introduced into the jet and gas at temperatures below the softening temperature was introduced into the distributor. The rate of agglomerate formation was significantly influenced by an increase in either jet air or auxiliary (grid) air temperature. The extent of agglomeration also depended strongly upon the volume of the hot zone confined within the isotherms with temperatures higher than the melting point of the bed material.

  12. Agglomeration in a fluidized bed using multiple jet streams

    Energy Technology Data Exchange (ETDEWEB)

    Rehmat, A.; Abbasian, J. [Institute of Gas Technology, Chicago, IL (United States); Kothari, M.; Hariri, H.; Arastoopour, H. [Illinois Inst. of Tech., Chicago, IL (United States)

    1992-12-31

    Tests were conducted to determine the overall temperature distribution, temperature in the vicinity of the jets, and the rate of agglomeration in a fluidized bed containing multiple jet streams. Agglomeration of ash during coal gasification increases carbon utilization efficiency considerably. The agglomeration requires a fluidized-bed reactor with a specially designed distributor equipped with a jet to yield a hot zone confined within the bed. The rate of agglomeration depends upon the size and the intensity of the zone. This rate, and hence the unit capacity, could be increased by adding multiple jets to the distributor. The purpose of this study was to verify this phenomenon. The temperature distribution inside the agglomerating fluidized-bed reactor with a single jet was studied by Hariri et al. Various parameters were involved in agglomeration phenomena -- bed material, fluidization velocity, bed temperature, jet velocity, jet temperature, bed geometry, and distributor geometry. Controlled agglomerates were produced in the fluidized bed when a sloped gas distributor consisting of a central jet and a porous plate was used. Gas at temperatures above the melting temperature of a bed material was introduced into the jet and gas at temperatures below the softening temperature was introduced into the distributor. The rate of agglomerate formation was significantly influenced by an increase in either jet air or auxiliary (grid) air temperature. The extent of agglomeration also depended strongly upon the volume of the hot zone confined within the isotherms with temperatures higher than the melting point of the bed material.

  13. Bathing a patient in bed

    Science.gov (United States)

    ... medlineplus.gov/ency/patientinstructions/000427.htm Bathing a patient in bed To use the sharing features on this page, please enable JavaScript. Some patients cannot safely leave their beds to bathe. For ...

  14. VA National Bed Control System

    Data.gov (United States)

    Department of Veterans Affairs — The VA National Bed Control System records the levels of operating, unavailable and authorized beds at each VAMC, and it tracks requests for changes in these levels....

  15. Design and Strength Analysis of Test-bed for Deep-sea Exploration Dipping Winch%深海勘探吊放绞车试验台设计与强度分析

    Institute of Scientific and Technical Information of China (English)

    胡燕平; 吴佳; 郭勇

    2015-01-01

    In order to realize carrying capacity, active heaving and sinking compensation and stopping power of the dipping winch for deep-sea exploration and bearing capacity test of the key parts of the pulley and the cable, a combined winch test-bed based on the counterweight tower and hydraulically driven is designed. Aiming at the geometric structure of test-bed tower, the tower subjected to impact load by winch brake and its constraint condition during the test process are analyzed. Based on ANSYS finite element software, the finite element model of the tower is established. The static analysis of the tower is carried out. The stress and strain distribution of the key parts is gotten. Main structural design improvement project is proposed. The finite element model of the tower and calculation results can provide a theoretical basis for the design and optimization of the same tower.%为了实现深海勘探用吊放绞车承载能力、主动升沉补偿能力、制动能力以及关键部件滑轮和缆索的承载能力测试,设计了一种基于塔式配重和液压驱动的组合型绞车试验台。针对试验台塔架的几何结构,分析了其在试验过程中绞车突然制动所承受的冲击载荷,以及塔架的约束情况。基于 ANSYS 有限元软件,利用梁、壳单元建立塔架有限元模型,对该塔架进行了静态分析,得到了各关键部位的应力、应变分布规律,提出了主要结构设计改进方案。建立的塔架有限元模型以及计算结果能为同类塔架的设计和优化提供理论依据。

  16. Unieke beproevingsinstallatie voor zijdelingse botsproeven met auto's ontwikkeld = Unique testing equipment for sideways-impacts = Einzigartige Testvorrichtung für seitliche Anprall teste für Fahrzeuge.

    NARCIS (Netherlands)

    Schoon, C.C.

    1977-01-01

    The Institute of Road Safety Research SWOV, is investigating the dangers liable to be caused to car occupants in impacts with road furniture. During this research, frontal and sideway-impact tests were made with private cars against lighting columns. Since no suitable equipment existed for carryin

  17. Classification of annular bed flow patterns and investigation on their influence on the bottom spray fluid bed coating process.

    Science.gov (United States)

    Wang, Li Kun; Heng, Paul Wan Sia; Liew, Celine Valeria

    2010-05-01

    This study aims to classify annular bed flow patterns in the bottom spray fluid bed coating process, study their influence on coat uniformity and investigate the feasibility of developing real-time annular bed flow pattern detection as a PAT tool. High-speed imaging and particle image velocimetry were used to visualize annular bed flow. Color coating and subsequent tristimulus colorimetry were employed to determine influence of annular bed flow pattern on coat uniformity. Feasibility of monitoring annular bed flow pattern through an observation window was tested using miniaturized particle velocity field and time series particle velocity orientation information. Three types of annular bed flow patterns were identified. Plug flow gave the best coat uniformity followed by global and localized fluidization. Plug flow may be advantageous for high spray-rate conditions, large-scale coating and prevention of particle segregation. Plug flow could be differentiated from the other flow patterns through a simulated observation window. Annular bed flow patterns were classified and found to influence particle coat uniformity noticeably. Availability of annular bed flow information for large-scale coaters would enable adjustments for process optimization. This study highlights the potential of monitoring annular bed flow pattern as a PAT tool.

  18. Hydrodynamics of multi-phase packed bed micro-reactors

    NARCIS (Netherlands)

    Márquez Luzardo, N.M.

    2010-01-01

    Why to use packed bed micro-reactors for catalyst testing? Miniaturized packed bed reactors have a large surface-to-volume ratio at the reactor and particle level that favors the heat- and mass-transfer processes at all scales (intra-particle, inter-phase and inter-particle or reactor level). If the

  19. Hydrodynamics of multi-phase packed bed micro-reactors

    NARCIS (Netherlands)

    Márquez Luzardo, N.M.

    2010-01-01

    Why to use packed bed micro-reactors for catalyst testing? Miniaturized packed bed reactors have a large surface-to-volume ratio at the reactor and particle level that favors the heat- and mass-transfer processes at all scales (intra-particle, inter-phase and inter-particle or reactor level). If the

  20. A curved flume bed-load experiment

    NARCIS (Netherlands)

    Talmon, A.M.; Marsman, E.R.A.

    1988-01-01

    In this report the results of a bed-load experiment in a curved flume are presented. The experiments have been carried out in the Laboratory of Fluid Mechanics (L.F.M.) at the Delft University of Technology. The main object of the experiments is to develop and to test data-acquisition procedures for

  1. Fluid-Bed Testing of Greatpoint Energy's Direct Oxygen Injection Catalytic Gasification Process for Synthetic Natural Gas and Hydrogen Coproduction Year 6 - Activity 1.14 - Development of a National Center for Hydrogen Technology

    Energy Technology Data Exchange (ETDEWEB)

    Swanson, Michael; Henderson, Ann

    2012-04-01

    near-zero hazardous air or water pollution. This technology would also be conducive to the efficient coproduction of methane and hydrogen while also generating a relatively pure CO{sub 2} stream suitable for enhanced oil recovery (EOR) or sequestration. Specific results of bench-scale testing in the 4- to 38-lb/hr range in the EERC pilot system demonstrated high methane yields approaching 15 mol%, with high hydrogen yields approaching 50%. This was compared to an existing catalytic gasification model developed by GPE for its process. Long-term operation was demonstrated on both Powder River Basin subbituminous coal and on petcoke feedstocks utilizing oxygen injection without creating significant bed agglomeration. Carbon conversion was greater than 80% while operating at temperatures less than 1400°F, even with the shorter-than-desired reactor height. Initial designs for the GPE gasification concept called for a height that could not be accommodated by the EERC pilot facility. More gas-phase residence time should allow the syngas to be converted even more to methane. Another goal of producing significant quantities of highly concentrated catalyzed char for catalyst recovery and material handling studies was also successful. A Pd–Cu membrane was also successfully tested and demonstrated to produce 2.54 lb/day of hydrogen permeate, exceeding the desired hydrogen permeate production rate of 2.0 lb/day while being tested on actual coal-derived syngas that had been cleaned with advanced warm-gas cleanup systems. The membranes did not appear to suffer any performance degradation after exposure to the cleaned, warm syngas over a nominal 100-hour test.

  2. Fluid-Bed Testing of Greatpoint Energy's Direct Oxygen Injection Catalytic Gasification Process for Synthetic Natural Gas and Hydrogen Coproduction Year 6 - Activity 1.14 - Development of a National Center for Hydrogen Technology

    Energy Technology Data Exchange (ETDEWEB)

    Swanson, Michael; Henderson, Ann

    2012-04-01

    near-zero hazardous air or water pollution. This technology would also be conducive to the efficient coproduction of methane and hydrogen while also generating a relatively pure CO{sub 2} stream suitable for enhanced oil recovery (EOR) or sequestration. Specific results of bench-scale testing in the 4- to 38-lb/hr range in the EERC pilot system demonstrated high methane yields approaching 15 mol%, with high hydrogen yields approaching 50%. This was compared to an existing catalytic gasification model developed by GPE for its process. Long-term operation was demonstrated on both Powder River Basin subbituminous coal and on petcoke feedstocks utilizing oxygen injection without creating significant bed agglomeration. Carbon conversion was greater than 80% while operating at temperatures less than 1400°F, even with the shorter-than-desired reactor height. Initial designs for the GPE gasification concept called for a height that could not be accommodated by the EERC pilot facility. More gas-phase residence time should allow the syngas to be converted even more to methane. Another goal of producing significant quantities of highly concentrated catalyzed char for catalyst recovery and material handling studies was also successful. A Pd–Cu membrane was also successfully tested and demonstrated to produce 2.54 lb/day of hydrogen permeate, exceeding the desired hydrogen permeate production rate of 2.0 lb/day while being tested on actual coal-derived syngas that had been cleaned with advanced warm-gas cleanup systems. The membranes did not appear to suffer any performance degradation after exposure to the cleaned, warm syngas over a nominal 100-hour test.

  3. Lake bed classification using acoustic data

    Science.gov (United States)

    Yin, Karen K.; Li, Xing; Bonde, John; Richards, Carl; Cholwek, Gary

    1998-01-01

    As part of our effort to identify the lake bed surficial substrates using remote sensing data, this work designs pattern classifiers by multivariate statistical methods. Probability distribution of the preprocessed acoustic signal is analyzed first. A confidence region approach is then adopted to improve the design of the existing classifier. A technique for further isolation is proposed which minimizes the expected loss from misclassification. The devices constructed are applicable for real-time lake bed categorization. A mimimax approach is suggested to treat more general cases where the a priori probability distribution of the substrate types is unknown. Comparison of the suggested methods with the traditional likelihood ratio tests is discussed.

  4. Geomechanics of bedded salt

    Energy Technology Data Exchange (ETDEWEB)

    Serata, S.; Milnor, S.W.

    1979-06-08

    Creep data from the literature search is reinterpreted by SGI, resulting in a better understanding of the temperature and stress state dependence of the octahedral creep rate and the octahedral shear strength. The concept of a transition strength between the elastic and the plastic states is in agreement with the data. The elastic and rheological properties of salt are described, and a set of constitutive equations is presented. The dependence of material properties on parameters such as temperature is considered. Findings on the permeability of salt are summarized, and the in-situ behavior of openings in bedded salt is described based on extensive engineering experience. A stress measuring system utilizing a finite element computer code is discussed. Geological factors affecting the stability of salt openings are considered, and the Stress Control Technique for designing stable openings in bedded salt formations is explained.

  5. 变速器试验台测控系统的研制%Research and Development of the Measurement and Control System Used for Test Bed of Transmission Boxes

    Institute of Scientific and Technical Information of China (English)

    蒋巍; 石晓辉; 李文礼

    2012-01-01

    In order to adapt to the demands for developing tests of transmission boxes, the structures of hardware and software for a measurement and control system used in test bed of the automobile transmission box is introduced. The system is based on industrial control computer as the core, and developed under the platform of virtual instrument design software LabWindows/CVI. The load spectrum parameters, such as the rotary speed, torque, step of speed, step of torque, duration, as well as the alarm parameters can be compiled. In accordance with these parameters, automatic control and fault alarm for the test procedures are implemented by the system. Various test items of the transmission box can be accomplished for realizing online comprehensive performance test. In practical running, the system features ease operation and maintenance, and high reliability.%为适应变速器试验发展的需求,介绍了一种汽车变速器试验台测控系统的软硬件结构.该系统以工业控制计算机为核心,基于虚拟仪器设计软件LabWindows/CVI开发平台研制,可根据试验需要编制转速、转矩、转速步长、转矩步长、持续时间等载荷谱参数和报警参数.系统按照参数实现试验过程的自动控制和故障报警,可以对变速器进行多种项目的试验,实现了变速器综合性能的在线测试.该系统在实际运行中操作方便、维护简便、可靠性高.

  6. Atmospheric fluidized bed combustion advanced concept system

    Energy Technology Data Exchange (ETDEWEB)

    1992-05-01

    DONLEE Technologies Inc. is developing with support of the US Department of Energy an advanced circulating fluidized bed technology known as the Vortex{trademark} Fluidized Bed Combustor (VFBC). The unique feature of the VFBC is the injection of a significant portion of the combustion air into the cyclone. Since as much as one-half of the total combustion air is injected into the cyclone, the cross-sectional area of the circulating fluidized bed is considerably smaller than typical circulating fluidized beds. The technology is being developed for two applications: Industrial-scale boilers ranging from 20,000 to 100,000 pounds per hour steam generating capacity; and two-stage combustion in which a substoichiometric Vortex Fluidized Bed Combustor (2VFBC) or precombustor is used to generate a combustible gas for use primarily in boiler retrofit applications. This Level II analysis of these two applications indicates that both have merit. An industrial-scale VFBC boiler (60,000 lb/hr of steam) is projected to be economically attractive with coal prices as high as $40 per ton and gas prices between $4 and $5 per thousand cubic feet. The payback time is between 3 and 4 years. The 2VFBC system was evaluated at three capacities of application: 20,000; 60,000 and 100,000 lb/hr of steam. The payback times for these three capacities are 4.5, 2.1 and 1.55 years, respectively. The 2VFBC has potential applications for retrofit of existing pulverized coal-fired boilers or as a new large (utility) boiler. Pressurized operation of the 2VFBC has considerable potential for combined cycle power generation applications. Experimental development of both applications is presented here to demonstrate the potential of these two technologies.

  7. 试验台多通道加载系统的控制方法研究%Research on a Control Method for the Multichannel Force Loading System of Test-Bed

    Institute of Scientific and Technical Information of China (English)

    曾宪忠

    2013-01-01

    试验台多通道加载系统是一种半实物仿真设备,能够在试验室条件下经济、有效地模拟飞机在飞行过程中所受到的舵面气动力矩载荷.通过分析加载系统多余力产生的机理,采用基于结构不变性原理的多余力补偿方法,加载系统可以有效地抑制舵机运动引起的干扰,实现较高的动态加载精度.%Multichannel force loading control system,which could economically and efficaciously simulate the aerodynamic loading of the aircraft,is a very important testing equipment in test-bed.According to the analysis on the cause of the extraneous force,the compensation method based on the structure-invariable principle is used to restrain the influence of the movement of the aircraft actuator,and increase the dynamic precision of the force loading system.

  8. Characterization of the efficiency of the gas-solid contact in circulating bed at by the use of a test reaction: the cumene catalytic cracking

    Energy Technology Data Exchange (ETDEWEB)

    Bayle, J.; Gauthier, T.; Pontier, R. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Briens, C.L.; Bergougnou, M. [University of Western Ontario, London, ON (Canada). Dept. of Physics

    1995-12-31

    The gas-solid down with the stream reactor, the ``downer``, presents a main interest for the high-speed reactions because it is well adapted to hard conditions uses: very short residence times, high temperatures and feeds of catalyst. This reactor type already presents a certain advantage to estimate the charges or new catalysts potential. But, it particularly constitutes an interesting option for some processes as petroleum cuts catalytic cracking. In order to intensify the contact between the catalyst and the reagents, the temperature increase of the reagents has to be almost instantaneous and the initial contact between the gas and the solid particles particularly effective. So as to validate these two hypothesis, the test reaction of the cumene catalytic cracking is carried out in the pilot unit ``downer`` of the Western Ontario University. (O.M.). 11 refs., 3 figs.

  9. Test-bed of a real time detection system for L/H and H/L transitions implemented with the ITMS platform

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz, M. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada, Universidad Politecnica de Madrid (UPM), Crta. Valencia Km-7, Madrid 28031 (Spain); Vega, J. [Asociacion EURATOM/CIEMAT para Fusion, Madrid (Spain); Barrera, E., E-mail: eduardo.barrera@upm.e [Grupo de Investigacion en Instrumentacion y Acustica Aplicada, Universidad Politecnica de Madrid (UPM), Crta. Valencia Km-7, Madrid 28031 (Spain); Gonzalez, J. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada, Universidad Politecnica de Madrid (UPM), Crta. Valencia Km-7, Madrid 28031 (Spain); Murari, A. [Consorzio RFX - Associazione EURATOM ENEA per la Fusione, Padova (Italy); Melendez, R. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada, Universidad Politecnica de Madrid (UPM), Crta. Valencia Km-7, Madrid 28031 (Spain); Ratta, G.; Gonzalez, S. [Asociacion EURATOM/CIEMAT para Fusion, Madrid (Spain)

    2010-07-15

    A basic requirement of the data acquisition systems used in long pulse fusion experiments is to detect events of interest in the acquired signals in real time. Developing such applications is usually a complex task, so it is necessary to develop a set of hardware and software tools that simplify their implementation. An example of these tools is the Intelligent Test and Measurement System (ITMS), which offers distributed data acquisition, distribution and real time processing capabilities with advanced, but easy to use, software tools that simplify application development and system setup. This paper presents the application of the ITMS platform to solve the problem of detecting L/H and H/L transitions in real time based on the use of efficient pattern recognition algorithms.

  10. Elution test in the separation process of zirconium and hafnium with D296 resin in the ion exchange fixed bed%D296树脂分离锆、铪洗脱的效果

    Institute of Scientific and Technical Information of China (English)

    黎志万; 刘锦洪; 刘小龙

    2016-01-01

    This paper introduces the study of elution test in the separation process of zirconium and hafnium with D296 resin in the ion exchange fixed bed.The temperature of the adsorption and elution tests was between 2 and 5 degrees Celsius.Elution tests was carried out in a saturated adsorption ion exchange column,an ion exchange column with exchange region,and an ion exchange column with exchange region and no adsorption region.The results showed that the status of the ion exchange column and the acidity of the eluting agent had a significant effect on the separation effect.When the ion exchange column had exchange region,with the any acidity of sulphuric acid elution,hafnium would be eluted first,but the high acidity of eluent was more favorable for the separation of zirconium and hafnium.When the ion exchange column was saturated adsorption state,with low acidity and high acidity of eluent,zirconium and hafnium could not get effective separation.Experiments proved that, the single fixed bed has low separation efficiency of zirconium and hafnium.In order to achieve separation of zirconium and hafnium,need to design the continuous moving bed separation.%介绍了在离子交换固定床上用D296强碱性阴离子交换树脂分离锆、铪的洗脱实验研究。吸附与洗脱实验的温度均控制在2~5℃,洗脱实验在饱和吸附的离子交换柱、过漏的离子交换柱、未过漏的离子交换柱中进行。研究结果表明:离子交换柱吸附状态以及洗脱剂酸度对分离效果有显著的影响。当离子交换柱存在交换区时,用任何酸度的硫酸作为洗脱剂,铪均被先洗脱出来,但高酸度的洗脱剂对分离锆、铪更有利;当离子交换柱为饱和状态时,低酸度和高酸度的洗脱剂洗脱,锆、铪不能得到分离。实验证明了单一的固定床分离锆、铪的效率低,要成功实现锆、铪的分离,需采用连续分离的离子交换移动床。

  11. Research on the utilization of circulating fluidized bed combustion ashes

    Energy Technology Data Exchange (ETDEWEB)

    Jahn, P.; Weis, P. (EAB Energie-Anlagen Berlin GmbH, Berlin (Germany, F.R.))

    1989-09-01

    Power plant residues from the Moabit, Berlin, Power Plant, which is currently under construction (circulating fluidized bed), must be utilized in accordance with the notice of consent. In order to meet this condition, extensive investigations are being carried out during the design and planning stage. In addition to preliminary tests in a fluidized bed pilot plant, representative circulating fluidized bed ash testing experience has been accumulated in a major test in an operating plant. The paper presents the results of the first physical construction material investigations together with possible solutions for applications at the Berlin West site. 2 refs., 11 figs., 1 tab.

  12. Uniqueness is Important in Competition

    Institute of Scientific and Technical Information of China (English)

    FENG Ai-Xia; XV Xiu-Lian; HE Da-Ren

    2009-01-01

    We propose a quantitative network description on the function of uniqueness in a competition system. Two statistical parameters, competition ability and uniqueness are defined, and their relationship in ordinary cases is analytically discussed. The competition between Chinese regional universities is taken as an example. The empirical investigation results show that the uniqueness of a university is really important in competition. Also,uniqueness is very helpful in the promotion of the university overall quality.

  13. On Uniqueness of coalitional equilibria

    NARCIS (Netherlands)

    Finus, M.; Mouche, van P.H.M.; Rundshagen, B.

    2014-01-01

    For the so-called "new approach" of coalitio formation it is important that coalitional equilibria are unique. Uniqueness comes down to existene and to semi-uniqueness, i.e.\\\\that there exists at most one equilibrium. Although conditions for existence are not problematic, conditions for semi-uniquen

  14. Test-bed of a real time detection system of L/H and H/L transitions implemented with the ITMS platform

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz, M.; Barrera, E.; Gonzalez, J.; Melendez, R. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada - Universidad Politecnica de Madrid (Spain); Vega, J.; Ratta, G.; Gonzalez, S. [Asociacion EURATOM/CIEMAT para Fusion, Madrid (Spain); Murari, A. [Consorzio RFX - Associazione EURATOM ENEA per la Fusione, Padova (Italy)

    2009-07-01

    A basic requirement of the data acquisition systems used in long pulse fusion experiments is to detect events of interest in the acquired signals in real time. Developing such applications is usually a complex task, so it is necessary to develop a set of hardware and software tools that simplify their implementation. An example of these tools is the Intelligent Test and Measurement System (ITMS), which offers distributed data acquisition, distribution and real time processing capabilities with advanced, but easy to use, software tools that simplify application development and system setup. This poster presents the application of the ITMS platform to solve the problem of detecting L/H and H/L transitions in real time based on the use of efficient pattern recognition algorithms. The system architecture used to implement this solution and its performance evaluation are discussed. The system consists of the following elements: a) the ITMS, which is used both to implement the data acquisition and real time LH-HL detection, and to simulate the working environment by reproducing real signals obtained from JET database; b) an event detector, developed using advanced pattern recognition algorithms, that will continuously analyze the information of the acquired signals in order to detect the L/H and H/L transitions; and c) a host computer with several software tools developed with LabVIEW, JAVA and JINI to simplify the development of these complex experiments. These tools allow the user to describe data acquisition and processing tasks using state machines defined in SCXML. These state machines become part of the system setup information, so the behaviour of the system can be changed subsequently by simply modifying these state machines. All the events and key detected are stored by the host computer. This document is a poster. (authors)

  15. Tissue-specific direct microtransfer of nanomaterials into Drosophila embryos as a versatile in vivo test bed for nanomaterial toxicity assessment

    Directory of Open Access Journals (Sweden)

    Vega-Alvarez S

    2014-04-01

    Full Text Available Sasha Vega-Alvarez,1 Adriana Herrera,2 Carlos Rinaldi,2–4 Franklin A Carrero-Martínez1,5 1Department of Biology, 2Department of Chemical Engineering, University of Puerto Rico-Mayagüez, Mayagüez, Puerto Rico; 3J Crayton Pruitt Family Department of Biomedical Engineering, 4Department of Chemical Engineering, University of Florida, Gainesville, FL, USA; 5Department of Anatomy and Neuroscience, University of Puerto Rico, Medical Sciences Campus, San Juan, Puerto Rico Abstract: Nanomaterials are the subject of intense research, focused on their synthesis, modification, and biomedical applications. Increased nanomaterial production and their wide range of applications imply a higher risk of human and environmental exposure. Unfortunately, neither environmental effects nor toxicity of nanomaterials to organisms are fully understood. Cost-effective, rapid toxicity assays requiring minimal amounts of materials are needed to establish both their biomedical potential and environmental safety standards. Drosophila exemplifies an efficient and cost-effective model organism with a vast repertoire of in vivo tools and techniques, all with high-throughput scalability and screening feasibility throughout its life cycle. Here we report tissue specific nanomaterial assessment through direct microtransfer into target tissues. We tested several nanomaterials with potential biomedical applications such as single-wall carbon nanotubes, multiwall carbon nanotubes, silver, gold, titanium dioxide, and iron oxide nanoparticles. Assessment of nanomaterial toxicity was conducted by evaluating progression through developmental morphological milestones in Drosophila. This cost-effective assessment method is amenable to high-throughput screening. Keywords: nanotoxicity, Drosophila, microtransfer, nanoparticle, iron oxide, silver, gold, titanium dioxide, carbon nanotube

  16. Do ants need to estimate the geometrical properties of trail bifurcations to find an efficient route? A swarm robotics test bed.

    Directory of Open Access Journals (Sweden)

    Simon Garnier

    Full Text Available Interactions between individuals and the structure of their environment play a crucial role in shaping self-organized collective behaviors. Recent studies have shown that ants crossing asymmetrical bifurcations in a network of galleries tend to follow the branch that deviates the least from their incoming direction. At the collective level, the combination of this tendency and the pheromone-based recruitment results in a greater likelihood of selecting the shortest path between the colony's nest and a food source in a network containing asymmetrical bifurcations. It was not clear however what the origin of this behavioral bias is. Here we propose that it results from a simple interaction between the behavior of the ants and the geometry of the network, and that it does not require the ability to measure the angle of the bifurcation. We tested this hypothesis using groups of ant-like robots whose perceptual and cognitive abilities can be fully specified. We programmed them only to lay down and follow light trails, avoid obstacles and move according to a correlated random walk, but not to use more sophisticated orientation methods. We recorded the behavior of the robots in networks of galleries presenting either only symmetrical bifurcations or a combination of symmetrical and asymmetrical bifurcations. Individual robots displayed the same pattern of branch choice as individual ants when crossing a bifurcation, suggesting that ants do not actually measure the geometry of the bifurcations when travelling along a pheromone trail. Finally at the collective level, the group of robots was more likely to select one of the possible shorter paths between two designated areas when moving in an asymmetrical network, as observed in ants. This study reveals the importance of the shape of trail networks for foraging in ants and emphasizes the underestimated role of the geometrical properties of transportation networks in general.

  17. Do ants need to estimate the geometrical properties of trail bifurcations to find an efficient route? A swarm robotics test bed.

    Science.gov (United States)

    Garnier, Simon; Combe, Maud; Jost, Christian; Theraulaz, Guy

    2013-01-01

    Interactions between individuals and the structure of their environment play a crucial role in shaping self-organized collective behaviors. Recent studies have shown that ants crossing asymmetrical bifurcations in a network of galleries tend to follow the branch that deviates the least from their incoming direction. At the collective level, the combination of this tendency and the pheromone-based recruitment results in a greater likelihood of selecting the shortest path between the colony's nest and a food source in a network containing asymmetrical bifurcations. It was not clear however what the origin of this behavioral bias is. Here we propose that it results from a simple interaction between the behavior of the ants and the geometry of the network, and that it does not require the ability to measure the angle of the bifurcation. We tested this hypothesis using groups of ant-like robots whose perceptual and cognitive abilities can be fully specified. We programmed them only to lay down and follow light trails, avoid obstacles and move according to a correlated random walk, but not to use more sophisticated orientation methods. We recorded the behavior of the robots in networks of galleries presenting either only symmetrical bifurcations or a combination of symmetrical and asymmetrical bifurcations. Individual robots displayed the same pattern of branch choice as individual ants when crossing a bifurcation, suggesting that ants do not actually measure the geometry of the bifurcations when travelling along a pheromone trail. Finally at the collective level, the group of robots was more likely to select one of the possible shorter paths between two designated areas when moving in an asymmetrical network, as observed in ants. This study reveals the importance of the shape of trail networks for foraging in ants and emphasizes the underestimated role of the geometrical properties of transportation networks in general.

  18. PROOF OF CONCEPT TEST OF A UNIQUE GASEOUS PERFLUROCARBON TRACER SYSTEM FOR VERIFICATION AND LONG TERM MONITORING OF CAPS AND COVER SYSTEMS CONDUCTED AT THE SAVANNAH RIVER SITE BENTONITE MAT TEST FACILITY.

    Energy Technology Data Exchange (ETDEWEB)

    HEISER,J.; SULLIVAN,T.; SERRATO,M.

    2002-02-24

    be used as a non-invasive method (if injection ports are emplaced prior to cover emplacement) on new covers or a minimally invasive method on existing covers. PFT verification will be useful at all buried waste sites using a cover system (e.g., treated or untreated chemical waste landfills) including DOE, commercial, and private sector sites. This paper discusses the initial field trial of the PFT cover monitoring system performed at the Savannah River Site (SRS) in FY01. The experiments provided a successful proof-of-principle test of the PFT technology in monitoring caps and covers. An injection and sampling array was installed in the Bentomat test cap at the SRS Caps Test Facility. This system contained 6 feet of sandy soil beneath a 1/2 inch geosynthetic clay liner covered by an HDPE liner which was covered by 2 feet of clayey top soil. PFTs were injected into the sandy soil though a pre-existing system of access pipes below the cap and soil gas samples were taken on top of the cap. Mid-way into the injection period a series of 1 1/2 inch holes were punched into the cap (through the geomembrane) to provide a positive breach in the cap. Data will be presented that shows the initial cap was fairly tight and leak free and that the artificially induced leaks were detectable within two hours of occurrence.

  19. Bed Rest is an Analog to Study the Physiological Changes of Spaceflight and to Evaluate Countermeasures

    Science.gov (United States)

    Pfannenstiel, P.; Ottenbacher, M.; Inniss, A.; Ware, D.; Anderson, K.; Stranges, S.; Keith, K.; Cromwell, R.; Neigut. J.; Powell, D.

    2012-01-01

    The UTMB/NASA Flight Analog Research Unit is an inpatient unit with a bionutrition kitchen and unique testing areas for studying subjects subjected to 6 degree head-down complete bed rest for prolonged periods as an analog for zero gravity. Bed rest allows study of physiological changes and performance of functional tasks representative of critical interplanetary mission operations and measures of the efficacy of countermeasures designed to protect against the resulting deleterious effects. METHODS/STUDY POPULATION: Subjects are healthy adults 24-55 years old; 60 75 in tall; body mass index 18.5-30; and bone mineral density normal by DXA scan. Over 100 subjects have been studied in 7 campaigns since 2004. The iRAT countermeasure combines high intensity interval aerobic exercises on alternating days with continuous aerobic exercise. Resistance exercise is performed 3 days per week. Subjects are tested on an integrated suite of functional and interdisciplinary physiological tests before and after 70 days of total bed rest. RESULTS/ANTICIPATED RESULTS: It is anticipated that post-bed rest functional performance will be predicted by a weighted combination of sensorimotor, cardiovascular and muscle physiological factors. Control subjects who do not participate in the exercise countermeasure will have significantly greater decreases in these parameters. DISCUSSION/SIGNIFICANCE OF IMPACT: Astronauts experience alterations in multiple physiological systems due to exposure to the microgravity, leading to disruption in the ability to perform functional tasks after reintroduction to a gravitational environment. Current flight exercise countermeasures are not fully protective of cardiovascular, muscle and bone health. There is a need to refine and optimize countermeasures to mitigate health risks associated with long-term space missions.

  20. Measuring bed shear stress along vegetated river beds using FST-hemispheres.

    Science.gov (United States)

    Bockelmann-Evans, B N; Davies, R; Falconer, R A

    2008-09-01

    The measurement of the bed shear stress along vegetated river beds is essential for accurately predicting the water level, velocity and solute and sediment transport fluxes in computational hydroenvironmental models. Details are given herein of an experimental and theoretical study to determine the bed boundary shear stress along vegetated river beds introducing a novel field measuring method, namely the FliessWasserStammtisch (FST)-hemispheres. Although investigations have been conducted previously for sedimentary channels using the FST-hemispheres, this preliminary study is thought to be the first time that such hemispheres have been used to investigate the bed shear stresses in vegetated channels. FST-hemispheres were first developed by Statzner and Müller [1989. Standard hemispheres as indicators of flow characteristics in lotic benthos research. Freshwater Biology 21, 445-459] to act as an integrated indicator of the gross hydrodynamic stresses present near the bed. Test and validation data were found to be at least of the same order of magnitude for the stresses predicted from literature for sedimentary channels, with this study establishing the commencement of a database of calibrated FST-hemisphere laboratory data for vegetated channel beds. In a series of experiments, depths ranging from 0.1 to 0.28 m were considered, equating directly to comparable conditions in small rivers or streams. The results of this study provide a basis for enabling the FST-hemispheres to be used to evaluate the boundary shear stress for a wider range of applications in the future, including vegetated river beds.

  1. In-bed sulphur capture during pressurized fluidized-bed hydroretorting of Eastern oil shales

    Energy Technology Data Exchange (ETDEWEB)

    Abbasian, J.; Rue, D.M.; Lau, F.S. (Institute of Gas Technology, Chicago, IL (USA))

    1991-11-01

    The Institute of Gas Technology is developing a pressurized fluidized-bed hydroretorting (PFH) process for the production of oil from Eastern oil shales. The sulphur present in the Eastern oil shales is converted to H{sub 2}S during hydroretorting. A solid sorbent (limestone or siderite) may be added to the PFH reactor with the oil shale to achieve in-bed desulphurization. The effects of operating conditions on the effectiveness of in-bed sulphur capture with limestone and siderite have been investigated. Reactivities of a limestone and a siderite towards H{sub 2}S were determined in experiments conducted in an ambient pressure thermogravimetric analyser. These tests were conducted in the temperature range of 480-565{degree}C using solid sorbents with an average particle diameter of 0.018 cm ({minus}60{plus}100 mesh). The results of thermogravimetric analysis tests indicate that both limestone and siderite should be capable of capturing a significant fraction of H{sub 2}S removal with in-bed sorbents. The results of these tests confirm that a significant fraction of H{sub 2}S produced in the PFH reactor can be removed with in-bed sorbents. 10 refs., 8 figs., 6 tabs.

  2. Understanding and predicting bed humidity in fluidized bed granulation.

    Science.gov (United States)

    Hu, Xinhui; Cunningham, John; Winstead, Denita

    2008-04-01

    Bed humidity is a critical parameter that needs to be controlled in a fluidized bed granulation to ensure reliability. To predict and control the bed humidity during the fluidized bed granulation process, a simple model based on the mass conservation of moisture was developed. The moisture mass balance model quantitatively simulates the effects of spray rate, binder solution concentration, airflow rate, inlet air temperature, and dew point on the bed humidity. The model was validated by a series of granulations performed in different scale granulators including Glatt GPCG-1, GPCG-15, and GPCG-60. Good agreement was observed between the theoretical prediction and the measured loss on drying (LOD). The model developed in the current work enables us to choose the appropriate parameters for the fluidized bed granulation and can be used as a valuable tool in process scaling-up.

  3. Desipramine and citalopram attenuate pretest swim-induced increases in prodynorphin immunoreactivity in the dorsal bed nucleus of the stria terminalis and the lateral division of the central nucleus of the amygdala in the forced swimming test.

    Science.gov (United States)

    Chung, Sung; Kim, Hee Jeong; Kim, Hyun Ju; Choi, Sun Hye; Cho, Jin Hee; Cho, Yun Ha; Kim, Dong-Hoon; Shin, Kyung Ho

    2014-10-01

    Dynorphin in the nucleus accumbens shell plays an important role in antidepressant-like effect in the forced swimming test (FST), but it is unclear whether desipramine and citalopram treatments alter prodynorphin levels in other brain areas. To explore this possibility, we injected mice with desipramine and citalopram 0.5, 19, and 23 h after a 15-min pretest swim and observed changes in prodynorphin expression before the test swim, which was conducted 24 h after the pretest swim. The pretest swim increased prodynorphin immunoreactivity in the dorsal bed nucleus of the stria terminalis (dBNST) and lateral division of the central nucleus of the amygdala (CeL). This increase in prodynorphin immunoreactivity in the dBNST and CeL was blocked by desipramine and citalopram treatments. Similar changes in prodynorphin mRNA levels were observed in the dBNST and CeL, but these changes did not reach significance. To understand the underlying mechanism, we assessed changes in phosphorylated CREB at Ser(133) (pCREB) immunoreactivity in the dBNST and central nucleus of the amygdala (CeA). Treatment with citalopram but not desipramine after the pretest swim significantly increased pCREB immunoreactivity only in the dBNST. These results suggest that regulation of prodynorphin in the dBNST and CeL before the test swim may be involved in the antidepressant-like effect of desipramine and citalopram in the FST and suggest that changes in pCREB immunoreactivity in these areas may not play an important role in the regulation of prodynorphin in the dBNST and CeA.

  4. Coal Bed Methane Primer

    Energy Technology Data Exchange (ETDEWEB)

    Dan Arthur; Bruce Langhus; Jon Seekins

    2005-05-25

    During the second half of the 1990's Coal Bed Methane (CBM) production increased dramatically nationwide to represent a significant new source of income and natural gas for many independent and established producers. Matching these soaring production rates during this period was a heightened public awareness of environmental concerns. These concerns left unexplained and under-addressed have created a significant growth in public involvement generating literally thousands of unfocused project comments for various regional NEPA efforts resulting in the delayed development of public and fee lands. The accelerating interest in CBM development coupled to the growth in public involvement has prompted the conceptualization of this project for the development of a CBM Primer. The Primer is designed to serve as a summary document, which introduces and encapsulates information pertinent to the development of Coal Bed Methane (CBM), including focused discussions of coal deposits, methane as a natural formed gas, split mineral estates, development techniques, operational issues, producing methods, applicable regulatory frameworks, land and resource management, mitigation measures, preparation of project plans, data availability, Indian Trust issues and relevant environmental technologies. An important aspect of gaining access to federal, state, tribal, or fee lands involves education of a broad array of stakeholders, including land and mineral owners, regulators, conservationists, tribal governments, special interest groups, and numerous others that could be impacted by the development of coal bed methane. Perhaps the most crucial aspect of successfully developing CBM resources is stakeholder education. Currently, an inconsistent picture of CBM exists. There is a significant lack of understanding on the parts of nearly all stakeholders, including industry, government, special interest groups, and land owners. It is envisioned the Primer would being used by a variety of

  5. Bed Rest Muscular Atrophy

    Science.gov (United States)

    Greenleaf, John E.

    2000-01-01

    A major debilitating response from prolonged bed rest (BR) is muscle atrophy, defined as a "decrease in size of a part of tissue after full development has been attained: a wasting away of tissue as from disuse, old age, injury or disease". Part of the complicated mechanism for the dizziness, increased body instability, and exaggerated gait in patients who arise immediately after BR may be a result of not only foot pain, but also of muscular atrophy and associated reduction in lower limb strength. Also, there seems to be a close association between muscle atrophy and bone atrophy. A discussion of many facets of the total BR homeostatic syndrome has been published. The old adage that use determines form which promotes function of bone (Wolff's law) also applies to those people exposed to prolonged BR (without exercise training) in whom muscle atrophy is a consistent finding. An extreme case involved a 16-year-old boy who was ordered to bed by his mother in 1932: after 50 years in bed he had "a lily-white frame with limbs as thin as the legs of a ladder-back chair". These findings emphasize the close relationship between muscle atrophy and bone atrophy. In addition to loss of muscle mass during deconditioning, there is a significant loss of muscle strength and a decrease in protein synthesis. Because the decreases in force (strength) are proportionately greater than those in fiber size or muscle cross-sectional area, other contributory factors must be involved; muscle fiber dehydration may be important.

  6. Bed Rest Muscular Atrophy

    Science.gov (United States)

    Greenleaf, John E.

    2000-01-01

    A major debilitating response from prolonged bed rest (BR) is muscle atrophy, defined as a "decrease in size of a part of tissue after full development has been attained: a wasting away of tissue as from disuse, old age, injury or disease". Part of the complicated mechanism for the dizziness, increased body instability, and exaggerated gait in patients who arise immediately after BR may be a result of not only foot pain, but also of muscular atrophy and associated reduction in lower limb strength. Also, there seems to be a close association between muscle atrophy and bone atrophy. A discussion of many facets of the total BR homeostatic syndrome has been published. The old adage that use determines form which promotes function of bone (Wolff's law) also applies to those people exposed to prolonged BR (without exercise training) in whom muscle atrophy is a consistent finding. An extreme case involved a 16-year-old boy who was ordered to bed by his mother in 1932: after 50 years in bed he had "a lily-white frame with limbs as thin as the legs of a ladder-back chair". These findings emphasize the close relationship between muscle atrophy and bone atrophy. In addition to loss of muscle mass during deconditioning, there is a significant loss of muscle strength and a decrease in protein synthesis. Because the decreases in force (strength) are proportionately greater than those in fiber size or muscle cross-sectional area, other contributory factors must be involved; muscle fiber dehydration may be important.

  7. Students Discover Unique Planet

    Science.gov (United States)

    2008-12-01

    Three undergraduate students, from Leiden University in the Netherlands, have discovered an extrasolar planet. The extraordinary find, which turned up during their research project, is about five times as massive as Jupiter. This is also the first planet discovered orbiting a fast-rotating hot star. Omega Centauri ESO PR Photo 45a/08 A planet around a hot star The students were testing a method of investigating the light fluctuations of thousands of stars in the OGLE database in an automated way. The brightness of one of the stars was found to decrease for two hours every 2.5 days by about one percent. Follow-up observations, taken with ESO's Very Large Telescope in Chile, confirmed that this phenomenon is caused by a planet passing in front of the star, blocking part of the starlight at regular intervals. According to Ignas Snellen, supervisor of the research project, the discovery was a complete surprise. "The project was actually meant to teach the students how to develop search algorithms. But they did so well that there was time to test their algorithm on a so far unexplored database. At some point they came into my office and showed me this light curve. I was completely taken aback!" The students, Meta de Hoon, Remco van der Burg, and Francis Vuijsje, are very enthusiastic. "It is exciting not just to find a planet, but to find one as unusual as this one; it turns out to be the first planet discovered around a fast rotating star, and it's also the hottest star found with a planet," says Meta. "The computer needed more than a thousand hours to do all the calculations," continues Remco. The planet is given the prosaic name OGLE2-TR-L9b. "But amongst ourselves we call it ReMeFra-1, after Remco, Meta, and myself," says Francis. The planet was discovered by looking at the brightness variations of about 15 700 stars, which had been observed by the OGLE survey once or twice per night for about four years between 1997 and 2000. Because the data had been made public

  8. Pulsed atmospheric fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    1989-11-01

    In order to verify the technical feasibility of the MTCI Pulsed Atmospheric Fluidized Bed Combustor technology, a laboratory-scale system was designed, built and tested. Important aspects of the operational and performance parameters of the system were established experimentally. A considerable amount of the effort was invested in the initial task of constructing an AFBC that would represent a reasonable baseline against which the performance of the PAFBC could be compared. A summary comparison of the performance and emissions data from the MTCI 2 ft {times} 2 ft facility (AFBC and PAFBC modes) with those from conventional BFBC (taller freeboard and recycle operation) and circulating fluidized bed combustion (CFBC) units is given in Table ES-1. The comparison is for typical high-volatile bituminous coals and sorbents of average reactivity. The values indicated for BFBC and CFBC were based on published information. The AFBC unit that was designed to act as a baseline for the comparison was indeed representative of the larger units even at the smaller scale for which it was designed. The PAFBC mode exhibited superior performance in relation to the AFBC mode. The higher combustion efficiency translates into reduced coal consumption and lower system operating cost; the improvement in sulfur capture implies less sorbent requirement and waste generation and in turn lower operating cost; lower NO{sub x} and CO emissions mean ease of site permitting; and greater steam-generation rate translates into less heat exchange surface area and reduced capital cost. Also, the PAFBC performance generally surpasses those of conventional BFBC, is comparable to CFBC in combustion and NO{sub x} emissions, and is better than CFBC in sulfur capture and CO emissions even at the scaled-down size used for the experimental feasibility tests.

  9. Biparticle fluidized bed reactor

    Science.gov (United States)

    Scott, C.D.

    1993-12-14

    A fluidized bed reactor system which utilizes a fluid phase, a retained fluidized primary particulate phase, and a migratory second particulate phase is described. The primary particulate phase is a particle such as a gel bead containing an immobilized biocatalyst. The secondary particulate phase, continuously introduced and removed in either cocurrent or countercurrent mode, acts in a secondary role such as a sorbent to continuously remove a product or by-product constituent from the fluid phase. Introduction and removal of the sorbent phase is accomplished through the use of feed screw mechanisms and multivane slurry valves. 3 figures.

  10. A DU bed system for storing and supplying hydrogen isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Koo, Daeseo; Park, Jongchul; Ahn, Do-Hee; Chung, Hongsuk [KAERI, Daejeon (Korea, Republic of); Yun, Sei-Hun [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Depleted uranium (DU) has been extensively proposed for the storage, supply, and recovery of hydrogen isotopes. SDS is used for storing hydrogen isotopes as a metal hydride form. To control the SDS, it is necessary to monitor the tritium amount in a bed. In this study, a full-sized DU bed was designed and fabricated including cylindrical-type copper foam of nine layers to study the characteristics of hydriding/dehydriding and simulate the tritium amount in a bed. The integrity and leak inspection on the welding of a primary vessel was performed using a penetration test, helium leak test, and pressure test. Auto tuning on the cable heaters of two pairs in the DU bed was also be performed. In our next study, the hydriding/dehydriding on a DU bed will be performed. A simulation on the depleted uranium hydriding will be carried out. A DU bed was designed and fabricated including cylindrical-type copper foam of nine layers to study the characteristics of hydriding/dehydriding and simulate the tritium amount in a bed. Through a penetration test, it was confirmed that the welding of the primary vessel has a good integrity. It was confirmed that the two helium tubes is sound by inspecting a helium leak test on the welding of the primary vessel. It was also confirmed that the primary vessel has a good integrity by inspecting a helium leak and conducting a pressure test on it. Vacuuming of the DU bed system was carried out. Vacuuming of the in-bed calorimetric equipment was also carried out.

  11. Exercise countermeasures for bed-rest deconditioning

    Science.gov (United States)

    Greenleaf, John (Editor)

    1993-01-01

    The purpose for this 30-day bed rest study was to investigate the effects of short-term, high intensity isotonic and isokinetic exercise training on maintenance of working capacity (peak oxygen uptake), muscular strength and endurance, and on orthostatic tolerance, posture and gait. Other data were collected on muscle atrophy, bone mineralization and density, endocrine analyses concerning vasoactivity and fluid-electrolyte balance, muscle intermediary metabolism, and on performance and mood of the subjects. It was concluded that: The subjects maintained a relatively stable mood, high morale, and high esprit de corps throughout the study. Performance improved in nearly all tests in almost all the subjects. Isotonic training, as opposed to isokinetic exercise training, was associated more with decreasing levels of psychological tension, concentration, and motivation; and improvement in the quality of sleep. Working capacity (peak oxygen uptake) was maintained during bed rest with isotonic exercise training; it was not maintained with isokinetic or no exercise training. In general, there was no significant decrease in strength or endurance of arm or leg muscles during bed rest, in spite of some reduction in muscle size (atrophy) of some leg muscles. There was no effect of isotonic exercise training on orthostasis, since tilt-table tolerance was reduced similarly in all three groups following bed rest. Bed rest resulted in significant decreases of postural stability and self-selected step length, stride length, and walking velocity, which were not influenced by either exercise training regimen. Most pre-bed rest responses were restored by the fourth day of recovery.

  12. Effects of ultralow oxygen and vacuum treatments on bed bug (Heteroptera: Cimicidae) survival

    Science.gov (United States)

    Control of bed bugs has always been problematic, balancing among efficacy, safety, and cost. In this study, ultralow oxygen (ULO) and vacuum treatments were tested on bed bugs to develop a safer, effective, and environmental friendly solution to bed bug infestations. ULO treatments were establishe...

  13. Purification performances of common reed beds based on the ...

    African Journals Online (AJOL)

    SARAH

    2013-11-30

    Nov 30, 2013 ... wastewater treatment facilities must be built immediately. .... wastewater from the second septic tank was used to test the reed bed's ... The small treatment plant was built ..... constructed wetlands systems for wastewater.

  14. Purification performances of common reed beds based on the ...

    African Journals Online (AJOL)

    ... performances of common reed beds in order to facilitate their implementation in Benin. Methodology and Results: A test station, which utilizes vertical flow filters ... at 5 days of incubation (BOD5), Total Suspended Solid (TSS), Total Kjeldahl ...

  15. Do the coarsest bed fractions and stream power record contemporary trends in steep headwater channels?

    Science.gov (United States)

    Galia, Tomáš; Škarpich, Václav

    2016-11-01

    Three stream channels that were devoid of evidence of past debris flows and one headwater channel that contained debris flow deposits in the flysch western Carpathians, Czech Republic were selected to test relationships between in-channel processes, bed sediments, and unit stream power calculated for bankfull and Q20 flows. Contemporary depositional or erosional trends in the examined headwaters were linked with bed sediments that were represented by the coarsest cobble and boulder fraction with a mean calculated from the five largest particles. The downstream trends of the unit stream power were derived for a bankfull discharge and a well-documented 20-year flood event. In addition, the flow competences during the discharges were calculated using indirect bedload transport measurements. Downstream fining of the cobble and boulder fraction was observed in all of the studied headwaters, and unique downstream variations of the unit stream power were calculated for the longitudinal profiles. The single-thread streams that were devoid of evidence of debris flow events exhibited direct relations between the coarsest sediment size and the unit stream power, especially as calculated for the 20-year flood event and for erosional/depositional trends of the channel. The downstream coarsening of the bed material that was accompanied by an increase in the unit stream power was usually observed in the case of deeply incised (> 0.5 m above the assumed bankfull depth) channel reaches. The calculated competence of the 20-year flow was up to twofold higher than that required to entrain the largest bed particle diameters in those channel reaches, and even the bankfull flow was potentially capable of transporting the coarsest bed particles in certain of the reaches. On the other hand, some depositional channel reaches evidently led to the disconnectivity of transport of the coarsest bed material even in the case of the 20-year flood event. The longitudinal profile of the channel that

  16. AN EXPERIMENT TO STUDY PEBBLE BED LIQUID-FLUORIDE-SALT HEAT TRANSFER

    Energy Technology Data Exchange (ETDEWEB)

    Yoder Jr, Graydon L [ORNL; Aaron, Adam M [ORNL; Heatherly, Dennis Wayne [ORNL; Holcomb, David Eugene [ORNL; Kisner, Roger A [ORNL; McCarthy, Mike [ORNL; Peretz, Fred J [ORNL; Wilgen, John B [ORNL; Wilson, Dane F [ORNL

    2011-01-01

    A forced-convection liquid-fluoride-salt loop is being constructed at Oak Ridge National Laboratory (ORNL). This loop was designed as a versatile experimental facility capable of supporting general thermal/fluid/corrosion testing of liquid fluoride salts. The initial test configuration is designed to support the Pebble Bed Advanced High-Temperature Reactor and incorporates a test section designed to examine the heat transfer behavior of FLiNaK salt in a heated pebble bed. The loop is constructed of Inconel 600 and is capable of operating at up to 700oC. It contains a total of 72 kg of FLiNaK salt and uses an overhung impeller centrifugal sump pump that can provide FLiNaK flow at 4.5 kg/s with a head of 0.125 MPa. The test section is made of silicon carbide (SiC) and contains approximately 600 graphite spheres, 3 cm in diameter. The pebble bed is heated using a unique inductive technique. A forced induction air cooler removes the heat added to the pebble bed. The salt level within the loop is maintained by controlling an argon cover gas pressure. Salt purification is performed in batch mode by transferring the salt from the loop into a specially made nickel crucible system designed to remove oxygen, moisture and other salt impurities. Materials selection for the loop and test section material was informed by 3 months of Inconel 600 and SiC corrosion testing as well as tests examining subcomponent performance in the salt. Several SiC-to-Inconel 600 mechanical joint designs were considered before final salt and gas seals were chosen. Structural calculations of the SiC test section were performed to arrive at a satisfactory test section configuration. Several pump vendors provided potential loop pump designs; however, because of cost, the pump was designed and fabricated in-house. The pump includes a commercial rotating dry gas shaft seal to maintain loop cover gas inventory. The primary instrumentation on the loop includes temperature, pressure, and loop flow rate

  17. A Spouted Bed Reactor Monitoring System for Particulate Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    D. S. Wendt; R. L. Bewley; W. E. Windes

    2007-06-01

    operating temperature data from the spouted bed monitoring system are used to determine the bed operating regime and monitor the particle characteristics. Tests have been conducted to determine the sensitivity of the monitoring system to the different operating regimes of the spouted particle bed. The pressure transducer signal response was monitored over a range of particle sizes and gas flow rates while holding bed height constant. During initial testing, the bed monitoring system successfully identified the spouting regime as well as when particles became interlocked and spouting ceased. The particle characterization capabilities of the bed monitoring system are currently being tested and refined. A feedback control module for the bed monitoring system is currently under development. The feedback control module will correlate changes in the bed response to changes in the particle characteristics and bed spouting regime resulting from the coating and/or conversion process. The feedback control module will then adjust the gas composition, gas flow rate, and run duration accordingly to maintain the bed in the desired spouting regime and produce optimally coated/converted particles.

  18. Nucla circulating atmospheric fluidized bed demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-31

    During the fourth quarter of 1990, steady-state performance testing at the Nucla Circulating Fluidized Bed (CFB) resumed under sponsorship of the US Department of Energy. Co-sponsorship of the Demonstration Test Program by the Electric Power Research Institute (EPRI) was completed on June 15, 1990. From October through December, 1990, Colorado-Ute Electric Association (CUEA) completed a total of 23 steady-state performance tests, 4 dynamic tests, and set operating records during November and December as the result of improved unit operating reliability. Highlight events and achievements during this period of operation are presented.

  19. GREENHOUSE GAS EMISSIONS CONTROL BY OXYGEN FIRING IN CIRCULATING FLUIDIZED BED BOILERS: PHASE II--PILOT SCALE TESTING AND UPDATED PERFORMANCE AND ECONOMICS FOR OXYGEN FIRED CFB WITH CO2 CAPTURE

    Energy Technology Data Exchange (ETDEWEB)

    Nsakala ya Nsakala; Gregory N. Liljedahl; David G. Turek

    2004-10-27

    Because fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic CO{sub 2} emissions. In this Phase II study, ALSTOM Power Inc. (ALSTOM) has investigated one promising near-term coal fired power plant configuration designed to capture CO{sub 2} from effluent gas streams for sequestration. Burning fossil fuels in mixtures of oxygen and recirculated flue gas (made principally of CO{sub 2}) essentially eliminates the presence of atmospheric nitrogen in the flue gas. The resulting flue gas is comprised primarily of CO{sub 2}, along with some moisture, nitrogen, oxygen, and trace gases like SO{sub 2} and NO{sub x}. Oxygen firing in utility scale Pulverized Coal (PC) fired boilers has been shown to be a more economical method for CO{sub 2} capture than amine scrubbing (Bozzuto, et al., 2001). Additionally, oxygen firing in Circulating Fluid Bed Boilers (CFB's) can be more economical than in PC or Stoker firing, because recirculated gas flow can be reduced significantly. Oxygen-fired PC and Stoker units require large quantities of recirculated flue gas to maintain acceptable furnace temperatures. Oxygen-fired CFB units, on the other hand, can accomplish this by additional cooling of recirculated solids. The reduced recirculated gas flow with CFB plants results in significant Boiler Island cost savings resulting from reduced component The overall objective of the Phase II workscope, which is the subject of this report, is to generate a refined technical and economic evaluation of the Oxygen fired CFB case (Case-2 from Phase I) utilizing the information learned from pilot-scale testing of this concept. The objective of the pilot-scale testing was to generate detailed technical data needed to establish advanced CFB design requirements and performance when firing coals and

  20. Numerical simulation of nuclear pebble bed configurations

    Energy Technology Data Exchange (ETDEWEB)

    Shams, A., E-mail: shams@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Roelofs, F., E-mail: roelofs@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Komen, E.M.J., E-mail: komen@nrg.eu [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands); Baglietto, E., E-mail: emiliob@MIT.EDU [Massachusetts Institute of Technology (MIT) (United States)

    2015-08-15

    Highlights: • Numerical simulations of a single face cubic centred pebble bed are performed. • Wide range of turbulence modelling techniques are used to perform these calculations. • The methods include 1-DNS, 1-LES, 3-Hybrid (RANS/LES) and 3-RANS models, respectively. • The obtained results are extensively compared to provide guidelines for such flow regimes. • These guidelines are used to perform reference LES for a limited sized random pebble bed. - Abstract: High Temperature Reactors (HTRs) are being considered all over the world. An HTR uses helium gas as a coolant, while the moderator function is taken up by graphite. The fuel is embedded in the graphite moderator. A particular inherent safety advantage of HTR designs is that the graphite can withstand very high temperatures, that the fuel inside will stay inside the graphite pebble and cannot escape to the surroundings even in the event of loss of cooling. Generally, the core can be designed using a graphite pebble bed. Some experimental and demonstration reactors have been operated using a pebble bed design. The test reactors have shown safe and efficient operation, however questions have been raised about possible occurrence of local hot spots in the pebble bed which may affect the pebble integrity. Analysis of the fuel integrity requires detailed evaluation of local heat transport phenomena in a pebble bed, and since such phenomena cannot easily be modelled experimentally, numerical simulations are a useful tool. As a part of a European project, named Thermal Hydraulics of Innovative Nuclear Systems (THINS), a benchmarking quasi-direct numerical simulation (q-DNS) of a well-defined pebble bed configuration has been performed. This q-DNS will serve as a reference database in order to evaluate the prediction capabilities of different turbulence modelling approaches. A wide range of numerical simulations based on different available turbulence modelling approaches are performed and compared with

  1. Architecture for a Distributed Integrated Test Bed

    Science.gov (United States)

    2009-10-01

    paper, we summarize the results of a large combined study of the German government, industry and research institutes that addresses the architectural...architecture, but also of a project called 2 CPM: Costumer Product Management (the procurement process of...4 A FOM in the case of HLA. 5 In the current VIntEL experimentation, we use a VIntEL FOM, which is an extension of

  2. TActical Sensor network TEst bed (TASTE)

    NARCIS (Netherlands)

    Dorp, P. van; Bekman, H.H.P.T.; Sandbrink, R.D.J.

    2008-01-01

    TASTE is a software tool for specifying and deploying unattended ground sensors (UGS) in a composition which the commander assumes will suit his needs the best. With TASTE different sensor types such as acoustic, magnetic, seismic, radar and IR imaging sensors can be deployed virtually and their

  3. Wireless Sensor Networks TestBed: ASNTbed

    CSIR Research Space (South Africa)

    Dludla, AG

    2013-05-01

    Full Text Available Wireless sensor networks (WSNs) have been used in different types of applications and deployed within various environments. Simulation tools are essential for studying WSNs, especially for exploring large-scale networks. However, WSN testbeds...

  4. Airborne Optical Systems Test Bed (AOSTB)

    Science.gov (United States)

    2016-07-01

    modified as needed. • Leverage existing software data processing chain with minor modifications for variations in data formatting . • Collect...the task of improving the nation’s air defense system. The Air Force, in turn, reached out to MIT for assistance, which led to the formation of MIT...desiccant, in order to control the dew point inside the enclosures. The optical design can be seen below in Figure 9. Figure 9 - Optical Layout

  5. Ultrasonic Test Bed for Quantitative NDE

    Science.gov (United States)

    1982-07-01

    contact: P.H. Milham Director of Contracts and Pricing Rockwell International Science Center 1049 Camino Dos Rios Thousand Oaks, CA 91360 PH (805) 498...50I rb ) CAI COAV DLY Z04 70 25,L5253 *i6 v 1. -- i~r~vYS - C eW 2 ro 2l C U9 4 v ~ eelr 75(4.59 D 1 4r /, 0 DATO (.1e - rvecfoz 30 7V C- i

  6. TActical Sensor network TEst bed (TASTE)

    NARCIS (Netherlands)

    Dorp, P. van; Bekman, H.H.P.T.; Sandbrink, R.D.J.

    2008-01-01

    TASTE is a software tool for specifying and deploying unattended ground sensors (UGS) in a composition which the commander assumes will suit his needs the best. With TASTE different sensor types such as acoustic, magnetic, seismic, radar and IR imaging sensors can be deployed virtually and their ind

  7. Stormwater and Wastewater Infrastructure Monitoring Test Bed

    Science.gov (United States)

    The growing application of stormwater and wastewater management in urban and urbanizing environments is increasing the demand for monitoring technologies and systems that can provide reliable performance data, in real-time or near real-time, for operation and maintenance decision...

  8. Titan Montgolfiere Terrestrial Test Bed Project

    Data.gov (United States)

    National Aeronautics and Space Administration — With the Titan Saturn System Mission, NASA is proposing to send a Montgolfiere balloon to probe the atmosphere of Titan. To better plan this mission and create a...

  9. Titan Montgolfiere Terrestrial Test Bed Project

    Data.gov (United States)

    National Aeronautics and Space Administration — With the Titan Saturn System Mission, NASA is proposing to send a Montgolfiere balloon to probe the atmosphere of Titan. In order to better plan this mission and...

  10. Development of a new method for improving load turndown in fluidized bed combustors: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brown, R.C.

    1988-12-01

    The objective of this research was to investigate a new concept in fluidized bed design that improves load turndown capability. This improvement is accomplished by independently controlling heat transfer and combustion in the combustor. The design consists of two fluidized beds, one central and one annular. The central bed serves as the combustion bed. The annular bed is fluidized separately from the combustion bed and its level of fluidization determine the overall heat transfer rate from the combustion bed to the surrounding water jacket. Early theoretical considerations suggested a load turndown exceeding ten was possible for this design. This research consisted of three major phases: development of a computational model to predict heat transfer in the two-bed combustor, heat transfer measurements in hot-and-cold flow models of the combustor, and combustion tests in an optimally designed combustor. The computation model was useful in selecting the design of the combustor. Annular bed width and particle sizes were chosen with the aid of the model. The heat transfer tests were performed to determine if the existing correlations for fluidized bed heat transfer coefficients were sufficiently accurate for high aspect ratio fluidized beds (such as the annular bed in the combustor). Combustion tests were performed in an optimally designed combustor. Three fuel forms were used: double screened, crushed coal, coal-water-limestone mixtures (CWLM), and coal-limestone briquettes. 18 refs., 30 figs., 8 tabs.

  11. New Developments in Spinning Fluidised Bed Incineration Technology

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    At the present time, the sewage treatment plants in the UK produce about 25 million tons of sewage sludge each year at a concentration of 4% solids. New regulations forbid sea dumping and in the near future new incinerators will be required to dispose of about 5 million tons per year. Bubbling fluidised bed incinerators are widely used to burn sewage sludge at a typical consumption rate of about 0.02kg(dry)·s-1·m2, and it follows that over 300 conventional fluidised bed incinerators of 3m diameter could be required to cope with the increased demand.At Sheffield University Waste Incineration Centre (SUWIC) research work is being carried out to develop a novel spinning fluidised bed incinerator. The key factor to note is that when air flows up through a bed of near mono-sized particles, it fluidises when the pressure drop across the bed is equal to the weight of the bed. Normally, the weight of the bed is determined by gravity. However, if the bed is contained by a cylindrical air distributor 'plate' that is rotating rapidly about its axis, then the effective weight of the bed can be increased dramatically. The airflow passing through the bed can be increased proportionally to the "g" level produced by the rotation and it follows that the process has been intensified. In exploratory tests with a spinning fluidised bed we have achieved combustion intensities with coal combustion as high as 100MW/m3. A problem with burning coal is that it was difficult to remove the heat and rotating water seals had to be used to transfer cooling water into the bed. In the case of sewage and other sludges, this problem does not exist since the flue gases can remove the small amount of heat released. The rotating fluidised bed sludge incinerator is a novel device, which is very compact. It is able to solve the turndown problem encountered with conventional fluidised beds by simply changing the rotation speed. Bearing in mind that a centrifugal sludge de-watering unit is already used

  12. Behavioral responses of the bed bug to insecticide residues.

    Science.gov (United States)

    Romero, Alvaro; Potter, Michael F; Haynes, Kenneth F

    2009-01-01

    The recent resurgence of bed bugs, Cimex lectularius L. (Heteroptera: Cimicidae), has increased the demand for information about effective control tactics. Several studies have focused on determining the susceptibility of bed bug populations to insecticides. However, behavioral responses of bed bugs to insecticide residues could influence their efficacy. The behavioral responses of bed bugs to deltamethrin and chlorfenapyr, two commonly used insecticides for bed bug control in the United States, were evaluated. In two-choice tests, grouped insects and individual insects avoided resting on filter paper treated with deltamethrin. Insects did not avoid surfaces treated with chlorfenapyr. Harborages, containing feces and eggs and treated with a deltamethrin-based product, remained attractive to individuals from a strain resistant to pyrethroids. Video recordings of bed bugs indicated that insects increased activity when they contacted sublethal doses of deltamethrin. Insecticide barriers of chlorfenapyr or deltamethrin did not prevent bed bugs from reaching a warmed blood source and acquiring blood meals. We discuss the impact of these responses on bed bug control practices.

  13. INVESTIGATION OF FUEL CHEMISTRY AND BED PERFORMANCE IN A FLUIDIZED BED BLACK LIQUOR STEAM REFORMER

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2003-12-01

    The University of Utah project ''Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer'' (DOE award number DE-FC26-02NT41490) was developed in response to a solicitation for projects to provide technical support for black liquor and biomass gasification. The primary focus of the project is to provide support for a DOE-sponsored demonstration of MTCI's black liquor steam reforming technology at Georgia-Pacific's paper mill in Big Island, Virginia. A more overarching goal is to improve the understanding of phenomena that take place during low temperature black liquor gasification. This is achieved through five complementary technical tasks: (1) construction of a fluidized bed black liquor gasification test system, (2) investigation of bed performance, (3) evaluation of product gas quality, (4) black liquor conversion analysis and modeling and (5) computational modeling of the Big Island gasifier. Four experimental devices have been constructed under this project. The largest facility, which is the heart of the experimental effort, is a pressurized fluidized bed gasification test system. The system is designed to be able to reproduce conditions near the black liquor injectors in the Big Island steam reformer, so the behavior of black liquor pyrolysis and char gasification can be quantified in a representative environment. The gasification test system comprises five subsystems: steam generation and superheating, black liquor feed, fluidized bed reactor, afterburner for syngas combustion and a flue gas cooler/condenser. The three-story system is located at University of Utah's Industrial Combustion and Gasification Research Facility, and all resources there are available to support the research.

  14. “A built bed is a filled bed?” An empirical re-examination

    NARCIS (Netherlands)

    E.K.A. van Doorslaer (Eddy); R.C.J.A. van Vliet (René)

    1989-01-01

    textabstractThis article provides an empirical re-examination of the relationship between regional hospital bed supply and the utilization of hospital care. It tests the hypothesis that the divergence of findings between studies based on micro-data (at the individual level) and those based on

  15. A bioassay for studying behavioural responses of the common bed bug, Cimex lectularius (Hemiptera: Cimicidae) to bed bug-derived volatiles.

    Science.gov (United States)

    Weeks, E N I; Logan, J G; Gezan, S A; Woodcock, C M; Birkett, M A; Pickett, J A; Cameron, M M

    2011-02-01

    The common bed bug, Cimex lectularius (Hemiptera: Cimicidae), has recently re-emerged in increasing numbers, distribution and intensity of infestation in many countries. Current control relies on the application of residual pesticides; but, due to the development of insecticide resistance, there is a need for new tools and techniques. Semiochemicals (behaviour and physiology modifying chemicals) could be exploited for management of bed bugs. However, in order to identify semiochemicals that can be utilised in monitoring or control, a suitable olfactometer is needed that enables the study of the responses of bed bugs to volatile chemicals. Previous studies have used olfactometers that do not separate olfactory responses from responses to physical contact. In this study, a still-air olfactometer was used to measure behavioural responses to different bed bug-derived volatiles presented in an odour pot. Bed bugs were significantly more likely to visit the area above the odour pot first, and more frequently, in the presence of volatiles from bed bug-exposed paper but not in the presence of volatiles from conspecific bed bugs. Bed bug activity was found to be dependent on the presence of the volatiles from bed bug-exposed paper, the time during the scotophase and the sex of the insect being tested. The still-air olfactometer could be used to test putative semiochemicals, which would allow an understanding of their behavioural role in bed bug ecology. Ultimately, this could lead to the identification of new semiochemical tools for bed bug monitoring and control.

  16. Effectiveness of Bed Bug Pesticides

    Science.gov (United States)

    Before EPA allows a bed bug claim on a label, the product must be supported by data showing it will kill bed bugs when applied according to the label. Also consider factors such as extent of infestation, site preparation, and insect life stages.

  17. Bed Bug Laws and Regulations

    Science.gov (United States)

    21 states have some level of regulation with regard to bed bugs. Most of these requirements focus on hotels and landlords or other property managers. The Department of Housing and Urban Development has guidance on controlling bed bugs in public housing.

  18. NUCLA Circulating Atmospheric Fluidized Bed Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    1992-02-01

    The objective of this DOE Cooperative Agreement is to conduct a cost-shared clean coal technology project to demonstrate the feasibility of circulating fluidized bed combustion technology and to evaluate economic, environmental, and operational benefits of CFB steam generators on a utility scale. At the conclusion of the Phase 2 program, testing related to satisfying these objectives was completed. Data analysis and reporting are scheduled for completion by October 1991. (VC)

  19. Bed-To-Wall Heat Transfer in a Supercritical Circulating Fluidised Bed Boiler

    Directory of Open Access Journals (Sweden)

    Błaszczuk Artur

    2014-06-01

    Full Text Available The purpose of this work is to find a correlation for heat transfer to walls in a 1296 t/h supercritical circulating fluidised bed (CFB boiler. The effect of bed-to-wall heat transfer coefficient in a long active heat transfer surface was discussed, excluding the radiation component. Experiments for four different unit loads (i.e. 100% MCR, 80% MCR, 60% MCR and 40% MCR were conducted at a constant excess air ratio and high level of bed pressure (ca. 6 kPa in each test run. The empirical correlation of the heat transfer coefficient in a large-scale CFB boiler was mainly determined by two key operating parameters, suspension density and bed temperature. Furthermore, data processing was used in order to develop empirical correlation ranges between 3.05 to 5.35 m·s-1 for gas superficial velocity, 0.25 to 0.51 for the ratio of the secondary to the primary air, 1028 to 1137K for bed temperature inside the furnace chamber of a commercial CFB boiler, and 1.20 to 553 kg·m-3 for suspension density. The suspension density was specified on the base of pressure measurements inside the boiler’s combustion chamber using pressure sensors. Pressure measurements were collected at the measuring ports situated on the front wall of the combustion chamber. The obtained correlation of the heat transfer coefficient is in agreement with the data obtained from typical industrial CFB boilers.

  20. Research on surface traction calibration method of drum test-bed system%汽车转鼓试验台表面牵引力标定方法研究

    Institute of Scientific and Technical Information of China (English)

    李宁; 赵树朋; 牛博英; 刘丹

    2012-01-01

    为了确保转鼓试验台系统的精度,需要对其系统进行标定.标定的主要问题是如何对确定量进行测量,并通过何种调节手段,达到显示值与实际值之间的偏差符合精度要求的目的.汽车转鼓试验台转鼓主轴与转鼓电机主轴是重合的,转鼓通过电机主轴将其表面上牵引力传递给电机转子,依靠转子和定子的相互作用,牵引力将被传至与定子固定连接的电机外壳上.因此在电机外壳上安装测力传感器测量电机外壳切线方向上的力实现对转鼓试验台表面牵引力的测量.设计采用双向标定臂可以减小额外扭矩的影响,确保了汽车转鼓试验台表面牵引力的测试精度要求.%The drum test-bed system needs to be calibrated in order to ensure its accuracy, The main problem of calibration is how to measure the determination of quantity so that deviation between the display and actual values can meet the accuracy requirements by some adjustment means, Drum shaft of automobile chassis dynamometer is coincident with the drum motor shaft, the traction of drum surface is transmitted to the motor rotor through the motor shaft, Eventually the traction is transmitted to the motor casing connected with the stator relying on the rotor and stator interaction. Therefore the drum test bench surface traction can be measured from the motor casing tangential force using force sensor mounted on the motor casing. The design adopts bidirectional calibration arm, it can decrease the effect of extra torque to ensure the test precision of automobile chassis dynamometer surface traction

  1. Fluidized bed gasification of industrial solid recovered fuels.

    Science.gov (United States)

    Arena, Umberto; Di Gregorio, Fabrizio

    2016-04-01

    The study evaluates the technical feasibility of the fluidized bed gasification of three solid recovered fuels (SRFs), obtained as co-products of a recycling process. The SRFs were pelletized and fed to a pilot scale bubbling fluidized bed reactor, operated in gasification and co-gasification mode. The tests were carried out under conditions of thermal and chemical steady state, with a bed of olivine particles and at different values of equivalence ratio. The results provide a complete syngas characterization, in terms of its heating value and composition (including tars, particulates, and acid/basic pollutants) and of the chemical and physical characterization of bed material and entrained fines collected at the cyclone outlet. The feasibility of the fluidized bed gasification process of the different SRFs was evaluated with the support of a material and substance flow analysis, and a feedstock energy analysis. The results confirm the flexibility of fluidized bed reactor, which makes it one of the preferable technologies for the gasification of different kind of wastes, even in co-gasification mode. The fluidized bed gasification process of the tested SRFs appears technically feasible, yielding a syngas of valuable quality for energy applications in an appropriate plant configuration.

  2. Long-duration bed rest as an analog to microgravity.

    Science.gov (United States)

    Hargens, Alan R; Vico, Laurence

    2016-04-15

    Long-duration bed rest is widely employed to simulate the effects of microgravity on various physiological systems, especially for studies of bone, muscle, and the cardiovascular system. This microgravity analog is also extensively used to develop and test countermeasures to microgravity-altered adaptations to Earth gravity. Initial investigations of bone loss used horizontal bed rest with the view that this model represented the closest approximation to inactivity and minimization of hydrostatic effects, but all Earth-based analogs must contend with the constant force of gravity by adjustment of the G vector. Later concerns about the lack of similarity between headward fluid shifts in space and those with horizontal bed rest encouraged the use of 6 degree head-down tilt (HDT) bed rest as pioneered by Russian investigators. Headward fluid shifts in space may redistribute bone from the legs to the head. At present, HDT bed rest with normal volunteers is the most common analog for microgravity simulation and to test countermeasures for bone loss, muscle and cardiac atrophy, orthostatic intolerance, and reduced muscle strength/exercise capacity. Also, current physiologic countermeasures are focused on long-duration missions such as Mars, so in this review we emphasize HDT bed rest studies with durations of 30 days and longer. However, recent results suggest that the HDT bed rest analog is less representative as an analog for other important physiological problems of long-duration space flight such as fluid shifts, spinal dysfunction and radiation hazards.

  3. Integrated approach in fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Bruyet, B.; Gautrin, M. [CERCHAR, Mazingarbe (France)

    1998-12-31

    Atmospheric fluidized bed technology for combustion is frequently found in different advanced power and steam generation systems, because the fluidization provides operating conditions which are favourable for pollutant control and also offers the possibility to utilise a wide range of fuels. The main objective of the study was to contribute to the development of a methodology for an easier global approach of the implementation of atmospheric fluidized bed reactors and upstream elements associated with taking into account the characteristics of fuels and sorbents, the requirements on gaseous pollutants and on solid by-products utilisation. Previous tests done in CERCHAR`s facilities were scrutinised, additional tests at laboratory and pilot level were carried out, some industrial plants were considered. Several fuels were considered (brown coals, coals, slurry,...), with a special attention to Gottelborn reference coal and Rheinbraun lignite. Experimental results and tentative conclusions viz. fuel characterization, batch fluidization set-up, 1 MW atmospheric fluidized bed pilot, ash utilisation/disposal, methodology and management of preliminary testing are presented. 12 refs., 18 figs., 13 tabs.

  4. Debris-bed friction of hard-bedded glaciers

    Science.gov (United States)

    Cohen, D.; Iverson, N.R.; Hooyer, T.S.; Fischer, U.H.; Jackson, M.; Moore, P.L.

    2005-01-01

    [1] Field measurements of debris-bed friction on a smooth rock tablet at the bed of Engabreen, a hard-bedded, temperate glacier in northern Norway, indicated that basal ice containing 10% debris by volume exerted local shear traction of up to 500 kPa. The corresponding bulk friction coefficient between the dirty basal ice and the tablet was between 0.05 and 0.08. A model of friction in which nonrotating spherical rock particles are held in frictional contact with the bed by bed-normal ice flow can account for these measurements if the power law exponent for ice flowing past large clasts is 1. A small exponent (n glacier sliding at 20 m a-1 with a geothermally induced melt rate of 0.006 m a-1 and an effective pressure of 300 kPa can exceed 100 kPa. Debris-bed friction can therefore be a major component of sliding resistance, contradicting the common assumption that debris-bed friction is negligible. Copyright 2005 by the American Geophysical Union.

  5. Multi-bed patient room architectural evaluation

    Directory of Open Access Journals (Sweden)

    Evangelia Sklavou

    2016-12-01

    Full Text Available Introduction: Leveraging the physical environment’s merits is crucial in healthcare settings towards fostering sustainable healing conditions. In the future, the need to retrofit hospitals already appears more probable than to build new facilities. In Greece, holistic healthcare architecture has significant potential and room to develop. Aim: The architectural research of multi-bed patient room environment. Method: A sample of multi-bed patient rooms of a Greek hospital was studied per architectural documentation and user evaluation survey. Beyond recording the existing situation and user experience, user group differences and the influence of window proximity were studied. The survey sample was based on convenience and comprised 160 patients and 136 visitors. Statistical analysis was performed in SPSS 20, using chi-square exact tests of independence. The chosen level of significance was p < 0.05. Results: Architectural documentation showed that the building morphology had a positive impact in patient rooms, with regard to sunlight penetration and view. Further solar daylight control was deemed necessary, to facilitate overall environmental comfort conditions. High spatial density and considerable disadvantages of the middle patient bed, compared to the one bedside the window and the one further in the back of the room, were also ascertained. User groups did not evaluate their surroundings significantly different, with the exception of ease of access to the view. Window proximity influenced both patients and visitors in evaluating ease of access to the view and visual discomfort. Patients were further affected on window size evaluation and visitors on view related aspects. Conclusions: Synergy between building form and function contributes in creating holistic sustainable healing environments. User evaluation can deviate from objective documentation. Patients and visitors experienced the patient room in a similar manner. The middle bed was

  6. Mathematical modelling of MSW incineration on a travelling bed.

    Science.gov (United States)

    Yang, Y B; Goh, Y R; Zakaria, R; Nasserzadeh, V; Swithenbank, J

    2002-01-01

    The rising popularity of incineration of municipal solid waste (MSW) calls for detailed mathematical modelling and understanding of the incineration process. In this paper, governing equations for mass, momentum and heat transfer for both solid and gaseous phases in a moving bed in a solid-waste incineration furnace are described and relevant sub-models are presented. The burning rates of volatile hydrocarbons in the moving bed of solids are limited not only by the reaction kinetics but also the mixing of the volatile fuels with the under-fire air. The mixing rate is averaged across a computation cell and correlated to a number of parameters including local void fraction of the bed, gas velocity and a length scale comparable to the particle size in the bed. A correlation equation is also included to calculate the mixing in the freeboard area immediately next to the bed surface. A small-scale fixed bed waste incinerator was built and test runs were made in which total mass loss from the bed, temperature and gas composition at different locations along the bed height were measured. A 2-D bed-modelling program (FLIC) was developed which incorporates the various sub-process models and solves the governing equations for both gases and solids. Thermal and chemical processes are mainly confined within a layer about 5-9 times in thickness of the averaged particle size in the burning bed. For a large part of the burning process, the total mass loss rate was constant until the solid waste was totally dried out and a period of highly rising CO emission followed. The maximum bed temperature was around 1200 K. The whole burning process ended within 60 min. Big fluctuations in species concentration were observed due to channelling and subsequent 'catastrophic' changes in the local bed conditions. Reasonably good agreement between modelling and measurements has been achieved. Yet the modelling work is complicated by the channelling phenomenon in the bed. Numerical simulations

  7. Properties of Concrete Incorporating Bed Ash from Circulating Fluidized Bed Combustion and Ground Granulates Blast-furnace Slag

    Institute of Scientific and Technical Information of China (English)

    CHENG An; HSU Hui-Mi; CHAO Sao-Jeng

    2011-01-01

    The properties of concrete incorporating circulating fluidized bed combustion (CFBC) bed ash and ground granulates blast-furnace slag (GGBS) were studied. Compressive strength,drying shrinkage, mercury intrusion porosimetry (MIP), scanning electronic microscopy (SEM), and X-ray diffraction (XRD) of concrete samples containing CFBC bed ash and GGBS were used. This work used initial surface absorption test (ISAT) and rapid chloride penetration test (RCPT) on concrete to measure the absorption and the ability of concrete to resist chloride ion characteristics for different concrete samples containing CFBC bed ash and GGBS. Open circuit potential (OCP), direct current polarization resistance were obtained to evaluate rebar corrosion. The CFBC bed ash was X-ray amorphous and consist of SiO2, A12O3 and CaO compounds. As the replacement of CFBC for sand increases, the rate of initial surface absorption (ISA) increases but compressive strength decreases.When the content of CFBC bed ash replacement for sand maintains constant, the replacement of GGBS for cement increases, compressive strength increases but the rate of ISA decreases. Chloride and corrosion resistance of rebar significantly improve by utilizing a proper amount of CFBC bed ash and GGBS in concrete.

  8. Abrasion behavior of graphite pebble in lifting pipe of pebble-bed HTR

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Ke; Su, Jiageng [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Zhou, Hongbo [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Chinergy Co., LTD., Beijing 100193 (China); Peng, Wei; Liu, Bing [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Yu, Suyun, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Educations, Tsinghua University, Beijing 10084 (China)

    2015-11-15

    Highlights: • Quantitative determination of abrasion rate of graphite pebbles in different lifting velocities. • Abrasion behavior of graphite pebble in helium, air and nitrogen. • In helium, intensive collisions caused by oscillatory motion result in more graphite dust production. - Abstract: A pebble-bed high-temperature gas-cooled reactor (pebble-bed HTR) uses a helium coolant, graphite core structure, and spherical fuel elements. The pebble-bed design enables on-line refueling, avoiding refueling shutdowns. During circulation process, the pebbles are lifted pneumatically via a stainless steel lifting pipe and reinserted into the reactor. Inevitably, the movement of the fuel elements as they recirculate in the reactor produces graphite dust. Mechanical wear is the primary source of graphite dust production. Specifically, the sources are mechanisms of pebble–pebble contact, pebble–wall (structural graphite) contact, and fuel handling (pebble–metal abrasion). The key contribution to graphite dust production is from the fuel handling system, particularly from the lifting pipe. During pneumatic lift, graphite pebbles undergo multiple collisions with the stainless steel lifting pipe, thereby causing abrasion of the graphite pebbles and producing graphite dust. The present work explored the abrasion behavior of graphite pebble in the lifting pipe by measuring the abrasion rate at different lifting velocities. The abrasion rate of the graphite pebble in helium was found much higher than those in air and nitrogen. This gas environment effect could be explained by either tribology behavior or dynamic behavior. Friction testing excluded the possibility of tribology reason. The dynamic behavior of the graphite pebble was captured by analysis of the audio waveforms during pneumatic lift. The analysis results revealed unique dynamic behavior of the graphite pebble in helium. Oscillation and consequently intensive collisions occur during pneumatic lift, causing

  9. MARKETING MIX BY BED OCCUPANCY RATIO (BOR

    Directory of Open Access Journals (Sweden)

    Abdul Muhith

    2017-04-01

    Full Text Available Introduction: Bed Occupancy Ratio (BOR in RSI Arafah Mojosari during the last three years are at under ideal rate and the lowest of the three existing hospitals in the area of Mojosari. The purpose of this study was to determine the relationship marketing mix with Bed Occupancy Ratio in RSI Arafah Mojosari. Methods: This research uses analytic methods with crossectional approach. Variables in the study is marketing mix and Bed Occupancy Ratio (BOR. The population in this study were all patients hospitalized in the RSI Arafah Mojosari. Samples amounted 44 respondents taken by the Stratified random sampling technique. Data were collected using the questionnaire and analyzed using Fisher's Exact test. Result: The results obtained more than 50% of respondents (59.1% rate well against the marketing mix is developed by the hospital management and the majority of respondents (79.5% are in the treatment room that has a number BOR is not ideal. Fisher Exact test test results obtained probabililty value=0.02<0.05 so that H0 is rejected, which means there is a relationship marketing mix with the Bed Occupancy Ratio in RSI Arafah Mojosari. Discussion: Hospitals which able to develop the marketing mix very well, can attract consumers to use inpatient services at the hospital, with that BOR value will increase as the increased use of inpatient services. Hospital management must be able to formulate a good marketing mix strategy that hospital marketing objectives can be achieved. Conformity between service quality and service rates must be addressed, otherwise it extent of media promotions can attract patients to inpatient services.

  10. Design of measurement and control system for Hall electric propulsion longevity test bed%霍尔电推进长寿命试验台测控系统研制

    Institute of Scientific and Technical Information of China (English)

    邱刚; 康小录; 乔彩霞; 冯彦

    2012-01-01

    In allusion to the actual measurement and control requirements for Hall electric propulsion longevity test bed, IPC+DAQ 2205+PCI 1721 based hardware and Delphi 7+SQL based sottware of measurement and control system are built up and dissertated in detail in this paper. The high-per- formance data acquisition card DAQ 2205 and analog controlled quantity output card PCI 1721, both based on PCI bus, are used to realize the data aquisition and analog controlled quantity output for the measurement and control system. Multi-tasking and rapid response requirements are met by mul- ti-threaded programming architecture. The running tests of the measurement and control system show that the control precision, response speed, reliability and friendly human-computer interaction can meet the specific requirements of longevity experiment for the Hall electric thruster.%针对霍尔电推进长寿命试验台的测控需求,提出并详细论述了IPC+DAQ2205+PCI1721的测控系统硬件和Delphi7+SQL的测控系统软件。采用基于PCI总线的高性能数据采集卡DAQ2205和模拟控制量输出卡PCI1721完成测控系统的数据采集和模拟控制量的输出控制。采用多线程的程序设计架构实现测控系统多任务和快速响应的需求。测控系统实际运行测试表明其测控精度、响应速度、可靠性和人机交互友好性等方面都能很好地满足霍尔推力器长寿命试验的具体要求。

  11. Uniqueness property for quasiharmonic functions

    Directory of Open Access Journals (Sweden)

    Sevdiyor A. Imomkulov

    2014-10-01

    Full Text Available In this paper we consider a class of continuous functions, called quasiaharmonic functions, admitting best approximations by harmonic polynomials. In this class we prove a uniqueness theorem by analogy with the analytic functions.

  12. Osteoporosis: Unique to Older Adults

    Science.gov (United States)

    ... our e-newsletter! Aging & Health A to Z Osteoporosis Unique to Older Adults This section provides information ... and widely-prescribed medications for the treatment of osteoporosis. Some serious side effects of these medication have ...

  13. Nutrition: Unique to Older Adults

    Science.gov (United States)

    ... our e-newsletter! Aging & Health A to Z Nutrition Unique to Older Adults This section provides information ... teeth that are needed for grinding up food, nutrition suffers. If you are unable to chew and ...

  14. Exercise-induced pyruvate dehydrogenase activation is not affected by 7 days of bed rest

    DEFF Research Database (Denmark)

    Kiilerich, Kristian; Jørgensen, Stine Ringholm; Biensø, Rasmus Sjørup

    2011-01-01

    To test the hypothesis that physical inactivity impairs the exercise-induced modulation of pyruvate dehydrogenase (PDH), 6 healthy normally physically active male subjects completed 7 days of bed rest. Before and immediately after the bed rest, the subjects completed an OGTT and a one-legged knee...... after bed rest than before, indicating glucose intolerance. There were no differences in lactate release/uptake across the exercising muscle before and after bed rest, but glucose uptake after 40min of exercise was larger (P=0.05) before bed rest than after. Muscle glycogen content tended to be higher...

  15. Study of fluidized-bed desulfurization with zinc ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Grindley, T

    1991-01-01

    Previous work established the technical feasibility of desulfurizing the hot product gases of coal gasification with fixed beds of a regenerable zinc ferrite sorbent. This process, intended for integration with coal gasifiers and gas turbines, has been tested and studied in considerable detail in a process development unit. Though possessing the advantages of high-sulfur absorption at low-sulfur breakthrough and the lack of sorbent attrition characteristic of a stationary bed, fixed beds also have inherent disadvantages: susceptibility to plugging by particles and a large diluent requirement during regeneration to control the reaction zone temperature. Therefore, METC conducted a scoping laboratory test program to determine the desulfurizing capability of fluid beds of zinc ferrite. Results from this program are presented. The results generally demonstrated that fluid beds of zinc ferrite have the potential to lower the H{sub 2}S level in hot gas from 10,000 to 10 ppmv. To achieve this at a high-sorbent sulfur loading would require two fluid-bed stages. Sorbent attrition appears to be acceptably low. Planned future activities include tests at high pressure with both simulated gas and in a gasifier sidestream.

  16. Air passivation of metal hydride beds for waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Klein, J. E.; Hsu, R. H. [Savannah River National Laboratory, Aiken, SC 29808 (United States)

    2008-07-15

    One waste acceptance criteria for hydride bed waste disposal is that the bed be non-pyrophoric. Batch-wise air ingress tests were performed which determined the amount of air consumed by a metal hydride bed. A desorbed, 4.4 kg titanium prototype hydride storage vessel (HSV) produced a 4.4 deg.C internal temperature rise upon the first air exposure cycle and a 0.1 deg.C temperature rise upon a second air exposure. A total of 346 sec air was consumed by the bed (0.08 sec per gram Ti). A desorbed, 9.66 kg LaNi{sub 4.25}Al{sub 0.75} prototype storage bed experienced larger temperature rises over successive cycles of air ingress and evacuation. The cycles were performed over a period of days with the bed effectively passivated after the 12. cycle. Nine to ten STP-L of air reacted with the bed producing both oxidized metal and water. (authors)

  17. Fluidized bed combustion of pesticide-manufacture liquid wastes

    Directory of Open Access Journals (Sweden)

    SAŠA MILETIĆ

    2010-04-01

    Full Text Available Industrial liquid wastes can be in the form of solutions, suspensions, sludges, scums or waste oil and have organic properties. The objective of this work was to demonstrate the technical feasibility of a fluidized bed as a clean technology for burning liquid waste from a pesticide production plant. The combustion of liquid waste mixtures, obtained from realistic samples, was investigated in a pilot scale fluidized bed with quartz sand particles of 0.63–1.25 mm in diameter and 2610 kg/m3 in density at 800–950 °C. To ensure complete combustion of liquid waste and additional fuel, the combustion chamber was supplied with excess air and the U/UmF (at ambient temperature was in between 1.1 and 2.3. In the fluidized bed chamber, liquid waste, additional liquid fuel and air can be brought into intense contact sufficient to permit combustion in bed without backfire problems. The experimental results show that the fluidized bed furnace offers excellent thermal uniformity and temperature control. The results of the combustion tests showed that degradation of liquid wastes can be successfully realized in a fluidized bed with no harmful gaseous emissions by ensuring that the temperatures of both the bed and the freeboard are not lower than 900 °C.

  18. Hospital bed ventilation: impact of operation mode on exposure

    DEFF Research Database (Denmark)

    Bolashikov, Zhecho Dimitrov; Melikov, Arsen Krikor; Barova, Mariya

    2014-01-01

    Full-scale measurements were performed in a climate chamber set as a two-bed hospital room with overhead ventilation. Air temperature was kept constant at 22 °C. Two breathing thermal manikins were used to mimic a sick patient lying sideways in one of the beds and a doctor. A thermal dummy mimicked...... a second patient lying in the other bed. The doctor stood up 0.55 m from the bed facing the sick patient. Two pairs of localized ventilation units were attached near the heads of both patients alongside the beds to capture, clean and release the captured exhaled air from the lying patients. When the bed...... and droplet nuclei of less than 3 μm aerodynamic diameter. Two modes of operation of the bed incorporated ventilation unit were tested: releasing the cleaned air upwards (pull mode) or supplying it sideways over the lying patient (“push and pull” mode). The strategy to exhaust pollutants close o release...

  19. Pulsed atmospheric fluidized bed combustion. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    ThermoChem, under contract to the Department of Energy, conducted extensive research, development and demonstration work on a Pulsed Atmospheric Fluidized Bed Combustor (PAFBC) to confirm that advanced technology can meet these performance objectives. The ThermoChem/MTCI PAFBC system integrates a pulse combustor with an atmospheric bubbling-bed type fluidized bed combustor (BFBC) In this modular configuration, the pulse combustor burns the fuel fines (typically less than 30 sieve or 600 microns) and the fluidized bed combusts the coarse fuel particles. Since the ThermoChem/MTCI PAFBC employs both the pulse combustor and the AFBC technologies, it can handle the full-size range of coarse and fines. The oscillating flow field in the pulse combustor provides for high interphase and intraparticle mass transfer rates. Therefore, the fuel fines essentially burn under kinetic control. Due to the reasonably high temperature (>1093 C but less than the temperature for ash fusion to prevent slagging), combustion of fuel fines is substantially complete at the exit of the pulse combustor. The additional residence time of 1 to 2 seconds in the freeboard of the PAFBC unit then ensures high carbon conversion and, in turn, high combustion efficiency. A laboratory unit was successfully designed, constructed and tested for over 600 hours to confirm that the PAFBC technology could meet the performance objectives. Subsequently, a 50,000 lb/hr PAFBC demonstration steam boiler was designed, constructed and tested at Clemson University in Clemson, South Carolina. This Final Report presents the detailed results of this extensive and successful PAFBC research, development and demonstration project.

  20. Bed Bugs: The Australian Response

    Science.gov (United States)

    Doggett, Stephen L.; Orton, Christopher J.; Lilly, David G.; Russell, Richard C.

    2011-01-01

    Australia has experienced a sudden and unexpected resurgence in bed bug infestations from both Cimex lectularius L. and Cimex hemipterus F. A survey in 2006 revealed that infestations had increased across the nation by an average of 4,500% since the start of the decade. In response, a multi-disciplinary approach to combat the rise of this public health pest was implemented and involved the coordinated efforts of several organizations. The key components of the strategy included the introduction of a pest management standard ‘A Code of Practice for the Control of Bed Bug Infestations in Australia’ that defines and promotes ‘best practice’ in bed bug eradication, the development of a policy and procedural guide for accommodation providers, education of stakeholders in best management practices, and research. These strategies continue to evolve with developments that lead to improvements in ‘best practice’ while bed bugs remain problematic in Australia. PMID:26467616

  1. Top Ten Bed Bug Tips

    Science.gov (United States)

    ... temperatures are necessary for successful heat treatment. Black plastic bags in the sun might work to kill bed ... Place the used bag in a tightly sealed plastic bag and in an outside garbage bin. 10. Turn ...

  2. Bed Bugs: The Australian Response

    Directory of Open Access Journals (Sweden)

    Richard C. Russell

    2011-04-01

    Full Text Available Australia has experienced a sudden and unexpected resurgence in bed bug infestations from both Cimex lectularius L. and Cimex hemipterus F. A survey in 2006 revealed that infestations had increased across the nation by an average of 4,500% since the start of the decade. In response, a multi-disciplinary approach to combat the rise of this public health pest was implemented and involved the coordinated efforts of several organizations. The key components of the strategy included the introduction of a pest management standard ‘A Code of Practice for the Control of Bed Bug Infestations in Australia’ that defines and promotes ‘best practice’ in bed bug eradication, the development of a policy and procedural guide for accommodation providers, education of stakeholders in best management practices, and research. These strategies continue to evolve with developments that lead to improvements in ‘best practice’ while bed bugs remain problematic in Australia.

  3. Bed Bugs: The Australian Response.

    Science.gov (United States)

    Doggett, Stephen L; Orton, Christopher J; Lilly, David G; Russell, Richard C

    2011-04-15

    Australia has experienced a sudden and unexpected resurgence in bed bug infestations from both Cimex lectularius L. and Cimex hemipterus F. A survey in 2006 revealed that infestations had increased across the nation by an average of 4,500% since the start of the decade. In response, a multi-disciplinary approach to combat the rise of this public health pest was implemented and involved the coordinated efforts of several organizations. The key components of the strategy included the introduction of a pest management standard 'A Code of Practice for the Control of Bed Bug Infestations in Australia' that defines and promotes 'best practice' in bed bug eradication, the development of a policy and procedural guide for accommodation providers, education of stakeholders in best management practices, and research. These strategies continue to evolve with developments that lead to improvements in 'best practice' while bed bugs remain problematic in Australia.

  4. Print a Bed Bug Card

    Science.gov (United States)

    Two sets of business card-sized lists of tips for prevention of bed bug infestations, one for general use around home, the other for travelers. Print a single card or a page of cards for distribution.

  5. Better backs by better beds?

    DEFF Research Database (Denmark)

    Bergholdt, Kim; Fabricius, Rasmus N; Bendix, Tom

    2008-01-01

    using the probably most relevant "worst case" data. There were no relevant difference between the effects of the water bed and the foam bed. CONCLUSION: The Waterbed and foam mattress' did influence back symptoms, function and sleep more positively as apposed to the hard mattress, but the differences...... mattresses have a positive effect on LBP, and especially a hard mattress is commonly believed to have a positive effect. METHODS: One hundred sixty CLBP patients were randomized to 1 of 3 groups, having a mattress/bed mounted in their sleeping room for 1 month. The beds were: (1) waterbed (Akva), (2) body......-conforming foam mattress (Tempur), and (3) a hard mattress (Innovation Futon). At baseline and after 4 weeks, a blinded observer interviewed the patients on LBP levels (0-10), daily function (activities of daily living, 0-30), and on the amount of sleeping hours/night. RESULTS: Because of dropout of 19 patients...

  6. Sea bed mapping and inspection

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The conference has 24 presentations on the topics: Sea bed mapping, inspection, positioning, hydrography, marine archaeology, remote operation vehicles and computerized simulation technologies, oil field activities and plans, technological experiences and problems. (tk)

  7. Comparison of the Effects of Fluidized-Bed and Fixed-Bed Reactors in Microwave-Assisted Catalytic Decomposition of TCE by Hydrogen

    Directory of Open Access Journals (Sweden)

    Lili Ren

    2012-01-01

    Full Text Available Trichloroethylene (TCE decomposition by hydrogen with microwave heating under different reaction systems was investigated. The activities of a series of catalysts for microwave-assisted TCE hydrodechlorination were tested through the fixed-bed and the fluidized-bed reactor systems. This study found that the different reaction system is suitable for different catalyst type. And there is an interactive relationship between the catalyst type and the reaction bed type.

  8. Bed bugs in healthcare settings.

    Science.gov (United States)

    Munoz-Price, L Silvia; Safdar, Nasia; Beier, John C; Doggett, Stephen L

    2012-11-01

    Infestations caused by bed bugs have resurfaced during the past decade across all continents. Even though bed bugs primarily cause skin manifestations in humans, a major stigma is placed upon people or institutions found to carry them. It is important for healthcare facilities to be prepared for this pest by implementing policies, carefully selecting materials used for hospital furniture, and educating providers on early identification and control.

  9. Bedømmelsens kompleksitet

    Directory of Open Access Journals (Sweden)

    Elsa Schmidt

    2006-03-01

    Full Text Available I artiklen sammenholdes hverdagens bedømmelser af mennesker med de bedømmelser, der sker ved eksaminer. Der er forskelle på grund af det retlige grundlag, men også ligheder. Konkrete erfaringer med klage- og ankesager gennem 8 år fra faget psykologi på landsplan opsummeres. Nogle få praktiske løsninger beskrives.

  10. Bugging forecast: unknown, disliked, occasionally intimate. Bed bugs in Germany meet unprepared people.

    Science.gov (United States)

    Seidel, Conrad; Reinhardt, Klaus

    2013-01-01

    Bed bugs appear to be feared more than vector insects and other household pests. The reasons for this exaggerated fear are not fully understood. One hypothesis is that the folk knowledge on recognising and controlling bed bugs decreased as bed bugs became rarer in the 1960s and led to irrational perceptions. Here, we examine people's ability to recognise a bed bug and their response what to do in case of an infestation. We found that 13% of a sample of 391 people in four large German cities recognised a bed bug; 15% of all respondents would call a pest controller in case of bed bug infestation. This results in the pessimistic estimate that 97% of all early-stage infestations could go untreated. We discuss additional scenarios. The effectiveness of efforts to educate people about the presence of bed bugs has never been tested, but our sample is useful to guide future studies. We found three sources of information were associated with increased recognition rates of bed bugs: a) previous contacts with bed bugs (60% recognition), b) knowledge from friends or relatives (25%) and school or education courses (15%). By contrast, people who heard of bed bugs from television, print media or the Internet showed reduced recognition rates. We propose that the former factors be tested for educational interventions. In Germany, the bed bug is an estranged creature to many people, a fact that seems to hinder rational approaches to their control.

  11. Bugging forecast: unknown, disliked, occasionally intimate. Bed bugs in Germany meet unprepared people.

    Directory of Open Access Journals (Sweden)

    Conrad Seidel

    Full Text Available Bed bugs appear to be feared more than vector insects and other household pests. The reasons for this exaggerated fear are not fully understood. One hypothesis is that the folk knowledge on recognising and controlling bed bugs decreased as bed bugs became rarer in the 1960s and led to irrational perceptions. Here, we examine people's ability to recognise a bed bug and their response what to do in case of an infestation. We found that 13% of a sample of 391 people in four large German cities recognised a bed bug; 15% of all respondents would call a pest controller in case of bed bug infestation. This results in the pessimistic estimate that 97% of all early-stage infestations could go untreated. We discuss additional scenarios. The effectiveness of efforts to educate people about the presence of bed bugs has never been tested, but our sample is useful to guide future studies. We found three sources of information were associated with increased recognition rates of bed bugs: a previous contacts with bed bugs (60% recognition, b knowledge from friends or relatives (25% and school or education courses (15%. By contrast, people who heard of bed bugs from television, print media or the Internet showed reduced recognition rates. We propose that the former factors be tested for educational interventions. In Germany, the bed bug is an estranged creature to many people, a fact that seems to hinder rational approaches to their control.

  12. Metalworking Techniques Unlock a Unique Alloy

    Science.gov (United States)

    2015-01-01

    Approached by West Hartford, Connecticut-based Abbot Ball Company, Glenn Research Center agreed to test an intriguing alloy called Nitinol 60 that had been largely unused for a half century. Using powdered metallurgy, the partners developed a method for manufacturing and working with the material, which Abbott Ball has now commercialized. Nitinol 60 provides a unique combination of qualities that make it an excellent material for ball bearings, among other applications.

  13. Dual Fluidized Bed Biomass Gasification

    Energy Technology Data Exchange (ETDEWEB)

    None

    2005-09-30

    The dual fluidized bed reactor is a recirculating system in which one half of the unit operates as a steam pyrolysis device for biomass. The pyrolysis occurs by introducing biomass and steam to a hot fluidized bed of inert material such as coarse sand. Syngas is produced during the pyrolysis and exits the top of the reactor with the steam. A crossover arm, fed by gravity, moves sand and char from the pyrolyzer to the second fluidized bed. This sand bed uses blown air to combust the char. The exit stream from this side of the reactor is carbon dioxide, water and ash. There is a second gravity fed crossover arm to return sand to the pyrolysis side. The recirculating action of the sand and the char is the key to the operation of the dual fluidized bed reactor. The objective of the project was to design and construct a dual fluidized bed prototype reactor from literature information and in discussion with established experts in the field. That would be appropriate in scale and operation to measure the relative performance of the gasification of biomass and low ranked coals to produce a high quality synthesis gas with no dilution from nitrogen or combustion products.

  14. Host-Seeking Behavior in the Bed Bug, Cimex lectularius

    Directory of Open Access Journals (Sweden)

    Vernard R. Lewis

    2011-03-01

    Full Text Available The reemergence of the bed bug, Cimex lectularius Linnaeus, has recently spawned a frenzy of public, media, and academic attention. In response to the growing rate of infestation, considerable work has been focused on identifying the various host cues utilized by the bed bug in search of a meal. Most of these behavioral studies examine movement within a confined environment, such as a Petri dish. This has prevented a more complete understanding of the insect’s host-seeking process. This work describes a novel method for studying host-seeking behavior, using various movement parameters, in a time-lapse photography system. With the use of human breath as an attractant, we qualitatively and quantitatively assessed how bed bugs navigate their environment between its harborage and the host. Levels of behavioral activity varied dramatically between bed bugs in the presence and absence of host odor. Bed bugs demonstrated not simply activation, but attraction to the chemical components of breath. Localized, stop-start host-seeking behavior or alternating periods of movement and pause were observed among bed bugs placed in the environment void of human breath, while those exposed to human breath demonstrated long range, stop-start host-seeking behavior. A more comprehensive understanding of bed bug host-seeking can lead to the development of traps and monitors that account for unique subtleties in their behavior. The time-lapse photography system uses a large, artificial environment and could also be employed to study other aspects of the insect’s behavioral patterns.

  15. Modeling biomass gasification in circulating fluidized beds

    Science.gov (United States)

    Miao, Qi

    In this thesis, the modeling of biomass gasification in circulating fluidized beds was studied. The hydrodynamics of a circulating fluidized bed operating on biomass particles were first investigated, both experimentally and numerically. Then a comprehensive mathematical model was presented to predict the overall performance of a 1.2 MWe biomass gasification and power generation plant. A sensitivity analysis was conducted to test its response to several gasifier operating conditions. The model was validated using the experimental results obtained from the plant and two other circulating fluidized bed biomass gasifiers (CFBBGs). Finally, an ASPEN PLUS simulation model of biomass gasification was presented based on minimization of the Gibbs free energy of the reaction system at chemical equilibrium. Hydrodynamics plays a crucial role in defining the performance of gas-solid circulating fluidized beds (CFBs). A 2-dimensional mathematical model was developed considering the hydrodynamic behavior of CFB gasifiers. In the modeling, the CFB riser was divided into two regions: a dense region at the bottom and a dilute region at the top of the riser. Kunii and Levenspiel (1991)'s model was adopted to express the vertical solids distribution with some other assumptions. Radial distributions of bed voidage were taken into account in the upper zone by using Zhang et al. (1991)'s correlation. For model validation purposes, a cold model CFB was employed, in which sawdust was transported with air as the fluidizing agent. A comprehensive mathematical model was developed to predict the overall performance of a 1.2 MWe biomass gasification and power generation demonstration plant in China. Hydrodynamics as well as chemical reaction kinetics were considered. The fluidized bed riser was divided into two distinct sections: (a) a dense region at the bottom of the bed where biomass undergoes mainly heterogeneous reactions and (b) a dilute region at the top where most of homogeneous

  16. Forces on stationary particles in near-bed turbulent flows

    Science.gov (United States)

    Schmeeckle, M.W.; Nelson, J.M.; Shreve, R.L.

    2007-01-01

    In natural flows, bed sediment particles are entrained and moved by the fluctuating forces, such as lift and drag, exerted by the overlying flow on the particles. To develop a better understanding of these forces and the relation of the forces to the local flow, the downstream and vertical components of force on near-bed fixed particles and of fluid velocity above or in front of them were measured synchronously at turbulence-resolving frequencies (200 or 500 Hz) in a laboratory flume. Measurements were made for a spherical test particle fixed at various heights above a smooth bed, above a smooth bed downstream of a downstream-facing step, and in a gravel bed of similarly sized particles as well as for a cubical test particle and 7 natural particles above a smooth bed. Horizontal force was well correlated with downstream velocity and not correlated with vertical velocity or vertical momentum flux. The standard drag formula worked well to predict the horizontal force, but the required value of the drag coefficient was significantly higher than generally used to model bed load motion. For the spheres, cubes, and natural particles, average drag coefficients were found to be 0.76, 1.36, and 0.91, respectively. For comparison, the drag coefficient for a sphere settling in still water at similar particle Reynolds numbers is only about 0.4. The variability of the horizontal force relative to its mean was strongly increased by the presence of the step and the gravel bed. Peak deviations were about 30% of the mean force for the sphere over the smooth bed, about twice the mean with the step, and 4 times it for the sphere protruding roughly half its diameter above the gravel bed. Vertical force correlated poorly with downstream velocity, vertical velocity, and vertical momentum flux whether measured over or ahead of the test particle. Typical formulas for shear-induced lift based on Bernoulli's principle poorly predict the vertical forces on near-bed particles. The

  17. Limestone fragmentation and attrition during fluidized bed oxyfiring

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Piero Salatino [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy)

    2010-04-15

    Attrition/fragmentation of limestone under simulated fluidized bed oxyfiring conditions was investigated by means of an experimental protocol that had been previously developed for characterization of attrition/fragmentation of sorbents in air-blown atmospheric fluidized bed combustors. The protocol was based on the use of different and mutually complementary techniques. The extent and pattern of attrition by surface wear in the dense phase of a fluidized bed were assessed in experiments carried out with a bench scale fluidized bed combustor under simulated oxyfiring conditions. Sorbent samples generated during simulated oxyfiring tests were further characterized from the standpoint of fragmentation upon high velocity impact by means of a purposely designed particle impactor. Results showed that under calcination-hindered conditions attrition and fragmentation patterns are much different from those occurring under air-blown atmospheric combustion conditions. Noteworthy, attrition/fragmentation enhanced particle sulfation by continuously regenerating the exposed particle surface. 13 refs., 8 figs.

  18. Fluidized bed combustion of high ash Singareni coal

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, M.K.; Biswas, R.R.; Mukherjee, S.K.; Talapatra, P.C.; Roy, R.U.; Rao, S.K.; Sen, M.M.

    1986-04-01

    Fluid bed combustion is comparatively a new technology for efficient combustion of high ash coals, which constitute the bulk of Indian coal resources. A 2-tonne equivalent steam per hour fluid bed combustion boiler was installed at the CPRI for experimentation with Indian coals and this paper discusses the salient features of tests conducted in the unit with minus 6 mm high ash Singareni coal of Andhra Pradesh. Data on combustion, heat transfer and heat utilization characteristics of the boiler under varying operating conditions show that high ash Singareni coal slacks can be burnt efficiently with high thermal efficiency, combustion efficiency and heat transfer rates from bed to surface in direct contact in a fluid bed combustion boiler. 3 refs., 5 figs., 4 tabs.

  19. Phase-Plane Invariant Analysis of Pressure Fluctuations in Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    WANG Xiaoliang; HE Rong; Toshiyuki Suda; Junichi Sato

    2007-01-01

    Partial agglomeration is a major problem in fluidized beds. A chaotic analytical method based on the phase-plane invariant of the pressure fluctuations in the fluidized beds has been used to warn of agglomeration at an early stage. Cold tests (no combustion) and hot tests (combustion) in fluidized beds show that the phase-plane invariant of the pressure fluctuations can distinguish the dynamic behavior of fluidized beds with different flow rates in cold tests. With combustion, when the flow rate was kept constant, agglomeration was detected very early by looking at the phase-plane invariant. The phase-plane invariant can be used to distinguish changes in fluidized beds due to changes in the flow rate, agglomeration, or various other factors. Therefore, this reliable agglomeration early warning system can be used for better control of circulating fluidized beds.

  20. Environmental impact assessment for steeply dipping coal beds: North Knobs site

    Energy Technology Data Exchange (ETDEWEB)

    1978-11-08

    The US Department of Energy is funding an underground coal gasification (UCG) project in steeply dipping coal beds (SDB), at North Knobs, about 8 miles west of Rawlins, Carbon County, Wyoming. The project is being conducted to determine the technical, economic and environmental viability of such a technology. The development of SDB is an interesting target for UCG since such beds contain coals not normally mineable economically by ordinary techniques. Although the underground gasification of SDB has not been attempted in the US, Soviet experience and theoretical work indicate that the gasification of SDB in place offers all the advantages of underground gasification of horizontal coal seams plus some unique characteristics. The steep angle of dip helps to channel the produced gases up dip to offtake holes and permits the ash and rubble to fall away from the reaction zone helping to mitigate the blocking of the reaction zone in swelling coals. The intersection of SDB with the surface makes the seam accessible for drilling and other preparation. The tests at the North Knobs site will consist of three tests, lasting 20, 80 and 80 days, respectively. A total of 9590 tons of coal is expected to be gasified, with surface facilities utilizing 15 acres of the total section of land. The environmental effects of the experiment are expected to be very small. The key environmental impact is potential groundwater contamination by reaction products from coal gasification. There is good evidence that the surrounding coal effectively blocks the migration of these contaminants.

  1. Status of the fluidized bed unit

    Energy Technology Data Exchange (ETDEWEB)

    Williams, P.M.; Wade, J.F.

    1994-06-01

    Rocky Flats has a serious mixed waste problem. No technology or company has a license and available facilities to remedy this dilemma. One solution under study is to use a catalytic fluidized bed unit to destroy the combustible portion of the mixed waste. The fluidized bed thermal treatment program at Rocky Flats is building on knowledge gained over twenty years of successful development activity. The FBU has numerous technical advantages over other thermal technologies to treat Rocky Flats` mixed waste, the largest being the lower temperature (700{degrees}C versus 1000{degrees}C) which reduces acid corrosion and mechanical failures and obviates the need for ceramic lining. Successful demonstrations have taken place on bench, pilot, and full-scale tests using radioactive mixed wastes. The program is approaching implementation and licensing of a production-scale fluidized bed system for the safe treatment of mixed waste. The measure for success on this project is the ability to work closely with the community to jointly solve problems and respond to concerns of mixed waste treatment at Rocky Flats.

  2. Ice sheets on plastically-yielding beds

    Science.gov (United States)

    Hewitt, Ian

    2016-11-01

    Many fast flowing regions of ice sheets are underlain by a layer of water-saturated sediments, or till. The rheology of the till has been the subject of some controversy, with laboratory tests suggesting almost perfectly plastic behaviour (stress independent of strain rate), but many models adopting a pseudo-viscous description. In this work, we consider the behaviour of glaciers underlain by a plastic bed. The ice is treated as a viscous gravity current, on a bed that allows unconstrained slip above a critical yield stress. This simplified description allows rapid sliding, and aims to investigate 'worst-case' scenarios of possible ice-sheet disintegration. The plastic bed results in an approximate ice-sheet geometry that is primarily controlled by force balance, whilst ice velocity is determined from mass conservation (rather than the other way around, as standard models would hold). The stability of various states is considered, and particular attention is given to the pace at which transitions between unstable states can occur. Finally, we observe that the strength of basal tills depends strongly on pore pressure, and combine the model with a description of subglacial hydrology. Implications for the present-day ice sheets in Greenland and Antarctica will be discussed. Funding: ERC Marie Curie FP7 Career Integration Grant.

  3. 49 CFR 236.336 - Locking bed.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Locking bed. 236.336 Section 236.336 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Instructions § 236.336 Locking bed. The various parts of the locking bed, locking bed supports, and tappet...

  4. Rufus Choate: A Unique Orator.

    Science.gov (United States)

    Markham, Reed

    Rufus Choate, a Massachusetts lawyer and orator, has been described as a "unique and romantic phenomenon" in America's history. Born in 1799 in Essex, Massachusetts, Choate graduated from Dartmouth College and attended Harvard Law School. Choate's goal was to be the top in his profession. Daniel Webster was Choate's hero. Choate became well…

  5. Uniqueness of PL Minimal Surfaces

    Institute of Scientific and Technical Information of China (English)

    Yi NI

    2007-01-01

    Using a standard fact in hyperbolic geometry, we give a simple proof of the uniqueness of PL minimal surfaces, thus filling in a gap in the original proof of Jaco and Rubinstein. Moreover, in order to clarify some ambiguity, we sharpen the definition of PL minimal surfaces, and prove a technical lemma on the Plateau problem in the hyperbolic space.

  6. On the Nagumo uniqueness theorem

    OpenAIRE

    Octavian G. Mustafa; O'Regan, Donal

    2011-01-01

    By a convenient reparametrisation of the integral curves of a nonlinear ordinary differential equation (ODE), we are able to improve the conclusions of the recent contribution [A. Constantin, Proc. Japan Acad. {\\bf 86(A)} (2010), 41--44]. In this way, we establish a flexible uniqueness criterion for ODEs without Lipschitz-like nonlinearities.

  7. The Lasso Problem and Uniqueness

    CERN Document Server

    Tibshirani, Ryan J

    2012-01-01

    The lasso is a popular tool for sparse linear regression, especially for problems in which the number of variables p exceeds the number of observations n. But when p>n, the lasso criterion is not strictly convex, and hence it may not have a unique minimum. An important question is: when is the lasso solution well-defined (unique)? We review results from the literature, which show that if the predictor variables are drawn from a continuous probability distribution, then there is a unique lasso solution with probability one, regardless of the sizes of n and p. We also show that this result extends easily to $\\ell_1$ penalized minimization problems over a wide range of loss functions. A second important question is: how can we deal with the case of non-uniqueness in lasso solutions? In light of the aforementioned result, this case really only arises when some of the predictor variables are discrete, or when some post-processing has been performed on continuous predictor measurements. Though we certainly cannot c...

  8. Rapid ignition of fluidized bed boiler

    Science.gov (United States)

    Osborn, Liman D.

    1976-12-14

    A fluidized bed boiler is started up by directing into the static bed of inert and carbonaceous granules a downwardly angled burner so that the hot gases cause spouting. Air is introduced into the bed at a rate insufficient to fluidize the entire bed. Three regions are now formed in the bed, a region of lowest gas resistance, a fluidized region and a static region with a mobile region at the interface of the fluidized and static regions. Particles are transferred by the spouting action to form a conical heap with the carbonaceous granules concentrated at the top. The hot burner gases ignite the carbonaceous matter on the top of the bed which becomes distributed in the bed by the spouting action and bed movement. Thereafter the rate of air introduction is increased to fluidize the entire bed, the spouter/burner is shut off, and the entire fluidized bed is ignited.

  9. Psudeo-seismic Imaging on CSAMT Psudeo-pulse Response of Coal Bed Methane Exploration

    Science.gov (United States)

    zhao, Y.; wu, J.

    2012-12-01

    As a unique natural gas extracted from coal beds, coal bed methane (CBM) resources has become an important source of energy in China. For CBM exploration, it is still a challenge to improve the accuracy for locating and evaluating CBM deposits due to its complicated absorption characteristics. Considering the distinct change of electromagnetic parameters caused by CBM, it is possible to detect the electromagnetic anomalies using the controlled source audio-frequency magnetotellurics (CSAMT). Psudeo-pulse response of EM was re-constructed using the impendence measured on the ground surface by CSAMT, and psudeo-seismic images can be produced using linear programming inversion with stratum model restriction. An anticline structure model was built to verify the proposal of psudeo-seismic imaging using CSAMT data. Inversion results clearly revealed the electrical structure interfaces of the model. Meanwhile, a set of CSAMT data was collected from the test area located in Heshun coal field in China. The V8 CSAMT system was used for data acquisition and the frequency ranges from 0.2 to 7680 Hz. Inversed psudeo-seismic images exactly exhibited the stratum structure and the electrical property distribution. A comparison of inversion results with exploration borehole data revealed the approximate relationship between electrical property and the CBM content. The higher the value of resistivity, the more likely the coal bed is to contain CBM. Model and field test analysis demonstrated that the psudeo-seismic image improved the CSAMT interpretation results, and it can reveal the electrical property distribution, and be applied to approximately evaluate the CBM content.

  10. Avoiding Carbon Bed Hot Spots in Thermal Process Off-Gas Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nick Soelberg; Joe Enneking

    2011-05-01

    Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (radioactive and hazardous) wastes. Test programs performed in recent years have shown that mercury in off-gas streams from processes that treat radioactive wastes can be controlled using fixed beds of activated sulfur-impregnated carbon, to levels low enough to comply with air emission regulations such as the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards. Carbon bed hot spots or fires have occurred several times during these tests, and also during a remediation of tanks that contained mixed waste. Hot spots occur when localized areas in a carbon bed become heated to temperatures where oxidation occurs. This heating typically occurs due to heat of absoption of gas species onto the carbon, but it can also be caused through external means such as external heaters used to heat the carbon bed vessel. Hot spots, if not promptly mitigated, can grow into bed fires. Carbon bed hot spots and fires must be avoided in processes that treat radioactive and mixed waste. Hot spots are detected by (a) monitoring in-bed and bed outlet gas temperatures, and (b) more important, monitoring of bed outlet gas CO concentrations. Hot spots are mitigated by (a) designing for appropriate in-bed gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) appropriate monitoring and control of gas and bed temperatures and compositions, and (c) prompt implementation of corrective actions if bed hot spots are detected. Corrective actions must be implemented quickly if bed hot spots are detected, using a graded approach and sequence starting with corrective actions that are simple, quick, cause the least impact to the process, and are easiest to recover from.

  11. Avoiding Carbon Bed Hot Spots in Thermal Process Off-Gas Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nick Soelberg; Joe Enneking

    2011-05-01

    Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (radioactive and hazardous) wastes. Test programs performed in recent years have shown that mercury in off-gas streams from processes that treat radioactive wastes can be controlled using fixed beds of activated sulfur-impregnated carbon, to levels low enough to comply with air emission regulations such as the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards. Carbon bed hot spots or fires have occurred several times during these tests, and also during a remediation of tanks that contained mixed waste. Hot spots occur when localized areas in a carbon bed become heated to temperatures where oxidation occurs. This heating typically occurs due to heat of absoption of gas species onto the carbon, but it can also be caused through external means such as external heaters used to heat the carbon bed vessel. Hot spots, if not promptly mitigated, can grow into bed fires. Carbon bed hot spots and fires must be avoided in processes that treat radioactive and mixed waste. Hot spots are detected by (a) monitoring in-bed and bed outlet gas temperatures, and (b) more important, monitoring of bed outlet gas CO concentrations. Hot spots are mitigated by (a) designing for appropriate in-bed gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) appropriate monitoring and control of gas and bed temperatures and compositions, and (c) prompt implementation of corrective actions if bed hot spots are detected. Corrective actions must be implemented quickly if bed hot spots are detected, using a graded approach and sequence starting with corrective actions that are simple, quick, cause the least impact to the process, and are easiest to recover from.

  12. Flow velocities and bed shear stresses in a stone cover under an oscillatory flow

    DEFF Research Database (Denmark)

    Stenanato, F.; Nielsen, Anders Wedel; Sumer, B. Mutlu;

    2010-01-01

    I order to get a better understanding of the interaction between the wave-induced, near-bed oscillatory flow, the stome cover and the sea bed, physical model tests were carried out. The tests were conducted in an oscillating water tunnel. The bottom of the tunnes was covered by one, two and three...

  13. Effect of head-down-tilt bed rest and hypovolemia on dynamic regulation of heart rate and blood pressure

    Science.gov (United States)

    Iwasaki, K. I.; Zhang, R.; Zuckerman, J. H.; Pawelczyk, J. A.; Levine, B. D.; Blomqvist, C. G. (Principal Investigator)

    2000-01-01

    Adaptation to head-down-tilt bed rest leads to an apparent abnormality of baroreflex regulation of cardiac period. We hypothesized that this "deconditioning response" could primarily be a result of hypovolemia, rather than a unique adaptation of the autonomic nervous system to bed rest. To test this hypothesis, nine healthy subjects underwent 2 wk of -6 degrees head-down bed rest. One year later, five of these same subjects underwent acute hypovolemia with furosemide to produce the same reductions in plasma volume observed after bed rest. We took advantage of power spectral and transfer function analysis to examine the dynamic relationship between blood pressure (BP) and R-R interval. We found that 1) there were no significant differences between these two interventions with respect to changes in numerous cardiovascular indices, including cardiac filling pressures, arterial pressure, cardiac output, or stroke volume; 2) normalized high-frequency (0.15-0.25 Hz) power of R-R interval variability decreased significantly after both conditions, consistent with similar degrees of vagal withdrawal; 3) transfer function gain (BP to R-R interval), used as an index of arterial-cardiac baroreflex sensitivity, decreased significantly to a similar extent after both conditions in the high-frequency range; the gain also decreased similarly when expressed as BP to heart rate x stroke volume, which provides an index of the ability of the baroreflex to alter BP by modifying systemic flow; and 4) however, the low-frequency (0.05-0.15 Hz) power of systolic BP variability decreased after bed rest (-22%) compared with an increase (+155%) after acute hypovolemia, suggesting a differential response for the regulation of vascular resistance (interaction, P < 0.05). The similarity of changes in the reflex control of the circulation under both conditions is consistent with the hypothesis that reductions in plasma volume may be largely responsible for the observed changes in cardiac

  14. Integrated drying and incineration of wet sewage sludge in combined bubbling and circulating fluidized bed units.

    Science.gov (United States)

    Li, Shiyuan; Li, Yunyu; Lu, Qinggang; Zhu, Jianguo; Yao, Yao; Bao, Shaolin

    2014-12-01

    An original integrated drying and incineration technique is proposed to dispose of sewage sludge with moisture content of about 80% in a circulating fluidized bed. This system combines a bubbling fluidized bed dryer with a circulating fluidized bed incinerator. After drying, sewage sludge with moisture less than 20% is transported directly and continuously from the fluidized bed dryer into a circulating fluidized bed incinerator. Pilot plant results showed that integrated drying and incineration is feasible in a unique single system. A 100 t/d Sewage Sludge Incineration Demonstration Project was constructed at the Qige sewage treatment plant in Hangzhou City in China. The operational performance showed that the main operation results conformed to the design values, from which it can be concluded that the scale-up of this technique is deemed both feasible and successful.

  15. Survey of Bartonella spp. in U.S. bed bugs detects Burkholderia multivorans but not Bartonella.

    Science.gov (United States)

    Saenz, Virna L; Maggi, Ricardo G; Breitschwerdt, Edward B; Kim, Jung; Vargo, Edward L; Schal, Coby

    2013-01-01

    Bed bugs (Cimex lectularius L.) have resurged in the United States and globally. Bed bugs are hematophagous ectoparasites of humans and other animals, including domestic pets, chickens, and bats, and their blood feeding habits contribute to their potential as disease vectors. Several species of Bartonella are re-emergent bacterial pathogens that also affect humans, domestic pets, bats and a number of other wildlife species. Because reports of both bed bugs and Bartonella have been increasing in the U.S., and because their host ranges can overlap, we investigated whether the resurgences of these medically important pathogens and their potential vector might be linked, by screening for Bartonella spp. in bed bugs collected from geographic areas where these pathogens are prevalent and from bed bugs that have been in culture in the laboratory for several years. We screened a total of 331 bed bugs: 316 bed bugs from 36 unique collections in 29 geographic locations in 13 states, 10 bed bugs from two colonies maintained in the laboratory for 3 yr, and 5 bed bugs from a colony that has been in culture since before the recent resurgence of bed bugs. Bartonella spp. DNA was screened using a polymerase chain reaction assay targeting the 16S-23S rRNA intergenic transcribed spacer region. Bartonella DNA was not amplified from any bed bug, but five bed bugs from four different apartments of an elderly housing building in North Carolina contained DNA sequences that corresponded to Burkholderia multivorans, an important pathogen in nosocomial infections that was not previously linked to an arthropod vector.

  16. Survey of Bartonella spp. in U.S. bed bugs detects Burkholderia multivorans but not Bartonella.

    Directory of Open Access Journals (Sweden)

    Virna L Saenz

    Full Text Available Bed bugs (Cimex lectularius L. have resurged in the United States and globally. Bed bugs are hematophagous ectoparasites of humans and other animals, including domestic pets, chickens, and bats, and their blood feeding habits contribute to their potential as disease vectors. Several species of Bartonella are re-emergent bacterial pathogens that also affect humans, domestic pets, bats and a number of other wildlife species. Because reports of both bed bugs and Bartonella have been increasing in the U.S., and because their host ranges can overlap, we investigated whether the resurgences of these medically important pathogens and their potential vector might be linked, by screening for Bartonella spp. in bed bugs collected from geographic areas where these pathogens are prevalent and from bed bugs that have been in culture in the laboratory for several years. We screened a total of 331 bed bugs: 316 bed bugs from 36 unique collections in 29 geographic locations in 13 states, 10 bed bugs from two colonies maintained in the laboratory for 3 yr, and 5 bed bugs from a colony that has been in culture since before the recent resurgence of bed bugs. Bartonella spp. DNA was screened using a polymerase chain reaction assay targeting the 16S-23S rRNA intergenic transcribed spacer region. Bartonella DNA was not amplified from any bed bug, but five bed bugs from four different apartments of an elderly housing building in North Carolina contained DNA sequences that corresponded to Burkholderia multivorans, an important pathogen in nosocomial infections that was not previously linked to an arthropod vector.

  17. Uniqueness theorems in linear elasticity

    CERN Document Server

    Knops, Robin John

    1971-01-01

    The classical result for uniqueness in elasticity theory is due to Kirchhoff. It states that the standard mixed boundary value problem for a homogeneous isotropic linear elastic material in equilibrium and occupying a bounded three-dimensional region of space possesses at most one solution in the classical sense, provided the Lame and shear moduli, A and J1 respectively, obey the inequalities (3 A + 2 J1) > 0 and J1>O. In linear elastodynamics the analogous result, due to Neumann, is that the initial-mixed boundary value problem possesses at most one solution provided the elastic moduli satisfy the same set of inequalities as in Kirchhoffs theorem. Most standard textbooks on the linear theory of elasticity mention only these two classical criteria for uniqueness and neglect altogether the abundant literature which has appeared since the original publications of Kirchhoff. To remedy this deficiency it seems appropriate to attempt a coherent description ofthe various contributions made to the study of uniquenes...

  18. Study and development of test-bed for brushless DC hub-motor used in EV%纯电动汽车用直流无刷轮毂电机试验台架的研究与开发

    Institute of Scientific and Technical Information of China (English)

    董铸荣; 梁松峰; 田超贺

    2012-01-01

    为解决应用于纯电动汽车上的轮毂电机测试和试验的问题,将虚拟仪器技术应用于轮毂电机性能测试与再生制动试验台的设计中.开展了试验台组成结构、测控系统工作原理的分析,设计了测控系统电路,推导了电机转速、电机扭矩、电流、电压的测量计算公式,提出了电机再生制动试验方法及试验数据的计算公式;在此基础上采用LabVIEW开发了测控系统软件,并进行了实际运行实验.实验结果证明,该试验台设计较为合理,能够将电机的性能测试试验与再生制动试验合二为一,满足了电动汽车轮毂电机相关研究的需求.%In order to solve the problems of performance testing and regenerative braking experiment for hub-motor of electric vehicle (EV), the virtual instrument technology was applied to design the test—bed for hub-motor of EV. After the analysis of the composition of the test-bed and the theory of constitution of the observer and control system, the peripheral circuit was designed. Computational formula for motor rev, motor torque, electric current, electric tension was deduced. The method of regenerative braking experiment and computational formula was presented. On this basis, LabVIEW was presented to develop software for the observer and control system. The experimental data results show that the design of the test-bed is reasonable. Hub-motor performance test and motor regenerative braking test are realized on this test-bed. It can meet the demand of experiments of hub-motor of EV.

  19. The Uniqueness of Optimal Solution for Linear Programming Problem

    Institute of Scientific and Technical Information of China (English)

    QuanlingWei; HongYan; JunWang

    2004-01-01

    This paper investigates an old problem in operations research, the uniqueness of the optimal solution to a linear programming problem. We discuss the problem on a general polyhedron, give some equivalent conditions for uniqueness testing. In addition, we discuss the implementation issues for linear programming based decision making procedures,which motivated this research.

  20. Human Odorant Reception in the Common Bed Bug, Cimex lectularius.

    Science.gov (United States)

    Liu, Feng; Liu, Nannan

    2015-11-02

    The common bed bug Cimex lectularius is a temporary ectoparasite on humans and currently resurgent in many developed countries. The ability of bed bugs to detect human odorants in the environment is critical for their host-seeking behavior. This study deciphered the chemical basis of host detection by investigating the neuronal response of olfactory sensilla to 104 human odorants using single sensillum recording and characterized the electro-physiological responses of bed bug odorant receptors to human odorants with the Xenopus expression system. The results showed that the D type of olfactory sensilla play a predominant role in detecting the human odorants tested. Different human odorants elicited different neuronal responses with different firing frequencies and temporal dynamics. Particularly, aldehydes and alcohols are the most effective stimuli in triggering strong response while none of the carboxylic acids showed a strong stimulation. Functional characterization of two bed bug odorant receptors and co-receptors in response to human odorants revealed their specific responses to the aldehyde human odorants. Taken together, the findings of this study not only provide exciting new insights into the human odorant detection of bed bugs, but also offer valuable information for developing new reagents (attractants or repellents) for the bed bug control.

  1. Uniqueness and Non-uniqueness in the Einstein Constraints

    CERN Document Server

    Pfeiffer, H P; Pfeiffer, Harald P.; York, James W.

    2005-01-01

    We examine numerically a sequence of free data for the conformal thin sandwich (CTS) equations representing non-linearly perturbed Minkowski spacetimes. We find only one solution for the standard (four) CTS equations; however, we find {\\em two} distinct solutions for the same free data when the lapse is determined by a fifth elliptic equation arising from specification of the time derivative of the mean curvature. For a given {\\em physical} (conformally scaled) amplitude of the perturbation, the solution for the physical data $g_{ij}, K_{ij}$ nevertheless appears to be unique.

  2. 高温气冷堆球床等效导热系数实验研究进展%Progress in Pebble Bed Heat Transfer Test Facility of High Temperature Gas-cooled Reactor

    Institute of Scientific and Technical Information of China (English)

    任成; 杨星团; 李聪新; 孙艳飞

    2013-01-01

    Pebble bed effective thermal conductivity of the reactor core is a vital parameter which directly affects the maximum temperature of fuel and the temperature distribution of reactor core in high temperature gas-cooled reactor and plays a dominant role in afterheat removal. The experimental research of pebble bed effective thermal conductivity is helpful for improving the reactor analytical program, increasing the power of single reactor and the safe analysis of projects. The experiments and results of pebble bed effective thermal conductivity measurement at home and abroad are reviewed. The develop direction is also discussed.%堆芯球床等效导热系数是直接影响高温气冷堆燃料最高温度和堆芯温度分布的关键参数;在余热导出过程中起主导作用.开展球床等效导热系数的实验研究对于反应堆分析程序的完善、研究提高高温气冷堆单堆功率的可能性、以及工程的安全分析具有重要的意义.综述了国内外球床等效导热系数测量的研究现状,给出了清华大学HTR-PM三维堆芯球床等效导热系数测量实验最新成果,总结了各国实验的研究手段,对研究方向进行了讨论.

  3. The influence of fine char particles burnout on bed agglomeration during the fluidized bed combustion of a biomass fuel

    Energy Technology Data Exchange (ETDEWEB)

    Scala, Fabrizio; Chirone, Riccardo [Istituto di Ricerche sulla Combustione, CNR, P.le V. Tecchio, 80-80125 Naples (Italy); Salatino, Piero [Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, P.le V. Tecchio, 80-80125 Naples (Italy)

    2003-11-15

    The combustion of biomass char in a bubbling fluidized bed is hereby addressed, with specific reference to the influence that the combustion of fine char particles may exert on ash deposition and bed agglomeration phenomena. Experiments of steady fluidized bed combustion (FBC) of powdered biomass were carried out with the aim of mimicking the postcombustion of attrited char fines generated in the fluidized bed combustion of coarse char. Experimental results showed that the char elutriation rate is much smaller than expected on the basis of the average size of the biomass powder and of the carbon loading in the combustor. Samples of bed material collected after prolonged operation of the combustor were characterized by scanning electron microscopy (SEM)-EDX analysis and revealed the formation of relatively coarse sand-ash-carbon aggregates. The phenomenology is consistent with the establishment of a char phase attached to the bed material as a consequence of adhesion of char fines onto the sand particles. Combustion under sound-assisted fluidization conditions was also tested. As expected, enhancement of fines adhesion on bed material and further reduction of the elutriation rate were observed. Experimental results are interpreted in the light of a simple model which accounts for elutriation of free fines, adhesion of free fines onto bed material and detachment of attached fines by attrition of char-sand aggregates. Combustion of both free and attached char fines is considered. The parameters of the model are assessed on the basis of the measured carbon loadings and elutriation rates. Model computations are directed to estimate the effective size and the peak temperature of char-sand aggregates. The theoretical estimates of the effective aggregate size match fairly well those observed in the experiments.

  4. Consequences for overcrowding in the emergency room of a change in bed management policy on available in-hospital beds.

    Science.gov (United States)

    Claret, Pierre-Géraud; Boudemaghe, Thierry; Bobbia, Xavier; Stowell, Andrew; Miard, Élodie; Sebbane, Mustapha; Landais, Paul; De La Coussaye, Jean-Emmanuel

    2015-10-19

    Objective Emergency rooms play an important role by providing continuous access to healthcare 24 h a day, 7 days a week, but the lack of available hospital beds has become a major difficulty. Changing bed management policy could improve patient flow. The aim of the present study was to evaluate the consequences of a change in patient prioritisation on available beds.Methods The study consisted of a computerised bed management simulation based on day-by-day data collected from 1 to 31 January 2013 in a teaching hospital. Real hospital data were used to power the computer simulation. The scenarios tested were: (1) priority for emergency and surgery; (2) priority for emergency and medicine; (3) priority for planned admissions and surgery; and (4) priority for planned admissions and medicine. The results of these scenarios were compared with each other and to actual data.Results This study included 2347 patients. The scenario that proved to be the least efficient was the one that gave priority to emergency patients presenting with a medical condition. The scenario that exhibited the best efficiency was the one that gave priority to planned admissions and surgery.Conclusions Changing policies for hospital bed management is worth exploring to improve hospital patient flow and length of stay.What is known about the topic? The lack of available hospital beds is a major difficulty in managing patient flow in emergency rooms (ERs). The ER patient flow competes against a flow of planned hospital admissions for the same beds and the lack of a clearly defined policy on either prioritising ER patient flow over planned admissions or vice versa contributes to a disordered system.What does this paper add? We compared several simulated scenarios corresponding to different bed management policies. The scenario that gave priority to planned admissions and surgery gave the most suitable results.What are the implications for practitioners? Postponing scheduled surgical patients was not

  5. Diffusion of bed load particles subject to different flow conditions

    Science.gov (United States)

    Cecchetto, Martina; Cotterle, Luca; Tregnaghi, Matteo; Tait, Simon; Marion, Andrea

    2015-04-01

    An in-depth understanding of sediment motion in rivers has acquired increasing importance lately in order to plan restoration activities that provide ecological benefit. River beds constitute the interfacial environment where several species live and mass exchange of sediments/nutrients/pollutants can take place. Moving grains interacting with the bed deposit and can locally change the bed surface topography they can also act as carriers for contaminants associated with the grains. Study the motion of grains on the bed, in particular the extent and variability of their travel distance with regards to the flow conditions can provide information on the transport of grain associated contaminants. The results of a series of experimental tests, in which increasing levels of boundary shear stress were applied over a bed deposit of natural river gravel, are reported. Image databases consisted of a series of bed images acquired at a frequency of 45 Hz were collected. Analysis of the images has provided time and position data to plot the trajectories of more than 200 moving grains for each test. This data enables the derivation of the statistics of the un-truncated probability distribution of the detected particles' step length, which is consider as the distance moved by a particle from the moment it is entrained to the instant it stops on the bed. In recent studies the movement of bed load material has been indicated as diffusive, but little is known about the spatial and temporal scales of this diffusion. The analysis of the longitudinal and transverse trajectories for the tracked particles has here revealed three regimes of diffusion: a ballistic diffusion which takes place at the very beginning of particles motion, an anomalous intermediate regime, and a normal subdiffusion which occurs for larger times. Characteristic time scales separate these three diffusive regimes. Results show that in experiments with higher shear stresses the time scale separating the ballistic

  6. A Simulated Level Loading of Supply and Demand for Beds in a Tertiary Care Children's Hospital Reduces Overall Bed Requirements.

    Science.gov (United States)

    Gangadharan, Sandeep; Belpanno, Brian

    2015-01-01

    Anticipating throughput and allocating resources effectively in children's hospitals have unique challenges relative to adult inpatient centers. The seasonal and daily variation can be difficult to anticipate in terms of impact and creating plans for adequate preparation. Discrete event simulation methodology can be helpful in determining appropriate allocation of resources and has been increasingly appropriated in health care from industry. A representative sample set was abstracted from the Cohen Children's Medical Center census tracking system to describe the present state. A larger data set was used to determine the appropriate level load. The total work performed each hour from 8 AM to 8 PM was evaluated against the level load plan of 11.5%. During the initial hours of the working period when the total work was low, more discharges were added. For each discharge added, an equal quantity of discharges was subtracted from the later hours of the day to bring the total work below 11.5% for each hour. Once the simulated state discharges were determined, a new aggregate bed supply line was created. These values were then added to the original visualization to show improvement. Our analysis suggests that a large part of the discharge/transfer activity and bed demand activity occurs in the pediatric intensive care unit in a roughly 4- to 5-hour window. Our simulation analysis suggests that level loading of this resource-intensive activity period has a potential to reduce bed occupancy, increase bed availability in peak bed demand times, and improve efficiency and throughput throughout the hospital. Discrete event simulation can be an effective tool for pediatric inpatient centers to determine appropriate allocation of resources to enhance patient safety and throughput without significant, costly expansion of bed capacity.

  7. Lithium nephropathy: unique sonographic findings.

    Science.gov (United States)

    Di Salvo, Donald N; Park, Joseph; Laing, Faye C

    2012-04-01

    This case series describes a unique sonographic appearance consisting of numerous microcysts and punctate echogenic foci seen on renal sonograms of 10 adult patients receiving chronic lithium therapy. Clinically, chronic renal insufficiency was present in 6 and nephrogenic diabetes insipidus in 2. Sonography showed numerous microcysts and punctate echogenic foci. Computed tomography in 5 patients confirmed microcysts and microcalcifications, which were fewer in number than on sonography. Magnetic resonance imaging in 2 patients confirmed microcysts in each case. Renal biopsy in 1 patient showed chronic interstitial nephritis, microcysts, and tubular dilatation. The diagnosis of lithium nephropathy should be considered when sonography shows these findings.

  8. Mucormycosis in India: unique features.

    Science.gov (United States)

    Chakrabarti, Arunaloke; Singh, Rachna

    2014-12-01

    Mucormycosis remains a devastating invasive fungal infection, with high mortality rates even after active management. The disease is being reported at an alarming frequency over the past decades from India. Indian mucormycosis has certain unique features. Rhino-orbito-cerebral presentation associated with uncontrolled diabetes is the predominant characteristic. Isolated renal mucormycosis has emerged as a new clinical entity. Apophysomyces elegans and Rhizopus homothallicus are emerging species in this region and uncommon agents such as Mucor irregularis and Thamnostylum lucknowense are also being reported. This review focuses on these distinct features of mucormycosis observed in India.

  9. UNIQUE ORAL DRUG DELIVERY SYSTEM

    Institute of Scientific and Technical Information of China (English)

    Raphael M. Ottenbrite; ZHAO Ruifeng; Sam Milstein

    1995-01-01

    An oral drug delivery system using proteinoid microspheres is discussed with respect to its unique dependence on pH. It has been found that certain drugs such as insulin and heparin can be encapsulated in proteinoid spheres at stomach pH's (1-3). These spheres also dissemble at intestinal pH's (6-7) releasing the drug for absorption. Using this technique low molecular weight heparin and human growth hormone have been orally delivered successfully to several animal species. Future work has been proposed to study the interaction and binding of the specific drugs with synthesized oligopeptides.

  10. Analysis of unique beta transitions

    DEFF Research Database (Denmark)

    Eman, B.; Krmpotic, F.; Tadic, D;

    1967-01-01

    The Heidelberg group measurements [For abstr. see Phys. Rev. Nucl. Sci. Vol. 15 (1965)] of unique forbidden transitions have been analysed. It has been found that experimental shape factors can be reproduced only with the induced pseudoscalar form factor d ...-non-conserving tensor form factor b > 0. In the former case they contradict Daniel's results [See abstr. 1966A10720] for 0- rarr 0+ transitions, whereas in the latter they are in disagreement with other known analyses of mu-meson capture, allowed and forbidden transitions. The conclusion appears to be independent...

  11. A Comparison of Tandem Walk Performance Between Bed Rest Subjects and Astronauts

    Science.gov (United States)

    Miller, Chris; Peters, Brian; Kofman, Igor; Philips, Tiffany; Batson, Crystal; Cerisano, Jody; Fisher, Elizabeth; Mulavara, Ajitkumar; Feiveson, Alan; Reschke, Millard; Bloomberg, Jacob

    2015-01-01

    Astronauts experience a microgravity environment during spaceflight, which results in a central reinterpretation of both vestibular and body axial-loading information by the sensorimotor system. Subjects in bed rest studies lie at 6deg head-down in strict bed rest to simulate the fluid shift and gravity-unloading of the microgravity environment. However, bed rest subjects still sense gravity in the vestibular organs. Therefore, bed rest isolates the axial-unloading component, thus allowing for the direct study of its effects. The Tandem Walk is a standard sensorimotor test of dynamic postural stability. In a previous abstract, we compared performance on a Tandem Walk test between bed rest control subjects, and short- and long-duration astronauts both before and after flight/bed rest using a composite index of performance, called the Tandem Walk Parameter (TWP), that takes into account speed, accuracy, and balance control. This new study extends the previous data set to include bed rest subjects who performed exercise countermeasures. The purpose of this study was to compare performance during the Tandem Walk test between bed rest subjects (with and without exercise), short-duration (Space Shuttle) crewmembers, and long-duration International Space Station (ISS) crewmembers at various time points during their recovery from bed rest or spaceflight.

  12. Efficacy of commercially available ultrasonic pest repellent devices to affect behavior of bed bugs (Hemiptera: Cimicidae).

    Science.gov (United States)

    Yturralde, K M; Hofstetter, R W

    2012-12-01

    Little is known about the potential for acoustic communication in bed bugs, Cimex lectularius L. (Hemiptera: Cimicidae), or the use of sound as cues in host location, although many hemipterans are known to communicate with sound. Most behavioral research has focused on bed bug pheromones that are used in aggregation and as alarm signals. We investigated the influence of sound as a deterrent and as an attractant, either of which could ultimately be used to monitor and control bed bugs. Female bed bugs were tested in two-choice tests with four different commercially available ultrasonic repellent devices. We found that female bed bugs were equally likely to occur in arenas with or without sound produced by ultrasonic devices. These devices did not repel or attract bed bugs during choice trials. However, more bed bugs preferred the middle corridor between the test (sound) and control (no sound) arenas when the sound devices were played. Bed bugs were also more likely to exit the middle corridor during control trials compared with treatment trials with ultrasonic devices. Our results confirm that commercial devices producing ultrasound are not a promising tool for repelling bed bugs.

  13. Laboratory rearing of bed bugs

    Science.gov (United States)

    The resurgence of bed bugs Cimex lectularius L. in the United States and worldwide has resulted in an increase in research by university, government, and industry scientists directed at the biology and control of this blood-sucking pest. A need has subsequently arisen for producing sufficient biolog...

  14. How to Find Bed Bugs

    Science.gov (United States)

    Find and correctly identify an infestation early before it becomes widespread. Look for rusty or reddish stains and pinpoint dark spots on bed sheets or mattresses, and search for bugs near the piping, seams and tags of the mattress and box spring.

  15. Water column and bed-sediment core samples collected from Brownlee Reservoir near Oxbow, Oregon, 2012

    Science.gov (United States)

    Fosness, Ryan L.; Naymik, Jesse; Hopkins, Candice B.; DeWild, John F.

    2013-01-01

    The U.S. Geological Survey, in cooperation with Idaho Power Company, collected water-column and bed-sediment core samples from eight sites in Brownlee Reservoir near Oxbow, Oregon, during May 5–7, 2012. Water-column and bed-sediment core samples were collected at each of the eight sites and analyzed for total mercury and methylmercury. Additional bed-sediment core samples, collected from three of the eight sites, were analyzed for pesticides and other organic compounds, trace metals, and physical characteristics, such as particle size. Total mercury and methylmercury were detected in each of the water column and bed-sediment core samples. Only 17 of the 417 unique pesticide and organic compounds were detected in bed-sediment core samples. Concentrations of most organic wastewater compounds detected in bed sediment were less than the reporting level. Trace metals detected were greater than the reporting level in all the bed-sediment core samples submitted for analysis. The particle size distribution of bed-sediment core samples was predominantly clay mixed with silt.

  16. Pressurized circulating fluidized bed combustion technology

    Energy Technology Data Exchange (ETDEWEB)

    Vasquez-Malebran, S.; Anglesea, W.T. [Fluent Europe Limited, Sheffield (United Kingdom)

    1998-12-31

    This report describes how the FLUENT computations fluid dynamics code has been provided with a granular (gas-solids), multiphase flow-modelling capability in order to simulate the operation of a circulating fluidized bed combustion chamber. The new multiphase module solves the conservation equations for each phase on an Eulerian basis and it currently enables gas phase reactions and interphase heat and momentum transfer to be modelled. Because of fundng restrictions, the module has not yet been provided with a general capability for modelling interphase mass transfer and therefore approximations have to be made when simulating coal combustion. Having developed the code and carried out basic testing, it has been used to simulate one set of conditions in the circulating fluidized bed combustion test facility operated by RWE Energie AG at Niederaussem Germany. Considering the simplifications made in this simulation, the level of agreement between the code results and the available measurements and observations is very encouraging. 18 refs., 5 figs., 2 tabs.

  17. Bed system performance in helium circulation mode

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yean Jin; Jung, Kwang Jin; Ahn, Do Hee; Chung, Hong Suk [UST, Daejeon (Korea, Republic of); Kang, Hee Suk [KAERI, Daejeon (Korea, Republic of); Yun, Sei Hun [NFRI, Deajeon (Korea, Republic of)

    2016-05-15

    As a part of the International Thermonuclear Experimental Reactor (ITER) Project, We have conducted an experiment for storing hydrogen to depleted uranium and zirconium cobalt. The helium blanket effect has been observed in experiments using metal hydrides. The collapse of the hydrogen isotopes are accompanied by the decay heat and helium-3. Helium-3 dramatically reduces the hydrogen isotope storage capacity by surrounding the metal. This phenomenon is called a helium blanket effect. In addition the authors are working on the recovery and removal techniques of helium-3. In this paper, we discuss the equipment used to test the helium blanket effect and the results of a helium circulation experiment. The helium-3 produced surrounds the storage material surface and thus disturbs the reaction of the storage material and the hydrogen isotope. Even if the amount of helium-3 is small, the storage capacity of the SDS bed significantly drops. This phenomenon is the helium blanket effect. To resolve this phenomenon, a circulating loop was introduced. Using a circulating system, helium can be separated from the storage material. We made a helium loop that includes a ZrCo bed. Then using a metal bellows pump, we tested the helium circulation.

  18. Pebble-bed pebble motion: Simulation and Applications

    Energy Technology Data Exchange (ETDEWEB)

    Joshua J. Cogliati; Abderrafi M. Ougouag

    2011-11-01

    Pebble bed reactors (PBR) have moving graphite fuel pebbles. This unique feature provides advantages, but also means that simulation of the reactor requires understanding the typical motion and location of the granular flow of pebbles. This report presents a method for simulation of motion of the pebbles in a PBR. A new mechanical motion simulator, PEBBLES, efficiently simulates the key elements of motion of the pebbles in a PBR. This model simulates gravitational force and contact forces including kinetic and true static friction. It's used for a variety of tasks including simulation of the effect of earthquakes on a PBR, calculation of packing fractions, Dancoff factors, pebble wear and the pebble force on the walls. The simulator includes a new differential static friction model for the varied geometries of PBRs. A new static friction benchmark was devised via analytically solving the mechanics equations to determine the minimum pebble-to-pebble friction and pebble-to-surface friction for a five pebble pyramid. This pyramid check as well as a comparison to the Janssen formula was used to test the new static friction equations. Because larger pebble bed simulations involve hundreds of thousands of pebbles and long periods of time, the PEBBLES code has been parallelized. PEBBLES runs on shared memory architectures and distributed memory architectures. For the shared memory architecture, the code uses a new O(n) lock-less parallel collision detection algorithm to determine which pebbles are likely to be in contact. The new collision detection algorithm improves on the traditional non-parallel O(n log(n)) collision detection algorithm. These features combine to form a fast parallel pebble motion simulation. The PEBBLES code provides new capabilities for understanding and optimizing PBRs. The PEBBLES code has provided the pebble motion data required to calculate the motion of pebbles during a simulated earthquake. The PEBBLES code provides the ability to

  19. Experimental Study on Coal Multi-generation in Dual Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    Fan Xiaoxu; Lu Qinggang; Na Yongjie; Liu Qi

    2007-01-01

    An atmospheric test system of dual fluidized beds for coal multi-generation was built. One bubbling fluidized bed is for gasification and a circulating fluidized bed for combustion. The two beds are combined with two valves:one valve to send high temperature ash from combustion bed to the gasification bed and another valve to send char and ash from gasification bed to combustion bed. Experiments on Shenhua coal multi-generation were made at temperatures from 1112 K to 1191 K in the dual fluidized beds. The temperatures of the combustor are stable and the char combustion efficiency is about 98%. Increasing air/coal ratio to the fluidized bed leads to the increase of temperature and gasification efficiency. The maximum gasification efficiency is 36.7% and the calorific value of fuel gas is 10.7 MJ/Nm3. The tar yield in this work is 1.5%, much lower than that of pyrolysis.Carbon conversion efficiency to fuel gas and flue gas is about 90%.

  20. Infestation by pyrethroids resistant bed bugs in the suburb of Paris, France

    Directory of Open Access Journals (Sweden)

    Durand R.

    2012-11-01

    Full Text Available Bed bugs are hematophagous insects responsible for a re-emerging and challenging indoor pest in many countries. Bed bugs infestations may have health consequences including nuisance biting, cutaneous and systemic reactions. This resurgence can probably be attributed to factors such as increased international travel and development of resistance against insecticides. Resistance against pyrethroids has been reported several times from the USA and rarely in Europe. In France, very few data on bed bugs are available. The present study aimed to assess the infestation by bed bugs of a complex of two high-rise apartment buildings in the suburb of Paris and to evaluate their susceptibility to pyrethroid insecticides. We inspected for bed bugs 192 out of 198 apartments units (97% and interviewed their residents. 76 (39.6% apartments were infested. Among the 97 residents living in infested apartments, 53 (54.6% reported bed bug bites. A total of 564 bed bugs were collected in the infested units. Bioassays showed that 54 out of 143 bed bugs were resistant to pyrethroids (37.8%; 95% confidence interval: 29.9-45.7%. DNA sequencing showed that all bed bugs tested (n = 124 had homozygous L925I kdr-like gene mutation. The level of pyrethroid resistance found indicates that this phenomenon was already established in the site and prompts the need to reevaluate the wide use of pyrethroids to control bed bugs.