WorldWideScience

Sample records for undiscovered technically recoverable

  1. Geology and assessment of the undiscovered, technically recoverable petroleum resources of Armenia, 2013

    Science.gov (United States)

    Klett, T.R.

    2016-02-23

    The U.S. Geological Survey (USGS) assessed the undiscovered, technically recoverable oil and gas resources of Armenia in 2013. A Paleozoic and a Cenozoic total petroleum system (TPS) were identified within the country of Armenia. The postulated petroleum system elements are uncertain, resulting in low geologic probabilities for significant oil an gas resources. Two assessment units (AU) were delineated in each TPS—a Paleozoic-Sourced Conventional Reservoirs AU and a Permian Shale Gas AU in the Paleozoic Composite TPS and a Paleogene-Sourced Conventional Reservoirs AU and a Cenozoic Coalbed Gas AU in the Cenozoic Composite TPS. The TPS elements are largely uncertain and risked, and so only the Paleogene-Sourced Conventional Reservoirs AU was quantitatively assessed because the geologic probability is more than the threshold of 10 percent (that is, the probability of at least one conventional oil or gas accumulation of 5 million barrels of oil equivalent or greater based on postulated petroleum-system elements). The USGS estimated fully risked mean volumes of about 1 million barrels of oil (MMBO), about 6 billion cubic feet of natural gas (BCFG), and less than 1 million barrels of natural gas liquids (MMBNGL).

  2. Assessment of undiscovered conventionally recoverable petroleum resources of the Arabian-Iranian Basin

    Science.gov (United States)

    Masters, Charles D.; Klemme, H. Douglas; Coury, Anny B.

    1982-01-01

    The estimates of undiscovered conventionally recoverable petroleum resources in the Arabian-Iranian basin at probability levels of 95 percent, 5 percent, and statistical mean are for oil (in billions of barrels): 72, 337, and 174; and for gas (in trillions of cubic feet): 299, 1792, and 849. The occurrence of petroleum can be accounted for in five definitive geological settings or plays. The assessment of undiscovered resource potential assumes that the new discoveries will expand the occurrence of petroleum in these basic plays; no additional plays with significant petroleum potential were recognized. The five plays listed by geologic age are: (I) Upper Cretaceous and Tertiary, (II) Lower and Middle Cretaceous sandstone, (III) Lower and Middle Cretaceous limestone, (IV) Jurassic, and (V) Permian. The Permian play, located in the south-central Arabian Gulf region and extending northeast-southwest from southern Iran to the Ar Rub' al Khali in Saudi Arabia, accounts for over four-fifths of the mean estimate of undiscovered gas. The remainder of the gas is divided about equally among the other four plays. The Jurassic play, located on the south side of the Arabian Gulf, accounts for slightly less than one-third of the estimated undiscovered oil, which is split equally between Saudi Arabia and Iraq. The Lower and Middle Cretaceous limestone play is located in the southern Gulf region and accounts for about one-fifth of the undiscovered oil, most of which is located in Saudi Arabia and the remainder in the United Arab Emirates. The Lower and Middle Cretaceous sandstone play is centralized in Kuwait at the head of the Arabian Gulf with significant potential extending to the northwest in Iraq; the play accounts for about one-third of the undiscovered oil, the great majority of which is estimated to be in Iraq with the remainder divided between Saudi Arabia and Kuwait. The upper Cretaceous-Tertiary play is located in the Zagros fold belt of Iran and Iraq and accounts for

  3. Assessment of undiscovered conventionally recoverable petroleum resources of the Northwest European region

    Science.gov (United States)

    Masters, Charles D.; Klemme, H. Douglas

    1984-01-01

    The estimates of undiscovered conventionally recoverable petroleum resources in the northwest European region at probability levels of 95 percent, 5 percent, statistical mean, and mode are for oil (in billions of barrels): 9, 34, 20, and 15; and for gas (in trillions of cubic feet): 92, 258, 167, and 162. The occurrence of petroleum can be accounted for in two distinct geological plays located in the various subbasins of the region. Play I is associated with the distribution of mature source rocks of Late Jurassic age relative to four distinct trapping conditions. The play has been demonstrated productive mostly in the Viking and Central Grabens of the North Sea, where the shale has been buried to optimum depths for the generation of both oil and gas. To the north of 62 ? N. latitude up to the Barents Sea, source rocks become increasingly deeply buried and are interpreted to be dominantly gas prone; a narrow band of potentially oil-prone shales tracks most of the coast of Norway, but water depths in favorable localities commonly range from 600 to 1,200 feet. To the south of the Central Graben, the Jurassic source rocks are either immature or minimally productive because of a change in facies. Undrilled traps remain within the favorable source-rock area, and exploration will continue to challenge the boundaries of conventional wisdom, especially on the Norwegian side where little has .been reported on the geology of the adjoining Bergen High or Horda Basin, though, reportedly, the Jurassic source rocks are missing on the high and are immature in the southern part of the basin. Play II is associated with the distribution of a coal facies of Carboniferous age that is mature for the generation of gas and locally underlies favorable reservoir and sealing rocks. The play is limited largely by facies development to the present area of discovery and production but is limited as well to the southeast into onshore Netherlands and Germany by the unfavorable economics of an

  4. Assessment of Undiscovered Oil and Gas Resources of the Red Sea Basin Province

    Science.gov (United States)

    ,

    2010-01-01

    The U.S. Geological Survey estimated mean volumes of 5 billion barrels of undiscovered technically recoverable oil and 112 trillion cubic feet of recoverable gas in the Red Sea Basin Province using a geology-based assessment methodology.

  5. Assessment of undiscovered oil and gas resources in the Cuyo Basin Province, Argentina, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Brownfield, Michael E.; Tennyson, Marilyn E.; Le, Phuong A.; Mercier, Tracey J.; Finn, Thomas M.; Hawkins, Sarah J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Klett, Timothy R.; Leathers-Miller, Heidi M.; Woodall, Cheryl A.

    2017-07-18

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 236 million barrels of oil and 112 billion cubic feet of associated gas in the Cuyo Basin Province, Argentina.

  6. Assessment of undiscovered oil and gas resources in the North-Central Montana Province, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Mercier, Tracey J.; Brownfield, Michael E.; Tennyson, Marilyn E.; Woodall, Cheryl A.; Le, Phuong A.; Klett, Timothy R.; Gaswirth, Stephanie B.; Finn, Thomas M.; Pitman, Janet K.; Marra, Kristen R.; Leathers-Miller, Heidi M.

    2018-02-12

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 55 million barrels of oil and 846 billion cubic feet of gas in the North-Central Montana Province.

  7. Assessment of undiscovered continuous gas resources in Upper Devonian Shales of the Appalachian Basin Province, 2017

    Science.gov (United States)

    Enomoto, Catherine B.; Trippi, Michael H.; Higley, Debra K.; Rouse, William A.; Dulong, Frank T.; Klett, Timothy R.; Mercier, Tracey J.; Brownfield, Michael E.; Leathers-Miller, Heidi M.; Finn, Thomas M.; Marra, Kristen R.; Le, Phuong A.; Woodall, Cheryl A.; Schenk, Christopher J.

    2018-04-19

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 10.7 trillion cubic feet of natural gas in Upper Devonian shales of the Appalachian Basin Province.

  8. Assessment of undiscovered oil and gas resources in the Lower Indus Basin, Pakistan, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Klett, Timothy R.; Finn, Thomas M.; Mercier, Tracey J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Le, Phuong A.; Hawkins, Sarah J.; Leathers-Miller, Heidi M.

    2017-09-19

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 164 million barrels of oil and 24.6 trillion cubic feet of gas in the Lower Indus Basin, Pakistan.

  9. Assessment of undiscovered oil and gas resources of the Susitna Basin, southern Alaska, 2017

    Science.gov (United States)

    Stanley, Richard G.; Potter, Christopher J.; Lewis, Kristen A.; Lillis, Paul G.; Shah, Anjana K.; Haeussler, Peter J.; Phillips, Jeffrey D.; Valin, Zenon C.; Schenk, Christopher J.; Klett, Timothy R.; Brownfield, Michael E.; Drake II, Ronald M.; Finn, Thomas M.; Haines, Seth S.; Higley, Debra K.; Houseknecht, David W.; Le, Phuong A.; Marra, Kristen R.; Mercier, Tracey J.; Leathers-Miller, Heidi M.; Paxton, Stanley T.; Pearson, Ofori N.; Tennyson, Marilyn E.; Woodall, Cheryl A.; Zyrianova, Margarita V.

    2018-05-01

    The U.S. Geological Survey (USGS) recently completed an assessment of undiscovered, technically recoverable oil and gas resources in the Susitna Basin of southern Alaska. Using a geology-based methodology, the USGS estimates that mean undiscovered volumes of about 2 million barrels of oil and nearly 1.7 trillion cubic feet of gas may be found in this area.

  10. Assessment of undiscovered continuous oil and gas resources in the Bohaiwan Basin Province, China, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Mercier, Tracey J.; Woodall, Cheryl A.; Finn, Thomas M.; Brownfield, Michael E.; Le, Phuong A.; Klett, Timothy R.; Gaswirth, Stephanie B.; Marra, Kristen R.; Leathers-Miller, Heidi M.; Potter, Christopher J.

    2018-02-07

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 2.0 billion barrels of oil and 20.3 trillion cubic feet of gas in the Bohaiwan Basin Province, China.

  11. Assessment of undiscovered oil and gas resources in the Canning Basin Province, Australia, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Mercier, Tracey J.; Woodall, Cheryl A.; Finn, Thomas M.; Le, Phuong A.; Brownfield, Michael E.; Gaswirth, Stephanie B.; Marra, Kristen R.; Leathers-Miller, Heidi M.

    2018-05-31

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 1.3 billion barrels of oil and 34.4 trillion cubic feet of gas in the Canning Basin Province of Australia.

  12. Assessment of undiscovered conventional and continuous oil and gas resources of the Baltic Depression Province, 2014

    Science.gov (United States)

    Brownfield, Michael E.; Schenk, Christopher J.; Charpentier, Ronald R.; Klett, Timothy R.; Pitman, Janet K.; Tennyson, Marilyn E.; Gaswirth, Stephanie B.; Mercier, Tracey J.; Le, Phuong A.; Leathers, Heidi M.

    2015-01-01

    The U.S. Geological Survey estimated mean volumes of undiscovered, technically recoverable resources of 282 million barrels of conventional oil, 576 billion cubic feet of conventional gas, 1.3 billion barrels of continuous oil, and 4.6 trillion cubic feet of shale gas in the Baltic Depression Province.

  13. Assessment of undiscovered conventional oil and gas resources in the Wyoming Thrust Belt Province, Wyoming, Idaho, and Utah, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Mercier, Tracey J.; Tennyson, Marilyn E.; Woodall, Cheryl A.; Brownfield, Michael E.; Le, Phuong A.; Klett, Timothy R.; Gaswirth, Stephanie B.; Finn, Thomas M.; Marra, Kristen R.; Leathers-Miller, Heidi M.

    2018-02-16

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 26 million barrels of oil and 700 billion cubic feet of gas in the Wyoming Thrust Belt Province, Wyoming, Idaho, and Utah.

  14. Assessment of undiscovered continuous oil and gas resources of Upper Cretaceous Shales in the Songliao Basin of China, 2017

    Science.gov (United States)

    Potter, Christopher J.; Schenk, Christopher J.; Pitman, Janet K.; Klett, Timothy R.; Tennyson, Marilyn E.; Gaswirth, Stephanie B.; Leathers-Miller, Heidi M.; Finn, Thomas M.; Brownfield, Michael E.; Mercier, Tracey J.; Marra, Kristen R.; Woodall, Cheryl A.

    2018-05-03

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 3.3 billion barrels of oil and 887 billion cubic feet of gas in shale reservoirs of the Upper Cretaceous Qingshankou and Nenjiang Formations in the Songliao Basin of northeastern China.

  15. Assessment of undiscovered oil and gas resources of the Volga-Ural Region Province, Russia and Kazakhstan, 2010

    Science.gov (United States)

    Klett, T.R.; Schenk, Christopher J.; Charpentier, Ronald R.; Brownfield, Michael E.; Pitman, Janet K.; Cook, Troy A.; Tennyson, Marilyn E.

    2010-01-01

    The U.S. Geological Survey estimated mean volumes of technically recoverable, conventional, undiscovered petroleum resources at 1.4 billion barrels of crude oil, 2.4 trillion cubic feet of natural gas, and 85 million barrels of natural gas liquids for the Volga-Ural Region Province, using a geology-based assessment methodology.

  16. Assessment of undiscovered continuous gas resources in the Amu Darya Basin Province of Turkmenistan, Uzbekistan, Iran, and Afghanistan, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Mercier, Tracey J.; Hawkins, Sarah J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Klett, Timothy R.; Le, Phuong A.; Brownfield, Michael E.; Woodall, Cheryl A.

    2017-08-17

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 35.1 trillion cubic feet of gas in the Amu Darya Basin Province of Turkmenistan, Uzbekistan, Iran, and Afghanistan.

  17. Assessment of undiscovered continuous oil and gas resources in the Heath Formation, central Montana and western North Dakota, 2016

    Science.gov (United States)

    Drake, Ronald M.; Schenk, Christopher J.; Klett, Timothy R.; Le, Phuong A.; Leathers, Heidi M.; Brownfield, Michael E.; Finn, Thomas M.; Gaswirth, Stephanie B.; Marra, Kristen R.; Tennyson, Marilyn E.

    2017-06-07

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated undiscovered, technically recoverable mean resources of 884 million barrels of oil and 106 billion cubic feet of gas in the North-Central Montana and Williston Basin Provinces of central Montana and western North Dakota.

  18. Geology and assessment of undiscovered oil and gas resources of the Zyryanka Basin Province, 2008

    Science.gov (United States)

    Klett, Timothy; Pitman, Janet K.; Moore, T.E.; Gautier, D.L.

    2017-11-22

    The U.S. Geological Survey (USGS) recently assessed the potential for undiscovered oil and gas resources of the Zyryanka Basin Province as part of the 2008 USGS Circum-Arctic Resource Appraisal program. The province is in the Russian Federation and is situated on the Omolon superterrane of the Kolyma block. The one assessment unit (AU) that was defined for this study, called the Zyryanka Basin AU, which coincides with the province, was assessed for undiscovered, technically recoverable, conventional resources. The estimated mean volumes of undiscovered resources in the Zyryanka Basin Province are ~72 million barrels of crude oil, 2,282 billion cubic feet of natural gas, and 61 million barrels of natural-gas liquids. About 66 percent of the study area and undiscovered petroleum resources are north of the Arctic Circle.

  19. Assessment of undiscovered continuous oil and gas resources in the Domanik-type formations of the Volga-Ural Region Province, Russia, 2017

    Science.gov (United States)

    Klett, Timothy R.; Brownfield, Michael E.; Finn, Thomas M.; Gaswirth, Stephanie B.; Le, Phuong A.; Leathers-Miller, Heidi M.; Marra, Kristen R.; Mercier, Tracey J.; Pitman, Janet K.; Schenk, Christopher J.; Tennyson, Marilyn E.; Woodall, Cheryl A.

    2018-02-27

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 2.8 billion barrels of oil and 34 trillion cubic feet of gas in the Domanik-type formations of the Volga-Ural Region Province, Russia.

  20. Assessment of undiscovered conventional oil and gas resources in the West Korea Bay–North Yellow Sea Basin, North Korea and China, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Mercier, Tracey J.; Hawkins, Sarah J.; Finn, Thomas M.; Gaswirth, Stephanie B.; Marra, Kristen R.; Klett, Timothy R.; Le, Phuong A.; Leathers-Miller, Heidi M.; Woodall, Cheryl A.

    2017-07-11

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable conventional resources of 1.1 billion barrels of oil and 2.2 trillion cubic feet of gas in the West Korea Bay–North Yellow Sea Basin, North Korea and China.

  1. Assessment of undiscovered oil and gas resources in the Cretaceous Nanushuk and Torok Formations, Alaska North Slope, and summary of resource potential of the National Petroleum Reserve in Alaska, 2017

    Science.gov (United States)

    Houseknecht, David W.; Lease, Richard O.; Schenk, Christopher J.; Mercier, Tracey J.; Rouse, William A.; Jarboe, Palma B.; Whidden, Katherine J.; Garrity, Christopher P.; Lewis, Kristen A.; Heller, Samuel; Craddock, William H.; Klett, Timothy R.; Le, Phuong A.; Smith, Rebecca; Tennyson, Marilyn E.; Gaswirth, Stephanie B.; Woodall, Cheryl A.; Brownfield, Michael E.; Leathers-Miller, Heidi M.; Finn, Thomas M.

    2017-12-22

    The U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 8.7 billion barrels of oil and 25 trillion cubic feet of natural gas (associated and nonassociated) in conventional accumulations in the Cretaceous Nanushuk and Torok Formations in the National Petroleum Reserve in Alaska, adjacent State and Native lands, and State waters. The estimated undiscovered oil resources in the Nanushuk and Torok Formations are significantly higher than previous estimates, owing primarily to recent, larger than anticipated oil discoveries.

  2. Geology and assessment of undiscovered oil and gas resources of the Laptev Sea Shelf Province, 2008

    Science.gov (United States)

    Klett, Timothy; Pitman, Janet K.; Moore, Thomas E.; Gautier, Donald L.

    2017-12-21

    The U.S. Geological Survey (USGS) recently assessed the potential for undiscovered oil and gas resources of the Laptev Sea Shelf Province as part of the 2008 Circum-Arctic Resource Appraisal (CARA) program. The province is situated in the Russian Federation and is located between the Taimyr Peninsula and the Novosibirsk (New Siberian) Islands. Three assessment units (AUs) were defined for this study: the West Laptev Grabens AU, the East Laptev Horsts AU, and the Anisin-Novosibirsk AU, two of which were assessed for undiscovered, technically recoverable resources. The East Laptev Horsts AU was not quantitatively assessed. The estimated mean volumes of undiscovered oil and gas for the Laptev Sea Shelf Province are approximately 3 billion barrels of crude oil, 32 trillion cubic feet of natural gas, and <1 billion barrels of natural gas liquids, all north of the Arctic Circle.

  3. Feasibility study of a pressure fed engine for a water recoverable space shuttle booster Volume 2: Technical, phase A effort

    Science.gov (United States)

    1972-01-01

    Design and systems considerations are presented on an engine concept selection for further preliminary design and program evaluation. These data have been prepared from a feasibility study of a pressure-fed engine for the water recoverable space shuttle booster.

  4. U.S. Geological Survey 2011 assessment of undiscovered oil and gas resources of the Cook Inlet region, south-central Alaska

    Science.gov (United States)

    Stanley, Richard G.; Pierce, Brenda S.; Houseknecht, David W.

    2011-01-01

    The U.S. Geological Survey (USGS) has completed an assessment of the volumes of undiscovered, technically recoverable oil and gas resources in conventional and continuous accumulations in Cook Inlet. The assessment used a geology-based methodology and results from new scientific research by the USGS and the State of Alaska, Department of Natural Resources, Division of Geological and Geophysical Surveys and Division of Oil and Gas (DOG). In the Cook Inlet region, the USGS estimates mean undiscovered volumes of nearly 600 million barrels of oil, about 19 trillion cubic feet of gas, and about 46 million barrels of natural gas liquids.

  5. Geology and assessment of undiscovered oil and gas resources of the North Kara Basins and Platforms Province, 2008

    Science.gov (United States)

    Klett, Timothy R.; Pitman, Janet K.; Moore, T.E.; Gautier, D.L.

    2017-11-15

    The U.S. Geological Survey (USGS) recently assessed the potential for undiscovered oil and gas resources of the North Kara Basins and Platforms Province as part of the its Circum-Arctic Resource Appraisal. This geologic province is north of western Siberia, Russian Federation, in the North Kara Sea between Novaya Zemlya to the west and Severnaya Zemlya to the east. One assessment unit (AU) was defined, the North Kara Basins and Platforms AU, which coincides with the geologic province. This AU was assessed for undiscovered, technically recoverable resources. The total estimated mean volumes of undiscovered petroleum resources in the province are ~1.8 billion barrels of crude oil, ~15.0 trillion cubic feet of natural gas, and ~0.4 billion barrels of natural-gas liquids, all north of the Arctic Circle.

  6. Geology and assessment of undiscovered oil and gas resources of the Lena-Vilyui Basin Province, 2008

    Science.gov (United States)

    Klett, Timothy; Pitman, Janet K.; Moore, T.E.; Gautier, D.L.

    2017-11-22

    The U.S. Geological Survey (USGS) recently assessed the potential for undiscovered oil and gas resources of the Lena-Vilyui Basin Province, north of the Arctic Circle, as part of the Circum-Arctic Resource Appraisal program. The province is in the Russian Federation and is situated between the Verkhoyansk fold-and-thrust belt and the Siberian craton. The one assessment unit (AU) defined for this study—the Northern Priverkhoyansk Foredeep AU—was assessed for undiscovered, technically recoverable resources. The estimated mean volumes of undiscovered resources for the Northern Priverkhoyansk Foredeep in the Lena-Vilyui Basin Province are ~400 million barrels of crude oil, 1.3 trillion cubic feet of natural gas, and 40 million barrels of natural-gas liquids, practically all (99.49 percent) of which is north of the Arctic Circle.

  7. Assessment of undiscovered oil and gas resources of the Cretaceous-Tertiary Composite Total Petroleum System, Taranaki Basin Assessment Unit, New Zealand

    Science.gov (United States)

    Wandrey, Craig J.; Schenk, Christopher J.; Klett, Timothy R.; Brownfield, Michael E.; Charpentier, Ronald R.; Cook, Troy A.; Pollastro, Richard M.; Tennyson, Marilyn E.

    2013-01-01

    The Cretaceous-Tertiary Composite Total Petroleum System coincident Taranaki Basin Assessment Unit was recently assessed for undiscovered technically recoverable oil, natural gas, and natural gas liquids resources as part of the U.S. Geological Survey (USGS) World Energy Resources Project, World Oil and Gas Assessment. Using a geology-based assessment methodology, the USGS estimated mean volumes of 487 million barrels of oil, 9.8 trillion cubic feet of gas, and 408 million barrels of natural gas liquids.

  8. Assessment of undiscovered oil and gas resources of the Central Burma Basin and the Irrawaddy-Andaman and Indo-Burman Geologic Provinces, Myanmar

    Science.gov (United States)

    Wandrey, Craig J.; Schenk, Christopher J.; Klett, Timothy R.; Brownfield, Michael E.; Charpentier, Ronald R.; Cook, Troy A.; Pollastro, Richard M.; Tennyson, Marilyn E.

    2012-01-01

    The Irrawaddy-Andaman and Indo-Burman Geologic Provinces were recently assessed for undiscovered technically recoverable oil, natural gas, and natural gas liquids resources as part of the U.S. Geological Survey's (USGS) World Oil and Gas Assessment. Using a geology-based assessment methodology, the USGS estimated mean volumes of 2.3 billion barrels of oil, 79.6 trillion cubic feet of gas, and 2.1 billion barrels of natrual gas liquids.

  9. Economics of Undiscovered Oil and Gas in the North Slope of Alaska: Economic Update and Synthesis

    Science.gov (United States)

    Attanasi, E.D.; Freeman, P.A.

    2009-01-01

    The U.S. Geological Survey (USGS) has published assessments by geologists of undiscovered conventional oil and gas accumulations in the North Slope of Alaska; these assessments contain a set of scientifically based estimates of undiscovered, technically recoverable quantities of oil and gas in discrete oil and gas accumulations that can be produced with conventional recovery technology. The assessments do not incorporate economic factors such as recovery costs and product prices. The assessors considered undiscovered conventional oil and gas resources in four areas of the North Slope: (1) the central North Slope, (2) the National Petroleum Reserve in Alaska (NPRA), (3) the 1002 Area of the Arctic National Wildlife Refuge (ANWR), and (4) the area west of the NPRA, called in this report the 'western North Slope'. These analyses were prepared at different times with various minimum assessed oil and gas accumulation sizes and with slightly different assumptions. Results of these past studies were recently supplemented with information by the assessment geologists that allowed adjustments for uniform minimum assessed accumulation sizes and a consistent set of assumptions. The effort permitted the statistical aggregation of the assessments of the four areas composing the study area. This economic analysis is based on undiscovered assessed accumulation distributions represented by the four-area aggregation and incorporates updates of costs and technological and fiscal assumptions used in the initial economic analysis that accompanied the geologic assessment of each study area.

  10. Geology and assessment of undiscovered oil and gas resources of the Hope Basin Province, 2008

    Science.gov (United States)

    Bird, Kenneth J.; Houseknecht, David W.; Pitman, Janet K.; Moore, Thomas E.; Gautier, Donald L.

    2018-01-04

    The Hope Basin, an independent petroleum province that lies mostly offshore in the southern Chukchi Sea north of the Chukotka and Seward Peninsulas and south of Wrangel Island, the Herald Arch, and the Lisburne Peninsula, is the largest in a series of postorogenic (successor) basins in the East Siberian-Chukchi Sea region and the only one with exploratory-well control and extensive seismic coverage.In spite of the seismic coverage and well data, the petroleum potential of the Hope Basin Province is poorly known. The adequacy of hydrocarbon charge, in combination with uncertainties in source-rock potential and maturation, was the greatest risk in this assessment. A single assessment unit was defined and assessed, resulting in mean estimates of undiscovered, technically recoverable resources that include ~3 million barrels of oil and 650 billion cubic feet of nonassociated gas.

  11. Geology and assessment of undiscovered oil and gas resources of the West Greenland-East Canada Province, 2008

    Science.gov (United States)

    Schenk, Christopher J.; Moore, Thomas E.; Gautier, Donald L.

    2018-01-05

    The U.S. Geological Survey (USGS) recently assessed the potential for undiscovered oil and gas resources of the West Greenland-East Canada Province as part of the USGS Circum-Arctic Resource Appraisal program. The province lies in the offshore area between western Greenland and eastern Canada and includes Baffin Bay, Davis Strait, Lancaster Sound, and Nares Strait west of, and including, part of Kane Basin. A series of major tectonic events led to the formation of several distinct structural domains that are the geologic basis for defining five assessment units (AU ) in the province, all of which are within the Mesozoic-Cenozoic Composite Total Petroleum System (TPS). Potential petroleum source rocks within the TPS include strata of Ordovician, Lower and Upper Cretaceous, and Paleogene ages. The five AUs defined for this study—the Eurekan Structures AU, Northwest Greenland Rifted Margin AU, Northeast Canada Rifted Margin AU, Baffin Bay Basin AU, and the Greater Ungava Fault Zone AU— encompass the entire province and were assessed for undiscovered, technically recoverable resources. The estimated mean volumes of undiscovered resources for the West GreenlandEast Canada Province are 10.7 billion barrels of oil, 75 trillion cubic feet of gas, and 1.7 billion barrels of natural gas liquids. For the part of the province that is north of the Arctic Circle, the estimated mean volumes of these undiscovered resources are 7.3 billion barrels of oil, 52 trillion cubic feet of natural gas, and 1.1 billion barrels of natural-gas liquids.

  12. Magnetically recoverable nanocatalysts

    KAUST Repository

    Polshettiwar, Vivek

    2011-05-11

    A broad overview on magnetically recoverable nanocatalysts is presented and the use of magnetic nanomaterials as catalysts is discussed. Magnetic materials are used as organocatalysts and their applications range to challenging reactions, such as hydroformylation and olefin metathesis. Magnetic nanomaterials are also being used in environmental applications, such as for photo- and biocatalysis and for the adsorption and removal of pollutants from air and water. These materials show great promise as enantioselective catalysts, which are used extensively for the synthesis of medicines, drugs, and other bioactive molecules. By functionalizing these materials using chiral ligands, a series of chiral nanocatalysts can be designed, offering great potential to reuse these otherwise expensive catalyst systems. Characterization of magnetic catalysts is often a challenging task, and NMR characterization of these catalysts is difficult because the magnetic nature of the materials interferes with the magnetic field of the spectrometer.

  13. Magnetically recoverable nanocatalysts

    KAUST Repository

    Polshettiwar, Vivek; Luque, Rafael L.; Fihri, Aziz; Zhu, Haibo; Bouhrara, Mohamed; Basset, Jean-Marie

    2011-01-01

    A broad overview on magnetically recoverable nanocatalysts is presented and the use of magnetic nanomaterials as catalysts is discussed. Magnetic materials are used as organocatalysts and their applications range to challenging reactions, such as hydroformylation and olefin metathesis. Magnetic nanomaterials are also being used in environmental applications, such as for photo- and biocatalysis and for the adsorption and removal of pollutants from air and water. These materials show great promise as enantioselective catalysts, which are used extensively for the synthesis of medicines, drugs, and other bioactive molecules. By functionalizing these materials using chiral ligands, a series of chiral nanocatalysts can be designed, offering great potential to reuse these otherwise expensive catalyst systems. Characterization of magnetic catalysts is often a challenging task, and NMR characterization of these catalysts is difficult because the magnetic nature of the materials interferes with the magnetic field of the spectrometer.

  14. Geologic assessment of undiscovered oil and gas resources in Aptian carbonates, onshore northern Gulf of Mexico Basin, United States

    Science.gov (United States)

    Hackley, Paul C.; Karlsen, Alexander W.

    2014-01-01

    Carbonate lithofacies of the Lower Cretaceous Sligo Formation and James Limestone were regionally evaluated using established U.S. Geological Survey (USGS) assessment methodology for undiscovered conventional hydrocarbon resources. The assessed area is within the Upper Jurassic–Cretaceous–Tertiary Composite total petroleum system, which was defined for the assessment. Hydrocarbons reservoired in carbonate platform Sligo-James oil and gas accumulations are interpreted to originate primarily from the Jurassic Smackover Formation. Emplacement of hydrocarbons occurred via vertical migration along fault systems; long-range lateral migration also may have occurred in some locations. Primary reservoir facies include porous patch reefs developed over paleostructural salt highs, carbonate shoals, and stacked linear reefs at the carbonate shelf margin. Hydrocarbon traps dominantly are combination structural-stratigraphic. Sealing lithologies include micrite, calcareous shale, and argillaceous lime mudstone. A geologic model, supported by discovery history analysis of petroleum geology data, was used to define a single regional assessment unit (AU) for conventional reservoirs in carbonate facies of the Sligo Formation and James Limestone. The AU is formally entitled Sligo-James Carbonate Platform Oil and Gas (50490121). A fully risked mean undiscovered technically recoverable resource in the AU of 50 million barrels of oil (MMBO), 791 billion cubic feet of natural gas (BCFG), and 26 million barrels of natural gas liquids was estimated. Substantial new development through horizontal drilling has occurred since the time of this assessment (2010), resulting in cumulative production of >200 BCFG and >1 MMBO.

  15. U.S. Geological Survey 2013 assessment of undiscovered resources in the Bakken and Three Forks Formations of the U.S. Williston Basin Province

    Science.gov (United States)

    Gaswirth, Stephanie B.; Marra, Kristen R.

    2014-01-01

    The Upper Devonian Three Forks and Upper Devonian to Lower Mississippian Bakken Formations comprise a major United States continuous oil resource. Current exploitation of oil is from horizontal drilling and hydraulic fracturing of the Middle Member of the Bakken and upper Three Forks, with ongoing exploration of the lower Three Forks, and the Upper, Lower, and Pronghorn Members of the Bakken Formation. In 2008, the U.S. Geological Survey (USGS) estimated a mean of 3.65 billion bbl of undiscovered, technically recoverable oil resource within the Bakken Formation. The USGS recently reassessed the Bakken Formation, which included an assessment of the underlying Three Forks Formation. The Pronghorn Member of the Bakken Formation, where present, was included as part of the Three Forks assessment due to probable fluid communication between reservoirs. For the Bakken Formation, five continuous and one conventional assessment units (AUs) were defined. These AUs are modified from the 2008 AU boundaries to incorporate expanded geologic and production information. The Three Forks Formation was defined with one continuous and one conventional AU. Within the continuous AUs, optimal regions of hydrocarbon recovery, or “sweet spots,” were delineated and estimated ultimate recoveries were calculated for each continuous AU. Resulting undiscovered, technically recoverable resource estimates were 3.65 billion bbl for the five Bakken continuous oil AUs and 3.73 billion bbl for the Three Forks Continuous Oil AU, generating a total mean resource estimate of 7.38 billion bbl. The two conventional AUs are hypothetical and represent a negligible component of the total estimated resource (8 million barrels of oil).

  16. Assessment of undiscovered oil and gas resources in the Ventura Basin Province, California, 2016

    Science.gov (United States)

    Tennyson, Marilyn E.; Schenk, Christopher J.; Pitman, Janet K.; Lillis, Paul G.; Klett, Timothy R.; Brownfield, Michael E.; Finn, Thomas M.; Gaswirth, Stephanie B.; Hawkins, Sarah J.; Marra, Kristen R.; Mercier, Tracey J.; Le, Phuong A.; Leathers-Miller, Heidi M.

    2017-10-02

    The U.S. Geological Survey (USGS) completed a geology-based assessment of undiscovered, technically recoverable conventional and continuous oil and gas resources in the part of the Ventura Basin Province that lies onshore or within State waters (within 3 miles of the shoreline) of California (fig. 1). Conventional oil and gas resources are those that have migrated upward into structural or stratigraphic traps from deep zones where the oil and gas is generated; water is present below the oil or gas. Continuous accumulations, in contrast, are those in which oil or gas is pervasively present in essentially all wells that penetrate them, that may not be structurally or stratigraphically trapped, and that typically lack oil-water or gas-water contacts. They are commonly produced with well-stimulation technology, such as hydraulic fracturing, referred to as “unconventional.” The same stimulation technology, however, is also used in many conventionally trapped accumulations. We estimated both the likely range of oil and gas volumes remaining to be discovered in accumulations similar to existing conventional oil and gas fields in the Ventura Basin Province (previously assessed by Keller [1995] as 1,060 million barrels of oil [MMBO], 1,900 billion cubic feet of gas [BCFG], and 60 million barrels of natural gas liquids [MMBNGL]), and the potential for oil and gas that might be present in a continuous accumulation at extreme depth in the floor of the basin.

  17. Geology and Assessment of Undiscovered Oil and Gas Resources of the East Barents Basins Province and the Novaya Zemlya Basins and Admiralty Arch Province, 2008

    Science.gov (United States)

    Klett, Timothy R.; Moore, Thomas E.; Gautier, D.L.

    2017-11-15

    The U.S. Geological Survey (USGS) recently assessed the potential for undiscovered petroleum resources of the East Barents Basins Province and the Novaya Zemlya Basins and Admiralty Arch Province as part of its Circum-Arctic Resource Appraisal. These two provinces are situated northeast of Scandinavia and the northwestern Russian Federation, on the Barents Sea Shelf between Novaya Zemlya to the east and the Barents Platform to the west. Three assessment units (AUs) were defined in the East Barents Basins Province for this study: the Kolguyev Terrace AU, the South Barents and Ludlov Saddle AU, and the North Barents Basin AU. A fourth AU, defined as the Novaya Zemlya Basins and Admiralty Arch AU, coincides with the Novaya Zemlya Basins and Admiralty Arch Province. These four AUs, all lying north of the Arctic Circle, were assessed for undiscovered, technically recoverable resources, resulting in total estimated mean volumes of ~7.4 billion barrels of crude oil, 318 trillion cubic feet (TCF) of natural gas, and 1.4 billion barrels of natural-gas liquids.

  18. Geologic assessment of undiscovered conventional oil and gas resources in the Lower Paleogene Midway and Wilcox Groups, and the Carrizo Sand of the Claiborne Group, of the Northern Gulf coast region

    Science.gov (United States)

    Warwick, Peter D.

    2017-09-27

    The U.S. Geological Survey (USGS) recently conducted an assessment of the undiscovered, technically recoverable oil and gas potential of Tertiary strata underlying the onshore areas and State waters of the northern Gulf of Mexico coastal region. The assessment was based on a number of geologic elements including an evaluation of hydrocarbon source rocks, suitable reservoir rocks, and hydrocarbon traps in an Upper Jurassic-Cretaceous-Tertiary Composite Total Petroleum System defined for the region by the USGS. Five conventional assessment units (AUs) were defined for the Midway (Paleocene) and Wilcox (Paleocene-Eocene) Groups, and the Carrizo Sand of the Claiborne Group (Eocene) interval including: (1) the Wilcox Stable Shelf Oil and Gas AU; (2) the Wilcox Expanded Fault Zone Gas and Oil AU; (3) the Wilcox-Lobo Slide Block Gas AU; (4) the Wilcox Slope and Basin Floor Gas AU; and (5) the Wilcox Mississippi Embayment AU (not quantitatively assessed).The USGS assessment of undiscovered oil and gas resources for the Midway-Wilcox-Carrizo interval resulted in estimated mean values of 110 million barrels of oil (MMBO), 36.9 trillion cubic feet of gas (TCFG), and 639 million barrels of natural gas liquids (MMBNGL) in the four assessed units. The undiscovered oil resources are almost evenly divided between fluvial-deltaic sandstone reservoirs within the Wilcox Stable Shelf (54 MMBO) AU and deltaic sandstone reservoirs of the Wilcox Expanded Fault Zone (52 MMBO) AU. Greater than 70 percent of the undiscovered gas and 66 percent of the natural gas liquids (NGL) are estimated to be in deep (13,000 to 30,000 feet), untested distal deltaic and slope sandstone reservoirs within the Wilcox Slope and Basin Floor Gas AU.

  19. Geologic assessment of undiscovered oil and gas resources—Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups, United States Gulf of Mexico Coastal Plain and State Waters

    Science.gov (United States)

    Swanson, Sharon M.; Enomoto, Catherine B.; Dennen, Kristin O.; Valentine, Brett J.; Cahan, Steven M.

    2017-02-10

    In 2010, the U.S. Geological Survey (USGS) assessed Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups and their equivalent units for technically recoverable, undiscovered hydrocarbon resources underlying onshore lands and State Waters of the Gulf Coast region of the United States. This assessment was based on a geologic model that incorporates the Upper Jurassic-Cretaceous-Tertiary Composite Total Petroleum System (TPS) of the Gulf of Mexico basin; the TPS was defined previously by the USGS assessment team in the assessment of undiscovered hydrocarbon resources in Tertiary strata of the Gulf Coast region in 2007. One conventional assessment unit (AU), which extends from south Texas to the Florida panhandle, was defined: the Fredericksburg-Buda Carbonate Platform-Reef Gas and Oil AU. The assessed stratigraphic interval includes the Edwards Limestone of the Fredericksburg Group and the Georgetown and Buda Limestones of the Washita Group. The following factors were evaluated to define the AU and estimate oil and gas resources: potential source rocks, hydrocarbon migration, reservoir porosity and permeability, traps and seals, structural features, paleoenvironments (back-reef lagoon, reef, and fore-reef environments), and the potential for water washing of hydrocarbons near outcrop areas.In Texas and Louisiana, the downdip boundary of the AU was defined as a line that extends 10 miles downdip of the Lower Cretaceous shelf margin to include potential reef-talus hydrocarbon reservoirs. In Mississippi, Alabama, and the panhandle area of Florida, where the Lower Cretaceous shelf margin extends offshore, the downdip boundary was defined by the offshore boundary of State Waters. Updip boundaries of the AU were drawn based on the updip extent of carbonate rocks within the assessed interval, the presence of basin-margin fault zones, and the presence of producing wells. Other factors evaluated were the middle

  20. Existence of undiscovered Uranian satellites

    International Nuclear Information System (INIS)

    Boice, D.C.

    1986-04-01

    Structure in the Uranian ring system as observed in recent occultations may contain indirect evidence for the existence of undiscovered satellites. Using the Alfven and Arrhenius (1975, 1976) scenario for the formation of planetary systems, the orbital radii of up to nine hypothetical satellites interior to Miranda are computed. These calculations should provide interesting comparisons when the results from the Voyager 2 encounter with Uranus are made public. 15 refs., 1 fig., 1 tab

  1. Geology and sequence stratigraphy of undiscovered oil and gas resources in conventional and continuous petroleum systems in the Upper Cretaceous Eagle Ford Group and related strata, U.S. Gulf Coast Region

    Science.gov (United States)

    Dubiel, Russell F.; Pearson, Ofori N.; Pitman, Janet K.; Pearson, Krystal M.; Kinney, Scott A.

    2012-01-01

    The U.S. Geological Survey (USGS) recently assessed the technically recoverable undiscovered oil and gas onshore and in State waters of the Gulf Coast region of the United States. The USGS defined three assessment units (AUs) with potential undiscovered conventional and continuous oil and gas resources in Upper Cretaceous (Cenomanian to Turonian) strata of the Eagle Ford Group and correlative rocks. The assessment is based on geologic elements of a total petroleum system, including hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and traps (formation, timing, and seals). Conventional oil and gas undiscovered resources are in updip sandstone reservoirs in the Upper Cretaceous Tuscaloosa and Woodbine Formations (or Groups) in Louisiana and Texas, respectively, whereas continuous oil and continuous gas undiscovered resources reside in the middip and downdip Upper Cretaceous Eagle Ford Shale in Texas and the Tuscaloosa marine shale in Louisiana. Conventional resources in the Tuscaloosa and Woodbine are included in the Eagle Ford Updip Sandstone Oil and Gas AU, in an area where the Eagle Ford Shale and Tuscaloosa marine shale display vitrinite reflectance (Ro) values less than 0.6%. The continuous Eagle Ford Shale Oil AU lies generally south of the conventional AU, is primarily updip of the Lower Cretaceous shelf edge, and is defined by thermal maturity values within shales of the Eagle Ford and Tuscaloosa that range from 0.6 to 1.2% Ro. Similarly, the Eagle Ford Shale Gas AU is defined downdip of the shelf edge where source rocks have Ro values greater than 1.2%. For undiscovered oil and gas resources, the USGS assessed means of: 1) 141 million barrels of oil (MMBO), 502 billion cubic feet of natural gas (BCFG), and 4 million barrels of natural gas liquids (MMBNGL) in the Eagle Ford Updip Sandstone Oil and Gas AU; 2) 853 MMBO, 1707 BCFG, and 34 MMBNGL in the

  2. Fault Recoverability Analysis via Cross-Gramian

    DEFF Research Database (Denmark)

    Shaker, Hamid Reza

    2016-01-01

    Engineering systems are vulnerable to different kinds of faults. Faults may compromise safety, cause sub-optimal operation and decline in performance if not preventing the whole system from functioning. Fault tolerant control (FTC) methods ensure that the system performance maintains within...... with feedback control. Fault recoverability provides important and useful information which could be used in analysis and design. However, computing fault recoverability is numerically expensive. In this paper, a new approach for computation of fault recoverability for bilinear systems is proposed...... approach for computation of fault recoverability is proposed which reduces the computational burden significantly. The proposed results are used for an electro-hydraulic drive to reveal the redundant actuating capabilities in the system....

  3. Geology and undiscovered resource assessment of the potash-bearing Pripyat and Dnieper-Donets Basins, Belarus and Ukraine

    Science.gov (United States)

    Cocker, Mark D.; Orris, Greta J.; Dunlap, Pamela; Lipin, Bruce R.; Ludington, Steve; Ryan, Robert J.; Słowakiewicz, Mirosław; Spanski, Gregory T.; Wynn, Jeff; Yang, Chao

    2017-08-03

    six potash mines in the Starobin area. Published reserves in the Pripyat Basin area are about 7.3 billion metric tons of potash ore (about 1.3 billion metric tons of K2O) mostly from potash-bearing salt horizons in the Starobin and Petrikov mine areas. The 15,160-square-kilometer area of the Pripyat Basin underlain by Famennian potash-bearing salt contains as many as 60 known potash-bearing salt horizons. Rough estimates of the total mineral endowment associated with stratabound Famennian salt horizons in the Pripyat Basin range from 80 to 200 billion metric tons of potash-bearing salt that could contain 15 to 30 billion metric tons of K2O.Parameters (including the number of economic potash horizons, grades, and depths) for these estimates are not published so the estimates are not easily confirmed. Historically, reserves have been estimated above a depth of 1,200 meters (m) (approximately the depths of conventional underground mining). Additional undiscovered K2O resources could be significantly greater in the remainder of the Fammenian salt depending on the extents and grades of the 60 identified potash horizons above the USGS assessment depth of 3,000 m in the remainder of the tract. Increasing ambient temperatures with increasing depths in the eastern parts of the Pripyat Basin may require a solution mining process which is aided by higher temperatures.No resource or reserve data have been published and little is known about stratabound Famennian and Frasnian salt in the Dnieper-Donets Basin. These Upper Devonian salt units dip to the southeast and extend to depths of 15–19 kilometers (km) or greater. The tract of stratabound Famennian salt that lies above a depth of 3 km, the depth above which potash is technically recoverable by solution mining, underlies an area of about 15,600 square kilometers (km2). If Upper Devonian salt units in the Dnieper-Donets Basin contain potash-bearing strata similar to salt of the same age in the Pripyat Basin, then the

  4. Assessment of undiscovered conventional oil and gas resources of Thailand

    Science.gov (United States)

    Schenk, Chris

    2011-01-01

    The U.S. Geological Survey estimated mean volumes of 1.6 billion barrels of undiscovered conventional oil and 17 trillion cubic feet of undiscovered conventional natural gas in three geologic provinces of Thailand using a geology-based methodology. Most of the undiscovered conventional oil and gas resource is estimated to be in the area known as offshore Thai Basin province.

  5. Undiscovered porphyry copper resources in the Urals—A probabilistic mineral resource assessment

    Science.gov (United States)

    Hammarstrom, Jane M.; Mihalasky, Mark J.; Ludington, Stephen; Phillips, Jeffrey; Berger, Byron R.; Denning, Paul; Dicken, Connie; Mars, John; Zientek, Michael L.; Herrington, Richard J.; Seltmann, Reimar

    2017-01-01

    A probabilistic mineral resource assessment of metal resources in undiscovered porphyry copper deposits of the Ural Mountains in Russia and Kazakhstan was done using a quantitative form of mineral resource assessment. Permissive tracts were delineated on the basis of mapped and inferred subsurface distributions of igneous rocks assigned to tectonic zones that include magmatic arcs where the occurrence of porphyry copper deposits within 1 km of the Earth's surface are possible. These permissive tracts outline four north-south trending volcano-plutonic belts in major structural zones of the Urals. From west to east, these include permissive lithologies for porphyry copper deposits associated with Paleozoic subduction-related island-arc complexes preserved in the Tagil and Magnitogorsk arcs, Paleozoic island-arc fragments and associated tonalite-granodiorite intrusions in the East Uralian zone, and Carboniferous continental-margin arcs developed on the Kazakh craton in the Transuralian zone. The tracts range from about 50,000 to 130,000 km2 in area. The Urals host 8 known porphyry copper deposits with total identified resources of about 6.4 million metric tons of copper, at least 20 additional porphyry copper prospect areas, and numerous copper-bearing skarns and copper occurrences.Probabilistic estimates predict a mean of 22 undiscovered porphyry copper deposits within the four permissive tracts delineated in the Urals. Combining estimates with established grade and tonnage models predicts a mean of 82 million metric tons of undiscovered copper. Application of an economic filter suggests that about half of that amount could be economically recoverable based on assumed depth distributions, availability of infrastructure, recovery rates, current metals prices, and investment environment.

  6. An Estimate of Recoverable Heavy Oil Resources of the Orinoco Oil Belt, Venezuela

    Science.gov (United States)

    Schenk, Christopher J.; Cook, Troy A.; Charpentier, Ronald R.; Pollastro, Richard M.; Klett, Timothy R.; Tennyson, Marilyn E.; Kirschbaum, Mark A.; Brownfield, Michael E.; Pitman, Janet K.

    2009-01-01

    The Orinoco Oil Belt Assessment Unit of the La Luna-Quercual Total Petroleum System encompasses approximately 50,000 km2 of the East Venezuela Basin Province that is underlain by more than 1 trillion barrels of heavy oil-in-place. As part of a program directed at estimating the technically recoverable oil and gas resources of priority petroleum basins worldwide, the U.S. Geological Survey estimated the recoverable oil resources of the Orinoco Oil Belt Assessment Unit. This estimate relied mainly on published geologic and engineering data for reservoirs (net oil-saturated sandstone thickness and extent), petrophysical properties (porosity, water saturation, and formation volume factors), recovery factors determined by pilot projects, and estimates of volumes of oil-in-place. The U.S. Geological Survey estimated a mean volume of 513 billion barrels of technically recoverable heavy oil in the Orinoco Oil Belt Assessment Unit of the East Venezuela Basin Province; the range is 380 to 652 billion barrels. The Orinoco Oil Belt Assessment Unit thus contains one of the largest recoverable oil accumulations in the world.

  7. Biodiversity hotspots house most undiscovered plant species.

    Science.gov (United States)

    Joppa, Lucas N; Roberts, David L; Myers, Norman; Pimm, Stuart L

    2011-08-09

    For most organisms, the number of described species considerably underestimates how many exist. This is itself a problem and causes secondary complications given present high rates of species extinction. Known numbers of flowering plants form the basis of biodiversity "hotspots"--places where high levels of endemism and habitat loss coincide to produce high extinction rates. How different would conservation priorities be if the catalog were complete? Approximately 15% more species of flowering plant are likely still undiscovered. They are almost certainly rare, and depending on where they live, suffer high risks of extinction from habitat loss and global climate disruption. By using a model that incorporates taxonomic effort over time, regions predicted to contain large numbers of undiscovered species are already conservation priorities. Our results leave global conservation priorities more or less intact, but suggest considerably higher levels of species imperilment than previously acknowledged.

  8. Chapter 7. The GIS project for the geologic assessment of undiscovered oil and gas in the Cotton Valley group and Travis Peak and Hosston formations, East Texas basin and Louisiana-Mississippi salt basins provinces.

    Science.gov (United States)

    Biewick, Laura

    2006-01-01

    A geographic information system (GIS) focusing on the Upper Jurassic-Lower Cretaceous Cotton Valley Group and the Lower Cretaceous Travis Peak and Hosston Formations in the northern Gulf Coast region was developed as a visual-analysis tool for the U.S. Geological Survey's 2002 assessment of undiscovered, technically recoverable oil and natural gas resources in the East Texas Basin and Louisiana-Mississippi Salt Basins Provinces. The Central Energy Resources Team of the U.S. Geological Survey has also developed an Internet Map Service to deliver the GIS data to the public. This mapping tool utilizes information from a database about the oil and natural gas endowment of the United States-including physical locations of geologic and geographic data-and converts the data into visual layers. Portrayal and analysis of geologic features on an interactive map provide an excellent tool for understanding domestic oil and gas resources for strategic planning, formulating economic and energy policies, evaluating lands under the purview of the Federal Government, and developing sound environmental policies. Assessment results can be viewed and analyzed or downloaded from the internet web site, http://energy.cr.usgs.gov/oilgas/noga/ .

  9. ANCCLI White Paper IV. Cigeo: the challenges of reversibility and recoverability

    International Nuclear Information System (INIS)

    Delalonde, Jean-Claude; Sene, Monique

    2017-01-01

    This white paper aims at providing useful elements for a better understanding, debate and implication of everyone in the preparation of a governance regarding very long life radioactive wastes. The authors first make a set of recommendations for a pluralist governance in decisions, for the creation of permanent pluralist bodies at the local and national levels, for the guarantee of the sustainability of governance structures, for the building up of a citizen vigilance, and for the taking of specific needs of location territories into account. Then, the report describes the different stages of development of a reversible storage, discusses the different definitions of reversibility and the benefits and drawbacks of reversibility and recoverability. It addresses technical and related aspects of parcel recoverability, outlines how to achieve sustainable vigilance and governance. It indicates the role of the different institutional actors (ANDRA, ASN, IRSN) as they themselves define it regarding the issue of reversibility and recoverability. It states the point of view of the ANCCLI's GPMDR (Permanent group for radioactive materials and wastes) about the Cigeo project, about the issue of reversibility, and about the involvement of civil society on the long term. An appendix discusses the issue of waste inventory and classification. Some current research works on these issues are briefly mentioned

  10. The economic impact of proposed regulations on the discharge of drilling muds and cuttings from the offshore facilities on US undiscovered crude oil reserves

    International Nuclear Information System (INIS)

    1989-01-01

    This paper presents the results of an assessment of the potential economic impact of proposed regulations. on the discharge of drilling fluids (muds) and cuttings on US offshore undiscovered crude oil resources. These regulations include proposed Best Available Technology economically achievable (BAT) and New Source Performance Standards (NSPS) effluent limitations under the Clean Water Act governing the discharge of drilling fluids and drill cuttings from offshore oil and gas drilling operations. The impact of the proposed RAT/NSPS regulations for the drilling fluids and drill cuttings disposal on the cost of funding, developing, and producing Lower-48 offshore undiscovered crude oil resources will depend significantly on operators perceptions on the chances of failing toxicity or static sheen tests. If operators, in economically justifying their projects, assume that the fluids fail one of these tests, thereby prohibiting them from being discharged, up to 11% of the economically recoverable offshore resource would be considered uneconomic to produce. This would amount to 845 million barrels of oil at an oil price around $25 per barrel. On the other hand, if operators are willing co take their chances and see if their fluids fail one of these tests, then, based on EPA's assumptions concerning forecast fluid use and static sheen and toxicity test failure rates, up to 4% of the offshore undiscovered resource would be impacted, amounting to lost reserves of up to 270 million barrels

  11. USGS assessment of undiscovered oil and gas resources for the Oligocene Frio and Anahuac formations, U.S. Gulf of Mexico coastal plain and state waters: Review of assessment units

    Science.gov (United States)

    Swanson, Sharon M.; Karlsen, Alexander W.; Warwick, Peter D.; Kennan, Lorcan; Pindell, James; Rosen, Norman C.

    2007-01-01

    The Oligocene Frio and Anahuac formations were examined by the U.S. Geological Survey (USGS) as part of an assessment of technically recoverable undiscovered conventional and unconventional hydrocarbon resources in Paleogene and Neogene strata underlying the U.S. Gulf of Mexico Coastal Plain and state waters. Work included the identification of structural, stratigraphic, and tectonic relations between petroleum source rocks and migration pathways to Frio and Anahuac reservoirs; preliminary evaluation of the potential for shallow (less than 3,000 ft) biogenic gas accumulations; and evaluation of the potential for deep, undiscovered gas and oil accumulations in slope and basin floor areas. All assessments were conducted using USGS methodology (http://energy.cr.usgs.gov/oilgas/noga/methodology.html). Final products from the USGS assessment of the Paleogene and Neogene were reported in USGS fact sheets (Dubiel et al., 2007; Warwick et al., 2007).Five assessment units for the Frio Formation were defined, and three of these were based on the character of the reservoirs in relation to growth faults and other related factors: (1) the Frio stable shelf oil and gas assessment unit, which contains thin (average thickness of 34 ft) and shallow reservoirs (average depth of 4,834 ft); (2) the Frio expanded fault zone oil and gas assessment unit, which contains thick (average thickness of 56 ft) and deep reservoirs (average depth of 9,050 ft) in over-pressured intervals; and (3) the Frio slope and basin floor gas assessment unit, which has potential for deep gas (greater than 15,000 ft) and extends from the downdip boundary of the expanded fault zone to the offshore State/Federal water boundary. The fourth Frio assessment unit is the Hackberry oil and gas assessment unit. The Hackberry embayment of southeast Texas and southwest Louisiana consists of a slope facies in the middle part of the Frio Formation. The fifth unit, the Frio basin margin assessment unit, extends from the

  12. Renewable and recoverable energies. ADEME's views

    International Nuclear Information System (INIS)

    2017-12-01

    This report presents the opinion (December 2017) of ADEME, the French office for energy management and sustainable development, on the future prospects of renewable and recoverable energies in France for 2050. It is assessed that, if associated to a firm energy conservation policy, the renewable and recoverable energies will have the ability to cover more than two thirds of the French energy needs in 2050, while ensuring energy supply security and price stability, a high level of energy independence, the preservation of the environment and a re-localization of the production value and of the employment. The report then presents the various renewable and recoverable energies, the assessment of the potential resources, the applications in the residential (individual and collective), industrial and commercial sectors, the comparison with other European countries, the public financial incentives and support, cost estimations of each energy source, assessments of the markets and of the potential economic impacts, etc. Some recommendations are given, notably concerning the necessary public support for the renewable and recoverable energy sectors, and the synergy between power distribution systems and the energy systems. An annex gives details on the environmental impacts of renewable and recoverable energy sources

  13. Quantifying the undiscovered geothermal resources of the United States

    Science.gov (United States)

    Williams, Colin F.; Reed, Marshall J.; DeAngelo, Jacob; Galanis, S. Peter

    2009-01-01

    In 2008, the U.S. Geological Survey (USGS) released summary results of an assessment of the electric power production potential from the moderate- and high-temperature geothermal resources of the United States (Williams et al., 2008a; USGS Fact Sheet 2008-3082; http://pubs.usgs.gov/fs/2008/3082). In the assessment, the estimated mean power production potential from undiscovered geothermal resources is 30,033 Megawatts-electric (MWe), more than three times the estimated mean potential from identified geothermal systems: 9057 MWe. The presence of significant undiscovered geothermal resources has major implications for future exploration and development activities by both the government and private industry. Previous reports summarize the results of techniques applied by the USGS and others to map the spatial distribution of undiscovered resources. This paper describes the approach applied in developing estimates of the magnitude of the undiscovered geothermal resource, as well as the manner in which that resource is likely to be distributed among geothermal systems of varying volume and temperature. A number of key issues constrain the overall estimate. One is the degree to which characteristics of the undiscovered resources correspond to those observed among identified geothermal systems. Another is the evaluation of exploration history, including both the spatial distribution of geothermal exploration activities relative to the postulated spatial distribution of undiscovered resources and the probability of successful discoveries from the application of standard geothermal exploration techniques. Also significant are the physical, chemical, and geological constraints on the formation and longevity of geothermal systems. Important observations from this study include the following. (1) Some of the largest identified geothermal systems, such as The Geysers vapor-dominated system in northern California and the diverse geothermal manifestations found in Yellowstone

  14. Recoverable and Programmable Collapse from Folding Pressurized Origami Cellular Solids.

    Science.gov (United States)

    Li, S; Fang, H; Wang, K W

    2016-09-09

    We report a unique collapse mechanism by exploiting the negative stiffness observed in the folding of an origami solid, which consists of pressurized cells made by stacking origami sheets. Such a collapse mechanism is recoverable, since it only involves rigid folding of the origami sheets and it is programmable by pressure control and the custom design of the crease pattern. The collapse mechanism features many attractive characteristics for applications such as energy absorption. The reported results also suggest a new branch of origami study focused on its nonlinear mechanics associated with folding.

  15. ROPE: Recoverable Order-Preserving Embedding of Natural Language

    Energy Technology Data Exchange (ETDEWEB)

    Widemann, David P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wang, Eric X. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thiagarajan, Jayaraman J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-02-11

    We present a novel Recoverable Order-Preserving Embedding (ROPE) of natural language. ROPE maps natural language passages from sparse concatenated one-hot representations to distributed vector representations of predetermined fixed length. We use Euclidean distance to return search results that are both grammatically and semantically similar. ROPE is based on a series of random projections of distributed word embeddings. We show that our technique typically forms a dictionary with sufficient incoherence such that sparse recovery of the original text is possible. We then show how our embedding allows for efficient and meaningful natural search and retrieval on Microsoft’s COCO dataset and the IMDB Movie Review dataset.

  16. Caring: An Undiscovered "Super Ility" of Smart Healthcare.

    Science.gov (United States)

    Laplante, Nancy; Laplante, Phil; Voas, Jeff

    2016-01-01

    As new and exciting applications emerge using smart technologies, the Internet of Things, data analytics, and others for healthcare, a critical problem is emerging: the potential loss of caring. While these exciting technologies have improved patient care by allowing for better assessment, surveillance, and treatment, the use of technology can disassociate the caregiver from the patient, essentially removing the "care" from healthcare. Here we introduce the notion of caring as an undiscovered ility that ranks at least as important as other well-known ilities in healthcare systems.

  17. Maximum Recoverable Gas from Hydrate Bearing Sediments by Depressurization

    KAUST Repository

    Terzariol, Marco

    2017-11-13

    The estimation of gas production rates from hydrate bearing sediments requires complex numerical simulations. This manuscript presents a set of simple and robust analytical solutions to estimate the maximum depressurization-driven recoverable gas. These limiting-equilibrium solutions are established when the dissociation front reaches steady state conditions and ceases to expand further. Analytical solutions show the relevance of (1) relative permeabilities between the hydrate free sediment, the hydrate bearing sediment, and the aquitard layers, and (2) the extent of depressurization in terms of the fluid pressures at the well, at the phase boundary, and in the far field. Close form solutions for the size of the produced zone allow for expeditious financial analyses; results highlight the need for innovative production strategies in order to make hydrate accumulations an economically-viable energy resource. Horizontal directional drilling and multi-wellpoint seafloor dewatering installations may lead to advantageous production strategies in shallow seafloor reservoirs.

  18. Heavy oil reservoirs recoverable by thermal technology. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Kujawa, P.

    1981-02-01

    This volume contains reservoir, production, and project data for target reservoirs thermally recoverable by steam drive which are equal to or greater than 2500 feet deep and contain heavy oil in the 8 to 25/sup 0/ API gravity range. Data were collected from three source types: hands-on (A), once-removed (B), and twice-removed (C). In all cases, data were sought depicting and characterizing individual reservoirs as opposed to data covering an entire field with more than one producing interval or reservoir. The data sources are listed at the end of each case. This volume also contains a complete listing of operators and projects, as well as a bibliography of source material.

  19. Assessment of undiscovered oil and gas resources in the Paradox Basin Province, Utah, Colorado, New Mexico, and Arizona, 2011

    Science.gov (United States)

    Whidden, Katherine J.

    2012-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 560 million barrels of undiscovered oil, 12,701 billion cubic feet of undiscovered natural gas, and 490 million barrels of undiscovered natural gas liquids in the Paradox Basin of Utah, Colorado, New Mexico, and Arizona.

  20. Assessment of continuous oil and gas resources in the Perth Basin Province, Australia, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Finn, Thomas M.; Mercier, Tracey J.; Hawkins, Sarah J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Klett, Timothy R.; Le, Phuong A.; Leathers-Miller, Heidi M.; Woodall, Cheryl A.

    2017-07-17

    Using a geology-based assessment methodology, the U.S. Geological Survey assessed undiscovered, technically recoverable mean resources of 223 million barrels of oil and 14.5 trillion cubic feet of gas in the Perth Basin Province, Australia.

  1. Assessment of continuous gas resources in the Khorat Plateau Province, Thailand and Laos, 2016

    Science.gov (United States)

    Schenk, Christopher J.; Klett, Timothy R.; Mercier, Tracey J.; Finn, Thomas M.; Tennyson, Marilyn E.; Gaswirth, Stephanie B.; Marra, Kristen R.; Le, Phuong A.; Drake, Ronald M.

    2017-05-25

    Using a geology-based assessment methodology, the U.S. Geological Survey assessed mean undiscovered, technically recoverable resources of 2.3 trillion cubic feet of continuous gas in the Khorat Plateau Province of Thailand and Laos.

  2. Geometallurgical Study of a Gravity Recoverable Gold Orebody

    Directory of Open Access Journals (Sweden)

    Simon C. Dominy

    2018-04-01

    Full Text Available Sheeted vein gold deposits are often characterised by multiple sub-parallel veins and free-milling coarse gold. Inherent mineralisation heterogeneity results in grade and process parameter variability, which increases project risk if not quantified. Measured grade variability is often exacerbated by poorly designed sampling and testwork protocols. Protocols that are optimised within the framework of the Theory of Sampling (TOS to suit the ore type, together with quality assurance/quality control systems, will reduce variability and provide fit-for-purpose results. Geometallurgy can be broadly split into two key approaches: strategic and tactical (or operational. The strategic approach focuses on the whole orebody and long-term life-of-mine view, whereas tactical geometallurgy relates to a more short- to medium-term view during mining. The geometallurgical approach requires spatially distributed samples within a deposit to support variability modelling. Diverse attributes from core logging, mineralogical/textural determination and small-scale tests are used to measure variability. This contribution presents a case study that emphasises an early-stage strategic geometallurgical programme applied to a gravity recoverable gold (GRG dominated deposit. It exemplifies how data can be acquired from a well-designed and planned programme to support resource estimation, a pre-feasibility study, trial mining and fast-track to production. A tactical geometallurgical programme is embedded into the mine operation.

  3. Radioactive waste and recoverable material in France. Summary of the National Inventory 2006

    International Nuclear Information System (INIS)

    2006-01-01

    Thorough knowledge is needed if the various types of radioactive waste are to be managed openly, consistently and in a safe manner. All French radioactive material users have subscribed to this process for many years. Under the terms of the French Act of Parliament of 30 December 1991, the Government commissioned the French National Agency for Radioactive Waste Management (or ANDRA) to carry out a survey of all the radioactive waste present on French Territory. Through its efforts to collect and confirm information from many sources over the years, that is mainly from statements made by waste producers and handlers, ANDRA has built up a database on existing waste and its geographical location. This constantly updated resource has been regularly circulated. At the beginning of the century the Government decided to extend the areas covered by this database, in response to the recommendations made by the National Review Board (CNE) and the Parliamentary Office for Evaluating Scientific and Technology Options (OPECST). This is how the first edition of the National Inventory, published in 2004, came about. The National Inventory of Radioactive Waste and Recoverable Material, presents a full panorama of radioactive waste that it groups into waste families that present homogenous characteristics. It describes the state of the waste that may be conditioned (that is, in its final form) or may not be conditioned (that is, has not been put through sufficient treatments to arrive at its final form) at the end of 2004. Furthermore it presents not only a statistical and geographical summary, but a predictive summary, as it provides waste quantity forecasts for 2010, 2020 and beyond. The Inventory also includes recoverable materials that contain radioactivity. They are always accounted for separately because of their special nature. The data is presented in a synthesis report. This summary is the general public version of the report. The synthesis report offers more in

  4. Radioactive waste and recoverable material in France. Summary of the National Inventory 2006

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    Thorough knowledge is needed if the various types of radioactive waste are to be managed openly, consistently and in a safe manner. All French radioactive material users have subscribed to this process for many years. Under the terms of the French Act of Parliament of 30 December 1991, the Government commissioned the French National Agency for Radioactive Waste Management (or ANDRA) to carry out a survey of all the radioactive waste present on French Territory. Through its efforts to collect and confirm information from many sources over the years, that is mainly from statements made by waste producers and handlers, ANDRA has built up a database on existing waste and its geographical location. This constantly updated resource has been regularly circulated. At the beginning of the century the Government decided to extend the areas covered by this database, in response to the recommendations made by the National Review Board (CNE) and the Parliamentary Office for Evaluating Scientific and Technology Options (OPECST). This is how the first edition of the National Inventory, published in 2004, came about. The National Inventory of Radioactive Waste and Recoverable Material, presents a full panorama of radioactive waste that it groups into waste families that present homogenous characteristics. It describes the state of the waste that may be conditioned (that is, in its final form) or may not be conditioned (that is, has not been put through sufficient treatments to arrive at its final form) at the end of 2004. Furthermore it presents not only a statistical and geographical summary, but a predictive summary, as it provides waste quantity forecasts for 2010, 2020 and beyond. The Inventory also includes recoverable materials that contain radioactivity. They are always accounted for separately because of their special nature. The data is presented in a synthesis report. This summary is the general public version of the report. The synthesis report offers more in

  5. Assessment of undiscovered, conventional oil and gas resources of Mexico, Guatemala, and Belize, 2012

    Science.gov (United States)

    Schenk, Christopher J.; Brownfield, Michael E.; Charpentier, Ronald R.; Cook, Troy A.; Klett, Timothy R.; Pitman, Janet K.; Pollastro, Richard M.; Weaver, Jean N.

    2012-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 19 billion barrels of oil and 83 trillion cubic feet of undiscovered natural gas resources in 10 geologic provinces of Mexico, Guatemala, and Belize.

  6. Undiscovered resource evaluation: Towards applying a systematic approach to uranium

    International Nuclear Information System (INIS)

    Fairclough, M.; Katona, L.

    2014-01-01

    Evaluations of potential mineral resource supply range from spatial to aspatial, and everything in between across a range of scales. They also range from qualitative to quantitative with similar hybrid examples across the spectrum. These can compromise detailed deposit-specific reserve and resource calculations, target generative processes and estimates of potential endowments in a broad geographic or geological area. All are estimates until the ore has been discovered and extracted. Contemporary national or provincial scale evaluations of mineral potential are relatively advanced and some include uranium, such as those for South Australia undertaken by the State Geological Survey. These play an important role in land-use planning as well as attracting exploration investment and range from datato knowledge-driven approaches. Studies have been undertaken for the Mt Painter region, as well as for adjacent basins. The process of estimating large-scale potential mineral endowments is critical for national and international planning purposes but is a relatively recent and less common undertaking. In many cases, except at a general level, the data and knowledge for a relatively immature terrain is lacking, requiring assessment by analogy with other areas. Commencing in the 1980s, the United States Geological Survey, and subsequently the Geological Survey of Canada evaluated a range of commodities ranging from copper to hydrocarbons with a view to security of supply. They developed innovative approaches to, as far as practical, reduce the uncertainty and maximise the reproducibility of the calculations in information-poor regions. Yet the approach to uranium was relatively ad hoc and incomplete (such as the US Department of Energy NURE project). Other historic attempts, such as the IAEA-NEA International Uranium Resource Evaluation Project (IUREP) in the 1970s, were mainly qualitative. While there is still no systematic global evaluation of undiscovered uranium resources

  7. Attribute Synthetic Evaluation Model for the CBM Recoverability and Its Application

    Directory of Open Access Journals (Sweden)

    Xiao-gang Xia

    2015-01-01

    Full Text Available The coal-bed methane (CBM recoverability is the basic premise of CBM development practice; in order to effectively evaluate the CBM recoverability, the attribute synthetic evaluation model is established based on the theory and method of attribute mathematics. Firstly, five indexes are chosen to evaluate the recoverability through analyzing the influence factors of CBM, including seam thickness, gas saturation, permeability, reservoir pressure gradient, and hydrogeological conditions. Secondly, the attribute measurement functions of each index are constructed based on the attribute mathematics theory, and the calculation methods of the single index attribute measurement and the synthetic attribute measurement also are provided. Meanwhile, the weight of each index is given with the method of similar number and similar weight; the evaluation results also are determined by the confidence criterion reliability code. At last, according to the application results of the model in some coal target area of Fuxin and Hancheng mine, the evaluation results are basically consistent with the actual situation, which proves that the evaluation model can be used in the CBM recoverability prediction, and an effective method of the CBM recoverability evaluation is also provided.

  8. Remaining recoverable petroleum in giant oil fields of the Los Angeles Basin, southern California

    Science.gov (United States)

    Gautier, Donald L.; Tennyson, Marilyn E.; Cook, Troy A.; Charpentier, Ronald R.; Klett, Timothy R.

    2012-01-01

    Using a probabilistic geology-based methodology, a team of U.S. Geological Survey (USGS) scientists recently assessed the remaining recoverable oil in 10 oil fields of the Los Angeles Basin in southern California. The results of the assessment suggest that between 1.4 and 5.6 billion barrels of additional oil could be recovered from those fields with existing technology.

  9. A Facile and General Approach to Recoverable High-Strain Multishape Shape Memory Polymers.

    Science.gov (United States)

    Li, Xingjian; Pan, Yi; Zheng, Zhaohui; Ding, Xiaobin

    2018-03-01

    Fabricating a single polymer network with no need to design complex structures to achieve an ideal combination of tunable high-strain multiple-shape memory effects and highly recoverable shape memory property is a great challenge for the real applications of advanced shape memory devices. Here, a facile and general approach to recoverable high-strain multishape shape memory polymers is presented via a random copolymerization of acrylate monomers and a chain-extended multiblock copolymer crosslinker. As-prepared shape memory networks show a large width at the half-peak height of the glass transition, far wider than current classical multishape shape memory polymers. A combination of tunable high-strain multishape memory effect and as high as 1000% recoverable strain in a single chemical-crosslinking network can be obtained. To the best of our knowledge, this is the first thermosetting material with a combination of highly recoverable strain and tunable high-strain multiple-shape memory effects. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Genome-Wide Association Study for Susceptibility to and Recoverability From Mastitis in Danish Holstein Cows

    Science.gov (United States)

    Welderufael, B. G.; Løvendahl, Peter; de Koning, Dirk-Jan; Janss, Lucas L. G.; Fikse, W. F.

    2018-01-01

    Because mastitis is very frequent and unavoidable, adding recovery information into the analysis for genetic evaluation of mastitis is of great interest from economical and animal welfare point of view. Here we have performed genome-wide association studies (GWAS) to identify associated single nucleotide polymorphisms (SNPs) and investigate the genetic background not only for susceptibility to – but also for recoverability from mastitis. Somatic cell count records from 993 Danish Holstein cows genotyped for a total of 39378 autosomal SNP markers were used for the association analysis. Single SNP regression analysis was performed using the statistical software package DMU. Substitution effect of each SNP was tested with a t-test and a genome-wide significance level of P-value mastitis were located in or very near to genes that have been reported for their role in the immune system. Genes involved in lymphocyte developments (e.g., MAST3 and STAB2) and genes involved in macrophage recruitment and regulation of inflammations (PDGFD and PTX3) were suggested as possible causal genes for susceptibility to – and recoverability from mastitis, respectively. However, this is the first GWAS study for recoverability from mastitis and our results need to be validated. The findings in the current study are, therefore, a starting point for further investigations in identifying causal genetic variants or chromosomal regions for both susceptibility to – and recoverability from mastitis. PMID:29755506

  11. Large recoverable electrostrain in Mn-doped (Ba,Sr) TiO3 ceramics

    International Nuclear Information System (INIS)

    Zhang, L.X.; Chen, W.; Ren, X.

    2004-01-01

    In this letter we demonstrate that with a different principle, BaTiO 3 ceramics, so far considered as inferior piezoelectrics compared with Pb(Zr,Ti)O 3 (PZT), can show a large recoverable electrostrain. This principle utilizes a point-defect-mediated reversible domain switching mechanism, which can in theory generate 0.368% strain for BaTiO 3 ceramics at the best condition. Experimental results showed that, after aging at room temperature, 1.0 mol % Mn-doped (Ba 0.95 Sr 0.05 )TiO 3 ceramics generate a large recoverable nonlinear strain of about 0.12%-0.15% at a field of 3 kV/mm. This value exceeds that of conventional hard PZT piezoelectric ceramics. A microscopic model for the domain-related electrostrain effect in ceramics is proposed. It is also found that the large electrostrain effect is quite stable with respect to both changing frequency and fatigue cycles. Large electrostrain remains recoverable down to 0.05 Hz and after 10 000 cycles. These results demonstrate the potential of our approach in achieving large recoverable electrostrain in environmental-friendly (Pb-free) ceramics

  12. Assessment of undiscovered conventional oil and gas resources of six geologic provinces of China

    Science.gov (United States)

    Charpentier, Ronald R.; Schenk, Christopher J.; Brownfield, Michael E.; Cook, Troy A.; Klett, Timothy R.; Pitman, Janet K.; Pollastro, Richard M.

    2012-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean volumes of undiscovered conventional petroleum resources in six geologic provinces of China at 14.9 billion barrels of oil, 87.6 trillion cubic feet of natural gas, and 1.4 billion barrels of natural-gas liquids.

  13. Genome-Wide Association Study for Susceptibility to and Recoverability From Mastitis in Danish Holstein Cows

    Directory of Open Access Journals (Sweden)

    B. G. Welderufael

    2018-04-01

    Full Text Available Because mastitis is very frequent and unavoidable, adding recovery information into the analysis for genetic evaluation of mastitis is of great interest from economical and animal welfare point of view. Here we have performed genome-wide association studies (GWAS to identify associated single nucleotide polymorphisms (SNPs and investigate the genetic background not only for susceptibility to – but also for recoverability from mastitis. Somatic cell count records from 993 Danish Holstein cows genotyped for a total of 39378 autosomal SNP markers were used for the association analysis. Single SNP regression analysis was performed using the statistical software package DMU. Substitution effect of each SNP was tested with a t-test and a genome-wide significance level of P-value < 10-4 was used to declare significant SNP-trait association. A number of significant SNP variants were identified for both traits. Many of the SNP variants associated either with susceptibility to – or recoverability from mastitis were located in or very near to genes that have been reported for their role in the immune system. Genes involved in lymphocyte developments (e.g., MAST3 and STAB2 and genes involved in macrophage recruitment and regulation of inflammations (PDGFD and PTX3 were suggested as possible causal genes for susceptibility to – and recoverability from mastitis, respectively. However, this is the first GWAS study for recoverability from mastitis and our results need to be validated. The findings in the current study are, therefore, a starting point for further investigations in identifying causal genetic variants or chromosomal regions for both susceptibility to – and recoverability from mastitis.

  14. Assessment of in-place oil shale resources of the Eocene Green River Formation, a foundation for calculating recoverable resources

    Science.gov (United States)

    Johnson, Ronald C.; Mercier, Tracy

    2011-01-01

    The recently completed assessment of in-place resources of the Eocene Green River Formation in the Piceance Basin, Colorado; the Uinta Basin, Utah and Colorado; and the Greater Green River Basin Wyoming, Colorado, and Utah and their accompanying ArcGIS projects will form the foundation for estimating technically-recoverable resources in those areas. Different estimates will be made for each of the various above-ground and in-situ recovery methodologies currently being developed. Information required for these estimates include but are not limited to (1) estimates of the amount of oil shale that exceeds various grades, (2) overburden calculations, (3) a better understanding of oil shale saline facies, and (4) a better understanding of the distribution of various oil shale mineral facies. Estimates for the first two are on-going, and some have been published. The present extent of the saline facies in all three basins is fairly well understood, however, their original extent prior to ground water leaching has not been studied in detail. These leached intervals, which have enhanced porosity and permeability due to vugs and fractures and contain significant ground water resources, are being studied from available core descriptions. A database of all available xray mineralogy data for the oil shale interval is being constructed to better determine the extents of the various mineral facies. Once these studies are finished, the amount of oil shale with various mineralogical and physical properties will be determined.

  15. Fully automated laboratory for the assay of plutonium in wastes and recoverable scraps

    International Nuclear Information System (INIS)

    Guiberteau, P.; Michaut, F.; Bergey, C.; Debruyne, T.

    1990-01-01

    To determine the plutonium content of wastes and recoverable scraps in intermediate size containers (ten liters) an automated laboratory has been carried out. Two passive methods of measurement are used. Gamma ray spectrometry allows plutonium isotopic analysis, americium determination and plutonium assay in wastes and poor scraps. Calorimetry is used for accurate (± 3%) plutonium determination in rich scraps. A full automation was realized with a barcode management and a supply robot to feed the eight assay set-ups. The laboratory works on a 24 hours per day and 365 days per year basis and has a capacity of 8,000 assays per year

  16. The capability and constraint model of recoverability: An integrated theory of continuity planning.

    Science.gov (United States)

    Lindstedt, David

    2017-01-01

    While there are best practices, good practices, regulations and standards for continuity planning, there is no single model to collate and sort their various recommended activities. To address this deficit, this paper presents the capability and constraint model of recoverability - a new model to provide an integrated foundation for business continuity planning. The model is non-linear in both construct and practice, thus allowing practitioners to remain adaptive in its application. The paper presents each facet of the model, outlines the model's use in both theory and practice, suggests a subsequent approach that arises from the model, and discusses some possible ramifications to the industry.

  17. Assessment of undiscovered sandstone copper deposits of the Kodar-Udokan area, Russia: Chapter M in Global mineral resource assessment

    Science.gov (United States)

    Zientek, Michael L.; Chechetkin, Vladimir S.; Parks, Heather L.; Box, Stephen E.; Briggs, Deborah A.; Cossette, Pamela M.; Dolgopolova, Alla; Hayes, Timothy S.; Seltmann, Reimar; Syusyura, Boris; Taylor, Cliff D.; Wintzer, Niki E.

    2014-01-01

    Mineral resource assessments integrate and synthesize available information as a basis for estimating the location, quality, and quantity of undiscovered mineral resources. This probabilistic mineral resource assessment of undiscovered sandstone copper deposits within Paleoproterozoic metasedimentary rocks of the Kodar-Udokan area in Russia is a contribution to a global assessment led by the U.S. Geological Survey (USGS). The purposes of this study are to (1) delineate permissive areas (tracts) to indicate where undiscovered sandstone-hosted copper deposits may occur within 2 km of the surface, (2) provide a database of known sandstone copper deposits and significant prospects, (3) estimate numbers of undiscovered deposits within these permissive tracts at several levels of confidence, and (4) provide probabilistic estimates of amounts of copper (Cu) and mineralized rock that could be contained in undiscovered deposits within each tract. The workshop for the assessment, held in October 2009, used a three-part form of mineral resource assessment as described by Singer (1993) and Singer and Menzie (2010).

  18. Recoverable Wire-Shaped Supercapacitors with Ultrahigh Volumetric Energy Density for Multifunctional Portable and Wearable Electronics.

    Science.gov (United States)

    Shi, Minjie; Yang, Cheng; Song, Xuefeng; Liu, Jing; Zhao, Liping; Zhang, Peng; Gao, Lian

    2017-05-24

    Wire-shaped supercapacitors (SCs) based on shape memory materials are of considerable interest for next-generation portable and wearable electronics. However, the bottleneck in this field is how to develop the devices with excellent electrochemical performance while well-maintaining recoverability and flexibility. Herein, a unique asymmetric electrode concept is put forward to fabricate smart wire-shaped SCs with ultrahigh energy density, which is realized by using porous carbon dodecahedra coated on NiTi alloy wire and flexible graphene fiber as yarn electrodes. Notably, the wire-shaped SCs not only exhibit high flexibility that can be readily woven into real clothing but also represent the available recoverable ability. When irreversible plastic deformations happen, the deformed shape of the devices can automatically resume the initial predesigned shape in a warm environment (about 35 °C). More importantly, the wire-shaped SCs act as efficient energy storage devices, which display high volumetric energy density (8.9 mWh/cm 3 ), volumetric power density (1080 mW/cm 3 ), strong durability in multiple mechanical states, and steady electrochemical behavior after repeated shape recovery processes. Considering their relative facile fabrication technology and excellent electrochemical performance, this asymmetric electrode strategy produced smart wire-shaped supercapacitors desirable for multifunctional portable and wearable electronics.

  19. Assessment of undiscovered conventional oil and gas resources of the Arabian Peninsula and Zagros Fold Belt, 2012

    Science.gov (United States)

    Pitman, Janet K.; Schenk, Christopher J.; Brownfield, Michael E.; Charpentier, Ronald R.; Cook, Troy A.; Klett, Timothy R.; Pollastro, Richard M.

    2012-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 86 billion barrels of oil and 336 trillion cubic feet of undiscovered natural gas resources in the Arabian Peninsula and Zagros Fold Belt. The USGS assessed the potential for undiscovered conventional oil and gas accumulations within the Arabian Peninsula and Zagros Fold Belt as part of the USGS World Petroleum Resources Project. Twenty-three assessment units within seven petroleum systems were quantitatively assessed in this study, which represents a reassessment of this area last published in 2000.

  20. Methodology for assessment of undiscovered oil and gas resources for the 2008 Circum-Arctic Resource Appraisal

    Science.gov (United States)

    Charpentier, Ronald R.; Moore, Thomas E.; Gautier, D.L.

    2017-11-15

    The methodological procedures used in the geologic assessments of the 2008 Circum-Arctic Resource Appraisal (CARA) were based largely on the methodology developed for the 2000 U.S. Geological Survey World Petroleum Assessment. The main variables were probability distributions for numbers and sizes of undiscovered accumulations with an associated risk of occurrence. The CARA methodology expanded on the previous methodology in providing additional tools and procedures more applicable to the many Arctic basins that have little or no exploration history. Most importantly, geologic analogs from a database constructed for this study were used in many of the assessments to constrain numbers and sizes of undiscovered oil and gas accumulations.

  1. U.S. Geological Survey Assessment of Undiscovered Petroleum Resources of the Hamra Basin, Libya, 2006

    Science.gov (United States)

    ,

    2007-01-01

    The Hamra Basin Province encompasses approximately 244,100 square kilometers (94,250 square miles) and is entirely within Libya. One composite total petroleum system (TPS) was defined for this assessment; it extends from Libya westward into adjacent parts of Algeria and southern Tunisia. The Hamra Basin part of the TPS was subdivided into four assessment units for the purpose of resource assessment. The assessment units cover only 172,390 square kilometers of the Hamra Basin Province; the remaining area has little potential for undiscovered petroleum resources because of the absence of petroleum source rocks. Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean volumes of 784 million barrels of crude oil, 4,748 billion cubic feet of natural gas, and 381 million barrels of natural gas liquids in the Hamra Basin of northwestern Libya. Most of the undiscovered crude oil and natural gas are interpreted to be in deeper parts of the Hamra Basin.

  2. Synthesis and characterization of new magnetically recoverable molybdenum nanocatalyst for epoxidation of olefins

    Energy Technology Data Exchange (ETDEWEB)

    Masteri-Farahani, M., E-mail: mfarahany@yahoo.com [Faculty of Chemistry, University of Tarbiat Moallem, Tehran (Iran, Islamic Republic of); Kashef, Z. [Faculty of Chemistry, University of Tarbiat Moallem, Tehran (Iran, Islamic Republic of)

    2012-04-15

    New heterogeneous molybdenum catalyst was prepared through covalent attachment of a Schiff base ligand on the surface of silica coated magnetite nanoparticles via aminopropyl spacer and subsequent complexation with MoO{sub 2}(acac){sub 2}. The prepared nanocatalyst was characterized with Fourier transform infrared spectroscopy, X-ray diffraction, scanning and transmission electron microscopies and vibrating sample magnetometry. Catalytic epoxidation of some olefins and allylic alcohols by prepared nanocatalyst using tert-butyl hydroperoxide and cumene hydroperoxide as oxidants was achieved with good activities and selectivities. - Highlights: Black-Right-Pointing-Pointer Silica coated magnetite nanoparticles were modified with a Schiff base ligand. Black-Right-Pointing-Pointer Next reaction with MoO{sub 2}(acac){sub 2} afforded magnetically recoverable nanocatalyst. Black-Right-Pointing-Pointer The prepared nanocatalyst catalyzed the epoxidation of olefins with TBHP.

  3. A recoverable gas-cell diagnostic for the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Ratkiewicz, A., E-mail: ratkiewicz1@llnl.gov; Berzak Hopkins, L.; Bleuel, D. L.; Cassata, W. S.; Velsko, C. A.; Yeamans, C. B. [Lawrence Livermore National Laboratory, Livermore, California 95440 (United States); Bernstein, L. A.; Bibber, K. van; Goldblum, B. L. [University of California, Berkeley, California 94720 (United States); Siem, S. [University of Oslo, N-0316 Oslo (Norway); Wiedeking, M. [iThemba LABS, Somerset West 7129 (South Africa)

    2016-11-15

    The high-fluence neutron spectrum produced by the National Ignition Facility (NIF) provides an opportunity to measure the activation of materials by fast-spectrum neutrons. A new large-volume gas-cell diagnostic has been designed and qualified to measure the activation of gaseous substances at the NIF. This in-chamber diagnostic is recoverable, reusable and has been successfully fielded. Data from the qualification of the diagnostic have been used to benchmark an Monte Carlo N-Particle Transport Code simulation describing the downscattered neutron spectrum seen by the gas cell. We present early results from the use of this diagnostic to measure the activation of {sup nat}Xe and discuss future work to study the strength of interactions between plasma and nuclei.

  4. Changes of chloroplast pigments of maize leaves after space flight in recoverable satellite

    International Nuclear Information System (INIS)

    Li Sherong; Zhu Baoge; Liu Genqi

    2001-01-01

    Dried seeds of maize inbred lines were carried by recoverable satellite flying at an altitude of 175-253 km from sea level. The changes of absorption spectra of acetone extracts and chloroplast pigment contents of maize leaves were studied. It showed that the light-absorption characteristics of space-flight treatment (SP) were quite similar to those of the corresponding ground controls (CK) at the same time of sampling. However, the absorbance of the SP were less than CK at absorption peaks of chlorophyll a and b, respectively. The contents of chlorophyll a and chlorophyll b of SP were significantly reduced, and the reduction of chlorophyll b far exceeded chlorophyll a. The contents of chlorophyll a + b were reduced so much that the total amount of their chloroplast pigments was lowered, but Ca/Cb ratio tended to be higher in comparison with CK

  5. Monitoring system and methods for a distributed and recoverable digital control system

    Science.gov (United States)

    Stange, Kent (Inventor); Hess, Richard (Inventor); Kelley, Gerald B (Inventor); Rogers, Randy (Inventor)

    2010-01-01

    A monitoring system and methods are provided for a distributed and recoverable digital control system. The monitoring system generally comprises two independent monitoring planes within the control system. The first monitoring plane is internal to the computing units in the control system, and the second monitoring plane is external to the computing units. The internal first monitoring plane includes two in-line monitors. The first internal monitor is a self-checking, lock-step-processing monitor with integrated rapid recovery capability. The second internal monitor includes one or more reasonableness monitors, which compare actual effector position with commanded effector position. The external second monitor plane includes two monitors. The first external monitor includes a pre-recovery computing monitor, and the second external monitor includes a post recovery computing monitor. Various methods for implementing the monitoring functions are also disclosed.

  6. Method and system for redundancy management of distributed and recoverable digital control system

    Science.gov (United States)

    Stange, Kent (Inventor); Hess, Richard (Inventor); Kelley, Gerald B (Inventor); Rogers, Randy (Inventor)

    2012-01-01

    A method and system for redundancy management is provided for a distributed and recoverable digital control system. The method uses unique redundancy management techniques to achieve recovery and restoration of redundant elements to full operation in an asynchronous environment. The system includes a first computing unit comprising a pair of redundant computational lanes for generating redundant control commands. One or more internal monitors detect data errors in the control commands, and provide a recovery trigger to the first computing unit. A second redundant computing unit provides the same features as the first computing unit. A first actuator control unit is configured to provide blending and monitoring of the control commands from the first and second computing units, and to provide a recovery trigger to each of the first and second computing units. A second actuator control unit provides the same features as the first actuator control unit.

  7. A recoverable gas-cell diagnostic for the National Ignition Facility.

    Science.gov (United States)

    Ratkiewicz, A; Berzak Hopkins, L; Bleuel, D L; Bernstein, L A; van Bibber, K; Cassata, W S; Goldblum, B L; Siem, S; Velsko, C A; Wiedeking, M; Yeamans, C B

    2016-11-01

    The high-fluence neutron spectrum produced by the National Ignition Facility (NIF) provides an opportunity to measure the activation of materials by fast-spectrum neutrons. A new large-volume gas-cell diagnostic has been designed and qualified to measure the activation of gaseous substances at the NIF. This in-chamber diagnostic is recoverable, reusable and has been successfully fielded. Data from the qualification of the diagnostic have been used to benchmark an Monte Carlo N-Particle Transport Code simulation describing the downscattered neutron spectrum seen by the gas cell. We present early results from the use of this diagnostic to measure the activation of nat Xe and discuss future work to study the strength of interactions between plasma and nuclei.

  8. Assessment of undiscovered oil and gas resources of Papua-New Guinea, Eastern Indonesia, and East Timor, 2011

    Science.gov (United States)

    Schenk, Christopher J.; Brownfield, Michael E.; Charpentier, Ronald R.; Cook, Troy A.; Klett, Timothy R.; Pitman, Janet K.; Pollastro, Richard M.

    2012-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 5.8 billion barrels of oil and 115 trillion cubic feet of undiscovered natural gas in five geologic provinces in the areas of Papua New Guinea, eastern Indonesia, and East Timor.

  9. Assessment of undiscovered resources in calcrete uranium deposits, Southern High Plains region of Texas, New Mexico, and Oklahoma, 2017

    Science.gov (United States)

    Hall, Susan M.; Mihalasky, Mark J.; Van Gosen, Bradley S.

    2017-11-14

    The U.S. Geological Survey estimates a mean of 40 million pounds of in-place uranium oxide (U3O8) remaining as potential undiscovered resources in the Southern High Plains region of Texas, New Mexico, and Oklahoma. This estimate used a geology-based assessment method specific to calcrete uranium deposits.

  10. Magnetically recoverable magnetite/gold catalyst stabilized by poly(N-vinyl-2-pyrrolidone) for aerobic oxidation of alcohols.

    Science.gov (United States)

    Chen, Hsiao Wei; Murugadoss, Arumugam; Hor, T S Andy; Sakurai, Hidehiro

    2010-12-29

    Fe(3)O(4):PVP/Au nanocomposite synthesized via a two-step procedure was tested as a quasi-homogenous alcohol oxidation catalyst. It was found that the nanocomposite was able to carry out aerobic oxidation of alcohols in water at room temperature. Studies show rapid magnetic recoverability and reusability characteristics.

  11. Comparison of methods used to estimate conventional undiscovered petroleum resources: World examples

    Science.gov (United States)

    Ahlbrandt, T.S.; Klett, T.R.

    2005-01-01

    Various methods for assessing undiscovered oil, natural gas, and natural gas liquid resources were compared in support of the USGS World Petroleum Assessment 2000. Discovery process, linear fractal, parabolic fractal, engineering estimates, PETRIMES, Delphi, and the USGS 2000 methods were compared. Three comparisons of these methods were made in: (1) the Neuquen Basin province, Argentina (different assessors, same input data); (2) provinces in North Africa, Oman, and Yemen (same assessors, different methods); and (3) the Arabian Peninsula, Arabian (Persian) Gulf, and North Sea (different assessors, different methods). A fourth comparison (same assessors, same assessment methods but different geologic models), between results from structural and stratigraphic assessment units in the North Sea used only the USGS 2000 method, and hence compared the type of assessment unit rather than the method. In comparing methods, differences arise from inherent differences in assumptions regarding: (1) the underlying distribution of the parent field population (all fields, discovered and undiscovered), (2) the population of fields being estimated; that is, the entire parent distribution or the undiscovered resource distribution, (3) inclusion or exclusion of large outlier fields; (4) inclusion or exclusion of field (reserve) growth, (5) deterministic or probabilistic models, (6) data requirements, and (7) scale and time frame of the assessment. Discovery process, Delphi subjective consensus, and the USGS 2000 method yield comparable results because similar procedures are employed. In mature areas such as the Neuquen Basin province in Argentina, the linear and parabolic fractal and engineering methods were conservative compared to the other five methods and relative to new reserve additions there since 1995. The PETRIMES method gave the most optimistic estimates in the Neuquen Basin. In less mature areas, the linear fractal method yielded larger estimates relative to other methods

  12. End-of-Life in the railway sector: Analysis of recyclability and recoverability for different vehicle case studies.

    Science.gov (United States)

    Delogu, Massimo; Del Pero, Francesco; Berzi, Lorenzo; Pierini, Marco; Bonaffini, Davide

    2017-02-01

    The railway system represents one of the most resource-efficient answer to our ever-growing demand for transport service and the development trends for the following years forecast a substantial increase in this sector. Considering the European Union, rolling stock realizes a significant share of both goods and passengers carriage while it is responsible for a derisory quota of environmental impact and energy consumption involved by transportation. Contrary to the low environmental impact, the amount of End-of-Life (EoL) waste generated by rolling stocks in relation to the number of vehicles is notable, much greater than in the case of road vehicles. As railway vehicles are constituted by many heterogeneous components, the EoL rolling stock is a precious source of materials, whose recycling brings measurable economic benefits and needs to be appropriately debated. The paper presents calculation of recoverability/recyclability rate for different typologies of vehicles representative of railway transport; calculation is performed on the basis of primary data and according to the recyclability and recoverability calculation method issued by UNIFE in the context of Product Category Rules (PCR). The typologies of railway vehicles taken into account are electric metro, diesel commuter train and high-speed electric train. The analysis envisages also to replicate the calculation in case innovative materials and manufacturing technologies are adopted in the construction of car-body structure. Results show that recyclability/recoverability rates are abundantly over the quota of 90% for each one of the three trains, these latter being made in major part of metals that benefit from very efficient recovery processes. The adoption of innovative materials and manufacturing technologies for car-body structure involves a scarce reduction of recyclability and recoverability rates (about 2% and 0.2% respectively) due to the introduction of components and materials characterized by

  13. Methods for the estimation and economic evaluation of undiscovered uranium endowment and resources

    International Nuclear Information System (INIS)

    1992-01-01

    The present Instruction Manual was prepared as part of a programme of the International Atomic Energy Agency to supply the international uranium community with standard guides for a number of topics related to uranium resource assessment and supply. The quantitative estimation of undiscovered resources and endowments aims at supplying data on potential mineral resources; these data are needed to compare long term projections with one another and to assess the mineral supplies to be obtained from elsewhere. These objectives have relatively recently been supplemented by the concern of land managers and national policy planners to assess the potential of certain lands before the constitution of national parks and other areas reserved from mineral exploration and development. 88 refs, 28 figs, 33 tabs

  14. Research on interactive genetic-geological models to evaluate favourability for undiscovered uranium resources

    International Nuclear Information System (INIS)

    Finch, W.I.; Granger, H.C.; Lupe, R.; McCammon, R.B.

    1980-01-01

    Current methods of evaluating favourability for undiscovered uranium resources are unduly subjective, quite possibly inconsistent and, as a consequence, of questionable reliability. This research is aimed at reducing the subjectivity and increasing the reliability by designing an improved method that depends largely on geological data and their statistical frequency of occurrence. This progress report outlines a genetic approach to modelling the geological factors that controlled uranium mineralization in order to evaluate the favourability for the occurrence of undiscovered uranium deposits of the type modelled. A genetic model is constructed from all the factors that describe the processes, in chronological sequence, that formed uranium deposits thought to have a common origin. The field and laboratory evidence for the processes constitute a geologic-occurrence base that parallels the chronological sequence of events. The genetic model and the geologic-occurrence base are portrayed as two columns of an interactive matrix called the ''genetic-geologic model''. For each column, eight chronological stages are used to describe the overall formation of the uranium deposits. These stages consist of (1) precursor processes; (2) host-rock formation; (3) preparation of host-rock; (4) uranium-source development; (5) transport of uranium; (6) primary uranium deposition; (7) post-deposition modification; and (8) preservation. To apply the genetic-geological model to evaluate favourability, a question is posed that determines the presence or absence of each attribute listed under the geologic-occurrence base. By building a logic circuit of the attributes according to either their essential or non-essential nature, the resultant match between a well-documented control area and the test area may be determined. The degree of match is a measure of favourability for uranium occurrence as hypothesized in the genetic model

  15. Günther Anders’ Undiscovered Critical Theory of Technology in the Age of Big Data Capitalism

    Directory of Open Access Journals (Sweden)

    Christian Fuchs

    2017-06-01

    Full Text Available Günther Anders (1902-1992 was an Austrian philosopher, critical theorist, political activist, and a writer of poems, short stories and novels. His works on the critical theory of technology have remained rather undiscovered. His main work Die Antiquiertheit des Menschen (The Antiquatedness of the Human Being appeared in two volumes and has thus far not been published in English. This essay reviews key aspects of Anders’ works and uses them to critically assess big data capitalism. It first discusses Anders’ concept of the Promethean gap; the gap between what humans can produce with the help of technologies and the capacity of imagining the negative effects these technologies can have. The essay also engages with Anders’ analysis of commercial television and radio. Anders sees capitalism as having catastrophic potentials. He argues that Auschwitz and Hiroshima are two symbols of 20th-century catastrophism. The article discusses Anders’ letter to Klaus Eichmann, the son of Adolf Eichmann, who was in charge of the organisation of the displacement and deportation of Jews in the Third Reich. It furthermore analyses the exchange of letters between Anders and Claude Eatherly, the pilot of an aircraft that supported dropping the nuclear bomb “Little Boy” on Hiroshima. Finally, the paper engages with Anders’ critique of Martin Heidegger’s philosophy. In the age of the Internet and big data capitalism, Anders’ warnings about the potential negative effects of capitalist technologies and capitalism remain of crucial relevance and have taken on new qualities. Anders’ philosophy is an undiscovered critical theory of technology that allows us to critically understand power structures in the age of big data and social media. Günther Anders and Hannah Arendt. Source: posted on Flickr as CC by acido nucleio, https://www.flickr.com/photos/guntheranders/4248063814

  16. Quantitative Mineral Resource Assessment of Copper, Molybdenum, Gold, and Silver in Undiscovered Porphyry Copper Deposits in the Andes Mountains of South America

    Science.gov (United States)

    Cunningham, Charles G.; Zappettini, Eduardo O.; Vivallo S., Waldo; Celada, Carlos Mario; Quispe, Jorge; Singer, Donald A.; Briskey, Joseph A.; Sutphin, David M.; Gajardo M., Mariano; Diaz, Alejandro; Portigliati, Carlos; Berger, Vladimir I.; Carrasco, Rodrigo; Schulz, Klaus J.

    2008-01-01

    Quantitative information on the general locations and amounts of undiscovered porphyry copper resources of the world is important to exploration managers, land-use and environmental planners, economists, and policy makers. This publication contains the results of probabilistic estimates of the amounts of copper (Cu), molybdenum (Mo), gold (Au), and silver (Ag) in undiscovered porphyry copper deposits in the Andes Mountains of South America. The methodology used to make these estimates is called the 'Three-Part Form'. It was developed to explicitly express estimates of undiscovered resources and associated uncertainty in a form that allows economic analysis and is useful to decisionmakers. The three-part form of assessment includes: (1) delineation of tracts of land where the geology is permissive for porphyry copper deposits to form; (2) selection of grade and tonnage models appropriate for estimating grades and tonnages of the undiscovered porphyry copper deposits in each tract; and (3) estimation of the number of undiscovered porphyry copper deposits in each tract consistent with the grade and tonnage model. A Monte Carlo simulation computer program (EMINERS) was used to combine the probability distributions of the estimated number of undiscovered deposits, the grades, and the tonnages of the selected model to obtain the probability distributions for undiscovered metals in each tract. These distributions of grades and tonnages then can be used to conduct economic evaluations of undiscovered resources in a format usable by decisionmakers. Economic evaluations are not part of this report. The results of this assessment are presented in two principal parts. The first part identifies 26 regional tracts of land where the geology is permissive for the occurrence of undiscovered porphyry copper deposits of Phanerozoic age to a depth of 1 km below the Earth's surface. These tracts are believed to contain most of South America's undiscovered resources of copper. The

  17. Overview of a compre­hensive resource database for the assessment of recoverable hydrocarbons produced by carbon dioxide enhanced oil recovery

    Science.gov (United States)

    Carolus, Marshall; Biglarbigi, Khosrow; Warwick, Peter D.; Attanasi, Emil D.; Freeman, Philip A.; Lohr, Celeste D.

    2017-10-24

    A database called the “Comprehensive Resource Database” (CRD) was prepared to support U.S. Geological Survey (USGS) assessments of technically recoverable hydrocarbons that might result from the injection of miscible or immiscible carbon dioxide (CO2) for enhanced oil recovery (EOR). The CRD was designed by INTEK Inc., a consulting company under contract to the USGS. The CRD contains data on the location, key petrophysical properties, production, and well counts (number of wells) for the major oil and gas reservoirs in onshore areas and State waters of the conterminous United States and Alaska. The CRD includes proprietary data on petrophysical properties of fields and reservoirs from the “Significant Oil and Gas Fields of the United States Database,” prepared by Nehring Associates in 2012, and proprietary production and drilling data from the “Petroleum Information Data Model Relational U.S. Well Data,” prepared by IHS Inc. in 2012. This report describes the CRD and the computer algorithms used to (1) estimate missing reservoir property values in the Nehring Associates (2012) database, and to (2) generate values of additional properties used to characterize reservoirs suitable for miscible or immiscible CO2 flooding for EOR. Because of the proprietary nature of the data and contractual obligations, the CRD and actual data from Nehring Associates (2012) and IHS Inc. (2012) cannot be presented in this report.

  18. Evaluation of segmented gamma scanner measurements on cans of recoverable scrap

    International Nuclear Information System (INIS)

    Shull, A.H.; Weber, J.H.; MacMurdo, K.W.; Baker, L.B.

    1991-01-01

    Savannah River Site (SRS) has had a long-standing concern about the inability to measure recoverable scrap. A segmented gamma scanner (SGS) was evaluated for use in measuring cans of scrap materials. Four scrap cans were selected and re-packaged into containers that could be measured using calorimetry and gamma spectrometry. These scrap cans were later used as working standards for the SGS. In addition, replicate measurements were made on all cans of scrap currently stored with estimated values. Before accepting the SGS measurements on the cans, data from the replicate measurements of the standards and a limited number of process cans were analyzed to determine if there was a significant bias between the SGS and the calorimeter-gamma spectrometer measurements, if the random replication error would be acceptable for accountability, to set control limits for the workings standards, and to determine acceptable differences between replicate measurements. After completing the measurement of all process scrap cans in the inventory, the the final data were analyzed and estimates based on the two sets of data compared. The methodology used to determine the appropriate measurement error model, to estimate the measurement errors, to set control limits, and to determine the significance of the bias will be described as well as a comparison of the error estimates based on the preliminary versus final data

  19. Solar-assisted photodegradation of isoproturon over easily recoverable titania catalysts.

    Science.gov (United States)

    Tolosana-Moranchel, A; Carbajo, J; Faraldos, M; Bahamonde, A

    2017-03-01

    An easily recoverable homemade TiO 2 catalyst (GICA-1) has been evaluated during the overall photodegradation process, understood as photocatalytic efficiency and catalyst recovery step, in the solar light-assisted photodegradation of isoproturon and its reuse in two consecutive cycles. The global feasibility has been compared to the commercial TiO 2 P25. The homemade GICA-1 catalyst presented better sedimentation efficiency than TiO 2 P25 at all studied pHs, which could be explained by its higher average hydrodynamic particle size (3 μm) and other physicochemical surface properties. The evaluation of the overall process (isoproturon photo-oxidation + catalyst recovery) revealed GICA-1 homemade titania catalyst strengths: total removal of isoproturon in less than 60 min, easy recovery by sedimentation, and reusability in two consecutive cycles, without any loss of photocatalytic efficiency. Therefore, considering the whole photocatalytic cycle (good performance in photodegradation plus catalyst recovery step), the homemade GICA-1 photocatalyst resulted in more affordability than commercial TiO 2 P25. Graphical abstract.

  20. A comparison of the recoverable proportion of methicillin-resistant Staphylococcus aureus from two different types of papers.

    Science.gov (United States)

    Kacmaz, Birgul; Gul, Serdar

    2016-01-01

    Paper is used for various purposes in hospitals. Generally, there are two different types of paper, which are commonly used in our facility: wood-free paper, and paper containing wood. We compared the recoverable proportion of methicillin-resistant Staphylococcus aureus (MRSA; ATCC 43300) from the surface of such papers. The papers were divided into two groups: Group 1: wood-free paper; Group 2: paper containing wood. The papers were contaminated in a standardized procedure with 0.1 mL of a 5×10(7) CFU MRSA/mL stock solution. The recoverable proportion of MRSA was higher in the wood-containing papers than in the papers without wood (P=0.043). This study indicates that if paper is purchased for healthcare facilities it should not contain wood, but rather wood-free paper types should be considered.

  1. Recent Advances in Recoverable Systems for the Copper-Catalyzed Azide-Alkyne Cycloaddition Reaction (CuAAC

    Directory of Open Access Journals (Sweden)

    Alessandro Mandoli

    2016-09-01

    Full Text Available The explosively-growing applications of the Cu-catalyzed Huisgen 1,3-dipolar cycloaddition reaction between organic azides and alkynes (CuAAC have stimulated an impressive number of reports, in the last years, focusing on recoverable variants of the homogeneous or quasi-homogeneous catalysts. Recent advances in the field are reviewed, with particular emphasis on systems immobilized onto polymeric organic or inorganic supports.

  2. Water-level and recoverable water in storage changes, High Plains aquifer, predevelopment to 2015 and 2013–15

    Science.gov (United States)

    McGuire, Virginia L.

    2017-06-01

    The High Plains aquifer underlies 111.8 million acres (about 175,000 square miles) in parts of eight States—Colorado, Kansas, Nebraska, New Mexico, Oklahoma, South Dakota, Texas, and Wyoming. Water-level declines began in parts of the High Plains aquifer soon after the beginning of substantial irrigation with groundwater in the aquifer area (about 1950). This report presents water-level changes and change in recoverable water in storage in the High Plains aquifer from predevelopment (about 1950) to 2015 and from 2013 to 2015.The methods to calculate area-weighted, average water-level changes; change in recoverable water in storage; and total recoverable water in storage used geospatial data layers organized as rasters with a cell size of 500 meters by 500 meters, which is an area of about 62 acres. Raster datasets of water-level changes are provided for other uses.Water-level changes from predevelopment to 2015, by well, ranged from a rise of 84 feet to a decline of 234 feet. Water-level changes from 2013 to 2015, by well, ranged from a rise of 24 feet to a decline of 33 feet. The area-weighted, average water-level changes in the aquifer were an overall decline of 15.8 feet from predevelopment to 2015 and a decline of 0.6 feet from 2013 to 2015. Total recoverable water in storage in the aquifer in 2015 was about 2.91 billion acre-feet, which was a decline of about 273.2 million acre-feet since predevelopment and a decline of 10.7 million acre-feet from 2013 to 2015.

  3. Geology and assessment of undiscovered oil and gas resources of the Northwest Laptev Sea Shelf Province, 2008

    Science.gov (United States)

    Klett, Timothy; Pitman, Janet K.; Moore, Thomas E.; Gautier, Donald L.

    2017-12-22

    The U.S. Geological Survey (USGS) has recently assessed the potential for undiscovered oil and gas resources in the Northwest Laptev Sea Shelf Province as part of the USGS Circum-Arctic Resource Appraisal. The province is in the Russian Arctic, east of Severnaya Zemlya and the Taimyr fold-and-thrust belt. The province is separated from the rest of the Laptev Sea Shelf by the Severnyi transform fault. One assessment unit (AU) was defined for this study: the Northwest Laptev Sea Shelf AU. The estimated mean volumes of undiscovered petroleum resources in the Northwest Laptev Sea Shelf Province are approximately 172 million barrels of crude oil, 4.5 trillion cubic feet of natural gas, and 119 million barrels of natural-gas liquids, north of the Arctic Circle.

  4. Spontaneous synthesis of gold nanoparticles on gum arabic-modified iron oxide nanoparticles as a magnetically recoverable nanocatalyst

    Science.gov (United States)

    2012-01-01

    A novel magnetically recoverable Au nanocatalyst was fabricated by spontaneous green synthesis of Au nanoparticles on the surface of gum arabic-modified Fe3O4 nanoparticles. A layer of Au nanoparticles with thickness of about 2 nm was deposited on the surface of gum arabic-modified Fe3O4 nanoparticles, because gum arabic acted as a reducing agent and a stabilizing agent simultaneously. The resultant magnetically recoverable Au nanocatalyst exhibited good catalytic activity for the reduction of 4-nitrophenol with sodium borohydride. The rate constants evaluated in terms of pseudo-first-order kinetic model increased with increase in the amount of Au nanocatalyst or decrease in the initial concentration of 4-nitrophenol. The kinetic data suggested that this catalytic reaction was diffusion-controlled, owing to the presence of gum arabic layer. In addition, this nanocatalyst exhibited good stability. Its activity had no significant decrease after five recycles. This work is useful for the development and application of magnetically recoverable Au nanocatalyst on the basis of green chemistry principles. PMID:22713480

  5. Spontaneous synthesis of gold nanoparticles on gum arabic-modified iron oxide nanoparticles as a magnetically recoverable nanocatalyst.

    Science.gov (United States)

    Wu, Chien-Chen; Chen, Dong-Hwang

    2012-06-19

    A novel magnetically recoverable Au nanocatalyst was fabricated by spontaneous green synthesis of Au nanoparticles on the surface of gum arabic-modified Fe3O4 nanoparticles. A layer of Au nanoparticles with thickness of about 2 nm was deposited on the surface of gum arabic-modified Fe3O4 nanoparticles, because gum arabic acted as a reducing agent and a stabilizing agent simultaneously. The resultant magnetically recoverable Au nanocatalyst exhibited good catalytic activity for the reduction of 4-nitrophenol with sodium borohydride. The rate constants evaluated in terms of pseudo-first-order kinetic model increased with increase in the amount of Au nanocatalyst or decrease in the initial concentration of 4-nitrophenol. The kinetic data suggested that this catalytic reaction was diffusion-controlled, owing to the presence of gum arabic layer. In addition, this nanocatalyst exhibited good stability. Its activity had no significant decrease after five recycles. This work is useful for the development and application of magnetically recoverable Au nanocatalyst on the basis of green chemistry principles.

  6. The tracking performance of distributed recoverable flight control systems subject to high intensity radiated fields

    Science.gov (United States)

    Wang, Rui

    It is known that high intensity radiated fields (HIRF) can produce upsets in digital electronics, and thereby degrade the performance of digital flight control systems. Such upsets, either from natural or man-made sources, can change data values on digital buses and memory and affect CPU instruction execution. HIRF environments are also known to trigger common-mode faults, affecting nearly-simultaneously multiple fault containment regions, and hence reducing the benefits of n-modular redundancy and other fault-tolerant computing techniques. Thus, it is important to develop models which describe the integration of the embedded digital system, where the control law is implemented, as well as the dynamics of the closed-loop system. In this dissertation, theoretical tools are presented to analyze the relationship between the design choices for a class of distributed recoverable computing platforms and the tracking performance degradation of a digital flight control system implemented on such a platform while operating in a HIRF environment. Specifically, a tractable hybrid performance model is developed for a digital flight control system implemented on a computing platform inspired largely by the NASA family of fault-tolerant, reconfigurable computer architectures known as SPIDER (scalable processor-independent design for enhanced reliability). The focus will be on the SPIDER implementation, which uses the computer communication system known as ROBUS-2 (reliable optical bus). A physical HIRF experiment was conducted at the NASA Langley Research Center in order to validate the theoretical tracking performance degradation predictions for a distributed Boeing 747 flight control system subject to a HIRF environment. An extrapolation of these results for scenarios that could not be physically tested is also presented.

  7. Continuous reduction of tellurite to recoverable tellurium nanoparticles using an upflow anaerobic sludge bed (UASB) reactor.

    Science.gov (United States)

    Ramos-Ruiz, Adriana; Sesma-Martin, Juan; Sierra-Alvarez, Reyes; Field, Jim A

    2017-01-01

    According to the U.S. Department of Energy and the European Union, tellurium is a critical element needed for energy and defense technology. Thus methods are needed to recover tellurium from waste streams. The objectives of this study was to determine the feasibility of utilizing upflow anaerobic sludge bed (UASB) reactors to convert toxic tellurite (Te IV ) oxyanions to non-toxic insoluble elemental tellurium (Te 0 ) nanoparticles (NP) that are amendable to separation from aqueous effluents. The reactors were supplied with ethanol as the electron donating substrate to promote the biological reduction of Te IV . One reactor was additionally amended with the redox mediating flavonoid compound, riboflavin (RF), with the goal of enhancing the bioreduction of Te IV . Its performance was compared to a control reactor lacking RF. The continuous formation of Te 0 NPs using the UASB reactors was found to be feasible and remarkably improved by the addition of RF. The presence of this flavonoid was previously shown to enhance the conversion rate of Te IV by approximately 11-fold. In this study, we demonstrated that this was associated with the added benefit of reducing the toxic impact of Te IV towards the methanogenic consortium in the UASB and thus enabled a 4.7-fold higher conversion rate of the chemical oxygen demand. Taken as a whole, this work demonstrates the potential of a methanogenic granular sludge to be applied as a bioreactor technology producing recoverable Te 0 NPs in a continuous fashion. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. MKEM: a Multi-level Knowledge Emergence Model for mining undiscovered public knowledge

    Directory of Open Access Journals (Sweden)

    Song Min

    2010-04-01

    Full Text Available Abstract Background Since Swanson proposed the Undiscovered Public Knowledge (UPK model, there have been many approaches to uncover UPK by mining the biomedical literature. These earlier works, however, required substantial manual intervention to reduce the number of possible connections and are mainly applied to disease-effect relation. With the advancement in biomedical science, it has become imperative to extract and combine information from multiple disjoint researches, studies and articles to infer new hypotheses and expand knowledge. Methods We propose MKEM, a Multi-level Knowledge Emergence Model, to discover implicit relationships using Natural Language Processing techniques such as Link Grammar and Ontologies such as Unified Medical Language System (UMLS MetaMap. The contribution of MKEM is as follows: First, we propose a flexible knowledge emergence model to extract implicit relationships across different levels such as molecular level for gene and protein and Phenomic level for disease and treatment. Second, we employ MetaMap for tagging biological concepts. Third, we provide an empirical and systematic approach to discover novel relationships. Results We applied our system on 5000 abstracts downloaded from PubMed database. We performed the performance evaluation as a gold standard is not yet available. Our system performed with a good precision and recall and we generated 24 hypotheses. Conclusions Our experiments show that MKEM is a powerful tool to discover hidden relationships residing in extracted entities that were represented by our Substance-Effect-Process-Disease-Body Part (SEPDB model.

  9. Assessment of continuous oil and gas resources in the Middle and Upper Magdalena Basins, Colombia, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Brownfield, Michael E.; Tennyson, Marilyn E.; Le, Phuong A.; Mercier, Tracey J.; Finn, Thomas M.; Hawkins, Sarah J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Klett, Timothy R.; Leathers-Miller, Heidi M.; Woodall, Cheryl A.

    2017-09-22

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 0.45 billion barrels of oil and 1.0 trillion cubic feet of gas in the Middle and Upper Magdalena Basins, Colombia.

  10. Assessment of continuous oil and gas resources in the San Jorge Basin Province, Argentina, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Mercier, Tracey J.; Hawkins, Sarah J.; Tennyson, Marilyn E.; Marra, Kristen R.; Finn, Thomas M.; Le, Phuong A.; Brownfield, Michael E.; Leathers-Miller, Heidi M.; Woodall, Cheryl A.

    2017-07-18

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable resources of 78 million barrels of oil and 8.9 trillion cubic feet of gas in the San Jorge Basin Province, Argentina.

  11. Protective coating as a factor to ensure the strength and hydraulic performance of recoverable pipelines

    Directory of Open Access Journals (Sweden)

    Orlov Vladimir Aleksandrovich

    2015-01-01

    Full Text Available The authors present an analysis of various types of internal protective pipeline coatings to ensure the strength and hydraulic characteristics of a remodeled pipeline and related coating methods for effective trenchless renovation of engineering systems, water supply systems and sanitation. As protective coating the authors considered a round profile tube of a smaller diameter than of the old pipe, close to the old pipe, sprayed lining on the basis of inorganic and inorganic materials. The article analyzes the methods of trenchless renovation for applying protective coatings: routing in the old pipeline of new pipes made of polymeric materials or polymeric sleeves, centrifugal spraying on the inner surface of pipelines’ inorganic and organic protective coatings. Special attention was paid to bag technology, providing the required strength properties at specific values of the modulus of elasticity and a number of external factors such as the depth of the existing pipe, the existence and magnitude of the horizon groundwater over it. Also attention is paid to the application technology of tape coatings ribbed profile on the inner surface of pipelines. This technology has a unique feature, which is the ability of recoverable pipeline functioning during its renovation by winding an endless belt and the formation of a new pipe. The tape coating winding is carried out by different types of spiral winding machines. The thickness of the protective coating layer forming the tube remains minimal. Inorganic cement-sand and organic coatings were considered as alternative options for repair of pipelines, which allow to localize the defects in the form of a fistula, minor cracks and other damages. However it is noted that a cement-sandy covering is inferior to organic, because it does not provide the strength characteristics of the pipeline system. The main advantage of the organic coating is mudding fistula of a large diameter, making a high wear

  12. Geology and assessment of undiscovered oil and gas resources of the Yukon Flats Basin Province, 2008

    Science.gov (United States)

    Bird, Kenneth J.; Stanley, Richard G.; Moore, Thomas E.; Gautier, Donald L.

    2017-12-22

    The hydrocarbon potential of the Yukon Flats Basin Province in Central Alaska was assessed in 2004 as part of an update to the National Oil and Gas Assessment. Three assessment units (AUs) were identified and assessed using a methodology somewhat different than that of the 2008 Circum-Arctic Resource Appraisal (CARA). An important difference in the methodology of the two assessments is that the 2004 assessment specified a minimum accumulation size of 0.5 million barrels of oil equivalent (MMBOE), whereas the 2008 CARA assessment specified a minimum size of 50 MMBOE. The 2004 assessment concluded that >95 percent of the estimated mean undiscovered oil and gas resources occur in a single AU, the Tertiary Sandstone AU. This is also the only AU of the three that extends north of the Arctic Circle.For the CARA project, the number of oil and gas accumulations in the 2004 assessment of the Tertiary Sandstone AU was re-evaluated in terms of the >50-MMBOE minimum accumulation size. By this analysis, and assuming the resource to be evenly distributed across the AU, 0.23 oil fields and 1.20 gas fields larger than 50 MMBOE are expected in the part of the AU north of the Arctic Circle. The geology suggests, however, that the area north of the Arctic Circle has a lower potential for oil and gas accumulations than the area to the south where the sedimentary section is thicker, larger volumes of hydrocarbons may have been generated, and potential structural traps are probably more abundant. Because of the low potential implied for the area of the AU north of the Arctic Circle, the Yukon Flats Tertiary Sandstone AU was not quantitatively assessed for the 2008 CARA.

  13. Geologic Assessment of Undiscovered Oil and Gas Resources of the North Cuba Basin, Cuba

    Science.gov (United States)

    Schenk, Christopher J.

    2010-01-01

    Petroleum generation in the North Cuba Basin is primarily the result of thrust loading of Jurassic and Cretaceous source rocks during formation of the North Cuba fold and thrust belt in the Late Cretaceous to Paleogene. The fold and thrust belt formed as Cuban arc-forearc rocks along the leading edge of the Caribbean plate translated northward during the opening of the Yucatan Basin and collided with the passive margin of southern North America in the Paleogene. Petroleum fluids generated during thrust loading migrated vertically into complex structures in the fold and thrust belt, into structures in the foreland basin, and possibly into carbonate reservoirs along the margins of the Yucatan and Bahama carbonate platforms. The U.S. Geological Survey (USGS) defined a Jurassic-Cretaceous Composite Total Petroleum System (TPS) and three assessment units (AU)-North Cuba Fold and Thrust Belt AU, North Cuba Foreland Basin AU, and the North Cuba Platform Margin Carbonate AU-within this TPS based mainly on structure and reservoir type (fig. 1). There is considerable geologic uncertainty as to the extent of petroleum migration that might have occurred within this TPS to form potential petroleum accumulations. Taking this geologic uncertainty into account, especially in the offshore area, the mean volumes of undiscovered resources in the composite TPS of the North Cuba Basin are estimated at (1) 4.6 billion barrels of oil (BBO), with means ranging from an F95 probability of 1 BBO to an F5 probability of 9 BBO; and (2) 8.6 trillion cubic feet of of gas (TCFG), of which 8.6 TCFG is associated with oil fields, and about 1.2 TCFG is in nonassociated gas fields in the North Cuba Foreland Basin AU.

  14. Mapping membrane activity in undiscovered peptide sequence space using machine learning.

    Science.gov (United States)

    Lee, Ernest Y; Fulan, Benjamin M; Wong, Gerard C L; Ferguson, Andrew L

    2016-11-29

    There are some ∼1,100 known antimicrobial peptides (AMPs), which permeabilize microbial membranes but have diverse sequences. Here, we develop a support vector machine (SVM)-based classifier to investigate ⍺-helical AMPs and the interrelated nature of their functional commonality and sequence homology. SVM is used to search the undiscovered peptide sequence space and identify Pareto-optimal candidates that simultaneously maximize the distance σ from the SVM hyperplane (thus maximize its "antimicrobialness") and its ⍺-helicity, but minimize mutational distance to known AMPs. By calibrating SVM machine learning results with killing assays and small-angle X-ray scattering (SAXS), we find that the SVM metric σ correlates not with a peptide's minimum inhibitory concentration (MIC), but rather its ability to generate negative Gaussian membrane curvature. This surprising result provides a topological basis for membrane activity common to AMPs. Moreover, we highlight an important distinction between the maximal recognizability of a sequence to a trained AMP classifier (its ability to generate membrane curvature) and its maximal antimicrobial efficacy. As mutational distances are increased from known AMPs, we find AMP-like sequences that are increasingly difficult for nature to discover via simple mutation. Using the sequence map as a discovery tool, we find a unexpectedly diverse taxonomy of sequences that are just as membrane-active as known AMPs, but with a broad range of primary functions distinct from AMP functions, including endogenous neuropeptides, viral fusion proteins, topogenic peptides, and amyloids. The SVM classifier is useful as a general detector of membrane activity in peptide sequences.

  15. Geology and assessment of undiscovered oil and gas resources of the Timan-Pechora Basin Province, Russia, 2008

    Science.gov (United States)

    Schenk, Christopher J.; Moore, Thomas E.; Gautier, D.L.

    2017-11-15

    The Timan-Pechora Basin Province is a triangular area that represents the northeasternmost cratonic block of east European Russia. A 75-year history of petroleum exploration and production in the area there has led to the discovery of more than 16 billion barrels of oil (BBO) and 40 trillion cubic feet of gas (TCFG). Three geologic assessment units (AUs) were defined for assessing the potential for undiscovered oil and gas resources in the province: (1) the Northwest Izhma Depression AU, which includes all potential structures and reservoirs that formed in the northwestern part of the Izhma-Pechora Depression, although this part of the basin contains only sparse source and reservoir rocks and so was not assessed quantitatively; (2) the Main Basin Platform AU, which includes all potential structures and reservoirs that formed in the central part of the basin, where the tectonic and petroleum system evolution was complex; and (3) the Foredeep Basins AU, which includes all potential structures and reservoirs that formed within the thick sedimentary section of the foredeep basins west of the Uralian fold and thrust belt during the Permian and Triassic Uralian orogeny.For the Timan-Pechora Basin Province, the estimated means of undiscovered resources are 3.3 BBO, 17 TCFG, and 0.3 billion barrels of natural-gas liquids (BBNGL). For the AU areas north of the Arctic Circle in the province, the estimated means of undiscovered resources are 1.7 BBO, 9.0 TCFG, and 0.2 BBNGL. These assessment results indicate that exploration in the Timan-Pechora Basin Province is at a mature level.

  16. The effect of COD loading on the granule-based enhanced biological phosphorus removal system and the recoverability.

    Science.gov (United States)

    Yu, Shenjing; Sun, Peide; Zheng, Wei; Chen, Lujun; Zheng, Xiongliu; Han, Jingyi; Yan, Tao

    2014-11-01

    In this study, the effect of varied COD loading (200, 400, 500, 600 and 800 mg L(-1)) on stability and recoverability of granule-based enhanced biological phosphorus removal (EBPR) system was investigated during continuously 53-d operation. Results showed that COD loading higher than 500 mg L(-1) could obviously deteriorate the granular EBPR system and result in sludge bulking with filamentous bacteria. High COD loading also changed the transformation patterns of poly-β-hydroxyalkanoates (PHAs) and glycogen in metabolism process of polyphosphate-accumulating organisms (PAOs) and inhibited the EPS secretion, which completely destroyed the stability and integrality of granules. Results of FISH indicated that glycogen-accumulating organisms (GAOs) and other microorganisms had a competitive advantage over PAOs with higher COD loading. The community composition and EBPR performance were recovered irreversibly in long time operation when COD loading was higher than 500 mg L(-1). Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Energy Efficiency of Technological Equipment at the Economic Agent by Identifying the Points with Recoverable Heat Potential

    Directory of Open Access Journals (Sweden)

    Arina Negoiţescu

    2017-11-01

    Full Text Available For an energy-efficient future, the EU needs to step up its efforts to maximize energy savings. In this context, the paper addresses the steps needed to establish energy efficiency measures and proposes effective measures to reduce consumption by recovering large amounts of energy lost to industrial consumers. The points with the highest recoverable energy potential have been identified and it is proposed to install the heat recovery systems on the flue gas exhaust circuits and polluted air from Industrial Technological Equipment (ITE such as dyeing/drying cabins (DDC. Therefore, whenever possible and as small as energy saving, energy recovery solutions at any level, but especially at local level, need to be applied. In conclusion, by concentrating all the energy-saving efforts that are still being wasted, Europe can contribute, by saving energy, to ensuring a sustainable energy future

  18. Boosting the Recoverable Energy Density of Lead-Free Ferroelectric Ceramic Thick Films through Artificially Induced Quasi-Relaxor Behavior.

    Science.gov (United States)

    Peddigari, Mahesh; Palneedi, Haribabu; Hwang, Geon-Tae; Lim, Kyung Won; Kim, Ga-Yeon; Jeong, Dae-Yong; Ryu, Jungho

    2018-06-08

    Dielectric ceramic film capacitors, which store energy in the form of electric polarization, are promising for miniature pulsed power electronic device applications. For a superior energy storage performance of the capacitors, large recoverable energy density, along with high efficiency, high power density, fast charge/discharge rate, and good thermal/fatigue stability, is desired. Herein, we present highly dense lead-free 0.942[Na 0.535 K 0.480 NbO 3 ]-0.058LiNbO 3 (KNNLN) ferroelectric ceramic thick films (∼5 μm) demonstrating remarkable energy storage performance. The nanocrystalline KNNLN thick film fabricated by aerosol deposition (AD) process and annealed at 600 °C displayed a quasi-relaxor ferroelectric behavior, which is in contrast to the typical ferroelectric nature of the KNNLN ceramic in its bulk form. The AD film exhibited a large recoverable energy density of 23.4 J/cm 3 , with an efficiency of over 70% under the electric field of 1400 kV/cm. Besides, an ultrahigh power density of 38.8 MW/cm 3 together with a fast discharge speed of 0.45 μs, good fatigue endurance (up to 10 6 cycles), and thermal stability in a wide temperature range of 20-160 °C was also observed. Using the AD process, we could make a highly dense microstructure of the film containing nano-sized grains, which gave rise to the quasi-relaxor ferroelectric characteristics and the remarkable energy storage properties.

  19. Urban Mining: Quality and quantity of recyclable and recoverable material mechanically and physically extractable from residual waste

    International Nuclear Information System (INIS)

    Di Maria, Francesco; Micale, Caterina; Sordi, Alessio; Cirulli, Giuseppe; Marionni, Moreno

    2013-01-01

    Highlights: • Material recycling and recovery from residual waste by physical and mechanical process has been investigated. • About 6% of recyclable can be extracted by NIR and 2-3Dimension selector. • Another 2% of construction materials can be extracted by adopting modified soil washing process. • Extracted material quality is quite high even some residual heavy metal have been detected by leaching test. - Abstract: The mechanically sorted dry fraction (MSDF) and Fines (<20 mm) arising from the mechanical biological treatment of residual municipal solid waste (RMSW) contains respectively about 11% w/w each of recyclable and recoverable materials. Processing a large sample of MSDF in an existing full-scale mechanical sorting facility equipped with near infrared and 2-3 dimensional selectors led to the extraction of about 6% w/w of recyclables with respect to the RMSW weight. Maximum selection efficiency was achieved for metals, about 98% w/w, whereas it was lower for Waste Electrical and Electronic Equipment (WEEE), about 2% w/w. After a simulated lab scale soil washing treatment it was possible to extract about 2% w/w of inert exploitable substances recoverable as construction materials, with respect to the amount of RMSW. The passing curve showed that inert materials were mainly sand with a particle size ranging from 0.063 to 2 mm. Leaching tests showed quite low heavy metal concentrations with the exception of the particles retained by the 0.5 mm sieve. A minimum pollutant concentration was in the leachate from the 10 and 20 mm particle size fractions

  20. Assessment of undiscovered oil and gas resources in the Uteland Butte Member of the Eocene Green River Formation, Uinta Basin, Utah

    Science.gov (United States)

    Johnson, Ronald C.; Birdwell, Justin E.; Mercier, Tracey J.; Brownfield, Michael E.; Charpentier, Ronald R.; Klett, Timothy R.; Leathers, Heidi M.; Schenk, Christopher J.; Tennyson, Marilyn E.

    2015-09-03

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered resources of 214 million barrels of oil, 329 billion cubic feet of associated/dissolved natural gas, and 14 million barrels of natural gas liquids in the informal Uteland Butte member of the Green River Formation, Uinta Basin, Utah.

  1. Highly recoverable pyridinium-tagged Hoveyda-Grubbs pre-catalyst for olefin metathesis. Design of the boomerang ligand toward the optimal compromise between activity and reusability.

    Science.gov (United States)

    Rix, Diane; Caïjo, Fréderic; Laurent, Isabelle; Gulajski, Lukasz; Grela, Karol; Mauduit, Marc

    2007-09-28

    Whereas the boomerang ligand of Hoveyda-Grubbs pre-catalysts can be modified by attachment of a pyridinium tag to its benzylidene moiety, a precise adjustment of the length of the spacer allows the optimum balance to be reached between the activity of the catalyst and its recoverability, exceeding 98% after 6 catalytic runs in the best case.

  2. Catalytic asymmetric dihydroxylation of olefins using a recoverable and reusable OsO(4)2- in ionic liquid [bmim][PF6].

    Science.gov (United States)

    Branco, Luís C; Afonso, Carlos A M

    2002-12-21

    The use of the solvent systems water/ionic liquid or water/ionic liquid/tert-butanol provides a recoverable, reusable, robust and simple system for the asymmetric dihydroxylation of olefins, based on the immobilization of the osmium-ligand catalyst in the ionic liquid phase.

  3. Assessment of undiscovered conventional oil and gas resources, onshore Claiborne Group, United Statespart of the northern Gulf of Mexico Basin

    Science.gov (United States)

    Hackley, P.C.; Ewing, T.E.

    2010-01-01

    The middle Eocene Claiborne Group was assessed for undiscovered conventional hydrocarbon resources using established U.S. Geological Survey assessment methodology. This work was conducted as part of a 2007 assessment of Paleogene-Neogene strata of the northern Gulf of Mexico Basin, including the United States onshore and state waters (Dubiel et al., 2007). The assessed area is within the Upper Jurassic-CretaceousTertiary composite total petroleum system, which was defined for the assessment. Source rocks for Claiborne oil accumulations are interpreted to be organic-rich, downdip, shaley facies of the Wilcox Group and the Sparta Sand of the Claiborne Group; gas accumulations may have originated from multiple sources, including the Jurassic Smackover Formation and the Haynesville and Bossier shales, the Cretaceous Eagle Ford and Pearsall (?) formations, and the Paleogene Wilcox Group and Sparta Sand. Hydrocarbon generation in the basin started prior to deposition of Claiborne sediments and is currently ongoing. Primary reservoir sandstones in the Claiborne Group include, from oldest to youngest, the Queen City Sand, Cook Mountain Formation, Sparta Sand, Yegua Formation, and the laterally equivalent Cockfield Formation. A geologic model, supported by spatial analysis of petroleum geology data, including discovered reservoir depths, thicknesses, temperatures, porosities, permeabilities, and pressures, was used to divide the Claiborne Group into seven assessment units (AUs) with three distinctive structural and depositional settings. The three structural and depositional settings are (1) stable shelf, (2) expanded fault zone, and (3) slope and basin floor; the seven AUs are (1) lower Claiborne stable-shelf gas and oil, (2) lower Claiborne expanded fault-zone gas, (3) lower Claiborne slope and basin-floor gas, (4) lower Claiborne Cane River, (5) upper Claiborne stable-shelf gas and oil, (6) upper Claiborne expanded fault-zone gas, and (7) upper Claiborne slope and basin

  4. The Undiscovered Country: How Many Low-Delta-V Near-Earth Objects Remain to be Found?

    Science.gov (United States)

    Elvis, Martin; Ranjan, Sukrit; Galache, Jose Luis

    2014-11-01

    Low delta-v near-Earth objects (NEOs) are of great interest as targets for science and human missions, for possible retrieval to cis-lunar space and as potential resource targets for both exploration and commercial uses. This interest stems from the exponential nature of the rocket equation that imposes a harsh mass penalty on any mission to a higher delta-v. We have compared the known NEO population from the IAU Minor Planet Center (MPC) with the NEOSSat-1 model residence times for the NEO population (Greenstreet & Gladman, 2012) to assess how many undiscovered NEOs there are as a function of H magnitude and delta-v. We find that the median of known NEOs is at lower delta-v (7.3 km/s) than the model population (9.8 km/s), suggesting a bias toward detecting lower delta-v NEOs. To the precision of our data, which is as low as 40% for the 300-500 m diameter (D) objects, the bulk of the larger D>300 m NEOs have been found from delta-v<10.3 km/s. However in the 50 < D < 300 m range there are tens of thousands of delta-v < 10.3 km/s to be found. We examine the total number of undiscovered NEOs as a function of delta-v and find that to find at least 100 now unknown NEOs requires a threshold delta-v of 5.7 km/s, while to find at least 1000 of them requires a threshold delta-v of 6.2 km/s. These numbers can be used to determine mission delta-v requirements for a given number of suitable targets, that will likely be restricted by other criteria (size, composition, spin state) to a few percent of the total population.

  5. Technical writing versus technical writing

    Science.gov (United States)

    Dillingham, J. W.

    1981-01-01

    Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

  6. Graphene Derivative in Magnetically Recoverable Catalyst Determines Catalytic Properties in Transfer Hydrogenation of Nitroarenes to Anilines with 2-Propanol.

    Science.gov (United States)

    Das, Vijay Kumar; Mazhar, Sumaira; Gregor, Lennon; Stein, Barry D; Morgan, David Gene; Maciulis, Nicholas A; Pink, Maren; Losovyj, Yaroslav; Bronstein, Lyudmila M

    2018-06-14

    Here, we report transfer hydrogenation of nitroarenes to aminoarenes using 2-propanol as a hydrogen source and Ag-containing magnetically recoverable catalysts based on partially reduced graphene oxide (pRGO) sheets. X-ray diffraction and X-ray photoelectron spectroscopy data demonstrated that, during the one-pot catalyst synthesis, formation of magnetite nanoparticles (NPs) is accompanied by the reduction of graphene oxide (GO) to pRGO. The formation of Ag 0 NPs on top of magnetite nanoparticles does not change the pRGO structure. At the same time, the catalyst structure is further modified during the transfer hydrogenation, leading to a noticeable increase of sp 2 carbons. These carbons are responsible for the adsorption of substrate and intermediates, facilitating a hydrogen transfer from Ag NPs and creating synergy between the components of the catalyst. The nitroarenes with electron withdrawing and electron donating substituents allow for excellent yields of aniline derivatives with high regio and chemoselectivity, indicating that the reaction is not disfavored by these functionalities. The versatility of the catalyst synthetic protocol was demonstrated by a synthesis of an Ru-containing graphene derivative based catalyst, also allowing for efficient transfer hydrogenation. Easy magnetic separation and stable catalyst performance in the transfer hydrogenation make this catalyst promising for future applications.

  7. Fe_3O_4@B-MCM-41: A new magnetically recoverable nanostructured catalyst for the synthesis of polyhydroquinolines

    International Nuclear Information System (INIS)

    Abdollahi-Alibeik, Mohammad; Rezaeipoor-Anari, Ali

    2016-01-01

    Boron modified MCM-41 with magnetite core (Fe_3O_4@B-MCM-41) as a new magnetically recoverable heterogeneous catalyst was prepared and characterized by SEM, TEM, BET, XRD, VSM and FT-IR techniques. The catalytic activity of Fe_3O_4@B-MCM-41 was investigated in the four-component reaction of aldehyde, dimedone, active methylene compounds and ammonium acetate for the synthesis of polyhydroquinolines. According to optimization and characterization results the catalyst with Si:B:Fe_3O_4 mole composition of 40:4:1 has the best activity. The catalyst could be recovered easily by external magnet and has excellent reusability many times without significant decrease of activity. - Highlights: • Core–shell Fe_3O_4@MCM-41 nanoparticles modified by boron (Fe_3O_4@B-MCM-41). • Fe_3O_4@B-MCM-41 as reusable catalyst for the synthesis of polyhydroquinolines. • Characterization of Fe_3O_4@B-MCM-41 using SEM, TEM, BET, XRD and FT-IR techniques.

  8. Regional Economic Resilience: Resistance and Recoverability of Resource-Based Cities during Economic Crises in Northeast China

    Directory of Open Access Journals (Sweden)

    Juntao Tan

    2017-11-01

    Full Text Available This paper quantitatively analyzes the economic resilience of resource-based cities (RBCs in Northeast China in terms of resistance and recoverability during two economic crises: the Asian financial crisis and the global financial crisis. Moreover, it analyzes the main factors that affected regional resilience. There are three main findings. First, the RBCs in general demonstrated poor resistance during both recessions, but there were variations among the different types of RBCs. Petroleum and metal cities demonstrated the most resistance, whereas coal cities performed the worst. Second, the influential factors affecting economic resilience varied across the two economic cycles, but location advantage, research and development (R and D intensity, foreign trade dependence ratio, and supporting policies had positive effects on resilience during both economic cycles, while the proportion of employed persons in resource industries had a negative effect. Industrial diversity had a weak and ambiguous effect on resilience. Third, the secondary industry was more resilient during the Asian financial crisis, but the tertiary industry was more resilient during the global financial crisis. This shift may be attributed to both the nature of the crises and the strength of the sectors at the time of the crises.

  9. Qualitative assessment of selected areas of the world for undiscovered sediment-hosted stratabound copper deposits: Chapter Y in Global mineral resource assessment

    Science.gov (United States)

    Zientek, Michael L.; Wintzer, Niki E.; Hayes, Timothy S.; Parks, Heather L.; Briggs, Deborah A.; Causey, J. Douglas; Hatch, Shyla A.; Jenkins, M. Christopher; Williams, David J.; Zientek, Michael L.; Hammarstrom, Jane M.; Johnson, Kathleen M.

    2015-12-14

    A qualitative mineral resource assessment of sediment-hosted stratabound copper mineralized areas for undiscovered copper deposits was performed for 10 selected areas of the world. The areas, in alphabetical order, are (1) Belt-Purcell Basin, United States and Canada; (2) Benguela and Cuanza Basins, Angola; (3) Chuxiong Basin, China; (4) Dongchuan Group rocks, China; (5) Egypt–Israel–Jordan Rift, Egypt, Israel, and Jordan; (6) Maritimes Basin, Canada; (7) Neuquén Basin, Argentina; (8) Northwest Botswana Rift, Botswana and Namibia; (9) Redstone Copperbelt, Canada; and (10) Salta Rift System, Argentina. This assessment (1) outlines the main characteristics of the areas, (2) classifies known deposits by deposit model subtypes, and (3) ranks the areas according to their potential to contain undiscovered copper deposits.

  10. Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

    Science.gov (United States)

    ,

    2013-01-01

    In 2002, the U.S. Geological Survey (USGS) estimated undiscovered oil and gas resources that have the potential for additions to reserves in the San Juan Basin Province, New Mexico and Colorado. Paleozoic rocks were not appraised. The last oil and gas assessment for the province was in 1995. There are several important differences between the 1995 and 2002 assessments. The area assessed is smaller than that in the 1995 assessment. This assessment of undiscovered hydrocarbon resources in the San Juan Basin Province also used a slightly different approach in the assessment, and hence a number of the plays defined in the 1995 assessment are addressed differently in this report. After 1995, the USGS has applied a total petroleum system (TPS) concept to oil and gas basin assessments. The TPS approach incorporates knowledge of the source rocks, reservoir rocks, migration pathways, and time of generation and expulsion of hydrocarbons; thus the assessments are geologically based. Each TPS is subdivided into one or more assessment units, usually defined by a unique set of reservoir rocks, but which have in common the same source rock. Four TPSs and 14 assessment units were geologically evaluated, and for 13 units, the undiscovered oil and gas resources were quantitatively assessed.

  11. Petroleum Systems and Assessment of Undiscovered Oil and Gas in the Raton Basin - Sierra Grande Uplift Province, Colorado and New Mexico - USGS Province 41

    Science.gov (United States)

    Higley, Debra K.

    2007-01-01

    Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas resources of the Raton Basin-Sierra Grande Uplift Province of southeastern Colorado and northeastern New Mexico (USGS Province 41). The Cretaceous Vermejo Formation and Cretaceous-Tertiary Raton Formation have production and undiscovered resources of coalbed methane. Other formations in the province exhibit potential for gas resources and limited production. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define two total petroleum systems and five assessment units. All five assessment units were quantitatively assessed for undiscovered gas resources. Oil resources were not assessed because of the limited potential due to levels of thermal maturity of petroleum source rocks.

  12. Geologic models and evaluation of undiscovered conventional and continuous oil and gas resources: Upper Cretaceous Austin Chalk

    Science.gov (United States)

    Pearson, Krystal

    2012-01-01

    The Upper Cretaceous Austin Chalk forms a low-permeability, onshore Gulf of Mexico reservoir that produces oil and gas from major fractures oriented parallel to the underlying Lower Cretaceous shelf edge. Horizontal drilling links these fracture systems to create an interconnected network that drains the reservoir. Field and well locations along the production trend are controlled by fracture networks. Highly fractured chalk is present along both regional and local fault zones. Fractures are also genetically linked to movement of the underlying Jurassic Louann Salt with tensile fractures forming downdip of salt-related structures creating the most effective reservoirs. Undiscovered accumulations should also be associated with structure-controlled fracture systems because much of the Austin that overlies the Lower Cretaceous shelf edge remains unexplored. The Upper Cretaceous Eagle Ford Shale is the primary source rock for Austin Chalk hydrocarbons. This transgressive marine shale varies in thickness and lithology across the study area and contains both oil- and gas-prone kerogen. The Eagle Ford began generating oil and gas in the early Miocene, and vertical migration through fractures was sufficient to charge the Austin reservoirs.

  13. Assessment of water and proppant quantities associated with petroleum production from the Bakken and Three Forks Formations, Williston Basin Province, Montana and North Dakota, 2016

    Science.gov (United States)

    Haines, Seth; Varela, Brian A.; Hawkins, Sarah J.; Gianoutsos, Nicholas J.; Thamke, Joanna N.; Engle, Mark A.; Tennyson, Marilyn E.; Schenk, Christopher J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Kinney, Scott A.; Mercier, Tracey J.; Martinez, Cericia D.

    2017-06-23

    The U.S. Geological Survey (USGS) has completed an assessment of water and proppant requirements and water production associated with the possible future production of undiscovered oil and gas resources in the Three Forks and Bakken Formations (Late Devonian to Early Mississippian) of the Williston Basin Province in Montana and North Dakota. This water and proppant assessment is directly linked to the geology-based assessment of the undiscovered, technically recoverable continuous oil and gas resources that is described in USGS Fact Sheet 2013–3013.

  14. Imagining Technicities

    DEFF Research Database (Denmark)

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

  15. Clinical cues for detection of people with undiscovered depression in primary health care: a case-control study.

    Science.gov (United States)

    Flyckt, Lena; Hassler, Ejda; Lotfi, Louise; Krakau, Ingvar; Nilsson, Gunnar H

    2014-07-01

    To identify clinical cues indicative of depression in medical records of cases in primary care with undetected depression. Depressive disorders are common; the lifetime risk for men and women is 27% and 45%, respectively. Despite effective treatment methods such as antidepressants and cognitive behavioural therapy, depression often remains undiscovered in primary care, with great implications both on the individual and societal level. Clinical cues indicating depression were sought in medical records the year before an opportunistic screening for depression in primary care. In a previous study of 221 patients in the waiting room of a primary care centre during 10 randomly selected days, 45 (20%) showed signs of depression (MADRS-S ⩾ 12) and 60% of these were verified as having depressive disorders (Prime-MD). These 45 patients constitute the cases in the present study. Age- and gender-matched controls were selected among those who scored below the chosen cut-off level. Seventeen (38%) of the 45 cases compared with eight (18%) of the 45 controls had one or more cues [odds ratio (OR) 2.81; 95% confidence interval (CI): 1.06-7.43]. Sleep disturbance showed the greatest difference between cases and controls (OR 4.53; 95% CI: 1.17-17.55). A significant relationship was found between severity of depression, frequency of cues and lower functional level. Cues were twice as common in patients with undetected depression and their functional level was lower. A two-stage procedure, screening and a structured diagnostic interview, is recommended when sleep disturbances and lowered function are present.

  16. Geology and total petroleum systems of the Paradox Basin, Utah, Colorado, New Mexico, and Arizona

    Science.gov (United States)

    Whidden, Katherine J.; Lillis, Paul G.; Anna, Lawrence O.; Pearson, Krystal M.; Dubiel, Russell F.

    2014-01-01

    The geological model for the development of the Total Petroleum Systems (TPSs) within the Paradox Basin formed the foundation of the recent U.S. Geological Survey assessment of undiscovered, technically recoverable resources in the basin. Five TPSs were defined, of which three have known production and two are hypothetical. These TPSs are based on geologic elements of the basin and the potential development of Precambrian, Devonian, Pennsylvanian, Permian-Mississippian, and Cretaceous source rock intervals.

  17. Technical Network

    CERN Multimedia

    2007-01-01

    In order to optimize the management of the Technical Network (TN), to ease the understanding and purpose of devices connected to the TN, and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive email notifications from IT/CS asking them to add the corresponding information in the network database. Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  18. Technical Network

    CERN Multimedia

    2007-01-01

    In order to optimise the management of the Technical Network (TN), to facilitate understanding of the purpose of devices connected to the TN and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive e-mails from IT/CS asking them to add the corresponding information in the network database at "network-cern-ch". Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  19. Preliminary study on peroxidase isoenzyme detection and RAPD molecular verification for sweet pepper 87-2 carried by a recoverable satellite

    International Nuclear Information System (INIS)

    Liu Min; Li Jinguo; Wang Yalin; Zhang Zan; Xue Huai; Zhang Chunhua; Li Sherong

    1999-01-01

    The detection technology of peroxidase isoenzyme pattern and RAPD (Randomly Amplified Polymorphic DNA) analysis were used to space-flown sweet pepper variety of 87-2 carried by a recoverable satellite, and its correspondent ground control Longjiao-2. Determination of peroxidase isoenzyme revealed that the physiological activities of space-flown sweet pepper were significantly higher than those of its ground control. To detect the polymorphism of gene sequence and the difference in molecular level. 42 primers were used, among them, 38 primers amplified polymorphic products, and the amplified products from 5 primers of sweet pepper 87-2 differed from those of ground control

  20. Executive summary--2002 assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado: Chapter 1 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

    Science.gov (United States)

    ,

    2013-01-01

    In 2002, the U.S. Geological Survey (USGS) estimated undiscovered oil and gas resources that have the potential for additions to reserves in the San Juan Basin Province (5022), New Mexico and Colorado (fig. 1). Paleozoic rocks were not appraised. The last oil and gas assessment for the province was in 1995 (Gautier and others, 1996). There are several important differences between the 1995 and 2002 assessments. The area assessed is smaller than that in the 1995 assessment. This assessment of undiscovered hydrocarbon resources in the San Juan Basin Province also used a slightly different approach in the assessment, and hence a number of the plays defined in the 1995 assessment are addressed differently in this report. After 1995, the USGS has applied a total petroleum system (TPS) concept to oil and gas basin assessments. The TPS approach incorporates knowledge of the source rocks, reservoir rocks, migration pathways, and time of generation and expulsion of hydrocarbons; thus the assessments are geologically based. Each TPS is subdivided into one or more assessment units, usually defined by a unique set of reservoir rocks, but which have in common the same source rock. Four TPSs and 14 assessment units were geologically evaluated, and for 13 units, the undiscovered oil and gas resources were quantitatively assessed.

  1. Effects of dissolved organic matter (DOM) sources and nature of solid extraction sorbent on recoverable DOM composition: Implication into potential lability of different compound groups.

    Science.gov (United States)

    Chen, Meilian; Kim, Sunghwan; Park, Jae-Eun; Kim, Hyun Sik; Hur, Jin

    2016-07-01

    Noting the source-dependent properties of dissolved organic matter (DOM), this study explored the recoverable compounds by solid phase extraction (SPE) of two common sorbents (C18 and PPL) eluted with methanol solvent for contrasting DOM sources via fluorescence excitation-emission matrix coupled with parallel factor analysis (EEM-PARAFAC) and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS). Fresh algae and leaf litter extracts DOM, one riverine DOM, and one upstream lacustrine DOM were selected for the comparison. C18 sorbent was generally found to extract more diverse molecular formula, relatively higher molecular weight, and more heteroatomic DOM compounds within the studied mass range than PPL sorbent except for the leaf litter extract. Even with the same sorbent, the main molecular features of the two end member DOM were distributed on different sides of the axes of a multivariate ordination, indicating the source-dependent characteristics of the recoverable compounds by the sorbents. In addition, further examination of the molecular formula uniquely present in the two end members and the upstream lake DOM suggested that proteinaceous, tannin-like, and heteroatomic DOM constituents might be potential compound groups which are labile and easily degraded during their mobilization into downstream watershed. This study provides new insights into the sorbent selectivity of DOM from diverse sources and potential lability of various compound groups.

  2. Technical Note

    African Journals Online (AJOL)

    Administratör

    In this report on four patients, we did not use any of these techniques. The existence and the site of the fistulas was clearly demonstrated using basic but important preoperative detailed assessment and two intraoperative findings. The preoperative referral note that indicated the site of technical difficulty during the previous ...

  3. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    2010-01-01

    Operational Experience At the end of the first full-year running period of LHC, CMS is established as a reliable, robust and mature experiment. In particular common systems and infrastructure faults accounted for <0.6 % CMS downtime during LHC pp physics. Technical operation throughout the entire year was rather smooth, the main faults requiring UXC access being sub-detector power systems and rack-cooling turbines. All such problems were corrected during scheduled technical stops, in the shadow of tunnel access needed by the LHC, or in negotiated accesses or access extensions. Nevertheless, the number of necessary accesses to the UXC averaged more than one per week and the technical stops were inevitably packed with work packages, typically 30 being executed within a few days, placing a high load on the coordination and area management teams. It is an appropriate moment for CMS Technical Coordination to thank all those in many CERN departments and in the Collaboration, who were involved in CMS techni...

  4. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    2010-01-01

    Operational Experience Since the closure of the detector in February, the technical operation of CMS has been quite smooth and reliable. Some minor interventions in UXC were required to cure failures of power supplies, fans, readout boards and rack cooling connections, but all these failures were repaired in scheduled technical stops or parasitically during access dedicated to fixing LHC technical problems. The only occasion when CMS had to request an access between fills was to search for the source of an alarm from the leak-detection cables mounted in the DT racks. After a few minutes of diagnostic search, a leaking air-purge was found. Replacement was complete within 2 hours. This incident demonstrated once more the value of these leak detection cables; the system will be further extended (during the end of year technical stop) to cover more racks in UXC and the floor beneath the detector. The magnet has also been operating reliably and reacted correctly to the 14s power cut on 29 May (see below). In or...

  5. Technical endoscopy

    International Nuclear Information System (INIS)

    Cavalar, K.O.

    1988-01-01

    A survey is provided on different versions of endoscopes, taking into account the new developments of video endoscopy. With a variety of practical examples it is shown that technical tests using endoscopy are a demanding task for nondestructive testing, whose requirements can only be met on a customized basis. (orig./HP) [de

  6. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Monday 9 February 2004 From 10:00 to 12:00 - IT Auditorium - bldg. 31, 3rd floor ANSOFT High-Frequency Seminar David Prestaux, Application Engineer, ANSOFT F-78535 BUC, France This Technical Training seminar will present two Ansoft application products: Ansoft HFSS and Ansoft Designer. Ansoft HFSS makes use of the Finite Element Method (FEM) to calculate field solutions from first principles. It can accurately predict all high-frequency behaviours such as dispersion, mode conversion, and losses due to materials and radiation. Ansoft Designer is a suite of design tools to fully integrate high-frequency, physics-based electromagnetic simulations into a seamless system-level simulation environment. Ansoft Designer uses a simple interface to give complete control over every design task, by a method allowing multiple solvers, Solver on Demand. • Introduction • Overview of the Ansoft Total solution • Ansoft HFSS 9...

  7. Geologic assessment of undiscovered conventional oil and gas resources--Middle Eocene Claiborne Group, United States part of the Gulf of Mexico Basin

    Science.gov (United States)

    Hackley, Paul C.

    2012-01-01

    The Middle Eocene Claiborne Group was assessed using established U.S. Geological Survey (USGS) assessment methodology for undiscovered conventional hydrocarbon resources as part of the 2007 USGS assessment of Paleogene-Neogene strata of the United States part of the Gulf of Mexico Basin including onshore and State waters. The assessed area is within the Upper Jurassic-Cretaceous-Tertiary Composite total petroleum system, which was defined as part of the assessment. Source rocks for Claiborne oil accumulations are interpreted to be organic-rich downdip shaley facies of the Wilcox Group and the Sparta Sand of the Claiborne Group; gas accumulations may have originated from multiple sources including the Jurassic Smackover and Haynesville Formations and Bossier Shale, the Cretaceous Eagle Ford and Pearsall(?) Formations, and the Paleogene Wilcox Group and Sparta Sand. Hydrocarbon generation in the basin started prior to deposition of Claiborne sediments and is ongoing at present. Emplacement of hydrocarbons into Claiborne reservoirs has occurred primarily via vertical migration along fault systems; long-range lateral migration also may have occurred in some locations. Primary reservoir sands in the Claiborne Group include, from oldest to youngest, the Queen City Sand, Cook Mountain Formation, Sparta Sand, Yegua Formation, and the laterally equivalent Cockfield Formation. Hydrocarbon traps dominantly are rollover anticlines associated with growth faults; salt structures and stratigraphic traps also are important. Sealing lithologies probably are shaley facies within the Claiborne and in the overlying Jackson Group. A geologic model, supported by spatial analysis of petroleum geology data including discovered reservoir depths, thicknesses, temperatures, porosities, permeabilities, and pressures, was used to divide the Claiborne Group into seven assessment units (AU) with distinctive structural and depositional settings. The AUs include (1) Lower Claiborne Stable Shelf

  8. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    Overview From a technical perspective, CMS has been in “beam operation” state since 6th November. The detector is fully closed with all components operational and the magnetic field is normally at the nominal 3.8T. The UXC cavern is normally closed with the radiation veto set. Access to UXC is now only possible during downtimes of LHC. Such accesses must be carefully planned, documented and carried out in agreement with CMS Technical Coordination, Experimental Area Management, LHC programme coordination and the CCC. Material flow in and out of UXC is now strictly controlled. Access to USC remains possible at any time, although, for safety reasons, it is necessary to register with the shift crew in the control room before going down.It is obligatory for all material leaving UXC to pass through the underground buffer zone for RP scanning, database entry and appropriate labeling for traceability. Technical coordination (notably Stephane Bally and Christoph Schaefer), the shift crew and run ...

  9. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2011-01-01

    In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

  10. A facile one-pot solvothermal method for synthesis of magnetically recoverable Pd-Fe3O4 hybrid nanocatalysts for the Mizoroki-Heck reaction

    Science.gov (United States)

    Zhen, Fangchen; Ran, Maofei; Chu, Wei; Jiang, Chengfa; Sun, Wenjing

    2018-03-01

    Pd-Fe3O4 hybrid nanostructures were prepared using a simple one-pot hydrothermal method. The prepared materials were characterized by Fourier transform-infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, inductively coupled plasma, N2 adsorption-desorption, and vibrating sample magnetometry. This self-assembled nanosystem acted as an efficient magnetically recyclable noble metal-based multi-functional nanocatalyst. It showed excellent catalytic activity and stability for the Heck reaction of iodobenzene and styrene under mild conditions. The methods used to prepare the Pd-Fe3O4 catalysts were simple and low-cost, which will be useful for the large-scale development and application of a magnetically recoverable Pd catalyst.

  11. Immobilized Palladium Nanoparticles on Zirconium Carboxy-Aminophosphonates Nanosheets as an Efficient Recoverable Heterogeneous Catalyst for Suzuki–Miyaura and Heck Coupling

    Directory of Open Access Journals (Sweden)

    Vadym Kozell

    2017-06-01

    Full Text Available Zirconium phosphate glycine diphosphonate nanosheets (ZPGly have been used as support for the preparation of solid palladium nanoparticles, namely Pd@ZPGly. Thanks to the presence of carboxy-aminophosponate groups on the layer surface, ZPGly-based materials were able to stabilize a high amount of palladium (up to 22 wt % also minimizing the amount of metal leached in the final products of representative important cross-coupling processes selected for proving the catalysts’ efficiency. The catalytic systems have been fully characterized and used in low amounts (0.1 mol % in the Suzuki–Miyaura and Heck cross-couplings. Moreover, the protocols were optimized for the use of recoverable azeotropic mixtures (aq. EtOH 96% or aq. CH3CN 84%, respectively and in the flow procedure allowing one to isolate the final pure products, without any purification step, with very low residual palladium content and with a very low waste production.

  12. Geology and undiscovered resource assessment of the potash-bearing Central Asia Salt Basin, Turkmenistan, Uzbekistan, Tajikistan, and Afghanistan: Chapter AA in Global mineral resource assessment

    Science.gov (United States)

    Wynn, Jeff; Orris, Greta J.; Dunlap, Pamela; Cocker, Mark D.; Bliss, James D.

    2016-03-23

    Undiscovered potash resources in the Central Asia Salt Basin (CASB) of Turkmenistan, Uzbekistan, Tajikistan, and Afghanistan were assessed as part of a global mineral resource assessment led by the U.S. Geological Survey. The term “potash” refers to potassium-bearing, water-soluble salts derived from evaporite basins, where seawater dried up and precipitated various salt compounds; the word for the element “potassium” is derived from potash. Potash is produced worldwide at amounts exceeding 30 million metric tons per year, mostly for use in fertilizers. The term “potash” is used by industry to refer to potassium chloride, as well as potassium in sulfate, nitrate, and oxide forms. For the purposes of this assessment, the term “potash” refers to potassium ores and minerals and potash ore grades. Resource and production values are usually expressed by industry in terms of K2O (potassium oxide) or muriate of potash (KCl, potassium chloride).

  13. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    Tuesday 30 March TECHNICAL TRAINING SEMINAR From 9:00 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Technical conferences: 09:00 - 12:00 Data acquisition systems on PCs. Industrial measurement and control techniques. 13:00 - 16:00 Advanced LabVIEW software and PXI instrumentation. Measuring instruments and system components for teststand automation. Introductory courses: 09:00 - 12:00 DIAdem: Data analysis and presentation 13:00 - 16:00 Data acquisition with LabVIEW Language: English and French Free special seminar. Registration is recommended with National Instruments Switzerland (please sp...

  14. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    Tuesday 30 March TECHNICAL TRAINING SEMINAR From 9:00 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Technical conferences: 09:00 - 12:00 Data acquisition systems on PCs. Industrial measurement and control techniques. 13:00 - 16:00 Advanced LabVIEW software and PXI instrumentation. Measuring instruments and system components for teststand automation. Introductory courses: 09:00 - 12:00 DIAdem: Data analysis and presentation 13:00 - 16:00 Data acquisition with LabVIEW Language: English and French Free special seminar. Registration is recommended with National Instruments Swi...

  15. USGS assessment of undiscovered oil and gas resources in Paleogene strata of the U.S. Gulf of Mexico coastal plain and state waters

    Science.gov (United States)

    Warwick, Peter D.; Coleman, James; Hackley, Paul C.; Hayba, Daniel O.; Karlsen, Alexander W.; Rowan, Elisabeth L.; Swanson, Sharon M.; Kennan, Lorcan; Pindell, James; Rosen, Norman C.

    2007-01-01

    This report presents a review of the U.S. Geological Survey (USGS) 2007 assessment of the undiscovered oil and gas resources in Paleogene strata underlying the U.S. Gulf of Mexico Coastal Plain and state waters. Geochemical, geologic, geophysical, thermal maturation, burial history, and paleontologic studies have been combined with regional cross sections and data from previous USGS petroleum assessments have helped to define the major petroleum systems and assessment units. Accumulations of both conventional oil and gas and continuous coal-bed gas within these petroleum systems have been digitally mapped and evaluated, and undiscovered resources have been assessed following USGS methodology.The primary source intervals for oil and gas in Paleogene (and Cenozoic) reservoirs are coal and shale rich in organic matter within the Wilcox Group (Paleocene-Eocene) and Sparta Formation of the Claiborne Group (Eocene); in addition, Cretaceous and Jurassic source rocks probably have contributed substantial petroleum to Paleogene (and Cenozoic) reservoirs.For the purposes of the assessment, Paleogene strata have divided into the following four stratigraphic study intervals: (1) Wilcox Group (including the Midway Group and the basal Carrizo Sand of the Claiborne Group; Paleocene-Eocene); (2) Claiborne Group (Eocene); (3) Jackson and Vicksburg Groups (Eocene-Oligocene); and (4) the Frio-Anahuac Formations (Oligocene). Recent discoveries of coal-bed gas in Paleocene strata confirm a new petroleum system that was not recognized in previous USGS assessments. In total, 26 conventional Paleogene assessment units are defined. In addition, four Cretaceous-Paleogene continuous (coal-bed gas) assessment units are included in this report. Initial results of the assessment will be released as USGS Fact Sheets (not available at the time of this writing).Comprehensive reports for each assessment unit are planned to be released via the internet and distributed on CD-ROMs within the next year.

  16. INDOT Technical Training Plan : [Technical Summary

    Science.gov (United States)

    2012-01-01

    A wide range of job classifications, increasing technical : performance expectations, licensing and certification requirements, : budget restrictions and frequent department : reorganization has made technical training of employees : more difficult, ...

  17. TECHNICAL COORDINATION

    CERN Document Server

    A. Ball and W. Zeuner

    2013-01-01

    For the reporting period, the CMS common systems and infrastructure worked well, without failures that caused significant data losses. One more disconnection of the magnet cold box occurred in the shadow of interruptions in data taking, caused by a series of technical faults. The recognition during 2012 that re-connection can only safely be done at around 2 T implies a minimum magnet recovery time of 12 hours and raises serious concerns about the number of ramping cycles of the magnet these incidents cause. This has triggered studies of how to make the cryo-system of the magnet more robust against failures. The proton-proton run ended just before the end-of-year CERN closure, during which CASTOR was installed on the negative end of CMS and both ZDC calorimeters were installed in TAN absorbers the LHC tunnel, in preparation for the heavy-ion run. The installation of CASTOR was an excellent “engineering test” of procedures for working in an activated environment. Despite some technical pr...

  18. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    Summary of progress since last CMS week. Ten years of construction work have been completed. CMS is closed, in very close to the ideal low luminosity configuration, and performed well in the first tests with LHC beam. Behind this encouraging news is the story of a summer of intense commitment by many teams (from the collaboration and 3 CERN departments) working together, against the clock and despite many minor setbacks, to ensure that the experiment was ready to play a leading role in the excitement of September 10. Following beampipe bakeout and refill with pure neon, a magnificent effort by the ECAL group and the pt 5 technical crew made it possible to install and commission all 4 ECAL endcap Dees before the end of August. In the shadow of this activity, the barrel and forward pixel trackers and part of the beam monitoring were installed within the vac tank. The pt 5 technical teams then succeeded in safely removing the 20t installation tables and their support blocks from beneath the already installed ...

  19. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2011-01-01

      Operational experience 2011 CMS is approaching the end of a very successful year of operation. Proton- proton running ended in the late afternoon of 30th October with a stunning 5.73 fb–1 delivered by LHC, of which CMS recorded 5.22 fb–1. During heavy-ion operation, which continues until 7th December, both the accelerator and the CMS detector have also performed very well. Despite the encouraging overall reliability of technical operation, several infrastructure failures which occurred since the last Bulletin are worthy of mention, with one leading for the first time to significant data-loss. On 10th July, a CERN-wide power failure brought down essentially all services including the magnet, due to an MCS setting being left in “manual” after the recent technical stop, but there was no significant damage and the detector was operational before the LHC, despite a slow and tortuous recovery (one of several indications this year that there is room for improve...

  20. Technical presentation

    CERN Multimedia

    GS Department

    2010-01-01

    10 March 2010 DYNEOS 10:00 – 12:00 - Main Building, Room B, 61-1-009 Dyneos AG is active in the fields of photonics, laser and high-precision positioning. Our highly qualified engineer team has more than 30 years of experience in electro-optical solutions sales. The engineers are supported by a technical and administrative team. We are focused on the Swiss market and represent six suppliers (Coherent, PI Physik Instrumente, SIOS, Nanonics Imaging, APE, Ekspla) in order to give a qualified sales and service support to our customers. Our products are dedicated to the research field as well as to industry. In addition to standard catalog products, we offer custom designs to fulfill the specific needs of OEM customers or specific applications.

  1. Technical presentation

    CERN Document Server

    FP Department

    2009-01-01

    07 April 2009 Technical presentation by Leuze Electronics: 14.00 – 15.00, Main Building, Room 61-1-017 (Room A) Photoelectric sensors, data identification and transmission systems, image processing systems. We at Leuze Electronics are "the sensor people": we have been specialising in optoelectronic sensors and safety technology for accident prevention for over 40 years. Our dedicated staff are all highly customer oriented. Customers of Leuze Electronics can always rely on one thing – on us! •\tFounded in 1963 •\t740 employees •\t115 MEUR turnover •\t20 subsidiaries •\t3 production facilities in southern Germany Product groups: •\tPhotoelectric sensors •\tIdentification and measurements •\tSafety devices

  2. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2010-01-01

    Overview Once again, the bulk of this article reviews the intense activity of a recently completed shutdown, which, although quite unforeseeable until a few weeks before it started, proved by its success that our often advertised capability to conduct major maintenance within a two month period is real. Although safely completed, on-time to remarkable precision, the activity was not without incident, and highlighted our dependence on many experienced, specialist teams and their precise choreography. Even after the yoke was safely closed, magnet re-commissioning and beampipe pumpdown showed new and thought-provoking behaviour. The struggle to maintain adequate technical resources will be a pre-occupation over the coming months, in parallel with the start of truly sustained operation, for which various procedures are still being put in place. Planning for future shutdowns must now become a high priority, with many working groups and task forces already in existence to prepare infrastructure improvements and to...

  3. Technical presentation

    CERN Document Server

    FI Department

    2008-01-01

    RADIOSPARES, the leading catalogue distributor of components (electronic, electrical, automation, etc.) and industrial supplies will be at CERN on Friday 3 October 2008 (Main Building, Room B, from 9.00 a.m. to 3.00 p.m.) to introduce its new 2008/2009 catalogue. This will be the opportunity for us to present our complete range of products in more detail: 400 000 part numbers available on our web site (Radiospares France, RS International, extended range of components from other manufacturers); our new services: quotations, search for products not included in the catalogue, SBP products (Small Batch Production: packaging in quantities adapted to customers’ requirements); partnership with our focus manufacturers; demonstration of the on-line purchasing tool implemented on our web site in conjunction with CERN. RADIOSPARES will be accompanied by representatives of FLUKE and TYCO ELECTRONICS, who will make presentations, demonstrate materials and answer any technical questio...

  4. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Tuesday 3 February 2004 From 09:00 to 13:30 - Training Centre Auditorium - bldg. 593, room 11 USB (Universal Serial Bus) CYPRESS Seminar Claudia Colombini, Field Application Engineer CYPRESS ActiveComp Electronic GmbH D-85077 MANCHING, Germany As a pioneer in USB, CYPRESS sets the standard for cost-effective solutions without sacrificing functionality, performance or reliability. Having shipped over 200 million USB devices, Cypress is the undisputed market leader and demonstrates unmatched USB expertise. With the industry's broadest selection of USB solutions, Cypress has the right silicon, software and support for every USB application, from Low-speed to High-Speed and USB On-The-Go (OTG). 9:00 - 10:30 Overview of USB systems. USB CYPRESS product overview. Peripherals: Low Speed, Full Speed, High Speed (1.1 and 2.0). Hub Solutions, Embedded Host Solutions, On-The-Go (OTG) and wireless USB. USB Development Tools (first part) 10:30 -...

  5. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    2013-01-01

      Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

  6. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2012-01-01

      UXC + detectors As explained in detail in the November 2011 bulletin, the bellows unit at −18.5 m from the CMS interaction point was identified as a prime candidate for the regularly occurring pressure spikes which occasionally led to sustained severe background conditions in 2011, affecting dead time and data quality. Similar regions in LHC with vacuum instabilities were observed to be close to bellows, which radiography showed to have distorted RF-fingers — on removal, they proved to have been severely overheated. The plans for the Year-End Technical Stop were adapted to prioritise radiography of the bellows at 16 m to 18 m either end of CMS. Excellent work by the beam pipe, survey and heavy mechanical teams allowed the X-rays to be taken as planned on 20th December, showing that the bellow at −18.5m had an obvious non-conformity. The RF-fingers were found inside the end of the opposing flared pipe instead of outside. In addition, the overlap between fingers and...

  7. SiO2@FeSO4 nano composite: A recoverable nano-catalyst for eco-friendly synthesis oximes of carbonyl compounds

    Directory of Open Access Journals (Sweden)

    Mostafa Karimkoshteh

    2016-01-01

    Full Text Available Various aldoximes and ketoximes synthesis of corresponding aldehydes and ketones in the presence of SiO2@FeSO4 nano composite as recoverable nano catalyst and NH2OH·HCl. The SiO2@FeSO4 nano composite system was carried out between 10 to 15 min in oil bath (70-80 °C under solvent-free condition in excellent yields in addition this protocol can be used for industrial scales. This method offers some advantages in term of clean reaction conditions, easy work-up procedure, short reaction time, applied to convert α-diketones to α-diketoximes (as longer than other carbonyl compounds, α,β-unsaturated aldehydes and ketones to corresponding oximes and suppression of any side product. So we think that NH2OH•HCl/SiO2@FeSO4 nano composite system could be considered a new and useful addition to the present methodologies in this area. Structure of products and nano composite elucidation was carried out by 1H NMR, 13C NMR, FT-IR, scanning electron microscopy (SEM.

  8. Upper and lower bounds on the set of recoverable strains and on effective energies in cubic-to-monoclinic martensitic phase transformations

    Directory of Open Access Journals (Sweden)

    Schlömerkemper Anja

    2015-01-01

    Full Text Available A major open problem in the mathematical analysis of martensitic phase transformations is the derivation of explicit formulae for the set of recoverable strains and for the relaxed energy of the system. These are governed by the mathematical notion of quasiconvexity. Here we focus on bounds on these quasiconvex hulls and envelopes in the setting of geometrically-linear elasticity. Firstly, we will present mathematical results on triples of transformation strains. This yields further insight into the quasiconvex hull of the twelve transformation strains in cubic-to-monoclinic phase transformations. Secondly, we consider bounds on the energy of such materials based on the so-called energy of mixing thus obtaining a lamination upper bound on the quasiconvex envelope of the energy. Here we present a new algorithm that yields improved upper bounds and allows us to relate numerical results for the lamination upper bound on the energy with theoretical inner bounds on the quasiconvex hull of triples of transformation strains.

  9. Introduction to the 2002 geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks: Chapter 2 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

    Science.gov (United States)

    ,

    2013-01-01

    The U.S Geological Survey (USGS) periodically conducts assessments of undiscovered oil and gas resources in the United States. The purpose of the U.S. Geological Survey National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The last major USGS assessment of oil and gas of the most important oil and gas provinces in the United States was in 1995 (Gautier and others, 1996). Since then a number of individual assessment provinces have been reappraised using new methodology. This was done particularly for those provinces where new information has become available, where new methodology was expected to reveal more insight to provide a better estimate, where additional geologic investigation was needed, or where continuous accumulations were deemed important. The San Juan Basin was reevaluated because of industry exploitation of new hydrocarbon accumulations that were not previously assessed and because of a change in application of assessment methodology to potential undiscovered hydrocarbon accumulations. Several changes have been made in this study. The methodology is different from that used in 1995 (Schmoker, 2003; Schmoker and Klett, 2003). In this study the total petroleum system (TPS) approach (Magoon and Dow, 1994) is used rather than the play approach. The Chama Basin is not included. The team of scientists studying the basin is different. The 1995 study focused on conventional accumulations, whereas in this 2002 assessment, it was a priority to assess continuous-type accumulations, including coal-bed gas. Consequently we are presenting here an entirely new study and results for the San Juan Basin Province. The results of this 2002 assessment of undiscovered oil and gas resources in the San Juan Basin Province (5022) are presented in this report within the geologic context of individual TPSs and their assessment units (AU) (table 1). Results

  10. Technical innovation and management

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Yang Cheol

    1982-08-15

    This book gives explanations of the conception of technical innovation, development plan in Korea, connection between technology and a growth factor in national income, problem of technical innovation in developing country, analysis on cooperation between a developed country and a developing country, evaluation and strategy of technical development in Korea, technical innovation of industry, management of technical industry, analysis of special condition in Korea.

  11. Technical innovation and management

    International Nuclear Information System (INIS)

    Yoon, Yang Cheol

    1982-08-01

    This book gives explanations of the conception of technical innovation, development plan in Korea, connection between technology and a growth factor in national income, problem of technical innovation in developing country, analysis on cooperation between a developed country and a developing country, evaluation and strategy of technical development in Korea, technical innovation of industry, management of technical industry, analysis of special condition in Korea.

  12. Strategy of technical innovation

    International Nuclear Information System (INIS)

    Lee, Ga Jong

    1990-12-01

    This book deals with policy of scientific technique and technical innovation such as research for development and types of technical innovation, historical development and process of technical innovation, economic growth, technology change and investment for research and development, structure and form of technical transfer with the meaning process, from, structure and theory, economic growth and investment of research and development with experiential analysis and case study on strategy of technical innovation in electron and fine chemical industry.

  13. Recoverability in quantum information theory

    Science.gov (United States)

    Wilde, Mark

    The fact that the quantum relative entropy is non-increasing with respect to quantum physical evolutions lies at the core of many optimality theorems in quantum information theory and has applications in other areas of physics. In this work, we establish improvements of this entropy inequality in the form of physically meaningful remainder terms. One of the main results can be summarized informally as follows: if the decrease in quantum relative entropy between two quantum states after a quantum physical evolution is relatively small, then it is possible to perform a recovery operation, such that one can perfectly recover one state while approximately recovering the other. This can be interpreted as quantifying how well one can reverse a quantum physical evolution. Our proof method is elementary, relying on the method of complex interpolation, basic linear algebra, and the recently introduced Renyi generalization of a relative entropy difference. The theorem has a number of applications in quantum information theory, which have to do with providing physically meaningful improvements to many known entropy inequalities. This is based on arXiv:1505.04661, now accepted for publication in Proceedings of the Royal Society A. I acknowledge support from startup funds from the Department of Physics and Astronomy at LSU, the NSF under Award No. CCF-1350397, and the DARPA Quiness Program through US Army Research Office award W31P4Q-12-1-0019.

  14. The role of technical progress in the process of recalculating oil reserves

    International Nuclear Information System (INIS)

    Boulard, J.N.

    1999-01-01

    Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

  15. Geologic framework for the assessment of undiscovered oil and gas resources in sandstone reservoirs of the Upper Jurassic-Lower Cretaceous Cotton Valley Group, U.S. Gulf of Mexico region

    Science.gov (United States)

    Eoff, Jennifer D.; Dubiel, Russell F.; Pearson, Ofori N.; Whidden, Katherine J.

    2015-01-01

    The U.S. Geological Survey (USGS) is assessing the undiscovered oil and gas resources in sandstone reservoirs of the Upper Jurassic–Lower Cretaceous Cotton Valley Group in onshore areas and State waters of the U.S. Gulf of Mexico region. The assessment is based on geologic elements of a total petroleum system. Four assessment units (AUs) are defined based on characterization of hydrocarbon source and reservoir rocks, seals, traps, and the geohistory of the hydrocarbon products. Strata in each AU share similar stratigraphic, structural, and hydrocarbon-charge histories.

  16. Technical Assistance Plan (TAP)

    Science.gov (United States)

    A Technical Assistance Plan (TAP) enables community groups to retain the services of an independent technical advisor and to provide resources for a community group to help inform other community members about site decisions.

  17. Technical report writing

    Science.gov (United States)

    Vidoli, Carol A.

    1992-01-01

    This manual covers the fundamentals of organizing, writing, and reviewing NASA technical reports. It was written to improve the writing skills of LeRC technical authors and the overall quality of their reports.

  18. Technical Report Writing Today

    DEFF Research Database (Denmark)

    Riordan, Daniel G.

    2014-01-01

    Section 1: Technical Communication Basics (8 chapters on tech com, audiences, tech com process, tech com style, researching, designing pages, using visual aids, describing). Section 2: Technical Communication Applications (7 chapters on sets of instructions, informal reports and email, developing...

  19. Technical training: places available

    CERN Document Server

    2013-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

  20. Technical training - places available

    CERN Document Server

    2013-01-01

    If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

  1. Technical training: places available

    CERN Multimedia

    2013-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tél : 74924)  

  2. VANDAL technical overview

    International Nuclear Information System (INIS)

    Unsworth, M.D.

    1989-07-01

    This document is concerned with the technicalities of the VANDAL code and covers the technical details of each of the systems modules in turn. Covered are SAMPLING, FLOW, VAULT, GEOSPHERE, BIOSPHERE and TIMESTEPPING. (author)

  3. Technical training: places available

    CERN Multimedia

    2014-01-01

    If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

  4. Technical training: places available

    CERN Multimedia

    2014-01-01

    If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Marie Lahchimi, Technical Training Administration (Tel: 74924)

  5. Handbook of Technical Communication

    OpenAIRE

    Mehler , Alexander; Romary , Laurent; Gibbon , Dafydd

    2012-01-01

    International audience; The handbook "Technical Communication" brings together a variety of topics which range from the role of technical media in human communication to the linguistic, multimodal enhancement of present-day technologies. It covers the area of computer-mediated text, voice and multimedia communication as well as of technical documentation. In doing so, the handbook takes professional and private communication into account. Special emphasis is put on technical communication bas...

  6. Assessment of Appalachian basin oil and gas resources: Devonian gas shales of the Devonian Shale-Middle and Upper Paleozoic Total Petroleum System: Chapter G.9 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Milici, Robert C.; Swezey, Christopher S.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    This report presents the results of a U.S. Geological Survey (USGS) assessment of the technically recoverable undiscovered natural gas resources in Devonian shale in the Appalachian Basin Petroleum Province of the eastern United States. These results are part of the USGS assessment in 2002 of the technically recoverable undiscovered oil and gas resources of the province. This report does not use the results of a 2011 USGS assessment of the Devonian Marcellus Shale because the area considered in the 2011 assessment is much greater than the area of the Marcellus Shale described in this report. The USGS assessment in 2002 was based on the identification of six total petroleum systems, which include strata that range in age from Cambrian to Pennsylvanian. The Devonian gas shales described in this report are within the Devonian Shale-Middle and Upper Paleozoic Total Petroleum System, which extends generally from New York to Tennessee. This total petroleum system is divided into ten assessment units (plays), four of which are classified as conventional and six as continuous. The Devonian shales described in this report make up four of these continuous assessment units. The assessment results are reported as fully risked fractiles (F95, F50, F5, and the mean); the fractiles indicate the probability of recovery of the assessment amount. The products reported are oil, gas, and natural gas liquids. The mean estimates for technically recoverable undiscovered hydrocarbons in the four gas shale assessment units are 12,195.53 billion cubic feet (12.20 trillion cubic feet) of gas and 158.91 million barrels of natural gas liquids

  7. Teaching Technical Writing - Towards Technical Writing

    DEFF Research Database (Denmark)

    Kastberg, Peter

    2000-01-01

    In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm that ...... of technical writing.......In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm...... that used to govern what the quality of an LSP text should be as opposed to the standpoint, which I advocate. By way of summing up, I will show how a university curriculum is designed so that - upon graduation - the technical translator could also be methodological quite well suited to take on the challenge...

  8. Technical rules in law

    Energy Technology Data Exchange (ETDEWEB)

    Debelius, J

    1978-08-01

    An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself.

  9. Technical rules in law

    International Nuclear Information System (INIS)

    Debelius, J.

    1978-01-01

    An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself. (orig.) [de

  10. Water and Proppant Requirements and Water Production Associated with Undiscovered Petroleum in the Bakken and Three Forks Formations, North Dakota and Montana, USA

    Science.gov (United States)

    Haines, S. S.; Varela, B. A.; Thamke, J.; Hawkins, S. J.; Gianoutsos, N. J.; Tennyson, M. E.

    2017-12-01

    Water is used for several stages of oil and gas production, in particular for hydraulic fracturing that is typically used during production of petroleum from low-permeability shales and other rock types (referred to as "continuous" petroleum accumulations). Proppant, often sand, is also consumed during hydraulic fracturing. Water is then produced from the reservoir along with the oil and gas, representing either a disposal consideration or a possible source of water for further petroleum development or other purposes. The U.S. Geological Survey (USGS) has developed an approach for regional-scale estimation of these water and proppant quantities in order to provide an improved understanding of possible impacts and to help with planning and decision-making. Using the new methodology, the USGS has conducted a quantitative assessment of water and proppant requirements, and water production volumes, associated with associated with possible future production of undiscovered petroleum resources in the Bakken and Three Forks Formations, Williston Basin, USA. This water and proppant assessment builds directly from the 2013 USGS petroleum assessment for the Bakken and Three Forks Formations. USGS petroleum assessments incorporate all available geologic and petroleum production information, and include the definition of assessment units (AUs) that specify the geographic regions and geologic formations for the assessment. The 2013 petroleum assessment included 5 continuous AUs for the Bakken Formation and one continuous AU for the Three Forks Formation. The assessment inputs are defined probabilistically, and a Monte Carlo approach provides outputs that include uncertainty bounds. We can summarize the assessment outputs with the mean values of the associated distributions. The mean estimated total volume of water for well drilling and cement for all six continuous AUs is 5.9 billion gallons, and the mean estimated volume of water for hydraulic fracturing for all AUs is 164

  11. Petroleum systems and geologic assessment of undiscovered oil and gas, Cotton Valley group and Travis Peak-Hosston formations, East Texas basin and Louisiana-Mississippi salt basins provinces of the northern Gulf Coast region. Chapters 1-7.

    Science.gov (United States)

    ,

    2006-01-01

    The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Cotton Valley Group and Travis Peak and Hosston Formations in the East Texas Basin and Louisiana-Mississippi Salt Basins Provinces in the Gulf Coast Region (USGS Provinces 5048 and 5049). The Cotton Valley Group and Travis Peak and Hosston Formations are important because of their potential for natural gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and eight assessment units. Seven assessment units were quantitatively assessed for undiscovered oil and gas resources.

  12. Assessment of Undiscovered Deposits of Gold, Silver, Copper, Lead, and Zinc in the United States: A Portable Document (PDF) Recompilation of USGS Open-File Report 96-96 and Circular 1178

    Science.gov (United States)

    U.S. Geological Survey National Mineral Resource Assessment Team Recompiled by Schruben, Paul G.

    2002-01-01

    This publication contains the results of a national mineral resource assessment study. The study (1) identifies regional tracts of ground believed to contain most of the nation's undiscovered resources of gold, silver, copper, lead, and zinc in conventional types of deposits; and (2) includes probabilistic estimates of the amounts of these undiscovered resources in most of the tracts. It also contains a table of the significant known deposits in the tracts, and includes descriptions of the mineral deposit models used for the assessment. The assessment was previously released in two major publications. The conterminous United States assessment was published in 1996 as USGS Open-File Report 96-96. Subsequently, the Alaska assessment was combined with the conterminous assessment in 1998 and released as USGS Circular 1178. This new recompilation was undertaken for several reasons. First, the graphical browser software used in Circular 1178 was ONLY compatible with the Microsoft Windows operating system. It was incompatible with the Macintosh operating system, Linux, and other types of Unix computers. Second, the browser on Circular 1178 is much less intuitive to operate, requiring most users to follow a tutorial to understand how to navigate the information on the CD. Third, this release corrects several errors and numbering inconsistencies in Circular 1178.

  13. Writing a technical note.

    Science.gov (United States)

    Ng, K H; Peh, W C G

    2010-02-01

    A technical note is a short article giving a brief description of a specific development, technique or procedure, or it may describe a modification of an existing technique, procedure or device applicable to medicine. The technique, procedure or device described should have practical value and should contribute to clinical diagnosis or management. It could also present a software tool, or an experimental or computational method. Technical notes are variously referred to as technical innovations or technical developments. The main criteria for publication will be the novelty of concepts involved, the validity of the technique and its potential for clinical applications.

  14. Technical Elements (CCT1)

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

    2017-01-01

    Many of the aspects dealt with in the CA EPBD are closely interlinked with each other and may refer to both new and existing buildings, as well as to inspection and certification. This is also true for technical aspects, such as the calculation methodologies, and how to include technical systems......’ efficiency or how to integrate renewable energy within them. The central team for Technical Elements deals with issues of a technical nature, which are common to new and existing buildings, and/or with minimum demands, certification and inspection. This report focuses on the implementation of Articles 3, 4...

  15. Resource Assessment of the In-Place and Potentially Recoverable Deep Natural Gas Resource of the Onshore Interior Salt Basins, North Central and Northeastern Gulf of Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ernest A. Mancini

    2006-09-30

    rock from depths below 12,000 feet in this basin is 4,800 TCF. Assuming an expulsion, migration and trapping efficiency of 1 to 5%, 48 to 240 TCF of gas is potentially available. The final recoverable gas is some percent of this estimated thermogenic gas resource based on the recovery factor for the specific reservoir. To date, some 29 TCF of gas have been produced from this basin. Also, the thermogenic gas, whether generated from late secondary cracking of oil to gas in the source rock or from oil to gas conversion in deeply buried reservoirs, migrated updip into shallower reservoirs, including the Monroe gas rock at depths of some 2,000 feet.

  16. Technical Training for Managers.

    Science.gov (United States)

    Haverland, Edgar M.

    The question has arisen as to what kind of information a manager without extensive technical training needs to learn to supervise effectively. For example, the Nike Hercules fire control platoon leader, usually an officer in his first active duty assignment, seldom has had extensive technical training. Yet he is responsibile for the…

  17. Technical Manual. The ACT®

    Science.gov (United States)

    ACT, Inc., 2014

    2014-01-01

    This manual contains technical information about the ACT® college readiness assessment. The principal purpose of this manual is to document the technical characteristics of the ACT in light of its intended purposes. ACT regularly conducts research as part of the ongoing formative evaluation of its programs. The research is intended to ensure that…

  18. Developing Technical Skill Assessments

    Science.gov (United States)

    Hyslop, Alisha

    2009-01-01

    One of the biggest challenges facing the career and technical education (CTE) community as it works to implement the 2006 Perkins Act is responding to more rigorous requirements for reporting on CTE students' technical skill attainment. The U.S. Department of Education suggested in non-regulatory guidance that states and locals use the number of…

  19. Transformation of technical infrastructure

    DEFF Research Database (Denmark)

    Nielsen, Susanne Balslev

    1998-01-01

    article about the need of new planning forums in order to initiate transformations with in management of large technical systems for energy, waste and water supply.......article about the need of new planning forums in order to initiate transformations with in management of large technical systems for energy, waste and water supply....

  20. TRANSLATING SERVICE TECHNICAL PROSE

    African Journals Online (AJOL)

    language. The Application of Technical Service. Prose. To form a good idea of the appl ication .... cost lives. In this particular domain, translators must have a sound technical ... These semantic ... another language and often, in doing so, changing its meaning. The words ..... He will hand out tasks to each translator and after.

  1. Technical Writing Tips

    Science.gov (United States)

    Kennedy, Patrick M.

    2004-01-01

    The main reason engineers, technicians, and programmers write poor technical documents is because they have had little training or experience in that area. This article addresses some of the basics that students can use to master technical writing tasks. The article covers the most common problems writers make and offers suggestions for improving…

  2. Research in Technical Colleges

    Science.gov (United States)

    MacLennan, A.

    2008-01-01

    Purpose: The purpose of this paper is to list and demonstrate areas in which research needs to be carried out, or questions answered, in order to raise the quality of technical education. Design/methodology/approach: The area of technical education expanded very rapidly in the late 1950s, and there was little comprehensive knowledge regarding the…

  3. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Glasser, Alan H. [Fusion Theory and Computation Inc., Kingston, WA (United States)

    2018-02-02

    Final technical report on DE-SC0016106. This is the final technical report for a portion of the multi-institutional CEMM project. This report is centered around 3 publications and a seminar presentation, which have been submitted to E-Link.

  4. Technical Agency in Practice

    DEFF Research Database (Denmark)

    Krummheuer, Antonia Lina

    2015-01-01

    ) description of hybrid networks in which human and non-human actants are granted agency without differentiating different kinds of agency, EMCA focuses on the member's perspectives and the situated construction of technical agency that is made relevant within an ongoing interaction. Based on an EMCA analysis......The paper combines the discussion of technical agency and hybrid networks of Actor-Network Theory (ANT) with an ethnomethodological/conversation analytical (EMCA) perspective on situated practices in which participants ascribe agency to technical artefacts. While ANT works with (ethnographic...... of three video recordings of situations in which technical agency is made relevant by the human participants, the paper demonstrates different ways in which agency is granted to technical artefacts. Human participants can treat a technology as communication partner, as an active part (and actant...

  5. Executive Summary -- assessment of undiscovered oil and gas resources of the San Joaquin Basin Province of California, 2003: Chapter 1 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

    Science.gov (United States)

    Gautier, Donald L.; Scheirer, Allegra Hosford; Tennyson, Marilyn E.; Peters, Kenneth E.; Magoon, Leslie B.; Lillis, Paul G.; Charpentier, Ronald R.; Cook, Troy A.; French, Christopher D.; Klett, Timothy R.; Pollastro, Richard M.; Schenk, Christopher J.

    2007-01-01

    In 2003, the U.S. Geological Survey (USGS) completed an assessment of the oil and gas resource potential of the San Joaquin Basin Province of California (fig. 1.1). The assessment is based on the geologic elements of each Total Petroleum System defined in the province, including hydrocarbon source rocks (source-rock type and maturation and hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined five total petroleum systems and ten assessment units within these systems. Undiscovered oil and gas resources were quantitatively estimated for the ten assessment units (table 1.1). In addition, the potential was estimated for further growth of reserves in existing oil fields of the San Joaquin Basin.

  6. Towards common technical standards

    International Nuclear Information System (INIS)

    Rahmat, H.; Suardi, A.R.

    1993-01-01

    In 1989, PETRONAS launched its Total Quality Management (TQM) program. In the same year the decision was taken by the PETRONAS Management to introduce common technical standards group wide. These standards apply to the design, construction, operation and maintenance of all PETRONAS installations in the upstream, downstream and petrochemical sectors. The introduction of common company standards is seen as part of an overall technical management system, which is an integral part of Total Quality Management. The Engineering and Safety Unit in the PETRONAS Central Office in Kuala Lumpur has been charged with the task of putting in place a set of technical standards throughout PETRONAS and its operating units

  7. Technical standards in nuclear area

    International Nuclear Information System (INIS)

    Grimberg, M.

    1978-01-01

    The technical standardization in nuclear area is discussed. Also, the competence of CNEN in standardization pursuit is analysed. Moreover, the process of working up of technical standards is explained; in addition, some kinds of technical standards are discussed. (author) [pt

  8. SAM Technical Contacts

    Science.gov (United States)

    These technical contacts are available to help with questions regarding method deviations, modifications, sample problems or interferences, quality control requirements, the use of alternative methods, or the need to address analytes or sample types.

  9. INDOT Technical Training Plan

    Science.gov (United States)

    2012-04-01

    The study provides the background documents necessary for the development of a Technical Training Plan and makes recommendations : for the content and structure of such a plan for the District Operations, Operations, Capital Program Management, and E...

  10. social & technical innovations

    International Development Research Centre (IDRC) Digital Library (Canada)

    CHANGE: GAPS BRIDGED BY SMART SOLUTIONS. CHALLENGE: INABILITY TO REACH THOSE IN NEED. SOLAR PANELS. OVERCOME POWER. SUPPLY CHALLENGES. IN BURKINA FASO. SOCIAL & TECHNICAL. INNOVATIONS. BANGLADESH BURKINA FASO ETHIOPIA KENYA LEBANON PERU VIETNAM.

  11. Superfund Technical Assistance Grants

    Data.gov (United States)

    U.S. Environmental Protection Agency — This asset includes data related to the Superfund Technical Assistance Grant program, including grant number, award amounts, award dates, period of performance,...

  12. OSH technical reference manual

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  13. NCDC Technical Reports

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NCDC Technical Reports is a set of retrospective analyses produced by the Research Customer Service Group and the National Climatic Data Center from 1995 to 2008....

  14. Socio-technical Betwixtness

    DEFF Research Database (Denmark)

    Bossen, Claus

    2017-01-01

    the intrinsically social and technical interwovenness of design, and the necessity of including affected people and stakeholders in the design process. This betwixtness of socio-technical design is demonstrated by the analysis of two IT systems for healthcare: a foundational model for electronic healthcare records......This chapter focusses on two challenges for socio-technical design: Having to choose between different rationales for design, and the adequate understanding and depiction of the work to be redesigned. These two challenges betwixt the otherwise strong tenets of socio-technical design of pointing out......, and an IT system organizing hospital porters’ work. The conceptual background for the analysis of the cases is provided by a short introduction to different rationales for organizational design, and by pointing to the differences between a linear, rationalistic versus an interactional depiction of work....

  15. Technical report writing today

    CERN Document Server

    Riordan, Daniel G

    2014-01-01

    "Technical Report Writing Today" provides thorough coverage of technical writing basics, techniques, and applications. Through a practical focus with varied examples and exercises, students internalize the skills necessary to produce clear and effective documents and reports. Project worksheets help students organize their thoughts and prepare for assignments, and focus boxes highlight key information and recent developments in technical communication. Extensive individual and collaborative exercises expose students to different kinds of technical writing problems and solutions. Annotated student examples - more than 100 in all - illustrate different writing styles and approaches to problems. Numerous short and long examples throughout the text demonstrate solutions for handling writing assignments in current career situations. The four-color artwork in the chapter on creating visuals keeps pace with contemporary workplace capabilities. The Tenth Edition offers the latest information on using electronic resum...

  16. The technical supervision interface

    CERN Document Server

    Sollander, P

    1998-01-01

    The Technical Control Room (TCR) is currently using 30 different applications for the remote supervision of the technical infrastructure at CERN. These applications have all been developed with the CERN made Uniform Man Machine Interface (UMMI) tools built in 1990. However, the visualization technology has evolved phenomenally since 1990, the Technical Data Server (TDS) has radically changed our control system architecture, and the standardization and the maintenance of the UMMI applications have become important issues as their number increases. The Technical Supervision Interface is intended to replace the UMMI and solve the above problems. Using a standard WWW-browser for the display, it will be inherently multi-platform and hence available for control room operators, equipment specialists and on-call personnel.

  17. Training for Technical Assistants: Technical Assistance Program

    Science.gov (United States)

    1986-09-01

    shortage of technical ptfesson until such time as English , "speking instructors might be trained, There. would be An aumcation of committed on-calI...12 hours in classroom Instruction, students in English as a Second nel Research and Development Computer.taught students Language. The program Is...hbeels "p.-ogram. A Iot ’ atar boiler arn tank heats týe food enroute to its destination. 1.0. A new tor of dust ptectleon to protect machine .perators

  18. 78 FR 27963 - Reliability Technical Conference; Notice of Technical Conference

    Science.gov (United States)

    2013-05-13

    ... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, July 9, 2013 from 9:00 a.m. to 5:00 p.m. This... technical support for webcasts and offers the option of listening to the meeting via phone-bridge for a fee...

  19. 76 FR 64083 - Reliability Technical Conference; Notice of Technical Conference

    Science.gov (United States)

    2011-10-17

    ... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, November 29, 2011, from 1 p.m. to 5 p.m. and... reliability that were identified in earlier Commission technical conferences. The conference also will discuss...

  20. Technical training: places available

    CERN Document Server

    2013-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924)   Electronics design Next Session Duration Language Introduction to VHDL 21-Feb-13 to 22-Feb-13 2 days English Mechanical design Next Session Duration Language ANSYS - Introduction à ANSYS Mechanical APDL 04-Feb-13 to 07-Feb-13 4 days English Applications de la cotation fonctionnelle et du langage ISO 06-Feb-13 to 08-Feb-13 2 days 4 hours French CATIA V5 – Surfacique 14-Jan-13 to 15-Jan-13 2 days French Office software Next Session Duration Language ACCESS 2010 - niveau 2 : ECDL 06-Feb-13 to 07-Feb-13 2 days French Dreamweaver CS3 - Niveau 1 14-Jan-13 to 15-Jan-13 2 d...

  1. Technical training - Places available

    CERN Document Server

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924)   Electronics design Next Session Duration Language Availability Certified LabVIEW Associate Developer (CLAD) 06-Dec-12 to 06-Dec-12 1 hour English One more place available Compatibilité électromagnetique (CEM): Applications 23-Nov-12 to 23-Nov-12 3.5 hours English 3 places available Compatibilité électromagnétique (CEM): Introduction 23-Nov-12 to 23-Nov-12 3 hours English 43 places available Effets des Radiations sur les composants et systèmes électroniques 11-Dec-12 to 12-Dec-12 1 day 4 hours French 9 places available LabVIEW for beginners ...

  2. Technical training - places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924) HR Department »Electronics design Next Session Duration Language Availability Comprehensive VHDL for FPGA Design 08-Oct-12 to 12-Oct-12 5 days English 3 places available Foundations of Electromagnetism and Magnet Design (EMAG) 14-Nov-12 to 27-Nov-12 6 days English 20 places available Impacts de la suppression du plomb (RoHS) en électronique 26-Oct-12 to 26-Oct-12 8 hours French 15 places available Introduction to VHDL 10-Oct-12 to 11-Oct-12 2 days English 7 places available LabVIEW Real Time and FPGA 13-Nov-12 to 16-Nov-12 5 days French 5 places available »Mechanical design Next Se...

  3. Problems of technical cooperation

    International Nuclear Information System (INIS)

    Noramli, M.

    1987-01-01

    The main principles of the IAEA technical co-operation program, which intends to answer the requirements of the member states as regards technical assistance, are presented. IAEA offers its assistance in the supervision and financial support of the projects, which promise direct and quick profit to the member states. Projects related to the satisfaction of the main demands of humanity, industrial use, energy generation, radiation protection and other fields, which can promote the contribution of nuclear power generation to the course of peace, protection of health and thriving of states, are among them. 35 million dollars (USA) was allocated for the IAEA technical assistance and realization of the co-operation program in 1987

  4. Fuel Element Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Burley, H.H. [ed.

    1956-08-01

    It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

  5. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2009-01-01

    Are you running Vista on your new PC – or are you planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual session of this course will take place on 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at mailto:Technical.Training@cern.ch

  6. Transformation of technical infrastructure

    DEFF Research Database (Denmark)

    Nielsen, Susanne Balslev

    , the evolution of large technological systems and theories about organisational and technological transformationprocesses. The empirical work consist of three analysis at three different levels: socio-technical descriptions of each sector, an envestigation of one municipality and envestigations of one workshop......The scope of the project is to investigate the possibillities of - and the barriers for a transformation of technical infrastructure conserning energy, water and waste. It focus on urban ecology as a transformation strategy. The theoretical background of the project is theories about infrastructure...

  7. KSC Technical Capabilities Website

    Science.gov (United States)

    Nufer, Brian; Bursian, Henry; Brown, Laurette L.

    2010-01-01

    This document is the website pages that review the technical capabilities that the Kennedy Space Center (KSC) has for partnership opportunities. The purpose of this information is to make prospective customers aware of the capabilities and provide an opportunity to form relationships with the experts at KSC. The technical capabilities fall into these areas: (1) Ground Operations and Processing Services, (2) Design and Analysis Solutions, (3) Command and Control Systems / Services, (4) Materials and Processes, (5) Research and Technology Development and (6) Laboratories, Shops and Test Facilities.

  8. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    Are you running Vista on your new PC – or are planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual sessions of this course will take place on 12 December 2008 and 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at Technical.Training@cern.ch

  9. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    You are running Vista on your new PC – or are planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual sessions of this course will take place on 12 December 2008 and 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at mailto:Technical.Training@cern.ch

  10. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    Are you running Vista on your new PC – or are you planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual sessions of this course will take place on 12 December 2008 and 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at mailto:Technical.Training@cern.ch

  11. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    You are running Vista on your new PC – or are planning to install it? The Technical Training service is organizing a half-day training on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced using Windows XP. The next bilingual sessions of this course will take place on December 12, 2008 and January 30, 2009. Register using our catalogue : http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at Technical.Training@cern.ch

  12. Technical memory 2007

    International Nuclear Information System (INIS)

    2009-01-01

    The technical memory 2007 of the Nuclear Regulatory Authority (ARN) of the Argentine Republic, compiles the papers published in the subject on radiation protection and nuclear safety, and presented in journals, technical reports, congress or meetings of these specialities by personnel of the mentioned institution during 2007. In this edition the documents are presented on: environmental protection; transport of radioactive materials; regulations; research reactors and nuclear power plants; biological radiation effects; therapeutic uses of ionizing radiation and radioprotection of patients; internal dosimetry; physical dosimetry; knowledge management; radioactive waste management [es

  13. Routledge French technical dictionary

    CERN Document Server

    1994-01-01

    The French-English volume of this highly acclaimed set consists of some 100,000 keywords in both French and English, drawn from the whole range of modern applied science and technical terminology. Covers over 70 subject areas, from engineering and chemistry to packaging, transportation, data processing and much more.

  14. Technical objectives of inspection

    International Nuclear Information System (INIS)

    Sorenson, R.J.; Stewart, K.B.; Schneider, R.A.

    1976-01-01

    The various technical objectives of inspection are discussed in a very general manner. The discussion includes how the inspection function is related to the assumed threat, the various degrees of assurance and reliance on criteria, and the hierarchy of assurance which is obtained from the various types or levels of inspection

  15. NUSC Technical Publications Guide.

    Science.gov (United States)

    1985-05-01

    Facility personnel especially that of A. Castelluzzo, E. Deland, J. Gesel , and E. Szlosek (all of Code 4343). Reviewed and Approved: 14 July 1980 D...their technical content and format. Review and approve the manual outline, the review manuscript, and the final camera - reproducible copy. Conduct in

  16. ITER EDA technical activities

    International Nuclear Information System (INIS)

    Aymar, R.

    1998-01-01

    Six years of technical work under the ITER EDA Agreement have resulted in a design which constitutes a complete description of the ITER device and of its auxiliary systems and facilities. The ITER Council commented that the Final Design Report provides the first comprehensive design of a fusion reactor based on well established physics and technology

  17. Technical basis of safeguards

    International Nuclear Information System (INIS)

    Buechler, C.

    1975-01-01

    Definition of nuclear materials control. Materials accountancy and physical control as technical possibilities. Legal possibilities and levels of responsibility: material holders, national and international authority. Detection vs. prevention. Physical security and containment surveillance. Accountancy: materials balance concept. Materials measurement: inventory taking, flow determination. IAEA safeguards; verification of operator's statement. (HP) [de

  18. Technical memory 1999

    International Nuclear Information System (INIS)

    2000-01-01

    The technical memory 1999 of the Nuclear Regulatory Authority (NRA) of the Argentine Republic, compile the papers published in the subject on radiation protection and nuclear safety, safeguards and physical protection, and presented in congress or meetings of these specialities by personnel of the mentioned institution during 1999

  19. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) IT3T/1 - Read your mail and more with Outlook 2003 : 14.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/2 - Creating, managing and using distribution lists with Simba2 : 16.6.2005 (IT Technical Training Tutorial, free of charge) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP : 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003 : 30.6.2005 (IT Technical Training Tutorial, free of charge) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoC...

  20. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    John Ross

    2003-04-30

    The Final Technical Report summarizes research accomplishments and Publications in the period of 5/1/99 to 4/30/03 done on the grant. Extensive progress was made in the period covered by this report in the areas of chemical kinetics of non-linear systems; spatial structures, reaction - diffusion systems, and thermodynamic and stochastic theory of electrochemical and general systems.

  1. Materials Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-08-01

    Roadmap identifying the efforts of the Materials Technical Team (MTT) to focus primarily on reducing the mass of structural systems such as the body and chassis in light-duty vehicles (including passenger cars and light trucks) which enables improved vehicle efficiency regardless of the vehicle size or propulsion system employed.

  2. Technical Writing in Hydrogeology.

    Science.gov (United States)

    Tinker, John R., Jr.

    1986-01-01

    A project for Writing Across the Curriculum at the University of Wisconsin-Eau Claire is described as a method to relate the process of writing to the process of learning hydrology. The project focuses on an actual groundwater contamination case and is designed to improve the technical writing skills of students. (JN)

  3. Review of technical specifications

    International Nuclear Information System (INIS)

    Bedrich, M.; Scholz, D.

    1980-01-01

    The present paper deals with position and function of technical specifications before and during the manufacturing of reactor components, their structure and reasons for specific regulations due to safety philosophy and explains the cooperation of supplier, manufacturer, utilities and supervisory organizations. (RW)

  4. PISA 2009 Technical Report

    Science.gov (United States)

    OECD Publishing (NJ1), 2012

    2012-01-01

    The "PISA 2009 Technical Report" describes the methodology underlying the PISA 2009 survey. It examines additional features related to the implementation of the project at a level of detail that allows researchers to understand and replicate its analyses. The reader will find a wealth of information on the test and sample design,…

  5. PISA 2012 Technical Report

    Science.gov (United States)

    OECD Publishing, 2014

    2014-01-01

    The "PISA 2012 Technical Report" describes the methodology underlying the PISA 2012 survey, which tested 15-year-olds' competencies in mathematics, reading and science and, in some countries, problem solving and financial literacy. It examines the design and implementation of the project at a level of detail that allows researchers to…

  6. New usable technical specifications

    International Nuclear Information System (INIS)

    Webster, S.A.; Tomasi, L.T.; Bernier, R.A.

    1989-01-01

    After 2 yr of preparation, 1988 finally saw the nuclear industry writing operator-oriented technical specifications. This effort is a continuation of previous efforts to develop improved and usable standard technical specifications (STSs), and is being conducted by the four nuclear steam supply system vendor owners' groups under the auspices of the Nuclear Management Resources Council. Each participant is currently preparing a set of improved STSs based on a writer's guide that was developed through a combined industry effort. In May of 1987, a Human Factors Improvements to Technical Specifications (HFITS) task group was formed to prepare a writer's guide for improved, industrywide STSs. This task group was composed of two representatives from each owners' group, one with a human factors background and one with some operations background. Two documents were prepared in 6 months, a human factors report laying the groundwork for the considerations to go into technical specifications and a writer's guide for their preparation. This paper reports on the application of this writer's guide to the writing of improved STS

  7. The role of technical progress in the process of recalculating oil reserves; Le role du progres technique dans le processus de renouvellement des reserves petrolieres

    Energy Technology Data Exchange (ETDEWEB)

    Boulard, J.N. [Total/Fina/Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

    1999-08-01

    Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

  8. Methods of analysis by the U.S. Geological Survey National Water Quality Laboratory; determination of whole-water recoverable arsenic, boron, and vanadium using inductively coupled plasma-mass spectrometry

    Science.gov (United States)

    Garbarino, John R.

    2000-01-01

    Analysis of in-bottle digestate by using the inductively coupled plasma?mass spectrometric (ICP?MS) method has been expanded to include arsenic, boron, and vanadium. Whole-water samples are digested by using either the hydrochloric acid in-bottle digestion procedure or the nitric acid in-bottle digestion procedure. When the hydrochloric acid in-bottle digestion procedure is used, chloride must be removed from the digestate by subboiling evaporation before arsenic and vanadium can be accurately determined. Method detection limits for these elements are now 10 to 100 times lower than U.S. Geological Survey (USGS) methods using hydride generation? atomic absorption spectrophotometry (HG? AAS) and inductively coupled plasma? atomic emission spectrometry (ICP?AES), thus providing lower variability at ambient concentrations. The bias and variability of the methods were determined by using results from spike recoveries, standard reference materials, and validation samples. Spike recoveries in reagent-water, surface-water, ground-water, and whole-water recoverable matrices averaged 90 percent for seven replicates; spike recoveries were biased from 25 to 35 percent low for the ground-water matrix because of the abnormally high iron concentration. Results for reference material were within one standard deviation of the most probable value. There was no significant difference between the results from ICP?MS and HG?AAS or ICP?AES methods for the natural whole-water samples that were analyzed.

  9. One-pot hydrothermal synthesis and characterization of CoFe{sub 2}O{sub 4} nanoparticles and its application as magnetically recoverable catalyst in oxidation of alcohols by periodic acid

    Energy Technology Data Exchange (ETDEWEB)

    Paul, Bappi; Purkayastha, Debraj Dhar; Dhar, Siddhartha Sankar, E-mail: ssd_iitg@hotmail.com

    2016-09-15

    A novel and facile approach for one-pot synthesis of spinel cobalt ferrite (CoFe{sub 2}O{sub 4}) nanoparticles (NPs) is presented here. The synthesis involves homogeneous chemical precipitation followed by hydrothermal heating, using tributylamine (TBA) as a hydroxylating agent. Polyethylene glycol (PEG) 4000 was used as surfactant. As-synthesized CoFe{sub 2}O{sub 4} NPs were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), N{sub 2} adsorption-desorption isotherm (BET) and vibrating sample magnetometry (VSM). TEM image showed formation of spherical particles of sizes 2–30 nm. These NPs were used as magnetically recoverable catalyst in oxidation of alcohols to their corresponding aldehydes by periodic acid. This oxidative procedure is found to be highly efficient affording products in very high yield and selectivity. The easy magnetic separation of the catalyst and efficient reusability are key features of this methodology. - Highlights: • Hydrothermal synthesis of CoFe{sub 2}O{sub 4} NPs with (C{sub 4}H{sub 9}){sub 3}N as hydroxylating agent. • The TEM images showed the particles to be spherical in shape with sizes 2–30 nm. • CoFe{sub 2}O{sub 4} was used as recyclable catalyst for oxidation of alcohols by periodic acid.

  10. One-pot hydrothermal synthesis and characterization of CoFe2O4 nanoparticles and its application as magnetically recoverable catalyst in oxidation of alcohols by periodic acid

    International Nuclear Information System (INIS)

    Paul, Bappi; Purkayastha, Debraj Dhar; Dhar, Siddhartha Sankar

    2016-01-01

    A novel and facile approach for one-pot synthesis of spinel cobalt ferrite (CoFe 2 O 4 ) nanoparticles (NPs) is presented here. The synthesis involves homogeneous chemical precipitation followed by hydrothermal heating, using tributylamine (TBA) as a hydroxylating agent. Polyethylene glycol (PEG) 4000 was used as surfactant. As-synthesized CoFe 2 O 4 NPs were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), N 2 adsorption-desorption isotherm (BET) and vibrating sample magnetometry (VSM). TEM image showed formation of spherical particles of sizes 2–30 nm. These NPs were used as magnetically recoverable catalyst in oxidation of alcohols to their corresponding aldehydes by periodic acid. This oxidative procedure is found to be highly efficient affording products in very high yield and selectivity. The easy magnetic separation of the catalyst and efficient reusability are key features of this methodology. - Highlights: • Hydrothermal synthesis of CoFe 2 O 4 NPs with (C 4 H 9 ) 3 N as hydroxylating agent. • The TEM images showed the particles to be spherical in shape with sizes 2–30 nm. • CoFe 2 O 4 was used as recyclable catalyst for oxidation of alcohols by periodic acid.

  11. National inventory of radioactive wastes and recoverable materials 2006. Descriptive catalogue of radioactive waste families; Inventaire national des dechets radioactifs et des matieres valorisables 2006. Catalogue descriptif des familles de dechets radioactifs

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    Real comprehensive overview of radioactive wastes, the national inventory of radioactive wastes and recoverable materials describes the situation in France of the wastes that can be conditioned (in their definitive form) or not. It presents also the waste production quantities foreseen for 2010, 2020 and beyond. This document is a complement to the synthesis report and to the geographic inventory of radioactive wastes in France and details the classification of wastes by families (wastes with similar characteristics). For each family of wastes, the description comprises a general presentation and some photos. It comprises also some data such as the position of the family in the French classification, the industrial activity at the origin of the waste, the production situation of the waste in concern (finished, in progress, not started). Some information about the raw waste are given and the conditioning process used is described. Some figures complete the description, like: the past and future production quantities, the evaluation of the radioactivity of the waste family in 2004 and 2020, and the evaluation of the thermal power when available. Finally, some information are given about the presence of compounds with a specific risk of toxicity. (J.S.)

  12. Bioethics for Technical Experts

    Science.gov (United States)

    Asano, Shigetaka

    Along with rapidly expanding applications of life science and technology, technical experts have been implicated more and more often with ethical, social, and legal problems than before. It should be noted that in this background there are scientific and social uncertainty elements which are inevitable during the progress of life science in addition to the historically-established social unreliability to scientists and engineers. In order to solve these problems, therefore, we should establish the social governance with ‘relief’ and ‘reliance’ which enables for both citizens and engineers to share the awareness of the issues, to design social orders and criterions based on hypothetical sense of values for bioethics, to carry out practical use management of each subject carefully, and to improve the sense of values from hypothetical to universal. Concerning these measures, the technical experts can learn many things from the present performance in the medical field.

  13. Sources of technical assistance

    International Nuclear Information System (INIS)

    Laue, H.J.

    1977-01-01

    This paper shows examples of technical assistance programmes within bilateral cooperation agreements between the Federal Republic of Germany and a number of developing countries of very different characteristics and summarizes the possibilities of technical assistance granted by international organizations, such as IAEA, UNDP, etc. A basic requirement for a successful transfer of technology is a high knowledge level of the indigenous scientists and engineers. Therefore, programmes for training and education and for information exchange are presented. Based on these, the means and methods of planning, performance and quality assurance are explained by practical examples and are related to the progress achieved in the use of nuclear energy and in establishing a national industry in the developing countries. (orig.) [de

  14. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The Joint PVSS JCOP Framework: 14 - 18.6.2004 (5 days) EXCEL 2003 - niveau 2 : 17 & 18.6.2004 (2 jours) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 au 8.7.2004 (3 jours) Technical Training Monique Duval - Tel.74924 technical.training@cern.ch

  15. Understanding Socio Technical Modularity

    DEFF Research Database (Denmark)

    Thuesen, Christian Langhoff; Kudsk, Anders; Hvam, Lars

    2011-01-01

    Modularity has gained an increasing popularity as a central concept for exploring product structure, process structure, organization structure and supply chain structure. With the offset in system theory the predominant understanding of modularity however faces difficulties in explaining the social...... dimension of modularity like irrational behaviors, cultural differences, learning processes, social organization and institutional influences on modularity. The paper addresses this gab offering a reinterpretation of the modularity concept from a socio-technical perspective in general and Actor Network...... Theory in particular. By formulating modularity from an ANT perspective covering social, material and process aspects, the modularity of a socio-technical system can be understood as an entanglement of product, process, organizational and institutional modularity. The theoretical framework is illustrated...

  16. Independent technical review, handbook

    International Nuclear Information System (INIS)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project

  17. Independent technical review, handbook

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project.

  18. Technical approach document

    International Nuclear Information System (INIS)

    1989-12-01

    The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs

  19. Technical Leadership Development Program

    Science.gov (United States)

    2010-12-13

    the traditional tenets of leadership and management , systems thinking, understanding SOS issues, and thinking and acting holistically. Our research...international element 2.0 Enterprise Leadership and Management UNCLASSIFIED Contract Number: H98230-08-D-0171 DO 002. TO002, RT 004 Report No...mechanisms for leadership of the overall technical effort, for systems engineering, for requirements, management , and for systems integration. o Develop

  20. Technical issues for WIPP

    International Nuclear Information System (INIS)

    Hunter, T.O.

    1979-01-01

    Emplacement of wastes in the WIPP will include experiments on various waste types which will provide essential data on waste-rock interaction and repository response. These experiments will include evolution of the synergistic effects of both heat production, radiation, and actual waste forms. While these studies will provide essential data on the validity of waste isolation in bedded salt, they will be preceded by a broad-based experimental program which will resolve many of the current technical issues providing not only an assessment of the safety of performing such experiments but also the technical basis for assurance that the appropriate experiments are performed. Data and predictive modeling techniques, which are currently available, can bound the consequences associated with these technical issues. Predictions of the impact on public safety based on these analyses indicate that safe waste disposal in WIPP salt beds is achievable; however, a major use of WIPP will be to conduct realistic experiments with HLW forms to address some of the unresolved details of these waste/salt interactions

  1. Technical training - Places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924) HR Department Electronic Design Next Session Duration Language Availability Comprehensive VHDL for FPGA Design 08-Oct-12 to 12-Oct-12 5 days English 4 places Electrostatique / Protection ESD 28-Sep-12 to 28-Sep-12 3 hours French 25 places Impacts de la suppression du plomb (RoHS) en électronique 26-Oct-12 to 26-Oct-12 8 hours French 14 places Introduction to VHDL 10-Oct-12 to 11-Oct-12 2 days English 9 places LabVIEW Real Time and FPGA 13-Nov-12 to 16-Nov-12 5 days French 5 places LabVIEW for Experts 24-Sep-12 to 28-Sep-12 5 days English 6 places LabVIEW for beginners 15-Oct-12 to 17-...

  2. Technical Assistance Needs Assessments (TANAs)

    Science.gov (United States)

    The Technical Assistance Needs Assessment (TANA) is a process to identify whether a community requires additional support from EPA in order to understand technical information and have meaningful participation in the Superfund decision-making process.

  3. El Salvador - Formal Technical Education

    Data.gov (United States)

    Millennium Challenge Corporation — With a budget of nearly $20 million, the Formal Technical Education Sub-Activity was designed to strengthen technical and vocational educational institutions in the...

  4. Assessing Students' Technical Skill Attainment

    Science.gov (United States)

    Jorgensen, Haley

    2010-01-01

    The Wisconsin Technical College System (WTCS) is working to comply with the Carl D. Perkins Career and Technical Education Improvement Act of 2006 (Perkins) to ensure that its graduates have mastered the technical skills needed by business and industry. The legislation requires that each state identify and approve program assessment strategies…

  5. Towards technical interoperability in telemedicine.

    Energy Technology Data Exchange (ETDEWEB)

    Craft, Richard Layne, II

    2004-05-01

    For telemedicine to realize the vision of anywhere, anytime access to care, the question of how to create a fully interoperable technical infrastructure must be addressed. After briefly discussing how 'technical interoperability' compares with other types of interoperability being addressed in the telemedicine community today, this paper describes reasons for pursuing technical interoperability, presents a proposed framework for realizing technical interoperability, identifies key issues that will need to be addressed if technical interoperability is to be achieved, and suggests a course of action that the telemedicine community might follow to accomplish this goal.

  6. Methodology for technical risk assessment

    International Nuclear Information System (INIS)

    Waganer, L.M.; Zuckerman, D.S.

    1983-01-01

    A methodology has been developed for and applied to the assessment of the technical risks associated with an evolving technology. This methodology, originally developed for fusion by K. W. Billman and F. R. Scott at EPRI, has been applied to assess the technical risk of a fuel system for a fusion reactor. Technical risk is defined as the risk that a particular technology or component which is currently under development will not achieve a set of required technical specifications (i.e. probability of failure). The individual steps in the technical risk assessment are summarized. The first step in this methodology is to clearly and completely quantify the technical requirements for the particular system being examined. The next step is to identify and define subsystems and various options which appear capable of achieving the required technical performance. The subsystem options are then characterized regarding subsystem functions, interface requirements with the subsystems and systems, important components, developmental obstacles and technical limitations. Key technical subsystem performance parameters are identified which directly or indirectly relate to the system technical specifications. Past, existing and future technical performance data from subsystem experts are obtained by using a Bayesian Interrogation technique. The input data is solicited in the form of probability functions. Thus the output performance of the system is expressed as probability functions

  7. Argentina technical report

    International Nuclear Information System (INIS)

    2002-01-01

    At present, the Production Cyclotron Facility, installed at the Ezeiza Atomic Centre, is used for Tl-201 production; F-18 and I-123 production will be incorporated during this year. Concerning I-123 production, a system for irradiation of gaseous target has been developed in the frame of the IAEA Technical Assistance Project (ARG4085). The iodine production system delivers an ultra pure radioisotope via nuclear reactions: 124 Xe (p,2n) 123 Cs → 123 Xe → 123 I and 124 Xe (p,pn) 123 Xe → 123 I. This report describes the target and irradiation chamber design, the radiochemical purification process

  8. Technical Report 2000

    International Nuclear Information System (INIS)

    2001-01-01

    The technical memory 2000 of the Nuclear Regulatory Authority (NRA) of the Argentine Republic, compile the papers published in the subject on radiation protection and nuclear safety, safeguards and physical protection, and presented in congress or meetings of these specialities by personnel of the mentioned institution during 2000. In this edition the documents are presented on: Nuclear safety; Radiobiology; Occupational doses; Radiochemical; Environmental studies; Emergency plans; Radiation accidents; and International safeguards. Some of them are realized by agreements between the Nuclear Regulatory Authority of Argentina, universities and other national and international organizations

  9. HPCG Benchmark Technical Specification

    Energy Technology Data Exchange (ETDEWEB)

    Heroux, Michael Allen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dongarra, Jack [Univ. of Tennessee, Knoxville, TN (United States); Luszczek, Piotr [Univ. of Tennessee, Knoxville, TN (United States)

    2013-10-01

    The High Performance Conjugate Gradient (HPCG) benchmark [cite SNL, UTK reports] is a tool for ranking computer systems based on a simple additive Schwarz, symmetric Gauss-Seidel preconditioned conjugate gradient solver. HPCG is similar to the High Performance Linpack (HPL), or Top 500, benchmark [1] in its purpose, but HPCG is intended to better represent how today’s applications perform. In this paper we describe the technical details of HPCG: how it is designed and implemented, what code transformations are permitted and how to interpret and report results.

  10. Technical bid evaluation

    International Nuclear Information System (INIS)

    Bruchhausen, E. v.

    1975-01-01

    It is shown which kind of problems arise for the owners of the project and what is the recommendable method of approach. A detailed description of the necessary working team, information in delegation of work and tasks of procedure, criteria of valuation and classification method. Examples of schemes are shown which are the basis of the technical bid evaluation: tables 'data of system/component' and 'scope of supply'. The procedure of normalization of the bids and of specifying the owners supplies are explained. The content of the final report is described. (HP) [de

  11. RADTRAN 6 Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Weiner, Ruth F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neuhauser, Karen Sieglinde [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Heames, Terence John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); O' Donnell, Brandon M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dennis, Matthew L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-01-01

    This Technical Manual contains descriptions of the calculation models and mathematical and numerical methods used in the RADTRAN 6 computer code for transportation risk and consequence assessment. The RADTRAN 6 code combines user-supplied input data with values from an internal library of physical and radiological data to calculate the expected radiological consequences and risks associated with the transportation of radioactive material. Radiological consequences and risks are estimated with numerical models of exposure pathways, receptor populations, package behavior in accidents, and accident severity and probability.

  12. RADTRAN 6 technical manual.

    Energy Technology Data Exchange (ETDEWEB)

    Weiner, Ruth F.; Neuhauser, Karen Sieglinde; Heames, Terence John; O' Donnell, Brandon M.; Dennis, Matthew L.

    2014-01-01

    This Technical Manual contains descriptions of the calculation models and mathematical and numerical methods used in the RADTRAN 6 computer code for transportation risk and consequence assessment. The RADTRAN 6 code combines user-supplied input data with values from an internal library of physical and radiological data to calculate the expected radiological consequences and risks associated with the transportation of radioactive material. Radiological consequences and risks are estimated with numerical models of exposure pathways, receptor populations, package behavior in accidents, and accident severity and probability.

  13. Technics and ethics

    International Nuclear Information System (INIS)

    Budnick, D.; Gemmel, F.

    1981-01-01

    Questions about the sense of life and the responsibility of technology are ethical questions. Young people in our neighbourhood who, compared to some time ago, see, hear and read much more of the world, deal with them increasingly. However, the permanent stream of information does not at all facilitate orientation but prevents many people from gaining some clearness about their own point of view. In asking the questions: where are we today. How can we get on. How can we start. The relation between ethics and technics is discussed under various aspects. (orig./HSCH) [de

  14. Technical summaries of Scotian Shelf - significant and commercial discoveries

    International Nuclear Information System (INIS)

    Dickey, J.E.; Bigelow, S.F.; Edens, J.A.; Brown, D.E.; Smith, B.; Makrides, C.; Mader, R.

    1997-03-01

    An independent assessment of the recoverable hydrocarbon resource currently held under' Significant and Commercial Discovery' status offshore Nova Scotia was presented. A generalized description of the regulatory issues regarding the discovered resources within the Scotian Basin was included. Twenty discoveries have been declared significant and two have been declared commercial, pursuant to the Canada-Nova Scotia Offshore Petroleum Resources Accord Implementation Acts. Salient facts about each discovery were documented. The information included the wells drilled within the structure, significant flow tests, geological and geophysical attributes, structural cross-section and areal extent, petrophysical parameters, hydrocarbons in place and anticipated hydrocarbon recoverable resource. tabs., figs

  15. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) Introduction to the CERN EDMS : 9.3.2004 (1 day, free of charge) The EDMS MTF in Practice : 10.3.2004 (morning, free of charge) CLEAN-2002: Working in a Cleanroom : 10.3.2004 (afternoon, free of charge) The CERN EDMS for Engineers : 11.3.2004 (1 day, free of charge) LabVIEW hands-on (E):...

  16. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW base 1 : 25 - 27.2.2004(3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 26.2.2004 (morning) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) LabVIEW hands-on (E) : 16.3.2004 (afternoon) LabVIEW Basics 1 : 22 - 24.3.2004 ...

  17. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study for Microsoft applications :12.2.2004 (morning) Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) CLEAN-2002 ...

  18. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 26.2.2004 (morning) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Pa...

  19. Technical training: places available

    CERN Multimedia

    HR Department

    2007-01-01

    CERN Technical Training: Open Courses (April - June 2007) The following course sessions are currently scheduled in the framework of the CERN Technical Training Programme 2007:   AutoCAD 2006 - niveau 1 (course in French): 25.4.- 26.4.2007 & 2.5. - 3.5.2007 (4 days in 2 modules, 5 places available) AutoCAD 2006 - niveau 1 (course in French): 27.6.- 28.6.2007 & 3.7. - 4.7.2007 (4 days in 2 modules, 5 places available) AutoCAD Mechanical 2006 (course in French) 21.6.-22.6.2007 (2 days, 8 places available) * NEW COURSE* Automate de securite S7 (course in French) 14.5.-16.5.2007 (3 days, 4 places available) * NEW COURSE* Automate de securite S7 (course in French): 9.5.-11.5.2007 (3 days, 4 places available) JCOP - Joint PVSS-JCOP Frameswork (course in English): 21.5.-25.5.2007 (5 days, 12 places available) JCOP - Finite State Machines in the JCOP Frameswork (course in English): 12.6.-14.6.2007 (3 days, 12 places available) LabVIEW Basics 1 (in English): 2.-4.5.2007 (3 days, 7 places ...

  20. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Wednesday 6 March TECHNICAL TRAINING SEMINAR from 9:30 to 16:45 - IT Amphitheatre - bldg. 31.3.004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars...

  1. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) Introduction to the CERN EDMS : 9.3.2004 (1 day, free of charge) The EDMS MTF in Practice : 10.3.2004 (morning, free of charge) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon, free of charge) The CERN EDMS for Engineers : 11.3.2004 (1 day, free of charge) LabVIEW...

  2. Technical Training: Places available**

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1 : 9 & 10.1.2004 (2 days) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 ( 6 X 4-hour sessions) LabVIEW hands-on (E) 16.3...

  3. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Project Planning with MS-Project :6 & 13.5.2004 (2 days) Word 2003 - niveau 1 : 10 & 11.5.2004 (2 jours) Oracle 9i : SQL : 17 - 19.5.2004 (3 days) Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) EXCEL 2003 - niveau 1: 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1 : 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL : 2 - 4.6.2...

  4. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 28.6 - 1.7.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo... Work with long documents : 6.7.2005 (afternoon) ACCES...

  5. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework: 8 - 12.8.2005 (5 days) FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1 : 5 - 7.9.2005 (3 days, dates to be confirmed) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) LabVIEW Application Development (Intermediate I): 5 - 7.12.2005 (3 days) LabVIEW Advanced Programming (Intermediate 2): 8 - 9.12.2005 (2 days) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

  6. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo (4 mornings) EXCEL 2003 (Short Course I) - HowTo... Work ...

  7. Technical Training: Places Available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval - Tel.74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Oracle 9i: SQL: 17 - 19.5.2004 (3 days) Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) EXCEL 2003 - niveau 1 : 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1: 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL: 2 - 4.6.2004 (3 days) CST Microwave Studio: 3 & 4.6.2004 (2 days) Oracle 9i : New f...

  8. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval - Tel.74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) VisualEliteHDL : 25 & 26.5.2004 (2 days) EXCEL 2003 - niveau 1 : 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1: 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL: 2 - 4.6.2004 (3 days) CST Microwave Studio: 3 & 4.6.2004 (2 days) Oracle 9...

  9. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study or follow-up for Microsoft applications : 1.4.2004 (morning) FrontPage XP - niveau 1 : 5 & 6.4.2004 (2 jours) AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 day...

  10. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) The Joint PVSS JCOP Framework : 26 - 30.4.2004 (5 days) Computational Electromagnetics with the ELEKTRA Module of OPERA-3D : 27 & 28.4.2004 (2 days) Hands-on Introduction to Python Programming : 3 - 5.5.2004 (3 days) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Project Pla...

  11. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Computational Electromagnetics with the ELEKTRA Module of OPERA-3D : 27 & 28.4.2004 (2 days) Hands-on Introduction to Python Programming : 3 - 5.5.2004 (3 days) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Project Planning with MS-Project : 6 & 13.5.2004 (2 days) Word 2003 - niveau 1 : 10 & 11.5.2004 (2 jours) Oracle 9i : SQL : 10 - 12.5.2004 (3...

  12. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 days) LabVIEW Hands-on : 20.4.2004 (half-day, p.m.) FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) The Joint PVSS JCOP Framework : 26 -...

  13. TECHNICAL TRAINING: Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Hands-on Introduction to Python Programming : 12 - 14.11.03(3 days) ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) C++ for Particle Physicists : 17 - 21.11.03 (6 X 3-hour lectures) Programmation automate Schneider TSX Premium - niveau 2 : 18 - 21.11.03 (4 jours) Project Planning with MS-Project  (free of charg...

  14. TECHNICAL TRAINING: Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval Tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The EDMS-MTF in practice (free of charge) : 28 -  30.10.03 (6 half-day sessions) AutoCAD 2002 – Level 1 : 3, 4, 12, 13.11.03 (4 days) LabVIEW TestStand ver. 3 : 4 & 5.11.03 (2 days) Introduction to PSpice : 4.11.03 p.m. (half-day) Hands-on Introduction to Python Programming : 12 – 14.11.03 (3 days) ACCESS ...

  15. Technical Writing: Past, Present and Future

    Science.gov (United States)

    Mathes, J. C. (Compiler); Pinelli, T. E. (Compiler)

    1981-01-01

    The training of technical writers and the objectives of such education are discussed. Special emphasis was placed on the communication between technical personnel and non-technical personnel. The liabilities that affect technical writers were also discussed.

  16. Technical Support Essentials Advice to Succeed in Technical Support

    CERN Document Server

    Sanchez, Andrew

    2010-01-01

    Technical Support Essentials is a book about the many facets of technical support. It attempts to provide a wide array of topics to serve as points of improvement, discussion, or simply topics that you might want to learn. The topics range from good work habits to the way technical supportgroups establish their own style of work. This book applies theories, models, and concepts synthesized from existing research in other fields-such as management, economics, leadership, and psychology-and connects them to technical support. The goal is to build on the work of others and allow their success to

  17. Technical standards in the law of technical safety

    International Nuclear Information System (INIS)

    Marburger, P.

    1985-01-01

    Technical standards are of great importance for the closer definition of inexact terms of law, for instance ''generally accepted technical rules'', ''state of the art'', ''state of science and technology'' or similar normative terms, in the law of technical safety. The paper discusses with whom the authority for regulating this sector of law rests, deals with the different ways of how technical standards are used by the law (''anticipated expert opinion'', reference to such standards in law and administration) and points out demands on the procedure of standardization. (orig.) [de

  18. Chapter 2. Assessment of undiscovered conventional oil and gas resources--Upper Jurassic-Lower Cretaceous Cotton Valley group, Jurassic Smackover interior salt basins total petroleum system, in the East Texas basin and Louisiana-Mississippi salt basins provinces.

    Science.gov (United States)

    Dyman, T.S.; Condon, S.M.

    2006-01-01

    The Jurassic Smackover Interior Salt Basins Total Petroleum System is defined for this assessment to include (1) Upper Jurassic Smackover Formation carbonates and calcareous shales and (2) Upper Jurassic and Lower Cretaceous Cotton Valley Group organic-rich shales. The Jurassic Smackover Interior Salt Basins Total Petroleum System includes four conventional Cotton Valley assessment units: Cotton Valley Blanket Sandstone Gas (AU 50490201), Cotton Valley Massive Sandstone Gas (AU 50490202), Cotton Valley Updip Oil and Gas (AU 50490203), and Cotton Valley Hypothetical Updip Oil (AU 50490204). Together, these four assessment units are estimated to contain a mean undiscovered conventional resource of 29.81 million barrels of oil, 605.03 billion cubic feet of gas, and 19.00 million barrels of natural gas liquids. The Cotton Valley Group represents the first major influx of clastic sediment into the ancestral Gulf of Mexico. Major depocenters were located in south-central Mississippi, along the Louisiana-Mississippi border, and in northeast Texas. Reservoir properties and production characteristics were used to identify two Cotton Valley Group sandstone trends across northern Louisiana and east Texas: a high-permeability blanket-sandstone trend and a downdip, low-permeability massive-sandstone trend. Pressure gradients throughout most of both trends are normal, which is characteristic of conventional rather than continuous basin-center gas accumulations. Indications that accumulations in this trend are conventional rather than continuous include (1) gas-water contacts in at least seven fields across the blanket-sandstone trend, (2) relatively high reservoir permeabilities, and (3) high gas-production rates without fracture stimulation. Permeability is sufficiently low in the massive-sandstone trend that gas-water transition zones are vertically extensive and gas-water contacts are poorly defined. The interpreted presence of gas-water contacts within the Cotton Valley

  19. Estimating USAF Aircraft Recoverable Spares Investment.

    Science.gov (United States)

    1980-08-01

    ITEMS Multiple Regression Equation RCCAVI - 178.44118(AC)’ 39843(AVFAC) ൰ 62 2 e 27003 (IB ) + 2.4257(1R e 1.0 9 99 (IF/A) + 1.1 8 11 (1C) + 1.100...79- I M In *~Nt M h IOOO N1 0 , C 0 0 30~ It- N t- INN0010 - t 10 N M mt00 01 0,󈧈 01c 0 0 0000’ ast-00 10%I I t~-.. ~ ISO ~ tO It- . lO tfls4 I1 MD...0K 0 4 #40 D Jr *0 2z < I 0 -I - . - - I 0 I IN , 0 H0 PA C, :,C n BCY -4 0 -a C I z nL Z4 w11 00 WI Z4 4 ) L. zWI W -98- w Iq IN N05 IsO I 5I 00 0 1

  20. Gas Environment Recoverable Detection (GERD) HMI

    CERN Document Server

    Sillat, Mari Liis

    2016-01-01

    Report on the work done during the summer student project. The goal was to produce HMI panels for the GERD smoke detection system. The required platform was WinCC OA and the running sensor data needed to be displayed, pump controls were needed and an alarm was required to be set for the smoke sensors upper limit range.

  1. Distributed and recoverable digital control system

    Science.gov (United States)

    Stange, Kent (Inventor); Hess, Richard (Inventor); Kelley, Gerald B (Inventor); Rogers, Randy (Inventor)

    2010-01-01

    A real-time multi-tasking digital control system with rapid recovery capability is disclosed. The control system includes a plurality of computing units comprising a plurality of redundant processing units, with each of the processing units configured to generate one or more redundant control commands. One or more internal monitors are employed for detecting data errors in the control commands. One or more recovery triggers are provided for initiating rapid recovery of a processing unit if data errors are detected. The control system also includes a plurality of actuator control units each in operative communication with the computing units. The actuator control units are configured to initiate a rapid recovery if data errors are detected in one or more of the processing units. A plurality of smart actuators communicates with the actuator control units, and a plurality of redundant sensors communicates with the computing units.

  2. Water Impact Prediction Tool for Recoverable Rockets

    Science.gov (United States)

    Rooker, William; Glaese, John; Clayton, Joe

    2011-01-01

    Reusing components from a rocket launch can be cost saving. NASA's space shuttle system has reusable components that return to the Earth and impact the ocean. A primary example is the Space Shuttle Solid Rocket Booster (SRB) that descends on parachutes to the Earth after separation and impacts the ocean. Water impact generates significant structural loads that can damage the booster, so it is important to study this event in detail in the design of the recovery system. Some recent examples of damage due to water impact include the Ares I-X First Stage deformation as seen in Figure 1 and the loss of the SpaceX Falcon 9 First Stage.To ensure that a component can be recovered or that the design of the recovery system is adequate, an adequate set of structural loads is necessary for use in failure assessments. However, this task is difficult since there are many conditions that affect how a component impacts the water and the resulting structural loading that a component sees. These conditions include the angle of impact with respect to the water, the horizontal and vertical velocities, the rotation rate, the wave height and speed, and many others. There have been attempts to simulate water impact. One approach is to analyze water impact using explicit finite element techniques such as those employed by the LS-Dyna tool [1]. Though very detailed, this approach is time consuming and would not be suitable for running Monte Carlo or optimization analyses. The purpose of this paper is to describe a multi-body simulation tool that runs quickly and that captures the environments a component might see. The simulation incorporates the air and water interaction with the component, the component dynamics (i.e. modes and mode shapes), any applicable parachutes and lines, the interaction of winds and gusts, and the wave height and speed. It is capable of quickly conducting Monte Carlo studies to better capture the environments and genetic algorithm optimizations to reproduce a flight.

  3. Technical specification use and application

    International Nuclear Information System (INIS)

    Williamson, D.; Hoffman, D.R.

    1991-01-01

    Since early 1988 intensive efforts have been under way to produce a new and improved Standard Technical Specification. The program involves a coordinated effort between utility personnel representing each of the four nuclear steam supply system (NSSS) product lines, the NSSS vendors, and the US Nuclear Regulatory Commission (NRC). This intensive work period is actually the culmination of a decade of rhetoric about shortcomings of the existing technical specifications. Work on the improved technical specifications provided a unique forum for intense philosophical discussions between the users and enforcers of technical specifications, the outcome of which could have an impact on all licensees. Some of the more intriguing difficulties in the use and application of existing technical specifications, as well as discussions of the resolutions being applied in the improved technical specifications and the dilemmas remaining to be resolved are discussed in the paper

  4. Technical applications of aerogels

    International Nuclear Information System (INIS)

    Hrubesh, L.W.

    1997-01-01

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels

  5. Technical Report - FINAL

    Energy Technology Data Exchange (ETDEWEB)

    Barbara Luke, Director, UNLV Engineering Geophysics Laboratory

    2007-04-25

    Improve understanding of the earthquake hazard in the Las Vegas Valley and to assess the state of preparedness of the area's population and structures for the next big earthquake. 1. Enhance the seismic monitoring network in the Las Vegas Valley 2. Improve understanding of deep basin structure through active-source seismic refraction and reflection testing 3. Improve understanding of dynamic response of shallow sediments through seismic testing and correlations with lithology 4. Develop credible earthquake scenarios by laboratory and field studies, literature review and analyses 5. Refine ground motion expectations around the Las Vegas Valley through simulations 6. Assess current building standards in light of improved understanding of hazards 7. Perform risk assessment for structures and infrastructures, with emphasis on lifelines and critical structures 8. Encourage and facilitate broad and open technical interchange regarding earthquake safety in southern Nevada and efforts to inform citizens of earthquake hazards and mitigation opportunities

  6. Socio-Technical Structure

    DEFF Research Database (Denmark)

    Rose, Jeremy; Lindgren, Rikard; Henfridsson, Ole

    2004-01-01

    a reference discipline in its own right (in other words a theory exporter), this paper offers an example of integrative theory development. Instead of adapting a theory from another discipline or building a theory from empirical data, we examine the structure concept in some of its various theoretical......When it comes to investigating the relationship between the social and the technical, IS has been a net importer of theories. These theories often carry differing interpretations of central concepts, which then become both confusing and difficult to integrate. In response to calls for IS to become...... adaptations in IS and try to integrate them to produce theory that focuses on IS concerns whilst resolving some of the major areas of contention. Both social and technological versions of structure are investigated through three theoretical IS perspectives drawn from different reference disciplines. The first...

  7. LLNL 1981: technical horizons

    International Nuclear Information System (INIS)

    1981-07-01

    Research programs at LLNL for 1981 are described in broad terms. In his annual State of the Laboratory address, Director Roger Batzel projected a $481 million operating budget for fiscal year 1982, up nearly 13% from last year. In projects for the Department of Energy and the Department of Defense, the Laboratory applies its technical facilities and capabilities to nuclear weapons design and development and other areas of defense research that include inertial confinement fusion, nonnuclear ordnances, and particle-beam technology. LLNL is also applying its unique experience and capabilities to a variety of projects that will help the nation meet its energy needs in an environmentally acceptable manner. A sampling of recent achievements by LLNL support organizations indicates their diversity

  8. Technical Training Seminar

    CERN Multimedia

    2003-01-01

    Wednesday 19 November From 9:30 to 17:30 - IT Amphitheatre bldg.31 3-004 2003 Data Transmission Design Seminar - TEXAS INSTRUMENTS The one-day 2003 Data Transmission Design Seminar is part of a series of technical seminars produced by Texas Instruments. This series of seminars will introduce system solutions based on different standards according to their respective requirements. It will include topics containing a blend of basic principles and hands-on application examples, along with layout-guidelines. • Basics and Practical Examples of Data-Transmission • Low Voltage Differential Signaling (LVDS) • Connectivity and PC-based Links • Industrial Interfaces • Parallel Bus Systems and Clock-Distribution-Circuits (CDC) This Seminar will be of interest to hardware designers and system engineers dealing with the realization of system- or board-level interfaces based on various transmission standards. Language: English Free seminar, no registration Organiser: John ...

  9. Technical Math For Dummies

    CERN Document Server

    Schoenborn, Barry

    2010-01-01

    Technical Math For Dummies is your one-stop, hands-on guide to acing the math courses you’ll encounter as you work toward getting your degree, certifacation, or�license in the skilled trades. You’ll get easy-to-follow, plain-English guidance on mathematical formulas and methods that professionals use every day in the automotive, health, construction, licensed trades, maintenance, and other trades. You’ll learn how to apply concepts of algebra, geometry, and trigonometry and their formulas related to occupational areas of study. Plus, you’ll find out how to perform basic arithmetic

  10. Technical Training: ELEC-2005

    CERN Multimedia

    Davide Vitè

    2005-01-01

    ELEC-2005 - Electronics in High Energy Physics: Autumn Term (November-December 2005) ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the ELEC-2002 course series. This new, comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms. The Winter (Introduction to electronics in HEP), Spring (Integrated circuits and VLSI technology for physics), and Summer (System electronics for physics: Issues) Terms already took place. The Autumn Term: Electronics applications in HEP experiments (November-December, 10 lectures) is now open for online registration, and will start on November 8th with the...

  11. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Eggeman, Tim [ZeaChem Inc., Lakewood, CO (United States); O' Neill, Brian [ZeaChem Inc., Lakewood, CO (United States)

    2016-08-17

    ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was already in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive inhibitors

  12. Final technical report

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    gas jet chamber and laser beam path from the final focusing mirror. The project consists of three phases: Phase 1: Fundamental studies of cutting front mechanisms, beam propagation, nozzle design and chemical reactions in the cut kerf with special emphasize on high laser powers and thick sections...... cutting nozzle which can be adjusted independently to the laser beam has been developed. The position of the focus relative the workpiece can be adjusted to cutting applications with relatively large processing windows, i.e. both mild and stainless steels, and of a broad thickness range. A build-in auto......This project entails research with the goal to extend laser cutting of steel based metals to thickness above 20 mm and laser powers in the 10 kW range, with adequate accuracy and economically viable cutting speeds. The technical approach is to develop mirror based cutting heads with truly coaxial...

  13. TECHNICAL TRAINING PROGRAMME

    CERN Multimedia

    Davide Vitè

    2002-01-01

    CLEAN-2002: Working in a Cleanroom A new, free of charge, half-day seminar is offered in the context of Technical Training for the LHC, for personnel working or managing activities in a cleanroom (for example physicists, engineers and technicians working at or visiting the laboratory). CLEAN-2002 is aimed at raising awareness about good working practices in a cleanroom, and at providing practical examples, analysis tools, and documentation. Specific problems put forward beforehand by attendees will also be addressed, if possible. More information and registration is available HERE The next session, in English, will be on 24.4 (afternoon). Other sessions, in French and English, will be offered following demand. Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch

  14. Technical knowledge creation

    DEFF Research Database (Denmark)

    Søberg, Peder Veng

    2017-01-01

    Purpose - The purpose of the paper is to amend shortcomings of existing theory concerning organizational learning and knowledge management. Design/methodology/approach – The paper reviews and refines existing theory. Findings - Findings from cognitive neuroscience suggest that technical knowledge...... domains essential for product development are largely nonlinguistic. Operations management/strategy tools enable the use of tacit knowledge in its tacit form and discourage premature standardization. Similarly, language use introduces standardization, which if introduced prematurely, causes incrementalism...... in line with findings from product development research. However, frameworks on organizational learning and knowledge management focus on language development and neglect use of tacit knowledge and the benefits involved with allowing elements of new product ideas to mature in a tacit form. Originality...

  15. Technical Due Diligence

    DEFF Research Database (Denmark)

    Jensen, Per Anker; Varano, Mattia

    2011-01-01

    carried out for buyers or sellers involved in real estate transactions. It can also be part of mergers including real estate and other assets or part of facilities management outsourcing. This paper is based on a case study and an interview survey of companies involved in TDD consulting in Denmark......Technical Due Diligence (TDD) as an evaluation of the performance of constructed facilities has become an important new field of practice for consultants. Before the financial crisis started in autumn 2008 it represented the fastest growing activity in some consulting companies. TDD is mostly...... and Italy during 2009. The research identifies the current practice and compares it with the recommended practice in international guidelines. The current practice is very diverse and could in many cases be improved by a more structured approach and stricter adherence to international guidelines. However...

  16. ITER technical basis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties.

  17. ITER technical basis

    International Nuclear Information System (INIS)

    2002-01-01

    Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties

  18. Assessment of technical risks

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, T A [Bundesanstalt fuer Materialpruefung, Berlin (Germany, F.R.)

    1978-01-01

    The safety of technical systems is so difficult to assess because the concept 'risk' contains technical-scientific factors as well as components of individual and social psychology. Immediate or short-term hazards of human life as i.e. caused by the operation of industrial plants and mediate and thus long-term hazards have to be distinguished. Characteristic for the second hazard groups is the great time-lag before the effect takes place. Thus a causal relationship can be recognized only late and not definitely. Even when the causes have been obviated the effects still show. The development of a systems-analytical model as a basis of decisive processes for the introduction of highly endangered large-scale technologies seems particularly difficult. A starting point for the quantification of the risk can still be seen in the product of the probability of realization and the extent of the damage. Public opinion, however, does not base its evaluations on an objective concept of risk but tends to have an attitude of aversion against great and disastrous accidents. On the other hand, plenty of slight accidents are accepted much more easily, even when the amount of deadly victims from accidents reaches dimensions beyond those of the rare large-scale accidents. Here, mostly the damage possible but not the probability of its occurence is seen, let alone the general use of the new technology. The value of the mathematical models for estimating risks is mainly due to the fact that they are able to clear up decisions.

  19. Mechanical engineering department technical review

    International Nuclear Information System (INIS)

    Carr, R.B.; Denney, R.M.

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work

  20. Mechanical Engineering Department. Technical review

    Energy Technology Data Exchange (ETDEWEB)

    Simecka, W.B.; Condouris, R.A.; Talaber, C. (eds.)

    1980-01-01

    The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work.

  1. Mechanical Engineering Department technical abstracts

    International Nuclear Information System (INIS)

    Denney, R.M.

    1982-01-01

    The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts

  2. Mechanical Engineering Department Technical Review

    International Nuclear Information System (INIS)

    Carr, R.B.; Denney, R.M.

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication

  3. TECHNICAL CULTURE AND HUMAN AXJOSPHERE

    OpenAIRE

    ­Krystyna Chałas

    2014-01-01

    Technical culture is the value of each historical period. It is the subject of the ongoing development. While it is a value which is associated with different categories of values, mainly material, cognitive, social. Between culture and these three categories of values ​ there is a cognitive effect. Technical culture determines the quality of human axjosphere. The aim of this study is to show the relationships and dependencies between technical culture and the structures in which a person liv...

  4. The story of technical cooperation

    International Nuclear Information System (INIS)

    Park, Yang Taek

    1989-09-01

    This book gives descriptions of technical cooperation, which is about why does technology transfer?, process of technology transfer with model, decisive cause and cooperation of technology transfer, cost and effect of technology transfer, historical experience of technology transfer, cases of technology transfer by field such as rubber tire, medicine and computer industry and automobile industry, technology transfer process and present condition of technical cooperation, and strategy for rising of technical cooperation : selection of technology for object of cooperation and development of human resources.

  5. Mechanical Engineering Department. Technical review

    International Nuclear Information System (INIS)

    Simecka, W.B.; Condouris, R.A.; Talaber, C.

    1980-01-01

    The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work

  6. ERLN Technical Support for Labs

    Science.gov (United States)

    The Environmental Response Laboratory Network provides policies and guidance on lab and data requirements, Standardized Analytical Methods, and technical support for water and radiological sampling and analysis

  7. The logic of Technical Standardisation

    DEFF Research Database (Denmark)

    Nedergaard, Peter

    In this paper technical standardisation is understood and explained in a model where economic analysis is coupled with an analysis of the political system as proposed in rational choice theory. The aim is to answer both the question why various countries (e.g. the United States versus European...... countries) let either the market or public intervention determine the mode of technical standardisation and the possible implications of these two ways of organizing technical standardisation from an economic and a political point of view. Based upon the analysis of the paper a couple of general policy...... recommendations are made concerning the mode of technical standardisation....

  8. Predictors of employer satisfaction: technical and non-technical skills.

    Science.gov (United States)

    Danielson, Jared A; Wu, Tsui-Feng; Fales-Williams, Amanda J; Kirk, Ryan A; Preast, Vanessa A

    2012-01-01

    Employers of 2007-2009 graduates from Iowa State University College of Veterinary Medicine were asked to respond to a survey regarding their overall satisfaction with their new employees as well as their new employees' preparation in several technical and non-technical skill areas. Seventy-five responses contained complete data and were used in the analysis. Four technical skill areas (data collection, data interpretation, planning, and taking action) and five non-technical skill areas (interpersonal skills, ability to deal with legal issues, business skills, making referrals, and problem solving) were identified. All of the skill area subscales listed above had appropriate reliability (Cronbach's alpha>0.70) and were positively and significantly correlated with overall employer satisfaction. Results of two simultaneous regression analyses indicated that of the four technical skill areas, taking action is the most salient predictor of employer satisfaction. Of the five non-technical skill areas, interpersonal skills, business skills, making referrals, and problem solving were the most important skills in predicting employer satisfaction. Hierarchical regression analysis revealed that all technical skills explained 25% of the variation in employer satisfaction; non-technical skills explained an additional 42% of the variation in employer satisfaction.

  9. Aligning Career and Technical Education

    Science.gov (United States)

    Workman, Ed; Stubbs, Joyce

    2011-01-01

    The issues and concerns facing Kentucky Career and Technical Teacher Education (KY CTTE), university teacher educators and state department Career and Technical Education (CTE) leaders in providing and preparing the best CTE teachers possible are not unique to Kentucky. In an effort to better understand these issues and concerns a team of state…

  10. The Digital technical documentation handbook

    CERN Document Server

    Schultz, Susan I; Kavanagh, Frank X; Morse, Marjorie J

    1993-01-01

    The Digital Technical Documentation Handbook describes the process of developing and producing technical user information at Digital Equipment Corporation. * Discusses techniques for making user information _more effective * Covers the draft and reviewprocess, the production and distribution of printed and electronic media, archiving, indexing, testing for usability, and many other topics * Provides quality assurance checklists, contains a glossary and a bibliography of resources for technicalcommunicators

  11. Technical Education and Economic Growth

    Indian Academy of Sciences (India)

    First page Back Continue Last page Graphics. Technical Education and Economic Growth. Technical Education and Economic Growth. Review of the Present Status. Expanding no.s and impairment of quality; Faculty shortage; Grim situation at Masters and PhD levels; Regional imbalance; Absence of International flavour ...

  12. International Scientific and Technical Organisations

    International Nuclear Information System (INIS)

    Nunez-Lagos Rogla, R.

    2003-01-01

    The nuclear scientific and technical world is well aware of the EURATOM and IAEA activities but usually other international scientific and technical organisations relevant for their ordinary work are unknown. In this article three international organisations are described briefly, the International Union of Pure and Applied Physics (IUPAP). International Union of Pure and Applied chemistry (IUPAC) and the international council of Science (ICSU). (Author)

  13. PIAAC Technical Standards and Guidelines

    Science.gov (United States)

    OECD Publishing, 2014

    2014-01-01

    The Programme for International Assessment of Adult Competencies (PIAAC) will establish technical standards and guidelines to ensure that the survey design and implementation processes of PIAAC yield high-quality and internationally comparable data. This document provides a revised version of the technical standards and guidelines originally…

  14. EDI and the Technical Communicator.

    Science.gov (United States)

    Eiler, Mary Ann

    1994-01-01

    Assesses the role of technical communicators in electronic data interchange (EDI). Argues that, as experts in information design, human factors, instructional theory, and professional writing, technical communicators should be advocates of standard documentation protocols and should rethink the traditional concepts of "document" to…

  15. Technical training - Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 16.5.2006 (May-November course sessions) Technical Training: Places available The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language ACROBAT 7.0 : Utilisation de fichiers PDF 8 8.05.06 F WORD 2003 - niveau 2 : ECDL 16 22-23.05.06 23-24.05.06 F Comprehensive VHDL for FPGA Design 40 29.05-2.06.06 E C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls 32 30.05-2.06.06 E ACROBAT 7.0 : Utilisation de fichiers PDF 24 7-9.06.06 E AutoCAD Mechanical 2006 16 13-14.06.06 F CERN EDMS for Local Administrators 16 13-14.06.06 E LabVIEW Base 2 32 27.06-5.07.06 F C++ Programming Part 3 - Templates and the STL (Standard Template Library) 16 27-28.06.06 E C++ Programming Part 4 - Exceptions 8 29.06.06 E FrontPage 2003 - niveau 1 16 29-...

  16. GEM Technical Design Report

    International Nuclear Information System (INIS)

    1993-01-01

    The GEM collaboration was formed in June 1991 to develop a major detector for the SSC. The primary physics objectives of GEM are those central to the motivation for the SSC, to study high p T physics - exemplified by the search for Higgs bosons - and to search for new physics beyond the standard model. The authors present in this Technical Design Report (TDR) a detector with broad capabilities for the discovery and subsequent study of electroweak symmetry breaking, the origin of mass and flavor, and other physics requiring precise measurements of gammas, electrons, and muons - hence the name, GEM. In addition, as a design goal, they have taken care to provide the robustness needed to do the physics that requires high luminosity. Finally, good coverage and hermeticity allow the detection of missing transverse energy, E T . The GEM design emphasizes clean identification and high resolution measurement of the primary physics signatures for high p T physics. The approach is to make precise energy measurements that maximize the sensitivity to rare narrow resonances, to detect the elementary interaction products (quarks, leptons, and photons), and to build in the features required to reduce backgrounds

  17. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Wednesday 6 March from 9:30 to 16:45 - IT Auditorium - bldg. 31 3-004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars pages here or contact the organiser.

  18. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide VITÈ

    2002-01-01

    Wednesday 6 March   from 9:30 to 16:45 - IT Auditorium - bldg. 31 3-004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars pages here or con...

  19. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.09.2004 (4 jours) Introduction to the CERN EDMS : 22.6.2004 (1 day) The CERN EDMS for local administrators : 23 & 24.6.2004 (2 days) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 - 8.7.2004 (3 jours) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING...

  20. GEM Technical Design Report

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-31

    The GEM collaboration was formed in June 1991 to develop a major detector for the SSC. The primary physics objectives of GEM are those central to the motivation for the SSC, to study high p{sub T} physics - exemplified by the search for Higgs bosons - and to search for new physics beyond the standard model. The authors present in this Technical Design Report (TDR) a detector with broad capabilities for the discovery and subsequent study of electroweak symmetry breaking, the origin of mass and flavor, and other physics requiring precise measurements of gammas, electrons, and muons - hence the name, GEM. In addition, as a design goal, they have taken care to provide the robustness needed to do the physics that requires high luminosity. Finally, good coverage and hermeticity allow the detection of missing transverse energy, E{sub T}. The GEM design emphasizes clean identification and high resolution measurement of the primary physics signatures for high p{sub T} physics. The approach is to make precise energy measurements that maximize the sensitivity to rare narrow resonances, to detect the elementary interaction products (quarks, leptons, and photons), and to build in the features required to reduce backgrounds.

  1. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Programmation STEP7 niveau 1 : 14-17.9.2004 (4 jours) ANSYS : Thermal Analysis : 22 - 24.9.2004 (3 days) LabVIEW Migration 6 à 7 : 23.9.2004 (one day) ANSYS : Advanced Topics : 27.9 - 1.10.2004 (5 days) Word 2003 - niveau 2 : 27 & 28.9.2004 (2 jours) LabVIEW - Basics 1 : 27 - 29.9.2004 (3 days) MAGNE-04 : Magnétisme pour l'électrotechnique : 28 - 30.9.2004 (3 jours) LabVIEW - Basics 2 : 30.9 & 1.10.2004 (2 days) Introduction à Windows XP au CERN : 4.10.2004 (matin) FrontPage 2003 - niveau 1 : 7 & 8.10.04 (2 jours) Outlook (short course I) : E-mail : 22.10.2004 (2 hours, morning) Outlook (short course II) : Calendar, Tasks and Notes: 22.10.2004 (2 hours, afternoon) Introduction à ANSYS : 23 - 26.11.2004 (4 jours) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924...

  2. Waste Management Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, J.S. [ed.

    1967-08-31

    This Manual has been prepared to provide a documented compendium of the technical bases and general physical features of Isochem Incorporated`s Waste Management Program. The manual is intended to be used as a means of training and as a reference handbook for use by personnel responsible for executing the Waste Management Program. The material in this manual was assembled by members of Isochem`s Chemical Processing Division, Battelle Northwest Laboratory, and Hanford Engineering Services between September 1965 and March 1967. The manual is divided into the following parts: Introduction, contains a summary of the overall Waste Management Program. It is written to provide the reader with a synoptic view and as an aid in understanding the subsequent parts; Feed Material, contains detailed discussion of the type and sources of feed material used in the Waste Management Program, including a chapter on nuclear reactions and the formation of fission products; Waste Fractionization Plant Processing, contains detailed discussions of the processes used in the Waste Fractionization Plant with supporting data and documentation of the technology employed; Waste Fractionization Plant Product and Waste Effluent Handling, contains detailed discussions of the methods of handling the product and waste material generated by the Waste Fractionization Plant; Plant and Equipment, describes the layout of the Waste Management facilities, arrangement of equipment, and individual equipment pieces; Process Control, describes the instruments and analytical methods used for process control; and Safety describes process hazards and the methods used to safeguard against them.

  3. IAEA safeguards technical manual

    International Nuclear Information System (INIS)

    1982-03-01

    Part F of the Safeguards Technical Manual is being issued in three volumes. Volume 1 was published in 1977 and revised slightly in 1979. Volume 1 discusses basic probability concepts, statistical inference, models and measurement errors, estimation of measurement variances, and calibration. These topics of general interest in a number of application areas, are presented with examples drawn from nuclear materials safeguards. The final two chapters in Volume 1 deal with problem areas unique to safeguards: calculating the variance of MUF and of D respectively. Volume 2 continues where Volume 1 left off with a presentation of topics of specific interest to Agency safeguards. These topics include inspection planning from a design and effectiveness evaluation viewpoint, on-facility site inspection activities, variables data analysis as applied to inspection data, preparation of inspection reports with respect to statistical aspects of the inspection, and the distribution of inspection samples to more than one analytical laboratory. Volume 3 covers generally the same material as Volumes 1 and 2 but with much greater unity and cohesiveness. Further, the cook-book style of the previous two volumes has been replaced by one that makes use of equations and formulas as opposed to computational steps, and that also provides the bases for the statistical procedures discussed. Hopefully, this will help minimize the frequency of misapplications of the techniques

  4. Bulletin Survey: Technical clarifications

    CERN Multimedia

    2002-01-01

    In the latest of our articles on the results of the Bulletin survey, we respond to some of your technical comments on the Electronic Bulletin. Many thanks to the more than 500 of you who completed the questionnaire. The full statistics will be published next week. 'It takes too long to download the pages' Yes, it's true that the Electronic Bulletin's download time isn't perfect but it will improve when the Bulletin migrates to another, faster database. 'I find it very difficult to locate all the articles' Some people experience difficulty negotiating their way through the Bulletin once they have entered a specific section. The blue column on the left contains an 'In this issue' link taking you to the other sections. What's more, the whole of the paper Bulletin is available in the electronic version. As the latter is relatively new, however, it will take a bit of time to get used to browsing through it. Many of you say that it's still too early to form an opinion. 'Pull-down menus would be good, so that yo...

  5. Technical Training Seminar

    CERN Multimedia

    2003-01-01

    Thursday 4 September From 14:00 to 17:00 - Training Centre Auditorium bldg. 593, room 11 The Summit Design VisualElite 4.0 Release Jean Marie St Paul / SUMMIT DESIGN, Europe, Technical Manager Michel Delcroix / SUMMIT DESIGN, Southern Europe, Sales F-95015 CERGY PONTOISE, France Summit Design is an important EDA digital hardware design tool supplier, and the industry leader in the emerging Electronic System Level design domain. Its VisualElite program has been used at CERN for several years. This seminar will include the highlights of the program's latest release. It will be illustrated how Summit Design products can provide a high-level C/C++ and SystemC functional modelling design and verification environment, enabling engineers to analyse system concepts before the implementation stage. The seminar will show how mixed SystemC and HDL simulation can be done, along with solutions for hardware/software development. • HDL new features: Connectivity Table Editor. Xemacs full integration. New NCsim ...

  6. Technical Training Seminar

    CERN Multimedia

    2003-01-01

    Thursday 4 September From 14:00 to 17:00 - Training Centre Auditorium bldg. 593, room 11 The Summit Design VisualElite 4.0 Release Jean Marie St Paul / SUMMIT DESIGN, Europe, Technical Manager Michel Delcroix / SUMMIT DESIGN, Southern Europe, Sales F-95015 CERGY PONTOISE, France Summit Design is an important EDA digital hardware design tool supplier, and the industry leader in the emerging Electronic System Level design domain. Its VisualElite program has been used at CERN for several years. This seminar will include the highlights of the program's latest release. It will be illustrated how Summit Design products can provide a high-level C/C++ and SystemC functional modelling design and verification environment, enabling engineers to analyse system concepts before the implementation stage. The seminar will show how mixed SystemC and HDL simulation can be done, along with solutions for hardware/software development. • HDL new features: Connectivity Table Editor. Xemacs full integration. New NCsi...

  7. VLLEEM-2 technical workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In order to overcome the limits of the energy-environment models, and to benefit at the same time of their past experiences, the VLEEM project proposes a genuine approach and innovative modelling tools to assess the energy-environment systems over the very long term, which are based on the strengths of existing long term energy models, but focussed on two major objectives: to describe normative futures which fit with a set of overall constraints, like the stabilisation of the concentration of green-house gases in the atmosphere, or the stabilisation of the overall inventory of plutonium and minor actinides, etc...; to describe and formalize the association of causalities necessary to bring the system from the present situation to the targeted future, through a '' back-casting '' approach. This first technical workshop presents the state of the art of the different Work Programmes. WP1:Enhancement of the Conceptual framework. WP2: Data base on conventional demand/supply technologies. WP3: Complement and up-date technology monographs. WP4: Formalization and computing of final VLEEM submodels. WP5: Case study 2030, 2050, 2100. (A.L.B.)

  8. Technical approach document

    International Nuclear Information System (INIS)

    1988-04-01

    This document describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement Remedial Action Plans (RAPs) and final designs that comply with EPS standards. This document is a revision to the original document. Major revisions were made to the sections in riprap selection and sizing, and ground-water; only minor revisions were made to the remainder of the document. The US Nuclear Regulatory Commission (NRC) has prepared a Standard Review Plan (NRC-SRP) which describes factors to be considered by the NRC in approving the RAP. Sections 3.0, 4.0, 5.0, and 7.0 of this document are arranged under the same headings as those used in the NRC-SRP. This approach is adopted in order to facilitate joint use of the documents. Section 2.0 (not included in the NRC-SRP) discusses design considerations; Section 3.0 describes surface-water hydrology and erosion control; Section 4.0 describes geotechnical aspects of pile design; Section 5.0 discusses the Alternate Site Selection Process; Section 6.0 deals with radiological issues (in particular, the design of the radon barrier); Section 7.0 discusses protection of groundwater resources; and Section 8.0 discusses site design criteria for the RAC

  9. AIMES Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Katz, Daniel S [Univ. of Illinois, Urbana-Champaign, IL (United States). National Center for Supercomputing Applications (NCSA); Jha, Shantenu [Rutgers Univ., New Brunswick, NJ (United States); Weissman, Jon [Univ. of Minnesota, Minneapolis, MN (United States); Turilli, Matteo [Rutgers Univ., New Brunswick, NJ (United States)

    2017-01-31

    This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large-scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable and interoperable distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.

  10. Technical planning activity: Final report

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

  11. Technical planning activity: Final report

    International Nuclear Information System (INIS)

    1987-01-01

    In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements

  12. Training of technical staff and technical staff managers

    International Nuclear Information System (INIS)

    Moody, G.F.

    1991-01-01

    The purpose of Technical Staff and Technical Staff Managers training is to provide job skills enhancement to individuals selected to fill key technical positions within a nuclear utility. This training is unique in that unlike other training programs accredited by the National Academy for Nuclear Training, it does not lead to specific task qualification. The problems encountered when determining the student population and curriculum are a direct result of this major difference. Major problems encountered are determining who should attend the training, what amount of training is necessary and sufficient, and how to obtain the best feedback in order to effect substantive program improvements. These topics will be explored and possible solutions discussed

  13. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Aristos Aristidou Natureworks); Robert Kean (NatureWorks); Tom Schechinger (IronHorse Farms, Mat); Stuart Birrell (Iowa State); Jill Euken (Wallace Foundation & Iowa State)

    2007-10-01

    The two main objectives of this project were: 1) to develop and test technologies to harvest, transport, store, and separate corn stover to supply a clean raw material to the bioproducts industry, and 2) engineer fermentation systems to meet performance targets for lactic acid and ethanol manufacturers. Significant progress was made in testing methods to harvest corn stover in a “single pass” harvest mode (collect corn grain and stover at the same time). This is technically feasible on small scale, but additional equipment refinements will be needed to facilitate cost effective harvest on a larger scale. Transportation models were developed, which indicate that at a corn stover yield of 2.8 tons/acre and purchase price of $35/ton stover, it would be unprofitable to transport stover more than about 25 miles; thus suggesting the development of many regional collection centers. Therefore, collection centers should be located within about 30 miles of the farm, to keep transportation costs to an acceptable level. These collection centers could then potentially do some preprocessing (to fractionate or increase bulk density) and/or ship the biomass by rail or barge to the final customers. Wet storage of stover via ensilage was tested, but no clear economic advantages were evident. Wet storage eliminates fire risk, but increases the complexity of component separation and may result in a small loss of carbohydrate content (fermentation potential). A study of possible supplier-producer relationships, concluded that a “quasi-vertical” integration model would be best suited for new bioproducts industries based on stover. In this model, the relationship would involve a multiyear supply contract (processor with purchase guarantees, producer group with supply guarantees). Price will likely be fixed or calculated based on some formula (possibly a cost plus). Initial quality requirements will be specified (but subject to refinement).Producers would invest in harvest

  14. CTBT technical issues handbook

    International Nuclear Information System (INIS)

    Zucca, J.J.

    1994-05-01

    The purpose of this handbook is to give the nonspecialist in nuclear explosion physics and nuclear test monitoring an introduction to the topic as it pertains to a Comprehensive Test Ban Treaty (CTBT). The authors have tried to make the handbook visually oriented, with figures paired to short discussions. As such, the handbook may be read straight through or in sections. The handbook covers four main areas and ends with a glossary, which includes both scientific terms and acronyms likely to be encountered during CTBT negotiations. The following topics are covered: (1) Physics of nuclear explosion experiments. This is a description of basic nuclear physics and elementary nuclear weapon design. Also discussed are testing practices. (2) Other nuclear experiments. This section discusses experiments that produce small amounts of nuclear energy but differ from explosion experiments discussed in the first chapter. This includes the type of activities, such as laser fusion, that would continue after a CTBT is in force. (3) Monitoring tests in various environments. This section describes the different physical environments in which a test could be conducted (underground, in the atmosphere, in space, underwater, and in the laboratory); the sources of non-nuclear events (such as earthquakes and mining operations); and the opportunities for evasion. (4) On-site inspections. A CTBT is likely to include these inspections as an element of the verification provisions, in order to resolve the nature of ambiguous events. This chapter describes some technical considerations and technologies that are likely to be useful. (5) Selecting verification measures. This chapter discusses the uncertain nature of the evidence from monitoring systems and how compliance judgments could be made, taking the uncertainties into account. It also discusses how to allocate monitoring resources, given the likelihood of testing by various countries in various environments

  15. RAMP 2005 technical report

    International Nuclear Information System (INIS)

    2006-01-01

    This technical report provided details of all monitoring activities conducted by the Regional Aquatics Monitoring Program (RAMP), which was initiated in 1997 to examine the impacts of oil sands mining development on aquatic systems in the region. RAMP's objective is to integrate aquatic monitoring activities in order to identify long-term trends and regional issues related to the environment in the Regional Municipality of Wood Buffalo. In 2005, RAMP focused on key components of boreal aquatic ecosystems. This report provided full outlines of all climate and hydrology monitoring activities; water and sedimentation analyses; and studies of benthic communities in rivers, lakes, and deltas. Sets of measurements endpoints were used to represent the health and integrity of valued environmental resources. Satellite imager was used to estimate activities related to oil sands developments. The report was divided into subsections which related monitoring activities for various rivers and tributaries in the region. Small and negligible calculated changes were observed in hydrologic conditions in the Athabasca River mainstem. No discernible changes in water and sediment quality were observed that could positively be ascribed to oil sands developments in the region. Very little evidence suggested that fish populations had changed as a result of increased activities in the region. The influence of oil sands development activities on the aquatic resources of the Athabasca River mainstem were minor and mostly undetectable. The results of fish tissue studies from the lower Athabasca River showed that concentrations of mercury in fish tissues occurred at levels that posed a high risk to subsistence fishers. A higher number of metal concentrations in some lakes in the region was attributed to natural causes. The results of a sentinel species monitoring program conducted at the Ells River watershed were also included. Recommendations for further refining RAMP programs were also

  16. Technical and economic guidelines

    International Nuclear Information System (INIS)

    1978-01-01

    This paper proposes technical and economic data and analysis for use in comparing the nuclear systems considered in INFCE. It suggests that a relatively detailed set of characteristics be developed for each system. An alternative to this approach is to concentrate on comparing the characteristic of most interest to INFCE, using a differential comparison to established systems (such as the LWR and HWR) where possible. This would avoid the repetitive analysis of design characteristics that are common to many systems. In making the INFCE comparisons it would still be appropriate that a selected set of information, pertinent to the primary assessment factors under consideration, be developed for each nuclear system. This selected set, much more limited than that set forth in the body of this paper, would include overall descriptions of the reactor and fuel cycle facilities, as well as specific information on resource utilization, flow of nuclear materials, and other areas to be determined by the Working Group. On the other hand, in areas such as costs, nuclear safety, and environmental impacts, it would not be intended that information be developed at a level of detail comparable to that resulting from a detailed design of each system being compared. Instead, the detailed set of data identified in this paper can serve as a check list to assure that all pertinent characteristics are considered, at least on a differential basis; more detailed assessments would be needed only where the differences have substantial impact. Thus this paper asks for more detail than will probably be appropriate for many contributed papers

  17. Using Technical Performance Measures

    Science.gov (United States)

    Garrett, Christopher J.; Levack, Daniel J. H.; Rhodes, Russel E.

    2011-01-01

    All programs have requirements. For these requirements to be met, there must be a means of measurement. A Technical Performance Measure (TPM) is defined to produce a measured quantity that can be compared to the requirement. In practice, the TPM is often expressed as a maximum or minimum and a goal. Example TPMs for a rocket program are: vacuum or sea level specific impulse (lsp), weight, reliability (often expressed as a failure rate), schedule, operability (turn-around time), design and development cost, production cost, and operating cost. Program status is evaluated by comparing the TPMs against specified values of the requirements. During the program many design decisions are made and most of them affect some or all of the TPMs. Often, the same design decision changes some TPMs favorably while affecting other TPMs unfavorably. The problem then becomes how to compare the effects of a design decision on different TPMs. How much failure rate is one second of specific impulse worth? How many days of schedule is one pound of weight worth? In other words, how to compare dissimilar quantities in order to trade and manage the TPMs to meet all requirements. One method that has been used successfully and has a mathematical basis is Utility Analysis. Utility Analysis enables quantitative comparison among dissimilar attributes. It uses a mathematical model that maps decision maker preferences over the tradeable range of each attribute. It is capable of modeling both independent and dependent attributes. Utility Analysis is well supported in the literature on Decision Theory. It has been used at Pratt & Whitney Rocketdyne for internal programs and for contracted work such as the J-2X rocket engine program. This paper describes the construction of TPMs and describes Utility Analysis. It then discusses the use of TPMs in design trades and to manage margin during a program using Utility Analysis.

  18. Engineering Technical Review Planning Briefing

    Science.gov (United States)

    Gardner, Terrie

    2012-01-01

    The general topics covered in the engineering technical planning briefing are 1) overviews of NASA, Marshall Space Flight Center (MSFC), and Engineering, 2) the NASA Systems Engineering(SE) Engine and its implementation , 3) the NASA Project Life Cycle, 4) MSFC Technical Management Branch Services in relation to the SE Engine and the Project Life Cycle , 5) Technical Reviews, 6) NASA Human Factor Design Guidance , and 7) the MSFC Human Factors Team. The engineering technical review portion of the presentation is the primary focus of the overall presentation and will address the definition of a design review, execution guidance, the essential stages of a technical review, and the overall review planning life cycle. Examples of a technical review plan content, review approaches, review schedules, and the review process will be provided and discussed. The human factors portion of the presentation will focus on the NASA guidance for human factors. Human factors definition, categories, design guidance, and human factor specialist roles will be addressed. In addition, the NASA Systems Engineering Engine description, definition, and application will be reviewed as background leading into the NASA Project Life Cycle Overview and technical review planning discussion.

  19. TECHNICAL CULTURE AND HUMAN AXJOSPHERE

    Directory of Open Access Journals (Sweden)

    ­Krystyna Chałas

    2014-11-01

    Full Text Available Technical culture is the value of each historical period. It is the subject of the ongoing development. While it is a value which is associated with different categories of values, mainly material, cognitive, social. Between culture and these three categories of values ​ there is a cognitive effect. Technical culture determines the quality of human axjosphere. The aim of this study is to show the relationships and dependencies between technical culture and the structures in which a person lives and works. It is mainly about the answer to the question of which values of technical culture are closely related to and what are the inter dependencies? The primary task is to define the concept of the technical culture and to show its teaching essence. The second task boils down to indicate the range of values ​​inherent in the culture of technology, determining the value of the technological culture and values, which are developed by the technical culture. Indication of the interaction between the technical culture and values ​​is the third task.

  20. Field convergence between technical writers and technical translators

    DEFF Research Database (Denmark)

    Gnecchi, M.; Maylath, B.; Mousten, Birthe

    2011-01-01

    As translation of technical documents continues to grow rapidly and translation becomes more automated, the roles of professional communicators and translators appear to be converging. This paper updates preliminary findings first presented at the 2008 International Professional Communication...

  1. LHC Availability 2017: Technical Stop 1 to Technical Stop 2

    CERN Document Server

    Todd, Benjamin; Apollonio, Andrea; Walsh, David John; CERN. Geneva. ATS Department

    2017-01-01

    This document summarises the LHC machine availability for the period of Technical Stop 1 (TS1) to Technical Stop 2 (TS2) in 2017. This period was dedicated to proton physics with a bunch spacing of 25ns. This note has been produced and ratified by the Availability Working Group which has complied fault information for the period in question using the Accelerator Fault Tracker.

  2. ITER technical advisory committee meeting

    International Nuclear Information System (INIS)

    Fujiwara, M.

    1999-01-01

    The ITER Technical Advisory Committee (TAC) meeting took place on December 20-22, 1999 at the Naka Joint Work Site. The objective of this meeting was to review the document 'Technical Basis for ITER-FEAT Outline Design (ODR)' issued by the Director on December 10. It was also aimed at providing the ITER Meeting scheduled for January 19-20, 2000 in Tokyo with a technical assessment of ODR and recommendations for the optimization of the anticipated plasma performance and engineering design, based on the guidelines approved by the Council in June 1998 and recommendations of the last TAC meeting

  3. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Bohdan W. Oppenheim; Rudolf Marloth

    2007-10-26

    Executive Summary The document contains Final Technical Report on the Industrial Assessment Center Program at Loyola Marymount University in Los Angeles, covering the contract period of 9/1/2002 to 11/30/2006, under the contract DE-FC36-02GO 12073. The Report describes six required program tasks, as follows: TASK 1 is a summary of the assessments performed over the life of the award: 77 assessments were performed, 595 AR were recommended, covering a very broad range of manufacturing plants. TASK 2 is a description of the efforts to promote and increase the adoption of assessment recommendations and employ innovative methods to assist in accomplishing these goals. The LMU IAC has been very successful in accomplishing the program goals, including implemented savings of $5,141,895 in energy, $10,045,411 in productivity and $30,719 in waste, for a total of $15,218,025. This represents 44% of the recommended savings of $34,896,392. TASK 3 is a description of the efforts promoting the IAC Program and enhancing recruitment efforts for new clients and expanded geographic coverage. LMU IAC has been very successful recruiting new clients covering Southern California. Every year, the intended number of clients was recruited. TASK 4 describes the educational opportunities, training, and other related activities for IAC students. A total of 38 students graduated from the program, including 2-3 graduate students every semester, and the remainder undergraduate students, mostly from the Mechanical Engineering Department. The students received formal weekly training in energy (75%) and productivity (25). All students underwent extensive safety training. All students praised the IAC experience very highly. TASK 5 describes the coordination and integration of the Center activities with other Center and IAC Program activities, and DOE programs. LMU IAC worked closely with MIT, and SDSU IAC and SFSU IAC, and enthusiastically supported the SEN activities. TASK 6 describes other tasks

  4. Innovative technical plasma applications

    International Nuclear Information System (INIS)

    Wintner, E.

    2013-01-01

    Plasma is the predominant status of matter, in stars as well as in interstellar space. In science, it was only recognized rather late as a specific (fourth) state of matter: Sir William Crookes described it in 1879 as “radiant matter”, Irving Langmuir created the name “plasma” in 1928. Technically generated plasma is employed very broadly in modern technology. Some examples are Plasma Displays, Fluorescent Lamps (also the modern Energy Saving Lamps), Corona Discharges (for e.g. Ozone generation, or even engine ignition), arc welding and cutting, reactive ion etching, mass spectroscopy, ion rocket engines and many more. Very early since the development of the laser, it was also employed to generate a plasma (spark) in air or on surfaces. Generally, for this purpose at least ns (“Giant”) pulses have to be used. In more recent times, pico- and femtosecond pulses have allowed to create plasma very easily and effectively. Laser fusion may represent the ultimate application in this direction, based on highly amplified ns pulses for inertial confinement or ps pulses designed as fast igniter. The idea of employing laser pulses for the ignition of engines was attempted for the first time in 1978, although with inadequate tools like the CO2 laser. After a long time of inactivity in this field, about 10 years ago a few institutions like Vienna University of Technology first resumed this approach with the help of modern type solid-state lasers and started systematic investigations around the idea of laser ignition of internal combustion engines. Now, this technique has reached a high degree of maturity; remaining problems lie on the development level and are to be solved soon. Ambitious product development by leading engine producers or ignition equipment suppliers has been started world-wide since several years and, as a result, in one or two years laser ignition will probably be imple-mented into high power gas engines or, somewhat later, high-priced automotive

  5. Who recognises technical standards in TTIP?

    NARCIS (Netherlands)

    Purnhagen, K.

    2018-01-01

    Current political discussions on the relationship of technical standards to the Transatlantic, Trade and Investment Partnership (TTIP) concern the question whether TTIP can provide a transatlantic level playing field for technical standards, and whether this will negatively affect technical

  6. Engineering Technical Support Center (ETSC)

    Science.gov (United States)

    ETSC is EPA’s technical support and resource centers responsible for providing specialized scientific and engineering support to decision-makers in the Agency’s ten regional offices, states, communities, and local businesses.

  7. Hydrogen Storage Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The mission of the Hydrogen Storage Technical Team is to accelerate research and innovation that will lead to commercially viable hydrogen-storage technologies that meet the U.S. DRIVE Partnership goals.

  8. ATR Technical Specification Upgrade Program

    International Nuclear Information System (INIS)

    McCracken, R.T.; Durney, J.L.; Freund, G.A.

    1990-01-01

    The Advanced Test Reactor (ATR) is a 250 MW, uranium-aluminum fueled test reactor which began full power operation in 1969. The initial operation was controlled by an Operating Limits document based on the original Safety Analysis Report. Additional safety bases were later developed to support Technical Specifications which were approved and implemented in 1977. The Technical Specifications which were initially developed with content and format specified in ANSI/ANS--15.1, ''The Development of Technical Specifications for Research Reactors.'' The safety basis documentation and the Technical Specifications have been updated as required to maintain them current with the ATR facility configuration. All revisions have been made with a content, format and style consistent with the original. A major, two-phase program to upgrade the content, format and style is in progress. This paper describes the first phase of this program

  9. Technical challenges for dismantlement verification

    International Nuclear Information System (INIS)

    Olinger, C.T.; Stanbro, W.D.; Johnston, R.G.; Nakhleh, C.W.; Dreicer, J.S.

    1997-01-01

    In preparation for future nuclear arms reduction treaties, including any potential successor treaties to START I and II, the authors have been examining possible methods for bilateral warhead dismantlement verification. Warhead dismantlement verification raises significant challenges in the political, legal, and technical arenas. This discussion will focus on the technical issues raised by warhead arms controls. Technical complications arise from several sources. These will be discussed under the headings of warhead authentication, chain-of-custody, dismantlement verification, non-nuclear component tracking, component monitoring, and irreversibility. The authors will discuss possible technical options to address these challenges as applied to a generic dismantlement and disposition process, in the process identifying limitations and vulnerabilities. They expect that these considerations will play a large role in any future arms reduction effort and, therefore, should be addressed in a timely fashion

  10. Polar source analysis : technical memorandum

    Science.gov (United States)

    2017-09-29

    The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

  11. NASA Technical Reports Server (NTRS)

    Data.gov (United States)

    National Aeronautics and Space Administration — The NTRS is a valuable resource for researchers, students, educators, and the public to access NASA's current and historical technical literature and engineering...

  12. Bibliography of Technical Reports - 1974,

    Science.gov (United States)

    The bibliography lists all Technical Reports prepared by the Woods Hole Oceanographic Institution in the year 1974. It includes an author index , and also a key relating Reports to ’Contribution Numbers’.

  13. Saturation curve of SiO2 component in rutile-type GeO2: A recoverable high-temperature pressure standard from 3 GPa to 10 GPa

    International Nuclear Information System (INIS)

    Leinenweber, Kurt; Gullikson, Amber L.; Stoyanov, Emil; Malik, Abds-Sami

    2015-01-01

    The accuracy and precision of pressure measurements and the pursuit of reliable and readily available pressure scales at simultaneous high temperatures and pressures are still topics in development in high pressure research despite many years of work. In situ pressure scales based on x-ray diffraction are widely used but require x-ray access, which is lacking outside of x-ray beam lines. Other methods such as fixed points require several experiments to bracket a pressure calibration point. In this study, a recoverable high-temperature pressure gauge for pressures ranging from 3 GPa to 10 GPa is presented. The gauge is based on the pressure-dependent solubility of an SiO 2 component in the rutile-structured phase of GeO 2 (argutite), and is valid when the argutite solid solution coexists with coesite. The solid solution varies strongly in composition, mainly in pressure but also somewhat in temperature, and the compositional variations are easily detected by x-ray diffraction of the recovered products because of significant changes in the lattice parameters. The solid solution is measured here on two isotherms, one at 1200 °C and the other at 1500 °C, and is developed as a pressure gauge by calibrating it against three fixed points for each temperature and against the lattice parameter of MgO measured in situ at a total of three additional points. A somewhat detailed thermodynamic analysis is then presented that allows the pressure gauge to be used at other temperatures. This provides a way to accurately and reproducibly evaluate the pressure in high pressure experiments and applications in this pressure-temperature range, and could potentially be used as a benchmark to compare various other pressure scales under high temperature conditions. - Graphical abstract: The saturation curve of SiO 2 in TiO 2 shows a strong pressure dependence and a strong dependence of unit cell volume on composition. This provides an opportunity to use this saturation curve as a

  14. Technical management courses (before July)

    CERN Multimedia

    2015-01-01

    Please find below the courses in the field of technical management scheduled before July and which have places available.       For more details about a course and to register, please go to the Training Catalogue. If you need a course which is not in the catalogue, please contact your supervisor, your Departmental Training Officer or HR-LD at Technical.Management.Training@cern.ch.

  15. Guam Initial Technical Assessment Report

    Energy Technology Data Exchange (ETDEWEB)

    Baring-Gould, I.; Conrad, M.; Haase, S.; Hotchkiss, E.; McNutt, P.

    2011-04-01

    Under an interagency agreement, funded by the Department of Interior's (DOI) Office of Insular Affairs (OIA), the National Renewable Energy Laboratory (NREL) was tasked to deliver technical assistance to the island of Guam by conducting an island initial technical assessment that would lay out energy consumption and production data and establish a baseline. This assessment will be used to conduct future analysis and studies by NREL that will estimate energy efficiency and renewable energy potential for the island of Guam.

  16. Technical framework for groundwater restoration

    International Nuclear Information System (INIS)

    1991-04-01

    This document provides the technical framework for groundwater restoration under Phase II of the Uranium Mill Tailings Remedial Action (UMTRA) Project. A preliminary management plan for Phase II has been set forth in a companion document titled ''Preplanning Guidance Document for Groundwater Restoration''. General principles of site characterization for groundwater restoration, restoration methods, and treatment are discussed in this document to provide an overview of standard technical approaches to groundwater restoration

  17. Environmental impacts on technical products

    International Nuclear Information System (INIS)

    1991-01-01

    The interaction between an object and its environment is examined by methods of environment simulation. With regard to possible synergisms, technical considerations and holistic thinking are essential. Environmental simulation is mainly concerned with questions of ability to function and the service life of technical products in their environment. The environmental simulation is used to discover cause/effect mechanisms in ageing and weathering processes. Questions of artificial ageing and speeded up time tests play a great part here. (orig.) [de

  18. NetView technical research

    Science.gov (United States)

    1993-01-01

    This is the Final Technical Report for the NetView Technical Research task. This report is prepared in accordance with Contract Data Requirements List (CDRL) item A002. NetView assistance was provided and details are presented under the following headings: NetView Management Systems (NMS) project tasks; WBAFB IBM 3090; WPAFB AMDAHL; WPAFB IBM 3084; Hill AFB; McClellan AFB AMDAHL; McClellan AFB IBM 3090; and Warner-Robins AFB.

  19. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Howe, Gary [RTI International, Research Triangle Park, NC (United States); Albritton, John [RTI International, Research Triangle Park, NC (United States); Denton, David [RTI International, Research Triangle Park, NC (United States); Turk, Brian [RTI International, Research Triangle Park, NC (United States); Gupta, Raghubir [RTI International, Research Triangle Park, NC (United States)

    2018-01-31

    technology has great potential to provide clean syngas from coal and petcoke-based gasification at increased efficiency and at significantly lower capital and operating costs than conventional syngas cleanup technologies. However, before the technology can be deemed ready for scale-up to a full commercial-scale demonstration, additional R&D testing is needed at the site to address the following critical technical risks: WDP sorbent stability and performance; Impact of WDP on downstream cleanup and conversion steps; Metallurgy and refractory; Syngas cleanup performance and controllability; Carbon capture performance and additional syngas cleanup The proposed plan to acquire this additional R&D data involves: Operation of the units to achieve an additional 3,000 hours of operation of the system within the performance period, with a target of achieving 1,000 hours of those hours via continuous operation of the entire integrated pre-commercial demonstration system; Rapid turnaround of repairs and/or modifications required as necessary to return any specific unit to operating status with documentation and lessons learned to support technology maturation, and; Proactive performance of maintenance activities during any unplanned outages and if possible while operating.

  20. Reader-Centered Technical Writing

    Science.gov (United States)

    Narayanan, M.

    2012-12-01

    Technical writing is an essential part of professional communication and in recent years it has shifted from a genre-based approach. Formerly, technical writing primarily focused on generating templates of documents and sometimes it was creating or reproducing traditional forms with minor modifications and updates. Now, technical writing looks at the situations surrounding the need to write. This involves deep thinking about the goals and objectives of the project on hand. Furthermore, one observes that it is very important for any participatory process to have the full support of management. This support needs to be well understood and believed by employees. Professional writing may be very persuasive in some cases. When presented in the appropriate context, technical writing can persuade a company to improve work conditions ensuring employee safety and timely production. However, one must recognize that lot of professional writing still continues to make use of reports and instruction manuals. Normally, technical and professional writing addresses four aspects. Objective: The need for generating a given professionally written technical document and the goals the document is expected to achieve and accomplish. Clientele: The clientele who will utilize the technical document. This may include the people in the organization. This may also include "unintended readers." Customers: The population that may be affected by the content of the technical document generated. This includes the stakeholders who will be influenced. Environment: The background in which the document is created. Also, the nature of the situation that warranted the generation of the document. Swiss Psychologist Jean Piaget's view of Learning focuses on three aspects. The author likes to extend Jean Piaget's ideas to students, who are asked to prepare and submit Reader-Centered Technical Writing reports and exercises. Assimilation: Writers may benefit specifically, by assimilating a new object into

  1. Ageing management technical information investigations

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    In February 2013, there are 50 units of commercial nuclear power plants (NPPs) in Japan. We enter into a period that 20 units of them are operating for more than 30 years. Currently, regulation imposes utilities to conduct ageing technical evaluations of each unit before operation of 30 years from the commissioning, to develop the long term maintenance management policy for next 10 years and to submit to the regulatory authority the policy with the report on ageing management technical evaluation (AMTE) for each NPP. It is necessary for regulatory side to develop technical information bases incorporating latest technical knowledge as operating experiences in domestic and abroad on ageing of the plants necessary to conduct reviews of AMTE for each unit. Based on these standpoints, technical information bases investigations have been conducted from the viewpoints of material degradation of ageing NPPs. In order to develop scientific regulator judgment bases related to ageing management (AM) and long-term operation (LTO), investigations on latest information on ageing management in domestic and abroad are conducted and a set of documents including technical evaluation review manuals necessary to conduct AMTE are prepared. To utilize the results of the investigations for ageing technical evaluation, database including latest information related to AM and LTO are developed, ran and operated. In addition, investigations related to Fugen nuclear plant, under decommissioning plants, investigations on mechanism of stress corrosion cracking (SCC), thermal ageing and preventive technologies for SCC, detection and diagnosis technology for ageing degradation and condition monitoring technology are performed to validate and confirm effectiveness of the technologies. (author)

  2. Technical Support and Transfer of Geothrmal Technical Knowledge and Information

    Energy Technology Data Exchange (ETDEWEB)

    John W. Lund; Toni" Boyd

    2007-11-14

    The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

  3. CEEM Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Bowers, John [Univ. of California, Santa Barbara, CA (United States)

    2014-11-26

    concentrating photovoltaic applications thathave substantially higher efficiency than single substrate cells made of elemental semiconductors such as silicon. This task required the development of new cell bonding methods with excellent coupling of both photons and electrons between the sub-cells. To accomplish this, we developed (1) GaInN solar cells with enhanced performance by using quantum-well absorbers and front-surface optical texturing, (2) a hybrid "pillar-array" bond which uses an array of metal pillars for electrical coupling, and (3) a "hybrid moth-eye" optical coating which combines the benefits of nano-imprinted moth-eye coatings and traditional multilayer coatings. The technical effectiveness was assessed by measurement of the photovoltaic efficiency of solar cells made using these techniques; the ultrahigh efficiencies targeted by this work are of compelling economic value for concentrating photovoltaics.

  4. 49 CFR 552.6 - Technical review.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Technical review. 552.6 Section 552.6... § 552.6 Technical review. The appropriate Associate Administrator conducts a technical review of the petition. The technical review may consist of an analysis of the material submitted, together with...

  5. ITER technical advisory committee meeting

    International Nuclear Information System (INIS)

    Fujiwara, M.

    2001-01-01

    The 17th Meeting of the ITER Technical Advisory Committee (TAC-17) was held on February 19-22, the ITER Garching Work Site in Germany. The objective of the meeting was to review the Draft Final Design Report of ITER-FEAT and assess the ability of the self-consistent overall design both to satisfy the technical objectives previously defined and to meet the cost limitations. TAC-17 was also organized to confirm that the design and critical elements, with emphasis on the key recommendations made at previous TAC meetings, are such as to extend the confidence in starting ITER construction. It was also intended to provide the ITER Council, scheduled to meet on 27 and 28 February in Toronto, with a technical assessment and key recommendations of the above mentioned report

  6. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    KRIPPS, L.J.

    2005-03-03

    This document describes the qualitative evaluation of frequency and consequences for DST and SST representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant structures, systems and components (SSCs) and/or technical safety requirements (TSRs) were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support WP-13033, Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  7. Technical support and emergency centre

    International Nuclear Information System (INIS)

    Bohun, L.; Kapisovsk y, M.

    1997-01-01

    This paper presents technical support and emergency management center which will be on two places: Mochovce NPP Emergency Centre (Technical support center and Support working center) and Reserve Emergency Centre in Levice (Reserve emergency center and Environmental Evaluation Center). The main aims of the emergency management centers are: the management and coordination of all persons and organisations; provision of the all information needed to evaluation of the accident and its mitigation; continuous evaluation of the potential or real radiological consequences; taking measure for an early notification of the governmental bodies and the organizations, warning and protection of the public; and other aims. In the next part the data for technical support and emergency centre are discussed

  8. Maps showing geology, oil and gas fields, and geological provinces of South America

    Science.gov (United States)

    Schenk, C. J.; Viger, R.J.; Anderson, C.P.

    1999-01-01

    This digitally compiled map includes geology, geologic provinces, and oil and gas fields of South America. The map is part of a worldwide series on CD-ROM by World Energy Project released of the U.S. Geological Survey . The goal of the project is to assess the undiscovered, technically recoverable oil and gas resources of the world and report these results by the year 2000. For data management purposes the world is divided into eight energy regions corresponding approximately to the economic regions of the world as defined by the U.S. Department of State. South America (Region 6) includes Argentina, Bolivia, Brazil, Chile, Columbia, Ecuador, Falkland Islands, French Guiana, Guyuna, Netherlands, Netherlands Antilles, Paraguay, Peru, Suriname, Trinidad and Tobago, Uruguay, and Venezuela.

  9. Assessment of Appalachian basin oil and gas resources: Carboniferous Coal-bed Gas Total Petroleum System: Chapter G.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Milici, Robert C.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    The Carboniferous Coal-bed Gas Total Petroleum System, which lies within the central and southern Appalachian basin, consists of the following five assessment units (AUs): (1) the Pocahontas Basin AU in southern West Virginia, eastern Kentucky, and southwestern Virginia; (2) the Central Appalachian Shelf AU in Tennessee, eastern Kentucky, and southern West Virginia; (3) the East Dunkard (Folded) AU in western Pennsylvania and northern West Virginia; (4) the West Dunkard (Unfolded) AU in Ohio and adjacent parts of Pennsylvania and West Virginia; and (5) the Appalachian Anthracite and Semi-Anthracite AU in Pennsylvania and Virginia. Only two of these assessment units were assessed quantitatively by the U.S. Geological Survey (USGS) in the National Oil and Gas Assessment in 2002. The USGS estimated the Pocahontas Basin AU and the East Dunkard (Folded) AU to contain a mean of about 3.6 and 4.8 trillion cubic feet (TCF) of undiscovered, technically recoverable gas, respectively.

  10. U.S. Geological Survey input-data forms for the assessment of the Spraberry Formation of the Midland Basin, Permian Basin Province, Texas, 2017

    Science.gov (United States)

    Marra, Kristen R.

    2017-10-24

    In 2017, the U.S. Geological Survey (USGS) completed an updated assessment of undiscovered, technically recoverable oil and gas resources in the Spraberry Formation of the Midland Basin (Permian Basin Province) in southwestern Texas (Marra and others, 2017). The Spraberry Formation was assessed using both the standard continuous (unconventional) and conventional methodologies established by the USGS for three assessment units (AUs): (1) Lower Spraberry Continuous Oil Trend AU, (2) Middle Spraberry Continuous Oil Trend AU, and (3) Northern Spraberry Conventional Oil AU. The revised assessment resulted in total estimated mean resources of 4,245 million barrels of oil, 3,112 billion cubic feet of gas, and 311 million barrels of natural gas liquids. The purpose of this report is to provide supplemental documentation of the input parameters used in the USGS 2017 Spraberry Formation assessment.

  11. Technical Manual: easyCBM. Technical Report #1408

    Science.gov (United States)

    Anderson, Daniel; Alonzo, Julie; Tindal, Gerald; Farley, Dan; Irvin, P. Shawn; Lai, Cheng-Fei; Saven, Jessica L.; Wray, Kraig A.

    2014-01-01

    Since the easyCBM© learning system was first published in 2006, over $8 million of federal funding (both from the Office of Special Education Programs and more recently from the Institute of Education Sciences) has been used to develop, study, and refine the assessments available on the system. This Technical Manual summarizes the ongoing research…

  12. Integrated risk - healthy technical conscience

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, P. [Institute of Nuclear Power Operations, Atlanta, GA (United States)

    2015-07-01

    The personal obligation leaders and individuals internalize and exercise to ensure plant operation, maintenance, and engineering activities are conducted in a manner consistent with plant design, emergency response strategies, technical requirements and that preserve operating, design and safety margins. Technical errors are increasing, both in number and significance. Causes are common at many utilities. The majority of these engineering human performance weaknesses have not had immediate impact on station reliability and safety (not self-revealing). In some recent projects, the same weaknesses affected a station's viability.

  13. Management of technical information department

    Energy Technology Data Exchange (ETDEWEB)

    Kim, T H; Han, D H; Moon, H W [and others

    1997-03-01

    This report introduces technical information activities in 1996. They are composed of basic tasks and applied tasks. 1. Basic activities - acquisition, cataloging, and Information services 2. Management of KAERI-TIPS (Technical Information Processing System) 3. Construction of the database for nuclear-related Information 4. Role of Specialized Nuclear Information Center in the field of nuclear energy and cooperation with INIS section of IAEA 5. Beside above activities, in 1996 TID homepage was opened and online document delivery service was provided. (author). 25 tabs., 17 figs.

  14. Management of technical information department

    International Nuclear Information System (INIS)

    Kim, T. H.; Han, D. H.; Moon, H. W.

    1997-03-01

    This report introduces technical information activities in 1996. They are composed of basic tasks and applied tasks. 1. Basic activities - acquisition, cataloging, and Information services 2. Management of KAERI-TIPS (Technical Information Processing System) 3. Construction of the database for nuclear-related Information 4. Role of Specialized Nuclear Information Center in the field of nuclear energy and cooperation with INIS section of IAEA 5. Beside above activities, in 1996 TID homepage was opened and online document delivery service was provided. (author). 25 tabs., 17 figs

  15. Physical foundations of technical acoustics

    CERN Document Server

    Malecki, I

    1969-01-01

    Physical Foundations of Technical Acoustics discusses theoretical foundations of acoustical engineering. It is not so much a technical compendium as a systematic statement of physical laws so conceived that technologists might find in it all the information they need to become acquainted with the physical meaning and mathematical expression of phenomena they encounter in their work. To facilitate the acquirement of notions, which lie beyond a layman's grasp, the plan of narration adopted consists in beginning with the simplest idealized cases and then gradually moving on to the truest possibl

  16. Trojan technical specification verification project

    International Nuclear Information System (INIS)

    Bates, L.; Rickenback, M.

    1991-01-01

    The Trojan Technical Specification Verification (TTSV) project at the Trojan plant of Portland General Electric Company was motivated by the recognition that many numbers in the Trojan technical specifications (TTS) potentially lacked the consideration of instrument- and/or process-related errors. The plant setpoints were known to consider such errors, but many of the values associated with the limiting conditions for operation (LCO) did not. In addition, the existing plant instrument error analyses were based on industry values that do not reflect the Trojan plant-specific experience. The purpose of this project is to ensure that the Trojan plant setpoint and LCO values include plant-specific instrument error

  17. System for technical innovation support

    International Nuclear Information System (INIS)

    2011-08-01

    This book lists field of support system, which includes tax, development work, basic research project, industrial technology, information and communications field, energy field, part and materials field, local industry, the small and medium business such as technical development field, and industry-university collaboration like summary of investment and financing support and guarantee, support of manpower such as brain pool and contact Korea, support of technique like development technology and strategy for patent, support on certification such as company and technical goods, purchase support.

  18. Technical progress and climatic change

    International Nuclear Information System (INIS)

    Ausubel, J.H.

    1995-01-01

    The global warming debate has neglected and thus underestimated the importance of technical change in considering reduction in greenhouse gases and adaptation to climate change. Relevant quantitative cases of long-run technical change during the past 100 years are presented in computing, communications, transport, energy, and agriculture. A noteworthy technological trajectory is that of decarbonization, or decreasing carbon intensity of primary energy. If human societies have not yet reached the end of the history of technology, the cost structure for mitigation and adaptation changes could be cheap. (Author)

  19. How to be an Effective Technical Writer?

    OpenAIRE

    M Solaiman Ali; Dheya Al-Othmany

    2012-01-01

    Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations). Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical w...

  20. Technical innovation and policy of scientific technique

    International Nuclear Information System (INIS)

    Song, Wi Jin

    2006-04-01

    This book deals with system of innovation and policy of scientific technology : main view point and Topic, technical politics and technical learning, spread of internet and change of structure in information and communications industry, characteristic of technical innovation of software as open source, transfer into national innovation system, change of activity of public scientific technology, theory on technical innovation, evolution of technical innovation policy and participation of civil.

  1. Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Overview of scientific and technical program

    Science.gov (United States)

    Hunter, R.B.; Collett, T.S.; Boswell, R.; Anderson, B.J.; Digert, S.A.; Pospisil, G.; Baker, R.; Weeks, M.

    2011-01-01

    The Mount Elbert Gas Hydrate Stratigraphic Test Well was drilled within the Alaska North Slope (ANS) Milne Point Unit (MPU) from February 3 to 19, 2007. The well was conducted as part of a Cooperative Research Agreement (CRA) project co-sponsored since 2001 by BP Exploration (Alaska), Inc. (BPXA) and the U.S. Department of Energy (DOE) in collaboration with the U.S. Geological Survey (USGS) to help determine whether ANS gas hydrate can become a technically and commercially viable gas resource. Early in the effort, regional reservoir characterization and reservoir simulation modeling studies indicated that up to 0.34 trillion cubic meters (tcm; 12 trillion cubic feet, tcf) gas may be technically recoverable from 0.92 tcm (33 tcf) gas-in-place within the Eileen gas hydrate accumulation near industry infrastructure within ANS MPU, Prudhoe Bay Unit (PBU), and Kuparuk River Unit (KRU) areas. To further constrain these estimates and to enable the selection of a test site for further data acquisition, the USGS reprocessed and interpreted MPU 3D seismic data provided by BPXA to delineate 14 prospects containing significant highly-saturated gas hydrate-bearing sand reservoirs. The "Mount Elbert" site was selected to drill a stratigraphic test well to acquire a full suite of wireline log, core, and formation pressure test data. Drilling results and data interpretation confirmed pre-drill predictions and thus increased confidence in both the prospect interpretation methods and in the wider ANS gas hydrate resource estimates. The interpreted data from the Mount Elbert well provide insight into and reduce uncertainty of key gas hydrate-bearing reservoir properties, enable further refinement and validation of the numerical simulation of the production potential of both MPU and broader ANS gas hydrate resources, and help determine viability of potential field sites for future extended term production testing. Drilling and data acquisition operations demonstrated that gas hydrate

  2. DOE FINAL TECHNICAL REPORT RP

    Energy Technology Data Exchange (ETDEWEB)

    RUSS PETERMAN

    2012-01-01

    The City of Georgetown Utility Systems (GUS) patnered with the private sector, the American Public Power Association (APPA) and Southwestern University to design, construct, test and monitor a solar co-generation system directly connected to the GUS electric distribution system. This report consists of the Primary Technical Report and 3 attachments.

  3. Career Satisfaction Following Technical Education

    Science.gov (United States)

    McDonald, Betty Manager

    2011-01-01

    The effect of career and technical education in the Caribbean is an area of intervention research that needs more attention. This present research is the first of its kind within the region. The study benefits from a large sample size (N = 500) conducted among a non-traditional population in the field of career development. This paper reports on…

  4. Standard Technical Specifications, Westinghouse plants

    International Nuclear Information System (INIS)

    1992-09-01

    This NUREG contains improved Standard Technical Specifications (STS) for Westinghouse Plants and documents the positions of the Nuclear Regulatory Commission based on the Westinghouse Owners Group's proposed STS. This document is the result of extensive technical meetings and discussions among the NRC staff, the Nuclear Steam Supply System (NSSS) Owners Groups, the NSSS vendors, and the Nuclear Management and Resources Council (NUMARC). The improved STS were developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. This document, Volume 3, contains the Bases for Sections 3.4--3.9 of the improved STS

  5. Career Technical Education Pathways Initiative

    Science.gov (United States)

    California Community Colleges, Chancellor's Office, 2013

    2013-01-01

    California's education system--the largest in the United States--is an essential resource for ensuring strong economic growth in the state. The Career Technical Education Pathways Initiative (referred to as the Initiative in this report), which became law in 2005, brings together community colleges, K-12 school districts, employers, organized…

  6. Technical regulation of nondestructive inspection

    International Nuclear Information System (INIS)

    1995-01-01

    It starts with the explanation of definition of nondestructive inspection and qualifications for a inspection. It lists the technical regulations of nondestructive inspections which are radiographic testing, ultrasonic flaw detecting test, liquid penetrant test, magnetic particle inspection, eddy current test visual inspection and leakage test.

  7. Defense Technical Information Center thesaurus

    Energy Technology Data Exchange (ETDEWEB)

    Dickert, J.H. [ed.] [comp.

    1996-10-01

    This DTIC Thesaurus provides a basic multidisciplinary subject term vocabulary used by DTIC to index and retrieve scientific and technical information from its various data bases and to aid DTIC`s users in their information storage and retrieval operations. It includes an alphabetical posting term display, a hierarchy display, and a Keywork Out of Context (KWOC) display.

  8. Standard Technical Specifications, Westinghouse Plants

    International Nuclear Information System (INIS)

    1992-09-01

    This NUREG contains improved Standard Technical Specifications (STS) for Westinghouse Plants and documents the positions of the Nuclear Regulatory Commission based on the Westinghouse Owners Group's proposed STS. This document is the result of extensive technical meetings and discussions among the NRC staff, the Nuclear Steam Supply System (NSSS) Owners Groups, the NSSS vendors, and the Nuclear Management and Resources Council (NUMARC). The improved STS were developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the unproved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS which contain information on safety limits, reactivity control systems, power distribution limits, and instrumentation

  9. NWMO transportation technical work program

    International Nuclear Information System (INIS)

    Hatton, C.

    2015-01-01

    This paper describes technical work program for the transportation nuclear waste by the Nuclear Waste Management Organization (NWMO). Transportation work program involves risk assessment which under normal conditions involves dose assessment to the worker and the public as well as consideration of transportation system routing and operations. It also involves possible accident scenarios using forensic modelling and probability analysis.

  10. Hydrogen Delivery Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The mission of the Hydrogen Delivery Technical Team (HDTT) is to enable the development of hydrogen delivery technologies, which will allow for fuel cell competitiveness with gasoline and hybrid technologies by achieving an as-produced, delivered, and dispensed hydrogen cost of $2-$4 per gallon of gasoline equivalent of hydrogen.

  11. Socio-technical security metrics

    NARCIS (Netherlands)

    Gollmann, D.; Herley, C.; Koenig, V.; Pieters, W.; Sasse, M.A.

    2015-01-01

    Report from Dagstuhl seminar 14491. This report documents the program and the outcomes of Dagstuhl Seminar 14491 “Socio-Technical Security Metrics”. In the domain of safety, metrics inform many decisions, from the height of new dikes to the design of nuclear plants. We can state, for example, that

  12. Design mentoring tool : [technical summary].

    Science.gov (United States)

    2011-01-01

    In 2004 a design engineer on-line mentoring tool was developed and implemented The purpose of the tool was to assist senior engineers mentoring new engineers to the INDOT design process and improve their technical competency. This approach saves seni...

  13. Visualizing interdependencies in technical design

    NARCIS (Netherlands)

    Oosterman, B.J.; Gaalman, G.J.C.; Kuijpers, F.P.J.; Riiahuhta, A.; Pulkkinen, A.

    2001-01-01

    The control and understanding of complex design processes is an important issue in practice and theory. Recent research shows that documentation and analysis of technical interactions between design tasks (using Design Structure Matrices) gives a thorough understanding of the underlying complex

  14. Mechanical Engineering Department technical review

    Energy Technology Data Exchange (ETDEWEB)

    Carr, R.B.; Abrahamson, L.; Denney, R.M.; Dubois, B.E (eds.)

    1982-01-01

    Technical achievements and publication abstracts related to research in the following Divisions of Lawrence Livermore Laboratory are reported in this biannual review: Nuclear Fuel Engineering; Nuclear Explosives Engineering; Weapons Engineering; Energy Systems Engineering; Engineering Sciences; Magnetic Fusion Engineering; and Material Fabrication. (LCL)

  15. Technical diagnostics of steam turbines

    International Nuclear Information System (INIS)

    Vlckova, B.; Drahy, J.

    1987-01-01

    This paper deals with practical experience in application of technical diagnostics methods to steam turbines, in particular using pedestal and shaft vibration measurements as well as estimation of bearing metal temperature and ultrasound emission signals. An estimation of effectiveness of the diagnostics methods used is given on the basis of experimental investigations made on a 30-MW turbine. (author)

  16. Reforming Technical and Technological Education.

    Science.gov (United States)

    Wilson, David N.

    1993-01-01

    Review of technical and technological educational reform in Brazil, Canada, Germany, Great Britain, Indonesia, Malaysia, Singapore, and Sweden shows that reform takes time to complete effectively, long-term approaches are needed, and reform is linked to industrial development, regional cooperation, and decentralized decision making. (SK)

  17. TADS: Technical Assistance Development System.

    Science.gov (United States)

    Epting, Rosemary, Ed.

    Described is the Technical Assistance Development System (TADS), a component of the Frank Porter Graham Child Development Center of the University of North Carolina at Chapel Hill which offers support services to preschool demonstration centers for handicapped children in the First Chance Network. Discussed are the four types of services offered:…

  18. Standard Technical Specifications, Westinghouse plants

    International Nuclear Information System (INIS)

    1992-09-01

    This NUREG contains improved Standard Technical Specifications (STS) for Westinghouse Plants and documents the positions of the Nuclear Regulatory Commission based on the Westinghouse Owners Group's proposed STS. This document is the result of extensive technical meetings and discussions among the NRC staff, the Nuclear Steam Supply System (NSSS) Owners Groups, the NSSS vendors, and the Nuclear Management and Resources Council (NUMARC). The improved STS were developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. This document, Volume 1, contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS

  19. Atmospheric Research 2011 Technical Highlights

    Science.gov (United States)

    2012-01-01

    The 2011 Technical Highlights describes the efforts of all members of Atmospheric Research. Their dedication to advancing Earth Science through conducting research, developing and running models, designing instruments, managing projects, running field campaigns, and numerous other activities, is highlighted in this report.

  20. The Migration of Technical Workers

    DEFF Research Database (Denmark)

    Dahl, Michael S.; Sorenson, Olav

    2010-01-01

    Using panel data on the Danish population, we estimated the revealed preferences of scientists and engineers for the places in which they choose to work. Our results indicate that these technical workers exhibit substantial sensitivity to differences in wages but that they have even stronger...

  1. Fifty years of Technical Cooperation

    International Nuclear Information System (INIS)

    2007-01-01

    The International Atomic Energy Agency (IAEA) was established in Vienna in 1957. The Statute of the IAEA, approved by 81 nations, founded the organization on three pillars: nuclear verification; safety and security; and the transfer of technology. Today, these three pillars still remain at the heart of the organization's work. However, the way in which the IAEA carries out this work, particularly with regard to technology transfer, has changed greatly over the years. When the IAEA opened for business, nuclear science and technology were in their infancy. Many Member States had no nuclear capacity at all. The IAEA's 'technical assistance' programme, as it was then known, was modest. Early projects were small in scale and short lived, focusing mainly on building human capacities and creating institutions and facilities that would support the introduction of nuclear technology in a safe and effective manner. Today, the picture is more complex. Instead of merely offering assistance, the IAEA focuses on cooperation for sustainable socioeconomic development, building on the skills and infrastructure that Member States have acquired over the past five decades. Member States are full partners in the process, guiding the IAEA's technical cooperation activities, setting national and regional priorities, and offering training opportunities and technical support to the IAEA and to other Member States. Technical cooperation between developing countries is facilitated and supported through regional cooperative agreements. Regional centres of expertise play an important role in sharing the benefits of nuclear science and technology among Member States

  2. Technical assistance contractor Management Plan

    International Nuclear Information System (INIS)

    1993-09-01

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins ampersand Beckwith Agra, Inc. (SHB Agra), and Geraghty ampersand Miller, Inc. (G ampersand M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC's groundwater technical breadth and depth, so G ampersand M was brought in to augment the team's capabilities. The TAC contract's scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC's management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls

  3. NWMO transportation technical work program

    Energy Technology Data Exchange (ETDEWEB)

    Hatton, C. [Nuclear Waste Management Organization, Toronto, ON (Canada)

    2015-07-01

    This paper describes technical work program for the transportation nuclear waste by the Nuclear Waste Management Organization (NWMO). Transportation work program involves risk assessment which under normal conditions involves dose assessment to the worker and the public as well as consideration of transportation system routing and operations. It also involves possible accident scenarios using forensic modelling and probability analysis.

  4. Technical noise supplement : TeNS : a technical supplement to the Traffic Noise Analysis Protocol.

    Science.gov (United States)

    1998-10-01

    The purpose of this Technical Noise Supplement (TeNS) is to provide technical background : information on transportation-related noise in general and highway traffic noise in : particular. It is designed to elaborate on technical concepts and procedu...

  5. Mechanical Engineering Department technical abstracts

    International Nuclear Information System (INIS)

    1984-01-01

    The Mechanical Engineering Department publishes abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). General information about the current role and activities of each of the Department's seven divisions precedes the technical abstracts. Further information about a division's work may be obtained from the division leader, whose name is given at the end of each divisional summary. The Department's seven divisions are as follows: Nuclear Test Engineering Division, Nuclear Explosives Engineering Division, Weapons Engineering Division, Energy Systems Engineering Division, Engineering Sciences Division, Magnetic Fusion Engineering Division and Materials Fabrication Division

  6. TRManager – Technical Risk Manager

    Directory of Open Access Journals (Sweden)

    Mark A. Gregory

    2009-06-01

    Full Text Available This paper presents research into the development of a new information management technique called Technical Risk Manager. Project management involves the use of processes and information management techniques to aid decision making in the pursuit of project success. Project success may be achieved by meeting time, cost or performance criteria. Current project management practices focus on achieving time and cost project success criteria by using three information management techniques developed in the 1950s: Gantt, PERT and Critical Path Method. Technical Risk Manager has been developed to provide an information management technique that may be used to aid project management decision making in the pursuit of achieving the performance project success criteria.

  7. Internal dosimetry technical basis manual

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-20

    The internal dosimetry program at the Savannah River Site (SRS) consists of radiation protection programs and activities used to detect and evaluate intakes of radioactive material by radiation workers. Examples of such programs are: air monitoring; surface contamination monitoring; personal contamination surveys; radiobioassay; and dose assessment. The objectives of the internal dosimetry program are to demonstrate that the workplace is under control and that workers are not being exposed to radioactive material, and to detect and assess inadvertent intakes in the workplace. The Savannah River Site Internal Dosimetry Technical Basis Manual (TBM) is intended to provide a technical and philosophical discussion of the radiobioassay and dose assessment aspects of the internal dosimetry program. Detailed information on air, surface, and personal contamination surveillance programs is not given in this manual except for how these programs interface with routine and special bioassay programs.

  8. Technical aspects of fuel reprocessing

    International Nuclear Information System (INIS)

    Groenier, W.S.

    1982-02-01

    The purpose of this paper is to present a brief description of fuel reprocessing and some present developments which show the reliability of nuclear energy as a long-term supply. The following topics are discussed: technical reasons for reprocessing; economic reasons for reprocessing; past experience; justification for advanced reprocessing R and D; technical aspects of current reprocessing development. The present developments are mainly directed at the reprocessing of breeder reactor fuels but there are also many applications to light-water reactor fuel reprocessing. These new developments involve totally remote operation, and maintenance. To demonstrate this advanced reprocessing concept, pilot-scale demonstration facilities are planned with commercial application occurring sometime after the year 2000

  9. Technical Training seminar: Texas Instruments

    CERN Multimedia

    2006-01-01

    Monday 6 November TECHNICAL TRAINING SEMINAR 14:00 to 17:30 - Training Centre Auditorium (bldg. 593) Texas Instruments Technical Seminar Michael Scholtholt, Field Application Engineer / TEXAS INSTRUMENTS (US, D, CH) POWER - A short approach to Texas Instruments power products Voltage mode vs. current mode control Differentiating DC/DC converters by analyzing control and compensation schemes: line / load regulation, transient response, BOM, board space, ease-of-use Introduction to the SWIFT software FPGA + CPLD power solutions WIRELESS / CHIPCON Decision criteria when choosing a RF platform Introduction to Texas Instruments wireless products: standardized platforms proprietary platforms ( 2.4 GHz / sub 1 GHz) development tools Antenna design: example for 2.4 GHz questions, discussion Industrial partners: Robert Medioni, François Caloz / Spoerle Electronic, CH-1440 Montagny (VD), Switzerland Phone: +41 24 447 0137, email: RMedioni@spoerle.com, http://www.spoerle.com Language: English. Free s...

  10. Linac4 Technical Design Report

    CERN Document Server

    Arnaudon, L; Baylac, M; Bellodi, G; Body, Y; Borburgh, J; Bourquin, P; Broere, J; Brunner, O; Bruno, L; Carli, C; Caspers, Friedhelm; Cousineau, S M; Cuvet, Y; De Almeida Martins, C; Dobers, T; Fowler, T; Garoby, R; Gerigk, F; Goddard, B; Hanke, K; Hori, M; Jones, M; Kahle, K; Kalbreier, Willi; Kroyer, T; Küchler, D; Lombardi, A M; López-Hernandez, L A; Magistris, M; Martini, M; Maury, S; Page, E; Paoluzzi, M; Pasini, M; Raich, U; Rossi, C; Royer, J P; Sargsyan, E; Serrano, J; Scrivens, R; Silari, M; Timmins, M; Venturini-Delsolaro, W; Vretenar, M; Wegner, R; Weterings, W; Zickler, T

    2006-01-01

    Linac4 is an H- linear accelerator, intended to replace Linac2 as injector to the PS Booster (PSB). By delivering to the PSB a beam at 160 MeV energy, Linac4 will provide the conditions to double the brightness and intensity of the beam from the PSB, thus removing the first bottleneck towards higher brightness for the LHC and simplifying operation. Moreover, this new linac constitutes an essential component of any of the envisaged LHC upgrade scenarios and could open the way to future extensions of the CERN accelerator complex towards higher performance. This Technical Design Report presents a detailed technical overview of the Linac4 design as it stands at end 2006.

  11. Radiation sources and technical services

    International Nuclear Information System (INIS)

    Stonek, K.; Satorie, Z.; Vyskocil, I.

    1981-01-01

    Work is briefly described of the department for sealed sources production of the Institute, including leak testing and surface contamination of sealed sources. The department also provides technical services including the inspections of sealed sources used in medicine and geology and repair of damaged sources. It carries out research of the mechanical and thermal strength of sealed sources and of the possibility of reprocessing used 226 Ra sources. The despatch department is responsible for supplying the entire country with home and imported radionuclides. The department of technical services is responsible for testing imported radionuclides, assembling materials testing, industrial and medical irradiation devices, and for the collection and storage of low-level wastes on a national scale. (M.D.)

  12. Technical note on drainage systems

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby

    This technical note will present simple but widely used methods for the design of drainage systems. The note will primarily deal with surface water (rainwater) which on a satisfactorily way should be transport into the drainage system. Traditional two types of sewer systems exist: A combined system......, where rainwater and sewage is transported in the same pipe, and a separate system where the two types of water are transported in individual pipe. This note will only focus on the separate rain/stormwater system, however, if domestic sewage should be included in the dimensioning procedure, it......’s not major different than described below - just remember to include this contribution for combined systems where the surface water (rain) and sewage are carried in the same pipes in the system and change some of the parameters for failure allowance (this will be elaborated further later on). The technical...

  13. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    KRIPPS, L.J.

    2005-02-18

    This document describes the qualitative evaluation of frequency and consequences for double shell tank (DST) and single shell tank (SST) representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant SSCs and/or TSRS were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support of the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  14. Internal dosimetry technical basis manual

    International Nuclear Information System (INIS)

    1990-01-01

    The internal dosimetry program at the Savannah River Site (SRS) consists of radiation protection programs and activities used to detect and evaluate intakes of radioactive material by radiation workers. Examples of such programs are: air monitoring; surface contamination monitoring; personal contamination surveys; radiobioassay; and dose assessment. The objectives of the internal dosimetry program are to demonstrate that the workplace is under control and that workers are not being exposed to radioactive material, and to detect and assess inadvertent intakes in the workplace. The Savannah River Site Internal Dosimetry Technical Basis Manual (TBM) is intended to provide a technical and philosophical discussion of the radiobioassay and dose assessment aspects of the internal dosimetry program. Detailed information on air, surface, and personal contamination surveillance programs is not given in this manual except for how these programs interface with routine and special bioassay programs

  15. Technical innovation and industrial change

    Energy Technology Data Exchange (ETDEWEB)

    Krupp, H

    1982-10-01

    Technical development is leading by rationalization at economical stagnation to a decrease in the working volume. The economic difficulties are based on the discrepancy between the offer of goods and services as well as the actual demand. The demand of common goods is growing compared to the consumption goods, which will decrease. The therefore necessary structure change requires a high standard of governmental efforts and social consensus.

  16. Information technologies in technical education

    OpenAIRE

    Кравченя, Э. М.

    2013-01-01

    The purpose of researches is working out of the concept of filling of discipline «Information and computer technologies in formation» the first step of higher education entered into curricula was at engineering-pedagogical faculty BNTU. It is shown that as a result of discipline studying there is an expansion of outlook and formation at students of technical college of independent thinking in the field of modern and perspective information technology.

  17. Ideas for clear technical writing

    Science.gov (United States)

    Robinson, B.P.

    1984-01-01

    The three greatest obstacles to clear technical-report writing are probably (1) imprecise words, (2) wordiness, and (3) poorly constructed sentences. Examples of category 1 include abstract words, jargon, and vogue words; of category 2, sentences containing impersonal construction superfluous words; and of category 3, sentences lacking parallel construction and proper order of related words and phrases. These examples and other writing-related subjects are discussed in the report, which contains a cross-referenced index and 24 references.

  18. Fifth technical meeting on quality

    International Nuclear Information System (INIS)

    Girard, A.

    1998-01-01

    This article reports on the 5th Technical Meeting on Quality which was held in San Diego on 20-22 October 1997 and which was attended by representatives of the Home and Joint Central Team and of manufacturers currently involved in the Large R and D projects. The meeting made progress towards the finalization of the ITER Quality Manual document for inclusion in the Final Design Report and the definition of the quality necessary for ITER procurement and construction

  19. Technical center for transportation analyses

    International Nuclear Information System (INIS)

    Foley, J.T.

    1978-01-01

    A description is presented of an information search/retrieval/research activity of Sandia Laboratories which provides technical environmental information which may be used in transportation risk analyses, environmental impact statements, development of design and test criteria for packaging of energy materials, and transportation mode research studies. General activities described are: (1) history of center development; (2) environmental information storage/retrieval system; (3) information searches; (4) data needs identification; and (5) field data acquisition system and applications

  20. Technical vocational education in India

    OpenAIRE

    溝上, 智恵子

    1999-01-01

    In India, several efforts have been made for the development of skilled manpower during the last twenty years since the launch of formal technical vocational education at school. A huge education infrastructure has developed in India. However, 45~50 percent of the population of India is still illiterate. To solve the mismatch between education and employment, a revolution in education is really needed. Additionally, there is a need for a system of National Vocational Qualifications in India a...

  1. Hydrogen Production Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Hydrogen Production Technical Team Roadmap identifies research pathways leading to hydrogen production technologies that produce near-zero net greenhouse gas (GHG) emissions from highly efficient and diverse renewable energy sources. This roadmap focuses on initial development of the technologies, identifies their gaps and barriers, and describes activities by various U.S. Department of Energy (DOE) offices to address the key issues and challenges.

  2. Technical innovation and industrial change

    International Nuclear Information System (INIS)

    Krupp, H.

    1982-01-01

    Technical development is leading by rationalization at economical stagnation to a decrease in the working volume. The economical difficulties are based on the discrepancy between the offer of goods and services as well as the actual demand. The demand of common goods is growing compared to the consumption goods, which will decrease. The therefore necessary structure change requires a high standard of governmental efforts and social consensus. (orig.) [de

  3. Parliamentarian sovereignty and technical development

    International Nuclear Information System (INIS)

    Dreier, H.; Hofmann, J.

    1986-01-01

    The title indicates the points of main emphasis of the contributions, and points to the programme embodied in the volume. The question is - given the tremendous and ever increasing amount of secondary problems associated with a heated technology development - whether the 'sovereign' state is at all capable of controlling, piloting and fostering technic-scientific processes. The first part ('sovereignty and parliamentarian legislator state') concentrates on the history of notions and ideas in the concept of the sovereign, modern state, and on the constitutional law in force (Dreier, Frohn); the current efficiency of parliament as an organ of control in the process of legislation is investigated (Schulze-Fielitz). The central concern of part 2 ('environmental law and technical development') are topical questions of environmental law (Hofmann, Luebbe-Wolff). Besides the analysis of dogmatic problems of a special administrative law, the major issue is whether and in how far - given modern large-scale technologies - law can adequately govern technique (Schmidt). By analyzing the relationship between technical development and possibilities for guidance by a parliamentarian constitutional state, the articles deal with a central point of intersection between state and administrative law. (orig./HP) [de

  4. Who Recognises Technical Standards in TTIP?

    NARCIS (Netherlands)

    K.P. Purnhagen (Kai)

    2017-01-01

    textabstractCurrent political discussions on the relationship of technical standards to the Transatlantic, Trade and Investment Partnership (TTIP) concern the question whether TTIP can provide a transatlantic level playing field for technical standards, and whether this will negatively affect

  5. Objective assessment of technical skills in surgery

    OpenAIRE

    Moorthy, Krishna; Munz, Yaron; Sarker, Sudip K; Darzi, Ara

    2003-01-01

    In the past few years, considerable developments have been made in the objective assessment of technical proficiency of surgeons. Technical skills should be assessed during training, and various methods have been developed for this purpose

  6. Summary of Sandia Laboratories technical capabilities

    International Nuclear Information System (INIS)

    1977-05-01

    The technical capabilities of Sandia Laboratories are detailed in a series of companion reports. In this summary the use of the capabilities in technical programs is outlined and the capabilities are summarized. 25 figures, 3 tables

  7. Works Technical Department progress report, March 1961

    Energy Technology Data Exchange (ETDEWEB)

    None

    1961-04-19

    This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  8. Final Technical Report: Development of Post-Installation Monitoring Capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Polagye, Brian [University of Washington

    2014-03-31

    The development of approaches to harness marine and hydrokinetic energy at large-scale is predicated on the compatibility of these generation technologies with the marine environment. At present, aspects of this compatibility are uncertain. Demonstration projects provide an opportunity to address these uncertainties in a way that moves the entire industry forward. However, the monitoring capabilities to realize these advances are often under-developed in comparison to the marine and hydrokinetic energy technologies being studied. Public Utility District No. 1 of Snohomish County has proposed to deploy two 6-meter diameter tidal turbines manufactured by OpenHydro in northern Admiralty Inlet, Puget Sound, Washington. The goal of this deployment is to provide information about the environmental, technical, and economic performance of such turbines that can advance the development of larger-scale tidal energy projects, both in the United States and internationally. The objective of this particular project was to develop environmental monitoring plans in collaboration with resource agencies, while simultaneously advancing the capabilities of monitoring technologies to the point that they could be realistically implemented as part of these plans. In this, the District was joined by researchers at the Northwest National Marine Renewable Energy Center at the University of Washington, Sea Mammal Research Unit, LLC, H.T. Harvey & Associates, and Pacific Northwest National Laboratory. Over a two year period, the project team successfully developed four environmental monitoring and mitigation plans that were adopted as a condition of the operating license for the demonstration project that issued by the Federal Energy Regulatory Commission in March 2014. These plans address nearturbine interactions with marine animals, the sound produced by the turbines, marine mammal behavioral changes associated with the turbines, and changes to benthic habitat associated with colonization

  9. Technical specification improvement through safety margin considerations

    International Nuclear Information System (INIS)

    Howard, R.C.; Jansen, R.L.

    1986-01-01

    Westinghouse has developed an approach for utilizing safety analysis margin considerations to improve plant operability through technical specification revision. This approach relies on the identification and use of parameter interrelations and sensitivities to identify acceptable operating envelopes. This paper summarizes technical specification activities to date and presents the use of safety margin considerations as another viable method to obtain technical specification improvement

  10. ITER technical advisory committee meeting at Garching

    International Nuclear Information System (INIS)

    Fujiwara, M.

    1999-01-01

    The ITER Technical Advisory Committee meeting took place on 24-27 February at the Garching Joint Work Site. According to the discussions at the ITER meeting in Yokohama in October 1998, the Technical Advisory Committee was requested to conduct a thorough review of the document 'Options for the reduced technical objectives / reduced cost ITER'

  11. 49 CFR 845.22 - Technical panel.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Technical panel. 845.22 Section 845.22... Technical panel. The Director, Bureau of Accident Investigation, or the Director, Bureau of Field Operations, shall designate members of the Board's technical staff to participate in the hearing and initially...

  12. 48 CFR 12.211 - Technical data.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Technical data. 12.211... ACQUISITION OF COMMERCIAL ITEMS Special Requirements for the Acquisition of Commercial Items 12.211 Technical data. Except as provided by agency-specific statutes, the Government shall acquire only the technical...

  13. 32 CFR 701.38 - Technical data.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Technical data. 701.38 Section 701.38 National... DOCUMENTS AFFECTING THE PUBLIC FOIA Definitions and Terms § 701.38 Technical data. Recorded information, regardless of form or method of the recording, of a scientific or technical nature (including computer...

  14. 48 CFR 212.211 - Technical data.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

  15. 15 CFR 911.8 - Technical requirements.

    Science.gov (United States)

    2010-01-01

    ... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Technical requirements. 911.8 Section...

  16. Why and How to Advance Technical Copywriting.

    Science.gov (United States)

    Henson, Leigh

    1996-01-01

    States that promotional writing for industrial/high-tech products, or technical copywriting, is gaining more attention in technical communication, although it is neglected in higher education. Testifies to the significance of technical copywriting. Suggests that dialogical audience analysis and an emphasis on rational appeal will contribute to…

  17. 25 CFR 41.10 - Technical assistance.

    Science.gov (United States)

    2010-04-01

    ... Community College's request in writing. In any case, where the type and source of technical assistance is... for technical assistance under this section shall be made in writing and sent to the applicant within... 25 Indians 1 2010-04-01 2010-04-01 false Technical assistance. 41.10 Section 41.10 Indians BUREAU...

  18. Getting Personal: Individuality, Innovation, and Technical Communication.

    Science.gov (United States)

    Steiner, Carol J.

    1999-01-01

    Suggests that effective communication between technical and nontechnical people is difficult because technical communication lacks a personal dimension: technical people give up their identity to be considered competent. Argues that a different approach to communication education for scientists, engineers, and technologists is required to equip…

  19. Head Start Impact Study. Technical Report

    Science.gov (United States)

    Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

    2010-01-01

    This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

  20. 7 CFR 3430.55 - Technical reporting.

    Science.gov (United States)

    2010-01-01

    ... required to submit other technical reports or submit the CRIS reports more frequently than annually... 7 Agriculture 15 2010-01-01 2010-01-01 false Technical reporting. 3430.55 Section 3430.55... ASSISTANCE PROGRAMS-GENERAL AWARD ADMINISTRATIVE PROVISIONS Post-Award and Closeout § 3430.55 Technical...

  1. MedlinePlus Connect: Technical Information

    Science.gov (United States)

    ... MedlinePlus Connect → Technical Information URL of this page: https://medlineplus.gov/connect/technical.html MedlinePlus Connect: Technical ... will change.) Old URLs New URLs Web Application https://apps.nlm.nih.gov/medlineplus/services/mpconnect.cfm? ...

  2. Economic filters for evaluating porphyry copper deposit resource assessments using grade-tonnage deposit models, with examples from the U.S. Geological Survey global mineral resource assessment: Chapter H in Global mineral resource assessment

    Science.gov (United States)

    Robinson, Gilpin R.; Menzie, W. David

    2012-01-01

    An analysis of the amount and location of undiscovered mineral resources that are likely to be economically recoverable is important for assessing the long-term adequacy and availability of mineral supplies. This requires an economic evaluation of estimates of undiscovered resources generated by traditional resource assessments (Singer and Menzie, 2010). In this study, simplified engineering cost models were used to estimate the economic fraction of resources contained in undiscovered porphyry copper deposits, predicted in a global assessment of copper resources. The cost models of Camm (1991) were updated with a cost index to reflect increases in mining and milling costs since 1989. The updated cost models were used to perform an economic analysis of undiscovered resources estimated in porphyry copper deposits in six tracts located in North America. The assessment estimated undiscovered porphyry copper deposits within 1 kilometer of the land surface in three depth intervals.

  3. Legitimizing Technical Communication in English Departments: Carolyn Miller's "Humanistic Rationale for Technical Writing"

    Science.gov (United States)

    Moore, Patrick

    2006-01-01

    Carolyn Miller's oft-cited "Humanistic Rationale for Technical Writing," published in 1979, tries to give technical communication faculty more cultural capital in English departments controlled by literature professors. Miller replaces a positivistic emphasis in technical communication pedagogy with rhetoric. She shows how technical knowledge is…

  4. Subsurface Fire Hazards Technical Report

    International Nuclear Information System (INIS)

    Logan, R.C.

    1999-01-01

    The results from this report are preliminary and cannot be used as input into documents supporting procurement, fabrication, or construction. This technical report identifies fire hazards and proposes their mitigation for the subsurface repository fire protection system. The proposed mitigation establishes the minimum level of fire protection to meet NRC regulations, DOE fire protection orders, that ensure fire containment, adequate life safety provisions, and minimize property loss. Equipment requiring automatic fire suppression systems is identified. The subsurface fire hazards that are identified can be adequately mitigated

  5. Intrinsic stability of technical superconductors

    International Nuclear Information System (INIS)

    Veringa, H.J.

    1981-10-01

    For the operation of technical superconductors under high current density conditions, the superconducting wires composing high current cables should be intrinsically stabilized. In this report the various important stability criteria are derived and investigated on their validity. An experimental set up is made to check the occurrence of magnetic instabilities if the different applicable criteria are violated. It is found that the observed instabilities can be predicted on the basis of the model given in this report. Production of high current cables based upon composites made by the ECN technique seems to be possible. (Auth.)

  6. Professional Excellence Beyond Technical Competence

    CERN Document Server

    Rossiter, Alan P

    2008-01-01

    The training path for engineers focuses intensely on scientific and technical knowledge. Yet, our professional and personal satisfaction and success also depend on other traits that make us more effective and productive. In this thought-provoking book, Alan Rossiter provides practical guidance in developing the skills to become more effective in your work, while also balancing your life. It is invaluable reading for graduating college students and young professionals as well as seasoned practitioners who find that work is becoming all-consuming.

  7. PVWatts Version 1 Technical Reference

    Energy Technology Data Exchange (ETDEWEB)

    Dobos, A. P.

    2013-10-01

    The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

  8. Technical approach to aging management

    International Nuclear Information System (INIS)

    Vora, J.P.; Johnson, A.B. Jr.; Allen, R.P.

    1992-10-01

    Systematic and effective control of age-related degradation of safety-related components, systems, and structures in nuclear power plants (NPPs) is an important challenge to plant operators. Several data bases, available to provide guidance on aging management, are summarized. However, the ultimate consideration is: How effectively is aging management being implemented at individual plants? Illustrated here is a specific strategy that served to develop the technical data base for the Nuclear Plant Aging Research Program. The strategy is comprehensive, systematic, and adaptable. Effective aging management at NPPs could be facilitated by a parallel strategy. The elements of a strategy are suggested

  9. Progress report : Technical Physics Division

    International Nuclear Information System (INIS)

    Gopalaraman, C.P.; Deshpande, R.Y.

    1978-01-01

    The research and development work carried out in the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, is reported. Some of the achievements are: (1) fabrication of mass spectrometers for heavy water analysis and lithium 6/7 isotope ratio measurement, (2) fabrication of electronic components for mass spectrometers, (3) growing of sodium iodide crystals for radiation detectors, (4) development of sandwich detectors comprising of NaI(Tl) and CaI(Na), (5) fabrication of mass spectrometer type leak detectors and (6) fabrication of the high vacuum components of the vacuum system of the variable energy cyclotron based at Calcutta. (M.G.B.)

  10. Technical presentation: Next Generation Oscilloscopes

    CERN Multimedia

    PH Department

    2011-01-01

      Rohde & Schwarz "Next Generation Oscilloscopes" - Introduction and Presentation Agenda: Wednesday 23 March  -  09:30 to 11:30 (open end) Bldg. 13-2-005 Language: English 09.30 Presentation "Next Generation Oscilloscopes" from Rohde & Schwarz RTO / RTM in theory and practice Gerard Walker 10.15 Technical design details from R&D Dr. Markus Freidhof 10.45 Scope and Probe Roadmap (confidential) Guido Schulze 11.00 Open Discussion Feedback, first impression, wishes, needs and requirements from CERN All 11.30 Expert Talks, Hands on All Mr. Dr. Markus Freidhof, Head of R&D Oscilloscopes, Rohde & Schwarz, Germany; Mr. Guido Schulze, ...

  11. Technical report on the accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Bex, L [ed.

    1996-12-31

    GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d`Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d`Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.). 48 refs.

  12. Belle II Technical Design Report

    CERN Document Server

    Abe, T; Adamczyk, K; Ahn, S; Aihara, H; Akai, K; Aloi, M; Andricek, L; Aoki, K; Arai, Y; Arefiev, A; Arinstein, K; Arita, Y; Asner, D M; Aulchenko, V; Aushev, T; Aziz, T; Bakich, A M; Balagura, V; Ban, Y; Barberio, E; Barvich, T; Belous, K; Bergauer, T; Bhardwaj, V; Bhuyan, B; Blyth, S; Bondar, A; Bonvicini, G; Bozek, A; Bracko, M; Brodzicka, J; Brovchenko, O; Browder, T E; Cao, G; Chang, M -C; Chang, P; Chao, Y; Chekelian, V; Chen, A; Chen, K -F; Chen, P; Cheon, B G; Chiang, C -C; Chistov, R; Cho, K; Choi, S -K; Chung, K; Comerma, A; Cooney, M; Cowley, D E; Critchlow, T; Dalseno, J; Danilov, M; Dieguez, A; Dierlamm, A; Dillon, M; Dingfelder, J; Dolenec, R; Dolezal, Z; Drasal, Z; Drutskoy, A; Dungel, W; Dutta, D; Eidelman, S; Enomoto, A; Epifanov, D; Esen, S; Fast, J E; Feindt, M; Garcia, M Fernandez; Fifield, T; Fischer, P; Flanagan, J; Fourletov, S; Fourletova, J; Freixas, L; Frey, A; Friedl, M; Fruehwirth, R; Fujii, H; Fujikawa, M; Fukuma, Y; Funakoshi, Y; Furukawa, K; Fuster, J; Gabyshev, N; Cueto, A Gaspar de Valenzuela; Garmash, A; Garrido, L; Geisler, Ch; Gfall, I; Goh, Y M; Golob, B; Gorton, I; Grzymkowski, R; Guo, H; Ha, H; Haba, J; Hara, K; Hara, T; Haruyama, T; Hayasaka, K; Hayashi, K; Hayashii, H; Heck, M; Heindl, S; Heller, C; Hemperek, T; Higuchi, T; Horii, Y; Hou, W -S; Hsiung, Y B; Huang, C -H; Hwang, S; Hyun, H J; Igarashi, Y; Iglesias, C; Iida, Y; Iijima, T; Imamura, M; Inami, K; Irmler, C; Ishizuka, M; Itagaki, K; Itoh, R; Iwabuchi, M; Iwai, G; Iwai, M; Iwasaki, M; Iwasaki, M; Iwasaki, Y; Iwashita, T; Iwata, S; Jang, H; Ji, X; Jinno, T; Jones, M; Julius, T; Kageyama, T; Kah, D H; Kakuno, H; Kamitani, T; Kanazawa, K; Kapusta, P; Kataoka, S U; Katayama, N; Kawai, M; Kawai, Y; Kawasaki, T; Kennedy, J; Kichimi, H; Kikuchi, M; Kiesling, C; Kim, B K; Kim, G N; Kim, H J; Kim, H O; Kim, J -B; Kim, J H; Kim, M J; Kim, S K; Kim, K T; Kim, T Y; Kinoshita, K; Kishi, K; Kisielewski, B; van Dam, K Kleese; Knopf, J; Ko, B R; Koch, M; Kodys, P; Koffmane, C; Koga, Y; Kohriki, T; Koike, S; Koiso, H; Kondo, Y; Korpar, S; Kouzes, R T; Kreidl, Ch; Kreps, M; Krizan, P; Krokovny, P; Krueger, H; Kruth, A; Kuhn, W; Kuhr, T; Kumar, R; Kumita, T; Kupper, S; Kuzmin, A; Kvasnicka, P; Kwon, Y -J; Lacasta, C; Lange, J S; Lee, I -S; Lee, M J; Lee, M W; Lee, S -H; Lemarenko, M; Li, J; Li, W D; Li, Y; Libby, J; Limosani, A; Liu, C; Liu, H; Liu, Y; Liu, Z; Liventsev, D; Virto, A Lopez; Makida, Y; Mao, Z P; Marinas, C; Masuzawa, M; Matvienko, D; Mitaroff, W; Miyabayashi, K; Miyata, H; Miyazaki, Y; Miyoshi, T; Mizuk, R; Mohanty, G B; Mohapatra, D; Moll, A; Mori, T; Morita, A; Morita, Y; Moser, H -G; Martin, D Moya; Mueller, T; Muenchow, D; Murakami, J; Myung, S S; Nagamine, T; Nakamura, I; Nakamura, T T; Nakano, E; Nakano, H; Nakao, M; Nakazawa, H; Nam, S -H; Natkaniec, Z; Nedelkovska, E; Negishi, K; Neubauer, S; Ng, C; Ninkovic, J; Nishida, S; Nishimura, K; Novikov, E; Nozaki, T; Ogawa, S; Ohmi, K; Ohnishi, Y; Ohshima, T; Ohuchi, N; Oide, K; Olsen, S L; Ono, M; Ono, Y; Onuki, Y; Ostrowicz, W; Ozaki, H; Pakhlov, P; Pakhlova, G; Palka, H; Park, H; Park, H K; Peak, L S; Peng, T; Peric, I; Pernicka, M; Pestotnik, R; Petric, M; Piilonen, L E; Poluektov, A; Prim, M; Prothmann, K; Regimbal, K; Reisert, B; Richter, R H; Riera-Babures, J; Ritter, A; Ritter, A; Ritter, M; Roehrken, M; Rorie, J; Rosen, M; Rozanska, M; Ruckman, L; Rummel, S; Rusinov, V; Russell, R M; Ryu, S; Sahoo, H; Sakai, K; Sakai, Y; Santelj, L; Sasaki, T; Sato, N; Sato, Y; Scheirich, J; Schieck, J; Schwanda, C; Schwartz, A J; Schwenker, B; Seljak, A; Senyo, K; Seon, O -S; Sevior, M E; Shapkin, M; Shebalin, V; Shen, C P; Shibuya, H; Shiizuka, S; Shiu, J -G; Shwartz, B; Simon, F; Simonis, H J; Singh, J B; Sinha, R; Sitarz, M; Smerkol, P; Sokolov, A; Solovieva, E; Stanic, S; Staric, M; Stypula, J; Suetsugu, Y; Sugihara, S; Sugimura, T; Sumisawa, K; Sumiyoshi, T; Suzuki, K; Suzuki, S Y; Takagaki, H; Takasaki, F; Takeichi, H; Takubo, Y; Tanaka, M; Tanaka, S; Taniguchi, N; Tarkovsky, E; Tatishvili, G; Tawada, M; Taylor, G N; Teramoto, Y; Tikhomirov, I; Trabelsi, K; Tsuboyama, T; Tsunada, K; Tu, Y -C; Uchida, T; Uehara, S; Ueno, K; Uglov, T; Unno, Y; Uno, S; Urquijo, P; Ushiroda, Y; Usov, Y; Vahsen, S; Valentan, M; Vanhoefer, P; Varner, G; Varvell, K E; Vazquez, P; Vila, I; Vilella, E; Vinokurova, A; Visniakov, J; Vos, M; Wang, C H; Wang, J; Wang, M -Z; Wang, P; Wassatch, A; Watanabe, M; Watase, Y; Weiler, T; Wermes, N; Wescott, R E; White, E; Wicht, J; Widhalm, L; Williams, K M; Won, E; Xu, H; Yabsley, B D; Yamamoto, H; Yamaoka, H; Yamaoka, Y; Yamauchi, M; Yin, Y; Yoon, H; Yu, J; Yuan, C Z; Yusa, Y; Zander, D; Zdybal, M; Zhang, Z P; Zhao, J; Zhao, L; Zhao, Z; Zhilich, V; Zhou, P; Zhulanov, V; Zivko, T; Zupanc, A; Zyukova, O

    2010-01-01

    The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been proposed. A new international collaboration Belle-II, is being formed. The Technical Design Report presents physics motivation, basic methods of the accelerator upgrade, as well as key improvements of the detector.

  13. Technical report on the accelerators

    International Nuclear Information System (INIS)

    Bex, L.

    1995-01-01

    GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d'Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d'Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.)

  14. Conversion of NEK standard technical specifications into improved technical specifications

    International Nuclear Information System (INIS)

    Glaser, B.

    2003-01-01

    Neck is currently using a standard format of operation's Technical Specifications - STS (based on NUREG-0452), which are planned to be converted into Improved Technical Specifications - ITS (based on NUREG-1431). To facilitate the development of individual ITS, each reactor vendor owners group (OG) and the NRC staff developed improved standard TS (ISTS). For Westinghouse plants, the ISTS are published as NUREG-1431, and this document is going to be the basis for the new NEK ITS. It has been recognized that nuclear safety in all plants would benefit from improvement and standardization of ITS, so this was also addressed and recognized by the NRC. There are several plants around Europe and US, which have replaced the format into ITS which brings a lot of improvements and practical value in operations. The main objective of conversion is to completely rewrite, reformat, and streamline the existing STS. Emphasis is placed on human factors principles to improve clarity and understanding. The Bases section will be significantly expanded to clarify and better explain the purpose and foundation of each specification. There might be some proposed changes to the existing STS that deviated from the ITS in NUREG-1431 and constitute a relaxation of the existing STS. Each of these additional proposed changes will be described and evaluated in amendment application and justified on a case-by-case basis. Since the NEK is going to operate for more than 20 year without considering life extension, such conversion will be beneficial for operation personnel as well as regulation, surveillance and focus on operation's safety. At the present, only preliminary plan of STS conversion exists, showing the time frame of approximately 2 years of conversion process and numerous tasks that need to be performed. The plan is to begin with process in year 2004 and finish project in 2006, which means use of new ITS in main control room in year 2007. Beside the main process of conversion, there are

  15. Technical Problems of Residential Construction

    Science.gov (United States)

    Nowogońska, Beata; Cibis, Jerzy

    2017-10-01

    Beauty, utility, durability - these are the features of good architecture and should also be the distinguishing qualities of every residential building. But do beauty and utility remain along with the passing of time? Performance characteristics are an indicator of both, the technical as well as aesthetic state of buildings. Aesthetic needs are in disagreement with the merciless aging process. The beauty of a city is formed not only by the original forms of new residential buildings, but also by existing tenement housing; thus preserving their aesthetics becomes a necessity. Time is continuously passing and along with it, aging intensifies. The aging process is a natural phenomenon for every material. The life expectancy of building materials is also limited. Along with the passing of time, the technical state of residential buildings continuously deteriorates. With the passing of time, the aesthetic values and preferences of users of flats change and the usability of the building decreases. The permanence of buildings, including residential buildings, is shaped not only by the forces of nature but also by activities of humans. A long lifespan is ensured by carrying out ongoing, systematic renovation-repair works. It is thanks to them that buildings derived from past centuries are still being used, and their market attractiveness is not decreasing.

  16. Succession planning for technical experts

    International Nuclear Information System (INIS)

    Kirk, Bernadette Lugue; Cain, Ronald A.; Dewji, Shaheen A.; Agreda, Carla L.

    2017-01-01

    This report describes a methodology for identifying, evaluating, and mitigating the loss of key technical skills at nuclear operations facilities. The methodology can be adapted for application within regulatory authorities and research and development organizations, and can be directly applied by international engagement partners of the Department of Energy’s National Nuclear Security Administration (NNSA). The resultant product will be of direct benefit to two types of NNSA missions: (1) domestic human capital development programs tasked to provide focused technical expertise to succeed an aging nuclear operations workforce, and (2) international safeguards programs charged with maintaining operational safeguards for developing/existing nuclear power program in nations where minimal available resources must be used effectively. This report considers succession planning and the critical skills necessary to meet an institution’s goals and mission. Closely tied to succession planning are knowledge management and mentorship. In considering succession planning, critical skill sets are identified and are greatly dependent on the subject matter expert in question. This report also provides examples of critical skills that are job specific.

  17. Productivity Measurement Of Technical Institute

    Directory of Open Access Journals (Sweden)

    Miss.Pooja Yadav

    2015-05-01

    Full Text Available Abstract The increasing concern over globalization between other things has made the achievement of lifetime skills vital for all classes of people. Achievement of such skills can be developed from technical education programs in the advance of any nation. Skill gaining provides knowledge and inculcates the approaches that are essential for arrival and progress into an occupation. When skills are developed in any occupation it will provide and improve the standard of living with the cover beside poverty thereby behind national development. This paper observes sampling distribution and moving average concept that how technical education can generate the required skills the significance of skill acquisition its roles benefits and sustainability in national development. It also mentions among others that government should look into and improve productivity that can encourage skill achievement for the youths. The solutions are divided the sampling box into few group before stacking up workstation and use table and some other wood product. Cost reduction for each solution was intended and the solution with highest cost decrease is chosen to increase the productivity of the college.

  18. Small wind turbines - Technical sheet

    International Nuclear Information System (INIS)

    2015-02-01

    This publication first proposes an overview of the technical context of small wind turbines (from less than 1 kW to 36 kW). It discusses issues related to mast height, indicates the various technologies in terms of machine geometry (vertical or horizontal axis), of mast and foundations, of mechanism of orientation with respect to the wind. It also outlines that power curves are not always reliable due to a lack of maturity of techniques and technologies. Other issues are discussed: wind characteristics, and the assessment of the national potential source. The next parts address the regulatory and economic context, environmental impacts (limited impact on landscape, noise), propose an overview of actors and market (supply and demand of small wind turbines in the USA and in France, actors involved in the chain value in France), and give some recommendations for the development of small wind turbines in France. The last part proposes a technical focus on self-consumption by professional in rural areas (production and consumption in farms)

  19. CERN Technical Training: Signal Processor

    CERN Multimedia

    HR Department

    2009-01-01

    A new training is going to be held at CERN on the ADSP SHARC Family. The "System Development and Programming with the Analog Devices’ SHARC Family" course is a 3.5-day hands-on training on Analog Devices SHARC DSPs, focusing on the latest ‘368/9 and 37x families. General DSP architecture, peripherals available, booting up process and DSP code development will be covered. Hardware tools, debugging and hardware design guidelines will be introduced as well. The course id designed for System Designers needing to make informed decisions on design tradeoffs, Hardware Designers needing to develop external interfaces, and Code Developers needing to know how to get the highest performance from their algorithms. The course will take place, in English, from 31 March to 4 April in the CERN Technical Training Center. Few places are still available. Registrations are opened on the Technical Training page. More information on our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your que...

  20. Succession planning for technical experts

    Energy Technology Data Exchange (ETDEWEB)

    Kirk, Bernadette Lugue [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Cain, Ronald A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dewji, Shaheen A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Agreda, Carla L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-07-01

    This report describes a methodology for identifying, evaluating, and mitigating the loss of key technical skills at nuclear operations facilities. The methodology can be adapted for application within regulatory authorities and research and development organizations, and can be directly applied by international engagement partners of the Department of Energy’s National Nuclear Security Administration (NNSA). The resultant product will be of direct benefit to two types of NNSA missions: (1) domestic human capital development programs tasked to provide focused technical expertise to succeed an aging nuclear operations workforce, and (2) international safeguards programs charged with maintaining operational safeguards for developing/existing nuclear power program in nations where minimal available resources must be used effectively. This report considers succession planning and the critical skills necessary to meet an institution’s goals and mission. Closely tied to succession planning are knowledge management and mentorship. In considering succession planning, critical skill sets are identified and are greatly dependent on the subject matter expert in question. This report also provides examples of critical skills that are job specific.

  1. Technical approach to groundwater restoration

    International Nuclear Information System (INIS)

    1993-01-01

    The Technical Approach to Groundwater Restoration (TAGR) provides general technical guidance to implement the groundwater restoration phase of the Uranium Mill Tailings Remedial Action (UMTRA) Project. The TAGR includes a brief overview of the surface remediation and groundwater restoration phases of the UMTRA Project and describes the regulatory requirements, the National Environmental Policy Act (NEPA) process, and regulatory compliance. A section on program strategy discusses program optimization, the role of risk assessment, the observational approach, strategies for meeting groundwater cleanup standards, and remedial action decision-making. A section on data requirements for groundwater restoration evaluates the data quality objectives (DQO) and minimum data required to implement the options and comply with the standards. A section on sits implementation explores the development of a conceptual site model, approaches to site characterization, development of remedial action alternatives, selection of the groundwater restoration method, and remedial design and implementation in the context of site-specific documentation in the site observational work plan (SOWP) and the remedial action plan (RAP). Finally, the TAGR elaborates on groundwater monitoring necessary to evaluate compliance with the groundwater cleanup standards and protection of human health and the environment, and outlines licensing procedures

  2. Technical Submission Form: Technical Specification of a Wave Energy Farm.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Jesse D.; Kim Nielsen; Ben Kennedy; Bull, Diana L; Costello, Ronan Patrick; Jochem Weber

    2017-04-01

    The Wave - SPARC project developed the Technology Performance Level (TPL) assessment procedure based on a rigorous Systems Engineering exercise. The TPL assessment allows a whole system evaluation of Wave Energy Conversion Technology by measuring it against the requirements determined through the Systems Engineering exercise. The TPL assessment is intended to be useful in technology evaluation; in technology innovation; in allocation of public or priva te investment, and; in making equipment purchasing decisions. This Technical Submission Form (TSF) serves the purpose of collecting relevant and complete information, in a technology agnostic way, to allow TPL assessment s to be made by third party assessor s. The intended usage of this document is that the organization or people that are performing the role of developers or promoters of a particular technology will use this form to provide the information necessary for the organization or people who are perf orming the assessor role to use the TPL assessment.

  3. How to be an Effective Technical Writer?

    Directory of Open Access Journals (Sweden)

    M Solaiman Ali

    2012-07-01

    Full Text Available Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations. Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical writing for engineers stresses that a successful engineering career requires strong writing skills. Part 2 (How to write the major sections or elements of a report describes the techniques of writing the abstract, introduction, literature review, procedure/methods & materials, results, discussion, conclusion, and recommendations. Part 3 (Special features of technical writing brings into focus some of the special features of technical writing such as tables & graphs in the text, graphics in instructions, team writing, ethics (plagiarism, document sources, three citation styles and IEEE reference style. Part 4 (Technical usage deals with writing abbreviations, initialisms and acronyms, numbers, units of measurement, and equations.Part 5 (Technical style highlights the imperative writing style and other features of technical writing such as the use of active and passive voices, plain vs. complex syntax, avoiding redundant or superfluous expressions, and vague generalities, using words or expressions with visual impact, the past tense to describe experimental work, the present tense to describe hypotheses, principles, theories and truths, and breaking up the text of the report into short sections. Part 6 (Document specifications emphasizes the technical writer’s need to conform to such document specifications as word count, format, font, number of words per line of text imposed. Part 7 (Reader-friendly technical writing suggests choosing the varied writing modes

  4. Marketing information: The technical report as product

    Science.gov (United States)

    Stoher, F. F.; Pinelli, T. E.

    1981-01-01

    Technical reports constitute a product, the primary means for communicating the results of research to the user. The Langley scientific and technical information (STI) review and evaluation project undertook a review of the technical report as an effective product for information communication. Style manuals describing theory and practice in technical report preparation; publication manuals covering such factors as design, layout, and type style; and copies of technical reports were obtained from industrial, academic, governmental, and research organizations. Based on an analysis of this material, criteria will be established for the report components, for the relationship of the components within the report context, and for the overall report organization. The criteria will be used as bench marks and compared with the publication standards currently used to prepare NASA technical reports.

  5. Technical tasks in superconducting cavities

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Kenji [High Energy Accelerator Research Organization, Tsukuba, Ibaraki (Japan)

    1997-11-01

    The feature of superconducting rf cavities is an extremely small surface resistance on the wall. It brings a large energy saving in the operation, even those are cooled with liquid helium. That also makes possible to operate themselves in a higher field gradient comparing to normal conducting cavities, and brings to make accelerators compact. These merits are very important for the future accelerator engineering which is planed at JAERI for the neutron material science and nuclear waste transmutation. This machine is a high intensity proton linac and uses sc cavities in the medium and high {beta} sections. In this paper, starting R and D of proton superconducting cavities, several important technical points which come from the small surface resistance of sc cavities, are present to succeed it and also differences between the medium and high - {beta} structures are discussed. (author)

  6. Chernobyl - a Canadian technical perspective

    International Nuclear Information System (INIS)

    Howieson, J.Q.; Snell, V.G.

    1987-01-01

    In this report we present the design review done to date in Canada by AECL. From the Canadian point of view it covers: 1) relevant information on the Chernobyl design and the accident, both as presented by the Soviets at the Post-Accident Review Meeting (PARM) held in Vienna from August 25-29, 1986, and as deduced from publicly available Soviet documentation; and 2) details of AECL's technical review of the CANDU PHWR (Pressurized Heavy Water Reactor) against the background of the Chernobyl accident, and implications of the Chernobyl accident. Reviews of operational aspects are underway by the Canadian electrical utilities and a review by the Canadian regulatory agency (the Atomic Energy Control Board) is near completion

  7. Crew Transportation Technical Management Processes

    Science.gov (United States)

    Mckinnie, John M. (Compiler); Lueders, Kathryn L. (Compiler)

    2013-01-01

    Under the guidance of processes provided by Crew Transportation Plan (CCT-PLN-1100), this document, with its sister documents, International Space Station (ISS) Crew Transportation and Services Requirements Document (CCT-REQ-1130), Crew Transportation Technical Standards and Design Evaluation Criteria (CCT-STD-1140), Crew Transportation Operations Standards (CCT STD-1150), and ISS to Commercial Orbital Transportation Services Interface Requirements Document (SSP 50808), provides the basis for a National Aeronautics and Space Administration (NASA) certification for services to the ISS for the Commercial Provider. When NASA Crew Transportation System (CTS) certification is achieved for ISS transportation, the Commercial Provider will be eligible to provide services to and from the ISS during the services phase.

  8. The International Technical Safety Forum

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    The International Technical Safety Forum is a meeting of safety experts from several physics labs in Europe and the US. Since 1998 participants have been meeting every couple of years to discuss common challenges in safety matters. The Forum helps them define best practices and learn from the important lessons learned by others.   The Forum's participants in front of building 40. This year, the meeting took place at CERN from 12 to 16 April. “This year's meeting covered subjects ranging from communication and training in matters of safety, to cryogenic safety, emergency preparedness and risk analysis”, explains Ralf Trant, head of the CERN Safety Commission and organiser of this year’s Forum. Radiation protection issues are not discussed at the meeting since they involve different expertise. The goal of the Forum is to allow participants to share experience, learn lessons and acquire specific knowledge in a very open way. Round-table discussions, dedicated time for ...

  9. [Ageing and work: technical standards].

    Science.gov (United States)

    De Vito, G; Riva, M A; Meroni, R; Cesana, G C

    2010-01-01

    Over the last few years, studies on the relationship between ageing and work have attracted growing interest due to the increased probability among workers of developing major health problems as a consequence of ageing of the working population. Negative outcomes for health are possible when an age-related imbalance appears between physical workload and physical work capacity. Interventions based on workload reductions should help to keep workers on the job for as long as allowed by law. Reference masses by age and sex are suggested by the technical standards of the ISO 11228 series, which are also quoted by Italian law D.Lgs. 81/2008, and EN 1005 series, which recommend limits valid also for manual material handling, and pushing and pulling. Decreasing low back pain prevalence or recurrence, in an ageing population with high prevalence of back disorders, could be more effective than many other approaches to enhance workers' quality of life and consequently maintain and improve workers' performance.

  10. Computers in technical information transfer

    Energy Technology Data Exchange (ETDEWEB)

    Price, C.E.

    1978-01-01

    The use of computers in transferring scientific and technical information from its creation to its use is surveyed. The traditional publication and distribution processes for S and T literature in past years have been the vehicle for transfer, but computers have altered the process in phenomenal ways. Computers are used in literature publication through text editing and photocomposition applications. Abstracting and indexing services use computers for preparing their products, but the machine-readable document descriptions created for this purpose are input to a rapidly growing computerized information retrieval service industry. Computer use is making many traditional processes passe, and may eventually lead to a largely ''paperless'' information utility.

  11. Superphenix: technical and scientific achievements

    International Nuclear Information System (INIS)

    Guidez, Joel; Prele, Gerard

    2016-04-01

    In this book, the authors propose a synthesis of technical and scientific achievements related to the design, fabrication and eleven-year operation of Superphenix, the most powerful fast breeder reactor ever built and operated. They had the opportunity to use various and important archives maintained by the different involved institutions, actors and companies, such as the CEA with its MADONA database, AREVA and EDF. They address all the different fields: construction, chemistry, exploitation, handling, small and large components, materials, fuel manufacturing, environmental assessment, thermal hydraulics, the sodium-water reaction, sodium fires, the release of residual power, in-service inspection, and dismantling operations. Moreover, a chapter addresses design studies for Superphenix 2 and for the European Fast Reactor (EFR) which should be the successors of Superphenix

  12. Technical abstracts: Mechanical engineering, 1990

    International Nuclear Information System (INIS)

    Broesius, J.Y.

    1991-01-01

    This document is a compilation of the published, unclassified abstracts produced by mechanical engineers at Lawrence Livermore National Laboratory (LLNL) during the calendar year 1990. Many abstracts summarize work completed and published in report form. These are UCRL-JC series documents, which include the full text of articles to be published in journals and of papers to be presented at meetings, and UCID reports, which are informal documents. Not all UCIDs contain abstracts: short summaries were generated when abstracts were not included. Technical Abstracts also provides descriptions of those documents assigned to the UCRL-MI (miscellaneous) category. These are generally viewgraphs or photographs presented at meetings. An author index is provided at the back of this volume for cross referencing

  13. Judicial action and technical risk

    International Nuclear Information System (INIS)

    Buiren, S. van; Ballerstedt, E.; Grimm, D.

    1981-05-01

    In this study it is examined how the judiciary deals with those sections that are crucial for the use of nuclear energy. The authors get down to the pre-dominant problem of the law relating to technical safety. In the process they encounter the central dilemma of modern democracy, i.e. the strained relations which exist between judicial control and democratic responsibility. Since nuclear energy entered the market place, it has been the administrative courts which - in practice - have decided whether and to what extent nuclear energy may be used. On the one hand, this is a result of the fast growth of, and rapid change in, science and technology. On the other hand, it is a result of administrative law standards which have developed in the Federal Republic of Germany after World War II. The former requires the normative structure of the atomic law, the latter postulates how to deal with it. Legal protection against an act of public authority is guaranteed by the Basic Law and usually with some justification considered a splendid achievement of our state which is based on the rule of law. It has lead to developments in the atomic law and in many parts of the law relating to technical safety on which opinions are divided. In a dogmatic manner it has been legally examined to what extent an extensive review competence of the judiciary is a must, and whether there are any possibilities of judicial control of acts of public authorities without having to interfere with the original competence of administrations. (orig./HP) [de

  14. The assessment of technical risks

    International Nuclear Information System (INIS)

    Jaeger, T.A.

    1978-01-01

    The safety of technical systems is so difficult to assess because the concept 'risk' contains technical-scientific factors as well as components of individual and social psychology. Immediate or short-term hazards of human life as i.e. caused by the operation of industrial plants and mediate and thus long-term hazards have to be distinguished. Characteristic for the second hazard groups is the great time-lag before the effect takes place. Thus a causal relationship can be recognized only late and not definitely. Even when the causes have been obviated the effects still show. The development of a systems-analytical model as a basis of decisive processes for the introduction of highly endangered large-scale technologies seems particularly difficult. A starting point for the quantification of the risk can still be seen in the product of the probability of realization and the extent of the damage. Public opinion, however, does not base its evaluations on an objective concept of risk but tends to have an attitude of aversion against great and disastrous accidents. On the other hand, plenty of slight accidents are accepted much more easily, even when the amount of deadly victims from accidents reaches dimensions beyond those of the rare large-scale accidents. Here, mostly the damage possible but not the probability of its occurence is seen, let alone the general use of the new technology. The value of the mathematical models for estimating risks is mainly due to the fact that they are able to clear up decisions. (orig./HP) [de

  15. FOREX trading strategy formation using technical analysis

    OpenAIRE

    Klimavičius, Domas

    2010-01-01

    FOREX technical analysis indicators, their characteristics and capabilities are researched in this final master thesis. The main goal of this thesis is to determine if technical analysis indicators can recognise patterns in price movements and if they can predict future price movement. The first part of the thesis presents with FOREX theoretical aspects, its characteristics and participants. In the second part of the thesis FOREX analysis tools are overviewed, focusing on technical analysis. ...

  16. Technical specifications for the Bulk Shielding Reactor

    International Nuclear Information System (INIS)

    1982-04-01

    Technical specifications are presented concerning the safety limits and limiting safety system settings; limiting conditions for operation; surveillance requirements; design features; and administrative controls

  17. Factors Affecting Women Enrolment In Technical Institutions In Tanzania A Case Study Of Arusha Technical College

    OpenAIRE

    Glory B. Kaaya; Dr. Esther Waiganjo

    2015-01-01

    Abstract The purpose of this study was to investigate the factors affecting women enrolment in Technical Institutions in Tanzania by focusing on the women. The study examined in detail the factors affecting women enrolment in Technical institutions and Arusha Technical College in particular as well as exploring sexual dynamics within Technical Institutions. Moreover a number of theoretical frameworks were concerned basing on the objectives a case study design was employed involving both qua...

  18. Expressive/Exploratory Technical Writing (XTW) in Engineering: Shifting the Technical Writing Curriculum

    Science.gov (United States)

    Warnock, Scott; Kahn, Michael

    2007-01-01

    While the importance of "expressive writing," or informal, self-directed writing, has been well established, teachers underutilize it, particularly in technical writing courses. We introduce the term expressive/exploratory technical writing (XTW), which is the use of informal, self-directed writing to problem-solve in technical fields. We describe…

  19. Administrators' Perceptions of Career and Technical Education

    Science.gov (United States)

    Haussman, Charles E.

    2012-01-01

    Career and technical education was founded on the common practice of apprenticeships integrated into the public schools at the beginning of the 20th century as manual arts, which continued to evolve into a culture and practice of its own as vocational education, and into what is now career and technical education, with an evolving focus on college…

  20. Writing Clinic for Business and Technical Writers.

    Science.gov (United States)

    Mercer County Community Coll., Trenton, NJ.

    This document offers brief lesson plans for four courses: (1) an 8-hour refresher course for employees who write memos, short reports, and letters; (2) an 8-hour refresher course on creating a short document; (3) a 16-hour course on technical manual writing; and (4) an 8-hour course on technical manual writing. The courses were part of a workplace…