Performance of Kaolin Clay on the Concrete Pavement

Science.gov (United States)

Abdullah, M. E.; Jaya, R. P.; Shahafuddin, M. N. A.; Yaacob, H.; Ibrahim, M. H. Wan; Nazri, F. M.; Ramli, N. I.; Mohammed, A. A.

2018-05-01

This paper investigates the performance of concrete pavement containing kaolin clay with their engineering properties and to determine the optimum kaolin clay content. The concrete used throughout the study was designed as grade 30 MPa strength with constant water to cement ratio of 0.49. The compressive strength, flexural strength and water absorption test was conducted in this research. The concrete mix designed with kaolin clay as cement replacement comprises at 0%, 5%, 10% and 15% by the total weight of cement. The results indicate that the strength of pavement concrete decreases as the percentage of kaolin clay increases. It also shows that the water absorption increases with the percentage of cement replacement. However, 5% kaolin clay is found to be the optimum level to replace cement in a pavement concrete.

Rheological properties of kaolin and chemically simulated waste

International Nuclear Information System (INIS)

Selby, C.L.

1981-12-01

The Savannah River Laboratory is conducting tests to determine the best operating conditions of pumps used to transfer insoluble radioactive sludges from old to new waste tanks. Because it is not feasible to conduct these tests with real or chemically simulated sludges, kaolin clay is being used as a stand-in for the solid waste. The rheology tests described herein were conducted to determine whether the properties of kaolin were sufficiently similar to those of real sludge to permit meaningful pump tests. The rheology study showed that kaolin can be substituted for real waste to accurately determine pump performance. Once adequately sheared, kaolin properties were found to remain constant. Test results determined that kaolin should not be allowed to settle more than two weeks between pump tests. Water or supernate from the waste tanks can be used to dilute sludge on an equal volume basis because they identically affect the rheological properties of sludge. It was further found that the fluid properties of kaolin and waste are insensitive to temperature

Method removing radioactivity from kaolin

International Nuclear Information System (INIS)

Conley, R.F.

1978-01-01

A method of reducing the radioactivity found in naturally occurring kaolins to about 40% below its native value, and the leachable radiogenic components to less than 20% is described. This reduction is achieved by removing from the kaolin particles of a size less than 0.5 microns. This removal may be carried out by gravitational settling, flocculation of non-colloidal particles, or acid leaching

Adsorption of U(VI) onto kaolin studied by batch method

International Nuclear Information System (INIS)

Hongxia Zhang; Zhi Liu; Peizhuo Hu; Tonghuan Liu; Wangsuo Wu

2013-01-01

Adsorption of U(VI) on purified kaolin was studied by batch methods under ambient conditions, including contact time, pH, fulvic acid, etc. Three kinetic models were used to model the kinetic adsorption which was very well described by the pseudo-second-order rate equation, and the activation energy of adsorption was 52.20 kJ/mol. The Freundlich and Dubinin-Radushkevich models fitted the experimental data better than the Langmuir model for the adsorption and desorption isotherms. The thermodynamic parameters indicated that the adsorption of U(VI) on kaolin was an endothermic and spontaneous process. (author)

Entrained Flow Reactor Test of Potassium Capture by Kaolin

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2015-01-01

In the present study a method to simulate the reaction between gaseous KCl and kaolin at suspension fired condition was developed using a pilot-scale entrained flow reactor (EFR). Kaolin was injected into the EFR for primary test of this method. By adding kaolin, KCl can effectively be captured...

Physical properties and chemical composition of Segamat Kaolin, Johor, Malaysia

International Nuclear Information System (INIS)

Umar Hamzah; Learn, K.K.; Sahibin Rahim

2010-01-01

Kaolin is a source of secondary mineral as a product of a weathering process of primary minerals. Its main component is fine grain kaolinite (< 2 μm) and it also contains other elements such as aluminium and iron phyllosilicate as the pigment. Aluminium rich kaolin is light in colour with high plasticity and is normally used in the ceramic, plastic, paint, paper, pesticide, pharmacology and cosmetic industries. The physical and chemical characteristics of kaolins are important for its potential application. In this study, about 25 kaolin samples were hand-augered from depths of 1-2 m at Buloh Kasap Segamat, Johor, Malaysia. Chemical analysis carried out included determination of oxides and types of minerals by X-ray diffraction and X-ray fluorescence. Shrinkage rate, rupture modulus and water absorption rate tests were carried out in the physical properties analysis. Plastic and liquid limits of the kaolin were also measured for plastic index. The Segamat kaolin was light in colour due to its high silicate composition. The highest mineral content in the kaolin was kaolinite and quartz occurred as impurities. The low shrinkage rate showed that the kaolin was dense with little voids, hence very suitable for use in the ceramic industry. This kaolin has low water absorption, plasticity and durable according to the rupture modulus test. (author)

Fluoride retention by kaolin clay

DEFF Research Database (Denmark)

Kau, P. M. H.; Smith, D. W.; Binning, Philip John

1997-01-01

To evaluate the potential effectiveness of kaolin clay liners in storage of fluoride contaminated waste, an experimental study of the sorption and desorption behaviour of fluoride in kaolin clay was conducted. The degree of fluoride sorption by kaolin was found to depend on solution p......H and available fluoride concentration with equilibrium being achieved within 24 h. A site activation process involving the uptake of fluoride was also observed at the initial stages of sorption. This behaviour was attributed to a layer expansion process of the clay during sorption. The maximum fluoride sorption...... capacity was found to be 18.3 meq/100 g at pH 6 and 8.6 meq/100 g at pH 7. A competitive Langmuir sorption isotherm where sorption is dependant on both pH and fluoride concentration is employed to characterise the experimental sorption and desorption data. The sorption and desorption isotherms revealed...

Geochemistry of Selected Kaolins from Cameroon and Nigeria

Directory of Open Access Journals (Sweden)

Bukalo Nenita N.

2017-12-01

Full Text Available The geochemical characteristics of selected kaolins from Cameroon and Nigeria are presented, with an attempt to elucidate on their possible industrial applications by comparing them to world-known kaolin deposits. Major oxides concentrations were subjected to factor analyses in interpreting their relationships. Geochemical indices, including chemical index of alteration (CIA, chemical index of weathering (CIW and the index of compositional variability (ICV were computed and plotted on binary and ternary diagrams to determine the intensity of weathering of the kaolins and discriminate their different source rock types. Kaolinite was the major phase, followed by quartz, illite and goethite as minor phases. Minerals in trace phases included smectite, anatase, muscovite, gibbsite, microcline, palygorskite and calcite. Mean abundances of major oxides in wt% were: SiO2 (56.96>Al2O3 (24.09>Fe2O3 (3.78>TiO2 (1.53> K2O (1.26> MgO (0.27>CaO (0.20>Na2O (0.17>P2O5 (0.05>MnO (0.04. The CIW versus CIA and ICV versus CIA plots showed that most of the kaolins clearly depicted extreme silicate weathering. The current applications of kaolins from Cameroon and Nigeria include ceramics and manufacturing of bricks and tiles. Low MgO, CaO, Na2O, K2O and TiO2 further position the kaolins for pharmaceutics, cosmetics, rubber and plastic applications. Thus, the studied kaolins have the potential to contribute to improved economic development of these countries.

Geochemistry of Selected Kaolins from Cameroon and Nigeria

Science.gov (United States)

Bukalo, Nenita N.; Ekosse, Georges-Ivo E.; Odiyo, John O.; Ogola, Jason S.

2017-12-01

The geochemical characteristics of selected kaolins from Cameroon and Nigeria are presented, with an attempt to elucidate on their possible industrial applications by comparing them to world-known kaolin deposits. Major oxides concentrations were subjected to factor analyses in interpreting their relationships. Geochemical indices, including chemical index of alteration (CIA), chemical index of weathering (CIW) and the index of compositional variability (ICV) were computed and plotted on binary and ternary diagrams to determine the intensity of weathering of the kaolins and discriminate their different source rock types. Kaolinite was the major phase, followed by quartz, illite and goethite as minor phases. Minerals in trace phases included smectite, anatase, muscovite, gibbsite, microcline, palygorskite and calcite. Mean abundances of major oxides in wt% were: SiO2 (56.96)>Al2O3 (24.09)>Fe2O3 (3.78)>TiO2 (1.53)> K2O (1.26)> MgO (0.27)>CaO (0.20)>Na2O (0.17)>P2O5 (0.05)>MnO (0.04). The CIW versus CIA and ICV versus CIA plots showed that most of the kaolins clearly depicted extreme silicate weathering. The current applications of kaolins from Cameroon and Nigeria include ceramics and manufacturing of bricks and tiles. Low MgO, CaO, Na2O, K2O and TiO2 further position the kaolins for pharmaceutics, cosmetics, rubber and plastic applications. Thus, the studied kaolins have the potential to contribute to improved economic development of these countries.

Short communication: Laboratory approach to the use of sulphur and kaolin as preventive control against Drosophila suzukii

Energy Technology Data Exchange (ETDEWEB)

Pérez-Guerrero, S.; Molina, J.M.

2016-11-01

Drosophila suzukii (Matsumura, 1931) is an invasive pest from South East Asia that was detected for the first time in Southern Europe in 2008. This species can damage a wide range of soft-skinned fruits crops affecting ripening fruits and causing important economic losses. Since the exclusive use of chemical insecticides for controlling D. suzukii may prompt the appearance of resistance and environmental pollution, alternative methods compatible with sustainable management are required. In this study, commercial formulations of powdered sulphur and kaolin were tested as a preventive method applied to blueberry fruits under laboratory conditions. In no-choice assay, powdered sulphur had a significant effect on oviposition and adult emergency with reductions of 76% and 77%, respectively. In addition, sulphur displayed a significant toxicity on males and lethal effect with over 40% adult mortality seven days after exposure. The choice assay confirmed and improved the powdered sulphur effects, with reductions of 98% and 96% in oviposition and adult emergence, respectively. In contrast, kaolin produced no significant reduction in infestation and adult mortality during no-choice and choice assays. These outcomes suggest that preventive use of powdered sulphur could be considered for sustainable control of D. suzukii in some berry crops. (Author)

Short communication: Laboratory approach to the use of sulphur and kaolin as preventive control against Drosophila suzukii

Directory of Open Access Journals (Sweden)

Sergio Pérez-Guerrero

2016-06-01

Full Text Available Drosophila suzukii (Matsumura, 1931 is an invasive pest from South East Asia that was detected for the first time in Southern Europe in 2008. This species can damage a wide range of soft-skinned fruits crops affecting ripening fruits and causing important economic losses. Since the exclusive use of chemical insecticides for controlling D. suzukii may prompt the appearance of resistance and environmental pollution, alternative methods compatible with sustainable management are required. In this study, commercial formulations of powdered sulphur and kaolin were tested as a preventive method applied to blueberry fruits under laboratory conditions. In no-choice assay, powdered sulphur had a significant effect on oviposition and adult emergency with reductions of 76% and 77%, respectively. In addition, sulphur displayed a significant toxicity on males and lethal effect with over 40% adult mortality seven days after exposure. The choice assay confirmed and improved the powdered sulphur effects, with reductions of 98% and 96% in oviposition and adult emergence, respectively. In contrast, kaolin produced no significant reduction in infestation and adult mortality during no-choice and choice assays. These outcomes suggest that preventive use of powdered sulphur could be considered for sustainable control of D. suzukii in some berry crops.

Effects of kaolin particle films on the life span of an orb-weaver spider.

Science.gov (United States)

Benhadi-Marín, Jacinto; Pereira, José Alberto; Santos, Sónia A P

2016-02-01

Araniella cucurbitina (Araneae: Araneidae) is a widespread orb-weaver spider commonly found in agroecosystems. Mineral particle films such as kaolin, due to their protective or anti-feeding action, can represent an alternative to pesticides, especially in organic farming systems, but little is known about its effects on A. cucurbitina. Therefore, we tested the effect of kaolin sprays on the life span of A. cucurbitina under laboratory conditions. Four treatments were tested encompassing different exposure routes. Thus, kaolin sprays were applied on (i) the surface, (ii) the prey (fly), (iii) the spider and (iv) both spider & prey. A control group was tested with water in each treatment. Results showed that sprays of kaolin significantly affected the survival of A. curcubitina when applications were done on the surface and on both spider & prey registering a reduction of 48% and 56%, respectively. Spiders in control obtained higher probability of reaching alive at the end of the assay than those treated with kaolin. Differences observed can be explained by the feeding behavior of the species and may depend on the consumption of the web by the spider and the ratio spider/fly for body size. Copyright © 2015 Elsevier Ltd. All rights reserved.

The hydrogen isotopic composition of kaolin minerals in Japan

International Nuclear Information System (INIS)

Marumo, Katsumi; Nagasawa, Keinosuke; Kuroda, Yoshimasu.

1979-01-01

Hydrogen isotopic composition (D/H ratio) was determined for kaolin minerals from geothermal areas and sedimentary and hydrothermal kaolin deposits in Japan. On the Ohnuma, Matsukawa, and Ohtake geothermal areas, the hydrogen isotopic fractionation factor between kaolin minerals and water was calculated to fall between 0.97 and 0.99 for the temperature range of 50 to 200 0 C, a fact which shows that the temperature of formation has no important effect on the D/H ratio of kaolin minerals. D/H ratio of kaolinites and dickites from many kaolin deposits shows local variation, and seems to correlate with isotopic variation of the present-day meteoric surface water. Exceptions are seen in some kaolin deposits such as Shokozan, Hiroshima Prefecture, where kaolinite and dickite have considerably high values of D/H ratio, and seem to have reacted with water rich in deuterium. D/H ratio of halloysite is not correlated with that of the present-day meteoric surface water. As Lawrence and Taylor (1971) pointed out, the original D/H ratio of constitutional water of halloysite is not preserved because of the isotopic exchange between the interlayer water and the constitutional water. (author)

XANES at the silicon k-edge in the kaolin-meta kaolin-geopolymer system

International Nuclear Information System (INIS)

Lima, F.T.; Silva, F.J.; Thaumaturgo, C.

2005-01-01

The geo polymer synthesis process optimization pretends to control the re logical and mechanical properties. The Al/Si ratio is the main variable that governs the geo polymerization process. This control occurs by changing temperature, pressure and chemical composition of the geo polymer. Thermal analysis (DTA/DSC), microscopic (SEM/TEM) and spectroscopic (FTIR, XRD, SAXS, EXAFS and XANES) techniques have been used to characterize these inorganic systems. In this work, XANES spectra of the k-edge silicon (Si) of the kaolin-meta kaolin-geo polymer are presented. The XANES spectra provides the oxidation state and structural information about the present studied atom: Silicon (Si). (author)

Effect of surface modified kaolin on properties of polypropylene grafted maleic anhydride

Science.gov (United States)

Yang, Ni; Zhang, Zuo-Cai; Ma, Ning; Liu, Huan-Li; Zhan, Xue-Qing; Li, Bing; Gao, Wei; Tsai, Fang-Chang; Jiang, Tao; Chang, Chang-Jung; Chiang, Tai-Chin; Shi, Dean

To achieve reinforcement of mechanical and thermal performances of polypropylene (PP) product, this work aimed at fabrication of surface modified kaolin (M-kaolin) filled polypropylene grafted maleic anhydride (PP-g-MAH) composites with varying contents of fillers and investigation of their mechanical and thermal properties. And the prepared PP-g-MAH/M-kaolin composites were characterized by means of Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). Fracture analysis by SEM showed M-kaolin particles were well dispersed in the PP-g-MAH matrix. Mechanical behaviors were determined by tensile strength, tensile strain at break and impact strength analysis. Impact strength of PP-g-MAH/2 wt% M-kaolin composites was improved up to 30% comparing with unfilled composites. Thermostability had been found enhanced when M-kaolin added. The results revealed PP-g-MAH/M-kaolin composites showed the optimal thermal and mechanical properties when 2 wt% of M-kaolin was added.

Merger of waste in kaolin panels medium density

International Nuclear Information System (INIS)

Bezerra, A.F.C.; Santana, L.N.L.; Neves, G.A.

2011-01-01

Medium-density panels are molded under pressure and temperature and have physical and mechanical properties similar to those of solid wood. Their composition involves fibers of eucalyptus and pine, but other residues as kaolin waste can be incorporated. The objective was to manufacture medium density panels incorporating kaolin waste and compare the physical, chemical and mechanical properties of these with other commercials. The residue was subjected to the following characterization tests: X-ray diffraction, chemical analysis, differential thermal analysis, thermal gravimetric analysis and size analysis.Through the process of pressing the samples were prepared, they were evaluated for their flexural strength and tensile strength perpendicular to the water absorption / swelling in thickness, density and moisture content. According to the analyzed results, we conclude that samples having the residue had lower levels of swelling, tensile and flexural strength and higher levels of absorption.(author)

PENGARUH METODE AKTIVASI PADA KEMAMPUAN KAOLIN SEBAGAI ADSORBEN BESI (FE AIR SUMUR GARUDA

Directory of Open Access Journals (Sweden)

Tirta Indah Wulan Sari

2016-10-01

Full Text Available Kaolin is a mineral found in sedimentary rocks known as clay stone. Kaolin widely applied in industries such as paper, ceramics, rubber, plastics, paint, glassfiber, and cosmetics. This study aimed to determine the effect on the ability of kaolin activation methods as adsorbent. The study was conducted by activation of kaolin in physics, chemistry, and chemistry-physics. Physical activation was done by heating kaolin at 700 ° C in a furnace for 30 minutes and for the chemical activation, the addition of 0.25 M HCl in kaolin with stirring speed of 200 rpm for 60 minutes, while the chemical-physical activation, the addition of 0.25 M HCl to the kaolin and continued warming in furnace at 700 ° C. The kaolin activation was to produce an adsorbent that is able to absorb iron (Fe optimally. From this study, the optimum activation obtained for kaolin in adsorbing Fe is the chemical activation. Chemical activated kaolin adsorbent having a large adsorption capacity of the ion Fe which resulted in decreased content of iron (Fe to 0.04 mg / L.

X-ray diffraction and thermal analysis of kaolins particle size fractions

Directory of Open Access Journals (Sweden)

Patricia dos Santos

2013-09-01

Full Text Available Kaolins are common geological materials and have high concentrations of kaolinite as well as the clay fraction of tropical and subtropical soils of Brazil. The characterization of kaolin is a proxy of assessing the contribution of kaolinite to important soil chemical and mineralogical attributes. This study evaluated four kaolins (commercial kaolin A (CCA, commercial kaolin B (CCB, pink sandy kaolin A (CRA and green sandy kaolin A (CVA in the original form and after particle size separation into: sand (200-53 mm, coarse silt (53-20 m, fine silt (20-2 m, large clay (2-1m, medium clay (1-0.5 m and fine clay (<0.5m fractions. The minerals were identified by X-ray diffraction (XRD and evaluated for crystallinity (kaolinite and halloysite through indexes Hughes and Brown, Amigó, Bramão and the dehydroxylation temperature. The physical fractionation was efficient to concentrate minerals in specific size fractions which were not identified in the original material. In CCA kaolin was concentrated one mineral which remains unidentified in fine fractions, in kaolin CRA, zircon was concentrated in the coarse silt and different silicates in the fine fractions, in kaolin CCB were concentrated kaolinite and a silicate in the medium and coarse clay fractions. The estimate by X-ray diffraction overestimated the amount of kaolinite and halloysite underestimated when compared to quantification by thermal gravimetric analysis The crystallinity index exhibit different behaviors depending on the mineralogy of each material, thus the correlation between the crystallinity of kaolinite and / or halloysite and other variables, may be compromised, especially in materials with distinct geological origins.

ADSORPTION OF PARAQUAT DICHLORIDE TO KAOLIN PARTICLES AND TO MIXTURES OF KAOLIN AND HEMATITE PARTICLES

Directory of Open Access Journals (Sweden)

Dina Alexandra Martins

2015-03-01

Full Text Available Deliberate contamination with pesticides is a potential risk to water security, due to the availability of these contaminants and the fact that they do not need special expertise to handle or apply. Adsorption of the herbicide paraquat from an aqueous solution to suspended particles of kaolin and kaolin/hematite mixture was investigated by kinetic and equilibrium assays, taking into consideration several parameters such as initial pH, sorbent dosage and agitation speed. The results showed that the adsorption process is quite fast, reaching an 18% reduction in paraquat concentration in a very short period of time. The addition of hematite particles to kaolin suspension had no apparent effect on the maximum amount of paraquat adsorbed. Kinetic parameters were determined by fitting the pseudo-second order model to the experimental data (correlation coefficients close to 1. Isotherm studies indicate an inhibitory effect, promoted by hematite particles, that was not detected in the adsorption assays. Equilibrium data was best adjusted using the Langmuir model which yielded higher correlation coefficient values and smaller normalized standard deviations.

ADSORPTION OF GIBBERELLIC ACID ONTO NATURAL KAOLIN FROM TATAKAN, SOUTH KALIMANTAN

Directory of Open Access Journals (Sweden)

Sunardi Sunardi

2010-06-01

Full Text Available Adsorption of gibberellic acid (GA3 onto raw and purified kaolin from Tatakan, South Kalimantan was investigated in this study. Purification process was done by sedimentation to obtain relative pure kaolinite. Raw and purified kaolin samples were characterized by Fourier transformed infrared (FTIR spectroscopy and X-ray diffractometer (XRD. The adsorption process was carried out in a batch system and the effect of pH, contact time and GA3 concentration were experimentally studied to evaluate the adsorption capacity. The amount of GA3 adsorbed was determined by UV spectrophotometer. The result showed that the raw kaolin from South Kalimantan consist of 53.36% kaolinite, 29.47% halloysite, 4.47% chlorite, 11.32% quartz and 1.38% christobalite and the purified kaolin consist of 73.03% kaolinite, 22.6% halloysite, 0.77% chlorite, 1.37% quartz and 2.23% christobalite Adsorption experimental indicate that the optimum adsorption took place at pH 7 and contact time for 4 h. Adsorption of GA3 was described by the Langmuir adsorption isotherm model with adsorption capacity of 8.91 mg/g on raw kaolin and 10.38 mg/g on purified kaolin.   Keywords: kaolin, gibberellic acid, adsorption

Centrifuge modelling of rigid piles in soft clay

DEFF Research Database (Denmark)

Klinkvort, R.T.; Poder, M.; Truong, P.

2016-01-01

of this study is to employ centrifuge modelling in order to derive experimental p-y curves for rigid piles embedded in over-consolidated soft clay. A kaolin clay sample was prepared and pre-consolidated by applying a constant pressure at the soil surface, while different over-consolidation ratios were achieved...

Bio-beneficiation of kaolin and feldspar and its effect on fired

Indian Academy of Sciences (India)

Presence of iron compounds as impurities in kaolin and feldspar, impart reddish colour to ceramic products manufactured using these minerals. The quality of kaolin and feldspar was enriched mainly through iron removal by biological methods. Bacteria isolated from kaolin of Indian origin were used for bioleaching.

Bauxite and Kaolin Deposits of the Irwinton district, Georgia

Science.gov (United States)

Lang, Walter B.; Warren, Walter C.; Thompson, Raymond M.; Overstreet, Elizabeth F.

1965-01-01

The Irwinton district is in the central part of Georgia at the inner margin of the Coastal Plain province. The oldest rocks exposed in the district are crystalline rocks of the Piedmont province. They are unconformably overlain by nonmarine sedimentary strata of Late Cretaceous age, including gravel, micaceous sand, and lenses of kaolin. Bauxite has been found in a few of the kaolin lenses near the top of the sequence of these strata. During a long period prior to deposition of the over- lying marine beds of the Claiborne and Jackson Groups (middle and upper Eocene), the Upper Cretaceous strata were subjected to subaerial erosion. The bauxite deposits are considered to have formed during this period. They range in thickness from a few inches to more than 10 feet and occupy areas ranging from a few square feet to more than 5 acres. Most of the known bauxite deposits lie along the valleys of Commissioners Creek and Big Sandy Creek in Wilkinson County. The kaolin lenses are much larger than the bauxite deposits; some of the lenses underlie more than 200 acres and are more than 20 feet thick. Bauxite was discovered in the district in 1907 and was mined from 1910 to 1928. A few additional carloads of ore were shipped in 1941 and 1942, but no ore has been mined since that time. Reserves of high-grade bauxite are very small. Reserves of all grades of bauxite plus bauxitic clay may be about 400,000 long tons. The Irwinton district is the principal source of high-grade kaolin in the United States. The presence of kaolin here has been known since early colo- nial time, and it has been mined continuously since 1897. Production in 1959 was 1,940,279 short tons. The reserves of kaolin are very large but have never been adequately measured. Reserves of first and second grade kaolin may be 67 to 84 million short tons. Kaolin of lower grade is present in larger quantity.

Removal of Phenol in Aqueous Solution Using Kaolin Mineral Clay

International Nuclear Information System (INIS)

Sayed, M.S.

2008-01-01

Kaolin clay were tested for phenol removal as toxic liquid waste from aqueous waste water. Several experimental conditions such as weight and particle size of clay were investigated to study batch kinetic techniques, also the ph and concentration of the phenol solution were carried out. The stability of the Langmuir adsorption model of the equilibrium data were studied for phenol sorbent clay system. Infrared spectra, thermogravimetric and differential thermal analysis techniques were used to characterize the behavior of kaolin clay and kaolin clay saturated with phenol. The results obtained showed that kaolin clay could be used successfully as an efficient sorbent material to remove phenol from aqueous solution

Shear Strength of Stabilized Kaolin Soil Using Liquid Polymer

Science.gov (United States)

Azhar, A. T. S.; Fazlina, M. I. S.; Nizam, Z. M.; Fairus, Y. M.; Hakimi, M. N. A.; Riduan, Y.; Faizal, P.

2017-08-01

The purpose of this research is to investigate the suitability of polymer in soil stabilization by examining its strength to withstand compressive strength. Throughout this research study, manufactured polymer was used as a chemical liquid soil stabilizer. The liquid polymer was diluted using a proposed dilution factor of 1 : 3 (1 part polymer: 3 parts distilled water) to preserve the workability of the polymer in kaolin mixture. A mold with a diameter of 50 mm and a height of 100 mm was prepared. Kaolin soil was mixed with different percentages of polymer from 10%, 15%, 20%, 25%, 30% and 35% of the mass of the kaolin clay sample. Kaolin mixtures were tested after a curing period of 3 days, 7 days, 14 days and 28 days respectively. The physical properties were determined by conducting a moisture content test and Atterberg limit test which comprise of liquid limit, plastic limit and shrinkage limit. Meanwhile, the mechanical properties of the soil shear strength were identified through an unconfined compressive strength (UCS) test. Stabilized kaolin soil showed the highest compressive strength value when it was mixed with 35% of polymer compared to other percentages that marked an increment in strength which are 45.72% (3 days), 67.57% (7 days), 81.73% (14 days) and 77.84% (28 days). Hence, the most effective percentage of liquid polymer which should be used to increase the strength of kaolin soil is 35%.

Contemporary technology of enrichment of kaolins of Angren deposit. II. Removal of impurities and whitening of kaolins: using electrophysical and chemical methods of cleaning

International Nuclear Information System (INIS)

Krivorotov, V.F.; Usmanov, ZH.M.; Fridman, A.A.

2012-01-01

The contemporary methods of enrichment of Angren kaolins have been described. The electrophoresis and chemical whitening are demonstrated to be the most effective methods of scavenging. Application of ultrasonic dispersion, electrophoresis and chemical whitening methods allows one to obtain kaolin with whiteness ≅ 88% and content of iron oxides ≅ 0.4%. Using such kaolin as a sorbent at de coloration of plant oil have been shown good adsorption properties, meeting the level of world-wide standards for such class of materials. (authors)

Adsorption characteristics of brilliant green dye on kaolin

International Nuclear Information System (INIS)

Nandi, B.K.; Goswami, A.; Purkait, M.K.

2009-01-01

Experimental investigations were carried out to adsorb toxic brilliant green dye from aqueous medium using kaolin as an adsorbent. Characterization of kaolin is done by measuring: (i) particle size distribution using particle size analyzer, (ii) BET surface area using BET surface analyzer, and (iii) structural analysis using X-ray diffractometer. The effects of initial dye concentration, contact time, kaolin dose, stirring speed, pH and temperature were studied for the adsorption of brilliant green in batch mode. Adsorption experiments indicate that the extent of adsorption is strongly dependent on pH of solution. Free energy of adsorption (ΔG 0 ), enthalpy (ΔH 0 ) and entropy (ΔS 0 ) changes are calculated to know the nature of adsorption. The calculated values of ΔG 0 at 299 K and 323 K indicate that the adsorption process is spontaneous. The estimated values of ΔH 0 and ΔS 0 both show the negative sign, which indicate that the adsorption process is exothermic and the dye molecules are organized on the kaolin surface in less randomly fashion than in solution. The adsorption kinetic has been described by first-order, pseudo-second-order and intra-particle-diffusion models. It was observed that the rate of dye adsorption follows pseudo-second-order model for the dye concentration range studied in the present case. Standard adsorption isotherms were used to fit the experimental equilibrium data. It was found that the adsorption of brilliant green on kaolin follows the Langmuir adsorption isotherm

Assembling strategy to synthesize palladium modified kaolin nanocomposites with different morphologies

Science.gov (United States)

Li, Xiaoyu; Ouyang, Jing; Zhou, Yonghua; Yang, Huaming

2015-09-01

Nanocomposites of aluminosilicate minerals, kaolins (kaolinite and halloysite) with natural different morphologies assembling with palladium (Pd) nanoparticles have been successfully synthesized through strong electrostatic adsorption and chemical bonding after surface modification with 3-aminopropyl triethoxysilane (APTES). Meanwhile, the influence of different morphologies supports on catalytic hydrogenation properties was explored. The surface concentration of amino groups on the kaolins was related to the morphology and surface nature. Electronmicroscopy revealed that the monodisperse Pd nanoparticles were uniformly deposited onto the surface of kaolins, ranging in diameter from 0.5 nm to 5.5 nm. The functional groups could not only improve the dispersion of kaolins with different morphologies in solution, but also enhance the interaction between Pd precursors and kaolins, thus preventing small Pd nanoparticles from agglomerating and leading to high activity for the catalytic hydrogenation of styrene. Pd-FK@APTES was more active compared to other samples. Selecting the kaolin morphology with a different surface nature allows the selective surface modification of a larger fraction of the reactive facets on which the active sites can be enriched and tuned. This desirable surface coordination of catalytically active atoms could substantially improve catalytic activity.

Structure and properties of pregelatinized cassava starch/kaolin composites

International Nuclear Information System (INIS)

Kaewtatip, Kaewta; Tanrattanakul, Varaporn

2012-01-01

Highlights: ► Pregelatinized starch/kaolin composites were prepared using compression molding. ► The tensile strengths of the composites were higher than for thermoplastic starch. ► Degradation temperatures of the composites were higher than for thermoplastic starch. ► The retrogradation behavior of the composites was hindered by kaolin. -- Abstract: Pregelatinized cassava starch/kaolin composites were prepared using compression molding. The morphology of the fractured surfaces, retrogradation behavior, thermal decomposition temperatures and mechanical properties of the composites were investigated using scanning election microscopy (SEM), X-ray diffraction (XRD), thermal gravimetric analysis (TGA) and tensile testing, respectively. The tensile strengths and thermal degradation temperatures of the composites were higher than for thermoplastic starch (TPS). The retrogradation behavior of the composites was hindered by kaolin. The water absorption was measured after aging for 12 and 45 days at a relative humidity (RH) of 15% and 55%. It indicated that all the composites displayed lower water absorption values than TPS.

Comparative studies on physico-mechanical properties of composite materials of low density polyethylene and raw/calcined kaolin

Directory of Open Access Journals (Sweden)

Amit Mallik

2015-06-01

Full Text Available The paper describes the preparation of the composite materials of low density polyethylene (LDPE as the base mixed separately with raw kaolin and the same calcined at 800 °C under the same variation in weight percentage using single-screw extruder and a mixing machine operated at a temperature between 190 and 200 °C. Some of the mechanical and physical properties such as Young's modulus, elongation at break, shore hardness and water absorption were determined at different weight fractions of filler (0, 2, 7, 10 and 15%. It was found that the addition of filler increases the mechanical properties. Absorption test was done in water at different immersion times for different composites. The degree of water absorption of composite materials was found to decrease with increasing wt% of kaolin filler (0–15% according to Fick's law. Calcined kaolin produces better mechanical properties than raw kaolin.

Preparation of Modified Kaolin Filler with Cesium and Its Application in Security Paper

Directory of Open Access Journals (Sweden)

Houssni El-Saied

2013-01-01

Full Text Available In this study, cesium was added intentionally during paper manufacture for protecting the papers against forgery and counterfeiting by sorbing cesium ions (Cs+ on kaolin, used as special filler in papermaking. The sorption of cesium from aqueous solution by kaolin was studied as a function of pH, shaking time, cesium initial concentration, and mass of kaolin using batch technique. The results showed that a solution containing 10 mg/L Cs+ and 250 mg of kaolin at pH 6 can be used to modify the kaolin. Paper handsheets were prepared containing various percentages of the modified kaolin. The mechanical and optical properties of paper handsheets were studied. The prepared paper handsheets were irradiated by gamma irradiation using different doses. Fourier transform infrared (FTIR spectroscopy was used to study the effect of kaolin modification by cesium and gamma irradiation on paper handsheets properties. The results indicated that modified kaolin enhanced the mechanical and optical properties of paper handsheets. Electron spin resonance (ESR spectroscopy and laser-induced breakdown spectroscopy (LIBS were also used. They provided rapid, sensitive and nondestructive techniques in differentiating between different questioned documents. This study presents a new concept in manufacturing security papers and anticounterfeiting applications.

Mussel inspired preparation of amine-functionalized Kaolin for effective removal of heavy metal ions

Energy Technology Data Exchange (ETDEWEB)

Huang, Qiang; Liu, Meiying; Deng, Fengjie [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang, 330031 (China); Wang, Ke [Department of Chemistry and the Tsinghua Center for Frontier Polymer Research, Tsinghua University, Beijing, 100084 (China); Huang, Hongye; Xu, Dazhuang; Zeng, Guangjian [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang, 330031 (China); Zhang, Xiaoyong, E-mail: xiaoyongzhang1980@gmail.com [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang, 330031 (China); Wei, Yen [Department of Chemistry and the Tsinghua Center for Frontier Polymer Research, Tsinghua University, Beijing, 100084 (China)

2016-09-15

Adsorption has been well regarded as a promising and efficient method for the removal of low concentration heavy metal ions in aqueous solutions. And kaolin has been considered as a kind of low cost and environment-friendly adsorbent for its abundant in nature. But the low adsorption capacity to heavy metal ions and severe aggregation in solution restrains its application. In this work, an environment-friendly adsorbent (denoted as Kaolin-PDA-PEI) was prepared based on mussel inspired chemistry and Michael addition reaction between high reaction activity of polydopamine (PDA) and polyethyleneimine (PEI), which was possesses a number of amine groups. The amine groups have displayed strong adsorption affinity towards copper ions. The successful modification of Kaolin by PDA and PEI was confirmed by a series of analyses, such as Fourier transform infrared spectroscopy, transmission electron microscopy, thermal gravimetry analysis and X-ray photoelectron spectroscopy. The effects of various parameters such as contact time, pH, initial concentrations of copper ions and temperature on copper ion adsorption by Kaolin-PDA-PEI were investigated. Kaolin-PDA-PEI shows higher adsorption capacity as compared with the raw Kaolin. The kinetic adsorption data were analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion model. The Langmuir isotherm and Freundlich isotherm equilibrium model were applied to adsorption isotherm data to find the better fit isotherm. The results showed that adsorption process was well fitted by Langmuir isotherm model. The values of thermodynamics constants such as entropy change (ΔS{sup 0}), enthalpy change (ΔH{sup 0}) and Gibbs free energy (ΔG{sup 0}) were also calculated. The results indicated that the adsorption process of Kaolin-PDA-PEI were endothermic and spontaneous. - Graphical abstract: Amino groups functionalized Kaolin was facilely prepared via mussel inspired chemistry. The modified Kaolin exhibited much

Mussel inspired preparation of amine-functionalized Kaolin for effective removal of heavy metal ions

International Nuclear Information System (INIS)

Huang, Qiang; Liu, Meiying; Deng, Fengjie; Wang, Ke; Huang, Hongye; Xu, Dazhuang; Zeng, Guangjian; Zhang, Xiaoyong; Wei, Yen

2016-01-01

Adsorption has been well regarded as a promising and efficient method for the removal of low concentration heavy metal ions in aqueous solutions. And kaolin has been considered as a kind of low cost and environment-friendly adsorbent for its abundant in nature. But the low adsorption capacity to heavy metal ions and severe aggregation in solution restrains its application. In this work, an environment-friendly adsorbent (denoted as Kaolin-PDA-PEI) was prepared based on mussel inspired chemistry and Michael addition reaction between high reaction activity of polydopamine (PDA) and polyethyleneimine (PEI), which was possesses a number of amine groups. The amine groups have displayed strong adsorption affinity towards copper ions. The successful modification of Kaolin by PDA and PEI was confirmed by a series of analyses, such as Fourier transform infrared spectroscopy, transmission electron microscopy, thermal gravimetry analysis and X-ray photoelectron spectroscopy. The effects of various parameters such as contact time, pH, initial concentrations of copper ions and temperature on copper ion adsorption by Kaolin-PDA-PEI were investigated. Kaolin-PDA-PEI shows higher adsorption capacity as compared with the raw Kaolin. The kinetic adsorption data were analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion model. The Langmuir isotherm and Freundlich isotherm equilibrium model were applied to adsorption isotherm data to find the better fit isotherm. The results showed that adsorption process was well fitted by Langmuir isotherm model. The values of thermodynamics constants such as entropy change (ΔS"0), enthalpy change (ΔH"0) and Gibbs free energy (ΔG"0) were also calculated. The results indicated that the adsorption process of Kaolin-PDA-PEI were endothermic and spontaneous. - Graphical abstract: Amino groups functionalized Kaolin was facilely prepared via mussel inspired chemistry. The modified Kaolin exhibited much enhanced adsorption

Synthesis of microporous material faujasite-type from kaolin waste

International Nuclear Information System (INIS)

Hildebrando, E.A.; Valenzuela-Diaz, F.R.; Angelica, R.S.; Neves, R.F.

2010-01-01

Zeolite with structure faujasite was synthesized using kaolin waste from kaolin processing industries for paper coating as predominant source of silicon and aluminum; the starting material was characterized by XRF, XRD, DTA/TG, SEM, and products obtained by XRD and SEM. Synthesis in hydrothermal conditions occurred on autoclave and time-temperature effects, as well as the relationship Si/Al were considered. The results show that the methodology developed with the waste of calcined kaolin reacting at 90 deg C for 20 hours in an alkaline medium, in the presence of an additional source of silica was obtained zeolite Y as single phase present in the product. (author)

Synthesis and characterization of kaolin with polystyrene via in-situ polymerization and their application on polypropylene

International Nuclear Information System (INIS)

Zhao, Songfang; Qiu, Shangchang; Zheng, Yuying; Cheng, Lei; Guo, Yong

2011-01-01

To improve both the mechanical and thermal properties of kaolin/polypropylene (PP) composites, kaolin was modified by using 3-(trimethoxysilyl) propylmethacrylate (YDH-570) as a coupling agent to form polymerizable particle. Styrene was radically polymerized through the immobilized vinyl using benzoyl peroxide (BPO) as an initiator. Fourier transform-infrared (FTIR) spectroscopy, particle size distribution, X-ray diffraction (XRD) and thermo-gravimetric analysis (TGA) well demonstrated that the kaolin-polystyrene particles were successfully synthesized via in-situ polymerization. While the modified kaolin and raw kaolin were introduced into the PP matrix, it could be concluded that modified kaolin/PP composites have better mechanical and thermal properties than raw kaolin/PP composites, and these improvements were attributed to the desirable dispersion of kaolin in PP matrix.

Use of airborne gamma-ray spectrometry for kaolin exploration

Science.gov (United States)

Tourlière, B.; Perrin, J.; Le Berre, P.; Pasquet, J. F.

2003-08-01

Airborne gamma-ray spectrometry was used to define targets with kaolin potential in the Armorican Massif of Brittany, France. This exploration method is based on the principle that kaolinite, an aluminosilicate clay mineral constituting kaolin, is formed by the hydrolysis of potash feldspar with the elimination of potassium. Therefore, potassium contrast between favourable host-rock such as a leucogranite and kaolin occurrence is likely a significant pathfinder. As the relationship between the potassium-40 recorded by an airborne gamma-ray spectrometer and total potassium is constant, such data provide us a direct measurement of the potassium content of the ground flown over. Our study tested this by calculating, for each geological unit, the difference between the measured and average potassium content calculated for a given geological formation. The study was based on (i) a recent (1998) high-definition airborne geophysical survey over the Armorican Massif undertaken on behalf of the French Government, and (ii) new geological compilation maps covering the same region. Depleted zones, where the measured potassium is less than the average potassium content calculated target areas with high potential of containing kaolin, provided that the unit was originally rich in potash feldspar. By applying this method to the entire Armorican Massif, it was possible to identify 150 potassium-depleted zones, including 115 that were subjected to rapid field checks and 36 that contained kaolin (21 new discoveries). This method, which is both safe for the environment and easy to use, is therefore a good tool for rapidly defining targets with kaolin potential at a regional scale. The method may also have possibilities in exploring for other types of deposit characterised by an enrichment or depletion in U, K and/or Th.

Surface modification of calcined kaolin with toluene diisocyanate based on high energy ball milling

International Nuclear Information System (INIS)

Yuan, Yongbing; Chen, Hongling; Lin, Jinbin; Ji, Yan

2013-01-01

The surface of calcined kaolin particle was modified with toluene diisocyanate (TDI) by using high energy ball milling. The prepared hybrids were characterized by FT-IR, MAS NMR, thermal analysis (TGA-DSC), static water contact angle (CA), apparent viscosity and transmission electron microscopy (TEM). FT-IR and MAS NMR spectra demonstrated that TDI molecules were chemically anchored to kaolin surface after modification. The results of thermal analysis showed that the maximum grafting ratio reached up to 446.61% when the mass ratio of TDI/kaolin was 0.5:1.0, and CA measurements revealed that the resultant hybrids exhibited strong hydrophobicity (148.82°). Apparent viscosity and TEM were employed to examine the dispersion properties of blank and modified kaolin particles in poly (dimenthylsiloxane) matrix. The results illustrated that the dispersion stability depended strongly on the grafting ratio of TDI, neither too low nor too high achieved uniform and stable dispersion, and the favorable grafting ratio was obtained when the mass ratio of TDI/kaolin was 0.2:1.0. Further modification of TDI/kaolin (mass ration of TDI/kaolin, 1.0:1.0) particles with bis(aminopropyl)-terminated-poly(dimethylsiloxane) (APS) was also investigated. TEM evidenced that the dispersion properties of the obtained TDI/APS/kaolin particles were remarkably improved in octamethyl cyclotetrasiloxane compared with the original TDI/kaolin particles.

Surface modification of calcined kaolin with toluene diisocyanate based on high energy ball milling

Energy Technology Data Exchange (ETDEWEB)

Yuan, Yongbing; Chen, Hongling, E-mail: hlchen@njut.edu.cn; Lin, Jinbin; Ji, Yan

2013-11-01

The surface of calcined kaolin particle was modified with toluene diisocyanate (TDI) by using high energy ball milling. The prepared hybrids were characterized by FT-IR, MAS NMR, thermal analysis (TGA-DSC), static water contact angle (CA), apparent viscosity and transmission electron microscopy (TEM). FT-IR and MAS NMR spectra demonstrated that TDI molecules were chemically anchored to kaolin surface after modification. The results of thermal analysis showed that the maximum grafting ratio reached up to 446.61% when the mass ratio of TDI/kaolin was 0.5:1.0, and CA measurements revealed that the resultant hybrids exhibited strong hydrophobicity (148.82°). Apparent viscosity and TEM were employed to examine the dispersion properties of blank and modified kaolin particles in poly (dimenthylsiloxane) matrix. The results illustrated that the dispersion stability depended strongly on the grafting ratio of TDI, neither too low nor too high achieved uniform and stable dispersion, and the favorable grafting ratio was obtained when the mass ratio of TDI/kaolin was 0.2:1.0. Further modification of TDI/kaolin (mass ration of TDI/kaolin, 1.0:1.0) particles with bis(aminopropyl)-terminated-poly(dimethylsiloxane) (APS) was also investigated. TEM evidenced that the dispersion properties of the obtained TDI/APS/kaolin particles were remarkably improved in octamethyl cyclotetrasiloxane compared with the original TDI/kaolin particles.

Why Wet Kaolin can be used as a Crustal Analog and its Application to Fault Evolution at Restraining Bends

Science.gov (United States)

Cooke, M. L.; van der Elst, N.; Schottenfeld, M. T.

2010-12-01

To simulate geologic deformation on observable time and length scales within the lab, a subset of analog modelers have used wet kaolin. Unlike the more often used sand, wet kaolin beautifully exhibits detailed fault structures. Furthermore, faults within the kaolin are more readily reactivated than those in sand. The low plasticity of kaolin (compared to other clays) gives it low shear strength. Consequently, the clay is a suitable analog material if we assume that the wet kaolin deforms by coulomb frictional failure. Koalin generally deforms as a Bingham solid and exhibits more complex deformation than the perfectly plastic behavior assumed with Coulomb failure. We performed fall cone and rheometric tests on wet kaolin to refine our quantitative understanding of its rheology. We use North American wet kaolin with density 1.65-1.7 g/cm3 and water content of 37.5-38.5%. The fall cone tests reveal that the undrained shear strength (100-160 Pa) is greater than previously measured with a viscometer. The rheometer tests show that the wet koalin exhibits many of the same properties of crustal materials including: 1) elastic behavior at low strains, 2) stress relaxation at near-failure strains, 3) creep under static load, 4) yield strength sensitive to strain rate and 5) rate and state dependent failure. Armed with quantitative values for this complex deformation, we can better scale the length and strain rate of the wet koalin experiments to specific crustal settings. Experiments of deformation around restraining bends show features very similar to those found in natural examples. The detailed fault structures produced in the wet kaolin can be analyzed to understand the evolution of active faulting at restraining bends.

1.7.2. The hydrochloric acid decomposition of pre-baked kaolin clays and siallites

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Mirzoev, D.Kh.; Boboev, Kh.E.

2016-01-01

Present article of book is devoted to hydrochloric acid decomposition of pre-baked kaolin clays and siallites. The chemical composition of kaolin clays and siallites was determined. The influence of temperature, process duration, acid concentration on hydrochloric acid decomposition of pre-baked kaolin clays and siallites was studied. The optimal conditions of hydrochloric acid decomposition of pre-baked kaolin clays and siallites were determined.

Soft Soil Improvement for Sub-grade Layer Using Hexagonal Micropiles Layout

Science.gov (United States)

Ambak, K.; Abdullah, N. A. H.; Yusoff, M. F.; Abidin, M. H. Z.

2018-04-01

Soft soil problems are often associated with sediment and stability where it represents a major challenge in Geotechnical Engineering. Research on a soft soil was carried out to determine the level of sediment resulting from the applied load and thus compare the most ideal form of arrangement by the results obtained from bearing capacity. The study was conducted at Research Centre for Soft Soil (RECESS), UTHM by using kaolin. There are several tests conducted on kaolin before the arrangement of pile which is liquid limit test. Through these tests, the level of water content can be maintained which is 1.2 liquid limit where it is in the homogeneous condition. Density test also carried to know weight of kaolin and water that needed in the model. Meanwhile, large strain consolidation test carried on the soil by placing a load of 8 kPa. Then, the pile was arranged in the soil in the shape of a hexagon and square. Load was increased to 12 kPa and imposed on the surface of the pile with a different forms. After 24 hours, the reading of sediment was measured everyday and the process collecting data conducted for 3 week. Based on data obtained, time against sediment can be plotted. To determine the bearing capacity, direct shear test was conducted to get the value coefficient of cohesion, c as a parameter in the calculation of the soil bearing capacity. The results showed that the rate of settlement occurs is different where hexagonal form less the rate of settlement compared to square form which is 64.2% while the results of bearing capacity have the same value.

Preparation and Characterization of Acid and Alkaline Treated Kaolin Clay

Directory of Open Access Journals (Sweden)

Sachin Kumar

2013-06-01

Full Text Available Kaolin was refluxed with HNO3, HCl, H3PO4, CH3COOH, and NaOH of 3M concentration at 110 °C for 4 hours followed by calcination at 550 °C for 2 hours. The physico-chemical characteristics of resulted leached kaolinite clay were studied by XRF, XRD, FTIR, TGA, DTA, SEM and N2 adsorption techniques. XRF and FTIR study indicate that acid treatment under reflux conditions lead to the removal of the octahedral Al3+ cations along with other impurities. XRD of acid treated clay shows that, the peak intensity was found to decrease. Extent of leaching of Al3+ ions is different for different acid/base treatment. The acid treatment increased the Si/Al ratio, surface area and pore volume of the clay. Thus, the treated kaolin clay can be used as promising adsorbent and catalyst supports. © 2013 BCREC UNDIP. All rights reservedReceived: 1st March 2013; Revised: 9th April 2013; Accepted: 19th April 2013[How to Cite: Kumar, S., Panda, A. K., Singh, R.K. (2013. Preparation and Characterization of Acids and Alkali Treated Kaolin Clay. Bulletin of Chemical Reaction Engineering & Catalysis, 8 (1: 61-69. (doi:10.9767/bcrec.8.1.4530.61-69][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.8.1.4530.61-69] |View in  |

Electrical Properties of Zinc-Kaolin Composites below its Percolation ...

African Journals Online (AJOL)

In this paper, we present some electrical properties of the zinc-kaolin cermet resistors with zinc metal fillers below the percolation threshold. Rectangular cermet rods of dimensions 65 mm by 6.5 mm by 3.2 mm were produced in a mould with semi-dry the zinc/kaolin powder mixture which is compressed with a force of about ...

Integrated mined-area reclamation and land-use planning. Volume 3C. A case study of surface mining and reclamation planning: Georgia Kaolin Company Clay Mines, Washington County, Georgia

Energy Technology Data Exchange (ETDEWEB)

Guernsey, J L; Brown, L A; Perry, A O

1978-02-01

This case study examines the reclamation practices of the Georgia Kaolin's American Industrial Clay Company Division, a kaolin producer centered in Twiggs, Washington, and Wilkinson Counties, Georgia. The State of Georgia accounts for more than one-fourth of the world's kaolin production and about three-fourths of U.S. kaolin output. The mining of kaolin in Georgia illustrates the effects of mining and reclaiming lands disturbed by area surface mining. The disturbed areas are reclaimed under the rules and regulations of the Georgia Surface Mining Act of 1968. The natural conditions influencing the reclamation methodologies and techniques are markedly unique from those of other mining operations. The environmental disturbances and procedures used in reclaiming the kaolin mined lands are reviewed and implications for planners are noted.

Technological properties of kaolin from Para; Propriedades tecnologicas do caulin do Para

Energy Technology Data Exchange (ETDEWEB)

Hildebrando, E.; Martin-Cortes, G.R.; Esper, F.J.; Wiebeck, H.; Alves Junior, P.; Valenzuela-Diaz, F.R., E-mail: germac@usp.br [Universidade de Sao Paulo (PMT/EP/USP), Sao Paulo, SP (Brazil). Escola Politecnica. Departamento de Engenharia Metalurgica e de Materiais

2011-07-01

The NE of the State of Para, is notable for its large reserves of kaolin for paper. Kaolin is a mineral composed of hydrated aluminum silicates such as kaolinite and halloysite. The exploitation of these reserves to generate products with higher commercial value, especially in the industries of adsorbents and catalysts, is what motivates the continuous study of technological properties of the Amazon kaolin's. Thus, this paper presents a technological characterization of a sample of kaolin from Para State by X-ray diffraction, SEM - scanning electron microscopy and infrared spectroscopy. The results of preliminary tests indicate that the sample consists for the most part by kaolinite present in low concentrations of quartz and anatase. (author)

A Study on Kaolin and Titanium dioxide affecting Physical Properties of Electrocoating

International Nuclear Information System (INIS)

Yang, Wonseog; Hwang, Woonsuk

2013-01-01

The electrocoating for automotive bodies is pigmented with a mixture of titanium dioxide and kaolin. In this study, the effects of titanium dioxide and kaolin contents in coating on electrodeposition process, drying, and surface properties such as surface roughness, gloss, impact resistance and corrosion resistance were investigated. Titanium dioxide and kaolin in coating do not have a decisive effect on curing reaction during drying and corrosion resistance but on gloss, surface roughness, impact resistance and electrodeposition process of coating. According to its size and shape on coating surface, pigment contents increased during drying process. However, the contents of kaolin and TiO 2 in coating didn't affect the corrosion resistance on zinc phosphated substrate, and the curing properties

Mineralogical characteristics of Cretaceous-Tertiary kaolins of the Douala Sub-Basin, Cameroon

Science.gov (United States)

Bukalo, Nenita N.; Ekosse, Georges-Ivo E.; Odiyo, John O.; Ogola, Jason S.

2018-05-01

As a step in evaluating the quality of Cretaceous-Tertiary kaolins of the Douala Sub-Basin, their mineralogical characteristics were determined. The X-ray diffractometry technique was used to identify and quantify the mineral phases present in bulk and smectite > illite, with mean values of 33.01 > 11.20 > 4.41 wt %; and 72.23 > 10.69 > 4.69 wt %, in bulk and <2 μm fractions, respectively. The kaolins, micromorphologically, consisted of pseudo-hexagonal and thin platy particles; swirl-textured particles; and books or stacks of kaolinite particles. Three main reactions occurred during heating of the kaolins: a low temperature endothermic reaction, observed between 48 and 109 °C; a second low temperature peak, observed between 223 and 285 °C; and a third endothermic peak was found between 469 and 531 °C. In addition, an exothermic reaction also occurred between 943 and 988 °C in some of the samples. The absence of primary minerals such as feldspars and micas in most of these kaolins is an indication of intensive weathering, probably due to the humid tropical climate of the region. The different morphologies suggested that these kaolins might have been transported. Therefore, a humid tropical climate was responsible for the formation of Cretaceous-Tertiary kaolins of the Douala Sub-Basin through intense weathering of surrounding volcanic and metamorphic rocks.

Mineralogical variation in the size fractions of a Ranong kaolin, southern Thailand

Science.gov (United States)

Pisutha-Arnond, Visut; Phuvichit, Suraphol; Leepowpanth, Quanchai

A representative crude Ranong kaolin from the Thungkla-Ranong mine was separated into > 2 mm (granule), 2-1 mm (very coarse sand), 1-0.5 mm (coarse sand), 0.5-0.25 mm (medium sand), 0.25-0.125 mm (fine sand), 0.125-0.062 mm (very fine sand) and 62-28, 28-14, 17-7, 7-4, 4-2, 2-1 and dispersive X-ray spectrometer (EDX). Kaolin group minerals were differentiated by using XRD in combination with various chemical and heat treatments together with TEM, SEM and DTA. The Ranong kaolin consists predominantly of tubular halloysite, poorly crystallized kaolinite and quartz with minor amounts of mica and K-feldspars. Other trace constituents include gibbsite, tourmaline, zircon and colored impurities (i.e. extractable iron hydroxide coating on clay mineral surface). The kaolin minerals are found in all size fractions by which their contents and halloysite/kaolinite ratios increase as the particle sizes become finer. Quartz and mica are also detected in almost all size fractions. They are, however, more abundant with coarsening particle size. Gibbsite, K-feldspar and tourmaline are mainly concentrated in the fine sand to silt size fractions. Crystallinity of kaolin minerals as measured by XRD varied moderately with size. Relatively pure kaolin minerals, predominantly halloysite and kaolinite, can be obtained in the particle size below 1 or 2 μm.

Synthesis and characterization of mesoporous NaY zeolite from natural Blitar’s kaolin

Science.gov (United States)

Khalifah, S. N.; aini, Z. N.; Hayati, E. K.; Aini, N.; Prasetyo, A.

2018-03-01

Mesoporous NaY Zeolite has been synthesized from calcined natural Blitar’s kaolin with the addition of NaOH and CTABr surfactant as mesoporous template by hydrothermal method. Natural kaolin was calcinated with different time and temperature to change kaolin to metakaolin. X-ray diffraction data showed that mesoporous NaY zeolite was formed with impurities compound of sodalite, kaolin and quartz phases. The BET analysis resulted that the pore of NaY Zeolite belongs to mesoporous type with pore size 9,421 nm. Characterization from FTIR confirmed about the functional group of zeolites (988, 776, 663, 464 cm-1). Scanning electron microscopy characterization showed that the morphological of mesoporous NaY zeolites have uniform and crystalline particles formed.

Use of kaolin waste for production os soil-lime blocks

International Nuclear Information System (INIS)

Anjos, C.M. dos; Neves, G.A.

2011-01-01

There is an evident growth in waste generation over the last decades, especially in developing countries. The mining industry produces large quantities and different kinds and levels of dangerousness, such as the kaolin processing industry, which produces waste based on silica, mica and kaolinite. Disposal of this material in an inappropriate location causes significant environmental impacts, which could be minimized with the use of waste as raw material for use in construction. This paper has as main objective to study the incorporation of the kaolin processing waste into soil-lime. The residues of kaolin were calcined at a temperature of 800 ° C for evaluation of pozzolanic activity. Raw materials and conventional alternatives were characterized by means of test particle size analysis by laser diffraction, chemical analysis, X-ray diffraction. Then, blocks conventional soil-lime and soil-lime with the introduction of residual kaolin in proportions of 10%, 20%, 30% and 40% were cast and cured in a moist chamber for periods of 28, 60 and 90 days. The technological tests of compressive strength results obtained within the specifications of the ABNT. The best results were for 90 days of healing and 20% residue. (author)

Statistical treatment of bleaching kaolin by iron removal

Energy Technology Data Exchange (ETDEWEB)

Hernandez H, R. A.; Legorreta G, F.; Hernandez C, L. E. [Universidad Autonoma del Estado de Hidalgo, Area Academica de Ciencias de la Tierra y Materiales, Carretera Pachuca-Tulancingo Km 4.5, Mineral de la Reforma, 42184 Hidalgo (Mexico); Martinez L, A., E-mail: angelitofox3@hotmail.com [Universidad Autonoma de Coahuila, Blvd. V. Carranza y Gonzalez Lobo s/n, 25280 Saltillo, Coahuila (Mexico)

2013-07-01

In the present study, oxalic acid was used as a leaching reagent to remove iron from a kaolin mineral. Statistical analysis was conducted to determine the most influential factors in the dissolution of iron from the kaolin mineral. Our goal was ferric iron solubilization and its reduction to ferrous iron to improve the iron removal in the acid medium. Leaching experiments were conducted at atmospheric pressure. A two-level factorial design of the type 2{sup 4} was utilized. The dependent variable was the percentage of dissolved iron, and the dependent variables in this study were acid concentration (0.35 and 0.50 M), temperature (75 C and 100 C), leaching time (2 and 4 h), and ph (1.5 and 2.5). An analysis of variance revealed that the effects of the factors temperature (b), ph (d), and the combined effects of temperature and time (b c) resulted in the maximum dissolution of iron of 88% at 100 C, giving a kaolin mineral with a whiteness index 93.50. For the mineralogical analysis the X-ray diffraction technique was used. (Author)

Statistical treatment of bleaching kaolin by iron removal

International Nuclear Information System (INIS)

Hernandez H, R. A.; Legorreta G, F.; Hernandez C, L. E.; Martinez L, A.

2013-01-01

In the present study, oxalic acid was used as a leaching reagent to remove iron from a kaolin mineral. Statistical analysis was conducted to determine the most influential factors in the dissolution of iron from the kaolin mineral. Our goal was ferric iron solubilization and its reduction to ferrous iron to improve the iron removal in the acid medium. Leaching experiments were conducted at atmospheric pressure. A two-level factorial design of the type 2 4 was utilized. The dependent variable was the percentage of dissolved iron, and the dependent variables in this study were acid concentration (0.35 and 0.50 M), temperature (75 C and 100 C), leaching time (2 and 4 h), and ph (1.5 and 2.5). An analysis of variance revealed that the effects of the factors temperature (b), ph (d), and the combined effects of temperature and time (b c) resulted in the maximum dissolution of iron of 88% at 100 C, giving a kaolin mineral with a whiteness index 93.50. For the mineralogical analysis the X-ray diffraction technique was used. (Author)

Influence of Sulfonated-Kaolin On Cationic Exchange Capacity Swelling Degree and Morphology of Chitosan/Kaolin Composites

Directory of Open Access Journals (Sweden)

Ozi Adi Saputra

2016-06-01

Full Text Available Preparation of sulfonated-kaolin (sKao has been conducted and used as filler on chitosan matrix via solution casting method, namely chitosan/sKao (Cs/sKao. Swelling degree, cationic exchange capacity and thermal stability were evaluated to determine chitosan/sKao membranes performance as proton exchange membrane in fuel cell. Functional group analysis of chitosan, sKao and synthesized products were studied using Fourier Transform Infra-Red (FTIR spectroscopy. In this study, swelling degree and swelling area of Cs/sKao are also studied to determine of membrane ability to swelling which compare to unmodified chitosan/kaolin (Cs/Kao. The presence of sKao in chitosan matrix was able to improve cationic exchange capacity (CEC which proved by morphological study of membrane surface after CEC test. Moreover, Thermal stability of Cs/sKao showed the membrane has meet requirement for PEM application.

Kaolin in the diet and its effects on performance, litter moisture and intestinal morphology of broiler chickens

Directory of Open Access Journals (Sweden)

Marina Jorge de Lemos

2015-10-01

Full Text Available The objective of this study was to evaluate the effect of the addition of kaolin in the diet on performance, litter moisture and intestinal morphology of broiler chickens. Four hundred ninety-two broiler chickens distributed in a completely randomized design with three treatments and four replicates of 41 birds each, divided into three periods (15-21; 22-34; 35-52 days were used. The following treatments were: Control - reference diet without added kaolin; treatment 1 - reference diet + 0.75% kaolin; Treatment 2 - reference diet + 1.5% kaolin. The variables analyzed were: feed intake, average weight, average weight gain, feed conversion, litter moisture, villus height and crypt depth. The inclusion of kaolin in the diet significantly reduced feed intake, increased weight and average weight gain and improved feed conversion of broilers. The litter moisture decreased significantly after the inclusion of kaolin in the diet. The height of the duodenal villi of broilers increased significantly after inclusion of kaolin, while crypt depth was not influenced. The inclusion 0.75% of kaolin in the diet improved the performance, decreased litter moisture and benefited the intestinal integrity of broilers.

Assembling strategy to synthesize palladium modified kaolin nanocomposites with different morphologies

OpenAIRE

Li, Xiaoyu; Ouyang, Jing; Zhou, Yonghua; Yang, Huaming

2015-01-01

Nanocomposites of aluminosilicate minerals, kaolins (kaolinite and halloysite) with natural different morphologies assembling with palladium (Pd) nanoparticles have been successfully synthesized through strong electrostatic adsorption and chemical bonding after surface modification with 3-aminopropyl triethoxysilane (APTES). Meanwhile, the influence of different morphologies supports on catalytic hydrogenation properties was explored. The surface concentration of amino groups on the kaolins w...

Production and Structural Investigation of Polyethylene Composites with Modified Kaolin

International Nuclear Information System (INIS)

Domka, L.; Malicka, A.; Stachowiak, N.

2008-01-01

The study was undertaken to evaluate the effect of the filler (kaolin) modification with silane coupling agents on the properties of the polyethylene (HDPE Hostalen ACP 5831) composites. Powder mineral fillers are added to polymers to modify the properties of the latter and to reduce the cost of their production. A very important factor is the filler dispersion in the polymer matrix. Kaolin modified with 3-methacryloxypropyltrimethoxysilane and pure kaolin were characterised by surface area, pore size, water absorbing capacity, paraffin oil absorbing capacity, bulk density, scanning electron microscopy observations and X-ray diffraction measurements. Their performance was characterised by determination of the mechanical resistance upon static stretching and tearing, and their structure was observed in scanning electron microscopy images. The results were compared to those obtained for the composites with unmodified filler and pure HDPE. (authors)

Production and Structural Investigation of Polyethylene Composites with Modified Kaolin

Science.gov (United States)

Domka, L.; Malicka, A.; Stachowiak, N.

2008-08-01

The study was undertaken to evaluate the effect of the filler (kaolin) modification with silane coupling agents on the properties of the polyethylene (HDPE Hostalen ACP 5831) composites. Powder mineral fillers are added to polymers to modify the properties of the latter and to reduce the cost of their production. A very important factor is the filler dispersion in the polymer matrix. Kaolin modified with 3-methacryloxypropyltrimethoxysilane and pure kaolin were characterised by surface area, pore size, water absorbing capacity, paraffin oil absorbing capacity, bulk density, scanning electron microscopy observations and X-ray diffraction measurements. Their performance was characterised by determination of the mechanical resistance upon static stretching and tearing, and their structure was observed in scanning electron microscopy images. The results were compared to those obtained for the composites with unmodified filler and pure HDPE.

Sample size clay kaolin of primary in pegmatites regions Junco Serido - PB and Equador - RN

International Nuclear Information System (INIS)

Meyer, M.F.; Sousa, J.B.M.; Sales, L.R.; Silva, P.A.S.; Lima, A.D.D.

2016-01-01

Kaolin is a clay formed mainly of kaolinite resulting from feldspar weathering or hydrothermal. This study aims to investigate the way of occurrence, kaolin particle size of the pegmatites of the Borborema Province Pegmatitic in the regions of Junco do Serido-PB and Ecuador-RN. These variables were analyzed considering granulometric intervals obtained from wet sieving of samples of pegmatite mines in the region. Kaolin was received using sieves of 200, 325, 400 and 500 mesh and the sieve fractions retained by generating statistical parameters histograms. kaolin particles are extremely fine and pass in its entirety through 500 mesh sieve. The characterization of minerals in fine fractions by diffraction of X-rays showed that the relative amount of sericite in fractions retained in sieves 400 and 500 mesh impairing the whiteness and mineralogical texture kaolin production. (author)

Monitoring of Radiation Levels in Mines of Kaolin Located in the Region Serido-PB, Brazil

International Nuclear Information System (INIS)

Guerra Spacov, Isabel Cristina; Dos Santos Amaral, Milton; Araujo dos Santos Junior, Jose

2015-01-01

Kaolin is formed mainly by kaolinite and is used in many industrial sectors. Kaolin may be associated with by-products such as quartz, mica, feldspar and sand. The background radiation from nature is very important, since it represents the main source of human exposure to radiation. In kaolin, radionuclides are present as the 40 K and series 238 U and 232 Th. This study aimed to obtain the rates of effective doses of kaolin mines in the region of Serido-PB, Brazil, where there are several productions and mineral occurrences, including kaolin and uranium at nearby areas. Four kaolin mines located in the Serido-PB region were monitored by a portable discriminator detector NaI(Ti). Measurements were obtained outdoors in triplicate, at a distance of 1.0 meters from the Earth's surface. According to the report of UNSCEAR, the world average effective dose from exposure to natural radiation sources is 2.42 mSvy -1 . the rates of effective doses identified in this study ranged from 1.37 mSvy -1 , and provided the construction of isodose curves. The highest dose rate obtained may be related to pegmatite bodies in a nearby area that contain uranium minerals. However, based on the development of this research, the results indicate that further study in this area is needed in order to infer damage associated with mining of kaolin in the Serido-PB area. (Author)

Synthesis of Zeolite A from Kaolin (Shwe Taung Clay)

International Nuclear Information System (INIS)

Mie Mie Han Htun; Mu Mu Htay

2010-12-01

The synthesis of Zeolite A from locally available kaolin clay (Shwe Taung) in Myanmar has been attempted. The kaolinite was converted to metakaoli, by treating with NaOH at 820C for 1hr, and hydrothermal treatment.It was found that the solution of fused clay powder can be crystallized at 100C under ambient pressure to synthesize Zeolite A. The process variables for synthesis have been optimized in order to produce Zeolite A at a lower price. The mole ratio of SiO2/Al2O3 for kaolin was fixed at 2.54. The effects of various factors (aging time and agitation time) on the structure of the sample were extensively investigated. The Shwe Taung clay was characterized by X-ray Diffraction (XRD), X-ray fluorescence (XRF) and Scanning Electron Microscopy (SEM). The samples were characterized by XRD. The results show that the pure form Zeolite A can be prepared with a molar composition of (2.54 SiO3: Al2O3: 5.8Na2O: 256 H2O) by agitation at room temperature for 30min. The mixture was aged for 24 hour at the same temperature and crystallized at 100C for 48 hour.

Treatment of Waste Lubricating Oil by Chemical and Adsorption Process Using Butanol and Kaolin

Science.gov (United States)

Riyanto; Ramadhan, B.; Wiyanti, D.

2018-04-01

Treatment of waste lubricating oil by chemical and adsorption process using butanol and kaolin has been done. Quality of lubricating oil after treatment was analysis using Atomic Absorption Spectrophotometer (AAS) and Gas Chromatography-Mass Spectrometry (GC-MS). The effects of the treatment of butanol, KOH, and kaolin to metals contain in waste lubricating oil treatment have been evaluated. Treatment of waste lubricating oil has been done using various kaolin weight, butanol, and KOH solution. The result of this research show metal content of Ca, Mg, Pb, Fe and Cr in waste lubricating oil before treatment are 1020.49, 367.02, 16.40, 36.76 and 1,80 ppm, respectively. The metal content of Ca, Mg, Pb, Fe and Cr in the waste lubricating oil after treatment are 0.17, 9.85, 34.07, 78.22 and 1.20 ppm, respectively. The optimum condition for treatment of waste lubricating oil using butanol, KOH, and kaolin is 30 mL, 3.0 g and 1.5 g, respectively. Chemical and adsorption method using butanol and kaolin can be used for decrease of metals contain in waste lubricating oil.

Long-Chain Diacrylate Crosslinkers and Use of PEG Crosslinks in Poly(potassium acrylate-acrylic acid/Kaolin Composite Superabsorbents

Directory of Open Access Journals (Sweden)

Koroush Kabiri

2013-01-01

Full Text Available Long-chain diacrylate crosslinkers based on linear α,ω-diols were synthesized and characterized using FTIR and 1H NMR spectroscopy. The highest reaction yield (99.5% was due to polyethylene glycol diacrylate 1000 (PEGDA-1000. Then, kaolin-containing poly(potassium acrylate-acrylic acid superabsorbent composites and kaolin-free counterparts were synthesized using PEGDA-1000.The effect of the crosslinker concentration on swelling, rheological and thermo-mechanical properties was investigated. Absorption capacity of the composite hydrogels (having ~38% kaolin was unexpectedly higher than that of kaolin-free hydrogels. This was attributed to an interfering effect of kaolin during the polymerization. Glass transition temperature was increased with crosslinker concentration enhancement and addition of kaolin up to about 10oC and 28oC, respectively. Making such K-containing superabsorbents may be taken as an effective action to achieve more durable and cheaper superabsorbents for agricultural uses.

Side effects of kaolin particle films on apple orchard bug, beetle and spider communities

NARCIS (Netherlands)

Marko, V.; Bogya, S.; Kondorosy, E.; Blommers, L.H.M.

2010-01-01

The effects of multiple applications of hydrophobic kaolin particle film on apple orchard bug (Heteroptera), beetle (Coleoptera) and spider (Araneae) assemblages were studied in the Netherlands. Insecticide-free orchard plots served as a control. The kaolin applications significantly reduced the

Kaolin Quality Prediction from Samples: A Bayesian Network Approach

International Nuclear Information System (INIS)

Rivas, T.; Taboada, J.; Ordonez, C.; Matias, J. M.

2009-01-01

We describe the results of an expert system applied to the evaluation of samples of kaolin for industrial use in paper or ceramic manufacture. Different machine learning techniques - classification trees, support vector machines and Bayesian networks - were applied with the aim of evaluating and comparing their interpretability and prediction capacities. The predictive capacity of these models for the samples analyzed was highly satisfactory, both for ceramic quality and paper quality. However, Bayesian networks generally proved to be the most useful technique for our study, as this approach combines good predictive capacity with excellent interpretability of the kaolin quality structure, as it graphically represents relationships between variables and facilitates what-if analyses.

Facile Selective and Diverse Fabrication of Superhydrophobic, Superoleophobic-Superhydrophilic and Superamphiphobic Materials from Kaolin.

Science.gov (United States)

Qu, Mengnan; Ma, Xuerui; He, Jinmei; Feng, Juan; Liu, Shanshan; Yao, Yali; Hou, Lingang; Liu, Xiangrong

2017-01-11

As the starting material, kaolin is selectively and diversely fabricated to the superhydrophobic, superoleophobic-superhydrophilic, and superamphiphobic materials, respectively. The wettability of the kaolin surface can be selectively controlled and regulated to different superwetting states by choosing the corresponding modification reagent. The procedure is facile to operate, and no special technique or equipment is required. In addition, the procedure is cost-effective and time-saving and the obtained super-repellent properties are very stable. The X-ray photoelectron spectroscopy analysis demonstrates different changes of kaolin particles surfaces which are responsible for the different super-repellency. The scanning electron microscopy displays geometric micro- and nanometer structures of the obtained three kinds of super-repellent materials. The results show that kaolin has good applications in many kinds of superwetting materials. The method demonstrated in this paper provides a new strategy for regulating and controlling the wettability of solid surfaces selectively, diversely, and comprehensively.

Infrared detection of the mineralogical aspects that influence the processing of calcined kaolin

Science.gov (United States)

Groenheide, Stefan; Guatame-Garcia, Adriana; Buxton, Mike; van der Werff, Harald

2017-04-01

Calcined kaolin is an industrial minerals product used in the production of paper, paint, rubber and other specialty applications. It is produced from kaolinite through a series of refinement steps and final calcination at temperatures of above 900°C, with the aim of generating a whiter and more abrasive material. The raw kaolin ore is a mixture of clay minerals, quartz and feldspars, where kaolinite is the main constituent. The optimal kaolin ores to feed the processing plant should ideally have high kaolinite abundance, be free in Fe-bearing mineralogy (to avoid influence in the colour of the product), and the kaolinite itself should be of high crystallinity (to ensure the correct abrasiveness after calcination). This work presents a case study from the kaolin deposits in the St. Austell Granite (South-West England), which are known for their high quality and world-class size. In this area, the kaolin is of primary-hydrothermal origin, with mineral associations that are related to the genetic history. The eventual depletion of the high-quality reserves is bringing now the attention to the lower grade zones, where the amount of impurities increases. As a consequence, it is critical to developing strategies that ensure the supply of high-quality ore to the processing plant. For this, it is necessary to acquire a thorough knowledge of the ore, including relative abundance of the minerals and their textural relationships. Hyperspectral images in the visible-near infrared (VNIR) and short-wave infrared (SWIR) ranges were collected from drill cores and run-off-mine (ROM) samples, obtained from one of the kaolin pits in the St. Austell area, where the kaolin quality is known to be lower than in the rest of the deposit. A series of mineral maps were generated to assess the distribution, texture and abundance of the Fe-bearing mineralogy and the other kaolin-associated minerals, as well as the variations in the crystallinity of kaolinite. The mineral maps enabled the

Mineralogical association in the zone of argillic advanced alteration in a kaolin deposit of Patagonia Argentina

International Nuclear Information System (INIS)

Rainoldi, A; Oviedo, P.; Maiza, P.; Marfil, S.

2010-01-01

This work is about the mineralogical and petrological relations of the para genetic association of advanced argillic zone in the kaolin deposit in Patagonia.This study allowed to establish the sequence of events that took place in the deposit as well as the conditions under which they were generated

Recent development of high gradient superconducting magnetic separator for kaolin in China

Energy Technology Data Exchange (ETDEWEB)

Zhu, Zian; Wang, Meifen; Ning, Fei Peng; Yang, Huan; Zhang, Guoqing; Hou, Zhi Long; Liu, Zhaong Xiu; Dai, Zhong [Institute of High Energy Physics and University of Chinese Academy of Sciences, Beijing (China); Li, Pei Yong; Zhang, Yiting; Wang, Zhaolian [Weifang Xinli Superconducting Technology Co.,Ltd., Weifang (China)

2017-03-15

A series of high gradient superconducting magnetic separator (HGMS) for kaolin has been developed. It is used for processing kaolin to increase the brightness or whiteness whether it is for paper or ceramic applications. The HGMS system mainly consists of a solenoid magnet with a zero boil-off helium cryostat, a double reciprocating canisters system, and a PLC (Process Logic Controller) fully automatic control system based on SCADA (Supervisory Control and Data Acquisition) system. We have successfully developed CGC-5.5/300 and CGC-5.0/500 HGMS systems in the recent years, and now three sets of them are on-site operation in different customers. This paper will present recent progress of the HGMS system, the results of some experiments on processing kaolin clay used HGMS, and the on-site operation.

Recent development of high gradient superconducting magnetic separator for kaolin in China

International Nuclear Information System (INIS)

Zhu, Zian; Wang, Meifen; Ning, Fei Peng; Yang, Huan; Zhang, Guoqing; Hou, Zhi Long; Liu, Zhaong Xiu; Dai, Zhong; Li, Pei Yong; Zhang, Yiting; Wang, Zhaolian

2017-01-01

A series of high gradient superconducting magnetic separator (HGMS) for kaolin has been developed. It is used for processing kaolin to increase the brightness or whiteness whether it is for paper or ceramic applications. The HGMS system mainly consists of a solenoid magnet with a zero boil-off helium cryostat, a double reciprocating canisters system, and a PLC (Process Logic Controller) fully automatic control system based on SCADA (Supervisory Control and Data Acquisition) system. We have successfully developed CGC-5.5/300 and CGC-5.0/500 HGMS systems in the recent years, and now three sets of them are on-site operation in different customers. This paper will present recent progress of the HGMS system, the results of some experiments on processing kaolin clay used HGMS, and the on-site operation

PHYSICAL PROPERTIES OF KAOLIN/SAND SLURRY USED DURING SUBMERSIBLE MIXER PUMP TESTS AT TNX

International Nuclear Information System (INIS)

HANSEN, ERICH

2005-01-01

The purpose of this task is to characterize the physical properties of the kaolin/sand slurries used during the testing of a new submersible mixer pump (SMP) which had undergone performance testing at the TNX Waste Tank mockup facility from July 2004 through May 2005. During this time period, four identical SMPs were subjected to various water tests and four different tests using different batches of kaolin/sand slurries. The physical properties of the kaolin/sand slurries were measured for three of the four tests. In these tests, three different sample locations were used to pull samples, the SMP cooling water exit (CWE), the SMP fluid flow field (FFF), and SMP effective cleaning radius (ECR). The physical properties measured, though not for each sample, included rheology, weight percent total solids (wt% TS), density, kaolin/sand slurry particle size distribution (PSD), weight percent and particles size distribution of material greater than 45 microns

Comparing Kaolin and Pinolene to Improve Sustainable Grapevine Production during Drought.

Science.gov (United States)

Brillante, Luca; Belfiore, Nicola; Gaiotti, Federica; Lovat, Lorenzo; Sansone, Luigi; Poni, Stefano; Tomasi, Diego

2016-01-01

Viticulture is widely practiced in dry regions, where the grapevine is greatly exposed to water stress. Optimizing plant water use efficiency (WUE) without affecting crop yield, grape and wine quality is crucial to limiting use of water for irrigation and to significantly improving viticulture sustainability. This study examines the use in vineyards of particle film technology (engineered kaolin) and compares it to a film-forming antitranspirant (pinolene), traditionally used to limit leaf water loss, and to an untreated control. The trial was carried out under field conditions over three growing seasons, during which moderate to very severe plant water stress (down to -1.9 MPa) was measured through stem water potential. Leaf stomatal conductance (gs) and photosynthesis rate (An) were measured during the seasons and used to compute intrinsic WUE (WUEi, defined as An/gs ratio). Leaf temperature was also recorded and compared between treatments. Bunch quantity, bunch and berry weight, sugar accumulation, anthocyanin and flavonoid contents were measured. Finally, microvinifications were performed and resultant wines subjected to sensory evaluation.Results showed that the use of kaolin increased grapevine intrinsic WUE (+18% on average as compared to unsprayed vines) without affecting berry and bunch weight and quantity, or sugar level. Anthocyanin content increased (+35%) in kaolin treatment, and the wine was judged more attractive (p-value wine was the least appreciated. This study demonstrates that particle film technology can improve vine WUEi and wine quality at the same time, while traditional antitranspirants were not as effective for these purposes. This positive effect can be used in interaction with other already-demonstrated uses of particle film technology, such as pest control and sunburn reduction, in order to achieve more sustainable vineyard management.

Flotation of kaolinite from tailings of kaolin-washing plants by cationic collectors

OpenAIRE

Barani Kianoush

2016-01-01

Traditional processing of kaolin is achieved by dispersion of the mined ore and classification by means of multistage hydrocyclones. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back to the quarry. In this research recovery of kaolinite from tailings of the Zonoupz kaolin washing plant, which is located in Iran, was investigated by cationic flotation. Flotation experiments showed that flotation of kaolinite from tailings was much better in an ac...

Evaluation of The Use of Bentonite, Kaolin and Feldspar For Immobilizing The Uranium Radionuclide Slugdewaste

International Nuclear Information System (INIS)

Prayitno

2006-01-01

The experimental investigation on the mixture of bentonite, kaolin, feldspar, sludge waste and with the ratio of bentonite, kaolin, feldspar for evaluating its effectiveness has been done. Experimentally, this investigation is the preliminary study of the use of bentonite, kaolin, feldspar as a material for the immobilization of sludge waste containing material element especially uranium. This investigation was conducted by mixing waste (2,5; 5; 7.5; 10; 12.5 and 15 %) of total weight sludge waste and bentonite, kaolin, feldspar with of 800, 900 and 1000 o C temperature. The obtained the process condition in which the uranium fraction immobilized could be kept in the limit of safety standard for the sludge waste. Therefore, it could be concluded that the addition of hay ash as an additive in the formation of block monolith tend to minimize the leached sludge waste in the leaching media. (author)

Bacterial cellulose–kaolin nanocomposites for application as biomedical wound healing materials

International Nuclear Information System (INIS)

Wanna, Dwi; Alam, Parvez; Alam, Catharina; Toivola, Diana M

2013-01-01

This short communication provides preliminary experimental details on the structure–property relationships of novel biomedical kaolin–bacterial cellulose nanocomposites. Bacterial cellulose is an effective binding agent for kaolin particles forming reticulated structures at kaolin–cellulose interfaces and entanglements when the cellulose fraction is sufficiently high. The mechanical performance of these materials hence improves with an increased fraction of bacterial cellulose, though this also causes the rate of blood clotting to decrease. These composites have combined potential as both short-term (kaolin) and long-term (bacterial cellulose) wound healing materials. (paper)

PES-Kaolin Mixed Matrix Membranes for Arsenic Removal from Water.

Science.gov (United States)

Marino, Tiziana; Russo, Francesca; Rezzouk, Lina; Bouzid, Abderrazak; Figoli, Alberto

2017-09-30

The aim of this work was the fabrication and the characterization of mixed matrix membranes (MMMs) for arsenic (As) removal from water. Membrane separation was combined with an adsorption process by incorporating the kaolin (KT2) Algerian natural clay in polymeric membranes. The effects of casting solution composition was explored using different amounts of polyethersufone (PES) as a polymer, polyvinyl-pyrrolidone (PVP K17) and polyethylene glycol (PEG 200) as pore former agents, N -methyl pyrrolidone (NMP) as a solvent, and kaolin. Membranes were prepared by coupling Non-solvent Induced Phase Separation and Vapour Induced Phase Separation (NIPS and VIPS, respectively). The influence of the exposure time to controlled humid air and temperature was also investigated. The MMMs obtained were characterized in terms of morphology, pore size, porosity, thickness, contact angle and pure water permeability. Adsorption membrane-based tests were carried out in order to assess the applicability of the membranes produced for As removal from contaminated water. Among the investigated kaolin concentrations (ranging from 0 wt % to 5 wt %), a content of 1.25 wt % led to the MMM with the most promising performance.

Effect of the rate of calcination of kaolin on the properties of metakaolin-based geopolymers

Directory of Open Access Journals (Sweden)

B.B. Kenne Diffo

2015-03-01

Full Text Available Kaolin samples of the same mass were treated at 700 °C for the same duration of 30 min by varying the rate of calcination (1, 2.5, 5, 10, 15 and 20 °C/min in order to obtain metakaolins which were used to produce geopolymers. Depending on the nature of each type of material, kaolin, metakaolins and geopolymers were characterized using thermal analysis, chemical analysis, XRD, FTIR, particle size distribution, specific surface area, bulk density, setting time and compressive strength. FTIR and XRD analyses showed that metakaolins except at 1 °C/min contained residual kaolinite whose quantity increased with the rate of calcination of kaolin and which influenced the characteristics of geopolymers. Thus as the rate of calcination of kaolin increased, the setting time increased (226 min (rate of 1 °C/min–773 min (rate of 20 °C/min while the compressive strength reduced (49.4 MPa (rate of 1 °C/min–20.8 MPa (rate of 20 °C/min. From the obtained results the production of geopolymers having high compressive strength along with low setting time requires that the calcination of kaolin be carried out at a low rate.

Microstructural analysis of ceramic masses with waste kaolin addition for the red ceramic production

International Nuclear Information System (INIS)

Vida, Talita Almeida; Fagury Neto, Elias; Rabelo, Adriano Alves

2010-01-01

Incorporating reject industrial ceramic mixtures has proved viable in the reduction of environmental liabilities. In this study, we sought to study the potential use of ceramic formulations with the addition of tailings from the production of kaolin clay to the region of the city of Maraba-PA. Formulations were obtained with two clays of this region with the addition of up to 60% by weight of kaolin waste. The microstructural analyses were carried out from the preparation of specimens that were sintered at 1000 and 1200 °C with level 3 hours. The samples prepared were used to observe the microstructure by optical microscope, to determine the constituents of each formulation after burning. And later analysis was performed X-rays diffraction, to quantify the phases present. It was observed that increasing the content of the mixture of kaolin clay caused the reaction of kaolinite forming the primary mullite from 1000 ° C. For a firing temperature around 1200 ° C showed the presence of mullite even the addition of 20% kaolin, noting also the presence of secondary kaolinite. (author)

Assessment of the adsorptive capacity of the Kaolin deposit targeting its use on the removal of colors in aqueous solution

International Nuclear Information System (INIS)

Matos, S.C.; Hildebrando, E.A.

2016-01-01

The Amazonic region has large and valuable kaolin deposits. The state of Para by itself comprises three large industries which process kaolin. It has been noticed that the waste resulting from the processing of kaolin is rich in silico-aluminate, presenting potential in adsorption processes. Thus, this research's objective is to assess the kaolin waste produced during the processing phase, aiming at its application as low cost adsorbent material. For that, the kaolin waste has been characterized by X-ray diffraction and chemical analysis (XRF), and then sieved and calcined at 700 ° C, being then subjected to the adsorption process and observed qualitatively its capacity of retention by methylene blue (AM). Preliminary results show that the kaolin waste has satisfactory adsorption capacity at concentrations of up to 50.0 mg / MP, demonstrating the potential that it be used in the removal of dyes in wastewater treatment. (author)

Characterization of kaolin wastes from kaolin mining industry from the amazon region as raw material for pozzolans production; Caracterizacao dos residuos cauliniticos das industrias de mineracao de caulim da amazonia como materia-prima para producao de pozolanas de alta reatividade

Energy Technology Data Exchange (ETDEWEB)

Barata, M.S.; Angelica, R.S., E-mail: msb@amazon.com.br, E-mail: angelica@ufpa.br [Instituto de Geociencias, Universidade Federal do Para, Belem, PA (Brazil)

2012-01-15

Capim and Jari are the two most important kaolin mining districts of the Brazilian Amazon region. They encompass the major Brazilian reserves of high quality kaolin for the paper coating industry. The kaolin is mined and processed by three major companies responsible for about 500,000 ton of a residue mainly composed of kaolinite. The wastes come mainly from the centrifugation phase of the kaolin beneficiation process and their final destinations are huge sedimentation basins that occupy large areas. The main purpose of this work is to evaluate the physical, chemical and mineralogical characteristics of the kaolin wastes processed from the Capim and Jari region, in order to obtain meta kaolinite, a high reactive pozzolans for the cement industry. When incorporated to ordinary Portland cement such pozzolans increases the concrete and mortars performance. All the residues studied in this work were characterized by means of: X-ray diffraction analysis, differential thermal analysis, infrared spectroscopy, scanning electron microscopy, X-ray fluorescence spectrometry and laser diffraction. Both residues are mainly constitutes by at least 92% of low granulometry kaolinite with specific surface area above 8 m2 /g and mean diameter below 1 {mu}m. Free silica (quartz) contents are below 3%. The high concentration of kaolinite in these residues dispenses rigid control parameters for removal of impurities usually employed in pozzolans production. The Jari kaolin exhibits high disordered kaolinite in comparison with the high ordered kaolinite of the Capim region and gives rise to higher desidroxilation degree at lower temperatures. It points to energy saving and reducing costs during the production of a pozzolans. The results are satisfactory and reveal that both kaolin wastes are excellent raw material for the production of high reactive meta kaolin. (author)

Kaolin from Acoculco (Puebla, Mexico) as a raw material: mineralogical and thermal characterization

OpenAIRE

Garcia Vallès, Maite; Pi, T.; Alfonso, P.; Canet, C.; Martínez Manent, Salvador; Jiménez-Franco, A.; Tarragó Aymerich, Mariona; Hernández-Cruz, B.

2015-01-01

The present study determined the mineralogy and thermal properties of kaolin from Acoculco (Puebla), at the eastern Trans-Mexican Volcanic Belt and compared it with the nearby deposits of Agua Blanca (Hidalgo) and Huayacocotla (Veracruz). The mineralogy of the kaolins was determined by X-ray diffraction, infrared spectroscopy and scanning electron microscopy. Thermal behaviour was studied by differential thermal analysis, dilatometry and hot-stage microscopy. The Acoculco deposit is composed ...

Physicochemical Evaluation of Industrial Potentialities of Getso Kaolin

African Journals Online (AJOL)

2017-08-13

Aug 13, 2017 ... manufacturing sector. In this study kaolin from Getso, Kano state, northern part of Nigeria was characterized ... foreign import, leaving a supply gap of over. 250,000 .... the presence of mica; the strong band at 3694 cm-1. 80.53.

Contemporary technology of enrichment of Angren deposit of kaolins. I. Using a ultrasonic dispersion for shallowing of raw materials

International Nuclear Information System (INIS)

Krivorotov, V.F.; Usmanov, Zh.M.; Fridman, A.A.

2012-01-01

Optimal parameters of ultrasonic dispersion at enrichment of Angren kaolins are presented. It has been stated that the granule sizes of the kaolin-powder produced by this technology are 0.15-4.0 μm, and 75% of particles have sizes 0.15-1.5 μm. The whiteness of the kaolin-powder amounts 80 - 82%. (authors)

Linear luminescence for thin plastic scintillator under intense soft X-ray irradiation

International Nuclear Information System (INIS)

Ning Jiamin; Jiang Shilun; Xu Rongkun; Guo Cun

2006-01-01

The basic principle of soft X-ray power meter is introduced in the paper and the experimental process and the result of thin plastic scintillator linear luminescence under intense soft X-ray irradiation are described. A range of flux density of energy for thin plastic scintillator linear luminescence under intense soft X-ray irradiation is included. The upper limit of the flux density is 1.47 x 10 5 W/cm 2 . (authors)

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production

International Nuclear Information System (INIS)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de

2016-01-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Novel kaolin/polysiloxane based organic-inorganic hybrid materials: Sol-gel synthesis, characterization and photocatalytic properties

Science.gov (United States)

dos Reis, Glaydson Simões; Lima, Eder Cláudio; Sampaio, Carlos Hoffmann; Rodembusch, Fabiano Severo; Petter, Carlos Otávio; Cazacliu, Bogdan Grigore; Dotto, Guillherme Luiz; Hidalgo, Gelsa Edith Navarro

2018-04-01

New hybrid materials using kaolin and the organosilicas methyl-polysiloxane (MK), methyl-phenyl-polysiloxane (H44), tetraethyl-ortho-silicate (TEOS) and 3-amino-propyl-triethoxysilane (APTES) were obtained by sol-gel process. These materials presented specific surfaces areas (SBET) in the range of 20-530 m2 g-1. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed remarkable differences between the kaolin and hybrid structures. Thermogravimetric analysis (TGA) revealed that the hybrid materials presented higher thermal stability when compared with their precursors. The electronic properties of the materials were also studied by Ultraviolet-Visible Diffuse Reflectance Absorption (DRUV) and Diffuse Reflectance spectroscopy (DR), where a new absorption band was observed located around 400-660 nm. In addition, these materials exhibit a decrease in DR from 30% to 70% in the blue-cyan green region and are significantly more transparent in the UV region than the kaolin, which could be useful for photocatalysis applications. These results show that the electronic structure of the final material was changed, indicating a significant interaction between the kaolin and the respective silica derivative. These findings support the main idea of the hybridization afforded by pyrolysis between kaolin and organosilica precursors. In addition, as a proof of concept, these hybrid materials were successfully employed as photocatalyst in the photoreduction of Cr(VI) to Cr(III).

Facile Fabrication of a Hierarchical Superhydrophobic Coating with Aluminate Coupling Agent Modified Kaolin

OpenAIRE

Hui Li; Mengnan Qu; Zhe Sun; Jinmei He; Anning Zhou

2013-01-01

A superhydrophobic coating was fabricated from the dispersion of unmodified kaolin particles and aluminate coupling agent in anhydrous ethanol. Through surface modification, water contact angle of the coating prepared by modified kaolin particles increased dramatically from 0° to 152°, and the sliding angle decreased from 90° to 3°. Scanning electron microscopy was used to examine the surface morphology. A structure composed of micro-nano hierarchical component, combined with the surface modi...

Flotation of kaolinite from tailings of kaolin-washing plants by cationic collectors

Directory of Open Access Journals (Sweden)

Barani Kianoush

2016-01-01

Full Text Available Traditional processing of kaolin is achieved by dispersion of the mined ore and classification by means of multistage hydrocyclones. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back to the quarry. In this research recovery of kaolinite from tailings of the Zonoupz kaolin washing plant, which is located in Iran, was investigated by cationic flotation. Flotation experiments showed that flotation of kaolinite from tailings was much better in an acidic than in an alkaline medium containing cationic collectors.

Geology and industrial mineral resources of the Macon-Gordon Kaolin District, Georgia

Science.gov (United States)

Buie, Bennett Frank; Hetrick, J.H.; Patterson, S.H.; Neeley, C.L.

1979-01-01

The Macon-Gordon kaolin district is about 80 miles (130 km) southeast of Atlanta, Georgia. It extends across the boundary between, and includes parts of, the Piedmont and Atlantic Coastal Plain physiographic provinces. The rocks in the Piedmont are mainly intensely folded sericite schist and granite gneiss containing irregular masses of amphibolite and feldspathic biotite gneiss and scattered igneous intrusive rocks. Most of the crystalline rocks are thought to be of Paleozoic age, but some of the intrusive rocks may be younger. The crystalline rocks are cut by a major unconformity and are overlain by sedimentary formations ranging in age from Cretaceous to Miocene. The valuable kaolin deposits occur in the Cretaceous beds, undivided, and in the Huber Formation which is of Paleocene to middle Eocene age. The resources of kaolin in the district are estimated in millions of metric tons as follows: reserves, 100; subeconomic resources, 700 to 900; undiscovered resources, probably 700 to 1,000. In addition to kaolin, the leading mineral commodity mined in the district, crushed stone and sand are now being produced, and fuller's earth and a minor amount of limestone were formerly produced. The crushed stone is quarried from igneous rocks in the Piedmont province. The sand is washed from the Cretaceous beds, undivided. The fuller's earth was mined from the Twiggs Clay Member of the Barnwell Formation, and limestone was dug from the Tivola Limestone.

CERAMIC PROPERTIES OF PUGU KAOLIN CLAYS. PART 2 ...

African Journals Online (AJOL)

a

PART 2: EFFECT OF PHASE COMPOSITION ON FLEXURAL STRENGTH ... working in this field have established factors controlling the various ... The raw materials selected were kaolin clays from Pugu deposit in Tanzania, Norfloat potash .... the total mullite contents present in the samples since the method used does.

Experiment study on the thermal properties of paraffin/kaolin thermal energy storage form-stable phase change materials

International Nuclear Information System (INIS)

Lv, Peizhao; Liu, Chenzhen; Rao, Zhonghao

2016-01-01

Highlights: • Different particle sizes of kaolin were employed to load paraffin. • The effects and reasons of particle size on thermal conductivity were studied. • Thermal property and thermal stability of the composites were investigated. • The leakage and thermal storage and release rate of the composites were studied. • The effect of vacuum impregnation method on thermal conductivity was investigated. - Abstract: In this paper, different particle sizes of kaolin were employed to incorporate paraffin via vacuum impregnation method. The paraffin/kaolin composites were characterized by Scanning Electron Microscope (SEM), X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimeter (DSC) and Thermogravimetry (TG). The results showed that the paraffin/kaolin composite with the largest particle size of kaolin (K4) has the highest thermal conductivity (0.413 W/(m K) at 20 °C) among the diverse composites. The latent heat capacity of paraffin/K4 is 119.49 J/g and the phase change temperature is 62.4 °C. In addition, the thermal properties and thermal conductivities of paraffin/K4 with different mass fraction of K4 (0–60%) were investigated. The thermal conductivities of the composites were explained in microcosmic field. The phonon mean free path determines the thermal conductivity, and it can be significantly affected by temperature and the contact surface area. The leaks, thermal storage and release properties of pure paraffin and paraffin/kaolin composites were investigated and the composites presented good thermal stabilities.

Evaluation of the potential of waste processing of secondary kaolin of Para for use in porcelain

International Nuclear Information System (INIS)

Junior, V.G.L.; Fernandes, L.L.; Fagury Neto, E.; Rabelo, A.A.

2012-01-01

The kaolin waste evaluated is characterized as secondary due be coming from the steps of centrifugation, magnetic separation, bleaching and filtering, which gives a ratio which provides a significant residue, about 26% of their gross, that is intended for embankments. This study aimed to evaluate the potential of reusing the kaolin waste processing from Imerys RCC in the region of Barcarena (PA) in formulation of ceramic bodies for porcelain tiles production, seeking to property of maximum water absorption of 0.5 % for this type of product. The residue from the production of kaolin had been previously characterized by X-ray diffraction and there is a significant amount of kaolinite concentration. After the ceramic processing to obtain the test specimens with different amounts of residue replacing the kaolin, these were sintered using 1200, 1220 and 1240 °C for 2 hours. The formulations were evaluated by water absorption, linear firing shrinkage and modulus of rupture at a three-point bending setup of the pieces produced. (author)

Characterization of kaolin dispersion using acoustic and electroacoustic spectroscopy

Directory of Open Access Journals (Sweden)

Dohnalová Ž.

2008-01-01

Full Text Available The objective of this work is the investigation of the kaolin dispersion by the ultrasonic techniques. In contact with aqueous solution clay minerals show cation - exchange properties and certain degree of dissolution or rather selective leaching of components. The work is divided into two main parts - determination of zeta potential and particle size distribution. The first part is focused on measuring of zeta potential. Effects of concentration of solid, different kind of electrolytes (0.01 M KCl, 0.01 M MgCl2 and 0.01 M CaCl2, pH and temperature of the dispersions are investigated. The isoelectric points (IEP of kaolin suspension are about pH 4-5. Electrolytes containing monovalent cations such as K+ become zeta potential more negative compared to the values obtained with water. Such behavior is explained by the exchange of K+ ions with H+ ions in the system. When the electrolyte is formed by divalent cations such as Mg2+ or Ca2+, the values of zeta potential become less negative than zeta potential of kaolin in water. The second part is focused on the determination of particle size distribution with respect to dispersing conditions, such as the optimal dispersing agent (Na2SiO3, (NaPO36, Na4P2O7 or Busperse, time and power of ultrasonication and also the tracking of dispersion stability that is expressed by the measuring of particle size distribution during certain time period.

Comparing Kaolin and Pinolene to Improve Sustainable Grapevine Production during Drought.

Directory of Open Access Journals (Sweden)

Luca Brillante

Full Text Available Viticulture is widely practiced in dry regions, where the grapevine is greatly exposed to water stress. Optimizing plant water use efficiency (WUE without affecting crop yield, grape and wine quality is crucial to limiting use of water for irrigation and to significantly improving viticulture sustainability. This study examines the use in vineyards of particle film technology (engineered kaolin and compares it to a film-forming antitranspirant (pinolene, traditionally used to limit leaf water loss, and to an untreated control. The trial was carried out under field conditions over three growing seasons, during which moderate to very severe plant water stress (down to -1.9 MPa was measured through stem water potential. Leaf stomatal conductance (gs and photosynthesis rate (An were measured during the seasons and used to compute intrinsic WUE (WUEi, defined as An/gs ratio. Leaf temperature was also recorded and compared between treatments. Bunch quantity, bunch and berry weight, sugar accumulation, anthocyanin and flavonoid contents were measured. Finally, microvinifications were performed and resultant wines subjected to sensory evaluation.Results showed that the use of kaolin increased grapevine intrinsic WUE (+18% on average as compared to unsprayed vines without affecting berry and bunch weight and quantity, or sugar level. Anthocyanin content increased (+35% in kaolin treatment, and the wine was judged more attractive (p-value <0.05 and slightly more appreciated (p-value < 0.1 than control. Pinolene did not increase WUEi, limiting An more than gs; grapes with this treatment contained lower sugar and anthocyanin content than control, and the obtained wine was the least appreciated. This study demonstrates that particle film technology can improve vine WUEi and wine quality at the same time, while traditional antitranspirants were not as effective for these purposes. This positive effect can be used in interaction with other already

Application Of Bacterial Iron Reduction For The Removal Of Iron Impurities From Industrial Silica Sand And Kaolin

Science.gov (United States)

Zegeye, A.; Yahaya, S.; Fialips, C. I.; White, M.; Manning, D. A.; Gray, N.

2008-12-01

Biogeochemical evidence exists to support the potential importance of crystalline or amorphous Fe minerals as electron acceptor for Fe reducing bacteria in soils and subsurface sediments. This microbial metabolic activity can be exploited as alternative method in different industrial applications. For instance, the removal of ferric iron impurities from minerals for the glass and paper industries currently rely on physical and chemical treatments having substantial economical and environmental disadvantages. The ability to remove iron by other means, such as bacterial iron reduction, may reduce costs, allow lower grade material to be mined, and improve the efficiency of mineral processing. Kaolin clay and silica sand are used in a wide range of industrial applications, particularly in paper, ceramics and glass manufacturing. Depending on the geological conditions of deposition, they are often associated with iron (hydr)oxides that are either adsorbed to the mineral surfaces or admixed as separate iron bearing minerals. In this study, we have examined the Fe(III) removal efficiency from kaolin and silica sand by a series of iron- reducing bacteria from the Shewanella species (S. alga BrY, S. oneidensis MR-1, S. putrefaciens CN32 and S. putrefaciens ATCC 8071) in the presence of anthraquinone 2,6 disulfonate (AQDS). We have also investigated the effectiveness of a natural organic matter, extracted with the silica sand, as a substitute to AQDS for enhancing Fe(III) reduction kinetics. The microbial reduction of Fe(III) was achieved using batch cultures under non-growth conditions. The rate and the extent of Fe(III) reduction was monitored as a function of the initial Fe(III) content, Shewanella species and temperature. The bacterially- treated minerals were analyzed by transmission electron microscopy (TEM) and X-ray diffraction (XRD) to observe any textural and mineralogical transformation. The whiteness and ISO brightness of the kaolin was also measured by

Nibelung-Kaoline-Black band fluit clay - the new key-horizon in the carboniferous system of the Ruhr coal field

Energy Technology Data Exchange (ETDEWEB)

Burger, K.; Otte, M.U. (Bergbau A.G. Lippe, Gelsenkirchen (Germany, F.R.). Abt. Markscheidewesen); Pfisterer, W. (Bergbau A.G. Lippe, Herne (Germany, F.R.). Hauptlaboratorium)

1979-10-01

Based upon the stratigraphic distribution of the kaoline-black-band flint clay in the carbon strata of the Ruhr, the Nibelung-Kaoline-black-band flint clay found in the upper Westphal C (Dorsten strata) is defined to be the new keyhorizon. The position of the discoveries of the kaoline-black-band flint clay, its stratigraphic positions as well as its macroscopic and microscopic characteristics together with the chemical composition are given. Investigations of the structure and minerals content show that the Nibelung-Kaolin-black-band flint clay is a new keyhorizon and is of great importance for the stratigraphy of the upper Westfal C. Its position within the system is represented by strata sections.

Potassium Capture by Kaolin, Part 2: K2CO3, KCI, and K2SO4

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2018-01-01

residence time on the reaction was investigated. The results showed that the K-capture level (C-K) (g potassium reacted by per g kaolin available) of K2CO3 and KCI by kaolin generally followed the equilibrium predictions at temperatures above 1100 degrees C, when using a kaolin particle size of D50 = 5.......47 mu m and a residence time of 1.2 s. This revealed that a nearly full conversion was obtained without kinetic or transport limitations at the conditions applied. At 800 and 900 degrees C, the measured conversions were lower than the equilibrium predictions, indicating that the reactions were either...

Removal of heavy metals from kaolin using an upward electrokinetic soil remedial (UESR) technology

International Nuclear Information System (INIS)

Wang, J.-Y.; Huang, X.-J.; Kao, Jimmy C.M.; Stabnikova, Olena

2006-01-01

An upward electrokinetic soil remedial (UESR) technology was proposed to remove heavy metals from contaminated kaolin. Unlike conventional electrokinetic treatment that uses boreholes or trenches for horizontal migration of heavy metals, the UESR technology, applying vertical non-uniform electric fields, caused upward transportation of heavy metals to the top surface of the treated soil. The effects of current density, treatment duration, cell diameter, and different cathode chamber influent (distilled water or 0.01 M nitric acid) were studied. The removal efficiencies of heavy metals positively correlated to current density and treatment duration. Higher heavy metals removal efficiency was observed for the reactor cell with smaller diameter. A substantial amount of heavy metals was accumulated in the nearest to cathode 2 cm layer of kaolin when distilled water was continuously supplied to the cathode chamber. Heavy metals accumulated in this layer of kaolin can be easily excavated and disposed off. The main part of the removed heavy metals was dissolved in cathode chamber influent and moved away with cathode chamber effluent when 0.01 M nitric acid was used, instead of distilled water. Energy saving treatment by UESR technology with highest metal removal efficiencies was provided by two regimes: (1) by application of 0.01 M nitric acid as cathode chamber influent, cell diameter of 100 mm, duration of 18 days, and constant voltage of 3.5 V (19.7 kWh/m 3 of kaolin) and (2) by application of 0.01 M nitric acid as cathode chamber influent, cell diameter of 100 cm, duration of 6 days, and constant current density of 0.191 mA/cm 2 (19.1 kWh/m 3 of kaolin)

Sedimentation Characteristics of Kaolin and Bentonite in Concentrated Solutions

Directory of Open Access Journals (Sweden)

Abdulah Obut

2005-11-01

Full Text Available The sedimentation characteristics of two clays, namely kaolinite and bentonite, were determinated at high clay (5 % wt/vol and electrolyte (1 N concentrations using various inorganic-organic compounds. It was observed that the settling behaviour of kaolinite (1:1 clay and montmorillonite (2:1 clay is quite different due to the structural differences between these minerals. Although, similar initial settling rates and final sediment volumes were obtained after 24 hours of settling time for kaolin suspensions, the corresponding rates and volumes for bentonite suspensions varied greatly with the used chemical compound. According to the experimental results, a further intensive theoretical and experimental investigation is needed to reveal the mechanism underlying the sedimentation characteristics of clay minerals at high clay and electrolyte concentrations.

Electrochemical oxidation of pulp and paper making wastewater assisted by transition metal modified kaolin

International Nuclear Information System (INIS)

Wang Bo; Gu Lin; Ma Hongzhu

2007-01-01

The electrochemical oxidation of pulp and paper making wastewater assisted by transition metal (Co, Cu) modified kaolin in a 200 ml electrolytic batch reactor with graphite plate as electrodes was investigated. H 2 O 2 , which produced on the surface of porous graphite cathode, would react with the catalysts to form strong oxidant (hydroxyl radicals) that can in turn destruct the pollutants adsorbed on the surface of kaolin. The transition metal (Co, Cu) modified kaolin was also characterized by XRD and SEM before and after the modification and the results showed that the transition metals were completely supported on kaolin and formed a porous structure with big BET surface. The mechanism was proposed on the basis of XPS analysis of the catalyst after the degradation process. Series of experiments were also done to prove the synergetic effect of the combined oxidation system and to find out the optimal operating parameters such as initial pH, current density and amount of catalyst. From the results it can be founded that when the initial pH was at 3, current density was 30 mA cm -2 ; catalyst dose was 30 g dm -3 , COD (chemical oxygen demand) removal could reach up to 96.8% in 73 min

Recovery of kaolinite from tailings of Zonouz kaolin-washing plant by flotation-flocculation method

OpenAIRE

Kianoush Barani; Masoud Kalantari

2018-01-01

The traditional processing of kaolin is achieved by dispersion of the mined ore and classification by multistage hydrocyclone plants. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back into the quarry. In this research, recovery of kaolinite from tailings of Zonouz kaolin washing plant, which is located in Iran was investigated by flotation and flotation- flocculation. Flotation experiments show that the flotation of kaolinite from the tailings i...

Composite pigments based on surface coated kaolin and metakaolin

Czech Academy of Sciences Publication Activity Database

Štengl, Václav; Popelková, Daniela; Matys Grygar, Tomáš

2014-01-01

Roč. 101, NOV (2014), s. 149-158 ISSN 0169-1317 R&D Projects: GA MPO FR-TI1/006 Institutional support: RVO:61388980 Keywords : Kaolin * Homogeneous hydrolysis * Thioacetamide * Urea * Mullite * Metakaolin Subject RIV: CA - Inorganic Chemistry Impact factor: 2.467, year: 2014

Effects of Dietary Kaolin Supplementation on the Growth ...

African Journals Online (AJOL)

One hundred and sixty (160) Anak 2000 day-old broiler chicks were used to investigate the effects of kaolin on the haematology and growth performance of broilers. The chicks were randomly assigned to four treatments, each treatment consisting of four pens with 10 chicks per pen. The four treatments were; basal diet only ...

Electrical Properties of Zinc-Kaolin Composites below its Percolation ...

African Journals Online (AJOL)

Bheema

In this paper, we present some electrical properties of the zinc-kaolin cermet resistors ..... The temperature coefficient of resistance of a material is generally defined as .... Characterisation and morphological Studies of palladium modified carbon ... conduction and microstructural properties of semiconducting Co-doped TiO2.

Cure characteristics, crosslink density and degree of filler dispersion of kaolin-filled natural rubber compounds in the presence of alkanolamide

Science.gov (United States)

Surya, I.; Hayeemasae, N.; Ginting, M.

2018-03-01

The effects of alkanolamide (ALK) addition on cure characteristics, crosslink density and degree of filler dispersion of kaolin-filled natural rubber (NR) compounds were investigated. The kaolin filler was incorporated into NR compounds with a fixed loading, 30.0 phr. The ALK was prepared from Refined Bleached Deodorized Palm Stearin (RBDPS), a waste product of cooking oil production, and diethanolamine. The ALK is an oily material and added into the filled NR compounds as a rubber additive at different loadings, 0.0, 3.0, 5.0 and 7.0. The kaolin-filled NR compounds with and without ALK were vulcanized using a semi-efficient vulcanization system. It was found that ALK decreased the scorch and cure times and improved filler dispersion of the kaolin-filled NR compounds. The higher the ALK loading, the shorter were the scorch and cure times. It was also found that ALK increased the crosslink density of kaolin-filled NR compound up to 5.0 phr of loading. Due to its oily properties, The ALK acted as an internal plasticizer which decreased the minimum torque and improved the degree of kaolin dispersion in NR phases. The higher the ALK loading; the lower the minimum torque and better the filler dispersion.

DMC-grafted cellulose as green-based flocculants for agglomerating fine kaolin particles

Directory of Open Access Journals (Sweden)

Meng Li

2018-04-01

Full Text Available Novel cellulose based flocculants C-g-P (DMC with various chain architectures are synthesized through a situ graft copolymerization. The cationic ammonium chloride group (DMC is grafted onto cellulose by two separate inverse emulsion polymerization with γ-methacryloxypropyl trimethoxy silane (KH-570 and double bond addition reactions, which is a new and simple method to employ KH-570 as a bridge for the connection of cellulose matrix and DMC group. The effects of pH, flocculant dose, standing time on turbidity of kaolin suspensions and particle sizes have been studied systematically. In addition, the response surface methodology (RSM study confirms that PAC and C-g-P (DMC have synergy in turbidity removal with a higher removal efficiency of 98.32%. Moreover, C-g-P (DMC 1 has higher removal efficiency with 96.5% at a low dosage of 0.6 mg L−1 and better floc properties than C-g-P (DMC 2 and C-g-P (DMC 3, suggesting that the length and quantity of cationic branch chains play a crucial role in Kaolin flocculation due to their dramatically enhanced bridging effects. Keywords: Cellulose, Cationic flocculant, Inverse emulsion polymerization, Kaolin suspension

Effects of biochar on hydraulic conductivity of compacted kaolin clay.

Science.gov (United States)

Wong, James Tsz Fung; Chen, Zhongkui; Wong, Annie Yan Yan; Ng, Charles Wang Wai; Wong, Ming Hung

2018-03-01

Compacted clay is widely used as capillary barriers in landfill final cover system. Recently, biochar amended clay (BAC) has been proposed as a sustainable alternative cover material. However, the effects of biochar on saturated hydraulic conductivity (k sat ) of clay with high degree of compaction is not yet understood. The present study aims to investigate the effects of biochar on k sat of compacted kaolin clay. Soil specimens were prepared by amending kaolin clay with biochar derived from peanut-shell at 0, 5 and 20% (w/w). The k sat of soil specimens was measured using a flexible water permeameter. The effects of biochar on the microstructure of the compacted clay was also investigated using MIP. Adding 5% and 20% of biochar increased the k sat of compacted kaolin clay from 1.2 × 10 -9 to 2.1 × 10 -9 and 1.3 × 10 -8 ms -1 , respectively. The increase in k sat of clay was due to the shift in pore size distribution of compacted biochar-amended clay (BAC). MIP results revealed that adding 20% of biochar shifted the dominant pore diameter of clay from 0.01-0.1 μm (meso- and macropores) to 0.1-4 μm (macropores). Results reported in this communication revealed that biochar application increased the k sat of compacted clay, and the increment was positively correlated to the biochar percentage. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recovery of kaolinite from tailings of Zonouz kaolin-washing plant by flotation-flocculation method

Directory of Open Access Journals (Sweden)

Kianoush Barani

2018-04-01

Full Text Available The traditional processing of kaolin is achieved by dispersion of the mined ore and classification by multistage hydrocyclone plants. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back into the quarry. In this research, recovery of kaolinite from tailings of Zonouz kaolin washing plant, which is located in Iran was investigated by flotation and flotation- flocculation. Flotation experiments show that the flotation of kaolinite from the tailings is better in an acidic than in an alkaline medium containing cationic collectors. Flotation under acidic condition causes problems such as equipment corrosion at industrial scale. As a result, the cationic flotation of kaolinite is enhanced by addition of polyacrylamide as a flocculant. The results showed flocculation by polyacrylamide improved flotation of kaolinite within a range of pH. With 300 g/t dodecylamine, 500 g/t aluminum chloride, 50 g/t pine oil (frother, 15 g/t polyacrylamide, at pH = 7 and without de-slimming a product has 37.19% Al2O3, 54.19% SiO2 and 34.43% mass recovery was archived. Keywords: Kaolinite, Flotation, Flocculation, Cetylpyridinium chloride, Dodecylamine, Aluminum chloride, Polyacrylamide

Characterization of silica polymorphs in kaolins by X-ray diffraction before and after phosphoric acid digestion and thermal treatment

International Nuclear Information System (INIS)

Kahraman, Sibel; Oenal, Mueserref; Sarikaya, Yueksel; Bozdogan, Ihsan

2005-01-01

To characterize silica polymorphs (silicas) in some kaolins, orthophosphoric acid digestion (240 deg. C, 15 min), and thermal treatment (1050 deg. C, 24 h) were applied to eight samples. The original, digested, and heated samples were examined by X-ray diffraction (XRD). Crystalline silica quartz (SiO 2 ) was identified from the standard XRD patterns of the original kaolins; all contained quartz. On the other hand, hydrated partially crystalline silicas (SiO 2 .nH 2 O), such as well-ordered opal-C and opal-CT, were not readily distinguished from high-temperature crystalline silica, α-cristobalite, using standard XRD patterns of the original kaolins because, sharp and intense characteristic XRD peaks (h k l = 1 0 1) centered near 0.4 nm for opal-C, opal-CT, and α-cristobalite coincided. In order to distinguish these silicas the XRD patterns of the digested and heated samples were evaluated. It was observed that the 1 0 1 peaks disappear and sharpen in the course of digestion and heating, respectively. Because, the crystallinity of α-cristobalite does not change by these treatments, it was concluded that the kaolins contain opal-C and opal-CT or their mixtures in amorphous opal-A (SiO 2 .nH 2 O), but not α-cristobalite, which is probably human carcinogen. Because, the crystallinity increases in order opal-CT and opal-C, the narrowing in width at half-maximum peak height (FWHM) 1 0 1 must be more for opal-CT than opal-C by heating. Therefore, to distinguish opal-CT and opal-C from each other, the FWHM values before and after the heating process, were examined. Based on the results, it was estimated that six kaolins contain opal-CT in opal-A matrix, one kaolin contains only opal-A in a trace amount, and one kaolin contains non-opals

Flocculation of kaolin and lignin by bovine blood and hemoglobin

Science.gov (United States)

Polymeric flocculants are used extensively for water purification, inhibition of soil erosion, and reduction in water leakage from unlined canals. Production of highly active, renewable polymeric flocculants to replace synthetic flocculants is a priority. Using suspensions of kaolin, flocculation ...

Detection of tPA-Induced Hyperfibrinolysis in Whole Blood by RapidTEG, KaolinTEG, and Functional FibrinogenTEG in Healthy Individuals

DEFF Research Database (Denmark)

Genét, Gustav Folmer; Ostrowski, Sisse Rye; Sørensen, Anne Marie

2012-01-01

hyperfibrinolysis, as compared to standard KaolinTEG, is unknown. To investigate this, the ability of RapidTEG, KaolinTEG, and functional fibrinogenTEG (FFTEG) to detect tPA-induced (tissue plasminogen activator) lysis in whole blood from healthy individuals was investigated. Our hypothesis was that the initial...... powerful clot formation in the RapidTEG assay would reduce the sensitivity as compared to the normally used KaolinTEG assay. We also evaluated the FFTEG assay. Methods: In vitro comparison of the sensitivity of RapidTEG, KaolinTEG, and FFTEG to 1.8 nmol/L tPA in citrated whole blood (299 ± 23 ng/mL plasma......) induced hyperfibrinolysis in 10 healthy individuals and duplicate titration of the tPA whole blood (WB) concentration from 0.09 to 7.2 nmol/L (14-1144 ng/mL plasma) in 1 healthy donor. Results: At 1.8 nmol/L tPA, KaolinTEG, RapidTEG, and FFTEG all detected fibrinolysis but with different sensitivities...

synthesis of zeolite-a using kaolin samples from darazo, bauchi ...

African Journals Online (AJOL)

henry mgbemere

ekpeikenna@gmail.com, ... 13]. Kaolin is a naturally occurring mineral of the clay family and may contain a ..... Properties," World Journal of Nano Science and ... Treatment on Kankara Kaolinite," Opticon1826, vol. 15, pp. 1-5, 2013. .... 36(2) 444-451.

Influence of kaolin addition on the dynamics of oxygen mass transport in polyvinyl alcohol dispersion coatings

OpenAIRE

Nyflött, Åsa; Axrup, Lars; Gunilla, Carlsson; Järnström, Lars; Lestelius, Magnus; Moons, Ellen; Wahlström, Torbjörn

2015-01-01

The permeability of dispersion barriers produced from polyvinyl alcohol (PVOH) and kaolin clay blends coated onto polymeric supports has been studied by employing two different measurement methods: the oxygen transmission rate (OTR) and the ambient oxygen ingress rate (AOIR). Coatings with different thicknesses and kaolin contents were studied. Structural information of the dispersion-barrier coatings was obtained by Fourier transform infrared spectroscopy (FTIR) spectroscopy and scanning ele...

The mechanical and thermal characteristics of phenolic foam reinforced with kaolin powder and glass fiber fabric

Science.gov (United States)

Xiao, Wenya; Huang, Zhixiong; Ding, Jie

2017-12-01

In this work, kaolin powder and glass fiber fabric were added to PF in order to improve its thermal stability and mechanical property. Micro-structures of carbonized PF with kaolin powder were inspected by scanning electron microscopy (SEM) to demonstrate the filler’s pinning effect. SEM results illustrated modified PF had well morphology after high-temperature heat treatment. The Fourier transform infrared spectrometer (FTIR) test was carried out and found that kaolin powder only physically dispersed in PF. The compression test and thermal weight loss test were done on two groups of modified PF (Group A: add powder and fabric; Group B: add powder only). Results showed that all modified PF were better than pure PF, while foams with powder and fabric showed better mechanical characteristic and thermal stability compared with foams with powder only.

Alternatif Pembuatan Biodiesel Melalui Transesterifikasi Minyak Castor (Ricinus communis Menggunakan Katalis Campuran Cangkang Telur Ayam dan Kaolin

Directory of Open Access Journals (Sweden)

Soni - Setiadji

2017-05-01

Full Text Available Biodiesel was produced by transesterification of castor oil (Ricinus communis using a catalyst of CaO and kaolin (CaO / kaolin had been performed. CaO was obtained from the calcination of eggshell. Castor oil is selected as biodiesel feedstock because it belongs to non-food oil and easy to cultivate. In general, the research method aims to comprise the CaO / Kaolin catalysts with a ratio of 15 mmol CaO per 1 gram of kaolin activated using impregnation method and biodiesel produced through transesterification of castor oil using the catalyst at 65 ºC for 8 hours with ratio of castor oil: methanol: catalyst (1: 15: 5% w / w. The reaction is carried out on the reflux system. The XRD analysis show the presence of silica and potassium aluminum silicate hydroxide in the catalyst. The EDS results show the catalyst-forming components CaO and silica. The FTIR analysis results show the absorption peak in the functional group forming the methyl ester compound. Based on the characterization of GC-MS, the largest methyl ester components contained in biodiesel are methyl risinoleate, methyl elaidat, methyl stearate, methyl linoleate, and methyl palmitate. The overall conversion of castor oil to methyl ester using CaO / kaolin catalyst is 97.36%. The largest component in castor oil is risinoleic acid, has been successfully converted to methyl risinoleate by 74.75%.DOI: http://dx.doi.org/10.15408/jkv.v0i0.4778

Synthesis of Gamma-Alumina from Kankara Kaolin as Potential ...

African Journals Online (AJOL)

Engr Solomn Gajere

Large specific surface area gamma-alumina (γ-Al2O3) was synthesized by hydrothermal method using Kankara kaolin as starting material. Thermal treatment of ammonium alum prepared from the filtrate of the dealuminated metakaolin was employed to obtain the alumina. Crystalline aluminum sulfate with 39 wt% Al2O3 ...

Effects of Kaolin Application on Light Absorption and Distribution, Radiation Use Efficiency and Photosynthesis of Almond and Walnut Canopies

Science.gov (United States)

Rosati, Adolfo; Metcalf, Samuel G.; Buchner, Richard P.; Fulton, Allan E.; Lampinen, Bruce D.

2007-01-01

Background and Aims Kaolin applied as a suspension to plant canopies forms a film on leaves that increases reflection and reduces absorption of light. Photosynthesis of individual leaves is decreased while the photosynthesis of the whole canopy remains unaffected or even increases. This may result from a better distribution of light within the canopy following kaolin application, but this explanation has not been tested. The objective of this work was to study the effects of kaolin application on light distribution and absorption within tree canopies and, ultimately, on canopy photosynthesis and radiation use efficiency. Methods Photosynthetically active radiation (PAR) incident on individual leaves within the canopy of almond (Prunus dulcis) and walnut (Juglans regia) trees was measured before and after kaolin application in order to study PAR distribution within the canopy. The PAR incident on, and reflected and transmitted by, the canopy was measured on the same day for kaolin-sprayed and control trees in order to calculate canopy PAR absorption. These data were then used to model canopy photosynthesis and radiation use efficiency by a simple method proposed in previous work, based on the photosynthetic response to incident PAR of a top-canopy leaf. Key Results Kaolin increased incident PAR on surfaces of inner-canopy leaves, although there was an estimated 20 % loss in PAR reaching the photosynthetic apparatus, due to increased reflection. Assuming a 20 % loss of PAR, modelled photosynthesis and photosynthetic radiation use efficiency (PRUE) of kaolin-coated leaves decreased by only 6·3 %. This was due to (1) more beneficial PAR distribution within the kaolin-sprayed canopy, and (2) with decreasing PAR, leaf photosynthesis decreases less than proportionally, due to the curvature of the photosynthesis response-curve to PAR. The relatively small loss in canopy PRUE (per unit of incident PAR), coupled with the increased incident PAR on the leaf surface on

Characterization of ceramic masses using raw material of Para, Brazil: kaolin in natura

International Nuclear Information System (INIS)

Vida, T.A.; Facury Neto, E.; Rabelo, A.A.

2009-01-01

The incorporation rejects to the mixtures has if shown viable in the reduction of the environmental liability and for the obtaining of a better quality of the ceramic mass. In the present work, is tried to study the potentiality of the use of ceramic formulations with the addition of kaolin in natura to the clays. Formulations with two clays of the area of the municipal district of Maraba with addition of up to 60% in kaolin weight were prepared and characterized. For the determination of the physical and mechanical properties proof bodies were made by prensagem uniaxial and later burned in temperature from 900 to 1200 deg C with landing of 3 hours. The raw materials were characterized through diffraction of rays X (DRX) and thermogravimetric analysis. The proof bodies prepared were used for determination of the lineal retraction (RL), absorption of water, apparent porosity, apparent density, loss to the fire and rupture module the flexing. The results were satisfactory for the smallest kaolin tenors in the ceramic mass, and the mass with 20% presented rupture module elevated, in the temperature of 1200 deg C. (author)

Synthesis of Gamma-Alumina from Kankara Kaolin as Potential ...

African Journals Online (AJOL)

In compounded zeolite catalyst it serves as the active matrix which aids the conversion of the bulkiest molecules in the feed owing to its larger pore size than zeolite. Large specific surface area gamma-alumina (γ-Al2O3) was synthesized by hydrothermal method using Kankara kaolin as starting material. Thermal treatment ...

Design and development of a bio-inspired, under-actuated soft gripper.

Science.gov (United States)

Hassan, Taimoor; Manti, Mariangela; Passetti, Giovanni; d'Elia, Nicolò; Cianchetti, Matteo; Laschi, Cecilia

2015-08-01

The development of robotic devices able to perform manipulation tasks mimicking the human hand has been assessed on large scale. This work stands in the challenging scenario where soft materials are combined with bio-inspired design in order to develop soft grippers with improved grasping and holding capabilities. We are going to show a low-cost, under-actuated and adaptable soft gripper, highlighting the design and the manufacturing process. In particular, a critical analysis is made among three versions of the gripper with same design and actuation mechanism, but based on different materials. A novel actuation principle has been implemented in both cases, in order to reduce the encumbrance of the entire system and improve its aesthetics. Grasping and holding capabilities have been tested for each device, with target objects varying in shape, size and material. Results highlight synergy between the geometry and the intrinsic properties of the soft material, showing the way to novel design principles for soft grippers.

40 CFR 180.1180 - Kaolin; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

... Kaolin, when used on crops (apples, apricots, bananas, beans, cane berries, citrus fruits, corn, cotton... permit the marketing of the food commodities in this paragraph when treated in accordance with the...

Synthesis and characterization of kaolin assisted metal nanocomposite and its tremendous adsorptive and photo catalytic applications

International Nuclear Information System (INIS)

Tahir, H.; Saad, M.; Saleem, U.

2018-01-01

The present work demonstrates the synthesis of Kaolin assisted Ag nanocomposite (Ag-KNC) by co-precipitation method. The surface morphology of them was studied through SEM and chemical constituents by EDS techniques. The removal of efficaciousness of Ag-KNC was tested by Malachite Green Oxalate (MGO) dye through batch adsorption and photocatalytic strategies. The sorption experiments were preceded under the optimized conditions like amount of adsorbent, stay time and pH. The feasibility of the process was determined by employing Freundlich, Langmuir and D-R (Dubinin –Radushkevich) adsorption isotherms. The pH at point of zero charge (pHpzc) was conjointly calculable to work out the surface neutrality of the system. The salt effect for the removal of MGO dye was investigated. Thermodynamic parameters like free energy (∆Go), entropy (∆So) and enthalpy (∆Ho), of the system was investigated. Adsorption Kinetic was resolute by Intra particle diffusion (IPD) and Boyd’s models. An attempt was made to prepare (Ag-KCN) nanophoto catalyst by UV light assisted degradation of Malachite Green Oxalate (MGO) dye. They were prepared by the reduction of Ag+ ion under alkaline conditions on kaolin surface. The photo degradation (PD) process was initiated by photo generated electrons. The present study recommended that projected strategies were successfully applied for the remediation of environmental problems. (author)

Immobilization of horseradish peroxidase onto kaolin by glutaraldehyde method and its application in decolorization of anthraquinone dye

Directory of Open Access Journals (Sweden)

Šekuljica Nataša Ž.

2016-01-01

Full Text Available The problem of environmental pollution day by day becomes more worrisome, primarily due to the large amounts of wastewater contaminated with various harmful organic compounds, discharged into the environment untreated or partially clean. Feasibility of use of horseradish peroxidase (Amoracia rusticana in the synthetic dyes decolorization was approved by many researchers. Among a number of supports used for the immobilization, it was found that natural clay, kaolin has excellent features which are a precondition for obtaining biocatalysts with the excellent performances. For this reason, a horseradish peroxidase was immobilized onto kaolin using glutaraldehyde as a cross-linking agent. Obtained biocatalyst was applied in the decolorization of anthraquinone dye C. I. Acid Violet 109. Under determined optimal conditions (pH 4.0, hydrogen peroxide concentration 0.6 mM, dye concentration 30 mg L-1, temperature 24ºC around 76 % of dye decolorization was achieved. Reusability study showed that resulting biocatalyst was possible to apply four times in the desired reaction with relatively high decolorization percentage. [Projekat Ministarstva nauke Republike Srbije, br. III-46010 i br. 172013

Magnetic measurement of soft magnetic composites material under 3D SVPWM excitation

Science.gov (United States)

Zhang, Changgeng; Jiang, Baolin; Li, Yongjian; Yang, Qingxin

2018-05-01

The magnetic properties measurement and analysis of soft magnetic material under the rotational space-vector pulse width modulation (SVPWM) excitation are key factors in design and optimization of the adjustable speed motor. In this paper, a three-dimensional (3D) magnetic properties testing system fit for SVPWM excitation is built, which includes symmetrical orthogonal excitation magnetic circuit and cubic field-metric sensor. Base on the testing system, the vector B and H loci of soft magnetic composite (SMC) material under SVPWM excitation are measured and analyzed by proposed 3D SVPWM control method. Alternating and rotating core losses under various complex excitation with different magnitude modulation ratio are calculated and compared.

Caulins brasileiros: alguns aspectos da geologia e da mineralogia Brazilian kaolins: some aspects of the geology and mineralogy

Directory of Open Access Journals (Sweden)

Ian Richard Wilson

1998-08-01

Full Text Available A dimensão do Brasil e a diversidade da geologia se reflete em vários meios nos quais montagens de caulinita foram formadas. Os meios geológicos dos caulins brasileiros podem ser divididos nos seguintes grupos - caulins sedimentares, caulins oriundos de pegmatitas, de rochas graníticas, de rochas vulcânicas, e caulins derivados de anortosito. As argilas sedimentares são encontradas principalmente na bacia amazônica e aquelas adjacentes ao rio Jari estão sendo exploradas comercialmente para exportação como argilas para recobrimento de papel. Os caulins amazônicos são caracterizados por alto teor de ferro e titânia (estruturais com baixos níveis de álcalis e exibindo cristais de caulinita euédricos. As pegmatitas do sudeste, quando não recobertas com óxido de ferro, tem extremamente baixos teores de ferro e titânia e uma mistura de caulinita 7Å / haloisita 10Å ocorre em todos depósitos. As pegmatitas do nordeste produzem caulins constituídos somente por caulinitas euédricas com ausência de haloisita. Os caulins de granito tem geralmente maiores teores de ferro quando comparados com pegmatitas e são raros os depósitos constituídos somente por caulinita, sendo comum uma mistura de caulinita 7Å / haloisita. Os caulins obtidos da pegmatita e do granito são utilizados como cobertura de papel e em cerâmica em geral. Argilas de origem vulcânica são utilizadas em cerâmicas na região. Os caulins obtidos de anortosito são semelhantes em níveis de ferro e titânia àqueles obtidos de caulins graníticos. Montagens de caulinita e pequenas quantidades de haloisita 7Å são encontrados. Essas argilas são usadas tanto em cerâmicas de mesa quanto em preenchimentos para papel.The size of Brazil and the diversity of geology is reflected in varying environments in which kaolinite assemblages have been formed. The geological environments of the Brazilian kaolin may be divided into the following groups - sedimentary kaolin

A Mexican kaolin deposit: XANES characterization, mineralogical phase analysis and applications

Directory of Open Access Journals (Sweden)

Martínez, A.

2009-06-01

Full Text Available A kaolin obtained from Villa de Reyes, a region near to San Luis Potosí (México was characterized by means of X-ray powder diffraction (XRD, optical microscopy (OM, scanning electron microscopy (SEM, X-ray fluorescence (XRF, X-Ray Absorption Near Edge Spectroscopy (XANES, thermal analysis (DTA/TGA, dilatometry (DIL, and chemical analysis. Mineralogical and morphological characteristics of the mineral are presented. The kaolin sample was formed mainly by kaolinite, but other minor phases were also detected such as quartz, cristobalite, tridymite, and dolomite. The high content of volcanic glass detected, by optical microscopy, revealed an incomplete kaolinization process of the raw material. The reddish color of the kaolin was associated with the free iron content in the form of limonite [FeO(OH], which was determined by XANES. The influence of the particle size on the whiteness of kaolin was evaluated. Dilatometric analysis revealed a strong thermal expansion between 110 y 240 °C, which would difficult the use of this material in traditional ceramic applications. On the other hand the presence of glass and high temperature phases of SiO2, such as cristobalite and tridymite will favor its use in the cement industry.El caolín obtenido de Villa de Reyes, una región cercana a San Luis Potosí, México, fue caracterizado por las siguientes técnicas: difracción de rayos-X en polvos (DRX, microscopía óptica (MO, microscopía electrónica de barrido (MEB, fluorescencia de rayos-X (FRX, espectroscopía de absorción de rayos-X (XANES, análisis térmico (DTA/TGA, dilatometría (DIL y análisis químico. Los resultados del análisis mineralógico mediante DRX mostraron un mineral constituido principalmente de caolinita, con una contribución minoritaria de cuarzo, cristobalita, tridimita y dolomita. El análisis por microscopía óptica reveló un alto contenido de material amorfo volcánico, indicando una caolinización incompleta del material v

Synthesis of type A zeolite from calcinated kaolin

International Nuclear Information System (INIS)

Rodrigues, E.C.; Neves, R.F.; Souza, J.A.S.; Moraes, C.G.; Macedo, E.N.

2011-01-01

The mineral production has caused great concern in environmental and industrial scenario due to the effects caused to the environment. The industries of processing kaolin for paper are important economically for the state of Para, but produce huge quantities of tailings, which depend on large areas to be stocked. This material is rich in silico-aluminates can be recycled and used as raw material for other industries. The objective is to synthesize zeolite A at different temperatures of calcination and synthesis. The starting materials and synthesis of zeolite A have been identified and characterized through analysis of X-ray diffraction (DRX) and scanning electron microscopy (MEV). The synthesis process of zeolite A, using as source of silica and the aluminum metakaolin, which was calcined at temperatures of 700 ° C and 800 ° C for 2 hours of landing in a burning furnace type muffle. Observed in relation to the calcination of kaolin as the main phase, the metakaolin. This is just a removal of water from its structure, so we opted for the lower temperature, less energy consumption. The synthesis process of zeolite A, produced good results for the formation of zeolites type A, which were characterized with high purities. (author)

Facile Fabrication of a Hierarchical Superhydrophobic Coating with Aluminate Coupling Agent Modified Kaolin

Directory of Open Access Journals (Sweden)

Hui Li

2013-01-01

Full Text Available A superhydrophobic coating was fabricated from the dispersion of unmodified kaolin particles and aluminate coupling agent in anhydrous ethanol. Through surface modification, water contact angle of the coating prepared by modified kaolin particles increased dramatically from 0° to 152°, and the sliding angle decreased from 90° to 3°. Scanning electron microscopy was used to examine the surface morphology. A structure composed of micro-nano hierarchical component, combined with the surface modification by aluminate coupling agent which reduced the surface energy greatly, was found to be responsible for the superhydrophobicity. The method adopted is relatively simple, facile, and cost-effective and can potentially be applied to large water-repellent surface coatings.

Tools to support maintenance strategies under soft soil conditions

Directory of Open Access Journals (Sweden)

J. W. M. Lambert

2015-11-01

Full Text Available Costs for maintenance of infrastructure in municipalities with soft soil underground conditions, are estimated to be almost 40 % higher than in others. As a result, these municipalities meet financial problems that cause overdue maintenance. In some cases municipalities are even afraid to be unable to offer a minimum service level in future. In common, traditional practice, roads and sewerage systems have been constructed in trenches that consist of sandy material that replaces the upper meters of the soft soil. Under influence of its weight, this causes accelerated settlements of the construction. A number of alternative constructions have been developed, e.g. using light-weight materials to limit settlement velocity. In order to limit future maintenance costs, improvement of maintenance strategies is desired. Tools have been and will be developed to support municipalities in improving their maintenance strategies and save money by doing that. A model (BALANS that weighs the attractiveness of alternative solutions under different soil, environmental and economic circumstances, will be presented.

Study of the effect of Kaolin in the mortar of cement matrices by confinement of ion exchange resins

Directory of Open Access Journals (Sweden)

Labied S.

2018-01-01

Full Text Available Radioactive waste arising as a result of nuclear activities should be safely managed from its generation to final disposal in an appropriate conditioned form to reduce the risk of radiation exposure of technical personnel and of the public and to limit contamination of the environment. The immobilization of low and intermediate level radioactive wastes in cementitious matrices is the most commonly used technique to produce inexpensive waste matrix that complies with regulatory requirements in order to protect humans and the environment against nuisance caused by ionizing radiation. Cement based materials are used in radioactive waste management to produce stable waste forms. This matrix constitutes the first build engineering barrier in disposal facilities. In this work, the kaolin is used to enhance the mechanical performance of the matrix of confinement of ion exchange resins by gradually replacing the sand in mortar with kaolin clay. The Kaolin clay sample was a special pure product, sourced from a foreign country. The maximum quantity of resins that can be incorporated into the mortar formulation without the packages losing their strength is 13.915% which results in a better mechanical strength at 6.7686 MPA compression with kaolin.

Application of kaolin-based catalysts in biodiesel production via transesterification of vegetable oils in excess methanol.

Science.gov (United States)

Dang, Tan Hiep; Chen, Bing-Hung; Lee, Duu-Jong

2013-10-01

Biodiesel production from transesterification of vegetable oils in excess methanol was performed by using as-prepared catalyst from low-cost kaolin clay. This effective heterogeneous catalyst was successfully prepared from natural kaolin firstly by dehydroxylation at 800°C for 10h and, subsequently, by NaOH-activation hydrothermally at 90°C for 24h and calcined again at 500°C for 6h. The as-obtained catalytic material was characterized with instruments, including FT-IR, XRD, SEM, and porosimeter (BET/BJH analysis). The as-prepared catalyst was advantageous not only for its easy preparation, but also for its cost-efficiency and superior catalysis in transesterification of vegetable oils in excess methanol to produce fatty acid methyl esters (FAMEs). Conversion efficiencies of soybean and palm oils to biodiesel over the as-prepared catalysts reached 97.0±3.0% and 95.4±3.7%, respectively, under optimal conditions. Activation energies of transesterification reactions of soybean and palm oils in excess methanol using these catalysts are 14.09 kJ/mol and 48.87 kJ/mol, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of Melatonin on the Cerebellum of Infant Rat Following Kaolin-Induced Hydrocephalus: a Histochemical and Immunohistochemical Study.

Science.gov (United States)

Uyanıkgil, Yiğit; Turgut, Mehmet; Baka, Meral

2017-02-01

Hydrocephalus is a developmental disorder causing abnormally collected cerebrospinal fluid within the cerebral ventricles. It leads to bigger skulls and many dysfunctions related to the nervous system. Here, we addressed whether exogenous melatonin administration could reverse the clinical features of kaolin-induced hydrocephalus in infantile rats. A controlled double-blinded study was conducted in 2-week-old 45 Wistar albino rats, which were divided into three groups: Group A, the control group, received intracisternal sham injection with solely the needle insertion; group B, the hydrocephalus group, was treated with isotonic NaCl after kaolin injection; and group C, the hydrocephalus + melatonin group, was given i.p. exogenous melatonin at a dose of 0.5 mg/100 g body weight after kaolin injection. Histological and immunohistochemical analyses were performed after the induction of hydrocephalus and melatonin administration. Glial fibrillary acidic protein was stained by immunohistochemical method. TUNEL method was used to define and quantitate apoptosis in the cerebellar tissues. Statistical analysis was performed by nonparametric Kruskal-Wallis H test, and once significance was determined among means, post hoc pairwise comparisons were carried out using Mann-Whitney U test. We found that melatonin administration significantly ameliorated ratio of substantia grisea area/substantia alba area in the cerebellum of infantile rats. Histologically, there was a significant reduction in the number of cerebellar apoptotic cells after the hydrocephalus induced by kaolin (P cerebellum were reversed by systemic melatonin administration in infantile rats with kaolin-induced hydrocephalus. Nevertheless, further studies are needed to suggest melatonin as a candidate protective drug in children with hydrocephalus.

Particle morphology and mineral structure of heavy metal-contaminated kaolin soil before and after electrokinetic remediation.

Science.gov (United States)

Roach, Nicole; Reddy, Krishna R; Al-Hamdan, Ashraf Z

2009-06-15

This study aims to characterize the physical distribution of heavy metals in kaolin soil and the chemical and structural changes in kaolinite minerals that result from electrokinetic remediation. Three bench-scale electrokinetic experiments were conducted on kaolin that was spiked with Cr(VI) alone, Ni (II) alone, and a combination of Cr(VI), Ni(II) and Cd(II) under a constant electric potential of 1VDC/cm for a total duration of 4 days. Transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD) analyses were performed on the soil samples before and after electrokinetic remediation. Results showed that the heavy metal contaminant distribution in the soil samples was not observable using TEM and EDX. EDX detected nickel and chromium on some kaolinite particles and titanium-rich, high-contrast particles, but no separate phases containing the metal contaminants were detected. Small amounts of heavy metal contaminants that were detected by EDX in the absence of a visible phase suggest that ions are adsorbed to kaolinite particle surfaces as a thin coating. There was also no clear correlation between semiquantitative analysis of EDX spectra and measured total metal concentrations, which may be attributed to low heavy metal concentrations and small size of samples used. X-ray diffraction analyses were aimed to detect any structural changes in kaolinite minerals resulting from EK. The diffraction patterns showed a decrease in peak height with decreasing soil pH value, which indicates possible dissolution of kaolinite minerals during electrokinetic remediation. Overall this study showed that the changes in particle morphology were found to be insignificant, but a relationship was found between the crystallinity of kaolin and the pH changes induced by the applied electric potential.

Particle morphology and mineral structure of heavy metal-contaminated kaolin soil before and after electrokinetic remediation

International Nuclear Information System (INIS)

Roach, Nicole; Reddy, Krishna R.; Al-Hamdan, Ashraf Z.

2009-01-01

This study aims to characterize the physical distribution of heavy metals in kaolin soil and the chemical and structural changes in kaolinite minerals that result from electrokinetic remediation. Three bench-scale electrokinetic experiments were conducted on kaolin that was spiked with Cr(VI) alone, Ni (II) alone, and a combination of Cr(VI), Ni(II) and Cd(II) under a constant electric potential of 1 VDC/cm for a total duration of 4 days. Transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD) analyses were performed on the soil samples before and after electrokinetic remediation. Results showed that the heavy metal contaminant distribution in the soil samples was not observable using TEM and EDX. EDX detected nickel and chromium on some kaolinite particles and titanium-rich, high-contrast particles, but no separate phases containing the metal contaminants were detected. Small amounts of heavy metal contaminants that were detected by EDX in the absence of a visible phase suggest that ions are adsorbed to kaolinite particle surfaces as a thin coating. There was also no clear correlation between semiquantitative analysis of EDX spectra and measured total metal concentrations, which may be attributed to low heavy metal concentrations and small size of samples used. X-ray diffraction analyses were aimed to detect any structural changes in kaolinite minerals resulting from EK. The diffraction patterns showed a decrease in peak height with decreasing soil pH value, which indicates possible dissolution of kaolinite minerals during electrokinetic remediation. Overall this study showed that the changes in particle morphology were found to be insignificant, but a relationship was found between the crystallinity of kaolin and the pH changes induced by the applied electric potential.

A study on spalling in soft rock under low confining stress

International Nuclear Information System (INIS)

Tomita, Atsunori; Ebina, Takahito; Toida, Masaru; Shirasagi, Suguru; Kishida, Kiyoshi; Adachi, Toshihisa

2007-01-01

The aim of this paper is to study spalling in soft rock excavation. During the test cavern excavation of the radioactive waste disposal project, spalling occurred. Therefore, it has been estimated performing the stress path simulation test and measuring the induced stress. In the stress path simulation test, the splitting failure has been confirmed under low confining stress. In the induced stress measurements, the rock mass around the cavern has shifted to the low radial confinement. Hence, spalling in soft rock was interpreted by the splitting failure caused by the induced stress under low confinement. Furthermore, the failure zone was proved by the numerical analysis applying the criterion based on the results of the above triaxial test. (author)

Long-Chain Diacrylate Crosslinkers and Use of PEG Crosslinks in Poly(potassium acrylate-acrylic acid)/Kaolin Composite Superabsorbents

OpenAIRE

Koroush Kabiri; Siavash Nafisi; Mohammad jalaledin Zohuriaan-Mehr; Ali Akbar Yousefi

2013-01-01

Long-chain diacrylate crosslinkers based on linear α,ω-diols were synthesized and characterized using FTIR and 1H NMR spectroscopy. The highest reaction yield (99.5%) was due to polyethylene glycol diacrylate 1000 (PEGDA-1000). Then, kaolin-containing poly(potassium acrylate-acrylic acid) superabsorbent composites and kaolin-free counterparts were synthesized using PEGDA-1000.The effect of the crosslinker concentration on swelling, rheological and thermo-mechanical properties was investigated...

Synthesis of kaolin supported nanoscale zero-valent iron and its degradation mechanism of Direct Fast Black G in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Jin, Xiaoying; Chen, Zhengxian [Fujian Key Laboratory of Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Zhou, Rongbing [Institute of Environ Sci and Engineering, Hangzhou Dianzi University, Hangzhou, Zhejiang 310018 (China); Chen, Zuliang, E-mail: Zuliang.chen@unisa.edu.au [Fujian Key Laboratory of Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes, SA 5095 (Australia)

2015-01-15

Graphical abstract: UV–visible spectra of DFBG solution using K-nZVI (1:1) nanoparticles. (a) Before reaction; (b) during reaction; (c) after reaction. - Highlights: • Kaolin-supported Fe{sup 0} nanoparticle (K-nZVI) was synthesized. • Degradation of Direct Fast Black by K-nZVI was studied. • K-nZVI was characterized by SEM, XRD, UV and FIIR. • Degradation mechanism of Direct Fast Black was proposed. - Abstract: Calcinated kaolin supported nanoscale zero-valent iron (K-nZVI) was synthesized and used for the removal of tetrad azo-group dye-Direct Fast Black G (DFBG) from aqueous solution. The results demonstrated that after reacting for 10 min with an initial concentration of DFBG 100 mg L{sup −1} (pH 9.49), 78.60% of DFBG was removed using K-nZVI, while only 41.39% and 12.56% of DFBG were removed using nZVI and kaolin, respectively. K-nZVI with a mass ratio of nZVI nanoparticles versus kaolin at 1:1 was found to have a high degree of reactivity. Furthermore, scanning electron microscopy (SEM) confirmed that nZVI was better dispersed when kaolin was present. XRD patterns indicated that iron oxides were formed after reaction. Fourier transforms infrared spectra (FTIR) and UV–visible demonstrated that the peak in the visible light region of DFBG was degraded and new bands were observed. Kinetics studies showed that the degradation of DFBG fitted well to the pseudo first-order model. The degradation of DFBG by K-nZVI was based on its adsorption onto kaolin and iron oxides, and subsequently reduction using nZVI was proposed. A significant outcome emerged in that 99.84% of DFBG in wastewater was removed using K-nZVI after reacting for 60 min.

Synthesis of kaolin supported nanoscale zero-valent iron and its degradation mechanism of Direct Fast Black G in aqueous solution

International Nuclear Information System (INIS)

Jin, Xiaoying; Chen, Zhengxian; Zhou, Rongbing; Chen, Zuliang

2015-01-01

Graphical abstract: UV–visible spectra of DFBG solution using K-nZVI (1:1) nanoparticles. (a) Before reaction; (b) during reaction; (c) after reaction. - Highlights: • Kaolin-supported Fe 0 nanoparticle (K-nZVI) was synthesized. • Degradation of Direct Fast Black by K-nZVI was studied. • K-nZVI was characterized by SEM, XRD, UV and FIIR. • Degradation mechanism of Direct Fast Black was proposed. - Abstract: Calcinated kaolin supported nanoscale zero-valent iron (K-nZVI) was synthesized and used for the removal of tetrad azo-group dye-Direct Fast Black G (DFBG) from aqueous solution. The results demonstrated that after reacting for 10 min with an initial concentration of DFBG 100 mg L −1 (pH 9.49), 78.60% of DFBG was removed using K-nZVI, while only 41.39% and 12.56% of DFBG were removed using nZVI and kaolin, respectively. K-nZVI with a mass ratio of nZVI nanoparticles versus kaolin at 1:1 was found to have a high degree of reactivity. Furthermore, scanning electron microscopy (SEM) confirmed that nZVI was better dispersed when kaolin was present. XRD patterns indicated that iron oxides were formed after reaction. Fourier transforms infrared spectra (FTIR) and UV–visible demonstrated that the peak in the visible light region of DFBG was degraded and new bands were observed. Kinetics studies showed that the degradation of DFBG fitted well to the pseudo first-order model. The degradation of DFBG by K-nZVI was based on its adsorption onto kaolin and iron oxides, and subsequently reduction using nZVI was proposed. A significant outcome emerged in that 99.84% of DFBG in wastewater was removed using K-nZVI after reacting for 60 min

Physico-Chemical Properties of Kaolin-Organic Acid

Directory of Open Access Journals (Sweden)

Yeo S.W.

2017-01-01

Full Text Available Soil with more than 20% of organic content is classified as organic soil in Malaysia. Contents of organic soil consist of different types of organic and inorganic matter. Each type of organic matter has its own characteristic and its effect on the properties of the soil is different. Hence, a good understanding on the effect of specific organic and inorganic matter on the physico-chemical characteristic of organic soils can serve as a guide for predicting the properties of organic soils. The main objective is to unveil the effect of organic acid on the physico-chemical properties of soil. Artificial organic soil (kaolin mixed with organic acid was utilized in order to minimize the geochemical variability of studied soil. The organic acid which consists of humic acid and fulvic acid was extracted from highly humificated plant–based compost. The effect of organic acid on the physico-chemical properties of soil was determined by varying the concentration of organic acid. The specific gravity, Atterberg limits, pH, bulk chemical composition and the functional group of kaolin-organic acid were determined. It was found that the plasticity index, specific gravity and pH value were decreased with lowered concentration of organic acid. However, the liquid limits and plastic limits were found to be increased with the concentration decrement of organic acid. The analysis of XRF on the bulk chemical composition and analysis of FTIR spectra on the functional group of artificial organic soils with different concentration have confirmed little geochemical variability between samples.

Characterization of kaolin dispersion using acoustic and electroacoustic spectroscopy

OpenAIRE

Dohnalová Ž.; Svoboda L.; Šulcová P.

2008-01-01

The objective of this work is the investigation of the kaolin dispersion by the ultrasonic techniques. In contact with aqueous solution clay minerals show cation - exchange properties and certain degree of dissolution or rather selective leaching of components. The work is divided into two main parts - determination of zeta potential and particle size distribution. The first part is focused on measuring of zeta potential. Effects of concentration of solid, different kind of electrolytes (0.01...

Feasible synthesis of TiO2 deposited on kaolin for photocatalytic applications

Czech Academy of Sciences Publication Activity Database

Henych, Jiří; Štengl, Václav

2013-01-01

Roč. 61, 3-4 (2013), s. 165-176 ISSN 0009-8604 R&D Projects: GA MPO FR-TI1/006 Institutional support: RVO:61388980 Keywords : Homogeneous Hydrolysis * Kaolin * Photocatalysis * TiO2 * Urea Subject RIV: CA - Inorganic Chemistry Impact factor: 1.398, year: 2013

Elaboration and characterization of mullite-anorthite-albite porous ceramics prepared from Algerian kaolin

International Nuclear Information System (INIS)

Rouabhia, F.; Nemamcha, A.; Moumeni, H.

2018-01-01

Mullite-anorthite-albite porous ceramic materials were successfully prepared by a solid-state reaction between kaolin clay and two different additives (CaCO 3 and Na 2 CO 3 ). The starting raw material was characterized by X-ray fluorescence, X-ray diffraction (XRD) and dynamic light scattering techniques. The effect of CaCO 3 and Na 2 CO 3 concentration (10 to 70 wt%) on structure, morphology and thermal properties of the obtained ceramics was investigated by XRD, scanning electron microscopy and differential scanning calorimetry (DSC) techniques. The XRD patterns showed that mullite (3Al 2 O 3 .2SiO 2 ), anorthite (CaO.Al 2 O 3 .2SiO 2 ) and albite (Na 2 O.Al 2 O 3 .6SiO 2 ) were the main crystalline phases present in the materials. The morphology investigation revealed the porous texture of obtained ceramics characterized by the presence of sponge-like structure mainly due to the additive decomposition at high temperatures. The DSC results confirm the presence of four temperature regions related to the kaolin thermal transformations and the formation of minerals. The temperature and enthalpy of mineral formation are additive concentration dependent. As a result, the optimal content of additives which allowed the coexistence of the three phases, a spongelike morphology, and high porosity without cracks corresponded to 15 wt% CaCO 3 , 15 wt% Na 2 CO 3 , and 70 wt% kaolin. (author)

Synthesis of microporous material faujasite-type from kaolin waste; Sintese de material microporoso do tipo faujasita a partir de rejeito de caulim

Energy Technology Data Exchange (ETDEWEB)

Hildebrando, E.A.; Valenzuela-Diaz, F.R., E-mail: edemarino@usp.b [Universidade de Sao Paulo (USP), SP (Brazil). Dept. de Engenharia Metalurgica e de Materiais. Lab. de Materias-Primas Particuladas e Solidos nao Metalicos; Angelica, R.S. [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Geociencias. Fac. de Geologia; Neves, R.F. [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Tecnologia. Fac. de Engenharia Quimica

2010-07-01

Zeolite with structure faujasite was synthesized using kaolin waste from kaolin processing industries for paper coating as predominant source of silicon and aluminum; the starting material was characterized by XRF, XRD, DTA/TG, SEM, and products obtained by XRD and SEM. Synthesis in hydrothermal conditions occurred on autoclave and time-temperature effects, as well as the relationship Si/Al were considered. The results show that the methodology developed with the waste of calcined kaolin reacting at 90 deg C for 20 hours in an alkaline medium, in the presence of an additional source of silica was obtained zeolite Y as single phase present in the product. (author)

Fire performance of fiber board coated with nano kaolin-clay film

Science.gov (United States)

Zhijia Liu; John F. Hunt; Zhiyong Cai

2013-01-01

Fiberboard is a common interior material used both in China and the United States of America. The increase in demand for interior materials has raised concerns regarding combustibility of the materials. The pyrolysis characteristics of fiber, phenolic resin (PF), and nano kaolin-clay (NK) were investigated using thermogravimetry. The fire performances of samples coated...

Investigation on the effect of sintering temperature on kaolin hollow fibre membrane for dye filtration.

Science.gov (United States)

Mohtor, Nur Hamizah; Othman, Mohd Hafiz Dzarfan; Ismail, Ahmad Fauzi; Rahman, Mukhlis A; Jaafar, Juhana; Hashim, Nur Awanis

2017-07-01

Despite its extraordinary price, ceramic membrane can still be able to surpass polymeric membrane in the applications that require high temperature and pressure conditions, as well as harsh chemical environment. In order to alleviate the high cost of ceramic material that still becomes one of the major factors that contributes to the high production cost of ceramic membrane, various attempts have been made to use low cost ceramic materials as alternatives to well-known expensive ceramic materials such as alumina, silica, and zirconia in the fabrication of ceramic membrane. Thus, local Malaysian kaolin has been chosen as the ceramic material in this study for the preparation of kaolin hollow fibre membrane since it is inexpensive and naturally abundant in Malaysia. Due to the fact that the sintering process plays a prominent role in obtaining the desired morphology, properties, and performances of prepared ceramic membrane, the aim of this work was to study the effect of different sintering temperatures applied (ranging from 1200 to 1500 °C) in the preparation of kaolin hollow fibre membrane via dry/wet phase inversion-based spinning technique and sintering process. The morphology and properties of membrane were then characterised by SEM, AFM, FTIR, XRD, and three-point bending test, while the performances of membrane were investigated by conducting water permeation and Reactive Black 5 (RB5) dye rejection tests. From the experimental results obtained, the sintering temperature of 1400 °C could be selected as the optimum sintering temperature in preparing the kaolin hollow fibre membrane with the dense sponge-like structure of separation layer that resulted in the good mechanical strength of 70 MPa with the appreciable water permeation of 75 L/h m 2  bar and RB5 rejection of 68%.

Thermodynamic analysis of stability in iron removal from kaolin by using oxalic acid

Directory of Open Access Journals (Sweden)

C. Ocampo-López

2013-06-01

Full Text Available The graphical representation of global stability for a system, or Pourbaix diagram, was constructed to perform a thermodynamic study of iron removal from kaolin using oxalic acid as an oxidant. To do this the free energies of formation of the oxalate complex of the system were calculated, and it was found that the more stable specie is Fe(C2O43-3, with a calculated free energy of formation of -3753.88 kcal/mol. Thermodynamic stability functions were estimated for the system as a function of pH and Eh known as potential of oxide reduction. It was built a global stability diagram for the removal system; it showed that the specie trioxalate Fe(C2O43-3 is the only oxalate in equilibrium with other compounds associated with the removal of iron in kaolin.

Synthesis and characterization of mangan oxide coated sand from Capkala kaolin

Science.gov (United States)

Destiarti, Lia; Wahyuni, Nelly; Prawatya, Yopa Eka; Sasri, Risya

2017-03-01

Synthesis and characterization of mangan oxide coated sand from quartz sand fraction of Capkala kaolin has been conducted. There were two methods on synthesis of Mangan Oxide Coated Sand (MOCS) from Capkala Kaolin compared in this research. Characterization of MOCS was done by using Scanning Electron Microscope/Energy Dispersive X-Ray Spectrometer (SEM/EDX) and X-Ray Diffraction (XRD). The MOCS was tested to reduce phosphate in laundry waste. The result showed that the natural sand had bigger agregates and a relatively uniform structural orientation while both MOCS had heterogen structural orientation and manganese oxide formed in cluster. Manganese in first and second methods were 1,93% and 2,63%, respectively. The XRD spectrum showed clear reflections at 22,80°, 36,04°, 37,60° and a broad band at 26,62° (SiO2). Based on XRD spectrum, it can be concluded that mineral constituents of MOCS was verified corresponding to pyrolusite (MnO2). The former MOCS could reduce almost 60% while the later could reduce 70% phosphate in laundry waste.

Characterization of kaolin and granite waste for formulation of porcelain stoneware tiles

International Nuclear Information System (INIS)

Luna da Silveira, G.C.; Acchar, W.; Gomes, U.U.; Silva, B.K.O.; Luna da Silveira, R.V.; Labrincha, J.A.; Costa, M.C.P.

2016-01-01

To produce a stoneware tiles is necessary develop a formulation that satisfies their structural characteristics, micro-structural, physical and mechanical properties. Thus, in order to create a formulation for porcelain stoneware tiles that give use to kaolin and granite waste used in the production of ceramic materials were asked the following characterizations: chemical analysis, mineralogical, thermal and particle size. We found that in the kaolin sample it presents a rate of silicon oxide and aluminum oxide similar to those found in the work of other investigators, about 45.23% SiO2 and 37.39% Al_2O_3. In the granite waste, the percentage of silicon oxide and aluminum oxide are also similar to those observed in other studies, with about 74.89% SiO2 and 10.54% Al_2O_3. Both the percentage of SiO_2 and Al_2O_3 founded in these two samples satisfy the percentage required in the manufacturing of porcelain stoneware tiles. (author)

New organophilic kaolin clays based on single-point grafted 3-aminopropyl dimethylethoxysilane.

Science.gov (United States)

Zaharia, A; Perrin, F-X; Teodorescu, M; Radu, A-L; Iordache, T-V; Florea, A-M; Donescu, D; Sarbu, A

2015-10-14

In this study, the organophilization procedure of kaolin rocks with a monofunctional ethoxysilane- 3 aminopropyl dimethyl ethoxysilane (APMS) is depicted for the first time. The two-step organophilization procedure, including dimethyl sulfoxide intercalation and APMS grafting onto the inner hydroxyl surface of kaolinite (the mineral) layers was tested for three sources of kaolin rocks (KR, KC and KD) with various morphologies and kaolinite compositions. The load of APMS in the kaolinite interlayer space was higher than that of 3-aminopropyl triethoxysilane (APTS) due to the single-point grafting nature of the organophilization reaction. A higher long-distance order of kaolinite layers with low staking was obtained for the APMS, due to a more controllable organiphilization reaction. Last but not least, the solid state (29)Si-NMR tests confirmed the single-point grafting mechanism of APMS, corroborating monodentate fixation on the kaolinite hydroxyl facets, with no contribution to the bidentate or tridentate fixation as observed for APTS.

Control of the Mexican bean weevil Zabrotes subfasciatus with kaolin Controle do caruncho-do-feijão Zabrotes subfasciatus com caulim

Directory of Open Access Journals (Sweden)

Adriana Yatie Mikami

2010-07-01

Full Text Available The Mexican bean weevil Zabrotes subfasciatus (Coleoptera: Chrysomelidae: Bruchinae is an important pest of stored beans in tropical regions. The efficiency of kaolin [with or without neem (Azadirachta indica oil] and diatomaceous earth (DE (standard treatment was studied in laboratory aiming to obtain alternatives for chemical control of this insect. Insects were confined in plastic vials containing beans treated with kaolin (2, 4 and 8g kg-1, kaolin + neem [2g kg-1(5% neem oil], diatomaceous earth (1g kg-1 and control. Mortality of adult insects, number of eggs and F1generation beetles emergency were assessed. Kaolin caused mortality of Z. subfasciatus, however higher periods and doses than DE were necessary to promote high mortality (100% or close. Kaolin treatments also affected female behavior because many eggs were placed in the vials walls. Number of emerged adults (F1 was similar between DE and kaolin; hence, kaolin constitutes a promising tool to the management of Z. subfasciatus. The mixture of kaolin and neem oil was not efficient in the control of Z. subfasciatus.O caruncho-do-feijão Zabrotes subfasciatus (Coleoptera: Chrysomelidae: Bruchinae é uma importante praga de grãos de feijão armazenado nas regiões tropicais. A eficiência do caulim [com ou sem óleo de nim (Azadirachta indica] e terra diatomácea (TD (tratamento padrão foi estudada em laboratório com o intuito de obter alternativas para o controle químico deste inseto. Insetos foram confinados em frascos de plástico com feijão tratado com caulim (2, 4 e 8g kg-1, caulim + nim [2g kg-1(5% óleo de nim], terra diatomácea (1g kg-1 e controle. Mortalidade de insetos adultos, número de ovos e emergência da geração F1 foram avaliados. Caulim causou a mortalidade de Z. subfasciatus, porém foram necessários maiores períodos e doses que a TD para promover elevada mortalidade (100% ou aproximadamente. Os tratamentos com caulim também afetaram o comportamento da f

Use of kaolin as a potential low-cost adsorbent for the removal of malachite green from colored effluents

Energy Technology Data Exchange (ETDEWEB)

Foletto, E.L.; Caponi, N.; Collazzo, G.C.; Jahn, S.L.; Dotto, G.L.; Mazutti, M.A. [Universidade Federal de Santa Maria (UFSM), RS (Brazil)

2016-07-01

Full text: This study investigated the potential of raw kaolin as a low-cost adsorbent for the removal Malachite Green (MG) from colored effluents. The morphology, chemical structure and the surface properties of the adsorbent were investigated by characterization techniques such as X-ray diffraction, N2 adsorption-desorption isotherms, Fourier transform infrared spectroscopy, X-ray fluorescence spectroscopy and scanning electron microscopy. A possible technological application of kaolin is the MG removal from aqueous media, which was investigated by batch adsorption experiments. The adsorption kinetics was studied using the pseudo-first order, pseudo-second order and Elovich models. The adsorption isotherms were studied using Langmuir, Freundlich and Sips models. Maximum adsorption capacity was found to be 128 mg g-1, and this satisfactory result may be associated to some properties of adsorbent. Therefore, the results of this investigation revealed that kaolin can be utilized as a promising low-cost adsorbent to remove MG from colored effluents. (author)

Correlation between hardness and water absorption properties of Saudi kaolin and white clay geopolymer coating

Science.gov (United States)

Ramasamy, Shamala; Abdullah, Mohd Mustafa Al Bakri; Huang, Yue; Hussin, Kamarudin; Wang, Jin; Shahedan, Noor Fifinatasha

2017-09-01

Geopolymer is an uprising technology that is being studied worldwide. Geopolymer raw materials are basically aluminosilicate source materials. However, this technology is yet to infiltrate into pipelines and coating industries which initiated our research idea. The idea of creating universal geopolymer based coating material is mainly to help oil and gas industry reduce its maintenance cost. Kaolin based geopolymer paste was coated on glass reinforced epoxy (GRE) substrates which are majorly used as pipeline material in the oil and gas industry at Saudi Arabia. Kaolin and white clay was chosen as raw material to study the possibilities of utilizing underused aluminosilicate raw materials for geopolymer coating. To obtain suitable formulation, Na2SiO3/NaOH ratio was varied from 0.40 untill 0.60 while other parameters such as solid/liquid ratio and NaOH molarity were kept constant at values as per previous works. Geopolymer coated GRE substrates were then subjected to water absorption, flexural strength and hardness test to validate our findings. Water absorption is a crucial test as for coating materials which justifies the pratical usability of the coating product. Upon testing, kaolin and white clay based geopolymer coating each shows promising properties at Na2SiO3/NaOH ratio of 0.45 and 0.50 each.

Simultaneous removal of organic contaminants and heavy metals from kaolin using an upward electrokinetic soil remediation process

International Nuclear Information System (INIS)

Wang, J.-Y.; Huang, X.-J.; Kao, Jimmy C.M.; Stabnikova, Olena

2007-01-01

Kaolins contaminated with heavy metals, Cu and Pb, and organic compounds, p-xylene and phenanthrene, were treated with an upward electrokinetic soil remediation (UESR) process. The effects of current density, cathode chamber flushing fluid, treatment duration, reactor size, and the type of contaminants under the vertical non-uniform electric field of UESR on the simultaneous removal of the heavy metals and organic contaminants were studied. The removal efficiencies of p-xylene and phenanthrene were higher in the experiments with cells of smaller diameter or larger height, and with distilled water flow in the cathode chamber. The removal efficiency of Cu and Pb were higher in the experiments with smaller diameter or shorter height cells and 0.01 M HNO 3 solution as cathode chamber flow. In spite of different conditions for removal of heavy metals and organics, it is possible to use the upward electrokinetic soil remediation process for their simultaneous removal. Thus, in the experiments with duration of 6 days removal efficiencies of phenanthrene, p-xylene, Cu and Pb were 67%, 93%, 62% and 35%, respectively. The experiment demonstrated the feasibility of simultaneous removal of organic contaminants and heavy metals from kaolin using the upward electrokinetic soil remediation process

Uranium in mining water of kaolin open pit in Zarów (Lower Silesia); methodology of determination and genetic remarks.

Science.gov (United States)

Chau, N D; Wyszomirski, P; Chruściel, E; Ochoński, A

1999-11-01

In this paper, a method of determination of uranium 238 and 234 in mining waters of Andrzej kaolin open pit in Zarów (Lower Silesia) is presented. The method is based on independent measurements of alpha and beta radiation intensities by means of a liquid scintillation spectrometer alpha/beta. The initial volume of water sample was 3 dm3, then it was diminished by chemical preparation to 6 cm3, and then 12 cm3 of scintillator was added. The lower limit of detection (for the measurement time of 8 h) for both 234U and 238U amounted to 0.02 Bq/dm3. For determination of the uranium content in ferruginous sediments precipitating from mining waters of the above-mentioned open pit, gamma ray spectrometry was used. The obtained results may be viewed as a contribution to studies on anomalous uranium concentration within this kaolin deposit. The elevated uranium content, in comparison with its average concentration in the Earth crust, is characteristic for parent rocks of Andrzej kaolin deposit, which are granitoids of Strzegom-Sobótka massif. In connection with it, the high uranium content can be observed not only in kaolin and weakly kaolinised granitoids from the deposit in question, but also in mining waters genetically related with them.

Effects of using kaolin waste and granite waste as raw materials for the production of low-water absorption ceramic tiles

International Nuclear Information System (INIS)

Freires, H.P.; Argonz, R.; Nogueira, R.E.F.Q.; Sasaki, J.M.; Sales, J.C.

2012-01-01

This study aims to evaluate the potential of co-use of granite waste (Rain Forest) and kaolin waste as raw material for the manufacture of ceramic coating of low water absorption. Raw materials were characterized by X-ray diffraction. Kaolin residue was added to the residue of granite in the following proportions (in wt%): 0, 10, 20, 30, 40 and 50%. Specimens were fabricated by uniaxial pressing and fired at 1175,1200 and 1225 deg C. Studies of firing linear shrinkage, water absorption, apparent porosity, apparent density and tensile bending test (or rupture modulus) were conducted. The temperature of 1225 deg C allowed the use of a mixture of 50% granite residue and 50% kaolin residue. Ceramic parts made from that mixture exhibited the maximum values required by the Brazilian Standard NBR 13818 for water absorption, shrinkage and density. (author)

Influence of Kaolin in Fly Ash Based Geopolymer Concrete: Destructive and Non-Destructive Testing

Science.gov (United States)

Yahya, Z.; Abdullah, M. M. A. B.; Ramli, N. Mohd; Burduhos-Nergis, D. D.; Razak, R. Abd

2018-06-01

Development of geopolymer concrete is mainly to reduce the production of ordinary Portland cement (OPC) that adverse the natural effect. Fly ash is a by-product collected from electrical generating power plant which resulted from burning pulverized coal. Since fly ash is waste materials, it can be recycled for future advantages particularly as pozzolanic materials in construction industry. This study focused on the feasibility of fly ash based geopolymer concrete to which kaolin has been added. The main constituents of geopolymer production for this study were class F fly ash, sodium silicate and sodium hydroxide (NaOH) solution. The concentration of NaOH solution was fixed at 12 Molar, ratio of fly ash/alkaline activator and sodium silicate/NaOH fixed at 1.5 and 2.5, respectively. Kaolin was added in range 5% to 15% from the mass of fly ash and all the samples were cured at room temperature. Destructive and non-destructive test were performed on geopolymer concrete to evaluate the best mix proportions that yield the highest strength as well as the quality of the concrete. Compressive strength, flexural strength, rebound hammer and ultrasonic pulse velocity (UPV) result have been obtained. It shown that 5% replacement of kaolin contributed to maximum compressive strength and flexural strength of 40.4 MPa and 12.35 MPa at 28 days. These result was supported by non-destructive test for the same mix proportion.

Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

Science.gov (United States)

Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

2017-04-01

sand from kaolin-washing process is of several hundred thousand tonnes and it thus represent so far a relatively rarely used natural building material which is currently usually deposited in worked-out areas of kaolin quarries. One of the main reasons of very difficult usability of this sands in building material industry is their behavior when exposed to the weather. In only a very short time of exposure in outdoor condition they may change in colour from greyish white to yellow-brown or golden yellow. This colour change is accompanied by significant decrease of pH values of sand leachate up to pH ranging between 3.5 and 5.5, in extreme cases even up to 2.0. Despite these extreme chemical properties of sands under study, the artificial sandstone, very similar in the physical and mechanical properties to natural ones, was successfully prepared in the laboratory. Due to the mineralogical composition of applied sands (i.e. the presence not only of quartz, but also of feldspar and muscovite), the artificial sandstone is characterized by relatively true natural appearance.

Synthesis of zeolite using as precursor reject of kaolin of the Amazon Region: application as an adsorbent in gas drying

International Nuclear Information System (INIS)

Morais, M.R.C.; Santana, D.L. de; Martelli, M.C.; Neves, R.F.

2011-01-01

Zeolites have large variety of technological applications, accounting for an increasing interest in various industries. In the State of Para, located three industries from kaolin for paper, where large amounts of waste are stored in ponds in becoming environmental problem. This work aims to develop a process for obtaining a zeolite P from the kaolin waste as the starting material. The synthesis was performed with kaolin waste from Capim River region, calcined at 700 ° C for 2 h, and reacted in the presence of aqueous NaOH and diatomite (silica source supplement), and the process hydrothermal temperature of 110 ° C for varied times. The characterization of the starting material and the synthesized materials was carried out using XRD and SEM. At the end of the experiment, the zeolite P synthesized was tested for moisture adsorption and was effective for this purpose. (author)

Incorporation of waste and fiber kaolin caroa panels in Medium Density Fiberboard - MDF

International Nuclear Information System (INIS)

Bezerra, A.F.C.; Santana, L.N.L.; Neves, G.A.; Carvalho, L.H. de; Lopes, F.F.M.

2012-01-01

Medium-density panels are composites molded under high temperature and pressure which have physical and mechanical properties similar to those of solid wood. Their composition includes eucalyptus grandis fibers and pinus elliotii fibers, but other fibers can be used such as caroa fibers. The goal of this work was to manufacture panels which kaolin waste and caroa fibers and compare their physical, chemical and mechanical of these panels with a others. Both residue and the fibers were characterized by: differential thermal analysis, thermal gravimetric analysis and Xray diffraction. Through the process of pressing the test specimens were fabricated, test samples were evaluated by three point bending, internal bond, water absorption and swelling in thickness. The samples have low levels of thickness swelling, flexural strength and higher tensile and absorption content relative to commercial MDF. (author)

Synthesis and characterization of zeolite NaP using kaolin waste as a source of silicon and aluminum

Energy Technology Data Exchange (ETDEWEB)

Hildebrando, Edemarino Araujo, E-mail: edemarino@ufpa.br [Universidae Federal do Para (UFPA), Maraba, PA (Brazil). Fac. de Engenharia de Materias. Lab. de Materiais Ceramicos; Andrade, Christiano Gianesi Bastos; Valenzuela-Diaz, Francisco Rolando [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Dept. de Metalurgia e Engenharia de Materiais; Rocha Junior, Carlos Augusto Ferreira da; Neves, Roberto de Freitas [Universidae Federal do Para (UFPA), Maraba, PA (Brazil). Int. de Tecnologia. Fac. de Engenharia Quimica; Angelica, Romulo Simoes [Universidae Federal do Para (UFPA), Maraba, PA (Brazil). Inst. de Geociencias. Fac. de Geologia

2014-08-15

The synthesis of zeolite NaP using kaolin waste, from the Amazon region, as a predominant source of silicon and aluminum has been studied. The zeolitisation process occurred in hydrothermal conditions using static autoclaving and the effects of time, temperature, and the Si/Al ratio were investigated. The starting material and the phases formed as reaction products were characterized by XRD, SEM and FTIR. The results showed that pure zeolite NaP is hydrothermally synthesized, at 100 °C for 20 hours, using meta kaolin waste material in alkaline medium in presence of additional silica. The XRD and SEM analyses indicate that the synthesized zeolite presents good crystallinity. (author)

Synthesis and characterization of zeolite NaP using kaolin waste as a source of silicon and aluminum

International Nuclear Information System (INIS)

Hildebrando, Edemarino Araujo; Andrade, Christiano Gianesi Bastos; Valenzuela-Diaz, Francisco Rolando; Rocha Junior, Carlos Augusto Ferreira da; Neves, Roberto de Freitas; Angelica, Romulo Simoes

2014-01-01

The synthesis of zeolite NaP using kaolin waste, from the Amazon region, as a predominant source of silicon and aluminum has been studied. The zeolitisation process occurred in hydrothermal conditions using static autoclaving and the effects of time, temperature, and the Si/Al ratio were investigated. The starting material and the phases formed as reaction products were characterized by XRD, SEM and FTIR. The results showed that pure zeolite NaP is hydrothermally synthesized, at 100 °C for 20 hours, using meta kaolin waste material in alkaline medium in presence of additional silica. The XRD and SEM analyses indicate that the synthesized zeolite presents good crystallinity. (author)

Síntese e caracterização de hidrogéis compósitos a partir de copolímeros acrilamida-acrilato e caulim: efeito da constituição de diferentes caulins do nordeste brasileiro Synthesis and characterization of poly (acrylamide-co-acrylate and kaolin hydrogel composites: effect of the constitution of different kaolins from northeastern Brazil

Directory of Open Access Journals (Sweden)

Carlos W. de Q. Brito

2013-01-01

Full Text Available Superabsorbent hydrogels based on poly (acrylamide-co-acrylate and different kaolins, were prepared by free-radical aqueous copolymerization. FTIR and WAXS techniques were employed for characterization of a series of hydrogels, obtained by varying the percentage of clay, crosslinking and constitution of kaolin. The water absorbency at equilibrium (Weq decreased with increasing clay content and the amount of crosslinking agent. Superabsorbent hydrogel (Weq > 1084 g H2O/g gel was obtained as 10 wt% of white kaolin and 0.05 mol% of crosslinking agent were used. The hydrogel proved sensitive to pH variation and the presence of salts.

Partitioning of hexachlorobenzene in a kaolin/humic acid/surfactant/water system: Combined effect of surfactant and soil organic matter

Energy Technology Data Exchange (ETDEWEB)

Wan, Jinzhong; Wang, Lingling [Environmental Science Research Institute, Huazhong University of Science and Technology, Wuhan 430074 (China); Lu, Xiaohua, E-mail: hust-esri2009@hotmail.com [Environmental Science Research Institute, Huazhong University of Science and Technology, Wuhan 430074 (China); Lin, Yusuo; Zhang, Shengtian [Nanjing Institute of Environmental Science, Ministry of Environmental Protection of China, Nanjing 210042 (China)

2011-11-30

Highlights: Black-Right-Pointing-Pointer We study HCB partitioning in a kaolin/humic acid/TX100/water system. Black-Right-Pointing-Pointer We reveal influence of TX100-HA interaction on TX100 and HA sorption to kaolin. Black-Right-Pointing-Pointer We verify combined effect of TX100 and HA on HCB desorption from clay. - Abstract: Understanding the combined effect of soil organic matter (SOM) and surfactants on the partitioning of hydrophobic organic compounds in soil/water systems is important to predict the effectiveness of surfactant-enhanced remediation (SER). In the present study we investigate the partitioning of hexachlorobenzene (HCB) within a humic acid (HA)-coated kaolin/Triton X-100 (TX100)/water system, with special emphasis on the interaction between TX100 and HA, and their combined effect on HCB sorption. HA firstly enhanced then suppressed TX100 sorption to kaolin as the amounts of HA increased, while the addition of TX100 led to a consistent reduction in HA sorption. In the HA-coated kaolin/TX100/water system, TX100 played a primary role in enhancing desorption of HCB, while the role could be suppressed and then enhanced as HA coating amounts increased. Only at HA coating above 2.4%, dissolved HA outcompeted clay-bound HA for HCB partitioning, resulting in dissolved HA enhanced desorption. The presence of dissolved HA at these conditions further promoted the effectiveness of TX100 enhanced desorption. Despite a reduced TX100 sorption to clay was achieved due to the presence of dissolved HA, the effect on HCB desorption was comparatively slight. A reliable cumulative influence of HA and TX100 on HCB desorption was observed, although HCB desorption by HA/TX100 mixed was less than the sum of HA and TX100 individually. Our study suggests that for soils of high organic contents, the combined effect of SOM and surfactants on HOCs desorption can be applied to improve the performance of SER.

Application of molybdenum and phosphate modified kaolin in electrochemical treatment of paper mill wastewater

International Nuclear Information System (INIS)

Ma Hongzhu; Wang Bo; Wang Ying

2007-01-01

Pulp and paper mill wastewater is characterized by very high chemical oxygen demand (COD) values that inhibit the activity of microorganisms during biological oxidations. The electrochemical degradation of pulp and paper mill wastewater catalyzed by molybdenum and phosphate (Mo-P) modified kaolin with graphite as anode and cathode was investigated. The catalyst was characterized by XRD, XPS and SEM spectra and the effects of pH, metal ion and introduction of NaCl on the efficiency of the electrochemical degradation process were also studied. It was found out that the modified kaolin loaded with Fe 3+ had higher electrochemical catalytic activity in the electrochemical degradation of paper mill wastewater at pH 4. A 96% COD removal efficiency was obtained in 40 min of electrochemical treatment of the wastewater at current density 30 mA cm -2 . A possible mechanism for degradation of the mill wastewater constituents was also proposed

Adsorpce toxických oxoaniontů Se na povrchově upravený kaolin

Czech Academy of Sciences Publication Activity Database

Herzogová, L.; Doušová, B.; Lhotka, M.; Machovič, Vladimír; Schweigstillová, Jana; Koloušek, D.

2012-01-01

Roč. 106, č. 8 (2012), s. 759-764 ISSN 0009-2770 Institutional research plan: CEZ:AV0Z30460519 Keywords : adsorption * oxoanions Se * surface-modified kaolins Subject RIV: CA - Inorganic Chemistry Impact factor: 0.453, year: 2012 http://www.chemicke-listy.cz/docs/full/2012_08_759-764.pdf

Kaolin particle films suppress many apple pests, disrupt natural enemies and promote woolly apple aphid

NARCIS (Netherlands)

Markó, V.; Blommers, L.H.M.; Bogya, S.; Helsen, H.H.M.

2008-01-01

Multiple applications of hydrophobic kaolin particle film in apple orchards suppressed numbers of blossom weevil (Anthonomus pomorum), brown leaf weevil (Phyllobius oblongus), attelabid weevil (Caenorhinus pauxillus), leafhoppers (Empoasca vitis and Zygina flammigera) and green apple aphid (Aphis

Investigation of the effect of kaolin and tissue factor-activated citrated whole blood, on clot forming variables, as evaluated by thromboelastograph

DEFF Research Database (Denmark)

Johansson, Per Ingemar; Bochsen, L.; Andersen, S.

2008-01-01

), and maximum clot strength (amplitude [MA]) were evaluated, together with day-to-day variation, the coefficient of variance (CV%), and the effect of citrate storage time. RESULTS: Clot formation variables were equally affected by TF 1:17,000 and kaolin activation, whereas R was significantly longer when TF 1......:42,500 was used. The CV for the different variables varied from 3 to 13 percent with no significant differences between assays. Storage of citrated WB significantly affected the TEG variables in a hypercoagulable direction. Only the R, however, was significantly affected (12%) when samples rested for 0 and 30...... minutes were evaluated with kaolin as the activator. CONCLUSION: The TEG assays evaluated were reproducible and present with an acceptable CV% for routine clinical practice. Kaolin and TF 1:17,000 equally affected the clot formation variables. Storage of WB for up to 30 minutes in citrate did not, except...

Sample size clay kaolin of primary in pegmatites regions Junco Serido - PB and Equador - RN; Granulometria de argila caulim primario dos pegmatitos nas regioes do Junco do Serido - PB e Equador - RN

Energy Technology Data Exchange (ETDEWEB)

Meyer, M.F.; Sousa, J.B.M.; Sales, L.R.; Silva, P.A.S.; Lima, A.D.D., E-mail: mauro.meyer@ifrn.edu.br [Instituto Federal do Rio Grande do Norte (IFRN), RN (Brazil)

2016-07-01

Kaolin is a clay formed mainly of kaolinite resulting from feldspar weathering or hydrothermal. This study aims to investigate the way of occurrence, kaolin particle size of the pegmatites of the Borborema Province Pegmatitic in the regions of Junco do Serido-PB and Ecuador-RN. These variables were analyzed considering granulometric intervals obtained from wet sieving of samples of pegmatite mines in the region. Kaolin was received using sieves of 200, 325, 400 and 500 mesh and the sieve fractions retained by generating statistical parameters histograms. kaolin particles are extremely fine and pass in its entirety through 500 mesh sieve. The characterization of minerals in fine fractions by diffraction of X-rays showed that the relative amount of sericite in fractions retained in sieves 400 and 500 mesh impairing the whiteness and mineralogical texture kaolin production. (author)

Deposition of waste kaolin in aluminum alloy by electrolytic plasma technique

International Nuclear Information System (INIS)

Palinkas, Fabiola Bergamasco da Silva Marcondes; Antunes, Maria Lucia Pereira; Cruz, Nilson Cristino; Rangel, Elidiane Cipriano; Souza, Jose Antonio da Silva

2016-01-01

Full text: Kaolin is a widely explored mineral for various industrial purposes and its processing generates up to 90% of waste, corresponding to 500 thousand tons annually. The Deposition of Kaolin residue on aluminum alloys by electrolytic plasma has objective of a valorization of the residue. It was evaluated the mineralogical composition by X-ray diffraction (XRD), using PANalytical diffractometer X'Pert Pro. The scanning electron microscopy (SEM) and the spectrometry of dispersive of energy (EDS) evaluated the morphology and elementary chemical composition by microscope scanning electron JEOL JSM-6010LA. The Infrared Spectroscopy (FTIR) has used a Spectrometer the Perkin-Elmer 1760X FT-IR with spectral range 4000-400 cm -1 . XRD results indicate peaks of kaolinite as the main constituent. The morphology of the particles correspond to pseudo-hexagonal lamellar crystals characteristic of kaolinite, analysis by EDS allows to identify the composition of the particles as Al and Si. The samples were deposited at concentrations of 5, 10 and 15 mg of the residue and each concentration were considered deposition times of 5, 10 and 15 minutes. Tests evaluate the films as the wettability, chemical composition, morphology, mechanical strength and corrosion resistance. Results indicate the presence of kaolinite, alumina and mullite in the obtained coatings. (author)

Comparing Kaolin and Pinolene to Improve Sustainable Grapevine Production during Drought

OpenAIRE

Brillante, Luca; Belfiore, Nicola; Gaiotti, Federica; Lovat, Lorenzo; Sansone, Luigi; Poni, Stefano; Tomasi, Diego

2016-01-01

Viticulture is widely practiced in dry regions, where the grapevine is greatly exposed to water stress. Optimizing plant water use efficiency (WUE) without affecting crop yield, grape and wine quality is crucial to limiting use of water for irrigation and to significantly improving viticulture sustainability. This study examines the use in vineyards of particle film technology (engineered kaolin) and compares it to a film-forming antitranspirant (pinolene), traditionally used to limit leaf wa...

Numerical analyses of caisson breakwaters on soft foundations under wave cyclic loading

Science.gov (United States)

Wang, Yuan-zhan; Yan, Zhen; Wang, Yu-chi

2016-03-01

A caisson breakwater is built on soft foundations after replacing the upper soft layer with sand. This paper presents a dynamic finite element method to investigate the strength degradation and associated pore pressure development of the intercalated soft layer under wave cyclic loading. By combining the undrained shear strength with the empirical formula of overconsolidation clay produced by unloading and the development model of pore pressure, the dynamic degradation law that describes the undrained shear strength as a function of cycle number and stress level is derived. Based on the proposed dynamic degradation law and M-C yield criterion, a dynamic finite element method is numerically implemented to predict changes in undrained shear strength of the intercalated soft layer by using the general-purpose FEM software ABAQUS, and the accuracy of the method is verified. The effects of cycle number and amplitude of the wave force on the degradation of the undrained shear strength of the intercalated soft layer and the associated excess pore pressure response are investigated by analyzing an overall distribution and three typical sections underneath the breakwater. By comparing the undrained shear strength distributions obtained by the static method and the quasi-static method with the undrained shear strength distributions obtained by the dynamic finite element method in the three typical sections, the superiority of the dynamic finite element method in predicting changes in undrained shear strength is demonstrated.

Mineralizer effects on mullite formation from kaolin processing wastes in Para-Brazil

International Nuclear Information System (INIS)

Martelli, Marlice Cruz; Angelica, Romulo Simoes; Neves, Roberto de Freitas

2009-01-01

Mullite is a relatively rare mineral in nature, formed under exceptional conditions of high temperature and pressure, which can be used to synthesize this mineral. Mullite presents good chemical and thermal stability among others properties that explain the importance of mullite in traditional and advanced ceramics. This research proposes the development of a process to synthesize mullite using the wastes from kaolin processing industries located in the Rio Jari (Monte Dourado-PA) and Rio Capim (Ipixuna-PA) districts. The synthesized materials will be studied for application as silicon-aluminum refractory bricks. The steps are mineralogical and chemical characterization, verifying the differences between the materials processing through firing of the wastes at increasing levels of temperature with 100 deg C increments, ranging from 600 to 1000 deg C and 1200 to 1500 deg C, during 3 hours at each level. Methods include the study of temperature and impurities effects through X-ray-powder and scanning electron microscopy. (author)

Influence of kaolin and firing temperature on the mullite formation in porous mullite-corundum materials

International Nuclear Information System (INIS)

Mahnicka, L; Svinka, R; Svinka, V

2011-01-01

The refractory ceramics became very important in both the traditional and the advanced materials applications as it has outstanding thermal and mechanical properties. The refractoriness of ceramics can be achieved by getting the mullite-corundum. Refractory ceramics with high porosity serve as a heat insulator and constructional material. Three series of porous mullite-corundum ceramic samples were prepared from Al 2 O 3 (Nabalox, Germany) and pure SiO 2 in 2.57:1 ratio that was conformed to mullite compositions (3Al 2 O 3 ·2SiO 2 ). α-Al 2 O 3 (d 50 = 4 μm) and γ-Al 2 O 3 (d 50 = 80 μm) were in 1:3 ratio. Quantity of kaolin (MEKA, Germany) was 10, 20 and 30 wt.%. Porous materials were prepared by slip casting of suspension of raw materials, where the aluminium paste (0.18 wt.%) was used as a pore former. Water content in the suspensions was 38-40 wt.%. Pore formation occured in result of hydrogen formation in chemical reaction between aluminium paste and water. The samples were sintered at 1650, 1700 and 1750°C temperature for one hour. SiO 2 and γ-Al 2 O 3 on the contrary reduced mechanical properties, but decreased shrinkage. Using of α-, γ-Al 2 O 3 , SiO 2 and kaolin in corresponding ratios the samples with open porosity of 30 to 54 vol% were acquired. The relative amounts of pores depended on the initial content of kaolin and on firing temperature.

Determination of the zero point of charge of kaolin waste from the Northeast of Para, BR

International Nuclear Information System (INIS)

Pinto, R.L.S.; Maia, R.F.S.; Felipe, A.M.P.F.

2012-01-01

The Para contributes with more than 50% of national production of kaolin of which 12.5% correspond to the waste generated, which has similar composition to benefited kaolin, can be used as adsorbent of heavy metals. The viscosity influences the design of equipment that can reuse that waste. The pH changes the pulp viscosity and the determination of the zero point of charge can estimate this variation. This study analyzes the influence of pH on the pulp rheology by the determination of the zero point of charge. Tests were made by Scanning Electron Microscopy, Energy Dispersive Spectroscopy, potentiometric titulation and rheological analysis. The results showed zero point of charge equal to 3.7 and confirmed that the viscosity increase at pH values near the zero point of charge and decrease at pH values away from this. (author)

Assessment of the adsorptive capacity of the Kaolin deposit targeting its use on the removal of colors in aqueous solution; Avaliacao da capacidade adsortiva do rejeito de caulim visando seu uso na remocao de corantes em solucao aquosa

Energy Technology Data Exchange (ETDEWEB)

Matos, S.C.; Hildebrando, E.A., E-mail: matos.cintia68@gmail.com [Universidade Federal do Para (FEMat/UFPA), PA (Brazil). Faculdade de Engenharia de Materiais

2016-07-01

The Amazonic region has large and valuable kaolin deposits. The state of Para by itself comprises three large industries which process kaolin. It has been noticed that the waste resulting from the processing of kaolin is rich in silico-aluminate, presenting potential in adsorption processes. Thus, this research's objective is to assess the kaolin waste produced during the processing phase, aiming at its application as low cost adsorbent material. For that, the kaolin waste has been characterized by X-ray diffraction and chemical analysis (XRF), and then sieved and calcined at 700 ° C, being then subjected to the adsorption process and observed qualitatively its capacity of retention by methylene blue (AM). Preliminary results show that the kaolin waste has satisfactory adsorption capacity at concentrations of up to 50.0 mg / MP, demonstrating the potential that it be used in the removal of dyes in wastewater treatment. (author)

Heavy mineral as a tool to refine the stratigraphy of kaolin deposits in the Rio Capim Area, Northern Brazil

Directory of Open Access Journals (Sweden)

Ana M. Góes

2007-09-01

Full Text Available Studies of heavy minerals in kaolin deposits from the Ipixuna Formation in the Rio Capim area (Northern Brazil showed a mature to super mature assemblage dominated by zircon and tourmaline, and subordinately rutile, kyanite and staurolite. These minerals do not change much throughout the whole section; however, each kaolin unit displays a particular signature, defined by differences in the proportions of the whole assemblage of heavy minerals, as well as of their textural characteristics. This work revealed that the lower and upper kaolin units can be definitely considered as distinct depositional sequences. A higher proportion of opaque minerals and higher zircon values characterize the lower unit. The higher volumes of anhedric, rounded to sub-rounded grains of zircon and tourmaline in the upper unit suggests that this includes grains that were undergone to a higher degree of reworking. The increased volume of unaltered staurolite and kyanite in the upper unit leads to conclude that, even considering sediment reworking, a distinct source must be invoked. The results also show that the characteristics of the heavy mineral assemblage from the intermediate unit are comparable with those from the upper unit, which suggests they might record a same stratigraphic sequence.Estudos de minerais pesados provenientes em depósitos cauliníticos da Formação Ipixuna na região do rio Capim (Brasil revelaram uma mineralogia matura a supermatura, representada dominantemente por zircão e turmalina e, subordinadamente, rutilo, cianita e estaurolita. Os minerais encontrados não variam muito, entretanto cada unidade caulinítica apresenta uma assinatura particular definida por diferenças nasproporções entre os principais minerais, assim como em suas características texturais. Este trabalho demonstrou que asunidades de caulim soft (inferior e semi-flint (superior podem ser consideradas seqüências deposicionais distintas. As altas percentagens de opacos

Methane reacts with heteropolyacids chemisorbed on silica to produce acetic acid under soft conditions

KAUST Repository

Sun, Miao; Abou-Hamad, Edy; Rossini, Aaron J.; Zhang, Jizhe; Lesage, Anne; Zhu, Haibo; Pelletier, Jeremie; Emsley, Lyndon; Caps, Valerie; Basset, Jean-Marie

2013-01-01

Selective functionalization of methane at moderate temperature is of crucial economic, environmental, and scientific importance. Here, we report that methane reacts with heteropolyacids (HPAs) chemisorbed on silica to produce acetic acid under soft

Synthesis and characterization of ZSM-5 and calcined kaolin evaluation using the content of structure-directing

International Nuclear Information System (INIS)

Rodrigues, J.J.; Silva, V.J. da; Rodrigues, M.G.F.

2012-01-01

This study aims to evaluate the effect of the structure-directing content, tetrapropylammonium bromide, on the structural and morphological characteristics of ZSM-5 zeolite obtained using calcined kaolin as silicon and aluminum. The samples were characterized by XRD, EDX, SEM and Physics Adsorption N 2 . Trough X ray diffraction patterns was possible to observed the formation of the structure of ZSM-5 with intense peaks and well-defined characteristic of crystalline. The micrographs showed that the samples consist of agglomerates and/or aggregates of particles characteristic of the MFI structure typical of ZSM-5 zeolite. And through the adsorption-desorption isotherms physical N2 was possible to observe that the samples show hysteresis type I typical of microporous materials with specific surface areas of 218 and 222 m 2 /g. Therefore, the use of calcined kaolin to obtain ZSM-5 zeolite was effective. (author)

Study of the sodalite Bayer synthesis process from reject of kaolin of the Amazon region, Brazil

International Nuclear Information System (INIS)

Maia, A.A.B.; Neves, R.F.; Angelica, R.S.; Pöllmann, H.

2011-01-01

This work presents an application for the kaolin rejects from Amazonia through the synthesis of sodalite, in addition, the series of sodalites was synthesized with the same conditions of the Bayer process to understand and control their formation when necessary. These tailings are generated by companies located in the state of Para and are mainly composed of kaolinite, thus forming an excellent starting material for the production of zeolites. The synthesis process was carried out in autoclaves and two synthesis temperatures, 150 and 200 deg C, were evaluated, the same ones used in the Bayer process. The anions used in the reaction mixture to obtain the sodalite series were: carbonate chloride and sulfate, and NaOH solution was used as the sodium source. Sodalite was produced in all the synthesis conditions, showing that through the kaolin rejects from the Amazon it was possible to study the sodalite synthesis process.

On guided circumferential waves in soft electroactive tubes under radially inhomogeneous biasing fields

Science.gov (United States)

Wu, Bin; Su, Yipin; Chen, Weiqiu; Zhang, Chuanzeng

2017-02-01

Soft electroactive (EA) tube actuators and many other cylindrical devices have been proposed recently in literature, which show great advantages over those made from conventional hard solid materials. However, their practical applications may be limited because these soft EA devices are prone to various failure modes. In this paper, we present an analysis of the guided circumferential elastic waves in soft EA tube actuators, which has potential applications in the in-situ nondestructive evaluation (NDE) or online structural health monitoring (SHM) to detect structural defects or fatigue cracks in soft EA tube actuators and in the self-sensing of soft EA tube actuators based on the concept of guided circumferential elastic waves. Both circumferential SH and Lamb-type waves in an incompressible soft EA cylindrical tube under inhomogeneous biasing fields are considered. The biasing fields, induced by the application of an electric voltage difference to the electrodes on the inner and outer cylindrical surfaces of the EA tube in addition to an axial pre-stretch, are inhomogeneous in the radial direction. Dorfmann and Ogden's theory of nonlinear electroelasticity and the associated linear theory for small incremental motion constitute the basis of our analysis. By means of the state-space formalism for the incremental wave motion along with the approximate laminate technique, dispersion relations are derived in a particularly efficient way. For a neo-Hookean ideal dielectric model, the proposed approach is first validated numerically. Numerical examples are then given to show that the guided circumferential wave propagation characteristics are significantly affected by the inhomogeneous biasing fields and the geometrical parameters. Some particular phenomena such as the frequency veering and the nonlinear dependence of the phase velocity on the radial electric voltage are discussed. Our numerical findings demonstrate that it is feasible to use guided circumferential

Fly ash/Kaolin based geopolymer green concretes and their mechanical properties

Directory of Open Access Journals (Sweden)

F.N. Okoye

2015-12-01

Full Text Available Geopolymer concrete mixes were cast using fly ash, kaolin, sodium hydroxide, potassium hydroxide, sodium silicate and aggregates. Portland cement concrete (M30 was used as a reference sample. The effect of silica fume, temperature (40 °C, 60 °C, 80 °C, 100 °C and 120 °C, sodium and potassium hydroxides and different superplasticizers on the compressive strength are reported [1]. Maximum strength was found at 100 °C and 14 M alkali solution [1].

Electrokinetic remediation of heavy metals contaminated kaolin by a CNT-covered polyethylene terephthalate yarn cathode

International Nuclear Information System (INIS)

Yuan, Lizhu; Li, Haiyan; Xu, Xingjian; Zhang, Jing; Wang, Nana; Yu, Hongwen

2016-01-01

In the current study, carbon nanotube (CNT) covered polyethylene terephthalate yarns (PET-CNT) electrode has been investigated as a novel cathode material for the electrokinetic (EK) remediation of multi-metals (Cd, Cu, Ni, Pb, Zn) contaminated kaolin. The results of scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) showed that CNT was successfully covered on the surface of PET. The results obtained from EK process showed that PET-CNT as a cathode obviously elevated electric current and electro-osmotic flow (EOF), significantly decreased kaolin pH, and enhanced heavy metals removal efficiencies. The removal efficiencies of Cd, Cu, Ni, Pb, and Zn in PET-CNT treatment were 89.7%, 63.6%, 90.7%, 19.2%, and 88.7%, respectively. In comparison with the Pt/Ti and graphite treatments, the removal efficiencies of Cd, Ni, and Zn were improved at least about 30%, Cu and Pb were improved at least 16.6% and 6.9%, respectively. Our results demonstrated the PET-CNT was a good alternative cathode material for enhancing efficiency of EK remediation.

Effect of Rice Husk and Diatomite on the Insulating Properties of Kaolin - Clay Firebricks

Directory of Open Access Journals (Sweden)

Emmanuel Ogo ONCHE

2007-09-01

Full Text Available This work was carried out to investigate the effect of rice husk and diatomite on the insulating properties of kaolin-clay firebrick. Five firebrick samples of different compositions were fired at 900°C, 1000°C, 1100°C, and 1200°C. Samples A-E are all insulating firebricks that can withstand temperatures ranging from 900°C to 1200°C since none of the samples crumbled during firing. The results showed that they all had good insulating characteristics with their highly porous structure making them suitable for backup insulation. Mixing ratios of 3:2:4:1 representing weight in grams of kaolin, plastic clay, rice husk and diatomite respectively for sample D gave the optimum performance values in terms of modulus of rupture, apparent porosity, apparent density, bulk density, and thermal conductivity at all temperatures. At 1200°C, the values are 22.57kgf/cm2 for modulus of rupture, 98.25% for apparent porosity, 2.38g/cm3 for apparent density, 1.11g/cm3 for bulk density, and 0.038w/mK for thermal conductivity.

A fluorescence XAFS measurement instrument in the soft x-ray region toward observation under operando conditions

Energy Technology Data Exchange (ETDEWEB)

Honda, M., E-mail: honda.mitsunori@jaea.go.jp; Baba, Y.; Shimoyama, I.; Sekiguchi, T. [Quantum Beam Science Center, Japan Atomic Energy Agency (JAEA), 2-4 Shirakata-Shirane, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan)

2015-03-15

X-ray absorption fine structure (XAFS) measurements are widely used for the analysis of electronic structure. Generally, XAFS in the soft X-ray region is measured under vacuum, but chemical structures under vacuum are typically different from those under operando conditions, where chemical species exhibit their function. Here, we developed an XAFS measurement instrument, as a step toward operando fluorescent, which yields XAFS measurement using synchrotron radiation in the soft X-ray region. We applied this method to analyze the local electronic structure of the sulfur atoms in L-cysteine in different pH solutions. In water at pH 7, the hydrogen atom does not dissociate from the thiol (-SH) group in L-cysteine, which forms a structure surrounded by and interacting with water molecules. The XAFS spectrum of L-cysteine in solution was altered by changing the pH. At pH 9, the hydrogen atom dissociated and a thiolate anion was formed. Although the -SH group was oxidized to SO{sub 4}{sup 2−} when L-cysteine was adsorbed on a metal surface and dried, no oxidation was observed in solution. This may be because the water molecules were densely packed and protected the -SH group from oxidation. Our results show that this instrument aimed toward operando fluorescence XAFS measurements in the soft X-ray region is useful for structural analysis of sulfur atoms in organic molecules in air and in solution. The instrument will be applied to the structural analysis of materials containing elements that have absorption edges in soft X-ray region, such as phosphorus and alkali metals (potassium and cesium). It will be also particularly useful for the analysis of samples that are difficult to handle under vacuum and materials that have specific functions in solution.

Influence of the type of aqueous sodium silicate on the stabilization and rheology of kaolin clay suspensions

Science.gov (United States)

Izak, Piotr; Ogłaza, Longin; Mozgawa, Włodzimierz; Mastalska-Popławska, Joanna; Stempkowska, Agata

2018-05-01

To avoid agglomeration and sedimentation of grains, ceramic slurries should be modified by stabilizers in order to increase the electrostatic interactions between the dispersed particles. In this study we present the spectral analysis of aqueous sodium silicates obtained by different synthesis methods and their influence on the rheological properties of kaolin based slurries. Infrared and Raman spectra can be used to describe the structure of silicate structural units present in aqueous sodium silicates. It was confirmed that the best stabilization results possess aqueous sodium silicates of the silicate moduli of about 2 and the optimal concentration of the used fluidizer is 0.3 wt% to the kaolin clay dry mass. One of the most important conclusions is that the synthesis method of the fluidizer has no significant effect on its stabilization properties but used medium does create adequate stabilization mechanism depending on the silicate structures present in the sodium silicate solution.

国内外玻璃纤维用高岭土的质量差距及提高我国高岭土质量的对策%Differences of Kaolin Quality for Glass Fibers Made in China and Abroad and Improving Measures of Kaolin Quality Made in China

Institute of Scientific and Technical Information of China (English)

韩利雄; 姚远; 刘国斌

2011-01-01

Kaolins are one of important materials for E-glass fibers, which accounts for about 1/3 of blend mass. But the high-end market of kaolin for glass fibers was dominated by imports in China. Three kinds of kaolin samplespro-duced by ITC.Yichang and Yunnan for glass fibers were studied in this paper. The differences in chemical composition, phase,microstructure and granulometric composition were compared in detail by XRS,XRD,SEM and LPS. The research found that products of ITC had obvious advantages in product purity, particle size control and quality stability. In fact,the quality of domestic Kaolins is not bad,but because it is lack of specific quality standard and limited by the processing level of domestic non-metallic mineral, high-quality products cannot be obtained. In the future, kaolin industry should become bigger and stronger by integration as soon as possible, and try hard to improve the processing level of kaolin such as ore dressing,homogenization,etc,to fill the gap in the high-grade kaolin products for glass fibers.%高岭土是E-玻璃纤维的重要原料之一,其用量可占配合料的三分之一,但国内玻纤用高岭土高端市场一直被进口产品所占据.选取了美国ITC进口高岭土、宜昌硬质高岭土和云南水洗高岭土这三种有代表性的玻纤用高岭土,通过荧光光谱分析、X射线衍射分析、扫描电镜分析和激光粒度分析详细对比了它们在化学成分、物相组成、微观形貌和粒度分布四方面的差异.研究发现,美国玻纤用高岭土在产品纯度、粒度控制和质量稳定性方面有明显优势；国内玻纤用高岭土矿源品质并不差,只是由于缺乏专门的质量标准,同时受限于国内非金属矿产加工水平,而无法生产出高质量的产品.未来我国高岭土行业应尽快通过整合做大做强,努力提高高岭土选矿、均化等加工工艺水平,填补国内高档玻纤用高岭土产品空白.

Gravimetric and conductometric studies of the sedimentation kinetics in aqueous dispersions of kaoline

International Nuclear Information System (INIS)

Bulavyin, L.A.; Khrapatij, S.V.; Koval'chuk, V.Yi.; Klepko, V.V.; Lebovka, M.Yi.

2006-01-01

Using gravimetric and conductometric methods, the sedimentation kinetics in aqueous suspensions of Alekseev kaoline has been studied for pH value range from 4 to 10. It has been found that pH increasing leads to the decreasing of mean radii of flocks linearly. We found that sedimentation kinetics for intermediate pH values can be described by scaling equations that crossover time defined transition from a gravitational mechanism of deposition to the diffusion one

Fully Soft 3D-Printed Electroactive Fluidic Valve for Soft Hydraulic Robots.

Science.gov (United States)

Zatopa, Alex; Walker, Steph; Menguc, Yigit

2018-06-01

Soft robots are designed to utilize their compliance and contortionistic abilities to both interact safely with their environment and move through it in ways a rigid robot cannot. To more completely achieve this, the robot should be made of as many soft components as possible. Here we present a completely soft hydraulic control valve consisting of a 3D-printed photopolymer body with electrorheological (ER) fluid as a working fluid and gallium-indium-tin liquid metal alloy as electrodes. This soft 3D-printed ER valve weighs less than 10 g and allows for onboard actuation control, furthering the goal of an entirely soft controllable robot. The soft ER valve pressure-holding capabilities were tested under unstrained conditions, cyclic valve activation, and the strained conditions of bending, twisting, stretching, and indentation. It was found that the max holding pressure of the valve when 5 kV was applied across the electrodes was 264 kPa, and that the holding pressure deviated less than 15% from the unstrained max holding pressure under all strain conditions except for indentation, which had a 60% max pressure increase. In addition, a soft octopus-like robot was designed, 3D printed, and assembled, and a soft ER valve was used to stop the fluid flow, build pressure in the robot, and actuate six tentacle-like soft bending actuators.

Behaviour of major, minor and trace elements (including REEs during kaolinization processes at Zonouz deposit, northeast of Marand, East Azarbaidjan province

Directory of Open Access Journals (Sweden)

Vahideh Alipour

2011-11-01

Full Text Available The Zonouz kaolin deposit is located ~15 km northeast of Marand, East-Azarbaidjan province. Based on physical features in field investigations, such as color, five distinct kaolin types including (1 white, (2 lemon, (3 gray, (4 brown, and (5 yellow are distinguished in the deposit. Field evidence and petrographic studies indicate that the deposit is genetically close to trachy-andesite rocks. According to mineralogical data, the deposit contains quartz, kaolinite, montmorillonite, calcite, pyrophyllite, chlorite, muscovite-illite, dolomite, hematite, and anatase minerals. Geochemical data indicate that function of alteration processes on trachy-andesite rocks during development of Zonouz ore deposit was accompanied by leaching of elements such as Al, Na, K, Rb, Ba, V, Hf, Cu, Zr, Tm, Yb, and Lu, enrichment of elements such as U, Nb, and Ta, and leaching-fixation of elements such as Si, Fe, Ca, Mg, Ti, Mn, P, Cs, Sr, Th, Co, Cr, Ni, Y, Ga, LREE, Tb, Dy, Ho, and Er. Incorporation of obtained results from mineralogical and geochemical studies show that physico-chemical conditions of alteration environment, the relative stability of primary minerals, surface adsorption, preferential sorption by metallic oxides, existing of organic matters, scavenging and concentration processes, and fixation in neomorphic mineralogical phases played important role in distribution of elements in the deposit. Geochemical studies show that development of the deposit is relative to two types of processes, (1 hypogene and (2 supergene. The distribution pattern of REEs indicates that differentiation degree of LREEs from HREEs in supergene kaolins is more than hypogene kaolins. Geochemical studies indicate that minerals such as Mn-oxides, zircon, anatase, hematite, cerianite, and secondary phosphates (monazite, rhabdophane, churchite, and zenotime are the potential hosts for rare earth elements in this deposit.

Zeolite A synthesized from wastes of kaolin improvement process; Zeolita A sintetizada a partir de rejeitos do processo de beneficiamento de caulim

Energy Technology Data Exchange (ETDEWEB)

Santana, D.L.; Neves, R.F.; Silva, D.L., E-mail: danielaliraeq@yahoo.com.br, E-mail: dasilva@ufpa.br [Programa de Pos-Graduacao em Engenharia Quimica, Universidade Federal do Para - UFPA, Belem, PA (Brazil); Saraiva, A.C.F. [Centro de Tecnologia da Eletronorte, Belem, PA (Brazil)

2012-04-15

Raw materials were used to synthesize zeolite A as an alternative and more economical source of silica and aluminum, using waste from the kaolin of the paper industry. Zeolites are crystalline substances with a structure characterized by a framework of linked tetrahedra, each one consisting of four oxygen atoms surrounding a cation. The development of processes for the synthesis of zeolites is of great interest for use in the areas of purification, adsorption and catalysis. The starting materials for the synthesis of zeolite A consisted of wastes from kaolin beneficiation of paper companies of Para state, Brazil. The zeolite was obtained after calcination at 85 and 110 deg C during 24 h. The characterization of the starting material was performed by X-ray diffraction, chemical analysis, thermogravimetric and differential thermal analysis, and scanning electron microscopy. The characterization of zeolite A was done by X-ray diffraction and scanning electron microscopy. The kaolin waste used as starting material showed to be essentially kaolinite mineral. For the temperatures and time used in the synthesis it was possible to form the crystalline phase of zeolite A for the two starting materials. (author)

Gamma-induced radiation polymerization of kaolin composite for sorption of lanthanum, europium and uranium ions from low-grade monazite leachate

International Nuclear Information System (INIS)

Metwally, S.S.; Hassan, R.S.; El-Masry, E.H.; Borai, E.H.

2018-01-01

Gamma radiation polymerization method was used for the modification of kaolin to produce (poly acrylamide-acrylic acid)-Kaolin (PAM-AA-K). Monazite ore is one of the main resources of uranium and lanthanide elements, therefore, this work focused on sorption of uranium, lanthanum and europium ions from low grade monazite leachate. The removal percent for Eu 3+ , La 3+ and UO 2 2+ are 94.6, 91.6 and 73.4%, respectively. Monolayer capacity of Eu 3+ , La 3+ and UO 2 2+ were found to be 54.64, 45.87 and 37.59 mg/g, respectively. The sorption mechanism of lanthanum and europium ions on PAM-AA-K composite mainly takes place as Ln(OH) 2+ , and for uranium as uranyl ion, UO 2 2+ . (author)

Effect of Kaolin Clay and Alumina on Thermal Performance and Char Morphology of Intumescent fire retardant coating

Directory of Open Access Journals (Sweden)

aziz Hammad

2014-07-01

Full Text Available Intumescent fire retardant coating (IFRC have been developed by using ammonium polyphosphate, expandable graphite, melamine, boric acid, kaolin clay and alumina as fillers bound together with epoxy resin and cured with the help of curing agent. Five different formulations were developed with and without using fillers. Cured samples were burned in furnace at 500°C for 2h for char expansion. Bunsen burner test was performed for 1h using UL-94 vertical burning test to investigate the thermal performance of IFRC. The resultant char obtained after burning of coated samples were characterized by using field emission scanning electron microscopy for char morphology. Char composition was analyzed by using fourier transform infrared spectroscopy. Thermogravimetric analysis was carried out to investigate the residual weight of coating. Results showed that formulation with 0.5 weight % of kaolin clay and 0.5 weight % of alumina provide best thermal performance, uniform and multi-porous char structure with high anti-oxidation property.

Cytogenetic characteristics of soft wheat mutants under x-irradiation

International Nuclear Information System (INIS)

Shakaryan, Zh.O.; Avakyan, V.A.; Amirbekyan, V.A.

1981-01-01

Radiosensitivity of induced mutants of soft wheat is studied by criteria of frequency and character of changes in 1 and 2 divisions of meiosis. Two constant induced mutant forms of soft wheat were investigated. Mutant lines of squareheads with red ear (re) and erectoids 37/1 were obtained by X-ray irradiating hydride seeds F 1 of hybride combination of Alty-Agach Awnless 1. Seeds of mutants and initial kinds were exposed to X-rays at a dose of 10 kR. A conclusion may be drawn on the basis of studying the meiosis process in mutants and initial kinds of soft wheat on X-ray radiation that the mutants are more radiosensitive. This testifies to that that the induced mutants of soft wheat represent new genotypes in comparison with the initial kinds and differ from the latter not only in morphological characters but in the reaction norm with respect to external medium factors, i.e. the limit of possible changeability of the genotype has been extended [ru

Changes of surface electron states of InP under soft X-rays irradiation

International Nuclear Information System (INIS)

Yang Zhian; Yang Zushen; Jin Tao; Qui Rexi; Cui Mingqi; Liu Fengqin

1999-01-01

Changes of surface electronic states of InP under 1 keV X-ray irradiation is studied by X-ray photoelectron spectroscopy (XPS) and ultraviolet ray energy spectroscopy (UPS). The results show that the soft X-ray irradiation has little effect on In atoms but much on P atoms. The authors analysed the mechanism of irradiation and explained the major effect

Radiological impacts of the usability of Dolerite and Kaolin as raw materials for construction works in Abia State, Nigeria

International Nuclear Information System (INIS)

Enyinna, P.I.; Avwiri, G. O.

2011-01-01

This research study is aimed at carrying out radiometric analyses of the natural radioactivity resulting from the presence of radionuclides in dolerite and kaolin which are raw materials widely used in construction works. The activity concentrations of the identified natural radionuclides of 226 Ra, 228 Ra and 40 K in 40 samples of these solid minerals collected from 4 mining sites were determined by gamma ray spectroscopic technique using a well calibrated [NaI(Tl)] detector. The mean values of the activity concentrations of 226 Ra, 228 Ra and 40 K for the dolerite samples were found to be 10.989Bq/kg, 6.956Bq/kg, 723.253Bq/kg and 10.735Bq/kg, 6.175Bq/kg, 714.895Bq/kg respectively (for the 2 dolerite mining sites); and for the kaolin samples, 8.507Bq/kg, 7.33Bq/kg, 87.511Bq/kg and 8.416Bq/kg, 7.354Bq/kg, 86.727Bq/kg respectively (for the 2 kaolin mining sites). The radium equivalent activity, the absorbed dose rate, the equivalent dose rate, the external and internal hazard indices, the annual outdoor and indoor effective dose rates were computed and compared with international radiological standards to ascertain if these minerals pose any radiological hazard. The results obtained were found to conform within the limits of acceptable international radiological standards and may not pose any immediate threat to the public and users of these two solid minerals for construction works.

Synthesis of 4A zeolites from kaolin for obtaining 5A zeolites through ionic exchange for adsorption of arsenic

International Nuclear Information System (INIS)

Resmini Melo, Carolina; Gracher Riella, Humberto; Cabral Kuhnen, Nivaldo; Angioletto, Elidio; Melo, Aline Resmini; Bernardin, Adriano Michael; Rocha, Marcio Roberto da; Silva, Luciano da

2012-01-01

Highlights: ► We synthesize 4A zeolite from kaolin by hydrothermal reaction with sodium hydroxide. ► The 4A zeolite synthesized underwent ion exchange with calcium ions, with different parameters, to obtain 5A zeolites. ► The best 4A zeolite obtained was used as adsorbent material for arsenic ions. ► The results showed that the 5A zeolite material obtained is a good adsorber of heavy ions. - Abstract: The synthesis of adsorbing zeolite materials requires fine control of the processing variables. There are distinct process variable settings for obtaining specific desired types of zeolites. The intent of this study was to obtain 4A zeolites from kaolin in order to obtain 5A zeolites through ionic exchange with the previously synthesized zeolite. This zeolite 5A was used as an adsorbent for arsenic ions. The results obtained were satisfactory.

Contrasting respirable quartz and kaolin retention of lecithin surfactant and expression of membranolytic activity following phospholipase A2 digestion.

Science.gov (United States)

Wallace, W E; Keane, M J; Mike, P S; Hill, C A; Vallyathan, V; Regad, E D

1992-11-01

Respirable-sized quartz, a well-established fibrogenic mineral dust, is compared with kaolin in erythrocyte hemolysis assays after treatment with saline dispersion of dipalmitoyl phosphatidylcholine, a primary phospholipid component of pulmonary surfactant. Both dusts are rendered inactive after treatment, but the membranolytic activity is partly to fully restored after treatment with phospholipase A2, an enzyme normally associated with cellular plasma membranes and lysosomes. Phospholipid-coated dusts were incubated for periods of 2-72 h at a series of applied enzyme concentrations, and the adsorbed lipid species and hemolytic activity were quantitated at each time for both dusts. Surfactant was lost more readily from quartz than from kaolin, with consequent more rapid restoration of mineral surface hemolytic activity for quartz. Interactions of surfactant and mineral surface functional groups responsible for the mineral-specific rate differences, and implications for determining the mineral surface bioavailability of silica and silicate dusts, are discussed.

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production; Estudo da viabilidade da incorporacao do residuo fino do caulim na concepcao de formulacoes de porcelanatos

Energy Technology Data Exchange (ETDEWEB)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de, E-mail: vanessaalmeida90@gmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2016-07-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Potential of kaolin-based particle film barriers for Formosan subterranean termite (Isoptera: Rhinotermitidae) control

Science.gov (United States)

Wiltz, B.A.; Woodson, W.D.; Puterka, G.J.

2010-01-01

Effects of three particle film products on Formosan subterranean termites, Coptotermes formosanus Shiraki, were evaluated in feeding, tunneling, and contact assays. The particle films, hydrophobic M96-018 and hydrophilic Surround and Surround WP are based on the inert clay mineral kaolin. In 2-week long no-choice feeding tests, significant mortality occurred only with M96-018-coated wood. When a choice was provided, M96-018 and Surround were consumed at higher rates than untreated wood. Surround WP did not differ from controls in either test. In the tunneling assay termites were given the option of crossing a kaolin-sand mixture to reach an alternate food source. After 3-weeks, rates of 1% and 5% M96-018 provided an effective barrier to Formosan termite tunneling, while termites were not stopped by rates as high as 20% Surround and Surround WP. Dust treatments of all three formulations caused significant increases in mortality within 24 h, with mortality rates ranging from 72.0 - 97.3% within 72 h of treatment. The particle films were most effective when moisture levels were low, suggesting that desiccation was the mechanism for mortality. All particle films showed potential for use in above ground applications while hydrophobic M06-018 has the most potential as a soil barrier to subterranean termites.

Heavy Metal Diffusion through Soft Clay under High Hydraulic Gradients

Directory of Open Access Journals (Sweden)

Zaheer Ahmed Almani

2013-04-01

Full Text Available This study was focused on the determination of contaminant transport parameters of heavy metal Zinc moving through saturated soft Bangkok undisturbed clay under high hydraulic gradients. These parameters were compared with contaminant transport determined under concentration gradient alone (pure diffusion. In total fifteen column tests were conducted and a mathematical model was applied to determine the coefficients. Two different source concentrations conditions, constant and decreasing, were applied. Testing periods were ranged from 15-60 days while hydraulic gradients were ranged from 0-500. The curves between relative concentration and time and pore volume were developed for the constant source condition whereas curves between source reservoirs concentrations and time were developed for decreasing source condition. The effective diffusion and distribution coefficients, De and Kd, were determined by curve fitting using the computer code POLLUTE v 6.3. The results showed that diffusion coefficient increases and distribution coefficient decreases as hydraulic gradient increases from 0 to high value of 500 due to contribution of dispersion and additional molecular diffusion at high advective velocity. Thus, testing at high gradients ensures the safe performance of earthen barriers under worse conditions.

Waste characterization emanated from kaolin submitted the improvement to process hydrocycloning

International Nuclear Information System (INIS)

Barbosa Neto, M.C.; Nunes, A.S.; Caetano, A.L.A.; Marques, V.C.; Macedo, D.A.; Ferreira, H.S.; Dutra, R.P.S.

2016-01-01

The hydrocyclones are equipment commonly used for separation of particles by size. The resulting material of this process usually presents different characteristics of the material, which was not subjected to treatment. Therefore, a study of the waste characteristics derived from kaolin processing submitted to hydrocycloning process compared to the same residue without going through the process was executed. The different samples were characterized by X-ray diffraction, X-ray fluorescence, particle size analysis and thermal analysis. The results indicate that the hydrocycloning not modify the mineralogical structure nor chemical material. The particle size analysis identified that the fine fraction, resulting from the process, presented particle size lower than the reference material. (author)

Fundamentals of soft robot locomotion.

Science.gov (United States)

Calisti, M; Picardi, G; Laschi, C

2017-05-01

Soft robotics and its related technologies enable robot abilities in several robotics domains including, but not exclusively related to, manipulation, manufacturing, human-robot interaction and locomotion. Although field applications have emerged for soft manipulation and human-robot interaction, mobile soft robots appear to remain in the research stage, involving the somehow conflictual goals of having a deformable body and exerting forces on the environment to achieve locomotion. This paper aims to provide a reference guide for researchers approaching mobile soft robotics, to describe the underlying principles of soft robot locomotion with its pros and cons, and to envisage applications and further developments for mobile soft robotics. © 2017 The Author(s).

Synthesis of Al4SiC4 powders from kaolin grog, aluminum and carbon black by carbothermal reaction

Science.gov (United States)

Yuan, Wenjie; Yu, Chao; Deng, Chengji; Zhu, Hongxi

2013-12-01

In this paper, the synthesis of Al4SiC4 used as natural oxide materials by carbothermal reduction was investigated in order to explore the synthesis route with low costs. The samples were calcined by using kaolin grog, aluminum and carbon black as raw materials with the selected proportion at the temperature from 1500 to 1800 ° C for 2 hours under flow argon atmosphere. The phase composition of reaction products were determined by X-ray diffraction. The microstructure and elemental composition of different phases were observed and identified by scanning electron microscopy and energy dispersive spectroscopy. The mechanism of reaction processing was discussed. The results show that Al4SiC4 powders composed of hexagonal plate-like particulates with various sizes and the thickness of less than 20 μm are obtained when the temperature reaches 1800 °C.

Synthesis of Al4SiC4 powders from kaolin grog, aluminum and carbon black by carbothermal reaction

International Nuclear Information System (INIS)

Yuan, Wenjie; Yu, Chao; Deng, Chengji; Zhu, Hongxi

2013-01-01

In this paper, the synthesis of Al 4 SiC 4 used as natural oxide materials by carbothermal reduction was investigated in order to explore the synthesis route with low costs. The samples were calcined by using kaolin grog, aluminum and carbon black as raw materials with the selected proportion at the temperature from 1500 to 1800 ° C for 2 hours under flow argon atmosphere. The phase composition of reaction products were determined by X-ray diffraction. The microstructure and elemental composition of different phases were observed and identified by scanning electron microscopy and energy dispersive spectroscopy. The mechanism of reaction processing was discussed. The results show that Al 4 SiC 4 powders composed of hexagonal plate-like particulates with various sizes and the thickness of less than 20 μm are obtained when the temperature reaches 1800 °C

Characterization of ceramic masses using raw material of Para, Brazil: kaolin in natura; Caracterizaco de massas ceramicas utilizando materia--prima do Para: caulim in natura

Energy Technology Data Exchange (ETDEWEB)

Vida, T.A.; Facury Neto, E.; Rabelo, A.A. [Universidade Federal do Para (UFPA), Maraba, PA (Brazil). Fac. de Engenharia de Materiais

2009-07-01

The incorporation rejects to the mixtures has if shown viable in the reduction of the environmental liability and for the obtaining of a better quality of the ceramic mass. In the present work, is tried to study the potentiality of the use of ceramic formulations with the addition of kaolin in natura to the clays. Formulations with two clays of the area of the municipal district of Maraba with addition of up to 60% in kaolin weight were prepared and characterized. For the determination of the physical and mechanical properties proof bodies were made by prensagem uniaxial and later burned in temperature from 900 to 1200 deg C with landing of 3 hours. The raw materials were characterized through diffraction of rays X (DRX) and thermogravimetric analysis. The proof bodies prepared were used for determination of the lineal retraction (RL), absorption of water, apparent porosity, apparent density, loss to the fire and rupture module the flexing. The results were satisfactory for the smallest kaolin tenors in the ceramic mass, and the mass with 20% presented rupture module elevated, in the temperature of 1200 deg C. (author)

Location-Dependent Query Processing Under Soft Real-Time Constraints

Directory of Open Access Journals (Sweden)

Zoubir Mammeri

2009-01-01

Full Text Available In recent years, mobile devices and applications achieved an increasing development. In database field, this development required methods to consider new query types like location-dependent queries (i.e. the query results depend on the query issuer location. Although several researches addressed problems related to location-dependent query processing, a few works considered timing requirements that may be associated with queries (i.e., the query results must be delivered to mobile clients on time. The main objective of this paper is to propose a solution for location-dependent query processing under soft real-time constraints. Hence, we propose methods to take into account client location-dependency and to maximize the percentage of queries respecting their deadlines. We validate our proposal by implementing a prototype based on Oracle DBMS. Performance evaluation results show that the proposed solution optimizes the percentage of queries meeting their deadlines and the communication cost.

Facile Fabrication of a PDMS@Stearic Acid-Kaolin Coating on Lignocellulose Composites with Superhydrophobicity and Flame Retardancy

Directory of Open Access Journals (Sweden)

Zhe Wang

2018-05-01

Full Text Available The disadvantages such as swelling after absorbing water and flammability restrict the widespread applications of lignocellulose composites (LC. Herein, a facile and effective method to fabricate superhydrophobic surfaces with flame retardancy on LC has been investigated by coating polydimethylsiloxane (PDMS and stearic acid (STA modified kaolin (KL particles. The as-prepared coatings on the LC exhibited a good repellency to water (a contact angle = 156°. Owing to the excellent flame retardancy of kaolin particles, the LC coated with PDMS@STA-KL displayed a good flame retardancy during limiting oxygen index and cone calorimeter tests. After the coating treatment, the limiting oxygen index value of the LC increased to 41.0. Cone calorimetry results indicated that the ignition time of the LC coated with PDMS@STA-KL increased by 40 s compared with that of uncoated LC. Moreover, the peak heat release rate (PHRR and the total heat release (THR of LC coated with PDMS@STA-KL reduced by 18.7% and 19.2% compared with those of uncoated LC, respectively. This LC coating with improved water repellency and flame retardancy can be considered as a potential alternative to protect the lignocellulose composite.

Attenuation measurements of ultrasound in a kaolin-water slurry. A linear dependence upon frequency

International Nuclear Information System (INIS)

Greenwood, M.S.; Mai, J.L.; Good, M.S.

1993-01-01

The attenuation of ultrasound through a kaolin-water slurry was measured for frequencies ranging from 0.5 to 3.0 MHz. The maximum concentration of the slurry was for a weight percentage of 44% (or a volume fraction of 0.24). The goal of these measurements was to assess the feasibility of using ultrasonic attenuation to determine the concentration of a slurry of known composition. The measurements were obtained by consecutively adding kaolin to the slurry and measuring the attenuation at each concentration. After reaching a maximum concentration a dilution technique was used, in which an amount of slurry was removed and water was added, to obtain the attenuation as a function of the concentration. The dilution technique was the more effective method to obtain calibration data. These measurements were carried out using two transducers, having a center frequency of 2.25 MHz, separated by 0.1016m (4.0 in.). The maximum attenuation measured in these experiments was about 100Np/m, but the experimental apparatus has the capability of measuring a larger attenuation if the distance between the two transducers is decreased. For a given frequency, the data show that ln V/V 0 depends linearly upon the volume fraction (V is the received voltage for the slurry and V 0 is that obtained for water). This indicated that each particle acts independently in attenuating ultrasound. 12 refs., 7 figs., 3 tabs

High-temperature CO2 capture cycles of hydrated limestone prepared with aluminum (hydr)oxides derived from kaolin

International Nuclear Information System (INIS)

Wang, Ke; Zhao, Pengfei; Guo, Xin; Han, Dongtai; Chao, Yang

2014-01-01

Highlights: • Hydrated limestone exhibited a higher reactivity and stability. • Microstructure of hydrated limestone was significantly improved. • Hydrated limestone still suffered less loss-incapacity. • Hydrated limestone sorbents with kaolin-based binders were prepared and characterized. • Sorbents prepared from hydrated limestone and Al(OH) 3 binder are a promising sorbent. - Abstract: A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO 2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO 2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO 2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca 12 Al 14 O 33 particles hindered densification and sintering of the CaO phase

Mineralogical characterization and beneficiation study of kaolin from Equador (RN) and Junco do Serido (PB) to increase the brightness index

International Nuclear Information System (INIS)

Campos, V.M.J.S.; Bertolino, L.C.; Alves, O.C.

2017-01-01

Kaolin is a rock composed mainly of kaolinite. It is used in many industrial segments, such as paper and ceramics. However, for these uses it is necessary to submit the ore to appropriate beneficiation, which generally involves magnetic separation and chemical bleaching, aiming to remove iron oxide and hydroxide, raising brightness index. This work reports the mineralogical characterization and analysis of the beneficiation of three samples of kaolin, two from Equador (Rio Grande do Norte - RN) and the third from Junco do Serido (Paraiba - PB). The samples were submitted to granulometric classification in sieve of 44 μm, magnetic separation in a magnetic induction of 14000 gauss, and chemical bleaching with sodium dithionite during 240 min. The processes were divided into two beneficiation routes. X-ray diffraction, chemical analysis by X-ray fluorescence and scanning electron microscopy were used for mineralogical characterization of the ore and measurement of the brightness index, while electron paramagnetic resonance was applied to study the variation of iron oxides and hydroxides during beneficiation. The results indicate that just 30 min of chemical bleaching without magnetic separation was sufficient to increase the brightness index from 78.2 to 90.2% and from 91.3 to 95.7% in the two samples from Equador (RN) and from 86.9 to 90.4% in the sample from Junco do Serido (PB). The magnetic separation, although causing a small increase in the brightness index, was inefficient for removal of iron oxides and hydroxides. The results indicated no need for using magnetic separation in plants for beneficiation of kaolin from these two locations, providing the reduction of production costs allowing better exploitation of the ore. (author)

For production of ceramic plates coating using waste kaolin, granite and marble

International Nuclear Information System (INIS)

Sales, J.L.; Morais, C.R.S.; Lima, L.M.R.; Altidis, M.E.D.

2011-01-01

The objective is to benefit and characterize waste from kaolin, marble and granite studying their thermal properties and spectroscopic in employment perspective on ceramic production of flooring boards. The residues were benefited through the process of dry grinding mill in greyhounds and passed through sieve 0.074 mm (ABNT No. 200), observing their suitability for the formulation of ceramic pastes. Tests were performed physicochemical characterization (particle size analysis, X-ray fluorescence and X-ray diffraction) and thermal (differential thermal analysis and thermogravimetry). The results showed that these residues showed satisfactory properties for the purpose for which it proposes, and contribute to reducing environmental impacts, allowing the reuse of the production of ceramic plates (author)

Mineralogical and chemical characterization of DD3 kaolin from the east of Algeria

Energy Technology Data Exchange (ETDEWEB)

Senoussi, H.; Osmani, H.; Courtois, C.; Bourahli, M. H.

2016-08-01

The mineralogical and chemical characteristics, based on X-ray diffraction (XRD) and scanning electron microscopy, of a kaolin known as DD3, from eastern Algeria were examined in the present study. The results showed that kaolin DD3 has an alumina content of 39%. The SiO{sub 2}/Al{sub 2}O{sub 3} molar ratio of 2.14 is close to that of a pure halloysite. The hematite concentration is relatively large and the flux oxides ratios remain as acceptable impurities. Microscopic observations showed a predominant tubular halloysite phase, flattened hexagonal platelets corresponding to the presence of kaolinite and its polymorphs (nacrite, dickite), and hydrated alumina. The SiO{sub 2}/Al{sub 2}O{sub 3} molar ratio and tubular DD3 suggest possible uses in technical ceramics and nano technology applications. Analysis by XRD revealed the presence of many phases. Thermal treatment at 450 degree centigrade and chemical treatment with HCl confirmed the presence of halloysite. The inclusion in the clay of organic molecules (dimethylsulfoxide (DMSO), DMF, and diluted glycerol) showed that the DMSO led to expansion of the inter-planar distance. The intercalation by DMSO molecules resulted in a shift of the basal peak from 10 to 11.02 A and partial displacement of the peak from 3.35 to 3.65 A. These two peaks are characteristic of halloysite. The presence of residual nacrite was also confirmed by the shift of the peak observed at 3.35 A. A full analysis of the XRD patterns using the Match software, based on these results, showed that the DD3 clay consists of >60% halloysite. (Author)

Mineralogical and chemical characterization of DD3 kaolin from the east of Algeria

International Nuclear Information System (INIS)

Senoussi, H.; Osmani, H.; Courtois, C.; Bourahli, M. H.

2016-01-01

The mineralogical and chemical characteristics, based on X-ray diffraction (XRD) and scanning electron microscopy, of a kaolin known as DD3, from eastern Algeria were examined in the present study. The results showed that kaolin DD3 has an alumina content of 39%. The SiO 2 /Al 2 O 3 molar ratio of 2.14 is close to that of a pure halloysite. The hematite concentration is relatively large and the flux oxides ratios remain as acceptable impurities. Microscopic observations showed a predominant tubular halloysite phase, flattened hexagonal platelets corresponding to the presence of kaolinite and its polymorphs (nacrite, dickite), and hydrated alumina. The SiO 2 /Al 2 O 3 molar ratio and tubular DD3 suggest possible uses in technical ceramics and nano technology applications. Analysis by XRD revealed the presence of many phases. Thermal treatment at 450 degree centigrade and chemical treatment with HCl confirmed the presence of halloysite. The inclusion in the clay of organic molecules (dimethylsulfoxide (DMSO), DMF, and diluted glycerol) showed that the DMSO led to expansion of the inter-planar distance. The intercalation by DMSO molecules resulted in a shift of the basal peak from 10 to 11.02 A and partial displacement of the peak from 3.35 to 3.65 A. These two peaks are characteristic of halloysite. The presence of residual nacrite was also confirmed by the shift of the peak observed at 3.35 A. A full analysis of the XRD patterns using the Match software, based on these results, showed that the DD3 clay consists of >60% halloysite. (Author)

Comparative numerical study of kaolin clay with three drying methods: Convective, convective–microwave and convective infrared modes

International Nuclear Information System (INIS)

Hammouda, I.; Mihoubi, D.

2014-01-01

Highlights: • Modelling of drying of deformable media. • Theoretical study of kaolin clay with three drying methods: convective, convective–microwave and convective infrared mode. • The stresses generated during convective, microwave/convective drying and infrared/convective drying. • The combined drying decrease the intensity of stresses developed during drying. - Abstract: A mathematical model is developed to simulate the response of a kaolin clay sample when subjected to convective, convective–microwave and convective–infrared mode. This model is proposed to describe heat, mass, and momentum transfers applied to a viscoelastic medium described by a Maxwell model with two branches. The combined drying methods were investigated to examine whether these types of drying may minimize cracking that can be generated in the product and to know whether the best enhancement is developed by the use of infra-red or microwave radiation. The numerical code allowed us to determine, and thus, compare the effect of the drying mode on drying rate, temperature, moisture content and mechanical stress evolutions during drying. The numerical results show that the combined drying decrease the intensity of stresses developed during drying and that convective–microwave drying is the best method that gives a good quality of dried product

Soft Regulation with Crowd Recommendation: Coordinating Self-Interested Agents in Sociotechnical Systems under Imperfect Information.

Science.gov (United States)

Luo, Yu; Iyengar, Garud; Venkatasubramanian, Venkat

2016-01-01

Regulating emerging industries is challenging, even controversial at times. Under-regulation can result in safety threats to plant personnel, surrounding communities, and the environment. Over-regulation may hinder innovation, progress, and economic growth. Since one typically has limited understanding of, and experience with, the novel technology in practice, it is difficult to accomplish a properly balanced regulation. In this work, we propose a control and coordination policy called soft regulation that attempts to strike the right balance and create a collective learning environment. In soft regulation mechanism, individual agents can accept, reject, or partially accept the regulator's recommendation. This non-intrusive coordination does not interrupt normal operations. The extent to which an agent accepts the recommendation is mediated by a confidence level (from 0 to 100%). Among all possible recommendation methods, we investigate two in particular: the best recommendation wherein the regulator is completely informed and the crowd recommendation wherein the regulator collects the crowd's average and recommends that value. We show by analysis and simulations that soft regulation with crowd recommendation performs well. It converges to optimum, and is as good as the best recommendation for a wide range of confidence levels. This work sheds a new theoretical perspective on the concept of the wisdom of crowds.

Soft Regulation with Crowd Recommendation: Coordinating Self-Interested Agents in Sociotechnical Systems under Imperfect Information

Science.gov (United States)

2016-01-01

Regulating emerging industries is challenging, even controversial at times. Under-regulation can result in safety threats to plant personnel, surrounding communities, and the environment. Over-regulation may hinder innovation, progress, and economic growth. Since one typically has limited understanding of, and experience with, the novel technology in practice, it is difficult to accomplish a properly balanced regulation. In this work, we propose a control and coordination policy called soft regulation that attempts to strike the right balance and create a collective learning environment. In soft regulation mechanism, individual agents can accept, reject, or partially accept the regulator’s recommendation. This non-intrusive coordination does not interrupt normal operations. The extent to which an agent accepts the recommendation is mediated by a confidence level (from 0 to 100%). Among all possible recommendation methods, we investigate two in particular: the best recommendation wherein the regulator is completely informed and the crowd recommendation wherein the regulator collects the crowd’s average and recommends that value. We show by analysis and simulations that soft regulation with crowd recommendation performs well. It converges to optimum, and is as good as the best recommendation for a wide range of confidence levels. This work sheds a new theoretical perspective on the concept of the wisdom of crowds. PMID:26977699

Bipolar soft connected, bipolar soft disconnected and bipolar soft compact spaces

Directory of Open Access Journals (Sweden)

Muhammad Shabir

2017-06-01

Full Text Available Bipolar soft topological spaces are mathematical expressions to estimate interpretation of data frameworks. Bipolar soft theory considers the core features of data granules. Bipolarity is important to distinguish between positive information which is guaranteed to be possible and negative information which is forbidden or surely false. Connectedness and compactness are the most important fundamental topological properties. These properties highlight the main features of topological spaces and distinguish one topology from another. Taking this into account, we explore the bipolar soft connectedness, bipolar soft disconnectedness and bipolar soft compactness properties for bipolar soft topological spaces. Moreover, we introduce the notion of bipolar soft disjoint sets, bipolar soft separation, and bipolar soft hereditary property and study on bipolar soft connected and disconnected spaces. By giving the detailed picture of bipolar soft connected and disconnected spaces we investigate bipolar soft compact spaces and derive some results related to this concept.

The efficacy of kaolin clay in reducing the duration and severity of `heat' diarrhea in foals

OpenAIRE

PIESZKA, MAGDALENA; LUSZCZYNSKI, JAROSLAW; HEDRZAK, MAGDALENA; GONCHAROVA, KATERINA; PIERZYNOWSKI, STEFAN G.

2016-01-01

'Heat' diarrhea in foals is an onerous but not life-threatening ailment, which indicates that it may be of osmotic origin. This was confirmed by a successful attempt, presented in this paper, to alleviate the severity and duration of foal heat diarrhea with the use of a typical absorbent, kaolin clay, as a feed additive, usually applied in feed production as an anticaking agent. Based on the present results, it can be concluded that treatment of foals maintained on different stud fa...

Dissecting soft radiation with factorization

International Nuclear Information System (INIS)

Stewart, Iain W.; Tackmann, Frank J.; Waalewijn, Wouter J.; Amsterdam Univ.

2014-05-01

An essential part of high-energy hadronic collisions is the soft hadronic activity that underlies the primary hard interaction. It can receive contributions from soft radiation from the primary hard partons, secondary multiple parton interactions (MPI), and factorization violating effects. The invariant mass spectrum of the leading jet in Z+jet and H+jet events is directly sensitive to these effects. We use a QCD factorization theorem to predict the dependence on the jet radius R, jet p T , jet rapidity, and partonic process for both the perturbative and nonperturbative components of primary soft radiation. The nonperturbative contributions involve only odd powers of R, and the linear R term is universal for quark and gluon jets. The hadronization model in PYTHIA8 agrees well with these properties. The perturbative soft initial state radiation (ISR) has a contribution that depends on the jet area in the same way as the underlying event. This degeneracy is broken by the jet p T dependence. The size of this soft ISR contribution is proportional to the color state of the initial partons, yielding the same positive contribution for gg→Hg and gq→Zq, but a negative interference contribution for q anti q→Zg. Hence, measuring these dependencies allows one to separate hadronization, soft ISR, and MPI contributions in the data.

Soft Sensor for Oxide Scales on the Steam Side of Superheater Tubes under Uneven Circumferential Load

Directory of Open Access Journals (Sweden)

Qing Wei Li

2015-01-01

Full Text Available A soft sensor for oxide scales on the steam side of superheater tubes of utility boiler under uneven circumferential loading is proposed for the first time. First finite volume method is employed to simulate oxide scales growth temperature on the steam side of superheater tube. Then appropriate time and spatial intervals are selected to calculate oxide scales thickness along the circumferential direction. On the basis of the oxide scale thickness, the stress of oxide scales is calculated by the finite element method. At last, the oxide scale thickness and stress sensors are established on support vector machine (SMV optimized by particle swarm optimization (PSO with time and circumferential angles as inputs and oxide scale thickness and stress as outputs. Temperature and stress calculation methods are validated by the operation data and experimental data, respectively. The soft sensor is applied to the superheater tubes of some power plant. Results show that the soft sensor can give enough accurate results for oxide scale thickness and stress in reasonable time. The forecasting model provides a convenient way for the research of the oxide scale failure.

CAT & MAUS: A novel system for true dynamic motion measurement of underlying bony structures with compensation for soft tissue movement.

Science.gov (United States)

Jia, Rui; Monk, Paul; Murray, David; Noble, J Alison; Mellon, Stephen

2017-09-06

Optoelectronic motion capture systems are widely employed to measure the movement of human joints. However, there can be a significant discrepancy between the data obtained by a motion capture system (MCS) and the actual movement of underlying bony structures, which is attributed to soft tissue artefact. In this paper, a computer-aided tracking and motion analysis with ultrasound (CAT & MAUS) system with an augmented globally optimal registration algorithm is presented to dynamically track the underlying bony structure during movement. The augmented registration part of CAT & MAUS was validated with a high system accuracy of 80%. The Euclidean distance between the marker-based bony landmark and the bony landmark tracked by CAT & MAUS was calculated to quantify the measurement error of an MCS caused by soft tissue artefact during movement. The average Euclidean distance between the target bony landmark measured by each of the CAT & MAUS system and the MCS alone varied from 8.32mm to 16.87mm in gait. This indicates the discrepancy between the MCS measured bony landmark and the actual underlying bony landmark. Moreover, Procrustes analysis was applied to demonstrate that CAT & MAUS reduces the deformation of the body segment shape modeled by markers during motion. The augmented CAT & MAUS system shows its potential to dynamically detect and locate actual underlying bony landmarks, which reduces the MCS measurement error caused by soft tissue artefact during movement. Copyright © 2017 Elsevier Ltd. All rights reserved.

Percutaneous interventional forceps removal of radiopaque foreign bodies in soft-tissue under fluoroscopic guidance

International Nuclear Information System (INIS)

Yang Xiujun; Xing Guangfu; Shi Changwen; Li Wei

2011-01-01

Objective: To evaluate the clinical value and limitations of percutaneous interventional forceps retrieval technique under fluoroscopic guidance in removing radiopaque foreign bodies in soft-tissue. Methods: A total of 4 105 consecutive soft-tissue injury patients with radiopaque foreign bodies, encountered in authors' hospital during the period from June 2005 to June 2010, were involved in this study. The diagnosis was confirmed by plain X-ray films in all patients. Additional CT scanning was performed in 1 591 patients, in some of them 3D reconstruction was adopted. With local anesthesia percutaneous interventional forceps retrieval of radiopaque foreign bodies (PIRFB) was carried out under C-arm video-fluoroscopic guidance. Results: Of all patients in this study, 61.34% (2 518/4 105) was treated by PIRFB (study group), and 38.66% (1 587/4 105) was not treated with PIRFB (control group). In study group,the complete and partial curative rate was 95.07% (2 394/2 518) and 4.81% (121/2 518) respectively, and the failure rate was 0.12% (3/2 518). Of 1 587 patients in control group, 25.02% (n=397) left hospital by patient's own reasons and 74.98% (n=1190) was discharged from hospital due to medical or technical reasons. In control group,the foreign objects were close to big vessels in 65.22% (1 035/1 587), large local hematoma was accompanied in 2.90% (46/1 587), associated traumatic pseudoaneurysm was seen in 1.32% (21/1 587) and the foreign objects were glass pieces and the like were found in 5.55% (88/1 587). No serious postoperative complications that required specific therapy, such as bleeding, infection and nerve damage, etc. occurred. CT, especially enhanced CT three-dimensional images, could precisely display the vasculatures nearby the foreign body, which helped make the correct judgment of the removal ability and the operation risk for foreign bodies with interventional procedure. Conclusion: Percutaneous interventional forceps retrieval technique under

Erosion behavior of soft, amorphous deuterated carbon films by heat treatment in air and under vacuum

International Nuclear Information System (INIS)

Maruyama, K.

1999-01-01

The erosion of soft a-C:D films by heat treatment in air and under vacuum is studied by ion-beam analysis. When the films are heated in air above 500 K, the film thickness and the areal densities of C and especially D decrease, and oxygen is incorporated in the films. The initial atomic loss rates of carbon and deuterium from the films are 2.6 x 10 17 C atoms cm -2 h -1 and 4.8 x 10 17 D atoms cm -2 h -1 at 550 K. However, after D depletion the films show a resistivity against further erosion due to annealing in air. When the films are heated under vacuum erosion starts at about 600 K and all components including D decrease proportionally to the film thickness. Thermal desorption spectroscopy of the films reveals the evolution of C x D y type hydrocarbons. Infrared analysis shows that the incorporated oxygen is chemically bonded to carbon. The thermally-activated decomposition of the soft a-C:D films is compared to that of hard a-C:D films and a reaction scheme is suggested. (orig.)

Mineralogical characterization and beneficiation study of kaolin from Equador (RN and Junco do Seridó (PB to increase the brightness index

Directory of Open Access Journals (Sweden)

V. M. J. S. Campos

Full Text Available Abstract Kaolin is a rock composed mainly of kaolinite. It is used in many industrial segments, such as paper and ceramics. However, for these uses it is necessary to submit the ore to appropriate beneficiation, which generally involves magnetic separation and chemical bleaching, aiming to remove iron oxide and hydroxide, raising brightness index. This work reports the mineralogical characterization and analysis of the beneficiation of three samples of kaolin, two from Equador (Rio Grande do Norte - RN and the third from Junco do Seridó (Paraíba - PB. The samples were submitted to granulometric classification in sieve of 44 μm, magnetic separation in a magnetic induction of 14000 gauss, and chemical bleaching with sodium dithionite during 240 min. The processes were divided into two beneficiation routes. X-ray diffraction, chemical analysis by X-ray fluorescence and scanning electron microscopy were used for mineralogical characterization of the ore and measurement of the brightness index, while electron paramagnetic resonance was applied to study the variation of iron oxides and hydroxides during beneficiation. The results indicate that just 30 min of chemical bleaching without magnetic separation was sufficient to increase the brightness index from 78.2 to 90.2% and from 91.3 to 95.7% in the two samples from Equador (RN and from 86.9 to 90.4% in the sample from Junco do Seridó (PB. The magnetic separation, although causing a small increase in the brightness index, was inefficient for removal of iron oxides and hydroxides. The results indicated no need for using magnetic separation in plants for beneficiation of kaolin from these two locations, providing the reduction of production costs allowing better exploitation of the ore.

Determination of iron and titanium in kaolins by the method of non-dispersive X-ray fluorescence

International Nuclear Information System (INIS)

Bialy, N.; Kierzek, J.; Parus, J.

1976-01-01

The possibility of application of the radioactive source excited X-ray fluorescence analysis for titanium and iron determination in kaolins to the routine test of the refinement process has been studied. The iron content can be determined with a simple counting system using a single-channel pulse height analyser, argon filled proportional counter and 109 Cd source of 3 mCi for the excitation of K Fe rays. The samples were analyzed both as pellets and powders. The iron content ranged from 0.2-2.5% and titanium from 0.1-0.64%. The best values of precision and determination limit have been achieved for iron with 238 Pu and for titanium with 55 Fe. The precision and accuracy of the X-ray fluorescence method of iron and titanium determination in kaolins are comparable to those of the chemical method. For the simultaneous iron and titanium determination in the discussed region of concentration it is the most advantageous to use the plutonium source with the activity of several tens of mCi and Si(Li) detector with a moderate resolution (250-300 eV for 5.9 keV). The time of the analysis carried out by the described method is several times shorter than the chemical method. The apparatus used in this method is relatively simple, the sample preparation does not require any chemical treatment and the cost of labour of the sample preparation is minimal. (T.G.)

Role of Brittle Behaviour of Soft Calcarenites Under Low Confinement: Laboratory Observations and Numerical Investigation

Science.gov (United States)

Lollino, Piernicola; Andriani, Gioacchino Francesco

2017-07-01

The strength decay that occurs in the post-peak stage, under low confinement stress, represents a key factor of the stress-strain behaviour of rocks. However, for soft rocks this issue is generally underestimated or even neglected in the solution of boundary value problems, as for example those concerning the stability of underground cavities or rocky cliffs. In these cases, the constitutive models frequently used in limit equilibrium analyses or more sophisticated numerical calculations are, respectively, rigid-plastic or elastic-perfectly plastic. In particular, most of commercial continuum-based numerical codes propose a variety of constitutive models, including elasticity, elasto-plasticity, strain-softening and elasto-viscoplasticity, which are not exhaustive in simulating the progressive failure mechanisms affecting brittle rock materials, these being characterized by material detachment and crack opening and propagation. As a consequence, a numerical coupling with mechanical joint propagation is needed to cope with fracture mechanics. Therefore, continuum-based applications that treat the simulation of the failure processes of intact rock masses at low stress levels may need the adoption of numerical techniques capable of implementing fracture mechanics and rock brittleness concepts, as it is shown in this paper. This work is aimed at highlighting, for some applications of rock mechanics, the essential role of post-peak brittleness of soft rocks by means of the application of a hybrid finite-discrete element method. This method allows for a proper simulation of the brittle rock behaviour and the related mechanism of fracture propagation. In particular, the paper presents two ideal problems, represented by a shallow underground cave and a vertical cliff, for which the evolution of the stability conditions is investigated by comparing the solutions obtained implementing different brittle material responses with those resulting from the assumption of perfectly

Contribution of Underlying Connective Tissue Cells to Taste Buds in Mouse Tongue and Soft Palate

Science.gov (United States)

Mederacke, Ingmar; Komatsu, Yoshihiro; Stice, Steve; Schwabe, Robert F.; Mistretta, Charlotte M.; Mishina, Yuji; Liu, Hong-Xiang

2016-01-01

Taste buds, the sensory organs for taste, have been described as arising solely from the surrounding epithelium, which is in distinction from other sensory receptors that are known to originate from neural precursors, i.e., neural ectoderm that includes neural crest (NC). Our previous study suggested a potential contribution of NC derived cells to early immature fungiform taste buds in late embryonic (E18.5) and young postnatal (P1-10) mice. In the present study we demonstrated the contribution of the underlying connective tissue (CT) to mature taste buds in mouse tongue and soft palate. Three independent mouse models were used for fate mapping of NC and NC derived connective tissue cells: (1) P0-Cre/R26-tdTomato (RFP) to label NC, NC derived Schwann cells and derivatives; (2) Dermo1-Cre/RFP to label mesenchymal cells and derivatives; and (3) Vimentin-CreER/mGFP to label Vimentin-expressing CT cells and derivatives upon tamoxifen treatment. Both P0-Cre/RFP and Dermo1-Cre/RFP labeled cells were abundant in mature taste buds in lingual taste papillae and soft palate, but not in the surrounding epithelial cells. Concurrently, labeled cells were extensively distributed in the underlying CT. RFP signals were seen in the majority of taste buds and all three types (I, II, III) of differentiated taste bud cells, with the neuronal-like type III cells labeled at a greater proportion. Further, Vimentin-CreER labeled cells were found in the taste buds of 3-month-old mice whereas Vimentin immunoreactivity was only seen in the CT. Taken together, our data demonstrate a previously unrecognized origin of taste bud cells from the underlying CT, a conceptually new finding in our knowledge of taste bud cell derivation, i.e., from both the surrounding epithelium and the underlying CT that is primarily derived from NC. PMID:26741369

Contribution of Underlying Connective Tissue Cells to Taste Buds in Mouse Tongue and Soft Palate.

Directory of Open Access Journals (Sweden)

Kristin Boggs

Full Text Available Taste buds, the sensory organs for taste, have been described as arising solely from the surrounding epithelium, which is in distinction from other sensory receptors that are known to originate from neural precursors, i.e., neural ectoderm that includes neural crest (NC. Our previous study suggested a potential contribution of NC derived cells to early immature fungiform taste buds in late embryonic (E18.5 and young postnatal (P1-10 mice. In the present study we demonstrated the contribution of the underlying connective tissue (CT to mature taste buds in mouse tongue and soft palate. Three independent mouse models were used for fate mapping of NC and NC derived connective tissue cells: (1 P0-Cre/R26-tdTomato (RFP to label NC, NC derived Schwann cells and derivatives; (2 Dermo1-Cre/RFP to label mesenchymal cells and derivatives; and (3 Vimentin-CreER/mGFP to label Vimentin-expressing CT cells and derivatives upon tamoxifen treatment. Both P0-Cre/RFP and Dermo1-Cre/RFP labeled cells were abundant in mature taste buds in lingual taste papillae and soft palate, but not in the surrounding epithelial cells. Concurrently, labeled cells were extensively distributed in the underlying CT. RFP signals were seen in the majority of taste buds and all three types (I, II, III of differentiated taste bud cells, with the neuronal-like type III cells labeled at a greater proportion. Further, Vimentin-CreER labeled cells were found in the taste buds of 3-month-old mice whereas Vimentin immunoreactivity was only seen in the CT. Taken together, our data demonstrate a previously unrecognized origin of taste bud cells from the underlying CT, a conceptually new finding in our knowledge of taste bud cell derivation, i.e., from both the surrounding epithelium and the underlying CT that is primarily derived from NC.

Contribution of Underlying Connective Tissue Cells to Taste Buds in Mouse Tongue and Soft Palate.

Science.gov (United States)

Boggs, Kristin; Venkatesan, Nandakumar; Mederacke, Ingmar; Komatsu, Yoshihiro; Stice, Steve; Schwabe, Robert F; Mistretta, Charlotte M; Mishina, Yuji; Liu, Hong-Xiang

2016-01-01

Taste buds, the sensory organs for taste, have been described as arising solely from the surrounding epithelium, which is in distinction from other sensory receptors that are known to originate from neural precursors, i.e., neural ectoderm that includes neural crest (NC). Our previous study suggested a potential contribution of NC derived cells to early immature fungiform taste buds in late embryonic (E18.5) and young postnatal (P1-10) mice. In the present study we demonstrated the contribution of the underlying connective tissue (CT) to mature taste buds in mouse tongue and soft palate. Three independent mouse models were used for fate mapping of NC and NC derived connective tissue cells: (1) P0-Cre/R26-tdTomato (RFP) to label NC, NC derived Schwann cells and derivatives; (2) Dermo1-Cre/RFP to label mesenchymal cells and derivatives; and (3) Vimentin-CreER/mGFP to label Vimentin-expressing CT cells and derivatives upon tamoxifen treatment. Both P0-Cre/RFP and Dermo1-Cre/RFP labeled cells were abundant in mature taste buds in lingual taste papillae and soft palate, but not in the surrounding epithelial cells. Concurrently, labeled cells were extensively distributed in the underlying CT. RFP signals were seen in the majority of taste buds and all three types (I, II, III) of differentiated taste bud cells, with the neuronal-like type III cells labeled at a greater proportion. Further, Vimentin-CreER labeled cells were found in the taste buds of 3-month-old mice whereas Vimentin immunoreactivity was only seen in the CT. Taken together, our data demonstrate a previously unrecognized origin of taste bud cells from the underlying CT, a conceptually new finding in our knowledge of taste bud cell derivation, i.e., from both the surrounding epithelium and the underlying CT that is primarily derived from NC.

Leading multi-soft limits from scattering equations

Science.gov (United States)

Zlotnikov, Michael

2017-10-01

A Cachazo-He-Yuan (CHY) type formula is derived for the leading gluon, bi-adjoint scalar ϕ 3, Yang-Mills-scalar and non-linear sigma model m-soft factors S m in arbitrary dimension. The general formula is used to evaluate explicit examples for up to three soft legs analytically and up to four soft legs numerically via comparison with amplitude ratios under soft kinematics. A structural pattern for gluon m-soft factor is inferred and a simpler formula for its calculation is conjectured. In four dimensions, a Cachazo-Svrček-Witten (CSW) recursive procedure producing the leading m-soft gluon factor in spinor helicity formalism is developed as an alternative, and Britto-Cachazo-Feng-Witten (BCFW) recursion is used to obtain the leading four-soft gluon factor for all analytically distinct helicity configurations.

Analyzing Reliability and Performance Trade-Offs of HLS-Based Designs in SRAM-Based FPGAs Under Soft Errors

Science.gov (United States)

Tambara, Lucas Antunes; Tonfat, Jorge; Santos, André; Kastensmidt, Fernanda Lima; Medina, Nilberto H.; Added, Nemitala; Aguiar, Vitor A. P.; Aguirre, Fernando; Silveira, Marcilei A. G.

2017-02-01

The increasing system complexity of FPGA-based hardware designs and shortening of time-to-market have motivated the adoption of new designing methodologies focused on addressing the current need for high-performance circuits. High-Level Synthesis (HLS) tools can generate Register Transfer Level (RTL) designs from high-level software programming languages. These tools have evolved significantly in recent years, providing optimized RTL designs, which can serve the needs of safety-critical applications that require both high performance and high reliability levels. However, a reliability evaluation of HLS-based designs under soft errors has not yet been presented. In this work, the trade-offs of different HLS-based designs in terms of reliability, resource utilization, and performance are investigated by analyzing their behavior under soft errors and comparing them to a standard processor-based implementation in an SRAM-based FPGA. Results obtained from fault injection campaigns and radiation experiments show that it is possible to increase the performance of a processor-based system up to 5,000 times by changing its architecture with a small impact in the cross section (increasing up to 8 times), and still increasing the Mean Workload Between Failures (MWBF) of the system.

Moisture expansion of ceramic tiles produced using kaolin and granite wastes; Expansao por umidade de revestimentos ceramicos incorporados com residuos de granito e caulim

Energy Technology Data Exchange (ETDEWEB)

Mendonca, A.M.G.D.; Cartaxo, J.M.; Santana, L.N.L; Neves, G.A.; Ferreira, H.C., E-mail: ana.duartemendonca@gmail.com, E-mail: gelmires@dema.ufcg.edu.br, E-mail: lisiane@dema.ufcg.edu.br [Unidade Academica de Engenharia de Materiais, Universidade Federal de Campina Grande,Campina Grande, PB (Brazil); Menezes, R.R. [Departamento de Engenharia de Materiais, Universidade Federal da Paraiba, Joao Pessoa, PB (Brazil)

2012-04-15

Moisture expansion (ME) is the term used to describe the expansion of ceramic materials due to the adsorption of water. ME usually occurs slowly and is relatively small, but, it can damage the ceramic tiles adhesion to the underlayment, craze the glaze and lead to the development of cracks on ceramics bricks. In this work kaolin and granite wastes were incorporated in ceramic compositions aiming study their influence on the ME of ceramic tiles. Raw materials were processed and submitted to characterization: physical and mineralogical by laser diffraction particle size analysis, chemical analysis, thermo differential and thermogravimetric analysis and X-ray diffraction. Results showed that kaolin and granite wastes can be incorporated in ceramic composition because display characteristics similar to conventional not plastic ceramic materials, providing satisfactory ME results when compared to the ME limit value of 0.6 mm/m (0.06%) indicated by the ABNT for ceramic tiles. Compositions containing up to 20% of waste can be produced when firing above 1000 deg C. (author)

Planning of the in-situ creep test in sedimentary soft rocks under high temperature

International Nuclear Information System (INIS)

Takakura, Nozomu; Yoshikawa, Kazuo; Okada, Tetsuji; Sawada, Masataka; Tani, Kazuo; Takeda, Kayo

2007-01-01

Research has been conducted on underground facilities for energy storage and waste disposal in sedimentary soft rocks. One of the research topics is that the long-term mechanical behaviors of sedimentary soft rocks can be affected by various environmental factors such as temperatures or hydraulic conditions. Therefore, it is necessary to develop a method for evaluating the long-term stability of caverns in sedimentary soft rocks as influenced by changes in the external environment. This report presents the plan of field creep test for the purpose to establish the evaluation method of long-term stability of caverns in soft rocks. A series of field creep test is performed to study the influence of high temperature in an underground facility at a depth of 50 meters. (author)

Bulk Fluidity and Apparent Wall Slip of Aqueous Kaolin Suspensions Studied Using the Cone-Cone (KK) Sensor: Effect of the Sensor Surface Quality.

Czech Academy of Sciences Publication Activity Database

Pěnkavová, Věra; Tihon, Jaroslav; Wein, Ondřej

2017-01-01

Roč. 533, NOV 20 (2017), s. 338-346 ISSN 0927-7757 EU Projects: Foundation for Science and Technology(XE) MP1305 Institutional support: RVO:67985858 Keywords : aqueous kaolin suspensions * rotational AWS viscometry * apparent wall slip Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 2.714, year: 2016

Synthesis and characterization of a novel Mg–Al hydrotalcite-loaded kaolin clay and its adsorption properties for phosphate in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Deng, Lin, E-mail: denglinlyn@126.com; Shi, Zhou, E-mail: 369329062@qq.com

2015-07-15

Highlights: • Kaolin clay was coalesced with Mg–Al hydrotalcite to form composite adsorbent (MKC). • MKC was synthesized through modified co-precipitation method. • MKC gave high adsorption of phosphate over a wide pH range of 2.5–9.5. • MKC is an economical and environmentally friendly adsorbent for phosphate removal and recycling. - Abstract: The mesoporous modified kaolin clay (MKC) was synthesized by loading Mg–Al hydrotalcite onto kaolin clay through coprecipitation method and applied for adsorption of phosphate from aqueous solution. Several techniques, including Brunauer–Emmett–Teller (BET), thermal analysis (TG–DTA), and Fourier transform infrared spectroscopy (FTIR) were employed to characterize the adsorbents. The effects of adsorbent dosage, solution pH, initial phosphate concentration, contact time, temperature, and coexistent anions on phosphate adsorption have been investigated. MKC exhibited a strong uptake affinity to phosphate in a wide pH range of 2.5–9.5, with the maximum adsorptive removal of 98.03%, at adsorbent dosage of 0.2 g/50 mL, pH 7.5, and initial phosphate concentration 25 mg L{sup −1}. The adsorption kinetics followed the pseudo-second-order kinetic model. The Langmuir isothermal model well described the adsorption isotherm data, showing a maximum adsorption capacity for phosphate up to 11.92 mg g{sup −1} at 298 K. The obtained thermodynamic parameters revealed that the adsorption of phosphate onto MKC was an exothermic and spontaneous process. Coexistent chloride, nitrate, and sulfate ions displayed an adverse effect on phosphate adsorption following the order of SO{sub 4}{sup 2−} > NO{sub 3}{sup −} > Cl{sup −}. A mechanism of adsorption that involved (i) electrostatic attraction of hydroxyl groups of the adsorbent with negatively charged phosphate ions, and (ii) anion exchange of NO{sub 3}{sup −} ions that were associated with the surface or interlayer of the adsorbent with anionic phosphate ions in

Synthesis and characterization of a novel Mg–Al hydrotalcite-loaded kaolin clay and its adsorption properties for phosphate in aqueous solution

International Nuclear Information System (INIS)

Deng, Lin; Shi, Zhou

2015-01-01

Highlights: • Kaolin clay was coalesced with Mg–Al hydrotalcite to form composite adsorbent (MKC). • MKC was synthesized through modified co-precipitation method. • MKC gave high adsorption of phosphate over a wide pH range of 2.5–9.5. • MKC is an economical and environmentally friendly adsorbent for phosphate removal and recycling. - Abstract: The mesoporous modified kaolin clay (MKC) was synthesized by loading Mg–Al hydrotalcite onto kaolin clay through coprecipitation method and applied for adsorption of phosphate from aqueous solution. Several techniques, including Brunauer–Emmett–Teller (BET), thermal analysis (TG–DTA), and Fourier transform infrared spectroscopy (FTIR) were employed to characterize the adsorbents. The effects of adsorbent dosage, solution pH, initial phosphate concentration, contact time, temperature, and coexistent anions on phosphate adsorption have been investigated. MKC exhibited a strong uptake affinity to phosphate in a wide pH range of 2.5–9.5, with the maximum adsorptive removal of 98.03%, at adsorbent dosage of 0.2 g/50 mL, pH 7.5, and initial phosphate concentration 25 mg L −1 . The adsorption kinetics followed the pseudo-second-order kinetic model. The Langmuir isothermal model well described the adsorption isotherm data, showing a maximum adsorption capacity for phosphate up to 11.92 mg g −1 at 298 K. The obtained thermodynamic parameters revealed that the adsorption of phosphate onto MKC was an exothermic and spontaneous process. Coexistent chloride, nitrate, and sulfate ions displayed an adverse effect on phosphate adsorption following the order of SO 4 2− > NO 3 − > Cl − . A mechanism of adsorption that involved (i) electrostatic attraction of hydroxyl groups of the adsorbent with negatively charged phosphate ions, and (ii) anion exchange of NO 3 − ions that were associated with the surface or interlayer of the adsorbent with anionic phosphate ions in solution, was proposed

Color and shade parameters of ultramarine zeolitic pigments synthesized from kaolin waste

International Nuclear Information System (INIS)

Menezes, Raquel Aranha de; Paz, Simone Patricia Aranha da; Angelica, Romulo Simoes; Neves, Roberto de Freitas; Pergher, Sibele Berenice Castella

2014-01-01

Ultramarine pigments were successful synthesized from zeolite A obtained from kaolin waste. This waste has been used as an excellent source of silicon and aluminum for zeolite synthesis because of its high kaolinite concentrations and low contents of other accessory minerals. The cost is naturally less than the industrialized product. Color additives (Sulfur and Sodium Carbonate) were mixed with different proportions of zeolite A and further calcined for 5 h at 500 °C. They were characterized by XRD and XRF in addition to visual classification by color and shade. These products show colors from blue to green at different shades, both influenced by the amount of additives and cooling rate after calcination. Thus, a different quantity of the same additives in the same zeolitic matrix provides an increase in the color intensity. Cooling rate after calcination induces the color change which is substantially important in the pigments production. (author)

Color and shade parameters of ultramarine zeolitic pigments synthesized from kaolin waste

Energy Technology Data Exchange (ETDEWEB)

Menezes, Raquel Aranha de; Paz, Simone Patricia Aranha da; Angelica, Romulo Simoes; Neves, Roberto de Freitas; Pergher, Sibele Berenice Castella, E-mail: raquel_arn@hotmail.com [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Geociencias. Grupo de Mineralogia e Geoquimica Aplicada

2014-08-15

Ultramarine pigments were successful synthesized from zeolite A obtained from kaolin waste. This waste has been used as an excellent source of silicon and aluminum for zeolite synthesis because of its high kaolinite concentrations and low contents of other accessory minerals. The cost is naturally less than the industrialized product. Color additives (Sulfur and Sodium Carbonate) were mixed with different proportions of zeolite A and further calcined for 5 h at 500 °C. They were characterized by XRD and XRF in addition to visual classification by color and shade. These products show colors from blue to green at different shades, both influenced by the amount of additives and cooling rate after calcination. Thus, a different quantity of the same additives in the same zeolitic matrix provides an increase in the color intensity. Cooling rate after calcination induces the color change which is substantially important in the pigments production. (author)

Sintering of anorthite based ceramics prepared from kaolin DD2 and calcite

Energy Technology Data Exchange (ETDEWEB)

Zaiou, S.; Harabi, A.; Harabi, E.; Guechi, A.; Karboua, N.; Benhassine, M.-T.; Zouai, S.; Guerfa, F., E-mail: Zaiou_21@yahoo.fr, E-mail: harabi52@gmail.com, E-mail: semouni84@gmail.com, E-mail: guechia@yahoo.fr, E-mail: kanour17@yahoo.fr, E-mail: mtb25dz@gmail.com, E-mail: zouaisouheila@yahoo.fr, E-mail: guerfatiha@gmail.com [Ceramics Lab., Faculty of Exact Science, Physics Department, Mentouri University of Constantine (Algeria)

2016-10-15

In this work, the preparation of anorthite based ceramics using a modified milling system and 80 wt% kaolin (DD2 type) and 20 wt% calcium oxide extracted from CaCO{sub 3} is shown. The choice of these raw materials was dictated by their natural abundance. Previous studies have shown that a simple and vibratory multidirectional milling system using a bimodal distribution of highly resistant ceramics can be successfully used for obtaining fine powders. The prepared samples were sintered at different temperatures ranging between 800 and 1100 °C. It has been found that the relative density of samples sintered at 900 °C for 1 h with a heating rate of 5 °C/min was about 96% of the theoretical density of anorthite (2.75 g/cm{sup 3} ). Finally, the prepared samples were also characterized by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. (author)

Sintering of anorthite based ceramics prepared from kaolin DD2 and calcite

Directory of Open Access Journals (Sweden)

S. Zaiou

Full Text Available Abstract In this work, the preparation of anorthite based ceramics using a modified milling system and 80 wt% kaolin (DD2 type and 20 wt% calcium oxide extracted from CaCO3 is shown. The choice of these raw materials was dictated by their natural abundance. Previous studies have shown that a simple and vibratory multidirectional milling system using a bimodal distribution of highly resistant ceramics can be successfully used for obtaining fine powders. The prepared samples were sintered at different temperatures ranging between 800 and 1100 °C. It has been found that the relative density of samples sintered at 900 °C for 1 h with a heating rate of 5 °C/min was about 96% of the theoretical density of anorthite (2.75 g/cm3. Finally, the prepared samples were also characterized by scanning electron microscopy, X-ray diffraction and Raman spectroscopy.

Sintering of anorthite based ceramics prepared from kaolin DD2 and calcite

International Nuclear Information System (INIS)

Zaiou, S.; Harabi, A.; Harabi, E.; Guechi, A.; Karboua, N.; Benhassine, M.-T.; Zouai, S.; Guerfa, F.

2016-01-01

In this work, the preparation of anorthite based ceramics using a modified milling system and 80 wt% kaolin (DD2 type) and 20 wt% calcium oxide extracted from CaCO 3 is shown. The choice of these raw materials was dictated by their natural abundance. Previous studies have shown that a simple and vibratory multidirectional milling system using a bimodal distribution of highly resistant ceramics can be successfully used for obtaining fine powders. The prepared samples were sintered at different temperatures ranging between 800 and 1100 °C. It has been found that the relative density of samples sintered at 900 °C for 1 h with a heating rate of 5 °C/min was about 96% of the theoretical density of anorthite (2.75 g/cm 3 ). Finally, the prepared samples were also characterized by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. (author)

Interpretation of the stiffness and permeability of Sand-Kaolin mixtures in the framework of homogenization

Directory of Open Access Journals (Sweden)

Claude Boutin

2010-03-01

Full Text Available This study deals with the behaviour of mixtures of sand and saturated kaolin paste considered as composite materials made of permeable and deformable (with non-linear behaviour matrix (the kaolin paste with rigid and impervious inclusions (the sand grains. Oedometric and permeability tests conducted on such mixtures highlight the key role of the state of the clay paste, and show the existence of a threshold of sand grain concentration above which a structuring effect influences both modulus and permeability. At the light of these experiments, the usual and tangent homogenization process (with simplifying assumptions to make the problem manageable has been applied to estimate the mixture permeability and tangent compressibility. Qualitative and quantitative comparisons with experimental data point out the domain of interest and the limitations of such approaches.O estudo lida com o comportamento de misturas compostas por areia e uma pasta de caulinita considerada um material composto feito de uma matriz (caulinita permeável e deformável (com comportamento não-linear com inclusões rígidas e impermeáveis (grãos de areia. Testes de permeabilidade e odométricos conduzidos nestas misturas enfatizam o papel chave de estado da pasta argilosa e mostram a existência de uma concentração crítica de grãos de areia com efeito estruturante que influencia o módulo e a permeabilidade. Sob a luz destes experimentos o processo de homogeneização usual e tangente (com hipóteses simplificadoras para tornar o problema tratável foi aplicado para estimar a permeabilidade da mistura e a compressibilidade tangente. Comparações qualitativas e quantitativas com dados experimentais apontam o domínio de interesse bem como a limitação destas abordagens.

Electrospray soft-landing for the construction of non-covalent molecular nanostructures using charged droplets under ambient conditions.

Science.gov (United States)

Hou, Jian; Zheng, Qingna; Badu-Tawiah, Abraham K; Xiong, Caiqiao; Guan, Cuizhong; Chen, Suming; Nie, Zongxiu; Wang, Dong; Wan, Lijun

2016-11-17

An electrospray soft-landing (SL) technique was utilized to create 2D nano-networks on HOPG under ambient conditions. A 2,3,6,7,10,11-hexahydroxy-triphenylene close-packing structure was observed by STM instead of unorganized clusters, as well as amine and acid nanostructures. On C 18 H 37 NH 2 networks, C 18 H 37 NH 3 + was identified by XPS analysis revealing retaining of charges on the SL-modified surface.

ATLAS soft QCD results

CERN Document Server

Sykora, Tomas; The ATLAS collaboration

2018-01-01

Recent results of soft QCD measurements performed by the ATLAS collaboration are reported. The measurements include total, elastic and inelastic cross sections, inclusive spectra, underlying event and particle correlations in p-p and p-Pb collisions.

Statistical quality analysis of schedulers under soft-real-time constraints

NARCIS (Netherlands)

Baarsma, H.E.; Hurink, Johann L.; Jansen, P.G.

2007-01-01

This paper describes an algorithm to determine the performance of real-time systems with tasks using stochastic processing times. Such an algorithm can be used for guaranteeing Quality of Service of periodic tasks with soft real-time constraints. We use a discrete distribution model of processing

Unbelievable but true: Partial thromboplastin time, kaolin 120 s and yet no surgical bleed!

Directory of Open Access Journals (Sweden)

Shagun Bhatia Shah

2017-01-01

Full Text Available Partial thromboplastin time, kaolin (PTTK is a global test sensitive to low levels of all the coagulation factors, except Factor VII and Factor XIII. Patients with extensive cancer have a propensity to develop a shortened PTTK. Our breast cancer patient had a prolonged PTTK result roughly 4 times the normal values. A detailed description of the preoperative workup including the special investigations is required to ascertain the cause of the prolongation and precautions taken, leading to successful breast cancer surgery and postoperative period in this patient follows. Allowing the surgeon to operate a patient with a PTTK >120 s and simultaneously at risk of thrombosis due to lupus anticoagulant is possible with a calculated risk and thorough preoperative evaluation. Prophylactic fresh frozen plasma and deep venous thrombosis prophylaxis have an important role.

Multisensory softness perceived compliance from multiple sources of information

CERN Document Server

Luca, Massimiliano Di

2014-01-01

Offers a unique multidisciplinary overview of how humans interact with soft objects and how multiple sensory signals are used to perceive material properties, with an emphasis on object deformability. The authors describe a range of setups that have been employed to study and exploit sensory signals involved in interactions with compliant objects as well as techniques to simulate and modulate softness - including a psychophysical perspective of the field. Multisensory Softness focuses on the cognitive mechanisms underlying the use of multiple sources of information in softness perception. D

Soft Ultrathin Electronics Innervated Adaptive Fully Soft Robots.

Science.gov (United States)

Wang, Chengjun; Sim, Kyoseung; Chen, Jin; Kim, Hojin; Rao, Zhoulyu; Li, Yuhang; Chen, Weiqiu; Song, Jizhou; Verduzco, Rafael; Yu, Cunjiang

2018-03-01

Soft robots outperform the conventional hard robots on significantly enhanced safety, adaptability, and complex motions. The development of fully soft robots, especially fully from smart soft materials to mimic soft animals, is still nascent. In addition, to date, existing soft robots cannot adapt themselves to the surrounding environment, i.e., sensing and adaptive motion or response, like animals. Here, compliant ultrathin sensing and actuating electronics innervated fully soft robots that can sense the environment and perform soft bodied crawling adaptively, mimicking an inchworm, are reported. The soft robots are constructed with actuators of open-mesh shaped ultrathin deformable heaters, sensors of single-crystal Si optoelectronic photodetectors, and thermally responsive artificial muscle of carbon-black-doped liquid-crystal elastomer (LCE-CB) nanocomposite. The results demonstrate that adaptive crawling locomotion can be realized through the conjugation of sensing and actuation, where the sensors sense the environment and actuators respond correspondingly to control the locomotion autonomously through regulating the deformation of LCE-CB bimorphs and the locomotion of the robots. The strategy of innervating soft sensing and actuating electronics with artificial muscles paves the way for the development of smart autonomous soft robots. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Characterization of kaolin and granite waste for formulation of porcelain stoneware tiles; Caracterizacao de caulim e de residuo de granito para formulacao de gres porcelanato

Energy Technology Data Exchange (ETDEWEB)

Luna da Silveira, G.C. [Instituto Federal do Rio Grande do Norte (IFRN), RN (Brazil); Acchar, W.; Gomes, U.U.; Silva, B.K.O.; Luna da Silveira, R.V. [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil); Labrincha, J.A.; Costa, M.C.P., E-mail: glebacoelli@hotmail.com [Universidade de Aveiro (Portugal)

2016-07-01

To produce a stoneware tiles is necessary develop a formulation that satisfies their structural characteristics, micro-structural, physical and mechanical properties. Thus, in order to create a formulation for porcelain stoneware tiles that give use to kaolin and granite waste used in the production of ceramic materials were asked the following characterizations: chemical analysis, mineralogical, thermal and particle size. We found that in the kaolin sample it presents a rate of silicon oxide and aluminum oxide similar to those found in the work of other investigators, about 45.23% SiO2 and 37.39% Al{sub 2}O{sub 3}. In the granite waste, the percentage of silicon oxide and aluminum oxide are also similar to those observed in other studies, with about 74.89% SiO2 and 10.54% Al{sub 2}O{sub 3}. Both the percentage of SiO{sub 2} and Al{sub 2}O{sub 3} founded in these two samples satisfy the percentage required in the manufacturing of porcelain stoneware tiles. (author)

A biphasic model for bleeding in soft tissue

Science.gov (United States)

Chang, Yi-Jui; Chong, Kwitae; Eldredge, Jeff D.; Teran, Joseph; Benharash, Peyman; Dutson, Erik

2017-11-01

The modeling of blood passing through soft tissues in the body is important for medical applications. The current study aims to capture the effect of tissue swelling and the transport of blood under bleeding or hemorrhaging conditions. The soft tissue is considered as a non-static poro-hyperelastic material with liquid-filled voids. A biphasic formulation effectively, a generalization of Darcy's law-is utilized, treating the phases as occupying fractions of the same volume. The interaction between phases is captured through a Stokes-like friction force on their relative velocities and a pressure that penalizes deviations from volume fractions summing to unity. The soft tissue is modeled as a hyperelastic material with a typical J-shaped stress-strain curve, while blood is considered as a Newtonian fluid. The method of Smoothed Particle Hydrodynamics is used to discretize the conservation equations based on the ease of treating free surfaces in the liquid. Simulations of swelling under acute hemorrhage and of draining under gravity and compression will be demonstrated. Ongoing progress in modeling of organ tissues under injuries and surgical conditions will be discussed.

Magnetic zeolites a and p synthesized from kaolin: synthesis and characterization

Energy Technology Data Exchange (ETDEWEB)

Bessa, R.A.; Oliveira, C.P.; Nascimento, R.F.; Bohn, F.; Loiola, A.R. [Universidade Federal do Ceara (UFCE), CE (Brazil)

2016-07-01

Full text: Zeolites are hydrated aluminosilicates of open chain, formed by silica and alumina tetrahedral structures linked by common oxygen atoms, generating interconnected pores and cages with molecular dimensions and well defined sizes that limit matter transference between internal surface and application medium. They can be found naturally or synthesized using different aluminum and silicon sources that may modify the produced zeolite. Their industrial application has grown enormously over the last century. However, a big issue that still remains is the difficulty in retrieving zeolite powders when used in aqueous media. This work reports the use of kaolin as an alternative raw material for zeolite syntheses by means of hydrothermal route and subsequent preparation of magnetic composites through magnetite impregnation. The syntheses of two different zeolites were carried out by mixing appropriate amounts of metakaolin (kaolin previously calcined at 600 deg C for 2 h), sodium metasilicate and sodium hydroxide solution, aged for 18 h and heated at 100 °C for 4-48 h. After these processes, the final materials were washed several times with distilled water, filtered and dried at 80 deg C for 12 h. Magnetic composites were prepared by impregnating the zeolites with of Fe3O4 nanoparticles (NP) synthesized by the partial oxidation and precipitation of Fe2+ ions. The obtained materials were characterized by X-ray diffraction, scanning electron microscopy, FTIR spectroscopy and magnetization measurements. The results of XRD and FTIR provide evidence of the success in the synthesis of both zeolites A and P as well as Fe3O4. Subsequently, composites were formed by mixtures of zeolite A + NP and zeolite P + NP. The existence of secondary crystalline phases was also confirmed. However, it did not interfered significantly in the results as these phases appear as minor amounts and are most likely residues from the clay used as the main silica and alumina sources. Scanning

Production of zeolite A come from rio Capim Kaolin: Study on recycle of sodium hydroxide solution

International Nuclear Information System (INIS)

Moraes, C.G.; Rodrigues, E.C.; Rocha Junior, C.A.F.; Macedo, E.N.; Neves, R.F.

2011-01-01

The kaolin processing industry is an important economic sector in the State of Para, but produces huge amounts of wastes composed essentially of kaolinite. The production processes of zeolites typically use sodium hydroxide in excess, are discarded. So the objective is the development process for production of zeolite A which allows the reuse of the solution of sodium hydroxide used in excess through your recycling. Presents the results of XRD, SEM of the zeolites produced in five consecutive cycles performed at a temperature of 110°C/24h as a source of sodium hydroxide solution of sodium 5 M, using a molar ratio of Si/Al = 1 and Na/Al = 1,26. (author)

20051008 NATO Advanced Research Workshop on Soft Matter under Exogenic Impacts Fundamentals and Emerging Technologies Odessa, Ukraine 08 - 12 Oct 2005 2005 odessa20051008 UA 20051012

CERN Document Server

Rzoska, Sylwester J

2007-01-01

‘Soft Matter Under Exogenic Impacts’ is fairly unique in supplying a comprehensive presentation of high pressures, negative pressures, random constraints and strong electric field exogenic (external) impacts on various soft matter systems. These are: (i) critical liquids, (ii) glass formers, such as supercooled liquids including water, polymers and resins, (iii) liquid crystals and (iv) bio-liquids. It is, because of this, an excellent guide in this novel and still puzzling research area. Besides new results, the identification of new types of physical behavior, new technological materials, ultimate verification of condensed and soft matter physics models, new applications in geophysics, biophysics, biotechnology, are all discussed in this book.

Leakage Current Waveforms and Arcing Characteristics of Epoxy Resin for Outdoor Insulators under Clean and Salt Fogs

Directory of Open Access Journals (Sweden)

Suwarno

2008-05-01

Full Text Available Ceramic outdoor insulators have been used in high voltage transmission lines since long time ago. Due to superiority in their resistance to pollution, recently, polymeric outdoor insulators are widely used. Epoxy resin is one polymer which shows good properties for outdoor insulation. During service, outdoor insulators may severe a certain degree of pollution which may reduce their surface resistance. Leakage current (LC usually increase and degradation may take place. This paper reports experimental results on the leakage current waveforms and arcing characteristics of epoxy resin under clean and salt fog. The samples used are blocks of epoxy resin with dimension of 250 x 50 x 20 mm3. The samples were put in a test chamber with dimension of 900x900x1200 mm3 with controllable humidity and pollution conditions. Clean and salt fog were generated according to IEC 60-1 and 507. The arcing experiment was done with incline plane test in accordance with IEC 587. AC voltage in the range from 5 kV to 50 kV with frequency of 50 Hz was applied. The LC waveforms up to flash over were measured. The magnitudes as well as harmonic content of the LC were analyzed. The correlation between LC waveforms and dry band arching phenomenon was elaborated. Visual observation of the arc on the sample surfaces was observed using a video camera. Experimental results indicated that LC magnitude on clean samples was slightly affected by humidity (RH. However, under salt fog, RH greatly affected the LC magnitude. The flashover voltage of clean samples under salt fog reduced significantly for fog conductivity of more than 1.2 mS/cm. Kaolin-polluted samples under salt fog showed an Ohmic behaviour. The LC magnitude was high and a large discrepancy of LC magnitude was observed for high applied voltage of larger than 25 kV. The largest LC magnitude was observed on salt-kaolin polluted samples under clean fog at high RH. LC waveforms analysis indicated that in general LC waveforms

Soft Robotics Week

CERN Document Server

Rossiter, Jonathan; Iida, Fumiya; Cianchetti, Matteo; Margheri, Laura

2017-01-01

This book offers a comprehensive, timely snapshot of current research, technologies and applications of soft robotics. The different chapters, written by international experts across multiple fields of soft robotics, cover innovative systems and technologies for soft robot legged locomotion, soft robot manipulation, underwater soft robotics, biomimetic soft robotic platforms, plant-inspired soft robots, flying soft robots, soft robotics in surgery, as well as methods for their modeling and control. Based on the results of the second edition of the Soft Robotics Week, held on April 25 – 30, 2016, in Livorno, Italy, the book reports on the major research lines and novel technologies presented and discussed during the event.

From Soft Sculpture to Soft Robotics: Retracing a Physical Aesthetics of Bio-Morphic Softness

DEFF Research Database (Denmark)

Jørgensen, Jonas

2017-01-01

Soft robotics has in the past decade emerged as a growing subfield of technical robotics research, distinguishable by its bio-inspired design strategies, interest in morphological computation, and interdisciplinary combination of insights from engineering, computer science, biology and material...... science. Recently, soft robotics technology has also started to make its way into art, design, and architecture. This paper attempts to think an aesthetics of softness and the life-like through an artistic tradition deeply imbricated with an interrogation of softness and its physical substrates, namely...... the soft sculpture that started proliferating in the late 1960s. Critical descriptions of these works, interestingly, frequently emphasize their similarities with living organisms and bodies as a central tenet of their aesthetics. The paper seeks to articulate aspects of a contiguity between softness...

The soft notion of China's 'soft power'

OpenAIRE

Breslin, Shaun

2011-01-01

· Although debates over Chinese soft power have increased in\\ud recent years, there is no shared definition of what ‘soft power’\\ud actually means. The definition seems to change depending on\\ud what the observer wants to argue.\\ud · External analyses of soft power often include a focus on\\ud economic relations and other material (hard) sources of power\\ud and influence.\\ud · Many Chinese analyses of soft power focus on the promotion of a\\ud preferred (positive) understanding of China’s inter...

Botanicals to Control Soft Rot Bacteria of Potato

Directory of Open Access Journals (Sweden)

M. M. Rahman

2012-01-01

Full Text Available Extracts from eleven different plant species such as jute (Corchorus capsularis L., cheerota (Swertia chiraita Ham., chatim (Alstonia scholaris L., mander (Erythrina variegata, bael (Aegle marmelos L., marigold (Tagetes erecta, onion (Allium cepa, garlic (Allium sativum L., neem (Azadiracta indica, lime (Citrus aurantifolia, and turmeric (Curcuma longa L. were tested for antibacterial activity against potato soft rot bacteria, E. carotovora subsp. carotovora (Ecc P-138, under in vitro and storage conditions. Previously, Ecc P-138 was identified as the most aggressive soft rot bacterium in Bangladeshi potatoes. Of the 11 different plant extracts, only extracts from dried jute leaves and cheerota significantly inhibited growth of Ecc P-138 in vitro. Finally, both plant extracts were tested to control the soft rot disease of potato tuber under storage conditions. In a 22-week storage condition, the treated potatoes were significantly more protected against the soft rot infection than those of untreated samples in terms of infection rate and weight loss. The jute leaf extracts showed more pronounced inhibitory effects on Ecc-138 growth both in in vitro and storage experiments.

Incorporation of waste and fiber kaolin caroa panels in Medium Density Fiberboard - MDF; Incorporacao de residuos de caulim e fibras de caroa em paineis de media densidade- MDF

Energy Technology Data Exchange (ETDEWEB)

Bezerra, A.F.C.; Santana, L.N.L.; Neves, G.A.; Carvalho, L.H. de; Lopes, F.F.M., E-mail: anaflavia.dema@yahoo.com.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

2012-07-01

Medium-density panels are composites molded under high temperature and pressure which have physical and mechanical properties similar to those of solid wood. Their composition includes eucalyptus grandis fibers and pinus elliotii fibers, but other fibers can be used such as caroa fibers. The goal of this work was to manufacture panels which kaolin waste and caroa fibers and compare their physical, chemical and mechanical of these panels with a others. Both residue and the fibers were characterized by: differential thermal analysis, thermal gravimetric analysis and Xray diffraction. Through the process of pressing the test specimens were fabricated, test samples were evaluated by three point bending, internal bond, water absorption and swelling in thickness. The samples have low levels of thickness swelling, flexural strength and higher tensile and absorption content relative to commercial MDF. (author)

Managing the Difficult Soft Tissue Envelope in Facial and Rhinoplasty Surgery.

Science.gov (United States)

Kosins, Aaron M; Obagi, Zein E

2017-02-01

The nasal soft tissue envelope affects the final rhinoplasty result, and can limit the expected improvement. Currently, no dependable and objective test exists to measure the thickness of the nasal skin and underlying soft tissue. This paper presents a simple, yet reliable method to determine the thickness of the soft tissue envelope. An algorithm is presented for treatment of the dermis and/or soft tissue apart from surgery of the underlying osseocartilaginous structures. Seventy-five patients presenting for primary rhinoplasty underwent visual and ultrasound assessment of their nasal soft tissue envelope. At preoperative evaluation, the Obagi "skin pinch test" was used to assess the thickness of the nasolabial fold and whether or not the skin was oily. Patients were classified based on the pinch thickness. At time of surgery prior to injection of local anesthesia, ultrasonic assessment was done at the nasolabial fold, keystone junction, supratip, and tip to measure the thickness of the nasal dermis and underlying soft tissue. Patients determined to have thin, normal, and thick skin by the "skin pinch test" were found to have a nasolabial fold dermal thickness with an average of 0.7 mm (0.4-1.2 mm), 1.1 mm (0.8-1.8 mm), and 1.4 mm (0.7-2.0 mm). Patients determined to have thin, normal, and thick skin were found to have a dermal thickness at the keystone junction with an average of 0.3 mm (0.2-0.4 mm), 0.5 mm (0.3-1.1 mm), and 0.9 mm (0.6-1.2 mm), respectively. This difference in thickness also translated to the supratip and tip areas measured. However, all areas were also affected by the oiliness of the skin. Soft tissue thickness (SMAS and muscle) underlying the dermis was variable. Patients of non-Caucasian background were more likely to have a thicker soft tissue layer. The "skin pinch test" is an easy and reliable way for the surgeon to evaluate the thickness of the nasal soft tissue envelope. The rhinoplasty surgeon can make decisions pre- and postoperatively

The Effects of Flocculation on the Propagation of Ultrasound in Dilute Kaolin Slurries.

Science.gov (United States)

Austin; Challis

1998-10-01

A broadband ultrasonic spectrometer has been used to measure ultrasonic attenuation and phase velocity dispersion as functions of frequency in kaolin suspensions over a range of solid volume fractions from phi = 0.01 to phi = 0.08 and over a pH range from 3 to 9. The Harker and Temple theory was used to simulate ultrasound propagation in the suspension, using measured slope viscosity, particle size, and size distribution. Simulated results for ultrasonic attenuation and phase velocity agree well with measured values. Both sets of results agree well and show that for volume fractions above phi approximately 0.05 attenuation and velocity dispersion increase for increasing floc size, whereas for volume fractions below phi approximately 0.05 attenuation and velocity dispersion both decrease. It is proposed that the mechanism for this change in behavior around phi approximately 0.05 involves changes in floc density and floc size distribution with phi and pH. Copyright 1998 Academic Press.

Edaravone reduces astrogliosis and apoptosis in young rats with kaolin-induced hydrocephalus.

Science.gov (United States)

Garcia, Camila Araújo Bernardino; Catalão, Carlos Henrique Rocha; Machado, Hélio Rubens; Júnior, Ivair Matias; Romeiro, Thais Helena; Peixoto-Santos, José Eduardo; Santos, Marcelo Volpon; da Silva Lopes, Luiza

2017-03-01

We investigated the possible neuroprotective effects of the free radical scavenger edaravone in experimental hydrocephalus. Seven-day-old Wistar rats were divided into three groups: control group (C), untreated hydrocephalic (H), and hydrocephalic treated with edaravone (EH). The H and EH groups were subjected to hydrocephalus induction by 20% kaolin intracisternal injection. The edaravone (20 mg/kg) was administered daily for 14 days from the induction of hydrocephalus. All animals were daily weighed and submitted to behavioral test and assessment by magnetic resonance imaging. After 14 days, the animals were sacrificed and the brain was removed for histological, immunohistochemical, and biochemical studies. The gain weight was similar between groups from the ninth post-induction day. The open field test performance of EH group was better (p  0.01), germinal matrix (p > 0.05), and cerebral cortex (p > 0.05), as compared to H group. We have demonstrated that administration of edaravone for 14 consecutive days after induction of hydrocephalus reduced astrocyte activity and that it has some beneficial effects over apoptotic cell death.

Influence of inert fillers on shrinkage cracking of meta-kaolin geo-polymers

International Nuclear Information System (INIS)

Kuenzel, C.; Boccaccini, A.R.

2012-01-01

Geo-polymers contain a network of tetrahedral coordinated aluminate and silicate, and are potential materials to immobilize/encapsulate nuclear wastes. They can exhibit shrinkage cracking when water is removed by drying, and in order to use geo-polymers for waste encapsulation this effect needs to be investigated and controlled. In this study, six different fillers were mixed with meta-kaolin and sodium silicate solution at high pH to form geo-polymers, and the influence of filler addition on mechanical properties has been determined. The fillers used were Fe 2 O 3 , Al 2 O 3 , CaCO 3 , sand, glass and rubber and these do not react during geo-polymerisation reactions. Geo-polymers were prepared containing 30 weight percent of filler. The mechanical properties of the geo-polymers were influenced by the type of filler, with low density fillers increasing mortar viscosity. Geo-polymer samples containing fine filler particles exhibited shrinkage cracking on drying. This was not observed when coarser particles were added and these samples also had significantly improved mechanical properties. (authors)

Soft soil strengthening by stone columns: case of the embankment under the bridge “Moulay Youssef” (Rabat/Salé

Directory of Open Access Journals (Sweden)

Nehab Noura

2014-04-01

Full Text Available The soil is generally a heterogeneous material presenting very variable characteristics. In a general way, the main problems related to soils are: low bearing capacity, deformations under static or dynamic loads, large displacements and large settlements of soft soil where the soil moves according to a fixed ground water table. The development of soil mechanics and geotechnical engineering has led to the amelioration of a wide range of soil improvement techniques. These techniques consist in modifying the characteristics of the ground by physical action or by incorporating columnar inclusions made of highly compacted gravel or granular material into the original soil. Stone column is one of the soft ground improvement methods, applicable to a wide range of soil strata and an economical method of support in compressible and cohesive soils. However, there are many difficulties in quantitative analysis of soil column interaction due to the fact that bearing capacity and consolidation behavior of stone column-mat foundation system is affected by various parameters. In the present study, mechanism and various parameters of stone column behavior are investigated by loading tests. Also, tests results are compared to the finite element numerical modeling “Plaxis 2D” (case study: the embankment under the bridge “Moulay Youssef, Rabat/Salé”.

Soft ideal topological space and mixed fuzzy soft ideal topological space

Directory of Open Access Journals (Sweden)

Manash Borah

2019-01-01

Full Text Available In this paper we introduce fuzzy soft ideal and mixed fuzzy soft ideal topological spaces and some properties of this space. Also we introduce fuzzy soft $I$-open set, fuzzy soft $\\alpha$-$I$-open set, fuzzy soft pre-$I$-open set, fuzzy soft semi-$I$-open set and fuzzy soft $\\beta$-$I$-open set and discuss some of their properties.

SoftAR: visually manipulating haptic softness perception in spatial augmented reality.

Science.gov (United States)

Punpongsanon, Parinya; Iwai, Daisuke; Sato, Kosuke

2015-11-01

We present SoftAR, a novel spatial augmented reality (AR) technique based on a pseudo-haptics mechanism that visually manipulates the sense of softness perceived by a user pushing a soft physical object. Considering the limitations of projection-based approaches that change only the surface appearance of a physical object, we propose two projection visual effects, i.e., surface deformation effect (SDE) and body appearance effect (BAE), on the basis of the observations of humans pushing physical objects. The SDE visualizes a two-dimensional deformation of the object surface with a controlled softness parameter, and BAE changes the color of the pushing hand. Through psychophysical experiments, we confirm that the SDE can manipulate softness perception such that the participant perceives significantly greater softness than the actual softness. Furthermore, fBAE, in which BAE is applied only for the finger area, significantly enhances manipulation of the perception of softness. We create a computational model that estimates perceived softness when SDE+fBAE is applied. We construct a prototype SoftAR system in which two application frameworks are implemented. The softness adjustment allows a user to adjust the softness parameter of a physical object, and the softness transfer allows the user to replace the softness with that of another object.

Results of Soft-Diffraction at LHCb

CERN Document Server

Meissner, Marco

2013-01-01

The LHCb detector with its unique pseudorapidity coverage allows to perform soft-QCD measurements in the kinematic forward region where QCD models have large uncertainties. Selected analyses related to soft-Diffraction will be summarised in these proceedings. Energy flow and charged particle multiplicity have been measured separately in different event classes. They give input for modelling the underlying event in $pp$ collisions. Prompt hadron ratios are important for hadronisation models, while the $p/p$ ratio is a good observable to test models of baryon number transport.

Bulk Fluidity and Apparent Wall Slip of Aqueous Kaolin Suspensions Studied Using the Cone-cone (KK) Sensor: The Effect of Concentration and Temperature.

Czech Academy of Sciences Publication Activity Database

Pěnkavová, Věra; Tihon, Jaroslav; Wein, Ondřej

2016-01-01

Roč. 511, DEC 20 (2016), s. 272-284 ISSN 0927-7757 R&D Projects: GA MŠk(CZ) LD13018 Grant - others:COST- European Coperation in Science and Technology(XE) MP1305; COST- European Coperation in Science and Technology(XE) MP1106 Program:LD COST Institutional support: RVO:67985858 Keywords : aqueous kaolin suspensions * apparent wall slip * cone-cone (KK) sensor Subject RIV: CI - Industrial Chemistry , Chemical Engineering Impact factor: 2.714, year: 2016

Effects of using kaolin waste and granite waste as raw materials for the production of low-water absorption ceramic tiles; Efeitos da co-utilizacao dos residuos do beneficiamento do caulim e da extracao do granito rain forest para a producao de revestimentos ceramicos com baixa absorcao de agua

Energy Technology Data Exchange (ETDEWEB)

Freires, H.P.; Argonz, R.; Nogueira, R.E.F.Q.; Sasaki, J.M., E-mail: argonz@ufc.br [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil); Sales, J.C. [Universidade do Vale do Aracau (UVA), Crateus, CE (Brazil)

2012-07-01

This study aims to evaluate the potential of co-use of granite waste (Rain Forest) and kaolin waste as raw material for the manufacture of ceramic coating of low water absorption. Raw materials were characterized by X-ray diffraction. Kaolin residue was added to the residue of granite in the following proportions (in wt%): 0, 10, 20, 30, 40 and 50%. Specimens were fabricated by uniaxial pressing and fired at 1175,1200 and 1225 deg C. Studies of firing linear shrinkage, water absorption, apparent porosity, apparent density and tensile bending test (or rupture modulus) were conducted. The temperature of 1225 deg C allowed the use of a mixture of 50% granite residue and 50% kaolin residue. Ceramic parts made from that mixture exhibited the maximum values required by the Brazilian Standard NBR 13818 for water absorption, shrinkage and density. (author)

In-situ heater test in sedimentary soft rocks under high temperature (Phase I)

International Nuclear Information System (INIS)

Ikenoya, Takafumi; Takakura, Nozomu; Okada, Tetsuji; Sawada, Masataka; Hirano, Kouhei; Tani, Kazuo

2008-01-01

Various researches have been conducted on high level radioactive waste geological disposal in sedimentary soft rocks. It's noted that the long-term mechanical behaviors of sedimentary soft rocks can be affected by various environmental factors such as temperatures or hydraulic conditions. Therefore, in-situ heater test was conducted in an underground cavern at a depth of 50 meters for the purpose of improving thermo-hydro-mechanical coupled analysis code. This report presents the test result demonstrating the changes of temperature and strain distributions with time at the elevated temperature of the heater up to 40 degrees Celsius. (author)

Mechanical transduction via a single soft polymer

Science.gov (United States)

Hou, Ruizheng; Wang, Nan; Bao, Weizhu; Wang, Zhisong

2018-04-01

Molecular machines from biology and nanotechnology often depend on soft structures to perform mechanical functions, but the underlying mechanisms and advantages or disadvantages over rigid structures are not fully understood. We report here a rigorous study of mechanical transduction along a single soft polymer based on exact solutions to the realistic three-dimensional wormlike-chain model and augmented with analytical relations derived from simpler polymer models. The results reveal surprisingly that a soft polymer with vanishingly small persistence length below a single chemical bond still transduces biased displacement and mechanical work up to practically significant amounts. This "soft" approach possesses unique advantages over the conventional wisdom of rigidity-based transduction, and potentially leads to a unified mechanism for effective allosterylike transduction and relay of mechanical actions, information, control, and molecules from one position to another in molecular devices and motors. This study also identifies an entropy limit unique to the soft transduction, and thereby suggests a possibility of detecting higher efficiency for kinesin motor and mutants in future experiments.

Equilibrium and nonequilibrium dynamics of soft sphere fluids.

Science.gov (United States)

Ding, Yajun; Mittal, Jeetain

2015-07-14

We use computer simulations to test the freezing-point scaling relationship between equilibrium transport coefficients (self-diffusivity, viscosity) and thermodynamic parameters for soft sphere fluids. The fluid particles interact via the inverse-power potential (IPP), and the particle softness is changed by modifying the exponent of the distance-dependent potential term. In the case of IPP fluids, density and temperature are not independent variables and can be combined to obtain a coupling parameter to define the thermodynamic state of the system. We find that the rescaled coupling parameter, based on its value at the freezing point, can approximately collapse the diffusivity and viscosity data for IPP fluids over a wide range of particle softness. Even though the collapse is far from perfect, the freezing-point scaling relationship provides a convenient and effective way to compare the structure and dynamics of fluid systems with different particle softness. We further show that an alternate scaling relationship based on two-body excess entropy can provide an almost perfect collapse of the diffusivity and viscosity data below the freezing transition. Next, we perform nonequilibrium molecular dynamics simulations to calculate the shear-dependent viscosity and to identify the distinct role of particle softness in underlying structural changes associated with rheological properties. Qualitatively, we find a similar shear-thinning behavior for IPP fluids with different particle softness, though softer particles exhibit stronger shear-thinning tendency. By investigating the distance and angle-dependent pair correlation functions in these systems, we find different structural features in the case of IPP fluids with hard-sphere like and softer particle interactions. Interestingly, shear-thinning in hard-sphere like fluids is accompanied by enhanced translational order, whereas softer fluids exhibit loss of order with shear. Our results provide a systematic evaluation

Soft Neutrosophic Bi-LA-semigroup and Soft Neutrosophic N-LA-seigroup

Directory of Open Access Journals (Sweden)

Mumtaz Ali

2014-09-01

Full Text Available Soft set theory is a general mathematical tool for dealing with uncertain, fuzzy, not clearly defined objects. In this paper we introduced soft neutrosophic biLA-semigroup,soft neutosophic sub bi-LA-semigroup, soft neutrosophic N -LA-semigroup with the discuission of some of their characteristics. We also introduced a new type of soft neutrophic bi-LAsemigroup, the so called soft strong neutrosophic bi-LAsemigoup which is of pure neutrosophic character. This is also extend to soft neutrosophic strong N-LA-semigroup. We also given some of their properties of this newly born soft structure related to the strong part of neutrosophic theory.

On Some Nonclassical Algebraic Properties of Interval-Valued Fuzzy Soft Sets

Science.gov (United States)

2014-01-01

Interval-valued fuzzy soft sets realize a hybrid soft computing model in a general framework. Both Molodtsov's soft sets and interval-valued fuzzy sets can be seen as special cases of interval-valued fuzzy soft sets. In this study, we first compare four different types of interval-valued fuzzy soft subsets and reveal the relations among them. Then we concentrate on investigating some nonclassical algebraic properties of interval-valued fuzzy soft sets under the soft product operations. We show that some fundamental algebraic properties including the commutative and associative laws do not hold in the conventional sense, but hold in weaker forms characterized in terms of the relation =L. We obtain a number of algebraic inequalities of interval-valued fuzzy soft sets characterized by interval-valued fuzzy soft inclusions. We also establish the weak idempotent law and the weak absorptive law of interval-valued fuzzy soft sets using interval-valued fuzzy soft J-equal relations. It is revealed that the soft product operations ∧ and ∨ of interval-valued fuzzy soft sets do not always have similar algebraic properties. Moreover, we find that only distributive inequalities described by the interval-valued fuzzy soft L-inclusions hold for interval-valued fuzzy soft sets. PMID:25143964

On Some Nonclassical Algebraic Properties of Interval-Valued Fuzzy Soft Sets

Directory of Open Access Journals (Sweden)

Xiaoyan Liu

2014-01-01

Full Text Available Interval-valued fuzzy soft sets realize a hybrid soft computing model in a general framework. Both Molodtsov’s soft sets and interval-valued fuzzy sets can be seen as special cases of interval-valued fuzzy soft sets. In this study, we first compare four different types of interval-valued fuzzy soft subsets and reveal the relations among them. Then we concentrate on investigating some nonclassical algebraic properties of interval-valued fuzzy soft sets under the soft product operations. We show that some fundamental algebraic properties including the commutative and associative laws do not hold in the conventional sense, but hold in weaker forms characterized in terms of the relation =L. We obtain a number of algebraic inequalities of interval-valued fuzzy soft sets characterized by interval-valued fuzzy soft inclusions. We also establish the weak idempotent law and the weak absorptive law of interval-valued fuzzy soft sets using interval-valued fuzzy soft J-equal relations. It is revealed that the soft product operations ∧ and ∨ of interval-valued fuzzy soft sets do not always have similar algebraic properties. Moreover, we find that only distributive inequalities described by the interval-valued fuzzy soft L-inclusions hold for interval-valued fuzzy soft sets.

On some nonclassical algebraic properties of interval-valued fuzzy soft sets.

Science.gov (United States)

Liu, Xiaoyan; Feng, Feng; Zhang, Hui

2014-01-01

Interval-valued fuzzy soft sets realize a hybrid soft computing model in a general framework. Both Molodtsov's soft sets and interval-valued fuzzy sets can be seen as special cases of interval-valued fuzzy soft sets. In this study, we first compare four different types of interval-valued fuzzy soft subsets and reveal the relations among them. Then we concentrate on investigating some nonclassical algebraic properties of interval-valued fuzzy soft sets under the soft product operations. We show that some fundamental algebraic properties including the commutative and associative laws do not hold in the conventional sense, but hold in weaker forms characterized in terms of the relation = L . We obtain a number of algebraic inequalities of interval-valued fuzzy soft sets characterized by interval-valued fuzzy soft inclusions. We also establish the weak idempotent law and the weak absorptive law of interval-valued fuzzy soft sets using interval-valued fuzzy soft J-equal relations. It is revealed that the soft product operations ∧ and ∨ of interval-valued fuzzy soft sets do not always have similar algebraic properties. Moreover, we find that only distributive inequalities described by the interval-valued fuzzy soft L-inclusions hold for interval-valued fuzzy soft sets.

Kinetic study of formation of sodalite from a kaolin waste of Jari river - PA, Brazil

International Nuclear Information System (INIS)

Silva, L.N. da; Paz, S.P.A. da; Angelica, R.S.; Neves, R.F.

2011-01-01

Zeolites are materials with a wide industrial application, which has motivated the development of a large number of scientific papers on this topic. This work presents a kinetic study of the formation process of sodalite produced from the reaction of the kaolin waste in the presence of sodium hydroxide solution (5M) performed at temperatures of 80, 100, 120 and 150 ° C. The process was conducted in batch, static, and autoclaves lined with Teflon, and monitoring the kinetics was performed by ex situ XRD analysis of the materials obtained in the time interval from 2 to 24 hours. The kinetic model that best describes this transformation is zero-order homogeneous reaction. Finally, we conclude that the technique of X-ray diffraction is a powerful tool to study the kinetics of phase transformation ex situ. (author)

Bone and soft tissue ischemia

International Nuclear Information System (INIS)

Berquist, T.H.; Brown, M.L.; Joyce, J.W.; Johnson, K.A.

1989-01-01

This paper discusses clinical features and imaging techniques for ischemic necrosis, a common problem in the foot, particularly in diabetics and patients with other vascular diseases. Necrosis of bone and soft tissues will be considered separately as the underlying etiology and imaging evaluation differ considerably

Atividade pozolânica dos resíduos do beneficiamento do caulim para uso em argamassas para alvenaria Pozolanic activity of kaolin processing residues for use in masonry mortars

Directory of Open Access Journals (Sweden)

Romualdo R. Menezes

2009-12-01

Full Text Available A indústria do beneficiamento do caulim gera enorme quantidade de resíduos, descartados indiscriminadamente no meio ambiente; assim, este trabalho tem por objetivo analisar a viabilidade técnica e a atividade pozolânica dos resíduos do beneficiamento do caulim para a produção de argamassas. Os resíduos foram caracterizados através da determinação de sua distribuição granulométrica e composição química, difração de raios X e análise térmica diferencial e gravimétrica; em seguida, determinou-se o índice de atividade pozolânica dos resíduos de caulim com a cal e o cimento Portland. Argamassas de cimento:cal:areia foram preparadas e o resíduo, na condição natural e após queima a 600 °C por 2 h, substituiu parcialmente o cimento nas proporções de 5, 10, 15 e 20% em massa. Corpos-de-prova foram moldados e determinada sua resistência a compressão simples. Conclui-se, com base nos resultados, que os resíduos são constituídos de caulinita, mica e quartzo e que a utilização do resíduo calcinado aumenta a resistência das argamassas após 28 dias de cura em até 150%.The kaolin processing industry generates large amounts of waste, which is indiscriminately dumped in open-air sites. This work evaluates the technical suitability and pozolanic activity of kaolin processing wastes for the production of mortars. The wastes were characterized by particle size distribution and chemical composition determination, X-ray diffraction and thermal differential and gravimetric analyses. The pozolanic activity index was determined using lime and Portland cement. Cement:lime:sand mortars were formulated and the kaolin wastes replaced cement by 5, 10, 15 and 20% on weight basis. The kaolin wastes were used in their natural condition and after thermal treatment at 600 °C for 2 h. Test specimens were produced and their compression strength determined. The results indicated that the waste consists of quartz, kaolinite and mica, and

Optical and visual performance of aspheric soft contact lenses.

Science.gov (United States)

Efron, Suzanne; Efron, Nathan; Morgan, Philip B

2008-03-01

This study was conducted to investigate whether aspheric design soft contact lenses reduce ocular aberrations and result in better visual acuity and subjective appreciation of clinical performance compared with spherical soft contact lenses. A unilateral, double-masked, randomized and controlled study was undertaken in which ocular aberrations and high and low contrast logMAR visual acuity were measured on myopic subjects who wore aspheric design (Biomedics 55 Evolution, CooperVision) and spherical design (Biomedics 55, CooperVision) soft contact lenses. Ten subjects who had about -2.00 D myopia wore -2.00 D lenses and 10 subjects who had about -5.00 D myopia wore -5.00 D lenses. Measurements were made under photopic and mesopic lighting conditions. Subjects were invited to grade comfort, vision in photopic and mesopic conditions, and overall impression with the two lens types on 100 unit visual analogue scales. There was no significant difference in high contrast or low contrast visual acuity between the two lens designs of either power under photopic or mesopic conditions. Both lens designs displayed lower levels of spherical aberration compared with the "no lens" condition under photopic and mesopic light levels (p designs. There were no statistically significant differences in subjective appreciation of clinical performance between lens designs or lens powers. At least with respect to the brand of lenses tested, the fitting of aspheric design soft contact lenses does not result in superior visual acuity, aberration control, or subjective appreciation compared with equivalent spherical design soft contact lenses.

Management of Potato Soft Rot by Gamma Irradiation

International Nuclear Information System (INIS)

Abd El-Ghany, H.; Moussa, Z.; Abd El-Rahman, A.F.; Salem, E.A.

2017-01-01

This investigation aims to apply a safe practice to minimize potato losses due to soft rot disease of tubers kept under ambient temperature. In this regard, gamma irradiation was used to extend keeping quality through its effect on soft rot bacteria. Eight bacterial isolates were recovered on Logan’s medium from kitchen kept tubers with symptoms of soft rot disease. Five isolates were found pathogenic and tentatively identified as Pectobacterium atrosepticum and Pectobacterium carotovorum sub sp. brasiliense on the basis of the usual bacteriological methods. A molecular method using 16SrDNA sequence analysis for verification of the identity of two isolates was made. The two bacterial isolates, Pectobacterium atrosepticum and Pectobacterium carotovorum sub sp. brasiliense, were irradiated by different doses of gamma rays. Complete inhibition occurred at doses 2.5 and 2.0 KGy for high densities (Approximately 4.0x10"9 CFU/ml) of P. atrosepticum and P. carotovorum sub sp. brasiliense, respectively. The D10 value of gamma irradiation was 0.24 KGy for P. atrosepticum and 0.20 KGy for P. carotovorum subsp. brasiliense. Irradiation of artificially infected tubers with soft rot bacteria using the two mentioned D10 doses for the two bacterial species increased the shelf life of tubers kept under ambient temperature. The internal chemical quality of tubers was shown to be improved by keeping the tubers under ambient temperature after irradiation by the two D10 doses 0.24 and 0.20 KGy

Soft, embodied, situated & connected: enriching interactions with soft wearbles

NARCIS (Netherlands)

Tomico Plasencia, O.; Wilde, D.

2016-01-01

Soft wearables include clothing and textile-based accessories that incorporate smart textiles and soft electronic interfaces to enable responsive and interactive experiences. When designed well, soft wearables leverage the cultural, sociological and material qualities of textiles, fashion and dress;

Multiple scattering wavelength dependent backscattering of kaolin dust in the IR: Measurements and theory

Science.gov (United States)

Ben-David, Avishai

1992-01-01

Knowing the optical properties of aerosol dust is important for designing electro-optical systems and for modeling the effect on propagation of light in the atmosphere. As CO2 lidar technology becomes more advanced and is used for multiwavelength measurements, information on the wavelength dependent backscattering of aerosol dust particles is required. The volume backscattering coefficient of aerosols in the IR is relatively small. Thus, only a few field measurements of backscattering, usually at only a few wavelengths, are reported in the literature. We present spectral field measurements of backscattering of kaolin dust in the 9-11 micron wavelength range. As the quantity of dust increases, multiple scattering contributes more to the measured backscattered signal. The measurements show the effect of the dust quantity of the spectral backscatter measurements. A simple analytical two stream radiative transfer model is applied to confirm the measurements and to give insight to the multiple scattering spectra of backscattering.

Soft electronics for soft robotics

Science.gov (United States)

Kramer, Rebecca K.

2015-05-01

As advanced as modern machines are, the building blocks have changed little since the industrial revolution, leading to rigid, bulky, and complex devices. Future machines will include electromechanical systems that are soft and elastically deformable, lending them to applications such as soft robotics, wearable/implantable devices, sensory skins, and energy storage and transport systems. One key step toward the realization of soft systems is the development of stretchable electronics that remain functional even when subject to high strains. Liquid-metal traces embedded in elastic polymers present a unique opportunity to retain the function of rigid metal conductors while leveraging the deformable properties of liquid-elastomer composites. However, in order to achieve the potential benefits of liquid-metal, scalable processing and manufacturing methods must be identified.

The use of soft robotics in cardiovascular therapy.

Science.gov (United States)

Wamala, Isaac; Roche, Ellen T; Pigula, Frank A

2017-10-01

Robots have been employed in cardiovascular therapy as surgical tools and for automation of hospital systems. Soft robots are a new kind of robot made of soft deformable materials, that are uniquely suited for biomedical applications because they are inherently less likely to injure body tissues and more likely to adapt to biological environments. Awareness of the soft robotic systems under development will help promote clinician involvement in their successful clinical translation. Areas covered: The most advanced soft robotic systems, across the size scale from nano to macro, that have shown the most promise for clinical application in cardiovascular therapy because they offer solutions where a clear therapeutic need still exists. We discuss nano and micro scale technology that could help improve targeted therapy for cardiac regeneration in ischemic heart disease, and soft robots for mechanical circulatory support. Additionally, we suggest where the gaps in the technology currently lie. Expert commentary: Soft robotic technology has now matured from the proof-of-concept phase to successful animal testing. With further refinement in materials and clinician guided application, they will be a useful complement for cardiovascular therapy.

Effect of temperature on volume change behaviour of statically compacted kaolin clay

Directory of Open Access Journals (Sweden)

Ileme Ogechi

2016-01-01

Full Text Available Several soils are subjected to high temperature due to the environment where they are located or activities around them. For instance, upper layer of soils in tropical regions, soils around geothermal structures, clay barriers around nuclear waste repository systems. Numerous studies have pointed out that high temperature affects the hydro-mechanical properties of soils. Notwithstanding already existing studies, the influence of temperature on soils is still a challenge, as most of these studies are soil specific and cannot be inferred as the behaviour of all soils. This paper presents an experimental study on the influence of temperature on the volume change behaviour of statically compacted kaolin clay. Compacted samples were tested at varying temperatures using a suction controlled oedometer cell. The influence of temperature on the magnitude of volumetric strain occurring during mechanical and thermal loading was investigated. The study showed that an increase in temperature increased the magnitude of volumetric strain of the soil on loading. Additionally, the results presented in the light of LC curve showed that an increase in temperature resulted in the contraction and a change in the position of the LC curve.

Fibre-Matrix Interaction in Soft Tissue

International Nuclear Information System (INIS)

Guo, Zaoyang

2010-01-01

Although the mechanical behaviour of soft tissue has been extensively studied, the interaction between the collagen fibres and the ground matrix has not been well understood and is therefore ignored by most constitutive models of soft tissue. In this paper, the human annulus fibrosus is used as an example and the potential fibre-matrix interaction is identified by careful investigation of the experimental results of biaxial and uniaxial testing of the human annulus fibrosus. First, the uniaxial testing result of the HAF along the axial direction is analysed and it is shown that the mechanical behaviour of the ground matrix can be well simulated by the incompressible neo-Hookean model when the collagen fibres are all under contraction. If the collagen fibres are stretched, the response of the ground matrix can still be described by the incompressible neo-Hookean model, but the effective stiffness of the matrix depends on the fibre stretch ratio. This stiffness can be more than 10 times larger than the one obtained with collagen fibres under contraction. This phenomenon can only be explained by the fibre-matrix interaction. Furthermore, we find that the physical interpretation of this interaction includes the inhomogeneity of the soft tissue and the fibre orientation dispersion. The dependence of the tangent stiffness of the matrix on the first invariant of the deformation tensor can also be explained by the fibre orientation dispersion. The significant effect of the fibre-matrix interaction strain energy on mechanical behaviour of the soft tissue is also illustrated by comparing some simulation results.

Effect of kaolin treatment temperature on mortar chloride permeability

Directory of Open Access Journals (Sweden)

Puertas, F.

2007-03-01

Full Text Available The present paper discusses the results of chloride resistance tests conducted on ordinary Portland cement (OPC mortars containing a Colombian kaolin pre-treated at temperatures of from 600 to 800 ºC. The resulting metakaolin (MK was added to OPC mortar mixes in proportions of 10 and 20% by cement weight. The mortars were compared for physical and chemical properties, including capillary absorption, chloride permeability and pore microstructure as assessed by mercury porosimetry. The best performance was recorded for the samples containing 20% of the material treated at 800 ºC.En el presente trabajo se incluyen los resultados de la resistencia a la penetración de cloruros de morteros de Cemento Portland Ordinario (OPC adicionados con un caolín colombiano sometido a tratamiento térmico en un rango de temperaturas entre 600 y 800 °C. Los productos del tratamiento térmico, metacaolín (MK, son incorporados en mezclas de morteros de OPC en proporciones del 10 y 20% en relación al peso del cemento. Se comparan sus características físico-químicas, entre las cuales se incluye la microestructura de poros evaluada por la técnica de porosimetría de mercurio, con la absorción capilar y la permeabilidad a cloruros. Se concluye que las muestras adicionadas con un 20% del material tratado térmicamente a 800 °C presentan el mejor desempeño en sus propiedades finales.

Exploiting the Dynamics of Soft Materials for Machine Learning.

Science.gov (United States)

Nakajima, Kohei; Hauser, Helmut; Li, Tao; Pfeifer, Rolf

2018-06-01

Soft materials are increasingly utilized for various purposes in many engineering applications. These materials have been shown to perform a number of functions that were previously difficult to implement using rigid materials. Here, we argue that the diverse dynamics generated by actuating soft materials can be effectively used for machine learning purposes. This is demonstrated using a soft silicone arm through a technique of multiplexing, which enables the rich transient dynamics of the soft materials to be fully exploited as a computational resource. The computational performance of the soft silicone arm is examined through two standard benchmark tasks. Results show that the soft arm compares well to or even outperforms conventional machine learning techniques under multiple conditions. We then demonstrate that this system can be used for the sensory time series prediction problem for the soft arm itself, which suggests its immediate applicability to a real-world machine learning problem. Our approach, on the one hand, represents a radical departure from traditional computational methods, whereas on the other hand, it fits nicely into a more general perspective of computation by way of exploiting the properties of physical materials in the real world.

Soft leptogenesis

International Nuclear Information System (INIS)

D'Ambrosio, Giancarlo; Giudice, Gian F.; Raidal, Martti

2003-01-01

We study 'soft leptogenesis', a new mechanism of leptogenesis which does not require flavour mixing among the right-handed neutrinos. Supersymmetry soft-breaking terms give a small mass splitting between the CP-even and CP-odd right-handed sneutrino states of a single generation and provide a CP-violating phase sufficient to generate a lepton asymmetry. The mechanism is successful if the lepton-violating soft bilinear coupling is unconventionally (but not unnaturally) small. The values of the right-handed neutrino masses predicted by soft leptogenesis can be low enough to evade the cosmological gravitino problem

Induction of strand breaks in DNA films by low energy electrons and soft X-ray under nitrous oxide atmosphere

Energy Technology Data Exchange (ETDEWEB)

Alizadeh, Elahe, E-mail: Elahe.Alizadeh@USherbrooke.ca [Groupe en science des radiations, Departement de medecine nucleaire et radiobiologie, Faculte de medecine et des sciences de la sante, Universite de Sherbrooke, Sherbrooke, J1H 5N4 (Canada); Sanche, Leon, E-mail: Leon.Sanche@USherbrooke.ca [Groupe en science des radiations, Departement de medecine nucleaire et radiobiologie, Faculte de medecine et des sciences de la sante, Universite de Sherbrooke, Sherbrooke, J1H 5N4 (Canada)

2012-01-15

Five-monolayer (5 ML) plasmid DNA films deposited on glass and tantalum substrates were exposed to Al K{sub {alpha}} X-rays of 1.5 keV under gaseous nitrous oxide (N{sub 2}O) at atmospheric pressure and temperature. Whereas the damage yields for DNA deposited on glass are due to soft X-rays, those arising from DNA on tantalum are due to both the interaction of low energy photoelectrons from the metal and X-rays. Then, the differences in the yields of damage on glass and tantalum substrates, essentially arises from interaction of essentially low-energy electrons (LEEs) with DNA molecules and the surrounding atmosphere. The G-values (i.e., the number of moles of product per Joule of energy absorbed) for DNA strand breaks induced by LEEs (G{sub LEE}) and the lower limit of G-values for soft X-ray photons (G{sub XL}) were calculated and the results compared to those from previous studies under atmospheric conditions and other ambient gases, such as N{sub 2} and O{sub 2}. Under N{sub 2}O, the G-values for loss of supercoiled DNA are 103{+-}15 nmol/J for X-rays, and 737{+-}110 nmol/J for LEEs. Compared to corresponding values in an O{sub 2} atmosphere, the effectiveness of X-rays to damage DNA in N{sub 2}O is less, but the G value for LEEs in N{sub 2}O is more than twice the corresponding value for an oxygenated environment. This result indicates a higher effectiveness for LEEs relative to N{sub 2} and O{sub 2} environments in causing SSB and DSB in an N{sub 2}O environment. Thus, the previously observed radiosensitization of cells by N{sub 2}O may not be only due to OH{sup {center_dot}} radicals but also to the reaction of LEE with N{sub 2}O molecules near DNA. The previous experiments with N{sub 2} and O{sub 2} and the present one demonstrate the possibility to investigate damage induced by LEEs to biomolecules under various types of surrounding atmospheres. - Highlights: > A completely different and new approach is applied to investigate the radiation chemistry of N

The mechanics of soft biological composites.

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Thao D. (Sandia National Laboratories, Livermore, CA); Grazier, John Mark; Boyce, Brad Lee; Jones, Reese E. (Sandia National Laboratories, Livermore, CA)

2007-10-01

Biological tissues are uniquely structured materials with technologically appealing properties. Soft tissues such as skin, are constructed from a composite of strong fibrils and fluid-like matrix components. This was the first coordinated experimental/modeling project at Sandia or in the open literature to consider the mechanics of micromechanically-based anisotropy and viscoelasticity of soft biological tissues. We have exploited and applied Sandia's expertise in experimentation and mechanics modeling to better elucidate the behavior of collagen fibril-reinforced soft tissues. The purpose of this project was to provide a detailed understanding of the deformation of ocular tissues, specifically the highly structured skin-like tissue in the cornea. This discovery improved our knowledge of soft/complex materials testing and modeling. It also provided insight into the way that cornea tissue is bio-engineered such that under physiologically-relevant conditions it has a unique set of properties which enhance functionality. These results also provide insight into how non-physiologic loading conditions, such as corrective surgeries, may push the cornea outside of its natural design window, resulting in unexpected non-linear responses. Furthermore, this project created a clearer understanding of the mechanics of soft tissues that could lead to bio-inspired materials, such as highly supple and impact resistant body armor, and improve our design of human-machine interfaces, such as micro-electrical-mechanical (MEMS) based prosthetics.

Soft Robotics.

Science.gov (United States)

Whitesides, George M

2018-04-09

This description of "soft robotics" is not intended to be a conventional review, in the sense of a comprehensive technical summary of a developing field. Rather, its objective is to describe soft robotics as a new field-one that offers opportunities to chemists and materials scientists who like to make "things" and to work with macroscopic objects that move and exert force. It will give one (personal) view of what soft actuators and robots are, and how this class of soft devices fits into the more highly developed field of conventional "hard" robotics. It will also suggest how and why soft robotics is more than simply a minor technical "tweak" on hard robotics and propose a unique role for chemistry, and materials science, in this field. Soft robotics is, at its core, intellectually and technologically different from hard robotics, both because it has different objectives and uses and because it relies on the properties of materials to assume many of the roles played by sensors, actuators, and controllers in hard robotics. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cationic polyelectrolyte induced separation of some inorganic contaminants and their mixture (zirconium silicate, kaolin, K-feldspar, zinc oxide) as well as of the paraffin oil from water.

Science.gov (United States)

Ghimici, Luminita

2016-03-15

The flocculation efficiency of a cationic polyelectrolyte with quaternary ammonium salt groups in the backbone, namely PCA5 was evaluated on zirconium silicate (kreutzonit), kaolin, K- feldspar and zinc oxide (ZnO) suspensions prepared either with each pollutant or with their mixture. The effect of several parameters such as settling time, polymer dose and the pollutant type on the separation efficacy was evaluated and followed by optical density and zeta potential measurements. Except for ZnO, the interactions between PCA5 and suspended particles led to low residual turbidity values (around 4% for kreutzonit, 5% for kaolin and 8% for K-feldspar) as well as to the reduction of flocs settling time (from 1200 min to 30 min and 120 min in case of kaolinit and K-feldspar, respectively), that meant a high efficiency in their separation. The negative value of the zeta potential and flocs size measurements, at the optimum polymer dose, point to contribution from charge patch mechanism for the particles flocculation. A good efficiency of PCA5 in separation of paraffin oil (a minimum residual turbidity of 9.8%) has been also found. Copyright © 2015 Elsevier Ltd. All rights reserved.

Synthesis of CdS nanorods in soft template under gamma-irradiation.

Science.gov (United States)

Zhao, Bing; Wang, Yanli; Zhang, Haijiao; Jiao, Zheng; Wang, Haobo; Ding, Guoji; Wu, Minghong

2009-02-01

CdS nano material which has a band gap of 2.42 eV at room temperature is a typical II-VII semiconductor having many commercial or potential applications, e.g., light-emitting diodes, solar cell and optoelectronic devices. In this paper, we use a new strategy to synthesize CdS nanorods. CdS nanorods were prepared in soft template under gamma-irradiation though the reaction of cadmium sulphide and thiacetamide (TAA). The formation process and characters of CdS nanorods was investigated in detail by transmission electron microscopy (TEM), electron diffraction (ED) pattern, X-ray powder diffraction (XRD), ultraviolet spectrophotometer (UV) and photoluminescence spectrophotometer (PL). In the experiment we proposed that the irradiation of gamma-ray accelerated the formation of S(2-) under acidic condition (pH = 3) and vinyl acetate (VAc) monomer formed pre-organized nano polymer tubules which were used as both templates and nanoreacters for the growth of CdS nanorods. In this process, we have obtained the CdS polycrystal nanorods with PVAc nano tubules and CdS single-crystal nanorods. The result of X-ray powder diffraction confirms that the crystal type of CdS nanorods is cubic F-43 m (216). The results from transmission electron microscopy and electron diffraction show that the concentrations of reactants and the dose rate of gamma-ray are key to produce appropriate CdS nanorods. Relatively low concentrations (Cd2+: 0.008-0.02 mol/L, Cd2+ : S(2-) = 1 : 2) of reactants and long time (1-2 d) of irradiation in low dose rate (6-14 Gy/min) are propitious to form CdS single-crystal nanorods with small diameter (less than 100 nm) and well length (2-5 microm). UV and PL characterizations show the sample have well optical properties.

Harmonic Differential Quadrature Analysis of Soft-Core Sandwich Panels under Locally Distributed Loads

Directory of Open Access Journals (Sweden)

Xinwei Wang

2016-11-01

Full Text Available Sandwich structures are widely used in practice and thus various engineering theories adopting simplifying assumptions are available. However, most engineering theories of beams, plates and shells cannot recover all stresses accurately through their constitutive equations. Therefore, the soft-core is directly modeled by two-dimensional (2D elasticity theory without any pre-assumption on the displacement field. The top and bottom faces act like the elastic supports on the top and bottom edges of the core. The differential equations of the 2D core are then solved by the harmonic differential quadrature method (HDQM. To circumvent the difficulties in dealing with the locally distributed load by point discrete methods such as the HDQM, a general and rigorous way is proposed to treat the locally distributed load. Detailed formulations are provided. The static behavior of sandwich panels under different locally distributed loads is investigated. For verification, results are compared with data obtained by ABAQUS with very fine meshes. A high degree of accuracy on both displacement and stress has been observed.

Soft restructuring process in metallurgical enterprises in Poland

Directory of Open Access Journals (Sweden)

B. Gajdzik

2015-10-01

Full Text Available This article presents the range and outcomes of soft restructuring in metallurgical enterprises in Poland. The term ‘soft restructuring’ applies to changes in metallurgical enterprises’ employment policy during the period of political transformation in Poland. Steelworks performance under the market economy conditions demanded introducing changes in staff resources. Changes referred both to the staff structure as well as employees’ skills and gradual engaging of the staff in building the steelworks’ competitive advantage.

SUPRA SOFT SEPARATION AXIOMS AND SUPRA IRRESOLUTENESS BASED ON SUPRA B-SOFT SETS

OpenAIRE

Abd El-latif, Alaa Mohamed; Hosny, Rodyna Ahmed

2016-01-01

This paper introduces supra soft b-separation axioms based on the supra b-open soft sets which are more general than supra open soft sets. We investigate the relationships between these supra soft separation axioms. Furthermore, with the help of examples it is established that the converse does not hold. We show that, a supra soft topological space (X; t;E) is supra soft b-T1-space, if xE is supra b-closed soft set in for each x 2 X. Also, we prove that xE is supra b-closed soft set for each ...

Thermal-mechanical deformation modelling of soft tissues for thermal ablation.

Science.gov (United States)

Li, Xin; Zhong, Yongmin; Jazar, Reza; Subic, Aleksandar

2014-01-01

Modeling of thermal-induced mechanical behaviors of soft tissues is of great importance for thermal ablation. This paper presents a method by integrating the heating process with thermal-induced mechanical deformations of soft tissues for simulation and analysis of the thermal ablation process. This method combines bio-heat transfer theories, constitutive elastic material law under thermal loads as well as non-rigid motion dynamics to predict and analyze thermal-mechanical deformations of soft tissues. The 3D governing equations of thermal-mechanical soft tissue deformation are discretized by using the finite difference scheme and are subsequently solved by numerical algorithms. Experimental results show that the proposed method can effectively predict the thermal-induced mechanical behaviors of soft tissues, and can be used for the thermal ablation therapy to effectively control the delivered heat energy for cancer treatment.

Soft lubrication

Science.gov (United States)

Skotheim, Jan; Mahadevan, Laksminarayanan

2004-11-01

We study the lubrication of fluid-immersed soft interfaces and show that elastic deformation couples tangential and normal forces and thus generates lift. We consider materials that deform easily, due to either geometry (e.g a shell) or constitutive properties (e.g. a gel or a rubber), so that the effects of pressure and temperature on the fluid properties may be neglected. Four different system geometries are considered: a rigid cylinder moving tangentially to a soft layer coating a rigid substrate; a soft cylinder moving tangentially to a rigid substrate; a cylindrical shell moving tangentially to a rigid substrate; and finally a journal bearing coated with a thin soft layer, which being a conforming contact allows us to gauge the influence of contact geometry. In addition, for the particular case of a soft layer coating a rigid substrate we consider both elastic and poroelastic material responses. Finally, we consider the role of contact geometry in the context of the journal bearing, a conforming contact. For all these cases we find the same generic behavior: there is an optimal combination of geometric and material parameters that maximizes the dimensionless normal force as a function of the softness.

Measurement of soft X-ray power from high-power Z-pinch plasma

International Nuclear Information System (INIS)

Wang Wensheng; Qiu Aici; Sun Fengrong; Luo Jianhui; Zhou Haisheng; He Duohui

2003-01-01

A Ni-film bolometer driven by the pulsed constant-voltage supply was developed for measuring soft X-ray energy under 1 keV generated from the Qiang-Guang-I, while the measuring system of the soft X-ray power was established with an X-ray diode detector. Results of the soft X-ray energy and power measurements were obtained at the experiment of Kr gas-puff high-power Z-pinch plasma

Effects of Cd and Ni toxicity to Ceratophyllum demersum under environmentally relevant conditions in soft and hard water including a German lake

Energy Technology Data Exchange (ETDEWEB)

Andresen, Elisa, E-mail: Elisa.Andresen@uni-konstanz.de [University of Konstanz, Department of Biology, D-78457 Konstanz (Germany); Opitz, Judith, E-mail: Daniela.Opitz@uni-konstanz.de [University of Konstanz, Department of Biology, D-78457 Konstanz (Germany); Thomas, George, E-mail: George.Thomas@uni-konstanz.de [University of Konstanz, Department of Biology, D-78457 Konstanz (Germany); Stärk, Hans-Joachim, E-mail: Ha-Jo.Staerk@ufz.de [UFZ – Helmholtz Centre for Environmental Research, Department of Analytical Chemistry, Permoserstr. 15, D-04318 Leipzig (Germany); Dienemann, Holger, E-mail: Holger.Dienemann@smul.sachsen.de [Saxon State Company for Environment and Agriculture, Business Domain 5 (Laboratory), Department 53, Bitterfelder Str. 25, D-04849 Bad Düben (Germany); Jenemann, Kerstin, E-mail: Kerstin.Jenemann@smul.sachsen.de [Sächsisches Landesamt für Umwelt, Landwirtschaft und Geologie, Abteilung Wasser, Boden, Wertstoffe, Zur Wetterwarte 11, D-01109 Dresden (Germany); Dickinson, Bryan C., E-mail: Bryan.Dickinson@gmail.com [Harvard University, Department of Chemistry and Chemical Biology, 12 Oxford Street, Cambridge, MA 02138 (United States); Küpper, Hendrik, E-mail: Hendrik.Kuepper@uni-konstanz.de [University of Konstanz, Department of Biology, D-78457 Konstanz (Germany); University of South Bohemia, Faculty of Biological Sciences and Institute of Physical Biology, Branišovská 31, CZ-370 05 České Budejovice (Czech Republic)

2013-10-15

Highlights: •Hardly any macrophytic growth occurred in an oligotrophic hard water lake in Germany. •All parameters were optimal, besides elevated, nanomolar concentrations of Ni and Cd. •We cultivated submerged macrophytes in real and simulated hard and soft lake water. •Nanomolar Cd and Ni inhibited the plants’ photosynthetic light reactions in soft water. •The inhibition was synergistic, i.e. stronger than the addition of Cd and Ni effects. -- Abstract: Even essential trace elements are phytotoxic over a certain threshold. In this study, we investigated whether heavy metal concentrations were responsible for the nearly complete lack of submerged macrophytes in an oligotrophic lake in Germany. We cultivated the rootless aquatic model plant Ceratophyllum demersum under environmentally relevant conditions like sinusoidal light and temperature cycles and a low plant biomass to water volume ratio. Experiments lasted for six weeks and were analysed by detailed measurements of photosynthetic biophysics, pigment content and hydrogen peroxide production. We established that individually non-toxic cadmium (3 nM) and slightly toxic nickel (300 nM) concentrations became highly toxic when applied together in soft water, severely inhibiting photosynthetic light reactions. Toxicity was further enhanced by phosphate limitation (75 nM) in soft water as present in many freshwater habitats. In the investigated lake, however, high water hardness limited the toxicity of these metal concentrations, thus the inhibition of macrophytic growth in the lake must have additional reasons. The results showed that synergistic heavy metal toxicity may change ecosystems in many more cases than estimated so far.

Effects of Cd and Ni toxicity to Ceratophyllum demersum under environmentally relevant conditions in soft and hard water including a German lake

International Nuclear Information System (INIS)

Andresen, Elisa; Opitz, Judith; Thomas, George; Stärk, Hans-Joachim; Dienemann, Holger; Jenemann, Kerstin; Dickinson, Bryan C.; Küpper, Hendrik

2013-01-01

Highlights: •Hardly any macrophytic growth occurred in an oligotrophic hard water lake in Germany. •All parameters were optimal, besides elevated, nanomolar concentrations of Ni and Cd. •We cultivated submerged macrophytes in real and simulated hard and soft lake water. •Nanomolar Cd and Ni inhibited the plants’ photosynthetic light reactions in soft water. •The inhibition was synergistic, i.e. stronger than the addition of Cd and Ni effects. -- Abstract: Even essential trace elements are phytotoxic over a certain threshold. In this study, we investigated whether heavy metal concentrations were responsible for the nearly complete lack of submerged macrophytes in an oligotrophic lake in Germany. We cultivated the rootless aquatic model plant Ceratophyllum demersum under environmentally relevant conditions like sinusoidal light and temperature cycles and a low plant biomass to water volume ratio. Experiments lasted for six weeks and were analysed by detailed measurements of photosynthetic biophysics, pigment content and hydrogen peroxide production. We established that individually non-toxic cadmium (3 nM) and slightly toxic nickel (300 nM) concentrations became highly toxic when applied together in soft water, severely inhibiting photosynthetic light reactions. Toxicity was further enhanced by phosphate limitation (75 nM) in soft water as present in many freshwater habitats. In the investigated lake, however, high water hardness limited the toxicity of these metal concentrations, thus the inhibition of macrophytic growth in the lake must have additional reasons. The results showed that synergistic heavy metal toxicity may change ecosystems in many more cases than estimated so far

The effects of sucralfate suspension and diphenhydramine syrup plus kaolin-pectin on radiotherapy-induced mucositis

International Nuclear Information System (INIS)

Barker, G.; Loftus, L.; Cuddy, P.; Barker, B.

1991-01-01

A prospective, double-blind study compared the effectiveness of sucralfate suspension with diphenhydramine syrup plus kaolin-pectin in reducing severity and pain of radiation-induced oropharyngeal mucositis. Fourteen patients who received at least 4600 cGy to the oral cavity used one of the mouth rinses four times a day, beginning at 1600 cGy. Data were collected on daily perceived pain and helpfulness of mouth rinse, weekly mucositis grade, weight change, and interruption of therapy. Analysis of data revealed no statistically significant differences between the two groups in any parameter. A retrospective review of 15 patients who had received at least 4600 cGy radiation to the oropharynx but had not used a daily mouth-coating rinse, was compared with the study group. Comparison of the two groups suggested that consistent daily oral hygiene and use of a mouth-coating agent will result in less pain and may reduce weight loss and interruption of radiation because of severe mucositis

The effects of sucralfate suspension and diphenhydramine syrup plus kaolin-pectin on radiotherapy-induced mucositis

Energy Technology Data Exchange (ETDEWEB)

Barker, G.; Loftus, L.; Cuddy, P.; Barker, B. (Univ. of Missouri, Kansas City (USA))

1991-03-01

A prospective, double-blind study compared the effectiveness of sucralfate suspension with diphenhydramine syrup plus kaolin-pectin in reducing severity and pain of radiation-induced oropharyngeal mucositis. Fourteen patients who received at least 4600 cGy to the oral cavity used one of the mouth rinses four times a day, beginning at 1600 cGy. Data were collected on daily perceived pain and helpfulness of mouth rinse, weekly mucositis grade, weight change, and interruption of therapy. Analysis of data revealed no statistically significant differences between the two groups in any parameter. A retrospective review of 15 patients who had received at least 4600 cGy radiation to the oropharynx but had not used a daily mouth-coating rinse, was compared with the study group. Comparison of the two groups suggested that consistent daily oral hygiene and use of a mouth-coating agent will result in less pain and may reduce weight loss and interruption of radiation because of severe mucositis.

Equilibrium, kinetic and thermodynamic studies of adsorption of Th(IV) from aqueous solution onto kaolin

International Nuclear Information System (INIS)

Hongxia Zhang; Zhiwei Niu; Zhi Liu; Zhaodong Wen; Weiping Li; Xiaoyun Wang; Wangsuo Wu

2015-01-01

The kinetics and thermodynamics of the adsorption of Th(IV) on the kaolin were studied by using batch method. In addition, the experimental data were studied by dynamic and thermodynamic models. The results showed that the adsorption capacity of the adsorbent increased with increasing temperature and solid liquid ratio, but decreased with increasing initial Th(IV) ion concentration, and the best fit was obtained for the pseudo-second-order kinetics model. The calculated activation energy for adsorption was about 45 kJ/mol, which indicated the adsorption process to be chemisorption. The adsorption isotherm data could be well described by the Langmuir as well as Dubinin-Radushkevich model. The mean free energy (E) of adsorption was calculated to be about 15 kJ/mol. The thermodynamic data calculated showed that the adsorption was spontaneous and enhanced at higher temperature. Considering kinetics and equilibrium studies, the adsorption on the sites was the rate-limiting step and that adsorption was mainly a chemisorption process through cation exchange. (author)

Soft Congruence Relations over Rings

Science.gov (United States)

Xin, Xiaolong; Li, Wenting

2014-01-01

Molodtsov introduced the concept of soft sets, which can be seen as a new mathematical tool for dealing with uncertainty. In this paper, we initiate the study of soft congruence relations by using the soft set theory. The notions of soft quotient rings, generalized soft ideals and generalized soft quotient rings, are introduced, and several related properties are investigated. Also, we obtain a one-to-one correspondence between soft congruence relations and idealistic soft rings and a one-to-one correspondence between soft congruence relations and soft ideals. In particular, the first, second, and third soft isomorphism theorems are established, respectively. PMID:24949493

Soft Tissue Sarcoma

Science.gov (United States)

... muscles, tendons, fat, and blood vessels. Soft tissue sarcoma is a cancer of these soft tissues. There ... have certain genetic diseases. Doctors diagnose soft tissue sarcomas with a biopsy. Treatments include surgery to remove ...

Design of a Soft Robot with Multiple Motion Patterns Using Soft Pneumatic Actuators

Science.gov (United States)

Miao, Yu; Dong, Wei; Du, Zhijiang

2017-11-01

Soft robots are made of soft materials and have good flexibility and infinite degrees of freedom in theory. These properties enable soft robots to work in narrow space and adapt to external environment. In this paper, a 2-DOF soft pneumatic actuator is introduced, with two chambers symmetrically distributed on both sides and a jamming cylinder along the axis. Fibers are used to constrain the expansion of the soft actuator. Experiments are carried out to test the performance of the soft actuator, including bending and elongation characteristics. A soft robot is designed and fabricated by connecting four soft pneumatic actuators to a 3D-printed board. The soft robotic system is then established. The pneumatic circuit is built by pumps and solenoid valves. The control system is based on the control board Arduino Mega 2560. Relay modules are used to control valves and pressure sensors are used to measure pressure in the pneumatic circuit. Experiments are conducted to test the performance of the proposed soft robot.

Fabrication of recyclable and durable superhydrophobic materials with wear/corrosion-resistance properties from kaolin and polyvinylchloride

Science.gov (United States)

Qu, Mengnan; Liu, Shanshan; He, Jinmei; Feng, Juan; Yao, Yali; Ma, Xuerui; Hou, Lingang; Liu, Xiangrong

2017-07-01

In this study, mechanically stable and recyclable superhydrophobic materials were prepared from polyvinylchloride (PVC) and kaolin nanoparticles modified by stearic acid using a simple and low-cost drop-coating. The obtained materials displayed liquid-repellent toward water and several other liquids of daily life (such as orange juice, coffee, milk, coca cola and ink). These superhydrophobic materials showed remarkable robustness against sandpaper abrasion, UV-irradiation and ultrasonication test, while retaining its superhydrophobicity even after 60 abrasion cycles loaded of 500 g with sandpaper, 7 days UV-irradiation or 120 min ultrasonication test. The excellent durability against complex conditions was attributed to the hierarchical structure and strong interfacial adhesion of the materials. More significantly, the materials used in the coating could be recycled and reconstructed without losing its superhydrophobicity. The current superhydrophobic materials tolerate rigorous environment, opening a new avenue to a variety of practical applications.

Mechanical properties of anorthite based ceramics prepared from kaolin DD2 and calcite

Energy Technology Data Exchange (ETDEWEB)

Harabi, A.; Zaiou, S.; Guechi, A.; Foughali, L.; Harabi, E.; Karboua, N.-E.; Zouai, S.; Mezahi, F.-Z.; Guerfa, F., E-mail: harabi52@gmail.com, E-mail: Zaiou_21@yahoo.fr, E-mail: guechia@yahoo.fr, E-mail: semouni84@gmail.com, E-mail: kanour17@yahoo.fr, E-mail: foughali_lazhar@yahoo.fr, E-mail: zouaisouheila@yahoo.fr, E-mail: mezahif@yahoo.fr [Ceramics Lab., Faculty of Exact Science, Physics Department, Mentouri University of Constantine (Algeria)

2017-07-15

Good quality ceramics costs a lot that has limited their use in developing countries. This work was devoted to prepare low-cost and good quality anorthite based ceramics. The proposed composition was 80 wt% kaolin (DD2 type) and 20 wt% calcium oxide (CaO). The choice of these raw materials was dictated by their natural abundance coupled with a modified milling system, as another interesting advantage. Previous studies have shown that a simple vibratory multidirectional milling system using bimodal distribution of highly resistant ceramic milling elements has been successfully applied for obtaining fine powders. The influence of the relatively lower sintering temperature, ranging from 800 to 1100 °C, on the porosity and the average pore size (APS) have been investigated. The APS and the porosity values of samples sintered at 950 °C were about 1 μm and 4%, respectively. The best Vickers microhardness and 3-point bending strength values for these sintered samples, using this proposed milling system, were 7.1 GPa and 203 MPa, respectively. Finally, the crystalline phase evolution during heat treatment was investigated by X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy techniques. (author)

Responsive polyelectrolyte hydrogels and soft matter micromanipulation

NARCIS (Netherlands)

Glazer, P.J.

2013-01-01

This dissertation describes experimental studies on the mechanisms underlying the dynamic response of polyelectrolyte hydrogels when submitted to an external electric potential. In addition, we explore the possibilities of miniaturization and manipulation of responsive gels and other soft matter

Soft Power: Political Use of A Scientific Concept

Directory of Open Access Journals (Sweden)

Maksim Vladimirovich Kharkevich

2014-01-01

Full Text Available The article discusses the use and transformation of the American scientific concept "soft power" in official Russian and US foreign policy rhetoric with the methodological help of Habermas' communicative action theory and its adoption to IR by T. Risse. In mainstream IR the proliferation of the "soft power" concept is viewed in terms of ideological competition among states. The author argues that it is better to view this process as a form of international political deliberations on new forms of power in world politics. The article shows that there's no communicative action of US and Russia based on their tentative discussion of the "soft power" concept. On of reasons might be the lack of interest of both states for the concept as an ideological basis for cooperative actions. For Russia soft power in its classical form might be used towards its near abroad and probably BIC states. In dealings with western states Russian soft power turns into lobbyism and propaganda which is strictly not soft power. US under Obama have basically refuted the concept, having changed it for analytically meaningless "smart power". The conclusion is that communicative action requires prior existence of commutative rationality. This type of rationality is evident among postmodern states - the EU member states - and apparently absent among modern states such as Russia and US.

Hard and soft acids and bases: structure and process.

Science.gov (United States)

Reed, James L

2012-07-05

Under investigation is the structure and process that gives rise to hard-soft behavior in simple anionic atomic bases. That for simple atomic bases the chemical hardness is expected to be the only extrinsic component of acid-base strength, has been substantiated in the current study. A thermochemically based operational scale of chemical hardness was used to identify the structure within anionic atomic bases that is responsible for chemical hardness. The base's responding electrons have been identified as the structure, and the relaxation that occurs during charge transfer has been identified as the process giving rise to hard-soft behavior. This is in contrast the commonly accepted explanations that attribute hard-soft behavior to varying degrees of electrostatic and covalent contributions to the acid-base interaction. The ability of the atomic ion's responding electrons to cause hard-soft behavior has been assessed by examining the correlation of the estimated relaxation energies of the responding electrons with the operational chemical hardness. It has been demonstrated that the responding electrons are able to give rise to hard-soft behavior in simple anionic bases.

Probing scalar effective field theories with the soft limits of scattering amplitudes

Energy Technology Data Exchange (ETDEWEB)

Padilla, Antonio [School of Physics and Astronomy, University of Nottingham,University Park, Nottingham, NG7 2RD United Kingdom (United Kingdom); Stefanyszyn, David [Van Swinderen Institute for Particle Physics and Gravity, University of Groningen,Nijenborgh 4, Groningen, 9747 AG The (Netherlands); Wilson, Toby [School of Physics and Astronomy, University of Nottingham,University Park, Nottingham, NG7 2RD United Kingdom (United Kingdom)

2017-04-04

We investigate the soft behaviour of scalar effective field theories (EFTs) when there is a number of distinct derivative power counting parameters, ρ{sub 1}<ρ{sub 2}<…<ρ{sub Q}. We clarify the notion of an enhanced soft limit and use these to extend the scope of on-shell recursion techniques for scalar EFTs. As an example, we perform a detailed study of theories with two power counting parameters, ρ{sub 1}=1 and ρ{sub 2}=2, that include the shift symmetric generalised galileons. We demonstrate that the minimally enhanced soft limit uniquely picks out the Dirac-Born-Infeld (DBI) symmetry, including DBI galileons. For the exceptional soft limit we uniquely pick out the special galileon within the class of theories under investigation. We study the DBI galileon amplitudes more closely, verifying the validity of the recursion techniques in generating the six point amplitude, and explicitly demonstrating the invariance of all amplitudes under DBI galileon duality.

Soft Terms from Broken Symmetries

CERN Document Server

Buican, Matthew

2010-01-01

In theories of phyiscs beyond the Standard Model (SM), visible sector fields often carry quantum numbers under additional gauge symmetries. One could then imagine a scenario in which these extra gauge symmetries play a role in transmitting supersymmetry breaking from a hidden sector to the Supersymmetric Standard Model (SSM). In this paper we present a general formalism for studying the resulting hidden sectors and calculating the corresponding gauge mediated soft parameters. We find that a large class of generic models features a leading universal contribution to the soft scalar masses that only depends on the scale of Higgsing, even if the model is strongly coupled. As a by-product of our analysis, we elucidate some IR aspects of the correlation functions in General Gauge Mediation. We also discuss possible phenomenological applications.

Infrared Spectroscopic Study on Structural Change and Interfacial Interaction in Rubber Composites Filled with Silica-Kaolin Hybrid Fillers

Science.gov (United States)

Chen, Y.; Guan, J.; Hu, H.; Gao, H.; Zhang, L.

2016-07-01

A series of natural rubber/styrene butadiene rubber/polybutadiene rubber composites was prepared with nanometer silica and micron kaolin by a dry modification process, mechanical compounding, and mold vulcanization. Fourier transform infrared spectroscopy and a scanning electron microscope were used to investigate the structural changes and interfacial interactions in composites. The results showed that the "seesaw" structure was formed particularly with the incorporation of silica particles in the preparation process, which would be beneficial to the dispersibility of fillers in the rubber matrix. The kaolinite platelets were generally arranged in directional alignment. Kaolinite with smaller particle size and low-defect structure was more stable in preparation, but kaolinite with larger particle size and high defect structure tended to change the crystal structure. The composite prepared in this research exhibited excellent mechanical and thermal properties.

Rational Practices to Manage Boll Weevils Colonization and Population Growth on Family Farms in the Semiárido Region of Brazil.

Science.gov (United States)

Neves, Robério C S; Colares, Felipe; Torres, Jorge B; Santos, Roberta L; Bastos, Cristina S

2014-10-31

Because boll weevil, Anthonomus grandis Boh. develops partially protected inside cotton fruiting structures, once they become established in a field, they are difficult to control, even with nearly continuous insecticide spray. During two cotton-growing seasons in the Semiárido region of Pernambuco State, Brazil, we tested the use of kaolin sprays to disrupt plant colonization through visual cue interference, combined with removal of fallen fruiting bodies to restrain boll weevil population growth after colonization. Kaolin spray under non-choice trials resulted in 2.2×, 4.4×, and 8.6× fewer weevils, oviposition and feeding punctures on kaolin-treated plants, respectively, despite demonstrating no statistical differences for colonization and population growth. Early season sprays in 2010 occurred during a period of rainfall, and hence, under our fixed spraying schedule no significant differences in boll weevil colonization were detected. In 2011, when kaolin sprays were not washed out by rain, delayed boll weevil colonization and reduction on attacked fruiting bodies were observed in eight out of 12 evaluations, and kaolin-treated plots had 2.7× fewer damaged fruiting bodies compared to untreated plots. Adoption of simple measures such as removal of fallen fruiting bodies and prompt reapplication of kaolin sprays after rainfall show promise in reducing boll weevil infestation.

Model calibration for a soft elastomeric capacitor sensor considering slippage under fatigue cracks

Science.gov (United States)

Kong, Xiangxiong; Li, Jian; Bennett, Caroline; Collins, William; Laflamme, Simon

2016-04-01

A newly-developed soft elastomeric capacitor (SEC) strain sensor has shown promise in fatigue crack monitoring. The SECs exhibit high levels of ductility and hence do not break under excessive strain when the substrate cracks due to slippage or de-bonding between the sensor and epoxy. The actual strain experienced by a SEC depends on the amount of slippage, which is difficult to simulate numerically, making it challenging to accurately predict the response of a SEC near a crack. In this paper, a two-step approach is proposed to simulate the capacitance response of a SEC. First, a finite element (FE) model of a steel compact tension specimen was analyzed under cyclic loading while the cracking process was simulated based on an element removal technique. Second, a rectangular boundary was defined near the crack region. The SEC outside the boundary was assumed to have perfect bond with the specimen, while that inside the boundary was assumed to deform freely due to slippage. A second FE model was then established to simulate the response of the SEC within the boundary subject to displacements at the boundary from the first FE model. The total simulated capacitance was computed from the model results by combining the computed capacitance inside and outside the boundary. The performance of the simulation incorporating slippage was evaluated by comparing the model results with the experimental data from the test performed on a compact tension specimen. The FE model considering slippage showed results that matched the experimental findings more closely than the FE model that did not consider slippage.

SolarSoft Web Services

Science.gov (United States)

Freeland, S.; Hurlburt, N.

2005-12-01

The SolarSoft system (SSW) is a set of integrated software libraries, databases, and system utilities which provide a common programming and data analysis environment for solar physics. The system includes contributions from a large community base, representing the efforts of many NASA PI team MO&DA teams,spanning many years and multiple NASA and international orbital and ground based missions. The SSW general use libraries include Many hundreds of utilities which are instrument and mission independent. A large subset are also SOLAR independent, such as time conversions, digital detector cleanup, time series analysis, mathematics, image display, WWW server communications and the like. PI teams may draw on these general purpose libraries for analysis and application development while concentrating efforts on instrument specific calibration issues rather than reinvention of general use software. By the same token, PI teams are encouraged to contribute new applications or enhancements to existing utilities which may have more general interest. Recent areas of intense evolution include space weather applications, automated distributed data access and analysis, interfaces with the ongoing Virtual Solar Observatory efforts, and externalization of SolarSoft power through Web Services. We will discuss the current status of SSW web services and demonstrate how this facilitates accessing the underlying power of SolarSoft in more abstract terms. In this context, we will describe the use of SSW services within the Collaborative Sun Earth Connector environment.

Soft matter physics

CERN Document Server

Doi, Masao

2013-01-01

Soft matter (polymers, colloids, surfactants and liquid crystals) are an important class of materials in modern technology. They also form the basis of many future technologies, for example in medical and environmental applications. Soft matter shows complex behaviour between fluids and solids, and used to be a synonym of complex materials. Due to the developments of the past two decades, soft condensed matter can now be discussed on the same sound physical basis as solid condensedmatter. The purpose of this book is to provide an overview of soft matter for undergraduate and graduate students

Continued Development of a Soft Gamma-Ray Concentrator

Science.gov (United States)

Bloser, Peter

We propose to continue our development of a concept for a soft gamma-ray (E > 100 keV) concentrator using thin-film multilayer structures. Alternating layers of low- and high-density materials will channel soft gamma-ray photons via total external reflection. A suitable arrangement of bent structures will then concentrate the incident radiation to a point. Gamma-ray optics made in this way offer the potential for soft gamma-ray telescopes with focal lengths of less than 10 m, removing the need for formation flying spacecraft and opening the field up to balloon-borne instruments. Under previous APRA funding we have been investigating methods for efficiently producing such multilayer structures and modeling their performance. We now propose to pursue magnetron sputtering (MS) techniques to quickly produce structures with the required smoothness and thickness, to measure their channeling efficiency and compare with calculations, and to design a "lens" with optimized bandpass and throughput and predict its scientific performance. If successful, this work will confirm that this innovative optics concept is suitable for a balloon-born soft gamma-ray telescope with unprecedented sensitivity.

Methane reacts with heteropolyacids chemisorbed on silica to produce acetic acid under soft conditions

KAUST Repository

Sun, Miao

2013-01-16

Selective functionalization of methane at moderate temperature is of crucial economic, environmental, and scientific importance. Here, we report that methane reacts with heteropolyacids (HPAs) chemisorbed on silica to produce acetic acid under soft conditions. Specially, when chemisorbed on silica, H 4SiW12O40, H3PW12O 40, H4SiMo12O40, and H 3PMo12O40 activate the primary C-H bond of methane at room temperature and atmospheric pressure. With these systems, acetic acid is produced directly from methane, in a single step, in the absence of Pd and without adding CO. Extensive surface characterization by solid-state NMR spectroscopy, IR spectroscopy, cyclic voltammetry, and X-ray photoelectron spectroscopy suggests that C-H activation of methane is triggered by the protons in the HPA-silica interface with concerted reduction of the Keggin cage, leading to water formation and hydration of the interface. This is the simplest and mildest way reported to date to functionalize methane. © 2012 American Chemical Society.

Soft buckling actuators

Energy Technology Data Exchange (ETDEWEB)

Yang, Dian; Whitesides, George M.

2017-12-26

A soft actuator is described, including: a rotation center having a center of mass; a plurality of bucklable, elastic structural components each comprising a wall defining an axis along its longest dimension, the wall connected to the rotation center in a way that the axis is offset from the center of mass in a predetermined direction; and a plurality of cells each disposed between two adjacent bucklable, elastic structural components and configured for connection with a fluid inflation or deflation source; wherein upon the deflation of the cell, the bucklable, elastic structural components are configured to buckle in the predetermined direction. A soft actuating device including a plurality of the soft actuators and methods of actuation using the soft actuator or soft actuating device disclosed herein are also described.

Field testing for cosmic ray soft errors in semiconductor memories

International Nuclear Information System (INIS)

O'Gorman, T.J.; Ross, J.M.; Taber, A.H.; Ziegler, J.F.; Muhlfeld, H.P.; Montrose, C.J.; Curtis, H.W.; Walsh, J.L.

1996-01-01

This paper presents a review of experiments performed by IBM to investigate the causes of soft errors in semiconductor memory chips under field test conditions. The effects of alpha-particles and cosmic rays are separated by comparing multiple measurements of the soft-error rate (SER) of samples of memory chips deep underground and at various altitudes above the earth. The results of case studies on four different memory chips show that cosmic rays are an important source of the ionizing radiation that causes soft errors. The results of field testing are used to confirm the accuracy of the modeling and the accelerated testing of chips

Idiopathic Soft Tissue Calcification in an Extremity: A Case Report

Directory of Open Access Journals (Sweden)

Dinesh Dhar

2013-03-01

Full Text Available We report a case of a-15-days-old infant presenting with firm palpable thickening of the left leg soft tissues along with induration. Radiographs of the leg revealed generalized calcification of soft tissues. No obvious underlying cause could be identified for tissue calcification and hence termed as Idiopathic calcinois cutis. There are reports of this condition in Pediatric and Dermatology literature, but very few reports in orthopedic literature. The aim of this report is to highlight the pathogenesis, course and review of literature of this relatively uncommon condition which can easily be mistaken by Orthopedic or General Surgeons for infective bony of soft tissue infection.

Assessment of Soft Power Strategies: Towards an Aggregative Analytical Model for Country-Focused Case Study Research

Directory of Open Access Journals (Sweden)

Patalakh Artem

2016-10-01

Full Text Available The paper advances a realist analytical model for case studies of national soft power policies. First, it argues that for the purposes of realist analysis, a soft power policy must be considered as a rational strategy pursued under the conditions of competition. Furthermore, it emphasises the importance of taking into account the specificities of the recipient state as well as the fact that a soft power strategy is targeted at both its elite and its public. In addition, the article substantiates the necessity to draw a clear-cut distinction between soft power sources and instruments and shows possible shortcomings that research can have should this distinction fail to be made. Finally, the paper discusses the impact of a competitor’s presence on a soft power strategy and specifies the terms under which disregarding this impact may engender a wrong conclusion.

Extreme Mechanics in Soft Pneumatic Robots and Soft Microfluidic Electronics and Sensors

Science.gov (United States)

Majidi, Carmel

2012-02-01

In the near future, machines and robots will be completely soft, stretchable, impact resistance, and capable of adapting their shape and functionality to changes in mission and environment. Similar to biological tissue and soft-body organisms, these next-generation technologies will contain no rigid parts and instead be composed entirely of soft elastomers, gels, fluids, and other non-rigid matter. Using a combination of rapid prototyping tools, microfabrication methods, and emerging techniques in so-called ``soft lithography,'' scientists and engineers are currently introducing exciting new families of soft pneumatic robots, soft microfluidic sensors, and hyperelastic electronics that can be stretched to as much as 10x their natural length. Progress has been guided by an interdisciplinary collection of insights from chemistry, life sciences, robotics, microelectronics, and solid mechanics. In virtually every technology and application domain, mechanics and elasticity have a central role in governing functionality and design. Moreover, in contrast to conventional machines and electronics, soft pneumatic systems and microfluidics typically operate in the finite deformation regime, with materials stretching to several times their natural length. In this talk, I will review emerging paradigms in soft pneumatic robotics and soft microfluidic electronics and highlight modeling and design challenges that arise from the extreme mechanics of inflation, locomotion, sensor operation, and human interaction. I will also discuss perceived challenges and opportunities in a broad range of potential application, from medicine to wearable computing.

Elma Bahçelerinde Bazı Önemli Zararlılara Karşı Azadirachtin ve Kaolin Uygulamalarının Etkisi

Directory of Open Access Journals (Sweden)

Nazım KÜÇÜKBALLI

2018-02-01

Full Text Available Elma bahçelerinde ekonomik kayıplara neden olan birçok hastalık, zararlı ve yabancıot türü bulunmaktadır. Zararlılar içinde elma içkurdu, kırmızıörümcekler ve yaprakbitleri ana zararlılar arasında yer almaktadır. Elma üretiminin yoğun yapıldığı Isparta ilinde özellikle yağışlı geçen yıllarda yılda 20 kezden daha fazla ilaçlama yapıldığı bilinmektedir. Bu çalışmada söz konusu zararlılara karşı çevre ve yararlılara fazla etkisi olmadığı bilinen azadirachtin ve kaolinin etkisi 2015 yılında incelenmiştir. Denemeler Süleyman Demirel Üniversitesi, Ziraat Fakültesi bünyesinde bulunan 5 ve 2 dekarlık iki elma bahçesinde yürütülmüştür. Her bahçe dört parsele ayrılmış ve her bir parsele kaolin, azadirachtin (neem, karşılaştırma ilacı olarak chlorpyrifos-ethyl ve Kontrol parseline de su püskürtme şeklinde uygulanmıştır. Denemeler tesadüf blokları deneme desenine göre kurulmuş olup, her tekerrürde 8 ağaç olacak şekilde 6 tekerrürlü olarak düzenlenmiştir. Her hafta, her bir ağaçtan 40 yaprak örneği alınarak Tetranychus urticae, Pananychus ulmi, Aphis pomi ve Dysaphis plantaginea sayımları yapılmıştır. Elma içkurdu zararı ise hasat zamanında ağaç üzerinde ve yere düşen meyvelerde bulaşma oranına göre belirlenmiştir. Çalışma sonucunda yaprakbitine karşı en etkili Chlorpyrifos-ethyl bulunmuş, bunu kaolin ve neem izlemiştir. Preparatlar kırmızıörümceklere karşı benzer etki gösterirken elma içkurdu bulaşma oranları sırasıyla, kontrol parselinde %49.99, kaolin parselinde %42.27, neem parselinde %41.20 ve chlorpyrifos-ethyl parselinde %31.23 olmuştur.

A-Soft Separation Axioms in Soft Topological Space

Directory of Open Access Journals (Sweden)

Luay Abd –Al-Hani Al-Sweedi

2018-01-01

Full Text Available The important science tools in a different kinds and  specialties , that considered the basic mainstay of ( the set theory and because of  huge development in all life fields. This causes great problems , that need solution and parallel tools for those developments , so the scientis become responsible to work on the development of number theory and open new horizons , that a new science had appeared  which is  ( soft figures theory which is considered the important tool to solve most difficult problems or overcome them ,in these sciences and their specific life specialization, economy, medicine , geometry and others. Also the theory of soft numbers had entered in general topology in power full and active way. The last years a new science has appeared is (soft topological space.              The main idea of this research is to define the separation axioms in  (soft topological space  and practically in certain point , and to study the most important  properties and results of it .

Phase modification and dielectric properties of a cullet-paper ash-kaolin clay-based ceramic

Science.gov (United States)

Samah, K. A.; Sahar, M. R.; Yusop, M.; Omar, M. F.

2018-03-01

Novel ceramics from waste material made of ( x) paper ash-(80 - x) cullet-20 kaolin clay (10wt% ≤ x ≤ 30wt%) were successfully synthesized using a conventional solid-state reaction technique. Energy-dispersive X-ray analysis confirmed the presence of Si, Ca, Al, and Fe in the waste material for preparing these ceramics. The influence of the cullet content on the phase structures and the dielectric properties of these ceramics were systematically investigated. The impedance spectra were verified in the range from 1 Hz to 10 MHz at room temperature. The phase of the ceramics was found to primarily consist of wollastonite (CaSiO3), along with minor phases of γ-dicalcium silicate (Ca2SiO4) and quartz (SiO2). The sample with a cullet content of 55wt% possessed the optimum wollastonite structure and exhibited good dielectric properties. An increase of the cullet content beyond 55wt% resulted in a structural change from wollastonite to dicalcium silicate, a decrease in dielectric constant, and an increase in dielectric loss. All experimental results suggested that these novel ceramics from waste are applicable for electronic devices.

Hydrothermal synthesis of zeolite T from kaolin using two different structure-directing agents

Science.gov (United States)

Arshad, Sazmal E.; Lutfor Rahman, M.; Sarkar, Shaheen M.; Yusslee, Eddy F.; Patuwan, Siti Z.

2018-01-01

Zeolite T was synthesized from the molar chemical composition of 1SiO2:0.04Al2O3:0.26Na2O:0.09K2O:14H2O in the form of a homogenous milky solution in the presence of the two different structure-directing agents TMAOH and TEAOH respectively. Modification of the composition of silica was undertaken using metakaolin from calcined kaolin at 750 °C for 4 h, while the molar composition of each different SDA was variated from 0.05, 0.10, 0.15, 0.20 and 0.25. The homogenous mixture was left at room temperature for 24 h before undergoing hydrothermal synthesis at 100 °C for 168 h. The synthesized samples were filtered and aged at 120 °C for 2 h and each sample was calcined at high temperatures (545 °C for TMAOH and 520 °C for TEAOH) for template removal before characterization using XRD and SEM. Crystallization of the zeolite T in its major form only took place at a molar ratio of 0.10 of TMAOH, while TEAOH showed the species evolution of zeolite T into zeolite L and W for other molar ratios.

Soft Robotics: Biological Inspiration, State of the Art, and Future Research

Directory of Open Access Journals (Sweden)

Deepak Trivedi

2008-01-01

Full Text Available Traditional robots have rigid underlying structures that limit their ability to interact with their environment. For example, conventional robot manipulators have rigid links and can manipulate objects using only their specialised end effectors. These robots often encounter difficulties operating in unstructured and highly congested environments. A variety of animals and plants exhibit complex movement with soft structures devoid of rigid components. Muscular hydrostats (e.g. octopus arms and elephant trunks are almost entirely composed of muscle and connective tissue and plant cells can change shape when pressurised by osmosis. Researchers have been inspired by biology to design and build soft robots. With a soft structure and redundant degrees of freedom, these robots can be used for delicate tasks in cluttered and/or unstructured environments. This paper discusses the novel capabilities of soft robots, describes examples from nature that provide biological inspiration, surveys the state of the art and outlines existing challenges in soft robot design, modelling, fabrication and control.

Rational Practices to Manage Boll Weevils Colonization and Population Growth on Family Farms in the Semiárido Region of Brazil

Directory of Open Access Journals (Sweden)

Robério C. S. Neves

2014-10-01

Full Text Available Because boll weevil, Anthonomus grandis Boh. develops partially protected inside cotton fruiting structures, once they become established in a field, they are difficult to control, even with nearly continuous insecticide spray. During two cotton-growing seasons in the Semiárido region of Pernambuco State, Brazil, we tested the use of kaolin sprays to disrupt plant colonization through visual cue interference, combined with removal of fallen fruiting bodies to restrain boll weevil population growth after colonization. Kaolin spray under non-choice trials resulted in 2.2×, 4.4×, and 8.6× fewer weevils, oviposition and feeding punctures on kaolin-treated plants, respectively, despite demonstrating no statistical differences for colonization and population growth. Early season sprays in 2010 occurred during a period of rainfall, and hence, under our fixed spraying schedule no significant differences in boll weevil colonization were detected. In 2011, when kaolin sprays were not washed out by rain, delayed boll weevil colonization and reduction on attacked fruiting bodies were observed in eight out of 12 evaluations, and kaolin-treated plots had 2.7× fewer damaged fruiting bodies compared to untreated plots. Adoption of simple measures such as removal of fallen fruiting bodies and prompt reapplication of kaolin sprays after rainfall show promise in reducing boll weevil infestation.

Observation of elastic topological states in soft materials.

Science.gov (United States)

Li, Shuaifeng; Zhao, Degang; Niu, Hao; Zhu, Xuefeng; Zang, Jianfeng

2018-04-10

Topological elastic metamaterials offer insight into classic motion law and open up opportunities in quantum and classic information processing. Theoretical modeling and numerical simulation of elastic topological states have been reported, whereas the experimental observation remains relatively unexplored. Here we present an experimental observation and numerical simulation of tunable topological states in soft elastic metamaterials. The on-demand reversible switch in topological phase has been achieved by changing filling ratio, tension, and/or compression of the elastic metamaterials. By combining two elastic metamaterials with distinct topological invariants, we further demonstrate the formation and dynamic tunability of topological interface states by mechanical deformation, and the manipulation of elastic wave propagation. Moreover, we provide a topological phase diagram of elastic metamaterials under deformation. Our approach to dynamically control interface states in soft materials paves the way to various phononic systems involving thermal management and soft robotics requiring better use of energy.

On soft singularities at three loops and beyond

CERN Document Server

Dixon, Lance J; Magnea, Lorenzo

2010-01-01

We report on further progress in understanding soft singularities of massless gauge theory scattering amplitudes. Recently, a set of equations was derived based on Sudakov factorization, constraining the soft anomalous dimension matrix of multi-leg scattering amplitudes to any loop order, and relating it to the cusp anomalous dimension. The minimal solution to these equations was shown to be a sum over color dipoles. Here we explore potential contributions to the soft anomalous dimension that go beyond the sum-over-dipoles formula. Such contributions are constrained by factorization and invariance under rescaling of parton momenta to be functions of conformally invariant cross ratios. Therefore, they must correlate the color and kinematic degrees of freedom of at least four hard partons, corresponding to gluon webs that connect four eikonal lines, which first appear at three loops. We analyze potential contributions, combining all available constraints, including Bose symmetry, the expected degree of transcen...

Nanostructured Soft Matter Experiment, Theory, Simulation and Perspectives

CERN Document Server

Zvelindovsky, Andrei V

2007-01-01

This book provides an interdisciplinary overview of a new and broad class of materials under the unifying name Nanostructured Soft Matter. It covers materials ranging from short amphiphilic molecules to block copolymers, proteins, colloids and their composites, microemulsions and bio-inspired systems such as vesicles. The book considers several fundamental questions, including: how self-assembly of various soft materials with internal structure at the nanoscale can be understood, controlled and in future used in the newly emerging field of soft nanotechnology. The book offers readers a view on the subject from different perspectives, combining modern experimental approaches from physical chemistry and physics with various theoretical techniques from physics, mathematics and the most advanced computer modelling. It is the first book of this sort in the field. All chapters are written by leading international experts, bringing together experience from Canada, Germany, Great Britain, Japan, the Netherlands, Russ...

Design and development of the roadbed construction on the soft soils

Directory of Open Access Journals (Sweden)

Yushkov Boris Semenovich

2014-12-01

Full Text Available Now the considerable part of territories is presented by soft soils. Construction of highways under difficult conditions, in places of the soft heaving soil distribution having an excessive moistening, low bearing capability, high compressibility and other unfavorable properties, significantly complicates and raises the price of road construction. Improvement of technology of highway construction serves as a solution of problem. In this article the authors propose the design of a roadbed on the soft clay soil, strengthened by a spatial geoweb. The experimental studies of four designs were conducted: the first one is research of the roadbed — soft clay soil mutual interaction; the second one is research of work of the geotextile material laid in the base of roadbed with the soft clay soil; the third one is research of work of the spatial geoweb laid in the base of roadbed with the soft clay soil; the fourth one is research of joint action of a spatial geoweb and the geotextile material laid in the base of a roadbed with soft clay soil. Based on the results of the carried-out laboratory tests it has been revealed that the design with strengthening by a spatial geoweb and geotextile material has a rational one of the roadbed.

Mappings on Neutrosophic Soft Classes

Directory of Open Access Journals (Sweden)

Shawkat Alkhazaleh

2014-03-01

Full Text Available In 1995 Smarandache introduced the concept of neutrosophic set which is a mathematical tool for handling problems involving imprecise, indeterminacy and inconsistent data. In 2013 Maji introduced the concept of neutrosophic soft set theory as a general mathematical tool for dealing with uncertainty. In this paper we define the notion of a mapping on classes where the neutrosophic soft classes are collections of neutrosophic soft set. We also define and study the properties of neutrosophic soft images and neutrosophic soft inverse images of neutrosophic soft sets.

SoftLab: A Soft-Computing Software for Experimental Research with Commercialization Aspects

Science.gov (United States)

Akbarzadeh-T, M.-R.; Shaikh, T. S.; Ren, J.; Hubbell, Rob; Kumbla, K. K.; Jamshidi, M

1998-01-01

SoftLab is a software environment for research and development in intelligent modeling/control using soft-computing paradigms such as fuzzy logic, neural networks, genetic algorithms, and genetic programs. SoftLab addresses the inadequacies of the existing soft-computing software by supporting comprehensive multidisciplinary functionalities from management tools to engineering systems. Furthermore, the built-in features help the user process/analyze information more efficiently by a friendly yet powerful interface, and will allow the user to specify user-specific processing modules, hence adding to the standard configuration of the software environment.

Preparation and solar-light photocatalytic activity of TiO2 composites: TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite

Science.gov (United States)

Li, Y.; Li, S. G.; Wang, J.; Li, Y.; Ma, C. H.; Zhang, L.

2014-12-01

Three TiO2 loaded composites, TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite, were prepared in order to improve the solar-light photocatalytic activity of TiO2. The results showed that the photocatalytic activity could obviously be enhanced by loading appropriate amount of inorganic mineral materials. Meanwhile, TiO2 content, heat-treatment temperature and heat-treatment time on the photocatalytic activity were reviewed. Otherwise, the effect of solar light irradiation time and dye concentration on the photocatalytic degradation of Acid Red B was investigated. Furthermore, the degradation mechanism and adsorption process were also discussed.

Production optimization of probiotic soft cheese made from goat's and cow's milk

Directory of Open Access Journals (Sweden)

Ida Drgalić

2006-07-01

Full Text Available The aim of this study was to determine optimal rennet share and fat content in milk for probiotic soft cheeseproduction made from goat's and cow's milk using DVS mixed probiotic culture ABT-4 (Lactobacillus acidophilus, Bifidobacterium spp. and Streptococcus thermophilus, with desirable sensory properties, which will be acceptable by consumers. The best sensory scores had samples of probiotic soft cheese produced in laboratory conditions from milk with 1% of milk fat, pasteurized at 65°C/30 min., fermented at 38°C with 2% culture. To achieve characteristic consistency of traditional soft cheese, 0.01% of rennet was added to goat's milk. Probiotic soft cheese made from cow's and goat's milk, produced under optimal conditions, were 100% acceptable by the tested consumers.

Soft mobile robots driven by foldable dielectric elastomer actuators

Energy Technology Data Exchange (ETDEWEB)

Sun, Wenjie; Liu, Fan; Ma, Ziqi; Li, Chenghai; Zhou, Jinxiong, E-mail: jxzhouxx@mail.xjtu.edu.cn [State Key Laboratory for Strength and Vibration of Mechanical Structures and School of Aerospace, Xi' an Jiaotong University, Xi' an 710049 (China)

2016-08-28

A cantilever beam with elastic hinge pulled antagonistically by two dielectric elastomer (DE) membranes in tension forms a foldable actuator if one DE membrane is subject to a voltage and releases part of tension. Simply placing parallel rigid bars on the prestressed DE membranes results in enhanced actuators working in a pure shear state. We report design, analysis, fabrication, and experiment of soft mobile robots that are moved by such foldable DE actuators. We describe systematic measurement of the foldable actuators and perform theoretical analysis of such actuators based on minimization of total energy, and a good agreement is achieved between model prediction and measurement. We develop two versions of prototypes of soft mobile robots driven either by two sets of DE membranes or one DE membrane and elastic springs. We demonstrate locomotion of these soft mobile robots and highlight several key design parameters that influence locomotion of the robots. A 45 g soft robot driven by a cyclic triangle voltage with amplitude 7.4 kV demonstrates maximal stroke 160 mm or maximal rolling velocity 42 mm/s. The underlying mechanics and physics of foldable DE actuators can be leveraged to develop other soft machines for various applications.

Synthesis, characterization and application of nanozeolite NaX from Vietnamese kaolin

International Nuclear Information System (INIS)

Ngoc, Don Ta; Pham, Thanh Huyen; Hong Nguyen, Khanh Dieu

2013-01-01

This paper presents the results of synthesis of nanozeolite NaX from Vietnamese kaolin. Influence factors on the control of crystal sizes and application of synthesized materials as adsorbent for organic compound are discussed. The results show that there are several factors that influence the synthesis. When water content in gel increases, crystal size of NaX increases sharply. The increase of alkaline and silica contents increases the crystallinity and decreases the particle size of nano NaX, and the particle size reaches the minimum at Na 2 O/Al 2 O 3 = 5.0 and SiO 2 /Al 2 O 3 = 4.0. Crystal sizes formed at low crystallizing temperature are smaller than those formed at higher temperature. Ageing time and crystallizing time strongly influence the crystallinity and crystal size, which is related to the number of crystal seeds formed during ageing period, the growth of seed and the partial solubility of crystal at maximum formation. Nano NaX was characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) adsorption, Fourier transform infrared (FTIR) and simultaneous thermogravimetry–differential scanning calorimetry (TG/DSC). At optimized synthesis conditions, nano NaX has surface area of 573 m 2 g −1 with external surface area of 92 m 2 g −1 , pore size distribution at 0.81 and 10.8 nm, average crystal size of 25 nm and thermal stability up to 789 °C. This material can adsorb cumene rapidly with high adsorption capacity and stability. (paper)

Size Distribution, Chemical Composition and Optical Properties of Atmospheric Dust in Israel: A Comparison of Urban and Desert Aerosols under Clear and Dusty Conditions.

Science.gov (United States)

1980-02-01

counter (Royco 220). The instrument was calibrated with dry Latex particles of known sizes which were dispersed from a liquid suspension by the use of an...such spectra it is clear that samples from both sites contain significant amounts of gypsum, clay minerals, notably kaolin and montmorillonite clays...using a wavelength dispersive micro- probe. A comparison between aerosols from the Negev desert and Tel Aviv (under easterly flow) was conducted

Soft Budgets And Highway Franchising

OpenAIRE

Eduardo Engel; Ronald Fischer; Alexander Galetovic

2004-01-01

Latin American governments progressively substituted build–operate–and–transfer (BOT) contracts for government–provided highways during the nineties. Because under BOT a private franchise holder finances and operates the road in exchange for tolls, it is often claimed that BOT represents a privatization of highways. We argue that, as currently applied, the BOT model is an imperfect and incomplete privatization, because the franchise holders’ budget constraint has been soft, with losses being ...

Differential diagnosis between benign and malignant soft tissue tumors utilizing ultrasound parameters.

Science.gov (United States)

Morii, Takeshi; Kishino, Tomonori; Shimamori, Naoko; Motohashi, Mitsue; Ohnishi, Hiroaki; Honya, Keita; Aoyagi, Takayuki; Tajima, Takashi; Ichimura, Shoichi

2018-01-01

Preoperative discrimination between benign and malignant soft tissue tumors is critical for the prevention of excess application of magnetic resonance imaging and biopsy as well as unplanned resection. Although ultrasound, including power Doppler imaging, is an easy, noninvasive, and cost-effective modality for screening soft tissue tumors, few studies have investigated reliable discrimination between benign and malignant soft tissue tumors. To establish a modality for discrimination between benign and malignant soft tissue tumors using ultrasound, we extracted the significant risk factors for malignancy based on ultrasound information from 40 malignant and 56 benign pathologically diagnosed soft tissue tumors and established a scoring system based on these risk factors. The maximum size, tumor margin, and vascularity evaluated using ultrasound were extracted as significant risk factors. Using the odds ratio from a multivariate regression model, a scoring system was established. Receiver operating characteristic analyses revealed a high area under the curve value (0.85), confirming the accuracy of the scoring system. Ultrasound is a useful modality for establishing the differential diagnosis between benign and malignant soft tissue tumors.

Utilization of synchrotron radiation in analytical chemistry. Soft X-ray emission and absorption spectroscopy

International Nuclear Information System (INIS)

Muramatsu, Yasuji

2015-01-01

Synchrotron soft X-ray spectroscopy includes three major types of spectroscopy such as X-ray absorption spectroscopy (XAS), X-ray emission spectroscopy (XES), and X-ray photoelectron spectroscopy (XPS). This paper takes up XAS and XES of soft X-rays, and briefly describes the principle. XAS is roughly classified into XANES (X-ray absorption near-edge structure) and EXAFS (extended X-ray absorption fine structure), and XANES is mainly used in the analysis based on XAS of soft X-rays. As the examples of the latest soft X-ray analyses, the following are introduced: (1) bandgap of boron implantation diamond and the local structure of boron, (2) catalytic sites in solid fuel cell carbon electrode, and (3) soft X-ray analysis under atmospheric pressure. (A.O.)

Diagnosis of soft faults in analog integrated circuits based on fractional correlation

International Nuclear Information System (INIS)

Deng Yong; Shi Yibing; Zhang Wei

2012-01-01

Aiming at the problem of diagnosing soft faults in analog integrated circuits, an approach based on fractional correlation is proposed. First, the Volterra series of the circuit under test (CUT) decomposed by the fractional wavelet packet are used to calculate the fractional correlation functions. Then, the calculated fractional correlation functions are used to form the fault signatures of the CUT. By comparing the fault signatures, the different soft faulty conditions of the CUT are identified and the faults are located. Simulations of benchmark circuits illustrate the proposed method and validate its effectiveness in diagnosing soft faults in analog integrated circuits. (semiconductor integrated circuits)

Soft Neutrosophic Loops and Their Generalization

Directory of Open Access Journals (Sweden)

Mumtaz Ali

2014-06-01

Full Text Available Soft set theory is a general mathematical tool for dealing with uncertain, fuzzy, not clearly defined objects. In this paper we introduced soft neutrosophic loop,soft neutosophic biloop, soft neutrosophic N -loop with the discuission of some of their characteristics. We also introduced a new type of soft neutrophic loop, the so called soft strong neutrosophic loop which is of pure neutrosophic character. This notion also found in all the other corresponding notions of soft neutrosophic thoery. We also given some of their properties of this newly born soft structure related to the strong part of neutrosophic theory.

Evolution of real contact area under shear and the value of static friction of soft materials.

Science.gov (United States)

Sahli, R; Pallares, G; Ducottet, C; Ben Ali, I E; Al Akhrass, S; Guibert, M; Scheibert, J

2018-01-16

The frictional properties of a rough contact interface are controlled by its area of real contact, the dynamical variations of which underlie our modern understanding of the ubiquitous rate-and-state friction law. In particular, the real contact area is proportional to the normal load, slowly increases at rest through aging, and drops at slip inception. Here, through direct measurements on various contacts involving elastomers or human fingertips, we show that the real contact area also decreases under shear, with reductions as large as 30[Formula: see text], starting well before macroscopic sliding. All data are captured by a single reduction law enabling excellent predictions of the static friction force. In elastomers, the area-reduction rate of individual contacts obeys a scaling law valid from micrometer-sized junctions in rough contacts to millimeter-sized smooth sphere/plane contacts. For the class of soft materials used here, our results should motivate first-order improvements of current contact mechanics models and prompt reinterpretation of the rate-and-state parameters.

Soft-Material Robotics

OpenAIRE

Wang, L; Nurzaman, SG; Iida, Fumiya

2017-01-01

There has been a boost of research activities in robotics using soft materials in the past ten years. It is expected that the use and control of soft materials can help realize robotic systems that are safer, cheaper, and more adaptable than the level that the conventional rigid-material robots can achieve. Contrary to a number of existing review and position papers on soft-material robotics, which mostly present case studies and/or discuss trends and challenges, the review focuses on the fun...

X-ray shielding behaviour of kaolin derived mullite-barites ceramic

Science.gov (United States)

Ripin, A.; Mohamed, F.; Choo, T. F.; Yusof, M. R.; Hashim, S.; Ghoshal, S. K.

2018-03-01

Mullite-barite ceramic (MBC) is an emergent material for effective shielding of redundant ionizing radiation exposure. The composition dependent mechanical, thermal, and microstructure properties of MBC that makes MBC a high performing novel radiation shielding candidate remained unexplored. This paper examines the possibility of exploiting Malaysian kaolin (AKIM-35) and barite (BaSO4) derived ceramic (MBC) system for X-ray shielding operation. Using conventional pressing and sintering method six ceramic samples are prepared by mixing AKIM-35 with barite at varying contents (0, 10, 20, 30, 40 and 50 wt%). Synthesized pressed mixtures are calcined at 400 °C for 30 min and then sintered to 1300 °C for 120 min at a heating rate of 10 °C/min. Sintered samples are characterized via X-ray Diffraction (XRD), Field Emission Scanning Electron Microscope (FESEM), lead equivalent (LE), uniformity and dose reduction analyses. XRD pattern of prepared ceramics revealed the presence of monoclinic barium alumino-silicate (BAS) and orthorhombic mullite as major shielding phases together with other minor phase of barite and hexagonal quartz (SiO2) structures. Furthermore, FESEM images of ceramics (between 0 and 30 wt%) displayed the existence of compacted monoclinic plate of BAS and acicular mullite morphology (ceramics at 40 and 50 wt%). Radiation tests displayed the capacity of ceramics (at 0 and 10 wt%) to shield the X-ray radiation emanated at tube potential range of 50-120 kV. The highest radiation attenuation is ascertained at 70 kV where the dose is reduced remarkably between 99.11% and 97.42%. Ceramics at 0 and 10 wt% demonstrated the highest lead (Pb) equivalent thickness (LE) of 0.44 mm and 0.34 mm, respectively. It is established that such MBC may contribute towards the development of shielding material against ionizing radiation in diagnostic radiology (X-ray) dose range.

A soft switching with reduced voltage stress ZVT-PWM full-bridge converter

Science.gov (United States)

Sahin, Yakup; Ting, Naim Suleyman; Acar, Fatih

2018-04-01

This paper introduces a novel active snubber cell for soft switching pulse width modulation DC-DC converters. In the proposed converter, the main switch is turned on under zero voltage transition and turned off under zero voltage switching (ZVS). The auxiliary switch is turned on under zero current switching (ZCS) and turned off under zero current transition. The main diode is turned on under ZVS and turned off under ZCS. All of the other semiconductors in the converter are turned on and off with soft switching. There is no extra voltage stress on the semiconductor devices. Besides, the proposed converter has simple structure and ease of control due to common ground. The detailed theoretical analysis of the proposed converter is presented and also verified with both simulation and experimental study at 100 kHz switching frequency and 600 W output power. Furthermore, the efficiency of the proposed converter is 95.7% at nominal power.

Teaching Soft Skills Employers Need

Science.gov (United States)

Ellis, Maureen; Kisling, Eric; Hackworth, Robbie G.

2014-01-01

This study identifies the soft skills community colleges teach in an office technology course and determines whether the skills taught are congruent with the soft skills employers require in today's entry-level office work. A qualitative content analysis of a community college office technology soft skills course was performed using 23 soft skills…

Spin waves in the soft layer of exchange-coupled soft/hard bilayers

Energy Technology Data Exchange (ETDEWEB)

Xiong, Zheng-min; Ge, Su-qin; Wang, Xi-guang; Li, Zhi-xiong; Xia, Qing-lin; Wang, Dao-wei; Nie, Yao-zhuang; Guo, Guang-hua, E-mail: guogh@mail.csu.edu.cn [School of Physics and Electronics, Central South University, Changsha 410083 (China); Tang, Wei [School of Physics and Electronics, Central South University, Changsha 410083 (China); Suzhou Institute of Nano-tech and Nano-bionics, Chinese Academy of Sciences, Suzhou 215123 (China); Zeng, Zhong-ming [Suzhou Institute of Nano-tech and Nano-bionics, Chinese Academy of Sciences, Suzhou 215123 (China)

2016-05-15

The magnetic dynamical properties of the soft layer in exchange-coupled soft/hard bilayers have been investigated numerically using a one-dimensional atomic chain model. The frequencies and spatial profiles of spin wave eigenmodes are calculated during the magnetization reversal process of the soft layer. The spin wave modes exhibit a spatially modulated amplitude, which is especially evident for high-order modes. A dynamic pinning effect of surface magnetic moment is observed. The spin wave eigenfrequency decreases linearly with the increase of the magnetic field in the uniformly magnetized state and increases nonlinearly with field when spiral magnetization configuration is formed in the soft layer.

Spin waves in the soft layer of exchange-coupled soft/hard bilayers

Directory of Open Access Journals (Sweden)

Zheng-min Xiong

2016-05-01

Full Text Available The magnetic dynamical properties of the soft layer in exchange-coupled soft/hard bilayers have been investigated numerically using a one-dimensional atomic chain model. The frequencies and spatial profiles of spin wave eigenmodes are calculated during the magnetization reversal process of the soft layer. The spin wave modes exhibit a spatially modulated amplitude, which is especially evident for high-order modes. A dynamic pinning effect of surface magnetic moment is observed. The spin wave eigenfrequency decreases linearly with the increase of the magnetic field in the uniformly magnetized state and increases nonlinearly with field when spiral magnetization configuration is formed in the soft layer.

Nasal Soft-Tissue Triangle Deformities.

Science.gov (United States)

Foda, Hossam M T

2016-08-01

The soft-tissue triangle is one of the least areas attended to in rhinoplasty. Any postoperative retraction, notching, or asymmetries of soft triangles can seriously affect the rhinoplasty outcome. A good understanding of the risk factors predisposing to soft triangle deformities is necessary to prevent such problems. The commonest risk factors in our study were the wide vertical domal angle between the lateral and intermediate crura, and the increased length of intermediate crus. Two types of soft triangle grafts were described to prevent and treat soft triangle deformities. The used soft triangle grafts resulted in an excellent long-term aesthetic and functional improvement. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

SCHEME (Soft Control Human error Evaluation MEthod) for advanced MCR HRA

International Nuclear Information System (INIS)

Jang, Inseok; Jung, Wondea; Seong, Poong Hyun

2015-01-01

The Technique for Human Error Rate Prediction (THERP), Korean Human Reliability Analysis (K-HRA), Human Error Assessment and Reduction Technique (HEART), A Technique for Human Event Analysis (ATHEANA), Cognitive Reliability and Error Analysis Method (CREAM), and Simplified Plant Analysis Risk Human Reliability Assessment (SPAR-H) in relation to NPP maintenance and operation. Most of these methods were developed considering the conventional type of Main Control Rooms (MCRs). They are still used for HRA in advanced MCRs even though the operating environment of advanced MCRs in NPPs has been considerably changed by the adoption of new human-system interfaces such as computer-based soft controls. Among the many features in advanced MCRs, soft controls are an important feature because the operation action in NPP advanced MCRs is performed by soft controls. Consequently, those conventional methods may not sufficiently consider the features of soft control execution human errors. To this end, a new framework of a HRA method for evaluating soft control execution human error is suggested by performing the soft control task analysis and the literature reviews regarding widely accepted human error taxonomies. In this study, the framework of a HRA method for evaluating soft control execution human error in advanced MCRs is developed. First, the factors which HRA method in advanced MCRs should encompass are derived based on the literature review, and soft control task analysis. Based on the derived factors, execution HRA framework in advanced MCRs is developed mainly focusing on the features of soft control. Moreover, since most current HRA database deal with operation in conventional type of MCRs and are not explicitly designed to deal with digital HSI, HRA database are developed under lab scale simulation

Holiday fun with soft gluons

CERN Multimedia

CERN. Geneva

2017-01-01

Emissions of soft gluons from energetic particles play an important role in collider processes. While the basic physics of soft emissions is simple, it gives rise to a variety of interesting and intricate phenomena (non-global logs, Glauber phases, super-leading logs, factorization breaking). After an introduction, I will review progress in resummation methods such as Soft-Collinear Effective Theory driven by a better understanding of soft emissions. I will also show some new results for computations of soft-gluon effects in gap-between-jets and isolation-cone cross sections.

Exploring soft constraints on effective actions

Energy Technology Data Exchange (ETDEWEB)

Bianchi, Massimo; Guerrieri, Andrea L. [Dipartimento di Fisica, Università di Roma “Tor Vergata”,I.N.F.N. Sezione di Roma “Tor Vergata”,Via della Ricerca Scientifica, Roma, 00133 (Italy); Huang, Yu-tin; Lee, Chao-Jung [Department of Physics and Astronomy, National Taiwan University,No. 1 Roosevelt Road Sec. 4, Taipei, Taiwan (China); Wen, Congkao [Dipartimento di Fisica, Università di Roma “Tor Vergata”,I.N.F.N. Sezione di Roma “Tor Vergata”,Via della Ricerca Scientifica, Roma, 00133 (Italy)

2016-10-10

We study effective actions for simultaneous breaking of space-time and internal symmetries. Novel features arise due to the mixing of Goldstone modes under the broken symmetries which, in contrast to the usual Adler’s zero, leads to non-vanishing soft limits. Such scenarios are common for spontaneously broken SCFT’s. We explicitly test these soft theorems for N=4 sYM in the Coulomb branch both perturbatively and non-perturbatively. We explore the soft constraints systematically utilizing recursion relations. In the pure dilaton sector of a general CFT, we show that all amplitudes up to order s{sup n}∼∂{sup 2n} are completely determined in terms of the k-point amplitudes at order s{sup k} with k≤n. Terms with at most one derivative acting on each dilaton insertion are completely fixed and coincide with those appearing in the conformal DBI, i.e. DBI in AdS. With maximal supersymmetry, the effective actions are further constrained, leading to new non-renormalization theorems. In particular, the effective action is fixed up to eight derivatives in terms of just one unknown four-point coefficient and one more coefficient for ten-derivative terms. Finally, we also study the interplay between scale and conformal invariance in this context.

Fixing soft margins

NARCIS (Netherlands)

P. Kofman (Paul); A. Vaal, de (Albert); C.G. de Vries (Casper)

1993-01-01

textabstractNon-parametric tolerance limits are employed to calculate soft margins such as advocated in Williamson's target zone proposal. In particular, the tradeoff between softness and zone width is quantified. This may be helpful in choosing appropriate margins. Furthermore, it offers

A dissolution-diffusion sliding model for soft rock grains with hydro-mechanical effect

Directory of Open Access Journals (Sweden)

Z. Liu

2018-06-01

Full Text Available The deformation and failure of soft rock affected by hydro-mechanical (HM effect are one of the most concerns in geotechnical engineering, which are basically attributed to the grain sliding of soft rock. This study tried to develop a dissolution-diffusion sliding model for the typical red bed soft rock in South China. Based on hydration film, mineral dissolution and diffusion theory, and geochemical thermodynamics, a dissolution-diffusion sliding model with the HM effect was established to account for the sliding rate. Combined with the digital image processing technology, the relationship between the grain size of soft rock and the amplitude of sliding surface was presented. An equation for the strain rate of soft rocks under steady state was also derived. The reliability of the dissolution-diffusion sliding model was verified by triaxial creep tests on the soft rock with the HM coupling effect and by the relationship between the inversion average disjoining pressure and the average thickness of the hydration film. The results showed that the sliding rate of the soft rock grains was affected significantly by the waviness of sliding surface, the shear stress, and the average thickness of hydration film. The average grain size is essential for controlling the steady-state creep rate of soft rock. This study provides a new idea for investigating the deformation and failure of soft rock with the HM effect. Keywords: Soft rock, Hydro-mechanical (HM effect, Mineral dissolution-diffusion, Grain sliding model

Advances in Soft Matter Mechanics

CERN Document Server

Li, Shaofan

2012-01-01

"Advances in Soft Matter Mechanics" is a compilation and selection of recent works in soft matter mechanics by a group of active researchers in the field. The main objectives of this book are first to disseminate the latest developments in soft matter mechanics in the field of applied and computational mechanics, and second to introduce soft matter mechanics as a sub-discipline of soft matter physics. As an important branch of soft matter physics, soft matter mechanics has developed rapidly in recent years. A number of the novel approaches discussed in this book are unique, such as the coarse grained finite element method for modeling colloidal adhesion, entropic elasticity, meshfree simulations of liquid crystal elastomers, simulations of DNA, etc. The book is intended for researchers and graduate students in the field of mechanics, condensed matter physics and biomaterials. Dr. Shaofan Li is a professor of the University of California-Berkeley, U.S.A; Dr. Bohua Sun is a professor of Cape Peninsula Universit...

High strain-rate soft material characterization via inertial cavitation

Science.gov (United States)

Estrada, Jonathan B.; Barajas, Carlos; Henann, David L.; Johnsen, Eric; Franck, Christian

2018-03-01

Mechanical characterization of soft materials at high strain-rates is challenging due to their high compliance, slow wave speeds, and non-linear viscoelasticity. Yet, knowledge of their material behavior is paramount across a spectrum of biological and engineering applications from minimizing tissue damage in ultrasound and laser surgeries to diagnosing and mitigating impact injuries. To address this significant experimental hurdle and the need to accurately measure the viscoelastic properties of soft materials at high strain-rates (103-108 s-1), we present a minimally invasive, local 3D microrheology technique based on inertial microcavitation. By combining high-speed time-lapse imaging with an appropriate theoretical cavitation framework, we demonstrate that this technique has the capability to accurately determine the general viscoelastic material properties of soft matter as compliant as a few kilopascals. Similar to commercial characterization algorithms, we provide the user with significant flexibility in evaluating several constitutive laws to determine the most appropriate physical model for the material under investigation. Given its straightforward implementation into most current microscopy setups, we anticipate that this technique can be easily adopted by anyone interested in characterizing soft material properties at high loading rates including hydrogels, tissues and various polymeric specimens.

Morphoagrobiological properties and productivity of new soft winter wheat varieties under the conditions of Kirovohrad variety testing station

Directory of Open Access Journals (Sweden)

О. Л. Уліч

2017-03-01

Full Text Available Purpose. To study morphoagrobiological and adaptive properties, level of yielding capacity of recently registered soft winter wheat varieties of various ecological groups under agroecological conditions of Kirovohrad variety testing station. Methods. Field study, laboratory test, analytical procedure and statistical evaluation. Results. It was established that the yield level of is a key composite indicator of genotype adaptation to agroecological growing conditions. Experimental data indicate significant deviations of yield depending on the genotype and the year of study. During three years of experiments, yield depending of the variety ranged from 4.26 to 9.71 t/ha, such varieties as ‘CN Kombin’, ‘Estivus’, ‘Tradytsiia odeska’, ‘Mudrist odeska’, ‘Lil’ and ‘Fabius’ had higher yields. In case of dry weather conditions and unfavorable agro-ecological factors, the following varieties as ‘Mudrist odeska’, ‘Veteran’, ‘Lil’, ‘Tsentylivka’, ‘Fabius’, ‘Patras’, ‘Montrei’ have demonstrated good adaptive properties. Their yield has decreased by 9,2–19,0%, while in the varieties ‘Mahistral’, ‘Poltavka’, ‘Harantiia odeska’ and ‘Pokrova’ – by 34.4, 42.4, 45.2 and 50.6% accordingly. Conclusions. Investigated soft winter wheat varieties differ in morphoagrobiological characteristics, productivity, height, maturation period, adaptability as well as economic and agronomic value. According to the complex of such indices as productivity, agronomic characters and properties as well as adaptability, in the microzone of Kirovohrad variety testing station it is advisable to grow varie­ties ‘CN Kombi’, ‘Pokrova’, ‘Mudrist odeska’, ‘Veteran’ and ‘Lil’.

Clinical management of soft tissue sarcomas

International Nuclear Information System (INIS)

Pinedo, H.M.; Verweij, J.

1986-01-01

This book is concerned with the clinical management of soft tissue sarcomas. Topics covered include: Radiotherapy; Pathology of soft tissue sarcomas; Surgical treatment of soft tissue sarcomas; and Chemotherapy in advanced soft tissue sarcomas

Magnetic resonance imaging indicators of blood-brain barrier and brain water changes in young rats with kaolin-induced hydrocephalus.

Science.gov (United States)

Del Bigio, Marc R; Slobodian, Ili; Schellenberg, Angela E; Buist, Richard J; Kemp-Buors, Tanya L

2011-08-11

Hydrocephalus is associated with enlargement of cerebral ventricles. We hypothesized that magnetic resonance (MR) imaging parameters known to be influenced by tissue water content would change in parallel with ventricle size in young rats and that changes in blood-brain barrier (BBB) permeability would be detected. Hydrocephalus was induced by injection of kaolin into the cisterna magna of 4-week-old rats, which were studied 1 or 3 weeks later. MR was used to measure longitudinal and transverse relaxation times (T1 and T2) and apparent diffusion coefficients in several regions. Brain tissue water content was measured by the wet-dry weight method, and tissue density was measured in Percoll gradient columns. BBB permeability was measured by quantitative imaging of changes on T1-weighted images following injection of gadolinium diethylenetriamine penta-acetate (Gd-DTPA) tracer and microscopically by detection of fluorescent dextran conjugates. In nonhydrocephalic rats, water content decreased progressively from age 3 to 7 weeks. T1 and T2 and apparent diffusion coefficients did not exhibit parallel changes and there was no evidence of BBB permeability to tracers. The cerebral ventricles enlarged progressively in the weeks following kaolin injection. In hydrocephalic rats, the dorsal cortex was more dense and the white matter less so, indicating that the increased water content was largely confined to white matter. Hydrocephalus was associated with transient elevation of T1 in gray and white matter and persistent elevation of T2 in white matter. Changes in the apparent diffusion coefficients were significant only in white matter. Ventricle size correlated significantly with dorsal water content, T1, T2, and apparent diffusion coefficients. MR imaging showed evidence of Gd-DTPA leakage in periventricular tissue foci but not diffusely. These correlated with microscopic leak of larger dextran tracers. MR characteristics cannot be used as direct surrogates for water

Magnetic resonance imaging indicators of blood-brain barrier and brain water changes in young rats with kaolin-induced hydrocephalus

Directory of Open Access Journals (Sweden)

Del Bigio Marc R

2011-08-01

Full Text Available Abstract Background Hydrocephalus is associated with enlargement of cerebral ventricles. We hypothesized that magnetic resonance (MR imaging parameters known to be influenced by tissue water content would change in parallel with ventricle size in young rats and that changes in blood-brain barrier (BBB permeability would be detected. Methods Hydrocephalus was induced by injection of kaolin into the cisterna magna of 4-week-old rats, which were studied 1 or 3 weeks later. MR was used to measure longitudinal and transverse relaxation times (T1 and T2 and apparent diffusion coefficients in several regions. Brain tissue water content was measured by the wet-dry weight method, and tissue density was measured in Percoll gradient columns. BBB permeability was measured by quantitative imaging of changes on T1-weighted images following injection of gadolinium diethylenetriamine penta-acetate (Gd-DTPA tracer and microscopically by detection of fluorescent dextran conjugates. Results In nonhydrocephalic rats, water content decreased progressively from age 3 to 7 weeks. T1 and T2 and apparent diffusion coefficients did not exhibit parallel changes and there was no evidence of BBB permeability to tracers. The cerebral ventricles enlarged progressively in the weeks following kaolin injection. In hydrocephalic rats, the dorsal cortex was more dense and the white matter less so, indicating that the increased water content was largely confined to white matter. Hydrocephalus was associated with transient elevation of T1 in gray and white matter and persistent elevation of T2 in white matter. Changes in the apparent diffusion coefficients were significant only in white matter. Ventricle size correlated significantly with dorsal water content, T1, T2, and apparent diffusion coefficients. MR imaging showed evidence of Gd-DTPA leakage in periventricular tissue foci but not diffusely. These correlated with microscopic leak of larger dextran tracers. Conclusions MR

Differences in Train-induced Vibration between Hard Soil and Soft Soil

Science.gov (United States)

Noyori, M.; Yokoyama, H.

2017-12-01

Vibration and noise caused by running trains sometimes raises environmental issues. Train-induced vibration is caused by moving static and dynamic axle loads. To reduce the vibration, it is important to clarify the conditions under which the train-induced vibration increases. In this study, we clarified the differences in train-induced vibration between on hard soil and on soft soil using a numerical simulation method. The numerical simulation method we used is a combination of two analysis. The one is a coupled vibration analysis model of a running train, a track and a supporting structure. In the analysis, the excitation force of the viaduct slabs generated by a running train is computed. The other analysis is a three-dimensional vibration analysis model of a supporting structure and the ground into which the excitation force computed by the former analysis is input. As a result of the numerical simulation, the ground vibration in the area not more than 25m from the center of the viaduct is larger under the soft soil condition than that under the hard soil condition in almost all frequency ranges. On the other hand, the ground vibration of 40 and 50Hz at a point 50m from the center of the viaduct under the hard soil condition is larger than that under the soft soil condition. These are consistent with the result of the two-dimensional FEM based on a ground model alone. Thus, we concluded that these results are obtained from not the effects of the running train but the vibration characteristics of the ground.

Soft optics in intelligent optical networks

Science.gov (United States)

Shue, Chikong; Cao, Yang

2001-10-01

In addition to the recent advances in Hard-optics that pushes the optical transmission speed, distance, wave density and optical switching capacity, Soft-optics provides the necessary intelligence and control software that reduces operational costs, increase efficiency, and enhances revenue generating services by automating optimal optical circuit placement and restoration, and enabling value-added new services like Optical VPN. This paper describes the advances in 1) Overall Hard-optics and Soft-optics 2) Layered hierarchy of Soft-optics 3) Component of Soft-optics, including hard-optics drivers, Management Soft-optics, Routing Soft-optics and System Soft-optics 4) Key component of Routing and System Soft-optics, namely optical routing and signaling (including UNI/NNI and GMPLS signaling). In summary, the soft-optics on a new generation of OXC's enables Intelligent Optical Networks to provide just-in-time service delivery and fast restoration, and real-time capacity management that eliminates stranded bandwidth. It reduces operational costs and provides new revenue opportunities.

Soft color interactions and diffractive hard scattering at the Tevatron

International Nuclear Information System (INIS)

Enberg, R.; Timneanu, N.; Ingelman, G.; Uppsala Univ.

2001-06-01

An improved understanding of nonperturbative QCD can be obtained by the recently developed soft color interaction models. Their essence is the variation of color string-field topologies, giving a unified description of final states in high energy interactions, e.g., diffractive and nondiffractive events in ep and pp. Here we present a detailed study of such models (the soft color interaction model and the generalized area law model) applied to pp, considering also the general problem of the underlying event including beam particle remnants. With models turned to HERA ep data, we find a good description also of Tevatron data on production of W, bottom and jets in diffractive events defined either by leading antiprotons or by one or two rapidity gaps in the forward or backward regions. We also give predictions for diffractive J/ψ production where the soft exchange mechanism produces both a gap and a color singlet cc state in the same event. This soft color interaction approach is also compared with Pomeron-based models for diffraction, and some possibilities to experimentally discriminate between these different approaches are discussed. (orig.)

Response characteristics of reactor building on weathered soft rock ground

International Nuclear Information System (INIS)

Hirata, Kazuta; Tochigi, Hitoshi

1991-01-01

The purpose of this study is to investigate the seismic stability of nuclear power plants on layered soft bedrock grounds, focusing on the seismic response of reactor buildings. In this case, the soft bedrock grounds refer to the weathered soft bedrocks with several tens meter thickness overlaying hard bedrocks. Under this condition, there are two subjects regarding the estimation of the seismic response of reactor buildings. One is the estimation of the seismic response of surface ground, and another is the estimation of soil-structure interaction characteristics for the structures embedded in the layered grounds with low impedandce ratio between the surface ground and the bedrock. Paying attention to these subjects, many cases of seismic response analysis were carried out, and the following facts were clarified. In the soft rock grounds overlaying hard bedrocks, it was proved that the response acceleration was larger than the case of uniform hard bedrocks. A simplified sway and rocking model was proposed to consider soil-structure interaction. It was proved that the response of reactor buildings was small when the effect of embedment was considered. (K.I.)

The Transmission of Huizhou Culture to Foreign Students in China——Under the Context of Soft Power

Institute of Scientific and Technical Information of China (English)

Yao Yong

2017-01-01

Culture is an important aspect of soft power.Huizhou Culture is one of the best representations of traditional Chinese culture and has been attached great importance by scholars both at home and aboard.It's vitally important to spread Huizhou Cultural values around the world to improve China's soft power.Foreign students in China are potential advocators of Chinese Culture.The cultural information they get will be transmitted to their own countries.We should take some strategies to promote Huizhou Culture among foreign students so that the charm of Huizhou Culture can be noticed and recognized by many more people.

Study on the NaOH/metakaolin ratio and crystallization time for zeolite a synthesis from kaolin using statistical design

Energy Technology Data Exchange (ETDEWEB)

Silva Filho, Severino Higino da; Bieseki, Lindiane; Pergher, Sibele Berenice Castella, E-mail: sibelepergher@gmail.com [Universidade Federal do Rio Grande do Norte (LABPEMOL/UFRN), Natal, RN (Brazil). Lab. de Peneiras Moleculares; Maia, Ana Aurea B.; Angelica, Romulo Simoes [Universidade Federal do Para (UFPA), Belem PA (Brazil); Treichel, Helen [Universidade Federal da Fronteira Sil (UFFS), Erechim, RS (Brazil)

2017-05-15

The NaOH/metakaolin ratio and crystallization time were studied for the synthesis of zeolite NaA from a sample of kaolin from a Capim mine. The tests were carried out by using statistical design with axial points and replication of the central point. The samples obtained were characterized by X-ray diffraction (DRX), scanning electron microscopy and chemical analysis using a microprobe EPMA. The results showed that there is a relationship between the amount of NaOH added and crystallization time. The tests carried out using the lowest NaOH/metakaolin ratio (0.5) and the shortest time (4 h) produced a non-crystalline material. On the other hand, increasing the NaOH/metakaolin ratio and the crystallization time led to the formation of a NaA phase with a high structural level, but with the presence of a sodalite phase as an impurity. (author)

CHARACTERIZATIONS OF FUZZY SOFT PRE SEPARATION AXIOMS

OpenAIRE

El-Latif, Alaa Mohamed Abd

2015-01-01

− The notions of fuzzy pre open soft sets and fuzzy pre closed soft sets were introducedby Abd El-latif et al. [2]. In this paper, we continue the study on fuzzy soft topological spaces andinvestigate the properties of fuzzy pre open soft sets, fuzzy pre closed soft sets and study variousproperties and notions related to these structures. In particular, we study the relationship betweenfuzzy pre soft interior fuzzy pre soft closure. Moreover, we study the properties of fuzzy soft pre regulars...

Penggunaan Teknik Analisis Dalam Pengembangan Sistem Informasi Menggunakan Soft System Methodology (SSM)

OpenAIRE

Sumadyo, Malikus

2016-01-01

Soft Systems Methodology (SSM) is a systematic method of information system development using a structured approach to understanding an issue, building a conceptual mode, getting the feasibility and the desired changes and to be implemented. The system being developed using Soft Systems Methodology aimed at addressing organizational, which is used to respond to the symptoms caused by an underlying problem that has not been previously known. Organizations can be regarded as an open system so...

REVIEW OF SOFT SKILLS AMONG TRAINERS FROM ADVANCED TECHNOLOGY TRAINING CENTER (ADTEC)

OpenAIRE

Mohd Hasril Amiruddin; Norhayati Ngadiman; Romy Abdul Kadir; Sukartini Saidy

2016-01-01

The Advanced Technology Training Centre (ADTEC) institutions under the Ministry of Human Resource are major players for skilled human resource development in Malaysia. In preparing for the competent workforce, ADTECs are taking active measures to ensure that their trainees are equipped with the necessary soft skills –in addition to technical skill - that are much needed to deal with the complex and challenging workplace. However, integrating soft skills into the training that has traditionall...

Multi-Purpose Artificial Muscle and Sensor Array for Untethered Soft Robots

Data.gov (United States)

National Aeronautics and Space Administration — “Soft” machines and electronics contain little or no rigid material and remain functional under large elastic deformation. Because they are soft, lightweight, impact...

Soft Hair on Black Holes

Science.gov (United States)

Hawking, Stephen W.; Perry, Malcolm J.; Strominger, Andrew

2016-06-01

It has recently been shown that Bondi-van der Burg-Metzner-Sachs supertranslation symmetries imply an infinite number of conservation laws for all gravitational theories in asymptotically Minkowskian spacetimes. These laws require black holes to carry a large amount of soft (i.e., zero-energy) supertranslation hair. The presence of a Maxwell field similarly implies soft electric hair. This Letter gives an explicit description of soft hair in terms of soft gravitons or photons on the black hole horizon, and shows that complete information about their quantum state is stored on a holographic plate at the future boundary of the horizon. Charge conservation is used to give an infinite number of exact relations between the evaporation products of black holes which have different soft hair but are otherwise identical. It is further argued that soft hair which is spatially localized to much less than a Planck length cannot be excited in a physically realizable process, giving an effective number of soft degrees of freedom proportional to the horizon area in Planck units.

Soft Hair on Black Holes.

Science.gov (United States)

Hawking, Stephen W; Perry, Malcolm J; Strominger, Andrew

2016-06-10

It has recently been shown that Bondi-van der Burg-Metzner-Sachs supertranslation symmetries imply an infinite number of conservation laws for all gravitational theories in asymptotically Minkowskian spacetimes. These laws require black holes to carry a large amount of soft (i.e., zero-energy) supertranslation hair. The presence of a Maxwell field similarly implies soft electric hair. This Letter gives an explicit description of soft hair in terms of soft gravitons or photons on the black hole horizon, and shows that complete information about their quantum state is stored on a holographic plate at the future boundary of the horizon. Charge conservation is used to give an infinite number of exact relations between the evaporation products of black holes which have different soft hair but are otherwise identical. It is further argued that soft hair which is spatially localized to much less than a Planck length cannot be excited in a physically realizable process, giving an effective number of soft degrees of freedom proportional to the horizon area in Planck units.

Soft skills and dental education.

Science.gov (United States)

Gonzalez, M A G; Abu Kasim, N H; Naimie, Z

2013-05-01

Soft skills and hard skills are essential in the practice of dentistry. While hard skills deal with technical proficiency, soft skills relate to a personal values and interpersonal skills that determine a person's ability to fit in a particular situation. These skills contribute to the success of organisations that deal face-to-face with clients. Effective soft skills benefit the dental practice. However, the teaching of soft skills remains a challenge to dental schools. This paper discusses the different soft skills, how they are taught and assessed and the issues that need to be addressed in their teaching and assessment. The use of the module by the Faculty of Dentistry, University of Malaya for development of soft skills for institutions of higher learning introduced by the Ministry of Higher Education, Malaysia. © 2013 John Wiley & Sons A/S. Published by Blackwell Publishing Ltd.

Soft Matter Characterization

CERN Document Server

Borsali, Redouane

2008-01-01

Progress in basic soft matter research is driven largely by the experimental techniques available. Much of the work is concerned with understanding them at the microscopic level, especially at the nanometer length scales that give soft matter studies a wide overlap with nanotechnology. This 2 volume reference work, split into 4 parts, presents detailed discussions of many of the major techniques commonly used as well as some of those in current development for studying and manipulating soft matter. The articles are intended to be accessible to the interdisciplinary audience (at the graduate student level and above) that is or will be engaged in soft matter studies or those in other disciplines who wish to view some of the research methods in this fascinating field. Part 1 contains articles with a largely (but, in most cases, not exclusively) theoretical content and/or that cover material relevant to more than one of the techniques covered in subsequent volumes. It includes an introductory chapter on some of t...

Soft bio-integrated systems for continuous health monitoring

Science.gov (United States)

Raj, M.; Wei, P. H.; Morey, B.; Wang, X.; Keen, B.; DePetrillo, P.; Hsu, Y. Y.; Ghaffari, R.

2014-06-01

Electronically-enabled wearable systems that monitor physiological activity and electrophysiological activity hold the key to truly personalized medical care outside of the hospital setting. However, fundamental technical challenges exist in achieving medical systems that are comfortable, unobtrusive and fully integrated without external connections to bench top instruments. In particular, there is a fundamental mismatch in mechanical coupling between existing classes of rigid electronics and soft biological substrates, like the skin. Here we describe new mechanical and electrical design strategies for wearable devices with mechanical properties that approach that of biological tissue. These systems exploit stretchable networks of conformal sensors (i.e. electrodes, temperature sensors, and accelerometers) and associated circuitry (i.e. microcontroller, memory, voltage regulators, rechargeable battery, wireless communication modules) embedded in ultrathin, elastomeric substrates. Quantitative analyses of sensor performance and mechanics under tensile and torsional stresses illustrate the ability to mechanically couple with soft tissues in a way that is mechanically invisible to the user. Representative examples of these soft biointegrated systems can be applied for continuous sensing of muscle and movement activity in the home and ambulatory settings.

Osteotomy simulation and soft tissue prediction using computer tomography scans

International Nuclear Information System (INIS)

Teschner, M.; Girod, S.; Girod, B.

1999-01-01

In this paper, a system is presented that can be used to simulate osteotomies of the skull and to estimate the resulting of tissue changes. Thus, the three-dimensional, photorealistic, postoperative appearance of a patient can be assessed. The system is based on a computer tomography scan and a photorealistic laser scan of the patient's face. In order to predict the postoperative appearance of a patient the soft tissue must follow the movement of the underlying bone. In this paper, a multi-layer soft tissue model is proposed that is based on springs. It incorporates features like skin turgor, gravity and sliding bone contact. The prediction of soft tissue changes due to bone realignments is computed using a very efficient and robust optimization method. The system can handle individual patient data sets and has been tested with several clinical cases. (author)

Multiattribute Grey Target Decision Method Based on Soft Set Theory

Directory of Open Access Journals (Sweden)

Xia Wang

2014-01-01

Full Text Available With respect to the Multiattribute decision-making problems in which the evaluation attribute sets are different and the evaluating values of alternatives are interval grey numbers, a multiattribute grey target decision-making method in which the attribute sets are different was proposed. The concept of grey soft set was defined, and its “AND” operation was assigned by combining the intersection operation of grey number. The expression approach of new grey soft set of attribute sets considering by all decision makers were gained by applying the “AND” operation of grey soft set, and the weights of synthesis attribute were proved. The alternatives were ranked according to the size of distance of bull’s eyes of each alternative under synthetic attribute sets. The green supplier selection was illustrated to demonstrate the effectiveness of proposed model.

Soft Manipulators and Grippers: A Review

Directory of Open Access Journals (Sweden)

Josie Hughes

2016-11-01

Full Text Available Soft robotics is a growing area of research which utilises the compliance and adaptability of soft structures to develop highly adaptive robotics for soft interactions. One area in which soft robotics has the ability to make significant impact is in the development of soft grippers and manipulators. With an increased requirement for automation, robotics systems are required to perform task in unstructured and not well defined environments; conditions which conventional rigid robotics are not best suited. This requires a paradigm shift in the methods and materials used to develop robots such that they can adapt to and work safely in human environments. One solution to this is soft robotics, which enables soft interactions with the surroundings whilst maintaining the ability to apply significant force. This review paper assess the current materials and methods, actuation methods and sensors which are used in the development of soft manipulators. The achievements and shortcomings of recent technology in these key areas are evaluated, and this paper concludes with a discussion on the potential impacts of soft manipulators on industry and society.

Soft tissue thin-plate spline analysis of pre-pubertal Korean and European-Americans with untreated Angle's Class III malocclusions.

Science.gov (United States)

Singh, G D; McNamara, J A; Lozanoff, S

1999-01-01

The purpose of this study was to assess soft tissue facial matrices in subjects of diverse ethnic origins with underlying dentoskeletal malocclusions. Pre-treatment lateral cephalographs of 71 Korean and 70 European-American children aged between 5 and 11 years with Angle's Class III malocclusions were traced, and 12 homologous, soft tissue landmarks digitized. Comparing mean Korean and European-American Class III soft tissue profiles, Procrustes analysis established statistical difference (P thin-plate spline analysis indicated that both affine and non-affine transformations contribute towards the total spline (deformation) of the averaged Class III soft tissue configurations. For non-affine transformations, partial warp (PW) 8 had the highest magnitude, indicating large-scale deformations visualized as labio-mental protrusion, predominantly. In addition, PW9, PW4, and PW5 also had high magnitudes, demonstrating labio-mental vertical compression and antero-posterior compression of the lower labio-mental soft tissues. Thus, Korean children with Class III malocclusions demonstrate antero-posterior and vertical deformations of the labio-mental soft tissue complex with respect to their European-American counterparts. Morphological heterogeneity of the soft tissue integument in subjects of diverse ethnic origin may obscure the underlying skeletal morphology, but the soft tissue integument appears to have minimal ontogenetic association with Class III malocclusions.

Aluminium silicate fertilization in the quality of wheat seeds under salt stress

Directory of Open Access Journals (Sweden)

César Iván Suárez Castellanos

2015-06-01

Full Text Available Wheat is used as raw material in the production of several foods and it is the first cereal as in the world production of grains. However, the agricultural production is limited for the salinity effect in about 50% of irrigated areas in the world. An alternative to reduce the salt stresses caused in the plants is the silicon use. The objective of this study was to evaluate the fertilizing effect with aluminum silicate using kaolin as a source, on seed quality of wheat produced under salt stress. The experiment was accomplished in greenhouse using wheat seeds of Quartzo cultivar sowed in pots of 10 L containing soil and maintained until harvest. The kaolin (77.9% SiO2 was applied in doses of 0 (control; 1,000; 2,000 and 3,000 kg ha-1. Salt stress was simulated through irrigation with NaCl solutions in the concentrations of 0 (control, 8 and 16 mM. Agronomic characteristics and the physiologic seed quality were evaluated. The results showed that the salt irrigation caused decrease in the number of ears per plant, number of ears with seeds, in the weight of the ears without threshing and in the weight of the produced seeds. The aluminum silicate use increased the weight of a thousand seeds independent of the presence of salt stress. Silicon application contributed to increase the percentage of germination of the produced seeds when the plants were not exposed to the salt stress.

Soft decoding a self-dual (48, 24; 12) code

Science.gov (United States)

Solomon, G.

1993-01-01

A self-dual (48,24;12) code comes from restricting a binary cyclic (63,18;36) code to a 6 x 7 matrix, adding an eighth all-zero column, and then adjoining six dimensions to this extended 6 x 8 matrix. These six dimensions are generated by linear combinations of row permutations of a 6 x 8 matrix of weight 12, whose sums of rows and columns add to one. A soft decoding using these properties and approximating maximum likelihood is presented here. This is preliminary to a possible soft decoding of the box (72,36;15) code that promises a 7.7-dB theoretical coding under maximum likelihood.

Application of 3D Electrical Resistivity Tomography As A Tool for Mapping Subsurface Cavities in a Kaolin Mining Site at Kankara in North Central Nigeria.

Science.gov (United States)

Eshimiakhe, D.; Jimoh, R.

2017-12-01

A Kaolin mining site at Dajin Gwanma in north central Nigeria was investigated to determine the possibility of using 3D ERT to detect subsurface voids created due to mining of kaolin deposit and to perhaps suggest areas prone to subsidence. This study was undertaken on conceptual resistivity model that subsurface voids characterized by higher or lower resistivity than the host, depending on weather the void is in-filled water or not. The data collection was carried out with Terrameter SAS 4000 and ES 464 electrode selector equipment. Dipole-dipole configuration at electrode spacing of 5m was used to acquire the data along parallel profiles laid at equal interval in the study area. While the acquired data along each profile were inverted with 2D algorithm, a script file was created to collate the 2D data set into a 3D format and subsequently inverted using 3D algorithm. A volumetric resistivity model block of the study area was also created using the voxler 4 software. The results show that the voids are characterized by high resistivity (950Ωm-2500Ωm) at depth of between 0-4m and low resistivity (10Ωm-100Ωm) at a depth of 5-30m indicating both air-filled and water-filled voids respectively. The study shows that the voids increase in dimension with depth in NW-SE direction, suggesting that the voids are trending most probably along vertical bedrock joints. It also suggest that voids may overtime grow large enough that the overlying top soil can no longer bridge it, leading to its collapse.

THE EFFECTS OF MAXILLARY EXPANSION ON THE SOFT TISSUE FACIAL PROFILE

Directory of Open Access Journals (Sweden)

Işıl ARAS

2017-10-01

Full Text Available Purpose: The aims of this retrospective study were to evaluate the possible changes in soft tissue facial profile induced by orthopedic rapid maxillary expansion (RME and surgically assisted rapid maxillary expansion (SARME, and to correlate them with the underlying hard tissue alterations. Materials and Methods: 16 patients who received bone borne SARME and 25 patients who were subjected to RME using metal cast splint hyrax appliance were analyzed retrospectively. This research was conducted on lateral cephalometric radiographs taken on 2 occasions: before expansion (T1 and at the beginning of any further orthodontic treatment (T2. Investigated lateral cephalometric parameters consisted of Holdaway soft tissue measurements with some supplementary soft tissue, skeletal and dental assessments. Results: The acquisition of T2 cephalograms which conforms to the initiation of further orthodontic treatment corresponded to 83.25±3.51 days for SARME and 85.68±4.37 days for RME after the expansion was completed. The only significant change in soft tissue profile of the SARME group was a decrease in upper lip thickness (p<0.05, whereas in the RME group, decrease in soft tissue facial profile angle and increase in H angle were found to be statistically significant (p<0.05 for each. For the RME group, the changes in soft tissue facial profile angle and H angle correlated only with the changes in SNB angle (p<0.05. Conclusion: While bone-borne SARME did not seem to possess the potential to alter soft tissue profile, tooth-borne RME caused a more convex soft tissue profile related to a reduction in SNB.

Critical issues in soft rocks

OpenAIRE

Milton Assis Kanji

2014-01-01

This paper discusses several efforts made to study and investigate soft rocks, as well as their physico-mechanical characteristics recognized up to now, the problems in their sampling and testing, and the possibility of its reproduction through artificially made soft rocks. The problems in utilizing current and widespread classification systems to some types of weak rocks are also discussed, as well as other problems related to them. Some examples of engineering works in soft rock or in soft ...

Soft skills and dental education

OpenAIRE

Gonzalez, M. A. G.; Abu Kasim, N. H.; Naimie, Z.

2014-01-01

Soft skills and hard skills are essential in the practice of dentistry. While hard skills deal with technical proficiency, soft skills relate to a personal values and interpersonal skills that determine a person's ability to fit in a particular situation. These skills contribute to the success of organisations that deal face-to-face with clients. Effective soft skills benefit the dental practice. However, the teaching of soft skills remains a challenge to dental schools. This paper discusses ...

MANAGEMENT SOFT-FACTORS IN INDUSTRIES

Directory of Open Access Journals (Sweden)

L. V. Fatkin

2012-01-01

Full Text Available No proper attention is given in existing management theories and concepts to systematization and analysis of non-material management factors, so-called «soft-factors». In industries, management soft-factors may be treated in a broader way. An example of a broader treatment of management soft-factors is given for the system of state regulation of foreign trade activities in industries along with specification, determination and rating of organizational and administrative management soft-factors.

Soft Clouding

DEFF Research Database (Denmark)

Søndergaard, Morten; Markussen, Thomas; Wetton, Barnabas

2012-01-01

Soft Clouding is a blended concept, which describes the aim of a collaborative and transdisciplinary project. The concept is a metaphor implying a blend of cognitive, embodied interaction and semantic web. Furthermore, it is a metaphor describing our attempt of curating a new semantics of sound...... archiving. The Soft Clouding Project is part of LARM - a major infrastructure combining research in and access to sound and radio archives in Denmark. In 2012 the LARM infrastructure will consist of more than 1 million hours of radio, combined with metadata who describes the content. The idea is to analyse...... the concept of ‘infrastructure’ and ‘interface’ on a creative play with the fundamentals of LARM (and any sound archive situation combining many kinds and layers of data and sources). This paper will present and discuss the Soft clouding project from the perspective of the three practices and competencies...

Power suppressed operators and gauge invariance in soft-collinear effective theory

International Nuclear Information System (INIS)

Bauer, Christian W.; Pirjol, Dan; Stewart, Iain W.

2003-01-01

The form of collinear gauge invariance for power suppressed operators in the soft-collinear effective theory (SCET) is discussed. Using a field redefinition we show that it is possible to make any power suppressed ultrasoft-collinear operators invariant under the original leading order gauge transformations. Our manipulations avoid gauge fixing. The Lagrangians to O(λ 2 ) are given in terms of these new fields. We then give a simple procedure for constructing power suppressed soft-collinear operators in SCET II by using an intermediate theory SCET I

Soft theorems from conformal field theory

International Nuclear Information System (INIS)

Lipstein, Arthur E.

2015-01-01

Strominger and collaborators recently proposed that soft theorems for gauge and gravity amplitudes can be interpreted as Ward identities of a 2d CFT at null infinity. In this paper, we will consider a specific realization of this CFT known as ambitwistor string theory, which describes 4d Yang-Mills and gravity with any amount of supersymmetry. Using 4d ambtwistor string theory, we derive soft theorems in the form of an infinite series in the soft momentum which are valid to subleading order in gauge theory and sub-subleading order in gravity. Furthermore, we describe how the algebra of soft limits can be encoded in the braiding of soft vertex operators on the worldsheet and point out a simple relation between soft gluon and soft graviton vertex operators which suggests an interesting connection to color-kinematics duality. Finally, by considering ambitwistor string theory on a genus one worldsheet, we compute the 1-loop correction to the subleading soft graviton theorem due to infrared divergences.

The softness of an atom in a molecule and a functional group softness definition; an LCAO scale

International Nuclear Information System (INIS)

Giambiagi, M.; Giambiagi, M.S. de; Pires, J.M.; Pitanga, P.

1987-01-01

We introduce a scale for the softness of an atom in different molecules and we similarly define a functional group softness. These definitions, unlike previous ones, are not tied to the finite difference approximation neither, hence, to valence state ionization potentials and electron affinities; they result from the LCAO calculation itself. We conclude that a) the softness of an atom in a molecule shows wide variations; b) the geometric average of the softnesses of the atoms in the molecule gives the most consistent results for the molecular softnesses; c) the functional group softness is transferable within a homologous series. (Author) [pt

Int-Soft Interior Hyperideals of Ordered Semihypergroups

Directory of Open Access Journals (Sweden)

Asghar Khan

2017-07-01

Full Text Available The main theme of this paper is to study ordered semihypergroups in the context of int-soft interior hyperideals. In this paper, the notion of int-soft interior hyperideals are studied and their related properties are discussed. We present characterizations of interior hyperideals in terms of int-soft interior hyperideals. The concepts of int-soft hyperideals and int-soft interior hyperideals coincide in a regular as well as in intra-regular ordered semihypergroups. We prove that every int-soft hyperideal is an int-soft interior hyperideal but the converse is not true which is shown with help of an example. Furthermore we characterize simple ordered semihypergroups by means of int-soft hyperideals and int-soft interior hyperideals.

Soft tissue augmentation - Use of hyaluronic acid as dermal filler

Directory of Open Access Journals (Sweden)

Vedamurthy Maya

2004-11-01

Full Text Available Soft tissue augmentation has revolutionized the treatment of the aging face. It is a technique in which a substance is injected under the skin. The concept of utilizing materials for soft tissue augmentation actually began around 1950 with the use of fluid silicone. Today we have a large armamentarium of implant materials to delay the tell tale signs of aging. Filling has replaced conventional surgery in facial rejuvenation. In this article, the emphasis will be on hyaluronic acid as this substance is easily available in India and ranks among the most widely used dermal fillers.

Soft tissue augmentation - Use of hyaluronic acid as dermal filler

Directory of Open Access Journals (Sweden)

Vedamurthy Maya

2004-01-01

Full Text Available Soft tissue augmentation has revolutionized the treatment of the aging face. It is a technique in which a substance is injected under the skin. The concept of utilizing materials for soft tissue augmentation actually began around 1950 with the use of fluid silicone. Today we have a large armamentarium of implant materials to delay the tell tale signs of aging. Filling has replaced conventional surgery in facial rejuvenation. In this article, the emphasis will be on hyaluronic acid as this substance is easily available in India and ranks among the most widely used dermal fillers.

Introduction to soft-collinear effective theory

CERN Document Server

Becher, Thomas; Ferroglia, Andrea

2015-01-01

Among resummation techniques for perturbative QCD in the context of collider and flavor physics, soft-collinear effective theory (SCET) has emerged as both a powerful and versatile tool, having been applied to a large variety of processes, from B-meson decays to jet production at the LHC.  This book provides a concise, pedagogical introduction to this technique. It discusses the expansion of Feynman diagrams around the high-energy limit, followed by the explicit construction of the effective Lagrangian - first for a scalar theory, then for QCD. The underlying concepts are illustrated with the quark vector form factor at large momentum transfer, and the formalism is applied to compute soft-gluon resummation and to perform transverse-momentum resummation for the Drell-Yan process utilizing renormalization group evolution in SCET. Finally, the infrared structure of n-point gauge-theory amplitudes is analyzed by relating them to effective-theory operators. This text is suitable for graduate students and non-spe...

Effect of Compatibilizer on the Dynamic Mechanical and Electrical Properties of Kaolin Clay Reinforced EPDM Rubber

International Nuclear Information System (INIS)

Sarkhel, G.; Manjhi, S.

2013-01-01

Industrial pollution issue and dark colour of carbon black, clay based non black filler are getting more importance for reinforcing elastomer. EPDM-Kaolin composites with various maleated EPDM concentration have been prepared by mixing on a two roll mill. The rheometry data showed the optimum cure time increases with increasing compatibilizer concentration without decreasing torque value indicating that acidic functional groups comes from compatibilizer could retard cure rate and increase the optimum cure time rather than change in the ultimate cure state. As the filler concentration increases, the edge to edge and face to edge interaction between filler and EPDM increases and the free volume between EPDM molecules is reduced, the storage modulus increases. Moreover, the dynamic mechanical analysis also showed the increase in glass transition temperature with increase in filler concentration due to the inter-tubular diffusion of EPDM inside the clay. It was also observed that with increasing filler concentration, the resistivity and dielectric strength decreases and moreover with increasing compatibilizer concentration the resistivity decreases due to better dispersion of filler helps to build conduction path. The morphological study also revealed that homogeneity of filler dispersion increases with increase in compatibilizer concentration. (author)

Preparing soft-bodied arthropods for microscope examination: Soft Scales (Insecta: Hemiptera: Coccidae)

Science.gov (United States)

Proper identification of soft scales (Hemiptera:Coccidae) requires preparation of the specimen on a microscope slide. This training video provides visual instruction on how to prepare soft scale specimens on microscope slides for examination and identification. Steps ranging from collection, speci...

Waste characterization emanated from kaolin submitted the improvement to process hydrocycloning; Caracterizacao do residuo provindo do beneficiamento do caulim submetido ao processo de hidrociclonagem

Energy Technology Data Exchange (ETDEWEB)

Barbosa Neto, M.C.; Nunes, A.S.; Caetano, A.L.A.; Marques, V.C.; Macedo, D.A.; Ferreira, H.S.; Dutra, R.P.S., E-mail: netobarbosa.2@gmail.com [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

2016-07-01

The hydrocyclones are equipment commonly used for separation of particles by size. The resulting material of this process usually presents different characteristics of the material, which was not subjected to treatment. Therefore, a study of the waste characteristics derived from kaolin processing submitted to hydrocycloning process compared to the same residue without going through the process was executed. The different samples were characterized by X-ray diffraction, X-ray fluorescence, particle size analysis and thermal analysis. The results indicate that the hydrocycloning not modify the mineralogical structure nor chemical material. The particle size analysis identified that the fine fraction, resulting from the process, presented particle size lower than the reference material. (author)

Preparation and characterization of ZnO microfiltration membrane and its support using kaolin (DD3 and CaCO3

Directory of Open Access Journals (Sweden)

B. Boudaira

Full Text Available Abstract The objective of the present paper was to prepare a ceramic support with membrane. Tubular ceramic supports prepared from kaolin (DD3 and calcium carbonate with 6 and 10 mm inner and outer diameters, respectively, were extruded and sintered at 1200 °C. It has been found that sintered supports had interesting characteristics: average pore size of about 5µm, porosity of about 50%, and monomodal pore size distribution. This support was used to be substrate for a membrane layer of microfiltration. This membrane layer was elaborated from zinc oxide, using slip casting technique. The specimens were subsequently sintered at 1000 °C. The microstructure and porosity as well as the permeability have also been studied. It has been found that the average pore size was about 1.2µm, the layer thickness was ~33µm, and the water permeability measured was about 880 L.h-1.m-2.bar-1.

Soft rot erwiniae: from genes to genomes.

Science.gov (United States)

Toth, Ian K; Bell, Kenneth S; Holeva, Maria C; Birch, Paul R J

2003-01-01

SUMMARY The soft rot erwiniae, Erwinia carotovora ssp. atroseptica (Eca), E. carotovora ssp. carotovora (Ecc) and E. chrysanthemi (Ech) are major bacterial pathogens of potato and other crops world-wide. We currently understand much about how these bacteria attack plants and protect themselves against plant defences. However, the processes underlying the establishment of infection, differences in host range and their ability to survive when not causing disease, largely remain a mystery. This review will focus on our current knowledge of pathogenesis in these organisms and discuss how modern genomic approaches, including complete genome sequencing of Eca and Ech, may open the door to a new understanding of the potential subtlety and complexity of soft rot erwiniae and their interactions with plants. The soft rot erwiniae are members of the Enterobacteriaceae, along with other plant pathogens such as Erwinia amylovora and human pathogens such as Escherichia coli, Salmonella spp. and Yersinia spp. Although the genus name Erwinia is most often used to describe the group, an alternative genus name Pectobacterium was recently proposed for the soft rot species. Ech mainly affects crops and other plants in tropical and subtropical regions and has a wide host range that includes potato and the important model host African violet (Saintpaulia ionantha). Ecc affects crops and other plants in subtropical and temperate regions and has probably the widest host range, which also includes potato. Eca, on the other hand, has a host range limited almost exclusively to potato in temperate regions only. Disease symptoms: Soft rot erwiniae cause general tissue maceration, termed soft rot disease, through the production of plant cell wall degrading enzymes. Environmental factors such as temperature, low oxygen concentration and free water play an essential role in disease development. On potato, and possibly other plants, disease symptoms may differ, e.g. blackleg disease is associated

Preparação e caracterização de materiais compósitos SiC/caulim/Al via "squeeze-casting" Preparation and characterization of SiC/kaolin/Al composite materials by squeeze- casting

Directory of Open Access Journals (Sweden)

M. Freitas

2009-09-01

manufacturing these composites is the process of metal casting infiltration under pressure called squeeze-casting. This process offers some advantages, such as ease of producing the composite, low cost and ability to form network structures. In this work were produced and characterized Al-SiC composites, with concentrations in kaolin ranging between 10 and 50% in place to SiC majority phase. The ceramic pre-forms were produced to controlling the fraction of the size SiC/kaolin for better infiltration. These pre-forms after sintering at 1100 ºC/1 h resulted highly porous, and the porosity increased with the increase of kaolin in place to SiC particles. XRD analysis showed the existence of quartz particles beyond the SiC phase. During the infiltration and heat treatment process, the liquid aluminum reacted preferably with quartz and other aluminosilicates particles of the pre-form reducing them, precipitating alumina and silicon in the microstructure, which also presented aluminum in excess that not reacted in the process. The silica and silicates of pre-form, reacted preferably with the aluminum, preventing the formation of Al4C3 phase, which is highly hygroscopic and causes the composite degradation. Depending on the composition, the SiC - kaolin - Al composite developed in this work, can be used in applications involving high bending mechanical resistance (240 to 300 MPa, low density and hardness surface between 180 and 380 kgf/mm².

Evaluating Six Soft Approaches

DEFF Research Database (Denmark)

Sørensen, Lene Tolstrup; Valqui Vidal, René Victor

2008-01-01

's interactive planning principles to be supported by soft approaches in carrying out the principles in action. These six soft approaches are suitable forsupporting various steps of the strategy development and planning process. These are the SWOT analysis, the Future Workshop, the Scenario methodology......, Strategic Option Development and Analysis, Strategic Choice Approach and Soft Systems Methodology. Evaluations of each methodology are carried out using a conceptual framework in which the organisation, the result, the process and the technology of the specific approach are taken into consideration. Using...

Evaluating six soft approaches

DEFF Research Database (Denmark)

Sørensen, Lene Tolstrup; Vidal, Rene Victor Valqui

2008-01-01

's interactive planning principles to be supported by soft approaches in carrying out the principles in action. These six soft approaches are suitable forsupporting various steps of the strategy development and planning process. These are the SWOT analysis, the Future Workshop, the Scenario methodology......, Strategic Option Development and Analysis, Strategic Choice Approach and Soft Systems Methodology. Evaluations of each methodology are carried out using a conceptual framework in which the organisation, the result, the process and the technology of the specific approach are taken into consideration. Using...

Applications of Soft Sets in -Algebras

Directory of Open Access Journals (Sweden)

N. O. Alshehri

2013-01-01

Full Text Available In 1999, Molodtsov introduced the concept of soft set theory as a general mathematical tool for dealing with uncertainty and vagueness. In this paper, we apply the concept of soft sets to K-algebras and investigate some properties of Abelian soft K-algebras. We also introduce the concept of soft intersection K-algebras and investigate some of their properties.

Transient soft X-ray sources

International Nuclear Information System (INIS)

Hayakawa, S.; Murakami, T.; Nagase, F.; Tanaka, Y.; Yamashita, K.

1976-01-01

A rocket observation of cosmic soft X-rays suggests the existence of transient, recurrent soft X-ray sources which are found variable during the flight time of the rocket. Some of the soft X-ray sources thus far reported are considered to be of this time. These sources are listed and their positions are shown. (Auth.)

On Neutrosophic Soft Topological Space

Directory of Open Access Journals (Sweden)

Tuhin Bera

2018-03-01

Full Text Available In this paper, the concept of connectedness and compactness on neutrosophic soft topological space have been introduced along with the investigation of their several characteristics. Some related theorems have been established also. Then, the notion of neutrosophic soft continuous mapping on a neutrosophic soft topological space and it’s properties are developed here.

Mineralogical characterization and beneficiation study of kaolin from Equador (RN) and Junco do Serido (PB) to increase the brightness index; Caracterizacao mineralogica e estudo do beneficiamento do caulim de Equador (RN) e Junco do Serido (PB) para elevacao do indice de alvura

Energy Technology Data Exchange (ETDEWEB)

Campos, V.M.J.S.; Bertolino, L.C., E-mail: vcampos@cetem.gov.br, E-mail: lcbertolino@cetem.gov.br [Centro de Tecnologia Minearal (CETEM), Rio de Janeiro, RJ (Brazil). Setor de Caracterizacao Tecnologica; Alves, O.C., E-mail: odivaldocambraia@id.uff.br [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Instituto de Quimica

2017-07-15

Kaolin is a rock composed mainly of kaolinite. It is used in many industrial segments, such as paper and ceramics. However, for these uses it is necessary to submit the ore to appropriate beneficiation, which generally involves magnetic separation and chemical bleaching, aiming to remove iron oxide and hydroxide, raising brightness index. This work reports the mineralogical characterization and analysis of the beneficiation of three samples of kaolin, two from Equador (Rio Grande do Norte - RN) and the third from Junco do Serido (Paraiba - PB). The samples were submitted to granulometric classification in sieve of 44 μm, magnetic separation in a magnetic induction of 14000 gauss, and chemical bleaching with sodium dithionite during 240 min. The processes were divided into two beneficiation routes. X-ray diffraction, chemical analysis by X-ray fluorescence and scanning electron microscopy were used for mineralogical characterization of the ore and measurement of the brightness index, while electron paramagnetic resonance was applied to study the variation of iron oxides and hydroxides during beneficiation. The results indicate that just 30 min of chemical bleaching without magnetic separation was sufficient to increase the brightness index from 78.2 to 90.2% and from 91.3 to 95.7% in the two samples from Equador (RN) and from 86.9 to 90.4% in the sample from Junco do Serido (PB). The magnetic separation, although causing a small increase in the brightness index, was inefficient for removal of iron oxides and hydroxides. The results indicated no need for using magnetic separation in plants for beneficiation of kaolin from these two locations, providing the reduction of production costs allowing better exploitation of the ore. (author)

Evaluating six soft approaches

DEFF Research Database (Denmark)

Sørensen, Lene; Vidal, Rene Victor Valqui

2006-01-01

’s interactive planning principles to be supported by soft approaches in carrying out the principles in action. These six soft approaches are suitable for supporting various steps of the strategy development and planning process. These are the SWOT analysis, the Future Workshop, the Scenario methodology......, Strategic Option Development and Analysis, Strategic Choice Approach and Soft Systems Methodology. Evaluations of each methodology are carried out using a conceptual framework in which the organisation, the result, the process and the technology of the specific approach are taken into consideration. Using...

Soft, Embodied, Situated & Connected

DEFF Research Database (Denmark)

Tomico, Oscar; Wilde, Danielle

2015-01-01

Soft wearables include clothing and textile-based accessories that incorporate smart textiles and soft electronic interfaces to enable responsive and interactive experiences. When designed well, they leverage the cultural, sociological and material qualities of textiles, fashion and dress; divers...

Soft, embodied, situated & connected

NARCIS (Netherlands)

Tomico Plasencia, O.; Wilde, D.

2015-01-01

Soft wearables include clothing and textile-based accessories that incorporate smart textiles and soft electronic interfaces to enable responsive and interactive experiences. When designed well, they leverage the cultural, sociological and material qualities of textiles, fashion and dress; diverse

Identifying Determinants of Organizational Development as the Key Developers of Employee Soft Skill

Directory of Open Access Journals (Sweden)

Shahjahan Laghari

2016-10-01

Full Text Available The purpose of this article is to identify the determinants of organizational development as the key developers of employee soft skills. Various studies have been taken where determinants of organizational development defining soft skills in employees are discussed. However, the current study is different in Pakistani industry context as the link was missing about the determinants of organizational development which in synchronized way help in developing soft skills in employees of firm. This research uses explanatory approach; incorporating secondary data extracted under the light of existing school of thoughts paired with quantification through data collected from respondents in Pakistani corporate sector. Hypotheses are tested using structural equation model (SEM technique. Results This research showed an affirmative link between determinants of organizational development and development of soft skills in employees. Finally, the study proposes enriching insights on few missing links that can be researched and triggered achieving maximized outcomes.

The study on facial soft tissue thickness using Han population in Xinjiang.

Science.gov (United States)

Wang, Jierui; Zhao, Xi; Mi, Congbo; Raza, Iqbal

2016-09-01

Facial profile is an important aspect in physical anthropology, forensic science, and cosmetic research. Thus, facial soft tissue measurement technology plays a significant role in facial restoration. A considerable amount of work has investigated facial soft tissue thickness, which significantly varies according to gender, age, and race. However, only few studies have considered the nutritional status of the investigated individuals. Moreover, no sufficient research among Chinese ethnic groups, particularly Xinjiang population in China, is currently available. Hence, the current study investigated the adaptability of facial soft tissue to the underlying hard tissue among young adults of Han population in Xinjiang, China; the analysis was performed on the basis of gender, skeletal class, and body mass index (BMI). Measurements were obtained from the lateral cephalometric radiographs of 256 adults aged 18-26 years old. Differences in soft tissue thickness were observed between genders and among skeletal classes. With regard to gender, significant differences in soft tissue thickness were found at rhinion, glabella, subnasale, stomion, labrale superius, pogonion, and gnathion among different BMI groups. Thus, nutritional status should be considered when reconstructing an individual's facial profile. Results showed that the thinnest and thickest craniofacial soft tissues existed in rhinion and lip regions, respectively. Overall, this research provides valuable data for forensic facial reconstruction and identification of young adults in Xinjiang, China. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Buckling of paramagnetic chains in soft gels

Science.gov (United States)

Huang, Shilin; Pessot, Giorgio; Cremer, Peet; Weeber, Rudolf; Holm, Christian; Nowak, Johannes; Odenbach, Stefan; Menzel, Andreas M.; Auernhammer, Günter K.

We study the magneto-elastic coupling behavior of paramagnetic chains in soft polymer gels exposed to external magnetic fields. To this end, a laser scanning confocal microscope is used to observe the morphology of the paramagnetic chains together with the deformation field of the surrounding gel network. The paramagnetic chains in soft polymer gels show rich morphological shape changes under oblique magnetic fields, in particular a pronounced buckling deformation. The details of the resulting morphological shapes depend on the length of the chain, the strength of the external magnetic field, and the modulus of the gel. Based on the observation that the magnetic chains are strongly coupled to the surrounding polymer network, a simplified model is developed to describe their buckling behavior. A coarse-grained molecular dynamics simulation model featuring an increased matrix stiffness on the surfaces of the particles leads to morphologies in agreement with the experimentally observed buckling effects.

Soft tissue modelling with conical springs.

Science.gov (United States)

Omar, Nadzeri; Zhong, Yongmin; Jazar, Reza N; Subic, Aleksandar; Smith, Julian; Shirinzadeh, Bijan

2015-01-01

This paper presents a new method for real-time modelling soft tissue deformation. It improves the traditional mass-spring model with conical springs to deal with nonlinear mechanical behaviours of soft tissues. A conical spring model is developed to predict soft tissue deformation with reference to deformation patterns. The model parameters are formulated according to tissue deformation patterns and the nonlinear behaviours of soft tissues are modelled with the stiffness variation of conical spring. Experimental results show that the proposed method can describe different tissue deformation patterns using one single equation and also exhibit the typical mechanical behaviours of soft tissues.

PREFACE: International Symposium on Non-Equilibrium Soft Matter 2010 International Symposium on Non-Equilibrium Soft Matter 2010

Science.gov (United States)

Kawakatsu, T.; Matsuyama, A.; Ohta, T.; Tanaka, H.; Tanaka, S.

2011-07-01

, Culture, Sports, Science and Technology (MEXT) of Japan. We thank those who contributed to this symposium as well as members of the 'Soft Matter Physics' project for their valuable discussions and collaborations. Non-equilibrium soft matter contents Insights on raft behavior from minimal phenomenological models G Garbès Putzel and M Schick Dynamical membrane curvature instability controlled by intermonolayer friction Anne-Florence Bitbol, Jean-Baptiste Fournier, Miglena I Angelova and Nicolas Puff Numerical investigations of the dynamics of two-component vesicles Takashi Taniguchi, Miho Yanagisawa and Masayuki Imai Asymmetric distribution of cone-shaped lipids in a highly curved bilayer revealed by a small angle neutron scattering technique Y Sakuma, N Urakami, T Taniguchi and M Imai Hydration, phase separation and nonlinear rheology of temperature-sensitive water-soluble polymers Fumihiko Tanaka, Tsuyoshi Koga, Isamu Kaneda and Françoise M Winnik Morphology and rheology of an immiscible polymer blend subjected to a step electric field under shear flow H Orihara, Y Nishimoto, K Aida, Y H Na, T Nagaya and S Ujiie Surfactant-induced friction reduction for hydrogels in the boundary lubrication regime Kosuke Kamada, Hidemitsu Furukawa, Takayuki Kurokawa, Tomohiro Tada, Taiki Tominaga, Yukihiro Nakano and Jian Ping Gong Fabrication and structural analysis of polyrotaxane fibers and films Yasuhiro Sakai, Kentaro Ueda, Naoya Katsuyama, Koji Shimizu, Shunya Sato, Jun Kuroiwa, Jun Araki, Akira Teramoto, Koji Abe, Hideaki Yokoyama and Kohzo Ito Micellization kinetics of diblock copolymers in a homopolymer matrix: a self-consistent field study Raghuram Thiagarajan and David C Morse Hierarchical self-assembly of two-length-scale multiblock copolymers Gerrit ten Brinke, Katja Loos, Ivana Vukovic and Gerrit Gobius du Sart Kaleidoscopic morphologies from ABC star-shaped terpolymers Yushu Matsushita, Kenichi Hayashida, Tomonari Dotera and Atsushi Takano Direct and inverted nematic

Analysis and optimization of flocculation activity and turbidity reduction in kaolin suspension using pectin as a biopolymer flocculant.

Science.gov (United States)

Ho, Y C; Norli, I; Alkarkhi, Abbas F M; Morad, N

2009-01-01

The performance of pectin in turbidity reduction and the optimum condition were determined using Response Surface Methodology (RSM). The effect of pH, cation's concentration, and pectin's dosage on flocculating activity and turbidity reduction was investigated at three levels and optimized by using Box-Behnken Design (BBD). Coagulation and flocculation process were assessed with a standard jar test procedure with rapid and slow mixing of a kaolin suspension (aluminium silicate), at 150 rpm and 30 rpm, respectively, in which a cation e.g. Al(3+), acts as coagulant, and pectin acts as the flocculant. In this research, all factors exhibited significant effect on flocculating activity and turbidity reduction. The experimental data and model predictions well agreed. From the 3D response surface graph, maximum flocculating activity and turbidity reduction are in the region of pH greater than 3, cation concentration greater than 0.5 mM, and pectin dosage greater than 20 mg/L, using synthetic turbid wastewater within the range. The flocculating activity for pectin and turbidity reduction in wastewater is at 99%.

Mapping on complex neutrosophic soft expert sets

Science.gov (United States)

Al-Quran, Ashraf; Hassan, Nasruddin

2018-04-01

We introduce the mapping on complex neutrosophic soft expert sets. Further, we investigated the basic operations and other related properties of complex neutrosophic soft expert image and complex neutrosophic soft expert inverse image of complex neutrosophic soft expert sets.

FPGAs and parallel architectures for aerospace applications soft errors and fault-tolerant design

CERN Document Server

Rech, Paolo

2016-01-01

This book introduces the concepts of soft errors in FPGAs, as well as the motivation for using commercial, off-the-shelf (COTS) FPGAs in mission-critical and remote applications, such as aerospace.  The authors describe the effects of radiation in FPGAs, present a large set of soft-error mitigation techniques that can be applied in these circuits, as well as methods for qualifying these circuits under radiation.  Coverage includes radiation effects in FPGAs, fault-tolerant techniques for FPGAs, use of COTS FPGAs in aerospace applications, experimental data of FPGAs under radiation, FPGA embedded processors under radiation, and fault injection in FPGAs. Since dedicated parallel processing architectures such as GPUs have become more desirable in aerospace applications due to high computational power, GPU analysis under radiation is also discussed. ·         Discusses features and drawbacks of reconfigurability methods for FPGAs, focused on aerospace applications; ·         Explains how radia...

For production of ceramic plates coating using waste kaolin, granite and marble; Caracterizacao de residuos de caulim, granito e marmore para uso em massas ceramicas

Energy Technology Data Exchange (ETDEWEB)

Sales, J.L.; Morais, C.R.S.; Lima, L.M.R.; Altidis, M.E.D., E-mail: josyanne27@yahoo.com.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

2011-07-01

The objective is to benefit and characterize waste from kaolin, marble and granite studying their thermal properties and spectroscopic in employment perspective on ceramic production of flooring boards. The residues were benefited through the process of dry grinding mill in greyhounds and passed through sieve 0.074 mm (ABNT No. 200), observing their suitability for the formulation of ceramic pastes. Tests were performed physicochemical characterization (particle size analysis, X-ray fluorescence and X-ray diffraction) and thermal (differential thermal analysis and thermogravimetry). The results showed that these residues showed satisfactory properties for the purpose for which it proposes, and contribute to reducing environmental impacts, allowing the reuse of the production of ceramic plates (author)

Soft Skills in Higher Education: Importance and Improvement Ratings as a Function of Individual Differences and Academic Performance

Science.gov (United States)

Chamorro-Premuzic, Tomas; Arteche, Adriane; Bremner, Andrew J.; Greven, Corina; Furnham, Adrian

2010-01-01

Three UK studies on the relationship between a purpose-built instrument to assess the importance and development of 15 "soft skills" are reported. "Study 1" (N = 444) identified strong latent components underlying these soft skills, such that differences "between-skills" were over-shadowed by differences…

Soft-tissue tension total knee arthroplasty.

Science.gov (United States)

Asano, Hiroshi; Hoshino, Akiho; Wilton, Tim J

2004-08-01

It is far from clear how best to define the proper strength of soft-tissue tensioning in total knee arthroplasty (TKA). We attached a torque driver to the Monogram balancer/tensor device and measured soft-tissue tension in full extension and 90 degrees flexion during TKA. In our surgical procedure, when we felt proper soft-tissue tension was being applied, the mean distraction force was noted to be 126N in extension and 121N in flexion. There was no significant correlation between soft-tissue tension and the postoperative flexion angle finally achieved. To the best of our knowledge, this is the first study to assess the actual distraction forces in relation to soft-tissue tension in TKA. Further study may reveal the most appropriate forces to achieve proper soft-tissue tension in the wide variety of circumstances presenting at knee arthroplasty.

The effects of LIPUS on soft-tissue healing: a review of literature.

Science.gov (United States)

Khanna, Anil; Nelmes, Richard T C; Gougoulias, Nikolaos; Maffulli, Nicola; Gray, Jim

2009-01-01

Ultrasound is widely used for imaging purposes and as an adjunct to physiotherapy. Low-intensity pulsed ultrasound (LIPUS), having removed the thermal component found at higher intensities, is used to improve bone healing. However, its potential role in soft-tissue healing is still under investigation. We searched on Medline using the keywords: low-intensity pulsed ultrasound, LIPUS and LIPUS and soft-tissue healing. Thirty-two suitable articles were identified. Research, mainly pre-clinical, so far has shown encouraging result, with LIPUS able to promote healing in various soft tissues such as cartilage, inter-vertebral disc, etc. The effect on the bone-tendon junction, however, is primarily on bone. The role of LIPUS in treating tendinopathies is questionable. Adequately powered human studies with standardisation of intensities and dosages of LIPUS for each target tissue are needed.

Planar Elongation Measurements on Soft Elastomers

DEFF Research Database (Denmark)

Jensen, Mette Krog; Skov, Anne Ladegaard; Rasmussen, Henrik K.

2009-01-01

A new fixture to the filament stretch rheometer (FSR) has been developed to measure planar elongation of soft polymeric networks. To validate this new technique, soft polymeric networks of poly(propyleneoxide) (PPO) were investigated during deformation.......A new fixture to the filament stretch rheometer (FSR) has been developed to measure planar elongation of soft polymeric networks. To validate this new technique, soft polymeric networks of poly(propyleneoxide) (PPO) were investigated during deformation....

Success of Chemotherapy in Soft Matter

OpenAIRE

Trifonova, I.; Kurteva, G.; Stefanov, S. Z.

2014-01-01

The success of chemotharapy in soft matter as a survival is found in the paper. Therefore, it is found the analogous tumor stretching force in soft matter; ultrasonography is performed for this tumor; restoration in soft matter with such a tumor is found; Bayes estimate of the probability of chemotherapy success is derived from the transferred chemical energy and from soft matter entropy; survival probability is juxtaposed to this probability of success.

Soft Tissue Sarcoma—Health Professional Version

Science.gov (United States)

Soft tissue sarcomas are malignant tumors that arise in any of the mesodermal tissues of the extremities, trunk and retroperitoneum, or head and neck. Soft tissue sarcomas may be heterogeneous. Find evidence-based information on soft tissue sarcoma treatment and research.

Synthesis of Nano- alumina Powder from Impure Kaolin and its Application for Arsenite Removal from Aqueous Solutions

Directory of Open Access Journals (Sweden)

Ahmad Khodadadi Darban

2013-07-01

Full Text Available Adsorption is considered a cost-effective procedure, safer to handle with high removal efficiency. Activated alumina is the most commonly used adsorbent for the removal of arsenic from aqueous solutions. However, activated alumina has a low adsorption capacity and acts kinetically in a slow manner. An ideal adsorbent should have a high surface area, physical and/or chemical stability and be inexpensive. To meet this requirement, nanomeso porous γ-alumina with a high surface area (201.53 m2/g and small particle size (22–36 nm was prepared from inexpensive kaolin as the raw material, by precipitation method. The research results showed that adsorbent has the high adsorption capacity (for initial arsenite concentration up to 10 mg/L, in which 97.65% recovery was achieved. Optimal experimental conditions including pH, initial arsenite concentration and contact time were determined. Langmuir, Freundlich and Dubinin– Radushkevich isotherm models were applied to analyze the experimental data. The best interpretation for the experimental data was given by Langmuir adsorption isotherm equation and the maximum arsenite adsorbed by synthesized nano γ–alumina (qe was found to be 40 (mg/g.

Radiosensitivity of soft tissue sarcomas

International Nuclear Information System (INIS)

Hirano, Toru; Iwasaki, Katsuro; Suzuki, Ryohei; Monzen, Yoshio; Hombo, Zenichiro

1989-01-01

The correlation between the effectiveness of radiation therapy and the histology of soft tissue sarcomas was investigated. Of 31 cases with a soft tissue sarcoma of an extremity treated by conservative surgery and postoperative radiation of 3,000-6,000 cGy, local recurrence occurred in 12; 5 out of 7 synovial sarcomas, 4 of 9 MFH, one of 8 liposarcomas, none of 4 rhabdomyosarcomas and 2 of 3 others. As for the histological subtyping, the 31 soft tissue sarcomas were divided into spindle cell, pleomorphic cell, myxoid and round cell type, and recurrence rates were 75%, 33.3%, 16.7% and 0%, respectively. From the remarkable difference in recurrent rate, it was suggested that round cell and myxoid type of soft tissue sarcomas showed a high radiosensitivity compared to the spindle cell type with low sensitivity. Clarifying the degree of radiosensitivity is helpful in deciding on the management of limb salvage in soft tissue sarcomas of an extremity. (author)

Architecture design for soft errors

CERN Document Server

Mukherjee, Shubu

2008-01-01

This book provides a comprehensive description of the architetural techniques to tackle the soft error problem. It covers the new methodologies for quantitative analysis of soft errors as well as novel, cost-effective architectural techniques to mitigate them. To provide readers with a better grasp of the broader problem deffinition and solution space, this book also delves into the physics of soft errors and reviews current circuit and software mitigation techniques.

Soft behavior of a closed massless state in superstring and universality in the soft behavior of the dilaton

Energy Technology Data Exchange (ETDEWEB)

Vecchia, Paolo Di [The Niels Bohr Institute, University of Copenhagen,Blegdamsvej 17, DK-2100 Copenhagen Ø (Denmark); Nordita, KTH Royal Institute of Technology and Stockholm University, Roslagstullsbacken 23, SE-10691 Stockholm (Sweden); Marotta, Raffaele [Istituto Nazionale di Fisica Nucleare, Sezione di Napoli,Complesso Universitario di Monte S. Angelo ed. 6, via Cintia, 80126, Napoli (Italy); Mojaza, Matin [Max-Planck-Institut für Gravitationsphysik, Albert-Einstein-Institut, Am Mühlenberg 1, 14476 Potsdam (Germany)

2016-12-06

We consider the tree-level scattering amplitudes in the NS-NS (Neveu-Schwarz) massless sector of closed superstrings in the case where one external state becomes soft. We compute the amplitudes generically for any number of dimensions and any number and kind of the massless closed states through the subsubleading order in the soft expansion. We show that, when the soft state is a graviton or a dilaton, the full result can be expressed as a soft theorem factorizing the amplitude in a soft and a hard part. This behavior is similar to what has previously been observed in field theory and in the bosonic string. Differently from the bosonic string, the supersymmetric soft theorem for the graviton has no string corrections at subsubleading order. The dilaton soft theorem, on the other hand, is found to be universally free of string corrections in any string theory.

Soft behavior of a closed massless state in superstring and universality of the soft behavior of the dilaton

DEFF Research Database (Denmark)

di Vecchia, Paolo; Marotta, Raffaele; Mojaza, Matin

2016-01-01

We consider the tree-level scattering amplitudes in the NS-NS (Neveu-Schwarz) massless sector of closed superstrings in the case where one external state becomes soft. We compute the amplitudes generically for any number of dimensions and any number and kind of the massless closed states through...... the subsubleading order in the soft expansion. We show that, when the soft state is a graviton or a dilaton, the full result can be expressed as a soft theorem factorizing the amplitude in a soft and a hard part. This behavior is similar to what has previously been observed in field theory and in the bosonic string....... Differently from the bosonic string, the supersymmetric soft theorem for the graviton has no string corrections at subsubleading order. The dilaton soft theorem, on the other hand, is found to be universally free of string corrections in any string theory....

On single and double soft behaviors in NLSM

International Nuclear Information System (INIS)

Du, Yi-Jian; Luo, Hui

2015-01-01

In this paper, we study the single and double soft behaviors of tree level off-shell currents and on-shell amplitudes in nonlinear sigma model (NLSM). We first propose and prove the leading soft behavior of the tree level currents with a single soft particle. In the on-shell limit, this single soft emission becomes the Adler’s zero. Then we establish the leading and subleading soft behaviors of tree level currents with two adjacent soft particles. With a careful analysis of the on-shell limit, we obtain the double soft behaviors of on-shell amplitudes where the two soft particles are adjacent to each other. By applying Kleiss-Kuijf (KK) relation, we further obtain the leading and subleading behaviors of amplitudes with two nonadjacent soft particles.

Centrifugal forming and mechanical properties of silicone-based elastomers for soft robotic actuators

Science.gov (United States)

Kulkarni, Parth

This thesis describes the centrifugal forming and resulting mechanical properties of silicone-based elastomers for the manufacture of soft robotic actuators. This process is effective at removing bubbles that get entrapped within 3D-printed, enclosed molds. Conventional methods for rapid prototyping of soft robotic actuators to remove entrapped bubbles typically involve degassing under vacuum, with open-faced molds that limit the layout of formed parts to raised 2D geometries. As the functionality and complexity of soft robots increase, there is a need to mold complete 3D structures with controlled thicknesses or curvatures on multiples surfaces. In addition, characterization of the mechanical properties of common elastomers for these soft robots has lagged the development of new designs. As such, relationships between resulting material properties and processing parameters are virtually non-existent. One of the goals of this thesis is to provide guidelines and physical insights to relate the design, processing conditions, and resulting properties of soft robotic components to each other. Centrifugal forming with accelerations on the order of 100 g's is capable of forming bubble-free, true 3D components for soft robotic actuators, and resulting demonstrations in this work include an aquatic locomotor, soft gripper, and an actuator that straightens when pressurized. Finally, this work shows that the measured mechanical properties of 3D geometries fabricated within enclosed molds through centrifugal forming possess comparable mechanical properties to vacuumed materials formed from open-faced molds with raised 2D features.

Soft Space Planning in Cities unbound

DEFF Research Database (Denmark)

Olesen, Kristian

This paper analyses contemporary experiments of building governance capacity in new soft spaces in Denmark through processes of spatial strategy-making. The paper argues that new soft spaces are emerging in Danish spatial planning, which set out to promote more effective forms of strategic spatial...... planning, and how their obsession with promoting economic development at the expense of wider planning responsibilities support contemporary neoliberal transformations of strategic spatial planning....... planning. The Danish case of soft space planning demonstrates how Danish soft spaces at subnational scales fail to fill in the gaps between formal planning structures and provide the glue that binds formal scales of planning together as promised in the soft space literature. This raises a number...

Small scale soft x-ray lasers

International Nuclear Information System (INIS)

Skinner, C.H.; DiCicco, D.S.; Kim, D.; Voorhees, D.; Suckewer, S.

1990-01-01

The widespread application of soft x-ray laser technology is contingent on the development of small scale soft x-ray lasers that do not require large laser facilities. Progress in the development of soft x-ray lasers pumped by a Nd laser of energy 6-12J is reported below. Application of an existing soft x-ray laser to x-ray microscopy has begun. A soft x-ray laser of output energy 1-3 mJ at 18,2 nm has been used to record high resolution images of biological specimens. The contact images were recorded on photoresist which was later viewed in a scanning electron microscope. The authors present a composite optical x-ray laser microscope design

Soft Decision Analyzer

Science.gov (United States)

Lansdowne, Chatwin; Steele, Glen; Zucha, Joan; Schlesinger, Adam

2013-01-01

We describe the benefit of using closed-loop measurements for a radio receiver paired with a counterpart transmitter. We show that real-time analysis of the soft decision output of a receiver can provide rich and relevant insight far beyond the traditional hard-decision bit error rate (BER) test statistic. We describe a Soft Decision Analyzer (SDA) implementation for closed-loop measurements on single- or dual- (orthogonal) channel serial data communication links. The analyzer has been used to identify, quantify, and prioritize contributors to implementation loss in live-time during the development of software defined radios. This test technique gains importance as modern receivers are providing soft decision symbol synchronization as radio links are challenged to push more data and more protocol overhead through noisier channels, and software-defined radios (SDRs) use error-correction codes that approach Shannon's theoretical limit of performance.

Dual constituent-exchange dynamics in soft and hard hadronic processes

International Nuclear Information System (INIS)

Akkelin, S.V.; Kobylinskij, N.A.; Martynov, E.S.; Shelest, V.P.

1987-01-01

A possibility to match the dual theory of soft hadronic processes to the dimensional counting rules for hard processes has been studied. This aim is shown to be attained within the framework of the dual analytical model under certain conditions on the shape and parameters of the Regge trajectories

Soft pneumatic grippers embedded with stretchable electroadhesion

Science.gov (United States)

Guo, J.; Elgeneidy, K.; Xiang, C.; Lohse, N.; Justham, L.; Rossiter, J.

2018-05-01

Current soft pneumatic grippers cannot robustly grasp flat materials and flexible objects on curved surfaces without distorting them. Current electroadhesive grippers, on the other hand, are difficult to actively deform to complex shapes to pick up free-form surfaces or objects. An easy-to-implement PneuEA gripper is proposed by the integration of an electroadhesive gripper and a two-fingered soft pneumatic gripper. The electroadhesive gripper was fabricated by segmenting a soft conductive silicon sheet into a two-part electrode design and embedding it in a soft dielectric elastomer. The two-fingered soft pneumatic gripper was manufactured using a standard soft lithography approach. This novel integration has combined the benefits of both the electroadhesive and soft pneumatic grippers. As a result, the proposed PneuEA gripper was not only able to pick-and-place flat and flexible materials such as a porous cloth but also delicate objects such as a light bulb. By combining two soft touch sensors with the electroadhesive, an intelligent and shape-adaptive PneuEA material handling system has been developed. This work is expected to widen the applications of both soft gripper and electroadhesion technologies.

Soft timing closure for soft programmable logic cores: The ARGen approach

OpenAIRE

Bollengier , Théotime; Lagadec , Loïc; Najem , Mohamad; Le Lann , Jean-Christophe; Guilloux , Pierre

2017-01-01

International audience; Reconfigurable cores support post-release updates which shortens time-to-market while extending circuits’ lifespan. Reconfigurable cores can be provided as hard cores (ASIC) or soft cores (RTL). Soft reconfigurable cores outperform hard reconfigurable cores by preserving the ASIC synthesis flow, at the cost of lowering scalability but also exacerbating timing closure issues. This article tackles these two issues and introduces the ARGen generator that produces scalable...

Neutrosophic Parameterized Soft Relations and Their Applications

Directory of Open Access Journals (Sweden)

Irfan Deli

2014-06-01

Full Text Available The aim of this paper is to introduce the concept of relation on neutrosophic parameterized soft set (NP- soft sets theory. We have studied some related properties and also put forward some propositions on neutrosophic parameterized soft relation with proofs and examples. Finally the notions of symmetric, transitive, reflexive, and equivalence neutrosophic parameterized soft set relations have been established in our work. Finally a decision making method on NP-soft sets is presented.

Hard And Soft QCD Physics In ATLAS

Directory of Open Access Journals (Sweden)

Adomeit Stefanie

2014-04-01

Full Text Available Hard and soft QCD results using proton-proton collisions recorded with the ATLAS detector at the LHC are reported. Charged-particle distributions and forward-backward correlations have been studied in low-luminosity minimum bias data taken at centre-of-mass energies of √s = 0.9, 2.36 and 7 TeV. Recent measurements on underlying event characteristics using charged-particle jets are also presented. The results are tested against various phenomenological soft QCD models implemented in Monte-Carlo generators. A summary of hard QCD measurements involving high transverse momentum jets is also given. Inclusive jet and dijet cross-sections have been measured at a centre-of-mass energy of 7 TeV and are compared to expectations based on NLO pQCD calculations corrected for non-perturbative effects as well as to NLO Monte Carlo predictions. Recent studies exploiting jet substructure techniques to identify hadronic decays of boosted massive particles are reported.

Fabrication of recyclable and durable superhydrophobic materials with wear/corrosion-resistance properties from kaolin and polyvinylchloride

International Nuclear Information System (INIS)

Qu, Mengnan; Liu, Shanshan; He, Jinmei; Feng, Juan; Yao, Yali; Ma, Xuerui; Hou, Lingang; Liu, Xiangrong

2017-01-01

Highlights: • The scraped debris can be recycled and easily reused to fabricate the superhydrophobic materials. • The obtained materials displayed liquid-repellent toward water and several other liquids of daily life. • The superhydrophobic materials can retain excellent chemical stability and mechanical durability after rigorous tests. • This as-prepared material can be regarded as a real superhydrophobic “material”, not just the superhydrophobic “surface”. - Abstract: In this study, mechanically stable and recyclable superhydrophobic materials were prepared from polyvinylchloride (PVC) and kaolin nanoparticles modified by stearic acid using a simple and low-cost drop-coating. The obtained materials displayed liquid-repellent toward water and several other liquids of daily life (such as orange juice, coffee, milk, coca cola and ink). These superhydrophobic materials showed remarkable robustness against sandpaper abrasion, UV-irradiation and ultrasonication test, while retaining its superhydrophobicity even after 60 abrasion cycles loaded of 500 g with sandpaper, 7 days UV-irradiation or 120 min ultrasonication test. The excellent durability against complex conditions was attributed to the hierarchical structure and strong interfacial adhesion of the materials. More significantly, the materials used in the coating could be recycled and reconstructed without losing its superhydrophobicity. The current superhydrophobic materials tolerate rigorous environment, opening a new avenue to a variety of practical applications.

Fabrication of recyclable and durable superhydrophobic materials with wear/corrosion-resistance properties from kaolin and polyvinylchloride

Energy Technology Data Exchange (ETDEWEB)

Qu, Mengnan, E-mail: mnanqu@gmail.com; Liu, Shanshan; He, Jinmei, E-mail: jinmhe@gmail.com; Feng, Juan; Yao, Yali; Ma, Xuerui; Hou, Lingang; Liu, Xiangrong

2017-07-15

Highlights: • The scraped debris can be recycled and easily reused to fabricate the superhydrophobic materials. • The obtained materials displayed liquid-repellent toward water and several other liquids of daily life. • The superhydrophobic materials can retain excellent chemical stability and mechanical durability after rigorous tests. • This as-prepared material can be regarded as a real superhydrophobic “material”, not just the superhydrophobic “surface”. - Abstract: In this study, mechanically stable and recyclable superhydrophobic materials were prepared from polyvinylchloride (PVC) and kaolin nanoparticles modified by stearic acid using a simple and low-cost drop-coating. The obtained materials displayed liquid-repellent toward water and several other liquids of daily life (such as orange juice, coffee, milk, coca cola and ink). These superhydrophobic materials showed remarkable robustness against sandpaper abrasion, UV-irradiation and ultrasonication test, while retaining its superhydrophobicity even after 60 abrasion cycles loaded of 500 g with sandpaper, 7 days UV-irradiation or 120 min ultrasonication test. The excellent durability against complex conditions was attributed to the hierarchical structure and strong interfacial adhesion of the materials. More significantly, the materials used in the coating could be recycled and reconstructed without losing its superhydrophobicity. The current superhydrophobic materials tolerate rigorous environment, opening a new avenue to a variety of practical applications.

Influence of aging on bearing capacity of circular footing resting on soft soil

Directory of Open Access Journals (Sweden)

Mohamed B.D. Elsawy

2013-12-01

Full Text Available Structures constructed on soft soil are considered to be at risk due to its low shear strength and high compressibility. Thus constructed structures on soft soil are designed according to its undrained shear strength, representing the bearing capacity of the shallow foundation in the short term conditions, which varies with time under the applied load. The bearing capacity in short term conditions is limited because of the generation of excess pore water pressure as soon as the initial loads are applied. Hence in this paper, the bearing capacity of shallow foundations on soft soil is studied by varying the time and the applied loads. The shallow foundation is subjected to a series of applied loads and consolidation phases to study the effect of aging. The study is investigated by means of finite element analyses taking account of consolidation processes in the ground, in which the soft soil is modeled using the Soft Soil model. The analysis is performed by finite element package of Plaxis program. The numerical analysis clears that the bearing capacity in the long term conditions is enhanced and has a significant enhancement following each consolidation phase when compared with the short term conditions.

learning and soft skills

DEFF Research Database (Denmark)

Rasmussen, Lauge Baungaard

2000-01-01

Learning of soft skills are becoming more and more necessary due to the complexe development of modern companies and their environments. However, there seems to be a 'gap' between intentions and reality regarding need of soft skills and the possiblities to be educated in this subject in particular...

Effect of sealer coating and storage methods on the surface roughness of soft liners.

Science.gov (United States)

Usta Kutlu, Ilknur; Yanikoğlu, Nuran Dinckal; Kul, Esra; Duymuş, Zeynep Yesïl; Sağsöz, Nurdan Polat

2016-03-01

A soft lining is applied under a removable prosthesis for various reasons. The porosity of the lining material may increase colonization by microorganisms and cause tissue inflammation. The purpose of this in vitro study was to evaluate the effect of sealer coating on the surface roughness of soft lining materials under 4 different conditions. A total of 125 specimens were prepared. One high-temperature silicone-based soft lining material and 2 room-temperature-polymerized soft lining materials (1 silicone-based and 1 methacrylate-based) were used. Twenty-five specimens of each room-temperature soft lining material were coated with 2 layers of surface sealer. Additionally, 5 specimens of each material were stored in either distilled water, Coca-Cola, denture cleanser, saliva, or air. The surface roughness was measured at baseline and after 1, 7, 14, and 28 days. Surface roughness values were analyzed with repeated measures analysis of variance, and the Bonferroni multiple comparison test was performed using time-dependent groups and storage methods. In the time-dependent groups, methacrylate-based sealer-coated soft liners exhibited a significant increase in roughness (1.74-2.09 μm, P.05). Therefore, the sealer coating was not effective in reducing surface roughness. Among the time-dependent storage methods, the denture cleanser exhibited an almost significant increase in roughness (1.83-1.99 μm, P=.054). Coca-Cola and artificial saliva did not show a significant difference (P>.05). However, a significant decrease in roughness was found with distilled water (P=.02) and air (P<.001). Statistically significant differences in surface roughness were found among the different types of soft liners. The sealer coating had no significant effect, and denture cleanser slightly increased the surface roughness. Contrary to expectations, the roughness did not increase in all groups over time. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry

Soft Mobility and Urban Transformation

Directory of Open Access Journals (Sweden)

Rosa Anna La Rocca

2010-04-01

Full Text Available This paper examines some European cases referred to promotion of soft mobility as a new lifestyle aimed to improve benefits on environment and urban liveability. Soft mobility includes any non-motorized transport (human powered mobility. According to this, soft mobility refers to pedestrian, bicycle, roller skate and skateboard transfers. It could be indented as “zeroimpact” mobility too. As a matter of fact, the words to define this way of moving have not been codified yet, therefore mobilitè douce, soft mobility, slow traffic are synonymous in referring mainly to pedestrians and cyclists to indicate alternative to car use. Soft mobility, indeed, can be defined as a special form of sustainable mobility able to optimize urban liveability, by keeping the individual right to move. At present, cities are engaged in defining policies, procedures and interventions to further “slow traffic”, both to relieve the traffic congestion, and to work for regeneration and environmental improvements. This asks for an in-depth cooperation between different political and administrative levels to achieve common objectives of development more attentive to environmental concerns. Despite this increasing attention, the idea of a “network” for soft mobility has not been yet achieved and the supply of integrated facilities and services as an alternative to the car use seems to be still difficult of accomplishment. High disparity characterizes European countries in promoting soft mobility: despite a prolific production of laws and roles referred to emergency of adopting alternative ways of moving to minimize negatives impacts (especially air and noise pollution as very threat to health due to car dependence for urban short distance too. And yet, soft mobility could represent a real occasion of urban and territorial regeneration aimed to rehabilitate some disused paths and routes (greenways. Some successful European cases show how it is possible to

Small metal soft tissue foreign body extraction by using 3D CT guidance: A reliable method

International Nuclear Information System (INIS)

Tao, Kai; Xu, Sen; Liu, Xiao-yan; Liang, Jiu-long; Qiu, Tao; Tan, Jia-nan; Che, Jian-hua; Wang, Zi-hua

2012-01-01

Objective: To introduce a useful and accurate technique for the locating and removal of small metal foreign bodies in the soft tissues. Methods: Eight patients presented with suspected small metal foreign bodies retained in the soft tissues of various body districts. Under local anesthesia, 3–6 pieces of 5 ml syringe needles or 1 ml syringe needles were induced through three different planes around the entry point of the foreign bodies. Using these finders, the small metal FBs were confirmed under 3D CT guidance. Based on the CT findings, the soft tissues were dissected along the path of the closest needle and the FBs were easily found and removed according to the relation with the closest needle finder. Results: Eight metal foreign bodies (3 slices, 3 nails, 1 fish hook, 1 needlepoint) were successfully removed under 3D CT guidance in all patients. The procedures took between 35 min and 50 min and the operation times took between 15 min and 25 min. No complications arose after the treatment. Conclusion: 3D CT-guided technique is a good alternative for the removal of small metal foreign body retained in the soft tissues as it is relatively accurate, reliable, quick, carries a low risk of complications and can be a first-choice procedure for the extraction of small metal foreign body.

Fundamentals of soft robot locomotion

OpenAIRE

Calisti, M.; Picardi, G.; Laschi, C.

2017-01-01

Soft robotics and its related technologies enable robot abilities in several robotics domains including, but not exclusively related to, manipulation, manufacturing, human���robot interaction and locomotion. Although field applications have emerged for soft manipulation and human���robot interaction, mobile soft robots appear to remain in the research stage, involving the somehow conflictual goals of having a deformable body and exerting forces on the environment to achieve locomotion. This p...

Imaging of musculoskeletal soft tissue infections

Energy Technology Data Exchange (ETDEWEB)

Turecki, Marcin B.; Taljanovic, Mihra S.; Holden, Dean A.; Hunter, Tim B.; Rogers, Lee F. [University of Arizona HSC, Department of Radiology, Tucson, AZ (United States); Stubbs, Alana Y. [Southern Arizona VA Health Care System, Department of Radiology, Tucson, AZ (United States); Graham, Anna R. [University of Arizona HSC, Department of Pathology, Tucson, AZ (United States)

2010-10-15

Prompt and appropriate imaging work-up of the various musculoskeletal soft tissue infections aids early diagnosis and treatment and decreases the risk of complications resulting from misdiagnosis or delayed diagnosis. The signs and symptoms of musculoskeletal soft tissue infections can be nonspecific, making it clinically difficult to distinguish between disease processes and the extent of disease. Magnetic resonance imaging (MRI) is the imaging modality of choice in the evaluation of soft tissue infections. Computed tomography (CT), ultrasound, radiography and nuclear medicine studies are considered ancillary. This manuscript illustrates representative images of superficial and deep soft tissue infections such as infectious cellulitis, superficial and deep fasciitis, including the necrotizing fasciitis, pyomyositis/soft tissue abscess, septic bursitis and tenosynovitis on different imaging modalities, with emphasis on MRI. Typical histopathologic findings of soft tissue infections are also presented. The imaging approach described in the manuscript is based on relevant literature and authors' personal experience and everyday practice. (orig.)

Imaging of musculoskeletal soft tissue infections

International Nuclear Information System (INIS)

Turecki, Marcin B.; Taljanovic, Mihra S.; Holden, Dean A.; Hunter, Tim B.; Rogers, Lee F.; Stubbs, Alana Y.; Graham, Anna R.

2010-01-01

Prompt and appropriate imaging work-up of the various musculoskeletal soft tissue infections aids early diagnosis and treatment and decreases the risk of complications resulting from misdiagnosis or delayed diagnosis. The signs and symptoms of musculoskeletal soft tissue infections can be nonspecific, making it clinically difficult to distinguish between disease processes and the extent of disease. Magnetic resonance imaging (MRI) is the imaging modality of choice in the evaluation of soft tissue infections. Computed tomography (CT), ultrasound, radiography and nuclear medicine studies are considered ancillary. This manuscript illustrates representative images of superficial and deep soft tissue infections such as infectious cellulitis, superficial and deep fasciitis, including the necrotizing fasciitis, pyomyositis/soft tissue abscess, septic bursitis and tenosynovitis on different imaging modalities, with emphasis on MRI. Typical histopathologic findings of soft tissue infections are also presented. The imaging approach described in the manuscript is based on relevant literature and authors' personal experience and everyday practice. (orig.)

Not-so-Soft Skills

Science.gov (United States)

Curran, Mary

2010-01-01

Much recent discussion about the skills needed to secure Britain's economic recovery has focused on skills for employability. However, too often, these fundamental skills are understood in narrow functional or vocational terms. So-called "soft skills", what Penelope Tobin, in her 2008 paper "Soft Skills: the hard facts", terms "traits and…

Glass transition in soft-sphere dispersions

International Nuclear Information System (INIS)

RamIrez-Gonzalez, P E; Medina-Noyola, M

2009-01-01

The concept of dynamic equivalence among mono-disperse soft-sphere fluids is employed in the framework of the self-consistent generalized Langevin equation (SCGLE) theory of colloid dynamics to calculate the ideal glass transition phase diagram of model soft-sphere colloidal dispersions in the softness-concentration state space. The slow dynamics predicted by this theory near the glass transition is compared with available experimental data for the decay of the intermediate scattering function of colloidal dispersions of soft-microgel particles. Increasing deviations from this simple scheme occur for increasingly softer potentials, and this is studied here using the Rogers-Young static structure factor of the soft-sphere systems as the input of the SCGLE theory, without assuming a priori the validity of the equivalence principle above.

3D printing of soft robotic systems

Science.gov (United States)

Wallin, T. J.; Pikul, J.; Shepherd, R. F.

2018-06-01

Soft robots are capable of mimicking the complex motion of animals. Soft robotic systems are defined by their compliance, which allows for continuous and often responsive localized deformation. These features make soft robots especially interesting for integration with human tissues, for example, the implementation of biomedical devices, and for robotic performance in harsh or uncertain environments, for example, exploration in confined spaces or locomotion on uneven terrain. Advances in soft materials and additive manufacturing technologies have enabled the design of soft robots with sophisticated capabilities, such as jumping, complex 3D movements, gripping and releasing. In this Review, we examine the essential soft material properties for different elements of soft robots, highlighting the most relevant polymer systems. Advantages and limitations of different additive manufacturing processes, including 3D printing, fused deposition modelling, direct ink writing, selective laser sintering, inkjet printing and stereolithography, are discussed, and the different techniques are investigated for their application in soft robotic fabrication. Finally, we explore integrated robotic systems and give an outlook for the future of the field and remaining challenges.

The jet mass distribution after Soft Drop

Energy Technology Data Exchange (ETDEWEB)

Marzani, Simone [Universita di Genova, Dipartimento di Fisica, Genoa (Italy); INFN, Sezione di Genova (Italy); Schunk, Lais [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany); Soyez, Gregory [IPhT, CEA Saclay, CNRS UMR 3681, Gif-Sur-Yvette (France)

2018-02-15

We present a first-principle computation of the mass distribution of jets which have undergone the grooming procedure known as Soft Drop. This calculation includes the resummation of the large logarithms of the jet mass over its transverse momentum, up to next-to-logarithmic accuracy, matched to exact fixed-order results at next-to-leading order. We also include non-perturbative corrections obtained from Monte-Carlo simulations and discuss analytic expressions for hadronisation and Underlying Event effects. (orig.)

The jet mass distribution after Soft Drop

Science.gov (United States)

Marzani, Simone; Schunk, Lais; Soyez, Gregory

2018-02-01

We present a first-principle computation of the mass distribution of jets which have undergone the grooming procedure known as Soft Drop. This calculation includes the resummation of the large logarithms of the jet mass over its transverse momentum, up to next-to-logarithmic accuracy, matched to exact fixed-order results at next-to-leading order. We also include non-perturbative corrections obtained from Monte-Carlo simulations and discuss analytic expressions for hadronisation and Underlying Event effects.

Electroroentgenography in diagnosis of soft tissue tumors

International Nuclear Information System (INIS)

Vintergal'ter, S.F.; Vishevnik, B.I.

1989-01-01

Clinical, electroroentgenographic and X-ray studies of soft tissues were carried out in 425 patients with malignant (75), benign (246) soft tissue tumors and in cases of such soft tissue pathologies of the extremities and body (104). The paper discusses the technicalities of electroroentgenography which produces on one roentgenogram separate images of all components of soft tissues and bones in a given segment. A comparions of image quality assured by electroroentgeno- and roentgenography did not establish any significant difference in soft tissue tumor semiotics

A synthetic dataset for evaluating soft and hard fusion algorithms

Science.gov (United States)

Graham, Jacob L.; Hall, David L.; Rimland, Jeffrey

2011-06-01

There is an emerging demand for the development of data fusion techniques and algorithms that are capable of combining conventional "hard" sensor inputs such as video, radar, and multispectral sensor data with "soft" data including textual situation reports, open-source web information, and "hard/soft" data such as image or video data that includes human-generated annotations. New techniques that assist in sense-making over a wide range of vastly heterogeneous sources are critical to improving tactical situational awareness in counterinsurgency (COIN) and other asymmetric warfare situations. A major challenge in this area is the lack of realistic datasets available for test and evaluation of such algorithms. While "soft" message sets exist, they tend to be of limited use for data fusion applications due to the lack of critical message pedigree and other metadata. They also lack corresponding hard sensor data that presents reasonable "fusion opportunities" to evaluate the ability to make connections and inferences that span the soft and hard data sets. This paper outlines the design methodologies, content, and some potential use cases of a COIN-based synthetic soft and hard dataset created under a United States Multi-disciplinary University Research Initiative (MURI) program funded by the U.S. Army Research Office (ARO). The dataset includes realistic synthetic reports from a variety of sources, corresponding synthetic hard data, and an extensive supporting database that maintains "ground truth" through logical grouping of related data into "vignettes." The supporting database also maintains the pedigree of messages and other critical metadata.

From adhesion to wetting of a soft particle

Science.gov (United States)

Salez, Thomas; Benzaquen, Michael; Raphael, Elie

2014-03-01

Since the seminal works of Hertz, Johnson, Kendall, and Roberts (JKR), and Derjaguin, Muller, and Toporov (DMT), the contact of adhesive elastic solids has been widely studied. This area of research is of tremendous importance: the range of applications now spreads from biology to engineering, as shown by the recent developments on latex particles, biological cells or micro-patterned substrates, to name a few. Using a thermodynamical approach [Salez et al., Soft Matter 9 10699 (2013)], we calculate the adhesion-induced deformation of a spherical elastic particle placed on a rigid substrate, under zero external load, and including an ingredient of importance in soft matter: the interfacial tension of the cap. First, we limit the study to small deformation. In contrast with previous works, we obtain an expression for the free energy that precisely contains the JKR and Young-Dupré asymptotic regimes, and which establishes a continuous bridge between them. Then, we consider the large deformation case, which is relevant for future comparison with numerical simulations and experiments on very soft materials. Using a fruitful analogy with fracture mechanics, we derive the free energy of the problem and thus obtain the equilibrium state for any given choice of physical parameters.

Soft Robotics: from scientific challenges to technological applications

Science.gov (United States)

Laschi, C.

2016-05-01

Soft robotics is a recent and rapidly growing field of research, which aims at unveiling the principles for building robots that include soft materials and compliance in the interaction with the environment, so as to exploit so-called embodied intelligence and negotiate natural environment more effectively. Using soft materials for building robots poses new technological challenges: the technologies for actuating soft materials, for embedding sensors into soft robot parts, for controlling soft robots are among the main ones. This is stimulating research in many disciplines and many countries, such that a wide community is gathering around initiatives like the IEEE TAS TC on Soft Robotics and the RoboSoft CA - A Coordination Action for Soft Robotics, funded by the European Commission. Though still in its early stages of development, soft robotics is finding its way in a variety of applications, where safe contact is a main issue, in the biomedical field, as well as in exploration tasks and in the manufacturing industry. And though the development of the enabling technologies is still a priority, a fruitful loop is growing between basic research and application-oriented research in soft robotics.

Windchill-201 - Custom Soft-Type Construction

Science.gov (United States)

Jones, Corey; LaPha, Steven

2013-01-01

This presentation will explain Windchill soft-types-what they are, how they work, and how to construct custom ones, configured specifically for your system. The process and particulars of creating and implementing a WTDocument soft-type will be discussed, and the interaction between soft-types and Windchill objects will be shown.

Embodying Soft Wearables Research

DEFF Research Database (Denmark)

Tomico, Oscar; Wilde, Danielle

2016-01-01

of soft wearables. Throughout, we will experiment with how embodied design research techniques might be shared, developed, and used as direct and unmediated vehicles for their own reporting. Rather than engage in oral presentations, participants will lead each other through a proven embodied method...... and knowledge transfer in the context of soft wearables....

A Computational Modeling Approach for Investigating Soft Tissue Balancing in Bicruciate Retaining Knee Arthroplasty

Directory of Open Access Journals (Sweden)

Shahram Amiri

2012-01-01

Full Text Available Bicruciate retaining knee arthroplasty, although has shown improved functions and patient satisfaction compared to other designs of total knee replacement, remains a technically demanding option for treating severe cases of arthritic knees. One of the main challenges in bicruciate retaining arthroplasty is proper balancing of the soft tissue during the surgery. In this study biomechanics of soft tissue balancing was investigated using a validated computational model of the knee joint with high fidelity definitions of the soft tissue structures along with a Taguchi method for design of experiments. The model was used to simulate intraoperative balancing of soft tissue structures following the combinations suggested by an orthogonal array design. The results were used to quantify the corresponding effects on the laxity of the joint under anterior-posterior, internal-external, and varus-valgus loads. These effects were ranked for each ligament bundle to identify the components of laxity which were most sensitive to the corresponding surgical modifications. The resulting map of sensitivity for all the ligament bundles determined the components of laxity most suitable for examination during intraoperative balancing of the soft tissue. Ultimately, a sequence for intraoperative soft tissue balancing was suggested for a bicruciate retaining knee arthroplasty.