Magnetic resonance imaging signal intensity of temporomandibular joint disk and posterior attachment in patients with internal derangement

International Nuclear Information System (INIS)

Jeong, Yeon Hwa; Cho, Bong Hae

2001-01-01

To analyze the possible association between magnetic resonance imaging signal intensity of temporomandibular joint disk and posterior attachment, and the type and extent of disk displacement, disk donfiguration, effusion and clinical signs in patients with internal derangement. Magnetic resonance images of the 132 temporomandibular joints of 66 patients with temporomandibular joint displacement were analyzed. The clinical findings were obtained by retrospective review of the patients' records. The type and extent of disk displacement, disk configuration and effusion were evaluated on the proton density MR images. The signal intensity from the anterior band, posterior band and posterior attachment were measured on MR images. The associations between the type and extent of disk displacement, disk configuration, effusion and clinical signs and the MR signal intensity of disk and posterior attachment were statistically analyzed by student's t-test. Of 132 joints, 87 (65.9%) showed anterior disk displacement with reduction (ADR) and 45 (34.1%) showed anterior disk displacement without reduction (ADnR). This signals from posterior attachments were lower in joints with ADnR than those of ADR (p<0.05). The results showed statistically significant (p<0.05) association between the type and extent of disk displacement and disk configuration, and decreased signal intensity of posterior attachment. There were no statistical associations between pain, noise and limited mouth opening, and signal intensity of disk and posterior attachment. The average signal from posterior attachment was lower in joints with ADnR than that of ADR. The type and extent of disk displacement and disk configuration appeared to be correlated with the signal intensity from posterior attachment

7th International Joint Conference on Computational Intelligence

CERN Document Server

Rosa, Agostinho; Cadenas, José; Correia, António; Madani, Kurosh; Ruano, António; Filipe, Joaquim

2017-01-01

This book includes a selection of revised and extended versions of the best papers from the seventh International Joint Conference on Computational Intelligence (IJCCI 2015), held in Lisbon, Portugal, from 12 to 14 November 2015, which was composed of three co-located conferences: The International Conference on Evolutionary Computation Theory and Applications (ECTA), the International Conference on Fuzzy Computation Theory and Applications (FCTA), and the International Conference on Neural Computation Theory and Applications (NCTA). The book presents recent advances in scientific developments and applications in these three areas, reflecting the IJCCI’s commitment to high quality standards.

El Control y la Confianza: dos rivales en las "International Joint Ventures"

Directory of Open Access Journals (Sweden)

Francisco Puig Blanco

2013-02-01

Full Text Available Las empresas conjuntas internacionales(International Joint Ventures se caracterizan pordos factores íntimamente relacionados: el control y eloportunismo. En este trabajo, trataremos de analizarla relación entre ambos factores y estudiaremos quétipos de control ayudarían a prevenir o a reducirel oportunismo en este tipo de empresas. Además,trataremos de identificar las ventajas e inconvenientesasociados al control y analizaremos el caso de unaInternational Joint Venture formada por dos empresas,una española y la otra americana, cuyo fracaso se debió,en gran parte, a la ausencia de control (confianza y aloportunismo.   ABSTRACT International Joint Ventures are distinguished bytwo closely related factors: control and opportunism.In this paper we will try to analyze the relationshipbetween both factors and we will study what controlswould help prevent or reduce opportunism in thisclass of enterprises. Besides, we will attempt to identifythe advantages and inconveniences associated withcontrol, and analyze one case of an International JointVenture comprised by two companies, a Spanish and anAmerican one whose failure was largely due to lack ofcontrol (trust and opportunism.

RILEM International Symposium on Materials and Joints in Timber Structures

CERN Document Server

Reinhardt, H-W; Garrecht, Harald

2014-01-01

This book contains the contributions from the RILEM International Symposium on Materials and Joints in Timber Structures that was held in Stuttgart, Germany from October 8 to 10, 2013. It covers recent developments in the materials and the joints used in modern timber structures. Regarding basic wooden materials, the contributions highlight the widened spectrum of products comprising cross-laminated timber, glulam and LVL from hardwoods and block glued elements. Timber concrete compounds, cement bonded wood composites and innovative light-weight constructions represent increasingly employed alternatives for floors, bridges and facades. With regard to jointing technologies, considerable advances in both mechanical connections and glued joints are presented. Self-tapping screws have created unprecedented options for reliable, strong as well as ductile joints and reinforcement technologies. Regarding adhesives, which constitute the basis of the jointing/laminating technology of modern timber products, extended o...

Micromechanical and internal discontinuity aspects in fusion welded joints

International Nuclear Information System (INIS)

Nur Azida Che Lah; Aidy Ali

2009-01-01

Full text: This paper deals with characterization of macrostructure, microstructure, hardness, elemental compositions and internal discontinuities of ASTM A516 grade 70 fusion welded joints. The welded joints of ASTM A516 grade 70 carbon steel, which are widely used in pressure vessel fabrication were prepared using welding procedures of Manual Metal Arc (MMA), Metal Inert Gas (MIG) and Tungsten Inert Gas (TIG). Local microstructural condition and elemental composition of the welds were characterised using scanning electron microscopy (SEM) in association with energy dispersive X-ray (EDX). Radiography testing was applied to study the common internal weld defects. This comprehensive information provides a practical guide in order to determine the most adequate welding procedure and assisting in understanding the behaviour of the weld zones. (author)

Design and analysis of push pipe joint under internal pressure and temperature loading

International Nuclear Information System (INIS)

Abid, M.; Alam, K.

2005-01-01

Pipe joints flanged or welded are commonly used in industry for different applications ranging from sewerage to the high pressure and temperature applications. However, with the rapidly changing technological trends, for optimized space such as for heat exchanger applications, pipe joint design needs special consideration, especially for the internal pipe where no flanged/bolted joint due to space constraint can be used. In addition, where joint opening/closing is the requirement for maintenance or other functional purposes, it becomes inevitable to use some special design. In this paper, a push joint proposed is designed, analyzed, optimized and tested for safe stress and operating conditions. An experimental test rig is designed and tests are performed for internal pressure and temperature separately and joint's behaviour is analyzed in detail for any leaks. FEA results are compared and verified with the mathematical results. Based on the experimental observations, the joint is safe as no leaks are observed. (author)

Managing international joint venture relationships - A longitudinal perspective

NARCIS (Netherlands)

Hyder, A.; Ghauri, P.N.

The purpose of the study is to describe and analyse the formation and development of international joint venture processes and relationships between the partners over time. Moreover, the study analyzes how far foreign partners have been successful in developing new contacts and in expanding their

What differences in the cultural backgrounds of partners are detrimental for international joint ventures?

NARCIS (Netherlands)

H.G. Barkema (Harry); G.A.M. Vermeulen (Freek)

1997-01-01

textabstractAn international joint venture implies that a firm has to cooperate with a partner with a different cultural background. In this study, hypotheses about which differences in national culture are most disruptive for international joint ventures were developed and tested using Hofstede's

'Soft' human resource management in small international joint ventures

DEFF Research Database (Denmark)

Dao, Li

2012-01-01

This paper examines the value creation aspects of HRM in international joint ventures of a relatively small size and their implications for strategic management. We assume that HRM in this context is rather a process than a function, and a ‘soft’ – humanistic rather than a ‘hard’, instrumentalist...... of joint venture autonomy. A conceptual framework developed from these empirical insights invites further generalizing efforts, and more importantly, contributes to a dynamic understanding of HRM in small IJVs....

[effectiveness of open reduction and internal fixation without opening joint capsule on tibial plateau fracture].

Science.gov (United States)

Chen, Qi; Xu, Xiaofeng; Huang, Yonghui; Cao, Xingbing; Meng, Chen; Cao, Xueshu; Wei, Changbao

2014-12-01

To introduce the surgery method to reset and fix tibial plateau fracture without opening joint capsule, and evaluate the safety and effectiveness of this method. Between July 2011 and July 2013, 51 patients with tibial plateau fracture accorded with the inclusion criteria were included. All of 51 patients, 17 cases underwent open reduction and internal fixation without opening joint capsule in trial group, and 34 cases underwent traditional surgery method in control group. There was no significant difference in gender, age, cause of injury, time from injury to admission, side of injury, and types of fracture between 2 groups (P > 0.05). The operation time, intraoperative blood loss, incision length, incision healing, and fracture healing were compared between 2 groups. The tibial-femoral angle and collapse of joint surface were measured on X-ray film. At last follow-up, joint function was evaluated with Hospital for Special Surgery (HSS) knee function scale. The intraoperative blood loss in trial group was significantly less than that in control group (P time and the rate of incision healing between 2 groups (P > 0.05). The patients were followed up 12-30 months (mean, 20.4 months) in trial group and 12-31 months (mean, 18.2 months) in control group. X-ray films indicated that all cases in 2 groups obtained fracture healing; there was no significant difference in the fracture healing time between 2 groups (t=1.382, P=0.173). On X-ray films, difference was not significant in tibial-femoral angle and collapse of joint surface between 2 groups (P > 0.05). HSS score of the knee in trial group was significantly higher than that of control group (t=3.161, P=0.003). It can reduce the intraoperative blood loss and shorten the incision length to use open reduction and internal fixation without opening joint capsule for tibial plateau fracture. Traction of joint capsule is helpful in the reduction and good recovery of joint surface collapse. In addition, the surgery without

CLASSIFICATION OF TEMPOROMANDIBULAR-JOINT OSTEOARTHROSIS AND INTERNAL DERANGEMENT .2. SPECIFIC DIAGNOSTIC-CRITERIA

NARCIS (Netherlands)

STEGENGA, B; DEBONT, LGM; BOERING, G

Separate entities of temporomandibular joint osteoarthrosis and internal derangement are operationally defined. Criteria are based on an analysis of the diagnostic significance of symptoms and signs, principles of synovial joint pathology in general, and on therapeutic considerations. The primary

Joint degrees and engaging with a Europe of Knowledge: lessons ...

African Journals Online (AJOL)

This case study of staff perspectives and quality assurance assessment of joint degrees offers insights into the challenges and the lessons that can be learned and the lived reality of this type of international curriculum development from the practitioner perspective. Keywords: international joint degrees, international ...

Third International Joint Conference on Computational Intelligence (IJCCI 2011)

CERN Document Server

Dourado, António; Rosa, Agostinho; Filipe, Joaquim; Computational Intelligence

2013-01-01

The present book includes a set of selected extended papers from the third International Joint Conference on Computational Intelligence (IJCCI 2011), held in Paris, France, from 24 to 26 October 2011. The conference was composed of three co-located conferences:  The International Conference on Fuzzy Computation (ICFC), the International Conference on Evolutionary Computation (ICEC), and the International Conference on Neural Computation (ICNC). Recent progresses in scientific developments and applications in these three areas are reported in this book. IJCCI received 283 submissions, from 59 countries, in all continents. This book includes the revised and extended versions of a strict selection of the best papers presented at the conference.

Evaluation of body posture in individuals with internal temporomandibular joint derangement.

Science.gov (United States)

Munhoz, Wagner Cesar; Marques, Amélia Pasqual; de Siqueira, José Tadeu Tesseroli

2005-10-01

Temporomandibular dysfunctions (TMD) comprise a great number of disruptions that may affect the temporomandibular joint (TMJ), the masticatory muscles, or both. TMJ internal derangement is a specific type of TMD, of which the etiology and physiopathology are broadly unknown, but have been suggested to be linked to head, neck, and body posture factors. This study aimed at verifying possible relationships between body posture and TMJ internal derangements (TMJ-id), by comparing 30 subjects presenting typical TMJ-id signs to 20 healthy subjects. Subjects' clinical evaluations included anamnesis, stomatognatic system evaluation, and plotting analysis on body posture photographs. No statistically significant differences were found between the groups. Results do not support the assertion that body posture plays a role in causing or enhancing TMD; however, these results should be cautiously considered because of the small number of subjects evaluated and the many posture variables submitted to statistical procedures that lead to high standard deviations.

Cultural Distance and the Performance of International Joint Ventures

DEFF Research Database (Denmark)

Christoffersen, Jeppe; Globerman, Steven; Nielsen, Bo Bernhard

2013-01-01

This study provides a critical summary and assessment of the empirical literature on the relationship between cultural distance and the performance of international joint ventures (IJVs) based on studies published over the period 1993-2008. The existing literature reports inconsistent and largely...

The International Criminal Court: Considerations for the Joint Force Commander

National Research Council Canada - National Science Library

Sutton, Michael

2003-01-01

An analysis of the issues and remedies a Joint Force Commander should be concerned about because of the relationship between the United States and the newly-created International Criminal Court (ICC...

The effects of temporomandibular joint internal derangement and degenerative joint disease on tomographic and arthrotomographic images.

Science.gov (United States)

Brand, J W; Whinery, J G; Anderson, Q N; Keenan, K M

1989-02-01

In a blind study, 243 arthrograms were interpreted as showing normal disk position, anterior disk displacement with reduction, or anterior disk displacement without reduction. The presence or absence of a perforation of the posterior attachment or disk was recorded. Later, tomograms of the same patient were interpreted. The presence or absence of evidence of temporomandibular degenerative joint disease (TMDJD) was recorded. The condyle-to-fossa relationship was characterized as retropositioned or not retropositioned. O the 106 cases with tomographic evidence of TMDJD, 100 (94%) had arthrographic evidence of internal derangement (p less than 0.0001), whereas 47% of the cases with internal derangement (211) had evidence of TMDJD. Perforations were seen in 29 (27%) of the cases with degenerative joint disease and in none (0%) of the cases without TMDJD (p less than 0.001). In cases without TMDJD, 90% of the cases with internal derangement revealed condylar retropositioning (p less than 0.0001). With tomographic evidence of TMDJD present, the relationship between condylar position and disk position was not significant.

Joint international conference ICIEOM-CIO-IIE 2015

CERN Document Server

Ferreira, Carlos; Junior, Milton; Prado, Carlos

2017-01-01

This book gathers a selection of the best papers presented at the joint international conference ICIEOM-CIO-IIE 2015, offering recent research on industrial engineering, management and operations from an international and interdisciplinary perspective. It includes contributions from different fields, such as operations research, modeling and simulation, production and service management and logistics, information systems and quality, and as such is of interest to both researchers and practitioners. Reflecting the interconnected nature of today’s production systems, characterized by intense flows of goods, information and individuals between companies and nations, it is a valuable resource for anyone wanting an in-depth understanding of the field to guide managerial practice in order to take full advantage of existing opportunities.

[Development and clinical application of a new type of anatomical locking plate for sternoclavicular joint fracture and dislocation].

Science.gov (United States)

Sun, Yuanlin; Yang, Yunkang; Ge, Jianhua; Yang, Kun; Xiang, Feifan; Zhou, Ju; Liang, Jie

2018-03-01

To report a new type of anatomical locking plate for sternocalvicular joint, and investigate its effectiveness in treatment of sternoclavicular joint fracture and dislocation. A new type of anatomical locking plate for sternoclavicular joint was developed, which accorded with the anatomical features and biomechanical characteristics of Chinese sternoclavicular joint. By adopting the method of clinical randomized controlled study, 32 patients with the sternoclavicular joint fracture and dislocation who met the selection criteria between June 2008 and May 2015 were randomly divided into groups A and B ( n =16), and the patients were treated with new anatomic locking plate and distal radial T locking plate internal fixation, respectively. There was no significant difference between 2 groups in gender, age, injured side, body mass index, cause of injury, type of injury, the time from injury to operation, and preoperative Rockwood grading score ( P >0.05). The operation time, intraoperative blood loss, incision length, hospitalization time, and postoperative complications in 2 groups were recorded, and the effectiveness was evaluated by Rockwood grading score. The operations of 2 groups completed successfully. The operation time, intraoperative blood loss, and hospitalization time in group A were significantly less than those in group B ( P case of sternoclavicular joint pain and 2 cases of wound infection; in group B, there were 1 case of sternoclavicular joint pain, 1 case of internal fixation loosening, and 1 case of sternoclavicular joint re-dislocation; there was no significant difference in complication incidence between 2 groups ( P =1.000). The Rockwood grading scores at each time point after operation in 2 groups were significantly higher than those before operation. At 1 month after operation, the Rockwood grading score in group A was significantly higher than that in group B ( t= 2.270, P =0.031); but there was no significant difference in the Rockwood

Individual learning effects on knowledge transfer in international joint ventures

DEFF Research Database (Denmark)

Dao, Li Thuy; Napier, Nancy

2016-01-01

This paper examines micro (individual-level) aspects of knowledge transfer and learning in international joint ventures in an emerging economy context. Learning by expatriate and local managers appears far more complex, mutually dependent, and significant to the knowledge transfer process than...... suggested in existing literature. Building upon conceptualizations of individual learning and cognitive – behavioural effects in an organisational context while drawing evidence from two cases of Danish – Vietnamese joint ventures, we propose a model of individual-level knowledge transfer and learning...

4th International Joint Conference on Computational Intelligence

CERN Document Server

Correia, António; Rosa, Agostinho; Filipe, Joaquim

2015-01-01

The present book includes extended and revised versions of a set of selected papers from the Fourth International Joint Conference on Computational Intelligence (IJCCI 2012)., held in Barcelona, Spain, from 5 to 7 October, 2012. The conference was sponsored by the Institute for Systems and Technologies of Information, Control and Communication (INSTICC) and was organized in cooperation with the Association for the Advancement of Artificial Intelligence (AAAI). The conference brought together researchers, engineers and practitioners in computational technologies, especially those related to the areas of fuzzy computation, evolutionary computation and neural computation. It is composed of three co-located conferences, each one specialized in one of the aforementioned -knowledge areas. Namely: - International Conference on Evolutionary Computation Theory and Applications (ECTA) - International Conference on Fuzzy Computation Theory and Applications (FCTA) - International Conference on Neural Computation Theory a...

76 FR 45311 - International Joint Commission Public Hearings on Binational Management of Lake of the Woods and...

Science.gov (United States)

2011-07-28

... DEPARTMENT OF STATE [Public Notice 7537] International Joint Commission Public Hearings on Binational Management of Lake of the Woods and Rainy River Watershed The International Joint Commission (IJC) will hold public hearings on the final report of its International Lake of the Woods and Rainy River...

A novel multi-item joint replenishment problem considering multiple type discounts.

Directory of Open Access Journals (Sweden)

Ligang Cui

Full Text Available In business replenishment, discount offers of multi-item may either provide different discount schedules with a single discount type, or provide schedules with multiple discount types. The paper investigates the joint effects of multiple discount schemes on the decisions of multi-item joint replenishment. In this paper, a joint replenishment problem (JRP model, considering three discount (all-unit discount, incremental discount, total volume discount offers simultaneously, is constructed to determine the basic cycle time and joint replenishment frequencies of multi-item. To solve the proposed problem, a heuristic algorithm is proposed to find the optimal solutions and the corresponding total cost of the JRP model. Numerical experiment is performed to test the algorithm and the computational results of JRPs under different discount combinations show different significance in the replenishment cost reduction.

Tensile Test of Welding Joint Parts for a Plate-type Fuel Assembly

Energy Technology Data Exchange (ETDEWEB)

Yoon, K. H.; Kim, J. Y.; Kim, H. J.; Yim, J. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

The tensile tests were performed using an INSTRON 4505 (universal tensile) testing machine. These welding joints are composed of two parts for the soundness of the fuel assembly; one is the side plate with a fixing bar and the other is a side plate with an end fitting. These two joint parts are fabricated by TIG welding method. The tensile tests of the welding joints of a plate-type FA are executed by a tensile test. The fixture configurations for the specimen are very important to obtain the strict test results. The maximum strength has an approximately linear correlation with the unit bonding length of the welding joints. In spite of these results, the maximum strengths of the welding joints are satisfied according to the minimum requirement. These tensile tests of the joint parts for a plate-type fuel assembly (FA) have to be executed to evaluate the structural strength. For the tensile test, the joint parts of a FA used in the test are made of aluminum alloy (Al6061-T6)

Tensile Test of Welding Joint Parts for a Plate-type Fuel Assembly

International Nuclear Information System (INIS)

Yoon, K. H.; Kim, J. Y.; Kim, H. J.; Yim, J. S.

2013-01-01

The tensile tests were performed using an INSTRON 4505 (universal tensile) testing machine. These welding joints are composed of two parts for the soundness of the fuel assembly; one is the side plate with a fixing bar and the other is a side plate with an end fitting. These two joint parts are fabricated by TIG welding method. The tensile tests of the welding joints of a plate-type FA are executed by a tensile test. The fixture configurations for the specimen are very important to obtain the strict test results. The maximum strength has an approximately linear correlation with the unit bonding length of the welding joints. In spite of these results, the maximum strengths of the welding joints are satisfied according to the minimum requirement. These tensile tests of the joint parts for a plate-type fuel assembly (FA) have to be executed to evaluate the structural strength. For the tensile test, the joint parts of a FA used in the test are made of aluminum alloy (Al6061-T6)

Joint Radiation Emergency Management Plan of the International Organizations. Date Effective: 1 July 2013

International Nuclear Information System (INIS)

2013-01-01

European Commission) are party to legally binding treaties and have directives and regulations which have a bearing on the emergency response arrangements in their Member States. There are also bilateral agreements between some international organizations that also have relevance to preparedness and response arrangements. In 2002, the IAEA issued Preparedness and Response for a Nuclear or Radiological Emergency (IAEA Safety Standards Series No. GS-R-2), jointly sponsored by the FAO, the International Labour Organization (ILO), the OECD Nuclear Energy Agency (OECD/NEA), the Pan American Health Organization (PAHO), the United Nations Office for the Co-ordination of Humanitarian Affairs (OCHA) and WHO. The requirements established therein imply additional expectations with regard to operational emergency preparedness and response arrangements. It is recognized by the participating organizations, and reflected in the above requirements, that good planning in advance of an emergency can substantially improve the response. With this in mind, international organizations that participate in the IACRNE develop, maintain and co-sponsor this Joint Radiation Emergency Management Plan of the International Organizations (the 'Joint Plan'). The IAEA is the main coordinating body for the development and maintenance of the Joint Plan. The Joint Plan does not prescribe arrangements between the participating organizations, but describes a common understanding of how each organization acts during a response and in making preparedness arrangements. Nothing in the Joint Plan should be construed as superseding the arrangements in place in the international organizations (or States). However, all international organizations (and States), irrespective of whether they are members of IACRNE, are invited to consider these arrangements in their own emergency management plans. This publication is the sixth edition of the Joint Plan. It includes new arrangements/initiatives which were introduced after

Joint Radiation Emergency Management Plan of the International Organizations. Date Effective: 1 July 2013

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-07-01

European Commission) are party to legally binding treaties and have directives and regulations which have a bearing on the emergency response arrangements in their Member States. There are also bilateral agreements between some international organizations that also have relevance to preparedness and response arrangements. In 2002, the IAEA issued Preparedness and Response for a Nuclear or Radiological Emergency (IAEA Safety Standards Series No. GS-R-2), jointly sponsored by the FAO, the International Labour Organization (ILO), the OECD Nuclear Energy Agency (OECD/NEA), the Pan American Health Organization (PAHO), the United Nations Office for the Co-ordination of Humanitarian Affairs (OCHA) and WHO. The requirements established therein imply additional expectations with regard to operational emergency preparedness and response arrangements. It is recognized by the participating organizations, and reflected in the above requirements, that good planning in advance of an emergency can substantially improve the response. With this in mind, international organizations that participate in the IACRNE develop, maintain and co-sponsor this Joint Radiation Emergency Management Plan of the International Organizations (the 'Joint Plan'). The IAEA is the main coordinating body for the development and maintenance of the Joint Plan. The Joint Plan does not prescribe arrangements between the participating organizations, but describes a common understanding of how each organization acts during a response and in making preparedness arrangements. Nothing in the Joint Plan should be construed as superseding the arrangements in place in the international organizations (or States). However, all international organizations (and States), irrespective of whether they are members of IACRNE, are invited to consider these arrangements in their own emergency management plans. This publication is the sixth edition of the Joint Plan. It includes new arrangements/initiatives which were introduced after

The characteristics and performance of international joint ventures in Thailand

OpenAIRE

Suwannarat, P

2010-01-01

The importance of strategic alliances in the form of international joint ventures (IJVs) is growing in the present international business environment where competition is on a global scale. A review of the IJV literature, especially in developing countries, shows an over-emphasis on China and the NIEs (the first tier newly-industrialising economies: Taiwan, Singapore, Hong Kong, and South Korea). To date, relatively little attention has been paid to the ASEAN4 countries (the high-performing e...

International trade shows: Structure, strategy and performance of exhibitors at individual booths vs. joint booths

DEFF Research Database (Denmark)

Hansen, Kåre

2000-01-01

This paper examines differences in exhibitors who participate at international trade shows at joint booths and those who participate at individual booths. The structure, strategy, and trade show performance of exhibitors at joint booths and those at individual booths are analysed. The analysis...... implications for exhibitors at interna-tional trade shows and export marketing programmes and other marketing programmes offering services to international trade show exhibitors....... of exhibitors at the international food shows SIAL (Paris) and ANUGA (Cologne) showed several significant differences with regard to structure and strategy. However, no significant differences in the performance assessments between the two partici-pation modes were found. The findings have important...

Optimized and practical electrical joints for CORC type HTS cables

CERN Document Server

Mulder, T; van der Laan, D C; Mentink, M G T; Dhallé, M; ten Kate, H H J

2015-01-01

Within CERN the development of REBCO-CORC (Conductor On Round Core) type cables is pursued in view of possible application in future detector and accelerator magnets. An important issue is the design and qualification of terminations for connecting CORC cables mutually or to bus-bars. A termination design is envisaged that combines a simple manufacturing process with a lowest possible joint terminal resistance in the few nΩ range at 4.2 K, first for a single CORC cable and subsequently for CORC based Cable-in-Conduit Conductors. The investigation concerns the effect of tapering the CORC cable within the joint to form a staircase like geometry, which allows current to pass more directly from the copper joint casing to the inner REBCO layers of the CORC cable. Simulations have shown a substantial decrease in joint resistance at operating current in the case both CORC cable and joint casing are tapered. The CORC cable and new joint were tested at CERN. In this paper, some details of the new joint design, fabric...

Optimized and practical electrical joints for CORC type HTS cables

International Nuclear Information System (INIS)

Mulder, T; Dudarev, A; Mentink, M G T; Ten Kate, H H J; Van der Laan, D C; Dhallé, M

2015-01-01

Within CERN the development of REBCO-CORC (Conductor On Round Core) type cables is pursued in view of possible application in future detector and accelerator magnets. An important issue is the design and qualification of terminations for connecting CORC cables mutually or to bus-bars. A termination design is envisaged that combines a simple manufacturing process with a lowest possible joint terminal resistance in the few nΩ range at 4.2 K, first for a single CORC cable and subsequently for CORC based Cable-in-Conduit Conductors. The investigation concerns the effect of tapering the CORC cable within the joint to form a staircase like geometry, which allows current to pass more directly from the copper joint casing to the inner REBCO layers of the CORC cable. Simulations have shown a substantial decrease in joint resistance at operating current in the case both CORC cable and joint casing are tapered. The CORC cable and new joint were tested at CERN. In this paper, some details of the new joint design, fabrication process, and model are presented and the results are summarized. (paper)

An International Urogynecological Association (IUGA)/International Continence Society (ICS) joint report on the terminology for female anorectal dysfunction

OpenAIRE

Sultan, A. H.; Monga, A.; Lee, J.; Emmanuel, A.; Norton, C.; Santoro, G.; Hull, T.; Berghmans, B.; Brody, S.; Haylen, B. T.

2017-01-01

INTRODUCTION AND HYPOTHESIS: The terminology for anorectal dysfunction in women has long been in need of a specific clinically-based Consensus Report. METHODS: This Report combines the input of members of the Standardization and Terminology Committees of two International Organizations, the International Urogynecological Association (IUGA) and the International Continence Society (ICS), assisted on Committee by experts in their fields to form a Joint IUGA/ICS Working Group on Female Anorectal...

An International Urogynecological Association (IUGA)/International Continence Society (ICS) Joint Report on the Terminology for Female Anorectal Dysfunction

OpenAIRE

Sultan, A. H.; Monga, A.; Lee, J.; Emmanuel, A.; Norton, C.; Santoro, G.; Hull, T.; Berghmans, B.; Brody, S.; Haylen, B. T.

2017-01-01

INTRODUCTION: The terminology for anorectal dysfunction in women has long been in need of a specific clinically-based Consensus Report. METHODS: This Report combines the input of members of the Standardization and Terminology Committees of two International Organizations, the International Urogynecological Association (IUGA) and the International Continence Society (ICS), assisted on Committee by experts in their fields to form a Joint IUGA/ICS Working Group on Female Anorectal Termi...

Comparison of MRI findings with clinical symptoms in temporomandibular joint internal derangement

Energy Technology Data Exchange (ETDEWEB)

Kwon, Ki Jeong [Chonbuk National University College of Medicine, Gwangju (Korea, Republic of)

2005-06-15

To determine the clinical correlation of magnetic resonance imaging (MRI) findings of temporomandibular joint internal derangements. The MR images of 150 TMJs in 75 patients were analyzed. The clinical symptoms were pain in the pre auricular area and masticatory muscles and TMJ sounds. There was a statistically significant relationship between the MRI diagnoses of different types of disc displacements and clinical findings of pain, clicking, and crepitus. The risk of TMJ pain was increased when the disc displacement without reduction occurred at the same time in combination with the osteoarthrosis and effusion. Regardless of the results, the data indicate that each of these MR imaging variables may not be regarded as the unique and dominant factor in defining TMJ pain occurrence.

Kinematics and Dynamics Analysis of a 3-DOF Upper-Limb Exoskeleton with an Internally Rotated Elbow Joint

OpenAIRE

Xin Wang; Qiuzhi Song; Xiaoguang Wang; Pengzhan Liu

2018-01-01

The contradiction between self-weight and load capacity of a power-assisted upper-limb exoskeleton for material hanging is unresolved. In this paper, a non-anthropomorphic 3-degree of freedom (DOF) upper-limb exoskeleton with an internally rotated elbow joint is proposed based on an anthropomorphic 5-DOF upper-limb exoskeleton for power-assisted activity. The proposed 3-DOF upper-limb exoskeleton contains a 2-DOF shoulder joint and a 1-DOF internally rotated elbow joint. The structural parame...

Proceedings of the 1991 Joint International Waste Management Conference

International Nuclear Information System (INIS)

1991-01-01

This proceedings contains articles of 1991 joint international waste management conference. It was held on October 21-23, 1991 in Seoul, Korea. The main subject titles are as follows: national waste management programs, waste management in developing countries, incineration - development and experience, site characterization and performance assessment, waste disposal, decontamination and decommissioning, waste solidification and waste form, radioactive waste processing, mixed waste and others (Yi, J. H.)

Second International Joint Conference on Computational Intelligence (IJCCI 2010)

CERN Document Server

Correia, António; Rosa, Agostinho; Filipe, Joaquim; Computational Intelligence

2012-01-01

The present book includes a set of selected extended papers from the second International Joint Conference on Computational Intelligence (IJCCI 2010), held in Valencia, Spain, from 24 to 26 October 2010. The conference was composed by three co-located conferences:  The International Conference on Fuzzy Computation (ICFC), the International Conference on Evolutionary Computation (ICEC), and the International Conference on Neural Computation (ICNC). Recent progresses in scientific developments and applications in these three areas are reported in this book. IJCCI received 236 submissions, from 49 countries, in all continents. After a double blind paper review performed by the Program Committee, only 30 submissions were accepted as full papers and thus selected for oral presentation, leading to a full paper acceptance ratio of 13%. Additional papers were accepted as short papers and posters. A further selection was made after the Conference, based also on the assessment of presentation quality and audience inte...

Acromioclavicular joint separation

Directory of Open Access Journals (Sweden)

Devan Pandya, BS

2018-04-01

Full Text Available History of present illness: A 30-year-old male was brought in by ambulance to the emergency department as a trauma activation after a motorcycle accident. The patient was the helmeted rider of a motorcycle traveling at an unknown speed when he lost control and was thrown off his vehicle. He denied loss of consciousness, nausea, or vomiting. The patient’s vital signs were stable and his only complaint was pain around his left shoulder. On exam, the patient had a prominent left clavicle without skin compromise. He had adequate range of motion in the left shoulder with moderate pain, and his left upper extremity was neurovascularly intact. Significant findings: Plain films of the left shoulder showed elevation of the left clavicle above the acromion. There was an increase in the acromioclavicular (AC and coracoclavicular (CC distances (increased joint distances marked with red and blue arrows, respectively. A normal AC joint measures 1-3 mm whereas a normal CC distance measures 11-13 mm.1 The injury was classified as a Rockwood type III AC joint separation. Discussion: The AC joint is a synovial joint between an oval facet on the acromion and a similar facet on the distal end of the clavicle. Horizontal stability is provided by the AC joint while axial stability is provided by the CC joint.2,3 AC joint injuries account for about 9%-12% of shoulder girdle injuries, and the most common mechanism is direct trauma.4,5 Initial evaluation with imaging includes plain films with three views: the anterior-posterior (AP view with the shoulder in internal and external rotation as well as an axillary, or scapula-Y view (sensitivity 40%, specificity 90% for all films.6,7 AC joint injuries are classified by the Rockwood system.8 Type I involves a sprain or incomplete tear of the AC ligaments with an intact CC ligament. The AC joint appears normal on X-ray, but can become widened with stress, achieved by having the patient hold a 10-15 pound weight from each

Posterior treatment of delayed traumatic atlantoaxial joint dislocation with apofix internal fixation

International Nuclear Information System (INIS)

Qing Wei; Jiang Weimin; Shi Jinhui; Li Xuefeng; Yang Huilin; Tang Tiansi

2010-01-01

Objective: To assess the effect of posterior fixation and fusion with Apofix device for the treatment of delayed traumatic atlantoaxial joint dislocation. Methods: Eighteen patients with delayed traumatic atlantoaxial joint dislocation were included. Posterior fixation and fusion with Apofix device were performed. First step was one or two week skull traction. After the atlantoaxial joint dislocation had been reduced, the posterior fixation and fusion with Apofix was performed. Using local anaesthesia, atlantoaxial interval and posterior structure of atlas and dentata were exposed by midline operative approach. Apofix interlaminar clamps were placed at posterior arch of atlas and odontoid vertebral laminae, autologous iliac bone graft was placed for fusion. Then the device to proper position was pressurized and items locked. Results: All of the patients were followed up, the mean follow-up period was 38 months (13 ∼ 84 months). Fifteen patients obtained complete reduction, the others were partial reduction. Seventeen patients had successful fusion after 3 or 4 months, only 1 patient who had partial reduction had internal fixation loose and nonfusion, leading to recurrence of atlantoaxial joint dislocation. An occipitocervical fusion surgery was performed on this patient. As to neurological assessment, 16 patients had neurological deficit before operation, while 6 of them recovered completely after operation, another 10 patients' neurological status improved significantly. JOA score was improved from 9.5 pre-operative to 15.8 post-operative. Conclusion: Apofix internal fixation and fusion seems to be feasible in treatment of delayed traumatic atlantoaxial joint dislocation. Successful reduction before operation and proper treatment after operation is also important. (authors)

Temporomandibular joint arthrocentesis for internal derangement with disc displacement without reduction.

Science.gov (United States)

Bhargava, Darpan; Jain, Megha; Deshpande, Ashwini; Singh, Ajita; Jaiswal, Jagdish

2015-06-01

Temporomandibular joint (TMJ) disc derangement is defined as a malpositioning of the articular disc relative to the condyle and eminence. Arthrocentesis of the TMJ is a minimally invasive chair side procedure for the patients with TMJ internal derangement. This case report presents convincing results to keep arthrocentesis as an imperative procedure to relieve such patients of their acute symptoms. TMJ dynamics has also been discussed for an in-depth understanding of the pathology in cases with internal derangement.

Optimal Joint Detection and Estimation That Maximizes ROC-Type Curves.

Science.gov (United States)

Wunderlich, Adam; Goossens, Bart; Abbey, Craig K

2016-09-01

Combined detection-estimation tasks are frequently encountered in medical imaging. Optimal methods for joint detection and estimation are of interest because they provide upper bounds on observer performance, and can potentially be utilized for imaging system optimization, evaluation of observer efficiency, and development of image formation algorithms. We present a unified Bayesian framework for decision rules that maximize receiver operating characteristic (ROC)-type summary curves, including ROC, localization ROC (LROC), estimation ROC (EROC), free-response ROC (FROC), alternative free-response ROC (AFROC), and exponentially-transformed FROC (EFROC) curves, succinctly summarizing previous results. The approach relies on an interpretation of ROC-type summary curves as plots of an expected utility versus an expected disutility (or penalty) for signal-present decisions. We propose a general utility structure that is flexible enough to encompass many ROC variants and yet sufficiently constrained to allow derivation of a linear expected utility equation that is similar to that for simple binary detection. We illustrate our theory with an example comparing decision strategies for joint detection-estimation of a known signal with unknown amplitude. In addition, building on insights from our utility framework, we propose new ROC-type summary curves and associated optimal decision rules for joint detection-estimation tasks with an unknown, potentially-multiple, number of signals in each observation.

Kinematics and Dynamics Analysis of a 3-DOF Upper-Limb Exoskeleton with an Internally Rotated Elbow Joint

Directory of Open Access Journals (Sweden)

Xin Wang

2018-03-01

Full Text Available The contradiction between self-weight and load capacity of a power-assisted upper-limb exoskeleton for material hanging is unresolved. In this paper, a non-anthropomorphic 3-degree of freedom (DOF upper-limb exoskeleton with an internally rotated elbow joint is proposed based on an anthropomorphic 5-DOF upper-limb exoskeleton for power-assisted activity. The proposed 3-DOF upper-limb exoskeleton contains a 2-DOF shoulder joint and a 1-DOF internally rotated elbow joint. The structural parameters of the 3-DOF upper-limb exoskeleton were determined, and the differences and singularities of the two exoskeletons were analyzed. The workspace, the joint torques and the power consumption of two exoskeletons were analyzed by kinematics and dynamics, and an exoskeleton prototype experiment was performed. The results showed that, compared with a typical anthropomorphic upper-limb exoskeleton, the non-anthropomorphic 3-DOF upper-limb exoskeleton had the same actual workspace; eliminated singularities within the workspace; improved the elbow joint force situation; and the maximum elbow joint torque, elbow external-flexion/internal-extension and shoulder flexion/extension power consumption were significantly reduced. The proposed non-anthropomorphic 3-DOF upper-limb exoskeleton can be applied to a power-assisted upper-limb exoskeleton in industrial settings.

International joint research of medical and walfare appliances; Iryo fukushi kiki kokusai kyodo kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

To further elevate the medical level and to actively enhance Japan`s contribution to the world in its effort to properly meet the task of advancing longevity of men common to all the advanced countries, investigations were made to study how international joint research should be conducted in the field of medical and welfare appliances. Candidate projects in international joint research and investigations up to fiscal 1993 were arranged, and explanation was made about the strategic and long-term research and development projects (started in fiscal 1995) about medical and welfare appliances undertaken by the Ministry of Trade and Industry of Japan. The two are quite similar to each other, the Ministry of Trade and Industry program comprising six projects that are micropores collection of blood/microdose analysis, high precision three dimensional image assisted diagnosis, less invasive surgery, artificial organs, care assisting intelligent equipment, and welfare equipment for care at home, centering about which international joint research should be propelled. Visits were made to the scenes of research and development of advanced medical and welfare appliances in the U.S. and Canada and their actual state was studied in search for possible joint researches. Further, research and development institutions in Europe were visited and information was exchanged. 25 figs., 15 tabs.

How do country risk and national cultural differences between partners affect the survival of international alliances in emerging countries? Longitudinal analysis of 165 international joint ventures in Brazil 1974 to 2005

Directory of Open Access Journals (Sweden)

Pierre-Xavier Meschi

2007-06-01

Full Text Available This article aims at identifying the individual and joint impact of two « country-level variables », namely national distance and country risk, on the survival of international joint ventures in emerging countries. Research hypotheses predicting the negative impact of national distance and country risk on survival are formulated in this article. These research hypotheses are tested in a sample of 165 international joint ventures that were formed in Brazil between 1974 and 2003. These joint ventures were subjected to an event history analysis over a period of time ranging from 1974 to 2005. The empirical results show that the intercultural dynamics increases the instability of international joint ventures whereas the survival of these alliances does not seem to be affected by the economic and political uncertainty of Brazil. Furthermore, the national distance between local and foreign partners has effects on survival that are variable according to the life cycle of international joint ventures.

The interaction between internal R&D and different types of external knowledge sourcing: an empirical study of Chinese innovative firms

NARCIS (Netherlands)

Chen, Y.; Vanhaverbeke, W.; Du, J.

2016-01-01

This paper investigates to what extent internal R&D efforts and different types of external knowledge sources jointly affect innovation performance of firms in emerging economies. Based on a survey about external knowledge sourcing activities of Chinese innovative firms, we categorize external

TARGETING THE HUMAN DOMAIN: REACHING INTERNAL, JOINT, AND ADVERSARIAL AUDIENCES

Science.gov (United States)

2017-04-06

86th Medical Support Squadron, Ramstein Air Base, Germany . In this capacity, she commanded a 197-person unit providing health care support services to...religion, illustrated via such military- specific rites as the Uniformed Code of Military Justice as a moral compass. This holds for smaller groupings...within a service, as well as for larger joint and international allied warfighting. Correspondingly, service history , rhetoric and literature must focus

Software Technologies - 8th International Joint Conference, ICSOFT 2013 : Revised Selected Papers

NARCIS (Netherlands)

Cordeiro, José; van Sinderen, Marten J.

2014-01-01

The present book includes extended and revised versions of a set of selected papers from the 8th International Joint Conference on Software Technologies (ICSOFT 2013), which was co-organized by the Reykjavik University (RU) and sponsored by the Institute for Systems and Technologies of Information,

International joint research of the Danube radioactivity

International Nuclear Information System (INIS)

Szerbin, P.; Szabo, G.; Guczi, J.; Koblinger-Bokori, E.; Kurtacs, E.; Dovlete, C.; Ruzsa, G.; Major, V.; Maringer, F.J.

1998-01-01

A PHARE (Poland Hungary Aid for Reconstruction of Economy) subsidized study was initiated in 1995 with coordination of Vituki Innosystem (Hungary) and with participation of Austrian, Romanian, and Hungarian research institutes to reveal and investigate in detail hot spots of radioactivity and sources of contamination in the Danube catchment area. The general objective of the project was to assess whether or not potential upstream radionuclide sources in the countries in the upper part of the Danube basin have resulted in evidential downstream accumulation of radionuclides and have a potential impact into the Black sea contamination. The presentation summarizes the results of the international joint research study, and some other data obtained in the framework of cooperation between monitoring institutes of the riparian states

Research Status and Feasibility Analysis on the Participation in International Joint Studies for Radionuclide and Colloid Migration Using Foreign Underground Research Facilities

Energy Technology Data Exchange (ETDEWEB)

Baik, Min Hoon; Park, Chung Kyun; Lee, Jae Kwang; Choi, Jong Won

2007-12-15

The research status of the potential international joint projects that we can join were analyzed by investigating world-wide underground research facilities. Based upon the investigations, we visited Aspo in Sweden and GTS in Switzerland, discussed about the participation in the international joint projects and mutual cooperation, and then discussed in detail about time and method for the participation by inviting an expert from Nagra. It is resulted from the investigations and discussions that it is most relevant to participate in the following two international joint projects. 1) Task Force on Modelling of Groundwater Flow and Transport of Solutes in Aspo, 2) CFM project in GTS. We also summarized the on-going current status for the participation in the two international joint projects.

Achievement report for fiscal 1999. FS surveys to excavate international joint research seeds; 1999 nendo kokusai kyodo kenky seeds hakkutsu no tame no FS chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The FS surveys to excavate international joint research seeds are intended to promote international joint researches, whereas surveys have been carried out in fiscal 1999 on eight themes covering as wide scope as new energies, resource conservation, energy conservation, environment preservation, functional materials, information communication technologies, and bio-technologies. The eight themes are: researches on energy conservation in petroleum and petrochemical industries by using advanced distillation processes (to develop an internal heat exchange type distillation column, and realize energy conservation exceeding the minimum reflux status being the limitation of conventional energy saving means), researches on treatment of hard-to-decompose chemical substances by utilizing surface reformation by means of discharge, a new process monitoring technology (process tomography), establishment of human immortalization cells due to co-manifestation of mortalin and telomerase and elucidation of their structure, a remote maintenance technology using integrated type sensors, application of new heat resistant plastics to photo and electronic materials, preparation processes of petroleum catalysts utilizing in situ XAFS, elucidation and design of the structure of the ultra-micro metal activation point in the reaction process, and surveys on necessity of developing a continuous and massive separation system of high-level energy and resource saving type using liquid-liquid distribution. (NEDO)

IAEA/UNESCO Joint International Isotopes in Hydrology Programme

International Nuclear Information System (INIS)

Oezgueler, H.

2002-01-01

International Hydrology Programme (IHP) of UNESCO was established in 1965 as International Hydrological Decade. This programme was transformed to the IHP having the phases of 6-year duration. Presently, IHP-VI Phase (2002-2007) is based on the fundamental principle that freshwater is as essential to sustainable development as it is to life and that water, beyond its geophysical, chemical, biological function in the hydrological cycle, has social, economic and environmental values that are inter-linked and mutually supportive. The international Programme for Isotopes in the Hydrological Cycle 'proposal was presented by IAEA to the Fifth UNESCO-WMO International Conference on Hydrology' held in Geneva in 1999. The Conference noted the proposal and invited UNESCO and IAEA to develop the proposal further in collaboration with WMO, in order to submit it to the relevant bodies of the organizations concerned. At the end of this study, the IAEA / UNESCO Joint International Isotopes in Hydrology Programme (JIIHP) was formed in 2001. The JIIHP will service a number of international needs including the dissemination of research and application results in isotope methodologies through a global infrastructure network. This is foreseen primarily through an appropriate expansion of the IHP National Committees to include experts in isotope methods in hydrology in order to facilitate a more efficient dialogue and mainstreaming of isotope methods in member states of UNESCO. Main areas for co-operation have already been incorporated within the IHP-VI plans. In this paper, with some brief information on the studies to be realised in the near future under the framework of this programme JIIHP, the isotop related priorities of the Turkish hydrology community are explained herewith

Knowledge Creation in International Joint Ventures in Emerging Economies

DEFF Research Database (Denmark)

Nielsen, Ulrik B.

Entering and developing presence in emerging economies often require foreign firms to set up International Joint Ventures (IJVs) with local partners, especially when the prime motive of the operation is to capture opportunities in the local markets (Mohr & Puck, 2005). IJVs have therefore become...... an important way for firms to enter these markets and a significant force in shaping a firm’s global strategy in expanding international activities abroad. However, research has shown that IJVs in emerging economies are unstable, and firms have experienced that performance of their IJVs in these emerging...... economies often does not meet their expectations (Fang & Zou, 2010). Extant research has shown that, in general, management of IJVs appears to be a difficult issue. 60-70% of all partnerships are not successful (Lambe, Spekman, & Hunt, 2002). Inter-partner learning has been proposed in the literature...

Research of the Resistance of Contact Welding Joint of R65 Type Rail

Directory of Open Access Journals (Sweden)

Kęstutis Dauskurdis

2015-03-01

Full Text Available In the article the R65 type rail joints that were welded by resistance welding are analysed. Survey methodology of the research consists of the following parts: visual inspection of welded joint, ultrasonic rail inspection, hardness test of upper part of the rail, fusion area research, the measurement hardness test of heat-softened area, the measurement microhardness test, microstructure research of the welded joint, impact strength experiments, chemical analysis of welded joint, wheel-rail interaction research using the finite element method (FEM. The results of the research are analysed and the quality of weld is evaluated. The conclusion is based on the results of this research.

Working abroad, working with others: How firms learn to operate international joint ventures

NARCIS (Netherlands)

H.G. Barkema (Harry); O. Shenkar (Oded); G.A.M. Vermeulen (Freek); J.H.J. Bell (John)

1997-01-01

textabstractSuccessful international joint ventures entail both learning to operate across national boundaries and learning to cooperate. Hypotheses grounded in organizational learning theory were tested with event-history analysis and data on 1,493 expansions of 25 large Dutch firms between 1966

Prevalence of the types of the petrotympanic fissure in the temporomandibular joint dysfunction

International Nuclear Information System (INIS)

Cakur, Binali; Sumbullu, Muhammed Akif; Durna, Dogan; Akgul, Hayati Murat

2011-01-01

Background Petrotympanic fissure (PTF) is a fissure in the temporal bone that runs from the temporomandibular joint (TMJ) to the tympanic cavity (TC). In PTF, the discomallear ligament (DML) connects the malleus in the tympanic cavity and the articular disc and capsule of the temporomandibular joint. PTF with the DML is a possible cause of aural symptoms related to temporomandibular joint dysfunction (TMD). Purpose To investigate the prevalence of different types of PTF in TMD using dental volumetric tomography (DVT) and determine whether PTF type correlates with age. Material and Methods DVT scans in the sagittal planes of PTFs of 134 patients with TMD were examined for the types of PTF present. Three main PTF types were described: wide, tunnel-shaped structure (type 1); tunnel-shaped structure that is wide open in the PTF entrance to the mandibular fossa and gradually thins out in the tympanic cavity (type 2), tunnel-shaped structure that is wide open in the entrance of the mandibular fossa, with a middle region with a flat-shaped tunnel structure and a narrow exit in the tympanic cavity (type 3). Results In DVT scans, PTF types 1, 2 and 3 were seen in 67.2%, 1.5%, and 31.3% of cases, respectively. We found no significant relationship between age or gender and PTF type. Conclusion The low percentage of type 2 PTF and high percentage of type 1 PTF must be taken into consideration during pre-surgical planning related to TMD. However, future well-designed clinical studies involving larger numbers of subjects will be necessary to confirm the findings of this study

Prevalence of the types of the petrotympanic fissure in the temporomandibular joint dysfunction

Energy Technology Data Exchange (ETDEWEB)

Cakur, Binali; Sumbullu, Muhammed Akif; Durna, Dogan; Akgul, Hayati Murat (Dept. of Oral Diagnosis and Oral Radiology, Faculty of Dentistry, Ataturk Univ., Erzurum (Turkey)), email: bcakur@atauni.edu.tr

2011-06-15

Background Petrotympanic fissure (PTF) is a fissure in the temporal bone that runs from the temporomandibular joint (TMJ) to the tympanic cavity (TC). In PTF, the discomallear ligament (DML) connects the malleus in the tympanic cavity and the articular disc and capsule of the temporomandibular joint. PTF with the DML is a possible cause of aural symptoms related to temporomandibular joint dysfunction (TMD). Purpose To investigate the prevalence of different types of PTF in TMD using dental volumetric tomography (DVT) and determine whether PTF type correlates with age. Material and Methods DVT scans in the sagittal planes of PTFs of 134 patients with TMD were examined for the types of PTF present. Three main PTF types were described: wide, tunnel-shaped structure (type 1); tunnel-shaped structure that is wide open in the PTF entrance to the mandibular fossa and gradually thins out in the tympanic cavity (type 2), tunnel-shaped structure that is wide open in the entrance of the mandibular fossa, with a middle region with a flat-shaped tunnel structure and a narrow exit in the tympanic cavity (type 3). Results In DVT scans, PTF types 1, 2 and 3 were seen in 67.2%, 1.5%, and 31.3% of cases, respectively. We found no significant relationship between age or gender and PTF type. Conclusion The low percentage of type 2 PTF and high percentage of type 1 PTF must be taken into consideration during pre-surgical planning related to TMD. However, future well-designed clinical studies involving larger numbers of subjects will be necessary to confirm the findings of this study

Pneumatic-type dynamic traction and flexion splint for treating patients with extension contracture of the metacarpophalangeal joint.

Science.gov (United States)

Nakayama, Jun; Horiki, Mituru; Denno, Kakurou; Ogawa, Kazunori; Oka, Hisao; Domen, Kazuhisa

2016-02-01

Collateral ligament shortening causes extension contractures of the metacarpophalangeal joint, and dynamic flexion splinting has been widely used to treat these contractures; however, there are various problems with these approaches. We developed a novel, pneumatic-type dynamic traction and flexion splint to solve these problems. A total of 25 fingers were treated with the dynamic traction and flexion splint for 8 weeks. Every 2 weeks, the average metacarpophalangeal joint flexion angle, total active motion, grasp strength, and pain scores were assessed. The finger flexion angle was significantly greater at the final evaluation, starting after 6 weeks of treatment (p < 0.05), than prior to treatment. Similarly, the total active motion results improved significantly over 8 weeks. Our results show that use of the dynamic traction and flexion splint improves patient finger functioning and flexural angle. The dynamic traction and flexion (DTF) splint appears to be effective for treating patients. © The International Society for Prosthetics and Orthotics 2015.

IMPACTS OF DIFFERENT JOINT ANGLES AND ADHESIVES ON DIAGONAL TENSION PERFORMANCES OF BOX-TYPE FURNITURE

Directory of Open Access Journals (Sweden)

Musa Atar

2010-02-01

Full Text Available The goal of this study was to determine the effects of different joint angles and adhesives on diagonal tension performances of the box-type furniture made from solid wood and medium density fiberboard (MDF. After drilling joints of 75º, 78º, 81º, 84º, and 87º degrees on Oriental beech, European oak, Scotch pine, and MDF samples, a diagonal tensile test was applied on corners glued with polyvinyl acetate (PVAc and polyurethane (D-VTKA = Desmodur-Vinyl Trieketonol Acetate according to ASTM D 1037 standard. With reference to the obtained results, the highest tensile strength was obtained in European oak with PVAc glue and joint angle of 84º, while the lowest value was obtained in MDF with D-VTKA glue and joint angle of 75º. Considering the interaction of wood, adhesive, and joint angle, the highest tensile strength was obtained in European oak with joint angle of 81º and D-VTKA glue (1.089 N.mm-2, whereas the lowest tensile strength was determined in MDF with joint angle of 75º and PVAc glue (0.163 N.mm-2. Therefore, PVAc as glue and 81º as joint angle could be suggested to obtain some advantageous on the dovetail joint process for box-type furniture made from both solid wood and MDF.

The 3rd International Joint Conference ICIEOM-ADINGOR-IISE-AIM-ASEM (IJC2017) PROCEEDINGS - “New Global Perspectives on Industrial Engineering and Management”

OpenAIRE

Poler Escoto, Raúl; Mula Bru, Josefa; Díaz-Madroñero Boluda, Francisco Manuel; Sanchis Gisbert, Raquel

2017-01-01

The IJC2017 Proceedings contains the contributions presented in the 3rd International Joint Conference ICIEOM – ADINGOR – IISE – AIM - ASEM : “XXIII International Conference on Industrial Engineering and Operations Management”, “International ADINGOR Conference 2017”, “International IISE Conference 2017”, “International AIM Conference 2017” and “International ASEM Conference 2017”. This International Joint Conference is a result of an agreement among ADINGOR (Asociación para el Desarrollo ...

Distal tibial pilon fractures (AO/OTA type B, and C) treated with the external skeletal and minimal internal fixation method.

Science.gov (United States)

Milenković, Sasa; Mitković, Milorad; Micić, Ivan; Mladenović, Desimir; Najman, Stevo; Trajanović, Miroslav; Manić, Miodrag; Mitković, Milan

2013-09-01

Distal tibial pilon fractures include extra-articular fractures of the tibial metaphysis and the more severe intra-articular tibial pilon fractures. There is no universal method for treating distal tibial pilon fractures. These fractures are treated by means of open reduction, internal fixation (ORIF) and external skeletal fixation. The high rate of soft-tissue complications associated with primary ORIF of pilon fractures led to the use of external skeletal fixation, with limited internal fixation as an alternative technique for definitive management. The aim of this study was to estimate efficacy of distal tibial pilon fratures treatment using the external skeletal and minimal internal fixation method. We presented a series of 31 operated patients with tibial pilon fractures. The patients were operated on using the method of external skeletal fixation with a minimal internal fixation. According to the AO/OTA classification, 17 patients had type B fracture and 14 patients type C fractures. The rigid external skeletal fixation was transformed into a dynamic external skeletal fixation 6 weeks post-surgery. This retrospective study involved 31 patients with tibial pilon fractures, average age 41.81 (from 21 to 60) years. The average follow-up was 21.86 (from 12 to 48) months. The percentage of union was 90.32%, nonunion 3.22% and malunion 6.45%. The mean to fracture union was 14 (range 12-20) weeks. There were 4 (12.19%) infections around the pins of the external skeletal fixator and one (3.22%) deep infections. The ankle joint arthrosis as a late complication appeared in 4 (12.90%) patients. All arthroses appeared in patients who had type C fractures. The final functional results based on the AOFAS score were excellent in 51.61%, good in 32.25%, average in 12.90% and bad in 3.22% of the patients. External skeletal fixation and minimal internal fixation of distal tibial pilon fractures is a good method for treating all types of inta-articular pilon fractures. In

IRS Guidelines: Joint IAEA/NEA International Reporting System for Operating Experience

International Nuclear Information System (INIS)

2010-01-01

The International Reporting System for Operating Experience (IRS) is an international system jointly operated by the International Atomic Energy Agency (IAEA) and the OECD Nuclear Energy Agency (OECD/NEA). The fundamental objective of the IRS is to contribute to improving the safety of commercial nuclear power plants which are operated worldwide. This objective can be achieved by providing timely and detailed information on lessons learned from operating and construction experience at the international level. This information could be related to issues and events that are related to safety. The purpose of these guidelines is to describe the system and to give users the necessary background and guidance to enable them to produce IRS reports meeting a high standard of quality while retaining the effectiveness of the system expected by all Member States operating nuclear power plants. As this system is owned by the Member States, the IRS Guidelines have been developed and approved by the IRS National Co-ordinators with the assistance of both Secretariats (IAEA/NEA).

Effects of joint alignment and type on mechanical properties of thermoplastic articulated ankle-foot orthosis.

Science.gov (United States)

Gao, Fan; Carlton, William; Kapp, Susan

2011-06-01

Articulated or hinged ankle-foot orthosis (AFO) allow more range of motion. However, quantitative investigation on articulated AFO is still sparse. The objective of the study was to quantitatively investigate effects of alignment and joint types on mechanical properties of the thermoplastic articulated AFO. Tamarack dorsiflexion assist flexure joints with three durometers (75, 85 and 95) and free motion joint were tested. The AFO joint was aligned with the center of the motor shaft (surrogate ankle joint), 10 mm superior, inferior, anterior and posterior with respect to the motor shaft center. The AFO was passively moved from 20° plantar flexion to 15° dorsiflexion at a speed of 10°/s using a motorized device. Mechanical properties including index of hysteresis, passive resistance torque and quasi-static stiffness (at neutral, 5°, 10° and 15° in plantar flexion) were quantified. Significant effects of joint types and joint alignment on the mechanical properties of an articulated thermoplastic AFO were revealed. Specifically, center alignment showed minimum resistance and stiffness while anterior and posterior alignment showed significantly higher resistance and stiffness. The dorsiflexion assist torques at neutral position ranged from 0.69 ± 0.09 to 1.88 ± 0.10 Nm. Anterior and posterior alignment should be avoided as much as possible. The current study suggested that anterior and posterior alignment be avoided as much as possible in clinical practice due to potential skin irritation and increase in stress around the ankle joint.

Adaptive plasticity in mammalian masticatory joints

Science.gov (United States)

Ravosa, Matthew J.; Kunwar, Ravinder; Nicholson, Elisabeth K.; Klopp, Emily B.; Pinchoff, Jessie; Stock, Stuart R.; Stack, M. Sharon; Hamrick, Mark W.

2006-08-01

Genetically similar white rabbits raised on diets of different mechanical properties, as well as wild-type and myostatin-deficient mice raised on similar diets, were compared to assess the postweaning effects of elevated masticatory loads due to increased jaw-adductor muscle and bite forces on the proportions and properties of the mandibular symphysis and temporomandibular joint (TMJ). Microcomputed tomography (microCT) was used to quantify bone structure at a series of equidistant external and internal sites in coronal sections for a series of joint locations. Discriminant function analyses and non-parametric ANOVAs were used to characterize variation in biomineralization within and between loading cohorts. In both species, long-term excessive loading results in larger joint proportions, thicker articular and cortical bone, and increased biomineralization of hard tissues. Such adaptive plasticity appears designed to maintain the postnatal integrity of masticatory joint systems for a primary loading environment(s). This behavioral signal may be increasingly mitigated in older organisms by the interplay between adaptive and degradative joint tissue responses.

'Soft' human resource management in small international joint ventures:Cases from the Danish-Vietnamese context

OpenAIRE

Dao, Li

2012-01-01

This paper examines the value creation aspects of HRM in international joint ventures of a relatively small size and their implications for strategic management. We assume that HRM in this context is rather a process than a function, and a ‘soft’ – humanistic rather than a ‘hard’, instrumentalist managerial approach. Using cases from a modest sample of Danish – Vietnamese joint ventures, we propose that HRM is significantly associated with creating a healthy and adaptive environment for mutua...

Success factors for international HTA projects: evaluating EUnetHTA Joint Action as an exemplar.

Science.gov (United States)

Guegan, Eleanor Woodford; Cook, Andrew

2014-11-01

Evaluation is essential for the management of international projects or networks in health technology assessment (HTA). It extends beyond the normal process of project management by incorporating qualitative dimensions and provides information about a project's effectiveness and achievements. This article aimed to identify the factors that are important for the success of international HTA projects. The European network for Health Technology Assessment Joint Action (EUnetHTA JA) is presented as an exemplar. METHODS for the evaluation of international HTA projects include interviews, focus groups, questionnaires, observations and documentary review, and the key points of these approaches have been summarized. The impact and effectiveness of the EUnetHTA JA was evaluated by questionnaires of project participants and external stakeholders, and by documentary review. The response rate for the three annual questionnaires sent to project participants ranged from 86 percent to 88 percent and for external stakeholders ranged from 65 percent to 88 percent. Key factors for project success included production of deliverables according to the workplan, achievement of objectives, added value generated, effective communication, involvement of external stakeholders, workstream management and progress from the preceding EUnetHTA 2006-2008 project. The experience of this project can inform the evaluation of future international HTA collaborations, such as the EUnetHTA 2nd Joint Action and HTAsiaLink. A high response rate was achieved to the self-completion questionnaires and the strategy followed is recommended for evaluation of international HTA projects. Future assessments of international HTA projects should strive to measure outcomes and impact, not just outputs and process.

Student perspectives on the development and evaluation of a joint international education to promote employability in Europe.

Science.gov (United States)

Craig, Claire; Piškur, Barbara

2012-01-01

This article presents a student evaluation of a joint international education developed as part of a European project which sought to equip health care practitioners with the skills to support employability of individuals furthest removed from the labour market, disadvantaged on account of age, gender, migration or ethnicity. Thirty eight students out of the forty one students that participated in the pilot of four modules (NL, UK, SE, DE) returned completed digital questionnaires (92.6% response rate). The study is descriptive by nature. A questionnaire was used to collect the data from students. Additionally students attending the module in the UK also took part in a series of qualitative interviews which sought to explore their experiences in more detail. These were recorded, transcribed and analyzed. Students reported that joint education facilitates competence development. The competencies they identified (Information Communications Technology) were recognised as being key to enhancing employability of disadvantaged groups. The joint international education exemplified by EEE4all offers one model of how to build a responsive international curriculum to ensure that the workforce of the future is well placed to meet the needs of this changing world.

Association of bone marrow edema with temporomandibular joint (TMJ) osteoarthritis and internal derangements.

Science.gov (United States)

Wahaj, Aiyesha; Hafeez, Kashif; Zafar, Muhammad Sohail

2017-01-01

This study reviewed the dental literature in order to determine the association of bone marrow edema with osteoarthritis and temporomandibular joint (TMJ) internal derangement disorders. A literature search was performed using electronic databases PubMed/Medline (National Library of Medicine, Bethesda, Maryland) and Cochrane for articles published during the last 15 years (January 2000-December 2014). A predetermined inclusion and exclusion criteria were used for filtering the scientific papers. Research articles fulfilling the basic inclusion criteria were included in the review. The reviewed studies showed that bone marrow edema is found in painful joints with osteoarthritis in a majority of cases. A few cases with no pain or significant degenerative changes are reported to have a bone marrow edema pattern as well. Bone marrow edema, increased fluid level, and pain are associated with osteoarthritis in the majority of patients reporting TMJ arthritis. Degenerative and disc displacement conditions are multifactorial and require further investigations. Magnetic resonance imaging can be employed to detect bone marrow edema even in the absence of pain and clinical symptoms in the patients of internal derangements.

The efficiency of botulinum toxin type A for the treatment of masseter muscle pain in patients with temporomandibular joint dysfunction and tension-type headache.

Science.gov (United States)

Pihut, Malgorzata; Ferendiuk, Ewa; Szewczyk, Michal; Kasprzyk, Katarzyna; Wieckiewicz, Mieszko

2016-01-01

Temporomandibular joint dysfunction are often accompanied by symptoms of headache such as tension-type headache which is the most frequent spontaneous primary headache. Masseter muscle pain is commonly reported in this group. The purpose of the study was to assess the efficiency of intramuscular botulinum toxin type A injections for treating masseter muscle pain in patients with temporomandibular joint dysfunction and tension-type headache. This prospective outcome study consisted of 42 subjects of both genders aged 19-48 years diagnosed with masseter muscle pain related to temporomandibular joint dysfunction and tension-type headache. The subjects were treated by the intramuscular injection of 21 U (mice units) of botulinum toxin type A (Botox, Allergan) in the area of the greatest cross-section surface of both masseter bellies. Pain intensity was evaluated using visual analogue scale (VAS) and verbal numerical rating scale (VNRS) 1 week before the treatment and 24 weeks after the treatment. The obtained data were analyzed using the Wilcoxon matched pairs test (p ≤ 0,005). The results of this study showed a decrease in the number of referred pain episodes including a decrease in pain in the temporal region bilaterally, a reduction of analgesic drugs intake as well as a decrease in reported values of VAS and VNRS after injections (p = 0,000). The intramuscular botulinum toxin type A injections have been an efficient method of treatment for masseter muscle pain in patients with temporomandibular joint dysfunction and tension-type headache.

Whole-body patterns of the range of joint motion in young adults: masculine type and feminine type.

Science.gov (United States)

Moromizato, Keiichi; Kimura, Ryosuke; Fukase, Hitoshi; Yamaguchi, Kyoko; Ishida, Hajime

2016-10-01

Understanding the whole-body patterns of joint flexibility and their related biological and physical factors contributes not only to clinical assessments but also to the fields of human factors and ergonomics. In this study, ranges of motion (ROMs) at limb and trunk joints of young adults were analysed to understand covariation patterns of different joint motions and to identify factors associated with the variation in ROM. Seventy-eight healthy volunteers (42 males and 36 females) living on Okinawa Island, Japan, were recruited. Passive ROM was measured at multiple joints through the whole body (31 measurements) including the left and right side limbs and trunk. Comparisons between males and females, dominant and non-dominant sides, and antagonistic motions indicated that body structures influence ROMs. In principal component analysis (PCA) on the ROM data, the first principal component (PC1) represented the sex difference and a similar covariation pattern appeared in the analysis within each sex. Multiple regression analysis showed that this component was associated with sex, age, body fat %, iliospinale height, and leg extension strength. The present study identified that there is a spectrum of "masculine" and "feminine" types in the whole-body patterns of joint flexibility. This study also suggested that body proportion and composition, muscle mass and strength, and possibly skeletal structures partly explain such patterns. These results would be important to understand individual variation in susceptibility to joint injuries and diseases and in one's suitable and effective postures and motions.

Internal Universes in Models of Homotopy Type Theory

DEFF Research Database (Denmark)

Licata, Daniel R.; Orton, Ian; Pitts, Andrew M.

2018-01-01

We show that universes of fibrations in various models of homotopy type theory have an essentially global character: they cannot be described in the internal language of the presheaf topos from which the model is constructed. We get around this problem by extending the internal language with a mo...... that the interval in cubical sets does indeed have. This leads to a completely internal development of models of homotopy type theory within what we call crisp type theory.......We show that universes of fibrations in various models of homotopy type theory have an essentially global character: they cannot be described in the internal language of the presheaf topos from which the model is constructed. We get around this problem by extending the internal language...

Desmoid type fibromatosis in the facet joint of lumbar spine: Case report and review of literature

Energy Technology Data Exchange (ETDEWEB)

Kim, So Jung; Ha, Doo Hoe; Lee, Sang Min; Kang, Hae Youn [CHA Bundang Medical Center, CHA University, Seongnam (Korea, Republic of)

2013-10-15

Desmoid type fibromatosis is a benign fibroblastic tumor arising from the fascia or musculoaponeurosis. It may occur in various locations, but most commonly in the shoulder girdle and neck; to our knowledge, there has been no reported case originating from a facet joint of the spine. We report CT and MR imaging findings of a desmoid type fibromatosis, involving the facet joint of the L3-4 spine with bone involvement.

Personnel decision-making in wholly-owned foreign subsidiaries and in international joint ventures.

OpenAIRE

Zeira Y; Shenkar O

1986-01-01

ILO pub. Working paper, research report on personnel management decision making in foreign owned subsidiarys of multinational enterprises and international joint ventures - discusses legal aspects, the role of absentee top management, host country employers organizations and other interest groups, etc.; examines employees attitudes, management attitudes, trade union attitudes government attitude, particularly regarding workers participation, recruitment and promotion. References, statistical ...

An Unexplored Facet of International Business in Greece: Foreign and Diaspora Shareholders in Joint Stock Company Start-Ups, 1833-1920

Directory of Open Access Journals (Sweden)

Ioanna Sapfo Pepelasis

2016-07-01

Full Text Available This paper focuses on an unexplored aspect of the history of international business in Greece, the presence of international shareholders in Greek Joint stock company start-ups. Our main findings are that these investors participated in numerous such firms usually as minority shareholders in capital and or knowledge intensive firms. Rarely did they opt for the exclusive international ownership of a joint stock company in Greece and the dividing line  between foreign direct investment and foreign portfolio investment was not always clear. It is also the case that international capital inflow into the nascent corporate sector involved a mosaic of collaborating actors including not only the foreign but also the diasporic.

Distal tibial pilon fractures (AO/OTA type B, and C treated with the external skeletal and minimal internal fixation method

Directory of Open Access Journals (Sweden)

Milenković Saša

2013-01-01

Full Text Available Background/Aim. Distal tibial pilon fractures include extra-articular fractures of the tibial metaphysis and the more severe intra-articular tibial pilon fractures. There is no universal method for treating distal tibial pilon fractures. These fractures are treated by means of open reduction, internal fixation (ORIF and external skeletal fixation. The high rate of soft-tissue complications associated with primary ORIF of pilon fractures led to the use of external skeletal fixation, with limited internal fixation as an alternative technique for definitive management. The aim of this study was to estimate efficacy of distal tibial pilon fratures treatment using the external skeletal and minimal internal fixation method. Methods. We presented a series of 31 operated patients with tibial pilon fractures. The patients were operated on using the method of external skeletal fixation with a minimal internal fixation. According to the AO/OTA classification, 17 patients had type B fracture and 14 patients type C fractures. The rigid external skeletal fixation was transformed into a dynamic external skeletal fixation 6 weeks post-surgery. Results. This retrospective study involved 31 patients with tibial pilon fractures, average age 41.81 (from 21 to 60 years. The average follow-up was 21.86 (from 12 to 48 months. The percentage of union was 90.32%, nonunion 3.22% and malunion 6.45%. The mean to fracture union was 14 (range 12-20 weeks. There were 4 (12.19% infections around the pins of the external skeletal fixator and one (3.22% deep infections. The ankle joint arthrosis as a late complication appeared in 4 (12.90% patients. All arthroses appeared in patients who had type C fractures. The final functional results based on the AOFAS score were excellent in 51.61%, good in 32.25%, average in 12.90% and bad in 3.22% of the patients. Conclusion. External skeletal fixation and minimal internal fixation of distal tibial pilon fractures is a good method for

Effect of welding processes on the impression creep resistance of type 316 LN stainless steel weld joints

International Nuclear Information System (INIS)

Vasudevan, M.; Vasantharaja, P.; Sisira, P.; Divya, K.; Ganesh Sundara Raman, S.

2016-01-01

Type 316 LN stainless steel is the major structural material used in the construction of fast breeder reactors. Activated Tungsten Inert Gas (A-TIG) welding , a variant of the TIG welding process has been found to enhance the depth of penetration significantly during autogenous welding and also found to enhance the creep rupture life in stainless steels. The present study aims at comparing the effect of TIG and A-TIG welding processes on the impression creep resistance of type 316 LN stainless steel base metal, fusion zone and heat affected zone (HAZ) of weld joints. Optical and TEM have been used to correlate the microstructures with the observed creep rates of various zones of the weld joints. Finer microstructure and higher ferrite content was observed in the TIG weld joint fusion zone. Coarser grain structure was observed in the HAZ of the weld joints. Impression creep rate of A-TIG weld joint fusion zone was almost equal to that of the base metal and lower than that of the TIG weld joint fusion zone. A-TIG weld joint HAZ was found to have lower creep rate compared to that of conventional TIG weld joint HAZ due to higher grain size. HAZ of the both the weld joints exhibited lower creep rate than the base metal. (author)

Metallic joints for very high vacuum; Joints metalliques pour ultra-vide

Energy Technology Data Exchange (ETDEWEB)

Paigne, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1961-07-01

After defining three main types of joint; three types of distribution of the tightening force in the clamps are demonstrated; the distribution of stresses, distortion and displacements in these clamps is then calculated by means of the theory of elasticity. This is followed by experimental results on a particular means of tightening (i.e. screw-clamps). From a brief discussion on the behaviour of the clamps it is possible finally to define other types of joint deriving from the main types originally foreseen. (author) [French] Apres avoir defini trois principaux types de joints, on met en evidence trois types de distribution des forces de serrage des brides; puis on calcule a l'aide de la theorie de l'elasticite la distribution des contraintes, deformations et deplacements dans ces brides. On donne ensuite des resultats experimentaux sur un mode de serrage particulier (cas des serres-joints). Une discussion sommaire sur le comportement des brides permet de definir finalement d'autres types de joints derivant des types principaux envisages initialement. (auteur)

Joint Radiation Emergency Management Plan of the International Organizations. Date Effective: 1 January 2010

International Nuclear Information System (INIS)

2010-01-01

The purpose of this Plan is to describe the inter-agency framework for preparedness for and response to a radiation5 incident or emergency irrespective of its cause. In particular, its objectives are: 1. To provide a common understanding of the emergency preparedness and response roles and responsibilities, objectives, authorities, capabilities and arrangements of each participating international organization, and any relevant inter-agency arrangements; 2. To provide an overall concept of operations between the international organizations based on the emergency response objectives, responsibilities, authorities, capabilities and arrangements of each participating international organization, and any existing inter-agency arrangements, in order to facilitate a timely, effective and co-ordinated response; 3. To facilitate development of agreements among the participating international organizations on practical issues, if appropriate; 4. To provide a common understanding of the process for improving and changing the inter-agency response arrangements; 5. To provide a common understanding of roles and responsibilities of the participating international organizations with respect to: international standards, supporting national capabilities through provision of guidance and training, relevant research, emergency exercises and other preparedness considerations; 6. To guide the managers in each participating organization who need to ensure that all appropriate arrangements are given the necessary support within their organization; 7. To facilitate the well founded development, maintenance and training of plans and procedures for each organization; 8. To draw the attention of personnel in States and international organizations6 to these arrangements and to facilitate the development of compatible arrangements, if appropriate. The Joint Plan describes the arrangements of the participating international organizations7 for responding to a radiation incident or emergency

[Classification and Treatment of Sacroiliac Joint Dislocation].

Science.gov (United States)

Tan, Zhen; Huang, Zhong; Li, Liang; Meng, Wei-Kun; Liu, Lei; Zhang, Hui; Wang, Guang-Lin; Huang, Fu-Guo

2017-09-01

To develop a renewed classification and treatment regimen for sacroiliac joint dislocation. According to the direction of dislocation of sacroiliac joint,combined iliac,sacral fractures,and fracture morphology,sacroiliac joint dislocation was classified into 4 types. Type Ⅰ (sacroiliac anterior dislocation): main fracture fragments of posterior iliac wing dislocated in front of sacroiliac joint. Type Ⅱ (sacroiliac posterior dislocation): main fracture fragments of posterior iliac wing dislocated in posterior of sacroiliac joint. Type Ⅲ (Crescent fracturedislocation of the sacroiliac joint): upward dislocation of posterior iliac wing with oblique fracture through posterior iliac wing. Type ⅢA: a large crescent fragment and dislocation comprises no more than onethird of sacroiliac joint,which is typically inferior. Type ⅢB: intermediatesize crescent fragment and dislocation comprises between one and twothirds of joint. Type ⅢC: a small crescent fragment where dislocation comprises most,but not the entire joint. Different treatment regimens were selected for different types of fractures. Treatment for type Ⅰ sacroiliac joint dislocation: anterior iliac fossa approach pry stripping reset; sacroiliac joint fixed with sacroiliac screw through percutaneous. Treatment for type Ⅱ sacroiliac joint dislocation: posterior sacroiliac joint posterior approach; sacroiliac joint fixed with sacroiliac screw under computer guidance. Treatment for type ⅢA and ⅢB sacroiliac joint dislocation: posterior sacroiliac joint approach; sacroiliac joint fixed with reconstruction plate. Treatment for type ⅢC sacroiliac joint dislocation: sacroiliac joint closed reduction; sacroiliac joint fixed with sacroiliac screw through percutaneous. Treatment for type Ⅳ sacroiliac joint dislocation: posterior approach; sacroiliac joint fixed with spinal pelvic fixation. Results of 24 to 72 months patient follow-up (mean 34.5 months): 100% survival,100% wound healing,and 100

Conceptual approaches to international cooperation between higher education institutions

Directory of Open Access Journals (Sweden)

Tetiana Obolenska

2016-12-01

Full Text Available The existing conceptual and technological approaches to the organization and implementation of international cooperation between higher education institutions with the performance of international accreditation based on education quality system have been characterized in complex, considering the key trends of internationalization of higher education. Priority strategies of higher education internationalization and types of international academic cooperation between universities regarding education services were defined. It has been substantiated that the most important manifestation of higher education internationalization is international cooperation between universities regarding rendering education services, while the highest level of internationalization of this service is joint educational programs. A complex analysis of international accreditation requirements to joint education programs was made on the basis of the system of education quality improvement, its advantages were proven and its distinct features that influence the choice and substantiation of international cooperation, marketing and branding of individual programs were characterized. Technology of international accreditation for joint programs was detailed. Special attention was paid to the practical component of launching joint degree programs between Ukrainian and foreign higher education institutions. The experience of joint master’s degree programs of Kyiv National Economic University named after Vadym Hetman and the University of Redlands Business School (California, USA was analyzed.

[Repair and reconstruction for severe fracture and dislocation of ankle joint].

Science.gov (United States)

Yin, Qingwei; Jiang, Yi; Xiao, Lianping; Li, Xiaodong; Fu, Jiaxin; Tian, Yonggang; Han, Liqiang; Liu, Zhi

2008-06-01

To summarize the technique and effect of the therapy for severe fracture and dislocation of ankle joint by operation. From March 2003 to February 2006, 76 cases were treated with primary open restoration and internal fixation for dislocated ankle joint fracture, with 47 males and 29 females, with the average age of 36.4 years (ranging from 18 years to 65 years). According to AO criterion, these fresh fractures were classified into 13 cases for type C3-1, 45 cases for type C3-2 and 18 cases for type C3-3. Based on the Gustilo-Anderson standard, 23 open fractures were classified into 17 cases for type II and 6 cases for type III A. The operation was delayed from 1 hours to 24 hours after the injury. All incisions healed at the first stage except 4 cases which delayed union because of simple infection by revision with ointment. A total of 72 cases were followed up, with the average time of 18.5 months (from 12 months to 35 months). The time of bone union was from 12 weeks to 24 weeks. The screws of fixation for lower tibia-fibula joint were found to be ruptured in 2 cases when further consultation was performed in the 16th and 20th week after the operation, respectively, and were broken within 1 year after the operation. These screws were taken out 12 weeks postoperative in 28 cases, while the whole internal fixations of the rest cases were taken out 1 year after the operation. The postoperative function of malleolus extended from 21.7 degrees to 26.8 degrees and flection from 38.5 degrees to 44.7 degrees. Assessed by the American Orthopaedic Foot and Ankle Society Clinical Rating Scales, 23 cases were excellent, 36 good, 13 fair, and the choiceness rate reached 81.94%. These procedures, together with reduction by twist after hospital, open and internal fixation in time, and parenchyma managed with internal fixation, are important to attain satisfactory effect for the treatment of severe fracture and dislocation of ankle joint.

Features that exacerbate fatigue severity in joint hypermobility syndrome/Ehlers-Danlos syndrome - hypermobility type.

Science.gov (United States)

Krahe, Anne Maree; Adams, Roger David; Nicholson, Leslie Lorenda

2018-08-01

To assess the prevalence, severity and impact of fatigue on individuals with joint hypermobility syndrome (JHS)/Ehlers-Danlos syndrome - hypermobility type (EDS-HT) and establish potential determinants of fatigue severity in this population. Questionnaires on symptoms and signs related to fatigue, quality of life, mental health, physical activity participation and sleep quality were completed by people with JHS/EDS-HT recruited through two social media sites. Multiple regression analysis was performed to identify predictors of fatigue in this population. Significant fatigue was reported by 79.5% of the 117 participants. Multiple regression analysis identified five predictors of fatigue severity, four being potentially modifiable, accounting for 52.3% of the variance in reported fatigue scores. Predictors of fatigue severity were: the self-perceived extent of joint hypermobility, orthostatic dizziness related to heat and exercise, levels of participation in personal relationships and community, current levels of physical activity and dissatisfaction with the diagnostic process and management options provided for their condition. Fatigue is a significant symptom associated with JHS/EDS-HT. Assessment of individuals with this condition should include measures of fatigue severity to enable targeted management of potentially modifiable factors associated with fatigue severity. Implications for rehabilitation Fatigue is a significant symptom reported by individuals affected by joint hypermobility syndrome/Ehlers-Danlos syndrome - hypermobility type. Potentially modifiable features that contribute to fatigue severity in this population have been identified. Targeted management of these features may decrease the severity and impact of fatigue in joint hypermobility syndrome/Ehlers-Danlos syndrome - hypermobility type.

Internal derangements of the temporomandibular joint: findings in the pediatric age group

International Nuclear Information System (INIS)

Katzberg, R.W.; Tallents, R.H.; Hayakawa, K.; Miller, T.L.; Goske, M.J.; Wood, B.P.

1985-01-01

Findings in 31 pediatric patients with pain and dysfunction of the temporomandibular joint (TMJ) are reported. The average age was 14 years and the average duration of symptoms was 21.4 months. Internal derangements were found in 29 patients (94%) and degenerative arthritis in 13 (42%). In 12 patients (39%), the problem could be traced to an injury to the jaw. Secondary condylar hypoplasia was associated with the meniscal abnormality in 3 patients (10%). Further awareness of internal derangements of the TMJ in the pediatric population should permit greater recognition of their etiology. It is important that threatment be initiated as soon as possible, not only to minimize the development of osseous disease in young adults but also to prevent facial growth deformities

Special features of embrittlement of welded joints in shells of VVER-type reactors

International Nuclear Information System (INIS)

Kasatkin, O.G.

1999-01-01

At present, the atomic power engineering of Russia and Ukraine is based on water-water energy reactors of the VVER-440 and VVER-1000 type, with the electric power of 440 and 1000 MW, respectively. The majority of the VVER-440 reactors are installed in Russia, and VVER-1000 reactors operate in Ukraine. The reactors' shell (RS) is produced from cylindrical shells and a dished end welded together by circular joints under a flux. The RS of the VVER-440 reactor is produced from 15Kh3MFA steel, and the VVER-1000 reactors are produced from 15Kh2NMFA steel. The shell of the VVER-1000 reactor has an internal austenite coating. The condition of the RS metal is determined mainly by the critical brittleness temperature T b at which the impact toughness of specimens with a sharp notch reaches 60 J/cm 2 . The energy reactors, working in western countries, are characterised by a service life of 40 years and discussion is being carried out to extend this lifetime to 60 years. The design service life of the domestic reactors varies from 30 (RS VVER-440) to 40 (RS VVER-1000) years. According to investigations, the service life of the shells of these reactors is restricted by the properties of welded joints which are characterised by higher susceptibility to embrittlement than that of the parent metal, especially due to a higher content in the weld of phosphorus (RS VVER-440) or nickel (RS VVER-1000). Therefore, some experts believe that the actual service life of the RS is shorter than the design life. The accurate evaluation of the service life of welded joints in the RS is very important for the safety of service and also in the economic aspects, because the unjustified decrease of the permissible service life and premature shutdown of units of the nuclear power station result in huge losses

Evaluation of Outcomes of Open Reduction and Internal Fixation Surgery in Patients with Type C Distal Humeral Fractures

Directory of Open Access Journals (Sweden)

Mohammadhadi Nouraei

2018-01-01

Full Text Available Background: In this study, functional state of patients with Type C distal humerus fractures undergone surgical plating was evaluated 6 and 12 months after the surgery in order to record postsurgical factors such as pain level and job/performance satisfaction. Materials and Methods: In this cross-sectional study, 46 patients with humerus fractures were recruited and their ability to do daily tasks, presence of degenerative changes, stability of elbow joint, and range of motion was evaluated. For assessment of response to surgery, Mayo score was used. Results: Among 46 patients, 45 (97.8% of them had joint stability. Evaluation of postsurgical complications showed that six subjects (13% had no complications, but superficial infection was observed in 12 (26.1% subjects. Neuromuscular disorders in ulnar nerve were present in 11 subjects (23.9%, recurrent articular bursitis of elbow joint in 6 subjects (13%, stiffness of elbow joint in 29 subjects (63%, nonunion of fracture in 3 subjects (6.5%, and myositis ossification in 4 (8.7% subjects. Furthermore, 18 (39.1% patients presented with more than one (2–4 complications. Conclusion: Open reduction and internal fixation surgery with dual plating is the method of choice for treatment of Type C distal humeral fractures. Evaluation of long-term outcomes of this surgery could be done via several different questionnaires as many studies suggest. This study demonstrated that the outcomes of this surgery in Isfahan, Iran, have been noticeably inferior compared to results of the studies in other parts of the world.

The role of molecular pain biomarkers in temporomandibular joint internal derangement.

Science.gov (United States)

Ernberg, M

2017-06-01

There is evidence that low-grade inflammation may be responsible for pain and development of degenerative changes in temporomandibular joint internal derangement. This article reviews the current knowledge of the molecular mechanisms behind TMJ internal derangements. A non-systematic search was carried out in PubMed, Embase and the Cochrane library for studies regarding pathophysiological mechanisms behind internal derangements focusing on pain-mediating inflammatory and cartilage-degrading molecules. Recent data suggest that release of cytokines may be the key event for pain and cartilage destruction in TMJ internal derangements. Cytokines promote the release of matrix metalloproteinases (MMPs), and due to hypoxia, vascular endothelial growth factor (VEGF) is released. This activates chondrocytes to produce MMPs and reduce their tissue inhibitors (TIMPs) as well as the recruitment of osteoclasts, ultimately leading to cartilage and bone resorption. Also, proteoglycans have an important role in this process. Several cytokines, MMPs, TIMPs and VEGF have been identified in higher concentrations in the TMJ synovial fluid of patients with painful internal derangements and shown to be associated with the degree of degeneration. Other molecules that show elevated levels include hyaluronic acid synthase, disintegrin and metalloproteinase with thrombospondin motifs (ADAMTs), aggrecan, fibromodulin, biglycan and lumican. Taken together, more or less pronounced inflammation of TMJ structures with release of cytokines, MMPs and other molecular markers that interact in a complex manner may be responsible for tissue degeneration in internal derangements. As internal derangements may be symptom-free, the degree of inflammation, but also other mechanisms, may be important for pain development. © 2017 John Wiley & Sons Ltd.

The Joint International Conference of the XII International Conference on Mechanisms and Mechanical Transmissions (MTM) and the XXIII International Conference on Robotics (Robotics ’16)

CERN Document Server

Lovasz, Erwin-Christian; Hüsing, Mathias; Maniu, Inocentiu; Gruescu, Corina

2017-01-01

This volume presents the proceedings of the Joint International Conference of the XII International Conference on Mechanisms and Mechanical Transmissions (MTM) and the XXIII International Conference on Robotics (Robotics ’16), that was held in Aachen, Germany, October 26th-27th, 2016. It contains applications of mechanisms and transmissions in several modern technical fields such as mechatronics, biomechanics, machines, micromachines, robotics and apparatus. In connection with these fields, the work combines the theoretical results with experimental testing. The book presents reviewed papers developed by researchers specialized in mechanisms analysis and synthesis, dynamics of mechanisms and machines, mechanical transmissions, biomechanics, precision mechanics, mechatronics, micromechanisms and microactuators, computational and experimental methods, CAD in mechanism and machine design, mechanical design of robot architecture, parallel robots, mobile robots, micro and nano robots, sensors and actuators in ro...

Temporomandibular joint and muscle disorder-type pain and comorbid pains in a national US sample.

Science.gov (United States)

Plesh, Octavia; Adams, Sally H; Gansky, Stuart A

2011-01-01

To compare prevalences of self-reported comorbid headache, neck, back, and joint pains in respondents with temporomandibular joint and muscle disorder (TMJMD)-type pain in the 2000-2005 US National Health Interview Survey (NHIS), and to analyze these self-reported pains by gender and age for Non-Hispanic (NH) Whites (Caucasians), Hispanics, and NH Blacks (African Americans). Data from the 2000-2005 NHIS included information on gender, age, race, ethnicity, education, different common types of pain (specifically TMJMD-type, severe headache/migraine, neck, and low back pains), changes in health status, and health care utilization. Estimates and test statistics (ie, Pearson correlations, regressions, and logistic models) were conducted using SAS survey analysis and SUDAAN software that take into account the complex sample design. A total of 189,977 people (52% female and 48% males, 73% NH Whites, 12% Hispanic, 11% NH Blacks, and 4% "Other") were included. A total of 4.6% reported TMJMD-type pain, and only 0.77% overall reported it without any comorbid headache/migraine, neck, or low back pains; also 59% of the TMJMD-type pain (n = 8,964) reported ⋝ two comorbid pains. Females reported more comorbid pain than males (odds ratio [OR] = 1.41, P neck pain, 64% low back pain, and 62% joint pain. Differences in gender and race by age patterns were detected. For females, headache/migraine pain with TMJMD-type pain peaked around age 40 and decreased thereafter regardless of race/ethnicity. Neck pain continued to increase up to about age 60, with a higher prevalence for Hispanic women at younger ages, and more pronounced in males, being the highest in the non-Whites. Low back pain was higher in Black and Hispanic females across the age span, and higher among non-White males after age 60. Joint pain demonstrated similar patterns by race/ethnicity, with higher rates for Black females, and increased with age regardless of gender. TMJMD-type pain was most often associated with

Temporomandibular joint

International Nuclear Information System (INIS)

Westesson, P.L.; Hatala, M.; Tallents, R.H.; Katzberg, R.W.; Musgrave, M.; Levitt, S.

1990-01-01

This paper determines the frequency of MR signs of abnormal temporomandibular joints (TMJs) in asymptomatic volunteers. Forty-two volunteers with 84 clinically normal TMJs were imaged in the sagittal and coronal planes with surface coil MR imaging. Sagittal closed and open and coronal closed views were obtained bilaterally in all volunteers. The images were classified as normal (superior disk position) or abnormal (disk displacement of degenerative joint disease). Eighteen joints in 11 volunteers were abnormal; 12 had disk displacement with reduction and six had disk displacement without reduction, with associated degenerative joint disease in three of the six. Asymptomatic internal derangement and degenerative joint disease occur in about one-fourth of asymptomatic volunteers

Joint International Workshop on Professional Learning, Competence Development and Knowledge Management - LOKMOL and L3NCD

NARCIS (Netherlands)

Memmel, Martin; Ras, Eric; Weibelzahl, Stephan; Burgos, Daniel; Olmedilla, Daniel; Wolpers, Martin

2006-01-01

Memmel, M., Ras, E., Weibelzahl, S., Burgos, D., Olmedilla, D., & Wolpers, M. (2006). Joint International Workshop on Professional Learning, Competence Development and Knowledge Management - LOKMOL and L3NCD. Proceedings of ECTEL 2006. October 2nd-4th, Crete, Greece. Retrieved October 2nd, 2006,

Statistical inferences with jointly type-II censored samples from two Pareto distributions

Science.gov (United States)

Abu-Zinadah, Hanaa H.

2017-08-01

In the several fields of industries the product comes from more than one production line, which is required to work the comparative life tests. This problem requires sampling of the different production lines, then the joint censoring scheme is appeared. In this article we consider the life time Pareto distribution with jointly type-II censoring scheme. The maximum likelihood estimators (MLE) and the corresponding approximate confidence intervals as well as the bootstrap confidence intervals of the model parameters are obtained. Also Bayesian point and credible intervals of the model parameters are presented. The life time data set is analyzed for illustrative purposes. Monte Carlo results from simulation studies are presented to assess the performance of our proposed method.

PATHOLOGY OF TEMPOROMANDIBULAR-JOINT INTERNAL DERANGEMENT AND OSTEOARTHROSIS

NARCIS (Netherlands)

DEBONT, LGM; STEGENGA, B

Temporomandibular joint (TMJ) osteoarthrosis and disk displacement seem to be strongly related, but they may also represent mutually independent temporomandibular disorders. This paper presents relevant aspects of normal physiology and degeneration of synovial joints, aspects of normal

Theoretical and experimental studies on bellows type expansion joints behaviour of Chinon 3 primary coolant system

International Nuclear Information System (INIS)

Vrillon, B.; Jeanpierre, F.; Copin, A.; Gregoire, J.P.

1975-01-01

The vibration study of the bellows was performed in two stages. A series of vibration tests was performed on a real bellow joint. By comparing the experimental results with calculations using the finite elements method for revolution shells it was possible to qualify the representation of the waves and reinforcement rings. The resonant frequencies and modes were calculated for the various joints under reactor conditions. According to the excitation sources considered, the amplitude of the displacements and stresses can be determined from these characteristic modes. The corrugations are protected internally from the aerodynamic effects of the gas flow by an inner sleeve welded to the primary piping upstream and free downstream. The annular space between this sleeve and the corrugations forms a resonant volume liable to be excited by flow-induced pressure fluctuations. It was possible to calculate the characteristic resonance frequencies and modes of this gas column (air at normal temperature and pressure). A full-scale mock-up test under conditions corresponding to the calculation hypotheses gave experimental proof of the calculation results. Owing to the good correlation between the results of these two studies an attempt was made to calculate the acoustical behaviour of these cavities for nominal running conditions (temperature and pressure) as a function of the known excitation sources. The results obtained from all these tests show that the use of bellows type expansion joints on a primary reactor circuit offers the same guarantees of reliability and resistance as any other circuit component under pressure, as long as the strains they undergo remain within the limits specified by the regulations and nuclear codifications

[Surgery of ipsilateral Hawkins Ⅲ talus neck and ankle joint fractures via internal and lateral approaches with Herbert screws].

Science.gov (United States)

Zhang, P; Dong, Q R; Wang, Z Y; Chen, B; Wan, J H; Wang, L

2016-11-08

Objective: To explore the manual operation skills of operative treatment of ipsilateral Hawkins Ⅲ talus neck and ankle joint fractures via internal and lateral approaches with Herbert screws, and to study the clinical results. Method: From Jan 2009 to Dec 2014, the clinical data of 13 patients with ipsilateral Hawkins Ⅲ talus neck and ankle joint fractres via internal and lateral approaches with Herbert screws were retrospectively analyzed in our department.There were 10 males and 3 female, ranging in age from 20 to 60 years with an average age of 31.5 years.The fractures occurred on the right side in 9 patients and on the left side in 4 patients.Three cases had the complication of medial malleolar fracture.Ten cases had the complication of medial and lateral malleolar fracture. Totally 11 cases were made calcaneal skeletal traction, and all the were made CT with three-dimensional image reconstruction.Two cases were treated with emergency operation.Eleven cases were treated with selective operation.The operation time was 5 hours-10 days after injury. The functional results were evaluated by American Orthopaedic Foot and Ankle Society (AOFAS). Result: The average duration of follow-up was 22.6 months (range, 14-65 months). There was skin necrosis in one cases, no incision infection, malunion and nonunion of the fractures and loss of reduction. At final follow-up, AOFAS ankle score was 75.2 (range, 42 to 93), higher than preoperative 39.2 (range, 23 to 60), the difference was statistically significant ( P =0.023). The result was excellent in 4 cases, good in 5 cases, fair in 3 cases and 1 cases in poor, and the overall excellent or good rate was 69.2%. Avascular necrosis occurred in 3 cases (23.1%, 3/13). Traumatic arthritis was found in 5 cases (38.5%, 5/13), involved tibial astragaloid joint in 2 cases, involved subtalar joint in 1 case, involved tibial astragaloid joint and subtalar joint in 2 cases. Conclusion: The effect of surgical treatment for ipsilateral

International Joint Conference on Mechanics, Design Engineering & Advanced Manufacturing

CERN Document Server

Nigrelli, Vincenzo; Oliveri, Salvatore; Peris-Fajarnes, Guillermo; Rizzuti, Sergio

2017-01-01

This book gathers papers presented at the International Joint Conference on Mechanics, Design Engineering and Advanced Manufacturing (JCM 2016), held on 14-16 September, 2016, in Catania, Italy. It reports on cutting-edge topics in product design and manufacturing, such as industrial methods for integrated product and process design; innovative design; and computer-aided design. Further topics covered include virtual simulation and reverse engineering; additive manufacturing; product manufacturing; engineering methods in medicine and education; representation techniques; and nautical, aeronautics and aerospace design and modeling. The book is divided into eight main sections, reflecting the focus and primary themes of the conference. The contributions presented here will not only provide researchers, engineers and experts in a range of industrial engineering subfields with extensive information to support their daily work; they are also intended to stimulate new research directions, advanced applications of t...

Joint radiation emergency management plan of the international organizations. Emergency preparedness and response. Date effective: 1 January 2007

International Nuclear Information System (INIS)

2007-01-01

binding treaties and have directives and regulations that bear on emergency response arrangements among some States. There are also bilateral agreements between some international organizations that also have relevance to preparedness and response arrangements. In March 2002, the IAEA issued Safety Requirements, entitled 'Preparedness and Response for a Nuclear or Radiological Emergency' (GS-R-2), jointly sponsored by the FAO, IAEA, the International Labour Organization (ILO), the OECD Nuclear Energy Agency (OECD/NEA), the United Nations Office for the Coordination of Humanitarian Affairs (OCHA), the Pan American Health Organization (PAHO) and WHO. These safety standards imply additional expectations with regard to operational emergency response arrangements. It is recognized by the participating organizations, and reflected in the above requirements, that good planning in advance of an emergency can substantially improve the response. With this in mind, the IAEA, the organizations party to the Conventions, and some other international organizations that participate in the activities of the IACRNA develop and maintain this 'Joint Radiation Emergency Management Plan of the International Organizations' (the Joint Plan), which describes: the objectives of response; the organizations involved in response, their roles and responsibilities, and the interfaces among them and between them and States; operational concepts; and preparedness arrangements. The various organizations reflect these arrangements in their own emergency plans. The IAEA is the main co-ordinating body for development and maintenance of the Joint Plan. All States irrespective whether they are party to one or other of the two Conventions are invited to adopt arrangements that are compatible with those described here when providing relevant information about nuclear or radiological emergencies to relevant international organizations, in order to minimize the radiological consequences and to facilitate the

FLANGE-ORNL, Flanged Pipe Joint Stress Analysis, Internal Pressure, Moment Loads, Temperature

International Nuclear Information System (INIS)

Rodabaugh, E.C.; Moore, S.E.

1979-01-01

1 - Description of problem or function: FLANGE-ORNL calculates appropriate loads, stresses, and displacements for the flanges, bolts, and gaskets that comprise a flanged piping joint for internal pressure or moment loading on the pipe, temperature difference between the flange hub and ring, and variations in bolt load that result from pressure, hub-ring temperature gradient and/or bolt-ring temperature differences. Flanges considered may be tapered-hub, straight or blind. 2 - Method of solution: The solution is based on discontinuity analysis and the theory of plates and shells

Effects of hand grip exercise on shoulder joint internal rotation and external rotation peak torque.

Science.gov (United States)

Lee, Dong-Rour; Jong-Soon Kim, Laurentius

2016-08-10

The goal of this study is to analyze the effects of hand grip training on shoulder joint internal rotation (IR)/external rotation (ER) peak torque for healthy people. The research was conducted on 23 healthy adults in their 20 s-30 s who volunteered to participate in the experiment. Hand grip power test was performed on both hands of the research subjects before/after the test to study changes in hand grip power. Isokinetic machine was used to measure the concentric IRPT (internal rotation peak torque) and concentric ERPT (external rotation peak torque) at the velocity of 60°/sec, 90°/sec, and 180°/sec before/after the test. Hand grip training was performed daily on the subject's right hand only for four weeks according to exercise program. Finally, hand grip power of both hands and the maximum torque values of shoulder joint IR/ER were measured before/after the test and analyzed. There was a statistically significant difference in the hand grip power of the right hand, which was subject to hand grip training, after the experiment. Also, statistically significant difference for shoulder ERPT was found at 60°/sec. Hand grip training has a positive effect on shoulder joint IRPT/ERPT and therefore can help strengthen muscles around the shoulder without using weight on the shoulder. Consequently, hand grip training would help maintain strengthen the muscles around the shoulder in the early phase of rehabilitation process after shoulder surgery.

Effects of hook plate on shoulder function after treatment of acromioclavicular joint dislocation.

Science.gov (United States)

Chen, Chang-Hong; Dong, Qi-Rong; Zhou, Rong-Kui; Zhen, Hua-Qing; Jiao, Ya-Jun

2014-01-01

Internal fixation with hook plate has been used to treat acromioclavicular joint dislocation. This study aims to evaluate the effect of its use on shoulder function, to further analyze the contributing factors, and provide a basis for selection and design of improved internal fixation treatment of the acromioclavicular joint dislocation in the future. A retrospective analysis was performed on patients treated with a hook plate for acromioclavicular joint dislocation in our hospital from January 2010 to February 2013. There were 33 cases in total, including 25 males and 8 females, with mean age of 48.27 ± 8.7 years. There were 29 cases of Rockwood type III acromioclavicular dislocation, 4 cases of type V. The Constant-Murley shoulder function scoring system was used to evaluate the shoulder function recovery status after surgery. Anteroposterior shoulder X-ray was used to assess the position of the hook plate, status of acromioclavicular joint reduction and the occurrence of postoperative complications. According to the Constant-Murley shoulder function scoring system, the average scores were 78 ± 6 points 8 to 12 months after the surgery and before the removal of the hook plate, the average scores were 89 ± 5 minutes two months after the removal of hook plate. Postoperative X-ray imaging showed osteolysis in 10 cases (30.3%), osteoarthritis in six cases (18.1%), osteolysis associated with osteoarthritis in four cases(12.1%), and steel hook broken in one case (3%). The use of hook plate on open reduction and internal fixation of the acromioclavicular joint dislocation had little adverse effect on shoulder function and is an effective method for the treatment of acromioclavicular joint dislocation. Osteoarthritis and osteolysis are the two common complications after hook plate use, which are associated with the impairment of shoulder function. Shoulder function will be improved after removal of the hook plate.

Predicting the Functional Roles of Knee Joint Muscles from Internal Joint Moments

DEFF Research Database (Denmark)

Flaxman, Teresa E; Alkjær, Tine; Simonsen, Erik B

2017-01-01

INTRODUCTION: Knee muscles are commonly labeled as flexors or extensors and aptly stabilize the knee against sagittal plane loads. However, how these muscles stabilize the knee against adduction-abduction and rotational loads remains unclear. Our study sought 1) to classify muscle roles as they r...... on its role in maintaining knee joint stability in the frontal and transverse loading planes. This is useful for delineating the roles of biarticular knee joint muscles and could have implications in robotics, musculoskeletal modeling, sports sciences, and rehabilitation....

Neutron irradiation test of copper alloy/stainless steel joint materials

International Nuclear Information System (INIS)

Yamada, Hirokazu; Kawamura, Hiroshi

2006-01-01

As a study about the joint technology of copper alloy and stainless steel for utilization as cooling piping in International Thermonuclear Experimental Reactor (ITER), Al 2 O 3 -dispersed strengthened copper or CuCrZr was jointed to stainless steel by three kinds of joint methods (casting joint, brazing joint and friction welding method) for the evaluation of the neutron irradiation effect on joints. A neutron irradiation test was performed to three types of joints and each copper alloy. The average value of fast neutron fluence in this irradiation test was about 2 x 10 24 n/m 2 (E>1 MeV), and the irradiation temperature was about 130degC. As post-irradiation examinations, tensile tests, hardness tests and observation of fracture surface after the tensile tests were performed. All type joints changed to be brittle by the neutron irradiation effect like each copper alloy material, and no particular neutron irradiation effect due to the effect of joint process was observed. On the casting and friction welding, hardness of copper alloy near the joint boundary changed to be lower than that of each copper alloy by the effect of joint procedure. However, tensile strength of joints was almost the same as that of each copper alloy before/after neutron irradiation. On the other hand, tensile strength of joints by brazing changed to be much lower than CuAl-25 base material by the effect of joint process before/after neutron irradiation. Results in this study showed that the friction welding method and the casting would be able to apply to the joint method of piping in ITER. This report is based on the final report of the ITER Engineering Design Activities (EDA). (author)

Report on surveys and researches to excavate international joint researches related to industrial technologies; Sangyo gijutsu ni kansuru kokusai kyodo kenkyu hakkutsu no tame no chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Five themes were taken up for a project of the 'surveys and researches to excavate international joint researches related to industrial technologies'. Investigation groups were organized and dispatched for each theme toperform domestic and overseas surveys. Discussions were given on eachtheme for the possibilities of structuring international joint researches. The five themes are as follows: 'wearable information network related technologies', wherein technologies to micronize information devices have been advanced rapidly, and the technologies are entering the age from personalizing and mobilizing the information into the wearable computing; this theme is intended to develop systems to unify these technologies by means of international joint researches: 'surveys on using unutilized animal oils and fats as chemical raw materials', which are intended to make clear possibilities and problems in utilizing animal oils and fats as raw materials for the chemical industry that can substitute fossil resources: 'international joint researches on new glasses' and 'processes to manufacture semiconductors using glassy carbon' to develop glassy carbon having excellent chemical resistance substituting quartz: and 'international joint researches on the Russian project which places environment and energy in its center'. (NEDO)

Formation of Exfoliation Joints

Science.gov (United States)

Martel, S. J.

2004-12-01

The Earth's internal stresses interact with the topographic surface to affect many phenomena. Exfoliation joints, or sheeting joints, are widespread manifestations of this interaction. These opening-mode fractures form subparallel to the Earth's surface, bounding roughly concentric slabs of rock that resemble the layers of an onion. They occur worldwide in all major bedrock types, attain in-plane dimensions of hundreds of meters, exert a strong influence on groundwater flow, and help produce spectacular scenery, as in Yosemite National Park. The mechanism that causes them has been enigmatic. They are widely regarded as forming in response to "removal of overburden", but large fractures do not open in rocks merely by relieving a compressive stress. High fluid pressures, thermal effects, rock heterogeneity, and weathering also are rejected as primary causes of these fractures. Tensile stresses normal to the surface are required for large exfoliation fractures to open. Intriguingly, high surface-parallel compressive stresses are widely documented where exfoliation joints occur. Both numerical and analytical solutions for two-dimensional elastic bodies show that localized tensile stresses perpendicular to the ground surface must develop beneath certain topographies subject to strong compressive stresses parallel to the surface. This highly non-intuitive effect reflects the profound influence that topography can have on stresses near the surface of the Earth, and it can explain how exfoliation joints open. The theoretical results also indicate that exfoliation joint distributions could be used to infer the horizontal stresses near the Earth's surface.

The impaired proprioception in Ehlers-Danlos Syndrome-Hypermobility Type/Joint hypermobility Syndrome: the rehabilitation role

Directory of Open Access Journals (Sweden)

Filippo Camerota

2015-10-01

Full Text Available Ehlers-Danlos Syndrome Hypermobility Type/Joint Hypermobility Syndrome (JHS/EDS-HT is an hereditary disorder of the connective tissue mainly manifesting with generalized joint hypermobility and skin hyperextensibility with an involvement of the connective tissue matrix proteins. Collagen alterations may influence the quality of movement in these patients but also movement has a role for the collagen quality: motion has a prevention role in the formation of contractures and adhesions. A poor sense of proprioception correlated with the collagenous connective tissues alterations could explain why people with JHS/EDS-HT become injured, having a lack of sensation of the joint at the end of the range. Rehabilitation approach may consider all these aspects.

Pierre Auger Observatory and Telescope Array: Joint Contributions to the 33rd International Cosmic Ray Conference (ICRC 2013)

NARCIS (Netherlands)

Telescope Array, The; Pierre Auger Collaborations,; Abu-Zayyad, T.; Allen, M.; Anderson, R.; Azuma, R.; Barcikowski, E.; Belz, J. W; Bergman, D. R.; Blake, S. A.; Cady, R.; Chae, M. J.; Cheon, B. G.; Chiba, J.; Chikawa, M.; Cho, W. R.; Fujii, T.; Fukushima, M.; Goto, K.; Hanlon, W.; Hayashi, Y.; Hayashida, N.; Hibino, K.; Honda, K.; Ikeda, D.; Inoue, N.; Ishii, T.; Ishimori, R.; Ito, H.; Ivanov, D.; Jui, C. C. H.; Kadota, K.; Kakimoto, F.; Kalashev, O.; Kasahara, K.; Kawai, H.; Kawakami, S.; Kawana, S.; Kawata, K.; Kido, E.; Kim, H. B.; Kim, J. H.; Kim, J. H.; Kitamura, S.; Kitamura, Y.; Kuzmin, V.; Kwon, Y. J.; Lan, J.; Lundquist, J. P.; Machida, K.; Martens, K.; Matsuda, T.; Matsuyama, T.; Matthews, J. N.; Minamino, M.; Mukai, K.; Myers, I.; Nagasawa, K.; Nagataki, S.; Nakamura, T.; Nanpei, H.; Nonaka, T.; Nozato, A.; Ogio, S.; Oh, S.; Ohnishi, M.; Ohoka, H.; Oki, K.; Okuda, T.; Ono, M.; Oshima, A.; Ozawa, S.; Park, I. H.; Pshirkov, M. S.; Rodriguez, D. C.; Rubtsov, G.; Ryu, D.; Sagawa, H.; Sakurai, N.; Sampson, A. L.; Scott, L. M.; Shah, P. D.; Shibata, F.; Shibata, T.; Shimodaira, H.; Shin, B. K.; Shirahama, T.; Smith, J. D.; Sokolsky, P.; Springer, R. W.; Stokes, B. T.; Stratton, S. R.; Stroman, T. A.; Takamura, M.; Takeda, M.; Taketa, A.; Takita, M.; Tameda, Y.; Tanaka, H.; Tanaka, K.; Tanaka, M.; Thomas, S. B.; Thomson, G. B.; Tinyakov, P.; Tkachev, I.; Tokuno, H.; Tomida, T.; Troitsky, S.; Tsunesada, Y.; Tsutsumi, K.; Uchihori, Y.; Udo, S.; Urban, F.; Vasiloff, G.; Wada, Y.; Wong, T.; Yamaoka, H.; Yamazaki, K.; Yang, J.; Yashiro, K.; Yoneda, Y.; Yoshida, S.; Yoshii, H.; Zollinger, R.; Zundel, Z.; Aab, A.; Abreu, P.; Aglietta, M.; Ahlers, M.; Ahn, E. J.; Albuquerque, I. F. M.; Allekotte, I.; Allen, J.; Allison, P.; Almela, A.; Alvarez Castillo, J.; Alvarez-Muniz, J.; Alves Batista, R.; Ambrosio, M.; Aminaei, A.; Anchordoqui, L.; Andringa, S.; Antivcic, T.; Aramo, C.; Arqueros, F.; Asorey, H.; Assis, P.; Aublin, J.; Ave, M.; Avenier, M.; Avila, G.; Badescu, A. M.; Barber, K. B.; Bardenet, R.; Baeuml, J.; Baus, C.; Beatty, J. J.; Becker, K. H.; Belletoile, A.; Bellido, J. A.; BenZvi, S.; Berat, C.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanco, F.; Blanco, M.; Bleve, C.; Blumer, H.; Bohacova, M.; Boncioli, D.; Bonifazi, C.; Bonino, R.; Borodai, N.; Brack, J.; Brancus, I.; Brogueira, P.; Brown, W. C.; Buchholz, P.; Bueno, A.; Burton, R. E.; Buscemi, M.; Caballero-Mora, K. S.; Caccianiga, B.; Caccianiga, L.; Candusso, M.; Caramete, L.; Caruso, R.; Castellina, A.; Cataldi, G.; Cazon, L.; Cester, R.; Cheng, S. H.; Chiavassa, A.; Chinellato, J. A.; Chudoba, J.; Cilmo, M.; Clay, R. W.; Cocciolo, G.; Colalillo, R.; Collica, L.; Coluccia, M. R.; Conceicao, R.; Contreras, F.; Cook, H.; Cooper, M. J.; Coutu, S.; Covault, C. E.; Criss, A.; Cronin, J.; Curutiu, A.; Dallier, R.; Daniel, B.; Dasso, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; De Domenico, M.; de Jong, S. J.; De La Vega, G.; de Mello Junior, W. J. M.; de Mello Neto, J. R. T.; De Mitri, I.; de Souza, V.; de Vries, K. D.; del Peral, L.; Deligny, O.; Dembinski, H.; Dhital, N.; Di Giulio, C.; Diaz, J. C.; Diaz Castro, M. L.; Diep, P. N.; Diogo, F.; Dobrigkeit, C.; Docters, W.; D'Olivo, J. C.; Dong, P. N.; Dorofeev, A.; dos Anjos, J. C.; Dova, M. T.; Ebr, J.; Engel, R.; Erdmann, M.; Escobar, C. O.; Espadanal, J.; Etchegoyen, A.; Facal San Luis, P.; Falcke, H.; Fang, K.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferguson, A. P.; Fick, B.; Figueira, J. M.; Filevich, A.; Filipcic, A.; Foerster, N.; Fox, B. D.; Fracchiolla, C. E.; Fraenkel, E. D.; Fratu, O.; Frohlich, U.; Fuchs, B.; Gaior, R.; Gamarra, R. F.; Gambetta, S.; Garcia, B.; Garcia Roca, S. T.; Garcia-Gamez, D.; Garcia-Pinto, D.; Garilli, G.; Gascon Bravo, A.; Gemmeke, H.; Ghia, P. L.; Giller, M.; Gitto, J.; Glaser, C.; Glass, H.; Gomez Albarracin, F.; Gomez Berisso, M.; Gomez Vitale, P. F.; Goncalves, P.; Gonzalez, J. G.; Gookin, B.; Gorgi, A.; Gorham, P.; Gouffon, P.; Grebe, S.; Griffith, N.; Grillo, A. F.; Grubb, T. D.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Hansen, P.; Harari, D.; Harrison, T. A.; Harton, J. L.; Haungs, A.; Hebbeker, T.; Heck, D.; Herve, A. E.; Hill, G. C.; Hojvat, C.; Hollon, N.; Homola, P.; Hoerandel, J. R.; Horvath, P.; Hrabovsky, M.; Huber, D.; Huege, T.; Insolia, A.; Isar, P. G.; Jansen, S.; Jarne, C.; Josebachuili, M.; Kadija, K.; Kambeitz, O.; Kampert, K. H.; Karhan, P.; Kasper, P.; Katkov, I.; Kegl, B.; Keilhauer, B.; Keivani, A.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Knapp, J.; Krause, R.; Krohm, N.; Kroemer, O.; Kruppke-Hansen, D.; Kuempel, D.; Kunka, N.; La Rosa, G.; LaHurd, D.; Latronico, L.; Lauer, R.; Lauscher, M.; Lautridou, P.; Le Coz, S.; Leao, M. S. A. B.; Lebrun, D.; Lebrun, P.; Leigui de Oliveira, M. A.; Letessier-Selvon, A.; Lhenry-Yvon, I.; Link, K.; Lopez, R.; Lopez Aguera, A.; Louedec, K.; Lozano Bahilo, J.; Lu, L.; Lucero, A.; Ludwig, M.; Lyberis, H.; Maccarone, M. C.; Macolino, C.; Malacari, M.; Maldera, S.; Maller, J.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Marin, V.; Maris, I. C.; Marquez Falcon, H. R.; Marsella, G.; Martello, D.; Martinez, H.; Martinez Bravo, O.; Martraire, D.; Masias Meza, J. J.; Mathes, H. J.; Matthews, J.; Matthews, J. A. J.; Matthiae, G.; Maurel, D.; Maurizio, D.; Mayotte, E.; Mazur, P. O.; Medina, C.; Medina-Tanco, G.; Melissas, M.; Melo, D.; Menichetti, E.; Menshikov, A.; Messina, S.; Meyhandan, R.; Micanovic, S.; Micheletti, M. I.; Middendorf, L.; Minaya, I. A.; Miramonti, L.; Mitrica, B.; Molina-Bueno, L.; Mollerach, S.; Monasor, M.; Monnier Ragaigne, D.; Montanet, F.; Morales, B.; Morello, C.; Moreno, J. C.; Mostafa, M.; Moura, C. A.; Muller, M. A.; Muller, G.; Munchmeyer, M.; Mussa, R.; Navarra, G.; Navarro, J. L.; Navas, S.; Necesal, P.; Nellen, L.; Nelles, A.; Neuser, J.; Nhung, P. T.; Niechciol, M.; Niemietz, L.; Niggemann, T.; Nitz, D.; Nosek, D.; Novzka, L.; Oehlschlager, J.; Olinto, A.; Oliveira, M.; Ortiz, M.; Pacheco, N.; Pakk Selmi-Dei, D.; Palatka, M.; Pallotta, J.; Palmieri, N.; Parente, G.; Parra, A.; Pastor, S.; Paul, T.; Pech, M.; Pekala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petermann, E.; Petrera, S.; Petrolini, A.; Petrov, Y.; Piegaia, R.; Pierog, T.; Pieroni, P.; Pimenta, M.; Pirronello, V.; Platino, M.; Plum, M.; Pontz, M.; Porcelli, A.; Preda, T.; Privitera, P.; Prouza, M.; Quel, E. J.; Querchfeld, S.; Quinn, S.; Rautenberg, J.; Ravel, O.; Ravignani, D.; Revenu, B.; Ridky, J.; Riggi, S.; Risse, M.; Ristori, P.; Rivera, H.; Rizi, V.; Roberts, J.; Rodrigues de Carvalho, W.; Rodriguez Cabo, I.; Rodriguez Fernandez, G.; Rodriguez Martino, J.; Rodriguez Rojo, J.; Rodriguez-Frias, M. D.; Ros, G.; Rosado, J.; Rossler, T.; Roth, M.; Rouille-d'Orfeuil, B.; Roulet, E.; Rovero, A. C.; Ruhle, C.; Saffi, S. J.; Saftoiu, A.; Salamida, F.; Salazar, H.; Salesa Greus, F.; Salina, G.; Sanchez, F.; Sanchez-Lucas, P.; Santo, C. E.; Santos, E.; Santos, E. M.; Sarazin, F.; Sarkar, B.; Sato, R.; Scharf, N.; Scherini, V.; Schieler, H.; Schiffer, P.; Schmidt, A.; Scholten, O.; Schoorlemmer, H.; Schovanek, P.; Schroeder, F. G.; Schulz, A.; Schulz, J.; Sciutto, S. J.; Scuderi, M.; Segreto, A.; Settimo, M.; Shadkam, A.; Shellard, R. C.; Sidelnik, I.; Sigl, G.; Sima, O.; Smialkowski, A.; Smida, R.; Snow, G. R.; Sommers, P.; Sorokin, J.; Spinka, H.; Squartini, R.; Srivastava, Y. N.; Stanic, S.; Stapleton, J.; Stasielak, J.; Stephan, M.; Straub, M.; Stutz, A.; Suarez, F.; Suomijarvi, T.; Supanitsky, A. D.; Susa, T.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Szuba, M.; Tapia, A.; Tartare, M.; Tacscuau, O.; Tcaciuc, R.; Thao, N. T.; Tiffenberg, J.; Timmermans, C.; Tkaczyk, W.; Todero Peixoto, C. J.; Toma, G.; Tomankova, L.; Tome, B.; Tonachini, A.; Torralba Elipe, G.; Torres Machado, D.; Travnicek, P.; Tridapalli, D. B.; Trovato, E.; Tueros, M.; Ulrich, R.; Unger, M.; Valdes Galicia, J. F.; Valino, I.; Valore, L.; van Aar, G.; van den Berg, A. M.; van Velzen, S.; van Vliet, A.; Varela, E.; Vargas Cardenas, B.; Varner, G.; Vazquez, J. R.; Vazquez, R. A.; Veberic, D.; Verzi, V.; Vicha, J.; Videla, M.; Villasenor, L.; Wahlberg, H.; Wahrlich, P.; Wainberg, O.; Walz, D.; Watson, A. A.; Weber, M.; Weidenhaupt, K.; Weindl, A.; Werner, F.; Westerhoff, S.; Whelan, B. J.; Widom, A.; Wieczorek, G.; Wiencke, L.; Wilczynska, B.; Wilczynski, H.; Will, M.; Williams, C.; Winchen, T.; Wundheiler, B.; Wykes, S.; Yamamoto, T.; Yapici, T.; Younk, P.; Yuan, G.; Yushkov, A.; Zamorano, B.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Zhou, J.; Zhu, Y.; Zimbres Silva, M.; Ziolkowski, M.; Martin, L.

2013-01-01

Joint contributions of the Pierre Auger and Telescope Array Collaborations to the 33rd International Cosmic Ray Conference, Rio de Janeiro, Brazil, July 2013: cross-calibration of the fluorescence telescopes, large scale anisotropies and mass composition.

Pierre Auger Observatory and Telescope Array: Joint Contributions to the 33rd International Cosmic Ray Conference (ICRC 2013)

Energy Technology Data Exchange (ETDEWEB)

Abu-Zayyad, T.; et al.

2013-10-02

Joint contributions of the Pierre Auger and Telescope Array Collaborations to the 33rd International Cosmic Ray Conference, Rio de Janeiro, Brazil, July 2013: cross-calibration of the fluorescence telescopes, large scale anisotropies and mass composition.

Efficacy of Arthrocentesis with Injection of Hyaluronic Acid in the Treatment of Internal Derangement of Temporomandibular Joint

Directory of Open Access Journals (Sweden)

Pramila Shakya

2010-07-01

Full Text Available This cross-sectional study was designed to find out the effect of arthrocentesis with injection hyaluronic acid in thetreatment of internal derangement of temporomandibular joint (TMJ ID for the restoration of TMJ function. The studyincluded 25 patients, aged 13 to 50 years with symptoms of TMJ pain and clicking during function and limited mouthopening. TMJ ID was assessed with clinical examination and conformed with MRI. Arthrocentesis was done withinsertion of two 21gauze needles in the upper joint compartment and joint lavaged with 200 ml of ringer’s lactate solutionand at the end 1ml of hyaluronic acid was injected. Intensity of TMJ pain and clicking was assessed using visual analogscale, maximum mouth opening, lateral jaw movement and protrusion were assessed with millimeter scale. All theparameters were measured before the procedure , immediately after the procedure then after 2 weeks, 1 month , 3 monthsand 6 months procedure. During 6 months follow-up, clinical examination and comparison of the results showed 84%reduction in TMJ pain, 92% improvement in mouth opening and clicking disappear in 80% of patients.Key words: TMJ pain; clicking; internal derangement; arthrocentesis; hyaluronic acid.DOI: 10.3329/bsmmuj.v3i1.5509BSMMU J 2010; 3(1: 18-22

Joint simulation of stationary grade and non-stationary rock type for quantifying geological uncertainty in a copper deposit

Science.gov (United States)

Maleki, Mohammad; Emery, Xavier

2017-12-01

In mineral resources evaluation, the joint simulation of a quantitative variable, such as a metal grade, and a categorical variable, such as a rock type, is challenging when one wants to reproduce spatial trends of the rock type domains, a feature that makes a stationarity assumption questionable. To address this problem, this work presents methodological and practical proposals for jointly simulating a grade and a rock type, when the former is represented by the transform of a stationary Gaussian random field and the latter is obtained by truncating an intrinsic random field of order k with Gaussian generalized increments. The proposals concern both the inference of the model parameters and the construction of realizations conditioned to existing data. The main difficulty is the identification of the spatial correlation structure, for which a semi-automated algorithm is designed, based on a least squares fitting of the data-to-data indicator covariances and grade-indicator cross-covariances. The proposed models and algorithms are applied to jointly simulate the copper grade and the rock type in a Chilean porphyry copper deposit. The results show their ability to reproduce the gradual transitions of the grade when crossing a rock type boundary, as well as the spatial zonation of the rock type.

Correlation between internal derangement and osteoarthrosis in the temporomandibular joint using magnetic resonance imaging

International Nuclear Information System (INIS)

Song, Haeng Un; Choi, Sun Young; Koh, Kwang Joon

2002-01-01

To evaluate the relationship between internal derangement and osteoarthrosis in the temporomandibular joint (TMJ) using magnetic resonance imaging (MRI). One hundred and six MR images of TMJs in 53 patients were evaluated. Disc displacements and osseous changes of the TMJs were assessed. Lateral and rotational disc displacements were also evaluated on coronal images. No significant differences in the frequency of osseous changes of the TMJs between disc displacement with reduction and disc displacement without reduction groups were found. The erosion of the condylar head and the sclerosis of the articular eminence were more frequent in the internal derangement group than in the no disc displacement group. The flattening was the most frequently observed osseous change of both the condylar head and articular eminence. The relationship between internal derangement and osteoarthrosis is obscure, but it is thought that both disorders adversely affect each other.

Correlation between internal derangement and osteoarthrosis in the temporomandibular joint using magnetic resonance imaging

Energy Technology Data Exchange (ETDEWEB)

Song, Haeng Un; Choi, Sun Young; Koh, Kwang Joon [School of Dentistry, Chonbuk National University, Jeonju (Korea, Republic of)

2002-12-15

To evaluate the relationship between internal derangement and osteoarthrosis in the temporomandibular joint (TMJ) using magnetic resonance imaging (MRI). One hundred and six MR images of TMJs in 53 patients were evaluated. Disc displacements and osseous changes of the TMJs were assessed. Lateral and rotational disc displacements were also evaluated on coronal images. No significant differences in the frequency of osseous changes of the TMJs between disc displacement with reduction and disc displacement without reduction groups were found. The erosion of the condylar head and the sclerosis of the articular eminence were more frequent in the internal derangement group than in the no disc displacement group. The flattening was the most frequently observed osseous change of both the condylar head and articular eminence. The relationship between internal derangement and osteoarthrosis is obscure, but it is thought that both disorders adversely affect each other.

Chewing movements altered in the presence of temporomandibular joint internal derangements.

Science.gov (United States)

Radke, John C; Kull, Robert S; Sethi, Manminder S

2014-07-01

The objectives were to find specific factors that are mathematically distinct between the chewing timings, movement pattern shapes, variability, and movement velocities of: (1) normal asymptomatic subjects and (2) a group of subjects with verified temporomandibular joint (TMJ) internal derangements. Left- and right-sided chewing movement recordings of 28 subjects (34.5 ± 14.0 years) were randomly selected from a large database of patients exhibiting verified unilateral or bilateral TMJ internal derangements. The chewing movements of an age- and gender-matched control group of 20 asymptomatic subjects (32.5 ± 11.6 years, P>0.60) with verified normal TMJ function were also recorded. Means and standard deviations of the opening, closing, turning point, terminal chewing position, and velocity patterns were calculated. A two-tailed Student's t-test with unequal variances was used to compare the parameters between the two groups (alpha = 0.05). The dysfunctional group functioned significantly slower and with greater variability than the control group. The vertical dimension was consistently smaller in the dysfunctional group (Pchewing position was significantly less precise in the dysfunctional group (vertical: Pchewing patterns than the control group. The functional pattern of mastication appears to be significantly altered in the presence of an internal derangement of the TMJ.

Adaptive Shape Functions and Internal Mesh Adaptation for Modelling Progressive Failure in Adhesively Bonded Joints

Science.gov (United States)

Stapleton, Scott; Gries, Thomas; Waas, Anthony M.; Pineda, Evan J.

2014-01-01

Enhanced finite elements are elements with an embedded analytical solution that can capture detailed local fields, enabling more efficient, mesh independent finite element analysis. The shape functions are determined based on the analytical model rather than prescribed. This method was applied to adhesively bonded joints to model joint behavior with one element through the thickness. This study demonstrates two methods of maintaining the fidelity of such elements during adhesive non-linearity and cracking without increasing the mesh needed for an accurate solution. The first method uses adaptive shape functions, where the shape functions are recalculated at each load step based on the softening of the adhesive. The second method is internal mesh adaption, where cracking of the adhesive within an element is captured by further discretizing the element internally to represent the partially cracked geometry. By keeping mesh adaptations within an element, a finer mesh can be used during the analysis without affecting the global finite element model mesh. Examples are shown which highlight when each method is most effective in reducing the number of elements needed to capture adhesive nonlinearity and cracking. These methods are validated against analogous finite element models utilizing cohesive zone elements.

Corrosion and microstructural aspects of dissimilar joints of titanium and type 304L stainless steel

International Nuclear Information System (INIS)

Mudali, U. Kamachi.; Ananda Rao, B.M.; Shanmugam, K.; Natarajan, R.; Raj, Baldev

2003-01-01

To link titanium and zirconium metal based (Ti, Zr-2, Ti-5%Ta, Ti-5%Ta-1.8Nb) dissolver vessels containing highly radioactive and concentrated corrosive nitric acid solution to other nuclear fuel reprocessing plant components made of AISI type 304L stainless steel (SS), high integrity and corrosion resistant dissimilar joints between them are necessary. Fusion welding processes produce secondary precipitates which dissolve in nitric acid, and hence solid-state processes are proposed. In this work, various dissimilar joining processes available for producing titanium-304L SS joints with adequate strength, ductility and corrosion resistance for this critical application are highlighted. Developmental efforts made at IGCAR, Kalpakkam are outlined. The possible methods and the microstructural-metallurgical properties of the joints along with corrosion results obtained with three phase (liquid, vapour, condensate) corrosion testing are discussed. Based on the results, dissimilar joint produced by the explosive joining process was adopted for plant application

PREFACE: Joint Varenna-Lausanne International Workshop 2014

Science.gov (United States)

2014-11-01

The 2014 joint Varenna-Lausanne international workshop on the theory of fusion plasmas was once more a great meeting. The programme covers a wide variety of topics, namely turbulence, MHD, edge physics and RF wave heating. The broad spectrum of skills involved in this meeting, from fundamental to applied physics, is striking. The works published in this special issue combine mathematics, numerics and physics at various levels - confirming the increasing integration of expertise in our community. As an incentive to read this cluster, let us mention a few outstanding results. Several papers address fundamental issues in turbulent transport, in particular the dynamics of structures. It is quite remarkable that this subject is now mature enough to propose signatures that can be tested by measurements. Linear and non linear MHD was also at the forefront. Several works illustrate the increasing level of realistic description of a fusion device, in particular by implementing complicated wall geometries. Moreover some noticeable progress has been made in the understanding of reconnection processes in collisionless regimes. The activity on radio-frequency heating and current drive is well represented, driven by the future operation of W7-X, ITER, and DEMO on a longer time scale. Finally the development of innovative numerical techniques, an old tradition of the conference, has driven several nice articles. The programme committee is traditionally keen in promoting young scientists. A number of senior scientists also attend the meeting on a regular basis, so that the attendance was nicely balanced. We believe that these efforts have been particularly fruitful this year. The number of young (and less young) faces was particularly impressive and this special issue illustrates this feature. The success of the 2014 edition brings evidence that the joint Varenna-Lausanne is the right place for presenting th The quality and size of the scientific production is illustrated by the

Preliminary reports on fiscal 2000 results of project for subsidizing international joint research; 2000 nendo kokusai kyodo kenkyu josei jigyo seika hokoku kai yokoshu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-12-01

This paper presents preliminary reports on fiscal 2000 results of project for subsidizing international joint research sponsored by NEDO. For international joint research teams doing excellent studies, their research expenses are subsidized, thereby promoting international research exchange, enhancing international level of industrial technology and contributing to the formation of basis for innovative industrial technology. The projects relating to the global environmental field are implemented jointly with RITE. The contents of the report to be published are, in the global environmental field (practicability study), development of oil substitute resources, reproducible resources, and technologies for producing polymeric and plastic materials benign to the earth by microorganism using carbon dioxide. In the substance/material field, the contents of the report are innovative production and device application of tunable photonic crystals using electronic penetration network; development of new synthesis process of innovative nitride, creation and theoretical calculation of electromagnetic function; studies on quantum transportation in superconductor and semiconductor bonding structures; and studies on quantum liquid and solid, and application to materials science and technology. (NEDO)

Manual for IRS Coding. Joint IAEA/NEA International Reporting System for Operating Experience

International Nuclear Information System (INIS)

2011-01-01

The International Reporting System for Operating Experience (IRS) is jointly operated by the International Atomic Energy Agency (IAEA) and the Nuclear Energy Agency of the Organisation for Economic Co-operation and Development (OECD/NEA). In early 2010, the IAEA and OECD/NEA jointly issued the IRS Guidelines, which described the reporting system and process and gave users the necessary elements to enable them to produce IRS reports to a high standard of quality while retaining the effectiveness of the system expected by all Member States operating nuclear power plants. The purpose of the present Manual for IRS Coding is to provide supplementary guidance specifically on the coding element of IRS reports to ensure uniform coding of events that are reported through IRS. This Coding Manual does not supersede the IRS Guidelines, but rather, supports users and preparers in achieving a consistent and high level of quality in their IRS reports. Consistency and high quality in the IRS reports allow stakeholders to search and retrieve specific event information with ease. In addition, well-structured reports also enhance the efficient management of the IRS database. This Coding Manual will give specific guidance on the application of each section of the IRS codes, with examples where necessary, of when and how these codes are to be applied. As this reporting system is owned by the Member States, this manual has been developed and approved by the IRS National Coordinators with the assistance of the IAEA and NEA secretariats

26 CFR 1.6015-1 - Relief from joint and several liability on a joint return.

Science.gov (United States)

2010-04-01

... they claim losses attributable to H's limited partnership interest in Partnership A. In January 2006... 26 Internal Revenue 13 2010-04-01 2010-04-01 false Relief from joint and several liability on a... joint and several liability on a joint return. (a) In general. (1) An individual who qualifies and...

The Cultural Context of Learning in International Joint Ventures.

Science.gov (United States)

Liu, Shimin; Vince, Russ

1999-01-01

A study of Chinese-Western joint business ventures showed that cultural context and different modes of managing and organizing must be considered. Successful joint ventures involve a process of collective, two-way learning. (SK)

Subjective health complaints and illness perception amongst adults with Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome-HypermobilityType - a cross-sectional study.

Science.gov (United States)

Hope, Lena; Juul-Kristensen, Birgit; Løvaas, Helene; Løvvik, Camilla; Maeland, Silje

2017-10-17

To investigate the prevalence and severity of subjective health complaints and describe illness perception in a population of Joint Hypermobility Syndrome or Ehlers-Danlos Syndrome-Hypermobile Type. This study was a postal survey with a questionnaire battery on demographic data, subjective health complaints inventory, and illness perception. A total of 110 individuals diagnosed with Joint Hypermobility Syndrome or Ehlers-Danlos Syndrome-Hypermobile Type from two specialized hospitals in Norway were offered participation. Further, 140 gender- and age-matched healthy controls from statistics Norway representing the general population were sent the questionnaire for reference. Overall response rate was 30.4% (n = 76), with 44.5% (n = 49) in Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome-Hypermobile Type and 19.3% (n = 27) in controls. Subjective health complaints were significantly higher in Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome-Hypermobile Type - than in the controls (32.06 vs. 11.08; p Syndrome/Ehlers-Danlos Syndrome-Hypermobile Type had low understanding of their illness and symptoms (understanding, mean: 3.93, SD 2.88), and reported to have moderate personal and treatment control over their illness. Adults with Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome-Hypermobile Type reported higher frequency and severity of subjective health complaints than the matched controls from the general adult population in Norway. Furthermore, Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome-Hypermobile Type reported low understanding of their illness and associated symptoms, and moderate belief that their illness can be kept under control through self-management or treatment. This may indicate one of the reasons why prognosis for these patients is poor. Implications for rehabilitation Awareness of the complexity of the subjective health complaints and inquiry into illness perception could contribute with valuable information about these

Refining patterns of joint hypermobility, habitus, and orthopedic traits in joint hypermobility syndrome and Ehlers-Danlos syndrome, hypermobility type.

Science.gov (United States)

Morlino, Silvia; Dordoni, Chiara; Sperduti, Isabella; Venturini, Marina; Celletti, Claudia; Camerota, Filippo; Colombi, Marina; Castori, Marco

2017-04-01

Joint hypermobility syndrome (JHS) and Ehlers-Danlos syndrome, hypermobility type (EDS-HT) are two overlapping heritable disorders (JHS/EDS-HT) recognized by separated sets of diagnostic criteria and still lack a confirmatory test. This descriptive research was aimed at better characterizing the clinical phenotype of JHS/EDS-HT with focus on available diagnostic criteria, and in order to propose novel features and assessment strategies. One hundred and eighty-nine (163 females, 26 males; age: 2-73 years) patients from two Italian reference centers were investigated for Beighton score, range of motion in 21 additional joints, rate and sites of dislocations and sprains, recurrent soft-tissue injuries, tendon and muscle ruptures, body mass index, arm span/height ratio, wrist and thumb signs, and 12 additional orthopedic features. Rough rates were compared by age, sex, and handedness with a series of parametric and non-parametric tools. Multiple correspondence analysis was carried out for possible co-segregations of features. Beighton score and hypermobility at other joints were influenced by age at diagnosis. Rate and sites of joint instability complications did not vary according to age at diagnosis except for soft-tissue injuries. No major difference was registered by sex and dominant versus non-dominant body side. At multiple correspondence analysis, selected features tend to co-segregate in a dichotomous distribution. Dolichostenomelia and arachnodactyly segregated independently. This study pointed out a more protean musculoskeletal phenotype than previously considered according to available diagnostic criteria for JHS/EDS-HT. Our findings corroborated the need for a re-thinking of JHS/EDS-HT on clinical grounds in order to find better therapeutic and research strategies. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

12 CFR 347.107 - Joint ventures.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Joint ventures. 347.107 Section 347.107 Banks... INTERNATIONAL BANKING § 347.107 Joint ventures. (a) Joint ventures. If a bank, directly or indirectly, acquires or holds an equity interest in a foreign organization that is a joint venture, and the bank or its...

Reinforcement of Bolted Timber Joints Using GFRP Sheets in Poplar and Pine Woods

Directory of Open Access Journals (Sweden)

Mehrab Madhoushi

2013-01-01

Full Text Available Failure in timber structures occurs mainly in crucial points such as joints areas. Therefore, the idea of using composite sheets in timber joints has been intro-duced as a method in order to increase the strength and ductility behaviour of timber joints. This research aims to study the behaviour of bolted joints in poplar and pine woods, which are reinforced by two types of GFRP sheets. A single shear bolted joint consisted of 3 timber members whose length and width were 30 cm in length and 5 cm in width. The thickness of each member was 4 cm for internal part and 2 cm for external part. The employed steel bolt was 10 cm in length and 1 cm in diameter. In this respect, one layer of GFRP sheet was used to be bonded to timber members by using epoxy resin and left between the clamps for 24 hours. They were then kept at room temperature for three weeks. Also the effect of adding a wood veneer on the reinforced joints was investigated. The tensile strength of the reinforced and control samples (un-reinforced joints was measured according to ASTM D5652-92 standard. The results show that the reinforced samples have higher tensile strength compared to that of reinforced joints, although it is not statistically signifcant. Also, two types of sheets infuence the joint behaviour as the reinforced joints display more ductility behaviour.

Invited and contributed papers presented by the theory group at the joint Varenna-Lausanne international workshop 'theory of fusion plasmas'

International Nuclear Information System (INIS)

1996-09-01

In this report eight invited and contributed papers of the theory group are included which were presented at joint Varenna-Lausanne international workshop on 'theory of fusion plasmas'. (author) figs., tabs., refs

CT of the temporomandibular joint: The conservative approach

International Nuclear Information System (INIS)

Jend, H.H.; Jend-Rossmann, I.; Heller, M.

1986-01-01

Until recently, CT investigation of temporomandibular joint (TMJ) disorders has been regarded as a sophisticated procedure. A method of investigation was developed that allows easy evaluation of axial scans. The method was evaluated in a series of 65 joints with arthrographically diagnosed internal derangements. In anterior disk displacement CT findings led to an identical diagnosis in 56 of 65 joints (sensitivity, 86%). In clinically asymptomatic joints investigated for other reasons, only one of 12 showed signs of internal derangement on CT (specificity, 92%). This conservative approach to CT evaluation of internal derangement seems to be as accurate as more sophisticated methods. It is easy to perform, requires no additional manpower or computer time, and has a very good reproducibility

Joint radiation emergency management plan of the international organizations. Emergency preparedness and response. Date effective: 1 December 2002

International Nuclear Information System (INIS)

2002-11-01

directives and regulations that bear on emergency response arrangements among some States. There are also bilateral agreements between some international organizations that also have relevance to preparedness and response arrangements. In March 2002, the IAEA Board of Governors approved a Safety Requirements document to be issued according to the IAEA's statutory function 'to establish ... standards of safety for protection of health and minimization of danger to life and property'. These Safety Requirements, entitled 'Preparedness and Response for a Nuclear or Radiological Emergency' (GS-R-2), are being jointly sponsored by the FAO, IAEA, the International Labour Organisation (ILO), the OECD Nuclear Energy Agency (NEA/OECD), the United Nations Office for the Co-ordination of Humanitarian Affairs (OCHA), the Pan American Health Organization (PAHO) and WHO. These safety standards imply additional expectations with regard to operational emergency response arrangements. It has been recognized by the organizations responsible for emergency response, and reflected in the above requirements, that good planning in advance of an emergency can substantially improve the response. Moreover, one of the most important features of emergency response plans is to have clear lines of responsibility and authority. With this in mind, the IAEA, the organizations party to the Conventions, and some other international organizations that participate in the activities of the IACRNA develop and maintain this 'Joint Radiation Emergency Management Plan of the International Organizations' (the Joint Plan), which describes: the objectives of response; the organizations involved in response, their roles and responsibilities, and the interfaces among them and between them and States; operational concepts; and preparedness arrangements. These practical arrangements are reflected in the various organizations own emergency plans. The IAEA is the main co-ordinating body for development and maintenance of the

Internal derangements of the temporomandibular joint: A review of the anatomy, diagnosis, and management

Directory of Open Access Journals (Sweden)

Andrew L Young

2015-01-01

Full Text Available Internal derangements of the temporomandibular joint are conditions in which the articular disc has become displaced from its original position the condylar head. Relevant anatomic structures and their functional relationships are briefly discussed. The displacement of the disc can result in numerous presentations, with the most common being disc displacement with reduction (with or without intermittent locking, and disc displacement without reduction (with or without limited opening. These are described in this article according to the standardized Diagnostic Criteria for Temporomandibular Disorders, as well as the less common posterior disc displacement. Appropriate management usually ranges from patient education and monitoring to splints, physical therapy, and medications. In rare and select cases, surgery may be necessary. However, in for the majority of internal derangements, the prognosis is good, particularly with conservative care.

22 CFR 228.34 - Joint ventures.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Joint ventures. 228.34 Section 228.34 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT RULES ON SOURCE, ORIGIN AND NATIONALITY FOR COMMODITIES AND... Financing § 228.34 Joint ventures. A joint venture or unincorporated association is eligible only if each of...

Open capsular and ligament reconstruction with semitendinosus hamstring autograft successfully controls superior and posterior translation for type V acromioclavicular joint dislocation.

Science.gov (United States)

Garofalo, Raffaele; Ceccarelli, Enrico; Castagna, Alessandro; Calvisi, Vittorio; Flanagin, Brody; Conti, Marco; Krishnan, Sumant G

2017-07-01

Appropriate surgical management for type V complete acromioclavicular (AC) joint dislocation remains controversial. The purpose of this paper is to retrospectively report the clinical and radiographic outcomes of an open surgical technique consisting for AC joint ligamentous and capsular reconstruction using autologous hamstring tendon grafts and semi-permanent sutures. Between January 2005 and December 2011, 32 consecutive patients with symptomatic type V complete AC joint dislocation underwent surgical treatment using the same technique. The median time from injury to surgery was 45 days (range 24-90). The average median postoperative clinical and radiographic follow-up time was 30 months (range 24-33). Clinical outcomes measures included the ASES score, the visual analog score (VAS), and subjective patient satisfaction score. Minimum follow-up was 2 years. ASES score increased from a median of 38.2 ± 6.2 preoperative to 92.1 ± 4.7 postoperatively (p ≤ 0.05). The median VAS score improved from 62 mm (range 45-100 mm) preoperatively to 8 mm (range 0-20 mm) at final follow-up (p ≤ 0.05). No patient experienced pain or discomfort with either direct palpation of the AC joint or with cross-body adduction. Final radiographs demonstrated symmetric AC joint contour in 25/32 (78%) patients. Seven patients (22%) radiographically demonstrated superior translation of the distal clavicle relative to the superior margin of the acromion but less than 50% of the clavicular width. 30/32 patients (93%) were able to return to their pre-injury level of work and sports activities. This novel surgical technique using a free graft and braided suture for simultaneous coracoclavicular ligament and AC joint capsular reconstruction successfully controls superior and posterior translations after type V AC joint dislocation and minimizes the incidence of persistent postoperative AC joint subluxation. Retrospective case series, Level IV.

BioSTEC 2017: 10th International Joint Conference on Biomedical Engineering Systems and Technologies : Proceedings Volume 5: HealthInf

NARCIS (Netherlands)

2017-01-01

This book contains the proceedings of the 10th International Joint Conference on Biomedical Engineering Systems and Technologies (BIOSTEC 2017). This conference is sponsored by the Institute for Systems and Technologies of Information, Control and Communication (INSTICC), in cooperation with the ACM

Report on the SNL/AWE/NSF international workshop on joint mechanics, Dartington, United Kingdom, 2729 April 2009.

Energy Technology Data Exchange (ETDEWEB)

Ewins, David J. (University of Bristol, UK); Bergman, Lawrence A. (University of Illinois, Urbana, IL); Segalman, Daniel Joseph

2010-08-01

The SNL/AWE joint mechanics workshop, held in Dartington Hall, Totnes, Devon, UK 26-29 April 2009 was a follow up to another international joints workshop held in Arlington, Virginia, in October 2006. The preceding workshop focused on identifying what length scales and interactions would be necessary to provide a scientific basis for analyzing and understanding joint mechanics from the atomistic scale on upward. In contrast, the workshop discussed in this report, focused much more on identification and development of methods at longer length scales that can have a nearer term impact on engineering analysis, design, and prediction of the dynamics of jointed structures. Also, the 2009 meeting employed less technical presentation and more break out sessions for developing focused strategies than was the case with the early workshop. Several 'challenges' were identified and assignments were made to teams to develop approaches to address those challenges.

Periprosthetic joint infection: are patients with multiple prosthetic joints at risk?

Science.gov (United States)

Jafari, S Mehdi; Casper, David S; Restrepo, Camilo; Zmistowski, Benjamin; Parvizi, Javad; Sharkey, Peter F

2012-06-01

Patients who present with a periprosthetic joint infection in a single joint may have multiple prosthetic joints. The risk of these patients developing a subsequent infection in another prosthetic joint is unknown. Our purposes were (1) to identify the risk of developing a subsequent infection in another prosthetic joint and (2) to describe the time span and organism profile to the second prosthetic infection. We retrospectively identified 55 patients with periprosthetic joint infection who had another prosthetic joint in place at the time of presentation. Of the 55 patients, 11 (20%) developed a periprosthetic joint infection in a second joint. The type of organism was the same as the first infection in 4 (36%) of 11 patients. The time to developing a second infection averaged 2.0 years (range, 0-6.9 years). Copyright © 2012 Elsevier Inc. All rights reserved.

Comorbidity of internal derangement of the temporomandibular joint and silent dysfunction of the cervical spine.

Science.gov (United States)

Stiesch-Scholz, M; Fink, M; Tschernitschek, H

2003-04-01

The aim of this evaluation was to examine correlations between internal derangement of the temporomandibular joint (TMJ) and cervical spine disorder (CSD). A prospective controlled clinical study was carried out. Thirty patients with signs and symptoms of internal derangement but without any subjective neck problems and 30 age- and gender-matched control subjects without signs and symptoms of internal derangement were examined. The investigation of the temporomandibular system was carried out using a 'Craniomandibular Index'. Afterwards an examiner-blinded manual medical investigation of the craniocervical system was performed. This included muscle palpation of the cervical spine and shoulder girdle as well as passive movement tests of the cervical spine, to detect restrictions in the range of movement as well as segmental intervertebral dysfunction. The internal derangement of the TMJ was significantly associated with 'silent' CSD (t-test, P temporomandibular system exhibited significantly more often pain on pressure of the neck muscles than patients without muscle tenderness of the temporomandibular system (t-test, P < 0.05). As a result of the present study, for patients with internal derangement of the TMJ an additional examination of the craniocervical system should be recommended.

Joint design of QC-LDPC codes for coded cooperation system with joint iterative decoding

Science.gov (United States)

Zhang, Shunwai; Yang, Fengfan; Tang, Lei; Ejaz, Saqib; Luo, Lin; Maharaj, B. T.

2016-03-01

In this paper, we investigate joint design of quasi-cyclic low-density-parity-check (QC-LDPC) codes for coded cooperation system with joint iterative decoding in the destination. First, QC-LDPC codes based on the base matrix and exponent matrix are introduced, and then we describe two types of girth-4 cycles in QC-LDPC codes employed by the source and relay. In the equivalent parity-check matrix corresponding to the jointly designed QC-LDPC codes employed by the source and relay, all girth-4 cycles including both type I and type II are cancelled. Theoretical analysis and numerical simulations show that the jointly designed QC-LDPC coded cooperation well combines cooperation gain and channel coding gain, and outperforms the coded non-cooperation under the same conditions. Furthermore, the bit error rate performance of the coded cooperation employing jointly designed QC-LDPC codes is better than those of random LDPC codes and separately designed QC-LDPC codes over AWGN channels.

Three types of communication on internal social media:

DEFF Research Database (Denmark)

Madsen, Vibeke Thøis

The aim of this paper is to explore to what extend internal social media introduces a new kind of participatory communication in organizations. The paper is based on two explorative studies: A multiple case study in ten Danish organizations and a single case study in a Danish bank. Based on the two...... studies it is proposed that it is possible to distinguish between three different types of communication arenas created by internal social media: A quiet arena, a knowledge sharing arena and a participatory communication arena. Internal social media does not in itself introduce participatory communication....... Different levels of communication might be reached in different types of organizations, and it is only when coworkers perceive a license to critique that organizations will actually develop participatory communication that has the ability to move the organization....

Neurodevelopmental attributes of joint hypermobility syndrome/Ehlers-Danlos syndrome, hypermobility type: Update and perspectives.

Science.gov (United States)

Ghibellini, Giulia; Brancati, Francesco; Castori, Marco

2015-03-01

In the last decade, increasing attention has been devoted to the extra-articular and extra-cutaneous manifestations of joint hypermobility syndrome, also termed Ehlers-Danlos syndrome, hypermobility type (i.e., JHS/EDS-HT). Despite the fact that the current diagnostic criteria for both disorders remain focused on joint hypermobility, musculoskeletal pain and skin changes, medical practice and research have started investigating a wide spectrum of visceral, neurological and developmental complications, which represent major burdens for affected individuals. In particular, children with generalized joint hypermobility often present with various neurodevelopmental issues and can be referred for neurological consultation. It is common that investigations in these patients yield negative or inconsistent results, eventually leading to the exclusion of any structural neurological or muscle disorder. In the context of specialized clinics for connective tissue disorders, a clear relationship between generalized joint hypermobility and a characteristic neurodevelopmental profile affecting coordination is emerging. The clinical features of these patients tend to overlap with those of developmental coordination disorder and can be associated with learning and other disabilities. Physical and psychological consequences of these additional difficulties add to the chief manifestations of the pre-existing connective tissue disorder, affecting the well-being and development of children and their families. In this review, particular attention is devoted to the nature of the link between joint hypermobility, coordination difficulties and neurodevelopmental issues in children. Presumed pathogenesis and management issues are explored in order to attract more attention on this association and nurture future clinical research. © 2015 Wiley Periodicals, Inc.

Intra-articular calcaneal fractures: effect of open reduction and internal fixation on the contact characteristics of the subtalar joint.

Science.gov (United States)

Mulcahy, D M; McCormack, D M; Stephens, M M

1998-12-01

Intra-articular calcaneal fractures are associated with significant long-term morbidity, and considerable controversy exists regarding the optimum method of treating them. The contact characteristics in the intact subtalar joint were determined at known loads and for different positions of the ankle and subtalar joint, using pressure-sensitive film (Super Low; Fuji, Itochu Canada Ltd, Montreal, Quebec). We measured the contact area to joint area ratio (pressure > 5 kg force/cm2 [kgf/cm2]) which normalizes for differences in joint size and the ratio of high pressure zone (>20 kgf/cm2) as a reflection of overall increase in joint pressure. Three simulated fracture patterns were then created and stabilized with either 1 or 2 mm of articular incongruity. Eight specimens were prepared with a primary fracture line through the posterior facet, eight with a joint depression-type fracture, and six with a central joint depression fracture. A measure of 1 to 2 mm of incongruity in the posterior facet for all three fracture patterns produced significant unloading of the depressed fragment, with a redistribution of the overall pattern of pressure distribution to parts of the facet that were previously unloaded.

Radiographic evaluation of cervical spine of subjects with temporomandibular joint internal disorder.

Science.gov (United States)

Munhoz, Wagner Cesar; Marques, Amélia Pasqual; Siqueira, José Tadeu Tesseroli de

2004-01-01

Although the etiopathophysiology of internal temporomandibular joint internal disorders (TMJ ID) is still unknown, it has been suggested that head and body posture could be related to its initial onset, development and perpetuation. The purpose of the present study was to observe the relationship between cervical spine X-ray abnormalities and TMJ ID. This investigation evaluated 30 subjects with internal TMJ disorder symptoms (test group) and 20 healthy subjects (control group). Subjects were submitted to clinical and radiographic evaluation. Clinical evaluation comprised anamnesis and stomatognathic system physical examination. Radiographic evaluation comprised analysis of lateral cervical spine X-rays by three physical therapists and tracing on the same images. The test group presented twice as much cervical spine hyperlordosis as the control group (20.7% versus 10.5%), but almost half of rectification prevalence (41.4 versus 79.0%, p = 0.03). After that, the test group was divided into three subgroups according to TMJ dysfunction severity, evaluated by Helkimo's index. These subgroups were not significantly different, but the subgroup with more severe TMD showed a tendency to cervical spine hyperlordosis prevalence. Results showed a tendency for subjects with more severe TMD to exhibit cervical spine hyperlordosis. Nevertheless, studies with a larger number of subjects suffering from severe TMD are encouraged in order to corroborate the present findings.

Reliability of Tubular Joints

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard; Thoft-Christensen, Palle

In this paper the preliminary results obtained by tests on tubular joints are presented. The joints are T-joints and the loading is static. It is the intention in continuation of these tests to perform tests on other types of joints (e.g. Y-joints) and also with dynamic loading. The purpose...... of the test is partly to obtain empirical data for the ultimate load-carrying capacity of tubular T-joints and partly to obtain some experience in performing tests with tubular joints. It is well known that tubular joints are usually designed in offshore engineering on the basis of empirical formulas obtained...... by experimental test results. Therefore, there is a need for performing experimental tests in this area....

Joint nuclear safety research projects between the US and Russian Federation International Nuclear Safety Centers

International Nuclear Information System (INIS)

Bougaenko, S.E.; Kraev, A.E.; Hill, D.L.; Braun, J.C.; Klickman, A.E.

1998-01-01

The Russian Federation Ministry for Atomic Energy (MINATOM) and the US Department of Energy (USDOE) formed international Nuclear Safety Centers in October 1995 and July 1996, respectively, to collaborate on nuclear safety research. Since January 1997, the two centers have initiated the following nine joint research projects: (1) INSC web servers and databases; (2) Material properties measurement and assessment; (3) Coupled codes: Neutronic, thermal-hydraulic, mechanical and other; (4) Severe accident management for Soviet-designed reactors; (5) Transient management and advanced control; (6) Survey of relevant nuclear safety research facilities in the Russian Federation; (8) Advanced structural analysis; and (9) Development of a nuclear safety research and development plan for MINATOM. The joint projects were selected on the basis of recommendations from two groups of experts convened by NEA and from evaluations of safety impact, cost, and deployment potential. The paper summarizes the projects, including the long-term goals, the implementing strategy and some recent accomplishments for each project

The joint choice of tenure, dwelling type and size

DEFF Research Database (Denmark)

Frenkel, Amnon; Bendit, Eduard; Kaplan, Sigal

Real-estate market trends regarding housing preferences for tenure, dwelling type and size carry long term implications for cities’ spatial development and compactness. Much attention have been given to the impact of household demographics and socio-economic characteristics on joint housing choices...... not ignore the ordered nature of apartment size. To the best of our knowledge, first application of the MNL-OR model in the context of housing preferences. The model is applied to a data sample of 833 knowledge-workers in the Tel-Aviv metropolitan region in Israel. The effect of lifestyle on housing...... preferences is particularly interesting in the case of knowledge-workers due to their high income and car ownership which allow high residential mobility, and due to the importance they attribute to lifestyle. The data were collected by means of a revealed-preference web-based survey that elicited information...

Overview of the IAEA Joint Convention and Implementation Status of the Obligation as the Contracting Party of the 5th Joint Convention

International Nuclear Information System (INIS)

Lee, Jeong Ken; Lee, Youn Keun; Ahn, Sang Myeon

2016-01-01

The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (Joint Convention) was adopted on 5 September 1997 by a Diplomatic Conference convened by the International Atomic Energy Agency (IAEA). The Joint Convention was opened for signature at Vienna in September 1997 and will remain open for signature until its entry into force. Korean government signed the Joint Convention in 1997 and this Convention was effective in 2002 as the Convention No. 1612. This paper will show overview of the Joint Convention and implementation status of the obligation as a Contracting Party of the 5th Joint Convention. The Joint Convention is the inter-national convention organized by the IAEA. All contracting parties shall comply with rules of the Joint Convention and conduct the obligation of this convention. Korean government successfully conducted all obligation (attending Organization Meeting and Review Meeting, submitting paper including National Report, question paper and answer paper) of the 5th Joint Convention from May 2014 to May 2015, and will prepare the obligation of the 6th Joint Convention

The Zeitgeist of Challenging the Evidence. A Perspective on the International Consensus Meeting on Periprosthetic Joint Infection

Directory of Open Access Journals (Sweden)

Hangama C. Fayaz

2017-01-01

Full Text Available Background: The economic burden of the treatment of periprosthetic joint infection (PJI is high and the treatment of PJI has a high degree of international controversy. Several papers have declared the International Consensus Meeting on Periprosthetic Joint Infection (ICMPJI to be the "flawless pledge of international academics" to overcome the challenges of musculoskeletal infections. The purpose of this paper is to highlight for the first time some essential insights into the key dilemmas that are associated with this international consensus process. Methods: The proceedings of the ICMPJI was reviewed, and the critical consensus agreements that were reached were communicated via e-mail to 48 leading orthopaedic surgeons, microbiologists and statisticians around the world. Of these, 30 responded, 8 did not, and 10 of respondents were not aware of the ICMPJI. Results: A thorough review of the ICMPJI proceedings identified a clear need to resolve some of the dilemmas that we highlight in this paper. The Delphi procedure has been described as a survey technique that enables a group dynamic-based practice. Although there have been several published reports on this procedure, its scientific merit is still being debated. Several challenges and questions have been raised regarding the application of the Delphi technique, but there is no doubt that it is a vital approach for achieving consensus on subjects where none currently exists. Conclusion: Performing prospective clinical studies in this area is currently the best and only option to overcome this challenge. In the long term, this approach will not only incorporate the standard of clinical evidence but also adopt regional mores for treating infection, which include patient values, cultural differences and local financial resources.

Design and Evaluation of a New Type of Knee Orthosis to Align the Mediolateral Angle of the Knee Joint with Osteoarthritis

Directory of Open Access Journals (Sweden)

Amir Esrafilian

2012-01-01

Full Text Available Background. Osteoarthritis (OA is a disease which influences the performance of the knee joint. Moreover, the force and moments applied on the joint increase in contrast to normal subjects. Various types of knee orthoses have been designed to solve the mentioned problems. However, there are other problems in terms of distal migration during walking and the alignment of the orthosis which cannot be changed following the use of brace. Therefore, the main aim of the research was to design an orthosis to solve the aforementioned problems. Method. A new type of knee orthosis was designed with a modular structure. Two patients with knee OA participated in this research project. The force applied on the foot, moment transmitted through the knee joint, and spatiotemporal gait parameters were measured by use of a motion analysis system. Results. The results of the research showed that the adduction moment applied on the knee joint decreased while subjects walked with the new knee orthosis (P-value < 0.05. Conclusion. The new design of the knee brace can be used as an effective treatment to decrease the loads applied on the knee joint and to improve the alignment whilst walking.

MRI of the internal derangement of temporomandibular joint: Comparison with arthrographic and operation

International Nuclear Information System (INIS)

Kim, Mi Hye; Kim, Dong Ik; Kim, Hyung Gon; Suh, Jung Ho; Jung, Tae Sub

1993-01-01

We retrospectively reviewed the MRI findings of 100 temporomandibular joints in 78 patients who had complained temporomandibular joint dysfunction. MRI findings were classified according to Wilke's staging criteria. And these findings were compared with arthographic findings in 22 joint and surgical findings in 44 joints. According to Wilke's staging, they were classified into 6 stages of abnormality: stage 0 (33 cases), stage I (19 cases), stage II (10 cases), stage III (18 cases), stage IV (6 cases), stage V (14 cases). Among the 22 cases in which arthography and MRI were done, both studies were well correlated in 10 joints. In 7 joints, MRI was superior to arthography, which correctly demonstrated the meniscal displacement in 2 joints and meniscal deformity in 5 joints. In 5 joints, arthography was superior to MR, which demonstrated the perforation (1 joint), adhesion (2 joints) and recapture of meniscus (2 joints). Compared with surgical findings, MRI correctly demonstrated the displacement of meniscus in all 44 joints. However, in case of the 10 meniscal perforation, MRI demonstrated the meniscal discontinuity in only 4 joints. Retrospective MR findings in 10 proven cases were the defect in posterior attachment in 4, far anterior meniscal displacement without recapture in 8, condylar spur in 4, and close bone to bone contact in 1. In conclusion, MRI as a primary diagnostic modality of temporomandibular joint derangement, is superior for the grading of displacement and deformity of meniscus but inferior for the evaluation of perforation, adhesion and recapture of meniscus to conventional arthrography. In case of the suspected meniscal perforation, arthrographic correlation is recommended preoperatively

Analysis of stress- strain distribution of dowel and glue line in L-type furniture joint by means of finite element method

Directory of Open Access Journals (Sweden)

mossayeb dalvand

2017-08-01

Full Text Available In this study 3D stress-strain distribution of dowel and glue line on L-type joints made of plywood doweled was investigated. Members of joints made of 11-ply hardwood plywood (Hornbeam, Beech and Alder that were 19 mm in thickness. In this study effect of beech dowels in three levels diameters (6, 8 and 10 mm and penetration of depth (9, 13 and 17 mm on bending moment capacity of L-type joints under compression loading was investigated as experimental test, then stress-strain distribution of wood dowel and glue line in specimens were simulated by means of ANSYS 15 software with finite element method (FEM.Results have shown that bending moment resistance increased with increasing dowel diameter from 6 to 8 mm, but downward trend was observed with increasing 8 to 10 mm in dowel diameter. Bending moment resistance increased with increasing penetration depth. Also, result obtained of simulation by means of ANSYS software have shown that stress-strain in dowel and glue line increased with increasing diameter of dowel and Increasing stress in joints made of diameter dowel 10 mm due to fracture in joints and decrease in resistance once. According to results obtained of model analysis, the ultimate stress of dowel and glue line occurred in the area that joints were contacted.

MR image findings on advanced internal derangement of the temporomandibular joints. Cases of disc position changed from anterior disc displacement with reduction to without reduction

International Nuclear Information System (INIS)

Igarashi, Chinami; Kobayashi, Kaoru; Yuasa, Masao; Imanaka, Masahiro; Yamamoto, Akira

2005-01-01

This study was designed to evaluate the suggestion that the clinical findings and MR image findings of anterior disc displacement with reduction cases could not reduce the disc displacement within the follow-up period. We selected 26 joints without remarkable bone changes in the condylar head or glenoid fossa in which reduction disappeared during follow-up. Clinical evaluation focused on temporomandibular pain, trismus, and joint sound. MR imaging was targeted for configuration of articular disc, degree of disc displacement, and condylar head position. Clinical signs observed with progression of the condition were disappearance of joint sound in 12/26 joints (46.1%), temporomandibular pain in 15/26 joints (57.6%), and decreased distance of opening mouth in 19/26 joints (73%). MR image findings were disc configuration changes in 12/26 joints (46.1%), increased degree of anterior displacement of disc in 20/26 joints (76.9%), and condylar head position changes in 9/26 joints (34.6%). It is suggested that the advanced stage of internal derangement is closely associated with the degree of disc displacement. (author)

The influence of incline walking on joint mechanics.

Science.gov (United States)

Haggerty, Mason; Dickin, D Clark; Popp, Jennifer; Wang, Henry

2014-04-01

Walking is a popular form of exercise and is associated with many health benefits; however, frontal-plane knee joint loading brought about by a large internal knee-abduction moment and cyclic loading could lead to cartilage degeneration over time. Therefore, knee joint mechanics during an alternative walking exercise needs to be analyzed. The purpose of this study was to examine the lower-extremity joint mechanics in the frontal and sagittal planes during incline walking. Fifteen healthy males walked on a treadmill at five gradients (0%, 5%, 10%, 15%, and 20%) at 1.34m/s, and lower-extremity joint mechanics in the frontal and sagittal planes were quantified. The peak internal knee-abduction moment significantly decreased from the level walking condition at all gradients except 5%. Also, a negative relationship between the internal knee-abduction moment and the treadmill gradient was found to exist in 10% increments (0-10%, 5-15%, and 10-20%). The decrease in the internal knee-abduction moment during incline walking could have positive effects on knee joint health such as potentially reducing cartilage degeneration of the knee joint, reducing pain, and decreasing the rate of development of medial tibiofemoral osteoarthritis. This would be beneficial for a knee surgery patient, obese persons, and older adults who are using incline walking for rehabilitation and exercise protocols. Findings from the current study can provide guidance for the development of rehabilitation and exercise prescriptions incorporating incline walking. Copyright © 2014 Elsevier B.V. All rights reserved.

ECOWindS Joint Action Plan

DEFF Research Database (Denmark)

2014-01-01

The Joint Action Plan (JAP) is a deliverable of the ECOWindS project Work Package 4 (WP4) “Joint Action Plan”. It presents a plan of action or a roadmap for research, development, and innovation (RDI) for the Offshore Wind Service (OWS) industry. The objective of the JAP is to be an international...

Protection of welded joints against corrosion degradation

Directory of Open Access Journals (Sweden)

Jiří Votava

2013-01-01

Full Text Available Welded joints form an integral part of steel constructions. Welded joints are undetachable joints, which are however subjects of corrosion processes. The internal energy increases during the fusion welding especially in the heat affected places around the welded joint, which become initiating spot of corrosion degradation.The aim of the experiment is to put a welded joint produced by the MAG method to a test of corrosion degradation under the conditions of the norm ČSN ISO 9227 (salt-spray test. Organic and inorganic anticorrosion protections were applied on welded beads. First of all, there were prepared welded beads using the method MAG; secondly, metallographical analyses of welded metal, heat affected places and base material were processed. Further, microhardness as well as analysis of chemical composition using the EDS microscope were analysed. Based on a current trend in anticorrosion protections, there were chosen three types of protective coatings. First protective system was a double-layer synthetic system, where the base layer is formed by paint Pragroprimer S2000 and the upper layer by finishing paint Industrol S 2013. Second protective system is a duplex system formed by a combination of a base zinc coating with Zinorex paint. The last protective system was formed by zinc dipping only. Corrosion resistance of the individual tested samples was evaluated based on degradation of protective coating. The corrosion origin as well as the corrosion process were observed, the main criteria was the observation of welded bead.

Difficulty eating and significant weight loss in joint hypermobility syndrome/Ehlers-Danlos syndrome, hypermobility type.

Science.gov (United States)

Baeza-Velasco, Carolina; Van den Bossche, Thomas; Grossin, Daniel; Hamonet, Claude

2016-06-01

Joint Hypermobility Syndrome, also known as Ehlers-Danlos Syndrome Hypermobility Type (JHS/EDS-HT), is a heritable disorder of connective tissue, common but poorly known by the medical community. Although generalized joint hypermobility and fragility of tissues have been described as core features, recent research highlights the multisystemic nature of JHS/EDS-HT, which presents with a wide range of articular and extra-articular symptoms. Among these, gastrointestinal problems, temporomandibular disorders, and smell and taste abnormalities are common among those affected, having significant implications for eating. The present work reviews the literature linking JHS/EDS-HT and eating problems. Two illustrative case reports, in which JHS/EDS-HT manifestations contribute to developing and maintaining disturbed eating behaviors and significant weight loss, are presented.

Synovial deposition of wild-type transthyretin-derived amyloid in knee joint osteoarthritis patients.

Science.gov (United States)

Takanashi, Tetsuo; Matsuda, Masayuki; Yazaki, Masahide; Yamazaki, Hideshi; Nawata, Masashi; Katagiri, Yoshiki; Ikeda, Shu-Ichi

2013-09-01

To investigate histological features of deposited amyloid in the synovial tissue and its clinical significance in knee joint osteoarthritis (OA) patients. We prospectively enrolled 232 consecutive patients who underwent arthroplasty or total replacement of the knee joint for treatment of OA. Congo red staining and immunohistochemistry were performed in the synovial tissue obtained at surgery. When transthyretin (TTR)-derived amyloid was positive, we analyzed all 4 exons of the TTR gene using the direct DNA sequencing method in order to detect mutations. We analyzed 322 specimens in this study. Twenty-six specimens (8.1%) obtained from 21 patients (5 men and 16 women; mean, 79.0 ± 4.6 years) showed deposition of amyloid, which was positively stained with the anti-TTR antibody. Eighteen patients showed inhomogeneous accumulations of amyloid in the loose connective tissue under the synovial epithelia sometimes with nodule formation, while in the remaining three, small vessels in the adipose tissue were involved. Medical records of these patients revealed nothing remarkable in the clinical course, laboratory data or macroscopic intraarticular findings at surgery. No mutations were detectable in the TTR gene analysis. Wild-type TTR-derived amyloid may affect the synovial tissue as a result of long-term mechanical stress or as a part of senile systemic amyloidosis in approximately 8% of knee joint OA patients. No obvious clinical significance was found in synovial deposition of amyloid.

Damage mechanism of piping welded joints made from austenitic Steel for the type RBMK reactor

International Nuclear Information System (INIS)

Karzov, G.; Timofeev, B.; Gorbakony, A.; Petrov, V.; Chernaenko, T.

1999-01-01

In the process of operation of RBMK reactors the damages were taking place on welded piping, produced from austenitic stainless steel of the type 08X18H10T. The inspection of damaged sections in piping has shown that in most cases crack-like defects are of corrosion and mechanical character. The paper considers in details the reasons of damages appearance and their development for this type of welded joints of downcomers 325xl6 mm, which were fabricated from austenitic stainless steel using TlG and MAW welding methods. (author)

Agreement on the establishment of the ITER International Fusion Energy Organization for the Joint Implementation of the ITER Project. Latest status. Declarations/reservations

International Nuclear Information System (INIS)

2007-01-01

The Agreement on the Establishment of the ITER International Fusion Energy Organization for the Joint Implementation of the ITER Project, for which the Director General of the IAEA is depositary, was done in Paris on 21 November 2006. Pursuant to Article 22 thereof, the Agreement on the Establishment of the ITER International Fusion Energy Organization for the Joint Implementation of the ITER Project 'shall enter into force thirty days after the deposit of instruments of ratification, acceptance or approval of this Agreement by the People's Republic of China, EURATOM, the Republic of India, Japan, the Republic of Korea, the Russian Federation and the United States of America. The text of the Agreement is reproduced in the Annex hereto for the information of all Member States

Differential contributions of specimen types, culturing, and 16S rRNA sequencing in diagnosis of prosthetic joint infections

DEFF Research Database (Denmark)

Larsen, Lone Heimann; Khalid, Vesal; Xu, Yijuan

2018-01-01

Prosthetic joint failure is mainly caused by infection, aseptic failure (AF), and mechanical problems. Infection detection has been improved with modified culture methods and molecular diagnostics. However, comparisons between modified and conventional microbiology methods are difficult due...... to variations in specimen sampling. In this prospective, multidisciplinary study of hip or knee prosthetic failures, we assessed the contributions of different specimen types, extended culture incubations, and 16S rRNA sequencing for diagnosing prosthetic joint infections (PJI). Project specimens included joint...... fluid (JF), bone biopsy specimens (BB), soft-tissue biopsy specimens (STB), and swabs (SW) from the prosthesis, collected in situ, and sonication fluid collected from prosthetic components (PC). Specimens were cultured for 6 (conventional) or 14 days, and 16S rRNA sequencing was performed at study...

Influence of the implant-abutment connection design and diameter on the screw joint stability

Science.gov (United States)

Shin, Hyon-Mo; Huh, Jung-Bo; Yun, Mi-Jeong; Jeon, Young-Chan; Chang, Brian Myung

2014-01-01

PURPOSE This study was conducted to evaluate the influence of the implant-abutment connection design and diameter on the screw joint stability. MATERIALS AND METHODS Regular and wide-diameter implant systems with three different joint connection designs: an external butt joint, a one-stage internal cone, and a two-stage internal cone were divided into seven groups (n=5, in each group). The initial removal torque values of the abutment screw were measured with a digital torque gauge. The postload removal torque values were measured after 100,000 cycles of a 150 N and a 10 Hz cyclic load had been applied. Subsequently, the rates of the initial and postload removal torque losses were calculated to evaluate the effect of the joint connection design and diameter on the screw joint stability. Each group was compared using Kruskal-Wallis test and Mann-Whitney U test as post-hoc test (α=0.05). RESULTS The postload removal torque value was high in the following order with regard to magnitude: two-stage internal cone, one-stage internal cone, and external butt joint systems. In the regular-diameter group, the external butt joint and one-stage internal cone systems showed lower postload removal torque loss rates than the two-stage internal cone system. In the wide-diameter group, the external butt joint system showed a lower loss rate than the one-stage internal cone and two-stage internal cone systems. In the two-stage internal cone system, the wide-diameter group showed a significantly lower loss rate than the regular-diameter group (P<.05). CONCLUSION The results of this study showed that the external butt joint was more advantageous than the internal cone in terms of the postload removal torque loss. For the difference in the implant diameter, a wide diameter was more advantageous in terms of the torque loss rate. PMID:24843398

Influence of the implant-abutment connection design and diameter on the screw joint stability.

Science.gov (United States)

Shin, Hyon-Mo; Huh, Jung-Bo; Yun, Mi-Jeong; Jeon, Young-Chan; Chang, Brian Myung; Jeong, Chang-Mo

2014-04-01

This study was conducted to evaluate the influence of the implant-abutment connection design and diameter on the screw joint stability. Regular and wide-diameter implant systems with three different joint connection designs: an external butt joint, a one-stage internal cone, and a two-stage internal cone were divided into seven groups (n=5, in each group). The initial removal torque values of the abutment screw were measured with a digital torque gauge. The postload removal torque values were measured after 100,000 cycles of a 150 N and a 10 Hz cyclic load had been applied. Subsequently, the rates of the initial and postload removal torque losses were calculated to evaluate the effect of the joint connection design and diameter on the screw joint stability. Each group was compared using Kruskal-Wallis test and Mann-Whitney U test as post-hoc test (α=0.05). THE POSTLOAD REMOVAL TORQUE VALUE WAS HIGH IN THE FOLLOWING ORDER WITH REGARD TO MAGNITUDE: two-stage internal cone, one-stage internal cone, and external butt joint systems. In the regular-diameter group, the external butt joint and one-stage internal cone systems showed lower postload removal torque loss rates than the two-stage internal cone system. In the wide-diameter group, the external butt joint system showed a lower loss rate than the one-stage internal cone and two-stage internal cone systems. In the two-stage internal cone system, the wide-diameter group showed a significantly lower loss rate than the regular-diameter group (P<.05). The results of this study showed that the external butt joint was more advantageous than the internal cone in terms of the postload removal torque loss. For the difference in the implant diameter, a wide diameter was more advantageous in terms of the torque loss rate.

A Study on Fatigue Design Automation of Plug- and Ring-type Gas-welded Joints of STS301L Taking Welded Residual Stress into Account

International Nuclear Information System (INIS)

Baek, Seung yeb; Yun, Ki Ho

2010-01-01

This paper presents a fatigue design method for plug- and ring-type gas-welded joints, which takes into account the effects of welding residual stress. To develop this method, we simulated the gas-welding process by performing nonlinear finite element analysis (FEA) To validate the FEA results, numerically calculated residual stresses in the gas welds were then compared with experimental results obtained by the hole-drilling method. To evaluate the fatigue strength of plug- and ring-type gas-welded joints influenced by welding residual stresses, the use of stress amplitude (σ a )R, which includes the welding residual stress in gas welds, is proposed (σ a )R on the basis of a modified Goodman equation that includes the residual stress effects. Using the stress amplitude (σ a )R at the hot spot point of gas weld, the relations obtained as the fatigue test results for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged to obtain the (σ a )R-N f relationship. It was found that more systematic and accurate evaluation of the fatigue strength of plug- and ring-type gas-welded joints can be achieved by using (σ a )R

Development of radiographic technique for examining k-type butt weld

International Nuclear Information System (INIS)

Barui, K.L.; Bhattacharyya, B.

1983-01-01

An attempt is made to develop a radiographic technique for examining K-type full penetration butt joints in heavy duty crane girders. The existing standard techniques of radiographic examination is found to be unsuitable to assess the internal defects properly. The examination technique reported here is successful in detecting not only the nature of the internal defects but also their degree of severities - from which clues for avoiding the most probable defects can be found out. The results of radiographic examination applied on the K-type butt joints of heavy duty crane girders have been discussed and it is specified that the acceptable limit of the defects must lie between 'blue' and 'green' according to the IIW colour code. Much work is yet to be done before standard specifications regarding the acceptibility of the defects in the actual job can be formulated. (author)

Root Cause Investigation of the Starboard Solar Alpha Rotary Joint Anomaly on the International Space Station

Science.gov (United States)

Taylor, Deneen; Enriquez, Carlos; McCann, David; McFatter, Justin

2010-01-01

The Solar Alpha Rotary Joint (SARJ) is a single-axis pointing mechanism used to orient the solar power generating arrays relative to the sun for the International Space Station (ISS). Approximately 83 days after its on-orbit installation, one of the two SARJ mechanisms aboard the ISS began to exhibit high current draw. Later inspections via Extravehicular Activity (EVA) discovered that the case hardened steel race ring on the outboard side of the joint had extensive damage to one of its three rolling surfaces. A far-reaching investigation of the anomaly was undertaken, comprising metallurgical inspections, coupon tests, traction kinematics tests, detailed bearing measurements, and thermal and structural analyses. The investigation found that the race ring damage had been caused by high bearing edge stresses that resulted from inadequate lubrication of the rolling contact. The profile of the roller bearings and the metallurgical properties of the race ring were also found to be significant contributing factors.

Text of the agreement between the International Atomic Energy Agency and the United Nations Educational, Scientific and Cultural Organization concerning the joint operation of the International Centre for Theoretical Physics at Trieste

International Nuclear Information System (INIS)

1996-02-01

The text of the Agreement between the International Atomic Energy Agency and the United Nations Educational, Scientific and Cultural Organization concerning the Joint Operation of the International Centre for Theoretical Physics at Trieste is reproduced in this document for the information of all Members. The Agreement was approved by the Agency's Board of Governors on 25 February 1993 and by the UNESCO General Conference on 16 November 1993

Large expansion joint movement test; Teste de movimentacao de juntas de expansao de grande porte

Energy Technology Data Exchange (ETDEWEB)

Medeiros, Jorivaldo; Veiga, Jordana Luiza Barbosa da Costa [PETROBRAS, Rio de Janeiro, RJ (Brazil); Veiga, Jose Carlos [Teadit, Rio de Janeiro, RJ (Brazil)

2008-07-01

This paper show the results obtained in a movement test realized on metallic bellows expansion joints used in the turbo expander duct system. A test device was developed. For dada acquisition a dynamometer was used and the tests were performed on gimbal expansion joints type. The joints were pressurized with water during the test. Data acquisition was realized at the design, operation and room pressure. The expansion joints were tested rotating them to the design angular movement of 3 deg and 6 deg degrees. The reactions for each degree of movement were recorded during loading and unloading. The tests confirmed that the expansion joints presented no-interference from construction, which configure in an adequate acceptance proceeding. It was noted the influence of internal pressure on reaction forces during expansion joints movements, these forces are not taken into consideration on theoretical calculations of EJMA design equations. The influence of friction on expansion joints hinges are significant and shall be considered on piping design and mitigated using friction reduction devices. (author)

[Case-control study on minimally invasive percutaneous locking compression plate internal fixation for the treatment of type II and III pilon fractures].

Science.gov (United States)

Zhang, Zhi-Da; Ye, Xiu-Yi; Shang, Li-Yong; Xu, Rong-Ming; Zhu, Yan-Zhao

2011-12-01

To explore the clinical efficacy of delayed open reduction and internal fixation with minimally invasive percutaneous locking compression plate for the treatment of type II and III Pilon fractures. From January 2007 to September 2009, 32 patients with type II and III Pilon fractures were treated with open reduction and anatomic plate fixation (AP group) and minimally invasive percutaneous locking compression plate osteosynthesis (LCP group). There were 11 males and 6 females in AP group, with an average age of (37.4 +/- 13.3) years (ranged, 19 to 55 years). And there were 10 males and 5 females in LCP group, with an average age of (34.6 +/- 11.3) years(ranged, 21 to 56 years). The operating time, fracture healing time, aligned angulation and ankle function were compared between the two groups. All the patients were followed up, and the during ranged from 12 to 25 months, with a mean of (15.0 +/- 1.7) months. The average operation time was (76.5 +/- 8.3) min for AP group and (58.3 +/- 3.4) min for LCP group; the average time of fracture healing was (20.5 +/- 0.4) weeks for AP group and (15.7 +/- 0.2) weeks for LCP group; the total angulation between anterior posterior film and lateral film was averaged (6.6 +/- 0.5) degrees for AP group and (3.6 +/- 0.2) degrees for LCP group. As to above index, the results of LCP group were better than those of AP group (P ankle joint, the results of LCP group were better than those of AP group in ankle joint pain, wakling and ankle joint function (P fracture with less invasion, faster bone union, more stabilized fixation, quicker recovery of ankle function and fewer complications, which is more advantaged for type II and III Pilon fractures.

Differential diagnosis and diagnostic flow chart of joint hypermobility syndrome/ehlers-danlos syndrome hypermobility type compared to other heritable connective tissue disorders.

Science.gov (United States)

Colombi, Marina; Dordoni, Chiara; Chiarelli, Nicola; Ritelli, Marco

2015-03-01

Joint hypermobility syndrome/Ehlers-Danlos syndrome hypermobility type (JHS/EDS-HT) is an evolving and protean disorder mostly recognized by generalized joint hypermobility and without a defined molecular basis. JHS/EDS-HT also presents with other connective tissue features affecting a variety of structures and organs, such as skin, eye, bone, and internal organs. However, most of these signs are present in variable combinations and severity in many other heritable connective tissue disorders. Accordingly, JHS/EDS-HT is an "exclusion" diagnosis which needs the absence of any consistent feature indicative of other partially overlapping connective tissue disorders. While both Villefranche and Brighton criteria include such an exclusion as a mandatory item, a systematic approach for reaching a stringent clinical diagnosis of JHS/EDS-HT is still lacking. The absence of a consensus on the diagnostic approach to JHS/EDS-HT concerning its clinical boundaries with similar conditions contribute to limit our actual understanding of the pathologic and molecular bases of this disorder. In this review, we revise the differential diagnosis of JHS/EDS-HT with those heritable connective tissue disorders which show a significant overlap with the former and mostly include EDS classic, vascular and kyphoscoliotic types, osteogenesis imperfecta, Marfan syndrome, Loeys-Dietz syndrome, arterial tortuosity syndrome, and lateral meningocele syndrome. A diagnostic flow chart is also offered with the attempt to support the less experienced clinician in stringently recognizing JHS/EDS-HT and stimulate the debate in the scientific community for both management and research purposes. © 2015 Wiley Periodicals, Inc.

International fusion research

International Nuclear Information System (INIS)

Pease, R.S.

1983-01-01

Nuclear energy of the light elements deuterium and lithium can be released if the 100 MK degree temperature required for deuterium-tritium thermonuclear fusion reactions can be achieved together with sufficient thermal insulation for a net energy yield. Progress of world-wide research shows good prospect for these physical conditions being achieved by the use of magnetic field confinement and of rapidly developing heating methods. Tokamak systems, alternative magnetic systems and inertial confinement progress are described. International co-operation features a number of bilateral agreements between countries: the Euratom collaboration which includes the Joint European Torus, a joint undertaking of eleven Western European nations of Euratom, established to build and operate a major confinement experiment; the development of co-operative projects within the OECD/IEA framework; the INTOR workshop, a world-wide study under IAEA auspices of the next major step in fusion research which might be built co-operatively; and assessments of the potential of nuclear fusion by the IAEA and the International Fusion Research Council. The INTOR (International Tokamak Reactor) studies have outlined a major plant of the tokamak type to study the engineering and technology of fusion reactor systems, which might be constructed on a world-wide basis to tackle and share the investment risks of the developments which lie ahead. This paper summarizes the recent progress of research on controlled nuclear fusion, featuring those areas where international co-operation has played an important part, and describes the various arrangements by which this international co-operation is facilitated. (author)

Surgical treatment for diffused-type giant cell tumor (pigmented villonodular synovitis) about the ankle joint.

Science.gov (United States)

Li, Xingchen; Xu, Yang; Zhu, Yuan; Xu, Xiangyang

2017-11-14

Diffused-type giant cell tumor(Dt-GCT) is a rare, aggressive disorder of the joint synovium, bursa and tendon sheaths. Osseous erosions and subchondral cysts may develop as the result of synovium infiltration in Dt-GCT. We present a retrospective study of a series of patients who are diagnosed with Dt-GCT about the ankle joint, there clinical outcome is evaluated in this study. Fifteen patients with radiologically and histologically confirmed Dt-GCT about the ankle joint were identified in our foot and ankle department. Patients were managed with open synovectomy for the tumor tissue and bone grafting for bony erosions. X-rays and MRI scans were used for evaluation of the tumor and bony erosions pre- and post-operatively. Pre- and post-operative ankle function was assessed using the American Orthopedic Foot and Ankle Society -Ankle and Hindfoot (AOFAS-AH) score and the Muscularskeletal Tumor Society (MSTS) score. The mean follow-up duration was 37.4 months (range 25 to 50 months). There were 6 males and 9 females, with a mean age of 35 years old (range 18 to 65 years). All patients had talar erosion with the average size of 10.1*9.1*8.2 mm, distal tibia was affected in 5 patients with the average size of 6.2*5.6*5.8 mm. 7 patients had tendon involvement, 2 patients had recurrence and progression of ankle osteoarthritis. Both of them underwent ankle fusion. At the time of last follow-up, the mean AOFAS-AH score increased from 49 to 80 points (p ankle joint. Fusion is recommended for failed and severe cartilage destruction of the ankle joint.

The prevalence of erosive osseous changes of the articular eminence in the temporomandibular joint in patients with mandibular prognathism without internal derangement. MR and helical CT findings

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Takafumi; Ito, Jusuke; Tanaka, Rei; Koyama, Jun-ichi; Kobayashi, Fukiko [Niigata Univ. (Japan). Graduate School of Medical and Dental Sciences

2002-06-01

The aim of this study was to assess the prevalence of erosive osseous changes of the articular eminence in the temporomandibular joint without internal derangement. Sixty joints of 30 consecutive patients with mandibular prognathism were evaluated with both MR imaging and helical CT. On MPR images obtained with helical CT, erosive osseous changes of the articular eminence were observed in 18 joints (30%) of 13 patients. None of the joints studied demonstrated an osseous change in the mandibular condyle. MR imaging failed to detect erosive osseous changes of the articular eminence in all of the joints studied. In conclusion, MPR images obtained with helical CT were of value to detect erosive osseous changes of the articular eminence. (author)

The prevalence of erosive osseous changes of the articular eminence in the temporomandibular joint in patients with mandibular prognathism without internal derangement. MR and helical CT findings

International Nuclear Information System (INIS)

Hayashi, Takafumi; Ito, Jusuke; Tanaka, Rei; Koyama, Jun-ichi; Kobayashi, Fukiko

2002-01-01

The aim of this study was to assess the prevalence of erosive osseous changes of the articular eminence in the temporomandibular joint without internal derangement. Sixty joints of 30 consecutive patients with mandibular prognathism were evaluated with both MR imaging and helical CT. On MPR images obtained with helical CT, erosive osseous changes of the articular eminence were observed in 18 joints (30%) of 13 patients. None of the joints studied demonstrated an osseous change in the mandibular condyle. MR imaging failed to detect erosive osseous changes of the articular eminence in all of the joints studied. In conclusion, MPR images obtained with helical CT were of value to detect erosive osseous changes of the articular eminence. (author)

Management of acromioclavicular joint injuries.

Science.gov (United States)

Li, Xinning; Ma, Richard; Bedi, Asheesh; Dines, David M; Altchek, David W; Dines, Joshua S

2014-01-01

Acromioclavicular joint injuries are among the most common shoulder girdle injuries in athletes and most commonly result from a direct force to the acromion with the arm in an adducted position. Acromioclavicular joint injuries often present with associated injuries to the glenohumeral joint, including an increased incidence of superior labrum anterior posterior (SLAP) tears that may warrant further evaluation and treatment. Anteroposterior stability of the acromioclavicular joint is conferred by the capsule and acromioclavicular ligaments, of which the posterior and superior ligaments are the strongest. Superior-inferior stability is maintained by the coracoclavicular (conoid and trapezoid) ligaments. Type-I or type-II acromioclavicular joint injuries have been treated with sling immobilization, early shoulder motion, and physical therapy, with favorable outcomes. Return to activity can occur when normal shoulder motion and strength are obtained and the shoulder is asymptomatic as compared with the contralateral normal extremity. The management of type-III injuries remains controversial and is individualized. While a return to the previous level of functional activity with nonsurgical treatment has been documented in a number of case series, surgical reduction and coracoclavicular ligament reconstruction has been associated with a favorable outcome and can be considered in patients who place high functional demands on their shoulders or in athletes who participate in overhead sports. Surgical management is indicated for high-grade (≥type IV) acromioclavicular joint injuries to achieve anatomic reduction of the acromioclavicular joint, reconstruction of the coracoclavicular ligaments, and repair of the deltotrapezial fascia. Outcomes after surgical reconstruction of the coracoclavicular ligaments have been satisfactory with regard to achieving pain relief and return to functional activities, but further improvements in the biomechanical strength of these

Effect of welding processes and joint configuration on the residual stresses and distortion in type 316 LN stainless steel weld joints

International Nuclear Information System (INIS)

Vasantharaja, P.; Vasudevan, M.; Palanichamy, P.

2012-01-01

Fabrication by welding introduces significant residual stresses in the welded structure/component due to non-uniform heat distribution during heating and cooling cycle. To control, reduce, or beneficially redistribute the residual stresses in weld joints, the stress distribution needs to be known. In the present study, weld joints of 16 mm thick 316LN stainless steel were made by multi-pass TIG, A-TIG welding and combination of TIG and A-TIG welding processes with various joint configurations. While V-groove edge preparation was required for making multi-pass TIG weld joint, square-edge preparation was sufficient for making A-TIG weld joint. Ultrasonic nondestructive technique based on the critically refracted longitudinal waves (LCR waves) has been used for the quantitative surface/sub-surface residual stress measurements in the weld joints. Distortion measurements were carried out before and after welding using height gauge. A-TIG weld joint was found to exhibit significant reduction in tensile residual stresses and distortion in comparison to that of other joints. (author)

Determination of Parachute Joint Factors using Seam and Joint Testing

Science.gov (United States)

Mollmann, Catherine

2015-01-01

This paper details the methodology for determining the joint factor for all parachute components. This method has been successfully implemented on the Capsule Parachute Assembly System (CPAS) for the NASA Orion crew module for use in determining the margin of safety for each component under peak loads. Also discussed are concepts behind the joint factor and what drives the loss of material strength at joints. The joint factor is defined as a "loss in joint strength...relative to the basic material strength" that occurs when "textiles are connected to each other or to metals." During the CPAS engineering development phase, a conservative joint factor of 0.80 was assumed for each parachute component. In order to refine this factor and eliminate excess conservatism, a seam and joint testing program was implemented as part of the structural validation. This method split each of the parachute structural joints into discrete tensile tests designed to duplicate the loading of each joint. Breaking strength data collected from destructive pull testing was then used to calculate the joint factor in the form of an efficiency. Joint efficiency is the percentage of the base material strength that remains after degradation due to sewing or interaction with other components; it is used interchangeably with joint factor in this paper. Parachute materials vary in type-mainly cord, tape, webbing, and cloth -which require different test fixtures and joint sample construction methods. This paper defines guidelines for designing and testing samples based on materials and test goals. Using the test methodology and analysis approach detailed in this paper, the minimum joint factor for each parachute component can be formulated. The joint factors can then be used to calculate the design factor and margin of safety for that component, a critical part of the design verification process.

[Internal fixation with one-hole microplate for the treatment of collateral ligament injuries of the metacarpophalangeal joint of the thumb combined with fracture].

Science.gov (United States)

Wang, Xi-Xun; Sun, De-Tao; Chen, Xu-Hui; Li, Jun; Cui, Yan; Hu, Ji-Chao; Shu, Zheng-Hua; He, Jian; Ding, Chao-Qi; Chen, Bo

2015-03-01

To study clinical effects of one-hole microplate internal fixation for the treatment of collateral ligament injuries of the metacarpophalangeal joint of the thumb combined with fracture. Twenty-two patients (16 males, 6 females) with collateral ligament injuries of the metacarpophalangeal joint of the thumb combined fracture were treated with one-hole microplate internal fixation. The age of the patients ranged from 18 to 53 years old with a mean age of 28.5 years old. The duration from injury to surgery ranged from 2 hours to 2 months, and the mean time was 6 days. All the patients had collateral ligament injuries combined with fracture of the metacarpophalangeal joint of the thumb. Thirteen patients had injuries in the right hand and 9 patients had injuries in the left hand. There were 18 cases of closed wound and 4 cases of open wound. Eighteen patients had fresh injuries ( 2 weeks). Sixteen patients had injuries in the ulnar collateral ligament of the thumb combined with fracture, 6 patients had radial collateral ligament injuries of the thumb combined with fracture, 4 cases of which were complicated with injuries of abductor pollicis brevis and the end of the flexor pollicis brevis tender. The size of the avulsed fragment was about 3.0 mm x 4.0 mm to 6.0 mm x 7.0 mm. The incisions of 22 patients healed by first intention. The follow-up periods ranged from 6 months to 5 years old,with an average of 2.5 years old. The thumb function was evaluated by Saetta and other evaluation criteria, and 20 patients got an excellent result and 2 good. The application of one-hole microplate internal fixation in treating collateral ligament injuries with fracture of the metacarpophalangeal joint of the thumb is an effective method.

Surgical treatment of a concurrent type 5 acromioclavicular joint dislocation and a failed anterior glenohumeral joint stabilization

OpenAIRE

Rashid, Abbas; Lawrence, Christopher; Tytherleigh-Strong, Graham

2016-01-01

Traumatic glenohumeral joint dislocation and acromioclavicular joint subluxations tend to occur in young active males. Use of the coracoid process either as a transfer in recurrent instability or in suspensory reconstructions of the coracoclavicular ligaments have gained popularity. However this requires careful consideration in the event of concomitant injuries if they both require surgery.

Machined and plastic copings in three-element prostheses with different types of implantabutment joints: a strain gauge comparative analysis

Directory of Open Access Journals (Sweden)

Renato Sussumu Nishioka

2010-06-01

Full Text Available OBJECTIVE: Using strain gauge (SG analysis, the aim of this in vitro study was quantify the strain development during the fixation of three-unit screw implant-supported fixed partial dentures, varying the types of implant-abutment joints and the type of prosthetic coping. The hypotheses were that the type of hexagonal connection would generate different microstrains and the type of copings would produce similar microstrains after prosthetic screws had been tightened onto microunit abutments. MATERIALS AND METHODS: Three dental implants with external (EH and internal (IH hexagonal configurations were inserted into two polyurethane blocks. Microunit abutments were screwed onto their respective implant groups, applying a torque of 20 Ncm. Machined Co-Cr copings (M and plastic prosthetic copings (P were screwed onto the abutments, which received standard wax patterns. The wax patterns were cast in Co-Cr alloy (n=5, forming four groups: G1 EH/M; G2 EH/P; G3 IH/M and G4 IH/P. Four SGs were bonded onto the surface of the block tangentially to the implants, SG 1 mesially to implant 1, SG 2 and SG 3 mesially and distally to implant 2, respectively, and SG 4 distally to implant 3. The superstructure's occlusal screws were tightened onto microunit abutments with 10 Ncm torque using a manual torque driver. The magnitude of microstrain on each SG was recorded in units of microstrain (µε. The data were analyzed statistically by ANOVA and Tukey's test (p0.05. The hypotheses were partially accepted. CONCLUSIONS: It was concluded that the type of hexagonal connection and coping presented similar mechanical behavior under tightening conditions.

Thermal Cycling Life Prediction of Sn-3.0Ag-0.5Cu Solder Joint Using Type-I Censored Data

Directory of Open Access Journals (Sweden)

Jinhua Mi

2014-01-01

Full Text Available Because solder joint interconnections are the weaknesses of microelectronic packaging, their reliability has great influence on the reliability of the entire packaging structure. Based on an accelerated life test the reliability assessment and life prediction of lead-free solder joints using Weibull distribution are investigated. The type-I interval censored lifetime data were collected from a thermal cycling test, which was implemented on microelectronic packaging with lead-free ball grid array (BGA and fine-pitch ball grid array (FBGA interconnection structures. The number of cycles to failure of lead-free solder joints is predicted by using a modified Engelmaier fatigue life model and a type-I censored data processing method. Then, the Pan model is employed to calculate the acceleration factor of this test. A comparison of life predictions between the proposed method and the ones calculated directly by Matlab and Minitab is conducted to demonstrate the practicability and effectiveness of the proposed method. At last, failure analysis and microstructure evolution of lead-free solders are carried out to provide useful guidance for the regular maintenance, replacement of substructure, and subsequent processing of electronic products.

Evaluation of Patient-Oriented Standards of Joint Commission International in Gilan and Mazandaran Teaching Hospitals

Directory of Open Access Journals (Sweden)

Ghaseminejhad

2016-08-01

Full Text Available Background Medical tourism, a multi-million-dollar industry, has had a significant effect in economic flourishing, creating jobs, and preventing the outflow of currency. Objectives The aim of this study was to evaluate teaching hospitals affiliated to Gilan and Mazandaran University of Medical Sciences, according to joint commission international (JCI standards. Methods This was a descriptive cross sectional study conducted among teaching hospitals affiliated to Gilan and Mazandaran University of Medical Sciences during year 2015. To collect data and evaluate the hospitals, patient-oriented standards of JCI was applied. Results Amongst the eight standards, international patient safety goals (IPSG (with a score of 87.5% had the highest, and patient and family education (PFE (with a score of 53.75% had the lowest score. Hospital “4” with a score of 90.41%, had the highest, and hospital “7” with 58.90%, had the lowest rate of compliance to the standards. According to the Mann-Whitney test, the observed statistics considering a P value of ≤ 0.05 level, was not significant, therefore on a 95% certainty level, there was no significant difference between hospitals in Gilan and Mazandaran, regarding compliance with standards. Overall, the hospitals under study were relatively prepared for attracting medical tourists. Conclusions According to the results, it seems that more planning and implementation of projects is required to strengthen the axes of the joint commission regarding accreditation of hospitals and attraction of medical tourists to these centers, especially foreign tourists. Researchers are recommended to pay special attention to the university of medical sciences of two provinces for the establishment of standards and utilization of professional consultants.

Surgical treatment of acute type V acromioclavicular joint dislocations in professional athletes: an anatomic ligament reconstruction with synthetic implant augmentation.

Science.gov (United States)

Triantafyllopoulos, Ioannis K; Lampropoulou-Adamidou, Kalliopi; Schizas, Nikitas P; Karadimas, Eleftherios V

2017-12-01

Most acromioclavicular (AC) joint injuries occur in men in their third decade of life during high-speed or high-impact body contact sports. The management of acute complete AC joint dislocation is surgical. Current surgical techniques include anatomic reconstruction of the main restraints of the AC joint and aim to improve functional outcomes and to reduce the complication rate. We present 10 cases of acute type V AC joint dislocation in professional athletes treated surgically with anatomic reconstruction of the coracoclavicular and AC ligaments and augmentation with the use of a synthetic polyester tape. The minimum follow-up of the patients was 2 years (mean, 48 months; range, 24-86 months). The postoperative functional outcome was assessed at 1 year and 2 years using the Constant-Murley, American Shoulder and Elbow Surgeons, and modified University of California-Los Angeles scoring systems. In all cases, the postoperative scores were significantly improved (P < .005 in all comparisons with the preoperative scores), and all patients returned to their preinjury high level of activity 6 months postoperatively. Radiographs at 1 month and 6 months revealed the maintenance of reduction. There were no complications. According to the results of our series of patients, demanding cases of acute AC joint dislocation Rockwood type V, in professional athletes, require anatomic fixation of both coracoclavicular and AC ligaments for return to sports as soon as possible and at the preinjury level of performance. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Metallic joints for very high vacuum

International Nuclear Information System (INIS)

Paigne, J.

1961-01-01

After defining three main types of joint; three types of distribution of the tightening force in the clamps are demonstrated; the distribution of stresses, distortion and displacements in these clamps is then calculated by means of the theory of elasticity. This is followed by experimental results on a particular means of tightening (i.e. screw-clamps). From a brief discussion on the behaviour of the clamps it is possible finally to define other types of joint deriving from the main types originally foreseen. (author) [fr

Experimental study of metal gasketed joints for ultra-high vacuums; Etude experimentale de joints metalliques pour ultra-vide

Energy Technology Data Exchange (ETDEWEB)

Boulloud, J. P.; Schweitzer, J. [Commissariat a l' energie atomique et aux energies alternatives - CEA, Service de Physique Appliquee, groupe de Vide, Centre d' Etudes Nucleaires de Saclay (France)

1960-07-01

Various type of leak-tight metal joints have been studied with their application in assemblies containing total vacuums in mind. Their integrity has been tested with a helium leak detector, and leaks of about 2 x 10{sup -12} cm{sup 3} Atm/s per meter of joint have been measured, simultaneously with the clamping effort applied at the joint and the deformation of the metal gasket. The integrity to clamping effort ratio curve is not retraced in reverse upon relaxation of the clamping effort, but a 'return curve' analogous to a hysteresis cycle explains why certain types of joint retain their integrity at high temperatures. The use of a tracer gas permits discrimination between external permeation of the joint and gas from occlusions between its mating surfaces. The authors have been led to consider that neither the nature nor the purity or surface condition of the joint have any basic influence on its integrity. Clamping effort values in respect of various joints and necessary for total integrity are indicated. Reprint of a paper published in Le vide, no. 82, Jul-Aug 1959 [French] L'etude de differents types de joints metalliques etanches, en vue de leur application a l'ultra-vide, a ete effectuee a l'aide d'un detecteur de fuite a helium. On a mesure simultanement le debit de fuite, l'effort applique sur le joint et sa deformation. On a reussi a mesurer des debits de fuite de l'ordre de 2 x 10{sup -12} cm{sup 3} Atm/s/m de joint pour l'air. La courbe de l'etancheite en fonction de l'effort applique n'est pas reversible et on a pu mettre en evidence un 'cycle d'hysteresis' qui explique que certains joints conservent leur etancheite a haute temperature. La methode de mesure d'etancheite au moyen d'un gaz traceur a amene a faire une distinction entre la permeation et le degazage des gaz occlus dans l'interface des joints et a considerer que ni la nature, ni la purete et ni l'etat de surface du joint n'ont une influence primordiale sur l'etancheite de joint. Des valeurs

Comparison of Internal Fixations for Distal Clavicular Fractures Based on Loading Tests and Finite Element Analyses

Directory of Open Access Journals (Sweden)

Rina Sakai

2014-01-01

Full Text Available It is difficult to apply strong and stable internal fixation to a fracture of the distal end of the clavicle because it is unstable, the distal clavicle fragment is small, and the fractured region is near the acromioclavicular joint. In this study, to identify a superior internal fixation method for unstable distal clavicular fracture, we compared three types of internal fixation (tension band wiring, scorpion, and LCP clavicle hook plate. Firstly, loading tests were performed, in which fixations were evaluated using bending stiffness and torsional stiffness as indices, followed by finite element analysis to evaluate fixability using the stress and strain as indices. The bending and torsional stiffness were significantly higher in the artificial clavicles fixed with the two types of plate than in that fixed by tension band wiring (P<0.05. No marked stress concentration on the clavicle was noted in the scorpion because the arm plate did not interfere with the acromioclavicular joint, suggesting that favorable shoulder joint function can be achieved. The stability of fixation with the LCP clavicle hook plate and the scorpion was similar, and plate fixations were stronger than fixation by tension band wiring.

Ball-and-socket ankle joint

International Nuclear Information System (INIS)

Pistoia, F.; Ozonoff, M.B.; Wintz, P.; Hartford Hospital, CT

1987-01-01

The ball-and-socket ankle joint is a malformation of the ankle in which the articular surface of the talus is hemispherical in both the anteroposterior and lateral projections and has a congruent, concave tibial articular surface. Fourteen patients with this condition were identified retrospectively. Thirteen patients were thought to have the congenital type of ball-and-socket ankle joint which in many was associated with tarsal coalition, short limb, and ray fusion and deletion anomalies. One case of the acquired type, demonstrating less geometric rounding of the talar margins, was seen in a patient with myelomeningocele, probably resulting from sensory and motor deficits. Although the exact etiology of the congenital type is unknown, its association with other malformations suggests that the ball-and-socket ankle joint results from an overall maldevelopment of the ankle and foot. (orig.)

International scientific seminar «Chronicle of Nature – a common database for scientific analysis and joint planning of scientific publications»

Directory of Open Access Journals (Sweden)

Juri P. Kurhinen

2016-05-01

Full Text Available Provides information about the results of the international scienti fic seminar «Сhronicle of Nature – a common database for scientific analysis and joint planning of scientific publications», held at Findland-Russian project «Linking environmental change to biodiversity change: large scale analysis оf Eurasia ecosystem».

Agreement on the privileges and immunities of the ITER International Fusion Energy Organization for the Joint Implementation of the ITER Project. Latest status. Declarations/reservations

International Nuclear Information System (INIS)

2007-01-01

The Agreement on the Privileges and Immunities of the ITER International Fusion Energy Organization for the Joint Implementation of the ITER Project, for which the Director General of the IAEA is depositary, was done in Paris on 21 November 2006. Pursuant to Article 25 thereof, the Agreement on the Privileges and Immunities of the ITER International Fusion Energy Organization for the Joint Implementation of the ITER Project 'shall enter into force thirty days after the deposit of instruments of ratification, acceptance or approval of this Agreement by the People's Republic of China, EURATOM, the Republic of India, Japan, the Republic of Korea and the Russian Federation.' The text of the Agreement is reproduced in the Annex hereto for the information of all Member States

TRANSFER OF MARKETING KNOWLEDGE IN THAI INTERNATIONAL JOINT VENTURE FIRMS

Directory of Open Access Journals (Sweden)

Osman Mohamad

2010-07-01

Full Text Available The focus of this study is the transfer of marketing knowledge within Thai joint venture firms. The perspectives of Thai managers were surveyed using a structured instrument. The analysis identifies seven dimensions of marketing management knowledge: promotion management, price management, logistics management, product innovation management, strategic marketing management, cross-cultural management, and target marketing management. The incidence of transfer is highest for activities in strategic marketing management, followed by price management. Transfer in product innovation management and target marketing management tends to vary with the age of the joint venture. Joint venture firms with foreign partners originating from Western, advanced, industrialised nations recorded the highest incidence of knowledge transfer occurring within product innovation management. This trend also holds true for the management of promotion activities. The incidence of transfer in target marketing management is lowest among firms with foreign partners from neighbouring nations. The incidence of knowledge transfer within product innovation and target marketing also tends to vary with the age of the joint venture. An analysis based on industry classification revealed that the transfer of knowledge regarding logistics management occurs most for firms in the manufacturing sector. In the service sector, the highest incidence of knowledge transfer within the areas of promotion management and target marketing management occurred in the agricultural sector.

Cooperation and conflict in international joint venture relationship

NARCIS (Netherlands)

Kemp, Ron

1999-01-01

This article reports the results of an empirical study focusing on the relationship between the relative dependence asymmetry of partners in a joint venture, the level and intensity of conflict between the partners, the level of trust and norms of exchange between the partners, and the performance

Are greenhouse gas emissions from international shipping a type of marine pollution?

International Nuclear Information System (INIS)

Shi, Yubing

2016-01-01

Whether greenhouse gas emissions from international shipping are a type of marine pollution is a controversial issue and is currently open to debate. This article examines the current treaty definitions of marine pollution, and applies them to greenhouse gas emissions from ships. Based on the legal analysis of treaty definitions and relevant international and national regulation on this issue, this article asserts that greenhouse gas emissions from international shipping are a type of ‘conditional’ marine pollution. - Highlights: • Greenhouse gas (GHG) emissions from international shipping are a type of ‘conditional’ marine pollution. • Shipping CO 2 may be treated as marine pollution under the 1972 London Dumping Convention. • Countries have adopted different legislation concerning the legal nature of GHG emissions from ships. • Regulating CO 2 emissions from ships as marine pollution may expedite global GHG emissions reduction.

Simulation Study on Multipassed Welding Distortion of Combined Joint Types using Thermo-Elastic-Plastic FEM

Directory of Open Access Journals (Sweden)

RN Lidam

2012-12-01

Full Text Available This paper investigates the angular distortion induced by the gas metal arc welding (GMAW process on the combined butt and T-joint with a thickness of 9 mm. The material used in this study was low manganese carbon steel S355J2G3. A 2-D and 3-D thermo-elastic-plastic finite element (FE analysis has been developed to simulate the induced distortion of multipassed welding. In this research, SYSWELD 2010 with its computation management tool, known as multipassed welding advisor (MPA, was applied to analyze the distortion behavior of combined joint types. To model the heat source of GMAW, Goldak's double ellipsoid representation, which is available within this finite element analysis (FEA code was selected. Prior to the results discussion, this paper also shows the step-bystep procedures to simulate combined jointing which begins with metallurgical and customized heat source modeling, and is followed by creating geometrical mesh using Visual-Mesh 6.5 for analyzing and processing the results. Apart from 2-D and 3-D comparison analysis, the final objective of this research is also aimed to be a baseline study to provide preliminary information in preparing the tools and equipment for experimental investigation.

Mixed models approaches for joint modeling of different types of responses.

Science.gov (United States)

Ivanova, Anna; Molenberghs, Geert; Verbeke, Geert

2016-01-01

In many biomedical studies, one jointly collects longitudinal continuous, binary, and survival outcomes, possibly with some observations missing. Random-effects models, sometimes called shared-parameter models or frailty models, received a lot of attention. In such models, the corresponding variance components can be employed to capture the association between the various sequences. In some cases, random effects are considered common to various sequences, perhaps up to a scaling factor; in others, there are different but correlated random effects. Even though a variety of data types has been considered in the literature, less attention has been devoted to ordinal data. For univariate longitudinal or hierarchical data, the proportional odds mixed model (POMM) is an instance of the generalized linear mixed model (GLMM; Breslow and Clayton, 1993). Ordinal data are conveniently replaced by a parsimonious set of dummies, which in the longitudinal setting leads to a repeated set of dummies. When ordinal longitudinal data are part of a joint model, the complexity increases further. This is the setting considered in this paper. We formulate a random-effects based model that, in addition, allows for overdispersion. Using two case studies, it is shown that the combination of random effects to capture association with further correction for overdispersion can improve the model's fit considerably and that the resulting models allow to answer research questions that could not be addressed otherwise. Parameters can be estimated in a fairly straightforward way, using the SAS procedure NLMIXED.

Prosthetic Joint Infections

Science.gov (United States)

Aslam, Saima; Darouiche, Rabih O.

2012-01-01

Prosthetic joint infections represent a major therapeutic challenge for both healthcare providers and patients. This paper reviews the predisposing factors, pathogenesis, microbiology, diagnosis, treatment and prophylaxis of prosthetic joint infection. The most optimal management strategy should be identified based on a number of considerations including type and duration of infection, antimicrobial susceptibility of the infecting pathogen, condition of infected tissues and bone stock, patient wishes and functional status. PMID:22847032

The Effect of Foot Progression Angle on Knee Joint Compression Force during Walking

DEFF Research Database (Denmark)

Baldvinsson, Henrik Koblauch; Heilskov-Hansen, Thomas; Alkjær, Tine

2013-01-01

males walked at a fixed speed of 4.5 km/h under three conditions: Normal walking, internally rotated and externally rotated. All gait-trials were recorded by six infrared cameras. Net joint moments were calculated by 3D inverse dynamics. The results revealed that the medial knee joint compartment......It is unclear how rotations of the lower limb affect the knee joint compression forces during walking. Increases in the frontal plane knee moment have been reported when walking with internally rotated feet and a decrease when walking with externally rotated feet. The aim of this study...... was to investigate the knee joint compressive forces during walking with internal, external and normal foot rotation and to determine if the frontal plane knee joint moment is an adequate surrogate for the compression forces in the medial and lateral knee joint compartments under such gait modifications. Ten healthy...

Are greenhouse gas emissions from international shipping a type of marine pollution?

Science.gov (United States)

Shi, Yubing

2016-12-15

Whether greenhouse gas emissions from international shipping are a type of marine pollution is a controversial issue and is currently open to debate. This article examines the current treaty definitions of marine pollution, and applies them to greenhouse gas emissions from ships. Based on the legal analysis of treaty definitions and relevant international and national regulation on this issue, this article asserts that greenhouse gas emissions from international shipping are a type of 'conditional' marine pollution. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analyzing Internal Fragmentation of Electrosprayed Ubiquitin Ions During Beam-Type Collisional Dissociation

Science.gov (United States)

Durbin, Kenneth R.; Skinner, Owen S.; Fellers, Ryan T.; Kelleher, Neil L.

2015-05-01

Gaseous fragmentation of intact proteins is multifaceted and can be unpredictable by current theories in the field. Contributing to the complexity is the multitude of precursor ion states and fragmentation channels. Terminal fragment ions can be re-fragmented, yielding product ions containing neither terminus, termed internal fragment ions. In an effort to better understand and capitalize upon this fragmentation process, we collisionally dissociated the high (13+), middle (10+), and low (7+) charge states of electrosprayed ubiquitin ions. Both terminal and internal fragmentation processes were quantified through step-wise increases of voltage potential in the collision cell. An isotope fitting algorithm matched observed product ions to theoretical terminal and internal fragment ions. At optimal energies for internal fragmentation of the 10+, nearly 200 internal fragments were observed; on average each of the 76 residues in ubiquitin was covered by 24.1 internal fragments. A pertinent finding was that formation of internal ions occurs at similar energy thresholds as terminal b- and y-ion types in beam-type activation. This large amount of internal fragmentation is frequently overlooked during top-down mass spectrometry. As such, we present several new approaches to visualize internal fragments through modified graphical fragment maps. With the presented advances of internal fragment ion accounting and visualization, the total percentage of matched fragment ions increased from approximately 40% to over 75% in a typical beam-type MS/MS spectrum. These sequence coverage improvements offer greater characterization potential for whole proteins with no needed experimental changes and could be of large benefit for future high-throughput intact protein analysis.

Paired organs--Should they be treated jointly or separately in internal dosimetry?

Energy Technology Data Exchange (ETDEWEB)

Parach, Ali-Asghar; Rajabi, Hossein; Askari, Mohammad-Ali [Department of Medical Physics, Faculty of Medical Sciences, Tarbiat Modares University, Tehran-Iran (Iran, Islamic Republic of)

2011-10-15

Purpose: Size, shape, and the position of paired organs are different in abdomen. However, the counterpart organs are conventionally treated jointly together in internal dosimetry. This study was performed to quantify the difference of specific absorbed fraction of organs in considering paired organs jointly like single organs or as two separate organs. Methods: Zubal phantom and GATE Monte Carlo package were used to calculate the SAF for the self-absorption and cross-irradiation of the lungs, kidneys, adrenal glands (paired organs), liver, spleen, stomach, and pancreas (single organs). The activity was assumed uniformly distributed in the organs, and simulation was performed for monoenergetic photons of 10, 50, 100, 500, 1000 keV and mono-energetic electrons of 350, 500, 690, 935, 1200 keV. Results: The results demonstrated that self-absorption of left and right counterpart organs may be different depending upon the differences in their masses. The cross-irradiations between left-to-right and right-to-left counterpart organs are always equal irrespective of difference in their masses. Cross-irradiation from the left and right counterpart organs to other organs are different (4-24 times in Zubal phantom) depending on the photon energy and organs. The irradiation from a single source organ to the left and right counterpart paired organs is always different irrespective of activity concentration. Conclusions: Left and right counterpart organs always receive different absorbed doses from target organs and deliver different absorbed doses to target organs. Therefore, in application of radiopharmaceuticals in which the dose to the organs plays a role, counterpart organs should be treated separately as two separate organs.

Paired organs--Should they be treated jointly or separately in internal dosimetry?

International Nuclear Information System (INIS)

Parach, Ali-Asghar; Rajabi, Hossein; Askari, Mohammad-Ali

2011-01-01

Purpose: Size, shape, and the position of paired organs are different in abdomen. However, the counterpart organs are conventionally treated jointly together in internal dosimetry. This study was performed to quantify the difference of specific absorbed fraction of organs in considering paired organs jointly like single organs or as two separate organs. Methods: Zubal phantom and GATE Monte Carlo package were used to calculate the SAF for the self-absorption and cross-irradiation of the lungs, kidneys, adrenal glands (paired organs), liver, spleen, stomach, and pancreas (single organs). The activity was assumed uniformly distributed in the organs, and simulation was performed for monoenergetic photons of 10, 50, 100, 500, 1000 keV and mono-energetic electrons of 350, 500, 690, 935, 1200 keV. Results: The results demonstrated that self-absorption of left and right counterpart organs may be different depending upon the differences in their masses. The cross-irradiations between left-to-right and right-to-left counterpart organs are always equal irrespective of difference in their masses. Cross-irradiation from the left and right counterpart organs to other organs are different (4-24 times in Zubal phantom) depending on the photon energy and organs. The irradiation from a single source organ to the left and right counterpart paired organs is always different irrespective of activity concentration. Conclusions: Left and right counterpart organs always receive different absorbed doses from target organs and deliver different absorbed doses to target organs. Therefore, in application of radiopharmaceuticals in which the dose to the organs plays a role, counterpart organs should be treated separately as two separate organs.

Treatment of Rockwood type III acromioclavicular joint dislocation using autogenous semitendinosus tendon graft and endobutton technique

Directory of Open Access Journals (Sweden)

Ye G

2016-01-01

Full Text Available Gang Ye, Chao-An Peng, Hua-Bin Sun, Jing Xiao, Kang Zhu Department of Orthopedics, the People’s Hospital of Huangpi District, Wuhan City, People’s Republic of China Background: The aim of this study was to evaluate the therapeutic effect of autogenous semitendinosus graft and endobutton technique, and compare with hook plate in treatment of Rockwood type III acromioclavicular (AC joint dislocation.Methods: From April 2012 to April 2013, we treated 46 patients with Rockwood type III AC joint dislocation. Patients were randomly divided into two groups: Group A was treated using a hook plate and Group B with autogenous semitendinosus graft and endobutton technique. All participants were followed up for 12 months. Radiographic examinations were performed every 2 months postoperatively, and clinical evaluation was performed using the Constant–Murley score at the last follow-up.Results: Results indicated that patients in Group B showed higher mean scores (90.3±5.4 than Group A (80.4±11.5 in terms of Constant–Murley score (P=0.001. Group B patients scored higher in terms of pain (P=0.002, activities (P=0.02, range of motion (P<0.001, and strength (P=0.004. In Group A, moderate pain was reported by 2 (8.7% and mild pain by 8 (34.8% patients. Mild pain was reported by 1 (4.3% patient in Group B. All patients in Group B maintained complete reduction, while 2 (8.7% patients in Group A experienced partial reduction loss. Two patients (8.7% encountered acromial osteolysis on latest radiographs, with moderate shoulder pain and limited range of motion.Conclusion: Autogenous semitendinosus graft and endobutton technique showed better results compared with the hook plate method and exhibited advantages of fewer complications such as permanent pain and acromial osteolysis. Keywords: Rockwood type III acromioclavicular joint dislocation, autogenous semitendinosus graft, endobutton, hook plate

Learning from Success & Failure: International Joint Ventures in Emerging Markets

DEFF Research Database (Denmark)

Nielsen, Ulrik B.

their expectations. Inter-partner learning has been proposed in the literature as a major cause of IJV instability. However, current research indicates that when IJV partners engage in joint learning to create new IJV-specific knowledge that benefits both partners it stabilizes and sustains the IJV. Yet, joint......, especially when the prime motive of the operation is to capture opportunities in the local markets. However, the performance of IJVs generally turns out to be quite poor whether measured in economic value added, parent organization’s satisfaction or survival. For instance, termination rates of IJVs...

Internal Flow Structures in Columnar Jointed Basalt from HREPPHÓLAR, Iceland

Science.gov (United States)

Mattsson, H. B.; Bosshard, S. A.; Hetenyi, G.; Almqvist, B.; Hirt, A. M.; Caricchi, L.; Caddick, M.

2010-12-01

Columnar jointed basalt from Hrepphólar in southern Iceland display spectacular internal structures when cut. These structures follow the overall orientation of the columns and display semi-circular to circular features when cross-cut. It was previously believed that these internal structures formed as a result of alteration due to circulation of meteoric water within the column-bounding fractures after emplacement. However, new field observations of viscous fingering within the columns and the fact that approximately 80% of the semi-circular features are found within the column whereas the remaining 20% are cut by the column-bounding fractures clearly shows that these internal structures must have formed prior to crack-propagation (and are thus primary features). Here we present the results of textural and petrological analyses through a cross-section of a column, in combination with magnetic susceptibility and anisotropy measurements of the same samples. The variation in textures and geochemistry can be attributed to the presence of diffuse banding caused by variations in the modal proportions of the main phenocryst phases (i.e., plagioclase, clinopyroxene, olivine and titanomagnetite/ilmenite). Orientation of plagioclase laths and titanomagnetite crystals (based on measurements in thin sections and AMS-measurements) are consistent with vertical flow alignment. Nowhere in the column can evidence for downwards flow be found (excluding the possibility of small-scale convection cells generating these features). It is proposed here, that the volume decrease associated with solidification (typically 10-15 vol.% for basaltic systems) and the increasing weight of the overlying crust results in upwelling of partially crystallized material into the centre of the columns. Preliminary numerical modeling indicates that the isotherms within individual columns become steeper with increasing depth in a lava flow (allowing for larger displacement distances). We propose that

Joint implementation, clean development mechanism and Tradable Permits. International regulation of greenhouse gases

Energy Technology Data Exchange (ETDEWEB)

Nielsen, L.; Rose Olsen, K.

2000-06-01

A 'correct' accreditation is a key issue when evaluating Joint Implementation as a global environmental instrument. Problems mentioned in the literature on Joint Implementation - including the problem of additionality - are often relating to the problem of defining a correct accreditation. This paper lists some of these problems and lists some of the tools available to solve the reported problems of accreditation. The paper concludes that the institutional framework is crucial in defining what a correct accreditation is. It also concludes that different groups may have different interests in Joint Implementation, and that each of the reported problems may be a problem to some of the Joint Implementation interests groups but not to others. In designing the institutional framework for JI it is important to know the incentives and motivations of the different groups. The main part of the paper is an analysis of the basic incentives and motivations of the different Joint Implementation interest groups. This analysis can be used to weight the problems of Joint Implementation from an environmental perspective and from the perspective of cost effectiveness. (au)

Joint implementation, clean development mechanism and Tradable Permits. International regulation of greenhouse gases

Energy Technology Data Exchange (ETDEWEB)

Nielsen, L; Rose Olsen, K

2000-06-01

A 'correct' accreditation is a key issue when evaluating Joint Implementation as a global environmental instrument. Problems mentioned in the literature on Joint Implementation - including the problem of additionality - are often relating to the problem of defining a correct accreditation. This paper lists some of these problems and lists some of the tools available to solve the reported problems of accreditation. The paper concludes that the institutional framework is crucial in defining what a correct accreditation is. It also concludes that different groups may have different interests in Joint Implementation, and that each of the reported problems may be a problem to some of the Joint Implementation interests groups but not to others. In designing the institutional framework for JI it is important to know the incentives and motivations of the different groups. The main part of the paper is an analysis of the basic incentives and motivations of the different Joint Implementation interest groups. This analysis can be used to weight the problems of Joint Implementation from an environmental perspective and from the perspective of cost effectiveness. (au)

Joint Performance and Planning System

Data.gov (United States)

US Agency for International Development — A joint State/USAID system hosted by State that integrates resource and performance information at the program level and enables more flexible and frequent entry of...

Introduction to the special issue on the 2011 Joint IEEE International Frequency Control Symposium and European Frequency and Time Forum.

Science.gov (United States)

Burt, Eric; Gill, Patrick

2012-03-01

The 8 invited and 17 contributed papers in this special issue focus on the following topical areas covered at the 2011 Joint IEEE International Frequency Control Symposium and European Frequency and Time Forum, held in San Francisco, California: 1) Materials and Resonators; 2) Oscillators, Synthesizers, and Noise; 3) Microwave Frequency Standards; 4) Sensors and Transducers; 5) Timekeeping and Time and Frequency Transfer; and 6) Optical Frequency Standards.

Changes in the internal structure of the human crystalline lens with diabetes mellitus type 1 and type 2

NARCIS (Netherlands)

Wiemer, N.G.M.; Dubbelman, M.; Hermans, E.A.; Ringens, P.J.; Polak, B.C.P.

2008-01-01

Purpose: To investigate the effect of diabetes mellitus (DM) type 1 and type 2 on the internal structure of the lens. Design: Observational cross-sectional study. Participants and Controls: One hundred seven patients with DM type 1, 106 patients with DM type 2, and 75 healthy control subjects.

Bridge joint fabrication and validation for SST-1 PF coil winding pack

International Nuclear Information System (INIS)

Prasad, Upendra; Sharma, A.N.; Patel, D.; Doshi, K.; Varmora, P.; Khristi, Y.; Pradhan, S.

2014-01-01

Highlights: • Prototype of bridge type joints fabricated and validated successfully. • Bridge type joints fabricated and validated on one of the SST-1 PF#3T coil successfully. • Joint resistance was measured with precision nano volt meter and PXI based data acquisition system. • Leak tightness of joint box was better than 3 × 10 −6 Pa m 3 s −1 . • The measured joint resistance of bridge type joint was ∼1.6 nano ohm. - Abstract: A novel concept of bridge joint for Poloidal field (PF) magnet of SST-1 with damaged winding pack has been realized. This joint has been fabricated on 5th and 6th layers of PF#3T coil winding pack (WP) after validation at 10 kA at liquid helium temperature of 4.2 K in current lead test chamber. The joint resistance of bridge joint was measured ∼1.6 nΩ at flat top DC current of 10 kA. This type of joint could be economically useful for revival of a shorted and damaged WP superconducting PF magnets of Tokamaks. In this paper, details of bridge joint design, fabrication and validations are discussed

A Review of Natural Joint Systems and Numerical Investigation of Bio-Inspired GFRP-to-Steel Joints

Directory of Open Access Journals (Sweden)

Evangelos I. Avgoulas

2016-07-01

Full Text Available There are a great variety of joint types used in nature which can inspire engineering joints. In order to design such biomimetic joints, it is at first important to understand how biological joints work. A comprehensive literature review, considering natural joints from a mechanical point of view, was undertaken. This was used to develop a taxonomy based on the different methods/functions that nature successfully uses to attach dissimilar tissues. One of the key methods that nature uses to join dissimilar materials is a transitional zone of stiffness at the insertion site. This method was used to propose bio-inspired solutions with a transitional zone of stiffness at the joint site for several glass fibre reinforced plastic (GFRP to steel adhesively bonded joint configurations. The transition zone was used to reduce the material stiffness mismatch of the joint parts. A numerical finite element model was used to identify the optimum variation in material stiffness that minimises potential failure of the joint. The best bio-inspired joints showed a 118% increase of joint strength compared to the standard joints.

Discrete and continuous joint coupling relationships in uninjured recreational runners.

Science.gov (United States)

Dierks, Tracy A; Davis, Irene

2007-06-01

Abnormal joint coupling is thought to be related to overuse injuries in runners. However, researchers do not yet know what constitutes normal joint coupling during running, which makes abnormal coupling difficult to define. Lower extremity kinematics were collected from 40 recreational runners during stance. Joint coupling methods were applied and, for each method, means and both within- and between-subject variability were calculated. The 95% confidence interval was used to compare differences across coupling relationships and periods of stance. Timing between rearfoot eversion, tibial internal rotation, and knee flexion were relatively synchronous while relationships involving knee internal rotation were more asynchronous. The excursion ratios showed that every 2 degrees of rearfoot eversion was coupled with 1 degrees of both tibial internal rotation and knee internal rotation. Vector coding results showed that just beyond maximum loading, all joint coupling relationships resulted in relatively equal amounts of motion, while the within-subject variability was similar throughout stance. The continuous relative phase results showed that the most out-of-phase coupling occurred in the periods around heel-strike and toe-off while the most in-phase coupling occurred in the period just beyond maximum loading of the leg. The continuous relative phase within-subject variability was greatest at the periods around heel-strike and toe-off and smallest just beyond maximum loading. With a better understanding of joint coupling in uninjured runners, these data will help to serve as a reference for future studies investigating the relationship between running injuries and abnormal joint coupling.

Sacroiliac joint tuberculosis: surgical management by posterior open-window focal debridement and joint fusion.

Science.gov (United States)

Zhu, Guo; Jiang, Li-Yuan; Yi, Zhang; Ping, Li; Duan, Chun-Yue; Yong, Cao; Liu, Jin-Yang; Hu, Jian-Zhong

2017-11-29

Sacroiliac joint tuberculosis(SJT) is relatively uncommon, but it may cause severe sacroiliac joint destruction and functional disorder. Few studies in the literature have been presented on SJT, reports of surgical treatment for SJT are even fewer. In this study, we retrospectively reviewed surgical management of patients with severe SJT of 3 different types and proposed to reveal the clinical manifestations and features and aim to determine the efficiency and security of such surgical treatment. We reviewed 17 patients with severe SJT of 3 different types who underwent posterior open-window focal debridement and bone graft for joint fusion. Among them,five patients with anterior sacral abscess had anterior abscess curettage before debridement. Two patients with lumbar vertebral tuberculosis received one-stage posterior tuberculous debridement, interbody fusion and instrumentation. Follow-up was performed 36 months (26 to 45 months) using the following parameters: erythrocyte sedimentation rate(ESR), status of joint bony fusion on CT scan, visual analogue scale (VAS) and the Oswestry Disability Index (ODI). Buttock pain and low back pain were progressively relieved with time. 6 months later, pain was not obvious, and ESR resumed to normal levels within 3 months. Solid fusion of the sacroiliac joint occurred within 12 months in all cases. No complications or recurrence occurred. At final follow-up, all patients had no pain or only minimal discomfort over the affected joint and almost complete functional recovery. Posterior open-window focal debridement and joint fusion is an efficient and secure surgical method to treat severe SJT. If there is an abscess in the front of the sacroiliac joint, anterior abscess curettage should be performed as a supplement.

Results and Analysis from Space Suit Joint Torque Testing

Science.gov (United States)

Matty, Jennifer

2010-01-01

This joint mobility KC lecture included information from two papers, "A Method for and Issues Associated with the Determination of Space Suit Joint Requirements" and "Results and Analysis from Space Suit Joint Torque Testing," as presented for the International Conference on Environmental Systems in 2009 and 2010, respectively. The first paper discusses historical joint torque testing methodologies and approaches that were tested in 2008 and 2009. The second paper discusses the testing that was completed in 2009 and 2010.

The joint choice of tenure, dwelling type, size and location: the effect of home-oriented versus culture-oriented lifestyle

DEFF Research Database (Denmark)

Frenkel, Amnon; Kaplan, Sigal

2014-01-01

This study investigates knowledge-workers’ housing preferences in terms of tenure, dwelling type, location and size. The analysis is conducted by applying a joint multinomial-logit ordered-response model to the housing choices of knowledgeworkers residing in the Tel-Aviv metropolitan region and w...

Traumatic injuries of the temporomandibular joint

International Nuclear Information System (INIS)

Puig, S.; Krestan, C.; Lomoschitz, F.; Robinson, S.; Glaser, C.; Staudenherz, A.

2001-01-01

Injuries of the temporomandibular joint are mostly due to injuries or fractures of the mandibular condyle. Fractures of the skull base involving the temporomandibular joint are rare. Classification of fractures refers to their anatomical positions and the presence or absence of a luxation. Further, it is important whether the fracture is intra- or extra-capsular. The primary imaging method should be orthopantomography. As for therapy planning, especially surgery, also evaluation of soft tissue is necessary, computed tomography is the imaging method of choice. For diagnosis of complications or internal derangement of the temporomandibular joint, magnetic resonance imaging is to be recommended. (orig.) [de

Quantification of disc displacement in internal derangement of the temporomandibular joint using magnetic resonance imaging.

Science.gov (United States)

Arayasantiparb, Raweewan; Tsuchimochi, Makoto

2010-02-01

Many measures have been developed to determine the extent of disc displacement in internal derangements of the temporomandibular joint (TMJ) using magnetic resonance imaging. The purpose of this study was to develop a quantitative method of analyzing disc position and to evaluate the positions of the disc in internal derangements of the TMJ (group 1, with reduction; group 2, without reduction). Magnetic resonance images of 150 TMJs in 20 healthy volunteers and 55 patients with internal derangements were evaluated. The anatomical points of interest of the TMJ, including the anterior (DA) and posterior (DP) points of the disc, were marked on parasagittal magnetic resonance images of the TMJ disc taken in both the closed- and the open-mouth positions. All points were recorded using an x-y coordinate system, with reference to a referral line. In the closed-mouth position, the DP in patients in group 1 was situated in a more-anterior direction than the DP in volunteers. The DP in group 2 was located further anterior and inferior than the DP in group 1. However, the position of the DA did not differ between group 1 and group 2. In the open-mouth position, the DP was displaced anteroinferiorly to a greater extent in group 2 than in group 1 (one-way ANOVA, followed by Scheffe's test; P displaced TMJ discs revealed no significant difference. In conclusion, most of our results quantitatively support previously reported findings in imaging, surgical, and histopathological studies of TMJ internal derangement. We suggest that our measure of disc position of the TMJ would be useful to assess the status and response to treatment of internal derangements of the TMJ.

Temporomandibular joint motion

International Nuclear Information System (INIS)

Maeda, M.; Kawamura, Y.; Matsuda, T.; Itou, S.; Odori, T.; Ishii, Y.; Torizuka, K.

1990-01-01

This paper evaluates MR imaging with the therapeutic effect after splint therapy in internal derangement of the temporomandibular joint (TMJ). Fifteen patients (19 TMJs) with internal derangement of the TMJ and five normal volunteers (10 TMJs) were examined with sagittal T1-weighted spin-echo and gradient recalled acquisition in a steady state (GRASS) MR imaging. MR studies of the patients undergoing splint therapy were performed with an without splints. Pseudodynamic images of TMJ motion provide information that was not available from spin-echo T1-weighted images

Joint contact loading in forefoot and rearfoot strike patterns during running.

Science.gov (United States)

Rooney, Brandon D; Derrick, Timothy R

2013-09-03

Research concerning forefoot strike pattern (FFS) versus rearfoot strike pattern (RFS) running has focused on the ground reaction force even though internal joint contact forces are a more direct measure of the loads responsible for injury. The main purpose of this study was to determine the internal loading of the joints for each strike pattern. A secondary purpose was to determine if converted FFS and RFS runners can adequately represent habitual runners with regards to the internal joint loading. Using inverse dynamics to calculate the net joint moments and reaction forces and optimization techniques to estimate muscle forces, we determined the axial compressive loading at the ankle, knee, and hip. Subjects consisted of 15 habitual FFS and 15 habitual RFS competitive runners. Each subject ran at a preferred running velocity with their habitual strike pattern and then converted to the opposite strike pattern. Plantar flexor muscle forces and net ankle joint moments were greater in the FFS running compared to the RFS running during the first half of the stance phase. The average contact forces during this period increased by 41.7% at the ankle and 14.4% at the knee joint during FFS running. Peak ankle joint contact force was 1.5 body weights greater during FFS running (pstrike pattern. Copyright © 2013 Elsevier Ltd. All rights reserved.

Joint radiation emergency management plan of the international organizations. Emergency preparedness and response. Date effective: 1 December 2004

International Nuclear Information System (INIS)

2004-11-01

directives and regulations that bear on emergency response arrangements among some States. The IAEA is the main co-ordinating body for development and maintenance of the Joint Plan. All States irrespective whether they are party to one or other of the two Conventions are invited to adopt arrangements that are compatible with those described here when providing relevant information about nuclear or radiological emergencies to relevant international organizations, in order to minimize the radiological consequences and to facilitate the prompt provision of information and assistance. This document is the third edition of the Joint Plan

The transitional vertebra and sacroiliac joint dysfunction association.

Science.gov (United States)

Illeez, Ozge Gulsum; Atıcı, Arzu; Ulger, Esra Bahadır; Kulcu, Duygu Geler; Ozkan, Feyza Unlu; Aktas, Ilknur

2018-01-01

The purpose of this study was to investigate whether transitional vertebrae contribute to the development of sacroiliac joint dysfunction. The prevalence of transitional vertebrae in patients with lumbar pain was determined during this process, and the prevalence of sacroiliac dysfunction was compared between patients with low back pain and healthy volunteers. 700 subjects, 500 with low back pain and 200 healthy volunteers were included in this study. Five tests were applied to all participants to determine sacroiliac joint dysfunction. Positivity in three tests was regarded as dysfunction. Lateral lumbosacral and Ferguson angle X-rays were taken from the group with low back pain. The patient was evaluated a specialist radiologist in terms of presence or absence of transitional vertebrae, and if identified, what type. Transitional vertebrae were determined in 26% (n = 130) of the patients with low back pain. Type 1a was determined in 20%, type 1b in 10%, type 2a in 26.9%, type 2b in 30.8%, type 3a in 0.8%, type 3b in 4.6% and type 4 in 6.9%. The prevalence of sacroiliac joint dysfunction in the low back pain group (15.4%) and the prevalence of sacroiliac joint dysfunction in cases of transitional vertebra (28.5%) were significantly higher compared to the control groups (p Sacroiliac joint dysfunction must be considered when investigating the etiology of low back pain. Particular sensitivity must be exhibited on this subject in patients with transitional vertebrae.

[Case control study on therapeutic effects of dynamic external fixtor combined with limited internal fixation and cross K-wires fixation for the treatment of Pilon fractures of the proximal interphalangeal joint].

Science.gov (United States)

Miao, Dao-yi; Yang, Guo-jing; Zhang, Ling-zhou; Wu, Jian-wei

2015-10-01

To compare the clinical effects and safety of dynamic external fixtor combined with limited internal fixation and cross K-wires fixation for the treatment of close Pilon fractures of the proximal interphalangeal joint. From June 2012 to June 2014, totally 41 patients (45 fingers) with close interphalangeal joint Pilon fracture were treated by dynamic external fixtor combined with limited internal fixation or cross K-wires fixation, and all the patients were followed up. In the dynamic external fixtor combined with limited internal fixation group (group A), there were 21 patients with 22 fingers, including 12 males and 9 females, with an average of (30.6±5.6) years old. In the cross K-wires fixation group (group B), there were 20 patients with 23 fingers, including 11 males and 9 females, with an average of (30.1±5.3) years old. Regular re-examination of X-ray was performed to evaluate the active range of joint motion, fracture healing time, infection rate and postoperative joint motion pain. According to the evaluation criteria of upper extremity function issued by the Hand Surgery Society of Chinese Medical Association, the excellent and good cases of group A was up to 19 and 13 for group B. The evaluation results has significant differences (Z=2.558, P=0.011). The excellent and good rate of group A was obviously higher than that of group B. The average bone union time of group A was (7.9±2.1) weeks, and (8.1±2.3) weeks for group B. There was no significant difference on the mean healing time (t=-0.304, P=0.762). The infection fingers of group A was 5, and 1 for group B. The difference between the results was statistically significant (χ2=3.287, Pexternal fixtor combined with limited internal fixation is a reliable and effective method to treat Pilon fractures of the proximal interphalangeal joint. It allows early postoperative functional rehabilitation and restores the joint function.

[Missed diagnosis of hiding posterior marginal fracture of ankle with pronation-external rotation type and its treatment].

Science.gov (United States)

Wang, Jia; Zhang, Yun-Tong; Zhang, Chun-Cai; Tang, Yang

2014-01-01

To analyze causes of missed diagnosis of hiding post-malleolar fractures in treating ankle joint fractures of pronation-external rotation type according to Lauge-Hansen classification and assess its medium-term outcomes. Among 103 patients with ankle joint fracture of pronation-external rotation type treated from March 2002 to June 2010,9 patients were missed diagnosis,including 6 males and 3 females,with a mean age of 35.2 years old (ranged, 18 to 55 years old) . Four patients were diagnosed during operation, 2 patients were diagnosed 2 or 3 days after first surgery and 3 patients came from other hospital. All the patients were treated remedially with lag screws and lock plates internal fixation. After operation,ankle joint function was evaluated according to American Orthopaedic Foot and Ankle Society (AOFAS). All the 9 patients were followed up, and the duration ranged from 14 to 30 months (averaged, 17 months). No incision infection was found, and all incision healed at the first stage. At the latest follow-up, AOFAS was 83.0 +/- 4.4, the score of 4 patients diagnosed during operation was 85.0 +/- 2.9, and the score of 5 patients treated by secondary operation was 81.0 +/- 5.3. All the patients got fracture union observed by X-ray at a mean time of 2.2 months after operation. There were no complications such as internal fixation loosing, broken and vascular or nerve injuries. Ankle joint fracture of pronation-external rotation type may be combined with hiding post-malleolar fractures. So to patients with ankle joint fracture of pronation-external rotation type, lateral X-ray should be read carefully, and if necessary, CT or MRI examination should be performed. If adding lateral X-ray examination after reduction of exterior and interior ankle joint fixation, the missed diagnosis may be avoided.

Joint Tax Audits : Which Countries May Benefit Most?

NARCIS (Netherlands)

Burgers, Irene J.J.; Criclivaia, Diana

2016-01-01

In their joint fight against tax avoidance and tax evasion, international governance organizations have developed different tools. One of these tools is the joint tax audit, in which two or more countries join together to form a single audit team to examine an issue(s)/transaction(s) of one or more

Gastrointestinal disorders in joint hypermobility syndrome/Ehlers-Danlos syndrome hypermobility type: A review for the gastroenterologist.

Science.gov (United States)

Beckers, A B; Keszthelyi, D; Fikree, A; Vork, L; Masclee, A; Farmer, A D; Aziz, Q

2017-08-01

Joint hypermobility syndrome (JHS)/Ehlers-Danlos syndrome hypermobility type (EDS-HT) is the most common hereditary non-inflammatory disorder of connective tissue, characterized by a wide range of symptoms, mainly joint hyperextensibility and musculoskeletal symptoms. A majority of patients also experiences gastrointestinal (GI) symptoms. Furthermore, JHS/EDS-HT has specifically been shown to be highly prevalent in patients with functional GI disorders, such as functional dyspepsia and irritable bowel syndrome. The aim of this review was to examine the nature of GI symptoms and their underlying pathophysiology in JHS/EDS-HT. In addition, we consider the clinical implications of the diagnosis and treatment of JHS/EDS-HT for practicing clinicians in gastroenterology. Observations summarized in this review may furthermore represent the first step toward the identification of a new pathophysiological basis for a substantial subgroup of patients with functional GI disorders. © 2017 John Wiley & Sons Ltd.

A retrospective comparative study of arthroscopic fixation in acute Rockwood type IV acromioclavicular joint dislocation: single versus double paired Endobutton technique.

Science.gov (United States)

Xu, Jian; Liu, Haifeng; Lu, Wei; Li, Dingfu; Zhu, Weimin; Ouyang, Kan; Wu, Bing; Peng, Liangquan; Wang, Daping

2018-05-24

Rockwood type IV acromioclavicular joint (ACJ) dislocation is a trauma usually needs surgical treatment. Paired EndoButton technique (PET) is used in treating such condition. However, the effect of using different types of PET (single versus double PET) for fixation remains controversial. This study aims to evaluate and compare the efficacy of single and double PET and to provide a suitable option for the surgeons. We retrospectively reviewed the charts of patients with acute Rockwood type IV ACJ dislocation who had undergone arthroscopic fixation using single or double PET fixation between March 2009 and March 2015. Seventy-eight consecutive patients identified from chart review were picked and were divided into the single and double PET group with 39 cases in each group. The indexes of visual analog scale score (VAS) for pain, the radiographs of the affected shoulder at different time points of the follow-up, the time of return to activities and sports, the constant functional score, and the Karlsson acromioclavicular joint (ACJ) score, were assessed in a minimum of 2 years postoperation. The average coracoclavicular (CC) and acromioclavicular (AC) distances of the affected joints in the double PET group were significantly smaller than those of the single PET group 2 years postoperation (P  0.05). The mean VAS pain score was not significantly different, while significant difference was found for the number and times of cases return to activities and sports, constant functional score, and Karlsson ACJ score (P < 0.05) between the two groups. Therefore, the double PET group has better outcome than the single PET group. Complications including redislocation, button slippage, erosion, or AC joint instability occurred in the single PET group, while the complication in the double PET group was rare. Compared with the single PET, the double PET group achieved better outcome with less complications in arthroscopically treating acute Rockwood type IV ACJ

Report of the International Review Committee of the joint proposal of the Japan Hadron Facility (KEK) and the Neutron Science Project (JAERI)

International Nuclear Information System (INIS)

1999-08-01

The International Review Committee composed of twelve Japanese and foreign experts was set up under the Research Evaluation Committee of JAERI, and has reviewed the proposed joint project combining JAERI's Neutron Science Project and KEK's Japan Hadron Facility into one major facility. The review meeting took place on April 26-27, 1999, at JAERI Head quarters, Tokyo. According to the points of review given in advance, the review was implemented based on the joint project report submitted and presentations of both institutions. The Research Evaluation Committee received the review report and its explanations from the Review Committee on July 5. The Research Evaluation Committee has acknowledged appropriateness of the review results. This report describes the review results. (author)

How to establish and sustain a joint venture in China.

Science.gov (United States)

Lee, Paul

2008-01-01

Joint ventures with Chinese companies provide one of the most effective ways for international companies to establish a foothold in the booming Chinese economy. The benefits, opportunities and challenges of establishing a joint venture are explored here. Current partnering trends and successful Sino-foreign joint ventures in the fast-growing medical device industry in China are also highlighted.

Reliability of agriculture universal joint shafts based on temperature measuring in universal joint bearing assemblies

Directory of Open Access Journals (Sweden)

Аleksandar Asonja

2015-03-01

Full Text Available This paper presents a research into reliability calculations of agriculture double universal joint shafts based on temperature measuring in cardan-type universal joint bearing assemblies. Special laboratory equipment was developed for this research which is presented in the paper. The objective of this research was to test the real life span of universal joint shafts in the laboratory and in field, to obtain the results which can be used to improve the reliability of universal joint shafts. If the presented research were used along with maintenance measures recommended in the paper and with proper use, the level of reliability of the shafts would be 2.1 times higher. The presented results of the research showed that needle bearings, i.e. bearing assemblies of the joints, are the most critical elements on universal joint shafts and are possible causes of their lower reliability. The second universal joint is the part with the lowest reliability in the observed technical system.

A STUDY ON OSTEOARTHRITIS OF KNEE JOINT

Directory of Open Access Journals (Sweden)

Ayyappan Nair

2016-09-01

Full Text Available BACKGROUND Osteoarthritis is the most common type of arthritis. It is a degenerative disease where, load bearing synovial joints like hip and knee are affected. Usually bilateral, highest incidence is seen after 6th decade of life. It is also common in women post - menopausal age. Osteoarthritis of knee is more common in Asian population because of lifestyle habits like squatting and sitting cross legged. The aetiology of the disease can be multifactorial but usually it is an age associated disease due to wear and tear. The two types of osteoarthritis are, Primary osteoarthritis: It is more common. This occurs in old age due to wear and tear of the joints and Secondary osteoarthritis: In this there is an underlying primary joint disease which leads to degeneration. Any age group can be affected. Predisposing factors are, congenital malformation of joint, trauma, disease involving joints, malalignment, internal derangement and obesity. A sincere effort has been put in this study to understand the Osteoarthritis complications in the elderly population. This study is intended to help the practicing fellow orthopaedicians to understand and thus treat the patient more effectively. METHODS  The study was done in the Department of Orthopaedics, Travancore Medical College at Kollam.  The study was done from June 2014 to June 2016.  Three Hundred Twenty cases who attended in the Department of Orthopaedics were taken for the study.  Detailed History and Clinical Examination was conducted.  All the statistical analysis was done using the latest SPSS software 2015 (California. RESULTS In the present study, the mean age of the population was 62.67 years with a standard deviation of 11.739 years. Crepitus was present in eighty three cases; pain was the chief complaint and was present in two hundred and thirty eight cases. Stiffness was complained in two hundred and fourteen cases and in seventy one cases the patient complained of swelling. On

Joint conference of 17th international Toki conference on physics of flows and turbulence in plasmas and 16th international stellarator/heliotron workshop 2007. Proceedings (2)

International Nuclear Information System (INIS)

2008-01-01

The Joint Conference of 16th International Stellarator/Heliotron Workshop (ISHW) and 17th International Toki Conference (ITC) was held in Toki (Japan) October 15-19 2007 and organized by the National Institute for Fusion Science (NIFS). More than 200 experts in stellarator/heliotron research from Australia, Austria, Belgium, Germany, Japan, Russia, Serbia, Spain, Ukraine and the United States of America gathered at the conference. The International Advisory committee chaired by O. Motojima, the International Program Committee (IPC) chaired by C. Hidalgo and the Local Organizing Committee (LOC) chaired by H. Yamada have played the leading role in the elaboration of the scientific programme of the joint conference. This series of Stellarator Workshops is organized biennially in the framework of the International Energy Agency (IEA) Implementing Agreement on the Stellarator Concept. NIFS has organized the ITC as an annual meeting for fusion related sciences since its establishment in 1989. The IPC arranged 2 plenary talks, 1 review talk, 2 tutorial talks, 23 invited talks in addition to 201 contributed presentations. The driving force behind magnetically confined fusion research is the design of magnetic traps to confine high temperature plasmas of deuterium and tritium in reactor relevant conditions (i.e. to produce self-sustaining fusion reactions to release useful energy). Although next step magnetic confinement devices, such as ITER, will be based on the tokamak idea, it is not clear that a unique magnetic configuration will be the answer to the various possible applications of fusion energy and hence other magnetic confinement concepts should be explored. The stellarator is an alternative magnetic confinement concept, with the specific advantages of an intrinsically steady state magnetic field an disruption free operation. The 3D magnetic field geometry in stellarators needs an elaborate optimization to guarantee confinement properties which meet the basic

Joint conference of 17th international Toki conference on physics of flows and turbulence in plasmas and 16th international stellarator/heliotron workshop 2007. Proceedings (1)

International Nuclear Information System (INIS)

2008-01-01

The Joint Conference of 16th International Stellarator/Heliotron Workshop (ISHW) and 17th International Toki Conference (ITC) was held in Toki (Japan) October 15-19 2007 and organized by the National Institute for Fusion Science (NIFS). More than 200 experts in stellarator/heliotron research from Australia, Austria, Belgium, Germany, Japan, Russia, Serbia, Spain, Ukraine and the United States of America gathered at the conference. The International Advisory committee chaired by O. Motojima, the International Program Committee (IPC) chaired by C. Hidalgo and the Local Organizing Committee (LOC) chaired by H. Yamada have played the leading role in the elaboration of the scientific programme of the joint conference. This series of Stellarator Workshops is organized biennially in the framework of the International Energy Agency (IEA) Implementing Agreement on the Stellarator Concept. NIFS has organized the ITC as an annual meeting for fusion related sciences since its establishment in 1989. The IPC arranged 2 plenary talks, 1 review talk, 2 tutorial talks, 23 invited talks in addition to 201 contributed presentations. The driving force behind magnetically confined fusion research is the design of magnetic traps to confine high temperature plasmas of deuterium and tritium in reactor relevant conditions (i.e. to produce self-sustaining fusion reactions to release useful energy). Although next step magnetic confinement devices, such as ITER, will be based on the tokamak idea, it is not clear that a unique magnetic configuration will be the answer to the various possible applications of fusion energy and hence other magnetic confinement concepts should be explored. The stellarator is an alternative magnetic confinement concept, with the specific advantages of an intrinsically steady state magnetic field an disruption free operation. The 3D magnetic field geometry in stellarators needs an elaborate optimization to guarantee confinement properties which meet the basic

Imaging findings of charcot joint

International Nuclear Information System (INIS)

Meng Quanfei; Zhou Chunxiang; Chen Yingming; Jiang Bo

2003-01-01

Objective: To analyze the MRI characters of Charcot joint, and to evaluate the diagnostic value of X-ray, CT, and MRI on Charcot joint. Methods: Eight patients with 8 Charcot joints underwent X-ray, CT, and MR examinations. 6 of them had syringomyelia, 1 patient had injury of the spinal cord, and 1 case had diabetes. All 8 patients had sensory reduction or deficit in the sick extremities. Results: There were two types of Charcot joint, hypertrophic and atrophic. Radiographic and CT features of hypertrophic joint (n=3) showed hyperostotic osteosclerosis and mammoth osteophytes in the sick bones, periarticular ossification, and articular disorganization. Radiographic and CT features of atrophic joint (n=5) showed extensive bone resorption (destruction), periarticular debris, and articular disorganization. Main MRI features of Charcot joint included hydrarthrosis within joint capsule, thickened, loose, and elongated joint capsule with para-joint, peri-diaphysis, and inter-muscular extension in a pseudopodia pattern. The irregular joint capsule wall was presented as mild hypointensity on T 1 WI, slight hyper-intensity on T 2 WI, and was markedly enhanced after Gd-DTPA was administrated, which was considered as a characteristic manifestation of the lesion. Soft tissue mass containing hypo-intense stripes on both T 1 WI and T 2 WI was commonly noted adjacent to the involved joint. Conclusion: X-rays plain film is the first choice for the diagnosis of Charcot joint, and MRI is pretty useful in the diagnosis of Charcot joint

Comparison of implant component fractures in external and internal type: A 12-year retrospective study.

Science.gov (United States)

Yi, Yuseung; Koak, Jai-Young; Kim, Seong-Kyun; Lee, Shin-Jae; Heo, Seong-Joo

2018-04-01

The aim of this study was to compare the fracture of implant component behavior of external and internal type of implants to suggest directions for successful implant treatment. Data were collected from the clinical records of all patients who received WARANTEC implants at Seoul National University Dental Hospital from February 2002 to January 2014 for 12 years. Total number of implants was 1,289 and an average of 3.2 implants was installed per patient. Information about abutment connection type, implant locations, platform sizes was collected with presence of implant component fractures and their managements. SPSS statistics software (version 24.0, IBM) was used for the statistical analysis. Overall fracture was significantly more frequent in internal type. The most frequently fractured component was abutment in internal type implants, and screw fracture occurred most frequently in external type. Analyzing by fractured components, screw fracture was the most frequent in the maxillary anterior region and the most abutment fracture occurred in the maxillary posterior region and screw fractures occurred more frequently in NP (narrow platform) and abutment fractures occurred more frequently in RP (regular platform). In external type, screw fracture occurred most frequently, especially in the maxillary anterior region, and in internal type, abutment fracture occurred frequently in the posterior region. placement of an external type implant rather than an internal type is recommended for the posterior region where abutment fractures frequently occur.

Omnidirectional Internal Fixation by Double Approaches for Treating Rüedi-Allgöwer Type III Pilon Fractures.

Science.gov (United States)

Dai, Chong-Hua; Sun, Jun; Chen, Kun-Quan; Zhang, Hui-Bo

In the present study, we explored the effectiveness and complications of omnidirectional internal fixation using a double approach for treating Rüedi-Allgöwer type III pilon fractures. A retrospective analysis was performed of 19 cases of Rüedi-Allgöwer type III unilateral closed pilon fracture. With preoperative preparation and correct surgical timing, the reduction was performed using anteromedial and posterolateral approaches, and the fracture fragments were fixed by omnidirectional internal fixation. Imaging evaluation was performed using the Burwell-Charnley scoring system. The Johner-Wruhs scoring system was used to assess the functional status of the patients. A comprehensive evaluation of efficacy was performed using a 5-point Likert score. The complications were also recorded and analyzed. All patients were followed up for an average of 16.2 months. The operative incisions of 15 cases healed by primary intent and with delayed healing in 4. All patients had achieved bony union at an average of 16 weeks postoperatively. No deep infection, broken nail or withdrawn nail, exposed plate, or skin flap necrosis occurred. The Burwell-Charnley imaging evaluation showed that 14 patients had anatomic reduction of the articular surface and 5 had acceptable reduction. Using the Johner-Wruhs scoring system, the results were excellent for 8, good for 7, fair for 2, and poor for 2 patients; the combined rate of excellent and good results was 78.9%. The Likert score of efficacy self-reported by the patients was 3 to 4 points for 12 patients, 2 points for 4 patients, and 0 to 1 point for 3 patients. The Likert score of therapeutic efficacy reported by the physicians was 3 to 4 points for 10 patients, 2 points for 5 patients, and 0 to 1 point for 4 patients. Omnidirectional internal fixation using double approaches was an effective method to treat Rüedi-Allgöwer type III pilon fractures with satisfactory reduction and rigid fixation, good joint function recovery, and

Shoulder function, pain and health related quality of life in adults with joint hypermobility syndrome/Ehlers-Danlos syndrome-hypermobility type

DEFF Research Database (Denmark)

Johannessen, Elise Christine; Reiten, Helle Sundnes; Løvaas, Helene

2016-01-01

Purpose To investigate shoulder function, pain and Health-Related Quality of life (HRQoL) among adults with joint hypermobility syndrome/Ehlers-Danlos syndrome-hypermobility type (JHS/EDS-HT), compared with the general population (controls). Method In a cross-sectional study using postal survey...

Fiscal 1998 international research cooperation project. Feasibility study report on excavation of international joint research seeds; 1998 nendo kokusai kyoryoku jigyo seika hokokusho. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study (FS) was made on excavation of international joint research seeds for developed countries. As FS themes, 6 themes were selected among applied 11 ones. China was interested in the joint research on improvement of a cetane number by ring-opening of LCO from fluid catalytic crackers through hydrogenation for Arabian crude oil, although China has an experience for domestic one. Since France and the USA are in the early developmental stage of practical atmospheric temperature and pressure conversion technology of lower hydrocarbon after the basic research stage, study was made on the possibility of a joint research. The other themes are as follows: Oil resource and energy conservation technology by recycling general plastics and industrial synthetic resins, advanced solid catalyst regulating technology by physicochemical technique and its application to next-generation oil refining processes, structure analysis of asphaltene and reaction mechanism analysis of heavy oil by computer simulation, and production technology of ultra-precisely controlled catalytic materials. (NEDO)

26 CFR 20.2040-1 - Joint interests.

Science.gov (United States)

2010-04-01

... Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) ESTATE AND GIFT TAXES ESTATE TAX; ESTATES OF DECEDENTS DYING AFTER AUGUST 16, 1954 Gross Estate § 20.2040-1 Joint interests. (a... owner or owners by gift, devise, bequest, or inheritance, the decedent's fractional share of the...

PANCREATIC DIABETES TYPE 2 IN CHILDREN AND ADOLESCENTS: INTERNATIONAL RECOMMENDATIONS

Directory of Open Access Journals (Sweden)

O.V. Vasyukova

2009-01-01

Full Text Available Violent growth of type 2 diabetes mellitus (DM morbidity in children and adolescents is spread all around the world. Peculiarities of DM type 2 in this age group are: absence of determined diagnostic criteria, difficulty of differential diagnosis with DM type 1, early development of complications. International Society of Pediatric and Adolescent Diabetes propose Guideline of DM type 2 management, which consider main questions of diagnostics, treatment and prophylaxis of this disease. The agent of choice for treatment of DM type 2 in children upwards 10 years is metformin.Key words: children, diabetes mellitus type 2, diagnostics, treatment.(Voprosy sovremennoi pediatrii — Current Pediatrics. 2009;8(2:49-53

International cooperation for disaster management -- Romanian-American experience in the achievement of a joint exercise using decision support tools for radiological emergency

International Nuclear Information System (INIS)

Qualls, J.R.; Botirca, R.; Gabor, A.; Miron, A.

1995-01-01

International coordination and cooperation is rewarding but at the same time very challenging. This paper will discuss the Romanian perspective on technology transfer, its problems and its advantages. Further, the discussion will take place in the context of preparing for an international conference while at the same time exchanging civil defense expertise. The American perspective on the same subject will also be presented with healthy doses of mutual explanations. The final portion of the paper will present the joint lessons learned from the newly created interfaces and what it holds for the future. The paper aims to present the Romanian and American experts' opinion about the demonstration of using computer technology for helping the international cooperation in the field of disaster management

Knee joint mobilization reduces secondary mechanical hyperalgesia induced by capsaicin injection into the ankle joint.

Science.gov (United States)

Sluka, K A; Wright, A

2001-01-01

Joint mobilization is a treatment approach commonly used by physical therapists for the management of a variety of painful conditions. However, the clinical effectiveness when compared to placebo and the neurophysiological mechanism of action are not known. The purpose of this study was to establish that application of a manual therapy technique will produce antihyperalgesia in an animal model of joint inflammation and that the antihyperalgesia produced by joint mobilization depends on the time of treatment application. Capsaicin (0.2%, 50 microl) was injected into the lateral aspect of the left ankle joint and mechanical withdrawal threshold assessed before and after capsaicin injection in Sprague-Dawley rats. Joint mobilization of the ipsilateral knee joint was performed 2 h after capsaicin injection for a total of 3 min, 9 min or 15 min under halothane anaesthesia. Control groups included animals that received halothane for the same time as the group that received joint mobilization and those whose limbs were held for the same duration as the mobilization (no halothane). Capsaicin resulted in a decreased mechanical withdrawal threshold by 2 h after injection that was maintained through 4 h. Both 9 and 15 min of mobilization, but not 3 min of mobilization, increased the withdrawal threshold to mechanical stimuli to baseline values when compared with control groups. The antihyperalgesic effect of joint mobilization lasted 30 min. Thus, joint mobilization (9 or 15 min duration) produces a significant reversal of secondary mechanical hyperalgesia induced by intra-articular injection of capsaicin. Copyright 2001 European Federation of Chapters of the International Association for the Study of Pain.

The Ageing Effect of Mechanical Joints on the Tyre/Joint Noises Monitored by a Control Vehicle Method without Traffic Disturbance

Directory of Open Access Journals (Sweden)

C. K. Wong

2013-01-01

Full Text Available This paper studies the ageing effect of mechanical joints reflecting from the tyre/joint impacting noise by measuring the vehicle structure-borne noise change. Field data is collected applying two measurement methods suitable for newly installed and existing old expansion joints. The measurement methodology is improved by designing and applying a trailer for equipment installation. The main advantage of this method is not to disturb existing traffic by lane closure for measurement. Field measurements were conducted regularly for a study period up to 16 months after new joint replacement to monitor the variation of the structure-borne noise change inside a test vehicle while passing through mechanical joints. Empirical relationship is developed based on the field data of the roadside airborne noise change and the vehicle structure-borne noise change. The roadside tyre/joint noises could be converted using calibrated empirical formula. Key result findings include the following. (1 The vehicle structure-borne noise change is found smallest during the 3rd–6th months even lower than that measured when a new joint is installed. The structure-borne noise change then keeps increasing afterwards till the end of the study period. (2 Similar observations are found in all study cases incorporating various mechanical joint types and test vehicle types.

Tightening unit EZ 250 for VVER 1000 type reactor pressure vessel head flange joints

International Nuclear Information System (INIS)

Ruchar, Miloslav; Nadenik, Tomas; Kroj, Ludek

2010-01-01

The programme of flange joints tightening by seals made of expanded graphite for VVER 440 and VVER 1000 reactor head flange joints is highlighted, and tightening units of row EZ 650 and EZ 650 TK and KNI for VVER 440 reactor head flange joints and EZ 250 tightening unit for VVER 1000 reactor head flange joints are described in detail. The main advantages of electronically controlled tightening units include: Precise and uniform compression of the gasket during the tightening procedure; Automated solution to the graphite relaxing problem during tightening; Possibility of diagnosis of the thread status of the joints being tightened; Alleviation of operator's tough work; Shorter time of tensioning associated with a lower collective doses; Quick preparation of tightening procedure report from the data measured; Calibration renewal is possible in advance at time of unit storage without the need to place it on a real joint. (P.A.)

26 CFR 1.6013-2 - Joint return after filing separate return.

Science.gov (United States)

2010-04-01

... the case of a joint return made under section 6013(b), the period of limitations provided in sections... (c)(1) of this section, relating to the application of sections 6501 and 6651 with respect to a joint... 26 Internal Revenue 13 2010-04-01 2010-04-01 false Joint return after filing separate return. 1...

U.S. Continuing Involvement with the Joint Convention

International Nuclear Information System (INIS)

Stewart, L.; Tonkay, D.; Regnier, E.; Schultheisz, D.; Gnugnoli, G.

2009-01-01

The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (Joint Convention) is an international convention, under the auspices of the International Atomic Energy Agency (IAEA). It is a companion to a suite of international conventions on nuclear safety and physical security, which serve to promote a global culture for the safe use of radioactive materials. The Joint Convention is an official international treaty, and as such, there are obligations on the part of the United States. Those nations having ratified the Joint Convention are designated as 'Contracting Parties.' Nations that are not IAEA Member States may also become Contracting Parties to the Joint Convention, although none has done so. The primary obligations are threefold. The first is to prepare a national report, which addresses the national safety program in radioactive waste management, spent nuclear fuel management, and disused sealed sources. As the U.S. prepares a national report, other Contracting Parties to the Joint Convention also prepare their national reports, which leads to the second obligation on the part of the Contracting Parties. This is the obligation to review other countries' national reports. The last specific obligation is to actively participate in the triennial peer review meeting, referred to as the Review Meeting of the Contracting Parties. The U.S. ratified the Joint Convention in 2003, just prior to the First Review Meeting of the Contracting Parties, and has participated fully therein in the ensuing Review Meetings. Because of the benefits in active participation, it is important for the U.S. to maintain its leadership role in promoting its ratification in the global setting, as well as in more focused regions. Because of the important benefits associated with active participation, the U.S. has strongly supported a Regional Conference Initiative outreach program to increase membership. To launch the Initiative, the U

β-arrestins negatively control human adrenomedullin type 1-receptor internalization

International Nuclear Information System (INIS)

Kuwasako, Kenji; Kitamura, Kazuo; Nagata, Sayaka; Sekiguchi, Toshio; Danfeng, Jiang; Murakami, Manabu; Hattori, Yuichi; Kato, Johji

2017-01-01

Adrenomedullin (AM) is a potent hypotensive peptide that exerts a powerful variety of protective effects against multiorgan damage through the AM type 1 receptor (AM 1 receptor), which consists of the calcitonin receptor-like receptor (CLR) and receptor activity-modifying protein 2 (RAMP2). Two β-arrestin (β-arr) isoforms, β-arr-1 and β-arr-2, play a central role in the agonist-induced internalization of many receptors for receptor resensitization. Notably, β-arr-biased agonists are now being tested in phase II clinical trials, targeting acute pain and acute heart failure. Here, we examined the effects of β-arr-1 and β-arr-2 on human AM 1 receptor internalization. We constructed a V5-tagged chimera in which the cytoplasmic C-terminal tail (C-tail) of CLR was replaced with that of the β 2 -adrenergic receptor (β 2 -AR), and it was transiently transfected into HEK-293 cells that stably expressed RAMP2. The cell-surface expression and internalization of the wild-type or chimeric receptor were quantified by flow cytometric analysis. The [ 125 I]AM binding and the AM-induced cAMP production of these receptors were also determined. Surprisingly, the coexpression of β-arr-1 or -2 resulted in significant decreases in AM 1 receptor internalization without affecting AM binding and signaling prior to receptor internalization. Dominant-negative (DN) β-arr-1 or -2 also significantly decreased AM-induced AM 1 receptor internalization. In contrast, the AM-induced internalization of the chimeric AM 1 receptor was markedly augmented by the cotransfection of β-arr-1 or -2 and significantly reduced by the coexpression of DN-β-arr-1 or -2. These results were consistent with those seen for β 2 -AR. Thus, both β-arrs negatively control AM 1 receptor internalization, which depends on the C-tail of CLR. - Highlights: • We found that β-arrestins 1 and 2 negatively control agonist-induced GPCR internalization. • β-arrestins 1 and 2 significantly inhibits the AM

U.S. Perspectives on the Joint Convention

International Nuclear Information System (INIS)

Strosnider, J.; Federline, M.; Camper, L.; Abu-Eid, R.; Gnugnoli, G.; Gorn, J.; Bubar, P.; Tonkay, D.

2006-01-01

The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (Joint Convention) is an international convention, under the auspices of the International Atomic Energy Agency (IAEA). It is a companion to a suite of international conventions on nuclear safety and physical security, which serve to promote a global culture for the safe use of radioactive materials. Although the U.S. was the first nation to sign the Joint Convention on September 29, 1997, the ratification process was a challenging experience for the U.S., in the face of legislative priorities dominated by concerns for national security and threats from terrorism after September 11, 2001. Notwithstanding these prevailing circumstances, the U.S. ratified the Joint Convention in 2003, just prior to the First Review Meeting of the Contracting Parties, and participated fully therein. For the United States, participation as a Contracting Party provides many benefits. These range from working with other Parties to harmonize international approaches to achieve strong and effective nuclear safety programs on a global scale, to stimulating initiatives to improve safety systems within our own domestic programs, to learning about technical innovations by other Parties that can be useful to U.S. licensees, utilities, and industry in managing safety and its associated costs in our waste management activities. The Joint Convention process also provides opportunities to identify future areas of bilateral and multilateral technical and regulatory cooperation with other Parties, as well as an opportunity for U.S. vendors and suppliers to broaden their market to include foreign clients for safety improvement equipment and services. The Joint Convention is consistent with U.S. foreign policy considerations to support, as a priority, the strengthening of the worldwide safety culture in the use of nuclear energy. Because of its many benefits, we believe it is important to take

Internal Friction And Instabilities Of Rotors

Science.gov (United States)

Walton, J.; Artiles, A.; Lund, J.; Dill, J.; Zorzi, E.

1992-01-01

Report describes study of effects of internal friction on dynamics of rotors prompted by concern over instabilities in rotors of turbomachines. Theoretical and experimental studies described. Theoretical involved development of nonlinear mathematical models of internal friction in three joints found in turbomachinery - axial splines, Curvic(TM) splines, and interference fits between smooth cylindrical surfaces. Experimental included traction tests to determine the coefficients of friction of rotor alloys at various temperatures, bending-mode-vibration tests of shafts equipped with various joints and rotordynamic tests of shafts with axial-spline and interference-fit joints.

β-arrestins negatively control human adrenomedullin type 1-receptor internalization.

Science.gov (United States)

Kuwasako, Kenji; Kitamura, Kazuo; Nagata, Sayaka; Sekiguchi, Toshio; Danfeng, Jiang; Murakami, Manabu; Hattori, Yuichi; Kato, Johji

2017-05-27

Adrenomedullin (AM) is a potent hypotensive peptide that exerts a powerful variety of protective effects against multiorgan damage through the AM type 1 receptor (AM 1 receptor), which consists of the calcitonin receptor-like receptor (CLR) and receptor activity-modifying protein 2 (RAMP2). Two β-arrestin (β-arr) isoforms, β-arr-1 and β-arr-2, play a central role in the agonist-induced internalization of many receptors for receptor resensitization. Notably, β-arr-biased agonists are now being tested in phase II clinical trials, targeting acute pain and acute heart failure. Here, we examined the effects of β-arr-1 and β-arr-2 on human AM 1 receptor internalization. We constructed a V5-tagged chimera in which the cytoplasmic C-terminal tail (C-tail) of CLR was replaced with that of the β 2 -adrenergic receptor (β 2 -AR), and it was transiently transfected into HEK-293 cells that stably expressed RAMP2. The cell-surface expression and internalization of the wild-type or chimeric receptor were quantified by flow cytometric analysis. The [ 125 I]AM binding and the AM-induced cAMP production of these receptors were also determined. Surprisingly, the coexpression of β-arr-1 or -2 resulted in significant decreases in AM 1 receptor internalization without affecting AM binding and signaling prior to receptor internalization. Dominant-negative (DN) β-arr-1 or -2 also significantly decreased AM-induced AM 1 receptor internalization. In contrast, the AM-induced internalization of the chimeric AM 1 receptor was markedly augmented by the cotransfection of β-arr-1 or -2 and significantly reduced by the coexpression of DN-β-arr-1 or -2. These results were consistent with those seen for β 2 -AR. Thus, both β-arrs negatively control AM 1 receptor internalization, which depends on the C-tail of CLR. Copyright © 2017 Elsevier Inc. All rights reserved.

Running in ostriches (Struthio camelus): three-dimensional joint axes alignment and joint kinematics.

Science.gov (United States)

Rubenson, Jonas; Lloyd, David G; Besier, Thor F; Heliams, Denham B; Fournier, Paul A

2007-07-01

Although locomotor kinematics in walking and running birds have been examined in studies exploring many biological aspects of bipedalism, these studies have been largely limited to two-dimensional analyses. Incorporating a five-segment, 17 degree-of-freedom (d.f.) kinematic model of the ostrich hind limb developed from anatomical specimens, we quantified the three-dimensional (3-D) joint axis alignment and joint kinematics during running (at approximately 3.3 m s(-1)) in the largest avian biped, the ostrich. Our analysis revealed that the majority of the segment motion during running in the ostrich occurs in flexion/extension. Importantly, however, the alignment of the average flexion/extension helical axes of the knee and ankle are rotated externally to the direction of travel (37 degrees and 21 degrees , respectively) so that pure flexion and extension at the knee will act to adduct and adbuct the tibiotarsus relative to the plane of movement, and pure flexion and extension at the ankle will act to abduct and adduct the tarsometatarsus relative to the plane of movement. This feature of the limb anatomy appears to provide the major lateral (non-sagittal) displacement of the lower limb necessary for steering the swinging limb clear of the stance limb and replaces what would otherwise require greater adduction/abduction and/or internal/external rotation, allowing for less complex joints, musculoskeletal geometry and neuromuscular control. Significant rotation about the joints' non-flexion/extension axes nevertheless occurs over the running stride. In particular, hip abduction and knee internal/external and varus/valgus motion may further facilitate limb clearance during the swing phase, and substantial non-flexion/extension movement at the knee is also observed during stance. Measurement of 3-D segment and joint motion in birds will be aided by the use of functionally determined axes of rotation rather than assumed axes, proving important when interpreting the

Simultaneous Middle Third Clavicle Fracture and Type 3 Acromioclavicular Joint Dislocation; A Case Report

Science.gov (United States)

Solooki, Saeed; Azad, Ali

2014-01-01

Simultaneous middle third clavicle fracture and acromioclavicular joint dislocation is a rare combination injury, as a result of high-energy trauma. We report a patient with a middle third clavicle fracture and ipsilateral grade three-acromioclavicular joint dislocation, which is a rare combination. The patient wanted to get back to work as soon as possible, so the fracture was fixed with reconstruction plate after open reduction and plate contouring; and acromioclavicular joint dislocation was reduced and fixed with two full threaded cancellous screws. One screw was inserted through the plate to the coracoid process. Clinical and radiographic finding revealed complete union of clavicle fracture and anatomical reduction of acromioclavicular joint with pain free full joint range of motion one year after operation. PMID:25207318

Fatigue properties of dissimilar metal laser welded lap joints

Science.gov (United States)

Dinsley, Christopher Paul

This work involves laser welding austenitic and duplex stainless steel to zinc-coated mild steel, more specifically 1.2mm V1437, which is a Volvo Truck Coiporation rephosphorised mild steel. The work investigates both tensile and lap shear properties of similar and dissimilar metal laser welded butt and lap joints, with the majority of the investigation concentrating on the fatigue properties of dissimilar metal laser welded lap joints. The problems encountered when laser welding zinc-coated steel are addressed and overcome with regard to dissimilar metal lap joints with stainless steel. The result being the production of a set of guidelines for laser welding stainless steel to zinc-coated mild steel. The stages of laser welded lap joint fatigue life are defined and the factors affecting dissimilar metal laser welded lap joint fatigue properties are analysed and determined; the findings suggesting that dissimilar metal lap joint fatigue properties are primarily controlled by the local stress at the internal lap face and the early crack growth rate of the material at the internal lap face. The lap joint rotation, in turn, is controlled by sheet thickness, weld width and interfacial gap. Laser welded lap joint fatigue properties are found to be independent of base material properties, allowing dissimilar metal lap joints to be produced without fatigue failure occurring preferentially in the weaker parent material, irrespective of large base material property differences. The effects of Marangoni flow on the compositions of the laser weld beads are experimentally characterised. The results providing definite proof of the stirring mechanism within the weld pool through the use of speeds maps for chromium and nickel. Keywords: Laser welding, dissimilar metal, Zinc-coated mild steel, Austenitic stainless steel, Duplex stainless steel, Fatigue, Lap joint rotation, Automotive.

GREEN DIPLOMACY-A NEW TYPE OF INTERNATIONAL COOPERATION (II

Directory of Open Access Journals (Sweden)

Elena IFTIME

2014-07-01

Full Text Available We mention our attempt in a broader context reserved to a generous theme, of a great complexity and of a strict actuality that aims the planet’s health, of human and of other forms of living and nonliving forms of life. Particularly insisting on legal international coordinates of environmental protection and conservation, through which are being accomplished the valences of human’s right to a prosperous, healthy and ecologically balanced environment. This right occupies a central place among human rights, one of those essential gifts of nature to which no one should be detrimental to. It is considered to be a law of human solidarity consecrated by international and internal regulations, which involves in its content: the right to live in an unpolluted environment, which is not degraded by activities that can affect the environment, health, human welfare, sustainable development of society; the right to the highest medical care, unaffected by environmental degradation; right to a healthy working environment; right to benefit of durable usage of nature and its resources, the right to adequate water resources and food. This valences exercise of this right in the context of each state’s internal affairs, but especially in the life of international community, involves a new type of international cooperation suggestively called green diplomacy. It is a special form of the classical diplomacy, adapted to the specific and universality of environmental problems, particularly in the second half of the second century onwards. A diplomacy that seeks to harmonize the interests of a state and other’s interests along with the interests of every human being on the Planet, concerning the conservation and development of natural conditions of life. The major objective of this modern type of diplomacy is highlighted to empower the human beings, the micro and macro human community towards protecting, conserving and sustainable development of the Earth�

Against which human papillomavirus types shall we vaccinate and screen? The international perspective.

NARCIS (Netherlands)

Munoz, N.; Bosch, F.X.; Castellsague, X; Diaz, M; Sanjose, de S; Hammouda, D; Shah, K.V.; Meijer, C.J.L.M.

2004-01-01

At least 15 types of HPV have been associated with cervical cancer, but current HPV vaccines confer only type-specific immunity. To determine geographic variations in the HPV type distribution in cervical cancer, we carried out a pooled analysis of data from an international survey of HPV types in

[Antero-medial incision of knee joint for the treatment of intercondylar fracture of femur].

Science.gov (United States)

Yin, Zi-Fei; Sun, Bin-Feng; Yang, Xiao-Hai; Wang, Qing; Qian, Ping-Kang; Wu, Xiao-Feng; Xu, Feng

2017-12-25

To explore the clinical effect of antero-medial incision of knee joint in treating intercondylar fracture of femur. From September 2012 to March 2015, 24 patients with intercondylar fracture of femur were selected, including 17 males and 7 females, aged from 20 to 65 years old with an average of(38.3±9.5) years old. Among them, 12 cases were caused by traffic accident, 8 cases were caused by falling injury and 4 cases were caused by falling down. All patients were closed fractures. The time from injury to hospital was from 30 min to 8 h with an average of(2.2±0.3) h. According to AO classification, 4 cases were type B1, 3 type B2, 2 type B3, 5 type C1, 6 type C2 and 4 type C3. All patients were treated with antero-medial incision of knee joint. Operative time, blood loss and postoperative complications were observed and recovery of keen function was evaluated by Kolmert scoring. All patients were followed-up from 6 to 12 months with average of (9.0±1.7) months. Operative time ranged from 50 to 90 min with an average of (70.0±8.2) min; blood loss ranged from 90 to 400 ml with an average of (180±36) ml; negative pressure flow was from 30 to 90 ml, with an average of (50.0±7.1) ml. All fracture were healed at stage I without loosening of internal fixator, fracture nonunion, and deep vein thrombosis. According to Kolmert scoring, 16 patients got excellent result, 5 patients good and 3 fair. Antero-medial incision of knee joint in treating intercondylar fracture of femur, which has advantages of good fracture reduction, less injury of soft tissue and simple operation, could obtain good clinical results.

Infant joint attention, neural networks and social cognition.

Science.gov (United States)

Mundy, Peter; Jarrold, William

2010-01-01

Neural network models of attention can provide a unifying approach to the study of human cognitive and emotional development (Posner & Rothbart, 2007). In this paper we argue that a neural network approach to the infant development of joint attention can inform our understanding of the nature of human social learning, symbolic thought process and social cognition. At its most basic, joint attention involves the capacity to coordinate one's own visual attention with that of another person. We propose that joint attention development involves increments in the capacity to engage in simultaneous or parallel processing of information about one's own attention and the attention of other people. Infant practice with joint attention is both a consequence and an organizer of the development of a distributed and integrated brain network involving frontal and parietal cortical systems. This executive distributed network first serves to regulate the capacity of infants to respond to and direct the overt behavior of other people in order to share experience with others through the social coordination of visual attention. In this paper we describe this parallel and distributed neural network model of joint attention development and discuss two hypotheses that stem from this model. One is that activation of this distributed network during coordinated attention enhances the depth of information processing and encoding beginning in the first year of life. We also propose that with development, joint attention becomes internalized as the capacity to socially coordinate mental attention to internal representations. As this occurs the executive joint attention network makes vital contributions to the development of human symbolic thinking and social cognition. Copyright © 2010 Elsevier Ltd. All rights reserved.

APEX-CAMBIUM: A Case Study in Advantages and Challenges of International Cooperation for the International Space Station

Science.gov (United States)

Cox, David; Buckley, Nicole

2008-01-01

It is generally agreed that space science benefits from an international collaboration. There are different mechanisms to make this happen but to recognize opportunities requires a keen awareness of the activities, people and respective strengths. Apex- Cambium is a joint Canadian Space Agency (CSA)-National Aeronautics and Space Administration (NASA) initiative. It was made possible in large part through the good relations and shared willingness to meet a common objective, that of doing exciting science in space. The actual mechanics of bringing an international project together can be divided into two perspectives: programmatic and implementation. The programmatic component includes recognizing complementarities, bringing science together, and the need to have Agencies approve and accept joint responsibility for the mission. The implementation component involves working to define science requirements, available resources and assigning individual responsibilities while keeping the overall success criteria as a collective objective. The APEX-CAMB11.JM mission will be described from the point of view of both CSA and NASA. Suggestions on how to facilitate these types of initiatives will be provided and highlights of the APEX-Cambium collaboration will be provided.

Gonococcal Prosthetic Joint Infection.

Science.gov (United States)

Gassiep, Ian; Gilpin, Bradley; Douglas, Joel; Siebert, David

2017-01-01

Neisseria gonorrhoea is a common sexually transmitted infection worldwide. Disseminated gonococcal infection is an infrequent presentation and rarely can be associated with septic arthritis. Incidence of this infection is rising, both internationally and in older age groups. We present the first documented case of N. gonorrhoea prosthetic joint infection which was successfully treated with laparoscopic debridement and antimicrobial therapy.

Exercise beliefs and behaviours of individuals with Joint Hypermobility syndrome/Ehlers-Danlos syndrome - hypermobility type.

Science.gov (United States)

Simmonds, Jane V; Herbland, Anthony; Hakim, Alan; Ninis, Nelly; Lever, William; Aziz, Qasim; Cairns, Mindy

2017-11-10

To explore exercise beliefs and behaviours of individuals with Joint Hypermobility syndrome/Ehlers-Danlos syndrome - hypermobility type and to explore patient experiences of physiotherapy. A cross sectional questionnaire survey design was used to collect quantitative and qualitative data from adult members of the Hypermobility Syndromes Association and Ehlers-Danlos Syndrome Support UK. Descriptive and inferential statistics were used to analyse the data. Qualitative data was analysed thematically. 946 questionnaires were returned and analysed. Participants who received exercise advice from a physiotherapist were 1.75 more likely to report high volumes of weekly exercise (odds ratio [OR] = 1.75, 95% confidence interval [CI] = 1.30-2.36, p Ehlers-Danlos syndrome - hypermobility type in this survey. Implications for rehabilitation Exercise is a cornerstone of treatment for Ehlers-Danlos syndrome/Ehlers-Danlos syndrome - hypermobility type. Pain, fatigue and fear of injury are frequently reported barriers to exercise. Advice from physiotherapists may significantly influence exercise behaviour. Physiotherapists with condition specific knowledge and good verbal and non-verbal communication facilitate a positive therapeutic experience.

Identification of Nonlinear Micron-Level Mechanics for a Precision Deployable Joint

Science.gov (United States)

Bullock, S. J.; Peterson, L. D.

1994-01-01

The experimental identification of micron-level nonlinear joint mechanics and dynamics for a pin-clevis joint used in a precision, adaptive, deployable space structure are investigated. The force-state mapping method is used to identify the behavior of the joint under a preload. The results of applying a single tension-compression cycle to the joint under a tensile preload are presented. The observed micron-level behavior is highly nonlinear and involves all six rigid body motion degrees-of-freedom of the joint. it is also suggests that at micron levels of motion modelling of the joint mechanics and dynamics must include the interactions between all internal components, such as the pin, bushings, and the joint node.

Differential contributions of specimen types, culturing, and 16S rRNA sequencing in diagnosis of prosthetic joint infections

DEFF Research Database (Denmark)

Larsen, Lone Heimann; Khalid, Vesal; Xu, Yijuan

2018-01-01

to variations in specimen sampling. In this prospective, multidisciplinary study of hip or knee prosthetic failures, we assessed the contributions of different specimen types, extended culture incubations, and 16S rRNA sequencing for diagnosing prosthetic joint infections (PJI). Project specimens included joint...... fluid (JF), bone biopsy specimens (BB), soft-tissue biopsy specimens (STB), and swabs (SW) from the prosthesis, collected in situ, and sonication fluid collected from prosthetic components (PC). Specimens were cultured for 6 (conventional) or 14 days, and 16S rRNA sequencing was performed at study...... completion. Of the 156 patients enrolled, 111 underwent 114 surgical revisions (cases) due to indications of either PJI (n = 43) or AF (n = 71). Conventional tissue biopsy cultures confirmed PJI in 28/43 (65%) cases and refuted AF in 3/71 (4%) cases; one case was not evaluable. Based on these results, minor...

Argue internal audit on how to promote the nuclear power enterprise internal control

International Nuclear Information System (INIS)

Li Xiaoming

2012-01-01

In order to strengthen and standardize enterprise internal control, improve the management level and risk prevention ability, five departments jointly established the basic rules of internal control in enterprises, large and medium-sized enterprises as the national power enterprise, the enterprise internal audit executive power in strengthening and perfecting internal control, and in the enterprise internal control of play an active role. (author)

Design of X-joints in Sandwich Structures for Naval Vessels

DEFF Research Database (Denmark)

Hayman, Brian; Berggreen, Christian; Lundsgaard-Larsen, Christian

2007-01-01

In many naval ships of fibre composite sandwich construction, an X-joint exists where the end bulkhead of the superstructure is attached to the deck, with an internal bulkhead placed in the same vertical plane below the deck. This joint is subjected to alternating tensile and compressive loading...

Work in Progress - Developing Joint Degrees through E-Learning Systems

OpenAIRE

Aguirre Herrera, Sandra; Quemada Vives, Juan; Salvachúa Rodríguez, Joaquín

2008-01-01

The development of Joint Degrees is an important mechanism for opening higher education systems nationwide, adapting them to the international standard, and promoting quality assessment to a broader environment. Since e-Learning systems covers a wide range of academic programs, and as joint degrees such as e-Learning are rapidly growing trends, finding a suitable solution that enables universities to design joint degrees through their own e-Learning systems becomes necessary. This paper intro...

The effects of welded joint characteristics on its properties in HDPE thermal fusion welding

Science.gov (United States)

Dai, Hongbin; Peng, Jun

2017-05-01

In this paper, PE100 pipes with the diameter of 200 mm and the thickness of 11.9 mm were used as material. The welded joints were obtained in different welding pressures with the optimal welding temperature of 220∘C. Reheating process on the welded joints with the temperature of 130∘C was carried out. The joints exhibited X-type, and the cause of X-type joints was discussed. The temperature field in the forming process of welded joints was measured, and tensile and bending tests on welded joints were carried out. The fracture surface of welded joints was observed by scanning electron microscopy (SEM), and crystallinity calculation was taken by X-ray diffraction (XRD). The mechanism of X-type weld profile effects on welded joints properties was analyzed. It was concluded that the mechanical properties of welded joints decrease with the reduced X distance between lines.

Application of numerical method in calculating the internal rate of return of joint venture investment using diminishing musyarakah model

Science.gov (United States)

Ruslan, Siti Zaharah Mohd; Jaffar, Maheran Mohd

2017-05-01

Islamic banking in Malaysia offers variety of products based on Islamic principles. One of the concepts is a diminishing musyarakah. The concept of diminishing musyarakah helps Muslims to avoid transaction which are based on riba. The diminishing musyarakah can be defined as an agreement between capital provider and entrepreneurs that enable entrepreneurs to buy equity in instalments where profits and losses are shared based on agreed ratio. The objective of this paper is to determine the internal rate of return (IRR) for a diminishing musyarakah model by applying a numerical method. There are several numerical methods in calculating the IRR such as by using an interpolation method and a trial and error method by using Microsoft Office Excel. In this paper we use a bisection method and secant method as an alternative way in calculating the IRR. It was found that the diminishing musyarakah model can be adapted in managing the performance of joint venture investments. Therefore, this paper will encourage more companies to use the concept of joint venture in managing their investments performance.

26 CFR 25.2523(d)-1 - Joint interests.

Science.gov (United States)

2010-04-01

...)-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) ESTATE AND GIFT TAXES GIFT TAX; GIFTS MADE AFTER DECEMBER 31, 1954 Deductions § 25.2523(d)-1 Joint interests. Section..., if the donor purchased real property in the name of the donor and the donor's spouse as tenants by...

Sensory innervation of the temporomandibular joint in the mouse.

Science.gov (United States)

Dreessen, D; Halata, Z; Strasmann, T

1990-01-01

The sensory innervation of the temporomandibular joints (TMJs) of 8 STR/IN mice was investigated by means of light and electron microscopy. Through the cutting of complete semithin sections in series it was possible to investigate the joints thoroughly. Additionally, one joint with its nerve supply was reconstructed three-dimensionally with a computerized three-dimensional programme. The reconstruction was based on one complete semithin section series. The joint's nerve supply originates from the nervus auriculotemporalis and additionally from motor branches of the n. mandibularis: n. massetericus, n. pterygoideus lateralis and the nn. temporales posteriores. The greatest number of nerve fibres and endings is located in the dorsolateral part of the joint capsule. They lie only in the stratum fibrosum and subsynovially. Neither the stratum synoviale nor the discus articularis contain any nerve fibres or endings, whereas the peri-articular loose connective tissue is richly innervated. The only type of nerve ending observed within the joint was the free nerve ending, which is assumed to serve not only as a nociceptor but also as a polymodal mechanoreceptor. Merely within the insertion of the musculus pterygoideus lateralis at the collum mandibulae single stretch receptors of the Ruffini type were observed. Ultrastructurally, they correspond to those described in the cat's knee joint. Neither lamellated nor nerve endings of the Golgi or Pacini type were observed in the joint or in the peri-articular connective tissue. The unexpected paucity of nerve fibres and endings in the TMJ itself of the mouse suggests that the afferent information from the joint is less important for position sense and movement than the afferent information from muscles, tendons and periodontal ligaments.

[COMPARISON OF EFFECTIVENESS BETWEEN TWO OPERATIVE TECHNIQUES OF CORACOCLAVICULAR LIGAMENT RECONSTRUCTION FOR TREATMENT OF Tossy TYPE III ACROMIOCLAVICULAR JOINT DISLOCATION].

Science.gov (United States)

Tang, Hongwei; Gao, Sheng; Yin, Yong; Li, Yunfei; Han, Qingtian; Li, Huizhang

2015-11-01

To evaluate and compare the effectiveness of double Endobutton technique and suture anchor combined Endobutton plate in the treatment of Tossy type III acromioclavicular joint dislocation. Between May 2010 and March 2014, a retrospective study was preformed on 56 patients with Tossy type III acromioclavicular joint dislocation. The coracoclavicular ligament was reconstructed with double Endobutton technique in 31 cases (Endobutton group), and with suture anchor combined Endobutton plate in 25 cases (Anchor group). There was no significant difference in age, gender, injury causes, injury side, associated injury, medical comorbidities, and disease duration between 2 groups (P>0.05). The operation time, medical device expenses, postoperative complications, preoperative and postoperative Constant-Murley scores, and postoperative Karlsson grading of the injured shoulder were compared between 2 groups. The average operation time in Endobutton group was significantly greater than that in Anchor group (t = 4.285, P = 0.000); there was no significant difference in the medical device expenses between 2 groups (t = 1.555, P = 0.126). Primary healing of incision was obtained in all patients of 2 groups; no early complications of infection and skin necrosis occurred. All patients were followed up 15.6 months on average (range, 11-35 months). During follow-up, some loss of reduction and ectopic ossification in the coracoclavicular gap were observed in 1 case and 6 cases of Endobutton group, respectively. No recurrence of acromioclavicular joint dislocation, implant fixation loosening and broken, and secondary fractures occurred in the other patients. There was significant difference in the incidence of postoperative complications between 2 groups (P = 0.013). Constant-Murley scores of the injured shoulder significantly increased at 9 months after operation when compared with preoperative values in 2 groups (P 0.05). At last follow-up, there was no significant difference in

Joint Coding/Decoding for Multi-message HARQ

OpenAIRE

Benyouss , Abdellatif; Jabi , Mohammed; Le Treust , Maël; Szczecinski , Leszek

2016-01-01

International audience; In this work, we propose and investigate a new coding strategy devised to increase the throughput of hybrid ARQ (HARQ) transmission over block fading channel. In our proposition, the transmitter jointly encodes a variable number of bits for each round of HARQ. The parameters (rates) of this joint coding can vary and may be based on the negative acknowledgment (NACK) signals provided by the receiver or, on the past (outdated) information about the channel states. The re...

76 FR 5224 - Joint Industry Plan; Notice of Filing of Amendment No. 25 to the Joint Self-Regulatory...

Science.gov (United States)

2011-01-28

... Collection, Consolidation and Dissemination of Quotation and Transaction Information for Nasdaq-Listed... Exchange, Inc., EDGX Exchange, Inc., Financial Industry Regulatory Authority, Inc., International... Joint Self-Regulatory Organization Plan Governing the Collection, Consolidation, and Dissemination of...

The report of joint research over 20 years of the Bulgarian Academy of Sciences and Hiroshima Institute of Technology

OpenAIRE

Tanaka,Takeshi; Vutova,Katia

2014-01-01

The Department of Electronics and Computer Engineering, Hiroshima Institute of Technology (EC-HIT) started the international joint research with the Laboratory “Physical Problems of Electron Beam technologies” of the Institute of Electronics, Bulgarian Academy of Sciences (IE-BAS) from 1994. 20 papers, included a book chapter, were published by implementing the international joint research under 5 Agreements for Academic Cooperation and Exchange between HIT and IEBAS. Our international joint ...

Comparison of the Tight Rope Technique and Clavicular Hook Plate for the Treatment of Rockwood Type III Acromioclavicular Joint Dislocation.

Science.gov (United States)

Cai, Leyi; Wang, Te; Lu, Di; Hu, Wei; Hong, Jianjun; Chen, Hua

2018-06-01

Acromioclavicular joint dislocation is one of the most common shoulder problems and may lead to instability or degenerative changes. The aim of this study was to compare the clinical outcomes of the Tight Rope system and clavicular hook plate for Rockwood type III acromioclavicular joint dislocation in adults. This was a prospective, randomized study in a hospital setting. From January 2012 to December 2014, 69 patients with type III injury were reviewed. Patients were randomly divided into two groups: Group A was treated using the TightRope system and Group B with the clavicular hook plate. All participants were followed up for 12 months. Clinical outcomes, radiological results and postoperative complications were recorded. The length of incision was significantly shorter in Goup A than that in Group B. The blood loss of surgery was significantly less in the Group A. Significant difference could be found between the two groups regarding the Visual Analogue Scale scores one day after surgery, at the 3 and 12 months follow-up. There were no differences according to the improvement of the Constant-Murley score and the coracoclavicular distance between the groups. The two groups have similar clinical and radiological outcomes. Both treatments could relieve the pain of dislocation, improve the function of Acromioclavicular joint and rectify the coracoclavicular distance measured in plain films. However, the TightRope system exhibited some advantages in terms of length of incision, blood loss of surgery, the pain postoperatively and no need for a second surgery.

Osteochondral lesions in distal tarsal joints of Icelandic horses reveal strong associations between hyaline and calcified cartilage abnormalities.

Science.gov (United States)

Ley, C J; Ekman, S; Hansson, K; Björnsdóttir, S; Boyde, A

2014-03-25

Osteochondral lesions in the joints of the distal tarsal region of young Icelandic horses provide a natural model for the early stages of osteoarthritis (OA) in low-motion joints. We describe and characterise mineralised and non-mineralised osteochondral lesions in left distal tarsal region joint specimens from twenty-two 30 ±1 month-old Icelandic horses. Combinations of confocal scanning light microscopy, backscattered electron scanning electron microscopy (including, importantly, iodine staining) and three-dimensional microcomputed tomography were used on specimens obtained with guidance from clinical imaging. Lesion-types were described and classified into groups according to morphological features. Their locations in the hyaline articular cartilage (HAC), articular calcified cartilage (ACC), subchondral bone (SCB) and the joint margin tissues were identified and their frequency in the joints recorded. Associations and correlations between lesion-types were investigated for centrodistal joints only. In centrodistal joints the lesion-types HAC chondrocyte loss, HAC fibrillation, HAC central chondrocyte clusters, ACC arrest and ACC advance had significant associations and strong correlations. These lesion-types had moderate to high frequency in centrodistal joints but low frequencies in tarsometatarsal and talocalcaneal-centroquartal joints. Joint margin lesion-types had no significant associations with other lesion-types in the centrodistal joints but high frequency in both the centrodistal and tarsometatarsal joints. The frequency of SCB lesion-types in all joints was low. Hypermineralised infill phase lesion-types were detected. Our results emphasise close associations between HAC and ACC lesions in equine centrodistal joints and the importance of ACC lesions in the development of OA in low-motion compression-loaded equine joints.

The joint in psoriatic arthritis.

Science.gov (United States)

Mortezavi, Mahta; Thiele, Ralph; Ritchlin, Christopher

2015-01-01

Psoriatic arthritis (PsA), a chronic inflammatory joint disease associated with psoriasis, is notable for diversity in disease presentation, course and response to treatment. Equally varied are the types of musculoskeletal involvement which include peripheral and axial joint disease, dactylitis and enthesitis. In this review, we focus on the psoriatic joint and discuss pathways that underlie synovial, cartilage and bone inflammation and highlight key histopathologic features. The pivotal inflammatory mechanisms and pathobiology of PsA parallel findings in other forms of spondyloarthritis but are distinct from disease pathways described in rheumatoid synovitis and bone disease. The diagnosis of PsA from both a clinical and imaging perspective is also discussed.

Removal of internal fixation--the effect on patients' complaints: a study of 66 cases of removal of internal fixation after malleolar fractures

DEFF Research Database (Denmark)

Jacobsen, S; Honnens de Lichtenberg, M; Jensen, C M

1994-01-01

To estimate the effect of removal of internal fixation after treatment of malleolar fractures on postoperatively presented complaints, we retrospectively evaluated 66 patients by their records and by personal questionnaires. Of all the patients, 89.4% had one or more complaints. These were...... typically soreness over implant and cicatrix, reduced movement of the ankle joint, and strain-related pain. About 75% of these patients reported improvement after removal. The AO mode of fixation, i.e., typically by lateral semitubular plating and transsyndesmotic screw and a medial screw or pins...... period. We conclude that removal of internal fixation after malleolar fractures is indicated when common types of complaints are presented....

A "New Type of Great Power Relationship" and Governance in the International System of the 21st

Directory of Open Access Journals (Sweden)

Zhongying Pang

2013-12-01

Full Text Available In the early decades of the 21st century, the real world of powers is neither the so-called unipolarity of the United States of America as the sole superpower, nor the trans-Atlantic domination of the joint Western hegemony. Things are no longer that simple. A fundamental fact of the contemporary international system is that several great powers co-exist – a great powers system has emerged. Clearly, the emergence of the great powers system is a major global challenge. Unfortunately, there are still no effective solutions to the challenge posed by the great powers system. However, China’s proposal a “new type of great power relationship” touches on the issue of the management of the 21st century’s great powers system. The concept of a “new type of great power relationship” still needs time to be further developed theoretically. The management of the great powers system could be the main aim of the concept. In order for 2 America to maintain its dominant position, America turns towards Asia. However, this may help consolidate American hegemony for a short time but it cannot manage the great powers system on a long-term basis. This article argues that China’s “new type of great power relationship” can be seen as a foreign policy innovation in managing the great powers system. It notices that, like China’s new proposal, similar arguments on how to deal with the global challenge posed by a great powers system are emerging in Europe and the Asia Pacific.

Arthroscopically Assisted Reconstruction of Acute Acromioclavicular Joint Dislocations: Anatomic AC Ligament Reconstruction With Protective Internal Bracing—The “AC-RecoBridge” Technique

Science.gov (United States)

Izadpanah, Kaywan; Jaeger, Martin; Ogon, Peter; Südkamp, Norbert P.; Maier, Dirk

2015-01-01

An arthroscopically assisted technique for the treatment of acute acromioclavicular joint dislocations is presented. This pathology-based procedure aims to achieve anatomic healing of both the acromioclavicular ligament complex (ACLC) and the coracoclavicular ligaments. First, the acromioclavicular joint is reduced anatomically under macroscopic and radiologic control and temporarily transfixed with a K-wire. A single-channel technique using 2 suture tapes provides secure coracoclavicular stabilization. The key step of the procedure consists of the anatomic repair of the ACLC (“AC-Reco”). Basically, we have observed 4 patterns of injury: clavicular-sided, acromial-sided, oblique, and midportion tears. Direct and/or transosseous ACLC repair is performed accordingly. Then, an X-configured acromioclavicular suture tape cerclage (“AC-Bridge”) is applied under arthroscopic assistance to limit horizontal clavicular translation to a physiological extent. The AC-Bridge follows the principle of internal bracing and protects healing of the ACLC repair. The AC-Bridge is tightened on top of the repair, creating an additional suture-bridge effect and promoting anatomic ACLC healing. We refer to this combined technique of anatomic ACLC repair and protective internal bracing as the “AC-RecoBridge.” A detailed stepwise description of the surgical technique, including indications, technical pearls and pitfalls, and potential complications, is given. PMID:26052493

[Short-term effectiveness of Swanson artificial joint replacement in treating posttraumatic metacarpophalangeal joint stiffness].

Science.gov (United States)

Lu, Hui; Shen, Xiangqian; Xu, Jihua; Huang, Xin; Ye, Po; Wu, Shoucheng

2011-11-01

To investigate the short-term effectiveness of Swanson artificial joint replacement in treating post-traumatic metacarpophalangeal joint stiffness. Between August 2007 and May 2010, 11 cases (13 fingers) of metacarpophalangeal joint stiffness with soft tissue defects underwent Swanson artificial joint replacement. There were 7 males (9 fingers) and 4 females (4 fingers), aged 43 to 65 years with an average of 49 years. The involved fingers included 4 thumbs, 4 index fingers, 3 middle fingers, and 2 ring fingers. The types of injury included open and crush injury in 8 fingers, fracture of the metacarpophalangeal joint in 3 fingers, metacarpophalangeal joint severing in 2 fingers. The time from joint stiffness to hospitalization was 12 to 48 weeks (mean, 24 weeks). The joint activity was (136.82 +/- 28.96) degrees. According to total active motion (TAM) assessment, included good in 1 finger, fair in 6 fingers, and poor in 6 fingers before operation. The activities of daily living were assessed by Sollerman score, which was 45.64 +/- 11.04. The X-ray films and CT scan showed traumatic arthritis of the metacarpophalangeal joint. The incision healed by first intention. All patients were followed up 12 to 34 months (mean, 24.1 months). At last follow-up, the joint activity was (194.64 +/- 28.86) degrees, showing significant difference when compared with preoperative value (t = 25.214, P = 0.000). According to TAM assessment, including excellent in 1 finger, good in 4 fingers, fair in 7 fingers, and poor in 1 finger. The Sollerman score was 67.45 +/- 8.20 postoperatively, showing significant difference when compared with the preoperative score (t = -10.470, P = 0.000). X-ray examination showed no prosthesis fracture, periprosthetic fracture, or joint dislocation occurred at last follow-up. Swanson artificial joint replacement can be applied to treat post-traumatic metacarpophalangeal joint stiffness, which can improve the joint activity and has satisfactory short

Joint made of shape memory alloy

International Nuclear Information System (INIS)

Amano, Kazuo; Enomoto, Kunio

1998-01-01

The present invention provides a joint which is less loosen even if it is used under a circumference undergoing heat cycles such as in a nuclear power plant. Namely, a liner shape has a structure different between the right-to-left, which is different from existent right and left symmetrical shape. A groove is formed on the side of pipeline to be connected, and upon joint connection, the liner is pushed into the groove formed on the pipeline to connect them by the force caused upon transformation of the shape memory alloy. In the joint having such a structure, the clamping force of the joint is less reduced by the effects of heat cycles. Even when the clamping force is reduced by some or other causes, the joint is not dropped off from the pipeline. Even when the joint made of a shape memory alloy of a type using a liner is used as a joint for connecting longitudinal pipelines of a nuclear power plant, the reliability and the safety can be maintained. (I.S.)

A distinct form of spondyloepimetaphyseal dysplasia with joint laxity (SEMDJL)-leptodactylic type: radiological characteristics in seven new patients

Energy Technology Data Exchange (ETDEWEB)

Kim, Ok-Hwa [Ajou University Hospital, Department of Radiology, Suwon (Korea); Cho, Tae-Joon [Seoul National University Children' s Hospital, Department of Orthopaedic Surgery, Seoul (Korea); Song, Hae-Ryong [Korea University Guro Hospital, Department of Othopaedic Surgery, Seoul (Korea); Chung, Chin Youb [Seoul National University Bundang Hospital, Department of Orthopaedic Surgery, Gyeonggi (Korea); Miyagawa, Shin-Ichiro [National Hospital Organization Kure Medical center, Department of Pediatrics, Hiroshima (Japan); Nishimura, Gen [Kiyose Children' s Hospital, Department of Radiology, Tokyo (Japan); Superti-Furga, Andrea [University of Freiburg, Departement of Pediatrics, Freiburg (Germany); Unger, Sheila [Institute of Human Genetics, University of Freiburg, Freiburg (Germany)

2009-08-15

This study presents seven cases of a rare but distinctive form of spondyloepimetaphyseal dysplasia with joint laxity-leptodactylic or Hall type to emphasize the characteristic clinical and radiological findings. A multiinstitutional retrospective review was performed on seven patients. The patient population consisted of one family with an affected mother and two siblings and four unrelated patients; there were one adult, aged 40 years, and six children, ranging in age from 3 to 12 years. The gender ratio of females to males was 5 to 2. We reviewed the clinical data and skeletal surveys and focused on radiographs of the pelvis, knees, hands, and spine. The outstanding clinical features were short stature, midface hypoplasia, and multiple dislocations and/or ligamentous laxity of the large joints, particularly at the knees with a genu valgum or varum deformity. Of seven patients, six patients showed normal intellect but one patient had mild mental retardation. The main radiological features included small, irregular epiphyses, metaphyseal irregularity with vertical striations that was a constant finding at the knees, constricted femoral necks, delayed ossification of the carpal bones, and slender metacarpals. Progressive thoracolumbar scoliosis was evident with aging; however, the vertebral bodies appeared normal in height or mild platyspondyly was noted. In view of the orthopedic management of multiple joint dislocations and ligamentous laxity of the large joints, awareness of this disease entity and diagnostic precision solely based on radiological findings is of importance, particularly as the disorder is currently more common than initially reported. (orig.)

A distinct form of spondyloepimetaphyseal dysplasia with joint laxity (SEMDJL)-leptodactylic type: radiological characteristics in seven new patients

International Nuclear Information System (INIS)

Kim, Ok-Hwa; Cho, Tae-Joon; Song, Hae-Ryong; Chung, Chin Youb; Miyagawa, Shin-Ichiro; Nishimura, Gen; Superti-Furga, Andrea; Unger, Sheila

2009-01-01

This study presents seven cases of a rare but distinctive form of spondyloepimetaphyseal dysplasia with joint laxity-leptodactylic or Hall type to emphasize the characteristic clinical and radiological findings. A multiinstitutional retrospective review was performed on seven patients. The patient population consisted of one family with an affected mother and two siblings and four unrelated patients; there were one adult, aged 40 years, and six children, ranging in age from 3 to 12 years. The gender ratio of females to males was 5 to 2. We reviewed the clinical data and skeletal surveys and focused on radiographs of the pelvis, knees, hands, and spine. The outstanding clinical features were short stature, midface hypoplasia, and multiple dislocations and/or ligamentous laxity of the large joints, particularly at the knees with a genu valgum or varum deformity. Of seven patients, six patients showed normal intellect but one patient had mild mental retardation. The main radiological features included small, irregular epiphyses, metaphyseal irregularity with vertical striations that was a constant finding at the knees, constricted femoral necks, delayed ossification of the carpal bones, and slender metacarpals. Progressive thoracolumbar scoliosis was evident with aging; however, the vertebral bodies appeared normal in height or mild platyspondyly was noted. In view of the orthopedic management of multiple joint dislocations and ligamentous laxity of the large joints, awareness of this disease entity and diagnostic precision solely based on radiological findings is of importance, particularly as the disorder is currently more common than initially reported. (orig.)

Joint Advisory Appeals Board report

CERN Document Server

Lalande, Amanda

2018-01-01

With regard to the internal appeal procedure, Article R VI 1.18 of the Staff Rules and Regulations states that unless the member of the personnel objects, (the) decision and report of the JAAB (Joint Advisory Appeals Board) shall be brought to the attention of the members of the personnel.

[Treatment of pediatric distal femur fractures by external fixator combined with limited internal fixation].

Science.gov (United States)

Wei, Sheng-wang; Shi, Zhan-ying; Hu, Ju-zheng; Wu, Hao

2016-03-01

To discuss the clinical effects of external fixator combined with limited internal fixation in the treatment of pediatric distal femur fractures. From January 2008 to June 2014, 17 children of distal femur fractures were treated by external fixator combined with limited internal fixation. There were 12 males and 5 females, aged from 6 to 13 years old with an average of 10.2 years, ranged in the course of disease from 1 h to 2 d. Preoperative diagnoses were confirmed by X-ray films in all children. There were 11 patients with supracondylar fracture , and 6 patients with intercondylar comminuted fracture. According to AO/ASIF classification, 9 fractures were type A1, 5 cases were type A2,and 3 cases were type C1. The intraoperative and postoperative complications, postoperative radiological examination, lower limbs length and motion of knee joints were observed. Knee joint function was assessed by KSS score. All the patients were followed up from 6 to 38 months with an average of 24.4 months. No nerve or blood vessel injury was found. One case complicated with the external fixation loosening, 2 cases with the infection of pin hole and 3 cases with the leg length discrepancy. Knee joint mobility and length measurement (compared with the contralateral), the average limited inflexion was 10 degrees (0 degrees to 20 degrees), the average limited straight was 4 degrees (0 degrees to 10), the average varus or valgus angle was 3 degrees (0 degrees to 5 degrees). KSS of the injured side was (96.4 +/- 5.0) points at final follow-up, 16 cases got excellent results and 1 good. All fractures obtained healing and no epiphyseal closed early was found. External fixator combined with limited internal fixation has advantages of simple operation, reliable fixation, early functional exercise in treating pediatric distal femurs fractures.

INTERNAL EXTINCTION IN THE SLOAN DIGITAL SKY SURVEY LATE-TYPE GALAXIES

International Nuclear Information System (INIS)

Cho, Jungyeon; Park, Changbom

2009-01-01

We study internal extinction of late-type galaxies in the Sloan Digital Sky Survey. We find that the degree of internal extinction depends on both the concentration index c and K s -band absolute magnitude M K . We give simple fitting functions for internal extinction. In particular, we present analytic formulae giving the extinction-corrected magnitudes from the observed optical parameters. For example, the extinction-corrected r-band absolute magnitude can be obtained by M r,0 =-20.77 +(-1+√(1+4Δ(M r,obs +20.77+4.93Δ)))/2Δ, where Δ = 0.236{1.35(c - 2.48) 2 - 1.14} log(a/b), c = R 90 /R 50 is the the concentration index, and a/b is the isophotal axis ratio of the 25 mag arcsec -2 isophote in the i band. The 1σ error in M r,0 is 0.21 log(a/b). Late-type galaxies with very different inclinations are found to trace almost the same sequence in the (u - r)-M r diagram when our prescriptions for extinction correction are applied. We also find that (u - r) color can be a third independent parameter that determines the degree of internal extinction.

Improving parallel imaging by jointly reconstructing multi-contrast data.

Science.gov (United States)

Bilgic, Berkin; Kim, Tae Hyung; Liao, Congyu; Manhard, Mary Kate; Wald, Lawrence L; Haldar, Justin P; Setsompop, Kawin

2018-08-01

To develop parallel imaging techniques that simultaneously exploit coil sensitivity encoding, image phase prior information, similarities across multiple images, and complementary k-space sampling for highly accelerated data acquisition. We introduce joint virtual coil (JVC)-generalized autocalibrating partially parallel acquisitions (GRAPPA) to jointly reconstruct data acquired with different contrast preparations, and show its application in 2D, 3D, and simultaneous multi-slice (SMS) acquisitions. We extend the joint parallel imaging concept to exploit limited support and smooth phase constraints through Joint (J-) LORAKS formulation. J-LORAKS allows joint parallel imaging from limited autocalibration signal region, as well as permitting partial Fourier sampling and calibrationless reconstruction. We demonstrate highly accelerated 2D balanced steady-state free precession with phase cycling, SMS multi-echo spin echo, 3D multi-echo magnetization-prepared rapid gradient echo, and multi-echo gradient recalled echo acquisitions in vivo. Compared to conventional GRAPPA, proposed joint acquisition/reconstruction techniques provide more than 2-fold reduction in reconstruction error. JVC-GRAPPA takes advantage of additional spatial encoding from phase information and image similarity, and employs different sampling patterns across acquisitions. J-LORAKS achieves a more parsimonious low-rank representation of local k-space by considering multiple images as additional coils. Both approaches provide dramatic improvement in artifact and noise mitigation over conventional single-contrast parallel imaging reconstruction. Magn Reson Med 80:619-632, 2018. © 2018 International Society for Magnetic Resonance in Medicine. © 2018 International Society for Magnetic Resonance in Medicine.

Ehlers-Danlos Syndrome Hypermobility Type

Science.gov (United States)

EHLERS-DANLOS SYNDROME HYPERMOBILITY TYPE Ehlers-Danlos syndrome hypermobility type is a connective tissue disorder that mostly affects the bones and joints. People with this condition have loose joints ...

78 FR 58352 - Joint Industry Plan; Notice of Filing of Amendment No. 30 to the Joint Self-Regulatory...

Science.gov (United States)

2013-09-23

... Collection, Consolidation and Dissemination of Quotation and Transaction Information for Nasdaq-Listed... Exchange, Inc., EDGX Exchange, Inc., Financial Industry Regulatory Authority, Inc., International... ``Committee'') \\3\\ of the Joint Self-Regulatory Organization Plan Governing the Collection, Consolidation, and...

The application of magnetic resonance imaging in temporomandibular joint pathology

International Nuclear Information System (INIS)

Ehmedov, E.T.; Qahramanov, E.T.

2007-01-01

The diseases and damages of temporomandibular joint have compleceted diagnostic unlike other bone-joint pathologies. In 2005 for the first time in history it was implemented the magnetic resonance imaging in diagnostics of patients with with temporomandibular joints pathology. The current researches are in place till today. Being the golden standart the application of magnetic resonance tomography has a great role in differential diagnostics of the chronic arthritis, sclerosanse, deformanse arthrosis and arthrosis with internal derancement. This method guaranteed the correct valuation of the bone, disc and muscle structures of the joint and therefore brought full clearance into the problem

The strength research of the adhesive joints of sheet structures ...

African Journals Online (AJOL)

The research results of stress-strained condition of constructional sheet materials are given in the article. The strength dependence on type, configuration and sizes of adhesive joints is analyzed. The research of the strength dependence was made on the samples from bakelite plywood with the main types of adhesive joints ...

International survey of primary and revision total knee replacement

NARCIS (Netherlands)

Kurtz, Steven M.; Ong, Kevin L.; Lau, Edmund; Widmer, Marcel; Maravic, Milka; Gomez-Barrena, Enrique; de Pina, Maria de Fatima; Manno, Valerio; Torre, Marina; Walter, William L.; de Steiger, Richard; Geesink, Rudolph G. T.; Peltola, Mikko; Roeder, Christoph

2011-01-01

Total knee arthroplasty (TKA) is currently the international standard of care for treating degenerative and rheumatologic knee joint disease, as well as certain knee joint fractures. We sought to answer the following three research questions: (1) What is the international variance in primary and

Osteochondral lesions in distal tarsal joints of Icelandic horses reveal strong associations between hyaline and calcified cartilage abnormalities

Directory of Open Access Journals (Sweden)

CJ Ley

2014-03-01

Full Text Available Osteochondral lesions in the joints of the distal tarsal region of young Icelandic horses provide a natural model for the early stages of osteoarthritis (OA in low-motion joints. We describe and characterise mineralised and non-mineralised osteochondral lesions in left distal tarsal region joint specimens from twenty-two 30 ±1 month-old Icelandic horses. Combinations of confocal scanning light microscopy, backscattered electron scanning electron microscopy (including, importantly, iodine staining and three-dimensional microcomputed tomography were used on specimens obtained with guidance from clinical imaging. Lesion-types were described and classified into groups according to morphological features. Their locations in the hyaline articular cartilage (HAC, articular calcified cartilage (ACC, subchondral bone (SCB and the joint margin tissues were identified and their frequency in the joints recorded. Associations and correlations between lesion-types were investigated for centrodistal joints only. In centrodistal joints the lesion-types HAC chondrocyte loss, HAC fibrillation, HAC central chondrocyte clusters, ACC arrest and ACC advance had significant associations and strong correlations. These lesion-types had moderate to high frequency in centrodistal joints but low frequencies in tarsometatarsal and talocalcaneal-centroquartal joints. Joint margin lesion-types had no significant associations with other lesion-types in the centrodistal joints but high frequency in both the centrodistal and tarsometatarsal joints. The frequency of SCB lesion-types in all joints was low. Hypermineralised infill phase lesion-types were detected. Our results emphasise close associations between HAC and ACC lesions in equine centrodistal joints and the importance of ACC lesions in the development of OA in low-motion compression-loaded equine joints.

Finite element analysis of elasto-plastic tee joints

International Nuclear Information System (INIS)

Powell, G.H.

1974-09-01

The theory and computational procedures used in the computer program B169TJ/EP for the analysis of elasto-plastic tee joints are described, and detailed user's guide is presented. The program is particularly applicable to joints conforming to the ANSI B16.9 Manufacturing Standard, but can also be applied to other joint geometries. The joint may be loaded by internal pressure and by arbitrary combinations of applied forces and moments at the ends of the branch and run pipes, and the loading sequence may be arbitrary. The joint material is assumed to yield according to the von Mises criterion, and to exhibit either linear kinematic hardening or nonlinear isotropic hardening after yield. The program makes use of the finite element and mesh generation procedures previously applied in the elastic stress analysis program B16.9TJ/ SA, with minor modifications. (U.S.)

Undenatured type II collagen (UC-II®) for joint support: a randomized, double-blind, placebo-controlled study in healthy volunteers.

Science.gov (United States)

Lugo, James P; Saiyed, Zainulabedin M; Lau, Francis C; Molina, Jhanna Pamela L; Pakdaman, Michael N; Shamie, Arya Nick; Udani, Jay K

2013-10-24

UC-II contains a patented form of undenatured type II collagen derived from chicken sternum. Previous preclinical and clinical studies support the safety and efficacy of UC-II in modulating joint discomfort in osteoarthritis and rheumatoid arthritis. The purpose of this study was to assess the efficacy and tolerability of UC-II in moderating joint function and joint pain due to strenuous exercise in healthy subjects. This randomized, double-blind, placebo-controlled study was conducted in healthy subjects who had no prior history of arthritic disease or joint pain at rest but experienced joint discomfort with physical activity. Fifty-five subjects who reported knee pain after participating in a standardized stepmill performance test were randomized to receive placebo (n = 28) or the UC-II (40 mg daily, n = 27) product for 120 days. Joint function was assessed by changes in degree of knee flexion and knee extension as well as measuring the time to experiencing and recovering from joint pain following strenuous stepmill exertion. After 120 days of supplementation, subjects in the UC-II group exhibited a statistically significant improvement in average knee extension compared to placebo (81.0 ± 1.3º vs 74.0 ± 2.2º; p = 0.011) and to baseline (81.0 ± 1.3º vs 73.2 ± 1.9º; p = 0.002). The UC-II cohort also demonstrated a statistically significant change in average knee extension at day 90 (78.8 ± 1.9º vs 73.2 ± 1.9º; p = 0.045) versus baseline. No significant change in knee extension was observed in the placebo group at any time. It was also noted that the UC-II group exercised longer before experiencing any initial joint discomfort at day 120 (2.8 ± 0.5 min, p = 0.019), compared to baseline (1.4 ± 0.2 min). By contrast, no significant changes were seen in the placebo group. No product related adverse events were observed during the study. At study conclusion, five individuals in the UC-II cohort

Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

Simultaneous of Mid Third Clavicle Fracture and Type 3 Acromioclavicular Joint Dislocation; A Case Report

Directory of Open Access Journals (Sweden)

Saeed Solooki

2014-03-01

Full Text Available Simultaneous mid third clavicle fracture and acromioclavicular joint dislocation is a rare combination injury, as a result of high-energy trauma. We report a patient with a middle third clavicle fracture and ipsilateral grade three-acromioclavicular joint dislocation, which is a rare combination. The patient wanted to get back to work as soon as possible, so the fracture was fixed with reconstruction plate after open reduction and plate contouring; and acromioclavicular joint dislocation was reduced and fixed with two full threaded cancellous screws. One screw was inserted through the plate to the coracoid process. Clinical and radiographic finding revealed complete union of clavicle fracture and anatomical reduction of acromioclavicular joint with pain free full joint range of motion one year after operation.

Simultaneous of Mid Third Clavicle Fracture and Type 3 Acromioclavicular Joint Dislocation; A Case Report

Directory of Open Access Journals (Sweden)

Saeed Solooki

2014-03-01

Full Text Available   Simultaneous mid third clavicle fracture and acromioclavicular joint dislocation is a rare combination injury, as a result of high-energy trauma. We report a patient with a middle third clavicle fracture and ipsilateral grade three-acromioclavicular joint dislocation, which is a rare combination. The patient wanted to get back to work as soon as possible, so the fracture was fixed with reconstruction plate after open reduction and plate contouring; and acromioclavicular joint dislocation was reduced and fixed with two full threaded cancellous screws. One screw was inserted through the plate to the coracoid process. Clinical and radiographic finding revealed complete union of clavicle fracture and anatomical reduction of acromioclavicular joint with pain free full joint range of motion one year after operation.

[Case-control study on effects of external fixation combined with limited internal fixation for the treatment of Pilon fractures of Rüedi-Allgower type III].

Science.gov (United States)

Duan, Da-Peng; You, Wu-Lin; Ji, Le; Zhang, Yong-Tao; Dang, Xiao-Qian; Wang, Kun-Zheng

2014-01-01

To analyze the effects of three surgical operations in the treatment of Pilon fracture of Rüedi-Allgower type III, and put forward the best therapeutic method. The clinical data of 33 patients with Pilon fracture who received surgical operations (plaster immobilization group, 10 cases; distal tibia anatomical plate group, 11 cases; external fixation with limited internal fixation group, 12 cases) from October 2009 to January 2012 were analyzed. There were 5 males and 5 females, ranging in age from 24 to 61 years in the plaster immobilization group. There were 7 males and 4 females, ranging in age from 21 to 64 years in the distal tibia anatomical plate group. There were 7 males and 5 females, ranging in age from 23 to 67 years in the external fixation with limited internal fixation group. The Ankle X-ray of Pilon fracture after operation, ankle score, early and late complications were collected. Bourne system was used to evaluate ankle joint function. After 8 months to 3 years follow-up, it was found that three kinds of treatment had significant differences in the outcomes and complications (P external fixation with limited internal fixation group got the best results. The number of anatomic reduction cases in the external fixation with limited internal fixation group (7 cases) and the distal tibia anatomical plate group (8 cases) was more than the plaster immobilization group (2 cases). According to the ankle score, 8 patients got an excellent result, 3 good and 1 poor in the limited internal fixation group ,which was better than those of distal tibia anatomical plate group (5 excellent, 4 good and 2 poor) and the plaster immobilization group (3 excellent, 4 good and 3 poor). The number of early and late complications in the external fixation with limited internal fixation group was more than those in the plaster immobilization group and the distal tibia anatomical plate group (Pexternal fixation with limited internal fixation in the treatment of Pilon fracture

Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome Hypermobility Type: a revision of the rehabilitative approach

Directory of Open Access Journals (Sweden)

Claudia Celletti

2016-09-01

Full Text Available Joint hypermobility syndrome (JHS and Ehlers-Danlos syndrome, hypermobility type (EDS-HT are two clinically overlapping heritable connective tissue disorders strongly associating with pain, fatigue and other secondary aspects. No specific treatment exist for this syndrome and rehabilitation play a role in the management of these patients. The aim of this paper is to evaluate what are the evidence in literature about rehabilitation. Research was done using database PUBMED and consist in a revision of the studies published in the last 15 years. All studies agree to the beneficial role of the rehabilitative treatment and physical therapy but it’s necessary to add more further studies to establish a high quality, evidence-based physical therapy for this specific population.

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

Main benefits from 30 years of joint projects in nuclear safety

International Nuclear Information System (INIS)

Thadani, Ashok; Teschendorff, Victor; Vitanza, Carlo; Hrehor, Miroslav

2012-01-01

One of the major achievements of the OECD Nuclear Energy Agency (NEA) is the knowledge it has helped to generate through the organisation of joint international research projects. Such projects, primarily in the areas of nuclear safety and radioactive waste management, enable interested countries, on a cost-sharing basis, to pursue research or the sharing of data with respect to particular areas or issues. Over the years, more than 30 joint projects have been conducted with wide participation of member countries. The purpose of this report is to describe the achievements of the OECD/NEA joint projects on nuclear safety research that have been carried out over the past three decades, with a particular focus on thermal-hydraulics, fuel behaviour and severe accidents. It shows that the resolution of specific safety issues in these areas has greatly benefited from the joint projects' activities and results. It also highlights the added value of international co-operation for maintaining unique experimental infrastructure, preserving skills and generating new knowledge

International Research Chairs Initiative | IDRC - International ...

International Development Research Centre (IDRC) Digital Library (Canada)

The International Research Chairs Initiative (IRCI) is a seven-year, CA$8 million research program that pairs top research talent from universities in Canada with their counterparts in developing countries to address key ... The results of this joint effort: world-class discoveries and healthier, wealthier, fairer societies.

Types of internal facilitation activities in hospitals implementing evidence-based interventions.

Science.gov (United States)

Baloh, Jure; Zhu, Xi; Ward, Marcia M

2017-01-25

Implementation models, frameworks, and theories recognize the importance of activities that facilitate implementation success. However, little is known about internal facilitation activities that hospital personnel engage in during implementation efforts. The aim of the study was to examine internal facilitation activities at 10 critical access hospitals in rural Iowa during their implementation of TeamSTEPPS, a patient safety intervention, and to identify characteristics that distinguish different types of facilitation activities. We followed 10 critical access hospitals for 2 years after the onset of implementation, conducting quarterly interviews with key informants. On the basis of the transcripts from the first two quarters, a coding template was developed using inductive analyses. The template was then applied deductively to code all interview transcripts. Using comparative analysis, we examined the characteristics that distinguish between the facilitation types. We identified four types of facilitation activities-Leadership, Buy-in, Customization, and Accountability. Individuals and teams engaged in different types of facilitation activities, both in a planned and an ad hoc manner. These activities targeted at both people and practices and exhibited varying temporal patterns (start and peak time). There are four types of facilitation activities that hospitals engage in while implementing evidence-based practices, offering a parsimonious way to characterize facilitation activities. New theoretical and empirical research opportunities are discussed. Understanding the types of facilitation activities and their distinguishing characteristics can assist managers in planning and executing implementations of evidence-based interventions.

Microstructure development of welding joints in high Cr ferritic steels

Energy Technology Data Exchange (ETDEWEB)

Kubushiro, Keiji; Takahashi, Satoshi; Morishima, Keiko [IHI Corporation (Japan). Research Lab.

2010-07-01

Creep failure in high Cr ferritic steels welding joints are Type IV failure. Type IV-failure was ruptured in fine grained region of heat affected zone, microstructure and phase transformation process at welding in fine grained region were very important to clarify. Microstructure difference of heat affected zone was investigated in Gr.91, Gr.92, Gr.122 welding joint. The fraction of 60 degree block boundary, packet boundary, random boundary (including prior gamma boundary) length was compared in three ferritic steels by EBSP(Electron Backscatter Diffraction Pattern) analysis. HAZ was almost fully martensite phase in Gr.122 weld joint. On the other hand, HAZ in Gr.91 welding joint were some equiaxial grain and martensite structure. (orig.)

Jet Joint Undertaking

International Nuclear Information System (INIS)

Keen, B.E.; O'Hara, G.W.; Pollard, I.E.

1988-07-01

The paper presents the Jet Joint Undertaking annual report 1987. A description is given of the JET and Euratom and International Fusion Programmes. The technical status of JET is outlined, including the development and improvements made to the system in 1987. The results of JET Operation in 1987 are described within the areas of: density effects, temperature improvements, energy confinement studies and other material effects. The contents also contain a summary of the future programme of JET. (U.K.)

Carbon and prospective: international colloquium jointly organized by the prospective modeling chair and ETSAP

International Nuclear Information System (INIS)

Maizi, N.; Hourcade, J.Ch.; Selosse, S.

2009-01-01

The inauguration of the prospective modeling chair in favour of sustainable development is the result of the joint effort of several schools, organizations and companies, in particular: Mines ParisTech, Ponts ParisTech, Agro ParisTech, the higher education and research pole of ParisTech, the Ecole des Ponts foundation, the mineral, mining and metallurgic industries foundation (FI3M), with the partnership of Ademe, EdF, Renault, Schneider Electric and Total. The main goal of this chair is to perpetuate modeling tools with sustainable development stakes. The scientific program and the expertise of this chair are based on the joint and complementary experience of its two co-founder research teams in the domain of long-term prospective of energy, economy and environment-related questions: the applied mathematics centre (CMA - Mines ParisTech) and the international centre of environment and sustainable development research (CIRED). An inaugural colloquium was organized at the occasion of the launching of this chair. During round tables, representatives of the different intervening parties explained the stakes of this huge project and their expectations, in particular from the scientific, economical and societal point of view. A workshop on the topic 'carbon and prospective' followed the round tables. Six presentations were given about the following topics: energy policy scenarios for 2050 (Moncomble, J.E.), the shadow price of carbon (Chambolle T.), mitigation targets and carbon values: insights from TIMES-FR (Assoumou E.), climate protection and infrastructures (Sassi O.), China's energy and carbon options (Wenying C.), EU 20-20 policy implications on the energy system of Germany - an analysis with TIMES PanEU (Blesl M.). This book gathers the proceedings of both parts of this colloquium, the debates during the round tables (in French) and the presentations given during the workshop (in English). (J.S.)

Fatigue strength evaluation of friction stir welded aluminium joints using the nominal and notch stress concepts

International Nuclear Information System (INIS)

Barsoum, Z.; Khurshid, M.; Barsoum, I.

2012-01-01

Highlights: ► Fatigue testing and evaluation of friction stir welded butt and overlap joints. ► Evaluation based on nominal and effective notch stress concept. ► Comparison with different design recommendations and codes. ► Higher fatigue strength and SN-slopes is observed. ► New fatigue design recommendations proposed for FSW joints. -- Abstract: In this study the fatigue strength is investigated for Friction Stir Welded (FSW) overlap and butt welded joints in different thicknesses based on nominal and effective notch stress concepts. The fatigue test results are compared with fatigue strength recommendations according to EN 1999-1-3 and International Institute of Welding (IIW). The results are also compared with available published data and Finite Element Analysis (FEA) is carried out to investigate the effect of plate thickness and nugget size on the fatigue strength of overlap joints. 3–3 mm butt welded joints shows the highest fatigue strength in comparison with 3–5 mm butt welded and overlap joints. Slopes of the SN-curves for two different joint types differ from the slope recommended by IIW. A specific failure trend is observed in overlap FSW joints. However, the slopes of the SN-curves are in close agreement with slopes found in EN 1999-1-3. The slopes of various published results and test results presented in this study are in good agreement with each other. The suggested fatigue design curves for the nominal and effective notch stress concept have a higher slope than given for fusion welds by IIW.

Heat Resistance of Glued Finger Joints in Spruce Wood Constructions

Directory of Open Access Journals (Sweden)

Martin Sviták

2014-10-01

Full Text Available The heat resistance of glued spruce wood was evaluated for different joint types and adhesives. Bending strength, modulus of elasticity, and also fracture evaluation were investigated on glued spruce samples made by the finger-jointed principle. Finger-jointed samples were glued with polyurethane (PUR and melamine-urea-formaldehyde (MUF adhesives. Heat loading was realized at temperatures 60, 80, and 110 °C and compared with wood with 20 °C. A static bending test with four-point flexural test was used. Elevated temperature and adhesive type had an important influence on the bending strength. On the other hand, adhesive type had a significant influence on the modulus of elasticity, but elevated temperature had no substantial influence.

Critical temperature gradient length signatures in heat wave propagation across internal transport barriers in the Joint European Torus

International Nuclear Information System (INIS)

Casati, Alessandro; Mantica, P.; Eester, D. van; Hawkes, N.; De Vries, P.; Imbeaux, F.; Joffrin, E.; Marinoni, A.; Ryter, F.; Salmi, A.; Tala, T.

2007-01-01

New results on electron heat wave propagation using ion cyclotron resonance heating power modulation in the Joint European Torus (JET) [P. H. Rebut et al., Nucl. Fusion 25, 1011 (1985)] plasmas characterized by internal transport barriers (ITBs) are presented. The heat wave generated outside the ITB, and traveling across it, always experiences a strong damping in the ITB layer, demonstrating a low level of transport and loss of stiffness. In some cases, however, the heat wave is strongly inflated in the region just outside the ITB, showing features of convective-like behavior. In other cases, a second maximum in the perturbation amplitude is generated close to the ITB foot. Such peculiar types of behavior can be explained on the basis of the existence of a critical temperature gradient length for the onset of turbulent transport. Convective-like features appear close to the threshold (i.e., just outside the ITB foot) when the value of the threshold is sufficiently high, with a good match with the theoretical predictions for the trapped electron mode threshold. The appearance of a second maximum is due to the oscillation of the temperature profile across the threshold in the case of a weak ITB. Simulations with an empirical critical gradient length model and with the theory based GLF23 [R. E. Waltz et al., Phys. Plasmas, 4, 2482 (1997)] model are presented. The difference with respect to previous results of cold pulse propagation across JET ITBs is also discussed

Development of Displacement Gages Exposed to Solid Rocket Motor Internal Environments

Science.gov (United States)

Bolton, D. E.; Cook, D. J.

2003-01-01

The Space Shuttle Reusable Solid Rocket Motor (RSRM) has three non-vented segment-to-segment case field joints. These joints use an interference fit J-joint that is bonded at assembly with a Pressure Sensitive Adhesive (PSA) inboard of redundant O-ring seals. Full-scale motor and sub-scale test article experience has shown that the ability to preclude gas leakage past the J-joint is a function of PSA type, joint moisture from pre-assembly humidity exposure, and the magnitude of joint displacement during motor operation. To more accurately determine the axial displacements at the J-joints, two thermally durable displacement gages (one mechanical and one electrical) were designed and developed. The mechanical displacement gage concept was generated first as a non-electrical, self-contained gage to capture the maximum magnitude of the J-joint motion. When it became feasible, the electrical displacement gage concept was generated second as a real-time linear displacement gage. Both of these gages were refined in development testing that included hot internal solid rocket motor environments and simulated vibration environments. As a result of this gage development effort, joint motions have been measured in static fired RSRM J-joints where intentional venting was produced (Flight Support Motor #8, FSM-8) and nominal non-vented behavior occurred (FSM-9 and FSM-10). This data gives new insight into the nominal characteristics of the three case J-joint positions (forward, center and aft) and characteristics of some case J-joints that became vented during motor operation. The data supports previous structural model predictions. These gages will also be useful in evaluating J-joint motion differences in a five-segment Space Shuttle solid rocket motor.

Temporomandibular joint examination reviewed

Directory of Open Access Journals (Sweden)

L. Guarda Nardini

2011-09-01

Full Text Available The temporo-mandibular joint (TMJ it’s a joint closely related to the skull base, the spine, and the jaws; all these anatomical structures must be taken in consideration when evaluating pain involving the tmj. In order to detect patients affected by pathology or dysfunctions of the tmj, physical examination is of great value in orienting the diagnosis. Inspection must consider the symmetry of the body, the dental status and the type of occlusion. Palpation is a way to assess contractiont involving the muscles of the masticatory system and of the neck. Auscultation, based on articular noise provides means to determine whether we are dealing with degeneration of the joint or a dislocation of the intrarticular disc. In order to confirm the diagnosis obtained with the clinical evaluation, it’s useful to perform imaging techniques as opt, tomography and TC of the tmj and electromyokineosiography – index of the mandibular functionality and of the muscles status. MRI and dynamic MRI are among the non invasive exams which give the greatest amount of information, regarding the disc position and the joint degeneration. Arthroscopy is an invasive technique that allows early diagnosis of degeneration and is helpful to reveal early inflammatory processes of the joint.

Imaging of the temporomandibular joint: An update

Institute of Scientific and Technical Information of China (English)

Asim; K; Bag; Santhosh; Gaddikeri; Aparna; Singhal; Simms; Hardin; Benson; D; Tran; Josue; A; Medina; Joel; K; Curé

2014-01-01

Imaging of the temporomandibular joint(TMJ) is continuously evolving with advancement of imaging technologies. Many different imaging modalities are currently used to evaluate the TMJ. Magnetic resonance imaging is commonly used for evaluation of the TMJ due to its superior contrast resolution and its ability to acquire dynamic imaging for demonstration of the functionality of the joint. Computed tomography and ultrasound imaging have specific indication in imaging of the TMJ. This article focuses on state of the art imaging of the temporomandibular joint. Relevant normal anatomy and biomechanics of movement of the TMJ are discussed for better understanding of many TMJ pathologies. Imaging of internal derangements is discussed in detail. Different arthropathies and commontumors are also discussed in this article.

[Analysis on the long-term effects of modified double endobutton technique in the treatment of Tossy type III acromioclavicular joint dislocations].

Science.gov (United States)

Yan, Rui-Jian; Lu, Jian-Wei; Zhang, Chun

2014-01-01

To investigate the long-term clinical effects of modified double Endobutton technique for the treatment of acromioclavicular joint dislocations of Tossy type III. A retrospective study was done in 42 patients with acromioclavicular joint dislocations of Tossy type III treated with modified double Endobutton technique from December 2008 to December 2010. There were 24 males and 18 females, ranging in age from 21 to 56 years old (averaged, 32.5 years old). All the patients were treated with open reduction, coracoclavicular ligament reconstruction using double Endobutton technique, and repair of acromioclavicular ligament. The Karlsson system was used to evaluate therapeutic effects. The distance from coracoid to clavicle was measured to evaluate reduction loss. All the patients were followed up, and the duration ranged from 2.0 to 3.2 years (averaged,2.4 years). According to Karlsson system, 32 patients got an A degree and 10 patients got a B degree at three months post-operatively; 26 patients got an A degree and 16 patients got a B degree at the latest follow-up; 6 patients got an A degree at 3 months after operation lowered to B degree at the latest follow-up. The coracoid-clavicle distance increased from (26.91 +/- 0.91) mm at 3 months after operation to (27.41 +/- 1.10) mm at the latest follow-up. Te patients treated with over-reduction during operation or with heavy physical labour work after operation had obvious widened coracoid-clavicle distance. Bone absorption was found around the plate in most cases, mainly in the clavicular side. Treatment for acromioclavicular joint dislocations of Tossy type III with modified double Endobutton technique has satisfactory early clinical results. But with time passing, loss of reduction and bone absorption around the plate could be observed, and clinical outcomes of some cases downgrade during the long-term follow-up.

Limited Reliability of Radiographic Assessment of Sacroiliac Joints in Patients with Suspected Early Spondyloarthritis

DEFF Research Database (Denmark)

Christiansen, Alice Ashouri; Hendricks, Oliver; Kuettel, Dorota

2017-01-01

Objective. To determine the reproducibility of evaluation of sacroiliac joint (SIJ) radiographs among readers with varying levels of experience, and to identify potential drivers of disagreement in classification among 5 predefined radiographic lesion types. Methods. The study sample consisted of...... of 104 consecutive patients aged 18-40 with low back pain ≥ 3 months of duration who met the Assessment of SpondyloArthritis international Society (ASAS) definition for a positive SIJ magnetic resonance image, or were HLA-B27-positive and had ≥ 1 spondyloarthritis (SpA)-related clinical...

Psychopathological manifestations of joint hypermobility and joint hypermobility syndrome/ Ehlers-Danlos syndrome, hypermobility type: The link between connective tissue and psychological distress revised.

Science.gov (United States)

Sinibaldi, Lorenzo; Ursini, Gianluca; Castori, Marco

2015-03-01

Psychological distress is a known feature of generalized joint hypermobility (gJHM), as well as of its most common syndromic presentation, namely Ehlers-Danlos syndrome, hypermobility type (a.k.a. joint hypermobility syndrome - JHS/EDS-HT), and significantly contributes to the quality of life of affected individuals. Most published articles dealt with the link between gJHM (or JHS/EDS-HT) and anxiety-related conditions, and a novel generation of studies is emerging aimed at investigating the psychopathologic background of such an association. In this paper, literature review was carried out with a semi-systematic approach spanning the entire spectrum of psychopathological findings in gJHM and JHS/EDS-HT. Interestingly, in addition to the confirmation of a tight link between anxiety and gJHM, preliminary connections with depression, attention deficit (and hyperactivity) disorder, autism spectrum disorders, and obsessive-compulsive personality disorder were also found. Few papers investigated the relationship with schizophrenia with contrasting results. The mind-body connections hypothesized on the basis of available data were discussed with focus on somatotype, presumed psychopathology, and involvement of the extracellular matrix in the central nervous system. The hypothesis of positive Beighton score and alteration of interoceptive/proprioceptive/body awareness as possible endophenotypes in families with symptomatic gJHM or JHS/EDS-HT is also suggested. Concluding remarks addressed the implications of the psychopathological features of gJHM and JHS/EDS-HT in clinical practice. © 2015 Wiley Periodicals, Inc.

Design Oriented Model for the Assessment of T-Shaped Beam-Column Joints in Reinforced Concrete Frames

Directory of Open Access Journals (Sweden)

Antonio Bossio

2017-12-01

Full Text Available Beam-column joints represent very important elements of reinforced concrete (RC structures. In fact, beams and columns, at the boundary, generate internal forces acting on concrete core and on reinforcement bars with a very high gradient. To fully understand the seismic performances and the failure modes of T-shaped beam-column joints (external corner-positioned in RC structures, a simplified analytical model of joint behaviour is proposed and theoretical simulations have been performed. The model is based on the solution of a system of equilibrium equations of cracked joint portions designed to evaluate internal stresses at different values of column shear forces. The main aim of the proposed model is to identify the strength hierarchy. Limit values of different internal stresses allow us to detect the occurrence of different failure modes (namely the failure of the cracked joint, the bond failure of passing through bars, and the flexural/shear failures of columns or beams associated with column shear forces; the smaller one represents the capacity of the joint. The present work, focusing on T-shaped joints, could represent a useful tool for designers to quantify the performance of new structures or of existing ones. In fact, such a tool allows us to push an initial undesired failure mode to a more appropriate one to be evaluated. Finally, some experimental results of tests available in literature are reported, analysed, and compared to the predictions of the proposed model (by means of a worked example and of some international codes. The outcomes confirm that failure modes and corresponding joint capacities require an analytical model, like the proposed one, to be accurately predicted.

Computed tomography of the knee joint

International Nuclear Information System (INIS)

Jang, Byung Won; Kwon, Jung Hyeok; Park, Sung Hak; Kim, Tae Hun; Park, In Kyu; Kim, Yong Joo; Kang, Duk Sik; Kwon, Sae Hong

1986-01-01

Diagnosis of knee joint pathology has been mainly dependent on clinical manifestations and invasive procedures such as arthrography and arthroscopy etc. However, these procedures are invasive. Arthroscopy is performed under general anesthesia. Recently, with development of high resolution CT with thin slices and multiplanar reconstructions capability, CT could be used to verify the internal structures of knee joint in noninvasive or less invasive way. From June to December 1985, authors have experienced 19 cases of the knee joint CT. Among them, 13 cases were operated and confirmed. We concluded as follows. 1. The diagnostic accuracy of the knee CT was 100% in lateral meniscal tearing, 92.3% in medial mensical tearing, 92.3% in detachment of lateral collateral ligament, 92.3% in medial collateral ligament, 100% in tearing of cruciate ligaments. 2. CT could be considered as a primary diagnostic procedure in the knee pathology rather than more invasive arthroscopy or arthrography. 3. For the accurate diagnosis of knee joint pathology, CT, which can obtain thin slies, high resolution, multiplanar reconstructions, is indispensable.

The Effect of Tool Profiles on Mechanical Properties of Friction Stir Welded Al5052 T-Joints.

Science.gov (United States)

Kim, Byeong-Jin; Bang, Hee-Seon; Bang, Han-Sur

2018-03-01

Al5052 T butt joints with two skins (5 mm) and one stringer (3 mm) has been successfully welded by friction stir welding (FSW). Notably, this paper has been investigated the effect of tool shape on welded formation mechanism and mechanical properties. The used shapes of tool pin are two types which are cylinder (type 1) and frustum (type 2). Dimension on two types of tool pin shape is respectively pin length of 4.7 mm and pin diameter of frustum type of top (5 mm) and bottom (3 mm). The results of experiment show that inner defects in FSWed T-joints increase significantly in accordance with traverse speed. The maximum tensile strength of welded joint fabricated using type 1 is equivalent to 85% that of the base metal, which is approximately 10% higher than that of type 2. Because welded joint of type 1 has more smoothly plastic flow in comparison with type 2. Consequently, the results show that type 1 is better appropriate for friction stir welded Al5052 T butt joints than type 2.

Temporomandibular joint (TMJ) pain revisited with dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI)

International Nuclear Information System (INIS)

Tasali, N.; Cubuk, R.; Aricak, M.; Ozarar, M.; Saydam, B.; Nur, H.; Tuncbilek, N.

2012-01-01

Purpose: We aimed to assess the contrast enhancement patterns of the retrodiscal tissue with dynamic contrast-enhanced MR imaging (DCE-MRI) with respect to different temporomandibular joint disc pathologies. Additionally, we questioned the relationship between the temporomandibular joint (TMJ) pain and the contrast enhancement pattern of the retrodiscal tissue regardless of the TMJ disc position. Materials and methods: 52 joints of 26 patients (4 males and 22 females) who have pain in at least at one of their TMJ were included in this study. For the qualitative analysis, the joints were divided into four groups in terms of their disc positions: normal (1), partially displaced with or without reduction (2), totally dislocated with reduction (3) and totally dislocated without reduction (4). Besides, two different joint groups were constituted, namely the painful group and painless group according to the clinical findings without taking the TMJ disc positions into account. Quantitative analyses were made by means of measuring signal intensity ratios (SI) ratio at the retrodiscal tissue (from internal side and external side of the each joint) using DCE-MRI and these measurements were analyzed with paired samples t test to define the difference between the measurements. At the second stage, the time-dependent arithmetical mean values of the SI ratios were calculated for each joint group and significant differences between the groups were questioned using analysis of variance (ANOVA) test. Besides, painful and painless groups which were classified on the basis of the clinical data were compared according to the mean SI ratios found for each joint and the significant differences between these two groups were assessed by means of Student's T test. The results were assessed in 95% confidence interval where the significance level was p < 0.05. Results: A significant difference was observed between the internal and external contrast enhancement of the joints with partial

Inelastic behavior of a dissimilar-metal-welded pipe transition joint: comparison of experimental measurements and analytical prediction

International Nuclear Information System (INIS)

Yang, T.M.; Dalcher, A.W.

1979-06-01

The subject study involved the prediction and observed behavior of a dissimilar metal pipe joint made from 2 1/4 Cr-1Mo steel welded to Type 316 austenitic stainless steel using a nickel-base filler metal, ERNiCr-3. A two-dimensional axi-symmetric finite element model was employed in the analysis, with certain assumptions made relative to the initial stress state of the joint. Internal pressure and thermal loadings which simulated the test conditions experienced by the joint, were used as inputs. Uni-axial stress-strain relationships and creep equations were applied to the multi-axial stress state through the concept of effective stress and equivalent strain. The analysis indicated that the loading history during the preparatory period (before acutal service) has a significant effect on the behavior of the transition joint in its early service life. The magnitudes of the stresses created at the vicinity of the dissimilar metal interfaces, mainly due to the differences in thermal expansions of the metals, are sufficient to yield the metals, and fast thermal down transients during service will induce more yielding of the metals before shakedown occurs. Calculated plastic ratchetting and creep responses of the joint metals were compared with ORNL strain measurements of the test joint. Very good agreement was shown to exist between the predictions and measurements

The sacroiliac joint: anatomy, physiology and clinical significance.

Science.gov (United States)

Forst, Stacy L; Wheeler, Michael T; Fortin, Joseph D; Vilensky, Joel A

2006-01-01

The sacroiliac joint (SIJ) is a putative source of low back pain. The objective of this article is to provide clinicians with a concise review of SIJ structure and function, diagnostic indicators of SIJ-mediated pain, and therapeutic considerations. The SIJ is a true diarthrodial joint with unique characteristics not typically found in other diarthrodial joints. The joint differs with others in that it has fibrocartilage in addition to hyaline cartilage, there is discontinuity of the posterior capsule, and articular surfaces have many ridges and depressions. The sacroiliac joint is well innervated. Histological analysis of the sacroiliac joint has verified the presence of nerve fibers within the joint capsule and adjoining ligaments. It has been variously described that the sacroiliac joint receives its innervation from the ventral rami of L4 and L5, the superior gluteal nerve, and the dorsal rami of L5, S1, and S2, or that it is almost exclusively derived from the sacral dorsal rami. Even though the sacroiliac joint is a known putative source of low back and lower extremity pain, there are few findings that are pathognomonic of sacroiliac joint pain. The controlled diagnostic blocks utilizing the International Association for the Study of Pain (IASP) criteria demonstrated the prevalence of pain of sacroiliac joint origin in 19% to 30% of the patients suspected to have sacroiliac joint pain. Conservative management includes manual medicine techniques, pelvic stabilization exercises to allow dynamic postural control, and muscle balancing of the trunk and lower extremities. Interventional treatments include sacroiliac joint, intra-articular joint injections, radiofrequency neurotomy, prolotherapy, cryotherapy, and surgical treatment. The evidence for intra-articular injections and radiofrequency neurotomy has been shown to be limited in managing sacroiliac joint pain.

Stiffness Coefficients of Mortise and Tenon Joints used on Wooden Window Profiles

Directory of Open Access Journals (Sweden)

Milan Podlena

2016-04-01

Full Text Available Samples of corner joints of wooden rectangular windows, with widths of 78 and 92 mm, were used to determine the stiffness of tenon and mortise joints. Two series of samples were loaded statically in the angular plane of compression and tension, so that the bending moment could be derived. The objective of the experiment was to determine the existing correlations between the stiffness in maximum strength and the stiffness in the elastic area for both types of tests. After strength tests were carried out, the annual ring width of the samples was measured to determine whether this factor affects the stiffness of the joints. The results showed that there was a relatively strong correlation between the stiffness in the elastic area and the maximum load. A two-factor analysis of variance confirmed that the type of load did not affect the stiffness of the joint, but the type of joint (width does significantly affect the stiffness. Therefore, the width of annual rings was positively correlated with the stiffness of the joints.

Changes on magnetic resonance tomography in the knee joints of marathon runners: a 10-year longitudinal study

International Nuclear Information System (INIS)

Krampla, Wolfgang W.; Newrkla, Stephan P.; Hruby, Walter F.; Kroener, Andreas H.

2008-01-01

The aim of the study was to evaluate long-term damage in the internal structures of the knee joints of recreational long-distance runners. Ten years after their participation in a baseline study concerning their knee joints, seven long-distance runners and one who had given up long-distance running were invited to participate in a repeat magnetic resonance imaging (MRI) investigation. The same evaluation criteria and the same technical equipment were used, and the results of the two investigations were compared. No adverse long-term consequences were observed in six of the seven active runners, regardless of pre-existing damage at the baseline investigation. In one case the arthrotic changes were progressive in nature. The person who had given up running presented with severe deterioration of the internal structures of the knee joint. Non-physiological maximal loads secondary to the marathon race do not cause any permanent damage in the internal structures of the knee joint in individuals without significant pre-existing damage. A disposition for premature arthrosis was not registered in the population investigated. A protective value of long distance running on the internal structures of the knee joint is discussed. (orig.)

Changes on magnetic resonance tomography in the knee joints of marathon runners: a 10-year longitudinal study

Energy Technology Data Exchange (ETDEWEB)

Krampla, Wolfgang W.; Newrkla, Stephan P.; Hruby, Walter F. [Danube Hospital, Radiology Department, Vienna (Austria); Kroener, Andreas H. [Danube Hospital, Department of Orthopedic Surgery, Vienna (Austria)

2008-07-15

The aim of the study was to evaluate long-term damage in the internal structures of the knee joints of recreational long-distance runners. Ten years after their participation in a baseline study concerning their knee joints, seven long-distance runners and one who had given up long-distance running were invited to participate in a repeat magnetic resonance imaging (MRI) investigation. The same evaluation criteria and the same technical equipment were used, and the results of the two investigations were compared. No adverse long-term consequences were observed in six of the seven active runners, regardless of pre-existing damage at the baseline investigation. In one case the arthrotic changes were progressive in nature. The person who had given up running presented with severe deterioration of the internal structures of the knee joint. Non-physiological maximal loads secondary to the marathon race do not cause any permanent damage in the internal structures of the knee joint in individuals without significant pre-existing damage. A disposition for premature arthrosis was not registered in the population investigated. A protective value of long distance running on the internal structures of the knee joint is discussed. (orig.)

Three types of communication on internal social media:

DEFF Research Database (Denmark)

Madsen, Vibeke Thøis

The aim of this paper is to explore to what extend internal social media introduces a new kind of participatory communication in organizations. The paper is based on two explorative studies: A multiple case study in ten Danish organizations and a single case study in a Danish bank. Based on the t....... Different levels of communication might be reached in different types of organizations, and it is only when coworkers perceive a license to critique that organizations will actually develop participatory communication that has the ability to move the organization....

Dynamic 3 T MRI of temporomandibular joint in diagnosing a stuck disk

Directory of Open Access Journals (Sweden)

J Sureka

2012-01-01

Full Text Available Magnetic resonance imaging (MRI is the imaging modality of choice in the evaluation of internal derangement of the temporomandibular joint (TMJ. Dynamic MRI including the open and close mouth views in sagittal plane determine the exact position of articular disk and thus help to evaluate the joint for internal derangement. We also highlight the role of dynamic MRI of TMJ in diagnosis of stuck disk in a 17-year-old male who presented with symptoms of pain and difficulty in opening the mouth.

International Joint Conference CISIS’15 and ICEUTE’15

CERN Document Server

Baruque, Bruno; Sedano, Javier; Quintián, Héctor; Corchado, Emilio

2015-01-01

This volume of Advances in Intelligent and Soft Computing contains accepted papers presented at the 8th International Conference on Computational Intelligence in Security for Information Systems (CISIS 2015) and the 6th International Conference on EUropean Transnational Education (ICEUTE 2015). These conferences were held in the beautiful and historic city of Burgos (Spain), in June 2015. The aim of the 8th CISIS conference is to offer a meeting opportunity for academic and industry-related researchers belonging to the various, vast communities of Computational Intelligence, Information Security, and Data Mining. The need for intelligent, flexible behaviour by large, complex systems, especially in mission-critical domains, is intended to be the catalyst and the aggregation stimulus for the overall event. After a through peer-review process, the CISIS 2015 International Program Committee selected 43 papers, written by authors from 16 different countries. In the case of 6th ICEUTE conference, the International ...

Joint Support and Efficient Offshore Investment: Market and Transmission Connection Barriers and Solutions

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten; Kitzing, Lena; Klinge Jacobsen, Henrik

2012-01-01

Different support schemes are applied for the promotion of renewable energy sources in EU Member States. Current EU legislation opens opportunities for international cooperation to achieve national renewable targets more efficiently, either by statistical transfers, joint projects or joint support...

[Inferior hemiarthroplasty of the temporo-mandibular joint with articulated condylar prosthesis type Stryker].

Science.gov (United States)

Bucur, A; Dincă, O; Totan, C; Ghită, V

2007-01-01

The optimal reconstruction of the mandible and of the temporo-mandibular joint after mandibular hemi-resection with disarticulation is still controversial in literature. This paperwork presents our experience on four cases in the reconstruction of the mandible together with the inferior arthroplasty of the temporo-mandibular joint, after the resection of extended benign tumors of the mandible, based on fibular free vascularized grafts having attached a Stryker titanium condylar prosthesis reconstructing the inferior segment of the temporo-mandibular joint. Our results for the this technique were excellent, with a functional rehabilitation very close to normal. After reviewing the various techniques and their arguments in literature, with accent on the TMJ reconstruction, we consider this method to be optimal for the reconstruction of mandibular defects in patients with neoplastic conditions.

26 CFR 1.401(a)-11 - Qualified joint and survivor annuities.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 5 2010-04-01 2010-04-01 false Qualified joint and survivor annuities. 1.401(a...)-11 Qualified joint and survivor annuities. (a) General rule—(1) Required provisions. A trust, to...), which is a part of a plan providing for the payment of benefits in any form of a life annuity (as...

[Clinical observation on the effect of joint mobilization in treating elderly patients after distal radius fractures operation].

Science.gov (United States)

Jia, Xue-Feng; Cai, Hong-Xin; Lin, Ge-Sheng; Fang, Ji-Shi; Wang, Yong; Wu, Zhi-Yong; Tu, Xu-Hui

2017-07-25

To investigate the effect of joint mobilization on postoperative wrist joint function, pain and grip strength for elderly patients with distal radius fracture. From January 2015 to June 2016, a total of 67 elderly patients with distal radius fracture were randomly divided into routine exercise group and joint mobilization group. Among them, 37 patients in the routine exercise group underwent conventional distal radius fracture postoperative joint function exercise regimen, including 16 males and 21 females with a mean age of (67.8±3.2) years old ranging from 60 to 72 years old;the injured side was dominant in 23 cases and non-dominant in 14 cases;injury mechanism was fall in 26 cases, traffic accident in 11 cases; for AO type, 6 cases were type B3, 18 cases were type C1, 7 cases were type C2, 6 cases was type C3. Other 30 patients in the joint mobilization group underwent joint mobilization on the basis of the routine exercise group including 14 males and 16 females with a mean age of (67.1±4.0) years old ranging from 61 to 74 years old; the injured side was dominant in 21 cases and non-dominant in 9 cases;injury mechanism was fall in 25 cases, traffic accident in 5 cases;for AO type, 8 cases were type B3, 13 cases were type C1, 6 cases were type C2, 9 cases were type C3. The wrist joint activity, Gartland-Werley wrist joint function score, VAS pain score and grip strength were observed at 3 months afrer treatment. After 3 months' treatment, the VAS in the routine exercise group was higher than that of the joint mobilization group ( P joint mobilization group was higher than that in routine exercise group( P joint mobilization group( P joint mobilization group had no significant difference ( P >0.05). In the comparison of each item of Gartland-Werley, there was no significant difference between two groups in residual deformity and complication( P >0.05); the average score of subjective score, objective score and total score in routine exercise group were

2014 ICSA/KISS Joint Applied Statistics Symposium

CERN Document Server

Liu, Mengling; Luo, Xiaolong

2016-01-01

The papers in this volume represent the most timely and advanced contributions to the 2014 Joint Applied Statistics Symposium of the International Chinese Statistical Association (ICSA) and the Korean International Statistical Society (KISS), held in Portland, Oregon. The contributions cover new developments in statistical modeling and clinical research: including model development, model checking, and innovative clinical trial design and analysis. Each paper was peer-reviewed by at least two referees and also by an editor. The conference was attended by over 400 participants from academia, industry, and government agencies around the world, including from North America, Asia, and Europe. It offered 3 keynote speeches, 7 short courses, 76 parallel scientific sessions, student paper sessions, and social events. The most timely and advanced contributions from the joint 2014 ICSA/KISS Applied Statistics Symposium All papers feature original, peer-reviewed content Coverage consists of new developments in statisti...

Joint effects of hypertension, smoking, dyslipidemia and obesity and angiotensin-converting enzyme DD genotype on albuminuria in Taiwanese patients with type 2 diabetes mellitus.

Science.gov (United States)

Tseng, Chin-Hsiao; Tseng, Ching-Ping; Chong, Choon-Khim

2010-05-01

We investigated the individual and joint effects of hypertension, smoking, dyslipidemia, and obesity and angiotensin-converting enzyme (ACE) DD genotype on albuminuria in Taiwanese type 2 diabetic patients. ACE genotypes were determined in 519 (287 men and 232 women) patients aged 58.5 (SD: 9.0) years. Among them, 240 had albuminuria (urinary albumin-to-creatinine ratio > or =30 microg/mg). Logistic regression was used to evaluate the individual and joint effects of risk factors and DD classified by two-by-four table. The adjusted odds ratios were significant for hypertension, smoking and obesity but not for DD and dyslipidemia in models evaluating individual effects. However, while analyzing the joint effects of DD and hypertension, smoking, dyslipidemia and obesity, the respective adjusted odds ratios were 3.253 (1.261-8.391), 3.016 (1.086-8.376), 2.385 (1.010-5.630) and 2.508 (1.117-5.631). Hypertension, smoking, dyslipidemia and obesity jointly play an important role with DD genotype in mediating albuminuria. 2010 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Joint thesaurus Part I (A-L) + II (M-Z)[International Nuclear Information System. Energy Technology Data Exchange

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-04-15

This is the second revision of the ETDE/INIS Joint Thesaurus, including all updates up to September 2006. It contains 21 147 valid descriptors and 9 114 forbidden terms. The Joint Thesaurus contains the controlled terminology for indexing all information within the subject scopes of the International Nuclear Information System (INIS) and the Energy Technology Data Exchange (ETDE). The terminology is intended for use in subject descriptions for input or retrieval of information in these systems. The thesaurus is a terminological control device used in translating from the natural language of documents, indexers or users into a more constrained system language It is also a controlled and dynamic vocabulary of semantically and generically related terms which covers a specific domain of knowledge. The basic terminology in this thesaurus goes back to the 1969 edition of the EURATOM Thesaurus. The structure subsequently given to that terminology was the result of a systematic study performed by INIS subject specialists. Further expansion of the thesaurus terminology was done by ETDE to incorporate information on all forms of energy. The ETDE/INIS Joint Thesaurus is the result of continued editing, carried out in parallel to the processing of the INIS and ETDE databases. The domain of knowledge covered by the Joint Thesaurus includes physics (in particular, plasma physics, atomic and molecular physics, and especially nuclear and high-energy physics), chemistry, materials science, earth sciences, radiation biology, radioisotope effects and kinetics, applied life sciences, radiology and nuclear medicine, isotope and radiation source technology, radiation protection, radiation applications, engineering, instrumentation, fossil fuels, synthetic fuels, renewable energy sources, advanced energy systems, fission and fusion reactor technology, safeguards and inspection, waste management, environmental aspects of the production and consumption of energy from nuclear and non

Improvement of Internal Audit Planning Method through Application of Risk Card by the Indices of Value-Based Management System of Joint-Stock Company

OpenAIRE

Oleksandr Smetanko

2014-01-01

The Article deals with issues of improving methods of planning and carrying out internal audit in conditions of risk-oriented approach to audit according to the indices of value-based management system - VBM (Value Based Management) using the risk card (risk matrix). A risk card (risk matrix) method has been disclosed taking into account risk level of each of the key factors influencing joint-stock company value rates. Recommendations have been given and abstract of working document has been ...

The neuromuscular differential diagnosis of joint hypermobility.

Science.gov (United States)

Donkervoort, S; Bonnemann, C G; Loeys, B; Jungbluth, H; Voermans, N C

2015-03-01

Joint hypermobility is the defining feature of various inherited connective tissue disorders such as Marfan syndrome and various types of Ehlers-Danlos syndrome and these will generally be the first conditions to be considered by geneticists and pediatricians in the differential diagnosis of a patient presenting with such findings. However, several congenital and adult-onset inherited myopathies also present with joint hypermobility in the context of often only mild-to-moderate muscle weakness and should, therefore, be included in the differential diagnosis of joint hypermobility. In fact, on the molecular level disorders within both groups represent different ends of the same spectrum of inherited extracellular matrix (ECM) disorders. In this review we will summarize the measures of joint hypermobility, illustrate molecular mechanisms these groups of disorders have in common, and subsequently discuss the clinical features of: 1) the most common connective tissue disorders with myopathic or other neuromuscular features: Ehlers-Danlos syndrome, Marfan syndrome and Loeys-Dietz syndrome; 2) myopathy and connective tissue overlap disorders (muscle extracellular matrix (ECM) disorders), including collagen VI related dystrophies and FKBP14 related kyphoscoliotic type of Ehlers-Danlos syndrome; and 3) various (congenital) myopathies with prominent joint hypermobility including RYR1- and SEPN1-related myopathy. The aim of this review is to assist clinical geneticists and other clinicians with recognition of these disorders. © 2015 Wiley Periodicals, Inc.

The modelling of two DOF joints controlled by elastic inner ties

Directory of Open Access Journals (Sweden)

Ożóg Dominik

2017-01-01

Full Text Available This paper considers the mathematical model of two types of joints that can be used to connect the arms of two robots. The first of them is a simple revolute joint with one degree of freedom and the second is a universal joint with two degrees of freedom. Each of them is controlled using elastic ties that run in the joints and are connected to the inside of the arm joints. This paper describes a study of kinematics, dynamics properties and Extended Denavit-Hartenberg Notation parameters mentioned joints.

45 CFR 2516.820 - What types of internal evaluation activities are required of programs?

Science.gov (United States)

2010-10-01

... required to: (a) Continuously assess management effectiveness, the quality of services provided, and the satisfaction of both participants and service recipients. Internal evaluations should seek frequent feedback... 45 Public Welfare 4 2010-10-01 2010-10-01 false What types of internal evaluation activities are...

Force-Sensing Actuator with a Compliant Flexure-Type Joint for a Robotic Manipulator

Directory of Open Access Journals (Sweden)

Mathieu Grossard

2015-12-01

Full Text Available This paper deals with the mechatronic design of a novel self-sensing motor-to-joint transmission to be used for the actuation of robotic dexterous manipulators. Backdrivability, mechanical simplicity and efficient flexure joint structures are key concepts that have guided the mechanical design rationale to provide the actuator with force sensing capabilities. Indeed, a self-sensing characteristic is achieved by the specific design of high-resolution cable-driven actuators based on a DC motor, a ball-screw and a monolithic compliant anti-rotation system together with a novel flexure pivot providing a frictionless mechanical structure. That novel compliant pivot with a large angular range and a small center shift has been conceived of to provide the inter-phalangeal rotational degree of freedom of the fingers’ joints to be used for integration in a multi-fingered robotic gripper. Simultaneously, it helps to remove friction at the joint level of the mechanism. Experimental tests carried out on a prototype show an accurate matching between the model and the real behavior. Overall, this mechatronic design contributes to the improvement of the manipulation skills of robotic grippers, thanks to the combination of high performance mechanics, high sensitivity to external forces and compliance control capability.

Joint attention, social cognition and recognition memory in adults

Directory of Open Access Journals (Sweden)

Kwanguk eKim

2012-06-01

Full Text Available The early emerging capacity for Joint Attention, or socially coordinated visual attention, is thought to be integral to the development of social-cognition in childhood. Recent studies have also begun to suggest that joint attention affects adult cognition as well, but methodological limitations hamper research on this topic. To address this issue we developed a novel virtual reality (VR paradigm that integrates eye-tracking and virtual avatar technology to measure two types of joint attention in adults, Initiating Joint Attention (IJA and Responding to Joint Attention (RJA. Distinguishing these types of joint attention in research is important because they are thought to reflect unique, as well as common constellations of processes involved in human social-cognition and social learning. We tested the validity of the differentiation of IJA and RJA in our paradigm in two studies of picture recognition memory in undergraduate students. Study 1 indicated that young adults correctly identified more pictures they had previously viewed in an IJA condition (67% than in a RJA (58% condition, η2 = .57. Study 2 controlled for IJA and RJA stimulus viewing time differences, and replicated the findings of Study 1. The implications of these results for the validity of the paradigm and research on the affects of joint attention on adult social-cognition are discussed.

Hip and knee joint loading during vertical jumping and push jerking.

Science.gov (United States)

Cleather, Daniel J; Goodwin, Jon E; Bull, Anthony M J

2013-01-01

The internal joint contact forces experienced at the lower limb have been frequently studied in activities of daily living and rehabilitation activities. In contrast, the forces experienced during more dynamic activities are not well understood, and those studies that do exist suggest very high degrees of joint loading. In this study a biomechanical model of the right lower limb was used to calculate the internal joint forces experienced by the lower limb during vertical jumping, landing and push jerking (an explosive exercise derived from the sport of Olympic weightlifting), with a particular emphasis on the forces experienced by the knee. The knee experienced mean peak loadings of 2.4-4.6×body weight at the patellofemoral joint, 6.9-9.0×body weight at the tibiofemoral joint, 0.3-1.4×body weight anterior tibial shear and 1.0-3.1×body weight posterior tibial shear. The hip experienced a mean peak loading of 5.5-8.4×body weight and the ankle 8.9-10.0×body weight. The magnitudes of the total (resultant) joint contact forces at the patellofemoral joint, tibiofemoral joint and hip are greater than those reported in activities of daily living and less dynamic rehabilitation exercises. The information in this study is of importance for medical professionals, coaches and biomedical researchers in improving the understanding of acute and chronic injuries, understanding the performance of prosthetic implants and materials, evaluating the appropriateness of jumping and weightlifting for patient populations and informing the training programmes of healthy populations. Copyright © 2012 Elsevier Ltd. All rights reserved.

26 CFR 11.401(a)-11 - Qualified joint and survivor annuities.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 14 2010-04-01 2010-04-01 false Qualified joint and survivor annuities. 11.401... SECURITY ACT OF 1974 § 11.401(a)-11 Qualified joint and survivor annuities. (a) In general—(1) General rule... annuity (i.e., an annuity requiring survival of the participant or his spouse as a condition for payment...

Safety and Efficacy of NEXT-II®, a Novel Water-Soluble, Undenatured Type II Collagen inHealthy Human SubjectsSuffering from Occasional Knee Joint Pain

Directory of Open Access Journals (Sweden)

Orie Yoshinari

2015-07-01

Full Text Available Background: Oral administration of a novel water-soluble undenatured type II collagen (NEXT-II® has been demonstrated to ameliorate the signs and symptoms of rheumatoid arthritis (RA in animal models. In the present investigation, we conducted a pilot study to examine the efficacy and safety of NEXT-II® in borderline subjects defined as healthy and non-diseased state, but with potential risks in knee joint health. Method: We employed Western Ontario McMaster Index (WOMAC score and Visual Analog Scale (VAS scores to assess the extent of improvement in the knee joints in these volunteers following supplementation of 40 mg NEXT-II® (10 mg as undenatured type II collagen over a period of 12 weeks. Result: The results demonstrated that NEXT-II® treatment significantly reduced WOMAC and VAS scores compared to subjects at baseline. Specifically, in the evaluation using VAS, the borderline subjects at resting, walking, and going up and down the stairs revealed significant improvement when compared to the baseline. Conclusion: The results of the studies demonstrated that NEXT-II® might be an ingredient which is safe and effective in the application of dietary supplement in ameliorating joint pain and symptoms of the borderline subjects without any adverse events.

MR findings of the temporomandibular joint with crepitus

International Nuclear Information System (INIS)

Sano, Tsukasa; Yamamoto, Mika; Yamaga, Takayoshi; Takahashi, Koji; Masuda, Saeko; Tagaya, Atsuko; Michi, Ken-ichi; Okano, Tomohiro

1997-01-01

Crepitus is an important sign for diagnosis of arthrosis of the temporomandibular joint (TMJ). The presence of crepitus can be evaluated by the listening test previously proposed by our group. However, TMJ can be diagnosed by MR imaging showing the disc position and related findings including bony changes and joint effusion. This study investigated the relationship between the presence of crepitus and pathology of the joint. Fourteen joints with crepitus diagnosed by the listening test were examined in this study. TMJ was categorized into four types based on findings on double spin echo MR images. The results were as follows: Of fourteen joints with crepitus, five (36%) were showed as normal superior disc position. The remaining 9 joints (64%) were diagnosed with disc displacement, of which, 6 showed reduction, one was without reduction and 2 without reduction were associated with arthrosis. Statistical analysis using the data obtained here and other data showed that the joints with crepitus tended to show disk displacement. There was no significant difference between the degree of certainty about the presence of the crepitus and the distribution of joint pathology. Joint effusion was observed only in the joints with displacement. These results indicated that TMJ with crepitus is associated with varied joint pathology. (author)

MR findings of the temporomandibular joint with crepitus

Energy Technology Data Exchange (ETDEWEB)

Sano, Tsukasa; Yamamoto, Mika; Yamaga, Takayoshi; Takahashi, Koji; Masuda, Saeko; Tagaya, Atsuko; Michi, Ken-ichi; Okano, Tomohiro [Showa Univ., Tokyo (Japan). School of Dentistry

1997-06-01

Crepitus is an important sign for diagnosis of arthrosis of the temporomandibular joint (TMJ). The presence of crepitus can be evaluated by the listening test previously proposed by our group. However, TMJ can be diagnosed by MR imaging showing the disc position and related findings including bony changes and joint effusion. This study investigated the relationship between the presence of crepitus and pathology of the joint. Fourteen joints with crepitus diagnosed by the listening test were examined in this study. TMJ was categorized into four types based on findings on double spin echo MR images. The results were as follows: Of fourteen joints with crepitus, five (36%) were showed as normal superior disc position. The remaining 9 joints (64%) were diagnosed with disc displacement, of which, 6 showed reduction, one was without reduction and 2 without reduction were associated with arthrosis. Statistical analysis using the data obtained here and other data showed that the joints with crepitus tended to show disk displacement. There was no significant difference between the degree of certainty about the presence of the crepitus and the distribution of joint pathology. Joint effusion was observed only in the joints with displacement. These results indicated that TMJ with crepitus is associated with varied joint pathology. (author)

Gd-DTPA (gadolinium diethylenetriamine pentaacetic acid) in MR imaging of the internal derangement of temporomandibular joint

International Nuclear Information System (INIS)

Tange, Kazuhisa; Mihara, Manabu; Maeda, Sanae; Iwata, Hiroyuki; Ito, Noboru; Fukaya, Masahiko.

1990-01-01

Magnetic resonance (MR) imaging was performed in five internal derangement of temporomandibular joint (TMJ) patients, before and after intravenous administration of gadolinium-DTPA (Gd-DTPA) as a contrast agent. MR imaging was performed with a 0.5 tesla unit (VISTA MR; PICKER INTERNATIONAL) using a surface coil. We obtained multiple 5 mm sagital images with open and closed jaw positions. Precontrast proton density images were obtained with a repetition time (TR) of 1,000 msec and an echo time (TE) of 40 msec (TR/TE=1,000/40). Gd-DTPA was administered intravenously in a dose of 0.2 ml per kilogram of body weight. After the injection, postcontrast T1 weighted images (500/20) or postcontrast proton density images (1,000/40) were obtained. In the postcontrast T1 weighted images, the soft tissue surrounding the articular disk was enhanced and it provided helpful information for assessing the disk position. On the other hand, there was no effect of the contrast agent in the postcontrast proton density images. None of the patients experienced allergic reactions or other side effects. Gd-DTPA appeared to be a safe and effective contrast agent for MR imaging with T1 weighted images. However, compared with our usual imaging of the TMJ, the imaging did not indicate greater MR sensitivity for detecting the articular disk by means of Gd-DTPA enhancement. (author)

Joint Attention, Social-Cognition, and Recognition Memory in Adults

OpenAIRE

Kim, Kwanguk; Mundy, Peter

2012-01-01

The early emerging capacity for Joint Attention, or socially coordinated visual attention, is thought to be integral to the development of social-cognition in childhood. Recent studies have also begun to suggest that joint attention affects adult cognition as well, but methodological limitations hamper research on this topic. To address this issue we developed a novel virtual reality (VR) paradigm that integrates eye-tracking and virtual avatar technology to measure two types of joint attenti...

The effect of controlled shot peening on fusion welded joints

International Nuclear Information System (INIS)

Lah, Nur Azida Che; Ali, Aidy; Ismail, Napsiah; Chai, Lim Poon; Mohamed, Abdul Aziz

2010-01-01

This work examines the effect of controlled shot peening (CSP) treatment on the fatigue strength of an ASTM A516 grade 70 carbon steel welded joint. Metallurgical modifications, hardness, elemental compositions, and internal discontinuities, such as porosity, inclusions, lack of penetration, and undercut found in treated and untreated fusion welded joints, were characterized. The fatigue results of as-welded and peened skimmed joints were compared. It was observed that the effect of the CSP and skimming processes improved the fatigue life of the fusion weld by 50% on MMA-welded, 63% on MIG-welded, and 60% on TIG-welded samples.

Incudomalleal joint formation: the roles of apoptosis, migration and downregulation

Directory of Open Access Journals (Sweden)

Matalova Eva

2007-12-01

Full Text Available Abstract Background The middle ear of mammals is composed of three endochondrial ossicles, the stapes, incus and malleus. Joints link the malleus to the incus and the incus to the stapes. In the mouse the first arch derived malleus and incus are formed from a single Sox9 and Type II collagen expressing condensation that later subdivides to give rise to two separate ossicles. In contrast the stapes forms from a separate condensation derived from the second branchial arch. Fusion of the malleus and incus is observed in a number of human syndromes and results in conductive hearing loss. Understanding how this joint forms during normal development is thus an important step in furthering our understanding of such defects. Results We show that the developing incudomalleal joint is characterised by a lack of proliferation and discrete areas of apoptosis. Apoptosis has been suggested to aid in the removal of pre-cartilaginous cells from the joint region, allowing for the physical separation of the cartilaginous elements, however, we show that joint initiation is unaffected by blocking apoptosis. There is also no evidence of cell migration out of the presumptive joint region, as observed by labelling of joint and ossicle cells in culture. Using Type II collagen lacZ reporter mice, however, it is evident that cells in the presumptive joint region remain in place and downregulate cartilage markers. Conclusion The malleus and incus first appear as a single united condensation expressing early cartilage markers. The incudomalleal joint region forms by cells in the presumptive joint region switching off cartilage markers and turning on joint markers. Failure in this process may result in fusion of this joint, as observed in human syndromes such as Branchio-Oto-Renal Syndrome or Treacher Collins Syndrome.

An analysis of a joint shear model for jointed media with orthogonal joint sets

International Nuclear Information System (INIS)

Koteras, J.R.

1991-10-01

This report describes a joint shear model used in conjunction with a computational model for jointed media with orthogonal joint sets. The joint shear model allows nonlinear behavior for both joint sets. Because nonlinear behavior is allowed for both joint sets, a great many cases must be considered to fully describe the joint shear behavior of the jointed medium. An extensive set of equations is required to describe the joint shear stress and slip displacements that can occur for all the various cases. This report examines possible methods for simplifying this set of equations so that the model can be implemented efficiently form a computational standpoint. The shear model must be examined carefully to obtain a computationally efficient implementation that does not lead to numerical problems. The application to fractures in rock is discussed. 5 refs., 4 figs

Joint enterprise: righting a wrong turn?

OpenAIRE

Jacobson, Jessica; Kirby, Amy; Hunter, Gillian

2016-01-01

This report presents the findings of an exploratory study of joint enterprise, undertaken by the Institute for Criminal Policy Research, in partnership with the Prison Reform Trust, and within funding from the Nuffield Foundation. Joint enterprise is a doctrine of the criminal law which permits multiple defendants to be convicted of the same criminal offence even where they had different types or levels of involvement. It has been the source of great controversy in recent years.\\ud \\ud The st...

Long-term load–deformation behaviour of timber–concrete joints

NARCIS (Netherlands)

Van de Kuilen, J.W.G.; Dias, A.M.P.G.

2011-01-01

This paper discusses the long-term mechanical behaviour of timber-to-concrete joints made with dowel-type fasteners. Despite the influence that the long-term behaviour of joints has on the mechanical behaviour of a timber–concrete structure and consequently on its design, there is still a lack of

Environmental influence on the usage of adhesive single lap joints in nuclear industry applications

International Nuclear Information System (INIS)

Amorim, Felipe do C.; Reis, João M.L. dos; Souza, João F.B. de; Costa, Gilberto T. de P.; Moura, Jorge C. de; Universidade Federal Fluminense; Comissao Nacional de Energia Nuclear

2017-01-01

Despite of some polymeric compounds vulnerability to different types of radiation, high polymer, as epoxy adhesives, had prospered in the nuclear industry because their mechanical properties to high doses of ionizing radiation is maintained. Because of this, epoxy adhesives are widely used in nuclear applications: nuclear power plants, aerospace components, radioactive sealed sources to medicine, radioactive waste immobilization. In the present work, the performance of a diglycidyl ether of bisphenol ether A (DGEBA) was analyzed. Tensile tests of adhesive single lap joints bonded with epoxy were performed. The environmental effect of ultraviolet (UV) exposure was observed in the mechanical reaction of PolyAnchor 4100 HT. In particular, maximum load decreases slightly in aggressive environment. It is possible to conclude the material is proper to use in internal and external areas, mainly due to the easy application when compared to welded joints with similar strength. The easy application reduces the workers exposure time to ionizing radiation. (author)

Environmental influence on the usage of adhesive single lap joints in nuclear industry applications

Energy Technology Data Exchange (ETDEWEB)

Amorim, Felipe do C.; Reis, João M.L. dos; Souza, João F.B. de; Costa, Gilberto T. de P.; Moura, Jorge C. de, E-mail: felipe.amorim@cefet-rj.br, E-mail: jreis@id.uff.br, E-mail: joaofellipe@id.uff.br, E-mail: gilberto.costa@cnen.gov.br, E-mail: jcmoura@cnen.gov.br [Centro Federal de Educação Tecnológica Celso Suckow da Fonseca (CEFET-RJ), Itaguai, RJ (Brazil). Departamento de Engenharia Mecanica; Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Laboratorio de Mecania Teorica e Aplicada; Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Divisão de Controle de Rejeitos e Transporte de Materiais Radioativos

2017-07-01

Despite of some polymeric compounds vulnerability to different types of radiation, high polymer, as epoxy adhesives, had prospered in the nuclear industry because their mechanical properties to high doses of ionizing radiation is maintained. Because of this, epoxy adhesives are widely used in nuclear applications: nuclear power plants, aerospace components, radioactive sealed sources to medicine, radioactive waste immobilization. In the present work, the performance of a diglycidyl ether of bisphenol ether A (DGEBA) was analyzed. Tensile tests of adhesive single lap joints bonded with epoxy were performed. The environmental effect of ultraviolet (UV) exposure was observed in the mechanical reaction of PolyAnchor 4100 HT. In particular, maximum load decreases slightly in aggressive environment. It is possible to conclude the material is proper to use in internal and external areas, mainly due to the easy application when compared to welded joints with similar strength. The easy application reduces the workers exposure time to ionizing radiation. (author)

Diagnostic imaging of sacroiliac joints and the spine in the course of spondyloarthropathies

Science.gov (United States)

Sudoł-Szopinska, Iwona; Urbanik, Andrzej

2013-01-01

Summary Spondyloarthropathies belong to a group of rheumatic diseases, in which inflammatory changes affect mainly the sacroiliac joints, spine, peripheral joints, tendon, ligaments and capsule attachments (entheses). This group includes 6 entities: ankylosing spondylitis, arthritis associated with inflammatory bowel disease, reactive arthritis, undifferentiated spondyloarthropathy, psoriatic arthritis and juvenile spondyloarthropathy. In 2009, ASAS (Assessment in SpondyloArthritis international Society) association, published classification criteria for spondyloarthropathies, which propose standardization of clinical-diagnostic approach in the case of sacroiliitis, spondylitis and arthritis. Radiological diagnosis of inflammatory changes of sacroiliac joints is based on a 4 step radiographic grading method from 1966. According to modified New York criteria, the diagnosis of ankylosing spondylitis is made based on the presence of advanced lesions, sacroiliitis of at least 2 grade bilaterally or 3–4 unilaterally. In case of other types of spondyloarthropathies diagnosis is made based on presence of at least grade 1 changes. In MRI, active inflammation of sacroiliac joints is indicated by the presence of subchondral bone marrow edema, synovitis, bursitis, or enthesitis. ASAS discusses only the classic form of axial spondyloarthropathies, which is ankylosing spondylitis. To quantify radiological inflammatory changes in the course of the disease, Stoke Ankylosing spondylitis classification Spinal Score (SASSS) is recommended. The signs of inflammation and scarrying of the spinal cord in the course of ankylosing spondylitis, present in MRI include: bone marrow edema, sclerosis, fat metaplasia, formation of syndesmophytes, and ankylosis. PMID:23807884

Diagnostic imaging of sacroiliac joints and the spine in the course of spondyloarthropathies

International Nuclear Information System (INIS)

Sudoł-Szopinska, Iwona; Urbanik, Andrzej

2013-01-01

Spondyloarthropathies belong to a group of rheumatic diseases, in which inflammatory changes affect mainly the sacroiliac joints, spine, peripheral joints, tendon, ligaments and capsule attachments (entheses). This group includes 6 entities: ankylosing spondylitis, arthritis associated with inflammatory bowel disease, reactive arthritis, undifferentiated spondyloarthropathy, psoriatic arthritis and juvenile spondyloarthropathy. In 2009, ASAS (Assessment in SpondyloArthritis international Society) association, published classification criteria for spondyloarthropathies, which propose standardization of clinical-diagnostic approach in the case of sacroiliitis, spondylitis and arthritis. Radiological diagnosis of inflammatory changes of sacroiliac joints is based on a 4 step radiographic grading method from 1966. According to modified New York criteria, the diagnosis of ankylosing spondylitis is made based on the presence of advanced lesions, sacroiliitis of at least 2 grade bilaterally or 3–4 unilaterally. In case of other types of spondyloarthropathies diagnosis is made based on presence of at least grade 1 changes. In MRI, active inflammation of sacroiliac joints is indicated by the presence of subchondral bone marrow edema, synovitis, bursitis, or enthesitis. ASAS discusses only the classic form of axial spondyloarthropathies, which is ankylosing spondylitis. To quantify radiological inflammatory changes in the course of the disease, Stoke Ankylosing spondylitis classification Spinal Score (SASSS) is recommended. The signs of inflammation and scarrying of the spinal cord in the course of ankylosing spondylitis, present in MRI include: bone marrow edema, sclerosis, fat metaplasia, formation of syndesmophytes, and ankylosis

Improvement of visualization efficiency for the nondestructive inspection image of internal defects in plate type nuclear fuel

International Nuclear Information System (INIS)

Park, Seung Kyu; Park, Nak Kyu; Baik, Sung Hoon; Lee, Yoon Sang; Cheong, Yong Moo; Kang, Young June

2012-01-01

Plate type nuclear fuel has been adopted in most research reactors. The production quality of the fuel is a key part for an efficient and stable generation of thermal energy in research reactors. Thus, a nondestructive quality inspection for the internal defects of plate type nuclear fuel is a key process during the production of nuclear fuel for safety insurance. Nondestructive quality inspections based on X rays and ultrasounds have been widely used for the defect detection of plate type nuclear fuel. X ray testing is a simple and fast inspection method, and provides an image in real time as the inspection results. Thus, the testing can be carried out by a non expert field worker. However, it is hard to detect closed type defects that should be detected during the production of plate type nuclear fuel. Ultrasonic testing is a powerful tool to detect internal defects including open type and closed type defects in plate type nuclear fuel. However, the inspection process is complicated because an immersion test should be carried out in a water tank. It is also a time consuming inspection method because area testing to acquire image is based on the scanning of the point by point inspections. Among nondestructive inspection techniques, the techniques based on laser interferometry and infrared thermography have been widely used in the detection of internal defects of plate type composite materials, such as aircraft, automotive etc. While infrared thermography technique (IRT) analyses the thermal behavior of the specimen surface, laser interferometry technique (LIT) analyses the deformation field. Both techniques are useful tools for detection and evaluation of internal defects in composite materials. Especially, the laser interferometry technique can provide the depth information of internal defects. Laser interferometry technique (LIT) is a non contact inspection method faster than thermography. Also, this technique requires less energy than thermography and the

EFFECT OF INFLIXIMAB ON DYNAMICS OF FUNCTIONAL CLASS AND RADIOLOGICAL SIGN OF BONE AND CARTILAGINOUS TISSUES ALTERATION OF JOINTS IN PATIENTS WITH DIFFERENT TYPES OF JUVENILE ARTHRITIS

Directory of Open Access Journals (Sweden)

E.I. Alexeeva

2008-01-01

Full Text Available An objective of this trial was evaluation of effect of treatment with blocker of tumor necrosis factor infliximab on dynamics of functional class and radiological changes of bone and cartilaginous tissue of joints in children with different clinical types of juvenile arthritis (JA. Infliximab was used according to standard scheme on 0, 2, 6 and then every 8 week by intravenous infusion. Mean single dose of infliximab was 6,8 ± 2,3 mg/kg. All children were treated with immunosuppressive agents (ciclosporin in 6% of patients, methotrexate in 60%, ciclosporin combined with methotrexate — 20%, ciclosporin with leflunomide — 5%, leflunomide with methotreate — 4% combined with anti cytokine treatment. 7 children were treated with oral glucocorticoids in mean dose 0,37 mg/kg daily. disorders in joint function and structural changes of joints of different severity (radiological sign were discovered in all patients before starting of treatment with infliximab. Duration of observation was 6 week — 2 years. Authors made a conclusion that treatment with infliximab prevents progressing of bone and cartilaginous destruction in all types of AJ, not depending on intensity of its clinical activity. This medication provides for full functional recovery of joints and elimination of features of disablement in patients with good clinical activity.Key words: children, juvenile arthritis, infliximab, treatment.

Effect of Solder-Joint Geometry on the Low-Cycle Fatigue Behavior of Sn- xAg-0.7Cu

Science.gov (United States)

Lee, Hwa-Teng; Huang, Kuo-Chen

2016-12-01

Low-cycle fatigue tests of Sn-Ag-Cu (SAC) Pb-free solder joints under fixed displacement were performed to evaluate the influence of Ag content (0-3 wt.%) and solder-joint geometry (barrel and hourglass types) on solder-joint fatigue behavior and reliability. The solder joints were composed of fine particles of Ag3Sn and Cu6Sn5, which aggregated as an eutectic constituent at grain boundaries of the primary β-Sn phase and formed a dense network structure. A decrease in the Ag content resulted in coarsening of the β-Sn and eutectic phases, which, in turn, decreased the strength of the joint and caused earlier failure. Solder joints in the hourglass form exhibited better fatigue performance with longer life than barrel-type joints. The sharp contact angle formed between the solder and the Cu substrate by the barrel-type joints concentrated stress, which compromised fatigue reliability. The addition of Ag to the solder, however, enhanced fatigue performance because of strengthening caused by Ag3Sn formation. The cracks of the barrel-type SAC solder joints originated mostly at the contact corner and propagated along the interfacial layer between the interfacial intermetallic compound (IMC) and solder matrix. Hourglass-type solder joints, however, demonstrated both crack initiation and propagation in the solder matrix (solder mode). The addition of 1.5-2.0 wt.% Ag to SAC solder appears to enhance the fatigue performance of solder joints while maintaining sufficient strength.

Study for a stress joint at the top of a SCR (Steel Catenary Risers); Estudo de 'stress joints' para o topo de um SCR (Steel Catenary Risers)

Energy Technology Data Exchange (ETDEWEB)

Siqueira, Elizabeth Frauches Netto; Andrade, Edmundo Queiroz de [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

Steel Catenary Risers, SCRs, need a top connection that bears the force transmitted to the platform. Essentially, two types of connections exist on the market: flex joint and stress joint (SJ). PETROBRAS has a SCR with top connection of flex joint type installed on one of its platforms; however, the company has been studying SJ as an option out of SCR top connection. A stress joint is a monolithic structure and can be inspected during manufacture and service, without so many difficult. They are metal structures composed of a uniform bore inserted in a tapered wall that increases gradually to support the force coming from the riser. The objective of this paper is to present a SJ sensitivity study for a production SCR supposedly hardwired to a unit of production of the semi-submersible type. The data used is based on real SCR data. For this study, global and local analyses were conducted for some models of stress joints, varying some parameters such as material and dimensions, allowing for the verification of some of the critical points of this type of connection. The results obtained will be shown in graphs and tensions maps to illustrate comparatively the critical points of the models analyzed. (author)

The Agency's Agreement with the United Nations Educational, Scientific and Cultural Organization concerning the Joint Operation of the International Centre for Theoretical Physics at Trieste. Extension of the Agreement

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-02-15

By an exchange of letters between the Directors General of the United Nations Educational, Scientific and Cultural Organization (UNESCO) and the Agency, the duration of the agreement between the two organizations concerning the joint operation of the International Centre for Theoretical Physics at Trieste has been extended until 31 December 1986.

The Agency's Agreement with the United Nations Educational, Scientific and Cultural Organization concerning the Joint Operation of the International Centre for Theoretical Physics at Trieste. Extension of the Agreement

International Nuclear Information System (INIS)

1983-02-01

By an exchange of letters between the Directors General of the United Nations Educational, Scientific and Cultural Organization (UNESCO) and the Agency, the duration of the agreement between the two organizations concerning the joint operation of the International Centre for Theoretical Physics at Trieste has been extended until 31 December 1986.

Joints of pipes without welding. Uniones sin soldadura de tuberias

Energy Technology Data Exchange (ETDEWEB)

Hemmi, H [GS-Hydro, S.A. (Spain)

1993-01-01

The joint pipes without welding save fabrication time and contribute to save money. There are four solutions depending on the work pressure and type of pipe: retaining ring, expander, mechanical joint. These systems are applied to chemical industry, offshore and terrestrial industry. (Author)

THE IMPACT OF TRUST ON KNOWLEDGE TRANSFER IN INTERNATIONAL BUSINESS SYSTEMS

Directory of Open Access Journals (Sweden)

Konstantinos P. ROTSIOS

2012-12-01

Full Text Available Over the last decade, international business alliances have emerged as one of the most important strategies for firms to expand in international markets. In addition, knowledge transfer has been determined as one of the key factors that lead to the creation of sustainable competitive advantage for firms and to the success of learning alliances. Furthermore, trust enhances the effectiveness of this process. The growing volume of published research in recent years has indubitably revealed the significant role of trust on knowledge transfer in International Business (IB Systems and in particular in International Strategic Alliances (ISAs and International Joint Ventures (IJVs. This paper consists of an in depth review of the most recent literature about the impact of trust on transfer of various types of knowledge in IB Systems with reference to the relevant theoretical models and the applications in the international context. The first section contains the theoretical background of the concept of trust, the different types of knowledge and the process of knowledge transfer. The main section refers to a few contemporary and distinguished scientific articles about the impact of trust as a determinant factor of knowledge transfer from the most recent international literature. The conclusions of the literature review and testable propositions related to the creation of trust among IJV partners and their impact on knowledge transfer are presented at the final section of the paper.

Integrating Quantitative and Qualitative Results in Health Science Mixed Methods Research Through Joint Displays.

Science.gov (United States)

Guetterman, Timothy C; Fetters, Michael D; Creswell, John W

2015-11-01

Mixed methods research is becoming an important methodology to investigate complex health-related topics, yet the meaningful integration of qualitative and quantitative data remains elusive and needs further development. A promising innovation to facilitate integration is the use of visual joint displays that bring data together visually to draw out new insights. The purpose of this study was to identify exemplar joint displays by analyzing the various types of joint displays being used in published articles. We searched for empirical articles that included joint displays in 3 journals that publish state-of-the-art mixed methods research. We analyzed each of 19 identified joint displays to extract the type of display, mixed methods design, purpose, rationale, qualitative and quantitative data sources, integration approaches, and analytic strategies. Our analysis focused on what each display communicated and its representation of mixed methods analysis. The most prevalent types of joint displays were statistics-by-themes and side-by-side comparisons. Innovative joint displays connected findings to theoretical frameworks or recommendations. Researchers used joint displays for convergent, explanatory sequential, exploratory sequential, and intervention designs. We identified exemplars for each of these designs by analyzing the inferences gained through using the joint display. Exemplars represented mixed methods integration, presented integrated results, and yielded new insights. Joint displays appear to provide a structure to discuss the integrated analysis and assist both researchers and readers in understanding how mixed methods provides new insights. We encourage researchers to use joint displays to integrate and represent mixed methods analysis and discuss their value. © 2015 Annals of Family Medicine, Inc.

Integrating Quantitative and Qualitative Results in Health Science Mixed Methods Research Through Joint Displays

Science.gov (United States)

Guetterman, Timothy C.; Fetters, Michael D.; Creswell, John W.

2015-01-01

PURPOSE Mixed methods research is becoming an important methodology to investigate complex health-related topics, yet the meaningful integration of qualitative and quantitative data remains elusive and needs further development. A promising innovation to facilitate integration is the use of visual joint displays that bring data together visually to draw out new insights. The purpose of this study was to identify exemplar joint displays by analyzing the various types of joint displays being used in published articles. METHODS We searched for empirical articles that included joint displays in 3 journals that publish state-of-the-art mixed methods research. We analyzed each of 19 identified joint displays to extract the type of display, mixed methods design, purpose, rationale, qualitative and quantitative data sources, integration approaches, and analytic strategies. Our analysis focused on what each display communicated and its representation of mixed methods analysis. RESULTS The most prevalent types of joint displays were statistics-by-themes and side-by-side comparisons. Innovative joint displays connected findings to theoretical frameworks or recommendations. Researchers used joint displays for convergent, explanatory sequential, exploratory sequential, and intervention designs. We identified exemplars for each of these designs by analyzing the inferences gained through using the joint display. Exemplars represented mixed methods integration, presented integrated results, and yielded new insights. CONCLUSIONS Joint displays appear to provide a structure to discuss the integrated analysis and assist both researchers and readers in understanding how mixed methods provides new insights. We encourage researchers to use joint displays to integrate and represent mixed methods analysis and discuss their value. PMID:26553895

Intra-articular elastofibroma of the shoulder joint

International Nuclear Information System (INIS)

Bae, Sang-Jin; Shin, Myung Jin; Kim, Sung Moon; Cho, Kyung-Ja

2002-01-01

A 19-year-old man presented with an elastofibroma in his left shoulder joint. The patient had had limitation of motion in his left arm for 3 years, especially when rotating internally. Radiography of his left shoulder showed bone erosion in the neck of the humerus. On MR imaging, a soft tissue mass was noted in the shoulder joint eroding bone. The mass showed similar signal intensity to that of surrounding muscles on T1- and T2-weighted images. At surgery, a soft, encapsulated mass was found attached to the subscapularis muscle. It was pathologically confirmed as an elastofibroma. This unusual manifestation of an elastofibroma is discussed. (orig.)

Interobserver and intraobserver reliability of radiographic classification of acromioclavicular joint dislocations.

Science.gov (United States)

Ringenberg, Jonathan D; Foughty, Zachary; Hall, Adam D; Aldridge, J Mack; Wilson, Joseph B; Kuremsky, Marshall A

2018-03-01

The classification and treatment of acromioclavicular (AC) joint dislocations remain controversial. The purpose of this study was to determine the interobserver and intraobserver reliability of the Rockwood classification system. We hypothesized poor interobserver and intraobserver reliability, limiting the role of the Rockwood classification system in determining severity of AC joint dislocations and accurately guiding treatment decisions. We identified 200 patients with AC joint injuries using the International Classification of Diseases, Ninth Revision code 831.04. Fifty patients met inclusion criteria. Deidentified radiographs were compiled and presented to 6 fellowship-trained upper extremity orthopedic surgeons. The surgeons classified each patient into 1 of the 6 classification types described by Rockwood. A second review was performed several months later by 2 surgeons. A κ value was calculated to determine the interobserver and intraobserver reliability. The interobserver and intraobserver κ values were fair (κ = 0.278) and moderate (κ = 0.468), respectively. Interobserver results showed that 4 of the 50 radiographic images had a unanimous classification. Intraobserver results for the 2 surgeons showed that 18 of the 50 images were rated the same on second review by the first surgeon and 38 of the 50 images were rated the same on second review by the second surgeon. We found that the Rockwood classification system has limited interobserver and intraobserver reliability. We believe that unreliable classification may account for some of the inconsistent treatment outcomes among patients with similarly classified injuries. We suggest that a better classification system is needed to use radiographic imaging for diagnosis and treatment of AC joint dislocations. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

Mo-based compounds for SiC-SiC joints

Energy Technology Data Exchange (ETDEWEB)

Magnani, G.; Beaulardi, L.; Mingazzini, C. [ENEA-Faenza (Italy). New Material Div.; Marmo, E. [Fabbricazioni Nucleari S.p.A., Bosco Mavengo (Italy)

2002-07-01

New method to joint silicon carbide-based material was developed. It was based on mixture composed mainly by molybdenum silicides. This mixture was tested as brazing mixture with several types of silicon carbide-based material. Microstructural examination of the joint showed that brazing mixture reacted with substrate to form silicon carbide on the surface, while two different molybdenum silicides were identified inside the joint (MoSi{sub 2} and Mo{sub 4.8}Si{sub 3}C{sub 0.6}). Preliminary oxidation tests performed by means of TGA showed high oxidation resistance of this joint over 1000 C making it very promising for high temperature application like ceramic heat exchanger. (orig.)

MR diagnosis of temporomandibular joint. A study of joint effusion

International Nuclear Information System (INIS)

Kaneda, Takashi; Yamashiro, Mitsuaki; Ozawa, Kaoru; Suzuki, Hiromi; Okada, Hiroyuki; Yamamoto, Hirotsugu

1998-01-01

The purposes of this study were to evaluate the relationship between correlation of MR joint effusion of the temporomandibular joint and disk position, to evaluate the relationship between joint effusion and aging, and to assess the frequency of MR joint effusion of bilateral temporomandibular joints. The temporomandibular joints of 192 patients with clinical symptoms of temporomandibular joint disorders were imaged bilaterally using high field, surface-coil MR imaging. Oblique sagittal and coronal proton density-weighted and T2-weighted images were obtained. Imaging findings of joint effusion were correlated with disk position, aging, and bilateral temporomandibular joints. MR showed effusion in 4% of the joints with normal superior disk position, 36% of the joints with disk displacement with reduction, and 45% of the joints with disk displacement without reduction. There were significant differences in the incidence of joint effusion between normal disk position and anterior disk displacement with or without reduction. Younger patients less than 40 years were significant higher the incidence of joint effusion than those of older patients. A significant association was seen between joint effusion and aging. MR showed effusion in 17% of the unilateral temporomandibular joint, 24% of the bilateral temporomandibular joints. There was no significant difference between unilateral and bilateral case. These results indicated that joint effusion using MR imaging was associated with varied temporomandibular joint pathologic states. (author)

Paranormal weighted conditional type operators

OpenAIRE

Estaremi, Yousef

2014-01-01

In this paper, some sub-classes of paranormal weighted conditional expectation type operators, such as *-paranormal, quasi-*-paranormal and (n; k)-quasi-*-paranormal weighted conditional expectation type opera- tors on $L^2(\\Sigma)$ are investigated. Also, some applications about the spectrum, point spectrum, joint point spectrum, approximate point spectrum and joint approximate point spectrum of these classes are presented.

Pseudodynamic MR imaging of temporomandibular joint disorders

International Nuclear Information System (INIS)

Nakasato, Tatsuhiko; Ehara, Shigeru

1992-01-01

Magnetic resonance (MR) imaging of the temporomandibular joint (TMJ) has now been established as a procedure of choice in the evaluation of TMJ disorders. In this study, we evaluated the dynamics of TMJ motion on MR imaging, which resembles arthrography. Sixty-eight TMJs in 38 symptomatic patients and one healthy volunteer were examined using pseudodynamic images with gradient echo sequences using a 0.5 Tesla MR unit and 8 cm circular planar surface coil. For depiction of each compartment of the meniscus, the optimum sequence was 200/15/2 (TR/TE/excitations) with 50 deg or 60 deg flip angle in gradient refocused acquisition in steady-state (GRASS) sequences. Three contiguous slices on sagittal MR images were routinely obtained at 14-18 different phases of the opening cycle and displayed in closed-loop cine fashion. Internal derangement was observed in 57% of 68 joints. The most common type was anterior meniscal displacement without reduction. Sideway and rotational displacements, observed in 10% each, were noted on both sagittal multislice images and axial reference images. As a pseudodynamic MR technique, jaw movement specifically designed to check bite procedure to adjust splints is useful for detecting the exact time of meniscal redisplacement on the second click. After conservative therapy for arthrosis, pseudodynamic MR provided information on changes in the meniscus and condylar relationship. Pseudodynamic MR with multiple phases is suitable for evaluating subtle motion abnormality of the meniscus and for post-therapeutic monitoring. (author)

Pseudodynamic MR imaging of temporomandibular joint disorders

Energy Technology Data Exchange (ETDEWEB)

Nakasato, Tatsuhiko; Ehara, Shigeru (Iwate Medical Coll., Morioka (Japan). School of Medicine)

1992-09-01

Magnetic resonance (MR) imaging of the temporomandibular joint (TMJ) has now been established as a procedure of choice in the evaluation of TMJ disorders. In this study, we evaluated the dynamics of TMJ motion on MR imaging, which resembles arthrography. Sixty-eight TMJs in 38 symptomatic patients and one healthy volunteer were examined using pseudodynamic images with gradient echo sequences using a 0.5 Tesla MR unit and 8 cm circular planar surface coil. For depiction of each compartment of the meniscus, the optimum sequence was 200/15/2 (TR/TE/excitations) with 50 deg or 60 deg flip angle in gradient refocused acquisition in steady-state (GRASS) sequences. Three contiguous slices on sagittal MR images were routinely obtained at 14-18 different phases of the opening cycle and displayed in closed-loop cine fashion. Internal derangement was observed in 57% of 68 joints. The most common type was anterior meniscal displacement without reduction. Sideway and rotational displacements, observed in 10% each, were noted on both sagittal multislice images and axial reference images. As a pseudodynamic MR technique, jaw movement specifically designed to check bite procedure to adjust splints is useful for detecting the exact time of meniscal redisplacement on the second click. After conservative therapy for arthrosis, pseudodynamic MR provided information on changes in the meniscus and condylar relationship. Pseudodynamic MR with multiple phases is suitable for evaluating subtle motion abnormality of the meniscus and for post-therapeutic monitoring. (author).

Expansion joints for LMFBR

International Nuclear Information System (INIS)

Dzenus, M.; Hundhausen, W.; Jansing, W.

1980-01-01

This discourse recounts efforts put into the SNR-2 project; specifically the development of compensation devices. The various prototypes of these compensation devices are described and the state of the development reviewed. Large Na (sodium)-heat transfer systems require a lot of valuable space if the component lay-out does not include compensation devices. So, in order to condense the spatial requirement as much as possible, expansion joints must be integrated into the pipe system. There are two basic types to suit the purpose: axial expansion joints and angular expansion joints. The expansion joints were developed on the basis of specific design criteria whereby differentiation is made between expansion joints of small and large nominal diameter. Expansion joints for installation in the sodium-filled primary piping are equipped with safety bellows in addition to the actual working bellows. Expansion joints must be designed and mounted in a manner to completely withstand seismic forces. The design must exclude any damage to the bellows during intermittent operations, that is, when sodium is drained the bellows' folds must be completely empty; otherwise residual solidified sodium could destroy the bellows when restarting. The expansion joints must be engineered on the basis of the following design data for the secondary system of the SNR project: working pressure: 16 bar; failure mode pressure: 5 events; failure mode: 5 sec., 28.5 bar, 520 deg. C; working temperature: 520 deg. C; temperature transients: 30 deg. C/sec.; service life: 200,000 h; number of load cycles: 10 4 ; material: 1.4948 or 1.4919; layer thickness of folds: 0.5 mm; angular deflection (DN 800): +3 deg. C or; axial expansion absorption (DN 600): ±80 mm; calculation: ASME class. The bellows' development work is not handled within this scope. The bellows are supplied by leading manufacturers, and warrant highest quality. Multiple bellows were selected on the basis of maximum elasticity - a property

Alpha C-telopeptide of type I collagen is associated with subchondral bone turnover and predicts progression of joint space narrowing and osteophytes in osteoarthritis.

Science.gov (United States)

Huebner, Janet L; Bay-Jensen, Anne C; Huffman, Kim M; He, Yi; Leeming, Diana J; McDaniel, Gary E; Karsdal, Morten A; Kraus, Virginia B

2014-09-01

To evaluate joint tissue remodeling using the urinary collagen biomarkers urinary α-C-telopeptide of type I collagen (α-CTX) and urinary C-telopeptide of type II collagen (CTX-II) and to determine the association of these biomarkers with osteoarthritis (OA) severity, progression, and localized knee bone turnover. Participants (n = 149) with symptomatic and radiographic knee OA underwent fixed-flexion knee radiography at baseline and 3 years, and late-phase bone scintigraphy of both knees at baseline, which were scored semiquantitatively for osteophyte and joint space narrowing (JSN) severity and uptake intensity, with scores summed across knees. Urinary concentrations of α-CTX and CTX-II were determined by enzyme-linked immunosorbent assay. Immunohistochemical analysis of human OA knees was performed to localize the joint tissue origin of the biomarker epitopes. Urinary α-CTX concentrations correlated strongly with the intensity of bone scintigraphic uptake and with JSN progression (risk ratio 13.2) and osteophyte progression (risk ratio 3). Urinary CTX-II concentrations were strongly associated with intensity of bone scintigraphic uptake, with JSN and osteophyte severity, and with OA progression based on osteophyte score. Urinary α-CTX localized primarily to high bone turnover areas in subchondral bone. CTX-II localized to the bone-cartilage interface, the tidemark, and damaged articular cartilage. Baseline urinary α-CTX, which was localized to high turnover areas of subchondral bone, was associated with dynamic bone turnover of knees, as signified by scintigraphy, and progression of both osteophytes and JSN. Urinary CTX-II correlated with JSN and osteophyte severity and progression of osteophytes. To our knowledge, this represents the first report of serologic markers reflecting subchondral bone turnover. These collagen markers may be useful for noninvasive detection and quantification of active subchondral bone turnover and joint remodeling in knee OA

Design and Testing of Low Cost Chair with Round Mortise and Tenon Joints

Directory of Open Access Journals (Sweden)

Jaroslav Začal

2016-01-01

Full Text Available The present paper focuses on construction of school seats for developing countries from locally available resources using the local industry and low-end technology. Aim of the work is experimental assessment of mechanical properties of joints flexion in angular plane. Furthermore work considers assessment of joint firmness and comparison between various joint types. Paper encloses the review of various joint manufacturing designs (tenon and mortise, which were proposed for its suitable mechanical properties and simplicity of manufacturing. Designated joint type is easiest form of joint construction and technologically feasible for chair manufacturing. The joints were constructed from fir wood. Further the work introduces design of simple seat construction made from massive wood material manufactured by low-end technology with regards to achieving the due specifications. The task of this work is to design the viable manufacturing process of seats and chairs from raw wood and scrap material. Essential part of work is also manufacturing of seat prototype and simplified model of proposed mortise and tenon drill.

A joint model for repeated events of different types and multiple longitudinal outcomes with application to a follow-up study of patients after kidney transplant

NARCIS (Netherlands)

Musoro, Jammbe Z.; Geskus, Ronald B.; Zwinderman, Aeilko H.

2015-01-01

This paper presents an extension of the joint modeling strategy for the case of multiple longitudinal outcomes and repeated infections of different types over time, motivated by postkidney transplantation data. Our model comprises two parts linked by shared latent terms. On the one hand is a

Management of acute unstable acromioclavicular joint injuries.

Science.gov (United States)

Cisneros, Luis Natera; Reiriz, Juan Sarasquete

2016-12-01

Surgical management of acute unstable acromioclavicular joint injuries should be focused on realigning the torn ends of the ligaments to allow for healing potential. The most widely utilized treatment methods incorporate the use of metal hardware, which can alter the biomechanics of the acromioclavicular joint. This leads to a second surgical procedure for hardware removal once the ligaments have healed. Patients with unstable acromioclavicular joint injuries managed with arthroscopy-assisted procedures have shown good and excellent clinical outcomes, without the need for a second operation. These procedures incorporate a coracoclavicular suspension device aimed to function as an internal brace, narrowing the coracoclavicular space thus allowing for healing of the torn coracoclavicular ligaments. The lesser morbidity of a minimally invasive approach and the possibility to diagnose and treat concomitant intraarticular injuries; no obligatory implant removal, and the possibility of having a straight visualization of the inferior aspect of the base of the coracoid (convenient when placing coracoclavicular fixation systems) are the main advantages of the arthroscopic approach over classic open procedures. This article consists on a narrative review of the literature in regard to the management of acute acromioclavicular joint instability.

Is coracoclavicular stabilisation alone sufficient for the endoscopic treatment of severe acromioclavicular joint dislocation (Rockwood types III, IV, and V)?

Science.gov (United States)

Barth, J; Duparc, F; Andrieu, K; Duport, M; Toussaint, B; Bertiaux, S; Clavert, P; Gastaud, O; Brassart, N; Beaudouin, E; De Mourgues, P; Berne, D; Bahurel, J; Najihi, N; Boyer, P; Faivre, B; Meyer, A; Nourissat, G; Poulain, S; Bruchou, F; Ménard, J F

2015-12-01

The primary objective was to evaluate correlations linking anatomical to functional outcomes after endoscopically assisted repair of acute acromioclavicular joint dislocation (ACJD). Combined acromioclavicular and coracoclavicular stabilisation improves radiological outcomes compared to coracoclavicular stabilisation alone. A prospective multicentre study was performed. Clinical outcome measures were pain intensity on a visual analogue scale (VAS), subjective functional impairment (QuickDASH score), and Constant's score. Anatomical outcomes were assessed on standard radiographs (anteroposterior view of the acromioclavicular girdle and bilateral axillary views) obtained preoperatively and postoperatively and on postoperative dynamic radiographs taken as described by Tauber et al. Of 116 patients with acute ACJD included in the study, 48% had type III, 30% type IV, and 22% type V ACJD according to the Rockwood classification. Coracoclavicular stabilisation was achieved using a double endobutton in 93% of patients, and concomitant acromioclavicular stabilisation was performed in 50% of patients. The objective functional outcome was good, with an unweighted Constant's score ≥ 85/100 and a subjective QuickDASH functional disability score ≤ 10 in 75% of patients. The radiographic analysis showed significant improvements from the preoperative to the 1-year postoperative values in the vertical plane (decrease in the coracoclavicular ratio from 214 to 128%, p=10(-6)) and in the horizontal plane (decrease in posterior displacement from 4 to 0mm, p=5×10(-5)). The anatomical outcome correlated significantly with the functional outcome (absolute R value=0.19 and p=0.045). We found no statistically significant differences across the various types of constructs used. Intra-operative control of the acromioclavicular joint did not improve the result. Implantation of a biological graft significantly improved both the anatomical outcome in the vertical plane (p=0.04) and

The effect of polyethylene creep on tibial insert locking screw loosening and back-out in prosthetic knee joints.

Science.gov (United States)

Sanders, Anthony P; Raeymaekers, Bart

2014-10-01

A prosthetic knee joint typically comprises a cobalt-chromium femoral component that articulates with a polyethylene tibial insert. A locking screw may be used to prevent micromotion and dislodgement of the tibial insert from the tibial tray. Screw loosening and back-out have been reported, but the mechanism that causes screw loosening is currently not well understood. In this paper, we experimentally evaluate the effect of polyethylene creep on the preload of the locking screw. We find that the preload decreases significantly as a result of polyethylene creep, which reduces the torque required to loosen the locking screw. The torque applied to the tibial insert due to internal/external rotation within the knee joint during gait could thus drive locking screw loosening and back-out. The results are very similar for different types of polyethylene. Copyright © 2014 Elsevier Ltd. All rights reserved.

Intelligent screening of electrofusion-polyethylene joints based on a thermal NDT method

Science.gov (United States)

Doaei, Marjan; Tavallali, M. Sadegh

2018-05-01

The combinations of infrared thermal images and artificial intelligence methods have opened new avenues for pushing the boundaries of available testing methods. Hence, in the current study, a novel thermal non-destructive testing method for polyethylene electrofusion joints was combined with k-means clustering algorithms as an intelligent screening tool. The experiments focused on ovality of pipes in the coupler, as well as misalignment of pipes-couplers in 25 mm diameter joints. The temperature responses of each joint to an internal heat pulse were recorded by an IR thermal camera, and further processed to identify the faulty joints. The results represented clustering accuracy of 92%, as well as more than 90% abnormality detection capabilities.

Joint Technical Coordinating Group on Aircraft Survivability (JTCG/AS). Bibliography of Joint Aircraft Survivability Reports

Science.gov (United States)

2000-07-01

PMSG ). Report No.: JTCG/AS-99-D-003 Report Classification: UNCLASSIFIED Title: JTCG/AS Bibliography of Joint Aircraft Survivability Reports and...indicates those approved and not approved for funding by the Principal Members Steering Group ( PMSG ). Report No.: Report Classification: JTCG/AS-97-V-010...demonstrated by additional tests conducted at NWSC/Crane (up to Mach 0.8) and Rockwell International wind tunnel (up to Mach 1/9 and 30,000 feet altitude

The mechanisms behind decreased internalization of angiotensin II type 1 receptor.

Science.gov (United States)

Bian, Jingwei; Zhang, Suli; Yi, Ming; Yue, Mingming; Liu, Huirong

2018-04-01

The internalization of angiotensin II type 1 receptor (AT 1 R) plays an important role in maintaining cardiovascular homeostasis. Decreased receptor internalization is closely related to cardiovascular diseases induced by the abnormal activation of AT 1 R, such as hypertension. However, the mechanism behind reduced AT 1 R internalization is not fully understood. This review focuses on four parts of the receptor internalization process (the combination of agonists and receptors, receptor phosphorylation, endocytosis, and recycling) and summarizes the possible mechanisms by which AT 1 R internalization is reduced based on these four parts of the process. (1) The agonist has a large molecular weight or a stronger ability to hydrolyze phosphatidylinositol 4,5-bisphosphate (PtdIns (4,5) P 2 ), which can increase the consumption of PtdIns (4,5) P 2 . (2) AT 1 R phosphorylation is weakened because of an abnormal function of phosphorylated kinase or changes in phospho-barcoding and GPCR-β-arrestin complex conformation. (3) The abnormal formation of vesicles or AT 1 R heterodimers with fewer endocytic receptors results in less AT 1 R endocytosis. (4) The enhanced activity and upregulated expression of small GTP-binding protein 4 (Rab4) and 11 (Rab11), which regulate receptor recycling, and phosphatidylinositol 3-kinase increase AT 1 R recycling. In addition, lower expression of AT 1 R-associated protein (ATRAP) or higher expression of AT 1 R-associated protein 1 (ARAP1) can reduce receptor internalization. Copyright © 2018 Elsevier Inc. All rights reserved.

Contemporary forms of international movement of capital

Directory of Open Access Journals (Sweden)

Sanja Šovran

2016-11-01

Full Text Available International movement of capital is one of the most important forms of international economic cooperation and achievement of strategic goals of enterprises. It leads to international diversification of business activities, strengthening of competitive advantage, changes in economic structures, employment rates and economic stability of participating countries. The present research addresses the contemporary forms of international movement of capital, with an emphasis on the public-private partnerships and concessions. The creation of different forms of public-private partnerships (PPPs in Serbia gained in importance in the early ‘90s of the 20th century. PPP implies joint activities within the framework of which the public and private sector pool resources, especially financial capital and expertise in order to meet the public needs of local, regional or national significance for adequate resource allocation. This type of partnership between the public and private sector has become an effective way towards a more rational use of limited resources and development of business entities from different sectors. The partnership of the public and private sector is particularly important in the construction and maintenance of transportation and other infrastructure facilities. Concessions represent a special form of public-private partnerships.

Radiographic evaluation of cervical spine of subjects with temporomandibular joint internal disorder Avaliação radiográfica da coluna cervical de indivíduos com distúrbios internos da articulação temporomandibular

OpenAIRE

Wagner Cesar Munhoz; Amélia Pasqual Marques; José Tadeu Tesseroli de Siqueira

2004-01-01

Although the etiopathophysiology of internal temporomandibular joint internal disorders (TMJ ID) is still unknown, it has been suggested that head and body posture could be related to its initial onset, development and perpetuation. The purpose of the present study was to observe the relationship between cervical spine X-ray abnormalities and TMJ ID. This investigation evaluated 30 subjects with internal TMJ disorder symptoms (test group) and 20 healthy subjects (control group). Subjects were...

Associations between serum ghrelin and knee symptoms, joint structures and cartilage or bone biomarkers in patients with knee osteoarthritis.

Science.gov (United States)

Wu, J; Wang, K; Xu, J; Ruan, G; Zhu, Q; Cai, J; Ren, J; Zheng, S; Zhu, Z; Otahal, P; Ding, C

2017-09-01

The roles of ghrelin in knee osteoarthritis (OA) are unclear. This study aimed to examine cross-sectional associations of ghrelin with knee symptoms, joint structures and cartilage or bone biomarkers in patients with knee OA. This study included 146 patients with symptomatic knee OA. Serum levels of ghrelin and cartilage or bone biomarkers including cartilage oligomeric matrix protein (COMP), cross linked C-telopeptide of type I collagen (CTXI), cross linked N-telopeptide of type I collagen (NTXI), N-terminal procollagen III propeptide (PIIINP), and matrix metalloproteinase (MMP)-3, 10, 13 were measured using Enzyme-linked immunosorbent assay (ELISA). Knee symptoms were assessed using the Western Ontario and McMaster Universities Arthritis Index (WOMAC). Infrapatellar fat pad (IPFP) volume, IPFP signal intensity alternation, cartilage defects, bone marrow lesions (BMLs) and effusion-synovitis were assessed using the (MRI). Osteophytes and joint space narrowing (JSN) were assessed using the Osteoarthritis Research Society International atlas. After adjustment for potential confounders, ghrelin quartiles were positively associated with knee symptoms including pain, stiffness, dysfunction and total score (quartile 4 vs 1: β 24.19, 95% CI 8.13-40.25). Ghrelin quartiles were also significantly associated with increased IPFP signal intensity alteration (quartile 4 vs 1: OR 3.57, 95% CI 1.55-8.25) and NTXI, PIIINP, MMP3 and MMP13. Ghrelin was not significantly associated with other joint structures and biomarkers. Serum levels of ghrelin were significantly associated with increased knee symptoms, IPFP signal intensity alteration and serum levels of MMP3, MMP13, NTXI and PIIINP, suggesting that ghrelin may have a role to play in knee OA. Copyright © 2017 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Jointness through vessel capacity input in a multispecies fishery

DEFF Research Database (Denmark)

Hansen, Lars Gårn; Jensen, Carsten Lynge

2014-01-01

capacity. We develop a fixed but allocatable input model of purse seine fisheries capturing this particular type of jointness. We estimate the model for the Norwegian purse seine fishery and find that it is characterized by nonjointness, while estimations for this fishery using the standard models imply...... are typically modeled as either independent single species fisheries or using standard multispecies functional forms characterized by jointness in inputs. We argue that production of each species is essentially independent but that jointness may be caused by competition for fixed but allocable input of vessel...

Experimental study on tunnel lining joints temporarily strengthened by SMA bolts

International Nuclear Information System (INIS)

Wu, Bo; Ou, Yunlong

2014-01-01

Shield tunnels have been widely used in city metros all over the world. During the long-term period of the metro operation, the joints of shield tunnel’s neighboring segments may degrade due to some environmental factors, leading to the increasing of the joint opening and some resulting adverse consequences. In this paper, a temporary strengthening method by using shape memory alloy (SMA) bolts is proposed and experimentally studied for the joints of neighboring segments, and a revised electric heating method which suits with the strengthening method is presented and experimentally validated for the SMA bolts. The purpose of the proposed temporary strengthening method is to create favorable conditions for the following permanent strengthening. Test results show that: (a) for the joints of shield tunnel’s neighboring segments, the strengthening method can effectively reduce the joint opening, joint deflection, concrete strain in joint’s compression zone, and strain of joint’s steel bolts; (b) the revised electric heating method can be used to heat the SMA rod to a temperature higher than the SMA’s austenite finish temperature quickly, and the average heating rate related to Type 2 inner resistance element is larger than that related to Type 1 inner resistance element; and (c) the reduction percentages of the joint opening increment, joint deflection, concrete strain in joint’s compression zone, and strain of joint’s steel bolts for Specimen I are all larger than those for Specimen II, implying that the less the joint opening is, the more significant the strengthening effect is. (paper)

Comparison of Joint Loading in Badminton Lunging between Professional and Amateur Badminton Players

Directory of Open Access Journals (Sweden)

Lin Fu

2017-01-01

Full Text Available The knee and ankle are the two most injured joints associated with the sport of badminton. This study evaluates biomechanical factors between professional and amateur badminton players using an injury mechanism model. The aim of this study was to investigate the kinematic motion and kinetic loading differences of the right knee and ankle while performing a maximal right lunge. Amateur players exhibited greater ankle range of motion (p<0.05, r=0.89 and inversion joint moment (p<0.05, r=0.54 in the frontal plane as well as greater internal joint rotation moment (p<0.05, r=0.28 in the horizontal plane. In contrast, professional badminton players presented a greater knee joint moment in the sagittal (p<0.05, r=0.59 and frontal (p<0.05, r=0.37 planes, which may be associated with increased knee ligamentous injury risk. To avoid injury, the players need to forcefully extend the knee with internal rotation, strengthen the muscles around the ankle ligament, and maximise joint coordination during training. The injuries recorded and the forces responsible for the injuries seem to have developed during training activity. Training programmes and injury prevention strategies for badminton players should account for these findings to reduce potential injury to the ankle and knee.

Transcriptome-Wide Expression Profiling in Skin Fibroblasts of Patients with Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome Hypermobility Type.

Science.gov (United States)

Chiarelli, Nicola; Carini, Giulia; Zoppi, Nicoletta; Dordoni, Chiara; Ritelli, Marco; Venturini, Marina; Castori, Marco; Colombi, Marina

2016-01-01

Joint hypermobility syndrome/Ehlers-Danlos syndrome hypermobility type (JHS/EDS-HT), is likely the most common systemic heritable connective tissue disorder, and is mostly recognized by generalized joint hypermobility, joint instability complications, minor skin changes and a wide range of satellite features. JHS/EDS-HT is considered an autosomal dominant trait but is still without a defined molecular basis. The absence of (a) causative gene(s) for JHS/EDS-HT is likely attributable to marked genetic heterogeneity and/or interaction of multiple loci. In order to help in deciphering such a complex molecular background, we carried out a comprehensive immunofluorescence analysis and gene expression profiling in cultured skin fibroblasts from five women affected with JHS/EDS-HT. Protein study revealed disarray of several matrix structural components such as fibrillins, tenascins, elastin, collagens, fibronectin, and their integrin receptors. Transcriptome analysis indicated perturbation of different signaling cascades that are required for homeostatic regulation either during development or in adult tissues as well as altered expression of several genes involved in maintenance of extracellular matrix architecture and homeostasis (e.g., SPON2, TGM2, MMP16, GPC4, SULF1), cell-cell adhesion (e.g., CDH2, CHD10, PCDH9, CLDN11, FLG, DSP), immune/inflammatory/pain responses (e.g., CFD, AQP9, COLEC12, KCNQ5, PRLR), and essential for redox balance (e.g., ADH1C, AKR1C2, AKR1C3, MAOB, GSTM5). Our findings provide a picture of the gene expression profile and dysregulated pathways in JHS/EDS-HT skin fibroblasts that correlate well with the systemic phenotype of the patients.

Internal-bore-welding of 2 1/4 Cr--1 Mo steel tube-to-tubesheet joints

International Nuclear Information System (INIS)

Moorhead, A.J.; Slaughter, G.M.

1976-01-01

In order to avoid the disadvantages of the conventional face-side tube-to-tubesheet weld, the steam generators for the Clinch River Breeder Reactor Plant (a power-producing demonstration LMFBR) will be built using a relatively new technique known as internal-bore-welding (IBW). In IBW the tube does not pass through the tubesheet but rather is welded to a short stub machined on the tube side of the tubesheet. This joint has the important advantages of being inspectable by radiography and eliminating the crevice; however, it is much more difficult to weld than is the face-side design. Because of the close proximity of the tubes, there is not room for an orbiting-arc welding head on the outside of the tube. Consequently, this weld must be made by welding from the inside- or bore-side of the tube. The results are presented of the initial phases of a program undertaken at ORNL to develop improved bore-side welding equipment, to gain further understanding of this technique, and to develop mechanical property data for autogeneous welds in 2 1/4 Cr-1 Mo steel tube and tubesheet materials

[Self-assembly tissue engineering fibrocartilage model of goat temporomandibular joint disc].

Science.gov (United States)

Kang, Hong; Li, Zhen-Qiang; Bi, Yan-Da

2011-06-01

To construct self-assembly fibrocartilage model of goat temporomandibular joint disc and observe the biological characteristics of the self-assembled fibrocartilage constructs, further to provide a basis for tissue engineering of the temporomandibular joint disc and other fibrocartilage. Cells from temporomandibular joint discs of goats were harvested and cultured. 5.5 x 10(6) cells were seeded in each agarose well with diameter 5 mm x depth 10 mm, daily replace of medium, cultured for 2 weeks. One day after seeding, goat temporomandibular joint disc cells in agarose wells were gathered and began to self-assemble into a disc-shaped base, then gradually turned into a round shape. When cultured for 2 weeks, hematoxylin-eosin staining was conducted and observed that cells were round and wrapped around by the matrix. Positive Safranin-O/fast green staining for glycosaminoglycans was observed throughout the entire constructs, and picro-sirius red staining was examined and distribution of numerous type I collagen was found. Immunohistochemistry staining demonstrated brown yellow particles in cytoplasm and around extracellular matrix, which showed self-assembly construct can produce type I collagen as native temporomandibular joint disc tissue. Production of extracellular matrix in self-assembly construct as native temporomandibular joint disc tissue indicates that the use of agarose wells to construct engineered temporomandibular joint disc will be possible and practicable.

Increasing Running Step Rate Reduces Patellofemoral Joint Forces

Science.gov (United States)

Lenhart, Rachel L.; Thelen, Darryl G.; Wille, Christa M.; Chumanov, Elizabeth S.; Heiderscheit, Bryan C.

2013-01-01

Purpose Increasing step rate has been shown to elicit changes in joint kinematics and kinetics during running, and has been suggested as a possible rehabilitation strategy for runners with patellofemoral pain. The purpose of this study was to determine how altering step rate affects internal muscle forces and patellofemoral joint loads, and then to determine what kinematic and kinetic factors best predict changes in joint loading. Methods We recorded whole body kinematics of 30 healthy adults running on an instrumented treadmill at three step rate conditions (90%, 100%, and 110% of preferred step rate). We then used a 3D lower extremity musculoskeletal model to estimate muscle, patellar tendon, and patellofemoral joint forces throughout the running gait cycles. Additionally, linear regression analysis allowed us to ascertain the relative influence of limb posture and external loads on patellofemoral joint force. Results Increasing step rate to 110% of preferred reduced peak patellofemoral joint force by 14%. Peak muscle forces were also altered as a result of the increased step rate with hip, knee and ankle extensor forces, and hip abductor forces all reduced in mid-stance. Compared to the 90% step rate condition, there was a concomitant increase in peak rectus femoris and hamstring loads during early and late swing, respectively, at higher step rates. Peak stance phase knee flexion decreased with increasing step rate, and was found to be the most important predictor of the reduction in patellofemoral joint loading. Conclusion Increasing step rate is an effective strategy to reduce patellofemoral joint forces and could be effective in modulating biomechanical factors that can contribute to patellofemoral pain. PMID:23917470

Belgium and France join forces in measuring instrument research. SCK-CEN and CEA are jointly developing an innovative type of gamma detector

International Nuclear Information System (INIS)

Vermeeren, L.

2011-01-01

Real-time monitoring is extremely important to accurately interpret irradiation experiments in research reactors. SCK-CEN has years of expertise in developing sensors to monitor neutron flux, temperature, gamma radiation, etc. It has been collaborating with the CEA since 2006. Both partners share research and research results in the Laboratoire Commun de Instrumentation. Recently, a joint patent application was made for a new type of sensor to measure gamma rays.

Learning to succeed in European joint projects: the role of the modern project manager--the flow-keeper.

Science.gov (United States)

Masiello, Italo

2009-09-01

The constellation of an EU-funded project-consortium is often of very disparate culture, languages, level of knowledge and technology, social competences, experiences, ideals and ambitions that may clash with one another. Hence, coordinating and managing successful European joint projects is not an easy task. This paper addresses the learning experience of managing international research projects and, through the author's own experience and literature review, attempts to exemplify the role of the flow-keeper--a modern project manager whose particular skills are to ensure the success of EU joint projects of considerable complexity. Propositions for developing the management of international joint projects are also provided.

STAMINA OF A GASKETED BOLTED FLANGED PIPE JOINT UNDER DYNAMIC LOADING

Directory of Open Access Journals (Sweden)

Muhammad Abid

2016-11-01

Full Text Available Gasketed bolted flange joints are the most critical components in pipelines for their sealing and strength under operating conditions. Most of the work available in literature is under static loading, whereas in industry, cyclic loads are applied due to the vibrating machinery such as motors, pumps, sloshing in offshore applications and in the ships etc. In this study a three dimensional finite element analysis of a gasketed joint is carried out using a spiral wound gasket under bolt up and dynamic operating conditions (internal pressure, axial and bending singly and in combination. The cyclic axial loads are concluded relatively more challenging for both the sealing and strength of the joint. Higher magnitudes of loads and frequencies are also observed more challenging to the joints performance.

Computed tomography evaluation of the sacroiliac joints in Crohn disease

International Nuclear Information System (INIS)

Scott, W.W. Jr.; Fishman, E.K.; Kuhlman, J.E.; Caskey, C.I.; O'Brien, J.J.; Walia, G.S.; Bayless, T.M.

1990-01-01

Computed tomography (CT) was used in a prospective study of the sacroiliac joints in 86 patients with Crohn disease to determine the type and frequency of sacroiliac joint abnormalities present in this population. The CT findings were correlated with review of the clinical history in 64 patients. Computed tomography demonstrated changes of sacroiliitis in 29% of the study group. This high prevalence of sacroiliac joint abnormality was found even in those under 30 years of age. It exceeds the 11-19% previously reported from plain film examination, reflecting the greater sensitivity of CT. In the subgroup of 64 patients studied clinically, 19 (30%) had abnormal sacroiliac joints on CT, but only 2 (3%) reported symptoms related to the sacroiliac joints. (orig.)

Joint Degree Program: the Perspective of Employers

Directory of Open Access Journals (Sweden)

Tatjana Bilevičienė

2013-08-01

Full Text Available Purpose — the purpose of this article is to extend discussion towards the need and importance of joint degree programs in modern universities, introducing the perspective of the employers toward this question. Design/methodology/approach — the research was conducted to analyze the demand of joint degree programs from the perspective of employers, identify weak and strong aspects, opinion and demand for graduates of such programs. To achieve this purpose, a combination of theoretical and empirical methods was chosen: document analysis (previous studies, statistics was conducted and an online qualitative survey was organized. Findings — The analysis of articles, studies and statistics points out the challenges and threats faced by universities nowadays, forcing higher education institutions to find new ways to raise the quality of studies and raise the interest of employers to choose graduates from MRU, as well as the satisfaction of employers with their choice of employees. Theoretical analysis pointed out these challenges and requirements for the modern employee, summarised the challenges in preparation of IT field specialists. The conducted research results showed that the diploma of joint degree programs would not be treated as an advantage of possible employee from the perspective of employers in case some important aspects will not be taken into consideration by program creators. On the other hand, undeniably there are strong sides, such as knowledge in the fields of foreign language, international experience, innovativeness and creativeness of employees that would be treated as an advantage in the process of selection for positions of any technical support related positions. Research limitations/implications — employers, whose business activities are closely related to information technology, have been invited as experts. In addition, these experts have a good understanding of the specifics of joint degree programs. The received

Exploring Language and Diplomatic Thinking through Process Types: A Contrastive Study on Sino-British Diplomatic Thinking Based on the China-UK Joint Declaration

Directory of Open Access Journals (Sweden)

Song Chen

2016-07-01

Full Text Available The China-UK Joint Declaration on Building a Global Comprehensive Strategic Partnership for the 21st Century is one of the fruits of Chinese President Xi Jinping’s recent official state visit to the Great Britain. As a typical and important diplomatic language document, the Joint Declaration deserves scientific research. In this paper, based on the six process types of Halliday’s Transitivity system, we attempt to disclose the diplomatic thinking underlying the employment of process types and make a contrastive study of the diplomatic thinking of both China and the UK. The research leads to three findings. Firstly, the high frequency of material process clause in both Chinese and English versions reflects the “Action thinking”, a shared diplomatic thinking adopted by the two nations. Secondly, the Chinese version employs more relational process clauses than the English version, which is an indication of the “Relationality thinking” underlying Chinese diplomacy and it is much less emphasized or even absent in British diplomacy. Thirdly, the analysis of the mental process clauses reveals that China has an “Inclusive thinking” in its diplomatic exchange with Britain whereas the UK a “Friendship thinking”.

Tribology and total hip joint replacement: current concepts in mechanical simulation.

Science.gov (United States)

Affatato, S; Spinelli, M; Zavalloni, M; Mazzega-Fabbro, C; Viceconti, M

2008-12-01

Interest in the rheology and effects of interacting surfaces is as ancient as man. This subject can be represented by a recently coined word: tribology. This term is derived from the Greek word "tribos" and means the "science of rubbing". Friction, lubrication, and wear mechanism in the common English language means the precise field of interest of tribology. Wear of total hip prosthesis is a significant clinical problem that involves, nowadays, a too high a number of patients. In order to acquire further knowledge on the tribological phenomena that involve hip prosthesis wear tests are conducted on employed materials to extend lifetime of orthopaedic implants. The most basic type of test device is the material wear machine, however, a more advanced one may more accurately reproduce some of the in vivo conditions. Typically, these apparatus are called simulators, and, while there is no absolute definition of a joint simulator, its description as a mechanical rig used to test a joint replacement, under conditions approximating those occurring in the human body, is acceptable. Simulator tests, moreover, can be used to conduct accelerated protocols that replicate/simulate particularly extreme conditions, thus establishing the limits of performance for the material. Simulators vary in their level of sophistication and the international literature reveals many interpretations of the design of machines used for joint replacement testing. This paper aims to review the current state of the art of the hip joint simulators worldwide. This is specified through a schematic overview by describing, in particular, constructive solutions adopted to reproduce in vivo conditions. An exhaustive commentary on the evolution and actually existing simulation standards is proposed by the authors. The need of a shared protocol among research laboratories all over the world could lead to a consensus conference.

APPLICATION PROSPECTS OF THREADED JOINT OF ARMATURE

Directory of Open Access Journals (Sweden)

A. V. Radkevych

2014-06-01

Full Text Available Purpose. One of the main technological operations of buildings construction on the basis of monolithic frame systems is the production of mesh reinforcement. The current interest is the new ways specification of advanced bonding armature techniques without reliability weakness and design of the building in whole, as well as the finding of use prospects of screw-threaded joint of armature as the most technological and economic method of re-bars joints. Methodology. Advantages and disadvantages analysis of existing rebar compound technologies was implemented by couplings of different types and constructions. The most promising vertical constructions for the vertical bars joints in frameworks were determined. Findings. Researches of existing technologies of rebar joints by the couplings of different construction were carried out. The installation method of mesh reinforcement of vertical structural elements with the use of the special catching devices was developed. It allows considerably accelerating installation of mesh reinforcement. Originality. Regularity of labor intensiveness change of mesh reinforcement installation of columns at armature joint in vertical position by threaded couplings with the help of catching devices using special construction was determined. This allows substantially reducing the labor expenditures during installation of these elements. Dependency of labor intensiveness and cost of lap welding armature joints, by tub-seam welding and by thread coupling depending on its diameter was designated. Regularity of labor intensiveness changes of installation at armature joints by different methods taking into account preparatory works was defined. Practical value. The analysis of mechanical armature joints techniques was conducted. It will allow selecting methods of armature joints to increase the speed of construction works more economical and effective.

Traumatic injuries of the temporomandibular joint; Die traumatischen Kiefergelenkverletzungen

Energy Technology Data Exchange (ETDEWEB)

Puig, S.; Krestan, C.; Lomoschitz, F.; Robinson, S. [Vienna Univ. (Austria). Zentrales Inst. fuer Radiodiagnostik; Glaser, C. [Vienna Univ. (Austria). Klinik fuer Zahn-, Mund- und Kieferheilkunde; Staudenherz, A. [Vienna Univ. (Austria). Universitaetsklinik fuer Nuklearmedizin

2001-09-01

Injuries of the temporomandibular joint are mostly due to injuries or fractures of the mandibular condyle. Fractures of the skull base involving the temporomandibular joint are rare. Classification of fractures refers to their anatomical positions and the presence or absence of a luxation. Further, it is important whether the fracture is intra- or extra-capsular. The primary imaging method should be orthopantomography. As for therapy planning, especially surgery, also evaluation of soft tissue is necessary, computed tomography is the imaging method of choice. For diagnosis of complications or internal derangement of the temporomandibular joint, magnetic resonance imaging is to be recommended. (orig.) [German] Die Verletzungen des Kiefergelenks gehen zumeist mit einer Verletzung oder Fraktur des Kieferkoepfchens bzw. des Kiefergelenkfortsatzes einher. Frakturen der Schaedelbasis unter Beteiligung der Kiefergelenkpfanne sind selten. Unterschieden werden die Frakturen des Gelenkfortsatzes nach anatomischer Lokalisation und danach, ob eine Luxation vorhanden ist oder nicht. Weiter ist von Bedeutung, ob der Frakturspalt intraoder extrakapsulaer verlaeuft. Die primaere Bildgebung sollte mittels Orthopantomographie erfolgen. Da fuer eine weitere operative Behandlung auch die etwaige Verletzung der Weichteile von Bedeutung ist, bietet sich die Computertomographie als bildgebende diagnostische Methode an. Zur Abklaerung von Komplikationen bzw. des so genannten ''internal derangement'' ist die Magnetresonanztomographie zu empfehlen. (orig.)

In-plane Shear Joint Capacity of Pracast Lightweight Aggregate Concrete Elements

DEFF Research Database (Denmark)

Larsen, Henning; Goltermann, Per; Scherfig, Søren

1996-01-01

The paper establishes and documents formulas for the in-plane shear capacity between precast elements of lightweight aggregate concrete with open structure. The joints investigated are rough or toothed and have all been precracked prior to the testing in order to obtain realistic test results....... The paper documents the shear force capacity for the joint strength between the most common joint types between precast LAC roof and floor elements used in Scandinavia....

Verification of Strength of the Welded Joints by using of the Aramis Video System

Directory of Open Access Journals (Sweden)

Pała Tadeusz

2017-03-01

Full Text Available In the paper are presented the results of strength analysis for the two types of the welded joints made according to conventional and laser technologies of high-strength steel S960QC. The hardness distributions, tensile properties and fracture toughness were determined for the weld material and heat affect zone material for both types of the welded joints. Tests results shown on advantage the laser welded joints in comparison to the convention ones. Tensile properties and fracture toughness in all areas of the laser joints have a higher level than in the conventional one. The heat affect zone of the conventional welded joints is a weakness area, where the tensile properties are lower in comparison to the base material. Verification of the tensile tests, which carried out by using the Aramis video system, confirmed this assumption. The highest level of strains was observed in HAZ material and the destruction process occurred also in HAZ of the conventional welded joint.