Variation in electrical properties of gamma irradiated cadmium selenate nanowires

Energy Technology Data Exchange (ETDEWEB)

Chauhan, R.P., E-mail: chauhanrpc@gmail.com; Rana, Pallavi, E-mail: prana.phy@gmail.com; Narula, Chetna; Panchal, Suresh; Choudhary, Ritika

2016-07-15

Preparation of low-dimensional materials attracts more and more interest in the last few years, mainly due to the wide field of potential commercial applications ranging from life sciences, medicine and biotechnology to communication and electronics. One-dimensional systems are the smallest dimension structures that can be used for efficient transport of electrons and thus expected to be critical to the function and integration of nanoscale devices. Nanowires with well controlled morphology and extremely high aspect ratio can be obtained by replicating a nanoporous polymer ion-track membrane with cylindrical pores of controlled dimensions. With this technique, materials can be deposited within the pores of the membrane by electrochemical reduction of the desired ion. In the present study, cadmium selenate nanowires were synthesized potentiostatically via template method. These synthesized nanowires were then exposed to gamma rays by using a {sup 60}Co source at the Inter University Accelerator Centre, New Delhi, India. Structural, morphological, electrical and elemental characterizations were made in order to analyze the effect of gamma irradiation on the synthesized nanowires. I–V measurements of cadmium selenate nanowires, before and after irradiation were made with the help of Keithley 2400 source meter and Ecopia probe station. A significant change in the electrical conductivity of cadmium selenate nanowires was found after gamma irradiation. The crystallography of the synthesized nanowires was also studied using a Rigaku X-ray diffractrometer equipped with Cu-Kα radiation. XRD patterns of irradiated samples showed no variation in the peak positions or phase change.

Potentiometric titration of selenic and telluric acids with titanium(III) chloride in nonaqueous solvents

International Nuclear Information System (INIS)

Yoshimura, Chozo; Miyamoto, Kiyoshige

1985-01-01

Selenic and Telluric acids were titrated potentiometrically with titanium(III) chloride solution by using Pt-Cu · Hg bimetallic electrodes in nonaqueous solvents such as N, N-dimethyl-formamide (DMF), dimethyl sulfoxide (DMSO), isopropyl alcohol (IPA) and the mixtures of these solvents. It was found that selenic and telluric acids were titrated directly at room temperature in DMF solution without hydrochloric acid. The molar ratios of selenic and telluric acids to titanium(III) chloride was 1 : 6. However, the corresponding reactions to SeO 4 2- → SeO 3 2- or TeO 4 2- → TeO 3 2- were not confirmed in the titration curve in DMF. In the titration of selenic acid in mixed solvents of DMF and IPA in 1 : 1 or 1 : 2 ratio, two steps were observed. The first and the second steps were appeared on the titration curve at molar ratios of 1 : 2 and 1 : 6, respectively. It was interpreted that the first step corresponded to the intermediate reaction of SeO 4 2- → SeO 3 2- . Mixed solution of selenic and telluric acids were determined by the proposed method. Three steps were observed on the titration curve. It was interpreted that the first, second and third steps corresponded to the reaction of SeO 4 2- → SeO 3 2- , SeO 3 2- → Se(0), and TeO 4 2- → Te(0), respectively. Less than 5 % of water gave no influence on the titration. (author)

Preparation, characterization and thermal behaviour study of double selenates of lanthanides, yttrium and beryllium

International Nuclear Information System (INIS)

Ribeiro, C.A.

1988-01-01

The lanthanides (III) and yttrium (III) double selenates were studied using common analytical methods, atomic absorption, X-ray diffraction infra-red absorption, thermogravimetry and differential thermal analysis. These compounds were prepared from the mixture of lanthanides (III) and yttrium (III) selenates aqueous solution and basic beryllium selenates aqueous solution, obeying equimolar relation (1:1) to the cation

Thin film solar cells by selenization sulfurization using diethyl selenium as a selenium precursor

Science.gov (United States)

Dhere, Neelkanth G.; Kadam, Ankur A.

2009-12-15

A method of forming a CIGSS absorber layer includes the steps of providing a metal precursor, and selenizing the metal precursor using diethyl selenium to form a selenized metal precursor layer (CIGSS absorber layer). A high efficiency solar cell includes a CIGSS absorber layer formed by a process including selenizing a metal precursor using diethyl selenium to form the CIGSS absorber layer.

Two-stage neural-network-based technique for Urdu character two-dimensional shape representation, classification, and recognition

Science.gov (United States)

Megherbi, Dalila B.; Lodhi, S. M.; Boulenouar, A. J.

2001-03-01

This work is in the field of automated document processing. This work addresses the problem of representation and recognition of Urdu characters using Fourier representation and a Neural Network architecture. In particular, we show that a two-stage Neural Network scheme is used here to make classification of 36 Urdu characters into seven sub-classes namely subclasses characterized by seven proposed and defined fuzzy features specifically related to Urdu characters. We show that here Fourier Descriptors and Neural Network provide a remarkably simple way to draw definite conclusions from vague, ambiguous, noisy or imprecise information. In particular, we illustrate the concept of interest regions and describe a framing method that provides a way to make the proposed technique for Urdu characters recognition robust and invariant to scaling and translation. We also show that a given character rotation is dealt with by using the Hotelling transform. This transform is based upon the eigenvalue decomposition of the covariance matrix of an image, providing a method of determining the orientation of the major axis of an object within an image. Finally experimental results are presented to show the power and robustness of the proposed two-stage Neural Network based technique for Urdu character recognition, its fault tolerance, and high recognition accuracy.

Entwicklung und Anwendung von Methoden zur Bestimmung von Selen-Spezies in human-biologischem Material

OpenAIRE

Jäger, Thomas

2014-01-01

Selen ist essentieller Bestandteil von mehr als 25 physiologisch wichtigen menschlichen Enzymen. Der tägliche Bedarf wird überwiegend in Form von organischen Selenverbindungen wie Selenmethionin oder Selenocystein aus der Nahrung aufgenommen. Weitere Expositionswege sind die Einnahme von Nahrungsergänzungsmitteln zur Selensupplementation sowie die inhalative oder dermale Aufnahme von in erster Linie anorganischen Selenverbindungen oder elementarem Selen an Arbeitsplätzen der Selen-verarbeiten...

Studies on structural, optical, and photoelectric properties of CdS{sub 1-x}Se{sub x} films fabricated by selenization of chemical bath deposited CdS films

Energy Technology Data Exchange (ETDEWEB)

Lu, Tianyu; Gu, Han; Ge, Zhenhua; Zhang, Lei; Wang, Zhicheng; Fang, Yong; Han, Zhida; Qian, Bin; Jiang, Xuefan [Department of Physics, Changshu Institute of Technology, Changshu (China); Wu, Wangping [School of Mechanical Engineering, Changzhou University, Changzhou (China)

2017-02-15

In this paper, high-photosensitive CdS{sub 1-x}Se{sub x} films are synthesized by a two-step technique, which includes the chemical bath deposition of CdS films and a following selenization process. The structural, optical, and photoelectric properties of the CdS{sub 1-x}Se{sub x} films were investigated. With the substitution of selenium for sulfur atoms, grain sizes of the as-prepared CdS{sub 1-x}Se{sub x} films are effectively enlarged and reach the scales of the films thickness when the selenization temperature exceeds 450 C. With increasing the selenization temperature from 350 to 550 C, the band gaps of CdS{sub 1-x}Se{sub x} films gradually decrease from 2.37 to 1.82 eV. Under the co-action of the grain-size enlargement and band-gap decrease, the CdS{sub 1-x}Se{sub x} films fabricated at 450 C show very pronounced photosensitivity. Noteworthy, the ratio of photo to dark conductivity of the CdS{sub 1-x}Se{sub x} film selenized at 450 C reaches 1.1 x 10{sup 5}, suggesting a promising application potential in the photoelectric devices. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The influence of temperature on selenate adsorption by goethite

Energy Technology Data Exchange (ETDEWEB)

Kersten, M.; Vlasova, N. [Mainz Univ. (Germany). Geosciences Inst.

2013-08-01

Acid-base batch titration data up to 75 C were used to constrain a temperature-dependent 1-pK basic Stern model of the surface protonation reactions of goethite. Experimental data for the temperature dependence of pH{sub PZC} (as determined using the two-term Van't Hoff extrapolation) yielded a negative value of -44.9 kJ/mol for the surface protonation enthalpy, and therefore a shift of the zero point of charge towards lower pH values with increasing temperature. Batch titrations at selenate concentrations of between 10 and 100 {mu}M showed an increased degree of adsorption in the acidic pH range, which appeared to be sensitive to the ionic strength of the solution. The selenate adsorption edges shifted towards more acidic pH values with increasing temperature. A 1-pK charge distribution multi-site surface complexation (CD-MUSIC) model was applied, assuming the formation of an outer-spheric surface complex together with an inner-spheric one, in agreement with published spectroscopic information. The temperature behaviour of the intrinsic equilibrium constants were well represented by a linear Van't Hoff log K vs. 1/T plot, from which negative enthalpy values could be derived for both adsorption reactions. The adsorption of the selenate was therefore exothermic and became weaker with increasing temperature. The bidentate inner-spheric complex was more sensitive to rises in temperature (-70 kJ/mol), compared to the outer-spheric complex (-36 kJ/mol). The latter ultimately became the dominating adsorption process at the highest temperature studied. (orig.)

The influence of temperature on selenate adsorption by goethite

International Nuclear Information System (INIS)

Kersten, M.; Vlasova, N.

2013-01-01

Acid-base batch titration data up to 75 C were used to constrain a temperature-dependent 1-pK basic Stern model of the surface protonation reactions of goethite. Experimental data for the temperature dependence of pH PZC (as determined using the two-term Van't Hoff extrapolation) yielded a negative value of -44.9 kJ/mol for the surface protonation enthalpy, and therefore a shift of the zero point of charge towards lower pH values with increasing temperature. Batch titrations at selenate concentrations of between 10 and 100 μM showed an increased degree of adsorption in the acidic pH range, which appeared to be sensitive to the ionic strength of the solution. The selenate adsorption edges shifted towards more acidic pH values with increasing temperature. A 1-pK charge distribution multi-site surface complexation (CD-MUSIC) model was applied, assuming the formation of an outer-spheric surface complex together with an inner-spheric one, in agreement with published spectroscopic information. The temperature behaviour of the intrinsic equilibrium constants were well represented by a linear Van't Hoff log K vs. 1/T plot, from which negative enthalpy values could be derived for both adsorption reactions. The adsorption of the selenate was therefore exothermic and became weaker with increasing temperature. The bidentate inner-spheric complex was more sensitive to rises in temperature (-70 kJ/mol), compared to the outer-spheric complex (-36 kJ/mol). The latter ultimately became the dominating adsorption process at the highest temperature studied. (orig.)

Contribution of SELENE-2 geodetic measurements to constrain the lunar internal structure

Science.gov (United States)

Matsumoto, K.; Kikuchi, F.; Yamada, R.; Iwata, T.; Kono, Y.; Tsuruta, S.; Hanada, H.; Goossens, S. J.; Ishihara, Y.; Kamata, S.; Sasaki, S.

2012-12-01

Internal structure and composition of the Moon provide important clue and constraints on theories for how the Moon formed and evolved. The Apollo seismic network has contributed to the internal structure modeling. Efforts have been made to detect the lunar core from the noisy Apollo data (e.g., [1], [2]), but there is scant information about the structure below the deepest moonquakes at about 1000 km depth. On the other hand, there have been geodetic studies to infer the deep structure of the Moon. For example, LLR (Lunar Laser Ranging) data analyses detected a displacement of the lunar pole of rotation, indicating that dissipation is acting on the rotation arising from a fluid core [3]. Bayesian inversion using geodetic data (such as mass, moments of inertia, tidal Love numbers k2 and h2, and quality factor Q) also suggests a fluid core and partial melt in the lower mantle region [4]. Further improvements in determining the second-degree gravity coefficients (which will lead to better estimates of moments of inertia) and the Love number k2 will help us to better constrain the lunar internal structure. Differential VLBI (Very Long Baseline Interferometry) technique, which was used in the Japanese lunar exploration mission SELENE (Sept. 2007 - June 2009), is expected to contribute to better determining the second-degree potential Love number k2 and low-degree gravity coefficients. SELENE will be followed by the future lunar mission SELENE-2 which will carry both a lander and an orbiter. We propose to put the SELENE-type radio sources on these spacecraft in order to accurately estimate k2 and the low-degree gravity coefficients. By using the same-beam VLBI tracking technique, these parameters will be retrieved through precision orbit determination of the orbiter with respect to the lander which serves as a reference. The VLBI mission with the radio sources is currently one of the mission candidates for SELENE-2. We have conducted a preliminary simulation study on the

The simulation of lunar gravity field recovery from D-VLBI of Chang’E-1 and SELENE lunar orbiters

Science.gov (United States)

Yan, Jianguo; Ping, Jingsong; Matsumoto, K.; Li, Fei

2008-07-01

The lunar gravity field is a foundation to study the lunar interior structure, and to recover the evolution history of the Moon. It is still an open and key topic for lunar science. For above mentioned reasons, it becomes one of the important scientific objectives of recent lunar missions, such as KAGUYA (SELENE) the Japanese lunar mission and Chang’E-1, the Chinese lunar mission. The Chang’E-1 and the SELENE were successfully launched in 2007. It is estimated that these two missions can fly around the Moon longer than 6 months simultaneously. In these two missions, the Chinese new VLBI (Very Long Baseline Interferometry) network will be applied for precise orbit determination (POD) by using a differential VLBI (D-VLBI) method during the mission period. The same-beam D-VLBI technique will contribute to recover the lunar gravity field together with other conventional observables, i.e. R&RR (Range and Range Rate) and multi-way Doppler. Taking VLBI tracking conditions into consideration and using the GEODYNII/SOVLE software of GSFC/NASA/USA [Rowlands, D.D., Marshall, J.A., Mccarthy, J., et al. GEODYN II System Description, vols. 1 5. Contractor Report, Hughes STX Corp. Greenbelt, MD, 1997; Ullman, R.E. SOLVE program: mathematical formulation and guide to user input, Hughes/STX Contractor Report, Contract NAS5-31760. NASA Goddard Space Flight Center, Greenbelt, Maryland, 1994], we simulated the lunar gravity field recovering ability with and without D-VLBI between the Chang’E-1 and SELENE main satellite. The cases of overlapped flying and tracking period of 30 days, 60 days and 90 days have been analyzed, respectively. The results show that D-VLBI tracking between two lunar satellites can improve the gravity field recovery remarkably. The results and methods introduced in this paper will benefit the actual missions.

Uptake and speciation of selenium in garlic cultivated in soil amended with symbiotic fungi (mycorrhiza) and selenate

DEFF Research Database (Denmark)

Larsen, Erik Huusfeldt; Lobinski, R.; Burger-Meyer, K.

2006-01-01

The scope of the work was to investigate the influence of selenate fertilisation and the addition of symbiotic fungi (mycorrhiza) to soil on selenium and selenium species concentrations in garlic. The selenium species were extracted from garlic cultivated in experimental plots by proteolytic...... in garlic. The selenium content in garlic, which was analysed by ICP-MS, showed that addition of mycorrhiza to the natural soil increased the selenium uptake by garlic tenfold to 15 mu g g(-1) (dry mass). Fertilisation with selenate and addition of mycorrhiza strongly increased the selenium content...... of soil by mycorrhiza and/or by selenate increased the content of selenium but not the distribution of detected selenium species in garlic. Finally, the use of two-dimensional HPLC (size exclusion followed by reversed-phase) allowed the structural characterisation of gamma...

Deposition of CuIn(Se,S)2 thin films by sulfurization of selenized Cu/In alloys

International Nuclear Information System (INIS)

Sheppard, C.J.; Alberts, V.; Bekker, W.J.

2004-01-01

The relatively small band gap values (close to 1eV) of CuInSe 2 thin films limits the conversion efficiencies of completed CuInSe 2 /CdS/ZnO solar cell devices. In the case of traditional two-stage growth techniques, limited success has been achieved to increase the band gap by substituting indium with gallium. In this study, sputtered copper-indium alloys were exposed to a H 2 Se/Ar atmosphere under defined conditions in order to produce partially reacted CuInSe 2 structures. These films were subsequently exposed to a H 2 S/Ar atmosphere to produce monophasic CuIn(Se, S) 2 quaternary alloys. The homogeneous incorporation of S into CuInSe 2 led to a systematic shift in the lattice parameters and band gap of the ab- sorber films. From these studies optimum selenization/sulfurization conditions were determined for the deposition of homogeneous CuIn(Se,S) 2 thin films with an optimum band gap values between 1.15 and 1.2 eV. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Topologically and geometrically flexible structural units in seven new organically templated uranyl selenates and selenite-selenates

Science.gov (United States)

Gurzhiy, Vladislav V.; Kovrugin, Vadim M.; Tyumentseva, Olga S.; Mikhaylenko, Pavel A.; Krivovichev, Sergey V.; Tananaev, Ivan G.

2015-09-01

Single crystals of seven novel uranyl oxysalts of selenium with protonated methylamine molecules, [C2H8N]2[(UO2)(SeO4)2(H2O)] (I), [C2H8N]2[(UO2)2(SeO4)3(H2O)] (II), [C4H15N3][H3O]0.5[(UO2)2(SeO4)2.93(SeO3)0.07(H2O)](NO3)0.5 (III), [C2H8N]3[H5O2][(UO2)2(SeO4)3(H2O)2]2(H2O)5 (IV), [C2H8N]2[H3O][(UO2)3(SeO4)4(HSeO3)(H2O)](H2SeO3)0.2 (V), [C4H12N]3[H3O][(UO2)3(SeO4)5(H2O)] (VI), and [C2H8N]3(C2H7N)[(UO2)3(SeO4)4(HSeO3)(H2O)] (VII) have been prepared by isothermal evaporation from aqueous solutions. Their crystal structures have been solved by direct methods and their uranyl selenate and selenite-selenate units investigated using black-and-white graphs from the viewpoints of topology of interpolyhedral linkages and isomeric variations. The crystal structure of IV is based upon complex layers with unique topology, which has not been observed previously in uranyl selenates. Investigations of the statistics and local distribution of the U-Obr-Se bond angles demonstrates that shorter angles associate with undulations, whereas larger angles correspond to planar areas of the uranyl selenite layers.

Selenization of CIS and CIGS layers deposited by chemical spray pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Babu, B. J.; Egaas, B.; Velumani, S.

2018-03-21

Cu(In1-xGax)Se2 (CIGS) thin films with x=0 (CIS) and x=0.3 (CIGS) were prepared on Mo-coated glass substrate by using chemical spray pyrolysis at a substrate temperature of 350 degrees C, followed by selenization treatment at 550 degrees C in selenium environment under N2 gas flow. X-ray diffraction patterns of as-deposited CIGS layers on Mo showed polycrystalline chalcopyrite phase with an intense (112) plane. Splitting of (204)/(220) and (116)/(312) planes for the film with x=0.3 reveals deviation of tetragonal nature. Field emission scanning electron microscopy cross-sectional images of selenized films showed clear re-crystallization of grains. During the selenization process of the CIGS absorber, a thin interface layer of MoSe2 is formed. Line mapping of Mo/CIGS layer showed more gallium segregation at the interface of back contact resulting in band gap grading. Chemical composition and mapping of the as-deposited and selenized samples were determined by energy dispersive analysis of X-rays. This work leads to fabrication of low cost and large scale Mo/CIGS/CdS/ZnO/ZnO:Al device structure.

Inhibition of synthesis of heparan sulfate by selenate: Possible dependence on sulfation for chain polymerization

International Nuclear Information System (INIS)

Dietrich, C.P.; Nader, H.B.; Buonassisi, V.; Colburn, P.

1988-01-01

Selenate, a sulfation inhibitor, blocks the synthesis of heparan sulfate and chondroitin sulfate by cultured endothelial cells. In contrast, selenate does not affect the production of hyaluronic acid, a nonsulfated glycosaminoglycan. No differences in molecular weight, [ 3 H]glucosamine/[ 35 S]sulfuric acid ratios, or disaccharide composition were observed when the heparan sulfate synthesized by selenate-treated cells was compared with that of control cells. The absence of undersulfated chains in preparations from cultures exposed to selenate supports the concept that, in the intact cell, the polymerization of heparan sulfate might be dependent on the sulfation of the saccharide units added to the growing glycosaminoglycan chain

Scaling Equation of State for Ferroelectric Triglycine Selenate at T ≈ Tc

NARCIS (Netherlands)

Iglesias, T.; Noheda, B.; Gallego, B.; Fernández del Castillo, J.R.; Lifante, G.; Gonzalo, J.A.

1994-01-01

Digital data of polarization vs. field on triglycine selenate at closely spaced temperature intervals (ΔT ≈ 0.015) in the vicinity of the quasi-tricritical point of triglycine selenate have been collected. These data fulfill very well the scaling equation of state ê± = ±p + (1/5)p5 (where ê- and ê+

Thermal decomposition of double selenates of lanthanides (III), yttrium (III) and ammonium

International Nuclear Information System (INIS)

Crespi, M.S.

1989-01-01

Double selenates of lanthanides, yttrium and ammonium were prepared by treating mixtures of simple selenates with equimolar amounts and then dried in a vacuum desiccator containing anhydrous calcium chloride, protected from light. The compounds were studied using the conventional analytical methods such as infrared absorption spectra, X-ray diffraction, differential thermal analysis (DTA), and thermogravimetry (TG). (author)

Background electrolytes and pH effects on selenate adsorption using iron-impregnated granular activated carbon and surface binding mechanisms.

Science.gov (United States)

Zhang, Ning; Gang, Daniel Dianchen; McDonald, Louis; Lin, Lian-Shin

2018-03-01

Iron-impregnated granular activated carbon (Fe-GAC) has been shown effective for selenite adsorptive removal from aqueous solutions, but similar effectiveness was not observed with selenate. This study examined the effects of background electrolytes and pH on selenate adsorption on to Fe-GAC, and surface bindings to elucidate the selenate adsorption mechanisms. The decrease magnitude of selenate adsorption capacity under three background electrolytes followed the order: LiCl > NaCl > KCl, as ionic strength increased from 0.01 to 0.1 M. Larger adsorption capacity differences among the three electrolytes were observed under the higher ionic strengths (0.05 and 0.1 M) than those under 0.01 M. Multiplet peak fittings of high resolution X-ray photoelectron spectra for O1s and Fe2p 3/2 indicated the presence of iron (III) on adsorbent surface. pH variations during the adsorbent preparation within 3-8 in NaCl solutions did not cause appreciable changes in the iron redox state and composition. Raman spectra showed the formation of both monodentate and bidentate inner sphere complexes under pHs adsorption under alkaline conditions. Mechanisms for monodentate and bidentate formations and a stable six-member ring structure were proposed. Two strategies were recommended for modifying Fe-GAC preparation procedure to enhance the selenate adsorption: (1) mixed-metal oxide coatings to increase the point of zero charge (pH zpc ); and (2) ferrous iron coating to initially reduce selenate followed by selenite adsorption. Copyright © 2017 Elsevier Ltd. All rights reserved.

Two-Stage MAS Technique for Analysis of DRA Elements and Arrays on Finite Ground Planes

DEFF Research Database (Denmark)

Larsen, Niels Vesterdal; Breinbjerg, Olav

2007-01-01

A two-stage Method of Auxiliary Sources (MAS) technique is proposed for analysis of dielectric resonator antenna (DRA) elements and arrays on finite ground planes (FGPs). The problem is solved by first analysing the DRA on an infinite ground plane (IGP) and then using this solution to model the FGP...

Uptake and Distribution of Added Selenite and Selenate by Barley and Red Clover as Influenced by Sulphur

DEFF Research Database (Denmark)

Nielsen, Gunnar Gissel

1973-01-01

The uptake of added Se from selenite and selenate by barley and red clover was investigated in a pot experiment. Much more of selenate than of selenite was taken up but the Se concentrations in the plants declined more with time when selenate was the source. Increasing sulphate addition to the soil...

Induced membrane technique combined with two-stage internal fixation for the treatment of tibial osteomyelitis defects.

Science.gov (United States)

Luo, Fei; Wang, Xiaohua; Wang, Shulin; Fu, Jingshu; Xie, Zhao

2017-07-01

The purpose of this study was to observe the effects of induced membrane technique combined with two-stage internal fixation in the treatment of tibial osteomyelitis defects. A retrospective analyses for 67 cases of tibialosteomyelitis defects were admitted to our department between September 2012 to February 2015, which were treated with induced membrane technique. At the first stage, implanted with a PMMA cement spacer in the defects after radical debridement and fixed with reconstructive locked plate. Bone grafting and exchanged the plate with intramedullary nail at the second stage. In current study, all patients were followed up for 18-35 months. Sixty-six patients achieved bone union with the average radiographic and clinical healing times of 5.55±2.19 and 7.45±1.69months, respectively. Seven patients required a second debridement before grafting, while four patients experienced a recurrence of infection or a relapse following second stage treatment. Twelve patients experienced either knee or ankle dysfunctions and 2 patients faced delayed wound healing. Donor site complications includes pain and infection were found in 7 and 3 patients, respectively with delayed stress fracture in 1 patient only. Induced membrane technique for the treatment of tibial osteomyelitis defects, seems a reliable method. The use of reconstructive locked plate as a temporary internal fixation at the first stage and exchanged with intramedullary nail at the second stage, potentially achieves good clinical efficacy. Care should be taken to restore the joint function especially in distal tibia. Copyright © 2017 Elsevier Ltd. All rights reserved.

Changes in SeMSC, glucosinolates and sulforaphane levels, and in proteome profile in broccoli (Brassica oleracea var. Italica) fertilized with sodium selenate.

Science.gov (United States)

Sepúlveda, Ignacio; Barrientos, Herna; Mahn, Andrea; Moenne, Alejandra

2013-05-07

The aim of this work was to analyze the effect of sodium selenate fortification on the content of selenomethyl selenocysteine (SeMSC), total glucosinolates and sulforaphane, as well as the changes in protein profile of the inflorescences of broccoli (Brassica oleracea var. Italica). Two experimental groups were considered: plants treated with 100 μmol/L sodium selenate (final concentration in the pot) and control plants treated with water. Fortification began 2 weeks after transplantation and was repeated once a week during 10 weeks. Broccoli florets were harvested when they reached appropriate size. SeMSC content in broccoli florets increased significantly with sodium selenate fortification; but total glucosinolates and sulforaphane content as well as myrosinase activity were not affected. The protein profile of broccoli florets changed due to fortification with sodium selenate. Some proteins involved in general stress-responses were up-regulated, whereas down-regulated proteins were identified as proteins involved in protection against pathogens. This is the first attempt to evaluate the physiological effect of fortification with sodium selenate on broccoli at protein level. The results of this work will contribute to better understanding the metabolic processes related with selenium uptake and accumulation in broccoli.

Changes in SeMSC, Glucosinolates and Sulforaphane Levels, and in Proteome Profile in Broccoli (Brassica oleracea var. Italica Fertilized with Sodium Selenate

Directory of Open Access Journals (Sweden)

Alejandra Moenne

2013-05-01

Full Text Available The aim of this work was to analyze the effect of sodium selenate fortification on the content of selenomethyl selenocysteine (SeMSC, total glucosinolates and sulforaphane, as well as the changes in protein profile of the inflorescences of broccoli (Brassica oleracea var. Italica. Two experimental groups were considered: plants treated with 100 mmol/L sodium selenate (final concentration in the pot and control plants treated with water. Fortification began 2 weeks after transplantation and was repeated once a week during 10 weeks. Broccoli florets were harvested when they reached appropriate size. SeMSC content in broccoli florets increased significantly with sodium selenate fortification; but total glucosinolates and sulforaphane content as well as myrosinase activity were not affected. The protein profile of broccoli florets changed due to fortification with sodium selenate. Some proteins involved in general stress-responses were up-regulated, whereas down-regulated proteins were identified as proteins involved in protection against pathogens. This is the first attempt to evaluate the physiological effect of fortification with sodium selenate on broccoli at protein level. The results of this work will contribute to better understanding the metabolic processes related with selenium uptake and accumulation in broccoli.

Selen og vitamin E til svin

DEFF Research Database (Denmark)

Nielsen, H. E.; Danielsen, V.; Nielsen, Gunnar Gissel

1975-01-01

, kan der let opstå selenmangel. Vitamin E kan i nogen grad erstatte selen, men kun indenfor visse grænser. De senere års erfaringer har tydeligt vist, at der ofte opstår selenmangel, selvom der findes rigeligt E-vitamin i foderet. Resultaterne fra dette forsøg tyder på, at en nedsættelse af...

Dehydration-driven evolution of topological complexity in ethylamonium uranyl selenates

Energy Technology Data Exchange (ETDEWEB)

Gurzhiy, Vladislav V., E-mail: vladgeo17@mail.ru [Department of Crystallography, St. Petersburg State University, University Emb. 7/9, 199034 St. Petersburg (Russian Federation); Krivovichev, Sergey V. [Department of Crystallography, St. Petersburg State University, University Emb. 7/9, 199034 St. Petersburg (Russian Federation); Tananaev, Ivan G. [Far Eastern Federal University, Suhanova st. 8, 690950 Vladivostok (Russian Federation)

2017-03-15

Single crystals of four novel uranyl selenate and selenite-selenate oxysalts with protonated ethylamine molecules, (C{sub 2}H{sub 8}N){sub 2}[(UO{sub 2})(SeO{sub 4}){sub 2}(H{sub 2}O)](H{sub 2}O) (I), (C{sub 2}H{sub 8}N){sub 3}[(UO{sub 2})(SeO{sub 4}){sub 2}(HSeO{sub 4})] (II), (C{sub 2}H{sub 8}N)[(UO{sub 2})(SeO{sub 4})(HSeO{sub 3})] (III), and (C{sub 2}H{sub 8}N)(H{sub 3}O)[(UO{sub 2})(SeO{sub 4}){sub 2}(H{sub 2}O)] (IV) have been prepared by isothermal evaporation from aqueous solutions. Uranyl-containing 1D and 2D units have been investigated using topological approach and information-based complexity measurements that demonstrate the evolution of structural units and the increase of topological complexity with the decrease of H{sub 2}O content. - Graphical abstract: Single crystals of four novel uranyl selenate and selenite-selenate oxysalts with protonated ethylamine molecules have been prepared by isothermal evaporation from aqueous solutions. Structural analysis and information-based topological complexity calculations points to the possible sequence of crystalline phases formation, showing both topological and structural branches of evolution. - Highlights: • Single crystals of four novel uranyl oxysalts were prepared by evaporation method. • The graph theory was used for investigation of topologies of structural units. • Dehydration processes drives the evolution of topological complexity of 1D and 2D structural units.

Effect of selenization time on the structural and morphological properties of Cu(In,Ga)Se2 thin films absorber layers using two step growth process

Science.gov (United States)

Korir, Peter C.; Dejene, Francis B.

2018-04-01

In this work two step growth process was used to prepare Cu(In, Ga)Se2 thin film for solar cell applications. The first step involves deposition of Cu-In-Ga precursor films followed by the selenization process under vacuum using elemental selenium vapor to form Cu(In,Ga)Se2 film. The growth process was done at a fixed temperature of 515 °C for 45, 60 and 90 min to control film thickness and gallium incorporation into the absorber layer film. The X-ray diffraction (XRD) pattern confirms single-phase Cu(In,Ga)Se2 film for all the three samples and no secondary phases were observed. A shift in the diffraction peaks to higher 2θ (2 theta) values is observed for the thin films compared to that of pure CuInSe2. The surface morphology of the resulting film grown for 60 min was characterized by the presence of uniform large grain size particles, which are typical for device quality material. Photoluminescence spectra show the shifting of emission peaks to higher energies for longer duration of selenization attributed to the incorporation of more gallium into the CuInSe2 crystal structure. Electron probe microanalysis (EPMA) revealed a uniform distribution of the elements through the surface of the film. The elemental ratio of Cu/(In + Ga) and Se/Cu + In + Ga strongly depends on the selenization time. The Cu/In + Ga ratio for the 60 min film is 0.88 which is in the range of the values (0.75-0.98) for best solar cell device performances.

Modeling selenate adsorption behavior on oxides, clay minerals, and soils using the triple layer model

Science.gov (United States)

Selenate adsorption behavior was investigated on amorphous aluminum oxide, amorphous iron oxide, goethite, clay minerals: kaolinites, montmorillonites, illite, and 18 soil samples from Hawaii, and the Southwestern and the Midwestern regions of the US as a function of solution pH. Selenate adsorpti...

Effect of selenization conditions on the growth and properties of Cu2ZnSn(S,Se)4 thin films

OpenAIRE

Ranjbar, Samaneh; Rajesh Menon, M.R.; Fernandes, P.A.; da Cunha, A.F.

2015-01-01

The opto-electronic properties of copper zinc tin sulfide can be tuned to achieve better cell efficiencies by controlled incorporation of selenium. In this paper we report the growth of Cu2ZnSn(S,Se)4 (CZTSSe) using a hybrid process involving the sequential evaporation of Zn and sputtering of the sulfide precursors of Cu and Sn, followed by a selenization step. Two approaches for selenization were followed, one using a tubular furnace and the other using a rapid thermal processor. The effects...

The chemical consequences of thermal neutron capture in alkali selenates

International Nuclear Information System (INIS)

Duplatre, G.; Vargas, J.I.

1977-01-01

The initial retention of the SeO 4 2- ion after thermal neutron capture has been studied in various matrices by chemical analysis. A comparison between the thermal behaviour of the chemically analyzed Sesup(IV) and the disappearance of the E.P.R. species SeO 3 - and SeO 4 3- showed that the retention fraction would include all species with oxidation state higher or equal to VI. The retentions observed in the different matrices show the existence of four families with respective retentions of: 2.6%[K 2 SeO 4 diluted in (NH 4 ) 2 SO 4 ], 9.2% [anhydrous and hydrated Li and Ca selenates; K 2 SeO 4 diluted in NaIO 3 ; Se + implanted in K 2 SeO 4 ; Triglycine selenate], 21.5% [K 2 SeO 4 diluted in KNO 3 , K 2 SO 4 , Na 2 WO 4 and Na 2 WO 4 .2H 2 O] and 32.0% [Na,K and Cs selenates]. Whereas chemical considerations may be invoked for the (NH 4 ) 2 SO 4 matrix, a mechanical model is proposed for the three other groups. (author)

Subsurface structures in the northern Mare Imbrium measured by Chang'E-3 and SELENE

Science.gov (United States)

Kumamoto, A.; Ishiyama, K.; Feng, J.

2016-12-01

Subsurface structures in the northern Mare Imbrium measured by Chang'E-3 and SELENE have been compared. In Chang'E-3 mission, subsurface radar sounding at (19.51W, 44.12N) was performed by Lunar Penetrating Radar (LPR) onboard the Yutu rover. The LPR was pulse radar operated at two frequencies: 60 MHz and 500 MHz. During its operation period from December 2013 to January 2014, the LPR observed subsurface echoes along the rover's track with total distance of 114 m. From the observation in 60 MHz, the subsurface echoes from buried regolith layers at depths of 35, 50, 140, 240, and 360 m were reported (Xiao et al., 2015). In SELENE mission, global subsurface radar sounding of the moon was performed by Lunar Radar Sounder (LRS) onboard the SELENE (Kaguya) spacecraft from the polar orbit with an altitude of 100 km. The LRS was chirp radar operated in a frequency range from 4-6 MHz. So the range resolution of LRS was 75 m in vacuum. During operation period from December 2007 to September 2008, subsurface echoes from all areas of the Moon was observed with a lateral resolution of 76 m. From the global observation, the subsurface echoes from the buried regolith layers in the neraside maria including Mare Imbrium at depths of several hundred meters were reported (Ono et al., 2009).In the present study, we focus on SELENE/LRS data obtained at (19.50W, 44.12N) which is the nearest to the Chang'E-3 landing site. While clear and large-scale subsurface reflectors, as found in Ono et al. (2009), are not found in it, we can identify some echo components from the depths of 140 ( 2000 ns), 240 ( 4000 ns), and 360 m ( 6000 ns). Further analyses utilizing high-resolution data from Chang'E-3/LPR and large-scale data from SELENE/LRS, we will be able to determine the thickness and large-scale structures of the buried regolith layers found by the both radars, and discuss their formation processes in volcanic history of Mare Imbrium.

Two-stage implant placement technique for the management of irradiated jaws: An animal study.

Science.gov (United States)

Aboushelib, Moustafa N; Arnaout, Mohamed A; Elsafi, Mohamed H; Kassem, Youssef M

2017-10-01

Radiotherapy results in diminished bone remodeling capacity and an elevated risk of osteoradionecrosis, which can negatively influence the survival rate of dental implants. Patients receiving radiotherapy are advised not to receive dental implants during or soon after completing their radiotherapy. The purpose of this animal study was to investigate a 2-stage implant placement technique designed to diminish applied trauma on irradiated bone. Two groups of white New Zealand rabbits received radiotherapy in ascending doses (2, 4, 8 Gy), while a nonirradiated group served as control. Three weeks after completion of the last radiotherapy session, one of the irradiated groups and the control group received titanium dental implants bilaterally in the femur head. For the second irradiated group, an osteotomy was performed, and the surgical wound was left to heal for 2 weeks before implant placement. All animals were sacrificed 4 weeks after implant placement, and histomorphometric analysis was used to study bone-implant contact (n=14, α=.05). Statistical analysis revealed significantly higher (F=159, P<.001) bone-implant contact in the 2-stage (40.2 ±1.9) implant placement technique than in the immediately placed implants (21.2 ±2.3) in irradiated bone. Both of the groups had a significantly lower bone-to-implant contact ratio than the non-irradiated control (64.2 ±3.8). Within the limitations of this animal study, the 2-stage implant placement technique could be used to reduce trauma in irradiated bone and to improve wound healing around dental implants. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

SELENE - Self-Forming Extensible Lunar EVA Network, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The overall objective of this research effort (Phase I and Phase II) by Scientific Systems Company, Inc. and BBN Technologies is to develop the SELENE network --...

Study of the Cupriavidus metallidurans CH34 resistance of selenite and selenate oxy-anions: accumulation, localisation and transformation of selenium

International Nuclear Information System (INIS)

Avoscan, L.

2007-06-01

Selenium is an essential trace element for the living organisms but it is very toxic at high concentration. Selenite and selenate oxides, soluble forms, highly toxic and bio-assimilable, are the most prevalent forms in the environment. Some soil micro-organisms play a dominant role and contribute to the natural cycle of selenium. Our study model, Cupriavidus (formerly Ralstonia) metallidurans CH34, a telluric bacterium characteristic of metal-contaminated biotopes, is known to resist selenite by reducing it into elemental selenium, an insoluble and less toxic form of selenium. In order to better understand the mechanisms of selenium reduction in the bacteria, three methods of speciation were combined (XAS (XANES and EXAFS), HPLC-ICP-MS and SDS-PAGEPIXE). They were completed by the direct quantification of selenium accumulated in the bacteria. Speciation analyses highlighted the existence of two mechanisms of reduction of selenium oxides in C. metallidurans CH34. Assimilation transforms selenite and selenate into organic selenium, identified as seleno-methionine and leads to its non-specific incorporation into bacterial proteins (presence of selenious proteins). Detoxication precipitates selenite in nano-particles of elemental selenium. This way of detoxication is not set up after an exposure to selenate although it is nevertheless possible to detect elemental selenium but in very small amount compared to the exposure of selenite. Seleno-diglutathion is detected in bacteria stressed by an exposure to selenate in medium limited in sulphate. Bacteria exposed to selenite accumulate 25 times more selenium than when they are exposed to selenate. The study of mutants resistant to selenite, which do not express the membrane protein DedA, showed that the accumulation of selenium after exposure to selenite is decreased compared with the wild strain meaning probable link between the transport of selenite and the DedA protein. Finally, selenate would use the sulphate permease

Preparation of Cu{sub 2}ZnSnSe{sub 4} solar cells by low-temperature co-evaporation and following selenization

Energy Technology Data Exchange (ETDEWEB)

Gao, Chao, E-mail: chao.gao@kit.edu; Hetterich, Michael [Institute of Applied Physics, Karlsruhe Institute of Technology (KIT), 76131 Karlsruhe (Germany); Schnabel, Thomas; Abzieher, Tobias; Ahlswede, Erik [Zentrum für Sonnenenergie- und Wasserstoff-Forschung Baden-Württemberg (ZSW), 70565 Stuttgart (Germany); Powalla, Michael [Zentrum für Sonnenenergie- und Wasserstoff-Forschung Baden-Württemberg (ZSW), 70565 Stuttgart (Germany); Light Technology Institute (LTI), Karlsruhe Institute of Technology (KIT), 76131 Karlsruhe (Germany)

2016-01-04

Cu{sub 2}ZnSnSe{sub 4} (CZTSe) thin films are prepared by a two-step method which involves co-evaporation of Cu, Zn, Sn, and Se on molybdenum-coated soda-lime glass at low substrate temperature and a following selenization. Solar cells with efficiencies of up to 6.5% can be achieved. The influence of the selenium deposition rates during co-evaporation and the nitrogen pressure during selenization on the properties of the CZTSe films are investigated. It is found that these two parameters can significantly affect the morphology and crystallinity of the CZTSe films. The possible reasons for the experimental results are discussed.

Selenate as a novel ligand for keplerate chemistry. New {W72Mo60} keplerates with selenates inside the cavity.

Science.gov (United States)

Korenev, Vladimir S; Abramov, Pavel A; Vicent, Cristian; Zhdanov, Artem A; Tsygankova, Alphiya R; Sokolov, Maxim N; Fedin, Vladimir P

2015-05-21

The synthesis and characterization of three novel keplerate-type compounds containing the {W72Mo60} mixed-metal core are reported. Complexes (NH4)72[{W6O21(H2O)6}12{Mo2O4(SeO4)}30]·150H2O·6(NH4)2SeO4 (1a) and (NH4)25(NH2Me2)47[{W6O21(H2O)6}12{Mo2O4(SeO4)}30]·130H2O·3(NH4)2SeO4 (1b) were prepared by ligand substitution from the acetate anionic complex [{W6O21(H2O)5(CH3COO)0.5}12{Mo2O4(CH3COO)}30](48-) and selenate. The selenate anions in keplerate ions [{W6O21(H2O)6}12{Mo2O4(SeO4)}30](72-) are very labile and easily aquate with the formation of [{W6O21(H2O)6}12{Mo2O4}30(SeO4)20(H2O)20](52-), which was isolated as (NH4)20(NH2Me2)32[{W6O21(H2O)6}12{Mo2O4}30(SeO4)20(H2O)20]·150H2O (2) and structurally characterized. In the crystal structure of 2 selenate has several coordination modes, preferentially bonding to the {Mo2O4}(2+) units, and, additionally, to the {(W)W5} pentagonal blocks. The compounds have been characterized by elemental analysis, Raman, IR and (77)Se NMR spectroscopy, and by ESI mass spectrometry. Capillary electrophoresis was used for characterization of keplerates in solution for the first time.

Optimization of selenizing conditions for Seleno-Lentinan and its characteristics.

Science.gov (United States)

Ren, Guangming; Li, Koukou; Hu, Yang; Yu, Min; Qu, Juanjuan; Xu, Xiuhong

2015-11-01

Lentinan was successfully modified with nitric acid-sodium selenite method based on L9(3(4)) orthogonal experiments. The optimum selenizing conditions were obtained according to selenium conversion rate as follows: Lentinan of 1.0g, pH of 4.5, temperature of 70°C and sodium selenite of 1.50g. The antioxidant activity assays in vitro (DPPH, reducing power, superoxide radicals and hydroxyl radicals) proved that Lentinan had stronger antioxidant activity after selenizing. The elevations of serum alanine aminotransferase and aspartate aminotransferase, as well as the abnormal hepatic architecture, verified that oral administration of Seleno-Lentinan (SL2-1) markedly alleviated oxidative damage in the liver of mice induced by D-gal. In addition, SL2-1 significantly increased total antioxidant capacity, activities and protein expressions of catalase and glutathione peroxidase and lowered malondialdehyde levels in serum and liver. Fourier transform infrared spectroscopy analysis indicated that selenium of SL2-1 was mostly existed as the formations of OSeO, SeO and SeOC. Scanning electron microscope coupled with energy dispersive X-ray spectroscopy analysis revealed that the surface structure and elemental components of Lentinan significantly changed after selenizing. The results are instructive for the development of organic selenium-supplement resource. Copyright © 2015 Elsevier B.V. All rights reserved.

Preliminary observations on the effects of selenate on the development of the embryonic skate, Raja eglanteria

Science.gov (United States)

Conrad, G. W.; Luer, C. A.; Paulsen, A. Q.; Funderburgh, J. L.; Spooner, B. S. (Principal Investigator)

1993-01-01

Morphogenesis of the clearnose skate, Raja eglanteria, was not significantly inhibited as a result of 7 days of exposure to 1-2 mM selenate in the sea water during Days 59-69 of embryonic development (hatching would normally have occurred at 82 +/- 4 days of incubation). Although corneal transparency appeared normal in the eye, preliminary measurements of the thickness of Bowman's layer of the cornea suggested that it was significantly thinner in the corneas of embryos exposed to 1-2 mM selenate. Selenate is an ion reported to inhibit sulfation of glycosaminoglycans in connective tissue.

Growth of Cu(In,Al)(Se,S)2 thin films by selenization and sulfurization for a wide bandgap absorber

International Nuclear Information System (INIS)

Fujiwara, C.; Kawasaki, Y.; Sato, T.; Sugiyama, M.; Chichibu, S.F.

2010-01-01

Full text : Chalcopyrite structure Cu(In 1 .xAlx)(S y Se 1 -y) 2 (CIASS) alloys are attracting attention as promising candidates for the light-absorbing medium of high conversion efficiency, low cost, and lightweight solar cells. In addition, according to the wide variation in the bandgap energy (1.0-3.5eV), multiple-junction or tandem solar cells able to be fabricated using CIASS films of different compositions, x and y. In fact, several research groups have recently fabricated Cu(In,Al)Se 2 -based solar cells, and a high μ of 16.9 percent has been demonstrated. The sulfurization following selenization of Cu(In,Ga)Se2 (CIGS) films is believed to be promising for bandgap engineering of absorber material. Furthermore, it has been reported that the controlled incorporation of sulfur into CIGS films reduces the carrier recombination in the space charge region due to the deep trap states. Therefore, the sulfurization following selenization is expected to be used as a method of growth of CIASS films. However, sulfurization condition following selenization for obtaining CIASS films has not been clarified. The crystal growth of CIASS must be studied for solar cell applications. In this study, the advantages of using sulfurization for the growth of CIASS will be presented. Cu-In-Al precursors were selenized using diethylselenide (DESe) at 515-570 degrees Celsium for 60- 90 min under atmospheric pressure. The flow rates of DESe and N 2 carrier gases were 35 imol/min and 2 L/min, respectively. The films were then sulfurized at 550 degrees Celsium using S vapor. These films were characterized by SEM, EDX, XRD, and PL measurements. Using the selenization and sulfurization technique, polycrystalline Cu(In,Al)Se 2 , CuIn(Se,S) 2 , CuInS 2 films with thickness of approximately 2.0 im were formed without additional annealing. The films adhered well to the Mo/SLG substrate, which was confirmed by the peeling test. Phase separations, i.e. distinct peaks corresponding to CuInSe 2

The intensity of tyrosine nitration is associated with selenite and selenate toxicity in Brassica juncea L.

Science.gov (United States)

Molnár, Árpád; Feigl, Gábor; Trifán, Vanda; Ördög, Attila; Szőllősi, Réka; Erdei, László; Kolbert, Zsuzsanna

2018-01-01

Selenium phytotoxicity involves processes like reactive nitrogen species overproduction and nitrosative protein modifications. This study evaluates the toxicity of two selenium forms (selenite and selenate at 0µM, 20µM, 50µM and 100µM concentrations) and its correlation with protein tyrosine nitration in the organs of hydroponically grown Indian mustard (Brassica juncea L.). Selenate treatment resulted in large selenium accumulation in both Brassica organs, while selenite showed slight root-to-shoot translocation resulting in a much lower selenium accumulation in the shoot. Shoot and root growth inhibition and cell viability loss revealed that Brassica tolerates selenate better than selenite. Results also show that relative high amounts of selenium are able to accumulate in Brassica leaves without obvious visible symptoms such as chlorosis or necrosis. The more severe phytotoxicity of selenite was accompanied by more intense protein tyrosine nitration as well as alterations in nitration pattern suggesting a correlation between the degree of Se forms-induced toxicities and nitroproteome size, composition in Brassica organs. These results imply the possibility of considering protein tyrosine nitration as novel biomarker of selenium phytotoxicity, which could help the evaluation of asymptomatic selenium stress of plants. Copyright © 2017 Elsevier Inc. All rights reserved.

Gamma-radiation and isotopic effect on the critical behavior in triglycine selenate crystals

Science.gov (United States)

Kassem, M. E.; Hamed, A. E.; Abulnasr, L.; Abboudy, S.

1994-11-01

Isotopic effects in pure and γ-irradiated triglycine selenate crystals were investigated using the specific heat ( Cp) technique. The obtained results showed an interesting dependence of the critical behavior of Cp on the deuterium content. With increasing content of deuterium, the character of the phase transition changed from a second order (γ-type) to a first order transition. After γ-irradiation, the behavior of Cp around the phase transition region was essentially affected. The transition temperature, Tc, decreased and Δ Cp depressed, and the transition became broad. It was noted that the effect of γ-irradiation is opposite to the isotopic effect.

The study of complex equilibria of uranium(VI) with selenate

International Nuclear Information System (INIS)

Lubal, P.; Havel, J.

1997-01-01

Uranyl (M)-selenate (L) complex equilibria in solution were investigated by spectrophotometry in visible range and potentiometry by means of uranyl ion selective electrode. The formation ML and ML 2 species was proved and the corresponding stability constants calculated were: log β 1 = 1.57 6 ± 0.01 6 , log β 2 = 2.42 3 ± 0.01 3 (I 3.0 mol 1 -1 Na(ClO 4 , SeO 4 ) (spectrophotometry) at 298.2 K. Using potentiometry the values for infinite dilution (I → 0 mol 1 -1 ) were: log β 1 = 2.64 ± 0.01, log β 2 ≤ 3.4 at 298.2 K. Absorption spectra of the complexes were calculated and analysed by deconvolution technique. Derivative spectrophotometry for the chemical model determination has also been successfully applied. (author)

Structure, vibrations and quantum chemical investigations of hydrogen bonded complex of bis(1-hydroxy-2-methylpropan-2-aminium)selenate

Science.gov (United States)

Thirunarayanan, S.; Arjunan, V.; Marchewka, M. K.; Mohan, S.

2017-04-01

The hydrogen bonded molecular complex bis(1-hydroxy-2-methylpropan-2-aminium)selenate (C8H24N2O6Se) has been prepared by the reaction of 2-amino-2-methyl propanol and selenic acid. The X-ray diffraction analysis revealed that the intermolecular proton transfer from selenic acid (SeO4H2) to 2-amino-2-methylpropanol results in the formation of bis(1-hydroxy-2-methylpropan-2-aminium)selenate (HMPAS) salt and the fragments are connected through H-bonding and ion pairing. The N-H⋯O and O-H⋯O interactions between 2-amino-2-methylpropanol and selenic acid determine the supramolecular arrangement in three-dimensional space. The salt crystallises in the space group P121/n1 of monoclinic system. The complete vibrational assignments of HMPAS have been performed by FTIR and FT-Raman spectroscopy. The experimental data are correlated with the structural properties namely the energy, thermodynamic parameters, atomic charges, hybridization concepts and vibrational frequencies determined by quantum chemical studies performed with B3LYP method using 6-311++G*, 6-31+G* and 6-31G** basis sets.

Global Lunar Gravity Field Determination Using Historical and Recent Tracking Data in Preparation for SELENE

Science.gov (United States)

Goossens, S.; Matsumoto, K.; Namiki, N.; Hanada, H.; Iwata, T.; Tsuruta, S.; Kawano, N.; Sasaki, S.

2006-12-01

In the near future, a number of satellite missions are planned to be launched to the Moon. These missions include initiatives by China, India, the USA, as well as the Japanese SELENE mission. These missions will gather a wealth of lunar data which will improve the knowledge of the Moon. One of the main topics to be addressed will be the lunar gravity field. Especially SELENE will contribute to improving the knowledge of the gravity field, by applying 4-way Doppler tracking between the main satellite and a relay satellite, and by applying a separate differential VLBI experiment. These will improve the determination of the global gravity field, especially over the far side and at the lower degrees (mostly for degrees lower than 30), as is shown by extensive simulations of the SELENE mission. This work focuses on the determination of the global lunar gravity field from all available tracking data to this date. In preparation for the SELENE mission, analysis using Lunar Prospector tracking data, as well as Clementine data and historical data from the Apollo and Lunar Orbiter projects is being conducted at NAOJ. Some SMART-1 tracking data are also included. The goal is to combine the good-quality data from the existing lunar missions up to this date with the tracking data from SELENE in order to derive a new lunar gravity field model. The focus therefore currently lies on processing the available data and extracting lunar gravity field information from them. It is shown that the historical tracking data contribute especially to the lower degrees of the global lunar gravity field model. Due to the large gap in tracking data coverage over the far side for the historical data, the higher degrees are almost fully determined by the a priori information in the form of a Kaula rule. The combination with SELENE data is thus expected to improve the estimate for the lower degrees even further, including coverage of the far side. Since historical tracking data are from orbits with

Gamma-radiation and isotopic effect on the critical behavior in triglycine selenate crystals

International Nuclear Information System (INIS)

Kassem, M.E.; Hamed, A.E.; Abulnasr, L.; Abboudy, S.

1994-01-01

Isotopic effects in pure and γ-irradiated triglycine selenate crystals were investigated using the specific heat (C p ) technique. The obtained results showed an interesting dependence of the critical behavior of C p on the deuterium content. With increasing content of deuterium, the character of the phase transition changed from a second order (λ-type) to a first order transition. After γ-irradiation, the behavior of C p around the phase transition region was essentially affected. The transition temperature, T c , decreased and ΔC p depressed, and the transition became broad. It was noted that the effect of γ-irradiation is opposite to the isotopic effect. (author)

Optimum Exploration for the Self-Ordering of Anodic Porous Alumina Formed via Selenic Acid Anodizing

OpenAIRE

Akiya, Shunta; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O.

2015-01-01

Improvements of the regularity of the arrangement of anodic porous alumina formed by selenic acid anodizing were investigated under various operating conditions. The oxide burning voltage increased with the stirring rate of the selenic acid solution, and the high applied voltage without oxide burning was achieved by vigorously stirring the solution. The regularity of the porous alumina was improved as the anodizing time and surface flatness increased. Conversely, the purity of the 99.5–99.999...

Uptake and speciation of selenium in garlic cultivated in soil amended with symbiotic fungi (mycorrhiza) and selenate

Energy Technology Data Exchange (ETDEWEB)

Larsen, Erik H.; Hansen, Marianne; Rasmussen, Peter Have; Sloth, Jens J. [Danish Institute for Food and Veterinary Research, Department of Food Chemistry, Soeborg (Denmark); Lobinski, Ryszard; Ruzik, Rafal; Mazurowska, Lena [CNRS UMR 5034, Pau (France); Warsaw University of Technology, Department of Analytical Chemistry, Warsaw (Poland); Burger-Meyer, Karin; Scholten, Olga [Wageningen University and Research Centre, Plant Research International (PRI), P.O. Box 16, Wageningen (Netherlands); Kik, Chris [Wageningen University and Research Centre, Plant Research International (PRI), P.O. Box 16, Wageningen (Netherlands); Wageningen University and Research Centre, Centre for Genetic Resources, The Netherlands (CGN), P.O. Box 16, Wageningen (Netherlands)

2006-07-15

The scope of the work was to investigate the influence of selenate fertilisation and the addition of symbiotic fungi (mycorrhiza) to soil on selenium and selenium species concentrations in garlic. The selenium species were extracted from garlic cultivated in experimental plots by proteolytic enzymes, which ensured liberation of selenium species contained in peptides or proteins. Separate extractions using an aqueous solution of enzyme-deactivating hydroxylamine hydrochloride counteracted the possible degradation of labile selenium species by enzymes (such as alliinase) that occur naturally in garlic. The selenium content in garlic, which was analysed by ICP-MS, showed that addition of mycorrhiza to the natural soil increased the selenium uptake by garlic tenfold to 15 {mu}g g{sup -1} (dry mass). Fertilisation with selenate and addition of mycorrhiza strongly increased the selenium content in garlic to around one part per thousand. The parallel analysis of the sample extracts by cation exchange and reversed-phase HPLC with ICP-MS detection showed that {gamma}-glutamyl-Se-methyl-selenocysteine amounted to 2/3, whereas methylselenocysteine, selenomethionine and selenate each amounted to a few percent of the total chromatographed selenium in all garlic samples. Se-allyl-selenocysteine and Se-propyl-selenocysteine, which are selenium analogues of biologically active sulfur-containing amino acids known to occur in garlic, were searched for but not detected in any of the extracts. The amendment of soil by mycorrhiza and/or by selenate increased the content of selenium but not the distribution of detected selenium species in garlic. Finally, the use of two-dimensional HPLC (size exclusion followed by reversed-phase) allowed the structural characterisation of {gamma}-glutamyl-Se-methyl-selenocysteine and {gamma}-glutamyl-Se-methyl-selenomethionine in isolated chromatographic fractions by quadrupole time-of-flight mass spectrometry. (orig.)

Lingual mucosal graft two-stage Bracka technique for redo hypospadias repair

Directory of Open Access Journals (Sweden)

Ahmed Sakr

2017-09-01

Conclusion: Lingual mucosa is a reliable and versatile graft material in the armamentarium of two-stage Bracka hypospadias repair with the merits of easy harvesting and minor donor-site complications.

Comparative effectiveness of one-stage versus two-stage basilic vein transposition arteriovenous fistulas.

Science.gov (United States)

Ghaffarian, Amir A; Griffin, Claire L; Kraiss, Larry W; Sarfati, Mark R; Brooke, Benjamin S

2018-02-01

Basilic vein transposition (BVT) fistulas may be performed as either a one-stage or two-stage operation, although there is debate as to which technique is superior. This study was designed to evaluate the comparative clinical efficacy and cost-effectiveness of one-stage vs two-stage BVT. We identified all patients at a single large academic hospital who had undergone creation of either a one-stage or two-stage BVT between January 2007 and January 2015. Data evaluated included patient demographics, comorbidities, medication use, reasons for abandonment, and interventions performed to maintain patency. Costs were derived from the literature, and effectiveness was expressed in quality-adjusted life-years (QALYs). We analyzed primary and secondary functional patency outcomes as well as survival during follow-up between one-stage and two-stage BVT procedures using multivariate Cox proportional hazards models and Kaplan-Meier analysis with log-rank tests. The incremental cost-effectiveness ratio was used to determine cost savings. We identified 131 patients in whom 57 (44%) one-stage BVT and 74 (56%) two-stage BVT fistulas were created among 8 different vascular surgeons during the study period that each performed both procedures. There was no significant difference in the mean age, male gender, white race, diabetes, coronary disease, or medication profile among patients undergoing one- vs two-stage BVT. After fistula transposition, the median follow-up time was 8.3 months (interquartile range, 3-21 months). Primary patency rates of one-stage BVT were 56% at 12-month follow-up, whereas primary patency rates of two-stage BVT were 72% at 12-month follow-up. Patients undergoing two-stage BVT also had significantly higher rates of secondary functional patency at 12 months (57% for one-stage BVT vs 80% for two-stage BVT) and 24 months (44% for one-stage BVT vs 73% for two-stage BVT) of follow-up (P < .001 using log-rank test). However, there was no significant difference

Gamma-radiation and isotopic effect on the critical behavior in triglycine selenate crystals

Energy Technology Data Exchange (ETDEWEB)

Kassem, M.E.; Hamed, A.E.; Abulnasr, L.; Abboudy, S. [Alexandria Univ. (Egypt). Dept. of Physics

1994-11-01

Isotopic effects in pure and {gamma}-irradiated triglycine selenate crystals were investigated using the specific heat (C{sub p}) technique. The obtained results showed an interesting dependence of the critical behavior of C{sub p} on the deuterium content. With increasing content of deuterium, the character of the phase transition changed from a second order ({lambda}-type) to a first order transition. After {gamma}-irradiation, the behavior of C{sub p} around the phase transition region was essentially affected. The transition temperature, T{sub c}, decreased and {Delta}C{sub p} depressed, and the transition became broad. It was noted that the effect of {gamma}-irradiation is opposite to the isotopic effect. (author).

Identifying the Impact of E-Selen on the Sterile Medfly Ceratitis capitata at the Genomic Level Using DNA Profile

International Nuclear Information System (INIS)

Zaghloul, Y.S.

2014-01-01

The antioxidant E-Selen is an exogenous antioxidant containing both selenium and vitamin E. It was added to the larval artificial diets of the Mediterranean fruit fly, Ceratitis capitata in various concentrations (0.1, 0.3, 0.5 and 1.5 mg) prior to irradiation in order to obtain fully competent males. The produced full grown pupae were exposed to gamma rays at a dose rate of 90 Gy. Biological assessment of two E-Selen concentrations 0.3 and 0.5 mg were found to ameliorate the fitness of the sterile insects as well as to increase significantly most of their amino acids content. The study of the PCR patterns of normal and irradiated C. capitata undertaken or not different doses of E-Selen prior to irradiation and contained in the larval diets induced some modifications to the DNA profiles. The appearance of some new bands and disappearance of others were frequently encountered during this investigation. The appearance of bands was attributed to a repair mechanism that occurs in the irradiated DNA. However, the similarity in the DNA patterns of the homogenate pupal of C. capitata was due to the irradiation-induced damage may be in genome regions other than the regions of study

Single-staged vs. two-staged implant placement using bone ring technique in vertically deficient alveolar ridges - Part 1: histomorphometric and micro-CT analysis.

Science.gov (United States)

Nakahara, Ken; Haga-Tsujimura, Maiko; Sawada, Kosaku; Kobayashi, Eizaburo; Mottini, Matthias; Schaller, Benoit; Saulacic, Nikola

2016-11-01

Simultaneous implant placement with bone grafting shortens the overall treatment period, but might lead to the peri-implant bone loss or even implant failure. The aim of this study was to compare the single-staged to two-staged implant placement using the bone ring technique. Four standardized alveolar bone defects were made in the mandibles of nine dogs. Dental implants (Straumann BL ® , Basel, Switzerland) were inserted simultaneously with bone ring technique in test group and after 6 months of healing period in control group. Animals of both groups were euthanized at 3 and 6 months of osseointegration period. The harvested samples were analyzed by means of histology and micro-CT. The amount of residual bone decreased while the amount of new bone increased up to 9 months of healing period. All morphometric parameters remained stable between 3 and 6 months of osseointegration period within groups. Per a given time point, median area of residual bone graft was higher in test group and area of new bone in control group. The volume of bone ring was greater in test than in control group, reaching the significance at 6 months of osseointegration period (P = 0.002). In the present type of bone defect, single-staged implant placement may be potentially useful to shorten an overall treatment period. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Two-Stage Tissue-Expander Breast Reconstruction: A Focus on the Surgical Technique

Directory of Open Access Journals (Sweden)

Elisa Bellini

2017-01-01

Full Text Available Objective. Breast cancer, the most common malignancy in women, comprises 18% of all female cancers. Mastectomy is an essential intervention to save lives, but it can destroy one’s body image, causing both physical and psychological trauma. Reconstruction is an important step in restoring patient quality of life after the mutilating treatment. Material and Methods. Tissue expanders and implants are now commonly used in breast reconstruction. Autologous reconstruction allows a better aesthetic result; however, many patients prefer implant reconstruction due to the shorter operation time and lack of donor site morbidity. Moreover, this reconstruction strategy is safe and can be performed in patients with multiple health problems. Tissue-expander reconstruction is conventionally performed as a two-stage procedure starting immediately after mammary gland removal. Results. Mastectomy is a destructive but essential intervention for women with breast cancer. Tissue expansion breast reconstruction is a safe, reliable, and efficacious procedure with considerable psychological benefits since it provides a healthy body image. Conclusion. This article focuses on this surgical technique and how to achieve the best reconstruction possible.

Investigation into the dehydration of selenate doped Na2M(SO4)2·2H2O (M = Mn, Fe, Co and Ni): Stabilisation of the high Na content alluaudite phases Na3M1.5(SO4)3-1.5x(SeO4)1.5x (M = Mn, Co and Ni) through selenate incorporation

Science.gov (United States)

Driscoll, L. L.; Kendrick, E.; Knight, K. S.; Wright, A. J.; Slater, P. R.

2018-02-01

In this paper we report an investigation into the phases formed on dehydration of Na2M(SO4)2-x(SeO4)x·2H2O (0 ≤ x ≤ 1; M = Mn, Fe, Co and Ni). For the Fe series, all attempts to dehydrate the samples doped with selenate resulted in amorphous products, and it is suspected that a side redox reaction involving the Fe and selenate may be occurring leading to phase decomposition and hence the lack of a crystalline product on dehydration. For M = Mn, Co, Ni, the structure observed was shown to depend upon the transition metal cation and level of selenate doping. An alluaudite phase, Na3M1.5(SO4)3-1.5x(SeO4)1.5x, was observed for the selenate doped compositions, with this phase forming as a single phase for x ≥ 0.5 M = Co, and x = 1.0 M = Ni. For M = Mn, the alluaudite structure is obtained across the series, albeit with small impurities for lower selenate content samples. Although the alluaudite-type phases Na2+2y(Mn/Co)2-y(SO4)3 have recently been reported [1,2], doping with selenate appears to increase the maximum sodium content within the structure. Moreover, the selenate doped Ni based samples reported here are the first examples of a Ni sulfate/selenate containing system exhibiting the alluaudite structure.

An Effective Technique for Endoscopic Resection of Advanced Stage Angiofibroma

Science.gov (United States)

Mohammadi Ardehali, Mojtaba; Samimi, Seyyed Hadi; Bakhshaee, Mehdi

2014-01-01

Introduction: In recent years, the surgical management of angiofibroma has been greatly influenced by the use of endoscopic techniques. However, large tumors that extend into difficult anatomic sites present major challenges for management by either endoscopy or an open-surgery approach which needs new technique for the complete en block resection. Materials and Methods: In a prospective observational study we developed an endoscopic transnasal technique for the resection of angiofibroma via pushing and pulling the mass with 1/100000 soaked adrenalin tampons. Thirty two patients were treated using this endoscopic technique over 7 years. The mean follow-up period was 36 months. The main outcomes measured were tumor staging, average blood loss, complications, length of hospitalization, and residual and/or recurrence rate of the tumor. Results: According to the Radkowski staging, 23,5, and 4 patients were at stage IIC, IIIA, and IIIB, respectively. Twenty five patients were operated on exclusively via transnasal endoscopy while 7 patients were managed using endoscopy-assisted open-surgery techniques. Mean blood loss in patients was 1261± 893 cc. The recurrence rate was 21.88% (7 cases) at two years following surgery. Mean hospitalization time was 3.56 ± 0.6 days. Conclusion: Using this effective technique, endoscopic removal of more highly advanced angiofibroma is possible. Better visualization, less intraoperative blood loss, lower rates of complication and recurrence, and shorter hospitalization time are some of the advantages. PMID:24505571

An Effective Technique for Endoscopic Resection of Advanced Stage Angiofibroma

Directory of Open Access Journals (Sweden)

Mojtaba Mohammadi Ardehali

2014-01-01

Full Text Available Introduction: In recent years, the surgical management of angiofibroma has been greatly influenced by the use of endoscopic techniques. However, large tumors that extend into difficult anatomic sites present major challenges for management by either endoscopy or an open-surgery approach which needs new technique for the complete en block resection.   Materials and Methods: In a prospective observational study we developed an endoscopic transnasal technique for the resection of angiofibroma via pushing and pulling the mass with 1/100000 soaked adrenalin tampons. Thirty two patients were treated using this endoscopic technique over 7 years. The mean follow-up period was 36 months. The main outcomes measured were tumor staging, average blood loss, complications, length of hospitalization, and residual and/or recurrence rate of the tumor.   Results: According to the Radkowski staging, 23,5, and 4 patients were at stage IIC, IIIA, and IIIB, respectively. Twenty five patients were operated on exclusively via transnasal endoscopy while 7 patients were managed using endoscopy-assisted open-surgery techniques. Mean blood loss in patients was 1261± 893 cc. The recurrence rate was 21.88% (7 cases at two years following surgery. Mean hospitalization time was 3.56 ± 0.6 days.   Conclusion:  Using this effective technique, endoscopic removal of more highly advanced angiofibroma is possible. Better visualization, less intraoperative blood loss, lower rates of complication and recurrence, and shorter hospitalization time are some of the advantages.

Determination of selenite and selenate in human urine by ion chromatography and inductively coupled plasma mass spectrometry

DEFF Research Database (Denmark)

Gammelgaard, Bente; Jons, O.

2000-01-01

The selenium species selenite, selenate and selenomethionine were separated in aqueous solution by ion chromatography. The separation was performed on an IonPac AG11 in series with an AS11 anion exchange column by elution with 25 mM sodium hydroxide in 2% methanol. The Se-78 and Se-82 isotopes were...... monitored in the inductively coupled plasma mass spectrometry (ICP-MS) detector. When the chromatographic system was applied to analysis of urine samples diluted 1 + 1, the selenomethionine signal appeared in the front together with other unresolved selenium species, while the selenite and selenate signals...... and selenate, respectively, corresponding to absolute amounts of 8 and 16 pg, respectively. Calculations were based on peak height measurements of the Se-82 isotope. In 23 analysed urine samples, the concentration of selenite was in the range selenium...

Novel in situ resistance measurement for the investigation of CIGS growth in a selenization process

International Nuclear Information System (INIS)

Liu Wei; He Qing; Li Fengyan; Li Changjian; Sun Yun; Tian Jianguo; Li Zubin

2009-01-01

During the selenization process of CIGS thin films, the relation between the element loss rate and the precursor depositions are analyzed. The growth of the CIGS thin films during the selenization process is investigated by the novel in situ resistance measurement, by which the formation of compound semiconductors can be observed directly and simultaneously. Their structures, phase evolutions and element losses are analyzed by XRD and XRF. Based on the experimental results, it can be concluded that the phase transforms have nothing to do with the deposition sequences of precursors, while the element loss rates are related to the deposition sequences in this process. In addition, element loss mechanisms of CIGS thin films prepared by the selenization process are analyzed by the phase evolutions and chemical combined path in the In, Ga–Se reaction processes. Moreover it is verified that the element losses are depressed by increasing the ramping-up rate finally. The results provide effective methods to fabricate high-quality CIGS thin films with low element losses

Novel in situ resistance measurement for the investigation of CIGS growth in a selenization process

Science.gov (United States)

Liu, Wei; Tian, Jian-Guo; Li, Zu-Bin; He, Qing; Li, Feng-Yan; Li, Chang-Jian; Sun, Yun

2009-03-01

During the selenization process of CIGS thin films, the relation between the element loss rate and the precursor depositions are analyzed. The growth of the CIGS thin films during the selenization process is investigated by the novel in situ resistance measurement, by which the formation of compound semiconductors can be observed directly and simultaneously. Their structures, phase evolutions and element losses are analyzed by XRD and XRF. Based on the experimental results, it can be concluded that the phase transforms have nothing to do with the deposition sequences of precursors, while the element loss rates are related to the deposition sequences in this process. In addition, element loss mechanisms of CIGS thin films prepared by the selenization process are analyzed by the phase evolutions and chemical combined path in the In, Ga-Se reaction processes. Moreover it is verified that the element losses are depressed by increasing the ramping-up rate finally. The results provide effective methods to fabricate high-quality CIGS thin films with low element losses.

Selenate reduction to elemental selenium by anaerobic bacteria in sediments and culture: biogeochemical significance of a novel, sulfate-independent respiration

Science.gov (United States)

Oremland, Ronald S.; Hollibaugh, James T.; Maest, Ann S.; Presser, Theresa S.; Miller, Laurence G.; Culbertson, Charles W.

1989-01-01

Interstitial water profiles of SeO42−, SeO32−, SO42−, and Cl− in anoxic sediments indicated removal of the seleno-oxyanions by a near-surface process unrelated to sulfate reduction. In sediment slurry experiments, a complete reductive removal of SeO42− occurred under anaerobic conditions, was more rapid with H2 or acetate, and was inhibited by O2, NO3−, MnO2, or autoclaving but not by SO42− or FeOOH. Oxidation of acetate in sediments could be coupled to selenate but not to molybdate. Reduction of selenate to elemental selenium was determined to be the mechanism for loss from solution. Selenate reduction was inhibited by tungstate and chromate but not by molybdate. A small quantity of the elemental selenium precipitated into sediments from solution could be resolublized by oxidation with either nitrate or FeOOH, but not with MnO2. A bacterium isolated from estuarine sediments demonstrated selenate-dependent growth on acetate, forming elemental selenium and carbon dioxide as respiratory end products. These results indicate that dissimilatory selenate reduction to elemental selenium is the major sink for selenium oxyanions in anoxic sediments. In addition, they suggest application as a treatment process for removing selenium oxyanions from wastewaters and also offer an explanation for the presence of selenite in oxic waters.

Optical and structural properties of FeSe2 thin films obtained by selenization of sprayed amorphous iron oxide films

International Nuclear Information System (INIS)

Ouertani, B.; Ouerfelli, J.; Saadoun, M.; Zribi, M.; Rabha, M.Ben; Bessais, B.; Ezzaouia, H.

2006-01-01

We report in this work the optical and structural properties of iron diselenide films (FeSe 2 ) obtained by selenization under vacuum of amorphous iron oxide films predeposited by spray pyrolysis. The structure of the FeSe 2 films was investigated by scanning electron microscopy (SEM), microprobe analyses, atomic force microscopy (AFM) and X-ray diffraction (XRD). XRD and micro-probe analyses showed that FeSe 2 as well as FeSe 2-x phases begin to appear at a selenization temperature of 500 deg. C. As the selenization temperature rises, the iron diselenide films become more stoichiometric with a dominance of the FeSe 2 phase. At 550 deg. C, a single FeSe 2 phase having good crystallinity was obtained. At 600 deg. C, two phases were detected: the major one corresponds to Fe 3 O 4 , and the minor one to FeSe 2 . SEM surface views show that FeSe 2 films have granular structure with small spherical crystallites. However, layered and clustered FeSe 2 films were found, respectively, at 550 deg. C and 600 deg. C. Absorption measurements show that iron diselenide films have a direct and an indirect gaps of about 1.03 eV and 0.3 eV, which were suggested to be due to the stoichiometric FeSe 2 phase and to a Fe-rich non-stoichiometric phase, respectively

Separation of selenium compounds by CE-ICP-MS in dynamically coated capillaries applied to selenized yeast samples

DEFF Research Database (Denmark)

Bendahl, Lars; Gammelgaard, Bente

2004-01-01

The selenium species in nutritional supplement tablets, based on selenized yeast, were separated by capillary zone electrophoresis using capillaries coated dynamically with poly(vinyl sulfonate) and detected by ICP-MS. Sample pre-treatment consisted of cold-water extraction by sonication and subs......The selenium species in nutritional supplement tablets, based on selenized yeast, were separated by capillary zone electrophoresis using capillaries coated dynamically with poly(vinyl sulfonate) and detected by ICP-MS. Sample pre-treatment consisted of cold-water extraction by sonication...

A Comprehensive Study of One-Step Selenization Process for Cu(In1-x Ga x )Se2 Thin Film Solar Cells.

Science.gov (United States)

Chen, Shih-Chen; Wang, Sheng-Wen; Kuo, Shou-Yi; Juang, Jenh-Yih; Lee, Po-Tsung; Luo, Chih Wei; Wu, Kaung-Hsiung; Kuo, Hao-Chung

2017-12-01

In this work, aiming at developing a rapid and environmental-friendly process for fabricating CuIn 1-x Ga x Se 2 (CIGS) solar cells, we demonstrated the one-step selenization process by using selenium vapor as the atmospheric gas instead of the commonly used H 2 Se gas. The photoluminescence (PL) characteristics indicate that there exists an optimal location with superior crystalline quality in the CIGS thin films obtained by one-step selenization. The energy dispersive spectroscopy (EDS) reveals that the Ga lateral distribution in the one-step selenized CIGS thin film is intimately correlated to the blue-shifted PL spectra. The surface morphologies examined by scanning electron microscope (SEM) further suggested that voids and binary phase commonly existing in CIGS films could be successfully eliminated by the present one-step selenization process. The agglomeration phenomenon attributable to the formation of MoSe 2 layer was also observed. Due to the significant microstructural improvement, the current-voltage (J-V) characteristics and external quantum efficiency (EQE) of the devices made of the present CIGS films have exhibited the remarkable carrier transportation characteristics and photon utilization at the optimal location, resulting in a high conversion efficiency of 11.28%. Correlations between the defect states and device performance of the one-step selenized CIGS thin film were convincingly delineated by femtosecond pump-probe spectroscopy.

One-stage versus two-stage exchange arthroplasty for infected total knee arthroplasty: a systematic review.

Science.gov (United States)

Nagra, Navraj S; Hamilton, Thomas W; Ganatra, Sameer; Murray, David W; Pandit, Hemant

2016-10-01

Infection complicating total knee arthroplasty (TKA) has serious implications. Traditionally the debate on whether one- or two-stage exchange arthroplasty is the optimum management of infected TKA has favoured two-stage procedures; however, a paradigm shift in opinion is emerging. This study aimed to establish whether current evidence supports one-stage revision for managing infected TKA based on reinfection rates and functional outcomes post-surgery. MEDLINE/PubMed and CENTRAL databases were reviewed for studies that compared one- and two-stage exchange arthroplasty TKA in more than ten patients with a minimum 2-year follow-up. From an initial sample of 796, five cohort studies with a total of 231 patients (46 single-stage/185 two-stage; median patient age 66 years, range 61-71 years) met inclusion criteria. Overall, there were no significant differences in risk of reinfection following one- or two-stage exchange arthroplasty (OR -0.06, 95 % confidence interval -0.13, 0.01). Subgroup analysis revealed that in studies published since 2000, one-stage procedures have a significantly lower reinfection rate. One study investigated functional outcomes and reported that one-stage surgery was associated with superior functional outcomes. Scarcity of data, inconsistent study designs, surgical technique and antibiotic regime disparities limit recommendations that can be made. Recent studies suggest one-stage exchange arthroplasty may provide superior outcomes, including lower reinfection rates and superior function, in select patients. Clinically, for some patients, one-stage exchange arthroplasty may represent optimum treatment; however, patient selection criteria and key components of surgical and post-operative anti-microbial management remain to be defined. III.

Removal of trichloroethylene (TCE) contaminated soil using a two-stage anaerobic-aerobic composting technique.

Science.gov (United States)

Ponza, Supat; Parkpian, Preeda; Polprasert, Chongrak; Shrestha, Rajendra P; Jugsujinda, Aroon

2010-01-01

The effect of organic carbon addition on remediation of trichloroethylene (TCE) contaminated clay soil was investigated using a two stage anaerobic-aerobic composting system. TCE removal rate and processes involved were determined. Uncontaminated clay soil was treated with composting materials (dried cow manure, rice husk and cane molasses) to represent carbon based treatments (5%, 10% and 20% OC). All treatments were spiked with TCE at 1,000 mg TCE/kg DW and incubated under anaerobic and mesophillic condition (35 degrees C) for 8 weeks followed by continuous aerobic condition for another 6 weeks. TCE dissipation, its metabolites and biogas composition were measured throughout the experimental period. Results show that TCE degradation depended upon the amount of organic carbon (OC) contained within the composting treatments/matrices. The highest TCE removal percentage (97%) and rate (75.06 micro Mole/kg DW/day) were obtained from a treatment of 10% OC composting matrices as compared to 87% and 27.75 micro Mole/kg DW/day for 20% OC, and 83% and 38.08 micro Mole/kg DW/day for soil control treatment. TCE removal rate was first order reaction kinetics. Highest degradation rate constant (k(1) = 0.035 day(- 1)) was also obtained from the 10% OC treatment, followed by 20% OC (k(1) = 0.026 day(- 1)) and 5% OC or soil control treatment (k(1) = 0.023 day(- 1)). The half-life was 20, 27 and 30 days, respectively. The overall results suggest that sequential two stages anaerobic-aerobic composting technique has potential for remediation of TCE in heavy texture soil, providing that easily biodegradable source of organic carbon is present.

Detection of over 100 selenium metabolites in selenized yeast by liquid chromatography electrospray time-of-flight mass spectrometry.

Science.gov (United States)

Gilbert-López, Bienvenida; Dernovics, Mihaly; Moreno-González, David; Molina-Díaz, Antonio; García-Reyes, Juan F

2017-08-15

The characterization of the selenometabolome of Selenized(Se)-yeast, that is the fraction of water soluble low-molecular weight Se-metabolites produced in Se-yeast is of paramount interest to expand the knowledge on the composition of this food supplement. In this work, we have applied liquid chromatography electrospray time-of-flight mass spectrometry (LC-TOFMS) to search for Se-species from the low molecular weight range fraction of the selenized yeast used for food supplements. Prior to LC-TOFMS, sample treatment consisted of ultrasound assisted water extraction followed by size exclusion fractionation assisted with off-line inductively coupled plasma mass spectrometry detection of isotope 82 Se. The fraction corresponding to low-molecular weight species was subjected to LC-TOFMS using electrospray ionization in the positive ion mode. The detection of the suspected selenized species has been based on the information obtained from accurate mass measurements of both the protonated molecules and fragments from in-source CID fragmentation; along with the characteristic isotope pattern exhibited by the presence of Se. The approach enables the detection of 103 selenized species, most of them not previously reported, in the range from ca. 300-650Da. Besides the detection of selenium species, related sulphur derivate metabolites were detected based on the accurate mass shift due to the substitution of sulphur and selenium. Copyright © 2017. Published by Elsevier B.V.

Comparison of Oone-Stage Free Gracilis Muscle Flap With Two-Stage Method in Chronic Facial Palsy

Directory of Open Access Journals (Sweden)

J Ghaffari

2007-08-01

Full Text Available Background:Rehabilitation of facial paralysis is one of the greatest challenges faced by reconstructive surgeons today. The traditional method for treatment of patients with facial palsy is the two-stage free gracilis flap which has a long latency period of between the two stages of surgery.Methods: In this paper, we prospectively compared the results of the one-stage gracilis flap method with the two -stage technique.Results:Out of 41 patients with facial palsy refered to Hazrat-e-Fatemeh Hospital 31 were selected from whom 22 underwent two- stage and 9 one-stage method treatment. The two groups were identical according to age,sex,intensity of illness, duration, and chronicity of illness. Mean duration of follow up was 37 months. There was no significant relation between the two groups regarding the symmetry of face in repose, smiling, whistling and nasolabial folds. Frequency of complications was equal in both groups. The postoperative surgeons and patients' satisfaction were equal in both groups. There was no significant difference between the mean excursion of muscle flap in one-stage (9.8 mm and two-stage groups (8.9 mm. The ratio of contraction of the affected side compared to the normal side was similar in both groups. The mean time of the initial contraction of the muscle flap in the one-stage group (5.5 months had a significant difference (P=0.001 with the two-stage one (6.5 months.The study revealed a highly significant difference (P=0.0001 between the mean waiting period from the first operation to the beginning of muscle contraction in one-stage(5.5 monthsand two-stage groups(17.1 months.Conclusion:It seems that the results and complication of the two methods are the same,but the one-stage method requires less time for facial reanimation,and is costeffective because it saves time and decreases hospitalization costs.

Effect of Sodium Selenate on Hippocampal Proteome of 3×Tg-AD Mice-Exploring the Antioxidant Dogma of Selenium against Alzheimer's Disease.

Science.gov (United States)

Iqbal, Javed; Zhang, Kaoyuan; Jin, Na; Zhao, Yuxi; Liu, Qiong; Ni, Jiazuan; Shen, Liming

2018-04-19

Selenium (Se), an antioxidant trace element, is an important nutrient for maintaining brain functions and is reported to be involved in Alzheimer's disease (AD) pathologies. The present study has been designed to elucidate the protein changes in hippocampus of 3×Tg-AD mice after supplementing sodium selenate as an inorganic source of selenium. By using iTRAQ proteomics technology, 113 differentially expressed proteins (DEPs) are found in AD/WT mice with 37 upregulated and 76 downregulated proteins. Similarly, in selenate-treated 3×Tg-AD (ADSe/AD) mice, 115 DEPs are found with 98 upregulated and 17 downregulated proteins. The third group of mice (ADSe/WT) showed 75 DEPs with 46 upregulated and 29 downregulated proteins. Among these results, 42 proteins (40 downregulated and 2 upregulated) in the diseased group showed reverse expression when treated with selenate. These DEPs are analyzed with different bioinformatics tools and are found associated with various AD pathologies and pathways. Based on their functions, selenate-reversed proteins are classified as structural proteins, metabolic proteins, calcium regulating proteins, synaptic proteins, signaling proteins, stress related proteins, and transport proteins. Six altered AD associated proteins are successfully validated by Western blot analysis. This study shows that sodium selenate has a profound effect on the hippocampus of the triple transgenic AD mice. This might be established as an effective therapeutic agent after further investigation.

Rapid fabrication of self-ordered porous alumina with 10-/sub-10-nm-scale nanostructures by selenic acid anodizing

Science.gov (United States)

Nishinaga, Osamu; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O.

2013-01-01

Anodic porous alumina has been widely investigated and used as a nanostructure template in various nanoapplications. The porous structure consists of numerous hexagonal cells perpendicular to the aluminum substrate and each cell has several tens or hundreds of nanoscale pores at its center. Because the nanomorphology of anodic porous alumina is limited by the electrolyte during anodizing, the discovery of additional electrolytes would expand the applicability of porous alumina. In this study, we report a new self-ordered nanoporous alumina formed by selenic acid (H2SeO4) anodizing. By optimizing the anodizing conditions, anodic alumina possessing 10-nm-scale pores was rapidly assembled (within 1 h) during selenic acid anodizing without any special electrochemical equipment. Novel sub-10-nm-scale spacing can also be achieved by selenic acid anodizing and metal sputter deposition. Our new nanoporous alumina can be used as a nanotemplate for various nanostructures in 10-/sub-10-nm-scale manufacturing. PMID:24067318

Meta-analysis of Gaussian individual patient data: Two-stage or not two-stage?

Science.gov (United States)

Morris, Tim P; Fisher, David J; Kenward, Michael G; Carpenter, James R

2018-04-30

Quantitative evidence synthesis through meta-analysis is central to evidence-based medicine. For well-documented reasons, the meta-analysis of individual patient data is held in higher regard than aggregate data. With access to individual patient data, the analysis is not restricted to a "two-stage" approach (combining estimates and standard errors) but can estimate parameters of interest by fitting a single model to all of the data, a so-called "one-stage" analysis. There has been debate about the merits of one- and two-stage analysis. Arguments for one-stage analysis have typically noted that a wider range of models can be fitted and overall estimates may be more precise. The two-stage side has emphasised that the models that can be fitted in two stages are sufficient to answer the relevant questions, with less scope for mistakes because there are fewer modelling choices to be made in the two-stage approach. For Gaussian data, we consider the statistical arguments for flexibility and precision in small-sample settings. Regarding flexibility, several of the models that can be fitted only in one stage may not be of serious interest to most meta-analysis practitioners. Regarding precision, we consider fixed- and random-effects meta-analysis and see that, for a model making certain assumptions, the number of stages used to fit this model is irrelevant; the precision will be approximately equal. Meta-analysts should choose modelling assumptions carefully. Sometimes relevant models can only be fitted in one stage. Otherwise, meta-analysts are free to use whichever procedure is most convenient to fit the identified model. © 2018 The Authors. Statistics in Medicine Published by John Wiley & Sons Ltd.

On the prior probabilities for two-stage Bayesian estimates

International Nuclear Information System (INIS)

Kohut, P.

1992-01-01

The method of Bayesian inference is reexamined for its applicability and for the required underlying assumptions in obtaining and using prior probability estimates. Two different approaches are suggested to determine the first-stage priors in the two-stage Bayesian analysis which avoid certain assumptions required for other techniques. In the first scheme, the prior is obtained through a true frequency based distribution generated at selected intervals utilizing actual sampling of the failure rate distributions. The population variability distribution is generated as the weighed average of the frequency distributions. The second method is based on a non-parametric Bayesian approach using the Maximum Entropy Principle. Specific features such as integral properties or selected parameters of prior distributions may be obtained with minimal assumptions. It is indicated how various quantiles may also be generated with a least square technique

Selen og vitamin E til søer og pattegrise

DEFF Research Database (Denmark)

Nielsen, H. E.; Danielsen, V.; Simesen, M. G.

1977-01-01

Formålet med dette forsøg var at undersøge virkningen af foderets selen- og vitamin E indhold på søernes frugtbarhed og pattegrisenes levedygtighed og vækst. Endvidere at undersøge koncentrationen af selen (Se) og vitamin E i råmælk, somælk og blod i relation til foderet. Der forekom enkelte...... dødsfald blandt grisene, som kunne sættes i forbindelse med enten lavt Se-indhold eller lavt vitamin E indhold i foderet. Der blev desuden konstateret flere brunst- og drægtighedsproblemer hos søer, derfik foder med det lave indhold af vitamin E end hos søer i de andre grupper. En forøgelse af Se......-indholdet fra 30 til 60 µg pr. kg foder gav en fordobling af indholdet i råmælk og i somælk. En forøgelse af vitamin E indholdet i foderet fra ca. 20 mg til ca. 45 mg pr. kg foder gav 4 gange forøgelse i råmælk og somælk. Der blev konstateret tilsvarende virkninger af Se og vitamin E i foderet på indholdet i...

Combination cancer treatment through photothermally controlled release of selenous acid from gold nanocages.

Science.gov (United States)

Cheng, Haoyan; Huo, Da; Zhu, Chunlei; Shen, Song; Wang, Wenxia; Li, Haoxuan; Zhu, Zhihong; Xia, Younan

2018-04-03

Selenite, one of the inorganic forms of selenium, is emerging as an attractive chemotherapeutic agent owing to its selectivity in eradicating cancer cells. Here we demonstrate a new formulation of nanomedicine based on selenous acid, which is mixed with lauric acid (a phase-change material with a melting point around 43 °C) and then loaded into the cavities of Au nanocages. The Au nanocages can serve as a carrier during cell endocytosis and then as a photothermal agent to melt the lauric acid upon the irradiation with a near-infrared laser, triggering the swift release of selenous acid. The photothermal and chemo therapies can also work synergistically, leading to enhanced destruction of cancer cells relative to normal cells. Our systematic study suggests that the impaired mitochondrial function arising from the ROS generated through combination treatment is responsible for the cell death. This study offers an appealing candidate that holds great promise for synergistic cancer treatment. Published by Elsevier Ltd.

Comparison of two techniques used for the recovery of third-stage strongylid nematode larvae from herbage.

Science.gov (United States)

Krecek, R C; Maingi, N

2004-07-14

A laboratory trial to determine the efficacy of two methods in recovering known numbers of third-stage (L3) strongylid nematode larvae from herbage was carried out. Herbage samples consisting almost entirely of star grass (Cynodon aethiopicus) that had no L3 nematode parasitic larvae were collected at Onderstepoort, South Africa. Two hundred grams samples were placed in fibreglass fly gauze bags and seeded with third-stage strongylid nematode larvae at 11 different levels of herbage infectivity ranging from 50 to 8000 L3/kg. Eight replicates were prepared for each of the 11 levels of herbage infectivity. Four of these were processed using a modified automatic Speed Queen heavy-duty washing machine at a regular normal cycle, followed by isolation of larvae through centrifugation-flotation in saturated sugar solution. Larvae in the other four samples were recovered after soaking the herbage in water overnight and the larvae isolated with the Baermann technique of the washing. There was a strong correlation between the number of larvae recovered using both methods and the number of larvae in the seeded samples, indicating that the two methods give a good indication of changes in the numbers of larvae on pasture if applied in epidemiological studies. The washing machine method recovered higher numbers of larvae than the soaking and Baermann method at all levels of pasture seeding, probably because the machine washed the samples more thoroughly and a sugar centrifugation-flotation step was used. Larval suspensions obtained using the washing machine method were therefore cleaner and thus easier to examine under the microscope. In contrast, the soaking and Baermann method may be more suitable in field-work, especially in places where resources and equipment are scarce, as it is less costly in equipment and less labour intensive. Neither method recovered all the larvae from the seeded samples. The recovery rates for the washing machine method ranged from 18 to 41% while

Two-step technique for posterior optic buttonholing of intraocular lens.

Science.gov (United States)

Agarwal, Tushar; Jhanji, Vishal; Singh, Digvijay; Khokhar, Sudarshan

2014-04-01

This study aims to describe a two-step surgical technique for placement of a posterior chamber intraocular lens (IOL) in cases with crystalline lens subluxation resulting from non-progressive zonular dialysis. The first stage entails a phacoemulsification with creation of a 4-mm posterior capsular opening using an automated vitrector. The second stage performed 6 weeks later includes an anterior vitrectomy and injection of a foldable three-piece IOL in the sulcus. The haptics of IOL are positioned in the sulcus while the optic is pushed behind the posterior capsular opening therefore "buttonholing" the IOL. Seven eyes of seven patients with posttraumatic zonular dialysis were operated using this technique. Follow-up of all cases revealed a well-centered IOL with good postoperative visual acuity (20/20 to 20/80). Our two-stage surgical technique precludes the insertion of capsular tension ring in cases with non-progressive zonular dialysis. The technique is recommended in the presence of less than or equal to 6 clock hours of zonular dialysis with preexisting posterior capsular tear or herniation of vitreous in the anterior chamber.

Preparation of SnSe thin films by encapsulated selenization

International Nuclear Information System (INIS)

Sabar D. Hutagalung; Samsudi Sakrani; Yussof Wahab

1994-01-01

Tin selenide thin films were prepared by encapsulated selenization. A stacked layer of evaporated Sn and Se films were annealed in a carbon block at temperatures 100 - 500 degree Celsius for 3 hours. X-ray analysis and SEM (Scanning electron) micrograph results showed that SnSe was initially formed at 150 degree Celsius with crystal size 30.0 nm and reached optimum formation at 200 daximum of 57.4 % yield of 5-decene. Other factors such as reaction temperatures, types of solvent and wt% of rhenium loadings influence the activity of the catalytic system

Sorption mechanisms of selenium species (selenite and selenate) on copper-based minerals

International Nuclear Information System (INIS)

Devoy, J.

2001-09-01

The sorption of radionuclides on the surface of minerals represents a process capable to delay the migration of the elements from a spent fuel deep repository towards the biosphere. In the framework of a deep underground repository, an engineered clay barrier has a high trapping capacity for cationic radio-elements, in particular because of the negative charge of clay surfaces. However, anionic radioelements like selenium species, would be only weakly retained by chemical processes. In order to optimize the trapping capacity of a clay barrier with respect to anionic species, prospective studies are carried out in order to find and evaluate some minerals with specific chemical trapping functions. Among radionuclides, the case of selenium has to be considered because its isotope 79 Se is present in radioactive wastes and has a half life time of 6.5 10 4 years. It is also judicious to find a mineral capable of trapping simultaneously several anionic radio-elements. Copper oxides and sulfides (Cu 2 O, CuO, Cu 2 S, CuS, CuFeS 2 and Cu 5 FeS 4 ) are good adsorbents with respect to selenium species (selenite and selenate). These minerals, with their selenium retention properties, could be used also for the decontamination of soils and waters or to process industrial effluents. The sorption mechanisms have been studied in details for copper oxides (Cu 2 O and CuO) with respect to selenite and selenate. Chalcomenite precipitates in acid pH conditions when selenite is added to a Cu 2 O and CuO suspension. Selenate, in contact with cuprite (Cu 2 O) leads also to a selenium-based precipitate in acid pH environment. For higher pH values, selenite and selenate are adsorbed on copper oxides (Cu 2 O and CuO) and lead to internal and external sphere complexes, respectively. In the case of a selenite/cuprite mixture in basic pH environment and at the equilibrium, a chemical reaction occurs between the oxidation product of cuprite, Cu(OH) 2 and HSeO 3 . A preliminary study of

Managing uncertainty - a qualitative study of surgeons' decision-making for one-stage and two-stage revision surgery for prosthetic hip joint infection.

Science.gov (United States)

Moore, Andrew J; Blom, Ashley W; Whitehouse, Michael R; Gooberman-Hill, Rachael

2017-04-12

Approximately 88,000 primary hip replacements are performed in England and Wales each year. Around 1% go on to develop deep prosthetic joint infection. Between one-stage and two-stage revision arthroplasty best treatment options remain unclear. Our aims were to characterise consultant orthopaedic surgeons' decisions about performing either one-stage or two-stage revision surgery for patients with deep prosthetic infection (PJI) after hip arthroplasty, and to identify whether a randomised trial comparing one-stage with two-stage revision would be feasible. Semi-structured interviews were conducted with 12 consultant surgeons who perform revision surgery for PJI after hip arthroplasty at 5 high-volume National Health Service (NHS) orthopaedic departments in England and Wales. Surgeons were interviewed before the development of a multicentre randomised controlled trial. Data were analysed using a thematic approach. There is no single standardised surgical intervention for the treatment of PJI. Surgeons balance multiple factors when choosing a surgical strategy which include multiple patient-related factors, their own knowledge and expertise, available infrastructure and the infecting organism. Surgeons questioned whether it was appropriate that the two-stage revision remained the best treatment, and some surgeons' willingness to consider more one-stage revisions had increased over recent years and were influenced by growing evidence showing equivalence between surgical techniques, and local observations of successful one-stage revisions. Custom-made articulating spacers was a practice that enabled uncertainty to be managed in the absence of definitive evidence about the superiority of one surgical technique over the other. Surgeons highlighted the need for research evidence to inform practice and thought that a randomised trial to compare treatments was needed. Most surgeons thought that patients who they treated would be eligible for trial participation in instances

Preparation, solubility, infrared spectra and radiolysis of tetramethylammonium hydrogenselenate monohydrate and lithium tetramethylammonium selenate tetrahydrate

Czech Academy of Sciences Publication Activity Database

Havlíček, D.; Turek, L.; Plocek, Jiří; Mička, Z.

2006-01-01

Roč. 71, č. 3 (2006), s. 411-422 ISSN 0010-0765 Institutional research plan: CEZ:AV0Z40320502 Keywords : tetramethylammonium salts * hydrogenselenates * selenates Subject RIV: CA - Inorganic Chemistry Impact factor: 0.881, year: 2006

Preparation and Characterization of Cu(In,GaSe2 Thin Films by Selenization of Cu0.8Ga0.2 and In2Se3 Precursor Films

Directory of Open Access Journals (Sweden)

Jiang Liu

2012-01-01

Full Text Available Se-containing precursor films with two different compositions were prepared by magnetron sputtering from and targets, and then were selenized using Se vapor. The effects of precursor composition and selenization temperature on the film properties were investigated. The results show that Se phase plays a critical role in film growth and electrical properties of CIGS films. The Cu-rich films exhibit different surface morphology and better crystallinity, as compared to the Cu-poor films. All the CIGS films exhibit p-type conductivity. The resistivity of the Cu-rich films is about three orders of magnitude lower than that of the Cu-poor films, which is attributed to the presence of p-type highly conductive Se phase.

Optics of two-stage photovoltaic concentrators with dielectric second stages

Science.gov (United States)

Ning, Xiaohui; O'Gallagher, Joseph; Winston, Roland

1987-04-01

Two-stage photovoltaic concentrators with Fresnel lenses as primaries and dielectric totally internally reflecting nonimaging concentrators as secondaries are discussed. The general design principles of such two-stage systems are given. Their optical properties are studied and analyzed in detail using computer ray trace procedures. It is found that the two-stage concentrator offers not only a higher concentration or increased acceptance angle, but also a more uniform flux distribution on the photovoltaic cell than the point focusing Fresnel lens alone. Experimental measurements with a two-stage prototype module are presented and compared to the analytical predictions.

Optics of two-stage photovoltaic concentrators with dielectric second stages.

Science.gov (United States)

Ning, X; O'Gallagher, J; Winston, R

1987-04-01

Two-stage photovoltaic concentrators with Fresnel lenses as primaries and dielectric totally internally reflecting nonimaging concentrators as secondaries are discussed. The general design principles of such two-stage systems are given. Their optical properties are studied and analyzed in detail using computer ray trace procedures. It is found that the two-stage concentrator offers not only a higher concentration or increased acceptance angle, but also a more uniform flux distribution on the photovoltaic cell than the point focusing Fresnel lens alone. Experimental measurements with a two-stage prototype module are presented and compared to the analytical predictions.

Single-stage-to-orbit versus two-stage-two-orbit: A cost perspective

Science.gov (United States)

Hamaker, Joseph W.

1996-03-01

This paper considers the possible life-cycle costs of single-stage-to-orbit (SSTO) and two-stage-to-orbit (TSTO) reusable launch vehicles (RLV's). The analysis parametrically addresses the issue such that the preferred economic choice comes down to the relative complexity of the TSTO compared to the SSTO. The analysis defines the boundary complexity conditions at which the two configurations have equal life-cycle costs, and finally, makes a case for the economic preference of SSTO over TSTO.

Radiologic techniques in staging malignant lymphoma

International Nuclear Information System (INIS)

Strijk, S.P.

1987-01-01

The main subject of this thesis is the evaluation of radiologic techniques in staging patients with newly diagnosed and untreated malignant lymphoma, or restaging patients with recurrent disease after a period of complete remission. Lymphography and, more recently, CT are available to examine the infradiaphragmatic nodes. CT also offers the possibility to examine other organ systems in the abdomen, and to visualize more lymph-node regions than lymphography. In ch. 2 and 4 the diagnostic performance of CT and lymphography in HD and NHL respectively are discussed. Literature data are summarized, and own results are given. The main goal is to determine whether the two methods are overlapping, competitive or complementary, and to answer the question what would be required for optimal staging. Staging laparotomy showed the unreliability of non-invasive examination methods for determining the presence or absence of lymphoma in the spleen. In ch. 3 and 5 the results of CT-based estimations of size of the spleen in relation to its histologic state, in patients with HD and NHL respectively are presented. The chest can be examined for lymphoma by conventional radiography, conventional tomography or computed tomography (CT). In ch. 6 the literature is reviewed, and the results with our patients are presented. The diagnostic performance of each examination is evaluated, and the results are analysed to define the most desirable approach in the examination of the chest for staging purposes. In ch. 7 the uncommon radiologic observation of calcification in lymph nodes, afflicted with HD and NHL is described. The literature is reviewed, and the clinical significance is indicated. 180 refs.; 22 figs.; 24 tabs

Community ecology of the metazoan parasites of Atlantic Moonfish, Selene setapinnis (Osteichthyes: Carangidae from the coastal zone of the state of Rio de Janeiro, Brazil

Directory of Open Access Journals (Sweden)

A. S. Cordeiro

Full Text Available Eighty-nine specimens of Selene setapinnis (Mitchill, 1815 collected from the coastal zone of the State of Rio de Janeiro (21-23ºS, 41-45ºW and 23º05'S, 44º30'W, Brazil, from August 2001 to May 2002, were necropsied to study their metazoan parasites. Eighty-one (91% specimens of S. setapinnis were parasitized by one or more metazoan species. Twenty-one species of parasites were collected: 8 digeneans, 3 monogeneans, 2 cestodes, 5 nematodes, and 3 copepods. The endoparasites (digeneans, cestodes, and nematodes were 74.1% of total number of parasite specimens collected. The monogenean Pseudomazocraes selene (Hargis, 1957 was the most dominant species with the highest prevalence in the parasite community of S. setapinnis. The metazoan parasites of this host species showed the typical aggregated pattern of distribution. Only one parasite species (Acanthocolpoides pauloi Travassos, Freitas & Buhrnheim, 1955 showed positive correlation between the host total length and parasite abundance in S. setapinnis. Caligus robustus Bassett-Smith, 1898, P. selene, and Terranova sp. demonstrated positive correlation between the host total length and prevalence. Larvae of Terranova sp. showed influence of the host sex on its prevalence. A pair of ectoparasite species, P. selene-C. robustus, exhibited positive covariation between their abundances. Two pairs of endoparasite species, L. microstomum-P. merus and A. pauloi-P. merus showed significant covariation among their abundances; and the pair Terranova sp.-Raphidascaris sp. had positive co-ocorrence and covariation in the infracommunities of S. setapinnis. Like the parasite communities of the other carangid fishes from Rio de Janeiro, the parasite community of S. setapinnis is apparently only a slightly ordered species complex, characterized by dominance of endoparasite species.

Controlled formation of MoSe{sub 2} by MoN{sub x} thin film as a diffusion barrier against Se during selenization annealing for CIGS solar cell

Energy Technology Data Exchange (ETDEWEB)

Jeon, Chan-Wook [School of Chemical Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Cheon, Taehoon [School of Materials Science and Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Center for Core Research Facilities, DaeguGyeongbuk Institute of Science & Technology, Daegu (Korea, Republic of); Kim, Hangil [School of Materials Science and Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Kwon, Min-Su [School of Chemical Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of); Kim, Soo-Hyun [School of Materials Science and Engineering, Yeungnam University, Gyeongsangbuk-do 712-749 (Korea, Republic of)

2015-09-25

Highlights: • Mo/MoN{sub x}/Mo multilayer was investigated as a back contact for CIGS solar cell. • The MoN{sub x} protected the underlying Mo layer during high temperature selenization. • The formation of MoSe{sub 2} layer was precisely controlled. • The diffusion barrier performance of MoN{sub x} against Se was evaluated using TEM analysis. - Abstract: This study investigated the interfacial reactions and electrical properties of a Mo single layer and Mo/MoN{sub x}/Mo multilayer during high temperature selenization annealing. The Mo single layer was converted easily to MoSe{sub 2}, which was 7 times thicker than the Mo layer consumed ∼900 nm, by selenization at 460 °C for 10 min and the sheet resistance increased 8 fold compared to that of the as-deposited Mo film. On the other hand, in the Mo/MoN{sub x}/Mo structure, transmission electron microscopy (TEM) showed that the MoSe{sub 2} transformation was localized only in the top Mo layer and the bottom Mo layer was completely unaffected, even after selenization at 560 °C. The sheet resistance of the multilayer was relatively unchanged by selenization. This suggests that the MoN{sub x} layer performed well as a diffusion barrier against Se and the thickness of MoSe{sub 2} can be controlled precisely by adjusting the top Mo layer thickness. Furthermore, TEM and energy dispersive spectroscopy analysis showed that the selenized multilayer consisted of MoSe{sub 2}/Mo/MoN{sub x}/Mo, in which the top Mo layer of 60 nm was not fully converted to MoSe{sub 2} and 20 nm was left unreacted. The residual Mo interlayer located at the interface of MoSe{sub 2} and MoN{sub x} is believed to be beneficial for the ohmic contact of the selenized multilayer.

Formation of CuInSe{sub 2} films from metal sulfide and selenide precursor nanocrystals by gas-phase selenization, an in-situ XRD study

Energy Technology Data Exchange (ETDEWEB)

Capon, B., E-mail: boris.capon@ugent.be [Department of Solid State Sciences, Ghent University, Krijgslaan 281-S1, B-9000 Ghent (Belgium); Dierick, R. [Physics and Chemistry of Nanostructures, Ghent University, Krijgslaan 281-S3, B-9000 Ghent (Belgium); Hens, Z. [Physics and Chemistry of Nanostructures, Ghent University, Krijgslaan 281-S3, B-9000 Ghent (Belgium); Center for Nano and Biophotonics, Ghent University, Ghent (Belgium); Detavernier, C. [Department of Solid State Sciences, Ghent University, Krijgslaan 281-S1, B-9000 Ghent (Belgium)

2016-08-01

In this work phase pure CuInSe{sub 2} thin flms were obtained by selenization of ternary CuInSe{sub 2} and CuInS{sub 2} nanocrystals and mixtures of binary nanocrystals such as CuS, In{sub 2}S{sub 3}, Cu{sub 2}Se and In{sub 2}Se{sub 3}. The temperature of the selenium source was kept at 400 °C during selenization. Monitoring the process using in-situ x-ray diffraction, the effect of selenization on the phase formation and grain growth in the precursor film was investigated. Whereas CuInSe{sub 2} and CuInS{sub 2} nanocrystals exhibit little grain growth, we found that mixtures of binary nanocrystals can show significant sintering depending on the reaction conditions. For the mixture of CuS and In{sub 2}S{sub 3} nanocrystals, the crystallinity and the morphology of the obtained fims strongly depends on the Cu/In ratio, with a Cu excess strongly promoting grain growth. With mixtures of Cu{sub 2}Se and In{sub 2}Se{sub 3} nanocrystals the selenium partial pressure plays a crucial role. Selenium evaporation from the mixed compounds results in CuInSe{sub 2} films composed of relatively small crystallites. Higher selenium partial pressures however resulted in improved sintering. Incomplete propagation of the selenization reaction through the layer was observed though, only leading to a well sintered CuInSe{sub 2} top layer above a fine grained bottom layer. - Highlights: • Different types of colloidal nanocrystals were used as precursors to obtain CuInSe{sub 2} films by gas-phase selenization. • In-situ XRD was used to study the effect of selenization on the phase formation and grain growth in the precursor films. • For a mixture of binary metal sulfides the crystallinity and the morphology strongly depend on the Cu/In ratio. • Higher selenium partial pressures result in improved sintering for a mixture of binary metal selenides.

Rover exploration on the lunar surface; a science proposal for SELENE-B mission

Science.gov (United States)

Sasaki, S.; Kubota, T.; Akiyama, H.; Hirata, N.; Kunii, Y.; Matsumoto, K.; Okada, T.; Otake, M.; Saiki, K.; Sugihara, T.

LUNARSURFACE:ASCIENCES. Sasaki (1), T. Kubota (2) , H. Akiyama (1) , N. Hirata (3), Y. Kunii (4), K. Matsumoto (5), T. Okada (2), M. Otake (3), K. Saiki (6), T. Sugihara (3) (1) Department of Earth and Planetary Science, Univ. Tokyo, (2) Institute of Space and Astronautical Sciences, (3) National Space Development Agency of Japan, (4) Department of Electrical and Electronic Engineering, Chuo Univ., (5) National Aerospace Laboratory of Japan, (6) Research Institute of Materials and Resources, Akita Univ. sho@eps.s.u -tokyo.ac.jp/Fax:+81-3-5841-4569 A new lunar landing mission (SELENE-B) is now in consideration in Japan. Scientific investigation plans using a rover are proposed. To clarify the origin and evolution of the moon, the early crustal formation and later mare volcanic processes are still unveiled. We proposed two geological investigation plans: exploration of a crater central peak to discover subsurface materials and exploration of dome-cone structures on young mare region. We propose multi-band macro/micro camera using AOTF, X-ray spectrometer/diffractometer and gamma ray spectrometer. Since observation of rock fragments in brecciaed rocks is necessary, the rover should have cutting or scraping mechanism of rocks. In our current scenario, landing should be performed about 500m from the main target (foot of a crater central peak or a cone/dome). After the spectral survey by multi-band camera on the lander, the rover should be deployed for geological investigation. The rover should make a short (a few tens meter) round trip at first, then it should perform traverse observation toward the main target. Some technological investigations on SELENE-B project will be also presented.

Comparisons of single-stage and two-stage approaches to genomic selection.

Science.gov (United States)

Schulz-Streeck, Torben; Ogutu, Joseph O; Piepho, Hans-Peter

2013-01-01

Genomic selection (GS) is a method for predicting breeding values of plants or animals using many molecular markers that is commonly implemented in two stages. In plant breeding the first stage usually involves computation of adjusted means for genotypes which are then used to predict genomic breeding values in the second stage. We compared two classical stage-wise approaches, which either ignore or approximate correlations among the means by a diagonal matrix, and a new method, to a single-stage analysis for GS using ridge regression best linear unbiased prediction (RR-BLUP). The new stage-wise method rotates (orthogonalizes) the adjusted means from the first stage before submitting them to the second stage. This makes the errors approximately independently and identically normally distributed, which is a prerequisite for many procedures that are potentially useful for GS such as machine learning methods (e.g. boosting) and regularized regression methods (e.g. lasso). This is illustrated in this paper using componentwise boosting. The componentwise boosting method minimizes squared error loss using least squares and iteratively and automatically selects markers that are most predictive of genomic breeding values. Results are compared with those of RR-BLUP using fivefold cross-validation. The new stage-wise approach with rotated means was slightly more similar to the single-stage analysis than the classical two-stage approaches based on non-rotated means for two unbalanced datasets. This suggests that rotation is a worthwhile pre-processing step in GS for the two-stage approaches for unbalanced datasets. Moreover, the predictive accuracy of stage-wise RR-BLUP was higher (5.0-6.1%) than that of componentwise boosting.

Hypospadias repair: Byar's two stage operation revisited.

Science.gov (United States)

Arshad, A R

2005-06-01

Hypospadias is a congenital deformity characterised by an abnormally located urethral opening, that could occur anywhere proximal to its normal location on the ventral surface of glans penis to the perineum. Many operations had been described for the management of this deformity. One hundred and fifteen patients with hypospadias were treated at the Department of Plastic Surgery, Hospital Kuala Lumpur, Malaysia between September 1987 and December 2002, of which 100 had Byar's procedure performed on them. The age of the patients ranged from neonates to 26 years old. Sixty-seven patients had penoscrotal (58%), 20 had proximal penile (18%), 13 had distal penile (11%) and 15 had subcoronal hypospadias (13%). Operations performed were Byar's two-staged (100), Bracka's two-staged (11), flip-flap (2) and MAGPI operation (2). The most common complication encountered following hypospadias surgery was urethral fistula at a rate of 18%. There is a higher incidence of proximal hypospadias in the Malaysian community. Byar's procedure is a very versatile technique and can be used for all types of hypospadias. Fistula rate is 18% in this series.

Simultaneous versus sequential pharmacokinetic-pharmacodynamic population analysis using an iterative two-stage Bayesian technique

NARCIS (Netherlands)

Proost, Johannes H.; Schiere, Sjouke; Eleveld, Douglas J.; Wierda, J. Mark K. H.

A method for simultaneous pharmacokinetic-pharmacodynamic (PK-PD) population analysis using an Iterative Two-Stage Bayesian (ITSB) algorithm was developed. The method was evaluated using clinical data and Monte Carlo simulations. Data from a clinical study with rocuronium in nine anesthetized

Bioavailability of selenium from fish, yeast and selenate: A comparative study in humans using stable isotopes

NARCIS (Netherlands)

Fox, T.E.; Heuvel, E.G.H.M. van den; Atherton, C.A.; Dainty, J.R.; Lewis, D.J.; Langford, N.J.; Crews, H.M.; Luten, J.B.; Lorentzen, M.; Sieling, F.W.; Aken-Schneyder, P. van; Hoek, M.; Kotterman, M.J.J.; Dael, P. van; Firweather-Tail, S.J.

2004-01-01

Objective: To measure the bioavailability of selenium from cooked and raw fish in humans by estimating and comparing apparent absorption and retention of selenium in biosynthetically labelled fish with labelled selenate and biosynthetically labelled selenium in brewers yeast. Design: The

Bioavailibility of selenium from fish, yeast and selenate: a comparative study in humans using stable isotopes

NARCIS (Netherlands)

Fox, T.E.; Heuvel, van den E.G.H.M.; Atherton, C.A.; Luten, J.B.; Hoek-van Nieuwenhuizen, van M.; Kotterman, M.J.J.

2004-01-01

Objective: To measure the bioavailability of selenium from cooked and raw fish in humans by estimating and comparing apparent absorption and retention of selenium in biosynthetically labelled fish with labelled selenate and biosynthetically labelled selenium in brewers yeast. Design: The

The Effect of E-Selen Antioxidant on the Fatty Acids Content of the Homogenate of Unirradiated and Irradiated Pupae of Ceratitis Capitata

International Nuclear Information System (INIS)

Zaghloul, Y.S.; Abbassy, S.A.; Elakhdar, E.A.H.; Elakhdar, E.A.H.

2011-01-01

As antioxidant E-selen was added to the larval artificial diets of the Mediterranean fruit fly, Ceratitis capitata. The produced full grown pupae were exposed to gamma rays at dose rate of 90 Gy. The fatty acid contents of the normal and irradiated insects were analyzed to test to what extent, the uptake of the antioxidant will ameliorate the physiological damage induced to the medfly pupae, as a result of their exposure to irradiation. The results obtained by using Gas-liquid chromatography of fatty acid methyl esters, showed the palmitic and oleic acids to be the most predominant fatty acids in all pupal homogenates in both normal and irradiated pupae, either by the uptake of doses of the E-selen or without. The uptake of E-Selen with a dose of 0.3 mg led to a complete absence of the lauric and myristic acids in the homogenates of the unirradiated pupae of the medfly. This absence of lauric and myristic acids was accompanied by a decrease in the concentrations of the palmitic and linoleic acids reaching 25.17% and 32.98%, respectively as compared to pupae without the uptake of antioxidant. The concentrations of both the stearic and oleic acids showed an obvious increment reaching 199.22% and 58.94%, respectively, relative to those reared on the defined media and no added E.Selen. Exposure of the pupae to a dose of 90 Gy, resulted in an increment in the concentrations of the saturated lauric and myristic acid reaching 96.77% and 34.07%, respectively, relative to the untreated ones. While, at the same dose level, there were decrements in the concentrations of the palmitic, stearic, oleic and linoleic acids with percentages reaching 6.4, 9.22, 3.65 and 1.15%, respectively as compared to unirradiated controls. Irradiation of the pupae with sterilizing dose (90 Gy) after up taking the E-Selen in their larval diets, led to the increase of the concentrations of lauric, oleic and linoleic acids by ratios of 16.82, 8.84 and 29.26%, respectively as compared to their

Design considerations for single-stage and two-stage pneumatic pellet injectors

International Nuclear Information System (INIS)

Gouge, M.J.; Combs, S.K.; Fisher, P.W.; Milora, S.L.

1988-09-01

Performance of single-stage pneumatic pellet injectors is compared with several models for one-dimensional, compressible fluid flow. Agreement is quite good for models that reflect actual breech chamber geometry and incorporate nonideal effects such as gas friction. Several methods of improving the performance of single-stage pneumatic pellet injectors in the near term are outlined. The design and performance of two-stage pneumatic pellet injectors are discussed, and initial data from the two-stage pneumatic pellet injector test facility at Oak Ridge National Laboratory are presented. Finally, a concept for a repeating two-stage pneumatic pellet injector is described. 27 refs., 8 figs., 3 tabs

Uptake of selenate on hydrated and degraded cement: batch and dynamic experiments

International Nuclear Information System (INIS)

Rojo, I.; Rovira, I.; Marti, V.; Pablo, J. de; Duro, L.; Gaona, X.; Colas, E.; Grive, M.

2009-01-01

The evaluation of selenate sorption and retardation in batch and dynamic experiments on hydrated and degraded cement has been studied. Desorption studies have also been carried in order to assess the reversibility of the sorption process. Sorption data onto degraded cement have been treated assuming the formation of surface complexes, whereas sorption kinetics has been fitted by using a pseudo-first order kinetic equation. Dynamic flow experiments have also been modelled. (authors)

Two-Stage Series-Resonant Inverter

Science.gov (United States)

Stuart, Thomas A.

1994-01-01

Two-stage inverter includes variable-frequency, voltage-regulating first stage and fixed-frequency second stage. Lightweight circuit provides regulated power and is invulnerable to output short circuits. Does not require large capacitor across ac bus, like parallel resonant designs. Particularly suitable for use in ac-power-distribution system of aircraft.

Two-stage anaerobic digestion of cheese whey

Energy Technology Data Exchange (ETDEWEB)

Lo, K V; Liao, P H

1986-01-01

A two-stage digestion of cheese whey was studied using two anaerobic rotating biological contact reactors. The second-stage reactor receiving partially treated effluent from the first-stage reactor could be operated at a hydraulic retention time of one day. The results indicated that two-stage digestion is a feasible alternative for treating whey. 6 references.

Comparison of relaxation with counterpressure massage techniques for reduce pain first stage of labor

Science.gov (United States)

Lisa, U. F.; Jalina, M.; Marniati

2017-09-01

Based on interviews of so me mother who entered the first stage of labor lack of care from health workers to the effort to reducing the acuteof labor. Health care workers appertain hospital in effective in implement maternity nursing interventions in reducing acute the first stage of labor. The reducing acute have two method are pharmacological and non-pharmacological. In this case, has several techniques there are: relaxation and counterpressure massage techniques that capable to reducing acute first stage of labor. The of non-pharmacological is one of authority which must be implemented by midwives especially breathing relaxation techniquesand massage. The research is Quasi Exsperimen with pretes-posttest design. The statistic test has T test paired and unpairedt test. To indicatea reducing the level of acute before and after given relaxation technique result p-value pain. Therefore, the health of workers, especially for a study to apply relaxation and massage to provide of mother care, mainly to the primigravida who in experienced in process of labor.

On the robustness of two-stage estimators

KAUST Repository

Zhelonkin, Mikhail

2012-04-01

The aim of this note is to provide a general framework for the analysis of the robustness properties of a broad class of two-stage models. We derive the influence function, the change-of-variance function, and the asymptotic variance of a general two-stage M-estimator, and provide their interpretations. We illustrate our results in the case of the two-stage maximum likelihood estimator and the two-stage least squares estimator. © 2011.

Observation of Possible Lava Tube Skylights by SELENE cameras

Science.gov (United States)

Haruyama, Junichi; Hiesinger, Harald; van der Bogert, Carolyn

We have discovered three deep hole-structures on the Moon in the Terrain Camera and Multi-band Imager on the SELENE. These holes are large depth to diameter ratios: Marius Hills Hole (MHH) is 65 m in diameter and 88-90 m in depth, Mare Tranquillitatis Hole (MTH) is 120 x 110 m in diameter and 180 m in depth, and Mare Ingenii Hole (MIH) is 140 x 110 m in diameter and deeper than 90 m. No volcanic material from the holes nor dike-relating pit craters is seen around the holes. They are possible lava tube skylights. These holes and possibly connected tubes have a lot of scientific interests and high potentialities as lunar bases.

Influence of one- or two-stage methods for polymerizing complete dentures on adaptation and teeth movements

Directory of Open Access Journals (Sweden)

Moises NOGUEIRA

Full Text Available Abstract Introduction The quality of complete dentures might be influenced by the method of confection. Objective To evaluate the influence of two different methods of processing muco-supported complete dentures on their adaptation and teeth movements. Material and method Denture confection was assigned in two groups (n=10 for upper and lower arches according to polymerization method: 1 conventional one-stage - a wax trial base was made, teeth were arranged and polymerized; 2 two-stage method - the base was waxed and first polymerized. With the denture base polymerized, the teeth were arranged and then, performed the final polymerization. Teeth movements were evaluated in the distances between incisive (I-I, pre-molars (P-P, molars (M-M, left incisor to left molar (LI-LM and right incisor to right molar (RI-RM. For the adaptation analysis, dentures were cut in three different positions: (A distal face of canines, (B mesial face of the first molars, and (C distal face of second molars. Result Denture bases have shown a significant better adaptation when polymerized in the one-stage procedure for both the upper (p=0.000 and the lower (p=0.000 arches, with region A presenting significant better adaptation than region C. In the upper arch, significant reduction in the distance between I-I was observed in the one-stage technique, while the two-stage technique promoted significant reduction in the RI-RM distance. In the lower arch, one-stage technique promoted significant reduction in the distance for RI-RM and two-stage promoted significant reduction in the LI-LM distance. Conclusion Conventional one-stage method presented the better results for denture adaptation. Both fabrication methods presented some alteration in teeth movements.

Sensitivity Analysis in Two-Stage DEA

Directory of Open Access Journals (Sweden)

Athena Forghani

2015-07-01

Full Text Available Data envelopment analysis (DEA is a method for measuring the efficiency of peer decision making units (DMUs which uses a set of inputs to produce a set of outputs. In some cases, DMUs have a two-stage structure, in which the first stage utilizes inputs to produce outputs used as the inputs of the second stage to produce final outputs. One important issue in two-stage DEA is the sensitivity of the results of an analysis to perturbations in the data. The current paper looks into combined model for two-stage DEA and applies the sensitivity analysis to DMUs on the entire frontier. In fact, necessary and sufficient conditions for preserving a DMU's efficiency classiffication are developed when various data changes are applied to all DMUs.

Sensitivity Analysis in Two-Stage DEA

Directory of Open Access Journals (Sweden)

Athena Forghani

2015-12-01

Full Text Available Data envelopment analysis (DEA is a method for measuring the efficiency of peer decision making units (DMUs which uses a set of inputs to produce a set of outputs. In some cases, DMUs have a two-stage structure, in which the first stage utilizes inputs to produce outputs used as the inputs of the second stage to produce final outputs. One important issue in two-stage DEA is the sensitivity of the results of an analysis to perturbations in the data. The current paper looks into combined model for two-stage DEA and applies the sensitivity analysis to DMUs on the entire frontier. In fact, necessary and sufficient conditions for preserving a DMU's efficiency classiffication are developed when various data changes are applied to all DMUs.

Two stage-type railgun accelerator

International Nuclear Information System (INIS)

Ogino, Mutsuo; Azuma, Kingo.

1995-01-01

The present invention provides a two stage-type railgun accelerator capable of spiking a flying body (ice pellet) formed by solidifying a gaseous hydrogen isotope as a fuel to a thermonuclear reactor at a higher speed into a central portion of plasmas. Namely, the two stage-type railgun accelerator accelerates the flying body spiked from a initial stage accelerator to a portion between rails by Lorentz force generated when electric current is supplied to the two rails by way of a plasma armature. In this case, two sets of solenoids are disposed for compressing the plasma armature in the longitudinal direction of the rails. The first and the second sets of solenoid coils are previously supplied with electric current. After passing of the flying body, the armature formed into plasmas by a gas laser disposed at the back of the flying body is compressed in the longitudinal direction of the rails by a magnetic force of the first and the second sets of solenoid coils to increase the plasma density. A current density is also increased simultaneously. Then, the first solenoid coil current is turned OFF to accelerate the flying body in two stages by the compressed plasma armature. (I.S.)

Study of the Cupriavidus metallidurans CH34 resistance of selenite and selenate oxy-anions: accumulation, localisation and transformation of selenium; Etude de la resistance de Cupriavidus metallidurans CH34 aux oxyanions selenite et seleniate: accumulation, localisation et transformation du selenium

Energy Technology Data Exchange (ETDEWEB)

Avoscan, L

2007-06-15

Selenium is an essential trace element for the living organisms but it is very toxic at high concentration. Selenite and selenate oxides, soluble forms, highly toxic and bio-assimilable, are the most prevalent forms in the environment. Some soil micro-organisms play a dominant role and contribute to the natural cycle of selenium. Our study model, Cupriavidus (formerly Ralstonia) metallidurans CH34, a telluric bacterium characteristic of metal-contaminated biotopes, is known to resist selenite by reducing it into elemental selenium, an insoluble and less toxic form of selenium. In order to better understand the mechanisms of selenium reduction in the bacteria, three methods of speciation were combined (XAS (XANES and EXAFS), HPLC-ICP-MS and SDS-PAGEPIXE). They were completed by the direct quantification of selenium accumulated in the bacteria. Speciation analyses highlighted the existence of two mechanisms of reduction of selenium oxides in C. metallidurans CH34. Assimilation transforms selenite and selenate into organic selenium, identified as seleno-methionine and leads to its non-specific incorporation into bacterial proteins (presence of selenious proteins). Detoxication precipitates selenite in nano-particles of elemental selenium. This way of detoxication is not set up after an exposure to selenate although it is nevertheless possible to detect elemental selenium but in very small amount compared to the exposure of selenite. Seleno-diglutathion is detected in bacteria stressed by an exposure to selenate in medium limited in sulphate. Bacteria exposed to selenite accumulate 25 times more selenium than when they are exposed to selenate. The study of mutants resistant to selenite, which do not express the membrane protein DedA, showed that the accumulation of selenium after exposure to selenite is decreased compared with the wild strain meaning probable link between the transport of selenite and the DedA protein. Finally, selenate would use the sulphate permease

One-stage lengthening using a locked nailing technique for distal femoral shaft nonunions associated with shortening.

Science.gov (United States)

Wu, Chi-Chuan; Lee, Zhon-Liau

2004-02-01

To assess the effectiveness of a one-stage lengthening using a locked nail technique for the treatment of distal femoral shaft nonunions associated with shortening. Retrospective. University hospital. During a 6-year period, 36 distal femoral shaft nonunions associated with shortening (>1.5 cm) were treated by the one-stage lengthening technique. Indications for this technique were distal femoral shaft aseptic or quiescent infected nonunions, 1.5-5 cm shortening, and a fracture level suitable for the insertion of two distal locked screws. The surgical technique involved skeletal traction using the femoral condyle, local débridement, lengthening by lengthening was 2.5 cm (range 1.5-3.5 cm). One-stage lengthening using the locked nailing technique to treat distal femoral shaft nonunions associated with shortening can achieve a high success rate and low complication rate. The key to successful treatment is the patient's complete cooperation with strictly protected weight bearing until the fracture has healed.

From zinc selenate to zinc selenide nano structures synthesized by reduction process

International Nuclear Information System (INIS)

Hutagalung, S.D.; Eng, S.T.; Ahmad, Z.A.; Ishak Mat; Yussof Wahab

2009-01-01

One-dimensional nano structure materials are very attractive because of their electronic and optical properties depending on their size. It is well known that properties of material can be tuned by reducing size to nano scale because at the small sizes, that they behave differently with its bulk materials and the band gap will control by the size. The tunability of the band gap makes nano structured materials useful for many applications. As one of the wide band gaps semiconductor compounds, zinc selenide (ZnSe) nano structures (nanoparticles, nano wires, nano rods) have received much attention for the application in optoelectronic devices, such as blue laser diode, light emitting diodes, solar cells and IR optical windows. In this study, ZnSe nano structures have been synthesized by reduction process of zinc selenate using hydrazine hydrate (N 2 H 4 .2H 2 O). The reductive agent of hydrazine hydrate was added to the starting materials of zinc selenate were heat treated at 500 degree Celsius for 1 hour under argon flow to form one-dimensional nano structures. The SEM and TEM images show the formation of nano composite-like structure, which some small nano bar and nano pellets stick to the rod. The x-ray diffraction and elemental composition analysis confirm the formation of mixture zinc oxide and zinc selenide phases. (author)

Two-stage implant systems.

Science.gov (United States)

Fritz, M E

1999-06-01

Since the advent of osseointegration approximately 20 years ago, there has been a great deal of scientific data developed on two-stage integrated implant systems. Although these implants were originally designed primarily for fixed prostheses in the mandibular arch, they have been used in partially dentate patients, in patients needing overdentures, and in single-tooth restorations. In addition, this implant system has been placed in extraction sites, in bone-grafted areas, and in maxillary sinus elevations. Often, the documentation of these procedures has lagged. In addition, most of the reports use survival criteria to describe results, often providing overly optimistic data. It can be said that the literature describes a true adhesion of the epithelium to the implant similar to adhesion to teeth, that two-stage implants appear to have direct contact somewhere between 50% and 70% of the implant surface, that the microbial flora of the two-stage implant system closely resembles that of the natural tooth, and that the microbiology of periodontitis appears to be closely related to peri-implantitis. In evaluations of the data from implant placement in all of the above-noted situations by means of meta-analysis, it appears that there is a strong case that two-stage dental implants are successful, usually showing a confidence interval of over 90%. It also appears that the mandibular implants are more successful than maxillary implants. Studies also show that overdenture therapy is valid, and that single-tooth implants and implants placed in partially dentate mouths have a success rate that is quite good, although not quite as high as in the fully edentulous dentition. It would also appear that the potential causes of failure in the two-stage dental implant systems are peri-implantitis, placement of implants in poor-quality bone, and improper loading of implants. There are now data addressing modifications of the implant surface to alter the percentage of

Considerations Regarding Age at Surgery and Fistula Incidence Using One- and Two-stage Closure for Cleft Palate

Directory of Open Access Journals (Sweden)

Simona Stoicescu

2013-12-01

Full Text Available Introduction: Although cleft lip and palate (CLP is one of the most common congenital malformations, occurring in 1 in 700 live births, there is still no generally accepted treatment protocol. Numerous surgical techniques have been described for cleft palate repair; these techniques can be divided into one-stage (one operation cleft palate repair and two-stage cleft palate closure. The aim of this study is to present our cleft palate team experience in using the two-stage cleft palate closure and the clinical outcomes in terms of oronasal fistula rate. Material and methods: A retrospective analysis was performed on medical records of 80 patients who underwent palate repair over a five-year period, from 2008 to 2012. All cleft palate patients were incorporated. Information on patient’s gender, cleft type, age at repair, one- or two-stage cleft palate repair were collected and analyzed. Results: Fifty-three (66% and twenty-seven (34% patients underwent two-stage and one-stage repair, respectively. According to Veau classification, more than 60% of them were Veau III and IV, associating cleft lip to cleft palate. Fistula occurred in 34% of the two-stage repairs versus 7% of one-stage repairs, with an overall incidence of 24%. Conclusions: Our study has shown that a two-stage cleft palate closure has a higher rate of fistula formation when compared with the one-stage repair. Two-stage repair is the protocol of choice in wide complete cleft lip and palate cases, while one-stage procedure is a good option for cleft palate alone, or some specific cleft lip and palate cases (narrow cleft palate, older age at surgery

Two-step two-stage fission gas release model

International Nuclear Information System (INIS)

Kim, Yong-soo; Lee, Chan-bock

2006-01-01

Based on the recent theoretical model, two-step two-stage model is developed which incorporates two stage diffusion processes, grain lattice and grain boundary diffusion, coupled with the two step burn-up factor in the low and high burn-up regime. FRAPCON-3 code and its in-pile data sets have been used for the benchmarking and validation of this model. Results reveals that its prediction is in better agreement with the experimental measurements than that by any model contained in the FRAPCON-3 code such as ANS 5.4, modified ANS5.4, and Forsberg-Massih model over whole burn-up range up to 70,000 MWd/MTU. (author)

Single-stage Acetabular Revision During Two-stage THA Revision for Infection is Effective in Selected Patients.

Science.gov (United States)

Fink, Bernd; Schlumberger, Michael; Oremek, Damian

2017-08-01

patients were assessed before surgery, between stages, every 3 months during the first year after surgery, every 6 months during the second year postoperative, and at latest followup, and were retrospectively drawn from a longitudinally maintained institutional database. Thirty-four of 35 patients (97.2%; 95% CI, 85.4%-99.5%) appeared free of infection by criteria of Masri et al. and Zimmerli et al. at latest followup. The Harris hip score was 61 ± 13 points after the first operation and 82 ± 16 points 2 years after the second operation. This technique is a promising treatment option for periprosthetic infections of the hip in which substantial acetabular defects exclude implantation of a normal spacer and a two-stage revision of the femoral component is favored. Level IV, therapeutic study.

Two-stage revision of septic knee prosthesis with articulating knee spacers yields better infection eradication rate than one-stage or two-stage revision with static spacers.

Science.gov (United States)

Romanò, C L; Gala, L; Logoluso, N; Romanò, D; Drago, L

2012-12-01

The best method for treating chronic periprosthetic knee infection remains controversial. Randomized, comparative studies on treatment modalities are lacking. This systematic review of the literature compares the infection eradication rate after two-stage versus one-stage revision and static versus articulating spacers in two-stage procedures. We reviewed full-text papers and those with an abstract in English published from 1966 through 2011 that reported the success rate of infection eradication after one-stage or two-stage revision with two different types of spacers. In all, 6 original articles reporting the results after one-stage knee exchange arthoplasty (n = 204) and 38 papers reporting on two-stage revision (n = 1,421) were reviewed. The average success rate in the eradication of infection was 89.8% after a two-stage revision and 81.9% after a one-stage procedure at a mean follow-up of 44.7 and 40.7 months, respectively. The average infection eradication rate after a two-stage procedure was slightly, although significantly, higher when an articulating spacer rather than a static spacer was used (91.2 versus 87%). The methodological limitations of this study and the heterogeneous material in the studies reviewed notwithstanding, this systematic review shows that, on average, a two-stage procedure is associated with a higher rate of eradication of infection than one-stage revision for septic knee prosthesis and that articulating spacers are associated with a lower recurrence of infection than static spacers at a comparable mean duration of follow-up. IV.

Uptake and specification of selenium in garlic cultivated in soil amended with symbiotic fungi (mycorrhiza) and selenate

NARCIS (Netherlands)

Larsen, E.H.; Lobinski, R.; Burger-Meijer, K.; Hansen, M.; Ruzik, R.; Mazurowska, L.; Rasmussen, P.H.; Sloth, J.J.; Scholten, O.E.; Kik, C.

2006-01-01

The scope of the work was to investigate the influence of selenate fertilisation and the addition of symbiotic fungi (mycorrhiza) to soil on selenium and selenium species concentrations in garlic. The selenium species were extracted from garlic cultivated in experimental plots by proteolytic

Synthesis and crystal structure of a new neodymium(III) selenate-selenite: Nd2(SeO4)(SeO3)2(H2O)2

International Nuclear Information System (INIS)

Feng Meiling; Mao Jianggao

2005-01-01

The title new neodymium(III) selenate-selenite was obtained by hydrothermal reactions of neodymium(III) oxide, H 2 SeO 4 and 1,10-phenanthroline at 140 o C. Its structure was established by single-crystal X-ray diffraction. The title compound crystallizes in the monoclinic space group C2/c with cell parameters of a = 12.258(2) A, b 7.1024(15) A, c = 13.391(3) A, β = 104.250(2) o . The structure of Nd 2 (SeO 4 )(SeO 3 ) 2 (H 2 O) 2 is isomorphous with that of Er 2 (SeO 4 )(SeO 3 ) 2 (H 2 O) 2 , which was refined in the monoclinic space group C2 with the disordered selenate group. It features an ordered 3D network with channels along b-axis. The selenate or selenite groups alone can form a 2D layer with the Nd(III) ions. IR spectrum, TGA and luminescent studies have also been performed

Two stages of economic development

OpenAIRE

Gong, Gang

2016-01-01

This study suggests that the development process of a less-developed country can be divided into two stages, which demonstrate significantly different properties in areas such as structural endowments, production modes, income distribution, and the forces that drive economic growth. The two stages of economic development have been indicated in the growth theory of macroeconomics and in the various "turning point" theories in development economics, including Lewis's dual economy theory, Kuznet...

Determination of Proteinaceous Selenocysteine in Selenized Yeast

Directory of Open Access Journals (Sweden)

Katarzyna Bierla

2018-02-01

Full Text Available A method for the quantitation of proteinaceous selenocysteine (SeCys in Se-rich yeast was developed. The method is based on the reduction of the Se-Se and S-Se bridges with dithiotretiol, derivatization with iodoacetamide (carbamidomethylation, followed by HPLC-ICP MS. The chromatographic conditions were optimized for the total recovery of the proteinaceous selenocysteine, the minimum number of peaks in the chromatogram (reduction of derivatization products of other Se-species present and the baseline separation. A typical chromatogram of a proteolytic digest of selenized yeast protein consisted of up to five peaks (including SeMet, carbamidomethylated (CAM-SeCys, and Se(CAM2 identified by retention time matching with available standards and electrospray MS. Inorganic selenium non-specifically attached to proteins and selenomethionine could be quantified (in the form of Se(CAM2 along with SeCys. Selenocysteine, selenomethionine, inorganic selenium, and the water soluble-metabolite fraction accounted for the totality of selenium species in Se-rich yeast.

Two stage treatment of dairy effluent using immobilized Chlorella pyrenoidosa

Science.gov (United States)

2013-01-01

Background Dairy effluents contains high organic load and unscrupulous discharge of these effluents into aquatic bodies is a matter of serious concern besides deteriorating their water quality. Whilst physico-chemical treatment is the common mode of treatment, immobilized microalgae can be potentially employed to treat high organic content which offer numerous benefits along with waste water treatment. Methods A novel low cost two stage treatment was employed for the complete treatment of dairy effluent. The first stage consists of treating the diary effluent in a photobioreactor (1 L) using immobilized Chlorella pyrenoidosa while the second stage involves a two column sand bed filtration technique. Results Whilst NH4+-N was completely removed, a 98% removal of PO43--P was achieved within 96 h of two stage purification processes. The filtrate was tested for toxicity and no mortality was observed in the zebra fish which was used as a model at the end of 96 h bioassay. Moreover, a significant decrease in biological oxygen demand and chemical oxygen demand was achieved by this novel method. Also the biomass separated was tested as a biofertilizer to the rice seeds and a 30% increase in terms of length of root and shoot was observed after the addition of biomass to the rice plants. Conclusions We conclude that the two stage treatment of dairy effluent is highly effective in removal of BOD and COD besides nutrients like nitrates and phosphates. The treatment also helps in discharging treated waste water safely into the receiving water bodies since it is non toxic for aquatic life. Further, the algal biomass separated after first stage of treatment was highly capable of increasing the growth of rice plants because of nitrogen fixation ability of the green alga and offers a great potential as a biofertilizer. PMID:24355316

How the Starting Precursor Influences the Properties of Polycrystalline CuInGaSe2 Thin Films Prepared by Sputtering and Selenization

Directory of Open Access Journals (Sweden)

Greta Rosa

2016-05-01

Full Text Available Cu(In,GaSe2 (CIGS/CdS thin-film solar cells have reached, at laboratory scale, an efficiency higher than 22.3%, which is one of the highest efficiencies ever obtained for thin-film solar cells. The research focus has now shifted onto fabrication processes, which have to be easily scalable at an industrial level. For this reason, a process is highlighted here which uses only the sputtering technique for both the absorber preparation and the deposition of all the other materials that make up the cell. Particular emphasis is placed on the comparison between different precursors obtained with either In2Se3 and Ga2Se3 or InSe and GaSe as starting materials. In both cases, the precursor does not require any heat treatment, and it is immediately ready to be selenized. The selenization is performed in a pure-selenium atmosphere and only lasts a few minutes at a temperature of about 803 K. Energy conversion efficiencies in the range of 15%–16% are reproducibly obtained on soda-lime glass (SLG substrates. Similar results are achieved if commercial ceramic tiles are used as a substrate instead of glass. This result is especially useful for the so-called building integrated photovoltaic. Cu(In,GaSe2-based solar cells grown directly on ceramic tiles are ideal for the fabrication of ventilated façades in low impact buildings.

Comparison of single-stage and temperature-phased two-stage anaerobic digestion of oily food waste

International Nuclear Information System (INIS)

Wu, Li-Jie; Kobayashi, Takuro; Li, Yu-You; Xu, Kai-Qin

2015-01-01

Highlights: • A single-stage and two two-stage anaerobic systems were synchronously operated. • Similar methane production 0.44 L/g VS_a_d_d_e_d from oily food waste was achieved. • The first stage of the two-stage process became inefficient due to serious pH drop. • Recycle favored the hythan production in the two-stage digestion. • The conversion of unsaturated fatty acids was enhanced by recycle introduction. - Abstract: Anaerobic digestion is an effective technology to recover energy from oily food waste. A single-stage system and temperature-phased two-stage systems with and without recycle for anaerobic digestion of oily food waste were constructed to compare the operation performances. The synchronous operation indicated the similar ability to produce methane in the three systems, with a methane yield of 0.44 L/g VS_a_d_d_e_d. The pH drop to less than 4.0 in the first stage of two-stage system without recycle resulted in poor hydrolysis, and methane or hydrogen was not produced in this stage. Alkalinity supplement from the second stage of two-stage system with recycle improved pH in the first stage to 5.4. Consequently, 35.3% of the particulate COD in the influent was reduced in the first stage of two-stage system with recycle according to a COD mass balance, and hydrogen was produced with a percentage of 31.7%, accordingly. Similar solids and organic matter were removed in the single-stage system and two-stage system without recycle. More lipid degradation and the conversion of long-chain fatty acids were achieved in the single-stage system. Recycling was proved to be effective in promoting the conversion of unsaturated long-chain fatty acids into saturated fatty acids in the two-stage system.

Preparation of CIGS thin films by HiPIMS or DC sputtering and various selenization processes

Czech Academy of Sciences Publication Activity Database

Olejníček, Jiří; Hubička, Zdeněk; Kšírová, Petra; Kment, Štěpán; Brunclíková, Michaela; Kohout, Michal; Čada, Martin; Darveau, S.A.; Exstrom, C.L.

2013-01-01

Roč. 16, č. 2 (2013), s. 314-319 ISSN 1203-8407 R&D Projects: GA MŠk LH12045 Institutional support: RVO:68378271 Keywords : CIGS * HIPIMS * selenization * nanocrystals * solar energy * sputtering * thin films Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 1.106, year: 2013 http://www.ingentaconnect.com/content/stn/jaots/2013/00000016/00000002/art00015

Two-Stage Centrifugal Fan

Science.gov (United States)

Converse, David

2011-01-01

Fan designs are often constrained by envelope, rotational speed, weight, and power. Aerodynamic performance and motor electrical performance are heavily influenced by rotational speed. The fan used in this work is at a practical limit for rotational speed due to motor performance characteristics, and there is no more space available in the packaging for a larger fan. The pressure rise requirements keep growing. The way to ordinarily accommodate a higher DP is to spin faster or grow the fan rotor diameter. The invention is to put two radially oriented stages on a single disk. Flow enters the first stage from the center; energy is imparted to the flow in the first stage blades, the flow is redirected some amount opposite to the direction of rotation in the fixed stators, and more energy is imparted to the flow in the second- stage blades. Without increasing either rotational speed or disk diameter, it is believed that as much as 50 percent more DP can be achieved with this design than with an ordinary, single-stage centrifugal design. This invention is useful primarily for fans having relatively low flow rates with relatively high pressure rise requirements.

Staged closure of a giant omphalocele with amnion preservation, modified technique

Directory of Open Access Journals (Sweden)

Akram H. Aljahdali

2017-04-01

Full Text Available Closure of a giant omphalocele can be challenging. Preservation of the amnion in staged closure is not commonly practiced. Here, we describe 2 cases of giant omphalocele treated with a modified amnion preservation, staged closure technique. This paper demonstrates the feasibility and safety of this technique, and the versatility of amnion to adapt to an escharization strategy if closure is not achievable.

Effects of pushing techniques during the second stage of labor: A randomized controlled trial

Directory of Open Access Journals (Sweden)

Refika Genç Koyucu

2017-10-01

Conclusions: Although the duration of the second stage of labor was longer compared to valsalva pushing technique, women were able to give birth without requiring any verbal or visual instruction, without exceeding the limit value of two hours and without affecting fetal wellness and neonatal results.

Synthesis, characterization and thermal decomposition of tetramethylammonium rare earth double selenates

Science.gov (United States)

Divekar, Sandesh K.; Achary, S. Nagabhusan; Ajgaonkar, Vishnu R.

2018-06-01

A series of double selenates, as (CH3)4NLn(SeO4)2rad 4H2O (Ln = Rare earth ion like La, Pr, Nd, Sm, Gd, Tb, Dy) was crystallized from mixed solution and characterized in detail for their structure, vibrational and optical properties as well as thermal stabilities. The crystal structure of the praseodymium compound was obtained by single crystal X-ray diffraction (XRD) and revealed a monoclinic (C2/c) lattice with chains formed by PrO8 and SeO4 units. The chains with compositions [Pr(SeO4)4(H2O)4]- are stacked in three dimensions and the (CH3)4N+ ions located in between them provide charge neutrality to the structure. The characterization of other compounds were carried out from powder XRD data and revealed that they all are isostructural to Pr-compound. All the functional groups were identified by Raman and IR spectroscopic studies. Solid state 77Se NMR revealed noticeable changes in selenium environment in these compounds. The optical absorption studies on the compounds show strong band edge absorptions in UV region. Thermal stabilities of the compounds, as investigated by simultaneous TG-DTA techniques indicate their sequential decompositions due to loss of H2O, (CH3)4N+ group, SeO2 and finally leaving their corresponding rare earth oxides.

Single Stage Silicone Border Molded Closed Mouth Impression Technique-Part II.

Science.gov (United States)

Solomon, E G R

2011-09-01

Functioning of a complete denture depends to a great extent on the impression technique. Several impression techniques have been described in the literature since the turn of this century when Greene [Clinical courses in dental prothesis, 1916] brothers introduced the first scientific system of recording dental impression. Advocates of each technique have their own claim of superiority over the other. The introduction of elastomeric impression materials [Skinner and Cooper, J Am Dent Assoc 51:523-536, 1955] has made possible new techniques of recording impression for complete denture construction. These rubber like materials are of two types; one has a polysulfide base and is popularily known as polysulfide rubber (Thiokol and Mercaptan). The other variety has a silicone base known as silicone rubber or silicone elastomer. Silicone elastomers are available in four different consistencies; a thin easy flowing light bodied material,a creamy medium bodied material, a highly viscous heavy bodied material and a kneadable putty material. This paper describes an active closed mouth impression technique with one stage border molding using putty silicone material as a substitute for low fusing compound.

Synthesis and crystal structure of hydrogen selenates K(HSeO4)(H2SeO4) and Cs(HSeO4)(H2SeO4)

International Nuclear Information System (INIS)

Troyanov, S.I.; Morozov, I.V.; Zakharov, M.A.; Kemnitz, E.

1999-01-01

Hydrogen selenates of the compositions K(HSeO 4 )(H 2 SeO 4 ) and Cs(HSeO 4 )(H 2 SeO 4 ) are synthesized by the reaction of alkali metal carbonates with an excess of the concentrated selenic acid. The X-ray diffraction study showed that both compounds are isostructural to the corresponding hydrogen sulfates. The difference in the systems of hydrogen bonding are caused by various combinations of the acceptor functions of the oxygen atoms in the HSeO 4 and H 2 SeO 4 groups

Infrared absorption spectra of selenate compounds of indium (3)

International Nuclear Information System (INIS)

Kharitonov, Yu.Ya.; Kadoshnikova, N.V.; Tananaev, I.V.

1979-01-01

Obtained and discussed are infrared absorption spectra (400-4000 cm -1 ) of the following indium selenates: In 2 (SeO 4 ) 3 x5H 2 O, In 2 (SeO 4 ) 3 x9H 2 O, NaIn(SeO 4 ) 2 x6H 2 O, NaIn(SeO 4 ) 2 xH 2 O, MIn(SeO 4 ) 2 x4H 2 O (M=NH 4 , K, Rb), CsIn(SeO 4 ) 2 x2H 2 O, Na 3 In(SeO 4 ) 3 x7H 2 O, MIn(SeO 4 ) 2 (M=NH 4 , Na, K, Rb, Cs), M 2 InOH(SeO 4 ) 2 xyH 2 O (M=NH 4 , Na, K, Rb) and K 2 InOD(SeO 4 ) 2 xyD 2 O

Forensic age estimation based on development of third molars: a staging technique for magnetic resonance imaging.

Science.gov (United States)

De Tobel, J; Phlypo, I; Fieuws, S; Politis, C; Verstraete, K L; Thevissen, P W

2017-12-01

The development of third molars can be evaluated with medical imaging to estimate age in subadults. The appearance of third molars on magnetic resonance imaging (MRI) differs greatly from that on radiographs. Therefore a specific staging technique is necessary to classify third molar development on MRI and to apply it for age estimation. To develop a specific staging technique to register third molar development on MRI and to evaluate its performance for age estimation in subadults. Using 3T MRI in three planes, all third molars were evaluated in 309 healthy Caucasian participants from 14 to 26 years old. According to the appearance of the developing third molars on MRI, descriptive criteria and schematic representations were established to define a specific staging technique. Two observers, with different levels of experience, staged all third molars independently with the developed technique. Intra- and inter-observer agreement were calculated. The data were imported in a Bayesian model for age estimation as described by Fieuws et al. (2016). This approach adequately handles correlation between age indicators and missing age indicators. It was used to calculate a point estimate and a prediction interval of the estimated age. Observed age minus predicted age was calculated, reflecting the error of the estimate. One-hundred and sixty-six third molars were agenetic. Five percent (51/1096) of upper third molars and 7% (70/1044) of lower third molars were not assessable. Kappa for inter-observer agreement ranged from 0.76 to 0.80. For intra-observer agreement kappa ranged from 0.80 to 0.89. However, two stage differences between observers or between staging sessions occurred in up to 2.2% (20/899) of assessments, probably due to a learning effect. Using the Bayesian model for age estimation, a mean absolute error of 2.0 years in females and 1.7 years in males was obtained. Root mean squared error equalled 2.38 years and 2.06 years respectively. The performance to

A two-stage flow-based intrusion detection model for next-generation networks.

Science.gov (United States)

Umer, Muhammad Fahad; Sher, Muhammad; Bi, Yaxin

2018-01-01

The next-generation network provides state-of-the-art access-independent services over converged mobile and fixed networks. Security in the converged network environment is a major challenge. Traditional packet and protocol-based intrusion detection techniques cannot be used in next-generation networks due to slow throughput, low accuracy and their inability to inspect encrypted payload. An alternative solution for protection of next-generation networks is to use network flow records for detection of malicious activity in the network traffic. The network flow records are independent of access networks and user applications. In this paper, we propose a two-stage flow-based intrusion detection system for next-generation networks. The first stage uses an enhanced unsupervised one-class support vector machine which separates malicious flows from normal network traffic. The second stage uses a self-organizing map which automatically groups malicious flows into different alert clusters. We validated the proposed approach on two flow-based datasets and obtained promising results.

Optimization of Boiling Water Reactor Loading Pattern Using Two-Stage Genetic Algorithm

International Nuclear Information System (INIS)

Kobayashi, Yoko; Aiyoshi, Eitaro

2002-01-01

A new two-stage optimization method based on genetic algorithms (GAs) using an if-then heuristic rule was developed to generate optimized boiling water reactor (BWR) loading patterns (LPs). In the first stage, the LP is optimized using an improved GA operator. In the second stage, an exposure-dependent control rod pattern (CRP) is sought using GA with an if-then heuristic rule. The procedure of the improved GA is based on deterministic operators that consist of crossover, mutation, and selection. The handling of the encoding technique and constraint conditions by that GA reflects the peculiar characteristics of the BWR. In addition, strategies such as elitism and self-reproduction are effectively used in order to improve the search speed. The LP evaluations were performed with a three-dimensional diffusion code that coupled neutronic and thermal-hydraulic models. Strong axial heterogeneities and constraints dependent on three dimensions have always necessitated the use of three-dimensional core simulators for BWRs, so that optimization of computational efficiency is required. The proposed algorithm is demonstrated by successfully generating LPs for an actual BWR plant in two phases. One phase is only LP optimization applying the Haling technique. The other phase is an LP optimization that considers the CRP during reactor operation. In test calculations, candidates that shuffled fresh and burned fuel assemblies within a reasonable computation time were obtained

Two-stage distraction lengthening of the forearm.

Science.gov (United States)

Taghinia, Amir H; Al-Sheikh, Ayman A; Panossian, Andre E; Upton, Joseph

2013-01-01

Single-stage lengthening of the forearm using callus distraction is well described; however, forearm lengthening using a 2-stage technique of distraction followed by bone grafting has received less attention. A 2-staged technique can be a better alternative in cases where the surgeon desires extensive lengthening. A retrospective review was undertaken of eleven 2-stage forearm lengthening procedures performed by 1 surgeon over a 15-year period. Indications were radial longitudinal deficiency (8 patients), neonatal ischemic contractures (2 patients), and septic growth arrest (1 patient). Average follow-up was 2.8 years. Distraction was performed on patients an average of 82 mm over an average duration of 24 weeks. Average time to union from the time of distractor removal and grafting was 87 days. Average healing index was 32.1 d/cm. Distraction problems were common and related to the length of time that the distractor was in place; they included pain, pin-related infections, and multiple mechanical device difficulties. Three patients had nonunion, and another had delayed union; however, additional procedures resulted in ultimate bony union in all patients. Demineralized bone matrix and autologous corticocancellous bone grafts yielded predictable healing and good functional results in short-distance distractions. For longer distractions, free vascularized fibula transfer produced the best outcomes. Intercalary cortical allografts did not heal well. Patients with neonatal Volkmann contractures had the most difficulty with distraction and healing, ultimately obtaining little to no lengthening and poor functional outcomes.

Hazard assessment of inorganics to three endangered fish in the Green River, Utah

Science.gov (United States)

Hamilton, S.J.

1995-01-01

Acute toxicity tests were conducted with three life stages of Colorado squawfish (Ptychocheilus lucius), razorback sucker (Xyrauchen texanus), and bonytail (Gila elegans) in a reconstituted water quality simulating the middle part of the Green River of Utah. Tests were conducted with boron, lithium, selenate, selenite, uranium, vanadium, and zinc. The overall rank order of toxicity to all species and life stages combined from most to least toxic was vanadium = zinc > selenite > lithium = uranium > selenate > boron. There was no difference between the three species in their sensitivity to the seven inorganics based on a rank-order evaluation at the species level. Colorado squawfish were 2-5 times more sensitive to selenate and selenite at the swimup life stage than older stages, whereas razorback suckers displayed equal sensitivity among life stages. Bonytail exhibited equal sensitivity to selenite, but were five times more sensitive to selenate at the swimup life stage than the older stages. Comparison of 96-hr LC50 values with a limited number of environmental water concentrations in Ashley Creek, Utah, which receives irrigation drainwater, revealed moderate hazard ratios for boron, selenate, selenite, and zinc, low hazard ratios for uranium and vanadium, but unknown ratios for lithium. These inorganic contaminants in drainwaters may adversely affect endangered fish in the Green River.

Two-stage free electron laser research

Science.gov (United States)

Segall, S. B.

1984-10-01

KMS Fusion, Inc. began studying the feasibility of two-stage free electron lasers for the Office of Naval Research in June, 1980. At that time, the two-stage FEL was only a concept that had been proposed by Luis Elias. The range of parameters over which such a laser could be successfully operated, attainable power output, and constraints on laser operation were not known. The primary reason for supporting this research at that time was that it had the potential for producing short-wavelength radiation using a relatively low voltage electron beam. One advantage of a low-voltage two-stage FEL would be that shielding requirements would be greatly reduced compared with single-stage short-wavelength FEL's. If the electron energy were kept below about 10 MeV, X-rays, generated by electrons striking the beam line wall, would not excite neutron resonance in atomic nuclei. These resonances cause the emission of neutrons with subsequent induced radioactivity. Therefore, above about 10 MeV, a meter or more of concrete shielding is required for the system, whereas below 10 MeV, a few millimeters of lead would be adequate.

Investigation of stacked elemental layers for Cu(In,Ga)Se{sub 2} thin film preparation by rapid thermal selenization

Energy Technology Data Exchange (ETDEWEB)

Stroth, Christiane; Ohland, Joerg; Mikolajczak, Ulf; Madena, Thomas; Keller, Jan; Parisi, Juergen; Hammer, Maria; Riedel, Ingo [Energy and Semiconductor Research Laboratory, Department of Physics, University of Oldenburg, 26111 Oldenburg (Germany)

2013-07-01

Rapid thermal selenization of pure metallic (Cu-In-Ga) or selenium-containing (Cu-In-Ga-Se) precursors is a favorable method to fabricate Cu(In,Ga)Se{sub 2} absorber films for application in thin film solar cells. Because of its upscaling potential and the short process time it is a promising approach for the fabrication of CIGSe photovoltaic modules on industrial scale. As a preliminary work for prospective plasma-enhanced selenization of stacked elemental layers (SEL) the elements copper, indium and gallium were sequentially deposited on molybdenum coated soda-lime glass by thermal evaporation. The stacking order was varied and the precursors were annealed with different heating rates. Morphology, elemental depth distribution and phases of the layers were investigated before and after annealing using scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction. Furthermore the influence of different heating rates on phase transitions during annealing was studied by in-situ X-ray diffraction.

A two-stage value chain model for vegetable marketing chain efficiency evaluation: A transaction cost approach

OpenAIRE

Lu Hualiang

2006-01-01

We applied a two-stage value chain model to investigate the effects of input application and occasional transaction costs on vegetable marketing chain efficiencies with a farm household-level data set. In the first stage, the production efficiencies with the combination of resource endowments, capital and managerial inputs, and production techniques were evaluated; then at the second stage, the marketing technical efficiencies were determined under the marketing value of the vegetables for th...

Prognosis of endometrial carcinoma stage I in two Swedish regions

International Nuclear Information System (INIS)

Sorbe, B.; Kjellgren, O.; Stenson, S.; Umeaa Univ. Hospital; Uppsala Univ.

1990-01-01

A high dose-rate afterloading technique ( 60 Co) was compared with a low dose-rate packing method ( 226 Ra) in the treatment of endometrical carcinoma stage I. In all, 1021 patients treated during the period 1977-1986 at two Swedish gynecologic oncology centers were analyzed regarding treatment set-up, histopathologic outcome in the operative specimens, recurrence rates, survival rates and radiation side effects. Complete tumor eradication in the operative specimen was achieved in 80% after radium therapy and in 60% after irradiation by the high dose-rate technique. The overall recurrence rate was 15.7% in the radium packing series and 11.5% after cobalt afterloading treatment. The risk of pelvic recurrences increased by 2.1-2.6 if hysterectomy was replaced by dilatation and curettage. The two radiation techniques seemed t be comparable with regard to the risk of both pelvic recurrences and distant metastases. The 5-year crude survival rates were 85% in the afterloading series and 82% in the radium series. The corrected survival rates were similar (90%) for the two techniques. Age, tumor grade and uterine size were significant prognostic factors with regard to the probability of death due to cancer. Early radiation reactions had quite similar rates in the two series, whereas late radiation reactions were more frequent in the high dose-rate afterloading group in the 10-12 Gy dose fraction range, but not in the 5-8 Gy range. The radium packing method seemed to give a higher frequency of tumor-free operative specimens in this study, but with regard to recurrence rates and survival probabilities the techniques were comparable. Since the different proportion of surgery in the two series and the histopathologic evaluation might have influenced the rate of local tumor eradication in the operative specimens and the risk of pelvic recurrences the results must be assessed with great caution and only a crude comparison of the two treatment techniques could be made. (orig.)

Syntheses, structures, and IR spectroscopic characterization of new uranyl sulfate/selenate 1D-chain, 2D-sheet and 3D-framework

Energy Technology Data Exchange (ETDEWEB)

Ling Jie; Sigmon, Ginger E.; Ward, Matthew; Roback, Nancy; Burns, Peter C. [Dept. of Civil Engineering and Geological Science, Univ. of Notre Dame, IN (United States)

2010-07-01

Three uranyl sulfates, (C{sub 6}H{sub 20}N{sub 4})[(UO{sub 2}){sub 2} . (SO{sub 4}){sub 4}(H{sub 2}O){sub 2}](H{sub 2}O){sub 6} (TETAUS), (C{sub 15}H{sub 14}N{sub 3})[(UO{sub 2}) . (SO{sub 4}){sub 2}](NO{sub 3})(H{sub 2}O){sub 2} (TPUS), and K{sub 2}[(UO{sub 2})(SO{sub 4}){sub 2}(H{sub 2}O)] . H{sub 2}O (KUS), and two uranyl selenates, K(H{sub 3}O)[(UO{sub 2}){sub 2} . (SeO{sub 4}){sub 3}(H{sub 2}O)](H{sub 2}O){sub 6} (KUSe) and (H{sub 3}O){sub 2}[(UO{sub 2}){sub 2}(SeO{sub 4}){sub 3} . (H{sub 2}O)] (USe), were synthesized by slow evaporation of aqueous solutions at room temperature. TETAUS crystallizes in space group P anti 1, a = 6.7186(5) A, b = 9.2625(7) A, c = 13.1078(9) A, {alpha} = 72.337(2) , {beta} = 89.198(2) , {gamma} = 70.037(1) , V = 726.89(9) A{sup 3}, Z = 1. TPUS is triclinic, P anti 1, a = 6.9732(7) A, b = 13.569(1) A, c = 13.641(1) A, {alpha} = 111.809(2) , {beta} = 102.386(2) , {gamma} = 93.833(2) , V = 1150.0(2) A{sup 3}, Z = 2. KUS is orthorhombic, Cmca, a = 12.171(2) A, b = 16.689(3) A, c = 10.997(2) A, V = 2233.8(6) A{sup 3}, Z = 8. These uranyl sulfates are built from infinite one-dimensional uranyl sulfate chains with different topologies. KUSe is monoclinic, P2{sub 1}/n, a = 14.715(1) A, b = 10.1557(7) A, c = 15.833(1) A, {beta} = 114.415(1) , V = 2154.5(3) A{sup 3}, Z = 4. Its structure is based on a two-dimensional uranyl selenate sheet. USe crystallizes in space group P2{sub 1}/c, a = 10.6124(2) A, b = 14.7717(3) A, c = 13.7139(3) A, {beta} = 96.989(1) , V = 2133.86(8) A{sup 3}, Z = 4, with a complex three-dimensional uranyl selenate framework containing channels extending in three directions. (orig.)

A stage is a stage is a stage: a direct comparison of two scoring systems.

Science.gov (United States)

Dawson, Theo L

2003-09-01

L. Kohlberg (1969) argued that his moral stages captured a developmental sequence specific to the moral domain. To explore that contention, the author compared stage assignments obtained with the Standard Issue Scoring System (A. Colby & L. Kohlberg, 1987a, 1987b) and those obtained with a generalized content-independent stage-scoring system called the Hierarchical Complexity Scoring System (T. L. Dawson, 2002a), on 637 moral judgment interviews (participants' ages ranged from 5 to 86 years). The correlation between stage scores produced with the 2 systems was .88. Although standard issue scoring and hierarchical complexity scoring often awarded different scores up to Kohlberg's Moral Stage 2/3, from his Moral Stage 3 onward, scores awarded with the two systems predominantly agreed. The author explores the implications for developmental research.

Two-stage thermal/nonthermal waste treatment process

International Nuclear Information System (INIS)

Rosocha, L.A.; Anderson, G.K.; Coogan, J.J.; Kang, M.; Tennant, R.A.; Wantuck, P.J.

1993-01-01

An innovative waste treatment technology is being developed in Los Alamos to address the destruction of hazardous organic wastes. The technology described in this report uses two stages: a packed bed reactor (PBR) in the first stage to volatilize and/or combust liquid organics and a silent discharge plasma (SDP) reactor to remove entrained hazardous compounds in the off-gas to even lower levels. We have constructed pre-pilot-scale PBR-SDP apparatus and tested the two stages separately and in combined modes. These tests are described in the report

A novel flow sensor based on resonant sensing with two-stage microleverage mechanism

Science.gov (United States)

Yang, B.; Guo, X.; Wang, Q. H.; Lu, C. F.; Hu, D.

2018-04-01

The design, simulation, fabrication, and experiments of a novel flow sensor based on resonant sensing with a two-stage microleverage mechanism are presented in this paper. Different from the conventional detection methods for flow sensors, two differential resonators are adopted to implement air flow rate transformation through two-stage leverage magnification. The proposed flow sensor has a high sensitivity since the adopted two-stage microleverage mechanism possesses a higher amplification factor than a single-stage microleverage mechanism. The modal distribution and geometric dimension of the two-stage leverage mechanism and hair are analyzed and optimized by Ansys simulation. A digital closed-loop driving technique with a phase frequency detector-based coordinate rotation digital computer algorithm is implemented for the detection and locking of resonance frequency. The sensor fabricated by the standard deep dry silicon on a glass process has a device dimension of 5100 μm (length) × 5100 μm (width) × 100 μm (height) with a hair diameter of 1000 μm. The preliminary experimental results demonstrate that the maximal mechanical sensitivity of the flow sensor is approximately 7.41 Hz/(m/s)2 at a resonant frequency of 22 kHz for the hair height of 9 mm and increases by 2.42 times as hair height extends from 3 mm to 9 mm. Simultaneously, a detection-limit of 3.23 mm/s air flow amplitude at 60 Hz is confirmed. The proposed flow sensor has great application prospects in the micro-autonomous system and technology, self-stabilizing micro-air vehicles, and environmental monitoring.

Multiobjective Two-Stage Stochastic Programming Problems with Interval Discrete Random Variables

Directory of Open Access Journals (Sweden)

S. K. Barik

2012-01-01

Full Text Available Most of the real-life decision-making problems have more than one conflicting and incommensurable objective functions. In this paper, we present a multiobjective two-stage stochastic linear programming problem considering some parameters of the linear constraints as interval type discrete random variables with known probability distribution. Randomness of the discrete intervals are considered for the model parameters. Further, the concepts of best optimum and worst optimum solution are analyzed in two-stage stochastic programming. To solve the stated problem, first we remove the randomness of the problem and formulate an equivalent deterministic linear programming model with multiobjective interval coefficients. Then the deterministic multiobjective model is solved using weighting method, where we apply the solution procedure of interval linear programming technique. We obtain the upper and lower bound of the objective function as the best and the worst value, respectively. It highlights the possible risk involved in the decision-making tool. A numerical example is presented to demonstrate the proposed solution procedure.

Effect of ammoniacal nitrogen on one-stage and two-stage anaerobic digestion of food waste

International Nuclear Information System (INIS)

Ariunbaatar, Javkhlan; Scotto Di Perta, Ester; Panico, Antonio; Frunzo, Luigi; Esposito, Giovanni; Lens, Piet N.L.; Pirozzi, Francesco

2015-01-01

Highlights: • Almost 100% of the biomethane potential of food waste was recovered during AD in a two-stage CSTR. • Recirculation of the liquid fraction of the digestate provided the necessary buffer in the AD reactors. • A higher OLR (0.9 gVS/L·d) led to higher accumulation of TAN, which caused more toxicity. • A two-stage reactor is more sensitive to elevated concentrations of ammonia. • The IC 50 of TAN for the AD of food waste amounts to 3.8 g/L. - Abstract: This research compares the operation of one-stage and two-stage anaerobic continuously stirred tank reactor (CSTR) systems fed semi-continuously with food waste. The main purpose was to investigate the effects of ammoniacal nitrogen on the anaerobic digestion process. The two-stage system gave more reliable operation compared to one-stage due to: (i) a better pH self-adjusting capacity; (ii) a higher resistance to organic loading shocks; and (iii) a higher conversion rate of organic substrate to biomethane. Also a small amount of biohydrogen was detected from the first stage of the two-stage reactor making this system attractive for biohythane production. As the digestate contains ammoniacal nitrogen, re-circulating it provided the necessary alkalinity in the systems, thus preventing an eventual failure by volatile fatty acids (VFA) accumulation. However, re-circulation also resulted in an ammonium accumulation, yielding a lower biomethane production. Based on the batch experimental results the 50% inhibitory concentration of total ammoniacal nitrogen on the methanogenic activities was calculated as 3.8 g/L, corresponding to 146 mg/L free ammonia for the inoculum used for this research. The two-stage system was affected by the inhibition more than the one-stage system, as it requires less alkalinity and the physically separated methanogens are more sensitive to inhibitory factors, such as ammonium and propionic acid

Staging of gastric adenocarcinoma using two-phase spiral CT: correlation with pathologic staging

International Nuclear Information System (INIS)

Seo, Tae Seok; Lee, Dong Ho; Ko, Young Tae; Lim, Joo Won

1998-01-01

To correlate the preoperative staging of gastric adenocarcinoma using two-phase spiral CT with pathologic staging. One hundred and eighty patients with gastric cancers confirmed during surgery underwent two-phase spiral CT, and were evaluated retrospectively. CT scans were obtained in the prone position after ingestion of water. Scans were performed 35 and 80 seconds after the start of infusion of 120mL of non-ionic contrast material with the speed of 3mL/sec. Five mm collimation, 7mm/sec table feed and 5mm reconstruction interval were used. T-and N-stage were determined using spiral CT images, without knowledge of the pathologic results. Pathologic staging was later compared with CT staging. Pathologic T-stage was T1 in 70 cases(38.9%), T2 in 33(18.3%), T3 in 73(40.6%), and T4 in 4(2.2%). Type-I or IIa elevated lesions accouted for 10 of 70 T1 cases(14.3%) and flat or depressed lesions(type IIb, IIc, or III) for 60(85.7%). Pathologic N-stage was NO in 85 cases(47.2%), N1 in 42(23.3%), N2 in 31(17.2%), and N3 in 22(12,2%). The detection rate of early gastric cancer using two-phase spiral CT was 100.0%(10 of 10 cases) among elevated lesions and 78.3%(47 of 60 cases) among flat or depressed lesions. With regard to T-stage, there was good correlation between CT image and pathology in 86 of 180 cases(47.8%). Overstaging occurred in 23.3%(42 of 180 cases) and understaging in 28.9%(52 of 180 cases). With regard to N-stage, good correlation between CT image and pathology was noted in 94 of 180 cases(52.2%). The rate of understaging(31.7%, 57 of 180 cases) was higher than that of overstaging(16.1%, 29 of 180 cases)(p<0.001). The detection rate of early gastric cancer using two-phase spiral CT was 81.4%, and there was no significant difference in detectability between elevated and depressed lesions. Two-phase spiral CT for determing the T-and N-stage of gastric cancer was not effective;it was accurate in abont 50% of cases understaging tended to occur.=20

Frequency analysis of a two-stage planetary gearbox using two different methodologies

Science.gov (United States)

Feki, Nabih; Karray, Maha; Khabou, Mohamed Tawfik; Chaari, Fakher; Haddar, Mohamed

2017-12-01

This paper is focused on the characterization of the frequency content of vibration signals issued from a two-stage planetary gearbox. To achieve this goal, two different methodologies are adopted: the lumped-parameter modeling approach and the phenomenological modeling approach. The two methodologies aim to describe the complex vibrations generated by a two-stage planetary gearbox. The phenomenological model describes directly the vibrations as measured by a sensor fixed outside the fixed ring gear with respect to an inertial reference frame, while results from a lumped-parameter model are referenced with respect to a rotating frame and then transferred into an inertial reference frame. Two different case studies of the two-stage planetary gear are adopted to describe the vibration and the corresponding spectra using both models. Each case presents a specific geometry and a specific spectral structure.

Effects of pushing techniques during the second stage of labor: A randomized controlled trial.

Science.gov (United States)

Koyucu, Refika Genç; Demirci, Nurdan

2017-10-01

Spontaneous pushing is a method that is used in the management of the second stage of labor and suggested to be more physiological for the mother and infant. The present study aims to evaluate the effects of pushing techniques on the mother and newborn. This randomized prospective study was performed between June 2013-March 2014 in a tertiary maternity clinic in Istanbul. 80 low risk, nulliparous cases were randomized to pushing groups. Valsalva pushing group was told to hold their breath while pushing. No visual-verbal instructions were given to spontaneous pushing group and they were encouraged to push without preventing respiration. Demographic data, second stage period, perineal laceration rates, fetal heart rate patterns, presence of meconium stained amniotic liquid, newborn APGAR scores, POP-Q examination and Q-tip test results were evaluated in these cases. The second stage of labor was significantly longer with spontaneous pushing. Decrease in Hb levels in valsalva pushing group was determined to be higher than spontaneous pushing group. An increased urethral mobility was observed in valsalva pushing group. Although the duration of the second stage of labor was longer compared to valsalva pushing technique, women were able to give birth without requiring any verbal or visual instruction, without exceeding the limit value of two hours and without affecting fetal wellness and neonatal results. Copyright © 2017. Published by Elsevier B.V.

Video: two novel endoscopic esophageal lengthening and reconstruction techniques.

Science.gov (United States)

Perretta, Silvana; Wall, James K; Dallemagne, Bernard; Harrison, Michael; Becmeur, François; Marescaux, Jacques

2011-10-01

Esophageal reconstruction presents a significant clinical challenge in patients ranging from neonates with long-gap esophageal atresia to adults after esophageal resection. Both gastric and colonic replacement conduits carry significant morbidity. As emerging organ-sparring techniques become established for early stage esophageal tumors, less morbid reconstruction techniques are warranted. We present two novel endoscopic approaches for esophageal lengthening and reconstruction in a porcine model. Two models of esophageal defects were created in pigs (30-35 kg) under general anesthesia and subsequently reconstructed with the novel techniques. The first model was a segmental defect of the esophagus created by thoracoscopically transecting the esophagus above the gastroesophageal (GE) junction. The first reconstruction technique involved bilateral submucosal endoscopic lengthening myotomies (BSELM) with a magnetic compression anastomosis (MAGNAMOSIS™). The second model was a wedge defect in the anterior esophagus created above the GE junction through a laparotomy. The second reconstruction technique involved an inverted mucosal-submucosal sleeve transposition graft (IMSTG) that crossed the esophageal gap and was secured in place with a self-expandable covered esophageal stent. Both techniques were feasible in the pig model. The BSELM approach lengthened the esophagus 1 cm for every 2 cm length of myotomy. The myotomy targeted only the inner circular fibers of the esophagus, with preservation of the longitudinal layer to protect against long-term dilation and pouching. The IMSTG approach generated a vascularized mucosal graft almost as long as the esophagus itself. Emerging endoscopic capabilities are enabling complex endoluminal esophageal procedures. BSELM and IMSTG are two novel and technically feasible approaches to esophageal lengthening and reconstruction. Further survival studies are needed to establish the safety and efficacy of these techniques.

Two-Stage Fuzzy Portfolio Selection Problem with Transaction Costs

Directory of Open Access Journals (Sweden)

Yanju Chen

2015-01-01

Full Text Available This paper studies a two-period portfolio selection problem. The problem is formulated as a two-stage fuzzy portfolio selection model with transaction costs, in which the future returns of risky security are characterized by possibility distributions. The objective of the proposed model is to achieve the maximum utility in terms of the expected value and variance of the final wealth. Given the first-stage decision vector and a realization of fuzzy return, the optimal value expression of the second-stage programming problem is derived. As a result, the proposed two-stage model is equivalent to a single-stage model, and the analytical optimal solution of the two-stage model is obtained, which helps us to discuss the properties of the optimal solution. Finally, some numerical experiments are performed to demonstrate the new modeling idea and the effectiveness. The computational results provided by the proposed model show that the more risk-averse investor will invest more wealth in the risk-free security. They also show that the optimal invested amount in risky security increases as the risk-free return decreases and the optimal utility increases as the risk-free return increases, whereas the optimal utility increases as the transaction costs decrease. In most instances the utilities provided by the proposed two-stage model are larger than those provided by the single-stage model.

Wide-bandwidth bilateral control using two-stage actuator system

International Nuclear Information System (INIS)

Kokuryu, Saori; Izutsu, Masaki; Kamamichi, Norihiro; Ishikawa, Jun

2015-01-01

This paper proposes a two-stage actuator system that consists of a coarse actuator driven by a ball screw with an AC motor (the first stage) and a fine actuator driven by a voice coil motor (the second stage). The proposed two-stage actuator system is applied to make a wide-bandwidth bilateral control system without needing expensive high-performance actuators. In the proposed system, the first stage has a wide moving range with a narrow control bandwidth, and the second stage has a narrow moving range with a wide control bandwidth. By consolidating these two inexpensive actuators with different control bandwidths in a complementary manner, a wide bandwidth bilateral control system can be constructed based on a mechanical impedance control. To show the validity of the proposed method, a prototype of the two-stage actuator system has been developed and basic performance was evaluated by experiment. The experimental results showed that a light mechanical impedance with a mass of 10 g and a damping coefficient of 2.5 N/(m/s) that is an important factor to establish good transparency in bilateral control has been successfully achieved and also showed that a better force and position responses between a master and slave is achieved by using the proposed two-stage actuator system compared with a narrow bandwidth case using a single ball screw system. (author)

Two-stage precipitation of neptunium (IV) oxalate

International Nuclear Information System (INIS)

Luerkens, D.W.

1983-07-01

Neptunium (IV) oxalate was precipitated using a two-stage precipitation system. A series of precipitation experiments was used to identify the significant process variables affecting precipitate characteristics. Process variables tested were input concentrations, solubility conditions in the first stage precipitator, precipitation temperatures, and residence time in the first stage precipitator. A procedure has been demonstrated that produces neptunium (IV) oxalate particles that filter well and readily calcine to the oxide

Effect of ammoniacal nitrogen on one-stage and two-stage anaerobic digestion of food waste

Energy Technology Data Exchange (ETDEWEB)

Ariunbaatar, Javkhlan, E-mail: jaka@unicas.it [Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Via Di Biasio 43, 03043 Cassino, FR (Italy); UNESCO-IHE Institute for Water Education, Westvest 7, 2611 AX Delft (Netherlands); Scotto Di Perta, Ester [Department of Civil, Architectural and Environmental Engineering, University of Naples Federico II, Via Claudio 21, 80125 Naples (Italy); Panico, Antonio [Telematic University PEGASO, Piazza Trieste e Trento, 48, 80132 Naples (Italy); Frunzo, Luigi [Department of Mathematics and Applications Renato Caccioppoli, University of Naples Federico II, Via Claudio, 21, 80125 Naples (Italy); Esposito, Giovanni [Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Via Di Biasio 43, 03043 Cassino, FR (Italy); Lens, Piet N.L. [UNESCO-IHE Institute for Water Education, Westvest 7, 2611 AX Delft (Netherlands); Pirozzi, Francesco [Department of Civil, Architectural and Environmental Engineering, University of Naples Federico II, Via Claudio 21, 80125 Naples (Italy)

2015-04-15

Highlights: • Almost 100% of the biomethane potential of food waste was recovered during AD in a two-stage CSTR. • Recirculation of the liquid fraction of the digestate provided the necessary buffer in the AD reactors. • A higher OLR (0.9 gVS/L·d) led to higher accumulation of TAN, which caused more toxicity. • A two-stage reactor is more sensitive to elevated concentrations of ammonia. • The IC{sub 50} of TAN for the AD of food waste amounts to 3.8 g/L. - Abstract: This research compares the operation of one-stage and two-stage anaerobic continuously stirred tank reactor (CSTR) systems fed semi-continuously with food waste. The main purpose was to investigate the effects of ammoniacal nitrogen on the anaerobic digestion process. The two-stage system gave more reliable operation compared to one-stage due to: (i) a better pH self-adjusting capacity; (ii) a higher resistance to organic loading shocks; and (iii) a higher conversion rate of organic substrate to biomethane. Also a small amount of biohydrogen was detected from the first stage of the two-stage reactor making this system attractive for biohythane production. As the digestate contains ammoniacal nitrogen, re-circulating it provided the necessary alkalinity in the systems, thus preventing an eventual failure by volatile fatty acids (VFA) accumulation. However, re-circulation also resulted in an ammonium accumulation, yielding a lower biomethane production. Based on the batch experimental results the 50% inhibitory concentration of total ammoniacal nitrogen on the methanogenic activities was calculated as 3.8 g/L, corresponding to 146 mg/L free ammonia for the inoculum used for this research. The two-stage system was affected by the inhibition more than the one-stage system, as it requires less alkalinity and the physically separated methanogens are more sensitive to inhibitory factors, such as ammonium and propionic acid.

An optional focusing SELENE extension to conventional neutron guides: A case study for the ESS instrument BIFROST

Energy Technology Data Exchange (ETDEWEB)

Hansen, U.B., E-mail: uhansen@nbi.ku.dk [Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark); Bertelsen, M. [Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark); Stahn, J. [Laboratory for Neutron Scattering and Imaging, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Lefmann, K. [Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark)

2017-04-21

The high brilliance at the European Spallation Source (ESS) will allow for performing experiments with much smaller samples than at present neutron facilities and in much more complex sample environments. However the higher flux also results in higher background from unwanted neutrons not originating from scattering of the sample. We here present a new design idea for beam delivery, where a 165 m ballistic guide system with good transport properties is followed by a 4–8 m SELENE guide system similar to Montel optics used for X-ray optics. We have investigated the system by detailed Monte-Carlo simulations using McStas. We show that under certain conditions, this set-up works surprisingly well, with a brilliance transfer of 20–60% for neutrons of wavelength 4 Å and above. We demonstrate that the guide system is able to focus the beam almost perfectly onto samples sizes in the range of 0.1–2 mm. We furthermore show that our SELENE system is insensitive to gravity and to realistic values of guide waviness. We argue that this guide system can be useful as an optional guide insert when small samples are used in the vicinity of bulky sample environment, e.g. for high-field or high-pressure experiments.

High-speed pellet injection with a two-stage pneumatic gun

International Nuclear Information System (INIS)

Reggiori, A.; Carlevaro, R.; Riva, G.; Daminelli, G.B.; Scaramuzzi, F.; Frattolillo, A.; Martinis, L.; Cardoni, P.; Mori, L.

1988-01-01

The injection of pellets of frozen hydrogen isotopes into fusion plasmas is envisioned as a fueling technique for future fusion reactors. Research is underway to obtain high injection speeds for solid H 2 and D 2 pellets. The optimization of a two-stage light gas gun is being pursued by the Milano group; the search for a convenient method of creating pellets with good mechanical properties and a secure attachment to the cold surface on which they are formed is carried out in Frascati. Velocities >2000 m/s have been obtained, but reproducibility is not yet satisfactory

Two-stage dental implants inserted in a one-stage procedure : a prospective comparative clinical study

NARCIS (Netherlands)

Heijdenrijk, Kees

2002-01-01

The results of this study indicate that dental implants designed for a submerged implantation procedure can be used in a single-stage procedure and may be as predictable as one-stage implants. Although one-stage implant systems and two-stage.

Comparative assessment of single-stage and two-stage anaerobic digestion for the treatment of thin stillage.

Science.gov (United States)

Nasr, Noha; Elbeshbishy, Elsayed; Hafez, Hisham; Nakhla, George; El Naggar, M Hesham

2012-05-01

A comparative evaluation of single-stage and two-stage anaerobic digestion processes for biomethane and biohydrogen production using thin stillage was performed to assess the impact of separating the acidogenic and methanogenic stages on anaerobic digestion. Thin stillage, the main by-product from ethanol production, was characterized by high total chemical oxygen demand (TCOD) of 122 g/L and total volatile fatty acids (TVFAs) of 12 g/L. A maximum methane yield of 0.33 L CH(4)/gCOD(added) (STP) was achieved in the two-stage process while a single-stage process achieved a maximum yield of only 0.26 L CH(4)/gCOD(added) (STP). The separation of acidification stage increased the TVFAs to TCOD ratio from 10% in the raw thin stillage to 54% due to the conversion of carbohydrates into hydrogen and VFAs. Comparison of the two processes based on energy outcome revealed that an increase of 18.5% in the total energy yield was achieved using two-stage anaerobic digestion. Copyright © 2012 Elsevier Ltd. All rights reserved.

Condensate from a two-stage gasifier

DEFF Research Database (Denmark)

Bentzen, Jens Dall; Henriksen, Ulrik Birk; Hindsgaul, Claus

2000-01-01

Condensate, produced when gas from downdraft biomass gasifier is cooled, contains organic compounds that inhibit nitrifiers. Treatment with activated carbon removes most of the organics and makes the condensate far less inhibitory. The condensate from an optimised two-stage gasifier is so clean...... that the organic compounds and the inhibition effect are very low even before treatment with activated carbon. The moderate inhibition effect relates to a high content of ammonia in the condensate. The nitrifiers become tolerant to the condensate after a few weeks of exposure. The level of organic compounds...... and the level of inhibition are so low that condensate from the optimised two-stage gasifier can be led to the public sewer....

Evidence of two-stage melting of Wigner solids

Science.gov (United States)

Knighton, Talbot; Wu, Zhe; Huang, Jian; Serafin, Alessandro; Xia, J. S.; Pfeiffer, L. N.; West, K. W.

2018-02-01

Ultralow carrier concentrations of two-dimensional holes down to p =1 ×109cm-2 are realized. Remarkable insulating states are found below a critical density of pc=4 ×109cm-2 or rs≈40 . Sensitive dc V-I measurement as a function of temperature and electric field reveals a two-stage phase transition supporting the melting of a Wigner solid as a two-stage first-order transition.

Two-stage liquefaction of a Spanish subbituminous coal

Energy Technology Data Exchange (ETDEWEB)

Martinez, M.T.; Fernandez, I.; Benito, A.M.; Cebolla, V.; Miranda, J.L.; Oelert, H.H. (Instituto de Carboquimica, Zaragoza (Spain))

1993-05-01

A Spanish subbituminous coal has been processed in two-stage liquefaction in a non-integrated process. The first-stage coal liquefaction has been carried out in a continuous pilot plant in Germany at Clausthal Technical University at 400[degree]C, 20 MPa hydrogen pressure and anthracene oil as solvent. The second-stage coal liquefaction has been performed in continuous operation in a hydroprocessing unit at the Instituto de Carboquimica at 450[degree]C and 10 MPa hydrogen pressure, with two commercial catalysts: Harshaw HT-400E (Co-Mo/Al[sub 2]O[sub 3]) and HT-500E (Ni-Mo/Al[sub 2]O[sub 3]). The total conversion for the first-stage coal liquefaction was 75.41 wt% (coal d.a.f.), being 3.79 wt% gases, 2.58 wt% primary condensate and 69.04 wt% heavy liquids. The heteroatoms removal for the second-stage liquefaction was 97-99 wt% of S, 85-87 wt% of N and 93-100 wt% of O. The hydroprocessed liquids have about 70% of compounds with boiling point below 350[degree]C, and meet the sulphur and nitrogen specifications for refinery feedstocks. Liquids from two-stage coal liquefaction have been distilled, and the naphtha, kerosene and diesel fractions obtained have been characterized. 39 refs., 3 figs., 8 tabs.

Selenium deficiency occurs in some patients with moderate-to-severe cirrhosis and can be corrected by administration of selenate but not selenomethionine: a randomized controlled trial123

Science.gov (United States)

Burk, Raymond F; Hill, Kristina E; Motley, Amy K; Byrne, Daniel W; Norsworthy, Brooke K

2015-01-01

Background: Selenomethionine, which is the principal dietary form of selenium, is metabolized by the liver to selenide, which is the form of the element required for the synthesis of selenoproteins. The liver synthesizes selenium-rich selenoprotein P (SEPP1) and secretes it into the plasma to supply extrahepatic tissues with selenium. Objectives: We conducted a randomized controlled trial to determine whether cirrhosis is associated with functional selenium deficiency (the lack of selenium for the process of selenoprotein synthesis even though selenium intake is not limited) and, if it is, whether the deficiency is associated with impairment of selenomethionine metabolism. Design: Patients with Child-Pugh (C-P) classes A, B, and C (mild, moderate, and severe, respectively) cirrhosis were supplemented with a placebo or supranutritional amounts of selenium as selenate (200 or 400 μg/d) or as selenomethionine (200 μg/d) for 4 wk. Plasma SEPP1 concentration and glutathione peroxidase (GPX) activity, the latter due largely to the selenoprotein GPX3 secreted by the kidneys, were measured before and after supplementation. Results: GPX activity was increased more by both doses of selenate than by the placebo in C-P class B patients. The activity was not increased more by selenomethionine supplementation than by the placebo in C-P class B patients. Plasma selenium was increased more by 400 μg Se as selenate than by the placebo in C-P class C patients. Within the groups who responded to selenate, there was a considerable variation in responses. Conclusion: These results indicate that severe cirrhosis causes mild functional selenium deficiency in some patients that is associated with impaired metabolism of selenomethionine. This trial was registered at clinicaltrials.gov as NCT00271245. PMID:26468123

One-stage and two-stage penile buccal mucosa urethroplasty

African Journals Online (AJOL)

G. Barbagli

2015-12-02

Dec 2, 2015 ... there also seems to be a trend of decreasing urethritis and an increase of instrumentation and catheter related strictures in these countries as well [4–6]. The repair of penile urethral strictures may require one- or two- stage urethroplasty [7–10]. Certainly, sexual function can be placed at risk by any surgery ...

Two-Stage Variable Sample-Rate Conversion System

Science.gov (United States)

Tkacenko, Andre

2009-01-01

A two-stage variable sample-rate conversion (SRC) system has been pro posed as part of a digital signal-processing system in a digital com munication radio receiver that utilizes a variety of data rates. The proposed system would be used as an interface between (1) an analog- todigital converter used in the front end of the receiver to sample an intermediatefrequency signal at a fixed input rate and (2) digita lly implemented tracking loops in subsequent stages that operate at v arious sample rates that are generally lower than the input sample r ate. This Two-Stage System would be capable of converting from an input sample rate to a desired lower output sample rate that could be var iable and not necessarily a rational fraction of the input rate.

Decomposition and (importance) sampling techniques for multi-stage stochastic linear programs

Energy Technology Data Exchange (ETDEWEB)

Infanger, G.

1993-11-01

The difficulty of solving large-scale multi-stage stochastic linear programs arises from the sheer number of scenarios associated with numerous stochastic parameters. The number of scenarios grows exponentially with the number of stages and problems get easily out of hand even for very moderate numbers of stochastic parameters per stage. Our method combines dual (Benders) decomposition with Monte Carlo sampling techniques. We employ importance sampling to efficiently obtain accurate estimates of both expected future costs and gradients and right-hand sides of cuts. The method enables us to solve practical large-scale problems with many stages and numerous stochastic parameters per stage. We discuss the theory of sharing and adjusting cuts between different scenarios in a stage. We derive probabilistic lower and upper bounds, where we use importance path sampling for the upper bound estimation. Initial numerical results turned out to be promising.

Chiral speciation and determination of selenomethionine enantiomers in selenized yeast by ligand-exchange micellar electrokinetic capillary chromatography after solid phase extraction.

Science.gov (United States)

Duan, Jiankun; He, Man; Hu, Bin

2012-12-14

A new phenylalanine derivative (L-N-(2-hydroxy-propyl)-phenylalanine, L-HP-Phe) was synthesized and its chelate with Cu(II) (Cu(II)-(L-HP-Phe)(2)) was used as the chiral selector for the ligand-exchange (LE) chiral separation of D,L-selenomethionine (SeMet) in selenized yeast samples by micelle electrokinetic capillary chromatography (MEKC). In order to improve the sensitivity of MEKC-UV, two-step preconcentration strategy was employed, off-line solid phase extraction (SPE) and on-line large volume sample stacking (LVSS). D,L-SeMet was first retained on the Cu(II) loaded mesoporous TiO(2), then eluted by 0.1 mL of 5 mol L(-1) ammonia, and finally introduced for MEKC-UV analysis by LVSS injection after evaporation of NH(3). With the enrichment factors of 1400 and 1378, the LODs of 0.44 and 0.60 ng mL(-1) for L-SeMet and D-SeMet was obtained, respectively. The developed method was applied to the analysis of D,L-SeMet in a certified reference material of SELM-1 and a commercial nutrition yeast, and the results showed that most of SeMet in the SELM-1 selenized yeast was l isomer and the recovery for L and D isomers in the spiked commercial nutrition yeast was 96.3% and 103%, respectively. This method is featured with low running cost, high sensitivity and selectivity, and exhibits application potential in chiral analysis of seleno amino acids in real world samples. Copyright © 2012 Elsevier B.V. All rights reserved.

THE EFFECTS OF SODIUM SELENITE AND SELENIZED YEAST SUPPLEMENTATION INTO DIET FOR LAYING HENS ON SELECTED QUALITATIVE PARAMETERS OF TABLE EGGS

Directory of Open Access Journals (Sweden)

HENRIETA ARPÁŠOVÁ

2009-10-01

Full Text Available In this experiment the effects of supplementation of the diet for laying hens with sodium selenite (SS or selenized yeast (SY on whole egg and egg shell quality of layers were studied. The chickens of Shaver Starcross 288 strain were randomly divided at the day of hatching into 4 groups (n=12; in each. The birds were fed from Day 1 of life to 9 months of age with diets differing in amounts and/or forms of selenium. Control group received basal diet (BD containing selenium naturally occurring in feeds (0.1 mg Se/kg of dry matter (DM. First and second experimental group of chickens were fed with a same BD enriched with equivalent dose of Se 0.4 mg/kg DM in form of sodium selenite or selenized yeast, respectively. The feed for third experimental group of birds consisted of BD supplemented with selenized yeast to the final amount of selenium 1.0 mg/kg DM. The egg weight was significantly higher in the groups with SY supplementation only. On the contrary the egg shell ratio was significantly lower in the groups with SY supplementation in both amounts. The width of egg was significantly increased in the groups with selenium supplementation in both forms. The value of egg shell strength was significantly decreased in group with SY in the highest amount 0.9 mg/kg DM The average egg shell thickness was the highest in the experimental group with Se-yeast in amount 0.9 mg/kg DM, however different was not significant compared with control group. The results showed that the most of selected parameters of egg quality appeared to be significantly influenced by selenium supplementation into laying hen’s basal diet.

Use of a two-stage light-gas gun as an injector for electromagnetic railguns

International Nuclear Information System (INIS)

Shahinpoor, M.

1989-01-01

Ablation of wall materials is known to be a major factor limiting the performance of railguns. To minimize this effect, it is desirable too inject projectiles into railgun at velocities greater than the ablation threshold velocity (6-8 km/s for copper rails). Because two-stage light-gas guns are capable of achieving such velocities, a program was initiated to design, build and evaluate the performance of a two-stage light gas gun, utilizing hydrogen gas, for use as an injector to an electromagnetic railgun. This effort is part of a project to develop a hypervelocity electromagnetic launcher (HELEOS) for use in equation-of-state studies. In this paper, the specific design features that enhance compatibility of the injector with the railgun, including a slip-joint between the injector launch tube and the coupling section to the railgun are described. The operational capabilities for using all major projectile velocity measuring techniques, such as in-bore pressure gauges, laser and CW x-ray interrupt techniques, flash x-ray and continuous in-bore velocity measurements using VISAR interferometry are also discussed. Finally an internal ballistics code for optimizing gun performance has been utilized to interpret performance data of the gun

Risk averse optimal operation of a virtual power plant using two stage stochastic programming

International Nuclear Information System (INIS)

Tajeddini, Mohammad Amin; Rahimi-Kian, Ashkan; Soroudi, Alireza

2014-01-01

VPP (Virtual Power Plant) is defined as a cluster of energy conversion/storage units which are centrally operated in order to improve the technical and economic performance. This paper addresses the optimal operation of a VPP considering the risk factors affecting its daily operation profits. The optimal operation is modelled in both day ahead and balancing markets as a two-stage stochastic mixed integer linear programming in order to maximize a GenCo (generation companies) expected profit. Furthermore, the CVaR (Conditional Value at Risk) is used as a risk measure technique in order to control the risk of low profit scenarios. The uncertain parameters, including the PV power output, wind power output and day-ahead market prices are modelled through scenarios. The proposed model is successfully applied to a real case study to show its applicability and the results are presented and thoroughly discussed. - Highlights: • Virtual power plant modelling considering a set of energy generating and conversion units. • Uncertainty modelling using two stage stochastic programming technique. • Risk modelling using conditional value at risk. • Flexible operation of renewable energy resources. • Electricity price uncertainty in day ahead energy markets

Two Automated Techniques for Carotid Lumen Diameter Measurement: Regional versus Boundary Approaches.

Science.gov (United States)

Araki, Tadashi; Kumar, P Krishna; Suri, Harman S; Ikeda, Nobutaka; Gupta, Ajay; Saba, Luca; Rajan, Jeny; Lavra, Francesco; Sharma, Aditya M; Shafique, Shoaib; Nicolaides, Andrew; Laird, John R; Suri, Jasjit S

2016-07-01

The degree of stenosis in the carotid artery can be predicted using automated carotid lumen diameter (LD) measured from B-mode ultrasound images. Systolic velocity-based methods for measurement of LD are subjective. With the advancement of high resolution imaging, image-based methods have started to emerge. However, they require robust image analysis for accurate LD measurement. This paper presents two different algorithms for automated segmentation of the lumen borders in carotid ultrasound images. Both algorithms are modeled as a two stage process. Stage one consists of a global-based model using scale-space framework for the extraction of the region of interest. This stage is common to both algorithms. Stage two is modeled using a local-based strategy that extracts the lumen interfaces. At this stage, the algorithm-1 is modeled as a region-based strategy using a classification framework, whereas the algorithm-2 is modeled as a boundary-based approach that uses the level set framework. Two sets of databases (DB), Japan DB (JDB) (202 patients, 404 images) and Hong Kong DB (HKDB) (50 patients, 300 images) were used in this study. Two trained neuroradiologists performed manual LD tracings. The mean automated LD measured was 6.35 ± 0.95 mm for JDB and 6.20 ± 1.35 mm for HKDB. The precision-of-merit was: 97.4 % and 98.0 % w.r.t to two manual tracings for JDB and 99.7 % and 97.9 % w.r.t to two manual tracings for HKDB. Statistical tests such as ANOVA, Chi-Squared, T-test, and Mann-Whitney test were conducted to show the stability and reliability of the automated techniques.

Anti-kindling induced by two-stage coordinated reset stimulation with weak onset intensity

Directory of Open Access Journals (Sweden)

Magteld eZeitler

2016-05-01

Full Text Available Abnormal neuronal synchrony plays an important role in a number of brain diseases. To specifically counteract abnormal neuronal synchrony by desynchronization, Coordinated Reset (CR stimulation, a spatiotemporally patterned stimulation technique, was designed with computational means. In neuronal networks with spike timing–dependent plasticity CR stimulation causes a decrease of synaptic weights and finally anti-kindling, i.e. unlearning of abnormally strong synaptic connectivity and abnormal neuronal synchrony. Long-lasting desynchronizing aftereffects of CR stimulation have been verified in pre-clinical and clinical proof of concept studies. In general, for different neuromodulation approaches, both invasive and non-invasive, it is desirable to enable effective stimulation at reduced stimulation intensities, thereby avoiding side effects. For the first time, we here present a two-stage CR stimulation protocol, where two qualitatively different types of CR stimulation are delivered one after another, and the first stage comes at a particularly weak stimulation intensity. Numerical simulations show that a two-stage CR stimulation can induce the same degree of anti-kindling as a single-stage CR stimulation with intermediate stimulation intensity. This stimulation approach might be clinically beneficial in patients suffering from brain diseases characterized by abnormal neuronal synchrony where a first treatment stage should be performed at particularly weak stimulation intensities in order to avoid side effects. This might, e.g., be relevant in the context of acoustic CR stimulation in tinnitus patients with hyperacusis or in the case of electrical deep brain CR stimulation with sub-optimally positioned leads or side effects caused by stimulation of the target itself. We discuss how to apply our method in first in man and proof of concept studies.

A Dual-Stage Two-Phase Model of Selective Attention

Science.gov (United States)

Hubner, Ronald; Steinhauser, Marco; Lehle, Carola

2010-01-01

The dual-stage two-phase (DSTP) model is introduced as a formal and general model of selective attention that includes both an early and a late stage of stimulus selection. Whereas at the early stage information is selected by perceptual filters whose selectivity is relatively limited, at the late stage stimuli are selected more efficiently on a…

[Comparison research on two-stage sequencing batch MBR and one-stage MBR].

Science.gov (United States)

Yuan, Xin-Yan; Shen, Heng-Gen; Sun, Lei; Wang, Lin; Li, Shi-Feng

2011-01-01

Aiming at resolving problems in MBR operation, like low nitrogen and phosphorous removal efficiency, severe membrane fouling and etc, comparison research on two-stage sequencing batch MBR (TSBMBR) and one-stage aerobic MBR has been done in this paper. The results indicated that TSBMBR owned advantages of SBR in removing nitrogen and phosphorous, which could make up the deficiency of traditional one-stage aerobic MBR in nitrogen and phosphorous removal. During steady operation period, effluent average NH4(+) -N, TN and TP concentration is 2.83, 12.20, 0.42 mg/L, which could reach domestic scenic environment use. From membrane fouling control point of view, TSBMBR has lower SMP in supernatant, specific trans-membrane flux deduction rate, membrane fouling resistant than one-stage aerobic MBR. The sedimentation and gel layer resistant of TSBMBR was only 6.5% and 33.12% of one-stage aerobic MBR. Besides high efficiency in removing nitrogen and phosphorous, TSBMBR could effectively reduce sedimentation and gel layer pollution on membrane surface. Comparing with one-stage MBR, TSBMBR could operate with higher trans-membrane flux, lower membrane fouling rate and better pollutants removal effects.

Energy demand in Portuguese manufacturing: a two-stage model

International Nuclear Information System (INIS)

Borges, A.M.; Pereira, A.M.

1992-01-01

We use a two-stage model of factor demand to estimate the parameters determining energy demand in Portuguese manufacturing. In the first stage, a capital-labor-energy-materials framework is used to analyze the substitutability between energy as a whole and other factors of production. In the second stage, total energy demand is decomposed into oil, coal and electricity demands. The two stages are fully integrated since the energy composite used in the first stage and its price are obtained from the second stage energy sub-model. The estimates obtained indicate that energy demand in manufacturing responds significantly to price changes. In addition, estimation results suggest that there are important substitution possibilities among energy forms and between energy and other factors of production. The role of price changes in energy-demand forecasting, as well as in energy policy in general, is clearly established. (author)

Selenized milk casein in the diet of BALB/c nude mice reduces growth of intramammary MCF-7 tumors

International Nuclear Information System (INIS)

Warrington, Jenny M; Kim, Julie JM; Stahel, Priska; Cieslar, Scott RL; Moorehead, Roger A; Coomber, Brenda L; Corredig, Milena; Cant, John P

2013-01-01

Dietary selenium has the potential to reduce growth of mammary tumors. Increasing the Se content of cows’ milk proteins is a potentially effective means to increase Se intake in humans. We investigate the effects of selenized milk protein on human mammary tumor progression in immunodeficient BALB/c nude mice. Four isonitrogenous diets with selenium levels of 0.16, 0.51, 0.85 and 1.15 ppm were formulated by mixing low- and high-selenium milk casein isolates with a rodent premix. MCF-7 cells were inoculated into the mammary fat pad of female BALB/c nude mice implanted with slow-release 17 β-estradiol pellets. Mice with palpable tumors were randomly assigned to one of the four diets for 10 weeks, during which time weekly tumor caliper measurements were conducted. Individual growth curves were fit with the Gompertz equation. Apoptotic cells and Bcl-2, Bax, and Cyclin D1 protein levels in tumors were determined. There was a linear decrease in mean tumor volume at 70 days with increasing Se intake (P < 0.05), where final tumor volume decreased 35% between 0.16 and 1.15 ppm Se. There was a linear decrease in mean predicted tumor volume at 56, 63 and 70 days, and the number of tumors with a final volume above 500 mm 3 , with increasing Se intake (P < 0.05). This tumor volume effect was associated with a decrease in the proportion of tumors with a maximum growth rate above 0.03 day -1 . The predicted maximum volume of tumors (V max ) and the number of tumors with a large V max , were not affected by Se-casein. Final tumor mass, Bcl-2, Bax, and Cyclin D1 protein levels in tumors were not significantly affected by Se-casein. There was a significantly higher number of apoptotic cells in high-Se tumors as compared to low-Se tumors. Taken together, these results suggest that turnover of cells in the tumor, but not its nutrient supply, were affected by dairy Se. We have shown that 1.1 ppm dietary Se from selenized casein can effectively reduce tumor progression in an MCF-7

The influence of magnetic field strength in ionization stage on ion transport between two stages of a double stage Hall thruster

International Nuclear Information System (INIS)

Yu Daren; Song Maojiang; Li Hong; Liu Hui; Han Ke

2012-01-01

It is futile for a double stage Hall thruster to design a special ionization stage if the ionized ions cannot enter the acceleration stage. Based on this viewpoint, the ion transport under different magnetic field strengths in the ionization stage is investigated, and the physical mechanisms affecting the ion transport are analyzed in this paper. With a combined experimental and particle-in-cell simulation study, it is found that the ion transport between two stages is chiefly affected by the potential well, the potential barrier, and the potential drop at the bottom of potential well. With the increase of magnetic field strength in the ionization stage, there is larger plasma density caused by larger potential well. Furthermore, the potential barrier near the intermediate electrode declines first and then rises up while the potential drop at the bottom of potential well rises up first and then declines as the magnetic field strength increases in the ionization stage. Consequently, both the ion current entering the acceleration stage and the total ion current ejected from the thruster rise up first and then decline as the magnetic field strength increases in the ionization stage. Therefore, there is an optimal magnetic field strength in the ionization stage to guide the ion transport between two stages.

A Two Stage Solution Procedure for Production Planning System with Advance Demand Information

Science.gov (United States)

Ueno, Nobuyuki; Kadomoto, Kiyotaka; Hasuike, Takashi; Okuhara, Koji

We model for ‘Naiji System’ which is a unique corporation technique between a manufacturer and suppliers in Japan. We propose a two stage solution procedure for a production planning problem with advance demand information, which is called ‘Naiji’. Under demand uncertainty, this model is formulated as a nonlinear stochastic programming problem which minimizes the sum of production cost and inventory holding cost subject to a probabilistic constraint and some linear production constraints. By the convexity and the special structure of correlation matrix in the problem where inventory for different periods is not independent, we propose a solution procedure with two stages which are named Mass Customization Production Planning & Management System (MCPS) and Variable Mesh Neighborhood Search (VMNS) based on meta-heuristics. It is shown that the proposed solution procedure is available to get a near optimal solution efficiently and practical for making a good master production schedule in the suppliers.

Two-stage Catalytic Reduction of NOx with Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Umit S. Ozkan; Erik M. Holmgreen; Matthew M. Yung; Jonathan Halter; Joel Hiltner

2005-12-21

oxidation catalyst. At every stage, catalyst synthesis was guided by the insights gained through detailed characterization of the catalysts using many surface and bulk analysis techniques such as X-ray diffraction, X-ray photoelectron spectroscopy, Temperature-programmed Reduction, Temperature programmed Desorption, and Diffuse Reflectance InfraRed Fourier Transform Spectroscopy as well as steady state reaction experiments. Once active catalysts for each stage had been developed, a physical mixture of the two catalysts was tested for the reduction of NO with methane in lean conditions. These experiments using a mixture of the catalysts produced N2 yields as high as 90%. In the presence of 10% water, the catalyst mixture produced 75% N{sub 2} yield, without any optimization. The dual catalyst system developed has the potential to be implemented in lean-burn natural gas engines for reducing NOx in lean exhaust as well as eliminating CO and unburned hydrocarbons without any fuel penalty or any system modifications. If funding continues, future work will focus on improving the hydrothermal stability of the system to bring the technology closer to application.

Performance Enhancement in L-Band Edfa Through Dual Stage Technique

Directory of Open Access Journals (Sweden)

S. W. Harun and H. Ahmad

2012-10-01

Full Text Available An experiment on gain enhancement in the long wavelength band erbium doped fiber amplifier (L-band EDFA is demonstrated. It uses a dual stage technique with dual forward pumping scheme. Compared to a conventional single stage amplifier, the small signal gain for 1580nm signal can be improved by 5.5dB without paying much noise figure penalty. The corresponding noise figure penalty was 0.3dB due to the insertion loss of the optical isolator. The optimum pump power ratio for the first pump is experimentally determined to be 33%. The maximum gain improvement of 8.3dB was obtained at a signal wavelength of 1568nm while signal and total pump powers were fixed at -30dBm and 92mW, respectively. The employment of dual stage amplifier system seems to play an important role in the development of practical L-band EDFA from the perspective of economical usage of pump power.Key Words:  erbium doped fibre; optical amplifier; L-band EDFA; dual stage EDFA; amplified spontaneous emission

Influence of selenite and selenate supplementation on the chromium uptake and translocation in Allium cepa

International Nuclear Information System (INIS)

Karuna Shanker; Setia, Seema; Srivastava, Shalini; Dass, Sahab; Srivastava, Rohit; Satya Prakash; Srivastava, M.M.

1997-01-01

Pot experiments were conducted on onion plant to study the effects of selenite and selenate treatments (0.5-6.0) μg ml -1 on the uptake and translocation of root absorbed chromium irrigated with 2 and 5 μg ml -1 of chromium in sand and soil. Both the form of selenium (SeO 3 2- , and SeO 4 2- ) were found equally effective in reducing the chromium burden of the plant. No significant difference (p>0.05) in dry matter yields among various selenium treatments exist suggesting no salt injury occurred in the plants under prevailing conditions. (author). 10 refs., 1 tab

Two-Stage Maximum Likelihood Estimation (TSMLE for MT-CDMA Signals in the Indoor Environment

Directory of Open Access Journals (Sweden)

Sesay Abu B

2004-01-01

Full Text Available This paper proposes a two-stage maximum likelihood estimation (TSMLE technique suited for multitone code division multiple access (MT-CDMA system. Here, an analytical framework is presented in the indoor environment for determining the average bit error rate (BER of the system, over Rayleigh and Ricean fading channels. The analytical model is derived for quadrature phase shift keying (QPSK modulation technique by taking into account the number of tones, signal bandwidth (BW, bit rate, and transmission power. Numerical results are presented to validate the analysis, and to justify the approximations made therein. Moreover, these results are shown to agree completely with those obtained by simulation.

Selenization of mixed metal oxides for dense and ZnSe-free Cu{sub 2}ZnSnSe{sub 4} absorber films

Energy Technology Data Exchange (ETDEWEB)

Deng, Yitao; Chen, Guilin; Pan, Bin; Li, JianMin; Jiang, Guoshun; Liu, Weifeng, E-mail: liuwf@ustc.edu.cn; Zhu, Changfei, E-mail: cfzhu@ustc.edu.cn

2014-04-05

Highlights: • ZnSe-free CZTSe films with large grains was prepared from mixed oxides nanopraticles. • Appearance of Zn{sub 2}SnO{sub 4} in mixed oxides precursors leads to the absence of ZnSe secondary phrase. • To obtain pure CZTSe phase, different treating temperature was used. -- Abstract: Cu{sub 2}ZnSnSe{sub 4} (CZTSe) films were prepared by direct selenization of Cu{sub 2}O, SnO{sub 2} and Zn{sub 2}SnO{sub 4} precursors. Oxides precursors were prepared by baking hydroxides precipitation. In order to obtain ZnSe-free CZTSe films, Zn{sub 2}SnO{sub 4} was used to replace separated ZnO and SnO{sub 2} as one of the precursors. Through X-ray diffraction (XRD), scanning electron microscopy (SEM), it was found that CZTSe films, with micron-sized dense grains, were obtained in our work. From Raman spectra, it was also found that the ZnSe secondary phase was absent after the selenization. An energy bandgap about 0.86 eV was obtained in our work, which confirmed the Stannite-CZTSe structure.

Two sampling techniques for game meat

OpenAIRE

van der Merwe, Maretha; Jooste, Piet J.; Hoffman, Louw C.; Calitz, Frikkie J.

2013-01-01

A study was conducted to compare the excision sampling technique used by the export market and the sampling technique preferred by European countries, namely the biotrace cattle and swine test. The measuring unit for the excision sampling was grams (g) and square centimetres (cm2) for the swabbing technique. The two techniques were compared after a pilot test was conducted on spiked approved beef carcasses (n = 12) that statistically proved the two measuring units correlated. The two sampling...

Generation of dense, pulsed beams of refractory metal atoms using two-stage laser ablation

International Nuclear Information System (INIS)

Kadar-Kallen, M.A.; Bonin, K.D.

1994-01-01

We report a technique for generating a dense, pulsed beam of refractory metal atoms using two-stage laser ablation. An atomic beam of uranium was produced with a peak, ground-state number density of 1x10 12 cm -3 at a distance of z=27 cm from the source. This density can be scaled as 1/z 3 to estimate the density at other distances which are also far from the source

Final Report on Two-Stage Fast Spectrum Fuel Cycle Options

International Nuclear Information System (INIS)

Yang, Won Sik; Lin, C. S.; Hader, J. S.; Park, T. K.; Deng, P.; Yang, G.; Jung, Y. S.; Kim, T. K.; Stauff, N. E.

2016-01-01

This report presents the performance characteristics of two ''two-stage'' fast spectrum fuel cycle options proposed to enhance uranium resource utilization and to reduce nuclear waste generation. One is a two-stage fast spectrum fuel cycle option of continuous recycle of plutonium (Pu) in a fast reactor (FR) and subsequent burning of minor actinides (MAs) in an accelerator-driven system (ADS). The first stage is a sodium-cooled FR fuel cycle starting with low-enriched uranium (LEU) fuel; at the equilibrium cycle, the FR is operated using the recovered Pu and natural uranium without supporting LEU. Pu and uranium (U) are co-extracted from the discharged fuel and recycled in the first stage, and the recovered MAs are sent to the second stage. The second stage is a sodium-cooled ADS in which MAs are burned in an inert matrix fuel form. The discharged fuel of ADS is reprocessed, and all the recovered heavy metals (HMs) are recycled into the ADS. The other is a two-stage FR/ADS fuel cycle option with MA targets loaded in the FR. The recovered MAs are not directly sent to ADS, but partially incinerated in the FR in order to reduce the amount of MAs to be sent to the ADS. This is a heterogeneous recycling option of transuranic (TRU) elements

Two-stage electrolysis to enrich tritium in environmental water

International Nuclear Information System (INIS)

Shima, Nagayoshi; Muranaka, Takeshi

2007-01-01

We present a two-stage electrolyzing procedure to enrich tritium in environmental waters. Tritium is first enriched rapidly through a commercially-available electrolyser with a large 50A current, and then through a newly-designed electrolyser that avoids the memory effect, with a 6A current. Tritium recovery factor obtained by such a two-stage electrolysis was greater than that obtained when using the commercially-available device solely. Water samples collected in 2006 in lakes and along the Pacific coast of Aomori prefecture, Japan, were electrolyzed using the two-stage method. Tritium concentrations in these samples ranged from 0.2 to 0.9 Bq/L and were half or less, that in samples collected at the same sites in 1992. (author)

Two-stage nonrecursive filter/decimator

International Nuclear Information System (INIS)

Yoder, J.R.; Richard, B.D.

1980-08-01

A two-stage digital filter/decimator has been designed and implemented to reduce the sampling rate associated with the long-term computer storage of certain digital waveforms. This report describes the design selection and implementation process and serves as documentation for the system actually installed. A filter design with finite-impulse response (nonrecursive) was chosen for implementation via direct convolution. A newly-developed system-test statistic validates the system under different computer-operating environments

On A Two-Stage Supply Chain Model In The Manufacturing Industry ...

African Journals Online (AJOL)

We model a two-stage supply chain where the upstream stage (stage 2) always meet demand from the downstream stage (stage 1).Demand is stochastic hence shortages will occasionally occur at stage 2. Stage 2 must fill these shortages by expediting using overtime production and/or backordering. We derive optimal ...

Treatment of corn ethanol distillery wastewater using two-stage anaerobic digestion.

Science.gov (United States)

Ráduly, B; Gyenge, L; Szilveszter, Sz; Kedves, A; Crognale, S

In this study the mesophilic two-stage anaerobic digestion (AD) of corn bioethanol distillery wastewater is investigated in laboratory-scale reactors. Two-stage AD technology separates the different sub-processes of the AD in two distinct reactors, enabling the use of optimal conditions for the different microbial consortia involved in the different process phases, and thus allowing for higher applicable organic loading rates (OLRs), shorter hydraulic retention times (HRTs) and better conversion rates of the organic matter, as well as higher methane content of the produced biogas. In our experiments the reactors have been operated in semi-continuous phase-separated mode. A specific methane production of 1,092 mL/(L·d) has been reached at an OLR of 6.5 g TCOD/(L·d) (TCOD: total chemical oxygen demand) and a total HRT of 21 days (5.7 days in the first-stage, and 15.3 days in the second-stage reactor). Nonetheless the methane concentration in the second-stage reactor was very high (78.9%); the two-stage AD outperformed the reference single-stage AD (conducted at the same reactor loading rate and retention time) by only a small margin in terms of volumetric methane production rate. This makes questionable whether the higher methane content of the biogas counterbalances the added complexity of the two-stage digestion.

Rapid Two-stage Versus One-stage Surgical Repair of Interrupted Aortic Arch with Ventricular Septal Defect in Neonates

Directory of Open Access Journals (Sweden)

Meng-Lin Lee

2008-11-01

Conclusion: The outcome of rapid two-stage repair is comparable to that of one-stage repair. Rapid two-stage repair has the advantages of significantly shorter cardiopulmonary bypass duration and AXC time, and avoids deep hypothermic circulatory arrest. LVOTO remains an unresolved issue, and postoperative aortic arch restenosis can be dilated effectively by percutaneous balloon angioplasty.

Broadband and polarization reflectors in the lookdown, Selene vomer.

Science.gov (United States)

Zhao, Shulei; Brady, Parrish Clawson; Gao, Meng; Etheredge, Robert Ian; Kattawar, George W; Cummings, Molly E

2015-03-06

Predator evasion in the open ocean is difficult because there are no objects to hide behind. The silvery surface of fish plays an important role in open water camouflage. Various models have been proposed to account for the broadband reflectance by the fish skin that involve one-dimensional variations in the arrangement of guanine crystal reflectors, yet the three-dimensional organization of these guanine platelets have not been well characterized. Here, we report the three-dimensional organization and the optical properties of integumentary guanine platelets in a silvery marine fish, the lookdown (Selene vomer). Our structural analysis and computational modelling show that stacks of guanine platelets with random yaw angles in the fish skin produce broadband reflectance via colour mixing. Optical axes of the guanine platelets and the collagen layer are aligned closely and provide bulk birefringence properties that influence the polarization reflectance by the skin. These data demonstrate how the lookdown preserves or alters polarization states at different incident polarization angles. These optical properties resulted from the organization of these guanine platelets and the collagen layer may have implications for open ocean camouflage in varying light fields. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Final Report on Two-Stage Fast Spectrum Fuel Cycle Options

Energy Technology Data Exchange (ETDEWEB)

Yang, Won Sik [Purdue Univ., West Lafayette, IN (United States); Lin, C. S. [Purdue Univ., West Lafayette, IN (United States); Hader, J. S. [Purdue Univ., West Lafayette, IN (United States); Park, T. K. [Purdue Univ., West Lafayette, IN (United States); Deng, P. [Purdue Univ., West Lafayette, IN (United States); Yang, G. [Purdue Univ., West Lafayette, IN (United States); Jung, Y. S. [Purdue Univ., West Lafayette, IN (United States); Kim, T. K. [Argonne National Lab. (ANL), Argonne, IL (United States); Stauff, N. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-01-30

This report presents the performance characteristics of two “two-stage” fast spectrum fuel cycle options proposed to enhance uranium resource utilization and to reduce nuclear waste generation. One is a two-stage fast spectrum fuel cycle option of continuous recycle of plutonium (Pu) in a fast reactor (FR) and subsequent burning of minor actinides (MAs) in an accelerator-driven system (ADS). The first stage is a sodium-cooled FR fuel cycle starting with low-enriched uranium (LEU) fuel; at the equilibrium cycle, the FR is operated using the recovered Pu and natural uranium without supporting LEU. Pu and uranium (U) are co-extracted from the discharged fuel and recycled in the first stage, and the recovered MAs are sent to the second stage. The second stage is a sodium-cooled ADS in which MAs are burned in an inert matrix fuel form. The discharged fuel of ADS is reprocessed, and all the recovered heavy metals (HMs) are recycled into the ADS. The other is a two-stage FR/ADS fuel cycle option with MA targets loaded in the FR. The recovered MAs are not directly sent to ADS, but partially incinerated in the FR in order to reduce the amount of MAs to be sent to the ADS. This is a heterogeneous recycling option of transuranic (TRU) elements

Toxicity of inorganic contaminants, individually and in environmental mixtures, to three endangered fishes (Colorado squawfish, bonytail, and razorback sucker)

Science.gov (United States)

Buhl, Kevin J.; Hamilton, S.J.

1996-01-01

Two life stages of three federally-listed endangered fishes, Colorado squawfish (Ptychocheilus lucius), bonytail (Gila elegans), and razorback sucker (Xyrauchen texanus) were exposed to copper, selenate, selenite, and zinc individually, and to mixtures of nine inorganics in a reconstituted water that simulated the water quality of the middle Green River, Utah. The mixtures simulated environmental ratios of arsenate, boron, copper, molybdenum, selenate, selenite, uranium, vanadium, and zinc in two tributaries, Ashley Creek and Stewart Lake outlet, of the middle Green River. The rank order of toxicity of the individual inorganics, from most to least toxic, was: copper > zinc > selenite > selenate. Colorado squawfish larvae were more sensitive to all four inorganics and the two mixtures than the juveniles, whereas there was no consistent response between the two life stages for the other two species. There was no consistent difference in sensitivity to the inorganics among the three endangered fishes. Both mixtures exhibited either additive or greater than additive toxicity to these fishes. The primary toxic components in the mixtures, based on toxic units, were copper and zinc. Acute toxicity values were compared to measured environmental concentrations in the two tributaries to derive margins of uncertainty. Margins of uncertainty were low for both mixtures (9–22 for the Stewart Lake outlet mixture, and 12–32 for the Ashley Creek mixture), indicating that mixtures of inorganics derived from irrigation activities may pose a hazard to endangered fishes in the Green River.

Runway Operations Planning: A Two-Stage Heuristic Algorithm

Science.gov (United States)

Anagnostakis, Ioannis; Clarke, John-Paul

2003-01-01

The airport runway is a scarce resource that must be shared by different runway operations (arrivals, departures and runway crossings). Given the possible sequences of runway events, careful Runway Operations Planning (ROP) is required if runway utilization is to be maximized. From the perspective of departures, ROP solutions are aircraft departure schedules developed by optimally allocating runway time for departures given the time required for arrivals and crossings. In addition to the obvious objective of maximizing throughput, other objectives, such as guaranteeing fairness and minimizing environmental impact, can also be incorporated into the ROP solution subject to constraints introduced by Air Traffic Control (ATC) procedures. This paper introduces a two stage heuristic algorithm for solving the Runway Operations Planning (ROP) problem. In the first stage, sequences of departure class slots and runway crossings slots are generated and ranked based on departure runway throughput under stochastic conditions. In the second stage, the departure class slots are populated with specific flights from the pool of available aircraft, by solving an integer program with a Branch & Bound algorithm implementation. Preliminary results from this implementation of the two-stage algorithm on real-world traffic data are presented.

Behaviour of selenate in soils: experimental approach and modeling of hysteresis of sorption/desorption

International Nuclear Information System (INIS)

Loffredo, N.

2010-01-01

In the context of future storage of nuclear material in deep geological layers, the transfer of selenium-79 from groundwater to biosphere through irrigation is one of the scenarios considered by the ANDRA (National Agency for Radioactive Waste Management). So, the soil would act as an interface between the geosphere and biosphere. Actually the model adopted to evaluate the element mobility in soil is based on a simple representation of its distribution between the quantity adsorbed on the soil and the amount remaining in the solution (KD model). Such distribution is considered as instantaneous, reversible and linear with the concentration of contamination. This model has some inadequacies with respect to selenium because this latter can be present in different redox states that control its mobility and whose transformation kinetics among states are poorly known (Se(-II), Se(0), Se(IV) and Se(VI)). In order to improve predictions on the mobility of selenium in soil, selenate (Se(VI)) - which is the most mobile form - has been used to study its interactions with respect to two different soils (soil B and soil R). A kinetic model, alternative to the K d model, has been developed to describe the evolution of stocks of Se(VI) in solution. This model considers that a fraction of selenium is associated with soil in a reversibly way (potentially mobile) and a portion of it is stabilized in soil (pseudo-irreversibly fixed). This model integrates on one hand, in the soil, kinetics of biotic and abiotic stabilization and on the other hand, in solution, a reduction kinetic. With the goal of acquiring the parameters of the models, various experiments using dialysis bags have been effectuated, both in batch and with open-flow reactors. The parameter acquisition has allowed kinetic and K d models to be compared in different realistic scenarios of contamination (chronic or sequential) of a surface soil with 79 Se(VI). In addition, the sorption mechanisms of Se(VI) have been

Two-stage residual inclusion estimation: addressing endogeneity in health econometric modeling.

Science.gov (United States)

Terza, Joseph V; Basu, Anirban; Rathouz, Paul J

2008-05-01

The paper focuses on two estimation methods that have been widely used to address endogeneity in empirical research in health economics and health services research-two-stage predictor substitution (2SPS) and two-stage residual inclusion (2SRI). 2SPS is the rote extension (to nonlinear models) of the popular linear two-stage least squares estimator. The 2SRI estimator is similar except that in the second-stage regression, the endogenous variables are not replaced by first-stage predictors. Instead, first-stage residuals are included as additional regressors. In a generic parametric framework, we show that 2SRI is consistent and 2SPS is not. Results from a simulation study and an illustrative example also recommend against 2SPS and favor 2SRI. Our findings are important given that there are many prominent examples of the application of inconsistent 2SPS in the recent literature. This study can be used as a guide by future researchers in health economics who are confronted with endogeneity in their empirical work.

Maximally efficient two-stage screening: Determining intellectual disability in Taiwanese military conscripts.

Science.gov (United States)

Chien, Chia-Chang; Huang, Shu-Fen; Lung, For-Wey

2009-01-27

The purpose of this study was to apply a two-stage screening method for the large-scale intelligence screening of military conscripts. We collected 99 conscripted soldiers whose educational levels were senior high school level or lower to be the participants. Every participant was required to take the Wisconsin Card Sorting Test (WCST) and the Wechsler Adult Intelligence Scale-Revised (WAIS-R) assessments. Logistic regression analysis showed the conceptual level responses (CLR) index of the WCST was the most significant index for determining intellectual disability (ID; FIQ ≤ 84). We used the receiver operating characteristic curve to determine the optimum cut-off point of CLR. The optimum one cut-off point of CLR was 66; the two cut-off points were 49 and 66. Comparing the two-stage window screening with the two-stage positive screening, the area under the curve and the positive predictive value increased. Moreover, the cost of the two-stage window screening decreased by 59%. The two-stage window screening is more accurate and economical than the two-stage positive screening. Our results provide an example for the use of two-stage screening and the possibility of the WCST to replace WAIS-R in large-scale screenings for ID in the future.

The Two-Word Stage: Motivated by Linguistic or Cognitive Constraints?

Science.gov (United States)

Berk, Stephanie; Lillo-Martin, Diane

2012-01-01

Child development researchers often discuss a "two-word" stage during language acquisition. However, there is still debate over whether the existence of this stage reflects primarily cognitive or linguistic constraints. Analyses of longitudinal data from two Deaf children, Mei and Cal, not exposed to an accessible first language (American Sign…

A two-stage heating scheme for heat assisted magnetic recording

Science.gov (United States)

Xiong, Shaomin; Kim, Jeongmin; Wang, Yuan; Zhang, Xiang; Bogy, David

2014-05-01

Heat Assisted Magnetic Recording (HAMR) has been proposed to extend the storage areal density beyond 1 Tb/in.2 for the next generation magnetic storage. A near field transducer (NFT) is widely used in HAMR systems to locally heat the magnetic disk during the writing process. However, much of the laser power is absorbed around the NFT, which causes overheating of the NFT and reduces its reliability. In this work, a two-stage heating scheme is proposed to reduce the thermal load by separating the NFT heating process into two individual heating stages from an optical waveguide and a NFT, respectively. As the first stage, the optical waveguide is placed in front of the NFT and delivers part of laser energy directly onto the disk surface to heat it up to a peak temperature somewhat lower than the Curie temperature of the magnetic material. Then, the NFT works as the second heating stage to heat a smaller area inside the waveguide heated area further to reach the Curie point. The energy applied to the NFT in the second heating stage is reduced compared with a typical single stage NFT heating system. With this reduced thermal load to the NFT by the two-stage heating scheme, the lifetime of the NFT can be extended orders longer under the cyclic load condition.

Efficacy of single-stage and two-stage Fowler–Stephens laparoscopic orchidopexy in the treatment of intraabdominal high testis

Directory of Open Access Journals (Sweden)

Chang-Yuan Wang

2017-11-01

Conclusion: In the case of testis with good collateral circulation, single-stage F-S laparoscopic orchidopexy had the same safety and efficacy as the two-stage F-S procedure. Surgical options should be based on comprehensive consideration of intraoperative testicular location, testicular ischemia test, and collateral circumstances surrounding the testes. Under the appropriate conditions, we propose single-stage F-S laparoscopic orchidopexy be preferred. It may be appropriate to avoid unnecessary application of the two-stage procedure that has a higher cost and causes more pain for patients.

Abiotic pyrite reactivity versus nitrate, selenate and selenite using chemical and electrochemical methods

International Nuclear Information System (INIS)

Ignatiadis, I.; Betelu, S.; Gaucher, E.; Tournassat, C.; Chainet, F.

2010-01-01

Document available in extended abstract form only. This work is part of ReCosy European project (www.recosy.eu), whose main objectives are the sound understanding of redox phenomena controlling the long-term release/retention of radionuclides in nuclear waste disposal and providing tools to apply the results to performance assessment/safety case. Redox is one of the main factor affecting speciation and mobility of redox-sensitive radionuclides. Thus, it is of a great importance to investigate the redox reactivity of the host radioactive waste formations, particularly when exposed to redox perturbations. Callovo-Oxfordian formation (COx), a clay rock known as an anoxic and reducing system, was selected in France as the most suitable location to store nuclear waste. Iron (II) sulfide, mostly constituted of pyrite (FeS 2 ), iron (II) carbonate, iron(II) bearing clays and organic matter are considered to account almost entirely for the total reducing capacity of the rock. We report here the redox reactivity of pyrite upon exposure to nitrate (N(V)), selenate (Se(VI)) and selenite (Se(IV)) that possibly occur in the nuclear storage. Both, chemical and electrochemical kinetic approaches were simultaneously conducted such as to (i) determine the kinetics parameters of the reactions and (ii) understand the kinetic mechanisms. In order to reach similar conditions that are encountered in the storage system, all experiments were realised in NaCl 0.1 M, near neutral pH solutions, and an abiotic glove box (O 2 less than 10 -8 M). Chemical approach has consisted to set in contact pyrite in grains with solutions containing respectively nitrate, selenate and selenite. Reactants and products chemical analyses, conducted at different contact times, allowed us to assess the kinetics of oxidant reduction. Electrochemical approach has consisted in the continuous or semi-continuous analysis of large surface pyrite electrodes immersed in solutions with or without oxidant (nitrate

Two-thumb technique is superior to two-finger technique during lone rescuer infant manikin CPR.

Science.gov (United States)

Udassi, Sharda; Udassi, Jai P; Lamb, Melissa A; Theriaque, Douglas W; Shuster, Jonathan J; Zaritsky, Arno L; Haque, Ikram U

2010-06-01

Infant CPR guidelines recommend two-finger chest compression with a lone rescuer and two-thumb with two rescuers. Two-thumb provides better chest compression but is perceived to be associated with increased ventilation hands-off time. We hypothesized that lone rescuer two-thumb CPR is associated with increased ventilation cycle time, decreased ventilation quality and fewer chest compressions compared to two-finger CPR in an infant manikin model. Crossover observational study randomizing 34 healthcare providers to perform 2 min CPR at a compression rate of 100 min(-1) using a 30:2 compression:ventilation ratio comparing two-thumb vs. two-finger techniques. A Laerdal Baby ALS Trainer manikin was modified to digitally record compression rate, compression depth and compression pressure and ventilation cycle time (two mouth-to-mouth breaths). Manikin chest rise with breaths was video recorded and later reviewed by two blinded CPR instructors for percent effective breaths. Data (mean+/-SD) were analyzed using a two-tailed paired t-test. Significance was defined qualitatively as pCPR, but there was no significant difference in percent effective breaths delivered between the two techniques. Two-thumb CPR had 4 fewer delivered compressions per minute, which may be offset by far more effective compression depth and compression pressure compared to two-finger technique. Copyright 2010 Elsevier Ireland Ltd. All rights reserved.

Using external and internal locking plates in a two-stage protocol for treatment of segmental tibial fractures.

Science.gov (United States)

Ma, Ching-Hou; Tu, Yuan-Kun; Yeh, Jih-Hsi; Yang, Shih-Chieh; Wu, Chin-Hsien

2011-09-01

The tibial segmental fractures usually follow high-energy trauma and are often associated with many complications. We designed a two-stage protocol for these complex injuries. The aim of this study was to assess the outcome of tibial segmental fractures treated according to this protocol. A prospective series of 25 consecutive segmental tibial fractures were treated using a two-stage procedure. In the first stage, a low-profile locking plate was applied as an external fixator to temporarily immobilize the fractures after anatomic reduction had been achieved followed by soft-tissue reconstruction. The second stage involved definitive internal fixation with a locking plate using a minimally invasive percutaneous plate osteosynthesis technique. The median follow-up was 32 months (range, 20-44 months). All fractures achieved union. The median time for the proximal fracture union was 23 weeks (range, 12-30 weeks) and that for distal fracture union was 27 weeks (range, 12-46 weeks; p = 0.08). Functional results were excellent in 21 patients and good in 4 patients. There were three cases of delayed union of distal fracture. Valgus malunion >5 degrees occurred in two patients, and length discrepancy >1 cm was observed in two patients. Pin tract infection occurred in three patients. Use of the two-stage procedure for treatment of segmental tibial fractures is recommended. Surgeons can achieve good reduction with stable temporary fixation, soft-tissue reconstruction, ease of subsequent definitive fixation, and high union rates. Our patients obtained excellent knee and ankle joint motion, good functional outcomes, and a comfortable clinical course.

Comparative evaluation of efficacy and soft tissue wound healing using diode laser (810 nm versus conventional scalpel technique for second-stage implant surgery

Directory of Open Access Journals (Sweden)

Manvir Kaur

2018-01-01

Full Text Available Background: This study was aimed to compare the efficacy and soft tissue wound healing using diode lasers (810 nm versus conventional scalpel approach as uncovering technique during the second-stage surgery in implants. This was a prospective, randomized study which was conducted on 20 subjects in which the implants were already placed using a two-stage technique. Implant sites were examined and the patients were randomly divided into two groups. Materials and Methods: Patients were randomly divided into two groups, i.e., Group A and Group B. In Group A, implants were uncovered as a part of Stage II surgery with conventional scalpel technique, and in Group B, implants were uncovered using 810 nm diode laser. Clinical parameters such as need and amount of local anesthesia, duration of surgery, intraoperative bleeding, pain index, wound healing index (HI, and time for impression taking were recorded at various intervals. Results: Statistical differences for clinical parameters were seen between Group A and Group B showing uncovery of implant with laser more effective, and for time of impression taking, difference was statistically significant showing that impressions were taken early in case of Group A because of better healing which was recorded with help of HI, but the difference in time of healing between Group A and Group B was not statistically significant. Conclusion: The use of a diode laser (810 nm in the second-stage implant surgery can minimize surgical trauma, reduce the amount of anesthesia, improve visibility during surgery due to the absence of bleeding, and eliminate postoperative discomfort.

Two-Stage Regularized Linear Discriminant Analysis for 2-D Data.

Science.gov (United States)

Zhao, Jianhua; Shi, Lei; Zhu, Ji

2015-08-01

Fisher linear discriminant analysis (LDA) involves within-class and between-class covariance matrices. For 2-D data such as images, regularized LDA (RLDA) can improve LDA due to the regularized eigenvalues of the estimated within-class matrix. However, it fails to consider the eigenvectors and the estimated between-class matrix. To improve these two matrices simultaneously, we propose in this paper a new two-stage method for 2-D data, namely a bidirectional LDA (BLDA) in the first stage and the RLDA in the second stage, where both BLDA and RLDA are based on the Fisher criterion that tackles correlation. BLDA performs the LDA under special separable covariance constraints that incorporate the row and column correlations inherent in 2-D data. The main novelty is that we propose a simple but effective statistical test to determine the subspace dimensionality in the first stage. As a result, the first stage reduces the dimensionality substantially while keeping the significant discriminant information in the data. This enables the second stage to perform RLDA in a much lower dimensional subspace, and thus improves the two estimated matrices simultaneously. Experiments on a number of 2-D synthetic and real-world data sets show that BLDA+RLDA outperforms several closely related competitors.

Two-stage precipitation of plutonium trifluoride

International Nuclear Information System (INIS)

Luerkens, D.W.

1984-04-01

Plutonium trifluoride was precipitated using a two-stage precipitation system. A series of precipitation experiments identified the significant process variables affecting precipitate characteristics. A mathematical precipitation model was developed which was based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter that can be used to control particle characteristics

A New Concept of Two-Stage Multi-Element Resonant-/Cyclo-Converter for Two-Phase IM/SM Motor

Directory of Open Access Journals (Sweden)

Mahmud Ali Rzig Abdalmula

2013-01-01

Full Text Available The paper deals with a new concept of power electronic two-phase system with two-stage DC/AC/AC converter and two-phase IM/PMSM motor. The proposed system consisting of two-stage converter comprises: input resonant boost converter with AC output, two-phase half-bridge cyclo-converter commutated by HF AC input voltage, and induction or synchronous motor. Such a system with AC interlink, as a whole unit, has better properties as a 3-phase reference VSI inverter: higher efficiency due to soft switching of both converter stages, higher switching frequency, smaller dimensions and weight with lesser number of power semiconductor switches and better price. In comparison with currently used conventional system configurations the proposed system features a good efficiency of electronic converters and also has a good torque overloading of two-phase AC induction or synchronous motors. Design of two-stage multi-element resonant converter and results of simulation experiments are presented in the paper.

Two-Stage Fuzzy Portfolio Selection Problem with Transaction Costs

OpenAIRE

Chen, Yanju; Wang, Ye

2015-01-01

This paper studies a two-period portfolio selection problem. The problem is formulated as a two-stage fuzzy portfolio selection model with transaction costs, in which the future returns of risky security are characterized by possibility distributions. The objective of the proposed model is to achieve the maximum utility in terms of the expected value and variance of the final wealth. Given the first-stage decision vector and a realization of fuzzy return, the optimal value expression of the s...

On the robustness of two-stage estimators

KAUST Repository

Zhelonkin, Mikhail; Genton, Marc G.; Ronchetti, Elvezio

2012-01-01

The aim of this note is to provide a general framework for the analysis of the robustness properties of a broad class of two-stage models. We derive the influence function, the change-of-variance function, and the asymptotic variance of a general

Effluent composition prediction of a two-stage anaerobic digestion process: machine learning and stoichiometry techniques.

Science.gov (United States)

Alejo, Luz; Atkinson, John; Guzmán-Fierro, Víctor; Roeckel, Marlene

2018-05-16

Computational self-adapting methods (Support Vector Machines, SVM) are compared with an analytical method in effluent composition prediction of a two-stage anaerobic digestion (AD) process. Experimental data for the AD of poultry manure were used. The analytical method considers the protein as the only source of ammonia production in AD after degradation. Total ammonia nitrogen (TAN), total solids (TS), chemical oxygen demand (COD), and total volatile solids (TVS) were measured in the influent and effluent of the process. The TAN concentration in the effluent was predicted, this being the most inhibiting and polluting compound in AD. Despite the limited data available, the SVM-based model outperformed the analytical method for the TAN prediction, achieving a relative average error of 15.2% against 43% for the analytical method. Moreover, SVM showed higher prediction accuracy in comparison with Artificial Neural Networks. This result reveals the future promise of SVM for prediction in non-linear and dynamic AD processes. Graphical abstract ᅟ.

EVALUATION OF A TWO-STAGE PASSIVE TREATMENT APPROACH FOR MINING INFLUENCE WATERS

Science.gov (United States)

A two-stage passive treatment approach was assessed at bench-scale using two Colorado Mining Influenced Waters (MIWs). The first-stage was a limestone drain with the purpose of removing iron and aluminum and mitigating the potential effects of mineral acidity. The second stage w...

Transport fuels from two-stage coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Benito, A.; Cebolla, V.; Fernandez, I.; Martinez, M.T.; Miranda, J.L.; Oelert, H.; Prado, J.G. (Instituto de Carboquimica CSIC, Zaragoza (Spain))

1994-03-01

Four Spanish lignites and their vitrinite concentrates were evaluated for coal liquefaction. Correlationships between the content of vitrinite and conversion in direct liquefaction were observed for the lignites but not for the vitrinite concentrates. The most reactive of the four coals was processed in two-stage liquefaction at a higher scale. First-stage coal liquefaction was carried out in a continuous unit at Clausthal University at a temperature of 400[degree]C at 20 MPa hydrogen pressure and with anthracene oil as a solvent. The coal conversion obtained was 75.41% being 3.79% gases, 2.58% primary condensate and 69.04% heavy liquids. A hydroprocessing unit was built at the Instituto de Carboquimica for the second-stage coal liquefaction. Whole and deasphalted liquids from the first-stage liquefaction were processed at 450[degree]C and 10 MPa hydrogen pressure, with two commercial catalysts: Harshaw HT-400E (Co-Mo/Al[sub 2]O[sub 3]) and HT-500E (Ni-Mo/Al[sub 2]O[sub 3]). The effects of liquid hourly space velocity (LHSV), temperature, gas/liquid ratio and catalyst on the heteroatom liquids, and levels of 5 ppm of nitrogen and 52 ppm of sulphur were reached at 450[degree]C, 10 MPa hydrogen pressure, 0.08 kg H[sub 2]/kg feedstock and with Harshaw HT-500E catalyst. The liquids obtained were hydroprocessed again at 420[degree]C, 10 MPa hydrogen pressure and 0.06 kg H[sub 2]/kg feedstock to hydrogenate the aromatic structures. In these conditions, the aromaticity was reduced considerably, and 39% of naphthas and 35% of kerosene fractions were obtained. 18 refs., 4 figs., 4 tabs.

Maximally efficient two-stage screening: Determining intellectual disability in Taiwanese military conscripts

Directory of Open Access Journals (Sweden)

Chia-Chang Chien

2009-01-01

Full Text Available Chia-Chang Chien1, Shu-Fen Huang1,2,3,4, For-Wey Lung1,2,3,41Department of Psychiatry, Kaohsiung Armed Forces General Hospital, Kaohsiung, Taiwan; 2Graduate Institute of Behavioral Sciences, Kaohsiung Medical University, Kaohsiung, Taiwan; 3Department of Psychiatry, National Defense Medical Center, Taipei, Taiwan; 4Calo Psychiatric Center, Pingtung County, TaiwanObjective: The purpose of this study was to apply a two-stage screening method for the large-scale intelligence screening of military conscripts.Methods: We collected 99 conscripted soldiers whose educational levels were senior high school level or lower to be the participants. Every participant was required to take the Wisconsin Card Sorting Test (WCST and the Wechsler Adult Intelligence Scale-Revised (WAIS-R assessments.Results: Logistic regression analysis showed the conceptual level responses (CLR index of the WCST was the most significant index for determining intellectual disability (ID; FIQ ≤ 84. We used the receiver operating characteristic curve to determine the optimum cut-off point of CLR. The optimum one cut-off point of CLR was 66; the two cut-off points were 49 and 66. Comparing the two-stage window screening with the two-stage positive screening, the area under the curve and the positive predictive value increased. Moreover, the cost of the two-stage window screening decreased by 59%.Conclusion: The two-stage window screening is more accurate and economical than the two-stage positive screening. Our results provide an example for the use of two-stage screening and the possibility of the WCST to replace WAIS-R in large-scale screenings for ID in the future.Keywords: intellectual disability, intelligence screening, two-stage positive screening, Wisconsin Card Sorting Test, Wechsler Adult Intelligence Scale-Revised

Two-stage model of development of heterogeneous uranium-lead systems in zircon

International Nuclear Information System (INIS)

Mel'nikov, N.N.; Zevchenkov, O.A.

1985-01-01

Behaviour of isotope systems of multiphase zircons at their two-stage distortion is considered. The results of calculations testify to the fact that linear correlations on the diagram with concordance can be explained including two-stage discovery of U-Pb systems of cogenetic zircons if zircon is considered physically heterogeneous and losing in its different part different ratios of accumulated radiogenic lead. ''Metamorphism ages'' obtained by these two-stage opening zircons are intermediate, and they not have geochronological significance while ''crystallization ages'' remain rather close to real ones. Two-stage opening zircons in some cases can be diagnosed by discordance of their crystal component

A two-stage rule-constrained seedless region growing approach for mandibular body segmentation in MRI.

Science.gov (United States)

Ji, Dong Xu; Foong, Kelvin Weng Chiong; Ong, Sim Heng

2013-09-01

Extraction of the mandible from 3D volumetric images is frequently required for surgical planning and evaluation. Image segmentation from MRI is more complex than CT due to lower bony signal-to-noise. An automated method to extract the human mandible body shape from magnetic resonance (MR) images of the head was developed and tested. Anonymous MR images data sets of the head from 12 subjects were subjected to a two-stage rule-constrained region growing approach to derive the shape of the body of the human mandible. An initial thresholding technique was applied followed by a 3D seedless region growing algorithm to detect a large portion of the trabecular bone (TB) regions of the mandible. This stage is followed with a rule-constrained 2D segmentation of each MR axial slice to merge the remaining portions of the TB regions with lower intensity levels. The two-stage approach was replicated to detect the cortical bone (CB) regions of the mandibular body. The TB and CB regions detected from the preceding steps were merged and subjected to a series of morphological processes for completion of the mandibular body region definition. Comparisons of the accuracy of segmentation between the two-stage approach, conventional region growing method, 3D level set method, and manual segmentation were made with Jaccard index, Dice index, and mean surface distance (MSD). The mean accuracy of the proposed method is [Formula: see text] for Jaccard index, [Formula: see text] for Dice index, and [Formula: see text] mm for MSD. The mean accuracy of CRG is [Formula: see text] for Jaccard index, [Formula: see text] for Dice index, and [Formula: see text] mm for MSD. The mean accuracy of the 3D level set method is [Formula: see text] for Jaccard index, [Formula: see text] for Dice index, and [Formula: see text] mm for MSD. The proposed method shows improvement in accuracy over CRG and 3D level set. Accurate segmentation of the body of the human mandible from MR images is achieved with the

Acceleration of small, light projectiles (including hydrogen isotopes) to high speeds using a two-stage light gas gun

International Nuclear Information System (INIS)

Combs, S.K.; Foust, C.R.; Gouge, M.J.; Milora, S.L.

1989-01-01

Small, light projectiles have been accelerated to high speeds using a two-stage light gas gun at Oak Ridge National Laboratory. With 35-mg plastic projectiles (4 mm in diameter), speeds of up to 4.5 km/s have been recorded. The ''pipe gun'' technique for freezing hydrogen isotopes in situ in the gun barrel has been used to accelerate deuterium pellets (nominal diameter of 4 mm) to velocities of up to 2.85 km/s. The primary application of this technology is for plasma fueling of fusion devices via pellet injection of hydrogen isotopes. Conventional pellet injectors are limited to pellet speeds in the range 1-2 km/s. Higher velocities are desirable for plasma fueling applications, and the two-stage pneumatic technique offers performance in a higher velocity regime. However, experimental results indicate that the use of sabots to encase the cryogenic pellets and protect them for the high peak pressures will be required to reliably attain intact pellets at speeds of ∼3 km/s or greater. In some limited tests, lithium hydride pellets were accelerated to speeds of up to 4.2 km/s. Also, repetitive operation of the two-stage gun (four plastic pellets fired at ∼0.5 Hz) was demonstrated for the first time in preliminary tests. The equipment and operation are described, and experimental results and some comparisons with a theoretical model are presented. 17 refs., 6 figs., 2 tabs

Two sampling techniques for game meat

Directory of Open Access Journals (Sweden)

Maretha van der Merwe

2013-03-01

Full Text Available A study was conducted to compare the excision sampling technique used by the export market and the sampling technique preferred by European countries, namely the biotrace cattle and swine test. The measuring unit for the excision sampling was grams (g and square centimetres (cm2 for the swabbing technique. The two techniques were compared after a pilot test was conducted on spiked approved beef carcasses (n = 12 that statistically proved the two measuring units correlated. The two sampling techniques were conducted on the same game carcasses (n = 13 and analyses performed for aerobic plate count (APC, Escherichia coli and Staphylococcus aureus, for both techniques. A more representative result was obtained by swabbing and no damage was caused to the carcass. Conversely, the excision technique yielded fewer organisms and caused minor damage to the carcass. The recovery ratio from the sampling technique improved 5.4 times for APC, 108.0 times for E. coli and 3.4 times for S. aureus over the results obtained from the excision technique. It was concluded that the sampling methods of excision and swabbing can be used to obtain bacterial profiles from both export and local carcasses and could be used to indicate whether game carcasses intended for the local market are possibly on par with game carcasses intended for the export market and therefore safe for human consumption.

Two sampling techniques for game meat.

Science.gov (United States)

van der Merwe, Maretha; Jooste, Piet J; Hoffman, Louw C; Calitz, Frikkie J

2013-03-20

A study was conducted to compare the excision sampling technique used by the export market and the sampling technique preferred by European countries, namely the biotrace cattle and swine test. The measuring unit for the excision sampling was grams (g) and square centimetres (cm2) for the swabbing technique. The two techniques were compared after a pilot test was conducted on spiked approved beef carcasses (n = 12) that statistically proved the two measuring units correlated. The two sampling techniques were conducted on the same game carcasses (n = 13) and analyses performed for aerobic plate count (APC), Escherichia coli and Staphylococcus aureus, for both techniques. A more representative result was obtained by swabbing and no damage was caused to the carcass. Conversely, the excision technique yielded fewer organisms and caused minor damage to the carcass. The recovery ratio from the sampling technique improved 5.4 times for APC, 108.0 times for E. coli and 3.4 times for S. aureus over the results obtained from the excision technique. It was concluded that the sampling methods of excision and swabbing can be used to obtain bacterial profiles from both export and local carcasses and could be used to indicate whether game carcasses intended for the local market are possibly on par with game carcasses intended for the export market and therefore safe for human consumption.

Two-Stage Progressive Femoral Lowering Followed by Cementless Total Hip Arthroplasty for Treating Crowe IV-Hartofilakidis Type 3 Developmental Dysplasia of the Hip.

Science.gov (United States)

Binazzi, Roberto

2015-05-01

High developmental dysplasia of the hip is commonly treated with total hip arthroplasty and shortening osteotomy. We present a two stage technique, consisting of progressive femoral lowering followed by total hip arthroplasty. The clinico-radiographic results of eleven patients (twelve hips) who were operated on with the two-stage technique were evaluated at a mean follow-up of 11 ± 5 years. At the final follow-up, ten patients (eleven hips) had a mean Harris hip score of 85 ± 5 points with no implant loosening. One patient (one hip) was revised at 5 years due to infection. No neurovascular complications were observed in any patients. With this technique, we could place the cup in the anatomical position and obtain complete limb symmetry with excellent clinical results at long-term. Copyright © 2014 Elsevier Inc. All rights reserved.

Two-Stage Latissimus Dorsi Flap with Implant for Unilateral Breast Reconstruction: Getting the Size Right

Directory of Open Access Journals (Sweden)

Jiajun Feng

2016-03-01

Full Text Available BackgroundThe aim of unilateral breast reconstruction after mastectomy is to craft a natural-looking breast with symmetry. The latissimus dorsi (LD flap with implant is an established technique for this purpose. However, it is challenging to obtain adequate volume and satisfactory aesthetic results using a one-stage operation when considering factors such as muscle atrophy, wound dehiscence and excessive scarring. The two-stage reconstruction addresses these difficulties by using a tissue expander to gradually enlarge the skin pocket which eventually holds an appropriately sized implant.MethodsWe analyzed nine patients who underwent unilateral two-stage LD reconstruction. In the first stage, an expander was placed along with the LD flap to reconstruct the mastectomy defect, followed by gradual tissue expansion to achieve overexpansion of the skin pocket. The final implant volume was determined by measuring the residual expander volume after aspirating the excess saline. Finally, the expander was replaced with the chosen implant.ResultsThe average volume of tissue expansion was 460 mL. The resultant expansion allowed an implant ranging in volume from 255 to 420 mL to be placed alongside the LD muscle. Seven patients scored less than six on the relative breast retraction assessment formula for breast symmetry, indicating excellent breast symmetry. The remaining two patients scored between six and eight, indicating good symmetry.ConclusionsThis approach allows the size of the eventual implant to be estimated after the skin pocket has healed completely and the LD muscle has undergone natural atrophy. Optimal reconstruction results were achieved using this approach.

Two technicians apply insulation to S-II second stage

Science.gov (United States)

1964-01-01

Two technicians apply insulation to the outer surface of the S-II second stage booster for the Saturn V moon rocket. The towering 363-foot Saturn V was a multi-stage, multi-engine launch vehicle standing taller than the Statue of Liberty. Altogether, the Saturn V engines produced as much power as 85 Hoover Dams.

Preparation of SnSe thin films by encapsulated selenization; Saput tipis SnSe disediakan dengan kaedah penselenidan tertudung-tebat

Energy Technology Data Exchange (ETDEWEB)

Sabar, D Hutagalung [Universitas Sumatera Utara, Medan (Indonesia). Dept. of Physics; Sakrani, Samsudi; Wahab, Yussof [Universiti Teknologi Malaysia, Skudai, Johor Bahru (Malaysia). Dept. of Physics

1994-12-31

Tin selenide thin films were prepared by encapsulated selenization. A stacked layer of evaporated Sn and Se films were annealed in a carbon block at temperatures 100 - 500 degree Celsius for 3 hours. X-ray analysis and SEM (Scanning electron) micrograph results showed that SnSe was initially formed at 150 degree Celsius with crystal size 30.0 nm and reached optimum formation at 200 daximum of 57.4 % yield of 5-decene. Other factors such as reaction temperatures, types of solvent and wt% of rhenium loadings influence the activity of the catalytic system.

The effect on esophagus after different radiotherapy techniques for early stage Hodgkin's lymphoma

DEFF Research Database (Denmark)

Jørgensen, Anni; Maraldo, M.; Brodin, Nils Patrik

2013-01-01

The cure rate of early stage Hodgkin's lymphoma (HL) is excellent; investigating the late effects of treatment is thus important. Esophageal toxicity is a known side effect in patients receiving radiotherapy (RT) to the mediastinum, although little is known of this in HL survivors. This study inv...... investigates the dose to the esophagus in the treatment of early stage HL using different RT techniques. Estimated risks of early esophagitis, esophageal stricture and cancer are compared between treatments....

The construction and use of bacterial DNA microarrays based on an optimized two-stage PCR strategy

Directory of Open Access Journals (Sweden)

Pesta David

2003-06-01

Full Text Available Abstract Background DNA microarrays are a powerful tool with important applications such as global gene expression profiling. Construction of bacterial DNA microarrays from genomic sequence data using a two-stage PCR amplification approach for the production of arrayed DNA is attractive because it allows, in principal, the continued re-amplification of DNA fragments and facilitates further utilization of the DNA fragments for additional uses (e.g. over-expression of protein. We describe the successful construction and use of DNA microarrays by the two-stage amplification approach and discuss the technical challenges that were met and resolved during the project. Results Chimeric primers that contained both gene-specific and shared, universal sequence allowed the two-stage amplification of the 3,168 genes identified on the genome of Synechocystis sp. PCC6803, an important prokaryotic model organism for the study of oxygenic photosynthesis. The gene-specific component of the primer was of variable length to maintain uniform annealing temperatures during the 1st round of PCR synthesis, and situated to preserve full-length ORFs. Genes were truncated at 2 kb for efficient amplification, so that about 92% of the PCR fragments were full-length genes. The two-stage amplification had the additional advantage of normalizing the yield of PCR products and this improved the uniformity of DNA features robotically deposited onto the microarray surface. We also describe the techniques utilized to optimize hybridization conditions and signal-to-noise ratio of the transcription profile. The inter-lab transportability was demonstrated by the virtual error-free amplification of the entire genome complement of 3,168 genes using the universal primers in partner labs. The printed slides have been successfully used to identify differentially expressed genes in response to a number of environmental conditions, including salt stress. Conclusions The technique detailed

Investigation of Power Losses of Two-Stage Two-Phase Converter with Two-Phase Motor

Directory of Open Access Journals (Sweden)

Michal Prazenica

2011-01-01

Full Text Available The paper deals with determination of losses of two-stage power electronic system with two-phase variable orthogonal output. The simulation is focused on the investigation of losses in the converter during one period in steady-state operation. Modeling and simulation of two matrix converters with R-L load is shown in the paper. The simulation results confirm a very good time-waveform of the phase current and the system seems to be suitable for low-cost application in automotive/aerospace industries and in application with high frequency voltage sources.

Device for two-stage cementing of casing

Energy Technology Data Exchange (ETDEWEB)

Kudimov, D A; Goncharevskiy, Ye N; Luneva, L G; Shchelochkov, S N; Shil' nikova, L N; Tereshchenko, V G; Vasiliev, V A; Volkova, V V; Zhdokov, K I

1981-01-01

A device is claimed for two-stage cementing of casing. It consists of a body with lateral plugging vents, upper and lower movable sleeves, a check valve with axial channels that's situated in the lower sleeve, and a displacement limiting device for the lower sleeve. To improve the cementing process of the casing by preventing overflow of cementing fluids from the annular space into the first stage casing, the limiter is equipped with a spring rod that is capable of covering the axial channels of the check valve while it's in an operating mode. In addition, the rod in the upper part is equipped with a reinforced area under the axial channels of the check valve.

Tendon 'turnover lengthening' technique.

Science.gov (United States)

Cerovac, S; Miranda, B H

2013-11-01

Tendon defect reconstruction is amongst the most technically challenging areas in hand surgery. Tendon substance deficiency reconstruction techniques include lengthening, grafting, two-stage reconstruction and tendon transfers, however each is associated with unique challenges over and above direct repair. We describe a novel 'turnover lengthening' technique for hand tendons that has successfully been applied to the repair of several cases, including a case of attritional flexor and traumatic extensor tendon rupture in two presented patients where primary tenorrhaphy was not possible. In both cases a good post-operative outcome was achieved, as the patients were happy having returned back to normal activities of daily living such that they were discharged 12 weeks post-operatively. Our technique avoids the additional morbidity and complications associated with grafting, transfers and two stage reconstructions. It is quick, simple and reproducible for defects not exceeding 3-4 cm, provides a means of immediate one stage reconstruction, no secondary donor site morbidity and does not compromise salvage by tendon transfer and/or two-stage reconstruction in cases of failure. To our knowledge no such technique has been previously been described to reconstruct such hand tendon defects. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Optimization of Two-Stage Peltier Modules: Structure and Exergetic Efficiency

Directory of Open Access Journals (Sweden)

Cesar Ramirez-Lopez

2012-08-01

Full Text Available In this paper we undertake the theoretical analysis of a two-stage semiconductor thermoelectric module (TEM which contains an arbitrary and different number of thermocouples, n₁ and n₂, in each stage (pyramid-styled TEM. The analysis is based on a dimensionless entropy balance set of equations. We study the effects of n₁ and n₂, the flowing electric currents through each stage, the applied temperatures and the thermoelectric properties of the semiconductor materials on the exergetic efficiency. Our main result implies that the electric currents flowing in each stage must necessarily be different with a ratio about 4.3 if the best thermal performance and the highest temperature difference possible between the cold and hot side of the device are pursued. This fact had not been pointed out before for pyramid-styled two stage TEM. The ratio n₁/n₂ should be about 8.

An automated technique to stage lower third molar development on panoramic radiographs for age estimation: a pilot study.

Science.gov (United States)

De Tobel, J; Radesh, P; Vandermeulen, D; Thevissen, P W

2017-12-01

Automated methods to evaluate growth of hand and wrist bones on radiographs and magnetic resonance imaging have been developed. They can be applied to estimate age in children and subadults. Automated methods require the software to (1) recognise the region of interest in the image(s), (2) evaluate the degree of development and (3) correlate this to the age of the subject based on a reference population. For age estimation based on third molars an automated method for step (1) has been presented for 3D magnetic resonance imaging and is currently being optimised (Unterpirker et al. 2015). To develop an automated method for step (2) based on lower third molars on panoramic radiographs. A modified Demirjian staging technique including ten developmental stages was developed. Twenty panoramic radiographs per stage per gender were retrospectively selected for FDI element 38. Two observers decided in consensus about the stages. When necessary, a third observer acted as a referee to establish the reference stage for the considered third molar. This set of radiographs was used as training data for machine learning algorithms for automated staging. First, image contrast settings were optimised to evaluate the third molar of interest and a rectangular bounding box was placed around it in a standardised way using Adobe Photoshop CC 2017 software. This bounding box indicated the region of interest for the next step. Second, several machine learning algorithms available in MATLAB R2017a software were applied for automated stage recognition. Third, the classification performance was evaluated in a 5-fold cross-validation scenario, using different validation metrics (accuracy, Rank-N recognition rate, mean absolute difference, linear kappa coefficient). Transfer Learning as a type of Deep Learning Convolutional Neural Network approach outperformed all other tested approaches. Mean accuracy equalled 0.51, mean absolute difference was 0.6 stages and mean linearly weighted kappa was

Repetitive, small-bore two-stage light gas gun

International Nuclear Information System (INIS)

Combs, S.K.; Foust, C.R.; Fehling, D.T.; Gouge, M.J.; Milora, S.L.

1991-01-01

A repetitive two-stage light gas gun for high-speed pellet injection has been developed at Oak Ridge National Laboratory. In general, applications of the two-stage light gas gun have been limited to only single shots, with a finite time (at least minutes) needed for recovery and preparation for the next shot. The new device overcomes problems associated with repetitive operation, including rapidly evacuating the propellant gases, reloading the gun breech with a new projectile, returning the piston to its initial position, and refilling the first- and second-stage gas volumes to the appropriate pressure levels. In addition, some components are subjected to and must survive severe operating conditions, which include rapid cycling to high pressures and temperatures (up to thousands of bars and thousands of kelvins) and significant mechanical shocks. Small plastic projectiles (4-mm nominal size) and helium gas have been used in the prototype device, which was equipped with a 1-m-long pump tube and a 1-m-long gun barrel, to demonstrate repetitive operation (up to 1 Hz) at relatively high pellet velocities (up to 3000 m/s). The equipment is described, and experimental results are presented. 124 refs., 6 figs., 5 tabs

Two-Stage Liver Transplantation with Temporary Porto-Middle Hepatic Vein Shunt

Directory of Open Access Journals (Sweden)

Giovanni Varotti

2010-01-01

Full Text Available Two-stage liver transplantation (LT has been reported for cases of fulminant liver failure that can lead to toxic hepatic syndrome, or massive hemorrhages resulting in uncontrollable bleeding. Technically, the first stage of the procedure consists of a total hepatectomy with preservation of the recipient's inferior vena cava (IVC, followed by the creation of a temporary end-to-side porto-caval shunt (TPCS. The second stage consists of removing the TPCS and implanting a liver graft when one becomes available. We report a case of a two-stage total hepatectomy and LT in which a temporary end-to-end anastomosis between the portal vein and the middle hepatic vein (TPMHV was performed as an alternative to the classic end-to-end TPCS. The creation of a TPMHV proved technically feasible and showed some advantages compared to the standard TPCS. In cases in which a two-stage LT with side-to-side caval reconstruction is utilized, TPMHV can be considered as a safe and effective alternative to standard TPCS.

Two-stage perceptual learning to break visual crowding.

Science.gov (United States)

Zhu, Ziyun; Fan, Zhenzhi; Fang, Fang

2016-01-01

When a target is presented with nearby flankers in the peripheral visual field, it becomes harder to identify, which is referred to as crowding. Crowding sets a fundamental limit of object recognition in peripheral vision, preventing us from fully appreciating cluttered visual scenes. We trained adult human subjects on a crowded orientation discrimination task and investigated whether crowding could be completely eliminated by training. We discovered a two-stage learning process with this training task. In the early stage, when the target and flankers were separated beyond a certain distance, subjects acquired a relatively general ability to break crowding, as evidenced by the fact that the breaking of crowding could transfer to another crowded orientation, even a crowded motion stimulus, although the transfer to the opposite visual hemi-field was weak. In the late stage, like many classical perceptual learning effects, subjects' performance gradually improved and showed specificity to the trained orientation. We also found that, when the target and flankers were spaced too finely, training could only reduce, rather than completely eliminate, the crowding effect. This two-stage learning process illustrates a learning strategy for our brain to deal with the notoriously difficult problem of identifying peripheral objects in clutter. The brain first learned to solve the "easy and general" part of the problem (i.e., improving the processing resolution and segmenting the target and flankers) and then tackle the "difficult and specific" part (i.e., refining the representation of the target).

Research on Two-channel Interleaved Two-stage Paralleled Buck DC-DC Converter for Plasma Cutting Power Supply

DEFF Research Database (Denmark)

Yang, Xi-jun; Qu, Hao; Yao, Chen

2014-01-01

As for high power plasma power supply, due to high efficiency and flexibility, multi-channel interleaved multi-stage paralleled Buck DC-DC Converter becomes the first choice. In the paper, two-channel interleaved two- stage paralleled Buck DC-DC Converter powered by three-phase AC power supply...

Production of endo-pectate lyase by two stage cultivation of Erwinia carotovora

Energy Technology Data Exchange (ETDEWEB)

Fukuoka, Satoshi; Kobayashi, Yoshiaki

1987-02-26

The productivity of endo-pectate lyase from Erwinia carotovora GIR 1044 was found to be greatly improved by two stage cultivation: in the first stage the bacterium was grown with an inducing carbon source, e.g., pectin, and in the second stage it was cultivated with glycerol, xylose, or fructose with the addition of monosodium L-glutamate as nitrogen source. In the two stage cultivation using pectin or glycerol as the carbon source the enzyme activity reached 400 units/ml, almost 3 times as much as that of one stage cultivation in a 10 liter fermentor. Using two stage cultivation in the 200 liter fermentor improved enzyme productivity over that in the 10 liter fermentor, with 500 units/ml of activity. Compared with the cultivation in Erlenmeyer flasks, fermentor cultivation improved enzyme productivity. The optimum cultivating conditions were agitation of 480 rpm with aeration of 0.5 vvm at 28 /sup 0/C. (4 figs, 4 tabs, 14 refs)

Chronic infections in hip arthroplasties: comparing risk of reinfection following one-stage and two-stage revision: a systematic review and meta-analysis

Directory of Open Access Journals (Sweden)

Lange J

2012-03-01

Full Text Available Jeppe Lange1,2, Anders Troelsen3, Reimar W Thomsen4, Kjeld Søballe1,51Lundbeck Foundation Centre for Fast-Track Hip and Knee Surgery, Aarhus C, 2Center for Planned Surgery, Silkeborg Regional Hospital, Silkeborg, 3Department of Orthopaedics, Hvidovre Hospital, Hvidovre, 4Department of Clinical Epidemiology, Aarhus University Hospital, Aalborg, 5Department of Orthopaedics, Aarhus University Hospital, Aarhus C, DenmarkBackground: Two-stage revision is regarded by many as the best treatment of chronic infection in hip arthroplasties. Some international reports, however, have advocated one-stage revision. No systematic review or meta-analysis has ever compared the risk of reinfection following one-stage and two-stage revisions for chronic infection in hip arthroplasties.Methods: The review was performed in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analysis. Relevant studies were identified using PubMed and Embase. We assessed studies that included patients with a chronic infection of a hip arthroplasty treated with either one-stage or two-stage revision and with available data on occurrence of reinfections. We performed a meta-analysis estimating absolute risk of reinfection using a random-effects model.Results: We identified 36 studies eligible for inclusion. None were randomized controlled trials or comparative studies. The patients in these studies had received either one-stage revision (n = 375 or two-stage revision (n = 929. Reinfection occurred with an estimated absolute risk of 13.1% (95% confidence interval: 10.0%–17.1% in the one-stage cohort and 10.4% (95% confidence interval: 8.5%–12.7% in the two-stage cohort. The methodological quality of most included studies was considered low, with insufficient data to evaluate confounding factors.Conclusions: Our results may indicate three additional reinfections per 100 reimplanted patients when performing a one-stage versus two-stage revision. However, the

[Pb2F2](SeO4): a heavier analogue of grandreefite, the first layered fluoride selenate

Science.gov (United States)

Charkin, Dmitri O.; Plokhikh, Igor V.; Zadoya, Anastasiya I.; Kazakov, Sergey M.; Zaloga, Alexander N.; Kozin, Michael S.; Depmeier, Wulf; Siidra, Oleg I.

2018-01-01

Co-precipitation of PbF2 and PbSeO4 in weakly acidic media results in the formation of [Pb2F2](SeO4), the selenate analogue of the naturally occurring mineral grandreefite, [Pb2F2](SO4). The new compound is monoclinic, C2/ c, a = 14.0784(2) Å, b = 4.6267(1) Å, c = 8.8628(1) Å, β = 108.98(1)°, V = 545.93(1) Å3. Its structure has been refined from powder data to R B = 1.55%. From thermal studies, it is established that the compound is stable in air up to about 300 °C, after which it gradually converts into a single phase with composition [Pb2O](SeO4), space group C2/ m, and lattice parameters a = 14.0332(1) Å, b = 5.7532(1) Å, c = 7.2113(1) Å, β = 115.07(1)°, V = 527.37(1) Å3. It is the selenate analogue of lanarkite, [Pb2O](SO4), and phoenicochroite, [Pb2O](CrO4), and its crystal structure was refined to R B = 1.21%. The formation of a single decomposition product upon heating in air suggests that this happens by a thermal hydrolysis mechanism, i.e., Pb2F2SeO4 + H2O (vapor) → Pb2OSeO4 + 2HF↑. This relatively low-temperature process involves complete rearrangement of the crystal structure—from a 2D architecture featuring slabs [Pb2F2]2+ formed by fluorine-centered tetrahedra into a structure characterized by 1D motifs based on [OPb2]2+ chains of oxocentered tetrahedra. The comparative crystal chemistry of the obtained anion-centered structural architectures is discussed.

Novel Techniques with the Aid of a Staged CBCT Guided Surgical Protocol

Directory of Open Access Journals (Sweden)

Evdokia Chasioti

2015-01-01

Full Text Available The case report will present some novel techniques for using a “staged” protocol utilizing strategic periodontally involved teeth as transitional abutments in combination with CBCT guided implant surgery. Staging the case prevented premature loading of the grafted sites during the healing phase. A CBCT following a tenting screw guided bone regeneration procedure ensured adequate bone to place an implant fixture. Proper assessment of the CBCT allowed the surgeon to do an osteotome internal sinus lift in an optimum location. The depth of the bone needed for the osteotome sinus floor elevation was planned. The staged appliance allowed these sinus-augmented sites to heal for an extended period of time compared to implants, which were uncovered and loaded at an earlier time frame. The staged protocol and CBCT analysis enabled the immediate implants to be placed in proper alignment to the adjacent fixture. After teeth were extracted, the osseointegrated implants were converted to abutments for the transitional appliance. Finally, the staged protocol allowed for soft tissue enhancement in the implant and pontic areas prior to final insertion of the prosthesis.

A two-stage method for inverse medium scattering

KAUST Repository

Ito, Kazufumi; Jin, Bangti; Zou, Jun

2013-01-01

We present a novel numerical method to the time-harmonic inverse medium scattering problem of recovering the refractive index from noisy near-field scattered data. The approach consists of two stages, one pruning step of detecting the scatterer

Combining evidence from multiple electronic health care databases: performances of one-stage and two-stage meta-analysis in matched case-control studies.

Science.gov (United States)

La Gamba, Fabiola; Corrao, Giovanni; Romio, Silvana; Sturkenboom, Miriam; Trifirò, Gianluca; Schink, Tania; de Ridder, Maria

2017-10-01

Clustering of patients in databases is usually ignored in one-stage meta-analysis of multi-database studies using matched case-control data. The aim of this study was to compare bias and efficiency of such a one-stage meta-analysis with a two-stage meta-analysis. First, we compared the approaches by generating matched case-control data under 5 simulated scenarios, built by varying: (1) the exposure-outcome association; (2) its variability among databases; (3) the confounding strength of one covariate on this association; (4) its variability; and (5) the (heterogeneous) confounding strength of two covariates. Second, we made the same comparison using empirical data from the ARITMO project, a multiple database study investigating the risk of ventricular arrhythmia following the use of medications with arrhythmogenic potential. In our study, we specifically investigated the effect of current use of promethazine. Bias increased for one-stage meta-analysis with increasing (1) between-database variance of exposure effect and (2) heterogeneous confounding generated by two covariates. The efficiency of one-stage meta-analysis was slightly lower than that of two-stage meta-analysis for the majority of investigated scenarios. Based on ARITMO data, there were no evident differences between one-stage (OR = 1.50, CI = [1.08; 2.08]) and two-stage (OR = 1.55, CI = [1.12; 2.16]) approaches. When the effect of interest is heterogeneous, a one-stage meta-analysis ignoring clustering gives biased estimates. Two-stage meta-analysis generates estimates at least as accurate and precise as one-stage meta-analysis. However, in a study using small databases and rare exposures and/or outcomes, a correct one-stage meta-analysis becomes essential. Copyright © 2017 John Wiley & Sons, Ltd.

FIRST DIRECT EVIDENCE OF TWO STAGES IN FREE RECALL

Directory of Open Access Journals (Sweden)

Eugen Tarnow

2015-12-01

Full Text Available I find that exactly two stages can be seen directly in sequential free recall distributions. These distributions show that the first three recalls come from the emptying of working memory, recalls 6 and above come from a second stage and the 4th and 5th recalls are mixtures of the two.A discontinuity, a rounded step function, is shown to exist in the fitted linear slope of the recall distributions as the recall shifts from the emptying of working memory (positive slope to the second stage (negative slope. The discontinuity leads to a first estimate of the capacity of working memory at 4-4.5 items. The total recall is shown to be a linear combination of the content of working memory and items recalled in the second stage with 3.0-3.9 items coming from working memory, a second estimate of the capacity of working memory. A third, separate upper limit on the capacity of working memory is found (3.06 items, corresponding to the requirement that the content of working memory cannot exceed the total recall, item by item. This third limit is presumably the best limit on the average capacity of unchunked working memory.The second stage of recall is shown to be reactivation: The average times to retrieve additional items in free recall obey a linear relationship as a function of the recall probability which mimics recognition and cued recall, both mechanisms using reactivation (Tarnow, 2008.

Simple Digital Control of a Two-Stage PFC Converter Using DSPIC30F Microprocessor

DEFF Research Database (Denmark)

Török, Lajos; Munk-Nielsen, Stig

2010-01-01

The use of dsPIC digital signal controllers (DSC) in Switch Mode Power Supply (SMPS) applications opens new perspectives for cheap and flexible digital control solutions. This paper presents the digital control of a two stage power factor corrector (PFC) converter. The PFC circuit is designed...... and built for 70W rated output power. Average current mode control for boost converter and current programmed control for forward converter are implemented on a dsPIC30F1010. Pulse Width Modulation (PWM) technique is used to drive the switching MOSFETs. Results show that digital solutions with ds...

A two-stage inexact joint-probabilistic programming method for air quality management under uncertainty.

Science.gov (United States)

Lv, Y; Huang, G H; Li, Y P; Yang, Z F; Sun, W

2011-03-01

A two-stage inexact joint-probabilistic programming (TIJP) method is developed for planning a regional air quality management system with multiple pollutants and multiple sources. The TIJP method incorporates the techniques of two-stage stochastic programming, joint-probabilistic constraint programming and interval mathematical programming, where uncertainties expressed as probability distributions and interval values can be addressed. Moreover, it can not only examine the risk of violating joint-probability constraints, but also account for economic penalties as corrective measures against any infeasibility. The developed TIJP method is applied to a case study of a regional air pollution control problem, where the air quality index (AQI) is introduced for evaluation of the integrated air quality management system associated with multiple pollutants. The joint-probability exists in the environmental constraints for AQI, such that individual probabilistic constraints for each pollutant can be efficiently incorporated within the TIJP model. The results indicate that useful solutions for air quality management practices have been generated; they can help decision makers to identify desired pollution abatement strategies with minimized system cost and maximized environmental efficiency. Copyright © 2010 Elsevier Ltd. All rights reserved.

Modal intersection types, two-level languages, and staged synthesis

DEFF Research Database (Denmark)

Henglein, Fritz; Rehof, Jakob

2016-01-01

-linguistic framework for staged program synthesis, where metaprograms are automatically synthesized which, when executed, generate code in a target language. We survey the basic theory of staged synthesis and illustrate by example how a two-level language theory specialized from λ∩ ⎕ can be used to understand......A typed λ-calculus, λ∩ ⎕, is introduced, combining intersection types and modal types. We develop the metatheory of λ∩ ⎕, with particular emphasis on the theory of subtyping and distributivity of the modal and intersection type operators. We describe how a stratification of λ∩ ⎕ leads to a multi...... the process of staged synthesis....

The rationale and technique of staged-volume arteriovenous malformation radiosurgery

International Nuclear Information System (INIS)

Pollock, Bruce E.; Kline, Robert W.; Stafford, Scott L.; Foote, Robert L.; Schomberg, Paula J.

2000-01-01

Purpose: Stereotactic radiosurgery is an effective management strategy for properly selected arteriovenous malformation (AVM) patients. However, the risk of postradiosurgical radiation-related injury generally limits this procedure to patients with AVMs of an average diameter of 3 cm or less. Radiosurgery of large AVMs in a planned staged fashion was undertaken to limit the radiation exposure to the surrounding normal brain. Methods and Materials: Between April 1997 and December 1999, 10 patients with a median AVM volume of 17.4 cm 3 (range, 7.4-53.3 cm 3 ) underwent staged-volume radiosurgery (23 procedures). At the first radiosurgical procedure, the total volume of the AVM is estimated and a dose plan calculated that covers 10 cm 3 -15 cm 3 , or one-half the nidus volume if the AVM is critically located (brainstem, thalamus, or basal ganglia). At 6-month intervals thereafter, radiosurgery was repeated to different portions of the AVM with the previous dose plan(s) being re-created utilizing intracranial landmarks to minimize radiation overlap. Radiosurgical procedures were continued until the entire malformation has been irradiated. Results: The radiation dosimetry of staged-volume AVM radiosurgery was compared to hypothetical single-session procedures for the 10 patients. Staged-volume radiosurgery decreased the 12-Gy volume by an average of 11.1% (range, 4.9-21%) (p < 0.001). The non-AVM 12-Gy volume was reduced by an average of 27.2% (range, 12.5-51.3%) (p < 0.001). Discussion: Staged-volume radiosurgery of large AVMs results in less radiation exposure to the adjacent brain. Further follow-up is needed to determine whether this technique provides a high rate of AVM obliteration while maintaining an acceptable rate of radiation-related complications

Empirical study of classification process for two-stage turbo air classifier in series

Science.gov (United States)

Yu, Yuan; Liu, Jiaxiang; Li, Gang

2013-05-01

The suitable process parameters for a two-stage turbo air classifier are important for obtaining the ultrafine powder that has a narrow particle-size distribution, however little has been published internationally on the classification process for the two-stage turbo air classifier in series. The influence of the process parameters of a two-stage turbo air classifier in series on classification performance is empirically studied by using aluminum oxide powders as the experimental material. The experimental results show the following: 1) When the rotor cage rotary speed of the first-stage classifier is increased from 2 300 r/min to 2 500 r/min with a constant rotor cage rotary speed of the second-stage classifier, classification precision is increased from 0.64 to 0.67. However, in this case, the final ultrafine powder yield is decreased from 79% to 74%, which means the classification precision and the final ultrafine powder yield can be regulated through adjusting the rotor cage rotary speed of the first-stage classifier. 2) When the rotor cage rotary speed of the second-stage classifier is increased from 2 500 r/min to 3 100 r/min with a constant rotor cage rotary speed of the first-stage classifier, the cut size is decreased from 13.16 μm to 8.76 μm, which means the cut size of the ultrafine powder can be regulated through adjusting the rotor cage rotary speed of the second-stage classifier. 3) When the feeding speed is increased from 35 kg/h to 50 kg/h, the "fish-hook" effect is strengthened, which makes the ultrafine powder yield decrease. 4) To weaken the "fish-hook" effect, the equalization of the two-stage wind speeds or the combination of a high first-stage wind speed with a low second-stage wind speed should be selected. This empirical study provides a criterion of process parameter configurations for a two-stage or multi-stage classifier in series, which offers a theoretical basis for practical production.

Two-stage, high power X-band amplifier experiment

International Nuclear Information System (INIS)

Kuang, E.; Davis, T.J.; Ivers, J.D.; Kerslick, G.S.; Nation, J.A.; Schaechter, L.

1993-01-01

At output powers in excess of 100 MW the authors have noted the development of sidebands in many TWT structures. To address this problem an experiment using a narrow bandwidth, two-stage TWT is in progress. The TWT amplifier consists of a dielectric (e = 5) slow-wave structure, a 30 dB sever section and a 8.8-9.0 GHz passband periodic, metallic structure. The electron beam used in this experiment is a 950 kV, 1 kA, 50 ns pencil beam propagating along an applied axial field of 9 kG. The dielectric first stage has a maximum gain of 30 dB measured at 8.87 GHz, with output powers of up to 50 MW in the TM 01 mode. In these experiments the dielectric amplifier output power is about 3-5 MW and the output power of the complete two-stage device is ∼160 MW at the input frequency. The sidebands detected in earlier experiments have been eliminated. The authors also report measurements of the energy spread of the electron beam resulting from the amplification process. These experimental results are compared with MAGIC code simulations and analytic work they have carried out on such devices

Randomised study on single stage laparo-endoscopic rendezvous (intra-operative ERCP) procedure versus two stage approach (Pre-operative ERCP followed by laparoscopic cholecystectomy) for the management of cholelithiasis with choledocholithiasis.

Science.gov (United States)

Sahoo, Manash Ranjan; Kumar, Anil T; Patnaik, Aashish

2014-07-01

The 'Rendezvous' technique consists of laparoscopic cholecystectomy (LC) standards with intra-operative cholangiography followed by endoscopic sphincterotomy. The sphincterotome is driven across the papilla through a guidewire inserted by the transcystic route. In this study, we intended to compare the two methods in a prospective randomised trial. From 2005 to 2012, we enrolled 83 patients with a diagnosis of cholecysto-choledocolithiasis. They were randomised into two groups. In 'group-A',41 patients were treated with two stages management, first by pre-operative endoscopic retrograde cholangiopancreatography (ERCP) and common bile duct (CBD) clearance and second by LC. In 'group-B', 42 patients were treated with LC and intra-operative cholangiography; and when diagnosis of choledocholithiasis was confirmed, patients had undergone one stage management of by Laparo-endoscopic Rendezvous technique. In arm-A and arm-B groups, complete CBD clearance was achieved in 29 and 38 patients, respectively. Failure of the treatment in arm-A was 29% and in arm-B was 9.5%. In arm-A, selective CBD cannulation was achieved in 33 cases (80.5%) and in arm-B in 39 cases (93%). In arm-Agroup, post-ERCP hyperamylasia was presented in nine patients (22%) and severe pancreatitis in five patients (12%) versus none of the patients (0%) in arm-B group, respectively. Mean post-operative hospital stay in arm-A and arm-B groups are 10.9 and 6.8 days, respectively. One stage laparo-endoscopic rendezvous approach increases selective cannulation of CBD, reduces post-ERCP pancreatitis, reduces days of hospital stay, increases patient's compliance and prevents unnecessary intervention to CBD.

Noncausal two-stage image filtration at presence of observations with anomalous errors

OpenAIRE

S. V. Vishnevyy; S. Ya. Zhuk; A. N. Pavliuchenkova

2013-01-01

Introduction. It is necessary to develop adaptive algorithms, which allow to detect such regions and to apply filter with respective parameters for suppression of anomalous noises for the purposes of image filtration, which consist of regions with anomalous errors. Development of adaptive algorithm for non-causal two-stage images filtration at pres-ence of observations with anomalous errors. The adaptive algorithm for noncausal two-stage filtration is developed. On the first stage the adaptiv...

CFD simulations of compressed air two stage rotary Wankel expander – Parametric analysis

International Nuclear Information System (INIS)

Sadiq, Ghada A.; Tozer, Gavin; Al-Dadah, Raya; Mahmoud, Saad

2017-01-01

Highlights: • CFD ANSYS-Fluent 3D simulation of Wankel expander is developed. • Single and two-stage expander’s performance is compared. • Inlet and outlet ports shape and configurations are investigated. • Isentropic efficiency of two stage Wankel expander of 91% is achieved. - Abstract: A small scale volumetric Wankel expander is a powerful device for small-scale power generation in compressed air energy storage (CAES) systems and Organic Rankine cycles powered by different heat sources such as, biomass, low temperature geothermal, solar and waste heat leading to significant reduction in CO_2 emissions. Wankel expanders outperform other types of expander due to their ability to produce two power pulses per revolution per chamber additional to higher compactness, lower noise and vibration and lower cost. In this paper, a computational fluid dynamics (CFD) model was developed using ANSYS 16.2 to simulate the flow dynamics for a single and two stage Wankel expanders and to investigate the effect of port configurations, including size and spacing, on the expander’s power output and isentropic efficiency. Also, single-stage and two-stage expanders were analysed with different operating conditions. Single-stage 3D CFD results were compared to published work showing close agreement. The CFD modelling was used to investigate the performance of the rotary device using air as an ideal gas with various port diameters ranging from 15 mm to 50 mm; port spacing varying from 28 mm to 66 mm; different Wankel expander sizes (r = 48, e = 6.6, b = 32) mm and (r = 58, e = 8, b = 40) mm both as single-stage and as two-stage expanders with different configurations and various operating conditions. Results showed that the best Wankel expander design for a single-stage was (r = 48, e = 6.6, b = 32) mm, with the port diameters 20 mm and port spacing equal to 50 mm. Moreover, combining two Wankel expanders horizontally, with a larger one at front, produced 8.52 kW compared

Modeling and Implementing Two-Stage AdaBoost for Real-Time Vehicle License Plate Detection

Directory of Open Access Journals (Sweden)

Moon Kyou Song

2014-01-01

Full Text Available License plate (LP detection is the most imperative part of the automatic LP recognition system. In previous years, different methods, techniques, and algorithms have been developed for LP detection (LPD systems. This paper proposes to automatical detection of car LPs via image processing techniques based on classifier or machine learning algorithms. In this paper, we propose a real-time and robust method for LPD systems using the two-stage adaptive boosting (AdaBoost algorithm combined with different image preprocessing techniques. Haar-like features are used to compute and select features from LP images. The AdaBoost algorithm is used to classify parts of an image within a search window by a trained strong classifier as either LP or non-LP. Adaptive thresholding is used for the image preprocessing method applied to those images that are of insufficient quality for LPD. This method is of a faster speed and higher accuracy than most of the existing methods used in LPD. Experimental results demonstrate that the average LPD rate is 98.38% and the computational time is approximately 49 ms.

The Voltammetric Analysis of Selenium Electrodeposition from H2SeO3 Solution on Gold Electrode

OpenAIRE

Kowalik R.

2015-01-01

The different voltammetry techniques were applied to understand the process of selenium deposition from sulfate solution on gold polycrystalline electrode. By applying the cycling voltammetry with different scan limits as well as the chronoamper-ometry combined with the cathodic and anodic linear stripping voltammetry, the different stages of the deposition of selenium were revealed. It was found that the process of reduction of selenous acid on gold surface exhibits a multistage character. T...

Automatic Diagnose of the Stages of Breast Cancer using Intelligent Technique

Science.gov (United States)

Jiji, G. W.; Marsilin, J. R.

2012-12-01

The objective of this paper is to locate the stage of the breast cancer and to locate the tumor tissues. The proposed work is performed in two stages. In the first stage, location of tumour is done and in the second phase retrieving of the tumor images and its stages based on the "query input". Texture and Shape features are used here as Feature descriptors. Shape features used are asymmetry, aspect ratio, eccentricity and Bending Energy. Texture features used are contrast, energy and Gabor Filter. KNN classifier is used for classification and for Pattern matching, Euclidean distance is used. The proposed approach which gives 95.6% accuracy has been compared with earlier approaches. The proposed approach was tested with 32 samples and got annotated by radiologists.

Multi stage electrodialysis for separation of two metal ion species

Energy Technology Data Exchange (ETDEWEB)

Takahashi, K.; Sakurai, H.; Nii, S.; Sugiura, K. [Nagoya Univ., Nagoya (Japan)

1995-04-20

In this article, separation of two metal ions by electrodialysis with a cation exchange membrane has been investigated. In other words, separation of potassium ion and sodium ion has been investigated by using batch dialysis with and without an electric field and continuous electrodialysis with a four-stage dialyzer. As a result, the difference in the permselectivity between the dialysis with and without an electric field has not been appreciable for the system of potassium and sodium ions with the cation exchange membrane. Concerning the continuous electrodialysis, the concentration ratio between potassium and sodium ions in the outlet solution from the recovery side of the dialyzer has increased with the reflux flow rate and the number of stages. In case when the reflux flow rate has been zero, the concentration ratio with the four-stage dialyzer has become 1.5 which is almost the same as with that with a two-stage dialyzer consisting of a simple membrane. When the reflux flow ratio has been 0.7, the concentration ratio has reached 3.6. 20 refs., 8 figs.

Hybrid biogas upgrading in a two-stage thermophilic reactor

DEFF Research Database (Denmark)

Corbellini, Viola; Kougias, Panagiotis; Treu, Laura

2018-01-01

The aim of this study is to propose a hybrid biogas upgrading configuration composed of two-stage thermophilic reactors. Hydrogen is directly injected in the first stage reactor. The output gas from the first reactor (in-situ biogas upgrade) is subsequently transferred to a second upflow reactor...... (ex-situ upgrade), in which enriched hydrogenotrophic culture is responsible for the hydrogenation of carbon dioxide to methane. The overall objective of the work was to perform an initial methane enrichment in the in-situ reactor, avoiding deterioration of the process due to elevated pH levels......, and subsequently, to complete the biogas upgrading process in the ex-situ chamber. The methane content in the first stage reactor reached on average 87% and the corresponding value in the second stage was 91%, with a maximum of 95%. A remarkable accumulation of volatile fatty acids was observed in the first...

Two-stage gas-phase bioreactor for the combined removal of hydrogen sulphide, methanol and alpha-pinene.

Science.gov (United States)

Rene, Eldon R; Jin, Yaomin; Veiga, María C; Kennes, Christian

2009-11-01

Biological treatment systems have emerged as cost-effective and eco-friendly techniques for treating waste gases from process industries at moderately high gas flow rates and low pollutant concentrations. In this study, we have assessed the performance of a two-stage bioreactor, namely a biotrickling filter packed with pall rings (BTF, 1st stage) and a perlite + pall ring mixed biofilter (BF, 2nd stage) operated in series, for handling a complex mixture of hydrogen sulphide (H2S), methanol (CH3OH) and alpha-pinene (C10H16). It has been reported that the presence of H2S can reduce the biofiltration efficiency of volatile organic compounds (VOCs) when both are present in the gas mixture. Hydrogen sulphide and methanol were removed in the first stage BTF, previously inoculated with H2S-adapted populations and a culture containing Candida boidinii, an acid-tolerant yeast, whereas, in the second stage, alpha-pinene was removed predominantly by the fungus Ophiostoma stenoceras. Experiments were conducted in five different phases, corresponding to inlet loading rates varying between 2.1 and 93.5 g m(-3) h(-1) for H2S, 55.3 and 1260.2 g m(-3) h(-1) for methanol, and 2.8 and 161.1 g m(-3) h(-1) for alpha-pinene. Empty bed residence times were varied between 83.4 and 10 s in the first stage and 146.4 and 17.6 s in the second stage. The BTF, working at a pH as low as 2.7 as a result of H2S degradation, removed most of the H2S and methanol but only very little alpha-pinene. On the other hand, the BF, at a pH around 6.0, removed the rest of the H2S, the non-degraded methanol and most of the alpha-pinene vapours. Attempts were originally made to remove the three pollutants in a single acidophilic bioreactor, but the Ophiostoma strain was hardly active at pH elimination capacities (ECs) reached by the two-stage bioreactor for individual pollutants were 894.4 g m(-3) h(-1) for methanol, 45.1 g m(-3) h(-1) for H2S and 138.1 g m(-3) h(-1) for alpha-pinene. The results from this

Runway Operations Planning: A Two-Stage Solution Methodology

Science.gov (United States)

Anagnostakis, Ioannis; Clarke, John-Paul

2003-01-01

The airport runway is a scarce resource that must be shared by different runway operations (arrivals, departures and runway crossings). Given the possible sequences of runway events, careful Runway Operations Planning (ROP) is required if runway utilization is to be maximized. Thus, Runway Operations Planning (ROP) is a critical component of airport operations planning in general and surface operations planning in particular. From the perspective of departures, ROP solutions are aircraft departure schedules developed by optimally allocating runway time for departures given the time required for arrivals and crossings. In addition to the obvious objective of maximizing throughput, other objectives, such as guaranteeing fairness and minimizing environmental impact, may be incorporated into the ROP solution subject to constraints introduced by Air Traffic Control (ATC) procedures. Generating optimal runway operations plans was approached in with a 'one-stage' optimization routine that considered all the desired objectives and constraints, and the characteristics of each aircraft (weight class, destination, Air Traffic Control (ATC) constraints) at the same time. Since, however, at any given point in time, there is less uncertainty in the predicted demand for departure resources in terms of weight class than in terms of specific aircraft, the ROP problem can be parsed into two stages. In the context of the Departure Planner (OP) research project, this paper introduces Runway Operations Planning (ROP) as part of the wider Surface Operations Optimization (SOO) and describes a proposed 'two stage' heuristic algorithm for solving the Runway Operations Planning (ROP) problem. Focus is specifically given on including runway crossings in the planning process of runway operations. In the first stage, sequences of departure class slots and runwy crossings slots are generated and ranked based on departure runway throughput under stochastic conditions. In the second stage, the

Strain preservation of experimental animals: vitrification of two-cell stage embryos for multiple mouse strains.

Science.gov (United States)

Eto, Tomoo; Takahashi, Riichi; Kamisako, Tsutomu

2015-04-01

Strain preservation of experimental animals is crucial for experimental reproducibility. Maintaining complete animal strains, however, is costly and there is a risk for genetic mutations as well as complete loss due to disasters or illness. Therefore, the development of effective vitrification techniques for cryopreservation of multiple experimental animal strains is important. We examined whether a vitrification method using cryoprotectant solutions, P10 and PEPeS, is suitable for preservation of multiple inbred and outbred mouse strains. First, we investigated whether our vitrification method using cryoprotectant solutions was suitable for two-cell stage mouse embryos. In vitro development of embryos exposed to the cryoprotectant solutions was similar to that of fresh controls. Further, the survival rate of the vitrified embryos was extremely high (98.1%). Next, we collected and vitrified two-cell stage embryos of 14 mouse strains. The average number of embryos obtained from one female was 7.3-33.3. The survival rate of vitrified embryos ranged from 92.8% to 99.1%, with no significant differences among mouse strains. In vivo development did not differ significantly between fresh controls and vitrified embryos of each strain. For strain preservation using cryopreserved embryos, two offspring for inbred lines and one offspring for outbred lines must be produced from two-cell stage embryos collected from one female. The expected number of surviving fetuses obtained from embryos collected from one female of either the inbred or outbred strains ranged from 2.9 to 19.5. The findings of the present study indicated that this vitrification method is suitable for strain preservation of multiple mouse strains. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Single-stage versus two-stage anaerobic fluidized bed bioreactors in treating municipal wastewater: Performance, foulant characteristics, and microbial community.

Science.gov (United States)

Wu, Bing; Li, Yifei; Lim, Weikang; Lee, Shi Lin; Guo, Qiming; Fane, Anthony G; Liu, Yu

2017-03-01

This study examined the receptive performance, membrane foulant characteristics, and microbial community in the single-stage and two-stage anaerobic fluidized membrane bioreactor (AFMBR) treating settled raw municipal wastewater with the aims to explore fouling mechanisms and microbial community structure in both systems. Both AFMBRs exhibited comparable organic removal efficiency and membrane performances. In the single-stage AFMBR, less soluble organic substances were removed through biosorption by GAC and biodegradation than those in the two-stage AFMBR. Compared to the two-stage AFMBR, the formation of cake layer was the main cause of the observed membrane fouling in the single-stage AFMBR at the same employed flux. The accumulation rate of the biopolymers was linearly correlated with the membrane fouling rate. In the chemical-cleaned foulants, humic acid-like substances and silicon were identified as the predominant organic and inorganic fouants respectively. As such, the fluidized GAC particles might not be effective in removing these substances from the membrane surfaces. High-throughout pyrosequencing analysis further revealed that beta-Proteobacteria were predominant members in both AFMBRs, which contributed to the development of biofilms on the fluidized GAC and membrane surfaces. However, it was also noted that the abundance of the identified dominant in the membrane surface-associated biofilm seemed to be related to the permeate flux and reactor configuration. Copyright © 2016 Elsevier Ltd. All rights reserved.

TWO-STAGE HEAT PUMPS FOR ENERGY SAVING TECHNOLOGIES

Directory of Open Access Journals (Sweden)

A. E. Denysova

2017-09-01

Full Text Available The problem of energy saving becomes one of the most important in power engineering. It is caused by exhaustion of world reserves in hydrocarbon fuel, such as gas, oil and coal representing sources of traditional heat supply. Conventional sources have essential shortcomings: low power, ecological and economic efficiencies, that can be eliminated by using alternative methods of power supply, like the considered one: low-temperature natural heat of ground waters of on the basis of heat pump installations application. The heat supply system considered provides an effective use of two stages heat pump installation operating as heat source at ground waters during the lowest ambient temperature period. Proposed is a calculation method of heat pump installations on the basis of groundwater energy. Calculated are the values of electric energy consumption by the compressors’ drive, and the heat supply system transformation coefficient µ for a low-potential source of heat from ground waters allowing to estimate high efficiency of two stages heat pump installations.

Development and testing of a two stage granular filter to improve collection efficiency

Energy Technology Data Exchange (ETDEWEB)

Rangan, R.S.; Prakash, S.G.; Chakravarti, S.; Rao, S.R.

1999-07-01

A circulating bed granular filter (CBGF) with a single filtration stage was tested with a PFB combustor in the Coal Research Facility of BHEL R and D in Hyderabad during the years 1993--95. Filter outlet dust loading varied between 20--50 mg/Nm{sup 3} for an inlet dust loading of 5--8 gms/Nm{sup 3}. The results were reported in Fluidized Bed Combustion-Volume 2, ASME 1995. Though the outlet consists of predominantly fine particulates below 2 microns, it is still beyond present day gas turbine specifications for particulate concentration. In order to enhance the collection efficiency, a two-stage granular filtration concept was evolved, wherein the filter depth is divided between two stages, accommodated in two separate vertically mounted units. The design also incorporates BHEL's scale-up concept of multiple parallel stages. The two-stage concept minimizes reentrainment of captured dust by providing clean granules in the upper stage, from where gases finally exit the filter. The design ensures that dusty gases come in contact with granules having a higher dust concentration at the bottom of the two-stage unit, where most of the cleaning is completed. A second filtration stage of cleaned granules is provided in the top unit (where the granules are returned to the system after dedusting) minimizing reentrainment. Tests were conducted to determine the optimum granule to dust ratio (G/D ratio) which decides the granule circulation rate required for the desired collection efficiency. The data brings out the importance of pre-separation and the limitation on inlet dust loading for any continuous system of granular filtration. Collection efficiencies obtained were much higher (outlet dust being 3--9 mg/Nm{sub 3}) than in the single stage filter tested earlier for similar dust loading at the inlet. The results indicate that two-stage granular filtration has a high potential for HTHT application with fewer risks as compared to other systems under development.

Automatic sleep stage classification using two facial electrodes.

Science.gov (United States)

Virkkala, Jussi; Velin, Riitta; Himanen, Sari-Leena; Värri, Alpo; Müller, Kiti; Hasan, Joel

2008-01-01

Standard sleep stage classification is based on visual analysis of central EEG, EOG and EMG signals. Automatic analysis with a reduced number of sensors has been studied as an easy alternative to the standard. In this study, a single-channel electro-oculography (EOG) algorithm was developed for separation of wakefulness, SREM, light sleep (S1, S2) and slow wave sleep (S3, S4). The algorithm was developed and tested with 296 subjects. Additional validation was performed on 16 subjects using a low weight single-channel Alive Monitor. In the validation study, subjects attached the disposable EOG electrodes themselves at home. In separating the four stages total agreement (and Cohen's Kappa) in the training data set was 74% (0.59), in the testing data set 73% (0.59) and in the validation data set 74% (0.59). Self-applicable electro-oculography with only two facial electrodes was found to provide reasonable sleep stage information.

Development of Explosive Ripper with Two-Stage Combustion

Science.gov (United States)

1974-10-01

inch pipe duct work, the width of this duct proved to be detrimental in marginally rippable material; the duct, instead of the penetrator tip, was...marginally rippable rock. ID. Operating Requirements 2. Fuel The two-stage combustion device is designed to operate using S A 42. the same diesel

Kinetics analysis of two-stage austenitization in supermartensitic stainless steel

DEFF Research Database (Denmark)

Nießen, Frank; Villa, Matteo; Hald, John

2017-01-01

The martensite-to-austenite transformation in X4CrNiMo16-5-1 supermartensitic stainless steel was followed in-situ during isochronal heating at 2, 6 and 18 K min−1 applying energy-dispersive synchrotron X-ray diffraction at the BESSY II facility. Austenitization occurred in two stages, separated...... that the austenitization kinetics is governed by Ni-diffusion and that slow transformation kinetics separating the two stages is caused by soft impingement in the martensite phase. Increasing the lath width in the kinetics model had a similar effect on the austenitization kinetics as increasing the heating-rate....

Randomised study on single stage laparo-endoscopic rendezvous (intra-operative ERCP procedure versus two stage approach (Pre-operative ERCP followed by laparoscopic cholecystectomy for the management of cholelithiasis with choledocholithiasis

Directory of Open Access Journals (Sweden)

Manash Ranjan Sahoo

2014-01-01

Full Text Available Introduction : The ′Rendezvous′ technique consists of laparoscopic cholecystectomy (LC standards with intra-operative cholangiography followed by endoscopic sphincterotomy. The sphincterotome is driven across the papilla through a guidewire inserted by the transcystic route. In this study, we intended to compare the two methods in a prospective randomised trial. Materials And Methods: From 2005 to 2012, we enrolled 83 patients with a diagnosis of cholecysto-choledocolithiasis. They were randomised into two groups. In ′group-A′,41 patients were treated with two stages management, first by pre-operative endoscopic retrograde cholangiopancreatography (ERCP and common bile duct (CBD clearance and second by LC. In ′group-B′, 42 patients were treated with LC and intra-operative cholangiography; and when diagnosis of choledocholithiasis was confirmed, patients had undergone one stage management of by Laparo-endoscopic Rendezvous technique. Results: In arm-A and arm-B groups, complete CBD clearance was achieved in 29 and 38 patients, respectively. Failure of the treatment in arm-A was 29% and in arm-B was 9.5%. In arm-A, selective CBD cannulation was achieved in 33 cases (80.5% and in arm-B in 39 cases (93%. In arm-Agroup, post-ERCP hyperamylasia was presented in nine patients (22% and severe pancreatitis in five patients (12% versus none of the patients (0% in arm-B group, respectively. Mean post-operative hospital stay in arm-A and arm-B groups are 10.9 and 6.8 days, respectively. Conclusion: One stage laparo-endoscopic rendezvous approach increases selective cannulation of CBD, reduces post-ERCP pancreatitis, reduces days of hospital stay, increases patient′s compliance and prevents unnecessary intervention to CBD.

An adaptive two-stage dose-response design method for establishing proof of concept.

Science.gov (United States)

Franchetti, Yoko; Anderson, Stewart J; Sampson, Allan R

2013-01-01

We propose an adaptive two-stage dose-response design where a prespecified adaptation rule is used to add and/or drop treatment arms between the stages. We extend the multiple comparison procedures-modeling (MCP-Mod) approach into a two-stage design. In each stage, we use the same set of candidate dose-response models and test for a dose-response relationship or proof of concept (PoC) via model-associated statistics. The stage-wise test results are then combined to establish "global" PoC using a conditional error function. Our simulation studies showed good and more robust power in our design method compared to conventional and fixed designs.

Two-staged management for all types of congenital pouch colon

Directory of Open Access Journals (Sweden)

Rajendra K Ghritlaharey

2013-01-01

Full Text Available Background: The aim of this study was to review our experience with two-staged management for all types of congenital pouch colon (CPC. Patients and Methods: This retrospective study included CPC cases that were managed with two-staged procedures in the Department of Paediatric Surgery, over a period of 12 years from 1 January 2000 to 31 December 2011. Results: CPC comprised of 13.71% (97 of 707 of all anorectal malformations (ARM and 28.19% (97 of 344 of high ARM. Eleven CPC cases (all males were managed with two-staged procedures. Distribution of cases (Narsimha Rao et al.′s classification into types I, II, III, and IV were 1, 2, 6, and 2, respectively. Initial operative procedures performed were window colostomy (n = 6, colostomy proximal to pouch (n = 4, and ligation of colovesical fistula and end colostomy (n = 1. As definitive procedures, pouch excision with abdomino-perineal pull through (APPT of colon in eight, and pouch excision with APPT of ileum in three were performed. The mean age at the time of definitive procedures was 15.6 months (ranges from 3 to 53 months and the mean weight was 7.5 kg (ranges from 4 to 11 kg. Good fecal continence was observed in six and fair in two cases in follow-up periods, while three of our cases lost to follow up. There was no mortality following definitive procedures amongst above 11 cases. Conclusions: Two-staged procedures for all types of CPC can also be performed safely with good results. The most important fact that the definitive procedure is being done without protective stoma and therefore, it avoids stoma closure, stoma-related complications, related cost of stoma closure and hospital stay.

A two-stage preventive maintenance optimization model incorporating two-dimensional extended warranty

International Nuclear Information System (INIS)

Su, Chun; Wang, Xiaolin

2016-01-01

In practice, customers can decide whether to buy an extended warranty or not, at the time of item sale or at the end of the basic warranty. In this paper, by taking into account the moments of customers purchasing two-dimensional extended warranty, the optimization of imperfect preventive maintenance for repairable items is investigated from the manufacturer's perspective. A two-dimensional preventive maintenance strategy is proposed, under which the item is preventively maintained according to a specified age interval or usage interval, whichever occurs first. It is highlighted that when the extended warranty is purchased upon the expiration of the basic warranty, the manufacturer faces a two-stage preventive maintenance optimization problem. Moreover, in the second stage, the possibility of reducing the servicing cost over the extended warranty period is explored by classifying customers on the basis of their usage rates and then providing them with customized preventive maintenance programs. Numerical examples show that offering customized preventive maintenance programs can reduce the manufacturer's warranty cost, while a larger saving in warranty cost comes from encouraging customers to buy the extended warranty at the time of item sale. - Highlights: • A two-dimensional PM strategy is investigated. • Imperfect PM strategy is optimized by considering both two-dimensional BW and EW. • Customers are categorized based on their usage rates throughout the BW period. • Servicing cost of the EW is reduced by offering customized PM programs. • Customers buying the EW at the time of sale is preferred for the manufacturer.

Two-stage agglomeration of fine-grained herbal nettle waste

Science.gov (United States)

Obidziński, Sławomir; Joka, Magdalena; Fijoł, Olga

2017-10-01

This paper compares the densification work necessary for the pressure agglomeration of fine-grained dusty nettle waste, with the densification work involved in two-stage agglomeration of the same material. In the first stage, the material was pre-densified through coating with a binder material in the form of a 5% potato starch solution, and then subjected to pressure agglomeration. A number of tests were conducted to determine the effect of the moisture content in the nettle waste (15, 18 and 21%), as well as the process temperature (50, 70, 90°C) on the values of densification work and the density of the obtained pellets. For pre-densified pellets from a mixture of nettle waste and a starch solution, the conducted tests determined the effect of pellet particle size (1, 2, and 3 mm) and the process temperature (50, 70, 90°C) on the same values. On the basis of the tests, we concluded that the introduction of a binder material and the use of two-stage agglomeration in nettle waste densification resulted in increased densification work (as compared to the densification of nettle waste alone) and increased pellet density.

Two-stage hepatectomy: who will not jump over the second hurdle?

Science.gov (United States)

Turrini, O; Ewald, J; Viret, F; Sarran, A; Goncalves, A; Delpero, J-R

2012-03-01

Two-stage hepatectomy uses compensatory liver regeneration after a first noncurative hepatectomy to enable a second curative resection in patients with bilobar colorectal liver metastasis (CLM). To determine the predictive factors of failure of two-stage hepatectomy. Between 2000 and 2010, 48 patients with irresectable CLM were eligible for two-stage hepatectomy. The planned strategy was a) cleaning of the left hepatic lobe (first hepatectomy), b) right portal vein embolisation and c) right hepatectomy (second hepatectomy). Six patients had occult CLM (n = 5) or extra-hepatic disease (n = 1), which was discovered during the first hepatectomy. Thus, 42 patients completed the first hepatectomy and underwent portal vein embolisation in order to receive the second hepatectomy. Eight patients did not undergo a second hepatectomy due to disease progression. Upon univariate analysis, two factors were identified that precluded patients from having the second hepatectomy: the combined resection of a primary tumour during the first hepatectomy (p = 0.01) and administration of chemotherapy between the two hepatectomies (p = 0.03). An independent association with impairment to perform the two-stage strategy was demonstrated by multivariate analysis for only the combined resection of the primary colorectal cancer during the first hepatectomy (p = 0.04). Due to the small number of patients and the absence of equivalent conclusions in other studies, we cannot recommend performance of an isolated colorectal resection prior to chemotherapy. However, resection of an asymptomatic primary tumour before chemotherapy should not be considered as an outdated procedure. Copyright © 2011 Elsevier Ltd. All rights reserved.

A simple two stage optimization algorithm for constrained power economic dispatch

International Nuclear Information System (INIS)

Huang, G.; Song, K.

1994-01-01

A simple two stage optimization algorithm is proposed and investigated for fast computation of constrained power economic dispatch control problems. The method is a simple demonstration of the hierarchical aggregation-disaggregation (HAD) concept. The algorithm first solves an aggregated problem to obtain an initial solution. This aggregated problem turns out to be classical economic dispatch formulation, and it can be solved in 1% of overall computation time. In the second stage, linear programming method finds optimal solution which satisfies power balance constraints, generation and transmission inequality constraints and security constraints. Implementation of the algorithm for IEEE systems and EPRI Scenario systems shows that the two stage method obtains average speedup ratio 10.64 as compared to classical LP-based method

Texture control and growth mechanism of WSe{sub 2} film prepared by rapid selenization of W film

Energy Technology Data Exchange (ETDEWEB)

Li, Hongchao [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Chongyi Zhangyuan Tungsten Industry Corporation Limited, Ganzhou 341300 (China); Gao, Di; Li, Kun; Pang, Mengde; Xie, Senlin [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Rutie, E-mail: llrrtt@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Zou, Jianpeng [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2017-02-01

Highlights: • We present a highly efficient method for preparing WSe{sub 2} film by rapid selenization. • The W film phase composition has little effect on WSe{sub 2} film orientation. • W film density is a critical factor that influences the WSe{sub 2} orientation. • A growth model was proposed for two kinds of WSe{sub 2} film textures. - Abstract: The tungsten diselenide (WSe{sub 2}) films with different orientation present unique properties suitable for specific applications, such as WSe{sub 2} with a C-axis⊥substrate for optoelectronics and WSe{sub 2} with a C-axis // substrate for electrocatalysts. Orientation control of WSe{sub 2} is essential for realizing the practical applications. In this letter, a WSe{sub 2} film has been prepared via rapid selenization of a magnetron-sputtered tungsten (W) film. The influence of the magnetron-sputtered W film on WSe{sub 2} film growth was studied systematically. Scanning electron microscopy, X-ray diffractometry and high-resolution transmission electron microscopy were used to evaluate the morphology, microstructure and phase composition of the W and WSe{sub 2} films. The substrate temperature has a significant effect on the W film phase composition, but little effect on the WSe{sub 2} film orientation. The WSe{sub 2} orientation can be controlled by changing the W film microstructure. A dense W film that is deposited at low pressure is conducive to the formation of WSe{sub 2} with a C-axis⊥substrate, whereas a porous W film deposited at high pressure favors the formation of WSe{sub 2} with a C-axis // substrate. A growth model for the WSe{sub 2} film with different texture has been proposed based on the experimental results. The direction of selenium (Se) vapor diffusion differs at the top and side surfaces. This is a key factor for the preparation of anisotropic WSe{sub 2} films. Highly oriented WSe{sub 2} films with a C-axis⊥substrate grow from the dense W film deposited at low pressure because Se vapor

Multi-Stage Adaptive Noise Cancellation Technique for Synthetic Hard-α Inclusion

International Nuclear Information System (INIS)

Kim, Jae Joon

2003-01-01

Adaptive noise cancellation techniques are ideally suitable for reducing spatially varying noise due to the grain structure of material in ultrasonic nondestructive evaluation. Grain noises have an un-correlation property, while flaw echoes are correlated. Thus, adaptive filtering algorithms use the correlation properties of signals to enhance the signal-to-noise ratio (SNR) of the output signal. In this paper, a multi-stage adaptive noise cancellation (MANC) method using adaptive least mean square error (LMSE) filter for enhancing flaw detection in ultrasonic signals is proposed

A CURRENT MIRROR BASED TWO STAGE CMOS CASCODE OP-AMP FOR HIGH FREQUENCY APPLICATION

Directory of Open Access Journals (Sweden)

RAMKRISHNA KUNDU

2017-03-01

Full Text Available This paper presents a low power, high slew rate, high gain, ultra wide band two stage CMOS cascode operational amplifier for radio frequency application. Current mirror based cascoding technique and pole zero cancelation technique is used to ameliorate the gain and enhance the unity gain bandwidth respectively, which is the novelty of the circuit. In cascading technique a common source transistor drive a common gate transistor. The cascoding is used to enhance the output resistance and hence improve the overall gain of the operational amplifier with less complexity and less power dissipation. To bias the common gate transistor, a current mirror is used in this paper. The proposed circuit is designed and simulated using Cadence analog and digital system design tools of 45 nanometer CMOS technology. The simulated results of the circuit show DC gain of 63.62 dB, unity gain bandwidth of 2.70 GHz, slew rate of 1816 V/µs, phase margin of 59.53º, power supply of the proposed operational amplifier is 1.4 V (rail-to-rail ±700 mV, and power consumption is 0.71 mW. This circuit specification has encountered the requirements of radio frequency application.

Two-stage exchange knee arthroplasty: does resistance of the infecting organism influence the outcome?

Science.gov (United States)

Kurd, Mark F; Ghanem, Elie; Steinbrecher, Jill; Parvizi, Javad

2010-08-01

Periprosthetic joint infection after TKA is a challenging complication. Two-stage exchange arthroplasty is the accepted standard of care, but reported failure rates are increasing. It has been suggested this is due to the increased prevalence of methicillin-resistant infections. We asked the following questions: (1) What is the reinfection rate after two-stage exchange arthroplasty? (2) Which risk factors predict failure? (3) Which variables are associated with acquiring a resistant organism periprosthetic joint infection? This was a case-control study of 102 patients with infected TKA who underwent a two-stage exchange arthroplasty. Ninety-six patients were followed for a minimum of 2 years (mean, 34.5 months; range, 24-90.1 months). Cases were defined as failures of two-stage exchange arthroplasty. Two-stage exchange arthroplasty was successful in controlling the infection in 70 patients (73%). Patients who failed two-stage exchange arthroplasty were 3.37 times more likely to have been originally infected with a methicillin-resistant organism. Older age, higher body mass index, and history of thyroid disease were predisposing factors to infection with a methicillin-resistant organism. Innovative interventions are needed to improve the effectiveness of two-stage exchange arthroplasty for TKA infection with a methicillin-resistant organism as current treatment protocols may not be adequate for control of these virulent pathogens. Level IV, prognostic study. See Guidelines for Authors for a complete description of levels of evidence.

Kinetics of two-stage fermentation process for the production of hydrogen

Energy Technology Data Exchange (ETDEWEB)

Nath, Kaushik [Department of Chemical Engineering, G.H. Patel College of Engineering and Technology, Vallabh Vidyanagar 388 120, Gujarat (India); Muthukumar, Manoj; Kumar, Anish; Das, Debabrata [Fermentation Technology Laboratory, Department of Biotechnology, Indian Institute of Technology, Kharagpur 721302 (India)

2008-02-15

Two-stage process described in the present work is a combination of dark and photofermentation in a sequential batch mode. In the first stage glucose is fermented to acetate, CO{sub 2} and H{sub 2} in an anaerobic dark fermentation by Enterobacter cloacae DM11. This is followed by a successive second stage where acetate is converted to H{sub 2} and CO{sub 2} in a photobioreactor by photosynthetic bacteria, Rhodobacter sphaeroides O.U. 001. The yield of hydrogen in the first stage was about 3.31molH{sub 2}(molglucose){sup -1} (approximately 82% of theoretical) and that in the second stage was about 1.5-1.72molH{sub 2}(molaceticacid){sup -1} (approximately 37-43% of theoretical). The overall yield of hydrogen in two-stage process considering glucose as preliminary substrate was found to be higher compared to a single stage process. Monod model, with incorporation of substrate inhibition term, has been used to determine the growth kinetic parameters for the first stage. The values of maximum specific growth rate ({mu} {sub max}) and K{sub s} (saturation constant) were 0.398h{sup -1} and 5.509gl{sup -1}, respectively, using glucose as substrate. The experimental substrate and biomass concentration profiles have good resemblance with those obtained by kinetic model predictions. A model based on logistic equation has been developed to describe the growth of R. sphaeroides O.U 001 in the second stage. Modified Gompertz equation was applied to estimate the hydrogen production potential, rate and lag phase time in a batch process for various initial concentration of glucose, based on the cumulative hydrogen production curves. Both the curve fitting and statistical analysis showed that the equation was suitable to describe the progress of cumulative hydrogen production. (author)

Two-stage energy storage equalization system for lithium-ion battery pack

Science.gov (United States)

Chen, W.; Yang, Z. X.; Dong, G. Q.; Li, Y. B.; He, Q. Y.

2017-11-01

How to raise the efficiency of energy storage and maximize storage capacity is a core problem in current energy storage management. For that, two-stage energy storage equalization system which contains two-stage equalization topology and control strategy based on a symmetric multi-winding transformer and DC-DC (direct current-direct current) converter is proposed with bidirectional active equalization theory, in order to realize the objectives of consistent lithium-ion battery packs voltages and cells voltages inside packs by using a method of the Range. Modeling analysis demonstrates that the voltage dispersion of lithium-ion battery packs and cells inside packs can be kept within 2 percent during charging and discharging. Equalization time was 0.5 ms, which shortened equalization time of 33.3 percent compared with DC-DC converter. Therefore, the proposed two-stage lithium-ion battery equalization system can achieve maximum storage capacity between lithium-ion battery packs and cells inside packs, meanwhile efficiency of energy storage is significantly improved.

Two-Stage Power Factor Corrected Power Supplies: The Low Component-Stress Approach

DEFF Research Database (Denmark)

Petersen, Lars; Andersen, Michael Andreas E.

2002-01-01

The discussion concerning the use of single-stage contra two-stage PFC solutions has been going on for the last decade and it continues. The purpose of this paper is to direct the focus back on how the power is processed and not so much as to the number of stages or the amount of power processed...

Bias due to two-stage residual-outcome regression analysis in genetic association studies.

Science.gov (United States)

Demissie, Serkalem; Cupples, L Adrienne

2011-11-01

Association studies of risk factors and complex diseases require careful assessment of potential confounding factors. Two-stage regression analysis, sometimes referred to as residual- or adjusted-outcome analysis, has been increasingly used in association studies of single nucleotide polymorphisms (SNPs) and quantitative traits. In this analysis, first, a residual-outcome is calculated from a regression of the outcome variable on covariates and then the relationship between the adjusted-outcome and the SNP is evaluated by a simple linear regression of the adjusted-outcome on the SNP. In this article, we examine the performance of this two-stage analysis as compared with multiple linear regression (MLR) analysis. Our findings show that when a SNP and a covariate are correlated, the two-stage approach results in biased genotypic effect and loss of power. Bias is always toward the null and increases with the squared-correlation between the SNP and the covariate (). For example, for , 0.1, and 0.5, two-stage analysis results in, respectively, 0, 10, and 50% attenuation in the SNP effect. As expected, MLR was always unbiased. Since individual SNPs often show little or no correlation with covariates, a two-stage analysis is expected to perform as well as MLR in many genetic studies; however, it produces considerably different results from MLR and may lead to incorrect conclusions when independent variables are highly correlated. While a useful alternative to MLR under , the two -stage approach has serious limitations. Its use as a simple substitute for MLR should be avoided. © 2011 Wiley Periodicals, Inc.

Robust Frequency-Domain Constrained Feedback Design via a Two-Stage Heuristic Approach.

Science.gov (United States)

Li, Xianwei; Gao, Huijun

2015-10-01

Based on a two-stage heuristic method, this paper is concerned with the design of robust feedback controllers with restricted frequency-domain specifications (RFDSs) for uncertain linear discrete-time systems. Polytopic uncertainties are assumed to enter all the system matrices, while RFDSs are motivated by the fact that practical design specifications are often described in restricted finite frequency ranges. Dilated multipliers are first introduced to relax the generalized Kalman-Yakubovich-Popov lemma for output feedback controller synthesis and robust performance analysis. Then a two-stage approach to output feedback controller synthesis is proposed: at the first stage, a robust full-information (FI) controller is designed, which is used to construct a required output feedback controller at the second stage. To improve the solvability of the synthesis method, heuristic iterative algorithms are further formulated for exploring the feedback gain and optimizing the initial FI controller at the individual stage. The effectiveness of the proposed design method is finally demonstrated by the application to active control of suspension systems.

Two-stage atlas subset selection in multi-atlas based image segmentation

Energy Technology Data Exchange (ETDEWEB)

Zhao, Tingting, E-mail: tingtingzhao@mednet.ucla.edu; Ruan, Dan, E-mail: druan@mednet.ucla.edu [The Department of Radiation Oncology, University of California, Los Angeles, California 90095 (United States)

2015-06-15

Purpose: Fast growing access to large databases and cloud stored data presents a unique opportunity for multi-atlas based image segmentation and also presents challenges in heterogeneous atlas quality and computation burden. This work aims to develop a novel two-stage method tailored to the special needs in the face of large atlas collection with varied quality, so that high-accuracy segmentation can be achieved with low computational cost. Methods: An atlas subset selection scheme is proposed to substitute a significant portion of the computationally expensive full-fledged registration in the conventional scheme with a low-cost alternative. More specifically, the authors introduce a two-stage atlas subset selection method. In the first stage, an augmented subset is obtained based on a low-cost registration configuration and a preliminary relevance metric; in the second stage, the subset is further narrowed down to a fusion set of desired size, based on full-fledged registration and a refined relevance metric. An inference model is developed to characterize the relationship between the preliminary and refined relevance metrics, and a proper augmented subset size is derived to ensure that the desired atlases survive the preliminary selection with high probability. Results: The performance of the proposed scheme has been assessed with cross validation based on two clinical datasets consisting of manually segmented prostate and brain magnetic resonance images, respectively. The proposed scheme demonstrates comparable end-to-end segmentation performance as the conventional single-stage selection method, but with significant computation reduction. Compared with the alternative computation reduction method, their scheme improves the mean and medium Dice similarity coefficient value from (0.74, 0.78) to (0.83, 0.85) and from (0.82, 0.84) to (0.95, 0.95) for prostate and corpus callosum segmentation, respectively, with statistical significance. Conclusions: The authors

Two-stage atlas subset selection in multi-atlas based image segmentation.

Science.gov (United States)

Zhao, Tingting; Ruan, Dan

2015-06-01

Fast growing access to large databases and cloud stored data presents a unique opportunity for multi-atlas based image segmentation and also presents challenges in heterogeneous atlas quality and computation burden. This work aims to develop a novel two-stage method tailored to the special needs in the face of large atlas collection with varied quality, so that high-accuracy segmentation can be achieved with low computational cost. An atlas subset selection scheme is proposed to substitute a significant portion of the computationally expensive full-fledged registration in the conventional scheme with a low-cost alternative. More specifically, the authors introduce a two-stage atlas subset selection method. In the first stage, an augmented subset is obtained based on a low-cost registration configuration and a preliminary relevance metric; in the second stage, the subset is further narrowed down to a fusion set of desired size, based on full-fledged registration and a refined relevance metric. An inference model is developed to characterize the relationship between the preliminary and refined relevance metrics, and a proper augmented subset size is derived to ensure that the desired atlases survive the preliminary selection with high probability. The performance of the proposed scheme has been assessed with cross validation based on two clinical datasets consisting of manually segmented prostate and brain magnetic resonance images, respectively. The proposed scheme demonstrates comparable end-to-end segmentation performance as the conventional single-stage selection method, but with significant computation reduction. Compared with the alternative computation reduction method, their scheme improves the mean and medium Dice similarity coefficient value from (0.74, 0.78) to (0.83, 0.85) and from (0.82, 0.84) to (0.95, 0.95) for prostate and corpus callosum segmentation, respectively, with statistical significance. The authors have developed a novel two-stage atlas

Two-stage atlas subset selection in multi-atlas based image segmentation

International Nuclear Information System (INIS)

Zhao, Tingting; Ruan, Dan

2015-01-01

Purpose: Fast growing access to large databases and cloud stored data presents a unique opportunity for multi-atlas based image segmentation and also presents challenges in heterogeneous atlas quality and computation burden. This work aims to develop a novel two-stage method tailored to the special needs in the face of large atlas collection with varied quality, so that high-accuracy segmentation can be achieved with low computational cost. Methods: An atlas subset selection scheme is proposed to substitute a significant portion of the computationally expensive full-fledged registration in the conventional scheme with a low-cost alternative. More specifically, the authors introduce a two-stage atlas subset selection method. In the first stage, an augmented subset is obtained based on a low-cost registration configuration and a preliminary relevance metric; in the second stage, the subset is further narrowed down to a fusion set of desired size, based on full-fledged registration and a refined relevance metric. An inference model is developed to characterize the relationship between the preliminary and refined relevance metrics, and a proper augmented subset size is derived to ensure that the desired atlases survive the preliminary selection with high probability. Results: The performance of the proposed scheme has been assessed with cross validation based on two clinical datasets consisting of manually segmented prostate and brain magnetic resonance images, respectively. The proposed scheme demonstrates comparable end-to-end segmentation performance as the conventional single-stage selection method, but with significant computation reduction. Compared with the alternative computation reduction method, their scheme improves the mean and medium Dice similarity coefficient value from (0.74, 0.78) to (0.83, 0.85) and from (0.82, 0.84) to (0.95, 0.95) for prostate and corpus callosum segmentation, respectively, with statistical significance. Conclusions: The authors

Experimental study on an innovative multifunction heat pipe type heat recovery two-stage sorption refrigeration system

International Nuclear Information System (INIS)

Li, T.X.; Wang, R.Z.; Wang, L.W.; Lu, Z.S.

2008-01-01

An innovative multifunction heat pipe type sorption refrigeration system is designed, in which a two-stage sorption thermodynamic cycle based on two heat recovery processes was employed to reduce the driving heat source temperature, and the composite sorbent of CaCl 2 and activated carbon was used to improve the mass and heat transfer performances. For this test unit, the heating, cooling and heat recovery processes between two reactive beds are performed by multifunction heat pipes. The aim of this paper is to investigate the cycled characteristics of two-stage sorption refrigeration system with heat recovery processes. The two sub-cycles of a two-stage cycle have different sorption platforms though the adsorption and desorption temperatures are equivalent. The experimental results showed that the pressure evolutions of two beds are nearly equivalent during the first stage, and desorption pressure during the second stage is large higher than that in the first stage while the desorption temperatures are same during the two operation stages. In comparison with conventional two-stage cycle, the two-stage cycle with heat recovery processes can reduce the heating load for desorber and cooling load for adsorber, the coefficient of performance (COP) has been improved more than 23% when both cycles have the same regeneration temperature of 103 deg. C and the cooling water temperature of 30 deg. C. The advanced two-stage cycle provides an effective method for application of sorption refrigeration technology under the condition of low-grade temperature heat source or utilization of renewable energy

An unit cost adjusting heuristic algorithm for the integrated planning and scheduling of a two-stage supply chain

Directory of Open Access Journals (Sweden)

Jianhua Wang

2014-10-01

Full Text Available Purpose: The stable relationship of one-supplier-one-customer is replaced by a dynamic relationship of multi-supplier-multi-customer in current market gradually, and efficient scheduling techniques are important tools of the dynamic supply chain relationship establishing process. This paper studies the optimization of the integrated planning and scheduling problem of a two-stage supply chain with multiple manufacturers and multiple retailers to obtain a minimum supply chain operating cost, whose manufacturers have different production capacities, holding and producing cost rates, transportation costs to retailers.Design/methodology/approach: As a complex task allocation and scheduling problem, this paper sets up an INLP model for it and designs a Unit Cost Adjusting (UCA heuristic algorithm that adjust the suppliers’ supplying quantity according to their unit costs step by step to solve the model.Findings: Relying on the contrasting analysis between the UCA and the Lingo solvers for optimizing many numerical experiments, results show that the INLP model and the UCA algorithm can obtain its near optimal solution of the two-stage supply chain’s planning and scheduling problem within very short CPU time.Research limitations/implications: The proposed UCA heuristic can easily help managers to optimizing the two-stage supply chain scheduling problems which doesn’t include the delivery time and batch of orders. For two-stage supply chains are the most common form of actual commercial relationships, so to make some modification and study on the UCA heuristic should be able to optimize the integrated planning and scheduling problems of a supply chain with more reality constraints.Originality/value: This research proposes an innovative UCA heuristic for optimizing the integrated planning and scheduling problem of two-stage supply chains with the constraints of suppliers’ production capacity and the orders’ delivering time, and has a great

One-Stage and Two-Stage Schemes of High Performance Synchronous PWM with Smooth Pulses-Ratio Changing

DEFF Research Database (Denmark)

Oleschuk, V.; Blaabjerg, Frede

2002-01-01

This paper presents detailed description of one-stage and two-stage schemes of a novel method of synchronous, pulsewidth modulation (PWM) for voltage source inverters for ac drive application. The proposed control functions provide accurate realization of different versions of voltage space vector...... modulation with synchronization of the voltage waveform of the inverter and with smooth pulse-ratio changing. Voltage spectra do not contain even harmonic and sub-harmonics (combined harmonics) during the whole control range including the zone of overmodulation. Examples of determination of the basic control...

A novel wavelet neural network based pathological stage detection technique for an oral precancerous condition

Science.gov (United States)

Paul, R R; Mukherjee, A; Dutta, P K; Banerjee, S; Pal, M; Chatterjee, J; Chaudhuri, K; Mukkerjee, K

2005-01-01

Aim: To describe a novel neural network based oral precancer (oral submucous fibrosis; OSF) stage detection method. Method: The wavelet coefficients of transmission electron microscopy images of collagen fibres from normal oral submucosa and OSF tissues were used to choose the feature vector which, in turn, was used to train the artificial neural network. Results: The trained network was able to classify normal and oral precancer stages (less advanced and advanced) after obtaining the image as an input. Conclusions: The results obtained from this proposed technique were promising and suggest that with further optimisation this method could be used to detect and stage OSF, and could be adapted for other conditions. PMID:16126873

One-stage exchange with antibacterial hydrogel coated implants provides similar results to two-stage revision, without the coating, for the treatment of peri-prosthetic infection.

Science.gov (United States)

Capuano, Nicola; Logoluso, Nicola; Gallazzi, Enrico; Drago, Lorenzo; Romanò, Carlo Luca

2018-03-16

Aim of this study was to verify the hypothesis that a one-stage exchange procedure, performed with an antibiotic-loaded, fast-resorbable hydrogel coating, provides similar infection recurrence rate than a two-stage procedure without the coating, in patients affected by peri-prosthetic joint infection (PJI). In this two-center case-control, study, 22 patients, treated with a one-stage procedure, using implants coated with an antibiotic-loaded hydrogel [defensive antibacterial coating (DAC)], were compared with 22 retrospective matched controls, treated with a two-stage revision procedure, without the coating. At a mean follow-up of 29.3 ± 5.0 months, two patients (9.1%) in the DAC group showed an infection recurrence, compared to three patients (13.6%) in the two-stage group. Clinical scores were similar between groups, while average hospital stay and antibiotic treatment duration were significantly reduced after one-stage, compared to two-stage (18.9 ± 2.9 versus 35.8 ± 3.4 and 23.5 ± 3.3 versus 53.7 ± 5.6 days, respectively). Although in a relatively limited series of patients, our data shows similar infection recurrence rate after one-stage exchange with DAC-coated implants, compared to two-stage revision without coating, with reduced overall hospitalization time and antibiotic treatment duration. These findings warrant further studies in the possible applications of antibacterial coating technologies to treat implant-related infections. III.

Lower-Order Compensation Chain Threshold-Reduction Technique for Multi-Stage Voltage Multipliers.

Science.gov (United States)

Dell' Anna, Francesco; Dong, Tao; Li, Ping; Wen, Yumei; Azadmehr, Mehdi; Casu, Mario; Berg, Yngvar

2018-04-17

This paper presents a novel threshold-compensation technique for multi-stage voltage multipliers employed in low power applications such as passive and autonomous wireless sensing nodes (WSNs) powered by energy harvesters. The proposed threshold-reduction technique enables a topological design methodology which, through an optimum control of the trade-off among transistor conductivity and leakage losses, is aimed at maximizing the voltage conversion efficiency (VCE) for a given ac input signal and physical chip area occupation. The conducted simulations positively assert the validity of the proposed design methodology, emphasizing the exploitable design space yielded by the transistor connection scheme in the voltage multiplier chain. An experimental validation and comparison of threshold-compensation techniques was performed, adopting 2N5247 N-channel junction field effect transistors (JFETs) for the realization of the voltage multiplier prototypes. The attained measurements clearly support the effectiveness of the proposed threshold-reduction approach, which can significantly reduce the chip area occupation for a given target output performance and ac input signal.

Two-stage multilevel en bloc spondylectomy with resection and replacement of the aorta.

Science.gov (United States)

Gösling, Thomas; Pichlmaier, Maximilian A; Länger, Florian; Krettek, Christian; Hüfner, Tobias

2013-05-01

We report a case of multilevel spondylectomy in which resection and replacement of the adjacent aorta were done. Although spondylectomy is nowadays an established technique, no report on a combined aortic resection and replacement has been reported so far. The case of a 43-year-old man with a primary chondrosarcoma of the thoracic spine is presented. The local pathology necessitated resection of the aorta. We did a two-stage procedure with resection and replacement of the aorta using a heart-lung machine followed by secondary tumor resection and spinal reconstruction. The procedure was successful. A tumor-free margin was achieved. The patient is free of disease 48 months after surgery. En bloc spondylectomy in combination with aortic resection is feasible and might expand the possibility of producing tumor-free margins in special situations.

A two-phase inspection model for a single component system with three-stage degradation

International Nuclear Information System (INIS)

Wang, Huiying; Wang, Wenbin; Peng, Rui

2017-01-01

This paper presents a two-phase inspection schedule and an age-based replacement policy for a single plant item contingent on a three-stage degradation process. The two phase inspection schedule can be observed in practice. The three stages are defined as the normal working stage, low-grade defective stage and critical defective stage. When an inspection detects that an item is in the low-grade defective stage, we may delay the preventive replacement action if the time to the age-based replacement is less than or equal to a threshold level. However, if it is above this threshold level, the item will be replaced immediately. If the item is found in the critical defective stage, it is replaced immediately. A hybrid bee colony algorithm is developed to find the optimal solution for the proposed model which has multiple decision variables. A numerical example is conducted to show the efficiency of this algorithm, and simulations are conducted to verify the correctness of the model. - Highlights: • A two-phase inspection model is studied. • The failure process has three stages. • The delayed replacement is considered.

Experimental Results of the First Two Stages of an Advanced Transonic Core Compressor Under Isolated and Multi-Stage Conditions

Science.gov (United States)

Prahst, Patricia S.; Kulkarni, Sameer; Sohn, Ki H.

2015-01-01

NASA's Environmentally Responsible Aviation (ERA) Program calls for investigation of the technology barriers associated with improved fuel efficiency of large gas turbine engines. Under ERA the task for a High Pressure Ratio Core Technology program calls for a higher overall pressure ratio of 60 to 70. This mean that the HPC would have to almost double in pressure ratio and keep its high level of efficiency. The challenge is how to match the corrected mass flow rate of the front two supersonic high reaction and high corrected tip speed stages with a total pressure ratio of 3.5. NASA and GE teamed to address this challenge by using the initial geometry of an advanced GE compressor design to meet the requirements of the first 2 stages of the very high pressure ratio core compressor. The rig was configured to run as a 2 stage machine, with Strut and IGV, Rotor 1 and Stator 1 run as independent tests which were then followed by adding the second stage. The goal is to fully understand the stage performances under isolated and multi-stage conditions and fully understand any differences and provide a detailed aerodynamic data set for CFD validation. Full use was made of steady and unsteady measurement methods to isolate fluid dynamics loss source mechanisms due to interaction and endwalls. The paper will present the description of the compressor test article, its predicted performance and operability, and the experimental results for both the single stage and two stage configurations. We focus the detailed measurements on 97 and 100 of design speed at 3 vane setting angles.

Efficiency of primary care in rural Burkina Faso. A two-stage DEA analysis.

Science.gov (United States)

Marschall, Paul; Flessa, Steffen

2011-07-20

Providing health care services in Africa is hampered by severe scarcity of personnel, medical supplies and financial funds. Consequently, managers of health care institutions are called to measure and improve the efficiency of their facilities in order to provide the best possible services with their resources. However, very little is known about the efficiency of health care facilities in Africa and instruments of performance measurement are hardly applied in this context. This study determines the relative efficiency of primary care facilities in Nouna, a rural health district in Burkina Faso. Furthermore, it analyses the factors influencing the efficiency of these institutions. We apply a two-stage Data Envelopment Analysis (DEA) based on data from a comprehensive provider and household information system. In the first stage, the relative efficiency of each institution is calculated by a traditional DEA model. In the second stage, we identify the reasons for being inefficient by regression technique. The DEA projections suggest that inefficiency is mainly a result of poor utilization of health care facilities as they were either too big or the demand was too low. Regression results showed that distance is an important factor influencing the efficiency of a health care institution Compared to the findings of existing one-stage DEA analyses of health facilities in Africa, the share of relatively efficient units is slightly higher. The difference might be explained by a rather homogenous structure of the primary care facilities in the Burkina Faso sample. The study also indicates that improving the accessibility of primary care facilities will have a major impact on the efficiency of these institutions. Thus, health decision-makers are called to overcome the demand-side barriers in accessing health care.

Composite likelihood and two-stage estimation in family studies

DEFF Research Database (Denmark)

Andersen, Elisabeth Anne Wreford

2004-01-01

In this paper register based family studies provide the motivation for linking a two-stage estimation procedure in copula models for multivariate failure time data with a composite likelihood approach. The asymptotic properties of the estimators in both parametric and semi-parametric models are d...

Compressed gas combined single- and two-stage light-gas gun

Science.gov (United States)

Lamberson, L. E.; Boettcher, P. A.

2018-02-01

With more than 1 trillion artificial objects smaller than 1 μm in low and geostationary Earth orbit, space assets are subject to the constant threat of space debris impact. These collisions occur at hypervelocity or speeds greater than 3 km/s. In order to characterize material behavior under this extreme event as well as study next-generation materials for space exploration, this paper presents a unique two-stage light-gas gun capable of replicating hypervelocity impacts. While a limited number of these types of facilities exist, they typically are extremely large and can be costly and dangerous to operate. The design presented in this paper is novel in two distinct ways. First, it does not use a form of combustion in the first stage. The projectile is accelerated from a pressure differential using air and inert gases (or purely inert gases), firing a projectile in a nominal range of 1-4 km/s. Second, the design is modular in that the first stage sits on a track sled and can be pulled back and used in itself to study lower speed impacts without any further modifications, with the first stage piston as the impactor. The modularity of the instrument allows the ability to investigate three orders of magnitude of impact velocities or between 101 and 103 m/s in a single, relatively small, cost effective instrument.

Microgravimetric Studies of Selenium Electrodeposition Onto Different Substrates

Directory of Open Access Journals (Sweden)

Kowalik R.

2014-10-01

Full Text Available The mechanism of selenium electrodeposition from sulfuric acid solution on different substrates was studied with the electrochemical techniques. The cyclic voltammetry was combined with the quartz crystal microbalance technique to analyze selenium deposition process. The electrochemical reduction of selenous acid on gold, silver and copper electrodes was investigated. It was found that reduction of selenous acid is a very complex process and it strongly depends from the applied substrate. The voltammetric measurements indicate the range of potentials in which the process of reduction of selenous acids on the applied substrate is possible. Additionally, the microgravimetric data confirm the deposition of selenium and they reveal the mechanism of the deposition process.

The Two-stage Constrained Equal Awards and Losses Rules for Multi-Issue Allocation Situation

NARCIS (Netherlands)

Lorenzo-Freire, S.; Casas-Mendez, B.; Hendrickx, R.L.P.

2005-01-01

This paper considers two-stage solutions for multi-issue allocation situations.Characterisations are provided for the two-stage constrained equal awards and constrained equal losses rules, based on the properties of composition and path independence.

Design and construction of a two-stage centrifugal pump | Nordiana ...

African Journals Online (AJOL)

Centrifugal pumps are widely used in moving liquids from one location to another in homes, offices and industries. Due to the ever increasing demand for centrifugal pumps it became necessary to design and construction of a two-stage centrifugal pump. The pump consisted of an electric motor, a shaft, two rotating impellers ...

Two applications of airtightness control techniques on big assemblies

CERN Document Server

Devallan, C; Marcellin, J

1973-01-01

Deals with two airtightness control techniques respectively applied on intersecting storage rings (ISR) at CERN in Geneva and on a liquid methane storage tank. These two big assemblies called for two different control techniques which use helium and ammonia respectively as tracer gas. Existing practical leakage detection techniques to meet industrial needs are discussed at the end of the article. (2 refs).

Time stamp technique using a nuclear emulsion multi-stage shifter for gamma-ray telescope

International Nuclear Information System (INIS)

Takahashi, Satoru; Aoki, Shigeki; Rokujo, Hiroki; Hamada, Kaname; Komatsu, Masahiro; Morishima, Kunihiro; Nakamura, Mitsuhiro; Nakano, Toshiyuki; Niwa, Kimio; Sato, Osamu; Yoshioka, Teppei; Kodama, Koichi

2010-01-01

Nuclear emulsion has a potential use as a gamma-ray telescope with high angular resolution. For this application it is necessary to know the time when each track was recorded in the emulsion. In previous experiments using nuclear emulsion, various efforts were used to associate time to nuclear emulsion tracks and to improve the time resolution. Using a high speed readout system for nuclear emulsion together with a clock-based multi-stage emulsion shifter, we invented a technique to give a time-stamp to emulsion tracks and greatly improve the time resolution. A test experiment with a 2-stage shifter was used to demonstrate the principle of multi-stage shifting, and we achieved a time resolution 1.5 s for 12.1 h (about 1 part in 29 000) with the time stamp reliability 97% and the time stamp efficiency 98%. This multi-stage shifter can achieve the time resolution required for a gamma-ray telescope and can also be applied to another cosmic ray observations and accelerator experiments using nuclear emulsion.

A Two-stage Improvement Method for Robot Based 3D Surface Scanning

Science.gov (United States)

He, F. B.; Liang, Y. D.; Wang, R. F.; Lin, Y. S.

2018-03-01

As known that the surface of unknown object was difficult to measure or recognize precisely, hence the 3D laser scanning technology was introduced and used properly in surface reconstruction. Usually, the surface scanning speed was slower and the scanning quality would be better, while the speed was faster and the quality would be worse. In this case, the paper presented a new two-stage scanning method in order to pursuit the quality of surface scanning in a faster speed. The first stage was rough scanning to get general point cloud data of object’s surface, and then the second stage was specific scanning to repair missing regions which were determined by chord length discrete method. Meanwhile, a system containing a robotic manipulator and a handy scanner was also developed to implement the two-stage scanning method, and relevant paths were planned according to minimum enclosing ball and regional coverage theories.

Surgical reconstruction of pressure ulcer defects: a single- or two-stage procedure?

LENUS (Irish Health Repository)

Laing, Tereze A

2012-02-01

BACKGROUND: The surgical management of pressure ulcers traditionally involved staged procedures, with initial debridement of necrotic or infected material followed by reconstruction at a later date when the wound was deemed viable and free of gross infection. However, over the past decade, it has been suggested that a single-stage procedure, combining initial debridement and definitive reconstruction, may provide advantages over staged surgery. We present our experience with the staged approach and review the current evidence for both methods. SUBJECTS AND SETTINGS: : We reviewed medical records of all patients referred to our service for pressure ulcer management between October 2001 and October 2007. The National Rehabilitation Hospital is the national center in Ireland for primary rehabilitation of adults and children suffering from spinal and brain injury, serving patients locally and from around the country. METHODS: All subjects who were managed surgically underwent a 2-stage procedure, with initial debridement and subsequent reconstruction. The main outcome measures were length of hospital stay, postoperative morbidity and mortality, and time to complete ulcer healing. RESULTS: Forty-one of 108 patients with 58 pressure ulcers were managed surgically. All patients underwent initial surgical debridement and 20 patients underwent subsequent pressure ulcer reconstruction. Postreconstructive complications occurred in 5 patients (20%). The mean time to complete ulcer healing was 17.4 weeks. Partial flap necrosis occurred in 3 patients, but there were no episodes of flap failure. CONCLUSIONS: We achieved favorable results with a 2-stage reconstruction technique and suggest that the paucity of evidence related to single-stage procedures does not support a change in surgical management.

A high-power two stage traveling-wave tube amplifier

International Nuclear Information System (INIS)

Shiffler, D.; Nation, J.A.; Schachter, L.; Ivers, J.D.; Kerslick, G.S.

1991-01-01

Results are presented on the development of a two stage high-efficiency, high-power 8.76-GHz traveling-wave tube amplifier. The work presented augments previously reported data on a single stage amplifier and presents new data on the operational characteristics of two identical amplifiers operated in series and separated from each other by a sever. Peak powers of 410 MW have been obtained over the complete pulse duration of the device, with a conversion efficiency from the electron beam to microwave energy of 45%. In all operating conditions the severed amplifier showed a ''sideband''-like structure in the frequency spectrum of the microwave radiation. A similar structure was apparent at output powers in excess of 70 MW in the single stage device. The frequencies of the ''sidebands'' are not symmetric with respect to the center frequency. The maximum, single frequency, average output power was 210 MW corresponding to an amplifier efficiency of 24%. Simulation data is also presented that indicates that the short amplifiers used in this work exhibit significant differences in behavior from conventional low-power amplifiers. These include finite length effects on the gain characteristics, which may account for the observed narrow bandwidth of the amplifiers and for the appearance of the sidebands. It is also found that the bunching length for the beam may be a significant fraction of the total amplifier length

Biogas production of Chicken Manure by Two-stage fermentation process

Science.gov (United States)

Liu, Xin Yuan; Wang, Jing Jing; Nie, Jia Min; Wu, Nan; Yang, Fang; Yang, Ren Jie

2018-06-01

This paper performs a batch experiment for pre-acidification treatment and methane production from chicken manure by the two-stage anaerobic fermentation process. Results shows that the acetate was the main component in volatile fatty acids produced at the end of pre-acidification stage, accounting for 68% of the total amount. The daily biogas production experienced three peak period in methane production stage, and the methane content reached 60% in the second period and then slowly reduced to 44.5% in the third period. The cumulative methane production was fitted by modified Gompertz equation, and the kinetic parameters of the methane production potential, the maximum methane production rate and lag phase time were 345.2 ml, 0.948 ml/h and 343.5 h, respectively. The methane yield of 183 ml-CH4/g-VSremoved during the methane production stage and VS removal efficiency of 52.7% for the whole fermentation process were achieved.

Two-stage high frequency pulse tube refrigerator with base temperature below 10 K

Science.gov (United States)

Chen, Liubiao; Wu, Xianlin; Liu, Sixue; Zhu, Xiaoshuang; Pan, Changzhao; Guo, Jia; Zhou, Yuan; Wang, Junjie

2017-12-01

This paper introduces our recent experimental results of pulse tube refrigerator driven by linear compressor. The working frequency is 23-30 Hz, which is much higher than the G-M type cooler (the developed cryocooler will be called high frequency pulse tube refrigerator in this paper). To achieve a temperature below 10 K, two types of two-stage configuration, gas coupled and thermal coupled, have been designed, built and tested. At present, both types can achieve a no-load temperature below 10 K by using only one compressor. As to gas-coupled HPTR, the second stage can achieve a cooling power of 16 mW/10K when the first stage applied a 400 mW heat load at 60 K with a total input power of 400 W. As to thermal-coupled HPTR, the designed cooling power of the first stage is 10W/80K, and then the temperature of the second stage can get a temperature below 10 K with a total input power of 300 W. In the current preliminary experiment, liquid nitrogen is used to replace the first coaxial configuration as the precooling stage, and a no-load temperature 9.6 K can be achieved with a stainless steel mesh regenerator. Using Er3Ni sphere with a diameter about 50-60 micron, the simulation results show it is possible to achieve a temperature below 8 K. The configuration, the phase shifters and the regenerative materials of the developed two types of two-stage high frequency pulse tube refrigerator will be discussed, and some typical experimental results and considerations for achieving a better performance will also be presented in this paper.

Multiple heavy metals extraction and recovery from hazardous electroplating sludge waste via ultrasonically enhanced two-stage acid leaching.

Science.gov (United States)

Li, Chuncheng; Xie, Fengchun; Ma, Yang; Cai, Tingting; Li, Haiying; Huang, Zhiyuan; Yuan, Gaoqing

2010-06-15

An ultrasonically enhanced two-stage acid leaching process on extracting and recovering multiple heavy metals from actual electroplating sludge was studied in lab tests. It provided an effective technique for separation of valuable metals (Cu, Ni and Zn) from less valuable metals (Fe and Cr) in electroplating sludge. The efficiency of the process had been measured with the leaching efficiencies and recovery rates of the metals. Enhanced by ultrasonic power, the first-stage acid leaching demonstrated leaching rates of 96.72%, 97.77%, 98.00%, 53.03%, and 0.44% for Cu, Ni, Zn, Cr, and Fe respectively, effectively separated half of Cr and almost all of Fe from mixed metals. The subsequent second-stage leaching achieved leaching rates of 75.03%, 81.05%, 81.39%, 1.02%, and 0% for Cu, Ni, Zn, Cr, and Fe that further separated Cu, Ni, and Zn from mixed metals. With the stabilized two-stage ultrasonically enhanced leaching, the resulting over all recovery rates of Cu, Ni, Zn, Cr and Fe from electroplating sludge could be achieved at 97.42%, 98.46%, 98.63%, 98.32% and 100% respectively, with Cr and Fe in solids and the rest of the metals in an aqueous solution discharged from the leaching system. The process performance parameters studied were pH, ultrasonic power, and contact time. The results were also confirmed in an industrial pilot-scale test, and same high metal recoveries were performed. Copyright 2010 Elsevier B.V. All rights reserved.

A COMPARISON OF TWO FUZZY CLUSTERING TECHNIQUES

Directory of Open Access Journals (Sweden)

Samarjit Das

2013-10-01

Full Text Available - In fuzzy clustering, unlike hard clustering, depending on the membership value, a single object may belong exactly to one cluster or partially to more than one cluster. Out of a number of fuzzy clustering techniques Bezdek’s Fuzzy C-Means and GustafsonKessel clustering techniques are well known where Euclidian distance and Mahalanobis distance are used respectively as a measure of similarity. We have applied these two fuzzy clustering techniques on a dataset of individual differences consisting of fifty feature vectors of dimension (feature three. Based on some validity measures we have tried to see the performances of these two clustering techniques from three different aspects- first, by initializing the membership values of the feature vectors considering the values of the three features separately one at a time, secondly, by changing the number of the predefined clusters and thirdly, by changing the size of the dataset.

A comparison of a new centrifuge sugar flotation technique with the agar method for the extraction of immature Culicoides (Diptera: Ceratopogonidae) life stages from salt marsh soils.

Science.gov (United States)

Two sampling techniques, agar extraction (AE) and centrifuge sugar flotation extraction (CSFE) were compared to determine their relative efficacy to recover immature stages of Culicoides spp from salt marsh substrates. Three types of samples (seeded with known numbers of larvae, homogenized field s...

The global stability of a delayed predator-prey system with two stage-structure

International Nuclear Information System (INIS)

Wang Fengyan; Pang Guoping

2009-01-01

Based on the classical delayed stage-structured model and Lotka-Volterra predator-prey model, we introduce and study a delayed predator-prey system, where prey and predator have two stages, an immature stage and a mature stage. The time delays are the time lengths between the immature's birth and maturity of prey and predator species. Results on global asymptotic stability of nonnegative equilibria of the delay system are given, which generalize and suggest that good continuity exists between the predator-prey system and its corresponding stage-structured system.

Experimental and numerical studies on two-stage combustion of biomass

Energy Technology Data Exchange (ETDEWEB)

Houshfar, Eshan

2012-07-01

In this thesis, two-stage combustion of biomass was experimentally/numerically investigated in a multifuel reactor. The following emissions issues have been the main focus of the work: 1- NOx and N2O 2- Unburnt species (CO and CxHy) 3- Corrosion related emissions.The study had a focus on two-stage combustion in order to reduce pollutant emissions (primarily NOx emissions). It is well known that pollutant emissions are very dependent on the process conditions such as temperature, reactant concentrations and residence times. On the other hand, emissions are also dependent on the fuel properties (moisture content, volatiles, alkali content, etc.). A detailed study of the important parameters with suitable biomass fuels in order to optimize the various process conditions was performed. Different experimental studies were carried out on biomass fuels in order to study the effect of fuel properties and combustion parameters on pollutant emissions. Process conditions typical for biomass combustion processes were studied. Advanced experimental equipment was used in these studies. The experiments showed the effects of staged air combustion, compared to non-staged combustion, on the emission levels clearly. A NOx reduction of up to 85% was reached with staged air combustion using demolition wood as fuel. An optimum primary excess air ratio of 0.8-0.95 was found as a minimizing parameter for the NOx emissions for staged air combustion. Air staging had, however, a negative effect on N2O emissions. Even though the trends showed a very small reduction in the NOx level as temperature increased for non-staged combustion, the effect of temperature was not significant for NOx and CxHy, neither in staged air combustion or non-staged combustion, while it had a great influence on the N2O and CO emissions, with decreasing levels with increasing temperature. Furthermore, flue gas recirculation (FGR) was used in combination with staged combustion to obtain an enhanced NOx reduction. The

Lower-Order Compensation Chain Threshold-Reduction Technique for Multi-Stage Voltage Multipliers

Directory of Open Access Journals (Sweden)

Francesco Dell’ Anna

2018-04-01

Full Text Available This paper presents a novel threshold-compensation technique for multi-stage voltage multipliers employed in low power applications such as passive and autonomous wireless sensing nodes (WSNs powered by energy harvesters. The proposed threshold-reduction technique enables a topological design methodology which, through an optimum control of the trade-off among transistor conductivity and leakage losses, is aimed at maximizing the voltage conversion efficiency (VCE for a given ac input signal and physical chip area occupation. The conducted simulations positively assert the validity of the proposed design methodology, emphasizing the exploitable design space yielded by the transistor connection scheme in the voltage multiplier chain. An experimental validation and comparison of threshold-compensation techniques was performed, adopting 2N5247 N-channel junction field effect transistors (JFETs for the realization of the voltage multiplier prototypes. The attained measurements clearly support the effectiveness of the proposed threshold-reduction approach, which can significantly reduce the chip area occupation for a given target output performance and ac input signal.

The contemporary role of 1 vs. 2-stage repair for proximal hypospadias.

Science.gov (United States)

Dason, Shawn; Wong, Nathan; Braga, Luis H

2014-12-01

This review discusses the most commonly employed techniques in the repair of proximal hypospadias, highlighting the advantages and disadvantages of single versus staged surgical techniques. Hypospadias can have a spectrum of severity with a urethral meatus ranging from the perineum to the glans. Associated abnormalities are commonly found with proximal hypospadias and encompass a large spectrum, including ventral curvature (VC) up to 50 degrees or more, ventral skin deficiency, a flattened glans, penile torsion and penoscrotal transposition. Our contemporary understanding of hypospadiology is comprised of a foundation built by experts who have described a number of techniques and their outcomes, combined with survey data detailing practice patterns. The two largest components of hypospadias repair include repair of VC and urethroplasty. VC greater than 20 degrees is considered clinically relevant to warrant surgical correction. To repair VC, the penis is first degloved-a procedure that may reduce or remove curvature by itself in some cases. Residual curvature is then repaired with dorsal plication techniques, transection of the urethral plate, and/or ventral lengthening techniques. Urethroplasty takes the form of 1- or 2-stage repairs. One-stage options include the tubularized incised urethroplasty (TIP) or various graft or flap-based techniques. Two-stage options also include grafts or flaps, including oral mucosal and preputial skin grafting. One stage repairs are an attractive option in that they may reduce cost, hospital stay, anesthetic risks, and time to the final result. The downside is that these repairs require mastery of multiple techniques may be more complex, and-depending on technique-have higher complication rates. Two-stage repairs are preferred by the majority of surveyed hypospadiologists. The 2-stage repair is versatile and has satisfactory outcomes, but necessitates a second procedure. Given the lack of clear high-quality evidence supporting the

Adjuvant therapy in stage I and stage II epithelial ovarian cancer. Results of two prospective randomized trials

International Nuclear Information System (INIS)

Young, R.C.; Walton, L.A.; Ellenberg, S.S.; Homesley, H.D.; Wilbanks, G.D.; Decker, D.G.; Miller, A.; Park, R.; Major, F. Jr.

1990-01-01

About a third of patients with ovarian cancer present with localized disease; despite surgical resection, up to half the tumors recur. Since it has not been established whether adjuvant treatment can benefit such patients, we conducted two prospective, randomized national cooperative trials of adjuvant therapy in patients with localized ovarian carcinoma. All patients underwent surgical resection plus comprehensive staging and, 18 months later, surgical re-exploration. In the first trial, 81 patients with well-differentiated or moderately well differentiated cancers confined to the ovaries (Stages Iai and Ibi) were assigned to receive either no chemotherapy or melphalan (0.2 mg per kilogram of body weight per day for five days, repeated every four to six weeks for up to 12 cycles). After a median follow-up of more than six years, there were no significant differences between the patients given no chemotherapy and those treated with melphalan with respect to either five-year disease-free survival or overall survival. In the second trial, 141 patients with poorly differentiated Stage I tumors or with cancer outside the ovaries but limited to the pelvis (Stage II) were randomly assigned to treatment with either melphalan (in the same regimen as above) or a single intraperitoneal dose of 32P (15 mCi) at the time of surgery. In this trial (median follow-up, greater than 6 years) the outcomes for the two treatment groups were similar with respect to five-year disease-free survival (80 percent in both groups) and overall survival (81 percent with melphalan vs. 78 percent with 32P; P = 0.48). We conclude that in patients with localized ovarian cancer, comprehensive staging at the time of surgical resection can serve to identify those patients (as defined by the first trial) who can be followed without adjuvant chemotherapy

Sorption mechanisms of selenium species (selenite and selenate) on copper-based minerals; Mecanismes de sorption des especes du selenium (selenite et seleniate) sur des mineraux a base de cuivre

Energy Technology Data Exchange (ETDEWEB)

Devoy, J

2001-09-01

The sorption of radionuclides on the surface of minerals represents a process capable to delay the migration of the elements from a spent fuel deep repository towards the biosphere. In the framework of a deep underground repository, an engineered clay barrier has a high trapping capacity for cationic radio-elements, in particular because of the negative charge of clay surfaces. However, anionic radioelements like selenium species, would be only weakly retained by chemical processes. In order to optimize the trapping capacity of a clay barrier with respect to anionic species, prospective studies are carried out in order to find and evaluate some minerals with specific chemical trapping functions. Among radionuclides, the case of selenium has to be considered because its isotope {sup 79}Se is present in radioactive wastes and has a half life time of 6.5 10{sup 4} years. It is also judicious to find a mineral capable of trapping simultaneously several anionic radio-elements. Copper oxides and sulfides (Cu{sub 2}O, CuO, Cu{sub 2}S, CuS, CuFeS{sub 2} and Cu{sub 5}FeS{sub 4}) are good adsorbents with respect to selenium species (selenite and selenate). These minerals, with their selenium retention properties, could be used also for the decontamination of soils and waters or to process industrial effluents. The sorption mechanisms have been studied in details for copper oxides (Cu{sub 2}O and CuO) with respect to selenite and selenate. Chalcomenite precipitates in acid pH conditions when selenite is added to a Cu{sub 2}O and CuO suspension. Selenate, in contact with cuprite (Cu{sub 2}O) leads also to a selenium-based precipitate in acid pH environment. For higher pH values, selenite and selenate are adsorbed on copper oxides (Cu{sub 2}O and CuO) and lead to internal and external sphere complexes, respectively. In the case of a selenite/cuprite mixture in basic pH environment and at the equilibrium, a chemical reaction occurs between the oxidation product of cuprite, Cu

Target tracking system based on preliminary and precise two-stage compound cameras

Science.gov (United States)

Shen, Yiyan; Hu, Ruolan; She, Jun; Luo, Yiming; Zhou, Jie

2018-02-01

Early detection of goals and high-precision of target tracking is two important performance indicators which need to be balanced in actual target search tracking system. This paper proposed a target tracking system with preliminary and precise two - stage compound. This system using a large field of view to achieve the target search. After the target was searched and confirmed, switch into a small field of view for two field of view target tracking. In this system, an appropriate filed switching strategy is the key to achieve tracking. At the same time, two groups PID parameters are add into the system to reduce tracking error. This combination way with preliminary and precise two-stage compound can extend the scope of the target and improve the target tracking accuracy and this method has practical value.

Divergent methylation pattern in adult stage between two forms of Tetranychus urticae (Acari: Tetranychidae).

Science.gov (United States)

Yang, Si-Xia; Guo, Chao; Zhao, Xiu-Ting; Sun, Jing-Tao; Hong, Xiao-Yue

2017-02-19

The two-spotted spider mite, Tetranychus urticae Koch has two forms: green form and red form. Understanding the molecular basis of how these two forms established without divergent genetic background is an intriguing area. As a well-known epigenetic process, DNA methylation has particularly important roles in gene regulation and developmental variation across diverse organisms that do not alter genetic background. Here, to investigate whether DNA methylation could be associated with different phenotypic consequences in the two forms of T. urticae, we surveyed the genome-wide cytosine methylation status and expression level of DNA methyltransferase 3 (Tudnmt3) throughout their entire life cycle. Methylation-sensitive amplification polymorphism (MSAP) analyses of 585 loci revealed variable methylation patterns in the different developmental stages. In particular, principal coordinates analysis (PCoA) indicates a significant epigenetic differentiation between female adults of the two forms. The gene expression of Tudnmt3 was detected in all examined developmental stages, which was significantly different in the adult stage of the two forms. Together, our results reveal the epigenetic distance between the two forms of T. urticae, suggesting that DNA methylation might be implicated in different developmental demands, and contribute to different phenotypes in the adult stage of these two forms. © 2017 Institute of Zoology, Chinese Academy of Sciences.

A novel sensor for two-degree-of-freedom motion measurement of linear nanopositioning stage using knife edge displacement sensing technique

Science.gov (United States)

Zolfaghari, Abolfazl; Jeon, Seongkyul; Stepanick, Christopher K.; Lee, ChaBum

2017-06-01

This paper presents a novel method for measuring two-degree-of-freedom (DOF) motion of flexure-based nanopositioning systems based on optical knife-edge sensing (OKES) technology, which utilizes the interference of two superimposed waves: a geometrical wave from the primary source of light and a boundary diffraction wave from the secondary source. This technique allows for two-DOF motion measurement of the linear and pitch motions of nanopositioning systems. Two capacitive sensors (CSs) are used for a baseline comparison with the proposed sensor by simultaneously measuring the motions of the nanopositioning system. The experimental results show that the proposed sensor closely agrees with the fundamental linear motion of the CS. However, the two-DOF OKES technology was shown to be approximately three times more sensitive to the pitch motion than the CS. The discrepancy in the two sensor outputs is discussed in terms of measuring principle, linearity, bandwidth, control effectiveness, and resolution.

Hydrodeoxygenation of oils from cellulose in single and two-stage hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Rocha, J.D.; Snape, C.E. [Strathclyde Univ., Glasgow (United Kingdom); Luengo, C.A. [Universidade Estadual de Campinas, SP (Brazil). Dept. de Fisica Aplicada

1996-09-01

To investigate the removal of oxygen (hydrodeoxygenation) during the hydropyrolysis of cellulose, single and two-stage experiments on pure cellulose have been carried out using hydrogen pressures up to 10 MPa and temperatures over the range 300-520{sup o}C. Carbon, oxygen and aromaticity balances have been determined from the product yields and compositions. For the two-stage tests, the primary oils were passed through a bed of commercial Ni/Mo {gamma}-alumina-supported catalyst (Criterion 424, presulphided) at 400{sup o}C. Raising the hydrogen pressure from atmospheric to 10 MPa increased the carbon conversion by 10 mole % which was roughly equally divided between the oil and hydrocarbon gases. The oxygen content of the primary oil was reduced by over 10% to below 20% w/w. The addition of a dispersed iron sulphide catalyst further increased the oil yield at 10 MPa and reduces the oxygen content of the oil by a further 10%. The effect of hydrogen pressure on oil yields was most pronounced at low flow rates where it is beneficial in helping to overcome diffusional resistances. Unlike the dispersed iron sulphide in the first stage, the use of the Ni-Mo catalyst in the second stage reduced both the oxygen content and aromaticity of the oils. (Author)

A Two-Stage Method for Structural Damage Prognosis in Shear Frames Based on Story Displacement Index and Modal Residual Force

Directory of Open Access Journals (Sweden)

Asghar Rasouli

2015-01-01

Full Text Available A two-stage method is proposed to properly identify the location and the extent of damage in shear frames. In the first stage, a story displacement index (SDI is presented to precisely locate the damage in the shear frame which is calculated using the modal analysis information of the damaged structure. In the second stage, by defining a new objective function, the extent of the actual damage is determined via an imperialist competitive algorithm. The performance of the proposed method is demonstrated by implementing the technique to three examples containing five-, ten-, and twenty-five-story shear frames with noises and without them in modal data. Moreover, the performance of the proposed method has been verified through using a benchmark problem. Numerical results show the high efficiency of the proposed method for accurately identifying the location and the extent of structural damage in shear frames.

SUCCESS FACTORS IN GROWING SMBs: A STUDY OF TWO INDUSTRIES AT TWO STAGES OF DEVELOPMENT

Directory of Open Access Journals (Sweden)

Tor Jarl Trondsen

2002-01-01

Full Text Available The study attempts to identify factors for growing SMBs. An evolutionary phase approach has been used. The study also aims to find out if there are common and different denominators for newer and older firms that can affect their profitability. The study selects a sampling frame that isolates two groups of firms in two industries at two stages of development. A variety of organizational and structural data was collected and analyzed. Amongst the conclusions that may be drawn from the study are that it is not easy to find a common definition of success, it is important to stratify SMBs when studying them, an evolutionary stage approach helps to compare firms with roughly the same external and internal dynamics and each industry has its own set of success variables.The study has identified three success variables for older firms that reflect contemporary strategic thinking such as crafting a good strategy and changing it only incrementally, building core competencies and outsourcing the rest, and keeping up with innovation and honing competitive skills.

The hybrid two stage anticlockwise cycle for ecological energy conversion

Directory of Open Access Journals (Sweden)

Cyklis Piotr

2016-01-01

Full Text Available The anticlockwise cycle is commonly used for refrigeration, air conditioning and heat pumps applications. The application of refrigerant in the compression cycle is within the temperature limits of the triple point and the critical point. New refrigerants such as 1234yf or 1234ze have many disadvantages, therefore natural refrigerants application is favourable. The carbon dioxide and water can be applied only in the hybrid two stages cycle. The possibilities of this solutions are shown for refrigerating applications, as well some experimental results of the adsorption-compression double stages cycle, powered with solar collectors are shown. As a high temperature cycle the adsorption system is applied. The low temperature cycle is the compression stage with carbon dioxide as a working fluid. This allows to achieve relatively high COP for low temperature cycle and for the whole system.

Two-Stage Part-Based Pedestrian Detection

DEFF Research Database (Denmark)

Møgelmose, Andreas; Prioletti, Antonio; Trivedi, Mohan M.

2012-01-01

Detecting pedestrians is still a challenging task for automotive vision system due the extreme variability of targets, lighting conditions, occlusions, and high speed vehicle motion. A lot of research has been focused on this problem in the last 10 years and detectors based on classifiers has...... gained a special place among the different approaches presented. This work presents a state-of-the-art pedestrian detection system based on a two stages classifier. Candidates are extracted with a Haar cascade classifier trained with the DaimlerDB dataset and then validated through part-based HOG...... of several metrics, such as detection rate, false positives per hour, and frame rate. The novelty of this system rely in the combination of HOG part-based approach, tracking based on specific optimized feature and porting on a real prototype....

Anaerobic digestion of citrus waste using two-stage membrane bioreactor

Science.gov (United States)

Millati, Ria; Lukitawesa; Dwi Permanasari, Ervina; Wulan Sari, Kartika; Nur Cahyanto, Muhammad; Niklasson, Claes; Taherzadeh, Mohammad J.

2018-03-01

Anaerobic digestion is a promising method to treat citrus waste. However, the presence of limonene in citrus waste inhibits anaerobic digestion process. Limonene is an antimicrobial compound and could inhibit methane forming bacteria that takes a longer time to recover than the injured acid forming bacteria. Hence, volatile fatty acids will be accumulated and methane production will be decreased. One way to solve this problem is by conducting anaerobic digestion process into two stages. The first step is aimed for hydrolysis, acidogenesis, and acetogenesis reactions and the second stage is aimed for methanogenesis reaction. The separation of the system would further allow each stage in their optimum conditions making the process more stable. In this research, anaerobic digestion was carried out in batch operations using 120 ml-glass bottle bioreactors in 2 stages. The first stage was performed in free-cells bioreactor, whereas the second stage was performed in both bioreactor of free cells and membrane bioreactor. In the first stage, the reactor was set into ‘anaerobic’ and ‘semi-aerobic’ conditions to examine the effect of oxygen on facultative anaerobic bacteria in acid production. In the second stage, the protection of membrane towards the cells against limonene was tested. For the first stage, the basal medium was prepared with 1.5 g VS of inoculum and 4.5 g VS of citrus waste. The digestion process was carried out at 55°C for four days. For the second stage, the membrane bioreactor was prepared with 3 g of cells that were encased and sealed in a 3×6 cm2 polyvinylidene fluoride membrane. The medium contained 40 ml basal medium and 10 ml liquid from the first stage. The bioreactors were incubated at 55°C for 2 days under anaerobic condition. The results from the first stage showed that the maximum total sugar under ‘anaerobic’ and ‘semi-aerobic’ conditions was 294.3 g/l and 244.7 g/l, respectively. The corresponding values for total volatile

Is the continuous two-stage anaerobic digestion process well suited for all substrates?

Science.gov (United States)

Lindner, Jonas; Zielonka, Simon; Oechsner, Hans; Lemmer, Andreas

2016-01-01

Two-stage anaerobic digestion systems are often considered to be advantageous compared to one-stage processes. Although process conditions and fermenter setups are well examined, overall substrate degradation in these systems is controversially discussed. Therefore, the aim of this study was to investigate how substrates with different fibre and sugar contents (hay/straw, maize silage, sugar beet) influence the degradation rate and methane production. Intermediates and gas compositions, as well as methane yields and VS-degradation degrees were recorded. The sugar beet substrate lead to a higher pH-value drop 5.67 in the acidification reactor, which resulted in a six time higher hydrogen production in comparison to the hay/straw substrate (pH-value drop 5.34). As the achieved yields in the two-stage system showed a difference of 70.6% for the hay/straw substrate, and only 7.8% for the sugar beet substrate. Therefore two-stage systems seem to be only recommendable for digesting sugar rich substrates. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessing efficiency and effectiveness of Malaysian Islamic banks: A two stage DEA analysis

Science.gov (United States)

Kamarudin, Norbaizura; Ismail, Wan Rosmanira; Mohd, Muhammad Azri

2014-06-01

Islamic banks in Malaysia are indispensable players in the financial industry with the growing needs for syariah compliance system. In the banking industry, most recent studies concerned only on operational efficiency. However rarely on the operational effectiveness. Since the production process of banking industry can be described as a two-stage process, two-stage Data Envelopment Analysis (DEA) can be applied to measure the bank performance. This study was designed to measure the overall performance in terms of efficiency and effectiveness of Islamic banks in Malaysia using Two-Stage DEA approach. This paper presents analysis of a DEA model which split the efficiency and effectiveness in order to evaluate the performance of ten selected Islamic Banks in Malaysia for the financial year period ended 2011. The analysis shows average efficient score is more than average effectiveness score thus we can say that Malaysian Islamic banks were more efficient rather than effective. Furthermore, none of the bank exhibit best practice in both stages as we can say that a bank with better efficiency does not always mean having better effectiveness at the same time.

Syntheses, characterizations and crystal structures of three new organically templated or organically bonded zinc selenates

International Nuclear Information System (INIS)

Feng Meiling; Mao Jianggao; Song Junling

2004-01-01

Three new organically templated or organically bonded zinc selenates, namely, {H 2 bipy}Zn(SeO 4 ) 2 (H 2 O) 2 1 (bipy=4,4'-bipyridine), {H 2 pip}{Zn(SeO 4 ) 2 (H 2 O) 4 }·2H 2 O 2 (pip=piprazine), and Zn(SeO 4 )(phen)(H 2 O) 2 3 (phen=1,10-phenanthroline) have been synthesized by hydrothermal reactions. The structure of compound 1 features a 1D chain composed of [Zn(SeO 4 ) 2 (H 2 O) 2 ] 2- anions. Compound 2 has a 2D layer structure built from {Zn(SeO 4 ) 2 (H 2 O) 4 } 2- anions that are cross-linked by doubly protonated piperazine cations via N-H···O hydrogen bonds. The structure of compound 3 contains a 1D chain of Zn(SeO 4 )(phen)(H 2 O) 2 , such chains are further interlinked by hydrogen bonds and π···π interactions to form a layer. The different roles the templates played have also been discussed

Engineering analysis of the two-stage trifluoride precipitation process

International Nuclear Information System (INIS)

Luerkens, D.w.W.

1984-06-01

An engineering analysis of two-stage trifluoride precipitation processes is developed. Precipitation kinetics are modeled using consecutive reactions to represent fluoride complexation. Material balances across the precipitators are used to model the time dependent concentration profiles of the main chemical species. The results of the engineering analysis are correlated with previous experimental work on plutonium trifluoride and cerium trifluoride

Recent developments of a two-stage light gas gun for pellet injection

International Nuclear Information System (INIS)

Reggiori, A.

1984-01-01

A report is given on a two-stage pneumatic gun operated with ambient air as first stage driver which has been built and tested. Cylindrical polyethylene pellets of 1 mm diameter and 1 mm length have been launched at velocities up to 1800 m/s, with divergence angles of the pellet trajectory less than 1 0 . It is possible to optimize the pressure pulse for pellets of different masses, simply changing the mass of the piston and/or the initial pressures in the second stage. (author)

Two-stage acid saccharification of fractionated Gelidium amansii minimizing the sugar decomposition.

Science.gov (United States)

Jeong, Tae Su; Kim, Young Soo; Oh, Kyeong Keun

2011-11-01

Two-stage acid hydrolysis was conducted on easy reacting cellulose and resistant reacting cellulose of fractionated Gelidium amansii (f-GA). Acid hydrolysis of f-GA was performed at between 170 and 200 °C for a period of 0-5 min, and an acid concentration of 2-5% (w/v, H2SO4) to determine the optimal conditions for acid hydrolysis. In the first stage of the acid hydrolysis, an optimum glucose yield of 33.7% was obtained at a reaction temperature of 190 °C, an acid concentration of 3.0%, and a reaction time of 3 min. In the second stage, a glucose yield of 34.2%, on the basis the amount of residual cellulose from the f-GA, was obtained at a temperature of 190 °C, a sulfuric acid concentration of 4.0%, and a reaction time 3.7 min. Finally, 68.58% of the cellulose derived from f-GA was converted into glucose through two-stage acid saccharification under aforementioned conditions. Copyright © 2011 Elsevier Ltd. All rights reserved.

Two-stage nuclear refrigeration with enhanced nuclear moments

International Nuclear Information System (INIS)

Hunik, R.

1979-01-01

Experiments are described in which an enhanced nuclear system is used as a precoolant for a nuclear demagnetisation stage. The results show the promising advantages of such a system in those circumstances for which a large cooling power is required at extremely low temperatures. A theoretical review of nuclear enhancement at the microscopic level and its macroscopic thermodynamical consequences is given. The experimental equipment for the implementation of the nuclear enhanced refrigeration method is described and the experiments on two-stage nuclear demagnetisation are discussed. With the nuclear enhanced system PrCu 6 the author could precool a nuclear stage of indium in a magnetic field of 6 T down to temperatures below 10 mK; this resulted in temperature below 1 mK after demagnetisation of the indium. It is demonstrated that the interaction energy between the nuclear moments in an enhanced nuclear system can exceed the nuclear dipolar interaction. Several experiments are described on pulsed nuclear magnetic resonance, as utilised for thermometry purposes. It is shown that platinum NMR-thermometry gives very satisfactory results around 1 mK. The results of experiments on nuclear orientation of radioactive nuclei, e.g. the brute force polarisation of 95 NbPt and 60 CoCu, are presented, some of which are of major importance for the thermometry in the milli-Kelvin region. (Auth.)

Modelling of Two-Stage Methane Digestion With Pretreatment of Biomass

Science.gov (United States)

Dychko, A.; Remez, N.; Opolinskyi, I.; Kraychuk, S.; Ostapchuk, N.; Yevtieieva, L.

2018-04-01

Systems of anaerobic digestion should be used for processing of organic waste. Managing the process of anaerobic recycling of organic waste requires reliable predicting of biogas production. Development of mathematical model of process of organic waste digestion allows determining the rate of biogas output at the two-stage process of anaerobic digestion considering the first stage. Verification of Konto's model, based on the studied anaerobic processing of organic waste, is implemented. The dependencies of biogas output and its rate from time are set and may be used to predict the process of anaerobic processing of organic waste.

Two biased estimation techniques in linear regression: Application to aircraft

Science.gov (United States)

Klein, Vladislav

1988-01-01

Several ways for detection and assessment of collinearity in measured data are discussed. Because data collinearity usually results in poor least squares estimates, two estimation techniques which can limit a damaging effect of collinearity are presented. These two techniques, the principal components regression and mixed estimation, belong to a class of biased estimation techniques. Detection and assessment of data collinearity and the two biased estimation techniques are demonstrated in two examples using flight test data from longitudinal maneuvers of an experimental aircraft. The eigensystem analysis and parameter variance decomposition appeared to be a promising tool for collinearity evaluation. The biased estimators had far better accuracy than the results from the ordinary least squares technique.

Influence of capacity- and time-constrained intermediate storage in two-stage food production systems

DEFF Research Database (Denmark)

Akkerman, Renzo; van Donk, Dirk Pieter; Gaalman, Gerard

2007-01-01

In food processing, two-stage production systems with a batch processor in the first stage and packaging lines in the second stage are common and mostly separated by capacity- and time-constrained intermediate storage. This combination of constraints is common in practice, but the literature hardly...... of systems like this. Contrary to the common sense in operations management, the LPT rule is able to maximize the total production volume per day. Furthermore, we show that adding one tank has considerable effects. Finally, we conclude that the optimal setup frequency for batches in the first stage...... pays any attention to this. In this paper, we show how various capacity and time constraints influence the performance of a specific two-stage system. We study the effects of several basic scheduling and sequencing rules in the presence of these constraints in order to learn the characteristics...

A robust and simple two-mode digital calibration technique for pipelined ADC

Energy Technology Data Exchange (ETDEWEB)

Yin Xiumei; Zhao Nan; Sekedi Bomeh Kobenge; Yang Huazhong, E-mail: yxm@mails.tsinghua.edu.cn [Department of Electronic Engineering, Tsinghua University, Beijing 100084 (China)

2011-03-15

This paper presents a two-mode digital calibration technique for pipelined analog-to-digital converters (ADC). The proposed calibration eliminates the errors of residual difference voltage induced by capacitor mismatch of pseudorandom (PN) sequence injection capacitors at the ADC initialization, while applies digital background calibration to continuously compensate the interstage gain errors in ADC normal operation. The presented technique not only reduces the complexity of analog circuit by eliminating the implementation of PN sequence with accurate amplitude in analog domain, but also improves the performance of digital background calibration by minimizing the sensitivity of calibration accuracy to sub-ADC errors. The use of opamps with low DC gains in normal operation makes the proposed design more compatible with future nanometer CMOS technology. The prototype of a 12-bit 40-MS/s pipelined ADC with the two-mode digital calibration is implemented in 0.18-{mu}m CMOS process. Adopting a simple telescopic opamp with a DC gain of 58-dB in the first stage, the measured SFDR and SNDR within the first Nyquist zone reach 80-dB and 66-dB, respectively. With the calibration, the maximum integral nonlinearity (INL) of the ADC reduces from 4.75-LSB to 0.65-LSB, while the ADC core consumes 82-mW at 3.3-V power supply. (semiconductor integrated circuits)

Maximum likelihood estimation of signal detection model parameters for the assessment of two-stage diagnostic strategies.

Science.gov (United States)

Lirio, R B; Dondériz, I C; Pérez Abalo, M C

1992-08-01

The methodology of Receiver Operating Characteristic curves based on the signal detection model is extended to evaluate the accuracy of two-stage diagnostic strategies. A computer program is developed for the maximum likelihood estimation of parameters that characterize the sensitivity and specificity of two-stage classifiers according to this extended methodology. Its use is briefly illustrated with data collected in a two-stage screening for auditory defects.

Two-Stage Load Shedding for Secondary Control in Hierarchical Operation of Islanded Microgrids

DEFF Research Database (Denmark)

Zhou, Quan; Li, Zhiyi; Wu, Qiuwei

2018-01-01

A two-stage load shedding scheme is presented to cope with the severe power deficit caused by microgrid islanding. Coordinated with the fast response of inverter-based distributed energy resources (DERs), load shedding at each stage and the resulting power flow redistribution are estimated....... The first stage of load shedding will cease rapid frequency decline in which the measured frequency deviation is employed to guide the load shedding level and process. Once a new steady-state is reached, the second stage is activated, which performs load shedding according to the priorities of loads...

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure

DEFF Research Database (Denmark)

Nielsen, H.B.; Mladenovska, Zuzana; Westermann, Peter

2004-01-01

A two-stage 68degreesC/55degreesC anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68degrees......, was compared with a conventional single-stage reactor running at 55degreesC with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single......-stage reactor. The 68degreesC reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic...

Application of two-stage biofilter system for the removal of odorous compounds.

Science.gov (United States)

Jeong, Gwi-Taek; Park, Don-Hee; Lee, Gwang-Yeon; Cha, Jin-Myeong

2006-01-01

Biofiltration is a biological process which is considered to be one of the more successful examples of biotechnological applications to environmental engineering, and is most commonly used in the removal of odoriferous compounds. In this study, we have attempted to assess the efficiency with which both single and complex odoriferous compounds could be removed, using one- or two-stage biofiltration systems. The tested single odor gases, limonene, alpha-pinene, and iso-butyl alcohol, were separately evaluated in the biofilters. Both limonene and alpha-pinene were removed by 90% or more EC (elimination capacity), 364 g/m3/h and 321 g/m3/h, respectively, at an input concentration of 50 ppm and a retention time of 30 s. The iso-butyl alcohol was maintained with an effective removal yield of more than 90% (EC 375 g/m3/h) at an input concentration of 100 ppm. The complex gas removal scheme was applied with a 200 ppm inlet concentration of ethanol, 70 ppm of acetaldehyde, and 70 ppm of toluene with residence time of 45 s in a one- or two-stage biofiltration system. The removal yield of toluene was determined to be lower than that of the other gases in the one-stage biofilter. Otherwise, the complex gases were sufficiently eliminated by the two-stage biofiltration system.

A Concept of Two-Stage-To-Orbit Reusable Launch Vehicle

Science.gov (United States)

Yang, Yong; Wang, Xiaojun; Tang, Yihua

2002-01-01

Reusable Launch Vehicle (RLV) has a capability of delivering a wide rang of payload to earth orbit with greater reliability, lower cost, more flexibility and operability than any of today's launch vehicles. It is the goal of future space transportation systems. Past experience on single stage to orbit (SSTO) RLVs, such as NASA's NASP project, which aims at developing an rocket-based combined-cycle (RBCC) airplane and X-33, which aims at developing a rocket RLV, indicates that SSTO RLV can not be realized in the next few years based on the state-of-the-art technologies. This paper presents a concept of all rocket two-stage-to-orbit (TSTO) reusable launch vehicle. The TSTO RLV comprises an orbiter and a booster stage. The orbiter is mounted on the top of the booster stage. The TSTO RLV takes off vertically. At the altitude about 50km the booster stage is separated from the orbiter, returns and lands by parachutes and airbags, or lands horizontally by means of its own propulsion system. The orbiter continues its ascent flight and delivers the payload into LEO orbit. After completing orbit mission, the orbiter will reenter into the atmosphere, automatically fly to the ground base and finally horizontally land on the runway. TSTO RLV has less technology difficulties and risk than SSTO, and maybe the practical approach to the RLV in the near future.

Could new reconstruction CT techniques challenge MRI for the detection of brain metastases in the context of initial lung cancer staging?

Energy Technology Data Exchange (ETDEWEB)

Millon, Domitille; Byl, David; Coche, Emmanuel E. [Universite Catholique de Louvain, Department of Radiology and Medical Imaging, Cliniques Universitaires Saint Luc, Brussels (Belgium); Collard, Philippe [Universite Catholique de Louvain, Department of Pneumology, Cliniques Universitaires Saint Luc, Brussels (Belgium); Cambier, Samantha E.; Maanen, Aline G. van [Universite Catholique de Louvain, Statistic Unit, King Albert II Cancer Institute, Brussels (Belgium); Vlassenbroek, Alain [Philips Healthcare, Brussels (Belgium)

2018-02-15

To evaluate the diagnostic performance of brain CT images reconstructed with a model-based iterative algorithm performed at usual and reduced dose. 115 patients with histologically proven lung cancer were prospectively included over 15 months. Patients underwent two CT acquisitions at the initial staging, performed on a 256-slice MDCT, at standard (CTDIvol: 41.4 mGy) and half dose (CTDIvol: 20.7 mGy). Both image datasets were reconstructed with filtered back projection (FBP) and iterative model-based reconstruction (IMR) algorithms. Brain MRI was considered as the reference. Two blinded independent readers analysed the images. Ninety-three patients underwent all examinations. At the standard dose, eight patients presented 17 and 15 lesions on IMR and FBP CT images, respectively. At half-dose, seven patients presented 15 and 13 lesions on IMR and FBP CT images, respectively. The test could not highlight any significant difference between the standard dose IMR and the half-dose FBP techniques (p-value = 0.12). MRI showed 46 metastases on 11 patients. Specificity, negative and positive predictive values were calculated (98.9-100 %, 93.6-94.6 %, 75-100 %, respectively, for all CT techniques). No significant difference could be demonstrated between the two CT reconstruction techniques. (orig.)

Evaluating damping elements for two-stage suspension vehicles

Directory of Open Access Journals (Sweden)

Ronald M. Martinod R.

2012-01-01

Full Text Available The technical state of the damping elements for a vehicle having two-stage suspension was evaluated by using numerical models based on the multi-body system theory; a set of virtual tests used the eigenproblem mathematical method. A test was developed based on experimental modal analysis (EMA applied to a physical system as the basis for validating the numerical models. The study focused on evaluating vehicle dynamics to determine the influence of the dampers’ technical state in each suspension state.

Sample size reassessment for a two-stage design controlling the false discovery rate.

Science.gov (United States)

Zehetmayer, Sonja; Graf, Alexandra C; Posch, Martin

2015-11-01

Sample size calculations for gene expression microarray and NGS-RNA-Seq experiments are challenging because the overall power depends on unknown quantities as the proportion of true null hypotheses and the distribution of the effect sizes under the alternative. We propose a two-stage design with an adaptive interim analysis where these quantities are estimated from the interim data. The second stage sample size is chosen based on these estimates to achieve a specific overall power. The proposed procedure controls the power in all considered scenarios except for very low first stage sample sizes. The false discovery rate (FDR) is controlled despite of the data dependent choice of sample size. The two-stage design can be a useful tool to determine the sample size of high-dimensional studies if in the planning phase there is high uncertainty regarding the expected effect sizes and variability.

Theoretical and experimental investigations on the cooling capacity distributions at the stages in the thermally-coupled two-stage Stirling-type pulse tube cryocooler without external precooling

Science.gov (United States)

Tan, Jun; Dang, Haizheng

2017-03-01

The two-stage Stirling-type pulse tube cryocooler (SPTC) has advantages in simultaneously providing the cooling powers at two different temperatures, and the capacity in distributing these cooling capacities between the stages is significant to its practical applications. In this paper, a theoretical model of the thermally-coupled two-stage SPTC without external precooling is established based on the electric circuit analogy with considering real gas effects, and the simulations of both the cooling performances and PV power distribution between stages are conducted. The results indicate that the PV power is inversely proportional to the acoustic impedance of each stage, and the cooling capacity distribution is determined by the cold finger cooling efficiency and the PV power into each stage together. The design methods of the cold fingers to achieve both the desired PV power and the cooling capacity distribution between the stages are summarized. The two-stage SPTC is developed and tested based on the above theoretical investigations, and the experimental results show that it can simultaneously achieve 0.69 W at 30 K and 3.1 W at 85 K with an electric input power of 330 W and a reject temperature of 300 K. The consistency between the simulated and the experimental results is observed and the theoretical investigations are experimentally verified.

Building fast well-balanced two-stage numerical schemes for a model of two-phase flows

Science.gov (United States)

Thanh, Mai Duc

2014-06-01

We present a set of well-balanced two-stage schemes for an isentropic model of two-phase flows arisen from the modeling of deflagration-to-detonation transition in granular materials. The first stage is to absorb the source term in nonconservative form into equilibria. Then in the second stage, these equilibria will be composed into a numerical flux formed by using a convex combination of the numerical flux of a stable Lax-Friedrichs-type scheme and the one of a higher-order Richtmyer-type scheme. Numerical schemes constructed in such a way are expected to get the interesting property: they are fast and stable. Tests show that the method works out until the parameter takes on the value CFL, and so any value of the parameter between zero and this value is expected to work as well. All the schemes in this family are shown to capture stationary waves and preserves the positivity of the volume fractions. The special values of the parameter 0,1/2,1/(1+CFL), and CFL in this family define the Lax-Friedrichs-type, FAST1, FAST2, and FAST3 schemes, respectively. These schemes are shown to give a desirable accuracy. The errors and the CPU time of these schemes and the Roe-type scheme are calculated and compared. The constructed schemes are shown to be well-balanced and faster than the Roe-type scheme.

Two-stage pervaporation process for effective in situ removal acetone-butanol-ethanol from fermentation broth.

Science.gov (United States)

Cai, Di; Hu, Song; Miao, Qi; Chen, Changjing; Chen, Huidong; Zhang, Changwei; Li, Ping; Qin, Peiyong; Tan, Tianwei

2017-01-01

Two-stage pervaporation for ABE recovery from fermentation broth was studied to reduce the energy cost. The permeate after the first stage in situ pervaporation system was further used as the feedstock in the second stage of pervaporation unit using the same PDMS/PVDF membrane. A total 782.5g/L of ABE (304.56g/L of acetone, 451.98g/L of butanol and 25.97g/L of ethanol) was achieved in the second stage permeate, while the overall acetone, butanol and ethanol separation factors were: 70.7-89.73, 70.48-84.74 and 9.05-13.58, respectively. Furthermore, the theoretical evaporation energy requirement for ABE separation in the consolidate fermentation, which containing two-stage pervaporation and the following distillation process, was estimated less than ∼13.2MJ/kg-butanol. The required evaporation energy was only 36.7% of the energy content of butanol. The novel two-stage pervaporation process was effective in increasing ABE production and reducing energy consumption of the solvents separation system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Two-stage solar concentrators based on parabolic troughs: asymmetric versus symmetric designs.

Science.gov (United States)

Schmitz, Max; Cooper, Thomas; Ambrosetti, Gianluca; Steinfeld, Aldo

2015-11-20

While nonimaging concentrators can approach the thermodynamic limit of concentration, they generally suffer from poor compactness when designed for small acceptance angles, e.g., to capture direct solar irradiation. Symmetric two-stage systems utilizing an image-forming primary parabolic concentrator in tandem with a nonimaging secondary concentrator partially overcome this compactness problem, but their achievable concentration ratio is ultimately limited by the central obstruction caused by the secondary. Significant improvements can be realized by two-stage systems having asymmetric cross-sections, particularly for 2D line-focus trough designs. We therefore present a detailed analysis of two-stage line-focus asymmetric concentrators for flat receiver geometries and compare them to their symmetric counterparts. Exemplary designs are examined in terms of the key optical performance metrics, namely, geometric concentration ratio, acceptance angle, concentration-acceptance product, aspect ratio, active area fraction, and average number of reflections. Notably, we show that asymmetric designs can achieve significantly higher overall concentrations and are always more compact than symmetric systems designed for the same concentration ratio. Using this analysis as a basis, we develop novel asymmetric designs, including two-wing and nested configurations, which surpass the optical performance of two-mirror aplanats and are comparable with the best reported 2D simultaneous multiple surface designs for both hollow and dielectric-filled secondaries.

Development of a two-stage inspection process for the assessment of deteriorating infrastructure

International Nuclear Information System (INIS)

Sheils, Emma; O'Connor, Alan; Breysse, Denys; Schoefs, Franck; Yotte, Sylvie

2010-01-01

Inspection-based maintenance strategies can provide an efficient tool for the management of ageing infrastructure subjected to deterioration. Many of these methods rely on quantitative data from inspections, rather than qualitative and subjective data. The focus of this paper is on the development of an inspection-based decision scheme, incorporating analysis on the effect of the cost and quality of NDT tools to assess the condition of infrastructure elements/networks during their lifetime. For the first time the two aspects of an inspection are considered, i.e. detection and sizing. Since each stage of an inspection is carried out for a distinct purpose, different parameters are used to represent each procedure and both have been incorporated into a maintenance management model. The separation of these procedures allows the interaction between the two inspection techniques to be studied. The inspection for detection process acts as a screening exercise to determine which defects require further inspection for sizing. A decision tool is developed that allows the owner/manager of the infrastructural element/network to choose the most cost-efficient maintenance management plan based on his/her specific requirements.

EOG and EMG: two important switches in automatic sleep stage classification.

Science.gov (United States)

Estrada, E; Nazeran, H; Barragan, J; Burk, J R; Lucas, E A; Behbehani, K

2006-01-01

Sleep is a natural periodic state of rest for the body, in which the eyes are usually closed and consciousness is completely or partially lost. In this investigation we used the EOG and EMG signals acquired from 10 patients undergoing overnight polysomnography with their sleep stages determined by expert sleep specialists based on RK rules. Differentiation between Stage 1, Awake and REM stages challenged a well trained neural network classifier to distinguish between classes when only EEG-derived signal features were used. To meet this challenge and improve the classification rate, extra features extracted from EOG and EMG signals were fed to the classifier. In this study, two simple feature extraction algorithms were applied to EOG and EMG signals. The statistics of the results were calculated and displayed in an easy to visualize fashion to observe tendencies for each sleep stage. Inclusion of these features show a great promise to improve the classification rate towards the target rate of 100%

Improvement of two-stage GM refrigerator performance using a hybrid regenerator

International Nuclear Information System (INIS)

Ke, G.; Makuuchi, H.; Hashimoto, T.; Onishi, A.; Li, R.; Satoh, T.; Kanazawa, Y.

1994-01-01

To improve the performance of two-stage GM refrigerators, a hybrid regenerator with magnetic materials of Er 3 Ni and ErNi 0.9 Co 0.1 was used in the 2nd stage regenerator because of its large heat exchange capacity. The largest refrigeration capacity achieved with the hybrid regenerator was 0.95W at helium liquefied temperature of 4.2K. This capacity is 15.9% greater than the 0.82W refrigerator with only Er 3 Ni as the 2nd regenerator material. Use of the hybrid regenerator not only increases the refrigeration capacity at 4.2K, but also allows the 4K GM refrigerator to be used with large 1st stage refrigeration capacity, thus making it more practical

NxStage dialysis system-associated thrombocytopenia: a report of two cases.

Science.gov (United States)

Sekkarie, Mohamed; Waldron, Michelle; Reynolds, Texas

2016-01-01

Thrombocytopenia in hemodialysis patients has recently been reported to be commonly caused by electron-beam sterilization of dialysis filters. We report the occurrence of thrombocytopenia in the first two patients of a newly established home hemodialysis program. The 2 patients switched from conventional hemodialysis using polysulfone electron-beam sterilized dialyzers to a NxStage system, which uses gamma sterilized polyehersulfone dialyzers incorporated into a drop-in cartridge. The thrombocytopenia resolved after return to conventional dialysis in both patients and recurred upon rechallenge in the patient who opted to retry NxStage. This is the first report of thrombocytopenia with the NxStage system according to the authors’ knowledge. Dialysis-associated thrombocytopenia pathophysiology and clinical significance are not well understood and warrant additional investigations.

Evaluation of the effect of one stage versus two stage full mouth disinfection on C-reactive protein and leucocyte count in patients with chronic periodontitis.

Science.gov (United States)

Pabolu, Chandra Mohan; Mutthineni, Ramesh Babu; Chintala, Srikanth; Naheeda; Mutthineni, Navya

2013-07-01

Conventional non-surgical periodontal therapy is carried out in quadrant basis with 1-2 week interval. This time lag may result in re-infection of instrumented pocket and may impair healing. Therefore, a new approach to full-mouth non-surgical therapy to be completed within two consecutive days with full-mouth disinfection has been suggested. In periodontitis, leukocyte counts and levels of C-reactive protein (CRP) are likely to be slightly elevated, indicating the presence of infection or inflammation. The aim of this study is to compare the efficacy of one stage and two stage non-surgical therapy on clinical parameters along with CRP levels and total white blood cell (TWBC) count. A total of 20 patients were selected and were divided into two groups. Group 1 received one stage full mouth dis-infection and Group 2 received two stages FMD. Plaque index, sulcus bleeding index, probing depth, clinical attachment loss, serum CRP and TWBC count were evaluated for both the groups at baseline and at 1 month post-treatment. The results were analyzed using the Student t-test. Both treatment modalities lead to a significant improvement of the clinical and hematological parameters; however comparison between the two groups showed no significant difference after 1 month. The therapeutic intervention may have a systemic effect on blood count in periodontitis patients. Though one stage FMD had limited benefits over two stages FMD, the therapy can be accomplished in a shorter duration.

A Two-Stage Fuzzy Logic Control Method of Traffic Signal Based on Traffic Urgency Degree

OpenAIRE

Yan Ge

2014-01-01

City intersection traffic signal control is an important method to improve the efficiency of road network and alleviate traffic congestion. This paper researches traffic signal fuzzy control method on a single intersection. A two-stage traffic signal control method based on traffic urgency degree is proposed according to two-stage fuzzy inference on single intersection. At the first stage, calculate traffic urgency degree for all red phases using traffic urgency evaluation module and select t...

The transillumination technique as a method for the assessment of spermatogenesis using medicinal plants: the effect of extracts of black maca (Lepidium meyenii) and camu camu (Myrciaria dubia) on stages of the spermatogenic cycle in male rats.

Science.gov (United States)

Gonzales, Gustavo F; Vasquez, Vanessa Bertha; Gasco, Manuel

2013-10-01

Transillumination technique for assessment of stages of spermatogenic cycle is a useful tool for toxicological studies. This study was designed to determine the effect of two medicinal plants on spermatogenesis in male rats using the transillumination technique. For this, the effect of the combination of a fruit with highest content of ascorbic acid (Myrciaria dubia, camu camu) and extract of black maca (Lepidium meyenii) on seminiferous tubule stages scored by transillumination on intact tubules in adult male rats was assessed. Animals were treated during seven days with vehicle, black maca, camu camu or a mixture of black maca + camu camu and assessed for daily sperm production (DSP), stages of spermatogenic cycle as well as antioxidant activity and levels of flavonoids and polyphenols. Black maca increased stages of spermiation (VII-VIII) and mitosis of germ cells (IX-XI), whereas camu camu increased stages of mitosis (IX-XI) and meiosis (XII). Mixture of maca + camu camu increased stages of spermiation, mitosis and meiosis. All treatments increased DSP (pmaca. In conclusion, M. dubia (camu camu) has potential effects improving spermatogenesis and co-administered with maca increase stages of mitosis, meiosis and spermiation of the spermatogenic cycle as assessed by the transillumination technique. This technique is becoming increasingly a useful tool for assessment spermatogenesis.

Possible two-stage 87Sr evolution in the Stockdale Rhyolite

International Nuclear Information System (INIS)

Compston, W.; McDougall, I.; Wyborn, D.

1982-01-01

The Rb-Sr total-rock data for the Stockdale Rhyolite, of significance for the Palaeozoic time scale, are more scattered about a single-stage isochron than expected from experimental error. Two-stage 87 Sr evolution for several of the samples is explored to explain this, as an alternative to variation in the initial 87 Sr/ 86 Sr which is customarily used in single-stage dating models. The deletion of certain samples having very high Rb/Sr removes most of the excess scatter and leads to an estimate of 430 +- 7 m.y. for the age of extrusion. There is a younger alignment of Rb-Sr data within each sampling site at 412 +- 7 m.y. We suggest that the Stockdale Rhyolite is at least 430 m.y. old, that its original range in Rb/Sr was smaller than now observed, and that it experienced a net loss in Sr during later hydrothermal alteration at ca. 412 m.y. (orig.)

Thermodynamics analysis of a modified dual-evaporator CO2 transcritical refrigeration cycle with two-stage ejector

International Nuclear Information System (INIS)

Bai, Tao; Yan, Gang; Yu, Jianlin

2015-01-01

In this paper, a modified dual-evaporator CO 2 transcritical refrigeration cycle with two-stage ejector (MDRC) is proposed. In MDRC, the two-stage ejector are employed to recover the expansion work from cycle throttling processes and enhance the system performance and obtain dual-temperature refrigeration simultaneously. The effects of some key parameters on the thermodynamic performance of the modified cycle are theoretically investigated based on energetic and exergetic analyses. The simulation results for the modified cycle show that two-stage ejector exhibits more effective system performance improvement than the single ejector in CO 2 dual-temperature refrigeration cycle, and the improvements of the maximum system COP (coefficient of performance) and system exergy efficiency could reach 37.61% and 31.9% over those of the conventional dual-evaporator cycle under the given operating conditions. The exergetic analysis for each component at optimum discharge pressure indicates that the gas cooler, compressor, two-stage ejector and expansion valves contribute main portion to the total system exergy destruction, and the exergy destruction caused by the two-stage ejector could amount to 16.91% of the exergy input. The performance characteristics of the proposed cycle show its promise in dual-evaporator refrigeration system. - Highlights: • Two-stage ejector is used in dual-evaporator CO 2 transcritical refrigeration cycle. • Energetic and exergetic methods are carried out to analyze the system performance. • The modified cycle could obtain dual-temperature refrigeration simultaneously. • Two-stage ejector could effectively improve system COP and exergy efficiency

The experimental study of a two-stage photovoltaic thermal system based on solar trough concentration

International Nuclear Information System (INIS)

Tan, Lijun; Ji, Xu; Li, Ming; Leng, Congbin; Luo, Xi; Li, Haili

2014-01-01

Highlights: • A two-stage photovoltaic thermal system based on solar trough concentration. • Maximum cell efficiency of 5.21% with the mirror opening width of 57 cm. • With single cycle, maximum temperatures rise in the heating stage is 12.06 °C. • With 30 min multiple cycles, working medium temperature 62.8 °C, increased 28.7 °C. - Abstract: A two-stage photovoltaic thermal system based on solar trough concentration is proposed, in which the metal cavity heating stage is added on the basis of the PV/T stage, and thermal energy with higher temperature is output while electric energy is output. With the 1.8 m 2 mirror PV/T system, the characteristic parameters of the space solar cell under non-concentrating solar radiation and concentrating solar radiation are respectively tested experimentally, and the solar cell output characteristics at different opening widths of concentrating mirror of the PV/T stage under condensation are also tested experimentally. When the mirror opening width was 57 cm, the solar cell efficiency reached maximum value of 5.21%. The experimental platform of the two-stage photovoltaic thermal system was established, with a 1.8 m 2 mirror PV/T stage and a 15 m 2 mirror heating stage, or a 1.8 m 2 mirror PV/T stage and a 30 m 2 mirror heating stage. The results showed that with single cycle, the long metal cavity heating stage would bring lower thermal efficiency, but temperature rise of the working medium is higher, up to 12.06 °C with only single cycle. With 30 min closed multiple cycles, the temperature of the working medium in the water tank was 62.8 °C, with an increase of 28.7 °C, and thermal energy with higher temperature could be output

Design and construction of the X-2 two-stage free piston driven expansion tube

Science.gov (United States)

Doolan, Con

1995-01-01

This report outlines the design and construction of the X-2 two-stage free piston driven expansion tube. The project has completed its construction phase and the facility has been installed in the new impulsive research laboratory where commissioning is about to take place. The X-2 uses a unique, two-stage driver design which allows a more compact and lower overall cost free piston compressor. The new facility has been constructed in order to examine the performance envelope of the two-stage driver and how well it couple to sub-orbital and super-orbital expansion tubes. Data obtained from these experiments will be used for the design of a much larger facility, X-3, utilizing the same free piston driver concept.

One-stage or two-stage revision surgery for prosthetic hip joint infection--the INFORM trial: a study protocol for a randomised controlled trial.

Science.gov (United States)

Strange, Simon; Whitehouse, Michael R; Beswick, Andrew D; Board, Tim; Burston, Amanda; Burston, Ben; Carroll, Fran E; Dieppe, Paul; Garfield, Kirsty; Gooberman-Hill, Rachael; Jones, Stephen; Kunutsor, Setor; Lane, Athene; Lenguerrand, Erik; MacGowan, Alasdair; Moore, Andrew; Noble, Sian; Simon, Joanne; Stockley, Ian; Taylor, Adrian H; Toms, Andrew; Webb, Jason; Whittaker, John-Paul; Wilson, Matthew; Wylde, Vikki; Blom, Ashley W

2016-02-17

Periprosthetic joint infection (PJI) affects approximately 1% of patients following total hip replacement (THR) and often results in severe physical and emotional suffering. Current surgical treatment options are debridement, antibiotics and implant retention; revision THR; excision of the joint and amputation. Revision surgery can be done as either a one-stage or two-stage operation. Both types of surgery are well-established practice in the NHS and result in similar rates of re-infection, but little is known about the impact of these treatments from the patient's perspective. The main aim of this randomised controlled trial is to determine whether there is a difference in patient-reported outcome measures 18 months after randomisation for one-stage or two-stage revision surgery. INFORM (INFection ORthopaedic Management) is an open, two-arm, multi-centre, randomised, superiority trial. We aim to randomise 148 patients with eligible PJI of the hip from approximately seven secondary care NHS orthopaedic units from across England and Wales. Patients will be randomised via a web-based system to receive either a one-stage revision or a two-stage revision THR. Blinding is not possible due to the nature of the intervention. All patients will be followed up for 18 months. The primary outcome is the WOMAC Index, which assesses hip pain, function and stiffness, collected by questionnaire at 18 months. Secondary outcomes include the following: cost-effectiveness, complications, re-infection rates, objective hip function assessment and quality of life. A nested qualitative study will explore patients' and surgeons' experiences, including their views about trial participation and randomisation. INFORM is the first ever randomised trial to compare two widely accepted surgical interventions for the treatment of PJI: one-stage and two-stage revision THR. The results of the trial will benefit patients in the future as the main focus is on patient-reported outcomes: pain, function

Two-stage laparoscopic approaches for high anorectal malformation: transumbilical colostomy and anorectoplasty.

Science.gov (United States)

Yang, Li; Tang, Shao-Tao; Li, Shuai; Aubdoollah, T H; Cao, Guo-Qing; Lei, Hai-Yan; Wang, Xin-Xing

2014-11-01

Trans-umbilical colostomy (TUC) has been previously created in patients with Hirschsprung's disease and intermediate anorectal malformation (ARM), but not in patients with high-ARM. The purposes of this study were to assess the feasibility, safety, complications and cosmetic results of TUC in a divided fashion, and subsequently stoma closure and laparoscopic assisted anorectoplasty (LAARP) were simultaneously completed by using the colostomy site for a laparoscopic port in high-ARM patients. Twenty male patients with high-ARMs were chosen for this two-stage procedure. The first-stage consisted of creating the TUC in double-barreled fashion colostomy with a high chimney at the umbilicus, and the loop was divided at the same time, in such a way that the two diverting ends were located at the umbilical incision with the distal end half closed and slightly higher than proximal end. In the second-stage, 3 to 7 months later, the stoma was closed through a peristomal skin incision followed by end-to-end anastomosis and simultaneously LAARP was performed by placing a laparoscopic port at the umbilicus, which was previously the colonostomy site. Umbilical wound closure was performed in a semi-opened fashion to create a deep umbilicus. TUC and LAARP were successfully performed in 20 patients. Four cases with bladder neck fistulas and 16 cases with prostatic urethra fistulas were found. Postoperative complications were rectal mucosal prolapsed in three cases, anal stricture in two cases and wound dehiscence in one case. Neither umbilical ring narrowing, parastomal hernia nor obstructive symptoms was observed. Neither umbilical nor perineal wound infection was observed. Stoma care was easily carried-out by attaching stoma bag. Healing of umbilical wounds after the second-stage was excellent. Early functional stooling outcome were satisfactory. The umbilicus may be an alternative stoma site for double-barreled colostomy in high-ARM patients. The two-stage laparoscopic

Adaptive Urban Stormwater Management Using a Two-stage Stochastic Optimization Model

Science.gov (United States)

Hung, F.; Hobbs, B. F.; McGarity, A. E.

2014-12-01

In many older cities, stormwater results in combined sewer overflows (CSOs) and consequent water quality impairments. Because of the expense of traditional approaches for controlling CSOs, cities are considering the use of green infrastructure (GI) to reduce runoff and pollutants. Examples of GI include tree trenches, rain gardens, green roofs, and rain barrels. However, the cost and effectiveness of GI are uncertain, especially at the watershed scale. We present a two-stage stochastic extension of the Stormwater Investment Strategy Evaluation (StormWISE) model (A. McGarity, JWRPM, 2012, 111-24) to explicitly model and optimize these uncertainties in an adaptive management framework. A two-stage model represents the immediate commitment of resources ("here & now") followed by later investment and adaptation decisions ("wait & see"). A case study is presented for Philadelphia, which intends to extensively deploy GI over the next two decades (PWD, "Green City, Clean Water - Implementation and Adaptive Management Plan," 2011). After first-stage decisions are made, the model updates the stochastic objective and constraints (learning). We model two types of "learning" about GI cost and performance. One assumes that learning occurs over time, is automatic, and does not depend on what has been done in stage one (basic model). The other considers learning resulting from active experimentation and learning-by-doing (advanced model). Both require expert probability elicitations, and learning from research and monitoring is modelled by Bayesian updating (as in S. Jacobi et al., JWRPM, 2013, 534-43). The model allocates limited financial resources to GI investments over time to achieve multiple objectives with a given reliability. Objectives include minimizing construction and O&M costs; achieving nutrient, sediment, and runoff volume targets; and community concerns, such as aesthetics, CO2 emissions, heat islands, and recreational values. CVaR (Conditional Value at Risk) and

Two stage approach to dynamic soil structure interaction

International Nuclear Information System (INIS)

Nelson, I.

1981-01-01

A two stage approach is used to reduce the effective size of soil island required to solve dynamic soil structure interaction problems. The ficticious boundaries of the conventional soil island are chosen sufficiently far from the structure so that the presence of the structure causes only a slight perturbation on the soil response near the boundaries. While the resulting finite element model of the soil structure system can be solved, it requires a formidable computational effort. Currently, a two stage approach is used to reduce this effort. The combined soil structure system has many frequencies and wavelengths. For a stiff structure, the lowest frequencies are those associated with the motion of the structure as a rigid body. In the soil, these modes have the longest wavelengths and attenuate most slowly. The higher frequency deformational modes of the structure have shorter wavelengths and their effect attenuates more rapidly with distance from the structure. The difference in soil response between a computation with a refined structural model, and one with a crude model, tends towards zero a very short distance from the structure. In the current work, the 'crude model' is a rigid structure with the same geometry and inertial properties as the refined model. Preliminary calculations indicated that a rigid structure would be a good low frequency approximation to the actual structure, provided the structure was much stiffer than the native soil. (orig./RW)

A Novel Two-Stage Dynamic Spectrum Sharing Scheme in Cognitive Radio Networks

Institute of Scientific and Technical Information of China (English)

Guodong Zhang; Wei Heng; Tian Liang; Chao Meng; Jinming Hu

2016-01-01

In order to enhance the efficiency of spectrum utilization and reduce communication overhead in spectrum sharing process,we propose a two-stage dynamic spectrum sharing scheme in which cooperative and noncooperative modes are analyzed in both stages.In particular,the existence and the uniqueness of Nash Equilibrium (NE) strategies for noncooperative mode are proved.In addition,a distributed iterative algorithm is proposed to obtain the optimal solutions of the scheme.Simulation studies are carried out to show the performance comparison between two modes as well as the system revenue improvement of the proposed scheme compared with a conventional scheme without a virtual price control factor.

Experimental studies of two-stage centrifugal dust concentrator

Science.gov (United States)

Vechkanova, M. V.; Fadin, Yu M.; Ovsyannikov, Yu G.

2018-03-01

The article presents data of experimental results of two-stage centrifugal dust concentrator, describes its design, and shows the development of a method of engineering calculation and laboratory investigations. For the experiments, the authors used quartz, ceramic dust and slag. Experimental dispersion analysis of dust particles was obtained by sedimentation method. To build a mathematical model of the process, dust collection was built using central composite rotatable design of the four factorial experiment. A sequence of experiments was conducted in accordance with the table of random numbers. Conclusion were made.

Opposed piston linear compressor driven two-stage Stirling Cryocooler for cooling of IR sensors in space application

Science.gov (United States)

Bhojwani, Virendra; Inamdar, Asif; Lele, Mandar; Tendolkar, Mandar; Atrey, Milind; Bapat, Shridhar; Narayankhedkar, Kisan

2017-04-01

A two-stage Stirling Cryocooler has been developed and tested for cooling IR sensors in space application. The concept uses an opposed piston linear compressor to drive the two-stage Stirling expander. The configuration used a moving coil linear motor for the compressor as well as for the expander unit. Electrical phase difference of 80 degrees was maintained between the voltage waveforms supplied to the compressor motor and expander motor. The piston and displacer surface were coated with Rulon an anti-friction material to ensure oil less operation of the unit. The present article discusses analysis results, features of the cryocooler and experimental tests conducted on the developed unit. The two-stages of Cryo-cylinder and the expander units were manufactured from a single piece to ensure precise alignment between the two-stages. Flexure bearings were used to suspend the piston and displacer about its mean position. The objective of the work was to develop a two-stage Stirling cryocooler with 2 W at 120 K and 0.5 W at 60 K cooling capacity for the two-stages and input power of less than 120 W. The Cryocooler achieved a minimum temperature of 40.7 K at stage 2.

Two Stage Fuzzy Methodology to Evaluate the Credit Risks of Investment Projects

OpenAIRE

O. Badagadze; G. Sirbiladze; I. Khutsishvili

2014-01-01

The work proposes a decision support methodology for the credit risk minimization in selection of investment projects. The methodology provides two stages of projects’ evaluation. Preliminary selection of projects with minor credit risks is made using the Expertons Method. The second stage makes ranking of chosen projects using the Possibilistic Discrimination Analysis Method. The latter is a new modification of a well-known Method of Fuzzy Discrimination Analysis.

Two stage heterotrophy/photoinduction culture of Scenedesmus incrassatulus: potential for lutein production.

Science.gov (United States)

Flórez-Miranda, Liliana; Cañizares-Villanueva, Rosa Olivia; Melchy-Antonio, Orlando; Martínez-Jerónimo, Fernando; Flores-Ortíz, Cesar Mateo

2017-11-20

A biomass production process including two stages, heterotrophy/photoinduction (TSHP), was developed to improve biomass and lutein production by the green microalgae Scenedesmus incrassatulus. To determine the effects of different nitrogen sources (yeast extract and urea) and temperature in the heterotrophic stage, experiments using shake flask cultures with glucose as the carbon source were carried out. The highest biomass productivity and specific pigment concentrations were reached using urea+vitamins (U+V) at 30°C. The first stage of the TSHP process was done in a 6L bioreactor, and the inductions in a 3L airlift photobioreactor. At the end of the heterotrophic stage, S. incrassatulus achieved the maximal biomass concentration, increasing from 7.22gL -1 to 17.98gL -1 with an increase in initial glucose concentration from 10.6gL -1 to 30.3gL -1 . However, the higher initial glucose concentration resulted in a lower specific growth rate (μ) and lower cell yield (Y x/s ), possibly due to substrate inhibition. After 24h of photoinduction, lutein content in S. incrassatulus biomass was 7 times higher than that obtained at the end of heterotrophic cultivation, and the lutein productivity was 1.6 times higher compared with autotrophic culture of this microalga. Hence, the two-stage heterotrophy/photoinduction culture is an effective strategy for high cell density and lutein production in S. incrassatulus. Copyright © 2017. Published by Elsevier B.V.

One-stage (Warsaw) and two-stage (Oslo) repair of unilateral cleft lip and palate: Craniofacial outcomes.

Science.gov (United States)

Fudalej, Piotr Stanislaw; Wegrodzka, Ewa; Semb, Gunvor; Hortis-Dzierzbicka, Maria

2015-09-01

The aim of this study was to compare facial development in subjects with complete unilateral cleft lip and palate (CUCLP) treated with two different surgical protocols. Lateral cephalometric radiographs of 61 patients (42 boys, 19 girls; mean age, 10.9 years; SD, 1) treated consecutively in Warsaw with one-stage repair and 61 age-matched and sex-matched patients treated in Oslo with two-stage surgery were selected to evaluate craniofacial morphology. On each radiograph 13 angular and two ratio variables were measured in order to describe hard and soft tissues of the facial region. The analysis showed that differences between the groups were limited to hard tissues – the maxillary prominence in subjects from the Warsaw group was decreased by almost 4° in comparison with the Oslo group (sella-nasion-A-point (SNA) = 75.3° and 79.1°, respectively) and maxillo-mandibular morphology was less favorable in the Warsaw group than the Oslo group (ANB angle = 0.8° and 2.8°, respectively). The soft tissue contour was comparable in both groups. In conclusion, inter-group differences suggest a more favorable outcome in the Oslo group. However, the distinctiveness of facial morphology in background populations (ie, in Poles and Norwegians) could have contributed to the observed results. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Electron-gun Evaporation of Cu and In thin Films as Precursors for CuInSe, Formation

International Nuclear Information System (INIS)

Caballero, R.; Guillen, C.

2001-01-01

In the present invigorations CuInSe, is obtained in two stages: sequential evaporation of Cu and In using an electron gun evaporator on substrates up to 30 x 30 cm 2 , and a posterior selenization of the deposited films. The study is mainly focused on the first stage, in where the control of the different evaporation parameters of the metal precursors is essential. Electrical measurements are carried out, and also the topography and the thickness are determined with the object of studying the properties and homogeneity of the thin films. (Author) 19 refs

A two-stage method for inverse medium scattering

KAUST Repository

Ito, Kazufumi

2013-03-01

We present a novel numerical method to the time-harmonic inverse medium scattering problem of recovering the refractive index from noisy near-field scattered data. The approach consists of two stages, one pruning step of detecting the scatterer support, and one resolution enhancing step with nonsmooth mixed regularization. The first step is strictly direct and of sampling type, and it faithfully detects the scatterer support. The second step is an innovative application of nonsmooth mixed regularization, and it accurately resolves the scatterer size as well as intensities. The nonsmooth model can be efficiently solved by a semi-smooth Newton-type method. Numerical results for two- and three-dimensional examples indicate that the new approach is accurate, computationally efficient, and robust with respect to data noise. © 2012 Elsevier Inc.

A two-stage metal valorisation process from electric arc furnace dust (EAFD

Directory of Open Access Journals (Sweden)

H. Issa

2016-04-01

Full Text Available This paper demonstrates possibility of separate zinc and lead recovery from coal composite pellets, composed of EAFD with other synergetic iron-bearing wastes and by-products (mill scale, pyrite-cinder, magnetite concentrate, through a two-stage process. The results show that in the first, low temp erature stage performed in electro-resistant furnace, removal of lead is enabled due to presence of chlorides in the system. In the second stage, performed at higher temperatures in Direct Current (DC plasma furnace, valorisation of zinc is conducted. Using this process, several final products were obtained, including a higher purity zinc oxide, which, by its properties, corresponds washed Waelz oxide.

A Two-stage DC-DC Converter for the Fuel Cell-Supercapacitor Hybrid System

DEFF Research Database (Denmark)

Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

2009-01-01

A wide input range multi-stage converter is proposed with the fuel cells and supercapacitors as a hybrid system. The front-end two-phase boost converter is used to optimize the output power and to reduce the current ripple of fuel cells. The supercapacitor power module is connected by push...... and designed. A 1kW prototype controlled by TMS320F2808 DSP is built in the lab. Simulation and experimental results confirm the feasibility of the proposed two stage dc-dc converter system.......-pull-forward half bridge (PPFHB) converter with coupled inductors in the second stage to handle the slow transient response of the fuel cells and realize the bidirectional power flow control. Moreover, this cascaded structure simplifies the power management. The control strategy for the whole system is analyzed...

Numerical simulation of brain tumor growth model using two-stage ...

African Journals Online (AJOL)

In the recent years, the study of glioma growth to be an active field of research Mathematical models that describe the proliferation and diffusion properties of the growth have been developed by many researchers. In this work, the performance analysis of two-stage Gauss-Seidel (TSGS) method to solve the glioma growth ...

On bi-criteria two-stage transportation problem: a case study

Directory of Open Access Journals (Sweden)

Ahmad MURAD

2010-01-01

Full Text Available The study of the optimum distribution of goods between sources and destinations is one of the important topics in projects economics. This importance comes as a result of minimizing the transportation cost, deterioration, time, etc. The classical transportation problem constitutes one of the major areas of application for linear programming. The aim of this problem is to obtain the optimum distribution of goods from different sources to different destinations which minimizes the total transportation cost. From the practical point of view, the transportation problems may differ from the classical form. It may contain one or more objective function, one or more stage to transport, one or more type of commodity with one or more means of transport. The aim of this paper is to construct an optimization model for transportation problem for one of mill-stones companies. The model is formulated as a bi-criteria two-stage transportation problem with a special structure depending on the capacities of suppliers, warehouses and requirements of the destinations. A solution algorithm is introduced to solve this class of bi-criteria two-stage transportation problem to obtain the set of non-dominated extreme points and the efficient solutions accompanied with each one that enables the decision maker to choose the best one. The solution algorithm mainly based on the fruitful application of the methods for treating transportation problems, theory of duality of linear programming and the methods of solving bi-criteria linear programming problems.

Solving crystal structures from powder data. I. The role of the prior information in the two-stage method

International Nuclear Information System (INIS)

Altomare, A.; Carrozzini, B.; Giacovazzo, C.; Guagliardi, A.; Moliterni, A.G.G.; Rizzi, R.

1996-01-01

For pt.II see ibid., p.674-81, 1996. The principal limitation of the diffraction methods for crystal structure analysis from powder data is originated by the collapse of the three-dimensional reciprocal space into the one dimension of the powder diffraction pattern. The degradation of the information can make difficult even the solution of small crystal structures and can generate inefficiencies in the least-squares methods devoted to crystal structure refinement. In this paper, the current two-stage procedures, the first stage dedicated to powder-pattern decomposition and the second to direct phasing of powder data, are analysed. It is shown that in the first stage such procedures disregard a large amount of information that can become available during the process of crystal structure solution and analysis. The use of such information is essential for making direct-methods procedures more robust and for improving the accuracy of the least-squares techniques. The performances of EXTRA [Altomare, Burla, Cascarano, Giacovazzo, Guagliardi, Moliterni and Polidori (1995). J. Appl. Cryst. 28, 842-846], a program for full-pattern decomposition based on the Le Bail algorithm, and of SIRPOW.92 [Altomare, Burla, Cascarano, Giacovazzo, Guagliardi, Polidori and Camalli (1994). J. Appl. Cryst. 27, 435-436], a direct-methods program optimized for powder data, are discussed in order to offer to the reader a logical pathway for the analysis of the traditional techniques and for the proposition of a new approach. It is shown that pattern-decomposition programs based on the Le Bail algorithm are able to exploit the prior information in a more effective way than Pawley-method-based decomposition programs. (orig.)

Two-stage single-volume exchange transfusion in severe hemolytic disease of the newborn.

Science.gov (United States)

Abbas, Wael; Attia, Nayera I; Hassanein, Sahar M A

2012-07-01

Evaluation of two-stage single-volume exchange transfusion (TSSV-ET) in decreasing the post-exchange rebound increase in serum bilirubin level, with subsequent reduction of the need for repeated exchange transfusions. The study included 104 neonates with hyperbilirubinemia needing exchange transfusion. They were randomly enrolled into two equal groups, each group comprised 52 neonates. TSSV-ET was performed for the 52 neonates and the traditional single-stage double-volume exchange transfusion (SSDV-ET) was performed to 52 neonates. TSSV-ET significantly lowered rebound serum bilirubin level (12.7 ± 1.1 mg/dL), compared to SSDV-ET (17.3 ± 1.7 mg/dL), p < 0.001. Need for repeated exchange transfusions was significantly lower in TSSV-ET group (13.5%), compared to 32.7% in SSDV-ET group, p < 0.05. No significant difference was found between the two groups as regards the morbidity (11.5% and 9.6%, respectively) and the mortality (1.9% for both groups). Two-stage single-volume exchange transfusion proved to be more effective in reducing rebound serum bilirubin level post-exchange and in decreasing the need for repeated exchange transfusions.

An inexact mixed risk-aversion two-stage stochastic programming model for water resources management under uncertainty.

Science.gov (United States)

Li, W; Wang, B; Xie, Y L; Huang, G H; Liu, L

2015-02-01

Uncertainties exist in the water resources system, while traditional two-stage stochastic programming is risk-neutral and compares the random variables (e.g., total benefit) to identify the best decisions. To deal with the risk issues, a risk-aversion inexact two-stage stochastic programming model is developed for water resources management under uncertainty. The model was a hybrid methodology of interval-parameter programming, conditional value-at-risk measure, and a general two-stage stochastic programming framework. The method extends on the traditional two-stage stochastic programming method by enabling uncertainties presented as probability density functions and discrete intervals to be effectively incorporated within the optimization framework. It could not only provide information on the benefits of the allocation plan to the decision makers but also measure the extreme expected loss on the second-stage penalty cost. The developed model was applied to a hypothetical case of water resources management. Results showed that that could help managers generate feasible and balanced risk-aversion allocation plans, and analyze the trade-offs between system stability and economy.

Two-stage heterotopic urethroplasty with usage of groin flap. Case report

Directory of Open Access Journals (Sweden)

R. T. Adamyan

2014-11-01

Full Text Available The article is devoted to the issues of struggle with problems of the urogenital region, arising as a consequence iatrogeny, with the help of plastic surgery. The article provides the case report, which deals with a two-step treatment of the patient with complete loss of the part of the urethra and bladder neck due to iatrogeny. The first stage of surgical treatment is the development of the artificial urethra formation by the rotation groin flap with the axis blood supply. The second stage is connection private urethra with artificial, with a heterotopic location of the lower urinary tract.

Two-Stage Fan I: Aerodynamic and Mechanical Design

Science.gov (United States)

Messenger, H. E.; Kennedy, E. E.

1972-01-01

A two-stage, highly-loaded fan was designed to deliver an overall pressure ratio of 2.8 with an adiabatic efficiency of 83.9 percent. At the first rotor inlet, design flow per unit annulus area is 42 lbm/sec/sq ft (205 kg/sec/sq m), hub/tip ratio is 0.4 with a tip diameter of 31 inches (0.787 m), and design tip speed is 1450 ft/sec (441.96 m/sec). Other features include use of multiple-circular-arc airfoils, resettable stators, and split casings over the rotor tip sections for casing treatment tests.

Two-stage commercial evaluation of engineering systems production projects for high-rise buildings

Science.gov (United States)

Bril, Aleksander; Kalinina, Olga; Levina, Anastasia

2018-03-01

The paper is devoted to the current and debatable problem of methodology of choosing the effective innovative enterprises for venture financing. A two-stage system of commercial innovation evaluation based on the UNIDO methodology is proposed. Engineering systems account for 25 to 40% of the cost of high-rise residential buildings. This proportion increases with the use of new construction technologies. Analysis of the construction market in Russia showed that the production of internal engineering systems elements based on innovative technologies has a growth trend. The production of simple elements is organized in small enterprises on the basis of new technologies. The most attractive for development is the use of venture financing of small innovative business. To improve the efficiency of these operations, the paper proposes a methodology for a two-stage evaluation of small business development projects. A two-stage system of commercial evaluation of innovative projects allows creating an information base for informed and coordinated decision-making on venture financing of enterprises that produce engineering systems elements for the construction business.

Two-stage commercial evaluation of engineering systems production projects for high-rise buildings

Directory of Open Access Journals (Sweden)

Bril Aleksander

2018-01-01

Full Text Available The paper is devoted to the current and debatable problem of methodology of choosing the effective innovative enterprises for venture financing. A two-stage system of commercial innovation evaluation based on the UNIDO methodology is proposed. Engineering systems account for 25 to 40% of the cost of high-rise residential buildings. This proportion increases with the use of new construction technologies. Analysis of the construction market in Russia showed that the production of internal engineering systems elements based on innovative technologies has a growth trend. The production of simple elements is organized in small enterprises on the basis of new technologies. The most attractive for development is the use of venture financing of small innovative business. To improve the efficiency of these operations, the paper proposes a methodology for a two-stage evaluation of small business development projects. A two-stage system of commercial evaluation of innovative projects allows creating an information base for informed and coordinated decision-making on venture financing of enterprises that produce engineering systems elements for the construction business.

Initial Clinical Experience in Multiple Myeloma Staging by Means of Whole-Body Resonance Techniques

International Nuclear Information System (INIS)

Gallego, J. I.; Concepcion, L.; Alonso, S.; Sanchez, B.; Manzi, F.

2003-01-01

To develop a magnetic resonance (MR) exploratory technique equivalent to serial bone X-ray, and to compare their precision in the staging of multiple myeloma (MM) patients. Multiple acquisition T1-weights TSE and STIR sequences in the coronal plane were performed. Ten healthy volunteers and 11 multiple myeloma diagnosed patients were included. The visualization of bony structures was particularly noted,with special attention given to those which would normally be included in a serial bone X-ray. In the case of the patients, a comparison was made between diagnostic capacities of the MR sequences. MR highlighters significantly more (p<0.05) bony elements than did the serial bone X-ray. This was greatly due to a sequential displacement of the scanner bed, allowing for field-of-views which were minimally from head to third proximal of the leg. Magnetic resonance detected a significantly higher number (p<0.05) of lesions. It was, in turn, capable of revealing greater lesion extensions, even to the point of implying staging classification changes in 18% of the patients. The utilization of whole-body MR techniques in multiple myeloma patients is feasible and clinically beneficial. MR is both more sensitive and more specific than serial bone X-ray for evaluation of bony lesions in MM. It is currently serving as a valid alternative in a growing numbers of patients. (Author) 10 refs

Quick pace of property acquisitions requires two-stage evaluations

International Nuclear Information System (INIS)

Hollo, R.; Lockwood, S.

1994-01-01

The traditional method of evaluating oil and gas reserves may be too cumbersome for the quick pace of oil and gas property acquisition. An acquisition evaluator must decide quickly if a property meets basic purchase criteria. The current business climate requires a two-stage approach. First, the evaluator makes a quick assessment of the property and submits a bid. If the bid is accepted then the evaluator goes on with a detailed analysis, which represents the second stage. Acquisition of producing properties has become an important activity for many independent oil and gas producers, who must be able to evaluate reserves quickly enough to make effective business decisions yet accurately enough to avoid costly mistakes. Independent thus must be familiar with how transactions usually progress as well as with the basic methods of property evaluation. The paper discusses acquisition activity, the initial offer, the final offer, property evaluation, and fair market value

Comparing radiation exposure during percutaneous vertebroplasty using one- vs. two-fluoroscopic technique

Directory of Open Access Journals (Sweden)

Li Yen-Yao

2013-01-01

Full Text Available Abstract Background Percutaneous vertebroplasty (PV requires relatively lengthy fluoroscopic guidance, which might lead to substantial radiation exposure to patients or operators. The two-fluoroscopic technique (two-plane radiographs obtained using two fluoroscopes during PV can provide simultaneous two-planar projections with reducing operative time. However, the two-fluoroscopic technique may expose the operator or patient to increased radiation dose. The aim of this study was to quantify the amount of radiation exposure to the patient or operator that occurs during PV using one- vs. two-fluoroscopic technique. Methods Two radiation dosimeters were placed on the right flank of each patient and on the upper sternum of each operator during 26 single-level PV procedures by one senior surgeon. The use of two-fluoroscopic technique (13 patients and one-fluoroscopic technique (13 patients were allocated in a consecutive and alternative manner. The operative time and mean radiation dose to each patient and operator were monitored and compared between groups. Results Mean radiation dose to the patient was 1.97 ± 1.20 mSv (95% CI, 0.71 to 3.23 for the one-fluoroscopic technique group vs. 0.95 ± 0.34 mSv (95% CI, 0.85 to 1.23 for the two-fluoroscopic technique group (P =0.031. Mean radiation dose to the operator was 0.27 ± 0.12 mSv (95% CI, 0.17–0.56 for the one-fluoroscopic technique group vs. 0.25 ± 0.14 mSv (95% CI, 0.06–0.44 for the two-fluoroscopic technique group (P = 0.653. The operative time was significantly different between groups: 47.15 ± 13.48 min (range, 20–75 for the one-fluoroscopic technique group vs. 36.62 ± 8.42 min (range, 21–50 for the two-fluoroscopic technique group (P =0.019. Conclusion Compared to the one-fluoroscopic technique, the two-fluoroscopic technique used during PV provides not only shorter operative times but also reduces the radiation exposure to the patient. There was no

Enhancing the hydrolysis process of a two-stage biogas technology for the organic fraction of municipal solid waste

DEFF Research Database (Denmark)

Nasir, Zeeshan; Uellendahl, Hinrich

2015-01-01

The Danish company Solum A/S has developed a two-stage dry anaerobic digestion process labelled AIKAN® for the biological conversion of the organic fraction of municipal solid waste (OFMSW) into biogas and compost. In the AIKAN® process design the methanogenic (2nd) stage is separated from...... the hydrolytic (1st) stage, which enables pump-free feeding of the waste into the 1st stage (processing module), and eliminates the risk for blocking of pumps and pipes by pumping only the percolate from the 1st stage into the 2nd stage (biogas reactor tank). The biogas yield of the AIKAN® two-stage process......, however, has shown to be only about 60% of the theoretical maximum. Previous monitoring of the hydrolytic and methanogenic activity in the two stages of the process revealed that the bottleneck of the whole degradation process is rather found in the hydrolytic first stage while the methanogenic second...

Two-stage combustion for reducing pollutant emissions from gas turbine combustors

Science.gov (United States)

Clayton, R. M.; Lewis, D. H.

1981-01-01

Combustion and emission results are presented for a premix combustor fueled with admixtures of JP5 with neat H2 and of JP5 with simulated partial-oxidation product gas. The combustor was operated with inlet-air state conditions typical of cruise power for high performance aviation engines. Ultralow NOx, CO and HC emissions and extended lean burning limits were achieved simultaneously. Laboratory scale studies of the non-catalyzed rich-burning characteristics of several paraffin-series hydrocarbon fuels and of JP5 showed sooting limits at equivalence ratios of about 2.0 and that in order to achieve very rich sootless burning it is necessary to premix the reactants thoroughly and to use high levels of air preheat. The application of two-stage combustion for the reduction of fuel NOx was reviewed. An experimental combustor designed and constructed for two-stage combustion experiments is described.

A cause and effect two-stage BSC-DEA method for measuring the relative efficiency of organizations

Directory of Open Access Journals (Sweden)

Seyed Esmaeel Najafi

2011-01-01

Full Text Available This paper presents an integration of balanced score card (BSE with two-stage data envelopment analysis (DEA. The proposed model of this paper uses different financial and non-financial perspectives to evaluate the performance of decision making units in different BSC stages. At each stage, a two-stage DEA method is implemented to measure the relative efficiency of decision making units and the results are monitored using the cause and effect relationships. An empirical study for a banking sector is also performed using the method developed in this paper and the results are briefly analyzed.

Ground-based intercomparison of two isoprene measurement techniques

Directory of Open Access Journals (Sweden)

E. Leibrock

2003-01-01

Full Text Available An informal intercomparison of two isoprene (C5H8 measurement techniques was carried out during Fall of 1998 at a field site located approximately 3 km west of Boulder, Colorado, USA. A new chemical ionization mass spectrometric technique (CIMS was compared to a well-established gas chromatographic technique (GC. The CIMS technique utilized benzene cation chemistry to ionize isoprene. The isoprene levels measured by the CIMS were often larger than those obtained with the GC. The results indicate that the CIMS technique suffered from an anthropogenic interference associated with air masses from the Denver, CO metropolitan area as well as an additional interference occurring in clean conditions. However, the CIMS technique is also demonstrated to be sensitive and fast. Especially after introduction of a tandem mass spectrometric technique, it is therefore a candidate for isoprene measurements in remote environments near isoprene sources.

Lower rectal cancer. Preoperative staging with CT air enema technique

International Nuclear Information System (INIS)

Kanazawa, Amane; Fujii, Shouichi; Iwata, Seiichirou

2009-01-01

Preoperative assessment of rectal cancer wall invasion is an important indication of the need for lateral side wall dissection. The purpose of this study was to determine the accuracy rates and clinical usefulness of air-enema CT in preoperative staging of lower rectal cancer. A total of 88 patients diagnosed with lower rectal cancer were examined with an air-enema CT preoperatively and had surgical resection performed. One group was T1-T2 while the other was T3-T4. Forty-two patients were T1-T2, and 46 patients were T3-T4. In univariate and multivariate analysis, irregularities of the rectal wall and spiculated appearance of the rectal wall were significant predictive factors in T3-T4. In patients with air-enema CT findings of rectal wall irregularities and speculated appearance, the accuracy rate for detecting T3-T4 was 85.2-86.45 percent. These results show that air-enema CT is useful for determining the preoperative staging of lower rectal cancer and indication of the need for lateral side wall dissection. (author)

A two staged condensation of vapors of an isobutane tower in installations for sulfuric acid alkylation

Energy Technology Data Exchange (ETDEWEB)

Smirnov, N.P.; Feyzkhanov, R.I.; Idrisov, A.D.; Navalikhin, P.G.; Sakharov, V.D.

1983-01-01

In order to increase the concentration of isobutane to greater than 72 to 76 percent in an installation for sulfuric acid alkylation, a system of two staged condensation of vapors from an isobutane tower is placed into operation. The first stage condenses the heavier part of the upper distillate of the tower, which is achieved through somewhat of an increase in the condensate temperature. The product which is condensed in the first stage is completely returned to the tower as a live irrigation. The vapors of the isobutane fraction which did not condense in the first stage are sent to two newly installed condensers, from which the product after condensation passes through intermediate tanks to further depropanization. The two staged condensation of vapors of the isobutane tower reduces the content of the inert diluents, the propane and n-butane in the upper distillate of the isobutane tower and creates more favorable conditions for the operation of the isobutane and propane tower.

A novel two-stage evaluation system based on a Group-G1 approach to identify appropriate emergency treatment technology schemes in sudden water source pollution accidents.

Science.gov (United States)

Qu, Jianhua; Meng, Xianlin; Hu, Qi; You, Hong

2016-02-01

Sudden water source pollution resulting from hazardous materials has gradually become a major threat to the safety of the urban water supply. Over the past years, various treatment techniques have been proposed for the removal of the pollutants to minimize the threat of such pollutions. Given the diversity of techniques available, the current challenge is how to scientifically select the most desirable alternative for different threat degrees. Therefore, a novel two-stage evaluation system was developed based on a circulation-correction improved Group-G1 method to determine the optimal emergency treatment technology scheme, considering the areas of contaminant elimination in both drinking water sources and water treatment plants. In stage 1, the threat degree caused by the pollution was predicted using a threat evaluation index system and was subdivided into four levels. Then, a technique evaluation index system containing four sets of criteria weights was constructed in stage 2 to obtain the optimum treatment schemes corresponding to the different threat levels. The applicability of the established evaluation system was tested by a practical cadmium-contaminated accident that occurred in 2012. The results show this system capable of facilitating scientific analysis in the evaluation and selection of emergency treatment technologies for drinking water source security.

One-stage vs two-stage cartilage repair: a current review

Directory of Open Access Journals (Sweden)

Daniel Meyerkort

2010-10-01

Full Text Available Daniel Meyerkort, David Wood, Ming-Hao ZhengCenter for Orthopaedic Research, School of Surgery and Pathology, University of Western Australia, Perth, AustraliaIntroduction: Articular cartilage has a poor capacity for regeneration if damaged. Various methods have been used to restore the articular surface, improve pain, function, and slow progression to osteoarthritis.Method: A PubMed review was performed on 18 March, 2010. Search terms included “autologous chondrocyte implantation (ACI” and “microfracture” or “mosaicplasty”. The aim of this review was to determine if 1-stage or 2-stage procedures for cartilage repair produced different functional outcomes.Results: The main procedures currently used are ACI and microfracture. Both first-generation ACI and microfracture result in clinical and functional improvement with no significant differences. A significant increase in functional outcome has been observed in second-generation procedures such as Hyalograft C, matrix-induced ACI, and ChondroCelect compared with microfracture. ACI results in a higher percentage of patients with clinical improvement than mosaicplasty; however, these results may take longer to achieve.Conclusion: Clinical and functional improvements have been demonstrated with ACI, microfracture, mosaicplasty, and synthetic cartilage constructs. Heterogeneous products and lack of good-quality randomized-control trials make product comparison difficult. Future developments involve scaffolds, gene therapy, growth factors, and stem cells to create a single-stage procedure that results in hyaline articular cartilage.Keywords: autologous chondrocyte implantation, microfracture, cartilage repair

Design and control of a decoupled two degree of freedom translational parallel micro-positioning stage.

Science.gov (United States)

Lai, Lei-Jie; Gu, Guo-Ying; Zhu, Li-Min

2012-04-01

This paper presents a novel decoupled two degrees of freedom (2-DOF) translational parallel micro-positioning stage. The stage consists of a monolithic compliant mechanism driven by two piezoelectric actuators. The end-effector of the stage is connected to the base by four independent kinematic limbs. Two types of compound flexure module are serially connected to provide 2-DOF for each limb. The compound flexure modules and mirror symmetric distribution of the four limbs significantly reduce the input and output cross couplings and the parasitic motions. Based on the stiffness matrix method, static and dynamic models are constructed and optimal design is performed under certain constraints. The finite element analysis results are then given to validate the design model and a prototype of the XY stage is fabricated for performance tests. Open-loop tests show that maximum static and dynamic cross couplings between the two linear motions are below 0.5% and -45 dB, which are low enough to utilize the single-input-single-out control strategies. Finally, according to the identified dynamic model, an inversion-based feedforward controller in conjunction with a proportional-integral-derivative controller is applied to compensate for the nonlinearities and uncertainties. The experimental results show that good positioning and tracking performances are achieved, which verifies the effectiveness of the proposed mechanism and controller design. The resonant frequencies of the loaded stage at 2 kg and 5 kg are 105 Hz and 68 Hz, respectively. Therefore, the performance of the stage is reasonably good in term of a 200 N load capacity. © 2012 American Institute of Physics

Two-stage decision approach to material accounting

International Nuclear Information System (INIS)

Opelka, J.H.; Sutton, W.B.

1982-01-01

The validity of the alarm threshold 4sigma has been checked for hypothetical large and small facilities using a two-stage decision model in which the diverter's strategic variable is the quantity diverted, and the defender's strategic variables are the alarm threshold and the effectiveness of the physical security and material control systems in the possible presence of a diverter. For large facilities, the material accounting system inherently appears not to be a particularly useful system for the deterrence of diversions, and essentially no improvement can be made by lowering the alarm threshold below 4sigma. For small facilities, reduction of the threshold to 2sigma or 3sigma is a cost effective change for the accounting system, but is probably less cost effective than making improvements in the material control and physical security systems

Two stages of Kondo effect and competition between RKKY and Kondo in Gd-based intermetallic compound

International Nuclear Information System (INIS)

Vaezzadeh, Mehdi; Yazdani, Ahmad; Vaezzadeh, Majid; Daneshmand, Gissoo; Kanzeghi, Ali

2006-01-01

The magnetic behavior of Gd-based intermetallic compound (Gd 2 Al (1-x) Au x ) in the form of the powder and needle, is investigated. All the samples are an orthorhombic crystal structure. Only the compound with x=0.4 shows the Kondo effect (other compounds have a normal behavior). Although, for the compound in the form of powder, with x=0.4, the susceptibility measurement χ(T) shows two different stages. Moreover for (T>T K2 ) a fall of the value of χ(T) is observable, which indicates a weak presence of ferromagnetic phase. About the two stages of Kondo effect, we observe at the first (T K1 ) an increase of χ(T) and in the second stage (T K2 ) a new remarkable decrease of χ(T) (T K1 >T K2 ). For the sample in the form of needles, the first stage is observable only under high magnetic field. This first stage could be corresponds to a narrow resonance between Kondo cloud and itinerant electron. The second stage, which is remarkably visible for the sample in the form of the powder, can be attribute to a complete polarization of Kondo cloud. Observation of these two Kondo stages could be due to the weak presence of RKKY contribution

Operation of a two-stage continuous fermentation process producing hydrogen and methane from artificial food wastes

Energy Technology Data Exchange (ETDEWEB)

Nagai, Kohki; Mizuno, Shiho; Umeda, Yoshito; Sakka, Makiko [Toho Gas Co., Ltd. (Japan); Osaka, Noriko [Tokyo Gas Co. Ltd. (Japan); Sakka, Kazuo [Mie Univ. (Japan)

2010-07-01

An anaerobic two-stage continuous fermentation process with combined thermophilic hydrogenogenic and methanogenic stages (two-stage fermentation process) was applied to artificial food wastes on a laboratory scale. In this report, organic loading rate (OLR) conditions for hydrogen fermentation were optimized before operating the two-stage fermentation process. The OLR was set at 11.2, 24.3, 35.2, 45.6, 56.1, and 67.3 g-COD{sub cr} L{sup -1} day{sup -1} with a temperature of 60 C, pH5.5 and 5.0% total solids. As a result, approximately 1.8-2.0 mol-H{sub 2} mol-hexose{sup -1} was obtained at the OLR of 11.2-56.1 g-COD{sub cr} L{sup -1} day{sup -1}. In contrast, it was inferred that the hydrogen yield at the OLR of 67.3 g-COD{sub cr} L{sup -1} day{sup -1} decreased because of an increase in lactate concentration in the culture medium. The performance of the two-stage fermentation process was also evaluated over three months. The hydraulic retention time (HRT) of methane fermentation was able to be shortened 5.0 days (under OLR 12.4 g-COD{sub cr} L{sup -1} day{sup -1} conditions) when the OLR of hydrogen fermentation was 44.0 g-COD{sub cr} L{sup -1} day{sup -1}, and the average gasification efficiency of the two-stage fermentation process was 81% at the time. (orig.)

Insufficient sensitivity of joint aspiration during the two-stage exchange of the hip with spacers.

Science.gov (United States)

Boelch, Sebastian Philipp; Weissenberger, Manuel; Spohn, Frederik; Rudert, Maximilian; Luedemann, Martin

2018-01-10

Evaluation of infection persistence during the two-stage exchange of the hip is challenging. Joint aspiration before reconstruction is supposed to rule out infection persistence. Sensitivity and specificity of synovial fluid culture and synovial leucocyte count for detecting infection persistence during the two-stage exchange of the hip were evaluated. Ninety-two aspirations before planned joint reconstruction during the two-stage exchange with spacers of the hip were retrospectively analyzed. The sensitivity and specificity of synovial fluid culture was 4.6 and 94.3%. The sensitivity and specificity of synovial leucocyte count at a cut-off value of 2000 cells/μl was 25.0 and 96.9%. C-reactive protein (CRP) and erythrocyte sedimentation rate (ESR) values were significantly higher before prosthesis removal and reconstruction or spacer exchange (p = 0.00; p = 0.013 and p = 0.039; p = 0.002) in the infection persistence group. Receiver operating characteristic area under the curve values before prosthesis removal and reconstruction or spacer exchange for ESR were lower (0.516 and 0.635) than for CRP (0.720 and 0.671). Synovial fluid culture and leucocyte count cannot rule out infection persistence during the two-stage exchange of the hip.

Sectional Fixed Orthodontic Extrusion Technique in Management of Teeth with Complicated Crown-Root Fractures: Report of Two Cases

Directory of Open Access Journals (Sweden)

S. Nagarajan M. P. Sockalingam

2018-01-01

Full Text Available Complicated crown-root fractures account for a small percentage of traumatic dental injuries seen in children; however, management of these injuries can be very challenging to clinicians. Factors such as complexity of the injury, patient’s age and dentition stage, patient’s cooperation, and parental demands may have some bearing on the type of treatment undertaken and its outcomes. In some children, these injuries may have significant impact on their quality of life. The purpose of this article is to describe two cases of complicated crown-root fracture which were successfully managed through orthodontic extrusion using a sectional fixed orthodontic technique. The basis for the treatment technique and its favourable outcomes were highlighted with its advantages and drawbacks.

Two-stage soil infiltration treatment system for treating ammonium wastewaters of low COD/TN ratios.

Science.gov (United States)

Lei, Zhongfang; Wu, Ting; Zhang, Yi; Liu, Xiang; Wan, Chunli; Lee, Duu-Jong; Tay, Joo-Hwa

2013-01-01

Soil infiltration treatment (SIT) is ineffective to treat ammonium wastewaters of total nitrogen (TN) > 100 mg l(-1). This study applied a novel two-stage SIT process for effective TN removal from wastewaters of TN>100 mg l(-1) and of chemical oxygen demand (COD)/TN ratio of 3.2-8.6. The wastewater was first fed into the soil column (stage 1) at hydraulic loading rate (HLR) of 0.06 m(3) m(-2) d(-1) for COD removal and total phosphorus (TP) immobilization. Then the effluent from stage 1 was fed individually into four soil columns (stage 2) at 0.02 m(3) m(-2) d(-1) of HLR with different proportions of raw wastewater as additional carbon source. Over the one-year field test, balanced nitrification and denitrification in the two-stage SIT revealed excellent TN removal (>90%) from the tested wastewaters. Copyright © 2012 Elsevier Ltd. All rights reserved.

High-speed double-disc TMP [thermomechanical pulp] from northern and southern softwoods: One or two refining stages

Energy Technology Data Exchange (ETDEWEB)

Sabourin, M.J. (Andritz Sprout-Bauer, Inc., Springfield, OH (United States)); Cort, J.B.; Musselman, R.L. (Andritz Sprout-Bauer, Inc., Muncy, PA (United States))

1994-01-01

Pilot-plant studies were carried out to evaluate one- and two-stage high-speed refining processes for production of thermomechanical pulp (TMP) at minimal energy consumption. Both northern (black spruce/balsam fir) and southern (lobolly pine) wood species were tested. Preliminary results indicate both one- and two-stage high-speed refining are suitable for the production of TMP from spruce and fir. Single-stage, high-speed refining of spruce/fir resulted in over 25% energy savings compared to conventional TMP production. The resulting TMP had improved optical and shive content properties, with slightly reduced pulp strength and long fiber content. Two stages of refining were necessary to optimize pulp quality from the lobolly pine furnish. A 15% energy reduction was obtained when comparing high-speed and conventional TMP pulping of lobolly pine at similar operating conditions. The high-speed pine TMP had comparable bonding strength, shive content, and lower tear than conventional two-stage lobolly pine TMP. 14 refs., 11 figs., 6 tabs.

Silicone infusion tubing instead of Hunter rods for two-stage zone 2 flexor tendon reconstruction in a resource-limited surgical environment.

Science.gov (United States)

Kibadi, K; Moutet, F

2017-10-01

The authors describe their experience using silicone infusion tubing in place of Hunter rods for two-stage zone 2 flexor tendon reconstruction in a resource-limited surgical environment. This case report features a 47-year-old, right-handed man who had no active PIP and DIP joint flexion in four fingers of the right hand 5 months after an injury. During the first repair stage, the A2 and A4 pulleys were reconstructed using an extensor retinaculum graft. An infusion tube was inserted instead of Hunter rods. During the second stage, formation of a digital neo-canal around the infusion tubing was observed. The infusion tubing was removed and replaced with a palmaris longus tendon graft according to the conventional technique. Physiotherapy and rehabilitation followed surgery. At 6 months, very significant progress had been made with complete recovery of PIP and DIP flexion in the four fingers. Copyright © 2017 SFCM. Published by Elsevier Masson SAS. All rights reserved.

A two-stage stochastic programming approach for operating multi-energy systems

DEFF Research Database (Denmark)

Zeng, Qing; Fang, Jiakun; Chen, Zhe

2017-01-01

This paper provides a two-stage stochastic programming approach for joint operating multi-energy systems under uncertainty. Simulation is carried out in a test system to demonstrate the feasibility and efficiency of the proposed approach. The test energy system includes a gas subsystem with a gas...

Combined Multi-criteria Evaluation Stage Technique as an Agro Waste Evaluation Indicator for Polymeric Composites: Date Palm Fibers as a Case Study

Directory of Open Access Journals (Sweden)

Faris M. AL-Oqla

2014-06-01

Full Text Available The final features of natural fiber composites (NFCs depend on the integrated characteristics of their constituents. In the industry today, natural agro waste fibers are evaluated using a limited number of criteria. In this work, a combined multi-criteria evaluation stage technique (CMCEST is introduced as a simple efficient systematic indicator to enhance evaluation of the available natural agro wastes for polymeric composites. In this proposed technique, criteria affecting the proper selection of natural agro waste fibers were combined and divided into sequence stages as follows: single-evaluation-criterion (SEC, combined-double-evaluation-criterion (CDEC, combined-triple-evaluation-criterion (CTEC, etc. These stages are based on combined physical, mechanical, and economic evaluation criteria and can be extended to several further stages to include other beneficial characteristics. The effectiveness of this technique was demonstrated by evaluating coir, date palm, jute, hemp, kenaf, and oil palm fibers simultaneously. This combined evaluation criteria can lead to more informative decisions regarding selection of the most suitable fiber type for polymeric composites. The CMCEST enhancements can reveal new potential fiber types through better evaluation schemes, help achieve clearer indications of the capabilities of available agro wastes to enhance composites, and determine proper ecological waste management practices. Utilizing the proposed technique, the date palm fiber type was found to be quite promising due to beneficial characteristics revealed in CTEC, which provides a reasonable, cheap, and eco-friendly alternative material suitable for different applications.

A two-stage procedure for determining unsaturated hydraulic characteristics using a syringe pump and outflow observations

DEFF Research Database (Denmark)

Wildenschild, Dorthe; Jensen, Karsten Høgh; Hollenbeck, Karl-Josef

1997-01-01

A fast two-stage methodology for determining unsaturated flow characteristics is presented. The procedure builds on direct measurement of the retention characteristic using a syringe pump technique, combined with inverse estimation of the hydraulic conductivity characteristic based on one......-step outflow experiments. The direct measurements are obtained with a commercial syringe pump, which continuously withdraws fluid from a soil sample at a very low and accurate how rate, thus providing the water content in the soil sample. The retention curve is then established by simultaneously monitoring......-step outflow data and the independently measured retention data are included in the objective function of a traditional least-squares minimization routine, providing unique estimates of the unsaturated hydraulic characteristics by means of numerical inversion of Richards equation. As opposed to what is often...

Glaucoma in modified osteo-odonto-keratoprosthesis eyes: role of additional stage 1A and Ahmed glaucoma drainage device-technique and timing.

Science.gov (United States)

Iyer, Geetha; Srinivasan, Bhaskar; Agarwal, Shweta; Shetty, Roshni; Krishnamoorthy, Sripriya; Balekudaru, Shantha; Vijaya, Lingam

2015-03-01

To report the technique, timing, and outcomes of the Ahmed glaucoma drainage device in eyes with the modified osteo-odonto-keratoprosthesis (MOOKP) and the role of an additional stage 1A to the Rome-Vienna protocol. Retrospective interventional case series. Case records of 22 eyes of 20 patients with high intraocular pressure at various stages of the MOOKP procedure performed in 85 eyes of 82 patients were studied. Stage 1A, which includes total iridodialysis, intracapsular cataract extraction, and anterior vitrectomy, was done in all eyes as the primary stage. Seventeen Ahmed glaucoma drainage devices were implanted in 15 eyes of 14 patients (chemical injury in 9 [10 eyes] and Stevens-Johnson syndrome in 5 patients). Implantation was performed during and after stage 1A in 2 and 7 eyes, respectively, after stage 1B+1C in 1 eye, and after stage 2 in 6 eyes. Eleven of 15 eyes (73.3%) remained stable with adequate control of intraocular pressure over a mean follow-up period of 33.68 months (1-90 months). Complications related to the drainage device were hypotony in 1 eye and vitreous block of the tube in 1 eye. It is ideal to place the Ahmed glaucoma drainage device prior to the mucosal graft when the anatomy of the ocular surface is least altered with best outcomes. The technique of placement of the drainage device during the various stages of the MOOKP procedure has been described. The intraocular pressure stabilized in three quarters of the eyes with pre-existing glaucoma. Copyright © 2015 Elsevier Inc. All rights reserved.

Two-stage categorization in brand extension evaluation: electrophysiological time course evidence.

Directory of Open Access Journals (Sweden)

Qingguo Ma

Full Text Available A brand name can be considered a mental category. Similarity-based categorization theory has been used to explain how consumers judge a new product as a member of a known brand, a process called brand extension evaluation. This study was an event-related potential study conducted in two experiments. The study found a two-stage categorization process reflected by the P2 and N400 components in brand extension evaluation. In experiment 1, a prime-probe paradigm was presented in a pair consisting of a brand name and a product name in three conditions, i.e., in-category extension, similar-category extension, and out-of-category extension. Although the task was unrelated to brand extension evaluation, P2 distinguished out-of-category extensions from similar-category and in-category ones, and N400 distinguished similar-category extensions from in-category ones. In experiment 2, a prime-probe paradigm with a related task was used, in which product names included subcategory and major-category product names. The N400 elicited by subcategory products was more significantly negative than that elicited by major-category products, with no salient difference in P2. We speculated that P2 could reflect the early low-level and similarity-based processing in the first stage, whereas N400 could reflect the late analytic and category-based processing in the second stage.

Possible two-stage /sup 87/Sr evolution in the Stockdale Rhyolite

Energy Technology Data Exchange (ETDEWEB)

Compston, W.; McDougall, I. (Australian National Univ., Canberra. Research School of Earth Sciences); Wyborn, D. (Department of Minerals and Energy, Canberra (Australia). Bureau of Mineral Resources)

1982-12-01

The Rb-Sr total-rock data for the Stockdale Rhyolite, of significance for the Palaeozoic time scale, are more scattered about a single-stage isochron than expected from experimental error. Two-stage /sup 87/Sr evolution for several of the samples is explored to explain this, as an alternative to variation in the initial /sup 87/Sr//sup 86/Sr which is customarily used in single-stage dating models. The deletion of certain samples having very high Rb/Sr removes most of the excess scatter and leads to an estimate of 430 +- 7 m.y. for the age of extrusion. There is a younger alignment of Rb-Sr data within each sampling site at 412 +- 7 m.y. We suggest that the Stockdale Rhyolite is at least 430 m.y. old, that its original range in Rb/Sr was smaller than now observed, and that it experienced a net loss in Sr during later hydrothermal alteration at ca. 412 m.y.

Modelling of an air-cooled two-stage Rankine cycle for electricity production

International Nuclear Information System (INIS)

Liu, Bo

2014-01-01

This work considers a two stage Rankine cycle architecture slightly different from a standard Rankine cycle for electricity generation. Instead of expanding the steam to extremely low pressure, the vapor leaves the turbine at a higher pressure then having a much smaller specific volume. It is thus possible to greatly reduce the size of the steam turbine. The remaining energy is recovered by a bottoming cycle using a working fluid which has a much higher density than the water steam. Thus, the turbines and heat exchangers are more compact; the turbine exhaust velocity loss is lower. This configuration enables to largely reduce the global size of the steam water turbine and facilitate the use of a dry cooling system. The main advantage of such an air cooled two stage Rankine cycle is the possibility to choose the installation site of a large or medium power plant without the need of a large and constantly available water source; in addition, as compared to water cooled cycles, the risk regarding future operations is reduced (climate conditions may affect water availability or temperature, and imply changes in the water supply regulatory rules). The concept has been investigated by EDF R and D. A 22 MW prototype was developed in the 1970's using ammonia as the working fluid of the bottoming cycle for its high density and high latent heat. However, this fluid is toxic. In order to search more suitable working fluids for the two stage Rankine cycle application and to identify the optimal cycle configuration, we have established a working fluid selection methodology. Some potential candidates have been identified. We have evaluated the performances of the two stage Rankine cycles operating with different working fluids in both design and off design conditions. For the most acceptable working fluids, components of the cycle have been sized. The power plant concept can then be evaluated on a life cycle cost basis. (author)

A Two-Stage Layered Mixture Experiment Design for a Nuclear Waste Glass Application-Part 1

International Nuclear Information System (INIS)

Cooley, Scott K.; Piepel, Gregory F.; Gan, Hao; Kot, Wing; Pegg, Ian L.

2003-01-01

A layered experimental design involving mixture variables was generated to support developing property-composition models for high-level waste (HLW) glasses. The design was generated in two stages, each having unique characteristics. Each stage used a layered design having an outer layer, an inner layer, a center point, and some replicates. The layers were defined by single- and multi-variable constraints. The first stage involved 15 glass components treated as mixture variables. For each layer, vertices were generated and optimal design software was used to select alternative subsets of vertices and calculate design optimality measures. Two partial quadratic mixture models, containing 25 terms for the outer layer and 30 terms for the inner layer, were the basis for the optimal design calculations. Distributions of predicted glass property values were plotted and evaluated for the alternative subsets of vertices. Based on the optimality measures and the predicted property distributions, a ''best'' subset of vertices was selected for each layer to form a layered design for the first stage. The design for the second stage was selected to augment the first-stage design. The discussion of the second-stage design begins in this Part 1 and is continued in Part 2 (Cooley and Piepel, 2003b)

Two-Stage Performance Engineering of Container-based Virtualization

Directory of Open Access Journals (Sweden)

Zheng Li

2018-02-01

Full Text Available Cloud computing has become a compelling paradigm built on compute and storage virtualization technologies. The current virtualization solution in the Cloud widely relies on hypervisor-based technologies. Given the recent booming of the container ecosystem, the container-based virtualization starts receiving more attention for being a promising alternative. Although the container technologies are generally considered to be lightweight, no virtualization solution is ideally resource-free, and the corresponding performance overheads will lead to negative impacts on the quality of Cloud services. To facilitate understanding container technologies from the performance engineering’s perspective, we conducted two-stage performance investigations into Docker containers as a concrete example. At the first stage, we used a physical machine with “just-enough” resource as a baseline to investigate the performance overhead of a standalone Docker container against a standalone virtual machine (VM. With findings contrary to the related work, our evaluation results show that the virtualization’s performance overhead could vary not only on a feature-by-feature basis but also on a job-to-job basis. Moreover, the hypervisor-based technology does not come with higher performance overhead in every case. For example, Docker containers particularly exhibit lower QoS in terms of storage transaction speed. At the ongoing second stage, we employed a physical machine with “fair-enough” resource to implement a container-based MapReduce application and try to optimize its performance. In fact, this machine failed in affording VM-based MapReduce clusters in the same scale. The performance tuning results show that the effects of different optimization strategies could largely be related to the data characteristics. For example, LZO compression can bring the most significant performance improvement when dealing with text data in our case.

Forensic age estimation based on magnetic resonance imaging of third molars: converting 2D staging into 3D staging.

Science.gov (United States)

De Tobel, Jannick; Hillewig, Elke; Verstraete, Koenraad

2017-03-01

Established methods to stage development of third molars for forensic age estimation are based on the evaluation of radiographs, which show a 2D projection. It has not been investigated whether these methods require any adjustments in order to apply them to stage third molars on magnetic resonance imaging (MRI), which shows 3D information. To prospectively study root stage assessment of third molars in age estimation using 3 Tesla MRI and to compare this with panoramic radiographs, in order to provide considerations for converting 2D staging into 3D staging and to determine the decisive root. All third molars were evaluated in 52 healthy participants aged 14-26 years using MRI in three planes. Three staging methods were investigated by two observers. In sixteen of the participants, MRI findings were compared with findings on panoramic radiographs. Decisive roots were palatal in upper third molars and distal in lower third molars. Fifty-seven per cent of upper third molars were not assessable on the radiograph, while 96.9% were on MRI. Upper third molars were more difficult to evaluate on radiographs than on MRI (p third molars were equally assessable on both imaging techniques (93.8% MRI, 98.4% radiograph), with no difference in level of difficulty (p = .375). Inter- and intra-observer agreement for evaluation was higher in MRI than in radiographs. In both imaging techniques lower third molars showed greater inter- and intra-observer agreement compared to upper third molars. MR images in the sagittal plane proved to be essential for staging. In age estimation, 3T MRI of third molars could be valuable. Some considerations are, however, necessary to transfer known staging methods to this 3D technique.

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure.

Science.gov (United States)

Nielsen, H B; Mladenovska, Z; Westermann, P; Ahring, B K

2004-05-05

A two-stage 68 degrees C/55 degrees C anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68 degrees C for periods of 36, 108, and 168 h, and subsequently digested at 55 degrees C. In a lab-scale experiment, the performance of a two-stage reactor system, consisting of a digester operating at 68 degrees C with a hydraulic retention time (HRT) of 3 days, connected to a 55 degrees C reactor with 12-day HRT, was compared with a conventional single-stage reactor running at 55 degrees C with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single-stage reactor. The 68 degrees C reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic/fermentative bacteria were significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. The density levels of methanogens utilizing H2/CO2 or formate were, however, in the same range for all reactors, although the degradation of these substrates was significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. Temporal temperature gradient electrophoresis profiles (TTGE) of the 68 degrees C reactor demonstrated a stable bacterial community along with a less divergent community of archaeal species. Copyright 2004 Wiley Periodicals, Inc.

A comparison of two intraosseous anesthetic techniques in mandibular posterior teeth.

Science.gov (United States)

Gallatin, Juliane; Reader, Al; Nusstein, John; Beck, Mike; Weaver, Joel

2003-11-01

A number of studies have evaluated the Stabident (Fairfax Dental, Miami) intraosseous anesthesia technique. A second intraosseous technique--the X-tip system (X-tip Technologies, Lakewood, N.J.)--has been introduced, but no scientific studies have yet compared its effectiveness to that of the Stabident system. The authors undertook a study to compare the two systems' anesthetic outcomes in primary intraosseous injections in mandibular posterior teeth. The authors, using a crossover design, randomly administered a primary Stabident intraosseous injection and a primary X-tip intraosseous injection, at two separate appointments, to 41 subjects. Subjects were asked if they perceived an increase in heart rate with the intraosseous injections. The research team blind-tested each subject's first molar, second molar and second premolar with a pulp tester at two-minute cycles for 60 minutes after the injection. Anesthesia was considered successful when two consecutive pulp tester readings of 80 were obtained. Anesthetic success rates for the Stabident technique and the X-tip technique, respectively, were 93 percent and 93 percent for the first molar; 95 percent and 95 percent for the second molar; and 81 percent and 83 percent for the second premolar, with no significant differences (P > .05) between the two techniques. For both intraosseous techniques, onset of pulpal anesthesia occurred within the first two minutes, but the duration of anesthesia declined steadily over the 60 minutes. Eighty-five percent of the subjects had a perceived increase in heart rate with the Stabident injection and 93 percent with the X-tip injection, with no significant differences (P > .05) between the techniques. The two primary intraosseous injection techniques were similar regarding anesthetic success, onset, duration and perceived heart rate increases.

Two-stage image denoising considering interscale and intrascale dependencies

Science.gov (United States)

Shahdoosti, Hamid Reza

2017-11-01

A solution to the problem of reducing the noise of grayscale images is presented. To consider the intrascale and interscale dependencies, this study makes use of a model. It is shown that the dependency between a wavelet coefficient and its predecessors can be modeled by the first-order Markov chain, which means that the parent conveys all of the information necessary for efficient estimation. Using this fact, the proposed method employs the Kalman filter in the wavelet domain for image denoising. The proposed method has two stages. The first stage employs a simple denoising algorithm to provide the noise-free image, by which the parameters of the model such as state transition matrix, variance of the process noise, the observation model, and the covariance of the observation noise are estimated. In the second stage, the Kalman filter is applied to the wavelet coefficients of the noisy image to estimate the noise-free coefficients. In fact, the Kalman filter is used to estimate the coefficients of high-frequency subbands from the coefficients of coarser scales and noisy observations of neighboring coefficients. In this way, both the interscale and intrascale dependencies are taken into account. Results are presented and discussed on a set of standard 8-bit grayscale images. The experimental results demonstrate that the proposed method achieves performances competitive with the state-of-the-art denoising methods in terms of both peak-signal-to-noise ratio and subjective visual quality.

Two stages of Kondo effect and competition between RKKY and Kondo in Gd-based intermetallic compound

Energy Technology Data Exchange (ETDEWEB)

Vaezzadeh, Mehdi [Department of Physics, K.N.Toosi University of Technology, P.O. Box 15875-4416, Tehran (Iran, Islamic Republic of)]. E-mail: mehdi@kntu.ac.ir; Yazdani, Ahmad [Tarbiat Modares University, P.O. Box 14155-4838, Tehran (Iran, Islamic Republic of); Vaezzadeh, Majid [Department of Physics, K.N.Toosi University of Technology, P.O. Box 15875-4416, Tehran (Iran, Islamic Republic of); Daneshmand, Gissoo [Department of Physics, K.N.Toosi University of Technology, P.O. Box 15875-4416, Tehran (Iran, Islamic Republic of); Kanzeghi, Ali [Department of Physics, K.N.Toosi University of Technology, P.O. Box 15875-4416, Tehran (Iran, Islamic Republic of)

2006-05-01

The magnetic behavior of Gd-based intermetallic compound (Gd{sub 2}Al{sub (1-x)}Au{sub x}) in the form of the powder and needle, is investigated. All the samples are an orthorhombic crystal structure. Only the compound with x=0.4 shows the Kondo effect (other compounds have a normal behavior). Although, for the compound in the form of powder, with x=0.4, the susceptibility measurement {chi}(T) shows two different stages. Moreover for (T>T{sub K2}) a fall of the value of {chi}(T) is observable, which indicates a weak presence of ferromagnetic phase. About the two stages of Kondo effect, we observe at the first (T{sub K1}) an increase of {chi}(T) and in the second stage (T{sub K2}) a new remarkable decrease of {chi}(T) (T{sub K1}>T{sub K2}). For the sample in the form of needles, the first stage is observable only under high magnetic field. This first stage could be corresponds to a narrow resonance between Kondo cloud and itinerant electron. The second stage, which is remarkably visible for the sample in the form of the powder, can be attribute to a complete polarization of Kondo cloud. Observation of these two Kondo stages could be due to the weak presence of RKKY contribution.

The dynamics of patients' life quality indices under the conditions of two-stage knee joint replacement

Directory of Open Access Journals (Sweden)

Shpinyak S.P.

2017-09-01

Full Text Available  The aim: to analyze the changes in the life quality indices of the patients with deep periprosthetic joint infection of the knee under the two-stage surgical treatment. Material and Methods. 57 patients who underwent two-stage revision-ary treatment in Research Institute of Traumatology, Orthopedics and Neurosurgery were interviewed with life quality questionnaire Short Form Medical Outcomes Study (SF 36 v.1. Interview results were compared with standardized population indices of SF-36 scales for males and females. Results. In all groups regardless of sex there was a general tendency for an increase in physical and psychological health component up to mean population values after the first stage of surgery and further growth after the second stage. Rehabilitation potential of psychomotor health was higher in women than in men. The ability to handle stress was lower in direct ratio with the patients' age. Conclusion. Two-stage reendoprosthetic treatment with articulating antimicrobial spacer implantation having high grade of fixation is an effective treatment method for deep periprosthetic infection which increases physical health and improves social functioning of patients.

Local Lunar Gravity Field Analysis over the South Pole-aitken Basin from SELENE Farside Tracking Data

Science.gov (United States)

Goossens, Sander Johannes; Ishihara, Yoshiaki; Matsumoto, Koji; Sasaki, Sho

2012-01-01

We present a method with which we determined the local lunar gravity field model over the South Pole-Aitken (SPA) basin on the farside of the Moon by estimating adjustments to a global lunar gravity field model using SELENE tracking data. Our adjustments are expressed in localized functions concentrated over the SPA region in a spherical cap with a radius of 45deg centered at (191.1 deg E, 53.2 deg S), and the resolution is equivalent to a 150th degree and order spherical harmonics expansion. The new solution over SPA was used in several applications of geophysical analysis. It shows an increased correlation with high-resolution lunar topography in the frequency band l = 40-70, and admittance values are slightly different and more leveled when compared to other, global gravity field models using the same data. The adjustments expressed in free-air anomalies and differences in Bouguer anomalies between the local solution and the a priori global solution correlate with topographic surface features. The Moho structure beneath the SPA basin is slightly modified in our solution, most notably at the southern rim of the Apollo basin and around the Zeeman crater

Continuous production of biohythane from hydrothermal liquefied cornstalk biomass via two-stage high-rate anaerobic reactors.

Science.gov (United States)

Si, Bu-Chun; Li, Jia-Ming; Zhu, Zhang-Bing; Zhang, Yuan-Hui; Lu, Jian-Wen; Shen, Rui-Xia; Zhang, Chong; Xing, Xin-Hui; Liu, Zhidan

2016-01-01

Biohythane production via two-stage fermentation is a promising direction for sustainable energy recovery from lignocellulosic biomass. However, the utilization of lignocellulosic biomass suffers from specific natural recalcitrance. Hydrothermal liquefaction (HTL) is an emerging technology for the liquefaction of biomass, but there are still several challenges for the coupling of HTL and two-stage fermentation. One particular challenge is the limited efficiency of fermentation reactors at a high solid content of the treated feedstock. Another is the conversion of potential inhibitors during fermentation. Here, we report a novel strategy for the continuous production of biohythane from cornstalk through the integration of HTL and two-stage fermentation. Cornstalk was converted to solid and liquid via HTL, and the resulting liquid could be subsequently fed into the two-stage fermentation systems. The systems consisted of two typical high-rate reactors: an upflow anaerobic sludge blanket (UASB) and a packed bed reactor (PBR). The liquid could be efficiently converted into biohythane via the UASB and PBR with a high density of microbes at a high organic loading rate. Biohydrogen production decreased from 2.34 L/L/day in UASB (1.01 L/L/day in PBR) to 0 L/L/day as the organic loading rate (OLR) of the HTL liquid products increased to 16 g/L/day. The methane production rate achieved a value of 2.53 (UASB) and 2.54 L/L/day (PBR), respectively. The energy and carbon recovery of the integrated HTL and biohythane fermentation system reached up to 79.0 and 67.7%, respectively. The fermentation inhibitors, i.e., 5-hydroxymethyl furfural (41.4-41.9% of the initial quantity detected) and furfural (74.7-85.0% of the initial quantity detected), were degraded during hydrogen fermentation. Compared with single-stage fermentation, the methane process during two-stage fermentation had a more efficient methane production rate, acetogenesis, and COD removal. The microbial distribution

Two stages and three components of the postural preparation to action.

Science.gov (United States)

Krishnan, Vennila; Aruin, Alexander S; Latash, Mark L

2011-07-01

Previous studies of postural preparation to action/perturbation have primarily focused on anticipatory postural adjustments (APAs), the changes in muscle activation levels resulting in the production of net forces and moments of force. We hypothesized that postural preparation to action consists of two stages: (1) Early postural adjustments (EPAs), seen a few hundred ms prior to an expected external perturbation and (2) APAs seen about 100 ms prior to the perturbation. We also hypothesized that each stage consists of three components, anticipatory synergy adjustments seen as changes in covariation of the magnitudes of commands to muscle groups (M-modes), changes in averaged across trials levels of muscle activation, and mechanical effects such as shifts of the center of pressure. Nine healthy participants were subjected to external perturbations created by a swinging pendulum while standing in a semi-squatting posture. Electrical activity of twelve trunk and leg muscles and displacements of the center of pressure were recorded and analyzed. Principal component analysis was used to identify four M-modes within the space of muscle activations using indices of integrated muscle activation. This analysis was performed twice, over two phases, 400-700 ms prior to the perturbation and over 200 ms just prior to the perturbation. Similar robust results were obtained using the data from both phases. An index of a multi-M-mode synergy stabilizing the center of pressure displacement was computed using the framework of the uncontrolled manifold hypothesis. The results showed high synergy indices during quiet stance. Each of the two stages started with a drop in the synergy index followed by a change in the averaged across trials activation levels in postural muscles. There was a very long electromechanical delay during the early postural adjustments and a much shorter delay during the APAs. Overall, the results support our main hypothesis on the two stages and three components

Two-stage bargaining with coverage extension in a dual labour market

DEFF Research Database (Denmark)

Roberts, Mark A.; Stæhr, Karsten; Tranæs, Torben

2000-01-01

This paper studies coverage extension in a simple general equilibrium model with a dual labour market. The union sector is characterized by two-stage bargaining whereas the firms set wages in the non-union sector. In this model firms and unions of the union sector have a commonality of interest...

Spawning strategies and transport of early stages of the two Cape ...

African Journals Online (AJOL)

Seasonal and short-term variability of environmental parameters influence the spawning strategies of fish species. In this study, the spawning strategies and the transport of early stages of the two Cape hake species off South Africa were investigated. Distribution of eggs and larvae of Merluccius paradoxus and M. capensis ...

Numerical Investigation and Experimental Demonstration of Chaos from Two-Stage Colpitts Oscillator in the Ultrahigh Frequency Range

DEFF Research Database (Denmark)

Bumeliene, S.; Tamasevicius, A.; Mykolaitis, G.

2006-01-01

A hardware prototype of the two-stage Colpitts oscillator employing the microwave BFG520 type transistors with the threshold frequency of 9 GHz and designed to operate in the ultrahigh frequency range (300–1000 MHz) is described. The practical circuit in addition to the intrinsic two-stage oscill......A hardware prototype of the two-stage Colpitts oscillator employing the microwave BFG520 type transistors with the threshold frequency of 9 GHz and designed to operate in the ultrahigh frequency range (300–1000 MHz) is described. The practical circuit in addition to the intrinsic two......-stage oscillator contains an emitter follower acting as a buffer and minimizing the influence of the load. The circuit is investigated both numerically and experimentally. Typical phase portraits, Lyapunov exponents, Lyapunov dimension and broadband continuous power spectra are presented. The main advantage...

Two-Stage Classification Approach for Human Detection in Camera Video in Bulk Ports

Directory of Open Access Journals (Sweden)

Mi Chao

2015-09-01

Full Text Available With the development of automation in ports, the video surveillance systems with automated human detection begun to be applied in open-air handling operation areas for safety and security. The accuracy of traditional human detection based on the video camera is not high enough to meet the requirements of operation surveillance. One of the key reasons is that Histograms of Oriented Gradients (HOG features of the human body will show great different between front & back standing (F&B and side standing (Side human body. Therefore, the final training for classifier will only gain a few useful specific features which have contribution to classification and are insufficient to support effective classification, while using the HOG features directly extracted by the samples from different human postures. This paper proposes a two-stage classification method to improve the accuracy of human detection. In the first stage, during preprocessing classification, images is mainly divided into possible F&B human body and not F&B human body, and then they were put into the second-stage classification among side human and non-human recognition. The experimental results in Tianjin port show that the two-stage classifier can improve the classification accuracy of human detection obviously.

Two-axis tracking using translation stages for a lens-to-channel waveguide solar concentrator.

Science.gov (United States)

Liu, Yuxiao; Huang, Ran; Madsen, Christi K

2014-10-20

A two-axis tracking scheme designed for tracker and a translation stage is discussed. The translation stage is used for adjusting positions for seasonal sun movement. It has two-dimensional x-y tracking instead of horizontal movement x-only. This tracking method is compatible with planar waveguide solar concentrators. A prototype system with 50x concentration shows >75% optical efficiency throughout the year in simulation and >65% efficiency experimentally. This efficiency can be further improved by the use of anti-reflection layers and a larger waveguide refractive index.

Retrograde cystography US. A new ultrasound technique for the diagnosis and staging of vesicoureteral reflux

International Nuclear Information System (INIS)

Farina, R.; Arena, C.; Pennisi, F.; Di Benedetto, V.; Politi, G.; Di Benedetto, A.

1999-01-01

The authors investigated the accuracy of a new US (ultrasound) investigation technique, called retrograde cystography US, in the early diagnosis and staging of vesicoureteral reflux. 5 patients, aged 3 months to 10 years, suffering from hydronephrosis and/or pyelonephritis, were examined using retrograde cystography US followed by conventional retrograde cystography. Retrograde cystography US consists in the transcatheter introduction of a contrast agent into the bladder and a subsequent color Doppler examination to show or exclude the presence of reflux. Superpubic scanning of bladder, ureters and pyelocaliceal cavity was performed after echo contrast agent introduction to assess the reflux grade. US was performed with an Esaote AU 590 asynchronous scanner with a 3.5 MHz convex probe. The total agreement of conventional and US findings seems to confirm the importance of the US method for the diagnosis and staging of vesicoureteral reflux [it

Evaluation of dilatometric techniques for studies of sintering kinetics

International Nuclear Information System (INIS)

El-Sayed Ali, M.; Toft Soerensen, O.

1985-04-01

The kinetics of the initial sintering stage of CeO 2 is evaluated by three different techniques: constant heating rate dilatometry, constant shrinkage rate dilatometry and a new technique recently introduced by the authors called Stepwise Isothermal Dilatometry (SID). Comparative measurements with these techniques showed that too high activation energies were obtained with the two first techniques, both of which can be termed as nonisothermal, whereas activation energies comparable to those reported for cation diffusion in other fluorite oxides were obtained with the latter technique. Of the three techniques SID is thus considered to be the most accurate for studies of the sintering kinetics. In contrast to the two nonisothermal techniques SID has the further advantage that both the controlling mechanism and its activation energy can be determined in a single experiment. From the SID-measurement it was concluded that the initial sintering stage of CeO 2 is controlled by grain-boundary diffusion. (author)

Optimisation of Refrigeration System with Two-Stage and Intercooler Using Fuzzy Logic and Genetic Algorithm

Directory of Open Access Journals (Sweden)

Bayram Kılıç

2017-04-01

Full Text Available Two-stage compression operation prevents excessive compressor outlet pressure and temperature and this operation provides more efficient working condition in low-temperature refrigeration applications. Vapor compression refrigeration system with two-stage and intercooler is very good solution for low-temperature refrigeration applications. In this study, refrigeration system with two-stage and intercooler were optimized using fuzzy logic and genetic algorithm. The necessary thermodynamic characteristics for optimization were estimated with Fuzzy Logic and liquid phase enthalpy, vapour phase enthalpy, liquid phase entropy, vapour phase entropy values were compared with actual values. As a result, optimum working condition of system was estimated by the Genetic Algorithm as -6.0449 oC for evaporator temperature, 25.0115 oC for condenser temperature and 5.9666 for COP. Morever, irreversibility values of the refrigeration system are calculated.

A Two-Stage Framework for 3D Face Reconstruction from RGBD Images.

Science.gov (United States)

Wang, Kangkan; Wang, Xianwang; Pan, Zhigeng; Liu, Kai

2014-08-01

This paper proposes a new approach for 3D face reconstruction with RGBD images from an inexpensive commodity sensor. The challenges we face are: 1) substantial random noise and corruption are present in low-resolution depth maps; and 2) there is high degree of variability in pose and face expression. We develop a novel two-stage algorithm that effectively maps low-quality depth maps to realistic face models. Each stage is targeted toward a certain type of noise. The first stage extracts sparse errors from depth patches through the data-driven local sparse coding, while the second stage smooths noise on the boundaries between patches and reconstructs the global shape by combining local shapes using our template-based surface refinement. Our approach does not require any markers or user interaction. We perform quantitative and qualitative evaluations on both synthetic and real test sets. Experimental results show that the proposed approach is able to produce high-resolution 3D face models with high accuracy, even if inputs are of low quality, and have large variations in viewpoint and face expression.

Electron-gun Evaporation of Cu and In thin films as Precursors for CuInSe{sub 2} Formation; Evaporacion mediante Canon de Electrones de Laminas Delgadas de Cu e In como Precursores para la Obtencion de CuInSe{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Caballero, R; Guillen, C

2001-07-01

In the present investigation CuInSe{sub 2} is obtained in two stages: sequential evaporation of Cu and In using an electron gun evaporator on substrates up to 30 x 30 cm''2, and a posterior selenization of the deposited films. The study is mainly focused on the first stage, in where the control of the different evaporation parameters of the metal precursors is essential. Electrical measurements are carried out, and also the topography and the thickness are determined with the object of studying the properties and homogeneity of the thin films. (Author) 19 refs.

Electron-gun Evaporation of Cu and In thin films as Precursors for CuInSe{sub 2} Formation; Evaporacion mediante Canon de Electrones de Laminas Delgadas de Cu e In como Precursores para la Obtencion de CuInSe{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Caballero, R.; Guillen, C.

2001-07-01

In the present investigation CuInSe{sub 2} is obtained in two stages: sequential evaporation of Cu and In using an electron gun evaporator on substrates up to 30 x 30 cm''2, and a posterior selenization of the deposited films. The study is mainly focused on the first stage, in where the control of the different evaporation parameters of the metal precursors is essential. Electrical measurements are carried out, and also the topography and the thickness are determined with the object of studying the properties and homogeneity of the thin films. (Author) 19 refs.

Two-stage approach for risk estimation of fetal trisomy 21 and other aneuploidies using computational intelligence systems.

Science.gov (United States)

Neocleous, A C; Syngelaki, A; Nicolaides, K H; Schizas, C N

2018-04-01

To estimate the risk of fetal trisomy 21 (T21) and other chromosomal abnormalities (OCA) at 11-13 weeks' gestation using computational intelligence classification methods. As a first step, a training dataset consisting of 72 054 euploid pregnancies, 295 cases of T21 and 305 cases of OCA was used to train an artificial neural network. Then, a two-stage approach was used for stratification of risk and diagnosis of cases of aneuploidy in the blind set. In Stage 1, using four markers, pregnancies in the blind set were classified into no risk and risk. No-risk pregnancies were not examined further, whereas the risk pregnancies were forwarded to Stage 2 for further examination. In Stage 2, using seven markers, pregnancies were classified into three types of risk, namely no risk, moderate risk and high risk. Of 36 328 unknown to the system pregnancies (blind set), 17 512 euploid, two T21 and 18 OCA were classified as no risk in Stage 1. The remaining 18 796 cases were forwarded to Stage 2, of which 7895 euploid, two T21 and two OCA cases were classified as no risk, 10 464 euploid, 83 T21 and 61 OCA as moderate risk and 187 euploid, 50 T21 and 52 OCA as high risk. The sensitivity and the specificity for T21 in Stage 2 were 97.1% and 99.5%, respectively, and the false-positive rate from Stage 1 to Stage 2 was reduced from 51.4% to ∼1%, assuming that the cell-free DNA test could identify all euploid and aneuploid cases. We propose a method for early diagnosis of chromosomal abnormalities that ensures that most T21 cases are classified as high risk at any stage. At the same time, the number of euploid cases subjected to invasive or cell-free DNA examinations was minimized through a routine procedure offered in two stages. Our method is minimally invasive and of relatively low cost, highly effective at T21 identification and it performs better than do other existing statistical methods. Copyright © 2017 ISUOG. Published by John Wiley & Sons Ltd. Copyright �

High Performance Gasification with the Two-Stage Gasifier

DEFF Research Database (Denmark)

Gøbel, Benny; Hindsgaul, Claus; Henriksen, Ulrik Birk

2002-01-01

, air preheating and pyrolysis, hereby very high energy efficiencies can be achieved. Encouraging results are obtained at a 100 kWth laboratory facility. The tar content in the raw gas is measured to be below 25 mg/Nm3 and around 5 mg/Nm3 after gas cleaning with traditional baghouse filter. Furthermore...... a cold gas efficiency exceeding 90% is obtained. In the original design of the two-stage gasification process, the pyrolysis unit consists of a screw conveyor with external heating, and the char unit is a fixed bed gasifier. This design is well proven during more than 1000 hours of testing with various...... fuels, and is a suitable design for medium size gasifiers....

Fleet Planning Decision-Making: Two-Stage Optimization with Slot Purchase

Directory of Open Access Journals (Sweden)

Lay Eng Teoh

2016-01-01

Full Text Available Essentially, strategic fleet planning is vital for airlines to yield a higher profit margin while providing a desired service frequency to meet stochastic demand. In contrast to most studies that did not consider slot purchase which would affect the service frequency determination of airlines, this paper proposes a novel approach to solve the fleet planning problem subject to various operational constraints. A two-stage fleet planning model is formulated in which the first stage selects the individual operating route that requires slot purchase for network expansions while the second stage, in the form of probabilistic dynamic programming model, determines the quantity and type of aircraft (with the corresponding service frequency to meet the demand profitably. By analyzing an illustrative case study (with 38 international routes, the results show that the incorporation of slot purchase in fleet planning is beneficial to airlines in achieving economic and social sustainability. The developed model is practically viable for airlines not only to provide a better service quality (via a higher service frequency to meet more demand but also to obtain a higher revenue and profit margin, by making an optimal slot purchase and fleet planning decision throughout the long-term planning horizon.

Late-stage pharmaceutical R&D and pricing policies under two-stage regulation.