Percolation behavior of tritiated water into a soil packed bed

Energy Technology Data Exchange (ETDEWEB)

Honda, T.; Katayama, K.; Uehara, K.; Fukada, S. [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka (Japan); Takeishi, T. [Faculty of Engineering, Kyushu University, Motooka Nishi-ku, Fukuoka (Japan)

2015-03-15

A large amount of cooling water is used in a D-T fusion reactor. The cooling water will contain tritium with high concentration because tritium can permeate metal walls at high temperature easily. A development of tritium handling technology for confining tritiated water in the fusion facility is an important issue. In addition, it is also important to understand tritium behavior in environment assuming severe accidents. In this study, percolation experiments of tritiated water in soil packed bed were carried out and tritium behavior in soil was discussed. Six soil samples were collected in Hakozaki campus of Kyushu University. These particle densities were of the same degree as that of general soils and moisture contents were related to BET surface area. For two soil samples used in the percolation experiment of tritiated water, saturated hydraulic conductivity agreed well with the estimating value by Creager. Tritium retention ratio in the soil packed bed was larger than water retention. This is considered to be due to an effect of tritium sorption on the surface of soil particles. The isotope exchange capacity estimated by assuming that H/T ratio of supplied tritiated water and H/T ratio of surface water of soil particle was equal was comparable to that on cement paste and mortar which were obtained by exposure of tritiated water vapor. (authors)

Percolation behavior of tritiated water into a soil packed bed

International Nuclear Information System (INIS)

Honda, T.; Katayama, K.; Uehara, K.; Fukada, S.; Takeishi, T.

2015-01-01

A large amount of cooling water is used in a D-T fusion reactor. The cooling water will contain tritium with high concentration because tritium can permeate metal walls at high temperature easily. A development of tritium handling technology for confining tritiated water in the fusion facility is an important issue. In addition, it is also important to understand tritium behavior in environment assuming severe accidents. In this study, percolation experiments of tritiated water in soil packed bed were carried out and tritium behavior in soil was discussed. Six soil samples were collected in Hakozaki campus of Kyushu University. These particle densities were of the same degree as that of general soils and moisture contents were related to BET surface area. For two soil samples used in the percolation experiment of tritiated water, saturated hydraulic conductivity agreed well with the estimating value by Creager. Tritium retention ratio in the soil packed bed was larger than water retention. This is considered to be due to an effect of tritium sorption on the surface of soil particles. The isotope exchange capacity estimated by assuming that H/T ratio of supplied tritiated water and H/T ratio of surface water of soil particle was equal was comparable to that on cement paste and mortar which were obtained by exposure of tritiated water vapor. (authors)

Diffusion of tritiated water in coastal areas

International Nuclear Information System (INIS)

Fukuda, M.; Kasai, A.; Imai, T.; Amano, H.; Yanase, N.

1980-01-01

The diffusion of tritiated water discharged by Japan Atomic Energy Research Institute at shore line has been investigated. In continuous discharge, the concentration of tritiated water in samples taken at a point downstream fluctuates largely. To reveal the cause, dye diffusion experiments were made in the coastal area. The shapes of dye cloud were photographed by a remote-control camera suspended from a captive balloon as color pictures. The movement of dye is so complex that a three-dimensional model must be employed to assess the diffusion in coastal areas

Studies on carcinogenic effect of tritiated water

International Nuclear Information System (INIS)

Zou Shuai; Wang Hui; Li Maohe; Lin Suqin

1994-09-01

Studies on carcinogenic effect of tritiated water is introduced in two parts. The first part is an in vitro study in which CHL-1 cells were exposed to tritiated water (9.25 x 10 5 ∼ 3.5 x 10 6 Bq/ml) for 24 ∼ 96 h and the accumulated dose was from 0.055 to 0.88 Gy. In order to estimate RBE of tritium for malignant transformation in CHL-1 cells, the induction of malignant transformation in CHL-1 cells by exposure to gamma rays of 137 Cs was tested. Based on the transformation rates, the RBE of tritium for malignant transformation in CHL-1 cells was estimated to be 1.6. The second part is an in vivo study. In the study, rats were fed with tritiated water (2.22 x 10 5 and 1.11 x 10 5 Bq/ml) for 1.5 a. Rats in control group were fed with tap water. Results showed that in the statistics, the differences in the total tumor incidence and malignant tumor incidence between high and low dose rate groups and control groups were remarkably significant

Tritium recovery from tritiated water with a two-stage palladium membrane reactor

International Nuclear Information System (INIS)

Birdsell, S.A.; Willms, R.S.

1997-01-01

A process to recover tritium from tritiated water has been successfully demonstrated at TSTA. The 2-stage palladium membrane reactor (PMR) is capable of recovering tritium from water without generating additional waste. This device can be used to recover tritium from the substantial amount of tritiated water that is expected to be generated in the International Thermonuclear Experimental Reactor both from torus exhaust and auxiliary operations. A large quantity of tritiated waste water exists world wide because the predominant method of cleaning up tritiated streams is to oxidize tritium to tritiated water. The latter can be collected with high efficiency for subsequent disposal. The PMR is a combined catalytic reactor/permeator. Cold (non-tritium) water processing experiments were run in preparation for the tritiated water processing tests. Tritium was recovered from a container of molecular sieve loaded with 2,050 g (2,550 std. L) of water and 4.5 g of tritium. During this experiment, 27% (694 std. L) of the water was processed resulting in recovery of 1.2 g of tritium. The maximum water processing rate for the PMR system used was determined to be 0.5 slpm. This correlates well with the maximum processing rate determined from the smaller PMR system on the cold test bench and has resulted in valuable scale-up and design information

Tritium recovery from tritiated water with a two-stage palladium membrane reactor

Energy Technology Data Exchange (ETDEWEB)

Birdsell, S.A.; Willms, R.S.

1997-04-01

A process to recover tritium from tritiated water has been successfully demonstrated at TSTA. The 2-stage palladium membrane reactor (PMR) is capable of recovering tritium from water without generating additional waste. This device can be used to recover tritium from the substantial amount of tritiated water that is expected to be generated in the International Thermonuclear Experimental Reactor both from torus exhaust and auxiliary operations. A large quantity of tritiated waste water exists world wide because the predominant method of cleaning up tritiated streams is to oxidize tritium to tritiated water. The latter can be collected with high efficiency for subsequent disposal. The PMR is a combined catalytic reactor/permeator. Cold (non-tritium) water processing experiments were run in preparation for the tritiated water processing tests. Tritium was recovered from a container of molecular sieve loaded with 2,050 g (2,550 std. L) of water and 4.5 g of tritium. During this experiment, 27% (694 std. L) of the water was processed resulting in recovery of 1.2 g of tritium. The maximum water processing rate for the PMR system used was determined to be 0.5 slpm. This correlates well with the maximum processing rate determined from the smaller PMR system on the cold test bench and has resulted in valuable scale-up and design information.

A miniature discriminating monitor for tritiated water vapour

Energy Technology Data Exchange (ETDEWEB)

Edwards, R.A.H.; Ravazzani, A.; Pacenti, P. [European Commission, JRC, Institute for Advanced Material, Ispra, Vatican City State, Holy See (Italy); Campi, F. [Nuclear Engineering Dept., Polytechnic of Milan (Italy)

1998-07-01

In detecting tritium in air (or other gas) for worker safety, it is important to discriminate between tritiated water vapour and elemental tritium, because the first is much more easily absorbed in the lungs. We haveinvented (patent pending) an innovative discriminating monitor which works better than existing designs, and is much smaller. The air (or other sample gas) passes over a large surface area of solid scintillator, which is surface-treated to make it hygroscopic. Tritiated water vapour in the air exchanges continuously, rapidly and reversibly with the water in the thin hygroscopic layer; which is of the order of 1 micron thick. The beta-emissions from tritium in the hygroscopic layer hit the solid scintillator, causing flashes of light that are detected by a photomultiplier. The new discriminating monitor for tritiated species in air offers superior performance to existing discriminating monitors, and is much smaller. It is planned to develop a portable version which could serve as a personal tritium monitor. (authors)

Use of tritiated water for estimating body composition in grazing ewes

International Nuclear Information System (INIS)

Russel, A.J.F.; Foot, J.Z.; McFarlane, D.M.

1982-01-01

Tritiated water was used to estimate total body water, body composition and water turnover of non-pregnant, pregnant, non-lactating and lactating grazing sheep. Body composition was estimated from equilibrated and extrapolated values of tritiated water space. These methods both overestimated the total body water measured directly. Body fat could be predicted satisfactorily from tritiated water space within the physiological states of ewes, i.e. lactating, pregnant, etc., although for lactating ewes the error of prediction is greater. It appears inadvisable at this stage to use equations derived from all classes of ewes to estimate body fat in ewes of any one physiological state. Water turnover varied, with the physiological state being highest for lactating ewes. (author)

Conversion of tritium gas to tritiated water

International Nuclear Information System (INIS)

Papagiannakopoulos, P.J.; Easterly, C.E.

1979-05-01

The mechanisms of conversion of tritium gas to tritiated water (HTO) have been examined for several tritium gaseous mixtures. The physical and chemical processes involved in the self-radiolysis of such mixtures have been analyzed and the kinetics involved in the formation of HTO has been presented. It has been determined that the formation of the H and/or OH free radicals, as intermediate species, are of significance in the formation of HTO. Therefore, the problem of reducing the rate of formation of tritiated water in a mixture of gaseous tritium with atmospheric components is one of finding an effective scavenger for the H and/or OH free radicals

Tritium sorption behavior on the percolation of tritiated water into a soil packed bed

Energy Technology Data Exchange (ETDEWEB)

Furuichi, Kazuya, E-mail: kfuruichi@aees.kyushu-u.ac.jp [Department of Advanced Energy Engineering, Kyushu University, 6-1, Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Katayama, Kazunari; Date, Hiroyuki [Department of Advanced Energy Engineering, Kyushu University, 6-1, Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Takeishi, Toshiharu [Factory of Engineering, Kyushu University, 744 Motooka Nishi-ku, Fukuoka 819-0395 (Japan); Fukada, Satoshi [Department of Advanced Energy Engineering, Kyushu University, 6-1, Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan)

2016-11-01

Highlights: • We establish the permeation model of tritiated water in the soil layer. • Saturated hydraulic conductivity of water in soil was gained by using the model. • The isotope exchange reaction coefficient was good agreement with experimental data. - Abstract: Development of tritium transport model in natural soil is an important issue from a viewpoint of safety of fusion reactors. The spill of a large amount of tritiated water to the environment is a concern accident because huge tritiated water is handled in a fusion plant. In this work, a simple tritium transport model was proposed based on the tritium transport model in porous materials. The overall mass transfer coefficient representing isotope exchange reaction between tritiated water and structural water in soil particles was obtained by numerically analyzing the result of the percolation experiment of tritiated water into the soil packed bed. Saturated hydraulic conductivity in the natural soil packed bed was obtained to be 0.033 mm/s. By using this value, the overall mass transfer capacity coefficients representing the isotope exchange reaction between tritiated water percolating through the packed bed and overall structural water on soil particles was determined to be 6.0 × 10{sup −4} 1/s. This value is much smaller than the mass transfer capacity coefficient between tritiated water vapor and water on concrete material and metals.

Water flux in animals: analysis of potential errors in the tritiated water method

International Nuclear Information System (INIS)

Nagy, K.A.; Costa, D.

1979-03-01

Laboratory studies indicate that tritiated water measurements of water flux are accurate to within -7 to +4% in mammals, but errors are larger in some reptiles. However, under conditions that can occur in field studies, errors may be much greater. Influx of environmental water vapor via lungs and skin can cause errors exceeding +-50% in some circumstances. If water flux rates in an animal vary through time, errors approach +-15% in extreme situations, but are near +-3% in more typical circumstances. Errors due to fractional evaporation of tritiated water may approach -9%. This error probably varies between species. Use of an inappropriate equation for calculating water flux from isotope data can cause errors exceeding +-100%. The following sources of error are either negligible or avoidable: use of isotope dilution space as a measure of body water volume, loss of nonaqueous tritium bound to excreta, binding of tritium with nonaqueous substances in the body, radiation toxicity effects, and small analytical errors in isotope measurements. Water flux rates measured with tritiated water should be within +-10% of actual flux rates in most situations

Water flux in animals: analysis of potential errors in the tritiated water method

Energy Technology Data Exchange (ETDEWEB)

Nagy, K.A.; Costa, D.

1979-03-01

Laboratory studies indicate that tritiated water measurements of water flux are accurate to within -7 to +4% in mammals, but errors are larger in some reptiles. However, under conditions that can occur in field studies, errors may be much greater. Influx of environmental water vapor via lungs and skin can cause errors exceeding +-50% in some circumstances. If water flux rates in an animal vary through time, errors approach +-15% in extreme situations, but are near +-3% in more typical circumstances. Errors due to fractional evaporation of tritiated water may approach -9%. This error probably varies between species. Use of an inappropriate equation for calculating water flux from isotope data can cause errors exceeding +-100%. The following sources of error are either negligible or avoidable: use of isotope dilution space as a measure of body water volume, loss of nonaqueous tritium bound to excreta, binding of tritium with nonaqueous substances in the body, radiation toxicity effects, and small analytical errors in isotope measurements. Water flux rates measured with tritiated water should be within +-10% of actual flux rates in most situations.

Dose contribution from metabolized organically bound tritium after chronic tritiated water intakes in humans

International Nuclear Information System (INIS)

Trivedi, A.; Lamothe, E.; Galeriu, D.

2001-01-01

Our earlier study of acute tritiated water intakes in humans has demonstrated that the dose contribution from metabolized organically bound tritium is less than 10% of the body water dose. To further demonstrate that the dose contribution from the organically bound tritium per unit intake of tritiated water is the same, regardless of whether the intake is acute (all at once) or chronic (spread over time), urine samples from six male radiation workers with chronic tritiated water intakes were collected and analyzed for tritium. These workers have a well-documented dose history and a well-controlled tritium bioassay database, providing assurance that their tritium intakes were in the form of tritiated water. Each month for a full calendar year, urine samples were collected from each exposed worker. The monthly concentration of tritium-in-urine for each exposed worker was no lower than 104 Bq L -1 but no higher than 105 Bq L -1 . These urine samples were analyzed for tritiated water and organically bound tritium to determine the ratio of these tritiated species in urine. The average ratio of tritiated water to organically bound tritium in urine for each exposed worker was 330-129 (range, 297-589). In calculating the dose to these workers, we assumed that, under steady-state conditions, the ratio of the specific activity of tritium ( 3 H activity per gH) in the organic matter and water fractions of urine is representative of the ratio of the specific activity of tritium in the organic matter and water fractions of soft tissue. A mathematical model was developed and used to estimate the dose increase from the metabolized organically bound tritium based on the ratio of tritiated water to organically bound tritium in urine. The resulting average dose from the organically bound tritium was 6.9-3.1% (range, 4.7-9.9%) of the body water dose for the six male workers, and agrees well with the value obtained from our acute tritiated water intakes study in humans. The observed

Tritium retention in the femoral bone marrow and spleens of mice receiving single intravenous injections of tritiated water and tritiated thymidine

International Nuclear Information System (INIS)

Joshima, Hisamasa; Matsushita, Satoru; Fukutsu, Kumiko; Kashima, Masatoshi

1987-01-01

To derive parameters necessary for evaluating the possible hazards of tritium, retention of tritium in total and TCA-insoluble fractions of the femoral marrow and spleen of mice were observed after single intravenous injections of tritiated water and tritiated thymidine. Retention curves of tritium in TCA-insoluble fractions of the femoral marrow and spleen were resolved fairly well into two exponential components. After injecting tritiated thymidine, most of the activity was detected in the TCA-insoluble fraction. Tritium in this fraction decreased with half-times of 2.2 days in the femoral marrow and 3.6 days in the spleen as the first component, and 23.9 days and 30.5 days, respectively, as the second component. After tritiated water injections, the tritium incorporated into the TCA-insoluble fraction was quite small. Most of the activity was considered to be in the TCA-soluble fraction. Tritium in this fraction was estimated to decrease with half-times of 2.6 days in the femoral marrow and 2.3 days in the spleen as the first component, and 8.0 days and 8.2 days, respectively, as the second component. It is concluded that the retention curves of tritium in the bone marrow are similar to those in the spleen for tritiated water, but not for tritiated thymidine. (author)

Review of tritiated water concentration technology

International Nuclear Information System (INIS)

Ma Hongbin

2014-01-01

In order to cooperate with the construction of the spent fuel reprocessing plant in China, the research and application status of tritiated water concentration technology at home and abroad were summarized. Some suggestions for the technology research route in China were put forward. (author)

Tritium conversion in tritiated water: study of the involved reactions: a literature survey

International Nuclear Information System (INIS)

Ballereau, P.

1987-10-01

According to ICRP publication 30, hazards due to molecular tritium are not significant in comparison to hazards due to the oxidated form: tritiated water. It is thus important to know the kinetics of tritium/tritiated water conversion to obtain a realistic evaluation of the risks for the environment at level of present facilities and of future nuclear fusion facilities. Laboratory experiments in static contained conditions have shown that tritiated water is produced by two mechanisms: gas phase oxidation, hydrogen isotopic exchange with water. The periods found are relatively long and difficult to specify. In terrestrial atmosphere, the two mechanisms intervening in tritiated water formation are photochemical oxidation and biochemical reactions occurring in soil and in vegetation aerial parts. The corresponding periods are of some years for the first one, of some hours for the second one [fr

Tritiated water retention on maize and beans after an acute contamination

International Nuclear Information System (INIS)

Nulman, R.; Bravo, G.; Ortiz M, J.R.; Archundia, C.

1977-01-01

Although tritium is released in large quantities into environment by nuclear industries and peaceful radioisotope utilization, its behavior is not well known. The International Atomic Energy Agency is sponsoring an international study group to obtain more information about tritiated water (HTO) behavior in different ecological systems. This paper presents the studies made on corn and beans after an acute application of tritiated water during their early stages of growth on an experimental field. Sampling and radiochemical analytical methods of tritium and its behaviour on that plants during their growth cycle are outlined. It is shown that the tritiated water retention plot has at least two components, with effective half lifes of about 10 and 100 days for corn, and 8 and 40 days for beans. (author)

Tritium content in some organs and the DNA of rat liver cells following short term administration of tritiated food, tritiated protein or tritiated water

International Nuclear Information System (INIS)

Rochalska, M.; Szot, Z.

1979-01-01

Male Wistar rats were given equivalent doses of various tritium compounds, namely tritiated food (TF), tritiated protein (TP) or tritiated water (TW) for 5 days. On the 6th day of the experiment tritium radioactivity of dry tissues and the DNA of liver cells was determined. DNA of liver cells of animals given TP contained 13-23 times more tritium than that of rats receiving TW. Incorporation of tritium from TF into the examined tissues was found to be higher than that from TP or TW, with the exception of the brain which revealed the highest tritium content after TP. Tritium concentration in lungs, small intestine, muscle, skin and femur of animals given TF or TP did not differ significantly. (author)

Measurement of transpiration and biomass of coconut palm with tritiated water

International Nuclear Information System (INIS)

Vasu, K.; Wahid, P.A.

1990-01-01

Measurements of transpiration rate and biomass of coconut palm have been made using tritiated water as a tracer. The method of tracer injection into the coconut trunk and the extraction of tritiated water from coconut leaves are outlined. The transpiration rate of the tree selected for the study was found to be 2.2 litres/hour with a total biomass of 172 kg. (author). 8 refs., 3 tabs

Design of an electrolysis cell for highly tritiated water

International Nuclear Information System (INIS)

Rahier, A.; Baetsle, L.; Buggeman, A.; Cornelissen, R.; Goossens, W.

1985-01-01

Within the framework of the European fusion technology programme, SCK/CEN has started the development of a 100 ml per day electrolyser for decomposing the highly tritiated water that will be formed when tritium is extracted from the breeder or when the plasma exhaust is purified. Safety and reliability of this electrolytic system will have to be guaranteed for at least 10 4 working hours. Three different cell configurations are being studied one of which is most promising because of its low tritiated water inventory (about 12 ml), its low working temperature ( 0 C) and other advantages such as avoiding any recirculation of radioactive streams

Radiolysis of water confined in zeolites 4A: application to tritiated water storage

International Nuclear Information System (INIS)

Frances, Laetitia

2014-01-01

Self-radiolysis of tritiated water (HTO) adsorbed in zeolites 4A shows differences compared to free-bulk water radiolysis. We studied the roles of zeolites on that. We took special care with the influence of water loading ratio. We first exposed zeolites to external irradiations, reproducing selectively the dose or the dose rate measured in the case of tritiated water storage. This strategy enables the characterising of the samples after their irradiation since they are not contaminated by tritium. Those experiments revealed the high stability of zeolites 4A. We used a second approach which consisted in studying the precise case of self-radiolysis of tritiated water, in order to obtain radiolytic yields representative of HTO storage. The comparison between the quantities of gas released when zeolites are exposed to the three different sources that we used (electrons accelerated at 10 MeV, γ released by radioactive decay of 137 Cs and β - released by radioactive decay of tritium) revealed the strong influence of the dose rate. Moreover, whatever the irradiation source, zeolites 4A first favour hydrogen release and secondarily oxygen release too. On the contrary, zeolites favour next a recombination between those radiolytic products, with a dependence on their water loading ratio. Several processes are discussed to explain such a phenomena, not noticed during the free-bulk water radiolysis. (author) [fr

Effect of chronic ingestion of tritiated water and tritium organically bound in food on growth and reproductive functions of rats

International Nuclear Information System (INIS)

Pietrzak-Flis, Z.; Radwan, I.

1982-01-01

An effect of chronic ingestion of tritiated water and tritiated food on growth and reproduction of Wistar rats was evaluated. The animals were exposed during one or three successive generations. Ingestion of tritiated water at activity of 185.0 and 370.0 kBq/ml or tritiated food at activity of 144.3 kBq/g affected growth of the first generation (F 1 ) rats. In groups exposed to tritiated water the effect was transient. Exposure to tritiated food at 48.1 kBq/g or to tritiated water at the 37.0 kBq/ml affected the growth of F 2 generation rats only. A significant reduction in a relative testis tests weight was observed in a group exposed to tritiated water at activity of 370.0 kBq/ml, while sperm production was affected in all exposed groups. Ingestion of tritiated food caused higher reduction in sperm count than tritiated water. The effect of tritium on growth of rats and ability for sperm production depended on the absorbed dose and the form of ingested tritium. (author)

A suggested revision to the specific activity limit for tritiated water transported as LSA-II

International Nuclear Information System (INIS)

Nandakumar, A.N.

2003-01-01

Tritiated water of specific activity not greater than 0.8 TBq L -1 is classified as LSA-II. This paper demonstrates by some simple calculations that the dose that may result from an accident involving tritiated water of this specific activity is very low and suggests that even if the specific activity limit of tritiated water which may be transported as LSA-II is raised above 0.8 TBq kg -1 , the resulting dose in accident conditions would not be unacceptable. (author)

Radioecology of tritiated water in subarctic soils and vegetation

International Nuclear Information System (INIS)

Salonen, L.; Miettinen, J.K.

1982-01-01

The residence times of tritium in various types of soils and plants have been determined in southern and northern Finland. The experiments were conducted in forest and agricultural environments where tritiated water was applied to the soil surface in the form of a single fall of rain. After that the movement and loss of tritiated water from the unsaturated zone was followed over a 2-4-year period in some forest areas. Uptake and loss of tritium in the tissue-free water and organic compounds of some native plants was studied in each area. The results indicated that in the subarctic area the half-residence times of tritium in soils and plants were greatly dependent on the climatic conditions at the time of the labelling and during the short growing seasons and also on the rate of water movement in the soil. In the experiments started during the best growing season the half-residence times in soil and plants do not differ from those determined in more temperate latitudes. (author)

Endothelial cell permeability to water and antipyrine

International Nuclear Information System (INIS)

Garrick, R.A.

1986-01-01

The endothelium provides a structural barrier between plasma constituents and the tissues. The permeability characteristics of the the endothelial cells regulate the transcellular movement of materials across this barrier while other movement is paracellular. In this study the permeability of the endothelial cells to tritiated water ( 3 HHO) and 14 C-labeled antipyrine (AP) was investigated. The cells were isolated non-enzymatically from calf pulmonary artery and were maintained in culture and used between the seventh and fifteenth passage. The cells were removed from the T-flasks with a rubber policeman, titurated with a 22g needle and centrifuged. The cells were mixed with an extracellular marker, drawn into polyethylene tubing and packed by centrifugation for use in the linear diffusion technique. All measurements were made at 37 C. The diffusion coefficients for 3 HHO through the packed cells (D), the intracellular material (D 2 ), and the extracellular material (D 1 ) were 0.682, 0.932 and 2.45 x 10 -5 cm 2 s -1 and for AP were 0.273, 0.355 and 1.13 x 10 -5 cm 2 s -1 respectively. The permeability coefficient calculated by the series-parallel pathway model for 3 HHO was higher than that for AP and for both 3 HHO and AP were lower than those calculated for isolated lung cells and erythrocytes

A study of water in glass by an autoradiographic method that utilizes tritiated water

International Nuclear Information System (INIS)

Knickerbocker, S.H.; Brown, S.D.; Joshi, S.B.

1983-01-01

This chapter determines water concentration and spatial distribution in glass by an autoradiographic method that makes use of tritiated water as the tagged species. Describes the method and presents some typical results. Lists advantages and disadvantages associated with the method and examines other methods that might be used for the study of water in glass. Discusses dry glass preparation, the addition of tritiated water to glass, glass preparation, film selection, and film analysis. Shows tritium autoradiography to be a valuable technique for measuring the content and spatial distribution of water in inorganic glasses. Finds that the technique yields unique information, particularly in regard to spatial distribution, when compared with techniques of IR spectroscopy, SIMS, SIPS, NRRA, ESR and NMR. Points out that large areas (e.g., several square inches) of sample can be mapped in a single exposure. Notes that the spatial resolution of water in the glass network can be 10 -7 m, so very accurate diffusion profiles are obtainable

Measurement of HTO permeability of materials for protective appliances

International Nuclear Information System (INIS)

Yamamoto, H.; Tomooka, M.; Kato, S.; Murata, M.; Kinouchi, N.; Yamamoto, H.

1992-01-01

Tritiated water (HTO) vapor permeabilities were measured for plastic and rubber films used for protective appliances (suits, gloves, wrappings, etc.). The measurement data prove that polyehylene and butyl rubbers are materials suitable for HTO protective appliances with their lower permeability. The data also indicate that desiccating protective appliances before reuse is effective for restoring their original resistances to penetrating HTO vapor when they are repeatedly used. (author)

Impact analysis and testing of tritiated heavy water transportation packages including hydrodynamic effects

International Nuclear Information System (INIS)

Sauve, R.G.; Tulk, J.D.; Gavin, M.E.

1989-01-01

Ontario Hydro has recently designed a new Type B(M) Tritiated Heavy Water Transportation Package (THWTP) for the road transportation of tritiated heavy water from its operating nuclear stations to the Tritium Removal Facility in Ontario. These packages must demonstrate the ability to withstand severe shock and impact scenarios such as those prescribed by IAEA standards. The package, shown in figure 1, comprises an inner container filled with tritiated heavy water, and a 19 lb/ft 3 polyurethane foam-filled overpack. The overpack is of sandwich construction with 304L stainless steel liners and 10.5 inch thick nominal foam walls. The outer shell is 0.75 inch thick and the inner shell is 0.25 inch thick. The primary containment boundary consists of the overpack inner liner, the containment lid and outer containment seals in the lid region. The total weight of the container including the 12,000 lb. payload is 36,700 lb. The objective of the present study is to evaluate the hydrodynamic effect of the tritiated heavy water payload on the structural integrity of the THWTP during a flat end drop from a height of 9 m. The study consisted of three phases: (i) developing an analytical model to simulate the hydrodynamic effects of the heavy water payload during impact; (ii) performing an impact analysis for a 9 m flat end drop of the THWTP including fluid structure interaction; (iii) verification of the analytical models by experiment

urea space versus tritiated water space as an in vivo predtctor

African Journals Online (AJOL)

Kock (1973) consider urea space in the ruminant to be a measure of empty body water (total body water less the water in the digestive tract) rather than total body water. The study reported in this paper evaluates the pros and cons of urea space measurement as compared to tritiated water space measurement in terms of ...

The estimation of annual limit on intake for tritiated food

International Nuclear Information System (INIS)

Komatsu, Kenshi; Okumura, Yutaka

1992-01-01

Tritium incorporation into tissues and DNA of mice was studied after daily ingestion of tritiated food or tritiated water. The tritiated food used was a commercial preparation mixed with brine shrimp which had been reared in tritiated sea water. After ingestion of tritiated food or water for up to 22 d, the specific activity of tritium in tissues was measured as tissue-free-water tritium, tissue-bound tritium and DNA-bound tritium. In order to compare the tritium intake from food with that from water, 14 C-glucose was added to food and drinking water. The specific activity of tritium of tissues obtained was then corrected by the specific activity of 14 C in tissues in order to analyse the tritium incorporation from the same amount of ingested food and water. DNA-bound tritium after the ingestion of tritiated food was 4.6 times higher than that of tritiated water, while tissue-bound tritium was 2.2 times higher. The radiation dose to liver from tritium incorporated through food was two-fold higher than through tritiated water, which was mainly due to the high incorporation of tritium into DNA. Our results demonstrated that the dose calculation based on tissue-free-water tritium alone would underestimate the radiation exposure of the human population exposed to tritiated food. (author)

Studies on tritium (tritiated water) mutagenicity and teratogenicity in rats

International Nuclear Information System (INIS)

Yagova, A.Kh.

1979-01-01

Single parental exposures to a range of tritium (tritiated water) activities, injecterd intraperitoneally, were used to study induction of genetic damage and effects on prenatal development in rats. In the male, treatment of postmeiotic stages of spermatogenesis was found to produce genetic damage, as judged by the dominant lethality test, at activity levels of the order of 1.0 microcurie/g body weight and above; when treating spermatogonia, no genetic damage was detected by this test. In the female, induced dominant lethality was observed after exposing oocytes in growing follicles to a tritium activity level of 10 microcurie/g b.w. Cytogenetic analysis of spermatocytes in meiosis disclosed increased frequency of reciprocal translocations after exposure of premeiotic cells (spermatogonia) to activities above 7 microcurie/g b.w., the effect tending to rise with increase in activity aministered per gram of body weight. Maternal treatment during early pregnancy was shown to raise prenatal death rate only at activities above 0.1 microcurie/g b.w; with such low activities, no discernible effects on postnatal development were noted, judging by postnatal death rate and increase in offspring body weight with time. In conclusion, experimental evidence was obthained that a tritiated water activity level of 0.1 microcurie per gram body weight (which is one order of magnitude above the annual limit of intake of tritiated water for members of the public) appears to produce no mutagenic effect and exert no influence upon the embryo

Conversion of tritium gas to tritiated water in the environment

International Nuclear Information System (INIS)

Noguchi, Hiroshi; Kato, Shohei

1985-01-01

The literature on conversion of tritium gas to tritiated water in various environments is reviewed. The conversion mechanisms and the conversion rates are as follows. 1. In the oxidation with oxygen and the isotopic exchange with water, tritium β-rays and metal catalyst are effective. The oxidation rate is ∼ 0.02 %/day at initial tritium concentration ≤ 10 -2 Ci/l and ∼ 2 %/day at 1 Ci/l. In the presence of oxygen and water, it is not clear whether the exchange reaction occurs or not because of the small amount of data. 2. For biological conversion, soil microorganisms contribute significantly. The conversion rate is greater than 10 %/hr. The tritium gas deposition velocity, which includes the uptake rate of tritium gas by soil and the conversion rate, ranges from 0.0025 to 0.11 cm/sec and is influenced by temperature and moisture of the soil. 3. Tritium gas is converted to the tritiated water through the reaction with hydroxyl radical produced by sunlight in the atmosphere. (author)

Comparative stochastic effects from low level exposure of mice to tritiated water

International Nuclear Information System (INIS)

Mewissen, D.J.; Ugarte, A.S.; Rust, J.H.

1987-01-01

A total of 1,133 C57 Black/6M mick of both sexes were randomly assigned to 5 experimental groups. In the first group, mice received a single injection of tritiated water (HTO) at weaning time. In the second group, weaned mice were exposed to tritated drinking water for the entire lifespan. In the third group the female parent received one single injection of HTO following delivery. In the fourth group, the female parent and her progeny were exposed to tritiated drinking water for the entire lifespan. In the fifth group, dams were exposed to tritiated drinking water from the beginning of pregnancy for the entire lifespan. (Drinking HTO 1 μCi/ml; single dose of HTO 1 μCi). Data from experimental groups were statistically evaluated vis a vis extensive control groups (+- 1,000 control mice of either sex). All mice were autopsied as moribund or soon after death and tissues were microscopically examined. A significantly increased incidence of reticulum cell sarcomas was observed in female offspring from dams in the third and fifth groups. A significantly increased incidence of hepatic tumors was observed in male offspring in the fourth group. Mean survival times did not significantly differ within experimental groups but were significantly different from controls

Conditioning of tritiated wastes. Part II

International Nuclear Information System (INIS)

Hawthorne, S.H.

1984-01-01

Work is continuing on the development of conditioning systems for low and intermediate level tritiated liquid and solid wastes which will prevent loss of tritium for at least 150 years. This portion of the program has concentrated on solidification and encapsulation of tritiated aqueous wastes, development of techniques, for the measurement of tritium loss in air and water, and identification and evaluation of encapsulation materials. Solidification of tritiated aqueous wastes by water extendible polyester or cements resulted in average tritium releases of approximately 1-4x10 -1 α/day with that from water extendible polyester being the lowest. The daily release rate is independent of initial tritium concentration in the waste form and can be reduced by a factor of 1000 by encapsultation of the waste within a 10 mm layer of water extendible polyester. Water extendible polyester is the preferred material for solidification and encapsulation of aqueous tritiated wastes and encapsulation of tritiated solids permitting release of only 3x10 -3 % of the original activity over 150 years. It is expected that this program which was originally scheduled for three years can now be completed in two years with complete definition of the conditioning system including the outer package

Internal dosimetry of tritiated hydrogen gas

International Nuclear Information System (INIS)

Peterman, B.F.; Johnson, J.R.; Dunford, D.W.; McElroy, R.G.C.

1985-02-01

This document is a report on experiments to quantify the doses that may occur from the tritium gas that is converted 'in vivo' to tritiated water following the exposure to tritiated hydrogen gas contaminated air. This report also includes theoretical evaluation of the radiological hazards from the uptake through skin of tritium from tritiated hydrogen adsorbed on surfaces

Uptake of tritiated lysine by fresh water alga, Scenedesmus obliquus

International Nuclear Information System (INIS)

Gogate, S.S.; Krishnamoorthy, T.M.

1983-01-01

Tritium uptake by fresh water alga. S.obliquus was studied using tritium labelled lysine, and a sequential solvent extraction procedure was used to study the distribution of tritium in different organic constituents of the algal cells. The accumulation of tritium in the algal cells was found to be 3-4 orders of magnitude more than that obtained for tritiated water. (author)

Genetic and somatic effects in animals maintained on tritiated water

International Nuclear Information System (INIS)

Carsten, A.L.; Brooks, A.; Commerford, S.L.; Cronkite, E.P.

1981-01-01

The possible genetic (dominant lethal mutations (DLM) and cytogenetic changes in the regenerating liver) and somatic (hematopoietic stem cell changes, growth and nonspecific life time shortening) effects in mice maintained on tritiated water (HTO) over two generations was investigated. Results to date are summarized

Can tritiated water-dilution space accurately predict total body water in chukar partridges

International Nuclear Information System (INIS)

Crum, B.G.; Williams, J.B.; Nagy, K.A.

1985-01-01

Total body water (TBW) volumes determined from the dilution space of injected tritiated water have consistently overestimated actual water volumes (determined by desiccation to constant mass) in reptiles and mammals, but results for birds are controversial. We investigated potential errors in both the dilution method and the desiccation method in an attempt to resolve this controversy. Tritiated water dilution yielded an accurate measurement of water mass in vitro. However, in vivo, this method yielded a 4.6% overestimate of the amount of water (3.1% of live body mass) in chukar partridges, apparently largely because of loss of tritium from body water to sites of dissociable hydrogens on body solids. An additional source of overestimation (approximately 2% of body mass) was loss of tritium to the solids in blood samples during distillation of blood to obtain pure water for tritium analysis. Measuring tritium activity in plasma samples avoided this problem but required measurement of, and correction for, the dry matter content in plasma. Desiccation to constant mass by lyophilization or oven-drying also overestimated the amount of water actually in the bodies of chukar partridges by 1.4% of body mass, because these values included water adsorbed onto the outside of feathers. When desiccating defeathered carcasses, oven-drying at 70 degrees C yielded TBW values identical to those obtained from lyophilization, but TBW was overestimated (0.5% of body mass) by drying at 100 degrees C due to loss of organic substances as well as water

Tritiated 2-deoxy-D-glucose as a probe for cell membrane permeability studies

International Nuclear Information System (INIS)

Walum, E.; Peterson, A.

1982-01-01

Tritiated 2-deoxy-D-glucose was taken up and phosphorylated by cultured cells of neuronal (NIE 115), glial (138 MG), muscle (L 6) and liver (BRL 123) origin. Upon perfusion the cells slowly released 2-deoxy-D-glucose 6-phosphate. The following values for rate constants, half-lives, and activation energies for the efflux were obtained: NIE 115: 0.0048 min -1 , 143 min, and 72 kJ mol -1 ; 138 MG: 0.0013 min -1 , 547 min, and 85 kJ mol -1 ; L 6: 0.0022 min -1 , 311 min, and 60 kJ mol -1 ; and BRL 123: 0.0013 min -1 , 528 min and 63 kJ mol -1 . When the cultures were perfused with buffer containing Triton X-100 a time- and concentration-dependent increase in the rate of efflux of 2-deoxy-D-glucose 6-phosphate was obtained. It is suggested that 2-deoxy-D-[ 3 H]glucose can be used as a probe in studies of general cell membrane permeability changes

Comparison of late effects of single x-ray exposure, chronic tritiated water ingestion, and chronic cesium-137 gamma exposure in mice

International Nuclear Information System (INIS)

Carsten, A.L.; Cronkite, E.P.

1979-01-01

There is concern over the possible late effects resulting from chronic exposure to tritiated water, a primary by-product of power reactors. We are comparing the genetic and somatic effects of tritiated water ingestion to acute x-ray or chronic cesium-137 gamma-ray exposures. Eight week old mice were maintaned on tritiated water in concentrations of 0.3, 1.0, and 3.0 μCi/ml. Identical animals received cesium-137 gamma exposures equivalent to that from the tritiated water. At 4 week intervals, animals were sacrificed and the hematopoietic stem cell content and cellularity of the bone marrow determined. For comparison of acute and chronic effects, one group of mice received a single whole-body x-ray exposure of 525 rads. The x-irradiated animals showed an immediate sharp decrease in marrow cellularity followed by gradual return to normal levels, with a lifelong reduction in number of marrow stem cells. Animals exposed to the two higher concentrations of tritiated water showed only slight reductions in marrow cellularity, with a lifelong reduction in hematopoietic stem cells in the bone marrow. Comparison of the external gamma exposures to chronic tritiated water ingestion indicates similar patterns. Maintenance of normal cellularity with a reduced number of stem cells in x-rayed animals was shown by tritiated thymidine cytocide to be due to the reduction in number of stem cells in the resting G/sub O/ stage. At this time it is not possible to determine whether there is a significant difference in relative biological effectiveness of tritiated water compared to cesium-137 gamma rays; however, indications are that they are similar

Evaluation of absorbed doses at the interface solid surfaces - tritiated water solutions

International Nuclear Information System (INIS)

Postolache, Cristian; Matei, Lidia

2003-01-01

Studies concerning the isotopic exchange H/D/T in the system elemental hydrogen -- water and in the presence of platinum metals on hydrophobic supports as catalysts were carried out at ICSI (Institute of Cryogenics and Isotope Separations) - Rm. Valcea, Romania. Due to the very low energy of β-radiation emitted by tritium, the direct measurements of dose absorbed by the isotopic exchange catalyst using classical methods is practically impossible. For this purpose an evaluation model was developed. The volume of tritiated water which can irradiate the catalyst was represented by a hemisphere with the radius equal to the maximal rate of β-radiation emitted by tritium. The catalyst surface is represented by a circle with a 0.2 μm radius and the same centre as the circle of the hemisphere secant plane. Flow rate of absorbed dose is calculated with the relation: d (1/100)(Φ·E m /m), where d = dose flow rate, in rad/s, Φ total radiation flux interacting with the catalyst surface, expressed in erg and m = catalyst weight, in grams. Total flux of available radiation, Φ, was determined as a function of three parameters: a) total flow of tritium β-radiation emitted in the hemisphere of tritiated water, dependent on the volume and radioactive concentration; b) emission coefficient in the direction of the catalyst surface; c) attenuation coefficient (due to self-absorption) of the tritium β-radiation in the tritiated water body. (authors)

Relative transport of water (H2O) and tritiated water (HTO) across cellulose acetate (CA) membranes

International Nuclear Information System (INIS)

Prabhakar, S.; Misra, B.M.; Ramani, M.P.S.

1986-01-01

The relative transport characteristics of water (H 2 O) and tritiated water (HTO) were evaluated through cellulose acetate membranes under osmosis, reverse osmosis and pervaporation. The results indicate that the relative transport is independent of the process. The anamolous observations under osmotic conditions are explained. (orig.)

Studies on the fixation of tritiated water using the cement hydration, 2

International Nuclear Information System (INIS)

Nishimaki, Kenzo; Tsutsui, Tenson; Miake, Chiaki.

1989-01-01

In the previous paper, we have reported the results of basic experiments to fix tritiated water using the hydration of cement, and found that most tritiated water transfers to surrounding water, even if it is incorporated using the hydration of cement. In this report, we tried to apply a simple compartment model to the tritium transfer curves reported in the previous paper, which represent the phenomena that most water containing tritium is exchanging with a surrounding water, regardless of its forms, i.e., a crystalline water, free water and so on. We divided a solidified cement into three groupes with respect to the exchangeability of water, i.e., a compartment of fixed water, of compositions expect water, and of exchanging water. We developed a simple compartment model under the assumption that the water in the third compartment is exchangeable with the sorrounding water with a certain exchanging volume rate E, not altering by time. The transfer curves calculated with the model contains unknown parameter, E. By the method of least squares, varying the values of E, we could obtain most approximated transfer curves of tritium to those obtained by the previous experiments. In the result, we knew that the simple compartment model is applied to the tritium transfer curves reported in the previous paper. (author)

Detection of the contamination of air by tritiated water vapour around the reactor EL3

International Nuclear Information System (INIS)

Lebouleux, P.; Ardellier, A.; Valero, S.

1968-01-01

The authors describe the apparatus used for the detection of the tritiated water vapour contamination in the air around the reactor EL 3. The apparatus consists of two air-circulation ionisation chambers; the air in one of these is dried by passage through a silica-gel column. By carrying out a differential measurement of the ionization currents, it is possible to measure the tritiated water vapour concentration. A theoretical study of the response of the chambers is carried out for two types of emission of the tritiated water vapour: continuous, or in bursts. The experimental work comprises: calibration in the measurement range employed; study of the selectivity for other active gases; study of typical accidents; the interpretation of the results in the case of discontinuous emission, taking into account the desorption from the walls of the measurement chamber, a phenomenon which is observed during the emptying process. The authors give finally actual examples of how to use the results. The apparatus built makes it possible to detect, in less than ten minutes, contamination by tritiated water vapour in the presence of other active gases, in a measurement range of between 3 and 2200 MPC, and with an accuracy of about 25 per cent. A transposition to calculations of the risk to workers should be made with the utmost caution; an envelope of this risk can be drawn up more or less accurately depending on particular cases. (authors) [fr

Induction of malignant transformation in CHL-1 cells by exposure to tritiated water

International Nuclear Information System (INIS)

Zou Shu'ai; Wang Hui

1992-01-01

The induction of neoplastic transformation in CHL-1 cells by low-dose-rate exposure to tritiated water was reported. CHL-1 cells were exposed to tritiated water (9.25 x 10 5 - 3.7 x 10 6 Bq/mL) for 24-96 hours and the accumulated doses were estimated to be 0.055-0.88 Gy, respectively. Neoplastic transformation was found in all exposed cell groups. The morphological study and transplantation test was carried out for demonstration malignancy of the transformed cells and the results show that they are with the morphology and behaviour for malignant tumour cells. For CHL-1 cells exposed to various doses of tritiated water, transformation rates were found to be from 3.28% to 13.0% at dose of 0.055-0.88 Gy. In order to estimate RBE of tritium for malignant transformation in CHL-1 cells, the induction of malignant transformation in CHL-1 cells by exposure to 137 Cs gamma-rays was carried out at dose rates of 0.359 Gy/24 hr and transformation rates for irradiated CHL-1 cells were found to be from 2.59% to 13.4%. Based on these data, RBE of tritium for malignant transformation in CHL-1 cells was estimated to be 1.6

Tritium incorporation in corn and bean after an accute contamination with tritiated water

International Nuclear Information System (INIS)

Silva, H.A.; Archundia, C.; Bravo, G.; Nulman, R.; Ortiz Magana, J.R.

1979-01-01

Tritium produced by natural or artificial processes is set free in the environment, generally as tritiated water, which the plants use to produce organic compounds such as proteins, fats and carbohidrates. The metabolism of tritium depends on the chemical form in which it is found, transport studies of tritium in different ecosystems, and in particular in food chains, gradually have become more important as a result of the tritium increase in the environment. In Mexico, corn and beans have been studied due to their great importance in the human food chain. The determination of tritium in organic compounds (bound tritium) requires an efficient conversion to tritiated water. For this reason, in this work we have detailed a dry oxidation method, which is a modification of the method of Schoniger, which consists of combustion in oxygen initiated by a simple electrical device using a disposable nichrome resistance, which is also used as a sample carrier. Tritium determination is done by a liquid scintillation counter with quenching correction using an internal standard. Graphs of tritium activity are shown plotted against the time between the application of tritiated water and the time of harvest. The highest activity is found about the 18th day for corn and the 16th day for beans. The calculated values for the half-lives for corn and beans are approximately 56 and 43 days respectively. (author)

Light and ultrastructural studies on liver of Oreochromis niloticus fry grown in tritiated water during embryonic development

Energy Technology Data Exchange (ETDEWEB)

Carino, V S; Alvendia-Casauay, A [Institute of Biology, College of Science, University of the Philippines, Diliman, Quezon City (Philippines)

1991-01-01

Oreochromis niloticus embryos of different developmental stages were reared in tritiated water at 3.7, 0.37, 0.037, and 0 GBq/1 and harvested at day 21 stage. In general, gross morphology of liver was altered in fry reared in higher tritium concentrations and in fry reared in tritiated water at earlier stages of development. Under light microscopy, fatty infiltration of liver parenchyma, presence of unresorped yolk sac, occasional vacuolation in cytoplasm of hepatocytes, widening of sinusoids, and increased size of space of Disse were observed in liver of fry reared in tritiated water at higher concentrations. At the electron microscope level, swollen mitochondria, fragmented rough endoplasmic reticulum, and insconspicuous glycogen granules compared to control were noted in liver of treated fish. This study give basic information on how cells may be affected by irradiation at the histological, cellular, and subcellular level. (auth.). 8 figs.; 1 tab.

Ratio of tritiated water and hydrogen generated in mercury through a nuclear reaction

Energy Technology Data Exchange (ETDEWEB)

Manabe, K. [Nuclear Science and Engineering Directorate, Japan Atomic Energy Agency (JAEA), Tokai, Naka-gun, Ibaraki 319-1195 (Japan)], E-mail: manabe.kentaro@jaea.go.jp; Yokoyama, S. [Nuclear Science and Engineering Directorate, Japan Atomic Energy Agency (JAEA), Tokai, Naka-gun, Ibaraki 319-1195 (Japan)

2008-02-15

Tritium generated in a mercury target is a source of potential exposure of personnel at high-energy accelerator facilities. Knowledge of the chemical form of tritium is necessary to estimate the internal doses. We studied the tritium generation upon thermal neutron irradiation of a mercury target modified into liquid lithium amalgam to examine the ratio of tritiated water ([{sup 3}H]H{sub 2}O) and tritiated hydrogen ([{sup 3}H]H{sub 2}). The ratio between [{sup 3}H]H{sub 2}O and [{sup 3}H]H{sub 2} generated in lithium amalgam was 4:6 under these experimental conditions.

Recycle attuned catalytic exchange (RACE) for reliable and low inventory processing of highly tritiated water

International Nuclear Information System (INIS)

Iseli, M.; Schaub, M.; Ulrich, D.

1992-01-01

The detritiation of highly tritiated water by liquid phase catalytic exchange needs dilution of the feed with water to tritium concentrations suitable for catalyst and safety rules and to assure flow rates large enough for wetting the catalyst. Dilution by recycling detritiated water from within the exchange process has three advantages: the amount and concentration of the water for dilution is controlled within the exchange process, there is no additional water load to processes located downstream RACE, and the ratio of gas to liquid flow rates in the exchange column could be adjusted by using several recycles differing in amount and concentration to avoid an excessively large number of theoretical separation stages. In this paper, the flexibility of the recycle attuned catalytic exchange (RACE) and its effect on the cryogenic distillation are demonstrated for the detritiation of the highly tritiated water from a tritium breeding blanket

Tritium in organic compounds of brain of rats exposed to tritiated water or tritiated food during three successive generations

International Nuclear Information System (INIS)

Major, Z.

1987-01-01

The study was performed on Wistar rats which were chronically exposed to tritiated water (HTO, 37.0 kBq/ml) or to tritiated food (48.1 kBq/g). The tritium exposure of the rats was started before mating and was continued up to delivery of the F 3 generation. The incorporation of organically bound tritium (OBT) was determined in whole brain and in some organic components of rats at various ages. The specific activity of OBT in whole brain and in its organic components with the exception of proteins significantly increased in the F 1 +F 2 generations of rats in comparison with F 0 females. The contribution of OBT to the total dose rate was about 6 per cent in HTO group and 9 per cent in T-food group. The contribution of lipids and proteins to the dose rate from OBT was similar in both treatment groups, being 60 and 20 per cent, respectively. 20 refs. (author)

Hydration of DNA by tritiated water and isotope distribution: a study by 1H, 2H, and 3H NMR spectroscopy

International Nuclear Information System (INIS)

Mathur-De Vre, R.; Grimee-Declerck, R.; Lejeune, P.; Bertinchamps, A.J.

1982-01-01

The hydration layer of DNA (0.75%) in tritiated water represents 3.5% of solvent 3 HHO. The combined effects of temperature (-6 to -40 0 C) and H 2 O/ 2 H 2 O solvent composition on the spin-lattice relaxation times of water protons and deuterons suggest selective distribution of isotopes in the hydration layer. The ''hydration isotope'' effect and the localization of tritiated water molecules in the hydration layer of DNA have important implications in describing the radiobiological effects of tritiated water because the initial molecular damage caused by 3 HHO (internal radiation source) localizes close to 3 H due to the short range and low energy of 3 H β rays

Distribution of tritiated compounds (tritiated thymidine and tritiated water) in the mother-fetus system and its consequences for the radiotoxic effect of tritium

Energy Technology Data Exchange (ETDEWEB)

Schreml, W; Fliedner, T M [Ulm Univ. (Germany, F.R.). Abt. Klinische Physiologie

1978-01-01

The incorporation and distribution of tritiated thymidine (/sup 3/H-TdR) and tritiated water (HTO) have been measured in newborn rats exposed to various levels of tritium by continuous infusion into pregnant rats from day 9 until term. In the animals exposed to HTO, the tritium activity was homogeneously distributed while /sup 3/H-TdR led to accumulation of DNA-bound and homogeneously distributed tritium. The incorporated activity and the specific activity of DNA from ovaries which showed a reduction of total oocyte number by approximately 50% were used to estimate the dose absorbed by the ovarian cell nuclei in both systems. From the absorbed dose a factor of 3.7 was calculated for the 'internal relative biological effectiveness' of DNA-bound tritium as compared to homogeneously distributed /sup 3/H under the restrictive assumption that the static description of the system at birth reflects the situation during the time of dynamic development of the ovaries when the toxic effect occurs. The influence of these dynamic factors of changing nuclear size and tritium incorporation during the sensitive period is weighed against the possibility that the continuous /sup 3/H-TdR infusion during pregnancy might represent a model in which DNA-bound tritium shows a higher effectiveness than homogeneously distributed tritium.

Tritiation methods and tritium NMR spectroscopy

International Nuclear Information System (INIS)

Jaiswal, D.K.; Morimoto, H.; Salijoughian, M.; Williams, P.G.

1991-09-01

We have used a simple process for the production of highly tritiated water and characterized the product species by 1 H and 3 H NMR spectroscopy. The water is readily manipulated and used in subsequent reactions either as T 2 O, CH 3 COOT or CF 3 COOT. Development of tritiated diimide has progressed to the point where cis-hydrogenated products at 1-20 Ci/mmole S.A. are possible. Tri-n-butyl tin tritide has been produced at >95% tritium content and well characterized by multinuclear NMR techniques. 27 refs., 3 figs

Crypt cell population kinetics in mouse jejunum under continuous beta irradiation from tritiated water

International Nuclear Information System (INIS)

Bhatia, A.L.; Gupta, M.L.; Saharan, B.R.

1979-01-01

The behaviour of crypt cell population in mouse jejunum under continuous beta irradiation from tritiated water (HTO) has been studied. Adult mice were maintained on tritiated drinking water of the activity of 1.25 μCi/ml, after priming injection. The crypts were studied at 1, 5, 7, 15 and 30 days after the initiation of treatment. It is observed that there is a partial recovery in proliferative activity after the first day of the treatment. Again there is a decrease in the crypt cells on the 7th day, after which this population appears to achieve a near-steady-state level at about 8% below normal at the last interval studied. Crypt cell population and mitotic figures showed a simultaneous dip and recovery, while dead cells showed inverse relationship. (orig.) [de

Processing Tritiated Water at the Savannah River Site: A Production-Scale Demonstration of a palladium membrane reactor

International Nuclear Information System (INIS)

Sessions, K

2004-01-01

The Palladium Membrane Reactor (PMR) process was installed in the Tritium Facilities at the Savannah River Site to perform a production-scale demonstration for the recovery of tritium from tritiated water adsorbed on molecular sieve (zeolite). Unlike the current recovery process that utilizes magnesium, the PMR offers a means to process tritiated water in a more cost effective and environmentally friendly manner. The design and installation of the large-scale PMR process was part of a collaborative effort between the Savannah River Site and Los Alamos National Laboratory. The PMR process operated at the Savannah River Site between May 2001 and April 2003. During the initial phase of operation the PMR processed thirty-four kilograms of tritiated water from the Princeton Plasma Physics Laboratory. The water was processed in fifteen separate batches to yield approximately 34,400 liters (STP) of hydrogen isotopes. Each batch consisted of round-the-clock operations for approximately nine days. In April 2003 the reactor's palladium-silver membrane ruptured resulting in the shutdown of the PMR process. Reactor performance, process performance and operating experiences have been evaluated and documented. A performance comparison between PMR and current magnesium process is also documented

Selected bibliography on heavy water, tritiated water and hydrogen isotopes (1981-1992)

International Nuclear Information System (INIS)

Gopalakrishnan, V.T.; Sutawane, U.B.; Rathi, B.N.

1994-01-01

A selected bibliography on heavy water, tritiated water and hydrogen isotopes is presented. This bibliography covers the period 1981-1992 and is in continuation to Division's earlier report BARC-1192 (1983). The sources of information for this compilation are Chemical Abstracts, INIS Atom Index and also some scattered search through journals and reports available in our library. No claim is made towards exhaustiveness of this bibliography even though sincere attempts have been made for a wide coverage. The bibliography is arranged under the headings: (1) production, purification, recovery, reprocessing and storage, (2) isotope exchange, 3) isotope analysis, (4) properties and (5) miscellaneous. Total number of references in the bibliography are 1762. (author)

Demonstration on endurance of ion exchange membrane immersed in high-concentration tritiated water under the Broader Approach Activities

Energy Technology Data Exchange (ETDEWEB)

Iwai, Yasunori, E-mail: iwai.yasunori@jaea.go.jp; Sato, Katsumi; Kawamura, Yoshinori; Yamanishi, Toshihiko

2013-10-15

Highlights: • Endurance of Nafion ion exchange membrane immersed in 1.38 × 10{sup 12} Bq/kg of highly concentrated tritiated water was demonstrated. • Degradation of Nafion backbone structure by tritium beta was similar to that by gamma rays and electron beams at an equivalent dose. • Degradation directly by radiation was dominant at room temperature compared with that by reactions with radicals produced from water radiolysis. -- Abstract: The Nafion{sup ®} ion exchange membrane is a key material for electrolysis cells of the water detritiation system. Endurance of Nafion ion exchange membrane immersed in 1.38 × 10{sup 12} Bq/kg of highly concentrated tritiated water has been demonstrated at room temperature for up to 2 years under the Broader Approach Activities. The curves of percent elongation at break vs. dose and tensile strength vs. dose for the Nafion membranes immersed in tritiated water were well consistent with those for Nafion membranes irradiated to an equivalent dose with gamma rays and electron beams. This shows that the degradation of Nafion backbone structure by tritium beta is similar to that by gamma rays and electron beams. The results of ferric Fenton test indicated that the degradation directly by radiation was dominant at room temperature compared with that by reactions with radicals produced from water radiolysis. The curve of ion exchange capacity vs. dose for the Nafion membranes immersed in tritiated water was also well consistent with that for Nafion membranes irradiated to an equivalent dose with gamma rays and electron beams. These results showed irradiation tests with gamma rays and electron beams were alternative for predicting degradation of ion exchange membrane by tritium beta.

Contributions of the CEA-Valduc Centre control to the understanding of the transfers of atmospheric tritiated water into the different parts of the environment

International Nuclear Information System (INIS)

Guetat, P.; Vichot, L.; Tognelli, A.

2009-01-01

After a description of the geological environment of the Valduc Centre dedicated to tritium purification and tritiated waste processing and storage, this document presents the assessment of quantities of tritiated water released by the Valduc Centre and of their evolution in the hydro-geological environment. It provides in situ macroscopically observed data on the transfer mechanisms of water into the different parts of the environment and into the food chain by means. This is made possible by the exceptional traceability of tritiated water. Finally, a comparison between computational models and experimental measurements is given

Tritiated water metabolism during dehydration and rehydration in the camel

International Nuclear Information System (INIS)

Etzion, Z.; Meyerstein, N.; Yagil, R.

1984-01-01

The metabolism of tritiated water in the camel was compared in two 10-day periods, one when water was readily available and the second during dehydration. There was a radically depressed metabolism after 2 days of dehydration. Two other experiments examined the absorption rate of drinking water. In one experiment drinking water was labeled with tritium, and in the second experiment dilution of tritium-labeled blood was examined. In both experiments there was a rapid uptake and dilution of the blood, which continued for 4 h. Following this only slight changes were observed up to 24 h after drinking. The results are in accord with other data showing changes in erythrocyte shape 4 h after rapid rehydration. It is concluded that there is a rapid absorption of water in the rehydrating camel

The metabolisme of tritiated water in the rat

International Nuclear Information System (INIS)

Jeanmaire, Lucien; Vernois, Yvette; Bullier, Denise; Gros, Roger.

1977-07-01

The metabolism of tritiated water was studied in the rat during 580 days. The results on urinary and fecal excretion, total activity retention in 25 tissues or organs, cumulated activities from the 4th to the 582nd day are presented and discussed. They are in agreement with other similar studies, if compared over the same length of experimentation. The activity retained by the spinal cord is twice that retained in the brain considered as the organ whose long half-lived component is the most active. The use of such data for the study of tritium-labelled compounds is illustrated by two examples [fr

Solid oxide electrolysis cell for decomposition of tritiated water

International Nuclear Information System (INIS)

Konishi, S.; Katsuta, H.; Naruse, Y.; Ohno, H.; Yoshida, H.

1984-01-01

The decomposition of tritiated water vapor with solid oxide electrolysis cell was proposed for the application to the D-T fusion reactor system. This method is essentially free from problems such as large tritium inventory, radiation damage, and generation of solid waste, so it is expected to be a promising one. Electrolysis of water vapor in argon carrier was performed using tube-type stabilized zirconia cell with porous platinum electrodes in the temperature range of 500 0 C to 950 0 C. High conversion ratio from water to hydrogen up to 99.9% was achieved. The characteristics of the cell is deduced from the Nernst's equation and conversion ratio is described as the function of the open circuit voltage. Experimental results agreed with the equation. Isotope effect in electrolysis is also discussed and experiments with heavy water were carried out. Obtained separation factor was slightly higher than the theoretical value

Genetic and somatic effects in animals maintained on tritiated water

International Nuclear Information System (INIS)

Carsten, A.L.; Commerford, S.L.; Cronkite, E.P.; Brooks, A.

1982-01-01

Somatic and genetic effects of the continuous ingestion of tritiated water (HTO) at concentrations of 0.3, 1.0 and 3.0 μCi/ml were investigated in mice of the Hale-Stoner-Brookhaven strain. At these levels, there was no measurable somatic effect. Although genetic effects as measured by dominant lethal mutation (DLM) assay indicated a significant effect (P>0.01) on the number of viable embryos and early deaths in the 3.0 μCi/ml HTO group and on the number of viable embryos in the 1.0 μCi/ml HTO group, no genetic effects were significantly noted in the 0.3 μCi/ml HTO group. Liver cytogenetic studies showed a significant increase in the number of abnormal cells in the 3.0 μCi/ml HTO group. A reduction in bone marrow stem cells, without an attendant reduction in total marrow cellularity, was noted in the 3.0 and 1.0 μCi/ml HTO groups. There was no significant difference in any of the DLM parameters between animals maintained on 3.0 μCi/ml of HTO and animals exposed to the equivalent 137 Cs gamma dose (22 hours/day exposure). Consideration of the relative amounts and biological half lives of tritium present in the nucleus as water, DNA and histone suggests that after transient exposure to tritiated water, nearly all significant radiation damage can be attributed to tritium present in the nucleus as water. These data suggest that hazards from tritium attendant with normal reactor operation should not at this time be considered as a deterrent to the further development of fission and/or fusion reactor technology. (Namekawa, K.)

An overview of SCK-CEN's technological research for the treatment of tritiated waste

International Nuclear Information System (INIS)

Braet, J.; Bruggeman, A.; Vanderbiesen, S.

2004-01-01

The production of fusion energy involves the use of huge amounts of tritium, of the order of 4 x 10 19 Bq/Gwe.a. Therefore operation and dismantling of test installations and future commercial fusion reactors are not possible without the production of tritiated waste. Various categories of tritiated waste are and will be produced which require different detritiation techniques to lower the initial tritium content in the samples and to allow final waste disposal of the partly detritiated material and of all by-products generated in the processes. The current internationally adopted strategy is to convert all kinds of tritiated waste into tritiated water, which can then be treated in one water detritiation installation. Since several years SCK-CEN has been developing techniques for the treatment of tritiated waste. Amongst them technologies for the treatment of tritiated organic liquids, surface contaminated metals, contaminated concrete and most importantly water detritiation. The so-called liquid phase catalytic exchange for water detritiation requires an efficient catalyst that should furthermore be hydrophobic because of the low solubility and hence slow diffusion of hydrogen in the water layer that covers normal catalysts. In the past SCK-CEN invented and developed such a catalyst which has recently been optimized and tested in a bench scale installation. To confirm the performances of our improved catalyst for a longer period of time and in a longer column, we are now doing tests in a 2 meter high trickle bed reactor and the endurance of the catalyst is being tested at ICSI. Using a good performing catalyst, LPCE will be, in combination with electrolysis, a technically and economically sound technology for water detritiation. Other R and D focuses on the development of a system do decontaminate surface contaminated metals and concrete using superheated steam. The resulting water can in its turn be treated in a water detritiation installation. For the purpose of

Laboratory studies conducted for the development of a plant to concentrate the radioactive waste from tritiated water

International Nuclear Information System (INIS)

Bornea, Anisia; Zamfirache, Marius; Stefanescu, Ioan; Vasut, Felicia; Soare, Amalia

2009-01-01

Full text: The Cernavoda Nuclear Power Plant is the biggest operational source of tritium, from Europe and one of the most important in the world. Our interest is especially focussed on tritiated water waste with low activity resulting from the maintenance operations performed on reactors with the purpose of reducing their volume and further reprocessing. The system presented in this work is based on the catalytic isotopic exchange and molecular dissociation CECE. The development of technologies in the field of isotopic separation based on the water electrolysis process was not very successful in last decades first of all because of the shortcomings of the classical electrolysers which use a KOH-type electrolyte. The main disadvantages are high KOH electrolyte hold-up and problems regarding hydrogen and oxygen purification and consequently the corrosion risk. Lately, there has been noticed a growing interest regarding the electrolysers having polymer membranes as electrolyte SPM (solid polymer membrane). Such an electrolyser is available in our institute, so the aim of our research was to use this electrolyser in a tritium concentration system from the tritiated water waste using the technology for isotopes separation-CECE. The present paper presents a conceptual design scheme for a concentration system of the tritium resulting from the tritiated water waste. (authors)

Improving distillation method and device of tritiated water analysis for ultra high decontamination efficiency

International Nuclear Information System (INIS)

Fang, Hsin-Fa; Wang, Chu-Fang; Lin, Chien-Kung

2015-01-01

It is important that monitoring environmental tritiated water for understanding the contamination dispersion of the nuclear facilities. Tritium is a pure beta radionuclide which is usually measured by Liquid Scintillation Counting (LSC). The average energy of tritum beta is only 5.658 keV that makes the LSC counting of tritium easily be interfered by the beta emitted by other radionuclides. Environmental tritiated water samples usually need to be decontaminated by distillation for reducing the interference. After Fukushima Nucleaer Accident, the highest gross beta concentration of groundwater samples obtained around Fukushima Daiichi Nuclear Power Station is over 1,000,000 Bq/l. There is a need for a distillation with ultra-high decontamination efficiency for environmental tritiated water analysis. This study is intended to improve the heating temperature control for better sub-boiling distillation control and modify the height of the container of the air cooling distillation device for better fractional distillation effect. The DF of Cs-137 of the distillation may reach 450,000 which is far better than the prior study. The average loss rate of the improved method and device is about 2.6% which is better than the bias value listed in the ASTM D4107-08. It is proven that the modified air cooling distillation device can provide an easy-handling, water-saving, low cost and effective way of purifying water samples for higher beta radionuclides contaminated water samples which need ultra-high decontamination treatment. - Highlights: • The improvements of method and device make the decontaminatin factor (DF) of Cs-137 of distillation reach over 450,000. • The decontamination factor ( DF) value may be increased about 20 times by increasing the height of the container from 7 cm to 20 cm. • The device provides an easy-handling, water-saving, low cost, stable and effective way for the distillation of triated water analysis.

Use of tritiated water as indicator of the water metabolism on normal and operate patients

International Nuclear Information System (INIS)

Fallot, P.; Aeberhardt, A.

1955-01-01

Water disruptions are very frequent during the medical and surgical affections. In order to study the kinetics of the water exchanges as well as the determination of the total water of the body, we have chosen tritiated water as indicator. This work presents a rapid process, faithful and sensitive of dosage of the Tritium in the biologic liquids. This method has been applied to the survey of the intestinal absorption of water among normal subjects and during some medical and surgical affections. The exam of the experimental curves permitted to get information concerning the kinetics of water ingested as well as of data on the volume of total water of the human body and on the biologic period of the Tritium in the organism. (M.B.) [fr

The use of tritiated water in evaluating animal production parameters

International Nuclear Information System (INIS)

Robertshaw, D.

1988-01-01

Tritiated water (TOH) provides a means of measuring a number of parameters of importance not only to the applied animal physiologist but to those involved in assessing animal productivity. For the examination of animal-environment interactions, TOH is an invaluable tool for assessing total body water, water turnover rate and hence water requirements of different types of animals kept under a variety of climatic and other conditions. It can also be useful for measuring water losses, e.g. through evaporation, and hence is a tool for assessing thermal stress. For animal productivity studies, TOH is useful for assessing such parameters as carcass composition, the intake of forages, supplements and milk. Each of these aspects is described as are the assumptions which have to be made when using TOH for the measurements concerned. (author). 11 refs, 1 tab

Biogenesis of tritiated and carbon-14 methane from low-level radioactive waste

International Nuclear Information System (INIS)

Francis, A.J.; Dobbs, S.; Doering, R.F.

1980-01-01

Methane bacteria were detected in leachate samples collected from commercial low-level radioactive waste disposal sites. Significant amounts of tritiated and carbon-14 methane were generated by a mixed methanogenic culture from a leachate sample collected from the low-level radioactive waste disposal site, Maxey Flats, KY. Tritiated methane was produced by methane bacteria from synthetic media containing 2 mCi of tritium as tritiated water or tritiated acetate, and the level of tritium added to the medium had no effect on methanogenesis. Under anaerobic conditions the organic compounds containing 14 C and 3 H activity and tritiated water in the waste are metabolized by microorganisms and they produce radioactive gases which escape into the environment from the disposal sites. 4 figures, 3 tables

Volatilized tritiated water vapor in the vicinity of exposed tritium contaminated groundwater

International Nuclear Information System (INIS)

Dunn, D.L.; Carlton, B.; Hunter, C.; McAdams, T.

1994-01-01

Water vapor tritium concentrations in air above a known source of tritiated water can be estimated. Estimates should account for the mechanisms of evaporation and condensation at the water surface and water species exchange, and are typically applicable under a broad range of wind, temperature and humidity conditions. An estimate of volatilized tritium water vapor was made for a known outcropping of tritium contaminated groundwater at the Savannah River Site (SRS) old F-Area effluent stream. In order to validate this estimate and the associated dose calculation, sampling equipment was fabricated, tested, and installed at the effluent stream. The estimate and the dose calculation were confirmed using data from samples collected

Solid oxide electrolysis cell for decomposition of tritiated water

International Nuclear Information System (INIS)

Konishi, S.; Ohno, H.; Yoshida, H.; Katsuta, H.; Naruse, Y.

1986-01-01

The decomposition of tritiated water vapor by means of solid oxide electrolysis cells has been proposed for the application to the D-T fusion reactor system. This method is essentially free from problems such as large tritium inventory, radiation damage, and generation of solid waste, so it is expected to be a promising one. Electrolysis of water vapor in an argon carrier was performed using a tube-type stabilized zirconia cell with porous platinum electrodes over the temperature range 500-950 0 C. High conversion ratios from water to hydrogen, of up to 99.9%, were achieved. The characteristics of the cell were deduced from the Nernst equation and the conversion ratios expressed as a function of the IR-free voltage. Experimental results agreed with the equation. The isotope effect in electrolysis is also discussed and experiments with heavy water were carried out. The obtained separation factor was slightly higher than the theoretical value. (author)

Calculation of committed dose equivalent from intake of tritiated water

International Nuclear Information System (INIS)

Law, D.V.

1978-08-01

A new computerized method of calculating the committed dose equivalent from the intake of tritiated water at Harwell is described in this report. The computer program has been designed to deal with a variety of intake patterns and urine sampling schemes, as well as to produce committed dose equivalents corresponding to any periods for which individual monitoring for external radiation is undertaken. Details of retrospective doses are added semi-automatically to the Radiation Dose Records and committed dose equivalents are retained on a separate file. (author)

Effects of tritiated water on mice liver, in relation to age

Energy Technology Data Exchange (ETDEWEB)

Bhatia, A L [Rajasthan Univ., Jaipur (India). Radiation Biology Lab.

1978-06-01

Tritiated water was administered intraperitoneally at the dose rate of about 20 ..mu..Ci/ml of body water to different six age groups of Swiss albino mice, ranging from 1 to 6 weeks old. They were autopsied at 48 hours post-injection. The liver of 5 weeks old mice is found most vulnerable and that of 4 weeks second but lesser than 5 weeks. Histopathologically, 1, 2, 3 and 6 weeks old mice liver showed lesser degree of damage. The distinct histopathological lesions include oedema, cytoplasmic vacuolation and degranulation, hyperaemia, increase number of Kupffer's cells etc.

Relative biological effectiveness of tritiated water on cultured mammalian cells at molecular and cellular level

International Nuclear Information System (INIS)

Okada, S.; Sakai, K.; Nakamura, N.

1986-01-01

Factors that affect RBE values have been investigated in cultured cells. It was shown that: (1) Different RBE values were obtained with the same tritiated water treated cells depending upon the biological end-point; this may be related to target size. (2) The RBE value for one end-point (e.g. cell killing) in different cell types was often different. In some cells, the RBE value increased with reducing dose; in other cells, the value remained constant. (3) The RBE value for tritiated water seemed to fit a general RBE-LET relationship. These results suggest that although the RBE value might vary from 1 to 2 when cells are exposed to HTO, there are situations where the value becomes higher than 2; these are associated with low dose and low dose rate exposures in some cell types. (author)

Gas generation by self-radiolysis of tritiated waste materials

International Nuclear Information System (INIS)

Tadlock, W.E.; Abell, G.C.; Steinmeyer, R.H.

1980-01-01

Studies simulating the effect of self-radiolysis in disposal packages containing tritiated waste materials show hydrogen to be the dominant gas-phase product. Pressure buildup and gas composition over various tritiated octane and tritiated water samples are designed to give worst case results. One effect of tritium fixation agents is to reduce pressure buildup. The results show that development of explosive gas mixtures is unlikely and that maximum pressure buildup in typical Mound Facility waste packages can be expected to be <0.25 MPa

Evaluation of cement composites for tritiated water fixation, 1

International Nuclear Information System (INIS)

Amano, Hiroshi; Sakuma, Youichi; Okamoto, Tadashi; Utsunomiya, Toru; Moriya, Toshio; Shimbo, Takashi; Higuchi, Masanori.

1985-01-01

The integrity of a waste package of tritiated waste is one of the most important parameters in proceeding safety assessments of tritiated waste disposal systems. Of the many terms governing the integrity of a waste package, the one that is directly connected with safety assessment is the leach rate of tritium from the solidified object. Experiments focusing on measurements of leach rates were therefore conducted. These experiments consisted of three stages, in the first stage experiment, types of cement and mix proportions were selected on the bases of (1) weight reduction, (2) micro-structure, (3) compressive strength, (4) ignition loss, and (5) chemical analysis. And two mix proportions each, for normal portland cement and special cement, were chosen for further testing. In the second stage, as a preliminary experiment for measuring the leach rate of tritium, the leach rate of deuterium was studied by measuring densities of immersed liquid. The examination of the relations between the leach rates and the beforementioned properties ((1) to (4) in the first stage experiment) clearly showed that the lower leach rate were achieved with the lower water-cement ratio which represented the higher density of the cement form. In the third stage experiment, it is planned hereafter to confirm the above results by carrying out leach tests for tritium. (author)

Induction of specific-locus mutations in the mouse by tritiated water

International Nuclear Information System (INIS)

Russell, W.L.; Cumming, R.B.; Kelly, E.M.; Phipps, E.L.

1978-01-01

The results reported are the first obtained on transmtted gene mutations induced by tritium in any form in any mammal. They are, therefore, of obvious practical importance in the estimaton of the possible biological hazards of man-made tritium in the environment. Male mice were injected intraperitoneally with either 0.75 or 0.50 mCi per gram of body weight of tritiated water. They were then used in our standard specific-locus mutation test in which the treated wild-type stock of mice is mated to a stock homozygous for seven recessive marker genes. Mutations at any of the seven loci are scored in the offspring. The earlier matings provided information on the mutation frequency in germ cells irradiated in postspermatogonial stages, and the later matings gave the mutation frequency in treated spermatogonia. The spermatogonia are the important cells so far as human risks are concerned, and the mouse results for this germ-cell stage yielded a relative biological effectiveness (RBE) of approximately 2 for tritiated water compared with low-dose-rate gamma irradiation. There are various uncertainties involved in arriving at this figure, and the difference between it and l is probably not statistically significant. However, for risk estimation, it seems prudent to use the RBE value of 2, which is, after all, the best point estimate computed from the present data

Some effects of irradiation of mice in utero with tritiated compounds

Energy Technology Data Exchange (ETDEWEB)

Lambert, B E; Phipps, M L [Radiobiology Department, The Medical College of Bartholomew' s Hospital, London, UK

1978-01-01

Mice have been exposed continuously, in utero, to tritiated water (via the maternal drinking water) or to tritiated thymidine (infused continuously into the mother). In both cases the patterns of labeling and subsequent loss of tritium over an extended period have been studied. The technique of infusion in unrestrained mice and its application in the production of fully tritium-labeled offspring is described in some detail. These fully labeled mice are being used to study a number of early and late effects, in particular, gonad cell effects and carcinogenesis, following this form of internal irradiation. Some preliminary results are presented. Similar results produced by homogeneous irradiation from tritiated water are also reported.

Some effects of irradiation of mice in utero with tritiated compounds

International Nuclear Information System (INIS)

Lambert, B.E.; Phipps, M.L.

1978-01-01

Mice have been exposed continuously, in utero, to tritiated water (via the maternal drinking water) or to tritiated thymidine (infused continuously into the mother). In both cases the patterns of labeling and subsequent loss of tritium over an extended period have been studied. The technique of infusion in unrestrained mice and its application in the production of fully tritium-labeled offspring is described in some detail. These fully labeled mice are being used to study a number of early and late effects, in particular, gonad cell effects and carcinogenesis, following this form of internal irradiation. Some preliminary results are presented. Similar results produced by homogeneous irradiation from tritiated water are also reported. (Auth.)

Tritium gas and tritiated water vapour behaviour in the environment from releases into the atmosphere from fusion reactors

International Nuclear Information System (INIS)

Velarde, Marta; Perlado, Manuel

2001-01-01

The diffusion of tritium from fusion reactors follows different ways according to the present chemical form, tritium gas or tritiated water vapour. The atmospheric conditions, speed and direction of the wind, rain intensity or stability class, are key factors in the dry and wet deposition. The obtained results demonstrate that the wet deposition is critical for the incorporation of the tritiated water vapour to the natural biological chain. However, the dry deposition is the factor that influences in the tritium gas form. The conversion of HT into HTO in the soil is rapid (1-7 days), and 20% of HT deposited in the soil is reemitted to the atmosphere in the form HTO, while the rest incorporates into the biological cycle. The rain factor accelerates the incorporation of tritium to the ground, the superficial waters and the underground waters

Using residual tritiated water from Cernavoda NPP to study Danube - Black Sea Canal hydrodynamics

International Nuclear Information System (INIS)

Varlam, C.; Stefanescu, I.; Lazar, R.; Varlam, M.; Patrascu, V.; Bucur, C.; Bobric, E.

2003-01-01

By benefiting of Cernavoda NPP's location in the neighbourhood of Danube - Black Sea Canal one suggests extending the area of interest along this canal particularly to use the residual tritiated water from this CANDU type reactor as tracing means in the study of canal's hydrodynamics. This canal appears to be ideal for such a study because releases in normal operation of NPP are occasional. The tritiated water can be used for simulating the transport and dispersion of soluble pollutants because it has the same physical characteristics as the usual water. By measuring response curves produced at injecting a known amount of tracer one can developed an efficient method for estimating: the soluble pollutant velocity along the canal; attenuation rate of concentration peak as a function of time as well as the time required by the propagation front of the soluble pollutant to reach a given point along the canal. In this work the calculation of the mixture length as a function of the particular characteristics of the canal is presented as well as different experimental formulas. Also the reference level of tritium concentration in the investigated area is established for future experiments

Investigation on degradation mechanism of ion exchange membrane immersed in highly concentrated tritiated water under the Broader Approach Activities

Energy Technology Data Exchange (ETDEWEB)

Iwai, Yasunori, E-mail: iwai.yasunori@jaea.go.jp; Sato, Katsumi; Yamanishi, Toshihiko

2014-10-15

Highlights: • Endurance of Nafion ion exchange membrane immersed into 1.38 × 10{sup 12} Bq/kg of highly concentrated tritiated water has been demonstrated. • The formation of free hydrophobic free products by reactions between radicals on the membrane and oxygen caused the decrease in ionic conductivity. • From the {sup 19}F NMR spectrum, no distinctive degradation in the membrane structure by interaction with tritium was measured. - Abstract: The ion exchange membrane is a key material for electrolysis cells of the water detritiation system. Durability of ion exchange membrane has been demonstrated under the Broader Approach Activities. Long-term exposure of Nafion{sup ®} ion exchange membrane in 1.38 × 10{sup 12} Bq/kg of tritiated water was conducted at room temperature for up to 2 years. The ionic conductivity of Nafion{sup ®} membrane after immersed in tritiated water was changed. The change in color of membrane from colorless to yellowish was caused by reactions of radicals on the polymer and oxygen molecules in air. Infrared Fourier transform spectrum of a yellowish membrane revealed a small peak for bending vibration of C-H situated at 1437 cm{sup −1}, demonstrating the formation of hydrophobic functional group in the membrane. The hydrophilic network in Nafion{sup ®} membrane was partially obstructed by the hydrophobic free products. This caused the decrease in ionic conductivity. The peak for bending vibration was clearly eliminated in the spectrum of the membrane after treatment by acid for removal of free products. The high-resolution solid state {sup 19}F NMR spectrum of a membrane after immersed in tritiated water was similar to that of a membrane irradiated with gamma-rays. From the {sup 19}F NMR spectrum, no distinctive degradation in the membrane structure by interaction with tritium was measured.

Investigation on degradation mechanism of ion exchange membrane immersed in highly concentrated tritiated water under the Broader Approach Activities

International Nuclear Information System (INIS)

Iwai, Yasunori; Sato, Katsumi; Yamanishi, Toshihiko

2014-01-01

Highlights: • Endurance of Nafion ion exchange membrane immersed into 1.38 × 10 12 Bq/kg of highly concentrated tritiated water has been demonstrated. • The formation of free hydrophobic free products by reactions between radicals on the membrane and oxygen caused the decrease in ionic conductivity. • From the 19 F NMR spectrum, no distinctive degradation in the membrane structure by interaction with tritium was measured. - Abstract: The ion exchange membrane is a key material for electrolysis cells of the water detritiation system. Durability of ion exchange membrane has been demonstrated under the Broader Approach Activities. Long-term exposure of Nafion ® ion exchange membrane in 1.38 × 10 12 Bq/kg of tritiated water was conducted at room temperature for up to 2 years. The ionic conductivity of Nafion ® membrane after immersed in tritiated water was changed. The change in color of membrane from colorless to yellowish was caused by reactions of radicals on the polymer and oxygen molecules in air. Infrared Fourier transform spectrum of a yellowish membrane revealed a small peak for bending vibration of C-H situated at 1437 cm −1 , demonstrating the formation of hydrophobic functional group in the membrane. The hydrophilic network in Nafion ® membrane was partially obstructed by the hydrophobic free products. This caused the decrease in ionic conductivity. The peak for bending vibration was clearly eliminated in the spectrum of the membrane after treatment by acid for removal of free products. The high-resolution solid state 19 F NMR spectrum of a membrane after immersed in tritiated water was similar to that of a membrane irradiated with gamma-rays. From the 19 F NMR spectrum, no distinctive degradation in the membrane structure by interaction with tritium was measured

Laboratory studies conducted for the development of a plant to concentrate the radioactive waste from tritiated water

International Nuclear Information System (INIS)

Bornea, Anisia; Zamfirache, Marius; Stefanescu, Ioan; Vasut, Felicia; Soare, Amalia

2010-01-01

The Cernavoda Nuclear Power Plant is the biggest operational source of tritium, in Europe and one of the most important in the world. The recovery of tritium from the moderator of operating Candu reactors and from the reactors to operate, represents a good opportunity for Romania to be involved in international collaboration programs in the field of nuclear fusion. Our interest is especially focussed on tritiated waste water with low activity resulted from the maintenance work performed on reactors with the purpose of reducing their volume and their reprocessing. The system presented in this work is based on the catalytic isotopic exchange and molecular dissociation CECE (Combined Electrolysis Catalytic Exchange). It has been noticed a growing interest regarding the electrolysers having polymer membranes as electrolyte SPM (solid polymer membrane). The advantage of using polymer membranes consists in the fact that membranes are actually the electrolyte and performs in the same time hydrogen and its isotopes separation. The present paper presents a conceptual design scheme for a tritium concentration system resulted from the tritiated waste water. This conceptual design represented the basis for the development of the installation for the tritiated waste water concentration, and the experiments to be performed will represent a support for promoting this technology. For designing the system and for analysing its functionality, a theoretical model for calculating tritium separation and concentration, has been developed.

Disposal of tritiated effluents

International Nuclear Information System (INIS)

Hartmann, K.; Bruecher, H.

1981-06-01

After some introductory remarks on the origin of tritium, its properties and its behaviour in a reprocessing plant three alternative methods for the disposal of tritiated effluents produced during reprocessing are described (deep well injection, in-situ solidification, deep-sea dumping) and compared with each other under various aspects. The study is based on the concept of a 1400 t/a reprocessing plant for LWR fuel, which annually produces 3000 m 3 of tritiated waste water with a tritium content of 6.5 x 10 12 Bq/m 3 as well as a residual fission product and actinide content. An assessment of the three methods under the aspects of simplicity, reliability, safety, costs, state of development and materials handling revealed advantages in favour of 'injection', followed by 'dumping' and 'in-situ solidification'. (orig./HP) [de

Tritium cycling in a tree spiked with tritiated water

International Nuclear Information System (INIS)

Murphy, C.E. Jr.; Luvall, J.C.

1979-01-01

Transfer and turnover rates in forests are important to compute the residence time of tritiated water in an area following an accidental release. In this study tritium was injected in the base of 7 year old, loblolly pine (Pinus taeda, L) trees to determine the rate of transfer through the trees and the turnover in the trees independent of the soil. The results indicate the flow rates depend on the rate of water movement through the tree, which is influenced by the microclimate, and exchange of tritium with hydrogen exchange sites in the tree. The initial pulse of tritium appears to move through the tree in about four days. The descending portion of the curve can be described as a two compartment model with half-lives of 1.41 and 21.7 days. There is some evidence that a longer turnover compartment is associated with metabolically fixed tritium

Pharmacokinetics of tritiated water in normal and dietary-induced obese rats

International Nuclear Information System (INIS)

Shum, L.Y.; Jusko, W.J.

1986-01-01

Tritiated water disposition was characterized in normal and dietary-induced obese rats to assess pharmacokinetic concerns in calculating water space and estimating body fat. A monoexponential decline in serum tritium activity was observed in both groups of rats, thus facilitating use of various computational methods. The volume of distribution and the total clearance of tritium in obese rats were larger than in normal rats because of the increased body weight. The values of water space (volume of distribution) estimated from moment analysis or dose divided by serum tritium activity at time zero (extrapolated) or at 2 hr were all similar. Thus, obesity does not alter the distribution equilibrium time and distribution pattern of tritium, and the conventional 2-hr single blood sampling after intravenous injection is adequate to estimate the water space of normal and obese rats

Sampling tritiated water vapor from the atmosphere by an active system using silica gel

Energy Technology Data Exchange (ETDEWEB)

Herranz, M. [Department of Nuclear Engineering and Fluid Mechanics, E.T.S.I. de Bilbao, University of the Basque Country (UPV/EHU), Alameda de Urquijo, s/n 48013 Bilbao (Spain); Alegria, N., E-mail: natalia.alegria@ehu.es [Department of Nuclear Engineering and Fluid Mechanics, E.T.S.I. de Bilbao, University of the Basque Country (UPV/EHU), Alameda de Urquijo, s/n 48013 Bilbao (Spain); Idoeta, R.; Legarda, F. [Department of Nuclear Engineering and Fluid Mechanics, E.T.S.I. de Bilbao, University of the Basque Country (UPV/EHU), Alameda de Urquijo, s/n 48013 Bilbao (Spain)

2011-11-15

Among the different methods used to collect the tritiated water vapor (HTO) contained in the atmosphere, one of the most worldwide used is its collection using an air pump, which forces the air to pass through a dry silica gel trap. The silica gel is then distilled to remove the water collected, which is measured in a liquid scintillation counting system. In this paper, an analysis of the water collection efficiency of the silica gel has been done as a function of the temperatures involved, the dimensions of the pipe driving the air into the silica gel traps, the air volume passing through the trap and the flow rates used. Among the obtained conclusions, it can be pointed out that placing the traps inside a cooled container, the amount of silica gel needed to collect all the water contained in the air passing through these traps can be estimated using a weather forecast and a psychometric chart. To do this, and as thermal equilibrium between incoming and open air should be established, a suitable design of the sampling system is proposed. - Highlights: > To recollect the atmosphere air tritiated water vapor, an active system was used. > The system is an air pump and three traps with silica gel connected by a rubber pipe. > The silica gel retention depends on the meteorological conditions and the flow rate. > The amount of water collected and the mass of silica gel need were calculated, F.

Preparation of tritiated tunicamycin

International Nuclear Information System (INIS)

Hunnicutt, R.E.; Keenan, R.W.

1986-01-01

A relatively simple and inexpensive procedure was devised for the radiolabeling of the glycoprotein biosynthesis inhibitor, tunicamycin. The procedure is based on hydrogen exchange in alkaline solutions of tritiated water. It was noted that the antibiotic was much more alkali labile than model compounds such as uridine. The alkali stability of the inhibitor was studied to determine conditions for optimum labeling and yield. The effects of alkaline incubation on the inhibitory properties of the antibiotic were also investigated and it was found that the breakdown products are not effective inhibitors of the reaction that transfers N-acetylglucosamine-1-phosphate to dolichyl phosphate. The isolated radioactive tunicamycin homologs, however, retained all their inhibitory action. Incubation of tunicamycin in the presence of deuterated water and mass spectral analysis showed that under the conditions used for the tritiation of tunicamycin the major product exchanged six hydrogen atoms. The position of the tritium atoms in labeled tunicamycin was not determined. The radioactive label in these compounds was shown to be stable under physiological conditions and should be useful for investigations involving the action of these antibiotics

Tritiated hydrogen conversion on heated metallic surfaces

International Nuclear Information System (INIS)

Ionita, G.; Mihaila, V.; Purghel, L.; Rebigan, F.

1995-01-01

This work reports investigations on tritiated hydrogen conversion to tritiated water on heated metallic surfaces. The HT conversion process has been revealed for copper, aluminium and stainless steel W4541 surfaces in the temperature range 150 to 300 o C, in case of the static regime and in the range 250 to 400 o C for the dynamic case. The most significant catalytic activity was shown by the copper sample. Studies on this subject are used as input information for different nuclear accident scenarios implying tritium leakage

Surface Water Modeling Using an EPA Computer Code for Tritiated Waste Water Discharge from the heavy Water Facility

International Nuclear Information System (INIS)

Chen, K.F.

1998-06-01

Tritium releases from the D-Area Heavy Water Facilities to the Savannah River have been analyzed. The U.S. EPA WASP5 computer code was used to simulate surface water transport for tritium releases from the D-Area Drum Wash, Rework, and DW facilities. The WASP5 model was qualified with the 1993 tritium measurements at U.S. Highway 301. At the maximum tritiated waste water concentrations, the calculated tritium concentration in the Savannah River at U.S. Highway 301 due to concurrent releases from D-Area Heavy Water Facilities varies from 5.9 to 18.0 pCi/ml as a function of the operation conditions of these facilities. The calculated concentration becomes the lowest when the batch releases method for the Drum Wash Waste Tanks is adopted

Tritium β-radiation induction of chromosomal damage: a calibration curve for low dose, low dose rate exposures of human cells to tritiated water

International Nuclear Information System (INIS)

Morrison, D.P.; Gale, K.L.; Lucas, J.N.

1997-01-01

Radiation exposures from tritium contribute to the occupational radiation exposures associated with CANDU reactors. Tritiated water is of particular interest since it is readily taken up by human cells and its elimination from the body, and, consequently, the radiation exposure of the cells, is spread over a period of days. Occupational exposures to tritiated water result in what are effectively chronic β-radiation exposures. The doses and dose rates ordinarily used in the definition of cellular responses to radiation in vitro, for use in biological dosimetry (the assessment of radiation exposures based on the observed levels of changes in the cells of exposed individuals), are usually much higher than for most occupational exposures and involve radiations other than tritium β-rays. As a result, their use in assessing the effects from tritiated water exposures may not be appropriate. We describe here an in vitro calibration curve for chronic tritium β-radiation induction of reciprocal chromosomal translocations in humn peripheral blood lymphocytes (PBLs) for use in biodosimetry. (author)

Atomic Energy of Canada Limited monitoring tritiated water in air and water effluents

International Nuclear Information System (INIS)

Osborne, R.V.; Tepley, N.W

1978-01-01

Current on-line methods of monitoring effluents for tritium (as tritiated water, HTO) measure concentrations in air above 250 nCi/m 3 (approx. 10 kBq/m 3 ) and in water above 1 uCi/kg (approx. 40 kBq/kg). Some of the problems encountered in such monitoring are the presence of fission and activation products in the effluents and, particularly in water monitoring, the often dirty quality of the sample. In a new design of monitor, HTO is collected directly from air by a flow of liquid scintillator (LS). For water monitoring a flow of air continuously samples the water and transports HTO to the LS. The key features of the new design are that the high detection efficiency of LS is realizable, that the rate of use of LS is only approx. 2 mm 3 /s, that the controlled evaporation and metering of air provides the low flow of HTO needed for mixing with LS, and that accurate metering of a dirty effluent is not needed. The sensitivities for detecing tritium on-line are improved by at least an order of magnitude

Body composition and water metabolism in tropical ruminants using tritiated water

International Nuclear Information System (INIS)

Ranjhan, S.K.; Kalanidhi, A.P.; Gosh, T.K.; Singh, U.B.; Saxena, K.K.

1982-01-01

Experiment 1. Studies were conducted on Muzaffarnagri, Muzaffarnagri x Dorset and Muzaffarnagri x Suffolk breeds of sheep to determine the water turnover rates and body composition. The native Muzaffarnagri and crossbred animals did not differ significantly in body composition. The water turnover rates were not significantly different between breeds within the same season, but a significant difference was observed between the two seasons (winter and summer). Experiment 2. Nine animals, three each of crossbred cattle (Hariana x Holstein), buffalo and crossbred sheep (Muzaffarnagri x Suffolk), were used to determine the body composition by the indirect method in the two seasons. There was a reduction in the TOH space and total body water during the summer season in cattle and buffalo as compared with the winter season. Experiment 3. Four adult Barbari goats were used to study body composition by direct (slaughter) and indirect (isotope dilution) techniques. There was a significant correlation between corrected TOH space and total body water, fat and protein. Experiment 4. Twelve animals, three each of buffalo, crossbred cattle (Hariana x Holstein), crossbred sheep (Muzaffarnagri x Suffolk) and Barbari goats, were used to determine the water requirements during the two seasons (winter and summer) by the tritiated water (TOH) dilution technique. There were significant differences (P < 0.01) in the water requirement and water turnover between seasons and between species within a season. The lowest water turnover and water requirement were found in goats, followed by sheep, crossbred cattle and buffalo when expressed as ml/kgsup(0.82).d. The metabolic water production was 10% of the total water input in the case of buffalo and crossbred cattle, but it was more in sheep and goats in both seasons

Gas and Water Permeability of Concrete

Energy Technology Data Exchange (ETDEWEB)

Villar, M. V.; Martin, P. L.; Romero, F. J.; Gutierrez-Rodirgo, V.; Barcala, J. M.

2012-11-01

The gas pressure of concrete samples was measured in an unsteady-state equipment working under low injection pressures and in a newly fine tuned steady-state setup working under different pressures. These measurements allowed the estimation of the intrinsic and relative gas permeability of the concrete and of the effect of boundary conditions on them. Permeability decreased with water content, but it was also greatly affected by the hydraulic history of concrete, i.e. if it had been previously dried or wetted. In particular, and for a given degree of saturation, the gas permeability of concrete previously saturated was lower than if the concrete had been just air dried or saturated after air drying. In any case, the gas permeability was about two orders of magnitude higher than the liquid water permeability (10-16 vs. 10-18 m2), probably due to the chemical reactions taking place during saturation (carbonation). The relative gas permeability of concrete increased sharply for water degrees of saturation smaller than 50%. The boundary conditions also affected the gas permeability, which seemed to be mostly conditioned by the back pressure and the confining pressure, increasing as the former increased and decreasing as the latter increased, i.e. decreasing as the effective pressure increased. Overall the increase of pressure head or injection pressure implied a decrease in gas permeability. External,microcracking during air-drying could not be ruled out as responsible for the decrease of permeability with confining pressure. The apparent permeability obtained applying the Klinkenberg method for a given effective pressure was only slightly smaller than the average of all the values measured for the same confining pressure range. For this reason it is considered that the Klinkenberg effect was not relevant in the range of pressures applied. (Author) 37 refs.

Bioaccumulation of tritiated water in phytoplankton and trophic transfer of organically bound tritium to the blue mussel, Mytilus edulis.

Science.gov (United States)

Jaeschke, Benedict C; Bradshaw, Clare

2013-01-01

Large releases of tritium are currently permitted in coastal areas due to assumptions that it rapidly disperses in the water and has a low toxicity due to its low energy emissions. This paper presents a laboratory experiment developed to identify previously untested scenarios where tritium may concentrate or transfer in biota relevant to Baltic coastal communities. Phytoplankton populations of Dunaliella tertiolecta and Nodularia spumigena were exposed at different growth-stages, to tritiated water (HTO; 10 MBq l(-1)). Tritiated D. tertiolecta was then fed to mussels, Mytilus edulis, regularly over a period of three weeks. Activity concentrations of phytoplankton and various tissues from the mussel were determined. Both phytoplankton species transformed HTO into organically-bound tritium (OBT) in their tissues. D. tertiolecta accumulated significantly more tritium when allowed to grow exponentially in HTO than if it had already reached the stationary growth phase; both treatments accumulated significantly more than the corresponding treatments of N. spumigena. No effect of growth phase on bioaccumulation of tritium was detectable in N. spumigena following exposure. After mussels were given 3 feeds of tritiated D. tertiolecta, significant levels of tritium were detected in the tissues. Incorporation into most mussel tissues appeared to follow a linear relationship with number of tritiated phytoplankton feeds with no equilibrium, highlighting the potential for biomagnification. Different rates of incorporation in species from a similar functional group highlight the difficulties in using a 'representative' species for modelling the transfer and impact of tritium. Accumulations of organic tritium into the mussel tissues from tritiated-phytoplankton demonstrate an environmentally relevant transfer pathway of tritium even when water-concentrations are reduced, adding weight to the assertion that organically bound tritium acts as a persistent organic pollutant. The

Formation of volatile decomposition products by self-radiolysis of tritiated thymidine

International Nuclear Information System (INIS)

Shiba, Kazuhiro; Mori, Hirofumi

1997-01-01

In order to estimate the internal exposure dose in an experiment using tritiated thymidine, the rate of volatile 3 H-decomposition of several tritiated thymidine samples was measured. The decomposition rate of (methyl- 3 H)thymidine in water was over 80% in less than one year after initial analysis. (methyl- 3 H)thymidine was decomposed into volatile and non-volatile 3 H-decomposition products. The ratio of volatile 3 H-decomposition products increased with increasing the rate of the decomposition of (methyl- 3 H) thymidine. The volatile 3 H-decomposition products consisted of two components, of which the main component was tritiated water. Internal exposure dose caused by the inhalation of such volatile 3 H-decomposition products of (methyl- 3 H) thymidine was assumed to be several μSv. (author)

Evaluation of neonatal squirrel monkeys receiving tritiated water throughout gestation

International Nuclear Information System (INIS)

Jones, D.C.L.; Krebs, J.S.; Sasmore, D.P.; Mitoma, C.

1980-01-01

Pregnant squirrel monkeys received tritiated water (HTO) in the drinking water throughout gestation at levels ranging from 16 to 1000 times the permissible level for human consumption (0.003 μCi/ml), resulting in mean body water HTO levels ranging from 0.05 to 3.1 μCi/ml. There were no discernible effects of HTO administration on the newborn progeny in terms of body weight, body dimensions, selected organ weights (brain, heart, adrenal, kidney, liver, spleen), hematologic patterns, and histology of selected organs and tissues (adrenal, kidney, liver, lung, brain, pancreas, jejunum, pituitary, spleen, testes, thymus, skin) other than ovaries. The number of primary oocytes in female progeny decreased markedly with increasing levels of HTO in maternal drinking water. Quantitative analysis of neonate ovaries, testes, brain tissue, and retinal tissue is in progress. No effects of HTO administration on maternal body weight, gestation time, or maintenance of pregnancy to full term were observed. Body weights of HTO-treated inseminated females that did not deliver were less than control weights, but the lack of dose dependence implies that this effect may have been associated with a stimulus characteristic of the HTO administration rather than with irradiation

Sorption of tritium and tritiated water on construction materials

International Nuclear Information System (INIS)

Dickson, R.S.; Miller, J.M.

1991-11-01

Sorption and desorption of tritium (HT) and tritiated water (HTO) on materials to be used in the construction of fusion facilities were studied. In ∼ 24-hour exposures in argon or room air, metal samples sorbed 8-200 μCi/m 2 of tritium from atmospheres of 5-9 Ci/m 3 HT, and non-metallic samples sorbed 60-800 μCi/m 2 from atmospheres of 14 Ci/m 3 HT. Sorption of HTO varied much more widely than HT sorption for different samples, ranging from 4 μCi/m 2 for glass to 1,300,000 μCi/m 2 for concrete samples, in 24-hour exposures to 1 Ci/m 3 HTO in room air. Time dependence of desorption in dry air showed a rapid initial process and a slower secondary process. (Author) (10 refs., 4 figs., 2 tabs.)

Immobilization of tritiated waste-water by hydraulic cements. A survey of the state-of-the-art

International Nuclear Information System (INIS)

Mannone, F.

1987-01-01

An experimental research programme including as one of its major items the definition of a strategy for tritiated waste management is being prepared at the JRC-Ispra. Laboratory work will be performed in ETHEL, the European Tritium Handling Experimental Laboratory under construction at Ispra. To provide background information needed for defining items and planning the execution of such activities, a survey of the state of the art and R and D performed in the field of tritiated water immobilization by hydraulic cements and ultimate packaging by multiple containment systems has been carried out. Particular attention has been focused on results of tritium leach test programmes performed at various USA laboratories in order to verify the leach resistance properties of some tritium immobilization and containment options. Problems and draw backs associated with such options are discussed. Final conclusions are presented. 49 refs

The distribution of tritium among the amino acids of proteins obtained from mice exposed to tritiated water

International Nuclear Information System (INIS)

Commerford, S.L.; Carsten, A.L.; Cronkite, E.P.

1983-01-01

The distribution of tritium among the amino acids of serum proteins in mice chronically exposed to tritiated water was determined by ion exchange chromatography of the protein hydrolysate. The specific activity of nonexchangeable tritium in these amino acids relative to the specific activity of tritium in the tissue water of mice ranged from 0.04 for phenylalanine and threonine to 1.0 for glycine and alanine. Since tritium from tissue water can enter the nonexchangeable positions of amino acids only as the result of metabolic processing, the relative specific activity of tritium in each amino acid is an indicator of the extent of such processing. The tritium content of tyrosine and all the amino acids required in the diet for survival is quite low, except for histidine, and can be entirely accounted for by transamination or, in the case of methionine, by transmethylation. The tritium content of the other amino acids is too high to result from such minor processing and must reflect primarily the fraction synthesized de novo. The implications of these findings with respect to the radiobiological consequences of a diet containing tritiated proteins are discussed

Embryonic/fetal mortality after exposure to tritiated water in pregnant Swiss albino mice during different gestation periods

International Nuclear Information System (INIS)

Sharma, Kalpana; Saini, M.R.

1993-01-01

Pregnant Swiss albino mice were given a priming injection(im) of tritiated water (HTO) at the dose rate of 2.3 and 5 μCi/ml body water (74, III or 185 K Bq/ml body water) at 0,6 and 14 day post conception (d.p.c) and were subsequently maintained on tritiated drinking water ad libitum during preimplantation (0-5 d.p.c), organogenetic (6-12 d.c.p.) or fetal (14-18 d.p.c) period, respectively. On day 18 of gestation the females were sacrificed by cervical dislocation to record the implant sites per dam and embryonic/fetal mortality. Significant reduction was observed in average implant sites per dam when the females were exposed to any of the three doses during the preimplantation period due to embryonic resorption before implantation. However, the same was found to be within the normal range when mothers were exposed during the organogenetic or fetal period. Prenatal mortality (embryonic resorption/fetal death) was higher after in utero exposure to different doses during preimplantation period as compared to organogenetic period, but mortality did not occur after exposure to any of the doses during the fetal period. Occurrence of mortality was found to be dose dependent. (author). 25 refs., 1 tab

Detritiation of Tritiated Effluent Gas and Water

International Nuclear Information System (INIS)

Ahn, Do Hee; Kim, Kwang Rag; Paek, Seung Woo; Lee, Min Soo; Yim, Sung Paal; Chung Hong Suk

2007-06-01

In a demonstration scale equipment for treatment of tritium in off-gas, Pt/SDBC as oxidation catalyst and Zeolite 13X as adsorbent was charged in the beds, respectively. It was confirmed from the performance test that decontamination factor of the equipment showed more than 100 under the flow rate of off-gas of 90 l/hr and at the temperature of 65 ∼ 80 .deg. C. A small scale CECE process has been developed combining LPCE catalytic column with SPE (solid polymer electrolyte) electrolysis. The catalytic column was a trickle-bed type packed with the mixture of 1 wt% Pt/SDBC catalyst and 4 mm Dixon wire-mesh ring. The experimental results of the CECE process proved that the decontamination factor of 13 ∼ 20 under the operating conditions of the water of the 4 l/day and the effluent hydrogen gas of 16.2 mol/h. A design code of CECE process also developed which will be applied the tritium industry. An experimental method for the reduction of tritiated organic waste by using catalytic oxidation was tested in a heated catalytic reactor of 0.5 wt% Pd/Al 2 O 3 . The simulated organic liquid was converted to water over 99%. A gas chromatographic column material was developed for the separation of mixed hydrogen isotopes. 17 wt% Pd-Pt on alumina showed 90% separation efficiency at 77 % yield for the separation of 29.2 % D 2 -H 2 gas mixture

Detritiation of Tritiated Effluent Gas and Water

Energy Technology Data Exchange (ETDEWEB)

Ahn, Do Hee; Kim, Kwang Rag; Paek, Seung Woo; Lee, Min Soo; Yim, Sung Paal; Chung Hong Suk

2007-06-15

In a demonstration scale equipment for treatment of tritium in off-gas, Pt/SDBC as oxidation catalyst and Zeolite 13X as adsorbent was charged in the beds, respectively. It was confirmed from the performance test that decontamination factor of the equipment showed more than 100 under the flow rate of off-gas of 90 l/hr and at the temperature of 65 {approx} 80 .deg. C. A small scale CECE process has been developed combining LPCE catalytic column with SPE (solid polymer electrolyte) electrolysis. The catalytic column was a trickle-bed type packed with the mixture of 1 wt% Pt/SDBC catalyst and 4 mm Dixon wire-mesh ring. The experimental results of the CECE process proved that the decontamination factor of 13 {approx} 20 under the operating conditions of the water of the 4 l/day and the effluent hydrogen gas of 16.2 mol/h. A design code of CECE process also developed which will be applied the tritium industry. An experimental method for the reduction of tritiated organic waste by using catalytic oxidation was tested in a heated catalytic reactor of 0.5 wt% Pd/Al{sub 2}O{sub 3}. The simulated organic liquid was converted to water over 99%. A gas chromatographic column material was developed for the separation of mixed hydrogen isotopes. 17 wt% Pd-Pt on alumina showed 90% separation efficiency at 77 % yield for the separation of 29.2 % D{sub 2}-H{sub 2} gas mixture.

Steam-water relative permeability

Energy Technology Data Exchange (ETDEWEB)

Ambusso, W.; Satik, C.; Home, R.N. [Stanford Univ., CA (United States)

1997-12-31

A set of relative permeability relations for simultaneous flow of steam and water in porous media have been measured in steady state experiments conducted under the conditions that eliminate most errors associated with saturation and pressure measurements. These relations show that the relative permeabilities for steam-water flow in porous media vary approximately linearly with saturation. This departure from the nitrogen/water behavior indicates that there are fundamental differences between steam/water and nitrogen/water flows. The saturations in these experiments were measured by using a high resolution X-ray computer tomography (CT) scanner. In addition the pressure gradients were obtained from the measurements of liquid phase pressure over the portions with flat saturation profiles. These two aspects constitute a major improvement in the experimental method compared to those used in the past. Comparison of the saturation profiles measured by the X-ray CT scanner during the experiments shows a good agreement with those predicted by numerical simulations. To obtain results that are applicable to general flow of steam and water in porous media similar experiments will be conducted at higher temperature and with porous rocks of different wetting characteristics and porosity distribution.

Tritiated ammonia formation

International Nuclear Information System (INIS)

Heung, L.K.

1995-01-01

When nitrogen was selected as the glovebox atmosphere for the Replacement Tritium Facility (RTF) at the Savannah River Site (SRS), a concern was raised as to the possibility of tritiated ammonia formation in the gloveboxes. Experimental data were produced to study the tritiated ammonia formation rate in a tritium and nitrogen mixture. A rate equation that closely simulates the experimental data was developed. This rate equation can be used to calculate the formation of tritiated ammonia from different concentrations of tritium and nitrogen. The reaction of T 2 and N 2 to form NT 3 is a slow process, particularly when the tritium concentration is low. The reaction requires weeks or months to reach radiochemical equilibrium dependent on the concentrations of the reactants. 4 refs., 6 figs., 1 tab

Differential effects of chronic ingestion of tritiated water on prenatal brain development

International Nuclear Information System (INIS)

Zamenhof, S.

1990-01-01

Female rats were given tritiated drinking water (3 microCi/ml) from 30 days before mating up to and throughout pregnancy. At this low dose, the course and the outcome of pregnancy were normal. The differences between newborn body and cerebral weights of the treated rats and those of control animals were on the borderline of significance. In contrast, cerebral DNA and cerebral protein were highly significantly lower. In 30-35% of the treated population the DNA and protein values were more than 2 standard deviations (SD) below the mean values for the control population. Thus the number of the progeny of the mothers exposed to tritiated water that were considered to have outstandingly low levels of DNA and protein was 14-17 times greater than in the control group. The irradiated population also had 3-5% of severely affected individuals with cerebral DNA and protein values more than 2 SD below the mean of the experimental population. However, even in this irradiated population, a certain number of individuals did not show the effects of radiation as indicated by DNA and protein values that were not lower than the mean values of the control population. These animals may represent those individuals in which normal (control) populations would have cerebral DNA and protein levels well above the average (by 1 to 2 SD), but here, because of prenatal irradiation, were about average. If so, this lack of effect of irradiation cannot be caused by protection against radiation. However, at present, a differential repair mechanism of protection in those animals (or their mothers) that showed little or no effect of irradiation cannot be excluded

Incorporation and distribution of tritium in rats after chronic exposure to various tritiated compounds

International Nuclear Information System (INIS)

Takeda, H.

1991-01-01

Rats were chronically exposed to tritiated water ( 3 HHO) and several tritiated organic compounds ([ 3 H]leucine, [ 3 H]lysine, [ 3 H]glucose, [ 3 H]glucosamine, [ 3 H]thymidine and [ 3 H]uridine) dissolved in their drinking water. An analysis of tritium in wet and dry tissues of rats at the end of 22 days' chronic exposure showed that the chemical form of the ingested tritium was more important for tritium uptake in dry tissues than in wet tissues. The highest concentrations of OBT (organically bound tritium) were found in rats exposed to tritiated amino acids ([sup (3)/H]lysine and [ 3 H]leucine), 4-9 times higher than those in rats exposed to 3 HHO. The next highest concentrations were found in rats exposed to [ 3 H]uridine., The result of radiation dose estimations at the end of chronic exposure showed the contribution of OBT to total dose rate was higher in the tissues of rats exposed to tritiated organic compounds than that after exposure to 3 HHO. The differences between total dose rates from 3 HHO and those from tritiated organic compounds were within a factor of 2. (author)

The determination of effective doses from the intake of tritiated water

International Nuclear Information System (INIS)

1987-08-01

To comply with the regulatory requirements relating to the dose from exposures to tritiated water (HTO), Atomic Energy Control Board (AECB) licensees currently measure tritium concentration in urine to determine whole body dose. This approach has been based on the consideration that the time-integrated tritium concentration (which is proportional to accumulated dose) in any organ from urine concentrations are always conservative. The International Commission on Radiological Protection (ICRP) recommends that the average soft tissue dose be used to determine effective dose equivalents for HTO exposures. The ICRP also recommends that only the retention in body water be considered when committed doses from HTO exposures are calculated; this recommendation is based on the consideration that the errors introduced by neglecting the long-lived tritium component (those tritium atoms retained in organic molecules of the body cells) are small (only of the order of 10% of the committed dose equivalent to the whole body). The AECB position is presented in the following regulatory policy statement

Bioaccumulation of tritiated water in phytoplankton and trophic transfer of organically bound tritium to the blue mussel, Mytilus edulis

International Nuclear Information System (INIS)

Jaeschke, Benedict C.; Bradshaw, Clare

2013-01-01

Large releases of tritium are currently permitted in coastal areas due to assumptions that it rapidly disperses in the water and has a low toxicity due to its low energy emissions. This paper presents a laboratory experiment developed to identify previously untested scenarios where tritium may concentrate or transfer in biota relevant to Baltic coastal communities. Phytoplankton populations of Dunaliella tertiolecta and Nodularia spumigena were exposed at different growth-stages, to tritiated water (HTO; 10 MBq l −1 ). Tritiated D. tertiolecta was then fed to mussels, Mytilus edulis, regularly over a period of three weeks. Activity concentrations of phytoplankton and various tissues from the mussel were determined. Both phytoplankton species transformed HTO into organically-bound tritium (OBT) in their tissues. D. tertiolecta accumulated significantly more tritium when allowed to grow exponentially in HTO than if it had already reached the stationary growth phase; both treatments accumulated significantly more than the corresponding treatments of N. spumigena. No effect of growth phase on bioaccumulation of tritium was detectable in N. spumigena following exposure. After mussels were given 3 feeds of tritiated D. tertiolecta, significant levels of tritium were detected in the tissues. Incorporation into most mussel tissues appeared to follow a linear relationship with number of tritiated phytoplankton feeds with no equilibrium, highlighting the potential for biomagnification. Different rates of incorporation in species from a similar functional group highlight the difficulties in using a ‘representative’ species for modelling the transfer and impact of tritium. Accumulations of organic tritium into the mussel tissues from tritiated-phytoplankton demonstrate an environmentally relevant transfer pathway of tritium even when water-concentrations are reduced, adding weight to the assertion that organically bound tritium acts as a persistent organic pollutant. The

Utilization of tritiated water dilution technique in determination of nitrogen partitioning in cashmere goats

International Nuclear Information System (INIS)

Wang Linfeng; Yang Gaiqing; Liu Ping; Zhang Shijun

2010-01-01

In order to investigate nitrogen partitioning in local cashmere goats, six Inner Mogolia White Cashmere goats between 2 to 2.5 years old were used to determine the nitrogen partitioning in cashmere goats. The total retained nitrogen (TN) in body, distribution of body nitrgen and hair nitrogen were measured by general digestive and metabolism method combined with tritiated water dilution technique. Results showed that the combined methods were ideal for determining body nitrgen (BN) and hair nitrogen (fur nitrogen, FN) of Cashmere goats. There were obvious significance between BN and FN in different seasons. In telogen, BN and FN partitioning was 75.7% ± 0.62% and 24.3% ± 0.62%, respectively. Whereas, it changed to 66.6% ± 2.2% and 33.4% ± 2.2% in anagen. BN partitioning decreased when the season changed from telogen to anagen, while FN partitioning increased, which indicated that more nitrogen substance was partitioned to body growth in telogen, and more nitrogen substance was distribute to cashmere growth in anagen. These transformation were related to the changing of photoperiod and some hormones, such as melatonin (MT), prolactin (PRL) and IGF-I. It could be concluded that tritiated water dilution technique can be used to detect body protein content as well as BN, combining general digestive and metabolism experiment, FN partitoning can be determined. BN and FN partitoning varied with the season in cashmere goats because of hormones changing. (authors)

Urban evaporation rates for water-permeable pavements.

Science.gov (United States)

Starke, P; Göbel, P; Coldewey, W G

2010-01-01

In urban areas the natural water balance is disturbed. Infiltration and evaporation are reduced, resulting in a high surface runoff and a typical city climate, which can lead to floods and damages. Water-permeable pavements have a high infiltration rate that reduces surface runoff by increasing the groundwater recharge. The high water retention capacity of the street body of up to 51 l/m(2) and its connection via pores to the surface lead to higher evaporation rates than impermeable surfaces. A comparison of these two kinds of pavements shows a 16% increase in evaporation levels of water-permeable pavements. Furthermore, the evaporation from impermeable pavements is linked directly to rain events due to fast-drying surfaces. Water-permeable pavements show a more evenly distributed evaporation after a rain event. Cooling effects by evaporative heat loss can improve the city climate even several days after rain events. On a large scale use, uncomfortable weather like sultriness or dry heat can be prevented and the urban water balance can be attenuated towards the natural.

Evaluation of neonate squirrel monkeys receiving tritiated water throughout gestation

International Nuclear Information System (INIS)

Jones, D.C.L.

1978-01-01

The effect of receiving tritiated water (HTO) throughout gestation on the developing primate was assessed by administering HTO to adult female squirrel monkeys (Saimiri sciureus) as the only source of drinking water beginning with the day of insemination and continuing throughout pregnancy. For the control (tap water) and six experimental groups, the mean urinary tritium concentrations in females delivering full-term progeny were <0.004, 0.05, 0.16, 0.33, 0.75, 1.61, and 3.09 microcuries/ml. Positive bioassays for pregnancy were observed in about half of 277 inseminated females. Among pregnant females, the full-term delivery rate was 36%, the abortion rate was 7%, and the resorption rate was 58% with no discernible effect of HTO administration on any of these parameters. The 46 full-term progeny were evaluated within 2 days of birth. No effects of HTO administration were observed in terms of gestation period (median 153 days, range 141-158 days), sex distribution, body weight, body dimensions, selected organ weights, histology (except gonads), or hematologic pattern. The number of primary oocytes in female progeny decreased markedly within increasing concentrations of tritium. Specific quantification of this effect and evaluation of the neonate testes is in progress

Threshold dose to developing central nerve system of rats and mice from prenatal exposure to tritiated water

International Nuclear Information System (INIS)

Zhou Xiangyan; Wang Bing; Gao Weimin; Lu Huimin

1999-01-01

Objective: To study the threshold dose to the developing central nerve system of rats and mice from prenatal exposure to tritiated water. methods: Pregnant adult C 57 BL/6J strain mice and Wistar strain rats were irradiated with beta-rays from HTO by a single intraperitoneal injection on the 12.5 th and 13 th days of gestation. The activities of HTO were 24.09, 48.18 and 144.54 ( x 10 4 Bq/g bw), respectively. Fifty-six parameters including postnatal growth, neutro-behavior, pathology of brain, neuropeptide contents, changes of hippocampal neurons, Ca 2+ conductance of hippocampal neurons etc were used to test the teratogenic threshold dose the lowest dose was different from that of the control). Results: Of the observed 56 parameters of rats and mice 80.4% indicated that the threshold doses for prenatal HTO exposure ranged from 0.030 Gy to 0.092 Gy, and the other 19.6% showed the threshold doses from 0.093 to 0.300 Gy. Conclusions: There exists threshold dose from the low level tritiated water irradiation of the developing central nerve system

Conversion of tritiated hydrogen to tritiated water on heated metal surfaces

International Nuclear Information System (INIS)

Dickson, R.S.

1993-05-01

The conversion of tritium to tritiated water on metal surfaces was studied under conditions relevant to releases into a fusion reactor hall (metal temperatures between 473 K and 623 K, air or inert gas atmospheres). The rate constant of oxidation per unit geometric surface area was found to be about a factor of ten higher than the rate constant per unit gas adsorption surface area for H 2 to H 2 O conversion on metal oxides in excess oxygen, probably because of the roughness of the metal surfaces on a gas adsorption scale. Surface roughness and oxides were found to have a major influence on the reaction rate. The reaction exhibited a first-order dependence on Q 2 concentration. Changing the dew point of the atmosphere did not affect the rate significantly, and rate constants for most metals were independent of whether the atmosphere was argon or air. Coatings of hydrocarbon and silicone polymers did not significantly affect the reaction rate on carbon steel and ferrous metals and brass all had about the same conversion rate constant. Aluminum alloy gave about three times lower and copper in Ar gave ten times higher conversion rate constants. Based on these data, an accident scenario involving exposure of 1000 m 2 of stainless steel at 573 K to a 10 4 m 3 room would cause conversion of ca. 0.1% of the Q 2 present to Q 2 O in 24 hours, while air ingress to the torus without leakage of the tritium into the room would cause 1.2% conversion in that time. The rate values are only accurate within a multiplicative factor of three, so they should be applied cautiously in model calculations. (author). 27 refs., 4 tabs., 4 figs

Effect of lifetime intake of organically bound tritium and tritiated water on the oocytes of rats

International Nuclear Information System (INIS)

Pietrzak-Flis, Z.; Wasilewska-Gomulka, M.

1984-01-01

Rats were continuously exposed to constant activity of tritium in drinking water (HTO group) or to tritium organically bound in food (T-food group) in the period from conception of F 1 generation through maturity. Female offspring were killed at the age of 21 and 71 days and the oocytes in their ovaries were counted. Mean dose rates absorbed in the ovaries were for the HTO groups 7.25+-0.37 and 14.73+-0.79 mGy/day and for the T-food group 4.84+-0.25 mGy/day. Reduction in the oocyte number in the ovaries of females exposed to tritiated food was bigger than in the ovaries of females exposed to tritiated water. The dependence of the survival of small oocytes on the dose rate and the corresponding total accumulated dose had an exponential character. The damaging effect of tritium was for the period from conception to 21 days of age bigger than from 21 to 71 days of age. Of all stages of oocyte development, the highest sensitivity to tritium irradiation was observed in small oocytes and oocytes with one complete layer of follicle cells. As a result, relative number of the growing and large oocytes increased. (orig.)

Tritiated-water detection with a 2D(γ,n)1H monitor

International Nuclear Information System (INIS)

Winn, W.G.; Baumann, N.P.

Tritiated process water is monitored by detecting the D 2 O component via the 2 D(γ,n) 1 H reaction. A probe containing a 1 to 7 mCi 24 Na (15 h) γ-source and six 3 He neutron detectors produces and monitors the 2 D(γ,n) 1 H reaction. A variety of probe configurations were examined for D 2 O detection sensitivity. The corresponding detection limits range from 6 to 280 μL for D 2 O droplets and 1 to 13 μL/cm for D 2 O streams, when 10-minute neutron counting with a 1 mCi γ-source is used. Results from two field applications illustrate the utility of the monitor

Digestibility of cow's tritiated milk powder by calf and pig

International Nuclear Information System (INIS)

Bruwaene, R. van; Kirchmann, R.; Charles, P.; Hoek, J. van den

1976-01-01

Milk obtained from a lactating cow, maintained in a byre and fed on tritiated drinking water (266 μCi/1), was used in these experiments. Tritium moves into the different metabolic pathways that eventually produce milk. After administration of this continuous oral dose of tritiated water, the tritium content of the whole milk and of the dry matter reaches a plateau 10 days after the beginning of the ingestion of THO. Analysis of the radioactivity in the several milk constituents indicated that tritium was incorporated to different extents in different components. This in vivo tritiated milk powder was fed to two calves and three pigs in their rations. Daily samples of faeces were taken. For determining the digestibility and the incorporation of this milk powder the animals were slaughtered and several organs examined. The tritium activity was determined in the dry matter of the organs and the faeces. The data obtained in these experiments indicate that the milk powder is better absorbed by the calf if the digestibility coefficient is taken into consideration, but the milk powder is better incorporated in the organic matter of the muscle and liver of the pig. (author)

Excretion and intestinal absorption of tritiated glutamic acid by carp, Cyprinus Carpio

International Nuclear Information System (INIS)

Watabe, Terushia; Kistner, G.

1986-01-01

Excretion and intestinal absorption of tritiated glutamic acid by carp was investigated. Approximately 80% of orally administered tritium was excreted at a half life value of 1.4 h and an observed slower excretion of 7 days for the remainder. Tritium incorporated in glutamic acid was efficiently retained at the site of absorption, i.e. intestine, liver, gill, kidney, blood and muscle. A dual marking experiment using tritiated glutamic acid and 14 C-market glutamic acid showed higher excretion of tritium by factors 2.0 to 4.9 than that of 14 C. Tritiated glutamic acid is considered to be mainly incorporated in the citric acid cycle soon after administration and the release of tritium in tritiated water through the cycle is assumed as causing the initial rapid excretion of tritium in carp. The intestinal absorption of glutamic acid was likely to depend on its concentration in the administered solution. The maximum level of absorption is estimated to be 0.1 m mol/0.5 h for one year old carp. The results obtained here would make it possible to estimate the tritium contamination of fish due to tritiated glutamic acid entering the food chain. (orig.)

Dose contribution from metabolized organically bound tritium after acute tritiated water intakes in humans

International Nuclear Information System (INIS)

Trivedi, A.; Galeriu, D.; Richardson, R.B.

1997-01-01

Urine samples from eight male radiation workers who had an unplanned acute tritiated water intake were measured for tritium-in-urine up to 300 d post-exposure. During the first month or so post-exposure, these individuals increased their fluid intakes to accelerate the turnover rate of tritium in the body for dose mitigation. Their daily fluid intakes reverted to normal levels in the latter period of the study. A non-linear regressional analysis of the tritium-in-urine data showed that the average biological half-life of tritium in body water, with standard deviation, was 63 ± 1.0 d (range, 5.0-8.1 d) and 8.4 ± 2.0 d (range, 6.2-12.8 d) during the respective periods of increased fluid intake and the later period of normal fluid intake. A longer term component of tritium excretion was also observed with average biological half-life of 74 ± 18 d (range, 58-104 d), indicating the incorporation of tritium, and its retention, in the organic fractions of the body. A mathematical model was developed and used to estimate the dose increase from the metabolized organically bound tritium on the basis of the kinetics of tritium-in-urine. The model accounts for a change in the rates of urinary excretion caused by variable fluid intakes. The average dose to the body, for the eight male workers, due to the metabolized organically bound tritium was estimated to be 6.2 ± 1.3% (range, 3.5% to 8.9%) of the committed effective dose due to tritium in the body water. This value for the dose increase from organically bound tritium is in the range of the current recommendations of the International Commission on Radiological Protection, i.e., organically bound tritium incorporated into the body contributes about 10% of the dose to the body water following tritiated water intakes. (author)

Modelling of water permeability in cementitious materials

DEFF Research Database (Denmark)

Guang, Ye; Lura, Pietro; van Breugel, K.

2006-01-01

This paper presents a network model to predict the permeability of cement paste from a numerical simulation of its microstructure. Based on a linked list pore network structure, the effective hydraulic conductivity is estimated and the fluid flow is calculated according to the Hagen-Poiseuille law....... The pressure gradient at all nodes is calculated with the Gauss elimination method and the absolute permeability of the pore network is calculated directly from Darcy's law. Finally, the permeability model is validated by comparison with direct water permeability measurements. According to this model...

Evaluation of storage conditions for tritiated thymidine as reference organically-bound tritium in urine

International Nuclear Information System (INIS)

Duong, T.; Trivedi, A.

1997-01-01

Interlaboratory intercomparison exercises have used tritiated thymidine as a reference material for organically-bound tritium (OBT) measurements in urine. We have examined the effects of storage conditions on the degradation behavior of tritium from OBT to tritiated water (HTO) in artificial and natural human urine samples. Tritiated thymidine decomposed less readily in artificial urine than natural urine samples. The degradation rate of tritiated thymidine in artificial urine, at -20 deg C, is about 10% for the first month. The rate of tritium conversion from OBT to HTO is the same at 4 deg C, but this storage temperature is less preferable, because of the danger of microbial contamination in the reference samples. The storage of the reference urine samples beyond three months after the preparation date is not recommended for quality control measurement data. (author)

Synthesis of tritiated Lomoparan

International Nuclear Information System (INIS)

Kaspersen, F.M.; Schlachter, I.H.G.; Dedem, G.W.K. van

1991-01-01

Lomoparan (org. 10172) is a highly effective anti-thrombotic drug which is a mixture of low molecular weight glycosaminoglycuronans. Tritiated Org 10172 can be prepared through labelling of its subfractions and reconstitution of the original material. Two methods were applied: partial N-deacetylation with N 2 H 4 /HI0 3 followed by reacetylation with tritiated acetic anhydride and, more easily, reduction of end groups with NaB 3 H 4 . (UK)

Polysulfone - CNT composite membrane with enhanced water permeability

Science.gov (United States)

Hirani, Bhakti; Kar, Soumitra; Aswal, V. K.; Bindal, R. C.; Goyal, P. S.

2018-04-01

Polymeric membranes are routinely used for water purification. The performance of these conventional membranes can be improved by incorporating nanomaterials, such as metal oxide nanoparticle and carbon nanotubes (CNTs). This manuscript reports the synthesis and characterization of polysulfone (Psf) based nanocomposite membranes where multi wall carbon nanotubes (MWCNTs) and oleic acid coated Fe3O4 nanoparticles have been impregnated onto the polymeric host matrix. The performance of the membranes was evaluated by water permeability and solute rejection measurements. It was observed that the permeability of Psf membrane increases three times at 0.1% loading of MWCNT without compromise in selectivity. It was further observed that the increase in permeability is not affected upon addition of Fe3O4 nanoparticles into the membrane. In order to get a better insight into the membrane microstructure, small angle neutron scattering (SANS) studies were carried out. There is a good correlation between the water permeability and the pore sizes of the membranes as measured using SANS.

Radiobiological effects of tritiated water short-term exposure on V79 clonogenic cell survival

DEFF Research Database (Denmark)

Siragusa, Mattia; Fredericia, Nina Pil Møntegaard; Jensen, Mikael

2018-01-01

We set out to improve the accuracy of absorbed dose calculations for in-vitro measurements of the Relative Biological Effectiveness (RBE) of tritiated water (HTO) for the clonogenic cell survival assay, also considering the influence of the end-of-track Linear Energy Transfer (LET) of low-energy...... in suspension are usually comparable to those for adherent cells. RBEs calculated at the 10% survival fraction through the use of the average energy are almost similar to those obtained with the beta-spectrum. For adherent cells, an RBE of 1.6 was found when HTO cell survival curves were compared to acute γ...

Effect Of Hot Water Injection On Sandstone Permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Fabricius, Ida Lykke

2012-01-01

of published results regarding the effect of temperature on sandstone permeability. These tests are performed with mineral oil, nitrogen gas, distilled water and solutions of NaCl, KCl, CaCl2 as well as brines that contain a mixture of salts. Thirteen sandstone formations, ranging from quartz arenites...... to formations with a significant fraction of fine particles including clay minerals are investigated. The porosities range from 0.10 to 0.30 and permeabilities span the range from 1 to 1000 md. To compare different rock types, specific surface is determined from permeability and porosity using Kozeny’s equation...... not account for all the permeability reductions observed. Permeablity reduction occurs both when distilled water is the saturating fluid as well as in tests with NaCl, KCl or CaCl2 solutions, however, this is not the case in tests with mineral oil or nitrogen gas. The formation of a filter cake or influx...

The water relations of mycorrhiza

International Nuclear Information System (INIS)

Leyton, L.

1982-01-01

The wettability of the surface of ectotrophic beech mycorrhiza roots which did not have any radiating hyphae, was much less than a non-mycorrhizal root epidermis. The mycorrhizal sheath has a lower permeability to the flow of water than the uninfected root. The mycorrhizal roots absorbed water more rapidly than non-mycorrhizal roots. Possible explanations for this unusual phenomenon were (1) the development of a lower water potential in water stressed mycorrhizal roots, (2) accummulation of absorbed water in the sheath and (3) a higher permeability of the sheath to incoming than outgoing water. A study with endotrophic red clover plants confirmed that infection markedly increased growth and P uptake. This was accompanied by a reduction in the root/shoot ratio. This could be explained by a faster recovery of stressed mycorrhizal plants when water was restored because they were more efficient in taking up water. Experiments with tritiated water (THO) were initiated but consistent values for conductivity were not obtained. (author)

Biological half-time of tritiated water: comparison of hyperthyroid and hypothyroid patients

Energy Technology Data Exchange (ETDEWEB)

Eberstadt, P; Fernandez, M V.G.; Gonzalez, O

1986-01-01

The half-time values of tritiated water were explored in eleven hyperthyroid patients and in two hypothyroid ones. For reasons of comparability the numbers are expressed in days per square meter (d/m/sup 2/) of body surface. Against the estimated 5.4d/m/sup 2/ in normal subjects, the hyperthyroids reflected 3.9+-0.66 and the two determinations of hypothyroids were 6.42 and 7.13, respectively. During the study neither diagnostic nor therapeutic procedures were ever postponed. The half-time values are not representative of extreme conditions in hyper- or hypothyroids, but are sufficiently clear to indicate well-defined differences from normal people. The total exposure to radiation for the exploratory procedure was minimal, estimated at less than 12 mrem for the normal standard man.

Effect of prenatal exposure to low dose beta radiation from tritiated water on postnatal growth and neurobehavior of rats

International Nuclear Information System (INIS)

Gao Weimin; Zhou Xiangyan

1998-01-01

Objective: Effects of prenatal exposure to HTO (tritiated water) on postnatal growth and neurobehavior of rats were studied by determination of multiple parameters. Methods: Pregnant adult Wistar rats were randomly assigned to 4 groups, of which 3 groups were irradiated with beta-rays from tritiated water (HTO) by one single intraperitoneal injection on the 13th day of gestation. Offspring of these rats received cumulative doses of 0.000, 0.044, 0.088 and 0.264 Gy utero, respectively, and were observed for the appearance of three physiologic markers (eye opening, pinna detachment, incisor eruption), the age of acquisition of two reflexes (surface righting, negative geotaxis) and sensuous function (auditory startle), movement and coordination functions and activity (forelimb hanging, continuous corridor activity), and learning and memory (electric avoidance reflex in Y-maze, conditional reflex). Results: Results for most parameters in the 0.044 and 0.088 Gy groups were different significantly from those in the controls and for most parameters a dose-dependent effect was found. Conclusion: Offspring of rats having received prenatal low dose irradiation from HTO showed delayed growth and abnormal neurobehavior

The long term effects of {sup 137}Cs {gamma}-rays and tritiated water on induction on teratogenesis in rats

Energy Technology Data Exchange (ETDEWEB)

Shoji, Shuneki [Hiroshima Univ., Research Institute for Radiation Biology and Medicine, Hiroshima (Japan)

2003-07-01

The purpose of the present study is to evaluate the teratogenesis caused by {sup 137}Cs {gamma}-rays radiation and tritiated water (tritium {beta}-rays, HTO) in rats under long-term exposures. Many congenital anomalies are caused by environmental factors, and it is likely that this assessment of teratogenesis will be very important in the future. Pregnant Donryu strain rats were irradiated with {sup 137}Cs {gamma}-rays on days 9-18 of gestation. The animals were sacrificed on day 18 of gestation and the contents of each uterine horn were examined. The numbers of surviving, dead and resorbed fetuses were recorded. The surviving fetuses were examined for external and visceral malformations. Also given here is a measure of the relative biological effectiveness (RBE) of tritiated water (HTO) compared to that for {sup 137}Cs {gamma}-rays regarding the induction of developmental anomalies such as neurocristopathy in pregnant Donryu rats. Radiation exposures were approximately 0, 1, 2, 3, 4, 5 and 6 Gy for both tritiated water and {sup 137}Cs {gamma}-rays. Teratogenesis was dose dependent for both radiation groups. Our studies show that {sup 137}Cs {gamma}-rays and HTO irradiation induce similar malformations of the cardiovascular, respiratory and skeletal systems in rat fetuses. However, a number of fetuses exhibiting growth retardation, general edema, persistent atrioventricular canal, eye defects, microcephaly and craniofacial defects following maternal exposure to HTO. These include hypoplasia of the pulmonary trunk (tetralogy of Fallot), DORV, ventricular septal defect, right aortic arch, coarctation of the aorta, aberrant right subclavian artery, hypoplasia of the thymus, craniofacial anomalies, hypoplasia or incomplete lungs and trachea, as well as limb and tail malformations in HTO syndrome. These results are similar to those found in human DiGeorge syndrome, which are considered pharyngeal arch syndromes related to a cephalic neutrocristopathy. A best estimation

Mathematical Model to Predict the Permeability of Water Transport in Concrete Structure

OpenAIRE

Solomon Ndubuisi Eluozo

2013-01-01

Mathematical model to predict the permeability of water transport in concrete has been established, the model is to monitor the rate of water transport in concrete structure. The process of this water transport is based on the constituent in the mixture of concrete. Permeability established a relation on the influence of the micropores on the constituent that made of concrete, the method of concrete placement determine the rate of permeability deposition in concrete structure, permeability es...

Chromosome aberrations in human lymphocytes exposed to tritiated water in vitro

International Nuclear Information System (INIS)

Bocian, E.; Ziemba-zak, B.; Rosiek, O.; Sablinski, J.

1978-01-01

The induction of chromosome aberrations in human peripheral blood lymphocytes by tritiated water or 180 kV X-rays in vitro was studied. Lymphocytes were exposed to various concentrations of HTO for 2 h or for 53 h. Chromosome and chromatid type aberrations were scored during the first mitotic division after stimulation with phytohaemagglutinin. For the analysis of the dose-response relationship the data were fitted by the method of least-squares to different models. After acute exposure to tritium β-rays and X-rays, the dicentrics + centric rings and terminal + interstitial deletions gave the best fit to the linear-quadratic function. However, data for these types of aberrations after 53 h exposure to HTO gave equally good fit to the linear and linear-quadratic functions. The best description of the dose-response relationship for chromatid aberrations is given by the linear model. In the system studied the RBE of tritium β-rays as compared to 180 KV X-rays was 1.17+-0.02. (Auth.)

Research on the performance of sand-based environmental-friendly water permeable bricks

Science.gov (United States)

Cai, Runze; Mandula; Chai, Jinyi

2018-02-01

This paper examines the effects of the amount of admixture, the water cement ratio, the aggregate grading, and the cement aggregate ratio on the mechanical service properties and of porous concrete pavement bricks including strength, water permeability, frost resistance, and wear resistance. The admixture can enhance the performance of water permeable brick, and optimize the design mix. Experiments are conducted to determine the optimal mixing ratios which are given as; (1) the admixture (self-developed) within the content of 5% of the cement quality; (2) water-cement ratio equal to 0.34; (3) cement-aggregate ratio equal to 0.25; (4) fine aggregate of 70% (particle size 0.6-2.36mm); and coarse aggregate of 30% (particle size: 2.36-4.75mm). The experimental results that the sand-based permeable concrete pavement brick has a strength of 35.6MPa and that the water permeability coefficient is equal to 3.5×10-2cm/s. In addition, it was found that the concrete water permeable brick has good frost resistance and surface wear resistance, and that the its production costs are much lower than the similar sand-based water permeable bricks in China.

Measurement of organ blood flow using tritiated water. II. Uterine blood flow in conscious pregnant ewes

International Nuclear Information System (INIS)

Brown, B.W.; Oddy, V.H.; Jones, A.W.

1982-01-01

Total uterine blood flow was measured with a tritiated water (TOH) diffusion method and with radioactive microspheres in six, conscious, pregnant ewes. With continuous infusion of TOH, equilibrium between the TOH concentration in utero-ovarian venous blood and arterial blood was attained within 50 min of the start of the infusion. The concentration of TOH in uterine and foetal tissue and in foetal blood water was the same as that in uterine venous water by 40 min; at this time, the concentration of TOH in the water of amniotic and allantoic fluids was 96% of that in uterine venous blood water. Estimates of total uterine blood flow obtained using TOH were highly correlated with those obtained with microspheres and the corresponding mean flow values obtained with the two techniques did not significantly differ. The percentage of the total uterine blood flow passing through arteriovenous anastomoses ranged from 1.4 to 3.3%

Water permeability is a measure of severity in acute appendicitis.

Science.gov (United States)

Pini, Nicola; Pfeifle, Viktoria A; Kym, Urs; Keck, Simone; Galati, Virginie; Holland-Cunz, Stefan; Gros, Stephanie J

2017-12-01

Acute appendicitis is the most common indication for pediatric abdominal emergency surgery. Determination of the severity of appendicitis on clinical grounds is challenging. Complicated appendicitis presenting with perforation, abscess or diffuse peritonitis is not uncommon. The question remains why and when acute appendicitis progresses to perforation. The aim of this study was to assess the impact of water permeability on the severity of appendicitis. We show that AQP1 expression and water permeability in appendicitis correlate with the stage of inflammation and systemic infection parameters, leading eventually to perforation of the appendix. AQP1 is also expressed within the ganglia of the enteric nervous system and ganglia count increases with inflammation. Severity of appendicitis can be correlated with water permeability measured by AQP1 protein expression and increase of ganglia count in a progressive manner. This introduces the question if regulation of water permeability can present novel curative or ameliorating therapeutic options.

Permeability of volcanic rocks to gas and water

Science.gov (United States)

Heap, M. J.; Reuschlé, T.; Farquharson, J. I.; Baud, P.

2018-04-01

The phase (gas or liquid) of the fluids within a porous volcanic system varies in both time and space. Laboratory experiments have shown that gas and water permeabilities can differ for the same rock sample, but experiments are biased towards rocks that contain minerals that are expected react with the pore fluid (such as the reaction between liquid water and clay). We present here the first study that systematically compares the gas and water permeability of volcanic rocks. Our data show that permeabilities to argon gas and deionised water can differ by a factor between two and five in two volcanic rocks (basalt and andesite) over a confining pressure range from 2 to 50 MPa. We suggest here that the microstructural elements that offer the shortest route through the sample-estimated to have an average radius 0.1-0.5 μm using the Klinkenberg slip factor-are accessible to gas, but restricted or inaccessible to water. We speculate that water adsorption on the surface of these thin microstructural elements, assumed here to be tortuous/rough microcracks, reduces their effective radius and/or prevents access. These data have important implications for fluid flow and therefore the distribution and build-up of pore pressure within volcanic systems.

Studies in uptake and turnover of tritiated water vapour (HTO) by vegetables. Untersuchungen zur Aufnahme und zum Umsatz von tritiiertem Wasserdampf (HTO) in Gemuesepflanzen

Energy Technology Data Exchange (ETDEWEB)

Roller, M.

1989-02-01

The aerial parts of vegetables were exposed to tritiated water vapour for up to three days in a plant growth chamber. The species used were Raphanus sativus L., Phaseolus vulgaris K. and Daucus carota L. (red radish, bean and carrot). The increase of specific activity of tissue free water as collected by freeze drying which was observed in the aerial parts of plants is explained by direct uptake of tritiated water vapour by the exposed part of the plant. It shows different characteristics for the several organs. No translocation of water from the laminae into other parts of the plant was observed. After combustion of dry matter tritium activity was detectable in the oxidation water for all parts of the plants. Kinetics of the specific activity of organically bound tritium in leaves can be described by a single curve. The lower - steep - part of the curve is increasing approximately with the uptake rate of HTO; this is explained by reversible binding of tritium by isotopic exchange reactions. The upper - flat - part of the curve represents tritium bound by light dependent reducing reactions of photosynthesis; it is increasing with a rate similar to the growth rate of leaves. (orig./KG).

Low pressure tritiation of molecules

International Nuclear Information System (INIS)

Moran, T.F.; Powers, J.C.; Lively, M.O.

1980-01-01

A method is described of tritiating sensitive biological molecules by depositing molecules of the substance to be tritiated on a supporting substrate in an evacuated vacuum chamber near, but not in the path of, an electron beam which traverses the chamber, admitting tritium gas into the chamber, and subjecting the tritium to the electron beam. Vibrationally excited tritium gas species are generated which collide and react with the substance thus incorporating tritium atoms into the substance. (U.K.)

Permeability of cork for water and ethanol.

Science.gov (United States)

Fonseca, Ana Luisa; Brazinha, Carla; Pereira, Helena; Crespo, Joao G; Teodoro, Orlando M N D

2013-10-09

Transport properties of natural (noncompressed) cork were evaluated for water and ethanol in both vapor and liquid phases. The permeability for these permeants has been measured, as well as the sorption and diffusion coefficients. This paper focuses on the differences between the transport of gases' relevant vapors and their liquids (water and ethanol) through cork. A transport mechanism of vapors and liquids is proposed. Experimental evidence shows that both vapors and liquids permeate not only through the small channels across the cells (plasmodesmata), as in the permeation of gases, but also through the walls of cork cells by sorption and diffusion as in dense membranes. The present study also shows that cork permeability for gases was irreversibly and drastically decreased after cork samples were exposed to ethanol or water in liquid phase.

Tritiated water uptake kinetics in tissue-free water and organically-bound fractions of tomato plants

International Nuclear Information System (INIS)

Spencer, F.S.

1984-03-01

The kinetics of tritiated water (HTO) vapour uptake into tissue-free water tritium (TFWT) and organically bound tritium (OBT) fractions of tomato, Lycopersicon esculentum Mill., cv Vendor, were investigated under controlled growing conditions. Most uptake data fitted a first-order kinetic model, C t = C ∞ (1-e -kt ), where C t is the tritium concentration at time t, Ca the steady-state concentration and k the uptake rate constant. During atmospheric-HTO exposure with clean-water irrigation in open pots the TFWT k values were 0.024 ± 0.023 h -1 for new foliage, 0.104 ± 0.067 h -1 for old foliage and 0.042 ± to 0.136 h -1 for new green fruit. OBT uptake rate constants were 20 percent less for new foliage and 76 percent less for new green fruit. Under steady-state conditions the ratio of tritium specific activities of TWFT to atmospheric HTO were 0.43 in new foliage, 0.46 in old foliage and 0.19 in green fruit. Within the plant, OBT and TFWT ratios were 0.70 for new foliage, 0.63 for old foliage (maximum) and between 0.72 and 1.92 for green fruit. The greater than unity tritium specific activity ratios in green fruit were not attributed to tritium enrichment but rather to the translocation of foliar OBT to the growing fruit which contained lower specific activity TFWT derived from soil water

Historical Doses from Tritiated Water and Tritiated Hydrogen Gas Released to the Atmosphere from Lawrence Livermore National Laboratory (LLNL). Part 5. Accidental Releases

Energy Technology Data Exchange (ETDEWEB)

Peterson, S

2007-08-15

Over the course of fifty-three years, LLNL had six acute releases of tritiated hydrogen gas (HT) and one acute release of tritiated water vapor (HTO) that were too large relative to the annual releases to be included as part of the annual releases from normal operations detailed in Parts 3 and 4 of the Tritium Dose Reconstruction (TDR). Sandia National Laboratories/California (SNL/CA) had one such release of HT and one of HTO. Doses to the maximally exposed individual (MEI) for these accidents have been modeled using an equation derived from the time-dependent tritium model, UFOTRI, and parameter values based on expert judgment. All of these acute releases are described in this report. Doses that could not have been exceeded from the large HT releases of 1965 and 1970 were calculated to be 43 {micro}Sv (4.3 mrem) and 120 {micro}Sv (12 mrem) to an adult, respectively. Two published sets of dose predictions for the accidental HT release in 1970 are compared with the dose predictions of this TDR. The highest predicted dose was for an acute release of HTO in 1954. For this release, the dose that could not have been exceeded was estimated to have been 2 mSv (200 mrem), although, because of the high uncertainty about the predictions, the likely dose may have been as low as 360 {micro}Sv (36 mrem) or less. The estimated maximum exposures from the accidental releases were such that no adverse health effects would be expected. Appendix A lists all accidents and large routine puff releases that have occurred at LLNL and SNL/CA between 1953 and 2005. Appendix B describes the processes unique to tritium that must be modeled after an acute release, some of the time-dependent tritium models being used today, and the results of tests of these models.

Water Permeability of Pervious Concrete Is Dependent on the Applied Pressure and Testing Methods

Directory of Open Access Journals (Sweden)

Yinghong Qin

2015-01-01

Full Text Available Falling head method (FHM and constant head method (CHM are, respectively, used to test the water permeability of permeable concrete, using different water heads on the testing samples. The results indicate the apparent permeability of pervious concrete decreasing with the applied water head. The results also demonstrate the permeability measured from the FHM is lower than that from the CHM. The fundamental difference between the CHM and FHM is examined from the theory of fluid flowing through porous media. The testing results suggest that the water permeability of permeable concrete should be reported with the applied pressure and the associated testing method.

Multi-column adsorption systems with condenser for tritiated water vapor removal

International Nuclear Information System (INIS)

Kotoh, Kenji; Kudo, Kazuhiko

1996-01-01

Two types of multi-column adsorption system are proposed as the system for removal of tritiated moisture from tritium process gases or/and handling room atmospheres. The types are of recycle use of adsorption columns, and are composed of twin or triplet columns and one condenser which is used for collecting the adsorbed moisture from columns in desorption process. The systems utilize the dry gas from a working column as the purge gas for regenerating a saturated column and appropriate an active column for recovery of the tritiated moisture passing through the condenser. Each column hence needs the additional amount of adsorbent for collecting the moisture from the condenser. In the modeling and design of an adsorption column, it is primary to estimate the necessary amount of a candidate adsorbent for its packed-bed. The performance of the proposed systems is examined here by analyzing the dependence of the necessary amount of adsorbent for their columns on process operational conditions and adsorbent moisture-adsorption characteristics. The result shows that the necessary amount is sensitive to the types of adsorption isotherm, and suggests that these systems should employ adsorbents which exhibit the Langmuir-type isotherms. (author)

Analytical Estimation of Water-Oil Relative Permeabilities through Fractures

Directory of Open Access Journals (Sweden)

Saboorian-Jooybari Hadi

2016-05-01

Full Text Available Modeling multiphase flow through fractures is a key issue for understanding flow mechanism and performance prediction of fractured petroleum reservoirs, geothermal reservoirs, underground aquifers and carbon-dioxide sequestration. One of the most challenging subjects in modeling of fractured petroleum reservoirs is quantifying fluids competition for flow in fracture network (relative permeability curves. Unfortunately, there is no standard technique for experimental measurement of relative permeabilities through fractures and the existing methods are very expensive, time consuming and erroneous. Although, several formulations were presented to calculate fracture relative permeability curves in the form of linear and power functions of flowing fluids saturation, it is still unclear what form of relative permeability curves must be used for proper modeling of flow through fractures and consequently accurate reservoir simulation. Basically, the classic linear relative permeability (X-type curves are used in almost all of reservoir simulators. In this work, basic fluid flow equations are combined to develop a new simple analytical model for water-oil two phase flow in a single fracture. The model gives rise to simple analytic formulations for fracture relative permeabilities. The model explicitly proves that water-oil relative permeabilities in fracture network are functions of fluids saturation, viscosity ratio, fluids density, inclination of fracture plane from horizon, pressure gradient along fracture and rock matrix wettability, however they were considered to be only functions of saturations in the classic X-type and power (Corey [35] and Honarpour et al. [28, 29] models. Eventually, validity of the proposed formulations is checked against literature experimental data. The proposed fracture relative permeability functions have several advantages over the existing ones. Firstly, they are explicit functions of the parameters which are known for

Water sorption and water permeability properties of edible film made from potato peel waste

Directory of Open Access Journals (Sweden)

Siti Hajar OTHMAN

Full Text Available Abstract The water sorption and permeability properties of edible film produced from potato peel waste was investigated under different levels of relative humidity (23, 33, 43, 57, 75% RH and temperatures (5, 30, 50 °C. The water sorption behaviour and isotherms of the film were investigated by fitting water sorption data to the Peleg model and the Guggenheim, Anderson de Boer model (GAB model. The amount of moisture content, time required for the moisture content of the film to reach equilibrium, water sorption rate, and water sorption capacity increased when the relative humidity increased. The effect of temperature on moisture content, water sorption rate, water sorption capacity, and monolayer moisture content is complex and related to the water activity as well as the moisture content. Based on R2 and RMSE values, the Peleg and GAB models were respectively determined as excellent models to predict the water sorption properties of the films, thus supporting the reliability of water sorption behaviour prediction. The water vapour transmission rate and water vapour permeability increased with an increase in relative humidity and temperature. The sorption and permeability properties of the film are worth investigation since the final application of the film as food packaging is ultimately dependent on these behaviours.

Conditioning and handling of tritiated wastes at Canadian nuclear power facilities

International Nuclear Information System (INIS)

Krochmalnek, L.S.; Krasznai, J.P.; Carney, M.

1987-04-01

Ontario Hydro operates a 10,000 MW capacity nuclear power system utilizing the CANDU pressurized heavy water reactor design. The use of D 2 O as moderator and coolant results in the production of about 2400 Ci of tritium per MWe-yr. As a result, there is significant Canadian experience in the treatment, handling, transport and storage of tritiated wastes. Ontario Hydro operates its own reactor waste storage site which includes systems for volume reduction, immobilization and packaging of wastes. In addition, a facility to remove tritium from heavy water is presently being commissioned at the Darlington nuclear site. This facility will generate tritiated liquid and solid waste that will have to be properly conditioned prior to storage or disposal. The nature of these various wastes and the processes/packaging required to meet storage/disposal criteria are judged to have relevance to investigations in fusion facility waste arisings. Experience to date, planned operational procedures and ongoing R and D in this area are described

Polybenzimidazole-based mixed membranes with exceptional high water vapor permeability and selectivity

KAUST Repository

Akhtar, Faheem Hassan

2017-09-13

Polybenzimidazole (PBI), a thermal and chemically stable polymer, is commonly used to fabricate membranes for applications like hydrogen recovery at temperatures of more than 300 °C, fuel cells working in a highly acidic environment, and nanofiltration in aggressive solvents. This report shows for the first time use of PBI dense membranes for water vapor/gas separation applications. They showed an excellent selectivity and high water vapor permeability. Incorporation of inorganic hydrophilic titanium-based nano-fillers into the PBI matrix further increased the water vapor permeability and water vapor/N2 selectivity. The most selective mixed matrix membrane with 0.5 wt% loading of TiO2 nanotubes yielded a water vapor permeability of 6.8×104 Barrer and a H2O/N2 selectivity of 3.9×106. The most permeable membrane with 1 wt% loading of carboxylated TiO2 nanoparticles had a 7.1×104 Barrer water vapor permeability and a H2O/N2 selectivity of 3.1×106. The performance of these membranes in terms of water vapor transport and selectivity is among the highest reported ones. The remarkable ability of PBI to efficiently permeate water versus other gases opens the possibility to fabricate membranes for dehumidification of streams in harsh environments. This includes the removal of water from high temperature reaction mixtures to shift the equilibrium towards products.

Polybenzimidazole-based mixed membranes with exceptional high water vapor permeability and selectivity

KAUST Repository

Akhtar, Faheem Hassan; Kumar, Mahendra; Villalobos, Luis Francisco; Shevate, Rahul; Vovusha, Hakkim; Schwingenschlö gl, Udo; Peinemann, Klaus-Viktor

2017-01-01

Polybenzimidazole (PBI), a thermal and chemically stable polymer, is commonly used to fabricate membranes for applications like hydrogen recovery at temperatures of more than 300 °C, fuel cells working in a highly acidic environment, and nanofiltration in aggressive solvents. This report shows for the first time use of PBI dense membranes for water vapor/gas separation applications. They showed an excellent selectivity and high water vapor permeability. Incorporation of inorganic hydrophilic titanium-based nano-fillers into the PBI matrix further increased the water vapor permeability and water vapor/N2 selectivity. The most selective mixed matrix membrane with 0.5 wt% loading of TiO2 nanotubes yielded a water vapor permeability of 6.8×104 Barrer and a H2O/N2 selectivity of 3.9×106. The most permeable membrane with 1 wt% loading of carboxylated TiO2 nanoparticles had a 7.1×104 Barrer water vapor permeability and a H2O/N2 selectivity of 3.1×106. The performance of these membranes in terms of water vapor transport and selectivity is among the highest reported ones. The remarkable ability of PBI to efficiently permeate water versus other gases opens the possibility to fabricate membranes for dehumidification of streams in harsh environments. This includes the removal of water from high temperature reaction mixtures to shift the equilibrium towards products.

Water permeability in human airway epithelium

DEFF Research Database (Denmark)

Pedersen, Peter Steen; Procida, Kristina; Larsen, Per Leganger

2005-01-01

Osmotic water permeability (P(f)) was studied in spheroid-shaped human airway epithelia explants derived from nasal polyps by the use of a new improved tissue collection and isolation procedure. The fluid-filled spheroids were lined with a single cell layer with the ciliated apical cell membrane ...

Water permeability of pigmented waterborne coatings

NARCIS (Netherlands)

Donkers, P.A.J.; Huinink, H.P.; Erich, S.J.F.; Reuvers, N.J.W.; Adan, O.C.G.

2013-01-01

Coatings are used in a variety of applications. Last decades more and more coating systems are transforming from solvent to waterborne coating systems. In this study the influence of pigments on the water permeability of a waterborne coating system is studied, with special interest in the possible

Tritiated thymidine and deoxycytidine suicide of mouse hemopoietic colony forming cells (CFC)

International Nuclear Information System (INIS)

Uyeki, E.M.; Wierzba, K.; Bisel, T.U.

1981-01-01

Significant enhancement of tritiated dCyd suicide occurred when unlabelled dThd was added to cultures of mouse monocytic colony-forming cells. Incorporation experiments supported the suicide experiments in that incorporation of tritiated dCyd into DNA was significantly increased. One hundred micromolar dCyd significantly reduced the radiotoxicity of 0.3 μCi of tritiated dThd; incorporation experiments indicated a dose-related reduction in the incorporation of tritiated dThd into DNA with the addition of 1-100 μM unlabelled dCyd. The addition of 1 μM aminopterin reversed the effect of 100 μM deoxycytidine; viz., incorporation of dThd into DNA was 90% of controls. Aminopterin had a similar effect on deoxyuridine reversal of tritiated dThd incorporation into DNA. Aminopterin had no effect on the reduction of tritiated dThd incorporation into DNA due to the addition of 100 μM unlabelled thymidine. Unlabelled ribonucleosides, Urd and Cyd, did not significantly affect the suicide pattern of tritiated dThd or dCyd when they were added to CFC cultures. Unlabelled deoxyribonucleosides, dThd or dCyd, did not significantly affect the suicide pattern of either tritiated Cyd or Urd when they were added to cultures containing tritiated ribonucleosides. Unlabelled Urd or Cyd was effective in reversing the suicide due to tritiated Urd or Cyd. (author)

Effect of injection water quality on permeability of productive sands in Shaimsk group of oil fields

Energy Technology Data Exchange (ETDEWEB)

Andreeva, N I; Ivanov, V N; Lazarev, V N; Maksimov, V P

1966-01-01

Water from the Kond River is used to flood Shaimsk oil fields. Effect of raw and filtered waters on permeability of Shaimsk cores was experimentally determined. The raw river water contained 26 mg/liter of suspended solids, 10.7 mg/liter of total iron, 4.3 mg/liter of suspended iron oxide, and a pH of 6.4. The filtered river water was free of suspended solids and had a pH of 6.2. It was found that both raw and filtered water decreased core permeability. The unfiltered water decreased permeability 2 to 7 times more than the filtered water. Also, the decrease in permeability occurs much more slowly with the filtered than the unfiltered water. The effect of water on core permeability is essentially irreversible. Efforts to restore core permeability by reversing flow direction were not successful. Among the reasons for the permeability decrease were hydration and swelling of clays and evolution of gases from water in the cores. (10 refs.)

METHODOLOGY FOR CALCULATION OF HORIZONTAL WATER PERMEABILITY COEFFICIENT IN SOIL CAPILLARY BORDER

Directory of Open Access Journals (Sweden)

E. I. Michnevich

2011-01-01

Full Text Available The paper shows that for overall estimation of soil water permeability it is necessary to know a horizontal water permeability value of a soil capillary border in addition to coefficients of filtration and permeability. Relations allowing to determine soil permeability in the area of incomplete saturation, are given in the paper. For a fully developed capillary border some calculation formulae have been obtained in the form of algebraic polynomial versus soil grading (grain composition. These formulae allow to make more accurate calculations while designing and operating  reclamation works.

The effects of tritiated water on some developmental stages of tilapia nilotica

International Nuclear Information System (INIS)

Carino, V.S.

1986-01-01

Seven developmental stages of Tilapia nilotica from gastrula (11 hr) to the active feeding and free swimming stage (10-d) were reared in tritiated water of concentrations 10 -3 10 -2 and 10 -1 Ci 1 -1 . The fish were reared for different lengths of time, the first group for the period till the next developmental stage and the second group till 3 weeks of age or day 21. Treated and control specimens were compared. An over-all delay in development was noted both at the gross morphological and the histological levels in the experimental fish. Growth was stunted. Many had unresorped yolk which was observable externally in the distended abdomens and histologically within the liver. Percent survival was lower in the treated fish and this was, in general, inversely related to developmental stage and tritium concentration of the rearing water. Posthatch larvae were sluggish to inactive. The liver exhibited histological aberrations which include the presence of adipose cells in place of liver parenchyma in the more anterior liver regions. Brains of treated fish, in general were smaller. One instance of an abnormal brain growth and findings on the retinal epithelium, spleen and pancreas are described. Development of gonads and digestive tract was, in general, retarded. (Auth.) 40 refs.; 5 tabs

Measurement of capacity coefficient of inclined liquid phase catalytic exchange column for tritiated water processing

International Nuclear Information System (INIS)

Yamai, Hideki; Konishi, Satoshi; Yamanishi, Toshihiko; Okuno, Kenji

1994-01-01

Liquid phase catalytic exchange (LPCE) is effective method for enrichment and removal of tritium from tritiated water. Capacity coefficients of operating LPCE column that are essential to evaluate column performance were measured. Experiments were performed with short catalyst packed columns and effect of inclination was studied. Method for evaluation of capacity coefficients was established from measurement of isotope concentration of liquid, vapor, gas phases at the two ends of the column. The capacity coefficients were measured under various superficial gas velocities. Feasibility study of helical columns with roughened inner surface was performed with short inclined columns. The column performance was not strongly affected by the inclination. The result indicates technological feasibility of helical LPCE column, that is expected to have operation stability and reduced height

Water permeability of nanoporous graphene at realistic pressures for reverse osmosis desalination

Energy Technology Data Exchange (ETDEWEB)

Cohen-Tanugi, David; Grossman, Jeffrey C. [Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

2014-08-21

Nanoporous graphene (NPG) shows tremendous promise as an ultra-permeable membrane for water desalination thanks to its atomic thickness and precise sieving properties. However, a significant gap exists in the literature between the ideal conditions assumed for NPG desalination and the physical environment inherent to reverse osmosis (RO) systems. In particular, the water permeability of NPG has been calculated previously based on very high pressures (1000–2000 bars). Does NPG maintain its ultrahigh water permeability under real-world RO pressures (<100 bars)? Here, we answer this question by drawing results from molecular dynamics simulations. Our results indicate that NPG maintains its ultrahigh permeability even at low pressures, allowing a permeate water flux of 6.0 l/h-bar per pore, or equivalently 1041 ± 20 l/m{sup 2}-h-bar assuming a nanopore density of 1.7 × 10{sup 13} cm{sup −2}.

Penetration of protective gloves as a route of intake for tritiated water and 125I-labelled sodium iodine solution

International Nuclear Information System (INIS)

Harris, S.J.; Gilmore, A.

1980-01-01

Measurements have been made of the rate at which tritiated water and 125 I-labelled sodium iodide solution penetrate various types of protective gloves, both isotopes being in common use in this form in universities and similar establishments. Diffusion coefficients relating to the glove materials are also determined. The health physics aspects are discussed and it is concluded that intakes by workers through intact gloves are not likely to be of major significance and can easily be minimised by the correct use and choice of glove. (author)

Tritiation and Stability Measurements of Nitroxide for Betavoltaic Cells

Science.gov (United States)

2016-09-01

source compounds include low beta-flux power, intrinsic isotope leakage , and beta self-absorption. The figure of merit for a tritiated compound is...graphane, fully hydrogenated graphene. Graphane is not reactive in water or air; it has theoretical higher mechanical and thermal strength than graphene...bonded to the side group of the nitroxide radical TEMPO 6-membered ring. The ester-cleaved product is detectable and is used to assess the specific

A fractal model for predicting permeability and liquid water relative permeability in the gas diffusion layer (GDL) of PEMFCs

Science.gov (United States)

He, Guangli; Zhao, Zongchang; Ming, Pingwen; Abuliti, Abudula; Yin, Caoyong

In this study, a fractal model is developed to predict the permeability and liquid water relative permeability of the GDL (TGP-H-120 carbon paper) in proton exchange membrane fuel cells (PEMFCs), based on the micrographs (by SEM, i.e. scanning electron microscope) of the TGP-H-120. Pore size distribution (PSD), maximum pore size, porosity, diameter of the carbon fiber, pore tortuosity, area dimension, hydrophilicity or hydrophobicity, the thickness of GDL and saturation are involved in this model. The model was validated by comparison between the predicted results and experimental data. The results indicate that the water relative permeability in the hydrophobicity case is much higher than in the hydrophilicity case. So, a hydrophobic carbon paper is preferred for efficient removal of liquid water from the cathode of PEMFCs.

Treatment of tritiated exhaust gases at the Tritium Laboratory Karlsruhe

Energy Technology Data Exchange (ETDEWEB)

Hutter, E.; Besserer, U. [Kernforschungszentrum Karlsruhe GmbH (Germany); Jacqmin, G. [NUKEM GmbH, Industreistr, Alzenau (Germany)

1995-02-01

The Tritium Laboratory Karlsruhe (TLK) accomplished commissioning; tritium involving activities will start this year. The laboratory is destined mainly to investigating processing of fusion reactor fuel and to developing analytic devices for determination of tritium and tritiated species in view of control and accountancy requirements. The area for experimental work in the laboratory is about 800 m{sup 2}. The tritium infrastructure including systems for tritium storage, transfer within the laboratory and processing by cleanup and isotope separation methods has been installed on an additional 400 m{sup 2} area. All tritium processing systems (=primary systems), either of the tritium infrastructure or of the experiments, are enclosed in secondary containments which consist of gloveboxes, each of them connected to the central depressurization system, a part integrated in the central detritiation system. The atmosphere of each glovebox is cleaned in a closed cycle by local detritiation units controlled by two tritium monitors. Additionally, the TLK is equipped with a central detritiation system in which all gases discharged from the primary systems and the secondary systems are processed. All detritiation units consist of a catalyst for oxidizing gaseous tritium or tritiated hydrocarbons to water, a heat exchanger for cooling the catalyst reactor exhaust gas to room temperature, and a molecular sieve bed for adsorbing the water. Experiments with tracer amounts of tritium have shown that decontamination factors >3000 can be achieved with the TLK detritiation units. The central detritiation system was carefully tested and adjusted under normal and abnormal operation conditions. Test results and the behavior of the tritium barrier preventing tritiated exhaust gases from escaping into the atmosphere will be reported.

Contributions of the CEA-Valduc Centre control to the understanding of the transfers of atmospheric tritiated water into the different parts of the environment; Apports de la surveillance du Centre CEA-Valduc sur la connaissance des transferts de l'eau tritiee atmospherique dans les differents compartiments de l'environnement

Energy Technology Data Exchange (ETDEWEB)

Guetat, P.; Vichot, L. [CEA Valduc, UMR, 21 - Is-sur-Tille (France); Tognelli, A. [CEA Bruyeres-le-Chatel, 91 (France)

2009-07-01

After a description of the geological environment of the Valduc Centre dedicated to tritium purification and tritiated waste processing and storage, this document presents the assessment of quantities of tritiated water released by the Valduc Centre and of their evolution in the hydro-geological environment. It provides in situ macroscopically observed data on the transfer mechanisms of water into the different parts of the environment and into the food chain by means. This is made possible by the exceptional traceability of tritiated water. Finally, a comparison between computational models and experimental measurements is given

Tritium distribution in newborn mice after providing mother mice with drinking water containing tritiated thymidine

International Nuclear Information System (INIS)

Saito, M.; Streffer, C.; Molls, M.

1983-01-01

Throughout gestation pregnant mice received drinking water which contained [methyl- 3 H]thymidine (18.5 kBq/ml). The newborn mice were divided into two groups. One group was nursed by their own mothers, which were further supplied with tritiated thymidine until 4 weeks after delivery (Experiment I). The other group was nursed by ''nonradioactive mothers'' which were given no tritiated thymidine (Experiment II). Tritium incorporation into the small molecular components of the acid-soluble fraction, lipid, RNA, DNA, and protein was analyzed for the newborn mice at various ages. In Experiment II, total radioactivity per gram tissue decreased initially after birth with a half life of 2.5-2.9 days in spleen, liver, intestine, stomach, thymus, lung, kidney, heart, and brain. At about 2 weeks after birth, a slower component of tritium elimination due mainly to the DNA-bound tritium appeared. Specific activity of DNA at birth was organ specific, highest in heart and lowest in thymus. Cumulative absorbed dose in various organs was estimated for the first 4 weeks after birth based upon an assumption that total and DNA-bound tritium are uniformly distributed. The result showed that organ specificity of dose accumulation is obvious for DNA-bound tritium, highest in spleen (1.15 mGy) and lowest in brain (0.13 mGy). It was also shown that the tritium supply from mother's milk is of minor importance for dose accumulation of DNA-bound tritium in the cell nuclei of organs of suckling mice

Tritium distribution in newborn mice after providing mother mice with drinking water containing tritiated thymidine

International Nuclear Information System (INIS)

Saito, M.; Streffer, C.; Molls, M.

1983-01-01

Throughout gestation pregnant mice received drinking water which contained [methyl- 3 H]thymidine (18.5 kBq/ml). The newborn mice were divided into two groups. One group was nursed by their own mothers, which were further supplied with tritiated thymidine until 4 weeks after delivery (Experiment I). The other group was nursed by nonradioactive mothers which were given no tritiated thymidine (Experiment II). Tritium incorporation into the small molecular components of the acid-soluble fraction, lipid, RNA, DNA, and protein was analyzed for the newborn mice at various ages. In Experiment II, total radioactivity per gram tissue decreased initially after birth with a half life of 2.5 to 2.9 days in spleen, liver, intestine, stomach, thymus, lung, kidney, heart, and brain. At about 2 weeks after birth, a slower component of tritium elimination due mainly to the DNA-bound tritium appeared. Specific activity of DNA at birth was organ specific, highest in heart and lowest in thymus. Cumulative absorbed dose in various organs was estimated for the first 4 weeks after birth based upon an assumption that total and DNA-bound tritium are uniformly distributed. The result showed that organ specificity of dose accumulation is obvious for DNA-bound tritium, highest in spleen (1.15 mGy) and lowest in brain (0.13 mGy). It was also shown that the tritium supply from mother's milk is of minor importance for dose accumulation of DNA-bound tritium in the cell nuclei of organs of suckling mice

Excretion of organic and inorganic tritiated compounds in cow's milk after ingestion of tritium oxide

International Nuclear Information System (INIS)

Van den Hoek, J.; Gerber, G.B.; Kirchmann, R.

1980-01-01

The secretion of tritium in milk as water, casein and lipids was studied in cows given tritiated water to drink for 25 days. The parameters of the exponential functions describing the secretion of tritium as water, casein and lipid are determined during this 'loading phase' and also for a 'decay period' of 75 days after the tritiated water administration had been terminated. Secretion started after a short delay (0.5 day). Turnover of all three compounds was short (half time of about 5 days). Calculations of the dilution of the ingested water during metabolism showed that about 83% of the milk water secreted is found to originate from drinking water; the rest comes from water in food and from that formed in metabolism. The parameters of the decay phase indicated that the principle components of water, casein and lipids had about the same turnover rates as during the loading phase. Using the loading and decay phase data, calculations were performed to determine how much activity in each compound and in each metabolic component would be excreted after a single and after a continuous application of tritium oxide when integrated over infinite times. (UK)

Water excretion mechanisms of the kidney studied in the rabbit using tritiated water during the stop-flow assay; Les mecanismes d'excretion de l'eau par le rein etudies a l'aide d'eau tritiee chez le lapin au cours de l'epreuve de diurese interrompue

Energy Technology Data Exchange (ETDEWEB)

Morel, F.; Amiel, CI.; Falbriard, A. [Commissariat a l' energie atomique et aux energies alternatives - CEA, Service de Biologie (France)

1960-07-01

The pattern of water turnover in the kidney and the mechanisms of water transfer into the urine have been studied in the rabbit using tritiated water as a tracer and the stop-flow technique. The experiments have given the following results: a) During the interruption of the diuresis, the injected tritiated water is completely exchanged with the water of the renal cortex, but the tracer does not reach the deep regions of the kidney, despite the fact that the blood circulation is maintained in these regions; this suggests that the vascular loops of the vasa recta function as a mechanism of water exchange by countercurrent. b) During the osmotic polyuria following the stop-flow period, the concentration gradient of tritiated water inside the kidney diminishes progressively. The concentration of the tracer in the urine is at all time similar to that existing in the deep medulla and the renal papilla and markedly different from that of the cortex or arterial blood. This fact shows that the molecules of water in the urine excreted do not come from either the glomerular filtrate or the convoluted tubules but from the water contained in the deep regions of the kidney. Also these results indicate that the walls of the collecting ducts have a very high permeability to water diffusion. Reprint of a paper published in Revue francaise d'etudes cliniques et biologiques, Vol. IV, no. 8, p. 773-779, 1959 [French] Les modalites du renouvellement de l'eau dans le rein et les mecanismes de son passage dans l'urine ont ete etudies chez le lapin a l'aide d'eau tritiee, employee comme indicateur au cours de l'epreuve de 'diurese interrompue' (stop flow). Les experiences effectuees montrent que: a) pendant l'interruption de la diurese, l'eau tritiee injectee s'echange completement avec l'eau contenue dans le cortex renal, mais elle n'atteint pratiquement pas les regions profondes du rein, bien que la circulation sanguine y soit maintenue; cette observation suggere que les anses

Quantitative Raman microspectroscopy for water permeability parameters at a droplet interface bilayer.

Science.gov (United States)

Braziel, S; Sullivan, K; Lee, S

2018-01-29

Using confocal Raman microspectroscopy, we derive parameters for bilayer water transport across an isolated nanoliter aqueous droplet pair. For a bilayer formed with two osmotically imbalanced and adherent nanoliter aqueous droplets in a surrounding oil solvent, a droplet interface bilayer (DIB), the water permeability coefficient across the lipid bilayer was determined from monitoring the Raman scattering from the C[triple bond, length as m-dash]N stretching mode of K 3 Fe(CN) 6 as a measure of water uptake into the swelling droplet of a DIB pair. We also derive passive diffusional permeability coefficient for D 2 O transport across a droplet bilayer using O-D Raman signal. This method provides a significant methodological advance in determining water permeability coefficients in a convenient and reliable way.

Durable Suit Bladder with Improved Water Permeability for Pressure and Environment Suits

Science.gov (United States)

Bue, Grant C.; Kuznetz, Larry; Orndoff, Evelyne; Tang, Henry; Aitchison, Lindsay; Ross, Amy

2009-01-01

Water vapor permeability is shown to be useful in rejecting heat and managing moisture accumulation in launch-and-entry pressure suits. Currently this is accomplished through a porous Gortex layer in the Advanced Crew and Escape Suit (ACES) and in the baseline design of the Constellation Suit System Element (CSSE) Suit 1. Non-porous dense monolithic membranes (DMM) that are available offer potential improvements for water vapor permeability with reduced gas leak. Accordingly, three different pressure bladder materials were investigated for water vapor permeability and oxygen leak: ElasthaneTM 80A (thermoplastic polyether urethane) provided from stock polymer material and two custom thermoplastic polyether urethanes. Water vapor, carbon dioxide and oxygen permeability of the DMM's was measured in a 0.13 mm thick stand-alone layer, a 0.08 mm and 0.05 mm thick layer each bonded to two different nylon and polyester woven reinforcing materials. Additional water vapor permeability and mechanical compression measurements were made with the reinforced 0.05 mm thick layers, further bonded with a polyester wicking and overlaid with moistened polyester fleece thermal underwear .This simulated the pressure from a supine crew person. The 0.05 mm thick nylon reinforced sample with polyester wicking layer was further mechanically tested for wear and abrasion. Concepts for incorporating these materials in launch/entry and Extravehicular Activity pressure suits are presented.

Study on the biological half-life and organ-distribution of tritiated lysine-vasopressin in Brattleboro rats

International Nuclear Information System (INIS)

Laczi, F.; Laszlo, F.A.; Keri, Gy.; Teplan, I.

1980-01-01

The biological half-life and organ-distribution of tritiated lysine-vasopressin were determined in R-Amsterdam rats, and in homozygous and heterozygous Brattleboro rats with hereditary central diabetes insipidus. It was found that the biological half-life of the tritiated lysin-vasopressin in the Brattleboro rats did not differ significantly from that found in the R-Amsterdam rats. The highest radioactivities were observed in the neuro- and adenohypophyses and in the kidneys of both the R-Amsterdam and the Brattleboro rats. The accumulation of tritiated LVP was higher in the small intestine of the Brattleboro rats than in that of the R-Amsterdam animals. The results have led to the conclusion that the accelerated elimination of vasopressin and its pathologic organ-accumulation are probably not involved in the water metabolism disturbance of Brattleboro rats with hereditary hypothalamic diabetes insipidus. (author)

Permeability of skin and oral mucosa to water and horseradish peroxidase as related to the thickness of the permeability barrier

International Nuclear Information System (INIS)

Squier, C.A.; Hall, B.K.

1985-01-01

The permeability of porcine skin and keratinized and nonkeratinized oral mucosa to tritium-labeled water and horseradish peroxidase (HRPO) was determined using perfusion chambers. Small blocks from each tissue were also incubated with HRPO and the extent of penetration visualized microscopically; this enabled measurements to be made of the thickness of the permeability barrier to this water-soluble tracer. Results obtained after inverting the oral mucosa in the chambers or adding metabolic inhibitors indicated that both compounds diffuse across the tissue. The permeability constants derived directly in the study showed that skin was less permeable than oral mucosa and that the floor of the mouth was significantly more permeable than all other regions. When these constants were normalized in terms of a standard permeability barrier thickness and the different tissues compared, the values obtained for skin were again less than those of the oral regions but, of these, the buccal mucosa was significantly higher. The difference in permeability between epidermis and keratinized oral epithelium may be due to differences in the volume density of membrane-coating granules known to exist between the tissues; differences between the oral mucosal regions may reflect differences in the nature of the intercellular barrier material

Fixation and long-term accumulation of tritium from tritiated water in an experimental aquatic environment

International Nuclear Information System (INIS)

Strand, J.A.; Templeton, W.L.; Olson, P.A.

1975-01-01

The accumulation of tritium in selected freshwater biota was studied in a 10 m diameter concrete-lined pond at the Hanford Atomic Energy Works. Tritium as tritiated water was introduced for 8 months continuously in the replacement water at a concentration of μCi per liter; and water, biota (carp, clams, crayfish, periphyton, pondweed), and sediments were sampled on a predetermined schedule. The pond was maintained on uncontaminated replacement waters for an additional 8 months to determine the rate of elimination from the ecosystem. After the first day, tissue-free-water tritium in all biota approached an equilibrium with pond water. Final concentration factors of 0.89, 0.87, 0.82, 0.92, 0.77, 0.88 were calculated for carp, clam, crayfish, snail, periphyton, and pondweed. Although highly variable, analyses of pond sediments suggested an initial rapid uptake by the loose water fraction, attaining 0.30 of the pond equilibrium level in three days. There was evidence to suggest a secondary slower rate of uptake that accounted for 0.65 of the pond equilibrium level as determined at seven months. Tissue-bond tritium initially increased rapidly in all biota sampled, but slowed with time. Equilibrium conditions were not reached. Final concentration factors for carp, clam, crayfish, snail, periphyton, and pondweed were calculated to be 0.49, 0.10, 0.53, 0.54, 0.15, and 0.62. Analyses of sediments after removal of the loose water fraction revealed little or no organically bound tritium

Laboratory test investigations on soil water characteristic curve and air permeability of municipal solid waste.

Science.gov (United States)

Shi, Jianyong; Wu, Xun; Ai, Yingbo; Zhang, Zhen

2018-05-01

The air permeability coefficient has a high correlation with the water content of municipal solid waste. In this study, continuous drying methodology using a tension meter was employed to construct the soil water characteristic curve of municipal solid waste (M-SWCC). The municipal solid waste air permeability test was conducted by a newly designed apparatus. The measured M-SWCC was well reproduced by the van Genuchten (V-G) model and was used to predict the parameters of typical points in M-SWCC, including saturated water content, field capacity, residual water content and water content at the inflection point. It was found that the M-SWCC was significantly influenced by void ratio. The final evaporation and test period of M-SWCC increase with the increase in void ratio of municipal solid waste. The evolution of air permeability coefficient with water content of municipal solid waste depicted three distinct characteristic stages. It was observed that the water contents that corresponded to the two cut-off points of the three stages were residual water content and water content at the inflection point, respectively. The air permeability coefficient of municipal solid waste decreased with the increase of the water content from zero to the residual water content. The air permeability coefficient was almost invariable when the water content increased from residual water content to the water content at the inflection point. When the water content of municipal solid waste exceeded the water content at the inflection point, the air permeability coefficient sharply decreased with the increase of water content.

Synthesis of adenosine triphosphate tritiated in position 2 and 8

International Nuclear Information System (INIS)

Cossery, Jean-Michel

1986-01-01

Adenosine triphosphate or ATP is an important molecule present at the cellular level in many fundamental biochemical mechanism, and the study of its metabolism is therefore of particular interest. In this thesis for pharmacy graduation, the author first describes the different steps of synthesis and purification leading to chloride-2-ATP, a precursor of the final tritiated molecule. Then, the author explains the tritiation of this molecule to obtain an ATP tritiated in position 2 and in position 8 [fr

Quantitation of biological retinoids by high-pressure liquid chromatography: primary internal standardization using tritiated retinoids

International Nuclear Information System (INIS)

Cullum, M.E.; Zile, M.H.

1986-01-01

A single method is described for quantitation of 14 retinoids found in biological material. The method consists of reversed-phase HPLC, internal standardization, and carrier extraction procedures with three synthetic retinoids. Primary standardization of HPLC uv detector is achieved using tritiated all-trans-retinoic acid, all-trans-retinol, all-trans-retinyl palmitate, and all-trans-retinyl acetate. Extraction methods are standardized by correlating the uv absorbance of retinoids at 340 nm with radioactivity of tritiated retinoids of known specific activity. Quantitation of 10 pg of tritiated or 5 ng of nonradioactive retinoid per 0.1 g sample in a polarity range from 4-oxo-retinoic acid to retinyl stearate can be achieved in a single, 50-min chromatographic run. A single HPLC pump, a C 18 reversed-phased analytical column, a multistep three-solvent gradient, and inexpensive solvents based on methanol, water, and chloroform comprise this cost-effective chromatographic system. Our primary standardization method allows investigators employing different procedures to compare results between laboratories by standardizing the HPLC uv detector with commercially available tritiated retinoids. With this method we were able to quantitate nanomolar amounts of endogenous retinoic acids and retinyl esters, that HPLC uv only conditions usually would not detect in the circulation and liver of rats under physiological conditions

Transfer of atmospheric tritiated water to foliage and fruit of crops

International Nuclear Information System (INIS)

Fellows, R.J.; Cataldo, D.A.; Ligotke, M.W.; Napier, B.A.

1993-01-01

Tritiated water (THO) released to the environment from the effluent streams of nuclear reactors may be easily assimilated by organisms through metabolic fixation following foliar interception of THO vapor. This study was initiated to characterize atmospheric THO exchange parameters in two crops agronomically important to eastern Washington, grape (Vitus vinifera) and alfalfa (Medicago sativa). Short-term exposures using atmospheric THO concentrations ranging from 458 to 1,300,900 pCi/m 3 indicated no statistically significant concentration influences on THO exchange into the leaf tissue free-water (TFW) and organically bound tritium (OBT) of the leaves of either species. Long-term exposures indicated that equilibration of the leaf TFW with atmospheric THO concentrations occurred within 24 to 48 h for both species while equilibration of grape TFW appeared to take over 20 days. The rate of THO saturation of the foliage TFW appeared to be directly related to the stomatal resistance of the leaves and fruit. Desorption rates from both leaves and fruit were greater in the light than in the dark, again correlating with stomatal resistance. More than 90% of the absorbed THO was lost from the leaf TFW pool within 24 h following cessation of exposure for both species, while loss of THO from grape TFW and OBT pools was minimal. It appeared that more than 95 to 98% of the THO found in the TFW and OBT pools of the grape fruit was of atmospheric origin and not from transport from other parts of the plant

Mass transfer behavior of tritium from air to water through the water surface

International Nuclear Information System (INIS)

Takata, Hiroki; Nishikawa, Masabumi; Kamimae, Kozo

2005-01-01

It is anticipated that a certain amount of tritiated water exists in the atmosphere of tritium handling facilities, and it is recognized that the hazardous potential of tritiated water is rather high. Then, it is important to grasp the behavior of tritiated water for preserving of the radiation safety. The mass transfer behavior of tritium from air to water through the water surface was discussed in this study. The evaporation rate of water and the condensation rate of water were experimentally examined from measurement of change of the weight of distilled water. The tritium transfer rate from the tritiated water in air to the distilled water was also experimentally examined by using a liquid scintillation counter. Experimental results about change of tritium level in a small beaker placed in the atmosphere with tritiated water showed that diffusion of tritium in water and gas flow in the atmosphere gives considerable effect on tritium transfer. The estimation method of the tritium transfer made in this study was applied to explain the data at The Japan Atomic Power Company second power station at Tsuruga and good agreement was obtained. (author)

The Effect of Green Inhibitor on strength and water permeability of ...

African Journals Online (AJOL)

... present in the concrete evident from inductively coupled plasma-mass spectrometry (ICPMS) result. KOH is adequate for passivation and reduction of permeability, which serve as a chemical water barriers or hydrophobic agents. Keywords: Concrete; Calcium-Silicate-Hydrate (C-S-H); Compressive strength; Permeability; ...

Water-Permeable Dialysis Membranes for Multi-Layered Micro Dialysis System

Directory of Open Access Journals (Sweden)

Naoya eTo

2015-06-01

Full Text Available This paper presents the development of water-permeable dialysis membranes that are suitable for an implantable microdialysis system that does not use dialysis fluid. We developed a microdialysis system integrating microfluidic channels and nanoporous filtering membranes made of polyethersulfone (PES, aiming at a fully implantable system that drastically improves the quality of life of patients. Simplicity of the total system is crucial for the implantable dialysis system, where the pumps and storage tanks for the dialysis fluid pose problems. Hence, we focus on hemofiltration, which does not require the dialysis fluid but water-permeable membranes. We investigated the water-permeability of the PES membrane with respect to the concentrations of the PES, the additives, and the solvents in the casting solution. Sufficiently water-permeable membranes were found through in vitro experiments using whole bovine blood. The filtrate was verified to have the concentrations of low-molecular-weight molecules, such as sodium, potassium, urea, and creatinine, while proteins, such as albumin, were successfully blocked by the membrane. We conducted in vivo experiments using rats, where the system was connected to the femoral artery and jugular vein. The filtrate was successfully collected without any leakage of blood inside the system and it did not contain albumin but low-molecular-weight molecules whose concentrations were identical to those of the blood. The rat model with renal failure showed 100% increase of creatinine in 5 h, while rats connected to the system showed only a 7.4% increase, which verified the effectiveness of the proposed microdialysis system.

Water detritiation processing of JET purified waste water using the TRENTA facility at Tritium Laboratory Karlsruhe

Energy Technology Data Exchange (ETDEWEB)

Michling, R., E-mail: robert.michling@kit.edu; Bekris, N.; Cristescu, I.; Lohr, N.; Plusczyk, C.; Welte, S.; Wendel, J.

2013-10-15

Highlights: • Operation of a water detritiation facility under optimized conditions for high detritiation performances. • Improvement of operational procedures to process tritiated waste water. • Handling and reduction of tritiated waste water to achieve enriched low volume tritiated water for sufficient storage. • Demonstration of the efficient availability of the TRENTA WDS facility for technical scale operation. -- Abstract: A Water Detritiation System (WDS) is required for any Fusion machine in order to process tritiated waste water, which is accumulated in various subsystems during operation and maintenance. Regarding the European procurement packages for the ITER tritium fuel cycle, the WDS test facility TRENTA applying the Combined Electrolysis Catalytic Exchange (CECE) process was developed, installed and is currently in operation at the Tritium Laboratory Karlsruhe (TLK). Besides the on-going R and D work for the design of ITER WDS, the current status of the TRENTA facility provides the option to utilize the WDS for processing tritiated water. Therefore, in the framework of the EFDA JET Fusion Technology Work Programme 2011, the TLK was able to offer the capability on a representative scale to process tritiated water, which was produced during normal operation at JET. The task should demonstrate the availability of the CECE process to handle and detritiate the water in terms of tritium enrichment and volume reduction. The operational program comprised the processing of purified tritiated water from JET, with a total volume of 180 l and an activity of 74 GBq. The paper will give an introduction to the TRENTA WDS facility and an overview of the operational procedure regarding tritiated water reduction. Data concerning required operation time, decontamination and enrichment performances and different operating procedures will be presented as well. Finally, a preliminary study on a technical implementation of processing the entire stock of JET

Water detritiation processing of JET purified waste water using the TRENTA facility at Tritium Laboratory Karlsruhe

International Nuclear Information System (INIS)

Michling, R.; Bekris, N.; Cristescu, I.; Lohr, N.; Plusczyk, C.; Welte, S.; Wendel, J.

2013-01-01

Highlights: • Operation of a water detritiation facility under optimized conditions for high detritiation performances. • Improvement of operational procedures to process tritiated waste water. • Handling and reduction of tritiated waste water to achieve enriched low volume tritiated water for sufficient storage. • Demonstration of the efficient availability of the TRENTA WDS facility for technical scale operation. -- Abstract: A Water Detritiation System (WDS) is required for any Fusion machine in order to process tritiated waste water, which is accumulated in various subsystems during operation and maintenance. Regarding the European procurement packages for the ITER tritium fuel cycle, the WDS test facility TRENTA applying the Combined Electrolysis Catalytic Exchange (CECE) process was developed, installed and is currently in operation at the Tritium Laboratory Karlsruhe (TLK). Besides the on-going R and D work for the design of ITER WDS, the current status of the TRENTA facility provides the option to utilize the WDS for processing tritiated water. Therefore, in the framework of the EFDA JET Fusion Technology Work Programme 2011, the TLK was able to offer the capability on a representative scale to process tritiated water, which was produced during normal operation at JET. The task should demonstrate the availability of the CECE process to handle and detritiate the water in terms of tritium enrichment and volume reduction. The operational program comprised the processing of purified tritiated water from JET, with a total volume of 180 l and an activity of 74 GBq. The paper will give an introduction to the TRENTA WDS facility and an overview of the operational procedure regarding tritiated water reduction. Data concerning required operation time, decontamination and enrichment performances and different operating procedures will be presented as well. Finally, a preliminary study on a technical implementation of processing the entire stock of JET

Pathways for Disposal of Commercially-Generated Tritiated Waste

Energy Technology Data Exchange (ETDEWEB)

Halverson, Nancy V. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Environmental Sciences and Biotechnology

2016-09-26

From a waste disposal standpoint, tritium is a major challenge. Because it behaves like hydrogen, tritium exchanges readily with hydrogen in the ground water and moves easily through the ground. Land disposal sites must control the tritium activity and mobility of incoming wastes to protect human health and the environment. Consequently, disposal of tritiated low-level wastes is highly regulated and disposal options are limited. The United States has had eight operating commercial facilities licensed for low-level radioactive waste disposal, only four of which are currently receiving waste. Each of these is licensed and regulated by its state. Only two of these sites accept waste from states outside of their specified regional compact. For waste streams that cannot be disposed directly at one of the four active commercial low-level waste disposal facilities, processing facilities offer various forms of tritiated low-level waste processing and treatment, and then transport and dispose of the residuals at a disposal facility. These processing facilities may remove and recycle tritium, reduce waste volume, solidify liquid waste, remove hazardous constituents, or perform a number of additional treatments. Waste brokers also offer many low-level and mixed waste management and transportation services. These services can be especially helpful for small-quantity tritiated-waste generators, such as universities, research institutions, medical facilities, and some industries. The information contained in this report covers general capabilities and requirements for the various disposal/processing facilities and brokerage companies, but is not considered exhaustive. Typically, each facility has extensive waste acceptance criteria and will require a generator to thoroughly characterize their wastes. Then a contractual agreement between the waste generator and the disposal/processing/broker entity must be in place before waste is accepted. Costs for tritiated waste

Pathways for Disposal of Commercially-Generated Tritiated Waste

International Nuclear Information System (INIS)

Halverson, Nancy V.

2016-01-01

From a waste disposal standpoint, tritium is a major challenge. Because it behaves like hydrogen, tritium exchanges readily with hydrogen in the ground water and moves easily through the ground. Land disposal sites must control the tritium activity and mobility of incoming wastes to protect human health and the environment. Consequently, disposal of tritiated low-level wastes is highly regulated and disposal options are limited. The United States has had eight operating commercial facilities licensed for low-level radioactive waste disposal, only four of which are currently receiving waste. Each of these is licensed and regulated by its state. Only two of these sites accept waste from states outside of their specified regional compact. For waste streams that cannot be disposed directly at one of the four active commercial low-level waste disposal facilities, processing facilities offer various forms of tritiated low-level waste processing and treatment, and then transport and dispose of the residuals at a disposal facility. These processing facilities may remove and recycle tritium, reduce waste volume, solidify liquid waste, remove hazardous constituents, or perform a number of additional treatments. Waste brokers also offer many low-level and mixed waste management and transportation services. These services can be especially helpful for small-quantity tritiated-waste generators, such as universities, research institutions, medical facilities, and some industries. The information contained in this report covers general capabilities and requirements for the various disposal/processing facilities and brokerage companies, but is not considered exhaustive. Typically, each facility has extensive waste acceptance criteria and will require a generator to thoroughly characterize their wastes. Then a contractual agreement between the waste generator and the disposal/processing/broker entity must be in place before waste is accepted. Costs for tritiated waste

Mass transfer in water-saturated concretes

International Nuclear Information System (INIS)

Atkinson, A.; Claisse, P.A.; Harris, A.W.; Nickerson, A.K.

1990-01-01

Cements and concretes are often considered as components of barriers for the containment of radioactive waste. The performance of such materials as mainly physical barriers to the transport of dissolved radionuclides depends on the mass transfer characteristics of the material. In particular the diffusion and sorption behavior of the radionuclides and the water permeability are important. These parameters also influence how the chemistry of the concrete is imposed on the repository. In addition, the transport of gas through concrete controls the way in which gases escape from the repository. Diffusion and gas transport have been measured in a variety of cementitious materials, covering both structural concretes and cementitious backfills; all possible repository construction materials. Measurements have been made using aqueous iodide, strontium and caesium ions and tritiated water as diffusants. The results show that the diffusion of tritiated water is more rapid than that of other species, whilst the transport of strontium and caesium is hindered by sorption; particularly in materials containing blast furnace slag. The transport of gas in these materials has been found to be very sensitive to the degree of water saturation and is extremely low in fully saturated structural concretes. Cementitious backfills have, nevertheless, been identified that have appreciable gas transport even when almost water saturated. The consequences of the results for the performance of cementitious barriers are discussed

Database dictionary for the results of groundwater tracer tests using tritiated water, conducted at the Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Thompson, B.K. [Univ. of Tennessee, Knoxville, TN (United States). Dept. of Civil Engineering; Huff, D.D. [Oak Ridge National Lab., TN (United States). Environmental Sciences Div.

1997-05-01

In 1977, the United States Geological Survey (USGS) conducted two tracer tests at the Oak Ridge National Laboratory (ORNL) using tritiated water to study the relative importance of bedding-plane openings on shallow groundwater flow. Through a cooperative agreement between the USGS and the US Department of Energy (DOE), the data were made available to researchers at the Oak Ridge National Laboratory (ORNL), who organized the data into a data management format. The results of these groundwater tracer tests have been compiled into a collection of four SAS data sets. This report documents these SAS data sets, including their structure, methodology, and content. The SAS data sets include information on precipitation, tritium, water levels, and well construction for wells at or near ORNL radioactive waste burial grounds 4, 5, and 6.

Influence of infiltrated water on the change of formation water and oil permeability of crude oil bearing rocks

Energy Technology Data Exchange (ETDEWEB)

Cubric, S

1970-09-01

A brief desription is given of the causes of permeability reduction of oil-bearing rocks, due to well damage during the drilling and well completion or when working over wells. The physical properties of 2-phase flow (crude oil-water) and the possibility of increasing the existing permeability of the formation, because of the water infiltrated from the well into the crude oil layer, are described in detail. Field examples show that there are such cases, and that the artificially increased existing permeability of water-bearing rocks can be reduced and even brought to normal, if the adjacent formation zone layer is treated with surfactants (e.g., Hyflo dissolved in crude oil).

Effects of prenatal exposure to low-dose β radiation from tritiated water on the neutrobehavior of mice

International Nuclear Information System (INIS)

Wang Bing; Zhou Xiangyan.

1995-01-01

Pregnant adult C57BL/6J mice, randomly assigned to 1 of 4 groups, 3 of them were irradiated with β-rays from tritiated water (HTO) by a single intraperitoneal injection on the 12.5th day of gestation. Their offspring received cumulative doses of 0, 5, 10 or 30 cGy in utero. Male pups were trained and examined using a set of behavioral tests that included avoidance acquisition and avoidance maintenance, open field test, hole-board dipping, a water maze, and a food labyrinth. Results were found for most parameters in the 10 and 30 cGy groups that differed significantly from results for the controls, indicating that the behavioral teratogenic effect of prenatal exposure to chronic β-ray radiation from HTO may be greater than the same dose of acute X- or γ-irradiation and that 10 cGy may be the lowest detectable dose level at which behavioral changes is detectable under the conditions used in this experiment. (author) 56 refs

Effects of prenatal exposure to low-dose {beta} radiation from tritiated water on the neutrobehavior of mice

Energy Technology Data Exchange (ETDEWEB)

Wang Bing [Tokyo Univ. (Japan). Faculty of Science; Zhou Xiangyan

1995-06-01

Pregnant adult C57BL/6J mice, randomly assigned to 1 of 4 groups, 3 of them were irradiated with {beta}-rays from tritiated water (HTO) by a single intraperitoneal injection on the 12.5th day of gestation. Their offspring received cumulative doses of 0, 5, 10 or 30 cGy in utero. Male pups were trained and examined using a set of behavioral tests that included avoidance acquisition and avoidance maintenance, open field test, hole-board dipping, a water maze, and a food labyrinth. Results were found for most parameters in the 10 and 30 cGy groups that differed significantly from results for the controls, indicating that the behavioral teratogenic effect of prenatal exposure to chronic {beta}-ray radiation from HTO may be greater than the same dose of acute X- or {gamma}-irradiation and that 10 cGy may be the lowest detectable dose level at which behavioral changes is detectable under the conditions used in this experiment. (author) 56 refs.

Excretion of organic and inorganic tritiated compounds in cow's milk after ingestion of tritium oxide

International Nuclear Information System (INIS)

Van den Hoek, J.; Gerber, G.B.; Kirchmann, R.

1980-01-01

The secretion in milk of tritium as water and organic molecules (casein and lipids) was studied after giving cows tritiated water for a period of 25 days. The data indicate that after a single application, tritium is mainly excreted as tritium water of rapid turnover. After continuous application, molecules with long half life, particularly lipids, become more important and may represent somewhat more than 4% of the total. (H.K.)

Radioimmunoanalysis of the immune response and tissue lipoperoxidation of rats for low doses contaminated with tritiated water

International Nuclear Information System (INIS)

Bejan, A.; Turcu, Gr.

1996-01-01

The paper presents the evaluation of the humoral immune response and liver and kidney lipoperoxidation on rats acutely and chronically contaminated with low doses of tritiated water (HTO). The contamination doses for both situations were 0.5 cSv, 5 cSv and 10 cSv. By humoral immune response analysis we mean the measurement, through a radioimmunoanalysis (RIA) method, of the two intrinsic parameters of an antiserum, that is, the mean antibodies concentration and the mean antibodies affinity constant. We followed the liver and kidney lipidic peroxidation through malondialdehyde (MDA) formation assayed by the thiobarbituric acid (TBA) reaction. The humoral immune response and lipoperoxidation have been compared with the response of an uncontaminated group by the Student t test. (author). 17 refs., 2 tabs

A new water permeability measurement method for unsaturated tight materials using saline solutions

International Nuclear Information System (INIS)

Malinsky, Laurent; Talandier, Jean

2012-01-01

Document available in extended abstract form only. Relative water permeability of material in a radioactive waste disposal is a key parameter to simulate and predict saturation state evolution. In this paper we present a new measurement method and the results obtained for Callovo-Oxfordian (Cox) clay-stone, host rock of the underground Andra laboratory at Bure (Meuse/Haute-Marne). Relative water permeability of such a low permeability rock as Cox clay-stone has been measured up to now by an indirect method. It consists in submitting a rock sample to successive relative humidity steps imposed by saline solutions. The transient mass variation during each step and the mass at hydric equilibrium are interpreted generally by using an inverse analysis method. The water relative permeability function of water saturation is derived from water diffusion coefficient evolution and water retention curve. The proposed new method consists in directly measuring the water flux across a flat cylindrical submitted to a relative humidity gradient. Two special cells have been developed. The tightness of the lateral sample surface is insured by crushing a polyurethane ring surrounding the sample set in an aluminium device placed over a Plexiglas vessel filled with a saline solution. One of the cells is designed to allow humidity measurement in the cell. These cells can also be used to measure the relative humidity produced by a saline solution or by an unsaturated material. During a permeability measurement, the cell with the sample to be tested is continuously weighted in a Plexiglas box in which a saline solution imposes a different relative humidity at the upper sample face. The experimental set-up is shown on Figure 1. The mean permeability of the sample is proportional to the rate of mass variation when steady state is reached. The result of one test is shown on Figure 2(a). Twenty four permeability measurements have been performed on four argillite samples of 15 mm in height and

Radioselective tritiation of acetanilide and para-substituted acetanilides

International Nuclear Information System (INIS)

Oohashi, K.; Nakamura, T.; Aoyama, Y.

1990-01-01

Acetanilide and para-substituted acetanilides were tritiated by heating with HTO in the presence of RhCl 3 .3H 2 O as a catalyst in an N,N-dimethylformamide solution at 105-107 deg C for 18 h. Under such conditions, tritium introduced into the anilide molecules was found at the adjacent ortho positions to the acetamido group with virtually 100% regioselectivity. The substituent effect on the rate of tritiation was observed. (author) 13 refs

Gas and water permeability of concrete for reactor buildings small specimens

International Nuclear Information System (INIS)

Mills, R.H.

1986-03-01

The effect on permeability of artifical aging by drying shrinkage and by freeze-thaw was determined by observing mass transfer of gas and water under a pressure gradient. It was found that damage due to freeze-thaw was negligible but that cracking around aggregate caused by drying shrinkage resulted in significantly increased permeability to both gas and water. The absence of freeze-thaw damage was attributed to self-dessication. Since the concrete was not exposed to an external source of water, the chemical reaction was sustained by consumption of mixing water. The resulting air voids were, apparently, sufficient to absorb expansive pressures due to ice formation. The response to lateral prestress was different for cracked and uncracked concrete. Although, in all cases, increased prestress resulted in reduced leakage, the effect was stronger in cracked concrete. Mean pore diameter as determined by gas diffusion was not, however, substantially affected because the leakage in cracked concrete remained very low. Reinforcing steel did not have a great influence on permeability of small specimens. Gas transmission through concrete was strongly influenced by moisture content. Free moisture constituted a barrier to gas flow, acting as a virtual solid. This is important since aging of concrete results in reduced free moisture. Ultrasonic pulse velocity appeared to vary with moisture content and porosity of concrete in the same way as gas permeability and gave promise of being effective for in-situ monitoring of concrete in reactor buildings

Estimation of tritiated water concentration in vegetables and milk around argentine nuclear power plants obtained from discharge sites and meteorological data

International Nuclear Information System (INIS)

Amado, Valeria A.; Lopez, Fabio O.; Sartori, Francisco M.

2009-01-01

The present work shows a methodology to assess the concentration of tritiated water in vegetation and milk. Calculations are depending on the release rate and the meteorological data of the nuclear installations. Methodology is based on existing models that had been modified taking in account available data and specific conditions in the vicinity of the nuclear power plants in Argentina. The predictions of the models are compared with the measurements of tritium concentrations in sampling of vegetables and milk occurred monthly during 2007, near of the plants. (author) [es

Cost effectiveness of detritiating water with resin columns

International Nuclear Information System (INIS)

Drake, R.H.; Williams, D.S.

1997-10-01

There are technologies in use for cleaning up concentrated tritiated process water. These are not cost effective for tritiated water with low concentrations of tritium. There are currently no cost-effective technologies for cleaning up low-tritium-concentration tritiated water, such as most tritiated groundwater, spent fuel storage basin water, or underground storage tank water. Resin removal of tritium from tritiated water at low concentrations (near the order of magnitude of drinking water standard maximums) is being tested on TA-SO (Los Alamos National Laboratory's Liquid Radioactive Waste Treatment Facility) waste streams. There are good theoretical and test indications that this may be a technologically effective means of removing tritium from tritiated water. Because of likely engineering design similarity, it is reasonable to anticipate that a resin column system's costs will be similar to some common commercial water treatment systems. Thus, the potential cost effectiveness of a resin treatment system offers hope for treating tritiated water at affordable costs. The TA-50 resin treatment cost projection of $18 per 1,000 gallons is within the same order of magnitude as cost data for typical commercial groundwater cleanup projects. The prospective Los Alamos National Laboratory (LANL) resin treatment system at $18 per 1,000 gallons appears to have a likely cost advantage of at least an order of magnitude over the competing, developmental, water detritiation technologies

Biological effects of tritiated water in low concentration of human lymphocyte chromosome

International Nuclear Information System (INIS)

Tanaka, K.; Kamada, N.; Sawaeda, S.

1992-01-01

This study was undertaken to investigate the dose-response relationship of tritiated water (HTO) for chromosome aberration in the human lymphocytes, at low dose in vitro exposure ranging from 0.1-1 Gy. The Relative Biological Effectiveness values of HTO with respect to 60 Co gamma ray at a dose rate of 2 cGy/min(15 mCi/ml), at low dose range for the induction of dicentric and centric ring chromosomes were 2.7 in lymphocytes. Also lymphocytes were chronically exposed to HTO for 67 to 80 hrs at different lower dose rates (0.5 and 0.02 cGy/min). There was a 77% decrease in the yields of dicentrics and centric rings, at the dose rate of 0.02cGy/min of HTO, presenting a clear dose rate effect of HTO. The RBE value of HTO relative to 137 Cs gamma ray was 2.0 at the dose rate of 0.02cGy/min(0.15mCi/ml). This suggests that a higher dose rate of HTO exposure has a higher risk and a decrease of RBE value at low dose rate. These results provide useful information for the assessment of health risks in humans specially exposed to low concentration of HTO. (author). 6 refs., 2 figs

Evaluation of the radiological risk resulting from road transportation of tritiated water

International Nuclear Information System (INIS)

Menossi, C.A.; Segado, R.; Reyes, R.

1983-01-01

A probability model for the evaluation of the individual radiological risk resulting from road transportation of tritiated water in 200-liter drums is presented. In order to evaluate such risk, an evaluation must be made of the probability for an individual to be involved in the consequences of a radiological transport accident, to incur a given dose and to suffer deleterious effects resulting from the dose incurred. With the purpose of quantifying the importance of accidents, a severity level classification was adopted as a function of the fraction of liquid volume spilled as a result of the accident. Considering the above-mentioned severity classification and the transported volume, the volume and the spill area are implied, while the soil characteristics are taken into account. By evaluating the spill characteristics, the average meteorological conditions in the area under analysis and the activity concentration of the transported liquid, the activity concentration values for tritium in air may be estimated, thus allowing calculation of the effective dose equivalent to be incurred by the individual who is most exposed to the consequences of an associated event. As a result of the summarized analysis above, a value of the individual risk per unit of activity concentration is obtained for tritium and for a given volume of transported liquid. 8 references

Studies on translocation of tritiated assimilates into potatoes and wheat grains

International Nuclear Information System (INIS)

Mueller, J.; Diabate, S.; Strack, S.; Raskob, W.

1993-01-01

Tritium released in the enviroment may be converted to organically bound tritium (OBT), mainly by photosynthesis in green leaves. Tritiated assimilates can be translocated from leaves to storage organs of crop plants. This should be considered in models calculating the dose due to the ingestion pathway. This paper describes experiments with wheat and potatoes, which have been designed to study the translocation of tritiated assimilates. Additionally, gas exchange measurements have been performed with the leaves of those plants. A model has been developed to estimate the generation of OBT and the translocation of tritiated assimilates into edible plant parts. (orig.) [de

Water permeability of acinar cell membranes in the isolated perfused rabbit mandibular salivary gland.

Science.gov (United States)

Steward, M C; Seo, Y; Rawlings, J M; Case, R M

1990-01-01

1. The diffusive water permeability of epithelial cell membranes in the perfused rabbit mandibular salivary gland was measured at 37 degrees C by a 1H nuclear magnetic resonance relaxation method using an extracellular relaxation reagent, gadolinium diethylenetriaminepentaacetic acid (Gd(DTPA)). 2. In glands perfused with a HEPES-buffered solution containing 10 mmol l-1 Gd(DTPA), the spin-lattice (T1) relaxation of the water protons showed two exponential components. The water compartment responsible for the slower component corresponded in magnitude to 71 +/- 5% of the wet weight of the gland, and was attributed to the exchangeable intracellular water of the acinar cells. 3. The rate constant for water efflux from the cells was estimated to be 4.1 +/- 0.1 s-1 which would be consistent with a diffusive membrane permeability (Pd) of approximately 3 x 10(-3) cm s-1. Stimulation with acetylcholine (10(-6) mol l-1) did not cause any detectable change in membrane water permeability. 4. Since the basolateral membrane probably provides the main pathway for water efflux, the osmotic water permeability of this barrier (expressed per gland) was estimated to be less than 6.2 cm3 s-1. This would be insufficient to account for the generation of a near-isosmotic fluid at the flow rates observed during secretion, and suggests that a substantial fraction of the flow of water occurs via a paracellular route. PMID:1966053

Data on thermal conductivity, water vapour permeability and water absorption of a cementitious mortar containing end-of-waste plastic aggregates

OpenAIRE

Di Maio, Luciano; Coppola, Bartolomeo; Courard, Luc; Michel, Frédéric; Incarnato, Loredana; Scarfato, Paola

2018-01-01

The data presented in this article are related to the research article entitled “Hygro-thermal and durability properties of a lightweight mortar made with foamed plastic waste aggregates ” (Coppola et al., 2018). This article focuses the attention on thermal conductivity, water vapour permeability and water absorption of a lightweight cementitious mortar containing foamed end-of-waste plastic aggregates, produced via foam extrusion process. Thermal conductivity, water vapour permeability ...

The effect of hot water injection on sandstone permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Haugwitz, Christian; Jacobsen, Peter Sally Munch

2014-01-01

Seasonal energy storage can be achieved by hot water injection in geothermal sandstone aquifers. We present an analysis of literature data in combination with new short-term flow through permeability experiments in order to address physical and physico-chemical mechanisms that can alter...

A comparison of experimental methods for measuring water permeability of porous building rocks

Directory of Open Access Journals (Sweden)

Galvan, S.

2014-09-01

Full Text Available This paper compares different experimental methods for measuring water permeability in 17 different porous building rocks. Both commercial apparatus and specially made designed permeameters are used for characterising intrinsic permeability and hydraulic conductivity, k, of rocks in the range of 10−12 to 10−4 m/s (~ 10−19−10−11 m2 or ~ 10−4−104 mD. We use both falling head and constant head permeameter methods including the triaxial and modified triaxial tests and a classical constant head permeameter. Results showed that for very low and low permeability samples (k−6 m/s, triaxial conditions were found the most accurate procedures and they provided similar or slightly lower permeability values than constant and falling head methods. The latter techniques were highly recommended for permeable and high permeable porous building materials. Water permeability values were also linked to effective porosity and interpreted in terms of interparticle and vugs porosity. Finally, some modifications in the apparatus and procedures were carried out in order to assess water permeability in soft materials, which involve the use of non-saturated samples.Se comparan diferentes métodos experimentales para la medida de la permeabilidad al agua en rocas porosas usadas como material de construcción. Se usaron diferentes permeabilímetros, (comerciales y desarrollados específicamente empleando los métodos triaxial, triaxial modificado, carga constante y carga variable. Se caracterizó la permeabilidad intrínseca y conductividad hidráulica, k, con valores que var.an desde 10−12 a 10−4 m/s (~ 10−19−10−11 m2 or ~ 10−4−104 mD. Para muestras poco y muy poco permeables el ensayo con célula triaxial fue el mas reproducible. Los ensayos de carga constante son muy recomendables para rocas porosas de construcción permeables y muy permeables. Además, se definen los parámetros experimentales más apropiados para caracterizar la

Survey of tritiated oil sources and handling practices

International Nuclear Information System (INIS)

Miller, J.M.

1994-08-01

Tritium interactions with oil sources (primarily associated with pumps) in tritium-handling facilities can lead to the incorporation of tritium in the oil and the production of tritiated hydrocarbons. This results in a source of radiological hazard and the need for special handling considerations during maintenance, decontamination, decommissioning and waste packaging and storage. The results of a general survey of tritiated-oil sources and their associated characteristics, handling practices, analysis techniques and waste treatment/storage methods are summarized here. Information was obtained from various tritium-handling laboratories, fusion devices, and CANDU plants. 38 refs., 1 fig

WATER VAPOUR PERMEABILITY PROPERTIES OF CELLULAR WOOD MATERIAL AND CONDENSATION RISK OF COMPOSITE PANEL WALLS

Directory of Open Access Journals (Sweden)

Janis IEJAVS

2016-09-01

Full Text Available Invention of light weight cellular wood material (CWM with a trade mark of Dendrolight is one of innovations in wood industry of the last decade. The aim of the research was to define the water vapour permeability properties of CWM and to analyse the condensation risk of various wall envelopes where solid wood cellular material is used. To determine the water vapour permeability of CWM, test samples were produced in the factory using routine production technology and tested according to the standard EN 12086:2014. Water vapour permeability factor (μ and other properties of six different configurations of CWM samples were determined. Using the experimental data the indicative influence of geometrical parameters such as lamella thickness, number of lamellas and material direction were investigated and evaluated. To study the condensation risk within the wall envelope containing CWM calculation method given in LVS EN ISO 13788:2012 was used. To ease the calculation process previously developed JavaScript calculation software that had only capability to calculate thermal transmittance was extended so that condensation risk in multi-layer composite walls can be analysed. Water vapour permeability factor in CWM is highly direction dependant. If parallel and perpendicular direction of CWM is compared the value of water vapour permeability factor can differentiate more than two times. Another significant factor for condensation risk analysis is overall thickness of CWM since it directly influences the equivalent air layer thickness. The influence of other factors such as lamella thickness, or groove depth is minor when water vapour permeability properties are compared. From the analysis of CWM performance in building envelope it can be concluded that uninsulated CWM panels used during winter months will pose the risk of condensation damage to structure, but the risk can be reduced or prevented if insulation layer is applied to the CWM panel wall

Dose from organically bound tritium after an acute tritiated water intake in humans

Energy Technology Data Exchange (ETDEWEB)

Trivedi, A; Richardson, R B; Galeriu, D [Atomic Energy of Canada Ltd., Chalk River, ON (Canada). Chalk River Nuclear Labs.

1995-10-01

We have analyzed the urinary excretion data from eight male workers following an acute intake of tritiated water (HTO) and assessed the dose contribution from organically bound tritium (OBT) in the body. The individuals affected increased their fluid intakes during the first month or more post-exposure, to accelerate the turnover of tritium in the body water for dose mitigation purposes. The volumes of cumulative 24 h urine samples were similar to Reference Man in the latter part of the study (100-300 d post-exposure). The workers` urine samples were analyzed for total tritium up to 300 d post-exposure. The results suggest that a measurement of the tritium activity per unit mass of organic matter in urine can provide an assessment of the specific activity of tritium in the organic fraction of the soft tissue, providing an equilibrium condition exists. A mathematical model is proposed to estimate the dose increase from the retained OBT by examining the kinetics of total tritium excretion in urine. The model accounts for the variable rates of fluid intake. The influence of measurement errors and the limited duration of the study (0-300 d post-exposure) on the OBT dose contribution was assessed through statistical analysis, while the role of direct OBT excretion in urine was estimated by using metabolic models. Based on the time series of tritium concentration in urine, the average dose increase to the workers from the metabolised OBT was calculated as 6.2 {+-} 1.3% of the HTO dose. 78 refs., 36 tabs., 11 figs.

Dose from organically bound tritium after an acute tritiated water intake in humans

International Nuclear Information System (INIS)

Trivedi, A.; Richardson, R.B.; Galeriu, D.

1995-10-01

We have analyzed the urinary excretion data from eight male workers following an acute intake of tritiated water (HTO) and assessed the dose contribution from organically bound tritium (OBT) in the body. The individuals affected increased their fluid intakes during the first month or more post-exposure, to accelerate the turnover of tritium in the body water for dose mitigation purposes. The volumes of cumulative 24 h urine samples were similar to Reference Man in the latter part of the study (100-300 d post-exposure). The workers' urine samples were analyzed for total tritium up to 300 d post-exposure. The results suggest that a measurement of the tritium activity per unit mass of organic matter in urine can provide an assessment of the specific activity of tritium in the organic fraction of the soft tissue, providing an equilibrium condition exists. A mathematical model is proposed to estimate the dose increase from the retained OBT by examining the kinetics of total tritium excretion in urine. The model accounts for the variable rates of fluid intake. The influence of measurement errors and the limited duration of the study (0-300 d post-exposure) on the OBT dose contribution was assessed through statistical analysis, while the role of direct OBT excretion in urine was estimated by using metabolic models. Based on the time series of tritium concentration in urine, the average dose increase to the workers from the metabolised OBT was calculated as 6.2 ± 1.3% of the HTO dose. 78 refs., 36 tabs., 11 figs

The application of neutron radiography to the measurement of the water-permeability of concrete

International Nuclear Information System (INIS)

Mo, Dawei; Zhang, Chaozong; Guo, Zhi-Ping; Liu, Yisi; An, Fulin; Mio, Qitian; Wang, Zhimin; Lian, Huizhen.

1988-01-01

The water-permeability of concrete is significant for dam, offshore platform and under-water basement of brindge etc. The traditional measuring method of permeability is the fixed pressure of water method in which the water-permeating process in a concreteblock cannot be measured continuously. Owing to the obvious difference of hydrogen content in the permeated regions of samples and the regions which have not been permeated. A combination of the neutron radiography and traditional method has been used to study continuously the whole process of water permeating. The combined method overcomes some shortages of the traditional methods and helps to gain more informations. (author)

An experimental study on the carcinogenic effect of tritiated water (HTO) in mice

International Nuclear Information System (INIS)

Yokoro, Kenjiro; Yamamoto, Osamu; Kamiya, Kenji; Fujii, Yoshiaki; Numoto, Michitaka; Kinomura, Aiko

1986-01-01

A large-scale study of the long-term carcinogenic effect of tritiated water (HTO) has been performed in mice. This is the interime report on the results as of May 8, 1986. A total of 391 seven-week-old (C57BL/6N x C3H/He) Fl mice were intraperitoneally given 1.0 Ci/0.2 ml of HTO (3.75, 7.5, 15, or 20 mCi/mouse), in either single or fractionated manner. The incidence of leukemia was approximately five times higher in the group receiving a fractionated administration of 20 mCi than that receiving the same amount in a single manner, as was the latent period shorter. The incidence of solid tumors, unlike leukemia, was evidently higher in the group receiving a single administration of 15 mCi than that receiving 3.75 mCi four times. The latent period also tended to be short in the former group. The groups with higher amounts of HTO had slightly higher incidence of multiple primaries. The ovary was the most common site of tumor. Expression of an oncogene, N-ras, was frequently observed in the case of leukemia, fibrosarcoma, and tumors of the thyroid, ovary, and lung. (Namekawa, K.)

Water permeabilities of pulverized fuel ash; Bifuntan sekitanbai no tosui tokusei

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Nagataki, S [Niigata University, Niigata (Japan); Hosoda, N [Kumagai Gumi Co. Ltd., Tokyo (Japan); Utsuki, T [The Coal Mining Research Center, Japan, Tokyo (Japan); Kubo, H [Obayashi Corp., Tokyo (Japan)

1996-09-01

It is intended to establish a technology to utilize coal ash in bulk to deal with its increasing production. In order to expand its use into earth engineering materials, two kinds of combustion ashes produced from dust coal burning power plants were used for studies using different kinds of tests. The tests were carried out on strength properties, water permeability, and characteristics of dissolving trace amounts of chemical constituents, with regard to addition effects of cement into compacted and slurry-state dust coal burned ashes. The derived findings may be summarized as follows: as the strength properties, the strength for both of the compacted and slurry-state ashes increases as the cement addition ratio is increased; growth of the strength due to the cement addition ratio and material age varies depending on the kinds of dust coal burned ash; comparison of strengths of the compacted and the slurry-state ashes indicates the strength of the latter ash is about one-third to quarter of that of the former ash; water permeability of the ashes decreases both in the compacted and slurry- state ashes as the cement addition ratio is increased; and the cement addition ratio gives greater impact to the water permeability than the density of the ashes. 28 figs., 5 tabs.

Tritiated imipramine binding sites are decreased in the frontal cortex of suicides

International Nuclear Information System (INIS)

Stanley, M.; Virgilio, J.; Gershon, S.

1982-01-01

Binding characteristics of tritiated imipramine were determined in the frontal cortex of suicides and well-matched controls. Maximal binding was significantly lower in brains from the suicides. This finding is consistent with reports of decreased tritiated imipramine binding in the platelets of patients diagnosed as having a major affective disorder

Transfer of tritium to prenatal and neonatal rats from their mothers exposed to tritiated compounds

Energy Technology Data Exchange (ETDEWEB)

Takeda, H.; Nishimura, Y.; Inaba, J. (National Inst. of Radiological Sciences, Chiba (Japan))

1994-01-01

The transfer of tritium through the placenta or milk was investigated to estimate the radiation dose to the fetus and newborn. Female rats at gestational stages or after delivery were exposed to tritium in the form of water, thymidine and lysine by a single oral administration and radioactivity in tissues including conceptuses (placenta, fetal membrane and fetus) and in the newborn was determined at various times after administration. In all cases of the investigated triated compounds, there was no significant difference between the tritium concentration in the fetus and that in the maternal tissues, suggesting that the placenta has no effect in preventing or accelerating the placental transfer of tritium. The time course of tritium concentration and tritium content in the fetus and newborn were, however, dependent on the chemical form of tritium and on the prenatal or neonatal stages at the time of ingestion. In general, the tritium concentration and tritium content after the ingestion of [sup 3]H-lysine were higher than that after the ingestion of tritiated water or [sup 3]H-thymidine. The result of dose estimation showed that [sup 3]H-lysine gave higher prenatal and neonatal doses than tritiated water or [sup 3]H-thymidine by a factor of 1.5 to 6.0. (author).

Water permeability evaluation of hollow cylindrical reinforced concrete structure by means of long-term water penetration test with pressure

International Nuclear Information System (INIS)

Fujiwara, Ai; Miura, Norihiko; Konishi, Kazuhiro; Tsuji, Yukikazu

2005-01-01

In order to evaluate initial permeability of large concrete structure, hollow cylindrical reinforced concrete structure, having 6 m in outer diameter, 6 m in height, 1 m in thickness, had been tested by means of 0.25 MPa of outside water pressure. As the results, although surface cracking and partial separation of joint had been observed at the inner side, no water permeation through concrete could be happened even after 5.5 years. After this test, concrete core specimen showed less water penetration within the depth of concrete cover of reinforcement. Thus it was verified that this concrete structure had very high water-tightness, and that the initial average water permeability was estimated to be about 1.6 x 10 -12 m/s. (author)

Tissue distribution of tritiated digoxin and quabain in mice

International Nuclear Information System (INIS)

Klopper, J.F.; Atkins, H.L.

1976-01-01

Tissue concentration of tritiated digoxin in human subjects appears to be selective in that after a single dose of the radioactive tracer a myocardial concentration of digoxin on an average 24 to 30 times higher than the serum concentration is reached. In patients studied 3.5 to 84 hours after administration of tritiated digoxin, the dose in the heart was found to vary between 1.95 to 4.83 percent. Should it be possible to label digoxin or another cardiac glycoside with a suitable gamma-emitting tracer, its use as a cardiac imaging agent should thus be feasible. This study was undertaken to determine the tissue distribution in mice of tritiated digoxin at various time intervals post injection; and to determine if these values showed any correlation to the previously determined human data. A preliminary study in mice using 3 H-digitoxin revealed no selective uptake in the heart with high uptakes in the liver and gut. Since ouabain has a more rapid clinical onset of action than digoxin, its tissue distribution was included in the study and compared to that of digoxin

Water and nonelectrolyte permeability of isolated rat hepatocytes

International Nuclear Information System (INIS)

Alpini, G.; Garrick, R.A.; Jones, M.J.; Nunes, R.; Tavoloni, N.

1986-01-01

We have measured the diffusive permeability coefficients of isolated rat hepatocytes to 3 H 2 O, [ 14 C]urea, [ 14 C]erythritol, [ 14 C]mannitol, [ 3 H]sucrose, and [ 3 H]inulin, employing a technique previously developed for erythrocytes (Redwood et al., J. Gen. Physiol 64:706-729, 1974). Diffusion coefficients for the tracer molecules were measured in packed hepatocytes, supernatant fluid, and intracellular medium (lysed hepatocytes) and were calculated assuming one-dimensional semi-infinite diffusion through a homogeneous medium. By applying the series-parallel pathway model, the following permeability coefficients (10(-5) cm/sec) for the hepatocyte plasma membrane were obtained. 3 H 2 O, 98.6 +/- 18.4; [ 14 C]urea, 18.2 +/- 5.3; [ 14 C]erythritol, 4.8 +/- 1.6; [ 14 C]mannitol, 3.1 +/- 1.4; [ 3 H]sucrose, 0; [ 3 H]inulin, 0. These results indicate that isolated rat hepatocytes are highly permeable to water and polar nonelectrolytes, when compared with other transporting epithelia. This relatively high cellular permeability is consistent with a model in which nonelectrolyte permeation is via an aqueous pathway of equivalent pore diameter of 8-12 A. The finding that [ 14 C]erythritol and [ 14 C]mannitol cross the hepatocyte plasma membrane indicates that these molecules enter the bile canaliculus through the transcellular route. Conversely, the failure of [ 3 H]sucrose and [ 3 H]inulin to permeate the hepatocyte in the isolated condition supports the concept that biliary entry of these large carbohydrates, at least that fraction which cannot be accounted for by a vesicular mechanism, must occur via the transjunctional shunt pathway

Environmental response nanosilica for reducing the pressure of water injection in ultra-low permeability reservoirs

Science.gov (United States)

Liu, Peisong; Niu, Liyong; Li, Xiaohong; Zhang, Zhijun

2017-12-01

The super-hydrophobic silica nanoparticles are applied to alter the wettability of rock surface from water-wet to oil-wet. The aim of this is to reduce injection pressure so as to enhance water injection efficiency in low permeability reservoirs. Therefore, a new type of environmentally responsive nanosilica (denote as ERS) is modified with organic compound containing hydrophobic groups and "pinning" groups by covalent bond and then covered with a layer of hydrophilic organic compound by chemical adsorption to achieve excellent water dispersibility. Resultant ERS is homogeneously dispersed in water with a size of about 4-8 nm like a micro-emulsion system and can be easily injected into the macro or nano channels of ultra-low permeability reservoirs. The hydrophobic nanosilica core can be released from the aqueous delivery system owing to its strong dependence on the environmental variation from normal condition to injection wells (such as pH and salinity). Then the exposed silica nanoparticles form a thin layer on the surface of narrow pore throat, leading to the wettability from water-wet to oil-wet. More importantly, the two rock cores with different permeability were surface treated with ERS dispersion with a concentration of 2 g/L, exhibit great reduce of water injection pressure by 57.4 and 39.6%, respectively, which shows great potential for exploitation of crude oil from ultra-low permeability reservoirs during water flooding. [Figure not available: see fulltext.

Water modelling studies of blockage with discrete permeabilities in an 11 pin geometry

International Nuclear Information System (INIS)

Robinson, D.P.

1977-06-01

A linear array of 11 pins, representing a radial section through a 325 pin bundle, has been used to investigate the effect of discrete permeabilities on the wake geometry behind a local blockage in water. Three series of experiments were performed in each of which a different position of the permeability was considered. The complex wake geometries, visualised by the injection of air, are shown to be controlled by the position of, and flowrate through the permeability. Good agreement is shown between the experimental flow patterns and predictions by SABRE 1. (author)

Process of preparing tritiated porous silicon

Science.gov (United States)

Tam, Shiu-Wing

1997-01-01

A process of preparing tritiated porous silicon in which porous silicon is equilibrated with a gaseous vapor containing HT/T.sub.2 gas in a diluent for a time sufficient for tritium in the gas phase to replace hydrogen present in the pore surfaces of the porous silicon.

Tritiated Dust Levitation by Beta Induced Static Charge

International Nuclear Information System (INIS)

Skinner, C.H.; Gentile, C.A.; Ciebiera, L.; Langish, S.

2003-01-01

Tritiated particles have been observed to spontaneously levitate under the influence of a static electric field. Tritium containing co-deposits were mechanically scraped from tiles that had been used in the Tokamak Fusion Test Reactor (TFTR) inner limiter during the deuterium-tritium campaign and were placed in a glass vial. On rubbing the plastic cap of the vial a remarkable ''fountain'' of particles was seen inside the vial. Particles from an unused tile or from a TFTR co-deposit formed during deuterium discharges did not exhibit this phenomenon. It appears that tritiated particles are more mobile than other particles and this should be considered in assessing tokamak accident scenarios and in occupational safety

Marked reduction in the number of platelet-tritiated imipramine binding sites in geriatric depression

International Nuclear Information System (INIS)

Nemeroff, C.B.; Knight, D.L.; Krishnan, R.R.; Slotkin, T.A.; Bissette, G.; Melville, M.L.; Blazer, D.G.

1988-01-01

The number (Bmax) and affinity (Kd) of platelet-tritiated imipramine binding sites was determined in young and middle-aged controls 50 years of age and younger (n = 25), elderly normal controls over 60 years of age (n = 18), patients who fulfilled DSM-III criteria for major depression who were under 50 years of age (n = 29), patients who fulfilled DSM-III criteria for major depression who were 60 years of age and older (n = 19), and patients who fulfilled both DSM-III criteria for primary degenerative dementia and National Institute of Neurological and Communicative Disorders and Stroke-Alzheimer's Disease and Related Disorders Association criteria for probable Alzheimer's disease (n = 13). Both groups of depressed patients (under 50 and over 60 years of age) exhibited significant reductions (decreases 42%) in the number of platelet-tritiated imipramine binding sites with no change in affinity, when compared with their age-matched controls. There was little overlap in Bmax values between the elderly depressed patients and their controls. The patients with probable Alzheimer's disease showed no alteration in platelet-tritiated imipramine binding. There was no statistically significant relationship between postdexamethasone plasma cortisol concentrations and tritiated imipramine binding. These results indicate that platelet-tritiated imipramine binding may have potential utility as a diagnostic adjunct in geriatric depression, and moreover that the reduction in the number of platelet-tritiated imipramine binding sites is not due to hypercortisolemia

Experimental study of heavy oil-water flow structure effects on relative permeabilities in a fracture filled with heavy oil

Energy Technology Data Exchange (ETDEWEB)

Shad, S.; Gates, I.D.; Maini, B.B. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering]|[Alberta Ingenuity Centre for In Situ Energy, Edmonton, AB (Canada)

2008-10-15

An experimental apparatus was used to investigate the flow of water in the presence of heavy oil within a smooth-walled fracture. Different flow patterns were investigated under a variety of flow conditions. Results of the experiments were used to determine the accuracy of VC, Corey, and Shad and Gates models designed to represent the behaviour of oil wet systems. The relative permeability concept was used to describe the behaviour of multiple phases flowing through porous media. A smooth-walled plexiglass Hele-Shaw cell was used to visualize oil and water flow. Changes in flow rates led to different flow regimes. The experiment demonstrated that water flowed co-currently in the form of droplets or slugs. Decreases in the oil flow rate enlarged the size of the water droplets as well as the velocity, until eventually the droplets coalesced and became water slugs. Droplet appearance or disappearance directly impacted the oil and water saturation levels. Changes in fluid saturation altered the pressure gradient. Darcy's law for the 2 liquid phases were used to calculate relative permeability curves. The study showed that at low water saturation, oil relative permeability reached as high as 2.5, while water relative permeability was lower than unity. In the presence of a continuous water channel, water drops formed in oil, and the velocity of the drops was lower than their velocity under a discontinuous water flow regime. It was concluded that the Shad and Gates model overestimated oil relative permeability and underestimated water relative permeability. 38 refs., 2 tabs., 9 figs.

Phenomenological study and modeling of tritium trapping in tritiated waste drums

International Nuclear Information System (INIS)

Le-Floch, Anais

2016-01-01

ITER (International Tokamak Experimental Reactor) is a fusion machine which should demonstrate scientific and technological feasibility of fusion energy by means of D-T fusion reaction. Therefore, most of the solid radioactive waste produced during operation and dismantling phase (around 34000 tons) will result not only from activation by 14 MeV neutrons, but also from contamination by tritium. One of the main issues in tritiated waste management is the confinement of tritium which presents a good ability to diffusion. One of the solutions is to trap the tritium directly in waste drums. In containers tritium is under gaseous form (HT and T_2), tritiated water vapor (HTO and T_2O) and organic bounded tritium species (OBT). as an hydrogen isotope, HT and T_2 trapping and conversion is possible thanks to a reaction with a mix of metal oxides MnO_2 and Ag_2O, which can be used for hydrogen hazards mitigation. an experimental study was conducted at the CEA on the study of tritium trapping by a mixture of 90% of manganese oxide and 10% of silver oxide. The tests showed that the addition of Pt and Pd catalysts did not improve the trapping capacity of the powder mixture, such as impregnation of the powder mixture when preparing the mixture, with solutions of KOH or NaOH. Crystal-chemical analysis revealed the formation of a mixed oxide in the preparation of powders, questioning the mechanisms previously established. Two new mechanisms have been proposed and a model on the trapping kinetics was presented. The results of modeling the competition between the trapping phenomenon and the diffusion of tritium through the wall of the waste package showed that the trapper decreased the value of the quantity of tritiated hydrogen degassed from the package. (author) [fr

Rapid increases in permeability and porosity of bentonite-sand mixtures due to alteration by water vapor

International Nuclear Information System (INIS)

Couture, R.A.

1984-01-01

Packed columns of canister packing material containing 25% bentonite and 75% quartz or basalt sand, were exposed to water vapor at temperatures up t 260 0 C. The permeabilities of the columns were subsequently measured after complete saturation with liquid water in a pressurized system. Exposure to water vapor caused irreversible increases in permeability by factors of up to 10 5 . After saturation with liquid water, the permeability was nearly independent of temperature. The increases in permeability were due to a large decrease in the ability of the bentonite to swell in water. Calculations suggest that swelling of bentonite altered at 250 0 C was not sufficient to fill the pore spaces. If the pore spaces are filled, the mixture will form an effective barrier against flow, diffusion, and transport of colloids. The results suggest that if bentonite-based canister packing material is exposed even briefly to water vapor at high temperatures in a high-level nuclear waste repository, its performance will be seriously impaired. The problem is less severe if the proportion of bentonite is high and the material is highly compacted. Previous results show significant degradation of bentonite by water vapor at temperatures as low as 150 0 C. This suggests that in some repositories, backfill in tunnels and drifts may also be affected. 9 references, 5 figures, 1 table

Electrochemical impedance spectrometry using 316L steel, hastelloy, maraging, Inconel 600, Elgiloy, carbon steel, TiN and NiCr. Simulation in tritiated water. 2 volumes

International Nuclear Information System (INIS)

Bellanger, G.

1994-03-01

Polarization and electrochemical impedance spectrometry curves are presented and discussed. These curves make it possible to ascertain the corrosion domains and to compare the slow and fast kinetics (voltammetry) of different stainless steel alloys. These corrosion kinetics, the actual or simulated tritiated water redox potentials, and the corrosion potentials provide a classification of the steels studied here: 316L, Hastelloy, Maraging, Inconel 600, Elgiloy, carbon steel and TiN and NiCr deposits. From the results it can be concluded that Hastelloy and Elgiloy have the best corrosion resistance. (author). 49 refs., 695 figs., tabs

Diffusion under water-saturated conditions in PFA/OPC-based structural concrete

International Nuclear Information System (INIS)

Harris, A.W.; Nickerson, A.K.

1990-05-01

A substantial proportion of the volume of the UK radioactive waste repository is likely to be composed of materials based on hydraulic cements. This includes the structural components, which are likely to be manufactured from concrete. The mass transport characteristics of dissolved species for a typical structural concrete, based on a mixture of pulverised fuel ash and ordinary Portland cement, have been measured in a water-saturated condition. Both the water permeability and the diffusion parameters (for caesium, strontium and iodide ion and tritiated water diffusion) are low compared to values obtained for other structural concretes. The intrinsic diffusion coefficients for iodide and caesium ions are in the range 2-5x10 -14 m 2 s -1 . There is no evidence of significant sorption of any of the diffusants studied. (author)

ECONOMICS ANALYSIS OF THE IMPLEMENTATION OF PERMEABLE REACTIVE BARRIERS FOR REMEDIATION OF CONTAMINATED GROUND WATER

Science.gov (United States)

This report presents an analysis of the cost of using permeable reactive barriers to remediate contaminated ground water. When possible, these costs are compared with the cost of pump-and-treat technology for similar situations. Permeable reactive barriers are no longer perceiv...

Plasticity of skin water permeability and skin thickness in the amphibious mangrove rivulus Kryptolebias marmoratus.

Science.gov (United States)

Heffell, Quentin; Turko, Andy J; Wright, Patricia A

2018-03-01

The skin of amphibious fishes is a multipurpose organ, important for gas and ion exchange and nitrogen excretion when fish are out of water (emersed). We tested the hypothesis that skin permeability is altered to maintain water balance through changes in water permeability and skin thickness during salinity acclimation and/or when fish emerse, using the euryhaline, amphibious fish Kryptolebias marmoratus as a model. We first recorded the behaviour of fish out of water to determine which part of the cutaneous surface was in contact with the substrate. Fish spent about 70% of their time on their ventral surface when out of water. Osmotic permeability of the skin was assessed in fish acclimated to 0.3 or 45‰ using 3 H 2 O fluxes in an in vitro micro-Ussing chamber setup. In freshwater-acclimated fish, 3 H 2 O influx across the skin was significantly higher compared to hypersaline-acclimated fish, with no significant changes in efflux. Prolonged emersion (7 days) resulted in an increase in skin 3 H 2 O influx, but not efflux in fish acclimated to a moist 45‰ substrate. In a separate experiment, dorsal epidermal skin thickness increased while the ventral dermis thickness decreased in fish emersed for over a week. However, there was no link between regional skin thickness and water flux in our experiments. Taken together, these findings suggest that K. marmoratus alter skin permeability to maximize water uptake while emersed in hypersaline conditions, adjustments that probably help them survive months of emersion during the dry season when drinking to replace water loss is not possible.

Characterization of erosion dust and tritiated products inside the jet vessel after the first tritium experiment

International Nuclear Information System (INIS)

Charuau, J.; Belot, Y.; Cetier, P.; Drezet, L.; Grivaud, L.

1992-01-01

An experiment was carried out to characterize the erosion products found in the JET vessel after the first tritium experiment. These products were analyzed for carbon, beryllium, Inconel metals and tritium. All these elements were present in airborne particles or deposited dust. The tritium was found as tritiated water vapour, and also strongly associated to the suspended or deposited particles. It was more abundant in fine than in coarse particles. The particulate tritium seems to be almost entirely 'insoluble' in a water solution

Water vapor permeabilities through polymers: diffusivities from experiments and simulations

International Nuclear Information System (INIS)

Seethamraju, Sindhu; Ramamurthy, Praveen Chandrashekarapura; Madras, Giridhar

2014-01-01

This study experimentally determines water vapor permeabilities, which are subsequently correlated with the diffusivities obtained from simulations. Molecular dynamics (MD) simulations were used for determining the diffusion of water vapor in various polymeric systems such as polyethylene, polypropylene, poly (vinyl alcohol), poly (vinyl acetate), poly (vinyl butyral), poly (vinylidene chloride), poly (vinyl chloride) and poly (methyl methacrylate). Cavity ring down spectroscopy (CRDS) based methodology has been used to determine the water vapor transmission rates. These values were then used to calculate the diffusion coefficients for water vapor through these polymers. A comparative analysis is provided for diffusivities calculated from CRDS and MD based results by correlating the free volumes. (paper)

Catalytic oxidation efficiencies for tritium and tritiated methane in a mature, industrial-scale decontamination system

International Nuclear Information System (INIS)

Mintz, J.M.; Gildea, P.D.

1981-01-01

Almost all tritium decontamination systems proposed for fusion facilities employ catalytic oxidation to water, followed by drying, to remove tritium and tritiated hydrocarbons from gas streams. One such large-scale system, the gas purification system (GPS), has been operating in the Tritium Research Laboratory (TRL) at Sandia National Laboratories, Livermore, CA, since October 1977. A series of experiments have recently been conducted there to assesss the current operating characteristics of the GPS catalyst. The experiments used tritium and tritiated methane and covered a range of temperatures, flow rates, and concentration levels. When contrasted with 1977 data, the results indicate that no measurable degradation of catalyst function had occurred. However, some reduction in active metal surface area, as indicated by B.E.T. surface area measurements (approx. 100 → 90m 2 /g) and AES scans (approx. 1.4 → 0.9 at. % Pt), had occurred. Kinetic rate coefficients were also derived and a rough temperature dependence obtained

Catalytic oxidation efficiencies for tritium and tritiated methane in a mature, industrial-scale decontamination system

International Nuclear Information System (INIS)

Mintz, J.M.; Gildea, P.D.

1980-10-01

Almost all tritium decontamination systems proposed for fusion facilities employ catalytic oxidation to water, followed by drying, to remove tritium and tritiated hydrocarbons from gas streams. One such large-scale system, the gas purification system (GPS), has been operating in the Tritium Research Laboratory (TRL) at Sandia National Laboratories, Livermore, CA, since October 1977. A series of experiments have recently been conducted there to assess the current operating characteristics of the GPS catalyst. The experiments used tritium and tritiated methane and covered a range of temperatures, flow rates, and concentration levels. When contrasted with 1977 data, the results indicate that no measurable degradation of catalyst function had occurred. However, some reduction in active metal surface area, as indicated by B.E.T. surface area measurements (approx. 100 → 90 m 2 /g) and AES scans (approx. 1.4 → 0.9 at% Pt), had occurred. Kinetic rate coefficients were also derived and a rough temperature dependence obtained

Preparation of a specifically tritiated locust adipokinetic hormone analog with full biological potency

Energy Technology Data Exchange (ETDEWEB)

Muramoto, K; Ramachandran, J; Moshitzky, P; Applebaum, S W [Hormone Research Laboratory and Department of Biochemistry and Biophysics, University of California, San Francisco, CA, USA and Department of Entomology, The Hebrew University of Jerusalem, Rehovot, Israel

1984-01-01

A synthetic peptide related to locus adipokinetic hormone (AKH) and shrimp red pigment concentrating hormone (RPCH) containing a tyrosine residue in place of phenylalanine was iodinated and the 3,5-diiodotyrosyl derivative was isolated by reverse phase HPLC. Catalytic dehalogenation of the diiodo derivative in the presence of tritium yielded the tritiated AKH analog which was isolated by gel filtration on Sephadex LH-20 and reverse phase HPLC. The tritiated peptide was formed to be identical to AKH in its ability to stimulate lipid release into the hemolymph of locusts in vivo where the diiodotryrosyl derivative was inactive. The specific radioactivity of the tritiated peptide was 57.2 Ci/mmol, or 99% of the theoretical value.

Chemical Composition and Water Permeability of Fruit and Leaf Cuticles of Olea europaea L.

Science.gov (United States)

Huang, Hua; Burghardt, Markus; Schuster, Ann-Christin; Leide, Jana; Lara, Isabel; Riederer, Markus

2017-10-11

The plant cuticle, protecting against uncontrolled water loss, covers olive (Olea europaea) fruits and leaves. The present study describes the organ-specific chemical composition of the cuticular waxes and the cutin and compares three developmental stages of fruits (green, turning, and black) with the leaf surface. Numerous organ-specific differences, such as the total coverage of cutin monomeric components (1034.4 μg cm -2 and 630.5 μg cm -2 ) and the cuticular waxes (201.6 μg cm -2 and 320.4 μg cm -2 ) among all three fruit stages and leaves, respectively, were detected. Water permeability as the main cuticular function was 5-fold lower in adaxial leaf cuticles (2.1 × 10 -5 m s -1 ) in comparison to all three fruit stages (9.5 × 10 -5 m s -1 ). The three fruit developmental stages have the same cuticular water permeability. It is hypothesized that a higher weighted average chain length of the acyclic cuticular components leads to a considerably lower permeability of the leaf as compared to the fruit cuticle.

Evaluation of an ambient air sampling system for tritium (as tritiated water vapor) using silica gel adsorbent columns

International Nuclear Information System (INIS)

Patton, G.W.; Cooper, A.T.; Tinker, M.R.

1995-08-01

Ambient air samples for tritium analysis (as the tritiated water vapor [HTO] content of atmospheric moisture) are collected for the Hanford Site Surface Environmental Surveillance Project (SESP) using the solid adsorbent silica gel. The silica gel has a moisture sensitive indicator which allows for visual observation of moisture movement through a column. Despite using an established method, some silica gel columns showed a complete change in the color indicator for summertime samples suggesting that breakthrough had occurred; thus a series of tests was conducted on the sampling system in an environmental chamber. The purpose of this study was to determine the maximum practical sampling volume and overall collection efficiency for water vapor collected on silica gel columns. Another purpose was to demonstrate the use of an impinger-based system to load water vapor onto silica gel columns to provide realistic analytical spikes and blanks for the Hanford Site SESP. Breakthrough volumes (V b ) were measured and the chromatographic efficiency (expressed as the number of theoretical plates [N]) was calculated for a range of environmental conditions. Tests involved visual observations of the change in the silica gel's color indicator as a moist air stream was drawn through the column, measurement of the amount of a tritium tracer retained and then recovered from the silica gel, and gravimetric analysis for silica gel columns exposed in the environmental chamber

Corrosion behavior of 316 L stainless steel simulated by studying the influence of the species produced in the radiolysis in tritiated aqueous solutions

International Nuclear Information System (INIS)

Bellanger, G.

1991-10-01

The corrosion of 316 L stainless steel in tritiated aqueous solutions was simulated by studying the influence of species produced or present in the radiolysis in these solutions. The species studied were nitrates, fluorides, nitrites, hydrogen peroxide and components of the steel, as well as the pH. The method used was voltammetry. The corroded or passivated surfaces were examined by scanning electron microscopy and the corrosion rates were determined by measuring the electrochemical impedance. The depletion of the component elements of the stainless steel at the surface was observed by X-ray fluorescence. From our results we propose methods to limit the corrosion in an industrial tritiated water installation by controlling the pH, the oxidation-reduction potential of the water and the voltage of the installation [fr

Forecast on Water Locking Damage of Low Permeable Reservoir with Quantum Neural Network

Science.gov (United States)

Zhao, Jingyuan; Sun, Yuxue; Feng, Fuping; Zhao, Fulei; Sui, Dianjie; Xu, Jianjun

2018-01-01

It is of great importance in oil-gas reservoir protection to timely and correctly forecast the water locking damage, the greatest damage for low permeable reservoir. An analysis is conducted on the production mechanism and various influence factors of water locking damage, based on which a quantum neuron is constructed based on the information processing manner of a biological neuron and the principle of quantum neural algorithm, besides, the quantum neural network model forecasting the water locking of the reservoir is established and related software is also made to forecast the water locking damage of the gas reservoir. This method has overcome the defects of grey correlation analysis that requires evaluation matrix analysis and complicated operation. According to the practice in Longxi Area of Daqing Oilfield, this method is characterized by fast operation, few system parameters and high accuracy rate (the general incidence rate may reach 90%), which can provide reliable support for the protection technique of low permeable reservoir.

Effects of low level prenatal beta-irradiation of tritiated water on postnatal behavior, learning and memory ability in mice

International Nuclear Information System (INIS)

Wang Bing; Zhou Xiangyan

1993-01-01

Pregnant adult C57 BL/6J strain mice, randomly assigned to 1 of 4 experimental groups, were irradiated with exponentially decreasing doses of tritium beta-rays but group 1 (used as a control) by single injection of tritiated water (HTO) at their 12.5 th day of gestation. Offsprings of male, received accumulative doses of 0, 0.5, 1.10 or 0.30 Gy in uterus were trained or examined on learning and memory ability or with behavioral tests. Significant dose-response relationships for alternations in those test were found due to exposure to 0.10 Gy or above. These results indicate that exposure to HTO during the fetal period in mice results in dose-dependent alteration in postnatal behavior, learning and memory ability. 0.05-0.10 Gy exposure may represent a threshold for the experimental conditions of this research using these parameters

Metabolic evaluation of skin absorption of tritiated formaldehyde in hairless rats

International Nuclear Information System (INIS)

Trivedi, A.

1993-11-01

Tritiated organics are present as trace impurities in tritium handling facilities. Tritiated formaldehyde has been detected in the atmosphere and gaseous effluents of tritium handling and storage sites. The ability of tritiated formaldehyde to diffuse through the skin is a possible route of intake. Since the metabolism of tritium through this mode of contamination is not currently established, experiments were performed in which tritiated formaldehyde was applied topically on the dorsal skin of hairless rats. These experiments demonstrated that tritium was assimilated and retained in the exposed skin as organically bound tritium (OBT). This retained OBT dominates tritium turnover in the body. OBT retention in the unexposed skin, liver, heart and kidneys was also observed. The loss of tritium from the animals showed that about 10% of the applied tritium was excreted in urine. It is assumed that the rest of the applied activity may have been lost through other excretory pathways, or may not have entered into the body. The biokinetics of tritium excretion is best described by a sum of three exponential functions. Most of the excreted tritium was in the form of OBT (90%) and results in the rapid clearing of OBT in the skin to urine and retention in other tissues. The evaluation of the dose-rate data showed that the dose-rate to exposed skin was almost a magnitude greater than the dose-rate to other organs. (author). 21 refs., 4 tabs., 4 figs

Metabolic evaluation of skin absorption of tritiated formaldehyde in hairless rats

Energy Technology Data Exchange (ETDEWEB)

Trivedi, A

1993-11-01

Tritiated organics are present as trace impurities in tritium handling facilities. Tritiated formaldehyde has been detected in the atmosphere and gaseous effluents of tritium handling and storage sites. The ability of tritiated formaldehyde to diffuse through the skin is a possible route of intake. Since the metabolism of tritium through this mode of contamination is not currently established, experiments were performed in which tritiated formaldehyde was applied topically on the dorsal skin of hairless rats. These experiments demonstrated that tritium was assimilated and retained in the exposed skin as organically bound tritium (OBT). This retained OBT dominates tritium turnover in the body. OBT retention in the unexposed skin, liver, heart and kidneys was also observed. The loss of tritium from the animals showed that about 10% of the applied tritium was excreted in urine. It is assumed that the rest of the applied activity may have been lost through other excretory pathways, or may not have entered into the body. The biokinetics of tritium excretion is best described by a sum of three exponential functions. Most of the excreted tritium was in the form of OBT (90%) and results in the rapid clearing of OBT in the skin to urine and retention in other tissues. The evaluation of the dose-rate data showed that the dose-rate to exposed skin was almost a magnitude greater than the dose-rate to other organs. (author). 21 refs., 4 tabs., 4 figs.

Effects of phase transformation of steam-water relative permeabilities

Energy Technology Data Exchange (ETDEWEB)

Verma, A.K.

1986-03-01

A combined theoretical and experimental study of steam-water relative permeabilities (RPs) was carried out. First, an experimental study of two-phase concurrent flow of steam and water was conducted and a set of RP curves was obtained. These curves were compared with semi-empirical and experimental results obtained by other investigators for two-phase, two-component flow (oil/gas; gas/water; gas/oil). It was found that while the wetting phase RPs were in good agreement, RPs for the steam phase were considerably higher than the non-wetting phase RPs in two-component systems. This enhancement of steam RP is attributed to phase transformation effects at the pore level in flow channels. The effects of phase transformation were studied theoretically. This study indicates that there are two separate mechanisms by which phase transformation affects RP curves: (1) Phase transformation is converging-diverging flow channels can cause an enhancement of steam phase RP. In a channel dominated by steam a fraction of the flowing steam condenses upstream from the constriction, depositing its latent heat of condensation. This heat is conducted through the solid grains around the pore throat, and evaporation takes place downstream from it. Therefore, for a given bulk flow quality; a smaller fraction of steam actually flows through the throat segments. This pore-level effect manifests itself as relative permeability enhancement on a macroscopic level; and (2) phase transformation along the interface of a stagnant phase and the phase flowing around it controls the irreducible phase saturation. Therefore, the irreducible phase saturation in steam-water flow will depend, among other factors, on the boundary conditions of the flow.

Relative Permeability of Fractured Rock

Energy Technology Data Exchange (ETDEWEB)

Mark D. Habana

2002-06-30

Contemporary understanding of multiphase flow through fractures is limited. Different studies using synthetic fractures and various fluids have yielded different relative permeability-saturation relations. This study aimed to extend the understanding of multiphase flow by conducting nitrogen-water relative permeability experiments on a naturally-fractured rock from The Geysers geothermal field. The steady-state approach was used. However, steady state was achieved only at the endpoint saturations. Several difficulties were encountered that are attributed to phase interference and changes in fracture aperture and surface roughness, along with fracture propagation/initiation. Absolute permeabilities were determined using nitrogen and water. The permeability values obtained change with the number of load cycles. Determining the absolute permeability of a core is especially important in a fractured rock. The rock may change as asperities are destroyed and fractures propagate or st rain harden as the net stresses vary. Pressure spikes occurred in water a solute permeability experiments. Conceptual models of an elastic fracture network can explain the pressure spike behavior. At the endpoint saturations the water relative permeabilities obtained are much less than the nitrogen gas relative permeabilities. Saturations were determined by weighing and by resistivity calculations. The resistivity-saturation relationship developed for the core gave saturation values that differ by 5% from the value determined by weighing. Further work is required to complete the relative permeability curve. The steady-state experimental approach encountered difficulties due to phase interference and fracture change. Steady state may not be reached until an impractical length of time. Thus, unsteady-state methods should be pursued. In unsteady-state experiments the challenge will be in quantifying rock fracture change in addition to fluid flow changes.

Preparation of tritiated polystyrene and its application in radio luminescent paints

International Nuclear Information System (INIS)

Ravi, S.; Mathewy, K.M.; Seshadri, N.K.; Subramanian, T.K.

2001-01-01

Beta radiation emanating from tritiated polystyrene in close proximity with copper activated zinc sulphide phosphor will provide self-sustained light sources and are used for nocturnal illumination of watches and clocks, product advertisements, telephone numbers, exit signs etc. Phenylacetylene was partially reduced in diethyl ether medium with tritium using 5% Pd/C poisoned with quinoline to give styrene. Styrene formed was polymerised to polystyrene by subjecting it to irradiation with γ-radiation (20 mega rad dose). Copper activated zinc sulphide phosphor was coated with tritiated polystyrene to give self-sustained light sources. (author)

Modelling water vapour permeability through atomic layer deposition coated photovoltaic barrier defects

Energy Technology Data Exchange (ETDEWEB)

Elrawemi, Mohamed, E-mail: Mohamed.elrawemi@hud.ac.uk [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom); Blunt, Liam; Fleming, Leigh [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom); Bird, David, E-mail: David.Bird@uk-cpi.com [Centre for Process Innovation Limited, Sedgefield, County Durham (United Kingdom); Robbins, David [Centre for Process Innovation Limited, Sedgefield, County Durham (United Kingdom); Sweeney, Francis [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom)

2014-11-03

Transparent barrier films such as Al{sub 2}O{sub 3} used for prevention of oxygen and/or water vapour permeation are the subject of increasing research interest when used for the encapsulation of flexible photovoltaic modules. However, the existence of micro-scale defects in the barrier surface topography has been shown to have the potential to facilitate water vapour ingress, thereby reducing cell efficiency and causing internal electrical shorts. Previous work has shown that small defects (≤ 3 μm lateral dimension) were less significant in determining water vapour ingress. In contrast, larger defects (≥ 3 μm lateral dimension) seem to be more detrimental to the barrier functionality. Experimental results based on surface topography segmentation analysis and a model presented in this paper will be used to test the hypothesis that the major contributing defects to water vapour transmission rate are small numbers of large defects. The model highlighted in this study has the potential to be used for gaining a better understanding of photovoltaic module efficiency and performance. - Highlights: • A model of water vapour permeation through barrier defects is presented. • The effect of the defects on the water vapour permeability is investigated. • Defect density correlates with water vapour permeability. • Large defects may dominate the permeation properties of the barrier film.

The diffusion permeability to water of the rat blood-brain barrier

DEFF Research Database (Denmark)

Bolwig, T G; Lassen, N A

1975-01-01

The diffusion permeability to water of the rat blood-brain-barrier (BBB) was studied. Preliminary data obtained with the Oldendorf tissue uptake method (Oldendorf 1970) in seizure experiments suggested that the transfer from blood to brain of labelled water is diffusion-limited. More definite...... passage increased from 0.26 to 0.67 when the arterial carbon dioxide tension was changed from 15 to 85 mm Hg, a change increasing the cerebral blood flow about sixfold. This finding suggests that water does not pass the blood-brain barrier as freely as lipophilic gases....

Capture and isotopic exchange method for water and hydrogen isotopes on zeolite catalysts up to technical scale for pre-study of processing highly tritiated water

Energy Technology Data Exchange (ETDEWEB)

Michling, R.; Braun, A.; Cristescu, I.; Dittrich, H.; Gramlich, N.; Lohr, N. [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany); Glugla, M.; Shu, W.; Willms, S. [ITER Organization, Saint-Paul-lez-Durance (France)

2015-03-15

Highly tritiated water (HTW) may be generated at ITER by various processes and, due to the excessive radio toxicity, the self-radiolysis and the exceedingly corrosive property of HTW, a potential hazard is associated with its storage and process. Therefore, the capture and exchange method for HTW utilizing Molecular Sieve Beds (MSB) was investigated in view of adsorption capacity, isotopic exchange performance and process parameters. For the MSB, different types of zeolite were selected. All zeolite materials were additionally coated with platinum. The following work comprised the selection of the most efficient zeolite candidate based on detailed parametric studies during the H{sub 2}/D{sub 2}O laboratory scale exchange experiments (about 25 g zeolite per bed) at the Tritium Laboratory Karlsruhe (TLK). For the zeolite, characterization analytical techniques such as Infrared Spectroscopy, Thermogravimetry and online mass spectrometry were implemented. Followed by further investigation of the selected zeolite catalyst under full technical operation, a MSB (about 22 kg zeolite) was processed with hydrogen flow rates up to 60 mol*h{sup -1} and deuterated water loads up to 1.6 kg in view of later ITER processing of arising HTW. (authors)

Experimental study and phenomenological modeling of the hydrolysis of tritiated sodium: influence of experimental conditions on the tritium distribution in the effluents

International Nuclear Information System (INIS)

Chassery, Aurelien

2014-01-01

Within the framework of the decommissioning of fast reactors, several processes are under investigation regarding sodium disposal. One of them rests on the implementation of the sodium-water reaction (SWR), in a controlled and progressive way, to remove residual sodium containing impurities such as sodium hydrides, sodium oxides and tritiated sodium hydrides. Such a hydrolysis releases some amount of energy and produces a liquid effluent, composed of a solution of soda, and a gaseous effluent, composed of hydrogen, steam and an inert gas. The tritium, originally into the sodium as a soluble (T - ) or precipitate form (NaT), will be distributed between the liquid and gaseous effluent, and according to two chemical forms, the tritium hydride HT and the tritiated water HTO. HTO being 10,000 times more radio-toxic than HT, a precise knowledge of the mechanisms governing the distribution of tritium is necessary in order to estimate the exhaust gas releases and design the process needed to treat the off-gas before its release into the environment. An experimental study has been carried out in order to determine precisely the phenomena involved in the hydrolysis. The influence of the experimental conditions on the tritium distribution has been tested. The results of this study leaded to a phenomenological description of the tritiated sodium hydrolysis that will help to predict the composition of the effluents, regarding tritium. (author) [fr

Classification of cassava starch films by physicochemical properties and water vapor permeability quantification by FTIR and PLS.

Science.gov (United States)

Henrique, C M; Teófilo, R F; Sabino, L; Ferreira, M M C; Cereda, M P

2007-05-01

Cassava starches are widely used in the production of biodegradable films, but their resistance to humidity migration is very low. In this work, commercial cassava starch films were studied and classified according to their physicochemical properties. A nondestructive method for water vapor permeability determination, which combines with infrared spectroscopy and multivariate calibration, is also presented. The following commercial cassava starches were studied: pregelatinized (amidomax 3550), carboxymethylated starch (CMA) of low and high viscosities, and esterified starches. To make the films, 2 different starch concentrations were evaluated, consisting of water suspensions with 3% and 5% starch. The filmogenic solutions were dried and characterized for their thickness, grammage, water vapor permeability, water activity, tensile strength (deformation force), water solubility, and puncture strength (deformation). The minimum thicknesses were 0.5 to 0.6 mm in pregelatinized starch films. The results were treated by means of the following chemometric methods: principal component analysis (PCA) and partial least squares (PLS) regression. PCA analysis on the physicochemical properties of the films showed that the differences in concentration of the dried material (3% and 5% starch) and also in the type of starch modification were mainly related to the following properties: permeability, solubility, and thickness. IR spectra collected in the region of 4000 to 600 cm(-1) were used to build a PLS model with good predictive power for water vapor permeability determination, with mean relative errors of 10.0% for cross-validation and 7.8% for the prediction set.

Effects of prenatal exposure to low dose beta radiation from tritiated water on postnatal growth and neurobehavior of mice

International Nuclear Information System (INIS)

Gao Weimin; Zhou Xiangyan

1998-01-01

Pregnant adult C57BL/6J mice were randomly assigned to 4 groups and 3 of them were irradiated with beta-rays from tritiated water (HTO) by a single intraperitoneal injection on the 12.5 th day of gestation. Their offsprings received cumulative dose of 0.036, 0.071 and 0.213 Gy, respectively. Offspring of mice were observed for postnatal growth (body weight), the appearance of four physiologic makers (eye opening, pinna detachment, testes decent, vaginal opening), the age of acquisition of two reflexes (cloff avoidance, air righting) and sensuous functions (auditory startle, pain threshold), movement and coordination functions and activity (pivoting, foot splay, continuous corridor activity), and learning and memory (electric avoidance reflex in Y-maze, conditioning reflex). It was found that results for the parameters in 0.036 or 0.071 Gy group were differed significantly from those for the controls, and for most parameters, a dose dependent effect was found

Permeability measuremens of brazilian Eucalyptus

Directory of Open Access Journals (Sweden)

Marcio Rogério da Silva

2010-09-01

Full Text Available The permeability of Brazilian Eucalyptus grandis and Eucalyptus citriodora wood was measured in a custom build gas analysis chamber in order to determine which species could be successfully treated with preservatives. Liquid permeability was tested using an emulsion of Neen oil and a control of distillated water. Air was used to test the gas phase permeability. For both Eucalyptus grandis and Eucalyptus citriodora, the longitudinal permeability of gas was shown to be about twice as great as the liquid phase permeability. No radial permeability was observed for either wood. The permeability of air and water through the sapwood of Eucalyptus grandis was greater than that through the sapwood of Eucalyptus citriodora. The permeability of neen oil preservative through the sapwood of Eucalyptus grandis was also greater than through the sapwood of E. Citradora, but the difference was not statistically significant. Scanning Electron Microscopy images showed that the distribution and obstruction in the vessels could be correlated with observed permeability properties. Irrespective of the causes of differences in permeability between the species, the fluid phase flux through the sapwood of both species was significant, indicating that both Eucalyptus grandis and Eucalyptus citriodora could be successfully treated with wood preservative.

ETHEL's systems and facilities for safe management of tritiated wastes

International Nuclear Information System (INIS)

Mannone, F.; Dworschak, H.; Vassallo, G.

1992-01-01

The European Tritium Handling Experimental Laboratory (ETHEL) is a new tritium facility at the Commission of the European Community's Joint Research Centre, Ispra Site. The laboratory, destined to handle multigram amounts of tritium for safety related R and D purposes, is foreseen to start radioactive operations in late 1992. The general operation and maintenance of laboratory systems and future experiments will generate tritiated wastes in gaseous, liquid and solid forms. The management of such wastes under safe working conditions is a stringent laboratory requirement aimed at minimizing the risk of unacceptable tritium exposures to workers and the general public. This paper describes the main systems and facilities installed in ETHEL for the safe management of tritiated wastes

Sub-core permeability and relative permeability characterization with Positron Emission Tomography

Science.gov (United States)

Zahasky, C.; Benson, S. M.

2017-12-01

This study utilizes preclinical micro-Positron Emission Tomography (PET) to image and quantify the transport behavior of pulses of a conservative aqueous radiotracer injected during single and multiphase flow experiments in a Berea sandstone core with axial parallel bedding heterogeneity. The core is discretized into streamtubes, and using the micro-PET data, expressions are derived from spatial moment analysis for calculating sub-core scale tracer flux and pore water velocity. Using the flux and velocity data, it is then possible to calculate porosity and saturation from volumetric flux balance, and calculate permeability and water relative permeability from Darcy's law. Full 3D simulations are then constructed based on this core characterization. Simulation results are compared with experimental results in order to test the assumptions of the simple streamtube model. Errors and limitations of this analysis will be discussed. These new methods of imaging and sub-core permeability and relative permeability measurements enable experimental quantification of transport behavior across scales.

Permeability of fissured rock - an experimental study with special regard to the water injection test

International Nuclear Information System (INIS)

Schneider, H.J.

1987-01-01

The permeability to water of fissured rock is one of the most important design parameters for many underground projects, such as, e.g. the final deposition of radioactive waste. Because the conventional water injection test according to LUGEON for the calculation of permeability to water is associated with a high degree of uncertainty, new test equipment was developed. This equipment works on the principle of the water injection tracer test and multi-level measurements, enabling detailed measurement of the flow process at injection site and in the rock. The tests were carried out in Bunter sandstone and granite. The LUGEON test concept was varied in short-term and long-term tests at identical geological boundary conditions, and with test control at constant pressure on the one hand and at constant injection volume on the other. The test results show that non-steady-state flow occurs with short injection times, whereby the range is limited to the local rock at injection site. An increasing in injection time can lead to an increase in range by a number of factors as well as to steady-state flow conditions. The permeability of the rock types investigated is inhomgeneous and anistropic as a result of the fissured structure. (orig./HP) With 114 figs., 4 tabs [de

A study of lipogenesis de novo: kinetics of tritiated water 3H incorporation in vivo into fatty acids and total lipids of the liver, plasma, adipose tissue and carcass of the male rat

International Nuclear Information System (INIS)

Gandemer, Gille; Pascal, Gerard; Durand, Georges

1980-01-01

Tritiated water 3 H, injected by intraperitoneal route into 7-week old male Rats, was incorporated into lipids synthesized de novo. The Rats were killed 0, 3, 7, 10, 15, 30, 60 and 120 min. after tracer injection. The results show that an optimal interval of about 10 min. between tracer injection and animal sacrifice was necessary to obtain a correct estimate of lipogenesis de novo by avoiding intertissue exchanges [fr

Highly permeable polymeric membranes based on the incorporation of the functional water channel protein Aquaporin Z

Science.gov (United States)

Kumar, Manish; Grzelakowski, Mariusz; Zilles, Julie; Clark, Mark; Meier, Wolfgang

2007-01-01

The permeability and solute transport characteristics of amphiphilic triblock-polymer vesicles containing the bacterial water-channel protein Aquaporin Z (AqpZ) were investigated. The vesicles were made of a block copolymer with symmetric poly-(2-methyloxazoline)-poly-(dimethylsiloxane)-poly-(2-methyloxazoline) (PMOXA15-PDMS110-PMOXA15) repeat units. Light-scattering measurements on pure polymer vesicles subject to an outwardly directed salt gradient in a stopped-flow apparatus indicated that the polymer vesicles were highly impermeable. However, a large enhancement in water productivity (permeability per unit driving force) of up to ≈800 times that of pure polymer was observed when AqpZ was incorporated. The activation energy (Ea) of water transport for the protein-polymer vesicles (3.4 kcal/mol) corresponded to that reported for water-channel-mediated water transport in lipid membranes. The solute reflection coefficients of glucose, glycerol, salt, and urea were also calculated, and indicated that these solutes are completely rejected. The productivity of AqpZ-incorporated polymer membranes was at least an order of magnitude larger than values for existing salt-rejecting polymeric membranes. The approach followed here may lead to more productive and sustainable water treatment membranes, whereas the variable levels of permeability obtained with different concentrations of AqpZ may provide a key property for drug delivery applications. PMID:18077364

Tritium NMR in the analysis of tritiated compounds

International Nuclear Information System (INIS)

Kaspersen, F.M.; Funke, C.W.; Vader, Jan; Wagenaars, G.N.

1993-01-01

An overview is given of the possibilities of 3 H NMR in the characterisation of 3 H-labelled compounds. This technique gives information on the identity of the tritiated compounds, the position of the tritium, the distribution of the label and even the radiochemical purity of the labelled products. (author)

The Dependence of Water Permeability in Quartz Sand on Gas Hydrate Saturation in the Pore Space

Science.gov (United States)

Kossel, E.; Deusner, C.; Bigalke, N.; Haeckel, M.

2018-02-01

Transport of fluids in gas hydrate bearing sediments is largely defined by the reduction of the permeability due to gas hydrate crystals in the pore space. Although the exact knowledge of the permeability behavior as a function of gas hydrate saturation is of crucial importance, state-of-the-art simulation codes for gas production scenarios use theoretically derived permeability equations that are hardly backed by experimental data. The reason for the insufficient validation of the model equations is the difficulty to create gas hydrate bearing sediments that have undergone formation mechanisms equivalent to the natural process and that have well-defined gas hydrate saturations. We formed methane hydrates in quartz sand from a methane-saturated aqueous solution and used magnetic resonance imaging to obtain time-resolved, three-dimensional maps of the gas hydrate saturation distribution. These maps were fed into 3-D finite element method simulations of the water flow. In our simulations, we tested the five most well-known permeability equations. All of the suitable permeability equations include the term (1-SH)n, where SH is the gas hydrate saturation and n is a parameter that needs to be constrained. The most basic equation describing the permeability behavior of water flow through gas hydrate bearing sand is k = k0 (1-SH)n. In our experiments, n was determined to be 11.4 (±0.3). Results from this study can be directly applied to bulk flow analysis under the assumption of homogeneous gas hydrate saturation and can be further used to derive effective permeability models for heterogeneous gas hydrate distributions at different scales.

Effects of water activity and low molecular weight humectants on skin permeability and hydration dynamics - a double-blind, randomized and controlled study.

Science.gov (United States)

Albèr, C; Buraczewska-Norin, I; Kocherbitov, V; Saleem, S; Lodén, M; Engblom, J

2014-10-01

The mammalian skin is a barrier that effectively separates the water-rich interior of the body from the normally dryer exterior. Changes in the external conditions, for example ambient humidity, have been shown to affect the skin barrier properties. The prime objective of this study was to evaluate the effect of water activity of a topical formulation on skin hydration and permeability. A second objective was to gain more understanding on how two commonly used humectants, urea and glycerol, affect skin barrier function in vivo. Simple aqueous formulations were applied under occlusion to the volar forearm of healthy volunteers. Following 4-h exposure, skin water loss (by transepidermal water loss measurements), skin hydration (by Corneometry) and skin permeability (by time to vasodilation due to benzyl nicotinate exposure) were monitored. The results demonstrate that a relatively small change in the water activity of a topical formulation is sufficient to induce considerable effects on stratum corneum hydration and permeability to exogenous substances. Exposing the skin to high water activity leads to increased skin hydration and also increased permeability. Furthermore, urea and glycerol promote skin hydration and permeability even at reduced water activity of the applied formulation. These results highlight the importance of considering the water activity in topically applied formulations and the potential benefit of using humectants. The results may impact formulation optimization in how to facilitate skin hydration and to modify skin permeability by temporarily open and close the skin barrier. © 2014 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Water and vapor permeability at different temperatures of poly (3-Hydroxybutyrate dense membranes

Directory of Open Access Journals (Sweden)

Luiz H. Poley

2005-03-01

Full Text Available Polyhydroxyalkanoates (PHAs are polymers produced from renewable resources with biodegradability and biocompatibility, being therefore attractive for medical and pharmaceutical purposes. Poly (3-hydroxybutyrate (PHB is the most important polymer of this family by considering the biotechnology process of its synthesis. In the present study, dense films of PHB were prepared by casting from chloroform solutions (1% m/m. Permeability studies with water, methanol, ethanol and n-propanol were performed using the gravimetric method at different temperatures (from 50 ºC to 65 ºC. Results provide new data on permeability coefficients of PHB membranes.

The metabolism of tritiated oleic acid in the rat. A radiological protection study

International Nuclear Information System (INIS)

Jeanmaire, Lucien; Vernois, Yvette; Nazard, Raymonde.

1979-04-01

The metabolism of 3 H-labelled oleic acid has been studied in the rat during 600 days. The results of urinary and fecal excretions, of the retention of the total and fixed activities in 25 tissues or organs and the cumulative activity from day 4 to 616 are discussed. Oleic acid is more widely spread than other labelled molecules studied previously both as regard excretion or retention. During the first 4 days one can grossly admit that half the activity is fixed to water and half is stored in the adipose tissues which it leaves quickly first, then more slowly with a half-life of 200 days about. For some ten tissues, the cumulative activity due to the fixed fraction exceeds the cumulative activity due to tritiated water obtained by metabolism of oleic acid [fr

Subsurface imaging of water electrical conductivity, hydraulic permeability and lithology at contaminated sites by induced polarization

Science.gov (United States)

Maurya, P. K.; Balbarini, N.; Møller, I.; Rønde, V.; Christiansen, A. V.; Bjerg, P. L.; Auken, E.; Fiandaca, G.

2018-05-01

At contaminated sites, knowledge about geology and hydraulic properties of the subsurface and extent of the contamination is needed for assessing the risk and for designing potential site remediation. In this study, we have developed a new approach for characterizing contaminated sites through time-domain spectral induced polarization. The new approach is based on: (1) spectral inversion of the induced polarization data through a reparametrization of the Cole-Cole model, which disentangles the electrolytic bulk conductivity from the surface conductivity for delineating the contamination plume; (2) estimation of hydraulic permeability directly from the inverted parameters using a laboratory-derived empirical equation without any calibration; (3) the use of the geophysical imaging results for supporting the geological modelling and planning of drilling campaigns. The new approach was tested on a data set from the Grindsted stream (Denmark), where contaminated groundwater from a factory site discharges to the stream. Two overlapping areas were covered with seven parallel 2-D profiles each, one large area of 410 m × 90 m (5 m electrode spacing) and one detailed area of 126 m × 42 m (2 m electrode spacing). The geophysical results were complemented and validated by an extensive set of hydrologic and geologic information, including 94 estimates of hydraulic permeability obtained from slug tests and grain size analyses, 89 measurements of water electrical conductivity in groundwater, and four geological logs. On average the IP-derived and measured permeability values agreed within one order of magnitude, except for those close to boundaries between lithological layers (e.g. between sand and clay), where mismatches occurred due to the lack of vertical resolution in the geophysical imaging. An average formation factor was estimated from the correlation between the imaged bulk conductivity values and the water conductivity values measured in groundwater, in order to

A drainage data-based calculation method for coalbed permeability

International Nuclear Information System (INIS)

Lai, Feng-peng; Li, Zhi-ping; Fu, Ying-kun; Yang, Zhi-hao

2013-01-01

This paper establishes a drainage data-based calculation method for coalbed permeability. The method combines material balance and production equations. We use a material balance equation to derive the average pressure of the coalbed in the production process. The dimensionless water production index is introduced into the production equation for the water production stage. In the subsequent stage, which uses both gas and water, the gas and water production ratio is introduced to eliminate the effect of flush-flow radius, skin factor, and other uncertain factors in the calculation of coalbed methane permeability. The relationship between permeability and surface cumulative liquid production can be described as a single-variable cubic equation by derivation. The trend shows that the permeability initially declines and then increases after ten wells in the southern Qinshui coalbed methane field. The results show an exponential relationship between permeability and cumulative water production. The relationship between permeability and cumulative gas production is represented by a linear curve and that between permeability and surface cumulative liquid production is represented by a cubic polynomial curve. The regression result of the permeability and surface cumulative liquid production agrees with the theoretical mathematical relationship. (paper)

Wood Permeability in Eucalyptus grandis and Eucalyptus dunnii

Directory of Open Access Journals (Sweden)

Raphael Nogueira Rezende

2017-12-01

Full Text Available ABSTRACT The objective of this study was to evaluate the flow of air and water in Eucalyptus grandis and Eucalyptus dunnii wood. Wood was collected from four trees aged 37 years in an experimental plantation of the Federal University of Lavras, Brazil. Planks were cut off the basal logs to produce specimens for air and water permeability testing. Results indicated that the longitudinal permeability to air and water of E. grandis wood were, on average, 5% and 10% higher, respectively, than that of E. dunnii wood. E. grandis and E. dunnii wood showed neither air nor water flow in the test for permeability transversal to the fibers, and longitudinal permeability to air exceeded that to water by approximately 50 fold in both species.

Recent activities on water detritiation technology in JAEA

Energy Technology Data Exchange (ETDEWEB)

Iwai, Yasunori, E-mail: iwai.yasunori@jaea.go.jp [Japan Atomic Energy Agency, Tokai, Naka, Ibaraki 319-1195 (Japan); Kubo, Hitoshi; Ohshima, Yusuke; Noguchi, Hiroshi; Taniuchi, Junichi [Tanaka Kikinzoku Kogyo K.K., Wadai, Tsukuba, Ibaraki 300-4247 (Japan)

2016-11-01

Highlights: • Water detritiation technology has been developed for the Japanese fusion DEMO plant. • Durability of an ion exchange membrane was checked with concentrated tritiated water. • Hydrophobic catalyst of SiO{sub 2} substrate has been developed for water detritiation. - Abstract: Japan Atomic Energy Agency has developed the water detritiation technology for CECE process considering the escalation in quantity and tritium concentration of tritiated water to be processed toward realization of the Japanese fusion DEMO plant. A commercial ion exchange perfluoro-membrane for concentrated tritiated water electrolyzer is durable against irradiation up to 1500 kGy in view of mechanical strength and ion exchange capacity. Concerning hydrophobic catalyst for LPCE column, a new method of manufacturing catalysts involving hydrophobic processing with an inorganic substance base has been developed. The catalyst created with this method has achieved the highest exchange efficiency, equivalent to 1.3 times the previously most powerful efficiency.

Polyurethane Membranes Modified with Isopropyl Myristate as a Potential Candidate for Encapsulating Electronic Implants: A Study of Biocompatibility and Water Permeability

Directory of Open Access Journals (Sweden)

Deepen Paul

2010-07-01

Full Text Available Medical polyurethanes have shown good bio-stability and mechanical properties and have been used as coating for implantable medical devices. However, despite their excellent properties, they are relatively permeable to liquid water and water vapour which is a drawback for electronic implant encapsulation. In this study polyether polyurethanes with different soft segment molecular weights were modified by incorporating isopropyl myristate (IPM, as a hydrophobic modifying agent, and the effect of IPM on water resistant and biocompatibility of membranes were investigated. IPM changed the surface properties of the polyurethane film and reduced its surface energy. Polyurethane films were found to be stable with IPM concentrations of 1–5 wt% based upon their chemistry; however it leached out in BSA at higher concentrations. Though, low concentrations of IPM reduced both liquid water and water vapour permeability; at higher IPM content liquid permeability did not improved significantly. In general, the polyurethane materials showed much lower water permeability compared with currently used silicone packaging material for electronic implants. In addition, cytotoxicity assessment of IPM containing polyurethanes showed no evidence of cytotoxcity up to 5 wt% IPM.

Radiation genetic injury and metabolic difference of tritiated thymidine in testis of young and adult mice

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Lun; Shoupeng, Zhu

1990-04-01

The radiogenetoxicological effects on the adult testis and the metabolic difference of tritiated thymidine between the testis of young and adult BALB/C mice were studied. When 0.037 MBq/g.b.w. of tritiated thymidine was given i.v. to mice, the initial burden of tritium in the adult was larger than that of tritium in the young. But the retention of tritium in testis of the young gradually become larger than that of tritium in the adult with the passing time. Tritiated thymidine which was incorporated into DNA of the male germ cell nuclei damaged the genetic materials and caused the rising of the rates of the dominant lethal and the dominant mutation which produced skeletal abnomalities in the offspring. The relationship between the dominant lethal mutation index (Y) and the injected activity of tritiated thymidine (I, MBq/g.b.w.) is described by Y = 74.13 + 80.20 I (r = 0.95). The relationship between the incidence of the dominant skeletal mutation in the offspring (B) and the injected activity is B = 0.16 + 0.079 I ( r = 0.85).

Radiation genetic injury and metabolic difference of tritiated thymidine in testis of young and adult mice

International Nuclear Information System (INIS)

Lun Mingyue; Zhu Shoupeng.

1990-01-01

The radiogenetoxicological effects on the adult testis and the metabolic difference of tritiated thymidine between the testis of young and adult BALB/C mice were studied. When 0.037 MBq/g.b.w. of tritiated thymidine was given i.v. to mice, the initial burden of tritium in the adult was larger than that of tritium in the young. But the retention of tritium in testis of the young gradually become larger than that of tritium in the adult with the passing time. Tritiated thymidine which was incorporated into DNA of the male germ cell nuclei damaged the genetic materials and caused the rising of the rates of the dominant lethal and the dominant mutation which produced skeletal abnomalities in the offspring. The relationship between the dominant lethal mutation index (Y) and the injected activity of tritiated thymidine (I, MBq/g.b.w.) is described by Y = 74.13 + 80.20 I (r = 0.95). The relationship between the incidence of the dominant skeletal mutation in the offspring (B) and the injected activity is B = 0.16 + 0.079 I ( r = 0.85)

Trees as indicators of subterranean water flow from a retired radioactive waste disposal site

International Nuclear Information System (INIS)

Rickard, W.H.; Kirby, L.J.

1987-01-01

Tree sampling helped locate a subterranean flow of tritiated water from a low-level radioactive waste disposal site that had not been detected by well water monitoring alone. Deciduous trees growing in a natural forest on the hillsides downslope from the site were sampled for the presence of tritiated water in sap of maple trees and in leaf water extracted from oak and hickory trees. Elevated concentrations of 3 H were detected in the leaf water extracted from several trees located 50 m downslope from the western boundary of the fenced exclusion zone. A 3-m-deep well drilled near these trees indicated that the source of tritiated water was a narrow zone of subterranean flow

Electron-microscopic autoradiography of tritiated testosterone in rat testis

International Nuclear Information System (INIS)

Frederik, P.M.; Molen, H.J. van der; Galjaard, H.; Klepper, D.

1977-01-01

The feasibility of a technique for autoradiography of diffusible substances has been further tested by analysing the localization of steroids in rats testes with the light- and electron-microscope. Testes of rats were perfused with tritiated testosterone (3 min) followed by 15-min perfusion with buffer containing a 100-fold excess of unlabelled testosterone. Tissue samples were frozen, freeze dried, fixed in osmium vapour and embedded in Epon. To exclude extraction of steroids, contact with water and other solvents was prevented during cutting of thin sections on an ultracryotome and further treatment for autoradiography. Light- and electron-microscopic observations indicated that the highest concentration of labelled testosterone was present within the basal parts of the Sertoli cell cytoplasm and in lipid inclusions of Sertoli cells within the seminiferous tubules. This is the first account of autoradiography of steroids at the electron-microscope level. (author)

Storage of solid tritiated waste for which there is no management solution; L'entreposage des dechets solides trities sans filiere

Energy Technology Data Exchange (ETDEWEB)

Fromonot, C.; Rancher, J. [CEA Bruyeres-le-Chatel, Dir. des applications militaires, 91 (France); Douche, Ch.; Guetat, Ph. [CEA Valduc, Dir. des applications militaires, 21 - Is-sur-Tille (France)

2011-02-15

In France, radioactive waste that contains tritium, the radioactive isotope of hydrogen, is produced by the CEA as part of its research and development activities, especially for military applications. There is currently no definitive disposal solution for this waste, so it is processed and packaged and then kept in interim storage at Valduc and Marcoule. Furthermore, industrial companies and medical and pharmaceutical research laboratories use tritium - or have done so in the past - for a number of applications which have led to the production of tritiated waste, a small amount of which is still awaiting a disposal solution. Lastly, beginning in the 2020 years, the ITER power plant will also generate tritiated waste and become the largest source of its production. 6 categories of tritiated waste have been defined. Only the very lowest concentrations of tritiated waste can be dealt with by the processing and disposal solutions currently available. This means CENTRACO, where very low-level tritiated waste can be incinerated or melted, and ANDRA repositories, where the acceptance criteria are very strict, making it very uncommon for them to be used for tritiated waste. This situation is a result of the characteristics of tritium and the history of the Aube repository. The proposed solution is based on a temporary storage (50 years) of tritiated waste near the production zone that will allow a natural diminution of the radioactivity and then the packages will be moved to future storing centers of ANDRA that will be built to receive tritiated wastes

Evaluation of permeable and non-permeable tritium in normal condition in a fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Marta, V; Manuel, P J [Instituto de Fusion Nuclear (DENIM)/ETSII, Universidad Politecnica Madrid (UPM) (Spain); Sedano Luis, A [Ministerio de Educacion y Ciencia, Ciemat (Spain)], E-mail: marta@denim.upm.es

2008-05-15

The tritium cycle, technologies of process and control of the tritium in the plant will constitute a fraction of the environmental impact of the first generation of DT fusion reactors. The efforts of conceptual development of the tritium cycle are centered in the Internal Regenerator Cycle. The tritium could be recovered from a flow of He gas, or directly from solid breeder. The limits of transfers to the atmosphere are assumed {approx} 1 gr-T/a ({approx}20 Ci/a) (without species distinction). In the case of ITER, for example, we have global demands of control of 5 orders of magnitude have been demonstrated at experimental level. The transfer limits determine the key parameters in tritium Cycle (HT, HTO, as dominant, and T2, T2O as marginal). Presently, the transfer from the cycle to the environment is assumed through the exchange system of the power plant (primary to secondary). That transport is due to the permeation through HT, T2, or leakage to the coolant in the primary system. It is key the chemical optimization in the primary system, that needs to be reanalyzed in terms of radiological impact both for permeable, HT, T2, and non-permeable HTO, T2O. It is necessary considered the pathway of tritium from the reactor to the atmosphere, these processes are modelled adequately. Results of the assessments were early and chronic doses which have been evaluated for the Most Exposed Individual at particular distance bands from the release point. The impact evaluations will be performed with the computational tools (NORMTRI), besides national regulatory models, internationally accepted computer these code for dosimetric evaluations of tritiated effluents in operational conditions.

Relative biological effectiveness of tritiated water on human chromosomes of lymphocytes and bone marrow cells

International Nuclear Information System (INIS)

Tanaka, Kimio; Sawada, Shozo; Kamada, Nanao

1992-01-01

One of the major toxic effluent from nuclear power industries is tritiated water (HTO), which is released into the environment in large quantities. Low dose radiation effects and dose rate effects of HTO on human lymphocytes and bone marrow cells are not well studied. The present study was performed to investigate dose-response relationship for chromosome aberration frequencies in the human lymphocytes and bone marrow cells, by HTO in-vitro exposure at low dose ranges of 0.1 to 1 Gy. Go lymphocytes and bone marrow cells were incubated for 10 - 150 minutes with HTO at 2 cGy/min. Also 60 Co γ and 137 Cs γ rays were used as controls. Dicentric chromosomes were scored in 1,000 to 2,000 cells of each experimental series. The RBE values of HTO at low dose range for the induction of dicentric chromosomes and chromatid type aberrations were 2.7 in lymphocytes and approximately 3.8 in bone marrow cells with respect to 60 Co γ ray, respectively. Also lymphocytes were chronically exposed to HTO for 24 to 72 hrs at lower dose rates (0.2 and 0.05 cGy/min). The yields of dicentrics and rings decreased with the reduction in the dose rate of HTO, presenting a clear dose rate effects of HTO. These results provide an useful information for the assessment for health risk in humans exposed to low concentration level to HTO. (author)

Carbon-based building blocks for alcohol dehydration membranes with disorder-enhanced water permeability

DEFF Research Database (Denmark)

Boffa, Vittorio; Etmimi, H.; Mallon, P.E.

2017-01-01

Graphene oxide (GO) thin films have demonstrated outstanding water permeability and excellent selectivity towards organic molecules and inorganic salts, unlocking a new exciting direction in the development of nanofiltration, desalination and pervaporation membranes. However, there are still high......-HAL membranes promising devices for alcohol dehydration technologies....

Microorganism Removal in Permeable Pavement Parking Lots ...

Science.gov (United States)

Three types of permeable pavements (pervious concrete, permeable interlocking concrete pavers, and porous asphalt) were monitored at the Edison Environmental Center in Edison, New Jersey for indicator organisms such as fecal coliform, enterococci, and E. coli. Results showed that porous asphalt had much lower concentration in monitored infiltrate compared to pervious concrete and permeable interlocking concrete pavers. Concentrations of monitored organisms in infiltrate from porous asphalt were consistently below the bathing water quality standard. Fecal coliform and enterococci exceeded bathing water quality standards more than 72% and 34% of the time for permeable interlocking concrete pavers and pervious concrete, respectively. Purpose is to evaluate the performance of permeable pavement in removing indicator organisms from infiltrating stormwater runoff.

Dry decontamination for tritiated wastes

International Nuclear Information System (INIS)

Shi Zhengkun; Wu Tao; Dan Guiping; Xie Yun

2009-01-01

To aim at decontamination of tritiated wastes, we have developed and fabricated a dry tritium decontamination system, which is designed to reduce tritium surface contamination of various alloy by UV, ozone and heating. The result indicates that the elevation of temperature can obviously improve decontamination effect. With 3 h irradiation by 365 nm UV at 220 degree C, it has a decontamination rate of 99% to stainless steel surface. Ozone can more obviously improve decontamination effect when metal was heated. Ozone has a decontamination effect beyond 95% to stainless steel, aluminum and brass at 220 degree C. Tritium surface concentration of metal has a little increase after decontamination. (authors)

Update to Permeable Pavement Research at the Edison ...

Science.gov (United States)

The EPA’s Urban Watershed Management Branch (UWMB) has been monitoring the permeable pavement demonstration site at the Edison Environmental Center, NJ since 2010. This site has three different types of permeable pavements including interlocking concrete permeable pavers, pervious concrete, and porous asphalt. The permeable pavements are limited to parking spaces while adjacent driving lanes are impermeable and drain to the permeable surfaces. The parking lot is instrumented for continuous monitoring with thermistors and water content reflectometers that measure moisture as infiltrate passes through the storage gallery beneath the permeable pavements into the underlying native soil. Each permeable surface of the parking lot has four lined sections that capture infiltrate in tanks for water quality analyses; these tanks are capable of holding volumes up to 4.1 m3, which represents up to 38 mm (1.5 in.) for direct rainfall on the porous pavement and runoff from adjacent driving lanes that drain into the permeable surface.Previous technical releases concerning the demonstration site focused on monitoring techniques, observed chloride and nutrient concentrations, surface hydrology, and infiltration and evaporation rates. This presentation summarizes these past findings and addresses current water quality efforts including pH, solids analysis, total organic carbon, and chemical oxygen demand. Stormwater runoff continues to be a major cause of water pollution in

Radiation doses to the tissues of rat from tritiated thymidine administered by three different routes

International Nuclear Information System (INIS)

Takeda, Hiroshi; Iwakura, Tetsuo; Mabuchi, Yasuo.

1984-01-01

Biological behaviour of tritiated thymidine were investigated in rat over 120 days after oral, intraperitoneal or intravenous administration and the absorbed doses to different tissues were estimated. The result of present study revealed that the absorbed dose from tritiated thymidine varied with the route of administration. Among the three routes of administration, intraperitoneal injection gave the highest dose to all of the tissues examined. A significant difference due to the route of administration was found in spleen and small intestine, where the doses were, respectively, 3.3 and 4.5 times higher after intraperitoneal injection than after oral ingestion. The difference was substantially dependent on the dose value from non-volatile tritium which would be incorporated into DNA. Present observation suggests that the radiation hazards of tritiated thymidine differ depending on the route of entry into the body. (author)

Genetic and haematopoietic effects of long-term tritiated water ingestion in mice

International Nuclear Information System (INIS)

Carsten, A.L.; Cronkite, E.P.

1976-01-01

The effect of large amounts of tritiated water (HTO) from reactors on the environment is evaluated. Randomly bred mice of the Hale-Stoner-Brookhaven strain have been maintained on HTO (3 μCi/mlitre) for extended periods. First-generation animals on HTO from four weeks of age have been evaluated for changes in growth pattern, and second-generation animals (also on HTO) for breeding efficiency, dominant lethal mutation rate and bone-marrow integrity. A total of 18831 embryos were examined. Statistical analysis of these results using either Student's ''t'' test or Kruskal and Wallis rank test indicates that there was a significant (p<0.01) reduction in viable embryos and an increase in early deaths in matings involving animals drinking HTO. Beginning at eight weeks of age and monthly thereafter, the haematopoietic stem cell content of the bone marrow was determined using the exogenous spleen colony technique. Although the total cellularity of the bone marrow remains comparable in the control and treated groups, the total number of stem cells (CFU) was reduced beginning after approximately 12-20 weeks on the tritium regime. These findings indicate a reduction in the total number of pluripotent stem cells in the marrow together with the ability of this reduced number of cells to maintain normal levels of total cellularity in the bone marrow. Thus, continuous ingestion of HTO at a concentration of 3 μCi/mlitre by mice results in: (1) Reduction in number of viable embryos present in the female at late pregnancy from matings when either the female or both parents have been on HTO; (2) Increase in number of early post-implantation deaths when both parents are on HTO; (3) Reduction in bone-marrow stem cell content after 12 weeks or longer on HTO; (4) No apparent effect on breeding efficiency (percentage of females pregnant) or body weight. These results are discussed in relation to the accumulated radiation dose

Deposition of LDH on plasma treated polylactic acid to reduce water permeability

KAUST Repository

Bugatti, Valeria

2013-04-01

A simple and scalable deposition process was developed to prepare polylactic acid (PLA) coatings with enhanced water barrier properties for food packaging applications. This method based on electrostatic interactions between the positively charged layers of layered double hydroxides (LDHs) modified with ionic liquids (ILs) and the negatively charged plasma treated polylactic acid leads to homogeneous, stable, and highly durable coatings. Deposition of the LDH coatings increases the surface hydrophobicity of the neat PLA, which results to a decrease in water permeability by about 35%. © 2013 Elsevier Inc.

Mutagenic effect of tritated water on spores of Bacillus subtilis

International Nuclear Information System (INIS)

Tanooka, H.; Munakata, N.

1978-01-01

The mutagenic effect of tritiated water was observed with spores of Bacillus subtilis polA strain suspended in 50 mCi/ml of tritiated water for various intervals. Dose rate given by tritium beta particles to spore core was estimated to be 400 rad/hr from some assumptions and E. coli data computed by Bockrath et al. and Sands et al. The initial mutation rate was 4.2 x 10 -9 mutants/rad, as compared with 2.4 x 10 -9 mutants/rad for 60 Co γ rays and 3.3 x 10 -9 mutants/rad for 30-kVp x rays. The mutagenic effect of tritiated water on spores is most likely due to beta particle ionizing radiation damage

Skin lipid structure controls water permeability in snake molts.

Science.gov (United States)

Torri, Cristian; Mangoni, Alfonso; Teta, Roberta; Fattorusso, Ernesto; Alibardi, Lorenzo; Fermani, Simona; Bonacini, Irene; Gazzano, Massimo; Burghammer, Manfred; Fabbri, Daniele; Falini, Giuseppe

2014-01-01

The role of lipids in controlling water exchange is fundamentally a matter of molecular organization. In the present study we have observed that in snake molt the water permeability drastically varies among species living in different climates and habitats. The analysis of molts from four snake species: tiger snake, Notechis scutatus, gabon viper, Bitis gabonica, rattle snake, Crotalus atrox, and grass snake, Natrix natrix, revealed correlations between the molecular composition and the structural organization of the lipid-rich mesos layer with control in water exchange as a function of temperature. It was discovered, merging data from micro-diffraction and micro-spectroscopy with those from thermal, NMR and chromatographic analyses, that this control is generated from a sophisticated structural organization that changes size and phase distribution of crystalline domains of specific lipid molecules as a function of temperature. Thus, the results of this research on four snake species suggest that in snake skins different structured lipid layers have evolved and adapted to different climates. Moreover, these lipid structures can protect, "safety", the snakes from water lost even at temperatures higher than those of their usual habitat. Copyright © 2013 Elsevier Inc. All rights reserved.

The permeability of concrete for reactor containment vessels

International Nuclear Information System (INIS)

Mills, R.H.

1983-07-01

Review of the literature pertaining to water, water vapour and gas transmission through concrete revealed conflicting views on the mechanisms involved and the influence of mix design parameters such as initial porosities and water/cement ratio. Consideration of the effects of ageing and of construction defects in field concrete were totally neglected in published work. Permeability data from three published papers were compared with permeability calculated according to Powers. The ratio of calculated to observed permeability varied from 40 x 10 -3 to 860 x 10 -3 for one group: from 0.17 x 10 3 to 8.6 x 10 3 in the second; and from 24 x 10 3 to 142 x 10 3 for the third. There were therefore wide discrepancies within each group of data and between groups. A bibliography was prepared and an exploratory experimental programme was mounted to determine the relative importance of key parameters such as cement type, porosity and water/cement ratio. Contrary to frequently cited references it was found that permeability of concrete was not significantly influenced by water/cement ratio when the starting porosity was constant. If water/cement ratio was held constant, however, the permeability was strongly influenced by starting porosity. It was also found that with constant water/cement ratio permeability increased with cement content. The value of fly ash and blast furnace slag in partial substitution for Portland cement is neglected in the literature but it is important since such substitutions alleviate alkali-silicate reactions. Permeability of concrete was significantly decreased by partial substitution of Portland cement with fly ash but there was no benefit in the use of blast furnace slag

The mass transfers of water by diffusion and permeation through a covering of wastes disposal

International Nuclear Information System (INIS)

Beaudoing, G.; Duding, B.; Margrita, R.; Launay, M.

1991-01-01

The purpose of the experiments described in this article is to measure the transfer conditions similarly to the reality 'in situ', for a barrier constituted of sodic bentonite. For that purpose, these experiments were realized with a possibility of distension into the material receiving the membrane. The studied samples are constituted by a film of heavy, strong, durable and supple propylene coated with a bed of particles of sodic mineral bentonite. This clay is covered with a thin film of polyester for the mechanical protection (transport, placing). The characterisation of water transfer was realized with non mineral tritiated water HTO, nH 2 0 with a specific activity of 37 GBq.m -3 (1 Ci.m -3 ) and placed in the upward cavity of the permeameter. Diffusion, permeation and permeability coefficients are determined under pressure of 0.15.10 5 Pa (1.50 meter of water) and 10 5 Pa (10 meters of water)

The Effect Of Anisotropy In Formation Permeability On The Efficiency Of Cyclic Water Flooding

Directory of Open Access Journals (Sweden)

Al-Obaidi SH

2017-11-01

Full Text Available In oil industry one of the most worldwide used methods a among the hydrodynamic enhanced oil recovery methods is the water flooding including the cyclic water flooding. The efficiency of cyclic water flooding is affected by a number of geophysical and field technological factors. In this work and based on three-dimensional hydrodynamic simulation it is shown that anisotropy of formation permeability has significant effect on justification of the half-cycle time and the technological effectiveness of the method.

Influence of Palm Oil Fuel Ash and W/B Ratios on Compressive Strength, Water Permeability, and Chloride Resistance of Concrete

Directory of Open Access Journals (Sweden)

Wachilakorn Sanawung

2017-01-01

Full Text Available This research studies the effects of W/B ratios and palm oil fuel ash (POFA on compressive strength, water permeability, and chloride resistance of concrete. POFA was ground until the particles retained on sieve number 325 were less than 5% by weight. POFA was used to partially replace OPC at rates of 15, 25, and 35% by weight of binder. The water to binder (W/B ratios of concrete were 0.40 and 0.50. The compressive strength, water permeability, and chloride resistance of concrete were investigated up to 90 days. The results showed that POFA concrete with W/B ratio of 0.40 had the compressive strengths ranging from 45.8 to 55.9 MPa or 82–94% of OPC concrete at 90 days, while POFA concrete with W/B ratio of 0.50 had the compressive strengths of 33.9–41.9 MPa or 81–94% of OPC concrete. Furthermore, the compressive strength of concrete incorporation of ground POFA at 15% was the same as OPC concrete. The water permeability coefficient and the chloride ion penetration of POFA concrete were lower than OPC concrete when both types of concrete had the same compressive strengths. The findings also indicated that water permeability and chloride ion penetration of POFA concrete were significantly reduced compared to OPC concrete.

Theoretical prediction of thermodynamic properties of tritiated beryllium molecules and application to ITER source term

Energy Technology Data Exchange (ETDEWEB)

Virot, F., E-mail: francois.virot@irsn.fr; Barrachin, M.; Souvi, S.; Cantrel, L.

2014-10-15

Highlights: • Standard enthalpies of formation of BeH, BeH{sub 2}, BeOH, Be(OH){sub 2} have been calculated. • The impact of hydrogen isotopy on thermodynamic properties has been shown. • Speciation in the vacuum vessel shows that the main tritiated species is tritiated steam. • Beryllium hydroxide and hydride could exist during an accidental event. - Abstract: By quantum chemistry calculations, we have evaluated the standard enthalpies of formation of some gaseous species of the Be-O-H chemical system: BeH, BeH{sub 2}, BeOH, Be(OH){sub 2} for which the values in the referenced thermodynamic databases (NIST-JANAF [1] or COACH [2]) were, due to the lack of experimental data, estimated or reported with a large uncertainty. Comparison between post-HF, DFT approaches and available experimental data allows validation of the ability of an accurate exchange-correlation functional, VSXC, to predict the thermo-chemical properties of the beryllium species of interest. Deviation of enthalpy of formation induced by changes in hydrogen isotopy has been also calculated. From these new theoretically determinated data, we have calculated the chemical speciation in conditions simulating an accident of water ingress in the vacuum vessel of ITER.

A plate reader-based method for cell water permeability measurement

DEFF Research Database (Denmark)

Fenton, Robert A.; Moeller, H B; Nielsen, S

2010-01-01

Cell volume and water permeability measurements in cultured mammalian cells are typically conducted under a light microscope. Many of the employed approaches are time consuming and not applicable to a study of confluent epithelial cell monolayers. We present here an adaptation of a calcein......: AQP2-S256D > AQP2 wild-type > AQP2-S256A. We propose that the method can be applied to study AQP function and more generally to study cell volume changes in adherent cell lines. Furthermore, it should be adaptable for AQP inhibitor screening in chemical compound libraries....

Measurements of gas permeability and non-Darcy flow in gas-water-hydrate systems

Energy Technology Data Exchange (ETDEWEB)

Ersland, G.; Husebo, J.; Graue, A.; Kvamme, B. [Bergen Univ., Bergen (Norway). Dept. of Physics and Technology; Baldwin, B. [Green Country Petrophysics LLC, Dewey, OK (United States); Stevens, J.; Howard, J. [ConocoPhillips, OK (United States)

2008-07-01

Storage of carbon dioxide (CO{sub 2}) in natural gas hydrate reservoirs may offer stable long-term storage of a greenhouse gas while benefiting from methane production, without requiring heat. By exposing hydrate to a thermodynamically preferred hydrate former, CO{sub 2}, the hydrate may be maintained macroscopically in the solid state and retain the stability of the formation. However, there is concern over the flow capacity in such reservoirs. This depends on several factors, notably thermodynamic destabilization of hydrate in small pores due to capillary effects; the presence of liquid channels separating the hydrate from the mineral surfaces; and, the connectivity of gas or liquid filled pores and channels. This paper described a technique for measuring gas permeability in gas-water-hydrate systems. It reported on several experiments that measured gas permeability during stages of hydrate growth in sandstone core plugs. Interactions between minerals and surrounding molecules were also discussed. The formation of methane hydrate in porous media was monitored and quantified with magnetic resonance imaging (MRI). MRI images of hydrate growth within the porous rock were provided along with measurements of gas permeability and non-Darcy flow effects at various hydrate saturations. Gas permeability was measured at steady state flow of methane through the hydrate-bearing core sample. Significant gas permeability was recorded for porous sandstone even when hydrates occupied up to 60 per cent of the pore space. It was concluded that MRI imaging can be used effectively to map and quantify hydrate saturation in sandstone core plugs. 27 refs., 2 tabs., 10 figs.

Effects of prenatal low dose beta radiation from tritiated water on rat hippocampus neurons. Electrophysiological and neuro behavioural changes

International Nuclear Information System (INIS)

Gao Weimin; Zhou Xiangyan

1997-01-01

Pregnent Wistar rats were exposed to tritiated water (HTO) on day 13 of gestation so that for their offsprings, the absorbed doses were estimated to be 0.000, 0.044, 0.088 and 0.264 Gy. The influence of HTO to the morphology and number of hippocampus pyramidal neurons and the maximum electric current of Ca 2+ in neurons was observed for the in-vitro-cultured hippocampus of new-born rats and the learning and memory behaviours were assessed by the electric avoidance reflex test in a Y-maze and the condition reflex test for young rats. The results show that prenatal exposure to HTO in a cumulative dose of 0.088 Gy can cause a reduction in number of neurons in hippocampus cultured in vitro, and that the electric current of Ca 2+ tends to decline with cumulative dose increasing, with the significant decrease in offsprings prenatally exposed to HTO in dose of 0.264 Gy. The results of electric avoidance reflex test in a Y-maze and condition reflex test indicate that for young rats prenatally exposed to HTO, a cumulative dose of 0.088 Gy could induce damage in their learning and memory behaviours

Synthesis of tritiated sex pheromones of the processionary moth Thaumetopoea pityocampa and the Egyptian armyworm Spodoptera littoralis

International Nuclear Information System (INIS)

Guerrero, Angel; Feixas, Joan

1996-01-01

Synthesis of tritiated sex phenomones of the processionary moth Thaumetopoea pityocampa and the Egyptian armyworm Spodoptera littoralis has been accomplished by a simple route involving tritiated sodium borohydride reduction of the corresponding aldehyde followed by acetylation of the resulting radiolabelled alcohol. The process occurs with high chemical and radiochemical yields and the compounds have been used in pheromone catabolism studies. (author)

Synthesis of a tritiated herbicide with high activity: methyl thifensulfuron

International Nuclear Information System (INIS)

Bastide, J.; Ortega, F.

1993-01-01

In order to study the binding on acetolactate synthase, a tritiated herbicide sulfonylurea (thifensulfuron methyl) of high specific activity was synthesized. By use of C 3 H 3 I for esterification of an acid group, a rapid incorporation of tritium into this compound may be achieved. (Author)

Gas and water permeability tests of 25 year old concrete from the NPD Nuclear Generating Station

International Nuclear Information System (INIS)

Mills, R.H.

1990-05-01

Permeability tests on cores recovered from concrete which had been in service for 25 years in the Nuclear Power Demonstration (NPD) reactor showed rates of mass transfer of gas and water which were greater than young fresh concrete of the same proportions and that reported in previous AECB reports. This transparency of the concrete was also 2 orders of magnitude greater than that of comparable concrete which had been stored in the laboratory atmosphere for 19 years. Analysis of the effluent in water permeability tests revealed the presence of unusual amounts of soluble materials, mainly Na and K but little Ca, in the reactor concrete. This suggested service-related deterioration of the concrete rather than the release of soluble Ca by continuing hydration of cement

The evaluation of uptake of tritiated methane to the plants

International Nuclear Information System (INIS)

Kakiuchi, Hideki; Andoh A, Mariko; Amano, Hikaru

2003-01-01

The experiment of the exposure of tritiated methane (CH 3 T) to plants was carried. Plants were put in the airtight container that CH 3 T gas was added. The amount of light that it irradiated plants was changed, and the amounts of photosynthesis as the metabolic change activities of the plants were adjusted, and processes of assimilation to the plant of CH 3 T were evaluated under a constant temperature. The leaves in the container and the inside gas were collected in every interval, and tritium concentrations in the samples were determined. It is observed that CH 3 T concentration in the container decreased under both the light and dark conditions. On changing from dark to light condition, there was no change in the decreasing tendency of the CH 3 T concentration. These show that tritiated methane would be taken in the plants without the photosynthesis process, but through the oxidation by microorganism on plants. (author)

Biological study of a tritiated luminous paint (1962)

International Nuclear Information System (INIS)

Remy, J.; Meunier, J.; Aeberhardt, A.

1962-01-01

A powdered mixture of zinc sulphide and a tritiated polyester has been administered to rats by means of the oesophageal probe. The distribution of tritium in the organ, and its elimination, have been studied. It appears that from 75 to 80 per cent of the polyester has undergone sufficient degradation in the intestinal medium to be absorbed by the digestive mucous membrane and to be subjected to metabolic reactions. (authors) [fr

Measurement of relative permeability of fuel cell diffusion media

KAUST Repository

Hussaini, I.S.

2010-06-01

Gas diffusion layer (GDL) in PEM fuel cells plays a pivotal role in water management. Modeling of liquid water transport through the GDL relies on knowledge of relative permeability functions in the in-plane and through-plane directions. In the present work, air and water relative permeabilities are experimentally determined as functions of saturation for typical GDL materials such as Toray-060, -090, -120 carbon paper and E-Tek carbon cloth materials in their plain, untreated forms. Saturation is measured using an ex situ gravimetric method. Absolute and relative permeability functions in the two directions of interest are presented and new correlations for in-plane relative permeability of water and air are established. © 2010 Elsevier B.V. All rights reserved.

Simulation for Synthesis of Tritiated Styrene by Catalyzed Addition of Deuterium

Directory of Open Access Journals (Sweden)

CUI Xiao-jing;KANG Yi;HU Shi-lin

2016-08-01

Full Text Available Tritiated styrene plays an important role in the organic tritium lights, which could be made by selective hydrogenation of phenylacetylene. A simulated reaction of the preparation of tritiated styrene was studied by using deuterium instead of tritium and using the Lindlar catalyst instead of Pd/C catalyst to improve the conversion and selectivity of the reaction. Experiment results showed that stirring speed, temperature and the amount of deuterium were the most important factors to effect the conversion and selectivity of the reaction. The relative stronger stirring speed and higher temperature could improve the conversion rate of the reaction, but could not change the selectivity. When the excessive or less deuterium was added in the reaction, the selectivity was decreased significantly, since the over deuterium promoted the reaction toward ethylbenzene. Lindlar catalyst exhibited higher selectivity toward styrene than Pd/C.

A light-water detritiation project at Chalk River Laboratories

International Nuclear Information System (INIS)

Boniface, H.A.; Castillo, I.; Everatt, A.E.; Ryland, D.K.

2010-01-01

The NRU reactor rod bays is a large, open pool of water that receives hundreds of fuel rods annually, each carrying a small amount of residual tritiated heavy water. The tritium concentration of the rod bays water has risen over the years, to a level that is of concern to the operations staff and to the environment. The proposed long-term solution is to reduce the rod bays tritium concentration by direct detritiation of the water. The Combined Electrolytic-Catalytic Exchange (CECE) process is well suited to the light-water detritiation problem. With a tritium-protium separation factor greater than five, a CECE detritiation process can easily achieve the eight orders of magnitude separation required to split a tritiated light-water feed into an essentially tritium-free effluent stream and a tritiated heavy water product suitable for recycling through a heavy water upgrader. This paper describes a CECE light-water detritiation process specifically designed to reduce the tritium concentration in the NRU rod bays to an acceptable level. The conceptual design of a 600 Mg/a detritiation process has been developed and is now at the stage of project review and the beginning of detailed design. (author)

Defining clogging potential for permeable concrete.

Science.gov (United States)

Kia, Alalea; Wong, Hong S; Cheeseman, Christopher R

2018-08-15

Permeable concrete is used to reduce urban flooding as it allows water to flow through normally impermeable infrastructure. It is prone to clogging by particulate matter and predicting the long-term performance of permeable concrete is challenging as there is currently no reliable means of characterising clogging potential. This paper reports on the performance of a range of laboratory-prepared and commercial permeable concretes, close packed glass spheres and aggregate particles of varying size, exposed to different clogging methods to understand this phenomena. New methods were developed to study clogging and define clogging potential. The tests involved applying flowing water containing sand and/or clay in cycles, and measuring the change in permeability. Substantial permeability reductions were observed in all samples, particularly when exposed to sand and clay simultaneously. Three methods were used to define clogging potential based on measuring the initial permeability decay, half-life cycle and number of cycles to full clogging. We show for the first time strong linear correlations between these parameters for a wide range of samples, indicating their use for service-life prediction. Copyright © 2018 Elsevier Ltd. All rights reserved.

Serpentinization: Getting water into a low permeability peridotite

Science.gov (United States)

Ulven, Ole Ivar

2017-04-01

Fluid consuming rock transformation processes occur in a variety of settings in the Earth's crust. One such process is serpentinization, which involves hydration of ultramafic rock to form serpentine. With peridotite being one of the dominating rocks in the oceanic crust, this process changes physical and chemical properties of the crust at a large scale, increases the amount of water that enters subduction zones, and might even affect plate tectonics te{jamtveit}. A significant number of papers have studied serpentinization in different settings, from reaction fronts progressing over hundreds of meters te{rudge} to the interface scale fracture initiation te{pluemper}. However, the process represents a complicated multi-physics problem which couples external stress, mechanical deformation, volume change, fracture formation, fluid transport, the chemical reaction, heat production and heat flow. Even though it has been argued that fracture formation caused by the volume expansion allows fluid infiltration into the peridotite te{rudge}, it remains unclear how sufficient water can enter the initially low permeability peridotite to pervasively serpentinize the rock at kilometre scale. In this work, we study serpentinization numerically utilizing a thermo-hydro-mechanical model extended with a fluid consuming chemical reaction that increases the rock volume, reduces its density and strength, changes the permeability of the rock, and potentially induces fracture formation. The two-way coupled hydromechanical model is based on a discrete element model (DEM) previously used to study a volume expanding process te{ulven_1,ulven_2} combined with a fluid transport model based on poroelasticity te{ulven_sun}, which is here extended to include fluid unsaturated conditions. Finally, a new model for reactive heat production and heat flow is introduced, to make this probably the first ever fully coupled chemo-thermo-hydromechanical model describing serpentinization. With this model

Water-pipe smoking effects on pulmonary permeability using technetium-99m DTPA inhalation scintigraphy

International Nuclear Information System (INIS)

Aydin, A.; Durak, H.; Ucan, E.S.; Kaya, G.C.; Ceylan, E.; Kiter, G.

2004-01-01

Although extensive work has been done on cigarette smoking and its effects on pulmonary function, there are limited number of studies on water-pipe smoking. The effects of water-pipe smoking on health are not widely investigated. The aim of this study was to determine the effects of water-pipe smoking on pulmonary permeability. Technetium-99m DTPA inhalation scintigraphy was performed on 14 water-pipe smoker volunteers (all men, mean age 53.7±9.8) and 11 passive smoker volunteers (1 woman, 10 men, mean age 43.8±12). Clearance half-time (T 1/2) was calculated by placing a monoexponential fit on the time activity curves. Penetration index (PI) of the radioaerosol was also calculated. PI was 0.58±0.14 and 0.50±0.12 for water-pipe smokers (WPS) and passive smokers (PS) respectively. T 1/2 of peripheral lung was 57.3±12.7 and 64.6±13.2 min, central airways was 55.8±23.5 and 80.1±35.2 min for WPS and PS, respectively (p≤0.05). Forced expiratory volume in one second/forced vital capacity (FEV 1 /FVC)% was 82.1±8.5 (%) and 87.7±6.5 (%) for WPS and PS, respectively (0.025< p≤0.05). We suggest that water-pipe smoking effects pulmonary epithelial permeability more than passive smoking. Increased central mucociliary clearance in water-pipe smoking may be due to preserved humidity of the airway tracts. (author)

The electrochemical corrosion behavior of austenitic alloys, cobalt or nickel based super alloys, structurally hardened martensitic, Inconel, zircaloy, super austenitic, duplex and of Ni-Cr or NTi deposits in tritiated water. 3 volumes

International Nuclear Information System (INIS)

Bellanger, G.

1994-01-01

The redox potential of 3 H 2 O, as well as the corrosion potentials in this medium are found, abnormally, in the trans-passive region. This is completely different from the behavior in the chemical industry or in the water in nuclear powers. With such behavior, there will be breakdowns of the protective oxide layers, and in the presence of chloride there will be immediate pitting. The steels that are most resistant to this behavior are the super austenitic and super Duplex. To avoid corrosion, another solution is to decompose the radiolytic products by imposing a slight reducing potential. Corrosion inhibitors, which are stable in tritiated water, can be used. (author). 69 refs., 421 figs., tabs

Hydro-mechanical coupling and permeability of an unsaturated swelling clay under hydrous and thermal stress: sorption curve and water permeability

International Nuclear Information System (INIS)

Olchitzky, E.

2002-02-01

The use of swelling clay for engineered safety barriers of radioactive waste disposal require the understanding of its thermal-hydro-mechanical behaviour. This work concerns particularly the characterization and the modelling of the behaviour of one of these clays: the FoCa7 clay. The characteristics of the studied material are: the sorption (desorption) curve and the water permeability. For each of them, new experiments have allowed to acquire data in fields still few explored: in temperature (between 20 and 80 C) for the sorption curve and in the unsaturated field for the water permeability. The analysis of these results and of bibliographic data has allowed in one hand to estimate the importance of the hysteresis phenomenon and the temperature influence on the sorption curve and in another hand, to establish the requirement to introduce in the modelling of the sorption curve, a plastic parameter due to the irreversible deformations occurring during the compaction. Moreover, the tests carried out for data acquirement have been used too to give validation elements to the non linear behaviour laws proposed by O. Coussy and P. Dangla for the non saturated porous media. The particularity of these laws is to suppose the existence of an effective constraint in the non saturated field, this shows the importance of the validation elements presented here. (O.M.)

Membrane permeability of the human granulocyte to water, dimethyl sulfoxide, glycerol, propylene glycol and ethylene glycol.

Science.gov (United States)

Vian, Alex M; Higgins, Adam Z

2014-02-01

Granulocytes are currently transfused as soon as possible after collection because they rapidly deteriorate after being removed from the body. This short shelf life complicates the logistics of granulocyte collection, banking, and safety testing. Cryopreservation has the potential to significantly increase shelf life; however, cryopreservation of granulocytes has proven to be difficult. In this study, we investigate the membrane permeability properties of human granulocytes, with the ultimate goal of using membrane transport modeling to facilitate development of improved cryopreservation methods. We first measured the equilibrium volume of human granulocytes in a range of hypo- and hypertonic solutions and fit the resulting data using a Boyle-van't Hoff model. This yielded an isotonic cell volume of 378 μm(3) and an osmotically inactive volume of 165 μm(3). To determine the permeability of the granulocyte membrane to water and cryoprotectant (CPA), cells were injected into well-mixed CPA solution while collecting volume measurements using a Coulter Counter. These experiments were performed at temperatures ranging from 4 to 37°C for exposure to dimethyl sulfoxide, glycerol, ethylene glycol, and propylene glycol. The best-fit water permeability was similar in the presence of all of the CPAs, with an average value at 21°C of 0.18 μmatm(-1)min(-1). The activation energy for water transport ranged from 41 to 61 kJ/mol. The CPA permeability at 21°C was 6.4, 1.0, 8.4, and 4.0 μm/min for dimethyl sulfoxide, glycerol, ethylene glycol, and propylene glycol, respectively, and the activation energy for CPA transport ranged between 59 and 68 kJ/mol. Copyright © 2013 Elsevier Inc. All rights reserved.

Hydrogeology of rocks of low permeability: region studies

International Nuclear Information System (INIS)

Llamas, M.R.

1985-01-01

Hydrogeological regional studies on low permeability rocks are rather scarce in comparison to similar studies on normal permeability rocks. Economic and technological difficulties to develop ground water from these terrains may be the main cause of this scarcity. Several facts may indicate that these studies will increase in the near future. First, the need to supply water to the people living in underdeveloped arid zones over extensive areas of low permeability rocks. Second, the relevant role that some low permeability large groundwater basins may play in conjunctive ground and surface-water use. And last but not least the feasibility of some low permeability rock areas as sites for nuclear waste repositories. Some specific difficulties in these regional studies may be: a) intrinsic difficulties in obtaining representative water samples and measuring hydraulic heads; b) scarcity of observation and/or pumping wells; c) important hydraulic head and chemical properties variations in a vertical direction; d) old groundwater ages; this may require paleohydrological considerations to understand certain apparent anomalies. In most of these regional studies hydrogeochemical methods and modelling (flow and mass transport) may be very valuable tools. 77 references, 7 figures

Capture and retention of tritiated serotonin by the chick notochord

International Nuclear Information System (INIS)

Gerard, Anne; Gerard, Hubert; Dollander, Alexis

1978-01-01

The 3 day old chick notochord capacity to fix tritiated serotonin is maximal in its axis and in cephalic region. Observations permitting to find, the intracellular serotonin binding sites, contribute to an explanation of the capture mechanism and suggest a special direct role of the notochord on the monoaminergic neuron cytodifferentiation [fr

Extravascular lung water and the pulmonary vascular permeability index may improve the definition of ARDS

OpenAIRE

Perel, Azriel

2013-01-01

The recent Berlin definition has made some improvements in the older definition of acute respiratory distress syndrome (ARDS), although the concepts and components of the definition remained largely unchanged. In an effort to improve both predictive and face validity, the Berlin panel has examined a number of additional measures that may reflect increased pulmonary vascular permeability, including extravascular lung water. The panel concluded that although extravascular lung water has improve...

Permeability of crust is key to crispness retention

NARCIS (Netherlands)

Hirte, A.; Hamer, R.J.; Meinders, M.B.J.; Primo-Martin, C.

2010-01-01

Bread loses crispness rapidly after baking because water originating from the wet crumb accumulates in the dry crust. This water accumulation might be increased by the dense and low permeable character of the bread crust. Our objective was to investigate the influence of permeability of the crust on

Urban permeable pavement system design based on “sponge city” concept

Science.gov (United States)

Yu, M. M.; Zhu, J. W.; Gao, W. F.; Xu, D. P.; Zhao, M.

2017-08-01

Based on the “sponge city” concept, to implement the goal of building a city within the city to solve the sponge waterlogging, rational utilization of water resources, reduce water pollution this paper, combined with the city planning level in China, establishes the design system of city road flooding from the macro, medium and micro level, explore the design method of city water permeable pavement system, and has a practical significance the lower flood risk water ecological problems. On the macro level, we established an urban pavement sponge system under the regional ecological pattern by “spot permeable open space - low impact developing rain water road system - catchment area and catchment wetland”. On a medium level, this paper proposed the permeable suitability of pavement and the planning control indicators when combined with urban functional districts to conduct permeable pavement roads plans and controls. On micro level, the paper studied sponge technology design of permeable pavement from road structure, surface material, and other aspects aimed at the pavement permeability requirements.

Influence of transport infrastructure on water permeability of soils of Western Siberia

Science.gov (United States)

Eremin, Dmitry; Eremina, Diana

2017-10-01

Correctly designed transport infrastructure should support the current economic relations. It should provide a reserve for development of economy of the region in the future. In Western Siberia, new highways are actively being built and major repairs of the operating roads are being conducted. Local materials are often used in the roadbed construction. In the Tyumen region, it is usually sandy silt and clayey sand. The soil has unfavourable physico-mechanical properties. The soil is prone to water and wind erosion. This type of ground gets on the adjacent to the road territory. Studies on the influence of highways on soil permeability were carried out on the basis of the federal highway Tyumen-Omsk. Three types of soils, which are actively used in the agricultural sector, were considered. It is found that the content of particles with the size less than 0.01 mm reaches 32% in the soil used in road construction. It is noted that a part of these particles accumulates on the adjacent to the road territory since it is being washed out from roadbed. The content of physical clay (initial values. The width of active accumulation of silt particles reaches 15-20 m along the roads. The soils at the distance up to 10 m from the highway are almost impermeable to water. Absence of a natural hydrological drain, results in the territory bogging. An inverse close correlation was established between the content of physical clay (<0.01 mm) and water permeability (r = 0.90).

Ground-water flow in low permeability environments

Science.gov (United States)

Neuzil, Christopher E.

1986-01-01

Certain geologic media are known to have small permeability; subsurface environments composed of these media and lacking well developed secondary permeability have groundwater flow sytems with many distinctive characteristics. Moreover, groundwater flow in these environments appears to influence the evolution of certain hydrologic, geologic, and geochemical systems, may affect the accumulation of pertroleum and ores, and probably has a role in the structural evolution of parts of the crust. Such environments are also important in the context of waste disposal. This review attempts to synthesize the diverse contributions of various disciplines to the problem of flow in low-permeability environments. Problems hindering analysis are enumerated together with suggested approaches to overcoming them. A common thread running through the discussion is the significance of size- and time-scale limitations of the ability to directly observe flow behavior and make measurements of parameters. These limitations have resulted in rather distinct small- and large-scale approaches to the problem. The first part of the review considers experimental investigations of low-permeability flow, including in situ testing; these are generally conducted on temporal and spatial scales which are relatively small compared with those of interest. Results from this work have provided increasingly detailed information about many aspects of the flow but leave certain questions unanswered. Recent advances in laboratory and in situ testing techniques have permitted measurements of permeability and storage properties in progressively “tighter” media and investigation of transient flow under these conditions. However, very large hydraulic gradients are still required for the tests; an observational gap exists for typical in situ gradients. The applicability of Darcy's law in this range is therefore untested, although claims of observed non-Darcian behavior appear flawed. Two important nonhydraulic

Use of geophysical logs to estimate the quality of ground water and the permeability of aquifers

Science.gov (United States)

Hudson, J.D.

1996-01-01

The relation of formation factor to resistivity of formation water and intergranular permeability has often been investigated, and the general consensus is that this relation is closest when established in a clean-sand aquifer in which water quality does not vary substantially. When these restrictions are applied, the following standard equation is a useful tool in estimating the resistance of the formation water: F = Ro/Rw, where F is the formation factor, which is a function of the effective porosity; Ro is the resistivity of a formation that is 100 percent saturated with interstitial water; and Rw is the resistivity of the water in the saturated zone. However, arenaceous aquifers can have electrical resistivities that are not directly related to resistivity of water or porosity. Surface conductivity and ion exchange are significant factors when the sediments are clay bearing. The solid constituents are a major component of the parameters needed to solve the equation for formation-water resistivity and estimates of aquifer permeability. A correction process needs to be applied to adjust the variables, Ro and F, to the equivalent of clean sand. This report presents an empirical method of using the neutron log and the electrical-resistivity values from long- and short-normal resistivity logs to correct for fine-grained material and the subsequent effects of low impedance to electrical flow that are not related to the resistance of formation water.

Micelle-template synthesis of hollow silica spheres for improving water vapor permeability of waterborne polyurethane membrane

Science.gov (United States)

Bao, Yan; Wang, Tong; Kang, Qiaoling; Shi, Chunhua; Ma, Jianzhong

2017-04-01

Hollow silica spheres (HSS) with special interior spaces, high specific surface area and excellent adsorption and permeability performance were synthesized via micelle-template method using cetyl trimethyl ammonium bromide (CTAB) micelles as soft template and tetraethoxysilane (TEOS) as silica precursor. SEM, TEM, FT-IR, XRD, DLS and BET-BJH were carried out to characterize the morphology and structure of as-obtained samples. The results demonstrated that the samples were amorphous with a hollow structure and huge specific surface area. The growth of HSS was an inward-growth mechanism along template. Notably, we have provided a new and interesting fundamental principle for HSS materials by precisely controlling the ethanol-to-water volume ratio. In addition, the as-obtained HSS were mixed with waterborne polyurethane (WPU) to prepare WPU/HSS composite membrane. Various characterizations (SEM, TEM, FT-IR and TGA) revealed the morphology, polydispersity and adherence between HSS and WPU. Performance tests showed that the introduction of HSS can improve the water vapor permeability of composite membrane, promoting its water resistance and mechanical performance at the same time.

Hydraulic, water-quality, and temperature performance of three types of permeable pavement under high sediment loading conditions

Science.gov (United States)

Selbig, William R.; Buer, Nicolas

2018-05-11

Three permeable pavement surfaces - asphalt (PA), concrete (PC), and interlocking pavers (PIP) - were evaluated side-by-side to measure changes to the infiltrative capacity and water quality of stormwater runoff originating from a conventional asphalt parking lot in Madison, Wisconsin. During the 24-month monitoring period (2014-16), all three permeable pavements resulted in statistically significant reductions in the cumulative load of solids (total suspended solids and suspended sediment), total phosphorus, Escherichia coli (E. coli), and Enterococci. Most of the removal occurred through capture and retention in the void spaces of each permeable surface and aggregate base. The largest reduction in total suspended solids was for PC at 80 percent, followed by PIP and PA at 69 and 65 percent, respectively. Reductions (generally less than 50 percent) in total phosphorus also were observed, which might have been tempered by increases in the dissolved fraction observed in PIP and PA. Conversely, PC results indicated a slight reduction in dissolved phosphorus but failed to meet statistical significance. E. coli and Enterococci were reduced by about 80 percent for PC, almost twice the amount observed for PIP and PA.Results for the PIP and PC surfaces initially indicated higher pollutant load reduction than results for the PA surface. The efficiency of PIP and PC surfaces capturing sediment, however, led to a decline in infiltration rates that resulted in more runoff flowing over, not through, the permeable surface. This result led to a decline in treatment until the permeable surface was partially restored through maintenance practices, to which PIP responded more dramatically than PC or PA. Conversely, the PA surface was capable of infiltrating most of the influent runoff volume during the monitoring period and, thus, continued to provide some level of treatment. The combined effect of underdrain and overflow drainage resulted in similar pollutant treatment for all

Quantifying Evaporation in a Permeable Pavement System

Science.gov (United States)

Studies quantifying evaporation from permeable pavement systems are limited to a few laboratory studies and one field application. This research quantifies evaporation for a larger-scale field application by measuring the water balance from lined permeable pavement sections. Th...

Metabolism distribution and transfer of tritium in pregnant mice after exposure to tritium water

International Nuclear Information System (INIS)

Lu Huimin; Zhou Xiangyan; Li Li; Zhang Zhixing

1993-01-01

Tritium water with three kind of different dose was singly injected intraperitoneally to pregnant mice in various time. The tritium concentration in the tissues from mother mice were measured on the 3.5 days after mother mice parturition. Dose rates in baby mice were estimated, as well as the transfer coefficient of tritium from mother mice to baby mice was calculated based on the tritium concentrations. The results of the experiment showed that tritium was almost uniformly distributed among the tissues after exposure to tritiated water at three experimental groups. However, it was found that relative concentrations of tritium in the baby mice tissues were consistently higher than that in mother mice tissues for three experimental groups. The relative concentration of tritium in the tissues was not affected by the different dose but developing on the exposure time. The results of radiation dose rates from baby mice estimation at the end of exposure showed that the higher radiation dose rates was found in the mice exposed to tritiated water during 7.5 days. The transfer coefficient of tritium from mother mice into baby mice was almost no different among the three radiation dose groups. The highest transfer coefficient was observed in mother mice exposed to tritiated baby mice was almost no different among the three radiation dose groups. The highest coefficient was observed in mother mice exposed to tritiated water during 16.5 days, however it was not found that transfer coefficient were higher in the mother mice exposed to tritiated water during 11.5 days than that of 7.5 days

Preliminary study of soil permeability properties using principal component analysis

Science.gov (United States)

Yulianti, M.; Sudriani, Y.; Rustini, H. A.

2018-02-01

Soil permeability measurement is undoubtedly important in carrying out soil-water research such as rainfall-runoff modelling, irrigation water distribution systems, etc. It is also known that acquiring reliable soil permeability data is rather laborious, time-consuming, and costly. Therefore, it is desirable to develop the prediction model. Several studies of empirical equations for predicting permeability have been undertaken by many researchers. These studies derived the models from areas which soil characteristics are different from Indonesian soil, which suggest a possibility that these permeability models are site-specific. The purpose of this study is to identify which soil parameters correspond strongly to soil permeability and propose a preliminary model for permeability prediction. Principal component analysis (PCA) was applied to 16 parameters analysed from 37 sites consist of 91 samples obtained from Batanghari Watershed. Findings indicated five variables that have strong correlation with soil permeability, and we recommend a preliminary permeability model, which is potential for further development.

Tritiated Water Interaction with Stainless Steel

International Nuclear Information System (INIS)

Glen R. Longhurst

2007-01-01

Experiments conducted to study tritium permeation of stainless steel at ambient and elevated temperatures revealed that HT converts relatively quickly to HTO. Further, the HTO partial pressure contributes essentially equally with elemental tritium gas in driving permeation through the stainless steel. Such permeation appears to be due to dissociation of the water molecule on the hot stainless steel surface. There is an equilibrium concentration of HTO vapor above adsorbed gas on the walls of the experimental apparatus evident from freezing transients. The uptake process of tritium from the carrier gas involves both surface adsorption and isotopic exchange with surface bound water

Conceptual design and optimization for JET water detritiation system cryo-distillation facility

International Nuclear Information System (INIS)

Lefebvre, X.; Hollingsworth, A.; Parracho, A.; Dalgliesh, P.; Butler, B.; Smith, R.

2015-01-01

The aim of the Exhaust Detritiation System (EDS) of the JET Active Gas Handling System (AGHS) is to convert all Q-based species (Q 2 , Q-hydrocarbons) into Q 2 O (Q being indifferently H, D or T) which is then trapped on molecular sieve beds (MSB). Regenerating the saturated MSBs leads to the production of tritiated water which is stored in Briggs drums. An alternative disposal solution to offsite shipping, is to process the tritiated water onsite via the implementation of a Water Detritiation System (WDS) based, in part, on the combination of an electrolyser and a cryo-distillation (CD) facility. The CD system will separate a Q 2 mixture into a de-tritiated hydrogen stream for safe release and a tritiated stream for further processing on existing AGHS subsystems. A sensitivity study of the Souers' model using the simulation program ProSimPlus (edited by ProSim S.A.) has then been undertaken in order to perform an optimised dimensioning of the cryo-distillation system in terms of available cooling technologies, cost of investment, cost of operations, process performance and safety. (authors)

Conceptual design and optimization for JET water detritiation system cryo-distillation facility

Energy Technology Data Exchange (ETDEWEB)

Lefebvre, X.; Hollingsworth, A.; Parracho, A.; Dalgliesh, P.; Butler, B.; Smith, R. [JET-EFDA, Culham Science Center, Abingdon, Oxon (United Kingdom)

2015-03-15

The aim of the Exhaust Detritiation System (EDS) of the JET Active Gas Handling System (AGHS) is to convert all Q-based species (Q{sub 2}, Q-hydrocarbons) into Q{sub 2}O (Q being indifferently H, D or T) which is then trapped on molecular sieve beds (MSB). Regenerating the saturated MSBs leads to the production of tritiated water which is stored in Briggs drums. An alternative disposal solution to offsite shipping, is to process the tritiated water onsite via the implementation of a Water Detritiation System (WDS) based, in part, on the combination of an electrolyser and a cryo-distillation (CD) facility. The CD system will separate a Q{sub 2} mixture into a de-tritiated hydrogen stream for safe release and a tritiated stream for further processing on existing AGHS subsystems. A sensitivity study of the Souers' model using the simulation program ProSimPlus (edited by ProSim S.A.) has then been undertaken in order to perform an optimised dimensioning of the cryo-distillation system in terms of available cooling technologies, cost of investment, cost of operations, process performance and safety. (authors)

Effect of CH4 on the CO2 breakthrough pressure and permeability of partially saturated low-permeability sandstone in the Ordos Basin, China

Science.gov (United States)

Zhao, Yan; Yu, Qingchun

2018-01-01

The behavior of CO2 that coexists with CH4 and the effect of CH4 on the CO2 stream need to be deeply analyzed and studied, especially in the presence of water. Our previous studies investigated the breakthrough pressure and permeability of pure CO2 in five partially saturated low-permeability sandstone core samples from the Ordos Basin, and we concluded that rocks with a small pore size and low permeability show considerable sealing capacity even under unsaturated conditions. In this paper, we selected three of these samples for CO2-CH4 gas-mixture breakthrough experiments under various degrees of water saturation. The breakthrough experiments were performed by increasing the gas pressure step by step until breakthrough occurred. Then, the effluent gas mixture was collected for chromatographic partitioning analysis. The results indicate that CH4 significantly affects the breakthrough pressure and permeability of CO2. The presence of CH4 in the gas mixture increases the interfacial tension and, thus, the breakthrough pressure. Therefore, the injected gas mixture that contains the highest (lowest) mole fraction of CH4 results in the largest (smallest) breakthrough pressure. The permeability of the gas mixture is greater than that for pure CO2 because of CH4, and the effective permeability decreases with increased breakthrough pressure. Chromatographic partitioning of the effluent mixture gases indicates that CH4 breaks through ahead of CO2 as a result of its weaker solubility in water. Correlations are established between (1) the breakthrough pressure and water saturation, (2) the effective permeability and water saturation, (3) the breakthrough pressure and effective permeability, and (4) the mole fraction of CO2/CH4 in the effluent mixture gases and water saturation. These results deepen our understanding of the multi-phase flow behavior in the porous media under unsaturated conditions, which have implications for formulating emergency response plans for gas

Use of tritiated water as indicator of the water metabolism on normal and operate patients; Emploi de l'eau tritiee comme indicateur du metabolisme de l'eau chez les sujets normaux et operes

Energy Technology Data Exchange (ETDEWEB)

Fallot, P; Aeberhardt, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

Water disruptions are very frequent during the medical and surgical affections. In order to study the kinetics of the water exchanges as well as the determination of the total water of the body, we have chosen tritiated water as indicator. This work presents a rapid process, faithful and sensitive of dosage of the Tritium in the biologic liquids. This method has been applied to the survey of the intestinal absorption of water among normal subjects and during some medical and surgical affections. The exam of the experimental curves permitted to get information concerning the kinetics of water ingested as well as of data on the volume of total water of the human body and on the biologic period of the Tritium in the organism. (M.B.) [French] Les perturbations hydriques sont tres frequentes au cours des affections medicales et chirurgicales. Afin d'etudier la cinetique des echanges hydriques ainsi que la determination de l'eau totale du corps, nous avons choisit l'eau tritiee comme indicateur. Ce travail presente une methode rapide, fidele et sensible de dosage du Tritium dans les liquides biologiques. Cette methode a ete appliquee a l'etude de l'absorption intestinale de l'eau chez des sujets normaux et au cours de certaines affections medicales et chirurgicales. L'examen des courbes experimentales ont permis d'obtenir des renseignements concernant la cinetique de l'eau ingeree ainsi que des donnees sur le volume d'eau totale du corps humain et sur la periode biologique du Tritium dans l'organisme. (M.B.)

Reformulating sunscreen cosmetics with better water resistance and efficacy to inhibit trans-epidermal water loss in response to global warming and climate change

International Nuclear Information System (INIS)

Sucgang, Raymond J.; Manalili, Jenalyn; Mañago, Sarah; Janio, Jonick; Ching, Maricar; Moya, Esperanza; Cruz, Luzviminda

2015-01-01

Three inhouse developed skin care formulations and four commercial formulations were tried out on dermatomed porcine skins for wettability and emoliency. Surface applied skin care formulations are alleged to reduce transepidermal water loss (TEWL). Sunscreens/sunblocks absorb or reflect the sun’s ultraviolet (UV) radiation on skin exposed to sunlight and thus helps protect against sunburn. Measurements of water resistance of topical application are normally done using contact angle measurements and swimming pool immersion approaches. TEWL is measured using vapometers. None of the conventional methods directly measure TEWL and water wash out rates. In this study, the effectiveness of skin moisturizers to inhibit TEWL was tested using tritiated water as radioactive tracer on degreased porcine skins. Topical emollients were applied on the epidermises of the skins and the skins were mounted epidermis facing down. Tritiated water was dropped on the top side of the skins and tritium activity concentrations of the moisture that passed through were measured. A modified immersion method was also developed as a screening tool to identify water resistant formulations. Sunscreens labelled with tritiated water were applied on the skin surfaces. The skins were immersed in water (distilled and sea water were compared) and aliquots of the water were counted for tritium every hour for 3 hours. Hydrophobicities of the formulations were predicted by the amounts of tritium that leached out from the skins. (author)

Effect of temperature on sandstone permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Kjøller, Claus

Hot water injection in geothermal sandstone aquifers is considered for seasonal energy storage in Denmark. However, an increase in the aquifer temperature might reduce permeability, and thereby increase production costs. An understanding of the factors that control permeability is required in order...... and the Klinkenberg procedure showed the expected correlation between the two measures, however, differences could be around one order of magnitude. In tight gas sandstones, permeability is often sensitive to net stress, which might change due to the pore pressure change in the Klinkenberg procedure. Besides...... affecting the Klinkenberg procedure, the combined effect of slip and changes in permeability would affect production during pressure depletion in tight gas sandstone reservoirs; therefore effects of gas slip and net stress on permeability were combined in a model based on the Klinkenberg equation. A lower...

Detection of semi-volatile organic compounds in permeable ...

Science.gov (United States)

Abstract The Edison Environmental Center (EEC) has a research and demonstration permeable parking lot comprised of three different permeable systems: permeable asphalt, porous concrete and interlocking concrete permeable pavers. Water quality and quantity analysis has been ongoing since January, 2010. This paper describes a subset of the water quality analysis, analysis of semivolatile organic compounds (SVOCs) to determine if hydrocarbons were in water infiltrated through the permeable surfaces. SVOCs were analyzed in samples collected from 11 dates over a 3 year period, from 2/8/2010 to 4/1/2013.Results are broadly divided into three categories: 42 chemicals were never detected; 12 chemicals (11 chemical test) were detected at a rate of less than 10% or less; and 22 chemicals were detected at a frequency of 10% or greater (ranging from 10% to 66.5% detections). Fundamental and exploratory statistical analyses were performed on these latter analyses results by grouping results by surface type. The statistical analyses were limited due to low frequency of detections and dilutions of samples which impacted detection limits. The infiltrate data through three permeable surfaces were analyzed as non-parametric data by the Kaplan-Meier estimation method for fundamental statistics; there were some statistically observable difference in concentration between pavement types when using Tarone-Ware Comparison Hypothesis Test. Additionally Spearman Rank order non-parame

Achieving high permeability and enhanced selectivity for Angstrom-scale separations using artificial water channel membranes.

Science.gov (United States)

Shen, Yue-Xiao; Song, Woochul C; Barden, D Ryan; Ren, Tingwei; Lang, Chao; Feroz, Hasin; Henderson, Codey B; Saboe, Patrick O; Tsai, Daniel; Yan, Hengjing; Butler, Peter J; Bazan, Guillermo C; Phillip, William A; Hickey, Robert J; Cremer, Paul S; Vashisth, Harish; Kumar, Manish

2018-06-12

Synthetic polymer membranes, critical to diverse energy-efficient separations, are subject to permeability-selectivity trade-offs that decrease their overall efficacy. These trade-offs are due to structural variations (e.g., broad pore size distributions) in both nonporous membranes used for Angstrom-scale separations and porous membranes used for nano to micron-scale separations. Biological membranes utilize well-defined Angstrom-scale pores to provide exceptional transport properties and can be used as inspiration to overcome this trade-off. Here, we present a comprehensive demonstration of such a bioinspired approach based on pillar[5]arene artificial water channels, resulting in artificial water channel-based block copolymer membranes. These membranes have a sharp selectivity profile with a molecular weight cutoff of ~ 500 Da, a size range challenging to achieve with current membranes, while achieving a large improvement in permeability (~65 L m -2  h -1  bar -1  compared with 4-7 L m -2  h -1  bar -1 ) over similarly rated commercial membranes.

Extravascular lung water and the pulmonary vascular permeability index may improve the definition of ARDS.

Science.gov (United States)

Perel, Azriel

2013-01-24

The recent Berlin definition has made some improvements in the older definition of acute respiratory distress syndrome (ARDS), although the concepts and components of the definition remained largely unchanged. In an effort to improve both predictive and face validity, the Berlin panel has examined a number of additional measures that may reflect increased pulmonary vascular permeability, including extravascular lung water. The panel concluded that although extravascular lung water has improved face validity and higher values are associated with mortality, it is infeasible to mandate on the basis of availability and the fact that it does not distinguish between hydrostatic and inflammatory pulmonary edema. However, the results of a multi-institutional study that appeared in the previous issue of Critical Care show that this latter reservation may not necessarily be true. By using extravascular lung water and the pulmonary vascular permeability index, both of which are derived from transpulmonary thermodilution, the authors could successfully differentiate between patients with ARDS and other patients in respiratory failure due to either cardiogenic edema or pleural effusion with atelectasis. This commentary discusses the merits and limitations of this study in view of the potential improvement that transpulmonary thermodilution may bring to the definition of ARDS.

Permeability Tests on Eastern Scheldt Sand

DEFF Research Database (Denmark)

Jakobsen, Kim Parsberg

on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Eastern Scheldt Sand. The permeability is determined by use of a falling head apparatus. Finally the test results are briefly summarised and a relationship between......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...

Tritiated uracil, tritiated thymidine, and bromodeoxyuridine induced mutations in eucaryotic cells

International Nuclear Information System (INIS)

Burki, H.J.; Moustacchi, E.; Cleaver, J.E.

1979-02-01

The induction of gene conversion at the ARG-4 locus in strain BZ34 of Saccharomyces cerevisiae was examined after the cells incorporated y- 3 H uracil under optimum growth conditions for 16 hours, and then received damage at 4 0 C from tritium decays at very low dose rates of 1.4 to 27.6 tritium decays per hour. The results were compared to the results of gene conversion induced by 60 Co. The induction of resistance to 6TG in Chinese hamster ovary (CHO) cells has been studied after incorporation of 3 H-methyl thymidine, 6- 3 H-thymidine, and bromodeoxyuridine under several experimental conditions. The induction of mutations by incorporated 6- 3 H-thymidine is about three times as effective as the induction of mutations by tritiated-methyl thymidine. These results suggest that the determination of the RBE for tritium decays in model eucaryotic systems like yeast and cultured Chinese hamster cells will be influenced by the precise experimental conditions employed. In particular, experiments with mammalian cells will be affected by hot times for mutagenesis in the cell cycle and hot positions within the DNA in the nucleus, and also by the position of tritium decay within the DNA-incorporated molecule

Water metabolism and modification of tritium excretion in the rat

International Nuclear Information System (INIS)

Ichimasa, Y.; Akita, Y.

1982-01-01

1. The intake and excretion of tritium were studied in rats exposed to tritiated water vapor. The metabolism of tritium was also investigated in rats given single administrations of tritiated water and in rats given daily administrations (per os or i.p.). The results were essentially in accord with those reported previously. 2. Amounts of drinking water consumed and urine excreted by rats drinking water with 0.15% saccharin were 1.5 to 2 times higher than in rats drinking tap water. The tritium activity in various tissues of rats drinking water with 0.15% saccharin decreased to about half of that of rats drinking tap water. A similar tendency was observed also in rats drinking beer. The diuretic agent sodium acetazolamide also enhanced the urinary excretion of tritium. (author)

Cholesterol effect on water permeability through DPPC and PSM lipid bilayers: a molecular dynamics study.

Science.gov (United States)

Saito, Hiroaki; Shinoda, Wataru

2011-12-29

Water permeability of two different lipid bilayers of dipalmitoylphosphatidylcholine (DPPC) and palmitoylsphingomyelin (PSM) in the absence and presence of cholesterol (0-50 mol %) have been studied by molecular dynamics simulations to elucidate the molecular mechanism of the reduction in water leakage across the membranes by the addition of cholesterol. An enhanced free energy barrier was observed in these membranes with increased cholesterol concentration, and this was explained by the reduced cavity density around the cholesterol in the hydrophobic membrane core. There was an increase of trans conformers in the hydrophobic lipid chains adjacent to the cholesterol, which reduced the cavity density. The enhanced free energy barrier was found to be the main reason to reduce the water permeability with increased cholesterol concentration. At low cholesterol concentrations the PSM bilayer exhibited a higher free energy barrier than the DPPC bilayer for water permeation, while at greater than 30 mol % of cholesterol the difference became minor. This tendency for the PSM and DPPC bilayers to resemble each other at higher cholesterol concentrations was similar to commonly observed trends in several structural properties, such as order parameters, cross-sectional area per molecule, and cavity density profiles in the hydrophobic regions of bilayer membranes. These results demonstrate that DPPC and PSM bilayers with high cholesterol contents possess similar physical properties, which suggests that the solubility of cholesterol in these lipid bilayers has importance for an understanding of multicomponent lipid membranes with cholesterol. © 2011 American Chemical Society

Theoretical Insight Into the Empirical Tortuosity-Connectivity Factor in the Burdine-Brooks-Corey Water Relative Permeability Model

Science.gov (United States)

Ghanbarian, Behzad; Ioannidis, Marios A.; Hunt, Allen G.

2017-12-01

A model commonly applied to the estimation of water relative permeability krw in porous media is the Burdine-Brooks-Corey model, which relies on a simplified picture of pores as a bundle of noninterconnected capillary tubes. In this model, the empirical tortuosity-connectivity factor is assumed to be a power law function of effective saturation with an exponent (μ) commonly set equal to 2 in the literature. Invoking critical path analysis and using percolation theory, we relate the tortuosity-connectivity exponent μ to the critical scaling exponent t of percolation that characterizes the power law behavior of the saturation-dependent electrical conductivity of porous media. We also discuss the cause of the nonuniversality of μ in terms of the nonuniversality of t and compare model estimations with water relative permeability from experiments. The comparison supports determining μ from the electrical conductivity scaling exponent t, but also highlights limitations of the model.

Effect of temperature and relative humidity on the water vapour permeability and mechanical properties of cassava starch and soy protein concentrate based edible films.

Science.gov (United States)

Chinma, C E; Ariahu, C C; Alakali, J S

2015-04-01

The effect of temperature and relative humidity on the water vapour permeability (WVP) and mechanical properties of cassava starch and soy protein concentrate (SPC) based edible films containing 20 % glycerol level were studied. Tensile strength and elastic modulus of edible films increased with increase in temperature and decreased with increase in relative humidity, while elongation at break decreased. Water vapour permeability of the films increased (2.6-4.3 g.mm/m(2).day.kPa) with increase in temperature and relative humidity. The temperature dependence of water vapour permeation of cassava starch-soy protein concentrate films followed Arrhenius relationship. Activation energy (Ea) of water vapour permeation of cassava starch-soy protein concentrate edible films ranged from 1.9 to 5.3 kJ/mol (R (2)  ≥ 0.93) and increased with increase in SPC addition. The Ea values were lower for the bio-films than for polyvinylidene chloride, polypropylene and polyethylene which are an indication of low water vapour permeability of the developed biofilms compared to those synthetic films.

Distribution of tritium in the different organs of calves and pigs after ingestion of various tritiated feeds

International Nuclear Information System (INIS)

Kirchmann, R.; Charles, P.; Bruwaene, R. van; Remy, J.; Koch, G.; Hoek, J. van den

1978-01-01

The studies reported here are related to the distribution of tritium in the organs of farm animals contaminated in various ways. Two young male calves ingested tritiated milk; the daily intake of 3 H-organic form was about 15 μCi for each calf and the total activity ingested until the sacrifice was 482 μCi. Three male pigs from the same litter and about 7 weeks old were used for each experiment of the administration of tritium under different forms. It was verified that the chemical form of 3 H present in the food is of great importance for the incorporation of 3 H in the organic matter of the animal organs. The total incorporation increases by a factor 5.6 when 3 H is ingested as tritiated milkpowder by pigs as compared to HTO and with a factor 15 for calves. When tritiated potatoes were ingested by pigs a factor 15.6 was found. The transfer of 3 H from HTO and milk feed ingested in the organic fraction of organs is lower for pig than for calf. (Auth.)

Comparison of tritiated and iodinated tracers in the radioimmunoassay of progesterone in cow milk

Energy Technology Data Exchange (ETDEWEB)

Allen, R M; Redshaw, M R [Hoechst Pharmaceuticals Research Ltd., Milton Keynes (UK); Holdsworth, R [Milk Marketing Board, Worcester (UK). Veterinary Research Unit

1980-01-01

Progesterone levels in the milk of cows were determined by two radioimmunoassay methods. Excellent correlation (r = 0.95) was found between the method using an iodinated radioligand and that using a conventional tritiated tracer.

Binding of tritiated corticosterone in brain sections of adrenalectomized rat

International Nuclear Information System (INIS)

Sarrieau, A.; Vial, M.; Dussaillant, M.; Rostene, W.; Philibert, P.

1983-01-01

A new technique which permits to study the specific binding of tritiated corticosterone in brain sections of adrenalectomized rats is described. Under these conditions, the specific binding of the glucocorticoid represents 60 to 70% of the initial binding. The apparent dissociation constant and the number of binding sites, determined by Scatchard analysis, are in the range of 10 -8 M and 100 fmoles/mg of protein respectively [fr

Seed Anatomy and Water Uptake in Relation to Seed Dormancy in Opuntia tomentosa (Cactaceae, Opuntioideae)

Science.gov (United States)

Orozco-Segovia, A.; Márquez-Guzmán, J.; Sánchez-Coronado, M. E.; Gamboa de Buen, A.; Baskin, J. M.; Baskin, C. C.

2007-01-01

Background and Aims There is considerable confusion in the literature concerning impermeability of seeds with ‘hard’ seed coats, because the ability to take up (imbibe) water has not been tested in most of them. Seeds of Opuntia tomentosa were reported recently to have a water-impermeable seed coat sensu lato (i.e. physical dormancy), in combination with physiological dormancy. However, physical dormancy is not known to occur in Cactaceae. Therefore, the aim of this study was to determine if seeds of O. tomentosa are water-permeable or water-impermeable, i.e. if they have physical dormancy. Methods The micromorphology of the seed coat and associated structures were characterized by SEM and light microscopy. Permeability of the seed-covering layers was assessed by an increase in mass of seeds on a wet substrate and by dye-tracking and uptake of tritiated water by intact versus scarified seeds. Key Results A germination valve and a water channel are formed in the hilum–micropyle region during dehydration and ageing in seeds of O. tomentosa. The funicular envelope undoubtedly plays a role in germination of Opuntia seeds via restriction of water uptake and mechanical resistance to expansion of the embryo. However, seeds do not exhibit any of three features characteristic of those with physical dormancy. Thus, they do not have a water-impermeable layer(s) of palisade cells (macrosclereids) or a water gap sensu stricto and they imbibe water without the seed coat being disrupted. Conclusions Although dormancy in seeds of this species can be broken by scarification, they have physiological dormancy only. Further, based on information in the literature, it is concluded that it is unlikely that any species of Opuntia has physical dormancy. This is the first integrative study of the anatomy, dynamics of water uptake and dormancy in seeds of Cactaceae subfamily Opuntioideae. PMID:17298989

NMR studies of human blood cells in health and disease. I. Alterations of the plasma membrane water permeability of erythrocytes

International Nuclear Information System (INIS)

Katona, Eva; Doaga, I. O.; Radulet, Diana; Caplanusi, A.; Negreanu, Cezarina; Mihele, Denisa

1999-01-01

Alterations in pathological cases of the human erythrocyte membrane water permeability were investigated by using a Mn 2+ -doping 1 H nuclear magnetic resonance (NMR) technique. The temperature dependence of the apparent water diffusional exchange through erythrocyte membranes in chronic hepatitis, diabetes, dyslipidemia and essential hypertension was measured and compared to healthy controls. Using moderate manganese concentrations (9-18 mM) and Carr-Purcell-Meiboom-Gill pulse sequences with a large number of refocusing π pulses and short interpulse delay (100 μs) our values of the water exchange times (τ e ) across erythrocyte membranes, obtained within a 10 min time period following the moment of doping, were independent of the actual manganese concentration and the Arrhenius plot for water exchange was linear over the range of 22-42 deg C. A marked increase of the water exchange times values was observed in all studied disease states. In case of chronic hepatitis, diabetes and dyslipidemia the changes observed in transmembrane water exchange time were associated with significant increase in the apparent activation energy of the diffusional water permeability thus, pointing out alterations in the function of the erythrocyte water channel. (author)

NMR studies of human blood cells in health and disease. I. Alterations of the plasma membrane water permeability of erythrocytes

Energy Technology Data Exchange (ETDEWEB)

Katona, Eva; Doaga, I O; Radulet, Diana [Department of Biophysics, Carol Davila University of Medicine and Pharmaceutics, 8 Blvd. Eroilor Sanitari, POB 15-205, RO-76241 Bucharest (Romania); Caplanusi, A [Medical Biochemistry Department, Carol Davila University of Medicine and Pharmaceutics, 8 Blvd. Eroilor Sanitari, POB 15-205, RO-76241 Bucharest (Romania); Negreanu, Cezarina [Division of New Energy Conversion Methods, Institute of Research and Design for Thermoenergetic Equipment, ICPET-CERCETARE, Bucharest (Romania); Mihele, Denisa [Clinical Laboratory Department, Carol Davila University of Medicine and Pharmaceutics, 8 Blvd. Eroilor Sanitari, POB 15-205, RO-76241 Bucharest (Romania)

1999-07-01

Alterations in pathological cases of the human erythrocyte membrane water permeability were investigated by using a Mn{sup 2+}-doping {sup 1}H nuclear magnetic resonance (NMR) technique. The temperature dependence of the apparent water diffusional exchange through erythrocyte membranes in chronic hepatitis, diabetes, dyslipidemia and essential hypertension was measured and compared to healthy controls. Using moderate manganese concentrations (9-18 mM) and Carr-Purcell-Meiboom-Gill pulse sequences with a large number of refocusing {pi} pulses and short interpulse delay (100 {mu}s) our values of the water exchange times ({tau}{sub e}) across erythrocyte membranes, obtained within a 10 min time period following the moment of doping, were independent of the actual manganese concentration and the Arrhenius plot for water exchange was linear over the range of 22-42 deg C. A marked increase of the water exchange times values was observed in all studied disease states. In case of chronic hepatitis, diabetes and dyslipidemia the changes observed in transmembrane water exchange time were associated with significant increase in the apparent activation energy of the diffusional water permeability thus, pointing out alterations in the function of the erythrocyte water channel. (author)

Effects on evaporation rates from different water-permeable pavement designs.

Science.gov (United States)

Starke, P; Göbel, P; Coldewey, W G

2011-01-01

The urban water balance can be attenuated to the natural by water-permeable pavements (WPPs). Furthermore, WPPs have a 16% higher evaporation rate than impermeable pavements, which can lead to a better urban climate. Evaporation rates from pavements are influenced by the pavement surface and by the deeper layers. By a compared evaporation measurement between different WPP designs, the grain size distribution of the sub-base shows no influence on the evaporation rates in a significant way. On the contrary, a sub-base made of a twin-layer decreases the evaporation by 16% compared to a homogeneous sub-base. By a change in the colour of the paving stone, 19% higher evaporation rates could be achieved. A further comparison shows that the transpiration-effect of the grass in grass pavers increases the evaporation rates more than threefold to pervious concrete pavements. These high evapotranspiration rates can not be achieved with a pervious concrete paving stone. In spite of this, the broad field of application of the pervious concrete paving stone increases the importance in regard to the urban climate.

Comparative field permeability measurement of permeable pavements using ASTM C1701 and NCAT permeameter methods.

Science.gov (United States)

Li, Hui; Kayhanian, Masoud; Harvey, John T

2013-03-30

Fully permeable pavement is gradually gaining support as an alternative best management practice (BMP) for stormwater runoff management. As the use of these pavements increases, a definitive test method is needed to measure hydraulic performance and to evaluate clogging, both for performance studies and for assessment of permeability for construction quality assurance and maintenance needs assessment. Two of the most commonly used permeability measurement tests for porous asphalt and pervious concrete are the National Center for Asphalt Technology (NCAT) permeameter and ASTM C1701, respectively. This study was undertaken to compare measured values for both methods in the field on a variety of permeable pavements used in current practice. The field measurements were performed using six experimental section designs with different permeable pavement surface types including pervious concrete, porous asphalt and permeable interlocking concrete pavers. Multiple measurements were performed at five locations on each pavement test section. The results showed that: (i) silicone gel is a superior sealing material to prevent water leakage compared with conventional plumbing putty; (ii) both methods (NCAT and ASTM) can effectively be used to measure the permeability of all pavement types and the surface material type will not impact the measurement precision; (iii) the permeability values measured with the ASTM method were 50-90% (75% on average) lower than those measured with the NCAT method; (iv) the larger permeameter cylinder diameter used in the ASTM method improved the reliability and reduced the variability of the measured permeability. Copyright © 2013 Elsevier Ltd. All rights reserved.

Hybrid green permeable pave with hexagonal modular pavement systems

International Nuclear Information System (INIS)

Rashid, M A; Abustan, I; Hamzah, M O

2013-01-01

Modular permeable pavements are alternatives to the traditional impervious asphalt and concrete pavements. Pervious pore spaces in the surface allow for water to infiltrate into the pavement during rainfall events. As of their ability to allow water to quickly infiltrate through the surface, modular permeable pavements allow for reductions in runoff quantity and peak runoff rates. Even in areas where the underlying soil is not ideal for modular permeable pavements, the installation of under drains has still been shown to reflect these reductions. Modular permeable pavements have been regarded as an effective tool in helping with stormwater control. It also affects the water quality of stormwater runoff. Places using modular permeable pavement has been shown to cause a significant decrease in several heavy metal concentrations as well as suspended solids. Removal rates are dependent upon the material used for the pavers and sub-base material, as well as the surface void space. Most heavy metals are captured in the top layers of the void space fill media. Permeable pavements are now considered an effective BMP for reducing stormwater runoff volume and peak flow. This study examines the extent to which such combined pavement systems are capable of handling load from the vehicles. Experimental investigation were undertaken to quantify the compressive characteristics of the modular. Results shows impressive results of achieving high safety factor for daily life vehicles.

Method of preparation of tritiated benzene for measuring in hydrology low level tritium in a liquid scintillator

International Nuclear Information System (INIS)

Pichat, L.; Sharefkin, D.; Herbert, M.

1962-01-01

It is given a preliminary account of the preparation of tritiated benzene by decarboxylation of calcium mellitate (calcium benzene-hexa-carboxylate) at 500 deg C by an excess of tritiated barium or calcium hydroxide yield is 64-72 pour cent based on used calcium mellitate. Benzene obtained after a single distillation is free from seriously quenching impurities. It is obtained 10-15 g benzene per batch. It remains to determine the occurrence of an isotope effect during the reaction. Various improvements and modifications are still necessary to increase the size of the sample to be treated. (authors) [fr

Long-Term Groundwater Monitoring Optimization, Clare Water Supply Superfund Site, Permeable Reactive Barrier and Soil Remedy Areas, Clare, Michigan

Science.gov (United States)

This report contains a review of the long-term groundwater monitoring network for the Permeable Reactive Barrier (PRB) and Soil Remedy Areas at the Clare Water Supply Superfund Site in Clare, Michigan.

Methane Seep in Shallow-Water Permeable Sediment Harbors High Diversity of Anaerobic Methanotrophic Communities, Elba, Italy

Science.gov (United States)

Ruff, S. Emil; Kuhfuss, Hanna; Wegener, Gunter; Lott, Christian; Ramette, Alban; Wiedling, Johanna; Knittel, Katrin; Weber, Miriam

2016-01-01

The anaerobic oxidation of methane (AOM) is a key biogeochemical process regulating methane emission from marine sediments into the hydrosphere. AOM is largely mediated by consortia of anaerobic methanotrophic archaea (ANME) and sulfate-reducing bacteria (SRB), and has mainly been investigated in deep-sea sediments. Here we studied methane seepage at four spots located at 12 m water depth in coastal, organic carbon depleted permeable sands off the Island of Elba (Italy). We combined biogeochemical measurements, sequencing-based community analyses and in situ hybridization to investigate the microbial communities of this environment. Increased alkalinity, formation of free sulfide and nearly stoichiometric methane oxidation and sulfate reduction rates up to 200 nmol g-1 day-1 indicated the predominance of sulfate-coupled AOM. With up to 40 cm thickness the zones of AOM activity were unusually large and occurred in deeper sediment horizons (20–50 cm below seafloor) as compared to diffusion-dominated deep-sea seeps, which is likely caused by advective flow of pore water due to the shallow water depth and permeability of the sands. Hydrodynamic forces also may be responsible for the substantial phylogenetic and unprecedented morphological diversity of AOM consortia inhabiting these sands, including the clades ANME-1a/b, ANME-2a/b/c, ANME-3, and their partner bacteria SEEP-SRB1a and SEEP-SRB2. High microbial dispersal, the availability of diverse energy sources and high habitat heterogeneity might explain that the emission spots shared few microbial taxa, despite their physical proximity. Although the biogeochemistry of this shallow methane seep was very different to that of deep-sea seeps, their key functional taxa were very closely related, which supports the global dispersal of key taxa and underlines strong selection by methane as the predominant energy source. Mesophilic, methane-fueled ecosystems in shallow-water permeable sediments may comprise distinct

Methane Seep in Shallow-Water Permeable Sediment Harbors High Diversity of Anaerobic Methanotrophic Communities, Elba, Italy.

Science.gov (United States)

Ruff, S Emil; Kuhfuss, Hanna; Wegener, Gunter; Lott, Christian; Ramette, Alban; Wiedling, Johanna; Knittel, Katrin; Weber, Miriam

2016-01-01

The anaerobic oxidation of methane (AOM) is a key biogeochemical process regulating methane emission from marine sediments into the hydrosphere. AOM is largely mediated by consortia of anaerobic methanotrophic archaea (ANME) and sulfate-reducing bacteria (SRB), and has mainly been investigated in deep-sea sediments. Here we studied methane seepage at four spots located at 12 m water depth in coastal, organic carbon depleted permeable sands off the Island of Elba (Italy). We combined biogeochemical measurements, sequencing-based community analyses and in situ hybridization to investigate the microbial communities of this environment. Increased alkalinity, formation of free sulfide and nearly stoichiometric methane oxidation and sulfate reduction rates up to 200 nmol g(-1) day(-1) indicated the predominance of sulfate-coupled AOM. With up to 40 cm thickness the zones of AOM activity were unusually large and occurred in deeper sediment horizons (20-50 cm below seafloor) as compared to diffusion-dominated deep-sea seeps, which is likely caused by advective flow of pore water due to the shallow water depth and permeability of the sands. Hydrodynamic forces also may be responsible for the substantial phylogenetic and unprecedented morphological diversity of AOM consortia inhabiting these sands, including the clades ANME-1a/b, ANME-2a/b/c, ANME-3, and their partner bacteria SEEP-SRB1a and SEEP-SRB2. High microbial dispersal, the availability of diverse energy sources and high habitat heterogeneity might explain that the emission spots shared few microbial taxa, despite their physical proximity. Although the biogeochemistry of this shallow methane seep was very different to that of deep-sea seeps, their key functional taxa were very closely related, which supports the global dispersal of key taxa and underlines strong selection by methane as the predominant energy source. Mesophilic, methane-fueled ecosystems in shallow-water permeable sediments may comprise distinct

Estimation of permeability and permeability anisotropy in horizontal wells through numerical simulation of mud filtrate invasion

Energy Technology Data Exchange (ETDEWEB)

Pereira, Nelson [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Exploracao e Producao; Altman, Raphael; Rasmus, John; Oliveira, Jansen [Schlumberger Servicos de Petroleo Ltda., Rio de Janeiro, RJ (Brazil)

2008-07-01

This paper describes how permeability and permeability anisotropy is estimated in horizontal wells using LWD (logging-while-drilling) laterolog resistivity data. Laterolog-while-drilling resistivity passes of while-drilling and timelapse (while reaming) were used to capture the invasion process. Radial positions of water based mud invasion fronts were calculated from while-drilling and reaming resistivity data. The invasion process was then recreated by constructing forward models with a fully implicit, near-wellbore numerical simulation such that the invasion front at a given time was consistent with the position of the front predicted by resistivity inversions. The radial position of the invasion front was shown to be sensitive to formation permeability. The while-drilling environment provides a fertile scenario to investigate reservoir dynamic properties because mud cake integrity and growth is not fully developed which means that the position of the invasion front at a particular point in time is more sensitive to formation permeability. The estimation of dynamic formation properties in horizontal wells is of particular value in marginal fields and deep-water offshore developments where running wireline and obtaining core is not always feasible, and where the accuracy of reservoir models can reduce the risk in field development decisions. (author)

A relative permeability model to derive fractional-flow functions of water-alternating-gas and surfactant-alternating-gas foam core-floods

International Nuclear Information System (INIS)

Al-Mossawy, Mohammed Idrees; Demiral, Birol; Raja, D M Anwar

2013-01-01

Foam is used in enhanced oil recovery to improve the sweep efficiency by controlling the gas mobility. The surfactant-alternating-gas (SAG) foam process is used as an alternative to the water-alternating-gas (WAG) injection. In the WAG technique, the high mobility and the low density of the gas lead the gas to flow in channels through the high permeability zones of the reservoir and to rise to the top of the reservoir by gravity segregation. As a result, the sweep efficiency decreases and there will be more residual oil in the reservoir. The foam can trap the gas in liquid films and reduces the gas mobility. The fractional-flow method describes the physics of immiscible displacements in porous media. Finding the water fractional flow theoretically or experimentally as a function of the water saturation represents the heart of this method. The relative permeability function is the conventional way to derive the fractional-flow function. This study presents an improved relative permeability model to derive the fractional-flow functions for WAG and SAG foam core-floods. The SAG flow regimes are characterized into weak foam, strong foam without a shock front and strong foam with a shock front. (paper)

Process for selectivity lowering the water permeability of a crude oil deposit

Energy Technology Data Exchange (ETDEWEB)

Katser, M F

1966-10-20

In this process for selectively reducing the water permeability of oil-bearing formations, especially during waterflooding, an aqueous solution is injected into the producing well. This solution contains a hydrolyzed acryl amide polymer, polyacrylamide or a copolymer, the greater part of which is acrylamide and the smaller part a polymerizable monomer, e.g., vinyl alcohol, vinyl chloride, acrylonitrile, methacrylonitrile or vinyl acryl ether. About 0.5-67.0% of the carboxy amide groups of the acrylamide polymer are hydrolyzed to carboxilic groups. The concentration of the hydrolyzed acrylamide polymer in the solution is about 0.01-1.0%. (3 claims)

Study on Surface Permeability of Concrete under Immersion

OpenAIRE

Liu, Jun; Xing, Feng; Dong, Biqin; Ma, Hongyan; Pan, Dong

2014-01-01

In this paper, concrete specimens are immersed in ultrapure water, to study the evolutions of surface permeability, pore structure and paste microstructure following the prolonging of immersion period. According to the results, after 30-day immersion, the surface permeability of concrete becomes higher as compared with the value before immersion. However, further immersion makes the surface permeability decrease, so that the value measured after 150-day immersion is only half that measured af...

Tritium water as a marker for the measurement of body water turnover rates in desert livestock, rodent and bird species

International Nuclear Information System (INIS)

Khan, M.S.; Ghosh, P.K.; Bohra, R.C.

1990-01-01

Tritiated water has been used for estimating body water turnover rates (BWTRs) in desert livestock, rodent and birds. BWTRs in relation to adaption of these animal species to desert environment have been discussed. (author). 5 refs., 2 tabs

Permeability of commercial solvents through living human skin

DEFF Research Database (Denmark)

Ursin, C; Hansen, C M; Van Dyk, J W

1995-01-01

A procedure has been developed for measuring the steady state rate of permeation of commercial solvents through living human skin. To get the most consistent results, it was necessary with some solvents to normalize the solvent permeation rate of a given skin sample with its [3H]water permeation...... rate. For other solvents this was not necessary, so the un-normalized data were used. High [3H]water permeation rate also was used as a criterion for "defective" skin samples that gave erroneous permeability rates, especially for solvents having slow permeability. The linearity of the steady state data...... was characterized by calculation of the "percent error of the slope." The following permeability rates (g/m2h) of single solvents were measured: dimethyl sulfoxide (DMSO), 176; N-methyl-2-pyrrolidone, 171; dimethyl acetamide, 107; methyl ethyl ketone, 53; methylene chloride, 24; [3H]water, 14.8; ethanol, 11...

Auxin Does Not Alter the Permeability of Pea Segments to Tritium-labeled Water.

Science.gov (United States)

Dowler, M J; Rayle, D L

1974-02-01

The possibility of an auxin effect on the permeability of pea (Pisum sativum L. ev. Alaska) segments to tritium-labeled water has been investigated by three separate laboratories, and the combined results are presented. We were unable to obtain any indication of a rapid effect of indoleacetic acid on the efflux of (3)HHO when pea segments previously "loaded" for 90 minutes with (3)HHO were transferred to unlabeled aqueous medium with indoleacetic acid. We were able to confirm that segments pretreated with (3)HHO plus indoleacetic acid for 60 to 90 minutes can show an enhanced (3)HHO release as compared with minus indoleacetic acid controls. However, this phenomenon appears to be due to an increased uptake of (3)HHO during the prolonged indoleacetic acid pretreatment, and therefore we conclude that auxin does not alter the permeability of pea segments to (3)HHO in either short term or long term tests. We confirm previous reports that the uptake of (3)HHO in pea segments proceeds largely through the cut surfaces, and that the cuticle is a potent barrier to (3)HHO flux.

Nanoemulsions as self-emulsified drug delivery carriers for enhanced permeability of the poorly water-soluble selective β₁-adrenoreceptor blocker Talinolol.

Science.gov (United States)

Ghai, Damanjeet; Sinha, Vivek Ranjan

2012-07-01

To enhance the bioavailability of the poorly water-soluble drug talinolol, a self-nanoemulsifying drug delivery system (SNEDDS) comprising 5% (w/v) Brij-721 ethanolic solution (Smix), triacetin, and water, in the ratio of 40:20:40 (% w/w) was developed by constructing pseudo-ternary phase diagrams and evaluated for droplet size, polydispersity index, and surface morphology of nanoemulsions. The effect of nanodrug carriers on drug release and permeability was assessed using stripped porcine jejunum and everted rat gut sac method and compared with hydroalcoholic drug solution, oily solution, and conventional emulsion and suspension. The SNEDDS showed a significant (P water-soluble beta-blocker talinolol. Significant increase in drug release, permeability, and in vivo bioavailability were demonstrated as compared to standard drug suspension. Copyright © 2012 Elsevier Inc. All rights reserved.

Permeability Tests on Silkeborg Sand No. 0000

DEFF Research Database (Denmark)

Lund, Willy; Jakobsen, Kim Parsberg

on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Silkeborg Sand No. 0000. The permeability is determined by use of a falling head apparatus. The apparatus, test procedures and the analysis method are described......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...

Preparation for tritiated waste management of fusion facilities: Interim storage WAC

Energy Technology Data Exchange (ETDEWEB)

Decanis, C., E-mail: christelle.decanis@cea.fr [CEA, DEN, Centre de Cadarache, F-13108 Saint-Paul-lez-Durance (France); Canas, D. [CEA, DEN/DADN, Centre de Saclay, F-91191 Gif-sur-Yvette cedex (France); Derasse, F. [CEA, DEN, Centre de Cadarache, F-13108 Saint-Paul-lez-Durance (France); Pamela, J. [CEA, Agence ITER-France, F-13108 Saint-Paul-lez-Durance (France)

2016-11-01

Highlights: • Fusion devices including ITER will generate tritiated waste. • Interim storage is the reference solution offering an answer for all types of tritiated radwaste. • Interim storage is a buffer function in the process management and definition of the waste acceptance criteria (WAC) is a key milestone in the facility development cycle. • Defining WAC is a relevant way to identify ahead of time the studies to be launched and the required actions to converge on a detailed design for example material specific studies, required treatment, interfaces management, modelling and monitoring studies. - Abstract: Considering the high mobility of tritium through the package in which it is contained, the new 50-year storage concepts proposed by the French Alternative Energies and Atomic Energy Commission (CEA) currently provide a solution adapted to the management of waste with tritium concentrations higher than the accepted limits in the disposals. The 50-year intermediate storage corresponds to 4 tritium radioactive periods i.e., a tritium reduction by a factor 16. This paper details the approach implemented to define the waste acceptance criteria (WAC) for an interim storage facility that not only takes into account the specificity of tritium provided by the reference scheme for the management of tritiated waste in France, but also the producers’ needs, the safety analysis of the facility and Andra’s disposal requirements. This will lead to define a set of waste specifications that describe the generic criteria such as acceptable waste forms, general principles and specific issues, e.g. conditioning, radioactive content, tritium content, waste tracking system, and quality control. This approach is also a way to check in advance, during the design phase of the waste treatment chain, how the future waste could be integrated into the overall waste management routes and identify possible key points that need further investigations (design changes, selection

Determination of filtrations and permeability of an earth dam

International Nuclear Information System (INIS)

Gomez, H.R.; Baro, G.B.; Gillen, Ricardo.

1975-11-01

The aim of this work was to measure with the aid of a radioactive tracer the speed flow of the water filtrating from Sumampa Dam in northeastern Catamarca, while being in operation, and with these data determine if the actual permeability corresponds to the projected one. Iodine-131 was used as tracer and periodical samples were taken from the down stream water in order to determine its activity concentration. In previous perforations ionic interchange resines were used so as to measure simultaneously the fixed Iodine-131. The permeability of the dam was calculated from the obtained speed based on time-concentration curves and applying Darcy formulas for permeability. (author) [es

Study on Storm-Water Management of Grassed Swales and Permeable Pavement Based on SWMM

Directory of Open Access Journals (Sweden)

Jianguang Xie

2017-10-01

Full Text Available Grassed swales and permeable pavement that have greater permeable underlying surface relative to hard-pressing surface can cooperate with the city pipe network on participating in urban storm flood regulation. This paper took Nanshan village in Jiangsu Province as an example, the storm-water management model (SWMM was used to conceptualize the study area reasonably, and the low-impact development (LID model and the traditional development model were established in the region. Based on the storm-intensity equation, the simulation scene employed the Chicago hydrograph model to synthesize different rainfall scenes with different rainfall repetition periods, and then contrasted the storm-flood-management effect of the two models under the condition of using LID facilities. The results showed that when the rainfall repetition period ranged from 0.33a to 10a (a refers to the rainfall repetition period, the reduction rate of total runoff in the research area that adopted LID ranged from 100% to 27.5%, while the reduction rate of peak flow ranged from 100% to 15.9%, and when the values of unit area were the same, the combined system (permeable pavement + grassed swales worked more efficiently than the sum of the individuals in the reduction of total runoff and peak flow throughout. This research can provide technical support and theoretical basis for urban LID design.

Ammonia gas permeability of meat packaging materials.

Science.gov (United States)

Karim, Faris; Hijaz, Faraj; Kastner, Curtis L; Smith, J Scott

2011-03-01

Meat products are packaged in polymer films designed to protect the product from exterior contaminants such as light, humidity, and harmful chemicals. Unfortunately, there is almost no data on ammonia permeability of packaging films. We investigated ammonia permeability of common meat packaging films: low-density polyethylene (LDPE; 2.2 mil), multilayer polyolefin (MLP; 3 mil), and vacuum (V-PA/PE; 3 mil, 0.6 mil polyamide/2.4 mil polyethylene). The films were fabricated into 10 × 5 cm pouches and filled with 50 mL deionized water. Pouches were placed in a plexiglass enclosure in a freezer and exposed to 50, 100, 250, or 500 ppm ammonia gas for 6, 12, 24, and 48 h at -17 ± 3 °C and 21 ± 3 °C. At freezing temperatures, no ammonia residues were detected and no differences in pH were found in the water. At room temperature, ammonia levels and pH of the water increased significantly (P packaging materials have low ammonia permeability and protect meat products exposed to ammonia leaks during frozen storage.

Permeability Barrier Generation in the Martian Lithosphere

Science.gov (United States)

Schools, Joe; Montési, Laurent

2015-11-01

Permeability barriers develop when a magma produced in the interior of a planet rises into the cooler lithosphere and crystallizes more rapidly than the lithosphere can deform (Sparks and Parmentier, 1991). Crystallization products may then clog the porous network in which melt is propagating, reducing the permeability to almost zero, i.e., forming a permeability barrier. Subsequent melts cannot cross the barrier. Permeability barriers have been useful to explain variations in crustal thickness at mid-ocean ridges on Earth (Magde et al., 1997; Hebert and Montési, 2011; Montési et al., 2011). We explore here under what conditions permeability barriers may form on Mars.We use the MELTS thermodynamic calculator (Ghiorso and Sack, 1995; Ghiorso et al., 2002; Asimow et al., 2004) in conjunction with estimated Martian mantle compositions (Morgan and Anders, 1979; Wänke and Dreibus, 1994; Lodders and Fegley, 1997; Sanloup et al., 1999; Taylor 2013) to model the formation of permeability barriers in the lithosphere of Mars. In order to represent potential past and present conditions of Mars, we vary the lithospheric thickness, mantle potential temperature (heat flux), oxygen fugacity, and water content.Our results show that permeability layers can develop in the thermal boundary layer of the simulated Martian lithosphere if the mantle potential temperature is higher than ~1500°C. The various Martian mantle compositions yield barriers in the same locations, under matching variable conditions. There is no significant difference in barrier location over the range of accepted Martian oxygen fugacity values. Water content is the most significant influence on barrier development as it reduces the temperature of crystallization, allowing melt to rise further into the lithosphere. Our lower temperature and thicker lithosphere model runs, which are likely the most similar to modern Mars, show no permeability barrier generation. Losing the possibility of having a permeability

Compression characteristics and permeability of saturated Gaomiaozi ca-bentonite

International Nuclear Information System (INIS)

Sun Wenjing; Sun De'an; Fang Lei

2012-01-01

The compression characteristics and permeability of compacted Gaomiaozi Ca-bentonite saturated by the water uptake tests are studied by conducting a series of one-dimension compression tests. The permeability coefficient can be calculated by the Terzaghi's one-dimensional consolidation theory after the consolidation coefficient is obtained by the square root of time method. It is found that the compression curves of compacted specimens saturated by the water uptake tests tend to be consistent in the relatively high stress range. The compression indexes show a linear decrease with increasing dry density and the swelling index is a constant. The permeability coefficient decreases with increasing compression stress, and they show the linear relationship in double logarithmic coordinates. Meanwhile, the permeability coefficient shows a linear decrease with decreasing void ratio, which has no relationship with initial states, stress states and stress paths. The permeability coefficient k of GMZ Ca-bentonite at dry density Pd of 1.75 g/cm 3 can be calculated as 2.0 × 10 -11 cm/s by the linear relationship between Pd and log k. It is closed to the permeability coefficient of GMZ Ca-bentonite with the same dry density published in literature, which testifies that the method calculating the permeability coefficient is feasible from the consolidation coefficient obtained by the consolidation test. (authors)

Tritium removal from contaminated water via infrared laser multiple-photon dissociation

International Nuclear Information System (INIS)

Maienschein, J.L.; Magnotta, F.; Herman, I.P.; Aldridge, F.T.; Hsiao, P.

1983-01-01

Isotope separation by means of infrared-laser multiple-photon dissociation offers an efficient way to recover tritium from contaminated light or heavy water found in fission and fusion reactors. For tritium recovery from heavy water, chemical exchange of tritium into deuterated chloroform is followed by selective laser dissociation of tritiated chloroform and removal of the tritiated photoproduct, TCl. The single-step separation factor is at least 2700 and is probably greater than 5000. Here we present a description of the tritium recovery process, along with recent accomplishments in photochemical studies and engineering analysis of a recovery system

The Lack of Cytotoxic Effect and Radioadaptive Response in Splenocytes of Mice Exposed to Low Level Internal β-Particle Irradiation through Tritiated Drinking Water in Vivo

Directory of Open Access Journals (Sweden)

Matthew Flegal

2013-12-01

Full Text Available Health effects of tritium, a β-emitter and a by-product of the nuclear industry, is a subject of significant controversy. This mouse in vivo study was undertaken to monitor biological effects of low level tritium exposure. Mice were exposed to tritiated drinking water (HTO at 10 KBq/L, 1 MBq/L and 20 MBq/L concentrations for one month. The treatment did not result in a significant increase of apoptosis in splenocytes. To examine if this low level tritium exposure alters radiosensitivity, the extracted splenocytes were challenged in vitro with 2 Gy γ-radiation, and apoptotic responses at 1 and 24 h were measured. No alterations in the radiosensitivity were detected in cells from mice exposed to tritium compared to sham-treated mice. In contrast, low dose γ-irradiation at 20 or 100 mGy, resulted in a significant increase in resistance to apoptotic cell death after 2 Gy irradiation; an indication of the radioadaptive response. Overall, our data suggest that low concentrations of tritium given to mice as HTO in drinking water do not exert cytotoxic effect in splenocytes, nor do they change cellular sensitivity to additional high dose γ-radiation. The latter may be considered as the lack of a radioadaptive response, typically observed after low dose γ-irradiation.

Performances of Metal Concentrations from Three Permeable Pavement Infiltrates

Science.gov (United States)

The U.S. Environmental Protection Agency designed and constructed a 4000-m2 parking lot in Edison, New Jersey in 2009. The parking lot is surfaced with three permeable pavements: permeable interlocking concrete pavers, pervious concrete, and porous asphalt. Water sampling was con...

Frost Resistance and Permeability of Cement Stabilized Gravel used as Filling Material for Pearl-Chain Bridges

DEFF Research Database (Denmark)

Lund, Mia Schou Møller; Hansen, Kurt Kielsgaard; Hertz, Kristian Dahl

2014-01-01

several requirements on its moisture properties. In this paper the frost resistance, the liquid water permeability and the water vapour permeability of cement stabilized gravel are examined for two different cement contents. It is found that a small increase in cement content from 4% to 5% increases...... the 28-days compressive strength from 6.2 MPa to 12.3 MPa. The frost resistance of cement stabilized gravel with 5% cement content is better than for cement stabilized gravel with 4% cement content. The liquid water permeability coefficient and the water vapour permeability coefficient are significantly...

A study on the water permeability of concrete structures

International Nuclear Information System (INIS)

Loadsman, R.V.C.; Acres, D.H.; Stokes, C.J.; Wadeson, L.

1988-03-01

This report forms part of the DoE's research programme on the disposal of nuclear waste. The information available on the permeability of concrete and the effects of various factors on this value are reviewed. The effect of defects on the overall permeability of concrete structures is examined and the recorded performance of a range of existing concrete structures is considered with identification of some of the factors that are significant in practice. Deficiencies in the information available on this subject are identified and recommendations for further work are made including a list of structures suitable for future monitoring. (author)

Integrated petrophysical and reservoir characterization workflow to enhance permeability and water saturation prediction

Science.gov (United States)

Al-Amri, Meshal; Mahmoud, Mohamed; Elkatatny, Salaheldin; Al-Yousef, Hasan; Al-Ghamdi, Tariq

2017-07-01

Accurate estimation of permeability is essential in reservoir characterization and in determining fluid flow in porous media which greatly assists optimize the production of a field. Some of the permeability prediction techniques such as Porosity-Permeability transforms and recently artificial intelligence and neural networks are encouraging but still show moderate to good match to core data. This could be due to limitation to homogenous media while the knowledge about geology and heterogeneity is indirectly related or absent. The use of geological information from core description as in Lithofacies which includes digenetic information show a link to permeability when categorized into rock types exposed to similar depositional environment. The objective of this paper is to develop a robust combined workflow integrating geology and petrophysics and wireline logs in an extremely heterogeneous carbonate reservoir to accurately predict permeability. Permeability prediction is carried out using pattern recognition algorithm called multi-resolution graph-based clustering (MRGC). We will bench mark the prediction results with hard data from core and well test analysis. As a result, we showed how much better improvements are achieved in the permeability prediction when geology is integrated within the analysis. Finally, we use the predicted permeability as an input parameter in J-function and correct for uncertainties in saturation calculation produced by wireline logs using the classical Archie equation. Eventually, high level of confidence in hydrocarbon volumes estimation is reached when robust permeability and saturation height functions are estimated in presence of important geological details that are petrophysically meaningful.

Water quality requirements for sustaining aquifer storage and recovery operations in a low permeability fractured rock aquifer.

Science.gov (United States)

Page, Declan; Miotliński, Konrad; Dillon, Peter; Taylor, Russel; Wakelin, Steve; Levett, Kerry; Barry, Karen; Pavelic, Paul

2011-10-01

A changing climate and increasing urbanisation has driven interest in the use of aquifer storage and recovery (ASR) schemes as an environmental management tool to supplement conventional water resources. This study focuses on ASR with stormwater in a low permeability fractured rock aquifer and the selection of water treatment methods to prevent well clogging. In this study two different injection and recovery phases were trialed. In the first phase ~1380 m(3) of potable water was injected and recovered over four cycles. In the second phase ~3300 m(3) of treated stormwater was injected and ~2410 m(3) were subsequently recovered over three cycles. Due to the success of the potable water injection cycles, its water quality was used to set pre-treatment targets for harvested urban stormwater of ≤ 0.6 NTU turbidity, ≤ 1.7 mg/L dissolved organic carbon and ≤ 0.2 mg/L biodegradable dissolved organic carbon. A range of potential ASR pre-treatment options were subsequently evaluated resulting in the adoption of an ultrafiltration/granular activated carbon system to remove suspended solids and nutrients which cause physical and biological clogging. ASR cycle testing with potable water and treated stormwater demonstrated that urban stormwater containing variable turbidity (mean 5.5 NTU) and organic carbon (mean 8.3 mg/L) concentrations before treatment could be injected into a low transmissivity fractured rock aquifer and recovered for irrigation supplies. A small decline in permeability of the formation in the vicinity of the injection well was apparent even with high quality water that met turbidity and DOC but could not consistently achieve the BDOC criteria. Copyright © 2011 Elsevier Ltd. All rights reserved.

Methane seep in shallow-water permeable sediment harbors high diversity of anaerobic methanotrophic communities, Elba, Italy

Directory of Open Access Journals (Sweden)

S Emil Ruff

2016-03-01

Full Text Available The anaerobic oxidation of methane (AOM is a key biogeochemical process regulating methane emission from marine sediments into the hydrosphere. AOM is largely mediated by consortia of anaerobic methanotrophic archaea (ANME and sulfate-reducing bacteria (SRB, and has mainly been investigated in deep-sea sediments. Here we studied methane seepage at four spots located at 12 m water depth in coastal, organic-carbon depleted permeable sands off the Island of Elba (Italy. We combined biogeochemical measurements, sequencing-based community analyses and in situ hybridization to investigate the microbial communities of this environment. Increased alkalinity, formation of free sulfide and nearly stoichiometric methane oxidation and sulfate reduction rates up to 200 nmol g-1 day-1 indicated the predominance of sulfate-coupled AOM. With up to 40 cm thickness the zones of AOM activity were unusually large and occurred in deeper sediment horizons (20–50 cm below seafloor as compared to diffusion-dominated deep-sea seeps, which is likely caused by advective flow of pore water due to the shallow water depth and permeability of the sands. Hydrodynamic forces also may be responsible for the substantial phylogenetic and unprecedented morphological diversity of AOM consortia inhabiting these sands, including the clades ANME-1a/b, ANME-2a/b/c, ANME-3 and their partner bacteria SEEP-SRB1a and SEEP-SRB2. High microbial dispersal, the availability of diverse energy sources and high habitat heterogeneity might explain that the emission spots shared few microbial taxa, despite their physical proximity. Although the biogeochemistry of this shallow methane seep was very different to that of deep-sea seeps, their key functional taxa were very closely related, which supports the global dispersal of key taxa and underlines strong selection by methane as the predominant energy source. Mesophilic, methane-fueled ecosystems in shallow-water permeable sediments may comprise

Experimental Measurement of Relative Permeability Functions for Fuel Cell GDL Materials

KAUST Repository

Hussaini, Irfan; Wang, Chao-Yang

2009-01-01

Gas diffusion layer in PEM fuel cells plays a pivotal role in water management. Modeling of liquid water transport through the GDL relies on knowledge of relative permeability functions in the in-plane and through-plane directions. In the present work, air and water relative permeabilities are experimentally determined as functions of saturation for typical GDL materials such as Toray-060, -090, -120 carbon paper and E-Tek carbon cloth materials in their plain, untreated forms. Saturation is measured using an ex-situ gravimetric method. Absolute and relative permeability functions in the two directions of interest are presented. Significant departure from the generally assumed cubic function of saturation is observed. ©The Electrochemical Society.

Tritiated hydrogen gas storage systems for a fusion plant

International Nuclear Information System (INIS)

Bramy, W.; Hircq, B.; Peyrat, M.; Leger, D.

1992-01-01

This paper reports that USSI INGENIERIE has carried out a study financed by European Communities Commission concerning the NET/ITER project, on tritium Fuel Management and Storage systems of the International Thermonuclear Experimental Reactor. A processing block diagram for hydrogen isotopes represents all interfaces and possible links between these systems and tritiated gas mixtures flowing through the Fusion plant. Large quantities of hydrogen isotopes (up to several thousand moles of protium, deuterium and tritium) in gaseous form associated with torus fuelling and exhaust pellet injection, and neutral beam injection, must be stored and managed in such a plant

Water turnover in reindeer. Some environmental implications

International Nuclear Information System (INIS)

Cameron, R.D.; Luick, J.R.; White, R.G.

1982-01-01

The nutritional and climatic effects on water turnover (determined using tritiated water) in reindeer are described. At low ambient temperatures (ca. -20 0 C) water turnover is related to protein and mineral intake, which is reflected in the relations of faecal and urinary water to nitrogen and ash excretion via these avenues. As ambient temperature increases, respiratory water, faecal water and urine flow increase, resulting in an increase in water turnover

Study on the application of permeable reactive barriers for remediation of uranium mine pit water

International Nuclear Information System (INIS)

Li Na'na; Zhu Yucheng

2012-01-01

Permeable reactive barrier (PRB) is economical and convenient on in suit remediation of polluted groundwater. In this paper, according to characteristics of uranium mine pit water, laboratory-scale PRB reactors were designed with the mixture of valent iron, active carbon, hydrated lime and quartz sands as reaction media. The feasibility and effectiveness of treating uranium mine pit water by PRB were tested under 3 different proportions of contaminants through dynamic simulation tests, which came out the optimal proportion of contaminants. The result indicated that the remediation effect of reactor B was the best, whose average removal rate to U was up to 99%. The quality of effluent attained the relevant standards, which indicated that the PRB technology is a feasible method for the treatment of uranium mine pit water. (authors)

Optimum Mix for Pervious Geopolymer Concrete (GEOCRETE Based on Water Permeability and Compressive Strength

Directory of Open Access Journals (Sweden)

Abdulsalam Arafa Salaheddin

2017-01-01

Full Text Available The production of ordinary Portland cement (OPC consumes considerable natural resources and energy, and it also affects the emission of a significant quantity of CO2 in the atmosphere. This pervious geopolymer concrete study aims to explore an alternative binder without OPC. Pervious geopolymer concretes were prepared from fly ash (FA, sodium silicate (NaSiO3, sodium hydroxide (NaOH solution, and coarse aggregate (CA. The effects of pervious geopolymer concrete parameters that affect water permeability and compressive strength are evaluated. The FA to CA ratios of 1:6, 1:7,1:8, and 1:9 by weight, CA sizes of 5–10, 10–14, and 14–20 mm, constant NaSiO3/NaOH ratio of 2.5, alkaline liquid to fly ash (AL/FA ratios of 0.4, 0.5, and 0.6, and NaOH concentrations of 8, 10, and 12 M were the pervious geopolymer concrete mix proportions. The curing temperature of 80 °C for 24 h was used. The results showed that a pervious geopolymer concrete with CA of 10 mm achieved water permeability of 2.3 cm/s and compressive strength of 20 MPa with AL/FA ratio of 0.5, NaOH concentration of 10 M, and FA:CA of 1:7. GEOCRETE is indicated to have better engineering properties than does pervious concrete that is made of ordinary Portland cement.

Tritium in the food chain. Intercomparison of model predictions of contamination in soil, crops, milk and beef after a short exposure to tritiated water vapour in air

Energy Technology Data Exchange (ETDEWEB)

Barry, P. [PJS Barry (Canada)] [and others

1996-09-01

Future fusion reactors using tritium as fuel will contain large inventories of the gas. The possibility that a significant fraction of an inventory may accidentally escape into the atmosphere from this and other potential sources such as tritium handling facilities and some fission reactors e g, PWRs has to be recognized and its potential impact on local human populations and biota assessed. Tritium gas is relatively inert chemically and of low radiotoxicity but it is readily oxidized by soil organisms to the mixed oxide, HTO or tritiated water. In this form it is highly mobile, strongly reactive biologically and much more toxic. Models of how tritiated water vapour is transported through the biosphere to foodstuffs important to man are essential components of such an assessment and it is important to test the models for their suitability when used for this purpose. To evaluate such models, access to experimental measurements made after actual releases are needed. There have however, been very few accidental releases of tritiated water to the atmosphere and the experimental findings of those that have occurred have been used to develop the models under test. Models must nevertheless be evaluated before their predictions can be used to decide the acceptability or otherwise of designing and operating major nuclear facilities. To fulfil this need a model intercomparison study was carried out for a hypothetical release scenario. The study described in this report is a contribution to the development of model evaluation procedures in general as well as a description of the results of applying these procedures to the particular case of models of HTO transport in the biosphere which are currently in use or being developed. The study involved eight modelers using seven models in as many countries. In the scenario farmland was exposed to 1E10 Bq d/m{sup 3} of HTO in air during 1 hour starting at midnight in one case and at 10.00 a.m. in the other, 30 days before harvest of

Tritium in the food chain. Intercomparison of model predictions of contamination in soil, crops, milk and beef after a short exposure to tritiated water vapour in air

International Nuclear Information System (INIS)

Barry, P.

1996-09-01

Future fusion reactors using tritium as fuel will contain large inventories of the gas. The possibility that a significant fraction of an inventory may accidentally escape into the atmosphere from this and other potential sources such as tritium handling facilities and some fission reactors e g, PWRs has to be recognized and its potential impact on local human populations and biota assessed. Tritium gas is relatively inert chemically and of low radiotoxicity but it is readily oxidized by soil organisms to the mixed oxide, HTO or tritiated water. In this form it is highly mobile, strongly reactive biologically and much more toxic. Models of how tritiated water vapour is transported through the biosphere to foodstuffs important to man are essential components of such an assessment and it is important to test the models for their suitability when used for this purpose. To evaluate such models, access to experimental measurements made after actual releases are needed. There have however, been very few accidental releases of tritiated water to the atmosphere and the experimental findings of those that have occurred have been used to develop the models under test. Models must nevertheless be evaluated before their predictions can be used to decide the acceptability or otherwise of designing and operating major nuclear facilities. To fulfil this need a model intercomparison study was carried out for a hypothetical release scenario. The study described in this report is a contribution to the development of model evaluation procedures in general as well as a description of the results of applying these procedures to the particular case of models of HTO transport in the biosphere which are currently in use or being developed. The study involved eight modelers using seven models in as many countries. In the scenario farmland was exposed to 1E10 Bq d/m 3 of HTO in air during 1 hour starting at midnight in one case and at 10.00 a.m. in the other, 30 days before harvest of crops

Regulation of Aquaporin Z osmotic permeability in ABA tri-block copolymer

Directory of Open Access Journals (Sweden)

Wenyuan Xie

2015-08-01

Full Text Available Aquaporins are transmembrane water channel proteins present in biological plasma membranes that aid in biological water filtration processes by transporting water molecules through at high speeds, while selectively blocking out other kinds of solutes. Aquaporin Z incorporated biomimetic membranes are envisaged to overcome the problem of high pressure needed, and holds great potential for use in water purification processes, giving high flux while keeping energy consumption low. The functionality of aquaporin Z in terms of osmotic permeability might be regulated by factors such as pH, temperature, crosslinking and hydrophobic thickness of the reconstituted bilayers. Hence, we reconstituted aquaporin Z into vesicles that are made from a series of amphiphilic block copolymers PMOXA-PDMS-PMOXAs with various hydrophobic molecular weights. The osmotic permeability of aquaporin Z in these vesicles was determined through a stopped-flow spectroscopy. In addition, the temperature and pH value of the vesicle solutions were adjusted within wide ranges to investigate the regulation of osmotic permeability of aquaporin Z through external conditions. Our results show that aquaporin Z permeability was enhanced by hydrophobic mismatch. In addition, the water filtration mechanism of aquaporin Z is significantly affected by the concentration of H+ and OH- ions.

A fractal analytical model for the permeabilities of fibrous gas diffusion layer in proton exchange membrane fuel cells

International Nuclear Information System (INIS)

Xiao, Boqi; Fan, Jintu; Ding, Feng

2014-01-01

The study of water and gas transport through fibrous gas diffusion layer (GDL) is important to the optimization of proton exchange membrane fuel cells (PEMFCs). In this work, analytical models of dimensionless permeability, and water and gas relative permeabilities of fibrous GDL in PEMFCs are derived using fractal theory. In our models, the structure of fibrous GDL is characterized in terms of porosity, tortuosity fractal dimension (D T ), pore area fractal dimensions (d f ), water phase (d f,w ) and gas phase (d f,g ) fractal dimensions. The predicted dimensionless permeability, water and gas relative permeabilities based on the proposed models are in good agreement with experimental data and predictions of numerical simulations reported in the literature. The model reveals that, although water phase and gas phase fractal dimensions strongly depend on porosity, the water and gas relative permeabilities are independent of porosity and are a function of water saturation only. It is also shown that the dimensionless permeability decreases significantly with the increase of tortuosity fractal dimension. On the other hand, there is only a small decrease in the water and gas relative permeabilities when tortuosity fractal dimension increases. One advantage of the proposed analytical model is that it contains no empirical constant, which is normally required in past models

Bentonite Permeability at Elevated Temperature

Directory of Open Access Journals (Sweden)

Katherine A. Daniels

2017-01-01

Full Text Available Repository designs frequently favour geological disposal of radioactive waste with a backfill material occupying void space around the waste. The backfill material must tolerate the high temperatures produced by decaying radioactive waste to prevent its failure or degradation, leading to increased hydraulic conductivity and reduced sealing performance. The results of four experiments investigating the effect of temperature on the permeability of a bentonite backfill are presented. Bentonite is a clay commonly proposed as the backfill in repository designs because of its high swelling capacity and very low permeability. The experiments were conducted in two sets of purpose-built, temperature controlled apparatus, designed to simulate isotropic pressure and constant volume conditions within the testing range of 4–6 MPa average effective stress. The response of bentonite during thermal loading at temperatures up to 200 °C was investigated, extending the previously considered temperature range. The results provide details of bentonite’s intrinsic permeability, total stress, swelling pressure and porewater pressure during thermal cycles. We find that bentonite’s hydraulic properties are sensitive to thermal loading and the type of imposed boundary condition. However, the permeability change is not large and can mostly be accounted for by water viscosity changes. Thus, under 150 °C, temperature has a minimal impact on bentonite’s hydraulic permeability.

Chemical composition of ground water and the locations of permeable zones in the Yucca Mountain area, Nevada

International Nuclear Information System (INIS)

Benson, L.V.; Robison, J.H.; Blankennagel, R.K.; Ogard, A.E.

1983-01-01

Ten wells in the Yucca Mountain area of southern Nevada have been sampled for chemical analysis. Samples were obtained during pumping of water from the entire well bore (composite sample) and in one instance by pumping water from a single isolated interval in well UE-25b number 1. Sodium is the most abundant cation and bicarbonate the most abundant anion in all water samples. Although the general chemical compositions of individual samples are similar, there are significant differences in uncorrected carbon-14 age and in inorganic and stable-isotope composition. Flow surveys of seven wells performed using iodine-131 as a tracer indicate that ground-water production is usually from one or more discrete zones of permeability. 7 references, 12 figures, 1 table

Study on Surface Permeability of Concrete under Immersion.

Science.gov (United States)

Liu, Jun; Xing, Feng; Dong, Biqin; Ma, Hongyan; Pan, Dong

2014-01-28

In this paper, concrete specimens are immersed in ultrapure water, to study the evolutions of surface permeability, pore structure and paste microstructure following the prolonging of immersion period. According to the results, after 30-day immersion, the surface permeability of concrete becomes higher as compared with the value before immersion. However, further immersion makes the surface permeability decrease, so that the value measured after 150-day immersion is only half that measured after 30-day immersion. The early increase in surface permeability should be mainly attributed to the leaching of calcium hydroxide, while the later decrease to the refinement of pore structure due to hydration. The two effects work simultaneously and compete throughout the immersion period. The proposed mechanisms get support from microscopic measurements and observations.

Diagenetic effect on permeabilities of geothermal sandstone reservoirs

DEFF Research Database (Denmark)

Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

The Danish subsurface contains abundant sedimentary deposits, which can be utilized for geothermal heating. The Upper Triassic – Lower Jurassic continental-marine sandstones of the Gassum Formation has been utilised as a geothermal reservoir for the Thisted Geothermal Plant since 1984 extracting...... and permeability is caused by increased diagenetic changes of the sandstones due to increased burial depth and temperatures. Therefore, the highest water temperatures typically correspond with the lowest porosities and permeabilities. Especially the permeability is crucial for the performance of the geothermal......-line fractures. Continuous thin chlorite coatings results in less porosity- and permeability-reduction with burial than the general reduction with burial, unless carbonate cemented. Therefore, localities of sandstones characterized by these continuous chlorite coatings may represent fine geothermal reservoirs...

Effects of the combinations of caffeine with 137Cs-gamma rays or tritiated water on the proliferation and malignant transformation CHL-1 cells

International Nuclear Information System (INIS)

Zou Shuai; Wang Shoufang

1989-01-01

The effects of the combinations of caffeine with 137 Cs-gamma rays or tritiated water on the proliferation and malignant transformation in vitro in CHL-1 cells were observed in experiments. At the concentrations of caffeine from 1 mmol/L to 2 mmol/L, the dose ranges of 137 Cs-gamma rays from 0.837 Gy and to 2.51 Gy and of tritium-beta radiation from 0.837 Gy to 0.528 Gy, the cell proliferation of CHL-1 cells was found to be inbigited when cells were exposed to caffeine, gamma and beta radiations, respectively, as well as when they were exposed to various combinations of caffeine with the two latters. The degree of inhibition of cell proliferation was dependent upon the concentration of caffeine and on the doses of radiation. In the transformation experiments, cell malignant transformation rates for all treated groups were higher than that for contol group and the rates for irradiated plus caffeine-treated groups were higher than those for corresponding single-agent-treated ones. After the subcutaneous injection of transformed cells into irradiated mice, tumours in size of about 2 mm 3 were found in some animals and the tumour cells were identical with in-vitro-transformed CHL-1 cells histopathologically

Correlation of Water Quality Parameters with Metal Concentrations in Permeable Pavement Infiltrate

Science.gov (United States)

EPA constructed a 4,000-m2 parking lot for research and demonstration of three permeable pavements [permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA)] at the Edison Environmental Center in Edison, NJ in 2009. Infiltrate samples from e...

A computational assessment of the permeability and salt rejection of carbon nanotube membranes and their application to water desalination

Science.gov (United States)

Thomas, Michael; Corry, Ben

2016-01-01

Membranes made from nanomaterials such as nanotubes and graphene have been suggested to have a range of applications in water filtration and desalination, but determining their suitability for these purposes requires an accurate assessment of the properties of these novel materials. In this study, we use molecular dynamics simulations to determine the permeability and salt rejection capabilities for membranes incorporating carbon nanotubes (CNTs) at a range of pore sizes, pressures and concentrations. We include the influence of osmotic gradients and concentration build up and simulate at realistic pressures to improve the reliability of estimated membrane transport properties. We find that salt rejection is highly dependent on the applied hydrostatic pressure, meaning high rejection can be achieved with wider tubes than previously thought; while membrane permeability depends on salt concentration. The ideal size of the CNTs for desalination applications yielding high permeability and high salt rejection is found to be around 1.1 nm diameter. While there are limited energy gains to be achieved in using ultra-permeable CNT membranes in desalination by reverse osmosis, such membranes may allow for smaller plants to be built as is required when size or weight must be minimized. There are diminishing returns in further increasing membrane permeability, so efforts should focus on the fabrication of membranes containing narrow or functionalized CNTs that yield the desired rejection or selection properties rather than trying to optimize pore densities. PMID:26712639

The permeability of red blood cells to chloride, urea and water

DEFF Research Database (Denmark)

Brahm, Jesper

2013-01-01

This study extends permeability (P) data on chloride, urea and water in red blood cells (RBC), and concludes that the urea transporter (UT-B) does not transport water. P of chick, duck, Amphiuma means, dog and human RBC to (36)Cl(-), (14)C-urea and (3)H2O was determined under self....... Temperature dependence, as measured by apparent activation energy, EA, of PCl is 117.8 (duck), 74.9 (Amphiuma) and 89.6 kJ mol(-1) (dog). The EA of Purea is 69.6 (duck) and 53.3 kJ mol(-1) (Amphiuma), and that of Pd is 34.9 (duck) and 32.1 kJ mol(-1) (Amphiuma). The present and previous RBC studies indicate......-exchange conditions. At 25°C and pH 7.2-7.5, PCl is 0.94×10(-4)-2.15×10(-4) cm s(-1) for all RBC species at [Cl]=127-150 mmol l(-1). In chick and duck RBC, Purea is 0.84×10(-6) and 1.65×10(-6) cm s(-1), respectively, at [urea]=1-500 mmol l(-1). In Amphiuma, dog and human RBC, Purea is concentration dependent (1...

The permeability and consolidation of deep-sea sediments

International Nuclear Information System (INIS)

Schultheiss, P.J.; Gunn, D.E.

1985-01-01

This report presents permeability and consolidation data for a wide range of sediment types. Permeability is one of the two parameters which are needed to directly quantify pore water advection in deep sea sediments and which are being investigated in high-level radioactive waste study areas. While it is desirable that these parameters should be measured in situ it is argued that values of permeability can be measured sufficiently accurately in the laboratory from core samples. Consequently, an apparatus has been developed which enables sediment permeability to be measured at decreasing void ratios during a back-pressured consolidation test. Data presented in this report from over 60 samples have established the major differences in permeability between various sediment types and how permeability changes as a function of burial depth and void ratio. Samples from two study areas in the North Atlantic Ocean, King's Trough Flank (KTF) and Great Meteor East (GME), have been compared with samples of Red Clay (RC) obtained from the NW Pacific Ocean. Results are presented and discussed. (author)

Diffusion of Tritiated Water (HTO) and 22Na+-Ions through Non-Degraded Hardened Cement Pastes - II. Modelling Results

International Nuclear Information System (INIS)

Jakob, A.

2002-12-01

In this report, the procedure and the results of an inverse modelling study on the through-diffusion of tritiated water (HTO) and 2 2Na + -ions are presented using high-porous hardened cement pastes with a water/cement ratio of 1.3 in the first stage of the cement degradation. For the analysis two alternative models were applied: 1) a diffusion model where a possible sorption of the tracer was entirely neglected, and 2) a diffusion model with linear sorption. The analysis of the through-diffusion phase allowed extracting values for the effective diffusion coefficient (D e ) and the rock-capacity factor (α). Both models could fit the breakthrough curves equally well, and also mass-balance considerations did not allow to clearly preferring one of the two competing models to the other. But blind-predictions for tracer out-diffusion using the best-fit parameter values deduced from analysing the former through-diffusion phase gave a clear indication that linear sorption had to be included in the diffusion model. The extracted K d values for HTO are in excellent agreement with values from batch sorption experiments and are of the order of 0.8. 10 -3 m 3 /kg. Those for 2 2Na + are of the order of 1.0. 10 -3 m 3 /kg and are by a factor of two larger than values from batch sorption experiments. The values for the effective diffusion coefficients for HTO are of the order of (2-3).10 -1 0 m 2 /s, and those for sodium are roughly by a factor of two smaller than values for HTO. On the one hand, the observed tracer uptake could only partially be addressed to isotope exchange; the most obvious process which could account for the remaining part of the uptaken tracer mass is diffusion into a second type of porosity, the dead-end pores. On the other hand, the results and conclusions drawn are encouraging for future investigations; therefore no major deficiency concerning the applied equipment and the modelling methodology could be detected. In the report, however, some suggestions

Water absorption enhances the uptake of mannitol and decreases Cr-EDTA/mannitol permeability ratios in cat small intestine in situ

NARCIS (Netherlands)

Bijlsma, P. B.; Fihn, B. M.; Sjöqvist, A.; Groot, J. A.; Taminiau, J. A. J. M.; Jodal, M.

2002-01-01

Background: Recently, we hypothesized that mannitol absorption in human intestinal permeability tests is a reflection of small intestinal water absorption and is dependent mainly on the efficiency of the countercurrent multiplier in the villi. This may affect the outcome of clinical double-sugar

Experimental Study of Matrix Permeability of Gas Shale: An Application to CO2-Based Shale Fracturing

Directory of Open Access Journals (Sweden)

Chengpeng Zhang

2018-03-01

Full Text Available Because the limitations of water-based fracturing fluids restrict their fracturing efficiency and scope of application, liquid CO2 is regarded as a promising substitute, owing to its unique characteristics, including its greater environmental friendliness, shorter clean-up time, greater adsorption capacity than CH4 and less formation damage. Conversely, the disadvantage of high leak-off rate of CO2 fracturing due to its very low viscosity determines its applicability in gas shales with ultra-low permeability, accurate measurement of shale permeability to CO2 is therefore crucial to evaluate the appropriate injection rate and total consumption of CO2. The main purpose of this study is to accurately measure shale permeability to CO2 flow during hydraulic fracturing, and to compare the leak-off of CO2 and water fracturing. A series of permeability tests was conducted on cylindrical shale samples 38 mm in diameter and 19 mm long using water, CO2 in different phases and N2 considering multiple influencing factors. According to the experimental results, the apparent permeability of shale matrix to gaseous CO2 or N2 is greatly over-estimated compared with intrinsic permeability or that of liquid CO2 due to the Klinkenberg effect. This phenomenon explains that the permeability values measured under steady-state conditions are much higher than those under transient conditions. Supercritical CO2 with higher molecular kinetic energy has slightly higher permeability than liquid CO2. The leak-off rate of CO2 is an order of magnitude higher than that of water under the same injection conditions due to its lower viscosity. The significant decrease of shale permeability to gas after water flooding is due to the water block effect, and much longer clean-up time and deep water imbibition depth greatly impede the gas transport from the shale matrix to the created fractures. Therefore, it is necessary to substitute water-based fracturing fluids with liquid or super

Measurement of Tritium Activity in Plants by Ice Extraction Method

International Nuclear Information System (INIS)

Pelled, O.; Ovad, S.; Tubul, Y.; Tsroya, S.; Gonen, R.; Abraham, A.; Weinstein, M.; German, U.

2014-01-01

Tritium is produced primarily by interactions of cosmic rays with the atmosphere. However, nuclear installations may add significantly tritium to the surroundings, increasing its concentration. The main sources of tritium released by man are linked to the nuclear power cycle: nuclear power stations, nuclear fuel reprocessing plants or tritium production plants. Tritium is found in the environment mainly as tritiated water, in gaseous or liquid form (HTO, T2O), in the surrounding air and in soil. It accumulates in plants, which may use as a measure to the level of tritium concentration in the environment. The most common routes of tritium uptake from the environment in plants are from atmospheric humidity and by precipitation water which entered the soil. The fraction of tritium bound to the plant tissue is small compared to that present as tritiated water in the plant (from 0.06% to 0.3% for growing crops). The tritiated water uptake is through the roots, as tritiated water from the soil follows a pathway similar to that of ordinary water. As most tritium in plants consists of tritiated water, the measurements of only the tissue free water tritium concentration (as HTO or T2O) gives an accurate estimate of the tritium content in the plant. Analyzing free tritium in biological matrices usually requires using the freeze-drying method to extract the water from the sample, and then measure the water collected in a cold trap with a Liquid Scintillation Counter (LSC). The 'freeze-drying' occurs because of the sublimation of the frozen water inside the plant, that takes place when the temperature is beneath the triple point and the vapour pressure is low. In the temperature range of -5° to -10° C the mechanism that plants use to avoid freezing is drawing of water from the cell protoplasm into the intercellular spaces. Changes in cell membrane permeability allow water to leave the cell and enter the spaces between the cells where it freezes instead of freezing within the

Subzero water permeability parameters and optimal freezing rates for sperm cells of the southern platyfish, Xiphophorus maculatus.

Science.gov (United States)

Pinisetty, D; Huang, C; Dong, Q; Tiersch, T R; Devireddy, R V

2005-06-01

This study reports the subzero water transport characteristics (and empirically determined optimal rates for freezing) of sperm cells of live-bearing fishes of the genus Xiphophorus, specifically those of the southern platyfish Xiphophorus maculatus. These fishes are valuable models for biomedical research and are commercially raised as ornamental fish for use in aquariums. Water transport during freezing of X. maculatus sperm cell suspensions was obtained using a shape-independent differential scanning calorimeter technique in the presence of extracellular ice at a cooling rate of 20 degrees C/min in three different media: (1) Hanks' balanced salt solution (HBSS) without cryoprotective agents (CPAs); (2) HBSS with 14% (v/v) glycerol, and (3) HBSS with 10% (v/v) dimethyl sulfoxide (DMSO). The sperm cell was modeled as a cylinder with a length of 52.35 microm and a diameter of 0.66 microm with an osmotically inactive cell volume (Vb) of 0.6 V0, where V0 is the isotonic or initial cell volume. This translates to a surface area, SA to initial water volume, WV ratio of 15.15 microm(-1). By fitting a model of water transport to the experimentally determined volumetric shrinkage data, the best fit membrane permeability parameters (reference membrane permeability to water at 0 degrees C, Lpg or Lpg [cpa] and the activation energy, E(Lp) or E(Lp) [cpa]) were found to range from: Lpg or Lpg [cpa] = 0.0053-0.0093 microm/minatm; E(Lp) or E(Lp) [cpa] = 9.79-29.00 kcal/mol. By incorporating these membrane permeability parameters in a recently developed generic optimal cooling rate equation (optimal cooling rate, [Formula: see text] where the units of B(opt) are degrees C/min, E(Lp) or E(Lp) [cpa] are kcal/mol, L(pg) or L(pg) [cpa] are microm/minatm and SA/WV are microm(-1)), we determined the optimal rates of freezing X. maculatus sperm cells to be 28 degrees C/min (in HBSS), 47 degrees C/min (in HBSS+14% glycerol) and 36 degrees C/min (in HBSS+10% DMSO). Preliminary empirical

Study on the Permeability Characteristics of Polyurethane Soil Stabilizer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2017-01-01

Full Text Available A polymer material of polyurethane soil stabilizer (PSS is used to reinforce the sand. To understand the permeability characteristics of PSS reinforced sand, a series of reinforcement layer form test, single-hole permeability test, and porous permeability test of sand reinforced with PSS have been performed. Reinforcement mechanism is discussed with scanning electron microscope images. The results indicated that the permeability resistance of sand reinforced with polyurethane soil stabilizer is improved through the formation of reinforcement layer on the sand surface. The thickness and complete degree of the reinforcement layer increase with the increasing of curing time and PSS concentration. The water flow rate decreases with the increasing of curing time or PSS concentration. The permeability coefficient decreases with the increasing of curing time and PSS concentration and increases with the increasing of depth in specimen. PSS fills up the voids of sand and adsorbs on the surface of sand particle to reduce or block the flowing channels of water to improve the permeability resistance of sand. The results can be applied as the reference for chemical reinforcement sandy soil engineering, especially for surface protection of embankment, slope, and landfill.

Improving the performance of water desalination through ultra-permeable functionalized nanoporous graphene oxide membrane

Science.gov (United States)

Hosseini, Mostafa; Azamat, Jafar; Erfan-Niya, Hamid

2018-01-01

Molecular dynamics simulations were performed to investigate the water desalination performance of nanoporous graphene oxide (NPGO) membranes. The simulated systems consist of a NPGO as a membrane with a functionalized pore in its center immersed in an aqueous ionic solution and a graphene sheet as a barrier. The considered NPGO membranes are involved four types of pore with different size and chemistry. The results indicated that the NPGO membrane has effective efficiency in salt rejection as well as high performance in water flux. For all types of pore with the radius size of 2.9-4.5 Å, the NPGO shows salt rejection of >89%. Functional groups on the surface and edge of pores have a great effect on water flux. To precisely understand the effect of functional groups on the surface of nanostructured membranes, nanoporous graphene was simulated under the same condition for comparison. Hydrophilic groups on the surface make the NPGO as an ultra-permeable membrane. As a result, the obtained water flux for NPGO was about 77% greater than graphene. Also, it was found that the water flux of NPGO is 2-5 orders of magnitude greater than other existing reverse osmosis membranes. Therefore, the investigated systems can be recommended as a model for the water desalination.

Effect of tritiated compounds on sister-chromatid exchanges (SCE) in human lymphocytes in vitro

International Nuclear Information System (INIS)

Gong Manli; Rao Yongqing; Chen Guanying; Wu Weiwei; Zhao Zilan; Shen Lei

1990-01-01

Human lymphocytes treated in vitro with various activities of 3 H-TdR and 3 H-UdR were cultured to understand the effects of tritium on the cell cycle and the frequency of SCE. The results of these experiments indicated that both tritiated compounds make the frequency of SCE increase and the cell cycle delay. The frequency of SCE increased markedly with activity of 3 H. With respect to delaying cell cycle, 3 H-UdR was more effective than 3 H-TdR. The average frequencies of SCE for 3 H-UdR were higher than those for 3 H-TdR. With the exception of 3.7 x 10 3 Bq/mL group and differences between other 3 H-UdR groups and corresponding 3 H-TdR group were significant (t test, p < 0.01). These results suggest that tritiated compounds may have the effect on the cell proliferating rate. The cell proliferating rate index (PRI) seems to be related with the frequency of SCE: the higher the frequency of SCE, the lower the PRI is

Comparison of permeable pavement types : hydrology, design, installation, maintenance and cost.

Science.gov (United States)

2012-01-13

"WisDOTs regional storm water engineer for the Southeast Region is interested in developing a park-and-ride with : porous pavement, possibly with the PaveDrain brand of permeable block. Research was needed to determine how : well permeable pavemen...

Developments in permeable and low permeability barriers

International Nuclear Information System (INIS)

Jefferis, S.A.; Norris, G.H.; Thomas, A.O.

1997-01-01

The concept of the reactive treatment zone whereby pollutants are attenuated as they move along a pathway in the ground has enabled a re-thinking of many of the concepts of containment. In particular it offers the potential for the control of the flux from a contaminated area by controlling the contaminant concentration in the pathway(s) as well as or instead of using a low permeability barrier. The paper outlines the basic concepts of the reactive treatment zone and the use of permeable and low permeability reactive systems. The paper then gives a case history of the installation of a permeable barrier using an in-situ reaction chamber

Permeability of commercial solvents through living human skin

DEFF Research Database (Denmark)

Ursin, C; Hansen, C M; Van Dyk, J W

1995-01-01

A procedure has been developed for measuring the steady state rate of permeation of commercial solvents through living human skin. To get the most consistent results, it was necessary with some solvents to normalize the solvent permeation rate of a given skin sample with its [3H]water permeation...... rate. For other solvents this was not necessary, so the un-normalized data were used. High [3H]water permeation rate also was used as a criterion for "defective" skin samples that gave erroneous permeability rates, especially for solvents having slow permeability. The linearity of the steady state data...... of DMSO and octyl acetate were measured. No octyl acetate was detected and the permeability of DMSO was proportional to its mole fraction in the mixture. The effect of two hours of solvent exposure on the viability of skin (based on DNA synthesis) was measured and found to be very dependent on the solvent....

Oil recovery enhancement from fractured, low permeability reservoirs. [Carbonated Water

Energy Technology Data Exchange (ETDEWEB)

Poston, S.W.

1991-01-01

The results of the investigative efforts for this jointly funded DOE-State of Texas research project achieved during the 1990-1991 year may be summarized as follows: Geological Characterization - Detailed maps of the development and hierarchical nature the fracture system exhibited by Austin Chalk outcrops were prepared. The results of these efforts were directly applied to the development of production decline type curves applicable to a dual-fracture-matrix flow system. Analysis of production records obtained from Austin Chalk operators illustrated the utility of these type curves to determine relative fracture/matrix contributions and extent. Well-log response in Austin Chalk wells has been shown to be a reliable indicator of organic maturity. Shear-wave splitting concepts were used to estimate fracture orientations from Vertical Seismic Profile, VSP data. Several programs were written to facilitate analysis of the data. The results of these efforts indicated fractures could be detected with VSP seismic methods.Development of the EOR Imbibition Process - Laboratory displacement as well as Magnetic Resonance Imaging, MRI and Computed Tomography, CT imaging studies have shown the carbonated water-imbibition displacement process significantly accelerates and increases recovery from oil saturated, low permeability rocks.Field Tests - Two operators amenable to conducting a carbonated water flood test on an Austin Chalk well have been identified. Feasibility studies are presently underway.

Oil Recovery Enhancement from Fractured, Low Permeability Reservoirs. [Carbonated Water

Science.gov (United States)

Poston, S. W.

1991-01-01

The results of the investigative efforts for this jointly funded DOE-State of Texas research project achieved during the 1990-1991 year may be summarized as follows: Geological Characterization - Detailed maps of the development and hierarchical nature the fracture system exhibited by Austin Chalk outcrops were prepared. The results of these efforts were directly applied to the development of production decline type curves applicable to a dual-fracture-matrix flow system. Analysis of production records obtained from Austin Chalk operators illustrated the utility of these type curves to determine relative fracture/matrix contributions and extent. Well-log response in Austin Chalk wells has been shown to be a reliable indicator of organic maturity. Shear-wave splitting concepts were used to estimate fracture orientations from Vertical Seismic Profile, VSP data. Several programs were written to facilitate analysis of the data. The results of these efforts indicated fractures could be detected with VSP seismic methods. Development of the EOR Imbibition Process - Laboratory displacement as well as Magnetic Resonance Imaging, MRI and Computed Tomography, CT imaging studies have shown the carbonated water-imbibition displacement process significantly accelerates and increases recovery from oil saturated, low permeability rocks. Field Tests - Two operators amenable to conducting a carbonated water flood test on an Austin Chalk well have been identified. Feasibility studies are presently underway.

Model for tritiated water transport in soil

International Nuclear Information System (INIS)

Galeriu, D.; Paunescu, N.

1999-01-01

Chemical forms of tritium released from nuclear facilities are mostly water (HTO) and hydrogen (HT, TT). Elemental tritium is inert in vegetation and superior animals, but the microorganisms from soil oxidize HT to HTO. After an atmospheric HT emission, in short time an equivalent quantity of HTO is re-emitted from soil. In the vicinity of a tritium source the spatial and temporary distribution of HTO is dependent on the chemical form of tritium releases. During routine tritium releases (continuously and constant releases), the local distribution of tritium reaches equilibrium, and specific activities of tritium in environmental compartments are almost equal. The situation is very different after an accidental emission. Having in view, harmful effects of tritium when it is incorporated into the body several models were developed for environmental tritium transport and dose assessment. The tritium transport into the soil is an important part of the environmental tritium behavior, but, unfortunately, in spite of the importance of this problem the corresponding modeling is unsatisfactory. The aim of this paper was the improvement of the TRICAIAP model, and the application of the model to BIOMOVS scenario. The BIOMOVS scenario predicts HTO concentrations in soil during 30 days, after one hour atmospheric HTO emission. The most important conclusions of the paper are: the principal carrier of tritium into the soil is water; the transfer processes are the reactions of water in soil and the diffusion due to concentration gradient; atmosphere-soil transport is dependent of surface characteristics (granulation, humidity, roughness, etc.); the conversion rate of HT to HTO is not well known and is dependent on active microorganism concentration in soil and on soil humidity. More experimental data are needed to decrease the uncertainty of transfer parameter, for the definition of the influence of vegetation, etc. (authors)

Effect of Flow Direction on Relative Permeability Curves in Water/Gas Reservoir System: Implications in Geological CO2 Sequestration

Directory of Open Access Journals (Sweden)

Abdulrauf Rasheed Adebayo

2017-01-01

Full Text Available The effect of gravity on vertical flow and fluids saturation, especially when flow is against gravity, is not often a subject of interest to researchers. This is because of the notion that flow in subsurface formations is usually in horizontal direction and that vertical flow is impossible or marginal because of the impermeable shales or silts overlying them. The density difference between two fluids (usually oil and water flowing in the porous media is also normally negligible; hence gravity influence is neglected. Capillarity is also often avoided in relative permeability measurements in order to satisfy some flow equations. These notions have guided most laboratory core flooding experiments to be conducted in horizontal flow orientation, and the data obtained are as good as what the experiments tend to mimic. However, gravity effect plays a major role in gas liquid systems such as CO2 sequestration and some types of enhanced oil recovery techniques, particularly those involving gases, where large density difference exists between the fluid pair. In such cases, laboratory experiments conducted to derive relative permeability curves should take into consideration gravity effects and capillarity. Previous studies attribute directional dependence of relative permeability and residual saturations to rock anisotropy. It is shown in this study that rock permeability, residual saturation, and relative permeability depend on the interplay between gravity, capillarity, and viscous forces and also the direction of fluid flow even when the rock is isotropic. Rock samples representing different lithology and wide range of permeabilities were investigated through unsteady-state experiments covering drainage and imbibition in both vertical and horizontal flow directions. The experiments were performed at very low flow rates to capture capillarity. The results obtained showed that, for each homogeneous rock and for the same flow path along the core length

Evaluation of permeability and swelling pressure of compacted bentonite using a calcium hydroxide solution

International Nuclear Information System (INIS)

Aoyagi, Takayoshi; Maeda, Munehiro; Mihara, Morihiro; Tanaka, Masuhiro

1998-12-01

Tests to determine the swelling pressure, permeability, compressive strength and elastic modulus of Ca-Na exchanged bentonite, Na-bentonite and Ca-bentonite at the Power Reactor and Nuclear Fuel Development Corporation have mainly used distilled water. However, disposal facilities for TRU waste will use cementateous material for packaging, backfill as well as structural support. In this case, a large amount of calcium will dissolve in groundwater flowing through the cementateous material. Therefore, it is important to investigate the mechanical properties of bentonite in calcium-rich water as part of the disposal research program for TRU waste. In order to understand the effect of the chemical composition of water on the basic mechanical properties of bentonite - part of evaluating the disposal concepts for TRU waste disposal - we tested the permeability of compacted bentonite under saturated conditions using a calcium hydroxide solution. The aqueous solution represents water dominated by the calcium component. Na-bentonite, Ca-Na exchanged bentonite and Ca-bentonite were used for swelling pressure measurement tests and permeability testing. Measures of the maximum and equilibrium swelling pressure as well as permeability we obtained. The dry density of bentonite was varied between tests. Results show that swelling pressure and permeability are dependent on dry density. In separate tests using Ca-bentonite, the bentonite-mixing rate was varied as an independent parameter. Results show that there is little change in the swelling pressure and permeability between tests using calcium hydroxide solution and distilled water for all bentonite types. (author)

Stress dependence of permeability of intact and fractured shale cores.

Science.gov (United States)

van Noort, Reinier; Yarushina, Viktoriya

2016-04-01

Whether a shale acts as a caprock, source rock, or reservoir, understanding fluid flow through shale is of major importance for understanding fluid flow in geological systems. Because of the low permeability of shale, flow is thought to be largely confined to fractures and similar features. In fracking operations, fractures are induced specifically to allow for hydrocarbon exploration. We have constructed an experimental setup to measure core permeabilities, using constant flow or a transient pulse. In this setup, we have measured the permeability of intact and fractured shale core samples, using either water or supercritical CO2 as the transporting fluid. Our measurements show decreasing permeability with increasing confining pressure, mainly due to time-dependent creep. Furthermore, our measurements show that for a simple splitting fracture, time-dependent creep will also eliminate any significant effect of this fracture on permeability. This effect of confinement on fracture permeability can have important implications regarding the effects of fracturing on shale permeability, and hence for operations depending on that.

Biofilm Effect on Flow Structure over a Permeable Bed

Science.gov (United States)

Kazemifar, F.; Blois, G.; Aybar, M.; Perez-Calleja, P.; Nerenberg, R.; Sinha, S.; Hardy, R. J.; Best, J.; Sambrook Smith, G.; Christensen, K. T.

2017-12-01

Biofilms constitute an important form of bacterial life in aquatic environments and are present at the fluid-solid interfaces in natural and industrial settings, such as water distribution systems and riverbeds among others. The permeable, heterogeneous, and deformable structure of biofilms can influence mass and momentum transport between the subsurface and freestream. However, this interaction is not fully understood, in part due to technical obstacles impeding quantitative experimental investigations. In this work, the effect of biofilm on flow structure over a permeable bed is studied. Experiments are conducted in a closed water channel equipped with an idealized two-dimensional permeable bed. Prior to conducting flow experiments, the models are placed within an independent recirculating reactor for biofilm growth. Once a targeted biofilm growth stage is achieved, the models are transferred to the water channel and subjected to transitional and turbulent flows. Long-distance microscopic particle image velocimetry measurements are performed to quantify the effect of biofilm on the turbulence structure of the free flow as well as the freestream-subsurface flow interaction.

Validation of the doubly-labeled water (H3H18O) method for measuring water flux and energy metabolism in tenebrionid beetles

International Nuclear Information System (INIS)

Cooper, P.D.

1981-01-01

Doubly-labeled water (H 3 H 18 O) has been used to determine water flux and energy metabolism in a variety of vertebrates. This study examines the applicability of this technique to arthropods. The theory of the technique depends upon the assumption that doubly-labeled water introduced into the animal's body water equilibrates with water and carbon dioxide by the action of carbonic anhydrase. Tritium ( 3 H) is lost from the animal only with water while oxygen-18 is lost with both water and carbon dioxide. The difference bwtween the rates of loss of the two isotopes is proportional to CO 2 loss rate. Validation of the use of tritiated water for measuring water flux was accomplished by comparing gravimetric measurements of water gain with flux rates determined by loss of tritiated water. At room humidity, an overestimate for influx calculated from labeled water calculations was found, averaging 12 mg H 2 O (g.d) -1 . Comparison of CO 2 loss rate determined isotopically with rates of CO 2 loss determined by standard metabolic rates also yielded overestimates for the isotopic technique, overestimates ranging between 20 and 30%. The relevance of this for studies using labeled water for studying water fluxes and free metabolism of free-ranging arthropods is discussed